3413 files changed, 225134 insertions, 67688 deletions

diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index f9aa0860f83e..a08c9d092a33 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -5,6 +5,7 @@ config ARM
 	select ARCH_32BIT_OFF_T
 	select ARCH_CORRECT_STACKTRACE_ON_KRETPROBE if HAVE_KRETPROBES && FRAME_POINTER && !ARM_UNWIND
 	select ARCH_HAS_BINFMT_FLAT
+	select ARCH_HAS_CURRENT_STACK_POINTER
 	select ARCH_HAS_DEBUG_VIRTUAL if MMU
 	select ARCH_HAS_DMA_WRITE_COMBINE if !ARM_DMA_MEM_BUFFERABLE
 	select ARCH_HAS_ELF_RANDOMIZE
@@ -14,13 +15,12 @@ config ARM
 	select ARCH_HAS_MEMBARRIER_SYNC_CORE
 	select ARCH_HAS_NON_OVERLAPPING_ADDRESS_SPACE
 	select ARCH_HAS_PTE_SPECIAL if ARM_LPAE
-	select ARCH_HAS_PHYS_TO_DMA
 	select ARCH_HAS_SETUP_DMA_OPS
 	select ARCH_HAS_SET_MEMORY
 	select ARCH_HAS_STRICT_KERNEL_RWX if MMU && !XIP_KERNEL
 	select ARCH_HAS_STRICT_MODULE_RWX if MMU
-	select ARCH_HAS_SYNC_DMA_FOR_DEVICE if SWIOTLB || !MMU
-	select ARCH_HAS_SYNC_DMA_FOR_CPU if SWIOTLB || !MMU
+	select ARCH_HAS_SYNC_DMA_FOR_DEVICE
+	select ARCH_HAS_SYNC_DMA_FOR_CPU
 	select ARCH_HAS_TEARDOWN_DMA_OPS if MMU
 	select ARCH_HAS_TICK_BROADCAST if GENERIC_CLOCKEVENTS_BROADCAST
 	select ARCH_HAVE_CUSTOM_GPIO_H
@@ -28,7 +28,6 @@ config ARM
 	select ARCH_HAS_GCOV_PROFILE_ALL
 	select ARCH_KEEP_MEMBLOCK
 	select ARCH_MIGHT_HAVE_PC_PARPORT
-	select ARCH_NO_SG_CHAIN if !ARM_HAS_SG_CHAIN
 	select ARCH_OPTIONAL_KERNEL_RWX if ARCH_HAS_STRICT_KERNEL_RWX
 	select ARCH_OPTIONAL_KERNEL_RWX_DEFAULT if CPU_V7
 	select ARCH_SUPPORTS_ATOMIC_RMW
@@ -37,17 +36,19 @@ config ARM
 	select ARCH_USE_CMPXCHG_LOCKREF
 	select ARCH_USE_MEMTEST
 	select ARCH_WANT_DEFAULT_TOPDOWN_MMAP_LAYOUT if MMU
+	select ARCH_WANT_GENERAL_HUGETLB
 	select ARCH_WANT_IPC_PARSE_VERSION
 	select ARCH_WANT_LD_ORPHAN_WARN
 	select BINFMT_FLAT_ARGVP_ENVP_ON_STACK
 	select BUILDTIME_TABLE_SORT if MMU
+	select COMMON_CLK if !(ARCH_RPC || ARCH_FOOTBRIDGE)
 	select CLONE_BACKWARDS
 	select CPU_PM if SUSPEND || CPU_IDLE
 	select DCACHE_WORD_ACCESS if HAVE_EFFICIENT_UNALIGNED_ACCESS
 	select DMA_DECLARE_COHERENT
 	select DMA_GLOBAL_POOL if !MMU
 	select DMA_OPS
-	select DMA_REMAP if MMU
+	select DMA_NONCOHERENT_MMAP if MMU
 	select EDAC_SUPPORT
 	select EDAC_ATOMIC_SCRUB
 	select GENERIC_ALLOCATOR
@@ -58,6 +59,7 @@ config ARM
 	select GENERIC_CPU_AUTOPROBE
 	select GENERIC_EARLY_IOREMAP
 	select GENERIC_IDLE_POLL_SETUP
+	select GENERIC_IRQ_MULTI_HANDLER
 	select GENERIC_IRQ_PROBE
 	select GENERIC_IRQ_SHOW
 	select GENERIC_IRQ_SHOW_LEVEL
@@ -69,8 +71,10 @@ config ARM
 	select HAVE_ARCH_AUDITSYSCALL if AEABI && !OABI_COMPAT
 	select HAVE_ARCH_BITREVERSE if (CPU_32v7M || CPU_32v7) && !CPU_32v6
 	select HAVE_ARCH_JUMP_LABEL if !XIP_KERNEL && !CPU_ENDIAN_BE32 && MMU
+	select HAVE_ARCH_KFENCE if MMU && !XIP_KERNEL
 	select HAVE_ARCH_KGDB if !CPU_ENDIAN_BE32 && MMU
 	select HAVE_ARCH_KASAN if MMU && !XIP_KERNEL
+	select HAVE_ARCH_KASAN_VMALLOC if HAVE_ARCH_KASAN
 	select HAVE_ARCH_MMAP_RND_BITS if MMU
 	select HAVE_ARCH_PFN_VALID
 	select HAVE_ARCH_SECCOMP
@@ -80,8 +84,9 @@ config ARM
 	select HAVE_ARCH_TRANSPARENT_HUGEPAGE if ARM_LPAE
 	select HAVE_ARM_SMCCC if CPU_V7
 	select HAVE_EBPF_JIT if !CPU_ENDIAN_BE32
-	select HAVE_CONTEXT_TRACKING
+	select HAVE_CONTEXT_TRACKING_USER
 	select HAVE_C_RECORDMCOUNT
+	select HAVE_BUILDTIME_MCOUNT_SORT
 	select HAVE_DEBUG_KMEMLEAK if !XIP_KERNEL
 	select HAVE_DMA_CONTIGUOUS if MMU
 	select HAVE_DYNAMIC_FTRACE if !XIP_KERNEL && !CPU_ENDIAN_BE32 && MMU
@@ -90,8 +95,8 @@ config ARM
 	select HAVE_EXIT_THREAD
 	select HAVE_FAST_GUP if ARM_LPAE
 	select HAVE_FTRACE_MCOUNT_RECORD if !XIP_KERNEL
-	select HAVE_FUNCTION_GRAPH_TRACER if !THUMB2_KERNEL && !CC_IS_CLANG
-	select HAVE_FUNCTION_TRACER if !XIP_KERNEL && !(THUMB2_KERNEL && CC_IS_CLANG)
+	select HAVE_FUNCTION_GRAPH_TRACER
+	select HAVE_FUNCTION_TRACER if !XIP_KERNEL
 	select HAVE_GCC_PLUGINS
 	select HAVE_HW_BREAKPOINT if PERF_EVENTS && (CPU_V6 || CPU_V6K || CPU_V7)
 	select HAVE_IRQ_TIME_ACCOUNTING
@@ -105,6 +110,7 @@ config ARM
 	select HAVE_MOD_ARCH_SPECIFIC
 	select HAVE_NMI
 	select HAVE_OPTPROBES if !THUMB2_KERNEL
+	select HAVE_PCI if MMU
 	select HAVE_PERF_EVENTS
 	select HAVE_PERF_REGS
 	select HAVE_PERF_USER_STACK_DUMP
@@ -121,12 +127,17 @@ config ARM
 	select OF_EARLY_FLATTREE if OF
 	select OLD_SIGACTION
 	select OLD_SIGSUSPEND3
+	select PCI_DOMAINS_GENERIC if PCI
 	select PCI_SYSCALL if PCI
 	select PERF_USE_VMALLOC
 	select RTC_LIB
+	select SPARSE_IRQ if !(ARCH_FOOTBRIDGE || ARCH_RPC)
 	select SYS_SUPPORTS_APM_EMULATION
-	select THREAD_INFO_IN_TASK if CURRENT_POINTER_IN_TPIDRURO
+	select THREAD_INFO_IN_TASK
+	select TIMER_OF if OF
+	select HAVE_ARCH_VMAP_STACK if MMU && ARM_HAS_GROUP_RELOCS
 	select TRACE_IRQFLAGS_SUPPORT if !CPU_V7M
+	select USE_OF if !(ARCH_FOOTBRIDGE || ARCH_RPC || ARCH_SA1100)
 	# Above selects are sorted alphabetically; please add new ones
 	# according to that.  Thanks.
 	help
@@ -137,12 +148,19 @@ config ARM
 	  Europe.  There is an ARM Linux project with a web page at
 	  <http://www.arm.linux.org.uk/>.
 
-config ARM_HAS_SG_CHAIN
-	bool
+config ARM_HAS_GROUP_RELOCS
+	def_bool y
+	depends on !LD_IS_LLD || LLD_VERSION >= 140000
+	depends on !COMPILE_TEST
+	help
+	  Whether or not to use R_ARM_ALU_PC_Gn or R_ARM_LDR_PC_Gn group
+	  relocations, which have been around for a long time, but were not
+	  supported in LLD until version 14. The combined range is -/+ 256 MiB,
+	  which is usually sufficient, but not for allyesconfig, so we disable
+	  this feature when doing compile testing.
 
 config ARM_DMA_USE_IOMMU
 	bool
-	select ARM_HAS_SG_CHAIN
 	select NEED_SG_DMA_LENGTH
 
 if ARM_DMA_USE_IOMMU
@@ -216,25 +234,19 @@ config ARCH_MAY_HAVE_PC_FDC
 config ARCH_SUPPORTS_UPROBES
 	def_bool y
 
-config ARCH_HAS_DMA_SET_COHERENT_MASK
-	bool
-
 config GENERIC_ISA_DMA
 	bool
 
 config FIQ
 	bool
 
-config NEED_RET_TO_USER
-	bool
-
 config ARCH_MTD_XIP
 	bool
 
 config ARM_PATCH_PHYS_VIRT
 	bool "Patch physical to virtual translations at runtime" if EMBEDDED
 	default y
-	depends on !XIP_KERNEL && MMU
+	depends on MMU
 	help
 	  Patch phys-to-virt and virt-to-phys translation functions at
 	  boot and module load time according to the position of the
@@ -263,9 +275,9 @@ config NEED_MACH_MEMORY_H
 
 config PHYS_OFFSET
 	hex "Physical address of main memory" if MMU
-	depends on !ARM_PATCH_PHYS_VIRT
+	depends on !ARM_PATCH_PHYS_VIRT || !AUTO_ZRELADDR
 	default DRAM_BASE if !MMU
-	default 0x00000000 if ARCH_FOOTBRIDGE || ARCH_IXP4XX
+	default 0x00000000 if ARCH_FOOTBRIDGE
 	default 0x10000000 if ARCH_OMAP1 || ARCH_RPC
 	default 0x30000000 if ARCH_S3C24XX
 	default 0xa0000000 if ARCH_IOP32X || ARCH_PXA
@@ -293,6 +305,12 @@ config MMU
 	  Select if you want MMU-based virtualised addressing space
 	  support by paged memory management. If unsure, say 'Y'.
 
+config ARM_SINGLE_ARMV7M
+	def_bool !MMU
+	select ARM_NVIC
+	select CPU_V7M
+	select NO_IOPORT_MAP
+
 config ARCH_MMAP_RND_BITS_MIN
 	default 8
 
@@ -301,223 +319,31 @@ config ARCH_MMAP_RND_BITS_MAX
 	default 15 if PAGE_OFFSET=0x80000000
 	default 16
 
-#
-# The "ARM system type" choice list is ordered alphabetically by option
-# text.  Please add new entries in the option alphabetic order.
-#
-choice
-	prompt "ARM system type"
-	default ARM_SINGLE_ARMV7M if !MMU
-	default ARCH_MULTIPLATFORM if MMU
-
 config ARCH_MULTIPLATFORM
-	bool "Allow multiple platforms to be selected"
-	depends on MMU
-	select ARCH_FLATMEM_ENABLE
-	select ARCH_SPARSEMEM_ENABLE
-	select ARCH_SELECT_MEMORY_MODEL
-	select ARM_HAS_SG_CHAIN
-	select ARM_PATCH_PHYS_VIRT
-	select AUTO_ZRELADDR
-	select TIMER_OF
-	select COMMON_CLK
-	select GENERIC_IRQ_MULTI_HANDLER
-	select HAVE_PCI
-	select PCI_DOMAINS_GENERIC if PCI
-	select SPARSE_IRQ
-	select USE_OF
-
-config ARM_SINGLE_ARMV7M
-	bool "ARMv7-M based platforms (Cortex-M0/M3/M4)"
-	depends on !MMU
-	select ARM_NVIC
-	select AUTO_ZRELADDR
-	select TIMER_OF
-	select COMMON_CLK
-	select CPU_V7M
-	select NO_IOPORT_MAP
-	select SPARSE_IRQ
-	select USE_OF
-
-config ARCH_EP93XX
-	bool "EP93xx-based"
-	select ARCH_SPARSEMEM_ENABLE
-	select ARM_AMBA
-	imply ARM_PATCH_PHYS_VIRT
-	select ARM_VIC
-	select GENERIC_IRQ_MULTI_HANDLER
-	select AUTO_ZRELADDR
-	select CLKSRC_MMIO
-	select CPU_ARM920T
-	select GPIOLIB
-	select COMMON_CLK
+	bool "Require kernel to be portable to multiple machines" if EXPERT
+	depends on MMU && !(ARCH_FOOTBRIDGE || ARCH_RPC || ARCH_SA1100)
+	default y
 	help
-	  This enables support for the Cirrus EP93xx series of CPUs.
+	  In general, all Arm machines can be supported in a single
+	  kernel image, covering either Armv4/v5 or Armv6/v7.
 
-config ARCH_FOOTBRIDGE
-	bool "FootBridge"
-	select CPU_SA110
-	select FOOTBRIDGE
-	select NEED_MACH_IO_H if !MMU
-	select NEED_MACH_MEMORY_H
-	help
-	  Support for systems based on the DC21285 companion chip
-	  ("FootBridge"), such as the Simtec CATS and the Rebel NetWinder.
+	  However, some configuration options require hardcoding machine
+	  specific physical addresses or enable errata workarounds that may
+	  break other machines.
 
-config ARCH_IOP32X
-	bool "IOP32x-based"
-	depends on MMU
-	select CPU_XSCALE
-	select GPIO_IOP
-	select GPIOLIB
-	select NEED_RET_TO_USER
-	select FORCE_PCI
-	select PLAT_IOP
-	help
-	  Support for Intel's 80219 and IOP32X (XScale) family of
-	  processors.
-
-config ARCH_IXP4XX
-	bool "IXP4xx-based"
-	depends on MMU
-	select ARCH_HAS_DMA_SET_COHERENT_MASK
-	select ARCH_SUPPORTS_BIG_ENDIAN
-	select CPU_XSCALE
-	select DMABOUNCE if PCI
-	select GENERIC_IRQ_MULTI_HANDLER
-	select GPIO_IXP4XX
-	select GPIOLIB
-	select HAVE_PCI
-	select IXP4XX_IRQ
-	select IXP4XX_TIMER
-	# With the new PCI driver this is not needed
-	select NEED_MACH_IO_H if IXP4XX_PCI_LEGACY
-	select USB_EHCI_BIG_ENDIAN_DESC
-	select USB_EHCI_BIG_ENDIAN_MMIO
-	help
-	  Support for Intel's IXP4XX (XScale) family of processors.
-
-config ARCH_DOVE
-	bool "Marvell Dove"
-	select CPU_PJ4
-	select GENERIC_IRQ_MULTI_HANDLER
-	select GPIOLIB
-	select HAVE_PCI
-	select MVEBU_MBUS
-	select PINCTRL
-	select PINCTRL_DOVE
-	select PLAT_ORION_LEGACY
-	select SPARSE_IRQ
-	select PM_GENERIC_DOMAINS if PM
-	help
-	  Support for the Marvell Dove SoC 88AP510
-
-config ARCH_PXA
-	bool "PXA2xx/PXA3xx-based"
-	depends on MMU
-	select ARCH_MTD_XIP
-	select ARM_CPU_SUSPEND if PM
-	select AUTO_ZRELADDR
-	select COMMON_CLK
-	select CLKSRC_PXA
-	select CLKSRC_MMIO
-	select TIMER_OF
-	select CPU_XSCALE if !CPU_XSC3
-	select GENERIC_IRQ_MULTI_HANDLER
-	select GPIO_PXA
-	select GPIOLIB
-	select IRQ_DOMAIN
-	select PLAT_PXA
-	select SPARSE_IRQ
-	help
-	  Support for Intel/Marvell's PXA2xx/PXA3xx processor line.
+	  Selecting N here allows using those options, including
+	  DEBUG_UNCOMPRESS, XIP_KERNEL and ZBOOT_ROM. If unsure, say Y.
 
-config ARCH_RPC
-	bool "RiscPC"
+menu "Platform selection"
 	depends on MMU
-	depends on !CC_IS_CLANG && GCC_VERSION < 90100 && GCC_VERSION >= 60000
-	select ARCH_ACORN
-	select ARCH_MAY_HAVE_PC_FDC
-	select ARCH_SPARSEMEM_ENABLE
-	select ARM_HAS_SG_CHAIN
-	select CPU_SA110
-	select FIQ
-	select HAVE_PATA_PLATFORM
-	select ISA_DMA_API
-	select LEGACY_TIMER_TICK
-	select NEED_MACH_IO_H
-	select NEED_MACH_MEMORY_H
-	select NO_IOPORT_MAP
-	help
-	  On the Acorn Risc-PC, Linux can support the internal IDE disk and
-	  CD-ROM interface, serial and parallel port, and the floppy drive.
-
-config ARCH_SA1100
-	bool "SA1100-based"
-	select ARCH_MTD_XIP
-	select ARCH_SPARSEMEM_ENABLE
-	select CLKSRC_MMIO
-	select CLKSRC_PXA
-	select TIMER_OF if OF
-	select COMMON_CLK
-	select CPU_FREQ
-	select CPU_SA1100
-	select GENERIC_IRQ_MULTI_HANDLER
-	select GPIOLIB
-	select IRQ_DOMAIN
-	select ISA
-	select NEED_MACH_MEMORY_H
-	select SPARSE_IRQ
-	help
-	  Support for StrongARM 11x0 based boards.
-
-config ARCH_S3C24XX
-	bool "Samsung S3C24XX SoCs"
-	select ATAGS
-	select CLKSRC_SAMSUNG_PWM
-	select GPIO_SAMSUNG
-	select GPIOLIB
-	select GENERIC_IRQ_MULTI_HANDLER
-	select HAVE_S3C2410_I2C if I2C
-	select NEED_MACH_IO_H
-	select S3C2410_WATCHDOG
-	select SAMSUNG_ATAGS
-	select USE_OF
-	select WATCHDOG
-	help
-	  Samsung S3C2410, S3C2412, S3C2413, S3C2416, S3C2440, S3C2442, S3C2443
-	  and S3C2450 SoCs based systems, such as the Simtec Electronics BAST
-	  (<http://www.simtec.co.uk/products/EB110ITX/>), the IPAQ 1940 or the
-	  Samsung SMDK2410 development board (and derivatives).
-
-config ARCH_OMAP1
-	bool "TI OMAP1"
-	depends on MMU
-	select ARCH_OMAP
-	select CLKSRC_MMIO
-	select GENERIC_IRQ_CHIP
-	select GENERIC_IRQ_MULTI_HANDLER
-	select GPIOLIB
-	select HAVE_LEGACY_CLK
-	select IRQ_DOMAIN
-	select NEED_MACH_IO_H if PCCARD
-	select NEED_MACH_MEMORY_H
-	select SPARSE_IRQ
-	help
-	  Support for older TI OMAP1 (omap7xx, omap15xx or omap16xx)
-
-endchoice
-
-menu "Multiple platform selection"
-	depends on ARCH_MULTIPLATFORM
 
 comment "CPU Core family selection"
 
 config ARCH_MULTI_V4
-	bool "ARMv4 based platforms (FA526)"
+	bool "ARMv4 based platforms (FA526, StrongARM)"
 	depends on !ARCH_MULTI_V6_V7
 	select ARCH_MULTI_V4_V5
-	select CPU_FA526
+	select CPU_FA526 if !(CPU_SA110 || CPU_SA1100)
 
 config ARCH_MULTI_V4T
 	bool "ARMv4T based platforms (ARM720T, ARM920T, ...)"
@@ -570,7 +396,17 @@ config ARCH_VIRT
 	select ARM_GIC_V3_ITS if PCI
 	select ARM_PSCI
 	select HAVE_ARM_ARCH_TIMER
-	select ARCH_SUPPORTS_BIG_ENDIAN
+
+config ARCH_AIROHA
+	bool "Airoha SoC Support"
+	depends on ARCH_MULTI_V7
+	select ARM_AMBA
+	select ARM_GIC
+	select ARM_GIC_V3
+	select ARM_PSCI
+	select HAVE_ARM_ARCH_TIMER
+	help
+	  Support for Airoha EN7523 SoCs
 
 #
 # This is sorted alphabetically by mach-* pathname.  However, plat-*
@@ -617,9 +453,9 @@ source "arch/arm/mach-highbank/Kconfig"
 
 source "arch/arm/mach-hisi/Kconfig"
 
-source "arch/arm/mach-imx/Kconfig"
+source "arch/arm/mach-hpe/Kconfig"
 
-source "arch/arm/mach-integrator/Kconfig"
+source "arch/arm/mach-imx/Kconfig"
 
 source "arch/arm/mach-iop32x/Kconfig"
 
@@ -653,8 +489,6 @@ source "arch/arm/mach-npcm/Kconfig"
 
 source "arch/arm/mach-nspire/Kconfig"
 
-source "arch/arm/plat-omap/Kconfig"
-
 source "arch/arm/mach-omap1/Kconfig"
 
 source "arch/arm/mach-omap2/Kconfig"
@@ -664,7 +498,6 @@ source "arch/arm/mach-orion5x/Kconfig"
 source "arch/arm/mach-oxnas/Kconfig"
 
 source "arch/arm/mach-pxa/Kconfig"
-source "arch/arm/plat-pxa/Kconfig"
 
 source "arch/arm/mach-qcom/Kconfig"
 
@@ -672,7 +505,7 @@ source "arch/arm/mach-rda/Kconfig"
 
 source "arch/arm/mach-realtek/Kconfig"
 
-source "arch/arm/mach-realview/Kconfig"
+source "arch/arm/mach-rpc/Kconfig"
 
 source "arch/arm/mach-rockchip/Kconfig"
 
@@ -692,6 +525,8 @@ source "arch/arm/mach-sti/Kconfig"
 
 source "arch/arm/mach-stm32/Kconfig"
 
+source "arch/arm/mach-sunplus/Kconfig"
+
 source "arch/arm/mach-sunxi/Kconfig"
 
 source "arch/arm/mach-tegra/Kconfig"
@@ -702,8 +537,6 @@ source "arch/arm/mach-ux500/Kconfig"
 
 source "arch/arm/mach-versatile/Kconfig"
 
-source "arch/arm/mach-vexpress/Kconfig"
-
 source "arch/arm/mach-vt8500/Kconfig"
 
 source "arch/arm/mach-zynq/Kconfig"
@@ -736,13 +569,9 @@ config ARCH_MPS2
 config ARCH_ACORN
 	bool
 
-config PLAT_IOP
-	bool
-
 config PLAT_ORION
 	bool
 	select CLKSRC_MMIO
-	select COMMON_CLK
 	select GENERIC_IRQ_CHIP
 	select IRQ_DOMAIN
 
@@ -750,9 +579,6 @@ config PLAT_ORION_LEGACY
 	bool
 	select PLAT_ORION
 
-config PLAT_PXA
-	bool
-
 config PLAT_VERSATILE
 	bool
 
@@ -969,6 +795,17 @@ config ARM_ERRATA_764369
 	  relevant cache maintenance functions and sets a specific bit
 	  in the diagnostic control register of the SCU.
 
+config ARM_ERRATA_764319
+	bool "ARM errata: Read to DBGPRSR and DBGOSLSR may generate Undefined instruction"
+	depends on CPU_V7
+	help
+	  This option enables the workaround for the 764319 Cortex A-9 erratum.
+	  CP14 read accesses to the DBGPRSR and DBGOSLSR registers generate an
+	  unexpected Undefined Instruction exception when the DBGSWENABLE
+	  external pin is set to 0, even when the CP14 accesses are performed
+	  from a privileged mode. This work around catches the exception in a
+	  way the kernel does not stop execution.
+
 config ARM_ERRATA_775420
        bool "ARM errata: A data cache maintenance operation which aborts, might lead to deadlock"
        depends on CPU_V7
@@ -1085,11 +922,6 @@ config ISA
 	  (MCA) or VESA.  ISA is an older system, now being displaced by PCI;
 	  newer boards don't support it.  If you have ISA, say Y, otherwise N.
 
-# Select ISA DMA controller support
-config ISA_DMA
-	bool
-	select ISA_DMA_API
-
 # Select ISA DMA interface
 config ISA_DMA_API
 	bool
@@ -1150,7 +982,7 @@ config SMP
 
 config SMP_ON_UP
 	bool "Allow booting SMP kernel on uniprocessor systems"
-	depends on SMP && !XIP_KERNEL && MMU
+	depends on SMP && MMU
 	default y
 	help
 	  SMP kernels contain instructions which fail on non-SMP processors.
@@ -1163,7 +995,12 @@ config SMP_ON_UP
 
 config CURRENT_POINTER_IN_TPIDRURO
 	def_bool y
-	depends on SMP && CPU_32v6K && !CPU_V6
+	depends on CPU_32v6K && !CPU_V6
+
+config IRQSTACKS
+	def_bool y
+	select HAVE_IRQ_EXIT_ON_IRQ_STACK
+	select HAVE_SOFTIRQ_ON_OWN_STACK
 
 config ARM_CPU_TOPOLOGY
 	bool "Support cpu topology definition"
@@ -1394,7 +1231,7 @@ config THUMB2_KERNEL
 
 config ARM_PATCH_IDIV
 	bool "Runtime patch udiv/sdiv instructions into __aeabi_{u}idiv()"
-	depends on CPU_32v7 && !XIP_KERNEL
+	depends on CPU_32v7
 	default y
 	help
 	  The ARM compiler inserts calls to __aeabi_idiv() and
@@ -1449,13 +1286,13 @@ config OABI_COMPAT
 	  at all). If in doubt say N.
 
 config ARCH_SELECT_MEMORY_MODEL
-	bool
+	def_bool y
 
 config ARCH_FLATMEM_ENABLE
-	bool
+	def_bool !(ARCH_RPC || ARCH_SA1100)
 
 config ARCH_SPARSEMEM_ENABLE
-	bool
+	def_bool !ARCH_FOOTBRIDGE
 	select SPARSEMEM_STATIC if SPARSEMEM
 
 config HIGHMEM
@@ -1507,12 +1344,10 @@ config HW_PERF_EVENTS
 	def_bool y
 	depends on ARM_PMU
 
-config ARCH_WANT_GENERAL_HUGETLB
-	def_bool y
-
 config ARM_MODULE_PLTS
 	bool "Use PLTs to allow module memory to spill over into vmalloc area"
 	depends on MODULES
+	select KASAN_VMALLOC if KASAN
 	default y
 	help
 	  Allocate PLTs when loading modules so that jumps and calls whose
@@ -1527,7 +1362,7 @@ config ARM_MODULE_PLTS
 	  Disabling this is usually safe for small single-platform
 	  configurations. If unsure, say y.
 
-config FORCE_MAX_ZONEORDER
+config ARCH_FORCE_MAX_ORDER
 	int "Maximum zone order"
 	default "12" if SOC_AM33XX
 	default "9" if SA1111
@@ -1607,10 +1442,14 @@ config XEN
 	help
 	  Say Y if you want to run Linux in a Virtual Machine on Xen on ARM.
 
+config CC_HAVE_STACKPROTECTOR_TLS
+	def_bool $(cc-option,-mtp=cp15 -mstack-protector-guard=tls -mstack-protector-guard-offset=0)
+
 config STACKPROTECTOR_PER_TASK
 	bool "Use a unique stack canary value for each task"
-	depends on GCC_PLUGINS && STACKPROTECTOR && THREAD_INFO_IN_TASK && !XIP_DEFLATED_DATA
-	select GCC_PLUGIN_ARM_SSP_PER_TASK
+	depends on STACKPROTECTOR && CURRENT_POINTER_IN_TPIDRURO && !XIP_DEFLATED_DATA
+	depends on GCC_PLUGINS || CC_HAVE_STACKPROTECTOR_TLS
+	select GCC_PLUGIN_ARM_SSP_PER_TASK if !CC_HAVE_STACKPROTECTOR_TLS
 	default y
 	help
 	  Due to the fact that GCC uses an ordinary symbol reference from
@@ -1634,14 +1473,26 @@ config USE_OF
 	  Include support for flattened device tree machine descriptions.
 
 config ATAGS
-	bool "Support for the traditional ATAGS boot data passing" if USE_OF
+	bool "Support for the traditional ATAGS boot data passing"
 	default y
 	help
 	  This is the traditional way of passing data to the kernel at boot
 	  time. If you are solely relying on the flattened device tree (or
 	  the ARM_ATAG_DTB_COMPAT option) then you may unselect this option
-	  to remove ATAGS support from your kernel binary.  If unsure,
-	  leave this to y.
+	  to remove ATAGS support from your kernel binary.
+
+config UNUSED_BOARD_FILES
+	bool "Board support for machines without known users"
+	depends on ATAGS
+	help
+	  Most ATAGS based board files are completely unused and are
+	  scheduled for removal in early 2023, and left out of kernels
+	  by default now.  If you are using a board file that is marked
+	  as unused, turn on this option to build support into the kernel.
+
+	  To keep support for your individual board from being removed,
+	  send a reply to the email discussion at
+	  https://lore.kernel.org/all/CAK8P3a0Z9vGEQbVRBo84bSyPFM-LF+hs5w8ZA51g2Z+NsdtDQA@mail.gmail.com/
 
 config DEPRECATED_PARAM_STRUCT
 	bool "Provide old way to pass kernel parameters"
@@ -1748,7 +1599,6 @@ config CMDLINE
 choice
 	prompt "Kernel command line type" if CMDLINE != ""
 	default CMDLINE_FROM_BOOTLOADER
-	depends on ATAGS
 
 config CMDLINE_FROM_BOOTLOADER
 	bool "Use bootloader kernel arguments if available"
@@ -1775,6 +1625,7 @@ endchoice
 config XIP_KERNEL
 	bool "Kernel Execute-In-Place from ROM"
 	depends on !ARM_LPAE && !ARCH_MULTIPLATFORM
+	depends on !ARM_PATCH_IDIV && !ARM_PATCH_PHYS_VIRT && !SMP_ON_UP
 	help
 	  Execute-In-Place allows the kernel to run from non-volatile storage
 	  directly addressable by the CPU, such as NOR flash. This saves RAM
@@ -1849,7 +1700,8 @@ config CRASH_DUMP
 	  For more details see Documentation/admin-guide/kdump/kdump.rst
 
 config AUTO_ZRELADDR
-	bool "Auto calculation of the decompressed kernel image address"
+	bool "Auto calculation of the decompressed kernel image address" if !ARCH_MULTIPLATFORM
+	default !(ARCH_FOOTBRIDGE || ARCH_RPC || ARCH_SA1100)
 	help
 	  ZRELADDR is the physical address where the decompressed kernel
 	  image will be placed. If AUTO_ZRELADDR is selected, the address
@@ -1998,8 +1850,4 @@ config ARCH_HIBERNATION_POSSIBLE
 
 endmenu
 
-if CRYPTO
-source "arch/arm/crypto/Kconfig"
-endif
-
 source "arch/arm/Kconfig.assembler"
diff --git a/arch/arm/Kconfig.debug b/arch/arm/Kconfig.debug
index 98436702e0c7..c345775f035b 100644
--- a/arch/arm/Kconfig.debug
+++ b/arch/arm/Kconfig.debug
@@ -65,9 +65,7 @@ config UNWINDER_FRAME_POINTER
 
 config UNWINDER_ARM
 	bool "ARM EABI stack unwinder"
-	depends on AEABI && !FUNCTION_GRAPH_TRACER
-	# https://github.com/ClangBuiltLinux/linux/issues/732
-	depends on !LD_IS_LLD || LLD_VERSION >= 110000
+	depends on AEABI
 	select ARM_UNWIND
 	help
 	  This option enables stack unwinding support in the kernel
@@ -81,6 +79,17 @@ endchoice
 config ARM_UNWIND
 	bool
 
+config BACKTRACE_VERBOSE
+	bool "Verbose backtrace"
+	depends on EXPERT
+	help
+	  When the kernel produces a warning or oops, the kernel prints a
+	  trace of the call chain. This option controls whether we include
+	  the numeric addresses or only include the symbolic information.
+
+	  In most cases, say N here, unless you are intending to debug the
+	  kernel and have access to the kernel binary image.
+
 config FRAME_POINTER
 	bool
 
@@ -201,6 +210,26 @@ choice
 		  Say Y here if you want kernel low-level debugging support
 		  on the FLEXCOM3 port of SAMA7G5.
 
+	config DEBUG_AT91_LAN966_FLEXCOM
+		bool "Kernel low-level debugging on LAN966 FLEXCOM USART"
+		select DEBUG_AT91_UART
+		depends on SOC_LAN966
+		help
+		Say Y here if you want kernel low-level debugging support
+		on the FLEXCOM port of LAN966.
+
+		DEBUG_UART_PHYS | DEBUG_UART_VIRT
+
+		0xe0040200      | 0xfd040200     | FLEXCOM0
+		0xe0044200      | 0xfd044200     | FLEXCOM1
+		0xe0060200      | 0xfd060200     | FLEXCOM2
+		0xe0064200      | 0xfd064200     | FLEXCOM3
+		0xe0070200      | 0xfd070200     | FLEXCOM4
+
+		By default, enabling FLEXCOM3 port. Based on requirement, use
+		DEBUG_UART_PHYS and DEBUG_UART_VIRT configurations from above
+		table.
+
 	config DEBUG_BCM2835
 		bool "Kernel low-level debugging on BCM2835 PL011 UART"
 		depends on ARCH_BCM2835 && ARCH_MULTI_V6
@@ -242,7 +271,7 @@ choice
 
 	config DEBUG_BCM63XX_UART
 		bool "Kernel low-level debugging on BCM63XX UART"
-		depends on ARCH_BCM_63XX
+		depends on ARCH_BCMBCA
 
 	config DEBUG_BERLIN_UART
 		bool "Marvell Berlin SoC Debug UART"
@@ -410,12 +439,12 @@ choice
 		  Say Y here if you want kernel low-level debugging support
 		  on i.MX25.
 
-	config DEBUG_IMX21_IMX27_UART
-		bool "i.MX21 and i.MX27 Debug UART"
-		depends on SOC_IMX21 || SOC_IMX27
+	config DEBUG_IMX27_UART
+		bool "i.MX27 Debug UART"
+		depends on SOC_IMX27
 		help
 		  Say Y here if you want kernel low-level debugging support
-		  on i.MX21 or i.MX27.
+		  on i.MX27.
 
 	config DEBUG_IMX28_UART
 		bool "i.MX28 Debug UART"
@@ -1481,7 +1510,7 @@ config DEBUG_IMX_UART_PORT
 	int "i.MX Debug UART Port Selection"
 	depends on DEBUG_IMX1_UART || \
 		   DEBUG_IMX25_UART || \
-		   DEBUG_IMX21_IMX27_UART || \
+		   DEBUG_IMX27_UART || \
 		   DEBUG_IMX31_UART || \
 		   DEBUG_IMX35_UART || \
 		   DEBUG_IMX50_UART || \
@@ -1540,12 +1569,12 @@ config DEBUG_LL_INCLUDE
 	default "debug/icedcc.S" if DEBUG_ICEDCC
 	default "debug/imx.S" if DEBUG_IMX1_UART || \
 				 DEBUG_IMX25_UART || \
-				 DEBUG_IMX21_IMX27_UART || \
+				 DEBUG_IMX27_UART || \
 				 DEBUG_IMX31_UART || \
 				 DEBUG_IMX35_UART || \
 				 DEBUG_IMX50_UART || \
 				 DEBUG_IMX51_UART || \
-				 DEBUG_IMX53_UART ||\
+				 DEBUG_IMX53_UART || \
 				 DEBUG_IMX6Q_UART || \
 				 DEBUG_IMX6SL_UART || \
 				 DEBUG_IMX6SX_UART || \
@@ -1676,6 +1705,7 @@ config DEBUG_UART_PHYS
 	default 0xd4017000 if DEBUG_MMP_UART2
 	default 0xd4018000 if DEBUG_MMP_UART3
 	default 0xe0000000 if DEBUG_SPEAR13XX
+	default 0xe0064200 if DEBUG_AT91_LAN966_FLEXCOM
 	default 0xe1824200 if DEBUG_AT91_SAMA7G5_FLEXCOM3
 	default 0xe4007000 if DEBUG_HIP04_UART
 	default 0xe6c40000 if DEBUG_RMOBILE_SCIFA0
@@ -1796,6 +1826,7 @@ config DEBUG_UART_VIRT
 	default 0xfb10c000 if DEBUG_REALVIEW_PB1176_PORT
 	default 0xfcfe8600 if DEBUG_BCM63XX_UART
 	default 0xfd000000 if DEBUG_SPEAR3XX || DEBUG_SPEAR13XX
+	default 0xfd064200 if DEBUG_AT91_LAN966_FLEXCOM
 	default 0xfd531000 if DEBUG_STIH41X_SBC_ASC1
 	default 0xfd883000 if DEBUG_ALPINE_UART0
 	default 0xfdd32000 if DEBUG_STIH41X_ASC2
@@ -1828,9 +1859,9 @@ config DEBUG_UART_VIRT
 	default 0xfec00000 if ARCH_IXP4XX && !CPU_BIG_ENDIAN
 	default 0xfec00003 if ARCH_IXP4XX && CPU_BIG_ENDIAN
 	default 0xfef36000 if DEBUG_HIGHBANK_UART
-	default 0xfefb0000 if DEBUG_OMAP1UART1 || DEBUG_OMAP7XXUART1
-	default 0xfefb0800 if DEBUG_OMAP1UART2 || DEBUG_OMAP7XXUART2
-	default 0xfefb9800 if DEBUG_OMAP1UART3 || DEBUG_OMAP7XXUART3
+	default 0xff0b0000 if DEBUG_OMAP1UART1 || DEBUG_OMAP7XXUART1
+	default 0xff0b0800 if DEBUG_OMAP1UART2 || DEBUG_OMAP7XXUART2
+	default 0xff0b9800 if DEBUG_OMAP1UART3 || DEBUG_OMAP7XXUART3
 	default 0xffd01000 if DEBUG_HIP01_UART
 	default DEBUG_UART_PHYS if !MMU
 	depends on DEBUG_LL_UART_8250 || DEBUG_LL_UART_PL01X || \
@@ -1873,7 +1904,8 @@ config DEBUG_UART_8250_PALMCHIP
 
 config DEBUG_UNCOMPRESS
 	bool "Enable decompressor debugging via DEBUG_LL output"
-	depends on ARCH_MULTIPLATFORM || PLAT_SAMSUNG || ARM_SINGLE_ARMV7M
+	depends on !ARCH_MULTIPLATFORM
+	depends on !(ARCH_FOOTBRIDGE || ARCH_RPC || ARCH_SA1100)
 	depends on DEBUG_LL && !DEBUG_OMAP2PLUS_UART && \
 		     (!DEBUG_TEGRA_UART || !ZBOOT_ROM) && \
 		     !DEBUG_BRCMSTB_UART && !DEBUG_SEMIHOSTING
@@ -1890,9 +1922,8 @@ config DEBUG_UNCOMPRESS
 
 config UNCOMPRESS_INCLUDE
 	string
-	default "debug/uncompress.h" if ARCH_MULTIPLATFORM || ARCH_MSM || \
-					PLAT_SAMSUNG || ARM_SINGLE_ARMV7M
-	default "mach/uncompress.h"
+	default "mach/uncompress.h" if ARCH_FOOTBRIDGE || ARCH_RPC || ARCH_SA1100
+	default "debug/uncompress.h"
 
 config EARLY_PRINTK
 	bool "Early printk"
diff --git a/arch/arm/Makefile b/arch/arm/Makefile
index 77172d555c7e..c846119c448f 100644
--- a/arch/arm/Makefile
+++ b/arch/arm/Makefile
@@ -22,6 +22,9 @@ GZFLAGS		:=-9
 # Never generate .eh_frame
 KBUILD_CFLAGS	+= $(call cc-option,-fno-dwarf2-cfi-asm)
 
+# Disable FDPIC ABI
+KBUILD_CFLAGS	+= $(call cc-option,-mno-fdpic)
+
 # This should work on most of the modern platforms
 KBUILD_DEFCONFIG := multi_v7_defconfig
 
@@ -134,9 +137,6 @@ KBUILD_AFLAGS	+=$(CFLAGS_ABI) $(AFLAGS_ISA) $(arch-y) $(tune-y) -include asm/uni
 
 CHECKFLAGS	+= -D__arm__
 
-#Default value
-head-y		:= arch/arm/kernel/head$(MMUEXT).o
-
 # Text offset. This list is sorted numerically by address in order to
 # provide a means to avoid/resolve conflicts in multi-arch kernels.
 # Note: the 32kB below this value is reserved for use by the kernel
@@ -160,6 +160,7 @@ textofs-$(CONFIG_ARCH_AXXIA) := 0x00308000
 # Machine directory name.  This list is sorted alphanumerically
 # by CONFIG_* macro name.
 machine-$(CONFIG_ARCH_ACTIONS)		+= actions
+machine-$(CONFIG_ARCH_AIROHA)		+= airoha
 machine-$(CONFIG_ARCH_ALPINE)		+= alpine
 machine-$(CONFIG_ARCH_ARTPEC)		+= artpec
 machine-$(CONFIG_ARCH_ASPEED)           += aspeed
@@ -178,7 +179,7 @@ machine-$(CONFIG_ARCH_FOOTBRIDGE)	+= footbridge
 machine-$(CONFIG_ARCH_GEMINI)		+= gemini
 machine-$(CONFIG_ARCH_HIGHBANK)		+= highbank
 machine-$(CONFIG_ARCH_HISI)		+= hisi
-machine-$(CONFIG_ARCH_INTEGRATOR)	+= integrator
+machine-$(CONFIG_ARCH_HPE)		+= hpe
 machine-$(CONFIG_ARCH_IOP32X)		+= iop32x
 machine-$(CONFIG_ARCH_IXP4XX)		+= ixp4xx
 machine-$(CONFIG_ARCH_KEYSTONE)		+= keystone
@@ -186,7 +187,6 @@ machine-$(CONFIG_ARCH_LPC18XX)		+= lpc18xx
 machine-$(CONFIG_ARCH_LPC32XX)		+= lpc32xx
 machine-$(CONFIG_ARCH_MESON)		+= meson
 machine-$(CONFIG_ARCH_MMP)		+= mmp
-machine-$(CONFIG_ARCH_MPS2)		+= vexpress
 machine-$(CONFIG_ARCH_MOXART)		+= moxart
 machine-$(CONFIG_ARCH_MV78XX0)		+= mv78xx0
 machine-$(CONFIG_ARCH_MVEBU)		+= mvebu
@@ -206,7 +206,6 @@ machine-$(CONFIG_ARCH_PXA)		+= pxa
 machine-$(CONFIG_ARCH_QCOM)		+= qcom
 machine-$(CONFIG_ARCH_RDA)		+= rda
 machine-$(CONFIG_ARCH_REALTEK)		+= realtek
-machine-$(CONFIG_ARCH_REALVIEW)		+= realview
 machine-$(CONFIG_ARCH_ROCKCHIP)		+= rockchip
 machine-$(CONFIG_ARCH_RPC)		+= rpc
 machine-$(CONFIG_PLAT_SAMSUNG)		+= s3c
@@ -216,52 +215,33 @@ machine-$(CONFIG_ARCH_RENESAS)	 	+= shmobile
 machine-$(CONFIG_ARCH_INTEL_SOCFPGA)	+= socfpga
 machine-$(CONFIG_ARCH_STI)		+= sti
 machine-$(CONFIG_ARCH_STM32)		+= stm32
+machine-$(CONFIG_ARCH_SUNPLUS)		+= sunplus
 machine-$(CONFIG_ARCH_SUNXI)		+= sunxi
 machine-$(CONFIG_ARCH_TEGRA)		+= tegra
 machine-$(CONFIG_ARCH_U8500)		+= ux500
-machine-$(CONFIG_ARCH_VERSATILE)	+= versatile
-machine-$(CONFIG_ARCH_VEXPRESS)		+= vexpress
 machine-$(CONFIG_ARCH_VT8500)		+= vt8500
 machine-$(CONFIG_ARCH_ZYNQ)		+= zynq
+machine-$(CONFIG_PLAT_VERSATILE)	+= versatile
 machine-$(CONFIG_PLAT_SPEAR)		+= spear
 
-# Platform directory name.  This list is sorted alphanumerically
-# by CONFIG_* macro name.
-plat-$(CONFIG_ARCH_OMAP)	+= omap
-plat-$(CONFIG_PLAT_ORION)	+= orion
-plat-$(CONFIG_PLAT_PXA)		+= pxa
-plat-$(CONFIG_PLAT_VERSATILE)	+= versatile
+# legacy platforms provide their own mach/*.h headers globally,
+# these three are mutually exclusive
+machdirs-$(CONFIG_ARCH_FOOTBRIDGE)	+= arch/arm/mach-footbridge
+machdirs-$(CONFIG_ARCH_RPC)		+= arch/arm/mach-rpc
+machdirs-$(CONFIG_ARCH_SA1100)		+= arch/arm/mach-sa1100
+KBUILD_CPPFLAGS += $(patsubst %,-I$(srctree)/%/include,$(machdirs-y))
 
 # The byte offset of the kernel image in RAM from the start of RAM.
 TEXT_OFFSET := $(textofs-y)
 
-# The first directory contains additional information for the boot setup code
-ifneq ($(machine-y),)
-MACHINE  := arch/arm/mach-$(word 1,$(machine-y))/
-else
-MACHINE  :=
-endif
-ifeq ($(CONFIG_ARCH_MULTIPLATFORM),y)
-MACHINE  :=
-endif
-
-machdirs := $(patsubst %,arch/arm/mach-%/,$(machine-y))
-platdirs := $(patsubst %,arch/arm/plat-%/,$(sort $(plat-y)))
-
-ifneq ($(CONFIG_ARCH_MULTIPLATFORM),y)
-ifneq ($(CONFIG_ARM_SINGLE_ARMV7M),y)
-KBUILD_CPPFLAGS += $(patsubst %,-I$(srctree)/%include,$(machdirs) $(platdirs))
-endif
-endif
-
 export	TEXT_OFFSET GZFLAGS MMUEXT
 
 # If we have a machine-specific directory, then include it in the build.
-core-y				+= $(machdirs) $(platdirs)
-
+core-y				+= $(patsubst %,arch/arm/mach-%/,$(machine-y))
 # For cleaning
-core-				+= $(patsubst %,arch/arm/mach-%/, $(machine-))
-core-				+= $(patsubst %,arch/arm/plat-%/, $(plat-))
+core-				+= $(patsubst %,arch/arm/mach-%/,$(machine-))
+
+core-$(CONFIG_PLAT_ORION)	+= arch/arm/plat-orion/
 
 libs-y				:= arch/arm/lib/ $(libs-y)
 
@@ -275,6 +255,14 @@ endif
 
 ifeq ($(CONFIG_STACKPROTECTOR_PER_TASK),y)
 prepare: stack_protector_prepare
+ifeq ($(CONFIG_CC_HAVE_STACKPROTECTOR_TLS),y)
+stack_protector_prepare: prepare0
+	$(eval KBUILD_CFLAGS += \
+		-mstack-protector-guard=tls \
+		-mstack-protector-guard-offset=$(shell	\
+			awk '{if ($$2 == "TSK_STACK_CANARY") print $$3;}'\
+				include/generated/asm-offsets.h))
+else
 stack_protector_prepare: prepare0
 	$(eval SSP_PLUGIN_CFLAGS := \
 		-fplugin-arg-arm_ssp_per_task_plugin-offset=$(shell	\
@@ -283,6 +271,7 @@ stack_protector_prepare: prepare0
 	$(eval KBUILD_CFLAGS += $(SSP_PLUGIN_CFLAGS))
 	$(eval GCC_PLUGINS_CFLAGS += $(SSP_PLUGIN_CFLAGS))
 endif
+endif
 
 all:	$(notdir $(KBUILD_IMAGE))
 
@@ -305,12 +294,12 @@ bootpImage uImage: zImage
 zImage: Image
 
 $(BOOT_TARGETS): vmlinux
-	$(Q)$(MAKE) $(build)=$(boot) MACHINE=$(MACHINE) $(boot)/$@
+	$(Q)$(MAKE) $(build)=$(boot) $(boot)/$@
 	@$(kecho) '  Kernel: $(boot)/$@ is ready'
 
+$(INSTALL_TARGETS): KBUILD_IMAGE = $(boot)/$(patsubst %install,%Image,$@)
 $(INSTALL_TARGETS):
-	$(CONFIG_SHELL) $(srctree)/$(boot)/install.sh "$(KERNELRELEASE)" \
-	$(boot)/$(patsubst %install,%Image,$@) System.map "$(INSTALL_PATH)"
+	$(call cmd,install)
 
 PHONY += vdso_install
 vdso_install:
@@ -319,7 +308,7 @@ ifeq ($(CONFIG_VDSO),y)
 endif
 
 # My testing targets (bypasses dependencies)
-bp:;	$(Q)$(MAKE) $(build)=$(boot) MACHINE=$(MACHINE) $(boot)/bootpImage
+bp:;	$(Q)$(MAKE) $(build)=$(boot) $(boot)/bootpImage
 
 
 define archhelp
diff --git a/arch/arm/boot/Makefile b/arch/arm/boot/Makefile
index 54a09f9464fb..abd6a2889fd0 100644
--- a/arch/arm/boot/Makefile
+++ b/arch/arm/boot/Makefile
@@ -10,22 +10,16 @@
 #
 # Copyright (C) 1995-2002 Russell King
 #
-
 OBJCOPYFLAGS	:=-O binary -R .comment -S
 
-ifneq ($(MACHINE),)
-include $(MACHINE)/Makefile.boot
-endif
-
-# Note: the following conditions must always be true:
 #   ZRELADDR == virt_to_phys(PAGE_OFFSET + TEXT_OFFSET)
-#   PARAMS_PHYS must be within 4MB of ZRELADDR
-#   INITRD_PHYS must be in RAM
-ZRELADDR    := $(zreladdr-y)
-PARAMS_PHYS := $(params_phys-y)
-INITRD_PHYS := $(initrd_phys-y)
+ifdef CONFIG_PHYS_OFFSET
+add_hex = $(shell printf 0x%x $$(( $(1) + $(2) )) )
+ZRELADDR    := $(call add_hex, $(CONFIG_PHYS_OFFSET), $(TEXT_OFFSET))
+endif
 
-export ZRELADDR INITRD_PHYS PARAMS_PHYS
+PHYS_OFFSET := $(CONFIG_PHYS_OFFSET)
+export ZRELADDR PARAMS_PHYS PHYS_OFFSET
 
 targets := Image zImage xipImage bootpImage uImage
 
@@ -90,17 +84,10 @@ $(obj)/uImage:	$(obj)/zImage FORCE
 	@$(check_for_multiple_loadaddr)
 	$(call if_changed,uimage)
 
-$(obj)/bootp/bootp: $(obj)/zImage initrd FORCE
+$(obj)/bootp/bootp: $(obj)/zImage FORCE
 	$(Q)$(MAKE) $(build)=$(obj)/bootp $@
 
 $(obj)/bootpImage: $(obj)/bootp/bootp FORCE
 	$(call if_changed,objcopy)
 
-PHONY += initrd
-initrd:
-	@test "$(INITRD_PHYS)" != "" || \
-	(echo This machine does not support INITRD; exit -1)
-	@test "$(INITRD)" != "" || \
-	(echo You must specify INITRD; exit -1)
-
 subdir-	    := bootp compressed dts
diff --git a/arch/arm/boot/bootp/Makefile b/arch/arm/boot/bootp/Makefile
index 981a8d03f064..a2934e6fd89a 100644
--- a/arch/arm/boot/bootp/Makefile
+++ b/arch/arm/boot/bootp/Makefile
@@ -5,9 +5,40 @@
 # This file is included by the global makefile so that you can add your own
 # architecture-specific flags and dependencies.
 #
-
 GCOV_PROFILE	:= n
 
+ifdef PHYS_OFFSET
+add_hex = $(shell printf 0x%x $$(( $(1) + $(2) )) )
+
+# If PHYS_OFFSET is set, INITRD_PHYS and PARAMS_PHYS can be derived,
+# otherwise they must be passed on the command line.
+#
+# Note: the following conditions must always be true:
+#   PARAMS_PHYS must be within 4MB of ZRELADDR
+#   INITRD_PHYS must be in RAM
+
+PARAMS_PHYS := $(call add_hex, $(PHYS_OFFSET), 0x100)
+
+# guess an initrd location if possible
+initrd_offset-$(CONFIG_ARCH_FOOTBRIDGE)	+= 0x00800000
+initrd_offset-$(CONFIG_ARCH_SA1100)	+= 0x00800000
+initrd_offset-$(CONFIG_ARCH_RPC)	+= 0x08000000
+INITRD_OFFSET := $(initrd_offset-y)
+ifdef INITRD_OFFSET
+INITRD_PHYS := $(call add_hex, $(PHYS_OFFSET), $(INITRD_OFFSET))
+endif
+
+endif
+
+PHONY += initrd
+initrd:
+	@test "$(PARAMS_PHYS)" != "" || \
+	(echo bootpImage: You must specify PHYS_OFFSET of PARAMS_PHYS ; exit -1)
+	@test "$(INITRD_PHYS)" != "" || \
+	(echo bootpImage: You must specify INITRD_OFFSET or INITRD_PHYS ; exit -1)
+	@test "$(INITRD)" != "" || \
+	(echo bootpImage: You must specify INITRD; exit -1)
+
 LDFLAGS_bootp	:= --no-undefined -X \
 		 --defsym initrd_phys=$(INITRD_PHYS) \
 		 --defsym params_phys=$(PARAMS_PHYS) -T
@@ -24,6 +55,6 @@ $(obj)/bootp:	$(src)/bootp.lds $(addprefix $(obj)/,init.o kernel.o initrd.o) FOR
 
 $(obj)/kernel.o: arch/arm/boot/zImage FORCE
 
-$(obj)/initrd.o: $(INITRD) FORCE
+$(obj)/initrd.o: initrd $(INITRD) FORCE
 
 PHONY += $(INITRD)
diff --git a/arch/arm/boot/bootp/bootp.lds b/arch/arm/boot/bootp/bootp.lds
index fc54394f4340..160128186bf8 100644
--- a/arch/arm/boot/bootp/bootp.lds
+++ b/arch/arm/boot/bootp/bootp.lds
@@ -1,11 +1,8 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  *  linux/arch/arm/boot/bootp/bootp.lds
  *
  *  Copyright (C) 2000-2002 Russell King
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
  */
 OUTPUT_ARCH(arm)
 ENTRY(_start)
diff --git a/arch/arm/boot/compressed/.gitignore b/arch/arm/boot/compressed/.gitignore
index 60606b0f378d..d32f41778437 100644
--- a/arch/arm/boot/compressed/.gitignore
+++ b/arch/arm/boot/compressed/.gitignore
@@ -1,9 +1,4 @@
 # SPDX-License-Identifier: GPL-2.0-only
-ashldi3.S
-bswapsdi2.S
-font.c
-lib1funcs.S
-hyp-stub.S
 piggy_data
 vmlinux
 vmlinux.lds
diff --git a/arch/arm/boot/compressed/Makefile b/arch/arm/boot/compressed/Makefile
index 91265e7ff672..41bcbb460fac 100644
--- a/arch/arm/boot/compressed/Makefile
+++ b/arch/arm/boot/compressed/Makefile
@@ -13,7 +13,6 @@ ifeq ($(CONFIG_DEBUG_UNCOMPRESS),y)
 OBJS	+= debug.o
 AFLAGS_head.o += -DDEBUG
 endif
-FONTC	= $(srctree)/lib/fonts/font_acorn_8x8.c
 
 # string library code (-Os is enforced to keep it much smaller)
 OBJS		+= string.o
@@ -77,10 +76,10 @@ CPPFLAGS_vmlinux.lds += -DTEXT_OFFSET="$(TEXT_OFFSET)"
 CPPFLAGS_vmlinux.lds += -DMALLOC_SIZE="$(MALLOC_SIZE)"
 
 compress-$(CONFIG_KERNEL_GZIP) = gzip
-compress-$(CONFIG_KERNEL_LZO)  = lzo
-compress-$(CONFIG_KERNEL_LZMA) = lzma
-compress-$(CONFIG_KERNEL_XZ)   = xzkern
-compress-$(CONFIG_KERNEL_LZ4)  = lz4
+compress-$(CONFIG_KERNEL_LZO)  = lzo_with_size
+compress-$(CONFIG_KERNEL_LZMA) = lzma_with_size
+compress-$(CONFIG_KERNEL_XZ)   = xzkern_with_size
+compress-$(CONFIG_KERNEL_LZ4)  = lz4_with_size
 
 libfdt_objs := fdt_rw.o fdt_ro.o fdt_wip.o fdt.o
 
@@ -93,20 +92,15 @@ ifeq ($(CONFIG_USE_OF),y)
 OBJS	+= $(libfdt_objs) fdt_check_mem_start.o
 endif
 
-# -fstack-protector-strong triggers protection checks in this code,
-# but it is being used too early to link to meaningful stack_chk logic.
-$(foreach o, $(libfdt_objs) atags_to_fdt.o fdt_check_mem_start.o, \
-	$(eval CFLAGS_$(o) := -I $(srctree)/scripts/dtc/libfdt -fno-stack-protector))
+OBJS	+= lib1funcs.o ashldi3.o bswapsdi2.o
 
 targets       := vmlinux vmlinux.lds piggy_data piggy.o \
-		 lib1funcs.o ashldi3.o bswapsdi2.o \
 		 head.o $(OBJS)
 
-clean-files += lib1funcs.S ashldi3.S bswapsdi2.S hyp-stub.S
-
 KBUILD_CFLAGS += -DDISABLE_BRANCH_PROFILING
 
 ccflags-y := -fpic $(call cc-option,-mno-single-pic-base,) -fno-builtin \
+	     -I$(srctree)/scripts/dtc/libfdt -fno-stack-protector \
 	     -I$(obj) $(DISABLE_ARM_SSP_PER_TASK_PLUGIN)
 ccflags-remove-$(CONFIG_FUNCTION_TRACER) += -pg
 asflags-y := -DZIMAGE
@@ -134,24 +128,6 @@ endif
 # Next argument is a linker script
 LDFLAGS_vmlinux += -T
 
-# For __aeabi_uidivmod
-lib1funcs = $(obj)/lib1funcs.o
-
-$(obj)/lib1funcs.S: $(srctree)/arch/$(SRCARCH)/lib/lib1funcs.S
-	$(call cmd,shipped)
-
-# For __aeabi_llsl
-ashldi3 = $(obj)/ashldi3.o
-
-$(obj)/ashldi3.S: $(srctree)/arch/$(SRCARCH)/lib/ashldi3.S
-	$(call cmd,shipped)
-
-# For __bswapsi2, __bswapdi2
-bswapsdi2 = $(obj)/bswapsdi2.o
-
-$(obj)/bswapsdi2.S: $(srctree)/arch/$(SRCARCH)/lib/bswapsdi2.S
-	$(call cmd,shipped)
-
 # We need to prevent any GOTOFF relocs being used with references
 # to symbols in the .bss section since we cannot relocate them
 # independently from the rest at run time.  This can be achieved by
@@ -175,8 +151,8 @@ fi
 efi-obj-$(CONFIG_EFI_STUB) := $(objtree)/drivers/firmware/efi/libstub/lib.a
 
 $(obj)/vmlinux: $(obj)/vmlinux.lds $(obj)/$(HEAD) $(obj)/piggy.o \
-		$(addprefix $(obj)/, $(OBJS)) $(lib1funcs) $(ashldi3) \
-		$(bswapsdi2) $(efi-obj-y) FORCE
+		$(addprefix $(obj)/, $(OBJS)) \
+		$(efi-obj-y) FORCE
 	@$(check_for_multiple_zreladdr)
 	$(call if_changed,ld)
 	@$(check_for_bad_syms)
@@ -187,11 +163,4 @@ $(obj)/piggy_data: $(obj)/../Image FORCE
 $(obj)/piggy.o: $(obj)/piggy_data
 
 CFLAGS_font.o := -Dstatic=
-
-$(obj)/font.c: $(FONTC)
-	$(call cmd,shipped)
-
 AFLAGS_hyp-stub.o := -Wa,-march=armv7-a
-
-$(obj)/hyp-stub.S: $(srctree)/arch/$(SRCARCH)/kernel/hyp-stub.S
-	$(call cmd,shipped)
diff --git a/arch/arm/boot/compressed/ashldi3.S b/arch/arm/boot/compressed/ashldi3.S
new file mode 100644
index 000000000000..216f82eda609
--- /dev/null
+++ b/arch/arm/boot/compressed/ashldi3.S
@@ -0,0 +1,3 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/* For __aeabi_llsl */
+#include "../../lib/ashldi3.S"
diff --git a/arch/arm/boot/compressed/bswapsdi2.S b/arch/arm/boot/compressed/bswapsdi2.S
new file mode 100644
index 000000000000..b2156b378c7b
--- /dev/null
+++ b/arch/arm/boot/compressed/bswapsdi2.S
@@ -0,0 +1,3 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/* For __bswapsi2, __bswapdi2 */
+#include "../../lib/bswapsdi2.S"
diff --git a/arch/arm/boot/compressed/efi-header.S b/arch/arm/boot/compressed/efi-header.S
index c0e7a745103e..230030c13085 100644
--- a/arch/arm/boot/compressed/efi-header.S
+++ b/arch/arm/boot/compressed/efi-header.S
@@ -9,16 +9,22 @@
 #include <linux/sizes.h>
 
 		.macro	__nop
-#ifdef CONFIG_EFI_STUB
-		@ This is almost but not quite a NOP, since it does clobber the
-		@ condition flags. But it is the best we can do for EFI, since
-		@ PE/COFF expects the magic string "MZ" at offset 0, while the
-		@ ARM/Linux boot protocol expects an executable instruction
-		@ there.
-		.inst	MZ_MAGIC | (0x1310 << 16)	@ tstne r0, #0x4d000
-#else
  AR_CLASS(	mov	r0, r0		)
   M_CLASS(	nop.w			)
+		.endm
+
+		.macro __initial_nops
+#ifdef CONFIG_EFI_STUB
+		@ This is a two-instruction NOP, which happens to bear the
+		@ PE/COFF signature "MZ" in the first two bytes, so the kernel
+		@ is accepted as an EFI binary. Booting via the UEFI stub
+		@ will not execute those instructions, but the ARM/Linux
+		@ boot protocol does, so we need some NOPs here.
+		.inst	MZ_MAGIC | (0xe225 << 16)	@ eor r5, r5, 0x4d000
+		eor	r5, r5, 0x4d000			@ undo previous insn
+#else
+		__nop
+		__nop
 #endif
 		.endm
 
diff --git a/arch/arm/boot/compressed/font.c b/arch/arm/boot/compressed/font.c
new file mode 100644
index 000000000000..46a677649db4
--- /dev/null
+++ b/arch/arm/boot/compressed/font.c
@@ -0,0 +1,2 @@
+// SPDX-License-Identifier: GPL-2.0-only
+#include "../../../../lib/fonts/font_acorn_8x8.c"
diff --git a/arch/arm/boot/compressed/head.S b/arch/arm/boot/compressed/head.S
index b1cb1972361b..9f406e9c0ea6 100644
--- a/arch/arm/boot/compressed/head.S
+++ b/arch/arm/boot/compressed/head.S
@@ -67,11 +67,7 @@
 #if defined(CONFIG_ARCH_SA1100)
 		.macro	loadsp, rb, tmp1, tmp2
 		mov	\rb, #0x80000000	@ physical base address
-#ifdef CONFIG_DEBUG_LL_SER3
-		add	\rb, \rb, #0x00050000	@ Ser3
-#else
 		add	\rb, \rb, #0x00010000	@ Ser1
-#endif
 		.endm
 #else
 		.macro	loadsp,	rb, tmp1, tmp2
@@ -203,7 +199,8 @@ start:
 		 * were patching the initial instructions of the kernel, i.e
 		 * had started to exploit this "patch area".
 		 */
-		.rept	7
+		__initial_nops
+		.rept	5
 		__nop
 		.endr
 #ifndef CONFIG_THUMB2_KERNEL
diff --git a/arch/arm/boot/compressed/hyp-stub.S b/arch/arm/boot/compressed/hyp-stub.S
new file mode 100644
index 000000000000..a703eaa86f10
--- /dev/null
+++ b/arch/arm/boot/compressed/hyp-stub.S
@@ -0,0 +1,2 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+#include "../../kernel/hyp-stub.S"
diff --git a/arch/arm/boot/compressed/lib1funcs.S b/arch/arm/boot/compressed/lib1funcs.S
new file mode 100644
index 000000000000..815dec73ba4d
--- /dev/null
+++ b/arch/arm/boot/compressed/lib1funcs.S
@@ -0,0 +1,3 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/* For __aeabi_uidivmod */
+#include "../../lib/lib1funcs.S"
diff --git a/arch/arm/boot/compressed/misc-ep93xx.h b/arch/arm/boot/compressed/misc-ep93xx.h
new file mode 100644
index 000000000000..3dc942589cba
--- /dev/null
+++ b/arch/arm/boot/compressed/misc-ep93xx.h
@@ -0,0 +1,86 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Copyright (C) 2006 Lennert Buytenhek <buytenh@wantstofly.org>
+ */
+
+#include <asm/mach-types.h>
+
+static inline unsigned int __raw_readl(unsigned int ptr)
+{
+	return *((volatile unsigned int *)ptr);
+}
+
+static inline void __raw_writeb(unsigned char value, unsigned int ptr)
+{
+	*((volatile unsigned char *)ptr) = value;
+}
+
+static inline void __raw_writel(unsigned int value, unsigned int ptr)
+{
+	*((volatile unsigned int *)ptr) = value;
+}
+
+/*
+ * Some bootloaders don't turn off DMA from the ethernet MAC before
+ * jumping to linux, which means that we might end up with bits of RX
+ * status and packet data scribbled over the uncompressed kernel image.
+ * Work around this by resetting the ethernet MAC before we uncompress.
+ */
+#define PHYS_ETH_SELF_CTL		0x80010020
+#define ETH_SELF_CTL_RESET		0x00000001
+
+static inline void ep93xx_ethernet_reset(void)
+{
+	unsigned int v;
+
+	/* Reset the ethernet MAC.  */
+	v = __raw_readl(PHYS_ETH_SELF_CTL);
+	__raw_writel(v | ETH_SELF_CTL_RESET, PHYS_ETH_SELF_CTL);
+
+	/* Wait for reset to finish.  */
+	while (__raw_readl(PHYS_ETH_SELF_CTL) & ETH_SELF_CTL_RESET)
+		;
+}
+
+#define TS72XX_WDT_CONTROL_PHYS_BASE	0x23800000
+#define TS72XX_WDT_FEED_PHYS_BASE	0x23c00000
+#define TS72XX_WDT_FEED_VAL		0x05
+
+static inline void __maybe_unused ts72xx_watchdog_disable(void)
+{
+	__raw_writeb(TS72XX_WDT_FEED_VAL, TS72XX_WDT_FEED_PHYS_BASE);
+	__raw_writeb(0, TS72XX_WDT_CONTROL_PHYS_BASE);
+}
+
+static inline void ep93xx_decomp_setup(void)
+{
+	if (machine_is_ts72xx())
+		ts72xx_watchdog_disable();
+
+	if (machine_is_adssphere() ||
+	    machine_is_edb9301() ||
+	    machine_is_edb9302() ||
+	    machine_is_edb9302a() ||
+	    machine_is_edb9302a() ||
+	    machine_is_edb9307() ||
+	    machine_is_edb9307a() ||
+	    machine_is_edb9307a() ||
+	    machine_is_edb9312() ||
+	    machine_is_edb9315() ||
+	    machine_is_edb9315a() ||
+	    machine_is_edb9315a() ||
+	    machine_is_gesbc9312() ||
+	    machine_is_micro9() ||
+	    machine_is_micro9l() ||
+	    machine_is_micro9m() ||
+	    machine_is_micro9s() ||
+	    machine_is_micro9m() ||
+	    machine_is_micro9l() ||
+	    machine_is_micro9s() ||
+	    machine_is_sim_one() ||
+	    machine_is_snapper_cl15() ||
+	    machine_is_ts72xx() ||
+	    machine_is_bk3() ||
+	    machine_is_vision_ep9307())
+		ep93xx_ethernet_reset();
+}
diff --git a/arch/arm/boot/compressed/misc.c b/arch/arm/boot/compressed/misc.c
index e1e9a5dde853..abfed1aa2baa 100644
--- a/arch/arm/boot/compressed/misc.c
+++ b/arch/arm/boot/compressed/misc.c
@@ -23,6 +23,9 @@ unsigned int __machine_arch_type;
 #include <linux/types.h>
 #include <linux/linkage.h>
 #include "misc.h"
+#ifdef CONFIG_ARCH_EP93XX
+#include "misc-ep93xx.h"
+#endif
 
 static void putstr(const char *ptr);
 
@@ -128,13 +131,6 @@ asmlinkage void __div0(void)
 	error("Attempting division by 0!");
 }
 
-const unsigned long __stack_chk_guard = 0x000a0dff;
-
-void __stack_chk_fail(void)
-{
-	error("stack-protector: Kernel stack is corrupted\n");
-}
-
 extern int do_decompress(u8 *input, int len, u8 *output, void (*error)(char *x));
 
 
@@ -150,6 +146,9 @@ decompress_kernel(unsigned long output_start, unsigned long free_mem_ptr_p,
 	free_mem_end_ptr	= free_mem_ptr_end_p;
 	__machine_arch_type	= arch_id;
 
+#ifdef CONFIG_ARCH_EP93XX
+	ep93xx_decomp_setup();
+#endif
 	arch_decomp_setup();
 
 	putstr("Uncompressing Linux...");
diff --git a/arch/arm/boot/compressed/vmlinux.lds.S b/arch/arm/boot/compressed/vmlinux.lds.S
index 1bcb68ac4b01..3fcb3e62dc56 100644
--- a/arch/arm/boot/compressed/vmlinux.lds.S
+++ b/arch/arm/boot/compressed/vmlinux.lds.S
@@ -23,6 +23,7 @@ SECTIONS
     *(.ARM.extab*)
     *(.note.*)
     *(.rel.*)
+    *(.printk_index)
     /*
      * Discard any r/w data - this produces a link error if we have any,
      * which is required for PIC decompression.  Local data generates
@@ -57,6 +58,7 @@ SECTIONS
     *(.rodata)
     *(.rodata.*)
     *(.data.rel.ro)
+    *(.data.rel.ro.*)
   }
   .piggydata : {
     *(.piggydata)
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 0de64f237cd8..6aa7dc4db2fc 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -61,6 +61,8 @@ dtb-$(CONFIG_SOC_SAM_V7) += \
 	at91-sama5d2_icp.dtb \
 	at91-sama5d2_ptc_ek.dtb \
 	at91-sama5d2_xplained.dtb \
+	at91-sama5d3_eds.dtb \
+	at91-sama5d3_ksz9477_evb.dtb \
 	at91-sama5d3_xplained.dtb \
 	at91-dvk_som60.dtb \
 	at91-gatwick.dtb \
@@ -78,6 +80,8 @@ dtb-$(CONFIG_SOC_SAM_V7) += \
 	at91-vinco.dtb
 dtb-$(CONFIG_SOC_SAMA7G5) += \
 	at91-sama7g5ek.dtb
+dtb-$(CONFIG_SOC_SP7021) += \
+	sunplus-sp7021-demo-v3.dtb
 dtb-$(CONFIG_ARCH_AXXIA) += \
 	axm5516-amarillo.dtb
 dtb-$(CONFIG_ARCH_BCM2835) += \
@@ -92,6 +96,7 @@ dtb-$(CONFIG_ARCH_BCM2835) += \
 	bcm2837-rpi-3-b.dtb \
 	bcm2837-rpi-3-b-plus.dtb \
 	bcm2837-rpi-cm3-io3.dtb \
+	bcm2837-rpi-zero-2-w.dtb \
 	bcm2711-rpi-400.dtb \
 	bcm2711-rpi-4-b.dtb \
 	bcm2711-rpi-cm4-io.dtb \
@@ -101,6 +106,8 @@ dtb-$(CONFIG_ARCH_BCM_5301X) += \
 	bcm4708-asus-rt-ac56u.dtb \
 	bcm4708-asus-rt-ac68u.dtb \
 	bcm4708-buffalo-wzr-1750dhp.dtb \
+	bcm4708-buffalo-wzr-1166dhp.dtb \
+	bcm4708-buffalo-wzr-1166dhp2.dtb \
 	bcm4708-linksys-ea6300-v1.dtb \
 	bcm4708-linksys-ea6500-v2.dtb \
 	bcm4708-luxul-xap-1510.dtb \
@@ -131,6 +138,7 @@ dtb-$(CONFIG_ARCH_BCM_5301X) += \
 	bcm47094-luxul-xwr-3150-v1.dtb \
 	bcm47094-netgear-r8500.dtb \
 	bcm47094-phicomm-k3.dtb \
+	bcm53015-meraki-mr26.dtb \
 	bcm53016-meraki-mr32.dtb \
 	bcm94708.dtb \
 	bcm94709.dtb \
@@ -142,8 +150,6 @@ dtb-$(CONFIG_ARCH_BCM_53573) += \
 	bcm47189-luxul-xap-810.dtb \
 	bcm47189-tenda-ac9.dtb \
 	bcm947189acdbmr.dtb
-dtb-$(CONFIG_ARCH_BCM_63XX) += \
-	bcm963138dvt.dtb
 dtb-$(CONFIG_ARCH_BCM_CYGNUS) += \
 	bcm911360_entphn.dtb \
 	bcm911360k.dtb \
@@ -177,6 +183,16 @@ dtb-$(CONFIG_ARCH_BERLIN) += \
 	berlin2q-marvell-dmp.dtb
 dtb-$(CONFIG_ARCH_BRCMSTB) += \
 	bcm7445-bcm97445svmb.dtb
+dtb-$(CONFIG_ARCH_BCMBCA) += \
+	bcm947622.dtb \
+	bcm963138.dtb \
+	bcm963138dvt.dtb \
+	bcm963148.dtb \
+	bcm963178.dtb \
+	bcm96756.dtb \
+	bcm96846.dtb \
+	bcm96855.dtb \
+	bcm96878.dtb
 dtb-$(CONFIG_ARCH_CLPS711X) += \
 	ep7211-edb7211.dtb
 dtb-$(CONFIG_ARCH_DAVINCI) += \
@@ -186,6 +202,8 @@ dtb-$(CONFIG_ARCH_DAVINCI) += \
 	da850-lego-ev3.dtb
 dtb-$(CONFIG_ARCH_DIGICOLOR) += \
 	cx92755_equinox.dtb
+dtb-$(CONFIG_ARCH_AIROHA) += \
+	en7523-evb.dtb
 dtb-$(CONFIG_ARCH_EXYNOS3) += \
 	exynos3250-artik5-eval.dtb \
 	exynos3250-monk.dtb \
@@ -220,6 +238,8 @@ dtb-$(CONFIG_ARCH_EXYNOS5) += \
 	exynos5420-arndale-octa.dtb \
 	exynos5420-peach-pit.dtb \
 	exynos5420-smdk5420.dtb \
+	exynos5420-chagall-wifi.dtb \
+	exynos5420-klimt-wifi.dtb \
 	exynos5422-odroidhc1.dtb \
 	exynos5422-odroidxu3.dtb \
 	exynos5422-odroidxu3-lite.dtb \
@@ -249,6 +269,8 @@ dtb-$(CONFIG_ARCH_HISI) += \
 	hi3519-demb.dtb
 dtb-$(CONFIG_ARCH_HIX5HD2) += \
 	hisi-x5hd2-dkb.dtb
+dtb-$(CONFIG_ARCH_HPE_GXP) += \
+	hpe-bmc-dl360gen10.dtb
 dtb-$(CONFIG_ARCH_INTEGRATOR) += \
 	integratorap.dtb \
 	integratorap-im-pd1.dtb \
@@ -263,12 +285,14 @@ dtb-$(CONFIG_ARCH_IXP4XX) += \
 	intel-ixp46x-ixdp465.dtb \
 	intel-ixp42x-adi-coyote.dtb \
 	intel-ixp42x-ixdpg425.dtb \
+	intel-ixp42x-goramo-multilink.dtb \
 	intel-ixp42x-iomega-nas100d.dtb \
 	intel-ixp42x-dlink-dsm-g600.dtb \
 	intel-ixp42x-gateworks-gw2348.dtb \
 	intel-ixp43x-gateworks-gw2358.dtb \
-	intel-ixp42x-netgear-wg302v2.dtb \
-	intel-ixp42x-arcom-vulcan.dtb
+	intel-ixp42x-netgear-wg302v1.dtb \
+	intel-ixp42x-arcom-vulcan.dtb \
+	intel-ixp42x-gateway-7001.dtb
 dtb-$(CONFIG_ARCH_KEYSTONE) += \
 	keystone-k2hk-evm.dtb \
 	keystone-k2l-evm.dtb \
@@ -278,6 +302,7 @@ dtb-$(CONFIG_ARCH_KEYSTONE) += \
 dtb-$(CONFIG_MACH_KIRKWOOD) += \
 	kirkwood-b3.dtb \
 	kirkwood-blackarmor-nas220.dtb \
+	kirkwood-c200-v1.dtb \
 	kirkwood-cloudbox.dtb \
 	kirkwood-d2net.dtb \
 	kirkwood-db-88f6281.dtb \
@@ -449,8 +474,10 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
 	imx6dl-aristainetos_7.dtb \
 	imx6dl-aristainetos2_4.dtb \
 	imx6dl-aristainetos2_7.dtb \
+	imx6dl-colibri-aster.dtb \
 	imx6dl-colibri-eval-v3.dtb \
-	imx6dl-colibri-v1_1-eval-v3.dtb \
+	imx6dl-colibri-iris.dtb \
+	imx6dl-colibri-iris-v2.dtb \
 	imx6dl-cubox-i.dtb \
 	imx6dl-cubox-i-emmc-som-v15.dtb \
 	imx6dl-cubox-i-som-v15.dtb \
@@ -483,6 +510,8 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
 	imx6dl-icore-rqs.dtb \
 	imx6dl-lanmcu.dtb \
 	imx6dl-mamoj.dtb \
+	imx6dl-mba6a.dtb \
+	imx6dl-mba6b.dtb \
 	imx6dl-nit6xlite.dtb \
 	imx6dl-nitrogen6x.dtb \
 	imx6dl-phytec-mira-rdk-nand.dtb \
@@ -531,11 +560,13 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
 	imx6q-apalis-eval.dtb \
 	imx6q-apalis-ixora.dtb \
 	imx6q-apalis-ixora-v1.1.dtb \
+	imx6q-apalis-ixora-v1.2.dtb \
 	imx6q-apf6dev.dtb \
 	imx6q-arm2.dtb \
 	imx6q-b450v3.dtb \
 	imx6q-b650v3.dtb \
 	imx6q-b850v3.dtb \
+	imx6q-bosch-acc.dtb \
 	imx6q-cm-fx6.dtb \
 	imx6q-cubox-i.dtb \
 	imx6q-cubox-i-emmc-som-v15.dtb \
@@ -584,6 +615,8 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
 	imx6q-kp-tpc.dtb \
 	imx6q-logicpd.dtb \
 	imx6q-marsboard.dtb \
+	imx6q-mba6a.dtb \
+	imx6q-mba6b.dtb \
 	imx6q-mccmon6.dtb \
 	imx6q-nitrogen6x.dtb \
 	imx6q-nitrogen6_max.dtb \
@@ -628,7 +661,9 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
 	imx6q-wandboard.dtb \
 	imx6q-wandboard-revb1.dtb \
 	imx6q-wandboard-revd1.dtb \
+	imx6q-yapp4-crux.dtb \
 	imx6q-zii-rdu2.dtb \
+	imx6qp-mba6b.dtb \
 	imx6qp-nitrogen6_max.dtb \
 	imx6qp-nitrogen6_som2.dtb \
 	imx6qp-phytec-mira-rdk-nand.dtb \
@@ -641,6 +676,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
 	imx6qp-tx6qp-8137-mb7.dtb \
 	imx6qp-vicutp.dtb \
 	imx6qp-wandboard-revd1.dtb \
+	imx6qp-yapp4-crux-plus.dtb \
 	imx6qp-zii-rdu2.dtb \
 	imx6s-dhcom-drc02.dtb
 dtb-$(CONFIG_SOC_IMX6SL) += \
@@ -671,9 +707,12 @@ dtb-$(CONFIG_SOC_IMX6UL) += \
 	imx6ul-geam.dtb \
 	imx6ul-isiot-emmc.dtb \
 	imx6ul-isiot-nand.dtb \
-	imx6ul-kontron-n6310-s.dtb \
-	imx6ul-kontron-n6310-s-43.dtb \
+	imx6ul-kontron-bl.dtb \
+	imx6ul-kontron-bl-43.dtb \
 	imx6ul-liteboard.dtb \
+	imx6ul-tqma6ul1-mba6ulx.dtb \
+	imx6ul-tqma6ul2-mba6ulx.dtb \
+	imx6ul-tqma6ul2l-mba6ulx.dtb \
 	imx6ul-opos6uldev.dtb \
 	imx6ul-pico-dwarf.dtb \
 	imx6ul-pico-hobbit.dtb \
@@ -685,21 +724,41 @@ dtb-$(CONFIG_SOC_IMX6UL) += \
 	imx6ul-tx6ul-0011.dtb \
 	imx6ul-tx6ul-mainboard.dtb \
 	imx6ull-14x14-evk.dtb \
+	imx6ull-colibri-aster.dtb \
+	imx6ull-colibri-emmc-aster.dtb \
 	imx6ull-colibri-emmc-eval-v3.dtb \
+	imx6ull-colibri-emmc-iris.dtb \
+	imx6ull-colibri-emmc-iris-v2.dtb \
 	imx6ull-colibri-eval-v3.dtb \
+	imx6ull-colibri-iris.dtb \
+	imx6ull-colibri-iris-v2.dtb \
+	imx6ull-colibri-wifi-aster.dtb \
 	imx6ull-colibri-wifi-eval-v3.dtb \
+	imx6ull-colibri-wifi-iris.dtb \
+	imx6ull-colibri-wifi-iris-v2.dtb \
+	imx6ull-jozacp.dtb \
+	imx6ull-kontron-bl.dtb \
 	imx6ull-myir-mys-6ulx-eval.dtb \
 	imx6ull-opos6uldev.dtb \
 	imx6ull-phytec-segin-ff-rdk-nand.dtb \
 	imx6ull-phytec-segin-ff-rdk-emmc.dtb \
 	imx6ull-phytec-segin-lc-rdk-nand.dtb \
-	imx6ulz-14x14-evk.dtb
+	imx6ull-phytec-tauri-emmc.dtb \
+	imx6ull-phytec-tauri-nand.dtb \
+	imx6ull-tqma6ull2-mba6ulx.dtb \
+	imx6ull-tqma6ull2l-mba6ulx.dtb \
+	imx6ulz-14x14-evk.dtb \
+	imx6ulz-bsh-smm-m2.dtb
 dtb-$(CONFIG_SOC_IMX7D) += \
 	imx7d-cl-som-imx7.dtb \
 	imx7d-colibri-aster.dtb \
 	imx7d-colibri-emmc-aster.dtb \
+	imx7d-colibri-emmc-iris.dtb \
+	imx7d-colibri-emmc-iris-v2.dtb \
 	imx7d-colibri-emmc-eval-v3.dtb \
 	imx7d-colibri-eval-v3.dtb \
+	imx7d-colibri-iris.dtb \
+	imx7d-colibri-iris-v2.dtb \
 	imx7d-flex-concentrator.dtb \
 	imx7d-flex-concentrator-mfg.dtb \
 	imx7d-mba7.dtb \
@@ -714,16 +773,28 @@ dtb-$(CONFIG_SOC_IMX7D) += \
 	imx7d-sdb.dtb \
 	imx7d-sdb-reva.dtb \
 	imx7d-sdb-sht11.dtb \
+	imx7d-smegw01.dtb \
 	imx7d-zii-rmu2.dtb \
 	imx7d-zii-rpu2.dtb \
 	imx7s-colibri-aster.dtb \
 	imx7s-colibri-eval-v3.dtb \
+	imx7s-colibri-iris.dtb \
+	imx7s-colibri-iris-v2.dtb \
 	imx7s-mba7.dtb \
 	imx7s-warp.dtb
 dtb-$(CONFIG_SOC_IMX7ULP) += \
 	imx7ulp-com.dtb \
 	imx7ulp-evk.dtb
+dtb-$(CONFIG_SOC_IMXRT) += \
+	imxrt1050-evk.dtb
+dtb-$(CONFIG_SOC_LAN966) += \
+	lan966x-kontron-kswitch-d10-mmt-6g-2gs.dtb \
+	lan966x-kontron-kswitch-d10-mmt-8g.dtb \
+	lan966x-pcb8290.dtb \
+	lan966x-pcb8291.dtb \
+	lan966x-pcb8309.dtb
 dtb-$(CONFIG_SOC_LS1021A) += \
+	ls1021a-iot.dtb \
 	ls1021a-moxa-uc-8410a.dtb \
 	ls1021a-qds.dtb \
 	ls1021a-tsn.dtb \
@@ -794,6 +865,7 @@ dtb-$(CONFIG_ARCH_OMAP3) += \
 	logicpd-som-lv-37xx-devkit.dtb \
 	omap3430-sdp.dtb \
 	omap3-beagle.dtb \
+	omap3-beagle-ab4.dtb \
 	omap3-beagle-xm.dtb \
 	omap3-beagle-xm-ab.dtb \
 	omap3-cm-t3517.dtb \
@@ -882,6 +954,7 @@ dtb-$(CONFIG_SOC_AM33XX) += \
 	am335x-regor-rdk.dtb \
 	am335x-sancloud-bbe.dtb \
 	am335x-sancloud-bbe-lite.dtb \
+	am335x-sancloud-bbe-extended-wifi.dtb \
 	am335x-shc.dtb \
 	am335x-sbc-t335.dtb \
 	am335x-sl50.dtb \
@@ -954,11 +1027,13 @@ dtb-$(CONFIG_ARCH_OXNAS) += \
 	ox810se-wd-mbwe.dtb \
 	ox820-cloudengines-pogoplug-series-3.dtb
 dtb-$(CONFIG_ARCH_QCOM) += \
+	qcom-apq8016-sbc.dtb \
+	qcom-apq8026-asus-sparrow.dtb \
 	qcom-apq8026-lg-lenok.dtb \
 	qcom-apq8060-dragonboard.dtb \
 	qcom-apq8064-cm-qs600.dtb \
 	qcom-apq8064-ifc6410.dtb \
-	qcom-apq8064-sony-xperia-yuga.dtb \
+	qcom-apq8064-sony-xperia-lagan-yuga.dtb \
 	qcom-apq8064-asus-nexus7-flo.dtb \
 	qcom-apq8074-dragonboard.dtb \
 	qcom-apq8084-ifc6540.dtb \
@@ -975,18 +1050,22 @@ dtb-$(CONFIG_ARCH_QCOM) += \
 	qcom-ipq8064-rb3011.dtb \
 	qcom-msm8226-samsung-s3ve3g.dtb \
 	qcom-msm8660-surf.dtb \
+	qcom-msm8916-samsung-e5.dtb \
+	qcom-msm8916-samsung-e7.dtb \
+	qcom-msm8916-samsung-grandmax.dtb \
 	qcom-msm8916-samsung-serranove.dtb \
 	qcom-msm8960-cdp.dtb \
-	qcom-msm8974-fairphone-fp2.dtb \
 	qcom-msm8974-lge-nexus5-hammerhead.dtb \
-	qcom-msm8974-samsung-klte.dtb \
-	qcom-msm8974-sony-xperia-amami.dtb \
-	qcom-msm8974-sony-xperia-castor.dtb \
-	qcom-msm8974-sony-xperia-honami.dtb \
+	qcom-msm8974-sony-xperia-rhine-amami.dtb \
+	qcom-msm8974-sony-xperia-rhine-honami.dtb \
+	qcom-msm8974pro-fairphone-fp2.dtb \
+	qcom-msm8974pro-samsung-klte.dtb \
+	qcom-msm8974pro-sony-xperia-shinano-castor.dtb \
 	qcom-mdm9615-wp8548-mangoh-green.dtb \
 	qcom-sdx55-mtp.dtb \
 	qcom-sdx55-t55.dtb \
-	qcom-sdx55-telit-fn980-tlb.dtb
+	qcom-sdx55-telit-fn980-tlb.dtb \
+	qcom-sdx65-mtp.dtb
 dtb-$(CONFIG_ARCH_RDA) += \
 	rda8810pl-orangepi-2g-iot.dtb \
 	rda8810pl-orangepi-i96.dtb
@@ -1092,7 +1171,7 @@ dtb-$(CONFIG_ARCH_S5PV210) += \
 	s5pv210-torbreck.dtb
 dtb-$(CONFIG_ARCH_INTEL_SOCFPGA) += \
 	socfpga_arria5_socdk.dtb \
-	socfpga_arria10_mercury_aa1.dtb \
+	socfpga_arria10_chameleonv3.dtb \
 	socfpga_arria10_socdk_nand.dtb \
 	socfpga_arria10_socdk_qspi.dtb \
 	socfpga_arria10_socdk_sdmmc.dtb \
@@ -1132,21 +1211,31 @@ dtb-$(CONFIG_ARCH_STM32) += \
 	stm32h743i-disco.dtb \
 	stm32h750i-art-pi.dtb \
 	stm32mp135f-dk.dtb \
+	stm32mp151a-prtt1a.dtb \
+	stm32mp151a-prtt1c.dtb \
+	stm32mp151a-prtt1s.dtb \
 	stm32mp153c-dhcom-drc02.dtb \
+	stm32mp153c-dhcor-drc-compact.dtb \
 	stm32mp157a-avenger96.dtb \
 	stm32mp157a-dhcor-avenger96.dtb \
 	stm32mp157a-dk1.dtb \
+	stm32mp157a-dk1-scmi.dtb \
 	stm32mp157a-iot-box.dtb \
 	stm32mp157a-microgea-stm32mp1-microdev2.0.dtb \
 	stm32mp157a-microgea-stm32mp1-microdev2.0-of7.dtb \
 	stm32mp157a-icore-stm32mp1-ctouch2.dtb \
+	stm32mp157a-icore-stm32mp1-ctouch2-of10.dtb \
 	stm32mp157a-icore-stm32mp1-edimm2.2.dtb \
 	stm32mp157a-stinger96.dtb \
 	stm32mp157c-dhcom-pdk2.dtb \
 	stm32mp157c-dhcom-picoitx.dtb \
 	stm32mp157c-dk2.dtb \
+	stm32mp157c-dk2-scmi.dtb \
 	stm32mp157c-ed1.dtb \
+	stm32mp157c-ed1-scmi.dtb \
+	stm32mp157c-emsbc-argon.dtb \
 	stm32mp157c-ev1.dtb \
+	stm32mp157c-ev1-scmi.dtb \
 	stm32mp157c-lxa-mc1.dtb \
 	stm32mp157c-odyssey.dtb
 dtb-$(CONFIG_MACH_SUN4I) += \
@@ -1213,6 +1302,7 @@ dtb-$(CONFIG_MACH_SUN7I) += \
 	sun7i-a20-bananapro.dtb \
 	sun7i-a20-cubieboard2.dtb \
 	sun7i-a20-cubietruck.dtb \
+	sun7i-a20-haoyu-marsboard.dtb \
 	sun7i-a20-hummingbird.dtb \
 	sun7i-a20-itead-ibox.dtb \
 	sun7i-a20-i12-tvbox.dtb \
@@ -1304,6 +1394,7 @@ dtb-$(CONFIG_MACH_SUNIV) += \
 	suniv-f1c100s-licheepi-nano.dtb
 dtb-$(CONFIG_ARCH_TEGRA_2x_SOC) += \
 	tegra20-acer-a500-picasso.dtb \
+	tegra20-asus-tf101.dtb \
 	tegra20-harmony.dtb \
 	tegra20-colibri-eval-v3.dtb \
 	tegra20-colibri-iris.dtb \
@@ -1320,12 +1411,18 @@ dtb-$(CONFIG_ARCH_TEGRA_3x_SOC) += \
 	tegra30-asus-nexus7-grouper-PM269.dtb \
 	tegra30-asus-nexus7-grouper-E1565.dtb \
 	tegra30-asus-nexus7-tilapia-E1565.dtb \
+	tegra30-asus-tf201.dtb \
+	tegra30-asus-tf300t.dtb \
+	tegra30-asus-tf300tg.dtb \
+	tegra30-asus-tf700t.dtb \
 	tegra30-beaver.dtb \
 	tegra30-cardhu-a02.dtb \
 	tegra30-cardhu-a04.dtb \
 	tegra30-colibri-eval-v3.dtb \
-	tegra30-ouya.dtb
+	tegra30-ouya.dtb \
+	tegra30-pegatron-chagall.dtb
 dtb-$(CONFIG_ARCH_TEGRA_114_SOC) += \
+	tegra114-asus-tf701t.dtb \
 	tegra114-dalmore.dtb \
 	tegra114-roth.dtb \
 	tegra114-tn7.dtb
@@ -1334,6 +1431,7 @@ dtb-$(CONFIG_ARCH_TEGRA_124_SOC) += \
 	tegra124-apalis-v1.2-eval.dtb \
 	tegra124-jetson-tk1.dtb \
 	tegra124-nyan-big.dtb \
+	tegra124-nyan-big-fhd.dtb \
 	tegra124-nyan-blaze.dtb \
 	tegra124-venice2.dtb
 dtb-$(CONFIG_ARCH_U8500) += \
@@ -1347,6 +1445,7 @@ dtb-$(CONFIG_ARCH_U8500) += \
 	ste-ux500-samsung-janice.dtb \
 	ste-ux500-samsung-gavini.dtb \
 	ste-ux500-samsung-codina.dtb \
+	ste-ux500-samsung-codina-tmo.dtb \
 	ste-ux500-samsung-skomer.dtb \
 	ste-ux500-samsung-kyle.dtb
 dtb-$(CONFIG_ARCH_UNIPHIER) += \
@@ -1392,6 +1491,7 @@ dtb-$(CONFIG_ARCH_ZYNQ) += \
 	zynq-zybo.dtb \
 	zynq-zybo-z7.dtb
 dtb-$(CONFIG_MACH_ARMADA_370) += \
+	armada-370-c200-v2.dtb \
 	armada-370-db.dtb \
 	armada-370-dlink-dns327l.dtb \
 	armada-370-mirabox.dtb \
@@ -1457,6 +1557,7 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += \
 	mt2701-evb.dtb \
 	mt6580-evbp1.dtb \
 	mt6589-aquaris5.dtb \
+	mt6589-fairphone-fp1.dtb \
 	mt6592-evb.dtb \
 	mt7623a-rfb-emmc.dtb \
 	mt7623a-rfb-nand.dtb \
@@ -1468,6 +1569,9 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += \
 dtb-$(CONFIG_ARCH_MILBEAUT) += milbeaut-m10v-evb.dtb
 dtb-$(CONFIG_ARCH_MSTARV7) += \
 	mstar-infinity-msc313-breadbee_crust.dtb \
+	mstar-infinity2m-ssd202d-100ask-dongshanpione.dtb \
+	mstar-infinity2m-ssd202d-miyoo-mini.dtb \
+	mstar-infinity2m-ssd202d-wirelesstag-ido-sbc2d06-v1b-22w.dtb \
 	mstar-infinity2m-ssd202d-ssd201htv2.dtb \
 	mstar-infinity2m-ssd202d-unitv2.dtb \
 	mstar-infinity3-msc313e-breadbee.dtb \
@@ -1476,12 +1580,15 @@ dtb-$(CONFIG_ARCH_ASPEED) += \
 	aspeed-ast2500-evb.dtb \
 	aspeed-ast2600-evb-a1.dtb \
 	aspeed-ast2600-evb.dtb \
+	aspeed-bmc-amd-daytonax.dtb \
 	aspeed-bmc-amd-ethanolx.dtb \
 	aspeed-bmc-ampere-mtjade.dtb \
-	aspeed-bmc-arm-centriq2400-rep.dtb \
+	aspeed-bmc-ampere-mtmitchell.dtb \
 	aspeed-bmc-arm-stardragon4800-rep2.dtb \
 	aspeed-bmc-asrock-e3c246d4i.dtb \
+	aspeed-bmc-asrock-romed8hm3.dtb \
 	aspeed-bmc-bytedance-g220a.dtb \
+	aspeed-bmc-facebook-bletchley.dtb \
 	aspeed-bmc-facebook-cloudripper.dtb \
 	aspeed-bmc-facebook-cmm.dtb \
 	aspeed-bmc-facebook-elbert.dtb \
@@ -1516,7 +1623,13 @@ dtb-$(CONFIG_ARCH_ASPEED) += \
 	aspeed-bmc-opp-witherspoon.dtb \
 	aspeed-bmc-opp-zaius.dtb \
 	aspeed-bmc-portwell-neptune.dtb \
+	aspeed-bmc-qcom-dc-scm-v1.dtb \
 	aspeed-bmc-quanta-q71l.dtb \
+	aspeed-bmc-quanta-s6q.dtb \
 	aspeed-bmc-supermicro-x11spi.dtb \
 	aspeed-bmc-inventec-transformers.dtb \
-	aspeed-bmc-tyan-s7106.dtb
+	aspeed-bmc-tyan-s7106.dtb \
+	aspeed-bmc-tyan-s8036.dtb \
+	aspeed-bmc-vegman-n110.dtb \
+	aspeed-bmc-vegman-rx20.dtb \
+	aspeed-bmc-vegman-sx20.dtb
diff --git a/arch/arm/boot/dts/alpine.dtsi b/arch/arm/boot/dts/alpine.dtsi
index 3b0675a1c460..4be9887033f9 100644
--- a/arch/arm/boot/dts/alpine.dtsi
+++ b/arch/arm/boot/dts/alpine.dtsi
@@ -154,7 +154,7 @@
 			reg = <0x0 0xfbc00000 0x0 0x100000>;
 			interrupt-map-mask = <0xf800 0 0 7>;
 			/* Add legacy interrupts for SATA devices only */
-			interrupt-map =	<0x4000 0 0 1 &gic 0 43 4>,
+			interrupt-map = <0x4000 0 0 1 &gic 0 43 4>,
 					<0x4800 0 0 1 &gic 0 44 4>;
 
 			/* 32 bit non prefetchable memory space */
diff --git a/arch/arm/boot/dts/am335x-baltos-ir2110.dts b/arch/arm/boot/dts/am335x-baltos-ir2110.dts
index daf4cb398070..75992eec830f 100644
--- a/arch/arm/boot/dts/am335x-baltos-ir2110.dts
+++ b/arch/arm/boot/dts/am335x-baltos-ir2110.dts
@@ -81,3 +81,147 @@
 	pinctrl-0 = <&mmc1_pins>;
 	cd-gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
 };
+
+&gpio0 {
+	gpio-line-names =
+		"MDIO",
+		"MDC",
+		"NC",
+		"NC",
+		"I2C1_SDA",
+		"I2C1_SCL",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"UART1_CTSN",
+		"UART1_RTSN",
+		"UART1_RX",
+		"UART1_TX",
+		"onrisc:blue:wlan",
+		"onrisc:green:app",
+		"USB0_DRVVBUS",
+		"ETH2_INT",
+		"NC",
+		"RMII1_TXD1",
+		"MMC1_DAT0",
+		"MMC1_DAT1",
+		"NC",
+		"NC",
+		"MMC1_DAT2",
+		"MMC1_DAT3",
+		"RMII1_TXD0",
+		"NC",
+		"GPMC_WAIT0",
+		"GPMC_WP_N";
+};
+
+&gpio1 {
+	gpio-line-names =
+		"GPMC_AD0",
+		"GPMC_AD1",
+		"GPMC_AD2",
+		"GPMC_AD3",
+		"GPMC_AD4",
+		"GPMC_AD5",
+		"GPMC_AD6",
+		"GPMC_AD7",
+		"NC",
+		"NC",
+		"CONSOLE_RX",
+		"CONSOLE_TX",
+		"NC",
+		"NC",
+		"NC",
+		"SD_CD",
+		"RGMII2_TCTL",
+		"RGMII2_RCTL",
+		"RGMII2_TD3",
+		"RGMII2_TD2",
+		"RGMII2_TD1",
+		"RGMII2_TD0",
+		"RGMII2_TCLK",
+		"RGMII2_RCLK",
+		"RGMII2_RD3",
+		"RGMII2_RD2",
+		"RGMII2_RD1",
+		"RGMII2_RD0",
+		"PMIC_INT1",
+		"GPMC_CSN0_Flash",
+		"MMC1_CLK",
+		"MMC1_CMD";
+};
+
+&gpio2 {
+	gpio-line-names =
+		"GPMC_CSN3_BUS",
+		"GPMC_CLK",
+		"GPMC_ADVN_ALE",
+		"GPMC_OEN_RE_N",
+		"GPMC_WE_N",
+		"GPMC_BEN0_CLE",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"SW2_0",
+		"SW2_1",
+		"RMII1_RXD1",
+		"RMII1_RXD0",
+		"UART1_DTR",
+		"UART1_DSR",
+		"UART1_DCD",
+		"UART1_RI",
+		"MMC0_DAT3",
+		"MMC0_DAT2",
+		"MMC0_DAT1",
+		"MMC0_DAT0",
+		"MMC0_CLK",
+		"MMC0_CMD";
+};
+
+&gpio3 {
+	gpio-line-names =
+		"onrisc:red:power",
+		"RMII1_CRS_DV",
+		"RMII1_RXER",
+		"RMII1_TXEN",
+		"NC",
+		"NC",
+		"NC",
+		"WLAN_IRQ",
+		"WLAN_EN",
+		"SW2_2",
+		"SW2_3",
+		"NC",
+		"NC",
+		"NC",
+		"ModeA0",
+		"ModeA1",
+		"ModeA2",
+		"ModeA3",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC";
+};
diff --git a/arch/arm/boot/dts/am335x-baltos-ir3220.dts b/arch/arm/boot/dts/am335x-baltos-ir3220.dts
index 2123bd589484..087e084506d2 100644
--- a/arch/arm/boot/dts/am335x-baltos-ir3220.dts
+++ b/arch/arm/boot/dts/am335x-baltos-ir3220.dts
@@ -91,6 +91,10 @@
 		interrupts = <20 IRQ_TYPE_EDGE_RISING>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&tca6416_pins>;
+		gpio-line-names = "GP_IN0", "GP_IN1", "GP_IN2", "GP_IN3",
+				  "GP_OUT0", "GP_OUT1", "GP_OUT2", "GP_OUT3",
+				  "ModeA0", "ModeA1", "ModeA2", "ModeA3",
+				  "ModeB0", "ModeB1", "ModeB2", "ModeB3";
 	};
 };
 
@@ -123,3 +127,147 @@
 	pinctrl-0 = <&mmc1_pins>;
 	cd-gpios = <&gpio2 18 GPIO_ACTIVE_LOW>;
 };
+
+&gpio0 {
+	gpio-line-names =
+		"MDIO",
+		"MDC",
+		"UART2_RX",
+		"UART2_TX",
+		"I2C1_SDA",
+		"I2C1_SCL",
+		"WLAN_BTN",
+		"W_DISABLE",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"UART1_CTSN",
+		"UART1_RTSN",
+		"UART1_RX",
+		"UART1_TX",
+		"onrisc:blue:wlan",
+		"onrisc:green:app",
+		"USB0_DRVVBUS",
+		"ETH2_INT",
+		"TCA6416_INT",
+		"RMII1_TXD1",
+		"MMC1_DAT0",
+		"MMC1_DAT1",
+		"NC",
+		"NC",
+		"MMC1_DAT2",
+		"MMC1_DAT3",
+		"RMII1_TXD0",
+		"NC",
+		"GPMC_WAIT0",
+		"GPMC_WP_N";
+};
+
+&gpio1 {
+	gpio-line-names =
+		"GPMC_AD0",
+		"GPMC_AD1",
+		"GPMC_AD2",
+		"GPMC_AD3",
+		"GPMC_AD4",
+		"GPMC_AD5",
+		"GPMC_AD6",
+		"GPMC_AD7",
+		"NC",
+		"NC",
+		"CONSOLE_RX",
+		"CONSOLE_TX",
+		"UART2_DTR",
+		"UART2_DSR",
+		"UART2_DCD",
+		"UART2_RI",
+		"RGMII2_TCTL",
+		"RGMII2_RCTL",
+		"RGMII2_TD3",
+		"RGMII2_TD2",
+		"RGMII2_TD1",
+		"RGMII2_TD0",
+		"RGMII2_TCLK",
+		"RGMII2_RCLK",
+		"RGMII2_RD3",
+		"RGMII2_RD2",
+		"RGMII2_RD1",
+		"RGMII2_RD0",
+		"PMIC_INT1",
+		"GPMC_CSN0_Flash",
+		"MMC1_CLK",
+		"MMC1_CMD";
+};
+
+&gpio2 {
+	gpio-line-names =
+		"GPMC_CSN3_BUS",
+		"GPMC_CLK",
+		"GPMC_ADVN_ALE",
+		"GPMC_OEN_RE_N",
+		"GPMC_WE_N",
+		"GPMC_BEN0_CLE",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"SD_CD",
+		"SD_WP",
+		"RMII1_RXD1",
+		"RMII1_RXD0",
+		"UART1_DTR",
+		"UART1_DSR",
+		"UART1_DCD",
+		"UART1_RI",
+		"MMC0_DAT3",
+		"MMC0_DAT2",
+		"MMC0_DAT1",
+		"MMC0_DAT0",
+		"MMC0_CLK",
+		"MMC0_CMD";
+};
+
+&gpio3 {
+	gpio-line-names =
+		"onrisc:red:power",
+		"RMII1_CRS_DV",
+		"RMII1_RXER",
+		"RMII1_TXEN",
+		"3G_PWR_EN",
+		"UART2_CTSN",
+		"UART2_RTSN",
+		"WLAN_IRQ",
+		"WLAN_EN",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"USB1_DRVVBUS",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC";
+};
diff --git a/arch/arm/boot/dts/am335x-baltos-ir5221.dts b/arch/arm/boot/dts/am335x-baltos-ir5221.dts
index 2f3872dbf4f4..faeb39aab60a 100644
--- a/arch/arm/boot/dts/am335x-baltos-ir5221.dts
+++ b/arch/arm/boot/dts/am335x-baltos-ir5221.dts
@@ -99,6 +99,10 @@
 		interrupts = <20 IRQ_TYPE_EDGE_RISING>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&tca6416_pins>;
+		gpio-line-names = "GP_IN0", "GP_IN1", "GP_IN2", "GP_IN3",
+				  "GP_OUT0", "GP_OUT1", "GP_OUT2", "GP_OUT3",
+				  "ModeA0", "ModeA1", "ModeA2", "ModeA3",
+				  "ModeB0", "ModeB1", "ModeB2", "ModeB3";
 	};
 };
 
@@ -147,3 +151,147 @@
 	pinctrl-0 = <&mmc1_pins>;
 	cd-gpios = <&gpio2 18 GPIO_ACTIVE_LOW>;
 };
+
+&gpio0 {
+	gpio-line-names =
+		"MDIO",
+		"MDC",
+		"UART2_RX",
+		"UART2_TX",
+		"I2C1_SDA",
+		"I2C1_SCL",
+		"WLAN_BTN",
+		"W_DISABLE",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"UART1_CTSN",
+		"UART1_RTSN",
+		"UART1_RX",
+		"UART1_TX",
+		"onrisc:blue:wlan",
+		"onrisc:green:app",
+		"USB0_DRVVBUS",
+		"ETH2_INT",
+		"TCA6416_INT",
+		"RMII1_TXD1",
+		"MMC1_DAT0",
+		"MMC1_DAT1",
+		"NC",
+		"NC",
+		"MMC1_DAT2",
+		"MMC1_DAT3",
+		"RMII1_TXD0",
+		"NC",
+		"GPMC_WAIT0",
+		"GPMC_WP_N";
+};
+
+&gpio1 {
+	gpio-line-names =
+		"GPMC_AD0",
+		"GPMC_AD1",
+		"GPMC_AD2",
+		"GPMC_AD3",
+		"GPMC_AD4",
+		"GPMC_AD5",
+		"GPMC_AD6",
+		"GPMC_AD7",
+		"DCAN1_TX",
+		"DCAN1_RX",
+		"CONSOLE_RX",
+		"CONSOLE_TX",
+		"UART2_DTR",
+		"UART2_DSR",
+		"UART2_DCD",
+		"UART2_RI",
+		"RGMII2_TCTL",
+		"RGMII2_RCTL",
+		"RGMII2_TD3",
+		"RGMII2_TD2",
+		"RGMII2_TD1",
+		"RGMII2_TD0",
+		"RGMII2_TCLK",
+		"RGMII2_RCLK",
+		"RGMII2_RD3",
+		"RGMII2_RD2",
+		"RGMII2_RD1",
+		"RGMII2_RD0",
+		"PMIC_INT1",
+		"GPMC_CSN0_Flash",
+		"MMC1_CLK",
+		"MMC1_CMD";
+};
+
+&gpio2 {
+	gpio-line-names =
+		"GPMC_CSN3_BUS",
+		"GPMC_CLK",
+		"GPMC_ADVN_ALE",
+		"GPMC_OEN_RE_N",
+		"GPMC_WE_N",
+		"GPMC_BEN0_CLE",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"SD_CD",
+		"SD_WP",
+		"RMII1_RXD1",
+		"RMII1_RXD0",
+		"UART1_DTR",
+		"UART1_DSR",
+		"UART1_DCD",
+		"UART1_RI",
+		"MMC0_DAT3",
+		"MMC0_DAT2",
+		"MMC0_DAT1",
+		"MMC0_DAT0",
+		"MMC0_CLK",
+		"MMC0_CMD";
+};
+
+&gpio3 {
+	gpio-line-names =
+		"onrisc:red:power",
+		"RMII1_CRS_DV",
+		"RMII1_RXER",
+		"RMII1_TXEN",
+		"3G_PWR_EN",
+		"UART2_CTSN",
+		"UART2_RTSN",
+		"WLAN_IRQ",
+		"WLAN_EN",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"USB1_DRVVBUS",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC";
+};
diff --git a/arch/arm/boot/dts/am335x-baltos.dtsi b/arch/arm/boot/dts/am335x-baltos.dtsi
index 366702630290..6161c8929a78 100644
--- a/arch/arm/boot/dts/am335x-baltos.dtsi
+++ b/arch/arm/boot/dts/am335x-baltos.dtsi
@@ -197,7 +197,7 @@
 		rb-gpios = <&gpmc 0 GPIO_ACTIVE_HIGH>; /* gpmc_wait0 */
 		nand-bus-width = <8>;
 		ti,nand-ecc-opt = "bch8";
-		ti,nand-xfer-type = "polled";
+		ti,nand-xfer-type = "prefetch-dma";
 
 		gpmc,device-nand = "true";
 		gpmc,device-width = <1>;
@@ -285,7 +285,7 @@
 			/* VDD_MPU voltage limits 0.95V - 1.26V with +/-4% tolerance */
 			regulator-name = "vdd_mpu";
 			regulator-min-microvolt = <912500>;
-			regulator-max-microvolt = <1312500>;
+			regulator-max-microvolt = <1351500>;
 			regulator-boot-on;
 			regulator-always-on;
 		};
diff --git a/arch/arm/boot/dts/am335x-bone-common.dtsi b/arch/arm/boot/dts/am335x-bone-common.dtsi
index 0ccdc7cd463b..02e04a12a270 100644
--- a/arch/arm/boot/dts/am335x-bone-common.dtsi
+++ b/arch/arm/boot/dts/am335x-bone-common.dtsi
@@ -399,8 +399,13 @@
 &rtc {
 	clocks = <&clk_32768_ck>, <&clk_24mhz_clkctrl AM3_CLK_24MHZ_CLKDIV32K_CLKCTRL 0>;
 	clock-names = "ext-clk", "int-clk";
+	system-power-controller;
 };
 
 &pruss_tm {
 	status = "okay";
 };
+
+&wkup_m3_ipc {
+	firmware-name = "am335x-bone-scale-data.bin";
+};
diff --git a/arch/arm/boot/dts/am335x-boneblack-common.dtsi b/arch/arm/boot/dts/am335x-boneblack-common.dtsi
index 10494c4431b9..a7a8c61ef9b2 100644
--- a/arch/arm/boot/dts/am335x-boneblack-common.dtsi
+++ b/arch/arm/boot/dts/am335x-boneblack-common.dtsi
@@ -22,10 +22,6 @@
 	non-removable;
 };
 
-&rtc {
-	system-power-controller;
-};
-
 / {
 	memory@80000000 {
 		device_type = "memory";
diff --git a/arch/arm/boot/dts/am335x-boneblack-wireless.dts b/arch/arm/boot/dts/am335x-boneblack-wireless.dts
index c72b09ab8da0..207d2b63e0eb 100644
--- a/arch/arm/boot/dts/am335x-boneblack-wireless.dts
+++ b/arch/arm/boot/dts/am335x-boneblack-wireless.dts
@@ -19,7 +19,7 @@
 		regulator-name = "wlan-en-regulator";
 		regulator-min-microvolt = <1800000>;
 		regulator-max-microvolt = <1800000>;
-		startup-delay-us= <70000>;
+		startup-delay-us = <70000>;
 
 		/* WL_EN */
 		gpio = <&gpio3 9 0>;
diff --git a/arch/arm/boot/dts/am335x-boneblack.dts b/arch/arm/boot/dts/am335x-boneblack.dts
index 9312197316f0..b956e2f60fe0 100644
--- a/arch/arm/boot/dts/am335x-boneblack.dts
+++ b/arch/arm/boot/dts/am335x-boneblack.dts
@@ -168,3 +168,7 @@
 		"NC",
 		"NC";
 };
+
+&baseboard_eeprom {
+	vcc-supply = <&ldo4_reg>;
+};
diff --git a/arch/arm/boot/dts/am335x-boneblue.dts b/arch/arm/boot/dts/am335x-boneblue.dts
index c6bb325ead33..34579e98636e 100644
--- a/arch/arm/boot/dts/am335x-boneblue.dts
+++ b/arch/arm/boot/dts/am335x-boneblue.dts
@@ -106,7 +106,7 @@
 		regulator-name = "wlan-en-regulator";
 		regulator-min-microvolt = <1800000>;
 		regulator-max-microvolt = <1800000>;
-		startup-delay-us= <70000>;
+		startup-delay-us = <70000>;
 
 		/* WL_EN */
 		gpio = <&gpio3 9 0>;
@@ -341,7 +341,7 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 			ax8975@c {
-				compatible = "ak,ak8975";
+				compatible = "asahi-kasei,ak8975";
 				reg = <0x0c>;
 			};
 		};
diff --git a/arch/arm/boot/dts/am335x-bonegreen-wireless.dts b/arch/arm/boot/dts/am335x-bonegreen-wireless.dts
index 215f279e476b..d388cffa1a4d 100644
--- a/arch/arm/boot/dts/am335x-bonegreen-wireless.dts
+++ b/arch/arm/boot/dts/am335x-bonegreen-wireless.dts
@@ -18,7 +18,7 @@
 		regulator-name = "wlan-en-regulator";
 		regulator-min-microvolt = <1800000>;
 		regulator-max-microvolt = <1800000>;
-		startup-delay-us= <70000>;
+		startup-delay-us = <70000>;
 
 		/* WL_EN */
 		gpio = <&gpio0 26 0>;
diff --git a/arch/arm/boot/dts/am335x-cm-t335.dts b/arch/arm/boot/dts/am335x-cm-t335.dts
index d9f003d886bf..993b13420699 100644
--- a/arch/arm/boot/dts/am335x-cm-t335.dts
+++ b/arch/arm/boot/dts/am335x-cm-t335.dts
@@ -325,7 +325,7 @@ status = "okay";
 	tlv320aic23: codec@1a {
 		compatible = "ti,tlv320aic23";
 		reg = <0x1a>;
-		#sound-dai-cells= <0>;
+		#sound-dai-cells = <0>;
 		status = "okay";
 	};
 };
@@ -491,7 +491,7 @@ status = "okay";
 		tx-num-evt = <1>;
 		rx-num-evt = <1>;
 
-		#sound-dai-cells= <0>;
+		#sound-dai-cells = <0>;
 		status = "okay";
 };
 
diff --git a/arch/arm/boot/dts/am335x-evm.dts b/arch/arm/boot/dts/am335x-evm.dts
index 659e99eabe66..25c6ac9913d2 100644
--- a/arch/arm/boot/dts/am335x-evm.dts
+++ b/arch/arm/boot/dts/am335x-evm.dts
@@ -92,20 +92,18 @@
 				0x0201006c>;	/* DOWN */
 	};
 
-	gpio_keys: volume_keys0 {
+	gpio_keys: volume-keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		autorepeat;
 
-		switch9 {
+		switch-9 {
 			label = "volume-up";
 			linux,code = <115>;
 			gpios = <&gpio0 2 GPIO_ACTIVE_LOW>;
 			wakeup-source;
 		};
 
-		switch10 {
+		switch-10 {
 			label = "volume-down";
 			linux,code = <114>;
 			gpios = <&gpio0 3 GPIO_ACTIVE_LOW>;
@@ -782,3 +780,7 @@
 &pruss_tm {
 	status = "okay";
 };
+
+&wkup_m3_ipc {
+	firmware-name = "am335x-evm-scale-data.bin";
+};
diff --git a/arch/arm/boot/dts/am335x-evmsk.dts b/arch/arm/boot/dts/am335x-evmsk.dts
index a2db65538e51..9c458e5a95b7 100644
--- a/arch/arm/boot/dts/am335x-evmsk.dts
+++ b/arch/arm/boot/dts/am335x-evmsk.dts
@@ -719,3 +719,7 @@
 &pruss_tm {
 	status = "okay";
 };
+
+&wkup_m3_ipc {
+	firmware-name = "am335x-evm-scale-data.bin";
+};
diff --git a/arch/arm/boot/dts/am335x-guardian.dts b/arch/arm/boot/dts/am335x-guardian.dts
index 1918766c1f80..f6356266564c 100644
--- a/arch/arm/boot/dts/am335x-guardian.dts
+++ b/arch/arm/boot/dts/am335x-guardian.dts
@@ -29,39 +29,42 @@
 		reg = <0x80000000 0x10000000>; /* 256 MB */
 	};
 
-	gpio_keys {
-		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
+	guardian_buttons: gpio-keys {
 		pinctrl-names = "default";
-		pinctrl-0 = <&gpio_keys_pins>;
+		pinctrl-0 = <&guardian_button_pins>;
+		compatible = "gpio-keys";
+
+		select-button {
+			label = "guardian-select-button";
+			linux,code = <KEY_5>;
+			gpios = <&gpio1 31 GPIO_ACTIVE_LOW>;
+			wakeup-source;
+		};
 
-		button21 {
+		power-button {
 			label = "guardian-power-button";
 			linux,code = <KEY_POWER>;
-			gpios = <&gpio2 21 0>;
+			gpios = <&gpio2 21 GPIO_ACTIVE_LOW>;
 			wakeup-source;
 		};
 	};
 
-	leds {
-		compatible = "gpio-leds";
+	guardian_leds: gpio-leds {
 		pinctrl-names = "default";
-		pinctrl-0 = <&leds_pins>;
+		pinctrl-0 = <&guardian_led_pins>;
+		compatible = "gpio-leds";
 
-		led1 {
-			label = "green:heartbeat";
-			gpios = <&gpio1 27 GPIO_ACTIVE_HIGH>;
+		life-led {
+			label = "guardian:life-led";
+			gpios = <&gpio1 26 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
 			default-state = "off";
 		};
+	};
 
-		led2 {
-			label = "green:mmc0";
-			gpios = <&gpio1 26 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "mmc0";
-			default-state = "off";
-		};
+	gpio-poweroff {
+		compatible = "gpio-poweroff";
+		gpios = <&gpio0 1 GPIO_ACTIVE_LOW>;
 	};
 
 	panel {
@@ -100,20 +103,36 @@
 
 	};
 
-	pwm7: dmtimer-pwm {
+	guardian_beeper: dmtimer-pwm@7 {
 		compatible = "ti,omap-dmtimer-pwm";
 		ti,timers = <&timer7>;
 		pinctrl-names = "default";
-		pinctrl-0 = <&dmtimer7_pins>;
+		pinctrl-0 = <&guardian_beeper_pins>;
 		ti,clock-source = <0x01>;
 	};
 
-	vmmcsd_fixed: regulator-3v3 {
+	vmmcsd_fixed: fixedregulator0 {
 		compatible = "regulator-fixed";
 		regulator-name = "vmmcsd_fixed";
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
 	};
+
+	mt_keypad: mt_keypad@0 {
+		compatible = "gpio-mt-keypad";
+		debounce-delay-ms = <10>;
+		col-scan-delay-us = <2>;
+		keypad,num-lines = <5>;
+		linux,no-autorepeat;
+		gpio-activelow;
+		line-gpios = <
+			&gpio1 24 GPIO_ACTIVE_LOW    /*gpio_56*/
+			&gpio1 23 GPIO_ACTIVE_LOW    /*gpio_55*/
+			&gpio1 22 GPIO_ACTIVE_LOW    /*gpio_54*/
+			&gpio1 20 GPIO_ACTIVE_LOW    /*gpio_52*/
+			&gpio1 16 GPIO_ACTIVE_LOW    /*gpio_48*/
+		>;
+	};
 };
 
 &elm {
@@ -133,28 +152,29 @@
 		interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
 			     <1 IRQ_TYPE_NONE>; /* termcount */
 		rb-gpios = <&gpmc 0 GPIO_ACTIVE_HIGH>; /* gpmc_wait0 */
+		ti,nand-xfer-type = "prefetch-dma";
 		ti,nand-ecc-opt = "bch16";
 		ti,elm-id = <&elm>;
 		nand-bus-width = <8>;
 		gpmc,device-width = <1>;
 		gpmc,sync-clk-ps = <0>;
 		gpmc,cs-on-ns = <0>;
-		gpmc,cs-rd-off-ns = <44>;
-		gpmc,cs-wr-off-ns = <44>;
-		gpmc,adv-on-ns = <6>;
-		gpmc,adv-rd-off-ns = <34>;
-		gpmc,adv-wr-off-ns = <44>;
+		gpmc,cs-rd-off-ns = <30>;
+		gpmc,cs-wr-off-ns = <30>;
+		gpmc,adv-on-ns = <0>;
+		gpmc,adv-rd-off-ns = <30>;
+		gpmc,adv-wr-off-ns = <30>;
 		gpmc,we-on-ns = <0>;
-		gpmc,we-off-ns = <40>;
-		gpmc,oe-on-ns = <0>;
-		gpmc,oe-off-ns = <54>;
-		gpmc,access-ns = <64>;
-		gpmc,rd-cycle-ns = <82>;
-		gpmc,wr-cycle-ns = <82>;
+		gpmc,we-off-ns = <15>;
+		gpmc,oe-on-ns = <1>;
+		gpmc,oe-off-ns = <15>;
+		gpmc,access-ns = <30>;
+		gpmc,rd-cycle-ns = <30>;
+		gpmc,wr-cycle-ns = <30>;
 		gpmc,bus-turnaround-ns = <0>;
 		gpmc,cycle2cycle-delay-ns = <0>;
 		gpmc,clk-activation-ns = <0>;
-		gpmc,wr-access-ns = <40>;
+		gpmc,wr-access-ns = <0>;
 		gpmc,wr-data-mux-bus-ns = <0>;
 
 		/*
@@ -198,18 +218,33 @@
 		};
 
 		partition@6 {
-			label = "u-boot-env";
-			reg = <0x300000 0x40000>;
+			label = "u-boot-2";
+			reg = <0x300000 0x100000>;
 		};
 
 		partition@7 {
-			label = "u-boot-env.backup1";
-			reg = <0x340000 0x40000>;
+			label = "u-boot-2.backup1";
+			reg = <0x400000 0x100000>;
 		};
 
 		partition@8 {
+			label = "u-boot-env";
+			reg = <0x500000 0x40000>;
+		};
+
+		partition@9 {
+			label = "u-boot-env.backup1";
+			reg = <0x540000 0x40000>;
+		};
+
+		partition@10 {
+			label = "splash-screen";
+			reg = <0x580000 0x40000>;
+		};
+
+		partition@11 {
 			label = "UBI";
-			reg = <0x380000 0x1fc80000>;
+			reg = <0x5c0000 0x1fa40000>;
 		};
 	};
 };
@@ -228,6 +263,11 @@
 &lcdc {
 	blue-and-red-wiring = "crossed";
 	status = "okay";
+	port {
+		lcdc_0: endpoint@0 {
+			remote-endpoint = <0>;
+		};
+	};
 };
 
 &mmc1 {
@@ -242,7 +282,6 @@
 &rtc {
 	clocks = <&clk_32768_ck>, <&clk_24mhz_clkctrl AM3_CLK_24MHZ_CLKDIV32K_CLKCTRL 0>;
 	clock-names = "ext-clk", "int-clk";
-	system-power-controller;
 };
 
 &spi0 {
@@ -255,14 +294,34 @@
 #include "tps65217.dtsi"
 
 &tps {
+  /*
+   * Configure pmic to enter OFF-state instead of SLEEP-state ("RTC-only
+   * mode") at poweroff.  Most BeagleBone versions do not support RTC-only
+   * mode and risk hardware damage if this mode is entered.
+   *
+   * For details, see linux-omap mailing list May 2015 thread
+   *  [PATCH] ARM: dts: am335x-bone* enable pmic-shutdown-controller
+   * In particular, messages:
+   *  http://www.spinics.net/lists/linux-omap/msg118585.html
+   *  http://www.spinics.net/lists/linux-omap/msg118615.html
+   *
+   * You can override this later with
+   *  &tps {  /delete-property/ ti,pmic-shutdown-controller;  }
+   * if you want to use RTC-only mode and made sure you are not affected
+   * by the hardware problems. (Tip: double-check by performing a current
+   * measurement after shutdown: it should be less than 1 mA.)
+   */
 	ti,pmic-shutdown-controller;
 	interrupt-parent = <&intc>;
 	interrupts = <7>; /* NMI */
 
 	backlight {
 		isel = <1>;  /* 1 - ISET1, 2 ISET2 */
-		fdim = <100>; /* TPS65217_BL_FDIM_100HZ */
-		default-brightness = <100>;
+		fdim = <500>; /* TPS65217_BL_FDIM_500HZ */
+		default-brightness = <50>;
+		/* 1(on) - enable current sink, while initialization */
+		/* 0(off) - disable current sink, while initialization */
+		isink-en = <1>;
 	};
 
 	regulators {
@@ -272,6 +331,7 @@
 		};
 
 		dcdc2_reg: regulator@1 {
+			/* VDD_MPU voltage limits 0.95V - 1.26V with +/-4% tolerance */
 			regulator-name = "vdd_mpu";
 			regulator-min-microvolt = <925000>;
 			regulator-max-microvolt = <1351500>;
@@ -280,6 +340,7 @@
 		};
 
 		dcdc3_reg: regulator@2 {
+			/* VDD_CORE voltage limits 0.95V - 1.1V with +/-4% tolerance */
 			regulator-name = "vdd_core";
 			regulator-min-microvolt = <925000>;
 			regulator-max-microvolt = <1150000>;
@@ -319,171 +380,364 @@
 	};
 };
 
+&gpio0 {
+	gpio-line-names =
+		"",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"MirxWakeup",
+		"",
+		"";
+};
+
+&gpio3 {
+	ti,gpio-always-on;
+	ti,no-reset-on-init;
+	gpio-line-names =
+		"",
+		"MirxBtReset",
+		"",
+		"CcVolAdcEn",
+		"MirxBlePause",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"AspEn",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"BatVolAdcEn",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"",
+		"";
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_pins>;
 	status = "okay";
 };
 
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart2_pins>;
+	status = "okay";
+};
+
 &usb0 {
 	dr_mode = "peripheral";
 };
 
 &usb1 {
 	dr_mode = "host";
+	/delete-property/dmas;
+	/delete-property/dma-names;
 };
 
 &am33xx_pinmux {
 	pinctrl-names = "default";
-	pinctrl-0 = <&clkout2_pin &gpio_pins>;
+	pinctrl-0 = <&clkout2_pin &guardian_interface_pins>;
 
 	clkout2_pin: pinmux_clkout2_pin {
 		pinctrl-single,pins = <
+			/* xdma_event_intr1.clkout2 */
 			AM33XX_IOPAD(0x9b4, PIN_OUTPUT_PULLDOWN | MUX_MODE3)
 		>;
 	};
 
-	dmtimer7_pins: pinmux_dmtimer7_pins {
+	guardian_interface_pins: pinmux_interface_pins {
 		pinctrl-single,pins = <
-			AM33XX_IOPAD(0x968, PIN_OUTPUT | MUX_MODE5)
+			/* ADC_BATSENSE_EN */
+			/* (A14) MCASP0_AHCLKx.gpio3[21] */
+			AM33XX_IOPAD(0x9ac, PIN_OUTPUT_PULLDOWN | MUX_MODE7 )
+			/* ADC_COINCELL_EN */
+			/* (J16) MII1_TX_EN.gpio3[3] */
+			AM33XX_IOPAD(0x914, PIN_OUTPUT_PULLDOWN | MUX_MODE7 )
+			/* ASP_ENABLE */
+			/* (A13) MCASP0_ACLKx.gpio3[14] */
+			AM33XX_IOPAD(0x990, PIN_OUTPUT_PULLUP | MUX_MODE7)
+			/* (D16) uart1_rxd.uart1_rxd */
+			AM33XX_IOPAD(0x980, PIN_INPUT | MUX_MODE7)
+			/* (D15) uart1_txd.uart1_txd */
+			AM33XX_IOPAD(0x984, PIN_INPUT | MUX_MODE7)
+			/*SWITCH-OFF_3V6*/
+			/* (M18) gpio0[1] */
+			AM33XX_IOPAD(0x94c, PIN_OUTPUT_PULLUP | MUX_MODE7)
+			/* MIRACULIX */
+			/* (H17) gmii1_crs.gpio3[1] */
+			AM33XX_IOPAD(0x90c, PIN_OUTPUT_PULLDOWN | MUX_MODE7 )
+			/* (H18) rmii1_refclk.gpio0[29] */
+			AM33XX_IOPAD(0x944, PIN_OUTPUT_PULLDOWN | MUX_MODE7 )
+			/* (J18) gmii1_txd3.gpio0[16] */
+			AM33XX_IOPAD(0x91c, PIN_INPUT           | MUX_MODE7 )
+			/* (J17) gmii1_rxdv.gpio3[4] */
+			AM33XX_IOPAD(0x918, PIN_OUTPUT_PULLDOWN | MUX_MODE7 )
 		>;
 	};
 
-	gpio_keys_pins: pinmux_gpio_keys_pins {
+	guardian_beeper_pins: pinmux_dmtimer7_pins {
 		pinctrl-single,pins = <
-			AM33XX_IOPAD(0x940, PIN_INPUT | MUX_MODE7)
+			AM33XX_IOPAD(0x968, PIN_OUTPUT | MUX_MODE5) /* (E18) timer7 */
 		>;
 	};
 
-	gpio_pins: pinmux_gpio_pins {
+	guardian_button_pins: pinmux_guardian_button_pins {
 		pinctrl-single,pins = <
-			AM33XX_IOPAD(0x928, PIN_OUTPUT | MUX_MODE7)
-			AM33XX_IOPAD(0x990, PIN_OUTPUT | MUX_MODE7)
+			AM33XX_IOPAD(0x940, PIN_INPUT | MUX_MODE7) /* (M16) gmii1_rxd0.gpio2[21] */
+			AM33XX_IOPAD(0x884, PIN_INPUT | MUX_MODE7) /* (V9)  gpmc_csn2.gpio1[31] */
 		>;
 	};
 
+
 	i2c0_pins: pinmux_i2c0_pins {
 		pinctrl-single,pins = <
-			AM33XX_IOPAD(0x988, PIN_INPUT_PULLUP | MUX_MODE0)
-			AM33XX_IOPAD(0x98c, PIN_INPUT_PULLUP | MUX_MODE0)
+			AM33XX_IOPAD(0x988, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_sda.i2c0_sda */
+			AM33XX_IOPAD(0x98c, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c0_scl.i2c0_scl */
+		>;
+	};
+
+	led_bl_pins: gpio_led_bl_pins {
+		pinctrl-single,pins = <
+			/* P9_14, gpmc_a[2].GPIO1[18] (backlight control) */
+			AM33XX_IOPAD(0x848, PIN_OUTPUT | MUX_MODE7)
 		>;
 	};
 
 	lcd_disen_pins: pinmux_lcd_disen_pins {
 		pinctrl-single,pins = <
+			/* P9_27, mcasp0_fsr.gpio3[19] (lcd_disen) */
 			AM33XX_IOPAD(0x9a4, PIN_OUTPUT_PULLUP | SLEWCTRL_SLOW | MUX_MODE7)
 		>;
 	};
 
 	lcd_pins_default: pinmux_lcd_pins_default {
 		pinctrl-single,pins = <
+			/* (U10) gpmc_ad8.lcd_data23 */
 			AM33XX_IOPAD(0x820, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE1)
+			/* (T10) gpmc_ad9.lcd_data22 */
 			AM33XX_IOPAD(0x824, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE1)
+			/* (T11) gpmc_ad10.lcd_data21 */
 			AM33XX_IOPAD(0x828, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE1)
+			/* (U12) gpmc_ad11.lcd_data20 */
 			AM33XX_IOPAD(0x82c, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE1)
+			/* (T12) gpmc_ad12.lcd_data19 */
 			AM33XX_IOPAD(0x830, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE1)
+			/* (R12) gpmc_ad13.lcd_data18 */
 			AM33XX_IOPAD(0x834, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE1)
+			/* (V13) gpmc_ad14.lcd_data17 */
 			AM33XX_IOPAD(0x838, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE1)
+			/* (U13) gpmc_ad15.lcd_data16 */
 			AM33XX_IOPAD(0x83c, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE1)
+			/* lcd_data0.lcd_data0 */
 			AM33XX_IOPAD(0x8a0, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE0)
+			/* lcd_data1.lcd_data1 */
 			AM33XX_IOPAD(0x8a4, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE0)
+			/* lcd_data2.lcd_data2 */
 			AM33XX_IOPAD(0x8a8, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE0)
+			/* lcd_data3.lcd_data3 */
 			AM33XX_IOPAD(0x8ac, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE0)
+			/* lcd_data4.lcd_data4 */
 			AM33XX_IOPAD(0x8b0, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE0)
+			/* lcd_data5.lcd_data5 */
 			AM33XX_IOPAD(0x8b4, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE0)
+			/* lcd_data6.lcd_data6 */
 			AM33XX_IOPAD(0x8b8, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE0)
+			/* lcd_data7.lcd_data7 */
 			AM33XX_IOPAD(0x8bc, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE0)
+			/* lcd_data8.lcd_data8 */
 			AM33XX_IOPAD(0x8c0, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE0)
+			/* lcd_data9.lcd_data9 */
 			AM33XX_IOPAD(0x8c4, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE0)
+			/* lcd_data10.lcd_data10 */
 			AM33XX_IOPAD(0x8c8, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE0)
+			/* lcd_data11.lcd_data11 */
 			AM33XX_IOPAD(0x8cc, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE0)
+			/* lcd_data12.lcd_data12 */
 			AM33XX_IOPAD(0x8d0, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE0)
+			/* lcd_data13.lcd_data13 */
 			AM33XX_IOPAD(0x8d4, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE0)
+			/* lcd_data14.lcd_data14 */
 			AM33XX_IOPAD(0x8d8, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE0)
+			/* lcd_data15.lcd_data15 */
 			AM33XX_IOPAD(0x8dc, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE0)
+			/* lcd_vsync.lcd_vsync */
 			AM33XX_IOPAD(0x8e0, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE0)
+			/* lcd_hsync.lcd_hsync */
 			AM33XX_IOPAD(0x8e4, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE0)
+			/* lcd_pclk.lcd_pclk */
 			AM33XX_IOPAD(0x8e8, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE0)
+			/* lcd_ac_bias_en.lcd_ac_bias_en */
 			AM33XX_IOPAD(0x8ec, PIN_OUTPUT | SLEWCTRL_SLOW | MUX_MODE0)
 		>;
 	};
 
 	lcd_pins_sleep: pinmux_lcd_pins_sleep {
 		pinctrl-single,pins = <
+			/* lcd_data0.lcd_data0 */
 			AM33XX_IOPAD(0x8a0, PULL_DISABLE | SLEWCTRL_SLOW | MUX_MODE7)
+			/* lcd_data1.lcd_data1 */
 			AM33XX_IOPAD(0x8a4, PULL_DISABLE | SLEWCTRL_SLOW | MUX_MODE7)
+			/* lcd_data2.lcd_data2 */
 			AM33XX_IOPAD(0x8a8, PULL_DISABLE | SLEWCTRL_SLOW | MUX_MODE7)
+			/* lcd_data3.lcd_data3 */
 			AM33XX_IOPAD(0x8ac, PULL_DISABLE | SLEWCTRL_SLOW | MUX_MODE7)
+			/* lcd_data4.lcd_data4 */
 			AM33XX_IOPAD(0x8b0, PULL_DISABLE | SLEWCTRL_SLOW | MUX_MODE7)
+			/* lcd_data5.lcd_data5 */
 			AM33XX_IOPAD(0x8b4, PULL_DISABLE | SLEWCTRL_SLOW | MUX_MODE7)
+			/* lcd_data6.lcd_data6 */
 			AM33XX_IOPAD(0x8b8, PULL_DISABLE | SLEWCTRL_SLOW | MUX_MODE7)
+			/* lcd_data7.lcd_data7 */
 			AM33XX_IOPAD(0x8bc, PULL_DISABLE | SLEWCTRL_SLOW | MUX_MODE7)
+			/* lcd_data8.lcd_data8 */
 			AM33XX_IOPAD(0x8c0, PULL_DISABLE | SLEWCTRL_SLOW | MUX_MODE7)
+			/* lcd_data9.lcd_data9 */
 			AM33XX_IOPAD(0x8c4, PULL_DISABLE | SLEWCTRL_SLOW | MUX_MODE7)
+			/* lcd_data10.lcd_data10 */
 			AM33XX_IOPAD(0x8c8, PULL_DISABLE | SLEWCTRL_SLOW | MUX_MODE7)
+			/* lcd_data11.lcd_data11 */
 			AM33XX_IOPAD(0x8cc, PULL_DISABLE | SLEWCTRL_SLOW | MUX_MODE7)
+			/* lcd_data12.lcd_data12 */
 			AM33XX_IOPAD(0x8d0, PULL_DISABLE | SLEWCTRL_SLOW | MUX_MODE7)
+			/* lcd_data13.lcd_data13 */
 			AM33XX_IOPAD(0x8d4, PULL_DISABLE | SLEWCTRL_SLOW | MUX_MODE7)
+			/* lcd_data14.lcd_data14 */
 			AM33XX_IOPAD(0x8d8, PULL_DISABLE | SLEWCTRL_SLOW | MUX_MODE7)
+			/* lcd_data15.lcd_data15 */
 			AM33XX_IOPAD(0x8dc, PULL_DISABLE | SLEWCTRL_SLOW | MUX_MODE7)
+			/* lcd_vsync.lcd_vsync */
 			AM33XX_IOPAD(0x8e0, PIN_INPUT_PULLDOWN | SLEWCTRL_SLOW | MUX_MODE7)
+			/* lcd_hsync.lcd_hsync */
 			AM33XX_IOPAD(0x8e4, PIN_INPUT_PULLDOWN | SLEWCTRL_SLOW | MUX_MODE7)
+			/* lcd_pclk.lcd_pclk */
 			AM33XX_IOPAD(0x8e8, PIN_INPUT_PULLDOWN | SLEWCTRL_SLOW | MUX_MODE7)
+			/* lcd_ac_bias_en.lcd_ac_bias_en */
 			AM33XX_IOPAD(0x8ec, PIN_INPUT_PULLDOWN | SLEWCTRL_SLOW | MUX_MODE7)
 		>;
 	};
 
-	leds_pins: pinmux_leds_pins {
+	guardian_led_pins: pinmux_guardian_led_pins {
 		pinctrl-single,pins = <
-			AM33XX_IOPAD(0x868, PIN_OUTPUT | MUX_MODE7)
-			AM33XX_IOPAD(0x86c, PIN_OUTPUT | MUX_MODE7)
+			AM33XX_IOPAD(0x868, PIN_OUTPUT | MUX_MODE7) /* (T16) gpmc_a10.gpio1[26] */
 		>;
 	};
 
 	mmc1_pins: pinmux_mmc1_pins {
 		pinctrl-single,pins = <
-			AM33XX_IOPAD(0x8f0, PIN_INPUT_PULLUP | MUX_MODE0)
-			AM33XX_IOPAD(0x8f4, PIN_INPUT_PULLUP | MUX_MODE0)
-			AM33XX_IOPAD(0x8f8, PIN_INPUT_PULLUP | MUX_MODE0)
-			AM33XX_IOPAD(0x8fc, PIN_INPUT_PULLUP | MUX_MODE0)
-			AM33XX_IOPAD(0x900, PIN_INPUT_PULLUP | MUX_MODE0)
-			AM33XX_IOPAD(0x904, PIN_INPUT_PULLUP | MUX_MODE0)
-			AM33XX_IOPAD(0x960, PIN_INPUT | MUX_MODE7)
+			AM33XX_IOPAD(0x8f0, PIN_INPUT_PULLUP | MUX_MODE0)  /* mmc0_dat3.mmc0_dat3 */
+			AM33XX_IOPAD(0x8f4, PIN_INPUT_PULLUP | MUX_MODE0)  /* mmc0_dat2.mmc0_dat2 */
+			AM33XX_IOPAD(0x8f8, PIN_INPUT_PULLUP | MUX_MODE0)  /* mmc0_dat1.mmc0_dat1 */
+			AM33XX_IOPAD(0x8fc, PIN_INPUT_PULLUP | MUX_MODE0)  /* mmc0_dat0.mmc0_dat0 */
+			AM33XX_IOPAD(0x900, PIN_INPUT_PULLUP | MUX_MODE0)  /* mmc0_clk.mmc0_clk */
+			AM33XX_IOPAD(0x904, PIN_INPUT_PULLUP | MUX_MODE0)  /* mmc0_cmd.mmc0_cmd */
+			AM33XX_IOPAD(0x960, PIN_INPUT | MUX_MODE7)         /* GPIO0_6 */
 		>;
 	};
 
 	spi0_pins: pinmux_spi0_pins {
 		pinctrl-single,pins = <
+			/* SPI0_CLK  - spi0_clk.spi */
 			AM33XX_IOPAD(0x950, PIN_OUTPUT_PULLDOWN | MUX_MODE0)
+			/* SPI0_MOSI - spi0_d0.spi0 */
 			AM33XX_IOPAD(0x954, PIN_OUTPUT_PULLUP | MUX_MODE0)
+			/* SPI0_MISO - spi0_d1.spi0 */
 			AM33XX_IOPAD(0x958, PIN_INPUT_PULLUP | MUX_MODE0)
+			/* SPI0_CS0 - spi */
 			AM33XX_IOPAD(0x95c, PIN_OUTPUT_PULLUP | MUX_MODE0)
 		>;
 	};
 
 	uart0_pins: pinmux_uart0_pins {
 		pinctrl-single,pins = <
+			/* uart0_rxd.uart0_rxd */
 			AM33XX_IOPAD(0x970, PIN_INPUT_PULLUP | MUX_MODE0)
+			/* uart0_txd.uart0_txd */
 			AM33XX_IOPAD(0x974, PIN_OUTPUT_PULLDOWN | MUX_MODE0)
 		>;
 	};
 
+	uart2_pins: pinmux_uart2_pins {
+		pinctrl-single,pins = <
+			/* K18 uart2_rxd.mirx_txd */
+			AM33XX_IOPAD(0x92c, PIN_INPUT_PULLUP | MUX_MODE1)
+			/* L18 uart2_txd.mirx_rxd */
+			AM33XX_IOPAD(0x930, PIN_OUTPUT_PULLDOWN | MUX_MODE1)
+		>;
+	};
+
 	nandflash_pins: pinmux_nandflash_pins {
 		pinctrl-single,pins = <
+			/* (U7) gpmc_ad0.gpmc_ad0 */
 			AM33XX_IOPAD(0x800, PIN_INPUT | MUX_MODE0)
+			/* (V7) gpmc_ad1.gpmc_ad1 */
 			AM33XX_IOPAD(0x804, PIN_INPUT | MUX_MODE0)
+			/* (R8) gpmc_ad2.gpmc_ad2 */
 			AM33XX_IOPAD(0x808, PIN_INPUT | MUX_MODE0)
+			/* (T8) gpmc_ad3.gpmc_ad3 */
 			AM33XX_IOPAD(0x80c, PIN_INPUT | MUX_MODE0)
+			/* (U8) gpmc_ad4.gpmc_ad4 */
 			AM33XX_IOPAD(0x810, PIN_INPUT | MUX_MODE0)
+			/* (V8) gpmc_ad5.gpmc_ad5 */
 			AM33XX_IOPAD(0x814, PIN_INPUT | MUX_MODE0)
+			/* (R9) gpmc_ad6.gpmc_ad6 */
 			AM33XX_IOPAD(0x818, PIN_INPUT | MUX_MODE0)
+			/* (T9) gpmc_ad7.gpmc_ad7 */
 			AM33XX_IOPAD(0x81c, PIN_INPUT | MUX_MODE0)
+			/* (T17) gpmc_wait0.gpmc_wait0 */
 			AM33XX_IOPAD(0x870, PIN_INPUT | MUX_MODE0)
+			/* (U17) gpmc_wpn.gpmc_wpn */
 			AM33XX_IOPAD(0x874, PIN_OUTPUT | MUX_MODE0)
+			/* (V6) gpmc_csn0.gpmc_csn0 */
 			AM33XX_IOPAD(0x87c, PIN_OUTPUT | MUX_MODE0)
+			/* (R7) gpmc_advn_ale.gpmc_advn_ale */
 			AM33XX_IOPAD(0x890, PIN_OUTPUT | MUX_MODE0)
+			/* (T7) gpmc_oen_ren.gpmc_oen_ren */
 			AM33XX_IOPAD(0x894, PIN_OUTPUT | MUX_MODE0)
+			/* (U6) gpmc_wen.gpmc_wen */
 			AM33XX_IOPAD(0x898, PIN_OUTPUT | MUX_MODE0)
+			/* (T6) gpmc_be0n_cle.gpmc_be0n_cle */
 			AM33XX_IOPAD(0x89c, PIN_OUTPUT | MUX_MODE0)
 		>;
 	};
diff --git a/arch/arm/boot/dts/am335x-icev2.dts b/arch/arm/boot/dts/am335x-icev2.dts
index e5ce89c8f54d..5835c0cdda50 100644
--- a/arch/arm/boot/dts/am335x-icev2.dts
+++ b/arch/arm/boot/dts/am335x-icev2.dts
@@ -512,3 +512,7 @@
 &pruss_tm {
 	status = "okay";
 };
+
+&rtc {
+	system-power-controller;
+};
diff --git a/arch/arm/boot/dts/am335x-moxa-uc-2100-common.dtsi b/arch/arm/boot/dts/am335x-moxa-uc-2100-common.dtsi
index 11e8f64b6606..7b40ca9483ca 100644
--- a/arch/arm/boot/dts/am335x-moxa-uc-2100-common.dtsi
+++ b/arch/arm/boot/dts/am335x-moxa-uc-2100-common.dtsi
@@ -166,10 +166,8 @@
 &buttons {
 	pinctrl-names = "default";
 	pinctrl-0 = <&push_button_pins>;
-	#address-cells = <1>;
-	#size-cells = <0>;
 
-	button@0 {
+	button-0 {
 		label = "push_button";
 		linux,code = <0x100>;
 		gpios = <&gpio2 23 GPIO_ACTIVE_LOW>;
@@ -182,7 +180,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&spi0_pins>;
 
-	m25p80@0 {
+	flash@0 {
 		compatible = "mx25l6405d";
 		spi-max-frequency = <40000000>;
 
diff --git a/arch/arm/boot/dts/am335x-moxa-uc-8100-common.dtsi b/arch/arm/boot/dts/am335x-moxa-uc-8100-common.dtsi
index a7269b90d795..e0364adb8393 100644
--- a/arch/arm/boot/dts/am335x-moxa-uc-8100-common.dtsi
+++ b/arch/arm/boot/dts/am335x-moxa-uc-8100-common.dtsi
@@ -378,10 +378,8 @@
 &buttons {
 	pinctrl-names = "default";
 	pinctrl-0 = <&push_button_pins>;
-	#address-cells = <1>;
-	#size-cells = <0>;
 
-	button@0 {
+	button-0 {
 		label = "push_button";
 		linux,code = <0x100>;
 		gpios = <&gpio3 21 GPIO_ACTIVE_LOW>;
@@ -394,7 +392,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&spi0_pins>;
 
-	m25p80@0 {
+	flash@0 {
 		compatible = "mx25l6405d";
 		spi-max-frequency = <40000000>;
 
diff --git a/arch/arm/boot/dts/am335x-myirtech-myc.dtsi b/arch/arm/boot/dts/am335x-myirtech-myc.dtsi
index 245c35f41cdf..6eea18b29355 100644
--- a/arch/arm/boot/dts/am335x-myirtech-myc.dtsi
+++ b/arch/arm/boot/dts/am335x-myirtech-myc.dtsi
@@ -27,6 +27,13 @@
 		reg = <0x80000000 0x10000000>;
 	};
 
+	clk32k: clk32k {
+		compatible = "fixed-clock";
+		clock-frequency = <32768>;
+
+		#clock-cells = <0>;
+	};
+
 	vdd_mod: vdd_mod_reg {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd-mod";
@@ -124,9 +131,6 @@
 		gpmc,wr-data-mux-bus-ns = <0>;
 		ti,elm-id = <&elm>;
 		ti,nand-ecc-opt = "bch8";
-
-		#address-cells = <1>;
-		#size-cells = <1>;
 	};
 };
 
@@ -149,6 +153,8 @@
 };
 
 &rtc {
+	clocks = <&clk32k>;
+	clock-names = "ext-clk";
 	system-power-controller;
 };
 
diff --git a/arch/arm/boot/dts/am335x-myirtech-myd.dts b/arch/arm/boot/dts/am335x-myirtech-myd.dts
index 1479fd95dec2..9d81d4cc6890 100644
--- a/arch/arm/boot/dts/am335x-myirtech-myd.dts
+++ b/arch/arm/boot/dts/am335x-myirtech-myd.dts
@@ -227,14 +227,20 @@
 };
 
 &nand0 {
-	partition@0 {
-		label = "MLO";
-		reg = <0x00000 0x20000>;
-	};
+	nand_parts: partitions {
+		compatible = "fixed-partitions";
+		#address-cells = <1>;
+		#size-cells = <1>;
 
-	partition@20000 {
-		label = "boot";
-		reg = <0x20000 0x80000>;
+		partition@0 {
+			label = "MLO";
+			reg = <0x00000 0x20000>;
+		};
+
+		partition@80000 {
+			label = "boot";
+			reg = <0x80000 0x100000>;
+		};
 	};
 };
 
diff --git a/arch/arm/boot/dts/am335x-netcan-plus-1xx.dts b/arch/arm/boot/dts/am335x-netcan-plus-1xx.dts
index 57e756b0f192..2e049489ac06 100644
--- a/arch/arm/boot/dts/am335x-netcan-plus-1xx.dts
+++ b/arch/arm/boot/dts/am335x-netcan-plus-1xx.dts
@@ -85,3 +85,147 @@
 
 	status = "okay";
 };
+
+&gpio0 {
+	gpio-line-names =
+		"MDIO",
+		"MDC",
+		"NC",
+		"NC",
+		"I2C1_SDA",
+		"I2C1_SCL",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"can_data",
+		"can_error",
+		"onrisc:blue:wlan",
+		"onrisc:green:app",
+		"USB0_DRVVBUS",
+		"ETH2_INT",
+		"NC",
+		"NC",
+		"MMC1_DAT0",
+		"MMC1_DAT1",
+		"NC",
+		"NC",
+		"MMC1_DAT2",
+		"MMC1_DAT3",
+		"NC",
+		"NC",
+		"GPMC_WAIT0",
+		"GPMC_WP_N";
+};
+
+&gpio1 {
+	gpio-line-names =
+		"GPMC_AD0",
+		"GPMC_AD1",
+		"GPMC_AD2",
+		"GPMC_AD3",
+		"GPMC_AD4",
+		"GPMC_AD5",
+		"GPMC_AD6",
+		"GPMC_AD7",
+		"DCAN1_TX",
+		"DCAN1_RX",
+		"CONSOLE_RX",
+		"CONSOLE_TX",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"RGMII2_TCTL",
+		"RGMII2_RCTL",
+		"RGMII2_TD3",
+		"RGMII2_TD2",
+		"RGMII2_TD1",
+		"RGMII2_TD0",
+		"RGMII2_TCLK",
+		"RGMII2_RCLK",
+		"RGMII2_RD3",
+		"RGMII2_RD2",
+		"RGMII2_RD1",
+		"RGMII2_RD0",
+		"PMIC_INT1",
+		"GPMC_CSN0_Flash",
+		"MMC1_CLK",
+		"MMC1_CMD";
+};
+
+&gpio2 {
+	gpio-line-names =
+		"GPMC_CSN3_BUS",
+		"GPMC_CLK",
+		"GPMC_ADVN_ALE",
+		"GPMC_OEN_RE_N",
+		"GPMC_WE_N",
+		"GPMC_BEN0_CLE",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"SW2_0",
+		"SW2_1",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"MMC0_DAT3",
+		"MMC0_DAT2",
+		"MMC0_DAT1",
+		"MMC0_DAT0",
+		"MMC0_CLK",
+		"MMC0_CMD";
+};
+
+&gpio3 {
+	gpio-line-names =
+		"onrisc:red:power",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"WLAN_IRQ",
+		"WLAN_EN",
+		"SW2_2",
+		"SW2_3",
+		"NC",
+		"NC",
+		"NC",
+		"ModeA0",
+		"ModeA1",
+		"ModeA2",
+		"ModeA3",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC";
+};
diff --git a/arch/arm/boot/dts/am335x-netcom-plus-2xx.dts b/arch/arm/boot/dts/am335x-netcom-plus-2xx.dts
index c6cc1c6218a9..6ed886c3306b 100644
--- a/arch/arm/boot/dts/am335x-netcom-plus-2xx.dts
+++ b/arch/arm/boot/dts/am335x-netcom-plus-2xx.dts
@@ -93,3 +93,147 @@
 	ti,dual-emac-pvid = <2>;
 	phy-handle = <&phy1>;
 };
+
+&gpio0 {
+	gpio-line-names =
+		"MDIO",
+		"MDC",
+		"UART2_RX",
+		"UART2_TX",
+		"I2C1_SDA",
+		"I2C1_SCL",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"UART1_CTSN",
+		"UART1_RTSN",
+		"UART1_RX",
+		"UART1_TX",
+		"onrisc:blue:wlan",
+		"onrisc:green:app",
+		"USB0_DRVVBUS",
+		"ETH2_INT",
+		"NC",
+		"NC",
+		"MMC1_DAT0",
+		"MMC1_DAT1",
+		"NC",
+		"NC",
+		"MMC1_DAT2",
+		"MMC1_DAT3",
+		"NC",
+		"NC",
+		"GPMC_WAIT0",
+		"GPMC_WP_N";
+};
+
+&gpio1 {
+	gpio-line-names =
+		"GPMC_AD0",
+		"GPMC_AD1",
+		"GPMC_AD2",
+		"GPMC_AD3",
+		"GPMC_AD4",
+		"GPMC_AD5",
+		"GPMC_AD6",
+		"GPMC_AD7",
+		"NC",
+		"NC",
+		"CONSOLE_RX",
+		"CONSOLE_TX",
+		"UART2_DTR",
+		"UART2_DSR",
+		"UART2_DCD",
+		"UART2_RI",
+		"RGMII2_TCTL",
+		"RGMII2_RCTL",
+		"RGMII2_TD3",
+		"RGMII2_TD2",
+		"RGMII2_TD1",
+		"RGMII2_TD0",
+		"RGMII2_TCLK",
+		"RGMII2_RCLK",
+		"RGMII2_RD3",
+		"RGMII2_RD2",
+		"RGMII2_RD1",
+		"RGMII2_RD0",
+		"PMIC_INT1",
+		"GPMC_CSN0_Flash",
+		"MMC1_CLK",
+		"MMC1_CMD";
+};
+
+&gpio2 {
+	gpio-line-names =
+		"GPMC_CSN3_BUS",
+		"GPMC_CLK",
+		"GPMC_ADVN_ALE",
+		"GPMC_OEN_RE_N",
+		"GPMC_WE_N",
+		"GPMC_BEN0_CLE",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"SW2_0",
+		"SW2_1",
+		"NC",
+		"NC",
+		"UART1_DTR",
+		"UART1_DSR",
+		"UART1_DCD",
+		"UART1_RI",
+		"MMC0_DAT3",
+		"MMC0_DAT2",
+		"MMC0_DAT1",
+		"MMC0_DAT0",
+		"MMC0_CLK",
+		"MMC0_CMD";
+};
+
+&gpio3 {
+	gpio-line-names =
+		"onrisc:red:power",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"UART2_CTSN",
+		"UART2_RTSN",
+		"WLAN_IRQ",
+		"WLAN_EN",
+		"SW2_2",
+		"SW2_3",
+		"NC",
+		"NC",
+		"NC",
+		"ModeA0",
+		"ModeA1",
+		"ModeA2",
+		"ModeA3",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC";
+};
diff --git a/arch/arm/boot/dts/am335x-netcom-plus-8xx.dts b/arch/arm/boot/dts/am335x-netcom-plus-8xx.dts
index 96dffd3ffd85..ad3adc7679f9 100644
--- a/arch/arm/boot/dts/am335x-netcom-plus-8xx.dts
+++ b/arch/arm/boot/dts/am335x-netcom-plus-8xx.dts
@@ -71,6 +71,10 @@
 		interrupts = <20 IRQ_TYPE_EDGE_RISING>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&tca6416_pins>;
+		gpio-line-names = "GP_IN0", "GP_IN1", "GP_IN2", "GP_IN3",
+				  "GP_IN4", "GP_IN5", "GP_IN6", "GP_IN7",
+				  "GP_OUT0", "GP_OUT1", "GP_OUT2", "GP_OUT3",
+				  "GP_OUT4", "GP_OUT5", "GP_OUT6", "GP_OUT7";
 	};
 };
 
@@ -86,6 +90,10 @@
 		reg = <0x20>;
 		gpio-controller;
 		#gpio-cells = <2>;
+		gpio-line-names = "CH1_M0", "CH1_M1", "CH1_M2", "CH1_M3",
+				  "CH2_M0", "CH2_M1", "CH2_M2", "CH2_M3",
+				  "CH3_M0", "CH3_M1", "CH3_M2", "CH3_M3",
+				  "CH4_M0", "CH4_M1", "CH4_M2", "CH4_M3";
 	};
 
 	tca6416c: gpio@21 {
@@ -93,6 +101,10 @@
 		reg = <0x21>;
 		gpio-controller;
 		#gpio-cells = <2>;
+		gpio-line-names = "CH5_M0", "CH5_M1", "CH5_M2", "CH5_M3",
+				  "CH6_M0", "CH6_M1", "CH6_M2", "CH6_M3",
+				  "CH7_M0", "CH7_M1", "CH7_M2", "CH7_M3",
+				  "CH8_M0", "CH8_M1", "CH8_M2", "CH8_M3";
 	};
 };
 
@@ -113,3 +125,147 @@
 	ti,dual-emac-pvid = <2>;
 	phy-handle = <&phy1>;
 };
+
+&gpio0 {
+	gpio-line-names =
+		"MDIO",
+		"MDC",
+		"NC",
+		"NC",
+		"I2C1_SDA",
+		"I2C1_SCL",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"I2C2_SDA",
+		"I2C2_SCL",
+		"NC",
+		"NC",
+		"onrisc:blue:wlan",
+		"onrisc:green:app",
+		"USB0_DRVVBUS",
+		"ETH2_INT",
+		"NC",
+		"NC",
+		"MMC1_DAT0",
+		"MMC1_DAT1",
+		"NC",
+		"NC",
+		"MMC1_DAT2",
+		"MMC1_DAT3",
+		"NC",
+		"NC",
+		"GPMC_WAIT0",
+		"GPMC_WP_N";
+};
+
+&gpio1 {
+	gpio-line-names =
+		"GPMC_AD0",
+		"GPMC_AD1",
+		"GPMC_AD2",
+		"GPMC_AD3",
+		"GPMC_AD4",
+		"GPMC_AD5",
+		"GPMC_AD6",
+		"GPMC_AD7",
+		"NC",
+		"NC",
+		"CONSOLE_RX",
+		"CONSOLE_TX",
+		"SW2_0_alt",
+		"SW2_1_alt",
+		"SW2_2_alt",
+		"SW2_3_alt",
+		"RGMII2_TCTL",
+		"RGMII2_RCTL",
+		"RGMII2_TD3",
+		"RGMII2_TD2",
+		"RGMII2_TD1",
+		"RGMII2_TD0",
+		"RGMII2_TCLK",
+		"RGMII2_RCLK",
+		"RGMII2_RD3",
+		"RGMII2_RD2",
+		"RGMII2_RD1",
+		"RGMII2_RD0",
+		"PMIC_INT1",
+		"GPMC_CSN0_Flash",
+		"MMC1_CLK",
+		"MMC1_CMD";
+};
+
+&gpio2 {
+	gpio-line-names =
+		"GPMC_CSN3_BUS",
+		"GPMC_CLK",
+		"GPMC_ADVN_ALE",
+		"GPMC_OEN_RE_N",
+		"GPMC_WE_N",
+		"GPMC_BEN0_CLE",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"SW2_0",
+		"SW2_1",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"MMC0_DAT3",
+		"MMC0_DAT2",
+		"MMC0_DAT1",
+		"MMC0_DAT0",
+		"MMC0_CLK",
+		"MMC0_CMD";
+};
+
+&gpio3 {
+	gpio-line-names =
+		"onrisc:red:power",
+		"NC",
+		"NC",
+		"NC",
+		"3G_PWR_EN",
+		"NC",
+		"NC",
+		"WLAN_IRQ",
+		"WLAN_EN",
+		"SW2_2",
+		"SW2_3",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC",
+		"NC";
+};
diff --git a/arch/arm/boot/dts/am335x-osd3358-sm-red.dts b/arch/arm/boot/dts/am335x-osd3358-sm-red.dts
index 605b2a436edf..b2846cd220f0 100644
--- a/arch/arm/boot/dts/am335x-osd3358-sm-red.dts
+++ b/arch/arm/boot/dts/am335x-osd3358-sm-red.dts
@@ -84,7 +84,7 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 			ax8975@c {
-				compatible = "ak,ak8975";
+				compatible = "asahi-kasei,ak8975";
 				reg = <0x0c>;
 			};
 		};
diff --git a/arch/arm/boot/dts/am335x-pcm-953.dtsi b/arch/arm/boot/dts/am335x-pcm-953.dtsi
index 124026fa0d09..dae448040a97 100644
--- a/arch/arm/boot/dts/am335x-pcm-953.dtsi
+++ b/arch/arm/boot/dts/am335x-pcm-953.dtsi
@@ -54,14 +54,14 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&user_buttons_pins>;
 
-		button@0 {
+		button-0 {
 			label = "home";
 			linux,code = <KEY_HOME>;
 			gpios = <&gpio3 7 GPIO_ACTIVE_HIGH>;
 			wakeup-source;
 		};
 
-		button@1 {
+		button-1 {
 			label = "menu";
 			linux,code = <KEY_MENU>;
 			gpios = <&gpio3 8 GPIO_ACTIVE_HIGH>;
diff --git a/arch/arm/boot/dts/am335x-pdu001.dts b/arch/arm/boot/dts/am335x-pdu001.dts
index b793beeab245..ce6cc2b96654 100644
--- a/arch/arm/boot/dts/am335x-pdu001.dts
+++ b/arch/arm/boot/dts/am335x-pdu001.dts
@@ -353,7 +353,7 @@
 		};
 	};
 
-	mcp79400: mcp79400@6f {
+	mcp79400: rtc@6f {
 		compatible = "microchip,mcp7940x";
 		reg = <0x6f>;
 	};
diff --git a/arch/arm/boot/dts/am335x-pepper.dts b/arch/arm/boot/dts/am335x-pepper.dts
index b5e88e627bc1..8691eec33b61 100644
--- a/arch/arm/boot/dts/am335x-pepper.dts
+++ b/arch/arm/boot/dts/am335x-pepper.dts
@@ -596,24 +596,22 @@
 &buttons {
 	pinctrl-names = "default";
 	pinctrl-0 = <&user_buttons_pins>;
-	#address-cells = <1>;
-	#size-cells = <0>;
 
-	button0 {
+	button-0 {
 		label = "home";
 		linux,code = <KEY_HOME>;
 		gpios = <&gpio1 22 GPIO_ACTIVE_LOW>;
 		wakeup-source;
 	};
 
-	button1 {
+	button-1 {
 		label = "menu";
 		linux,code = <KEY_MENU>;
 		gpios = <&gpio1 23 GPIO_ACTIVE_LOW>;
 		wakeup-source;
 	};
 
-	buttons2 {
+	button-2 {
 		label = "power";
 		linux,code = <KEY_POWER>;
 		gpios = <&gpio0 7 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/am335x-phycore-som.dtsi b/arch/arm/boot/dts/am335x-phycore-som.dtsi
index f65cd1331315..e2cec1ffaa4c 100644
--- a/arch/arm/boot/dts/am335x-phycore-som.dtsi
+++ b/arch/arm/boot/dts/am335x-phycore-som.dtsi
@@ -331,7 +331,7 @@
 	pinctrl-0 = <&spi0_pins>;
 	status = "okay";
 
-	serial_flash: m25p80@0 {
+	serial_flash: flash@0 {
 		compatible = "jedec,spi-nor";
 		spi-max-frequency = <48000000>;
 		reg = <0x0>;
diff --git a/arch/arm/boot/dts/am335x-sancloud-bbe-extended-wifi.dts b/arch/arm/boot/dts/am335x-sancloud-bbe-extended-wifi.dts
new file mode 100644
index 000000000000..a2676d10c24a
--- /dev/null
+++ b/arch/arm/boot/dts/am335x-sancloud-bbe-extended-wifi.dts
@@ -0,0 +1,113 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2021 Sancloud Ltd
+ * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ */
+/dts-v1/;
+
+#include "am33xx.dtsi"
+#include "am335x-bone-common.dtsi"
+#include "am335x-boneblack-common.dtsi"
+#include "am335x-sancloud-bbe-common.dtsi"
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	model = "SanCloud BeagleBone Enhanced Extended WiFi";
+	compatible = "sancloud,am335x-boneenhanced",
+		     "ti,am335x-bone-black",
+		     "ti,am335x-bone",
+		     "ti,am33xx";
+
+	wlan_en_reg: fixedregulator@2 {
+		compatible = "regulator-fixed";
+		regulator-name = "wlan-en-regulator";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		startup-delay-us = <100000>;
+	};
+};
+
+&am33xx_pinmux {
+	mmc3_pins: pinmux_mmc3_pins {
+		pinctrl-single,pins = <
+			/* gpmc_a9.gpio1_25: RADIO_EN */
+			AM33XX_PADCONF(AM335X_PIN_GPMC_A9, PIN_OUTPUT_PULLUP, MUX_MODE7)
+
+			/* gpmc_ad12.mmc2_dat0 */
+			AM33XX_PADCONF(AM335X_PIN_GPMC_AD12, PIN_INPUT_PULLUP, MUX_MODE3)
+
+			/* gpmc_ad13.mmc2_dat1 */
+			AM33XX_PADCONF(AM335X_PIN_GPMC_AD13, PIN_INPUT_PULLUP, MUX_MODE3)
+
+			/* gpmc_ad14.mmc2_dat2 */
+			AM33XX_PADCONF(AM335X_PIN_GPMC_AD14, PIN_INPUT_PULLUP, MUX_MODE3)
+
+			/* gpmc_ad15.mmc2_dat3 */
+			AM33XX_PADCONF(AM335X_PIN_GPMC_AD15, PIN_INPUT_PULLUP, MUX_MODE3)
+
+			/* gpmc_csn3.mmc2_cmd */
+			AM33XX_PADCONF(AM335X_PIN_GPMC_CSN3, PIN_INPUT_PULLUP, MUX_MODE3)
+
+			/* gpmc_clk.mmc2_clk */
+			AM33XX_PADCONF(AM335X_PIN_GPMC_CLK, PIN_INPUT_PULLUP, MUX_MODE3)
+		>;
+	};
+
+	bluetooth_pins: pinmux_bluetooth_pins {
+		pinctrl-single,pins = <
+			/* event_intr0.gpio0_19 */
+			AM33XX_PADCONF(AM335X_PIN_XDMA_EVENT_INTR0, PIN_INPUT_PULLUP, MUX_MODE7)
+		>;
+	};
+
+	uart1_pins: pinmux_uart1_pins {
+		pinctrl-single,pins = <
+			/* uart1_rxd */
+			AM33XX_PADCONF(AM335X_PIN_UART1_RXD, PIN_INPUT, MUX_MODE0)
+
+			/* uart1_txd */
+			AM33XX_PADCONF(AM335X_PIN_UART1_TXD, PIN_INPUT, MUX_MODE0)
+
+			/* uart1_ctsn */
+			AM33XX_PADCONF(AM335X_PIN_UART1_CTSN, PIN_INPUT_PULLDOWN, MUX_MODE0)
+
+			/* uart1_rtsn */
+			AM33XX_PADCONF(AM335X_PIN_UART1_RTSN, PIN_OUTPUT_PULLDOWN, MUX_MODE0)
+		>;
+	};
+};
+
+&i2c2 {
+	status = "disabled";
+};
+
+&mmc3 {
+	status = "okay";
+	vmmc-supply = <&wlan_en_reg>;
+	bus-width = <4>;
+	non-removable;
+	cap-power-off-card;
+	ti,needs-special-hs-handling;
+	keep-power-in-suspend;
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc3_pins>;
+	dmas = <&edma_xbar 12 0 1
+		&edma_xbar 13 0 2>;
+	dma-names = "tx", "rx";
+	clock-frequency = <50000000>;
+	max-frequency = <50000000>;
+};
+
+&uart1 {
+	status = "okay";
+
+	bluetooth {
+		pinctrl-names = "default";
+		pinctrl-0 = <&uart1_pins &bluetooth_pins>;
+		compatible = "qcom,qca6174-bt";
+		enable-gpios = <&gpio1 25 GPIO_ACTIVE_HIGH>;
+		clocks = <&l4ls_clkctrl AM3_L4LS_UART2_CLKCTRL 0>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <19 IRQ_TYPE_EDGE_RISING>;
+	};
+};
diff --git a/arch/arm/boot/dts/am335x-shc.dts b/arch/arm/boot/dts/am335x-shc.dts
index 6b9877560741..c497200f9cb0 100644
--- a/arch/arm/boot/dts/am335x-shc.dts
+++ b/arch/arm/boot/dts/am335x-shc.dts
@@ -36,10 +36,10 @@
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
-		back_button {
+		back-button {
 			label = "Back Button";
 			gpios = <&gpio1 29 GPIO_ACTIVE_HIGH>;
 			linux,code = <KEY_BACK>;
@@ -47,7 +47,7 @@
 			wakeup-source;
 		};
 
-		front_button {
+		front-button {
 			label = "Front Button";
 			gpios = <&gpio1 25 GPIO_ACTIVE_HIGH>;
 			linux,code = <KEY_FRONT>;
diff --git a/arch/arm/boot/dts/am335x-sl50.dts b/arch/arm/boot/dts/am335x-sl50.dts
index 6516907ed579..73b5d1a024bd 100644
--- a/arch/arm/boot/dts/am335x-sl50.dts
+++ b/arch/arm/boot/dts/am335x-sl50.dts
@@ -588,7 +588,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&spi0_pins>;
 
-	flash: n25q032@1 {
+	flash: flash@1 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "micron,n25q032";
diff --git a/arch/arm/boot/dts/am335x-wega.dtsi b/arch/arm/boot/dts/am335x-wega.dtsi
index 673159d93a6a..f957fea8208e 100644
--- a/arch/arm/boot/dts/am335x-wega.dtsi
+++ b/arch/arm/boot/dts/am335x-wega.dtsi
@@ -55,7 +55,7 @@
 		2 1 0 0 /* # 0: INACTIVE, 1: TX, 2: RX */
 	>;
 	tx-num-evt = <16>;
-	rt-num-evt = <16>;
+	rx-num-evt = <16>;
 	status = "okay";
 };
 
diff --git a/arch/arm/boot/dts/am33xx-clocks.dtsi b/arch/arm/boot/dts/am33xx-clocks.dtsi
index b7b7106f2dee..d34483ae1778 100644
--- a/arch/arm/boot/dts/am33xx-clocks.dtsi
+++ b/arch/arm/boot/dts/am33xx-clocks.dtsi
@@ -5,251 +5,288 @@
  * Copyright (C) 2013 Texas Instruments, Inc.
  */
 &scm_clocks {
-	sys_clkin_ck: sys_clkin_ck@40 {
+	sys_clkin_ck: clock-sys-clkin-22@40 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "sys_clkin_ck";
 		clocks = <&virt_19200000_ck>, <&virt_24000000_ck>, <&virt_25000000_ck>, <&virt_26000000_ck>;
 		ti,bit-shift = <22>;
 		reg = <0x0040>;
 	};
 
-	adc_tsc_fck: adc_tsc_fck {
+	adc_tsc_fck: clock-adc-tsc-fck {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "adc_tsc_fck";
 		clocks = <&sys_clkin_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	dcan0_fck: dcan0_fck {
+	dcan0_fck: clock-dcan0-fck {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "dcan0_fck";
 		clocks = <&sys_clkin_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	dcan1_fck: dcan1_fck {
+	dcan1_fck: clock-dcan1-fck {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "dcan1_fck";
 		clocks = <&sys_clkin_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	mcasp0_fck: mcasp0_fck {
+	mcasp0_fck: clock-mcasp0-fck {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "mcasp0_fck";
 		clocks = <&sys_clkin_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	mcasp1_fck: mcasp1_fck {
+	mcasp1_fck: clock-mcasp1-fck {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "mcasp1_fck";
 		clocks = <&sys_clkin_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	smartreflex0_fck: smartreflex0_fck {
+	smartreflex0_fck: clock-smartreflex0-fck {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "smartreflex0_fck";
 		clocks = <&sys_clkin_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	smartreflex1_fck: smartreflex1_fck {
+	smartreflex1_fck: clock-smartreflex1-fck {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "smartreflex1_fck";
 		clocks = <&sys_clkin_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	sha0_fck: sha0_fck {
+	sha0_fck: clock-sha0-fck {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "sha0_fck";
 		clocks = <&sys_clkin_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	aes0_fck: aes0_fck {
+	aes0_fck: clock-aes0-fck {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "aes0_fck";
 		clocks = <&sys_clkin_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	rng_fck: rng_fck {
+	rng_fck: clock-rng-fck {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "rng_fck";
 		clocks = <&sys_clkin_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	ehrpwm0_tbclk: ehrpwm0_tbclk@44e10664 {
-		#clock-cells = <0>;
-		compatible = "ti,gate-clock";
-		clocks = <&l4ls_gclk>;
-		ti,bit-shift = <0>;
-		reg = <0x0664>;
-	};
+	clock@664 {
+		compatible = "ti,clksel";
+		reg = <0x664>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
 
-	ehrpwm1_tbclk: ehrpwm1_tbclk@44e10664 {
-		#clock-cells = <0>;
-		compatible = "ti,gate-clock";
-		clocks = <&l4ls_gclk>;
-		ti,bit-shift = <1>;
-		reg = <0x0664>;
-	};
+		ehrpwm0_tbclk: clock-ehrpwm0-tbclk {
+			#clock-cells = <0>;
+			compatible = "ti,gate-clock";
+			clock-output-names = "ehrpwm0_tbclk";
+			clocks = <&l4ls_gclk>;
+			ti,bit-shift = <0>;
+		};
 
-	ehrpwm2_tbclk: ehrpwm2_tbclk@44e10664 {
-		#clock-cells = <0>;
-		compatible = "ti,gate-clock";
-		clocks = <&l4ls_gclk>;
-		ti,bit-shift = <2>;
-		reg = <0x0664>;
+		ehrpwm1_tbclk: clock-ehrpwm1-tbclk {
+			#clock-cells = <0>;
+			compatible = "ti,gate-clock";
+			clock-output-names = "ehrpwm1_tbclk";
+			clocks = <&l4ls_gclk>;
+			ti,bit-shift = <1>;
+		};
+
+		ehrpwm2_tbclk: clock-ehrpwm2-tbclk {
+			#clock-cells = <0>;
+			compatible = "ti,gate-clock";
+			clock-output-names = "ehrpwm2_tbclk";
+			clocks = <&l4ls_gclk>;
+			ti,bit-shift = <2>;
+		};
 	};
 };
 &prcm_clocks {
-	clk_32768_ck: clk_32768_ck {
+	clk_32768_ck: clock-clk-32768 {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "clk_32768_ck";
 		clock-frequency = <32768>;
 	};
 
-	clk_rc32k_ck: clk_rc32k_ck {
+	clk_rc32k_ck: clock-clk-rc32k {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "clk_rc32k_ck";
 		clock-frequency = <32000>;
 	};
 
-	virt_19200000_ck: virt_19200000_ck {
+	virt_19200000_ck: clock-virt-19200000 {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "virt_19200000_ck";
 		clock-frequency = <19200000>;
 	};
 
-	virt_24000000_ck: virt_24000000_ck {
+	virt_24000000_ck: clock-virt-24000000 {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "virt_24000000_ck";
 		clock-frequency = <24000000>;
 	};
 
-	virt_25000000_ck: virt_25000000_ck {
+	virt_25000000_ck: clock-virt-25000000 {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "virt_25000000_ck";
 		clock-frequency = <25000000>;
 	};
 
-	virt_26000000_ck: virt_26000000_ck {
+	virt_26000000_ck: clock-virt-26000000 {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "virt_26000000_ck";
 		clock-frequency = <26000000>;
 	};
 
-	tclkin_ck: tclkin_ck {
+	tclkin_ck: clock-tclkin {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "tclkin_ck";
 		clock-frequency = <12000000>;
 	};
 
-	dpll_core_ck: dpll_core_ck@490 {
+	dpll_core_ck: clock@490 {
 		#clock-cells = <0>;
 		compatible = "ti,am3-dpll-core-clock";
+		clock-output-names = "dpll_core_ck";
 		clocks = <&sys_clkin_ck>, <&sys_clkin_ck>;
 		reg = <0x0490>, <0x045c>, <0x0468>, <0x0460>, <0x0464>;
 	};
 
-	dpll_core_x2_ck: dpll_core_x2_ck {
+	dpll_core_x2_ck: clock-dpll-core-x2 {
 		#clock-cells = <0>;
 		compatible = "ti,am3-dpll-x2-clock";
+		clock-output-names = "dpll_core_x2_ck";
 		clocks = <&dpll_core_ck>;
 	};
 
-	dpll_core_m4_ck: dpll_core_m4_ck@480 {
+	dpll_core_m4_ck: clock-dpll-core-m4@480 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_core_m4_ck";
 		clocks = <&dpll_core_x2_ck>;
 		ti,max-div = <31>;
 		reg = <0x0480>;
 		ti,index-starts-at-one;
 	};
 
-	dpll_core_m5_ck: dpll_core_m5_ck@484 {
+	dpll_core_m5_ck: clock-dpll-core-m5@484 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_core_m5_ck";
 		clocks = <&dpll_core_x2_ck>;
 		ti,max-div = <31>;
 		reg = <0x0484>;
 		ti,index-starts-at-one;
 	};
 
-	dpll_core_m6_ck: dpll_core_m6_ck@4d8 {
+	dpll_core_m6_ck: clock-dpll-core-m6@4d8 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_core_m6_ck";
 		clocks = <&dpll_core_x2_ck>;
 		ti,max-div = <31>;
 		reg = <0x04d8>;
 		ti,index-starts-at-one;
 	};
 
-	dpll_mpu_ck: dpll_mpu_ck@488 {
+	dpll_mpu_ck: clock@488 {
 		#clock-cells = <0>;
 		compatible = "ti,am3-dpll-clock";
+		clock-output-names = "dpll_mpu_ck";
 		clocks = <&sys_clkin_ck>, <&sys_clkin_ck>;
 		reg = <0x0488>, <0x0420>, <0x042c>, <0x0424>, <0x0428>;
 	};
 
-	dpll_mpu_m2_ck: dpll_mpu_m2_ck@4a8 {
+	dpll_mpu_m2_ck: clock-dpll-mpu-m2@4a8 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_mpu_m2_ck";
 		clocks = <&dpll_mpu_ck>;
 		ti,max-div = <31>;
 		reg = <0x04a8>;
 		ti,index-starts-at-one;
 	};
 
-	dpll_ddr_ck: dpll_ddr_ck@494 {
+	dpll_ddr_ck: clock@494 {
 		#clock-cells = <0>;
 		compatible = "ti,am3-dpll-no-gate-clock";
+		clock-output-names = "dpll_ddr_ck";
 		clocks = <&sys_clkin_ck>, <&sys_clkin_ck>;
 		reg = <0x0494>, <0x0434>, <0x0440>, <0x0438>, <0x043c>;
 	};
 
-	dpll_ddr_m2_ck: dpll_ddr_m2_ck@4a0 {
+	dpll_ddr_m2_ck: clock-dpll-ddr-m2@4a0 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_ddr_m2_ck";
 		clocks = <&dpll_ddr_ck>;
 		ti,max-div = <31>;
 		reg = <0x04a0>;
 		ti,index-starts-at-one;
 	};
 
-	dpll_ddr_m2_div2_ck: dpll_ddr_m2_div2_ck {
+	dpll_ddr_m2_div2_ck: clock-dpll-ddr-m2-div2 {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "dpll_ddr_m2_div2_ck";
 		clocks = <&dpll_ddr_m2_ck>;
 		clock-mult = <1>;
 		clock-div = <2>;
 	};
 
-	dpll_disp_ck: dpll_disp_ck@498 {
+	dpll_disp_ck: clock@498 {
 		#clock-cells = <0>;
 		compatible = "ti,am3-dpll-no-gate-clock";
+		clock-output-names = "dpll_disp_ck";
 		clocks = <&sys_clkin_ck>, <&sys_clkin_ck>;
 		reg = <0x0498>, <0x0448>, <0x0454>, <0x044c>, <0x0450>;
 	};
 
-	dpll_disp_m2_ck: dpll_disp_m2_ck@4a4 {
+	dpll_disp_m2_ck: clock-dpll-disp-m2@4a4 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_disp_m2_ck";
 		clocks = <&dpll_disp_ck>;
 		ti,max-div = <31>;
 		reg = <0x04a4>;
@@ -257,418 +294,484 @@
 		ti,set-rate-parent;
 	};
 
-	dpll_per_ck: dpll_per_ck@48c {
+	dpll_per_ck: clock@48c {
 		#clock-cells = <0>;
 		compatible = "ti,am3-dpll-no-gate-j-type-clock";
+		clock-output-names = "dpll_per_ck";
 		clocks = <&sys_clkin_ck>, <&sys_clkin_ck>;
 		reg = <0x048c>, <0x0470>, <0x049c>, <0x0474>, <0x0478>;
 	};
 
-	dpll_per_m2_ck: dpll_per_m2_ck@4ac {
+	dpll_per_m2_ck: clock-dpll-per-m2@4ac {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_per_m2_ck";
 		clocks = <&dpll_per_ck>;
 		ti,max-div = <31>;
 		reg = <0x04ac>;
 		ti,index-starts-at-one;
 	};
 
-	dpll_per_m2_div4_wkupdm_ck: dpll_per_m2_div4_wkupdm_ck {
+	dpll_per_m2_div4_wkupdm_ck: clock-dpll-per-m2-div4-wkupdm {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "dpll_per_m2_div4_wkupdm_ck";
 		clocks = <&dpll_per_m2_ck>;
 		clock-mult = <1>;
 		clock-div = <4>;
 	};
 
-	dpll_per_m2_div4_ck: dpll_per_m2_div4_ck {
+	dpll_per_m2_div4_ck: clock-dpll-per-m2-div4 {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "dpll_per_m2_div4_ck";
 		clocks = <&dpll_per_m2_ck>;
 		clock-mult = <1>;
 		clock-div = <4>;
 	};
 
-	clk_24mhz: clk_24mhz {
+	clk_24mhz: clock-clk-24mhz {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "clk_24mhz";
 		clocks = <&dpll_per_m2_ck>;
 		clock-mult = <1>;
 		clock-div = <8>;
 	};
 
-	clkdiv32k_ck: clkdiv32k_ck {
+	clkdiv32k_ck: clock-clkdiv32k {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "clkdiv32k_ck";
 		clocks = <&clk_24mhz>;
 		clock-mult = <1>;
 		clock-div = <732>;
 	};
 
-	l3_gclk: l3_gclk {
+	l3_gclk: clock-l3-gclk {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "l3_gclk";
 		clocks = <&dpll_core_m4_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	pruss_ocp_gclk: pruss_ocp_gclk@530 {
+	pruss_ocp_gclk: clock-pruss-ocp-gclk@530 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "pruss_ocp_gclk";
 		clocks = <&l3_gclk>, <&dpll_disp_m2_ck>;
 		reg = <0x0530>;
 	};
 
-	mmu_fck: mmu_fck@914 {
+	mmu_fck: clock-mmu-fck-1@914 {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
+		clock-output-names = "mmu_fck";
 		clocks = <&dpll_core_m4_ck>;
 		ti,bit-shift = <1>;
 		reg = <0x0914>;
 	};
 
-	timer1_fck: timer1_fck@528 {
+	timer1_fck: clock-timer1-fck@528 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "timer1_fck";
 		clocks = <&sys_clkin_ck>, <&clk_24mhz_clkctrl AM3_CLK_24MHZ_CLKDIV32K_CLKCTRL 0>, <&tclkin_ck>, <&clk_rc32k_ck>, <&clk_32768_ck>;
 		reg = <0x0528>;
 	};
 
-	timer2_fck: timer2_fck@508 {
+	timer2_fck: clock-timer2-fck@508 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "timer2_fck";
 		clocks = <&tclkin_ck>, <&sys_clkin_ck>, <&clk_24mhz_clkctrl AM3_CLK_24MHZ_CLKDIV32K_CLKCTRL 0>;
 		reg = <0x0508>;
 	};
 
-	timer3_fck: timer3_fck@50c {
+	timer3_fck: clock-timer3-fck@50c {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "timer3_fck";
 		clocks = <&tclkin_ck>, <&sys_clkin_ck>, <&clk_24mhz_clkctrl AM3_CLK_24MHZ_CLKDIV32K_CLKCTRL 0>;
 		reg = <0x050c>;
 	};
 
-	timer4_fck: timer4_fck@510 {
+	timer4_fck: clock-timer4-fck@510 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "timer4_fck";
 		clocks = <&tclkin_ck>, <&sys_clkin_ck>, <&clk_24mhz_clkctrl AM3_CLK_24MHZ_CLKDIV32K_CLKCTRL 0>;
 		reg = <0x0510>;
 	};
 
-	timer5_fck: timer5_fck@518 {
+	timer5_fck: clock-timer5-fck@518 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "timer5_fck";
 		clocks = <&tclkin_ck>, <&sys_clkin_ck>, <&clk_24mhz_clkctrl AM3_CLK_24MHZ_CLKDIV32K_CLKCTRL 0>;
 		reg = <0x0518>;
 	};
 
-	timer6_fck: timer6_fck@51c {
+	timer6_fck: clock-timer6-fck@51c {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "timer6_fck";
 		clocks = <&tclkin_ck>, <&sys_clkin_ck>, <&clk_24mhz_clkctrl AM3_CLK_24MHZ_CLKDIV32K_CLKCTRL 0>;
 		reg = <0x051c>;
 	};
 
-	timer7_fck: timer7_fck@504 {
+	timer7_fck: clock-timer7-fck@504 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "timer7_fck";
 		clocks = <&tclkin_ck>, <&sys_clkin_ck>, <&clk_24mhz_clkctrl AM3_CLK_24MHZ_CLKDIV32K_CLKCTRL 0>;
 		reg = <0x0504>;
 	};
 
-	usbotg_fck: usbotg_fck@47c {
+	usbotg_fck: clock-usbotg-fck-8@47c {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
+		clock-output-names = "usbotg_fck";
 		clocks = <&dpll_per_ck>;
 		ti,bit-shift = <8>;
 		reg = <0x047c>;
 	};
 
-	dpll_core_m4_div2_ck: dpll_core_m4_div2_ck {
+	dpll_core_m4_div2_ck: clock-dpll-core-m4-div2 {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "dpll_core_m4_div2_ck";
 		clocks = <&dpll_core_m4_ck>;
 		clock-mult = <1>;
 		clock-div = <2>;
 	};
 
-	ieee5000_fck: ieee5000_fck@e4 {
+	ieee5000_fck: clock-ieee5000-fck-1@e4 {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
+		clock-output-names = "ieee5000_fck";
 		clocks = <&dpll_core_m4_div2_ck>;
 		ti,bit-shift = <1>;
 		reg = <0x00e4>;
 	};
 
-	wdt1_fck: wdt1_fck@538 {
+	wdt1_fck: clock-wdt1-fck@538 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "wdt1_fck";
 		clocks = <&clk_rc32k_ck>, <&clk_24mhz_clkctrl AM3_CLK_24MHZ_CLKDIV32K_CLKCTRL 0>;
 		reg = <0x0538>;
 	};
 
-	l4_rtc_gclk: l4_rtc_gclk {
+	l4_rtc_gclk: clock-l4-rtc-gclk {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "l4_rtc_gclk";
 		clocks = <&dpll_core_m4_ck>;
 		clock-mult = <1>;
 		clock-div = <2>;
 	};
 
-	l4hs_gclk: l4hs_gclk {
+	l4hs_gclk: clock-l4hs-gclk {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "l4hs_gclk";
 		clocks = <&dpll_core_m4_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	l3s_gclk: l3s_gclk {
+	l3s_gclk: clock-l3s-gclk {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "l3s_gclk";
 		clocks = <&dpll_core_m4_div2_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	l4fw_gclk: l4fw_gclk {
+	l4fw_gclk: clock-l4fw-gclk {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "l4fw_gclk";
 		clocks = <&dpll_core_m4_div2_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	l4ls_gclk: l4ls_gclk {
+	l4ls_gclk: clock-l4ls-gclk {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "l4ls_gclk";
 		clocks = <&dpll_core_m4_div2_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	sysclk_div_ck: sysclk_div_ck {
+	sysclk_div_ck: clock-sysclk-div {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "sysclk_div_ck";
 		clocks = <&dpll_core_m4_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	cpsw_125mhz_gclk: cpsw_125mhz_gclk {
+	cpsw_125mhz_gclk: clock-cpsw-125mhz-gclk {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "cpsw_125mhz_gclk";
 		clocks = <&dpll_core_m5_ck>;
 		clock-mult = <1>;
 		clock-div = <2>;
 	};
 
-	cpsw_cpts_rft_clk: cpsw_cpts_rft_clk@520 {
+	cpsw_cpts_rft_clk: clock-cpsw-cpts-rft@520 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "cpsw_cpts_rft_clk";
 		clocks = <&dpll_core_m5_ck>, <&dpll_core_m4_ck>;
 		reg = <0x0520>;
 	};
 
-	gpio0_dbclk_mux_ck: gpio0_dbclk_mux_ck@53c {
+	gpio0_dbclk_mux_ck: clock-gpio0-dbclk-mux@53c {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "gpio0_dbclk_mux_ck";
 		clocks = <&clk_rc32k_ck>, <&clk_32768_ck>, <&clk_24mhz_clkctrl AM3_CLK_24MHZ_CLKDIV32K_CLKCTRL 0>;
 		reg = <0x053c>;
 	};
 
-	lcd_gclk: lcd_gclk@534 {
+	lcd_gclk: clock-lcd-gclk@534 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "lcd_gclk";
 		clocks = <&dpll_disp_m2_ck>, <&dpll_core_m5_ck>, <&dpll_per_m2_ck>;
 		reg = <0x0534>;
 		ti,set-rate-parent;
 	};
 
-	mmc_clk: mmc_clk {
+	mmc_clk: clock-mmc {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "mmc_clk";
 		clocks = <&dpll_per_m2_ck>;
 		clock-mult = <1>;
 		clock-div = <2>;
 	};
 
-	gfx_fclk_clksel_ck: gfx_fclk_clksel_ck@52c {
-		#clock-cells = <0>;
-		compatible = "ti,mux-clock";
-		clocks = <&dpll_core_m4_ck>, <&dpll_per_m2_ck>;
-		ti,bit-shift = <1>;
-		reg = <0x052c>;
-	};
+	clock@52c {
+		compatible = "ti,clksel";
+		reg = <0x52c>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
 
-	gfx_fck_div_ck: gfx_fck_div_ck@52c {
-		#clock-cells = <0>;
-		compatible = "ti,divider-clock";
-		clocks = <&gfx_fclk_clksel_ck>;
-		reg = <0x052c>;
-		ti,max-div = <2>;
-	};
+		gfx_fclk_clksel_ck: clock-gfx-fclk-clksel {
+			#clock-cells = <0>;
+			compatible = "ti,mux-clock";
+			clock-output-names = "gfx_fclk_clksel_ck";
+			clocks = <&dpll_core_m4_ck>, <&dpll_per_m2_ck>;
+			ti,bit-shift = <1>;
+		};
 
-	sysclkout_pre_ck: sysclkout_pre_ck@700 {
-		#clock-cells = <0>;
-		compatible = "ti,mux-clock";
-		clocks = <&clk_32768_ck>, <&l3_gclk>, <&dpll_ddr_m2_ck>, <&dpll_per_m2_ck>, <&lcd_gclk>;
-		reg = <0x0700>;
+		gfx_fck_div_ck: clock-gfx-fck-div {
+			#clock-cells = <0>;
+			compatible = "ti,divider-clock";
+			clock-output-names = "gfx_fck_div_ck";
+			clocks = <&gfx_fclk_clksel_ck>;
+			ti,max-div = <2>;
+		};
 	};
 
-	clkout2_div_ck: clkout2_div_ck@700 {
-		#clock-cells = <0>;
-		compatible = "ti,divider-clock";
-		clocks = <&sysclkout_pre_ck>;
-		ti,bit-shift = <3>;
-		ti,max-div = <8>;
-		reg = <0x0700>;
-	};
+	clock@700 {
+		compatible = "ti,clksel";
+		reg = <0x700>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
 
-	clkout2_ck: clkout2_ck@700 {
-		#clock-cells = <0>;
-		compatible = "ti,gate-clock";
-		clocks = <&clkout2_div_ck>;
-		ti,bit-shift = <7>;
-		reg = <0x0700>;
+		sysclkout_pre_ck: clock-sysclkout-pre {
+			#clock-cells = <0>;
+			compatible = "ti,mux-clock";
+			clock-output-names = "sysclkout_pre_ck";
+			clocks = <&clk_32768_ck>, <&l3_gclk>, <&dpll_ddr_m2_ck>, <&dpll_per_m2_ck>, <&lcd_gclk>;
+		};
+
+		clkout2_div_ck: clock-clkout2-div {
+			#clock-cells = <0>;
+			compatible = "ti,divider-clock";
+			clock-output-names = "clkout2_div_ck";
+			clocks = <&sysclkout_pre_ck>;
+			ti,bit-shift = <3>;
+			ti,max-div = <8>;
+		};
+
+		clkout2_ck: clock-clkout2 {
+			#clock-cells = <0>;
+			compatible = "ti,gate-clock";
+			clock-output-names = "clkout2_ck";
+			clocks = <&clkout2_div_ck>;
+			ti,bit-shift = <7>;
+		};
 	};
 };
 
 &prcm {
-	per_cm: per-cm@0 {
+	per_cm: clock@0 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "per_cm";
 		reg = <0x0 0x400>;
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0 0x0 0x400>;
 
-		l4ls_clkctrl: l4ls-clkctrl@38 {
+		l4ls_clkctrl: clock@38 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "l4ls_clkctrl";
 			reg = <0x38 0x2c>, <0x6c 0x28>, <0xac 0xc>, <0xc0 0x1c>, <0xec 0xc>, <0x10c 0x8>, <0x130 0x4>;
 			#clock-cells = <2>;
 		};
 
-		l3s_clkctrl: l3s-clkctrl@1c {
+		l3s_clkctrl: clock@1c {
 			compatible = "ti,clkctrl";
+			clock-output-names = "l3s_clkctrl";
 			reg = <0x1c 0x4>, <0x30 0x8>, <0x68 0x4>, <0xf8 0x4>;
 			#clock-cells = <2>;
 		};
 
-		l3_clkctrl: l3-clkctrl@24 {
+		l3_clkctrl: clock@24 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "l3_clkctrl";
 			reg = <0x24 0xc>, <0x94 0x10>, <0xbc 0x4>, <0xdc 0x8>, <0xfc 0x8>;
 			#clock-cells = <2>;
 		};
 
-		l4hs_clkctrl: l4hs-clkctrl@120 {
+		l4hs_clkctrl: clock@120 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "l4hs_clkctrl";
 			reg = <0x120 0x4>;
 			#clock-cells = <2>;
 		};
 
-		pruss_ocp_clkctrl: pruss-ocp-clkctrl@e8 {
+		pruss_ocp_clkctrl: clock@e8 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "pruss_ocp_clkctrl";
 			reg = <0xe8 0x4>;
 			#clock-cells = <2>;
 		};
 
-		cpsw_125mhz_clkctrl: cpsw-125mhz-clkctrl@0 {
+		cpsw_125mhz_clkctrl: clock@0 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "cpsw_125mhz_clkctrl";
 			reg = <0x0 0x18>;
 			#clock-cells = <2>;
 		};
 
-		lcdc_clkctrl: lcdc-clkctrl@18 {
+		lcdc_clkctrl: clock@18 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "lcdc_clkctrl";
 			reg = <0x18 0x4>;
 			#clock-cells = <2>;
 		};
 
-		clk_24mhz_clkctrl: clk-24mhz-clkctrl@14c {
+		clk_24mhz_clkctrl: clock@14c {
 			compatible = "ti,clkctrl";
+			clock-output-names = "clk_24mhz_clkctrl";
 			reg = <0x14c 0x4>;
 			#clock-cells = <2>;
 		};
 	};
 
-	wkup_cm: wkup-cm@400 {
+	wkup_cm: clock@400 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "wkup_cm";
 		reg = <0x400 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0 0x400 0x100>;
 
-		l4_wkup_clkctrl: l4-wkup-clkctrl@0 {
+		l4_wkup_clkctrl: clock@0 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "l4_wkup_clkctrl";
 			reg = <0x0 0x10>, <0xb4 0x24>;
 			#clock-cells = <2>;
 		};
 
-		l3_aon_clkctrl: l3-aon-clkctrl@14 {
+		l3_aon_clkctrl: clock@14 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "l3_aon_clkctrl";
 			reg = <0x14 0x4>;
 			#clock-cells = <2>;
 		};
 
-		l4_wkup_aon_clkctrl: l4-wkup-aon-clkctrl@b0 {
+		l4_wkup_aon_clkctrl: clock@b0 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "l4_wkup_aon_clkctrl";
 			reg = <0xb0 0x4>;
 			#clock-cells = <2>;
 		};
 	};
 
-	mpu_cm: mpu-cm@600 {
+	mpu_cm: clock@600 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "mpu_cm";
 		reg = <0x600 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0 0x600 0x100>;
 
-		mpu_clkctrl: mpu-clkctrl@0 {
+		mpu_clkctrl: clock@0 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "mpu_clkctrl";
 			reg = <0x0 0x8>;
 			#clock-cells = <2>;
 		};
 	};
 
-	l4_rtc_cm: l4-rtc-cm@800 {
+	l4_rtc_cm: clock@800 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "l4_rtc_cm";
 		reg = <0x800 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0 0x800 0x100>;
 
-		l4_rtc_clkctrl: l4-rtc-clkctrl@0 {
+		l4_rtc_clkctrl: clock@0 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "l4_rtc_clkctrl";
 			reg = <0x0 0x4>;
 			#clock-cells = <2>;
 		};
 	};
 
-	gfx_l3_cm: gfx-l3-cm@900 {
+	gfx_l3_cm: clock@900 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "gfx_l3_cm";
 		reg = <0x900 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0 0x900 0x100>;
 
-		gfx_l3_clkctrl: gfx-l3-clkctrl@0 {
+		gfx_l3_clkctrl: clock@0 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "gfx_l3_clkctrl";
 			reg = <0x0 0x8>;
 			#clock-cells = <2>;
 		};
 	};
 
-	l4_cefuse_cm: l4-cefuse-cm@a00 {
+	l4_cefuse_cm: clock@a00 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "l4_cefuse_cm";
 		reg = <0xa00 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0 0xa00 0x100>;
 
-		l4_cefuse_clkctrl: l4-cefuse-clkctrl@0 {
+		l4_cefuse_clkctrl: clock@0 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "l4_cefuse_clkctrl";
 			reg = <0x0 0x24>;
 			#clock-cells = <2>;
 		};
diff --git a/arch/arm/boot/dts/am33xx-l4.dtsi b/arch/arm/boot/dts/am33xx-l4.dtsi
index c9629cb5ccd1..7e50fe633d8a 100644
--- a/arch/arm/boot/dts/am33xx-l4.dtsi
+++ b/arch/arm/boot/dts/am33xx-l4.dtsi
@@ -263,6 +263,8 @@
 				compatible = "ti,am3359-tscadc";
 				reg = <0x0 0x1000>;
 				interrupts = <16>;
+				clocks = <&adc_tsc_fck>;
+				clock-names = "fck";
 				status = "disabled";
 				dmas = <&edma 53 0>, <&edma 57 0>;
 				dma-names = "fifo0", "fifo1";
@@ -1500,8 +1502,7 @@
 			mmc1: mmc@0 {
 				compatible = "ti,am335-sdhci";
 				ti,needs-special-reset;
-				dmas = <&edma_xbar 24 0 0
-					&edma_xbar 25 0 0>;
+				dmas = <&edma 24 0>, <&edma 25 0>;
 				dma-names = "tx", "rx";
 				interrupts = <64>;
 				reg = <0x0 0x1000>;
diff --git a/arch/arm/boot/dts/am33xx.dtsi b/arch/arm/boot/dts/am33xx.dtsi
index f6ec85d58dd1..32d397b3950b 100644
--- a/arch/arm/boot/dts/am33xx.dtsi
+++ b/arch/arm/boot/dts/am33xx.dtsi
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Device Tree Source for AM33XX SoC
  *
  * Copyright (C) 2012 Texas Instruments Incorporated - https://www.ti.com/
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2.  This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
  */
 
 #include <dt-bindings/bus/ti-sysc.h>
@@ -461,8 +458,11 @@
 				interrupts = <17>;
 				interrupt-names = "glue";
 				#dma-cells = <2>;
+				/* For backwards compatibility: */
 				#dma-channels = <30>;
+				dma-channels = <30>;
 				#dma-requests = <256>;
+				dma-requests = <256>;
 			};
 		};
 
diff --git a/arch/arm/boot/dts/am3517-evm-ui.dtsi b/arch/arm/boot/dts/am3517-evm-ui.dtsi
index 7d8f32bf70db..75ad42179aee 100644
--- a/arch/arm/boot/dts/am3517-evm-ui.dtsi
+++ b/arch/arm/boot/dts/am3517-evm-ui.dtsi
@@ -70,61 +70,61 @@
 		compatible = "gpio-keys-polled";
 		poll-interval = <100>;
 
-		record {
+		key-record {
 			label = "Record";
 			/* linux,code = <BTN_0>; */
 			gpios = <&tca6416_2 15 GPIO_ACTIVE_LOW>;
 		};
 
-		play {
+		key-play {
 			label = "Play";
 			linux,code = <KEY_PLAY>;
 			gpios = <&tca6416_2 14 GPIO_ACTIVE_LOW>;
 		};
 
-		Stop {
+		key-stop {
 			label = "Stop";
 			linux,code = <KEY_STOP>;
 			gpios = <&tca6416_2 13 GPIO_ACTIVE_LOW>;
 		};
 
-		fwd {
+		key-fwd {
 			label = "FWD";
 			linux,code = <KEY_FASTFORWARD>;
 			gpios = <&tca6416_2 12 GPIO_ACTIVE_LOW>;
 		};
 
-		rwd {
+		key-rwd {
 			label = "RWD";
 			linux,code = <KEY_REWIND>;
 			gpios = <&tca6416_2 11 GPIO_ACTIVE_LOW>;
 		};
 
-		shift {
+		key-shift {
 			label = "Shift";
 			linux,code = <KEY_LEFTSHIFT>;
 			gpios = <&tca6416_2 10 GPIO_ACTIVE_LOW>;
 		};
 
-		Mode {
+		key-mode {
 			label = "Mode";
 			linux,code = <BTN_MODE>;
 			gpios = <&tca6416_2 9 GPIO_ACTIVE_LOW>;
 		};
 
-		Menu {
+		key-menu {
 			label = "Menu";
 			linux,code = <KEY_MENU>;
 			gpios = <&tca6416_2 8 GPIO_ACTIVE_LOW>;
 		};
 
-		Up {
+		key-up {
 			label = "Up";
 			linux,code = <KEY_UP>;
 			gpios = <&tca6416_2 7 GPIO_ACTIVE_LOW>;
 		};
 
-		Down {
+		key-down {
 			label = "Down";
 			linux,code = <KEY_DOWN>;
 			gpios = <&tca6416_2 6 GPIO_ACTIVE_LOW>;
@@ -137,14 +137,14 @@
 	tlv320aic23_1: codec@1a {
 		compatible = "ti,tlv320aic23";
 		reg = <0x1a>;
-		#sound-dai-cells= <0>;
+		#sound-dai-cells = <0>;
 		status = "okay";
 	};
 
 	tlv320aic23_2: codec@1b {
 		compatible = "ti,tlv320aic23";
 		reg = <0x1b>;
-		#sound-dai-cells= <0>;
+		#sound-dai-cells = <0>;
 		status = "okay";
 	};
 };
@@ -154,7 +154,7 @@
 	tlv320aic23_3: codec@1a {
 		compatible = "ti,tlv320aic23";
 		reg = <0x1a>;
-		#sound-dai-cells= <0>;
+		#sound-dai-cells = <0>;
 		status = "okay";
 	};
 
diff --git a/arch/arm/boot/dts/am3517-evm.dts b/arch/arm/boot/dts/am3517-evm.dts
index 0d2fac98ce7d..35b653014f2b 100644
--- a/arch/arm/boot/dts/am3517-evm.dts
+++ b/arch/arm/boot/dts/am3517-evm.dts
@@ -37,55 +37,55 @@
 		compatible = "gpio-keys-polled";
 		poll-interval = <100>;
 
-		user_pb {
+		button-user {
 			label = "User Push Button";
 			linux,code = <BTN_0>;
 			gpios = <&tca6416 5 GPIO_ACTIVE_LOW>;
 		};
 
-		user_sw_1 {
+		switch-1 {
 			label = "User Switch 1";
 			linux,code = <BTN_1>;
 			gpios = <&tca6416 8 GPIO_ACTIVE_LOW>;
 		};
 
-		user_sw_2 {
+		switch-2 {
 			label = "User Switch 2";
 			linux,code = <BTN_2>;
 			gpios = <&tca6416 9 GPIO_ACTIVE_LOW>;
 		};
 
-		user_sw_3 {
+		switch-3 {
 			label = "User Switch 3";
 			linux,code = <BTN_3>;
 			gpios = <&tca6416 10 GPIO_ACTIVE_LOW>;
 		};
 
-		user_sw_4 {
+		switch-4 {
 			label = "User Switch 4";
 			linux,code = <BTN_4>;
 			gpios = <&tca6416 11 GPIO_ACTIVE_LOW>;
 		};
 
-		user_sw_5 {
+		switch-5 {
 			label = "User Switch 5";
 			linux,code = <BTN_5>;
 			gpios = <&tca6416 12 GPIO_ACTIVE_LOW>;
 		};
 
-		user_sw_6 {
+		switch-6 {
 			label = "User Switch 6";
 			linux,code = <BTN_6>;
 			gpios = <&tca6416 13 GPIO_ACTIVE_LOW>;
 		};
 
-		user_sw_7 {
+		switch-7 {
 			label = "User Switch 7";
 			linux,code = <BTN_7>;
 			gpios = <&tca6416 14 GPIO_ACTIVE_LOW>;
 		};
 
-		user_sw_8 {
+		switch-8 {
 			label = "User Switch 8";
 			linux,code = <BTN_8>;
 			gpios = <&tca6416 15 GPIO_ACTIVE_LOW>;
@@ -161,6 +161,8 @@
 
 	/* HS USB Host PHY on PORT 1 */
 	hsusb1_phy: hsusb1_phy {
+		pinctrl-names = "default";
+		pinctrl-0 = <&hsusb1_rst_pins>;
 		compatible = "usb-nop-xceiv";
 		reset-gpios = <&gpio2 25 GPIO_ACTIVE_LOW>; /* gpio_57 */
 		#phy-cells = <0>;
@@ -168,7 +170,9 @@
 };
 
 &davinci_emac {
-	     status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&ethernet_pins>;
+	status = "okay";
 };
 
 &davinci_mdio {
@@ -193,6 +197,8 @@
 };
 
 &i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2_pins>;
 	clock-frequency = <400000>;
 	/* User DIP swithes [1:8] / User LEDS [1:2] */
 	tca6416: gpio@21 {
@@ -205,6 +211,8 @@
 };
 
 &i2c3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c3_pins>;
 	clock-frequency = <400000>;
 };
 
@@ -223,6 +231,8 @@
 };
 
 &usbhshost {
+	pinctrl-names = "default";
+	pinctrl-0 = <&hsusb1_pins>;
 	port1-mode = "ehci-phy";
 };
 
@@ -231,8 +241,35 @@
 };
 
 &omap3_pmx_core {
-	pinctrl-names = "default";
-	pinctrl-0 = <&hsusb1_rst_pins>;
+
+	ethernet_pins: pinmux_ethernet_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x21fe, PIN_INPUT | MUX_MODE0) /* rmii_mdio_data */
+			OMAP3_CORE1_IOPAD(0x2200, MUX_MODE0) /* rmii_mdio_clk */
+			OMAP3_CORE1_IOPAD(0x2202, PIN_INPUT_PULLDOWN | MUX_MODE0) /* rmii_rxd0 */
+			OMAP3_CORE1_IOPAD(0x2204, PIN_INPUT_PULLDOWN | MUX_MODE0) /* rmii_rxd1 */
+			OMAP3_CORE1_IOPAD(0x2206, PIN_INPUT_PULLDOWN | MUX_MODE0) /* rmii_crs_dv */
+			OMAP3_CORE1_IOPAD(0x2208, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* rmii_rxer */
+			OMAP3_CORE1_IOPAD(0x220a, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* rmii_txd0 */
+			OMAP3_CORE1_IOPAD(0x220c, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* rmii_txd1 */
+			OMAP3_CORE1_IOPAD(0x220e, PIN_OUTPUT_PULLDOWN |MUX_MODE0) /* rmii_txen */
+			OMAP3_CORE1_IOPAD(0x2210, PIN_INPUT_PULLDOWN | MUX_MODE0) /* rmii_50mhz_clk */
+		>;
+	};
+
+	i2c2_pins: pinmux_i2c2_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x21be, PIN_INPUT_PULLUP | MUX_MODE0)  /* i2c2_scl */
+			OMAP3_CORE1_IOPAD(0x21c0, PIN_INPUT_PULLUP | MUX_MODE0)  /* i2c2_sda */
+		>;
+	};
+
+	i2c3_pins: pinmux_i2c3_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x21c2, PIN_INPUT_PULLUP | MUX_MODE0)  /* i2c3_scl */
+			OMAP3_CORE1_IOPAD(0x21c4, PIN_INPUT_PULLUP | MUX_MODE0)  /* i2c3_sda */
+		>;
+	};
 
 	leds_pins: pinmux_leds_pins {
 		pinctrl-single,pins = <
@@ -300,8 +337,6 @@
 };
 
 &omap3_pmx_core2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&hsusb1_pins>;
 
 	hsusb1_pins: pinmux_hsusb1_pins {
 		pinctrl-single,pins = <
diff --git a/arch/arm/boot/dts/am3517-som.dtsi b/arch/arm/boot/dts/am3517-som.dtsi
index 8b669e2eafec..f7b680f6c48a 100644
--- a/arch/arm/boot/dts/am3517-som.dtsi
+++ b/arch/arm/boot/dts/am3517-som.dtsi
@@ -69,6 +69,8 @@
 };
 
 &i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
 	clock-frequency = <400000>;
 
 	s35390a: s35390a@30 {
@@ -179,6 +181,13 @@
 
 &omap3_pmx_core {
 
+	i2c1_pins: pinmux_i2c1_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x21ba, PIN_INPUT_PULLUP | MUX_MODE0)  /* i2c1_scl */
+			OMAP3_CORE1_IOPAD(0x21bc, PIN_INPUT_PULLUP | MUX_MODE0)  /* i2c1_sda */
+		>;
+	};
+
 	wl12xx_buffer_pins: pinmux_wl12xx_buffer_pins {
 		pinctrl-single,pins = <
 			OMAP3_CORE1_IOPAD(0x2156, PIN_OUTPUT | MUX_MODE4)  /* mmc1_dat7.gpio_129 */
diff --git a/arch/arm/boot/dts/am3517.dtsi b/arch/arm/boot/dts/am3517.dtsi
index de33c4f89f33..cb316135bc7c 100644
--- a/arch/arm/boot/dts/am3517.dtsi
+++ b/arch/arm/boot/dts/am3517.dtsi
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Device Tree Source for am3517 SoC
  *
  * Copyright (C) 2013 Texas Instruments Incorporated - https://www.ti.com/
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2.  This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
  */
 
 #include "omap3.dtsi"
diff --git a/arch/arm/boot/dts/am35xx-clocks.dtsi b/arch/arm/boot/dts/am35xx-clocks.dtsi
index 220d0a52797e..0ee7afaa0e8e 100644
--- a/arch/arm/boot/dts/am35xx-clocks.dtsi
+++ b/arch/arm/boot/dts/am35xx-clocks.dtsi
@@ -62,12 +62,27 @@
 	};
 };
 &cm_clocks {
-	ipss_ick: ipss_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,am35xx-interface-clock";
-		clocks = <&core_l3_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <4>;
+	clock@a10 {
+		compatible = "ti,clksel";
+		reg = <0xa10>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
+
+		ipss_ick: clock-ipss-ick {
+			#clock-cells = <0>;
+			compatible = "ti,am35xx-interface-clock";
+			clock-output-names = "ipss_ick";
+			clocks = <&core_l3_ick>;
+			ti,bit-shift = <4>;
+		};
+
+		uart4_ick_am35xx: clock-uart4-ick-am35xx {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "uart4_ick_am35xx";
+			clocks = <&core_l4_ick>;
+			ti,bit-shift = <23>;
+		};
 	};
 
 	rmii_ck: rmii_ck {
@@ -82,20 +97,19 @@
 		clock-frequency = <27000000>;
 	};
 
-	uart4_ick_am35xx: uart4_ick_am35xx@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&core_l4_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <23>;
-	};
+	clock@a00 {
+		compatible = "ti,clksel";
+		reg = <0xa00>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
 
-	uart4_fck_am35xx: uart4_fck_am35xx@a00 {
-		#clock-cells = <0>;
-		compatible = "ti,wait-gate-clock";
-		clocks = <&core_48m_fck>;
-		reg = <0x0a00>;
-		ti,bit-shift = <23>;
+		uart4_fck_am35xx: clock-uart4-fck-am35xx {
+			#clock-cells = <0>;
+			compatible = "ti,wait-gate-clock";
+			clock-output-names = "uart4_fck_am35xx";
+			clocks = <&core_48m_fck>;
+			ti,bit-shift = <23>;
+		};
 	};
 };
 
diff --git a/arch/arm/boot/dts/am3874-iceboard.dts b/arch/arm/boot/dts/am3874-iceboard.dts
index 9423e9feaa10..d039af879367 100644
--- a/arch/arm/boot/dts/am3874-iceboard.dts
+++ b/arch/arm/boot/dts/am3874-iceboard.dts
@@ -213,7 +213,7 @@
 
 			u48: pca9575@22 {
 				compatible = "nxp,pca9575";
-				reg=<0x22>;
+				reg = <0x22>;
 				gpio-controller;
 				#gpio-cells = <2>;
 
@@ -232,7 +232,7 @@
 
 			u59: pca9575@23 {
 				compatible = "nxp,pca9575";
-				reg=<0x23>;
+				reg = <0x23>;
 				gpio-controller;
 				#gpio-cells = <2>;
 				gpio-line-names =
@@ -434,7 +434,7 @@
 };
 
 &mcspi1 {
-	s25fl256@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "jedec,spi-nor";
diff --git a/arch/arm/boot/dts/am4372.dtsi b/arch/arm/boot/dts/am4372.dtsi
index 61a1d88f9df6..8613355bbd5e 100644
--- a/arch/arm/boot/dts/am4372.dtsi
+++ b/arch/arm/boot/dts/am4372.dtsi
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Device Tree Source for AM4372 SoC
  *
  * Copyright (C) 2013 Texas Instruments Incorporated - https://www.ti.com/
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2.  This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
  */
 
 #include <dt-bindings/bus/ti-sysc.h>
diff --git a/arch/arm/boot/dts/am437x-cm-t43.dts b/arch/arm/boot/dts/am437x-cm-t43.dts
index 5ce8e684e7d3..0861e868b75a 100644
--- a/arch/arm/boot/dts/am437x-cm-t43.dts
+++ b/arch/arm/boot/dts/am437x-cm-t43.dts
@@ -302,7 +302,7 @@
 		&edma 17 0>;
 	dma-names = "tx0", "rx0";
 
-	flash: w25q64cvzpig@0 {
+	flash: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "jedec,spi-nor";
@@ -399,7 +399,7 @@
 	tsc {
 		ti,wires = <4>;
 		ti,x-plate-resistance = <200>;
-		ti,coordiante-readouts = <5>;
+		ti,coordinate-readouts = <5>;
 		ti,wire-config = <0x00 0x11 0x22 0x33>;
 	};
 
diff --git a/arch/arm/boot/dts/am437x-gp-evm.dts b/arch/arm/boot/dts/am437x-gp-evm.dts
index c2e4896076e7..46d5361fe876 100644
--- a/arch/arm/boot/dts/am437x-gp-evm.dts
+++ b/arch/arm/boot/dts/am437x-gp-evm.dts
@@ -775,6 +775,14 @@
 	};
 };
 
+&magadc {
+	status = "okay";
+
+	adc {
+		ti,adc-channels = <0 1 2 3 4 5 6 7>;
+	};
+};
+
 &ecap0 {
 	status = "okay";
 	pinctrl-names = "default";
@@ -1119,6 +1127,11 @@
 	cpu0-supply = <&dcdc2>;
 };
 
+&wkup_m3_ipc {
+	ti,set-io-isolation;
+	firmware-name = "am43x-evm-scale-data.bin";
+};
+
 &pruss1_mdio {
 	status = "disabled";
 };
diff --git a/arch/arm/boot/dts/am437x-idk-evm.dts b/arch/arm/boot/dts/am437x-idk-evm.dts
index 53f64e3ce735..123a95f87554 100644
--- a/arch/arm/boot/dts/am437x-idk-evm.dts
+++ b/arch/arm/boot/dts/am437x-idk-evm.dts
@@ -98,14 +98,12 @@
 		vin-supply = <&v1_5dreg>;
 	};
 
-	gpio_keys: gpio_keys {
+	gpio_keys: gpio-keys {
 		compatible = "gpio-keys";
 		pinctrl-names = "default";
 		pinctrl-0 = <&gpio_keys_pins_default>;
-		#address-cells = <1>;
-		#size-cells = <0>;
 
-		switch0 {
+		switch-0 {
 			label = "power-button";
 			linux,code = <KEY_POWER>;
 			gpios = <&gpio4 2 GPIO_ACTIVE_LOW>;
@@ -437,7 +435,7 @@
 	pinctrl-1 = <&qspi_pins_sleep>;
 
 	spi-max-frequency = <48000000>;
-	m25p80@0 {
+	flash@0 {
 		compatible = "mx66l51235l";
 		spi-max-frequency = <48000000>;
 		reg = <0>;
diff --git a/arch/arm/boot/dts/am437x-l4.dtsi b/arch/arm/boot/dts/am437x-l4.dtsi
index ba58e6b0da1d..415210b034ef 100644
--- a/arch/arm/boot/dts/am437x-l4.dtsi
+++ b/arch/arm/boot/dts/am437x-l4.dtsi
@@ -2378,11 +2378,38 @@
 		};
 
 		target-module@4c000 {			/* 0x4834c000, ap 114 72.0 */
-			compatible = "ti,sysc";
-			status = "disabled";
+			compatible = "ti,sysc-omap4", "ti,sysc";
+			reg = <0x4c000 0x4>,
+			      <0x4c010 0x4>;
+			reg-names = "rev", "sysc";
+			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>;
+			clocks = <&l3s_clkctrl AM4_L3S_ADC1_CLKCTRL 0>;
+			clock-names = "fck";
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges = <0x0 0x4c000 0x2000>;
+
+			magadc: magadc@0 {
+				compatible = "ti,am4372-magadc";
+				reg = <0x0 0x2000>;
+				interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&adc_mag_fck>;
+				clock-names = "fck";
+				dmas = <&edma 54 0>, <&edma 55 0>;
+				dma-names = "fifo0", "fifo1";
+				status = "disabled";
+
+				mag {
+					compatible = "ti,am4372-mag";
+				};
+
+				adc {
+					#io-channel-cells = <1>;
+					compatible = "ti,am4372-adc";
+				};
+			};
 		};
 
 		target-module@80000 {			/* 0x48380000, ap 123 42.0 */
diff --git a/arch/arm/boot/dts/am437x-sk-evm.dts b/arch/arm/boot/dts/am437x-sk-evm.dts
index 20a34d2d85df..036f3831dc26 100644
--- a/arch/arm/boot/dts/am437x-sk-evm.dts
+++ b/arch/arm/boot/dts/am437x-sk-evm.dts
@@ -746,7 +746,7 @@
 	pinctrl-0 = <&qspi_pins>;
 
 	spi-max-frequency = <48000000>;
-	m25p80@0 {
+	flash@0 {
 		compatible = "mx66l51235l";
 		spi-max-frequency = <48000000>;
 		reg = <0>;
@@ -893,6 +893,10 @@
 	};
 };
 
+&wkup_m3_ipc {
+	firmware-name = "am43x-evm-scale-data.bin";
+};
+
 &pruss1_mdio {
 	status = "disabled";
 };
diff --git a/arch/arm/boot/dts/am43x-epos-evm.dts b/arch/arm/boot/dts/am43x-epos-evm.dts
index 2f4d2e4e9b3e..27f4ce855549 100644
--- a/arch/arm/boot/dts/am43x-epos-evm.dts
+++ b/arch/arm/boot/dts/am43x-epos-evm.dts
@@ -11,7 +11,7 @@
 #include <dt-bindings/pinctrl/am43xx.h>
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/pwm/pwm.h>
-#include <dt-bindings/sound/tlv320aic31xx-micbias.h>
+#include <dt-bindings/sound/tlv320aic31xx.h>
 
 / {
 	model = "TI AM43x EPOS EVM";
@@ -902,7 +902,7 @@
 	pinctrl-1 = <&qspi1_pins_sleep>;
 
 	spi-max-frequency = <48000000>;
-	m25p80@0 {
+	flash@0 {
 		compatible = "mx66l51235l";
 		spi-max-frequency = <48000000>;
 		reg = <0>;
@@ -1019,6 +1019,10 @@
 	cpu0-supply = <&dcdc2>;
 };
 
+&wkup_m3_ipc {
+	firmware-name = "am43x-evm-scale-data.bin";
+};
+
 &pruss1_mdio {
 	status = "disabled";
 };
diff --git a/arch/arm/boot/dts/am43xx-clocks.dtsi b/arch/arm/boot/dts/am43xx-clocks.dtsi
index 314fc5975acb..9a5437b3d6a8 100644
--- a/arch/arm/boot/dts/am43xx-clocks.dtsi
+++ b/arch/arm/boot/dts/am43xx-clocks.dtsi
@@ -5,217 +5,246 @@
  * Copyright (C) 2013 Texas Instruments, Inc.
  */
 &scm_clocks {
-	sys_clkin_ck: sys_clkin_ck@40 {
+	sys_clkin_ck: clock-sys-clkin-31@40 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "sys_clkin_ck";
 		clocks = <&sysboot_freq_sel_ck>, <&crystal_freq_sel_ck>;
 		ti,bit-shift = <31>;
 		reg = <0x0040>;
 	};
 
-	crystal_freq_sel_ck: crystal_freq_sel_ck@40 {
+	crystal_freq_sel_ck: clock-crystal-freq-sel-29@40 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "crystal_freq_sel_ck";
 		clocks = <&virt_19200000_ck>, <&virt_24000000_ck>, <&virt_25000000_ck>, <&virt_26000000_ck>;
 		ti,bit-shift = <29>;
 		reg = <0x0040>;
 	};
 
-	sysboot_freq_sel_ck: sysboot_freq_sel_ck@44e10040 {
+	sysboot_freq_sel_ck: clock-sysboot-freq-sel-22@44e10040 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "sysboot_freq_sel_ck";
 		clocks = <&virt_19200000_ck>, <&virt_24000000_ck>, <&virt_25000000_ck>, <&virt_26000000_ck>;
 		ti,bit-shift = <22>;
 		reg = <0x0040>;
 	};
 
-	adc_tsc_fck: adc_tsc_fck {
+	adc_tsc_fck: clock-adc-tsc-fck {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "adc_tsc_fck";
 		clocks = <&sys_clkin_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	dcan0_fck: dcan0_fck {
+	dcan0_fck: clock-dcan0-fck {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "dcan0_fck";
 		clocks = <&sys_clkin_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	dcan1_fck: dcan1_fck {
+	dcan1_fck: clock-dcan1-fck {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "dcan1_fck";
 		clocks = <&sys_clkin_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	mcasp0_fck: mcasp0_fck {
+	mcasp0_fck: clock-mcasp0-fck {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "mcasp0_fck";
 		clocks = <&sys_clkin_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	mcasp1_fck: mcasp1_fck {
+	mcasp1_fck: clock-mcasp1-fck {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "mcasp1_fck";
 		clocks = <&sys_clkin_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	smartreflex0_fck: smartreflex0_fck {
+	smartreflex0_fck: clock-smartreflex0-fck {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "smartreflex0_fck";
 		clocks = <&sys_clkin_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	smartreflex1_fck: smartreflex1_fck {
+	smartreflex1_fck: clock-smartreflex1-fck {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "smartreflex1_fck";
 		clocks = <&sys_clkin_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	sha0_fck: sha0_fck {
+	sha0_fck: clock-sha0-fck {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "sha0_fck";
 		clocks = <&sys_clkin_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	aes0_fck: aes0_fck {
+	aes0_fck: clock-aes0-fck {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "aes0_fck";
 		clocks = <&sys_clkin_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	rng_fck: rng_fck {
+	rng_fck: clock-rng-fck {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "rng_fck";
 		clocks = <&sys_clkin_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	ehrpwm0_tbclk: ehrpwm0_tbclk@664 {
+	ehrpwm0_tbclk: clock-ehrpwm0-tbclk-0@664 {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
+		clock-output-names = "ehrpwm0_tbclk";
 		clocks = <&l4ls_gclk>;
 		ti,bit-shift = <0>;
 		reg = <0x0664>;
 	};
 
-	ehrpwm1_tbclk: ehrpwm1_tbclk@664 {
+	ehrpwm1_tbclk: clock-ehrpwm1-tbclk-1@664 {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
+		clock-output-names = "ehrpwm1_tbclk";
 		clocks = <&l4ls_gclk>;
 		ti,bit-shift = <1>;
 		reg = <0x0664>;
 	};
 
-	ehrpwm2_tbclk: ehrpwm2_tbclk@664 {
+	ehrpwm2_tbclk: clock-ehrpwm2-tbclk-2@664 {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
+		clock-output-names = "ehrpwm2_tbclk";
 		clocks = <&l4ls_gclk>;
 		ti,bit-shift = <2>;
 		reg = <0x0664>;
 	};
 
-	ehrpwm3_tbclk: ehrpwm3_tbclk@664 {
+	ehrpwm3_tbclk: clock-ehrpwm3-tbclk-4@664 {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
+		clock-output-names = "ehrpwm3_tbclk";
 		clocks = <&l4ls_gclk>;
 		ti,bit-shift = <4>;
 		reg = <0x0664>;
 	};
 
-	ehrpwm4_tbclk: ehrpwm4_tbclk@664 {
+	ehrpwm4_tbclk: clock-ehrpwm4-tbclk-5@664 {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
+		clock-output-names = "ehrpwm4_tbclk";
 		clocks = <&l4ls_gclk>;
 		ti,bit-shift = <5>;
 		reg = <0x0664>;
 	};
 
-	ehrpwm5_tbclk: ehrpwm5_tbclk@664 {
+	ehrpwm5_tbclk: clock-ehrpwm5-tbclk-6@664 {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
+		clock-output-names = "ehrpwm5_tbclk";
 		clocks = <&l4ls_gclk>;
 		ti,bit-shift = <6>;
 		reg = <0x0664>;
 	};
 };
 &prcm_clocks {
-	clk_32768_ck: clk_32768_ck {
+	clk_32768_ck: clock-clk-32768 {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "clk_32768_ck";
 		clock-frequency = <32768>;
 	};
 
-	clk_rc32k_ck: clk_rc32k_ck {
+	clk_rc32k_ck: clock-clk-rc32k {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "clk_rc32k_ck";
 		clock-frequency = <32768>;
 	};
 
-	virt_19200000_ck: virt_19200000_ck {
+	virt_19200000_ck: clock-virt-19200000 {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "virt_19200000_ck";
 		clock-frequency = <19200000>;
 	};
 
-	virt_24000000_ck: virt_24000000_ck {
+	virt_24000000_ck: clock-virt-24000000 {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "virt_24000000_ck";
 		clock-frequency = <24000000>;
 	};
 
-	virt_25000000_ck: virt_25000000_ck {
+	virt_25000000_ck: clock-virt-25000000 {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "virt_25000000_ck";
 		clock-frequency = <25000000>;
 	};
 
-	virt_26000000_ck: virt_26000000_ck {
+	virt_26000000_ck: clock-virt-26000000 {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "virt_26000000_ck";
 		clock-frequency = <26000000>;
 	};
 
-	tclkin_ck: tclkin_ck {
+	tclkin_ck: clock-tclkin {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "tclkin_ck";
 		clock-frequency = <26000000>;
 	};
 
-	dpll_core_ck: dpll_core_ck@2d20 {
+	dpll_core_ck: clock@2d20 {
 		#clock-cells = <0>;
 		compatible = "ti,am3-dpll-core-clock";
+		clock-output-names = "dpll_core_ck";
 		clocks = <&sys_clkin_ck>, <&sys_clkin_ck>;
 		reg = <0x2d20>, <0x2d24>, <0x2d2c>, <0x2d48>, <0x2d4c>;
 	};
 
-	dpll_core_x2_ck: dpll_core_x2_ck {
+	dpll_core_x2_ck: clock-dpll-core-x2 {
 		#clock-cells = <0>;
 		compatible = "ti,am3-dpll-x2-clock";
+		clock-output-names = "dpll_core_x2_ck";
 		clocks = <&dpll_core_ck>;
 	};
 
-	dpll_core_m4_ck: dpll_core_m4_ck@2d38 {
+	dpll_core_m4_ck: clock-dpll-core-m4-8@2d38 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_core_m4_ck";
 		clocks = <&dpll_core_x2_ck>;
 		ti,max-div = <31>;
 		ti,autoidle-shift = <8>;
@@ -224,9 +253,10 @@
 		ti,invert-autoidle-bit;
 	};
 
-	dpll_core_m5_ck: dpll_core_m5_ck@2d3c {
+	dpll_core_m5_ck: clock-dpll-core-m5-8@2d3c {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_core_m5_ck";
 		clocks = <&dpll_core_x2_ck>;
 		ti,max-div = <31>;
 		ti,autoidle-shift = <8>;
@@ -235,9 +265,10 @@
 		ti,invert-autoidle-bit;
 	};
 
-	dpll_core_m6_ck: dpll_core_m6_ck@2d40 {
+	dpll_core_m6_ck: clock-dpll-core-m6-8@2d40 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_core_m6_ck";
 		clocks = <&dpll_core_x2_ck>;
 		ti,max-div = <31>;
 		ti,autoidle-shift = <8>;
@@ -246,16 +277,18 @@
 		ti,invert-autoidle-bit;
 	};
 
-	dpll_mpu_ck: dpll_mpu_ck@2d60 {
+	dpll_mpu_ck: clock@2d60 {
 		#clock-cells = <0>;
 		compatible = "ti,am3-dpll-clock";
+		clock-output-names = "dpll_mpu_ck";
 		clocks = <&sys_clkin_ck>, <&sys_clkin_ck>;
 		reg = <0x2d60>, <0x2d64>, <0x2d6c>, <0x2d88>, <0x2d8c>;
 	};
 
-	dpll_mpu_m2_ck: dpll_mpu_m2_ck@2d70 {
+	dpll_mpu_m2_ck: clock-dpll-mpu-m2-8@2d70 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_mpu_m2_ck";
 		clocks = <&dpll_mpu_ck>;
 		ti,max-div = <31>;
 		ti,autoidle-shift = <8>;
@@ -264,24 +297,27 @@
 		ti,invert-autoidle-bit;
 	};
 
-	mpu_periphclk: mpu_periphclk {
+	mpu_periphclk: clock-mpu-periphclk {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "mpu_periphclk";
 		clocks = <&dpll_mpu_m2_ck>;
 		clock-mult = <1>;
 		clock-div = <2>;
 	};
 
-	dpll_ddr_ck: dpll_ddr_ck@2da0 {
+	dpll_ddr_ck: clock@2da0 {
 		#clock-cells = <0>;
 		compatible = "ti,am3-dpll-clock";
+		clock-output-names = "dpll_ddr_ck";
 		clocks = <&sys_clkin_ck>, <&sys_clkin_ck>;
 		reg = <0x2da0>, <0x2da4>, <0x2dac>, <0x2dc8>, <0x2dcc>;
 	};
 
-	dpll_ddr_m2_ck: dpll_ddr_m2_ck@2db0 {
+	dpll_ddr_m2_ck: clock-dpll-ddr-m2-8@2db0 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_ddr_m2_ck";
 		clocks = <&dpll_ddr_ck>;
 		ti,max-div = <31>;
 		ti,autoidle-shift = <8>;
@@ -290,16 +326,18 @@
 		ti,invert-autoidle-bit;
 	};
 
-	dpll_disp_ck: dpll_disp_ck@2e20 {
+	dpll_disp_ck: clock@2e20 {
 		#clock-cells = <0>;
 		compatible = "ti,am3-dpll-clock";
+		clock-output-names = "dpll_disp_ck";
 		clocks = <&sys_clkin_ck>, <&sys_clkin_ck>;
 		reg = <0x2e20>, <0x2e24>, <0x2e2c>, <0x2e48>, <0x2e4c>;
 	};
 
-	dpll_disp_m2_ck: dpll_disp_m2_ck@2e30 {
+	dpll_disp_m2_ck: clock-dpll-disp-m2-8@2e30 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_disp_m2_ck";
 		clocks = <&dpll_disp_ck>;
 		ti,max-div = <31>;
 		ti,autoidle-shift = <8>;
@@ -309,16 +347,18 @@
 		ti,set-rate-parent;
 	};
 
-	dpll_per_ck: dpll_per_ck@2de0 {
+	dpll_per_ck: clock@2de0 {
 		#clock-cells = <0>;
 		compatible = "ti,am3-dpll-j-type-clock";
+		clock-output-names = "dpll_per_ck";
 		clocks = <&sys_clkin_ck>, <&sys_clkin_ck>;
 		reg = <0x2de0>, <0x2de4>, <0x2dec>, <0x2e08>, <0x2e0c>;
 	};
 
-	dpll_per_m2_ck: dpll_per_m2_ck@2df0 {
+	dpll_per_m2_ck: clock-dpll-per-m2-8@2df0 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_per_m2_ck";
 		clocks = <&dpll_per_ck>;
 		ti,max-div = <127>;
 		ti,autoidle-shift = <8>;
@@ -327,242 +367,281 @@
 		ti,invert-autoidle-bit;
 	};
 
-	dpll_per_m2_div4_wkupdm_ck: dpll_per_m2_div4_wkupdm_ck {
+	dpll_per_m2_div4_wkupdm_ck: clock-dpll-per-m2-div4-wkupdm {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "dpll_per_m2_div4_wkupdm_ck";
 		clocks = <&dpll_per_m2_ck>;
 		clock-mult = <1>;
 		clock-div = <4>;
 	};
 
-	dpll_per_m2_div4_ck: dpll_per_m2_div4_ck {
+	dpll_per_m2_div4_ck: clock-dpll-per-m2-div4 {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "dpll_per_m2_div4_ck";
 		clocks = <&dpll_per_m2_ck>;
 		clock-mult = <1>;
 		clock-div = <4>;
 	};
 
-	clk_24mhz: clk_24mhz {
+	clk_24mhz: clock-clk-24mhz {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "clk_24mhz";
 		clocks = <&dpll_per_m2_ck>;
 		clock-mult = <1>;
 		clock-div = <8>;
 	};
 
-	clkdiv32k_ck: clkdiv32k_ck {
+	clkdiv32k_ck: clock-clkdiv32k {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "clkdiv32k_ck";
 		clocks = <&clk_24mhz>;
 		clock-mult = <1>;
 		clock-div = <732>;
 	};
 
-	clkdiv32k_ick: clkdiv32k_ick@2a38 {
+	clkdiv32k_ick: clock-clkdiv32k-ick-8@2a38 {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
+		clock-output-names = "clkdiv32k_ick";
 		clocks = <&clkdiv32k_ck>;
 		ti,bit-shift = <8>;
 		reg = <0x2a38>;
 	};
 
-	sysclk_div: sysclk_div {
+	sysclk_div: clock-sysclk-div {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "sysclk_div";
 		clocks = <&dpll_core_m4_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	pruss_ocp_gclk: pruss_ocp_gclk@4248 {
+	pruss_ocp_gclk: clock-pruss-ocp-gclk@4248 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "pruss_ocp_gclk";
 		clocks = <&sysclk_div>, <&dpll_disp_m2_ck>;
 		reg = <0x4248>;
 	};
 
-	clk_32k_tpm_ck: clk_32k_tpm_ck {
+	clk_32k_tpm_ck: clock-clk-32k-tpm {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "clk_32k_tpm_ck";
 		clock-frequency = <32768>;
 	};
 
-	timer1_fck: timer1_fck@4200 {
+	timer1_fck: clock-timer1-fck@4200 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "timer1_fck";
 		clocks = <&sys_clkin_ck>, <&clkdiv32k_ick>, <&tclkin_ck>, <&clk_rc32k_ck>, <&clk_32768_ck>, <&clk_32k_tpm_ck>;
 		reg = <0x4200>;
 	};
 
-	timer2_fck: timer2_fck@4204 {
+	timer2_fck: clock-timer2-fck@4204 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "timer2_fck";
 		clocks = <&tclkin_ck>, <&sys_clkin_ck>, <&clkdiv32k_ick>;
 		reg = <0x4204>;
 	};
 
-	timer3_fck: timer3_fck@4208 {
+	timer3_fck: clock-timer3-fck@4208 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "timer3_fck";
 		clocks = <&tclkin_ck>, <&sys_clkin_ck>, <&clkdiv32k_ick>;
 		reg = <0x4208>;
 	};
 
-	timer4_fck: timer4_fck@420c {
+	timer4_fck: clock-timer4-fck@420c {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "timer4_fck";
 		clocks = <&tclkin_ck>, <&sys_clkin_ck>, <&clkdiv32k_ick>;
 		reg = <0x420c>;
 	};
 
-	timer5_fck: timer5_fck@4210 {
+	timer5_fck: clock-timer5-fck@4210 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "timer5_fck";
 		clocks = <&tclkin_ck>, <&sys_clkin_ck>, <&clkdiv32k_ick>;
 		reg = <0x4210>;
 	};
 
-	timer6_fck: timer6_fck@4214 {
+	timer6_fck: clock-timer6-fck@4214 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "timer6_fck";
 		clocks = <&tclkin_ck>, <&sys_clkin_ck>, <&clkdiv32k_ick>;
 		reg = <0x4214>;
 	};
 
-	timer7_fck: timer7_fck@4218 {
+	timer7_fck: clock-timer7-fck@4218 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "timer7_fck";
 		clocks = <&tclkin_ck>, <&sys_clkin_ck>, <&clkdiv32k_ick>;
 		reg = <0x4218>;
 	};
 
-	wdt1_fck: wdt1_fck@422c {
+	wdt1_fck: clock-wdt1-fck@422c {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "wdt1_fck";
 		clocks = <&clk_rc32k_ck>, <&clkdiv32k_ick>;
 		reg = <0x422c>;
 	};
 
-	l3_gclk: l3_gclk {
+	adc_mag_fck: adc_mag_fck@424c {
+		#clock-cells = <0>;
+		compatible = "ti,mux-clock";
+		clocks = <&sys_clkin_ck>, <&dpll_per_m2_ck>;
+		reg = <0x424c>;
+	};
+
+	l3_gclk: clock-l3-gclk {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "l3_gclk";
 		clocks = <&dpll_core_m4_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	dpll_core_m4_div2_ck: dpll_core_m4_div2_ck {
+	dpll_core_m4_div2_ck: clock-dpll-core-m4-div2 {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "dpll_core_m4_div2_ck";
 		clocks = <&sysclk_div>;
 		clock-mult = <1>;
 		clock-div = <2>;
 	};
 
-	l4hs_gclk: l4hs_gclk {
+	l4hs_gclk: clock-l4hs-gclk {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "l4hs_gclk";
 		clocks = <&dpll_core_m4_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	l3s_gclk: l3s_gclk {
+	l3s_gclk: clock-l3s-gclk {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "l3s_gclk";
 		clocks = <&dpll_core_m4_div2_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	l4ls_gclk: l4ls_gclk {
+	l4ls_gclk: clock-l4ls-gclk {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "l4ls_gclk";
 		clocks = <&dpll_core_m4_div2_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	cpsw_125mhz_gclk: cpsw_125mhz_gclk {
+	cpsw_125mhz_gclk: clock-cpsw-125mhz-gclk {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "cpsw_125mhz_gclk";
 		clocks = <&dpll_core_m5_ck>;
 		clock-mult = <1>;
 		clock-div = <2>;
 	};
 
-	cpsw_cpts_rft_clk: cpsw_cpts_rft_clk@4238 {
+	cpsw_cpts_rft_clk: clock-cpsw-cpts-rft@4238 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "cpsw_cpts_rft_clk";
 		clocks = <&sysclk_div>, <&dpll_core_m5_ck>, <&dpll_disp_m2_ck>;
 		reg = <0x4238>;
 	};
 
-	dpll_clksel_mac_clk: dpll_clksel_mac_clk@4234 {
+	dpll_clksel_mac_clk: clock-dpll-clksel-mac-2@4234 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_clksel_mac_clk";
 		clocks = <&dpll_core_m5_ck>;
 		reg = <0x4234>;
 		ti,bit-shift = <2>;
 		ti,dividers = <2>, <5>;
 	};
 
-	clk_32k_mosc_ck: clk_32k_mosc_ck {
+	clk_32k_mosc_ck: clock-clk-32k-mosc {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "clk_32k_mosc_ck";
 		clock-frequency = <32768>;
 	};
 
-	gpio0_dbclk_mux_ck: gpio0_dbclk_mux_ck@4240 {
+	gpio0_dbclk_mux_ck: clock-gpio0-dbclk-mux@4240 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "gpio0_dbclk_mux_ck";
 		clocks = <&clk_rc32k_ck>, <&clk_32768_ck>, <&clkdiv32k_ick>, <&clk_32k_mosc_ck>, <&clk_32k_tpm_ck>;
 		reg = <0x4240>;
 	};
 
-	mmc_clk: mmc_clk {
+	mmc_clk: clock-mmc {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "mmc_clk";
 		clocks = <&dpll_per_m2_ck>;
 		clock-mult = <1>;
 		clock-div = <2>;
 	};
 
-	gfx_fclk_clksel_ck: gfx_fclk_clksel_ck@423c {
+	gfx_fclk_clksel_ck: clock-gfx-fclk-clksel-1@423c {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "gfx_fclk_clksel_ck";
 		clocks = <&sysclk_div>, <&dpll_per_m2_ck>;
 		ti,bit-shift = <1>;
 		reg = <0x423c>;
 	};
 
-	gfx_fck_div_ck: gfx_fck_div_ck@423c {
+	gfx_fck_div_ck: clock-gfx-fck-div@423c {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "gfx_fck_div_ck";
 		clocks = <&gfx_fclk_clksel_ck>;
 		reg = <0x423c>;
 		ti,max-div = <2>;
 	};
 
-	disp_clk: disp_clk@4244 {
+	disp_clk: clock-disp@4244 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "disp_clk";
 		clocks = <&dpll_disp_m2_ck>, <&dpll_core_m5_ck>, <&dpll_per_m2_ck>;
 		reg = <0x4244>;
 		ti,set-rate-parent;
 	};
 
-	dpll_extdev_ck: dpll_extdev_ck@2e60 {
+	dpll_extdev_ck: clock@2e60 {
 		#clock-cells = <0>;
 		compatible = "ti,am3-dpll-clock";
+		clock-output-names = "dpll_extdev_ck";
 		clocks = <&sys_clkin_ck>, <&sys_clkin_ck>;
 		reg = <0x2e60>, <0x2e64>, <0x2e6c>, <0x2e88>, <0x2e8c>;
 	};
 
-	dpll_extdev_m2_ck: dpll_extdev_m2_ck@2e70 {
+	dpll_extdev_m2_ck: clock-dpll-extdev-m2-8@2e70 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_extdev_m2_ck";
 		clocks = <&dpll_extdev_ck>;
 		ti,max-div = <127>;
 		ti,autoidle-shift = <8>;
@@ -571,66 +650,75 @@
 		ti,invert-autoidle-bit;
 	};
 
-	mux_synctimer32k_ck: mux_synctimer32k_ck@4230 {
+	mux_synctimer32k_ck: clock-mux-synctimer32k@4230 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "mux_synctimer32k_ck";
 		clocks = <&clk_32768_ck>, <&clk_32k_tpm_ck>, <&clkdiv32k_ick>;
 		reg = <0x4230>;
 	};
 
-	timer8_fck: timer8_fck@421c {
+	timer8_fck: clock-timer8-fck@421c {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "timer8_fck";
 		clocks = <&tclkin_ck>, <&sys_clkin_ck>, <&clkdiv32k_ick>, <&clk_32k_tpm_ck>;
 		reg = <0x421c>;
 	};
 
-	timer9_fck: timer9_fck@4220 {
+	timer9_fck: clock-timer9-fck@4220 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "timer9_fck";
 		clocks = <&tclkin_ck>, <&sys_clkin_ck>, <&clkdiv32k_ick>, <&clk_32k_tpm_ck>;
 		reg = <0x4220>;
 	};
 
-	timer10_fck: timer10_fck@4224 {
+	timer10_fck: clock-timer10-fck@4224 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "timer10_fck";
 		clocks = <&tclkin_ck>, <&sys_clkin_ck>, <&clkdiv32k_ick>, <&clk_32k_tpm_ck>;
 		reg = <0x4224>;
 	};
 
-	timer11_fck: timer11_fck@4228 {
+	timer11_fck: clock-timer11-fck@4228 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "timer11_fck";
 		clocks = <&tclkin_ck>, <&sys_clkin_ck>, <&clkdiv32k_ick>, <&clk_32k_tpm_ck>;
 		reg = <0x4228>;
 	};
 
-	cpsw_50m_clkdiv: cpsw_50m_clkdiv {
+	cpsw_50m_clkdiv: clock-cpsw-50m-clkdiv {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "cpsw_50m_clkdiv";
 		clocks = <&dpll_core_m5_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	cpsw_5m_clkdiv: cpsw_5m_clkdiv {
+	cpsw_5m_clkdiv: clock-cpsw-5m-clkdiv {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "cpsw_5m_clkdiv";
 		clocks = <&cpsw_50m_clkdiv>;
 		clock-mult = <1>;
 		clock-div = <10>;
 	};
 
-	dpll_ddr_x2_ck: dpll_ddr_x2_ck {
+	dpll_ddr_x2_ck: clock-dpll-ddr-x2 {
 		#clock-cells = <0>;
 		compatible = "ti,am3-dpll-x2-clock";
+		clock-output-names = "dpll_ddr_x2_ck";
 		clocks = <&dpll_ddr_ck>;
 	};
 
-	dpll_ddr_m4_ck: dpll_ddr_m4_ck@2db8 {
+	dpll_ddr_m4_ck: clock-dpll-ddr-m4-8@2db8 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_ddr_m4_ck";
 		clocks = <&dpll_ddr_x2_ck>;
 		ti,max-div = <31>;
 		ti,autoidle-shift = <8>;
@@ -639,9 +727,10 @@
 		ti,invert-autoidle-bit;
 	};
 
-	dpll_per_clkdcoldo: dpll_per_clkdcoldo@2e14 {
+	dpll_per_clkdcoldo: clock-dpll-per-clkdcoldo-8@2e14 {
 		#clock-cells = <0>;
 		compatible = "ti,fixed-factor-clock";
+		clock-output-names = "dpll_per_clkdcoldo";
 		clocks = <&dpll_per_ck>;
 		ti,clock-mult = <1>;
 		ti,clock-div = <1>;
@@ -650,91 +739,102 @@
 		ti,invert-autoidle-bit;
 	};
 
-	dll_aging_clk_div: dll_aging_clk_div@4250 {
+	dll_aging_clk_div: clock-dll-aging-clk-div@4250 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dll_aging_clk_div";
 		clocks = <&sys_clkin_ck>;
 		reg = <0x4250>;
 		ti,dividers = <8>, <16>, <32>;
 	};
 
-	div_core_25m_ck: div_core_25m_ck {
+	div_core_25m_ck: clock-div-core-25m {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "div_core_25m_ck";
 		clocks = <&sysclk_div>;
 		clock-mult = <1>;
 		clock-div = <8>;
 	};
 
-	func_12m_clk: func_12m_clk {
+	func_12m_clk: clock-func-12m {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "func_12m_clk";
 		clocks = <&dpll_per_m2_ck>;
 		clock-mult = <1>;
 		clock-div = <16>;
 	};
 
-	vtp_clk_div: vtp_clk_div {
+	vtp_clk_div: clock-vtp-clk-div {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "vtp_clk_div";
 		clocks = <&sys_clkin_ck>;
 		clock-mult = <1>;
 		clock-div = <2>;
 	};
 
-	usbphy_32khz_clkmux: usbphy_32khz_clkmux@4260 {
+	usbphy_32khz_clkmux: clock-usbphy-32khz-clkmux@4260 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "usbphy_32khz_clkmux";
 		clocks = <&clk_32768_ck>, <&clk_32k_tpm_ck>;
 		reg = <0x4260>;
 	};
 
-	usb_phy0_always_on_clk32k: usb_phy0_always_on_clk32k@2a40 {
+	usb_phy0_always_on_clk32k: clock-usb-phy0-always-on-clk32k-8@2a40 {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
+		clock-output-names = "usb_phy0_always_on_clk32k";
 		clocks = <&usbphy_32khz_clkmux>;
 		ti,bit-shift = <8>;
 		reg = <0x2a40>;
 	};
 
-	usb_phy1_always_on_clk32k: usb_phy1_always_on_clk32k@2a48 {
+	usb_phy1_always_on_clk32k: clock-usb-phy1-always-on-clk32k-8@2a48 {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
+		clock-output-names = "usb_phy1_always_on_clk32k";
 		clocks = <&usbphy_32khz_clkmux>;
 		ti,bit-shift = <8>;
 		reg = <0x2a48>;
 	};
 
-	clkout1_osc_div_ck: clkout1-osc-div-ck {
+	clkout1_osc_div_ck: clock-clkout1-osc-div-ck {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "clkout1_osc_div_ck";
 		clocks = <&sys_clkin_ck>;
 		ti,bit-shift = <20>;
 		ti,max-div = <4>;
 		reg = <0x4100>;
 	};
 
-	clkout1_src2_mux_ck: clkout1-src2-mux-ck {
+	clkout1_src2_mux_ck: clock-clkout1-src2-mux-ck {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "clkout1_src2_mux_ck";
 		clocks = <&clk_rc32k_ck>, <&sysclk_div>, <&dpll_ddr_m2_ck>,
 			 <&dpll_per_m2_ck>, <&dpll_disp_m2_ck>,
 			 <&dpll_mpu_m2_ck>;
 		reg = <0x4100>;
 	};
 
-	clkout1_src2_pre_div_ck: clkout1-src2-pre-div-ck {
+	clkout1_src2_pre_div_ck: clock-clkout1-src2-pre-div-ck {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "clkout1_src2_pre_div_ck";
 		clocks = <&clkout1_src2_mux_ck>;
 		ti,bit-shift = <4>;
 		ti,max-div = <8>;
 		reg = <0x4100>;
 	};
 
-	clkout1_src2_post_div_ck: clkout1-src2-post-div-ck {
+	clkout1_src2_post_div_ck: clock-clkout1-src2-post-div-ck {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "clkout1_src2_post_div_ck";
 		clocks = <&clkout1_src2_pre_div_ck>;
 		ti,bit-shift = <8>;
 		ti,max-div = <32>;
@@ -742,18 +842,20 @@
 		reg = <0x4100>;
 	};
 
-	clkout1_mux_ck: clkout1-mux-ck {
+	clkout1_mux_ck: clock-clkout1-mux-ck {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "clkout1_mux_ck";
 		clocks = <&clkout1_osc_div_ck>, <&clk_rc32k_ck>,
 			 <&clkout1_src2_post_div_ck>, <&dpll_extdev_m2_ck>;
 		ti,bit-shift = <16>;
 		reg = <0x4100>;
 	};
 
-	clkout1_ck: clkout1-ck {
+	clkout1_ck: clock-clkout1-ck {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
+		clock-output-names = "clkout1_ck";
 		clocks = <&clkout1_mux_ck>;
 		ti,bit-shift = <23>;
 		reg = <0x4100>;
@@ -761,120 +863,138 @@
 };
 
 &prcm {
-	wkup_cm: wkup-cm@2800 {
+	wkup_cm: clock@2800 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "wkup_cm";
 		reg = <0x2800 0x400>;
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0 0x2800 0x400>;
 
-		l3s_tsc_clkctrl: l3s-tsc-clkctrl@120 {
+		l3s_tsc_clkctrl: clock@120 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "l3s_tsc_clkctrl";
 			reg = <0x120 0x4>;
 			#clock-cells = <2>;
 		};
 
-		l4_wkup_aon_clkctrl: l4-wkup-aon-clkctrl@228 {
+		l4_wkup_aon_clkctrl: clock@228 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "l4_wkup_aon_clkctrl";
 			reg = <0x228 0xc>;
 			#clock-cells = <2>;
 		};
 
-		l4_wkup_clkctrl: l4-wkup-clkctrl@220 {
+		l4_wkup_clkctrl: clock@220 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "l4_wkup_clkctrl";
 			reg = <0x220 0x4>, <0x328 0x44>;
 			#clock-cells = <2>;
 		};
 
 	};
 
-	mpu_cm: mpu-cm@8300 {
+	mpu_cm: clock@8300 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "mpu_cm";
 		reg = <0x8300 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0 0x8300 0x100>;
 
-		mpu_clkctrl: mpu-clkctrl@20 {
+		mpu_clkctrl: clock@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "mpu_clkctrl";
 			reg = <0x20 0x4>;
 			#clock-cells = <2>;
 		};
 	};
 
-	gfx_l3_cm: gfx-l3-cm@8400 {
+	gfx_l3_cm: clock@8400 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "gfx_l3_cm";
 		reg = <0x8400 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0 0x8400 0x100>;
 
-		gfx_l3_clkctrl: gfx-l3-clkctrl@20 {
+		gfx_l3_clkctrl: clock@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "gfx_l3_clkctrl";
 			reg = <0x20 0x4>;
 			#clock-cells = <2>;
 		};
 	};
 
-	l4_rtc_cm: l4-rtc-cm@8500 {
+	l4_rtc_cm: clock@8500 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "l4_rtc_cm";
 		reg = <0x8500 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0 0x8500 0x100>;
 
-		l4_rtc_clkctrl: l4-rtc-clkctrl@20 {
+		l4_rtc_clkctrl: clock@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "l4_rtc_clkctrl";
 			reg = <0x20 0x4>;
 			#clock-cells = <2>;
 		};
 	};
 
-	per_cm: per-cm@8800 {
+	per_cm: clock@8800 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "per_cm";
 		reg = <0x8800 0xc00>;
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0 0x8800 0xc00>;
 
-		l3_clkctrl: l3-clkctrl@20 {
+		l3_clkctrl: clock@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "l3_clkctrl";
 			reg = <0x20 0x3c>, <0x78 0x2c>;
 			#clock-cells = <2>;
 		};
 
-		l3s_clkctrl: l3s-clkctrl@68 {
+		l3s_clkctrl: clock@68 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "l3s_clkctrl";
 			reg = <0x68 0xc>, <0x220 0x4c>;
 			#clock-cells = <2>;
 		};
 
-		pruss_ocp_clkctrl: pruss-ocp-clkctrl@320 {
+		pruss_ocp_clkctrl: clock@320 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "pruss_ocp_clkctrl";
 			reg = <0x320 0x4>;
 			#clock-cells = <2>;
 		};
 
-		l4ls_clkctrl: l4ls-clkctrl@420 {
+		l4ls_clkctrl: clock@420 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "l4ls_clkctrl";
 			reg = <0x420 0x1a4>;
 			#clock-cells = <2>;
 		};
 
-		emif_clkctrl: emif-clkctrl@720 {
+		emif_clkctrl: clock@720 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "emif_clkctrl";
 			reg = <0x720 0x4>;
 			#clock-cells = <2>;
 		};
 
-		dss_clkctrl: dss-clkctrl@a20 {
+		dss_clkctrl: clock@a20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "dss_clkctrl";
 			reg = <0xa20 0x4>;
 			#clock-cells = <2>;
 		};
 
-		cpsw_125mhz_clkctrl: cpsw-125mhz-clkctrl@b20 {
+		cpsw_125mhz_clkctrl: clock@b20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "cpsw_125mhz_clkctrl";
 			reg = <0xb20 0x4>;
 			#clock-cells = <2>;
 		};
diff --git a/arch/arm/boot/dts/am5748.dtsi b/arch/arm/boot/dts/am5748.dtsi
index c260aa1a85bd..a1f029e9d1f3 100644
--- a/arch/arm/boot/dts/am5748.dtsi
+++ b/arch/arm/boot/dts/am5748.dtsi
@@ -25,6 +25,10 @@
 	status = "disabled";
 };
 
+&usb4_tm {
+	status = "disabled";
+};
+
 &atl_tm {
 	status = "disabled";
 };
diff --git a/arch/arm/boot/dts/am574x-idk.dts b/arch/arm/boot/dts/am574x-idk.dts
index 6dff3660bf09..47b9174d2353 100644
--- a/arch/arm/boot/dts/am574x-idk.dts
+++ b/arch/arm/boot/dts/am574x-idk.dts
@@ -18,7 +18,7 @@
 
 &qspi {
 	spi-max-frequency = <96000000>;
-	m25p80@0 {
+	flash@0 {
 		spi-max-frequency = <96000000>;
 	};
 };
diff --git a/arch/arm/boot/dts/am57xx-cl-som-am57x.dts b/arch/arm/boot/dts/am57xx-cl-som-am57x.dts
index 2e94f32d9dfc..2fc9a5d5e0c0 100644
--- a/arch/arm/boot/dts/am57xx-cl-som-am57x.dts
+++ b/arch/arm/boot/dts/am57xx-cl-som-am57x.dts
@@ -491,7 +491,7 @@
 
 	spi-max-frequency = <48000000>;
 
-	spi_flash: spi_flash@0 {
+	spi_flash: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "spansion,m25p80", "jedec,spi-nor";
diff --git a/arch/arm/boot/dts/am57xx-idk-common.dtsi b/arch/arm/boot/dts/am57xx-idk-common.dtsi
index 9fcb8944aa3e..c06eda817242 100644
--- a/arch/arm/boot/dts/am57xx-idk-common.dtsi
+++ b/arch/arm/boot/dts/am57xx-idk-common.dtsi
@@ -526,7 +526,7 @@
 	status = "okay";
 
 	spi-max-frequency = <76800000>;
-	m25p80@0 {
+	flash@0 {
 		compatible = "s25fl256s1", "jedec,spi-nor";
 		spi-max-frequency = <76800000>;
 		reg = <0>;
diff --git a/arch/arm/boot/dts/animeo_ip.dts b/arch/arm/boot/dts/animeo_ip.dts
index 7da718abbd85..29936bfbeeb7 100644
--- a/arch/arm/boot/dts/animeo_ip.dts
+++ b/arch/arm/boot/dts/animeo_ip.dts
@@ -168,26 +168,24 @@
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 
-		keyswitch_in {
+		key-switch-in {
 			label = "keyswitch_in";
 			gpios = <&pioB 1 GPIO_ACTIVE_HIGH>;
 			linux,code = <28>;
 			wakeup-source;
 		};
 
-		error_in {
+		key-error-in {
 			label = "error_in";
 			gpios = <&pioB 2 GPIO_ACTIVE_HIGH>;
 			linux,code = <29>;
 			wakeup-source;
 		};
 
-		btn {
+		key-s {
 			label = "btn";
 			gpios = <&pioC 23 GPIO_ACTIVE_HIGH>;
 			linux,code = <31>;
diff --git a/arch/arm/boot/dts/arm-realview-eb.dtsi b/arch/arm/boot/dts/arm-realview-eb.dtsi
index 2dfb32bf9d48..fbb2258b451f 100644
--- a/arch/arm/boot/dts/arm-realview-eb.dtsi
+++ b/arch/arm/boot/dts/arm-realview-eb.dtsi
@@ -399,7 +399,7 @@
 			compatible = "arm,pl022", "arm,primecell";
 			reg = <0x1000d000 0x1000>;
 			clocks = <&sspclk>, <&pclk>;
-			clock-names = "SSPCLK", "apb_pclk";
+			clock-names = "sspclk", "apb_pclk";
 		};
 
 		wdog: watchdog@10010000 {
diff --git a/arch/arm/boot/dts/arm-realview-pb1176.dts b/arch/arm/boot/dts/arm-realview-pb1176.dts
index 06b8723b09eb..efed325af88d 100644
--- a/arch/arm/boot/dts/arm-realview-pb1176.dts
+++ b/arch/arm/boot/dts/arm-realview-pb1176.dts
@@ -410,7 +410,7 @@
 			interrupt-parent = <&intc_dc1176>;
 			interrupts = <0 17 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&sspclk>, <&pclk>;
-			clock-names = "SSPCLK", "apb_pclk";
+			clock-names = "sspclk", "apb_pclk";
 		};
 
 		pb1176_serial0: serial@1010c000 {
diff --git a/arch/arm/boot/dts/arm-realview-pb11mp.dts b/arch/arm/boot/dts/arm-realview-pb11mp.dts
index 295aef448123..89103d54ecc1 100644
--- a/arch/arm/boot/dts/arm-realview-pb11mp.dts
+++ b/arch/arm/boot/dts/arm-realview-pb11mp.dts
@@ -555,7 +555,7 @@
 			interrupt-parent = <&intc_pb11mp>;
 			interrupts = <0 11 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&sspclk>, <&pclk>;
-			clock-names = "SSPCLK", "apb_pclk";
+			clock-names = "sspclk", "apb_pclk";
 		};
 
 		watchdog@1000f000 {
diff --git a/arch/arm/boot/dts/arm-realview-pbx.dtsi b/arch/arm/boot/dts/arm-realview-pbx.dtsi
index 6f61f968d689..ec1507c5147c 100644
--- a/arch/arm/boot/dts/arm-realview-pbx.dtsi
+++ b/arch/arm/boot/dts/arm-realview-pbx.dtsi
@@ -390,7 +390,7 @@
 			compatible = "arm,pl022", "arm,primecell";
 			reg = <0x1000d000 0x1000>;
 			clocks = <&sspclk>, <&pclk>;
-			clock-names = "SSPCLK", "apb_pclk";
+			clock-names = "sspclk", "apb_pclk";
 		};
 
 		wdog0: watchdog@1000f000 {
diff --git a/arch/arm/boot/dts/armada-370-c200-v2.dts b/arch/arm/boot/dts/armada-370-c200-v2.dts
new file mode 100644
index 000000000000..84d40e1d70ef
--- /dev/null
+++ b/arch/arm/boot/dts/armada-370-c200-v2.dts
@@ -0,0 +1,388 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Device Tree file for Ctera C200-V2
+ *
+ * Copyright (C) 2022 Pawel Dembicki <paweldembicki@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "armada-370.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/thermal/thermal.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+	model = "Ctera C200 V2";
+	compatible = "ctera,c200-v2", "marvell,armada370", "marvell,armada-370-xp";
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x40000000>; /* 1024 MB */
+	};
+
+	soc {
+		ranges = <MBUS_ID(0xf0, 0x01) 0 0xd0000000 0x100000
+			  MBUS_ID(0x01, 0xe0) 0 0xfff00000 0x100000
+			  MBUS_ID(0x09, 0x01) 0 0xf1100000 0x10000>;
+	};
+
+	thermal-zones {
+		ethphy-thermal {
+			polling-delay = <20000>;
+			polling-delay-passive = <2000>;
+
+			thermal-sensors = <&ethphy0>;
+
+			trips {
+				ethphy_alert1: trip1 {
+					temperature = <65000>;
+					hysteresis = <4000>;
+					type = "passive";
+				};
+
+				ethphy_crit: trip2 {
+					temperature = <100000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+	};
+
+	beeper {
+		compatible = "pwm-beeper";
+		pinctrl-0 = <&pmx_beeper>;
+		pinctrl-names = "default";
+		pwms = <&gpio1 31 4000>;
+	};
+
+	gpio-poweroff {
+		compatible = "gpio-poweroff";
+		pinctrl-0 = <&pmx_poweroff>;
+		pinctrl-names = "default";
+		gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>;
+	};
+
+	keys {
+		compatible = "gpio-keys";
+		pinctrl-0 = <&pmx_buttons>;
+		pinctrl-names = "default";
+
+		button-power {
+			label = "Power Button";
+			linux,code = <KEY_POWER>;
+			gpios = <&gpio0 10 GPIO_ACTIVE_HIGH>;
+		};
+
+		button-reset {
+			label = "Reset Button";
+			linux,code = <KEY_RESTART>;
+			gpios = <&gpio0 6 GPIO_ACTIVE_LOW>;
+		};
+
+		button-usb1 {
+			label = "USB1 Button";
+			linux,code = <BTN_0>;
+			gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
+		};
+
+		button-usb2 {
+			label = "USB2 Button";
+			linux,code = <BTN_1>;
+			gpios = <&gpio0 14 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-0 = <&pmx_leds1 &pmx_leds2>;
+		pinctrl-names = "default";
+
+		led-0 {
+			function = LED_FUNCTION_USB;
+			function-enumerator = <2>;
+			color = <LED_COLOR_ID_RED>;
+			gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
+		};
+
+		led-1 {
+			function = LED_FUNCTION_USB;
+			function-enumerator = <2>;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
+		};
+
+		led-2 {
+			function = LED_FUNCTION_USB;
+			function-enumerator = <1>;
+			color = <LED_COLOR_ID_RED>;
+			gpios = <&gpio0 15 GPIO_ACTIVE_LOW>;
+		};
+
+		led-3 {
+			function = LED_FUNCTION_USB;
+			function-enumerator = <1>;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&gpio0 16 GPIO_ACTIVE_LOW>;
+		};
+
+		led-4 {
+			function = LED_FUNCTION_DISK;
+			function-enumerator = <2>;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
+		};
+
+		led-5 {
+			function = LED_FUNCTION_DISK;
+			function-enumerator = <1>;
+			color = <LED_COLOR_ID_RED>;
+			gpios = <&gpio1 18 GPIO_ACTIVE_LOW>;
+		};
+
+		led-6 {
+			function = LED_FUNCTION_DISK;
+			function-enumerator = <2>;
+			color = <LED_COLOR_ID_RED>;
+			gpios = <&gpio1 19 GPIO_ACTIVE_LOW>;
+		};
+
+		led-7 {
+			function = LED_FUNCTION_INDICATOR;
+			color = <LED_COLOR_ID_BLUE>;
+			gpios = <&gpio1 20 GPIO_ACTIVE_HIGH>;
+		};
+
+		led-8 {
+			function = LED_FUNCTION_DISK_ERR;
+			color = <LED_COLOR_ID_RED>;
+			gpios = <&gpio1 21 GPIO_ACTIVE_LOW>;
+		};
+
+		led-9 {
+			function = LED_FUNCTION_DISK_ERR;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&gpio1 23 GPIO_ACTIVE_LOW>;
+		};
+
+		led-10 {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_RED>;
+			gpios = <&gpio1 24 GPIO_ACTIVE_LOW>;
+		};
+
+		led-11 {
+			function = LED_FUNCTION_DISK;
+			function-enumerator = <1>;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
+		};
+
+		led-12 {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&gpio1 26 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&coherencyfab {
+	broken-idle;
+};
+
+&eth1 {
+	pinctrl-0 = <&ge1_rgmii_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+	phy-handle = <&ethphy0>;
+	phy-connection-type = "rgmii-id";
+};
+
+&i2c0 {
+	pinctrl-0 = <&i2c0_pins>;
+	pinctrl-names = "default";
+	clock-frequency = <100000>;
+	status = "okay";
+
+	hwmon@2a {
+		compatible = "nuvoton,nct7802";
+		reg = <0x2a>;
+	};
+
+	rtc@30 {
+		compatible = "sii,s35390a";
+		reg = <0x30>;
+	};
+};
+
+&mdio {
+	pinctrl-0 = <&mdio_pins>;
+	pinctrl-names = "default";
+
+	ethphy0: ethernet-phy@0 { /* Marvell 88E1318 */
+		reg = <0>;
+		#thermal-sensor-cells = <0>;
+	};
+};
+
+&nand_controller {
+	status = "okay";
+
+	nand@0 {
+		reg = <0>;
+		label = "pxa3xx_nand-0";
+		nand-rb = <0>;
+		marvell,nand-keep-config;
+		nand-on-flash-bbt;
+		nand-ecc-strength = <4>;
+		nand-ecc-step-size = <512>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "uboot";
+				reg = <0x0000000 0x200000>;
+				read-only;
+			};
+
+			partition@200000 {
+				label = "certificate";
+				reg = <0x0200000 0x100000>;
+				read-only;
+			};
+
+			partition@300000 {
+				label = "preset_cfg";
+				reg = <0x0300000 0x100000>;
+				read-only;
+			};
+
+			partition@400000 {
+				label = "dev_params";
+				reg = <0x0400000 0x100000>;
+				read-only;
+			};
+			partition@500000 {
+				label = "active_bank";
+				reg = <0x0500000 0x0100000>;
+			};
+
+			partition@600000 {
+				label = "magic";
+				reg = <0x0600000 0x0100000>;
+				read-only;
+			};
+
+			partition@700000 {
+				label = "bank1";
+				reg = <0x0700000 0x2800000>;
+			};
+
+			partition@2f00000 {
+				label = "bank2";
+				reg = <0x2f00000 0x2800000>;
+			};
+
+			/* 0x5700000-0x5a00000 undefined in vendor firmware */
+
+			partition@5a00000 {
+				label = "reserved";
+				reg = <0x5a00000 0x2000000>;
+			};
+
+			partition@7a00000 {
+				label = "rootfs";
+				reg = <0x7a00000 0x8600000>;
+			};
+		};
+	};
+};
+
+&pciec {
+	status = "okay";
+
+	pcie@1,0 { /* Renesas uPD720202 USB 3.0 controller */
+		pinctrl-0 = <&pmx_pcie>;
+		pinctrl-names = "default";
+		status = "okay";
+		reset-gpios = <&gpio1 27 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&pinctrl {
+	pmx_poweroff: pmx-poweroff {
+		marvell,pins = "mpp7";
+		marvell,function = "gpo";
+	};
+
+	pmx_power_cpu: pmx-power-cpu {
+		marvell,pins = "mpp4";
+		marvell,function = "vdd";
+	};
+
+	pmx_buttons: pmx-buttons {
+		marvell,pins = "mpp6", "mpp10", "mpp14", "mpp32";
+		marvell,function = "gpio";
+	};
+
+	pmx_leds1: pmx-leds1 {
+		marvell,pins = "mpp47";
+		marvell,function = "gpo";
+	};
+
+	pmx_leds2: pmx-leds2 {
+		marvell,pins = "mpp12", "mpp13", "mpp15", "mpp16", "mpp50", "mpp51",
+			       "mpp52", "mpp53", "mpp55", "mpp56", "mpp57", "mpp58";
+		marvell,function = "gpio";
+	};
+
+	pmx_pcie: pmx-pcie {
+		marvell,pins = "mpp59";
+		marvell,function = "gpio";
+	};
+
+	pmx_beeper: pmx-beeper {
+		marvell,pins = "mpp63";
+		marvell,function = "gpio";
+	};
+};
+
+&pmsu {
+	pinctrl-0 = <&pmx_power_cpu>;
+	pinctrl-names = "default";
+};
+
+&rtc {
+	status = "disabled";
+};
+
+&sata {
+	nr-ports = <2>;
+	status = "okay";
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	hdd0_temp: sata-port@0 {
+		reg = <0>;
+		#thermal-sensor-cells = <0>;
+	};
+
+	hdd1_temp: sata-port@1 {
+		reg = <1>;
+		#thermal-sensor-cells = <0>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/armada-370-db.dts b/arch/arm/boot/dts/armada-370-db.dts
index 77261a2fb949..a7dc4c04d10b 100644
--- a/arch/arm/boot/dts/armada-370-db.dts
+++ b/arch/arm/boot/dts/armada-370-db.dts
@@ -203,7 +203,7 @@
 	pinctrl-names = "default";
 	status = "okay";
 
-	spi-flash@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "mx25l25635e", "jedec,spi-nor";
diff --git a/arch/arm/boot/dts/armada-370-rd.dts b/arch/arm/boot/dts/armada-370-rd.dts
index c910d157a686..6ba7699b69ed 100644
--- a/arch/arm/boot/dts/armada-370-rd.dts
+++ b/arch/arm/boot/dts/armada-370-rd.dts
@@ -84,8 +84,6 @@
 
 			gpio-keys {
 				compatible = "gpio-keys";
-				#address-cells = <1>;
-				#size-cells = <0>;
 				button {
 					label = "Software Button";
 					linux,code = <KEY_POWER>;
diff --git a/arch/arm/boot/dts/armada-370-seagate-nas-xbay.dtsi b/arch/arm/boot/dts/armada-370-seagate-nas-xbay.dtsi
index b52634ecf1d9..866b8630d407 100644
--- a/arch/arm/boot/dts/armada-370-seagate-nas-xbay.dtsi
+++ b/arch/arm/boot/dts/armada-370-seagate-nas-xbay.dtsi
@@ -108,22 +108,20 @@
 
 	gpio-keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 
-		power {
+		button-power {
 			label = "Power button";
 			linux,code = <KEY_POWER>;
 			gpios = <&gpio1 19 GPIO_ACTIVE_LOW>;
 			debounce-interval = <100>;
 		};
-		backup {
+		button-backup {
 			label = "Backup button";
 			linux,code = <KEY_OPTION>;
 			gpios = <&gpio0 31 GPIO_ACTIVE_LOW>;
 			debounce-interval = <100>;
 		};
-		reset {
+		button-reset {
 			label = "Reset Button";
 			linux,code = <KEY_RESTART>;
 			gpios = <&gpio1 23 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/armada-370-seagate-personal-cloud.dtsi b/arch/arm/boot/dts/armada-370-seagate-personal-cloud.dtsi
index a624b2371fb6..702a85af2078 100644
--- a/arch/arm/boot/dts/armada-370-seagate-personal-cloud.dtsi
+++ b/arch/arm/boot/dts/armada-370-seagate-personal-cloud.dtsi
@@ -83,22 +83,20 @@
 
 	gpio-keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 
-		power {
+		button-power {
 			label = "Power button";
 			linux,code = <KEY_POWER>;
 			gpios = <&gpio1 19 GPIO_ACTIVE_HIGH>;
 			debounce-interval = <100>;
 		};
-		reset {
+		button-reset {
 			label = "Reset Button";
 			linux,code = <KEY_RESTART>;
 			gpios = <&gpio1 23 GPIO_ACTIVE_LOW>;
 			debounce-interval = <100>;
 		};
-		button {
+		button-usb {
 			label = "USB VBUS error";
 			linux,code = <KEY_UNKNOWN>;
 			gpios = <&gpio1 21 GPIO_ACTIVE_LOW>;
@@ -159,7 +157,7 @@
 	pinctrl-0 = <&spi0_pins2>;
 	pinctrl-names = "default";
 
-	spi-flash@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		/* MX25L8006E */
diff --git a/arch/arm/boot/dts/armada-370-synology-ds213j.dts b/arch/arm/boot/dts/armada-370-synology-ds213j.dts
index 64f2ce254fb6..e72b8ed4b997 100644
--- a/arch/arm/boot/dts/armada-370-synology-ds213j.dts
+++ b/arch/arm/boot/dts/armada-370-synology-ds213j.dts
@@ -258,7 +258,7 @@
 &spi0 {
 	status = "okay";
 
-	spi-flash@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "micron,n25q064", "jedec,spi-nor";
diff --git a/arch/arm/boot/dts/armada-370.dtsi b/arch/arm/boot/dts/armada-370.dtsi
index 46e6d3ed8f35..9dc928859ad3 100644
--- a/arch/arm/boot/dts/armada-370.dtsi
+++ b/arch/arm/boot/dts/armada-370.dtsi
@@ -60,16 +60,26 @@
 				reg = <0x0800 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 58>;
 				#interrupt-cells = <1>;
                                 ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
                                           0x81000000 0 0 0x81000000 0x1 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 58>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie0_intc 0>,
+						<0 0 0 2 &pcie0_intc 1>,
+						<0 0 0 3 &pcie0_intc 2>,
+						<0 0 0 4 &pcie0_intc 3>;
 				marvell,pcie-port = <0>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gateclk 5>;
 				status = "disabled";
+
+				pcie0_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			pcie2: pcie@2,0 {
@@ -78,16 +88,26 @@
 				reg = <0x1000 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 62>;
 				#interrupt-cells = <1>;
                                 ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0
                                           0x81000000 0 0 0x81000000 0x2 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 62>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie2_intc 0>,
+						<0 0 0 2 &pcie2_intc 1>,
+						<0 0 0 3 &pcie2_intc 2>,
+						<0 0 0 4 &pcie2_intc 3>;
 				marvell,pcie-port = <1>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gateclk 9>;
 				status = "disabled";
+
+				pcie2_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 		};
 
diff --git a/arch/arm/boot/dts/armada-375-db.dts b/arch/arm/boot/dts/armada-375-db.dts
index 0e679465cbb5..4c4092790a20 100644
--- a/arch/arm/boot/dts/armada-375-db.dts
+++ b/arch/arm/boot/dts/armada-375-db.dts
@@ -64,7 +64,7 @@
 
 	status = "disabled";
 
-	spi-flash@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "n25q128a13", "jedec,spi-nor";
diff --git a/arch/arm/boot/dts/armada-375.dtsi b/arch/arm/boot/dts/armada-375.dtsi
index 7f2f24a29e6c..929deaf312a5 100644
--- a/arch/arm/boot/dts/armada-375.dtsi
+++ b/arch/arm/boot/dts/armada-375.dtsi
@@ -568,16 +568,26 @@
 				reg = <0x0800 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&gic GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
 					  0x81000000 0 0 0x81000000 0x1 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &gic GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie0_intc 0>,
+						<0 0 0 2 &pcie0_intc 1>,
+						<0 0 0 3 &pcie0_intc 2>,
+						<0 0 0 4 &pcie0_intc 3>;
 				marvell,pcie-port = <0>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gateclk 5>;
 				status = "disabled";
+
+				pcie0_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			pcie1: pcie@2,0 {
@@ -586,16 +596,26 @@
 				reg = <0x1000 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&gic GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0
 					  0x81000000 0 0 0x81000000 0x2 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &gic GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie1_intc 0>,
+						<0 0 0 2 &pcie1_intc 1>,
+						<0 0 0 3 &pcie1_intc 2>,
+						<0 0 0 4 &pcie1_intc 3>;
 				marvell,pcie-port = <0>;
 				marvell,pcie-lane = <1>;
 				clocks = <&gateclk 6>;
 				status = "disabled";
+
+				pcie1_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 		};
diff --git a/arch/arm/boot/dts/armada-380.dtsi b/arch/arm/boot/dts/armada-380.dtsi
index cff1269f3fbf..ce1dddb2269b 100644
--- a/arch/arm/boot/dts/armada-380.dtsi
+++ b/arch/arm/boot/dts/armada-380.dtsi
@@ -64,16 +64,26 @@
 				reg = <0x0800 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&gic GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
 					  0x81000000 0 0 0x81000000 0x1 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &gic GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie1_intc 0>,
+						<0 0 0 2 &pcie1_intc 1>,
+						<0 0 0 3 &pcie1_intc 2>,
+						<0 0 0 4 &pcie1_intc 3>;
 				marvell,pcie-port = <0>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gateclk 8>;
 				status = "disabled";
+
+				pcie1_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			/* x1 port */
@@ -83,16 +93,26 @@
 				reg = <0x1000 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&gic GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0
 					  0x81000000 0 0 0x81000000 0x2 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &gic GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie2_intc 0>,
+						<0 0 0 2 &pcie2_intc 1>,
+						<0 0 0 3 &pcie2_intc 2>,
+						<0 0 0 4 &pcie2_intc 3>;
 				marvell,pcie-port = <1>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gateclk 5>;
 				status = "disabled";
+
+				pcie2_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			/* x1 port */
@@ -102,16 +122,26 @@
 				reg = <0x1800 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&gic GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x3 0 1 0
 					  0x81000000 0 0 0x81000000 0x3 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &gic GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie3_intc 0>,
+						<0 0 0 2 &pcie3_intc 1>,
+						<0 0 0 3 &pcie3_intc 2>,
+						<0 0 0 4 &pcie3_intc 3>;
 				marvell,pcie-port = <2>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gateclk 6>;
 				status = "disabled";
+
+				pcie3_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 		};
 	};
diff --git a/arch/arm/boot/dts/armada-381-netgear-gs110emx.dts b/arch/arm/boot/dts/armada-381-netgear-gs110emx.dts
index 0a961116a1f9..095df5567c93 100644
--- a/arch/arm/boot/dts/armada-381-netgear-gs110emx.dts
+++ b/arch/arm/boot/dts/armada-381-netgear-gs110emx.dts
@@ -24,7 +24,7 @@
 		pinctrl-0 = <&front_button_pins>;
 		pinctrl-names = "default";
 
-		factory_default {
+		key-factory-default {
 			label = "Factory Default";
 			gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_RESTART>;
@@ -242,7 +242,7 @@
 	pinctrl-names = "default";
 	status = "okay";
 
-	spi-flash@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "jedec,spi-nor";
diff --git a/arch/arm/boot/dts/armada-385-atl-x530.dts b/arch/arm/boot/dts/armada-385-atl-x530.dts
index ed3f41c7df71..241f5d7c80e9 100644
--- a/arch/arm/boot/dts/armada-385-atl-x530.dts
+++ b/arch/arm/boot/dts/armada-385-atl-x530.dts
@@ -168,7 +168,7 @@
 	pinctrl-0 = <&spi1_pins>;
 	status = "okay";
 
-	spi-flash@1 {
+	flash@1 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "jedec,spi-nor";
diff --git a/arch/arm/boot/dts/armada-385-clearfog-gtr.dtsi b/arch/arm/boot/dts/armada-385-clearfog-gtr.dtsi
index 624bbcae68c0..d1452a04e904 100644
--- a/arch/arm/boot/dts/armada-385-clearfog-gtr.dtsi
+++ b/arch/arm/boot/dts/armada-385-clearfog-gtr.dtsi
@@ -256,14 +256,14 @@
 		pinctrl-0 = <&cf_gtr_rear_button_pins &cf_gtr_front_button_pins>;
 		pinctrl-names = "default";
 
-		button_0 {
+		button-0 {
 			label = "Rear Button";
 			gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
 			linux,can-disable;
 			linux,code = <BTN_0>;
 		};
 
-		button_1 {
+		button-1 {
 			label = "Front Button";
 			gpios = <&gpio1 21 GPIO_ACTIVE_LOW>;
 			linux,can-disable;
@@ -365,7 +365,7 @@
 	pinctrl-names = "default";
 	status = "okay";
 
-	spi-flash@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <0>;
 		compatible = "w25q32", "jedec,spi-nor";
diff --git a/arch/arm/boot/dts/armada-385-db-88f6820-amc.dts b/arch/arm/boot/dts/armada-385-db-88f6820-amc.dts
index 7881df3b28a0..389d9c75d546 100644
--- a/arch/arm/boot/dts/armada-385-db-88f6820-amc.dts
+++ b/arch/arm/boot/dts/armada-385-db-88f6820-amc.dts
@@ -126,7 +126,7 @@
 	pinctrl-0 = <&spi1_pins>;
 	status = "okay";
 
-	spi-flash@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "jedec,spi-nor";
diff --git a/arch/arm/boot/dts/armada-385-db-ap.dts b/arch/arm/boot/dts/armada-385-db-ap.dts
index 0e4613bb56ee..332f8fce77dc 100644
--- a/arch/arm/boot/dts/armada-385-db-ap.dts
+++ b/arch/arm/boot/dts/armada-385-db-ap.dts
@@ -192,7 +192,7 @@
 	pinctrl-0 = <&spi1_pins>;
 	status = "okay";
 
-	spi-flash@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "st,m25p128", "jedec,spi-nor";
diff --git a/arch/arm/boot/dts/armada-385-linksys.dtsi b/arch/arm/boot/dts/armada-385-linksys.dtsi
index fb9c8a0b241c..116aca5e688f 100644
--- a/arch/arm/boot/dts/armada-385-linksys.dtsi
+++ b/arch/arm/boot/dts/armada-385-linksys.dtsi
@@ -53,13 +53,13 @@
 		pinctrl-0 = <&gpio_keys_pins>;
 		pinctrl-names = "default";
 
-		wps {
+		button-wps {
 			label = "WPS";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&gpio0 24 GPIO_ACTIVE_LOW>;
 		};
 
-		reset {
+		button-reset {
 			label = "Factory Reset Button";
 			linux,code = <KEY_RESTART>;
 			gpios = <&gpio0 29 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/armada-385-synology-ds116.dts b/arch/arm/boot/dts/armada-385-synology-ds116.dts
index d8769956cbfc..2622af73c9da 100644
--- a/arch/arm/boot/dts/armada-385-synology-ds116.dts
+++ b/arch/arm/boot/dts/armada-385-synology-ds116.dts
@@ -223,7 +223,7 @@
 	pinctrl-0 = <&spi0_pins>;
 	status = "okay";
 
-	spi-flash@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "macronix,mx25l6405d", "jedec,spi-nor";
diff --git a/arch/arm/boot/dts/armada-385-turris-omnia.dts b/arch/arm/boot/dts/armada-385-turris-omnia.dts
index 5bd6a66d2c2b..72ac807cae25 100644
--- a/arch/arm/boot/dts/armada-385-turris-omnia.dts
+++ b/arch/arm/boot/dts/armada-385-turris-omnia.dts
@@ -71,16 +71,19 @@
 			pcie@1,0 {
 				/* Port 0, Lane 0 */
 				status = "okay";
+				slot-power-limit-milliwatt = <10000>;
 			};
 
 			pcie@2,0 {
 				/* Port 1, Lane 0 */
 				status = "okay";
+				slot-power-limit-milliwatt = <10000>;
 			};
 
 			pcie@3,0 {
 				/* Port 2, Lane 0 */
 				status = "okay";
+				slot-power-limit-milliwatt = <10000>;
 			};
 		};
 	};
@@ -102,6 +105,33 @@
 		 */
 		status = "disabled";
 	};
+
+	sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "SPDIF";
+		simple-audio-card,format = "i2s";
+
+		simple-audio-card,cpu {
+			sound-dai = <&audio_controller 1>;
+		};
+
+		simple-audio-card,codec {
+			sound-dai = <&spdif_out>;
+		};
+	};
+
+	spdif_out: spdif-out {
+		#sound-dai-cells = <0>;
+		compatible = "linux,spdif-dit";
+	};
+};
+
+&audio_controller {
+	/* Pin header U16, GPIO51 in SPDIFO mode */
+	pinctrl-0 = <&spdif_pins>;
+	pinctrl-names = "default";
+	spdif-mode;
+	status = "okay";
 };
 
 &bm {
@@ -163,6 +193,7 @@
 	buffer-manager = <&bm>;
 	bm,pool-long = <2>;
 	bm,pool-short = <3>;
+	label = "wan";
 };
 
 &i2c0 {
@@ -188,15 +219,13 @@
 				reg = <0x2b>;
 				#address-cells = <1>;
 				#size-cells = <0>;
+				status = "okay";
 
 				/*
 				 * LEDs are controlled by MCU (STM32F0) at
 				 * address 0x2b.
 				 *
-				 * The driver does not support HW control mode
-				 * for the LEDs yet. Disable the LEDs for now.
-				 *
-				 * Also LED functions are not stable yet:
+				 * LED functions are not stable yet:
 				 * - there are 3 LEDs connected via MCU to PCIe
 				 *   ports. One of these ports supports mSATA.
 				 *   There is no mSATA nor PCIe function.
@@ -207,7 +236,6 @@
 				 *   B. Again there is no such function defined.
 				 *   For now we use LED_FUNCTION_INDICATOR
 				 */
-				status = "disabled";
 
 				multi-led@0 {
 					reg = <0x0>;
@@ -345,7 +373,11 @@
 			#size-cells = <0>;
 			reg = <5>;
 
-			/* ATSHA204A at address 0x64 */
+			/* ATSHA204A-MAHDA-T crypto module */
+			crypto@64 {
+				compatible = "atmel,atsha204a";
+				reg = <0x64>;
+			};
 		};
 
 		i2c@6 {
@@ -390,7 +422,8 @@
 	phy1: ethernet-phy@1 {
 		compatible = "ethernet-phy-ieee802.3-c22";
 		reg = <1>;
-		marvell,reg-init = <3 18 0 0x4985>;
+		marvell,reg-init = <3 18 0 0x4985>,
+				   <3 16 0xfff0 0x0001>;
 
 		/* irq is connected to &pcawan pin 7 */
 	};
@@ -471,7 +504,7 @@
 		marvell,function = "spi0";
 	};
 
-	spi0cs1_pins: spi0cs1-pins {
+	spi0cs2_pins: spi0cs2-pins {
 		marvell,pins = "mpp26";
 		marvell,function = "spi0";
 	};
@@ -482,7 +515,7 @@
 	pinctrl-0 = <&spi0_pins &spi0cs0_pins>;
 	status = "okay";
 
-	spi-nor@0 {
+	flash@0 {
 		compatible = "spansion,s25fl164k", "jedec,spi-nor";
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -506,7 +539,7 @@
 		};
 	};
 
-	/* MISO, MOSI, SCLK and CS1 are routed to pin header CN11 */
+	/* MISO, MOSI, SCLK and CS2 are routed to pin header CN11 */
 };
 
 &uart0 {
diff --git a/arch/arm/boot/dts/armada-385.dtsi b/arch/arm/boot/dts/armada-385.dtsi
index f0022d10c715..83392b92dae2 100644
--- a/arch/arm/boot/dts/armada-385.dtsi
+++ b/arch/arm/boot/dts/armada-385.dtsi
@@ -69,16 +69,25 @@
 				reg = <0x0800 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&gic GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
 					  0x81000000 0 0 0x81000000 0x1 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &gic GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie1_intc 0>,
+						<0 0 0 2 &pcie1_intc 1>,
+						<0 0 0 3 &pcie1_intc 2>,
+						<0 0 0 4 &pcie1_intc 3>;
 				marvell,pcie-port = <0>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gateclk 8>;
 				status = "disabled";
+				pcie1_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			/* x1 port */
@@ -88,16 +97,25 @@
 				reg = <0x1000 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&gic GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0
 					  0x81000000 0 0 0x81000000 0x2 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &gic GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie2_intc 0>,
+						<0 0 0 2 &pcie2_intc 1>,
+						<0 0 0 3 &pcie2_intc 2>,
+						<0 0 0 4 &pcie2_intc 3>;
 				marvell,pcie-port = <1>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gateclk 5>;
 				status = "disabled";
+				pcie2_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			/* x1 port */
@@ -107,16 +125,25 @@
 				reg = <0x1800 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&gic GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x3 0 1 0
 					  0x81000000 0 0 0x81000000 0x3 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &gic GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie3_intc 0>,
+						<0 0 0 2 &pcie3_intc 1>,
+						<0 0 0 3 &pcie3_intc 2>,
+						<0 0 0 4 &pcie3_intc 3>;
 				marvell,pcie-port = <2>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gateclk 6>;
 				status = "disabled";
+				pcie3_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			/*
@@ -129,16 +156,25 @@
 				reg = <0x2000 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&gic GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x4 0 1 0
 					  0x81000000 0 0 0x81000000 0x4 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &gic GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie4_intc 0>,
+						<0 0 0 2 &pcie4_intc 1>,
+						<0 0 0 3 &pcie4_intc 2>,
+						<0 0 0 4 &pcie4_intc 3>;
 				marvell,pcie-port = <3>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gateclk 7>;
 				status = "disabled";
+				pcie4_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 		};
 	};
diff --git a/arch/arm/boot/dts/armada-388-clearfog-base.dts b/arch/arm/boot/dts/armada-388-clearfog-base.dts
index 53b4bd35522a..f7daa3bc707e 100644
--- a/arch/arm/boot/dts/armada-388-clearfog-base.dts
+++ b/arch/arm/boot/dts/armada-388-clearfog-base.dts
@@ -19,7 +19,7 @@
 		pinctrl-0 = <&rear_button_pins>;
 		pinctrl-names = "default";
 
-		button_0 {
+		button-0 {
 			/* The rear SW3 button */
 			label = "Rear Button";
 			gpios = <&gpio1 12 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/armada-388-clearfog.dts b/arch/arm/boot/dts/armada-388-clearfog.dts
index 4140a5303b48..95299167dcf5 100644
--- a/arch/arm/boot/dts/armada-388-clearfog.dts
+++ b/arch/arm/boot/dts/armada-388-clearfog.dts
@@ -35,7 +35,7 @@
 		pinctrl-0 = <&rear_button_pins>;
 		pinctrl-names = "default";
 
-		button_0 {
+		button-0 {
 			/* The rear SW3 button */
 			label = "Rear Button";
 			gpios = <&gpio1 2 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/armada-388-db.dts b/arch/arm/boot/dts/armada-388-db.dts
index a2bec07bf4c5..2bcec5419b66 100644
--- a/arch/arm/boot/dts/armada-388-db.dts
+++ b/arch/arm/boot/dts/armada-388-db.dts
@@ -36,6 +36,11 @@
 			i2c@11000 {
 				status = "okay";
 				clock-frequency = <100000>;
+				audio_codec: audio-codec@4a {
+					#sound-dai-cells = <0>;
+					compatible = "cirrus,cs42l51";
+					reg = <0x4a>;
+				};
 			};
 
 			i2c@11100 {
@@ -99,6 +104,12 @@
 				no-1-8-v;
 			};
 
+			audio-controller@e8000 {
+				pinctrl-0 = <&i2s_pins>;
+				pinctrl-names = "default";
+				status = "disabled";
+			};
+
 			usb3@f0000 {
 				status = "okay";
 			};
@@ -128,12 +139,70 @@
 			};
 		};
 	};
+
+	sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "Armada 385 DB Audio";
+		simple-audio-card,mclk-fs = <256>;
+		simple-audio-card,widgets =
+			"Headphone", "Out Jack",
+			"Line", "In Jack";
+		simple-audio-card,routing =
+			"Out Jack", "HPL",
+			"Out Jack", "HPR",
+			"AIN1L", "In Jack",
+			"AIN1R", "In Jack";
+		status = "disabled";
+
+		simple-audio-card,dai-link@0 {
+			format = "i2s";
+			cpu {
+				sound-dai = <&audio_controller 0>;
+			};
+
+			codec {
+				sound-dai = <&audio_codec>;
+			};
+		};
+
+		simple-audio-card,dai-link@1 {
+			format = "i2s";
+			cpu {
+				sound-dai = <&audio_controller 1>;
+			};
+
+			codec {
+				sound-dai = <&spdif_out>;
+			};
+		};
+
+		simple-audio-card,dai-link@2 {
+			format = "i2s";
+			cpu {
+				sound-dai = <&audio_controller 1>;
+			};
+
+			codec {
+				sound-dai = <&spdif_in>;
+			};
+		};
+	};
+
+	spdif_out: spdif-out {
+		#sound-dai-cells = <0>;
+		compatible = "linux,spdif-dit";
+	};
+
+	spdif_in: spdif-in {
+		#sound-dai-cells = <0>;
+		compatible = "linux,spdif-dir";
+	};
 };
 
 &spi0 {
 	status = "okay";
 
-	spi-flash@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "w25q32", "jedec,spi-nor";
diff --git a/arch/arm/boot/dts/armada-388-gp.dts b/arch/arm/boot/dts/armada-388-gp.dts
index 9d873257ac45..e2ba50520b6b 100644
--- a/arch/arm/boot/dts/armada-388-gp.dts
+++ b/arch/arm/boot/dts/armada-388-gp.dts
@@ -395,7 +395,7 @@
 	pinctrl-0 = <&spi0_pins>;
 	status = "okay";
 
-	spi-flash@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "st,m25p128", "jedec,spi-nor";
diff --git a/arch/arm/boot/dts/armada-388-rd.dts b/arch/arm/boot/dts/armada-388-rd.dts
index 328a4d6afd2c..c0efafd45b33 100644
--- a/arch/arm/boot/dts/armada-388-rd.dts
+++ b/arch/arm/boot/dts/armada-388-rd.dts
@@ -97,7 +97,7 @@
 &spi0 {
 	status = "okay";
 
-	spi-flash@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "st,m25p128", "jedec,spi-nor";
diff --git a/arch/arm/boot/dts/armada-38x-solidrun-microsom.dtsi b/arch/arm/boot/dts/armada-38x-solidrun-microsom.dtsi
index 363ac4238859..2c64bc6e5a17 100644
--- a/arch/arm/boot/dts/armada-38x-solidrun-microsom.dtsi
+++ b/arch/arm/boot/dts/armada-38x-solidrun-microsom.dtsi
@@ -101,7 +101,7 @@
 	/* The microsom has an optional W25Q32 on board, connected to CS0 */
 	pinctrl-0 = <&spi1_pins>;
 
-	w25q32: spi-flash@0 {
+	w25q32: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "w25q32", "jedec,spi-nor";
diff --git a/arch/arm/boot/dts/armada-38x.dtsi b/arch/arm/boot/dts/armada-38x.dtsi
index 9b1a24cc5e91..446861b6b17b 100644
--- a/arch/arm/boot/dts/armada-38x.dtsi
+++ b/arch/arm/boot/dts/armada-38x.dtsi
@@ -168,7 +168,7 @@
 			};
 
 			uart0: serial@12000 {
-				compatible = "marvell,armada-38x-uart";
+				compatible = "marvell,armada-38x-uart", "ns16550a";
 				reg = <0x12000 0x100>;
 				reg-shift = <2>;
 				interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
@@ -178,7 +178,7 @@
 			};
 
 			uart1: serial@12100 {
-				compatible = "marvell,armada-38x-uart";
+				compatible = "marvell,armada-38x-uart", "ns16550a";
 				reg = <0x12100 0x100>;
 				reg-shift = <2>;
 				interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
@@ -289,6 +289,18 @@
 					marvell,pins = "mpp44";
 					marvell,function = "sata3";
 				};
+
+				i2s_pins: i2s-pins {
+					marvell,pins = "mpp48", "mpp49",
+						       "mpp50", "mpp51",
+						       "mpp52", "mpp53";
+					marvell,function = "audio";
+				};
+
+				spdif_pins: spdif-pins {
+					marvell,pins = "mpp51";
+					marvell,function = "audio";
+				};
 			};
 
 			gpio0: gpio@18100 {
@@ -298,6 +310,7 @@
 				reg-names = "gpio", "pwm";
 				ngpios = <32>;
 				gpio-controller;
+				gpio-ranges = <&pinctrl 0 0 32>;
 				#gpio-cells = <2>;
 				#pwm-cells = <2>;
 				interrupt-controller;
@@ -316,6 +329,7 @@
 				reg-names = "gpio", "pwm";
 				ngpios = <28>;
 				gpio-controller;
+				gpio-ranges = <&pinctrl 0 32 28>;
 				#gpio-cells = <2>;
 				#pwm-cells = <2>;
 				interrupt-controller;
@@ -618,6 +632,18 @@
 				status = "disabled";
 			};
 
+			audio_controller: audio-controller@e8000 {
+				#sound-dai-cells = <1>;
+				compatible = "marvell,armada-380-audio";
+				reg = <0xe8000 0x4000>, <0x18410 0xc>,
+				      <0x18204 0x4>;
+				reg-names = "i2s_regs", "pll_regs", "soc_ctrl";
+				interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gateclk 0>;
+				clock-names = "internal";
+				status = "disabled";
+			};
+
 			usb3_0: usb3@f0000 {
 				compatible = "marvell,armada-380-xhci";
 				reg = <0xf0000 0x4000>,<0xf4000 0x4000>;
diff --git a/arch/arm/boot/dts/armada-390-db.dts b/arch/arm/boot/dts/armada-390-db.dts
index 0e29474ae9a2..792d0a0184e8 100644
--- a/arch/arm/boot/dts/armada-390-db.dts
+++ b/arch/arm/boot/dts/armada-390-db.dts
@@ -81,7 +81,7 @@
 	pinctrl-0 = <&spi1_pins>;
 	pinctrl-names = "default";
 
-	spi-flash@1 {
+	flash@1 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "n25q128a13",
diff --git a/arch/arm/boot/dts/armada-398-db.dts b/arch/arm/boot/dts/armada-398-db.dts
index fc28308e5bc5..ec6cdbeedde7 100644
--- a/arch/arm/boot/dts/armada-398-db.dts
+++ b/arch/arm/boot/dts/armada-398-db.dts
@@ -79,7 +79,7 @@
 	pinctrl-0 = <&spi1_pins>;
 	pinctrl-names = "default";
 
-	spi-flash@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <0>;
 		compatible = "n25q128a13", "jedec,spi-nor";
diff --git a/arch/arm/boot/dts/armada-39x.dtsi b/arch/arm/boot/dts/armada-39x.dtsi
index e0b7c2099831..923b035a3ab3 100644
--- a/arch/arm/boot/dts/armada-39x.dtsi
+++ b/arch/arm/boot/dts/armada-39x.dtsi
@@ -438,16 +438,26 @@
 				reg = <0x0800 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&gic GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
 					  0x81000000 0 0 0x81000000 0x1 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &gic GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie1_intc 0>,
+						<0 0 0 2 &pcie1_intc 1>,
+						<0 0 0 3 &pcie1_intc 2>,
+						<0 0 0 4 &pcie1_intc 3>;
 				marvell,pcie-port = <0>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gateclk 8>;
 				status = "disabled";
+
+				pcie1_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			/* x1 port */
@@ -457,16 +467,26 @@
 				reg = <0x1000 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&gic GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0
 					  0x81000000 0 0 0x81000000 0x2 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &gic GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie2_intc 0>,
+						<0 0 0 2 &pcie2_intc 1>,
+						<0 0 0 3 &pcie2_intc 2>,
+						<0 0 0 4 &pcie2_intc 3>;
 				marvell,pcie-port = <1>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gateclk 5>;
 				status = "disabled";
+
+				pcie2_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			/* x1 port */
@@ -476,16 +496,26 @@
 				reg = <0x1800 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&gic GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x3 0 1 0
 					  0x81000000 0 0 0x81000000 0x3 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &gic GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie3_intc 0>,
+						<0 0 0 2 &pcie3_intc 1>,
+						<0 0 0 3 &pcie3_intc 2>,
+						<0 0 0 4 &pcie3_intc 3>;
 				marvell,pcie-port = <2>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gateclk 6>;
 				status = "disabled";
+
+				pcie3_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			/*
@@ -498,16 +528,26 @@
 				reg = <0x2000 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&gic GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x4 0 1 0
 					  0x81000000 0 0 0x81000000 0x4 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &gic GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie4_intc 0>,
+						<0 0 0 2 &pcie4_intc 1>,
+						<0 0 0 3 &pcie4_intc 2>,
+						<0 0 0 4 &pcie4_intc 3>;
 				marvell,pcie-port = <3>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gateclk 7>;
 				status = "disabled";
+
+				pcie4_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 		};
 
diff --git a/arch/arm/boot/dts/armada-xp-98dx3236.dtsi b/arch/arm/boot/dts/armada-xp-98dx3236.dtsi
index 38a052a0312d..b21ffb819b1d 100644
--- a/arch/arm/boot/dts/armada-xp-98dx3236.dtsi
+++ b/arch/arm/boot/dts/armada-xp-98dx3236.dtsi
@@ -76,16 +76,26 @@
 				reg = <0x0800 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 58>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
 					  0x81000000 0 0 0x81000000 0x1 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 58>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie1_intc 0>,
+						<0 0 0 2 &pcie1_intc 1>,
+						<0 0 0 3 &pcie1_intc 2>,
+						<0 0 0 4 &pcie1_intc 3>;
 				marvell,pcie-port = <0>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gateclk 5>;
 				status = "disabled";
+
+				pcie1_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 		};
 
diff --git a/arch/arm/boot/dts/armada-xp-axpwifiap.dts b/arch/arm/boot/dts/armada-xp-axpwifiap.dts
index 606fd3476a59..5a74197be0ad 100644
--- a/arch/arm/boot/dts/armada-xp-axpwifiap.dts
+++ b/arch/arm/boot/dts/armada-xp-axpwifiap.dts
@@ -69,14 +69,12 @@
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		pinctrl-0 = <&keys_pin>;
 		pinctrl-names = "default";
 
-		reset {
+		button-reset {
 			label = "Factory Reset Button";
 			linux,code = <KEY_SETUP>;
 			gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
@@ -134,7 +132,7 @@
 &spi0 {
 	status = "okay";
 
-	spi-flash@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "n25q128a13", "jedec,spi-nor";
diff --git a/arch/arm/boot/dts/armada-xp-crs305-1g-4s-bit.dts b/arch/arm/boot/dts/armada-xp-crs305-1g-4s-bit.dts
index a022c68dc943..c28e140b4afc 100644
--- a/arch/arm/boot/dts/armada-xp-crs305-1g-4s-bit.dts
+++ b/arch/arm/boot/dts/armada-xp-crs305-1g-4s-bit.dts
@@ -15,7 +15,7 @@
 &spi0 {
 	status = "okay";
 
-	spi-flash@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "jedec,spi-nor";
diff --git a/arch/arm/boot/dts/armada-xp-crs305-1g-4s.dtsi b/arch/arm/boot/dts/armada-xp-crs305-1g-4s.dtsi
index 32fb21b2bf6a..47b003a81bd4 100644
--- a/arch/arm/boot/dts/armada-xp-crs305-1g-4s.dtsi
+++ b/arch/arm/boot/dts/armada-xp-crs305-1g-4s.dtsi
@@ -80,7 +80,7 @@
 &spi0 {
 	status = "okay";
 
-	spi-flash@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "jedec,spi-nor";
diff --git a/arch/arm/boot/dts/armada-xp-crs326-24g-2s-bit.dts b/arch/arm/boot/dts/armada-xp-crs326-24g-2s-bit.dts
index 21f442afab1f..20ba5c823bb2 100644
--- a/arch/arm/boot/dts/armada-xp-crs326-24g-2s-bit.dts
+++ b/arch/arm/boot/dts/armada-xp-crs326-24g-2s-bit.dts
@@ -15,7 +15,7 @@
 &spi0 {
 	status = "okay";
 
-	spi-flash@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "jedec,spi-nor";
diff --git a/arch/arm/boot/dts/armada-xp-crs326-24g-2s.dtsi b/arch/arm/boot/dts/armada-xp-crs326-24g-2s.dtsi
index f3e1a25ca5f2..cab99d8e2911 100644
--- a/arch/arm/boot/dts/armada-xp-crs326-24g-2s.dtsi
+++ b/arch/arm/boot/dts/armada-xp-crs326-24g-2s.dtsi
@@ -80,7 +80,7 @@
 &spi0 {
 	status = "okay";
 
-	spi-flash@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "jedec,spi-nor";
diff --git a/arch/arm/boot/dts/armada-xp-crs328-4c-20s-4s-bit.dts b/arch/arm/boot/dts/armada-xp-crs328-4c-20s-4s-bit.dts
index e05aee6cdc04..2caa3980fdf6 100644
--- a/arch/arm/boot/dts/armada-xp-crs328-4c-20s-4s-bit.dts
+++ b/arch/arm/boot/dts/armada-xp-crs328-4c-20s-4s-bit.dts
@@ -15,7 +15,7 @@
 &spi0 {
 	status = "okay";
 
-	spi-flash@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "jedec,spi-nor";
diff --git a/arch/arm/boot/dts/armada-xp-crs328-4c-20s-4s.dtsi b/arch/arm/boot/dts/armada-xp-crs328-4c-20s-4s.dtsi
index c8b1355ce15e..7028482ce4b2 100644
--- a/arch/arm/boot/dts/armada-xp-crs328-4c-20s-4s.dtsi
+++ b/arch/arm/boot/dts/armada-xp-crs328-4c-20s-4s.dtsi
@@ -80,7 +80,7 @@
 &spi0 {
 	status = "okay";
 
-	spi-flash@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "jedec,spi-nor";
diff --git a/arch/arm/boot/dts/armada-xp-db-dxbc2.dts b/arch/arm/boot/dts/armada-xp-db-dxbc2.dts
index 8a3aa616bbd0..02bef8dc4270 100644
--- a/arch/arm/boot/dts/armada-xp-db-dxbc2.dts
+++ b/arch/arm/boot/dts/armada-xp-db-dxbc2.dts
@@ -93,7 +93,7 @@
 &spi0 {
 	status = "okay";
 
-	spi-flash@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "m25p64";
diff --git a/arch/arm/boot/dts/armada-xp-db-xc3-24g4xg.dts b/arch/arm/boot/dts/armada-xp-db-xc3-24g4xg.dts
index 4ec0ae01b61d..d1b61dad0c46 100644
--- a/arch/arm/boot/dts/armada-xp-db-xc3-24g4xg.dts
+++ b/arch/arm/boot/dts/armada-xp-db-xc3-24g4xg.dts
@@ -89,7 +89,7 @@
 &spi0 {
 	status = "okay";
 
-	spi-flash@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "m25p64";
diff --git a/arch/arm/boot/dts/armada-xp-db.dts b/arch/arm/boot/dts/armada-xp-db.dts
index 5d04dc68cf57..75318fd0fc11 100644
--- a/arch/arm/boot/dts/armada-xp-db.dts
+++ b/arch/arm/boot/dts/armada-xp-db.dts
@@ -235,7 +235,7 @@
 &spi0 {
 	status = "okay";
 
-	spi-flash@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "m25p64", "jedec,spi-nor";
diff --git a/arch/arm/boot/dts/armada-xp-gp.dts b/arch/arm/boot/dts/armada-xp-gp.dts
index b4cca507cf13..d1d348b91c0a 100644
--- a/arch/arm/boot/dts/armada-xp-gp.dts
+++ b/arch/arm/boot/dts/armada-xp-gp.dts
@@ -220,7 +220,7 @@
 &spi0 {
 	status = "okay";
 
-	spi-flash@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "n25q128a13", "jedec,spi-nor";
diff --git a/arch/arm/boot/dts/armada-xp-lenovo-ix4-300d.dts b/arch/arm/boot/dts/armada-xp-lenovo-ix4-300d.dts
index 87dcb502f72d..0dad95ea26c2 100644
--- a/arch/arm/boot/dts/armada-xp-lenovo-ix4-300d.dts
+++ b/arch/arm/boot/dts/armada-xp-lenovo-ix4-300d.dts
@@ -164,7 +164,7 @@
 		};
 	};
 
-	spi3 {
+	spi-3 {
 		compatible = "spi-gpio";
 		status = "okay";
 		gpio-sck = <&gpio0 25 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/armada-xp-linksys-mamba.dts b/arch/arm/boot/dts/armada-xp-linksys-mamba.dts
index 8480a16919a0..622ac40dd164 100644
--- a/arch/arm/boot/dts/armada-xp-linksys-mamba.dts
+++ b/arch/arm/boot/dts/armada-xp-linksys-mamba.dts
@@ -172,20 +172,18 @@
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		pinctrl-0 = <&keys_pin>;
 		pinctrl-names = "default";
 
-		wps {
+		button-wps {
 			label = "WPS";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
 		};
 
-		reset {
+		button-reset {
 			label = "Factory Reset Button";
 			linux,code = <KEY_RESTART>;
 			gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
@@ -255,7 +253,7 @@
 &spi0 {
 	status = "okay";
 
-	spi-flash@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "everspin,mr25h256";
diff --git a/arch/arm/boot/dts/armada-xp-mv78230.dtsi b/arch/arm/boot/dts/armada-xp-mv78230.dtsi
index 8558bf6bb54c..bf9360f41e0a 100644
--- a/arch/arm/boot/dts/armada-xp-mv78230.dtsi
+++ b/arch/arm/boot/dts/armada-xp-mv78230.dtsi
@@ -83,16 +83,26 @@
 				reg = <0x0800 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 58>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
 					  0x81000000 0 0 0x81000000 0x1 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 58>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie1_intc 0>,
+						<0 0 0 2 &pcie1_intc 1>,
+						<0 0 0 3 &pcie1_intc 2>,
+						<0 0 0 4 &pcie1_intc 3>;
 				marvell,pcie-port = <0>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gateclk 5>;
 				status = "disabled";
+
+				pcie1_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			pcie2: pcie@2,0 {
@@ -101,16 +111,26 @@
 				reg = <0x1000 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 59>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0
 					  0x81000000 0 0 0x81000000 0x2 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 59>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie2_intc 0>,
+						<0 0 0 2 &pcie2_intc 1>,
+						<0 0 0 3 &pcie2_intc 2>,
+						<0 0 0 4 &pcie2_intc 3>;
 				marvell,pcie-port = <0>;
 				marvell,pcie-lane = <1>;
 				clocks = <&gateclk 6>;
 				status = "disabled";
+
+				pcie2_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			pcie3: pcie@3,0 {
@@ -119,16 +139,26 @@
 				reg = <0x1800 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 60>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x3 0 1 0
 					  0x81000000 0 0 0x81000000 0x3 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 60>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie3_intc 0>,
+						<0 0 0 2 &pcie3_intc 1>,
+						<0 0 0 3 &pcie3_intc 2>,
+						<0 0 0 4 &pcie3_intc 3>;
 				marvell,pcie-port = <0>;
 				marvell,pcie-lane = <2>;
 				clocks = <&gateclk 7>;
 				status = "disabled";
+
+				pcie3_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			pcie4: pcie@4,0 {
@@ -137,16 +167,26 @@
 				reg = <0x2000 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 61>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x4 0 1 0
 					  0x81000000 0 0 0x81000000 0x4 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 61>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie4_intc 0>,
+						<0 0 0 2 &pcie4_intc 1>,
+						<0 0 0 3 &pcie4_intc 2>,
+						<0 0 0 4 &pcie4_intc 3>;
 				marvell,pcie-port = <0>;
 				marvell,pcie-lane = <3>;
 				clocks = <&gateclk 8>;
 				status = "disabled";
+
+				pcie4_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			pcie5: pcie@5,0 {
@@ -155,16 +195,26 @@
 				reg = <0x2800 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 62>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x5 0 1 0
 					  0x81000000 0 0 0x81000000 0x5 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 62>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie5_intc 0>,
+						<0 0 0 2 &pcie5_intc 1>,
+						<0 0 0 3 &pcie5_intc 2>,
+						<0 0 0 4 &pcie5_intc 3>;
 				marvell,pcie-port = <1>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gateclk 9>;
 				status = "disabled";
+
+				pcie5_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 		};
 
diff --git a/arch/arm/boot/dts/armada-xp-mv78260.dtsi b/arch/arm/boot/dts/armada-xp-mv78260.dtsi
index 2d85fe8ac327..0714af52e607 100644
--- a/arch/arm/boot/dts/armada-xp-mv78260.dtsi
+++ b/arch/arm/boot/dts/armada-xp-mv78260.dtsi
@@ -98,16 +98,26 @@
 				reg = <0x0800 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 58>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
 					  0x81000000 0 0 0x81000000 0x1 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 58>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie1_intc 0>,
+						<0 0 0 2 &pcie1_intc 1>,
+						<0 0 0 3 &pcie1_intc 2>,
+						<0 0 0 4 &pcie1_intc 3>;
 				marvell,pcie-port = <0>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gateclk 5>;
 				status = "disabled";
+
+				pcie1_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			pcie2: pcie@2,0 {
@@ -116,16 +126,26 @@
 				reg = <0x1000 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 59>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0
 					  0x81000000 0 0 0x81000000 0x2 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 59>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie2_intc 0>,
+						<0 0 0 2 &pcie2_intc 1>,
+						<0 0 0 3 &pcie2_intc 2>,
+						<0 0 0 4 &pcie2_intc 3>;
 				marvell,pcie-port = <0>;
 				marvell,pcie-lane = <1>;
 				clocks = <&gateclk 6>;
 				status = "disabled";
+
+				pcie2_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			pcie3: pcie@3,0 {
@@ -134,16 +154,26 @@
 				reg = <0x1800 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 60>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x3 0 1 0
 					  0x81000000 0 0 0x81000000 0x3 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 60>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie3_intc 0>,
+						<0 0 0 2 &pcie3_intc 1>,
+						<0 0 0 3 &pcie3_intc 2>,
+						<0 0 0 4 &pcie3_intc 3>;
 				marvell,pcie-port = <0>;
 				marvell,pcie-lane = <2>;
 				clocks = <&gateclk 7>;
 				status = "disabled";
+
+				pcie3_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			pcie4: pcie@4,0 {
@@ -152,16 +182,26 @@
 				reg = <0x2000 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 61>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x4 0 1 0
 					  0x81000000 0 0 0x81000000 0x4 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 61>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie4_intc 0>,
+						<0 0 0 2 &pcie4_intc 1>,
+						<0 0 0 3 &pcie4_intc 2>,
+						<0 0 0 4 &pcie4_intc 3>;
 				marvell,pcie-port = <0>;
 				marvell,pcie-lane = <3>;
 				clocks = <&gateclk 8>;
 				status = "disabled";
+
+				pcie4_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			pcie5: pcie@5,0 {
@@ -170,16 +210,26 @@
 				reg = <0x2800 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 62>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x5 0 1 0
 					  0x81000000 0 0 0x81000000 0x5 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 62>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie5_intc 0>,
+						<0 0 0 2 &pcie5_intc 1>,
+						<0 0 0 3 &pcie5_intc 2>,
+						<0 0 0 4 &pcie5_intc 3>;
 				marvell,pcie-port = <1>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gateclk 9>;
 				status = "disabled";
+
+				pcie5_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			pcie6: pcie@6,0 {
@@ -188,16 +238,26 @@
 				reg = <0x3000 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 63>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x6 0 1 0
 					  0x81000000 0 0 0x81000000 0x6 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 63>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie6_intc 0>,
+						<0 0 0 2 &pcie6_intc 1>,
+						<0 0 0 3 &pcie6_intc 2>,
+						<0 0 0 4 &pcie6_intc 3>;
 				marvell,pcie-port = <1>;
 				marvell,pcie-lane = <1>;
 				clocks = <&gateclk 10>;
 				status = "disabled";
+
+				pcie6_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			pcie7: pcie@7,0 {
@@ -206,16 +266,26 @@
 				reg = <0x3800 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 64>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x7 0 1 0
 					  0x81000000 0 0 0x81000000 0x7 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 64>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie7_intc 0>,
+						<0 0 0 2 &pcie7_intc 1>,
+						<0 0 0 3 &pcie7_intc 2>,
+						<0 0 0 4 &pcie7_intc 3>;
 				marvell,pcie-port = <1>;
 				marvell,pcie-lane = <2>;
 				clocks = <&gateclk 11>;
 				status = "disabled";
+
+				pcie7_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			pcie8: pcie@8,0 {
@@ -224,16 +294,26 @@
 				reg = <0x4000 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 65>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x8 0 1 0
 					  0x81000000 0 0 0x81000000 0x8 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 65>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie8_intc 0>,
+						<0 0 0 2 &pcie8_intc 1>,
+						<0 0 0 3 &pcie8_intc 2>,
+						<0 0 0 4 &pcie8_intc 3>;
 				marvell,pcie-port = <1>;
 				marvell,pcie-lane = <3>;
 				clocks = <&gateclk 12>;
 				status = "disabled";
+
+				pcie8_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			pcie9: pcie@9,0 {
@@ -242,16 +322,26 @@
 				reg = <0x4800 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 99>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x9 0 1 0
 					  0x81000000 0 0 0x81000000 0x9 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 99>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie9_intc 0>,
+						<0 0 0 2 &pcie9_intc 1>,
+						<0 0 0 3 &pcie9_intc 2>,
+						<0 0 0 4 &pcie9_intc 3>;
 				marvell,pcie-port = <2>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gateclk 26>;
 				status = "disabled";
+
+				pcie9_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 		};
 
diff --git a/arch/arm/boot/dts/armada-xp-mv78460.dtsi b/arch/arm/boot/dts/armada-xp-mv78460.dtsi
index 230a3fd36b30..16185edf9aa5 100644
--- a/arch/arm/boot/dts/armada-xp-mv78460.dtsi
+++ b/arch/arm/boot/dts/armada-xp-mv78460.dtsi
@@ -119,16 +119,26 @@
 				reg = <0x0800 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 58>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
 					  0x81000000 0 0 0x81000000 0x1 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 58>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie1_intc 0>,
+						<0 0 0 2 &pcie1_intc 1>,
+						<0 0 0 3 &pcie1_intc 2>,
+						<0 0 0 4 &pcie1_intc 3>;
 				marvell,pcie-port = <0>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gateclk 5>;
 				status = "disabled";
+
+				pcie1_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			pcie2: pcie@2,0 {
@@ -137,16 +147,26 @@
 				reg = <0x1000 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 59>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0
 					  0x81000000 0 0 0x81000000 0x2 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 59>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie2_intc 0>,
+						<0 0 0 2 &pcie2_intc 1>,
+						<0 0 0 3 &pcie2_intc 2>,
+						<0 0 0 4 &pcie2_intc 3>;
 				marvell,pcie-port = <0>;
 				marvell,pcie-lane = <1>;
 				clocks = <&gateclk 6>;
 				status = "disabled";
+
+				pcie2_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			pcie3: pcie@3,0 {
@@ -155,16 +175,26 @@
 				reg = <0x1800 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 60>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x3 0 1 0
 					  0x81000000 0 0 0x81000000 0x3 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 60>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie3_intc 0>,
+						<0 0 0 2 &pcie3_intc 1>,
+						<0 0 0 3 &pcie3_intc 2>,
+						<0 0 0 4 &pcie3_intc 3>;
 				marvell,pcie-port = <0>;
 				marvell,pcie-lane = <2>;
 				clocks = <&gateclk 7>;
 				status = "disabled";
+
+				pcie3_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			pcie4: pcie@4,0 {
@@ -173,16 +203,26 @@
 				reg = <0x2000 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 61>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x4 0 1 0
 					  0x81000000 0 0 0x81000000 0x4 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 61>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie4_intc 0>,
+						<0 0 0 2 &pcie4_intc 1>,
+						<0 0 0 3 &pcie4_intc 2>,
+						<0 0 0 4 &pcie4_intc 3>;
 				marvell,pcie-port = <0>;
 				marvell,pcie-lane = <3>;
 				clocks = <&gateclk 8>;
 				status = "disabled";
+
+				pcie4_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			pcie5: pcie@5,0 {
@@ -191,16 +231,26 @@
 				reg = <0x2800 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 62>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x5 0 1 0
 					  0x81000000 0 0 0x81000000 0x5 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 62>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie5_intc 0>,
+						<0 0 0 2 &pcie5_intc 1>,
+						<0 0 0 3 &pcie5_intc 2>,
+						<0 0 0 4 &pcie5_intc 3>;
 				marvell,pcie-port = <1>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gateclk 9>;
 				status = "disabled";
+
+				pcie5_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			pcie6: pcie@6,0 {
@@ -209,16 +259,26 @@
 				reg = <0x3000 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 63>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x6 0 1 0
 					  0x81000000 0 0 0x81000000 0x6 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 63>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie6_intc 0>,
+						<0 0 0 2 &pcie6_intc 1>,
+						<0 0 0 3 &pcie6_intc 2>,
+						<0 0 0 4 &pcie6_intc 3>;
 				marvell,pcie-port = <1>;
 				marvell,pcie-lane = <1>;
 				clocks = <&gateclk 10>;
 				status = "disabled";
+
+				pcie6_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			pcie7: pcie@7,0 {
@@ -227,16 +287,26 @@
 				reg = <0x3800 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 64>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x7 0 1 0
 					  0x81000000 0 0 0x81000000 0x7 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 64>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie7_intc 0>,
+						<0 0 0 2 &pcie7_intc 1>,
+						<0 0 0 3 &pcie7_intc 2>,
+						<0 0 0 4 &pcie7_intc 3>;
 				marvell,pcie-port = <1>;
 				marvell,pcie-lane = <2>;
 				clocks = <&gateclk 11>;
 				status = "disabled";
+
+				pcie7_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			pcie8: pcie@8,0 {
@@ -245,16 +315,26 @@
 				reg = <0x4000 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 65>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x8 0 1 0
 					  0x81000000 0 0 0x81000000 0x8 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 65>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie8_intc 0>,
+						<0 0 0 2 &pcie8_intc 1>,
+						<0 0 0 3 &pcie8_intc 2>,
+						<0 0 0 4 &pcie8_intc 3>;
 				marvell,pcie-port = <1>;
 				marvell,pcie-lane = <3>;
 				clocks = <&gateclk 12>;
 				status = "disabled";
+
+				pcie8_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			pcie9: pcie@9,0 {
@@ -263,16 +343,26 @@
 				reg = <0x4800 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 99>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0x9 0 1 0
 					  0x81000000 0 0 0x81000000 0x9 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 99>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie9_intc 0>,
+						<0 0 0 2 &pcie9_intc 1>,
+						<0 0 0 3 &pcie9_intc 2>,
+						<0 0 0 4 &pcie9_intc 3>;
 				marvell,pcie-port = <2>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gateclk 26>;
 				status = "disabled";
+
+				pcie9_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			pcie10: pcie@a,0 {
@@ -281,16 +371,26 @@
 				reg = <0x5000 0 0 0 0>;
 				#address-cells = <3>;
 				#size-cells = <2>;
+				interrupt-names = "intx";
+				interrupts-extended = <&mpic 103>;
 				#interrupt-cells = <1>;
 				ranges = <0x82000000 0 0 0x82000000 0xa 0 1 0
 					  0x81000000 0 0 0x81000000 0xa 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &mpic 103>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie10_intc 0>,
+						<0 0 0 2 &pcie10_intc 1>,
+						<0 0 0 3 &pcie10_intc 2>,
+						<0 0 0 4 &pcie10_intc 3>;
 				marvell,pcie-port = <3>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gateclk 27>;
 				status = "disabled";
+
+				pcie10_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 		};
 
diff --git a/arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts b/arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts
index 0efcc166dabf..1ecf72a61bca 100644
--- a/arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts
+++ b/arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts
@@ -97,12 +97,10 @@
 				};
 			};
 
-			gpio_keys {
+			gpio-keys {
 				compatible = "gpio-keys";
-				#address-cells = <1>;
-				#size-cells = <0>;
 
-				init {
+				button-init {
 					label = "Init Button";
 					linux,code = <KEY_POWER>;
 					gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>;
diff --git a/arch/arm/boot/dts/armada-xp-synology-ds414.dts b/arch/arm/boot/dts/armada-xp-synology-ds414.dts
index 809e821d7399..5551bac1962c 100644
--- a/arch/arm/boot/dts/armada-xp-synology-ds414.dts
+++ b/arch/arm/boot/dts/armada-xp-synology-ds414.dts
@@ -274,7 +274,7 @@
 &spi0 {
 	status = "okay";
 
-	spi-flash@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "micron,n25q064", "jedec,spi-nor";
diff --git a/arch/arm/boot/dts/artpec6-devboard.dts b/arch/arm/boot/dts/artpec6-devboard.dts
index d20d95359b28..042a9cc920c6 100644
--- a/arch/arm/boot/dts/artpec6-devboard.dts
+++ b/arch/arm/boot/dts/artpec6-devboard.dts
@@ -1,10 +1,5 @@
-/*
- * Axis ARTPEC-6 development board.
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2.  This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
- */
+// SPDX-License-Identifier: GPL-2.0-only
+// Axis ARTPEC-6 development board.
 
 /dts-v1/;
 #include "artpec6.dtsi"
diff --git a/arch/arm/boot/dts/aspeed-ast2500-evb.dts b/arch/arm/boot/dts/aspeed-ast2500-evb.dts
index 1d24b394ea4c..a497dd135491 100644
--- a/arch/arm/boot/dts/aspeed-ast2500-evb.dts
+++ b/arch/arm/boot/dts/aspeed-ast2500-evb.dts
@@ -5,7 +5,7 @@
 
 / {
 	model = "AST2500 EVB";
-	compatible = "aspeed,ast2500";
+	compatible = "aspeed,ast2500-evb", "aspeed,ast2500";
 
 	aliases {
 		serial4 = &uart5;
diff --git a/arch/arm/boot/dts/aspeed-ast2600-evb-a1.dts b/arch/arm/boot/dts/aspeed-ast2600-evb-a1.dts
index dd7148060c4a..f34a2b1ec2f0 100644
--- a/arch/arm/boot/dts/aspeed-ast2600-evb-a1.dts
+++ b/arch/arm/boot/dts/aspeed-ast2600-evb-a1.dts
@@ -5,6 +5,7 @@
 
 / {
 	model = "AST2600 A1 EVB";
+	compatible = "aspeed,ast2600-evb-a1", "aspeed,ast2600-evb", "aspeed,ast2600";
 
 	/delete-node/regulator-vcc-sdhci0;
 	/delete-node/regulator-vcc-sdhci1;
diff --git a/arch/arm/boot/dts/aspeed-ast2600-evb.dts b/arch/arm/boot/dts/aspeed-ast2600-evb.dts
index b7eb552640cb..de83c0eb1d6e 100644
--- a/arch/arm/boot/dts/aspeed-ast2600-evb.dts
+++ b/arch/arm/boot/dts/aspeed-ast2600-evb.dts
@@ -8,7 +8,7 @@
 
 / {
 	model = "AST2600 EVB";
-	compatible = "aspeed,ast2600";
+	compatible = "aspeed,ast2600-evb", "aspeed,ast2600";
 
 	aliases {
 		serial4 = &uart5;
@@ -23,6 +23,26 @@
 		reg = <0x80000000 0x80000000>;
 	};
 
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		video_engine_memory: video {
+			size = <0x04000000>;
+			alignment = <0x01000000>;
+			compatible = "shared-dma-pool";
+			reusable;
+		};
+
+		gfx_memory: framebuffer {
+			size = <0x01000000>;
+			alignment = <0x01000000>;
+			compatible = "shared-dma-pool";
+			reusable;
+		};
+	};
+
 	vcc_sdhci0: regulator-vcc-sdhci0 {
 		compatible = "regulator-fixed";
 		regulator-name = "SDHCI0 Vcc";
@@ -103,7 +123,7 @@
 &mac0 {
 	status = "okay";
 
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-rxid";
 	phy-handle = <&ethphy0>;
 
 	pinctrl-names = "default";
@@ -114,7 +134,7 @@
 &mac1 {
 	status = "okay";
 
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-rxid";
 	phy-handle = <&ethphy1>;
 
 	pinctrl-names = "default";
@@ -162,6 +182,7 @@
 		status = "okay";
 		m25p,fast-read;
 		label = "bmc";
+		spi-rx-bus-width = <4>;
 		spi-max-frequency = <50000000>;
 #include "openbmc-flash-layout-64.dtsi"
 	};
@@ -176,6 +197,7 @@
 		status = "okay";
 		m25p,fast-read;
 		label = "pnor";
+		spi-rx-bus-width = <4>;
 		spi-max-frequency = <100000000>;
 	};
 };
@@ -187,11 +209,6 @@
 
 &i2c0 {
 	status = "okay";
-
-	temp@2e {
-		compatible = "adi,adt7490";
-		reg = <0x2e>;
-	};
 };
 
 &i2c1 {
@@ -220,10 +237,26 @@
 
 &i2c7 {
 	status = "okay";
+
+	temp@2e {
+		compatible = "adi,adt7490";
+		reg = <0x2e>;
+	};
+
+	eeprom@50 {
+		compatible = "atmel,24c08";
+		reg = <0x50>;
+		pagesize = <16>;
+	};
 };
 
 &i2c8 {
 	status = "okay";
+
+	lm75@4d {
+		compatible = "national,lm75";
+		reg = <0x4d>;
+	};
 };
 
 &i2c9 {
@@ -300,3 +333,18 @@
 	vqmmc-supply = <&vccq_sdhci1>;
 	clk-phase-sd-hs = <7>, <200>;
 };
+
+&vhub {
+	status = "okay";
+	pinctrl-names = "default";
+};
+
+&video {
+	status = "okay";
+	memory-region = <&video_engine_memory>;
+};
+
+&gfx {
+	status = "okay";
+	memory-region = <&gfx_memory>;
+};
diff --git a/arch/arm/boot/dts/aspeed-bmc-amd-daytonax.dts b/arch/arm/boot/dts/aspeed-bmc-amd-daytonax.dts
new file mode 100644
index 000000000000..64bb9bf92de2
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed-bmc-amd-daytonax.dts
@@ -0,0 +1,319 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include "aspeed-g5.dtsi"
+#include <dt-bindings/gpio/aspeed-gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	model = "AMD DaytonaX BMC";
+	compatible = "amd,daytonax-bmc", "aspeed,ast2500";
+
+	memory@80000000 {
+		reg = <0x80000000 0x20000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		video_engine_memory: jpegbuffer {
+			size = <0x02000000>;	/* 32M */
+			alignment = <0x01000000>;
+			compatible = "shared-dma-pool";
+			reusable;
+		};
+	};
+
+	aliases {
+		serial0 = &uart1;
+		serial4 = &uart5;
+	};
+
+	chosen {
+		stdout-path = &uart5;
+		bootargs = "console=ttyS4,115200";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-fault {
+			gpios = <&gpio ASPEED_GPIO(A, 2) GPIO_ACTIVE_LOW>;
+		};
+
+		led-identify {
+			gpios = <&gpio ASPEED_GPIO(A, 3) GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc 0>, <&adc 1>, <&adc 2>, <&adc 3>, <&adc 4>,
+			<&adc 5>, <&adc 6>, <&adc 7>, <&adc 8>, <&adc 9>,
+			<&adc 10>, <&adc 11>, <&adc 12>, <&adc 13>, <&adc 14>,
+			<&adc 15>;
+	};
+};
+
+&fmc {
+	status = "okay";
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "bmc";
+		#include "openbmc-flash-layout.dtsi"
+	};
+};
+
+&mac0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rgmii1_default &pinctrl_mdio1_default>;
+};
+
+&uart1 {
+	//Host Console
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_txd1_default
+		&pinctrl_rxd1_default
+		&pinctrl_nrts1_default
+		&pinctrl_ndtr1_default
+		&pinctrl_ndsr1_default
+		&pinctrl_ncts1_default
+		&pinctrl_ndcd1_default
+		&pinctrl_nri1_default>;
+};
+
+&uart5 {
+	//BMC Console
+	status = "okay";
+};
+
+&vuart {
+	status = "okay";
+	aspeed,lpc-io-reg = <0x3f8>;
+	aspeed,lpc-interrupts = <4 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&adc {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc0_default
+		&pinctrl_adc1_default
+		&pinctrl_adc2_default
+		&pinctrl_adc3_default
+		&pinctrl_adc4_default
+		&pinctrl_adc5_default
+		&pinctrl_adc6_default
+		&pinctrl_adc7_default
+		&pinctrl_adc8_default
+		&pinctrl_adc9_default
+		&pinctrl_adc10_default
+		&pinctrl_adc11_default
+		&pinctrl_adc12_default
+		&pinctrl_adc13_default
+		&pinctrl_adc14_default
+		&pinctrl_adc15_default>;
+};
+
+&gpio {
+	status = "okay";
+	gpio-line-names =
+	/*A0-A7*/	"","","led-fault","led-identify","","","","",
+	/*B0-B7*/	"","","","","","","","",
+	/*C0-C7*/	"id-button","","","","","","","",
+	/*D0-D7*/	"","","ASSERT_BMC_READY","","","","","",
+	/*E0-E7*/	"reset-button","reset-control","power-button","power-control","",
+			"power-good","power-ok","",
+	/*F0-F7*/	"","","","","","","BATTERY_DETECT","",
+	/*G0-G7*/	"","","","","","","","",
+	/*H0-H7*/	"","","","","","","","",
+	/*I0-I7*/	"","","","","","","","",
+	/*J0-J7*/	"","","","","","","","",
+	/*K0-K7*/	"","","","","","","","",
+	/*L0-L7*/	"","","","","","","","",
+	/*M0-M7*/	"","","","","","","","",
+	/*N0-N7*/	"","","","","","","","",
+	/*O0-O7*/	"","","","","","","","",
+	/*P0-P7*/	"","","","","","","","",
+	/*Q0-Q7*/	"","","","","","","","",
+	/*R0-R7*/	"","","","","","","","",
+	/*S0-S7*/	"","","","","","","","",
+	/*T0-T7*/	"","","","","","","","",
+	/*U0-U7*/	"","","","","","","","",
+	/*V0-V7*/	"","","","","","","","",
+	/*W0-W7*/	"","","","","","","","",
+	/*X0-X7*/	"","","","","","","","",
+	/*Y0-Y7*/	"","","","","","","","",
+	/*Z0-Z7*/	"","","","","","","","",
+	/*AA0-AA7*/	"","","","","","","","",
+	/*AB0-AB7*/	"FM_BMC_READ_SPD_TEMP","","","","","","","",
+	/*AC0-AC7*/	"","","","","","","","";
+};
+
+&i2c0 {
+	status = "okay";
+};
+
+&i2c1 {
+	status = "okay";
+};
+
+&i2c2 {
+	status = "okay";
+};
+
+&i2c3 {
+	status = "okay";
+};
+
+&i2c4 {
+	status = "okay";
+};
+
+&i2c5 {
+	status = "okay";
+};
+
+&i2c6 {
+	status = "okay";
+};
+
+&i2c7 {
+	status = "okay";
+};
+
+&i2c8 {
+	status = "okay";
+};
+
+&i2c10 {
+	status = "okay";
+};
+
+&i2c11 {
+	status = "okay";
+};
+
+&i2c12 {
+	status = "okay";
+};
+
+&kcs3 {
+	status = "okay";
+	aspeed,lpc-io-reg = <0xca2>;
+};
+
+&lpc_snoop {
+	status = "okay";
+	snoop-ports = <0x80>, <0x81>;
+};
+
+&lpc_ctrl {
+	status = "okay";
+};
+
+&pwm_tacho {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm0_default
+		&pinctrl_pwm1_default
+		&pinctrl_pwm2_default
+		&pinctrl_pwm3_default
+		&pinctrl_pwm4_default
+		&pinctrl_pwm5_default
+		&pinctrl_pwm6_default
+		&pinctrl_pwm7_default>;
+
+	fan@0 {
+		reg = <0x00>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x00>;
+	};
+
+	fan@1 {
+		reg = <0x00>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x01>;
+	};
+
+	fan@2 {
+		reg = <0x01>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x02>;
+	};
+
+	fan@3 {
+		reg = <0x01>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x03>;
+	};
+
+	fan@4 {
+		reg = <0x02>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x04>;
+	};
+
+	fan@5 {
+		reg = <0x02>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x05>;
+	};
+
+	fan@6 {
+		reg = <0x03>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x06>;
+	};
+
+	fan@7 {
+		reg = <0x03>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x07>;
+	};
+
+	fan@8 {
+		reg = <0x04>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x08>;
+	};
+
+	fan@9 {
+		reg = <0x04>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x09>;
+	};
+
+	fan@10 {
+		reg = <0x05>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x0a>;
+	};
+
+	fan@11 {
+		reg = <0x05>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x0b>;
+	};
+
+	fan@12 {
+		reg = <0x06>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x0c>;
+	};
+
+	fan@13 {
+		reg = <0x06>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x0d>;
+	};
+
+	fan@14 {
+		reg = <0x07>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x0e>;
+	};
+
+	fan@15 {
+		reg = <0x07>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x0f>;
+	};
+};
+
+&video {
+	status = "okay";
+	memory-region = <&video_engine_memory>;
+};
+
+&vhub {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/aspeed-bmc-ampere-mtjade.dts b/arch/arm/boot/dts/aspeed-bmc-ampere-mtjade.dts
index 3515d55bd312..d127cbcc7998 100644
--- a/arch/arm/boot/dts/aspeed-bmc-ampere-mtjade.dts
+++ b/arch/arm/boot/dts/aspeed-bmc-ampere-mtjade.dts
@@ -7,6 +7,50 @@
 	model = "Ampere Mt. Jade BMC";
 	compatible = "ampere,mtjade-bmc", "aspeed,ast2500";
 
+	aliases {
+		/*
+		 *  i2c bus 50-57 assigned to NVMe slot 0-7
+		 */
+		i2c50 = &nvmeslot_0;
+		i2c51 = &nvmeslot_1;
+		i2c52 = &nvmeslot_2;
+		i2c53 = &nvmeslot_3;
+		i2c54 = &nvmeslot_4;
+		i2c55 = &nvmeslot_5;
+		i2c56 = &nvmeslot_6;
+		i2c57 = &nvmeslot_7;
+
+		/*
+		 *  i2c bus 60-67 assigned to NVMe slot 8-15
+		 */
+		i2c60 = &nvmeslot_8;
+		i2c61 = &nvmeslot_9;
+		i2c62 = &nvmeslot_10;
+		i2c63 = &nvmeslot_11;
+		i2c64 = &nvmeslot_12;
+		i2c65 = &nvmeslot_13;
+		i2c66 = &nvmeslot_14;
+		i2c67 = &nvmeslot_15;
+
+		/*
+		 *  i2c bus 70-77 assigned to NVMe slot 16-23
+		 */
+		i2c70 = &nvmeslot_16;
+		i2c71 = &nvmeslot_17;
+		i2c72 = &nvmeslot_18;
+		i2c73 = &nvmeslot_19;
+		i2c74 = &nvmeslot_20;
+		i2c75 = &nvmeslot_21;
+		i2c76 = &nvmeslot_22;
+		i2c77 = &nvmeslot_23;
+
+		/*
+		 *  i2c bus 80-81 assigned to NVMe M2 slot 0-1
+		 */
+		i2c80 = &nvme_m2_0;
+		i2c81 = &nvme_m2_1;
+	};
+
 	chosen {
 		stdout-path = &uart5;
 		bootargs = "console=ttyS4,115200 earlycon";
@@ -53,101 +97,6 @@
 		};
 	};
 
-	gpio-keys {
-		compatible = "gpio-keys";
-
-		shutdown_ack {
-			label = "SHUTDOWN_ACK";
-			gpios = <&gpio ASPEED_GPIO(G, 2) GPIO_ACTIVE_LOW>;
-			linux,code = <ASPEED_GPIO(G, 2)>;
-		};
-
-		reboot_ack {
-			label = "REBOOT_ACK";
-			gpios = <&gpio ASPEED_GPIO(J, 3) GPIO_ACTIVE_LOW>;
-			linux,code = <ASPEED_GPIO(J, 3)>;
-		};
-
-		S0_overtemp {
-			label = "S0_OVERTEMP";
-			gpios = <&gpio ASPEED_GPIO(G, 3) GPIO_ACTIVE_LOW>;
-			linux,code = <ASPEED_GPIO(G, 3)>;
-		};
-
-		S0_hightemp {
-			label = "S0_HIGHTEMP";
-			gpios = <&gpio ASPEED_GPIO(J, 0) GPIO_ACTIVE_LOW>;
-			linux,code = <ASPEED_GPIO(J, 0)>;
-		};
-
-		S0_cpu_fault {
-			label = "S0_CPU_FAULT";
-			gpios = <&gpio ASPEED_GPIO(J, 1) GPIO_ACTIVE_HIGH>;
-			linux,code = <ASPEED_GPIO(J, 1)>;
-		};
-
-		S0_scp_auth_fail {
-			label = "S0_SCP_AUTH_FAIL";
-			gpios = <&gpio ASPEED_GPIO(J, 2) GPIO_ACTIVE_LOW>;
-			linux,code = <ASPEED_GPIO(J, 2)>;
-		};
-
-		S1_scp_auth_fail {
-			label = "S1_SCP_AUTH_FAIL";
-			gpios = <&gpio ASPEED_GPIO(Z, 5) GPIO_ACTIVE_LOW>;
-			linux,code = <ASPEED_GPIO(Z, 5)>;
-		};
-
-		S1_overtemp {
-			label = "S1_OVERTEMP";
-			gpios = <&gpio ASPEED_GPIO(Z, 6) GPIO_ACTIVE_LOW>;
-			linux,code = <ASPEED_GPIO(Z, 6)>;
-		};
-
-		S1_hightemp {
-			label = "S1_HIGHTEMP";
-			gpios = <&gpio ASPEED_GPIO(AB, 0) GPIO_ACTIVE_LOW>;
-			linux,code = <ASPEED_GPIO(AB, 0)>;
-		};
-
-		S1_cpu_fault {
-			label = "S1_CPU_FAULT";
-			gpios = <&gpio ASPEED_GPIO(Z, 1) GPIO_ACTIVE_HIGH>;
-			linux,code = <ASPEED_GPIO(Z, 1)>;
-		};
-
-		id_button {
-			label = "ID_BUTTON";
-			gpios = <&gpio ASPEED_GPIO(Q, 5) GPIO_ACTIVE_LOW>;
-			linux,code = <ASPEED_GPIO(Q, 5)>;
-		};
-
-		psu1_vin_good {
-			label = "PSU1_VIN_GOOD";
-			gpios = <&gpio ASPEED_GPIO(H, 4) GPIO_ACTIVE_LOW>;
-			linux,code = <ASPEED_GPIO(H, 4)>;
-		};
-
-		psu2_vin_good {
-			label = "PSU2_VIN_GOOD";
-			gpios = <&gpio ASPEED_GPIO(H, 5) GPIO_ACTIVE_LOW>;
-			linux,code = <ASPEED_GPIO(H, 5)>;
-		};
-
-		psu1_present {
-			label = "PSU1_PRESENT";
-			gpios = <&gpio ASPEED_GPIO(I, 0) GPIO_ACTIVE_LOW>;
-			linux,code = <ASPEED_GPIO(I, 0)>;
-		};
-
-		psu2_present {
-			label = "PSU2_PRESENT";
-			gpios = <&gpio ASPEED_GPIO(I, 1) GPIO_ACTIVE_LOW>;
-			linux,code = <ASPEED_GPIO(I, 1)>;
-		};
-
-	};
-
 	gpioA0mux: mux-controller {
 		compatible = "gpio-mux";
 		#mux-control-cells = <0>;
@@ -295,17 +244,8 @@
 			<&adc10mux 0>, <&adc10mux 1>,
 			<&adc11mux 0>, <&adc11mux 1>,
 			<&adc12mux 0>, <&adc12mux 1>,
-			<&adc13mux 0>, <&adc13mux 1>;
-	};
-
-	iio-hwmon-adc14 {
-		compatible = "iio-hwmon";
-		io-channels = <&adc 14>;
-	};
-
-	iio-hwmon-battery {
-		compatible = "iio-hwmon";
-		io-channels = <&adc 15>;
+			<&adc13mux 0>, <&adc13mux 1>,
+			<&adc 14>, <&adc 15>;
 	};
 };
 
@@ -318,6 +258,13 @@
 		/* spi-max-frequency = <50000000>; */
 #include "openbmc-flash-layout-64.dtsi"
 	};
+
+	flash@1 {
+		status = "okay";
+		m25p,fast-read;
+		label = "alt-bmc";
+#include "openbmc-flash-layout-64-alt.dtsi"
+	};
 };
 
 &spi1 {
@@ -330,6 +277,15 @@
 		m25p,fast-read;
 		label = "pnor";
 		/* spi-max-frequency = <100000000>; */
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			uefi@400000 {
+				reg = <0x400000 0x1C00000>;
+				label = "pnor-uefi";
+			};
+		};
 	};
 };
 
@@ -445,6 +401,220 @@
 
 &i2c5 {
 	status = "okay";
+	i2c-mux@70 {
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x70>;
+		i2c-mux-idle-disconnect;
+
+		nvmeslot_0_7: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x3>;
+		};
+	};
+
+	i2c-mux@71 {
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x71>;
+		i2c-mux-idle-disconnect;
+
+		nvmeslot_8_15: i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x4>;
+		};
+
+		nvmeslot_16_23: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x3>;
+		};
+
+	};
+
+	i2c-mux@72 {
+		compatible = "nxp,pca9545";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x72>;
+		i2c-mux-idle-disconnect;
+
+		nvme_m2_0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x0>;
+		};
+
+		nvme_m2_1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x1>;
+		};
+	};
+};
+
+&nvmeslot_0_7 {
+	status = "okay";
+
+	i2c-mux@75 {
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x75>;
+		i2c-mux-idle-disconnect;
+
+		nvmeslot_0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x0>;
+		};
+		nvmeslot_1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x1>;
+		};
+		nvmeslot_2: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x2>;
+		};
+		nvmeslot_3: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x3>;
+		};
+		nvmeslot_4: i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x4>;
+		};
+		nvmeslot_5: i2c@5 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x5>;
+		};
+		nvmeslot_6: i2c@6 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x6>;
+		};
+		nvmeslot_7: i2c@7 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x7>;
+		};
+
+	};
+};
+
+&nvmeslot_8_15 {
+	status = "okay";
+
+	i2c-mux@75 {
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x75>;
+		i2c-mux-idle-disconnect;
+
+		nvmeslot_8: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x0>;
+		};
+		nvmeslot_9: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x1>;
+		};
+		nvmeslot_10: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x2>;
+		};
+		nvmeslot_11: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x3>;
+		};
+		nvmeslot_12: i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x4>;
+		};
+		nvmeslot_13: i2c@5 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x5>;
+		};
+		nvmeslot_14: i2c@6 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x6>;
+		};
+		nvmeslot_15: i2c@7 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x7>;
+		};
+	};
+};
+
+&nvmeslot_16_23 {
+	status = "okay";
+
+	i2c-mux@75 {
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x75>;
+		i2c-mux-idle-disconnect;
+
+		nvmeslot_16: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x0>;
+		};
+		nvmeslot_17: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x1>;
+		};
+		nvmeslot_18: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x2>;
+		};
+		nvmeslot_19: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x3>;
+		};
+		nvmeslot_20: i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x4>;
+		};
+		nvmeslot_21: i2c@5 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x5>;
+		};
+		nvmeslot_22: i2c@6 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x6>;
+		};
+		nvmeslot_23: i2c@7 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x7>;
+		};
+	};
 };
 
 &i2c6 {
@@ -586,7 +756,7 @@
 	/*E0-E7*/	"","","","","","","","",
 	/*F0-F7*/	"","","BMC_SYS_PSON_L","S0_DDR_SAVE","PGOOD",
 			"S1_DDR_SAVE","","",
-	/*G0-G7*/	"S0_FW_BOOT_OK","SHD_REQ_L","","S0_OVERTEMP_L","","",
+	/*G0-G7*/	"host0-ready","SHD_REQ_L","","S0_OVERTEMP_L","","",
 			"","",
 	/*H0-H7*/	"","","","","PSU1_VIN_GOOD","PSU2_VIN_GOOD","","",
 	/*I0-I7*/	"PSU1_PRESENT","PSU2_PRESENT","S1_BMC_SPECIAL_BOOT",
@@ -602,7 +772,7 @@
 	/*Q0-Q7*/	"","","","","","UID_BUTTON","","",
 	/*R0-R7*/	"","","BMC_EXT_HIGHTEMP_L","OCP_AUX_PWREN",
 			"OCP_MAIN_PWREN","RESET_BUTTON","","",
-	/*S0-S7*/	"","","","","RTC_BAT_SEN_EN","","","",
+	/*S0-S7*/	"","","","","rtc-battery-voltage-read-enable","","","",
 	/*T0-T7*/	"","","","","","","","",
 	/*U0-U7*/	"","","","","","","","",
 	/*V0-V7*/	"","","","","","","","",
@@ -617,7 +787,7 @@
 	/*AC0-AC7*/	"SYS_PWR_GD","","","","","BMC_READY","SLAVE_PRESENT_L",
 			"BMC_OCP_PG";
 
-	i2c4_o_en {
+	i2c4-o-en-hog {
 		gpio-hog;
 		gpios = <ASPEED_GPIO(Y, 2) GPIO_ACTIVE_HIGH>;
 		output-high;
diff --git a/arch/arm/boot/dts/aspeed-bmc-ampere-mtmitchell.dts b/arch/arm/boot/dts/aspeed-bmc-ampere-mtmitchell.dts
new file mode 100644
index 000000000000..606cd4be245a
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed-bmc-ampere-mtmitchell.dts
@@ -0,0 +1,546 @@
+// SPDX-License-Identifier: GPL-2.0-only
+// Copyright (c) 2022, Ampere Computing LLC
+
+/dts-v1/;
+
+#include "aspeed-g6.dtsi"
+#include <dt-bindings/gpio/aspeed-gpio.h>
+
+/ {
+	model = "Ampere Mt.Mitchell BMC";
+	compatible = "ampere,mtmitchell-bmc", "aspeed,ast2600";
+
+	chosen {
+		stdout-path = &uart5;
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x80000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		gfx_memory: framebuffer {
+			size = <0x01000000>;
+			alignment = <0x01000000>;
+			compatible = "shared-dma-pool";
+			reusable;
+		};
+
+		video_engine_memory: video {
+			size = <0x04000000>;
+			alignment = <0x01000000>;
+			compatible = "shared-dma-pool";
+			reusable;
+		};
+
+		vga_memory: region@bf000000 {
+			no-map;
+			compatible = "shared-dma-pool";
+			reg = <0xbf000000 0x01000000>;  /* 16M */
+		};
+	};
+
+	voltage_mon_reg: voltage-mon-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "ltc2497_reg";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	gpioI5mux: mux-controller {
+		compatible = "gpio-mux";
+		#mux-control-cells = <0>;
+		mux-gpios = <&gpio0 ASPEED_GPIO(I, 5) GPIO_ACTIVE_HIGH>;
+	};
+
+	adc0mux: adc0mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc0 0>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		channels = "s0", "s1";
+	};
+
+	adc1mux: adc1mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc0 1>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		channels = "s0", "s1";
+	};
+
+	adc2mux: adc2mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc0 2>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		channels = "s0", "s1";
+	};
+
+	adc3mux: adc3mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc0 3>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		channels = "s0", "s1";
+	};
+
+	adc4mux: adc4mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc0 4>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		channels = "s0", "s1";
+	};
+
+	adc5mux: adc5mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc0 5>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		channels = "s0", "s1";
+	};
+
+	adc6mux: adc6mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc0 6>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		channels = "s0", "s1";
+	};
+
+	adc7mux: adc7mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc0 7>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		channels = "s0", "s1";
+	};
+
+	adc8mux: adc8mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc1 0>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		channels = "s0", "s1";
+	};
+
+	adc9mux: adc9mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc1 1>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		channels = "s0", "s1";
+	};
+
+	adc10mux: adc10mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc1 2>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		channels = "s0", "s1";
+	};
+
+	adc11mux: adc11mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc1 3>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		channels = "s0", "s1";
+	};
+
+	adc12mux: adc12mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc1 4>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		channels = "s0", "s1";
+	};
+
+	adc13mux: adc13mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc1 5>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		channels = "s0", "s1";
+	};
+
+	adc14mux: adc14mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc1 6>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		channels = "s0", "s1";
+	};
+
+	adc15mux: adc15mux {
+		compatible = "io-channel-mux";
+		io-channels = <&adc1 7>;
+		#io-channel-cells = <1>;
+		io-channel-names = "parent";
+		mux-controls = <&gpioI5mux>;
+		channels = "s0", "s1";
+	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc0mux 0>, <&adc0mux 1>,
+			<&adc1mux 0>, <&adc1mux 1>,
+			<&adc2mux 0>, <&adc2mux 1>,
+			<&adc3mux 0>, <&adc3mux 1>,
+			<&adc4mux 0>, <&adc4mux 1>,
+			<&adc5mux 0>, <&adc5mux 1>,
+			<&adc6mux 0>, <&adc6mux 1>,
+			<&adc7mux 0>, <&adc7mux 1>,
+			<&adc8mux 0>, <&adc8mux 1>,
+			<&adc9mux 0>, <&adc9mux 1>,
+			<&adc10mux 0>, <&adc10mux 1>,
+			<&adc11mux 0>, <&adc11mux 1>,
+			<&adc12mux 0>, <&adc12mux 1>,
+			<&adc13mux 0>, <&adc13mux 1>,
+			<&adc14mux 0>, <&adc14mux 1>,
+			<&adc15mux 0>, <&adc15mux 1>,
+			<&adc_i2c 0>, <&adc_i2c 1>,
+			<&adc_i2c 2>, <&adc_i2c 3>,
+			<&adc_i2c 4>, <&adc_i2c 5>,
+			<&adc_i2c 6>, <&adc_i2c 7>,
+			<&adc_i2c 8>, <&adc_i2c 9>,
+			<&adc_i2c 10>, <&adc_i2c 11>,
+			<&adc_i2c 12>, <&adc_i2c 13>,
+			<&adc_i2c 14>, <&adc_i2c 15>;
+	};
+};
+
+&mdio0 {
+	status = "okay";
+
+	ethphy0: ethernet-phy@0 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0>;
+	};
+};
+
+&mac0 {
+	status = "okay";
+
+	phy-mode = "rgmii";
+	phy-handle = <&ethphy0>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rgmii1_default>;
+};
+
+&fmc {
+	status = "okay";
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "bmc";
+		spi-max-frequency = <50000000>;
+#include "openbmc-flash-layout-64.dtsi"
+	};
+
+	flash@1 {
+		status = "okay";
+		m25p,fast-read;
+		label = "alt-bmc";
+		spi-max-frequency = <50000000>;
+#include "openbmc-flash-layout-64-alt.dtsi"
+	};
+};
+
+&spi1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_spi1_default>;
+
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "pnor";
+		spi-max-frequency = <20000000>;
+	};
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&uart3 {
+	status = "okay";
+};
+
+&uart4 {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	temperature-sensor@2e {
+		compatible = "adi,adt7490";
+		reg = <0x2e>;
+	};
+};
+
+&i2c1 {
+	status = "okay";
+};
+
+&i2c2 {
+	status = "okay";
+
+	psu@58 {
+		compatible = "pmbus";
+		reg = <0x58>;
+	};
+
+	psu@59 {
+		compatible = "pmbus";
+		reg = <0x59>;
+	};
+};
+
+&i2c3 {
+	status = "okay";
+};
+
+&i2c4 {
+	status = "okay";
+
+	adc_i2c: adc@16 {
+		compatible = "lltc,ltc2497";
+		reg = <0x16>;
+		vref-supply = <&voltage_mon_reg>;
+		#io-channel-cells = <1>;
+	 };
+
+	eeprom@50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+		pagesize = <32>;
+	};
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9545";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x70>;
+		i2c-mux-idle-disconnect;
+
+		i2c4_bus70_chn0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x0>;
+
+			outlet_temp1: temperature-sensor@48 {
+				compatible = "ti,tmp75";
+				reg = <0x48>;
+			};
+			psu1_inlet_temp2: temperature-sensor@49 {
+				compatible = "ti,tmp75";
+				reg = <0x49>;
+			};
+		};
+
+		i2c4_bus70_chn1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x1>;
+
+			pcie_zone_temp1: temperature-sensor@48 {
+				compatible = "ti,tmp75";
+				reg = <0x48>;
+			};
+			psu0_inlet_temp2: temperature-sensor@49 {
+				compatible = "ti,tmp75";
+				reg = <0x49>;
+			};
+		};
+
+		i2c4_bus70_chn2: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x2>;
+
+			pcie_zone_temp2: temperature-sensor@48 {
+				compatible = "ti,tmp75";
+				reg = <0x48>;
+			};
+			outlet_temp2: temperature-sensor@49 {
+				compatible = "ti,tmp75";
+				reg = <0x49>;
+			};
+		};
+
+		i2c4_bus70_chn3: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x3>;
+
+			mb_inlet_temp1: temperature-sensor@7c {
+				compatible = "microchip,emc1413";
+				reg = <0x7c>;
+			};
+			mb_inlet_temp2: temperature-sensor@4c {
+				compatible = "microchip,emc1413";
+				reg = <0x4c>;
+			};
+		};
+	};
+};
+
+&i2c5 {
+	status = "okay";
+
+	i2c-mux@70 {
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x70>;
+		i2c-mux-idle-disconnect;
+	};
+};
+
+&i2c6 {
+	status = "okay";
+	rtc@51 {
+		compatible = "nxp,pcf85063a";
+		reg = <0x51>;
+	};
+};
+
+&i2c7 {
+	status = "okay";
+};
+
+&i2c9 {
+	status = "okay";
+};
+
+&i2c11 {
+	status = "okay";
+};
+
+&i2c14 {
+	status = "okay";
+	eeprom@50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+		pagesize = <32>;
+	};
+
+	bmc_ast2600_cpu: temperature-sensor@35 {
+		compatible = "ti,tmp175";
+		reg = <0x35>;
+	};
+};
+
+&adc0 {
+	ref_voltage = <2500>;
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc0_default &pinctrl_adc1_default
+		&pinctrl_adc2_default &pinctrl_adc3_default
+		&pinctrl_adc4_default &pinctrl_adc5_default
+		&pinctrl_adc6_default &pinctrl_adc7_default>;
+};
+
+&adc1 {
+	ref_voltage = <2500>;
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc8_default &pinctrl_adc9_default
+		&pinctrl_adc10_default &pinctrl_adc11_default
+		&pinctrl_adc12_default &pinctrl_adc13_default
+		&pinctrl_adc14_default &pinctrl_adc15_default>;
+};
+
+&vhub {
+	status = "okay";
+};
+
+&video {
+	status = "okay";
+	memory-region = <&video_engine_memory>;
+};
+
+&gpio0 {
+	gpio-line-names =
+	/*A0-A7*/	"","","","","","i2c2-reset-n","i2c6-reset-n","i2c4-reset-n",
+	/*B0-B7*/	"","","","","host0-sysreset-n","host0-pmin-n","","",
+	/*C0-C7*/	"s0-vrd-fault-n","s1-vrd-fault-n","","",
+			"irq-n","","vrd-sel","spd-sel",
+	/*D0-D7*/	"presence-ps0","presence-ps1","hsc-12vmain-alt2-n","ext-high-temp-n",
+			"","bmc-ncsi-txen","","",
+	/*E0-E7*/	"","","clk50m-bmc-ncsi","","","","","",
+	/*F0-F7*/	"s0-pcp-oc-warn-n","s1-pcp-oc-warn-n","power-chassis-control",
+			"cpu-bios-recover","s0-heartbeat","hs-csout-prochot",
+			"s0-vr-hot-n","s1-vr-hot-n",
+	/*G0-G7*/	"","","hsc-12vmain-alt1-n","","","","","",
+	/*H0-H7*/	"","","wd-disable-n","power-chassis-good","","","","",
+	/*I0-I7*/	"","","","","","adc-sw","power-button","rtc-battery-voltage-read-enable",
+	/*J0-J7*/	"","","","","","","","",
+	/*K0-K7*/	"","","","","","","","",
+	/*L0-L7*/	"","","","","","","","",
+	/*M0-M7*/	"","s0-ddr-save","soc-spi-nor-access","presence-cpu0",
+			"s0-rtc-lock","","","",
+	/*N0-N7*/	"hpm-fw-recovery","hpm-stby-rst-n","jtag-sel-s0","led-sw-hb",
+			"jtag-dbgr-prsnt-n","s1-heartbeat","","",
+	/*O0-O7*/	"","","","","","","","",
+	/*P0-P7*/	"ps0-ac-loss-n","ps1-ac-loss-n","","",
+			"led-fault","cpld-user-mode","jtag-srst-n","led-bmc-hb",
+	/*Q0-Q7*/	"","","","","","","","",
+	/*R0-R7*/	"","","","","","","","",
+	/*S0-S7*/	"","","identify-button","led-identify",
+			"s1-ddr-save","spi-nor-access","sys-pgood","presence-cpu1",
+	/*T0-T7*/	"","","","","","","","",
+	/*U0-U7*/	"","","","","","","","",
+	/*V0-V7*/	"s0-hightemp-n","s0-fault-alert","s0-sys-auth-failure-n",
+			"host0-reboot-ack-n","host0-ready","host0-shd-req-n",
+			"host0-shd-ack-n","s0-overtemp-n",
+	/*W0-W7*/	"ocp-aux-pwren","ocp-main-pwren","ocp-pgood","",
+			"bmc-ok","bmc-ready","spi0-program-sel","spi0-backup-sel",
+	/*X0-X7*/	"i2c-backup-sel","s1-fault-alert","s1-fw-boot-ok",
+			"s1-hightemp-n","s0-spi-auth-fail-n","s1-sys-auth-failure-n",
+			"s1-overtemp-n","s1-spi-auth-fail-n",
+	/*Y0-Y7*/	"","","","","","","","host0-special-boot",
+	/*Z0-Z7*/	"reset-button","ps0-pgood","ps1-pgood","","","","","";
+};
+
+&gpio1 {
+	gpio-line-names =
+	/*18A0-18A7*/	"","","","","","","","",
+	/*18B0-18B7*/	"","","","","","","s0-soc-pgood","",
+	/*18C0-18C7*/	"uart1-mode0","uart1-mode1","uart2-mode0","uart2-mode1",
+			"uart3-mode0","uart3-mode1","uart4-mode0","uart4-mode1",
+	/*18D0-18D7*/	"","","","","","","","",
+	/*18E0-18E3*/	"","","","";
+};
diff --git a/arch/arm/boot/dts/aspeed-bmc-arm-centriq2400-rep.dts b/arch/arm/boot/dts/aspeed-bmc-arm-centriq2400-rep.dts
deleted file mode 100644
index 3395de96ee11..000000000000
--- a/arch/arm/boot/dts/aspeed-bmc-arm-centriq2400-rep.dts
+++ /dev/null
@@ -1,225 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/dts-v1/;
-
-#include "aspeed-g5.dtsi"
-#include <dt-bindings/gpio/aspeed-gpio.h>
-
-/ {
-	model = "Qualcomm Centriq 2400  REP AST2520";
-	compatible = "qualcomm,centriq2400-rep-bmc", "aspeed,ast2500";
-
-	chosen {
-		stdout-path = &uart5;
-		bootargs = "console=ttyS4,115200 earlycon";
-	};
-
-	memory@80000000 {
-		reg = <0x80000000 0x40000000>;
-	};
-
-	iio-hwmon {
-		compatible = "iio-hwmon";
-		io-channels = <&adc 0>, <&adc 1>, <&adc 2>, <&adc 3>,
-                        <&adc 4>, <&adc 5>, <&adc 6>, <&adc 8>;
-	};
-
-	iio-hwmon-battery {
-		compatible = "iio-hwmon";
-		io-channels = <&adc 7>;
-	};
-
-	leds {
-		compatible = "gpio-leds";
-
-		uid_led {
-			label = "UID_LED";
-			gpios = <&gpio ASPEED_GPIO(Q, 5) GPIO_ACTIVE_LOW>;
-		};
-
-		ras_error_led {
-			label = "RAS_ERROR_LED";
-			gpios = <&gpio ASPEED_GPIO(F, 6) GPIO_ACTIVE_LOW>;
-		};
-
-		system_fault {
-			label = "System_fault";
-			gpios = <&gpio ASPEED_GPIO(A, 1) GPIO_ACTIVE_LOW>;
-		};
-	};
-};
-
-&fmc {
-	status = "okay";
-	flash@0 {
-		status = "okay";
-		m25p,fast-read;
-		label = "bmc";
-#include "openbmc-flash-layout.dtsi"
-	};
-};
-
-&spi1 {
-	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_spi1_default>;
-	flash@0 {
-		status = "okay";
-	};
-};
-
-&spi2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_spi2ck_default
-			&pinctrl_spi2miso_default
-			&pinctrl_spi2mosi_default
-			&pinctrl_spi2cs0_default>;
-};
-
-&uart3 {
-	status = "okay";
-
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_txd3_default &pinctrl_rxd3_default>;
-	current-speed = <115200>;
-};
-
-&uart5 {
-	status = "okay";
-};
-
-&mac0 {
-	status = "okay";
-
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_rgmii1_default &pinctrl_mdio1_default>;
-};
-
-&i2c0 {
-	status = "okay";
-};
-
-&i2c1 {
-	status = "okay";
-
-	tmp421@1e {
-		compatible = "ti,tmp421";
-		reg = <0x1e>;
-	};
-	tmp421@2a {
-		compatible = "ti,tmp421";
-		reg = <0x2a>;
-	};
-	tmp421@4e {
-		compatible = "ti,tmp421";
-		reg = <0x4e>;
-	};
-	tmp421@1c {
-		compatible = "ti,tmp421";
-		reg = <0x1c>;
-	};
-};
-
-&i2c2 {
-	status = "okay";
-};
-
-&i2c3 {
-	status = "okay";
-};
-
-&i2c4 {
-	status = "okay";
-};
-
-&i2c5 {
-	status = "okay";
-};
-
-&i2c6 {
-	status = "okay";
-
-	tmp421@1d {
-		compatible = "ti,tmp421";
-		reg = <0x1d>;
-	};
-	tmp421@1f {
-		compatible = "ti,tmp421";
-		reg = <0x1f>;
-	};
-	tmp421@4d {
-		compatible = "ti,tmp421";
-		reg = <0x4d>;
-	};
-	tmp421@4f {
-		compatible = "ti,tmp421";
-		reg = <0x4f>;
-	};
-	nvt210@4c {
-		compatible = "nvt210";
-		reg = <0x4c>;
-	};
-	eeprom@50 {
-		compatible = "atmel,24c128";
-		reg = <0x50>;
-		pagesize = <128>;
-	};
-};
-
-&i2c7 {
-	status = "okay";
-};
-
-&i2c8 {
-	status = "okay";
-
-	pca9641@70 {
-		compatible = "nxp,pca9641";
-		reg = <0x70>;
-		i2c-arb {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			tmp421@1d {
-				compatible = "tmp421";
-				reg = <0x1d>;
-			};
-			adm1278@12 {
-				compatible = "adi,adm1278";
-				reg = <0x12>;
-				Rsense = <500>;
-			};
-			eeprom@50 {
-				compatible = "atmel,24c02";
-				reg = <0x50>;
-			};
-			ds1100@58 {
-				compatible = "ds1100";
-				reg = <0x58>;
-			};
-		};
-	};
-};
-
-&i2c9 {
-	status = "okay";
-};
-
-&vuart {
-	status = "okay";
-};
-
-&gfx {
-	status = "okay";
-};
-
-&pinctrl {
-	aspeed,external-nodes = <&gfx &lhc>;
-};
-
-&gpio {
-	pin_gpio_c7 {
-		gpio-hog;
-		gpios = <ASPEED_GPIO(C, 7) GPIO_ACTIVE_HIGH>;
-		output;
-		line-name = "BIOS_SPI_MUX_S";
-	};
-};
diff --git a/arch/arm/boot/dts/aspeed-bmc-asrock-romed8hm3.dts b/arch/arm/boot/dts/aspeed-bmc-asrock-romed8hm3.dts
new file mode 100644
index 000000000000..ff4c07c69af1
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed-bmc-asrock-romed8hm3.dts
@@ -0,0 +1,261 @@
+// SPDX-License-Identifier: GPL-2.0+
+/dts-v1/;
+
+#include "aspeed-g5.dtsi"
+#include <dt-bindings/gpio/aspeed-gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/{
+	model = "ASRock ROMED8HM3 BMC v1.00";
+	compatible = "asrock,romed8hm3-bmc", "aspeed,ast2500";
+
+	aliases {
+		serial4 = &uart5;
+	};
+
+	chosen {
+		stdout-path = &uart5;
+		bootargs = "console=tty0 console=ttyS4,115200 earlycon";
+	};
+
+	memory@80000000 {
+		reg = <0x80000000 0x20000000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		heartbeat {
+			gpios = <&gpio ASPEED_GPIO(H, 6) GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "timer";
+		};
+
+		system-fault {
+			gpios = <&gpio ASPEED_GPIO(Z, 2) GPIO_ACTIVE_LOW>;
+			panic-indicator;
+		};
+	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc 0>, <&adc 1>, <&adc 2>, <&adc 3>,
+			<&adc 4>, <&adc 5>, <&adc 6>, <&adc 7>,
+			<&adc 8>, <&adc 9>, <&adc 10>, <&adc 11>,
+			<&adc 12>, <&adc 13>, <&adc 14>, <&adc 15>;
+	};
+};
+
+&fmc {
+	status = "okay";
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "bmc";
+		spi-max-frequency = <100000000>; /* 100 MHz */
+#include "openbmc-flash-layout-64.dtsi"
+	};
+};
+
+&uart5 {
+	status = "okay";
+};
+
+&vuart {
+	status = "okay";
+	aspeed,lpc-io-reg = <0x2f8>;
+	aspeed,lpc-interrupts = <3 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&mac0 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rgmii1_default &pinctrl_mdio1_default>;
+};
+
+&i2c0 {
+	status = "okay";
+
+	/* inlet temp sensor */
+	w83773g@4c {
+		compatible = "nuvoton,w83773g";
+		reg = <0x4c>;
+	};
+};
+
+&i2c1 {
+	status = "okay";
+};
+
+&i2c2 {
+	status = "okay";
+
+	/* IPB temp sensor */
+	w83773g@4c {
+		compatible = "nuvoton,w83773g";
+		reg = <0x4c>;
+	};
+
+	/* IPB PMIC */
+	lm25066@40 {
+		compatible = "lm25066";
+		reg = <0x40>;
+		shunt-resistor-micro-ohms = <1000>;
+	};
+
+	/* 12VSB PMIC */
+	lm25066@41 {
+		compatible = "lm25066";
+		reg = <0x41>;
+		shunt-resistor-micro-ohms = <10000>;
+	};
+};
+
+&i2c4 {
+	status = "okay";
+};
+
+&i2c5 {
+	status = "okay";
+};
+
+&i2c6 {
+	status = "okay";
+};
+
+&i2c7 {
+	status = "okay";
+
+	/* Baseboard FRU eeprom */
+	eeprom@50 {
+		compatible = "st,24c128", "atmel,24c128";
+		reg = <0x50>;
+		pagesize = <16>;
+	};
+};
+
+&i2c8 {
+	status = "okay";
+};
+
+&i2c9 {
+	status = "okay";
+};
+
+&video {
+	status = "okay";
+};
+
+&vhub {
+	status = "okay";
+};
+
+&lpc_ctrl {
+	status = "okay";
+};
+
+&lpc_snoop {
+	status = "okay";
+	snoop-ports = <0x80>;
+};
+
+&kcs3 {
+	status = "okay";
+	aspeed,lpc-io-reg = <0xca2>;
+};
+
+&pwm_tacho {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm3_default
+		&pinctrl_pwm4_default
+		&pinctrl_pwm5_default
+		&pinctrl_pwm6_default>;
+
+	fan@3 {
+		reg = <0x03>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x03 0x0b>;
+	};
+
+	fan@4 {
+		reg = <0x04>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x04 0x0c>;
+	};
+
+	fan@5 {
+		reg = <0x05>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x05 0x0d>;
+	};
+
+	fan@6 {
+		reg = <0x06>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x06 0x0e>;
+	};
+};
+
+&gpio {
+	status = "okay";
+	gpio-line-names =
+		/*  A */ "LOCATORLED_STATUS_N", "BMC_MAC2_INTB", "NMI_BTN_N", "BMC_NMI",
+			"", "", "", "",
+		/*  B */ "POST_COMPLETE_N", "", "", "", "", "", "", "",
+		/*  C */ "", "", "", "", "PCIE_HP_SEL_N", "PCIE_SATA_SEL_N", "LOCATORBTN", "",
+		/*  D */ "BMC_PSIN", "BMC_PSOUT", "BMC_RESETCON", "RESETCON",
+			"", "", "", "PSU_FAN_FAIL_N",
+		/*  E */ "", "", "", "", "", "", "", "",
+		/*  F */ "NIC_PWR_GOOD", "PRSNTB0", "PRSNTB1", "PRSNTB2",
+			"PRSNTB3", "", "3VSB_PCIE1_PG", "12V_PCIE1_PG",
+		/*  G */ "HWM_BAT_EN", "CHASSIS_ID0", "CHASSIS_ID1", "CHASSIS_ID2",
+			"BMC_ALERT1_N_R", "BMC_ALERT2_N_R", "BMC_ALERT3_N", "BMC_ALERT4_N",
+		/*  H */ "X24_C1_PRSNT", "X24_C2_PRSNT", "X24_C3_PRSNT", "FM_MEM_THERM_EVENT_BMC_R_N",
+			"FACMODE", "BMC_RTCRST", "BMC_HB_LED_N", "BMC_CASEOPEN",
+		/*  I */ "", "", "", "", "", "", "", "",
+		/*  J */ "BMC_READY", "BMC_PCH_BIOS_CS_N", "", "P0_MA_DDR_QS_CS_N",
+			"", "", "", "",
+		/*  K */ "", "", "", "", "", "", "", "",
+		/*  L */ "", "", "", "", "", "", "", "",
+		/*  M */ "", "", "MEZZ_PWRBRK_N", "OCP_HP_RST_EN",
+			"MAIN_PWR_EN_G", "BMC_MAIN_EN", "AUX_PWR_EN_G", "BMC_AUX_EN",
+		/*  N */ "", "", "", "", "", "", "", "",
+		/*  O */ "", "", "", "", "", "", "", "",
+		/*  P */ "", "", "", "", "", "", "", "",
+		/*  Q */ "", "", "", "",
+			"BMC_SMB_PRESENT_1_N", "BMC_SMB_PRESENT_2_N",
+			"BMC_SMB_PRESENT_3_N", "BMC_PCIE_WAKE_N",
+		/*  R */ "", "", "THERMALTRIP_CLEAR_N", "", "", "", "", "",
+		/*  S */ "", "", "", "", "", "", "", "",
+		/*  T */ "", "", "", "", "", "", "", "",
+		/*  U */ "", "", "", "", "", "", "", "",
+		/*  V */ "", "", "", "", "", "", "", "",
+		/*  W */ "", "", "", "", "", "", "", "",
+		/*  X */ "", "", "", "", "", "", "", "",
+		/*  Y */ "SLP_S3", "SLP_S4_S5", "NODE_ID_1", "NODE_ID_2", "", "", "", "",
+		/*  Z */ "", "", "SYSTEM_FAULT_LED_N", "FAST_THROTTLE_N",
+			"", "", "", "",
+		/* AA */ "FM_CPU0_IBMC_THERMTRIP_N", "", "PROCHOT_L_G", "",
+			"", "", "", "",
+		/* AB */ "BMC_FORCE_SELFREFRESH", "PWRGD_OUT", "", "IRQ_BMC_PCH_SMI_LPC_N",
+			"", "", "", "",
+		/* AC */ "", "", "", "", "", "", "", "";
+};
+
+&adc {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc0_default
+		&pinctrl_adc1_default
+		&pinctrl_adc2_default
+		&pinctrl_adc3_default
+		&pinctrl_adc4_default
+		&pinctrl_adc5_default
+		&pinctrl_adc6_default
+		&pinctrl_adc7_default
+		&pinctrl_adc8_default
+		&pinctrl_adc9_default
+		&pinctrl_adc10_default
+		&pinctrl_adc11_default
+		&pinctrl_adc12_default
+		&pinctrl_adc13_default
+		&pinctrl_adc14_default
+		&pinctrl_adc15_default>;
+};
diff --git a/arch/arm/boot/dts/aspeed-bmc-bytedance-g220a.dts b/arch/arm/boot/dts/aspeed-bmc-bytedance-g220a.dts
index 01dace8f5e5f..f75cad41ae6f 100644
--- a/arch/arm/boot/dts/aspeed-bmc-bytedance-g220a.dts
+++ b/arch/arm/boot/dts/aspeed-bmc-bytedance-g220a.dts
@@ -100,7 +100,7 @@
 
 	gpio-keys {
 		compatible = "gpio-keys";
-		burn-in-signal {
+		event-burn-in-signal {
 			label = "burn-in";
 			gpios = <&gpio ASPEED_GPIO(R, 5) GPIO_ACTIVE_LOW>;
 			linux,code = <ASPEED_GPIO(R, 5)>;
@@ -111,139 +111,139 @@
 		compatible = "gpio-keys-polled";
 		poll-interval = <1000>;
 
-		rear-riser1-presence {
+		event-rear-riser1-presence {
 			label = "rear-riser1-presence";
 			gpios = <&pca0 1 GPIO_ACTIVE_LOW>;
 			linux,code = <1>;
 		};
 
-		alrt-pvddq-cpu0 {
+		event-alrt-pvddq-cpu0 {
 			label = "alrt-pvddq-cpu0";
 			gpios = <&pca0 8 GPIO_ACTIVE_LOW>;
 			linux,code = <2>;
 		};
 
-		rear-riser0-presence {
+		event-rear-riser0-presence {
 			label = "rear-riser0-presence";
 			gpios = <&pca0 9 GPIO_ACTIVE_LOW>;
 			linux,code = <3>;
 		};
 
-		fault-pvddq-cpu0 {
+		event-fault-pvddq-cpu0 {
 			label = "fault-pvddq-cpu0";
 			gpios = <&pca0 10 GPIO_ACTIVE_LOW>;
 			linux,code = <4>;
 		};
 
-		alrt-pvddq-cpu1 {
+		event-alrt-pvddq-cpu1 {
 			label = "alrt-pvddq-cpu1";
 			gpios = <&pca0 11 GPIO_ACTIVE_LOW>;
 			linux,code = <5>;
 		};
 
-		fault-pvddq-cpu1 {
+		event-fault-pvddq-cpu1 {
 			label = "alrt-pvddq-cpu1";
 			gpios = <&pca0 12 GPIO_ACTIVE_LOW>;
 			linux,code = <6>;
 		};
 
-		fault-pvccin-cpu1 {
+		event-fault-pvccin-cpu1 {
 			label = "fault-pvccin-cpuq";
 			gpios = <&pca0 13 GPIO_ACTIVE_LOW>;
 			linux,code = <7>;
 		};
 
-		bmc-rom0-wp {
+		event-bmc-rom0-wp {
 			label = "bmc-rom0-wp";
 			gpios = <&pca1 0 GPIO_ACTIVE_LOW>;
 			linux,code = <8>;
 		};
 
-		bmc-rom1-wp {
+		event-bmc-rom1-wp {
 			label = "bmc-rom1-wp";
 			gpios = <&pca1 1 GPIO_ACTIVE_LOW>;
 			linux,code = <9>;
 		};
 
-		fan0-presence {
+		event-fan0-presence {
 			label = "fan0-presence";
 			gpios = <&pca1 2 GPIO_ACTIVE_LOW>;
 			linux,code = <10>;
 		};
 
-		fan1-presence {
+		event-fan1-presence {
 			label = "fan1-presence";
 			gpios = <&pca1 3 GPIO_ACTIVE_LOW>;
 			linux,code = <11>;
 		};
 
-		fan2-presence {
+		event-fan2-presence {
 			label = "fan2-presence";
 			gpios = <&pca1 4 GPIO_ACTIVE_LOW>;
 			linux,code = <12>;
 		};
 
-		fan3-presence {
+		event-fan3-presence {
 			label = "fan3-presence";
 			gpios = <&pca1 5 GPIO_ACTIVE_LOW>;
 			linux,code = <13>;
 		};
 
-		fan4-presence {
+		event-fan4-presence {
 			label = "fan4-presence";
 			gpios = <&pca1 6 GPIO_ACTIVE_LOW>;
 			linux,code = <14>;
 		};
 
-		fan5-presence {
+		event-fan5-presence {
 			label = "fan5-presence";
 			gpios = <&pca1 7 GPIO_ACTIVE_LOW>;
 			linux,code = <15>;
 		};
 
-		front-bp1-presence {
+		event-front-bp1-presence {
 			label = "front-bp1-presence";
 			gpios = <&pca1 8 GPIO_ACTIVE_LOW>;
 			linux,code = <16>;
 		};
 
-		rear-bp-presence {
+		event-rear-bp-presence {
 			label = "rear-bp-presence";
 			gpios = <&pca1 9 GPIO_ACTIVE_LOW>;
 			linux,code = <17>;
 		};
 
-		fault-pvccin-cpu0 {
+		event-fault-pvccin-cpu0 {
 			label = "fault-pvccin-cpu0";
 			gpios = <&pca1 10 GPIO_ACTIVE_LOW>;
 			linux,code = <18>;
 		};
 
-		alrt-p1v05-pvcc {
+		event-alrt-p1v05-pvcc {
 			label = "alrt-p1v05-pvcc1";
 			gpios = <&pca1 11 GPIO_ACTIVE_LOW>;
 			linux,code = <19>;
 		};
 
-		fault-p1v05-pvccio {
+		event-fault-p1v05-pvccio {
 			label = "alrt-p1v05-pvcc1";
 			gpios = <&pca1 12 GPIO_ACTIVE_LOW>;
 			linux,code = <20>;
 		};
 
-		alrt-p1v8-pvccio {
+		event-alrt-p1v8-pvccio {
 			label = "alrt-p1v8-pvccio";
 			gpios = <&pca1 13 GPIO_ACTIVE_LOW>;
 			linux,code = <21>;
 		};
 
-		fault-p1v8-pvccio {
+		event-fault-p1v8-pvccio {
 			label = "fault-p1v8-pvccio";
 			gpios = <&pca1 14 GPIO_ACTIVE_LOW>;
 			linux,code = <22>;
 		};
 
-		front-bp0-presence {
+		event-front-bp0-presence {
 			label = "front-bp0-presence";
 			gpios = <&pca1 15 GPIO_ACTIVE_LOW>;
 			linux,code = <23>;
@@ -260,6 +260,13 @@
 		spi-max-frequency = <50000000>;
 #include "openbmc-flash-layout-64.dtsi"
 	};
+	flash@1 {
+		status = "okay";
+		label = "alt-bmc";
+		m25p,fast-read;
+		spi-max-frequency = <50000000>;
+#include "openbmc-flash-layout-64-alt.dtsi"
+	};
 };
 
 &spi1 {
@@ -278,6 +285,11 @@
 	status = "okay";
 };
 
+&wdt2 {
+	status = "okay";
+	aspeed,alt-boot;
+};
+
 &gpio {
 	status = "okay";
 	gpio-line-names =
diff --git a/arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts b/arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts
new file mode 100644
index 000000000000..1fc3e7cbf0d1
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts
@@ -0,0 +1,955 @@
+// SPDX-License-Identifier: GPL-2.0+
+// Copyright (c) 2021 Facebook Inc.
+/dts-v1/;
+
+#include "aspeed-g6.dtsi"
+#include <dt-bindings/gpio/aspeed-gpio.h>
+#include <dt-bindings/usb/pd.h>
+#include <dt-bindings/leds/leds-pca955x.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/i2c/i2c.h>
+
+/ {
+	model = "Facebook Bletchley BMC";
+	compatible = "facebook,bletchley-bmc", "aspeed,ast2600";
+
+	aliases {
+		serial4 = &uart5;
+	};
+
+	chosen {
+		bootargs = "console=ttyS4,57600n8";
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x80000000>;
+	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc0 0>, <&adc0 1>, <&adc0 2>, <&adc0 3>,
+			<&adc0 4>, <&adc0 5>, <&adc0 6>, <&adc0 7>,
+			<&adc1 0>, <&adc1 1>, <&adc1 2>, <&adc1 3>,
+			<&adc1 4>, <&adc1 5>, <&adc1 6>, <&adc1 7>;
+	};
+
+	spi1_gpio: spi1-gpio {
+		compatible = "spi-gpio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		gpio-sck = <&gpio0 ASPEED_GPIO(Z, 3) GPIO_ACTIVE_HIGH>;
+		gpio-mosi = <&gpio0 ASPEED_GPIO(Z, 4) GPIO_ACTIVE_HIGH>;
+		gpio-miso = <&gpio0 ASPEED_GPIO(Z, 5) GPIO_ACTIVE_HIGH>;
+		num-chipselects = <1>;
+		cs-gpios = <&gpio0 ASPEED_GPIO(Z, 0) GPIO_ACTIVE_LOW>;
+
+		tpmdev@0 {
+			compatible = "tcg,tpm_tis-spi";
+			spi-max-frequency = <33000000>;
+			reg = <0>;
+		};
+	};
+
+	switchphy: ethernet-phy@0 {
+		// Fixed link
+	};
+
+	front_gpio_leds {
+		compatible = "gpio-leds";
+		sys_log_id {
+			default-state = "off";
+			gpios = <&front_leds 0 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	fan_gpio_leds {
+		compatible = "gpio-leds";
+		fan0_blue {
+			retain-state-shutdown;
+			default-state = "on";
+			gpios = <&fan_leds 8 GPIO_ACTIVE_HIGH>;
+		};
+		fan1_blue {
+			retain-state-shutdown;
+			default-state = "on";
+			gpios = <&fan_leds 9 GPIO_ACTIVE_HIGH>;
+		};
+		fan2_blue {
+			retain-state-shutdown;
+			default-state = "on";
+			gpios = <&fan_leds 10 GPIO_ACTIVE_HIGH>;
+		};
+		fan3_blue {
+			retain-state-shutdown;
+			default-state = "on";
+			gpios = <&fan_leds 11 GPIO_ACTIVE_HIGH>;
+		};
+		fan0_amber {
+			retain-state-shutdown;
+			default-state = "off";
+			gpios = <&fan_leds 12 GPIO_ACTIVE_HIGH>;
+		};
+		fan1_amber {
+			retain-state-shutdown;
+			default-state = "off";
+			gpios = <&fan_leds 13 GPIO_ACTIVE_HIGH>;
+		};
+		fan2_amber {
+			retain-state-shutdown;
+			default-state = "off";
+			gpios = <&fan_leds 14 GPIO_ACTIVE_HIGH>;
+		};
+		fan3_amber {
+			retain-state-shutdown;
+			default-state = "off";
+			gpios = <&fan_leds 15 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	sled1_gpio_leds {
+		compatible = "gpio-leds";
+		sled1_amber {
+			retain-state-shutdown;
+			default-state = "keep";
+			gpios = <&sled1_leds 0 GPIO_ACTIVE_LOW>;
+		};
+		sled1_blue {
+			retain-state-shutdown;
+			default-state = "keep";
+			gpios = <&sled1_leds 1 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	sled2_gpio_leds {
+		compatible = "gpio-leds";
+		sled2_amber {
+			retain-state-shutdown;
+			default-state = "keep";
+			gpios = <&sled2_leds 0 GPIO_ACTIVE_LOW>;
+		};
+		sled2_blue {
+			retain-state-shutdown;
+			default-state = "keep";
+			gpios = <&sled2_leds 1 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	sled3_gpio_leds {
+		compatible = "gpio-leds";
+		sled3_amber {
+			retain-state-shutdown;
+			default-state = "keep";
+			gpios = <&sled3_leds 0 GPIO_ACTIVE_LOW>;
+		};
+		sled3_blue {
+			retain-state-shutdown;
+			default-state = "keep";
+			gpios = <&sled3_leds 1 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	sled4_gpio_leds {
+		compatible = "gpio-leds";
+		sled4_amber {
+			retain-state-shutdown;
+			default-state = "keep";
+			gpios = <&sled4_leds 0 GPIO_ACTIVE_LOW>;
+		};
+		sled4_blue {
+			retain-state-shutdown;
+			default-state = "keep";
+			gpios = <&sled4_leds 1 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	sled5_gpio_leds {
+		compatible = "gpio-leds";
+		sled5_amber {
+			retain-state-shutdown;
+			default-state = "keep";
+			gpios = <&sled5_leds 0 GPIO_ACTIVE_LOW>;
+		};
+		sled5_blue {
+			retain-state-shutdown;
+			default-state = "keep";
+			gpios = <&sled5_leds 1 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	sled6_gpio_leds {
+		compatible = "gpio-leds";
+		sled6_amber {
+			retain-state-shutdown;
+			default-state = "keep";
+			gpios = <&sled6_leds 0 GPIO_ACTIVE_LOW>;
+		};
+		sled6_blue {
+			retain-state-shutdown;
+			default-state = "keep";
+			gpios = <&sled6_leds 1 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&mac2 {
+	status = "okay";
+	phy-mode = "rgmii";
+	phy-handle = <&switchphy>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rgmii3_default>;
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+};
+
+&fmc {
+	status = "okay";
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "bmc";
+		spi-max-frequency = <50000000>;
+#include "openbmc-flash-layout-128.dtsi"
+	};
+	flash@1 {
+		status = "okay";
+		m25p,fast-read;
+		label = "flash1";
+		spi-max-frequency = <50000000>;
+	};
+};
+
+&spi2 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_spi2_default>;
+
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "pnor";
+		spi-max-frequency = <50000000>;
+	};
+};
+
+&i2c0 {
+	status = "okay";
+	ina230@45 {
+		compatible = "ti,ina230";
+		reg = <0x45>;
+		shunt-resistor = <2000>;
+	};
+
+	mp5023@40 {
+		compatible = "mps,mp5023";
+		reg = <0x40>;
+	};
+
+	tmp421@4f {
+		compatible = "ti,tmp421";
+		reg = <0x4f>;
+	};
+
+	sled1_ioexp41: pca9536@41 {
+		compatible = "nxp,pca9536";
+		reg = <0x41>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names =
+		"SLED1_SWD_MUX", "SLED1_XRES_SWD_N",
+		"SLED1_CLKREQ_N", "SLED1_PCIE_PWR_EN";
+	};
+
+	sled1_ioexp: pca9539@76 {
+		compatible = "nxp,pca9539";
+		reg = <0x76>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-parent = <&gpio0>;
+		interrupts = <ASPEED_GPIO(M, 0) IRQ_TYPE_LEVEL_LOW>;
+
+		gpio-line-names =
+		"SLED1_MS_DETECT1","SLED1_VBUS_BMC_EN","SLED1_INA230_ALERT","SLED1_P12V_STBY_ALERT",
+		"SLED1_SSD_ALERT","SLED1_MS_DETECT0","SLED1_RST_CCG5","SLED1_FUSB302_INT",
+		"SLED1_MD_STBY_RESET","SLED1_MD_IOEXP_EN_FAULT","SLED1_MD_DIR","SLED1_MD_DECAY",
+		"SLED1_MD_MODE1","SLED1_MD_MODE2","SLED1_MD_MODE3","power-host1";
+	};
+
+	sled1_leds: pca9552@67 {
+		compatible = "nxp,pca9552";
+		reg = <0x67>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names =
+		"led-sled1-amber","led-sled1-blue","SLED1_RST_IOEXP","SLED1_MD_REF_PWM",
+		"","","","",
+		"","","","",
+		"","","","";
+	};
+
+	sled1_fusb302: typec-portc@22 {
+		compatible = "fcs,fusb302";
+		reg = <0x22>;
+
+		connector {
+			compatible = "usb-c-connector";
+			label = "USB-C";
+			power-role = "dual";
+			try-power-role = "sink";
+			data-role = "dual";
+			source-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
+			sink-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)
+					PDO_VAR(3000, 12000, 3000)
+					PDO_PPS_APDO(3000, 11000, 3000)>;
+			op-sink-microwatt = <10000000>;
+		};
+	};
+
+	eeprom@54 {
+		compatible = "atmel,24c64";
+		reg = <0x54>;
+	};
+};
+
+&i2c1 {
+	status = "okay";
+	ina230@45 {
+		compatible = "ti,ina230";
+		reg = <0x45>;
+		shunt-resistor = <2000>;
+	};
+
+	mp5023@40 {
+		compatible = "mps,mp5023";
+		reg = <0x40>;
+	};
+
+	tmp421@4f {
+		compatible = "ti,tmp421";
+		reg = <0x4f>;
+	};
+
+	sled2_ioexp41: pca9536@41 {
+		compatible = "nxp,pca9536";
+		reg = <0x41>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names =
+		"SLED2_SWD_MUX", "SLED2_XRES_SWD_N",
+		"SLED2_CLKREQ_N", "SLED2_PCIE_PWR_EN";
+	};
+
+	sled2_ioexp: pca9539@76 {
+		compatible = "nxp,pca9539";
+		reg = <0x76>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-parent = <&gpio0>;
+		interrupts = <ASPEED_GPIO(M, 1) IRQ_TYPE_LEVEL_LOW>;
+
+		gpio-line-names =
+		"SLED2_MS_DETECT1","SLED2_VBUS_BMC_EN","SLED2_INA230_ALERT","SLED2_P12V_STBY_ALERT",
+		"SLED2_SSD_ALERT","SLED2_MS_DETECT0","SLED2_RST_CCG5","SLED2_FUSB302_INT",
+		"SLED2_MD_STBY_RESET","SLED2_MD_IOEXP_EN_FAULT","SLED2_MD_DIR","SLED2_MD_DECAY",
+		"SLED2_MD_MODE1","SLED2_MD_MODE2","SLED2_MD_MODE3","power-host2";
+	};
+
+	sled2_leds: pca9552@67 {
+		compatible = "nxp,pca9552";
+		reg = <0x67>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names =
+		"led-sled2-amber","led-sled2-blue","SLED2_RST_IOEXP","SLED2_MD_REF_PWM",
+		"","","","",
+		"","","","",
+		"","","","";
+	};
+
+	sled2_fusb302: typec-portc@22 {
+		compatible = "fcs,fusb302";
+		reg = <0x22>;
+
+		connector {
+			compatible = "usb-c-connector";
+			label = "USB-C";
+			power-role = "dual";
+			try-power-role = "sink";
+			data-role = "dual";
+			source-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
+			sink-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)
+					PDO_VAR(3000, 12000, 3000)
+					PDO_PPS_APDO(3000, 11000, 3000)>;
+			op-sink-microwatt = <10000000>;
+		};
+	};
+
+	eeprom@54 {
+		compatible = "atmel,24c64";
+		reg = <0x54>;
+	};
+};
+
+&i2c2 {
+	status = "okay";
+	ina230@45 {
+		compatible = "ti,ina230";
+		reg = <0x45>;
+		shunt-resistor = <2000>;
+	};
+
+	mp5023@40 {
+		compatible = "mps,mp5023";
+		reg = <0x40>;
+	};
+
+	tmp421@4f {
+		compatible = "ti,tmp421";
+		reg = <0x4f>;
+	};
+
+	sled3_ioexp41: pca9536@41 {
+		compatible = "nxp,pca9536";
+		reg = <0x41>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names =
+		"SLED3_SWD_MUX", "SLED3_XRES_SWD_N",
+		"SLED3_CLKREQ_N", "SLED3_PCIE_PWR_EN";
+	};
+
+	sled3_ioexp: pca9539@76 {
+		compatible = "nxp,pca9539";
+		reg = <0x76>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-parent = <&gpio0>;
+		interrupts = <ASPEED_GPIO(M, 2) IRQ_TYPE_LEVEL_LOW>;
+
+		gpio-line-names =
+		"SLED3_MS_DETECT1","SLED3_VBUS_BMC_EN","SLED3_INA230_ALERT","SLED3_P12V_STBY_ALERT",
+		"SLED3_SSD_ALERT","SLED3_MS_DETECT0","SLED3_RST_CCG5","SLED3_FUSB302_INT",
+		"SLED3_MD_STBY_RESET","SLED3_MD_IOEXP_EN_FAULT","SLED3_MD_DIR","SLED3_MD_DECAY",
+		"SLED3_MD_MODE1","SLED3_MD_MODE2","SLED3_MD_MODE3","power-host3";
+	};
+
+	sled3_leds: pca9552@67 {
+		compatible = "nxp,pca9552";
+		reg = <0x67>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names =
+		"led-sled3-amber","led-sled3-blue","SLED3_RST_IOEXP","SLED3_MD_REF_PWM",
+		"","","","",
+		"","","","",
+		"","","","";
+	};
+
+	sled3_fusb302: typec-portc@22 {
+		compatible = "fcs,fusb302";
+		reg = <0x22>;
+
+		connector {
+			compatible = "usb-c-connector";
+			label = "USB-C";
+			power-role = "dual";
+			try-power-role = "sink";
+			data-role = "dual";
+			source-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
+			sink-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)
+					PDO_VAR(3000, 12000, 3000)
+					PDO_PPS_APDO(3000, 11000, 3000)>;
+			op-sink-microwatt = <10000000>;
+		};
+	};
+
+	eeprom@54 {
+		compatible = "atmel,24c64";
+		reg = <0x54>;
+	};
+};
+
+&i2c3 {
+	status = "okay";
+	ina230@45 {
+		compatible = "ti,ina230";
+		reg = <0x45>;
+		shunt-resistor = <2000>;
+	};
+
+	mp5023@40 {
+		compatible = "mps,mp5023";
+		reg = <0x40>;
+	};
+
+	tmp421@4f {
+		compatible = "ti,tmp421";
+		reg = <0x4f>;
+	};
+
+	sled4_ioexp41: pca9536@41 {
+		compatible = "nxp,pca9536";
+		reg = <0x41>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names =
+		"SLED4_SWD_MUX", "SLED4_XRES_SWD_N",
+		"SLED4_CLKREQ_N", "SLED4_PCIE_PWR_EN";
+	};
+
+	sled4_ioexp: pca9539@76 {
+		compatible = "nxp,pca9539";
+		reg = <0x76>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-parent = <&gpio0>;
+		interrupts = <ASPEED_GPIO(M, 3) IRQ_TYPE_LEVEL_LOW>;
+
+		gpio-line-names =
+		"SLED4_MS_DETECT1","SLED4_VBUS_BMC_EN","SLED4_INA230_ALERT","SLED4_P12V_STBY_ALERT",
+		"SLED4_SSD_ALERT","SLED4_MS_DETECT0","SLED4_RST_CCG5","SLED4_FUSB302_INT",
+		"SLED4_MD_STBY_RESET","SLED4_MD_IOEXP_EN_FAULT","SLED4_MD_DIR","SLED4_MD_DECAY",
+		"SLED4_MD_MODE1","SLED4_MD_MODE2","SLED4_MD_MODE3","power-host4";
+	};
+
+	sled4_leds: pca9552@67 {
+		compatible = "nxp,pca9552";
+		reg = <0x67>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names =
+		"led-sled4-amber","led-sled4-blue","SLED4_RST_IOEXP","SLED4_MD_REF_PWM",
+		"","","","",
+		"","","","",
+		"","","","";
+	};
+
+	sled4_fusb302: typec-portc@22 {
+		compatible = "fcs,fusb302";
+		reg = <0x22>;
+
+		connector {
+			compatible = "usb-c-connector";
+			label = "USB-C";
+			power-role = "dual";
+			try-power-role = "sink";
+			data-role = "dual";
+			source-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
+			sink-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)
+					PDO_VAR(3000, 12000, 3000)
+					PDO_PPS_APDO(3000, 11000, 3000)>;
+			op-sink-microwatt = <10000000>;
+		};
+	};
+
+	eeprom@54 {
+		compatible = "atmel,24c64";
+		reg = <0x54>;
+	};
+};
+
+&i2c4 {
+	status = "okay";
+	ina230@45 {
+		compatible = "ti,ina230";
+		reg = <0x45>;
+		shunt-resistor = <2000>;
+	};
+
+	mp5023@40 {
+		compatible = "mps,mp5023";
+		reg = <0x40>;
+	};
+
+	tmp421@4f {
+		compatible = "ti,tmp421";
+		reg = <0x4f>;
+	};
+
+	sled5_ioexp41: pca9536@41 {
+		compatible = "nxp,pca9536";
+		reg = <0x41>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names =
+		"SLED5_SWD_MUX", "SLED5_XRES_SWD_N",
+		"SLED5_CLKREQ_N", "SLED5_PCIE_PWR_EN";
+	};
+
+	sled5_ioexp: pca9539@76 {
+		compatible = "nxp,pca9539";
+		reg = <0x76>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-parent = <&gpio0>;
+		interrupts = <ASPEED_GPIO(M, 4) IRQ_TYPE_LEVEL_LOW>;
+
+		gpio-line-names =
+		"SLED5_MS_DETECT1","SLED5_VBUS_BMC_EN","SLED5_INA230_ALERT","SLED5_P12V_STBY_ALERT",
+		"SLED5_SSD_ALERT","SLED5_MS_DETECT0","SLED5_RST_CCG5","SLED5_FUSB302_INT",
+		"SLED5_MD_STBY_RESET","SLED5_MD_IOEXP_EN_FAULT","SLED5_MD_DIR","SLED5_MD_DECAY",
+		"SLED5_MD_MODE1","SLED5_MD_MODE2","SLED5_MD_MODE3","power-host5";
+	};
+
+	sled5_leds: pca9552@67 {
+		compatible = "nxp,pca9552";
+		reg = <0x67>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names =
+		"led-sled5-amber","led-sled5-blue","SLED5_RST_IOEXP","SLED5_MD_REF_PWM",
+		"","","","",
+		"","","","",
+		"","","","";
+	};
+
+	sled5_fusb302: typec-portc@22 {
+		compatible = "fcs,fusb302";
+		reg = <0x22>;
+
+		connector {
+			compatible = "usb-c-connector";
+			label = "USB-C";
+			power-role = "dual";
+			try-power-role = "sink";
+			data-role = "dual";
+			source-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
+			sink-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)
+					PDO_VAR(3000, 12000, 3000)
+					PDO_PPS_APDO(3000, 11000, 3000)>;
+			op-sink-microwatt = <10000000>;
+		};
+	};
+
+	eeprom@54 {
+		compatible = "atmel,24c64";
+		reg = <0x54>;
+	};
+};
+
+&i2c5 {
+	status = "okay";
+	ina230@45 {
+		compatible = "ti,ina230";
+		reg = <0x45>;
+		shunt-resistor = <2000>;
+	};
+
+	mp5023@40 {
+		compatible = "mps,mp5023";
+		reg = <0x40>;
+	};
+
+	tmp421@4f {
+		compatible = "ti,tmp421";
+		reg = <0x4f>;
+	};
+
+	sled6_ioexp41: pca9536@41 {
+		compatible = "nxp,pca9536";
+		reg = <0x41>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names =
+		"SLED6_SWD_MUX", "SLED6_XRES_SWD_N",
+		"SLED6_CLKREQ_N", "SLED6_PCIE_PWR_EN";
+	};
+
+	sled6_ioexp: pca9539@76 {
+		compatible = "nxp,pca9539";
+		reg = <0x76>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-parent = <&gpio0>;
+		interrupts = <ASPEED_GPIO(M, 5) IRQ_TYPE_LEVEL_LOW>;
+
+		gpio-line-names =
+		"SLED6_MS_DETECT1","SLED6_VBUS_BMC_EN","SLED6_INA230_ALERT","SLED6_P12V_STBY_ALERT",
+		"SLED6_SSD_ALERT","SLED6_MS_DETECT0","SLED6_RST_CCG5","SLED6_FUSB302_INT",
+		"SLED6_MD_STBY_RESET","SLED6_MD_IOEXP_EN_FAULT","SLED6_MD_DIR","SLED6_MD_DECAY",
+		"SLED6_MD_MODE1","SLED6_MD_MODE2","SLED6_MD_MODE3","power-host6";
+	};
+
+	sled6_leds: pca9552@67 {
+		compatible = "nxp,pca9552";
+		reg = <0x67>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names =
+		"led-sled6-amber","led-sled6-blue","SLED6_RST_IOEXP","SLED6_MD_REF_PWM",
+		"","","","",
+		"","","","",
+		"","","","";
+	};
+
+	sled6_fusb302: typec-portc@22 {
+		compatible = "fcs,fusb302";
+		reg = <0x22>;
+
+		connector {
+			compatible = "usb-c-connector";
+			label = "USB-C";
+			power-role = "dual";
+			try-power-role = "sink";
+			data-role = "dual";
+			source-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
+			sink-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)
+					PDO_VAR(3000, 12000, 3000)
+					PDO_PPS_APDO(3000, 11000, 3000)>;
+			op-sink-microwatt = <10000000>;
+		};
+	};
+
+	eeprom@54 {
+		compatible = "atmel,24c64";
+		reg = <0x54>;
+	};
+};
+
+&i2c6 {
+	status = "okay";
+
+	eeprom@56 {
+		compatible = "atmel,24c64";
+		reg = <0x56>;
+	};
+
+	rtc@51 {
+		/* in-chip rtc disabled, use external rtc (battery-backed) */
+		compatible = "nxp,pcf85263";
+		reg = <0x51>;
+	};
+};
+
+&i2c7 {
+	status = "okay";
+
+	eeprom@54 {
+		compatible = "atmel,24c64";
+		reg = <0x54>;
+	};
+};
+
+&i2c9 {
+	status = "okay";
+
+	tmp421@4f {
+		compatible = "ti,tmp421";
+		reg = <0x4f>;
+	};
+};
+
+&i2c10 {
+	status = "okay";
+
+	tmp421@4f {
+		compatible = "ti,tmp421";
+		reg = <0x4f>;
+	};
+
+	front_leds: pca9552@67 {
+		compatible = "nxp,pca9552";
+		reg = <0x67>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names =
+		"led-fault-identify","power-p5v-stby-good",
+		"power-p1v0-dvdd-good","power-p1v0-avdd-good",
+		"","","","",
+		"","","","",
+		"","","","";
+	};
+};
+
+&i2c12 {
+	status = "okay";
+
+	adm1278@11 {
+		compatible = "adi,adm1278";
+		reg = <0x11>;
+		shunt-resistor-micro-ohms = <300>;
+		adi,volt-curr-sample-average = <128>;
+		adi,power-sample-average = <128>;
+	};
+
+	tmp421@4c {
+		compatible = "ti,tmp421";
+		reg = <0x4c>;
+	};
+
+	tmp421@4d {
+		compatible = "ti,tmp421";
+		reg = <0x4d>;
+	};
+
+	fan_leds: pca9552@67 {
+		compatible = "nxp,pca9552";
+		reg = <0x67>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names =
+		"presence-fan0","presence-fan1",
+		"presence-fan2","presence-fan3",
+		"power-fan0-good","power-fan1-good",
+		"power-fan2-good","power-fan3-good",
+		"","","","",
+		"","","","";
+	};
+};
+
+&i2c13 {
+	multi-master;
+	aspeed,hw-timeout-ms = <1000>;
+	status = "okay";
+
+	//USB Debug Connector
+	ipmb13@10 {
+		compatible = "ipmb-dev";
+		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
+		i2c-protocol;
+	};
+};
+
+&gpio0 {
+	gpio-line-names =
+	/*A0-A7*/	"","","","","","","","",
+	/*B0-B7*/	"FUSB302_SLED1_INT_N","FUSB302_SLED2_INT_N",
+			"SEL_SPI2_MUX","SPI2_MUX1",
+			"SPI2_MUX2","SPI2_MUX3",
+			"","FUSB302_SLED3_INT_N",
+	/*C0-C7*/	"","","","","","","","",
+	/*D0-D7*/	"","","","","","","","",
+	/*E0-E7*/	"","","","","","","","",
+	/*F0-F7*/	"BMC_SLED1_STCK","BMC_SLED2_STCK",
+			"BMC_SLED3_STCK","BMC_SLED4_STCK",
+			"BMC_SLED5_STCK","BMC_SLED6_STCK",
+			"","",
+	/*G0-G7*/	"BSM_FRU_WP","SWITCH_FRU_MUX","","FM_SOL_UART_CH_SEL",
+			"PWRGD_P1V05_VDDCORE","PWRGD_P1V5_VDD","","",
+	/*H0-H7*/	"presence-riser1","presence-riser2",
+			"presence-sled1","presence-sled2",
+			"presence-sled3","presence-sled4",
+			"presence-sled5","presence-sled6",
+	/*I0-I7*/	"REV_ID0","",
+			"REV_ID1","REV_ID2",
+			"","BSM_FLASH_WP_STATUS",
+			"BMC_TPM_PRES_N","FUSB302_SLED6_INT_N",
+	/*J0-J7*/	"","","","","","","","",
+	/*K0-K7*/	"","","","","","","","",
+	/*L0-L7*/	"","","","","","BMC_RTC_INT","","",
+	/*M0-M7*/	"ALERT_SLED1_N","ALERT_SLED2_N",
+			"ALERT_SLED3_N","ALERT_SLED4_N",
+			"ALERT_SLED5_N","ALERT_SLED6_N",
+			"","",
+	/*N0-N7*/	"LED_POSTCODE_0","LED_POSTCODE_1",
+			"LED_POSTCODE_2","LED_POSTCODE_3",
+			"LED_POSTCODE_4","LED_POSTCODE_5",
+			"LED_POSTCODE_5","LED_POSTCODE_7",
+	/*O0-O7*/	"","","","",
+			"","BOARD_ID0","BOARD_ID1","BOARD_ID2",
+	/*P0-P7*/	"","","","","","","","BMC_HEARTBEAT",
+	/*Q0-Q7*/	"","","","","","","","",
+	/*R0-R7*/	"","","","","","","","",
+	/*S0-S7*/	"","","","BAT_DETECT",
+			"BMC_BT_WP0_N","BMC_BT_WP1_N","","FUSB302_SLED4_INT_N",
+	/*T0-T7*/	"","","","","","","","",
+	/*U0-U7*/	"","","","","","","","",
+	/*V0-V7*/	"PWRGD_CNS_PSU","RST_BMC_MVL_N",
+			"P12V_AUX_ALERT1_N","PSU_PRSNT",
+			"USB2_SEL0_A","USB2_SEL1_A",
+			"USB2_SEL0_B","USB2_SEL1_B",
+	/*W0-W7*/	"RST_FRONT_IOEXP_N","","","","","","","",
+	/*X0-X7*/	"","","","","","","","",
+	/*Y0-Y7*/	"BMC_SELF_HW_RST","BSM_PRSNT_N",
+			"BSM_FLASH_LATCH_N","FUSB302_SLED5_INT_N",
+			"","","","",
+	/*Z0-Z7*/	"","","","","","","","";
+};
+
+&adc0 {
+	vref = <1800>;
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc0_default &pinctrl_adc1_default
+		&pinctrl_adc2_default &pinctrl_adc3_default
+		&pinctrl_adc4_default &pinctrl_adc5_default
+		&pinctrl_adc6_default &pinctrl_adc7_default>;
+};
+
+&adc1 {
+	vref = <2500>;
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc8_default &pinctrl_adc9_default
+		&pinctrl_adc10_default &pinctrl_adc11_default
+		&pinctrl_adc12_default &pinctrl_adc13_default
+		&pinctrl_adc14_default &pinctrl_adc15_default>;
+};
+
+&mdio0 {
+	status = "okay";
+	/* TODO: Add Marvell 88E6191X */
+};
+
+&mdio3 {
+	status = "okay";
+	/* TODO: Add Marvell 88X3310 */
+};
+
+&ehci0 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/aspeed-bmc-facebook-elbert.dts b/arch/arm/boot/dts/aspeed-bmc-facebook-elbert.dts
index 27b43fe099f1..8e1a1d1b282d 100644
--- a/arch/arm/boot/dts/aspeed-bmc-facebook-elbert.dts
+++ b/arch/arm/boot/dts/aspeed-bmc-facebook-elbert.dts
@@ -183,3 +183,21 @@
 &i2c11 {
 	status = "okay";
 };
+
+/*
+ * BMC's "mac3" controller is connected to BCM53134P's IMP_RGMII port
+ * directly (fixed link, no PHY in between).
+ * Note: BMC's "mdio0" controller is connected to BCM53134P's MDIO
+ * interface, and the MDIO channel will be enabled in dts later, when
+ * BCM53134 is added to "bcm53xx" DSA driver.
+ */
+&mac3 {
+	status = "okay";
+	phy-mode = "rgmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rgmii4_default>;
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+};
diff --git a/arch/arm/boot/dts/aspeed-bmc-facebook-yosemitev2.dts b/arch/arm/boot/dts/aspeed-bmc-facebook-yosemitev2.dts
index 8864e9c312a8..6bf2ff85a40e 100644
--- a/arch/arm/boot/dts/aspeed-bmc-facebook-yosemitev2.dts
+++ b/arch/arm/boot/dts/aspeed-bmc-facebook-yosemitev2.dts
@@ -207,11 +207,16 @@
 
 &i2c12 {
 	status = "okay";
-	//MEZZ_FRU
-	eeprom@51 {
-		compatible = "atmel,24c64";
-		reg = <0x51>;
-		pagesize = <32>;
+};
+
+&i2c13 {
+	status = "okay";
+	// Debug Card
+	multi-master;
+	ipmb13@10 {
+		compatible = "ipmb-dev";
+		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
+		i2c-protocol;
 	};
 };
 
diff --git a/arch/arm/boot/dts/aspeed-bmc-ibm-everest.dts b/arch/arm/boot/dts/aspeed-bmc-ibm-everest.dts
index f42e2d776ba8..a6a2bc3b855c 100644
--- a/arch/arm/boot/dts/aspeed-bmc-ibm-everest.dts
+++ b/arch/arm/boot/dts/aspeed-bmc-ibm-everest.dts
@@ -171,9 +171,10 @@
 		/* 48MB region from the end of flash to start of vga memory */
 		ramoops@bc000000 {
 			compatible = "ramoops";
-			reg = <0xbc000000 0x180000>; /* 16 * (3 * 0x8000) */
+			reg = <0xbc000000 0x200000>; /* 16 * (4 * 0x8000) */
 			record-size = <0x8000>;
 			console-size = <0x8000>;
+			ftrace-size = <0x8000>;
 			pmsg-size = <0x8000>;
 			max-reason = <3>; /* KMSG_DUMP_EMERG */
 		};
@@ -188,29 +189,27 @@
 
 	gpio-keys-polled {
 		compatible = "gpio-keys-polled";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		poll-interval = <1000>;
 
-		fan0-presence {
+		event-fan0-presence {
 			label = "fan0-presence";
 			gpios = <&pca0 15 GPIO_ACTIVE_LOW>;
 			linux,code = <15>;
 		};
 
-		fan1-presence {
+		event-fan1-presence {
 			label = "fan1-presence";
 			gpios = <&pca0 14 GPIO_ACTIVE_LOW>;
 			linux,code = <14>;
 		};
 
-		fan2-presence {
+		event-fan2-presence {
 			label = "fan2-presence";
 			gpios = <&pca0 13 GPIO_ACTIVE_LOW>;
 			linux,code = <13>;
 		};
 
-		fan3-presence {
+		event-fan3-presence {
 			label = "fan3-presence";
 			gpios = <&pca0 12 GPIO_ACTIVE_LOW>;
 			linux,code = <12>;
@@ -269,9 +268,7 @@
 	/*C0-C7*/	"","","","","","","","",
 	/*D0-D7*/	"","","","","","","","",
 	/*E0-E7*/	"","","","","","","","",
-	/*F0-F7*/	"PIN_HOLE_RESET_IN_N","","",
-				"PIN_HOLE_RESET_OUT_N","","",
-				"factory-reset-toggle","",
+	/*F0-F7*/	"","","rtc-battery-voltage-read-enable","reset-cause-pinhole","","","factory-reset-toggle","",
 	/*G0-G7*/	"","","","","","","","",
 	/*H0-H7*/	"led-rtc-battery","led-bmc","led-rear-enc-id0","led-rear-enc-fault0","","","","",
 	/*I0-I7*/	"","","","","","","bmc-secure-boot","",
@@ -280,11 +277,11 @@
 	/*L0-L7*/	"","","","","","","","",
 	/*M0-M7*/	"","","","","","","","",
 	/*N0-N7*/	"","","","","","","","",
-	/*O0-O7*/	"","","","","","","","",
+	/*O0-O7*/	"","","","usb-power","","","","",
 	/*P0-P7*/	"","","","","led-pcieslot-power","","","",
 	/*Q0-Q7*/	"","","regulator-standby-faulted","","","","","",
 	/*R0-R7*/	"bmc-tpm-reset","power-chassis-control","power-chassis-good","","","I2C_FLASH_MICRO_N","","",
-	/*S0-S7*/	"","","","","","","","",
+	/*S0-S7*/	"","","","","power-ffs-sync-history","","","",
 	/*T0-T7*/	"","","","","","","","",
 	/*U0-U7*/	"","","","","","","","",
 	/*V0-V7*/	"","BMC_3RESTART_ATTEMPT_P","","","","","","",
@@ -292,6 +289,12 @@
 	/*X0-X7*/	"","","","","","","","",
 	/*Y0-Y7*/	"","","","","","","","",
 	/*Z0-Z7*/   "","","","","","","","";
+
+	usb_power {
+		gpio-hog;
+		gpios = <ASPEED_GPIO(O, 3) GPIO_ACTIVE_LOW>;
+		output-high;
+	};
 };
 
 &i2c0 {
@@ -1881,6 +1884,11 @@
 
 &i2c12 {
 	status = "okay";
+
+	tpm@2e {
+		compatible = "nuvoton,npct75x", "tcg,tpm-tis-i2c";
+		reg = <0x2e>;
+	};
 };
 
 &i2c13 {
@@ -2375,10 +2383,18 @@
 	};
 };
 
+&ehci0 {
+	status = "okay";
+};
+
 &ehci1 {
 	status = "okay";
 };
 
+&uhci {
+	status = "okay";
+};
+
 &emmc_controller {
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts b/arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts
index 866f32cdccea..bf59a9962379 100644
--- a/arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts
+++ b/arch/arm/boot/dts/aspeed-bmc-ibm-rainier.dts
@@ -102,9 +102,10 @@
 
 		ramoops@bc000000 {
 			compatible = "ramoops";
-			reg = <0xbc000000 0x180000>; /* 16 * (3 * 0x8000) */
+			reg = <0xbc000000 0x200000>; /* 16 * (4 * 0x8000) */
 			record-size = <0x8000>;
 			console-size = <0x8000>;
+			ftrace-size = <0x8000>;
 			pmsg-size = <0x8000>;
 			max-reason = <3>; /* KMSG_DUMP_EMERG */
 		};
@@ -178,41 +179,39 @@
 
 	gpio-keys-polled {
 		compatible = "gpio-keys-polled";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		poll-interval = <1000>;
 
-		fan0-presence {
+		event-fan0-presence {
 			label = "fan0-presence";
 			gpios = <&pca0 6 GPIO_ACTIVE_LOW>;
 			linux,code = <6>;
 		};
 
-		fan1-presence {
+		event-fan1-presence {
 			label = "fan1-presence";
 			gpios = <&pca0 7 GPIO_ACTIVE_LOW>;
 			linux,code = <7>;
 		};
 
-		fan2-presence {
+		event-fan2-presence {
 			label = "fan2-presence";
 			gpios = <&pca0 8 GPIO_ACTIVE_LOW>;
 			linux,code = <8>;
 		};
 
-		fan3-presence {
+		event-fan3-presence {
 			label = "fan3-presence";
 			gpios = <&pca0 9 GPIO_ACTIVE_LOW>;
 			linux,code = <9>;
 		};
 
-		fan4-presence {
+		event-fan4-presence {
 			label = "fan4-presence";
 			gpios = <&pca0 10 GPIO_ACTIVE_LOW>;
 			linux,code = <10>;
 		};
 
-		fan5-presence {
+		event-fan5-presence {
 			label = "fan5-presence";
 			gpios = <&pca0 11 GPIO_ACTIVE_LOW>;
 			linux,code = <11>;
@@ -239,6 +238,10 @@
 	status = "okay";
 };
 
+&uhci {
+	status = "okay";
+};
+
 &gpio0 {
 	gpio-line-names =
 	/*A0-A7*/	"","","","","","","","",
@@ -246,7 +249,7 @@
 	/*C0-C7*/	"","","","","","","","",
 	/*D0-D7*/	"","","","","","","","",
 	/*E0-E7*/	"","","","","","","","",
-	/*F0-F7*/	"","","","","","","factory-reset-toggle","",
+	/*F0-F7*/	"","","rtc-battery-voltage-read-enable","reset-cause-pinhole","","","factory-reset-toggle","",
 	/*G0-G7*/	"","","","","","","","",
 	/*H0-H7*/	"","bmc-ingraham0","rear-enc-id0","rear-enc-fault0","","","","",
 	/*I0-I7*/	"","","","","","","bmc-secure-boot","",
@@ -260,7 +263,7 @@
 	/*Q0-Q7*/	"cfam-reset","","regulator-standby-faulted","","","","","",
 	/*R0-R7*/	"bmc-tpm-reset","power-chassis-control","power-chassis-good","","","","","",
 	/*S0-S7*/	"presence-ps0","presence-ps1","presence-ps2","presence-ps3",
-				"","","","",
+	"power-ffs-sync-history","","","",
 	/*T0-T7*/	"","","","","","","","",
 	/*U0-U7*/	"","","","","","","","",
 	/*V0-V7*/	"","","","","","","","",
@@ -275,6 +278,12 @@
 		output-high;
 		line-name = "I2C3_MUX_OE_N";
 	};
+
+	usb_power {
+		gpio-hog;
+		gpios = <ASPEED_GPIO(O, 3) GPIO_ACTIVE_LOW>;
+		output-high;
+	};
 };
 
 &emmc_controller {
@@ -2061,6 +2070,11 @@
 &i2c12 {
 	status = "okay";
 
+	tpm@2e {
+		compatible = "nuvoton,npct75x";
+		reg = <0x2e>;
+	};
+
 	eeprom@50 {
 		compatible = "atmel,24c64";
 		reg = <0x50>;
@@ -2349,30 +2363,6 @@
 	use-ncsi;
 };
 
-&fmc {
-	status = "okay";
-	flash@0 {
-		status = "okay";
-		m25p,fast-read;
-		label = "bmc";
-		spi-max-frequency = <50000000>;
-#include "openbmc-flash-layout-128.dtsi"
-	};
-};
-
-&spi1 {
-	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_spi1_default>;
-
-	flash@0 {
-		status = "okay";
-		m25p,fast-read;
-		label = "pnor";
-		spi-max-frequency = <100000000>;
-	};
-};
-
 &wdt1 {
 	aspeed,reset-type = "none";
 	aspeed,external-signal;
diff --git a/arch/arm/boot/dts/aspeed-bmc-inspur-fp5280g2.dts b/arch/arm/boot/dts/aspeed-bmc-inspur-fp5280g2.dts
index 60a39ea10ab1..208b0f094ed9 100644
--- a/arch/arm/boot/dts/aspeed-bmc-inspur-fp5280g2.dts
+++ b/arch/arm/boot/dts/aspeed-bmc-inspur-fp5280g2.dts
@@ -73,19 +73,19 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		checkstop {
+		event-checkstop {
 			label = "checkstop";
 			gpios = <&gpio ASPEED_GPIO(B, 3) GPIO_ACTIVE_LOW>;
 			linux,code = <ASPEED_GPIO(B, 3)>;
 		};
 
-		ps0-presence {
+		event-ps0-presence {
 			label = "ps0-presence";
 			gpios = <&gpio ASPEED_GPIO(F, 0) GPIO_ACTIVE_LOW>;
 			linux,code = <ASPEED_GPIO(F, 0)>;
 		};
 
-		ps1-presence {
+		event-ps1-presence {
 			label = "ps1-presence";
 			gpios = <&gpio ASPEED_GPIO(F, 1) GPIO_ACTIVE_LOW>;
 			linux,code = <ASPEED_GPIO(F, 1)>;
@@ -97,49 +97,49 @@
 		compatible = "gpio-keys-polled";
 		poll-interval = <1000>;
 
-		fan0-presence {
+		event-fan0-presence {
 			label = "fan0-presence";
 			gpios = <&pca1 0 GPIO_ACTIVE_LOW>;
 			linux,code = <1>;
 		};
 
-		fan1-presence {
+		event-fan1-presence {
 			label = "fan1-presence";
 			gpios = <&pca1 1 GPIO_ACTIVE_LOW>;
 			linux,code = <2>;
 		};
 
-		fan2-presence {
+		event-fan2-presence {
 			label = "fan2-presence";
 			gpios = <&pca1 2 GPIO_ACTIVE_LOW>;
 			linux,code = <3>;
 		};
 
-		fan3-presence {
+		event-fan3-presence {
 			label = "fan3-presence";
 			gpios = <&pca1 3 GPIO_ACTIVE_LOW>;
 			linux,code = <4>;
 		};
 
-		fan4-presence {
+		event-fan4-presence {
 			label = "fan4-presence";
 			gpios = <&pca1 4 GPIO_ACTIVE_LOW>;
 			linux,code = <5>;
 		};
 
-		fan5-presence {
+		event-fan5-presence {
 			label = "fan5-presence";
 			gpios = <&pca1 5 GPIO_ACTIVE_LOW>;
 			linux,code = <6>;
 		};
 
-		fan6-presence {
+		event-fan6-presence {
 			label = "fan6-presence";
 			gpios = <&pca1 6 GPIO_ACTIVE_LOW>;
 			linux,code = <7>;
 		};
 
-		fan7-presence {
+		event-fan7-presence {
 			label = "fan7-presence";
 			gpios = <&pca1 7 GPIO_ACTIVE_LOW>;
 			linux,code = <8>;
diff --git a/arch/arm/boot/dts/aspeed-bmc-opp-mihawk.dts b/arch/arm/boot/dts/aspeed-bmc-opp-mihawk.dts
index a52a289cee85..48776fb663fb 100644
--- a/arch/arm/boot/dts/aspeed-bmc-opp-mihawk.dts
+++ b/arch/arm/boot/dts/aspeed-bmc-opp-mihawk.dts
@@ -92,30 +92,31 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		air-water {
+		event-air-water {
 			label = "air-water";
 			gpios = <&gpio ASPEED_GPIO(F, 6) GPIO_ACTIVE_LOW>;
 			linux,code = <ASPEED_GPIO(F, 6)>;
 		};
 
-		checkstop {
+		event-checkstop {
 			label = "checkstop";
 			gpios = <&gpio ASPEED_GPIO(J, 2) GPIO_ACTIVE_LOW>;
 			linux,code = <ASPEED_GPIO(J, 2)>;
 		};
 
-		ps0-presence {
+		event-ps0-presence {
 			label = "ps0-presence";
 			gpios = <&gpio ASPEED_GPIO(Z, 2) GPIO_ACTIVE_LOW>;
 			linux,code = <ASPEED_GPIO(Z, 2)>;
 		};
 
-		ps1-presence {
+		event-ps1-presence {
 			label = "ps1-presence";
 			gpios = <&gpio ASPEED_GPIO(Z, 0) GPIO_ACTIVE_LOW>;
 			linux,code = <ASPEED_GPIO(Z, 0)>;
 		};
-		id-button {
+
+		button-id {
 			label = "id-button";
 			gpios = <&gpio ASPEED_GPIO(F, 1) GPIO_ACTIVE_LOW>;
 			linux,code = <ASPEED_GPIO(F, 1)>;
@@ -126,37 +127,37 @@
 		compatible = "gpio-keys-polled";
 		poll-interval = <1000>;
 
-		fan0-presence {
+		event-fan0-presence {
 			label = "fan0-presence";
 			gpios = <&pca9552 9 GPIO_ACTIVE_LOW>;
 			linux,code = <9>;
 		};
 
-		fan1-presence {
+		event-fan1-presence {
 			label = "fan1-presence";
 			gpios = <&pca9552 10 GPIO_ACTIVE_LOW>;
 			linux,code = <10>;
 		};
 
-		fan2-presence {
+		event-fan2-presence {
 			label = "fan2-presence";
 			gpios = <&pca9552 11 GPIO_ACTIVE_LOW>;
 			linux,code = <11>;
 		};
 
-		fan3-presence {
+		event-fan3-presence {
 			label = "fan3-presence";
 			gpios = <&pca9552 12 GPIO_ACTIVE_LOW>;
 			linux,code = <12>;
 		};
 
-		fan4-presence {
+		event-fan4-presence {
 			label = "fan4-presence";
 			gpios = <&pca9552 13 GPIO_ACTIVE_LOW>;
 			linux,code = <13>;
 		};
 
-		fan5-presence {
+		event-fan5-presence {
 			label = "fan5-presence";
 			gpios = <&pca9552 14 GPIO_ACTIVE_LOW>;
 			linux,code = <14>;
diff --git a/arch/arm/boot/dts/aspeed-bmc-opp-mowgli.dts b/arch/arm/boot/dts/aspeed-bmc-opp-mowgli.dts
index 7d38d121ec6d..31ff19ef87a0 100644
--- a/arch/arm/boot/dts/aspeed-bmc-opp-mowgli.dts
+++ b/arch/arm/boot/dts/aspeed-bmc-opp-mowgli.dts
@@ -46,31 +46,31 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		air-water {
+		event-air-water {
 			label = "air-water";
 			gpios = <&gpio ASPEED_GPIO(F, 6) GPIO_ACTIVE_LOW>;
 			linux,code = <ASPEED_GPIO(F, 6)>;
 		};
 
-		checkstop {
+		event-checkstop {
 			label = "checkstop";
 			gpios = <&gpio ASPEED_GPIO(J, 2) GPIO_ACTIVE_LOW>;
 			linux,code = <ASPEED_GPIO(J, 2)>;
 		};
 
-		ps0-presence {
+		event-ps0-presence {
 			label = "ps0-presence";
 			gpios = <&gpio ASPEED_GPIO(Z, 2) GPIO_ACTIVE_LOW>;
 			linux,code = <ASPEED_GPIO(Z, 2)>;
 		};
 
-		ps1-presence {
+		event-ps1-presence {
 			label = "ps1-presence";
 			gpios = <&gpio ASPEED_GPIO(Z, 0) GPIO_ACTIVE_LOW>;
 			linux,code = <ASPEED_GPIO(Z, 0)>;
 		};
 
-		id-button {
+		button-id {
 			label = "id-button";
 			gpios = <&gpio ASPEED_GPIO(F, 1) GPIO_ACTIVE_LOW>;
 			linux,code = <ASPEED_GPIO(F, 1)>;
@@ -81,31 +81,31 @@
 		compatible = "gpio-keys-polled";
 		poll-interval = <1000>;
 
-		fan0-presence {
+		event-fan0-presence {
 			label = "fan0-presence";
 			gpios = <&pca9552 9 GPIO_ACTIVE_LOW>;
 			linux,code = <9>;
 		};
 
-		fan1-presence {
+		event-fan1-presence {
 			label = "fan1-presence";
 			gpios = <&pca9552 10 GPIO_ACTIVE_LOW>;
 			linux,code = <10>;
 		};
 
-		fan2-presence {
+		event-fan2-presence {
 			label = "fan2-presence";
 			gpios = <&pca9552 11 GPIO_ACTIVE_LOW>;
 			linux,code = <11>;
 		};
 
-		fan3-presence {
+		event-fan3-presence {
 			label = "fan3-presence";
 			gpios = <&pca9552 12 GPIO_ACTIVE_LOW>;
 			linux,code = <12>;
 		};
 
-		fan4-presence {
+		event-fan4-presence {
 			label = "fan4-presence";
 			gpios = <&pca9552 13 GPIO_ACTIVE_LOW>;
 			linux,code = <13>;
diff --git a/arch/arm/boot/dts/aspeed-bmc-opp-nicole.dts b/arch/arm/boot/dts/aspeed-bmc-opp-nicole.dts
index 3d4bdad27c2d..ac0d666ca10e 100644
--- a/arch/arm/boot/dts/aspeed-bmc-opp-nicole.dts
+++ b/arch/arm/boot/dts/aspeed-bmc-opp-nicole.dts
@@ -96,7 +96,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		checkstop {
+		event-checkstop {
 			label = "checkstop";
 			gpios = <&gpio ASPEED_GPIO(J, 2) GPIO_ACTIVE_LOW>;
 			linux,code = <ASPEED_GPIO(J, 2)>;
diff --git a/arch/arm/boot/dts/aspeed-bmc-opp-palmetto.dts b/arch/arm/boot/dts/aspeed-bmc-opp-palmetto.dts
index cd660c1ff3f5..45631b47a7b3 100644
--- a/arch/arm/boot/dts/aspeed-bmc-opp-palmetto.dts
+++ b/arch/arm/boot/dts/aspeed-bmc-opp-palmetto.dts
@@ -73,7 +73,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		checkstop {
+		event-checkstop {
 			label = "checkstop";
 			gpios = <&gpio ASPEED_GPIO(P, 5) GPIO_ACTIVE_LOW>;
 			linux,code = <ASPEED_GPIO(P, 5)>;
diff --git a/arch/arm/boot/dts/aspeed-bmc-opp-romulus.dts b/arch/arm/boot/dts/aspeed-bmc-opp-romulus.dts
index 084f54866f38..893e621ecab1 100644
--- a/arch/arm/boot/dts/aspeed-bmc-opp-romulus.dts
+++ b/arch/arm/boot/dts/aspeed-bmc-opp-romulus.dts
@@ -87,7 +87,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		checkstop {
+		event-checkstop {
 			label = "checkstop";
 			gpios = <&gpio ASPEED_GPIO(J, 2) GPIO_ACTIVE_LOW>;
 			linux,code = <ASPEED_GPIO(J, 2)>;
diff --git a/arch/arm/boot/dts/aspeed-bmc-opp-swift.dts b/arch/arm/boot/dts/aspeed-bmc-opp-swift.dts
index 4816486c0c9e..bbf864f84d37 100644
--- a/arch/arm/boot/dts/aspeed-bmc-opp-swift.dts
+++ b/arch/arm/boot/dts/aspeed-bmc-opp-swift.dts
@@ -38,37 +38,37 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		air-water {
+		event-air-water {
 			label = "air-water";
 			gpios = <&gpio ASPEED_GPIO(B, 5) GPIO_ACTIVE_LOW>;
 			linux,code = <ASPEED_GPIO(B, 5)>;
 		};
 
-		checkstop {
+		event-checkstop {
 			label = "checkstop";
 			gpios = <&gpio ASPEED_GPIO(J, 2) GPIO_ACTIVE_LOW>;
 			linux,code = <ASPEED_GPIO(J, 2)>;
 		};
 
-		ps0-presence {
+		event-ps0-presence {
 			label = "ps0-presence";
 			gpios = <&gpio ASPEED_GPIO(R, 7) GPIO_ACTIVE_LOW>;
 			linux,code = <ASPEED_GPIO(R, 7)>;
 		};
 
-		ps1-presence {
+		event-ps1-presence {
 			label = "ps1-presence";
 			gpios = <&gpio ASPEED_GPIO(N, 0) GPIO_ACTIVE_LOW>;
 			linux,code = <ASPEED_GPIO(N, 0)>;
 		};
 
-		oppanel-presence {
+		event-oppanel-presence {
 			label = "oppanel-presence";
 			gpios = <&gpio ASPEED_GPIO(A, 7) GPIO_ACTIVE_LOW>;
 			linux,code = <ASPEED_GPIO(A, 7)>;
 		};
 
-		opencapi-riser-presence {
+		event-opencapi-riser-presence {
 			label = "opencapi-riser-presence";
 			gpios = <&gpio ASPEED_GPIO(I, 0) GPIO_ACTIVE_LOW>;
 			linux,code = <ASPEED_GPIO(I, 0)>;
@@ -84,55 +84,55 @@
 		compatible = "gpio-keys-polled";
 		poll-interval = <1000>;
 
-		scm0-presence {
+		event-scm0-presence {
 			label = "scm0-presence";
 			gpios = <&pca9552 6 GPIO_ACTIVE_LOW>;
 			linux,code = <6>;
 		};
 
-		scm1-presence {
+		event-scm1-presence {
 			label = "scm1-presence";
 			gpios = <&pca9552 7 GPIO_ACTIVE_LOW>;
 			linux,code = <7>;
 		};
 
-		cpu0vrm-presence {
+		event-cpu0vrm-presence {
 			label = "cpu0vrm-presence";
 			gpios = <&pca9552 12 GPIO_ACTIVE_LOW>;
 			linux,code = <12>;
 		};
 
-		cpu1vrm-presence {
+		event-cpu1vrm-presence {
 			label = "cpu1vrm-presence";
 			gpios = <&pca9552 13 GPIO_ACTIVE_LOW>;
 			linux,code = <13>;
 		};
 
-		fan0-presence {
+		event-fan0-presence {
 			label = "fan0-presence";
 			gpios = <&pca0 5 GPIO_ACTIVE_LOW>;
 			linux,code = <5>;
 		};
 
-		fan1-presence {
+		event-fan1-presence {
 			label = "fan1-presence";
 			gpios = <&pca0 6 GPIO_ACTIVE_LOW>;
 			linux,code = <6>;
 		};
 
-		fan2-presence {
+		event-fan2-presence {
 			label = "fan2-presence";
 			gpios = <&pca0 7 GPIO_ACTIVE_LOW>;
 			linux,code = <7>;
 		};
 
-		fan3-presence {
+		event-fan3-presence {
 			label = "fan3-presence";
 			gpios = <&pca0 8 GPIO_ACTIVE_LOW>;
 			linux,code = <8>;
 		};
 
-		fanboost-presence {
+		event-fanboost-presence {
 			label = "fanboost-presence";
 			gpios = <&pca0 9 GPIO_ACTIVE_LOW>;
 			linux,code = <9>;
diff --git a/arch/arm/boot/dts/aspeed-bmc-opp-tacoma.dts b/arch/arm/boot/dts/aspeed-bmc-opp-tacoma.dts
index e39f310d55eb..3f6010ef2b86 100644
--- a/arch/arm/boot/dts/aspeed-bmc-opp-tacoma.dts
+++ b/arch/arm/boot/dts/aspeed-bmc-opp-tacoma.dts
@@ -50,13 +50,13 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		ps0-presence {
+		event-ps0-presence {
 			label = "ps0-presence";
 			gpios = <&gpio0 ASPEED_GPIO(H, 3) GPIO_ACTIVE_LOW>;
 			linux,code = <ASPEED_GPIO(H, 3)>;
 		};
 
-		ps1-presence {
+		event-ps1-presence {
 			label = "ps1-presence";
 			gpios = <&gpio0 ASPEED_GPIO(E, 5) GPIO_ACTIVE_LOW>;
 			linux,code = <ASPEED_GPIO(E, 5)>;
@@ -65,29 +65,27 @@
 
 	gpio-keys-polled {
 		compatible = "gpio-keys-polled";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		poll-interval = <1000>;
 
-		fan0-presence {
+		event-fan0-presence {
 			label = "fan0-presence";
 			gpios = <&pca0 4 GPIO_ACTIVE_LOW>;
 			linux,code = <4>;
 		};
 
-		fan1-presence {
+		event-fan1-presence {
 			label = "fan1-presence";
 			gpios = <&pca0 5 GPIO_ACTIVE_LOW>;
 			linux,code = <5>;
 		};
 
-		fan2-presence {
+		event-fan2-presence {
 			label = "fan2-presence";
 			gpios = <&pca0 6 GPIO_ACTIVE_LOW>;
 			linux,code = <6>;
 		};
 
-		fan3-presence {
+		event-fan3-presence {
 			label = "fan3-presence";
 			gpios = <&pca0 7 GPIO_ACTIVE_LOW>;
 			linux,code = <7>;
@@ -197,7 +195,6 @@
 
 	fsi-routing-gpios = <&gpio0 ASPEED_GPIO(Q, 7) GPIO_ACTIVE_HIGH>;
 	fsi-mux-gpios = <&gpio0 ASPEED_GPIO(B, 0) GPIO_ACTIVE_HIGH>;
-	cfam-reset-gpios = <&gpio0 ASPEED_GPIO(Q, 0) GPIO_ACTIVE_LOW>;
 
 	cfam@0,0 {
 		reg = <0 0>;
@@ -877,3 +874,14 @@
 	status = "okay";
 	memory-region = <&vga_memory>;
 };
+
+&kcs2 {
+	status = "okay";
+	aspeed,lpc-io-reg = <0xca8 0xcac>;
+};
+
+&kcs3 {
+	status = "okay";
+	aspeed,lpc-io-reg = <0xca2>;
+	aspeed,lpc-interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+};
diff --git a/arch/arm/boot/dts/aspeed-bmc-opp-vesnin.dts b/arch/arm/boot/dts/aspeed-bmc-opp-vesnin.dts
index 328ef472c479..8a7fb55ab489 100644
--- a/arch/arm/boot/dts/aspeed-bmc-opp-vesnin.dts
+++ b/arch/arm/boot/dts/aspeed-bmc-opp-vesnin.dts
@@ -63,13 +63,13 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		button_checkstop {
+		event-checkstop {
 			label = "checkstop";
 			linux,code = <74>;
 			gpios = <&gpio ASPEED_GPIO(P, 5) GPIO_ACTIVE_LOW>;
 		};
 
-		button_identify {
+		event-identify {
 			label = "identify";
 			linux,code = <152>;
 			gpios = <&gpio ASPEED_GPIO(O, 7) GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/aspeed-bmc-opp-witherspoon.dts b/arch/arm/boot/dts/aspeed-bmc-opp-witherspoon.dts
index 230f3584bcab..a20a532fc280 100644
--- a/arch/arm/boot/dts/aspeed-bmc-opp-witherspoon.dts
+++ b/arch/arm/boot/dts/aspeed-bmc-opp-witherspoon.dts
@@ -51,25 +51,25 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		air-water {
+		event-air-water {
 			label = "air-water";
 			gpios = <&gpio ASPEED_GPIO(B, 5) GPIO_ACTIVE_LOW>;
 			linux,code = <ASPEED_GPIO(B, 5)>;
 		};
 
-		checkstop {
+		event-checkstop {
 			label = "checkstop";
 			gpios = <&gpio ASPEED_GPIO(J, 2) GPIO_ACTIVE_LOW>;
 			linux,code = <ASPEED_GPIO(J, 2)>;
 		};
 
-		ps0-presence {
+		event-ps0-presence {
 			label = "ps0-presence";
 			gpios = <&gpio ASPEED_GPIO(P, 7) GPIO_ACTIVE_LOW>;
 			linux,code = <ASPEED_GPIO(P, 7)>;
 		};
 
-		ps1-presence {
+		event-ps1-presence {
 			label = "ps1-presence";
 			gpios = <&gpio ASPEED_GPIO(N, 0) GPIO_ACTIVE_LOW>;
 			linux,code = <ASPEED_GPIO(N, 0)>;
@@ -85,25 +85,25 @@
 		compatible = "gpio-keys-polled";
 		poll-interval = <1000>;
 
-		fan0-presence {
+		event-fan0-presence {
 			label = "fan0-presence";
 			gpios = <&pca0 4 GPIO_ACTIVE_LOW>;
 			linux,code = <4>;
 		};
 
-		fan1-presence {
+		event-fan1-presence {
 			label = "fan1-presence";
 			gpios = <&pca0 5 GPIO_ACTIVE_LOW>;
 			linux,code = <5>;
 		};
 
-		fan2-presence {
+		event-fan2-presence {
 			label = "fan2-presence";
 			gpios = <&pca0 6 GPIO_ACTIVE_LOW>;
 			linux,code = <6>;
 		};
 
-		fan3-presence {
+		event-fan3-presence {
 			label = "fan3-presence";
 			gpios = <&pca0 7 GPIO_ACTIVE_LOW>;
 			linux,code = <7>;
diff --git a/arch/arm/boot/dts/aspeed-bmc-opp-zaius.dts b/arch/arm/boot/dts/aspeed-bmc-opp-zaius.dts
index 7ae4ea0d2931..0cb7b20ff3ab 100644
--- a/arch/arm/boot/dts/aspeed-bmc-opp-zaius.dts
+++ b/arch/arm/boot/dts/aspeed-bmc-opp-zaius.dts
@@ -58,13 +58,13 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		checkstop {
+		event-checkstop {
 			label = "checkstop";
 			gpios = <&gpio ASPEED_GPIO(F, 7) GPIO_ACTIVE_LOW>;
 			linux,code = <ASPEED_GPIO(F, 7)>;
 		};
 
-		pcie-e2b-present{
+		event-pcie-e2b-present{
 			label = "pcie-e2b-present";
 			gpios = <&gpio ASPEED_GPIO(E, 7) GPIO_ACTIVE_LOW>;
 			linux,code = <ASPEED_GPIO(E, 7)>;
diff --git a/arch/arm/boot/dts/aspeed-bmc-portwell-neptune.dts b/arch/arm/boot/dts/aspeed-bmc-portwell-neptune.dts
index 61bc74b423cf..a5e64ccc2b3a 100644
--- a/arch/arm/boot/dts/aspeed-bmc-portwell-neptune.dts
+++ b/arch/arm/boot/dts/aspeed-bmc-portwell-neptune.dts
@@ -24,17 +24,17 @@
 	leds {
 		compatible = "gpio-leds";
 		postcode0 {
-			label="BMC_UP";
+			label = "BMC_UP";
 			gpios = <&gpio ASPEED_GPIO(H, 0) GPIO_ACTIVE_HIGH>;
 			default-state = "on";
 		};
 		postcode1 {
-			label="BMC_HB";
+			label = "BMC_HB";
 			gpios = <&gpio ASPEED_GPIO(H, 1) GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
 		};
 		postcode2 {
-			label="FAULT";
+			label = "FAULT";
 			gpios = <&gpio ASPEED_GPIO(H, 2) GPIO_ACTIVE_HIGH>;
 		};
 		// postcode3-7 are GPIOH3-H7
diff --git a/arch/arm/boot/dts/aspeed-bmc-qcom-dc-scm-v1.dts b/arch/arm/boot/dts/aspeed-bmc-qcom-dc-scm-v1.dts
new file mode 100644
index 000000000000..259ef3f54c5c
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed-bmc-qcom-dc-scm-v1.dts
@@ -0,0 +1,190 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+// Copyright (c) 2021-2022 Qualcomm Innovation Center, Inc. All rights reserved.
+
+/dts-v1/;
+
+#include "aspeed-g6.dtsi"
+
+/ {
+	model = "Qualcomm DC-SCM V1 BMC";
+	compatible = "qcom,dc-scm-v1-bmc", "aspeed,ast2600";
+
+	aliases {
+		serial4 = &uart5;
+	};
+
+	chosen {
+		stdout-path = &uart5;
+		bootargs = "console=ttyS4,115200n8";
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x40000000>;
+	};
+};
+
+&mdio3 {
+	status = "okay";
+
+	ethphy3: ethernet-phy@1 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <1>;
+	};
+};
+
+&mac2 {
+	status = "okay";
+
+	/* Bootloader sets up the MAC to insert delay */
+	phy-mode = "rgmii";
+	phy-handle = <&ethphy3>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rgmii3_default>;
+};
+
+&mac3 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rmii4_default>;
+
+	use-ncsi;
+};
+
+&rtc {
+	status = "okay";
+};
+
+&fmc {
+	status = "okay";
+
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "bmc";
+		spi-max-frequency = <133000000>;
+#include "openbmc-flash-layout-64.dtsi"
+	};
+
+	flash@1 {
+		status = "okay";
+		m25p,fast-read;
+		label = "alt-bmc";
+		spi-max-frequency = <133000000>;
+#include "openbmc-flash-layout-64-alt.dtsi"
+	};
+};
+
+&spi1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_spi1_default>;
+
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "bios";
+		spi-max-frequency = <133000000>;
+	};
+};
+
+&gpio0 {
+	gpio-line-names =
+	/*A0-A7*/	"","","","","","","","",
+	/*B0-B7*/	"BMC_FLASH_MUX_SEL","","","","","","","",
+	/*C0-C7*/	"","","","","","","","",
+	/*D0-D7*/	"","","","","","","","",
+	/*E0-E7*/	"","","","","","","","",
+	/*F0-F7*/	"","","","","","","","",
+	/*G0-G7*/	"","","","","","","","",
+	/*H0-H7*/	"","","","","","","","",
+	/*I0-I7*/	"","","","","","","","",
+	/*J0-J7*/	"","","","","","","","",
+	/*K0-K7*/	"","","","","","","","",
+	/*L0-L7*/	"","","","","","","","",
+	/*M0-M7*/	"","","","","","","","",
+	/*N0-N7*/	"BMC_FWSPI_RST_N","","GPIO_1_BMC_3V3","","","","","",
+	/*O0-O7*/	"JTAG_MUX_A","JTAG_MUX_B","","","","","","",
+	/*P0-P7*/	"","","","","","","","",
+	/*Q0-Q7*/	"","","","","","","","",
+	/*R0-R7*/	"","","","","","","","",
+	/*S0-S7*/	"","","","","","","","",
+	/*T0-T7*/	"","","","","","","","",
+	/*U0-U7*/	"","","","","","","","",
+	/*V0-V7*/	"","","","SCMFPGA_SPARE_GPIO1_3V3",
+			"SCMFPGA_SPARE_GPIO2_3V3","SCMFPGA_SPARE_GPIO3_3V3",
+			"SCMFPGA_SPARE_GPIO4_3V3","SCMFPGA_SPARE_GPIO5_3V3",
+	/*W0-W7*/	"","","","","","","","",
+	/*X0-X7*/	"","","","","","","","",
+	/*Y0-Y7*/	"","","","","","","","",
+	/*Z0-Z7*/	"","","","","","","","",
+	/*AA0-AA7*/	"","","","","","","","",
+	/*AB0-AB7*/	"","","","","","","","",
+	/*AC0-AC7*/	"","","","","","","","";
+};
+
+&gpio1 {
+	gpio-line-names =
+	/*A0-A7*/	"GPI_1_BMC_1V8","","","","","",
+			"SCMFPGA_SPARE_GPIO1_1V8","SCMFPGA_SPARE_GPIO2_1V8",
+	/*B0-B7*/	"SCMFPGA_SPARE_GPIO3_1V8","SCMFPGA_SPARE_GPIO4_1V8",
+			"SCMFPGA_SPARE_GPIO5_1V8","","","","","",
+	/*C0-C7*/	"","","","","","","","",
+	/*D0-D7*/	"","BMC_SPI1_RST_N","BIOS_FLASH_MUX_SEL","",
+			"","TPM2_PIRQ_N","TPM2_RST_N","",
+	/*E0-E7*/	"","","","","","","","";
+};
+
+&i2c2 {
+	status = "okay";
+};
+
+&i2c4 {
+	status = "okay";
+};
+
+&i2c5 {
+	status = "okay";
+};
+
+&i2c6 {
+	status = "okay";
+};
+
+&i2c7 {
+	status = "okay";
+};
+
+&i2c8 {
+	status = "okay";
+};
+
+&i2c9 {
+	status = "okay";
+};
+
+&i2c10 {
+	status = "okay";
+};
+
+&i2c12 {
+	status = "okay";
+};
+
+&i2c13 {
+	status = "okay";
+};
+
+&i2c14 {
+	status = "okay";
+};
+
+&i2c15 {
+	status = "okay";
+};
+
+&vhub {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/aspeed-bmc-quanta-s6q.dts b/arch/arm/boot/dts/aspeed-bmc-quanta-s6q.dts
new file mode 100644
index 000000000000..46cbba6305b8
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed-bmc-quanta-s6q.dts
@@ -0,0 +1,610 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+// Copyright 2022 Quanta Corp.
+/dts-v1/;
+
+#include "aspeed-g6.dtsi"
+#include <dt-bindings/gpio/aspeed-gpio.h>
+#include <dt-bindings/i2c/i2c.h>
+
+/ {
+	model = "Quanta S6Q BMC";
+	compatible = "quanta,s6q-bmc", "aspeed,ast2600";
+
+	aliases {
+		// bus 0
+		i2c20 = &SMB_HOST_DB2000_3V3AUX_SCL;
+		i2c21 = &U12_PCA9546_CH1;
+		i2c22 = &SMB_HOST_DB800_B_SCL;
+		i2c23 = &SMB_HOST_DB800_C_SCL;
+
+		// bus 1
+		i2c24 = &SMB_M2_P0_1V8AUX_SCL;
+		i2c25 = &SMB_M2_P1_1V8AUX_SCL;
+		i2c26 = &SMB_CPU_PIROM_3V3AUX_SCL;
+		i2c27 = &SMB_TEMP_3V3AUX_SCL;
+		i2c28 = &SMB_IPMB_3V3AUX_SSDSB_SCL;
+		i2c29 = &SMB_IPMB_3V3AUX_SCL;
+		i2c31 = &SMB_FB_SCL;
+
+		// bus 1 - Fan board
+		i2c32 = &SMB_IOEXP_SCL;
+		i2c33 = &SMB_PROGRAM_SCL;
+		i2c34 = &SMB_FB_SCL_CH2;
+		i2c35 = &SMB_FAN_SENSE_SCL;
+
+		// bus 6
+		i2c36 = &U197_PCA9546_CH0;
+		i2c37 = &U197_PCA9546_CH1;
+		i2c38 = &U197_PCA9546_CH2;
+		i2c39 = &U197_PCA9546_CH3;
+
+		//bus 7
+		i2c40 = &SMB_OCP_SFF_3V3AUX_SCL; //OCP1
+		i2c41 = &SMB_OCP_LFF_3V3AUX_SCL; //OCP2
+	};
+
+	chosen {
+		stdout-path = &uart5;
+		bootargs = "console=ttyS4,115200n8 earlycon";
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x40000000>;
+	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc0 0>, <&adc0 1>, <&adc0 2>, <&adc0 3>,
+			<&adc0 4>, <&adc0 5>, <&adc0 6>, <&adc0 7>,
+			<&adc1 0>, <&adc1 1>, <&adc1 2>, <&adc1 3>,
+			<&adc1 4>, <&adc1 5>, <&adc1 6>, <&adc1 7>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		BMC_HEARTBEAT_N {
+			label = "BMC_HEARTBEAT_N";
+			gpios = <&gpio0 ASPEED_GPIO(P, 7) GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "heartbeat";
+		};
+
+		BMC_LED_STATUS_AMBER_N {
+			label = "BMC_LED_STATUS_AMBER_N";
+			gpios = <&gpio0 ASPEED_GPIO(S, 6) GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		FM_ID_LED_N {
+			label = "FM_ID_LED_N";
+			gpios = <&gpio0 ASPEED_GPIO(B, 5) GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+	};
+};
+
+&gpio0 {
+	gpio-line-names =
+	/*A0 - A7*/	"", "", "", "", "", "", "", "",
+	/*B0 - B7*/	"", "", "", "", "", "", "", "",
+	/*C0 - C7*/	"", "", "", "", "", "", "", "",
+	/*D0 - D7*/	"", "", "", "", "", "", "", "",
+	/*E0 - E7*/	"", "", "", "", "", "", "", "",
+	/*F0 - F7*/	"PLTRST_N", "", "PWR_DEBUG_N", "", "", "", "", "",
+	/*G0 - G7*/	"", "", "", "", "", "", "", "",
+	/*H0 - H7*/	"", "", "", "", "", "", "", "",
+	/*I0 - I7*/	"", "", "", "", "", "", "", "",
+	/*J0 - J7*/	"", "", "", "", "", "", "", "",
+	/*K0 - K7*/	"", "", "", "", "", "", "", "",
+	/*L0 - L7*/	"", "", "", "", "PREQ_N", "TCK_MUX_SEL", "", "",
+	/*M0 - M7*/	"", "", "", "PWRGD_SYS_PWROK", "", "PRDY_N", "", "",
+	/*N0 - N7*/	"", "", "", "", "", "", "", "",
+	/*O0 - O7*/	"", "", "", "", "", "", "", "",
+	/*P0 - P7*/	"SYS_BMC_PWRBTN_R_N", "SYS_PWRBTN_N", "FM_MB_RST_BTN", "RST_BMC_RSTBTN_OUT_N", "", "", "", "",
+	/*Q0 - Q7*/	"", "", "", "", "", "", "", "",
+	/*R0 - R7*/	"", "", "", "", "", "", "", "",
+	/*S0 - S7*/	"", "", "", "FP_ID_BTN_SCM_N", "", "", "", "",
+	/*T0 - T7*/	"", "", "", "", "", "", "", "",
+	/*U0 - U7*/	"", "", "", "", "", "", "", "",
+	/*V0 - V7*/	"", "", "", "", "", "SMI", "", "",
+	/*W0 - W7*/	"", "", "", "", "", "", "", "",
+	/*X0 - X7*/	"", "", "", "", "", "", "", "",
+	/*Y0 - Y7*/	"", "", "", "", "", "", "", "",
+	/*Z0 - Z7*/	"FM_BMC_READY_N", "", "", "", "", "", "", "",
+	/*AA0 - AA7*/	"", "", "", "", "", "", "", "",
+	/*AB0 - AB7*/	"", "", "", "", "", "", "", "",
+	/*AC0 - AC7*/	"", "", "", "", "", "", "", "";
+};
+
+&sgpiom0 {
+	status = "okay";
+	ngpios = <128>;
+	bus-frequency = <48000>;
+	gpio-line-names =
+	/* SGPIO input lines */
+	/*IOA0-IOA7*/	"","", "SIO_POWER_GOOD","OA1", "XDP_PRST_N","", "","", "FM_SLPS3_PLD_N","", "FM_SLPS4_PLD_N","", "FM_BIOS_POST_CMPLT_BMC_N","", "FM_ADR_TRIGGER_N","OA7",
+	/*IOB0-IOB7*/	"FM_ADR_COMPLETE","", "FM_PMBUS_ALERT_B_EN","", "PSU0_PRESENT_N","", "PSU1_PRESENT_N","", "PSU0_VIN_BUF_GOOD","", "PSU01_VIN_BUF_GOOD","", "PWRGD_PS0_PWROK_R","", "PWRGD_PS1_PWROK_R","",
+	/*IOC0-IOC7*/	"PWRGD_PS_PWROK_PLD_R","", "CHASSIS_INTRUSION","", "BMC_MFG_MODE","", "FM_BMC_EN_DET_R","", "FM_ME_BT_DONE","", "CPU1_PRESENCE","", "CPU2_PRESENCE","", "IRQ_PSYS_CRIT_N","",
+	/*IOD0-IOD7*/	"","", "CPU1_THERMTRIP","", "CPU2_THERMTRIP","", "CPU1_MEM_THERM_EVENT","", "CPU2_MEM_THERM_EVENT","", "CPU1_VRHOT","", "CPU2_VRHOT","", "","",
+	/*IOE0-IOE7*/	"","", "CPU1_MEM_VRHOT","", "CPU2_MEM_VRHOT","", "","", "PCH_BMC_THERMTRIP","", "","", "","", "","",
+	/*IOF0-IOF7*/	"CPU_ERR0","", "CPU_ERR1","", "CPU_ERR2","", "","", "","", "CPU_CATERR","", "","", "","",
+	/*IOG0-IOG7*/	"","", "","", "","", "","", "","", "","", "","", "","",
+	/*IOH0-IOH7*/	"","", "FP_ID_BTN_R1_N","", "FP_RST_BTN_N","", "","", "","", "FP_PWR_BTN_PLD_N_R","", "","", "","",
+	/*IOI0-IOI7*/	"","", "","", "","", "","", "","", "","", "","", "","",
+	/*IOJ0-IOJ7*/	"","", "","", "","", "","", "","", "","", "","", "","",
+	/*IOK0-IOK7*/	"","", "","", "","", "","", "","", "","", "","", "","",
+	/*IOL0-IOL7*/	"","", "","", "","", "","", "","", "","", "","", "","",
+	/*IOM0-IOM7*/	"","", "","", "","", "","", "","", "","", "","", "","",
+	/*ION0-ION7*/	"","BMC_SW_HEARTBEAT_N_R", "","FP_LED_FAULT_N", "","FP_ID_LED_N", "","FM_BMC_RSTBTN_OUT_N", "","FM_THERMTRIP_DLY_LVC1_R_N", "","", "","RST_PCA9548_SENSOR_PLD_N", "","USB_OC1_REAR_N",
+	/*IOO0-IOO7*/	"","IRQ_TPM_SPI_N", "","", "","IRQ_PCH_SCI_WHEA_R_N", "","IRQ_BMC_PCH_NMI_R", "","H_CPU_NMI_LVC1_R_N", "","", "","", "","FM_JTAG_BMC_PLD_MUX_SEL",
+	/*IOP0-IOP7*/	"IP0","OP0", "","", "","", "","", "","", "","", "","", "IP7","OP7";
+};
+
+&adc0 {
+	vref = <2500>;
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc0_default &pinctrl_adc1_default
+		&pinctrl_adc2_default &pinctrl_adc3_default
+		&pinctrl_adc4_default &pinctrl_adc5_default
+		&pinctrl_adc6_default &pinctrl_adc7_default>;
+};
+
+&adc1 {
+	vref = <2500>;
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc8_default &pinctrl_adc9_default
+		&pinctrl_adc10_default &pinctrl_adc11_default
+		&pinctrl_adc12_default &pinctrl_adc13_default
+		&pinctrl_adc14_default &pinctrl_adc15_default>;
+};
+
+&mdio2 {
+	status = "okay";
+
+	ethphy2: ethernet-phy@0 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0>;
+	};
+};
+
+&mac2 {
+	status = "okay";
+
+	phy-mode = "rgmii";
+	phy-handle = <&ethphy2>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rgmii3_default>;
+};
+
+&mac3 {
+	status = "okay";
+
+	phy-mode = "rmii";
+	use-ncsi;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rmii4_default>;
+};
+
+&fmc {
+	status = "okay";
+
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "bmc";
+		spi-max-frequency = <50000000>;
+#include "openbmc-flash-layout-64.dtsi"
+	};
+};
+
+&spi2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_spi2_default &pinctrl_spi2cs1_default
+		&pinctrl_spi2cs2_default>;
+	status = "okay";
+
+	flash@0 {
+		status = "okay";
+		m25p,fast-read;
+		label = "spi2:0";
+		spi-max-frequency = <50000000>;
+	};
+};
+
+&kcs1 {
+	status = "okay";
+	aspeed,lpc-io-reg = <0xCA0>;
+};
+
+&kcs2 {
+	status = "okay";
+	aspeed,lpc-io-reg = <0xCA8>;
+};
+
+&kcs3 {
+	status = "okay";
+	aspeed,lpc-io-reg = <0xCA2>;
+};
+
+&emmc_controller {
+	status = "okay";
+};
+
+&emmc {
+	non-removable;
+	bus-width = <4>;
+	max-frequency = <100000000>;
+};
+
+&vhub {
+	status = "okay";
+};
+
+&lpc_snoop {
+	status = "okay";
+	snoop-ports = <0x80>;
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&uart4 {
+	status = "okay";
+};
+
+&uart5 {
+	status = "okay";
+};
+
+&uart_routing {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	U34_PWR_ADC@48 {
+		compatible = "ti,ads7830";
+		reg = <0x48>;
+	};
+
+	U35_PWR_ADC@4b {
+		compatible = "ti,ads7830";
+		reg = <0x4b>;
+	};
+
+	i2c-switch@70 {
+		compatible = "nxp,pca9546";
+		reg = <0x70>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+
+		SMB_HOST_DB2000_3V3AUX_SCL: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		U12_PCA9546_CH1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+
+		SMB_HOST_DB800_B_SCL: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		SMB_HOST_DB800_C_SCL: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+	};
+};
+
+&i2c1 {
+	status = "okay";
+
+	i2c-switch@59 {
+		compatible = "nxp,pca9848";
+		reg = <0x59>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+
+		SMB_M2_P0_1V8AUX_SCL: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		SMB_M2_P1_1V8AUX_SCL: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+
+		SMB_CPU_PIROM_3V3AUX_SCL: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+		};
+
+		SMB_TEMP_3V3AUX_SCL: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+
+			U163_tmp75@48 {
+				compatible = "ti,tmp75";
+				reg = <0x48>;
+			};
+			U114_tmp75@49 {
+				compatible = "ti,tmp75";
+				reg = <0x49>;
+			};
+		};
+
+		SMB_IPMB_3V3AUX_SSDSB_SCL: i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+
+			U4_tmp75@4c {
+				compatible = "ti,tmp75";
+				reg = <0x4c>;
+			};
+			U73_tmp75@4d {
+				compatible = "ti,tmp75";
+				reg = <0x4d>;
+			};
+		};
+
+		SMB_IPMB_3V3AUX_SCL: i2c@5 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <5>;
+
+			U190_fru@51 {
+				compatible = "atmel,24c128";
+				reg = <0x51>;
+				pagesize = <32>;
+			};
+		};
+
+		SMB_FB_SCL: i2c@7 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <7>;
+
+			i2c-switch@77 {
+				compatible = "nxp,pca9546";
+				reg = <0x77>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				i2c-mux-idle-disconnect;
+
+				SMB_IOEXP_SCL: i2c@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <0>;
+				};
+
+				SMB_PROGRAM_SCL: i2c@1 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <1>;
+				};
+
+				SMB_FB_SCL_CH2: i2c@2 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <2>;
+				};
+
+				SMB_FAN_SENSE_SCL: i2c@3 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <3>;
+
+					Current_Meter_U2@45 {
+						compatible = "ti,ina219";
+						reg = <0x45>;
+						shunt-resistor = <1000>; /* = 1 mOhm */
+					};
+
+					Current_Meter_U3@44 {
+						compatible = "ti,ina219";
+						reg = <0x44>;
+						shunt-resistor = <1000>; /* = 1 mOhm */
+					};
+
+					TEMP_sensor_U2@4b {
+						compatible = "ti,tmp75";
+						reg = <0x4b>;
+					};
+				};
+			};
+		};
+	};
+};
+
+&i2c2 {
+	status = "okay";
+	bus-frequency = <400000>;
+
+	ipmb@10 {
+		compatible = "ipmb-dev";
+		reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
+		i2c-protocol;
+	};
+};
+
+&i2c3 {
+	status = "okay";
+
+	/* MB FRU (U173) @ 0xA2 */
+	mb_fru: mb_fru@51 {
+		compatible = "atmel,24c128";
+		reg = <0x51>;
+		pagesize = <32>;
+	};
+
+	/* FP_U1 Inlet */
+	FP_U1_tmp75@4a {
+		compatible = "ti,tmp75";
+		reg = <0x4a>;
+	};
+
+	FP_U4_fru@52 {
+		compatible = "atmel,24c02";
+		reg = <0x52>;
+		pagesize = <16>;
+	};
+};
+
+&i2c4 {
+	status = "okay";
+};
+
+&i2c5 {
+	status = "okay";
+};
+
+&i2c6 {
+	status = "okay";
+
+	i2c-switch@77 {
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x77>;
+		i2c-mux-idle-disconnect;
+
+		U197_PCA9546_CH0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		U197_PCA9546_CH1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+
+			cpu0_pvccin@60 {
+				compatible = "isil,raa229004";
+				reg = <0x60>;
+			};
+
+			cpu0_pvccinfaon@61 {
+				compatible = "isil,isl69260";
+				reg = <0x61>;
+			};
+
+			cpu0_pvccd_hv@63 {
+				compatible = "isil,isl69260";
+				reg = <0x63>;
+			};
+		};
+
+		U197_PCA9546_CH2: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+
+			cpu1_pvccin@72 {
+				compatible = "isil,raa229004";
+				reg = <0x72>;
+			};
+
+			cpu1_pvccinfaon@74 {
+				compatible = "isil,isl69260";
+				reg = <0x74>;
+			};
+
+			cpu1_pvccd_hv@76 {
+				compatible = "isil,isl69260";
+				reg = <0x76>;
+			};
+		};
+
+		U197_PCA9546_CH3: i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <3>;
+		};
+	};
+};
+
+&i2c7 {
+	status = "okay";
+
+	i2c-switch@75 {
+		compatible = "nxp,pca9546";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x75>;
+		i2c-mux-idle-disconnect;
+
+		SMB_OCP_SFF_3V3AUX_SCL: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+		};
+
+		SMB_OCP_LFF_3V3AUX_SCL: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+		};
+	};
+};
+
+&i2c8 {
+	status = "okay";
+};
+
+&i2c9 {
+	status = "okay";
+};
+
+&i2c11 {
+	status = "okay";
+};
+
+&i2c14 {
+	status = "okay";
+
+	/* SCM FRU (U19) @ 0xA2 */
+	scm_fru: scm_fru@51 {
+		compatible = "atmel,24c128";
+		reg = <0x51>;
+		pagesize = <32>;
+	};
+
+	scm_tmp75_u4@4a {
+		compatible = "ti,tmp75";
+		reg = <0x4a>;
+	};
+};
+
+&i2c15 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/aspeed-bmc-tyan-s7106.dts b/arch/arm/boot/dts/aspeed-bmc-tyan-s7106.dts
index 68f332ee1886..aff27c1d4b06 100644
--- a/arch/arm/boot/dts/aspeed-bmc-tyan-s7106.dts
+++ b/arch/arm/boot/dts/aspeed-bmc-tyan-s7106.dts
@@ -3,6 +3,7 @@
 
 #include "aspeed-g5.dtsi"
 #include <dt-bindings/gpio/aspeed-gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
 
 / {
 	model = "Tyan S7106 BMC";
@@ -127,8 +128,23 @@
 	status = "okay";
 };
 
+&uart_routing {
+	status = "okay";
+};
+
 &vuart {
 	status = "okay";
+
+	/* We enable the VUART here, but leave it in a state that does
+	 * not interfere with the SuperIO. The goal is to have both the
+	 * VUART and the SuperIO available and decide at runtime whether
+	 * the VUART should actually be used. For that reason, configure
+	 * an "invalid" IO address and an IRQ that is not used by the
+	 * BMC.
+	 */
+
+	aspeed,lpc-io-reg = <0xffff>;
+	aspeed,lpc-interrupts = <15 IRQ_TYPE_LEVEL_HIGH>;
 };
 
 &lpc_ctrl {
@@ -213,6 +229,30 @@
 	nct7802@28 {
 		compatible = "nuvoton,nct7802";
 		reg = <0x28>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		channel@0 { /* LTD */
+			reg = <0>;
+		};
+
+		channel@1 { /* RTD1 */
+			reg = <1>;
+			sensor-type = "temperature";
+			temperature-mode = "thermistor";
+		};
+
+		channel@2 { /* RTD2 */
+			reg = <2>;
+			sensor-type = "temperature";
+			temperature-mode = "thermistor";
+		};
+
+		channel@3 { /* RTD3 */
+			reg = <3>;
+			sensor-type = "temperature";
+		};
 	};
 
 	/* Also connected to:
diff --git a/arch/arm/boot/dts/aspeed-bmc-tyan-s8036.dts b/arch/arm/boot/dts/aspeed-bmc-tyan-s8036.dts
new file mode 100644
index 000000000000..708ee78e4b83
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed-bmc-tyan-s8036.dts
@@ -0,0 +1,470 @@
+// SPDX-License-Identifier: GPL-2.0+
+/dts-v1/;
+
+#include "aspeed-g5.dtsi"
+#include <dt-bindings/gpio/aspeed-gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	model = "Tyan S8036 BMC";
+	compatible = "tyan,s8036-bmc", "aspeed,ast2500";
+
+	chosen {
+		stdout-path = &uart5;
+		bootargs = "console=ttyS4,115200 earlycon";
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x20000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		p2a_memory: region@987f0000 {
+			no-map;
+			reg = <0x987f0000 0x00010000>; /* 64KB */
+		};
+
+		vga_memory: framebuffer@9f000000 {
+			no-map;
+			reg = <0x9f000000 0x01000000>; /* 16M */
+		};
+
+		gfx_memory: framebuffer {
+			size = <0x01000000>; /* 16M */
+			alignment = <0x01000000>;
+			compatible = "shared-dma-pool";
+			reusable;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		identify {
+			gpios = <&gpio ASPEED_GPIO(A, 2) GPIO_ACTIVE_LOW>;
+		};
+
+		heartbeat {
+			gpios = <&gpio ASPEED_GPIO(E, 7) GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc 0>, <&adc 1>, <&adc 2>, <&adc 3>,
+			<&adc 4>, <&adc 5>, <&adc 6>, <&adc 7>,
+			<&adc 8>, <&adc 9>, <&adc 10>, <&adc 11>,
+			<&adc 12>, <&adc 13>, <&adc 14>;
+	};
+
+	iio-hwmon-battery {
+		compatible = "iio-hwmon";
+		io-channels = <&adc 15>;
+	};
+};
+
+&fmc {
+	status = "okay";
+	flash@0 {
+		label = "bmc";
+		status = "okay";
+		m25p,fast-read;
+#include "openbmc-flash-layout.dtsi"
+	};
+};
+
+&spi1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_spi1_default>;
+
+	flash@0 {
+		status = "okay";
+		label = "pnor";
+		m25p,fast-read;
+	};
+};
+
+&uart1 {
+	/* Rear RS-232 connector */
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_txd1_default
+			&pinctrl_rxd1_default>;
+};
+
+&uart2 {
+	/* RS-232 connector on header */
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_txd2_default
+			&pinctrl_rxd2_default>;
+};
+
+&uart3 {
+	/* Alternative to vuart to internally connect (route) to uart1
+	 * when vuart cannot be used due to BIOS limitations.
+	 */
+	status = "okay";
+};
+
+&uart4 {
+	/* Alternative to vuart to internally connect (route) to the
+	 * external port usually used by uart1 when vuart cannot be
+	 * used due to BIOS limitations.
+	 */
+	status = "okay";
+};
+
+&uart5 {
+	/* BMC "debug" (console) UART; connected to RS-232 connector
+	 * on header; selectable via jumpers as alternative to uart2
+	 */
+	status = "okay";
+};
+
+&uart_routing {
+	status = "okay";
+};
+
+&vuart {
+	status = "okay";
+
+	/* We enable the VUART here, but leave it in a state that does
+	 * not interfere with the SuperIO. The goal is to have both the
+	 * VUART and the SuperIO available and decide at runtime whether
+	 * the VUART should actually be used. For that reason, configure
+	 * an "invalid" IO address and an IRQ that is not used by the
+	 * BMC.
+	 */
+	aspeed,lpc-io-reg = <0xffff>;
+	aspeed,lpc-interrupts = <15 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&lpc_ctrl {
+	status = "okay";
+};
+
+&p2a {
+	status = "okay";
+	memory-region = <&p2a_memory>;
+};
+
+&lpc_snoop {
+	status = "okay";
+	snoop-ports = <0x80>;
+};
+
+&adc {
+	status = "okay";
+};
+
+&vhub {
+	status = "okay";
+};
+
+&pwm_tacho {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm0_default
+			&pinctrl_pwm1_default
+			&pinctrl_pwm3_default
+			&pinctrl_pwm4_default>;
+
+	/* CPU fan */
+	fan@0 {
+		reg = <0x00>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x00>;
+	};
+
+	/* PWM group for chassis fans #1, #2, #3 and #4 */
+	fan@2 {
+		reg = <0x03>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x02>;
+	};
+
+	fan@3 {
+		reg = <0x03>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x03>;
+	};
+
+	fan@4 {
+		reg = <0x03>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x04>;
+	};
+
+	fan@5 {
+		reg = <0x03>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x05>;
+	};
+
+	/* PWM group for chassis fans #5 and #6  */
+	fan@6 {
+		reg = <0x04>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x06>;
+	};
+
+	fan@7 {
+		reg = <0x04>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x07>;
+	};
+};
+
+&i2c0 {
+	/* Directly connected to Sideband-Temperature Sensor Interface (APML) */
+	status = "okay";
+};
+
+&i2c1 {
+	/* Directly connected to IPMB HDR. */
+	status = "okay";
+};
+
+&i2c2 {
+	status = "okay";
+
+	/* BMC EEPROM, incl. mainboard FRU */
+	eeprom@50 {
+		compatible = "atmel,24c256";
+		reg = <0x50>;
+	};
+	/* Also connected to:
+	 * - BCM5720
+	 * - FPGA
+	 * - FAN HDR
+	 * - FPIO HDR
+	 */
+};
+
+&i2c3 {
+	status = "okay";
+
+	/* PSU1 FRU @ 0xA0 */
+	eeprom@50 {
+		compatible = "atmel,24c02";
+		reg = <0x50>;
+	};
+
+	/* PSU2 FRU @ 0xA2 */
+	eeprom@51 {
+		compatible = "atmel,24c02";
+		reg = <0x51>;
+	};
+
+	/* PSU1 @ 0xB0 */
+	power-supply@58 {
+		compatible = "pmbus";
+		reg = <0x58>;
+	};
+
+	/* PSU2 @ 0xB2 */
+	power-supply@59 {
+		compatible = "pmbus";
+		reg = <0x59>;
+	};
+
+};
+
+&i2c4 {
+	status = "okay";
+};
+
+&i2c5 {
+	status = "okay";
+	/* Hardware monitor with temperature sensors */
+	nct7802@28 {
+		compatible = "nuvoton,nct7802";
+		reg = <0x28>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		channel@0 { /* LTD */
+			reg = <0>;
+			status = "okay";
+		};
+
+		channel@1 { /* RTD1 */
+			reg = <1>;
+			status = "okay";
+			sensor-type = "temperature";
+			temperature-mode = "thermistor";
+		};
+
+		channel@2 { /* RTD2 */
+			reg = <2>;
+			status = "okay";
+			sensor-type = "temperature";
+			temperature-mode = "thermistor";
+		};
+
+		channel@3 { /* RTD3 */
+			reg = <3>;
+			status = "okay";
+			sensor-type = "temperature";
+		};
+	};
+
+	/* Also connected to:
+	 * - PCA9544
+	 * - CLK BUFF
+	 * - OCP FRU
+	 */
+};
+
+&i2c6 {
+	status = "okay";
+	/* Connected to:
+	 * - PCA9548 @0xE0
+	 * - PCA9548 @0xE2
+	 * - PCA9544 @0xE4
+	 */
+};
+
+&i2c7 {
+	status = "okay";
+
+	/* Connected to:
+	 * - PCH SMBUS #4
+	 */
+};
+
+&i2c8 {
+	status = "okay";
+
+	/* Not connected */
+};
+
+&mac0 {
+	status = "okay";
+	use-ncsi;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rmii1_default>;
+};
+
+&mac1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rgmii2_default &pinctrl_mdio2_default>;
+};
+
+&ibt {
+	status = "okay";
+};
+
+&kcs1 {
+	status = "okay";
+	aspeed,lpc-io-reg = <0xca8>;
+};
+
+&kcs3 {
+	status = "okay";
+	aspeed,lpc-io-reg = <0xca2>;
+};
+
+/* Enable BMC VGA output to show an early (pre-BIOS) boot screen */
+&gfx {
+	status = "okay";
+	memory-region = <&gfx_memory>;
+};
+
+/* We're following the GPIO naming as defined at
+ * https://github.com/openbmc/docs/blob/master/designs/device-tree-gpio-naming.md.
+ *
+ * Notes on led-identify and id-button:
+ * - A physical button is connected to id-button which
+ *   triggers the clock on a D flip-flop. The /Q output of the
+ *   flip-flop drives its D input.
+ * - The flip-flop's Q output drives led-identify which is
+ *   connected to LEDs.
+ * - With that, every button press toggles the LED between on and off.
+ *
+ * Notes on power-, reset- and nmi- button and control:
+ * - The -button signals can be used to monitor physical buttons.
+ * - The -control signals can be used to actuate the specific
+ *   operation.
+ * - In hardware, the -button signals are connected to the -control
+ *   signals through drivers with the -control signals being
+ *   protected through diodes.
+ */
+&gpio {
+	status = "okay";
+	gpio-line-names =
+	/*A0*/		"",
+	/*A1*/		"",
+	/*A2*/		"led-identify", /* in/out: BMC_CHASSIS_ID_LED_L */
+	/*A3*/		"",
+	/*A4*/		"",
+	/*A5*/		"",
+	/*A6*/		"",
+	/*A7*/		"",
+	/*B0-B7*/	"","","","","","","","",
+	/*C0-C7*/	"","","","","","","","",
+	/*D0*/		"",
+	/*D1*/		"",
+	/*D2*/		"power-chassis-good", /* in: PWR_GOOD_LED -- Check if this is Z3?*/
+	/*D3*/		"platform-reset", /* in: RESET_LED_L */
+	/*D4*/		"",
+	/*D5*/		"",
+	/*D6*/		"",
+	/*D7*/		"",
+	/*E0*/		"power-button", /* in: BMC_SYS_MON_PWR_BTN_L */
+	/*E1*/		"power-chassis-control", /* out: BMC_ASSERT_PWR_BTN */
+	/*E2*/		"reset-button", /* in: BMC_SYS_MOS_RST_BTN_L*/
+	/*E3*/		"reset-control", /* out: BMC_ASSERT_RST_BTN */
+	/*E4*/		"nmi-button", /* in: BMC_SYS_MON_NMI_BTN_L */
+	/*E5*/		"nmi-control", /* out: BMC_ASSERT_NMI_BTN */
+	/*E6*/		"TSI_RESERT",
+	/*E7*/		"led-heartbeat", /* out: BMC_GPIOE7 */
+	/*F0*/		"",
+	/*F1*/		"clear-cmos-control", /* out: BMC_ASSERT_CLR_CMOS_L */
+	/*F2*/		"",
+	/*F3*/		"",
+	/*F4*/		"led-fault", /* out: BMC_HWM_FAULT_LED_L */
+	/*F5*/		"BMC_SYS_FAULT_LED_L",
+	/*F6*/		"BMC_ASSERT_BIOS_WP_L",
+	/*F7*/		"",
+	/*G0-G7*/	"","","","","","","","",
+	/*H0-H7*/	"","","","","","","","",
+	/*I0-I7*/	"","","","","","","","",
+	/*J0-J7*/	"","","","","","","","",
+	/*K0-K7*/	"","","","","","","","",
+	/*L0-L7*/	"","","","","","","","",
+	/*M0-M7*/	"","","","","","","","",
+	/*N0-N7*/	"","","","","","","","",
+	/*O0-O7*/	"","","","","","","","",
+	/*P0-P7*/	"","","","","","","","",
+	/*Q0*/		"",
+	/*Q1*/		"",
+	/*Q2*/		"",
+	/*Q3*/		"",
+	/*Q4*/		"",
+	/*Q5*/		"",
+	/*Q6*/		"id-button", /* in: BMC_CHASSIS_ID_BTN_L */
+	/*Q7*/		"",
+	/*R0-R7*/	"","","","","","","","",
+	/*S0-S7*/	"","","","","","","","",
+	/*T0-T7*/	"","","","","","","","",
+	/*U0-U7*/	"","","","","","","","",
+	/*V0-V7*/	"","","","","","","","",
+	/*W0-W7*/	"","","","","","","","",
+	/*X0-X7*/	"","","","","","","","",
+	/*Y0-Y7*/	"","","","","","","","",
+	/*Z0-Z2*/	"","","",
+	/*Z3*/		"post-complete", /* BMC_SYS_MON_PWROK */
+	/*Z4-Z7*/	"","","","",
+	/*AA0*/		"",
+	/*AA1*/		"",
+	/*AA2*/		"",
+	/*AA3*/		"",
+	/*AA4*/		"",
+	/*AA5*/		"",
+	/*AA6*/		"",
+	/*AA7*/		"BMC_ASSERT_BMC_READY",
+	/*AB0*/		"BMC_SPD_SEL",
+	/*AB1-AB7*/	"","","","","","","";
+};
diff --git a/arch/arm/boot/dts/aspeed-bmc-vegman-n110.dts b/arch/arm/boot/dts/aspeed-bmc-vegman-n110.dts
new file mode 100644
index 000000000000..24319267d550
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed-bmc-vegman-n110.dts
@@ -0,0 +1,149 @@
+// SPDX-License-Identifier: GPL-2.0+
+// Copyright (C) 2021 YADRO
+/dts-v1/;
+
+#include "aspeed-bmc-vegman.dtsi"
+
+/ {
+	model = "YADRO VEGMAN N110 BMC";
+	compatible = "yadro,vegman-n110-bmc", "aspeed,ast2500";
+};
+
+&gpio {
+	status = "okay";
+	gpio-line-names =
+	/*A0-A7*/	"CHASSIS_INTRUSION","CASE_OPEN_FAULT_RST","","","SPEAKER_BMC","FM_FORCE_BMC_UPDATE","","",
+	/*B0-B7*/	"","","","","","","","",
+	/*C0-C7*/	"","","","","","","","",
+	/*D0-D7*/	"","","","","","","","",
+	/*E0-E7*/	"RESET_BUTTON","RESET_OUT","POWER_BUTTON","POWER_OUT","","","","",
+	/*F0-F7*/	"NMI_OUT","PCIE_NIC_ALERT","","","SKT0_FAULT_LED","","RST_RGMII_PHYRST_DNP","",
+	/*G0-G7*/	"CPU_ERR2","CPU_CATERR","PCH_BMC_THERMTRIP","","IRQ_NMI_EVENT","","","",
+	/*H0-H7*/	"PWRGD_P3V3_RISER1","PWRGD_P3V3_RISER2","PWRGD_P3V3_RISER3","","MIO_BIOS_SEL","_SPI_FLASH_HOLD","_SPI_FLASH_WP","FM_240VA_STATUS",
+	/*I0-I7*/	"","","","","","","","",
+	/*J0-J7*/	"","","","","","","","",
+	/*K0-K7*/	"","","","","","","","",
+	/*L0-L7*/	"","","","","","","","",
+	/*M0-M7*/	"","","","","","","","",
+	/*N0-N7*/	"","","","","","","","",
+	/*O0-O7*/	"","","","","","","","_SPI2_BMC_CS_SEL",
+	/*P0-P7*/	"","","","","","","","",
+	/*Q0-Q7*/	"","","","","","","","",
+	/*R0-R7*/	"_SPI_RMM4_LITE_CS","","","","","","","",
+	/*S0-S7*/	"_SPI2_BMC_CS1","","","IRQ_SML0_ALERT_MUX","FP_LED_STATUS_GREEN","FP_LED_STATUS_AMBER","FP_ID_LED","",
+	/*T0-T7*/	"","","","","","","","",
+	/*U0-U7*/	"","","","","","","","",
+	/*V0-V7*/	"","","","","","","","",
+	/*W0-W7*/	"","","","","","","","",
+	/*X0-X7*/	"","","","","","","","",
+	/*Y0-Y7*/	"SIO_S3","SIO_S5","","SIO_ONCONTROL","","","","",
+	/*Z0-Z7*/	"FM_BMC_PWR_BTN","SIO_POWER_GOOD","FM_BMC_PWRBTN_OUT","FM_BMC_PCH_SCI_LPC","","","","",
+	/*AA0-AA7*/	"","IRQ_SML1_PMBUS_ALERT","FM_PVCCIN_CPU0_PWR_IN_ALERT","FM_PVCCIN_CPU1_PWR_IN_ALERT","BMC_SYS_PWR_FAULT","BMC_SYS_PWR_OK","SMI","POST_COMPLETE",
+	/*AB0-AB7*/	"FM_CPU_BMCINIT","NMI_BUTTON","ID_BUTTON","PS_PWROK","","","","",
+	/*AC0-AC7*/	"","","","","","","","";
+};
+
+&sgpio {
+	ngpios = <80>;
+	bus-frequency = <2000000>;
+	status = "okay";
+	/* SGPIO lines. even: input, odd: output */
+	gpio-line-names =
+	/*A0-A7*/	"CPU1_PRESENCE","","CPU1_THERMTRIP","","CPU1_VRHOT","","CPU1_FIVR_FAULT","","CPU1_MEM_ABCD_VRHOT","","CPU1_MEM_EFGH_VRHOT","","","","","",
+	/*B0-B7*/	"CPU1_MISMATCH","","CPU1_MEM_THERM_EVENT","","CPU2_PRESENCE","","CPU2_THERMTRIP","","CPU2_VRHOT","","CPU2_FIVR_FAULT","","CPU2_MEM_ABCD_VRHOT","","CPU2_MEM_EFGH_VRHOT","",
+	/*C0-C7*/	"","","","","CPU2_MISMATCH","","CPU2_MEM_THERM_EVENT","","","","","","","","","",
+	/*D0-D7*/	"","","","","","","","","","","","","","","","",
+	/*E0-E7*/	"","","","","","","","","","","","","","","","",
+	/*F0-F7*/	"SGPIO_PLD_MINOR_REV_BIT0","","SGPIO_PLD_MINOR_REV_BIT1","","SGPIO_PLD_MINOR_REV_BIT2","","SGPIO_PLD_MINOR_REV_BIT3","","SGPIO_PLD_MAJOR_REV_BIT0","","SGPIO_PLD_MAJOR_REV_BIT1","","SGPIO_PLD_MAJOR_REV_BIT2","","SGPIO_PLD_MAJOR_REV_BIT3","",
+	/*G0-G7*/	"MAIN_PLD_MINOR_REV_BIT0","","MAIN_PLD_MINOR_REV_BIT1","","MAIN_PLD_MINOR_REV_BIT2","","MAIN_PLD_MINOR_REV_BIT3","","MAIN_PLD_MAJOR_REV_BIT0","","MAIN_PLD_MAJOR_REV_BIT1","","MAIN_PLD_MAJOR_REV_BIT2","","MAIN_PLD_MAJOR_REV_BIT3","",
+	/*H0-H7*/	"","","","","","","","","","","","","","","","",
+	/*I0-I7*/	"","","","","","","","","","","","","","","","",
+	/*J0-J7*/	"","","","","","","","","","","","","","","","";
+};
+
+&i2c11 {
+	/* SMB_BMC_MGMT_LVC3 */
+	gpio@21 {
+		compatible = "nxp,pcal9535";
+		reg = <0x21>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names =
+		/*IO0.0-0.7*/	"", "", "", "", "", "", "PE_PCH_SCR_CLKREQ", "",
+		/*IO1.0-1.7*/	"", "PE_PCH_MEZ_PRSNT", "PE_PCH_MEZ_PRSNT_", "NIC_4_PE_PRSNT", "NIC_3_PE_PRSNT", "NIC_2_PE_PRSNT", "NIC_1_PE_PRSNT", "";
+	};
+	gpio@27 {
+		compatible = "nxp,pca9698";
+		reg = <0x27>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names =
+		/*IO0.0-0.7*/	"PWRGD_PS_PWROK", "PWRGD_DSW_PWROK", "PWRGD_P5V_AUX", "PWRGD_P3V3_AUX", "PWRGD_P5V", "PWRGD_P3V3", "PWRGD_P1V8_PCH_AUX", "PWRGD_PCH_PVNN_AUX",
+		/*IO1.0-1.7*/	"PWRGD_P1V05_PCH_AUX", "PWRGD_PCH_AUX_VRS", "PWRGD_PVCCIN_CPU0", "PWRGD_PVCCSA_CPU0", "PWRGD_PVCCIO_CPU0", "PWRGD_PVMCP_CPU0", "PWRGD_P1V0_CPU0", "PWRGD_PVDDQ_ABC_CPU0",
+		/*IO2.0-2.7*/	"PWRGD_PVPP_ABC_CPU0", "PWRGD_PVTT_ABC_CPU0", "PWRGD_PVDDQ_DEF_CPU0", "PWRGD_PVPP_DEF_CPU0", "PWRGD_PVTT_DEF_CPU0", "", "", "",
+		/*IO3.0-3.7*/	"", "", "", "", "", "", "", "",
+		/*IO4.0-4.7*/	"", "", "", "", "", "", "", "";
+	};
+};
+
+&i2c13 {
+	/* SMB_PCIE2_STBY_LVC3 */
+	mux-expa@73 {
+		compatible = "nxp,pca9545";
+		reg = <0x73>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+	};
+	mux-sata@71 {
+		compatible = "nxp,pca9543";
+		reg = <0x71>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+	};
+};
+
+&i2c2 {
+	/* SMB_PCIE_STBY_LVC3 */
+	mux-expb@71 {
+		compatible = "nxp,pca9545";
+		reg = <0x71>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+	};
+};
+
+&pwm_tacho {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm0_default &pinctrl_pwm1_default
+			 &pinctrl_pwm2_default &pinctrl_pwm3_default
+			 &pinctrl_pwm4_default &pinctrl_pwm5_default>;
+
+	fan@0 {
+		reg = <0x00>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x00 0x06>;
+	};
+	fan@1 {
+		reg = <0x01>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x01 0x08>;
+	};
+	fan@2 {
+		reg = <0x02>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x02 0x09>;
+	};
+	fan@3 {
+		reg = <0x03>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x03 0x0A>;
+	};
+	fan@4 {
+		reg = <0x04>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x04 0x0B>;
+	};
+	fan@5 {
+		reg = <0x05>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x05>;
+	};
+};
diff --git a/arch/arm/boot/dts/aspeed-bmc-vegman-rx20.dts b/arch/arm/boot/dts/aspeed-bmc-vegman-rx20.dts
new file mode 100644
index 000000000000..ebbb68b55559
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed-bmc-vegman-rx20.dts
@@ -0,0 +1,255 @@
+// SPDX-License-Identifier: GPL-2.0+
+// Copyright (C) 2021 YADRO
+/dts-v1/;
+
+#include "aspeed-bmc-vegman.dtsi"
+
+/ {
+	model = "YADRO VEGMAN Rx20 BMC";
+	compatible = "yadro,vegman-rx20-bmc", "aspeed,ast2500";
+
+	leds {
+		compatible = "gpio-leds";
+
+		temp_alarm {
+			label = "temp:red:status";
+			default-state = "off";
+			gpios = <&gpio ASPEED_GPIO(E, 4) GPIO_ACTIVE_LOW>;
+		};
+
+		temp_ok {
+			label = "temp:green:status";
+			default-state = "off";
+			gpios = <&gpio ASPEED_GPIO(E, 5) GPIO_ACTIVE_LOW>;
+		};
+
+		psu_fault {
+			label = "psu:red:status";
+			default-state = "off";
+			gpios = <&gpio ASPEED_GPIO(E, 6) GPIO_ACTIVE_LOW>;
+		};
+
+		psu_ok {
+			label = "psu:green:status";
+			default-state = "off";
+			gpios = <&gpio ASPEED_GPIO(E, 7) GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&gpio {
+	status = "okay";
+	gpio-line-names =
+	/*A0-A7*/	"CASE_OPEN_DNP","CASE_OPEN_FAULT_RST_DNP","BEZEL_ON_PWR_P3V3","PWM_PWRGD_EXP_EN","SPEAKER_BMC","FM_FORCE_BMC_UPDATE","","",
+	/*B0-B7*/	"","","","","","","","",
+	/*C0-C7*/	"","","","","","","","",
+	/*D0-D7*/	"","","","","","","","",
+	/*E0-E7*/	"RESET_BUTTON","RESET_OUT","POWER_BUTTON","POWER_OUT","LED_TEMP_STATUS_R","LED_TEMP_STATUS_G","LED_PWR_STATUS_R","LED_PWR_STATUS_G",
+	/*F0-F7*/	"NMI_OUT","CPU1_DISABLE_COD","","","SKT0_FAULT_LED_DNP","SKT1_FAULT_LED_DNP","RST_RGMII_PHYRST_DNP","",
+	/*G0-G7*/	"CPU_ERR2","CPU_CATERR","PCH_BMC_THERMTRIP","SPI_BMC_BOOT_HD","IRQ_NMI_EVENT","SPI_BMC_BOOT_WP","SPI_BMC_BOOT_WP1","",
+	/*H0-H7*/	"PWRGD_P3V3_RISER1","PWRGD_P3V3_RISER2","PWRGD_P3V3_RISER3","","MIO_BIOS_SEL","_SPI_FLASH_HOLD","_SPI_FLASH_WP","FM_240VA_STATUS",
+	/*I0-I7*/	"","","","","","","","",
+	/*J0-J7*/	"","","","","","","","",
+	/*K0-K7*/	"","","","","","","","",
+	/*L0-L7*/	"","","","","","","","",
+	/*M0-M7*/	"SEL_FLASH_SOFT","STATUS_SEL_BMC","","","BMC_WDT_P","ID_BUTTON","PS_PWROK","",
+	/*N0-N7*/	"","","","","","","","",
+	/*O0-O7*/	"","","","","","","","",
+	/*P0-P7*/	"","","","","","","SPI_BIOS_ACTIVE_FLASH_SEL","STATUS_SEL_BIOS",
+	/*Q0-Q7*/	"","","","","","","","",
+	/*R0-R7*/	"_SPI_BMC_BOOT_CS1","","","","","","","",
+	/*S0-S7*/	"_SPI2_BMC_CS1","RSR_A_SMBEXP_RST_INT","RSR_B_SMBEXP_RST_INT","IRQ_SML0_ALERT_MUX","FP_LED_STATUS_GREEN","FP_LED_STATUS_AMBER","FP_ID_LED","",
+	/*T0-T7*/	"","","","","","","","",
+	/*U0-U7*/	"","","","","","","","",
+	/*V0-V7*/	"","","","","","","","",
+	/*W0-W7*/	"","","","","","","","",
+	/*X0-X7*/	"","","","","","","","",
+	/*Y0-Y7*/	"SIO_S3","SIO_S5","","SIO_ONCONTROL","","","","",
+	/*Z0-Z7*/	"FM_BMC_PWR_BTN","SIO_POWER_GOOD","FM_BMC_PWRBTN_OUT","FM_BMC_PCH_SCI_LPC","","","","",
+	/*AA0-AA7*/	"CPU_CLK_MUX_SEL","IRQ_SML1_PMBUS_ALERT","FM_PVCCIN_CPU0_PWR_IN_ALERT","FM_PVCCIN_CPU1_PWR_IN_ALERT","BMC_SYS_PWR_FAULT","BMC_SYS_PWR_OK","SMI","POST_COMPLETE",
+	/*AB0-AB7*/	"FM_CPU_BMCINIT","NMI_BUTTON","BMC_WDT_RST1","BMC_WDT_RST2","","","","",
+	/*AC0-AC7*/	"","","","","","","","";
+};
+
+&sgpio {
+	ngpios = <80>;
+	bus-frequency = <2000000>;
+	status = "okay";
+	/* SGPIO lines. even: input, odd: output */
+	gpio-line-names =
+	/*A0-A7*/	"CPU1_PRESENCE","","CPU1_THERMTRIP","","CPU1_VRHOT","","CPU1_FIVR_FAULT","","CPU1_MEM_ABCD_VRHOT","","CPU1_MEM_EFGH_VRHOT","","","","","",
+	/*B0-B7*/	"CPU1_MISMATCH","","CPU1_MEM_THERM_EVENT","","CPU2_PRESENCE","","CPU2_THERMTRIP","","CPU2_VRHOT","","CPU2_FIVR_FAULT","","CPU2_MEM_ABCD_VRHOT","","CPU2_MEM_EFGH_VRHOT","",
+	/*C0-C7*/	"","","","","CPU2_MISMATCH","","CPU2_MEM_THERM_EVENT","","","","","","","","","",
+	/*D0-D7*/	"","","","","","","","","","","","","","","","",
+	/*E0-E7*/	"","","","","","","","","","","","","","","","",
+	/*F0-F7*/	"SGPIO_PLD_MINOR_REV_BIT0","","SGPIO_PLD_MINOR_REV_BIT1","","SGPIO_PLD_MINOR_REV_BIT2","","SGPIO_PLD_MINOR_REV_BIT3","","SGPIO_PLD_MAJOR_REV_BIT0","","SGPIO_PLD_MAJOR_REV_BIT1","","SGPIO_PLD_MAJOR_REV_BIT2","","SGPIO_PLD_MAJOR_REV_BIT3","",
+	/*G0-G7*/	"MAIN_PLD_MINOR_REV_BIT0","","MAIN_PLD_MINOR_REV_BIT1","","MAIN_PLD_MINOR_REV_BIT2","","MAIN_PLD_MINOR_REV_BIT3","","MAIN_PLD_MAJOR_REV_BIT0","","MAIN_PLD_MAJOR_REV_BIT1","","MAIN_PLD_MAJOR_REV_BIT2","","MAIN_PLD_MAJOR_REV_BIT3","",
+	/*H0-H7*/	"","","","","","","","","","","","","","","","",
+	/*I0-I7*/	"","","","","","","","","","","","","","","","",
+	/*J0-J7*/	"","","","","","","","","","","","","","","","";
+};
+
+&i2c11 {
+	/* SMB_BMC_MGMT_LVC3 */
+	gpio@21 {
+		compatible = "nxp,pcal9535";
+		reg = <0x21>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names =
+		/*IO0.0-0.7*/	"ETH3_CLK_REQ", "ETH2_CLK_REQ", "RSR_A_PCIE_X16_2_PRSNT", "RSR_B_PCIE_X16_2_PRSNT", "", "RSR_B_PCIE_X8_3_PRSNT", "RSR_B_PCIE_X8_4_PRSNT", "RSR_B_PCIE_X16_PRSNT_N",
+		/*IO1.0-1.7*/	"RSR_B_PCIE_X8_2_PRSNT", "RSR_B_PCIE_X8_1_PRSNT", "NIC_1_PE_BUF_PRSNT", "RSR_A_PCIE_X16_PRSNT", "RSR_A_PCIE_X8_3_PRSNT", "RSR_A_PCIE_X8_2_PRSNT", "RSR_A_PCIE_X8_1_PRSNT_N", "";
+	};
+	gpio@23 {
+		compatible = "nxp,pcal9535";
+		reg = <0x23>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names =
+		/*IO0.0-0.7*/	"FM_LINK_WIDTH_ID0", "FM_LINK_WIDTH_ID0", "FM_LINK_WIDTH_ID0", "FM_LINK_WIDTH_ID0", "FM_LINK_WIDTH_ID0", "", "", "",
+		/*IO1.0-1.7*/	"", "", "", "", "", "", "", "";
+	};
+	gpio@27 {
+		compatible = "nxp,pca9698";
+		reg = <0x27>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names =
+		/*IO0.0-0.7*/	"PWRGD_PS_PWROK", "PWRGD_DSW_PWROK", "PWRGD_P5V_AUX", "PWRGD_P3V3_AUX", "PWRGD_P5V", "PWRGD_P3V3", "PWRGD_P1V8_PCH_AUX", "PWRGD_PCH_PVNN_AUX",
+		/*IO1.0-1.7*/	"PWRGD_P1V05_PCH_AUX", "PWRGD_PCH_AUX_VRS", "PWRGD_PVCCIN_CPU0", "PWRGD_PVCCSA_CPU0", "PWRGD_PVCCIO_CPU0", "PWRGD_PVMCP_CPU0", "PWRGD_P1V0_CPU0", "PWRGD_PVDDQ_ABC_CPU0",
+		/*IO2.0-2.7*/	"PWRGD_PVPP_ABC_CPU0", "PWRGD_PVTT_ABC_CPU0", "PWRGD_PVDDQ_DEF_CPU0", "PWRGD_PVPP_DEF_CPU0", "PWRGD_PVTT_DEF_CPU0", "PWRGD_PVCCIN_CPU1", "PWRGD_PVCCSA_CPU1", "PWRGD_PVCCIO_CPU1",
+		/*IO3.0-3.7*/	"PWRGD_PVMCP_CPU1", "PWRGD_P1V0_CPU1", "PWRGD_PVDDQ_GHJ_CPU1", "PWRGD_PVPP_GHJ_CPU1", "PWRGD_PVTT_GHJ_CPU1", "PWRGD_PVDDQ_KLM_CPU1", "PWRGD_PVPP_KLM_CPU1", "PWRGD_PVTT_KLM_CPU1",
+		/*IO4.0-4.7*/	"PCH_PWR_RESET_N", "FM_BOARD_SKU_ID0", "FM_BOARD_SKU_ID1", "FM_BOARD_SKU_ID2", "FM_BOARD_SKU_ID3", "FM_BOARD_SKU_ID4", "FM_BOARD_REV_ID0", "FM_BOARD_REV_ID1";
+	};
+	gpio@39 {
+		compatible = "nxp,pca9554";
+		reg = <0x39>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names =
+		/*IO0.0-0.7*/	"FAN_FAULT_0", "FAN_FAULT_1", "FAN_FAULT_2", "FAN_FAULT_3", "FAN_FAULT_4", "FAN_FAULT_5", "FAN_FAULT_6", "";
+	};
+};
+
+&i2c13 {
+	/* SMB_PCIE2_STBY_LVC3 */
+	mux-expa@70 {
+		compatible = "nxp,pca9548";
+		reg = <0x70>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+
+		i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+			rsra-mux@72 {
+				compatible = "nxp,pca9548";
+				reg = <0x72>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				i2c@7 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <7>;
+					at24@50 {
+						compatible = "atmel,24c64";
+						reg = <0x50>;
+						pagesize = <32>;
+						size = <8192>;
+						address-width = <16>;
+					};
+				};
+			};
+		};
+	};
+	mux-sata@71 {
+		compatible = "nxp,pca9543";
+		reg = <0x71>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+	};
+};
+
+&i2c2 {
+	/* SMB_PCIE_STBY_LVC3 */
+	mux-expb@71 {
+		compatible = "nxp,pca9548";
+		reg = <0x71>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+
+		i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			rsrb-mux@72 {
+				compatible = "nxp,pca9548";
+				reg = <0x72>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				i2c@7 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					reg = <7>;
+					at24@50 {
+						compatible = "atmel,24c64";
+						reg = <0x50>;
+						pagesize = <32>;
+						size = <8192>;
+						address-width = <16>;
+					};
+				};
+			};
+			at24@50 {
+				compatible = "atmel,24c64";
+				reg = <0x50>;
+				pagesize = <32>;
+				size = <8192>;
+				address-width = <16>;
+			};
+		};
+	};
+};
+
+&pwm_tacho {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm0_default &pinctrl_pwm1_default
+			 &pinctrl_pwm2_default &pinctrl_pwm3_default
+			 &pinctrl_pwm4_default &pinctrl_pwm5_default
+			 &pinctrl_pwm6_default>;
+
+	fan@0 {
+		reg = <0x00>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x00 0x07>;
+	};
+	fan@1 {
+		reg = <0x01>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x01 0x08>;
+	};
+	fan@2 {
+		reg = <0x02>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x02 0x09>;
+	};
+	fan@3 {
+		reg = <0x03>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x03 0x0A>;
+	};
+	fan@4 {
+		reg = <0x04>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x04 0x0B>;
+	};
+	fan@5 {
+		reg = <0x05>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x05 0x0C>;
+	};
+	fan@6 {
+		reg = <0x06>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x06 0x0D>;
+	};
+};
diff --git a/arch/arm/boot/dts/aspeed-bmc-vegman-sx20.dts b/arch/arm/boot/dts/aspeed-bmc-vegman-sx20.dts
new file mode 100644
index 000000000000..e36ee4704994
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed-bmc-vegman-sx20.dts
@@ -0,0 +1,154 @@
+// SPDX-License-Identifier: GPL-2.0+
+// Copyright (C) 2021 YADRO
+/dts-v1/;
+
+#include "aspeed-bmc-vegman.dtsi"
+
+/ {
+	model = "YADRO VEGMAN Sx20 BMC";
+	compatible = "yadro,vegman-sx20-bmc", "aspeed,ast2500";
+};
+
+&gpio {
+	status = "okay";
+	gpio-line-names =
+	/*A0-A7*/	"CHASSIS_INTRUSION","CASE_OPEN_FAULT_RST","","","SPEAKER_BMC","FM_FORCE_BMC_UPDATE","","",
+	/*B0-B7*/	"","","","","","","","",
+	/*C0-C7*/	"","","","","","","","",
+	/*D0-D7*/	"","","","","","","","",
+	/*E0-E7*/	"RESET_BUTTON","RESET_OUT","POWER_BUTTON","POWER_OUT","","","","",
+	/*F0-F7*/	"NMI_OUT","CPU1_DISABLE_COD","","","SKT0_FAULT_LED","SKT1_FAULT_LED","RST_RGMII_PHYRST_DNP","",
+	/*G0-G7*/	"CPU_ERR2","CPU_CATERR","PCH_BMC_THERMTRIP","","IRQ_NMI_EVENT","","","",
+	/*H0-H7*/	"PWRGD_P3V3_RISER1","PWRGD_P3V3_RISER2","PWRGD_P3V3_RISER3","","MIO_BIOS_SEL","_SPI_FLASH_HOLD","_SPI_FLASH_WP","FM_240VA_STATUS",
+	/*I0-I7*/	"","","","","","","","",
+	/*J0-J7*/	"","","","","","","","",
+	/*K0-K7*/	"","","","","","","","",
+	/*L0-L7*/	"","","","","","","","",
+	/*M0-M7*/	"","","","","BMC_GPU_RISER_ID1","BMC_GPU_RISER_ID0","","",
+	/*N0-N7*/	"","","","","","","","",
+	/*O0-O7*/	"","","","","","","","_SPI2_BMC_CS_SEL",
+	/*P0-P7*/	"","P12V_HDDS_A_EN","P12V_HDDS_B_EN","P5V_HDDS_A_EN","PWRGD_P5V_HDDS_A","P5V_HDDS_B_EN","PWRGD_P5V_HDDS_B","",
+	/*Q0-Q7*/	"","","","","","","","",
+	/*R0-R7*/	"_SPI_RMM4_LITE_CS","","","","","","","",
+	/*S0-S7*/	"_SPI2_BMC_CS1","","","IRQ_SML0_ALERT_MUX","FP_LED_STATUS_GREEN","FP_LED_STATUS_AMBER","FP_ID_LED","",
+	/*T0-T7*/	"","","","","","","","",
+	/*U0-U7*/	"","","","","","","","",
+	/*V0-V7*/	"","","","","","","","",
+	/*W0-W7*/	"","","","","","","","",
+	/*X0-X7*/	"","","","","","","","",
+	/*Y0-Y7*/	"SIO_S3","SIO_S5","","SIO_ONCONTROL","","","","",
+	/*Z0-Z7*/	"FM_BMC_PWR_BTN","SIO_POWER_GOOD","FM_BMC_PWRBTN_OUT","FM_BMC_PCH_SCI_LPC","","","","",
+	/*AA0-AA7*/	"CPU_CLK_MUX_SEL","IRQ_SML1_PMBUS_ALERT","FM_PVCCIN_CPU0_PWR_IN_ALERT","FM_PVCCIN_CPU1_PWR_IN_ALERT","BMC_SYS_PWR_FAULT","BMC_SYS_PWR_OK","SMI","POST_COMPLETE",
+	/*AB0-AB7*/	"FM_CPU_BMCINIT","NMI_BUTTON","ID_BUTTON","PS_PWROK","","","","",
+	/*AC0-AC7*/	"","","","","","","","";
+};
+
+&sgpio {
+	ngpios = <80>;
+	bus-frequency = <2000000>;
+	status = "okay";
+	/* SGPIO lines. even: input, odd: output */
+	gpio-line-names =
+	/*A0-A7*/	"CPU1_PRESENCE","","CPU1_THERMTRIP","","CPU1_VRHOT","","CPU1_FIVR_FAULT","","CPU1_MEM_ABCD_VRHOT","","CPU1_MEM_EFGH_VRHOT","","","","","",
+	/*B0-B7*/	"CPU1_MISMATCH","","CPU1_MEM_THERM_EVENT","","CPU2_PRESENCE","","CPU2_THERMTRIP","","CPU2_VRHOT","","CPU2_FIVR_FAULT","","CPU2_MEM_ABCD_VRHOT","","CPU2_MEM_EFGH_VRHOT","",
+	/*C0-C7*/	"","","","","CPU2_MISMATCH","","CPU2_MEM_THERM_EVENT","","","","","","","","","",
+	/*D0-D7*/	"","","","","","","","","","","","","","","","",
+	/*E0-E7*/	"","","","","","","","","","","","","","","","",
+	/*F0-F7*/	"SGPIO_PLD_MINOR_REV_BIT0","","SGPIO_PLD_MINOR_REV_BIT1","","SGPIO_PLD_MINOR_REV_BIT2","","SGPIO_PLD_MINOR_REV_BIT3","","SGPIO_PLD_MAJOR_REV_BIT0","","SGPIO_PLD_MAJOR_REV_BIT1","","SGPIO_PLD_MAJOR_REV_BIT2","","SGPIO_PLD_MAJOR_REV_BIT3","",
+	/*G0-G7*/	"MAIN_PLD_MINOR_REV_BIT0","","MAIN_PLD_MINOR_REV_BIT1","","MAIN_PLD_MINOR_REV_BIT2","","MAIN_PLD_MINOR_REV_BIT3","","MAIN_PLD_MAJOR_REV_BIT0","","MAIN_PLD_MAJOR_REV_BIT1","","MAIN_PLD_MAJOR_REV_BIT2","","MAIN_PLD_MAJOR_REV_BIT3","",
+	/*H0-H7*/	"","","","","","","","","","","","","","","","",
+	/*I0-I7*/	"","","","","","","","","","","","","","","","",
+	/*J0-J7*/	"","","","","","","","","","","","","","","","";
+};
+
+&i2c11 {
+	/* SMB_BMC_MGMT_LVC3 */
+	gpio@21 {
+		compatible = "nxp,pcal9535";
+		reg = <0x21>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names =
+		/*IO0.0-0.7*/	"", "", "CPU1_PE3_0_SLOT_PRSNT", "", "CPU1_PE1_GPU_PRSNT", "CPU1_PE3_1_SLOT_PRSNT", "PE_PCH_MEZ_PRSNT", "CPU0_PE3_1_SLOT_PRSNT",
+		/*IO1.0-1.7*/	"CPU0_PE1_GPU_PRSNT", "CPU0_PE2_NVME2_PRSNT", "CPU1_PE2_NVME3_PRSNT", "CPU1_PE2_SLOT_PRSNT", "CPU1_PE2_NVME4_PRSNT", "", "CPU0_PE2_NVME1_PRSNT", "CPU0_PE3_0_RAID_PRSNT";
+	};
+	gpio@27 {
+		compatible = "nxp,pca9698";
+		reg = <0x27>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names =
+		/*IO0.0-0.7*/	"PWRGD_PS_PWROK", "PWRGD_DSW_PWROK", "PWRGD_P5V_AUX", "PWRGD_P3V3_AUX", "PWRGD_P5V", "PWRGD_P3V3", "PWRGD_P1V8_PCH_AUX", "PWRGD_PCH_PVNN_AUX",
+		/*IO1.0-1.7*/	"PWRGD_P1V05_PCH_AUX", "PWRGD_PCH_AUX_VRS", "PWRGD_PVCCIN_CPU0", "PWRGD_PVCCSA_CPU0", "PWRGD_PVCCIO_CPU0", "PWRGD_PVMCP_CPU0", "PWRGD_P1V0_CPU0", "PWRGD_PVDDQ_ABC_CPU0",
+		/*IO2.0-2.7*/	"PWRGD_PVPP_ABC_CPU0", "PWRGD_PVTT_ABC_CPU0", "PWRGD_PVDDQ_DEF_CPU0", "PWRGD_PVPP_DEF_CPU0", "PWRGD_PVTT_DEF_CPU0", "PWRGD_PVCCIN_CPU1", "PWRGD_PVCCSA_CPU1", "PWRGD_PVCCIO_CPU1",
+		/*IO3.0-3.7*/	"PWRGD_PVMCP_CPU1", "PWRGD_P1V0_CPU1", "PWRGD_PVDDQ_GHJ_CPU1", "PWRGD_PVPP_GHJ_CPU1", "PWRGD_PVTT_GHJ_CPU1", "PWRGD_PVDDQ_KLM_CPU1", "PWRGD_PVPP_KLM_CPU1", "PWRGD_PVTT_KLM_CPU1",
+		/*IO4.0-4.7*/	"PWRGD_P5V_HDDS_A_R", "PWRGD_P5V_HDDS_B_R", "", "", "", "", "", "";
+	};
+};
+
+&i2c13 {
+	/* SMB_PCIE2_STBY_LVC3 */
+	mux-expa@73 {
+		compatible = "nxp,pca9545";
+		reg = <0x73>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+	};
+	mux-sata@71 {
+		compatible = "nxp,pca9543";
+		reg = <0x71>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+	};
+};
+
+&i2c2 {
+	/* SMB_PCIE_STBY_LVC3 */
+	mux-expb@71 {
+		compatible = "nxp,pca9545";
+		reg = <0x71>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
+	};
+};
+
+&pwm_tacho {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm0_default &pinctrl_pwm1_default
+			 &pinctrl_pwm2_default &pinctrl_pwm3_default
+			 &pinctrl_pwm4_default &pinctrl_pwm5_default
+			 &pinctrl_pwm6_default>;
+
+	fan@0 {
+		reg = <0x00>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x00>;
+	};
+	fan@1 {
+		reg = <0x01>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x01>;
+	};
+	fan@2 {
+		reg = <0x02>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x02>;
+	};
+	fan@3 {
+		reg = <0x03>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x03>;
+	};
+	fan@4 {
+		reg = <0x04>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x04>;
+	};
+	fan@5 {
+		reg = <0x05>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x05>;
+	};
+	fan@6 {
+		reg = <0x06>;
+		aspeed,fan-tach-ch = /bits/ 8 <0x06>;
+	};
+};
diff --git a/arch/arm/boot/dts/aspeed-bmc-vegman.dtsi b/arch/arm/boot/dts/aspeed-bmc-vegman.dtsi
new file mode 100644
index 000000000000..1a5b25b2ea29
--- /dev/null
+++ b/arch/arm/boot/dts/aspeed-bmc-vegman.dtsi
@@ -0,0 +1,311 @@
+// SPDX-License-Identifier: GPL-2.0+
+// Copyright (C) 2021 YADRO
+
+#include "aspeed-g5.dtsi"
+#include <dt-bindings/gpio/aspeed-gpio.h>
+
+/ {
+	aliases {
+		serial4 = &uart5;
+	};
+
+	chosen {
+		stdout-path = &uart5;
+		bootargs = "console=ttyS4,115200 earlyprintk";
+	};
+
+	memory@80000000 {
+		reg = <0x80000000 0x20000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		video_engine_memory: jpegbuffer {
+			size = <0x02000000>;	/* 32M */
+			alignment = <0x01000000>;
+			compatible = "shared-dma-pool";
+			reusable;
+		};
+
+		ramoops@9eff0000{
+			compatible = "ramoops";
+			reg = <0x9eff0000 0x10000>;
+			record-size = <0x2000>;
+			console-size = <0x2000>;
+		};
+	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc 0>, <&adc 1>, <&adc 2>, <&adc 3>,
+			<&adc 4>, <&adc 5>, <&adc 6>, <&adc 7>,
+			<&adc 8>, <&adc 9>, <&adc 10>, <&adc 11>,
+			<&adc 12>, <&adc 13>, <&adc 14>, <&adc 15>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		identify {
+			label = "platform:blue:indicator";
+			linux,default-trigger = "heartbeat";
+			gpios = <&gpio ASPEED_GPIO(S, 6) GPIO_ACTIVE_LOW>;
+		};
+
+		status_amber {
+			label = "platform:red:status";
+			default-state = "off";
+			gpios = <&gpio ASPEED_GPIO(S, 5) GPIO_ACTIVE_LOW>;
+		};
+
+		status_green {
+			label = "platform:green:status";
+			default-state = "off";
+			gpios = <&gpio ASPEED_GPIO(S, 4) GPIO_ACTIVE_LOW>;
+		};
+
+		power_fault {
+			label = "platform:red:power";
+			default-state = "off";
+			gpios = <&gpio ASPEED_GPIO(AA, 4) GPIO_ACTIVE_LOW>;
+		};
+
+		power_ok {
+			label = "platform:green:power";
+			default-state = "off";
+			gpios = <&gpio ASPEED_GPIO(AA, 5) GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	beeper {
+		compatible = "pwm-beeper";
+		pwms = <&timer 5 1000000 0>;
+	};
+};
+
+&fmc {
+	status = "okay";
+	flash@0 {
+		status = "okay";
+		label = "bmc";
+		m25p,fast-read;
+#include "openbmc-flash-layout-64.dtsi"
+	};
+};
+
+&spi2 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_spi2ck_default
+			&pinctrl_spi2miso_default
+			&pinctrl_spi2mosi_default
+			&pinctrl_spi2cs0_default>;
+	flash@0 {
+		status = "okay";
+		label = "bios";
+		m25p,fast-read;
+	};
+};
+
+&mac0 {
+	status = "okay";
+	use-ncsi;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rmii1_default>;
+};
+
+&mac1 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_rgmii2_default &pinctrl_mdio2_default>;
+
+	phy-mode = "rgmii";
+	phy-handle = <&phy>;
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		phy: ethernet-phy@1 {
+			/* KSZ9131 */
+			compatible = "ethernet-phy-id0022.1640";
+			reg = <1>;
+
+			micrel,led-mode = <0>;
+		};
+	};
+};
+
+&vhub {
+	status = "okay";
+};
+
+&adc {
+	status = "okay";
+};
+
+&video {
+	status = "okay";
+	memory-region = <&video_engine_memory>;
+};
+
+&sdmmc {
+	status = "okay";
+};
+
+&sdhci1 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sd2_default>;
+	disable-wp;
+};
+
+&timer {
+	fttmr010,pwm-outputs = <5>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_timer5_default>;
+	#pwm-cells = <3>;
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_txd1_default
+			&pinctrl_rxd1_default
+			&pinctrl_nrts1_default
+			&pinctrl_ndtr1_default
+			&pinctrl_ndsr1_default
+			&pinctrl_ncts1_default
+			&pinctrl_ndcd1_default
+			&pinctrl_nri1_default>;
+};
+
+&uart5 {
+	status = "okay";
+};
+
+&vuart {
+	status = "okay";
+};
+
+&kcs3 {
+	aspeed,lpc-io-reg = <0xCA2>;
+	status = "okay";
+};
+
+&kcs4 {
+	aspeed,lpc-io-reg = <0xCA4>;
+	status = "okay";
+};
+
+&lpc_snoop {
+	snoop-ports = <0x80>;
+	status = "okay";
+};
+
+&uart_routing {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <>;
+};
+
+&uart3 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <>;
+};
+
+&uart4 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <>;
+};
+
+&i2c0 {
+	/* SMB_IPMB_STBY_LVC3 */
+	multi-master;
+	status = "okay";
+};
+
+&i2c1 {
+	/* SMB_CHASSENSOR_STBY_LVC3 */
+	status = "okay";
+};
+
+&i2c2 {
+	/* SMB_PCIE_STBY_LVC3 */
+	status = "okay";
+};
+
+&i2c3 {
+	/* SMB_HOST_STBY_LVC3 */
+	multi-master;
+	status = "okay";
+};
+
+&i2c4 {
+	/* BMC_PMBUS2_STBY */
+	status = "okay";
+};
+
+&i2c5 {
+	/* SMB_SMLINK0_STBY_LVC3 */
+	bus-frequency = <1000000>;
+	multi-master;
+	status = "okay";
+};
+
+&i2c6 {
+	/* SMB_TEMPSENSOR_STBY_LVC3 */
+	multi-master;
+	status = "okay";
+};
+
+&i2c7 {
+	/* SMB_SM_PMB1_SML1_STBY_LVC3 */
+	multi-master;
+	status = "okay";
+};
+
+&i2c9 {
+	/* SMB_BMC_ETH3_LVC3 */
+	status = "okay";
+};
+
+&i2c10 {
+	/* SMB_BMC_ETH2_LVC3 */
+	status = "okay";
+};
+
+&i2c11 {
+	/* SMB_BMC_MGMT_LVC3 */
+	status = "okay";
+
+	at24@50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+		pagesize = <32>;
+		size = <8192>;
+		address-width = <16>;
+	};
+};
+
+&i2c12 {
+	/* SMB_BMC_FAULT_EXP_LVC3 */
+	status = "okay";
+};
+
+&i2c13 {
+	/* SMB_PCIE2_STBY_LVC3 */
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/aspeed-g4.dtsi b/arch/arm/boot/dts/aspeed-g4.dtsi
index b313a1cf5f73..530491ae5eb2 100644
--- a/arch/arm/boot/dts/aspeed-g4.dtsi
+++ b/arch/arm/boot/dts/aspeed-g4.dtsi
@@ -54,8 +54,7 @@
 		ranges;
 
 		fmc: spi@1e620000 {
-			reg = < 0x1e620000 0x94
-				0x20000000 0x10000000 >;
+			reg = <0x1e620000 0x94>, <0x20000000 0x10000000>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 			compatible = "aspeed,ast2400-fmc";
@@ -65,34 +64,42 @@
 			flash@0 {
 				reg = < 0 >;
 				compatible = "jedec,spi-nor";
+				spi-rx-bus-width = <2>;
 				spi-max-frequency = <50000000>;
 				status = "disabled";
 			};
 			flash@1 {
 				reg = < 1 >;
 				compatible = "jedec,spi-nor";
+				spi-rx-bus-width = <2>;
+				spi-max-frequency = <50000000>;
 				status = "disabled";
 			};
 			flash@2 {
 				reg = < 2 >;
 				compatible = "jedec,spi-nor";
+				spi-rx-bus-width = <2>;
+				spi-max-frequency = <50000000>;
 				status = "disabled";
 			};
 			flash@3 {
 				reg = < 3 >;
 				compatible = "jedec,spi-nor";
+				spi-rx-bus-width = <2>;
+				spi-max-frequency = <50000000>;
 				status = "disabled";
 			};
 			flash@4 {
 				reg = < 4 >;
 				compatible = "jedec,spi-nor";
+				spi-rx-bus-width = <2>;
+				spi-max-frequency = <50000000>;
 				status = "disabled";
 			};
 		};
 
 		spi: spi@1e630000 {
-			reg = < 0x1e630000 0x18
-				0x30000000 0x10000000 >;
+			reg = <0x1e630000 0x18>, <0x30000000 0x10000000>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 			compatible = "aspeed,ast2400-spi";
@@ -102,6 +109,7 @@
 				reg = < 0 >;
 				compatible = "jedec,spi-nor";
 				spi-max-frequency = <50000000>;
+				spi-rx-bus-width = <2>;
 				status = "disabled";
 			};
 		};
@@ -381,6 +389,7 @@
 					compatible = "aspeed,ast2400-ibt-bmc";
 					reg = <0x140 0x18>;
 					interrupts = <8>;
+					clocks = <&syscon ASPEED_CLK_GATE_LCLK>;
 					status = "disabled";
 				};
 
@@ -391,6 +400,17 @@
 				};
 			};
 
+			peci0: peci-controller@1e78b000 {
+				compatible = "aspeed,ast2400-peci";
+				reg = <0x1e78b000 0x60>;
+				interrupts = <15>;
+				clocks = <&syscon ASPEED_CLK_GATE_REFCLK>;
+				resets = <&syscon ASPEED_RESET_PECI>;
+				cmd-timeout-ms = <1000>;
+				clock-frequency = <1000000>;
+				status = "disabled";
+			};
+
 			uart2: serial@1e78d000 {
 				compatible = "ns16550a";
 				reg = <0x1e78d000 0x20>;
diff --git a/arch/arm/boot/dts/aspeed-g5.dtsi b/arch/arm/boot/dts/aspeed-g5.dtsi
index c7049454c7cb..04f98d1dbb97 100644
--- a/arch/arm/boot/dts/aspeed-g5.dtsi
+++ b/arch/arm/boot/dts/aspeed-g5.dtsi
@@ -55,8 +55,7 @@
 		ranges;
 
 		fmc: spi@1e620000 {
-			reg = < 0x1e620000 0xc4
-				0x20000000 0x10000000 >;
+			reg = <0x1e620000 0xc4>, <0x20000000 0x10000000>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 			compatible = "aspeed,ast2500-fmc";
@@ -67,25 +66,27 @@
 				reg = < 0 >;
 				compatible = "jedec,spi-nor";
 				spi-max-frequency = <50000000>;
+				spi-rx-bus-width = <2>;
 				status = "disabled";
 			};
 			flash@1 {
 				reg = < 1 >;
 				compatible = "jedec,spi-nor";
 				spi-max-frequency = <50000000>;
+				spi-rx-bus-width = <2>;
 				status = "disabled";
 			};
 			flash@2 {
 				reg = < 2 >;
 				compatible = "jedec,spi-nor";
 				spi-max-frequency = <50000000>;
+				spi-rx-bus-width = <2>;
 				status = "disabled";
 			};
 		};
 
 		spi1: spi@1e630000 {
-			reg = < 0x1e630000 0xc4
-				0x30000000 0x08000000 >;
+			reg = <0x1e630000 0xc4>, <0x30000000 0x08000000>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 			compatible = "aspeed,ast2500-spi";
@@ -95,19 +96,20 @@
 				reg = < 0 >;
 				compatible = "jedec,spi-nor";
 				spi-max-frequency = <50000000>;
+				spi-rx-bus-width = <2>;
 				status = "disabled";
 			};
 			flash@1 {
 				reg = < 1 >;
 				compatible = "jedec,spi-nor";
 				spi-max-frequency = <50000000>;
+				spi-rx-bus-width = <2>;
 				status = "disabled";
 			};
 		};
 
 		spi2: spi@1e631000 {
-			reg = < 0x1e631000 0xc4
-				0x38000000 0x08000000 >;
+			reg = <0x1e631000 0xc4>, <0x38000000 0x08000000>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 			compatible = "aspeed,ast2500-spi";
@@ -117,12 +119,14 @@
 				reg = < 0 >;
 				compatible = "jedec,spi-nor";
 				spi-max-frequency = <50000000>;
+				spi-rx-bus-width = <2>;
 				status = "disabled";
 			};
 			flash@1 {
 				reg = < 1 >;
 				compatible = "jedec,spi-nor";
 				spi-max-frequency = <50000000>;
+				spi-rx-bus-width = <2>;
 				status = "disabled";
 			};
 		};
@@ -258,6 +262,14 @@
 				quality = <100>;
 			};
 
+			hace: crypto@1e6e3000 {
+				compatible = "aspeed,ast2500-hace";
+				reg = <0x1e6e3000 0x100>;
+				interrupts = <4>;
+				clocks = <&syscon ASPEED_CLK_GATE_YCLK>;
+				resets = <&syscon ASPEED_RESET_HACE>;
+			};
+
 			gfx: display@1e6e6000 {
 				compatible = "aspeed,ast2500-gfx", "syscon";
 				reg = <0x1e6e6000 0x1000>;
@@ -446,6 +458,7 @@
 					compatible = "aspeed,ast2500-kcs-bmc-v2";
 					reg = <0x24 0x1>, <0x30 0x1>, <0x3c 0x1>;
 					interrupts = <8>;
+					clocks = <&syscon ASPEED_CLK_GATE_LCLK>;
 					status = "disabled";
 				};
 
@@ -453,6 +466,7 @@
 					compatible = "aspeed,ast2500-kcs-bmc-v2";
 					reg = <0x28 0x1>, <0x34 0x1>, <0x40 0x1>;
 					interrupts = <8>;
+					clocks = <&syscon ASPEED_CLK_GATE_LCLK>;
 					status = "disabled";
 				};
 
@@ -460,6 +474,7 @@
 					compatible = "aspeed,ast2500-kcs-bmc-v2";
 					reg = <0x2c 0x1>, <0x38 0x1>, <0x44 0x1>;
 					interrupts = <8>;
+					clocks = <&syscon ASPEED_CLK_GATE_LCLK>;
 					status = "disabled";
 				};
 
@@ -467,6 +482,7 @@
 					compatible = "aspeed,ast2500-kcs-bmc-v2";
 					reg = <0x114 0x1>, <0x118 0x1>, <0x11c 0x1>;
 					interrupts = <8>;
+					clocks = <&syscon ASPEED_CLK_GATE_LCLK>;
 					status = "disabled";
 				};
 
@@ -507,10 +523,22 @@
 					compatible = "aspeed,ast2500-ibt-bmc";
 					reg = <0x140 0x18>;
 					interrupts = <8>;
+					clocks = <&syscon ASPEED_CLK_GATE_LCLK>;
 					status = "disabled";
 				};
 			};
 
+			peci0: peci-controller@1e78b000 {
+				compatible = "aspeed,ast2500-peci";
+				reg = <0x1e78b000 0x60>;
+				interrupts = <15>;
+				clocks = <&syscon ASPEED_CLK_GATE_REFCLK>;
+				resets = <&syscon ASPEED_RESET_PECI>;
+				cmd-timeout-ms = <1000>;
+				clock-frequency = <1000000>;
+				status = "disabled";
+			};
+
 			uart2: serial@1e78d000 {
 				compatible = "ns16550a";
 				reg = <0x1e78d000 0x20>;
diff --git a/arch/arm/boot/dts/aspeed-g6-pinctrl.dtsi b/arch/arm/boot/dts/aspeed-g6-pinctrl.dtsi
index 6dde51c2aed3..7cd4f075e325 100644
--- a/arch/arm/boot/dts/aspeed-g6-pinctrl.dtsi
+++ b/arch/arm/boot/dts/aspeed-g6-pinctrl.dtsi
@@ -117,9 +117,9 @@
 		groups = "FWSPID";
 	};
 
-	pinctrl_fwqspid_default: fwqspid_default {
-		function = "FWQSPID";
-		groups = "FWQSPID";
+	pinctrl_fwqspi_default: fwqspi_default {
+		function = "FWQSPI";
+		groups = "FWQSPI";
 	};
 
 	pinctrl_fwspiwp_default: fwspiwp_default {
@@ -653,12 +653,12 @@
 	};
 
 	pinctrl_qspi1_default: qspi1_default {
-		function = "QSPI1";
+		function = "SPI1";
 		groups = "QSPI1";
 	};
 
 	pinctrl_qspi2_default: qspi2_default {
-		function = "QSPI2";
+		function = "SPI2";
 		groups = "QSPI2";
 	};
 
diff --git a/arch/arm/boot/dts/aspeed-g6.dtsi b/arch/arm/boot/dts/aspeed-g6.dtsi
index 5106a424f1ce..ebbcfe445d9c 100644
--- a/arch/arm/boot/dts/aspeed-g6.dtsi
+++ b/arch/arm/boot/dts/aspeed-g6.dtsi
@@ -95,8 +95,7 @@
 			};
 
 		fmc: spi@1e620000 {
-			reg = < 0x1e620000 0xc4
-				0x20000000 0x10000000 >;
+			reg = <0x1e620000 0xc4>, <0x20000000 0x10000000>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 			compatible = "aspeed,ast2600-fmc";
@@ -107,25 +106,27 @@
 				reg = < 0 >;
 				compatible = "jedec,spi-nor";
 				spi-max-frequency = <50000000>;
+				spi-rx-bus-width = <2>;
 				status = "disabled";
 			};
 			flash@1 {
 				reg = < 1 >;
 				compatible = "jedec,spi-nor";
 				spi-max-frequency = <50000000>;
+				spi-rx-bus-width = <2>;
 				status = "disabled";
 			};
 			flash@2 {
 				reg = < 2 >;
 				compatible = "jedec,spi-nor";
 				spi-max-frequency = <50000000>;
+				spi-rx-bus-width = <2>;
 				status = "disabled";
 			};
 		};
 
 		spi1: spi@1e630000 {
-			reg = < 0x1e630000 0xc4
-				0x30000000 0x10000000 >;
+			reg = <0x1e630000 0xc4>, <0x30000000 0x10000000>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 			compatible = "aspeed,ast2600-spi";
@@ -135,19 +136,20 @@
 				reg = < 0 >;
 				compatible = "jedec,spi-nor";
 				spi-max-frequency = <50000000>;
+				spi-rx-bus-width = <2>;
 				status = "disabled";
 			};
 			flash@1 {
 				reg = < 1 >;
 				compatible = "jedec,spi-nor";
 				spi-max-frequency = <50000000>;
+				spi-rx-bus-width = <2>;
 				status = "disabled";
 			};
 		};
 
 		spi2: spi@1e631000 {
-			reg = < 0x1e631000 0xc4
-				0x50000000 0x10000000 >;
+			reg = <0x1e631000 0xc4>, <0x50000000 0x10000000>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 			compatible = "aspeed,ast2600-spi";
@@ -157,18 +159,21 @@
 				reg = < 0 >;
 				compatible = "jedec,spi-nor";
 				spi-max-frequency = <50000000>;
+				spi-rx-bus-width = <2>;
 				status = "disabled";
 			};
 			flash@1 {
 				reg = < 1 >;
 				compatible = "jedec,spi-nor";
 				spi-max-frequency = <50000000>;
+				spi-rx-bus-width = <2>;
 				status = "disabled";
 			};
 			flash@2 {
 				reg = < 2 >;
 				compatible = "jedec,spi-nor";
 				spi-max-frequency = <50000000>;
+				spi-rx-bus-width = <2>;
 				status = "disabled";
 			};
 		};
@@ -181,6 +186,7 @@
 			status = "disabled";
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_mdio1_default>;
+			resets = <&syscon ASPEED_RESET_MII>;
 		};
 
 		mdio1: mdio@1e650008 {
@@ -191,6 +197,7 @@
 			status = "disabled";
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_mdio2_default>;
+			resets = <&syscon ASPEED_RESET_MII>;
 		};
 
 		mdio2: mdio@1e650010 {
@@ -201,6 +208,7 @@
 			status = "disabled";
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_mdio3_default>;
+			resets = <&syscon ASPEED_RESET_MII>;
 		};
 
 		mdio3: mdio@1e650018 {
@@ -211,6 +219,7 @@
 			status = "disabled";
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_mdio4_default>;
+			resets = <&syscon ASPEED_RESET_MII>;
 		};
 
 		mac0: ftgmac@1e660000 {
@@ -298,12 +307,30 @@
 			status = "disabled";
 		};
 
+		udc: usb@1e6a2000 {
+			compatible = "aspeed,ast2600-udc";
+			reg = <0x1e6a2000 0x300>;
+			interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&syscon ASPEED_CLK_GATE_USBPORT2CLK>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_usb2bd_default>;
+			status = "disabled";
+		};
+
 		apb {
 			compatible = "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges;
 
+			hace: crypto@1e6d0000 {
+				compatible = "aspeed,ast2600-hace";
+				reg = <0x1e6d0000 0x200>;
+				interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&syscon ASPEED_CLK_GATE_YCLK>;
+				resets = <&syscon ASPEED_RESET_HACE>;
+			};
+
 			syscon: syscon@1e6e2000 {
 				compatible = "aspeed,ast2600-scu", "syscon", "simple-mfd";
 				reg = <0x1e6e2000 0x1000>;
@@ -351,6 +378,17 @@
 				quality = <100>;
 			};
 
+			gfx: display@1e6e6000 {
+				compatible = "aspeed,ast2600-gfx", "syscon";
+				reg = <0x1e6e6000 0x1000>;
+				reg-io-width = <4>;
+				clocks = <&syscon ASPEED_CLK_GATE_D1CLK>;
+				resets = <&syscon ASPEED_RESET_GRAPHICS>;
+				syscon = <&syscon>;
+				status = "disabled";
+				interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+			};
+
 			xdma: xdma@1e6e7000 {
 				compatible = "aspeed,ast2600-xdma";
 				reg = <0x1e6e7000 0x100>;
@@ -384,6 +422,21 @@
 				status = "disabled";
 			};
 
+			sbc: secure-boot-controller@1e6f2000 {
+				compatible = "aspeed,ast2600-sbc";
+				reg = <0x1e6f2000 0x1000>;
+			};
+
+			video: video@1e700000 {
+				compatible = "aspeed,ast2600-video-engine";
+				reg = <0x1e700000 0x1000>;
+				clocks = <&syscon ASPEED_CLK_GATE_VCLK>,
+					 <&syscon ASPEED_CLK_GATE_ECLK>;
+				clock-names = "vclk", "eclk";
+				interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+				status = "disabled";
+			};
+
 			gpio0: gpio@1e780000 {
 				#gpio-cells = <2>;
 				gpio-controller;
@@ -507,6 +560,17 @@
 				status = "disabled";
 			};
 
+			peci0: peci-controller@1e78b000 {
+				compatible = "aspeed,ast2600-peci";
+				reg = <0x1e78b000 0x100>;
+				interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&syscon ASPEED_CLK_GATE_REF0CLK>;
+				resets = <&syscon ASPEED_RESET_PECI>;
+				cmd-timeout-ms = <1000>;
+				clock-frequency = <1000000>;
+				status = "disabled";
+			};
+
 			lpc: lpc@1e789000 {
 				compatible = "aspeed,ast2600-lpc-v2", "simple-mfd", "syscon";
 				reg = <0x1e789000 0x1000>;
@@ -520,6 +584,7 @@
 					compatible = "aspeed,ast2500-kcs-bmc-v2";
 					reg = <0x24 0x1>, <0x30 0x1>, <0x3c 0x1>;
 					interrupts = <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
+					clocks = <&syscon ASPEED_CLK_GATE_LCLK>;
 					kcs_chan = <1>;
 					status = "disabled";
 				};
@@ -528,6 +593,7 @@
 					compatible = "aspeed,ast2500-kcs-bmc-v2";
 					reg = <0x28 0x1>, <0x34 0x1>, <0x40 0x1>;
 					interrupts = <GIC_SPI 139 IRQ_TYPE_LEVEL_HIGH>;
+					clocks = <&syscon ASPEED_CLK_GATE_LCLK>;
 					status = "disabled";
 				};
 
@@ -535,6 +601,7 @@
 					compatible = "aspeed,ast2500-kcs-bmc-v2";
 					reg = <0x2c 0x1>, <0x38 0x1>, <0x44 0x1>;
 					interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
+					clocks = <&syscon ASPEED_CLK_GATE_LCLK>;
 					status = "disabled";
 				};
 
@@ -542,6 +609,7 @@
 					compatible = "aspeed,ast2500-kcs-bmc-v2";
 					reg = <0x114 0x1>, <0x118 0x1>, <0x11c 0x1>;
 					interrupts = <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>;
+					clocks = <&syscon ASPEED_CLK_GATE_LCLK>;
 					status = "disabled";
 				};
 
@@ -581,6 +649,7 @@
 					compatible = "aspeed,ast2600-ibt-bmc";
 					reg = <0x140 0x18>;
 					interrupts = <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>;
+					clocks = <&syscon ASPEED_CLK_GATE_LCLK>;
 					status = "disabled";
 				};
 			};
@@ -695,6 +764,62 @@
 				status = "disabled";
 			};
 
+			uart6: serial@1e790000 {
+				compatible = "ns16550a";
+				reg = <0x1e790000 0x20>;
+				reg-shift = <2>;
+				reg-io-width = <4>;
+				interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&syscon ASPEED_CLK_GATE_UART6CLK>;
+				no-loopback-test;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_uart6_default>;
+
+				status = "disabled";
+			};
+
+			uart7: serial@1e790100 {
+				compatible = "ns16550a";
+				reg = <0x1e790100 0x20>;
+				reg-shift = <2>;
+				reg-io-width = <4>;
+				interrupts = <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&syscon ASPEED_CLK_GATE_UART7CLK>;
+				no-loopback-test;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_uart7_default>;
+
+				status = "disabled";
+			};
+
+			uart8: serial@1e790200 {
+				compatible = "ns16550a";
+				reg = <0x1e790200 0x20>;
+				reg-shift = <2>;
+				reg-io-width = <4>;
+				interrupts = <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&syscon ASPEED_CLK_GATE_UART8CLK>;
+				no-loopback-test;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_uart8_default>;
+
+				status = "disabled";
+			};
+
+			uart9: serial@1e790300 {
+				compatible = "ns16550a";
+				reg = <0x1e790300 0x20>;
+				reg-shift = <2>;
+				reg-io-width = <4>;
+				interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&syscon ASPEED_CLK_GATE_UART9CLK>;
+				no-loopback-test;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_uart9_default>;
+
+				status = "disabled";
+			};
+
 			i2c: bus@1e78a000 {
 				compatible = "simple-bus";
 				#address-cells = <1>;
diff --git a/arch/arm/boot/dts/at91-dvk_su60_somc.dtsi b/arch/arm/boot/dts/at91-dvk_su60_somc.dtsi
index c1c8650dafce..3542ad8a243e 100644
--- a/arch/arm/boot/dts/at91-dvk_su60_somc.dtsi
+++ b/arch/arm/boot/dts/at91-dvk_su60_somc.dtsi
@@ -44,7 +44,7 @@
 	status = "okay";
 
 	/* spi0.0: 4M Flash Macronix MX25R4035FM1IL0 */
-	spi-flash@0 {
+	flash@0 {
 		compatible = "mxicy,mx25u4035", "jedec,spi-nor";
 		spi-max-frequency = <33000000>;
 		reg = <0>;
diff --git a/arch/arm/boot/dts/at91-foxg20.dts b/arch/arm/boot/dts/at91-foxg20.dts
index 7edf057047f8..9dfd5de808d1 100644
--- a/arch/arm/boot/dts/at91-foxg20.dts
+++ b/arch/arm/boot/dts/at91-foxg20.dts
@@ -155,10 +155,10 @@
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
-		btn {
+		button {
 			label = "Button";
 			gpios = <&pioC 4 GPIO_ACTIVE_LOW>;
 			linux,code = <0x103>;
diff --git a/arch/arm/boot/dts/at91-gatwick.dts b/arch/arm/boot/dts/at91-gatwick.dts
index 5a81cab5fc3a..2c718cf84d7b 100644
--- a/arch/arm/boot/dts/at91-gatwick.dts
+++ b/arch/arm/boot/dts/at91-gatwick.dts
@@ -13,7 +13,7 @@
 	model = "Laird Workgroup Bridge 50N - Project Gatwick";
 	compatible = "laird,gatwick", "laird,wb50n", "atmel,sama5d31", "atmel,sama5d3", "atmel,sama5";
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 		autorepeat;
 
diff --git a/arch/arm/boot/dts/at91-kizbox.dts b/arch/arm/boot/dts/at91-kizbox.dts
index 3b8812fcd854..307663b4eec2 100644
--- a/arch/arm/boot/dts/at91-kizbox.dts
+++ b/arch/arm/boot/dts/at91-kizbox.dts
@@ -28,19 +28,17 @@
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 
-		reset {
+		button-reset {
 			label = "PB_RST";
 			gpios = <&pioB 30 GPIO_ACTIVE_HIGH>;
 			linux,code = <0x100>;
 			wakeup-source;
 		};
 
-		user {
+		button-user {
 			label = "PB_USER";
 			gpios = <&pioB 31 GPIO_ACTIVE_HIGH>;
 			linux,code = <0x101>;
diff --git a/arch/arm/boot/dts/at91-kizbox2-common.dtsi b/arch/arm/boot/dts/at91-kizbox2-common.dtsi
index c08834ddf07b..e5e21dff882f 100644
--- a/arch/arm/boot/dts/at91-kizbox2-common.dtsi
+++ b/arch/arm/boot/dts/at91-kizbox2-common.dtsi
@@ -31,26 +31,24 @@
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 
-		prog {
+		button-prog {
 			label = "PB_PROG";
 			gpios = <&pioE 27 GPIO_ACTIVE_LOW>;
 			linux,code = <0x102>;
 			wakeup-source;
 		};
 
-		reset {
+		button-reset {
 			label = "PB_RST";
 			gpios = <&pioE 29 GPIO_ACTIVE_LOW>;
 			linux,code = <0x100>;
 			wakeup-source;
 		};
 
-		user {
+		button-user {
 			label = "PB_USER";
 			gpios = <&pioE 31 GPIO_ACTIVE_HIGH>;
 			linux,code = <0x101>;
diff --git a/arch/arm/boot/dts/at91-kizbox3-hs.dts b/arch/arm/boot/dts/at91-kizbox3-hs.dts
index 2799b2a1f4d2..7075df6549e9 100644
--- a/arch/arm/boot/dts/at91-kizbox3-hs.dts
+++ b/arch/arm/boot/dts/at91-kizbox3-hs.dts
@@ -55,7 +55,7 @@
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 		pinctrl-names = "default" , "default", "default",
 				"default", "default" ;
@@ -68,35 +68,35 @@
 			     &pinctrl_pio_zbe_rst>;
 		pinctrl-4 = <&pinctrl_pio_input>;
 
-		SW1 {
+		switch-1 {
 			label = "SW1";
 			gpios = <&pioA PIN_PA29 GPIO_ACTIVE_LOW>;
 			linux,code = <0x101>;
 			wakeup-source;
 		};
 
-		SW2 {
+		switch-2 {
 			label = "SW2";
 			gpios = <&pioA PIN_PA18 GPIO_ACTIVE_LOW>;
 			linux,code = <0x102>;
 			wakeup-source;
 		};
 
-		SW3 {
+		switch-3 {
 			label = "SW3";
 			gpios = <&pioA PIN_PA22 GPIO_ACTIVE_LOW>;
 			linux,code = <0x103>;
 			wakeup-source;
 		};
 
-		SW7 {
+		switch-7 {
 			label = "SW7";
 			gpios = <&pioA PIN_PA26 GPIO_ACTIVE_LOW>;
 			linux,code = <0x107>;
 			wakeup-source;
 		};
 
-		SW8 {
+		switch-8 {
 			label = "SW8";
 			gpios = <&pioA PIN_PA24 GPIO_ACTIVE_LOW>;
 			linux,code = <0x108>;
@@ -186,7 +186,7 @@
 
 &pioA {
 	pinctrl_key_gpio_default: key_gpio_default {
-		pinmux=  <PIN_PA22__GPIO>,
+		pinmux = <PIN_PA22__GPIO>,
 		<PIN_PA24__GPIO>,
 		<PIN_PA26__GPIO>,
 		<PIN_PA29__GPIO>,
diff --git a/arch/arm/boot/dts/at91-kizboxmini-common.dtsi b/arch/arm/boot/dts/at91-kizboxmini-common.dtsi
index 9c622892c692..42640fe6b6d0 100644
--- a/arch/arm/boot/dts/at91-kizboxmini-common.dtsi
+++ b/arch/arm/boot/dts/at91-kizboxmini-common.dtsi
@@ -36,17 +36,15 @@
 
 	gpio_keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 
-		prog {
+		key-prog {
 			label = "PB_PROG";
 			gpios = <&pioC 17 GPIO_ACTIVE_LOW>;
 			linux,code = <0x102>;
 			wakeup-source;
 		};
 
-		reset {
+		key-reset {
 			label = "PB_RST";
 			gpios = <&pioC 16 GPIO_ACTIVE_LOW>;
 			linux,code = <0x100>;
diff --git a/arch/arm/boot/dts/at91-nattis-2-natte-2.dts b/arch/arm/boot/dts/at91-nattis-2-natte-2.dts
index 4f123477e631..f71377c9b757 100644
--- a/arch/arm/boot/dts/at91-nattis-2-natte-2.dts
+++ b/arch/arm/boot/dts/at91-nattis-2-natte-2.dts
@@ -18,7 +18,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		wakeup {
+		key-wakeup {
 			label = "Wakeup";
 			linux,code = <10>;
 			wakeup-source;
diff --git a/arch/arm/boot/dts/at91-q5xr5.dts b/arch/arm/boot/dts/at91-q5xr5.dts
index 5827383b181b..9cf60b6f695c 100644
--- a/arch/arm/boot/dts/at91-q5xr5.dts
+++ b/arch/arm/boot/dts/at91-q5xr5.dts
@@ -125,7 +125,7 @@
 	cs-gpios = <&pioA 3 GPIO_ACTIVE_HIGH>, <&pioC 11 GPIO_ACTIVE_LOW>, <0>, <0>;
 	status = "okay";
 
-	m25p80@0 {
+	flash@0 {
 		compatible = "jedec,spi-nor";
 		spi-max-frequency = <20000000>;
 		reg = <0>;
@@ -147,12 +147,6 @@
 			reg = <0x8000 0x3E000>;
 		};
 	};
-
-	spidev@1 {
-		compatible = "spidev";
-		spi-max-frequency = <2000000>;
-		reg = <1>;
-	};
 };
 
 &spi1 {
@@ -160,18 +154,6 @@
 	pinctrl-0 = <&pinctrl_spi1 &pinctrl_spi1_npcs0 &pinctrl_spi1_npcs1>;
 	cs-gpios = <&pioB 3 GPIO_ACTIVE_HIGH>, <&pioC 5 GPIO_ACTIVE_LOW>, <0>, <0>;
 	status = "okay";
-
-	spidev@0 {
-		compatible = "spidev";
-		spi-max-frequency = <2000000>;
-		reg = <0>;
-	};
-
-	spidev@1 {
-		compatible = "spidev";
-		spi-max-frequency = <2000000>;
-		reg = <1>;
-	};
 };
 
 &usart0 {
diff --git a/arch/arm/boot/dts/at91-qil_a9260.dts b/arch/arm/boot/dts/at91-qil_a9260.dts
index 969d990767fc..9d26f9996348 100644
--- a/arch/arm/boot/dts/at91-qil_a9260.dts
+++ b/arch/arm/boot/dts/at91-qil_a9260.dts
@@ -198,10 +198,8 @@
 
 	gpio_keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 
-		user_pb {
+		button-user {
 			label = "user_pb";
 			gpios = <&pioB 10 GPIO_ACTIVE_LOW>;
 			linux,code = <28>;
diff --git a/arch/arm/boot/dts/at91-sam9_l9260.dts b/arch/arm/boot/dts/at91-sam9_l9260.dts
index 1e2a28c2f365..2fb51b9aca2a 100644
--- a/arch/arm/boot/dts/at91-sam9_l9260.dts
+++ b/arch/arm/boot/dts/at91-sam9_l9260.dts
@@ -101,7 +101,7 @@
 		nand0: nand@40000000 {
 			nand-bus-width = <8>;
 			nand-ecc-mode = "soft";
-			nand-on-flash-bbt = <1>;
+			nand-on-flash-bbt;
 			status = "okay";
 		};
 
diff --git a/arch/arm/boot/dts/at91-sam9x60ek.dts b/arch/arm/boot/dts/at91-sam9x60ek.dts
index b1068cca4228..4ba52ba11dc6 100644
--- a/arch/arm/boot/dts/at91-sam9x60ek.dts
+++ b/arch/arm/boot/dts/at91-sam9x60ek.dts
@@ -34,58 +34,15 @@
 		};
 	};
 
-	regulators: regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		vdd_1v8: fixed-regulator-vdd_1v8@0 {
-			compatible = "regulator-fixed";
-			regulator-name = "VDD_1V8";
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-			regulator-always-on;
-			status = "okay";
-		};
-
-		vdd_1v5: fixed-regulator-vdd_1v5@1 {
-			compatible = "regulator-fixed";
-			regulator-name = "VDD_1V5";
-			regulator-min-microvolt = <1500000>;
-			regulator-max-microvolt = <1500000>;
-			regulator-always-on;
-			status = "okay";
-		};
-
-		vdd1_3v3: fixed-regulator-vdd1_3v3@2 {
-			compatible = "regulator-fixed";
-			regulator-name = "VDD1_3V3";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-			status = "okay";
-		};
-
-		vdd2_3v3: regulator-fixed-vdd2_3v3@3 {
-			compatible = "regulator-fixed";
-			regulator-name = "VDD2_3V3";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-			status = "okay";
-		};
-	};
-
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_key_gpio_default>;
-		status = "okay";
 
-		sw1 {
+		button-1 {
 			label = "SW1";
 			gpios = <&pioD 18 GPIO_ACTIVE_LOW>;
-			linux,code=<KEY_PROG1>;
+			linux,code = <KEY_PROG1>;
 			wakeup-source;
 		};
 	};
@@ -112,6 +69,42 @@
 			linux,default-trigger = "heartbeat";
 		};
 	};
+
+	vdd_1v8: fixed-regulator-vdd_1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDD_1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
+		status = "okay";
+	};
+
+	vdd_1v15: fixed-regulator-vdd_1v15 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDD_1V15";
+		regulator-min-microvolt = <1150000>;
+		regulator-max-microvolt = <1150000>;
+		regulator-always-on;
+		status = "okay";
+	};
+
+	vdd1_3v3: fixed-regulator-vdd1_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDD1_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		status = "okay";
+	};
+
+	vdd2_3v3: regulator-fixed-vdd2_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDD2_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		status = "okay";
+	};
 };
 
 &adc {
@@ -233,10 +226,9 @@
 		status = "okay";
 
 		eeprom@53 {
-			compatible = "atmel,24c32";
+			compatible = "atmel,24c02";
 			reg = <0x53>;
 			pagesize = <16>;
-			size = <128>;
 			status = "okay";
 		};
 	};
@@ -266,8 +258,9 @@
 	status = "okay";
 
 	uart1: serial@200 {
-		compatible = "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
+		compatible = "microchip,sam9x60-dbgu", "microchip,sam9x60-usart", "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
 		reg = <0x200 0x200>;
+		atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 		interrupts = <14 IRQ_TYPE_LEVEL_HIGH 7>;
 		dmas = <&dma0
 			(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
diff --git a/arch/arm/boot/dts/at91-sama5d27_som1.dtsi b/arch/arm/boot/dts/at91-sama5d27_som1.dtsi
index a4623cc67cc1..8aa9e8dea337 100644
--- a/arch/arm/boot/dts/at91-sama5d27_som1.dtsi
+++ b/arch/arm/boot/dts/at91-sama5d27_som1.dtsi
@@ -15,7 +15,7 @@
 	compatible = "atmel,sama5d27-som1", "atmel,sama5d27", "atmel,sama5d2", "atmel,sama5";
 
 	aliases {
-		i2c0	= &i2c0;
+		i2c0 = &i2c0;
 	};
 
 	clocks {
@@ -83,6 +83,8 @@
 			macb0: ethernet@f8008000 {
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_macb0_default>;
+				#address-cells = <1>;
+				#size-cells = <0>;
 				phy-mode = "rmii";
 
 				ethernet-phy@7 {
diff --git a/arch/arm/boot/dts/at91-sama5d27_som1_ek.dts b/arch/arm/boot/dts/at91-sama5d27_som1_ek.dts
index 08f0d4b995ff..0dc6ca377b0c 100644
--- a/arch/arm/boot/dts/at91-sama5d27_som1_ek.dts
+++ b/arch/arm/boot/dts/at91-sama5d27_som1_ek.dts
@@ -21,8 +21,8 @@
 		serial0 = &uart1;	/* DBGU */
 		serial1 = &uart4;	/* mikro BUS 1 */
 		serial2 = &uart2;	/* mikro BUS 2 */
-		i2c1	= &i2c1;
-		i2c2	= &i2c3;
+		i2c1 = &i2c1;
+		i2c2 = &i2c3;
 	};
 
 	chosen {
@@ -478,13 +478,13 @@
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_key_gpio_default>;
 
-		pb4 {
+		button {
 			label = "USER";
 			gpios = <&pioA PIN_PA29 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_PROG1>;
diff --git a/arch/arm/boot/dts/at91-sama5d27_wlsom1.dtsi b/arch/arm/boot/dts/at91-sama5d27_wlsom1.dtsi
index 21c86171e462..83bcf9fe0152 100644
--- a/arch/arm/boot/dts/at91-sama5d27_wlsom1.dtsi
+++ b/arch/arm/boot/dts/at91-sama5d27_wlsom1.dtsi
@@ -76,8 +76,8 @@
 		regulators {
 			vdd_3v3: VDD_IO {
 				regulator-name = "VDD_IO";
-				regulator-min-microvolt = <1200000>;
-				regulator-max-microvolt = <3700000>;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
 				regulator-initial-mode = <2>;
 				regulator-allowed-modes = <2>, <4>;
 				regulator-always-on;
@@ -95,8 +95,8 @@
 
 			vddio_ddr: VDD_DDR {
 				regulator-name = "VDD_DDR";
-				regulator-min-microvolt = <600000>;
-				regulator-max-microvolt = <1850000>;
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
 				regulator-initial-mode = <2>;
 				regulator-allowed-modes = <2>, <4>;
 				regulator-always-on;
@@ -118,8 +118,8 @@
 
 			vdd_core: VDD_CORE {
 				regulator-name = "VDD_CORE";
-				regulator-min-microvolt = <600000>;
-				regulator-max-microvolt = <1850000>;
+				regulator-min-microvolt = <1250000>;
+				regulator-max-microvolt = <1250000>;
 				regulator-initial-mode = <2>;
 				regulator-allowed-modes = <2>, <4>;
 				regulator-always-on;
@@ -160,8 +160,8 @@
 
 			LDO1 {
 				regulator-name = "LDO1";
-				regulator-min-microvolt = <1200000>;
-				regulator-max-microvolt = <3700000>;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
 				regulator-always-on;
 
 				regulator-state-standby {
@@ -175,9 +175,8 @@
 
 			LDO2 {
 				regulator-name = "LDO2";
-				regulator-min-microvolt = <1200000>;
-				regulator-max-microvolt = <3700000>;
-				regulator-always-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
 
 				regulator-state-standby {
 					regulator-on-in-suspend;
@@ -194,6 +193,8 @@
 &macb0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_macb0_default>;
+	#address-cells = <1>;
+	#size-cells = <0>;
 	phy-mode = "rmii";
 
 	ethernet-phy@0 {
@@ -214,7 +215,7 @@
 	pinctrl-0 = <&pinctrl_qspi1_default>;
 	status = "disabled";
 
-	qspi1_flash: spi_flash@0 {
+	qspi1_flash: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "jedec,spi-nor";
diff --git a/arch/arm/boot/dts/at91-sama5d27_wlsom1_ek.dts b/arch/arm/boot/dts/at91-sama5d27_wlsom1_ek.dts
index c145c4e5ef58..b665ddc6b0de 100644
--- a/arch/arm/boot/dts/at91-sama5d27_wlsom1_ek.dts
+++ b/arch/arm/boot/dts/at91-sama5d27_wlsom1_ek.dts
@@ -19,21 +19,20 @@
 		serial1 = &uart6;	/* BT */
 		serial2 = &uart5;	/* mikro BUS 2 */
 		serial3 = &uart3;	/* mikro BUS 1 */
-		i2c1	= &i2c1;
+		i2c1 = &i2c1;
 	};
 
 	chosen {
 		stdout-path = "serial0:115200n8";
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_key_gpio_default>;
-		status = "okay";
 
-		sw4 {
+		button-1 {
 			label = "USER BUTTON";
 			gpios = <&pioA PIN_PB2 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_PROG1>;
@@ -191,7 +190,7 @@
 &qspi1 {
 	status = "okay";
 
-	qspi1_flash: spi_flash@0 {
+	qspi1_flash: flash@0 {
 		status = "okay";
 	};
 };
diff --git a/arch/arm/boot/dts/at91-sama5d2_icp.dts b/arch/arm/boot/dts/at91-sama5d2_icp.dts
index 806eb1d911d7..dd1dec9d4e07 100644
--- a/arch/arm/boot/dts/at91-sama5d2_icp.dts
+++ b/arch/arm/boot/dts/at91-sama5d2_icp.dts
@@ -24,8 +24,8 @@
 		serial1 = &uart1;	/* mikro BUS 3 */
 		serial3 = &uart3;	/* mikro BUS 2 */
 		serial5 = &uart7;	/* flx2 */
-		i2c0	= &i2c0;
-		i2c1	= &i2c1;
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
 	};
 
 	chosen {
@@ -42,14 +42,13 @@
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_key_gpio_default>;
-		status = "okay";
 
-		sw4 {
+		button-1 {
 			label = "USER_PB1";
 			gpios = <&pioA PIN_PD0 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_PROG1>;
@@ -197,8 +196,8 @@
 			regulators {
 				vdd_io_reg: VDD_IO {
 					regulator-name = "VDD_IO";
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <3700000>;
+					regulator-min-microvolt = <3300000>;
+					regulator-max-microvolt = <3300000>;
 					regulator-initial-mode = <2>;
 					regulator-allowed-modes = <2>, <4>;
 					regulator-always-on;
@@ -216,8 +215,8 @@
 
 				VDD_DDR {
 					regulator-name = "VDD_DDR";
-					regulator-min-microvolt = <600000>;
-					regulator-max-microvolt = <1850000>;
+					regulator-min-microvolt = <1350000>;
+					regulator-max-microvolt = <1350000>;
 					regulator-initial-mode = <2>;
 					regulator-allowed-modes = <2>, <4>;
 					regulator-always-on;
@@ -235,8 +234,8 @@
 
 				VDD_CORE {
 					regulator-name = "VDD_CORE";
-					regulator-min-microvolt = <600000>;
-					regulator-max-microvolt = <1850000>;
+					regulator-min-microvolt = <1250000>;
+					regulator-max-microvolt = <1250000>;
 					regulator-initial-mode = <2>;
 					regulator-allowed-modes = <2>, <4>;
 					regulator-always-on;
@@ -258,7 +257,6 @@
 					regulator-max-microvolt = <1850000>;
 					regulator-initial-mode = <2>;
 					regulator-allowed-modes = <2>, <4>;
-					regulator-always-on;
 
 					regulator-state-standby {
 						regulator-on-in-suspend;
@@ -273,8 +271,8 @@
 
 				LDO1 {
 					regulator-name = "LDO1";
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <3700000>;
+					regulator-min-microvolt = <2500000>;
+					regulator-max-microvolt = <2500000>;
 					regulator-always-on;
 
 					regulator-state-standby {
@@ -288,8 +286,8 @@
 
 				LDO2 {
 					regulator-name = "LDO2";
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <3700000>;
+					regulator-min-microvolt = <3300000>;
+					regulator-max-microvolt = <3300000>;
 					regulator-always-on;
 
 					regulator-state-standby {
@@ -329,21 +327,21 @@
 	status = "okay";
 
 	eeprom@50 {
-		compatible = "atmel,24c32";
+		compatible = "atmel,24c02";
 		reg = <0x50>;
 		pagesize = <16>;
 		status = "okay";
 	};
 
 	eeprom@52 {
-		compatible = "atmel,24c32";
+		compatible = "atmel,24c02";
 		reg = <0x52>;
 		pagesize = <16>;
 		status = "disabled";
 	};
 
 	eeprom@53 {
-		compatible = "atmel,24c32";
+		compatible = "atmel,24c02";
 		reg = <0x53>;
 		pagesize = <16>;
 		status = "disabled";
diff --git a/arch/arm/boot/dts/at91-sama5d2_ptc_ek.dts b/arch/arm/boot/dts/at91-sama5d2_ptc_ek.dts
index 8ed58af01391..76a711b167b0 100644
--- a/arch/arm/boot/dts/at91-sama5d2_ptc_ek.dts
+++ b/arch/arm/boot/dts/at91-sama5d2_ptc_ek.dts
@@ -20,9 +20,9 @@
 
 	aliases {
 		serial0 = &uart0;	/* DBGU */
-		i2c0	= &i2c0;	/* mikroBUS 1 */
-		i2c1	= &i2c1;	/* XPRO EXT1 */
-		i2c2	= &i2c2;
+		i2c0 = &i2c0;	/* mikroBUS 1 */
+		i2c1 = &i2c1;	/* XPRO EXT1 */
+		i2c2 = &i2c2;
 	};
 
 	chosen {
@@ -139,6 +139,8 @@
 			macb0: ethernet@f8008000 {
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_macb0_default &pinctrl_macb0_phy_irq>;
+				#address-cells = <1>;
+				#size-cells = <0>;
 				phy-mode = "rmii";
 				status = "okay";
 
@@ -394,13 +396,13 @@
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_key_gpio_default>;
 
-		bp1 {
+		button-1 {
 			label = "PB_USER";
 			gpios = <&pioA PIN_PA10 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_PROG1>;
diff --git a/arch/arm/boot/dts/at91-sama5d2_xplained.dts b/arch/arm/boot/dts/at91-sama5d2_xplained.dts
index b1e854f658de..85949c24b687 100644
--- a/arch/arm/boot/dts/at91-sama5d2_xplained.dts
+++ b/arch/arm/boot/dts/at91-sama5d2_xplained.dts
@@ -66,7 +66,7 @@
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_sdmmc0_default>;
 			non-removable;
-			mmc-ddr-1_8v;
+			mmc-ddr-3_3v;
 			status = "okay";
 		};
 
@@ -137,7 +137,7 @@
 				pinctrl-0 = <&pinctrl_spi0_default>;
 				status = "okay";
 
-				m25p80@0 {
+				flash@0 {
 					compatible = "atmel,at25df321a";
 					reg = <0>;
 					spi-max-frequency = <50000000>;
@@ -147,6 +147,8 @@
 			macb0: ethernet@f8008000 {
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_macb0_default &pinctrl_macb0_phy_irq>;
+				#address-cells = <1>;
+				#size-cells = <0>;
 				phy-mode = "rmii";
 				status = "okay";
 
@@ -205,10 +207,10 @@
 
 							regulator-state-mem {
 								regulator-on-in-suspend;
-								regulator-suspend-min-microvolt=<1400000>;
-								regulator-suspend-max-microvolt=<1400000>;
+								regulator-suspend-min-microvolt = <1400000>;
+								regulator-suspend-max-microvolt = <1400000>;
 								regulator-changeable-in-suspend;
-								regulator-mode=<ACT8945A_REGULATOR_MODE_LOWPOWER>;
+								regulator-mode = <ACT8945A_REGULATOR_MODE_LOWPOWER>;
 							};
 						};
 
@@ -619,10 +621,9 @@
 						bias-disable;
 					};
 
-					ck_cd_rstn_vddsel {
+					ck_cd_rstn {
 						pinmux = <PIN_PA0__SDMMC0_CK>,
 							 <PIN_PA10__SDMMC0_RSTN>,
-							 <PIN_PA11__SDMMC0_VDDSEL>,
 							 <PIN_PA13__SDMMC0_CD>;
 						bias-disable;
 					};
@@ -704,13 +705,13 @@
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_key_gpio_default>;
 
-		bp1 {
+		button {
 			label = "PB_USER";
 			gpios = <&pioA PIN_PB9 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_PROG1>;
diff --git a/arch/arm/boot/dts/at91-sama5d3_eds.dts b/arch/arm/boot/dts/at91-sama5d3_eds.dts
new file mode 100644
index 000000000000..c287b03d768b
--- /dev/null
+++ b/arch/arm/boot/dts/at91-sama5d3_eds.dts
@@ -0,0 +1,307 @@
+// SPDX-License-Identifier: GPL-2.0+ OR MIT
+/*
+ * at91-sama5d3_eds.dts - Device Tree file for the SAMA5D3 Ethernet
+ *    Development System board.
+ *
+ * Copyright (C) 2022 Microchip Technology Inc. and its subsidiaries
+ *
+ * Author: Jerry Ray <jerry.ray@microchip.com>
+ */
+/dts-v1/;
+#include "sama5d36.dtsi"
+
+/ {
+	model = "SAMA5D3 Ethernet Development System";
+	compatible = "microchip,sama5d3-eds", "atmel,sama5d36",
+		     "atmel,sama5d3", "atmel,sama5";
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_key_gpio>;
+
+		button-3 {
+			label = "PB_USER";
+			gpios = <&pioE 29 GPIO_ACTIVE_LOW>;
+			linux,code = <0x104>;
+			wakeup-source;
+		};
+	};
+
+	memory@20000000 {
+		reg = <0x20000000 0x10000000>;
+	};
+
+	vcc_3v3_reg: regulator-1 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	vcc_2v5_reg: regulator-2 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_2V5";
+		regulator-min-microvolt = <2500000>;
+		regulator-max-microvolt = <2500000>;
+		regulator-always-on;
+		vin-supply = <&vcc_3v3_reg>;
+	};
+
+	vcc_1v8_reg: regulator-3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
+		vin-supply = <&vcc_3v3_reg>;
+	};
+
+	vcc_1v2_reg: regulator-4 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_1V2";
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <1200000>;
+		regulator-always-on;
+	};
+
+	vcc_mmc0_reg: regulator-5 {
+		compatible = "regulator-fixed";
+		regulator-name = "mmc0-card-supply";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_vcc_mmc0_reg_gpio>;
+		gpio = <&pioE 2 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&can0 {
+	status = "okay";
+};
+
+&dbgu {
+	status = "okay";
+};
+
+&ebi {
+	pinctrl-0 = <&pinctrl_ebi_nand_addr>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	nand_controller: nand-controller {
+		status = "okay";
+
+		nand@3 {
+			reg = <0x3 0x0 0x2>;
+			atmel,rb = <0>;
+			nand-bus-width = <8>;
+			nand-ecc-mode = "hw";
+			nand-ecc-strength = <4>;
+			nand-ecc-step-size = <512>;
+			nand-on-flash-bbt;
+			label = "atmel_nand";
+
+			partitions {
+				compatible = "fixed-partitions";
+				#address-cells = <1>;
+				#size-cells = <1>;
+
+				at91bootstrap@0 {
+					label = "at91bootstrap";
+					reg = <0x0 0x40000>;
+				};
+
+				bootloader@40000 {
+					label = "bootloader";
+					reg = <0x40000 0xc0000>;
+				};
+
+				bootloaderenvred@100000 {
+					label = "bootloader env redundant";
+					reg = <0x100000 0x40000>;
+				};
+
+				bootloaderenv@140000 {
+					label = "bootloader env";
+					reg = <0x140000 0x40000>;
+				};
+
+				dtb@180000 {
+					label = "device tree";
+					reg = <0x180000 0x80000>;
+				};
+
+				kernel@200000 {
+					label = "kernel";
+					reg = <0x200000 0x600000>;
+				};
+
+				rootfs@800000 {
+					label = "rootfs";
+					reg = <0x800000 0x0f800000>;
+				};
+			};
+		};
+	};
+};
+
+&i2c0 {
+	pinctrl-0 = <&pinctrl_i2c0_pu>;
+	status = "okay";
+};
+
+&i2c1 {
+	status = "okay";
+};
+
+&i2c2 {
+	pinctrl-0 = <&pinctrl_i2c2_pu>;
+	status = "okay";
+};
+
+&main_xtal {
+	clock-frequency = <12000000>;
+};
+
+&mmc0 {
+	pinctrl-0 = <&pinctrl_mmc0_clk_cmd_dat0 &pinctrl_mmc0_dat1_3
+		     &pinctrl_mmc0_dat4_7 &pinctrl_mmc0_cd>;
+	vmmc-supply = <&vcc_mmc0_reg>;
+	vqmmc-supply = <&vcc_3v3_reg>;
+	status = "okay";
+	slot@0 {
+		reg = <0>;
+		bus-width = <8>;
+		cd-gpios = <&pioE 0 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&pinctrl {
+	board {
+		pinctrl_i2c0_pu: i2c0-pu {
+			atmel,pins =
+				<AT91_PIOA 30 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>,
+				<AT91_PIOA 31 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
+		};
+
+		pinctrl_i2c2_pu: i2c2-pu {
+			atmel,pins =
+				<AT91_PIOA 18 AT91_PERIPH_B AT91_PINCTRL_PULL_UP>,
+				<AT91_PIOA 19 AT91_PERIPH_B AT91_PINCTRL_PULL_UP>;
+		};
+
+		pinctrl_key_gpio: key-gpio-0 {
+			atmel,pins =
+				<AT91_PIOE 29 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;
+		};
+
+		pinctrl_mmc0_cd: mmc0-cd {
+			atmel,pins =
+				<AT91_PIOE 0 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;
+		};
+
+		/* Reserved for reset signal to the RGMII connector. */
+		pinctrl_rgmii_rstn: rgmii-rstn {
+			atmel,pins =
+				<AT91_PIOD 18 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;
+		};
+
+		/* Reserved for an interrupt line from the RMII and RGMII connectors. */
+		pinctrl_spi_irqn: spi-irqn {
+			atmel,pins =
+				<AT91_PIOB 28 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>;
+		};
+
+		pinctrl_spi0_cs: spi0-cs-default {
+			atmel,pins =
+				<AT91_PIOD 13 AT91_PERIPH_GPIO AT91_PINCTRL_NONE
+				 AT91_PIOD 16 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+		};
+
+		pinctrl_spi1_cs: spi1-cs-default {
+			atmel,pins = <AT91_PIOC 25 AT91_PERIPH_GPIO AT91_PINCTRL_NONE
+				      AT91_PIOC 28 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+		};
+
+		pinctrl_usba_vbus: usba-vbus {
+			atmel,pins =
+				<AT91_PIOE 9 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>;
+		};
+
+		pinctrl_usb_default: usb-default {
+			atmel,pins =
+				<AT91_PIOE 3 AT91_PERIPH_GPIO AT91_PINCTRL_NONE
+				 AT91_PIOE 4 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+		};
+
+		/* Reserved for VBUS fault interrupt. */
+		pinctrl_vbusfault_irqn: vbusfault-irqn {
+			atmel,pins =
+				<AT91_PIOE 5 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>;
+		};
+
+		pinctrl_vcc_mmc0_reg_gpio: vcc-mmc0-reg-gpio-default {
+			atmel,pins = <AT91_PIOE 2 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP>;
+		};
+	};
+};
+
+&slow_xtal {
+	clock-frequency = <32768>;
+};
+
+&spi0 {
+	pinctrl-names = "default", "cs";
+	pinctrl-1 = <&pinctrl_spi0_cs>;
+	cs-gpios = <&pioD 13 0>, <0>, <0>, <&pioD 16 0>;
+	status = "okay";
+};
+
+&spi1 {
+	pinctrl-names = "default", "cs";
+	pinctrl-1 = <&pinctrl_spi1_cs>;
+	cs-gpios = <&pioC 25 0>, <0>, <0>, <&pioC 28 0>;
+	status = "okay";
+};
+
+&tcb0 {
+	timer0: timer@0 {
+		compatible = "atmel,tcb-timer";
+		reg = <0>;
+	};
+
+	timer1: timer@1 {
+		compatible = "atmel,tcb-timer";
+		reg = <1>;
+	};
+};
+
+&usb0 {	/* USB Device port with VBUS detection. */
+	atmel,vbus-gpio = <&pioE 9 GPIO_ACTIVE_HIGH>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usba_vbus>;
+	status = "okay";
+};
+
+&usb1 {	/* 3-port Host. First port is unused. */
+	atmel,vbus-gpio = <0
+			   &pioE 3 GPIO_ACTIVE_HIGH
+			   &pioE 4 GPIO_ACTIVE_HIGH
+			  >;
+	num-ports = <3>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb_default>;
+	status = "okay";
+};
+
+&usb2 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/at91-sama5d3_ksz9477_evb.dts b/arch/arm/boot/dts/at91-sama5d3_ksz9477_evb.dts
new file mode 100644
index 000000000000..14af1fd6d247
--- /dev/null
+++ b/arch/arm/boot/dts/at91-sama5d3_ksz9477_evb.dts
@@ -0,0 +1,214 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2021 Oleksij Rempel <kernel@pengutronix.de>, Pengutronix
+ */
+/dts-v1/;
+#include "sama5d36.dtsi"
+
+/ {
+	model = "EVB-KSZ9477";
+	compatible = "microchip,sama5d3-ksz9477-evb", "atmel,sama5d36",
+		     "atmel,sama5d3", "atmel,sama5";
+
+	chosen {
+		stdout-path = &dbgu;
+	};
+
+	reg_3v3: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	reg_vcc_mmc0: regulator-mmc0 {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_mcc0_vcc>;
+		regulator-name = "mmc0-vcc";
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		gpio = <&pioE 2 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&dbgu {
+	status = "okay";
+};
+
+&ebi {
+	pinctrl-0 = <&pinctrl_ebi_nand_addr>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&i2c0 {
+	pinctrl-0 = <&pinctrl_i2c0_pu>;
+	status = "okay";
+};
+
+&macb0 {
+	phy-mode = "rgmii";
+	status = "okay";
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+};
+
+&main_xtal {
+	clock-frequency = <12000000>;
+};
+
+&mmc0 {
+	pinctrl-0 = <&pinctrl_mmc0_clk_cmd_dat0 &pinctrl_mmc0_dat1_3
+		     &pinctrl_mmc0_dat4_7 &pinctrl_mmc0_cd>;
+	status = "okay";
+
+	slot@0 {
+		reg = <0>;
+		bus-width = <8>;
+		cd-gpios = <&pioE 0 GPIO_ACTIVE_LOW>;
+		disable-wp;
+		vmmc-supply = <&reg_vcc_mmc0>;
+		vqmmc-supply = <&reg_3v3>;
+	};
+};
+
+&nand_controller {
+	status = "okay";
+
+	nand@3 {
+		reg = <0x3 0x0 0x2>;
+		atmel,rb = <0>;
+		nand-bus-width = <8>;
+		nand-ecc-mode = "hw";
+		nand-ecc-strength = <4>;
+		nand-ecc-step-size = <512>;
+		nand-on-flash-bbt;
+		label = "atmel_nand";
+	};
+};
+
+&slow_xtal {
+	clock-frequency = <32768>;
+};
+
+&spi0 {
+	cs-gpios = <&pioD 13 GPIO_ACTIVE_LOW>, <0>, <0>,
+		   <&pioD 16 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&spi1 {
+	pinctrl-0 = <&pinctrl_spi_ksz>;
+	cs-gpios = <&pioC 25 GPIO_ACTIVE_LOW>;
+	status = "okay";
+
+	switch@0 {
+		compatible = "microchip,ksz9477";
+		reg = <0>;
+		spi-max-frequency = <1000000>;
+		spi-cpha;
+		spi-cpol;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				label = "lan1";
+				phy-mode = "internal";
+			};
+
+			port@1 {
+				reg = <1>;
+				label = "lan2";
+				phy-mode = "internal";
+			};
+
+			port@2 {
+				reg = <2>;
+				label = "lan3";
+				phy-mode = "internal";
+			};
+
+			port@3 {
+				reg = <3>;
+				label = "lan4";
+				phy-mode = "internal";
+			};
+
+			port@4 {
+				reg = <4>;
+				label = "lan5";
+				phy-mode = "internal";
+			};
+
+			port@5 {
+				reg = <5>;
+				label = "cpu";
+				ethernet = <&macb0>;
+				phy-mode = "rgmii-txid";
+
+				fixed-link {
+					speed = <1000>;
+					full-duplex;
+				};
+			};
+		};
+	};
+};
+
+&usb0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usba_vbus>;
+	atmel,vbus-gpio = <&pioE 9 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+};
+
+&pinctrl {
+	board {
+		pinctrl_i2c0_pu: i2c0-pu {
+			atmel,pins =
+				<AT91_PIOA 30 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>,
+				<AT91_PIOA 31 AT91_PERIPH_A AT91_PINCTRL_PULL_UP>;
+		};
+
+		pinctrl_mmc0_cd: mmc0-cd {
+			atmel,pins = <AT91_PIOE 0 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+		};
+
+		pinctrl_mcc0_vcc: mmc0-vcc {
+			atmel,pins = <AT91_PIOE 2 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+		};
+
+		pinctrl_spi_ksz: spi-ksz {
+			atmel,pins =
+				<
+				/* SPI1_MISO */
+				AT91_PIOC 22 AT91_PERIPH_A AT91_PINCTRL_PULL_UP
+				/* SPI1_MOSI */
+				AT91_PIOC 23 AT91_PERIPH_A AT91_PINCTRL_NONE
+				/* SPI1_SPCK */
+				AT91_PIOC 24 AT91_PERIPH_A AT91_PINCTRL_NONE
+
+				/* SPI CS */
+				AT91_PIOC 25 AT91_PERIPH_GPIO AT91_PINCTRL_NONE
+				/* switch IRQ */
+				AT91_PIOB 28 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH
+				/* switch PME_N, SoC IN */
+				AT91_PIOC 30 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP
+				/* switch RST */
+				AT91_PIOC 31 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH
+				>;
+		};
+
+		pinctrl_usba_vbus: usba-vbus {
+			atmel,pins =
+				<AT91_PIOE 9 AT91_PERIPH_GPIO AT91_PINCTRL_DEGLITCH>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/at91-sama5d3_xplained.dts b/arch/arm/boot/dts/at91-sama5d3_xplained.dts
index d72c042f2850..1f42a6a981bf 100644
--- a/arch/arm/boot/dts/at91-sama5d3_xplained.dts
+++ b/arch/arm/boot/dts/at91-sama5d3_xplained.dts
@@ -57,8 +57,8 @@
 			};
 
 			spi0: spi@f0004000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&pinctrl_spi0_cs>;
+				pinctrl-names = "default", "cs";
+				pinctrl-1 = <&pinctrl_spi0_cs>;
 				cs-gpios = <&pioD 13 0>, <0>, <0>, <&pioD 16 0>;
 				status = "okay";
 			};
@@ -171,8 +171,8 @@
 			};
 
 			spi1: spi@f8008000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&pinctrl_spi1_cs>;
+				pinctrl-names = "default", "cs";
+				pinctrl-1 = <&pinctrl_spi1_cs>;
 				cs-gpios = <&pioC 25 0>;
 				status = "okay";
 			};
@@ -372,13 +372,13 @@
 		regulator-always-on;
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_key_gpio>;
 
-		bp3 {
+		button {
 			label = "PB_USER";
 			gpios = <&pioE 29 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_PROG1>;
diff --git a/arch/arm/boot/dts/at91-sama5d4_ma5d4.dtsi b/arch/arm/boot/dts/at91-sama5d4_ma5d4.dtsi
index 710cb72bda5a..fd1086f52b40 100644
--- a/arch/arm/boot/dts/at91-sama5d4_ma5d4.dtsi
+++ b/arch/arm/boot/dts/at91-sama5d4_ma5d4.dtsi
@@ -49,7 +49,7 @@
 				cs-gpios = <&pioC 3 0>, <0>, <0>, <0>;
 				status = "okay";
 
-				m25p80@0 {
+				flash@0 {
 					compatible = "atmel,at25df321a";
 					spi-max-frequency = <50000000>;
 					reg = <0>;
diff --git a/arch/arm/boot/dts/at91-sama5d4_xplained.dts b/arch/arm/boot/dts/at91-sama5d4_xplained.dts
index d241c24f0d83..f122f302f8e0 100644
--- a/arch/arm/boot/dts/at91-sama5d4_xplained.dts
+++ b/arch/arm/boot/dts/at91-sama5d4_xplained.dts
@@ -81,8 +81,8 @@
 			};
 
 			spi1: spi@fc018000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&pinctrl_spi0_cs>;
+				pinctrl-names = "default", "cs";
+				pinctrl-1 = <&pinctrl_spi1_cs>;
 				cs-gpios = <&pioB 21 0>;
 				status = "okay";
 			};
@@ -140,7 +140,7 @@
 						atmel,pins =
 							<AT91_PIOE 1 AT91_PERIPH_GPIO AT91_PINCTRL_PULL_UP_DEGLITCH>;
 					};
-					pinctrl_spi0_cs: spi0_cs_default {
+					pinctrl_spi1_cs: spi1_cs_default {
 						atmel,pins =
 							<AT91_PIOB 21 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
 					};
@@ -242,13 +242,13 @@
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_key_gpio>;
 
-		pb_user1 {
+		button {
 			label = "pb_user1";
 			gpios = <&pioE 8 GPIO_ACTIVE_HIGH>;
 			linux,code = <KEY_PROG1>;
diff --git a/arch/arm/boot/dts/at91-sama5d4ek.dts b/arch/arm/boot/dts/at91-sama5d4ek.dts
index fe432b6b7e95..fce4e93c6bee 100644
--- a/arch/arm/boot/dts/at91-sama5d4ek.dts
+++ b/arch/arm/boot/dts/at91-sama5d4ek.dts
@@ -65,7 +65,7 @@
 			spi0: spi@f8010000 {
 				cs-gpios = <&pioC 3 0>, <0>, <0>, <0>;
 				status = "okay";
-				m25p80@0 {
+				flash@0 {
 					compatible = "atmel,at25df321a";
 					spi-max-frequency = <50000000>;
 					reg = <0>;
@@ -269,13 +269,13 @@
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_key_gpio>;
 
-		pb_user1 {
+		button {
 			label = "pb_user1";
 			gpios = <&pioE 13 GPIO_ACTIVE_HIGH>;
 			linux,code = <0x100>;
diff --git a/arch/arm/boot/dts/at91-sama7g5ek.dts b/arch/arm/boot/dts/at91-sama7g5ek.dts
index 0e1975c6812e..3b25c67795dd 100644
--- a/arch/arm/boot/dts/at91-sama7g5ek.dts
+++ b/arch/arm/boot/dts/at91-sama7g5ek.dts
@@ -13,6 +13,8 @@
 #include "sama7g5.dtsi"
 #include <dt-bindings/mfd/atmel-flexcom.h>
 #include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/at91.h>
+#include <dt-bindings/sound/microchip,pdmc.h>
 
 / {
 	model = "Microchip SAMA7G5-EK";
@@ -43,13 +45,13 @@
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_key_gpio_default>;
 
-		bp1 {
+		button {
 			label = "PB_USER";
 			gpios = <&pioA PIN_PA12 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_PROG1>;
@@ -130,10 +132,75 @@
 	status = "okay";
 };
 
+&can0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can0_default>;
+	status = "okay";
+};
+
+&can1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can1_default>;
+	status = "okay";
+};
+
 &cpu0 {
 	cpu-supply = <&vddcpu>;
 };
 
+&qspi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_qspi>;
+	status = "okay";
+
+	flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <133000000>;
+		spi-tx-bus-width = <8>;
+		spi-rx-bus-width = <8>;
+		m25p,fast-read;
+
+		at91bootstrap@0 {
+			label = "ospi: at91bootstrap";
+			reg = <0x0 0x40000>;
+		};
+
+		bootloader@40000 {
+			label = "ospi: bootloader";
+			reg = <0x40000 0xc0000>;
+		};
+
+		bootloaderenvred@100000 {
+			label = "ospi: bootloader env redundant";
+			reg = <0x100000 0x40000>;
+		};
+
+		bootloaderenv@140000 {
+			label = "ospi: bootloader env";
+			reg = <0x140000 0x40000>;
+		};
+
+		dtb@180000 {
+			label = "ospi: device tree";
+			reg = <0x180000 0x80000>;
+		};
+
+		kernel@200000 {
+			label = "ospi: kernel";
+			reg = <0x200000 0x600000>;
+		};
+
+		rootfs@800000 {
+			label = "ospi: rootfs";
+			reg = <0x800000 0x7800000>;
+		};
+
+	};
+};
+
 &dma0 {
 	status = "okay";
 };
@@ -177,14 +244,15 @@
 			regulators {
 				vdd_3v3: VDD_IO {
 					regulator-name = "VDD_IO";
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <3700000>;
+					regulator-min-microvolt = <3300000>;
+					regulator-max-microvolt = <3300000>;
 					regulator-initial-mode = <2>;
 					regulator-allowed-modes = <2>, <4>;
 					regulator-always-on;
 
 					regulator-state-standby {
 						regulator-on-in-suspend;
+						regulator-suspend-microvolt = <3300000>;
 						regulator-mode = <4>;
 					};
 
@@ -196,8 +264,8 @@
 
 				vddioddr: VDD_DDR {
 					regulator-name = "VDD_DDR";
-					regulator-min-microvolt = <1300000>;
-					regulator-max-microvolt = <1450000>;
+					regulator-min-microvolt = <1350000>;
+					regulator-max-microvolt = <1350000>;
 					regulator-initial-mode = <2>;
 					regulator-allowed-modes = <2>, <4>;
 					regulator-always-on;
@@ -217,14 +285,15 @@
 
 				vddcore: VDD_CORE {
 					regulator-name = "VDD_CORE";
-					regulator-min-microvolt = <1100000>;
-					regulator-max-microvolt = <1850000>;
+					regulator-min-microvolt = <1150000>;
+					regulator-max-microvolt = <1150000>;
 					regulator-initial-mode = <2>;
 					regulator-allowed-modes = <2>, <4>;
 					regulator-always-on;
 
 					regulator-state-standby {
 						regulator-on-in-suspend;
+						regulator-suspend-voltage = <1150000>;
 						regulator-mode = <4>;
 					};
 
@@ -236,8 +305,8 @@
 
 				vddcpu: VDD_OTHER {
 					regulator-name = "VDD_OTHER";
-					regulator-min-microvolt = <1125000>;
-					regulator-max-microvolt = <1850000>;
+					regulator-min-microvolt = <1050000>;
+					regulator-max-microvolt = <1250000>;
 					regulator-initial-mode = <2>;
 					regulator-allowed-modes = <2>, <4>;
 					regulator-ramp-delay = <3125>;
@@ -245,6 +314,7 @@
 
 					regulator-state-standby {
 						regulator-on-in-suspend;
+						regulator-suspend-voltage = <1050000>;
 						regulator-mode = <4>;
 					};
 
@@ -256,11 +326,12 @@
 
 				vldo1: LDO1 {
 					regulator-name = "LDO1";
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <3700000>;
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
 					regulator-always-on;
 
 					regulator-state-standby {
+						regulator-suspend-voltage = <1800000>;
 						regulator-on-in-suspend;
 					};
 
@@ -275,6 +346,7 @@
 					regulator-max-microvolt = <3700000>;
 
 					regulator-state-standby {
+						regulator-suspend-voltage = <1800000>;
 						regulator-on-in-suspend;
 					};
 
@@ -385,7 +457,7 @@
 		     &pinctrl_gmac1_mdio_default
 		     &pinctrl_gmac1_phy_irq>;
 	phy-mode = "rmii";
-	status = "okay";
+	status = "okay"; /* Conflict with pdmc0. */
 
 	ethernet-phy@0 {
 		reg = <0x0>;
@@ -399,7 +471,31 @@
 	pinctrl-0 = <&pinctrl_i2s0_default>;
 };
 
+&pdmc0 {
+	#sound-dai-cells = <0>;
+	microchip,mic-pos = <MCHP_PDMC_DS0 MCHP_PDMC_CLK_NEGATIVE>, /* MIC 1 */
+			    <MCHP_PDMC_DS1 MCHP_PDMC_CLK_NEGATIVE>, /* MIC 2 */
+			    <MCHP_PDMC_DS0 MCHP_PDMC_CLK_POSITIVE>, /* MIC 3 */
+			    <MCHP_PDMC_DS1 MCHP_PDMC_CLK_POSITIVE>; /* MIC 4 */
+	status = "disabled"; /* Conflict with gmac1. */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pdmc0_default>;
+};
+
 &pioA {
+
+	pinctrl_can0_default: can0_default {
+		pinmux = <PIN_PD12__CANTX0>,
+			 <PIN_PD13__CANRX0 >;
+		bias-disable;
+	};
+
+	pinctrl_can1_default: can1_default {
+		pinmux = <PIN_PD14__CANTX1>,
+			 <PIN_PD15__CANRX1 >;
+		bias-disable;
+	};
+
 	pinctrl_flx0_default: flx0_default {
 		pinmux = <PIN_PE3__FLEXCOM0_IO0>,
 			 <PIN_PE4__FLEXCOM0_IO1>,
@@ -411,7 +507,7 @@
 	pinctrl_flx3_default: flx3_default {
 		pinmux = <PIN_PD16__FLEXCOM3_IO0>,
 			 <PIN_PD17__FLEXCOM3_IO1>;
-		bias-disable;
+		bias-pull-up;
 	};
 
 	pinctrl_flx4_default: flx4_default {
@@ -555,6 +651,32 @@
 		bias-disable;
 	};
 
+	pinctrl_pdmc0_default: pdmc0_default {
+		pinmux = <PIN_PD23__PDMC0_DS0>,
+			 <PIN_PD24__PDMC0_DS1>,
+			 <PIN_PD22__PDMC0_CLK>;
+		bias_disable;
+	};
+
+	pinctrl_qspi: qspi {
+		pinmux = <PIN_PB12__QSPI0_IO0>,
+			 <PIN_PB11__QSPI0_IO1>,
+			 <PIN_PB10__QSPI0_IO2>,
+			 <PIN_PB9__QSPI0_IO3>,
+			 <PIN_PB16__QSPI0_IO4>,
+			 <PIN_PB17__QSPI0_IO5>,
+			 <PIN_PB18__QSPI0_IO6>,
+			 <PIN_PB19__QSPI0_IO7>,
+			 <PIN_PB13__QSPI0_CS>,
+			 <PIN_PB14__QSPI0_SCK>,
+			 <PIN_PB15__QSPI0_SCKN>,
+			 <PIN_PB20__QSPI0_DQS>,
+			 <PIN_PB21__QSPI0_INT>;
+		bias-disable;
+		slew-rate = <0>;
+		atmel,drive-strength = <ATMEL_PIO_DRVSTR_ME>;
+	};
+
 	pinctrl_sdmmc0_default: sdmmc0_default {
 		cmd_data {
 			pinmux = <PIN_PA1__SDMMC0_CMD>,
diff --git a/arch/arm/boot/dts/at91-vinco.dts b/arch/arm/boot/dts/at91-vinco.dts
index a51a3372afa1..ebeaa6ab500e 100644
--- a/arch/arm/boot/dts/at91-vinco.dts
+++ b/arch/arm/boot/dts/at91-vinco.dts
@@ -59,7 +59,7 @@
 			spi0: spi@f8010000 {
 				cs-gpios = <&pioC 3 0>, <0>, <0>, <0>;
 				status = "okay";
-				m25p80@0 {
+				flash@0 {
 					compatible = "n25q32b", "jedec,spi-nor";
 					spi-max-frequency = <50000000>;
 					reg = <0>;
diff --git a/arch/arm/boot/dts/at91-wb45n.dts b/arch/arm/boot/dts/at91-wb45n.dts
index 54d130c92185..ef73f727f7bd 100644
--- a/arch/arm/boot/dts/at91-wb45n.dts
+++ b/arch/arm/boot/dts/at91-wb45n.dts
@@ -12,13 +12,10 @@
 	model = "Laird Workgroup Bridge 45N - Atmel AT91SAM (dt)";
 	compatible = "laird,wb45n", "laird,wbxx", "atmel,at91sam9x5", "atmel,at91sam9";
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 
-		irqbtn@18 {
-			reg = <18>;
+		button {
 			label = "IRQBTN";
 			linux,code = <99>;
 			gpios = <&pioB 18 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/at91-wb50n.dts b/arch/arm/boot/dts/at91-wb50n.dts
index a5e45bb95c04..ec2becf6133b 100644
--- a/arch/arm/boot/dts/at91-wb50n.dts
+++ b/arch/arm/boot/dts/at91-wb50n.dts
@@ -13,21 +13,17 @@
 	model = "Laird Workgroup Bridge 50N - Atmel SAMA5D";
 	compatible = "laird,wb50n", "atmel,sama5d31", "atmel,sama5d3", "atmel,sama5";
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 
-		btn0@10 {
-			reg = <10>;
+		button-0 {
 			label = "BTNESC";
 			linux,code = <1>; /* ESC button */
 			gpios = <&pioA 10 GPIO_ACTIVE_LOW>;
 			wakeup-source;
 		};
 
-		irqbtn@31 {
-			reg = <31>;
+		button-1 {
 			label = "IRQBTN";
 			linux,code = <99>; /* SysReq button */
 			gpios = <&pioE 31 GPIO_ACTIVE_LOW>;
@@ -90,12 +86,6 @@
 
 &spi1 {
 	status = "okay";
-
-	spidev@0 {
-		compatible = "spidev";
-		reg = <0>;
-		spi-max-frequency = <8000000>;
-	};
 };
 
 &usb0 {
diff --git a/arch/arm/boot/dts/at91rm9200.dtsi b/arch/arm/boot/dts/at91rm9200.dtsi
index d1181ead18e5..7a113325abb9 100644
--- a/arch/arm/boot/dts/at91rm9200.dtsi
+++ b/arch/arm/boot/dts/at91rm9200.dtsi
@@ -13,6 +13,7 @@
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/clock/at91.h>
+#include <dt-bindings/mfd/at91-usart.h>
 
 / {
 	#address-cells = <1>;
@@ -596,6 +597,7 @@
 			dbgu: serial@fffff200 {
 				compatible = "atmel,at91rm9200-dbgu", "atmel,at91rm9200-usart";
 				reg = <0xfffff200 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_dbgu>;
@@ -607,6 +609,7 @@
 			usart0: serial@fffc0000 {
 				compatible = "atmel,at91rm9200-usart";
 				reg = <0xfffc0000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <6 IRQ_TYPE_LEVEL_HIGH 5>;
 				atmel,use-dma-rx;
 				atmel,use-dma-tx;
@@ -620,6 +623,7 @@
 			usart1: serial@fffc4000 {
 				compatible = "atmel,at91rm9200-usart";
 				reg = <0xfffc4000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <7 IRQ_TYPE_LEVEL_HIGH 5>;
 				atmel,use-dma-rx;
 				atmel,use-dma-tx;
@@ -633,6 +637,7 @@
 			usart2: serial@fffc8000 {
 				compatible = "atmel,at91rm9200-usart";
 				reg = <0xfffc8000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <8 IRQ_TYPE_LEVEL_HIGH 5>;
 				atmel,use-dma-rx;
 				atmel,use-dma-tx;
@@ -646,6 +651,7 @@
 			usart3: serial@fffcc000 {
 				compatible = "atmel,at91rm9200-usart";
 				reg = <0xfffcc000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <23 IRQ_TYPE_LEVEL_HIGH 5>;
 				atmel,use-dma-rx;
 				atmel,use-dma-tx;
diff --git a/arch/arm/boot/dts/at91rm9200ek.dts b/arch/arm/boot/dts/at91rm9200ek.dts
index e1ef4e44e663..4624a6f076f8 100644
--- a/arch/arm/boot/dts/at91rm9200ek.dts
+++ b/arch/arm/boot/dts/at91rm9200ek.dts
@@ -73,7 +73,7 @@
 			spi0: spi@fffe0000 {
 				status = "okay";
 				cs-gpios = <&pioA 3 0>, <0>, <0>, <0>;
-				mtd_dataflash@0 {
+				flash@0 {
 					compatible = "atmel,at45", "atmel,dataflash";
 					spi-max-frequency = <15000000>;
 					reg = <0>;
@@ -94,7 +94,7 @@
 			status = "okay";
 		};
 
-		nor_flash@10000000 {
+		flash@10000000 {
 			compatible = "cfi-flash";
 			reg = <0x10000000 0x800000>;
 			linux,mtd-name = "physmap-flash.0";
diff --git a/arch/arm/boot/dts/at91sam9260.dtsi b/arch/arm/boot/dts/at91sam9260.dtsi
index 7368347c9357..789fe356dbf6 100644
--- a/arch/arm/boot/dts/at91sam9260.dtsi
+++ b/arch/arm/boot/dts/at91sam9260.dtsi
@@ -11,6 +11,7 @@
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/clock/at91.h>
+#include <dt-bindings/mfd/at91-usart.h>
 
 / {
 	#address-cells = <1>;
@@ -123,7 +124,7 @@
 				clock-names = "slow_xtal", "main_xtal";
 			};
 
-			rstc@fffffd00 {
+			reset-controller@fffffd00 {
 				compatible = "atmel,at91sam9260-rstc";
 				reg = <0xfffffd00 0x10>;
 				clocks = <&pmc PMC_TYPE_CORE PMC_SLOW>;
@@ -532,6 +533,7 @@
 			dbgu: serial@fffff200 {
 				compatible = "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
 				reg = <0xfffff200 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_dbgu>;
@@ -543,6 +545,7 @@
 			usart0: serial@fffb0000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xfffb0000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <6 IRQ_TYPE_LEVEL_HIGH 5>;
 				atmel,use-dma-rx;
 				atmel,use-dma-tx;
@@ -556,6 +559,7 @@
 			usart1: serial@fffb4000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xfffb4000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <7 IRQ_TYPE_LEVEL_HIGH 5>;
 				atmel,use-dma-rx;
 				atmel,use-dma-tx;
@@ -569,6 +573,7 @@
 			usart2: serial@fffb8000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xfffb8000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <8 IRQ_TYPE_LEVEL_HIGH 5>;
 				atmel,use-dma-rx;
 				atmel,use-dma-tx;
@@ -582,6 +587,7 @@
 			usart3: serial@fffd0000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xfffd0000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <23 IRQ_TYPE_LEVEL_HIGH 5>;
 				atmel,use-dma-rx;
 				atmel,use-dma-tx;
@@ -595,6 +601,7 @@
 			uart0: serial@fffd4000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xfffd4000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <24 IRQ_TYPE_LEVEL_HIGH 5>;
 				atmel,use-dma-rx;
 				atmel,use-dma-tx;
@@ -608,6 +615,7 @@
 			uart1: serial@fffd8000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xfffd8000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <25 IRQ_TYPE_LEVEL_HIGH 5>;
 				atmel,use-dma-rx;
 				atmel,use-dma-tx;
diff --git a/arch/arm/boot/dts/at91sam9260ek.dts b/arch/arm/boot/dts/at91sam9260ek.dts
index ce96345d28a3..bb72f050a4fe 100644
--- a/arch/arm/boot/dts/at91sam9260ek.dts
+++ b/arch/arm/boot/dts/at91sam9260ek.dts
@@ -92,7 +92,7 @@
 
 			spi0: spi@fffc8000 {
 				cs-gpios = <0>, <&pioC 11 0>, <0>, <0>;
-				mtd_dataflash@1 {
+				flash@1 {
 					compatible = "atmel,at45", "atmel,dataflash";
 					spi-max-frequency = <50000000>;
 					reg = <1>;
@@ -144,17 +144,17 @@
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
-		btn3 {
+		button-3 {
 			label = "Button 3";
 			gpios = <&pioA 30 GPIO_ACTIVE_LOW>;
 			linux,code = <0x103>;
 			wakeup-source;
 		};
 
-		btn4 {
+		button-4 {
 			label = "Button 4";
 			gpios = <&pioA 31 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_PROG1>;
diff --git a/arch/arm/boot/dts/at91sam9261.dtsi b/arch/arm/boot/dts/at91sam9261.dtsi
index 7adc36ca8a46..ee0bd1aceb3f 100644
--- a/arch/arm/boot/dts/at91sam9261.dtsi
+++ b/arch/arm/boot/dts/at91sam9261.dtsi
@@ -9,6 +9,7 @@
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/clock/at91.h>
+#include <dt-bindings/mfd/at91-usart.h>
 
 / {
 	#address-cells = <1>;
@@ -179,6 +180,7 @@
 			usart0: serial@fffb0000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xfffb0000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <6 IRQ_TYPE_LEVEL_HIGH 5>;
 				atmel,use-dma-rx;
 				atmel,use-dma-tx;
@@ -192,6 +194,7 @@
 			usart1: serial@fffb4000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xfffb4000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <7 IRQ_TYPE_LEVEL_HIGH 5>;
 				atmel,use-dma-rx;
 				atmel,use-dma-tx;
@@ -205,6 +208,7 @@
 			usart2: serial@fffb8000{
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xfffb8000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <8 IRQ_TYPE_LEVEL_HIGH 5>;
 				atmel,use-dma-rx;
 				atmel,use-dma-tx;
@@ -301,6 +305,7 @@
 			dbgu: serial@fffff200 {
 				compatible = "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
 				reg = <0xfffff200 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_dbgu>;
@@ -603,7 +608,7 @@
 				clock-names = "slow_xtal", "main_xtal";
 			};
 
-			rstc@fffffd00 {
+			reset-controller@fffffd00 {
 				compatible = "atmel,at91sam9260-rstc";
 				reg = <0xfffffd00 0x10>;
 				clocks = <&slow_xtal>;
diff --git a/arch/arm/boot/dts/at91sam9261ek.dts b/arch/arm/boot/dts/at91sam9261ek.dts
index beed819609e8..88869ca874d1 100644
--- a/arch/arm/boot/dts/at91sam9261ek.dts
+++ b/arch/arm/boot/dts/at91sam9261ek.dts
@@ -145,7 +145,7 @@
 				cs-gpios = <&pioA 3 0>, <0>, <&pioA 28 0>, <0>;
 				status = "okay";
 
-				mtd_dataflash@0 {
+				flash@0 {
 					compatible = "atmel,at45", "atmel,dataflash";
 					reg = <0>;
 					spi-max-frequency = <15000000>;
@@ -178,6 +178,10 @@
 				status = "okay";
 			};
 
+			rtc@fffffd20 {
+				atmel,rtt-rtc-time-reg = <&gpbr 0x0>;
+			};
+
 			watchdog@fffffd40 {
 				status = "okay";
 			};
@@ -207,31 +211,31 @@
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
-		button_0 {
+		button-0 {
 			label = "button_0";
 			gpios = <&pioA 27 GPIO_ACTIVE_LOW>;
 			linux,code = <256>;
 			wakeup-source;
 		};
 
-		button_1 {
+		button-1 {
 			label = "button_1";
 			gpios = <&pioA 26 GPIO_ACTIVE_LOW>;
 			linux,code = <257>;
 			wakeup-source;
 		};
 
-		button_2 {
+		button-2 {
 			label = "button_2";
 			gpios = <&pioA 25 GPIO_ACTIVE_LOW>;
 			linux,code = <258>;
 			wakeup-source;
 		};
 
-		button_3 {
+		button-3 {
 			label = "button_3";
 			gpios = <&pioA 24 GPIO_ACTIVE_LOW>;
 			linux,code = <259>;
diff --git a/arch/arm/boot/dts/at91sam9263.dtsi b/arch/arm/boot/dts/at91sam9263.dtsi
index fe45d96239c9..3ce9ea987312 100644
--- a/arch/arm/boot/dts/at91sam9263.dtsi
+++ b/arch/arm/boot/dts/at91sam9263.dtsi
@@ -9,6 +9,7 @@
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/clock/at91.h>
+#include <dt-bindings/mfd/at91-usart.h>
 
 / {
 	#address-cells = <1>;
@@ -151,7 +152,7 @@
 				clock-names = "t0_clk", "slow_clk";
 			};
 
-			rstc@fffffd00 {
+			reset-controller@fffffd00 {
 				compatible = "atmel,at91sam9260-rstc";
 				reg = <0xfffffd00 0x10>;
 				clocks = <&slow_xtal>;
@@ -540,6 +541,7 @@
 			dbgu: serial@ffffee00 {
 				compatible = "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
 				reg = <0xffffee00 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_dbgu>;
@@ -551,6 +553,7 @@
 			usart0: serial@fff8c000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xfff8c000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <7 IRQ_TYPE_LEVEL_HIGH 5>;
 				atmel,use-dma-rx;
 				atmel,use-dma-tx;
@@ -564,6 +567,7 @@
 			usart1: serial@fff90000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xfff90000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <8 IRQ_TYPE_LEVEL_HIGH 5>;
 				atmel,use-dma-rx;
 				atmel,use-dma-tx;
@@ -577,6 +581,7 @@
 			usart2: serial@fff94000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xfff94000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <9 IRQ_TYPE_LEVEL_HIGH 5>;
 				atmel,use-dma-rx;
 				atmel,use-dma-tx;
diff --git a/arch/arm/boot/dts/at91sam9263ek.dts b/arch/arm/boot/dts/at91sam9263ek.dts
index 71f60576761a..ce8baff6a9f4 100644
--- a/arch/arm/boot/dts/at91sam9263ek.dts
+++ b/arch/arm/boot/dts/at91sam9263ek.dts
@@ -95,13 +95,17 @@
 			spi0: spi@fffa4000 {
 				status = "okay";
 				cs-gpios = <&pioA 5 0>, <0>, <0>, <0>;
-				mtd_dataflash@0 {
+				flash@0 {
 					compatible = "atmel,at45", "atmel,dataflash";
 					spi-max-frequency = <50000000>;
 					reg = <0>;
 				};
 			};
 
+			rtc@fffffd20 {
+				atmel,rtt-rtc-time-reg = <&gpbr 0x0>;
+			};
+
 			watchdog@fffffd40 {
 				status = "okay";
 			};
@@ -228,17 +232,17 @@
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
-		left_click {
+		button-left-click {
 			label = "left_click";
 			gpios = <&pioC 5 GPIO_ACTIVE_LOW>;
 			linux,code = <272>;
 			wakeup-source;
 		};
 
-		right_click {
+		button-right-click {
 			label = "right_click";
 			gpios = <&pioC 4 GPIO_ACTIVE_LOW>;
 			linux,code = <273>;
diff --git a/arch/arm/boot/dts/at91sam9g20ek_common.dtsi b/arch/arm/boot/dts/at91sam9g20ek_common.dtsi
index 87bb39060e8b..60d61291f344 100644
--- a/arch/arm/boot/dts/at91sam9g20ek_common.dtsi
+++ b/arch/arm/boot/dts/at91sam9g20ek_common.dtsi
@@ -110,7 +110,7 @@
 
 			spi0: spi@fffc8000 {
 				cs-gpios = <0>, <&pioC 11 0>, <0>, <0>;
-				mtd_dataflash@1 {
+				flash@1 {
 					compatible = "atmel,at45", "atmel,dataflash";
 					spi-max-frequency = <50000000>;
 					reg = <1>;
@@ -214,25 +214,37 @@
 		24c512@50 {
 			compatible = "atmel,24c512";
 			reg = <0x50>;
+			vcc-supply = <&reg_3v3>;
 		};
 
 		wm8731: wm8731@1b {
 			compatible = "wm8731";
 			reg = <0x1b>;
+
+			/* PCK0 at 12MHz */
+			clocks = <&pmc PMC_TYPE_SYSTEM 8>;
+			clock-names = "mclk";
+			assigned-clocks = <&pmc PMC_TYPE_SYSTEM 8>;
+			assigned-clock-rates = <12000000>;
+
+			HPVDD-supply = <&vcc_dac>;
+			AVDD-supply = <&vcc_dac>;
+			DCVDD-supply = <&reg_3v3>;
+			DBVDD-supply = <&reg_3v3>;
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
-		btn3 {
+		button-3 {
 			label = "Button 3";
 			gpios = <&pioA 30 GPIO_ACTIVE_LOW>;
 			linux,code = <0x103>;
 			wakeup-source;
 		};
 
-		btn4 {
+		button-4 {
 			label = "Button 4";
 			gpios = <&pioA 31 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_PROG1>;
@@ -254,4 +266,35 @@
 		atmel,ssc-controller = <&ssc0>;
 		atmel,audio-codec = <&wm8731>;
 	};
+
+	reg_5v: fixedregulator0 {
+		compatible = "regulator-fixed";
+		regulator-name = "5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	reg_3v3: fixedregulator1 {
+		compatible = "regulator-fixed";
+		regulator-name = "3V3";
+		vin-supply = <&reg_5v>;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	reg_1v: fixedregulator2 {
+		compatible = "regulator-fixed";
+		regulator-name = "1V";
+		vin-supply = <&reg_5v>;
+		regulator-min-microvolt = <1000000>;
+		regulator-max-microvolt = <1000000>;
+	};
+
+	vcc_dac: fixedregulator3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_DAC";
+		vin-supply = <&reg_3v3>;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
 };
diff --git a/arch/arm/boot/dts/at91sam9g25-gardena-smart-gateway.dts b/arch/arm/boot/dts/at91sam9g25-gardena-smart-gateway.dts
index 7da70aeeb528..92f2c05c873f 100644
--- a/arch/arm/boot/dts/at91sam9g25-gardena-smart-gateway.dts
+++ b/arch/arm/boot/dts/at91sam9g25-gardena-smart-gateway.dts
@@ -23,7 +23,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		user_btn1 {
+		button {
 			label = "USER_BTN1";
 			gpios = <&pioA 24 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_PROG1>;
diff --git a/arch/arm/boot/dts/at91sam9g45.dtsi b/arch/arm/boot/dts/at91sam9g45.dtsi
index 2ab730fd6472..95f5d76234db 100644
--- a/arch/arm/boot/dts/at91sam9g45.dtsi
+++ b/arch/arm/boot/dts/at91sam9g45.dtsi
@@ -13,6 +13,7 @@
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/clock/at91.h>
+#include <dt-bindings/mfd/at91-usart.h>
 
 / {
 	#address-cells = <1>;
@@ -137,7 +138,7 @@
 				clock-names = "slow_clk", "main_xtal";
 			};
 
-			rstc@fffffd00 {
+			reset-controller@fffffd00 {
 				compatible = "atmel,at91sam9g45-rstc";
 				reg = <0xfffffd00 0x10>;
 				clocks = <&clk32k>;
@@ -675,6 +676,7 @@
 
 			dbgu: serial@ffffee00 {
 				compatible = "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				reg = <0xffffee00 0x200>;
 				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
 				pinctrl-names = "default";
@@ -687,6 +689,7 @@
 			usart0: serial@fff8c000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xfff8c000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <7 IRQ_TYPE_LEVEL_HIGH 5>;
 				atmel,use-dma-rx;
 				atmel,use-dma-tx;
@@ -700,6 +703,7 @@
 			usart1: serial@fff90000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xfff90000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <8 IRQ_TYPE_LEVEL_HIGH 5>;
 				atmel,use-dma-rx;
 				atmel,use-dma-tx;
@@ -713,6 +717,7 @@
 			usart2: serial@fff94000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xfff94000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <9 IRQ_TYPE_LEVEL_HIGH 5>;
 				atmel,use-dma-rx;
 				atmel,use-dma-tx;
@@ -726,6 +731,7 @@
 			usart3: serial@fff98000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xfff98000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <10 IRQ_TYPE_LEVEL_HIGH 5>;
 				atmel,use-dma-rx;
 				atmel,use-dma-tx;
diff --git a/arch/arm/boot/dts/at91sam9m10g45ek.dts b/arch/arm/boot/dts/at91sam9m10g45ek.dts
index b6256a20fbc7..7f45e81ca165 100644
--- a/arch/arm/boot/dts/at91sam9m10g45ek.dts
+++ b/arch/arm/boot/dts/at91sam9m10g45ek.dts
@@ -167,7 +167,7 @@
 			spi0: spi@fffa4000{
 				status = "okay";
 				cs-gpios = <&pioB 3 0>, <0>, <0>, <0>;
-				mtd_dataflash@0 {
+				flash@0 {
 					compatible = "atmel,at45", "atmel,dataflash";
 					spi-max-frequency = <13000000>;
 					reg = <0>;
@@ -343,48 +343,48 @@
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
-		left_click {
+		button-left-click {
 			label = "left_click";
 			gpios = <&pioB 6 GPIO_ACTIVE_LOW>;
 			linux,code = <272>;
 			wakeup-source;
 		};
 
-		right_click {
+		button-right-click {
 			label = "right_click";
 			gpios = <&pioB 7 GPIO_ACTIVE_LOW>;
 			linux,code = <273>;
 			wakeup-source;
 		};
 
-		left {
+		button-left {
 			label = "Joystick Left";
 			gpios = <&pioB 14 GPIO_ACTIVE_LOW>;
 			linux,code = <105>;
 		};
 
-		right {
+		button-right {
 			label = "Joystick Right";
 			gpios = <&pioB 15 GPIO_ACTIVE_LOW>;
 			linux,code = <106>;
 		};
 
-		up {
+		button-up {
 			label = "Joystick Up";
 			gpios = <&pioB 16 GPIO_ACTIVE_LOW>;
 			linux,code = <103>;
 		};
 
-		down {
+		button-down {
 			label = "Joystick Down";
 			gpios = <&pioB 17 GPIO_ACTIVE_LOW>;
 			linux,code = <108>;
 		};
 
-		enter {
+		button-enter {
 			label = "Joystick Press";
 			gpios = <&pioB 18 GPIO_ACTIVE_LOW>;
 			linux,code = <28>;
diff --git a/arch/arm/boot/dts/at91sam9n12.dtsi b/arch/arm/boot/dts/at91sam9n12.dtsi
index 0785389f5507..83114d26f10d 100644
--- a/arch/arm/boot/dts/at91sam9n12.dtsi
+++ b/arch/arm/boot/dts/at91sam9n12.dtsi
@@ -11,6 +11,7 @@
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/clock/at91.h>
+#include <dt-bindings/mfd/at91-usart.h>
 
 / {
 	#address-cells = <1>;
@@ -126,7 +127,7 @@
 				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
 			};
 
-			rstc@fffffe00 {
+			reset-controller@fffffe00 {
 				compatible = "atmel,at91sam9g45-rstc";
 				reg = <0xfffffe00 0x10>;
 				clocks = <&clk32k>;
@@ -593,6 +594,7 @@
 			dbgu: serial@fffff200 {
 				compatible = "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
 				reg = <0xfffff200 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_dbgu>;
@@ -618,6 +620,7 @@
 			usart0: serial@f801c000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xf801c000 0x4000>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <5 IRQ_TYPE_LEVEL_HIGH 5>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_usart0>;
@@ -629,6 +632,7 @@
 			usart1: serial@f8020000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xf8020000 0x4000>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <6 IRQ_TYPE_LEVEL_HIGH 5>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_usart1>;
@@ -640,6 +644,7 @@
 			usart2: serial@f8024000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xf8024000 0x4000>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <7 IRQ_TYPE_LEVEL_HIGH 5>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_usart2>;
@@ -651,6 +656,7 @@
 			usart3: serial@f8028000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xf8028000 0x4000>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <8 IRQ_TYPE_LEVEL_HIGH 5>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_usart3>;
diff --git a/arch/arm/boot/dts/at91sam9n12ek.dts b/arch/arm/boot/dts/at91sam9n12ek.dts
index 2bc4e6e0a923..4c644d4c6be7 100644
--- a/arch/arm/boot/dts/at91sam9n12ek.dts
+++ b/arch/arm/boot/dts/at91sam9n12ek.dts
@@ -119,7 +119,7 @@
 			spi0: spi@f0000000 {
 				status = "okay";
 				cs-gpios = <&pioA 14 0>, <0>, <0>, <0>;
-				m25p80@0 {
+				flash@0 {
 					compatible = "atmel,at25df321a";
 					spi-max-frequency = <50000000>;
 					reg = <0>;
@@ -226,10 +226,10 @@
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
-		enter {
+		button-enter {
 			label = "Enter";
 			gpios = <&pioB 3 GPIO_ACTIVE_LOW>;
 			linux,code = <28>;
diff --git a/arch/arm/boot/dts/at91sam9rl.dtsi b/arch/arm/boot/dts/at91sam9rl.dtsi
index 730d1182c73e..364a2ff0a763 100644
--- a/arch/arm/boot/dts/at91sam9rl.dtsi
+++ b/arch/arm/boot/dts/at91sam9rl.dtsi
@@ -11,6 +11,7 @@
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/pwm/pwm.h>
+#include <dt-bindings/mfd/at91-usart.h>
 
 / {
 	#address-cells = <1>;
@@ -175,6 +176,7 @@
 			usart0: serial@fffb0000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xfffb0000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <6 IRQ_TYPE_LEVEL_HIGH 5>;
 				atmel,use-dma-rx;
 				atmel,use-dma-tx;
@@ -188,6 +190,7 @@
 			usart1: serial@fffb4000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xfffb4000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <7 IRQ_TYPE_LEVEL_HIGH 5>;
 				atmel,use-dma-rx;
 				atmel,use-dma-tx;
@@ -201,6 +204,7 @@
 			usart2: serial@fffb8000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xfffb8000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <8 IRQ_TYPE_LEVEL_HIGH 5>;
 				atmel,use-dma-rx;
 				atmel,use-dma-tx;
@@ -214,6 +218,7 @@
 			usart3: serial@fffbc000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xfffbc000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <9 IRQ_TYPE_LEVEL_HIGH 5>;
 				atmel,use-dma-rx;
 				atmel,use-dma-tx;
@@ -322,6 +327,7 @@
 			dbgu: serial@fffff200 {
 				compatible = "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
 				reg = <0xfffff200 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_dbgu>;
@@ -766,7 +772,7 @@
 				clock-names = "slow_clk", "main_xtal";
 			};
 
-			rstc@fffffd00 {
+			reset-controller@fffffd00 {
 				compatible = "atmel,at91sam9260-rstc";
 				reg = <0xfffffd00 0x10>;
 				clocks = <&clk32k>;
diff --git a/arch/arm/boot/dts/at91sam9rlek.dts b/arch/arm/boot/dts/at91sam9rlek.dts
index 62981b39c815..a57351270551 100644
--- a/arch/arm/boot/dts/at91sam9rlek.dts
+++ b/arch/arm/boot/dts/at91sam9rlek.dts
@@ -180,7 +180,7 @@
 			spi0: spi@fffcc000 {
 				status = "okay";
 				cs-gpios = <&pioA 28 0>, <0>, <0>, <0>;
-				mtd_dataflash@0 {
+				flash@0 {
 					compatible = "atmel,at45", "atmel,dataflash";
 					spi-max-frequency = <15000000>;
 					reg = <0>;
@@ -212,6 +212,10 @@
 				status = "okay";
 			};
 
+			rtc@fffffd20 {
+				atmel,rtt-rtc-time-reg = <&gpbr 0x0>;
+			};
+
 			rtc@fffffe00 {
 				status = "okay";
 			};
@@ -244,17 +248,17 @@
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
-		right_click {
+		button-right-click {
 			label = "right_click";
 			gpios = <&pioB 0 GPIO_ACTIVE_LOW>;
 			linux,code = <273>;
 			wakeup-source;
 		};
 
-		left_click {
+		button-left-click {
 			label = "left_click";
 			gpios = <&pioB 1 GPIO_ACTIVE_LOW>;
 			linux,code = <272>;
diff --git a/arch/arm/boot/dts/at91sam9x5.dtsi b/arch/arm/boot/dts/at91sam9x5.dtsi
index 395e883644cd..0c26c925761b 100644
--- a/arch/arm/boot/dts/at91sam9x5.dtsi
+++ b/arch/arm/boot/dts/at91sam9x5.dtsi
@@ -13,6 +13,7 @@
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/clock/at91.h>
+#include <dt-bindings/mfd/at91-usart.h>
 
 / {
 	#address-cells = <1>;
@@ -134,7 +135,7 @@
 				clock-names = "slow_clk", "main_xtal";
 			};
 
-			reset_controller: rstc@fffffe00 {
+			reset_controller: reset-controller@fffffe00 {
 				compatible = "atmel,at91sam9g45-rstc";
 				reg = <0xfffffe00 0x10>;
 				clocks = <&clk32k>;
@@ -674,6 +675,7 @@
 			dbgu: serial@fffff200 {
 				compatible = "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
 				reg = <0xfffff200 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_dbgu>;
@@ -688,6 +690,7 @@
 			usart0: serial@f801c000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xf801c000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <5 IRQ_TYPE_LEVEL_HIGH 5>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_usart0>;
@@ -702,6 +705,7 @@
 			usart1: serial@f8020000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xf8020000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <6 IRQ_TYPE_LEVEL_HIGH 5>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_usart1>;
@@ -716,6 +720,7 @@
 			usart2: serial@f8024000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xf8024000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <7 IRQ_TYPE_LEVEL_HIGH 5>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_usart2>;
@@ -775,6 +780,7 @@
 			uart0: serial@f8040000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xf8040000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <15 IRQ_TYPE_LEVEL_HIGH 5>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_uart0>;
@@ -786,6 +792,7 @@
 			uart1: serial@f8044000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xf8044000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <16 IRQ_TYPE_LEVEL_HIGH 5>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_uart1>;
diff --git a/arch/arm/boot/dts/at91sam9x5_usart3.dtsi b/arch/arm/boot/dts/at91sam9x5_usart3.dtsi
index 098d3fef5c37..a47c765e1b20 100644
--- a/arch/arm/boot/dts/at91sam9x5_usart3.dtsi
+++ b/arch/arm/boot/dts/at91sam9x5_usart3.dtsi
@@ -8,6 +8,7 @@
 
 #include <dt-bindings/pinctrl/at91.h>
 #include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/mfd/at91-usart.h>
 
 / {
 	aliases {
@@ -44,6 +45,7 @@
 			usart3: serial@f8028000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xf8028000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <8 IRQ_TYPE_LEVEL_HIGH 5>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_usart3>;
diff --git a/arch/arm/boot/dts/at91sam9x5ek.dtsi b/arch/arm/boot/dts/at91sam9x5ek.dtsi
index 6d1264de6060..5f4eaa618ab4 100644
--- a/arch/arm/boot/dts/at91sam9x5ek.dtsi
+++ b/arch/arm/boot/dts/at91sam9x5ek.dtsi
@@ -125,7 +125,7 @@
 	cs-gpios = <&pioA 14 0>, <0>, <0>, <0>;
 	status = "disabled"; /* conflicts with mmc1 */
 
-	m25p80@0 {
+	flash@0 {
 		compatible = "atmel,at25df321a";
 		spi-max-frequency = <50000000>;
 		reg = <0>;
diff --git a/arch/arm/boot/dts/axm5516-cpus.dtsi b/arch/arm/boot/dts/axm5516-cpus.dtsi
index 3bcf4e0a3c85..f13ef80b6637 100644
--- a/arch/arm/boot/dts/axm5516-cpus.dtsi
+++ b/arch/arm/boot/dts/axm5516-cpus.dtsi
@@ -73,7 +73,7 @@
 			device_type = "cpu";
 			compatible = "arm,cortex-a15";
 			reg = <0x00>;
-			clock-frequency= <1400000000>;
+			clock-frequency = <1400000000>;
 			cpu-release-addr = <0>; // Fixed by the boot loader
 		};
 
@@ -81,7 +81,7 @@
 			device_type = "cpu";
 			compatible = "arm,cortex-a15";
 			reg = <0x01>;
-			clock-frequency= <1400000000>;
+			clock-frequency = <1400000000>;
 			cpu-release-addr = <0>; // Fixed by the boot loader
 		};
 
@@ -89,7 +89,7 @@
 			device_type = "cpu";
 			compatible = "arm,cortex-a15";
 			reg = <0x02>;
-			clock-frequency= <1400000000>;
+			clock-frequency = <1400000000>;
 			cpu-release-addr = <0>; // Fixed by the boot loader
 		};
 
@@ -97,7 +97,7 @@
 			device_type = "cpu";
 			compatible = "arm,cortex-a15";
 			reg = <0x03>;
-			clock-frequency= <1400000000>;
+			clock-frequency = <1400000000>;
 			cpu-release-addr = <0>; // Fixed by the boot loader
 		};
 
@@ -105,7 +105,7 @@
 			device_type = "cpu";
 			compatible = "arm,cortex-a15";
 			reg = <0x100>;
-			clock-frequency= <1400000000>;
+			clock-frequency = <1400000000>;
 			cpu-release-addr = <0>; // Fixed by the boot loader
 		};
 
@@ -113,7 +113,7 @@
 			device_type = "cpu";
 			compatible = "arm,cortex-a15";
 			reg = <0x101>;
-			clock-frequency= <1400000000>;
+			clock-frequency = <1400000000>;
 			cpu-release-addr = <0>; // Fixed by the boot loader
 		};
 
@@ -121,7 +121,7 @@
 			device_type = "cpu";
 			compatible = "arm,cortex-a15";
 			reg = <0x102>;
-			clock-frequency= <1400000000>;
+			clock-frequency = <1400000000>;
 			cpu-release-addr = <0>; // Fixed by the boot loader
 		};
 
@@ -129,7 +129,7 @@
 			device_type = "cpu";
 			compatible = "arm,cortex-a15";
 			reg = <0x103>;
-			clock-frequency= <1400000000>;
+			clock-frequency = <1400000000>;
 			cpu-release-addr = <0>; // Fixed by the boot loader
 		};
 
@@ -137,7 +137,7 @@
 			device_type = "cpu";
 			compatible = "arm,cortex-a15";
 			reg = <0x200>;
-			clock-frequency= <1400000000>;
+			clock-frequency = <1400000000>;
 			cpu-release-addr = <0>; // Fixed by the boot loader
 		};
 
@@ -145,7 +145,7 @@
 			device_type = "cpu";
 			compatible = "arm,cortex-a15";
 			reg = <0x201>;
-			clock-frequency= <1400000000>;
+			clock-frequency = <1400000000>;
 			cpu-release-addr = <0>; // Fixed by the boot loader
 		};
 
@@ -153,7 +153,7 @@
 			device_type = "cpu";
 			compatible = "arm,cortex-a15";
 			reg = <0x202>;
-			clock-frequency= <1400000000>;
+			clock-frequency = <1400000000>;
 			cpu-release-addr = <0>; // Fixed by the boot loader
 		};
 
@@ -161,7 +161,7 @@
 			device_type = "cpu";
 			compatible = "arm,cortex-a15";
 			reg = <0x203>;
-			clock-frequency= <1400000000>;
+			clock-frequency = <1400000000>;
 			cpu-release-addr = <0>; // Fixed by the boot loader
 		};
 
@@ -169,7 +169,7 @@
 			device_type = "cpu";
 			compatible = "arm,cortex-a15";
 			reg = <0x300>;
-			clock-frequency= <1400000000>;
+			clock-frequency = <1400000000>;
 			cpu-release-addr = <0>; // Fixed by the boot loader
 		};
 
@@ -177,7 +177,7 @@
 			device_type = "cpu";
 			compatible = "arm,cortex-a15";
 			reg = <0x301>;
-			clock-frequency= <1400000000>;
+			clock-frequency = <1400000000>;
 			cpu-release-addr = <0>; // Fixed by the boot loader
 		};
 
@@ -185,7 +185,7 @@
 			device_type = "cpu";
 			compatible = "arm,cortex-a15";
 			reg = <0x302>;
-			clock-frequency= <1400000000>;
+			clock-frequency = <1400000000>;
 			cpu-release-addr = <0>; // Fixed by the boot loader
 		};
 
@@ -193,7 +193,7 @@
 			device_type = "cpu";
 			compatible = "arm,cortex-a15";
 			reg = <0x303>;
-			clock-frequency= <1400000000>;
+			clock-frequency = <1400000000>;
 			cpu-release-addr = <0>; // Fixed by the boot loader
 		};
 	};
diff --git a/arch/arm/boot/dts/bcm-cygnus.dtsi b/arch/arm/boot/dts/bcm-cygnus.dtsi
index 8ecb7861ce10..f9f79ed82518 100644
--- a/arch/arm/boot/dts/bcm-cygnus.dtsi
+++ b/arch/arm/boot/dts/bcm-cygnus.dtsi
@@ -112,18 +112,18 @@
 			status = "disabled";
 		};
 
-		pcie_phy: phy@301d0a0 {
+		pcie_phy: pcie_phy@301d0a0 {
 			compatible = "brcm,cygnus-pcie-phy";
 			reg = <0x0301d0a0 0x14>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 
-			pcie0_phy: phy@0 {
+			pcie0_phy: pcie-phy@0 {
 				reg = <0>;
 				#phy-cells = <0>;
 			};
 
-			pcie1_phy: phy@1 {
+			pcie1_phy: pcie-phy@1 {
 				reg = <1>;
 				#phy-cells = <0>;
 			};
@@ -274,8 +274,8 @@
 			#address-cells = <3>;
 			#size-cells = <2>;
 			device_type = "pci";
-			ranges = <0x81000000 0 0	  0x28000000 0 0x00010000
-				  0x82000000 0 0x20000000 0x20000000 0 0x04000000>;
+			ranges = <0x81000000 0 0	  0x28000000 0 0x00010000>,
+				 <0x82000000 0 0x20000000 0x20000000 0 0x04000000>;
 
 			phys = <&pcie0_phy>;
 			phy-names = "pcie-phy";
@@ -283,7 +283,7 @@
 			status = "disabled";
 
 			msi-parent = <&msi0>;
-			msi0: msi-controller {
+			msi0: msi {
 				compatible = "brcm,iproc-msi";
 				msi-controller;
 				interrupt-parent = <&gic>;
@@ -309,8 +309,8 @@
 			#address-cells = <3>;
 			#size-cells = <2>;
 			device_type = "pci";
-			ranges = <0x81000000 0 0	  0x48000000 0 0x00010000
-				  0x82000000 0 0x40000000 0x40000000 0 0x04000000>;
+			ranges = <0x81000000 0 0	  0x48000000 0 0x00010000>,
+				 <0x82000000 0 0x40000000 0x40000000 0 0x04000000>;
 
 			phys = <&pcie1_phy>;
 			phy-names = "pcie-phy";
@@ -318,7 +318,7 @@
 			status = "disabled";
 
 			msi-parent = <&msi1>;
-			msi1: msi-controller {
+			msi1: msi {
 				compatible = "brcm,iproc-msi";
 				msi-controller;
 				interrupt-parent = <&gic>;
@@ -397,8 +397,8 @@
 			#size-cells = <0>;
 			interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-0 = <&spi_0>;
-			clocks = <&axi81_clk>;
-			clock-names = "apb_pclk";
+			clocks = <&axi81_clk>, <&axi81_clk>;
+			clock-names = "sspclk", "apb_pclk";
 			status = "disabled";
 		};
 
@@ -409,8 +409,8 @@
 			#size-cells = <0>;
 			interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-0 = <&spi_1>;
-			clocks = <&axi81_clk>;
-			clock-names = "apb_pclk";
+			clocks = <&axi81_clk>, <&axi81_clk>;
+			clock-names = "sspclk", "apb_pclk";
 			status = "disabled";
 		};
 
@@ -421,8 +421,8 @@
 			#size-cells = <0>;
 			interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-0 = <&spi_2>;
-			clocks = <&axi81_clk>;
-			clock-names = "apb_pclk";
+			clocks = <&axi81_clk>, <&axi81_clk>;
+			clock-names = "sspclk", "apb_pclk";
 			status = "disabled";
 		};
 
diff --git a/arch/arm/boot/dts/bcm-hr2.dtsi b/arch/arm/boot/dts/bcm-hr2.dtsi
index 84cda16f68a2..33e6ba63a1ee 100644
--- a/arch/arm/boot/dts/bcm-hr2.dtsi
+++ b/arch/arm/boot/dts/bcm-hr2.dtsi
@@ -318,7 +318,7 @@
 		status = "disabled";
 
 		msi-parent = <&msi0>;
-		msi0: msi-controller {
+		msi0: msi {
 			compatible = "brcm,iproc-msi";
 			msi-controller;
 			interrupt-parent = <&gic>;
@@ -354,7 +354,7 @@
 		status = "disabled";
 
 		msi-parent = <&msi1>;
-		msi1: msi-controller {
+		msi1: msi {
 			compatible = "brcm,iproc-msi";
 			msi-controller;
 			interrupt-parent = <&gic>;
diff --git a/arch/arm/boot/dts/bcm-nsp.dtsi b/arch/arm/boot/dts/bcm-nsp.dtsi
index 1c08daa18858..5b1dc58d40ba 100644
--- a/arch/arm/boot/dts/bcm-nsp.dtsi
+++ b/arch/arm/boot/dts/bcm-nsp.dtsi
@@ -534,7 +534,7 @@
 			};
 		};
 
-		sata: ahci@41000 {
+		sata: sata@41000 {
 			compatible = "brcm,bcm-nsp-ahci";
 			reg-names = "ahci", "top-ctrl";
 			reg = <0x41000 0x1000>, <0x40020 0x1c>;
@@ -587,7 +587,7 @@
 		status = "disabled";
 
 		msi-parent = <&msi0>;
-		msi0: msi-controller {
+		msi0: msi {
 			compatible = "brcm,iproc-msi";
 			msi-controller;
 			interrupt-parent = <&gic>;
@@ -624,7 +624,7 @@
 		status = "disabled";
 
 		msi-parent = <&msi1>;
-		msi1: msi-controller {
+		msi1: msi {
 			compatible = "brcm,iproc-msi";
 			msi-controller;
 			interrupt-parent = <&gic>;
@@ -661,7 +661,7 @@
 		status = "disabled";
 
 		msi-parent = <&msi2>;
-		msi2: msi-controller {
+		msi2: msi {
 			compatible = "brcm,iproc-msi";
 			msi-controller;
 			interrupt-parent = <&gic>;
diff --git a/arch/arm/boot/dts/bcm11351.dtsi b/arch/arm/boot/dts/bcm11351.dtsi
index 6197e7d80e3b..53696078bbf0 100644
--- a/arch/arm/boot/dts/bcm11351.dtsi
+++ b/arch/arm/boot/dts/bcm11351.dtsi
@@ -1,15 +1,5 @@
-/*
- * Copyright (C) 2012-2013 Broadcom Corporation
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation version 2.
- *
- * This program is distributed "as is" WITHOUT ANY WARRANTY of any
- * kind, whether express or implied; without even the implied warranty
- * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- */
+// SPDX-License-Identifier: GPL-2.0-only
+// Copyright (C) 2012-2013 Broadcom Corporation
 
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/interrupt-controller/irq.h>
diff --git a/arch/arm/boot/dts/bcm21664-garnet.dts b/arch/arm/boot/dts/bcm21664-garnet.dts
index be468f4adc37..1854cd907a1b 100644
--- a/arch/arm/boot/dts/bcm21664-garnet.dts
+++ b/arch/arm/boot/dts/bcm21664-garnet.dts
@@ -1,15 +1,5 @@
-/*
- * Copyright (C) 2014 Broadcom Corporation
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation version 2.
- *
- * This program is distributed "as is" WITHOUT ANY WARRANTY of any
- * kind, whether express or implied; without even the implied warranty
- * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- */
+// SPDX-License-Identifier: GPL-2.0-only
+// Copyright (C) 2014 Broadcom Corporation
 
 /dts-v1/;
 
diff --git a/arch/arm/boot/dts/bcm21664.dtsi b/arch/arm/boot/dts/bcm21664.dtsi
index cc58f2b926b9..2684c37cb3a0 100644
--- a/arch/arm/boot/dts/bcm21664.dtsi
+++ b/arch/arm/boot/dts/bcm21664.dtsi
@@ -1,15 +1,5 @@
-/*
- * Copyright (C) 2014 Broadcom Corporation
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation version 2.
- *
- * This program is distributed "as is" WITHOUT ANY WARRANTY of any
- * kind, whether express or implied; without even the implied warranty
- * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- */
+// SPDX-License-Identifier: GPL-2.0-only
+// Copyright (C) 2014 Broadcom Corporation
 
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/interrupt-controller/irq.h>
diff --git a/arch/arm/boot/dts/bcm2711-rpi-4-b.dts b/arch/arm/boot/dts/bcm2711-rpi-4-b.dts
index 631dd5baf68d..4432412044de 100644
--- a/arch/arm/boot/dts/bcm2711-rpi-4-b.dts
+++ b/arch/arm/boot/dts/bcm2711-rpi-4-b.dts
@@ -65,12 +65,12 @@
 };
 
 &expgpio {
-	gpio-line-names = "BT_ON",
+	gpio-line-names = "BT_ON",		/*  0 */
 			  "WL_ON",
 			  "PWR_LED_OFF",
 			  "GLOBAL_RESET",
 			  "VDD_SD_IO_SEL",
-			  "CAM_GPIO",
+			  "CAM_GPIO",		/*  5 */
 			  "SD_PWR_ON",
 			  "";
 };
@@ -84,66 +84,66 @@
 	 * "FOO" = GPIO line named "FOO" on the schematic
 	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
 	 */
-	gpio-line-names = "ID_SDA",
+	gpio-line-names = "ID_SDA",		/*  0 */
 			  "ID_SCL",
 			  "SDA1",
 			  "SCL1",
 			  "GPIO_GCLK",
-			  "GPIO5",
+			  "GPIO5",		/*  5 */
 			  "GPIO6",
 			  "SPI_CE1_N",
 			  "SPI_CE0_N",
 			  "SPI_MISO",
-			  "SPI_MOSI",
+			  "SPI_MOSI",		/* 10 */
 			  "SPI_SCLK",
 			  "GPIO12",
 			  "GPIO13",
 			  /* Serial port */
 			  "TXD1",
-			  "RXD1",
+			  "RXD1",		/* 15 */
 			  "GPIO16",
 			  "GPIO17",
 			  "GPIO18",
 			  "GPIO19",
-			  "GPIO20",
+			  "GPIO20",		/* 20 */
 			  "GPIO21",
 			  "GPIO22",
 			  "GPIO23",
 			  "GPIO24",
-			  "GPIO25",
+			  "GPIO25",		/* 25 */
 			  "GPIO26",
 			  "GPIO27",
 			  "RGMII_MDIO",
 			  "RGMIO_MDC",
 			  /* Used by BT module */
-			  "CTS0",
+			  "CTS0",		/* 30 */
 			  "RTS0",
 			  "TXD0",
 			  "RXD0",
 			  /* Used by Wifi */
 			  "SD1_CLK",
-			  "SD1_CMD",
+			  "SD1_CMD",		/* 35 */
 			  "SD1_DATA0",
 			  "SD1_DATA1",
 			  "SD1_DATA2",
 			  "SD1_DATA3",
 			  /* Shared with SPI flash */
-			  "PWM0_MISO",
+			  "PWM0_MISO",		/* 40 */
 			  "PWM1_MOSI",
 			  "STATUS_LED_G_CLK",
 			  "SPIFLASH_CE_N",
 			  "SDA0",
-			  "SCL0",
+			  "SCL0",		/* 45 */
 			  "RGMII_RXCLK",
 			  "RGMII_RXCTL",
 			  "RGMII_RXD0",
 			  "RGMII_RXD1",
-			  "RGMII_RXD2",
+			  "RGMII_RXD2",		/* 50 */
 			  "RGMII_RXD3",
 			  "RGMII_TXCLK",
 			  "RGMII_TXCTL",
 			  "RGMII_TXD0",
-			  "RGMII_TXD1",
+			  "RGMII_TXD1",		/* 55 */
 			  "RGMII_TXD2",
 			  "RGMII_TXD3";
 };
diff --git a/arch/arm/boot/dts/bcm2711-rpi-400.dts b/arch/arm/boot/dts/bcm2711-rpi-400.dts
index f4d2fc20397c..c53d9eb0b802 100644
--- a/arch/arm/boot/dts/bcm2711-rpi-400.dts
+++ b/arch/arm/boot/dts/bcm2711-rpi-400.dts
@@ -28,12 +28,12 @@
 &expgpio {
 	gpio-line-names = "BT_ON",
 			  "WL_ON",
-			  "",
+			  "PWR_LED_OFF",
 			  "GLOBAL_RESET",
 			  "VDD_SD_IO_SEL",
-			  "CAM_GPIO",
+			  "GLOBAL_SHUTDOWN",
 			  "SD_PWR_ON",
-			  "SD_OC_N";
+			  "SHUTDOWN_REQUEST";
 };
 
 &genet_mdio {
diff --git a/arch/arm/boot/dts/bcm2711-rpi.dtsi b/arch/arm/boot/dts/bcm2711-rpi.dtsi
index ca266c5d9f9b..98817a6675b9 100644
--- a/arch/arm/boot/dts/bcm2711-rpi.dtsi
+++ b/arch/arm/boot/dts/bcm2711-rpi.dtsi
@@ -69,6 +69,10 @@
 	};
 };
 
+&v3d {
+	clocks = <&firmware_clocks 5>;
+};
+
 &vchiq {
 	interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
 };
diff --git a/arch/arm/boot/dts/bcm2711.dtsi b/arch/arm/boot/dts/bcm2711.dtsi
index 9e01dbca4a01..941c4d16791b 100644
--- a/arch/arm/boot/dts/bcm2711.dtsi
+++ b/arch/arm/boot/dts/bcm2711.dtsi
@@ -107,12 +107,13 @@
 		};
 
 		pm: watchdog@7e100000 {
-			compatible = "brcm,bcm2835-pm", "brcm,bcm2835-pm-wdt";
+			compatible = "brcm,bcm2711-pm", "brcm,bcm2835-pm-wdt";
 			#power-domain-cells = <1>;
 			#reset-cells = <1>;
 			reg = <0x7e100000 0x114>,
 			      <0x7e00a000 0x24>,
 			      <0x7ec11000 0x20>;
+			reg-names = "pm", "asb", "rpivid_asb";
 			clocks = <&clocks BCM2835_CLOCK_V3D>,
 				 <&clocks BCM2835_CLOCK_PERI_IMAGE>,
 				 <&clocks BCM2835_CLOCK_H264>,
@@ -290,6 +291,7 @@
 
 		hvs: hvs@7e400000 {
 			compatible = "brcm,bcm2711-hvs";
+			reg = <0x7e400000 0x8000>;
 			interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
 		};
 
@@ -458,12 +460,26 @@
 		#size-cells = <0>;
 		enable-method = "brcm,bcm2836-smp"; // for ARM 32-bit
 
+		/* Source for d/i-cache-line-size and d/i-cache-sets
+		 * https://developer.arm.com/documentation/100095/0003
+		 * /Level-1-Memory-System/About-the-L1-memory-system?lang=en
+		 * Source for d/i-cache-size
+		 * https://www.raspberrypi.com/documentation/computers
+		 * /processors.html#bcm2711
+		 */
 		cpu0: cpu@0 {
 			device_type = "cpu";
 			compatible = "arm,cortex-a72";
 			reg = <0>;
 			enable-method = "spin-table";
 			cpu-release-addr = <0x0 0x000000d8>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <256>; // 32KiB(size)/64(line-size)=512ways/2-way set
+			i-cache-size = <0xc000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>; // 48KiB(size)/64(line-size)=768ways/3-way set
+			next-level-cache = <&l2>;
 		};
 
 		cpu1: cpu@1 {
@@ -472,6 +488,13 @@
 			reg = <1>;
 			enable-method = "spin-table";
 			cpu-release-addr = <0x0 0x000000e0>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <256>; // 32KiB(size)/64(line-size)=512ways/2-way set
+			i-cache-size = <0xc000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>; // 48KiB(size)/64(line-size)=768ways/3-way set
+			next-level-cache = <&l2>;
 		};
 
 		cpu2: cpu@2 {
@@ -480,6 +503,13 @@
 			reg = <2>;
 			enable-method = "spin-table";
 			cpu-release-addr = <0x0 0x000000e8>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <256>; // 32KiB(size)/64(line-size)=512ways/2-way set
+			i-cache-size = <0xc000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>; // 48KiB(size)/64(line-size)=768ways/3-way set
+			next-level-cache = <&l2>;
 		};
 
 		cpu3: cpu@3 {
@@ -488,6 +518,28 @@
 			reg = <3>;
 			enable-method = "spin-table";
 			cpu-release-addr = <0x0 0x000000f0>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <256>; // 32KiB(size)/64(line-size)=512ways/2-way set
+			i-cache-size = <0xc000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>; // 48KiB(size)/64(line-size)=768ways/3-way set
+			next-level-cache = <&l2>;
+		};
+
+		/* Source for d/i-cache-line-size and d/i-cache-sets
+		 *  https://developer.arm.com/documentation/100095/0003
+		 *  /Level-2-Memory-System/About-the-L2-memory-system?lang=en
+		 *  Source for d/i-cache-size
+		 *  https://www.raspberrypi.com/documentation/computers
+		 *  /processors.html#bcm2711
+		 */
+		l2: l2-cache0 {
+			compatible = "cache";
+			cache-size = <0x100000>;
+			cache-line-size = <64>;
+			cache-sets = <1024>; // 1MiB(size)/64(line-size)=16384ways/16-way set
+			cache-level = <2>;
 		};
 	};
 
@@ -550,6 +602,17 @@
 				#size-cells = <0x0>;
 			};
 		};
+
+		v3d: gpu@7ec00000 {
+			compatible = "brcm,2711-v3d";
+			reg = <0x0 0x7ec00000 0x4000>,
+			      <0x0 0x7ec04000 0x4000>;
+			reg-names = "hub", "core0";
+
+			power-domains = <&pm BCM2835_POWER_DOMAIN_GRAFX_V3D>;
+			resets = <&pm BCM2835_RESET_V3D>;
+			interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
+		};
 	};
 };
 
@@ -582,6 +645,8 @@
 		     <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>,
 		     <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>;
 
+	gpio-ranges = <&gpio 0 0 58>;
+
 	gpclk0_gpio49: gpclk0_gpio49 {
 		pin-gpclk {
 			pins = "gpio49";
diff --git a/arch/arm/boot/dts/bcm28155-ap.dts b/arch/arm/boot/dts/bcm28155-ap.dts
index ead6e9804dbf..fce3d5260b00 100644
--- a/arch/arm/boot/dts/bcm28155-ap.dts
+++ b/arch/arm/boot/dts/bcm28155-ap.dts
@@ -1,15 +1,5 @@
-/*
- * Copyright (C) 2013 Broadcom Corporation
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation version 2.
- *
- * This program is distributed "as is" WITHOUT ANY WARRANTY of any
- * kind, whether express or implied; without even the implied warranty
- * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- */
+// SPDX-License-Identifier: GPL-2.0-only
+// Copyright (C) 2013 Broadcom Corporation
 
 /dts-v1/;
 
@@ -31,22 +21,22 @@
 	};
 
 	i2c@3e016000 {
-		status="okay";
+		status = "okay";
 		clock-frequency = <400000>;
 	};
 
 	i2c@3e017000 {
-		status="okay";
+		status = "okay";
 		clock-frequency = <400000>;
 	};
 
 	i2c@3e018000 {
-		status="okay";
+		status = "okay";
 		clock-frequency = <400000>;
 	};
 
 	i2c@3500d000 {
-		status="okay";
+		status = "okay";
 		clock-frequency = <100000>;
 
 		pmu: pmu@8 {
diff --git a/arch/arm/boot/dts/bcm2835-common.dtsi b/arch/arm/boot/dts/bcm2835-common.dtsi
index c25e797b9060..a037d2bc5b11 100644
--- a/arch/arm/boot/dts/bcm2835-common.dtsi
+++ b/arch/arm/boot/dts/bcm2835-common.dtsi
@@ -62,6 +62,7 @@
 			#reset-cells = <1>;
 			reg = <0x7e100000 0x114>,
 			      <0x7e00a000 0x24>;
+			reg-names = "pm", "asb";
 			clocks = <&clocks BCM2835_CLOCK_V3D>,
 				 <&clocks BCM2835_CLOCK_PERI_IMAGE>,
 				 <&clocks BCM2835_CLOCK_H264>,
diff --git a/arch/arm/boot/dts/bcm2835-rpi-a-plus.dts b/arch/arm/boot/dts/bcm2835-rpi-a-plus.dts
index 40b9405f1a8e..9b9a18bbb20a 100644
--- a/arch/arm/boot/dts/bcm2835-rpi-a-plus.dts
+++ b/arch/arm/boot/dts/bcm2835-rpi-a-plus.dts
@@ -32,7 +32,6 @@
 	 * This is based on the unreleased schematic for the Model A+.
 	 *
 	 * Legend:
-	 * "NC" = not connected (no rail from the SoC)
 	 * "FOO" = GPIO line named "FOO" on the schematic
 	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
 	 */
@@ -67,21 +66,21 @@
 			  "GPIO27",
 			  "SDA0",
 			  "SCL0",
-			  "NC", /* GPIO30 */
-			  "NC", /* GPIO31 */
+			  "", /* GPIO30 */
+			  "", /* GPIO31 */
 			  "CAM_GPIO1", /* GPIO32 */
-			  "NC", /* GPIO33 */
-			  "NC", /* GPIO34 */
+			  "", /* GPIO33 */
+			  "", /* GPIO34 */
 			  "PWR_LOW_N", /* GPIO35 */
-			  "NC", /* GPIO36 */
-			  "NC", /* GPIO37 */
+			  "", /* GPIO36 */
+			  "", /* GPIO37 */
 			  "USB_LIMIT", /* GPIO38 */
-			  "NC", /* GPIO39 */
+			  "", /* GPIO39 */
 			  "PWM0_OUT", /* GPIO40 */
 			  "CAM_GPIO0", /* GPIO41 */
-			  "NC", /* GPIO42 */
-			  "NC", /* GPIO43 */
-			  "NC", /* GPIO44 */
+			  "", /* GPIO42 */
+			  "", /* GPIO43 */
+			  "", /* GPIO44 */
 			  "PWM1_OUT", /* GPIO45 */
 			  "HDMI_HPD_N",
 			  "STATUS_LED",
diff --git a/arch/arm/boot/dts/bcm2835-rpi-a.dts b/arch/arm/boot/dts/bcm2835-rpi-a.dts
index 11edb581dbaf..f664e4fced93 100644
--- a/arch/arm/boot/dts/bcm2835-rpi-a.dts
+++ b/arch/arm/boot/dts/bcm2835-rpi-a.dts
@@ -26,7 +26,6 @@
 	 * RPI00021 sheet 02
 	 *
 	 * Legend:
-	 * "NC" = not connected (no rail from the SoC)
 	 * "FOO" = GPIO line named "FOO" on the schematic
 	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
 	 */
@@ -42,41 +41,41 @@
 			  "SPI_MISO",
 			  "SPI_MOSI",
 			  "SPI_SCLK",
-			  "NC", /* GPIO12 */
-			  "NC", /* GPIO13 */
+			  "", /* GPIO12 */
+			  "", /* GPIO13 */
 			  /* Serial port */
 			  "TXD0",
 			  "RXD0",
 			  "STATUS_LED_N",
 			  "GPIO17",
 			  "GPIO18",
-			  "NC", /* GPIO19 */
-			  "NC", /* GPIO20 */
+			  "", /* GPIO19 */
+			  "", /* GPIO20 */
 			  "GPIO21",
 			  "GPIO22",
 			  "GPIO23",
 			  "GPIO24",
 			  "GPIO25",
-			  "NC", /* GPIO26 */
+			  "", /* GPIO26 */
 			  "CAM_GPIO0",
 			  /* Binary number representing build/revision */
 			  "CONFIG0",
 			  "CONFIG1",
 			  "CONFIG2",
 			  "CONFIG3",
-			  "NC", /* GPIO32 */
-			  "NC", /* GPIO33 */
-			  "NC", /* GPIO34 */
-			  "NC", /* GPIO35 */
-			  "NC", /* GPIO36 */
-			  "NC", /* GPIO37 */
-			  "NC", /* GPIO38 */
-			  "NC", /* GPIO39 */
+			  "", /* GPIO32 */
+			  "", /* GPIO33 */
+			  "", /* GPIO34 */
+			  "", /* GPIO35 */
+			  "", /* GPIO36 */
+			  "", /* GPIO37 */
+			  "", /* GPIO38 */
+			  "", /* GPIO39 */
 			  "PWM0_OUT",
-			  "NC", /* GPIO41 */
-			  "NC", /* GPIO42 */
-			  "NC", /* GPIO43 */
-			  "NC", /* GPIO44 */
+			  "", /* GPIO41 */
+			  "", /* GPIO42 */
+			  "", /* GPIO43 */
+			  "", /* GPIO44 */
 			  "PWM1_OUT",
 			  "HDMI_HPD_P",
 			  "SD_CARD_DET",
diff --git a/arch/arm/boot/dts/bcm2835-rpi-b-plus.dts b/arch/arm/boot/dts/bcm2835-rpi-b-plus.dts
index 1b435c64bd9c..248feb2ed23d 100644
--- a/arch/arm/boot/dts/bcm2835-rpi-b-plus.dts
+++ b/arch/arm/boot/dts/bcm2835-rpi-b-plus.dts
@@ -34,7 +34,6 @@
 	 * RPI-BPLUS sheet 1
 	 *
 	 * Legend:
-	 * "NC" = not connected (no rail from the SoC)
 	 * "FOO" = GPIO line named "FOO" on the schematic
 	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
 	 */
@@ -69,21 +68,21 @@
 			  "GPIO27",
 			  "SDA0",
 			  "SCL0",
-			  "NC", /* GPIO30 */
+			  "", /* GPIO30 */
 			  "LAN_RUN", /* GPIO31 */
 			  "CAM_GPIO1", /* GPIO32 */
-			  "NC", /* GPIO33 */
-			  "NC", /* GPIO34 */
+			  "", /* GPIO33 */
+			  "", /* GPIO34 */
 			  "PWR_LOW_N", /* GPIO35 */
-			  "NC", /* GPIO36 */
-			  "NC", /* GPIO37 */
+			  "", /* GPIO36 */
+			  "", /* GPIO37 */
 			  "USB_LIMIT", /* GPIO38 */
-			  "NC", /* GPIO39 */
+			  "", /* GPIO39 */
 			  "PWM0_OUT", /* GPIO40 */
 			  "CAM_GPIO0", /* GPIO41 */
-			  "NC", /* GPIO42 */
-			  "NC", /* GPIO43 */
-			  "ETHCLK", /* GPIO44 */
+			  "", /* GPIO42 */
+			  "", /* GPIO43 */
+			  "ETH_CLK", /* GPIO44 */
 			  "PWM1_OUT", /* GPIO45 */
 			  "HDMI_HPD_N",
 			  "STATUS_LED",
diff --git a/arch/arm/boot/dts/bcm2835-rpi-b-rev2.dts b/arch/arm/boot/dts/bcm2835-rpi-b-rev2.dts
index a23c25c00eea..f5b66d3f4ff3 100644
--- a/arch/arm/boot/dts/bcm2835-rpi-b-rev2.dts
+++ b/arch/arm/boot/dts/bcm2835-rpi-b-rev2.dts
@@ -27,7 +27,6 @@
 	 * RPI00022 sheet 02
 	 *
 	 * Legend:
-	 * "NC" = not connected (no rail from the SoC)
 	 * "FOO" = GPIO line named "FOO" on the schematic
 	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
 	 */
@@ -43,40 +42,40 @@
 			  "SPI_MISO",
 			  "SPI_MOSI",
 			  "SPI_SCLK",
-			  "NC", /* GPIO12 */
-			  "NC", /* GPIO13 */
+			  "", /* GPIO12 */
+			  "", /* GPIO13 */
 			  /* Serial port */
 			  "TXD0",
 			  "RXD0",
 			  "STATUS_LED_N",
 			  "GPIO17",
 			  "GPIO18",
-			  "NC", /* GPIO19 */
-			  "NC", /* GPIO20 */
+			  "", /* GPIO19 */
+			  "", /* GPIO20 */
 			  "CAM_GPIO",
 			  "GPIO22",
 			  "GPIO23",
 			  "GPIO24",
 			  "GPIO25",
-			  "NC", /* GPIO26 */
+			  "", /* GPIO26 */
 			  "GPIO27",
 			  "GPIO28",
 			  "GPIO29",
 			  "GPIO30",
 			  "GPIO31",
-			  "NC", /* GPIO32 */
-			  "NC", /* GPIO33 */
-			  "NC", /* GPIO34 */
-			  "NC", /* GPIO35 */
-			  "NC", /* GPIO36 */
-			  "NC", /* GPIO37 */
-			  "NC", /* GPIO38 */
-			  "NC", /* GPIO39 */
+			  "", /* GPIO32 */
+			  "", /* GPIO33 */
+			  "", /* GPIO34 */
+			  "", /* GPIO35 */
+			  "", /* GPIO36 */
+			  "", /* GPIO37 */
+			  "", /* GPIO38 */
+			  "", /* GPIO39 */
 			  "PWM0_OUT",
-			  "NC", /* GPIO41 */
-			  "NC", /* GPIO42 */
-			  "NC", /* GPIO43 */
-			  "NC", /* GPIO44 */
+			  "", /* GPIO41 */
+			  "", /* GPIO42 */
+			  "", /* GPIO43 */
+			  "", /* GPIO44 */
 			  "PWM1_OUT",
 			  "HDMI_HPD_P",
 			  "SD_CARD_DET",
diff --git a/arch/arm/boot/dts/bcm2835-rpi-b.dts b/arch/arm/boot/dts/bcm2835-rpi-b.dts
index 1b63d6b19750..f589bede2b11 100644
--- a/arch/arm/boot/dts/bcm2835-rpi-b.dts
+++ b/arch/arm/boot/dts/bcm2835-rpi-b.dts
@@ -27,7 +27,6 @@
 	 * RPI00021 sheet 02
 	 *
 	 * Legend:
-	 * "NC" = not connected (no rail from the SoC)
 	 * "FOO" = GPIO line named "FOO" on the schematic
 	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
 	 */
@@ -43,41 +42,40 @@
 			  "SPI_MISO",
 			  "SPI_MOSI",
 			  "SPI_SCLK",
-			  "NC", /* GPIO12 */
-			  "NC", /* GPIO13 */
+			  "", /* GPIO12 */
+			  "", /* GPIO13 */
 			  /* Serial port */
 			  "TXD0",
 			  "RXD0",
 			  "STATUS_LED_N",
 			  "GPIO17",
 			  "GPIO18",
-			  "NC", /* GPIO19 */
-			  "NC", /* GPIO20 */
-			  "GPIO21",
+			  "", /* GPIO19 */
+			  "", /* GPIO20 */
+			  "CAM_GPIO0",
 			  "GPIO22",
 			  "GPIO23",
 			  "GPIO24",
 			  "GPIO25",
-			  "NC", /* GPIO26 */
-			  "CAM_GPIO0",
-			  /* Binary number representing build/revision */
-			  "CONFIG0",
-			  "CONFIG1",
-			  "CONFIG2",
-			  "CONFIG3",
-			  "NC", /* GPIO32 */
-			  "NC", /* GPIO33 */
-			  "NC", /* GPIO34 */
-			  "NC", /* GPIO35 */
-			  "NC", /* GPIO36 */
-			  "NC", /* GPIO37 */
-			  "NC", /* GPIO38 */
-			  "NC", /* GPIO39 */
+			  "", /* GPIO26 */
+			  "GPIO27",
+			  "GPIO28",
+			  "GPIO29",
+			  "GPIO30",
+			  "GPIO31",
+			  "", /* GPIO32 */
+			  "", /* GPIO33 */
+			  "", /* GPIO34 */
+			  "", /* GPIO35 */
+			  "", /* GPIO36 */
+			  "", /* GPIO37 */
+			  "", /* GPIO38 */
+			  "", /* GPIO39 */
 			  "PWM0_OUT",
-			  "NC", /* GPIO41 */
-			  "NC", /* GPIO42 */
-			  "NC", /* GPIO43 */
-			  "NC", /* GPIO44 */
+			  "", /* GPIO41 */
+			  "", /* GPIO42 */
+			  "", /* GPIO43 */
+			  "", /* GPIO44 */
 			  "PWM1_OUT",
 			  "HDMI_HPD_P",
 			  "SD_CARD_DET",
diff --git a/arch/arm/boot/dts/bcm2835-rpi-cm1-io1.dts b/arch/arm/boot/dts/bcm2835-rpi-cm1-io1.dts
index a75c882e6575..87958a96c3e0 100644
--- a/arch/arm/boot/dts/bcm2835-rpi-cm1-io1.dts
+++ b/arch/arm/boot/dts/bcm2835-rpi-cm1-io1.dts
@@ -13,7 +13,6 @@
 	 * This is based on the official GPU firmware DT blob.
 	 *
 	 * Legend:
-	 * "NC" = not connected (no rail from the SoC)
 	 * "FOO" = GPIO line named "FOO" on the schematic
 	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
 	 */
diff --git a/arch/arm/boot/dts/bcm2835-rpi-zero-w.dts b/arch/arm/boot/dts/bcm2835-rpi-zero-w.dts
index 243236bc1e00..596bb1ef994e 100644
--- a/arch/arm/boot/dts/bcm2835-rpi-zero-w.dts
+++ b/arch/arm/boot/dts/bcm2835-rpi-zero-w.dts
@@ -39,7 +39,6 @@
 	 * This is based on the official GPU firmware DT blob.
 	 *
 	 * Legend:
-	 * "NC" = not connected (no rail from the SoC)
 	 * "FOO" = GPIO line named "FOO" on the schematic
 	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
 	 */
@@ -74,19 +73,21 @@
 			  "GPIO27",
 			  "SDA0",
 			  "SCL0",
-			  "NC", /* GPIO30 */
-			  "NC", /* GPIO31 */
-			  "NC", /* GPIO32 */
-			  "NC", /* GPIO33 */
-			  "NC", /* GPIO34 */
-			  "NC", /* GPIO35 */
-			  "NC", /* GPIO36 */
-			  "NC", /* GPIO37 */
-			  "NC", /* GPIO38 */
-			  "NC", /* GPIO39 */
+			  /* Used by BT module */
+			  "CTS0",
+			  "RTS0",
+			  "TXD0",
+			  "RXD0",
+			  /* Used by Wifi */
+			  "SD1_CLK",
+			  "SD1_CMD",
+			  "SD1_DATA0",
+			  "SD1_DATA1",
+			  "SD1_DATA2",
+			  "SD1_DATA3",
 			  "CAM_GPIO1", /* GPIO40 */
 			  "WL_ON", /* GPIO41 */
-			  "NC", /* GPIO42 */
+			  "", /* GPIO42 */
 			  "WIFI_CLK", /* GPIO43 */
 			  "CAM_GPIO0", /* GPIO44 */
 			  "BT_ON", /* GPIO45 */
diff --git a/arch/arm/boot/dts/bcm2835-rpi-zero.dts b/arch/arm/boot/dts/bcm2835-rpi-zero.dts
index 6f9b3a908f28..a65c2bca69ea 100644
--- a/arch/arm/boot/dts/bcm2835-rpi-zero.dts
+++ b/arch/arm/boot/dts/bcm2835-rpi-zero.dts
@@ -29,7 +29,6 @@
 	 * This is based on the official GPU firmware DT blob.
 	 *
 	 * Legend:
-	 * "NC" = not connected (no rail from the SoC)
 	 * "FOO" = GPIO line named "FOO" on the schematic
 	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
 	 */
@@ -64,22 +63,22 @@
 			  "GPIO27",
 			  "SDA0",
 			  "SCL0",
-			  "NC", /* GPIO30 */
-			  "NC", /* GPIO31 */
+			  "", /* GPIO30 */
+			  "", /* GPIO31 */
 			  "CAM_GPIO1", /* GPIO32 */
-			  "NC", /* GPIO33 */
-			  "NC", /* GPIO34 */
-			  "NC", /* GPIO35 */
-			  "NC", /* GPIO36 */
-			  "NC", /* GPIO37 */
-			  "NC", /* GPIO38 */
-			  "NC", /* GPIO39 */
-			  "NC", /* GPIO40 */
+			  "", /* GPIO33 */
+			  "", /* GPIO34 */
+			  "", /* GPIO35 */
+			  "", /* GPIO36 */
+			  "", /* GPIO37 */
+			  "", /* GPIO38 */
+			  "", /* GPIO39 */
+			  "", /* GPIO40 */
 			  "CAM_GPIO0", /* GPIO41 */
-			  "NC", /* GPIO42 */
-			  "NC", /* GPIO43 */
-			  "NC", /* GPIO44 */
-			  "NC", /* GPIO45 */
+			  "", /* GPIO42 */
+			  "", /* GPIO43 */
+			  "", /* GPIO44 */
+			  "", /* GPIO45 */
 			  "HDMI_HPD_N",
 			  "STATUS_LED_N",
 			  /* Used by SD Card */
diff --git a/arch/arm/boot/dts/bcm2835.dtsi b/arch/arm/boot/dts/bcm2835.dtsi
index 0549686134ea..1c90e5a44283 100644
--- a/arch/arm/boot/dts/bcm2835.dtsi
+++ b/arch/arm/boot/dts/bcm2835.dtsi
@@ -14,6 +14,23 @@
 			device_type = "cpu";
 			compatible = "arm,arm1176jzf-s";
 			reg = <0x0>;
+			/* Source for d/i-cache-line-size and d/i-cache-sets
+			 * https://developer.arm.com/documentation/ddi0301
+			 * /h/level-one-memory-system/cache-organization?lang=en
+			 *
+			 * Source for d/i-cache-size
+			 * https://forums.raspberrypi.com/viewtopic.php?t=98428
+			 *
+			 * NOTE: The BCM2835 has a L2 cache but it is dedicated to the GPU
+			 * It can be shared with the CPU through fw settings,
+			 * but this is not recommended.
+			 */
+			d-cache-size = <0x4000>;
+			d-cache-line-size = <16>;
+			d-cache-sets = <256>; // 16KiB(size)/16(line-size)=1024ways/4-way set
+			i-cache-size = <0x4000>;
+			i-cache-line-size = <16>;
+			i-cache-sets = <256>; // 16KiB(size)/16(line-size)=1024ways/4-way set
 		};
 	};
 
diff --git a/arch/arm/boot/dts/bcm2836-rpi-2-b.dts b/arch/arm/boot/dts/bcm2836-rpi-2-b.dts
index d8af8eeac7b6..3635502b1e0a 100644
--- a/arch/arm/boot/dts/bcm2836-rpi-2-b.dts
+++ b/arch/arm/boot/dts/bcm2836-rpi-2-b.dts
@@ -34,7 +34,6 @@
 	 * the official GPU firmware DT blob.
 	 *
 	 * Legend:
-	 * "NC" = not connected (no rail from the SoC)
 	 * "FOO" = GPIO line named "FOO" on the schematic
 	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
 	 */
@@ -83,7 +82,7 @@
 			  "CAM_GPIO0",
 			  "SMPS_SCL",
 			  "SMPS_SDA",
-			  "ETHCLK",
+			  "ETH_CLK",
 			  "PWM1_OUT",
 			  "HDMI_HPD_N",
 			  "STATUS_LED",
diff --git a/arch/arm/boot/dts/bcm2836.dtsi b/arch/arm/boot/dts/bcm2836.dtsi
index b390006aef79..534dacfc4dd5 100644
--- a/arch/arm/boot/dts/bcm2836.dtsi
+++ b/arch/arm/boot/dts/bcm2836.dtsi
@@ -41,11 +41,26 @@
 		#size-cells = <0>;
 		enable-method = "brcm,bcm2836-smp";
 
+		/* Source for d/i-cache-line-size and d/i-cache-sets
+		 * https://developer.arm.com/documentation/ddi0464/f/L1-Memory-System
+		 * /About-the-L1-memory-system?lang=en
+		 *
+		 * Source for d/i-cache-size
+		 * https://forums.raspberrypi.com/viewtopic.php?t=98428
+		 */
+
 		v7_cpu0: cpu@0 {
 			device_type = "cpu";
 			compatible = "arm,cortex-a7";
 			reg = <0xf00>;
 			clock-frequency = <800000000>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <128>; // 32KiB(size)/64(line-size)=512ways/4-way set
+			i-cache-size = <0x8000>;
+			i-cache-line-size = <32>;
+			i-cache-sets = <512>; // 32KiB(size)/32(line-size)=1024ways/2-way set
+			next-level-cache = <&l2>;
 		};
 
 		v7_cpu1: cpu@1 {
@@ -53,6 +68,13 @@
 			compatible = "arm,cortex-a7";
 			reg = <0xf01>;
 			clock-frequency = <800000000>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <128>; // 32KiB(size)/64(line-size)=512ways/4-way set
+			i-cache-size = <0x8000>;
+			i-cache-line-size = <32>;
+			i-cache-sets = <512>; // 32KiB(size)/32(line-size)=1024ways/2-way set
+			next-level-cache = <&l2>;
 		};
 
 		v7_cpu2: cpu@2 {
@@ -60,6 +82,13 @@
 			compatible = "arm,cortex-a7";
 			reg = <0xf02>;
 			clock-frequency = <800000000>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <128>; // 32KiB(size)/64(line-size)=512ways/4-way set
+			i-cache-size = <0x8000>;
+			i-cache-line-size = <32>;
+			i-cache-sets = <512>; // 32KiB(size)/32(line-size)=1024ways/2-way set
+			next-level-cache = <&l2>;
 		};
 
 		v7_cpu3: cpu@3 {
@@ -67,6 +96,27 @@
 			compatible = "arm,cortex-a7";
 			reg = <0xf03>;
 			clock-frequency = <800000000>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <128>; // 32KiB(size)/64(line-size)=512ways/4-way set
+			i-cache-size = <0x8000>;
+			i-cache-line-size = <32>;
+			i-cache-sets = <512>; // 32KiB(size)/32(line-size)=1024ways/2-way set
+			next-level-cache = <&l2>;
+		};
+
+		/* Source for cache-line-size + cache-sets
+		 * https://developer.arm.com/documentation/ddi0464/f/L2-Memory-System
+		 * /About-the-L2-Memory-system?lang=en
+		 * Source for cache-size
+		 * https://forums.raspberrypi.com/viewtopic.php?t=98428
+		 */
+		l2: l2-cache0 {
+			compatible = "cache";
+			cache-size = <0x80000>;
+			cache-line-size = <64>;
+			cache-sets = <1024>; // 512KiB(size)/64(line-size)=8192ways/8-way set
+			cache-level = <2>;
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/bcm2837-rpi-3-a-plus.dts b/arch/arm/boot/dts/bcm2837-rpi-3-a-plus.dts
index d73daf5bff1d..f7222a28903e 100644
--- a/arch/arm/boot/dts/bcm2837-rpi-3-a-plus.dts
+++ b/arch/arm/boot/dts/bcm2837-rpi-3-a-plus.dts
@@ -55,7 +55,6 @@
 	 * This is mostly based on the official GPU firmware DT blob.
 	 *
 	 * Legend:
-	 * "NC" = not connected (no rail from the SoC)
 	 * "FOO" = GPIO line named "FOO" on the schematic
 	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
 	 */
diff --git a/arch/arm/boot/dts/bcm2837-rpi-3-b-plus.dts b/arch/arm/boot/dts/bcm2837-rpi-3-b-plus.dts
index e12938baaf12..ec721d323ac5 100644
--- a/arch/arm/boot/dts/bcm2837-rpi-3-b-plus.dts
+++ b/arch/arm/boot/dts/bcm2837-rpi-3-b-plus.dts
@@ -45,7 +45,7 @@
 		#gpio-cells = <2>;
 		gpio-line-names = "BT_ON",
 				  "WL_ON",
-				  "STATUS_LED_R",
+				  "PWR_LED_R",
 				  "LAN_RUN",
 				  "",
 				  "CAM_GPIO0",
@@ -61,7 +61,6 @@
 	 * the official GPU firmware DT blob.
 	 *
 	 * Legend:
-	 * "NC" = not connected (no rail from the SoC)
 	 * "FOO" = GPIO line named "FOO" on the schematic
 	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
 	 */
@@ -110,7 +109,7 @@
 			  "SD1_DATA3",
 			  "PWM0_OUT",
 			  "PWM1_OUT",
-			  "ETHCLK",
+			  "ETH_CLK",
 			  "WIFI_CLK",
 			  "SDA0",
 			  "SCL0",
diff --git a/arch/arm/boot/dts/bcm2837-rpi-3-b.dts b/arch/arm/boot/dts/bcm2837-rpi-3-b.dts
index 42b5383b55d8..fb6a417d73e7 100644
--- a/arch/arm/boot/dts/bcm2837-rpi-3-b.dts
+++ b/arch/arm/boot/dts/bcm2837-rpi-3-b.dts
@@ -54,7 +54,6 @@
 	 * the official GPU firmware DT blob.
 	 *
 	 * Legend:
-	 * "NC" = not connected (no rail from the SoC)
 	 * "FOO" = GPIO line named "FOO" on the schematic
 	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
 	 */
@@ -103,7 +102,7 @@
 			  "SD1_DATA3",
 			  "PWM0_OUT",
 			  "PWM1_OUT",
-			  "ETHCLK",
+			  "ETH_CLK",
 			  "WIFI_CLK",
 			  "SDA0",
 			  "SCL0",
diff --git a/arch/arm/boot/dts/bcm2837-rpi-cm3-io3.dts b/arch/arm/boot/dts/bcm2837-rpi-cm3-io3.dts
index 588d9411ceb6..cf84e69fced8 100644
--- a/arch/arm/boot/dts/bcm2837-rpi-cm3-io3.dts
+++ b/arch/arm/boot/dts/bcm2837-rpi-cm3-io3.dts
@@ -13,7 +13,6 @@
 	 * This is based on the official GPU firmware DT blob.
 	 *
 	 * Legend:
-	 * "NC" = not connected (no rail from the SoC)
 	 * "FOO" = GPIO line named "FOO" on the schematic
 	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
 	 */
@@ -63,8 +62,8 @@
 			  "GPIO43",
 			  "GPIO44",
 			  "GPIO45",
-			  "GPIO46",
-			  "GPIO47",
+			  "SMPS_SCL",
+			  "SMPS_SDA",
 			  /* Used by eMMC */
 			  "SD_CLK_R",
 			  "SD_CMD_R",
diff --git a/arch/arm/boot/dts/bcm2837-rpi-cm3.dtsi b/arch/arm/boot/dts/bcm2837-rpi-cm3.dtsi
index 828a20561b96..f57b4ca145dd 100644
--- a/arch/arm/boot/dts/bcm2837-rpi-cm3.dtsi
+++ b/arch/arm/boot/dts/bcm2837-rpi-cm3.dtsi
@@ -41,12 +41,12 @@
 		#gpio-cells = <2>;
 		gpio-line-names = "HDMI_HPD_N",
 				  "EMMC_EN_N",
-				  "NC",
-				  "NC",
-				  "NC",
-				  "NC",
-				  "NC",
-				  "NC";
+				  "",
+				  "",
+				  "",
+				  "",
+				  "",
+				  "";
 		status = "okay";
 	};
 };
diff --git a/arch/arm/boot/dts/bcm2837-rpi-zero-2-w.dts b/arch/arm/boot/dts/bcm2837-rpi-zero-2-w.dts
new file mode 100644
index 000000000000..4a768562985e
--- /dev/null
+++ b/arch/arm/boot/dts/bcm2837-rpi-zero-2-w.dts
@@ -0,0 +1,136 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2022 Stefan Wahren <stefan.wahren@i2se.com>
+ */
+
+/dts-v1/;
+#include "bcm2837.dtsi"
+#include "bcm2836-rpi.dtsi"
+#include "bcm283x-rpi-usb-otg.dtsi"
+#include "bcm283x-rpi-wifi-bt.dtsi"
+
+/ {
+	compatible = "raspberrypi,model-zero-2-w", "brcm,bcm2837";
+	model = "Raspberry Pi Zero 2 W";
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0 0x20000000>;
+	};
+
+	chosen {
+		/* 8250 auxiliary UART instead of pl011 */
+		stdout-path = "serial1:115200n8";
+	};
+
+	leds {
+		led-act {
+			gpios = <&gpio 29 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&bt {
+	shutdown-gpios = <&gpio 42 GPIO_ACTIVE_HIGH>;
+};
+
+&gpio {
+	/*
+	 * This is based on the official GPU firmware DT blob.
+	 *
+	 * Legend:
+	 * "NC" = not connected (no rail from the SoC)
+	 * "FOO" = GPIO line named "FOO" on the schematic
+	 * "FOO_N" = GPIO line named "FOO" on schematic, active low
+	 */
+	gpio-line-names = "ID_SDA",
+			  "ID_SCL",
+			  "SDA1",
+			  "SCL1",
+			  "GPIO_GCLK",
+			  "GPIO5",
+			  "GPIO6",
+			  "SPI_CE1_N",
+			  "SPI_CE0_N",
+			  "SPI_MISO",
+			  "SPI_MOSI",
+			  "SPI_SCLK",
+			  "GPIO12",
+			  "GPIO13",
+			  /* Serial port */
+			  "TXD0",
+			  "RXD0",
+			  "GPIO16",
+			  "GPIO17",
+			  "GPIO18",
+			  "GPIO19",
+			  "GPIO20",
+			  "GPIO21",
+			  "GPIO22",
+			  "GPIO23",
+			  "GPIO24",
+			  "GPIO25",
+			  "GPIO26",
+			  "GPIO27",
+			  "HDMI_HPD_N",
+			  "STATUS_LED_N",
+			  "NC", /* GPIO30 */
+			  "NC", /* GPIO31 */
+			  "NC", /* GPIO32 */
+			  "NC", /* GPIO33 */
+			  "NC", /* GPIO34 */
+			  "NC", /* GPIO35 */
+			  "NC", /* GPIO36 */
+			  "NC", /* GPIO37 */
+			  "NC", /* GPIO38 */
+			  "NC", /* GPIO39 */
+			  "CAM_GPIO0", /* GPIO40 */
+			  "WL_ON", /* GPIO41 */
+			  "BT_ON", /* GPIO42 */
+			  "WIFI_CLK", /* GPIO43 */
+			  "SDA0", /* GPIO44 */
+			  "SCL0", /* GPIO45 */
+			  "SMPS_SCL",
+			  "SMPS_SDA",
+			  /* Used by SD Card */
+			  "SD_CLK_R",
+			  "SD_CMD_R",
+			  "SD_DATA0_R",
+			  "SD_DATA1_R",
+			  "SD_DATA2_R",
+			  "SD_DATA3_R";
+
+	pinctrl-0 = <&gpioout &alt0>;
+};
+
+&hdmi {
+	hpd-gpios = <&gpio 28 GPIO_ACTIVE_LOW>;
+	power-domains = <&power RPI_POWER_DOMAIN_HDMI>;
+	status = "okay";
+};
+
+&sdhci {
+	pinctrl-0 = <&emmc_gpio34 &gpclk2_gpio43>;
+};
+
+&sdhost {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdhost_gpio48>;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_gpio32 &uart0_ctsrts_gpio30>;
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_gpio14>;
+	status = "okay";
+};
+
+&wifi_pwrseq {
+	reset-gpios = <&gpio 41 GPIO_ACTIVE_LOW>;
+};
diff --git a/arch/arm/boot/dts/bcm2837.dtsi b/arch/arm/boot/dts/bcm2837.dtsi
index 0199ec98cd61..5dbdebc46259 100644
--- a/arch/arm/boot/dts/bcm2837.dtsi
+++ b/arch/arm/boot/dts/bcm2837.dtsi
@@ -40,12 +40,26 @@
 		#size-cells = <0>;
 		enable-method = "brcm,bcm2836-smp"; // for ARM 32-bit
 
+		/* Source for d/i-cache-line-size and d/i-cache-sets
+		 * https://developer.arm.com/documentation/ddi0500/e/level-1-memory-system
+		 * /about-the-l1-memory-system?lang=en
+		 *
+		 * Source for d/i-cache-size
+		 * https://magpi.raspberrypi.com/articles/raspberry-pi-3-specs-benchmarks
+		 */
 		cpu0: cpu@0 {
 			device_type = "cpu";
 			compatible = "arm,cortex-a53";
 			reg = <0>;
 			enable-method = "spin-table";
 			cpu-release-addr = <0x0 0x000000d8>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <128>; // 32KiB(size)/64(line-size)=512ways/4-way set
+			i-cache-size = <0x8000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>; // 32KiB(size)/64(line-size)=512ways/2-way set
+			next-level-cache = <&l2>;
 		};
 
 		cpu1: cpu@1 {
@@ -54,6 +68,13 @@
 			reg = <1>;
 			enable-method = "spin-table";
 			cpu-release-addr = <0x0 0x000000e0>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <128>; // 32KiB(size)/64(line-size)=512ways/4-way set
+			i-cache-size = <0x8000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>; // 32KiB(size)/64(line-size)=512ways/2-way set
+			next-level-cache = <&l2>;
 		};
 
 		cpu2: cpu@2 {
@@ -62,6 +83,13 @@
 			reg = <2>;
 			enable-method = "spin-table";
 			cpu-release-addr = <0x0 0x000000e8>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <128>; // 32KiB(size)/64(line-size)=512ways/4-way set
+			i-cache-size = <0x8000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>; // 32KiB(size)/64(line-size)=512ways/2-way set
+			next-level-cache = <&l2>;
 		};
 
 		cpu3: cpu@3 {
@@ -70,6 +98,27 @@
 			reg = <3>;
 			enable-method = "spin-table";
 			cpu-release-addr = <0x0 0x000000f0>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <128>; // 32KiB(size)/64(line-size)=512ways/4-way set
+			i-cache-size = <0x8000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>; // 32KiB(size)/64(line-size)=512ways/2-way set
+			next-level-cache = <&l2>;
+		};
+
+		/* Source for cache-line-size + cache-sets
+		 * https://developer.arm.com/documentation/ddi0500
+		 * /e/level-2-memory-system/about-the-l2-memory-system?lang=en
+		 * Source for cache-size
+		 * https://datasheets.raspberrypi.com/cm/cm1-and-cm3-datasheet.pdf
+		 */
+		l2: l2-cache0 {
+			compatible = "cache";
+			cache-size = <0x80000>;
+			cache-line-size = <64>;
+			cache-sets = <512>; // 512KiB(size)/64(line-size)=8192ways/16-way set
+			cache-level = <2>;
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/bcm283x-rpi-smsc9512.dtsi b/arch/arm/boot/dts/bcm283x-rpi-smsc9512.dtsi
index 967e081cb9c2..882b13807075 100644
--- a/arch/arm/boot/dts/bcm283x-rpi-smsc9512.dtsi
+++ b/arch/arm/boot/dts/bcm283x-rpi-smsc9512.dtsi
@@ -12,7 +12,7 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		ethernet: usbether@1 {
+		ethernet: ethernet@1 {
 			compatible = "usb424,ec00";
 			reg = <1>;
 		};
diff --git a/arch/arm/boot/dts/bcm283x-rpi-smsc9514.dtsi b/arch/arm/boot/dts/bcm283x-rpi-smsc9514.dtsi
index dc7ae776db5f..4273b90b53cc 100644
--- a/arch/arm/boot/dts/bcm283x-rpi-smsc9514.dtsi
+++ b/arch/arm/boot/dts/bcm283x-rpi-smsc9514.dtsi
@@ -11,7 +11,7 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		ethernet: usbether@1 {
+		ethernet: ethernet@1 {
 			compatible = "usb424,ec00";
 			reg = <1>;
 		};
diff --git a/arch/arm/boot/dts/bcm283x.dtsi b/arch/arm/boot/dts/bcm283x.dtsi
index a3e06b680947..d2d9c6e67f39 100644
--- a/arch/arm/boot/dts/bcm283x.dtsi
+++ b/arch/arm/boot/dts/bcm283x.dtsi
@@ -50,9 +50,9 @@
 
 			trips {
 				cpu-crit {
-					temperature	= <90000>;
-					hysteresis	= <0>;
-					type		= "critical";
+					temperature = <90000>;
+					hysteresis = <0>;
+					type = "critical";
 				};
 			};
 
@@ -126,6 +126,8 @@
 			interrupt-controller;
 			#interrupt-cells = <2>;
 
+			gpio-ranges = <&gpio 0 0 54>;
+
 			/* Defines common pin muxing groups
 			 *
 			 * While each pin can have its mux selected
@@ -350,8 +352,6 @@
 			clocks = <&clocks BCM2835_CLOCK_VPU>,
 				 <&clocks BCM2835_CLOCK_DPI>;
 			clock-names = "core", "pixel";
-			#address-cells = <1>;
-			#size-cells = <0>;
 			status = "disabled";
 		};
 
diff --git a/arch/arm/boot/dts/bcm4708-asus-rt-ac56u.dts b/arch/arm/boot/dts/bcm4708-asus-rt-ac56u.dts
index 8ed403767540..09ee3e46c0cc 100644
--- a/arch/arm/boot/dts/bcm4708-asus-rt-ac56u.dts
+++ b/arch/arm/boot/dts/bcm4708-asus-rt-ac56u.dts
@@ -70,19 +70,19 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		rfkill {
+		button-rfkill {
 			label = "WiFi";
 			linux,code = <KEY_RFKILL>;
 			gpios = <&chipcommon 7 GPIO_ACTIVE_LOW>;
 		};
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
 		};
 
-		wps {
+		button-wps {
 			label = "WPS";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&chipcommon 15 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/bcm4708-asus-rt-ac68u.dts b/arch/arm/boot/dts/bcm4708-asus-rt-ac68u.dts
index 667b118ba4ee..32619c6045d3 100644
--- a/arch/arm/boot/dts/bcm4708-asus-rt-ac68u.dts
+++ b/arch/arm/boot/dts/bcm4708-asus-rt-ac68u.dts
@@ -54,25 +54,25 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		brightness {
+		button-brightness {
 			label = "Backlight";
 			linux,code = <KEY_BRIGHTNESS_ZERO>;
 			gpios = <&chipcommon 5 GPIO_ACTIVE_LOW>;
 		};
 
-		wps {
+		button-wps {
 			label = "WPS";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&chipcommon 7 GPIO_ACTIVE_LOW>;
 		};
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
 		};
 
-		rfkill {
+		button-rfkill {
 			label = "WiFi";
 			linux,code = <KEY_RFKILL>;
 			gpios = <&chipcommon 15 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/bcm4708-buffalo-wzr-1166dhp-common.dtsi b/arch/arm/boot/dts/bcm4708-buffalo-wzr-1166dhp-common.dtsi
new file mode 100644
index 000000000000..a658b9b7bcec
--- /dev/null
+++ b/arch/arm/boot/dts/bcm4708-buffalo-wzr-1166dhp-common.dtsi
@@ -0,0 +1,192 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Broadcom BCM470X / BCM5301X ARM platform code.
+ * DTS for Buffalo WZR-1166DHP and WZR-1166DHP2
+ *
+ * Copyright (C) 2014 Rafał Miłecki <zajec5@gmail.com>
+ * Copyright (C) 2022 SHIMAMOTO Takayoshi <takayoshi.shimamoto.360@gmail.com>
+ */
+
+
+#include "bcm4708.dtsi"
+#include "bcm5301x-nand-cs0-bch8.dtsi"
+#include <dt-bindings/leds/common.h>
+
+/ {
+	spi {
+		compatible = "spi-gpio";
+		num-chipselects = <1>;
+		gpio-sck = <&chipcommon 7 0>;
+		gpio-mosi = <&chipcommon 4 0>;
+		cs-gpios = <&chipcommon 6 0>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		hc595: gpio_spi@0 {
+			compatible = "fairchild,74hc595";
+			reg = <0>;
+			registers-number = <1>;
+			spi-max-frequency = <100000>;
+
+			gpio-controller;
+			#gpio-cells = <2>;
+
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		usb {
+			/* label = "bcm53xx:blue:usb"; */
+			function = LED_FUNCTION_USB;
+			color = <LED_COLOR_ID_BLUE>;
+			gpios = <&hc595 0 GPIO_ACTIVE_HIGH>;
+			trigger-sources = <&ohci_port1>, <&ehci_port1>,
+					  <&xhci_port1>, <&ohci_port2>,
+					  <&ehci_port2>;
+			linux,default-trigger = "usbport";
+		};
+
+		power0 {
+			/* label = "bcm53xx:red:power"; */
+			function = LED_FUNCTION_FAULT;
+			color = <LED_COLOR_ID_RED>;
+			gpios = <&hc595 1 GPIO_ACTIVE_HIGH>;
+		};
+
+		power1 {
+			/* label = "bcm53xx:white:power"; */
+			function = LED_FUNCTION_POWER;
+			color = <LED_COLOR_ID_WHITE>;
+			gpios = <&hc595 2 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-on";
+		};
+
+		router0 {
+			/*  label = "bcm53xx:blue:router"; */
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_BLUE>;
+			gpios = <&hc595 3 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-on";
+		};
+
+		router1 {
+			/* label = "bcm53xx:amber:router"; */
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_AMBER>;
+			gpios = <&hc595 4 GPIO_ACTIVE_HIGH>;
+		};
+
+		wan {
+			/* label = "bcm53xx:blue:wan"; */
+			function = LED_FUNCTION_WAN;
+			color = <LED_COLOR_ID_BLUE>;
+			gpios = <&hc595 5 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-on";
+		};
+
+		wireless0 {
+			/* label = "bcm53xx:blue:wireless"; */
+			function = LED_FUNCTION_WLAN;
+			color = <LED_COLOR_ID_BLUE>;
+			gpios = <&hc595 6 GPIO_ACTIVE_HIGH>;
+		};
+
+		wireless1 {
+			/* label = "bcm53xx:amber:wireless"; */
+			function = LED_FUNCTION_WLAN;
+			color = <LED_COLOR_ID_AMBER>;
+			gpios = <&hc595 7 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-restart {
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
+		};
+
+		button-aoss {
+			label = "AOSS";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&chipcommon 12 GPIO_ACTIVE_LOW>;
+		};
+
+		/* Commit mode set by switch? */
+		button-mode {
+			label = "Mode";
+			linux,code = <KEY_SETUP>;
+			gpios = <&chipcommon 13 GPIO_ACTIVE_LOW>;
+		};
+
+		/* Switch: AP mode */
+		button-sw-ap {
+			label = "AP";
+			linux,code = <BTN_0>;
+			gpios = <&chipcommon 14 GPIO_ACTIVE_LOW>;
+		};
+
+		button-eject {
+			label = "USB eject";
+			linux,code = <KEY_EJECTCD>;
+			gpios = <&chipcommon 15 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&usb2 {
+	vcc-gpio = <&chipcommon 9 GPIO_ACTIVE_HIGH>;
+};
+
+&usb3 {
+	vcc-gpio = <&chipcommon 10 GPIO_ACTIVE_LOW>;
+};
+
+&spi_nor {
+	status = "okay";
+};
+
+&usb3_phy {
+	status = "okay";
+};
+
+&srab {
+	status = "okay";
+
+	ports {
+		port@0 {
+			reg = <0>;
+			label = "lan1";
+		};
+
+		port@1 {
+			reg = <1>;
+			label = "lan2";
+		};
+
+		port@2 {
+			reg = <2>;
+			label = "lan3";
+		};
+
+		port@3 {
+			reg = <3>;
+			label = "lan4";
+		};
+
+		port@4 {
+			reg = <4>;
+			label = "wan";
+		};
+
+		port@5 {
+			reg = <5>;
+			label = "cpu";
+			ethernet = <&gmac0>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/bcm4708-buffalo-wzr-1166dhp.dts b/arch/arm/boot/dts/bcm4708-buffalo-wzr-1166dhp.dts
new file mode 100644
index 000000000000..8e506269fa1a
--- /dev/null
+++ b/arch/arm/boot/dts/bcm4708-buffalo-wzr-1166dhp.dts
@@ -0,0 +1,26 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Device Tree Bindigs for Buffalo WZR-1166DHP
+ *
+ * Copyright (C) 2022 SHIMAMOTO Takayoshi <takayoshi.shimamoto.360@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "bcm4708-buffalo-wzr-1166dhp-common.dtsi"
+
+/ {
+	compatible = "buffalo,wzr-1166dhp", "brcm,bcm4708";
+	model = "Buffalo WZR-1166DHP";
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x08000000>,
+		      <0x88000000 0x18000000>;
+	};
+
+};
diff --git a/arch/arm/boot/dts/bcm4708-buffalo-wzr-1166dhp2.dts b/arch/arm/boot/dts/bcm4708-buffalo-wzr-1166dhp2.dts
new file mode 100644
index 000000000000..596129027074
--- /dev/null
+++ b/arch/arm/boot/dts/bcm4708-buffalo-wzr-1166dhp2.dts
@@ -0,0 +1,26 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Device Tree Bindigs for Buffalo WZR-1166DHP2
+ *
+ * Copyright (C) 2022 SHIMAMOTO Takayoshi <takayoshi.shimamoto.360@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "bcm4708-buffalo-wzr-1166dhp-common.dtsi"
+
+/ {
+	compatible = "buffalo,wzr-1166dhp2", "brcm,bcm4708";
+	model = "Buffalo WZR-1166DHP2";
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x08000000>,
+		      <0x88000000 0x08000000>;
+	};
+
+};
diff --git a/arch/arm/boot/dts/bcm4708-buffalo-wzr-1750dhp.dts b/arch/arm/boot/dts/bcm4708-buffalo-wzr-1750dhp.dts
index ff31ce45831a..f8f53457dd43 100644
--- a/arch/arm/boot/dts/bcm4708-buffalo-wzr-1750dhp.dts
+++ b/arch/arm/boot/dts/bcm4708-buffalo-wzr-1750dhp.dts
@@ -100,33 +100,33 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
 		};
 
-		aoss {
+		button-aoss {
 			label = "AOSS";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&chipcommon 12 GPIO_ACTIVE_LOW>;
 		};
 
 		/* Commit mode set by switch? */
-		mode {
+		button-mode {
 			label = "Mode";
 			linux,code = <KEY_SETUP>;
 			gpios = <&chipcommon 13 GPIO_ACTIVE_LOW>;
 		};
 
 		/* Switch: AP mode */
-		sw_ap {
+		button-sw-ap {
 			label = "AP";
 			linux,code = <BTN_0>;
 			gpios = <&chipcommon 14 GPIO_ACTIVE_LOW>;
 		};
 
-		eject {
+		button-eject {
 			label = "USB eject";
 			linux,code = <KEY_EJECTCD>;
 			gpios = <&chipcommon 15 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/bcm4708-linksys-ea6300-v1.dts b/arch/arm/boot/dts/bcm4708-linksys-ea6300-v1.dts
index 5bac1e15775a..0ed25bf71f0d 100644
--- a/arch/arm/boot/dts/bcm4708-linksys-ea6300-v1.dts
+++ b/arch/arm/boot/dts/bcm4708-linksys-ea6300-v1.dts
@@ -29,13 +29,13 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		wps {
+		button-wps {
 			label = "WPS";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&chipcommon 7 GPIO_ACTIVE_LOW>;
 		};
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/bcm4708-linksys-ea6500-v2.dts b/arch/arm/boot/dts/bcm4708-linksys-ea6500-v2.dts
index cd797b4202ad..f1412ba83def 100644
--- a/arch/arm/boot/dts/bcm4708-linksys-ea6500-v2.dts
+++ b/arch/arm/boot/dts/bcm4708-linksys-ea6500-v2.dts
@@ -25,13 +25,13 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		wps {
+		button-wps {
 			label = "WPS";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&chipcommon 7 GPIO_ACTIVE_LOW>;
 		};
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/bcm4708-luxul-xap-1510.dts b/arch/arm/boot/dts/bcm4708-luxul-xap-1510.dts
index 5b4a481be4f4..14ee410183af 100644
--- a/arch/arm/boot/dts/bcm4708-luxul-xap-1510.dts
+++ b/arch/arm/boot/dts/bcm4708-luxul-xap-1510.dts
@@ -45,7 +45,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/bcm4708-luxul-xwc-1000.dts b/arch/arm/boot/dts/bcm4708-luxul-xwc-1000.dts
index c81944cd6d0b..600ab087f5e5 100644
--- a/arch/arm/boot/dts/bcm4708-luxul-xwc-1000.dts
+++ b/arch/arm/boot/dts/bcm4708-luxul-xwc-1000.dts
@@ -52,7 +52,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 7 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/bcm4708-netgear-r6250.dts b/arch/arm/boot/dts/bcm4708-netgear-r6250.dts
index 43a5d675dd67..fd6d8d2a4456 100644
--- a/arch/arm/boot/dts/bcm4708-netgear-r6250.dts
+++ b/arch/arm/boot/dts/bcm4708-netgear-r6250.dts
@@ -63,19 +63,19 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		wps {
+		button-wps {
 			label = "WPS";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&chipcommon 4 GPIO_ACTIVE_LOW>;
 		};
 
-		rfkill {
+		button-rfkill {
 			label = "WiFi";
 			linux,code = <KEY_RFKILL>;
 			gpios = <&chipcommon 5 GPIO_ACTIVE_LOW>;
 		};
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 6 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/bcm4708-netgear-r6300-v2.dts b/arch/arm/boot/dts/bcm4708-netgear-r6300-v2.dts
index 4c60eda296d9..76fc1099d47d 100644
--- a/arch/arm/boot/dts/bcm4708-netgear-r6300-v2.dts
+++ b/arch/arm/boot/dts/bcm4708-netgear-r6300-v2.dts
@@ -59,19 +59,19 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		wps {
+		button-wps {
 			label = "WPS";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&chipcommon 4 GPIO_ACTIVE_LOW>;
 		};
 
-		rfkill {
+		button-rfkill {
 			label = "WiFi";
 			linux,code = <KEY_RFKILL>;
 			gpios = <&chipcommon 5 GPIO_ACTIVE_LOW>;
 		};
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 6 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/bcm4708-smartrg-sr400ac.dts b/arch/arm/boot/dts/bcm4708-smartrg-sr400ac.dts
index 9ca6d1b2590d..6bcdfb73cb9e 100644
--- a/arch/arm/boot/dts/bcm4708-smartrg-sr400ac.dts
+++ b/arch/arm/boot/dts/bcm4708-smartrg-sr400ac.dts
@@ -94,19 +94,19 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		rfkill {
+		button-rfkill {
 			label = "WiFi";
 			linux,code = <KEY_RFKILL>;
 			gpios = <&chipcommon 0 GPIO_ACTIVE_LOW>;
 		};
 
-		wps {
+		button-wps {
 			label = "WPS";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&chipcommon 7 GPIO_ACTIVE_LOW>;
 		};
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/bcm47081-asus-rt-n18u.dts b/arch/arm/boot/dts/bcm47081-asus-rt-n18u.dts
index 0e273c598732..ca47cc4f2ba1 100644
--- a/arch/arm/boot/dts/bcm47081-asus-rt-n18u.dts
+++ b/arch/arm/boot/dts/bcm47081-asus-rt-n18u.dts
@@ -60,13 +60,13 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 7 GPIO_ACTIVE_LOW>;
 		};
 
-		wps {
+		button-wps {
 			label = "WPS";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/bcm47081-buffalo-wzr-600dhp2.dts b/arch/arm/boot/dts/bcm47081-buffalo-wzr-600dhp2.dts
index d00495a8b6fc..0edc2543e568 100644
--- a/arch/arm/boot/dts/bcm47081-buffalo-wzr-600dhp2.dts
+++ b/arch/arm/boot/dts/bcm47081-buffalo-wzr-600dhp2.dts
@@ -91,26 +91,26 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		aoss {
+		button-aoss {
 			label = "AOSS";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&chipcommon 9 GPIO_ACTIVE_LOW>;
 		};
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
 		};
 
 		/* Switch device mode? */
-		mode {
+		button-mode {
 			label = "Mode";
 			linux,code = <KEY_SETUP>;
 			gpios = <&chipcommon 14 GPIO_ACTIVE_LOW>;
 		};
 
-		eject {
+		button-eject {
 			label = "USB eject";
 			linux,code = <KEY_EJECTCD>;
 			gpios = <&chipcommon 15 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/bcm47081-buffalo-wzr-900dhp.dts b/arch/arm/boot/dts/bcm47081-buffalo-wzr-900dhp.dts
index 8b1a05a0f1a1..1f0998f34afd 100644
--- a/arch/arm/boot/dts/bcm47081-buffalo-wzr-900dhp.dts
+++ b/arch/arm/boot/dts/bcm47081-buffalo-wzr-900dhp.dts
@@ -96,7 +96,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/bcm47081-luxul-xap-1410.dts b/arch/arm/boot/dts/bcm47081-luxul-xap-1410.dts
index 68aaf0af3945..c8c02377543b 100644
--- a/arch/arm/boot/dts/bcm47081-luxul-xap-1410.dts
+++ b/arch/arm/boot/dts/bcm47081-luxul-xap-1410.dts
@@ -45,7 +45,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/bcm47081-luxul-xwr-1200.dts b/arch/arm/boot/dts/bcm47081-luxul-xwr-1200.dts
index 9316a36434f7..3b35a7af4b1c 100644
--- a/arch/arm/boot/dts/bcm47081-luxul-xwr-1200.dts
+++ b/arch/arm/boot/dts/bcm47081-luxul-xwr-1200.dts
@@ -94,7 +94,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/bcm47081-tplink-archer-c5-v2.dts b/arch/arm/boot/dts/bcm47081-tplink-archer-c5-v2.dts
index 12e34a0439b4..19a7971b5a00 100644
--- a/arch/arm/boot/dts/bcm47081-tplink-archer-c5-v2.dts
+++ b/arch/arm/boot/dts/bcm47081-tplink-archer-c5-v2.dts
@@ -77,13 +77,13 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		rfkill {
+		button-rfkill {
 			label = "WiFi";
 			linux,code = <KEY_RFKILL>;
 			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
 		};
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 7 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/bcm4709-asus-rt-ac87u.dts b/arch/arm/boot/dts/bcm4709-asus-rt-ac87u.dts
index 7546c8d07bcd..f52a75c4ca09 100644
--- a/arch/arm/boot/dts/bcm4709-asus-rt-ac87u.dts
+++ b/arch/arm/boot/dts/bcm4709-asus-rt-ac87u.dts
@@ -47,16 +47,14 @@
 
 	gpio-keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 
-		wps {
+		button-wps {
 			label = "WPS";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&chipcommon 2 GPIO_ACTIVE_LOW>;
 		};
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/bcm4709-buffalo-wxr-1900dhp.dts b/arch/arm/boot/dts/bcm4709-buffalo-wxr-1900dhp.dts
index beae9eab9cb8..5ff6c588e16e 100644
--- a/arch/arm/boot/dts/bcm4709-buffalo-wxr-1900dhp.dts
+++ b/arch/arm/boot/dts/bcm4709-buffalo-wxr-1900dhp.dts
@@ -77,42 +77,40 @@
 
 	gpio-keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 
-		power {
+		button-power {
 			label = "Power";
 			linux,code = <KEY_POWER>;
 			gpios = <&chipcommon 1 GPIO_ACTIVE_LOW>;
 		};
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 15 GPIO_ACTIVE_LOW>;
 		};
 
-		aoss {
+		button-aoss {
 			label = "AOSS";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&chipcommon 16 GPIO_ACTIVE_LOW>;
 		};
 
 		/* Commit mode set by switch? */
-		mode {
+		button-mode {
 			label = "Mode";
 			linux,code = <KEY_SETUP>;
 			gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>;
 		};
 
 		/* Switch: AP mode */
-		sw_ap {
+		button-sw-ap {
 			label = "AP";
 			linux,code = <BTN_0>;
 			gpios = <&chipcommon 18 GPIO_ACTIVE_LOW>;
 		};
 
-		eject {
+		button-eject {
 			label = "USB eject";
 			linux,code = <KEY_EJECTCD>;
 			gpios = <&chipcommon 20 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/bcm4709-linksys-ea9200.dts b/arch/arm/boot/dts/bcm4709-linksys-ea9200.dts
index 7879f7d7d9c3..99253fd7adb3 100644
--- a/arch/arm/boot/dts/bcm4709-linksys-ea9200.dts
+++ b/arch/arm/boot/dts/bcm4709-linksys-ea9200.dts
@@ -29,16 +29,14 @@
 
 	gpio-keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 
-		wps {
+		button-wps {
 			label = "WPS";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
 		};
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/bcm4709-netgear-r7000.dts b/arch/arm/boot/dts/bcm4709-netgear-r7000.dts
index 56d309dbc6b0..de961fbb6200 100644
--- a/arch/arm/boot/dts/bcm4709-netgear-r7000.dts
+++ b/arch/arm/boot/dts/bcm4709-netgear-r7000.dts
@@ -72,22 +72,20 @@
 
 	gpio-keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 
-		wps {
+		button-wps {
 			label = "WPS";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&chipcommon 4 GPIO_ACTIVE_LOW>;
 		};
 
-		rfkill {
+		button-rfkill {
 			label = "WiFi";
 			linux,code = <KEY_RFKILL>;
 			gpios = <&chipcommon 5 GPIO_ACTIVE_LOW>;
 		};
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 6 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/bcm4709-netgear-r8000.dts b/arch/arm/boot/dts/bcm4709-netgear-r8000.dts
index 89f992af61d1..087f7f60de18 100644
--- a/arch/arm/boot/dts/bcm4709-netgear-r8000.dts
+++ b/arch/arm/boot/dts/bcm4709-netgear-r8000.dts
@@ -99,28 +99,26 @@
 
 	gpio-keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 
-		rfkill {
+		button-rfkill {
 			label = "WiFi";
 			linux,code = <KEY_RFKILL>;
 			gpios = <&chipcommon 4 GPIO_ACTIVE_LOW>;
 		};
 
-		wps {
+		button-wps {
 			label = "WPS";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&chipcommon 5 GPIO_ACTIVE_LOW>;
 		};
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 6 GPIO_ACTIVE_LOW>;
 		};
 
-		brightness {
+		button-brightness {
 			label = "Backlight";
 			linux,code = <KEY_BRIGHTNESS_ZERO>;
 			gpios = <&chipcommon 19 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/bcm4709-tplink-archer-c9-v1.dts b/arch/arm/boot/dts/bcm4709-tplink-archer-c9-v1.dts
index c2a266a439d0..11d1068160da 100644
--- a/arch/arm/boot/dts/bcm4709-tplink-archer-c9-v1.dts
+++ b/arch/arm/boot/dts/bcm4709-tplink-archer-c9-v1.dts
@@ -77,16 +77,14 @@
 
 	gpio-keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 
-		wps {
+		button-wps {
 			label = "WPS";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&chipcommon 0 GPIO_ACTIVE_LOW>;
 		};
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/bcm47094-asus-rt-ac88u.dts b/arch/arm/boot/dts/bcm47094-asus-rt-ac88u.dts
index 448060561cd0..a5fec56d11c0 100644
--- a/arch/arm/boot/dts/bcm47094-asus-rt-ac88u.dts
+++ b/arch/arm/boot/dts/bcm47094-asus-rt-ac88u.dts
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
 /*
- * Copyright (C) 2021 Arınç ÜNAL <arinc.unal@arinc9.com>
+ * Copyright (C) 2021-2022 Arınç ÜNAL <arinc.unal@arinc9.com>
  */
 
 /dts-v1/;
@@ -25,6 +25,9 @@
 	nvram@1c080000 {
 		compatible = "brcm,nvram";
 		reg = <0x1c080000 0x00180000>;
+
+		et1macaddr: et1macaddr {
+		};
 	};
 
 	leds {
@@ -68,33 +71,107 @@
 
 	gpio-keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 
-		wps {
+		button-wps {
 			label = "WPS";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&chipcommon 20 GPIO_ACTIVE_LOW>;
 		};
 
-		reset {
+		button-reset {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
 		};
 
-		wifi {
+		button-wifi {
 			label = "Wi-Fi";
 			linux,code = <KEY_RFKILL>;
 			gpios = <&chipcommon 18 GPIO_ACTIVE_LOW>;
 		};
 
-		led {
+		button-led {
 			label = "Backlight";
 			linux,code = <KEY_BRIGHTNESS_ZERO>;
 			gpios = <&chipcommon 4 GPIO_ACTIVE_LOW>;
 		};
 	};
+
+	switch {
+		compatible = "realtek,rtl8365mb";
+		/* 7 = MDIO (has input reads), 6 = MDC (clock, output only) */
+		mdc-gpios = <&chipcommon 6 GPIO_ACTIVE_HIGH>;
+		mdio-gpios = <&chipcommon 7 GPIO_ACTIVE_HIGH>;
+		reset-gpios = <&chipcommon 10 GPIO_ACTIVE_LOW>;
+		realtek,disable-leds;
+		dsa,member = <1 0>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				label = "lan5";
+				phy-handle = <&ethphy0>;
+			};
+
+			port@1 {
+				reg = <1>;
+				label = "lan6";
+				phy-handle = <&ethphy1>;
+			};
+
+			port@2 {
+				reg = <2>;
+				label = "lan7";
+				phy-handle = <&ethphy2>;
+			};
+
+			port@3 {
+				reg = <3>;
+				label = "lan8";
+				phy-handle = <&ethphy3>;
+			};
+
+			port@6 {
+				reg = <6>;
+				label = "cpu";
+				ethernet = <&sw0_p5>;
+				phy-mode = "rgmii";
+				tx-internal-delay-ps = <2000>;
+				rx-internal-delay-ps = <2100>;
+
+				fixed-link {
+					speed = <1000>;
+					full-duplex;
+					pause;
+				};
+			};
+		};
+
+		mdio {
+			compatible = "realtek,smi-mdio";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			ethphy0: ethernet-phy@0 {
+				reg = <0>;
+			};
+
+			ethphy1: ethernet-phy@1 {
+				reg = <1>;
+			};
+
+			ethphy2: ethernet-phy@2 {
+				reg = <2>;
+			};
+
+			ethphy3: ethernet-phy@3 {
+				reg = <3>;
+			};
+		};
+	};
 };
 
 &srab {
@@ -103,9 +180,6 @@
 	dsa,member = <0 0>;
 
 	ports {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
 		port@0 {
 			reg = <0>;
 			label = "lan4";
@@ -134,10 +208,12 @@
 		sw0_p5: port@5 {
 			reg = <5>;
 			label = "extsw";
+			phy-mode = "rgmii";
 
 			fixed-link {
 				speed = <1000>;
 				full-duplex;
+				pause;
 			};
 		};
 
@@ -156,7 +232,6 @@
 			reg = <8>;
 			ethernet = <&gmac2>;
 			label = "cpu";
-			status = "disabled";
 
 			fixed-link {
 				speed = <1000>;
@@ -166,6 +241,15 @@
 	};
 };
 
+&gmac0 {
+	status = "disabled";
+};
+
+&gmac1 {
+	nvmem-cells = <&et1macaddr>;
+	nvmem-cell-names = "mac-address";
+};
+
 &usb2 {
 	vcc-gpio = <&chipcommon 9 GPIO_ACTIVE_HIGH>;
 };
diff --git a/arch/arm/boot/dts/bcm47094-dlink-dir-885l.dts b/arch/arm/boot/dts/bcm47094-dlink-dir-885l.dts
index 60bfd52ee677..2c38b642a8b8 100644
--- a/arch/arm/boot/dts/bcm47094-dlink-dir-885l.dts
+++ b/arch/arm/boot/dts/bcm47094-dlink-dir-885l.dts
@@ -86,20 +86,20 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		wps {
+		button-wps {
 			label = "WPS";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&chipcommon 7 GPIO_ACTIVE_LOW>;
 		};
 
 		/* Switch: router / extender */
-		extender {
+		button-extender {
 			label = "Extender";
 			linux,code = <BTN_0>;
 			gpios = <&chipcommon 10 GPIO_ACTIVE_LOW>;
 		};
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/bcm47094-linksys-panamera.dts b/arch/arm/boot/dts/bcm47094-linksys-panamera.dts
index 9bef6b9bfa8d..86c7cc0fa70e 100644
--- a/arch/arm/boot/dts/bcm47094-linksys-panamera.dts
+++ b/arch/arm/boot/dts/bcm47094-linksys-panamera.dts
@@ -30,19 +30,19 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		wps {
+		button-wps {
 			label = "WPS";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
 		};
 
-		rfkill {
+		button-rfkill {
 				label = "WiFi";
 				linux,code = <KEY_RFKILL>;
 				gpios = <&chipcommon 16 GPIO_ACTIVE_LOW>;
 		};
 
-		reset {
+		button-reset {
 				label = "Reset";
 				linux,code = <KEY_RESTART>;
 				gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/bcm47094-luxul-abr-4500.dts b/arch/arm/boot/dts/bcm47094-luxul-abr-4500.dts
index b51a0ee7e584..9ad15bcae1ca 100644
--- a/arch/arm/boot/dts/bcm47094-luxul-abr-4500.dts
+++ b/arch/arm/boot/dts/bcm47094-luxul-abr-4500.dts
@@ -49,7 +49,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/bcm47094-luxul-xap-1610.dts b/arch/arm/boot/dts/bcm47094-luxul-xap-1610.dts
index 6fa101f0a90d..ee24d3768536 100644
--- a/arch/arm/boot/dts/bcm47094-luxul-xap-1610.dts
+++ b/arch/arm/boot/dts/bcm47094-luxul-xap-1610.dts
@@ -43,7 +43,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/bcm47094-luxul-xbr-4500.dts b/arch/arm/boot/dts/bcm47094-luxul-xbr-4500.dts
index b959a9504eea..6549d07b9887 100644
--- a/arch/arm/boot/dts/bcm47094-luxul-xbr-4500.dts
+++ b/arch/arm/boot/dts/bcm47094-luxul-xbr-4500.dts
@@ -49,7 +49,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/bcm47094-luxul-xwc-2000.dts b/arch/arm/boot/dts/bcm47094-luxul-xwc-2000.dts
index b0d8a688141d..654fcce9fded 100644
--- a/arch/arm/boot/dts/bcm47094-luxul-xwc-2000.dts
+++ b/arch/arm/boot/dts/bcm47094-luxul-xwc-2000.dts
@@ -34,10 +34,8 @@
 
 	gpio-keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 19 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/bcm47094-luxul-xwr-3100.dts b/arch/arm/boot/dts/bcm47094-luxul-xwr-3100.dts
index cbe8c8e4a301..bf053a2fcc7c 100644
--- a/arch/arm/boot/dts/bcm47094-luxul-xwr-3100.dts
+++ b/arch/arm/boot/dts/bcm47094-luxul-xwr-3100.dts
@@ -89,7 +89,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/bcm47094-luxul-xwr-3150-v1.dts b/arch/arm/boot/dts/bcm47094-luxul-xwr-3150-v1.dts
index 24ae3c8a3e09..78a90dd57a4e 100644
--- a/arch/arm/boot/dts/bcm47094-luxul-xwr-3150-v1.dts
+++ b/arch/arm/boot/dts/bcm47094-luxul-xwr-3150-v1.dts
@@ -25,6 +25,9 @@
 	nvram@1eff0000 {
 		compatible = "brcm,nvram";
 		reg = <0x1eff0000 0x10000>;
+
+		et0macaddr: et0macaddr {
+		};
 	};
 
 	leds {
@@ -64,7 +67,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>;
@@ -72,6 +75,11 @@
 	};
 };
 
+&gmac0 {
+	nvmem-cells = <&et0macaddr>;
+	nvmem-cell-names = "mac-address";
+};
+
 &usb3 {
 	vcc-gpio = <&chipcommon 18 GPIO_ACTIVE_HIGH>;
 };
diff --git a/arch/arm/boot/dts/bcm47094-netgear-r8500.dts b/arch/arm/boot/dts/bcm47094-netgear-r8500.dts
index 42097a4c2659..f850dce37b20 100644
--- a/arch/arm/boot/dts/bcm47094-netgear-r8500.dts
+++ b/arch/arm/boot/dts/bcm47094-netgear-r8500.dts
@@ -65,25 +65,25 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		brightness {
+		button-brightness {
 			label = "Backlight";
 			linux,code = <KEY_BRIGHTNESS_ZERO>;
 			gpios = <&chipcommon 1 GPIO_ACTIVE_LOW>;
 		};
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 10 GPIO_ACTIVE_LOW>;
 		};
 
-		wps {
+		button-wps {
 			label = "WPS";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&chipcommon 14 GPIO_ACTIVE_LOW>;
 		};
 
-		rfkill {
+		button-rfkill {
 			label = "WiFi";
 			linux,code = <KEY_RFKILL>;
 			gpios = <&chipcommon 20 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/bcm47094-phicomm-k3.dts b/arch/arm/boot/dts/bcm47094-phicomm-k3.dts
index a2566ad4619c..3bf6e24978ac 100644
--- a/arch/arm/boot/dts/bcm47094-phicomm-k3.dts
+++ b/arch/arm/boot/dts/bcm47094-phicomm-k3.dts
@@ -22,7 +22,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 17 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/bcm47189-luxul-xap-1440.dts b/arch/arm/boot/dts/bcm47189-luxul-xap-1440.dts
index 57ca1cfaecd8..e20b6d2eb274 100644
--- a/arch/arm/boot/dts/bcm47189-luxul-xap-1440.dts
+++ b/arch/arm/boot/dts/bcm47189-luxul-xap-1440.dts
@@ -39,7 +39,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 7 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/bcm47189-luxul-xap-810.dts b/arch/arm/boot/dts/bcm47189-luxul-xap-810.dts
index 2e1a7e382cb7..9d863570fcf3 100644
--- a/arch/arm/boot/dts/bcm47189-luxul-xap-810.dts
+++ b/arch/arm/boot/dts/bcm47189-luxul-xap-810.dts
@@ -49,7 +49,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 7 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/bcm47189-tenda-ac9.dts b/arch/arm/boot/dts/bcm47189-tenda-ac9.dts
index 07eb3a8287d6..55b92645b0f1 100644
--- a/arch/arm/boot/dts/bcm47189-tenda-ac9.dts
+++ b/arch/arm/boot/dts/bcm47189-tenda-ac9.dts
@@ -59,19 +59,19 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		rfkill {
+		button-rfkill {
 			label = "WiFi";
 			linux,code = <KEY_RFKILL>;
 			gpios = <&chipcommon 3 GPIO_ACTIVE_LOW>;
 		};
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 7 GPIO_ACTIVE_LOW>;
 		};
 
-		wps {
+		button-wps {
 			label = "WPS";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&chipcommon 9 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/bcm47622.dtsi b/arch/arm/boot/dts/bcm47622.dtsi
new file mode 100644
index 000000000000..2df04528af82
--- /dev/null
+++ b/arch/arm/boot/dts/bcm47622.dtsi
@@ -0,0 +1,130 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2022 Broadcom Ltd.
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	compatible = "brcm,bcm47622", "brcm,bcmbca";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	interrupt-parent = <&gic>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		CA7_0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x0>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		CA7_1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x1>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		CA7_2: cpu@2 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x2>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		CA7_3: cpu@3 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x3>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		L2_0: l2-cache0 {
+			compatible = "cache";
+		};
+	};
+
+	timer {
+		compatible = "arm,armv7-timer";
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+		arm,cpu-registers-not-fw-configured;
+	};
+
+	pmu: pmu {
+		compatible = "arm,cortex-a7-pmu";
+		interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&CA7_0>, <&CA7_1>,
+			<&CA7_2>, <&CA7_3>;
+	};
+
+	clocks: clocks {
+		periph_clk: periph-clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <200000000>;
+		};
+
+		uart_clk: uart-clk {
+			compatible = "fixed-factor-clock";
+			#clock-cells = <0>;
+			clocks = <&periph_clk>;
+			clock-div = <4>;
+			clock-mult = <1>;
+		};
+	};
+
+	psci {
+		compatible = "arm,psci-0.2";
+		method = "smc";
+	};
+
+	axi@81000000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0x81000000 0x8000>;
+
+		gic: interrupt-controller@1000 {
+			compatible = "arm,cortex-a7-gic";
+			#interrupt-cells = <3>;
+			interrupt-controller;
+			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+			reg = <0x1000 0x1000>,
+				<0x2000 0x2000>,
+				<0x4000 0x2000>,
+				<0x6000 0x2000>;
+		};
+	};
+
+	bus@ff800000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0xff800000 0x800000>;
+
+		uart0: serial@12000 {
+			compatible = "arm,pl011", "arm,primecell";
+			reg = <0x12000 0x1000>;
+			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&uart_clk>, <&uart_clk>;
+			clock-names = "uartclk", "apb_pclk";
+			status = "disabled";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/bcm53015-meraki-mr26.dts b/arch/arm/boot/dts/bcm53015-meraki-mr26.dts
new file mode 100644
index 000000000000..14f58033efeb
--- /dev/null
+++ b/arch/arm/boot/dts/bcm53015-meraki-mr26.dts
@@ -0,0 +1,166 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Broadcom BCM470X / BCM5301X ARM platform code.
+ * DTS for Meraki MR26 / Codename: Venom
+ *
+ * Copyright (C) 2022 Christian Lamparter <chunkeey@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "bcm4708.dtsi"
+#include "bcm5301x-nand-cs0-bch8.dtsi"
+#include <dt-bindings/leds/common.h>
+
+/ {
+	compatible = "meraki,mr26", "brcm,bcm53015", "brcm,bcm4708";
+	model = "Meraki MR26";
+
+	memory@0 {
+		reg = <0x00000000 0x08000000>;
+		device_type = "memory";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-0 {
+			function = LED_FUNCTION_FAULT;
+			color = <LED_COLOR_ID_AMBER>;
+			gpios = <&chipcommon 13 GPIO_ACTIVE_HIGH>;
+			panic-indicator;
+		};
+		led-1 {
+			function = LED_FUNCTION_INDICATOR;
+			color = <LED_COLOR_ID_WHITE>;
+			gpios = <&chipcommon 12 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		key-restart {
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&chipcommon 11 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&uart0 {
+	clock-frequency = <50000000>;
+	/delete-property/ clocks;
+};
+
+&uart1 {
+	status = "disabled";
+};
+
+&gmac0 {
+	status = "okay";
+};
+
+&gmac1 {
+	status = "disabled";
+};
+&gmac2 {
+	status = "disabled";
+};
+&gmac3 {
+	status = "disabled";
+};
+
+&nandcs {
+	nand-ecc-algo = "hw";
+
+	partitions {
+		compatible = "fixed-partitions";
+		#address-cells = <0x1>;
+		#size-cells = <0x1>;
+
+		partition@0 {
+			label = "u-boot";
+			reg = <0x0 0x200000>;
+			read-only;
+		};
+
+		partition@200000 {
+			label = "u-boot-env";
+			reg = <0x200000 0x200000>;
+			/* empty */
+		};
+
+		partition@400000 {
+			label = "u-boot-backup";
+			reg = <0x400000 0x200000>;
+			/* empty */
+		};
+
+		partition@600000 {
+			label = "u-boot-env-backup";
+			reg = <0x600000 0x200000>;
+			/* empty */
+		};
+
+		partition@800000 {
+			label = "ubi";
+			reg = <0x800000 0x7780000>;
+		};
+	};
+};
+
+&srab {
+	status = "okay";
+
+	ports {
+		port@0 {
+			reg = <0>;
+			label = "poe";
+		};
+
+		port@5 {
+			reg = <5>;
+			label = "cpu";
+			ethernet = <&gmac0>;
+
+			fixed-link {
+				speed = <1000>;
+				duplex-full;
+			};
+		};
+	};
+};
+
+&i2c0 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinmux_i2c>;
+
+	clock-frequency = <100000>;
+
+	ina219@40 {
+		compatible = "ti,ina219"; /* PoE power */
+		reg = <0x40>;
+		shunt-resistor = <60000>; /* = 60 mOhms */
+	};
+
+	eeprom@56 {
+		compatible = "atmel,24c64";
+		reg = <0x56>;
+		pagesize = <32>;
+		read-only;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		/* it's empty */
+	};
+};
+
+&thermal {
+	status = "disabled";
+	/* does not work, reads 418 degree Celsius */
+};
diff --git a/arch/arm/boot/dts/bcm53016-meraki-mr32.dts b/arch/arm/boot/dts/bcm53016-meraki-mr32.dts
index 64f973e1ef12..e678bc03d816 100644
--- a/arch/arm/boot/dts/bcm53016-meraki-mr32.dts
+++ b/arch/arm/boot/dts/bcm53016-meraki-mr32.dts
@@ -13,7 +13,7 @@
 #include <dt-bindings/leds/common.h>
 
 / {
-	compatible = "meraki,mr32", "brcm,brcm53016", "brcm,bcm4708";
+	compatible = "meraki,mr32", "brcm,bcm53016", "brcm,bcm4708";
 	model = "Meraki MR32";
 
 	chosen {
@@ -47,10 +47,8 @@
 
 	keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 21 GPIO_ACTIVE_LOW>;
@@ -84,40 +82,6 @@
 			max-brightness = <255>;
 		};
 	};
-
-	i2c {
-		/*
-		 * The platform provided I2C does not budge.
-		 * This is a replacement until I can figure
-		 * out what are the missing bits...
-		 */
-
-		compatible = "i2c-gpio";
-		sda-gpios = <&chipcommon 5 GPIO_ACTIVE_HIGH>;
-		scl-gpios = <&chipcommon 4 GPIO_ACTIVE_HIGH>;
-		i2c-gpio,delay-us = <10>; /* close to 100 kHz */
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		current_sense: ina219@45 {
-			compatible = "ti,ina219";
-			reg = <0x45>;
-			shunt-resistor = <60000>; /* = 60 mOhms */
-		};
-
-		eeprom: eeprom@50 {
-			compatible = "atmel,24c64";
-			reg = <0x50>;
-			pagesize = <32>;
-			read-only;
-			#address-cells = <1>;
-			#size-cells = <1>;
-
-			mac_address: mac-address@66 {
-				reg = <0x66 0x6>;
-			};
-		};
-	};
 };
 
 &uart0 {
@@ -228,3 +192,31 @@
 		};
 	};
 };
+
+&i2c0 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinmux_i2c>;
+
+	clock-frequency = <100000>;
+
+	current_sense: ina219@45 {
+		compatible = "ti,ina219";
+		reg = <0x45>;
+		shunt-resistor = <60000>; /* = 60 mOhms */
+	};
+
+	eeprom: eeprom@50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+		pagesize = <32>;
+		read-only;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		mac_address: mac-address@66 {
+			reg = <0x66 0x6>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/bcm5301x.dtsi b/arch/arm/boot/dts/bcm5301x.dtsi
index f69d2af3c1fa..5fc1b847f4aa 100644
--- a/arch/arm/boot/dts/bcm5301x.dtsi
+++ b/arch/arm/boot/dts/bcm5301x.dtsi
@@ -148,15 +148,6 @@
 		};
 	};
 
-	usb2_phy: usb2-phy@1800c000 {
-		compatible = "brcm,ns-usb2-phy";
-		reg = <0x1800c000 0x1000>;
-		reg-names = "dmu";
-		#phy-cells = <0>;
-		clocks = <&genpll BCM_NSP_GENPLL_USB_PHY_REF_CLK>;
-		clock-names = "phy-ref-clk";
-	};
-
 	axi@18000000 {
 		compatible = "brcm,bus-axi";
 		reg = <0x18000000 0x1000>;
@@ -423,14 +414,14 @@
 		#address-cells = <1>;
 		#size-cells = <1>;
 
-		cru@100 {
-			compatible = "simple-bus";
+		cru-bus@100 {
+			compatible = "brcm,ns-cru", "simple-mfd";
 			reg = <0x100 0x1a4>;
 			ranges;
 			#address-cells = <1>;
 			#size-cells = <1>;
 
-			lcpll0: lcpll0@100 {
+			lcpll0: clock-controller@100 {
 				#clock-cells = <1>;
 				compatible = "brcm,nsp-lcpll0";
 				reg = <0x100 0x14>;
@@ -439,7 +430,7 @@
 						     "sdio", "ddr_phy";
 			};
 
-			genpll: genpll@140 {
+			genpll: clock-controller@140 {
 				#clock-cells = <1>;
 				compatible = "brcm,nsp-genpll";
 				reg = <0x140 0x24>;
@@ -450,7 +441,21 @@
 						     "sata1", "sata2";
 			};
 
-			pinctrl: pin-controller@1c0 {
+			usb2_phy: phy@164 {
+				compatible = "brcm,ns-usb2-phy";
+				reg = <0x164 0x4>;
+				brcm,syscon-clkset = <&cru_clkset>;
+				clocks = <&genpll BCM_NSP_GENPLL_USB_PHY_REF_CLK>;
+				clock-names = "phy-ref-clk";
+				#phy-cells = <0>;
+			};
+
+			cru_clkset: syscon@180 {
+				compatible = "brcm,cru-clkset", "syscon";
+				reg = <0x180 0x4>;
+			};
+
+			pinctrl: pinctrl@1c0 {
 				compatible = "brcm,bcm4708-pinmux";
 				reg = <0x1c0 0x24>;
 				reg-names = "cru_gpio_control";
@@ -563,9 +568,9 @@
 
 			trips {
 				cpu-crit {
-					temperature	= <125000>;
-					hysteresis	= <0>;
-					type		= "critical";
+					temperature = <125000>;
+					hysteresis = <0>;
+					type = "critical";
 				};
 			};
 
diff --git a/arch/arm/boot/dts/bcm53340-ubnt-unifi-switch8.dts b/arch/arm/boot/dts/bcm53340-ubnt-unifi-switch8.dts
index 2e7fda9b998c..975f854f652f 100644
--- a/arch/arm/boot/dts/bcm53340-ubnt-unifi-switch8.dts
+++ b/arch/arm/boot/dts/bcm53340-ubnt-unifi-switch8.dts
@@ -34,7 +34,7 @@
 	status = "okay";
 	bspi-sel = <0>;
 
-	flash: m25p80@0 {
+	flash: flash@0 {
 		compatible = "m25p80";
 		reg = <0>;
 		#address-cells = <1>;
diff --git a/arch/arm/boot/dts/bcm63138.dtsi b/arch/arm/boot/dts/bcm63138.dtsi
index cca49a2e2d62..b774a8d63813 100644
--- a/arch/arm/boot/dts/bcm63138.dtsi
+++ b/arch/arm/boot/dts/bcm63138.dtsi
@@ -9,8 +9,8 @@
 / {
 	#address-cells = <1>;
 	#size-cells = <1>;
-	compatible = "brcm,bcm63138";
-	model = "Broadcom BCM63138 DSL SoC";
+	compatible = "brcm,bcm63138", "brcm,bcmbca";
+	model = "Broadcom BCM963138 Reference Board";
 	interrupt-parent = <&gic>;
 
 	aliases {
diff --git a/arch/arm/boot/dts/bcm63148.dtsi b/arch/arm/boot/dts/bcm63148.dtsi
new file mode 100644
index 000000000000..df5307b6b3af
--- /dev/null
+++ b/arch/arm/boot/dts/bcm63148.dtsi
@@ -0,0 +1,103 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2022 Broadcom Ltd.
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	compatible = "brcm,bcm63148", "brcm,bcmbca";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	interrupt-parent = <&gic>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		B15_0: cpu@0 {
+			device_type = "cpu";
+			compatible = "brcm,brahma-b15";
+			reg = <0x0>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		B15_1: cpu@1 {
+			device_type = "cpu";
+			compatible = "brcm,brahma-b15";
+			reg = <0x1>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		L2_0: l2-cache0 {
+			compatible = "cache";
+		};
+	};
+
+	timer {
+		compatible = "arm,armv7-timer";
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>;
+	};
+
+	pmu: pmu {
+		compatible = "arm,cortex-a15-pmu";
+		interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&B15_0>, <&B15_1>;
+	};
+
+	clocks: clocks {
+		periph_clk: periph-clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <50000000>;
+		};
+	};
+
+	psci {
+		compatible = "arm,psci-0.2";
+		method = "smc";
+	};
+
+	axi@80030000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0x80030000 0x8000>;
+
+		gic: interrupt-controller@1000 {
+			compatible = "arm,cortex-a15-gic";
+			#interrupt-cells = <3>;
+			interrupt-controller;
+			reg = <0x1000 0x1000>,
+				<0x2000 0x2000>,
+				<0x4000 0x2000>,
+				<0x6000 0x2000>;
+			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(2) |
+					IRQ_TYPE_LEVEL_HIGH)>;
+		};
+	};
+
+	bus@ff800000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0xfffe8000 0x8000>;
+
+		uart0: serial@600 {
+			compatible = "brcm,bcm6345-uart";
+			reg = <0x600 0x20>;
+			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&periph_clk>;
+			clock-names = "refclk";
+			status = "disabled";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/bcm63178.dtsi b/arch/arm/boot/dts/bcm63178.dtsi
new file mode 100644
index 000000000000..cbd094dde6d0
--- /dev/null
+++ b/arch/arm/boot/dts/bcm63178.dtsi
@@ -0,0 +1,120 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2022 Broadcom Ltd.
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	compatible = "brcm,bcm63178", "brcm,bcmbca";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	interrupt-parent = <&gic>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		CA7_0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x0>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		CA7_1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x1>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		CA7_2: cpu@2 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x2>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		L2_0: l2-cache0 {
+			compatible = "cache";
+		};
+	};
+
+	timer {
+		compatible = "arm,armv7-timer";
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(3) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(3) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(3) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(3) | IRQ_TYPE_LEVEL_LOW)>;
+		arm,cpu-registers-not-fw-configured;
+	};
+
+	pmu: pmu {
+		compatible = "arm,cortex-a7-pmu";
+		interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&CA7_0>, <&CA7_1>,
+			<&CA7_2>;
+	};
+
+	clocks: clocks {
+		periph_clk: periph-clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <200000000>;
+		};
+		uart_clk: uart-clk {
+			compatible = "fixed-factor-clock";
+			#clock-cells = <0>;
+			clocks = <&periph_clk>;
+			clock-div = <4>;
+			clock-mult = <1>;
+		};
+	};
+
+	psci {
+		compatible = "arm,psci-0.2";
+		method = "smc";
+	};
+
+	axi@81000000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0x81000000 0x8000>;
+
+		gic: interrupt-controller@1000 {
+			compatible = "arm,cortex-a7-gic";
+			#interrupt-cells = <3>;
+			interrupt-controller;
+			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(3) | IRQ_TYPE_LEVEL_HIGH)>;
+			reg = <0x1000 0x1000>,
+				<0x2000 0x2000>,
+				<0x4000 0x2000>,
+				<0x6000 0x2000>;
+		};
+	};
+
+	bus@ff800000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0xff800000 0x800000>;
+
+		uart0: serial@12000 {
+			compatible = "arm,pl011", "arm,primecell";
+			reg = <0x12000 0x1000>;
+			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&uart_clk>, <&uart_clk>;
+			clock-names = "uartclk", "apb_pclk";
+			status = "disabled";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/bcm6756.dtsi b/arch/arm/boot/dts/bcm6756.dtsi
new file mode 100644
index 000000000000..ce1b59faf800
--- /dev/null
+++ b/arch/arm/boot/dts/bcm6756.dtsi
@@ -0,0 +1,130 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2022 Broadcom Ltd.
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	compatible = "brcm,bcm6756", "brcm,bcmbca";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	interrupt-parent = <&gic>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		CA7_0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x0>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		CA7_1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x1>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		CA7_2: cpu@2 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x2>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		CA7_3: cpu@3 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x3>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		L2_0: l2-cache0 {
+			compatible = "cache";
+		};
+	};
+
+	timer {
+		compatible = "arm,armv7-timer";
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+		arm,cpu-registers-not-fw-configured;
+	};
+
+	pmu: pmu {
+		compatible = "arm,cortex-a7-pmu";
+		interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&CA7_0>, <&CA7_1>,
+			<&CA7_2>, <&CA7_3>;
+	};
+
+	clocks: clocks {
+		periph_clk: periph-clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <200000000>;
+		};
+
+		uart_clk: uart-clk {
+			compatible = "fixed-factor-clock";
+			#clock-cells = <0>;
+			clocks = <&periph_clk>;
+			clock-div = <4>;
+			clock-mult = <1>;
+		};
+	};
+
+	psci {
+		compatible = "arm,psci-0.2";
+		method = "smc";
+	};
+
+	axi@81000000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0x81000000 0x8000>;
+
+		gic: interrupt-controller@1000 {
+			compatible = "arm,cortex-a7-gic";
+			#interrupt-cells = <3>;
+			interrupt-controller;
+			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+			reg = <0x1000 0x1000>,
+				<0x2000 0x2000>,
+				<0x4000 0x2000>,
+				<0x6000 0x2000>;
+		};
+	};
+
+	bus@ff800000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0xff800000 0x800000>;
+
+		uart0: serial@12000 {
+			compatible = "arm,pl011", "arm,primecell";
+			reg = <0x12000 0x1000>;
+			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&uart_clk>, <&uart_clk>;
+			clock-names = "uartclk", "apb_pclk";
+			status = "disabled";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/bcm6846.dtsi b/arch/arm/boot/dts/bcm6846.dtsi
new file mode 100644
index 000000000000..8aa47a2583b2
--- /dev/null
+++ b/arch/arm/boot/dts/bcm6846.dtsi
@@ -0,0 +1,103 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2022 Broadcom Ltd.
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	compatible = "brcm,bcm6846", "brcm,bcmbca";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	interrupt-parent = <&gic>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		CA7_0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x0>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		CA7_1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x1>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		L2_0: l2-cache0 {
+			compatible = "cache";
+		};
+	};
+
+	timer {
+		compatible = "arm,armv7-timer";
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>;
+		arm,cpu-registers-not-fw-configured;
+	};
+
+	pmu: pmu {
+		compatible = "arm,cortex-a7-pmu";
+		interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&CA7_0>, <&CA7_1>;
+	};
+
+	clocks: clocks {
+		periph_clk: periph-clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <200000000>;
+		};
+	};
+
+	psci {
+		compatible = "arm,psci-0.2";
+		method = "smc";
+	};
+
+	axi@81000000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0x81000000 0x8000>;
+
+		gic: interrupt-controller@1000 {
+			compatible = "arm,cortex-a7-gic";
+			#interrupt-cells = <3>;
+			interrupt-controller;
+			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_HIGH)>;
+			reg = <0x1000 0x1000>,
+				<0x2000 0x2000>,
+				<0x4000 0x2000>,
+				<0x6000 0x2000>;
+		};
+	};
+
+	bus@ff800000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0xff800000 0x800000>;
+
+		uart0: serial@640 {
+			compatible = "brcm,bcm6345-uart";
+			reg = <0x640 0x1b>;
+			interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&periph_clk>;
+			clock-names = "refclk";
+			status = "disabled";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/bcm6855.dtsi b/arch/arm/boot/dts/bcm6855.dtsi
new file mode 100644
index 000000000000..620f51aee1a2
--- /dev/null
+++ b/arch/arm/boot/dts/bcm6855.dtsi
@@ -0,0 +1,120 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2022 Broadcom Ltd.
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	compatible = "brcm,bcm6855", "brcm,bcmbca";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	interrupt-parent = <&gic>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		CA7_0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x0>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		CA7_1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x1>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		CA7_2: cpu@2 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x2>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		L2_0: l2-cache0 {
+			compatible = "cache";
+		};
+	};
+
+	timer {
+		compatible = "arm,armv7-timer";
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(3) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(3) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(3) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(3) | IRQ_TYPE_LEVEL_LOW)>;
+		arm,cpu-registers-not-fw-configured;
+	};
+
+	pmu: pmu {
+		compatible = "arm,cortex-a7-pmu";
+		interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&CA7_0>, <&CA7_1>, <&CA7_2>;
+	};
+
+	clocks: clocks {
+		periph_clk: periph-clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <200000000>;
+		};
+
+		uart_clk: uart-clk {
+			compatible = "fixed-factor-clock";
+			#clock-cells = <0>;
+			clocks = <&periph_clk>;
+			clock-div = <4>;
+			clock-mult = <1>;
+		};
+	};
+
+	psci {
+		compatible = "arm,psci-0.2";
+		method = "smc";
+	};
+
+	axi@81000000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0x81000000 0x8000>;
+
+		gic: interrupt-controller@1000 {
+			compatible = "arm,cortex-a7-gic";
+			#interrupt-cells = <3>;
+			interrupt-controller;
+			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(3) | IRQ_TYPE_LEVEL_HIGH)>;
+			reg = <0x1000 0x1000>,
+				<0x2000 0x2000>,
+				<0x4000 0x2000>,
+				<0x6000 0x2000>;
+		};
+	};
+
+	bus@ff800000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0xff800000 0x800000>;
+
+		uart0: serial@12000 {
+			compatible = "arm,pl011", "arm,primecell";
+			reg = <0x12000 0x1000>;
+			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&uart_clk>, <&uart_clk>;
+			clock-names = "uartclk", "apb_pclk";
+			status = "disabled";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/bcm6878.dtsi b/arch/arm/boot/dts/bcm6878.dtsi
new file mode 100644
index 000000000000..1e8b5fa96c25
--- /dev/null
+++ b/arch/arm/boot/dts/bcm6878.dtsi
@@ -0,0 +1,111 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2022 Broadcom Ltd.
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	compatible = "brcm,bcm6878", "brcm,bcmbca";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	interrupt-parent = <&gic>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		CA7_0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x0>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		CA7_1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x1>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		L2_0: l2-cache0 {
+			compatible = "cache";
+		};
+	};
+
+	timer {
+		compatible = "arm,armv7-timer";
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>;
+		arm,cpu-registers-not-fw-configured;
+	};
+
+	pmu: pmu {
+		compatible = "arm,cortex-a7-pmu";
+		interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&CA7_0>, <&CA7_1>;
+	};
+
+	clocks: clocks {
+		periph_clk: periph-clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <200000000>;
+		};
+		uart_clk: uart-clk {
+			compatible = "fixed-factor-clock";
+			#clock-cells = <0>;
+			clocks = <&periph_clk>;
+			clock-div = <4>;
+			clock-mult = <1>;
+		};
+	};
+
+	psci {
+		compatible = "arm,psci-0.2";
+		method = "smc";
+	};
+
+	axi@81000000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0x81000000 0x8000>;
+
+		gic: interrupt-controller@1000 {
+			compatible = "arm,cortex-a7-gic";
+			#interrupt-cells = <3>;
+			interrupt-controller;
+			reg = <0x1000 0x1000>,
+				<0x2000 0x2000>,
+				<0x4000 0x2000>,
+				<0x6000 0x2000>;
+			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(2) |
+					IRQ_TYPE_LEVEL_HIGH)>;
+		};
+	};
+
+	bus@ff800000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0xff800000 0x800000>;
+
+		uart0: serial@12000 {
+			compatible = "arm,pl011", "arm,primecell";
+			reg = <0x12000 0x1000>;
+			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&uart_clk>, <&uart_clk>;
+			clock-names = "uartclk", "apb_pclk";
+			status = "disabled";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/bcm911360_entphn.dts b/arch/arm/boot/dts/bcm911360_entphn.dts
index a76c74b44bba..363009e747b3 100644
--- a/arch/arm/boot/dts/bcm911360_entphn.dts
+++ b/arch/arm/boot/dts/bcm911360_entphn.dts
@@ -47,10 +47,10 @@
 		stdout-path = "serial0:115200n8";
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
-		hook {
+		button-hook {
 			label = "HOOK";
 			linux,code = <KEY_O>;
 			gpios = <&gpio_asiu 48 0>;
diff --git a/arch/arm/boot/dts/bcm947189acdbmr.dts b/arch/arm/boot/dts/bcm947189acdbmr.dts
index b0b8c774a37f..16e70a264faf 100644
--- a/arch/arm/boot/dts/bcm947189acdbmr.dts
+++ b/arch/arm/boot/dts/bcm947189acdbmr.dts
@@ -44,13 +44,13 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 7 GPIO_ACTIVE_HIGH>;
 		};
 
-		wps {
+		button-wps {
 			label = "WPS";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&chipcommon 9 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/bcm947622.dts b/arch/arm/boot/dts/bcm947622.dts
new file mode 100644
index 000000000000..6f083724ab8e
--- /dev/null
+++ b/arch/arm/boot/dts/bcm947622.dts
@@ -0,0 +1,30 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2019 Broadcom Ltd.
+ */
+
+/dts-v1/;
+
+#include "bcm47622.dtsi"
+
+/ {
+	model = "Broadcom BCM947622 Reference Board";
+	compatible = "brcm,bcm947622", "brcm,bcm47622", "brcm,bcmbca";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x08000000>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/bcm953012er.dts b/arch/arm/boot/dts/bcm953012er.dts
index 52feca0fb906..4fe3b3653376 100644
--- a/arch/arm/boot/dts/bcm953012er.dts
+++ b/arch/arm/boot/dts/bcm953012er.dts
@@ -37,7 +37,7 @@
 
 / {
 	model = "NorthStar Enterprise Router (BCM953012ER)";
-	compatible = "brcm,bcm953012er", "brcm,brcm53012", "brcm,bcm4708";
+	compatible = "brcm,bcm953012er", "brcm,bcm53012", "brcm,bcm4708";
 
 	memory@0 {
 		device_type = "memory";
@@ -47,13 +47,13 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		wps {
+		button-wps {
 			label = "WPS";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&chipcommon 6 GPIO_ACTIVE_LOW>;
 		};
 
-		restart {
+		button-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&chipcommon 15 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/bcm953012hr.dts b/arch/arm/boot/dts/bcm953012hr.dts
index 9140be7ec053..b070b69466bd 100644
--- a/arch/arm/boot/dts/bcm953012hr.dts
+++ b/arch/arm/boot/dts/bcm953012hr.dts
@@ -37,7 +37,7 @@
 
 / {
 	model = "NorthStar HR (BCM953012HR)";
-	compatible = "brcm,bcm953012hr", "brcm,brcm53012", "brcm,bcm4708";
+	compatible = "brcm,bcm953012hr", "brcm,bcm53012", "brcm,bcm4708";
 
 	aliases {
 		ethernet0 = &gmac0;
diff --git a/arch/arm/boot/dts/bcm953012k.dts b/arch/arm/boot/dts/bcm953012k.dts
index de40bd59a5fa..f1e6bcaa1edd 100644
--- a/arch/arm/boot/dts/bcm953012k.dts
+++ b/arch/arm/boot/dts/bcm953012k.dts
@@ -36,7 +36,7 @@
 
 / {
 	model = "NorthStar SVK (BCM953012K)";
-	compatible = "brcm,bcm953012k", "brcm,brcm53012", "brcm,bcm4708";
+	compatible = "brcm,bcm953012k", "brcm,bcm53012", "brcm,bcm4708";
 
 	aliases {
 		serial0 = &uart0;
diff --git a/arch/arm/boot/dts/bcm958522er.dts b/arch/arm/boot/dts/bcm958522er.dts
index 60376b62cd5f..15f023656df0 100644
--- a/arch/arm/boot/dts/bcm958522er.dts
+++ b/arch/arm/boot/dts/bcm958522er.dts
@@ -136,7 +136,7 @@
 &qspi {
 	status = "okay";
 	bspi-sel = <0>;
-	flash: m25p80@0 {
+	flash: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "m25p80";
diff --git a/arch/arm/boot/dts/bcm958525er.dts b/arch/arm/boot/dts/bcm958525er.dts
index 8eeb319f5b54..9b9c225a1fb3 100644
--- a/arch/arm/boot/dts/bcm958525er.dts
+++ b/arch/arm/boot/dts/bcm958525er.dts
@@ -136,7 +136,7 @@
 &qspi {
 	status = "okay";
 	bspi-sel = <0>;
-	flash: m25p80@0 {
+	flash: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "m25p80";
diff --git a/arch/arm/boot/dts/bcm958525xmc.dts b/arch/arm/boot/dts/bcm958525xmc.dts
index dc86d5a91292..ca9311452739 100644
--- a/arch/arm/boot/dts/bcm958525xmc.dts
+++ b/arch/arm/boot/dts/bcm958525xmc.dts
@@ -152,7 +152,7 @@
 &qspi {
 	status = "okay";
 	bspi-sel = <0>;
-	flash: m25p80@0 {
+	flash: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "m25p80";
diff --git a/arch/arm/boot/dts/bcm958622hr.dts b/arch/arm/boot/dts/bcm958622hr.dts
index c457e53d886e..9db3c851451a 100644
--- a/arch/arm/boot/dts/bcm958622hr.dts
+++ b/arch/arm/boot/dts/bcm958622hr.dts
@@ -140,7 +140,7 @@
 &qspi {
 	status = "okay";
 	bspi-sel = <0>;
-	flash: m25p80@0 {
+	flash: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "m25p80";
diff --git a/arch/arm/boot/dts/bcm958623hr.dts b/arch/arm/boot/dts/bcm958623hr.dts
index c06871915a1c..32786e7c4e12 100644
--- a/arch/arm/boot/dts/bcm958623hr.dts
+++ b/arch/arm/boot/dts/bcm958623hr.dts
@@ -144,7 +144,7 @@
 &qspi {
 	status = "okay";
 	bspi-sel = <0>;
-	flash: m25p80@0 {
+	flash: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "m25p80";
diff --git a/arch/arm/boot/dts/bcm958625-meraki-alamo.dtsi b/arch/arm/boot/dts/bcm958625-meraki-alamo.dtsi
index 102acd85fab2..c54451dde6dd 100644
--- a/arch/arm/boot/dts/bcm958625-meraki-alamo.dtsi
+++ b/arch/arm/boot/dts/bcm958625-meraki-alamo.dtsi
@@ -13,7 +13,7 @@
 		autorepeat;
 		poll-interval = <20>;
 
-		reset {
+		button-reset {
 			label = "reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&gpioa 8 GPIO_ACTIVE_LOW>;
@@ -57,10 +57,9 @@
 
 		led-4 {
 			/* amber:power */
-			function = LED_FUNCTION_POWER;
+			function = LED_FUNCTION_FAULT;
 			color = <LED_COLOR_ID_AMBER>;
 			gpios = <&gpioa 3 GPIO_ACTIVE_HIGH>;
-			default-state = "on";
 		};
 
 		led-5 {
@@ -118,6 +117,8 @@
 						reg = <0>;
 						ethernet = <&sgmii1>;
 						phy-mode = "sgmii";
+						qca,sgmii-enable-pll;
+						qca,sgmii-txclk-falling-edge;
 						fixed-link {
 							speed = <1000>;
 							full-duplex;
@@ -194,6 +195,8 @@
 						reg = <0>;
 						ethernet = <&sgmii0>;
 						phy-mode = "sgmii";
+						qca,sgmii-enable-pll;
+						qca,sgmii-txclk-falling-edge;
 						fixed-link {
 							speed = <1000>;
 							full-duplex;
diff --git a/arch/arm/boot/dts/bcm958625-meraki-kingpin.dtsi b/arch/arm/boot/dts/bcm958625-meraki-kingpin.dtsi
index 7c487c74fd10..1830844c8404 100644
--- a/arch/arm/boot/dts/bcm958625-meraki-kingpin.dtsi
+++ b/arch/arm/boot/dts/bcm958625-meraki-kingpin.dtsi
@@ -14,7 +14,7 @@
 		autorepeat;
 		poll-interval = <20>;
 
-		reset {
+		button-reset {
 			label = "reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&gpioa 6 GPIO_ACTIVE_LOW>;
@@ -106,10 +106,9 @@
 
 		led-a {
 			/* amber:power */
-			function = LED_FUNCTION_POWER;
+			function = LED_FUNCTION_FAULT;
 			color = <LED_COLOR_ID_AMBER>;
 			gpios = <&gpioa 0 GPIO_ACTIVE_LOW>;
-			default-state = "on";
 		};
 
 		led-b {
diff --git a/arch/arm/boot/dts/bcm958625-meraki-mx6x-common.dtsi b/arch/arm/boot/dts/bcm958625-meraki-mx6x-common.dtsi
index 6519b7c61af1..b0854d881ac6 100644
--- a/arch/arm/boot/dts/bcm958625-meraki-mx6x-common.dtsi
+++ b/arch/arm/boot/dts/bcm958625-meraki-mx6x-common.dtsi
@@ -22,7 +22,7 @@
 		};
 
 		led-2 {
-			function = LED_FUNCTION_INDICATOR;
+			function = LED_FUNCTION_POWER;
 			color = <LED_COLOR_ID_GREEN>;
 			pwms = <&pwm 2 50000>;
 			max-brightness = <255>;
@@ -39,6 +39,8 @@
 
 &amac2 {
 	status = "okay";
+	nvmem-cells = <&mac_address>;
+	nvmem-cell-names = "mac-address";
 };
 
 &ehci0 {
@@ -53,6 +55,12 @@
 		reg = <0x50>;
 		pagesize = <32>;
 		read-only;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		mac_address: mac-address@66 {
+			reg = <0x66 0x6>;
+		};
 	};
 };
 
diff --git a/arch/arm/boot/dts/bcm958625hr.dts b/arch/arm/boot/dts/bcm958625hr.dts
index b22fc6624ae4..74263d98de73 100644
--- a/arch/arm/boot/dts/bcm958625hr.dts
+++ b/arch/arm/boot/dts/bcm958625hr.dts
@@ -151,7 +151,7 @@
 &qspi {
 	status = "okay";
 	bspi-sel = <0>;
-	flash: m25p80@0 {
+	flash: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "m25p80";
diff --git a/arch/arm/boot/dts/bcm958625k.dts b/arch/arm/boot/dts/bcm958625k.dts
index 0183f8965a74..69ebc7a913a7 100644
--- a/arch/arm/boot/dts/bcm958625k.dts
+++ b/arch/arm/boot/dts/bcm958625k.dts
@@ -155,7 +155,7 @@
 &qspi {
 	status = "okay";
 	bspi-sel = <0>;
-	flash: m25p80@0 {
+	flash: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "m25p80";
diff --git a/arch/arm/boot/dts/bcm963138.dts b/arch/arm/boot/dts/bcm963138.dts
new file mode 100644
index 000000000000..d28c4f130ca2
--- /dev/null
+++ b/arch/arm/boot/dts/bcm963138.dts
@@ -0,0 +1,27 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2022 Broadcom Ltd.
+ */
+
+/dts-v1/;
+
+#include "bcm63138.dtsi"
+
+/ {
+	model = "Broadcom BCM963138 Reference Board";
+	compatible = "brcm,bcm963138", "brcm,bcm63138", "brcm,bcmbca";
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+		stdout-path = &serial0;
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x08000000>;
+	};
+};
+
+&serial0 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/bcm963138dvt.dts b/arch/arm/boot/dts/bcm963138dvt.dts
index df5c8ab90627..15bec75be74c 100644
--- a/arch/arm/boot/dts/bcm963138dvt.dts
+++ b/arch/arm/boot/dts/bcm963138dvt.dts
@@ -8,7 +8,7 @@
 #include "bcm63138.dtsi"
 
 / {
-	compatible = "brcm,BCM963138DVT", "brcm,bcm63138";
+	compatible = "brcm,BCM963138DVT", "brcm,bcm63138", "brcm,bcmbca";
 	model = "Broadcom BCM963138DVT";
 
 	chosen {
diff --git a/arch/arm/boot/dts/bcm963148.dts b/arch/arm/boot/dts/bcm963148.dts
new file mode 100644
index 000000000000..98f6a6d09f50
--- /dev/null
+++ b/arch/arm/boot/dts/bcm963148.dts
@@ -0,0 +1,30 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2019 Broadcom Ltd.
+ */
+
+/dts-v1/;
+
+#include "bcm63148.dtsi"
+
+/ {
+	model = "Broadcom BCM963148 Reference Board";
+	compatible = "brcm,bcm963148", "brcm,bcm63148", "brcm,bcmbca";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x08000000>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/bcm963178.dts b/arch/arm/boot/dts/bcm963178.dts
new file mode 100644
index 000000000000..fa096e9cde23
--- /dev/null
+++ b/arch/arm/boot/dts/bcm963178.dts
@@ -0,0 +1,30 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2019 Broadcom Ltd.
+ */
+
+/dts-v1/;
+
+#include "bcm63178.dtsi"
+
+/ {
+	model = "Broadcom BCM963178 Reference Board";
+	compatible = "brcm,bcm963178", "brcm,bcm63178", "brcm,bcmbca";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x08000000>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/bcm96756.dts b/arch/arm/boot/dts/bcm96756.dts
new file mode 100644
index 000000000000..9a4a87ba9c8a
--- /dev/null
+++ b/arch/arm/boot/dts/bcm96756.dts
@@ -0,0 +1,30 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2019 Broadcom Ltd.
+ */
+
+/dts-v1/;
+
+#include "bcm6756.dtsi"
+
+/ {
+	model = "Broadcom BCM96756 Reference Board";
+	compatible = "brcm,bcm96756", "brcm,bcm6756", "brcm,bcmbca";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x08000000>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/bcm96846.dts b/arch/arm/boot/dts/bcm96846.dts
new file mode 100644
index 000000000000..c70ebccabc19
--- /dev/null
+++ b/arch/arm/boot/dts/bcm96846.dts
@@ -0,0 +1,30 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2022 Broadcom Ltd.
+ */
+
+/dts-v1/;
+
+#include "bcm6846.dtsi"
+
+/ {
+	model = "Broadcom BCM96846 Reference Board";
+	compatible = "brcm,bcm96846", "brcm,bcm6846", "brcm,bcmbca";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x08000000>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/bcm96855.dts b/arch/arm/boot/dts/bcm96855.dts
new file mode 100644
index 000000000000..4438152561ac
--- /dev/null
+++ b/arch/arm/boot/dts/bcm96855.dts
@@ -0,0 +1,30 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2019 Broadcom Ltd.
+ */
+
+/dts-v1/;
+
+#include "bcm6855.dtsi"
+
+/ {
+	model = "Broadcom BCM96855 Reference Board";
+	compatible = "brcm,bcm96855", "brcm,bcm6855", "brcm,bcmbca";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x08000000>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/bcm96878.dts b/arch/arm/boot/dts/bcm96878.dts
new file mode 100644
index 000000000000..8fbc175cb452
--- /dev/null
+++ b/arch/arm/boot/dts/bcm96878.dts
@@ -0,0 +1,30 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2019 Broadcom Ltd.
+ */
+
+/dts-v1/;
+
+#include "bcm6878.dtsi"
+
+/ {
+	model = "Broadcom BCM96878 Reference Board";
+	compatible = "brcm,bcm96878", "brcm,bcm6878", "brcm,bcmbca";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x08000000>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/bcm988312hr.dts b/arch/arm/boot/dts/bcm988312hr.dts
index 007e34715956..e96bc3f2d5cf 100644
--- a/arch/arm/boot/dts/bcm988312hr.dts
+++ b/arch/arm/boot/dts/bcm988312hr.dts
@@ -140,7 +140,7 @@
 &qspi {
 	status = "okay";
 	bspi-sel = <0>;
-	flash: m25p80@0 {
+	flash: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "m25p80";
diff --git a/arch/arm/boot/dts/da850-evm.dts b/arch/arm/boot/dts/da850-evm.dts
index 87c517d65f62..1fdd9a249165 100644
--- a/arch/arm/boot/dts/da850-evm.dts
+++ b/arch/arm/boot/dts/da850-evm.dts
@@ -52,15 +52,15 @@
 		enable-gpios = <&gpio 40 GPIO_ACTIVE_HIGH>; /* lcd_panel_pwr */
 
 		panel-info {
-			ac-bias		= <255>;
-			ac-bias-intrpt	= <0>;
-			dma-burst-sz	= <16>;
-			bpp		= <16>;
-			fdd		= <0x80>;
-			sync-edge	= <0>;
-			sync-ctrl	= <1>;
-			raster-order	= <0>;
-			fifo-th		= <0>;
+			ac-bias = <255>;
+			ac-bias-intrpt = <0>;
+			dma-burst-sz = <16>;
+			bpp = <16>;
+			fdd = <0x80>;
+			sync-edge = <0>;
+			sync-ctrl = <1>;
+			raster-order = <0>;
+			fifo-th = <0>;
 		};
 
 		display-timings {
@@ -278,7 +278,7 @@
 	status = "okay";
 	pinctrl-names = "default";
 	pinctrl-0 = <&spi1_pins &spi1_cs0_pin>;
-	flash: m25p80@0 {
+	flash: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "jedec,spi-nor";
diff --git a/arch/arm/boot/dts/da850.dtsi b/arch/arm/boot/dts/da850.dtsi
index c3942b4e82ad..e46e4d22db39 100644
--- a/arch/arm/boot/dts/da850.dtsi
+++ b/arch/arm/boot/dts/da850.dtsi
@@ -419,7 +419,7 @@
 		edma0: edma@0 {
 			compatible = "ti,edma3-tpcc";
 			/* eDMA3 CC0: 0x01c0 0000 - 0x01c0 7fff */
-			reg =	<0x0 0x8000>;
+			reg = <0x0 0x8000>;
 			reg-names = "edma3_cc";
 			interrupts = <11 12>;
 			interrupt-names = "edma3_ccint", "edma3_ccerrint";
@@ -430,14 +430,14 @@
 		};
 		edma0_tptc0: tptc@8000 {
 			compatible = "ti,edma3-tptc";
-			reg =	<0x8000 0x400>;
+			reg = <0x8000 0x400>;
 			interrupts = <13>;
 			interrupt-names = "edm3_tcerrint";
 			power-domains = <&psc0 1>;
 		};
 		edma0_tptc1: tptc@8400 {
 			compatible = "ti,edma3-tptc";
-			reg =	<0x8400 0x400>;
+			reg = <0x8400 0x400>;
 			interrupts = <32>;
 			interrupt-names = "edm3_tcerrint";
 			power-domains = <&psc0 2>;
@@ -445,7 +445,7 @@
 		edma1: edma@230000 {
 			compatible = "ti,edma3-tpcc";
 			/* eDMA3 CC1: 0x01e3 0000 - 0x01e3 7fff */
-			reg =	<0x230000 0x8000>;
+			reg = <0x230000 0x8000>;
 			reg-names = "edma3_cc";
 			interrupts = <93 94>;
 			interrupt-names = "edma3_ccint", "edma3_ccerrint";
@@ -456,7 +456,7 @@
 		};
 		edma1_tptc0: tptc@238000 {
 			compatible = "ti,edma3-tptc";
-			reg =	<0x238000 0x400>;
+			reg = <0x238000 0x400>;
 			interrupts = <95>;
 			interrupt-names = "edm3_tcerrint";
 			power-domains = <&psc1 21>;
@@ -672,14 +672,16 @@
 
 			cppi41dma: dma-controller@201000 {
 				compatible = "ti,da830-cppi41";
-				reg =  <0x201000 0x1000
+				reg = <0x201000 0x1000
 					0x202000 0x1000
 					0x204000 0x4000>;
 				reg-names = "controller",
 					    "scheduler", "queuemgr";
 				interrupts = <58>;
 				#dma-cells = <2>;
+				/* For backwards compatibility: */
 				#dma-channels = <4>;
+				dma-channels = <4>;
 				power-domains = <&psc1 1>;
 				status = "okay";
 			};
diff --git a/arch/arm/boot/dts/dm8148-evm.dts b/arch/arm/boot/dts/dm8148-evm.dts
index 8ef48c00f98d..fe3f9a970b18 100644
--- a/arch/arm/boot/dts/dm8148-evm.dts
+++ b/arch/arm/boot/dts/dm8148-evm.dts
@@ -51,7 +51,7 @@
 		interrupt-parent = <&gpmc>;
 		interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
 			     <1 IRQ_TYPE_NONE>; /* termcount */
-		linux,mtd-name= "micron,mt29f2g16aadwp";
+		linux,mtd-name = "micron,mt29f2g16aadwp";
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ti,nand-ecc-opt = "bch8";
diff --git a/arch/arm/boot/dts/dm814x.dtsi b/arch/arm/boot/dts/dm814x.dtsi
index 7702e048e110..8104969c67c1 100644
--- a/arch/arm/boot/dts/dm814x.dtsi
+++ b/arch/arm/boot/dts/dm814x.dtsi
@@ -1,8 +1,4 @@
-/*
- * This file is licensed under the terms of the GNU General Public License
- * version 2.  This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
- */
+// SPDX-License-Identifier: GPL-2.0-only
 
 #include <dt-bindings/bus/ti-sysc.h>
 #include <dt-bindings/clock/dm814.h>
@@ -167,8 +163,11 @@
 				interrupts = <17>;
 				interrupt-names = "glue";
 				#dma-cells = <2>;
+				/* For backwards compatibility: */
 				#dma-channels = <30>;
+				dma-channels = <30>;
 				#dma-requests = <256>;
+				dma-requests = <256>;
 			};
 		};
 
diff --git a/arch/arm/boot/dts/dm8168-evm.dts b/arch/arm/boot/dts/dm8168-evm.dts
index 5126e2d72ed7..244a957f9ba3 100644
--- a/arch/arm/boot/dts/dm8168-evm.dts
+++ b/arch/arm/boot/dts/dm8168-evm.dts
@@ -119,7 +119,7 @@
 
 	nand@0,0 {
 		compatible = "ti,omap2-nand";
-		linux,mtd-name= "micron,mt29f2g16aadwp";
+		linux,mtd-name = "micron,mt29f2g16aadwp";
 		reg = <0 0 4>; /* CS0, offset 0, IO size 4 */
 		interrupt-parent = <&gpmc>;
 		interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
@@ -177,7 +177,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&mcspi1_pins>;
 
-	m25p80@0 {
+	flash@0 {
 		compatible = "w25x32";
 		spi-max-frequency = <48000000>;
 		reg = <0>;
diff --git a/arch/arm/boot/dts/dm816x.dtsi b/arch/arm/boot/dts/dm816x.dtsi
index a9e7274806f4..649b33194455 100644
--- a/arch/arm/boot/dts/dm816x.dtsi
+++ b/arch/arm/boot/dts/dm816x.dtsi
@@ -1,8 +1,4 @@
-/*
- * This file is licensed under the terms of the GNU General Public License
- * version 2.  This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
- */
+// SPDX-License-Identifier: GPL-2.0-only
 
 #include <dt-bindings/bus/ti-sysc.h>
 #include <dt-bindings/clock/dm816.h>
@@ -655,8 +651,11 @@
 				interrupts = <17>;
 				interrupt-names = "glue";
 				#dma-cells = <2>;
+				/* For backwards compatibility: */
 				#dma-channels = <30>;
+				dma-channels = <30>;
 				#dma-requests = <256>;
+				dma-requests = <256>;
 			};
 		};
 
diff --git a/arch/arm/boot/dts/dove-cubox.dts b/arch/arm/boot/dts/dove-cubox.dts
index 3e1584e787ae..2639b9fe0ab4 100644
--- a/arch/arm/boot/dts/dove-cubox.dts
+++ b/arch/arm/boot/dts/dove-cubox.dts
@@ -127,7 +127,7 @@
 	status = "okay";
 
 	/* spi0.0: 4M Flash Winbond W25Q32BV */
-	spi-flash@0 {
+	flash@0 {
 		compatible = "st,w25q32";
 		spi-max-frequency = <20000000>;
 		reg = <0>;
diff --git a/arch/arm/boot/dts/dove-d2plug.dts b/arch/arm/boot/dts/dove-d2plug.dts
index 273f12ca2512..a0e8996c2ffd 100644
--- a/arch/arm/boot/dts/dove-d2plug.dts
+++ b/arch/arm/boot/dts/dove-d2plug.dts
@@ -62,7 +62,7 @@
 	status = "okay";
 
 	/* spi0.0: 4M Flash Macronix MX25L3205D */
-	spi-flash@0 {
+	flash@0 {
 		compatible = "st,m25l3205d";
 		spi-max-frequency = <20000000>;
 		reg = <0>;
diff --git a/arch/arm/boot/dts/dove-d3plug.dts b/arch/arm/boot/dts/dove-d3plug.dts
index 826026c28f90..1e81d1b97055 100644
--- a/arch/arm/boot/dts/dove-d3plug.dts
+++ b/arch/arm/boot/dts/dove-d3plug.dts
@@ -79,7 +79,7 @@
 	status = "okay";
 
 	/* spi0.0: 2M Flash Macronix MX25L1605D */
-	spi-flash@0 {
+	flash@0 {
 		compatible = "st,m25l1605d";
 		spi-max-frequency = <86000000>;
 		reg = <0>;
diff --git a/arch/arm/boot/dts/dove-dove-db.dts b/arch/arm/boot/dts/dove-dove-db.dts
index 1754a62e014e..c1912dc6bfc3 100644
--- a/arch/arm/boot/dts/dove-dove-db.dts
+++ b/arch/arm/boot/dts/dove-dove-db.dts
@@ -27,7 +27,7 @@
 	status = "okay";
 
 	/* spi0.0: 4M Flash ST-M25P32-VMF6P */
-	spi-flash@0 {
+	flash@0 {
 		compatible = "st,m25p32";
 		spi-max-frequency = <20000000>;
 		reg = <0>;
diff --git a/arch/arm/boot/dts/dove.dtsi b/arch/arm/boot/dts/dove.dtsi
index 89e0bdaf3a85..00a36fba2fd2 100644
--- a/arch/arm/boot/dts/dove.dtsi
+++ b/arch/arm/boot/dts/dove.dtsi
@@ -122,8 +122,18 @@
 				bus-range = <0x00 0xff>;
 
 				#interrupt-cells = <1>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &intc 16>;
+				interrupt-names = "intx", "error";
+				interrupts = <16>, <15>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie0_intc 0>,
+						<0 0 0 2 &pcie0_intc 1>,
+						<0 0 0 3 &pcie0_intc 2>,
+						<0 0 0 4 &pcie0_intc 3>;
+
+				pcie0_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			pcie1: pcie@2 {
@@ -141,8 +151,18 @@
 				bus-range = <0x00 0xff>;
 
 				#interrupt-cells = <1>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &intc 18>;
+				interrupt-names = "intx", "error";
+				interrupts = <18>, <17>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie1_intc 0>,
+						<0 0 0 2 &pcie1_intc 1>,
+						<0 0 0 3 &pcie1_intc 2>,
+						<0 0 0 4 &pcie1_intc 3>;
+
+				pcie1_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 		};
 
diff --git a/arch/arm/boot/dts/dra62x-j5eco-evm.dts b/arch/arm/boot/dts/dra62x-j5eco-evm.dts
index c16e183822be..577114c4c20a 100644
--- a/arch/arm/boot/dts/dra62x-j5eco-evm.dts
+++ b/arch/arm/boot/dts/dra62x-j5eco-evm.dts
@@ -51,7 +51,7 @@
 		interrupt-parent = <&gpmc>;
 		interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
 			     <1 IRQ_TYPE_NONE>; /* termcount */
-		linux,mtd-name= "micron,mt29f2g16aadwp";
+		linux,mtd-name = "micron,mt29f2g16aadwp";
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ti,nand-ecc-opt = "bch8";
diff --git a/arch/arm/boot/dts/dra62x.dtsi b/arch/arm/boot/dts/dra62x.dtsi
index cc4878aaa8ea..cfefa670515c 100644
--- a/arch/arm/boot/dts/dra62x.dtsi
+++ b/arch/arm/boot/dts/dra62x.dtsi
@@ -1,8 +1,4 @@
-/*
- * This file is licensed under the terms of the GNU General Public License
- * version 2.  This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
- */
+// SPDX-License-Identifier: GPL-2.0-only
 
 #include "dm814x.dtsi"
 
diff --git a/arch/arm/boot/dts/dra7-dspeve-thermal.dtsi b/arch/arm/boot/dts/dra7-dspeve-thermal.dtsi
index e75569383dd8..747ff0db90c7 100644
--- a/arch/arm/boot/dts/dra7-dspeve-thermal.dtsi
+++ b/arch/arm/boot/dts/dra7-dspeve-thermal.dtsi
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Device Tree Source for DRA7x SoC DSPEVE thermal
  *
  * Copyright (C) 2016 Texas Instruments Incorporated - https://www.ti.com/
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2.  This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
  */
 
 #include <dt-bindings/thermal/thermal.h>
diff --git a/arch/arm/boot/dts/dra7-evm-common.dtsi b/arch/arm/boot/dts/dra7-evm-common.dtsi
index 0f71a9f37a72..68c43eb12c1a 100644
--- a/arch/arm/boot/dts/dra7-evm-common.dtsi
+++ b/arch/arm/boot/dts/dra7-evm-common.dtsi
@@ -135,7 +135,7 @@
 	status = "okay";
 
 	spi-max-frequency = <76800000>;
-	m25p80@0 {
+	flash@0 {
 		compatible = "s25fl256s1";
 		spi-max-frequency = <76800000>;
 		reg = <0>;
diff --git a/arch/arm/boot/dts/dra7-iva-thermal.dtsi b/arch/arm/boot/dts/dra7-iva-thermal.dtsi
index a7077321613f..0a31313065df 100644
--- a/arch/arm/boot/dts/dra7-iva-thermal.dtsi
+++ b/arch/arm/boot/dts/dra7-iva-thermal.dtsi
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Device Tree Source for DRA7x SoC IVA thermal
  *
  * Copyright (C) 2016 Texas Instruments Incorporated - https://www.ti.com/
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2.  This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
  */
 
 #include <dt-bindings/thermal/thermal.h>
diff --git a/arch/arm/boot/dts/dra7-l4.dtsi b/arch/arm/boot/dts/dra7-l4.dtsi
index 956a26d52a4c..5733e3a4ea8e 100644
--- a/arch/arm/boot/dts/dra7-l4.dtsi
+++ b/arch/arm/boot/dts/dra7-l4.dtsi
@@ -3482,8 +3482,7 @@
 				ti,timer-pwm;
 			};
 		};
-
-		target-module@2c000 {			/* 0x4882c000, ap 17 02.0 */
+		timer15_target: target-module@2c000 {	/* 0x4882c000, ap 17 02.0 */
 			compatible = "ti,sysc-omap4-timer", "ti,sysc";
 			reg = <0x2c000 0x4>,
 			      <0x2c010 0x4>;
@@ -3511,7 +3510,7 @@
 			};
 		};
 
-		target-module@2e000 {			/* 0x4882e000, ap 19 14.0 */
+		timer16_target: target-module@2e000 {	/* 0x4882e000, ap 19 14.0 */
 			compatible = "ti,sysc-omap4-timer", "ti,sysc";
 			reg = <0x2e000 0x4>,
 			      <0x2e010 0x4>;
@@ -4189,11 +4188,11 @@
 			reg = <0x1d0010 0x4>;
 			reg-names = "sysc";
 			ti,sysc-midle = <SYSC_IDLE_FORCE>,
-					<SYSC_IDLE_NO>,
-					<SYSC_IDLE_SMART>;
+					<SYSC_IDLE_NO>;
 			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
 					<SYSC_IDLE_NO>,
 					<SYSC_IDLE_SMART>;
+			power-domains = <&prm_vpe>;
 			clocks = <&vpe_clkctrl DRA7_VPE_VPE_CLKCTRL 0>;
 			clock-names = "fck";
 			#address-cells = <1>;
diff --git a/arch/arm/boot/dts/dra7.dtsi b/arch/arm/boot/dts/dra7.dtsi
index 6b485cbed8d5..97ce0c4f1df7 100644
--- a/arch/arm/boot/dts/dra7.dtsi
+++ b/arch/arm/boot/dts/dra7.dtsi
@@ -160,7 +160,7 @@
 		target-module@48210000 {
 			compatible = "ti,sysc-omap4-simple", "ti,sysc";
 			power-domains = <&prm_mpu>;
-			clocks = <&mpu_clkctrl DRA7_MPU_CLKCTRL 0>;
+			clocks = <&mpu_clkctrl DRA7_MPU_MPU_CLKCTRL 0>;
 			clock-names = "fck";
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -875,10 +875,10 @@
 			      <0x58000014 4>;
 			reg-names = "rev", "syss";
 			ti,syss-mask = <1>;
-			clocks = <&dss_clkctrl DRA7_DSS_CORE_CLKCTRL 0>,
-				 <&dss_clkctrl DRA7_DSS_CORE_CLKCTRL 9>,
-				 <&dss_clkctrl DRA7_DSS_CORE_CLKCTRL 10>,
-				 <&dss_clkctrl DRA7_DSS_CORE_CLKCTRL 11>;
+			clocks = <&dss_clkctrl DRA7_DSS_DSS_CORE_CLKCTRL 0>,
+				 <&dss_clkctrl DRA7_DSS_DSS_CORE_CLKCTRL 9>,
+				 <&dss_clkctrl DRA7_DSS_DSS_CORE_CLKCTRL 10>,
+				 <&dss_clkctrl DRA7_DSS_DSS_CORE_CLKCTRL 11>;
 			clock-names = "fck", "hdmi_clk", "sys_clk", "tv_clk";
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -912,7 +912,7 @@
 							 SYSC_OMAP2_SOFTRESET |
 							 SYSC_OMAP2_AUTOIDLE)>;
 					ti,syss-mask = <1>;
-					clocks = <&dss_clkctrl DRA7_DSS_CORE_CLKCTRL 8>;
+					clocks = <&dss_clkctrl DRA7_DSS_DSS_CORE_CLKCTRL 8>;
 					clock-names = "fck";
 					#address-cells = <1>;
 					#size-cells = <1>;
@@ -939,8 +939,8 @@
 							<SYSC_IDLE_SMART>,
 							<SYSC_IDLE_SMART_WKUP>;
 					ti,sysc-mask = <(SYSC_OMAP4_SOFTRESET)>;
-					clocks = <&dss_clkctrl DRA7_DSS_CORE_CLKCTRL 9>,
-						 <&dss_clkctrl DRA7_DSS_CORE_CLKCTRL 8>;
+					clocks = <&dss_clkctrl DRA7_DSS_DSS_CORE_CLKCTRL 9>,
+						 <&dss_clkctrl DRA7_DSS_DSS_CORE_CLKCTRL 8>;
 					clock-names = "fck", "dss_clk";
 					#address-cells = <1>;
 					#size-cells = <1>;
@@ -979,7 +979,7 @@
 				compatible = "vivante,gc";
 				reg = <0x0 0x700>;
 				interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
-				clocks = <&dss_clkctrl DRA7_BB2D_CLKCTRL 0>;
+				clocks = <&dss_clkctrl DRA7_DSS_BB2D_CLKCTRL 0>;
 				clock-names = "core";
 			};
 		};
@@ -1333,26 +1333,26 @@
 	ti,no-reset-on-init;
 	ti,no-idle;
 	timer@0 {
-		assigned-clocks = <&wkupaon_clkctrl DRA7_TIMER1_CLKCTRL 24>;
+		assigned-clocks = <&wkupaon_clkctrl DRA7_WKUPAON_TIMER1_CLKCTRL 24>;
 		assigned-clock-parents = <&sys_32k_ck>;
 	};
 };
 
 /* Local timers, see ARM architected timer wrap erratum i940 */
-&timer3_target {
+&timer15_target {
 	ti,no-reset-on-init;
 	ti,no-idle;
 	timer@0 {
-		assigned-clocks = <&l4per_clkctrl DRA7_L4PER_TIMER3_CLKCTRL 24>;
+		assigned-clocks = <&l4per3_clkctrl DRA7_L4PER3_TIMER15_CLKCTRL 24>;
 		assigned-clock-parents = <&timer_sys_clk_div>;
 	};
 };
 
-&timer4_target {
+&timer16_target {
 	ti,no-reset-on-init;
 	ti,no-idle;
 	timer@0 {
-		assigned-clocks = <&l4per_clkctrl DRA7_L4PER_TIMER4_CLKCTRL 24>;
+		assigned-clocks = <&l4per3_clkctrl DRA7_L4PER3_TIMER16_CLKCTRL 24>;
 		assigned-clock-parents = <&timer_sys_clk_div>;
 	};
 };
diff --git a/arch/arm/boot/dts/dra72-evm-common.dtsi b/arch/arm/boot/dts/dra72-evm-common.dtsi
index f12825268188..8948e10dbeb8 100644
--- a/arch/arm/boot/dts/dra72-evm-common.dtsi
+++ b/arch/arm/boot/dts/dra72-evm-common.dtsi
@@ -474,7 +474,7 @@
 	status = "okay";
 
 	spi-max-frequency = <76800000>;
-	m25p80@0 {
+	flash@0 {
 		compatible = "s25fl256s1";
 		spi-max-frequency = <76800000>;
 		reg = <0>;
diff --git a/arch/arm/boot/dts/dra72x-mmc-iodelay.dtsi b/arch/arm/boot/dts/dra72x-mmc-iodelay.dtsi
index a9dce919d443..34eea3c048bd 100644
--- a/arch/arm/boot/dts/dra72x-mmc-iodelay.dtsi
+++ b/arch/arm/boot/dts/dra72x-mmc-iodelay.dtsi
@@ -1,16 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * MMC IOdelay values for TI's DRA72x, DRA71x and AM571x SoCs.
  *
  * Copyright (C) 2017 Texas Instruments Incorporated - https://www.ti.com/
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation version 2.
- *
- * This program is distributed "as is" WITHOUT ANY WARRANTY of any
- * kind, whether express or implied; without even the implied warranty
- * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
  */
 
 /*
diff --git a/arch/arm/boot/dts/dra74x-mmc-iodelay.dtsi b/arch/arm/boot/dts/dra74x-mmc-iodelay.dtsi
index e86da7a970b6..b9d040135c5f 100644
--- a/arch/arm/boot/dts/dra74x-mmc-iodelay.dtsi
+++ b/arch/arm/boot/dts/dra74x-mmc-iodelay.dtsi
@@ -1,16 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * MMC IOdelay values for TI's DRA74x, DRA75x and AM572x SoCs.
  *
  * Copyright (C) 2017 Texas Instruments Incorporated - https://www.ti.com/
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation version 2.
- *
- * This program is distributed "as is" WITHOUT ANY WARRANTY of any
- * kind, whether express or implied; without even the implied warranty
- * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
  */
 
 /*
diff --git a/arch/arm/boot/dts/dra76-evm.dts b/arch/arm/boot/dts/dra76-evm.dts
index e2b7fcb061cf..57868ac60d29 100644
--- a/arch/arm/boot/dts/dra76-evm.dts
+++ b/arch/arm/boot/dts/dra76-evm.dts
@@ -511,7 +511,7 @@
 
 &qspi {
 	spi-max-frequency = <96000000>;
-	m25p80@0 {
+	flash@0 {
 		spi-max-frequency = <96000000>;
 	};
 };
diff --git a/arch/arm/boot/dts/dra76x.dtsi b/arch/arm/boot/dts/dra76x.dtsi
index bc4ae91cba16..931db7932c11 100644
--- a/arch/arm/boot/dts/dra76x.dtsi
+++ b/arch/arm/boot/dts/dra76x.dtsi
@@ -90,8 +90,8 @@
 		clocks = <&dpll_gmac_x2_ck>;
 		ti,max-div = <63>;
 		reg = <0x03fc>;
-		ti,bit-shift=<20>;
-		ti,latch-bit=<26>;
+		ti,bit-shift = <20>;
+		ti,latch-bit = <26>;
 		assigned-clocks = <&dpll_gmac_h14x2_ctrl_ck>;
 		assigned-clock-rates = <80000000>;
 	};
@@ -102,7 +102,7 @@
 		clocks = <&dpll_gmac_ck>, <&dpll_gmac_h14x2_ctrl_ck>;
 		reg = <0x3fc>;
 		ti,bit-shift = <29>;
-		ti,latch-bit=<26>;
+		ti,latch-bit = <26>;
 		assigned-clocks = <&dpll_gmac_h14x2_ctrl_mux_ck>;
 		assigned-clock-parents = <&dpll_gmac_h14x2_ctrl_ck>;
 	};
diff --git a/arch/arm/boot/dts/dra7xx-clocks.dtsi b/arch/arm/boot/dts/dra7xx-clocks.dtsi
index 2365554eef3c..04a7a6d1d529 100644
--- a/arch/arm/boot/dts/dra7xx-clocks.dtsi
+++ b/arch/arm/boot/dts/dra7xx-clocks.dtsi
@@ -5,210 +5,244 @@
  * Copyright (C) 2013 Texas Instruments, Inc.
  */
 &cm_core_aon_clocks {
-	atl_clkin0_ck: atl_clkin0_ck {
+	atl_clkin0_ck: clock-atl-clkin0 {
 		#clock-cells = <0>;
 		compatible = "ti,dra7-atl-clock";
+		clock-output-names = "atl_clkin0_ck";
 		clocks = <&atl_clkctrl DRA7_ATL_ATL_CLKCTRL 26>;
 	};
 
-	atl_clkin1_ck: atl_clkin1_ck {
+	atl_clkin1_ck: clock-atl-clkin1 {
 		#clock-cells = <0>;
 		compatible = "ti,dra7-atl-clock";
+		clock-output-names = "atl_clkin1_ck";
 		clocks = <&atl_clkctrl DRA7_ATL_ATL_CLKCTRL 26>;
 	};
 
-	atl_clkin2_ck: atl_clkin2_ck {
+	atl_clkin2_ck: clock-atl-clkin2 {
 		#clock-cells = <0>;
 		compatible = "ti,dra7-atl-clock";
+		clock-output-names = "atl_clkin2_ck";
 		clocks = <&atl_clkctrl DRA7_ATL_ATL_CLKCTRL 26>;
 	};
 
-	atl_clkin3_ck: atl_clkin3_ck {
+	atl_clkin3_ck: clock-atl-clkin3 {
 		#clock-cells = <0>;
 		compatible = "ti,dra7-atl-clock";
+		clock-output-names = "atl_clkin3_ck";
 		clocks = <&atl_clkctrl DRA7_ATL_ATL_CLKCTRL 26>;
 	};
 
-	hdmi_clkin_ck: hdmi_clkin_ck {
+	hdmi_clkin_ck: clock-hdmi-clkin {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "hdmi_clkin_ck";
 		clock-frequency = <0>;
 	};
 
-	mlb_clkin_ck: mlb_clkin_ck {
+	mlb_clkin_ck: clock-mlb-clkin {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "mlb_clkin_ck";
 		clock-frequency = <0>;
 	};
 
-	mlbp_clkin_ck: mlbp_clkin_ck {
+	mlbp_clkin_ck: clock-mlbp-clkin {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "mlbp_clkin_ck";
 		clock-frequency = <0>;
 	};
 
-	pciesref_acs_clk_ck: pciesref_acs_clk_ck {
+	pciesref_acs_clk_ck: clock-pciesref-acs {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "pciesref_acs_clk_ck";
 		clock-frequency = <100000000>;
 	};
 
-	ref_clkin0_ck: ref_clkin0_ck {
+	ref_clkin0_ck: clock-ref-clkin0 {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "ref_clkin0_ck";
 		clock-frequency = <0>;
 	};
 
-	ref_clkin1_ck: ref_clkin1_ck {
+	ref_clkin1_ck: clock-ref-clkin1 {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "ref_clkin1_ck";
 		clock-frequency = <0>;
 	};
 
-	ref_clkin2_ck: ref_clkin2_ck {
+	ref_clkin2_ck: clock-ref-clkin2 {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "ref_clkin2_ck";
 		clock-frequency = <0>;
 	};
 
-	ref_clkin3_ck: ref_clkin3_ck {
+	ref_clkin3_ck: clock-ref-clkin3 {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "ref_clkin3_ck";
 		clock-frequency = <0>;
 	};
 
-	rmii_clk_ck: rmii_clk_ck {
+	rmii_clk_ck: clock-rmii {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "rmii_clk_ck";
 		clock-frequency = <0>;
 	};
 
-	sdvenc_clkin_ck: sdvenc_clkin_ck {
+	sdvenc_clkin_ck: clock-sdvenc-clkin {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "sdvenc_clkin_ck";
 		clock-frequency = <0>;
 	};
 
-	secure_32k_clk_src_ck: secure_32k_clk_src_ck {
+	secure_32k_clk_src_ck: clock-secure-32k-clk-src {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "secure_32k_clk_src_ck";
 		clock-frequency = <32768>;
 	};
 
-	sys_clk32_crystal_ck: sys_clk32_crystal_ck {
+	sys_clk32_crystal_ck: clock-sys-clk32-crystal {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "sys_clk32_crystal_ck";
 		clock-frequency = <32768>;
 	};
 
-	sys_clk32_pseudo_ck: sys_clk32_pseudo_ck {
+	sys_clk32_pseudo_ck: clock-sys-clk32-pseudo {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "sys_clk32_pseudo_ck";
 		clocks = <&sys_clkin1>;
 		clock-mult = <1>;
 		clock-div = <610>;
 	};
 
-	virt_12000000_ck: virt_12000000_ck {
+	virt_12000000_ck: clock-virt-12000000 {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "virt_12000000_ck";
 		clock-frequency = <12000000>;
 	};
 
-	virt_13000000_ck: virt_13000000_ck {
+	virt_13000000_ck: clock-virt-13000000 {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "virt_13000000_ck";
 		clock-frequency = <13000000>;
 	};
 
-	virt_16800000_ck: virt_16800000_ck {
+	virt_16800000_ck: clock-virt-16800000 {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "virt_16800000_ck";
 		clock-frequency = <16800000>;
 	};
 
-	virt_19200000_ck: virt_19200000_ck {
+	virt_19200000_ck: clock-virt-19200000 {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "virt_19200000_ck";
 		clock-frequency = <19200000>;
 	};
 
-	virt_20000000_ck: virt_20000000_ck {
+	virt_20000000_ck: clock-virt-20000000 {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "virt_20000000_ck";
 		clock-frequency = <20000000>;
 	};
 
-	virt_26000000_ck: virt_26000000_ck {
+	virt_26000000_ck: clock-virt-26000000 {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "virt_26000000_ck";
 		clock-frequency = <26000000>;
 	};
 
-	virt_27000000_ck: virt_27000000_ck {
+	virt_27000000_ck: clock-virt-27000000 {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "virt_27000000_ck";
 		clock-frequency = <27000000>;
 	};
 
-	virt_38400000_ck: virt_38400000_ck {
+	virt_38400000_ck: clock-virt-38400000 {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "virt_38400000_ck";
 		clock-frequency = <38400000>;
 	};
 
-	sys_clkin2: sys_clkin2 {
+	sys_clkin2: clock-sys-clkin2 {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "sys_clkin2";
 		clock-frequency = <22579200>;
 	};
 
-	usb_otg_clkin_ck: usb_otg_clkin_ck {
+	usb_otg_clkin_ck: clock-usb-otg-clkin {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "usb_otg_clkin_ck";
 		clock-frequency = <0>;
 	};
 
-	video1_clkin_ck: video1_clkin_ck {
+	video1_clkin_ck: clock-video1-clkin {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "video1_clkin_ck";
 		clock-frequency = <0>;
 	};
 
-	video1_m2_clkin_ck: video1_m2_clkin_ck {
+	video1_m2_clkin_ck: clock-video1-m2-clkin {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "video1_m2_clkin_ck";
 		clock-frequency = <0>;
 	};
 
-	video2_clkin_ck: video2_clkin_ck {
+	video2_clkin_ck: clock-video2-clkin {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "video2_clkin_ck";
 		clock-frequency = <0>;
 	};
 
-	video2_m2_clkin_ck: video2_m2_clkin_ck {
+	video2_m2_clkin_ck: clock-video2-m2-clkin {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "video2_m2_clkin_ck";
 		clock-frequency = <0>;
 	};
 
-	dpll_abe_ck: dpll_abe_ck@1e0 {
+	dpll_abe_ck: clock@1e0 {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-m4xen-clock";
+		clock-output-names = "dpll_abe_ck";
 		clocks = <&abe_dpll_clk_mux>, <&abe_dpll_bypass_clk_mux>;
 		reg = <0x01e0>, <0x01e4>, <0x01ec>, <0x01e8>;
 	};
 
-	dpll_abe_x2_ck: dpll_abe_x2_ck {
+	dpll_abe_x2_ck: clock-dpll-abe-x2 {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-x2-clock";
+		clock-output-names = "dpll_abe_x2_ck";
 		clocks = <&dpll_abe_ck>;
 	};
 
-	dpll_abe_m2x2_ck: dpll_abe_m2x2_ck@1f0 {
+	dpll_abe_m2x2_ck: clock-dpll-abe-m2x2-8@1f0 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_abe_m2x2_ck";
 		clocks = <&dpll_abe_x2_ck>;
 		ti,max-div = <31>;
 		ti,autoidle-shift = <8>;
@@ -217,18 +251,20 @@
 		ti,invert-autoidle-bit;
 	};
 
-	abe_clk: abe_clk@108 {
+	abe_clk: clock-abe@108 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "abe_clk";
 		clocks = <&dpll_abe_m2x2_ck>;
 		ti,max-div = <4>;
 		reg = <0x0108>;
 		ti,index-power-of-two;
 	};
 
-	dpll_abe_m2_ck: dpll_abe_m2_ck@1f0 {
+	dpll_abe_m2_ck: clock-dpll-abe-m2-8@1f0 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_abe_m2_ck";
 		clocks = <&dpll_abe_ck>;
 		ti,max-div = <31>;
 		ti,autoidle-shift = <8>;
@@ -237,9 +273,10 @@
 		ti,invert-autoidle-bit;
 	};
 
-	dpll_abe_m3x2_ck: dpll_abe_m3x2_ck@1f4 {
+	dpll_abe_m3x2_ck: clock-dpll-abe-m3x2-8@1f4 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_abe_m3x2_ck";
 		clocks = <&dpll_abe_x2_ck>;
 		ti,max-div = <31>;
 		ti,autoidle-shift = <8>;
@@ -248,30 +285,34 @@
 		ti,invert-autoidle-bit;
 	};
 
-	dpll_core_byp_mux: dpll_core_byp_mux@12c {
+	dpll_core_byp_mux: clock-dpll-core-byp-mux-23@12c {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "dpll_core_byp_mux";
 		clocks = <&sys_clkin1>, <&dpll_abe_m3x2_ck>;
 		ti,bit-shift = <23>;
 		reg = <0x012c>;
 	};
 
-	dpll_core_ck: dpll_core_ck@120 {
+	dpll_core_ck: clock@120 {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-core-clock";
+		clock-output-names = "dpll_core_ck";
 		clocks = <&sys_clkin1>, <&dpll_core_byp_mux>;
 		reg = <0x0120>, <0x0124>, <0x012c>, <0x0128>;
 	};
 
-	dpll_core_x2_ck: dpll_core_x2_ck {
+	dpll_core_x2_ck: clock-dpll-core-x2 {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-x2-clock";
+		clock-output-names = "dpll_core_x2_ck";
 		clocks = <&dpll_core_ck>;
 	};
 
-	dpll_core_h12x2_ck: dpll_core_h12x2_ck@13c {
+	dpll_core_h12x2_ck: clock-dpll-core-h12x2-8@13c {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_core_h12x2_ck";
 		clocks = <&dpll_core_x2_ck>;
 		ti,max-div = <63>;
 		ti,autoidle-shift = <8>;
@@ -280,24 +321,27 @@
 		ti,invert-autoidle-bit;
 	};
 
-	mpu_dpll_hs_clk_div: mpu_dpll_hs_clk_div {
+	mpu_dpll_hs_clk_div: clock-mpu-dpll-hs-clk-div {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "mpu_dpll_hs_clk_div";
 		clocks = <&dpll_core_h12x2_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	dpll_mpu_ck: dpll_mpu_ck@160 {
+	dpll_mpu_ck: clock@160 {
 		#clock-cells = <0>;
 		compatible = "ti,omap5-mpu-dpll-clock";
+		clock-output-names = "dpll_mpu_ck";
 		clocks = <&sys_clkin1>, <&mpu_dpll_hs_clk_div>;
 		reg = <0x0160>, <0x0164>, <0x016c>, <0x0168>;
 	};
 
-	dpll_mpu_m2_ck: dpll_mpu_m2_ck@170 {
+	dpll_mpu_m2_ck: clock-dpll-mpu-m2-8@170 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_mpu_m2_ck";
 		clocks = <&dpll_mpu_ck>;
 		ti,max-div = <31>;
 		ti,autoidle-shift = <8>;
@@ -306,42 +350,47 @@
 		ti,invert-autoidle-bit;
 	};
 
-	mpu_dclk_div: mpu_dclk_div {
+	mpu_dclk_div: clock-mpu-dclk-div {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "mpu_dclk_div";
 		clocks = <&dpll_mpu_m2_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	dsp_dpll_hs_clk_div: dsp_dpll_hs_clk_div {
+	dsp_dpll_hs_clk_div: clock-dsp-dpll-hs-clk-div {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "dsp_dpll_hs_clk_div";
 		clocks = <&dpll_core_h12x2_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	dpll_dsp_byp_mux: dpll_dsp_byp_mux@240 {
+	dpll_dsp_byp_mux: clock-dpll-dsp-byp-mux-23@240 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "dpll_dsp_byp_mux";
 		clocks = <&sys_clkin1>, <&dsp_dpll_hs_clk_div>;
 		ti,bit-shift = <23>;
 		reg = <0x0240>;
 	};
 
-	dpll_dsp_ck: dpll_dsp_ck@234 {
+	dpll_dsp_ck: clock@234 {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-clock";
+		clock-output-names = "dpll_dsp_ck";
 		clocks = <&sys_clkin1>, <&dpll_dsp_byp_mux>;
 		reg = <0x0234>, <0x0238>, <0x0240>, <0x023c>;
 		assigned-clocks = <&dpll_dsp_ck>;
 		assigned-clock-rates = <600000000>;
 	};
 
-	dpll_dsp_m2_ck: dpll_dsp_m2_ck@244 {
+	dpll_dsp_m2_ck: clock-dpll-dsp-m2-8@244 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_dsp_m2_ck";
 		clocks = <&dpll_dsp_ck>;
 		ti,max-div = <31>;
 		ti,autoidle-shift = <8>;
@@ -352,34 +401,38 @@
 		assigned-clock-rates = <600000000>;
 	};
 
-	iva_dpll_hs_clk_div: iva_dpll_hs_clk_div {
+	iva_dpll_hs_clk_div: clock-iva-dpll-hs-clk-div {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "iva_dpll_hs_clk_div";
 		clocks = <&dpll_core_h12x2_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	dpll_iva_byp_mux: dpll_iva_byp_mux@1ac {
+	dpll_iva_byp_mux: clock-dpll-iva-byp-mux-23@1ac {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "dpll_iva_byp_mux";
 		clocks = <&sys_clkin1>, <&iva_dpll_hs_clk_div>;
 		ti,bit-shift = <23>;
 		reg = <0x01ac>;
 	};
 
-	dpll_iva_ck: dpll_iva_ck@1a0 {
+	dpll_iva_ck: clock@1a0 {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-clock";
+		clock-output-names = "dpll_iva_ck";
 		clocks = <&sys_clkin1>, <&dpll_iva_byp_mux>;
 		reg = <0x01a0>, <0x01a4>, <0x01ac>, <0x01a8>;
 		assigned-clocks = <&dpll_iva_ck>;
 		assigned-clock-rates = <1165000000>;
 	};
 
-	dpll_iva_m2_ck: dpll_iva_m2_ck@1b0 {
+	dpll_iva_m2_ck: clock-dpll-iva-m2-8@1b0 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_iva_m2_ck";
 		clocks = <&dpll_iva_ck>;
 		ti,max-div = <31>;
 		ti,autoidle-shift = <8>;
@@ -390,34 +443,38 @@
 		assigned-clock-rates = <388333334>;
 	};
 
-	iva_dclk: iva_dclk {
+	iva_dclk: clock-iva-dclk {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "iva_dclk";
 		clocks = <&dpll_iva_m2_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	dpll_gpu_byp_mux: dpll_gpu_byp_mux@2e4 {
+	dpll_gpu_byp_mux: clock-dpll-gpu-byp-mux-23@2e4 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "dpll_gpu_byp_mux";
 		clocks = <&sys_clkin1>, <&dpll_abe_m3x2_ck>;
 		ti,bit-shift = <23>;
 		reg = <0x02e4>;
 	};
 
-	dpll_gpu_ck: dpll_gpu_ck@2d8 {
+	dpll_gpu_ck: clock@2d8 {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-clock";
+		clock-output-names = "dpll_gpu_ck";
 		clocks = <&sys_clkin1>, <&dpll_gpu_byp_mux>;
 		reg = <0x02d8>, <0x02dc>, <0x02e4>, <0x02e0>;
 		assigned-clocks = <&dpll_gpu_ck>;
 		assigned-clock-rates = <1277000000>;
 	};
 
-	dpll_gpu_m2_ck: dpll_gpu_m2_ck@2e8 {
+	dpll_gpu_m2_ck: clock-dpll-gpu-m2-8@2e8 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_gpu_m2_ck";
 		clocks = <&dpll_gpu_ck>;
 		ti,max-div = <31>;
 		ti,autoidle-shift = <8>;
@@ -428,9 +485,10 @@
 		assigned-clock-rates = <425666667>;
 	};
 
-	dpll_core_m2_ck: dpll_core_m2_ck@130 {
+	dpll_core_m2_ck: clock-dpll-core-m2-8@130 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_core_m2_ck";
 		clocks = <&dpll_core_ck>;
 		ti,max-div = <31>;
 		ti,autoidle-shift = <8>;
@@ -439,32 +497,36 @@
 		ti,invert-autoidle-bit;
 	};
 
-	core_dpll_out_dclk_div: core_dpll_out_dclk_div {
+	core_dpll_out_dclk_div: clock-core-dpll-out-dclk-div {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "core_dpll_out_dclk_div";
 		clocks = <&dpll_core_m2_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	dpll_ddr_byp_mux: dpll_ddr_byp_mux@21c {
+	dpll_ddr_byp_mux: clock-dpll-ddr-byp-mux-23@21c {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "dpll_ddr_byp_mux";
 		clocks = <&sys_clkin1>, <&dpll_abe_m3x2_ck>;
 		ti,bit-shift = <23>;
 		reg = <0x021c>;
 	};
 
-	dpll_ddr_ck: dpll_ddr_ck@210 {
+	dpll_ddr_ck: clock@210 {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-clock";
+		clock-output-names = "dpll_ddr_ck";
 		clocks = <&sys_clkin1>, <&dpll_ddr_byp_mux>;
 		reg = <0x0210>, <0x0214>, <0x021c>, <0x0218>;
 	};
 
-	dpll_ddr_m2_ck: dpll_ddr_m2_ck@220 {
+	dpll_ddr_m2_ck: clock-dpll-ddr-m2-8@220 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_ddr_m2_ck";
 		clocks = <&dpll_ddr_ck>;
 		ti,max-div = <31>;
 		ti,autoidle-shift = <8>;
@@ -473,24 +535,27 @@
 		ti,invert-autoidle-bit;
 	};
 
-	dpll_gmac_byp_mux: dpll_gmac_byp_mux@2b4 {
+	dpll_gmac_byp_mux: clock-dpll-gmac-byp-mux-23@2b4 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "dpll_gmac_byp_mux";
 		clocks = <&sys_clkin1>, <&dpll_abe_m3x2_ck>;
 		ti,bit-shift = <23>;
 		reg = <0x02b4>;
 	};
 
-	dpll_gmac_ck: dpll_gmac_ck@2a8 {
+	dpll_gmac_ck: clock@2a8 {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-clock";
+		clock-output-names = "dpll_gmac_ck";
 		clocks = <&sys_clkin1>, <&dpll_gmac_byp_mux>;
 		reg = <0x02a8>, <0x02ac>, <0x02b4>, <0x02b0>;
 	};
 
-	dpll_gmac_m2_ck: dpll_gmac_m2_ck@2b8 {
+	dpll_gmac_m2_ck: clock-dpll-gmac-m2-8@2b8 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_gmac_m2_ck";
 		clocks = <&dpll_gmac_ck>;
 		ti,max-div = <31>;
 		ti,autoidle-shift = <8>;
@@ -499,72 +564,81 @@
 		ti,invert-autoidle-bit;
 	};
 
-	video2_dclk_div: video2_dclk_div {
+	video2_dclk_div: clock-video2-dclk-div {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "video2_dclk_div";
 		clocks = <&video2_m2_clkin_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	video1_dclk_div: video1_dclk_div {
+	video1_dclk_div: clock-video1-dclk-div {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "video1_dclk_div";
 		clocks = <&video1_m2_clkin_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	hdmi_dclk_div: hdmi_dclk_div {
+	hdmi_dclk_div: clock-hdmi-dclk-div {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "hdmi_dclk_div";
 		clocks = <&hdmi_clkin_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	per_dpll_hs_clk_div: per_dpll_hs_clk_div {
+	per_dpll_hs_clk_div: clock-per-dpll-hs-clk-div {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "per_dpll_hs_clk_div";
 		clocks = <&dpll_abe_m3x2_ck>;
 		clock-mult = <1>;
 		clock-div = <2>;
 	};
 
-	usb_dpll_hs_clk_div: usb_dpll_hs_clk_div {
+	usb_dpll_hs_clk_div: clock-usb-dpll-hs-clk-div {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "usb_dpll_hs_clk_div";
 		clocks = <&dpll_abe_m3x2_ck>;
 		clock-mult = <1>;
 		clock-div = <3>;
 	};
 
-	eve_dpll_hs_clk_div: eve_dpll_hs_clk_div {
+	eve_dpll_hs_clk_div: clock-eve-dpll-hs-clk-div {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "eve_dpll_hs_clk_div";
 		clocks = <&dpll_core_h12x2_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	dpll_eve_byp_mux: dpll_eve_byp_mux@290 {
+	dpll_eve_byp_mux: clock-dpll-eve-byp-mux-23@290 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "dpll_eve_byp_mux";
 		clocks = <&sys_clkin1>, <&eve_dpll_hs_clk_div>;
 		ti,bit-shift = <23>;
 		reg = <0x0290>;
 	};
 
-	dpll_eve_ck: dpll_eve_ck@284 {
+	dpll_eve_ck: clock@284 {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-clock";
+		clock-output-names = "dpll_eve_ck";
 		clocks = <&sys_clkin1>, <&dpll_eve_byp_mux>;
 		reg = <0x0284>, <0x0288>, <0x0290>, <0x028c>;
 	};
 
-	dpll_eve_m2_ck: dpll_eve_m2_ck@294 {
+	dpll_eve_m2_ck: clock-dpll-eve-m2-8@294 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_eve_m2_ck";
 		clocks = <&dpll_eve_ck>;
 		ti,max-div = <31>;
 		ti,autoidle-shift = <8>;
@@ -573,17 +647,19 @@
 		ti,invert-autoidle-bit;
 	};
 
-	eve_dclk_div: eve_dclk_div {
+	eve_dclk_div: clock-eve-dclk-div {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "eve_dclk_div";
 		clocks = <&dpll_eve_m2_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	dpll_core_h13x2_ck: dpll_core_h13x2_ck@140 {
+	dpll_core_h13x2_ck: clock-dpll-core-h13x2-8@140 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_core_h13x2_ck";
 		clocks = <&dpll_core_x2_ck>;
 		ti,max-div = <63>;
 		ti,autoidle-shift = <8>;
@@ -592,9 +668,10 @@
 		ti,invert-autoidle-bit;
 	};
 
-	dpll_core_h14x2_ck: dpll_core_h14x2_ck@144 {
+	dpll_core_h14x2_ck: clock-dpll-core-h14x2-8@144 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_core_h14x2_ck";
 		clocks = <&dpll_core_x2_ck>;
 		ti,max-div = <63>;
 		ti,autoidle-shift = <8>;
@@ -603,9 +680,10 @@
 		ti,invert-autoidle-bit;
 	};
 
-	dpll_core_h22x2_ck: dpll_core_h22x2_ck@154 {
+	dpll_core_h22x2_ck: clock-dpll-core-h22x2-8@154 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_core_h22x2_ck";
 		clocks = <&dpll_core_x2_ck>;
 		ti,max-div = <63>;
 		ti,autoidle-shift = <8>;
@@ -614,9 +692,10 @@
 		ti,invert-autoidle-bit;
 	};
 
-	dpll_core_h23x2_ck: dpll_core_h23x2_ck@158 {
+	dpll_core_h23x2_ck: clock-dpll-core-h23x2-8@158 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_core_h23x2_ck";
 		clocks = <&dpll_core_x2_ck>;
 		ti,max-div = <63>;
 		ti,autoidle-shift = <8>;
@@ -625,9 +704,10 @@
 		ti,invert-autoidle-bit;
 	};
 
-	dpll_core_h24x2_ck: dpll_core_h24x2_ck@15c {
+	dpll_core_h24x2_ck: clock-dpll-core-h24x2-8@15c {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_core_h24x2_ck";
 		clocks = <&dpll_core_x2_ck>;
 		ti,max-div = <63>;
 		ti,autoidle-shift = <8>;
@@ -636,15 +716,17 @@
 		ti,invert-autoidle-bit;
 	};
 
-	dpll_ddr_x2_ck: dpll_ddr_x2_ck {
+	dpll_ddr_x2_ck: clock-dpll-ddr-x2 {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-x2-clock";
+		clock-output-names = "dpll_ddr_x2_ck";
 		clocks = <&dpll_ddr_ck>;
 	};
 
-	dpll_ddr_h11x2_ck: dpll_ddr_h11x2_ck@228 {
+	dpll_ddr_h11x2_ck: clock-dpll-ddr-h11x2-8@228 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_ddr_h11x2_ck";
 		clocks = <&dpll_ddr_x2_ck>;
 		ti,max-div = <63>;
 		ti,autoidle-shift = <8>;
@@ -653,15 +735,17 @@
 		ti,invert-autoidle-bit;
 	};
 
-	dpll_dsp_x2_ck: dpll_dsp_x2_ck {
+	dpll_dsp_x2_ck: clock-dpll-dsp-x2 {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-x2-clock";
+		clock-output-names = "dpll_dsp_x2_ck";
 		clocks = <&dpll_dsp_ck>;
 	};
 
-	dpll_dsp_m3x2_ck: dpll_dsp_m3x2_ck@248 {
+	dpll_dsp_m3x2_ck: clock-dpll-dsp-m3x2-8@248 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_dsp_m3x2_ck";
 		clocks = <&dpll_dsp_x2_ck>;
 		ti,max-div = <31>;
 		ti,autoidle-shift = <8>;
@@ -672,15 +756,17 @@
 		assigned-clock-rates = <400000000>;
 	};
 
-	dpll_gmac_x2_ck: dpll_gmac_x2_ck {
+	dpll_gmac_x2_ck: clock-dpll-gmac-x2 {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-x2-clock";
+		clock-output-names = "dpll_gmac_x2_ck";
 		clocks = <&dpll_gmac_ck>;
 	};
 
-	dpll_gmac_h11x2_ck: dpll_gmac_h11x2_ck@2c0 {
+	dpll_gmac_h11x2_ck: clock-dpll-gmac-h11x2-8@2c0 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_gmac_h11x2_ck";
 		clocks = <&dpll_gmac_x2_ck>;
 		ti,max-div = <63>;
 		ti,autoidle-shift = <8>;
@@ -689,9 +775,10 @@
 		ti,invert-autoidle-bit;
 	};
 
-	dpll_gmac_h12x2_ck: dpll_gmac_h12x2_ck@2c4 {
+	dpll_gmac_h12x2_ck: clock-dpll-gmac-h12x2-8@2c4 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_gmac_h12x2_ck";
 		clocks = <&dpll_gmac_x2_ck>;
 		ti,max-div = <63>;
 		ti,autoidle-shift = <8>;
@@ -700,9 +787,10 @@
 		ti,invert-autoidle-bit;
 	};
 
-	dpll_gmac_h13x2_ck: dpll_gmac_h13x2_ck@2c8 {
+	dpll_gmac_h13x2_ck: clock-dpll-gmac-h13x2-8@2c8 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_gmac_h13x2_ck";
 		clocks = <&dpll_gmac_x2_ck>;
 		ti,max-div = <63>;
 		ti,autoidle-shift = <8>;
@@ -711,9 +799,10 @@
 		ti,invert-autoidle-bit;
 	};
 
-	dpll_gmac_m3x2_ck: dpll_gmac_m3x2_ck@2bc {
+	dpll_gmac_m3x2_ck: clock-dpll-gmac-m3x2-8@2bc {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_gmac_m3x2_ck";
 		clocks = <&dpll_gmac_x2_ck>;
 		ti,max-div = <31>;
 		ti,autoidle-shift = <8>;
@@ -722,33 +811,37 @@
 		ti,invert-autoidle-bit;
 	};
 
-	gmii_m_clk_div: gmii_m_clk_div {
+	gmii_m_clk_div: clock-gmii-m-clk-div {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "gmii_m_clk_div";
 		clocks = <&dpll_gmac_h11x2_ck>;
 		clock-mult = <1>;
 		clock-div = <2>;
 	};
 
-	hdmi_clk2_div: hdmi_clk2_div {
+	hdmi_clk2_div: clock-hdmi-clk2-div {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "hdmi_clk2_div";
 		clocks = <&hdmi_clkin_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	hdmi_div_clk: hdmi_div_clk {
+	hdmi_div_clk: clock-hdmi-div {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "hdmi_div_clk";
 		clocks = <&hdmi_clkin_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	l3_iclk_div: l3_iclk_div@100 {
+	l3_iclk_div: clock-l3-iclk-div-4@100 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "l3_iclk_div";
 		ti,max-div = <2>;
 		ti,bit-shift = <4>;
 		reg = <0x0100>;
@@ -756,374 +849,420 @@
 		ti,index-power-of-two;
 	};
 
-	l4_root_clk_div: l4_root_clk_div {
+	l4_root_clk_div: clock-l4-root-clk-div {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "l4_root_clk_div";
 		clocks = <&l3_iclk_div>;
 		clock-mult = <1>;
 		clock-div = <2>;
 	};
 
-	video1_clk2_div: video1_clk2_div {
+	video1_clk2_div: clock-video1-clk2-div {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "video1_clk2_div";
 		clocks = <&video1_clkin_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	video1_div_clk: video1_div_clk {
+	video1_div_clk: clock-video1-div {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "video1_div_clk";
 		clocks = <&video1_clkin_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	video2_clk2_div: video2_clk2_div {
+	video2_clk2_div: clock-video2-clk2-div {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "video2_clk2_div";
 		clocks = <&video2_clkin_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	video2_div_clk: video2_div_clk {
+	video2_div_clk: clock-video2-div {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "video2_div_clk";
 		clocks = <&video2_clkin_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	dummy_ck: dummy_ck {
+	dummy_ck: clock-dummy {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "dummy_ck";
 		clock-frequency = <0>;
 	};
 };
 &prm_clocks {
-	sys_clkin1: sys_clkin1@110 {
+	sys_clkin1: clock-sys-clkin1@110 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "sys_clkin1";
 		clocks = <&virt_12000000_ck>, <&virt_20000000_ck>, <&virt_16800000_ck>, <&virt_19200000_ck>, <&virt_26000000_ck>, <&virt_27000000_ck>, <&virt_38400000_ck>;
 		reg = <0x0110>;
 		ti,index-starts-at-one;
 	};
 
-	abe_dpll_sys_clk_mux: abe_dpll_sys_clk_mux@118 {
+	abe_dpll_sys_clk_mux: clock-abe-dpll-sys-clk-mux@118 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "abe_dpll_sys_clk_mux";
 		clocks = <&sys_clkin1>, <&sys_clkin2>;
 		reg = <0x0118>;
 	};
 
-	abe_dpll_bypass_clk_mux: abe_dpll_bypass_clk_mux@114 {
+	abe_dpll_bypass_clk_mux: clock-abe-dpll-bypass-clk-mux@114 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "abe_dpll_bypass_clk_mux";
 		clocks = <&abe_dpll_sys_clk_mux>, <&sys_32k_ck>;
 		reg = <0x0114>;
 	};
 
-	abe_dpll_clk_mux: abe_dpll_clk_mux@10c {
+	abe_dpll_clk_mux: clock-abe-dpll-clk-mux@10c {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "abe_dpll_clk_mux";
 		clocks = <&abe_dpll_sys_clk_mux>, <&sys_32k_ck>;
 		reg = <0x010c>;
 	};
 
-	abe_24m_fclk: abe_24m_fclk@11c {
+	abe_24m_fclk: clock-abe-24m@11c {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "abe_24m_fclk";
 		clocks = <&dpll_abe_m2x2_ck>;
 		reg = <0x011c>;
 		ti,dividers = <8>, <16>;
 	};
 
-	aess_fclk: aess_fclk@178 {
+	aess_fclk: clock-aess@178 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "aess_fclk";
 		clocks = <&abe_clk>;
 		reg = <0x0178>;
 		ti,max-div = <2>;
 	};
 
-	abe_giclk_div: abe_giclk_div@174 {
+	abe_giclk_div: clock-abe-giclk-div@174 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "abe_giclk_div";
 		clocks = <&aess_fclk>;
 		reg = <0x0174>;
 		ti,max-div = <2>;
 	};
 
-	abe_lp_clk_div: abe_lp_clk_div@1d8 {
+	abe_lp_clk_div: clock-abe-lp-clk-div@1d8 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "abe_lp_clk_div";
 		clocks = <&dpll_abe_m2x2_ck>;
 		reg = <0x01d8>;
 		ti,dividers = <16>, <32>;
 	};
 
-	abe_sys_clk_div: abe_sys_clk_div@120 {
+	abe_sys_clk_div: clock-abe-sys-clk-div@120 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "abe_sys_clk_div";
 		clocks = <&sys_clkin1>;
 		reg = <0x0120>;
 		ti,max-div = <2>;
 	};
 
-	adc_gfclk_mux: adc_gfclk_mux@1dc {
+	adc_gfclk_mux: clock-adc-gfclk-mux@1dc {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "adc_gfclk_mux";
 		clocks = <&sys_clkin1>, <&sys_clkin2>, <&sys_32k_ck>;
 		reg = <0x01dc>;
 	};
 
-	sys_clk1_dclk_div: sys_clk1_dclk_div@1c8 {
+	sys_clk1_dclk_div: clock-sys-clk1-dclk-div@1c8 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "sys_clk1_dclk_div";
 		clocks = <&sys_clkin1>;
 		ti,max-div = <64>;
 		reg = <0x01c8>;
 		ti,index-power-of-two;
 	};
 
-	sys_clk2_dclk_div: sys_clk2_dclk_div@1cc {
+	sys_clk2_dclk_div: clock-sys-clk2-dclk-div@1cc {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "sys_clk2_dclk_div";
 		clocks = <&sys_clkin2>;
 		ti,max-div = <64>;
 		reg = <0x01cc>;
 		ti,index-power-of-two;
 	};
 
-	per_abe_x1_dclk_div: per_abe_x1_dclk_div@1bc {
+	per_abe_x1_dclk_div: clock-per-abe-x1-dclk-div@1bc {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "per_abe_x1_dclk_div";
 		clocks = <&dpll_abe_m2_ck>;
 		ti,max-div = <64>;
 		reg = <0x01bc>;
 		ti,index-power-of-two;
 	};
 
-	dsp_gclk_div: dsp_gclk_div@18c {
+	dsp_gclk_div: clock-dsp-gclk-div@18c {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dsp_gclk_div";
 		clocks = <&dpll_dsp_m2_ck>;
 		ti,max-div = <64>;
 		reg = <0x018c>;
 		ti,index-power-of-two;
 	};
 
-	gpu_dclk: gpu_dclk@1a0 {
+	gpu_dclk: clock-gpu-dclk@1a0 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "gpu_dclk";
 		clocks = <&dpll_gpu_m2_ck>;
 		ti,max-div = <64>;
 		reg = <0x01a0>;
 		ti,index-power-of-two;
 	};
 
-	emif_phy_dclk_div: emif_phy_dclk_div@190 {
+	emif_phy_dclk_div: clock-emif-phy-dclk-div@190 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "emif_phy_dclk_div";
 		clocks = <&dpll_ddr_m2_ck>;
 		ti,max-div = <64>;
 		reg = <0x0190>;
 		ti,index-power-of-two;
 	};
 
-	gmac_250m_dclk_div: gmac_250m_dclk_div@19c {
+	gmac_250m_dclk_div: clock-gmac-250m-dclk-div@19c {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "gmac_250m_dclk_div";
 		clocks = <&dpll_gmac_m2_ck>;
 		ti,max-div = <64>;
 		reg = <0x019c>;
 		ti,index-power-of-two;
 	};
 
-	gmac_main_clk: gmac_main_clk {
+	gmac_main_clk: clock-gmac-main {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "gmac_main_clk";
 		clocks = <&gmac_250m_dclk_div>;
 		clock-mult = <1>;
 		clock-div = <2>;
 	};
 
-	l3init_480m_dclk_div: l3init_480m_dclk_div@1ac {
+	l3init_480m_dclk_div: clock-l3init-480m-dclk-div@1ac {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "l3init_480m_dclk_div";
 		clocks = <&dpll_usb_m2_ck>;
 		ti,max-div = <64>;
 		reg = <0x01ac>;
 		ti,index-power-of-two;
 	};
 
-	usb_otg_dclk_div: usb_otg_dclk_div@184 {
+	usb_otg_dclk_div: clock-usb-otg-dclk-div@184 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "usb_otg_dclk_div";
 		clocks = <&usb_otg_clkin_ck>;
 		ti,max-div = <64>;
 		reg = <0x0184>;
 		ti,index-power-of-two;
 	};
 
-	sata_dclk_div: sata_dclk_div@1c0 {
+	sata_dclk_div: clock-sata-dclk-div@1c0 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "sata_dclk_div";
 		clocks = <&sys_clkin1>;
 		ti,max-div = <64>;
 		reg = <0x01c0>;
 		ti,index-power-of-two;
 	};
 
-	pcie2_dclk_div: pcie2_dclk_div@1b8 {
+	pcie2_dclk_div: clock-pcie2-dclk-div@1b8 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "pcie2_dclk_div";
 		clocks = <&dpll_pcie_ref_m2_ck>;
 		ti,max-div = <64>;
 		reg = <0x01b8>;
 		ti,index-power-of-two;
 	};
 
-	pcie_dclk_div: pcie_dclk_div@1b4 {
+	pcie_dclk_div: clock-pcie-dclk-div@1b4 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "pcie_dclk_div";
 		clocks = <&apll_pcie_m2_ck>;
 		ti,max-div = <64>;
 		reg = <0x01b4>;
 		ti,index-power-of-two;
 	};
 
-	emu_dclk_div: emu_dclk_div@194 {
+	emu_dclk_div: clock-emu-dclk-div@194 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "emu_dclk_div";
 		clocks = <&sys_clkin1>;
 		ti,max-div = <64>;
 		reg = <0x0194>;
 		ti,index-power-of-two;
 	};
 
-	secure_32k_dclk_div: secure_32k_dclk_div@1c4 {
+	secure_32k_dclk_div: clock-secure-32k-dclk-div@1c4 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "secure_32k_dclk_div";
 		clocks = <&secure_32k_clk_src_ck>;
 		ti,max-div = <64>;
 		reg = <0x01c4>;
 		ti,index-power-of-two;
 	};
 
-	clkoutmux0_clk_mux: clkoutmux0_clk_mux@158 {
+	clkoutmux0_clk_mux: clock-clkoutmux0-clk-mux@158 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "clkoutmux0_clk_mux";
 		clocks = <&sys_clk1_dclk_div>, <&sys_clk2_dclk_div>, <&per_abe_x1_dclk_div>, <&mpu_dclk_div>, <&dsp_gclk_div>, <&iva_dclk>, <&gpu_dclk>, <&core_dpll_out_dclk_div>, <&emif_phy_dclk_div>, <&gmac_250m_dclk_div>, <&video2_dclk_div>, <&video1_dclk_div>, <&hdmi_dclk_div>, <&func_96m_aon_dclk_div>, <&l3init_480m_dclk_div>, <&usb_otg_dclk_div>, <&sata_dclk_div>, <&pcie2_dclk_div>, <&pcie_dclk_div>, <&emu_dclk_div>, <&secure_32k_dclk_div>, <&eve_dclk_div>;
 		reg = <0x0158>;
 	};
 
-	clkoutmux1_clk_mux: clkoutmux1_clk_mux@15c {
+	clkoutmux1_clk_mux: clock-clkoutmux1-clk-mux@15c {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "clkoutmux1_clk_mux";
 		clocks = <&sys_clk1_dclk_div>, <&sys_clk2_dclk_div>, <&per_abe_x1_dclk_div>, <&mpu_dclk_div>, <&dsp_gclk_div>, <&iva_dclk>, <&gpu_dclk>, <&core_dpll_out_dclk_div>, <&emif_phy_dclk_div>, <&gmac_250m_dclk_div>, <&video2_dclk_div>, <&video1_dclk_div>, <&hdmi_dclk_div>, <&func_96m_aon_dclk_div>, <&l3init_480m_dclk_div>, <&usb_otg_dclk_div>, <&sata_dclk_div>, <&pcie2_dclk_div>, <&pcie_dclk_div>, <&emu_dclk_div>, <&secure_32k_dclk_div>, <&eve_dclk_div>;
 		reg = <0x015c>;
 	};
 
-	clkoutmux2_clk_mux: clkoutmux2_clk_mux@160 {
+	clkoutmux2_clk_mux: clock-clkoutmux2-clk-mux@160 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "clkoutmux2_clk_mux";
 		clocks = <&sys_clk1_dclk_div>, <&sys_clk2_dclk_div>, <&per_abe_x1_dclk_div>, <&mpu_dclk_div>, <&dsp_gclk_div>, <&iva_dclk>, <&gpu_dclk>, <&core_dpll_out_dclk_div>, <&emif_phy_dclk_div>, <&gmac_250m_dclk_div>, <&video2_dclk_div>, <&video1_dclk_div>, <&hdmi_dclk_div>, <&func_96m_aon_dclk_div>, <&l3init_480m_dclk_div>, <&usb_otg_dclk_div>, <&sata_dclk_div>, <&pcie2_dclk_div>, <&pcie_dclk_div>, <&emu_dclk_div>, <&secure_32k_dclk_div>, <&eve_dclk_div>;
 		reg = <0x0160>;
 	};
 
-	custefuse_sys_gfclk_div: custefuse_sys_gfclk_div {
+	custefuse_sys_gfclk_div: clock-custefuse-sys-gfclk-div {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "custefuse_sys_gfclk_div";
 		clocks = <&sys_clkin1>;
 		clock-mult = <1>;
 		clock-div = <2>;
 	};
 
-	eve_clk: eve_clk@180 {
+	eve_clk: clock-eve@180 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "eve_clk";
 		clocks = <&dpll_eve_m2_ck>, <&dpll_dsp_m3x2_ck>;
 		reg = <0x0180>;
 	};
 
-	hdmi_dpll_clk_mux: hdmi_dpll_clk_mux@164 {
+	hdmi_dpll_clk_mux: clock-hdmi-dpll-clk-mux@164 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "hdmi_dpll_clk_mux";
 		clocks = <&sys_clkin1>, <&sys_clkin2>;
 		reg = <0x0164>;
 	};
 
-	mlb_clk: mlb_clk@134 {
+	mlb_clk: clock-mlb@134 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "mlb_clk";
 		clocks = <&mlb_clkin_ck>;
 		ti,max-div = <64>;
 		reg = <0x0134>;
 		ti,index-power-of-two;
 	};
 
-	mlbp_clk: mlbp_clk@130 {
+	mlbp_clk: clock-mlbp@130 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "mlbp_clk";
 		clocks = <&mlbp_clkin_ck>;
 		ti,max-div = <64>;
 		reg = <0x0130>;
 		ti,index-power-of-two;
 	};
 
-	per_abe_x1_gfclk2_div: per_abe_x1_gfclk2_div@138 {
+	per_abe_x1_gfclk2_div: clock-per-abe-x1-gfclk2-div@138 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "per_abe_x1_gfclk2_div";
 		clocks = <&dpll_abe_m2_ck>;
 		ti,max-div = <64>;
 		reg = <0x0138>;
 		ti,index-power-of-two;
 	};
 
-	timer_sys_clk_div: timer_sys_clk_div@144 {
+	timer_sys_clk_div: clock-timer-sys-clk-div@144 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "timer_sys_clk_div";
 		clocks = <&sys_clkin1>;
 		reg = <0x0144>;
 		ti,max-div = <2>;
 	};
 
-	video1_dpll_clk_mux: video1_dpll_clk_mux@168 {
+	video1_dpll_clk_mux: clock-video1-dpll-clk-mux@168 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "video1_dpll_clk_mux";
 		clocks = <&sys_clkin1>, <&sys_clkin2>;
 		reg = <0x0168>;
 	};
 
-	video2_dpll_clk_mux: video2_dpll_clk_mux@16c {
+	video2_dpll_clk_mux: clock-video2-dpll-clk-mux@16c {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "video2_dpll_clk_mux";
 		clocks = <&sys_clkin1>, <&sys_clkin2>;
 		reg = <0x016c>;
 	};
 
-	wkupaon_iclk_mux: wkupaon_iclk_mux@108 {
+	wkupaon_iclk_mux: clock-wkupaon-iclk-mux@108 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "wkupaon_iclk_mux";
 		clocks = <&sys_clkin1>, <&abe_lp_clk_div>;
 		reg = <0x0108>;
 	};
 };
 
 &cm_core_clocks {
-	dpll_pcie_ref_ck: dpll_pcie_ref_ck@200 {
+	dpll_pcie_ref_ck: clock@200 {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-clock";
+		clock-output-names = "dpll_pcie_ref_ck";
 		clocks = <&sys_clkin1>, <&sys_clkin1>;
 		reg = <0x0200>, <0x0204>, <0x020c>, <0x0208>;
 	};
 
-	dpll_pcie_ref_m2ldo_ck: dpll_pcie_ref_m2ldo_ck@210 {
+	dpll_pcie_ref_m2ldo_ck: clock-dpll-pcie-ref-m2ldo-8@210 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_pcie_ref_m2ldo_ck";
 		clocks = <&dpll_pcie_ref_ck>;
 		ti,max-div = <31>;
 		ti,autoidle-shift = <8>;
@@ -1132,23 +1271,26 @@
 		ti,invert-autoidle-bit;
 	};
 
-	apll_pcie_in_clk_mux: apll_pcie_in_clk_mux@4ae06118 {
+	apll_pcie_in_clk_mux: clock-apll-pcie-in-clk-mux-7@4ae06118 {
 		compatible = "ti,mux-clock";
+		clock-output-names = "apll_pcie_in_clk_mux";
 		clocks = <&dpll_pcie_ref_m2ldo_ck>, <&pciesref_acs_clk_ck>;
 		#clock-cells = <0>;
 		reg = <0x021c 0x4>;
 		ti,bit-shift = <7>;
 	};
 
-	apll_pcie_ck: apll_pcie_ck@21c {
+	apll_pcie_ck: clock@21c {
 		#clock-cells = <0>;
 		compatible = "ti,dra7-apll-clock";
+		clock-output-names = "apll_pcie_ck";
 		clocks = <&apll_pcie_in_clk_mux>, <&dpll_pcie_ref_ck>;
 		reg = <0x021c>, <0x0220>;
 	};
 
-	optfclk_pciephy_div: optfclk_pciephy_div@4a00821c {
+	optfclk_pciephy_div: clock-optfclk-pciephy-div-8@4a00821c {
 		compatible = "ti,divider-clock";
+		clock-output-names = "optfclk_pciephy_div";
 		clocks = <&apll_pcie_ck>;
 		#clock-cells = <0>;
 		reg = <0x021c>;
@@ -1157,48 +1299,54 @@
 		ti,max-div = <2>;
 	};
 
-	apll_pcie_clkvcoldo: apll_pcie_clkvcoldo {
+	apll_pcie_clkvcoldo: clock-apll-pcie-clkvcoldo {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "apll_pcie_clkvcoldo";
 		clocks = <&apll_pcie_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	apll_pcie_clkvcoldo_div: apll_pcie_clkvcoldo_div {
+	apll_pcie_clkvcoldo_div: clock-apll-pcie-clkvcoldo-div {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "apll_pcie_clkvcoldo_div";
 		clocks = <&apll_pcie_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	apll_pcie_m2_ck: apll_pcie_m2_ck {
+	apll_pcie_m2_ck: clock-apll-pcie-m2 {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "apll_pcie_m2_ck";
 		clocks = <&apll_pcie_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	dpll_per_byp_mux: dpll_per_byp_mux@14c {
+	dpll_per_byp_mux: clock-dpll-per-byp-mux-23@14c {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "dpll_per_byp_mux";
 		clocks = <&sys_clkin1>, <&per_dpll_hs_clk_div>;
 		ti,bit-shift = <23>;
 		reg = <0x014c>;
 	};
 
-	dpll_per_ck: dpll_per_ck@140 {
+	dpll_per_ck: clock@140 {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-clock";
+		clock-output-names = "dpll_per_ck";
 		clocks = <&sys_clkin1>, <&dpll_per_byp_mux>;
 		reg = <0x0140>, <0x0144>, <0x014c>, <0x0148>;
 	};
 
-	dpll_per_m2_ck: dpll_per_m2_ck@150 {
+	dpll_per_m2_ck: clock-dpll-per-m2-8@150 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_per_m2_ck";
 		clocks = <&dpll_per_ck>;
 		ti,max-div = <31>;
 		ti,autoidle-shift = <8>;
@@ -1207,32 +1355,36 @@
 		ti,invert-autoidle-bit;
 	};
 
-	func_96m_aon_dclk_div: func_96m_aon_dclk_div {
+	func_96m_aon_dclk_div: clock-func-96m-aon-dclk-div {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "func_96m_aon_dclk_div";
 		clocks = <&dpll_per_m2_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	dpll_usb_byp_mux: dpll_usb_byp_mux@18c {
+	dpll_usb_byp_mux: clock-dpll-usb-byp-mux-23@18c {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "dpll_usb_byp_mux";
 		clocks = <&sys_clkin1>, <&usb_dpll_hs_clk_div>;
 		ti,bit-shift = <23>;
 		reg = <0x018c>;
 	};
 
-	dpll_usb_ck: dpll_usb_ck@180 {
+	dpll_usb_ck: clock@180 {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-j-type-clock";
+		clock-output-names = "dpll_usb_ck";
 		clocks = <&sys_clkin1>, <&dpll_usb_byp_mux>;
 		reg = <0x0180>, <0x0184>, <0x018c>, <0x0188>;
 	};
 
-	dpll_usb_m2_ck: dpll_usb_m2_ck@190 {
+	dpll_usb_m2_ck: clock-dpll-usb-m2-8@190 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_usb_m2_ck";
 		clocks = <&dpll_usb_ck>;
 		ti,max-div = <127>;
 		ti,autoidle-shift = <8>;
@@ -1241,9 +1393,10 @@
 		ti,invert-autoidle-bit;
 	};
 
-	dpll_pcie_ref_m2_ck: dpll_pcie_ref_m2_ck@210 {
+	dpll_pcie_ref_m2_ck: clock-dpll-pcie-ref-m2-8@210 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_pcie_ref_m2_ck";
 		clocks = <&dpll_pcie_ref_ck>;
 		ti,max-div = <127>;
 		ti,autoidle-shift = <8>;
@@ -1252,15 +1405,17 @@
 		ti,invert-autoidle-bit;
 	};
 
-	dpll_per_x2_ck: dpll_per_x2_ck {
+	dpll_per_x2_ck: clock-dpll-per-x2 {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-x2-clock";
+		clock-output-names = "dpll_per_x2_ck";
 		clocks = <&dpll_per_ck>;
 	};
 
-	dpll_per_h11x2_ck: dpll_per_h11x2_ck@158 {
+	dpll_per_h11x2_ck: clock-dpll-per-h11x2-8@158 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_per_h11x2_ck";
 		clocks = <&dpll_per_x2_ck>;
 		ti,max-div = <63>;
 		ti,autoidle-shift = <8>;
@@ -1269,9 +1424,10 @@
 		ti,invert-autoidle-bit;
 	};
 
-	dpll_per_h12x2_ck: dpll_per_h12x2_ck@15c {
+	dpll_per_h12x2_ck: clock-dpll-per-h12x2-8@15c {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_per_h12x2_ck";
 		clocks = <&dpll_per_x2_ck>;
 		ti,max-div = <63>;
 		ti,autoidle-shift = <8>;
@@ -1280,9 +1436,10 @@
 		ti,invert-autoidle-bit;
 	};
 
-	dpll_per_h13x2_ck: dpll_per_h13x2_ck@160 {
+	dpll_per_h13x2_ck: clock-dpll-per-h13x2-8@160 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_per_h13x2_ck";
 		clocks = <&dpll_per_x2_ck>;
 		ti,max-div = <63>;
 		ti,autoidle-shift = <8>;
@@ -1291,9 +1448,10 @@
 		ti,invert-autoidle-bit;
 	};
 
-	dpll_per_h14x2_ck: dpll_per_h14x2_ck@164 {
+	dpll_per_h14x2_ck: clock-dpll-per-h14x2-8@164 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_per_h14x2_ck";
 		clocks = <&dpll_per_x2_ck>;
 		ti,max-div = <63>;
 		ti,autoidle-shift = <8>;
@@ -1302,9 +1460,10 @@
 		ti,invert-autoidle-bit;
 	};
 
-	dpll_per_m2x2_ck: dpll_per_m2x2_ck@150 {
+	dpll_per_m2x2_ck: clock-dpll-per-m2x2-8@150 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_per_m2x2_ck";
 		clocks = <&dpll_per_x2_ck>;
 		ti,max-div = <31>;
 		ti,autoidle-shift = <8>;
@@ -1313,105 +1472,118 @@
 		ti,invert-autoidle-bit;
 	};
 
-	dpll_usb_clkdcoldo: dpll_usb_clkdcoldo {
+	dpll_usb_clkdcoldo: clock-dpll-usb-clkdcoldo {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "dpll_usb_clkdcoldo";
 		clocks = <&dpll_usb_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
 	};
 
-	func_128m_clk: func_128m_clk {
+	func_128m_clk: clock-func-128m {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "func_128m_clk";
 		clocks = <&dpll_per_h11x2_ck>;
 		clock-mult = <1>;
 		clock-div = <2>;
 	};
 
-	func_12m_fclk: func_12m_fclk {
+	func_12m_fclk: clock-func-12m-fclk {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "func_12m_fclk";
 		clocks = <&dpll_per_m2x2_ck>;
 		clock-mult = <1>;
 		clock-div = <16>;
 	};
 
-	func_24m_clk: func_24m_clk {
+	func_24m_clk: clock-func-24m {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "func_24m_clk";
 		clocks = <&dpll_per_m2_ck>;
 		clock-mult = <1>;
 		clock-div = <4>;
 	};
 
-	func_48m_fclk: func_48m_fclk {
+	func_48m_fclk: clock-func-48m-fclk {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "func_48m_fclk";
 		clocks = <&dpll_per_m2x2_ck>;
 		clock-mult = <1>;
 		clock-div = <4>;
 	};
 
-	func_96m_fclk: func_96m_fclk {
+	func_96m_fclk: clock-func-96m-fclk {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "func_96m_fclk";
 		clocks = <&dpll_per_m2x2_ck>;
 		clock-mult = <1>;
 		clock-div = <2>;
 	};
 
-	l3init_60m_fclk: l3init_60m_fclk@104 {
+	l3init_60m_fclk: clock-l3init-60m@104 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "l3init_60m_fclk";
 		clocks = <&dpll_usb_m2_ck>;
 		reg = <0x0104>;
 		ti,dividers = <1>, <8>;
 	};
 
-	clkout2_clk: clkout2_clk@6b0 {
+	clkout2_clk: clock-clkout2-8@6b0 {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
+		clock-output-names = "clkout2_clk";
 		clocks = <&clkoutmux2_clk_mux>;
 		ti,bit-shift = <8>;
 		reg = <0x06b0>;
 	};
 
-	l3init_960m_gfclk: l3init_960m_gfclk@6c0 {
+	l3init_960m_gfclk: clock-l3init-960m-gfclk-8@6c0 {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
+		clock-output-names = "l3init_960m_gfclk";
 		clocks = <&dpll_usb_clkdcoldo>;
 		ti,bit-shift = <8>;
 		reg = <0x06c0>;
 	};
 
-	usb_phy1_always_on_clk32k: usb_phy1_always_on_clk32k@640 {
+	usb_phy1_always_on_clk32k: clock-usb-phy1-always-on-clk32k-8@640 {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
+		clock-output-names = "usb_phy1_always_on_clk32k";
 		clocks = <&sys_32k_ck>;
 		ti,bit-shift = <8>;
 		reg = <0x0640>;
 	};
 
-	usb_phy2_always_on_clk32k: usb_phy2_always_on_clk32k@688 {
+	usb_phy2_always_on_clk32k: clock-usb-phy2-always-on-clk32k-8@688 {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
+		clock-output-names = "usb_phy2_always_on_clk32k";
 		clocks = <&sys_32k_ck>;
 		ti,bit-shift = <8>;
 		reg = <0x0688>;
 	};
 
-	usb_phy3_always_on_clk32k: usb_phy3_always_on_clk32k@698 {
+	usb_phy3_always_on_clk32k: clock-usb-phy3-always-on-clk32k-8@698 {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
+		clock-output-names = "usb_phy3_always_on_clk32k";
 		clocks = <&sys_32k_ck>;
 		ti,bit-shift = <8>;
 		reg = <0x0698>;
 	};
 
-	gpu_core_gclk_mux: gpu_core_gclk_mux@1220 {
+	gpu_core_gclk_mux: clock-gpu-core-gclk-mux-24@1220 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "gpu_core_gclk_mux";
 		clocks = <&dpll_core_h14x2_ck>, <&dpll_per_h14x2_ck>, <&dpll_gpu_m2_ck>;
 		ti,bit-shift = <24>;
 		reg = <0x1220>;
@@ -1419,9 +1591,10 @@
 		assigned-clock-parents = <&dpll_gpu_m2_ck>;
 	};
 
-	gpu_hyd_gclk_mux: gpu_hyd_gclk_mux@1220 {
+	gpu_hyd_gclk_mux: clock-gpu-hyd-gclk-mux-26@1220 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "gpu_hyd_gclk_mux";
 		clocks = <&dpll_core_h14x2_ck>, <&dpll_per_h14x2_ck>, <&dpll_gpu_m2_ck>;
 		ti,bit-shift = <26>;
 		reg = <0x1220>;
@@ -1429,34 +1602,38 @@
 		assigned-clock-parents = <&dpll_gpu_m2_ck>;
 	};
 
-	l3instr_ts_gclk_div: l3instr_ts_gclk_div@e50 {
+	l3instr_ts_gclk_div: clock-l3instr-ts-gclk-div-24@e50 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "l3instr_ts_gclk_div";
 		clocks = <&wkupaon_iclk_mux>;
 		ti,bit-shift = <24>;
 		reg = <0x0e50>;
 		ti,dividers = <8>, <16>, <32>;
 	};
 
-	vip1_gclk_mux: vip1_gclk_mux@1020 {
+	vip1_gclk_mux: clock-vip1-gclk-mux-24@1020 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "vip1_gclk_mux";
 		clocks = <&l3_iclk_div>, <&dpll_core_h23x2_ck>;
 		ti,bit-shift = <24>;
 		reg = <0x1020>;
 	};
 
-	vip2_gclk_mux: vip2_gclk_mux@1028 {
+	vip2_gclk_mux: clock-vip2-gclk-mux-24@1028 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "vip2_gclk_mux";
 		clocks = <&l3_iclk_div>, <&dpll_core_h23x2_ck>;
 		ti,bit-shift = <24>;
 		reg = <0x1028>;
 	};
 
-	vip3_gclk_mux: vip3_gclk_mux@1030 {
+	vip3_gclk_mux: clock-vip3-gclk-mux-24@1030 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "vip3_gclk_mux";
 		clocks = <&l3_iclk_div>, <&dpll_core_h23x2_ck>;
 		ti,bit-shift = <24>;
 		reg = <0x1030>;
@@ -1464,48 +1641,54 @@
 };
 
 &cm_core_clockdomains {
-	coreaon_clkdm: coreaon_clkdm {
+	coreaon_clkdm: clock-coreaon-clkdm {
 		compatible = "ti,clockdomain";
+		clock-output-names = "coreaon_clkdm";
 		clocks = <&dpll_usb_ck>;
 	};
 };
 
 &scm_conf_clocks {
-	dss_deshdcp_clk: dss_deshdcp_clk@558 {
+	dss_deshdcp_clk: clock-dss-deshdcp-0@558 {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
+		clock-output-names = "dss_deshdcp_clk";
 		clocks = <&l3_iclk_div>;
 		ti,bit-shift = <0>;
 		reg = <0x558>;
 	};
 
-       ehrpwm0_tbclk: ehrpwm0_tbclk@558 {
+       ehrpwm0_tbclk: clock-ehrpwm0-tbclk-20@558 {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
+		clock-output-names = "ehrpwm0_tbclk";
 		clocks = <&l4_root_clk_div>;
 		ti,bit-shift = <20>;
 		reg = <0x0558>;
 	};
 
-	ehrpwm1_tbclk: ehrpwm1_tbclk@558 {
+	ehrpwm1_tbclk: clock-ehrpwm1-tbclk-21@558 {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
+		clock-output-names = "ehrpwm1_tbclk";
 		clocks = <&l4_root_clk_div>;
 		ti,bit-shift = <21>;
 		reg = <0x0558>;
 	};
 
-	ehrpwm2_tbclk: ehrpwm2_tbclk@558 {
+	ehrpwm2_tbclk: clock-ehrpwm2-tbclk-22@558 {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
+		clock-output-names = "ehrpwm2_tbclk";
 		clocks = <&l4_root_clk_div>;
 		ti,bit-shift = <22>;
 		reg = <0x0558>;
 	};
 
-	sys_32k_ck: sys_32k_ck {
+	sys_32k_ck: clock-sys-32k {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "sys_32k_ck";
 		clocks = <&sys_clk32_crystal_ck>, <&sys_clk32_pseudo_ck>, <&sys_clk32_pseudo_ck>, <&sys_clk32_pseudo_ck>;
 		ti,bit-shift = <8>;
 		reg = <0x6c4>;
@@ -1513,97 +1696,110 @@
 };
 
 &cm_core_aon {
-	mpu_cm: mpu-cm@300 {
+	mpu_cm: clock@300 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "mpu_cm";
 		reg = <0x300 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0 0x300 0x100>;
 
-		mpu_clkctrl: mpu-clkctrl@20 {
+		mpu_clkctrl: clock@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "mpu_clkctrl";
 			reg = <0x20 0x4>;
 			#clock-cells = <2>;
 		};
 
 	};
 
-	dsp1_cm: dsp1-cm@400 {
+	dsp1_cm: clock@400 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "dsp1_cm";
 		reg = <0x400 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0 0x400 0x100>;
 
-		dsp1_clkctrl: dsp1-clkctrl@20 {
+		dsp1_clkctrl: clock@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "dsp1_clkctrl";
 			reg = <0x20 0x4>;
 			#clock-cells = <2>;
 		};
 
 	};
 
-	ipu_cm: ipu-cm@500 {
+	ipu_cm: clock@500 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "ipu_cm";
 		reg = <0x500 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0 0x500 0x100>;
 
-		ipu1_clkctrl: ipu1-clkctrl@20 {
+		ipu1_clkctrl: clock@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "ipu1_clkctrl";
 			reg = <0x20 0x4>;
 			#clock-cells = <2>;
 			assigned-clocks = <&ipu1_clkctrl DRA7_IPU1_MMU_IPU1_CLKCTRL 24>;
 			assigned-clock-parents = <&dpll_core_h22x2_ck>;
 		};
 
-		ipu_clkctrl: ipu-clkctrl@50 {
+		ipu_clkctrl: clock@50 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "ipu_clkctrl";
 			reg = <0x50 0x34>;
 			#clock-cells = <2>;
 		};
 
 	};
 
-	dsp2_cm: dsp2-cm@600 {
+	dsp2_cm: clock@600 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "dsp2_cm";
 		reg = <0x600 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0 0x600 0x100>;
 
-		dsp2_clkctrl: dsp2-clkctrl@20 {
+		dsp2_clkctrl: clock@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "dsp2_clkctrl";
 			reg = <0x20 0x4>;
 			#clock-cells = <2>;
 		};
 
 	};
 
-	rtc_cm: rtc-cm@700 {
+	rtc_cm: clock@700 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "rtc_cm";
 		reg = <0x700 0x60>;
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0 0x700 0x60>;
 
-		rtc_clkctrl: rtc-clkctrl@20 {
+		rtc_clkctrl: clock@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "rtc_clkctrl";
 			reg = <0x20 0x28>;
 			#clock-cells = <2>;
 		};
 	};
 
-	vpe_cm: vpe-cm@760 {
+	vpe_cm: clock@760 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "vpe_cm";
 		reg = <0x760 0xc>;
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0 0x760 0xc>;
 
-		vpe_clkctrl: vpe-clkctrl@0 {
+		vpe_clkctrl: clock@0 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "vpe_clkctrl";
 			reg = <0x0 0xc>;
 			#clock-cells = <2>;
 		};
@@ -1612,212 +1808,242 @@
 };
 
 &cm_core {
-	coreaon_cm: coreaon-cm@600 {
+	coreaon_cm: clock@600 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "coreaon_cm";
 		reg = <0x600 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0 0x600 0x100>;
 
-		coreaon_clkctrl: coreaon-clkctrl@20 {
+		coreaon_clkctrl: clock@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "coreaon_clkctrl";
 			reg = <0x20 0x1c>;
 			#clock-cells = <2>;
 		};
 	};
 
-	l3main1_cm: l3main1-cm@700 {
+	l3main1_cm: clock@700 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "l3main1_cm";
 		reg = <0x700 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0 0x700 0x100>;
 
-		l3main1_clkctrl: l3main1-clkctrl@20 {
+		l3main1_clkctrl: clock@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "l3main1_clkctrl";
 			reg = <0x20 0x74>;
 			#clock-cells = <2>;
 		};
 
 	};
 
-	ipu2_cm: ipu2-cm@900 {
+	ipu2_cm: clock@900 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "ipu2_cm";
 		reg = <0x900 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0 0x900 0x100>;
 
-		ipu2_clkctrl: ipu2-clkctrl@20 {
+		ipu2_clkctrl: clock@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "ipu2_clkctrl";
 			reg = <0x20 0x4>;
 			#clock-cells = <2>;
 		};
 
 	};
 
-	dma_cm: dma-cm@a00 {
+	dma_cm: clock@a00 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "dma_cm";
 		reg = <0xa00 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0 0xa00 0x100>;
 
-		dma_clkctrl: dma-clkctrl@20 {
+		dma_clkctrl: clock@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "dma_clkctrl";
 			reg = <0x20 0x4>;
 			#clock-cells = <2>;
 		};
 	};
 
-	emif_cm: emif-cm@b00 {
+	emif_cm: clock@b00 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "emif_cm";
 		reg = <0xb00 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0 0xb00 0x100>;
 
-		emif_clkctrl: emif-clkctrl@20 {
+		emif_clkctrl: clock@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "emif_clkctrl";
 			reg = <0x20 0x4>;
 			#clock-cells = <2>;
 		};
 	};
 
-	atl_cm: atl-cm@c00 {
+	atl_cm: clock@c00 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "atl_cm";
 		reg = <0xc00 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0 0xc00 0x100>;
 
-		atl_clkctrl: atl-clkctrl@0 {
+		atl_clkctrl: clock@0 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "atl_clkctrl";
 			reg = <0x0 0x4>;
 			#clock-cells = <2>;
 		};
 	};
 
-	l4cfg_cm: l4cfg-cm@d00 {
+	l4cfg_cm: clock@d00 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "l4cfg_cm";
 		reg = <0xd00 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0 0xd00 0x100>;
 
-		l4cfg_clkctrl: l4cfg-clkctrl@20 {
+		l4cfg_clkctrl: clock@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "l4cfg_clkctrl";
 			reg = <0x20 0x84>;
 			#clock-cells = <2>;
 		};
 	};
 
-	l3instr_cm: l3instr-cm@e00 {
+	l3instr_cm: clock@e00 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "l3instr_cm";
 		reg = <0xe00 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0 0xe00 0x100>;
 
-		l3instr_clkctrl: l3instr-clkctrl@20 {
+		l3instr_clkctrl: clock@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "l3instr_clkctrl";
 			reg = <0x20 0xc>;
 			#clock-cells = <2>;
 		};
 	};
 
-	iva_cm: iva-cm@f00 {
+	iva_cm: clock@f00 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "iva_cm";
 		reg = <0xf00 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0 0xf00 0x100>;
 
-		iva_clkctrl: iva-clkctrl@20 {
+		iva_clkctrl: clock@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "iva_clkctrl";
 			reg = <0x20 0xc>;
 			#clock-cells = <2>;
 		};
 	};
 
-	cam_cm: cam-cm@1000 {
+	cam_cm: clock@1000 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "cam_cm";
 		reg = <0x1000 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0 0x1000 0x100>;
 
-		cam_clkctrl: cam-clkctrl@20 {
+		cam_clkctrl: clock@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "cam_clkctrl";
 			reg = <0x20 0x2c>;
 			#clock-cells = <2>;
 		};
 	};
 
-	dss_cm: dss-cm@1100 {
+	dss_cm: clock@1100 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "dss_cm";
 		reg = <0x1100 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0 0x1100 0x100>;
 
-		dss_clkctrl: dss-clkctrl@20 {
+		dss_clkctrl: clock@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "dss_clkctrl";
 			reg = <0x20 0x14>;
 			#clock-cells = <2>;
 		};
 	};
 
-	gpu_cm: gpu-cm@1200 {
+	gpu_cm: clock@1200 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "gpu_cm";
 		reg = <0x1200 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0 0x1200 0x100>;
 
-		gpu_clkctrl: gpu-clkctrl@20 {
+		gpu_clkctrl: clock@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "gpu_clkctrl";
 			reg = <0x20 0x4>;
 			#clock-cells = <2>;
 		};
 	};
 
-	l3init_cm: l3init-cm@1300 {
+	l3init_cm: clock@1300 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "l3init_cm";
 		reg = <0x1300 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0 0x1300 0x100>;
 
-		l3init_clkctrl: l3init-clkctrl@20 {
+		l3init_clkctrl: clock@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "l3init_clkctrl";
 			reg = <0x20 0x6c>, <0xe0 0x14>;
 			#clock-cells = <2>;
 		};
 
-		pcie_clkctrl: pcie-clkctrl@b0 {
+		pcie_clkctrl: clock@b0 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "pcie_clkctrl";
 			reg = <0xb0 0xc>;
 			#clock-cells = <2>;
 		};
 
-		gmac_clkctrl: gmac-clkctrl@d0 {
+		gmac_clkctrl: clock@d0 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "gmac_clkctrl";
 			reg = <0xd0 0x4>;
 			#clock-cells = <2>;
 		};
 
 	};
 
-	l4per_cm: l4per-cm@1700 {
+	l4per_cm: clock@1700 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "l4per_cm";
 		reg = <0x1700 0x300>;
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0 0x1700 0x300>;
 
-		l4per_clkctrl: l4per-clkctrl@28 {
+		l4per_clkctrl: clock@28 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "l4per_clkctrl";
 			reg = <0x28 0x64>, <0xa0 0x24>, <0xf0 0x3c>, <0x140 0x1c>, <0x170 0x4>;
 			#clock-cells = <2>;
 
@@ -1825,20 +2051,23 @@
 			assigned-clock-parents = <&abe_24m_fclk>;
 		};
 
-		l4sec_clkctrl: l4sec-clkctrl@1a0 {
+		l4sec_clkctrl: clock@1a0 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "l4sec_clkctrl";
 			reg = <0x1a0 0x2c>;
 			#clock-cells = <2>;
 		};
 
-		l4per2_clkctrl: l4per2-clkctrl@c {
+		l4per2_clkctrl: clock@c {
 			compatible = "ti,clkctrl";
+			clock-output-names = "l4per2_clkctrl";
 			reg = <0xc 0x4>, <0x18 0xc>, <0x90 0xc>, <0xc4 0x4>, <0x138 0x4>, <0x160 0xc>, <0x178 0x24>, <0x1d0 0x3c>;
 			#clock-cells = <2>;
 		};
 
-		l4per3_clkctrl: l4per3-clkctrl@14 {
+		l4per3_clkctrl: clock@14 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "l4per3_clkctrl";
 			reg = <0x14 0x4>, <0xc8 0x14>, <0x130 0x4>;
 			#clock-cells = <2>;
 		};
@@ -1847,15 +2076,17 @@
 };
 
 &prm {
-	wkupaon_cm: wkupaon-cm@1800 {
+	wkupaon_cm: clock@1800 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "wkupaon_cm";
 		reg = <0x1800 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0 0x1800 0x100>;
 
-		wkupaon_clkctrl: wkupaon-clkctrl@20 {
+		wkupaon_clkctrl: clock@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "wkupaon_clkctrl";
 			reg = <0x20 0x6c>;
 			#clock-cells = <2>;
 		};
diff --git a/arch/arm/boot/dts/e60k02.dtsi b/arch/arm/boot/dts/e60k02.dtsi
index 1a49f15f2df2..935e2359f8df 100644
--- a/arch/arm/boot/dts/e60k02.dtsi
+++ b/arch/arm/boot/dts/e60k02.dtsi
@@ -22,14 +22,14 @@
 	gpio_keys: gpio-keys {
 		compatible = "gpio-keys";
 
-		power {
+		key-power {
 			label = "Power";
 			gpios = <&gpio5 8 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
 			wakeup-source;
 		};
 
-		cover {
+		key-cover {
 			label = "Cover";
 			gpios = <&gpio5 12 GPIO_ACTIVE_LOW>;
 			linux,code = <SW_LID>;
diff --git a/arch/arm/boot/dts/e70k02.dtsi b/arch/arm/boot/dts/e70k02.dtsi
index 156de653f2cd..27ef9a62b23c 100644
--- a/arch/arm/boot/dts/e70k02.dtsi
+++ b/arch/arm/boot/dts/e70k02.dtsi
@@ -26,14 +26,14 @@
 	gpio_keys: gpio-keys {
 		compatible = "gpio-keys";
 
-		power {
+		key-power {
 			label = "Power";
 			gpios = <&gpio4 25 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
 			wakeup-source;
 		};
 
-		cover {
+		key-cover {
 			label = "Cover";
 			gpios = <&gpio4 23 GPIO_ACTIVE_LOW>;
 			linux,code = <SW_LID>;
@@ -41,13 +41,13 @@
 			wakeup-source;
 		};
 
-		pageup {
+		key-pageup {
 			label = "PageUp";
 			gpios = <&gpio4 0 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_PAGEUP>;
 		};
 
-		pagedown {
+		key-pagedown {
 			label = "PageDown";
 			gpios = <&gpio4 2 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_PAGEDOWN>;
diff --git a/arch/arm/boot/dts/ecx-common.dtsi b/arch/arm/boot/dts/ecx-common.dtsi
index 57a028a69373..ce5221c6b358 100644
--- a/arch/arm/boot/dts/ecx-common.dtsi
+++ b/arch/arm/boot/dts/ecx-common.dtsi
@@ -9,11 +9,11 @@
 	};
 
 	psci {
-		compatible	= "arm,psci";
-		method		= "smc";
-		cpu_suspend	= <0x84000002>;
-		cpu_off		= <0x84000004>;
-		cpu_on		= <0x84000006>;
+		compatible = "arm,psci";
+		method = "smc";
+		cpu_suspend = <0x84000002>;
+		cpu_off = <0x84000004>;
+		cpu_on = <0x84000006>;
 	};
 
 	soc {
diff --git a/arch/arm/boot/dts/elpida_ecb240abacn.dtsi b/arch/arm/boot/dts/elpida_ecb240abacn.dtsi
index d87ee4794f83..9698801cbcfb 100644
--- a/arch/arm/boot/dts/elpida_ecb240abacn.dtsi
+++ b/arch/arm/boot/dts/elpida_ecb240abacn.dtsi
@@ -5,7 +5,7 @@
 
 / {
 	elpida_ECB240ABACN: lpddr2 {
-		compatible	= "Elpida,ECB240ABACN","jedec,lpddr2-s4";
+		compatible	= "elpida,ECB240ABACN","jedec,lpddr2-s4";
 		density		= <2048>;
 		io-width	= <32>;
 
diff --git a/arch/arm/boot/dts/en7523-evb.dts b/arch/arm/boot/dts/en7523-evb.dts
new file mode 100644
index 000000000000..f23a25cce119
--- /dev/null
+++ b/arch/arm/boot/dts/en7523-evb.dts
@@ -0,0 +1,43 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+/dts-v1/;
+
+/* Bootloader installs ATF here */
+/memreserve/ 0x80000000 0x200000;
+
+#include "en7523.dtsi"
+
+/ {
+	model = "Airoha EN7523 Evaluation Board";
+	compatible = "airoha,en7523-evb", "airoha,en7523";
+
+	aliases {
+		serial0 = &uart1;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200 earlycon";
+		stdout-path = "serial0:115200n8";
+		linux,usable-memory-range = <0x80200000 0x1fe00000>;
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x20000000>;
+	};
+};
+
+&gpio0 {
+	status = "okay";
+};
+
+&gpio1 {
+	status = "okay";
+};
+
+&pcie0 {
+	status = "okay";
+};
+
+&pcie1 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/en7523.dtsi b/arch/arm/boot/dts/en7523.dtsi
new file mode 100644
index 000000000000..7f839331a777
--- /dev/null
+++ b/arch/arm/boot/dts/en7523.dtsi
@@ -0,0 +1,204 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/clock/en7523-clk.h>
+
+/ {
+	interrupt-parent = <&gic>;
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		npu_binary@84000000 {
+			no-map;
+			reg = <0x84000000 0xA00000>;
+		};
+
+		npu_flag@84B0000 {
+			no-map;
+			reg = <0x84B00000 0x100000>;
+		};
+
+		npu_pkt@85000000 {
+			no-map;
+			reg = <0x85000000 0x1A00000>;
+		};
+
+		npu_phyaddr@86B00000 {
+			no-map;
+			reg = <0x86B00000 0x100000>;
+		};
+
+		npu_rxdesc@86D00000 {
+			no-map;
+			reg = <0x86D00000 0x100000>;
+		};
+	};
+
+	psci {
+		compatible = "arm,psci-0.2";
+		method = "smc";
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu-map {
+			cluster0 {
+				core0 {
+					cpu = <&cpu0>;
+				};
+				core1 {
+					cpu = <&cpu1>;
+				};
+			};
+		};
+
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0x0>;
+			enable-method = "psci";
+			clock-frequency = <80000000>;
+			next-level-cache = <&L2_0>;
+		};
+
+		cpu1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0x1>;
+			enable-method = "psci";
+			clock-frequency = <80000000>;
+			next-level-cache = <&L2_0>;
+		};
+
+		L2_0: l2-cache0 {
+			compatible = "cache";
+		};
+	};
+
+	scu: system-controller@1fa20000 {
+		compatible = "airoha,en7523-scu";
+		reg = <0x1fa20000 0x400>,
+		      <0x1fb00000 0x1000>;
+		#clock-cells = <1>;
+	};
+
+	gic: interrupt-controller@9000000 {
+		compatible = "arm,gic-v3";
+		interrupt-controller;
+		#interrupt-cells = <3>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0x09000000 0x20000>,
+		      <0x09080000 0x80000>,
+		      <0x09400000 0x2000>,
+		      <0x09500000 0x2000>,
+		      <0x09600000 0x20000>;
+		interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_LOW>;
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupt-parent = <&gic>;
+		interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW>,
+			     <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW>,
+			     <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW>,
+			     <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW>;
+	};
+
+	uart1: serial@1fbf0000 {
+		compatible = "ns16550";
+		reg = <0x1fbf0000 0x30>;
+		reg-io-width = <4>;
+		reg-shift = <2>;
+		interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>;
+		clock-frequency = <1843200>;
+		status = "okay";
+	};
+
+	gpio0: gpio@1fbf0200 {
+		compatible = "airoha,en7523-gpio";
+		reg = <0x1fbf0204 0x4>,
+		      <0x1fbf0200 0x4>,
+		      <0x1fbf0220 0x4>,
+		      <0x1fbf0214 0x4>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	gpio1: gpio@1fbf0270 {
+		compatible = "airoha,en7523-gpio";
+		reg = <0x1fbf0270 0x4>,
+		      <0x1fbf0260 0x4>,
+		      <0x1fbf0264 0x4>,
+		      <0x1fbf0278 0x4>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	pcie0: pcie@1fa91000 {
+		compatible = "airoha,en7523-pcie", "mediatek,mt7622-pcie";
+		device_type = "pci";
+		reg = <0x1fa91000 0x1000>;
+		reg-names = "port0";
+		linux,pci-domain = <0>;
+		#address-cells = <3>;
+		#size-cells = <2>;
+		interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "pcie_irq";
+		clocks = <&scu EN7523_CLK_PCIE>;
+		clock-names = "sys_ck0";
+		bus-range = <0x00 0xff>;
+		ranges = <0x82000000 0 0x20000000  0x20000000  0 0x8000000>;
+		status = "disabled";
+
+		#interrupt-cells = <1>;
+		interrupt-map-mask = <0 0 0 7>;
+		interrupt-map = <0 0 0 1 &pcie_intc0 0>,
+				<0 0 0 2 &pcie_intc0 1>,
+				<0 0 0 3 &pcie_intc0 2>,
+				<0 0 0 4 &pcie_intc0 3>;
+		pcie_intc0: interrupt-controller {
+			interrupt-controller;
+			#address-cells = <0>;
+			#interrupt-cells = <1>;
+		};
+	};
+
+	pcie1: pcie@1fa92000 {
+		compatible = "airoha,en7523-pcie", "mediatek,mt7622-pcie";
+		device_type = "pci";
+		reg = <0x1fa92000 0x1000>;
+		reg-names = "port1";
+		linux,pci-domain = <1>;
+		#address-cells = <3>;
+		#size-cells = <2>;
+		interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "pcie_irq";
+		clocks = <&scu EN7523_CLK_PCIE>;
+		clock-names = "sys_ck1";
+		bus-range = <0x00 0xff>;
+		ranges = <0x82000000 0 0x28000000  0x28000000  0 0x8000000>;
+		status = "disabled";
+
+		#interrupt-cells = <1>;
+		interrupt-map-mask = <0 0 0 7>;
+		interrupt-map = <0 0 0 1 &pcie_intc1 0>,
+				<0 0 0 2 &pcie_intc1 1>,
+				<0 0 0 3 &pcie_intc1 2>,
+				<0 0 0 4 &pcie_intc1 3>;
+		pcie_intc1: interrupt-controller {
+			interrupt-controller;
+			#address-cells = <0>;
+			#interrupt-cells = <1>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/exynos-pinctrl.h b/arch/arm/boot/dts/exynos-pinctrl.h
new file mode 100644
index 000000000000..e3a6df95281c
--- /dev/null
+++ b/arch/arm/boot/dts/exynos-pinctrl.h
@@ -0,0 +1,55 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Samsung Exynos DTS pinctrl constants
+ *
+ * Copyright (c) 2016 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
+ * Copyright (c) 2022 Linaro Ltd
+ * Author: Krzysztof Kozlowski <krzk@kernel.org>
+ */
+
+#ifndef __DTS_ARM_SAMSUNG_EXYNOS_PINCTRL_H__
+#define __DTS_ARM_SAMSUNG_EXYNOS_PINCTRL_H__
+
+#define EXYNOS_PIN_PULL_NONE		0
+#define EXYNOS_PIN_PULL_DOWN		1
+#define EXYNOS_PIN_PULL_UP		3
+
+/* Pin function in power down mode */
+#define EXYNOS_PIN_PDN_OUT0		0
+#define EXYNOS_PIN_PDN_OUT1		1
+#define EXYNOS_PIN_PDN_INPUT		2
+#define EXYNOS_PIN_PDN_PREV		3
+
+/* Drive strengths for Exynos3250, Exynos4 (all) and Exynos5250 */
+#define EXYNOS4_PIN_DRV_LV1		0
+#define EXYNOS4_PIN_DRV_LV2		2
+#define EXYNOS4_PIN_DRV_LV3		1
+#define EXYNOS4_PIN_DRV_LV4		3
+
+/* Drive strengths for Exynos5260 */
+#define EXYNOS5260_PIN_DRV_LV1		0
+#define EXYNOS5260_PIN_DRV_LV2		1
+#define EXYNOS5260_PIN_DRV_LV4		2
+#define EXYNOS5260_PIN_DRV_LV6		3
+
+/*
+ * Drive strengths for Exynos5410, Exynos542x, Exynos5800 and Exynos850 (except
+ * GPIO_HSI block)
+ */
+#define EXYNOS5420_PIN_DRV_LV1		0
+#define EXYNOS5420_PIN_DRV_LV2		1
+#define EXYNOS5420_PIN_DRV_LV3		2
+#define EXYNOS5420_PIN_DRV_LV4		3
+
+#define EXYNOS_PIN_FUNC_INPUT		0
+#define EXYNOS_PIN_FUNC_OUTPUT		1
+#define EXYNOS_PIN_FUNC_2		2
+#define EXYNOS_PIN_FUNC_3		3
+#define EXYNOS_PIN_FUNC_4		4
+#define EXYNOS_PIN_FUNC_5		5
+#define EXYNOS_PIN_FUNC_6		6
+#define EXYNOS_PIN_FUNC_EINT		0xf
+#define EXYNOS_PIN_FUNC_F		EXYNOS_PIN_FUNC_EINT
+
+#endif /* __DTS_ARM_SAMSUNG_EXYNOS_PINCTRL_H__ */
diff --git a/arch/arm/boot/dts/exynos3250-artik5.dtsi b/arch/arm/boot/dts/exynos3250-artik5.dtsi
index 829c05b2c405..0ac3f284fbb8 100644
--- a/arch/arm/boot/dts/exynos3250-artik5.dtsi
+++ b/arch/arm/boot/dts/exynos3250-artik5.dtsi
@@ -356,15 +356,15 @@
 };
 
 &pinctrl_1 {
-	bten: bten {
-		samsung,pins ="gpx1-7";
+	bten: bten-pins {
+		samsung,pins = "gpx1-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
 		samsung,pin-con-pdn = <EXYNOS_PIN_PDN_PREV>;
 		samsung,pin-pud-pdn = <EXYNOS_PIN_PULL_DOWN>;
 	};
 
-	wlanen: wlanen {
+	wlanen: wlanen-pins {
 		samsung,pins = "gpx2-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
@@ -372,12 +372,12 @@
 		samsung,pin-val = <1>;
 	};
 
-	s2mps14_irq: s2mps14-irq {
+	s2mps14_irq: s2mps14-irq-pins {
 		samsung,pins = "gpx3-5";
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 	};
 
-	bthostwake: bthostwake {
+	bthostwake: bthostwake-pins {
 		samsung,pins = "gpx3-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
@@ -385,7 +385,7 @@
 		samsung,pin-pud-pdn = <EXYNOS_PIN_PULL_NONE>;
 	};
 
-	btwake: btwake {
+	btwake: btwake-pins {
 		samsung,pins = "gpx3-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
diff --git a/arch/arm/boot/dts/exynos3250-monk.dts b/arch/arm/boot/dts/exynos3250-monk.dts
index 8b41a9d5e2db..02a9dc479d34 100644
--- a/arch/arm/boot/dts/exynos3250-monk.dts
+++ b/arch/arm/boot/dts/exynos3250-monk.dts
@@ -69,7 +69,7 @@
 			reg = <0x25>;
 			wakeup-source;
 
-			muic: max77836-muic {
+			extcon {
 				compatible = "maxim,max77836-muic";
 			};
 
diff --git a/arch/arm/boot/dts/exynos3250-pinctrl.dtsi b/arch/arm/boot/dts/exynos3250-pinctrl.dtsi
index dff3c6e3aa1f..011ba2eff29e 100644
--- a/arch/arm/boot/dts/exynos3250-pinctrl.dtsi
+++ b/arch/arm/boot/dts/exynos3250-pinctrl.dtsi
@@ -9,50 +9,25 @@
  * tree nodes are listed in this file.
  */
 
-#include <dt-bindings/pinctrl/samsung.h>
+#include "exynos-pinctrl.h"
 
 #define PIN_IN(_pin, _pull, _drv)					\
-	_pin {								\
+	pin- ## _pin {							\
 		samsung,pins = #_pin;					\
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;		\
 		samsung,pin-pud = <EXYNOS_PIN_PULL_ ##_pull>;		\
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_ ##_drv>;		\
 	}
 
-#define PIN_OUT(_pin, _drv)						\
-	_pin {								\
-		samsung,pins = #_pin;					\
-		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;	\
-		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;		\
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_ ##_drv>;		\
-	}
-
-#define PIN_OUT_SET(_pin, _val, _drv)					\
-	_pin {								\
-		samsung,pins = #_pin;					\
-		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;	\
-		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;		\
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_ ##_drv>;		\
-		samsung,pin-val = <_val>;				\
-	}
-
-#define PIN_CFG(_pin, _sel, _pull, _drv)				\
-	_pin {								\
-		samsung,pins = #_pin;					\
-		samsung,pin-function = <_sel>;				\
-		samsung,pin-pud = <EXYNOS_PIN_PULL_ ##_pull>;		\
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_ ##_drv>;		\
-	}
-
 #define PIN_SLP(_pin, _mode, _pull)					\
-	_pin {								\
+	pin- ## _pin {							\
 		samsung,pins = #_pin;					\
 		samsung,pin-con-pdn = <EXYNOS_PIN_PDN_ ##_mode>;	\
 		samsung,pin-pud-pdn = <EXYNOS_PIN_PULL_ ##_pull>;	\
 	}
 
 &pinctrl_0 {
-	gpa0: gpa0 {
+	gpa0: gpa0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -60,7 +35,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpa1: gpa1 {
+	gpa1: gpa1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -68,7 +43,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpb: gpb {
+	gpb: gpb-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -76,7 +51,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpc0: gpc0 {
+	gpc0: gpc0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -84,7 +59,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpc1: gpc1 {
+	gpc1: gpc1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -92,7 +67,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpd0: gpd0 {
+	gpd0: gpd0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -100,7 +75,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpd1: gpd1 {
+	gpd1: gpd1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -108,84 +83,84 @@
 		#interrupt-cells = <2>;
 	};
 
-	uart0_data: uart0-data {
+	uart0_data: uart0-data-pins {
 		samsung,pins = "gpa0-0", "gpa0-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	uart0_fctl: uart0-fctl {
+	uart0_fctl: uart0-fctl-pins {
 		samsung,pins = "gpa0-2", "gpa0-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	uart1_data: uart1-data {
+	uart1_data: uart1-data-pins {
 		samsung,pins = "gpa0-4", "gpa0-5";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	uart1_fctl: uart1-fctl {
+	uart1_fctl: uart1-fctl-pins {
 		samsung,pins = "gpa0-6", "gpa0-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2c2_bus: i2c2-bus {
+	i2c2_bus: i2c2-bus-pins {
 		samsung,pins = "gpa0-6", "gpa0-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	uart2_data: uart2-data {
+	uart2_data: uart2-data-pins {
 		samsung,pins = "gpa1-0", "gpa1-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2c3_bus: i2c3-bus {
+	i2c3_bus: i2c3-bus-pins {
 		samsung,pins = "gpa1-2", "gpa1-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	spi0_bus: spi0-bus {
+	spi0_bus: spi0-bus-pins {
 		samsung,pins = "gpb-0", "gpb-2", "gpb-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2c4_bus: i2c4-bus {
+	i2c4_bus: i2c4-bus-pins {
 		samsung,pins = "gpb-0", "gpb-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	spi1_bus: spi1-bus {
+	spi1_bus: spi1-bus-pins {
 		samsung,pins = "gpb-4", "gpb-6", "gpb-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2c5_bus: i2c5-bus {
+	i2c5_bus: i2c5-bus-pins {
 		samsung,pins = "gpb-2", "gpb-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2s2_bus: i2s2-bus {
+	i2s2_bus: i2s2-bus-pins {
 		samsung,pins = "gpc1-0", "gpc1-1", "gpc1-2", "gpc1-3",
 				"gpc1-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
@@ -193,7 +168,7 @@
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	pcm2_bus: pcm2-bus {
+	pcm2_bus: pcm2-bus-pins {
 		samsung,pins = "gpc1-0", "gpc1-1", "gpc1-2", "gpc1-3",
 				"gpc1-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
@@ -201,63 +176,63 @@
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2c6_bus: i2c6-bus {
+	i2c6_bus: i2c6-bus-pins {
 		samsung,pins = "gpc1-3", "gpc1-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	pwm0_out: pwm0-out {
+	pwm0_out: pwm0-out-pins {
 		samsung,pins = "gpd0-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	pwm1_out: pwm1-out {
+	pwm1_out: pwm1-out-pins {
 		samsung,pins = "gpd0-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2c7_bus: i2c7-bus {
+	i2c7_bus: i2c7-bus-pins {
 		samsung,pins = "gpd0-2", "gpd0-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	pwm2_out: pwm2-out {
+	pwm2_out: pwm2-out-pins {
 		samsung,pins = "gpd0-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	pwm3_out: pwm3-out {
+	pwm3_out: pwm3-out-pins {
 		samsung,pins = "gpd0-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2c0_bus: i2c0-bus {
+	i2c0_bus: i2c0-bus-pins {
 		samsung,pins = "gpd1-0", "gpd1-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	mipi0_clk: mipi0-clk {
+	mipi0_clk: mipi0-clk-pins {
 		samsung,pins = "gpd1-0", "gpd1-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2c1_bus: i2c1-bus {
+	i2c1_bus: i2c1-bus-pins {
 		samsung,pins = "gpd1-2", "gpd1-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
@@ -266,22 +241,22 @@
 };
 
 &pinctrl_1 {
-	gpe0: gpe0 {
+	gpe0: gpe0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpe1: gpe1 {
+	gpe1: gpe1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpe2: gpe2 {
+	gpe2: gpe2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpk0: gpk0 {
+	gpk0: gpk0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -289,7 +264,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpk1: gpk1 {
+	gpk1: gpk1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -297,7 +272,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpk2: gpk2 {
+	gpk2: gpk2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -305,7 +280,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpl0: gpl0 {
+	gpl0: gpl0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -313,7 +288,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpm0: gpm0 {
+	gpm0: gpm0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -321,7 +296,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpm1: gpm1 {
+	gpm1: gpm1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -329,7 +304,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpm2: gpm2 {
+	gpm2: gpm2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -337,7 +312,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpm3: gpm3 {
+	gpm3: gpm3-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -345,7 +320,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpm4: gpm4 {
+	gpm4: gpm4-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -353,7 +328,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpx0: gpx0 {
+	gpx0: gpx0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -370,7 +345,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpx1: gpx1 {
+	gpx1: gpx1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -387,7 +362,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpx2: gpx2 {
+	gpx2: gpx2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -395,7 +370,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpx3: gpx3 {
+	gpx3: gpx3-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -403,126 +378,126 @@
 		#interrupt-cells = <2>;
 	};
 
-	sd0_clk: sd0-clk {
+	sd0_clk: sd0-clk-pins {
 		samsung,pins = "gpk0-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd0_cmd: sd0-cmd {
+	sd0_cmd: sd0-cmd-pins {
 		samsung,pins = "gpk0-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd0_cd: sd0-cd {
+	sd0_cd: sd0-cd-pins {
 		samsung,pins = "gpk0-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd0_rdqs: sd0-rdqs {
+	sd0_rdqs: sd0-rdqs-pins {
 		samsung,pins = "gpk0-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd0_bus1: sd0-bus-width1 {
+	sd0_bus1: sd0-bus-width1-pins {
 		samsung,pins = "gpk0-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd0_bus4: sd0-bus-width4 {
+	sd0_bus4: sd0-bus-width4-pins {
 		samsung,pins = "gpk0-4", "gpk0-5", "gpk0-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd0_bus8: sd0-bus-width8 {
+	sd0_bus8: sd0-bus-width8-pins {
 		samsung,pins = "gpl0-0", "gpl0-1", "gpl0-2", "gpl0-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd1_clk: sd1-clk {
+	sd1_clk: sd1-clk-pins {
 		samsung,pins = "gpk1-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd1_cmd: sd1-cmd {
+	sd1_cmd: sd1-cmd-pins {
 		samsung,pins = "gpk1-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd1_cd: sd1-cd {
+	sd1_cd: sd1-cd-pins {
 		samsung,pins = "gpk1-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd1_bus1: sd1-bus-width1 {
+	sd1_bus1: sd1-bus-width1-pins {
 		samsung,pins = "gpk1-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd1_bus4: sd1-bus-width4 {
+	sd1_bus4: sd1-bus-width4-pins {
 		samsung,pins = "gpk1-4", "gpk1-5", "gpk1-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd2_clk: sd2-clk {
+	sd2_clk: sd2-clk-pins {
 		samsung,pins = "gpk2-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd2_cmd: sd2-cmd {
+	sd2_cmd: sd2-cmd-pins {
 		samsung,pins = "gpk2-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd2_cd: sd2-cd {
+	sd2_cd: sd2-cd-pins {
 		samsung,pins = "gpk2-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd2_bus1: sd2-bus-width1 {
+	sd2_bus1: sd2-bus-width1-pins {
 		samsung,pins = "gpk2-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd2_bus4: sd2-bus-width4 {
+	sd2_bus4: sd2-bus-width4-pins {
 		samsung,pins = "gpk2-4", "gpk2-5", "gpk2-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	cam_port_b_io: cam-port-b-io {
+	cam_port_b_io: cam-port-b-io-pins {
 		samsung,pins = "gpm0-0", "gpm0-1", "gpm0-2", "gpm0-3",
 				"gpm0-4", "gpm0-5", "gpm0-6", "gpm0-7",
 				"gpm1-0", "gpm1-1", "gpm2-0", "gpm2-1";
@@ -531,35 +506,35 @@
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	cam_port_b_clk_active: cam-port-b-clk-active {
+	cam_port_b_clk_active: cam-port-b-clk-active-pins {
 		samsung,pins = "gpm2-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	cam_port_b_clk_idle: cam-port-b-clk-idle {
+	cam_port_b_clk_idle: cam-port-b-clk-idle-pins {
 		samsung,pins = "gpm2-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	fimc_is_i2c0: fimc-is-i2c0 {
+	fimc_is_i2c0: fimc-is-i2c0-pins {
 		samsung,pins = "gpm4-0", "gpm4-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	fimc_is_i2c1: fimc-is-i2c1 {
+	fimc_is_i2c1: fimc-is-i2c1-pins {
 		samsung,pins = "gpm4-2", "gpm4-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	fimc_is_uart: fimc-is-uart {
+	fimc_is_uart: fimc-is-uart-pins {
 		samsung,pins = "gpm3-5", "gpm3-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
diff --git a/arch/arm/boot/dts/exynos3250-rinato.dts b/arch/arm/boot/dts/exynos3250-rinato.dts
index 5f7f8fedfb92..6d2c7bb19184 100644
--- a/arch/arm/boot/dts/exynos3250-rinato.dts
+++ b/arch/arm/boot/dts/exynos3250-rinato.dts
@@ -70,7 +70,7 @@
 			reg = <0x25>;
 			wakeup-source;
 
-			muic: max77836-muic {
+			extcon {
 				compatible = "maxim,max77836-muic";
 			};
 
diff --git a/arch/arm/boot/dts/exynos3250.dtsi b/arch/arm/boot/dts/exynos3250.dtsi
index a10b789d8acf..326b9e0ed8d3 100644
--- a/arch/arm/boot/dts/exynos3250.dtsi
+++ b/arch/arm/boot/dts/exynos3250.dtsi
@@ -269,7 +269,8 @@
 		};
 
 		timer@10050000 {
-			compatible = "samsung,exynos4210-mct";
+			compatible = "samsung,exynos3250-mct",
+				     "samsung,exynos4210-mct";
 			reg = <0x10050000 0x800>;
 			interrupts = <GIC_SPI 218 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 219 IRQ_TYPE_LEVEL_HIGH>,
@@ -375,7 +376,7 @@
 			status = "disabled";
 		};
 
-		mshc_0: mshc@12510000 {
+		mshc_0: mmc@12510000 {
 			compatible = "samsung,exynos5420-dw-mshc";
 			reg = <0x12510000 0x1000>;
 			interrupts = <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>;
@@ -387,7 +388,7 @@
 			status = "disabled";
 		};
 
-		mshc_1: mshc@12520000 {
+		mshc_1: mmc@12520000 {
 			compatible = "samsung,exynos5420-dw-mshc";
 			reg = <0x12520000 0x1000>;
 			interrupts = <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>;
@@ -399,7 +400,7 @@
 			status = "disabled";
 		};
 
-		mshc_2: mshc@12530000 {
+		mshc_2: mmc@12530000 {
 			compatible = "samsung,exynos5250-dw-mshc";
 			reg = <0x12530000 0x1000>;
 			interrupts = <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>;
@@ -421,26 +422,22 @@
 			status = "disabled";
 		};
 
-		pdma0: pdma@12680000 {
+		pdma0: dma-controller@12680000 {
 			compatible = "arm,pl330", "arm,primecell";
 			reg = <0x12680000 0x1000>;
 			interrupts = <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cmu CLK_PDMA0>;
 			clock-names = "apb_pclk";
 			#dma-cells = <1>;
-			#dma-channels = <8>;
-			#dma-requests = <32>;
 		};
 
-		pdma1: pdma@12690000 {
+		pdma1: dma-controller@12690000 {
 			compatible = "arm,pl330", "arm,primecell";
 			reg = <0x12690000 0x1000>;
 			interrupts = <GIC_SPI 139 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cmu CLK_PDMA1>;
 			clock-names = "apb_pclk";
 			#dma-cells = <1>;
-			#dma-channels = <8>;
-			#dma-requests = <32>;
 		};
 
 		adc: adc@126c0000 {
diff --git a/arch/arm/boot/dts/exynos4.dtsi b/arch/arm/boot/dts/exynos4.dtsi
index eab77a66ae8f..5c4ecda27a47 100644
--- a/arch/arm/boot/dts/exynos4.dtsi
+++ b/arch/arm/boot/dts/exynos4.dtsi
@@ -316,7 +316,7 @@
 			status = "disabled";
 		};
 
-		sdhci_0: sdhci@12510000 {
+		sdhci_0: mmc@12510000 {
 			compatible = "samsung,exynos4210-sdhci";
 			reg = <0x12510000 0x100>;
 			interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
@@ -325,7 +325,7 @@
 			status = "disabled";
 		};
 
-		sdhci_1: sdhci@12520000 {
+		sdhci_1: mmc@12520000 {
 			compatible = "samsung,exynos4210-sdhci";
 			reg = <0x12520000 0x100>;
 			interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
@@ -334,7 +334,7 @@
 			status = "disabled";
 		};
 
-		sdhci_2: sdhci@12530000 {
+		sdhci_2: mmc@12530000 {
 			compatible = "samsung,exynos4210-sdhci";
 			reg = <0x12530000 0x100>;
 			interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
@@ -343,7 +343,7 @@
 			status = "disabled";
 		};
 
-		sdhci_3: sdhci@12540000 {
+		sdhci_3: mmc@12540000 {
 			compatible = "samsung,exynos4210-sdhci";
 			reg = <0x12540000 0x100>;
 			interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
@@ -373,7 +373,7 @@
 			status = "disabled";
 		};
 
-		ehci: ehci@12580000 {
+		ehci: usb@12580000 {
 			compatible = "samsung,exynos4210-ehci";
 			reg = <0x12580000 0x100>;
 			interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
@@ -384,7 +384,7 @@
 			phy-names = "host", "hsic0", "hsic1";
 		};
 
-		ohci: ohci@12590000 {
+		ohci: usb@12590000 {
 			compatible = "samsung,exynos4210-ohci";
 			reg = <0x12590000 0x100>;
 			interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
@@ -669,37 +669,31 @@
 			status = "disabled";
 		};
 
-		pdma0: pdma@12680000 {
+		pdma0: dma-controller@12680000 {
 			compatible = "arm,pl330", "arm,primecell";
 			reg = <0x12680000 0x1000>;
 			interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&clock CLK_PDMA0>;
 			clock-names = "apb_pclk";
 			#dma-cells = <1>;
-			#dma-channels = <8>;
-			#dma-requests = <32>;
 		};
 
-		pdma1: pdma@12690000 {
+		pdma1: dma-controller@12690000 {
 			compatible = "arm,pl330", "arm,primecell";
 			reg = <0x12690000 0x1000>;
 			interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&clock CLK_PDMA1>;
 			clock-names = "apb_pclk";
 			#dma-cells = <1>;
-			#dma-channels = <8>;
-			#dma-requests = <32>;
 		};
 
-		mdma1: mdma@12850000 {
+		mdma1: dma-controller@12850000 {
 			compatible = "arm,pl330", "arm,primecell";
 			reg = <0x12850000 0x1000>;
 			interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&clock CLK_MDMA>;
 			clock-names = "apb_pclk";
 			#dma-cells = <1>;
-			#dma-channels = <8>;
-			#dma-requests = <1>;
 		};
 
 		fimd: fimd@11c00000 {
diff --git a/arch/arm/boot/dts/exynos4210-i9100.dts b/arch/arm/boot/dts/exynos4210-i9100.dts
index 19bb7dc98b33..bba85011ecc9 100644
--- a/arch/arm/boot/dts/exynos4210-i9100.dts
+++ b/arch/arm/boot/dts/exynos4210-i9100.dts
@@ -89,21 +89,21 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		vol-down {
+		key-vol-down {
 			gpios = <&gpx2 1 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_VOLUMEDOWN>;
 			label = "volume down";
 			debounce-interval = <10>;
 		};
 
-		vol-up {
+		key-vol-up {
 			gpios = <&gpx2 0 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_VOLUMEUP>;
 			label = "volume up";
 			debounce-interval = <10>;
 		};
 
-		power {
+		key-power {
 			gpios = <&gpx2 7 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
 			label = "power";
@@ -111,7 +111,7 @@
 			wakeup-source;
 		};
 
-		ok {
+		key-ok {
 			gpios = <&gpx3 5 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_OK>;
 			label = "ok";
@@ -672,26 +672,26 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&sleep0>;
 
-	sleep0: sleep-states {
-		gpa0-0 {
+	sleep0: sleep-state {
+		gpa0-0-pin {
 			samsung,pins = "gpa0-0";
 			samsung,pin-con-pdn = <EXYNOS_PIN_PDN_INPUT>;
 			samsung,pin-pud-pdn = <EXYNOS_PIN_PULL_NONE>;
 		};
 
-		gpa0-1 {
+		gpa0-1-pin {
 			samsung,pins = "gpa0-1";
 			samsung,pin-con-pdn = <EXYNOS_PIN_PDN_OUT0>;
 			samsung,pin-pud-pdn = <EXYNOS_PIN_PULL_NONE>;
 		};
 
-		gpa0-2 {
+		gpa0-2-pin {
 			samsung,pins = "gpa0-2";
 			samsung,pin-con-pdn = <EXYNOS_PIN_PDN_INPUT>;
 			samsung,pin-pud-pdn = <EXYNOS_PIN_PULL_NONE>;
 		};
 
-		gpa0-3 {
+		gpa0-3-pin {
 			samsung,pins = "gpa0-3";
 			samsung,pin-con-pdn = <EXYNOS_PIN_PDN_OUT1>;
 			samsung,pin-pud-pdn = <EXYNOS_PIN_PULL_NONE>;
@@ -700,19 +700,19 @@
 };
 
 &pinctrl_1 {
-	mhl_int: mhl-int {
+	mhl_int: mhl-int-pins {
 		samsung,pins = "gpf3-5";
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 	};
 
-	i2c_mhl_bus: i2c-mhl-bus {
+	i2c_mhl_bus: i2c-mhl-bus-pins {
 		samsung,pins = "gpf0-4", "gpf0-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	usb_sel: usb-sel {
+	usb_sel: usb-sel-pins {
 		samsung,pins = "gpl0-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
@@ -720,7 +720,7 @@
 		samsung,pin-val = <0>;
 	};
 
-	bt_en: bt-en {
+	bt_en: bt-en-pins {
 		samsung,pins = "gpl0-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
@@ -728,7 +728,7 @@
 		samsung,pin-val = <0>;
 	};
 
-	bt_res: bt-res {
+	bt_res: bt-res-pins {
 		samsung,pins = "gpl1-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
@@ -736,7 +736,7 @@
 		samsung,pin-val = <0>;
 	};
 
-	otg_gp: otg-gp {
+	otg_gp: otg-gp-pins {
 		samsung,pins = "gpx3-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
@@ -744,23 +744,23 @@
 		samsung,pin-val = <0>;
 	};
 
-	mag_mhl_gpio: mag-mhl {
+	mag_mhl_gpio: mag-mhl-pins {
 		samsung,pins = "gpd0-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 	};
 
-	max8997_irq: max8997-irq {
+	max8997_irq: max8997-irq-pins {
 		samsung,pins = "gpx0-7";
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 	};
 
-	max17042_fuel_irq: max17042-fuel-irq {
+	max17042_fuel_irq: max17042-fuel-irq-pins {
 		samsung,pins = "gpx2-3";
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 	};
 
-	tsp224_irq: tsp224-irq {
+	tsp224_irq: tsp224-irq-pins {
 		samsung,pins = "gpx0-4";
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 	};
@@ -828,9 +828,12 @@
 		compatible = "brcm,bcm4330-bt";
 
 		shutdown-gpios = <&gpl0 4 GPIO_ACTIVE_HIGH>;
-		reset-gpios = <&gpl1 0 GPIO_ACTIVE_HIGH>;
+		reset-gpios = <&gpl1 0 GPIO_ACTIVE_LOW>;
 		device-wakeup-gpios = <&gpx3 1 GPIO_ACTIVE_HIGH>;
-		host-wakeup-gpios = <&gpx2 6 GPIO_ACTIVE_HIGH>;
+
+		interrupt-parent = <&gpx2>;
+		interrupts = <6 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-names = "host-wakeup";
 	};
 };
 
diff --git a/arch/arm/boot/dts/exynos4210-origen.dts b/arch/arm/boot/dts/exynos4210-origen.dts
index 435fda60e86d..5f37b751f700 100644
--- a/arch/arm/boot/dts/exynos4210-origen.dts
+++ b/arch/arm/boot/dts/exynos4210-origen.dts
@@ -15,6 +15,7 @@
 #include "exynos4210.dtsi"
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
 #include "exynos-mfc-reserved-memory.dtsi"
 
 / {
@@ -46,35 +47,35 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		up {
+		key-up {
 			label = "Up";
 			gpios = <&gpx2 0 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_UP>;
 			wakeup-source;
 		};
 
-		down {
+		key-down {
 			label = "Down";
 			gpios = <&gpx2 1 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_DOWN>;
 			wakeup-source;
 		};
 
-		back {
+		key-back {
 			label = "Back";
 			gpios = <&gpx1 7 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_BACK>;
 			wakeup-source;
 		};
 
-		home {
+		key-home {
 			label = "Home";
 			gpios = <&gpx1 6 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_HOME>;
 			wakeup-source;
 		};
 
-		menu {
+		key-menu {
 			label = "Menu";
 			gpios = <&gpx1 5 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_MENU>;
@@ -86,6 +87,7 @@
 		compatible = "gpio-leds";
 		status {
 			gpios = <&gpx1 3 GPIO_ACTIVE_LOW>;
+			function = LED_FUNCTION_HEARTBEAT;
 			linux,default-trigger = "heartbeat";
 		};
 	};
@@ -316,7 +318,7 @@
 };
 
 &pinctrl_1 {
-	max8997_irq: max8997-irq {
+	max8997_irq: max8997-irq-pins {
 		samsung,pins = "gpx0-3", "gpx0-4";
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 	};
diff --git a/arch/arm/boot/dts/exynos4210-pinctrl.dtsi b/arch/arm/boot/dts/exynos4210-pinctrl.dtsi
index 520c5934a8d4..76f44ae0de46 100644
--- a/arch/arm/boot/dts/exynos4210-pinctrl.dtsi
+++ b/arch/arm/boot/dts/exynos4210-pinctrl.dtsi
@@ -11,10 +11,10 @@
  * tree nodes are listed in this file.
  */
 
-#include <dt-bindings/pinctrl/samsung.h>
+#include "exynos-pinctrl.h"
 
 &pinctrl_0 {
-	gpa0: gpa0 {
+	gpa0: gpa0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -22,7 +22,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpa1: gpa1 {
+	gpa1: gpa1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -30,7 +30,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpb: gpb {
+	gpb: gpb-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -38,7 +38,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpc0: gpc0 {
+	gpc0: gpc0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -46,7 +46,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpc1: gpc1 {
+	gpc1: gpc1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -54,7 +54,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpd0: gpd0 {
+	gpd0: gpd0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -62,7 +62,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpd1: gpd1 {
+	gpd1: gpd1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -70,7 +70,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpe0: gpe0 {
+	gpe0: gpe0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -78,7 +78,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpe1: gpe1 {
+	gpe1: gpe1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -86,7 +86,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpe2: gpe2 {
+	gpe2: gpe2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -94,7 +94,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpe3: gpe3 {
+	gpe3: gpe3-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -102,7 +102,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpe4: gpe4 {
+	gpe4: gpe4-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -110,7 +110,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpf0: gpf0 {
+	gpf0: gpf0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -118,7 +118,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpf1: gpf1 {
+	gpf1: gpf1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -126,7 +126,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpf2: gpf2 {
+	gpf2: gpf2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -134,7 +134,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpf3: gpf3 {
+	gpf3: gpf3-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -142,112 +142,112 @@
 		#interrupt-cells = <2>;
 	};
 
-	uart0_data: uart0-data {
+	uart0_data: uart0-data-pins {
 		samsung,pins = "gpa0-0", "gpa0-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	uart0_fctl: uart0-fctl {
+	uart0_fctl: uart0-fctl-pins {
 		samsung,pins = "gpa0-2", "gpa0-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	uart1_data: uart1-data {
+	uart1_data: uart1-data-pins {
 		samsung,pins = "gpa0-4", "gpa0-5";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	uart1_fctl: uart1-fctl {
+	uart1_fctl: uart1-fctl-pins {
 		samsung,pins = "gpa0-6", "gpa0-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2c2_bus: i2c2-bus {
+	i2c2_bus: i2c2-bus-pins {
 		samsung,pins = "gpa0-6", "gpa0-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	uart2_data: uart2-data {
+	uart2_data: uart2-data-pins {
 		samsung,pins = "gpa1-0", "gpa1-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	uart2_fctl: uart2-fctl {
+	uart2_fctl: uart2-fctl-pins {
 		samsung,pins = "gpa1-2", "gpa1-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	uart_audio_a: uart-audio-a {
+	uart_audio_a: uart-audio-a-pins {
 		samsung,pins = "gpa1-0", "gpa1-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2c3_bus: i2c3-bus {
+	i2c3_bus: i2c3-bus-pins {
 		samsung,pins = "gpa1-2", "gpa1-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	uart3_data: uart3-data {
+	uart3_data: uart3-data-pins {
 		samsung,pins = "gpa1-4", "gpa1-5";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	uart_audio_b: uart-audio-b {
+	uart_audio_b: uart-audio-b-pins {
 		samsung,pins = "gpa1-4", "gpa1-5";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	spi0_bus: spi0-bus {
+	spi0_bus: spi0-bus-pins {
 		samsung,pins = "gpb-0", "gpb-2", "gpb-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2c4_bus: i2c4-bus {
+	i2c4_bus: i2c4-bus-pins {
 		samsung,pins = "gpb-2", "gpb-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	spi1_bus: spi1-bus {
+	spi1_bus: spi1-bus-pins {
 		samsung,pins = "gpb-4", "gpb-6", "gpb-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2c5_bus: i2c5-bus {
+	i2c5_bus: i2c5-bus-pins {
 		samsung,pins = "gpb-6", "gpb-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2s1_bus: i2s1-bus {
+	i2s1_bus: i2s1-bus-pins {
 		samsung,pins = "gpc0-0", "gpc0-1", "gpc0-2", "gpc0-3",
 				"gpc0-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
@@ -255,7 +255,7 @@
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	pcm1_bus: pcm1-bus {
+	pcm1_bus: pcm1-bus-pins {
 		samsung,pins = "gpc0-0", "gpc0-1", "gpc0-2", "gpc0-3",
 				"gpc0-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
@@ -263,7 +263,7 @@
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	ac97_bus: ac97-bus {
+	ac97_bus: ac97-bus-pins {
 		samsung,pins = "gpc0-0", "gpc0-1", "gpc0-2", "gpc0-3",
 				"gpc0-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
@@ -271,7 +271,7 @@
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2s2_bus: i2s2-bus {
+	i2s2_bus: i2s2-bus-pins {
 		samsung,pins = "gpc1-0", "gpc1-1", "gpc1-2", "gpc1-3",
 				"gpc1-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
@@ -279,7 +279,7 @@
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	pcm2_bus: pcm2-bus {
+	pcm2_bus: pcm2-bus-pins {
 		samsung,pins = "gpc1-0", "gpc1-1", "gpc1-2", "gpc1-3",
 				"gpc1-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
@@ -287,105 +287,105 @@
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	spdif_bus: spdif-bus {
+	spdif_bus: spdif-bus-pins {
 		samsung,pins = "gpc1-0", "gpc1-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2c6_bus: i2c6-bus {
+	i2c6_bus: i2c6-bus-pins {
 		samsung,pins = "gpc1-3", "gpc1-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	spi2_bus: spi2-bus {
+	spi2_bus: spi2-bus-pins {
 		samsung,pins = "gpc1-1", "gpc1-2", "gpc1-3", "gpc1-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_5>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2c7_bus: i2c7-bus {
+	i2c7_bus: i2c7-bus-pins {
 		samsung,pins = "gpd0-2", "gpd0-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2c0_bus: i2c0-bus {
+	i2c0_bus: i2c0-bus-pins {
 		samsung,pins = "gpd1-0", "gpd1-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2c1_bus: i2c1-bus {
+	i2c1_bus: i2c1-bus-pins {
 		samsung,pins = "gpd1-2", "gpd1-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	pwm0_out: pwm0-out {
+	pwm0_out: pwm0-out-pins {
 		samsung,pins = "gpd0-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	pwm1_out: pwm1-out {
+	pwm1_out: pwm1-out-pins {
 		samsung,pins = "gpd0-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	pwm2_out: pwm2-out {
+	pwm2_out: pwm2-out-pins {
 		samsung,pins = "gpd0-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	pwm3_out: pwm3-out {
+	pwm3_out: pwm3-out-pins {
 		samsung,pins = "gpd0-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	lcd_ctrl: lcd-ctrl {
+	lcd_ctrl: lcd-ctrl-pins {
 		samsung,pins = "gpd0-0", "gpd0-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	lcd_sync: lcd-sync {
+	lcd_sync: lcd-sync-pins {
 		samsung,pins = "gpf0-0", "gpf0-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	lcd_en: lcd-en {
+	lcd_en: lcd-en-pins {
 		samsung,pins = "gpe3-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	lcd_clk: lcd-clk {
+	lcd_clk: lcd-clk-pins {
 		samsung,pins = "gpf0-0", "gpf0-1", "gpf0-2", "gpf0-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	lcd_data16: lcd-data-width16 {
+	lcd_data16: lcd-data-width16-pins {
 		samsung,pins = "gpf0-7", "gpf1-0", "gpf1-1", "gpf1-2",
 				"gpf1-3", "gpf1-6", "gpf1-7", "gpf2-0",
 				"gpf2-1", "gpf2-2", "gpf2-3", "gpf2-7",
@@ -395,7 +395,7 @@
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	lcd_data18: lcd-data-width18 {
+	lcd_data18: lcd-data-width18-pins {
 		samsung,pins = "gpf0-6", "gpf0-7", "gpf1-0", "gpf1-1",
 				"gpf1-2", "gpf1-3", "gpf1-6", "gpf1-7",
 				"gpf2-0", "gpf2-1", "gpf2-2", "gpf2-3",
@@ -406,7 +406,7 @@
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	lcd_data24: lcd-data-width24 {
+	lcd_data24: lcd-data-width24-pins {
 		samsung,pins = "gpf0-4", "gpf0-5", "gpf0-6", "gpf0-7",
 				"gpf1-0", "gpf1-1", "gpf1-2", "gpf1-3",
 				"gpf1-4", "gpf1-5", "gpf1-6", "gpf1-7",
@@ -420,7 +420,7 @@
 };
 
 &pinctrl_1 {
-	gpj0: gpj0 {
+	gpj0: gpj0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -428,7 +428,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpj1: gpj1 {
+	gpj1: gpj1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -436,7 +436,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpk0: gpk0 {
+	gpk0: gpk0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -444,7 +444,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpk1: gpk1 {
+	gpk1: gpk1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -452,7 +452,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpk2: gpk2 {
+	gpk2: gpk2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -460,7 +460,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpk3: gpk3 {
+	gpk3: gpk3-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -468,7 +468,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpl0: gpl0 {
+	gpl0: gpl0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -476,7 +476,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpl1: gpl1 {
+	gpl1: gpl1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -484,7 +484,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpl2: gpl2 {
+	gpl2: gpl2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -492,42 +492,42 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpy0: gpy0 {
+	gpy0: gpy0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpy1: gpy1 {
+	gpy1: gpy1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpy2: gpy2 {
+	gpy2: gpy2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpy3: gpy3 {
+	gpy3: gpy3-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpy4: gpy4 {
+	gpy4: gpy4-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpy5: gpy5 {
+	gpy5: gpy5-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpy6: gpy6 {
+	gpy6: gpy6-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpx0: gpx0 {
+	gpx0: gpx0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -544,7 +544,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpx1: gpx1 {
+	gpx1: gpx1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -561,7 +561,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpx2: gpx2 {
+	gpx2: gpx2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -569,7 +569,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpx3: gpx3 {
+	gpx3: gpx3-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -577,238 +577,238 @@
 		#interrupt-cells = <2>;
 	};
 
-	sd0_clk: sd0-clk {
+	sd0_clk: sd0-clk-pins {
 		samsung,pins = "gpk0-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd0_cmd: sd0-cmd {
+	sd0_cmd: sd0-cmd-pins {
 		samsung,pins = "gpk0-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd0_cd: sd0-cd {
+	sd0_cd: sd0-cd-pins {
 		samsung,pins = "gpk0-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd0_bus1: sd0-bus-width1 {
+	sd0_bus1: sd0-bus-width1-pins {
 		samsung,pins = "gpk0-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd0_bus4: sd0-bus-width4 {
+	sd0_bus4: sd0-bus-width4-pins {
 		samsung,pins = "gpk0-3", "gpk0-4", "gpk0-5", "gpk0-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd0_bus8: sd0-bus-width8 {
+	sd0_bus8: sd0-bus-width8-pins {
 		samsung,pins = "gpk1-3", "gpk1-4", "gpk1-5", "gpk1-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd4_clk: sd4-clk {
+	sd4_clk: sd4-clk-pins {
 		samsung,pins = "gpk0-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd4_cmd: sd4-cmd {
+	sd4_cmd: sd4-cmd-pins {
 		samsung,pins = "gpk0-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd4_cd: sd4-cd {
+	sd4_cd: sd4-cd-pins {
 		samsung,pins = "gpk0-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd4_bus1: sd4-bus-width1 {
+	sd4_bus1: sd4-bus-width1-pins {
 		samsung,pins = "gpk0-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd4_bus4: sd4-bus-width4 {
+	sd4_bus4: sd4-bus-width4-pins {
 		samsung,pins = "gpk0-3", "gpk0-4", "gpk0-5", "gpk0-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd4_bus8: sd4-bus-width8 {
+	sd4_bus8: sd4-bus-width8-pins {
 		samsung,pins = "gpk1-3", "gpk1-4", "gpk1-5", "gpk1-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd1_clk: sd1-clk {
+	sd1_clk: sd1-clk-pins {
 		samsung,pins = "gpk1-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd1_cmd: sd1-cmd {
+	sd1_cmd: sd1-cmd-pins {
 		samsung,pins = "gpk1-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd1_cd: sd1-cd {
+	sd1_cd: sd1-cd-pins {
 		samsung,pins = "gpk1-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd1_bus1: sd1-bus-width1 {
+	sd1_bus1: sd1-bus-width1-pins {
 		samsung,pins = "gpk1-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd1_bus4: sd1-bus-width4 {
+	sd1_bus4: sd1-bus-width4-pins {
 		samsung,pins = "gpk1-3", "gpk1-4", "gpk1-5", "gpk1-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd2_clk: sd2-clk {
+	sd2_clk: sd2-clk-pins {
 		samsung,pins = "gpk2-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd2_cmd: sd2-cmd {
+	sd2_cmd: sd2-cmd-pins {
 		samsung,pins = "gpk2-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd2_cd: sd2-cd {
+	sd2_cd: sd2-cd-pins {
 		samsung,pins = "gpk2-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd2_bus1: sd2-bus-width1 {
+	sd2_bus1: sd2-bus-width1-pins {
 		samsung,pins = "gpk2-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd2_bus4: sd2-bus-width4 {
+	sd2_bus4: sd2-bus-width4-pins {
 		samsung,pins = "gpk2-3", "gpk2-4", "gpk2-5", "gpk2-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd2_bus8: sd2-bus-width8 {
+	sd2_bus8: sd2-bus-width8-pins {
 		samsung,pins = "gpk3-3", "gpk3-4", "gpk3-5", "gpk3-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd3_clk: sd3-clk {
+	sd3_clk: sd3-clk-pins {
 		samsung,pins = "gpk3-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd3_cmd: sd3-cmd {
+	sd3_cmd: sd3-cmd-pins {
 		samsung,pins = "gpk3-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd3_cd: sd3-cd {
+	sd3_cd: sd3-cd-pins {
 		samsung,pins = "gpk3-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd3_bus1: sd3-bus-width1 {
+	sd3_bus1: sd3-bus-width1-pins {
 		samsung,pins = "gpk3-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd3_bus4: sd3-bus-width4 {
+	sd3_bus4: sd3-bus-width4-pins {
 		samsung,pins = "gpk3-3", "gpk3-4", "gpk3-5", "gpk3-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	eint0: ext-int0 {
+	eint0: ext-int0-pins {
 		samsung,pins = "gpx0-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	eint8: ext-int8 {
+	eint8: ext-int8-pins {
 		samsung,pins = "gpx1-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	eint15: ext-int15 {
+	eint15: ext-int15-pins {
 		samsung,pins = "gpx1-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	eint16: ext-int16 {
+	eint16: ext-int16-pins {
 		samsung,pins = "gpx2-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	eint31: ext-int31 {
+	eint31: ext-int31-pins {
 		samsung,pins = "gpx3-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	cam_port_a_io: cam-port-a-io {
+	cam_port_a_io: cam-port-a-io-pins {
 		samsung,pins = "gpj0-0", "gpj0-1", "gpj0-2", "gpj0-3",
 				"gpj0-4", "gpj0-5", "gpj0-6", "gpj0-7",
 				"gpj1-0", "gpj1-1", "gpj1-2", "gpj1-4";
@@ -817,21 +817,21 @@
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	cam_port_a_clk_active: cam-port-a-clk-active {
+	cam_port_a_clk_active: cam-port-a-clk-active-pins {
 		samsung,pins = "gpj1-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	cam_port_a_clk_idle: cam-port-a-clk-idle {
+	cam_port_a_clk_idle: cam-port-a-clk-idle-pins {
 		samsung,pins = "gpj1-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	hdmi_cec: hdmi-cec {
+	hdmi_cec: hdmi-cec-pins {
 		samsung,pins = "gpx3-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
@@ -840,12 +840,12 @@
 };
 
 &pinctrl_2 {
-	gpz: gpz {
+	gpz: gpz-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	i2s0_bus: i2s0-bus {
+	i2s0_bus: i2s0-bus-pins {
 		samsung,pins = "gpz-0", "gpz-1", "gpz-2", "gpz-3",
 				"gpz-4", "gpz-5", "gpz-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
@@ -853,7 +853,7 @@
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	pcm0_bus: pcm0-bus {
+	pcm0_bus: pcm0-bus-pins {
 		samsung,pins = "gpz-0", "gpz-1", "gpz-2", "gpz-3",
 				"gpz-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
diff --git a/arch/arm/boot/dts/exynos4210-smdkv310.dts b/arch/arm/boot/dts/exynos4210-smdkv310.dts
index d5797a67bf48..a5dfd7fd49b3 100644
--- a/arch/arm/boot/dts/exynos4210-smdkv310.dts
+++ b/arch/arm/boot/dts/exynos4210-smdkv310.dts
@@ -152,14 +152,14 @@
 };
 
 &pinctrl_1 {
-	keypad_rows: keypad-rows {
+	keypad_rows: keypad-rows-pins {
 		samsung,pins = "gpx2-0", "gpx2-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	keypad_cols: keypad-cols {
+	keypad_cols: keypad-cols-pins {
 		samsung,pins = "gpx1-0", "gpx1-1", "gpx1-2", "gpx1-3",
 			       "gpx1-4", "gpx1-5", "gpx1-6", "gpx1-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
diff --git a/arch/arm/boot/dts/exynos4210-trats.dts b/arch/arm/boot/dts/exynos4210-trats.dts
index 9c4ff7521348..b8e9dd23fc51 100644
--- a/arch/arm/boot/dts/exynos4210-trats.dts
+++ b/arch/arm/boot/dts/exynos4210-trats.dts
@@ -180,7 +180,7 @@
 		vdd3-supply = <&vcclcd_reg>;
 		vci-supply = <&vlcd_reg>;
 		reset-gpios = <&gpy4 5 GPIO_ACTIVE_HIGH>;
-		power-on-delay= <50>;
+		power-on-delay = <50>;
 		reset-delay = <100>;
 		init-delay = <100>;
 		flip-horizontal;
@@ -464,19 +464,19 @@
 };
 
 &pinctrl_1 {
-	bt_shutdown: bt-shutdown {
+	bt_shutdown: bt-shutdown-pins {
 		samsung,pins = "gpl1-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 	};
 
-	bt_host_wakeup: bt-host-wakeup {
+	bt_host_wakeup: bt-host-wakeup-pins {
 		samsung,pins = "gpx2-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 	};
 
-	bt_device_wakeup: bt-device-wakeup {
+	bt_device_wakeup: bt-device-wakeup-pins {
 		samsung,pins = "gpx3-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
diff --git a/arch/arm/boot/dts/exynos4210-universal_c210.dts b/arch/arm/boot/dts/exynos4210-universal_c210.dts
index 9f93e7464aed..62bf335d5bed 100644
--- a/arch/arm/boot/dts/exynos4210-universal_c210.dts
+++ b/arch/arm/boot/dts/exynos4210-universal_c210.dts
@@ -533,37 +533,37 @@
 };
 
 &pinctrl_1 {
-	bt_shutdown: bt-shutdown {
+	bt_shutdown: bt-shutdown-pins {
 		samsung,pins = "gpe1-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 	};
 
-	bt_host_wakeup: bt-host-wakeup {
+	bt_host_wakeup: bt-host-wakeup-pins {
 		samsung,pins = "gpx2-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 	};
 
-	bt_device_wakeup: bt-device-wakeup {
+	bt_device_wakeup: bt-device-wakeup-pins {
 		samsung,pins = "gpx3-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 	};
 
-	lp3974_irq: lp3974-irq {
+	lp3974_irq: lp3974-irq-pins {
 		samsung,pins = "gpx0-7", "gpx2-7";
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 	};
 
-	hdmi_hpd: hdmi-hpd {
+	hdmi_hpd: hdmi-hpd-pins {
 		samsung,pins = "gpx3-7";
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 	};
 };
 
 &pinctrl_0 {
-	i2c_ddc_bus: i2c-ddc-bus {
+	i2c_ddc_bus: i2c-ddc-bus-pins {
 		samsung,pins = "gpe4-2", "gpe4-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
@@ -659,15 +659,13 @@
 };
 
 &soc {
-	mdma0: mdma@12840000 {
+	mdma0: dma-controller@12840000 {
 		compatible = "arm,pl330", "arm,primecell";
 		reg = <0x12840000 0x1000>;
 		interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&clock CLK_MDMA>;
 		clock-names = "apb_pclk";
 		#dma-cells = <1>;
-		#dma-channels = <8>;
-		#dma-requests = <1>;
 		power-domains = <&pd_lcd0>;
 	};
 };
diff --git a/arch/arm/boot/dts/exynos4210.dtsi b/arch/arm/boot/dts/exynos4210.dtsi
index 7e7d65ce6585..2c25cc37934e 100644
--- a/arch/arm/boot/dts/exynos4210.dtsi
+++ b/arch/arm/boot/dts/exynos4210.dtsi
@@ -527,8 +527,6 @@
 	compatible = "samsung,exynos4210-tmu";
 	clocks = <&clock CLK_TMU_APBIF>;
 	clock-names = "tmu_apbif";
-	samsung,tmu_gain = <15>;
-	samsung,tmu_reference_voltage = <7>;
 };
 
 #include "exynos4210-pinctrl.dtsi"
diff --git a/arch/arm/boot/dts/exynos4412-galaxy-s3.dtsi b/arch/arm/boot/dts/exynos4412-galaxy-s3.dtsi
index c14e37dc3a9b..94122e9c6625 100644
--- a/arch/arm/boot/dts/exynos4412-galaxy-s3.dtsi
+++ b/arch/arm/boot/dts/exynos4412-galaxy-s3.dtsi
@@ -7,6 +7,7 @@
  */
 
 /dts-v1/;
+#include <dt-bindings/leds/common.h>
 #include "exynos4412-midas.dtsi"
 
 / {
@@ -25,8 +26,9 @@
 		pinctrl-1 = <&camera_flash_host>;
 		pinctrl-2 = <&camera_flash_isp>;
 
-		flash-led {
-			label = "flash";
+		led {
+			function = LED_FUNCTION_FLASH;
+			color = <LED_COLOR_ID_WHITE>;
 			led-max-microamp = <520833>;
 			flash-max-microamp = <1012500>;
 			flash-max-timeout-us = <1940000>;
@@ -107,7 +109,7 @@
 		vdd3-supply = <&lcd_vdd3_reg>;
 		vci-supply = <&ldo25_reg>;
 		reset-gpios = <&gpf2 1 GPIO_ACTIVE_HIGH>;
-		power-on-delay= <50>;
+		power-on-delay = <50>;
 		reset-delay = <100>;
 		init-delay = <100>;
 		flip-horizontal;
@@ -151,13 +153,13 @@
 };
 
 &pinctrl_0 {
-	camera_flash_host: camera-flash-host {
+	camera_flash_host: camera-flash-host-pins {
 		samsung,pins = "gpj1-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 		samsung,pin-val = <0>;
 	};
 
-	camera_flash_isp: camera-flash-isp {
+	camera_flash_isp: camera-flash-isp-pins {
 		samsung,pins = "gpj1-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 		samsung,pin-val = <1>;
diff --git a/arch/arm/boot/dts/exynos4412-itop-elite.dts b/arch/arm/boot/dts/exynos4412-itop-elite.dts
index 47431307cb3c..202ab0fee3b7 100644
--- a/arch/arm/boot/dts/exynos4412-itop-elite.dts
+++ b/arch/arm/boot/dts/exynos4412-itop-elite.dts
@@ -11,6 +11,7 @@
  */
 
 /dts-v1/;
+#include <dt-bindings/leds/common.h>
 #include <dt-bindings/pwm/pwm.h>
 #include <dt-bindings/sound/samsung-i2s.h>
 #include "exynos4412-itop-scp-core.dtsi"
@@ -28,7 +29,8 @@
 		compatible = "gpio-leds";
 
 		led2 {
-			label = "red:system";
+			function = LED_FUNCTION_HEARTBEAT;
+			color = <LED_COLOR_ID_RED>;
 			gpios = <&gpx1 0 GPIO_ACTIVE_HIGH>;
 			default-state = "off";
 			linux,default-trigger = "heartbeat";
@@ -36,6 +38,7 @@
 
 		led3 {
 			label = "red:user";
+			color = <LED_COLOR_ID_RED>;
 			gpios = <&gpk1 1 GPIO_ACTIVE_HIGH>;
 			default-state = "off";
 		};
@@ -44,31 +47,31 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		home {
+		key-home {
 			label = "GPIO Key Home";
 			linux,code = <KEY_HOME>;
 			gpios = <&gpx1 1 GPIO_ACTIVE_LOW>;
 		};
 
-		back {
+		key-back {
 			label = "GPIO Key Back";
 			linux,code = <KEY_BACK>;
 			gpios = <&gpx1 2 GPIO_ACTIVE_LOW>;
 		};
 
-		sleep {
+		key-sleep {
 			label = "GPIO Key Sleep";
 			linux,code = <KEY_POWER>;
 			gpios = <&gpx3 3 GPIO_ACTIVE_LOW>;
 		};
 
-		vol-up {
+		key-vol-up {
 			label = "GPIO Key Vol+";
 			linux,code = <KEY_UP>;
 			gpios = <&gpx2 1 GPIO_ACTIVE_LOW>;
 		};
 
-		vol-down {
+		key-vol-down {
 			label = "GPIO Key Vol-";
 			linux,code = <KEY_DOWN>;
 			gpios = <&gpx2 0 GPIO_ACTIVE_LOW>;
@@ -192,7 +195,7 @@
 };
 
 &pinctrl_1 {
-	ether-reset {
+	ether-reset-pins {
 		samsung,pins = "gpc0-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
diff --git a/arch/arm/boot/dts/exynos4412-itop-scp-core.dtsi b/arch/arm/boot/dts/exynos4412-itop-scp-core.dtsi
index b3726d4d7d93..a67cb61e3cbb 100644
--- a/arch/arm/boot/dts/exynos4412-itop-scp-core.dtsi
+++ b/arch/arm/boot/dts/exynos4412-itop-scp-core.dtsi
@@ -484,7 +484,7 @@
 };
 
 &pinctrl_1 {
-	hsic_reset: hsic-reset {
+	hsic_reset: hsic-reset-pins {
 		samsung,pins = "gpm2-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
diff --git a/arch/arm/boot/dts/exynos4412-midas.dtsi b/arch/arm/boot/dts/exynos4412-midas.dtsi
index 968c7943653e..8e1c19a8ad06 100644
--- a/arch/arm/boot/dts/exynos4412-midas.dtsi
+++ b/arch/arm/boot/dts/exynos4412-midas.dtsi
@@ -12,11 +12,12 @@
 /dts-v1/;
 #include "exynos4412.dtsi"
 #include "exynos4412-ppmu-common.dtsi"
+
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/clock/maxim,max77686.h>
-#include <dt-bindings/pinctrl/samsung.h>
+#include "exynos-pinctrl.h"
 
 / {
 	compatible = "samsung,midas", "samsung,exynos4412", "samsung,exynos4";
@@ -585,7 +586,7 @@
 		clocks = <&camera 1>;
 		clock-names = "extclk";
 		samsung,camclk-out = <1>;
-		gpios = <&gpm1 6 GPIO_ACTIVE_HIGH>;
+		gpios = <&gpm1 6 GPIO_ACTIVE_LOW>;
 
 		port {
 			is_s5k6a3_ep: endpoint {
@@ -987,19 +988,19 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&sleep0>;
 
-	mhl_int: mhl-int {
+	mhl_int: mhl-int-pins {
 		samsung,pins = "gpf3-5";
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 	};
 
-	i2c_mhl_bus: i2c-mhl-bus {
+	i2c_mhl_bus: i2c-mhl-bus-pins {
 		samsung,pins = "gpf0-4", "gpf0-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	sleep0: sleep-states {
+	sleep0: sleep-state {
 		PIN_SLP(gpa0-0, INPUT, NONE);
 		PIN_SLP(gpa0-1, OUT0, NONE);
 		PIN_SLP(gpa0-2, INPUT, NONE);
@@ -1102,52 +1103,52 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&sleep1>;
 
-	gpio_keys: gpio-keys {
+	gpio_keys: gpio-keys-pins {
 		samsung,pins = "gpx0-1", "gpx2-2", "gpx2-7", "gpx3-3";
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 	};
 
-	bt_shutdown: bt-shutdown {
+	bt_shutdown: bt-shutdown-pins {
 		samsung,pins = "gpl0-6";
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 	};
 
-	bt_host_wakeup: bt-host-wakeup {
+	bt_host_wakeup: bt-host-wakeup-pins {
 		samsung,pins = "gpx2-6";
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 	};
 
-	bt_device_wakeup: bt-device-wakeup {
+	bt_device_wakeup: bt-device-wakeup-pins {
 		samsung,pins = "gpx3-1";
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 	};
 
-	max77686_irq: max77686-irq {
+	max77686_irq: max77686-irq-pins {
 		samsung,pins = "gpx0-7";
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 	};
 
-	max77693_irq: max77693-irq {
+	max77693_irq: max77693-irq-pins {
 		samsung,pins = "gpx1-5";
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 	};
 
-	max77693_fuel_irq: max77693-fuel-irq {
+	max77693_fuel_irq: max77693-fuel-irq-pins {
 		samsung,pins = "gpx2-3";
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 	};
 
-	sdhci2_cd: sdhci2-cd-irq {
+	sdhci2_cd: sdhci2-cd-irq-pins {
 		samsung,pins = "gpx3-4";
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 	};
 
-	hdmi_hpd: hdmi-hpd {
+	hdmi_hpd: hdmi-hpd-pins {
 		samsung,pins = "gpx3-7";
 		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
 	};
 
-	sleep1: sleep-states {
+	sleep1: sleep-state {
 		PIN_SLP(gpk0-0, PREV, NONE);
 		PIN_SLP(gpk0-1, PREV, NONE);
 		PIN_SLP(gpk0-2, OUT0, NONE);
@@ -1300,7 +1301,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&sleep2>;
 
-	sleep2: sleep-states {
+	sleep2: sleep-state {
 		PIN_SLP(gpz-0, INPUT, DOWN);
 		PIN_SLP(gpz-1, INPUT, DOWN);
 		PIN_SLP(gpz-2, INPUT, DOWN);
@@ -1315,7 +1316,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&sleep3>;
 
-	sleep3: sleep-states {
+	sleep3: sleep-state {
 		PIN_SLP(gpv0-0, INPUT, DOWN);
 		PIN_SLP(gpv0-1, INPUT, DOWN);
 		PIN_SLP(gpv0-2, INPUT, DOWN);
diff --git a/arch/arm/boot/dts/exynos4412-odroid-common.dtsi b/arch/arm/boot/dts/exynos4412-odroid-common.dtsi
index 5b1d4591b35c..e7669b9e9edb 100644
--- a/arch/arm/boot/dts/exynos4412-odroid-common.dtsi
+++ b/arch/arm/boot/dts/exynos4412-odroid-common.dtsi
@@ -172,24 +172,24 @@
 };
 
 &pinctrl_1 {
-	gpio_power_key: power-key {
+	gpio_power_key: power-key-pins {
 		samsung,pins = "gpx1-3";
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 	};
 
-	max77686_irq: max77686-irq {
+	max77686_irq: max77686-irq-pins {
 		samsung,pins = "gpx3-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	hdmi_hpd: hdmi-hpd {
+	hdmi_hpd: hdmi-hpd-pins {
 		samsung,pins = "gpx3-7";
 		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
 	};
 
-	emmc_rstn: emmc-rstn {
+	emmc_rstn: emmc-rstn-pins {
 		samsung,pins = "gpk1-2";
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 	};
diff --git a/arch/arm/boot/dts/exynos4412-odroidu3.dts b/arch/arm/boot/dts/exynos4412-odroidu3.dts
index efaf7533e84f..a5ad88b897ff 100644
--- a/arch/arm/boot/dts/exynos4412-odroidu3.dts
+++ b/arch/arm/boot/dts/exynos4412-odroidu3.dts
@@ -9,6 +9,7 @@
  */
 
 /dts-v1/;
+#include <dt-bindings/leds/common.h>
 #include "exynos4412-odroid-common.dtsi"
 #include "exynos4412-prime.dtsi"
 
@@ -37,7 +38,8 @@
 	leds {
 		compatible = "gpio-leds";
 		led1 {
-			label = "led1:heart";
+			function = LED_FUNCTION_HEARTBEAT;
+			color = <LED_COLOR_ID_BLUE>;
 			gpios = <&gpc1 0 GPIO_ACTIVE_LOW>;
 			default-state = "on";
 			linux,default-trigger = "heartbeat";
@@ -119,8 +121,8 @@
 	phys = <&exynos_usbphy 2>, <&exynos_usbphy 3>;
 	phy-names = "hsic0", "hsic1";
 
-	ethernet: usbether@2 {
-		compatible = "usb0424,9730";
+	ethernet: ethernet@2 {
+		compatible = "usb424,9730";
 		reg = <2>;
 		local-mac-address = [00 00 00 00 00 00]; /* Filled in by a bootloader */
 	};
diff --git a/arch/arm/boot/dts/exynos4412-odroidx.dts b/arch/arm/boot/dts/exynos4412-odroidx.dts
index 440135d0ff2a..68d589e081bc 100644
--- a/arch/arm/boot/dts/exynos4412-odroidx.dts
+++ b/arch/arm/boot/dts/exynos4412-odroidx.dts
@@ -9,6 +9,7 @@
  */
 
 /dts-v1/;
+#include <dt-bindings/leds/common.h>
 #include "exynos4412-odroid-common.dtsi"
 
 / {
@@ -27,13 +28,15 @@
 	leds {
 		compatible = "gpio-leds";
 		led1 {
-			label = "led1:heart";
+			function = LED_FUNCTION_HEARTBEAT;
+			color = <LED_COLOR_ID_BLUE>;
 			gpios = <&gpc1 0 GPIO_ACTIVE_LOW>;
 			default-state = "on";
 			linux,default-trigger = "heartbeat";
 		};
 		led2 {
 			label = "led2:mmc0";
+			function = LED_FUNCTION_DISK_ACTIVITY;
 			gpios = <&gpc1 2 GPIO_ACTIVE_LOW>;
 			default-state = "on";
 			linux,default-trigger = "mmc0";
@@ -70,19 +73,19 @@
 	phy-names = "hsic0";
 
 	hub@2 {
-		compatible = "usb0424,3503";
+		compatible = "usb424,3503";
 		reg = <2>;
 		#address-cells = <1>;
 		#size-cells = <0>;
 
 		hub@1 {
-			compatible = "usb0424,9514";
+			compatible = "usb424,9514";
 			reg = <1>;
 			#address-cells = <1>;
 			#size-cells = <0>;
 
-			ethernet: usbether@1 {
-				compatible = "usb0424,ec00";
+			ethernet: ethernet@1 {
+				compatible = "usb424,ec00";
 				reg = <1>;
 				/* Filled in by a bootloader */
 				local-mac-address = [00 00 00 00 00 00];
@@ -112,7 +115,7 @@
 };
 
 &pinctrl_1 {
-	gpio_home_key: home-key {
+	gpio_home_key: home-key-pins {
 		samsung,pins = "gpx2-2";
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 	};
diff --git a/arch/arm/boot/dts/exynos4412-origen.dts b/arch/arm/boot/dts/exynos4412-origen.dts
index e6aec5facabf..a3905e27b9cd 100644
--- a/arch/arm/boot/dts/exynos4412-origen.dts
+++ b/arch/arm/boot/dts/exynos4412-origen.dts
@@ -95,7 +95,7 @@
 };
 
 &ehci {
-	samsung,vbus-gpio = <&gpx3 5 1>;
+	samsung,vbus-gpio = <&gpx3 5 GPIO_ACTIVE_HIGH>;
 	status = "okay";
 	phys = <&exynos_usbphy 2>, <&exynos_usbphy 3>;
 	phy-names = "hsic0", "hsic1";
@@ -506,14 +506,14 @@
 };
 
 &pinctrl_1 {
-	keypad_rows: keypad-rows {
+	keypad_rows: keypad-rows-pins {
 		samsung,pins = "gpx2-0", "gpx2-1", "gpx2-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	keypad_cols: keypad-cols {
+	keypad_cols: keypad-cols-pins {
 		samsung,pins = "gpx1-0", "gpx1-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
diff --git a/arch/arm/boot/dts/exynos4412-p4note.dtsi b/arch/arm/boot/dts/exynos4412-p4note.dtsi
index 22c3086e0076..7a515b87bc7c 100644
--- a/arch/arm/boot/dts/exynos4412-p4note.dtsi
+++ b/arch/arm/boot/dts/exynos4412-p4note.dtsi
@@ -15,7 +15,8 @@
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/linux-event-codes.h>
 #include <dt-bindings/interrupt-controller/irq.h>
-#include <dt-bindings/pinctrl/samsung.h>
+#include <dt-bindings/power/summit,smb347-charger.h>
+#include "exynos-pinctrl.h"
 
 / {
 	compatible = "samsung,p4note", "samsung,exynos4412", "samsung,exynos4";
@@ -105,6 +106,16 @@
 		regulator-always-on;
 	};
 
+	panel_vdd: voltage-regulator-4 {
+		compatible = "regulator-fixed";
+		regulator-name = "LCD_ENABLE";
+		pinctrl-names = "default";
+		pinctrl-0 = <&lcd_enable>;
+		gpios = <&gpc0 1 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-boot-on;
+	};
+
 	wlan_pwrseq: sdhci3-pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		reset-gpios = <&gpm3 5 GPIO_ACTIVE_LOW>;
@@ -114,6 +125,17 @@
 		clock-names = "ext_clock";
 	};
 
+	battery_cell: battery-cell {
+		compatible = "simple-battery";
+		device-chemistry = "lithium-ion";
+		constant-charge-current-max-microamp = <2200000>;
+		precharge-current-microamp = <250000>;
+		charge-term-current-microamp = <250000>;
+		constant-charge-voltage-max-microvolt = <4200000>;
+
+		power-supplies = <&power_supply>;
+	};
+
 	i2c-gpio-1 {
 		compatible = "i2c-gpio";
 		sda-gpios = <&gpy2 4 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
@@ -182,6 +204,54 @@
 			};
 		};
 	};
+
+	i2c-gpio-4 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpm2 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpm2 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+
+		i2c-gpio,delay-us = <2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		power_supply: charger@6 {
+			compatible = "summit,smb347";
+			reg = <0x6>;
+			summit,enable-usb-charging;
+			summit,enable-charge-control = <SMB3XX_CHG_ENABLE_SW>;
+			summit,fast-voltage-threshold-microvolt = <2600000>;
+			summit,chip-temperature-threshold-celsius = <130>;
+			summit,usb-current-limit-microamp = <1800000>;
+
+			monitored-battery = <&battery_cell>;
+		};
+	};
+
+	panel {
+		compatible = "samsung,ltl101al01";
+		pinctrl-0 = <&lvds_nshdn>;
+		pinctrl-names = "default";
+		power-supply = <&panel_vdd>;
+		enable-gpios = <&gpm0 5 GPIO_ACTIVE_HIGH>;
+		backlight = <&backlight>;
+
+		port {
+			lcd_ep: endpoint {
+				remote-endpoint = <&fimd_ep>;
+			};
+		};
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pinctrl-0 = <&led_bl_reset>;
+		pinctrl-names = "default";
+		enable-gpios = <&gpm0 1 GPIO_ACTIVE_HIGH>;
+		pwms = <&pwm 1 78770 0>;
+		brightness-levels = <0 48 128 255>;
+		num-interpolated-steps = <8>;
+		default-brightness-level = <12>;
+	};
 };
 
 &adc {
@@ -261,22 +331,19 @@
 };
 
 &fimd {
-	pinctrl-0 = <&lcd_clk &lcd_data24 &pwm1_out>;
+	pinctrl-0 = <&lcd_clk &lcd_data24>;
 	pinctrl-names = "default";
+	#address-cells = <1>;
+	#size-cells = <0>;
 	status = "okay";
 
-	display-timings {
-		timing0 {
-			clock-frequency = <66666666>;
-			hactive = <1280>;
-			vactive = <800>;
-			hfront-porch = <18>;
-			hback-porch = <36>;
-			hsync-len = <16>;
-			vback-porch = <16>;
-			vfront-porch = <4>;
-			vsync-len = <3>;
-			hsync-active = <1>;
+	samsung,invert-vclk;
+
+	port@3 {
+		reg = <3>;
+
+		fimd_ep: endpoint {
+			remote-endpoint = <&lcd_ep>;
 		};
 	};
 };
@@ -641,19 +708,25 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&sleep0>;
 
-	tsp_reg_gpio_2: tsp-reg-gpio-2 {
+	tsp_reg_gpio_2: tsp-reg-gpio-2-pins {
 		samsung,pins = "gpb-5";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 	};
 
-	tsp_reg_gpio_3: tsp-reg-gpio-3 {
+	tsp_reg_gpio_3: tsp-reg-gpio-3-pins {
 		samsung,pins = "gpb-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 	};
 
-	sleep0: sleep-states {
+	lcd_enable: lcd-enable-pins {
+		samsung,pins = "gpc0-1";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	sleep0: sleep-state {
 		PIN_SLP(gpa0-0, INPUT, NONE);
 		PIN_SLP(gpa0-1, OUT0, NONE);
 		PIN_SLP(gpa0-2, INPUT, NONE);
@@ -755,19 +828,19 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&sleep1>;
 
-	sd3_wifi: sd3-wifi {
+	sd3_wifi: sd3-wifi-pins {
 		samsung,pins = "gpk3-3", "gpk3-4", "gpk3-5", "gpk3-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 	};
 
-	bt_shutdown: bt-shutdown {
+	bt_shutdown: bt-shutdown-pins {
 		samsung,pins = "gpl0-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 	};
 
-	uart_sel: uart-sel {
+	uart_sel: uart-sel-pins {
 		samsung,pins = "gpl2-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
@@ -775,82 +848,94 @@
 		/* 0 = CP, 1 = AP (serial output) */
 	};
 
-	tsp_rst: tsp-rst {
+	led_bl_reset: led-bl-reset-pins {
+		samsung,pins = "gpm0-1";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	tsp_rst: tsp-rst-pins {
 		samsung,pins = "gpm0-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 	};
 
-	tsp_irq: tsp-irq {
+	lvds_nshdn: lvds-nshdn-pins {
+		samsung,pins = "gpm0-5";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	tsp_irq: tsp-irq-pins {
 		samsung,pins = "gpm2-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 	};
 
-	wifi_reset: wifi-reset {
+	wifi_reset: wifi-reset-pins {
 		samsung,pins = "gpm3-5";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 	};
 
-	tsp_reg_gpio_1: tsp-reg-gpio-1 {
+	tsp_reg_gpio_1: tsp-reg-gpio-1-pins {
 		samsung,pins = "gpm4-5";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 	};
 
-	ak8975_irq: ak8975-irq {
+	ak8975_irq: ak8975-irq-pins {
 		samsung,pins = "gpm4-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
 	};
 
-	stmpe_adc_irq: stmpe-adc-irq {
+	stmpe_adc_irq: stmpe-adc-irq-pins {
 		samsung,pins = "gpx0-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 	};
 
-	max77686_irq: max77686-irq {
+	max77686_irq: max77686-irq-pins {
 		samsung,pins = "gpx0-7";
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 	};
 
-	gpio_keys: gpio-keys {
+	gpio_keys: gpio-keys-pins {
 		samsung,pins = "gpx2-2", "gpx2-7", "gpx3-3";
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 	};
 
-	fuel_alert_irq: fuel-alert-irq {
+	fuel_alert_irq: fuel-alert-irq-pins {
 		samsung,pins = "gpx2-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 	};
 
-	wifi_host_wake: wifi-host-wake {
+	wifi_host_wake: wifi-host-wake-pins {
 		samsung,pins = "gpx2-5";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
 	};
 
-	bt_host_wakeup: bt-host-wakeup {
+	bt_host_wakeup: bt-host-wakeup-pins {
 		samsung,pins = "gpx2-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 	};
 
-	bt_device_wakeup: bt-device-wakeup {
+	bt_device_wakeup: bt-device-wakeup-pins {
 		samsung,pins = "gpx3-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 	};
 
-	sdhci2_cd: sdhci2-cd {
+	sdhci2_cd: sdhci2-cd-pins {
 		samsung,pins = "gpx3-4";
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 	};
 
-	sleep1: sleep-states {
+	sleep1: sleep-state {
 		PIN_SLP(gpk0-0, PREV, NONE);
 		PIN_SLP(gpk0-1, PREV, NONE);
 		PIN_SLP(gpk0-2, PREV, NONE);
@@ -1004,7 +1089,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&sleep2>;
 
-	sleep2: sleep-states {
+	sleep2: sleep-state {
 		PIN_SLP(gpz-0, INPUT, DOWN);
 		PIN_SLP(gpz-1, INPUT, DOWN);
 		PIN_SLP(gpz-2, INPUT, DOWN);
@@ -1019,7 +1104,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&sleep3>;
 
-	sleep3: sleep-states {
+	sleep3: sleep-state {
 		PIN_SLP(gpv0-0, INPUT, DOWN);
 		PIN_SLP(gpv0-1, INPUT, DOWN);
 		PIN_SLP(gpv0-2, INPUT, DOWN);
@@ -1066,6 +1151,13 @@
 	assigned-clock-parents = <&clock CLK_XUSBXTI>;
 };
 
+&pwm {
+	pinctrl-0 = <&pwm1_out>;
+	pinctrl-names = "default";
+	samsung,pwm-outputs = <1>;
+	status = "okay";
+};
+
 &rtc {
 	clocks = <&clock CLK_RTC>, <&max77686 MAX77686_CLK_AP>;
 	clock-names = "rtc", "rtc_src";
diff --git a/arch/arm/boot/dts/exynos4412-pinctrl.dtsi b/arch/arm/boot/dts/exynos4412-pinctrl.dtsi
index d7d5fdc230d8..58847d4fa846 100644
--- a/arch/arm/boot/dts/exynos4412-pinctrl.dtsi
+++ b/arch/arm/boot/dts/exynos4412-pinctrl.dtsi
@@ -9,7 +9,7 @@
  * tree nodes are listed in this file.
  */
 
-#include <dt-bindings/pinctrl/samsung.h>
+#include "exynos-pinctrl.h"
 
 #define PIN_SLP(_pin, _mode, _pull)					\
 	_pin {								\
@@ -19,7 +19,7 @@
 	}
 
 &pinctrl_0 {
-	gpa0: gpa0 {
+	gpa0: gpa0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -27,7 +27,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpa1: gpa1 {
+	gpa1: gpa1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -35,7 +35,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpb: gpb {
+	gpb: gpb-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -43,7 +43,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpc0: gpc0 {
+	gpc0: gpc0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -51,7 +51,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpc1: gpc1 {
+	gpc1: gpc1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -59,7 +59,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpd0: gpd0 {
+	gpd0: gpd0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -67,7 +67,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpd1: gpd1 {
+	gpd1: gpd1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -75,7 +75,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpf0: gpf0 {
+	gpf0: gpf0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -83,7 +83,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpf1: gpf1 {
+	gpf1: gpf1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -91,7 +91,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpf2: gpf2 {
+	gpf2: gpf2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -99,7 +99,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpf3: gpf3 {
+	gpf3: gpf3-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -107,7 +107,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpj0: gpj0 {
+	gpj0: gpj0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -115,7 +115,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpj1: gpj1 {
+	gpj1: gpj1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -123,112 +123,112 @@
 		#interrupt-cells = <2>;
 	};
 
-	uart0_data: uart0-data {
+	uart0_data: uart0-data-pins {
 		samsung,pins = "gpa0-0", "gpa0-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	uart0_fctl: uart0-fctl {
+	uart0_fctl: uart0-fctl-pins {
 		samsung,pins = "gpa0-2", "gpa0-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	uart1_data: uart1-data {
+	uart1_data: uart1-data-pins {
 		samsung,pins = "gpa0-4", "gpa0-5";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	uart1_fctl: uart1-fctl {
+	uart1_fctl: uart1-fctl-pins {
 		samsung,pins = "gpa0-6", "gpa0-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2c2_bus: i2c2-bus {
+	i2c2_bus: i2c2-bus-pins {
 		samsung,pins = "gpa0-6", "gpa0-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	uart2_data: uart2-data {
+	uart2_data: uart2-data-pins {
 		samsung,pins = "gpa1-0", "gpa1-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	uart2_fctl: uart2-fctl {
+	uart2_fctl: uart2-fctl-pins {
 		samsung,pins = "gpa1-2", "gpa1-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	uart_audio_a: uart-audio-a {
+	uart_audio_a: uart-audio-a-pins {
 		samsung,pins = "gpa1-0", "gpa1-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2c3_bus: i2c3-bus {
+	i2c3_bus: i2c3-bus-pins {
 		samsung,pins = "gpa1-2", "gpa1-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	uart3_data: uart3-data {
+	uart3_data: uart3-data-pins {
 		samsung,pins = "gpa1-4", "gpa1-5";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	uart_audio_b: uart-audio-b {
+	uart_audio_b: uart-audio-b-pins {
 		samsung,pins = "gpa1-4", "gpa1-5";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	spi0_bus: spi0-bus {
+	spi0_bus: spi0-bus-pins {
 		samsung,pins = "gpb-0", "gpb-2", "gpb-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2c4_bus: i2c4-bus {
+	i2c4_bus: i2c4-bus-pins {
 		samsung,pins = "gpb-0", "gpb-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	spi1_bus: spi1-bus {
+	spi1_bus: spi1-bus-pins {
 		samsung,pins = "gpb-4", "gpb-6", "gpb-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2c5_bus: i2c5-bus {
+	i2c5_bus: i2c5-bus-pins {
 		samsung,pins = "gpb-2", "gpb-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2s1_bus: i2s1-bus {
+	i2s1_bus: i2s1-bus-pins {
 		samsung,pins = "gpc0-0", "gpc0-1", "gpc0-2", "gpc0-3",
 				"gpc0-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
@@ -236,7 +236,7 @@
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	pcm1_bus: pcm1-bus {
+	pcm1_bus: pcm1-bus-pins {
 		samsung,pins = "gpc0-0", "gpc0-1", "gpc0-2", "gpc0-3",
 				"gpc0-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
@@ -244,7 +244,7 @@
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	ac97_bus: ac97-bus {
+	ac97_bus: ac97-bus-pins {
 		samsung,pins = "gpc0-0", "gpc0-1", "gpc0-2", "gpc0-3",
 				"gpc0-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
@@ -252,7 +252,7 @@
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2s2_bus: i2s2-bus {
+	i2s2_bus: i2s2-bus-pins {
 		samsung,pins = "gpc1-0", "gpc1-1", "gpc1-2", "gpc1-3",
 				"gpc1-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
@@ -260,7 +260,7 @@
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	pcm2_bus: pcm2-bus {
+	pcm2_bus: pcm2-bus-pins {
 		samsung,pins = "gpc1-0", "gpc1-1", "gpc1-2", "gpc1-3",
 				"gpc1-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
@@ -268,105 +268,105 @@
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	spdif_bus: spdif-bus {
+	spdif_bus: spdif-bus-pins {
 		samsung,pins = "gpc1-0", "gpc1-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2c6_bus: i2c6-bus {
+	i2c6_bus: i2c6-bus-pins {
 		samsung,pins = "gpc1-3", "gpc1-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	spi2_bus: spi2-bus {
+	spi2_bus: spi2-bus-pins {
 		samsung,pins = "gpc1-1", "gpc1-3", "gpc1-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_5>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	pwm0_out: pwm0-out {
+	pwm0_out: pwm0-out-pins {
 		samsung,pins = "gpd0-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	pwm1_out: pwm1-out {
+	pwm1_out: pwm1-out-pins {
 		samsung,pins = "gpd0-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	lcd_ctrl: lcd-ctrl {
+	lcd_ctrl: lcd-ctrl-pins {
 		samsung,pins = "gpd0-0", "gpd0-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2c7_bus: i2c7-bus {
+	i2c7_bus: i2c7-bus-pins {
 		samsung,pins = "gpd0-2", "gpd0-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	pwm2_out: pwm2-out {
+	pwm2_out: pwm2-out-pins {
 		samsung,pins = "gpd0-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	pwm3_out: pwm3-out {
+	pwm3_out: pwm3-out-pins {
 		samsung,pins = "gpd0-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2c0_bus: i2c0-bus {
+	i2c0_bus: i2c0-bus-pins {
 		samsung,pins = "gpd1-0", "gpd1-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	mipi0_clk: mipi0-clk {
+	mipi0_clk: mipi0-clk-pins {
 		samsung,pins = "gpd1-0", "gpd1-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2c1_bus: i2c1-bus {
+	i2c1_bus: i2c1-bus-pins {
 		samsung,pins = "gpd1-2", "gpd1-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	mipi1_clk: mipi1-clk {
+	mipi1_clk: mipi1-clk-pins {
 		samsung,pins = "gpd1-2", "gpd1-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	lcd_clk: lcd-clk {
+	lcd_clk: lcd-clk-pins {
 		samsung,pins = "gpf0-0", "gpf0-1", "gpf0-2", "gpf0-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	lcd_data16: lcd-data-width16 {
+	lcd_data16: lcd-data-width16-pins {
 		samsung,pins = "gpf0-7", "gpf1-0", "gpf1-1", "gpf1-2",
 				"gpf1-3", "gpf1-6", "gpf1-7", "gpf2-0",
 				"gpf2-1", "gpf2-2", "gpf2-3", "gpf2-7",
@@ -376,7 +376,7 @@
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	lcd_data18: lcd-data-width18 {
+	lcd_data18: lcd-data-width18-pins {
 		samsung,pins = "gpf0-6", "gpf0-7", "gpf1-0", "gpf1-1",
 				"gpf1-2", "gpf1-3", "gpf1-6", "gpf1-7",
 				"gpf2-0", "gpf2-1", "gpf2-2", "gpf2-3",
@@ -387,7 +387,7 @@
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	lcd_data24: lcd-data-width24 {
+	lcd_data24: lcd-data-width24-pins {
 		samsung,pins = "gpf0-4", "gpf0-5", "gpf0-6", "gpf0-7",
 				"gpf1-0", "gpf1-1", "gpf1-2", "gpf1-3",
 				"gpf1-4", "gpf1-5", "gpf1-6", "gpf1-7",
@@ -399,14 +399,14 @@
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	lcd_ldi: lcd-ldi {
+	lcd_ldi: lcd-ldi-pins {
 		samsung,pins = "gpf3-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	cam_port_a_io: cam-port-a-io {
+	cam_port_a_io: cam-port-a-io-pins {
 		samsung,pins = "gpj0-0", "gpj0-1", "gpj0-2", "gpj0-3",
 				"gpj0-4", "gpj0-5", "gpj0-6", "gpj0-7",
 				"gpj1-0", "gpj1-1", "gpj1-2", "gpj1-4";
@@ -415,14 +415,14 @@
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	cam_port_a_clk_active: cam-port-a-clk-active {
+	cam_port_a_clk_active: cam-port-a-clk-active-pins {
 		samsung,pins = "gpj1-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	cam_port_a_clk_idle: cam-port-a-clk-idle {
+	cam_port_a_clk_idle: cam-port-a-clk-idle-pins {
 		samsung,pins = "gpj1-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
@@ -431,7 +431,7 @@
 };
 
 &pinctrl_1 {
-	gpk0: gpk0 {
+	gpk0: gpk0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -439,7 +439,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpk1: gpk1 {
+	gpk1: gpk1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -447,7 +447,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpk2: gpk2 {
+	gpk2: gpk2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -455,7 +455,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpk3: gpk3 {
+	gpk3: gpk3-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -463,7 +463,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpl0: gpl0 {
+	gpl0: gpl0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -471,7 +471,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpl1: gpl1 {
+	gpl1: gpl1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -479,7 +479,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpl2: gpl2 {
+	gpl2: gpl2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -487,7 +487,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpm0: gpm0 {
+	gpm0: gpm0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -495,7 +495,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpm1: gpm1 {
+	gpm1: gpm1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -503,7 +503,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpm2: gpm2 {
+	gpm2: gpm2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -511,7 +511,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpm3: gpm3 {
+	gpm3: gpm3-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -519,7 +519,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpm4: gpm4 {
+	gpm4: gpm4-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -527,42 +527,42 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpy0: gpy0 {
+	gpy0: gpy0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpy1: gpy1 {
+	gpy1: gpy1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpy2: gpy2 {
+	gpy2: gpy2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpy3: gpy3 {
+	gpy3: gpy3-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpy4: gpy4 {
+	gpy4: gpy4-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpy5: gpy5 {
+	gpy5: gpy5-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpy6: gpy6 {
+	gpy6: gpy6-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpx0: gpx0 {
+	gpx0: gpx0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -579,7 +579,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpx1: gpx1 {
+	gpx1: gpx1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -596,7 +596,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpx2: gpx2 {
+	gpx2: gpx2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -604,7 +604,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpx3: gpx3 {
+	gpx3: gpx3-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -612,203 +612,203 @@
 		#interrupt-cells = <2>;
 	};
 
-	sd0_clk: sd0-clk {
+	sd0_clk: sd0-clk-pins {
 		samsung,pins = "gpk0-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd0_cmd: sd0-cmd {
+	sd0_cmd: sd0-cmd-pins {
 		samsung,pins = "gpk0-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd0_cd: sd0-cd {
+	sd0_cd: sd0-cd-pins {
 		samsung,pins = "gpk0-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd0_bus1: sd0-bus-width1 {
+	sd0_bus1: sd0-bus-width1-pins {
 		samsung,pins = "gpk0-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd0_bus4: sd0-bus-width4 {
+	sd0_bus4: sd0-bus-width4-pins {
 		samsung,pins = "gpk0-3", "gpk0-4", "gpk0-5", "gpk0-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd0_bus8: sd0-bus-width8 {
+	sd0_bus8: sd0-bus-width8-pins {
 		samsung,pins = "gpk1-3", "gpk1-4", "gpk1-5", "gpk1-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd4_clk: sd4-clk {
+	sd4_clk: sd4-clk-pins {
 		samsung,pins = "gpk0-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd4_cmd: sd4-cmd {
+	sd4_cmd: sd4-cmd-pins {
 		samsung,pins = "gpk0-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd4_cd: sd4-cd {
+	sd4_cd: sd4-cd-pins {
 		samsung,pins = "gpk0-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd4_bus1: sd4-bus-width1 {
+	sd4_bus1: sd4-bus-width1-pins {
 		samsung,pins = "gpk0-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd4_bus4: sd4-bus-width4 {
+	sd4_bus4: sd4-bus-width4-pins {
 		samsung,pins = "gpk0-3", "gpk0-4", "gpk0-5", "gpk0-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd4_bus8: sd4-bus-width8 {
+	sd4_bus8: sd4-bus-width8-pins {
 		samsung,pins = "gpk1-3", "gpk1-4", "gpk1-5", "gpk1-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd1_clk: sd1-clk {
+	sd1_clk: sd1-clk-pins {
 		samsung,pins = "gpk1-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd1_cmd: sd1-cmd {
+	sd1_cmd: sd1-cmd-pins {
 		samsung,pins = "gpk1-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd1_cd: sd1-cd {
+	sd1_cd: sd1-cd-pins {
 		samsung,pins = "gpk1-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd1_bus1: sd1-bus-width1 {
+	sd1_bus1: sd1-bus-width1-pins {
 		samsung,pins = "gpk1-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd1_bus4: sd1-bus-width4 {
+	sd1_bus4: sd1-bus-width4-pins {
 		samsung,pins = "gpk1-3", "gpk1-4", "gpk1-5", "gpk1-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd2_clk: sd2-clk {
+	sd2_clk: sd2-clk-pins {
 		samsung,pins = "gpk2-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd2_cmd: sd2-cmd {
+	sd2_cmd: sd2-cmd-pins {
 		samsung,pins = "gpk2-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd2_cd: sd2-cd {
+	sd2_cd: sd2-cd-pins {
 		samsung,pins = "gpk2-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd2_bus1: sd2-bus-width1 {
+	sd2_bus1: sd2-bus-width1-pins {
 		samsung,pins = "gpk2-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd2_bus4: sd2-bus-width4 {
+	sd2_bus4: sd2-bus-width4-pins {
 		samsung,pins = "gpk2-3", "gpk2-4", "gpk2-5", "gpk2-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd2_bus8: sd2-bus-width8 {
+	sd2_bus8: sd2-bus-width8-pins {
 		samsung,pins = "gpk3-3", "gpk3-4", "gpk3-5", "gpk3-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd3_clk: sd3-clk {
+	sd3_clk: sd3-clk-pins {
 		samsung,pins = "gpk3-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd3_cmd: sd3-cmd {
+	sd3_cmd: sd3-cmd-pins {
 		samsung,pins = "gpk3-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd3_cd: sd3-cd {
+	sd3_cd: sd3-cd-pins {
 		samsung,pins = "gpk3-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd3_bus1: sd3-bus-width1 {
+	sd3_bus1: sd3-bus-width1-pins {
 		samsung,pins = "gpk3-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd3_bus4: sd3-bus-width4 {
+	sd3_bus4: sd3-bus-width4-pins {
 		samsung,pins = "gpk3-3", "gpk3-4", "gpk3-5", "gpk3-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	cam_port_b_io: cam-port-b-io {
+	cam_port_b_io: cam-port-b-io-pins {
 		samsung,pins = "gpm0-0", "gpm0-1", "gpm0-2", "gpm0-3",
 				"gpm0-4", "gpm0-5", "gpm0-6", "gpm0-7",
 				"gpm1-0", "gpm1-1", "gpm2-0", "gpm2-1";
@@ -817,77 +817,77 @@
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	cam_port_b_clk_active: cam-port-b-clk-active {
+	cam_port_b_clk_active: cam-port-b-clk-active-pins {
 		samsung,pins = "gpm2-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	cam_port_b_clk_idle: cam-port-b-clk-idle {
+	cam_port_b_clk_idle: cam-port-b-clk-idle-pins {
 		samsung,pins = "gpm2-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	eint0: ext-int0 {
+	eint0: ext-int0-pins {
 		samsung,pins = "gpx0-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	eint8: ext-int8 {
+	eint8: ext-int8-pins {
 		samsung,pins = "gpx1-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	eint15: ext-int15 {
+	eint15: ext-int15-pins {
 		samsung,pins = "gpx1-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	eint16: ext-int16 {
+	eint16: ext-int16-pins {
 		samsung,pins = "gpx2-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	eint31: ext-int31 {
+	eint31: ext-int31-pins {
 		samsung,pins = "gpx3-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	fimc_is_i2c0: fimc-is-i2c0 {
+	fimc_is_i2c0: fimc-is-i2c0-pins {
 		samsung,pins = "gpm4-0", "gpm4-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	fimc_is_i2c1: fimc-is-i2c1 {
+	fimc_is_i2c1: fimc-is-i2c1-pins {
 		samsung,pins = "gpm4-2", "gpm4-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	fimc_is_uart: fimc-is-uart {
+	fimc_is_uart: fimc-is-uart-pins {
 		samsung,pins = "gpm3-5", "gpm3-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	hdmi_cec: hdmi-cec {
+	hdmi_cec: hdmi-cec-pins {
 		samsung,pins = "gpx3-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
@@ -896,7 +896,7 @@
 };
 
 &pinctrl_2 {
-	gpz: gpz {
+	gpz: gpz-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -904,7 +904,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	i2s0_bus: i2s0-bus {
+	i2s0_bus: i2s0-bus-pins {
 		samsung,pins = "gpz-0", "gpz-1", "gpz-2", "gpz-3",
 				"gpz-4", "gpz-5", "gpz-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
@@ -912,7 +912,7 @@
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	pcm0_bus: pcm0-bus {
+	pcm0_bus: pcm0-bus-pins {
 		samsung,pins = "gpz-0", "gpz-1", "gpz-2", "gpz-3",
 				"gpz-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
@@ -922,7 +922,7 @@
 };
 
 &pinctrl_3 {
-	gpv0: gpv0 {
+	gpv0: gpv0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -930,7 +930,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpv1: gpv1 {
+	gpv1: gpv1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -938,7 +938,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpv2: gpv2 {
+	gpv2: gpv2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -946,7 +946,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpv3: gpv3 {
+	gpv3: gpv3-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -954,7 +954,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpv4: gpv4 {
+	gpv4: gpv4-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -962,7 +962,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	c2c_bus: c2c-bus {
+	c2c_bus: c2c-bus-pins {
 		samsung,pins = "gpv0-0", "gpv0-1", "gpv0-2", "gpv0-3",
 				"gpv0-4", "gpv0-5", "gpv0-6", "gpv0-7",
 				"gpv1-0", "gpv1-1", "gpv1-2", "gpv1-3",
diff --git a/arch/arm/boot/dts/exynos4412-smdk4412.dts b/arch/arm/boot/dts/exynos4412-smdk4412.dts
index cc99b955af0c..a40ff394977c 100644
--- a/arch/arm/boot/dts/exynos4412-smdk4412.dts
+++ b/arch/arm/boot/dts/exynos4412-smdk4412.dts
@@ -133,14 +133,14 @@
 };
 
 &pinctrl_1 {
-	keypad_rows: keypad-rows {
+	keypad_rows: keypad-rows-pins {
 		samsung,pins = "gpx2-0", "gpx2-1", "gpx2-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	keypad_cols: keypad-cols {
+	keypad_cols: keypad-cols-pins {
 		samsung,pins = "gpx1-0", "gpx1-1", "gpx1-2", "gpx1-3",
 			       "gpx1-4", "gpx1-5", "gpx1-6", "gpx1-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
diff --git a/arch/arm/boot/dts/exynos4412-tiny4412.dts b/arch/arm/boot/dts/exynos4412-tiny4412.dts
index 017b26108bb0..04388c575efe 100644
--- a/arch/arm/boot/dts/exynos4412-tiny4412.dts
+++ b/arch/arm/boot/dts/exynos4412-tiny4412.dts
@@ -11,6 +11,7 @@
 /dts-v1/;
 #include "exynos4412.dtsi"
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
 
 / {
 	model = "FriendlyARM TINY4412 board based on Exynos4412";
@@ -30,6 +31,7 @@
 
 		led1 {
 			label = "led1";
+			function = LED_FUNCTION_HEARTBEAT;
 			gpios = <&gpm4 0 GPIO_ACTIVE_LOW>;
 			default-state = "off";
 			linux,default-trigger = "heartbeat";
@@ -49,6 +51,7 @@
 
 		led4 {
 			label = "led4";
+			function = LED_FUNCTION_DISK_ACTIVITY;
 			gpios = <&gpm4 3 GPIO_ACTIVE_LOW>;
 			default-state = "off";
 			linux,default-trigger = "mmc0";
diff --git a/arch/arm/boot/dts/exynos4412.dtsi b/arch/arm/boot/dts/exynos4412.dtsi
index d3802046c8b8..aa0b61b59970 100644
--- a/arch/arm/boot/dts/exynos4412.dtsi
+++ b/arch/arm/boot/dts/exynos4412.dtsi
@@ -813,7 +813,7 @@
 	interrupt-parent = <&combiner>;
 	interrupts = <2 4>;
 	reg = <0x100C0000 0x100>;
-	clocks = <&clock 383>;
+	clocks = <&clock CLK_TMU_APBIF>;
 	clock-names = "tmu_apbif";
 	status = "disabled";
 };
diff --git a/arch/arm/boot/dts/exynos5.dtsi b/arch/arm/boot/dts/exynos5.dtsi
index 9ce9fb3fc190..c8da0d4b1b33 100644
--- a/arch/arm/boot/dts/exynos5.dtsi
+++ b/arch/arm/boot/dts/exynos5.dtsi
@@ -89,7 +89,7 @@
 			compatible = "arm,gic-400", "arm,cortex-a15-gic";
 			#interrupt-cells = <3>;
 			interrupt-controller;
-			reg =	<0x10481000 0x1000>,
+			reg = <0x10481000 0x1000>,
 				<0x10482000 0x2000>,
 				<0x10484000 0x2000>,
 				<0x10486000 0x2000>;
diff --git a/arch/arm/boot/dts/exynos5250-arndale.dts b/arch/arm/boot/dts/exynos5250-arndale.dts
index 3583095fbb2a..71c0e87d3a1d 100644
--- a/arch/arm/boot/dts/exynos5250-arndale.dts
+++ b/arch/arm/boot/dts/exynos5250-arndale.dts
@@ -30,42 +30,42 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		menu {
+		key-menu {
 			label = "SW-TACT2";
 			gpios = <&gpx1 4 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_MENU>;
 			wakeup-source;
 		};
 
-		home {
+		key-home {
 			label = "SW-TACT3";
 			gpios = <&gpx1 5 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_HOME>;
 			wakeup-source;
 		};
 
-		up {
+		key-up {
 			label = "SW-TACT4";
 			gpios = <&gpx1 6 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_UP>;
 			wakeup-source;
 		};
 
-		down {
+		key-down {
 			label = "SW-TACT5";
 			gpios = <&gpx1 7 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_DOWN>;
 			wakeup-source;
 		};
 
-		back {
+		key-back {
 			label = "SW-TACT6";
 			gpios = <&gpx2 0 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_BACK>;
 			wakeup-source;
 		};
 
-		wakeup {
+		key-wakeup {
 			label = "SW-TACT7";
 			gpios = <&gpx2 1 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_WAKEUP>;
@@ -590,7 +590,7 @@
 };
 
 &pinctrl_0 {
-	s5m8767_irq: s5m8767-irq {
+	s5m8767_irq: s5m8767-irq-pins {
 		samsung,pins = "gpx3-2";
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 	};
@@ -632,3 +632,8 @@
 		#size-cells = <0>;
 	};
 };
+
+&usbdrd {
+	vdd10-supply = <&ldo15_reg>;
+	vdd33-supply = <&ldo12_reg>;
+};
diff --git a/arch/arm/boot/dts/exynos5250-pinctrl.dtsi b/arch/arm/boot/dts/exynos5250-pinctrl.dtsi
index d31a68672bfa..48732edadff1 100644
--- a/arch/arm/boot/dts/exynos5250-pinctrl.dtsi
+++ b/arch/arm/boot/dts/exynos5250-pinctrl.dtsi
@@ -9,10 +9,10 @@
  * tree nodes are listed in this file.
  */
 
-#include <dt-bindings/pinctrl/samsung.h>
+#include "exynos-pinctrl.h"
 
 &pinctrl_0 {
-	gpa0: gpa0 {
+	gpa0: gpa0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -20,7 +20,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpa1: gpa1 {
+	gpa1: gpa1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -28,7 +28,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpa2: gpa2 {
+	gpa2: gpa2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -36,7 +36,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpb0: gpb0 {
+	gpb0: gpb0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -44,7 +44,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpb1: gpb1 {
+	gpb1: gpb1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -52,7 +52,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpb2: gpb2 {
+	gpb2: gpb2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -60,7 +60,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpb3: gpb3 {
+	gpb3: gpb3-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -68,7 +68,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpc0: gpc0 {
+	gpc0: gpc0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -76,7 +76,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpc1: gpc1 {
+	gpc1: gpc1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -84,7 +84,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpc2: gpc2 {
+	gpc2: gpc2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -92,7 +92,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpc3: gpc3 {
+	gpc3: gpc3-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -100,7 +100,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpd0: gpd0 {
+	gpd0: gpd0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -108,7 +108,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpd1: gpd1 {
+	gpd1: gpd1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -116,42 +116,42 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpy0: gpy0 {
+	gpy0: gpy0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpy1: gpy1 {
+	gpy1: gpy1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpy2: gpy2 {
+	gpy2: gpy2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpy3: gpy3 {
+	gpy3: gpy3-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpy4: gpy4 {
+	gpy4: gpy4-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpy5: gpy5 {
+	gpy5: gpy5-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpy6: gpy6 {
+	gpy6: gpy6-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpc4: gpc4 {
+	gpc4: gpc4-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -159,7 +159,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpx0: gpx0 {
+	gpx0: gpx0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -170,7 +170,7 @@
 			     <26 0>, <26 1>, <27 0>, <27 1>;
 	};
 
-	gpx1: gpx1 {
+	gpx1: gpx1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -181,7 +181,7 @@
 			     <30 0>, <30 1>, <31 0>, <31 1>;
 	};
 
-	gpx2: gpx2 {
+	gpx2: gpx2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -189,7 +189,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpx3: gpx3 {
+	gpx3: gpx3-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -197,104 +197,104 @@
 		#interrupt-cells = <2>;
 	};
 
-	uart0_data: uart0-data {
+	uart0_data: uart0-data-pins {
 		samsung,pins = "gpa0-0", "gpa0-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	uart0_fctl: uart0-fctl {
+	uart0_fctl: uart0-fctl-pins {
 		samsung,pins = "gpa0-2", "gpa0-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2c2_bus: i2c2-bus {
+	i2c2_bus: i2c2-bus-pins {
 		samsung,pins = "gpa0-6", "gpa0-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2c2_hs_bus: i2c2-hs-bus {
+	i2c2_hs_bus: i2c2-hs-bus-pins {
 		samsung,pins = "gpa0-6", "gpa0-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2c2_gpio_bus: i2c2-gpio-bus {
+	i2c2_gpio_bus: i2c2-gpio-bus-pins {
 		samsung,pins = "gpa0-6", "gpa0-7";
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	uart2_data: uart2-data {
+	uart2_data: uart2-data-pins {
 		samsung,pins = "gpa1-0", "gpa1-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	uart2_fctl: uart2-fctl {
+	uart2_fctl: uart2-fctl-pins {
 		samsung,pins = "gpa1-2", "gpa1-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2c3_bus: i2c3-bus {
+	i2c3_bus: i2c3-bus-pins {
 		samsung,pins = "gpa1-2", "gpa1-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2c3_hs_bus: i2c3-hs-bus {
+	i2c3_hs_bus: i2c3-hs-bus-pins {
 		samsung,pins = "gpa1-2", "gpa1-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	uart3_data: uart3-data {
-		samsung,pins = "gpa1-4", "gpa1-4";
+	uart3_data: uart3-data-pins {
+		samsung,pins = "gpa1-4", "gpa1-5";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	spi0_bus: spi0-bus {
+	spi0_bus: spi0-bus-pins {
 		samsung,pins = "gpa2-0", "gpa2-2", "gpa2-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2c4_bus: i2c4-bus {
+	i2c4_bus: i2c4-bus-pins {
 		samsung,pins = "gpa2-0", "gpa2-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2c5_bus: i2c5-bus {
+	i2c5_bus: i2c5-bus-pins {
 		samsung,pins = "gpa2-2", "gpa2-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	spi1_bus: spi1-bus {
+	spi1_bus: spi1-bus-pins {
 		samsung,pins = "gpa2-4", "gpa2-6", "gpa2-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2s1_bus: i2s1-bus {
+	i2s1_bus: i2s1-bus-pins {
 		samsung,pins = "gpb0-0", "gpb0-1", "gpb0-2", "gpb0-3",
 			       "gpb0-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
@@ -302,7 +302,7 @@
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	pcm1_bus: pcm1-bus {
+	pcm1_bus: pcm1-bus-pins {
 		samsung,pins = "gpb0-0", "gpb0-1", "gpb0-2", "gpb0-3",
 			       "gpb0-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
@@ -310,7 +310,7 @@
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	ac97_bus: ac97-bus {
+	ac97_bus: ac97-bus-pins {
 		samsung,pins = "gpb0-0", "gpb0-1", "gpb0-2", "gpb0-3",
 			       "gpb0-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
@@ -318,7 +318,7 @@
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2s2_bus: i2s2-bus {
+	i2s2_bus: i2s2-bus-pins {
 		samsung,pins = "gpb1-0", "gpb1-1", "gpb1-2", "gpb1-3",
 			       "gpb1-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
@@ -326,7 +326,7 @@
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	pcm2_bus: pcm2-bus {
+	pcm2_bus: pcm2-bus-pins {
 		samsung,pins = "gpb1-0", "gpb1-1", "gpb1-2", "gpb1-3",
 			       "gpb1-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
@@ -334,280 +334,280 @@
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	spdif_bus: spdif-bus {
+	spdif_bus: spdif-bus-pins {
 		samsung,pins = "gpb1-0", "gpb1-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	spi2_bus: spi2-bus {
+	spi2_bus: spi2-bus-pins {
 		samsung,pins = "gpb1-1", "gpb1-3", "gpb1-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_5>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2c6_bus: i2c6-bus {
+	i2c6_bus: i2c6-bus-pins {
 		samsung,pins = "gpb1-3", "gpb1-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	pwm0_out: pwm0-out {
+	pwm0_out: pwm0-out-pins {
 		samsung,pins = "gpb2-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	pwm1_out: pwm1-out {
+	pwm1_out: pwm1-out-pins {
 		samsung,pins = "gpb2-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	pwm2_out: pwm2-out {
+	pwm2_out: pwm2-out-pins {
 		samsung,pins = "gpb2-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	pwm3_out: pwm3-out {
+	pwm3_out: pwm3-out-pins {
 		samsung,pins = "gpb2-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2c7_bus: i2c7-bus {
+	i2c7_bus: i2c7-bus-pins {
 		samsung,pins = "gpb2-2", "gpb2-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2c0_bus: i2c0-bus {
+	i2c0_bus: i2c0-bus-pins {
 		samsung,pins = "gpb3-0", "gpb3-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2c1_bus: i2c1-bus {
+	i2c1_bus: i2c1-bus-pins {
 		samsung,pins = "gpb3-2", "gpb3-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2c0_hs_bus: i2c0-hs-bus {
+	i2c0_hs_bus: i2c0-hs-bus-pins {
 		samsung,pins = "gpb3-0", "gpb3-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	i2c1_hs_bus: i2c1-hs-bus {
+	i2c1_hs_bus: i2c1-hs-bus-pins {
 		samsung,pins = "gpb3-2", "gpb3-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	sd0_clk: sd0-clk {
+	sd0_clk: sd0-clk-pins {
 		samsung,pins = "gpc0-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd0_cmd: sd0-cmd {
+	sd0_cmd: sd0-cmd-pins {
 		samsung,pins = "gpc0-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd0_cd: sd0-cd {
+	sd0_cd: sd0-cd-pins {
 		samsung,pins = "gpc0-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd0_bus1: sd0-bus-width1 {
+	sd0_bus1: sd0-bus-width1-pins {
 		samsung,pins = "gpc0-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd0_bus4: sd0-bus-width4 {
+	sd0_bus4: sd0-bus-width4-pins {
 		samsung,pins = "gpc0-3", "gpc0-4", "gpc0-5", "gpc0-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd0_bus8: sd0-bus-width8 {
+	sd0_bus8: sd0-bus-width8-pins {
 		samsung,pins = "gpc1-0", "gpc1-1", "gpc1-2", "gpc1-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd1_clk: sd1-clk {
+	sd1_clk: sd1-clk-pins {
 		samsung,pins = "gpc2-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd1_cmd: sd1-cmd {
+	sd1_cmd: sd1-cmd-pins {
 		samsung,pins = "gpc2-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd1_cd: sd1-cd {
+	sd1_cd: sd1-cd-pins {
 		samsung,pins = "gpc2-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd1_bus1: sd1-bus-width1 {
+	sd1_bus1: sd1-bus-width1-pins {
 		samsung,pins = "gpc2-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd1_bus4: sd1-bus-width4 {
+	sd1_bus4: sd1-bus-width4-pins {
 		samsung,pins = "gpc2-3", "gpc2-4", "gpc2-5", "gpc2-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd2_clk: sd2-clk {
+	sd2_clk: sd2-clk-pins {
 		samsung,pins = "gpc3-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd2_cmd: sd2-cmd {
+	sd2_cmd: sd2-cmd-pins {
 		samsung,pins = "gpc3-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd2_cd: sd2-cd {
+	sd2_cd: sd2-cd-pins {
 		samsung,pins = "gpc3-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd2_bus1: sd2-bus-width1 {
+	sd2_bus1: sd2-bus-width1-pins {
 		samsung,pins = "gpc3-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd2_bus4: sd2-bus-width4 {
+	sd2_bus4: sd2-bus-width4-pins {
 		samsung,pins = "gpc3-3", "gpc3-4", "gpc3-5", "gpc3-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd2_bus8: sd2-bus-width8 {
+	sd2_bus8: sd2-bus-width8-pins {
 		samsung,pins = "gpc4-3", "gpc4-4", "gpc4-5", "gpc4-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd3_clk: sd3-clk {
+	sd3_clk: sd3-clk-pins {
 		samsung,pins = "gpc4-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd3_cmd: sd3-cmd {
+	sd3_cmd: sd3-cmd-pins {
 		samsung,pins = "gpc4-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd3_cd: sd3-cd {
+	sd3_cd: sd3-cd-pins {
 		samsung,pins = "gpc4-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd3_bus1: sd3-bus-width1 {
+	sd3_bus1: sd3-bus-width1-pins {
 		samsung,pins = "gpc4-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	sd3_bus4: sd3-bus-width4 {
+	sd3_bus4: sd3-bus-width4-pins {
 		samsung,pins = "gpc4-3", "gpc4-4", "gpc4-5", "gpc4-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
 	};
 
-	uart1_data: uart1-data {
+	uart1_data: uart1-data-pins {
 		samsung,pins = "gpd0-0", "gpd0-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	uart1_fctl: uart1-fctl {
+	uart1_fctl: uart1-fctl-pins {
 		samsung,pins = "gpd0-2", "gpd0-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	dp_hpd: dp_hpd {
+	dp_hpd: dp-hpd-pins {
 		samsung,pins = "gpx0-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	hdmi_cec: hdmi-cec {
+	hdmi_cec: hdmi-cec-pins {
 		samsung,pins = "gpx3-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	hdmi_hpd: hdmi-hpd {
+	hdmi_hpd: hdmi-hpd-pins {
 		samsung,pins = "gpx3-7";
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 	};
 };
 
 &pinctrl_1 {
-	gpe0: gpe0 {
+	gpe0: gpe0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -615,7 +615,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpe1: gpe1 {
+	gpe1: gpe1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -623,7 +623,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpf0: gpf0 {
+	gpf0: gpf0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -631,7 +631,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpf1: gpf1 {
+	gpf1: gpf1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -639,7 +639,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpg0: gpg0 {
+	gpg0: gpg0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -647,7 +647,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpg1: gpg1 {
+	gpg1: gpg1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -655,7 +655,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpg2: gpg2 {
+	gpg2: gpg2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -663,7 +663,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gph0: gph0 {
+	gph0: gph0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -671,7 +671,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gph1: gph1 {
+	gph1: gph1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -679,7 +679,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	cam_gpio_a: cam-gpio-a {
+	cam_gpio_a: cam-gpio-a-pins {
 		samsung,pins = "gpe0-0", "gpe0-1", "gpe0-2", "gpe0-3",
 			       "gpe0-4", "gpe0-5", "gpe0-6", "gpe0-7",
 			       "gpe1-0", "gpe1-1";
@@ -688,7 +688,7 @@
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	cam_gpio_b: cam-gpio-b {
+	cam_gpio_b: cam-gpio-b-pins {
 		samsung,pins = "gpf0-0", "gpf0-1", "gpf0-2", "gpf0-3",
 			       "gpf1-0", "gpf1-1", "gpf1-2", "gpf1-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
@@ -696,42 +696,42 @@
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	cam_i2c2_bus: cam-i2c2-bus {
+	cam_i2c2_bus: cam-i2c2-bus-pins {
 		samsung,pins = "gpe0-6", "gpe1-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	cam_spi1_bus: cam-spi1-bus {
+	cam_spi1_bus: cam-spi1-bus-pins {
 		samsung,pins = "gpe0-4", "gpe0-5", "gpf0-2", "gpf0-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	cam_i2c1_bus: cam-i2c1-bus {
+	cam_i2c1_bus: cam-i2c1-bus-pins {
 		samsung,pins = "gpf0-2", "gpf0-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	cam_i2c0_bus: cam-i2c0-bus {
+	cam_i2c0_bus: cam-i2c0-bus-pins {
 		samsung,pins = "gpf0-0", "gpf0-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	cam_spi0_bus: cam-spi0-bus {
+	cam_spi0_bus: cam-spi0-bus-pins {
 		samsung,pins = "gpf1-0", "gpf1-1", "gpf1-2", "gpf1-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	cam_bayrgb_bus: cam-bayrgb-bus {
+	cam_bayrgb_bus: cam-bayrgb-bus-pins {
 		samsung,pins = "gpg0-0", "gpg0-1", "gpg0-2", "gpg0-3",
 			       "gpg0-4", "gpg0-5", "gpg0-6", "gpg0-7",
 			       "gpg1-0", "gpg1-1", "gpg1-2", "gpg1-3",
@@ -742,7 +742,7 @@
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	cam_port_a: cam-port-a {
+	cam_port_a: cam-port-a-pins {
 		samsung,pins = "gph0-0", "gph0-1", "gph0-2", "gph0-3",
 			       "gph1-0", "gph1-1", "gph1-2", "gph1-3",
 			       "gph1-4", "gph1-5", "gph1-6", "gph1-7";
@@ -753,7 +753,7 @@
 };
 
 &pinctrl_2 {
-	gpv0: gpv0 {
+	gpv0: gpv0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -761,7 +761,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpv1: gpv1 {
+	gpv1: gpv1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -769,7 +769,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpv2: gpv2 {
+	gpv2: gpv2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -777,7 +777,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpv3: gpv3 {
+	gpv3: gpv3-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -785,7 +785,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpv4: gpv4 {
+	gpv4: gpv4-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -793,7 +793,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	c2c_rxd: c2c-rxd {
+	c2c_rxd: c2c-rxd-pins {
 		samsung,pins = "gpv0-0", "gpv0-1", "gpv0-2", "gpv0-3",
 			       "gpv0-4", "gpv0-5", "gpv0-6", "gpv0-7",
 			       "gpv1-0", "gpv1-1", "gpv1-2", "gpv1-3",
@@ -803,7 +803,7 @@
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	c2c_txd: c2c-txd {
+	c2c_txd: c2c-txd-pins {
 		samsung,pins = "gpv2-0", "gpv2-1", "gpv2-2", "gpv2-3",
 			       "gpv2-4", "gpv2-5", "gpv2-6", "gpv2-7",
 			       "gpv3-0", "gpv3-1", "gpv3-2", "gpv3-3",
@@ -815,7 +815,7 @@
 };
 
 &pinctrl_3 {
-	gpz: gpz {
+	gpz: gpz-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -823,7 +823,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	i2s0_bus: i2s0-bus {
+	i2s0_bus: i2s0-bus-pins {
 		samsung,pins = "gpz-0", "gpz-1", "gpz-2", "gpz-3",
 				"gpz-4", "gpz-5", "gpz-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
diff --git a/arch/arm/boot/dts/exynos5250-smdk5250.dts b/arch/arm/boot/dts/exynos5250-smdk5250.dts
index 39bbe18145cf..71293749ac48 100644
--- a/arch/arm/boot/dts/exynos5250-smdk5250.dts
+++ b/arch/arm/boot/dts/exynos5250-smdk5250.dts
@@ -118,6 +118,9 @@
 	status = "okay";
 	ddc = <&i2c_2>;
 	hpd-gpios = <&gpx3 7 GPIO_ACTIVE_HIGH>;
+	vdd-supply = <&ldo8_reg>;
+	vdd_osc-supply = <&ldo10_reg>;
+	vdd_pll-supply = <&ldo8_reg>;
 };
 
 &i2c_0 {
@@ -126,7 +129,7 @@
 	samsung,i2c-max-bus-freq = <20000>;
 
 	eeprom@50 {
-		compatible = "samsung,s524ad0xd1";
+		compatible = "samsung,s524ad0xd1", "atmel,24c128";
 		reg = <0x50>;
 	};
 
@@ -286,7 +289,7 @@
 	samsung,i2c-max-bus-freq = <20000>;
 
 	eeprom@51 {
-		compatible = "samsung,s524ad0xd1";
+		compatible = "samsung,s524ad0xd1", "atmel,24c128";
 		reg = <0x51>;
 	};
 
@@ -410,10 +413,15 @@
 };
 
 &pinctrl_0 {
-	max77686_irq: max77686-irq {
+	max77686_irq: max77686-irq-pins {
 		samsung,pins = "gpx3-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 };
+
+&usbdrd {
+	vdd10-supply = <&ldo15_reg>;
+	vdd33-supply = <&ldo12_reg>;
+};
diff --git a/arch/arm/boot/dts/exynos5250-snow-common.dtsi b/arch/arm/boot/dts/exynos5250-snow-common.dtsi
index 2335c4687349..3d84b9c6dea3 100644
--- a/arch/arm/boot/dts/exynos5250-snow-common.dtsi
+++ b/arch/arm/boot/dts/exynos5250-snow-common.dtsi
@@ -32,7 +32,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&power_key_irq &lid_irq>;
 
-		power {
+		power-key {
 			label = "Power";
 			gpios = <&gpx1 3 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
@@ -587,63 +587,63 @@
 };
 
 &pinctrl_0 {
-	wifi_en: wifi-en {
+	wifi_en: wifi-en-pins {
 		samsung,pins = "gpx0-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	wifi_rst: wifi-rst {
+	wifi_rst: wifi-rst-pins {
 		samsung,pins = "gpx0-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	power_key_irq: power-key-irq {
+	power_key_irq: power-key-irq-pins {
 		samsung,pins = "gpx1-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	ec_irq: ec-irq {
+	ec_irq: ec-irq-pins {
 		samsung,pins = "gpx1-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	tps65090_irq: tps65090-irq {
+	tps65090_irq: tps65090-irq-pins {
 		samsung,pins = "gpx2-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	usb3_vbus_en: usb3-vbus-en {
+	usb3_vbus_en: usb3-vbus-en-pins {
 		samsung,pins = "gpx2-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	max77686_irq: max77686-irq {
+	max77686_irq: max77686-irq-pins {
 		samsung,pins = "gpx3-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	lid_irq: lid-irq {
+	lid_irq: lid-irq-pins {
 		samsung,pins = "gpx3-5";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	hdmi_hpd_irq: hdmi-hpd-irq {
+	hdmi_hpd_irq: hdmi-hpd-irq-pins {
 		samsung,pins = "gpx3-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
@@ -652,14 +652,14 @@
 };
 
 &pinctrl_1 {
-	arb_their_claim: arb-their-claim {
+	arb_their_claim: arb-their-claim-pins {
 		samsung,pins = "gpe0-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	arb_our_claim: arb-our-claim {
+	arb_our_claim: arb-our-claim-pins {
 		samsung,pins = "gpf0-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
@@ -698,6 +698,11 @@
 	cs-gpios = <&gpa2 5 GPIO_ACTIVE_HIGH>;
 };
 
+&usbdrd {
+	vdd10-supply = <&ldo15_reg>;
+	vdd33-supply = <&ldo12_reg>;
+};
+
 &usbdrd_dwc3 {
 	dr_mode = "host";
 };
diff --git a/arch/arm/boot/dts/exynos5250-snow-rev5.dts b/arch/arm/boot/dts/exynos5250-snow-rev5.dts
index f8ca61df6981..0a47597d6f0d 100644
--- a/arch/arm/boot/dts/exynos5250-snow-rev5.dts
+++ b/arch/arm/boot/dts/exynos5250-snow-rev5.dts
@@ -47,7 +47,7 @@
 };
 
 &pinctrl_0 {
-	max98090_irq: max98090-irq {
+	max98090_irq: max98090-irq-pins {
 		samsung,pins = "gpx0-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
diff --git a/arch/arm/boot/dts/exynos5250-snow.dts b/arch/arm/boot/dts/exynos5250-snow.dts
index a630bc654a49..906aa7aae710 100644
--- a/arch/arm/boot/dts/exynos5250-snow.dts
+++ b/arch/arm/boot/dts/exynos5250-snow.dts
@@ -43,7 +43,7 @@
 };
 
 &pinctrl_0 {
-	max98095_en: max98095-en {
+	max98095_en: max98095-en-pins {
 		samsung,pins = "gpx1-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
diff --git a/arch/arm/boot/dts/exynos5250-spring.dts b/arch/arm/boot/dts/exynos5250-spring.dts
index e0feedcf54bb..5eca10ecd550 100644
--- a/arch/arm/boot/dts/exynos5250-spring.dts
+++ b/arch/arm/boot/dts/exynos5250-spring.dts
@@ -33,7 +33,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&power_key_irq>, <&lid_irq>;
 
-		power {
+		power-key {
 			label = "Power";
 			gpios = <&gpx1 3 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
@@ -451,63 +451,63 @@
 };
 
 &pinctrl_0 {
-	s5m8767_dvs: s5m8767-dvs {
+	s5m8767_dvs: s5m8767-dvs-pins {
 		samsung,pins = "gpd1-0", "gpd1-1", "gpd1-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	dp_hpd_gpio: dp-hpd {
+	dp_hpd_gpio: dp-hpd-pins {
 		samsung,pins = "gpc3-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	trackpad_irq: trackpad-irq {
+	trackpad_irq: trackpad-irq-pins {
 		samsung,pins = "gpx1-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	power_key_irq: power-key-irq {
+	power_key_irq: power-key-irq-pins {
 		samsung,pins = "gpx1-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	ec_irq: ec-irq {
+	ec_irq: ec-irq-pins {
 		samsung,pins = "gpx1-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	s5m8767_ds: s5m8767-ds {
+	s5m8767_ds: s5m8767-ds-pins {
 		samsung,pins = "gpx2-3", "gpx2-4", "gpx2-5";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	s5m8767_irq: s5m8767-irq {
+	s5m8767_irq: s5m8767-irq-pins {
 		samsung,pins = "gpx3-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	lid_irq: lid-irq {
+	lid_irq: lid-irq-pins {
 		samsung,pins = "gpx3-5";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
 	};
 
-	hdmi_hpd_irq: hdmi-hpd-irq {
+	hdmi_hpd_irq: hdmi-hpd-irq-pins {
 		samsung,pins = "gpx3-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
@@ -516,7 +516,7 @@
 };
 
 &pinctrl_1 {
-	hsic_reset: hsic-reset {
+	hsic_reset: hsic-reset-pins {
 		samsung,pins = "gpe1-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
@@ -553,4 +553,9 @@
 	num-cs = <1>;
 };
 
+&usbdrd {
+	vdd10-supply = <&ldo15_reg>;
+	vdd33-supply = <&ldo12_reg>;
+};
+
 #include "cros-ec-keyboard.dtsi"
diff --git a/arch/arm/boot/dts/exynos5250.dtsi b/arch/arm/boot/dts/exynos5250.dtsi
index 139778928b93..4708dcd575a7 100644
--- a/arch/arm/boot/dts/exynos5250.dtsi
+++ b/arch/arm/boot/dts/exynos5250.dtsi
@@ -245,7 +245,8 @@
 		};
 
 		timer@101c0000 {
-			compatible = "samsung,exynos4210-mct";
+			compatible = "samsung,exynos5250-mct",
+				     "samsung,exynos4210-mct";
 			reg = <0x101C0000 0x800>;
 			clocks = <&clock CLK_FIN_PLL>, <&clock CLK_MCT>;
 			clock-names = "fin_pll", "mct";
@@ -496,8 +497,7 @@
 			status = "disabled";
 			reg = <0x12d20000 0x100>;
 			interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>;
-			dmas = <&pdma0 5
-				&pdma0 4>;
+			dmas = <&pdma0 5>, <&pdma0 4>;
 			dma-names = "tx", "rx";
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -512,8 +512,7 @@
 			status = "disabled";
 			reg = <0x12d30000 0x100>;
 			interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>;
-			dmas = <&pdma1 5
-				&pdma1 4>;
+			dmas = <&pdma1 5>, <&pdma1 4>;
 			dma-names = "tx", "rx";
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -528,8 +527,7 @@
 			status = "disabled";
 			reg = <0x12d40000 0x100>;
 			interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>;
-			dmas = <&pdma0 7
-				&pdma0 6>;
+			dmas = <&pdma0 7>, <&pdma0 6>;
 			dma-names = "tx", "rx";
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -637,7 +635,7 @@
 			#sound-dai-cells = <1>;
 		};
 
-		usb_dwc3 {
+		usbdrd: usb3 {
 			compatible = "samsung,exynos5250-dwusb3";
 			clocks = <&clock CLK_USB3>;
 			clock-names = "usbdrd30";
@@ -695,48 +693,40 @@
 			samsung,pmureg-phandle = <&pmu_system_controller>;
 		};
 
-		pdma0: pdma@121a0000 {
+		pdma0: dma-controller@121a0000 {
 			compatible = "arm,pl330", "arm,primecell";
 			reg = <0x121A0000 0x1000>;
 			interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&clock CLK_PDMA0>;
 			clock-names = "apb_pclk";
 			#dma-cells = <1>;
-			#dma-channels = <8>;
-			#dma-requests = <32>;
 		};
 
-		pdma1: pdma@121b0000 {
+		pdma1: dma-controller@121b0000 {
 			compatible = "arm,pl330", "arm,primecell";
 			reg = <0x121B0000 0x1000>;
 			interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&clock CLK_PDMA1>;
 			clock-names = "apb_pclk";
 			#dma-cells = <1>;
-			#dma-channels = <8>;
-			#dma-requests = <32>;
 		};
 
-		mdma0: mdma@10800000 {
+		mdma0: dma-controller@10800000 {
 			compatible = "arm,pl330", "arm,primecell";
 			reg = <0x10800000 0x1000>;
 			interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&clock CLK_MDMA0>;
 			clock-names = "apb_pclk";
 			#dma-cells = <1>;
-			#dma-channels = <8>;
-			#dma-requests = <1>;
 		};
 
-		mdma1: mdma@11c10000 {
+		mdma1: dma-controller@11c10000 {
 			compatible = "arm,pl330", "arm,primecell";
 			reg = <0x11C10000 0x1000>;
 			interrupts = <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&clock CLK_MDMA1>;
 			clock-names = "apb_pclk";
 			#dma-cells = <1>;
-			#dma-channels = <8>;
-			#dma-requests = <1>;
 		};
 
 		gsc_0: gsc@13e00000 {
@@ -820,15 +810,14 @@
 			status = "disabled";
 		};
 
-		dp_phy: video-phy {
+		dp_phy: video-phy-0 {
 			compatible = "samsung,exynos5250-dp-video-phy";
 			samsung,pmu-syscon = <&pmu_system_controller>;
 			#phy-cells = <0>;
 		};
 
-		mipi_phy: video-phy@10040710 {
+		mipi_phy: video-phy-1 {
 			compatible = "samsung,s5pv210-mipi-video-phy";
-			reg = <0x10040710 0x100>;
 			#phy-cells = <1>;
 			syscon = <&pmu_system_controller>;
 		};
diff --git a/arch/arm/boot/dts/exynos5260-pinctrl.dtsi b/arch/arm/boot/dts/exynos5260-pinctrl.dtsi
index 17e2f3e0d71e..43e4a541f479 100644
--- a/arch/arm/boot/dts/exynos5260-pinctrl.dtsi
+++ b/arch/arm/boot/dts/exynos5260-pinctrl.dtsi
@@ -9,10 +9,10 @@
  * tree nodes are listed in this file.
  */
 
-#include <dt-bindings/pinctrl/samsung.h>
+#include "exynos-pinctrl.h"
 
 &pinctrl_0 {
-	gpa0: gpa0 {
+	gpa0: gpa0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -20,7 +20,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpa1: gpa1 {
+	gpa1: gpa1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -28,7 +28,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpa2: gpa2 {
+	gpa2: gpa2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -36,7 +36,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpb0: gpb0 {
+	gpb0: gpb0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -44,7 +44,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpb1: gpb1 {
+	gpb1: gpb1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -52,7 +52,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpb2: gpb2 {
+	gpb2: gpb2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -60,7 +60,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpb3: gpb3 {
+	gpb3: gpb3-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -68,7 +68,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpb4: gpb4 {
+	gpb4: gpb4-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -76,7 +76,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpb5: gpb5 {
+	gpb5: gpb5-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -84,7 +84,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpd0: gpd0 {
+	gpd0: gpd0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -92,7 +92,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpd1: gpd1 {
+	gpd1: gpd1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -100,7 +100,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpd2: gpd2 {
+	gpd2: gpd2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -108,7 +108,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpe0: gpe0 {
+	gpe0: gpe0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -116,7 +116,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpe1: gpe1 {
+	gpe1: gpe1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -124,7 +124,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpf0: gpf0 {
+	gpf0: gpf0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -132,7 +132,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpf1: gpf1 {
+	gpf1: gpf1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -140,7 +140,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpk0: gpk0 {
+	gpk0: gpk0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -148,7 +148,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpx0: gpx0 {
+	gpx0: gpx0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -164,7 +164,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpx1: gpx1 {
+	gpx1: gpx1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -180,7 +180,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpx2: gpx2 {
+	gpx2: gpx2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -188,7 +188,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpx3: gpx3 {
+	gpx3: gpx3-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -196,63 +196,63 @@
 		#interrupt-cells = <2>;
 	};
 
-	uart0_data: uart0-data {
+	uart0_data: uart0-data-pins {
 		samsung,pins = "gpa0-0", "gpa0-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV1>;
 	};
 
-	uart0_fctl: uart0-fctl {
+	uart0_fctl: uart0-fctl-pins {
 		samsung,pins = "gpa0-2", "gpa0-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV1>;
 	};
 
-	uart1_data: uart1-data {
+	uart1_data: uart1-data-pins {
 		samsung,pins = "gpa1-0", "gpa1-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV1>;
 	};
 
-	uart1_fctl: uart1-fctl {
+	uart1_fctl: uart1-fctl-pins {
 		samsung,pins = "gpa1-2", "gpa1-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV1>;
 	};
 
-	uart2_data: uart2-data {
+	uart2_data: uart2-data-pins {
 		samsung,pins = "gpa1-4", "gpa1-5";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV1>;
 	};
 
-	spi0_bus: spi0-bus {
+	spi0_bus: spi0-bus-pins {
 		samsung,pins = "gpa2-0", "gpa2-2", "gpa2-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV1>;
 	};
 
-	spi1_bus: spi1-bus {
+	spi1_bus: spi1-bus-pins {
 		samsung,pins = "gpa2-4", "gpa2-6", "gpa2-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV1>;
 	};
 
-	usb3_vbus0_en: usb3-vbus0-en {
+	usb3_vbus0_en: usb3-vbus0-en-pins {
 		samsung,pins = "gpa2-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV1>;
 	};
 
-	i2s1_bus: i2s1-bus {
+	i2s1_bus: i2s1-bus-pins {
 		samsung,pins = "gpb0-0", "gpb0-1", "gpb0-2", "gpb0-3",
 				"gpb0-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
@@ -260,7 +260,7 @@
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV1>;
 	};
 
-	pcm1_bus: pcm1-bus {
+	pcm1_bus: pcm1-bus-pins {
 		samsung,pins = "gpb0-0", "gpb0-1", "gpb0-2", "gpb0-3",
 				"gpb0-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
@@ -268,105 +268,105 @@
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV1>;
 	};
 
-	spdif1_bus: spdif1-bus {
+	spdif1_bus: spdif1-bus-pins {
 		samsung,pins = "gpb0-0", "gpb0-1", "gpb0-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV1>;
 	};
 
-	spi2_bus: spi2-bus {
+	spi2_bus: spi2-bus-pins {
 		samsung,pins = "gpb1-0", "gpb1-2", "gpb1-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV1>;
 	};
 
-	i2c0_hs_bus: i2c0-hs-bus {
+	i2c0_hs_bus: i2c0-hs-bus-pins {
 		samsung,pins = "gpb3-0", "gpb3-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV1>;
 	};
 
-	i2c1_hs_bus: i2c1-hs-bus {
+	i2c1_hs_bus: i2c1-hs-bus-pins {
 		samsung,pins = "gpb3-2", "gpb3-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV1>;
 	};
 
-	i2c2_hs_bus: i2c2-hs-bus {
+	i2c2_hs_bus: i2c2-hs-bus-pins {
 		samsung,pins = "gpb3-4", "gpb3-5";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV1>;
 	};
 
-	i2c3_hs_bus: i2c3-hs-bus {
+	i2c3_hs_bus: i2c3-hs-bus-pins {
 		samsung,pins = "gpb3-6", "gpb3-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV1>;
 	};
 
-	i2c4_bus: i2c4-bus {
+	i2c4_bus: i2c4-bus-pins {
 		samsung,pins = "gpb4-0", "gpb4-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV1>;
 	};
 
-	i2c5_bus: i2c5-bus {
+	i2c5_bus: i2c5-bus-pins {
 		samsung,pins = "gpb4-2", "gpb4-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV1>;
 	};
 
-	i2c6_bus: i2c6-bus {
+	i2c6_bus: i2c6-bus-pins {
 		samsung,pins = "gpb4-4", "gpb4-5";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV1>;
 	};
 
-	i2c7_bus: i2c7-bus {
+	i2c7_bus: i2c7-bus-pins {
 		samsung,pins = "gpb4-6", "gpb4-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV1>;
 	};
 
-	i2c8_bus: i2c8-bus {
+	i2c8_bus: i2c8-bus-pins {
 		samsung,pins = "gpb5-0", "gpb5-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV1>;
 	};
 
-	i2c9_bus: i2c9-bus {
+	i2c9_bus: i2c9-bus-pins {
 		samsung,pins = "gpb5-2", "gpb5-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV1>;
 	};
 
-	i2c10_bus: i2c10-bus {
+	i2c10_bus: i2c10-bus-pins {
 		samsung,pins = "gpb5-4", "gpb5-5";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV1>;
 	};
 
-	i2c11_bus: i2c11-bus {
+	i2c11_bus: i2c11-bus-pins {
 		samsung,pins = "gpb5-6", "gpb5-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV1>;
 	};
 
-	cam_gpio_a: cam-gpio-a {
+	cam_gpio_a: cam-gpio-a-pins {
 		samsung,pins = "gpe0-0", "gpe0-1", "gpe0-2", "gpe0-3",
 			"gpe0-4", "gpe0-5", "gpe0-6", "gpe0-7",
 			"gpe1-0", "gpe1-1";
@@ -375,7 +375,7 @@
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV1>;
 	};
 
-	cam_gpio_b: cam-gpio-b {
+	cam_gpio_b: cam-gpio-b-pins {
 		samsung,pins = "gpf0-0", "gpf0-1", "gpf0-2", "gpf0-3",
 			"gpf1-0", "gpf1-1", "gpf1-2", "gpf1-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
@@ -383,28 +383,28 @@
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV1>;
 	};
 
-	cam_i2c1_bus: cam-i2c1-bus {
+	cam_i2c1_bus: cam-i2c1-bus-pins {
 		samsung,pins = "gpf0-2", "gpf0-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV1>;
 	};
 
-	cam_i2c0_bus: cam-i2c0-bus {
+	cam_i2c0_bus: cam-i2c0-bus-pins {
 		samsung,pins = "gpf0-0", "gpf0-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV1>;
 	};
 
-	cam_spi0_bus: cam-spi0-bus {
+	cam_spi0_bus: cam-spi0-bus-pins {
 		samsung,pins = "gpf1-0", "gpf1-1", "gpf1-2", "gpf1-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV1>;
 	};
 
-	cam_spi1_bus: cam-spi1-bus {
+	cam_spi1_bus: cam-spi1-bus-pins {
 		samsung,pins = "gpf1-4", "gpf1-5", "gpf1-6", "gpf1-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
@@ -413,7 +413,7 @@
 };
 
 &pinctrl_1 {
-	gpc0: gpc0 {
+	gpc0: gpc0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -421,7 +421,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpc1: gpc1 {
+	gpc1: gpc1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -429,7 +429,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpc2: gpc2 {
+	gpc2: gpc2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -437,7 +437,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpc3: gpc3 {
+	gpc3: gpc3-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -445,7 +445,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpc4: gpc4 {
+	gpc4: gpc4-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -453,112 +453,112 @@
 		#interrupt-cells = <2>;
 	};
 
-	sd0_clk: sd0-clk {
+	sd0_clk: sd0-clk-pins {
 		samsung,pins = "gpc0-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV6>;
 	};
 
-	sd0_cmd: sd0-cmd {
+	sd0_cmd: sd0-cmd-pins {
 		samsung,pins = "gpc0-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV6>;
 	};
 
-	sd0_bus1: sd0-bus-width1 {
+	sd0_bus1: sd0-bus-width1-pins {
 		samsung,pins = "gpc0-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV6>;
 	};
 
-	sd0_bus4: sd0-bus-width4 {
+	sd0_bus4: sd0-bus-width4-pins {
 		samsung,pins = "gpc0-3", "gpc0-4", "gpc0-5";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV6>;
 	};
 
-	sd0_bus8: sd0-bus-width8 {
+	sd0_bus8: sd0-bus-width8-pins {
 		samsung,pins = "gpc3-0", "gpc3-1", "gpc3-2", "gpc3-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV6>;
 	};
 
-	sd0_rdqs: sd0-rdqs {
+	sd0_rdqs: sd0-rdqs-pins {
 		samsung,pins = "gpc0-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV6>;
 	};
 
-	sd1_clk: sd1-clk {
+	sd1_clk: sd1-clk-pins {
 		samsung,pins = "gpc1-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV6>;
 	};
 
-	sd1_cmd: sd1-cmd {
+	sd1_cmd: sd1-cmd-pins {
 		samsung,pins = "gpc1-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV6>;
 	};
 
-	sd1_bus1: sd1-bus-width1 {
+	sd1_bus1: sd1-bus-width1-pins {
 		samsung,pins = "gpc1-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV6>;
 	};
 
-	sd1_bus4: sd1-bus-width4 {
+	sd1_bus4: sd1-bus-width4-pins {
 		samsung,pins = "gpc1-3", "gpc1-4", "gpc1-5";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV6>;
 	};
 
-	sd1_bus8: sd1-bus-width8 {
+	sd1_bus8: sd1-bus-width8-pins {
 		samsung,pins = "gpc4-0", "gpc4-1", "gpc4-2", "gpc4-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV6>;
 	};
 
-	sd2_clk: sd2-clk {
+	sd2_clk: sd2-clk-pins {
 		samsung,pins = "gpc2-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV6>;
 	};
 
-	sd2_cmd: sd2-cmd {
+	sd2_cmd: sd2-cmd-pins {
 		samsung,pins = "gpc2-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV6>;
 	};
 
-	sd2_cd: sd2-cd {
+	sd2_cd: sd2-cd-pins {
 		samsung,pins = "gpc2-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV6>;
 	};
 
-	sd2_bus1: sd2-bus-width1 {
+	sd2_bus1: sd2-bus-width1-pins {
 		samsung,pins = "gpc2-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5260_PIN_DRV_LV6>;
 	};
 
-	sd2_bus4: sd2-bus-width4 {
+	sd2_bus4: sd2-bus-width4-pins {
 		samsung,pins = "gpc2-4", "gpc2-5", "gpc2-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
@@ -567,7 +567,7 @@
 };
 
 &pinctrl_2 {
-	gpz0: gpz0 {
+	gpz0: gpz0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -575,7 +575,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpz1: gpz1 {
+	gpz1: gpz1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
diff --git a/arch/arm/boot/dts/exynos5260-xyref5260.dts b/arch/arm/boot/dts/exynos5260-xyref5260.dts
index 0dc2ec16aa0a..3c3b751d4360 100644
--- a/arch/arm/boot/dts/exynos5260-xyref5260.dts
+++ b/arch/arm/boot/dts/exynos5260-xyref5260.dts
@@ -29,6 +29,27 @@
 		#clock-cells = <0>;
 	};
 
+	ioclk_pcm: clock-pcm-ext {
+		compatible = "fixed-clock";
+		clock-frequency = <2048000>;
+		clock-output-names = "ioclk_pcm_extclk";
+		#clock-cells = <0>;
+	};
+
+	ioclk_i2s: clock-i2s-cd {
+		compatible = "fixed-clock";
+		clock-frequency = <147456000>;
+		clock-output-names = "ioclk_i2s_cdclk";
+		#clock-cells = <0>;
+	};
+
+	ioclk_spdif: clock-spdif-ext {
+		compatible = "fixed-clock";
+		clock-frequency = <49152000>;
+		clock-output-names = "ioclk_spdif_extclk";
+		#clock-cells = <0>;
+	};
+
 	xrtcxti: xrtcxti {
 		compatible = "fixed-clock";
 		clock-frequency = <32768>;
@@ -38,7 +59,7 @@
 };
 
 &pinctrl_0 {
-	hdmi_hpd_irq: hdmi-hpd-irq {
+	hdmi_hpd_irq: hdmi-hpd-irq-pins {
 		samsung,pins = "gpx3-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
diff --git a/arch/arm/boot/dts/exynos5260.dtsi b/arch/arm/boot/dts/exynos5260.dtsi
index 52fa211525ce..ff1ee409eff3 100644
--- a/arch/arm/boot/dts/exynos5260.dtsi
+++ b/arch/arm/boot/dts/exynos5260.dtsi
@@ -113,78 +113,206 @@
 			compatible = "samsung,exynos5260-clock-top";
 			reg = <0x10010000 0x10000>;
 			#clock-cells = <1>;
+			clocks = <&fin_pll>,
+				 <&clock_mif MIF_DOUT_MEM_PLL>,
+				 <&clock_mif MIF_DOUT_BUS_PLL>,
+				 <&clock_mif MIF_DOUT_MEDIA_PLL>;
+			clock-names = "fin_pll",
+				      "dout_mem_pll",
+				      "dout_bus_pll",
+				      "dout_media_pll";
 		};
 
 		clock_peri: clock-controller@10200000 {
 			compatible = "samsung,exynos5260-clock-peri";
 			reg = <0x10200000 0x10000>;
 			#clock-cells = <1>;
+			clocks = <&fin_pll>,
+				 <&ioclk_pcm>,
+				 <&ioclk_i2s>,
+				 <&ioclk_spdif>,
+				 <&fin_pll>,
+				 <&clock_top TOP_DOUT_ACLK_PERI_66>,
+				 <&clock_top TOP_DOUT_SCLK_PERI_UART0>,
+				 <&clock_top TOP_DOUT_SCLK_PERI_UART1>,
+				 <&clock_top TOP_DOUT_SCLK_PERI_UART2>,
+				 <&clock_top TOP_DOUT_SCLK_PERI_SPI0_B>,
+				 <&clock_top TOP_DOUT_SCLK_PERI_SPI1_B>,
+				 <&clock_top TOP_DOUT_SCLK_PERI_SPI2_B>,
+				 <&clock_top TOP_DOUT_ACLK_PERI_AUD>;
+			clock-names = "fin_pll",
+				      "ioclk_pcm_extclk",
+				      "ioclk_i2s_cdclk",
+				      "ioclk_spdif_extclk",
+				      "phyclk_hdmi_phy_ref_cko",
+				      "dout_aclk_peri_66",
+				      "dout_sclk_peri_uart0",
+				      "dout_sclk_peri_uart1",
+				      "dout_sclk_peri_uart2",
+				      "dout_sclk_peri_spi0_b",
+				      "dout_sclk_peri_spi1_b",
+				      "dout_sclk_peri_spi2_b",
+				      "dout_aclk_peri_aud";
 		};
 
 		clock_egl: clock-controller@10600000 {
 			compatible = "samsung,exynos5260-clock-egl";
 			reg = <0x10600000 0x10000>;
 			#clock-cells = <1>;
+			clocks = <&fin_pll>,
+				 <&clock_mif MIF_DOUT_BUS_PLL>;
+			clock-names = "fin_pll",
+				      "dout_bus_pll";
 		};
 
 		clock_kfc: clock-controller@10700000 {
 			compatible = "samsung,exynos5260-clock-kfc";
 			reg = <0x10700000 0x10000>;
 			#clock-cells = <1>;
+			clocks = <&fin_pll>,
+				 <&clock_mif MIF_DOUT_MEDIA_PLL>;
+			clock-names = "fin_pll",
+				      "dout_media_pll";
 		};
 
 		clock_g2d: clock-controller@10a00000 {
 			compatible = "samsung,exynos5260-clock-g2d";
 			reg = <0x10A00000 0x10000>;
 			#clock-cells = <1>;
+			clocks = <&fin_pll>,
+				 <&clock_top TOP_DOUT_ACLK_G2D_333>;
+			clock-names = "fin_pll",
+				      "dout_aclk_g2d_333";
 		};
 
 		clock_mif: clock-controller@10ce0000 {
 			compatible = "samsung,exynos5260-clock-mif";
 			reg = <0x10CE0000 0x10000>;
 			#clock-cells = <1>;
+			clocks = <&fin_pll>;
+			clock-names = "fin_pll";
 		};
 
 		clock_mfc: clock-controller@11090000 {
 			compatible = "samsung,exynos5260-clock-mfc";
 			reg = <0x11090000 0x10000>;
 			#clock-cells = <1>;
+			clocks = <&fin_pll>,
+				 <&clock_top TOP_DOUT_ACLK_MFC_333>;
+			clock-names = "fin_pll",
+				      "dout_aclk_mfc_333";
 		};
 
 		clock_g3d: clock-controller@11830000 {
 			compatible = "samsung,exynos5260-clock-g3d";
 			reg = <0x11830000 0x10000>;
 			#clock-cells = <1>;
+			clocks = <&fin_pll>;
+			clock-names = "fin_pll";
 		};
 
 		clock_fsys: clock-controller@122e0000 {
 			compatible = "samsung,exynos5260-clock-fsys";
 			reg = <0x122E0000 0x10000>;
 			#clock-cells = <1>;
+			clocks = <&fin_pll>,
+				 <&fin_pll>,
+				 <&fin_pll>,
+				 <&fin_pll>,
+				 <&fin_pll>,
+				 <&fin_pll>,
+				 <&clock_top TOP_DOUT_ACLK_FSYS_200>;
+			clock-names = "fin_pll",
+				      "phyclk_usbhost20_phy_phyclock",
+				      "phyclk_usbhost20_phy_freeclk",
+				      "phyclk_usbhost20_phy_clk48mohci",
+				      "phyclk_usbdrd30_udrd30_pipe_pclk",
+				      "phyclk_usbdrd30_udrd30_phyclock",
+				      "dout_aclk_fsys_200";
 		};
 
 		clock_aud: clock-controller@128c0000 {
 			compatible = "samsung,exynos5260-clock-aud";
 			reg = <0x128C0000 0x10000>;
 			#clock-cells = <1>;
+			clocks = <&fin_pll>,
+				 <&clock_top TOP_FOUT_AUD_PLL>,
+				 <&ioclk_i2s>,
+				 <&ioclk_pcm>;
+			clock-names = "fin_pll",
+				      "fout_aud_pll",
+				      "ioclk_i2s_cdclk",
+				      "ioclk_pcm_extclk";
 		};
 
 		clock_isp: clock-controller@133c0000 {
 			compatible = "samsung,exynos5260-clock-isp";
 			reg = <0x133C0000 0x10000>;
 			#clock-cells = <1>;
+			clocks = <&fin_pll>,
+				 <&clock_top TOP_DOUT_ACLK_ISP1_266>,
+				 <&clock_top TOP_DOUT_ACLK_ISP1_400>,
+				 <&clock_top TOP_MOUT_ACLK_ISP1_266>;
+			clock-names = "fin_pll",
+				      "dout_aclk_isp1_266",
+				      "dout_aclk_isp1_400",
+				      "mout_aclk_isp1_266";
 		};
 
 		clock_gscl: clock-controller@13f00000 {
 			compatible = "samsung,exynos5260-clock-gscl";
 			reg = <0x13F00000 0x10000>;
 			#clock-cells = <1>;
+			clocks = <&fin_pll>,
+				 <&clock_top TOP_DOUT_ACLK_GSCL_400>,
+				 <&clock_top TOP_DOUT_ACLK_GSCL_333>;
+			clock-names = "fin_pll",
+				      "dout_aclk_gscl_400",
+				      "dout_aclk_gscl_333";
 		};
 
 		clock_disp: clock-controller@14550000 {
 			compatible = "samsung,exynos5260-clock-disp";
 			reg = <0x14550000 0x10000>;
 			#clock-cells = <1>;
+			clocks = <&fin_pll>,
+				 <&fin_pll>,
+				 <&fin_pll>,
+				 <&fin_pll>,
+				 <&fin_pll>,
+				 <&fin_pll>,
+				 <&fin_pll>,
+				 <&fin_pll>,
+				 <&fin_pll>,
+				 <&fin_pll>,
+				 <&fin_pll>,
+				 <&fin_pll>,
+				 <&fin_pll>,
+				 <&fin_pll>,
+				 <&ioclk_spdif>,
+				 <&clock_top TOP_DOUT_ACLK_PERI_AUD>,
+				 <&clock_top TOP_DOUT_ACLK_DISP_222>,
+				 <&clock_top TOP_DOUT_SCLK_DISP_PIXEL>,
+				 <&clock_top TOP_DOUT_ACLK_DISP_333>;
+			clock-names = "fin_pll",
+				      "phyclk_dptx_phy_ch3_txd_clk",
+				      "phyclk_dptx_phy_ch2_txd_clk",
+				      "phyclk_dptx_phy_ch1_txd_clk",
+				      "phyclk_dptx_phy_ch0_txd_clk",
+				      "phyclk_hdmi_phy_tmds_clko",
+				      "phyclk_hdmi_phy_ref_clko",
+				      "phyclk_hdmi_phy_pixel_clko",
+				      "phyclk_hdmi_link_o_tmds_clkhi",
+				      "phyclk_mipi_dphy_4l_m_txbyte_clkhs",
+				      "phyclk_dptx_phy_o_ref_clk_24m",
+				      "phyclk_dptx_phy_clk_div2",
+				      "phyclk_mipi_dphy_4l_m_rxclkesc0",
+				      "phyclk_hdmi_phy_ref_cko",
+				      "ioclk_spdif_extclk",
+				      "dout_aclk_peri_aud",
+				      "dout_aclk_disp_222",
+				      "dout_sclk_disp_pixel",
+				      "dout_aclk_disp_333";
 		};
 
 		gic: interrupt-controller@10481000 {
@@ -205,7 +333,8 @@
 		};
 
 		mct: timer@100b0000 {
-			compatible = "samsung,exynos4210-mct";
+			compatible = "samsung,exynos5260-mct",
+				     "samsung,exynos4210-mct";
 			reg = <0x100B0000 0x1000>;
 			clocks = <&fin_pll>, <&clock_peri PERI_CLK_MCT>;
 			clock-names = "fin_pll", "mct";
@@ -368,7 +497,7 @@
 			status = "disabled";
 		};
 
-		hsi2c_0: hsi2c@12da0000 {
+		hsi2c_0: i2c@12da0000 {
 			compatible = "samsung,exynos5260-hsi2c";
 			reg = <0x12DA0000 0x1000>;
 			interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
@@ -381,7 +510,7 @@
 			status = "disabled";
 		};
 
-		hsi2c_1: hsi2c@12db0000 {
+		hsi2c_1: i2c@12db0000 {
 			compatible = "samsung,exynos5260-hsi2c";
 			reg = <0x12DB0000 0x1000>;
 			interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
@@ -394,7 +523,7 @@
 			status = "disabled";
 		};
 
-		hsi2c_2: hsi2c@12dc0000 {
+		hsi2c_2: i2c@12dc0000 {
 			compatible = "samsung,exynos5260-hsi2c";
 			reg = <0x12DC0000 0x1000>;
 			interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
@@ -407,7 +536,7 @@
 			status = "disabled";
 		};
 
-		hsi2c_3: hsi2c@12dd0000 {
+		hsi2c_3: i2c@12dd0000 {
 			compatible = "samsung,exynos5260-hsi2c";
 			reg = <0x12DD0000 0x1000>;
 			interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
diff --git a/arch/arm/boot/dts/exynos5410-odroidxu.dts b/arch/arm/boot/dts/exynos5410-odroidxu.dts
index 884fef55836c..d1cbc6b8a570 100644
--- a/arch/arm/boot/dts/exynos5410-odroidxu.dts
+++ b/arch/arm/boot/dts/exynos5410-odroidxu.dts
@@ -188,8 +188,7 @@
 		interrupt-parent = <&gpx0>;
 		interrupts = <4 IRQ_TYPE_NONE>;
 		pinctrl-names = "default";
-		pinctrl-0 = <&max77802_irq>, <&pmic_dvs_1>, <&pmic_dvs_2>,
-			    <&pmic_dvs_3>;
+		pinctrl-0 = <&max77802_irq>, <&pmic_dvs_1>, <&pmic_dvs_2>;
 		wakeup-source;
 		#clock-cells = <1>;
 
@@ -394,10 +393,6 @@
 				regulator-always-on;
 			};
 
-			ldo16_reg: LDO16 {
-				regulator-name = "ldo16";
-			};
-
 			ldo17_reg: LDO17 {
 				regulator-name = "cam_sensor_core";
 				regulator-min-microvolt = <1200000>;
@@ -427,10 +422,6 @@
 				regulator-max-microvolt = <2850000>;
 			};
 
-			ldo22_reg: LDO22 {
-				regulator-name = "ldo22";
-			};
-
 			ldo23_reg: LDO23 {
 				regulator-name = "dp_p3v3";
 				regulator-min-microvolt = <3300000>;
@@ -477,10 +468,6 @@
 				regulator-always-on;
 			};
 
-			ldo31_reg: LDO31 {
-				regulator-name = "ldo31";
-			};
-
 			/* On revisions with ti,ina231 this is sensor VS */
 			ldo32_reg: LDO32 {
 				regulator-name = "vs_power_meter";
@@ -548,14 +535,14 @@
 };
 
 &pinctrl_0 {
-	emmc_nrst_pin: emmc-nrst {
+	emmc_nrst_pin: emmc-nrst-pins {
 		samsung,pins = "gpd1-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	sd2_wp: sd2-wp {
+	sd2_wp: sd2-wp-pins {
 		samsung,pins = "gpm5-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		/* Pin is floating so be sure to disable write-protect */
@@ -563,21 +550,14 @@
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
 	};
 
-	pmic_dvs_3: pmic-dvs-3 {
-		samsung,pins = "gpx0-0";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
-		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
-	};
-
-	pmic_dvs_2: pmic-dvs-2 {
-		samsung,pins = "gpx0-1";
+	pmic_dvs_2: pmic-dvs-2-pins {
+		samsung,pins = "gpx0-0", "gpx0-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	pmic_dvs_1: pmic-dvs-1 {
+	pmic_dvs_1: pmic-dvs-1-pins {
 		samsung,pins = "gpx0-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
@@ -585,7 +565,7 @@
 		samsung,pin-val = <1>;
 	};
 
-	max77802_irq: max77802-irq {
+	max77802_irq: max77802-irq-pins {
 		samsung,pins = "gpx0-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
@@ -675,8 +655,8 @@
 	#address-cells = <1>;
 	#size-cells = <0>;
 
-	ethernet: usbether@2 {
-		compatible = "usb0424,9730";
+	ethernet: ethernet@2 {
+		compatible = "usb424,9730";
 		reg = <2>;
 		local-mac-address = [00 00 00 00 00 00]; /* Filled in by a bootloader */
 	};
diff --git a/arch/arm/boot/dts/exynos5410-pinctrl.dtsi b/arch/arm/boot/dts/exynos5410-pinctrl.dtsi
index 9599ba8ba798..f7b923382892 100644
--- a/arch/arm/boot/dts/exynos5410-pinctrl.dtsi
+++ b/arch/arm/boot/dts/exynos5410-pinctrl.dtsi
@@ -6,10 +6,10 @@
  *              https://www.hardkernel.com
  */
 
-#include <dt-bindings/pinctrl/samsung.h>
+#include "exynos-pinctrl.h"
 
 &pinctrl_0 {
-	gpa0: gpa0 {
+	gpa0: gpa0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -17,7 +17,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpa1: gpa1 {
+	gpa1: gpa1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -25,7 +25,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpa2: gpa2 {
+	gpa2: gpa2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -33,7 +33,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpb0: gpb0 {
+	gpb0: gpb0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -41,7 +41,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpb1: gpb1 {
+	gpb1: gpb1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -49,7 +49,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpb2: gpb2 {
+	gpb2: gpb2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -57,7 +57,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpb3: gpb3 {
+	gpb3: gpb3-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -65,7 +65,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpc0: gpc0 {
+	gpc0: gpc0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -73,7 +73,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpc3: gpc3 {
+	gpc3: gpc3-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -81,7 +81,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpc1: gpc1 {
+	gpc1: gpc1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -89,7 +89,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpc2: gpc2 {
+	gpc2: gpc2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -97,12 +97,12 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpm5: gpm5 {
+	gpm5: gpm5-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpd1: gpd1 {
+	gpd1: gpd1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -110,7 +110,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpe0: gpe0 {
+	gpe0: gpe0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -118,7 +118,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpe1: gpe1 {
+	gpe1: gpe1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -126,7 +126,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpf0: gpf0 {
+	gpf0: gpf0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -134,7 +134,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpf1: gpf1 {
+	gpf1: gpf1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -142,7 +142,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpg0: gpg0 {
+	gpg0: gpg0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -150,7 +150,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpg1: gpg1 {
+	gpg1: gpg1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -158,7 +158,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpg2: gpg2 {
+	gpg2: gpg2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -166,7 +166,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gph0: gph0 {
+	gph0: gph0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -174,7 +174,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gph1: gph1 {
+	gph1: gph1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -182,52 +182,52 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpm7: gpm7 {
+	gpm7: gpm7-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpy0: gpy0 {
+	gpy0: gpy0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpy1: gpy1 {
+	gpy1: gpy1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpy2: gpy2 {
+	gpy2: gpy2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpy3: gpy3 {
+	gpy3: gpy3-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpy4: gpy4 {
+	gpy4: gpy4-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpy5: gpy5 {
+	gpy5: gpy5-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpy6: gpy6 {
+	gpy6: gpy6-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpy7: gpy7 {
+	gpy7: gpy7-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpx0: gpx0 {
+	gpx0: gpx0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -244,7 +244,7 @@
 			     <27 1>;
 	};
 
-	gpx1: gpx1 {
+	gpx1: gpx1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -261,7 +261,7 @@
 			     <31 1>;
 	};
 
-	gpx2: gpx2 {
+	gpx2: gpx2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -269,7 +269,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpx3: gpx3 {
+	gpx3: gpx3-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -277,210 +277,210 @@
 		#interrupt-cells = <2>;
 	};
 
-	uart0_data: uart0-data {
+	uart0_data: uart0-data-pins {
 		samsung,pins = "gpa0-0", "gpa0-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	uart0_fctl: uart0-fctl {
+	uart0_fctl: uart0-fctl-pins {
 		samsung,pins = "gpa0-2", "gpa0-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	uart1_data: uart1-data {
+	uart1_data: uart1-data-pins {
 		samsung,pins = "gpa0-4", "gpa0-5";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	uart1_fctl: uart1-fctl {
+	uart1_fctl: uart1-fctl-pins {
 		samsung,pins = "gpa0-6", "gpa0-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	i2c2_bus: i2c2-bus {
+	i2c2_bus: i2c2-bus-pins {
 		samsung,pins = "gpa0-6", "gpa0-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	uart2_data: uart2-data {
+	uart2_data: uart2-data-pins {
 		samsung,pins = "gpa1-0", "gpa1-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	uart2_fctl: uart2-fctl {
+	uart2_fctl: uart2-fctl-pins {
 		samsung,pins = "gpa1-2", "gpa1-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	i2c3_bus: i2c3-bus {
+	i2c3_bus: i2c3-bus-pins {
 		samsung,pins = "gpa1-2", "gpa1-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	uart3_data: uart3-data {
+	uart3_data: uart3-data-pins {
 		samsung,pins = "gpa1-4", "gpa1-5";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	i2c4_hs_bus: i2c4-hs-bus {
+	i2c4_hs_bus: i2c4-hs-bus-pins {
 		samsung,pins = "gpa2-0", "gpa2-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	i2c5_hs_bus: i2c5-hs-bus {
+	i2c5_hs_bus: i2c5-hs-bus-pins {
 		samsung,pins = "gpa2-2", "gpa2-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	i2c6_hs_bus: i2c6-hs-bus {
+	i2c6_hs_bus: i2c6-hs-bus-pins {
 		samsung,pins = "gpb1-3", "gpb1-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	pwm0_out: pwm0-out {
+	pwm0_out: pwm0-out-pins {
 		samsung,pins = "gpb2-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	pwm1_out: pwm1-out {
+	pwm1_out: pwm1-out-pins {
 		samsung,pins = "gpb2-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	pwm2_out: pwm2-out {
+	pwm2_out: pwm2-out-pins {
 		samsung,pins = "gpb2-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	pwm3_out: pwm3-out {
+	pwm3_out: pwm3-out-pins {
 		samsung,pins = "gpb2-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	i2c7_hs_bus: i2c7-hs-bus {
+	i2c7_hs_bus: i2c7-hs-bus-pins {
 		samsung,pins = "gpb2-2", "gpb2-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	i2c0_bus: i2c0-bus {
+	i2c0_bus: i2c0-bus-pins {
 		samsung,pins = "gpb3-0", "gpb3-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	i2c1_bus: i2c1-bus {
+	i2c1_bus: i2c1-bus-pins {
 		samsung,pins = "gpb3-2", "gpb3-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	sd0_clk: sd0-clk {
+	sd0_clk: sd0-clk-pins {
 		samsung,pins = "gpc0-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
 	};
 
-	sd0_cmd: sd0-cmd {
+	sd0_cmd: sd0-cmd-pins {
 		samsung,pins = "gpc0-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
 	};
 
-	sd0_cd: sd0-cd {
+	sd0_cd: sd0-cd-pins {
 		samsung,pins = "gpc0-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
 	};
 
-	sd0_bus1: sd0-bus-width1 {
+	sd0_bus1: sd0-bus-width1-pins {
 		samsung,pins = "gpc0-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
 	};
 
-	sd0_bus4: sd0-bus-width4 {
+	sd0_bus4: sd0-bus-width4-pins {
 		samsung,pins = "gpc0-4", "gpc0-5", "gpc0-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
 	};
 
-	sd2_clk: sd2-clk {
+	sd2_clk: sd2-clk-pins {
 		samsung,pins = "gpc2-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
 	};
 
-	sd2_cmd: sd2-cmd {
+	sd2_cmd: sd2-cmd-pins {
 		samsung,pins = "gpc2-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
 	};
 
-	sd2_cd: sd2-cd {
+	sd2_cd: sd2-cd-pins {
 		samsung,pins = "gpc2-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
 	};
 
-	sd2_bus1: sd2-bus-width1 {
+	sd2_bus1: sd2-bus-width1-pins {
 		samsung,pins = "gpc2-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
 	};
 
-	sd2_bus4: sd2-bus-width4 {
+	sd2_bus4: sd2-bus-width4-pins {
 		samsung,pins = "gpc2-4", "gpc2-5", "gpc2-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
 	};
 
-	sd0_bus8: sd0-bus-width8 {
+	sd0_bus8: sd0-bus-width8-pins {
 		samsung,pins = "gpc3-0", "gpc3-1", "gpc3-2", "gpc3-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
@@ -489,7 +489,7 @@
 };
 
 &pinctrl_1 {
-	gpj0: gpj0 {
+	gpj0: gpj0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -497,7 +497,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpj1: gpj1 {
+	gpj1: gpj1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -505,7 +505,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpj2: gpj2 {
+	gpj2: gpj2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -513,7 +513,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpj3: gpj3 {
+	gpj3: gpj3-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -521,7 +521,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpj4: gpj4 {
+	gpj4: gpj4-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -529,7 +529,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpk0: gpk0 {
+	gpk0: gpk0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -537,7 +537,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpk1: gpk1 {
+	gpk1: gpk1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -545,7 +545,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpk2: gpk2 {
+	gpk2: gpk2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -553,7 +553,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpk3: gpk3 {
+	gpk3: gpk3-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -561,28 +561,28 @@
 		#interrupt-cells = <2>;
 	};
 
-	usb3_1_oc: usb3-1-oc {
+	usb3_1_oc: usb3-1-oc-pins {
 		samsung,pins = "gpk2-4", "gpk2-5";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	usb3_1_vbusctrl: usb3-1-vbusctrl {
+	usb3_1_vbusctrl: usb3-1-vbusctrl-pins {
 		samsung,pins = "gpk2-6", "gpk2-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	usb3_0_oc: usb3-0-oc {
+	usb3_0_oc: usb3-0-oc-pins {
 		samsung,pins = "gpk3-0", "gpk3-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	usb3_0_vbusctrl: usb3-0-vbusctrl {
+	usb3_0_vbusctrl: usb3-0-vbusctrl-pins {
 		samsung,pins = "gpk3-2", "gpk3-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
@@ -591,7 +591,7 @@
 };
 
 &pinctrl_2 {
-	gpv0: gpv0 {
+	gpv0: gpv0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -599,7 +599,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpv1: gpv1 {
+	gpv1: gpv1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -607,7 +607,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpv2: gpv2 {
+	gpv2: gpv2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -615,7 +615,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpv3: gpv3 {
+	gpv3: gpv3-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -623,7 +623,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpv4: gpv4 {
+	gpv4: gpv4-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -633,7 +633,7 @@
 };
 
 &pinctrl_3 {
-	gpz: gpz {
+	gpz: gpz-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -641,7 +641,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	audi2s0_bus: audi2s0-bus {
+	audi2s0_bus: audi2s0-bus-pins {
 		samsung,pins = "gpz-0", "gpz-1", "gpz-2", "gpz-3",
 				"gpz-4";
 		samsung,pin-function = <2>;
diff --git a/arch/arm/boot/dts/exynos5410-smdk5410.dts b/arch/arm/boot/dts/exynos5410-smdk5410.dts
index 2a3ade77a2de..b8f953c41c73 100644
--- a/arch/arm/boot/dts/exynos5410-smdk5410.dts
+++ b/arch/arm/boot/dts/exynos5410-smdk5410.dts
@@ -41,6 +41,19 @@
 		reg = <0x02037000 0x1000>;
 	};
 
+	vdd10_usb3: voltage-regulator-0 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDD10_USB3";
+		regulator-min-microvolt = <1000000>;
+		regulator-max-microvolt = <1000000>;
+	};
+
+	vdd33_usb3: voltage-regulator-0 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDD33_USB3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
 };
 
 &mmc_0 {
@@ -66,14 +79,14 @@
 };
 
 &pinctrl_0 {
-	srom_ctl: srom-ctl {
+	srom_ctl: srom-ctl-pins {
 		samsung,pins = "gpy0-3", "gpy0-4", "gpy0-5",
 			       "gpy1-0", "gpy1-1", "gpy1-2", "gpy1-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	srom_ebi: srom-ebi {
+	srom_ebi: srom-ebi-pins {
 		samsung,pins = "gpy3-0", "gpy3-1", "gpy3-2", "gpy3-3",
 			       "gpy3-4", "gpy3-5", "gpy3-6", "gpy3-7",
 			       "gpy5-0", "gpy5-1", "gpy5-2", "gpy5-3",
@@ -121,3 +134,13 @@
 &serial_2 {
 	status = "okay";
 };
+
+&usbdrd3_0 {
+	vdd10-supply = <&vdd10_usb3>;
+	vdd33-supply = <&vdd33_usb3>;
+};
+
+&usbdrd3_1 {
+	vdd10-supply = <&vdd10_usb3>;
+	vdd33-supply = <&vdd33_usb3>;
+};
diff --git a/arch/arm/boot/dts/exynos5410.dtsi b/arch/arm/boot/dts/exynos5410.dtsi
index 584ce62361b1..8a6b890fb8f7 100644
--- a/arch/arm/boot/dts/exynos5410.dtsi
+++ b/arch/arm/boot/dts/exynos5410.dtsi
@@ -189,26 +189,22 @@
 			interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>;
 		};
 
-		pdma0: pdma@121a0000 {
+		pdma0: dma-controller@121a0000 {
 			compatible = "arm,pl330", "arm,primecell";
 			reg = <0x121a0000 0x1000>;
 			interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&clock CLK_PDMA0>;
 			clock-names = "apb_pclk";
 			#dma-cells = <1>;
-			#dma-channels = <8>;
-			#dma-requests = <32>;
 		};
 
-		pdma1: pdma@121b0000 {
+		pdma1: dma-controller@121b0000 {
 			compatible = "arm,pl330", "arm,primecell";
 			reg = <0x121b0000 0x1000>;
 			interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&clock CLK_PDMA1>;
 			clock-names = "apb_pclk";
 			#dma-cells = <1>;
-			#dma-channels = <8>;
-			#dma-requests = <32>;
 		};
 
 		audi2s0: i2s@3830000 {
diff --git a/arch/arm/boot/dts/exynos5420-arndale-octa.dts b/arch/arm/boot/dts/exynos5420-arndale-octa.dts
index dfc7f14f5772..55b7759682a9 100644
--- a/arch/arm/boot/dts/exynos5420-arndale-octa.dts
+++ b/arch/arm/boot/dts/exynos5420-arndale-octa.dts
@@ -42,7 +42,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		wakeup {
+		key-wakeup {
 			label = "SW-TACT1";
 			gpios = <&gpx2 7 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_WAKEUP>;
@@ -808,7 +808,7 @@
 };
 
 &pinctrl_0 {
-	s2mps11_irq: s2mps11-irq {
+	s2mps11_irq: s2mps11-irq-pins {
 		samsung,pins = "gpx3-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
@@ -825,3 +825,13 @@
 &usbdrd_dwc3_1 {
 	dr_mode = "host";
 };
+
+&usbdrd3_0 {
+	vdd10-supply = <&ldo11_reg>;
+	vdd33-supply = <&ldo9_reg>;
+};
+
+&usbdrd3_1 {
+	vdd10-supply = <&ldo11_reg>;
+	vdd33-supply = <&ldo9_reg>;
+};
diff --git a/arch/arm/boot/dts/exynos5420-chagall-wifi.dts b/arch/arm/boot/dts/exynos5420-chagall-wifi.dts
new file mode 100644
index 000000000000..1319344a2c74
--- /dev/null
+++ b/arch/arm/boot/dts/exynos5420-chagall-wifi.dts
@@ -0,0 +1,75 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Samsung's Exynos5420 Chagall WiFi board device tree source
+ *
+ * Copyright (c) 2012-2013 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
+ * Copyright (c) 2022 Henrik Grimler
+ */
+
+/dts-v1/;
+#include "exynos5420-galaxy-tab-common.dtsi"
+
+/ {
+	model = "Samsung Chagall WiFi based on Exynos5420";
+	compatible = "samsung,chagall-wifi", "samsung,exynos5420", \
+		     "samsung,exynos5";
+};
+
+&ldo15_reg {
+	/* Unused */
+	regulator-name = "VDD_LDO15";
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+};
+
+&ldo17_reg {
+	regulator-name = "VDD_IRLED_3V3";
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3350000>;
+	regulator-always-on;
+	regulator-boot-on;
+
+	regulator-state-mem {
+		regulator-off-in-suspend;
+	};
+};
+
+&ldo28_reg {
+	/* Unused */
+	regulator-name = "VDD_LDO28";
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+};
+
+&ldo29_reg {
+	regulator-name = "VDD_TCON_1V8";
+	regulator-min-microvolt = <1900000>;
+	regulator-max-microvolt = <1900000>;
+
+	regulator-state-mem {
+		regulator-off-in-suspend;
+	};
+};
+
+&ldo31_reg {
+	regulator-name = "VDD_GRIP_1V8";
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+	regulator-always-on;
+	regulator-boot-on;
+
+	regulator-state-mem {
+		regulator-off-in-suspend;
+	};
+};
+
+&ldo32_reg {
+	regulator-name = "VDD_TSP_1V8";
+	regulator-min-microvolt = <1900000>;
+	regulator-max-microvolt = <1900000>;
+
+	regulator-state-mem {
+		regulator-off-in-suspend;
+	};
+};
diff --git a/arch/arm/boot/dts/exynos5420-galaxy-tab-common.dtsi b/arch/arm/boot/dts/exynos5420-galaxy-tab-common.dtsi
new file mode 100644
index 000000000000..d19bc3d266fa
--- /dev/null
+++ b/arch/arm/boot/dts/exynos5420-galaxy-tab-common.dtsi
@@ -0,0 +1,691 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Base DT for Samsung's family of tablets based on Exynos5420.
+ *
+ * Copyright (c) 2012-2013 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
+ * Copyright (c) 2022 Henrik Grimler
+ */
+
+/dts-v1/;
+#include "exynos5420.dtsi"
+#include "exynos5420-cpus.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/clock/samsung,s2mps11.h>
+
+/ {
+	chassis-type = "tablet";
+
+	/*
+	 * To successfully boot the mainline kernel with the stock
+	 * bootloader (SBOOT), the tlb needs to be flushed after the
+	 * page table pointer has been updated in __common_mmu_cache_on.
+	 * The same hack is also needed to boot exynos4412-i9300 with
+	 * stock bootloader, and probably other Samsung devices of
+	 * similar age.  See
+	 * https://lore.kernel.org/all/1355276466-18295-1-git-send-email-arve@android.com
+	 * for more details.
+	 */
+
+	chosen {
+		stdout-path = "serial2:115200n8";
+	};
+
+	memory@20000000 {
+		device_type = "memory";
+		reg = <0x20000000 0xc0000000>;
+	};
+
+	firmware@2073000 {
+		compatible = "samsung,secure-firmware";
+		reg = <0x02073000 0x1000>;
+	};
+
+	fixed-rate-clocks {
+		oscclk {
+			compatible = "samsung,exynos5420-oscclk";
+			clock-frequency = <24000000>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+
+		key-power {
+			debounce-interval = <10>;
+			gpios = <&gpx2 2 GPIO_ACTIVE_LOW>;
+			label = "Power";
+			linux,code = <KEY_POWER>;
+			wakeup-source;
+		};
+
+		key-home {
+			debounce-interval = <10>;
+			gpios = <&gpx0 5 GPIO_ACTIVE_LOW>;
+			label = "Home";
+			linux,code = <KEY_HOME>;
+			wakeup-source;
+		};
+
+		key-volume-up {
+			debounce-interval = <10>;
+			gpios = <&gpx0 2 GPIO_ACTIVE_LOW>;
+			label = "Volume Up";
+			linux,code = <KEY_VOLUMEUP>;
+		};
+
+		key-volume-down {
+			debounce-interval = <10>;
+			gpios = <&gpx0 3 GPIO_ACTIVE_LOW>;
+			label = "Volume Down";
+			linux,code = <KEY_VOLUMEDOWN>;
+		};
+	};
+};
+
+&cci {
+	/* CCI is disabled in hardware */
+	status = "disabled";
+};
+
+&cpu0 {
+	cpu-supply = <&buck2_reg>;
+};
+
+&cpu4 {
+	cpu-supply = <&buck6_reg>;
+};
+
+&gpu {
+	status = "okay";
+	mali-supply = <&buck4_reg>;
+};
+
+&hsi2c_7 {
+	status = "okay";
+
+	pmic@66 {
+		compatible = "samsung,s2mps11-pmic";
+		reg = <0x66>;
+
+		interrupt-parent = <&gpx3>;
+		interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&s2mps11_irq>;
+
+		s2mps11_osc: clocks {
+			compatible = "samsung,s2mps11-clk";
+			#clock-cells = <1>;
+			clock-output-names = "s2mps11_ap", "s2mps11_cp",
+					     "s2mps11_bt";
+		};
+
+		regulators {
+			buck1_reg: BUCK1 {
+				regulator-name = "VDD_MIF_1V1";
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <1300000>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			buck2_reg: BUCK2 {
+				regulator-name = "VDD_ARM_1V0";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1500000>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			buck3_reg: BUCK3 {
+				regulator-name = "VDD_INT_1V0";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1400000>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			buck4_reg: BUCK4 {
+				regulator-name = "VDD_G3D_1V0";
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <1400000>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			buck5_reg: BUCK5 {
+				regulator-name = "VDD_MEM_1V2";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+
+			};
+
+			buck6_reg: BUCK6 {
+				regulator-name = "VDD_KFC_1V0";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1500000>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			buck7_reg: BUCK7 {
+				regulator-name = "VIN_LLDO_1V4";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1500000>;
+				regulator-always-on;
+			};
+
+			buck8_reg: BUCK8 {
+				regulator-name = "VIN_MLDO_2V0";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <2100000>;
+				regulator-always-on;
+			};
+
+			buck9_reg: BUCK9 {
+				regulator-name = "VIN_HLDO_3V5";
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3500000>;
+				regulator-always-on;
+			};
+
+			buck10_reg: BUCK10 {
+				regulator-name = "VDD_CAM_ISP_1V0";
+				regulator-min-microvolt = <750000>;
+				regulator-max-microvolt = <3550000>;
+			};
+
+			ldo1_reg: LDO1 {
+				regulator-name = "VDD_ALIVE_1.0V";
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-always-on;
+			};
+
+			ldo2_reg: LDO2 {
+				regulator-name = "VDD_APIO_1V8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			ldo3_reg: LDO3 {
+				regulator-name = "VDD_APIO_MMC01_1V8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			ldo4_reg: LDO4 {
+				regulator-name = "VDD_ADC_1V8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			ldo5_reg: LDO5 {
+				/* Unused */
+				regulator-name = "VDD_LDO5";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+
+			ldo6_reg: LDO6 {
+				regulator-name = "VDD_MIPI_1V0";
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			ldo7_reg: LDO7 {
+				regulator-name = "VDD_MIPI_PLL_ABB1_18V";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			ldo8_reg: LDO8 {
+				/* Unused */
+				regulator-name = "VDD_LDO8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+
+			ldo9_reg: LDO9 {
+				regulator-name = "VDD_UOTG_3V0";
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			ldo10_reg: LDO10 {
+				regulator-name = "VDDQ_PRE_1V8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			ldo11_reg: LDO11 {
+				regulator-name = "VDD_HSIC_1V0";
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			ldo12_reg: LDO12 {
+				regulator-name = "VDD_HSIC_1V8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			ldo13_reg: LDO13 {
+				regulator-name = "VDD_APIO_MMC2_2V8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <2800000>;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			ldo14_reg: LDO14 {
+				regulator-name = "VDD_MOTOR_3V0";
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3000000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			ldo15_reg: LDO15 {
+				regulator-name = "VDD_LDO15";
+				/*
+				 * LDO15 varies between devices and is
+				 * specified in the device dts
+				 */
+			};
+
+			ldo16_reg: LDO16 {
+				regulator-name = "VDD_AP_2V8";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			ldo17_reg: LDO17 {
+				regulator-name = "VDD_LDO17";
+				/*
+				 * LDO17 varies between devices and is
+				 * specified in the device dts
+				 */
+			};
+
+			ldo18_reg: LDO18 {
+				/* Unused */
+				regulator-name = "VDD_LDO18";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+
+			ldo19_reg: LDO19 {
+				regulator-name = "VDD_VTF_2V8";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			ldo20_reg: LDO20 {
+				regulator-name = "VDD_CAM1_CAM_1V8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			ldo21_reg: LDO21 {
+				regulator-name = "VDD_CAM_IO_1V8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			ldo22_reg: LDO22 {
+				regulator-name = "VDD_CAM0_S_CORE_1V1";
+				regulator-min-microvolt = <1050000>;
+				regulator-max-microvolt = <1200000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			ldo23_reg: LDO23 {
+				regulator-name = "VDD_MIFS_1V1";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-always-on;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			ldo24_reg: LDO24 {
+				regulator-name = "VDD_TSP_3V3";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			ldo25_reg: LDO25 {
+				/* Unused */
+				regulator-name = "VDD_LDO25";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <3950000>;
+			};
+
+			ldo26_reg: LDO26 {
+				regulator-name = "VDD_CAM0_AF_2V8";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			ldo27_reg: LDO27 {
+				regulator-name = "VDD_G3DS_1V0";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-always-on;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			ldo28_reg: LDO28 {
+				regulator-name = "VDD_LDO28";
+				/*
+				 * LDO28 varies between devices and is
+				 * specified in the device dts
+				 */
+			};
+
+			ldo29_reg: LDO29 {
+				regulator-name = "VDD_LDO29";
+				/*
+				 * LDO29 varies between devices and is
+				 * specified in the device dts
+				 */
+			};
+
+			ldo30_reg: LDO30 {
+				regulator-name = "VDD_TOUCH_1V8";
+				regulator-min-microvolt = <1900000>;
+				regulator-max-microvolt = <1900000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			ldo31_reg: LDO31 {
+				regulator-name = "VDD_LDO31";
+				/*
+				 * LDO31 varies between devices and is
+				 * specified in the device dts
+				 */
+			};
+
+			ldo32_reg: LDO32 {
+				regulator-name = "VDD_LDO32";
+				/*
+				 * LDO32 varies between devices and is
+				 * specified in the device dts
+				 */
+			};
+
+			ldo33_reg: LDO33 {
+				regulator-name = "VDD_MHL_1V8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			ldo34_reg: LDO34 {
+				regulator-name = "VDD_MHL_3V3";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			ldo35_reg: LDO35 {
+				regulator-name = "VDD_SIL_1V2";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			ldo36_reg: LDO36 {
+				/* Unused */
+				regulator-name = "VDD_LDO36";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <3950000>;
+			};
+
+			ldo37_reg: LDO37 {
+				/* Unused */
+				regulator-name = "VDD_LDO37";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <3950000>;
+			};
+
+			ldo38_reg: LDO38 {
+				regulator-name = "VDD_KEY_LED_3V3";
+				regulator-min-microvolt = <2500000>;
+				regulator-max-microvolt = <3300000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+		};
+	};
+};
+
+&mixer {
+	status = "okay";
+};
+
+/* Internal storage */
+&mmc_0 {
+	status = "okay";
+	bus-width = <8>;
+	cap-mmc-highspeed;
+	card-detect-delay = <200>;
+	mmc-hs200-1_8v;
+	non-removable;
+	pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus1 &sd0_bus4 &sd0_bus8>;
+	pinctrl-names = "default";
+	samsung,dw-mshc-ciu-div = <3>;
+	samsung,dw-mshc-ddr-timing = <0 2>;
+	samsung,dw-mshc-sdr-timing = <0 4>;
+	vqmmc-supply = <&ldo3_reg>;
+};
+
+/* External sdcard */
+&mmc_2 {
+	status = "okay";
+	bus-width = <4>;
+	cap-sd-highspeed;
+	card-detect-delay = <200>;
+	cd-gpios = <&gpx2 4 GPIO_ACTIVE_LOW>;
+	pinctrl-0 = <&sd2_clk &sd2_cmd &mmc2_cd &sd2_bus1 &sd2_bus4>;
+	pinctrl-names = "default";
+	samsung,dw-mshc-ciu-div = <3>;
+	samsung,dw-mshc-ddr-timing = <0 2>;
+	samsung,dw-mshc-sdr-timing = <0 4>;
+	sd-uhs-sdr50;
+	vmmc-supply = <&ldo19_reg>;
+	vqmmc-supply = <&ldo13_reg>;
+};
+
+&pinctrl_0 {
+	mmc2_cd: mmc2-cd-pins {
+		samsung,pins = "gpx2-4";
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	s2mps11_irq: s2mps11-irq-pins {
+		samsung,pins = "gpx3-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
+};
+
+&rtc {
+	status = "okay";
+	clocks = <&clock CLK_RTC>, <&s2mps11_osc S2MPS11_CLK_AP>;
+	clock-names = "rtc", "rtc_src";
+};
+
+&tmu_cpu0 {
+	vtmu-supply = <&ldo10_reg>;
+};
+
+&tmu_cpu1 {
+	vtmu-supply = <&ldo10_reg>;
+};
+
+&tmu_cpu2 {
+	vtmu-supply = <&ldo10_reg>;
+};
+
+&tmu_cpu3 {
+	vtmu-supply = <&ldo10_reg>;
+};
+
+&tmu_gpu {
+	vtmu-supply = <&ldo10_reg>;
+};
+
+&usbdrd_dwc3_0 {
+	dr_mode = "peripheral";
+};
+
+&usbdrd_dwc3_1 {
+	dr_mode = "peripheral";
+};
+
+&usbdrd3_0 {
+	vdd33-supply = <&ldo9_reg>;
+	vdd10-supply = <&ldo11_reg>;
+};
+
+&usbdrd3_1 {
+	vdd33-supply = <&ldo9_reg>;
+	vdd10-supply = <&ldo11_reg>;
+};
diff --git a/arch/arm/boot/dts/exynos5420-klimt-wifi.dts b/arch/arm/boot/dts/exynos5420-klimt-wifi.dts
new file mode 100644
index 000000000000..011787b1bbf0
--- /dev/null
+++ b/arch/arm/boot/dts/exynos5420-klimt-wifi.dts
@@ -0,0 +1,75 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Samsung's Exynos5420 Klimt WiFi board device tree source
+ *
+ * Copyright (c) 2012-2013 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
+ * Copyright (c) 2022 Henrik Grimler
+ */
+
+/dts-v1/;
+#include "exynos5420-galaxy-tab-common.dtsi"
+
+/ {
+	model = "Samsung Klimt WiFi based on Exynos5420";
+	compatible = "samsung,klimt-wifi", "samsung,exynos5420", \
+		     "samsung,exynos5";
+};
+
+&ldo15_reg {
+	/* Unused */
+	regulator-name = "VDD_LDO15";
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+};
+
+&ldo17_reg {
+	regulator-name = "VDD_VCI_3V0";
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+
+	regulator-state-mem {
+		regulator-off-in-suspend;
+	};
+};
+
+&ldo28_reg {
+	regulator-name = "VDD3_1V8";
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+
+	regulator-state-mem {
+		regulator-off-in-suspend;
+	};
+};
+
+&ldo29_reg {
+	regulator-name = "VDDR_1V6";
+	regulator-min-microvolt = <1600000>;
+	regulator-max-microvolt = <1600000>;
+
+	regulator-state-mem {
+		regulator-off-in-suspend;
+	};
+};
+
+&ldo31_reg {
+	/* Unused */
+	regulator-name = "VDD_LDO31";
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+};
+
+&ldo32_reg {
+	regulator-name = "VDD_TSP_1V8";
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <1800000>;
+
+	regulator-state-mem {
+		regulator-off-in-suspend;
+	};
+};
+
+&mmc_2 {
+	sd-uhs-sdr104;
+};
diff --git a/arch/arm/boot/dts/exynos5420-peach-pit.dts b/arch/arm/boot/dts/exynos5420-peach-pit.dts
index e76fb104db19..9e2123470cad 100644
--- a/arch/arm/boot/dts/exynos5420-peach-pit.dts
+++ b/arch/arm/boot/dts/exynos5420-peach-pit.dts
@@ -60,7 +60,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&power_key_irq &lid_irq>;
 
-		power {
+		power-key {
 			label = "Power";
 			gpios = <&gpx1 2 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
@@ -212,7 +212,7 @@
 		interrupts = <1 IRQ_TYPE_NONE>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&max77802_irq>, <&pmic_selb>,
-			    <&pmic_dvs_1>, <&pmic_dvs_2>, <&pmic_dvs_3>;
+			    <&pmic_dvs_1>, <&pmic_dvs_2>;
 		wakeup-source;
 		reg = <0x9>;
 		#clock-cells = <1>;
@@ -774,14 +774,14 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&mask_tpm_reset>;
 
-	wifi_en: wifi-en {
+	wifi_en: wifi-en-pins {
 		samsung,pins = "gpx0-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	max98090_irq: max98090-irq {
+	max98090_irq: max98090-irq-pins {
 		samsung,pins = "gpx0-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
@@ -789,7 +789,7 @@
 	};
 
 	/* We need GPX0_6 to be low at sleep time; just keep it low always */
-	mask_tpm_reset: mask-tpm-reset {
+	mask_tpm_reset: mask-tpm-reset-pins {
 		samsung,pins = "gpx0-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
@@ -797,70 +797,70 @@
 		samsung,pin-val = <0>;
 	};
 
-	tpm_irq: tpm-irq {
+	tpm_irq: tpm-irq-pins {
 		samsung,pins = "gpx1-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	trackpad_irq: trackpad-irq {
+	trackpad_irq: trackpad-irq-pins {
 		samsung,pins = "gpx1-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	power_key_irq: power-key-irq {
+	power_key_irq: power-key-irq-pins {
 		samsung,pins = "gpx1-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	ec_irq: ec-irq {
+	ec_irq: ec-irq-pins {
 		samsung,pins = "gpx1-5";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	tps65090_irq: tps65090-irq {
+	tps65090_irq: tps65090-irq-pins {
 		samsung,pins = "gpx2-5";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	dp_hpd_gpio: dp_hpd_gpio {
+	dp_hpd_gpio: dp-hpd-gpio-pins {
 		samsung,pins = "gpx2-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	max77802_irq: max77802-irq {
+	max77802_irq: max77802-irq-pins {
 		samsung,pins = "gpx3-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	lid_irq: lid-irq {
+	lid_irq: lid-irq-pins {
 		samsung,pins = "gpx3-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	hdmi_hpd_irq: hdmi-hpd-irq {
+	hdmi_hpd_irq: hdmi-hpd-irq-pins {
 		samsung,pins = "gpx3-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	pmic_dvs_1: pmic-dvs-1 {
+	pmic_dvs_1: pmic-dvs-1-pins {
 		samsung,pins = "gpy7-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
@@ -868,74 +868,67 @@
 	};
 };
 
-&pinctrl_1 {
-	/* Adjust WiFi drive strengths lower for EMI */
-	sd1_clk: sd1-clk {
-		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
-	};
+/* pinctrl_1 */
+/* Adjust WiFi drive strengths lower for EMI */
+&sd1_bus1 {
+	samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
+};
 
-	sd1_cmd: sd1-cmd {
-		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
-	};
+&sd1_bus4 {
+	samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
+};
 
-	sd1_bus1: sd1-bus-width1 {
-		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
-	};
+&sd1_bus8 {
+	samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
+};
 
-	sd1_bus4: sd1-bus-width4 {
-		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
-	};
+&sd1_clk {
+	samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
+};
 
-	sd1_bus8: sd1-bus-width8 {
-		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
-	};
+&sd1_cmd {
+	samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
 };
 
 &pinctrl_2 {
-	pmic_dvs_2: pmic-dvs-2 {
-		samsung,pins = "gpj4-2";
+	pmic_dvs_2: pmic-dvs-2-pins {
+		samsung,pins = "gpj4-2", "gpj4-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
+};
 
-	pmic_dvs_3: pmic-dvs-3 {
-		samsung,pins = "gpj4-3";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
-		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
-	};
+/* pinctrl_3*/
+/* Drive SPI lines at x2 for better integrity */
+&spi2_bus {
+	samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
 };
 
 &pinctrl_3 {
-	/* Drive SPI lines at x2 for better integrity */
-	spi2-bus {
-		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
-	};
-
 	/* Drive SPI chip select at x2 for better integrity */
-	ec_spi_cs: ec-spi-cs {
+	ec_spi_cs: ec-spi-cs-pins {
 		samsung,pins = "gpb1-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
 	};
 
-	usb300_vbus_en: usb300-vbus-en {
+	usb300_vbus_en: usb300-vbus-en-pins {
 		samsung,pins = "gph0-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	usb301_vbus_en: usb301-vbus-en {
+	usb301_vbus_en: usb301-vbus-en-pins {
 		samsung,pins = "gph0-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	pmic_selb: pmic-selb {
+	pmic_selb: pmic-selb-pins {
 		samsung,pins = "gph0-2", "gph0-3", "gph0-4", "gph0-5",
 			       "gph0-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
@@ -1090,6 +1083,16 @@
 	vtmu-supply = <&ldo10_reg>;
 };
 
+&usbdrd3_0 {
+	vdd10-supply = <&ldo15_reg>;
+	vdd33-supply = <&ldo12_reg>;
+};
+
+&usbdrd3_1 {
+	vdd10-supply = <&ldo15_reg>;
+	vdd33-supply = <&ldo12_reg>;
+};
+
 &usbdrd_dwc3_0 {
 	dr_mode = "host";
 };
diff --git a/arch/arm/boot/dts/exynos5420-pinctrl.dtsi b/arch/arm/boot/dts/exynos5420-pinctrl.dtsi
index b82af7c89654..14cf9c4ca0ed 100644
--- a/arch/arm/boot/dts/exynos5420-pinctrl.dtsi
+++ b/arch/arm/boot/dts/exynos5420-pinctrl.dtsi
@@ -9,10 +9,10 @@
  * tree nodes are listed in this file.
  */
 
-#include <dt-bindings/pinctrl/samsung.h>
+#include "exynos-pinctrl.h"
 
 &pinctrl_0 {
-	gpy7: gpy7 {
+	gpy7: gpy7-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -20,7 +20,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpx0: gpx0 {
+	gpx0: gpx0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -31,7 +31,7 @@
 			     <26 0>, <26 1>, <27 0>, <27 1>;
 	};
 
-	gpx1: gpx1 {
+	gpx1: gpx1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -42,7 +42,7 @@
 			     <30 0>, <30 1>, <31 0>, <31 1>;
 	};
 
-	gpx2: gpx2 {
+	gpx2: gpx2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -50,7 +50,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpx3: gpx3 {
+	gpx3: gpx3-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -58,14 +58,14 @@
 		#interrupt-cells = <2>;
 	};
 
-	dp_hpd: dp_hpd {
+	dp_hpd: dp-hpd-pins {
 		samsung,pins = "gpx0-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	hdmi_cec: hdmi-cec {
+	hdmi_cec: hdmi-cec-pins {
 		samsung,pins = "gpx3-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
@@ -74,7 +74,7 @@
 };
 
 &pinctrl_1 {
-	gpc0: gpc0 {
+	gpc0: gpc0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -82,7 +82,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpc1: gpc1 {
+	gpc1: gpc1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -90,7 +90,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpc2: gpc2 {
+	gpc2: gpc2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -98,7 +98,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpc3: gpc3 {
+	gpc3: gpc3-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -106,7 +106,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpc4: gpc4 {
+	gpc4: gpc4-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -114,7 +114,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpd1: gpd1 {
+	gpd1: gpd1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -122,175 +122,175 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpy0: gpy0 {
+	gpy0: gpy0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpy1: gpy1 {
+	gpy1: gpy1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpy2: gpy2 {
+	gpy2: gpy2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpy3: gpy3 {
+	gpy3: gpy3-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpy4: gpy4 {
+	gpy4: gpy4-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpy5: gpy5 {
+	gpy5: gpy5-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpy6: gpy6 {
+	gpy6: gpy6-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	sd0_clk: sd0-clk {
+	sd0_clk: sd0-clk-pins {
 		samsung,pins = "gpc0-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
 	};
 
-	sd0_cmd: sd0-cmd {
+	sd0_cmd: sd0-cmd-pins {
 		samsung,pins = "gpc0-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
 	};
 
-	sd0_cd: sd0-cd {
+	sd0_cd: sd0-cd-pins {
 		samsung,pins = "gpc0-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
 	};
 
-	sd0_bus1: sd0-bus-width1 {
+	sd0_bus1: sd0-bus-width1-pins {
 		samsung,pins = "gpc0-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
 	};
 
-	sd0_bus4: sd0-bus-width4 {
+	sd0_bus4: sd0-bus-width4-pins {
 		samsung,pins = "gpc0-4", "gpc0-5", "gpc0-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
 	};
 
-	sd0_bus8: sd0-bus-width8 {
+	sd0_bus8: sd0-bus-width8-pins {
 		samsung,pins = "gpc3-0", "gpc3-1", "gpc3-2", "gpc3-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
 	};
 
-	sd0_rclk: sd0-rclk {
+	sd0_rclk: sd0-rclk-pins {
 		samsung,pins = "gpc0-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
 	};
 
-	sd1_clk: sd1-clk {
+	sd1_clk: sd1-clk-pins {
 		samsung,pins = "gpc1-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
 	};
 
-	sd1_cmd: sd1-cmd {
+	sd1_cmd: sd1-cmd-pins {
 		samsung,pins = "gpc1-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
 	};
 
-	sd1_cd: sd1-cd {
+	sd1_cd: sd1-cd-pins {
 		samsung,pins = "gpc1-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
 	};
 
-	sd1_int: sd1-int {
+	sd1_int: sd1-int-pins {
 		samsung,pins = "gpd1-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	sd1_bus1: sd1-bus-width1 {
+	sd1_bus1: sd1-bus-width1-pins {
 		samsung,pins = "gpc1-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
 	};
 
-	sd1_bus4: sd1-bus-width4 {
+	sd1_bus4: sd1-bus-width4-pins {
 		samsung,pins = "gpc1-4", "gpc1-5", "gpc1-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
 	};
 
-	sd1_bus8: sd1-bus-width8 {
+	sd1_bus8: sd1-bus-width8-pins {
 		samsung,pins = "gpd1-4", "gpd1-5", "gpd1-6", "gpd1-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
 	};
 
-	sd2_clk: sd2-clk {
+	sd2_clk: sd2-clk-pins {
 		samsung,pins = "gpc2-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
 	};
 
-	sd2_cmd: sd2-cmd {
+	sd2_cmd: sd2-cmd-pins {
 		samsung,pins = "gpc2-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
 	};
 
-	sd2_cd: sd2-cd {
+	sd2_cd: sd2-cd-pins {
 		samsung,pins = "gpc2-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
 	};
 
-	sd2_bus1: sd2-bus-width1 {
+	sd2_bus1: sd2-bus-width1-pins {
 		samsung,pins = "gpc2-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
 	};
 
-	sd2_bus4: sd2-bus-width4 {
+	sd2_bus4: sd2-bus-width4-pins {
 		samsung,pins = "gpc2-4", "gpc2-5", "gpc2-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
 	};
 
-	sd2_wp: sd2-wp {
+	sd2_wp: sd2-wp-pins {
 		samsung,pins = "gpc4-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
@@ -299,7 +299,7 @@
 };
 
 &pinctrl_2 {
-	gpe0: gpe0 {
+	gpe0: gpe0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -307,7 +307,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpe1: gpe1 {
+	gpe1: gpe1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -315,7 +315,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpf0: gpf0 {
+	gpf0: gpf0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -323,7 +323,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpf1: gpf1 {
+	gpf1: gpf1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -331,7 +331,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpg0: gpg0 {
+	gpg0: gpg0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -339,7 +339,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpg1: gpg1 {
+	gpg1: gpg1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -347,7 +347,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpg2: gpg2 {
+	gpg2: gpg2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -355,7 +355,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpj4: gpj4 {
+	gpj4: gpj4-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -363,7 +363,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	cam_gpio_a: cam-gpio-a {
+	cam_gpio_a: cam-gpio-a-pins {
 		samsung,pins = "gpe0-0", "gpe0-1", "gpe0-2", "gpe0-3",
 			       "gpe0-4", "gpe0-5", "gpe0-6", "gpe0-7",
 			       "gpe1-0", "gpe1-1";
@@ -372,7 +372,7 @@
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	cam_gpio_b: cam-gpio-b {
+	cam_gpio_b: cam-gpio-b-pins {
 		samsung,pins = "gpf0-0", "gpf0-1", "gpf0-2", "gpf0-3",
 			       "gpf1-0", "gpf1-1", "gpf1-2", "gpf1-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
@@ -380,42 +380,42 @@
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	cam_i2c2_bus: cam-i2c2-bus {
+	cam_i2c2_bus: cam-i2c2-bus-pins {
 		samsung,pins = "gpf0-4", "gpf0-5";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	cam_spi1_bus: cam-spi1-bus {
+	cam_spi1_bus: cam-spi1-bus-pins {
 		samsung,pins = "gpe0-4", "gpe0-5", "gpf0-2", "gpf0-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	cam_i2c1_bus: cam-i2c1-bus {
+	cam_i2c1_bus: cam-i2c1-bus-pins {
 		samsung,pins = "gpf0-2", "gpf0-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	cam_i2c0_bus: cam-i2c0-bus {
+	cam_i2c0_bus: cam-i2c0-bus-pins {
 		samsung,pins = "gpf0-0", "gpf0-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	cam_spi0_bus: cam-spi0-bus {
+	cam_spi0_bus: cam-spi0-bus-pins {
 		samsung,pins = "gpf1-0", "gpf1-1", "gpf1-2", "gpf1-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	cam_bayrgb_bus: cam-bayrgb-bus {
+	cam_bayrgb_bus: cam-bayrgb-bus-pins {
 		samsung,pins = "gpg0-0", "gpg0-1", "gpg0-2", "gpg0-3",
 			       "gpg0-4", "gpg0-5", "gpg0-6", "gpg0-7",
 			       "gpg1-0", "gpg1-1", "gpg1-2", "gpg1-3",
@@ -428,7 +428,7 @@
 };
 
 &pinctrl_3 {
-	gpa0: gpa0 {
+	gpa0: gpa0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -436,7 +436,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpa1: gpa1 {
+	gpa1: gpa1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -444,7 +444,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpa2: gpa2 {
+	gpa2: gpa2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -452,7 +452,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpb0: gpb0 {
+	gpb0: gpb0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -460,7 +460,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpb1: gpb1 {
+	gpb1: gpb1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -468,7 +468,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpb2: gpb2 {
+	gpb2: gpb2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -476,7 +476,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpb3: gpb3 {
+	gpb3: gpb3-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -484,7 +484,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpb4: gpb4 {
+	gpb4: gpb4-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -492,7 +492,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gph0: gph0 {
+	gph0: gph0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -500,98 +500,98 @@
 		#interrupt-cells = <2>;
 	};
 
-	uart0_data: uart0-data {
+	uart0_data: uart0-data-pins {
 		samsung,pins = "gpa0-0", "gpa0-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	uart0_fctl: uart0-fctl {
+	uart0_fctl: uart0-fctl-pins {
 		samsung,pins = "gpa0-2", "gpa0-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	uart1_data: uart1-data {
+	uart1_data: uart1-data-pins {
 		samsung,pins = "gpa0-4", "gpa0-5";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	uart1_fctl: uart1-fctl {
+	uart1_fctl: uart1-fctl-pins {
 		samsung,pins = "gpa0-6", "gpa0-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	i2c2_bus: i2c2-bus {
+	i2c2_bus: i2c2-bus-pins {
 		samsung,pins = "gpa0-6", "gpa0-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	uart2_data: uart2-data {
+	uart2_data: uart2-data-pins {
 		samsung,pins = "gpa1-0", "gpa1-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	uart2_fctl: uart2-fctl {
+	uart2_fctl: uart2-fctl-pins {
 		samsung,pins = "gpa1-2", "gpa1-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	i2c3_bus: i2c3-bus {
+	i2c3_bus: i2c3-bus-pins {
 		samsung,pins = "gpa1-2", "gpa1-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	uart3_data: uart3-data {
+	uart3_data: uart3-data-pins {
 		samsung,pins = "gpa1-4", "gpa1-5";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	spi0_bus: spi0-bus {
+	spi0_bus: spi0-bus-pins {
 		samsung,pins = "gpa2-0", "gpa2-1", "gpa2-2", "gpa2-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	spi1_bus: spi1-bus {
+	spi1_bus: spi1-bus-pins {
 		samsung,pins = "gpa2-4", "gpa2-6", "gpa2-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	i2c4_hs_bus: i2c4-hs-bus {
+	i2c4_hs_bus: i2c4-hs-bus-pins {
 		samsung,pins = "gpa2-0", "gpa2-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	i2c5_hs_bus: i2c5-hs-bus {
+	i2c5_hs_bus: i2c5-hs-bus-pins {
 		samsung,pins = "gpa2-2", "gpa2-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	i2s1_bus: i2s1-bus {
+	i2s1_bus: i2s1-bus-pins {
 		samsung,pins = "gpb0-0", "gpb0-1", "gpb0-2", "gpb0-3",
 			       "gpb0-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
@@ -599,7 +599,7 @@
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	pcm1_bus: pcm1-bus {
+	pcm1_bus: pcm1-bus-pins {
 		samsung,pins = "gpb0-0", "gpb0-1", "gpb0-2", "gpb0-3",
 			       "gpb0-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
@@ -607,7 +607,7 @@
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	i2s2_bus: i2s2-bus {
+	i2s2_bus: i2s2-bus-pins {
 		samsung,pins = "gpb1-0", "gpb1-1", "gpb1-2", "gpb1-3",
 			       "gpb1-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
@@ -615,7 +615,7 @@
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	pcm2_bus: pcm2-bus {
+	pcm2_bus: pcm2-bus-pins {
 		samsung,pins = "gpb1-0", "gpb1-1", "gpb1-2", "gpb1-3",
 			       "gpb1-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
@@ -623,91 +623,91 @@
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	spdif_bus: spdif-bus {
+	spdif_bus: spdif-bus-pins {
 		samsung,pins = "gpb1-0", "gpb1-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	spi2_bus: spi2-bus {
+	spi2_bus: spi2-bus-pins {
 		samsung,pins = "gpb1-1", "gpb1-3", "gpb1-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_5>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	i2c6_hs_bus: i2c6-hs-bus {
+	i2c6_hs_bus: i2c6-hs-bus-pins {
 		samsung,pins = "gpb1-3", "gpb1-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	pwm0_out: pwm0-out {
+	pwm0_out: pwm0-out-pins {
 		samsung,pins = "gpb2-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	pwm1_out: pwm1-out {
+	pwm1_out: pwm1-out-pins {
 		samsung,pins = "gpb2-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	pwm2_out: pwm2-out {
+	pwm2_out: pwm2-out-pins {
 		samsung,pins = "gpb2-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	pwm3_out: pwm3-out {
+	pwm3_out: pwm3-out-pins {
 		samsung,pins = "gpb2-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	i2c7_hs_bus: i2c7-hs-bus {
+	i2c7_hs_bus: i2c7-hs-bus-pins {
 		samsung,pins = "gpb2-2", "gpb2-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	i2c0_bus: i2c0-bus {
+	i2c0_bus: i2c0-bus-pins {
 		samsung,pins = "gpb3-0", "gpb3-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	i2c1_bus: i2c1-bus {
+	i2c1_bus: i2c1-bus-pins {
 		samsung,pins = "gpb3-2", "gpb3-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	i2c8_hs_bus: i2c8-hs-bus {
+	i2c8_hs_bus: i2c8-hs-bus-pins {
 		samsung,pins = "gpb3-4", "gpb3-5";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	i2c9_hs_bus: i2c9-hs-bus {
+	i2c9_hs_bus: i2c9-hs-bus-pins {
 		samsung,pins = "gpb3-6", "gpb3-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	i2c10_hs_bus: i2c10-hs-bus {
+	i2c10_hs_bus: i2c10-hs-bus-pins {
 		samsung,pins = "gpb4-0", "gpb4-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
@@ -716,7 +716,7 @@
 };
 
 &pinctrl_4 {
-	gpz: gpz {
+	gpz: gpz-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -724,7 +724,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	i2s0_bus: i2s0-bus {
+	i2s0_bus: i2s0-bus-pins {
 		samsung,pins = "gpz-0", "gpz-1", "gpz-2", "gpz-3",
 				"gpz-4", "gpz-5", "gpz-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
diff --git a/arch/arm/boot/dts/exynos5420-smdk5420.dts b/arch/arm/boot/dts/exynos5420-smdk5420.dts
index a4f0e3ffedbd..4d7b6d9008a7 100644
--- a/arch/arm/boot/dts/exynos5420-smdk5420.dts
+++ b/arch/arm/boot/dts/exynos5420-smdk5420.dts
@@ -124,6 +124,9 @@
 	hpd-gpios = <&gpx3 7 GPIO_ACTIVE_HIGH>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&hdmi_hpd_irq>;
+	vdd-supply = <&ldo6_reg>;
+	vdd_osc-supply = <&ldo7_reg>;
+	vdd_pll-supply = <&ldo6_reg>;
 };
 
 &hsi2c_4 {
@@ -377,7 +380,7 @@
 };
 
 &pinctrl_0 {
-	hdmi_hpd_irq: hdmi-hpd-irq {
+	hdmi_hpd_irq: hdmi-hpd-irq-pins {
 		samsung,pins = "gpx3-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
@@ -386,14 +389,14 @@
 };
 
 &pinctrl_2 {
-	usb300_vbus_en: usb300-vbus-en {
+	usb300_vbus_en: usb300-vbus-en-pins {
 		samsung,pins = "gpg0-5";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	usb301_vbus_en: usb301-vbus-en {
+	usb301_vbus_en: usb301-vbus-en-pins {
 		samsung,pins = "gpg1-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
@@ -407,6 +410,16 @@
 	clock-names = "rtc", "rtc_src";
 };
 
+&usbdrd3_0 {
+	vdd10-supply = <&ldo11_reg>;
+	vdd33-supply = <&ldo9_reg>;
+};
+
+&usbdrd3_1 {
+	vdd10-supply = <&ldo11_reg>;
+	vdd33-supply = <&ldo9_reg>;
+};
+
 &usbdrd_phy0 {
 	vbus-supply = <&usb300_vbus_reg>;
 };
diff --git a/arch/arm/boot/dts/exynos5420.dtsi b/arch/arm/boot/dts/exynos5420.dtsi
index e23e8ffb093f..9f2523a873d9 100644
--- a/arch/arm/boot/dts/exynos5420.dtsi
+++ b/arch/arm/boot/dts/exynos5420.dtsi
@@ -302,8 +302,8 @@
 			clocks = <&clock CLK_PCLK_PPMU_DREX0_0>;
 			clock-names = "ppmu";
 			events {
-				ppmu_event3_dmc0_0: ppmu-event3-dmc0_0 {
-					event-name = "ppmu-event3-dmc0_0";
+				ppmu_event3_dmc0_0: ppmu-event3-dmc0-0 {
+					event-name = "ppmu-event3-dmc0-0";
 				};
 			};
 		};
@@ -314,8 +314,8 @@
 			clocks = <&clock CLK_PCLK_PPMU_DREX0_1>;
 			clock-names = "ppmu";
 			events {
-				ppmu_event3_dmc0_1: ppmu-event3-dmc0_1 {
-					event-name = "ppmu-event3-dmc0_1";
+				ppmu_event3_dmc0_1: ppmu-event3-dmc0-1 {
+					event-name = "ppmu-event3-dmc0-1";
 				};
 			};
 		};
@@ -326,8 +326,8 @@
 			clocks = <&clock CLK_PCLK_PPMU_DREX1_0>;
 			clock-names = "ppmu";
 			events {
-				ppmu_event3_dmc1_0: ppmu-event3-dmc1_0 {
-					event-name = "ppmu-event3-dmc1_0";
+				ppmu_event3_dmc1_0: ppmu-event3-dmc1-0 {
+					event-name = "ppmu-event3-dmc1-0";
 				};
 			};
 		};
@@ -338,8 +338,8 @@
 			clocks = <&clock CLK_PCLK_PPMU_DREX1_1>;
 			clock-names = "ppmu";
 			events {
-				ppmu_event3_dmc1_1: ppmu-event3-dmc1_1 {
-					event-name = "ppmu-event3-dmc1_1";
+				ppmu_event3_dmc1_1: ppmu-event3-dmc1-1 {
+					event-name = "ppmu-event3-dmc1-1";
 				};
 			};
 		};
@@ -430,60 +430,50 @@
 			power-domains = <&mau_pd>;
 		};
 
-		adma: adma@3880000 {
+		adma: dma-controller@3880000 {
 			compatible = "arm,pl330", "arm,primecell";
 			reg = <0x03880000 0x1000>;
 			interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&clock_audss EXYNOS_ADMA>;
 			clock-names = "apb_pclk";
 			#dma-cells = <1>;
-			#dma-channels = <6>;
-			#dma-requests = <16>;
 			power-domains = <&mau_pd>;
 		};
 
-		pdma0: pdma@121a0000 {
+		pdma0: dma-controller@121a0000 {
 			compatible = "arm,pl330", "arm,primecell";
 			reg = <0x121A0000 0x1000>;
 			interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&clock CLK_PDMA0>;
 			clock-names = "apb_pclk";
 			#dma-cells = <1>;
-			#dma-channels = <8>;
-			#dma-requests = <32>;
 		};
 
-		pdma1: pdma@121b0000 {
+		pdma1: dma-controller@121b0000 {
 			compatible = "arm,pl330", "arm,primecell";
 			reg = <0x121B0000 0x1000>;
 			interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&clock CLK_PDMA1>;
 			clock-names = "apb_pclk";
 			#dma-cells = <1>;
-			#dma-channels = <8>;
-			#dma-requests = <32>;
 		};
 
-		mdma0: mdma@10800000 {
+		mdma0: dma-controller@10800000 {
 			compatible = "arm,pl330", "arm,primecell";
 			reg = <0x10800000 0x1000>;
 			interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&clock CLK_MDMA0>;
 			clock-names = "apb_pclk";
 			#dma-cells = <1>;
-			#dma-channels = <8>;
-			#dma-requests = <1>;
 		};
 
-		mdma1: mdma@11c10000 {
+		mdma1: dma-controller@11c10000 {
 			compatible = "arm,pl330", "arm,primecell";
 			reg = <0x11C10000 0x1000>;
 			interrupts = <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&clock CLK_MDMA1>;
 			clock-names = "apb_pclk";
 			#dma-cells = <1>;
-			#dma-channels = <8>;
-			#dma-requests = <1>;
 			/*
 			 * MDMA1 can support both secure and non-secure
 			 * AXI transactions. When this is enabled in
diff --git a/arch/arm/boot/dts/exynos5422-odroid-core.dtsi b/arch/arm/boot/dts/exynos5422-odroid-core.dtsi
index e7958dbecfd2..35818c4cd852 100644
--- a/arch/arm/boot/dts/exynos5422-odroid-core.dtsi
+++ b/arch/arm/boot/dts/exynos5422-odroid-core.dtsi
@@ -333,8 +333,6 @@
 		compatible	= "samsung,K3QF2F20DB", "jedec,lpddr3";
 		density		= <16384>;
 		io-width	= <32>;
-		#address-cells	= <1>;
-		#size-cells	= <0>;
 
 		tRFC-min-tck		= <17>;
 		tRRD-min-tck		= <2>;
@@ -358,10 +356,9 @@
 		tCKESR-min-tck		= <2>;
 		tMRD-min-tck		= <5>;
 
-		timings_samsung_K3QF2F20DB_800mhz: lpddr3-timings@800000000 {
+		timings_samsung_K3QF2F20DB_800mhz: timings {
 			compatible	= "jedec,lpddr3-timings";
-			/* workaround: 'reg' shows max-freq */
-			reg		= <800000000>;
+			max-freq	= <800000000>;
 			min-freq	= <100000000>;
 			tRFC		= <65000>;
 			tRRD		= <6000>;
@@ -999,7 +996,7 @@
 };
 
 &pinctrl_0 {
-	s2mps11_irq: s2mps11-irq {
+	s2mps11_irq: s2mps11-irq-pins {
 		samsung,pins = "gpx0-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
diff --git a/arch/arm/boot/dts/exynos5422-odroidhc1.dts b/arch/arm/boot/dts/exynos5422-odroidhc1.dts
index d91f7fa2cf80..3de7019572a2 100644
--- a/arch/arm/boot/dts/exynos5422-odroidhc1.dts
+++ b/arch/arm/boot/dts/exynos5422-odroidhc1.dts
@@ -8,6 +8,7 @@
  */
 
 /dts-v1/;
+#include <dt-bindings/leds/common.h>
 #include "exynos5422-odroid-core.dtsi"
 
 / {
@@ -19,7 +20,8 @@
 		compatible = "pwm-leds";
 
 		led-1 {
-			label = "blue:heartbeat";
+			function = LED_FUNCTION_HEARTBEAT;
+			color = <LED_COLOR_ID_BLUE>;
 			pwms = <&pwm 2 2000000 0>;
 			pwm-names = "pwm2";
 			max-brightness = <255>;
diff --git a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi
index e35af40a55cb..a6961ff24030 100644
--- a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi
+++ b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi
@@ -480,14 +480,14 @@
 };
 
 &pinctrl_0 {
-	power_key: power-key {
+	power_key: power-key-pins {
 		samsung,pins = "gpx0-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	hdmi_hpd_irq: hdmi-hpd-irq {
+	hdmi_hpd_irq: hdmi-hpd-irq-pins {
 		samsung,pins = "gpx3-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
@@ -496,7 +496,7 @@
 };
 
 &pinctrl_1 {
-	emmc_nrst_pin: emmc-nrst {
+	emmc_nrst_pin: emmc-nrst-pins {
 		samsung,pins = "gpd1-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
diff --git a/arch/arm/boot/dts/exynos5422-odroidxu3-lite.dts b/arch/arm/boot/dts/exynos5422-odroidxu3-lite.dts
index 62c5928aa994..e3154a1cae23 100644
--- a/arch/arm/boot/dts/exynos5422-odroidxu3-lite.dts
+++ b/arch/arm/boot/dts/exynos5422-odroidxu3-lite.dts
@@ -113,13 +113,13 @@
 	#size-cells = <0>;
 
 	hub@1 {
-		compatible = "usb0424,9514";
+		compatible = "usb424,9514";
 		reg = <1>;
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		ethernet: usbether@1 {
-			compatible = "usb0424,ec00";
+		ethernet: ethernet@1 {
+			compatible = "usb424,ec00";
 			reg = <1>;
 			local-mac-address = [00 00 00 00 00 00]; /* Filled in by a bootloader */
 		};
diff --git a/arch/arm/boot/dts/exynos5422-odroidxu3.dts b/arch/arm/boot/dts/exynos5422-odroidxu3.dts
index cecaeb69e623..a378d4937ff7 100644
--- a/arch/arm/boot/dts/exynos5422-odroidxu3.dts
+++ b/arch/arm/boot/dts/exynos5422-odroidxu3.dts
@@ -80,13 +80,13 @@
 	#size-cells = <0>;
 
 	hub@1 {
-		compatible = "usb0424,9514";
+		compatible = "usb424,9514";
 		reg = <1>;
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		ethernet: usbether@1 {
-			compatible = "usb0424,ec00";
+		ethernet: ethernet@1 {
+			compatible = "usb424,ec00";
 			reg = <1>;
 			local-mac-address = [00 00 00 00 00 00]; /* Filled in by a bootloader */
 		};
diff --git a/arch/arm/boot/dts/exynos5422-odroidxu4.dts b/arch/arm/boot/dts/exynos5422-odroidxu4.dts
index 1c24f9b35973..f5fb617f46bd 100644
--- a/arch/arm/boot/dts/exynos5422-odroidxu4.dts
+++ b/arch/arm/boot/dts/exynos5422-odroidxu4.dts
@@ -9,6 +9,7 @@
  */
 
 /dts-v1/;
+#include <dt-bindings/leds/common.h>
 #include <dt-bindings/sound/samsung-i2s.h>
 #include "exynos5422-odroidxu3-common.dtsi"
 
@@ -21,7 +22,8 @@
 		compatible = "pwm-leds";
 
 		led-1 {
-			label = "blue:heartbeat";
+			function = LED_FUNCTION_HEARTBEAT;
+			color = <LED_COLOR_ID_BLUE>;
 			pwms = <&pwm 2 2000000 0>;
 			pwm-names = "pwm2";
 			max-brightness = <255>;
diff --git a/arch/arm/boot/dts/exynos54xx-odroidxu-leds.dtsi b/arch/arm/boot/dts/exynos54xx-odroidxu-leds.dtsi
index 982752e1df24..8c0e1716c0b3 100644
--- a/arch/arm/boot/dts/exynos54xx-odroidxu-leds.dtsi
+++ b/arch/arm/boot/dts/exynos54xx-odroidxu-leds.dtsi
@@ -9,6 +9,7 @@
  */
 
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
 
 / {
 	led-controller-1 {
@@ -16,6 +17,8 @@
 
 		led-1 {
 			label = "green:mmc0";
+			function = LED_FUNCTION_DISK_ACTIVITY;
+			color = <LED_COLOR_ID_GREEN>;
 			pwms = <&pwm 1 2000000 0>;
 			pwm-names = "pwm1";
 			/*
@@ -27,7 +30,8 @@
 		};
 
 		led-2 {
-			label = "blue:heartbeat";
+			function = LED_FUNCTION_HEARTBEAT;
+			color = <LED_COLOR_ID_BLUE>;
 			pwms = <&pwm 2 2000000 0>;
 			pwm-names = "pwm2";
 			max-brightness = <255>;
@@ -40,6 +44,8 @@
 
 		led-3 {
 			label = "red:microSD";
+			function = LED_FUNCTION_DISK_ACTIVITY;
+			color = <LED_COLOR_ID_RED>;
 			gpios = <&gpx2 3 GPIO_ACTIVE_HIGH>;
 			default-state = "off";
 			linux,default-trigger = "mmc1";
diff --git a/arch/arm/boot/dts/exynos54xx.dtsi b/arch/arm/boot/dts/exynos54xx.dtsi
index 2ddb7a5f12b3..3ec43761d8b9 100644
--- a/arch/arm/boot/dts/exynos54xx.dtsi
+++ b/arch/arm/boot/dts/exynos54xx.dtsi
@@ -74,7 +74,8 @@
 		};
 
 		mct: timer@101c0000 {
-			compatible = "samsung,exynos4210-mct";
+			compatible = "samsung,exynos5420-mct",
+				     "samsung,exynos4210-mct";
 			reg = <0x101c0000 0xb00>;
 			interrupts-extended = <&combiner 23 3>,
 					      <&combiner 23 4>,
diff --git a/arch/arm/boot/dts/exynos5800-peach-pi.dts b/arch/arm/boot/dts/exynos5800-peach-pi.dts
index 77013ee586f8..0ebcb66c6319 100644
--- a/arch/arm/boot/dts/exynos5800-peach-pi.dts
+++ b/arch/arm/boot/dts/exynos5800-peach-pi.dts
@@ -59,7 +59,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&power_key_irq &lid_irq>;
 
-		power {
+		power-key {
 			label = "Power";
 			gpios = <&gpx1 2 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
@@ -221,7 +221,7 @@
 		interrupts = <1 IRQ_TYPE_NONE>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&max77802_irq>, <&pmic_selb>,
-			    <&pmic_dvs_1>, <&pmic_dvs_2>, <&pmic_dvs_3>;
+			    <&pmic_dvs_1>, <&pmic_dvs_2>;
 		wakeup-source;
 		reg = <0x9>;
 		#clock-cells = <1>;
@@ -756,14 +756,14 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&mask_tpm_reset>;
 
-	wifi_en: wifi-en {
+	wifi_en: wifi-en-pins {
 		samsung,pins = "gpx0-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	max98091_irq: max98091-irq {
+	max98091_irq: max98091-irq-pins {
 		samsung,pins = "gpx0-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
@@ -771,7 +771,7 @@
 	};
 
 	/* We need GPX0_6 to be low at sleep time; just keep it low always */
-	mask_tpm_reset: mask-tpm-reset {
+	mask_tpm_reset: mask-tpm-reset-pins {
 		samsung,pins = "gpx0-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
@@ -779,70 +779,70 @@
 		samsung,pin-val = <0>;
 	};
 
-	tpm_irq: tpm-irq {
+	tpm_irq: tpm-irq-pins {
 		samsung,pins = "gpx1-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	trackpad_irq: trackpad-irq {
+	trackpad_irq: trackpad-irq-pins {
 		samsung,pins = "gpx1-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	power_key_irq: power-key-irq {
+	power_key_irq: power-key-irq-pins {
 		samsung,pins = "gpx1-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	ec_irq: ec-irq {
+	ec_irq: ec-irq-pins {
 		samsung,pins = "gpx1-5";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	tps65090_irq: tps65090-irq {
+	tps65090_irq: tps65090-irq-pins {
 		samsung,pins = "gpx2-5";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	dp_hpd_gpio: dp_hpd_gpio {
+	dp_hpd_gpio: dp-hpd-gpio-pins {
 		samsung,pins = "gpx2-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	max77802_irq: max77802-irq {
+	max77802_irq: max77802-irq-pins {
 		samsung,pins = "gpx3-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	lid_irq: lid-irq {
+	lid_irq: lid-irq-pins {
 		samsung,pins = "gpx3-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	hdmi_hpd_irq: hdmi-hpd-irq {
+	hdmi_hpd_irq: hdmi-hpd-irq-pins {
 		samsung,pins = "gpx3-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	pmic_dvs_1: pmic-dvs-1 {
+	pmic_dvs_1: pmic-dvs-1-pins {
 		samsung,pins = "gpy7-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
@@ -850,74 +850,67 @@
 	};
 };
 
-&pinctrl_1 {
-	/* Adjust WiFi drive strengths lower for EMI */
-	sd1_clk: sd1-clk {
-		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
-	};
+/* pinctrl_1 */
+/* Adjust WiFi drive strengths lower for EMI */
+&sd1_bus1 {
+	samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
+};
 
-	sd1_cmd: sd1-cmd {
-		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
-	};
+&sd1_bus4 {
+	samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
+};
 
-	sd1_bus1: sd1-bus-width1 {
-		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
-	};
+&sd1_bus8 {
+	samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
+};
 
-	sd1_bus4: sd1-bus-width4 {
-		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
-	};
+&sd1_clk {
+	samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
+};
 
-	sd1_bus8: sd1-bus-width8 {
-		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
-	};
+&sd1_cmd {
+	samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
 };
 
 &pinctrl_2 {
-	pmic_dvs_2: pmic-dvs-2 {
-		samsung,pins = "gpj4-2";
+	pmic_dvs_2: pmic-dvs-2-pins {
+		samsung,pins = "gpj4-2", "gpj4-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
+};
 
-	pmic_dvs_3: pmic-dvs-3 {
-		samsung,pins = "gpj4-3";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
-		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
-	};
+/* pinctrl_3*/
+/* Drive SPI lines at x2 for better integrity */
+&spi2_bus {
+	samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
 };
 
 &pinctrl_3 {
-	/* Drive SPI lines at x2 for better integrity */
-	spi2-bus {
-		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
-	};
-
 	/* Drive SPI chip select at x2 for better integrity */
-	ec_spi_cs: ec-spi-cs {
+	ec_spi_cs: ec-spi-cs-pins {
 		samsung,pins = "gpb1-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
 	};
 
-	usb300_vbus_en: usb300-vbus-en {
+	usb300_vbus_en: usb300-vbus-en-pins {
 		samsung,pins = "gph0-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	usb301_vbus_en: usb301-vbus-en {
+	usb301_vbus_en: usb301-vbus-en-pins {
 		samsung,pins = "gph0-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
-	pmic_selb: pmic-selb {
+	pmic_selb: pmic-selb-pins {
 		samsung,pins = "gph0-2", "gph0-3", "gph0-4", "gph0-5",
 			       "gph0-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
@@ -1072,6 +1065,16 @@
 	vtmu-supply = <&ldo10_reg>;
 };
 
+&usbdrd3_0 {
+	vdd10-supply = <&ldo15_reg>;
+	vdd33-supply = <&ldo12_reg>;
+};
+
+&usbdrd3_1 {
+	vdd10-supply = <&ldo15_reg>;
+	vdd33-supply = <&ldo12_reg>;
+};
+
 &usbdrd_dwc3_0 {
 	dr_mode = "host";
 };
diff --git a/arch/arm/boot/dts/gemini-nas4220b.dts b/arch/arm/boot/dts/gemini-nas4220b.dts
index 13112a8a5dd8..6544c730340f 100644
--- a/arch/arm/boot/dts/gemini-nas4220b.dts
+++ b/arch/arm/boot/dts/gemini-nas4220b.dts
@@ -84,7 +84,7 @@
 			partitions {
 				compatible = "redboot-fis";
 				/* Eraseblock at 0xfe0000 */
-				fis-index-block = <0x1fc>;
+				fis-index-block = <0x7f>;
 			};
 		};
 
diff --git a/arch/arm/boot/dts/gemini-ns2502.dts b/arch/arm/boot/dts/gemini-ns2502.dts
index 704abd212df5..e6eeb35e8819 100644
--- a/arch/arm/boot/dts/gemini-ns2502.dts
+++ b/arch/arm/boot/dts/gemini-ns2502.dts
@@ -39,10 +39,6 @@
 		phy0: ethernet-phy@1 {
 			reg = <1>;
 			device_type = "ethernet-phy";
-			/* We lack the knowledge of necessary GPIO to achieve
-			 * Gigabit
-			 */
-			max-speed = <100>;
 		};
 	};
 };
@@ -50,7 +46,7 @@
 &ethernet {
 	status = "okay";
 	ethernet-port@0 {
-		phy-mode = "rgmii";
+		phy-mode = "rgmii-id";
 		phy-handle = <&phy0>;
 	};
 };
@@ -65,30 +61,9 @@
 	pinctrl-1 = <&pflash_disabled_pins>;
 
 	partitions {
-		compatible = "fixed-partitions";
-		#address-cells = <1>;
-		#size-cells = <1>;
-
-		partition@0 {
-			label = "RedBoot";
-			reg = <0x00000000 0x00020000>;
-		};
-		partition@20000 {
-			label = "kernel";
-			reg = <0x00020000 0x00700000>;
-		};
-		partition@720000 {
-			label = "VCTL";
-			reg = <0x00720000 0x00020000>;
-		};
-		partition@740000 {
-			label = "CurConf";
-			reg = <0x00740000 0x000a0000>;
-		};
-		partition@7e0000 {
-			label = "FIS";
-			reg = <0x007e0000 0x00010000>;
-		};
+		compatible = "redboot-fis";
+		/* Eraseblock at 0x7e0000 */
+		fis-index-block = <0x3f>;
 	};
 };
 
diff --git a/arch/arm/boot/dts/gemini-ssi1328.dts b/arch/arm/boot/dts/gemini-ssi1328.dts
index 2b3e7db84fed..42e85f07cf76 100644
--- a/arch/arm/boot/dts/gemini-ssi1328.dts
+++ b/arch/arm/boot/dts/gemini-ssi1328.dts
@@ -40,10 +40,6 @@
 		phy0: ethernet-phy@1 {
 			reg = <1>;
 			device_type = "ethernet-phy";
-			/* We lack the knowledge of necessary GPIO to achieve
-			 * Gigabit
-			 */
-			max-speed = <100>;
 		};
 		/* WAN ICPlus IP101A */
 		phy1: ethernet-phy@2 {
diff --git a/arch/arm/boot/dts/hpe-bmc-dl360gen10.dts b/arch/arm/boot/dts/hpe-bmc-dl360gen10.dts
new file mode 100644
index 000000000000..3a7382ce40ef
--- /dev/null
+++ b/arch/arm/boot/dts/hpe-bmc-dl360gen10.dts
@@ -0,0 +1,26 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device Tree file for HPE DL360Gen10
+ */
+
+/include/ "hpe-gxp.dtsi"
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	compatible = "hpe,gxp-dl360gen10", "hpe,gxp";
+	model = "Hewlett Packard Enterprise ProLiant dl360 Gen10";
+
+	aliases {
+		serial0 = &uartc;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@40000000 {
+		device_type = "memory";
+		reg = <0x40000000 0x20000000>;
+	};
+};
diff --git a/arch/arm/boot/dts/hpe-gxp.dtsi b/arch/arm/boot/dts/hpe-gxp.dtsi
new file mode 100644
index 000000000000..cf735b3c4f35
--- /dev/null
+++ b/arch/arm/boot/dts/hpe-gxp.dtsi
@@ -0,0 +1,127 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device Tree file for HPE GXP
+ */
+
+/dts-v1/;
+/ {
+	model = "Hewlett Packard Enterprise GXP BMC";
+	compatible = "hpe,gxp";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu@0 {
+			compatible = "arm,cortex-a9";
+			reg = <0>;
+			device_type = "cpu";
+			next-level-cache = <&L2>;
+		};
+	};
+
+	clocks {
+		pll: clock-0 {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <1600000000>;
+		};
+
+		iopclk: clock-1 {
+			compatible = "fixed-factor-clock";
+			#clock-cells = <0>;
+			clock-div = <4>;
+			clock-mult = <1>;
+			clocks = <&pll>;
+		};
+	};
+
+	axi {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+		dma-ranges;
+
+		L2: cache-controller@b0040000 {
+			compatible = "arm,pl310-cache";
+			reg = <0xb0040000 0x1000>;
+			cache-unified;
+			cache-level = <2>;
+		};
+
+		ahb@c0000000 {
+			compatible = "simple-bus";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0xc0000000 0x30000000>;
+			dma-ranges;
+
+			vic0: interrupt-controller@eff0000 {
+				compatible = "arm,pl192-vic";
+				reg = <0xeff0000 0x1000>;
+				interrupt-controller;
+				#interrupt-cells = <1>;
+			};
+
+			vic1: interrupt-controller@80f00000 {
+				compatible = "arm,pl192-vic";
+				reg = <0x80f00000 0x1000>;
+				interrupt-controller;
+				#interrupt-cells = <1>;
+			};
+
+			uarta: serial@e0 {
+				compatible = "ns16550a";
+				reg = <0xe0 0x8>;
+				interrupts = <17>;
+				interrupt-parent = <&vic0>;
+				clock-frequency = <1846153>;
+				reg-shift = <0>;
+			};
+
+			uartb: serial@e8 {
+				compatible = "ns16550a";
+				reg = <0xe8 0x8>;
+				interrupts = <18>;
+				interrupt-parent = <&vic0>;
+				clock-frequency = <1846153>;
+				reg-shift = <0>;
+			};
+
+			uartc: serial@f0 {
+				compatible = "ns16550a";
+				reg = <0xf0 0x8>;
+				interrupts = <19>;
+				interrupt-parent = <&vic0>;
+				clock-frequency = <1846153>;
+				reg-shift = <0>;
+			};
+
+			usb0: usb@efe0000 {
+				compatible = "hpe,gxp-ehci", "generic-ehci";
+				reg = <0xefe0000 0x100>;
+				interrupts = <7>;
+				interrupt-parent = <&vic0>;
+			};
+
+			st: timer@80 {
+				compatible = "hpe,gxp-timer";
+				reg = <0x80 0x16>;
+				interrupts = <0>;
+				interrupt-parent = <&vic0>;
+				clocks = <&iopclk>;
+				clock-names = "iop";
+			};
+
+			usb1: usb@efe0100 {
+				compatible = "hpe,gxp-ohci", "generic-ohci";
+				reg = <0xefe0100 0x110>;
+				interrupts = <6>;
+				interrupt-parent = <&vic0>;
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/imx1-pinfunc.h b/arch/arm/boot/dts/imx1-pinfunc.h
index 050a1fc46a77..bd2e679cb26c 100644
--- a/arch/arm/boot/dts/imx1-pinfunc.h
+++ b/arch/arm/boot/dts/imx1-pinfunc.h
@@ -26,9 +26,9 @@
  *                2 - 0
  *                3 - 1
  *
- * 'pin' is an integer between 0 and 0xbf. i.MX1 has 4 ports with 32 configurable
- * configurable pins each. 'pin' is PORT * 32 + PORT_PIN, PORT_PIN is the pin
- * number on the specific port (between 0 and 31).
+ * 'pin' is an integer between 0 and 0xbf. i.MX1 has 4 ports with 32
+ * configurable pins each. 'pin' is PORT * 32 + PORT_PIN, PORT_PIN is
+ * the pin number on the specific port (between 0 and 31).
  */
 
 #define MX1_PAD_A24__A24			0x00 0x004
diff --git a/arch/arm/boot/dts/imx1.dtsi b/arch/arm/boot/dts/imx1.dtsi
index 9b940987864c..e312f1e74e2f 100644
--- a/arch/arm/boot/dts/imx1.dtsi
+++ b/arch/arm/boot/dts/imx1.dtsi
@@ -55,7 +55,7 @@
 
 	clocks {
 		clk32 {
-			compatible = "fsl,imx-clk32", "fixed-clock";
+			compatible = "fixed-clock";
 			#clock-cells = <0>;
 			clock-frequency = <32000>;
 		};
diff --git a/arch/arm/boot/dts/imx23-evk.dts b/arch/arm/boot/dts/imx23-evk.dts
index 8cbaf1c81174..3b609d987d88 100644
--- a/arch/arm/boot/dts/imx23-evk.dts
+++ b/arch/arm/boot/dts/imx23-evk.dts
@@ -79,7 +79,6 @@
 						MX23_PAD_LCD_RESET__GPIO_1_18
 						MX23_PAD_PWM3__GPIO_1_29
 						MX23_PAD_PWM4__GPIO_1_30
-						MX23_PAD_SSP1_DETECT__SSP1_DETECT
 					>;
 					fsl,drive-strength = <MXS_DRIVE_4mA>;
 					fsl,voltage = <MXS_VOLTAGE_HIGH>;
diff --git a/arch/arm/boot/dts/imx23-pinfunc.h b/arch/arm/boot/dts/imx23-pinfunc.h
index 5c0f32ca3a93..468c079f3c2b 100644
--- a/arch/arm/boot/dts/imx23-pinfunc.h
+++ b/arch/arm/boot/dts/imx23-pinfunc.h
@@ -1,14 +1,8 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * Header providing constants for i.MX23 pinctrl bindings.
  *
  * Copyright (C) 2013 Lothar Waßmann <LW@KARO-electronics.de>
- *
- * The code contained herein is licensed under the GNU General Public
- * License. You may obtain a copy of the GNU General Public License
- * Version 2 at the following locations:
- *
- * http://www.opensource.org/licenses/gpl-license.html
- * http://www.gnu.org/copyleft/gpl.html
  */
 
 #ifndef __DT_BINDINGS_MX23_PINCTRL_H__
diff --git a/arch/arm/boot/dts/imx23-xfi3.dts b/arch/arm/boot/dts/imx23-xfi3.dts
index a6213c590f94..b1d8210f3ecc 100644
--- a/arch/arm/boot/dts/imx23-xfi3.dts
+++ b/arch/arm/boot/dts/imx23-xfi3.dts
@@ -158,19 +158,19 @@
 		default-brightness-level = <6>;
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 		pinctrl-names = "default";
 		pinctrl-0 = <&key_pins_a>;
 
-		voldown {
+		key-voldown {
 			label = "volume-down";
 			linux,code = <114>;
 			gpios = <&gpio2 7 0>;
 			debounce-interval = <20>;
 		};
 
-		volup {
+		key-volup {
 			label = "volume-up";
 			linux,code = <115>;
 			gpios = <&gpio2 8 0>;
diff --git a/arch/arm/boot/dts/imx25-eukrea-mbimxsd25-baseboard.dts b/arch/arm/boot/dts/imx25-eukrea-mbimxsd25-baseboard.dts
index 3f38c2e60a74..c7207ea437c4 100644
--- a/arch/arm/boot/dts/imx25-eukrea-mbimxsd25-baseboard.dts
+++ b/arch/arm/boot/dts/imx25-eukrea-mbimxsd25-baseboard.dts
@@ -13,12 +13,12 @@
 	model = "Eukrea MBIMXSD25";
 	compatible = "eukrea,mbimxsd25-baseboard", "eukrea,cpuimx25", "fsl,imx25";
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gpiokeys>;
 
-		bp1 {
+		button {
 			label = "BP1";
 			gpios = <&gpio3 18 GPIO_ACTIVE_LOW>;
 			linux,code = <BTN_MISC>;
diff --git a/arch/arm/boot/dts/imx25.dtsi b/arch/arm/boot/dts/imx25.dtsi
index fdcca82c9986..5f90d72b840b 100644
--- a/arch/arm/boot/dts/imx25.dtsi
+++ b/arch/arm/boot/dts/imx25.dtsi
@@ -62,13 +62,13 @@
 
 	clocks {
 		osc {
-			compatible = "fsl,imx-osc", "fixed-clock";
+			compatible = "fixed-clock";
 			#clock-cells = <0>;
 			clock-frequency = <24000000>;
 		};
 	};
 
-	soc {
+	soc: soc {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "simple-bus";
@@ -200,7 +200,7 @@
 			};
 		};
 
-		spba@50000000 {
+		spba-bus@50000000 {
 			compatible = "fsl,spba-bus", "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -515,7 +515,7 @@
 				#interrupt-cells = <2>;
 			};
 
-			sdma: sdma@53fd4000 {
+			sdma: dma-controller@53fd4000 {
 				compatible = "fsl,imx25-sdma";
 				reg = <0x53fd4000 0x4000>;
 				clocks = <&clks 112>, <&clks 68>;
diff --git a/arch/arm/boot/dts/imx27-pinfunc.h b/arch/arm/boot/dts/imx27-pinfunc.h
index 1514d80a3112..75aea0c701d4 100644
--- a/arch/arm/boot/dts/imx27-pinfunc.h
+++ b/arch/arm/boot/dts/imx27-pinfunc.h
@@ -26,9 +26,9 @@
  *                2 - 0
  *                3 - 1
  *
- * 'pin' is an integer between 0 and 0xbf. imx27 has 6 ports with 32 configurable
- * configurable pins each. 'pin' is PORT * 32 + PORT_PIN, PORT_PIN is the pin
- * number on the specific port (between 0 and 31).
+ * 'pin' is an integer between 0 and 0xbf. imx27 has 6 ports with 32
+ * configurable pins each. 'pin' is PORT * 32 + PORT_PIN, PORT_PIN is
+ * the pin number on the specific port (between 0 and 31).
  */
 
 #define MX27_PAD_USBH2_CLK__USBH2_CLK                      0x00 0x000
diff --git a/arch/arm/boot/dts/imx27.dtsi b/arch/arm/boot/dts/imx27.dtsi
index fd525c3b16fa..e140307be2e7 100644
--- a/arch/arm/boot/dts/imx27.dtsi
+++ b/arch/arm/boot/dts/imx27.dtsi
@@ -74,14 +74,14 @@
 		};
 	};
 
-	soc {
+	soc: soc {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "simple-bus";
 		interrupt-parent = <&aitc>;
 		ranges;
 
-		aipi@10000000 { /* AIPI1 */
+		aipi1: aipi@10000000 { /* AIPI1 */
 			compatible = "fsl,aipi-bus", "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -96,7 +96,7 @@
 					 <&clks IMX27_CLK_DMA_AHB_GATE>;
 				clock-names = "ipg", "ahb";
 				#dma-cells = <1>;
-				#dma-channels = <16>;
+				dma-channels = <16>;
 			};
 
 			wdog: watchdog@10002000 {
@@ -453,7 +453,7 @@
 			};
 		};
 
-		aipi@10020000 { /* AIPI2 */
+		aipi2: aipi@10020000 { /* AIPI2 */
 			compatible = "fsl,aipi-bus", "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
diff --git a/arch/arm/boot/dts/imx28-cfa10049.dts b/arch/arm/boot/dts/imx28-cfa10049.dts
index a92b05ef390f..9ef0d567ea48 100644
--- a/arch/arm/boot/dts/imx28-cfa10049.dts
+++ b/arch/arm/boot/dts/imx28-cfa10049.dts
@@ -327,7 +327,7 @@
 		};
 	};
 
-	spi2 {
+	spi-2 {
 		compatible = "spi-gpio";
 		pinctrl-names = "default";
 		pinctrl-0 = <&spi2_pins_cfa10049>;
@@ -351,7 +351,7 @@
 		};
 	};
 
-	spi3 {
+	spi-3 {
 		compatible = "spi-gpio";
 		pinctrl-names = "default";
 		pinctrl-0 = <&spi3_pins_cfa10049>;
@@ -388,12 +388,12 @@
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 		pinctrl-names = "default";
 		pinctrl-0 = <&rotary_btn_pins_cfa10049>;
 
-		rotary_button {
+		rotary-button {
 			label = "rotary_button";
 			gpios = <&gpio3 26 1>;
 			debounce-interval = <10>;
diff --git a/arch/arm/boot/dts/imx28-cfa10055.dts b/arch/arm/boot/dts/imx28-cfa10055.dts
index d05c370dfc17..fac5bbda7a93 100644
--- a/arch/arm/boot/dts/imx28-cfa10055.dts
+++ b/arch/arm/boot/dts/imx28-cfa10055.dts
@@ -129,7 +129,7 @@
 		};
 	};
 
-	spi2 {
+	spi-2 {
 		compatible = "spi-gpio";
 		pinctrl-names = "default";
 		pinctrl-0 = <&spi2_pins_cfa10055>;
diff --git a/arch/arm/boot/dts/imx28-cfa10056.dts b/arch/arm/boot/dts/imx28-cfa10056.dts
index c1060bd5f17f..c5f3337e8b39 100644
--- a/arch/arm/boot/dts/imx28-cfa10056.dts
+++ b/arch/arm/boot/dts/imx28-cfa10056.dts
@@ -88,7 +88,7 @@
 		};
 	};
 
-	spi2 {
+	spi-2 {
 		compatible = "spi-gpio";
 		pinctrl-names = "default";
 		pinctrl-0 = <&spi2_pins_cfa10056>;
diff --git a/arch/arm/boot/dts/imx28-duckbill-2-enocean.dts b/arch/arm/boot/dts/imx28-duckbill-2-enocean.dts
index bacb846f99e3..73f521c46c1e 100644
--- a/arch/arm/boot/dts/imx28-duckbill-2-enocean.dts
+++ b/arch/arm/boot/dts/imx28-duckbill-2-enocean.dts
@@ -204,7 +204,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&enocean_button>;
 
-		enocean {
+		key-enocean {
 			label = "EnOcean";
 			linux,code = <KEY_NEW>;
 			gpios = <&gpio3 3 GPIO_ACTIVE_HIGH>;
diff --git a/arch/arm/boot/dts/imx28-eukrea-mbmx28lc.dtsi b/arch/arm/boot/dts/imx28-eukrea-mbmx28lc.dtsi
index 3280fddaaf0d..b285a946e2c2 100644
--- a/arch/arm/boot/dts/imx28-eukrea-mbmx28lc.dtsi
+++ b/arch/arm/boot/dts/imx28-eukrea-mbmx28lc.dtsi
@@ -19,12 +19,12 @@
 		default-brightness-level = <10>;
 	};
 
-	button-sw3 {
+	gpio-keys-0 {
 		compatible = "gpio-keys";
 		pinctrl-names = "default";
 		pinctrl-0 = <&gpio_button_sw3_pins_mbmx28lc>;
 
-		sw3 {
+		switch-sw3 {
 			label = "SW3";
 			gpios = <&gpio1 21 GPIO_ACTIVE_LOW>;
 			linux,code = <BTN_MISC>;
@@ -32,12 +32,12 @@
 		};
 	};
 
-	button-sw4 {
+	gpio-keys-1 {
 		compatible = "gpio-keys";
 		pinctrl-names = "default";
 		pinctrl-0 = <&gpio_button_sw4_pins_mbmx28lc>;
 
-		sw4 {
+		switch-sw4 {
 			label = "SW4";
 			gpios = <&gpio1 20 GPIO_ACTIVE_LOW>;
 			linux,code = <BTN_MISC>;
diff --git a/arch/arm/boot/dts/imx28-evk.dts b/arch/arm/boot/dts/imx28-evk.dts
index 7e2b0f198dfa..1053b7c584d8 100644
--- a/arch/arm/boot/dts/imx28-evk.dts
+++ b/arch/arm/boot/dts/imx28-evk.dts
@@ -129,7 +129,7 @@
 				pinctrl-0 = <&spi2_pins_a>;
 				status = "okay";
 
-				flash: m25p80@0 {
+				flash: flash@0 {
 					#address-cells = <1>;
 					#size-cells = <1>;
 					compatible = "sst,sst25vf016b", "jedec,spi-nor";
diff --git a/arch/arm/boot/dts/imx28-m28evk.dts b/arch/arm/boot/dts/imx28-m28evk.dts
index f3bddc5ada4b..13acdc7916b9 100644
--- a/arch/arm/boot/dts/imx28-m28evk.dts
+++ b/arch/arm/boot/dts/imx28-m28evk.dts
@@ -33,7 +33,7 @@
 				pinctrl-0 = <&spi2_pins_a>;
 				status = "okay";
 
-				flash: m25p80@0 {
+				flash: flash@0 {
 					#address-cells = <1>;
 					#size-cells = <1>;
 					compatible = "m25p80", "jedec,spi-nor";
diff --git a/arch/arm/boot/dts/imx28-pinfunc.h b/arch/arm/boot/dts/imx28-pinfunc.h
index e11f69ba0fe4..d427e6c2fa78 100644
--- a/arch/arm/boot/dts/imx28-pinfunc.h
+++ b/arch/arm/boot/dts/imx28-pinfunc.h
@@ -1,14 +1,8 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * Header providing constants for i.MX28 pinctrl bindings.
  *
  * Copyright (C) 2013 Lothar Waßmann <LW@KARO-electronics.de>
- *
- * The code contained herein is licensed under the GNU General Public
- * License. You may obtain a copy of the GNU General Public License
- * Version 2 at the following locations:
- *
- * http://www.opensource.org/licenses/gpl-license.html
- * http://www.gnu.org/copyleft/gpl.html
  */
 
 #ifndef __DT_BINDINGS_MX28_PINCTRL_H__
diff --git a/arch/arm/boot/dts/imx28-sps1.dts b/arch/arm/boot/dts/imx28-sps1.dts
index 43be7a6a769b..90928db0df70 100644
--- a/arch/arm/boot/dts/imx28-sps1.dts
+++ b/arch/arm/boot/dts/imx28-sps1.dts
@@ -51,7 +51,7 @@
 				pinctrl-0 = <&spi2_pins_a>;
 				status = "okay";
 
-				flash: m25p80@0 {
+				flash: flash@0 {
 					#address-cells = <1>;
 					#size-cells = <1>;
 					compatible = "everspin,mr25h256", "mr25h256";
diff --git a/arch/arm/boot/dts/imx28-ts4600.dts b/arch/arm/boot/dts/imx28-ts4600.dts
index 097ec35c62d8..0d58da1c0cc5 100644
--- a/arch/arm/boot/dts/imx28-ts4600.dts
+++ b/arch/arm/boot/dts/imx28-ts4600.dts
@@ -26,7 +26,7 @@
 				pinctrl-0 = <&mmc0_4bit_pins_a
 					     &mmc0_sck_cfg
 					     &en_sd_pwr>;
-				broken-cd = <1>;
+				broken-cd;
 				bus-width = <4>;
 				vmmc-supply = <&reg_vddio_sd0>;
 				status = "okay";
diff --git a/arch/arm/boot/dts/imx28-tx28.dts b/arch/arm/boot/dts/imx28-tx28.dts
index 164254c28f8e..096f246032c6 100644
--- a/arch/arm/boot/dts/imx28-tx28.dts
+++ b/arch/arm/boot/dts/imx28-tx28.dts
@@ -221,7 +221,7 @@
 		linux,no-autorepeat;
 	};
 
-	spi_gpio: spi-gpio {
+	spi_gpio: spi {
 		compatible = "spi-gpio";
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -239,24 +239,6 @@
 		>;
 		/* enable this and disable ssp3 below, if you need full duplex SPI transfer */
 		status = "disabled";
-
-		spi@0 {
-			compatible = "spidev";
-			reg = <0>;
-			spi-max-frequency = <57600000>;
-		};
-
-		spi@1 {
-			compatible = "spidev";
-			reg = <1>;
-			spi-max-frequency = <57600000>;
-		};
-
-		spi@2 {
-			compatible = "spidev";
-			reg = <2>;
-			spi-max-frequency = <57600000>;
-		};
 	};
 };
 
@@ -356,7 +338,7 @@
 	};
 
 	ds1339: rtc@68 {
-		compatible = "mxim,ds1339";
+		compatible = "dallas,ds1339";
 		reg = <0x68>;
 		trickle-resistor-ohms = <250>;
 		trickle-diode-disable;
@@ -700,24 +682,6 @@
 	pinctrl-0 = <&spi3_pins_a>;
 	clock-frequency = <57600000>;
 	status = "okay";
-
-	spi@0 {
-		compatible = "spidev";
-		reg = <0>;
-		spi-max-frequency = <57600000>;
-	};
-
-	spi@1 {
-		compatible = "spidev";
-		reg = <1>;
-		spi-max-frequency = <57600000>;
-	};
-
-	spi@2 {
-		compatible = "spidev";
-		reg = <2>;
-		spi-max-frequency = <57600000>;
-	};
 };
 
 &usb0 {
diff --git a/arch/arm/boot/dts/imx28.dtsi b/arch/arm/boot/dts/imx28.dtsi
index 84d0176d5193..130b4145af82 100644
--- a/arch/arm/boot/dts/imx28.dtsi
+++ b/arch/arm/boot/dts/imx28.dtsi
@@ -110,6 +110,8 @@
 				interrupt-names = "bch";
 				clocks = <&clks 50>;
 				clock-names = "gpmi_io";
+				assigned-clocks = <&clks 13>;
+				assigned-clock-parents = <&clks 10>;
 				dmas = <&dma_apbh 4>;
 				dma-names = "rx-tx";
 				status = "disabled";
diff --git a/arch/arm/boot/dts/imx31.dtsi b/arch/arm/boot/dts/imx31.dtsi
index 948d2a543f8d..95c05f17a6d5 100644
--- a/arch/arm/boot/dts/imx31.dtsi
+++ b/arch/arm/boot/dts/imx31.dtsi
@@ -48,7 +48,7 @@
 		reg = <0x68000000 0x100000>;
 	};
 
-	soc {
+	soc: soc {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "simple-bus";
@@ -63,7 +63,7 @@
 			ranges = <0 0x1fffc000 0x4000>;
 		};
 
-		bus@43f00000 { /* AIPS1 */
+		aips1: bus@43f00000 { /* AIPS1 */
 			compatible = "fsl,aips-bus", "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -166,7 +166,7 @@
 			};
 		};
 
-		spba@50000000 {
+		spba-bus@50000000 {
 			compatible = "fsl,spba-bus", "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -297,7 +297,7 @@
 				#interrupt-cells = <2>;
 			};
 
-			sdma: sdma@53fd4000 {
+			sdma: dma-controller@53fd4000 {
 				compatible = "fsl,imx31-sdma";
 				reg = <0x53fd4000 0x4000>;
 				interrupts = <34>;
diff --git a/arch/arm/boot/dts/imx35-eukrea-mbimxsd35-baseboard.dts b/arch/arm/boot/dts/imx35-eukrea-mbimxsd35-baseboard.dts
index b1c11170ac25..7f4f812b0811 100644
--- a/arch/arm/boot/dts/imx35-eukrea-mbimxsd35-baseboard.dts
+++ b/arch/arm/boot/dts/imx35-eukrea-mbimxsd35-baseboard.dts
@@ -13,12 +13,12 @@
 	model = "Eukrea CPUIMX35";
 	compatible = "eukrea,mbimxsd35-baseboard", "eukrea,cpuimx35", "fsl,imx35";
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_bp1>;
 
-		bp1 {
+		button {
 			label = "BP1";
 			gpios = <&gpio3 25 GPIO_ACTIVE_LOW>;
 			linux,code = <BTN_MISC>;
diff --git a/arch/arm/boot/dts/imx35.dtsi b/arch/arm/boot/dts/imx35.dtsi
index 8e41c8b7bd70..d650f54c3fc6 100644
--- a/arch/arm/boot/dts/imx35.dtsi
+++ b/arch/arm/boot/dts/imx35.dtsi
@@ -284,7 +284,7 @@
 				#interrupt-cells = <2>;
 			};
 
-			sdma: sdma@53fd4000 {
+			sdma: dma-controller@53fd4000 {
 				compatible = "fsl,imx35-sdma";
 				reg = <0x53fd4000 0x4000>;
 				clocks = <&clks 9>, <&clks 65>;
diff --git a/arch/arm/boot/dts/imx50-kobo-aura.dts b/arch/arm/boot/dts/imx50-kobo-aura.dts
index 82ce8c43be86..51bf6117fb12 100644
--- a/arch/arm/boot/dts/imx50-kobo-aura.dts
+++ b/arch/arm/boot/dts/imx50-kobo-aura.dts
@@ -38,20 +38,20 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gpiokeys>;
 
-		power {
+		key-power {
 			label = "Power Button";
 			gpios = <&gpio4 10 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
 		};
 
-		hallsensor {
+		event-hallsensor {
 			label = "Hallsensor";
 			gpios = <&gpio5 15 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_RESERVED>;
 			linux,input-type = <EV_SW>;
 		};
 
-		frontlight {
+		event-frontlight {
 			label = "Frontlight";
 			gpios = <&gpio4 1 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_DISPLAYTOGGLE>;
diff --git a/arch/arm/boot/dts/imx50.dtsi b/arch/arm/boot/dts/imx50.dtsi
index a969f335b240..3d9a9f37f672 100644
--- a/arch/arm/boot/dts/imx50.dtsi
+++ b/arch/arm/boot/dts/imx50.dtsi
@@ -62,25 +62,25 @@
 
 	clocks {
 		ckil {
-			compatible = "fsl,imx-ckil", "fixed-clock";
+			compatible = "fixed-clock";
 			#clock-cells = <0>;
 			clock-frequency = <32768>;
 		};
 
 		ckih1 {
-			compatible = "fsl,imx-ckih1", "fixed-clock";
+			compatible = "fixed-clock";
 			#clock-cells = <0>;
 			clock-frequency = <22579200>;
 		};
 
 		ckih2 {
-			compatible = "fsl,imx-ckih2", "fixed-clock";
+			compatible = "fixed-clock";
 			#clock-cells = <0>;
 			clock-frequency = <0>;
 		};
 
 		osc {
-			compatible = "fsl,imx-osc", "fixed-clock";
+			compatible = "fixed-clock";
 			#clock-cells = <0>;
 			clock-frequency = <24000000>;
 		};
@@ -94,21 +94,21 @@
 		status = "okay";
 	};
 
-	soc {
+	soc: soc {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "simple-bus";
 		interrupt-parent = <&tzic>;
 		ranges;
 
-		bus@50000000 { /* AIPS1 */
+		aips1: bus@50000000 { /* AIPS1 */
 			compatible = "fsl,aips-bus", "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
 			reg = <0x50000000 0x10000000>;
 			ranges;
 
-			spba@50000000 {
+			spba-bus@50000000 {
 				compatible = "fsl,spba-bus", "simple-bus";
 				#address-cells = <1>;
 				#size-cells = <1>;
@@ -385,7 +385,7 @@
 			};
 		};
 
-		bus@60000000 {	/* AIPS2 */
+		aips2: bus@60000000 {	/* AIPS2 */
 			compatible = "fsl,aips-bus", "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -421,7 +421,7 @@
 				status = "disabled";
 			};
 
-			sdma: sdma@63fb0000 {
+			sdma: dma-controller@63fb0000 {
 				compatible = "fsl,imx50-sdma", "fsl,imx35-sdma";
 				reg = <0x63fb0000 0x4000>;
 				interrupts = <6>;
diff --git a/arch/arm/boot/dts/imx51-apf51dev.dts b/arch/arm/boot/dts/imx51-apf51dev.dts
index c66f274ba4e9..b61d55ca1467 100644
--- a/arch/arm/boot/dts/imx51-apf51dev.dts
+++ b/arch/arm/boot/dts/imx51-apf51dev.dts
@@ -63,7 +63,7 @@
 	leds {
 		compatible = "gpio-leds";
 
-		user {
+		led-user {
 			label = "Heartbeat";
 			gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
diff --git a/arch/arm/boot/dts/imx51-babbage.dts b/arch/arm/boot/dts/imx51-babbage.dts
index 552196d8a60a..a1f9c6a72275 100644
--- a/arch/arm/boot/dts/imx51-babbage.dts
+++ b/arch/arm/boot/dts/imx51-babbage.dts
@@ -154,7 +154,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gpio_keys>;
 
-		power {
+		key-power {
 			label = "Power Button";
 			gpios = <&gpio2 21 GPIO_ACTIVE_HIGH>;
 			linux,code = <KEY_POWER>;
diff --git a/arch/arm/boot/dts/imx51-digi-connectcore-jsk.dts b/arch/arm/boot/dts/imx51-digi-connectcore-jsk.dts
index aab8d6f137c3..10cae7c3a879 100644
--- a/arch/arm/boot/dts/imx51-digi-connectcore-jsk.dts
+++ b/arch/arm/boot/dts/imx51-digi-connectcore-jsk.dts
@@ -13,6 +13,13 @@
 	chosen {
 		stdout-path = &uart1;
 	};
+
+	usbphy1: usbphy1 {
+		compatible = "usb-nop-xceiv";
+		clocks = <&clks IMX5_CLK_USB_PHY_GATE>;
+		clock-names = "main_clk";
+		#phy-cells = <0>;
+	};
 };
 
 &esdhc1 {
@@ -63,6 +70,7 @@
 &usbh1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usbh1>;
+	fsl,usbphy = <&usbphy1>;
 	dr_mode = "host";
 	phy_type = "ulpi";
 	disable-over-current;
diff --git a/arch/arm/boot/dts/imx51-digi-connectcore-som.dtsi b/arch/arm/boot/dts/imx51-digi-connectcore-som.dtsi
index 7d4970417dce..f0809a16a2ce 100644
--- a/arch/arm/boot/dts/imx51-digi-connectcore-som.dtsi
+++ b/arch/arm/boot/dts/imx51-digi-connectcore-som.dtsi
@@ -34,22 +34,22 @@
 
 		regulators {
 			sw1_reg: sw1 {
-				regulator-min-microvolt = <1000000>;
+				regulator-min-microvolt = <1050000>;
 				regulator-max-microvolt = <1100000>;
 				regulator-boot-on;
 				regulator-always-on;
 			};
 
 			sw2_reg: sw2 {
-				regulator-min-microvolt = <1225000>;
-				regulator-max-microvolt = <1225000>;
+				regulator-min-microvolt = <1175000>;
+				regulator-max-microvolt = <1275000>;
 				regulator-boot-on;
 				regulator-always-on;
 			};
 
 			sw3_reg: sw3 {
-				regulator-min-microvolt = <1200000>;
-				regulator-max-microvolt = <1200000>;
+				regulator-min-microvolt = <1150000>;
+				regulator-max-microvolt = <1350000>;
 				regulator-boot-on;
 				regulator-always-on;
 			};
@@ -102,18 +102,6 @@
 				regulator-always-on;
 			};
 
-			vgen1_reg: vgen1 {
-				regulator-min-microvolt = <1200000>;
-				regulator-max-microvolt = <1200000>;
-				regulator-always-on;
-			};
-
-			vgen2_reg: vgen2 {
-				regulator-min-microvolt = <3150000>;
-				regulator-max-microvolt = <3150000>;
-				regulator-always-on;
-			};
-
 			vgen3_reg: vgen3 {
 				regulator-min-microvolt = <1800000>;
 				regulator-max-microvolt = <1800000>;
@@ -124,8 +112,6 @@
 				regulator-always-on;
 			};
 
-			gpo1_reg: gpo1 { };
-
 			gpo2_reg: gpo2 { };
 
 			gpo3_reg: gpo3 { };
@@ -198,6 +184,7 @@
 &usbotg {
 	phy_type = "utmi_wide";
 	disable-over-current;
+	vbus-supply = <&swbst_reg>;
 	/* Device role is not known, keep status disabled */
 };
 
diff --git a/arch/arm/boot/dts/imx51-ts4800.dts b/arch/arm/boot/dts/imx51-ts4800.dts
index 6ecb83e7f336..f7408722d68a 100644
--- a/arch/arm/boot/dts/imx51-ts4800.dts
+++ b/arch/arm/boot/dts/imx51-ts4800.dts
@@ -102,7 +102,7 @@
 	pinctrl-0 = <&pinctrl_i2c2>;
 	status = "okay";
 
-	rtc: m41t00@68 {
+	rtc: rtc@68 {
 		compatible = "st,m41t00";
 		reg = <0x68>;
 	};
@@ -174,7 +174,7 @@
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_interrupt_fpga>;
 			interrupt-parent = <&gpio2>;
-			interrupts= <9 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <9 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-controller;
 			#interrupt-cells = <1>;
 		};
diff --git a/arch/arm/boot/dts/imx51-zii-rdu1.dts b/arch/arm/boot/dts/imx51-zii-rdu1.dts
index ec8ca3ac2c1c..3140f038aa98 100644
--- a/arch/arm/boot/dts/imx51-zii-rdu1.dts
+++ b/arch/arm/boot/dts/imx51-zii-rdu1.dts
@@ -137,7 +137,7 @@
 		};
 	};
 
-	spi_gpio: spi-gpio {
+	spi_gpio: spi {
 		compatible = "spi-gpio";
 		#address-cells = <1>;
 		#size-cells = <0>;
diff --git a/arch/arm/boot/dts/imx51.dtsi b/arch/arm/boot/dts/imx51.dtsi
index 01cfcbe5928e..853707574d2e 100644
--- a/arch/arm/boot/dts/imx51.dtsi
+++ b/arch/arm/boot/dts/imx51.dtsi
@@ -48,25 +48,25 @@
 
 	clocks {
 		ckil {
-			compatible = "fsl,imx-ckil", "fixed-clock";
+			compatible = "fixed-clock";
 			#clock-cells = <0>;
 			clock-frequency = <32768>;
 		};
 
 		ckih1 {
-			compatible = "fsl,imx-ckih1", "fixed-clock";
+			compatible = "fixed-clock";
 			#clock-cells = <0>;
 			clock-frequency = <0>;
 		};
 
 		ckih2 {
-			compatible = "fsl,imx-ckih2", "fixed-clock";
+			compatible = "fixed-clock";
 			#clock-cells = <0>;
 			clock-frequency = <0>;
 		};
 
 		osc {
-			compatible = "fsl,imx-osc", "fixed-clock";
+			compatible = "fixed-clock";
 			#clock-cells = <0>;
 			clock-frequency = <24000000>;
 		};
@@ -114,7 +114,7 @@
 		ports = <&ipu_di0>, <&ipu_di1>;
 	};
 
-	soc {
+	soc: soc {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "simple-bus";
@@ -171,14 +171,14 @@
 			};
 		};
 
-		bus@70000000 { /* AIPS1 */
+		aips1: bus@70000000 { /* AIPS1 */
 			compatible = "fsl,aips-bus", "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
 			reg = <0x70000000 0x10000000>;
 			ranges;
 
-			spba@70000000 {
+			spba-bus@70000000 {
 				compatible = "fsl,spba-bus", "simple-bus";
 				#address-cells = <1>;
 				#size-cells = <1>;
@@ -215,6 +215,8 @@
 					clocks = <&clks IMX5_CLK_UART3_IPG_GATE>,
 						 <&clks IMX5_CLK_UART3_PER_GATE>;
 					clock-names = "ipg", "per";
+					dmas = <&sdma 43 5 1>, <&sdma 44 5 2>;
+					dma-names = "rx", "tx";
 					status = "disabled";
 				};
 
@@ -426,6 +428,8 @@
 				clocks = <&clks IMX5_CLK_UART1_IPG_GATE>,
 					 <&clks IMX5_CLK_UART1_PER_GATE>;
 				clock-names = "ipg", "per";
+				dmas = <&sdma 18 4 1>, <&sdma 19 4 2>;
+				dma-names = "rx", "tx";
 				status = "disabled";
 			};
 
@@ -436,6 +440,8 @@
 				clocks = <&clks IMX5_CLK_UART2_IPG_GATE>,
 					 <&clks IMX5_CLK_UART2_PER_GATE>;
 				clock-names = "ipg", "per";
+				dmas = <&sdma 16 4 1>, <&sdma 17 4 2>;
+				dma-names = "rx", "tx";
 				status = "disabled";
 			};
 
@@ -454,7 +460,7 @@
 			};
 		};
 
-		bus@80000000 {	/* AIPS2 */
+		aips2: bus@80000000 {	/* AIPS2 */
 			compatible = "fsl,aips-bus", "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -498,7 +504,7 @@
 				status = "disabled";
 			};
 
-			sdma: sdma@83fb0000 {
+			sdma: dma-controller@83fb0000 {
 				compatible = "fsl,imx51-sdma", "fsl,imx35-sdma";
 				reg = <0x83fb0000 0x4000>;
 				interrupts = <6>;
diff --git a/arch/arm/boot/dts/imx53-ard.dts b/arch/arm/boot/dts/imx53-ard.dts
index 6208fbb2e741..23a7492e2929 100644
--- a/arch/arm/boot/dts/imx53-ard.dts
+++ b/arch/arm/boot/dts/imx53-ard.dts
@@ -61,34 +61,34 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		home {
+		key-home {
 			label = "Home";
 			gpios = <&gpio5 10 0>;
 			linux,code = <KEY_HOME>;
 			wakeup-source;
 		};
 
-		back {
+		key-back {
 			label = "Back";
 			gpios = <&gpio5 11 0>;
 			linux,code = <KEY_BACK>;
 			wakeup-source;
 		};
 
-		program {
+		key-program {
 			label = "Program";
 			gpios = <&gpio5 12 0>;
 			linux,code = <KEY_PROGRAM >;
 			wakeup-source;
 		};
 
-		volume-up {
+		key-volume-up {
 			label = "Volume Up";
 			gpios = <&gpio5 13 0>;
 			linux,code = <KEY_VOLUMEUP>;
 		};
 
-		volume-down {
+		key-volume-down {
 			label = "Volume Down";
 			gpios = <&gpio4 0 0>;
 			linux,code = <KEY_VOLUMEDOWN>;
diff --git a/arch/arm/boot/dts/imx53-m53menlo.dts b/arch/arm/boot/dts/imx53-m53menlo.dts
index 4f88e96d81dd..d5c68d1ea707 100644
--- a/arch/arm/boot/dts/imx53-m53menlo.dts
+++ b/arch/arm/boot/dts/imx53-m53menlo.dts
@@ -53,6 +53,31 @@
 		};
 	};
 
+	lvds-decoder {
+		compatible = "ti,ds90cf364a", "lvds-decoder";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				lvds_decoder_in: endpoint {
+					remote-endpoint = <&lvds0_out>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				lvds_decoder_out: endpoint {
+					remote-endpoint = <&panel_in>;
+				};
+			};
+		};
+	};
+
 	panel {
 		compatible = "edt,etm0700g0dh6";
 		pinctrl-0 = <&pinctrl_display_gpio>;
@@ -61,7 +86,7 @@
 
 		port {
 			panel_in: endpoint {
-				remote-endpoint = <&lvds0_out>;
+				remote-endpoint = <&lvds_decoder_out>;
 			};
 		};
 	};
@@ -450,7 +475,7 @@
 			reg = <2>;
 
 			lvds0_out: endpoint {
-				remote-endpoint = <&panel_in>;
+				remote-endpoint = <&lvds_decoder_in>;
 			};
 		};
 	};
diff --git a/arch/arm/boot/dts/imx53-qsb-common.dtsi b/arch/arm/boot/dts/imx53-qsb-common.dtsi
index fe4244044a0f..50fef8dd3675 100644
--- a/arch/arm/boot/dts/imx53-qsb-common.dtsi
+++ b/arch/arm/boot/dts/imx53-qsb-common.dtsi
@@ -45,20 +45,20 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		power {
+		key-power {
 			label = "Power Button";
 			gpios = <&gpio1 8 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
 		};
 
-		volume-up {
+		key-volume-up {
 			label = "Volume Up";
 			gpios = <&gpio2 14 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_VOLUMEUP>;
 			wakeup-source;
 		};
 
-		volume-down {
+		key-volume-down {
 			label = "Volume Down";
 			gpios = <&gpio2 15 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_VOLUMEDOWN>;
@@ -71,7 +71,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&led_pin_gpio7_7>;
 
-		user {
+		led-user {
 			label = "Heartbeat";
 			gpios = <&gpio7 7 0>;
 			linux,default-trigger = "heartbeat";
diff --git a/arch/arm/boot/dts/imx53-smd.dts b/arch/arm/boot/dts/imx53-smd.dts
index 9be44e807188..f8d17967a67e 100644
--- a/arch/arm/boot/dts/imx53-smd.dts
+++ b/arch/arm/boot/dts/imx53-smd.dts
@@ -19,13 +19,13 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		volume-up {
+		key-volume-up {
 			label = "Volume Up";
 			gpios = <&gpio2 14 0>;
 			linux,code = <KEY_VOLUMEUP>;
 		};
 
-		volume-down {
+		key-volume-down {
 			label = "Volume Down";
 			gpios = <&gpio2 15 0>;
 			linux,code = <KEY_VOLUMEDOWN>;
diff --git a/arch/arm/boot/dts/imx53-tx53.dtsi b/arch/arm/boot/dts/imx53-tx53.dtsi
index 7c9730f3f820..892dd1a4bac3 100644
--- a/arch/arm/boot/dts/imx53-tx53.dtsi
+++ b/arch/arm/boot/dts/imx53-tx53.dtsi
@@ -81,7 +81,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gpio_key>;
 
-		power {
+		key-power {
 			label = "Power Button";
 			gpios = <&gpio5 2 GPIO_ACTIVE_HIGH>;
 			linux,code = <116>; /* KEY_POWER */
@@ -192,17 +192,6 @@
 		&gpio3 19 GPIO_ACTIVE_HIGH
 	>;
 
-	spidev0: spi@0 {
-		compatible = "spidev";
-		reg = <0>;
-		spi-max-frequency = <54000000>;
-	};
-
-	spidev1: spi@1 {
-		compatible = "spidev";
-		reg = <1>;
-		spi-max-frequency = <54000000>;
-	};
 };
 
 &esdhc1 {
@@ -252,7 +241,7 @@
 	clock-frequency = <400000>;
 	status = "okay";
 
-	rtc1: ds1339@68 {
+	rtc1: rtc@68 {
 		compatible = "dallas,ds1339";
 		reg = <0x68>;
 		pinctrl-names = "default";
diff --git a/arch/arm/boot/dts/imx53.dtsi b/arch/arm/boot/dts/imx53.dtsi
index 2cf3909cca2f..56b3c13f4eb7 100644
--- a/arch/arm/boot/dts/imx53.dtsi
+++ b/arch/arm/boot/dts/imx53.dtsi
@@ -86,25 +86,25 @@
 
 	clocks {
 		ckil {
-			compatible = "fsl,imx-ckil", "fixed-clock";
+			compatible = "fixed-clock";
 			#clock-cells = <0>;
 			clock-frequency = <32768>;
 		};
 
 		ckih1 {
-			compatible = "fsl,imx-ckih1", "fixed-clock";
+			compatible = "fixed-clock";
 			#clock-cells = <0>;
 			clock-frequency = <22579200>;
 		};
 
 		ckih2 {
-			compatible = "fsl,imx-ckih2", "fixed-clock";
+			compatible = "fixed-clock";
 			#clock-cells = <0>;
 			clock-frequency = <0>;
 		};
 
 		osc {
-			compatible = "fsl,imx-osc", "fixed-clock";
+			compatible = "fixed-clock";
 			#clock-cells = <0>;
 			clock-frequency = <24000000>;
 		};
@@ -132,7 +132,7 @@
 		status = "okay";
 	};
 
-	soc {
+	soc: soc {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "simple-bus";
@@ -222,14 +222,14 @@
 			clock-names = "core_clk", "mem_iface_clk";
 		};
 
-		bus@50000000 { /* AIPS1 */
+		aips1: bus@50000000 { /* AIPS1 */
 			compatible = "fsl,aips-bus", "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
 			reg = <0x50000000 0x10000000>;
 			ranges;
 
-			spba@50000000 {
+			spba-bus@50000000 {
 				compatible = "fsl,spba-bus", "simple-bus";
 				#address-cells = <1>;
 				#size-cells = <1>;
@@ -655,7 +655,7 @@
 			};
 		};
 
-		bus@60000000 {	/* AIPS2 */
+		aips2: bus@60000000 {	/* AIPS2 */
 			compatible = "fsl,aips-bus", "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -710,7 +710,7 @@
 				status = "disabled";
 			};
 
-			sdma: sdma@63fb0000 {
+			sdma: dma-controller@63fb0000 {
 				compatible = "fsl,imx53-sdma", "fsl,imx35-sdma";
 				reg = <0x63fb0000 0x4000>;
 				interrupts = <6>;
diff --git a/arch/arm/boot/dts/imx6-logicpd-baseboard.dtsi b/arch/arm/boot/dts/imx6-logicpd-baseboard.dtsi
index d9de9b4f0c52..d477a937b47a 100644
--- a/arch/arm/boot/dts/imx6-logicpd-baseboard.dtsi
+++ b/arch/arm/boot/dts/imx6-logicpd-baseboard.dtsi
@@ -6,7 +6,7 @@
 	keyboard {
 		compatible = "gpio-keys";
 
-		btn0 {
+		button-0 {
 			gpios = <&pcf8575 0 GPIO_ACTIVE_LOW>;
 			label = "btn0";
 			linux,code = <KEY_WAKEUP>;
@@ -14,7 +14,7 @@
 			wakeup-source;
 		};
 
-		btn1 {
+		button-1 {
 			gpios = <&pcf8575 1 GPIO_ACTIVE_LOW>;
 			label = "btn1";
 			linux,code = <KEY_WAKEUP>;
@@ -22,7 +22,7 @@
 			wakeup-source;
 		};
 
-		btn2 {
+		button-2 {
 			gpios = <&pcf8575 2 GPIO_ACTIVE_LOW>;
 			label = "btn2";
 			linux,code = <KEY_WAKEUP>;
@@ -30,7 +30,7 @@
 			wakeup-source;
 		};
 
-		btn3 {
+		button-3 {
 			gpios = <&pcf8575 3 GPIO_ACTIVE_LOW>;
 			label = "btn3";
 			linux,code = <KEY_WAKEUP>;
diff --git a/arch/arm/boot/dts/imx6dl-b1x5pv2.dtsi b/arch/arm/boot/dts/imx6dl-b1x5pv2.dtsi
index ec5b66453156..337db29b0010 100644
--- a/arch/arm/boot/dts/imx6dl-b1x5pv2.dtsi
+++ b/arch/arm/boot/dts/imx6dl-b1x5pv2.dtsi
@@ -188,7 +188,7 @@
 	rotary-encoder-key {
 		compatible = "gpio-keys";
 
-		rotary-encoder-press {
+		rotary-encoder-event {
 			label = "rotary-encoder press";
 			gpios = <&tca6424a 0 GPIO_ACTIVE_HIGH>;
 			linux,code = <KEY_ENTER>;
diff --git a/arch/arm/boot/dts/imx6dl-colibri-aster.dts b/arch/arm/boot/dts/imx6dl-colibri-aster.dts
new file mode 100644
index 000000000000..74e8a6cd8bed
--- /dev/null
+++ b/arch/arm/boot/dts/imx6dl-colibri-aster.dts
@@ -0,0 +1,113 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include "imx6dl.dtsi"
+#include "imx6qdl-colibri.dtsi"
+
+/ {
+	model = "Toradex Colibri iMX6DL/S on Colibri Aster Board";
+	compatible = "toradex,colibri_imx6dl-aster", "toradex,colibri_imx6dl",
+		     "fsl,imx6dl";
+
+	aliases {
+		i2c0 = &i2c2;
+		i2c1 = &i2c3;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
+
+/* Colibri SSP */
+&ecspi4 {
+	cs-gpios = <
+		&gpio5 2 GPIO_ACTIVE_HIGH
+		&gpio5 4 GPIO_ACTIVE_HIGH
+	>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi4 &pinctrl_csi_gpio_2>;
+	status = "okay";
+};
+
+/* Colibri I2C: I2C3_SDA/SCL on SODIMM 194/196 */
+&i2c3 {
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <
+		&pinctrl_csi_gpio_1
+		&pinctrl_gpio_2
+		&pinctrl_gpio_aster
+		&pinctrl_usbh_oc_1
+		&pinctrl_usbc_id_1
+		&pinctrl_weim_gpio_5
+	>;
+
+	pinctrl_gpio_aster: gpioaster {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL2__GPIO4_IO10		0x1b0b0
+			MX6QDL_PAD_KEY_ROW2__GPIO4_IO11		0x1b0b0
+			MX6QDL_PAD_KEY_ROW4__GPIO4_IO15		0x1b0b0
+			MX6QDL_PAD_NANDF_D1__GPIO2_IO01		0x1b0b0
+			MX6QDL_PAD_NANDF_D3__GPIO2_IO03		0x1b0b0
+			MX6QDL_PAD_NANDF_D6__GPIO2_IO06		0x1b0b0
+			MX6QDL_PAD_SD4_DAT0__GPIO2_IO08		0x1b0b0
+			MX6QDL_PAD_SD4_DAT3__GPIO2_IO11		0x1b0b0
+		>;
+	};
+};
+
+&pwm1 {
+	status = "okay";
+};
+
+&pwm2 {
+	status = "okay";
+};
+
+&pwm3 {
+	status = "okay";
+};
+
+&pwm4 {
+	status = "okay";
+};
+
+&reg_usb_host_vbus {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&uart3 {
+	status = "okay";
+};
+
+&usbh1 {
+	vbus-supply = <&reg_usb_host_vbus>;
+	status = "okay";
+};
+
+&usbotg {
+	status = "okay";
+};
+
+/* Colibri MMC */
+&usdhc1 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6dl-colibri-eval-v3.dts b/arch/arm/boot/dts/imx6dl-colibri-eval-v3.dts
index 7da74e6f46d9..7272edd85a49 100644
--- a/arch/arm/boot/dts/imx6dl-colibri-eval-v3.dts
+++ b/arch/arm/boot/dts/imx6dl-colibri-eval-v3.dts
@@ -1,6 +1,6 @@
-// SPDX-License-Identifier: GPL-2.0+ OR MIT
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
 /*
- * Copyright 2014-2020 Toradex
+ * Copyright 2014-2022 Toradex
  * Copyright 2012 Freescale Semiconductor, Inc.
  * Copyright 2011 Linaro Ltd.
  */
@@ -17,12 +17,6 @@
 	compatible = "toradex,colibri_imx6dl-eval-v3", "toradex,colibri_imx6dl",
 		     "fsl,imx6dl";
 
-	/* Will be filled by the bootloader */
-	memory@10000000 {
-		device_type = "memory";
-		reg = <0x10000000 0>;
-	};
-
 	aliases {
 		i2c0 = &i2c2;
 		i2c1 = &i2c3;
@@ -44,67 +38,6 @@
 		clock-frequency = <16000000>;
 		clock-output-names = "clk16m";
 	};
-
-	gpio-keys {
-		compatible = "gpio-keys";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_gpio_keys>;
-
-		wakeup {
-			label = "Wake-Up";
-			gpios = <&gpio2 22 GPIO_ACTIVE_HIGH>; /* SODIMM 45 */
-			linux,code = <KEY_WAKEUP>;
-			debounce-interval = <10>;
-			wakeup-source;
-		};
-	};
-
-	lcd_display: disp0 {
-		compatible = "fsl,imx-parallel-display";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		interface-pix-fmt = "bgr666";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_ipu1_lcdif>;
-		status = "okay";
-
-		port@0 {
-			reg = <0>;
-
-			lcd_display_in: endpoint {
-				remote-endpoint = <&ipu1_di0_disp0>;
-			};
-		};
-
-		port@1 {
-			reg = <1>;
-
-			lcd_display_out: endpoint {
-				remote-endpoint = <&lcd_panel_in>;
-			};
-		};
-	};
-
-	panel: panel {
-		/*
-		 * edt,et057090dhu: EDT 5.7" LCD TFT
-		 * edt,et070080dh6: EDT 7.0" LCD TFT
-		 */
-		compatible = "edt,et057090dhu";
-		backlight = <&backlight>;
-
-		port {
-			lcd_panel_in: endpoint {
-				remote-endpoint = <&lcd_display_out>;
-			};
-		};
-	};
-};
-
-&backlight {
-	brightness-levels = <0 127 191 223 239 247 251 255>;
-	default-brightness-level = <1>;
-	status = "okay";
 };
 
 /* Colibri SSP */
@@ -113,40 +46,21 @@
 
 	mcp251x0: mcp251x@0 {
 		compatible = "microchip,mcp2515";
-		reg = <0>;
 		clocks = <&clk16m>;
 		interrupt-parent = <&gpio3>;
 		interrupts = <27 0x2>;
+		reg = <0>;
 		spi-max-frequency = <10000000>;
 		status = "okay";
 	};
 };
 
-&hdmi {
-	status = "okay";
-};
-
 /*
  * Colibri I2C: I2C3_SDA/SCL on SODIMM 194/196 (e.g. RTC on carrier board)
  */
 &i2c3 {
 	status = "okay";
 
-	/*
-	 * Touchscreen is using SODIMM 28/30, also used for PWM<B>, PWM<C>,
-	 * aka pwm2, pwm3. so if you enable touchscreen, disable the pwms
-	 */
-	touchscreen@4a {
-		compatible = "atmel,maxtouch";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_pcap_1>;
-		reg = <0x4a>;
-		interrupt-parent = <&gpio1>;
-		interrupts = <9 IRQ_TYPE_EDGE_FALLING>;		/* SODIMM 28 */
-		reset-gpios = <&gpio2 10 GPIO_ACTIVE_LOW>;	/* SODIMM 30 */
-		status = "disabled";
-	};
-
 	/* M41T0M6 real time clock on carrier board */
 	rtc_i2c: rtc@68 {
 		compatible = "st,m41t0";
@@ -162,24 +76,6 @@
 		&pinctrl_weim_gpio_5 &pinctrl_weim_gpio_6
 		&pinctrl_usbh_oc_1 &pinctrl_usbc_id_1
 	>;
-
-	pinctrl_pcap_1: pcap1grp {
-		fsl,pins = <
-			MX6QDL_PAD_GPIO_9__GPIO1_IO09	0x1b0b0 /* SODIMM 28 */
-			MX6QDL_PAD_SD4_DAT2__GPIO2_IO10	0x1b0b0 /* SODIMM 30 */
-		>;
-	};
-
-	pinctrl_mxt_ts: mxttsgrp {
-		fsl,pins = <
-			MX6QDL_PAD_EIM_CS1__GPIO2_IO24	0x130b0 /* SODIMM 107 */
-			MX6QDL_PAD_SD2_DAT1__GPIO1_IO14	0x130b0 /* SODIMM 106 */
-		>;
-	};
-};
-
-&ipu1_di0_disp0 {
-	remote-endpoint = <&lcd_display_in>;
 };
 
 &pwm1 {
diff --git a/arch/arm/boot/dts/imx6dl-colibri-iris-v2.dts b/arch/arm/boot/dts/imx6dl-colibri-iris-v2.dts
new file mode 100644
index 000000000000..3a6d3889760d
--- /dev/null
+++ b/arch/arm/boot/dts/imx6dl-colibri-iris-v2.dts
@@ -0,0 +1,46 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/dts-v1/;
+
+#include "imx6dl-colibri-iris.dts"
+
+/ {
+	model = "Toradex Colibri iMX6DL/S on Colibri Iris V2 Board";
+	compatible = "toradex,colibri_imx6dl-iris-v2", "toradex,colibri_imx6dl",
+		     "fsl,imx6dl";
+
+	reg_3v3_vmmc: regulator-3v3-vmmc {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_enable_3v3_vmmc>;
+		regulator-name = "3v3_vmmc";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio2 11 GPIO_ACTIVE_HIGH>;
+		startup-delay-us = <100>;
+		enable-active-high;
+	};
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpio_iris	&pinctrl_usbh_oc_1 &pinctrl_usbc_id_1>;
+
+	pinctrl_enable_3v3_vmmc: enable3v3vmmcgrp {
+		fsl,pins = <
+			MX6QDL_PAD_SD4_DAT3__GPIO2_IO11	0x1b0b0
+		>;
+	};
+};
+
+/* Colibri MMC */
+&usdhc1 {
+	cap-power-off-card;
+	/* uncomment the following to enable SD card UHS mode if you have a V1.1 module */
+	/* /delete-property/ no-1-8-v; */
+	vmmc-supply = <&reg_3v3_vmmc>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6dl-colibri-iris.dts b/arch/arm/boot/dts/imx6dl-colibri-iris.dts
new file mode 100644
index 000000000000..cf77d894f6d7
--- /dev/null
+++ b/arch/arm/boot/dts/imx6dl-colibri-iris.dts
@@ -0,0 +1,152 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include "imx6dl.dtsi"
+#include "imx6qdl-colibri.dtsi"
+
+/ {
+	model = "Toradex Colibri iMX6DL/S on Colibri Iris Board";
+	compatible = "toradex,colibri_imx6dl-iris", "toradex,colibri_imx6dl",
+		     "fsl,imx6dl";
+
+	aliases {
+		i2c0 = &i2c2;
+		i2c1 = &i2c3;
+	};
+
+	aliases {
+		rtc0 = &rtc_i2c;
+		rtc1 = &snvs_rtc;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
+
+/* Colibri SSP */
+&ecspi4 {
+	status = "okay";
+};
+
+&gpio2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1_forceoff &pinctrl_uart23_forceoff>;
+
+	/*
+	 * uart-a-on-x13-enable turns the UART transceiver for UART_A on. If one
+	 * wants to turn the transceiver off, that property has to be deleted
+	 * and the gpio handled in userspace.
+	 * The same applies to uart-b-c-on-x14-enable where the UART_B and
+	 * UART_C transceiver is turned on.
+	 */
+	uart-a-on-x13-enable-hog {
+		gpio-hog;
+		gpios = <4 GPIO_ACTIVE_HIGH>; /* SODIMM 102 */
+		output-high;
+	};
+
+	uart-b-c-on-x14-enable-hog {
+		gpio-hog;
+		gpios = <8 GPIO_ACTIVE_HIGH>; /* SODIMM 104 */
+		output-high;
+	};
+};
+
+/*
+ * Colibri I2C: I2C3_SDA/SCL on SODIMM 194/196 (e.g. RTC on carrier board)
+ */
+&i2c3 {
+	status = "okay";
+
+	rtc_i2c: rtc@68 {
+		compatible = "st,m41t0";
+		reg = <0x68>;
+	};
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <
+		&pinctrl_gpio_iris
+		&pinctrl_usbh_oc_1
+		&pinctrl_usbc_id_1
+	>;
+
+	pinctrl_gpio_iris: gpioirisgrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_A17__GPIO2_IO21	0x1b0b0
+			MX6QDL_PAD_EIM_A18__GPIO2_IO20	0x1b0b0
+			MX6QDL_PAD_EIM_A19__GPIO2_IO19	0x1b0b0
+			MX6QDL_PAD_EIM_A20__GPIO2_IO18	0x1b0b0
+			MX6QDL_PAD_EIM_A23__GPIO6_IO06	0x1b0b0
+			MX6QDL_PAD_EIM_D27__GPIO3_IO27	0x1b0b0
+			MX6QDL_PAD_NANDF_D3__GPIO2_IO03	0x1b0b0
+			MX6QDL_PAD_SD2_DAT0__GPIO1_IO15	0x1b0b0
+		>;
+	};
+
+	pinctrl_uart1_forceoff: uart1forceoffgrp {
+		fsl,pins = <
+			MX6QDL_PAD_NANDF_D4__GPIO2_IO04 0x1b0b0
+		>;
+	};
+
+	pinctrl_uart23_forceoff: uart23forceoffgrp {
+		fsl,pins = <
+			MX6QDL_PAD_SD4_DAT0__GPIO2_IO08 0x1b0b0
+		>;
+	};
+};
+
+&pwm1 {
+	status = "okay";
+};
+
+&pwm2 {
+	status = "okay";
+};
+
+&pwm3 {
+	status = "okay";
+};
+
+&pwm4 {
+	status = "okay";
+};
+
+&reg_usb_host_vbus {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&uart3 {
+	status = "okay";
+};
+
+&usbh1 {
+	vbus-supply = <&reg_usb_host_vbus>;
+	status = "okay";
+};
+
+&usbotg {
+	status = "okay";
+};
+
+/* Colibri MMC */
+&usdhc1 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6dl-colibri-v1_1-eval-v3.dts b/arch/arm/boot/dts/imx6dl-colibri-v1_1-eval-v3.dts
deleted file mode 100644
index 223275f028f1..000000000000
--- a/arch/arm/boot/dts/imx6dl-colibri-v1_1-eval-v3.dts
+++ /dev/null
@@ -1,31 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+ OR MIT
-/*
- * Copyright 2020 Toradex
- */
-
-/dts-v1/;
-
-#include "imx6dl-colibri-eval-v3.dts"
-#include "imx6qdl-colibri-v1_1-uhs.dtsi"
-
-/ {
-	model = "Toradex Colibri iMX6DL/S V1.1 on Colibri Evaluation Board V3";
-	compatible = "toradex,colibri_imx6dl-v1_1-eval-v3",
-		     "toradex,colibri_imx6dl-v1_1",
-		     "toradex,colibri_imx6dl-eval-v3",
-		     "toradex,colibri_imx6dl",
-		     "fsl,imx6dl";
-};
-
-/* Colibri MMC */
-&usdhc1 {
-	status = "okay";
-	/*
-	 * Please make sure your carrier board does not pull-up any of
-	 * the MMC/SD signals to 3.3 volt before attempting to activate
-	 * UHS-I support.
-	 * To let signaling voltage be changed to 1.8V, please
-	 * delete no-1-8-v property (example below):
-	 * /delete-property/no-1-8-v;
-	 */
-};
diff --git a/arch/arm/boot/dts/imx6dl-eckelmann-ci4x10.dts b/arch/arm/boot/dts/imx6dl-eckelmann-ci4x10.dts
index b4a9523e325b..864dc5018451 100644
--- a/arch/arm/boot/dts/imx6dl-eckelmann-ci4x10.dts
+++ b/arch/arm/boot/dts/imx6dl-eckelmann-ci4x10.dts
@@ -297,7 +297,11 @@
 	phy-mode = "rmii";
 	phy-reset-gpios = <&gpio1 18 GPIO_ACTIVE_LOW>;
 	phy-handle = <&phy>;
-	clocks = <&clks IMX6QDL_CLK_ENET>, <&clks IMX6QDL_CLK_ENET>, <&rmii_clk>;
+	clocks = <&clks IMX6QDL_CLK_ENET>,
+		 <&clks IMX6QDL_CLK_ENET>,
+		 <&rmii_clk>,
+		 <&clks IMX6QDL_CLK_ENET_REF>;
+	clock-names = "ipg", "ahb", "ptp", "enet_out";
 	status = "okay";
 
 	mdio {
diff --git a/arch/arm/boot/dts/imx6dl-mba6.dtsi b/arch/arm/boot/dts/imx6dl-mba6.dtsi
new file mode 100644
index 000000000000..b749b424bbd6
--- /dev/null
+++ b/arch/arm/boot/dts/imx6dl-mba6.dtsi
@@ -0,0 +1,22 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright 2013 Sascha Hauer, Pengutronix
+ *
+ * Copyright 2013-2021 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+&ethphy {
+	rxdv-skew-ps = <180>;
+	txen-skew-ps = <0>;
+	rxd3-skew-ps = <180>;
+	rxd2-skew-ps = <180>;
+	rxd1-skew-ps = <180>;
+	rxd0-skew-ps = <180>;
+	txd3-skew-ps = <120>;
+	txd2-skew-ps = <0>;
+	txd1-skew-ps = <300>;
+	txd0-skew-ps = <120>;
+	txc-skew-ps = <1860>;
+	rxc-skew-ps = <1860>;
+};
diff --git a/arch/arm/boot/dts/imx6dl-mba6a.dts b/arch/arm/boot/dts/imx6dl-mba6a.dts
new file mode 100644
index 000000000000..df0a96b28af0
--- /dev/null
+++ b/arch/arm/boot/dts/imx6dl-mba6a.dts
@@ -0,0 +1,21 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright 2013 Sascha Hauer, Pengutronix
+ *
+ * Copyright 2013-2021 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include "imx6dl-tqma6a.dtsi"
+#include "imx6qdl-mba6.dtsi"
+#include "imx6qdl-mba6a.dtsi"
+#include "imx6dl-mba6.dtsi"
+
+/ {
+	model = "TQ TQMa6S/DL on MBa6x";
+	compatible = "tq,imx6dl-mba6x-a", "tq,mba6a",
+		     "tq,imx6dl-tqma6dl-a", "fsl,imx6dl";
+};
diff --git a/arch/arm/boot/dts/imx6dl-mba6b.dts b/arch/arm/boot/dts/imx6dl-mba6b.dts
new file mode 100644
index 000000000000..610b19d2db0f
--- /dev/null
+++ b/arch/arm/boot/dts/imx6dl-mba6b.dts
@@ -0,0 +1,21 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright 2013 Sascha Hauer, Pengutronix
+ *
+ * Copyright 2013-2021 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include "imx6dl-tqma6b.dtsi"
+#include "imx6qdl-mba6.dtsi"
+#include "imx6qdl-mba6b.dtsi"
+#include "imx6dl-mba6.dtsi"
+
+/ {
+	model = "TQ TQMa6S/DL on MBa6x";
+	compatible = "tq,imx6dl-mba6x-b", "tq,mba6b",
+		     "tq,imx6dl-tqma6dl-b", "fsl,imx6dl";
+};
diff --git a/arch/arm/boot/dts/imx6dl-phytec-mira-rdk-nand.dts b/arch/arm/boot/dts/imx6dl-phytec-mira-rdk-nand.dts
index 9f7f9f98139d..d906a7f05aaa 100644
--- a/arch/arm/boot/dts/imx6dl-phytec-mira-rdk-nand.dts
+++ b/arch/arm/boot/dts/imx6dl-phytec-mira-rdk-nand.dts
@@ -8,6 +8,9 @@
 #include "imx6dl.dtsi"
 #include "imx6qdl-phytec-phycore-som.dtsi"
 #include "imx6qdl-phytec-mira.dtsi"
+#include "imx6qdl-phytec-mira-peb-eval-01.dtsi"
+#include "imx6qdl-phytec-mira-peb-av-02.dtsi"
+#include "imx6qdl-phytec-mira-peb-wlbt-05.dtsi"
 
 / {
 	model = "PHYTEC phyBOARD-Mira DualLite/Solo Carrier-Board with NAND";
diff --git a/arch/arm/boot/dts/imx6dl-plybas.dts b/arch/arm/boot/dts/imx6dl-plybas.dts
index bf72a67a9c76..c52e6caf3996 100644
--- a/arch/arm/boot/dts/imx6dl-plybas.dts
+++ b/arch/arm/boot/dts/imx6dl-plybas.dts
@@ -214,7 +214,7 @@
 &uart2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart2>;
-	fsl,uart-has-rtscts;
+	uart-has-rtscts;
 	linux,rs485-enabled-at-boot-time;
 	rs485-rts-delay = <0 20>;
 	status = "okay";
diff --git a/arch/arm/boot/dts/imx6dl-plym2m.dts b/arch/arm/boot/dts/imx6dl-plym2m.dts
index 60fe5f14666e..522660c912a0 100644
--- a/arch/arm/boot/dts/imx6dl-plym2m.dts
+++ b/arch/arm/boot/dts/imx6dl-plym2m.dts
@@ -50,6 +50,11 @@
 		};
 	};
 
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&vdiv_vaccu>;
+	};
+
 	leds {
 		compatible = "gpio-leds";
 		pinctrl-names = "default";
@@ -101,6 +106,64 @@
 		regulator-min-microvolt = <12000000>;
 		regulator-max-microvolt = <12000000>;
 	};
+
+	thermal-zones {
+		chassis-thermal {
+			polling-delay = <20000>;
+			polling-delay-passive = <0>;
+			thermal-sensors = <&tsens0>;
+		};
+
+		touch-thermal0 {
+			polling-delay = <20000>;
+			polling-delay-passive = <0>;
+			thermal-sensors = <&touch_temp0>;
+		};
+
+		touch-thermal1 {
+			polling-delay = <20000>;
+			polling-delay-passive = <0>;
+			thermal-sensors = <&touch_temp1>;
+		};
+	};
+
+	touchscreen {
+		compatible = "resistive-adc-touch";
+		io-channels = <&adc_ts 1>, <&adc_ts 3>, <&adc_ts 4>,
+                              <&adc_ts 5>;
+		io-channel-names = "y", "z1", "z2", "x";
+		touchscreen-min-pressure = <64687>;
+		touchscreen-inverted-x;
+		touchscreen-inverted-y;
+		touchscreen-x-plate-ohms = <300>;
+		touchscreen-y-plate-ohms = <800>;
+	};
+
+	touch_temp0: touch-temperature-sensor0 {
+		compatible = "generic-adc-thermal";
+		#thermal-sensor-cells = <0>;
+		io-channels = <&adc_ts 0>;
+		io-channel-names = "sensor-channel";
+		temperature-lookup-table = <    (-40000) 736
+						85000 474>;
+	};
+
+	touch_temp1: touch-temperature-sensor1 {
+		compatible = "generic-adc-thermal";
+		#thermal-sensor-cells = <0>;
+		io-channels = <&adc_ts 7>;
+		io-channel-names = "sensor-channel";
+		temperature-lookup-table = <    (-40000) 826
+						85000 609>;
+	};
+
+	vdiv_vaccu: voltage-divider-vaccu {
+		compatible = "voltage-divider";
+		io-channels = <&adc_ts 2>;
+		output-ohms = <2500>;
+		full-ohms = <64000>;
+		#io-channel-cells = <0>;
+	};
 };
 
 &can1 {
@@ -129,26 +192,61 @@
 	pinctrl-0 = <&pinctrl_ecspi2>;
 	status = "okay";
 
-	touchscreen@0 {
-		compatible = "ti,tsc2046";
+	adc_ts: adc@0 {
+		compatible = "ti,tsc2046e-adc";
 		reg = <0>;
 		pinctrl-0 = <&pinctrl_tsc2046>;
-		pinctrl-names ="default";
-		spi-max-frequency = <100000>;
-		interrupts-extended = <&gpio3 20 IRQ_TYPE_EDGE_FALLING>;
-		pendown-gpio = <&gpio3 20 GPIO_ACTIVE_LOW>;
+		pinctrl-names = "default";
+		spi-max-frequency = <1000000>;
+		interrupts-extended = <&gpio3 20 IRQ_TYPE_LEVEL_LOW>;
+		#io-channel-cells = <1>;
 
-		touchscreen-inverted-x;
-		touchscreen-inverted-y;
-		touchscreen-max-pressure = <4095>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		channel@0 {
+			reg = <0>;
+			settling-time-us = <300>;
+			oversampling-ratio = <5>;
+		};
+
+		channel@1 {
+			reg = <1>;
+			settling-time-us = <700>;
+			oversampling-ratio = <5>;
+		};
 
-		ti,vref-delay-usecs = /bits/ 16 <100>;
-		ti,x-plate-ohms = /bits/ 16 <800>;
-		ti,y-plate-ohms = /bits/ 16 <300>;
-		ti,debounce-max = /bits/ 16 <3>;
-		ti,debounce-tol = /bits/ 16 <70>;
-		ti,debounce-rep = /bits/ 16 <3>;
-		wakeup-source;
+		channel@2 {
+			reg = <2>;
+			settling-time-us = <300>;
+			oversampling-ratio = <5>;
+		};
+
+		channel@3 {
+			reg = <3>;
+			settling-time-us = <700>;
+			oversampling-ratio = <5>;
+		};
+
+		channel@4 {
+			reg = <4>;
+			settling-time-us = <700>;
+			oversampling-ratio = <5>;
+		};
+
+		channel@5 {
+			reg = <5>;
+			settling-time-us = <700>;
+			oversampling-ratio = <5>;
+		};
+
+		/* channel 6 is not connected */
+
+		channel@7 {
+			reg = <7>;
+			settling-time-us = <300>;
+			oversampling-ratio = <5>;
+		};
 	};
 };
 
@@ -233,9 +331,10 @@
 	pinctrl-0 = <&pinctrl_i2c3>;
 	status = "okay";
 
-	temperature-sensor@70 {
+	tsens0: temperature-sensor@70 {
 		compatible = "ti,tmp103";
 		reg = <0x70>;
+		#thermal-sensor-cells = <0>;
 	};
 };
 
diff --git a/arch/arm/boot/dts/imx6dl-prtmvt.dts b/arch/arm/boot/dts/imx6dl-prtmvt.dts
index a35a1c66e770..1f8cddd83ccb 100644
--- a/arch/arm/boot/dts/imx6dl-prtmvt.dts
+++ b/arch/arm/boot/dts/imx6dl-prtmvt.dts
@@ -51,98 +51,98 @@
 		pinctrl-0 = <&pinctrl_gpiokeys>;
 		autorepeat;
 
-		power {
+		key-power {
 			label = "Power Button";
 			gpios = <&gpio2 23 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
 			wakeup-source;
 		};
 
-		f1 {
+		key-f1 {
 			label = "GPIO Key F1";
 			linux,code = <KEY_F1>;
 			gpios = <&gpio_pca 0 GPIO_ACTIVE_LOW>;
 		};
 
-		f2 {
+		key-f2 {
 			label = "GPIO Key F2";
 			linux,code = <KEY_F2>;
 			gpios = <&gpio_pca 1 GPIO_ACTIVE_LOW>;
 		};
 
-		f3 {
+		key-f3 {
 			label = "GPIO Key F3";
 			linux,code = <KEY_F3>;
 			gpios = <&gpio_pca 2 GPIO_ACTIVE_LOW>;
 		};
 
-		f4 {
+		key-f4 {
 			label = "GPIO Key F4";
 			linux,code = <KEY_F4>;
 			gpios = <&gpio_pca 3 GPIO_ACTIVE_LOW>;
 		};
 
-		f5 {
+		key-f5 {
 			label = "GPIO Key F5";
 			linux,code = <KEY_F5>;
 			gpios = <&gpio_pca 4 GPIO_ACTIVE_LOW>;
 		};
 
-		cycle {
+		key-cycle {
 			label = "GPIO Key CYCLE";
 			linux,code = <KEY_CYCLEWINDOWS>;
 			gpios = <&gpio_pca 5 GPIO_ACTIVE_LOW>;
 		};
 
-		esc {
+		key-esc {
 			label = "GPIO Key ESC";
 			linux,code = <KEY_ESC>;
 			gpios = <&gpio_pca 6 GPIO_ACTIVE_LOW>;
 		};
 
-		up {
+		key-up {
 			label = "GPIO Key UP";
 			linux,code = <KEY_UP>;
 			gpios = <&gpio_pca 7 GPIO_ACTIVE_LOW>;
 		};
 
-		down {
+		key-down {
 			label = "GPIO Key DOWN";
 			linux,code = <KEY_DOWN>;
 			gpios = <&gpio_pca 8 GPIO_ACTIVE_LOW>;
 		};
 
-		ok {
+		key-ok {
 			label = "GPIO Key OK";
 			linux,code = <KEY_OK>;
 			gpios = <&gpio_pca 9 GPIO_ACTIVE_LOW>;
 		};
 
-		f6 {
+		key-f6 {
 			label = "GPIO Key F6";
 			linux,code = <KEY_F6>;
 			gpios = <&gpio_pca 10 GPIO_ACTIVE_LOW>;
 		};
 
-		f7 {
+		key-f7 {
 			label = "GPIO Key F7";
 			linux,code = <KEY_F7>;
 			gpios = <&gpio_pca 11 GPIO_ACTIVE_LOW>;
 		};
 
-		f8 {
+		key-f8 {
 			label = "GPIO Key F8";
 			linux,code = <KEY_F8>;
 			gpios = <&gpio_pca 12 GPIO_ACTIVE_LOW>;
 		};
 
-		f9 {
+		key-f9 {
 			label = "GPIO Key F9";
 			linux,code = <KEY_F9>;
 			gpios = <&gpio_pca 13 GPIO_ACTIVE_LOW>;
 		};
 
-		f10 {
+		key-f10 {
 			label = "GPIO Key F10";
 			linux,code = <KEY_F10>;
 			gpios = <&gpio_pca 14 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/imx6dl-prtvt7.dts b/arch/arm/boot/dts/imx6dl-prtvt7.dts
index 190d26642bc8..a1eb53851794 100644
--- a/arch/arm/boot/dts/imx6dl-prtvt7.dts
+++ b/arch/arm/boot/dts/imx6dl-prtvt7.dts
@@ -6,6 +6,7 @@
 /dts-v1/;
 #include "imx6dl.dtsi"
 #include "imx6qdl-prti6q.dtsi"
+#include <dt-bindings/display/sdtv-standards.h>
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/leds/common.h>
 #include <dt-bindings/sound/fsl-imx-audmux.h>
@@ -28,95 +29,124 @@
 		power-supply = <&reg_bl_12v0>;
 	};
 
+	display {
+		compatible = "fsl,imx-parallel-display";
+		pinctrl-0 = <&pinctrl_ipu1_disp>;
+		pinctrl-names = "default";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+
+			display_in: endpoint {
+				remote-endpoint = <&ipu1_di0_disp0>;
+			};
+		};
+
+		port@1 {
+			reg = <1>;
+
+			display_out: endpoint {
+				remote-endpoint = <&panel_in>;
+			};
+		};
+	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&vdiv_vaccu>;
+	};
+
 	keys {
 		compatible = "gpio-keys";
 		autorepeat;
 
-		esc {
+		key-esc {
 			label = "GPIO Key ESC";
 			linux,code = <KEY_ESC>;
 			gpios = <&gpio_pca 0 GPIO_ACTIVE_LOW>;
 		};
 
-		up {
+		key-up {
 			label = "GPIO Key UP";
 			linux,code = <KEY_UP>;
 			gpios = <&gpio_pca 1 GPIO_ACTIVE_LOW>;
 		};
 
-		down {
+		key-down {
 			label = "GPIO Key DOWN";
 			linux,code = <KEY_DOWN>;
 			gpios = <&gpio_pca 4 GPIO_ACTIVE_LOW>;
 		};
 
-		enter {
+		key-enter {
 			label = "GPIO Key Enter";
 			linux,code = <KEY_ENTER>;
 			gpios = <&gpio_pca 3 GPIO_ACTIVE_LOW>;
 		};
 
-		cycle {
+		key-cycle {
 			label = "GPIO Key CYCLE";
 			linux,code = <KEY_CYCLEWINDOWS>;
 			gpios = <&gpio_pca 2 GPIO_ACTIVE_LOW>;
 		};
 
-		f1 {
+		key-f1 {
 			label = "GPIO Key F1";
 			linux,code = <KEY_F1>;
 			gpios = <&gpio_pca 14 GPIO_ACTIVE_LOW>;
 		};
 
-		f2 {
+		key-f2 {
 			label = "GPIO Key F2";
 			linux,code = <KEY_F2>;
 			gpios = <&gpio_pca 13 GPIO_ACTIVE_LOW>;
 		};
 
-		f3 {
+		key-f3 {
 			label = "GPIO Key F3";
 			linux,code = <KEY_F3>;
 			gpios = <&gpio_pca 12 GPIO_ACTIVE_LOW>;
 		};
 
-		f4 {
+		key-f4 {
 			label = "GPIO Key F4";
 			linux,code = <KEY_F4>;
 			gpios = <&gpio_pca 11 GPIO_ACTIVE_LOW>;
 		};
 
-		f5 {
+		key-f5 {
 			label = "GPIO Key F5";
 			linux,code = <KEY_F5>;
 			gpios = <&gpio_pca 10 GPIO_ACTIVE_LOW>;
 		};
 
-		f6 {
+		key-f6 {
 			label = "GPIO Key F6";
 			linux,code = <KEY_F6>;
 			gpios = <&gpio_pca 5 GPIO_ACTIVE_LOW>;
 		};
 
-		f7 {
+		key-f7 {
 			label = "GPIO Key F7";
 			linux,code = <KEY_F7>;
 			gpios = <&gpio_pca 6 GPIO_ACTIVE_LOW>;
 		};
 
-		f8 {
+		key-f8 {
 			label = "GPIO Key F8";
 			linux,code = <KEY_F8>;
 			gpios = <&gpio_pca 7 GPIO_ACTIVE_LOW>;
 		};
 
-		f9 {
+		key-f9 {
 			label = "GPIO Key F9";
 			linux,code = <KEY_F9>;
 			gpios = <&gpio_pca 8 GPIO_ACTIVE_LOW>;
 		};
 
-		f10 {
+		key-f10 {
 			label = "GPIO Key F10";
 			linux,code = <KEY_F10>;
 			gpios = <&gpio_pca 9 GPIO_ACTIVE_LOW>;
@@ -135,6 +165,30 @@
 		};
 	};
 
+	panel {
+		compatible = "innolux,g070y2-t02";
+		backlight = <&backlight_lcd>;
+		power-supply = <&reg_3v3>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&display_out>;
+			};
+		};
+	};
+
+	connector {
+		compatible = "composite-video-connector";
+		label = "Composite0";
+		sdtv-standards = <SDTV_STD_PAL_B>;
+
+		port {
+			comp0_out: endpoint {
+				remote-endpoint = <&tvp5150_comp0_in>;
+			};
+		};
+	};
+
 	reg_bl_12v0: regulator-bl-12v0 {
 		compatible = "regulator-fixed";
 		pinctrl-names = "default";
@@ -146,6 +200,13 @@
 		enable-active-high;
 	};
 
+	reg_3v3: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
 	reg_1v8: regulator-1v8 {
 		compatible = "regulator-fixed";
 		regulator-name = "1v8";
@@ -179,6 +240,64 @@
 			frame-master;
 		};
 	};
+
+	thermal-zones {
+		chassis-thermal {
+			polling-delay = <20000>;
+			polling-delay-passive = <0>;
+			thermal-sensors = <&tsens0>;
+		};
+
+		touch-thermal0 {
+			polling-delay = <20000>;
+			polling-delay-passive = <0>;
+			thermal-sensors = <&touch_temp0>;
+		};
+
+		touch-thermal1 {
+			polling-delay = <20000>;
+			polling-delay-passive = <0>;
+			thermal-sensors = <&touch_temp1>;
+		};
+	};
+
+	touchscreen {
+		compatible = "resistive-adc-touch";
+		io-channels = <&adc_ts 1>, <&adc_ts 3>, <&adc_ts 4>,
+                              <&adc_ts 5>;
+		io-channel-names = "y", "z1", "z2", "x";
+		touchscreen-min-pressure = <64687>;
+		touchscreen-inverted-x;
+		touchscreen-inverted-y;
+		touchscreen-x-plate-ohms = <300>;
+		touchscreen-y-plate-ohms = <800>;
+	};
+
+	touch_temp0: touch-temperature-sensor0 {
+		compatible = "generic-adc-thermal";
+		#thermal-sensor-cells = <0>;
+		io-channels = <&adc_ts 0>;
+		io-channel-names = "sensor-channel";
+		temperature-lookup-table = <    (-40000) 736
+						85000 474>;
+	};
+
+	touch_temp1: touch-temperature-sensor1 {
+		compatible = "generic-adc-thermal";
+		#thermal-sensor-cells = <0>;
+		io-channels = <&adc_ts 7>;
+		io-channel-names = "sensor-channel";
+		temperature-lookup-table = <    (-40000) 826
+						85000 609>;
+	};
+
+	vdiv_vaccu: voltage-divider-vaccu {
+		compatible = "voltage-divider";
+		io-channels = <&adc_ts 2>;
+		output-ohms = <2500>;
+		full-ohms = <64000>;
+		#io-channel-cells = <0>;
+	};
 };
 
 &audmux {
@@ -221,22 +340,41 @@
 	pinctrl-0 = <&pinctrl_ecspi2>;
 	status = "okay";
 
-	touchscreen@0 {
-		compatible = "ti,tsc2046";
+	adc_ts: adc@0 {
+		compatible = "ti,tsc2046e-adc";
 		reg = <0>;
 		pinctrl-0 = <&pinctrl_tsc>;
-		pinctrl-names ="default";
-		spi-max-frequency = <100000>;
-		interrupts-extended = <&gpio3 20 IRQ_TYPE_EDGE_FALLING>;
-		pendown-gpio = <&gpio3 20 GPIO_ACTIVE_LOW>;
-		touchscreen-max-pressure = <4095>;
-		ti,vref-delay-usecs = /bits/ 16 <100>;
-		ti,x-plate-ohms = /bits/ 16 <800>;
-		ti,y-plate-ohms = /bits/ 16 <300>;
-		ti,debounce-max = /bits/ 16 <3>;
-		ti,debounce-tol = /bits/ 16 <70>;
-		ti,debounce-rep = /bits/ 16 <3>;
-		wakeup-source;
+		pinctrl-names = "default";
+		spi-max-frequency = <1000000>;
+		interrupts-extended = <&gpio3 20 IRQ_TYPE_LEVEL_LOW>;
+		#io-channel-cells = <1>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		channel@1 {
+			reg = <1>;
+			settling-time-us = <700>;
+			oversampling-ratio = <5>;
+		};
+
+		channel@3 {
+			reg = <3>;
+			settling-time-us = <700>;
+			oversampling-ratio = <5>;
+		};
+
+		channel@4 {
+			reg = <4>;
+			settling-time-us = <700>;
+			oversampling-ratio = <5>;
+		};
+
+		channel@5 {
+			reg = <5>;
+			settling-time-us = <700>;
+			oversampling-ratio = <5>;
+		};
 	};
 };
 
@@ -252,6 +390,31 @@
 		VDDIO-supply = <&reg_3v3>;
 		VDDD-supply = <&reg_1v8>;
 	};
+
+	video@5c {
+		compatible = "ti,tvp5150";
+		reg = <0x5c>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+
+			tvp5150_comp0_in: endpoint {
+				remote-endpoint = <&comp0_out>;
+			};
+		};
+
+		/* Output port 2 is video output pad */
+		port@2 {
+			reg = <2>;
+
+			tvp5151_to_ipu1_csi0_mux: endpoint {
+				remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>;
+			};
+		};
+	};
 };
 
 &i2c3 {
@@ -260,6 +423,12 @@
 		reg = <0x51>;
 	};
 
+	tsens0: temperature-sensor@70 {
+		compatible = "ti,tmp103";
+		reg = <0x70>;
+		#thermal-sensor-cells = <0>;
+	};
+
 	gpio_pca: gpio@74 {
 		compatible = "nxp,pca9539";
 		reg = <0x74>;
@@ -275,6 +444,14 @@
 	status = "okay";
 };
 
+&ipu1_di0_disp0 {
+	remote-endpoint = <&display_in>;
+};
+
+&ipu1_csi0_mux_from_parallel_sensor {
+	remote-endpoint = <&tvp5151_to_ipu1_csi0_mux>;
+};
+
 &pwm1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm1>;
diff --git a/arch/arm/boot/dts/imx6dl-rex-basic.dts b/arch/arm/boot/dts/imx6dl-rex-basic.dts
index 0f1616bfa9a8..b72f8ea1e6f6 100644
--- a/arch/arm/boot/dts/imx6dl-rex-basic.dts
+++ b/arch/arm/boot/dts/imx6dl-rex-basic.dts
@@ -19,7 +19,7 @@
 };
 
 &ecspi3 {
-	flash: m25p80@0 {
+	flash: flash@0 {
 		compatible = "sst,sst25vf016b", "jedec,spi-nor";
 		spi-max-frequency = <20000000>;
 		reg = <0>;
diff --git a/arch/arm/boot/dts/imx6dl-riotboard.dts b/arch/arm/boot/dts/imx6dl-riotboard.dts
index e7d9bfbfd0e4..e7be05f205d3 100644
--- a/arch/arm/boot/dts/imx6dl-riotboard.dts
+++ b/arch/arm/boot/dts/imx6dl-riotboard.dts
@@ -90,6 +90,7 @@
 	pinctrl-0 = <&pinctrl_enet>;
 	phy-mode = "rgmii-id";
 	phy-handle = <&rgmii_phy>;
+	/delete-property/ interrupts;
 	interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
 			      <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
 	fsl,err006687-workaround-present;
diff --git a/arch/arm/boot/dts/imx6dl-victgo.dts b/arch/arm/boot/dts/imx6dl-victgo.dts
index d37ba4ed847d..72df1dba83be 100644
--- a/arch/arm/boot/dts/imx6dl-victgo.dts
+++ b/arch/arm/boot/dts/imx6dl-victgo.dts
@@ -5,60 +5,27 @@
  */
 
 /dts-v1/;
-#include <dt-bindings/display/sdtv-standards.h>
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/leds/common.h>
-#include <dt-bindings/media/tvp5150.h>
-#include <dt-bindings/sound/fsl-imx-audmux.h>
 #include "imx6dl.dtsi"
+#include "imx6qdl-vicut1.dtsi"
 
 / {
 	model = "Kverneland TGO";
 	compatible = "kvg,victgo", "fsl,imx6dl";
 
-	chosen {
-		stdout-path = &uart4;
-	};
-
-	backlight: backlight {
-		compatible = "pwm-backlight";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_backlight>;
-		pwms = <&pwm1 0 5000000 0>;
-		brightness-levels = <0 16 64 255>;
-		num-interpolated-steps = <16>;
-		default-brightness-level = <1>;
-		power-supply = <&reg_3v3>;
-		enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
-	};
-
-	connector {
-		compatible = "composite-video-connector";
-		label = "Composite0";
-		sdtv-standards = <SDTV_STD_PAL_B>;
-
-		port {
-			comp0_out: endpoint {
-				remote-endpoint = <&tvp5150_comp0_in>;
-			};
-		};
-	};
-
 	gpio-keys {
 		compatible = "gpio-keys";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gpiokeys>;
 		autorepeat;
 
-		power {
+		key-power {
 			label = "Power Button";
 			gpios = <&gpio2 23 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
 			wakeup-source;
 		};
 
-		enter {
+		key-enter {
 			label = "Rotary Key";
 			gpios = <&gpio2 05 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_ENTER>;
@@ -66,36 +33,14 @@
 		};
 	};
 
-	leds {
-		compatible = "gpio-leds";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_leds>;
-
-		led-0 {
-			label = "debug0";
-			function = LED_FUNCTION_HEARTBEAT;
-			gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "heartbeat";
-		};
-
-		led-1 {
-			label = "debug1";
-			function = LED_FUNCTION_DISK;
-			gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
-			linux,default-trigger = "disk-activity";
-		};
-
-		led-2 {
-			label = "power_led";
-			function = LED_FUNCTION_POWER;
-			gpios = <&gpio2 24 GPIO_ACTIVE_HIGH>;
-			default-state = "on";
-		};
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&vdiv_vaccu>, <&vdiv_hitch_pos>;
 	};
 
 	panel {
-		compatible = "kyo,tcg121xglp";
-		backlight = <&backlight>;
+		compatible = "lg,lb070wv8";
+		backlight = <&backlight_lcd>;
 		power-supply = <&reg_3v3>;
 
 		port {
@@ -111,38 +56,6 @@
 		clock-frequency = <50000000>;
 	};
 
-	reg_1v8: regulator-1v8 {
-		compatible = "regulator-fixed";
-		regulator-name = "1v8";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <1800000>;
-	};
-
-	reg_3v3: regulator-3v3 {
-		compatible = "regulator-fixed";
-		regulator-name = "3v3";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-	};
-
-	reg_h1_vbus: regulator-h1-vbus {
-		compatible = "regulator-fixed";
-		regulator-name = "h1-vbus";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-		gpio = <&gpio1 0 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-	};
-
-	reg_otg_vbus: regulator-otg-vbus {
-		compatible = "regulator-fixed";
-		regulator-name = "otg-vbus";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-		gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-	};
-
 	rotary-encoder {
 		compatible = "rotary-encoder";
 		pinctrl-0 = <&pinctrl_rotary_ch>;
@@ -155,86 +68,69 @@
 		wakeup-source;
 	};
 
-	sound {
-		compatible = "simple-audio-card";
-		simple-audio-card,name = "prti6q-sgtl5000";
-		simple-audio-card,format = "i2s";
-		simple-audio-card,widgets =
-			"Microphone", "Microphone Jack",
-			"Line", "Line In Jack",
-			"Headphone", "Headphone Jack",
-			"Speaker", "External Speaker";
-		simple-audio-card,routing =
-			"MIC_IN", "Microphone Jack",
-			"LINE_IN", "Line In Jack",
-			"Headphone Jack", "HP_OUT",
-			"External Speaker", "LINE_OUT";
-
-		simple-audio-card,cpu {
-			sound-dai = <&ssi1>;
-			system-clock-frequency = <0>;
+	thermal-zones {
+		chassis-thermal {
+			polling-delay = <20000>;
+			polling-delay-passive = <0>;
+			thermal-sensors = <&tsens0>;
 		};
 
-		simple-audio-card,codec {
-			sound-dai = <&codec>;
-			bitclock-master;
-			frame-master;
+		touch-thermal0 {
+			polling-delay = <20000>;
+			polling-delay-passive = <0>;
+			thermal-sensors = <&touch_temp0>;
 		};
-	};
-};
-
-&audmux {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_audmux>;
-	status = "okay";
 
-	mux-ssi1 {
-		fsl,audmux-port = <0>;
-		fsl,port-config = <
-			IMX_AUDMUX_V2_PTCR_SYN		0
-			IMX_AUDMUX_V2_PTCR_TFSEL(2)	0
-			IMX_AUDMUX_V2_PTCR_TCSEL(2)	0
-			IMX_AUDMUX_V2_PTCR_TFSDIR	0
-			IMX_AUDMUX_V2_PTCR_TCLKDIR	IMX_AUDMUX_V2_PDCR_RXDSEL(2)
-		>;
+		touch-thermal1 {
+			polling-delay = <20000>;
+			polling-delay-passive = <0>;
+			thermal-sensors = <&touch_temp1>;
+		};
 	};
 
-	mux-pins3 {
-		fsl,audmux-port = <2>;
-		fsl,port-config = <
-			IMX_AUDMUX_V2_PTCR_SYN		IMX_AUDMUX_V2_PDCR_RXDSEL(0)
-			0				IMX_AUDMUX_V2_PDCR_TXRXEN
-		>;
+	touchscreen {
+		compatible = "resistive-adc-touch";
+		io-channels = <&adc_ts 1>, <&adc_ts 3>, <&adc_ts 4>,
+                              <&adc_ts 5>;
+		io-channel-names = "y", "z1", "z2", "x";
+		touchscreen-min-pressure = <64687>;
+		touchscreen-inverted-y;
+		touchscreen-x-plate-ohms = <300>;
+		touchscreen-y-plate-ohms = <800>;
 	};
-};
 
-&can1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_can1>;
-	status = "okay";
-};
-
-&can2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_can2>;
-	status = "okay";
-};
+	touch_temp0: touch-temperature-sensor0 {
+		compatible = "generic-adc-thermal";
+		#thermal-sensor-cells = <0>;
+		io-channels = <&adc_ts 0>;
+		io-channel-names = "sensor-channel";
+		temperature-lookup-table = <    (-40000) 736
+						85000 474>;
+	};
 
-&clks {
-	assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>;
-	assigned-clock-parents = <&clks IMX6QDL_CLK_PLL5_VIDEO_DIV>;
-};
+	touch_temp1: touch-temperature-sensor1 {
+		compatible = "generic-adc-thermal";
+		#thermal-sensor-cells = <0>;
+		io-channels = <&adc_ts 7>;
+		io-channel-names = "sensor-channel";
+		temperature-lookup-table = <    (-40000) 826
+						85000 609>;
+	};
 
-&ecspi1 {
-	cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_ecspi1>;
-	status = "okay";
+	vdiv_vaccu: voltage-divider-vaccu {
+		compatible = "voltage-divider";
+		io-channels = <&adc_ts 2>;
+		output-ohms = <2500>;
+		full-ohms = <64000>;
+		#io-channel-cells = <0>;
+	};
 
-	flash@0 {
-		compatible = "jedec,spi-nor";
-		reg = <0>;
-		spi-max-frequency = <20000000>;
+	vdiv_hitch_pos: voltage-divider-hitch-pos {
+		compatible = "voltage-divider";
+		io-channels = <&adc_ts 6>;
+		output-ohms = <3300>;
+		full-ohms = <13300>;
+		#io-channel-cells = <0>;
 	};
 };
 
@@ -244,22 +140,41 @@
 	pinctrl-0 = <&pinctrl_ecspi2>;
 	status = "okay";
 
-	touchscreen@0 {
-		compatible = "ti,tsc2046";
+	adc_ts: adc@0 {
+		compatible = "ti,tsc2046e-adc";
 		reg = <0>;
-		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_touchscreen>;
-		spi-max-frequency = <200000>;
-		interrupts-extended = <&gpio5 8 IRQ_TYPE_EDGE_FALLING>;
-		pendown-gpio = <&gpio5 8 GPIO_ACTIVE_LOW>;
-		touchscreen-size-x = <800>;
-		touchscreen-size-y = <480>;
-		touchscreen-inverted-y;
-		touchscreen-max-pressure = <4095>;
-		ti,vref-delay-usecs = /bits/ 16 <100>;
-		ti,x-plate-ohms = /bits/ 16 <800>;
-		ti,y-plate-ohms = /bits/ 16 <300>;
-		wakeup-source;
+		pinctrl-names = "default";
+		spi-max-frequency = <1000000>;
+		interrupts-extended = <&gpio5 8 IRQ_TYPE_LEVEL_LOW>;
+		#io-channel-cells = <1>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		channel@1 {
+			reg = <1>;
+			settling-time-us = <700>;
+			oversampling-ratio = <5>;
+		};
+
+		channel@3 {
+			reg = <3>;
+			settling-time-us = <700>;
+			oversampling-ratio = <5>;
+		};
+
+		channel@4 {
+			reg = <4>;
+			settling-time-us = <700>;
+			oversampling-ratio = <5>;
+		};
+
+		channel@5 {
+			reg = <5>;
+			settling-time-us = <700>;
+			oversampling-ratio = <5>;
+		};
 	};
 };
 
@@ -295,36 +210,19 @@
 			"CAM2_MIRROR", "", "", "SMBALERT",
 		"DEBUG_0", "DEBUG_1", "", "", "", "", "", "",
 		"SD1_DATA0", "SD1_DATA1", "SD1_CMD", "SD1_DATA2", "SD1_CLK",
-			"SD1_DATA3", "", "",
-		"", "", "", "", "", "", "", "";
-};
-
-&gpio2 {
-	gpio-line-names =
-		"", "", "", "", "", "", "", "",
-		"REV_ID0", "REV_ID1", "REV_ID2", "REV_ID3", "REV_ID4",
-			"BOARD_ID0", "BOARD_ID1", "BOARD_ID2",
-		"", "", "", "", "", "", "ISB_IN1", "ON_SWITCH",
-		"POWER_LED", "", "", "", "", "", "", "";
-};
-
-&gpio3 {
-	gpio-line-names =
-		"", "", "", "", "", "", "", "",
-		"", "", "", "", "", "", "", "",
-		"ECSPI1_SCLK", "ECSPI1_MISO", "ECSPI1_MOSI", "ECSPI1_SS1",
-			"CPU_ON1_FB", "USB_EXT1_OC", "USB_EXT1_PWR", "YACO_IRQ",
-		"TSS_TXD", "TSS_RXD", "", "", "", "", "YACO_BOOT0",
-			"YACO_RESET";
+			"SD1_DATA3", "ETH_MDIO", "",
+		"", "", "", "", "", "", "", "ETH_MDC";
 };
 
 &gpio4 {
 	gpio-line-names =
-		"", "", "", "", "", "", "", "",
-		"", "", "", "", "CAN1_SR", "CAN2_SR", "CAN2_TX", "CAN2_RX",
-		"", "", "DIP1_FB", "", "VCAM_EN", "", "", "",
-		"CPU_LIGHT_ON", "", "ETH_RESET", "CPU_CONTACT_IN", "BL_EN",
-			"BL_PWM", "ETH_INTRP", "ISB_LED";
+		"", "", "", "", "", "", "UART4_TXD", "UART4_RXD",
+		"UART5_TXD", "UART5_RXD", "CAN1_TX", "CAN1_RX", "CAN1_SR",
+			"CAN2_SR", "CAN2_TX", "CAN2_RX",
+		"", "", "DIP1_FB", "", "VCAM_EN", "ON1_CTRL", "ON2_CTRL",
+			"HITCH_IN_OUT",
+		"LIGHT_ON", "", "ETH_RESET", "CONTACT_IN", "BL_EN",
+			"BL_PWM", "ETH_INT", "ISB_LED";
 };
 
 &gpio5 {
@@ -332,51 +230,22 @@
 		"", "", "", "", "", "", "", "",
 		"TSC_PENIRQ", "TSC_BUSY", "ECSPI2_MOSI", "ECSPI2_MISO",
 			"ECSPI2_SS0", "ECSPI2_SCLK", "", "",
-		"", "", "", "", "", "", "", "",
+		"", "", "ITU656_CLK", "I2S_MCLK", "ITU656_PDN", "AUDIO_RESET",
+			"I2S_BITCLK", "I2S_DOUT",
 		"I2S_LRCLK", "I2S_DIN", "I2C1_SDA", "I2C1_SCL", "YACO_AUX_RX",
 			"YACO_AUX_TX", "ITU656_D0", "ITU656_D1";
 };
 
-&i2c1 {
-	clock-frequency = <100000>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_i2c1>;
-	status = "okay";
-
-	codec: audio-codec@a {
-		compatible = "fsl,sgtl5000";
-		reg = <0xa>;
-		#sound-dai-cells = <0>;
-		clocks = <&clks 201>;
-		VDDA-supply = <&reg_3v3>;
-		VDDIO-supply = <&reg_3v3>;
-		VDDD-supply = <&reg_1v8>;
-	};
-
-	video-decoder@5c {
-		compatible = "ti,tvp5150";
-		reg = <0x5c>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		port@0 {
-			reg = <0>;
-
-			tvp5150_comp0_in: endpoint {
-				remote-endpoint = <&comp0_out>;
-			};
-		};
-
-		/* Output port 2 is video output pad */
-		port@2 {
-			reg = <2>;
-
-			tvp5151_to_ipu1_csi0_mux: endpoint {
-				remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>;
-			};
-		};
-	};
+&gpio6 {
+	gpio-line-names =
+		"ITU656_D2", "ITU656_D3", "ITU656_D4", "ITU656_D5",
+			"ITU656_D6", "ITU656_D7", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "";
+};
 
+&i2c1 {
 	keypad@70 {
 		compatible = "holtek,ht16k33";
 		pinctrl-names = "default";
@@ -400,224 +269,9 @@
 			MATRIX_KEY(6, 1, KEY_F1)
 		      >;
 	};
-
-	/* additional i2c devices are added automatically by the boot loader */
-};
-
-&i2c3 {
-	clock-frequency = <100000>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_i2c3>;
-	status = "okay";
-
-	adc@49 {
-		compatible = "ti,ads1015";
-		reg = <0x49>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		channel@4 {
-			reg = <4>;
-			ti,gain = <3>;
-			ti,datarate = <3>;
-		};
-
-		channel@5 {
-			reg = <5>;
-			ti,gain = <3>;
-			ti,datarate = <3>;
-		};
-
-		channel@6 {
-			reg = <6>;
-			ti,gain = <3>;
-			ti,datarate = <3>;
-		};
-
-		channel@7 {
-			reg = <7>;
-			ti,gain = <3>;
-			ti,datarate = <3>;
-		};
-	};
-
-	rtc@51 {
-		compatible = "nxp,pcf8563";
-		reg = <0x51>;
-	};
-
-	temperature-sensor@70 {
-		compatible = "ti,tmp103";
-		reg = <0x70>;
-	};
-};
-
-&ipu1_csi0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_ipu1_csi0>;
-	status = "okay";
-};
-
-&ipu1_csi0_mux_from_parallel_sensor {
-	remote-endpoint = <&tvp5151_to_ipu1_csi0_mux>;
-};
-
-&ldb {
-	status = "okay";
-
-	lvds-channel@0 {
-		status = "okay";
-
-		port@4 {
-			reg = <4>;
-
-			lvds0_out: endpoint {
-				remote-endpoint = <&panel_in>;
-			};
-		};
-	};
-};
-
-&pwm1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_pwm1>;
-	status = "okay";
-};
-
-&pwm3 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_pwm3>;
-	status = "okay";
-};
-
-&ssi1 {
-	#sound-dai-cells = <0>;
-	fsl,mode = "ac97-slave";
-	status = "okay";
-};
-
-&uart1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart1>;
-	status = "okay";
-};
-
-&uart2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart2>;
-	status = "okay";
-};
-
-&uart3 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart3>;
-	status = "okay";
-};
-
-&uart4 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart4>;
-	status = "okay";
-};
-
-&uart5 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart5>;
-	status = "okay";
-};
-
-&usbh1 {
-	vbus-supply = <&reg_h1_vbus>;
-	pinctrl-names = "default";
-	phy_type = "utmi";
-	dr_mode = "host";
-	status = "okay";
-};
-
-&usbotg {
-	vbus-supply = <&reg_otg_vbus>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usbotg>;
-	phy_type = "utmi";
-	dr_mode = "host";
-	disable-over-current;
-	status = "okay";
-};
-
-&usdhc1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc1>;
-	cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
-	no-1-8-v;
-	disable-wp;
-	cap-sd-highspeed;
-	no-mmc;
-	no-sdio;
-	status = "okay";
-};
-
-&usdhc3 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc3>;
-	bus-width = <8>;
-	no-1-8-v;
-	non-removable;
-	no-sd;
-	no-sdio;
-	status = "okay";
 };
 
 &iomuxc {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_hog>;
-
-	pinctrl_audmux: audmuxgrp {
-		fsl,pins = <
-			/* SGTL5000 sys_mclk */
-			MX6QDL_PAD_CSI0_MCLK__CCM_CLKO1			0x030b0
-			MX6QDL_PAD_CSI0_DAT7__AUD3_RXD			0x130b0
-			MX6QDL_PAD_CSI0_DAT4__AUD3_TXC			0x130b0
-			MX6QDL_PAD_CSI0_DAT5__AUD3_TXD			0x110b0
-			MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS			0x130b0
-		>;
-	};
-
-	pinctrl_backlight: backlightgrp {
-		fsl,pins = <
-			MX6QDL_PAD_DISP0_DAT7__GPIO4_IO28		0x1b0b0
-		>;
-	};
-
-	pinctrl_can1: can1grp {
-		fsl,pins = <
-			MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX		0x1b000
-			MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX		0x3008
-			/* CAN1_SR */
-			MX6QDL_PAD_KEY_COL3__GPIO4_IO12			0x13008
-			/* CAN1_TERM */
-			MX6QDL_PAD_GPIO_0__GPIO1_IO00			0x1b088
-		>;
-	};
-
-	pinctrl_can2: can2grp {
-		fsl,pins = <
-			MX6QDL_PAD_KEY_ROW4__FLEXCAN2_RX		0x1b000
-			MX6QDL_PAD_KEY_COL4__FLEXCAN2_TX		0x3008
-			/* CAN2_SR */
-			MX6QDL_PAD_KEY_ROW3__GPIO4_IO13			0x13008
-		>;
-	};
-
-	pinctrl_ecspi1: ecspi1grp {
-		fsl,pins = <
-			MX6QDL_PAD_EIM_D17__ECSPI1_MISO			0x100b1
-			MX6QDL_PAD_EIM_D18__ECSPI1_MOSI			0x100b1
-			MX6QDL_PAD_EIM_D16__ECSPI1_SCLK			0x100b1
-			/* CS */
-			MX6QDL_PAD_EIM_D19__GPIO3_IO19			0x000b1
-		>;
-	};
-
 	pinctrl_ecspi2: ecspi2grp {
 		fsl,pins = <
 			MX6QDL_PAD_DISP0_DAT16__ECSPI2_MOSI		0x100b1
@@ -656,113 +310,12 @@
 		>;
 	};
 
-	pinctrl_hog: hoggrp {
-		fsl,pins = <
-			/* ITU656_nRESET */
-			MX6QDL_PAD_GPIO_2__GPIO1_IO02			0x1b0b0
-			/* CAM1_MIRROR */
-			MX6QDL_PAD_GPIO_3__GPIO1_IO03			0x130b0
-			/* CAM2_MIRROR */
-			MX6QDL_PAD_GPIO_4__GPIO1_IO04			0x130b0
-			/* CAM_nDETECT */
-			MX6QDL_PAD_GPIO_17__GPIO7_IO12			0x1b0b0
-			/* ISB_IN1 */
-			MX6QDL_PAD_EIM_A16__GPIO2_IO22			0x130b0
-			/* ISB_nIN2 */
-			MX6QDL_PAD_EIM_A17__GPIO2_IO21			0x1b0b0
-			/* WARN_LIGHT */
-			MX6QDL_PAD_EIM_A19__GPIO2_IO19			0x100b0
-			/* ON2_FB */
-			MX6QDL_PAD_EIM_A25__GPIO5_IO02			0x100b0
-			/* YACO_nIRQ */
-			MX6QDL_PAD_EIM_D23__GPIO3_IO23			0x1b0b0
-			/* YACO_BOOT0 */
-			MX6QDL_PAD_EIM_D30__GPIO3_IO30			0x130b0
-			/* YACO_nRESET */
-			MX6QDL_PAD_EIM_D31__GPIO3_IO31			0x1b0b0
-			/* FORCE_ON1 */
-			MX6QDL_PAD_EIM_EB2__GPIO2_IO30			0x1b0b0
-			/* AUDIO_nRESET */
-			MX6QDL_PAD_CSI0_VSYNC__GPIO5_IO21		0x1f0b0
-			/* ITU656_nPDN */
-			MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20		0x1b0b0
-
-			/* HW revision detect */
-			/* REV_ID0 */
-			MX6QDL_PAD_SD4_DAT0__GPIO2_IO08			0x1b0b0
-			/* REV_ID1 is shared with PWM3 */
-			/* REV_ID2 */
-			MX6QDL_PAD_SD4_DAT2__GPIO2_IO10			0x1b0b0
-			/* REV_ID3 */
-			MX6QDL_PAD_SD4_DAT3__GPIO2_IO11			0x1b0b0
-			/* REV_ID4 */
-			MX6QDL_PAD_SD4_DAT4__GPIO2_IO12			0x1b0b0
-
-			/* New in HW revision 1 */
-			/* ON1_FB */
-			MX6QDL_PAD_EIM_D20__GPIO3_IO20			0x100b0
-			/* DIP1_FB */
-			MX6QDL_PAD_DI0_PIN2__GPIO4_IO18			0x1b0b0
-		>;
-	};
-
-	pinctrl_i2c1: i2c1grp {
-		fsl,pins = <
-			MX6QDL_PAD_CSI0_DAT8__I2C1_SDA		0x4001f8b1
-			MX6QDL_PAD_CSI0_DAT9__I2C1_SCL		0x4001f8b1
-		>;
-	};
-
-	pinctrl_i2c3: i2c3grp {
-		fsl,pins = <
-			MX6QDL_PAD_GPIO_5__I2C3_SCL		0x4001b8b1
-			MX6QDL_PAD_GPIO_6__I2C3_SDA		0x4001b8b1
-		>;
-	};
-
-	pinctrl_ipu1_csi0: ipu1csi0grp {
-		fsl,pins = <
-			MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12		0x1b0b0
-			MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13		0x1b0b0
-			MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14		0x1b0b0
-			MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15		0x1b0b0
-			MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16		0x1b0b0
-			MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17		0x1b0b0
-			MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18		0x1b0b0
-			MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19		0x1b0b0
-			MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK	0x1b0b0
-		>;
-	};
-
 	pinctrl_keypad: keypadgrp {
 		fsl,pins = <
 			MX6QDL_PAD_GPIO_19__GPIO4_IO05			0x1b0b0
 		>;
 	};
 
-	pinctrl_leds: ledsgrp {
-		fsl,pins = <
-			/* DEBUG0 */
-			MX6QDL_PAD_DI0_DISP_CLK__GPIO4_IO16		0x1b0b0
-			/* DEBUG1 */
-			MX6QDL_PAD_DI0_PIN15__GPIO4_IO17		0x1b0b0
-			/* POWER_LED */
-			MX6QDL_PAD_EIM_CS1__GPIO2_IO24			0x1b0b0
-		>;
-	};
-
-	pinctrl_pwm1: pwm1grp {
-		fsl,pins = <
-			MX6QDL_PAD_DISP0_DAT8__PWM1_OUT			0x1b0b0
-		>;
-	};
-
-	pinctrl_pwm3: pwm3grp {
-		fsl,pins = <
-			MX6QDL_PAD_SD4_DAT1__PWM3_OUT			0x1b0b0
-		>;
-	};
-
 	pinctrl_rotary_ch: rotarychgrp {
 		fsl,pins = <
 			MX6QDL_PAD_NANDF_D3__GPIO2_IO03			0x1b0b0
@@ -776,77 +329,4 @@
 			MX6QDL_PAD_DISP0_DAT15__GPIO5_IO09		0x1b0b0
 		>;
 	};
-
-	/* YaCO AUX Uart */
-	pinctrl_uart1: uart1grp {
-		fsl,pins = <
-			MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA		0x1b0b1
-			MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA		0x1b0b1
-		>;
-	};
-
-	pinctrl_uart2: uart2grp {
-		fsl,pins = <
-			MX6QDL_PAD_EIM_D26__UART2_TX_DATA		0x1b0b1
-			MX6QDL_PAD_EIM_D27__UART2_RX_DATA		0x1b0b1
-		>;
-	};
-
-	/* YaCO Touchscreen UART */
-	pinctrl_uart3: uart3grp {
-		fsl,pins = <
-			MX6QDL_PAD_EIM_D24__UART3_TX_DATA		0x1b0b1
-			MX6QDL_PAD_EIM_D25__UART3_RX_DATA		0x1b0b1
-		>;
-	};
-
-	pinctrl_uart4: uart4grp {
-		fsl,pins = <
-			MX6QDL_PAD_KEY_COL0__UART4_TX_DATA		0x1b0b1
-			MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA		0x1b0b1
-		>;
-	};
-
-	pinctrl_uart5: uart5grp {
-		fsl,pins = <
-			MX6QDL_PAD_KEY_COL1__UART5_TX_DATA		0x1b0b1
-			MX6QDL_PAD_KEY_ROW1__UART5_RX_DATA		0x1b0b1
-		>;
-	};
-
-	pinctrl_usbotg: usbotggrp {
-		fsl,pins = <
-			MX6QDL_PAD_EIM_D21__USB_OTG_OC			0x1b0b0
-			/* power enable, high active */
-			MX6QDL_PAD_EIM_D22__GPIO3_IO22			0x1b0b0
-		>;
-	};
-
-	pinctrl_usdhc1: usdhc1grp {
-		fsl,pins = <
-			MX6QDL_PAD_SD1_CMD__SD1_CMD			0x170f9
-			MX6QDL_PAD_SD1_CLK__SD1_CLK			0x100f9
-			MX6QDL_PAD_SD1_DAT0__SD1_DATA0			0x170f9
-			MX6QDL_PAD_SD1_DAT1__SD1_DATA1			0x170f9
-			MX6QDL_PAD_SD1_DAT2__SD1_DATA2			0x170f9
-			MX6QDL_PAD_SD1_DAT3__SD1_DATA3			0x170f9
-			MX6QDL_PAD_GPIO_1__GPIO1_IO01			0x1b0b0
-		>;
-	};
-
-	pinctrl_usdhc3: usdhc3grp {
-		fsl,pins = <
-			MX6QDL_PAD_SD3_CMD__SD3_CMD			0x17099
-			MX6QDL_PAD_SD3_CLK__SD3_CLK			0x10099
-			MX6QDL_PAD_SD3_DAT0__SD3_DATA0			0x17099
-			MX6QDL_PAD_SD3_DAT1__SD3_DATA1			0x17099
-			MX6QDL_PAD_SD3_DAT2__SD3_DATA2			0x17099
-			MX6QDL_PAD_SD3_DAT3__SD3_DATA3			0x17099
-			MX6QDL_PAD_SD3_DAT4__SD3_DATA4			0x17099
-			MX6QDL_PAD_SD3_DAT5__SD3_DATA5			0x17099
-			MX6QDL_PAD_SD3_DAT6__SD3_DATA6			0x17099
-			MX6QDL_PAD_SD3_DAT7__SD3_DATA7			0x17099
-			MX6QDL_PAD_SD3_RST__SD3_RESET			0x1b0b1
-		>;
-	};
 };
diff --git a/arch/arm/boot/dts/imx6dl-vicut1.dts b/arch/arm/boot/dts/imx6dl-vicut1.dts
index 174fd913bf96..5035d303447d 100644
--- a/arch/arm/boot/dts/imx6dl-vicut1.dts
+++ b/arch/arm/boot/dts/imx6dl-vicut1.dts
@@ -6,6 +6,7 @@
 /dts-v1/;
 #include "imx6dl.dtsi"
 #include "imx6qdl-vicut1.dtsi"
+#include "imx6qdl-vicut1-12inch.dtsi"
 
 / {
 	model = "Kverneland UT1 Board";
diff --git a/arch/arm/boot/dts/imx6dl-yapp4-common.dtsi b/arch/arm/boot/dts/imx6dl-yapp4-common.dtsi
index 674af39c884a..52162e8c7274 100644
--- a/arch/arm/boot/dts/imx6dl-yapp4-common.dtsi
+++ b/arch/arm/boot/dts/imx6dl-yapp4-common.dtsi
@@ -55,6 +55,7 @@
 	panel: panel {
 		compatible = "dataimage,scf0700c48ggu18";
 		power-supply = <&sw2_reg>;
+		backlight = <&backlight>;
 		status = "disabled";
 
 		port {
diff --git a/arch/arm/boot/dts/imx6dl.dtsi b/arch/arm/boot/dts/imx6dl.dtsi
index fdd81fdc3f35..dc919e09a505 100644
--- a/arch/arm/boot/dts/imx6dl.dtsi
+++ b/arch/arm/boot/dts/imx6dl.dtsi
@@ -80,10 +80,13 @@
 		};
 	};
 
-	soc {
+	soc: soc {
 		ocram: sram@900000 {
 			compatible = "mmio-sram";
 			reg = <0x00900000 0x20000>;
+			ranges = <0 0x00900000 0x20000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 			clocks = <&clks IMX6QDL_CLK_OCRAM>;
 		};
 
diff --git a/arch/arm/boot/dts/imx6q-apalis-eval.dts b/arch/arm/boot/dts/imx6q-apalis-eval.dts
index a0683b4aeca1..fa160a389870 100644
--- a/arch/arm/boot/dts/imx6q-apalis-eval.dts
+++ b/arch/arm/boot/dts/imx6q-apalis-eval.dts
@@ -1,6 +1,6 @@
-// SPDX-License-Identifier: GPL-2.0+ OR MIT
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
 /*
- * Copyright 2014-2020 Toradex
+ * Copyright 2014-2022 Toradex
  * Copyright 2012 Freescale Semiconductor, Inc.
  * Copyright 2011 Linaro Ltd.
  */
@@ -30,89 +30,26 @@
 		stdout-path = "serial0:115200n8";
 	};
 
-	gpio-keys {
-		compatible = "gpio-keys";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_gpio_keys>;
-
-		wakeup {
-			label = "Wake-Up";
-			gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_WAKEUP>;
-			debounce-interval = <10>;
-			wakeup-source;
-		};
-	};
-
-	lcd_display: disp0 {
-		compatible = "fsl,imx-parallel-display";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		interface-pix-fmt = "rgb24";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_ipu1_lcdif>;
-		status = "okay";
-
-		port@0 {
-			reg = <0>;
-
-			lcd_display_in: endpoint {
-				remote-endpoint = <&ipu1_di1_disp1>;
-			};
-		};
-
-		port@1 {
-			reg = <1>;
-
-			lcd_display_out: endpoint {
-				remote-endpoint = <&lcd_panel_in>;
-			};
-		};
-	};
-
-	panel: panel {
-		/*
-		 * edt,et057090dhu: EDT 5.7" LCD TFT
-		 * edt,et070080dh6: EDT 7.0" LCD TFT
-		 */
-		compatible = "edt,et057090dhu";
-		backlight = <&backlight>;
-		power-supply = <&reg_3v3_sw>;
-
-		port {
-			lcd_panel_in: endpoint {
-				remote-endpoint = <&lcd_display_out>;
-			};
-		};
-	};
-
 	reg_pcie_switch: regulator-pcie-switch {
 		compatible = "regulator-fixed";
-		regulator-name = "pcie_switch";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <1800000>;
+		enable-active-high;
 		gpio = <&gpio1 2 GPIO_ACTIVE_HIGH>;
+		regulator-max-microvolt = <1800000>;
+		regulator-min-microvolt = <1800000>;
+		regulator-name = "pcie_switch";
 		startup-delay-us = <100000>;
-		enable-active-high;
 		status = "okay";
 	};
 
 	reg_3v3_sw: regulator-3v3-sw {
 		compatible = "regulator-fixed";
-		regulator-name = "3.3V_SW";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
 		regulator-always-on;
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "3.3V_SW";
 	};
 };
 
-&backlight {
-	brightness-levels = <0 127 191 223 239 247 251 255>;
-	default-brightness-level = <1>;
-	power-supply = <&reg_3v3_sw>;
-	status = "okay";
-};
-
 &can1 {
 	xceiver-supply = <&reg_3v3_sw>;
 	status = "okay";
@@ -123,27 +60,10 @@
 	status = "okay";
 };
 
-&hdmi {
-	status = "okay";
-};
-
 /* I2C1_SDA/SCL on MXM3 209/211 (e.g. RTC on carrier board) */
 &i2c1 {
 	status = "okay";
 
-	/*
-	 * Touchscreen is using SODIMM 28/30, also used for PWM<B>, PWM<C>,
-	 * aka pwm2, pwm3. so if you enable touchscreen, disable the pwms
-	 */
-	touchscreen@4a {
-		compatible = "atmel,maxtouch";
-		reg = <0x4a>;
-		interrupt-parent = <&gpio6>;
-		interrupts = <10 IRQ_TYPE_EDGE_FALLING>;
-		reset-gpios = <&gpio6 9 GPIO_ACTIVE_LOW>; /* SODIMM 13 */
-		status = "disabled";
-	};
-
 	pcie-switch@58 {
 		compatible = "plx,pex8605";
 		reg = <0x58>;
@@ -164,14 +84,6 @@
 	status = "okay";
 };
 
-&ipu1_di1_disp1 {
-	remote-endpoint = <&lcd_display_in>;
-};
-
-&ldb {
-	status = "okay";
-};
-
 &pcie {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_reset_moci>;
@@ -198,11 +110,11 @@
 	status = "okay";
 };
 
-&reg_usb_otg_vbus {
+&reg_usb_host_vbus {
 	status = "okay";
 };
 
-&reg_usb_host_vbus {
+&reg_usb_otg_vbus {
 	status = "okay";
 };
 
@@ -246,28 +158,13 @@
 
 /* MMC1 */
 &usdhc1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc1_4bit &pinctrl_usdhc1_8bit &pinctrl_mmc_cd>;
-	cd-gpios = <&gpio4 20 GPIO_ACTIVE_LOW>;
 	status = "okay";
 };
 
 /* SD1 */
 &usdhc2 {
+	cd-gpios = <&gpio6 14 GPIO_ACTIVE_LOW>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usdhc2 &pinctrl_sd_cd>;
-	cd-gpios = <&gpio6 14 GPIO_ACTIVE_LOW>;
 	status = "okay";
 };
-
-&iomuxc {
-	/*
-	 * Mux the Apalis GPIOs
-	 */
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_apalis_gpio1 &pinctrl_apalis_gpio2
-		     &pinctrl_apalis_gpio3 &pinctrl_apalis_gpio4
-		     &pinctrl_apalis_gpio5 &pinctrl_apalis_gpio6
-		     &pinctrl_apalis_gpio7 &pinctrl_apalis_gpio8
-		    >;
-};
diff --git a/arch/arm/boot/dts/imx6q-apalis-ixora-v1.1.dts b/arch/arm/boot/dts/imx6q-apalis-ixora-v1.1.dts
index 86e84781cf5d..44637d606e61 100644
--- a/arch/arm/boot/dts/imx6q-apalis-ixora-v1.1.dts
+++ b/arch/arm/boot/dts/imx6q-apalis-ixora-v1.1.dts
@@ -1,274 +1,37 @@
-// SPDX-License-Identifier: GPL-2.0+ OR MIT
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
 /*
- * Copyright 2014-2020 Toradex
+ * Copyright 2014-2022 Toradex
  * Copyright 2012 Freescale Semiconductor, Inc.
  * Copyright 2011 Linaro Ltd.
  */
 
-/dts-v1/;
-
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/interrupt-controller/irq.h>
-#include "imx6q.dtsi"
-#include "imx6qdl-apalis.dtsi"
+#include "imx6q-apalis-ixora-v1.2.dts"
 
 / {
 	model = "Toradex Apalis iMX6Q/D Module on Ixora Carrier Board V1.1";
-	compatible = "toradex,apalis_imx6q-ixora-v1.1",
-		     "toradex,apalis_imx6q-ixora", "toradex,apalis_imx6q",
+	compatible = "toradex,apalis_imx6q-ixora-v1.1", "toradex,apalis_imx6q",
 		     "fsl,imx6q";
 
-	aliases {
-		i2c0 = &i2c1;
-		i2c1 = &i2c3;
-		i2c2 = &i2c2;
-		rtc0 = &rtc_i2c;
-		rtc1 = &snvs_rtc;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	gpio-keys {
-		compatible = "gpio-keys";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_gpio_keys>;
-
-		wakeup {
-			label = "Wake-Up";
-			gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_WAKEUP>;
-			debounce-interval = <10>;
-			wakeup-source;
-		};
-	};
-
-	lcd_display: disp0 {
-		compatible = "fsl,imx-parallel-display";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		interface-pix-fmt = "rgb24";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_ipu1_lcdif>;
-		status = "okay";
-
-		port@0 {
-			reg = <0>;
-
-			lcd_display_in: endpoint {
-				remote-endpoint = <&ipu1_di1_disp1>;
-			};
-		};
-
-		port@1 {
-			reg = <1>;
-
-			lcd_display_out: endpoint {
-				remote-endpoint = <&lcd_panel_in>;
-			};
-		};
-	};
 
-	panel: panel {
-		/*
-		 * edt,et057090dhu: EDT 5.7" LCD TFT
-		 * edt,et070080dh6: EDT 7.0" LCD TFT
-		 */
-		compatible = "edt,et057090dhu";
-		backlight = <&backlight>;
-
-		port {
-			lcd_panel_in: endpoint {
-				remote-endpoint = <&lcd_display_out>;
-			};
-		};
-	};
-
-	leds {
-		compatible = "gpio-leds";
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_leds_ixora>;
-
-		led4-green {
-			label = "LED_4_GREEN";
-			gpios = <&gpio1 14 GPIO_ACTIVE_HIGH>;
-		};
-
-		led4-red {
-			label = "LED_4_RED";
-			gpios = <&gpio1 12 GPIO_ACTIVE_HIGH>;
-		};
-
-		led5-green {
-			label = "LED_5_GREEN";
-			gpios = <&gpio2 1 GPIO_ACTIVE_HIGH>;
-		};
-
-		led5-red {
-			label = "LED_5_RED";
-			gpios = <&gpio2 2 GPIO_ACTIVE_HIGH>;
-		};
-	};
 };
 
-&backlight {
-	brightness-levels = <0 127 191 223 239 247 251 255>;
-	default-brightness-level = <1>;
-	status = "okay";
-};
+/delete-node/ &eeprom;
+/delete-node/ &reg_3v3_vmmc;
+/delete-node/ &reg_can1_supply;
+/delete-node/ &reg_can2_supply;
 
 &can1 {
-	status = "okay";
+	/delete-property/ xceiver-supply;
 };
 
 &can2 {
-	status = "okay";
-};
-
-&hdmi {
-	status = "okay";
-};
-
-/* I2C1_SDA/SCL on MXM3 209/211 (e.g. RTC on carrier board) */
-&i2c1 {
-	status = "okay";
-
-	/*
-	 * Touchscreen is using SODIMM 28/30, also used for PWM<B>, PWM<C>,
-	 * aka pwm2, pwm3. so if you enable touchscreen, disable the pwms
-	 */
-	touchscreen@4a {
-		compatible = "atmel,maxtouch";
-		reg = <0x4a>;
-		interrupt-parent = <&gpio6>;
-		interrupts = <10 IRQ_TYPE_EDGE_FALLING>;
-		reset-gpios = <&gpio6 9 GPIO_ACTIVE_LOW>; /* SODIMM 13 */
-		status = "disabled";
-	};
-
-	/* M41T0M6 real time clock on carrier board */
-	rtc_i2c: rtc@68 {
-		compatible = "st,m41t0";
-		reg = <0x68>;
-	};
-};
-
-/*
- * I2C3_SDA/SCL (CAM) on MXM3 pin 201/203 (e.g. camera sensor on carrier
- * board)
- */
-&i2c3 {
-	status = "okay";
-};
-
-&ipu1_di1_disp1 {
-	remote-endpoint = <&lcd_display_in>;
-};
-
-&ldb {
-	status = "okay";
-};
-
-&pcie {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_reset_moci>;
-	/* active-high meaning opposite of regular PERST# active-low polarity */
-	reset-gpio = <&gpio1 28 GPIO_ACTIVE_HIGH>;
-	reset-gpio-active-high;
-	status = "okay";
-};
-
-&pwm1 {
-	status = "okay";
-};
-
-&pwm2 {
-	status = "okay";
-};
-
-&pwm3 {
-	status = "okay";
-};
-
-&pwm4 {
-	status = "okay";
-};
-
-&reg_usb_otg_vbus {
-	status = "okay";
-};
-
-&reg_usb_host_vbus {
-	status = "okay";
-};
-
-&sata {
-	status = "okay";
-};
-
-&sound_spdif {
-	status = "okay";
-};
-
-&spdif {
-	status = "okay";
-};
-
-&uart1 {
-	status = "okay";
-};
-
-&uart2 {
-	status = "okay";
-};
-
-&uart4 {
-	status = "okay";
-};
-
-&uart5 {
-	status = "okay";
-};
-
-&usbh1 {
-	vbus-supply = <&reg_usb_host_vbus>;
-	status = "okay";
-};
-
-&usbotg {
-	vbus-supply = <&reg_usb_otg_vbus>;
-	status = "okay";
+	/delete-property/ xceiver-supply;
 };
 
 /* MMC1 */
 &usdhc1 {
+	/delete-property/ cap-power-off-card;
+	/delete-property/ pinctrl-1;
+	/delete-property/ vmmc-supply;
 	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc1_4bit &pinctrl_mmc_cd>;
-	cd-gpios = <&gpio4 20 GPIO_ACTIVE_LOW>;
-	bus-width = <4>;
-	status = "okay";
-};
-
-&iomuxc {
-	/*
-	 * Mux the Apalis GPIOs
-	 */
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_apalis_gpio1 &pinctrl_apalis_gpio2
-		     &pinctrl_apalis_gpio3 &pinctrl_apalis_gpio4
-		     &pinctrl_apalis_gpio5 &pinctrl_apalis_gpio6
-		     &pinctrl_apalis_gpio7 &pinctrl_apalis_gpio8
-		    >;
-
-	pinctrl_leds_ixora: ledsixoragrp {
-		fsl,pins = <
-			MX6QDL_PAD_SD2_DAT1__GPIO1_IO14 0x1b0b0
-			MX6QDL_PAD_SD2_DAT3__GPIO1_IO12 0x1b0b0
-			MX6QDL_PAD_NANDF_D1__GPIO2_IO01 0x1b0b0
-			MX6QDL_PAD_NANDF_D2__GPIO2_IO02 0x1b0b0
-		>;
-	};
 };
diff --git a/arch/arm/boot/dts/imx6q-apalis-ixora-v1.2.dts b/arch/arm/boot/dts/imx6q-apalis-ixora-v1.2.dts
new file mode 100644
index 000000000000..f9f7d99bd4db
--- /dev/null
+++ b/arch/arm/boot/dts/imx6q-apalis-ixora-v1.2.dts
@@ -0,0 +1,276 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2014-2022 Toradex
+ * Copyright 2012 Freescale Semiconductor, Inc.
+ * Copyright 2011 Linaro Ltd.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include "imx6q.dtsi"
+#include "imx6qdl-apalis.dtsi"
+
+/ {
+	model = "Toradex Apalis iMX6Q/D Module on Ixora Carrier Board V1.2";
+	compatible = "toradex,apalis_imx6q-ixora-v1.2", "toradex,apalis_imx6q",
+		     "fsl,imx6q";
+
+	aliases {
+		i2c0 = &i2c1;
+		i2c1 = &i2c3;
+		i2c2 = &i2c2;
+		rtc0 = &rtc_i2c;
+		rtc1 = &snvs_rtc;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_leds_ixora>;
+
+		led4-green {
+			gpios = <&gpio1 14 GPIO_ACTIVE_HIGH>;
+			label = "LED_4_GREEN";
+		};
+
+		led4-red {
+			gpios = <&gpio1 12 GPIO_ACTIVE_HIGH>;
+			label = "LED_4_RED";
+		};
+
+		led5-green {
+			gpios = <&gpio2 1 GPIO_ACTIVE_HIGH>;
+			label = "LED_5_GREEN";
+		};
+
+		led5-red {
+			gpios = <&gpio2 2 GPIO_ACTIVE_HIGH>;
+			label = "LED_5_RED";
+		};
+	};
+
+	reg_3v3_vmmc: regulator-3v3-vmmc {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio2 0 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_enable_3v3_vmmc>;
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "3v3_vmmc";
+		startup-delay-us = <100>;
+	};
+
+	reg_can1_supply: regulator-can1-supply {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio2 3 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_enable_can1_power>;
+		regulator-name = "can1_supply";
+	};
+
+	reg_can2_supply: regulator-can2-supply {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio3 15 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_enable_can2_power>;
+		regulator-name = "can2_supply";
+	};
+};
+
+&can1 {
+	xceiver-supply = <&reg_can1_supply>;
+	status = "okay";
+};
+
+&can2 {
+	xceiver-supply = <&reg_can2_supply>;
+	status = "okay";
+};
+
+&gpio1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart24_forceoff>;
+
+	/*
+	 * uart-2-4-on-x21-enable-hog enables the UART transceiver for Apalis
+	 * UART2 and UART3. If one wants to disable the transceiver force
+	 * the GPIO to output-low, if one wants to control the transceiver
+	 * from user space delete the hog node.
+	 */
+	uart-2-4-on-x21-enable-hog {
+		gpio-hog;
+		gpios = <11 GPIO_ACTIVE_HIGH>; /* MXM3 180 */
+		output-high;
+	};
+};
+
+/* I2C1_SDA/SCL on MXM3 209/211 (e.g. RTC on carrier board) */
+&i2c1 {
+	status = "okay";
+
+	/* M41T0M6 real time clock on carrier board */
+	rtc_i2c: rtc@68 {
+		compatible = "st,m41t0";
+		reg = <0x68>;
+	};
+
+	eeprom: eeprom@50 {
+		compatible = "atmel,24c02";
+		reg = <0x50>;
+		pagesize = <16>;
+	};
+};
+
+/*
+ * I2C3_SDA/SCL (CAM) on MXM3 pin 201/203 (e.g. camera sensor on carrier
+ * board)
+ */
+&i2c3 {
+	status = "okay";
+};
+
+&pcie {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_reset_moci>;
+	/* active-high meaning opposite of regular PERST# active-low polarity */
+	reset-gpio = <&gpio1 28 GPIO_ACTIVE_HIGH>;
+	reset-gpio-active-high;
+	status = "okay";
+};
+
+&pwm1 {
+	status = "okay";
+};
+
+&pwm2 {
+	status = "okay";
+};
+
+&pwm3 {
+	status = "okay";
+};
+
+&pwm4 {
+	status = "okay";
+};
+
+&reg_usb_host_vbus {
+	status = "okay";
+};
+
+&reg_usb_otg_vbus {
+	status = "okay";
+};
+
+&sata {
+	status = "okay";
+};
+
+&sound_spdif {
+	status = "okay";
+};
+
+&spdif {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&uart4 {
+	status = "okay";
+};
+
+&uart5 {
+	status = "okay";
+};
+
+&usbh1 {
+	vbus-supply = <&reg_usb_host_vbus>;
+	status = "okay";
+};
+
+&usbotg {
+	vbus-supply = <&reg_usb_otg_vbus>;
+	status = "okay";
+};
+
+/* MMC1 */
+&usdhc1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&pinctrl_usdhc1_4bit &pinctrl_mmc_cd>;
+	pinctrl-1 = <&pinctrl_usdhc1_4bit_sleep &pinctrl_mmc_cd_sleep>;
+	bus-width = <4>;
+	cap-power-off-card;
+	vmmc-supply = <&reg_3v3_vmmc>;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_enable_3v3_vmmc: enable3v3vmmcgrp {
+		fsl,pins = <
+			MX6QDL_PAD_NANDF_D0__GPIO2_IO00 0x1b0b0
+		>;
+	};
+
+	pinctrl_enable_can1_power: enablecan1powergrp {
+		fsl,pins = <
+			MX6QDL_PAD_NANDF_D3__GPIO2_IO03 0x1b0b0
+		>;
+	};
+
+	pinctrl_enable_can2_power: enablecan2powergrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_DA15__GPIO3_IO15 0x1b0b0
+		>;
+	};
+
+	pinctrl_uart24_forceoff: uart24forceoffgrp {
+		fsl,pins = <
+			MX6QDL_PAD_SD2_CMD__GPIO1_IO11 0x1b0b0
+		>;
+	};
+
+	pinctrl_leds_ixora: ledsixoragrp {
+		fsl,pins = <
+			MX6QDL_PAD_SD2_DAT1__GPIO1_IO14 0x1b0b0
+			MX6QDL_PAD_SD2_DAT3__GPIO1_IO12 0x1b0b0
+			MX6QDL_PAD_NANDF_D1__GPIO2_IO01 0x1b0b0
+			MX6QDL_PAD_NANDF_D2__GPIO2_IO02 0x1b0b0
+		>;
+	};
+
+	pinctrl_mmc_cd_sleep: mmccdslpgrp {
+		fsl,pins = <
+			 /* MMC1 CD */
+			MX6QDL_PAD_DI0_PIN4__GPIO4_IO20 0x0
+		>;
+	};
+
+	pinctrl_usdhc1_4bit_sleep: usdhc1-4bitslpgrp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_CMD__SD1_CMD     0x3000
+			MX6QDL_PAD_SD1_CLK__SD1_CLK     0x3000
+			MX6QDL_PAD_SD1_DAT0__SD1_DATA0  0x3000
+			MX6QDL_PAD_SD1_DAT1__SD1_DATA1  0x3000
+			MX6QDL_PAD_SD1_DAT2__SD1_DATA2  0x3000
+			MX6QDL_PAD_SD1_DAT3__SD1_DATA3  0x3000
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6q-apalis-ixora.dts b/arch/arm/boot/dts/imx6q-apalis-ixora.dts
index 62e72773e53b..ce39c6a3f640 100644
--- a/arch/arm/boot/dts/imx6q-apalis-ixora.dts
+++ b/arch/arm/boot/dts/imx6q-apalis-ixora.dts
@@ -1,6 +1,6 @@
-// SPDX-License-Identifier: GPL-2.0+ OR MIT
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
 /*
- * Copyright 2014-2020 Toradex
+ * Copyright 2014-2022 Toradex
  * Copyright 2012 Freescale Semiconductor, Inc.
  * Copyright 2011 Linaro Ltd.
  */
@@ -30,95 +30,33 @@
 		stdout-path = "serial0:115200n8";
 	};
 
-	gpio-keys {
-		compatible = "gpio-keys";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_gpio_keys>;
-
-		wakeup {
-			label = "Wake-Up";
-			gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_WAKEUP>;
-			debounce-interval = <10>;
-			wakeup-source;
-		};
-	};
-
-	lcd_display: disp0 {
-		compatible = "fsl,imx-parallel-display";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		interface-pix-fmt = "rgb24";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_ipu1_lcdif>;
-		status = "okay";
-
-		port@0 {
-			reg = <0>;
-
-			lcd_display_in: endpoint {
-				remote-endpoint = <&ipu1_di1_disp1>;
-			};
-		};
-
-		port@1 {
-			reg = <1>;
-
-			lcd_display_out: endpoint {
-				remote-endpoint = <&lcd_panel_in>;
-			};
-		};
-	};
-
-	panel: panel {
-		/*
-		 * edt,et057090dhu: EDT 5.7" LCD TFT
-		 * edt,et070080dh6: EDT 7.0" LCD TFT
-		 */
-		compatible = "edt,et057090dhu";
-		backlight = <&backlight>;
-
-		port {
-			lcd_panel_in: endpoint {
-				remote-endpoint = <&lcd_display_out>;
-			};
-		};
-	};
-
 	leds {
 		compatible = "gpio-leds";
-
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_leds_ixora>;
 
 		led4-green {
-			label = "LED_4_GREEN";
 			gpios = <&gpio1 17 GPIO_ACTIVE_HIGH>;
+			label = "LED_4_GREEN";
 		};
 
 		led4-red {
-			label = "LED_4_RED";
 			gpios = <&gpio1 21 GPIO_ACTIVE_HIGH>;
+			label = "LED_4_RED";
 		};
 
 		led5-green {
-			label = "LED_5_GREEN";
 			gpios = <&gpio2 1 GPIO_ACTIVE_HIGH>;
+			label = "LED_5_GREEN";
 		};
 
 		led5-red {
-			label = "LED_5_RED";
 			gpios = <&gpio2 2 GPIO_ACTIVE_HIGH>;
+			label = "LED_5_RED";
 		};
 	};
 };
 
-&backlight {
-	brightness-levels = <0 127 191 223 239 247 251 255>;
-	default-brightness-level = <1>;
-	status = "okay";
-};
-
 &can1 {
 	status = "okay";
 };
@@ -127,27 +65,10 @@
 	status = "okay";
 };
 
-&hdmi {
-	status = "okay";
-};
-
 /* I2C1_SDA/SCL on MXM3 209/211 (e.g. RTC on carrier board) */
 &i2c1 {
 	status = "okay";
 
-	/*
-	 * Touchscreen is using SODIMM 28/30, also used for PWM<B>, PWM<C>,
-	 * aka pwm2, pwm3. so if you enable touchscreen, disable the pwms
-	 */
-	touchscreen@4a {
-		compatible = "atmel,maxtouch";
-		reg = <0x4a>;
-		interrupt-parent = <&gpio6>;
-		interrupts = <10 IRQ_TYPE_EDGE_FALLING>;
-		reset-gpios = <&gpio6 9 GPIO_ACTIVE_LOW>; /* SODIMM 13 */
-		status = "disabled";
-	};
-
 	eeprom@50 {
 		compatible = "atmel,24c02";
 		reg = <0x50>;
@@ -168,14 +89,6 @@
 	status = "okay";
 };
 
-&ipu1_di1_disp1 {
-	remote-endpoint = <&lcd_display_in>;
-};
-
-&ldb {
-	status = "okay";
-};
-
 &pcie {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_reset_moci>;
@@ -201,11 +114,11 @@
 	status = "okay";
 };
 
-&reg_usb_otg_vbus {
+&reg_usb_host_vbus {
 	status = "okay";
 };
 
-&reg_usb_host_vbus {
+&reg_usb_otg_vbus {
 	status = "okay";
 };
 
@@ -249,21 +162,13 @@
 
 /* SD1 */
 &usdhc2 {
+	cd-gpios = <&gpio6 14 GPIO_ACTIVE_LOW>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usdhc2 &pinctrl_sd_cd>;
-	cd-gpios = <&gpio6 14 GPIO_ACTIVE_LOW>;
 	status = "okay";
 };
 
 &iomuxc {
-	/* Mux the Apalis GPIOs */
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_apalis_gpio1 &pinctrl_apalis_gpio2
-		     &pinctrl_apalis_gpio3 &pinctrl_apalis_gpio4
-		     &pinctrl_apalis_gpio5 &pinctrl_apalis_gpio6
-		     &pinctrl_apalis_gpio7 &pinctrl_apalis_gpio8
-		    >;
-
 	pinctrl_leds_ixora: ledsixoragrp {
 		fsl,pins = <
 			MX6QDL_PAD_SD1_DAT1__GPIO1_IO17 0x1b0b0
diff --git a/arch/arm/boot/dts/imx6q-arm2.dts b/arch/arm/boot/dts/imx6q-arm2.dts
index 0b40f52268b3..75586299d9ca 100644
--- a/arch/arm/boot/dts/imx6q-arm2.dts
+++ b/arch/arm/boot/dts/imx6q-arm2.dts
@@ -178,6 +178,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
 	phy-mode = "rgmii";
+	/delete-property/ interrupts;
 	interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
 			      <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
 	fsl,err006687-workaround-present;
diff --git a/arch/arm/boot/dts/imx6q-ba16.dtsi b/arch/arm/boot/dts/imx6q-ba16.dtsi
index 6330d75f8f39..f266f1b7e0cf 100644
--- a/arch/arm/boot/dts/imx6q-ba16.dtsi
+++ b/arch/arm/boot/dts/imx6q-ba16.dtsi
@@ -142,7 +142,7 @@
 	pinctrl-0 = <&pinctrl_ecspi1>;
 	status = "okay";
 
-	flash: n25q032@0 {
+	flash: flash@0 {
 		compatible = "jedec,spi-nor";
 		#address-cells = <1>;
 		#size-cells = <1>;
diff --git a/arch/arm/boot/dts/imx6q-bosch-acc.dts b/arch/arm/boot/dts/imx6q-bosch-acc.dts
new file mode 100644
index 000000000000..8263bfef9bf8
--- /dev/null
+++ b/arch/arm/boot/dts/imx6q-bosch-acc.dts
@@ -0,0 +1,779 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Support for the i.MX6-based Bosch ACC board.
+ *
+ * Copyright (C) 2016 Garz & Fricke GmbH
+ * Copyright (C) 2018 DENX Software Engineering GmbH, Heiko Schocher <hs@denx.de>
+ * Copyright (C) 2018 DENX Software Engineering GmbH, Niel Fourie <lusus@denx.de>
+ * Copyright (C) 2019-2021 Bosch Thermotechnik GmbH, Matthias Winker <matthias.winker@bosch.com>
+ * Copyright (C) 2022 DENX Software Engineering GmbH, Philip Oberfichtner <pro@denx.de>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include "imx6q.dtsi"
+
+/ {
+	model = "Bosch ACC";
+	compatible = "bosch,imx6q-acc", "fsl,imx6q";
+
+	aliases {
+		i2c0 = &i2c1;
+		i2c1 = &i2c2;
+		i2c2 = &i2c3;
+		mmc0 = &usdhc4;
+		mmc1 = &usdhc2;
+		serial0 = &uart2;
+		serial1 = &uart1;
+	};
+
+	memory@10000000 {
+		device_type = "memory";
+		reg = <0x10000000 0x40000000>;
+	};
+
+	backlight_lvds: backlight-lvds {
+		compatible = "pwm-backlight";
+		pwms = <&pwm1 0 200000>;
+		brightness-levels = <0 61 499 1706 4079 8022 13938 22237 33328 47623 65535>;
+		num-interpolated-steps = <10>;
+		default-brightness-level = <60>;
+		power-supply = <&reg_lcd>;
+	};
+
+	panel {
+		compatible = "dataimage,fg1001l0dsswmg01";
+		backlight = <&backlight_lvds>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&lvds0_out>;
+			};
+		};
+	};
+
+	refclk: refclk {
+		compatible = "fixed-factor-clock";
+		#clock-cells = <0>;
+		clocks = <&clks IMX6QDL_CLK_CKO2>;
+		clock-div = <1>;
+		clock-mult = <1>;
+		clock-output-names = "12mhz_refclk";
+		assigned-clocks = <&clks IMX6QDL_CLK_CKO>,
+				  <&clks IMX6QDL_CLK_CKO2>,
+				  <&clks IMX6QDL_CLK_CKO2_SEL>;
+		assigned-clock-parents = <&clks IMX6QDL_CLK_CKO2>,
+					 <&clks IMX6QDL_CLK_CKO2_PODF>,
+					 <&clks IMX6QDL_CLK_OSC>;
+		assigned-clock-rates = <0>, <12000000>, <0>;
+	};
+
+	cpus {
+		cpu0: cpu@0 {
+			operating-points = <
+				/* kHz    uV */
+				1200000 1275000
+				996000  1225000
+				852000  1225000
+				792000  1150000
+				396000  950000
+			>;
+			fsl,soc-operating-points = <
+				/* ARM kHz  SOC-PU uV */
+				1200000 1225000
+				996000	1175000
+				852000	1175000
+				792000	1150000
+				396000	1150000
+			>;
+		};
+
+		cpu1: cpu@1 {
+			operating-points = <
+				/* kHz    uV */
+				1200000 1275000
+				996000  1225000
+				852000  1225000
+				792000  1150000
+				396000  950000
+			>;
+			fsl,soc-operating-points = <
+				/* ARM kHz  SOC-PU uV */
+				1200000 1225000
+				996000	1175000
+				852000	1175000
+				792000	1150000
+				396000	1150000
+			>;
+		};
+	};
+
+	pwm-leds {
+		compatible = "pwm-leds";
+
+		led_red: led-0 {
+			color = <LED_COLOR_ID_RED>;
+			max-brightness = <248>;
+			default-state = "off";
+			pwms = <&pwm2 0 500000>;
+		};
+
+		led_white: led-1 {
+			color = <LED_COLOR_ID_WHITE>;
+			max-brightness = <248>;
+			default-state = "off";
+			pwms = <&pwm3 0 500000>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reset_gpio_led>;
+
+		led-2 {
+			color = <LED_COLOR_ID_RED>;
+			gpios = <&gpio5 18 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+	};
+
+	reg_5p0: regulator-5p0 {
+		compatible = "regulator-fixed";
+		regulator-name = "5p0";
+	};
+
+	reg_vin: regulator-vin {
+		compatible = "regulator-fixed";
+		regulator-name = "VIN";
+		regulator-min-microvolt = <4500000>;
+		regulator-max-microvolt = <4500000>;
+		regulator-always-on;
+		vin-supply = <&reg_5p0>;
+	};
+
+	reg_usb_otg_vbus: regulator-usb-otg-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_otg_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	reg_usb_h1_vbus: regulator-usb-h1-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_h1_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		vin-supply = <&reg_5p0>;
+	};
+
+	reg_usb_h2_vbus: regulator-usb-h2-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_h2_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&reg_5p0> ;
+		regulator-always-on;
+	};
+
+	reg_vsnvs: regulator-vsnvs {
+		compatible = "regulator-fixed";
+		regulator-name = "VSNVS_3V0";
+		regulator-min-microvolt = <3000000>;
+		regulator-max-microvolt = <3000000>;
+		regulator-always-on;
+		vin-supply = <&reg_5p0>;
+	};
+
+	reg_lcd: regulator-lcd {
+		compatible = "regulator-fixed";
+		regulator-name = "LCD0 POWER";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_lcd_enable>;
+		gpio = <&gpio3 23 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-boot-on;
+	};
+
+	reg_dac: regulator-dac {
+		compatible = "regulator-fixed";
+		regulator-name = "vref_dac";
+		regulator-min-microvolt = <20000>;
+		regulator-max-microvolt = <20000>;
+		vin-supply = <&reg_5p0> ;
+		regulator-boot-on;
+	};
+
+	reg_sw4: regulator-sw4 {
+		compatible = "regulator-fixed";
+		regulator-name = "SW4_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		vin-supply = <&reg_5p0>;
+	};
+
+	reg_sys: regulator-sys {
+		compatible = "regulator-fixed";
+		regulator-name = "SYS_4V2";
+		regulator-min-microvolt = <4200000>;
+		regulator-max-microvolt = <4200000>;
+		regulator-always-on;
+		vin-supply = <&reg_5p0>;
+	};
+};
+
+&reg_arm {
+	vin-supply = <&sw2_reg>;
+};
+
+&reg_soc {
+	vin-supply = <&sw1c_reg>;
+};
+
+&reg_vdd1p1 {
+	vin-supply = <&reg_vsnvs>;
+};
+
+&reg_vdd2p5 {
+	vin-supply = <&reg_vsnvs>;
+};
+
+&reg_vdd3p0 {
+	vin-supply = <&reg_vsnvs>;
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet>;
+	clocks = <&clks IMX6QDL_CLK_ENET>,
+		<&clks IMX6QDL_CLK_ENET>,
+		<&clks IMX6QDL_CLK_ENET>,
+		<&clks IMX6QDL_CLK_ENET_REF>;
+	clock-names = "ipg", "ahb", "ptp", "enet_out";
+	phy-mode = "rmii";
+	phy-supply = <&reg_sw4>;
+	phy-handle = <&ethphy>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy: ethernet-phy@0 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <0>;
+			interrupt-parent = <&gpio1>;
+			interrupts = <23 IRQ_TYPE_EDGE_FALLING>;
+			smsc,disable-energy-detect;
+		};
+	};
+};
+
+&gpu_vg {
+	status = "disabled";
+};
+
+&gpu_2d {
+	status = "disabled";
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	clock-frequency = <400000>;
+	status = "okay";
+
+	pmic: pmic@8 {
+		compatible = "fsl,pfuze100";
+		reg = <0x08>;
+
+		regulators {
+			sw1c_reg: sw1c {
+				regulator-name = "VDD_SOC (sw1abc)";
+				regulator-min-microvolt = <1275000>;
+				regulator-max-microvolt = <1500000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <6250>;
+			};
+
+			sw2_reg: sw2 {
+				regulator-name = "VDD_ARM (sw2)";
+				regulator-min-microvolt = <1050000>;
+				regulator-max-microvolt = <1500000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <6250>;
+			};
+
+			sw3a_reg: sw3a {
+				compatible = "regulator-fixed";
+				regulator-name = "DDR_1V5a";
+				regulator-boot-on;
+				regulator-always-on;
+
+			};
+
+			sw3b_reg: sw3b {
+				compatible = "regulator-fixed";
+				regulator-name = "DDR_1V5b";
+				regulator-boot-on;
+				regulator-always-on;
+
+			};
+
+			sw4_reg: sw4 {
+				regulator-name = "AUX 3V15 (sw4)";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			swbst_reg: swbst {
+				regulator-min-microvolt = <5000000>;
+				regulator-max-microvolt = <5150000>;
+				regulator-boot-on;
+				regulator-always-on;
+				status = "disabled";
+			};
+
+			snvs_reg: vsnvs {
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			vref_reg: vrefddr {
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			vgen1_reg: vgen1 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1550000>;
+				regulator-always-on;
+			};
+
+			vgen2_reg: vgen2 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1550000>;
+				regulator-always-on;
+			};
+
+			vgen3_reg: vgen3 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			vgen4_reg: vgen4 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			vgen5_reg: vgen5 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			vgen6_reg: vgen6 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+		};
+	};
+
+	lm75: sensor@49 {
+		compatible = "national,lm75b";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_lm75>;
+		reg = <0x49>;
+	};
+
+	eeprom: eeprom@50 {
+		compatible = "atmel,24c32";
+		reg = <0x50>;
+		pagesize = <32>;
+	};
+
+	rtc: rtc@51 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_rtc>;
+		compatible = "nxp,pcf8563";
+		reg = <0x51>;
+	};
+};
+
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	clock-frequency = <100000>;
+	status = "okay";
+
+	eeprom_ext: eeprom@50 {
+		compatible = "atmel,24c32";
+		reg = <0x50>;
+		pagesize = <32>;
+	};
+};
+
+&i2c3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	clock-frequency = <400000>;
+	status = "okay";
+
+	usb3503: usb@8 {
+		compatible = "smsc,usb3503";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usb3503>;
+		reg = <0x08>;
+		connect-gpios = <&gpio1 16 GPIO_ACTIVE_HIGH>; /* Old: 0, SS: HIGH */
+		intn-gpios = <&gpio7 12 GPIO_ACTIVE_LOW>; /* Old: 1, SS: HIGH */
+		reset-gpios = <&gpio5 5 GPIO_ACTIVE_LOW>; /* Old: 0, SS: HIGH */
+		initial-mode = <1>;
+		clocks = <&refclk>;
+		clock-names = "refclk";
+		refclk-frequency = <12000000>;
+	};
+
+	exc3000: touchscreen@2a {
+		compatible = "eeti,exc3000";
+		reg = <0x2a>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ctouch>;
+		interrupt-parent = <&gpio4>;
+		interrupts = <6 IRQ_TYPE_LEVEL_LOW>;
+		touchscreen-size-x = <4096>;
+		touchscreen-size-y = <4096>;
+	};
+
+	vcnl4035: light-sensor@60 {
+		compatible = "vishay,vcnl4035";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_proximity>;
+		reg = <0x60>;
+	};
+};
+
+&ldb {
+	status = "okay";
+
+	lvds0: lvds-channel@0 {
+		fsl,data-mapping = "spwg";
+		fsl,data-width = <24>;
+
+		port@4 {
+			reg = <4>;
+
+			lvds0_out: endpoint {
+				remote-endpoint = <&panel_in>;
+			};
+		};
+	};
+};
+
+&pwm1 {
+	#pwm-cells = <2>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm1>;
+	status = "okay";
+};
+
+&pwm2 {
+	#pwm-cells = <2>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm2>;
+	status = "okay";
+};
+
+&pwm3 {
+	#pwm-cells = <2>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm3>;
+	status = "okay";
+};
+
+&pwm4 {
+	#pwm-cells = <2>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm4>;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	rts-gpios = <&gpio7 8 GPIO_ACTIVE_HIGH>;
+	linux,rs485-enabled-at-boot-time;
+	rs485-rx-during-tx;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&usbh1 {
+	vbus-supply = <&reg_usb_h1_vbus>;
+	status = "okay";
+};
+
+&usbh2 {
+	pinctrl-names = "idle", "active";
+	pinctrl-0 = <&pinctrl_usbh2_idle>;
+	pinctrl-1 = <&pinctrl_usbh2_active>;
+	vbus-supply = <&reg_usb_h2_vbus>;
+	status = "okay";
+};
+
+&usbotg {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg>;
+	vbus-supply = <&reg_usb_otg_vbus>;
+	disable-over-current;
+	dr_mode = "otg";
+	srp-disable;
+	hnp-disable;
+	adp-disable;
+	status = "okay";
+};
+
+&usbphynop1 {
+	clocks = <&clks IMX6QDL_CLK_USBPHY1>;
+	clock-names = "main_clk";
+	vcc-supply = <&reg_usb_h1_vbus>;
+};
+
+&usbphynop2 {
+	vcc-supply = <&reg_usb_h2_vbus>;
+};
+
+&usdhc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	cd-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
+	no-1-8-v;
+	keep-power-in-suspend;
+	wakeup-source;
+	voltage-ranges = <3300 3300>;
+	vmmc-supply = <&reg_sw4>;
+	fsl,wp-controller;
+	status = "okay";
+};
+
+&usdhc4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc4>;
+	bus-width = <8>;
+	non-removable;
+	no-1-8-v;
+	keep-power-in-suspend;
+	voltage-ranges = <3300 3300>;
+	vmmc-supply = <&reg_sw4>;
+	fsl,wp-controller;
+	status = "okay";
+};
+
+&wdog1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog1>;
+	fsl,ext-reset-output;
+	timeout-sec = <10>;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_enet: enetgrp {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_MDC__ENET_MDC		0x1b0b0
+			MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x1b0b0
+			MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN	0x1b0b0
+			MX6QDL_PAD_ENET_REF_CLK__GPIO1_IO23	0x1b0b0	/* FEC INT */
+			MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER	0x1b0b0
+			MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN	0x0001b098
+			MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0	0x1b0b0
+			MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1	0x1b0b0
+			MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1	0x0001b098
+			MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0	0x0001b098
+			MX6QDL_PAD_GPIO_16__ENET_REF_CLK	0x4001b0a8
+		>;
+	};
+
+	pinctrl_reset_gpio_led: reset-gpio-led-grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_PIXCLK__GPIO5_IO18		0x1b0b0
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001b8b1
+			MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001b8b1
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b810
+			MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b810
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_5__I2C3_SCL  0x4001b8b1
+			MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1
+		>;
+	};
+
+	pinctrl_lcd_enable: lcdenablegrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D23__GPIO3_IO23  0x1b0b0 /* lcd enable */
+			MX6QDL_PAD_EIM_D16__GPIO3_IO16  0x1b0b0 /* sel6_8 */
+		>;
+	};
+
+	pinctrl_lm75: lm75grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_ROW0__GPIO4_IO07		0x1b0b0
+		>;
+	};
+
+	pinctrl_proximity: proximitygrp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_ROW2__GPIO4_IO11  0x1b0b0
+		>;
+	};
+
+	pinctrl_pwm1: pwm1grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_DAT3__PWM1_OUT 0x0001b0b0
+		>;
+	};
+
+	pinctrl_pwm2: pwm2grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_DAT2__PWM2_OUT 0x0001b0b0
+		>;
+	};
+
+	pinctrl_pwm3: pwm3grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_DAT1__PWM3_OUT 0x0001b0b0
+		>;
+	};
+
+	pinctrl_pwm4: pwm4grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_CMD__PWM4_OUT 0x0001b0b0
+		>;
+	};
+
+	pinctrl_rtc: rtc-grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL1__GPIO4_IO08 0x1b0b0 /* RTC INT */
+		>;
+	};
+
+	pinctrl_ctouch: ctouch-grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL0__GPIO4_IO06 0x1b0b0 /* CTOUCH_INT */
+			MX6QDL_PAD_SD1_CLK__GPIO1_IO20 0x0001b0b0 /* CTOUCH_RESET */
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_DAT6__UART1_RX_DATA 0x1b0b1
+			MX6QDL_PAD_SD3_DAT7__UART1_TX_DATA 0x1b0b1
+			MX6QDL_PAD_SD3_RST__GPIO7_IO08 0x0001b0b0
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_DAT4__UART2_RX_DATA 0x1b0b1
+			MX6QDL_PAD_SD3_DAT5__UART2_TX_DATA 0x1b0b1
+			MX6QDL_PAD_EIM_D28__UART2_CTS_B 0x1b0b1
+			MX6QDL_PAD_EIM_D29__UART2_RTS_B 0x1b0b1
+		>;
+	};
+
+	pinctrl_usbh2_idle: usbh2-idle-grp {
+		fsl,pins = <
+			MX6QDL_PAD_RGMII_TXC__USB_H2_DATA      0x00013018
+			MX6QDL_PAD_RGMII_TX_CTL__USB_H2_STROBE 0x00013018
+		>;
+	};
+
+	pinctrl_usbh2_active: usbh2-active-grp {
+		fsl,pins = <
+			MX6QDL_PAD_RGMII_TXC__USB_H2_DATA      0x00013018
+			MX6QDL_PAD_RGMII_TX_CTL__USB_H2_STROBE 0x00017018
+		>;
+	};
+
+	pinctrl_usb3503: usb3503-grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_MCLK__CCM_CLKO1    0x00000018
+			MX6QDL_PAD_GPIO_17__GPIO7_IO12     0x1b0b0 /* USB INT */
+			MX6QDL_PAD_DISP0_DAT11__GPIO5_IO05 0x0001b0b0 /* USB Reset */
+			MX6QDL_PAD_SD1_DAT0__GPIO1_IO16    0x1b0b0 /* USB Connect */
+		>;
+	};
+
+	pinctrl_usbotg: usbotggrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_1__USB_OTG_ID	0x17059
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD2_CMD__SD2_CMD    0x00017069
+			MX6QDL_PAD_SD2_CLK__SD2_CLK    0x00010038
+			MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x00017069
+			MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x00017069
+			MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x00017069
+			MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x00017069
+			MX6QDL_PAD_GPIO_4__SD2_CD_B    0x0001b0b0
+		>;
+	};
+
+	pinctrl_usdhc4: usdhc4grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD4_CMD__SD4_CMD    0x00017059
+			MX6QDL_PAD_SD4_CLK__SD4_CLK    0x00010059
+			MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x00017059
+			MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x00017059
+			MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x00017059
+			MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x00017059
+			MX6QDL_PAD_SD4_DAT4__SD4_DATA4 0x00017059
+			MX6QDL_PAD_SD4_DAT5__SD4_DATA5 0x00017059
+			MX6QDL_PAD_SD4_DAT6__SD4_DATA6 0x00017059
+			MX6QDL_PAD_SD4_DAT7__SD4_DATA7 0x00017059
+		>;
+	};
+
+	pinctrl_wdog1: wdoggrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_9__WDOG1_B 0x1b0b0
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6q-bx50v3.dtsi b/arch/arm/boot/dts/imx6q-bx50v3.dtsi
index 10922375c51e..ead83091e193 100644
--- a/arch/arm/boot/dts/imx6q-bx50v3.dtsi
+++ b/arch/arm/boot/dts/imx6q-bx50v3.dtsi
@@ -160,7 +160,7 @@
 	pinctrl-0 = <&pinctrl_ecspi5>;
 	status = "okay";
 
-	m25_eeprom: m25p80@0 {
+	m25_eeprom: flash@0 {
 		compatible = "atmel,at25";
 		spi-max-frequency = <10000000>;
 		size = <0x8000>;
diff --git a/arch/arm/boot/dts/imx6q-cm-fx6.dts b/arch/arm/boot/dts/imx6q-cm-fx6.dts
index bfb530f29d9d..1ad41c944b4b 100644
--- a/arch/arm/boot/dts/imx6q-cm-fx6.dts
+++ b/arch/arm/boot/dts/imx6q-cm-fx6.dts
@@ -260,7 +260,7 @@
 	pinctrl-0 = <&pinctrl_ecspi1>;
 	status = "okay";
 
-	m25p80@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "st,m25p", "jedec,spi-nor";
diff --git a/arch/arm/boot/dts/imx6q-dmo-edmqmx6.dts b/arch/arm/boot/dts/imx6q-dmo-edmqmx6.dts
index c713ac03b3b9..9591848cbd37 100644
--- a/arch/arm/boot/dts/imx6q-dmo-edmqmx6.dts
+++ b/arch/arm/boot/dts/imx6q-dmo-edmqmx6.dts
@@ -102,7 +102,7 @@
 	cs-gpios = <&gpio1 12 GPIO_ACTIVE_LOW>;
 	status = "okay";
 
-	flash: m25p80@0 {
+	flash: flash@0 {
 		compatible = "m25p80", "jedec,spi-nor";
 		spi-max-frequency = <40000000>;
 		reg = <0>;
diff --git a/arch/arm/boot/dts/imx6q-dms-ba16.dts b/arch/arm/boot/dts/imx6q-dms-ba16.dts
index 48fb47e715f6..137db38f0d27 100644
--- a/arch/arm/boot/dts/imx6q-dms-ba16.dts
+++ b/arch/arm/boot/dts/imx6q-dms-ba16.dts
@@ -47,7 +47,7 @@
 	pinctrl-0 = <&pinctrl_ecspi5>;
 	status = "okay";
 
-	m25_eeprom: m25p80@0 {
+	m25_eeprom: flash@0 {
 		compatible = "atmel,at25256B", "atmel,at25";
 		spi-max-frequency = <20000000>;
 		size = <0x8000>;
diff --git a/arch/arm/boot/dts/imx6q-evi.dts b/arch/arm/boot/dts/imx6q-evi.dts
index c63f371ede8b..78d941fef5df 100644
--- a/arch/arm/boot/dts/imx6q-evi.dts
+++ b/arch/arm/boot/dts/imx6q-evi.dts
@@ -146,6 +146,7 @@
 	pinctrl-0 = <&pinctrl_enet>;
 	phy-mode = "rgmii";
 	phy-reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
+	/delete-property/ interrupts;
 	interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
 			      <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
 	fsl,err006687-workaround-present;
diff --git a/arch/arm/boot/dts/imx6q-gk802.dts b/arch/arm/boot/dts/imx6q-gk802.dts
index ccc2487d47ca..2fda68f9d3f6 100644
--- a/arch/arm/boot/dts/imx6q-gk802.dts
+++ b/arch/arm/boot/dts/imx6q-gk802.dts
@@ -1,10 +1,5 @@
-/*
- * Copyright (C) 2013 Philipp Zabel
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2.  This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
- */
+// SPDX-License-Identifier: GPL-2.0-only
+// Copyright (C) 2013 Philipp Zabel
 
 /dts-v1/;
 #include <dt-bindings/gpio/gpio.h>
diff --git a/arch/arm/boot/dts/imx6q-gw5400-a.dts b/arch/arm/boot/dts/imx6q-gw5400-a.dts
index 4cde45d5c90c..e894faba571f 100644
--- a/arch/arm/boot/dts/imx6q-gw5400-a.dts
+++ b/arch/arm/boot/dts/imx6q-gw5400-a.dts
@@ -137,7 +137,7 @@
 	pinctrl-0 = <&pinctrl_ecspi1>;
 	status = "okay";
 
-	flash: m25p80@0 {
+	flash: flash@0 {
 		compatible = "sst,w25q256", "jedec,spi-nor";
 		spi-max-frequency = <30000000>;
 		reg = <0>;
diff --git a/arch/arm/boot/dts/imx6q-marsboard.dts b/arch/arm/boot/dts/imx6q-marsboard.dts
index 05ee28388229..cc1801002394 100644
--- a/arch/arm/boot/dts/imx6q-marsboard.dts
+++ b/arch/arm/boot/dts/imx6q-marsboard.dts
@@ -100,7 +100,7 @@
 	cs-gpios = <&gpio2 30 GPIO_ACTIVE_LOW>;
 	status = "okay";
 
-	m25p80@0 {
+	flash@0 {
 		compatible = "microchip,sst25vf016b";
 		spi-max-frequency = <20000000>;
 		reg = <0>;
diff --git a/arch/arm/boot/dts/imx6q-mba6.dtsi b/arch/arm/boot/dts/imx6q-mba6.dtsi
new file mode 100644
index 000000000000..0d7be4567291
--- /dev/null
+++ b/arch/arm/boot/dts/imx6q-mba6.dtsi
@@ -0,0 +1,44 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright 2013 Sascha Hauer, Pengutronix
+ *
+ * Copyright 2013-2021 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+&ecspi5 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi5_mba6x>;
+	cs-gpios = <&gpio1 17 GPIO_ACTIVE_LOW>;
+};
+
+&ethphy {
+	rxdv-skew-ps = <180>;
+	txen-skew-ps = <120>;
+	rxd3-skew-ps = <180>;
+	rxd2-skew-ps = <180>;
+	rxd1-skew-ps = <180>;
+	rxd0-skew-ps = <180>;
+	txd3-skew-ps = <120>;
+	txd2-skew-ps = <0>;
+	txd1-skew-ps = <180>;
+	txd0-skew-ps = <360>;
+	txc-skew-ps = <1860>;
+	rxc-skew-ps = <1860>;
+};
+
+&sata {
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_ecspi5_mba6x: ecspi5grp-mba6x {
+		fsl,pins = <
+			/* HYS, SPEED = MED, 100k up, DSE = 011, SRE_FAST */
+			MX6QDL_PAD_SD1_DAT0__ECSPI5_MISO 0x1b099
+			MX6QDL_PAD_SD1_CMD__ECSPI5_MOSI 0xb099
+			MX6QDL_PAD_SD1_CLK__ECSPI5_SCLK 0xb099
+			MX6QDL_PAD_SD1_DAT1__GPIO1_IO17 0xb099 /* eCSPI5 SS0 */
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6q-mba6a.dts b/arch/arm/boot/dts/imx6q-mba6a.dts
new file mode 100644
index 000000000000..349a08605a5e
--- /dev/null
+++ b/arch/arm/boot/dts/imx6q-mba6a.dts
@@ -0,0 +1,20 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright 2013 Sascha Hauer, Pengutronix
+ *
+ * Copyright 2013-2021 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+/dts-v1/;
+
+#include "imx6q-tqma6a.dtsi"
+#include "imx6qdl-mba6.dtsi"
+#include "imx6qdl-mba6a.dtsi"
+#include "imx6q-mba6.dtsi"
+
+/ {
+	model = "TQ TQMa6Q on MBa6x";
+	compatible = "tq,imx6q-mba6x-a", "tq,mba6a",
+		     "tq,imx6q-tqma6q-a", "fsl,imx6q";
+};
diff --git a/arch/arm/boot/dts/imx6q-mba6b.dts b/arch/arm/boot/dts/imx6q-mba6b.dts
new file mode 100644
index 000000000000..02c9f3e91b8f
--- /dev/null
+++ b/arch/arm/boot/dts/imx6q-mba6b.dts
@@ -0,0 +1,20 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright 2013 Sascha Hauer, Pengutronix
+ *
+ * Copyright 2013-2021 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+/dts-v1/;
+
+#include "imx6q-tqma6b.dtsi"
+#include "imx6qdl-mba6.dtsi"
+#include "imx6qdl-mba6b.dtsi"
+#include "imx6q-mba6.dtsi"
+
+/ {
+	model = "TQ TQMa6Q on MBa6x";
+	compatible = "tq,imx6q-mba6x-b", "tq,mba6b",
+		     "tq,imx6q-tqma6q-b", "fsl,imx6q";
+};
diff --git a/arch/arm/boot/dts/imx6q-mccmon6.dts b/arch/arm/boot/dts/imx6q-mccmon6.dts
index 55692c73943d..f08b37010291 100644
--- a/arch/arm/boot/dts/imx6q-mccmon6.dts
+++ b/arch/arm/boot/dts/imx6q-mccmon6.dts
@@ -100,8 +100,10 @@
 	pinctrl-0 = <&pinctrl_enet>;
 	phy-mode = "rgmii";
 	phy-reset-gpios = <&gpio1 27 GPIO_ACTIVE_LOW>;
+	/delete-property/ interrupts;
 	interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
 			      <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
+	fsl,err006687-workaround-present;
 	status = "okay";
 };
 
diff --git a/arch/arm/boot/dts/imx6q-novena.dts b/arch/arm/boot/dts/imx6q-novena.dts
index 225cf6b7a7a4..ee8c0bd3ecfd 100644
--- a/arch/arm/boot/dts/imx6q-novena.dts
+++ b/arch/arm/boot/dts/imx6q-novena.dts
@@ -86,7 +86,7 @@
 			linux,code = <KEY_POWER>;
 		};
 
-		lid {
+		lid-event {
 			label = "Lid";
 			gpios = <&gpio4 12 GPIO_ACTIVE_LOW>;
 			linux,input-type = <5>;	/* EV_SW */
@@ -99,7 +99,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_leds_novena>;
 
-		heartbeat {
+		led-heartbeat {
 			label = "novena:white:panel";
 			gpios = <&gpio1 21 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "default-on";
diff --git a/arch/arm/boot/dts/imx6q-phytec-mira-rdk-emmc.dts b/arch/arm/boot/dts/imx6q-phytec-mira-rdk-emmc.dts
index 2e70ea5623c6..322f071d972f 100644
--- a/arch/arm/boot/dts/imx6q-phytec-mira-rdk-emmc.dts
+++ b/arch/arm/boot/dts/imx6q-phytec-mira-rdk-emmc.dts
@@ -8,6 +8,9 @@
 #include "imx6q.dtsi"
 #include "imx6qdl-phytec-phycore-som.dtsi"
 #include "imx6qdl-phytec-mira.dtsi"
+#include "imx6qdl-phytec-mira-peb-eval-01.dtsi"
+#include "imx6qdl-phytec-mira-peb-av-02.dtsi"
+#include "imx6qdl-phytec-mira-peb-wlbt-05.dtsi"
 
 / {
 	model = "PHYTEC phyBOARD-Mira Quad Carrier-Board with eMMC";
diff --git a/arch/arm/boot/dts/imx6q-phytec-mira-rdk-nand.dts b/arch/arm/boot/dts/imx6q-phytec-mira-rdk-nand.dts
index 65d2e483c136..3f13726c8058 100644
--- a/arch/arm/boot/dts/imx6q-phytec-mira-rdk-nand.dts
+++ b/arch/arm/boot/dts/imx6q-phytec-mira-rdk-nand.dts
@@ -8,6 +8,9 @@
 #include "imx6q.dtsi"
 #include "imx6qdl-phytec-phycore-som.dtsi"
 #include "imx6qdl-phytec-mira.dtsi"
+#include "imx6qdl-phytec-mira-peb-eval-01.dtsi"
+#include "imx6qdl-phytec-mira-peb-av-02.dtsi"
+#include "imx6qdl-phytec-mira-peb-wlbt-05.dtsi"
 
 / {
 	model = "PHYTEC phyBOARD-Mira Quad Carrier-Board with NAND";
diff --git a/arch/arm/boot/dts/imx6q-pistachio.dts b/arch/arm/boot/dts/imx6q-pistachio.dts
index 7a33e54cc0f1..bad8d831e64e 100644
--- a/arch/arm/boot/dts/imx6q-pistachio.dts
+++ b/arch/arm/boot/dts/imx6q-pistachio.dts
@@ -100,7 +100,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gpio_keys>;
 
-		power {
+		key-power {
 			label = "Power Button";
 			gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
 			wakeup-source;
diff --git a/arch/arm/boot/dts/imx6q-rex-pro.dts b/arch/arm/boot/dts/imx6q-rex-pro.dts
index 1767e1a3cd53..271f4b2d9b9f 100644
--- a/arch/arm/boot/dts/imx6q-rex-pro.dts
+++ b/arch/arm/boot/dts/imx6q-rex-pro.dts
@@ -19,7 +19,7 @@
 };
 
 &ecspi3 {
-	flash: m25p80@0 {
+	flash: flash@0 {
 		compatible = "sst,sst25vf032b", "jedec,spi-nor";
 		spi-max-frequency = <20000000>;
 		reg = <0>;
diff --git a/arch/arm/boot/dts/imx6q-sabrelite.dts b/arch/arm/boot/dts/imx6q-sabrelite.dts
index dc51262e7b2f..7c6a2f234ccb 100644
--- a/arch/arm/boot/dts/imx6q-sabrelite.dts
+++ b/arch/arm/boot/dts/imx6q-sabrelite.dts
@@ -1,43 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0 OR X11
 /*
  * Copyright 2011 Freescale Semiconductor, Inc.
  * Copyright 2011 Linaro Ltd.
  *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License
- *     version 2 as published by the Free Software Foundation.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
  */
 
 /dts-v1/;
diff --git a/arch/arm/boot/dts/imx6q-skov-reve-mi1010ait-1cp1.dts b/arch/arm/boot/dts/imx6q-skov-reve-mi1010ait-1cp1.dts
index 7f1f19b74bfa..a3f247c722b4 100644
--- a/arch/arm/boot/dts/imx6q-skov-reve-mi1010ait-1cp1.dts
+++ b/arch/arm/boot/dts/imx6q-skov-reve-mi1010ait-1cp1.dts
@@ -125,3 +125,9 @@
 		>;
 	};
 };
+
+&reg_tft_vcom {
+	regulator-min-microvolt = <3160000>;
+	regulator-max-microvolt = <3160000>;
+	voltage-table = <3160000 73>;
+};
diff --git a/arch/arm/boot/dts/imx6q-tbs2910.dts b/arch/arm/boot/dts/imx6q-tbs2910.dts
index 343364d3e4f7..8daef65d5bb3 100644
--- a/arch/arm/boot/dts/imx6q-tbs2910.dts
+++ b/arch/arm/boot/dts/imx6q-tbs2910.dts
@@ -159,7 +159,7 @@
 	pinctrl-0 = <&pinctrl_i2c3>;
 	status = "okay";
 
-	rtc: ds1307@68 {
+	rtc: rtc@68 {
 		compatible = "dallas,ds1307";
 		reg = <0x68>;
 	};
diff --git a/arch/arm/boot/dts/imx6q-utilite-pro.dts b/arch/arm/boot/dts/imx6q-utilite-pro.dts
index d16ff2083d62..ad59b23ef27a 100644
--- a/arch/arm/boot/dts/imx6q-utilite-pro.dts
+++ b/arch/arm/boot/dts/imx6q-utilite-pro.dts
@@ -89,7 +89,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gpio_keys>;
 
-		power {
+		key-power {
 			label = "Power Button";
 			gpios = <&gpio1 29 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
diff --git a/arch/arm/boot/dts/imx6q-var-dt6customboard.dts b/arch/arm/boot/dts/imx6q-var-dt6customboard.dts
index 63550351340d..2290c1237634 100644
--- a/arch/arm/boot/dts/imx6q-var-dt6customboard.dts
+++ b/arch/arm/boot/dts/imx6q-var-dt6customboard.dts
@@ -28,7 +28,7 @@
 		compatible = "gpio-keys";
 		autorepeat;
 
-		back {
+		key-back {
 			gpios = <&gpio4 26 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_BACK>;
 			label = "Key Back";
@@ -37,7 +37,7 @@
 			wakeup-source;
 		};
 
-		home {
+		key-home {
 			gpios = <&gpio5 11 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_HOME>;
 			label = "Key Home";
@@ -46,7 +46,7 @@
 			wakeup-source;
 		};
 
-		menu {
+		key-menu {
 			gpios = <&gpio4 25 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_MENU>;
 			label = "Key Menu";
diff --git a/arch/arm/boot/dts/imx6q-vicut1.dts b/arch/arm/boot/dts/imx6q-vicut1.dts
index 0a4e251be162..dd91aff3f9e2 100644
--- a/arch/arm/boot/dts/imx6q-vicut1.dts
+++ b/arch/arm/boot/dts/imx6q-vicut1.dts
@@ -6,12 +6,9 @@
 /dts-v1/;
 #include "imx6q.dtsi"
 #include "imx6qdl-vicut1.dtsi"
+#include "imx6qdl-vicut1-12inch.dtsi"
 
 / {
 	model = "Kverneland UT1Q Board";
 	compatible = "kvg,vicut1q", "fsl,imx6q";
 };
-
-&sata {
-	status = "okay";
-};
diff --git a/arch/arm/boot/dts/imx6q-yapp4-crux.dts b/arch/arm/boot/dts/imx6q-yapp4-crux.dts
new file mode 100644
index 000000000000..bddf3822ebf7
--- /dev/null
+++ b/arch/arm/boot/dts/imx6q-yapp4-crux.dts
@@ -0,0 +1,58 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// Copyright (C) 2021 Y Soft Corporation, a.s.
+
+/dts-v1/;
+
+#include "imx6q.dtsi"
+#include "imx6dl-yapp4-common.dtsi"
+
+/ {
+	model = "Y Soft IOTA Crux i.MX6Quad board";
+	compatible = "ysoft,imx6q-yapp4-crux", "fsl,imx6q";
+
+	memory@10000000 {
+		device_type = "memory";
+		reg = <0x10000000 0xf0000000>;
+	};
+};
+
+&gpio_oled {
+	status = "okay";
+};
+
+&leds {
+	status = "okay";
+};
+
+&oled_1305 {
+	status = "okay";
+};
+
+&oled_1309 {
+	status = "okay";
+};
+
+&reg_pu {
+	regulator-always-on;
+};
+
+&reg_usb_h1_vbus {
+	status = "okay";
+};
+
+&touchkeys {
+	status = "okay";
+};
+
+&uart2 {
+	status = "disabled";
+};
+
+&usbh1 {
+	status = "okay";
+};
+
+&usbphy2 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6q.dtsi b/arch/arm/boot/dts/imx6q.dtsi
index 9caba4529c71..df86049a695b 100644
--- a/arch/arm/boot/dts/imx6q.dtsi
+++ b/arch/arm/boot/dts/imx6q.dtsi
@@ -159,14 +159,17 @@
 		};
 	};
 
-	soc {
+	soc: soc {
 		ocram: sram@900000 {
 			compatible = "mmio-sram";
 			reg = <0x00900000 0x40000>;
+			ranges = <0 0x00900000 0x40000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 			clocks = <&clks IMX6QDL_CLK_OCRAM>;
 		};
 
-		bus@2000000 { /* AIPS1 */
+		aips1: bus@2000000 { /* AIPS1 */
 			spba-bus@2000000 {
 				ecspi5: spi@2018000 {
 					#address-cells = <1>;
diff --git a/arch/arm/boot/dts/imx6qdl-apalis.dtsi b/arch/arm/boot/dts/imx6qdl-apalis.dtsi
index ed2739e39085..7c17b91f0965 100644
--- a/arch/arm/boot/dts/imx6qdl-apalis.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-apalis.dtsi
@@ -1,11 +1,12 @@
-// SPDX-License-Identifier: GPL-2.0+ OR MIT
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
 /*
- * Copyright 2014-2020 Toradex
+ * Copyright 2014-2022 Toradex
  * Copyright 2012 Freescale Semiconductor, Inc.
  * Copyright 2011 Linaro Ltd.
  */
 
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pwm/pwm.h>
 
 / {
 	model = "Toradex Apalis iMX6Q/D Module";
@@ -19,88 +20,182 @@
 
 	backlight: backlight {
 		compatible = "pwm-backlight";
+		brightness-levels = <0 45 63 88 119 158 203 255>;
+		default-brightness-level = <4>;
+		enable-gpios = <&gpio3 13 GPIO_ACTIVE_HIGH>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gpio_bl_on>;
-		pwms = <&pwm4 0 5000000>;
-		enable-gpios = <&gpio3 13 GPIO_ACTIVE_HIGH>;
+		power-supply = <&reg_module_3v3>;
+		pwms = <&pwm4 0 5000000 PWM_POLARITY_INVERTED>;
+		status = "disabled";
+	};
+
+	clk_ov5640_osc: clk-ov5640-osc {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <24000000>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_keys>;
+
+		wakeup {
+			debounce-interval = <10>;
+			gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
+			label = "Wake-Up";
+			linux,code = <KEY_WAKEUP>;
+			wakeup-source;
+		};
+	};
+
+	lcd_display: disp0 {
+		compatible = "fsl,imx-parallel-display";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		interface-pix-fmt = "rgb24";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ipu1_lcdif>;
+		status = "disabled";
+
+		port@0 {
+			reg = <0>;
+
+			lcd_display_in: endpoint {
+				remote-endpoint = <&ipu1_di1_disp1>;
+			};
+		};
+
+		port@1 {
+			reg = <1>;
+
+			lcd_display_out: endpoint {
+				remote-endpoint = <&lcd_panel_in>;
+			};
+		};
+	};
+
+	panel_dpi: panel-dpi {
+		compatible = "edt,et057090dhu";
+		backlight = <&backlight>;
+
+		status = "disabled";
+
+		port {
+			lcd_panel_in: endpoint {
+				remote-endpoint = <&lcd_display_out>;
+			};
+		};
+	};
+
+	panel_lvds: panel-lvds {
+		compatible = "panel-lvds";
+		backlight = <&backlight>;
 		status = "disabled";
+
+		port {
+			lvds_panel_in: endpoint {
+				remote-endpoint = <&lvds0_out>;
+			};
+		};
 	};
 
 	reg_module_3v3: regulator-module-3v3 {
 		compatible = "regulator-fixed";
-		regulator-name = "+V3.3";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
 		regulator-always-on;
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "+V3.3";
 	};
 
 	reg_module_3v3_audio: regulator-module-3v3-audio {
 		compatible = "regulator-fixed";
-		regulator-name = "+V3.3_AUDIO";
-		regulator-min-microvolt = <3300000>;
+		regulator-always-on;
 		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "+V3.3_AUDIO";
+	};
+
+	reg_ov5640_1v8_d_o_vdd: regulator-ov5640-1v8-d-o-vdd {
+		compatible = "regulator-fixed";
 		regulator-always-on;
+		regulator-max-microvolt = <1800000>;
+		regulator-min-microvolt = <1800000>;
+		regulator-name = "DOVDD/DVDD_1.8V";
+		/* Note: The CSI module uses on-board 3.3V_SW supply */
+		vin-supply = <&reg_module_3v3>;
+	};
+
+	reg_ov5640_2v8_a_vdd: regulator-ov5640-2v8-a-vdd {
+		compatible = "regulator-fixed";
+		regulator-always-on;
+		regulator-max-microvolt = <2800000>;
+		regulator-min-microvolt = <2800000>;
+		regulator-name = "AVDD/AFVDD_2.8V";
+		/* Note: The CSI module uses on-board 3.3V_SW supply */
+		vin-supply = <&reg_module_3v3>;
 	};
 
 	reg_usb_otg_vbus: regulator-usb-otg-vbus {
 		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_regulator_usbotg_pwr>;
-		regulator-name = "usb_otg_vbus";
-		regulator-min-microvolt = <5000000>;
 		regulator-max-microvolt = <5000000>;
-		gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
+		regulator-min-microvolt = <5000000>;
+		regulator-name = "usb_otg_vbus";
 		status = "disabled";
 	};
 
 	/* on module USB hub */
 	reg_usb_host_vbus_hub: regulator-usb-host-vbus-hub {
 		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio3 28 GPIO_ACTIVE_HIGH>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_regulator_usbhub_pwr>;
-		regulator-name = "usb_host_vbus_hub";
-		regulator-min-microvolt = <5000000>;
 		regulator-max-microvolt = <5000000>;
-		gpio = <&gpio3 28 GPIO_ACTIVE_HIGH>;
+		regulator-min-microvolt = <5000000>;
+		regulator-name = "usb_host_vbus_hub";
 		startup-delay-us = <2000>;
-		enable-active-high;
 		status = "okay";
 	};
 
 	reg_usb_host_vbus: regulator-usb-host-vbus {
 		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio =  <&gpio1 0 GPIO_ACTIVE_HIGH>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_regulator_usbh_pwr>;
-		regulator-name = "usb_host_vbus";
-		regulator-min-microvolt = <5000000>;
 		regulator-max-microvolt = <5000000>;
-		gpio =  <&gpio1 0 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
+		regulator-min-microvolt = <5000000>;
+		regulator-name = "usb_host_vbus";
 		vin-supply = <&reg_usb_host_vbus_hub>;
 		status = "disabled";
 	};
 
 	sound {
 		compatible = "fsl,imx-audio-sgtl5000";
-		model = "imx6q-apalis-sgtl5000";
-		ssi-controller = <&ssi1>;
 		audio-codec = <&codec>;
 		audio-routing =
 			"LINE_IN", "Line In Jack",
 			"MIC_IN", "Mic Jack",
 			"Mic Jack", "Mic Bias",
 			"Headphone Jack", "HP_OUT";
-		mux-int-port = <1>;
+		model = "imx6q-apalis-sgtl5000";
 		mux-ext-port = <4>;
+		mux-int-port = <1>;
+		ssi-controller = <&ssi1>;
 	};
 
 	sound_spdif: sound-spdif {
 		compatible = "fsl,imx-audio-spdif";
-		model = "imx-spdif";
 		spdif-controller = <&spdif>;
 		spdif-in;
 		spdif-out;
+		model = "imx-spdif";
 		status = "disabled";
 	};
 };
@@ -125,6 +220,10 @@
 	status = "disabled";
 };
 
+&clks {
+	fsl,pmic-stby-poweroff;
+};
+
 /* Apalis SPI1 */
 &ecspi1 {
 	cs-gpios = <&gpio5 25 GPIO_ACTIVE_LOW>;
@@ -141,6 +240,214 @@
 	status = "disabled";
 };
 
+&gpio1 {
+	gpio-line-names = "MXM3_84",
+			  "MXM3_4",
+			  "MXM3_15/GPIO7",
+			  "MXM3_96",
+			  "MXM3_37",
+			  "",
+			  "MXM3_17/GPIO8",
+			  "MXM3_14",
+			  "MXM3_12",
+			  "MXM3_2",
+			  "MXM3_184",
+			  "MXM3_180",
+			  "MXM3_178",
+			  "MXM3_176",
+			  "MXM3_188",
+			  "MXM3_186",
+			  "MXM3_160",
+			  "MXM3_162",
+			  "MXM3_150",
+			  "MXM3_144",
+			  "MXM3_154",
+			  "MXM3_146",
+			  "",
+			  "",
+			  "MXM3_72";
+};
+
+&gpio2 {
+	gpio-line-names = "MXM3_148",
+			  "MXM3_152",
+			  "MXM3_156",
+			  "MXM3_158",
+			  "MXM3_1/GPIO1",
+			  "MXM3_3/GPIO2",
+			  "MXM3_5/GPIO3",
+			  "MXM3_7/GPIO4",
+			  "MXM3_95",
+			  "MXM3_6",
+			  "MXM3_8",
+			  "MXM3_123",
+			  "MXM3_126",
+			  "MXM3_128",
+			  "MXM3_130",
+			  "MXM3_132",
+			  "MXM3_253",
+			  "MXM3_251",
+			  "MXM3_283",
+			  "MXM3_281",
+			  "MXM3_279",
+			  "MXM3_277",
+			  "MXM3_243",
+			  "MXM3_235",
+			  "MXM3_231",
+			  "MXM3_229",
+			  "MXM3_233",
+			  "MXM3_198",
+			  "MXM3_275",
+			  "MXM3_273",
+			  "MXM3_207",
+			  "MXM3_122";
+};
+
+&gpio3 {
+	gpio-line-names = "MXM3_271",
+			  "MXM3_269",
+			  "MXM3_301",
+			  "MXM3_299",
+			  "MXM3_297",
+			  "MXM3_295",
+			  "MXM3_293",
+			  "MXM3_291",
+			  "MXM3_289",
+			  "MXM3_287",
+			  "MXM3_249",
+			  "MXM3_247",
+			  "MXM3_245",
+			  "MXM3_286",
+			  "MXM3_239",
+			  "MXM3_35",
+			  "MXM3_205",
+			  "MXM3_203",
+			  "MXM3_201",
+			  "MXM3_116",
+			  "MXM3_114",
+			  "MXM3_262",
+			  "MXM3_274",
+			  "MXM3_124",
+			  "MXM3_110",
+			  "MXM3_120",
+			  "MXM3_263",
+			  "MXM3_265",
+			  "",
+			  "MXM3_135",
+			  "MXM3_261",
+			  "MXM3_259";
+};
+
+&gpio4 {
+	gpio-line-names = "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "MXM3_194",
+			  "MXM3_136",
+			  "MXM3_134",
+			  "MXM3_140",
+			  "MXM3_138",
+			  "",
+			  "MXM3_220",
+			  "",
+			  "",
+			  "MXM3_18",
+			  "MXM3_16",
+			  "",
+			  "",
+			  "MXM3_214",
+			  "MXM3_216",
+			  "MXM3_164";
+};
+
+&gpio5 {
+	gpio-line-names = "MXM3_159",
+			  "",
+			  "",
+			  "",
+			  "MXM3_257",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "MXM3_200",
+			  "MXM3_196",
+			  "MXM3_204",
+			  "MXM3_202",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "MXM3_191",
+			  "MXM3_197",
+			  "MXM3_77",
+			  "MXM3_195",
+			  "MXM3_221",
+			  "MXM3_225",
+			  "MXM3_223",
+			  "MXM3_227",
+			  "MXM3_209",
+			  "MXM3_211",
+			  "MXM3_118",
+			  "MXM3_112",
+			  "MXM3_187",
+			  "MXM3_185";
+};
+
+&gpio6 {
+	gpio-line-names = "MXM3_183",
+			  "MXM3_181",
+			  "MXM3_179",
+			  "MXM3_177",
+			  "MXM3_175",
+			  "MXM3_173",
+			  "MXM3_255",
+			  "MXM3_83",
+			  "MXM3_91",
+			  "MXM3_13/GPIO6",
+			  "MXM3_11/GPIO5",
+			  "MXM3_79",
+			  "",
+			  "",
+			  "MXM3_190",
+			  "MXM3_193",
+			  "MXM3_89";
+};
+
+&gpio7 {
+	gpio-line-names = "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "MXM3_99",
+			  "MXM3_85",
+			  "MXM3_217",
+			  "MXM3_215";
+};
+
+&gpr {
+	ipu1_csi0_mux {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "disabled";
+
+		port@1 {
+			reg = <1>;
+			ipu1_csi0_mux_from_parallel_sensor: endpoint {
+				remote-endpoint = <&adv7280_to_ipu1_csi0_mux>;
+			};
+		};
+	};
+};
+
 &fec {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
@@ -177,6 +484,16 @@
 	scl-gpios = <&gpio5 27 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 	sda-gpios = <&gpio5 26 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 	status = "disabled";
+
+	atmel_mxt_ts: touchscreen@4a {
+		compatible = "atmel,maxtouch";
+		/* These GPIOs are muxed with the iomuxc node */
+		interrupt-parent = <&gpio6>;
+		interrupts = <10 IRQ_TYPE_EDGE_FALLING>;	/* MXM3_11 */
+		reg = <0x4a>;
+		reset-gpios = <&gpio6 9 GPIO_ACTIVE_LOW>;	/* MXM3_13 */
+		status = "disabled";
+	};
 };
 
 /*
@@ -192,101 +509,105 @@
 	sda-gpios = <&gpio4 13 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 	status = "okay";
 
-	pmic: pfuze100@8 {
+	pmic: pmic@8 {
 		compatible = "fsl,pfuze100";
+		fsl,pmic-stby-poweroff;
 		reg = <0x08>;
 
 		regulators {
 			sw1a_reg: sw1ab {
-				regulator-min-microvolt = <300000>;
-				regulator-max-microvolt = <1875000>;
-				regulator-boot-on;
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1875000>;
+				regulator-min-microvolt = <300000>;
 				regulator-ramp-delay = <6250>;
 			};
 
 			sw1c_reg: sw1c {
-				regulator-min-microvolt = <300000>;
-				regulator-max-microvolt = <1875000>;
-				regulator-boot-on;
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1875000>;
+				regulator-min-microvolt = <300000>;
 				regulator-ramp-delay = <6250>;
 			};
 
 			sw3a_reg: sw3a {
-				regulator-min-microvolt = <400000>;
-				regulator-max-microvolt = <1975000>;
-				regulator-boot-on;
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1975000>;
+				regulator-min-microvolt = <400000>;
 			};
 
 			swbst_reg: swbst {
-				regulator-min-microvolt = <5000000>;
-				regulator-max-microvolt = <5150000>;
-				regulator-boot-on;
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <5150000>;
+				regulator-min-microvolt = <5000000>;
 			};
 
 			snvs_reg: vsnvs {
-				regulator-min-microvolt = <1000000>;
-				regulator-max-microvolt = <3000000>;
-				regulator-boot-on;
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <3000000>;
+				regulator-min-microvolt = <1000000>;
 			};
 
 			vref_reg: vrefddr {
-				regulator-boot-on;
 				regulator-always-on;
+				regulator-boot-on;
 			};
 
 			vgen1_reg: vgen1 {
-				regulator-min-microvolt = <800000>;
-				regulator-max-microvolt = <1550000>;
-				regulator-boot-on;
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1550000>;
+				regulator-min-microvolt = <800000>;
 			};
 
 			vgen2_reg: vgen2 {
-				regulator-min-microvolt = <800000>;
-				regulator-max-microvolt = <1550000>;
-				regulator-boot-on;
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1550000>;
+				regulator-min-microvolt = <800000>;
 			};
 
 			vgen3_reg: vgen3 {
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <3300000>;
-				regulator-boot-on;
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <3300000>;
+				regulator-min-microvolt = <1800000>;
 			};
 
 			vgen4_reg: vgen4 {
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <1800000>;
-				regulator-boot-on;
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1800000>;
+				regulator-min-microvolt = <1800000>;
 			};
 
 			vgen5_reg: vgen5 {
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <3300000>;
-				regulator-boot-on;
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <3300000>;
+				regulator-min-microvolt = <1800000>;
 			};
 
 			vgen6_reg: vgen6 {
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <3300000>;
-				regulator-boot-on;
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <3300000>;
+				regulator-min-microvolt = <1800000>;
 			};
 		};
 	};
 
 	codec: sgtl5000@a {
 		compatible = "fsl,sgtl5000";
-		reg = <0x0a>;
+		#sound-dai-cells = <0>;
 		clocks = <&clks IMX6QDL_CLK_CKO>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_sgtl5000>;
+		reg = <0x0a>;
 		VDDA-supply = <&reg_module_3v3_audio>;
 		VDDIO-supply = <&reg_module_3v3>;
 		VDDD-supply = <&vgen4_reg>;
@@ -295,15 +616,15 @@
 	/* STMPE811 touch screen controller */
 	stmpe811@41 {
 		compatible = "st,stmpe811";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_touch_int>;
-		reg = <0x41>;
+		blocks = <0x5>;
+		id = <0>;
 		interrupts = <10 IRQ_TYPE_LEVEL_LOW>;
-		interrupt-parent = <&gpio4>;
 		interrupt-controller;
-		id = <0>;
-		blocks = <0x5>;
+		interrupt-parent = <&gpio4>;
 		irq-trigger = <0x1>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_touch_int>;
+		reg = <0x41>;
 		/* 3.25 MHz ADC clock speed */
 		st,adc-freq = <1>;
 		/* 12-bit ADC */
@@ -313,7 +634,7 @@
 		/* ADC conversion time: 80 clocks */
 		st,sample-time = <4>;
 
-		stmpe_touchscreen: stmpe-touchscreen {
+		stmpe_ts: stmpe_touchscreen {
 			compatible = "st,stmpe-ts";
 			/* 8 sample average control */
 			st,ave-ctrl = <3>;
@@ -328,13 +649,14 @@
 			st,settling = <3>;
 			/* 5 ms touch detect interrupt delay */
 			st,touch-det-delay = <5>;
+			status = "disabled";
 		};
 
-		stmpe_adc: stmpe-adc {
+		stmpe_adc: stmpe_adc {
 			compatible = "st,stmpe-adc";
+			#io-channel-cells = <1>;
 			/* forbid to use ADC channels 3-0 (touch) */
 			st,norequest-mask = <0x0F>;
-			#io-channel-cells = <1>;
 		};
 	};
 };
@@ -351,6 +673,90 @@
 	scl-gpios = <&gpio3 17 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 	sda-gpios = <&gpio3 18 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 	status = "disabled";
+
+	adv_7280: adv7280@21 {
+		compatible = "adi,adv7280";
+		adv,force-bt656-4;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ipu1_csi0>;
+		reg = <0x21>;
+		status = "disabled";
+
+		port {
+			adv7280_to_ipu1_csi0_mux: endpoint {
+				bus-width = <8>;
+				remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>;
+			};
+		};
+	};
+
+	ov5640_csi_cam: ov5640_mipi@3c {
+		compatible = "ovti,ov5640";
+		AVDD-supply = <&reg_ov5640_2v8_a_vdd>;
+		DOVDD-supply = <&reg_ov5640_1v8_d_o_vdd>;
+		DVDD-supply = <&reg_ov5640_1v8_d_o_vdd>;
+		clock-names = "xclk";
+		clocks = <&clks IMX6QDL_CLK_CKO2>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_cam_mclk>;
+		/* These GPIOs are muxed with the iomuxc node */
+		powerdown-gpios = <&gpio2 5 GPIO_ACTIVE_HIGH>;
+		reg = <0x3c>;
+		reset-gpios = <&gpio2 4 GPIO_ACTIVE_LOW>;
+		status = "disabled";
+
+		port {
+			ov5640_to_mipi_csi2: endpoint {
+				clock-lanes = <0>;
+				data-lanes = <1 2>;
+				remote-endpoint = <&mipi_csi_from_ov5640>;
+			};
+		};
+	};
+};
+
+&ipu1_di1_disp1 {
+	remote-endpoint = <&lcd_display_in>;
+};
+
+&ldb {
+	lvds-channel@0 {
+		port@4 {
+			reg = <4>;
+
+			lvds0_out: endpoint {
+				remote-endpoint = <&lvds_panel_in>;
+			};
+		};
+	};
+
+	lvds-channel@1 {
+		fsl,data-mapping = "spwg";
+		fsl,data-width = <18>;
+
+		port@4 {
+			reg = <4>;
+
+			lvds1_out: endpoint {
+			};
+		};
+	};
+};
+
+&mipi_csi {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "disabled";
+
+	port@0 {
+		reg = <0>;
+
+		mipi_csi_from_ov5640: endpoint {
+			clock-lanes = <0>;
+			data-lanes = <1 2>;
+			remote-endpoint = <&ov5640_to_mipi_csi2>;
+		};
+	};
 };
 
 &pwm1 {
@@ -372,7 +778,6 @@
 };
 
 &pwm4 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm4>;
 	status = "disabled";
@@ -389,72 +794,73 @@
 };
 
 &uart1 {
+	fsl,dte-mode;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart1_dte &pinctrl_uart1_ctrl>;
-	fsl,dte-mode;
 	uart-has-rtscts;
 	status = "disabled";
 };
 
 &uart2 {
+	fsl,dte-mode;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart2_dte>;
-	fsl,dte-mode;
 	uart-has-rtscts;
 	status = "disabled";
 };
 
 &uart4 {
+	fsl,dte-mode;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart4_dte>;
-	fsl,dte-mode;
 	status = "disabled";
 };
 
 &uart5 {
+	fsl,dte-mode;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart5_dte>;
-	fsl,dte-mode;
 	status = "disabled";
 };
 
 &usbotg {
+	disable-over-current;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usbotg>;
-	disable-over-current;
 	status = "disabled";
 };
 
 /* MMC1 */
 &usdhc1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc1_4bit &pinctrl_usdhc1_8bit>;
-	vqmmc-supply = <&reg_module_3v3>;
 	bus-width = <8>;
+	cd-gpios = <&gpio4 20 GPIO_ACTIVE_LOW>;
 	disable-wp;
 	no-1-8-v;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc1_4bit &pinctrl_usdhc1_8bit &pinctrl_mmc_cd>;
+	vqmmc-supply = <&reg_module_3v3>;
 	status = "disabled";
 };
 
 /* SD1 */
 &usdhc2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc2>;
-	vqmmc-supply = <&reg_module_3v3>;
 	bus-width = <4>;
 	disable-wp;
 	no-1-8-v;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	vqmmc-supply = <&reg_module_3v3>;
 	status = "disabled";
 };
 
 /* eMMC */
 &usdhc3 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc3>;
-	vqmmc-supply = <&reg_module_3v3>;
 	bus-width = <8>;
 	no-1-8-v;
 	non-removable;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	vqmmc-supply = <&reg_module_3v3>;
 	status = "okay";
 };
 
@@ -463,49 +869,57 @@
 };
 
 &iomuxc {
-	pinctrl_apalis_gpio1: gpio2io04grp {
+	/* Mux the Apalis GPIOs */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_apalis_gpio1 &pinctrl_apalis_gpio2
+		     &pinctrl_apalis_gpio3 &pinctrl_apalis_gpio4
+		     &pinctrl_apalis_gpio5 &pinctrl_apalis_gpio6
+		     &pinctrl_apalis_gpio7 &pinctrl_apalis_gpio8
+		    >;
+
+	pinctrl_apalis_gpio1: apalisgpio1grp {
 		fsl,pins = <
 			MX6QDL_PAD_NANDF_D4__GPIO2_IO04 0x130b0
 		>;
 	};
 
-	pinctrl_apalis_gpio2: gpio2io05grp {
+	pinctrl_apalis_gpio2: apalisgpio2grp {
 		fsl,pins = <
 			MX6QDL_PAD_NANDF_D5__GPIO2_IO05 0x130b0
 		>;
 	};
 
-	pinctrl_apalis_gpio3: gpio2io06grp {
+	pinctrl_apalis_gpio3: apalisgpio3grp {
 		fsl,pins = <
 			MX6QDL_PAD_NANDF_D6__GPIO2_IO06 0x130b0
 		>;
 	};
 
-	pinctrl_apalis_gpio4: gpio2io07grp {
+	pinctrl_apalis_gpio4: apalisgpio4grp {
 		fsl,pins = <
 			MX6QDL_PAD_NANDF_D7__GPIO2_IO07 0x130b0
 		>;
 	};
 
-	pinctrl_apalis_gpio5: gpio6io10grp {
+	pinctrl_apalis_gpio5: apalisgpio5grp {
 		fsl,pins = <
 			MX6QDL_PAD_NANDF_RB0__GPIO6_IO10 0x130b0
 		>;
 	};
 
-	pinctrl_apalis_gpio6: gpio6io09grp {
+	pinctrl_apalis_gpio6: apalisgpio6grp {
 		fsl,pins = <
 			MX6QDL_PAD_NANDF_WP_B__GPIO6_IO09 0x130b0
 		>;
 	};
 
-	pinctrl_apalis_gpio7: gpio1io02grp {
+	pinctrl_apalis_gpio7: apalisgpio7grp {
 		fsl,pins = <
 			MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x130b0
 		>;
 	};
 
-	pinctrl_apalis_gpio8: gpio1io06grp {
+	pinctrl_apalis_gpio8: apalisgpio8grp {
 		fsl,pins = <
 			MX6QDL_PAD_GPIO_6__GPIO1_IO06 0x130b0
 		>;
@@ -517,8 +931,6 @@
 			MX6QDL_PAD_DISP0_DAT21__AUD4_TXD	0x130b0
 			MX6QDL_PAD_DISP0_DAT22__AUD4_TXFS	0x130b0
 			MX6QDL_PAD_DISP0_DAT23__AUD4_RXD	0x130b0
-			/* SGTL5000 sys_mclk */
-			MX6QDL_PAD_GPIO_5__CCM_CLKO1		0x130b0
 		>;
 	};
 
@@ -600,7 +1012,7 @@
 		>;
 	};
 
-	pinctrl_gpio_bl_on: gpioblon {
+	pinctrl_gpio_bl_on: gpioblongrp {
 		fsl,pins = <
 			MX6QDL_PAD_EIM_DA13__GPIO3_IO13 0x1b0b0
 		>;
@@ -745,7 +1157,7 @@
 		>;
 	};
 
-	pinctrl_mmc_cd: gpiommccdgrp {
+	pinctrl_mmc_cd: mmccdgrp {
 		fsl,pins = <
 			 /* MMC1 CD */
 			MX6QDL_PAD_DI0_PIN4__GPIO4_IO20 0x000b0
@@ -776,41 +1188,47 @@
 		>;
 	};
 
-	pinctrl_regulator_usbh_pwr: gpioregusbhpwrgrp {
+	pinctrl_regulator_usbh_pwr: regusbhpwrgrp {
 		fsl,pins = <
 			/* USBH_EN */
 			MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x0f058
 		>;
 	};
 
-	pinctrl_regulator_usbhub_pwr: gpioregusbhubpwrgrp {
+	pinctrl_regulator_usbhub_pwr: regusbhubpwrgrp {
 		fsl,pins = <
 			/* USBH_HUB_EN */
 			MX6QDL_PAD_EIM_D28__GPIO3_IO28 0x0f058
 		>;
 	};
 
-	pinctrl_regulator_usbotg_pwr: gpioregusbotgpwrgrp {
+	pinctrl_regulator_usbotg_pwr: regusbotgpwrgrp {
 		fsl,pins = <
 			/* USBO1 power en */
 			MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x0f058
 		>;
 	};
 
-	pinctrl_reset_moci: gpioresetmocigrp {
+	pinctrl_reset_moci: resetmocigrp {
 		fsl,pins = <
 			/* RESET_MOCI control */
 			MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x0f058
 		>;
 	};
 
-	pinctrl_sd_cd: gpiosdcdgrp {
+	pinctrl_sd_cd: sdcdgrp {
 		fsl,pins = <
 			/* SD1 CD */
 			MX6QDL_PAD_NANDF_CS1__GPIO6_IO14 0x000b0
 		>;
 	};
 
+	pinctrl_sgtl5000: sgtl5000grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_5__CCM_CLKO1	0x130b0
+		>;
+	};
+
 	pinctrl_spdif: spdifgrp {
 		fsl,pins = <
 			MX6QDL_PAD_GPIO_16__SPDIF_IN  0x1b0b0
@@ -818,13 +1236,22 @@
 		>;
 	};
 
-	pinctrl_touch_int: gpiotouchintgrp {
+	pinctrl_touch_int: touchintgrp {
 		fsl,pins = <
 			/* STMPE811 interrupt */
 			MX6QDL_PAD_KEY_COL2__GPIO4_IO10 0x1b0b0
 		>;
 	};
 
+	/* Additional DTR, DSR, DCD */
+	pinctrl_uart1_ctrl: uart1ctrlgrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D23__UART1_DCD_B 0x1b0b0
+			MX6QDL_PAD_EIM_D24__UART1_DTR_B 0x1b0b0
+			MX6QDL_PAD_EIM_D25__UART1_DSR_B 0x1b0b0
+		>;
+	};
+
 	pinctrl_uart1_dce: uart1dcegrp {
 		fsl,pins = <
 			MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA 0x1b0b1
@@ -842,15 +1269,6 @@
 		>;
 	};
 
-	/* Additional DTR, DSR, DCD */
-	pinctrl_uart1_ctrl: uart1ctrlgrp {
-		fsl,pins = <
-			MX6QDL_PAD_EIM_D23__UART1_DCD_B 0x1b0b0
-			MX6QDL_PAD_EIM_D24__UART1_DTR_B 0x1b0b0
-			MX6QDL_PAD_EIM_D25__UART1_DSR_B 0x1b0b0
-		>;
-	};
-
 	pinctrl_uart2_dce: uart2dcegrp {
 		fsl,pins = <
 			MX6QDL_PAD_SD4_DAT4__UART2_RX_DATA	0x1b0b1
@@ -904,7 +1322,7 @@
 		>;
 	};
 
-	pinctrl_usdhc1_4bit: usdhc1grp_4bit {
+	pinctrl_usdhc1_4bit: usdhc1-4bitgrp {
 		fsl,pins = <
 			MX6QDL_PAD_SD1_CMD__SD1_CMD    0x17071
 			MX6QDL_PAD_SD1_CLK__SD1_CLK    0x10071
@@ -915,7 +1333,7 @@
 		>;
 	};
 
-	pinctrl_usdhc1_8bit: usdhc1grp_8bit {
+	pinctrl_usdhc1_8bit: usdhc1-8bitgrp {
 		fsl,pins = <
 			MX6QDL_PAD_NANDF_D0__SD1_DATA4 0x17071
 			MX6QDL_PAD_NANDF_D1__SD1_DATA5 0x17071
diff --git a/arch/arm/boot/dts/imx6qdl-aristainetos.dtsi b/arch/arm/boot/dts/imx6qdl-aristainetos.dtsi
index e21f6ac864e5..baa197c90060 100644
--- a/arch/arm/boot/dts/imx6qdl-aristainetos.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-aristainetos.dtsi
@@ -96,7 +96,7 @@
 	pinctrl-0 = <&pinctrl_ecspi4>;
 	status = "okay";
 
-	flash: m25p80@0 {
+	flash: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "micron,n25q128a11", "jedec,spi-nor";
diff --git a/arch/arm/boot/dts/imx6qdl-aristainetos2.dtsi b/arch/arm/boot/dts/imx6qdl-aristainetos2.dtsi
index 563bf9d44fe0..6b64b2fc3995 100644
--- a/arch/arm/boot/dts/imx6qdl-aristainetos2.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-aristainetos2.dtsi
@@ -131,7 +131,7 @@
 	pinctrl-0 = <&pinctrl_ecspi4>;
 	status = "okay";
 
-	flash: m25p80@1 {
+	flash: flash@1 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "micron,n25q128a11", "jedec,spi-nor";
@@ -154,112 +154,112 @@
 		regulators {
 			bcore1 {
 				regulator-name = "bcore1";
-				regulator-always-on = <1>;
+				regulator-always-on;
 				regulator-min-microvolt = <300000>;
 				regulator-max-microvolt = <3300000>;
 			};
 
 			bcore2 {
 				regulator-name = "bcore2";
-				regulator-always-on = <1>;
+				regulator-always-on;
 				regulator-min-microvolt = <300000>;
 				regulator-max-microvolt = <3300000>;
 			};
 
 			bpro {
 				regulator-name = "bpro";
-				regulator-always-on = <1>;
+				regulator-always-on;
 				regulator-min-microvolt = <300000>;
 				regulator-max-microvolt = <3300000>;
 			};
 
 			bperi {
 				regulator-name = "bperi";
-				regulator-always-on = <1>;
+				regulator-always-on;
 				regulator-min-microvolt = <300000>;
 				regulator-max-microvolt = <3300000>;
 			};
 
 			bmem {
 				regulator-name = "bmem";
-				regulator-always-on = <1>;
+				regulator-always-on;
 				regulator-min-microvolt = <300000>;
 				regulator-max-microvolt = <3300000>;
 			};
 
 			ldo2 {
 				regulator-name = "ldo2";
-				regulator-always-on = <1>;
+				regulator-always-on;
 				regulator-min-microvolt = <300000>;
 				regulator-max-microvolt = <1800000>;
 			};
 
 			ldo3 {
 				regulator-name = "ldo3";
-				regulator-always-on = <1>;
+				regulator-always-on;
 				regulator-min-microvolt = <300000>;
 				regulator-max-microvolt = <3300000>;
 			};
 
 			ldo4 {
 				regulator-name = "ldo4";
-				regulator-always-on = <1>;
+				regulator-always-on;
 				regulator-min-microvolt = <300000>;
 				regulator-max-microvolt = <3300000>;
 			};
 
 			ldo5 {
 				regulator-name = "ldo5";
-				regulator-always-on = <1>;
+				regulator-always-on;
 				regulator-min-microvolt = <300000>;
 				regulator-max-microvolt = <3300000>;
 			};
 
 			ldo6 {
 				regulator-name = "ldo6";
-				regulator-always-on = <1>;
+				regulator-always-on;
 				regulator-min-microvolt = <300000>;
 				regulator-max-microvolt = <3300000>;
 			};
 
 			ldo7 {
 				regulator-name = "ldo7";
-				regulator-always-on = <1>;
+				regulator-always-on;
 				regulator-min-microvolt = <300000>;
 				regulator-max-microvolt = <3300000>;
 			};
 
 			ldo8 {
 				regulator-name = "ldo8";
-				regulator-always-on = <1>;
+				regulator-always-on;
 				regulator-min-microvolt = <300000>;
 				regulator-max-microvolt = <3300000>;
 			};
 
 			ldo9 {
 				regulator-name = "ldo9";
-				regulator-always-on = <1>;
+				regulator-always-on;
 				regulator-min-microvolt = <300000>;
 				regulator-max-microvolt = <3300000>;
 			};
 
 			ldo10 {
 				regulator-name = "ldo10";
-				regulator-always-on = <1>;
+				regulator-always-on;
 				regulator-min-microvolt = <300000>;
 				regulator-max-microvolt = <3300000>;
 			};
 
 			ldo11 {
 				regulator-name = "ldo11";
-				regulator-always-on = <1>;
+				regulator-always-on;
 				regulator-min-microvolt = <300000>;
 				regulator-max-microvolt = <3300000>;
 			};
 
 			bio {
 				regulator-name = "bio";
-				regulator-always-on = <1>;
+				regulator-always-on;
 				regulator-min-microvolt = <1800000>;
 				regulator-max-microvolt = <1800000>;
 			};
diff --git a/arch/arm/boot/dts/imx6qdl-colibri-v1_1-uhs.dtsi b/arch/arm/boot/dts/imx6qdl-colibri-v1_1-uhs.dtsi
deleted file mode 100644
index 7672fbfc29be..000000000000
--- a/arch/arm/boot/dts/imx6qdl-colibri-v1_1-uhs.dtsi
+++ /dev/null
@@ -1,44 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+ OR MIT
-/*
- * Copyright 2020 Toradex
- */
-
-&iomuxc {
-	pinctrl_usdhc1_100mhz: usdhc1grp100mhz {
-		fsl,pins = <
-			MX6QDL_PAD_SD1_CMD__SD1_CMD    0x170b1
-			MX6QDL_PAD_SD1_CLK__SD1_CLK    0x100b1
-			MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x170b1
-			MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x170b1
-			MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x170b1
-			MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x170b1
-		>;
-	};
-
-	pinctrl_usdhc1_200mhz: usdhc1grp200mhz {
-		fsl,pins = <
-			MX6QDL_PAD_SD1_CMD__SD1_CMD    0x170f1
-			MX6QDL_PAD_SD1_CLK__SD1_CLK    0x100f1
-			MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x170f1
-			MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x170f1
-			MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x170f1
-			MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x170f1
-		>;
-	};
-};
-
-/* Colibri MMC */
-&usdhc1 {
-	pinctrl-names = "default", "state_100mhz", "state_200mhz";
-	pinctrl-0 = <&pinctrl_usdhc1 &pinctrl_mmc_cd>;
-	pinctrl-1 = <&pinctrl_usdhc1_100mhz &pinctrl_mmc_cd>;
-	pinctrl-2 = <&pinctrl_usdhc1_200mhz &pinctrl_mmc_cd>;
-	vmmc-supply = <&reg_module_3v3>;
-	vqmmc-supply = <&vgen3_reg>;
-	wakeup-source;
-	keep-power-in-suspend;
-	sd-uhs-sdr12;
-	sd-uhs-sdr25;
-	sd-uhs-sdr50;
-	sd-uhs-sdr104;
-};
diff --git a/arch/arm/boot/dts/imx6qdl-colibri.dtsi b/arch/arm/boot/dts/imx6qdl-colibri.dtsi
index 4e2a309c93fa..023e76215064 100644
--- a/arch/arm/boot/dts/imx6qdl-colibri.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-colibri.dtsi
@@ -1,11 +1,12 @@
 // SPDX-License-Identifier: GPL-2.0+ OR MIT
 /*
- * Copyright 2014-2020 Toradex
+ * Copyright 2014-2022 Toradex
  * Copyright 2012 Freescale Semiconductor, Inc.
  * Copyright 2011 Linaro Ltd.
  */
 
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pwm/pwm.h>
 
 / {
 	model = "Toradex Colibri iMX6DL/S Module";
@@ -13,11 +14,77 @@
 
 	backlight: backlight {
 		compatible = "pwm-backlight";
+		brightness-levels = <0 45 63 88 119 158 203 255>;
+		default-brightness-level = <4>;
+		enable-gpios = <&gpio3 26 GPIO_ACTIVE_HIGH>; /* Colibri BL_ON */
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gpio_bl_on>;
-		pwms = <&pwm3 0 5000000>;
-		enable-gpios = <&gpio3 26 GPIO_ACTIVE_HIGH>; /* Colibri BL_ON */
+		power-supply = <&reg_module_3v3>;
+		pwms = <&pwm3 0 5000000 PWM_POLARITY_INVERTED>;
+		status = "disabled";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_keys>;
+
+		wakeup {
+			debounce-interval = <10>;
+			gpios = <&gpio2 22 GPIO_ACTIVE_HIGH>; /* SODIMM 45 */
+			label = "Wake-Up";
+			linux,code = <KEY_WAKEUP>;
+			wakeup-source;
+		};
+	};
+
+	lcd_display: disp0 {
+		compatible = "fsl,imx-parallel-display";
+		interface-pix-fmt = "bgr666";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ipu1_lcdif>;
+		status = "disabled";
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+
+			lcd_display_in: endpoint {
+				remote-endpoint = <&ipu1_di0_disp0>;
+			};
+		};
+
+		port@1 {
+			reg = <1>;
+
+			lcd_display_out: endpoint {
+				remote-endpoint = <&lcd_panel_in>;
+			};
+		};
+	};
+
+	/* Will be filled by the bootloader */
+	memory@10000000 {
+		device_type = "memory";
+		reg = <0x10000000 0>;
+	};
+
+	panel_dpi: panel-dpi {
+		/*
+		 * edt,et057090dhu: EDT 5.7" LCD TFT
+		 * edt,et070080dh6: EDT 7.0" LCD TFT
+		 */
+		compatible = "edt,et057090dhu";
+		backlight = <&backlight>;
 		status = "disabled";
+
+		port {
+			lcd_panel_in: endpoint {
+				remote-endpoint = <&lcd_display_out>;
+			};
+		};
 	};
 
 	reg_module_3v3: regulator-module-3v3 {
@@ -38,36 +105,36 @@
 
 	reg_usb_host_vbus: regulator-usb-host-vbus {
 		compatible = "regulator-fixed";
+		gpio = <&gpio3 31 GPIO_ACTIVE_HIGH>; /* USBH_PEN */
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_regulator_usbh_pwr>;
-		regulator-name = "usb_host_vbus";
-		regulator-min-microvolt = <5000000>;
 		regulator-max-microvolt = <5000000>;
-		gpio = <&gpio3 31 GPIO_ACTIVE_HIGH>; /* USBH_PEN */
+		regulator-min-microvolt = <5000000>;
+		regulator-name = "usb_host_vbus";
 		status = "disabled";
 	};
 
 	sound {
 		compatible = "fsl,imx-audio-sgtl5000";
-		model = "imx6dl-colibri-sgtl5000";
-		ssi-controller = <&ssi1>;
 		audio-codec = <&codec>;
 		audio-routing =
 			"Headphone Jack", "HP_OUT",
 			"LINE_IN", "Line In Jack",
 			"MIC_IN", "Mic Jack",
 			"Mic Jack", "Mic Bias";
+		model = "imx6dl-colibri-sgtl5000";
 		mux-int-port = <1>;
 		mux-ext-port = <5>;
+		ssi-controller = <&ssi1>;
 	};
 
 	/* Optional S/PDIF in on SODIMM 88 and out on SODIMM 90, 137 or 168 */
 	sound_spdif: sound-spdif {
 		compatible = "fsl,imx-audio-spdif";
-		model = "imx-spdif";
 		spdif-controller = <&spdif>;
 		spdif-in;
 		spdif-out;
+		model = "imx-spdif";
 		status = "disabled";
 	};
 };
@@ -92,6 +159,10 @@
 	status = "disabled";
 };
 
+&clks {
+	fsl,pmic-stby-poweroff;
+};
+
 /* Colibri SSP */
 &ecspi4 {
 	cs-gpios = <&gpio5 2 GPIO_ACTIVE_LOW>;
@@ -101,10 +172,10 @@
 };
 
 &fec {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_enet>;
 	phy-mode = "rmii";
 	phy-handle = <&ethphy>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet>;
 	status = "okay";
 
 	mdio {
@@ -118,6 +189,224 @@
 	};
 };
 
+&gpio1 {
+	gpio-line-names = "",
+			  "SODIMM_67",
+			  "SODIMM_180",
+			  "SODIMM_196",
+			  "SODIMM_174",
+			  "SODIMM_176",
+			  "SODIMM_194",
+			  "SODIMM_55",
+			  "SODIMM_63",
+			  "SODIMM_28",
+			  "SODIMM_93",
+			  "SODIMM_69",
+			  "SODIMM_99",
+			  "SODIMM_130",
+			  "SODIMM_106",
+			  "SODIMM_98",
+			  "SODIMM_192",
+			  "SODIMM_49",
+			  "SODIMM_190",
+			  "SODIMM_51",
+			  "SODIMM_47",
+			  "SODIMM_53",
+			  "",
+			  "SODIMM_22";
+};
+
+&gpio2 {
+	gpio-line-names = "SODIMM_132",
+			  "SODIMM_134",
+			  "SODIMM_135",
+			  "SODIMM_133",
+			  "SODIMM_102",
+			  "SODIMM_43",
+			  "SODIMM_127",
+			  "SODIMM_37",
+			  "SODIMM_104",
+			  "SODIMM_59",
+			  "SODIMM_30",
+			  "SODIMM_100",
+			  "SODIMM_38",
+			  "SODIMM_34",
+			  "SODIMM_32",
+			  "SODIMM_36",
+			  "SODIMM_59",
+			  "SODIMM_67",
+			  "SODIMM_97",
+			  "SODIMM_79",
+			  "SODIMM_103",
+			  "SODIMM_101",
+			  "SODIMM_45",
+			  "SODIMM_105",
+			  "SODIMM_107",
+			  "SODIMM_91",
+			  "SODIMM_89",
+			  "SODIMM_150",
+			  "SODIMM_126",
+			  "SODIMM_128",
+			  "",
+			  "SODIMM_94";
+};
+
+&gpio3 {
+	gpio-line-names = "SODIMM_111",
+			  "SODIMM_113",
+			  "SODIMM_115",
+			  "SODIMM_117",
+			  "SODIMM_119",
+			  "SODIMM_121",
+			  "SODIMM_123",
+			  "SODIMM_125",
+			  "SODIMM_110",
+			  "SODIMM_112",
+			  "SODIMM_114",
+			  "SODIMM_116",
+			  "SODIMM_118",
+			  "SODIMM_120",
+			  "SODIMM_122",
+			  "SODIMM_124",
+			  "",
+			  "SODIMM_96",
+			  "SODIMM_77",
+			  "SODIMM_25",
+			  "SODIMM_27",
+			  "SODIMM_88",
+			  "SODIMM_90",
+			  "SODIMM_31",
+			  "SODIMM_23",
+			  "SODIMM_29",
+			  "SODIMM_71",
+			  "SODIMM_73",
+			  "SODIMM_92",
+			  "SODIMM_81",
+			  "SODIMM_131",
+			  "SODIMM_129";
+};
+
+&gpio4 {
+	gpio-line-names = "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "SODIMM_168",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "SODIMM_184",
+			  "SODIMM_186",
+			  "HDMI_15",
+			  "HDMI_16",
+			  "SODIMM_178",
+			  "SODIMM_188",
+			  "SODIMM_56",
+			  "SODIMM_44",
+			  "SODIMM_68",
+			  "SODIMM_82",
+			  "SODIMM_24",
+			  "SODIMM_76",
+			  "SODIMM_70",
+			  "SODIMM_60",
+			  "SODIMM_58",
+			  "SODIMM_78",
+			  "SODIMM_72",
+			  "SODIMM_80",
+			  "SODIMM_46",
+			  "SODIMM_62",
+			  "SODIMM_48",
+			  "SODIMM_74";
+};
+
+&gpio5 {
+	gpio-line-names = "SODIMM_95",
+			  "",
+			  "SODIMM_86",
+			  "",
+			  "SODIMM_65",
+			  "SODIMM_50",
+			  "SODIMM_52",
+			  "SODIMM_54",
+			  "SODIMM_66",
+			  "SODIMM_64",
+			  "SODIMM_57",
+			  "SODIMM_61",
+			  "SODIMM_136",
+			  "SODIMM_138",
+			  "SODIMM_140",
+			  "SODIMM_142",
+			  "SODIMM_144",
+			  "SODIMM_146",
+			  "SODIMM_172",
+			  "SODIMM_170",
+			  "SODIMM_149",
+			  "SODIMM_151",
+			  "SODIMM_153",
+			  "SODIMM_155",
+			  "SODIMM_157",
+			  "SODIMM_159",
+			  "SODIMM_161",
+			  "SODIMM_163",
+			  "SODIMM_33",
+			  "SODIMM_35",
+			  "SODIMM_165",
+			  "SODIMM_167";
+};
+
+&gpio6 {
+	gpio-line-names = "SODIMM_169",
+			  "SODIMM_171",
+			  "SODIMM_173",
+			  "SODIMM_175",
+			  "SODIMM_177",
+			  "SODIMM_179",
+			  "SODIMM_85",
+			  "SODIMM_166",
+			  "SODIMM_160",
+			  "SODIMM_162",
+			  "SODIMM_158",
+			  "SODIMM_164",
+			  "",
+			  "",
+			  "SODIMM_156",
+			  "SODIMM_75",
+			  "SODIMM_154",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "SODIMM_152";
+};
+
+&gpio7 {
+	gpio-line-names = "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "SODIMM_19",
+			  "SODIMM_21",
+			  "",
+			  "SODIMM_137";
+};
+
 &hdmi {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_hdmi_ddc>;
@@ -132,65 +421,66 @@
 	clock-frequency = <100000>;
 	pinctrl-names = "default", "gpio";
 	pinctrl-0 = <&pinctrl_i2c2>;
-	pinctrl-0 = <&pinctrl_i2c2_gpio>;
+	pinctrl-1 = <&pinctrl_i2c2_gpio>;
 	scl-gpios = <&gpio2 30 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 	sda-gpios = <&gpio3 16 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 	status = "okay";
 
-	pmic: pfuze100@8 {
+	pmic: pmic@8 {
 		compatible = "fsl,pfuze100";
+		fsl,pmic-stby-poweroff;
 		reg = <0x08>;
 
 		regulators {
 			sw1a_reg: sw1ab {
-				regulator-min-microvolt = <300000>;
-				regulator-max-microvolt = <1875000>;
-				regulator-boot-on;
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1875000>;
+				regulator-min-microvolt = <300000>;
 				regulator-ramp-delay = <6250>;
 			};
 
 			sw1c_reg: sw1c {
-				regulator-min-microvolt = <300000>;
-				regulator-max-microvolt = <1875000>;
-				regulator-boot-on;
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1875000>;
+				regulator-min-microvolt = <300000>;
 				regulator-ramp-delay = <6250>;
 			};
 
 			sw3a_reg: sw3a {
-				regulator-min-microvolt = <400000>;
-				regulator-max-microvolt = <1975000>;
-				regulator-boot-on;
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1975000>;
+				regulator-min-microvolt = <400000>;
 			};
 
 			swbst_reg: swbst {
-				regulator-min-microvolt = <5000000>;
-				regulator-max-microvolt = <5150000>;
-				regulator-boot-on;
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <5150000>;
+				regulator-min-microvolt = <5000000>;
 			};
 
 			snvs_reg: vsnvs {
-				regulator-min-microvolt = <1000000>;
-				regulator-max-microvolt = <3000000>;
-				regulator-boot-on;
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <3000000>;
+				regulator-min-microvolt = <1000000>;
 			};
 
 			vref_reg: vrefddr {
-				regulator-boot-on;
 				regulator-always-on;
+				regulator-boot-on;
 			};
 
 			/* vgen1: unused */
 
 			vgen2_reg: vgen2 {
-				regulator-min-microvolt = <800000>;
-				regulator-max-microvolt = <1550000>;
-				regulator-boot-on;
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1550000>;
+				regulator-min-microvolt = <800000>;
 			};
 
 			/*
@@ -198,57 +488,60 @@
 			 * the i.MX 6 NVCC_SD1.
 			 */
 			vgen3_reg: vgen3 {
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <3300000>;
-				regulator-boot-on;
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <3300000>;
+				regulator-min-microvolt = <1800000>;
 			};
 
 			vgen4_reg: vgen4 {
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <1800000>;
-				regulator-boot-on;
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1800000>;
+				regulator-min-microvolt = <1800000>;
 			};
 
 			vgen5_reg: vgen5 {
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <3300000>;
-				regulator-boot-on;
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <3300000>;
+				regulator-min-microvolt = <1800000>;
 			};
 
 			vgen6_reg: vgen6 {
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <3300000>;
-				regulator-boot-on;
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <3300000>;
+				regulator-min-microvolt = <1800000>;
 			};
 		};
 	};
 
 	codec: sgtl5000@a {
 		compatible = "fsl,sgtl5000";
-		reg = <0x0a>;
 		clocks = <&clks IMX6QDL_CLK_CKO>;
+		lrclk-strength = <3>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_sgtl5000>;
+		reg = <0x0a>;
+		#sound-dai-cells = <0>;
 		VDDA-supply = <&reg_module_3v3_audio>;
 		VDDIO-supply = <&reg_module_3v3>;
 		VDDD-supply = <&vgen4_reg>;
-		lrclk-strength = <3>;
 	};
 
 	/* STMPE811 touch screen controller */
 	stmpe811@41 {
 		compatible = "st,stmpe811";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_touch_int>;
-		reg = <0x41>;
+		blocks = <0x5>;
 		interrupts = <20 IRQ_TYPE_LEVEL_LOW>;
 		interrupt-parent = <&gpio6>;
 		interrupt-controller;
 		id = <0>;
-		blocks = <0x5>;
 		irq-trigger = <0x1>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_touch_int>;
+		reg = <0x41>;
 		/* 3.25 MHz ADC clock speed */
 		st,adc-freq = <1>;
 		/* 12-bit ADC */
@@ -258,7 +551,7 @@
 		/* ADC converstion time: 80 clocks */
 		st,sample-time = <4>;
 
-		stmpe_touchscreen {
+		stmpe_ts: stmpe_touchscreen {
 			compatible = "st,stmpe-ts";
 			/* 8 sample average control */
 			st,ave-ctrl = <3>;
@@ -273,9 +566,10 @@
 			st,settling = <3>;
 			/* 5 ms touch detect interrupt delay */
 			st,touch-det-delay = <5>;
+			status = "disabled";
 		};
 
-		stmpe_adc {
+		stmpe_adc: stmpe_adc {
 			compatible = "st,stmpe-adc";
 			/* forbid to use ADC channels 3-0 (touch) */
 			st,norequest-mask = <0x0F>;
@@ -294,6 +588,21 @@
 	scl-gpios = <&gpio1 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 	sda-gpios = <&gpio1 6 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 	status = "disabled";
+
+	atmel_mxt_ts: touchscreen@4a {
+		compatible = "atmel,maxtouch";
+		interrupt-parent = <&gpio2>;
+		interrupts = <24 IRQ_TYPE_EDGE_FALLING>;	/* SODIMM 107 */
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_atmel_conn>;
+		reg = <0x4a>;
+		reset-gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;	/* SODIMM 106 */
+		status = "disabled";
+	};
+};
+
+&ipu1_di0_disp0 {
+	remote-endpoint = <&lcd_display_in>;
 };
 
 /* Colibri PWM<B> */
@@ -312,7 +621,6 @@
 
 /* Colibri PWM<A> */
 &pwm3 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm3>;
 	status = "disabled";
@@ -338,27 +646,27 @@
 
 /* Colibri UART_A */
 &uart1 {
+	fsl,dte-mode;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart1_dte &pinctrl_uart1_ctrl>;
-	fsl,dte-mode;
 	uart-has-rtscts;
 	status = "disabled";
 };
 
 /* Colibri UART_B */
 &uart2 {
+	fsl,dte-mode;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart2_dte>;
-	fsl,dte-mode;
 	uart-has-rtscts;
 	status = "disabled";
 };
 
 /* Colibri UART_C */
 &uart3 {
+	fsl,dte-mode;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart3_dte>;
-	fsl,dte-mode;
 	status = "disabled";
 };
 
@@ -370,24 +678,28 @@
 
 /* Colibri MMC */
 &usdhc1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc1 &pinctrl_mmc_cd>;
 	cd-gpios = <&gpio2 5 GPIO_ACTIVE_LOW>; /* MMCD */
-	disable-wp;
-	vqmmc-supply = <&reg_module_3v3>;
 	bus-width = <4>;
 	no-1-8-v;
+	disable-wp;
+	pinctrl-names = "default", "state_100mhz", "state_200mhz", "sleep";
+	pinctrl-0 = <&pinctrl_usdhc1 &pinctrl_mmc_cd>;
+	pinctrl-1 = <&pinctrl_usdhc1_100mhz &pinctrl_mmc_cd>;
+	pinctrl-2 = <&pinctrl_usdhc1_200mhz &pinctrl_mmc_cd>;
+	pinctrl-3 = <&pinctrl_usdhc1_sleep &pinctrl_mmc_cd_sleep>;
+	vmmc-supply = <&reg_module_3v3>;
+	vqmmc-supply = <&vgen3_reg>;
 	status = "disabled";
 };
 
 /* eMMC */
 &usdhc3 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc3>;
-	vqmmc-supply = <&reg_module_3v3>;
 	bus-width = <8>;
 	no-1-8-v;
 	non-removable;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	vqmmc-supply = <&reg_module_3v3>;
 	status = "okay";
 };
 
@@ -405,14 +717,34 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usbh_oc_1>;
 
+	/* Atmel MXT touchsceen + Capacitive Touch Adapter */
+	/* NOTE: This pin group conflicts with pin groups
+	 * pinctrl_pwm1/pinctrl_pwm4. Don't use them simultaneously.
+	 */
+	pinctrl_atmel_adap: atmeladaptergrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_9__GPIO1_IO09   0xb0b1  /* SODIMM  28 */
+			MX6QDL_PAD_SD4_DAT2__GPIO2_IO10 0xb0b1  /* SODIMM  30 */
+		>;
+	};
+
+	/* Atmel MXT touchsceen + boards with built-in Capacitive Touch Connector */
+	/* NOTE: This pin group conflicts with pin groups pinctrl_weim_cs1 and
+	 * pinctrl_weim_cs2. Don't use them simultaneously.
+	 */
+	pinctrl_atmel_conn: atmelconnectorgrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_CS1__GPIO2_IO24  0xb0b1  /* SODIMM_107 */
+			MX6QDL_PAD_SD2_DAT1__GPIO1_IO14 0xb0b1  /* SODIMM_106 */
+		>;
+	};
+
 	pinctrl_audmux: audmuxgrp {
 		fsl,pins = <
 			MX6QDL_PAD_KEY_COL0__AUD5_TXC	0x130b0
 			MX6QDL_PAD_KEY_ROW0__AUD5_TXD	0x130b0
 			MX6QDL_PAD_KEY_COL1__AUD5_TXFS	0x130b0
 			MX6QDL_PAD_KEY_ROW1__AUD5_RXD	0x130b0
-			/* SGTL5000 sys_mclk */
-			MX6QDL_PAD_GPIO_0__CCM_CLKO1	0x000b0
 		>;
 	};
 
@@ -423,28 +755,52 @@
 		>;
 	};
 
+	/* CSI pins used as GPIOs */
+	pinctrl_csi_gpio_1: csigpio1grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D18__GPIO3_IO18   0x1b0b0
+			MX6QDL_PAD_EIM_A19__GPIO2_IO19   0x1b0b0
+			MX6QDL_PAD_EIM_D29__GPIO3_IO29   0x130b0
+			MX6QDL_PAD_EIM_A23__GPIO6_IO06   0x1b0b0
+			MX6QDL_PAD_EIM_A20__GPIO2_IO18   0x1b0b0
+			MX6QDL_PAD_EIM_A17__GPIO2_IO21   0x1b0b0
+			MX6QDL_PAD_EIM_A18__GPIO2_IO20   0x1b0b0
+			MX6QDL_PAD_EIM_EB3__GPIO2_IO31   0x1b0b0
+			MX6QDL_PAD_EIM_D17__GPIO3_IO17   0x1b0b0
+			MX6QDL_PAD_NANDF_CS2__GPIO6_IO15 0x1b0b0
+			MX6QDL_PAD_SD2_CMD__GPIO1_IO11   0x1b0b0
+			MX6QDL_PAD_SD2_DAT0__GPIO1_IO15  0x1b0b0
+		>;
+	};
+
+	pinctrl_csi_gpio_2: csigpio2grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_A24__GPIO5_IO04   0x1b0b0
+		>;
+	};
+
 	pinctrl_ecspi4: ecspi4grp {
 		fsl,pins = <
+			/* SPI CS */
+			MX6QDL_PAD_EIM_A25__GPIO5_IO02	0x000b1
 			MX6QDL_PAD_EIM_D22__ECSPI4_MISO	0x100b1
 			MX6QDL_PAD_EIM_D28__ECSPI4_MOSI	0x100b1
 			MX6QDL_PAD_EIM_D21__ECSPI4_SCLK 0x100b1
-			/* SPI CS */
-			MX6QDL_PAD_EIM_A25__GPIO5_IO02	0x000b1
 		>;
 	};
 
 	pinctrl_enet: enetgrp {
 		fsl,pins = <
+			MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN	0x1b0b0
 			MX6QDL_PAD_ENET_MDC__ENET_MDC		0x1b0b0
 			MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x1b0b0
+			MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER	0x1b0b0
 			MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0	0x1b0b0
 			MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1	0x1b0b0
-			MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER	0x1b0b0
 			MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN	0x1b0b0
 			MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0	0x1b0b0
 			MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1	0x1b0b0
-			MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN	0x1b0b0
-			MX6QDL_PAD_GPIO_16__ENET_REF_CLK     ((1<<30) | 0x1b0b0)
+			MX6QDL_PAD_GPIO_16__ENET_REF_CLK	((1<<30) | 0x1b0b0)
 		>;
 	};
 
@@ -462,13 +818,32 @@
 		>;
 	};
 
-	pinctrl_gpio_bl_on: gpioblon {
+	pinctrl_gpio_1: gpio1grp {
+		fsl,pins = <
+			MX6QDL_PAD_DI0_PIN4__GPIO4_IO20     0x1b0b0
+			MX6QDL_PAD_EIM_D27__GPIO3_IO27      0x1b0b0
+			MX6QDL_PAD_ENET_REF_CLK__GPIO1_IO23 0x1b0b0
+			MX6QDL_PAD_NANDF_D3__GPIO2_IO03     0x1b0b0
+			MX6QDL_PAD_NANDF_D4__GPIO2_IO04     0x1b0b0
+			MX6QDL_PAD_NANDF_D6__GPIO2_IO06     0x1b0b0
+			MX6QDL_PAD_SD4_DAT0__GPIO2_IO08     0x1b0b0
+			MX6QDL_PAD_SD4_DAT3__GPIO2_IO11     0x1b0b0
+		>;
+	};
+	pinctrl_gpio_2: gpio2grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_7__GPIO1_IO07       0x1b0b0
+			MX6QDL_PAD_GPIO_8__GPIO1_IO08       0x1b0b0
+		>;
+	};
+
+	pinctrl_gpio_bl_on: gpioblongrp {
 		fsl,pins = <
 			MX6QDL_PAD_EIM_D26__GPIO3_IO26		0x1b0b0
 		>;
 	};
 
-	pinctrl_gpio_keys: gpiokeys {
+	pinctrl_gpio_keys: gpiokeysgrp {
 		fsl,pins = <
 			MX6QDL_PAD_EIM_A16__GPIO2_IO22		0x130b0
 		>;
@@ -483,15 +858,15 @@
 
 	pinctrl_i2c2: i2c2grp {
 		fsl,pins = <
-			MX6QDL_PAD_EIM_EB2__I2C2_SCL 0x4001b8b1
 			MX6QDL_PAD_EIM_D16__I2C2_SDA 0x4001b8b1
+			MX6QDL_PAD_EIM_EB2__I2C2_SCL 0x4001b8b1
 		>;
 	};
 
-	pinctrl_i2c2_gpio: i2c2grp {
+	pinctrl_i2c2_gpio: i2c2gpiogrp {
 		fsl,pins = <
-			MX6QDL_PAD_EIM_EB2__GPIO2_IO30 0x4001b8b1
 			MX6QDL_PAD_EIM_D16__GPIO3_IO16 0x4001b8b1
+			MX6QDL_PAD_EIM_EB2__GPIO2_IO30 0x4001b8b1
 		>;
 	};
 
@@ -523,8 +898,8 @@
 			MX6QDL_PAD_EIM_EB3__IPU1_CSI1_HSYNC	0xb0b1
 			MX6QDL_PAD_EIM_D29__IPU1_CSI1_VSYNC	0xb0b1
 			/* Disable PWM pins on camera interface */
-			MX6QDL_PAD_SD4_DAT1__GPIO2_IO09		0x40
 			MX6QDL_PAD_GPIO_1__GPIO1_IO01		0x40
+			MX6QDL_PAD_SD4_DAT1__GPIO2_IO09		0x40
 		>;
 	};
 
@@ -555,19 +930,34 @@
 		>;
 	};
 
-	pinctrl_mic_gnd: gpiomicgnd {
+	pinctrl_lvds_transceiver: lvdstxgrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_WAIT__GPIO5_IO00 0x03030 /* SODIMM  95 */
+			MX6QDL_PAD_GPIO_7__GPIO1_IO07   0x0b030 /* SODIMM  55 */
+			MX6QDL_PAD_GPIO_8__GPIO1_IO08   0x03030 /* SODIMM  63 */
+			MX6QDL_PAD_SD2_DAT3__GPIO1_IO12 0x03030 /* SODIMM  99 */
+		>;
+	};
+
+	pinctrl_mic_gnd: micgndgrp {
 		fsl,pins = <
 			/* Controls Mic GND, PU or '1' pull Mic GND to GND */
 			MX6QDL_PAD_RGMII_TD1__GPIO6_IO21 0x1b0b0
 		>;
 	};
 
-	pinctrl_mmc_cd: gpiommccd {
+	pinctrl_mmc_cd: mmccdgrp {
 		fsl,pins = <
 			MX6QDL_PAD_NANDF_D5__GPIO2_IO05	0x1b0b1
 		>;
 	};
 
+	pinctrl_mmc_cd_sleep: mmccdslpgrp {
+		fsl,pins = <
+			MX6QDL_PAD_NANDF_D5__GPIO2_IO05	0x0
+		>;
+	};
+
 	pinctrl_pwm1: pwm1grp {
 		fsl,pins = <
 			MX6QDL_PAD_GPIO_9__PWM1_OUT	0x1b0b1
@@ -576,15 +966,15 @@
 
 	pinctrl_pwm2: pwm2grp {
 		fsl,pins = <
-			MX6QDL_PAD_GPIO_1__PWM2_OUT	0x1b0b1
 			MX6QDL_PAD_EIM_A21__GPIO2_IO17	0x00040
+			MX6QDL_PAD_GPIO_1__PWM2_OUT	0x1b0b1
 		>;
 	};
 
 	pinctrl_pwm3: pwm3grp {
 		fsl,pins = <
-			MX6QDL_PAD_SD4_DAT1__PWM3_OUT	0x1b0b1
 			MX6QDL_PAD_EIM_A22__GPIO2_IO16	0x00040
+			MX6QDL_PAD_SD4_DAT1__PWM3_OUT	0x1b0b1
 		>;
 	};
 
@@ -601,10 +991,10 @@
 		>;
 	};
 
-	pinctrl_usbh_oc_1: usbhoc1grp {
+	pinctrl_sgtl5000: sgtl5000grp {
 		fsl,pins = <
-			/* USBH_OC */
-			MX6QDL_PAD_EIM_D30__GPIO3_IO30		0x1b0b0
+			/* SGTL5000 sys_mclk */
+			MX6QDL_PAD_GPIO_0__CCM_CLKO1	0x000b0
 		>;
 	};
 
@@ -650,9 +1040,9 @@
 	pinctrl_uart2_dte: uart2dtegrp {
 		fsl,pins = <
 			MX6QDL_PAD_SD4_DAT4__UART2_TX_DATA	0x1b0b1
-			MX6QDL_PAD_SD4_DAT7__UART2_RX_DATA	0x1b0b1
-			MX6QDL_PAD_SD4_DAT6__UART2_RTS_B	0x1b0b1
 			MX6QDL_PAD_SD4_DAT5__UART2_CTS_B	0x1b0b1
+			MX6QDL_PAD_SD4_DAT6__UART2_RTS_B	0x1b0b1
+			MX6QDL_PAD_SD4_DAT7__UART2_RX_DATA	0x1b0b1
 		>;
 	};
 
@@ -667,20 +1057,27 @@
 		fsl,pins = <
 			/* USBC_DET */
 			MX6QDL_PAD_GPIO_17__GPIO7_IO12		0x1b0b0
-			/* USBC_DET_EN */
-			MX6QDL_PAD_RGMII_TX_CTL__GPIO6_IO26	0x0f058
 			/* USBC_DET_OVERWRITE */
 			MX6QDL_PAD_RGMII_RXC__GPIO6_IO30	0x0f058
+			/* USBC_DET_EN */
+			MX6QDL_PAD_RGMII_TX_CTL__GPIO6_IO26	0x0f058
 		>;
 	};
 
-	pinctrl_usbc_id_1: usbc_id-1 {
+	pinctrl_usbc_id_1: usbcid1grp {
 		fsl,pins = <
 			/* USBC_ID */
 			MX6QDL_PAD_NANDF_D2__GPIO2_IO02		0x1b0b0
 		>;
 	};
 
+	pinctrl_usbh_oc_1: usbhoc1grp {
+		fsl,pins = <
+			/* USBH_OC */
+			MX6QDL_PAD_EIM_D30__GPIO3_IO30		0x1b0b0
+		>;
+	};
+
 	pinctrl_usdhc1: usdhc1grp {
 		fsl,pins = <
 			MX6QDL_PAD_SD1_CMD__SD1_CMD	0x17071
@@ -692,6 +1089,40 @@
 		>;
 	};
 
+	pinctrl_usdhc1_100mhz: usdhc1-100mhzgrp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_CMD__SD1_CMD    0x170b1
+			MX6QDL_PAD_SD1_CLK__SD1_CLK    0x100b1
+			MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x170b1
+			MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x170b1
+			MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x170b1
+			MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x170b1
+		>;
+	};
+
+	pinctrl_usdhc1_200mhz: usdhc1-200mhzgrp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_CMD__SD1_CMD    0x170f1
+			MX6QDL_PAD_SD1_CLK__SD1_CLK    0x100f1
+			MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x170f1
+			MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x170f1
+			MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x170f1
+			MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x170f1
+		>;
+	};
+
+	/* avoid backfeeding with removed card power */
+	pinctrl_usdhc1_sleep: usdhc1sleepgrp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_CMD__SD1_CMD	0x3000
+			MX6QDL_PAD_SD1_CLK__SD1_CLK	0x3000
+			MX6QDL_PAD_SD1_DAT0__SD1_DATA0	0x3000
+			MX6QDL_PAD_SD1_DAT1__SD1_DATA1	0x3000
+			MX6QDL_PAD_SD1_DAT2__SD1_DATA2	0x3000
+			MX6QDL_PAD_SD1_DAT3__SD1_DATA3	0x3000
+		>;
+	};
+
 	pinctrl_usdhc3: usdhc3grp {
 		fsl,pins = <
 			MX6QDL_PAD_SD3_CMD__SD3_CMD	0x17059
@@ -730,135 +1161,136 @@
 		>;
 	};
 
-	pinctrl_weim_sram: weimsramgrp {
-		fsl,pins = <
-			MX6QDL_PAD_EIM_OE__EIM_OE_B		0xb0b1
-			MX6QDL_PAD_EIM_RW__EIM_RW		0xb0b1
-			/* Data */
-			MX6QDL_PAD_CSI0_DATA_EN__EIM_DATA00	0x1b0b0
-			MX6QDL_PAD_CSI0_VSYNC__EIM_DATA01	0x1b0b0
-			MX6QDL_PAD_CSI0_DAT4__EIM_DATA02	0x1b0b0
-			MX6QDL_PAD_CSI0_DAT5__EIM_DATA03	0x1b0b0
-			MX6QDL_PAD_CSI0_DAT6__EIM_DATA04	0x1b0b0
-			MX6QDL_PAD_CSI0_DAT7__EIM_DATA05	0x1b0b0
-			MX6QDL_PAD_CSI0_DAT8__EIM_DATA06	0x1b0b0
-			MX6QDL_PAD_CSI0_DAT9__EIM_DATA07	0x1b0b0
-			MX6QDL_PAD_CSI0_DAT12__EIM_DATA08	0x1b0b0
-			MX6QDL_PAD_CSI0_DAT13__EIM_DATA09	0x1b0b0
-			MX6QDL_PAD_CSI0_DAT14__EIM_DATA10	0x1b0b0
-			MX6QDL_PAD_CSI0_DAT15__EIM_DATA11	0x1b0b0
-			MX6QDL_PAD_CSI0_DAT16__EIM_DATA12	0x1b0b0
-			MX6QDL_PAD_CSI0_DAT17__EIM_DATA13	0x1b0b0
-			MX6QDL_PAD_CSI0_DAT18__EIM_DATA14	0x1b0b0
-			MX6QDL_PAD_CSI0_DAT19__EIM_DATA15	0x1b0b0
-			/* Address */
-			MX6QDL_PAD_EIM_DA15__EIM_AD15		0xb0b1
-			MX6QDL_PAD_EIM_DA14__EIM_AD14		0xb0b1
-			MX6QDL_PAD_EIM_DA13__EIM_AD13		0xb0b1
-			MX6QDL_PAD_EIM_DA12__EIM_AD12		0xb0b1
-			MX6QDL_PAD_EIM_DA11__EIM_AD11		0xb0b1
-			MX6QDL_PAD_EIM_DA10__EIM_AD10		0xb0b1
-			MX6QDL_PAD_EIM_DA9__EIM_AD09		0xb0b1
-			MX6QDL_PAD_EIM_DA8__EIM_AD08		0xb0b1
-			MX6QDL_PAD_EIM_DA7__EIM_AD07		0xb0b1
-			MX6QDL_PAD_EIM_DA6__EIM_AD06		0xb0b1
-			MX6QDL_PAD_EIM_DA5__EIM_AD05		0xb0b1
-			MX6QDL_PAD_EIM_DA4__EIM_AD04		0xb0b1
-			MX6QDL_PAD_EIM_DA3__EIM_AD03		0xb0b1
-			MX6QDL_PAD_EIM_DA2__EIM_AD02		0xb0b1
-			MX6QDL_PAD_EIM_DA1__EIM_AD01		0xb0b1
-			MX6QDL_PAD_EIM_DA0__EIM_AD00		0xb0b1
-		>;
-	};
-
-	pinctrl_weim_rdnwr: weimrdnwr {
-		fsl,pins = <
-			MX6QDL_PAD_SD2_CLK__GPIO1_IO10		0x0040
-			MX6QDL_PAD_RGMII_TD3__GPIO6_IO23	0x130b0
-		>;
-	};
-
-	pinctrl_weim_npwe: weimnpwe {
-		fsl,pins = <
-			MX6QDL_PAD_SD2_DAT3__GPIO1_IO12		0x0040
-			MX6QDL_PAD_RGMII_TD2__GPIO6_IO22	0x130b0
-		>;
-	};
-
 	/* ADDRESS[16:18] [25] used as GPIO */
-	pinctrl_weim_gpio_1: weimgpio-1 {
+	pinctrl_weim_gpio_1: weimgpio1grp {
 		fsl,pins = <
-			MX6QDL_PAD_KEY_ROW4__GPIO4_IO15		0x1b0b0
-			MX6QDL_PAD_KEY_ROW2__GPIO4_IO11		0x1b0b0
-			MX6QDL_PAD_KEY_COL2__GPIO4_IO10		0x1b0b0
 			MX6QDL_PAD_DISP0_DAT23__GPIO5_IO17	0x1b0b0
 			MX6QDL_PAD_DISP0_DAT22__GPIO5_IO16	0x1b0b0
 			MX6QDL_PAD_DISP0_DAT21__GPIO5_IO15	0x1b0b0
 			MX6QDL_PAD_DISP0_DAT20__GPIO5_IO14	0x1b0b0
 			MX6QDL_PAD_DISP0_DAT19__GPIO5_IO13	0x1b0b0
 			MX6QDL_PAD_DISP0_DAT18__GPIO5_IO12	0x1b0b0
+			MX6QDL_PAD_KEY_COL2__GPIO4_IO10		0x1b0b0
+			MX6QDL_PAD_KEY_ROW4__GPIO4_IO15		0x1b0b0
+			MX6QDL_PAD_KEY_ROW2__GPIO4_IO11		0x1b0b0
 			MX6QDL_PAD_NANDF_D1__GPIO2_IO01		0x1b0b0
 		>;
 	};
 
 	/* ADDRESS[19:24] used as GPIO */
-	pinctrl_weim_gpio_2: weimgpio-2 {
+	pinctrl_weim_gpio_2: weimgpio2grp {
 		fsl,pins = <
-			MX6QDL_PAD_KEY_ROW2__GPIO4_IO11		0x1b0b0
-			MX6QDL_PAD_KEY_COL2__GPIO4_IO10		0x1b0b0
-			MX6QDL_PAD_DISP0_DAT23__GPIO5_IO17	0x1b0b0
-			MX6QDL_PAD_DISP0_DAT22__GPIO5_IO16	0x1b0b0
-			MX6QDL_PAD_DISP0_DAT21__GPIO5_IO15	0x1b0b0
-			MX6QDL_PAD_DISP0_DAT20__GPIO5_IO14	0x1b0b0
-			MX6QDL_PAD_DISP0_DAT19__GPIO5_IO13	0x1b0b0
 			MX6QDL_PAD_DISP0_DAT18__GPIO5_IO12	0x1b0b0
+			MX6QDL_PAD_DISP0_DAT19__GPIO5_IO13	0x1b0b0
+			MX6QDL_PAD_DISP0_DAT20__GPIO5_IO14	0x1b0b0
+			MX6QDL_PAD_DISP0_DAT21__GPIO5_IO15	0x1b0b0
+			MX6QDL_PAD_DISP0_DAT22__GPIO5_IO16	0x1b0b0
+			MX6QDL_PAD_DISP0_DAT23__GPIO5_IO17	0x1b0b0
+			MX6QDL_PAD_KEY_COL2__GPIO4_IO10		0x1b0b0
+			MX6QDL_PAD_KEY_ROW2__GPIO4_IO11		0x1b0b0
 			MX6QDL_PAD_NANDF_D1__GPIO2_IO01		0x1b0b0
 		>;
 	};
 
 	/* DATA[16:31] used as GPIO */
-	pinctrl_weim_gpio_3: weimgpio-3 {
+	pinctrl_weim_gpio_3: weimgpio3grp {
 		fsl,pins = <
+			MX6QDL_PAD_CSI0_MCLK__GPIO5_IO19	0x1b0b0
+			MX6QDL_PAD_CSI0_PIXCLK__GPIO5_IO18	0x1b0b0
 			MX6QDL_PAD_EIM_LBA__GPIO2_IO27		0x1b0b0
 			MX6QDL_PAD_EIM_BCLK__GPIO6_IO31		0x1b0b0
-			MX6QDL_PAD_NANDF_CS3__GPIO6_IO16	0x1b0b0
-			MX6QDL_PAD_NANDF_CS1__GPIO6_IO14	0x1b0b0
-			MX6QDL_PAD_NANDF_RB0__GPIO6_IO10	0x1b0b0
+			MX6QDL_PAD_GPIO_2__GPIO1_IO02		0x1b0b0
+			MX6QDL_PAD_GPIO_4__GPIO1_IO04		0x1b0b0
+			MX6QDL_PAD_GPIO_5__GPIO1_IO05		0x1b0b0
+			MX6QDL_PAD_GPIO_19__GPIO4_IO05		0x1b0b0
 			MX6QDL_PAD_NANDF_ALE__GPIO6_IO08	0x1b0b0
-			MX6QDL_PAD_NANDF_WP_B__GPIO6_IO09	0x1b0b0
 			MX6QDL_PAD_NANDF_CS0__GPIO6_IO11	0x1b0b0
+			MX6QDL_PAD_NANDF_CS1__GPIO6_IO14	0x1b0b0
+			MX6QDL_PAD_NANDF_CS3__GPIO6_IO16	0x1b0b0
 			MX6QDL_PAD_NANDF_CLE__GPIO6_IO07	0x1b0b0
-			MX6QDL_PAD_GPIO_19__GPIO4_IO05		0x1b0b0
-			MX6QDL_PAD_CSI0_MCLK__GPIO5_IO19	0x1b0b0
-			MX6QDL_PAD_CSI0_PIXCLK__GPIO5_IO18	0x1b0b0
-			MX6QDL_PAD_GPIO_4__GPIO1_IO04		0x1b0b0
-			MX6QDL_PAD_GPIO_5__GPIO1_IO05		0x1b0b0
-			MX6QDL_PAD_GPIO_2__GPIO1_IO02		0x1b0b0
+			MX6QDL_PAD_NANDF_RB0__GPIO6_IO10	0x1b0b0
+			MX6QDL_PAD_NANDF_WP_B__GPIO6_IO09	0x1b0b0
 		>;
 	};
 
 	/* DQM[0:3] used as GPIO */
-	pinctrl_weim_gpio_4: weimgpio-4 {
+	pinctrl_weim_gpio_4: weimgpio4grp {
 		fsl,pins = <
 			MX6QDL_PAD_EIM_EB0__GPIO2_IO28		0x1b0b0
 			MX6QDL_PAD_EIM_EB1__GPIO2_IO29		0x1b0b0
-			MX6QDL_PAD_SD2_DAT2__GPIO1_IO13		0x1b0b0
 			MX6QDL_PAD_NANDF_D0__GPIO2_IO00		0x1b0b0
+			MX6QDL_PAD_SD2_DAT2__GPIO1_IO13		0x1b0b0
 		>;
 	};
 
 	/* RDY used as GPIO */
-	pinctrl_weim_gpio_5: weimgpio-5 {
+	pinctrl_weim_gpio_5: weimgpio5grp {
 		fsl,pins = <
 			MX6QDL_PAD_EIM_WAIT__GPIO5_IO00		0x1b0b0
 		>;
 	};
 
 	/* ADDRESS[16] DATA[30] used as GPIO */
-	pinctrl_weim_gpio_6: weimgpio-6 {
+	pinctrl_weim_gpio_6: weimgpio6grp {
 		fsl,pins = <
-			MX6QDL_PAD_KEY_ROW4__GPIO4_IO15		0x1b0b0
 			MX6QDL_PAD_KEY_COL4__GPIO4_IO14		0x1b0b0
+			MX6QDL_PAD_KEY_ROW4__GPIO4_IO15		0x1b0b0
+		>;
+	};
+
+	pinctrl_weim_npwe: weimnpwegrp {
+		fsl,pins = <
+			MX6QDL_PAD_RGMII_TD2__GPIO6_IO22	0x130b0
+			MX6QDL_PAD_SD2_DAT3__GPIO1_IO12		0x0040
+		>;
+	};
+
+	pinctrl_weim_sram: weimsramgrp {
+		fsl,pins = <
+			/* Data */
+			MX6QDL_PAD_CSI0_DAT4__EIM_DATA02	0x1b0b0
+			MX6QDL_PAD_CSI0_DAT5__EIM_DATA03	0x1b0b0
+			MX6QDL_PAD_CSI0_DAT6__EIM_DATA04	0x1b0b0
+			MX6QDL_PAD_CSI0_DAT7__EIM_DATA05	0x1b0b0
+			MX6QDL_PAD_CSI0_DAT8__EIM_DATA06	0x1b0b0
+			MX6QDL_PAD_CSI0_DAT9__EIM_DATA07	0x1b0b0
+			MX6QDL_PAD_CSI0_DAT12__EIM_DATA08	0x1b0b0
+			MX6QDL_PAD_CSI0_DAT13__EIM_DATA09	0x1b0b0
+			MX6QDL_PAD_CSI0_DAT14__EIM_DATA10	0x1b0b0
+			MX6QDL_PAD_CSI0_DAT15__EIM_DATA11	0x1b0b0
+			MX6QDL_PAD_CSI0_DAT16__EIM_DATA12	0x1b0b0
+			MX6QDL_PAD_CSI0_DAT17__EIM_DATA13	0x1b0b0
+			MX6QDL_PAD_CSI0_DAT18__EIM_DATA14	0x1b0b0
+			MX6QDL_PAD_CSI0_DAT19__EIM_DATA15	0x1b0b0
+			MX6QDL_PAD_CSI0_DATA_EN__EIM_DATA00	0x1b0b0
+			MX6QDL_PAD_CSI0_VSYNC__EIM_DATA01	0x1b0b0
+			/* Address */
+			MX6QDL_PAD_EIM_DA0__EIM_AD00		0xb0b1
+			MX6QDL_PAD_EIM_DA1__EIM_AD01		0xb0b1
+			MX6QDL_PAD_EIM_DA2__EIM_AD02		0xb0b1
+			MX6QDL_PAD_EIM_DA3__EIM_AD03		0xb0b1
+			MX6QDL_PAD_EIM_DA4__EIM_AD04		0xb0b1
+			MX6QDL_PAD_EIM_DA5__EIM_AD05		0xb0b1
+			MX6QDL_PAD_EIM_DA6__EIM_AD06		0xb0b1
+			MX6QDL_PAD_EIM_DA7__EIM_AD07		0xb0b1
+			MX6QDL_PAD_EIM_DA8__EIM_AD08		0xb0b1
+			MX6QDL_PAD_EIM_DA9__EIM_AD09		0xb0b1
+			MX6QDL_PAD_EIM_DA10__EIM_AD10		0xb0b1
+			MX6QDL_PAD_EIM_DA11__EIM_AD11		0xb0b1
+			MX6QDL_PAD_EIM_DA12__EIM_AD12		0xb0b1
+			MX6QDL_PAD_EIM_DA13__EIM_AD13		0xb0b1
+			MX6QDL_PAD_EIM_DA14__EIM_AD14		0xb0b1
+			MX6QDL_PAD_EIM_DA15__EIM_AD15		0xb0b1
+			/* Ctrl */
+			MX6QDL_PAD_EIM_OE__EIM_OE_B		0xb0b1
+			MX6QDL_PAD_EIM_RW__EIM_RW		0xb0b1
+		>;
+	};
+
+	pinctrl_weim_rdnwr: weimrdnwrgrp {
+		fsl,pins = <
+			MX6QDL_PAD_RGMII_TD3__GPIO6_IO23	0x130b0
+			MX6QDL_PAD_SD2_CLK__GPIO1_IO10		0x0040
 		>;
 	};
 };
diff --git a/arch/arm/boot/dts/imx6qdl-dfi-fs700-m60.dtsi b/arch/arm/boot/dts/imx6qdl-dfi-fs700-m60.dtsi
index 648f5fcb72e6..2c1d6f28e695 100644
--- a/arch/arm/boot/dts/imx6qdl-dfi-fs700-m60.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-dfi-fs700-m60.dtsi
@@ -35,7 +35,7 @@
 	pinctrl-0 = <&pinctrl_ecspi3>;
 	status = "okay";
 
-	flash: m25p80@0 {
+	flash: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "sst,sst25vf040b", "jedec,spi-nor";
diff --git a/arch/arm/boot/dts/imx6qdl-dhcom-drc02.dtsi b/arch/arm/boot/dts/imx6qdl-dhcom-drc02.dtsi
index 3d0a50a9ab21..702cd4a1b2e6 100644
--- a/arch/arm/boot/dts/imx6qdl-dhcom-drc02.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-dhcom-drc02.dtsi
@@ -95,6 +95,10 @@
 	rts-gpios = <&gpio7 13 GPIO_ACTIVE_HIGH>; /* GPIO P */
 };
 
+&usbh1 {
+	disable-over-current;
+};
+
 &usdhc2 { /* SD card */
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/imx6qdl-dhcom-pdk2.dtsi b/arch/arm/boot/dts/imx6qdl-dhcom-pdk2.dtsi
index dc21853706a5..6248b126b557 100644
--- a/arch/arm/boot/dts/imx6qdl-dhcom-pdk2.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-dhcom-pdk2.dtsi
@@ -4,7 +4,10 @@
  * Copyright (C) 2018 Marek Vasut <marex@denx.de>
  */
 
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
 #include <dt-bindings/leds/common.h>
+#include <dt-bindings/pwm/pwm.h>
 
 / {
 	chosen {
@@ -260,6 +263,10 @@
 	status = "okay";
 };
 
+&usbh1 {
+	disable-over-current;
+};
+
 &usdhc2 { /* SD card */
 	status = "okay";
 };
@@ -325,37 +332,4 @@
 			MX6QDL_PAD_GPIO_0__GPIO1_IO00		0xb1 /* Int */
 		>;
 	};
-
-	pinctrl_ipu1_lcdif: ipu1-lcdif-grp {
-		fsl,pins = <
-			MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK	0x38
-			MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02		0x38
-			MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03		0x38
-			MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15		0x38
-			MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00	0x38
-			MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01	0x38
-			MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02	0x38
-			MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03	0x38
-			MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04	0x38
-			MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05	0x38
-			MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06	0x38
-			MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07	0x38
-			MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08	0x38
-			MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09	0x38
-			MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10	0x38
-			MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11	0x38
-			MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12	0x38
-			MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13	0x38
-			MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14	0x38
-			MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15	0x38
-			MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16	0x38
-			MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17	0x38
-			MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18	0x38
-			MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19	0x38
-			MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20	0x38
-			MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21	0x38
-			MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22	0x38
-			MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23	0x38
-		>;
-	};
 };
diff --git a/arch/arm/boot/dts/imx6qdl-dhcom-som.dtsi b/arch/arm/boot/dts/imx6qdl-dhcom-som.dtsi
index 5d10c40313cb..eaa87b333164 100644
--- a/arch/arm/boot/dts/imx6qdl-dhcom-som.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-dhcom-som.dtsi
@@ -132,14 +132,15 @@
 		#size-cells = <0>;
 
 		ethphy0: ethernet-phy@0 { /* SMSC LAN8710Ai */
-			compatible = "ethernet-phy-ieee802.3-c22";
+			compatible = "ethernet-phy-id0007.c0f0",
+				     "ethernet-phy-ieee802.3-c22";
 			interrupt-parent = <&gpio4>;
 			interrupts = <15 IRQ_TYPE_LEVEL_LOW>;
 			pinctrl-0 = <&pinctrl_ethphy0>;
 			pinctrl-names = "default";
 			reg = <0>;
-			reset-assert-us = <1000>;
-			reset-deassert-us = <1000>;
+			reset-assert-us = <500>;
+			reset-deassert-us = <500>;
 			reset-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>;
 			smsc,disable-energy-detect; /* Make plugin detection reliable */
 		};
@@ -666,6 +667,39 @@
 		>;
 	};
 
+	pinctrl_ipu1_lcdif: ipu1-lcdif-grp {
+		fsl,pins = <
+			MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK	0x38
+			MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02		0x38
+			MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03		0x38
+			MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15		0x38
+			MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00	0x38
+			MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01	0x38
+			MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02	0x38
+			MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03	0x38
+			MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04	0x38
+			MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05	0x38
+			MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06	0x38
+			MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07	0x38
+			MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08	0x38
+			MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09	0x38
+			MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10	0x38
+			MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11	0x38
+			MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12	0x38
+			MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13	0x38
+			MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14	0x38
+			MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15	0x38
+			MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16	0x38
+			MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17	0x38
+			MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18	0x38
+			MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19	0x38
+			MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20	0x38
+			MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21	0x38
+			MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22	0x38
+			MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23	0x38
+		>;
+	};
+
 	pinctrl_pcie: pcie-grp {
 		fsl,pins = <
 			MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20	0x1b0b1 /* Wake */
@@ -728,6 +762,7 @@
 	pinctrl_usbh1: usbh1-grp {
 		fsl,pins = <
 			MX6QDL_PAD_EIM_D31__GPIO3_IO31		0x120b0
+			MX6QDL_PAD_EIM_D30__USB_H1_OC		0x1b0b1
 		>;
 	};
 
diff --git a/arch/arm/boot/dts/imx6qdl-gw52xx.dtsi b/arch/arm/boot/dts/imx6qdl-gw52xx.dtsi
index b1df2beb2832..728810b9d677 100644
--- a/arch/arm/boot/dts/imx6qdl-gw52xx.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-gw52xx.dtsi
@@ -137,6 +137,16 @@
 		regulator-always-on;
 	};
 
+	reg_can1_stby: regulator-can1-stby {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_can1>;
+		regulator-name = "can1_stby";
+		gpio = <&gpio1 9 GPIO_ACTIVE_LOW>;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
 	reg_usb_otg_vbus: regulator-usb-otg-vbus {
 		compatible = "regulator-fixed";
 		regulator-name = "usb_otg_vbus";
@@ -170,6 +180,7 @@
 &can1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_flexcan1>;
+	xceiver-supply = <&reg_can1_stby>;
 	status = "okay";
 };
 
@@ -612,7 +623,6 @@
 		fsl,pins = <
 			MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX	0x1b0b1
 			MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX	0x1b0b1
-			MX6QDL_PAD_GPIO_9__GPIO1_IO09		0x4001b0b0 /* CAN_STBY */
 		>;
 	};
 
@@ -702,6 +712,12 @@
 		>;
 	};
 
+	pinctrl_reg_can1: regcan1grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_9__GPIO1_IO09		0x4001b0b0 /* CAN_STBY */
+		>;
+	};
+
 	pinctrl_uart1: uart1grp {
 		fsl,pins = <
 			MX6QDL_PAD_SD3_DAT7__UART1_TX_DATA	0x1b0b1
diff --git a/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi b/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi
index a0710d562766..6c0c109046d8 100644
--- a/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi
@@ -129,6 +129,16 @@
 		regulator-always-on;
 	};
 
+	reg_can1_stby: regulator-can1-stby {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_can1>;
+		regulator-name = "can1_stby";
+		gpio = <&gpio1 2 GPIO_ACTIVE_LOW>;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
 	reg_usb_h1_vbus: regulator-usb-h1-vbus {
 		compatible = "regulator-fixed";
 		regulator-name = "usb_h1_vbus";
@@ -170,6 +180,7 @@
 &can1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_flexcan1>;
+	xceiver-supply = <&reg_can1_stby>;
 	status = "okay";
 };
 
@@ -600,7 +611,6 @@
 		fsl,pins = <
 			MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX	0x1b0b1
 			MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX	0x1b0b1
-			MX6QDL_PAD_GPIO_2__GPIO1_IO02		0x4001b0b0 /* CAN_STBY */
 		>;
 	};
 
@@ -691,6 +701,12 @@
 		>;
 	};
 
+	pinctrl_reg_can1: regcan1grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_2__GPIO1_IO02		0x4001b0b0 /* CAN_STBY */
+		>;
+	};
+
 	pinctrl_uart1: uart1grp {
 		fsl,pins = <
 			MX6QDL_PAD_SD3_DAT7__UART1_TX_DATA	0x1b0b1
diff --git a/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi b/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi
index cda48bf2f168..a9b04f9f1c2b 100644
--- a/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi
@@ -137,6 +137,16 @@
 			regulator-always-on;
 		};
 
+		reg_can1_stby: regulator-can1-stby {
+			compatible = "regulator-fixed";
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_reg_can1>;
+			regulator-name = "can1_stby";
+			gpio = <&gpio1 2 GPIO_ACTIVE_LOW>;
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+		};
+
 		reg_usb_h1_vbus: regulator@2 {
 			compatible = "regulator-fixed";
 			reg = <2>;
@@ -200,6 +210,7 @@
 &can1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_flexcan1>;
+	xceiver-supply = <&reg_can1_stby>;
 	status = "okay";
 };
 
@@ -687,7 +698,6 @@
 		fsl,pins = <
 			MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX	0x1b0b1
 			MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX	0x1b0b1
-			MX6QDL_PAD_GPIO_2__GPIO1_IO02		0x4001b0b0 /* CAN_STBY */
 		>;
 	};
 
@@ -786,6 +796,12 @@
 		>;
 	};
 
+	pinctrl_reg_can1: regcan1grp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_2__GPIO1_IO02		0x4001b0b0 /* CAN_STBY */
+		>;
+	};
+
 	pinctrl_uart1: uart1grp {
 		fsl,pins = <
 			MX6QDL_PAD_SD3_DAT7__UART1_TX_DATA	0x1b0b1
diff --git a/arch/arm/boot/dts/imx6qdl-gw5910.dtsi b/arch/arm/boot/dts/imx6qdl-gw5910.dtsi
index 68e5ab2e27e2..6bb4855d13ce 100644
--- a/arch/arm/boot/dts/imx6qdl-gw5910.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-gw5910.dtsi
@@ -29,7 +29,7 @@
 
 		user-pb {
 			label = "user_pb";
-			gpios = <&gsc_gpio 0 GPIO_ACTIVE_LOW>;
+			gpios = <&gsc_gpio 2 GPIO_ACTIVE_LOW>;
 			linux,code = <BTN_0>;
 		};
 
diff --git a/arch/arm/boot/dts/imx6qdl-gw5913.dtsi b/arch/arm/boot/dts/imx6qdl-gw5913.dtsi
index 8e23cec7149e..696427b487f0 100644
--- a/arch/arm/boot/dts/imx6qdl-gw5913.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-gw5913.dtsi
@@ -26,7 +26,7 @@
 
 		user-pb {
 			label = "user_pb";
-			gpios = <&gsc_gpio 0 GPIO_ACTIVE_LOW>;
+			gpios = <&gsc_gpio 2 GPIO_ACTIVE_LOW>;
 			linux,code = <BTN_0>;
 		};
 
diff --git a/arch/arm/boot/dts/imx6qdl-kontron-samx6i.dtsi b/arch/arm/boot/dts/imx6qdl-kontron-samx6i.dtsi
index b167b33bd108..85aeebc9485d 100644
--- a/arch/arm/boot/dts/imx6qdl-kontron-samx6i.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-kontron-samx6i.dtsi
@@ -51,16 +51,6 @@
 		vin-supply = <&reg_3p3v_s5>;
 	};
 
-	reg_3p3v_s0: regulator-3p3v-s0 {
-		compatible = "regulator-fixed";
-		regulator-name = "V_3V3_S0";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		regulator-always-on;
-		regulator-boot-on;
-		vin-supply = <&reg_3p3v_s5>;
-	};
-
 	reg_3p3v_s5: regulator-3p3v-s5 {
 		compatible = "regulator-fixed";
 		regulator-name = "V_3V3_S5";
@@ -258,8 +248,8 @@
 	status = "okay";
 
 	/* default boot source: workaround #1 for errata ERR006282 */
-	smarc_flash: spi-flash@0 {
-		compatible = "winbond,w25q16dw", "jedec,spi-nor";
+	smarc_flash: flash@0 {
+		compatible = "jedec,spi-nor";
 		reg = <0>;
 		spi-max-frequency = <20000000>;
 	};
@@ -270,7 +260,23 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
 	phy-mode = "rgmii";
-	phy-reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
+	phy-handle = <&ethphy>;
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy: ethernet-phy@1 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <1>;
+			reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <1000>;
+		};
+	};
+};
+
+&hdmi {
+	ddc-i2c-bus = <&i2c2>;
 };
 
 &i2c_intern {
@@ -397,7 +403,7 @@
 
 /* HDMI_CTRL */
 &i2c2 {
-	clock-frequency = <375000>;
+	clock-frequency = <100000>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_i2c2>;
 };
diff --git a/arch/arm/boot/dts/imx6qdl-mba6.dtsi b/arch/arm/boot/dts/imx6qdl-mba6.dtsi
new file mode 100644
index 000000000000..78555a618851
--- /dev/null
+++ b/arch/arm/boot/dts/imx6qdl-mba6.dtsi
@@ -0,0 +1,535 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright 2013 Sascha Hauer, Pengutronix
+ *
+ * Copyright 2013-2021 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+#include <dt-bindings/clock/imx6qdl-clock.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/sound/fsl-imx-audmux.h>
+
+/ {
+	aliases {
+		mmc0 = &usdhc3;
+		mmc1 = &usdhc2;
+		/delete-property/ mmc2;
+		/delete-property/ mmc3;
+		rtc0 = &rtc0;
+	};
+
+	chosen {
+		stdout-path = &uart2;
+	};
+
+	beeper: gpio-beeper {
+		compatible = "gpio-beeper";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpiobeeper>;
+		gpios = <&gpio1 21 GPIO_ACTIVE_HIGH>;
+	};
+
+	gpio_buttons: gpio-buttons {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpiobuttons>;
+
+		button1 {
+			label = "s6";
+			linux,code = <KEY_F6>;
+			gpios = <&gpio7 13 GPIO_ACTIVE_LOW>;
+			wakeup-source;
+		};
+
+		button2 {
+			label = "s7";
+			linux,code = <KEY_F7>;
+			gpios = <&gpio7 12 GPIO_ACTIVE_LOW>;
+			wakeup-source;
+		};
+
+		button3 {
+			label = "s8";
+			linux,code = <KEY_F8>;
+			gpios = <&gpio1 8 GPIO_ACTIVE_LOW>;
+			wakeup-source;
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpioled>;
+
+		led1 {
+			label = "led1";
+			gpios = <&gpio6 16 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-on";
+		};
+
+		led2 {
+			label = "led2";
+			gpios = <&gpio6 31 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	reg_mba6_3p3v: regulator-mba6-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "supply-mba6-3p3v";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	reg_pcie: regulator-pcie {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_regpcie>;
+		regulator-name = "supply-pcie";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		/* PCIE.PWR_EN */
+		gpio = <&gpio2 0 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-always-on;
+		vin-supply = <&reg_mba6_3p3v>;
+	};
+
+	reg_vcc3v3_audio: regulator-vcc3v3-audio {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3-audio";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&reg_mba6_3p3v>;
+	};
+
+	sound {
+		compatible = "fsl,imx-audio-tlv320aic32x4";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_audmux>;
+		model = "imx-audio-tlv320aic32x4";
+		ssi-controller = <&ssi1>;
+		audio-codec = <&tlv320aic32x4>;
+		audio-asrc = <&asrc>;
+		audio-routing =
+			"IN3_L", "Mic Jack",
+			"Mic Jack", "Mic Bias",
+			"IN1_L", "Line In Jack",
+			"IN1_R", "Line In Jack",
+			"Line Out Jack", "LOL",
+			"Line Out Jack", "LOR";
+		mux-int-port = <1>;
+		mux-ext-port = <3>;
+	};
+};
+
+&audmux {
+	status = "okay";
+
+	ssi0 {
+		fsl,audmux-port = <MX31_AUDMUX_PORT1_SSI0>;
+		fsl,port-config = <
+			(IMX_AUDMUX_V2_PTCR_SYN |
+				IMX_AUDMUX_V2_PTCR_TFSDIR |
+				IMX_AUDMUX_V2_PTCR_TFSEL(MX31_AUDMUX_PORT3_SSI_PINS_3) |
+				IMX_AUDMUX_V2_PTCR_TCLKDIR |
+				IMX_AUDMUX_V2_PTCR_TCSEL(MX31_AUDMUX_PORT3_SSI_PINS_3))
+			IMX_AUDMUX_V2_PDCR_RXDSEL(MX31_AUDMUX_PORT3_SSI_PINS_3)
+		>;
+	};
+
+	aud3 {
+		fsl,audmux-port = <MX31_AUDMUX_PORT3_SSI_PINS_3>;
+		fsl,port-config = <
+			IMX_AUDMUX_V2_PTCR_SYN
+			IMX_AUDMUX_V2_PDCR_RXDSEL(MX31_AUDMUX_PORT1_SSI0)
+		>;
+	};
+};
+
+&can1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can1>;
+	status = "okay";
+};
+
+&can2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can2>;
+	status = "okay";
+};
+
+&ecspi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1>, <&pinctrl_ecspi1_mba6>;
+	cs-gpios = <&gpio3 19 0>, <&gpio3 24 0>;
+};
+
+&fec {
+	phy-mode = "rgmii-id";
+	phy-handle = <&ethphy>;
+	mac-address = [00 00 00 00 00 00];
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy: ethernet-phy@3 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <3>;
+			interrupt-parent = <&gpio1>;
+			interrupts = <28 IRQ_TYPE_LEVEL_LOW>;
+			reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <1000>;
+			reset-deassert-us = <100000>;
+			micrel,force-master;
+			max-speed = <1000>;
+		};
+	};
+};
+
+&i2c1 {
+	tlv320aic32x4: audio-codec@18 {
+		compatible = "ti,tlv320aic32x4";
+		reg = <0x18>;
+		clocks = <&clks IMX6QDL_CLK_CKO>;
+		clock-names = "mclk";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_codec>;
+		ldoin-supply = <&reg_vcc3v3_audio>;
+		iov-supply = <&reg_mba6_3p3v>;
+	};
+};
+
+&pcie {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pcie>;
+	reset-gpio = <&gpio6 7 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&pwm1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm1>;
+	status = "okay";
+};
+
+&pwm3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm3>;
+	status = "okay";
+};
+
+&pwm4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm4>;
+	status = "okay";
+};
+
+&snvs_poweroff {
+	status = "okay";
+};
+
+&ssi1 {
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+	uart-has-rtscts;
+	linux,rs485-enabled-at-boot-time;
+	rs485-rts-active-low;
+	rs485-rx-during-tx;
+	status = "okay";
+};
+
+&uart5 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart5>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&usbh1 {
+	disable-over-current;
+	status = "okay";
+};
+
+&usbotg {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg>;
+	power-active-high;
+	over-current-active-low;
+	srp-disable;
+	hnp-disable;
+	adp-disable;
+	dr_mode = "otg";
+	status = "okay";
+};
+
+/* SD card slot */
+&usdhc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	vmmc-supply = <&reg_mba6_3p3v>;
+	bus-width = <4>;
+	no-1-8-v;
+	no-mmc;
+	no-sdio;
+	cd-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+};
+
+&wdog1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog1>;
+	/* does not work on unmodified starter kit */
+	/* fsl,ext-reset-output; */
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hog>;
+
+	pinctrl_audmux: audmuxgrp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT7__AUD3_RXD  0x1b0b0
+			MX6QDL_PAD_CSI0_DAT4__AUD3_TXC  0x1b0b0
+			MX6QDL_PAD_CSI0_DAT5__AUD3_TXD  0x1b0b0
+			MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x1b0b0
+		>;
+	};
+
+	pinctrl_can1: can1grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX 0xb099
+			MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX 0xb099
+		>;
+	};
+
+	pinctrl_can2: can2grp {
+		fsl,pins = <
+			MX6QDL_PAD_KEY_COL4__FLEXCAN2_TX 0xb099
+			MX6QDL_PAD_KEY_ROW4__FLEXCAN2_RX 0xb099
+		>;
+	};
+
+	pinctrl_codec: codecgrp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_MCLK__CCM_CLKO1 0xb0 /* CLK */
+		>;
+	};
+
+	pinctrl_ecspi1_mba6: ecspimba6grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D24__GPIO3_IO24 0xb099 /* eCSPI1 SS2 */
+		>;
+	};
+
+	pinctrl_enet: enetgrp {
+		fsl,pins = <
+			/* FEC phy IRQ */
+			MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28     0x00011008
+			/* FEC phy reset */
+			MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25   0x1b099
+			/* DSE = 100, 100k up, SPEED = MED */
+			MX6QDL_PAD_ENET_MDIO__ENET_MDIO       0xb0a0
+			MX6QDL_PAD_ENET_MDC__ENET_MDC         0xb0a0
+			/* DSE = 111, pull 100k up */
+			MX6QDL_PAD_RGMII_TXC__RGMII_TXC       0xb038
+			MX6QDL_PAD_RGMII_TD0__RGMII_TD0       0xb038
+			MX6QDL_PAD_RGMII_TD1__RGMII_TD1       0xb038
+			MX6QDL_PAD_RGMII_TD2__RGMII_TD2       0xb038
+			MX6QDL_PAD_RGMII_TD3__RGMII_TD3       0xb038
+			MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0xb038
+			/* DSE = 111, pull external */
+			MX6QDL_PAD_RGMII_RXC__RGMII_RXC       0x0038
+			MX6QDL_PAD_RGMII_RD0__RGMII_RD0       0x0038
+			MX6QDL_PAD_RGMII_RD1__RGMII_RD1       0x0038
+			MX6QDL_PAD_RGMII_RD2__RGMII_RD2       0x0038
+			MX6QDL_PAD_RGMII_RD3__RGMII_RD3       0x0038
+			MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x0038
+			/* HYS = 1, DSE = 111, 100k up, SPEED = HIGH */
+			MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK  0x1b0f0
+		>;
+	};
+
+	pinctrl_gpiobeeper: gpiobeepergrp {
+		fsl,pins = <
+			MX6QDL_PAD_SD1_DAT3__GPIO1_IO21 0xb099
+		>;
+	};
+
+	pinctrl_gpiobuttons: gpiobuttongrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x0001b099
+			MX6QDL_PAD_GPIO_18__GPIO7_IO13 0x0001b099
+			MX6QDL_PAD_GPIO_8__GPIO1_IO08 0x0001b099
+		>;
+	};
+
+	pinctrl_gpioled: gpioledgrp {
+		fsl,pins = <
+			MX6QDL_PAD_NANDF_CS3__GPIO6_IO16 0xb099 /* LED V15 */
+			MX6QDL_PAD_EIM_BCLK__GPIO6_IO31 0xb099 /* LED V16 */
+		>;
+	};
+
+	pinctrl_hog: hoggrp {
+		fsl,pins = <
+			MX6QDL_PAD_DI0_PIN4__GPIO4_IO20 0x0001b099
+
+			MX6QDL_PAD_ENET_RXD1__GPIO1_IO26 0x0001b099
+			MX6QDL_PAD_ENET_TXD1__GPIO1_IO29 0x0001b099
+			MX6QDL_PAD_ENET_TXD0__GPIO1_IO30 0x0001b099
+
+			MX6QDL_PAD_NANDF_D1__GPIO2_IO01 0x0001b099
+			MX6QDL_PAD_NANDF_D2__GPIO2_IO02 0x0001b099
+			MX6QDL_PAD_NANDF_D3__GPIO2_IO03 0x0001b099
+			MX6QDL_PAD_SD4_DAT0__GPIO2_IO08 0x0001b099
+			MX6QDL_PAD_EIM_CS0__GPIO2_IO23 0x0001b099
+			MX6QDL_PAD_EIM_CS1__GPIO2_IO24 0x0001b099
+			MX6QDL_PAD_EIM_OE__GPIO2_IO25 0x0001b099
+
+			MX6QDL_PAD_EIM_D20__GPIO3_IO20 0x0001b099
+			MX6QDL_PAD_EIM_D26__GPIO3_IO26 0x0001b099
+			MX6QDL_PAD_EIM_D27__GPIO3_IO27 0x0001b099
+			MX6QDL_PAD_EIM_D28__GPIO3_IO28 0x0001b099
+			MX6QDL_PAD_EIM_D29__GPIO3_IO29 0x0001b099
+
+			MX6QDL_PAD_KEY_COL0__GPIO4_IO06 0x0001b099
+			MX6QDL_PAD_KEY_ROW0__GPIO4_IO07 0x0001b099
+			MX6QDL_PAD_KEY_COL1__GPIO4_IO08 0x0001b099
+			MX6QDL_PAD_KEY_ROW1__GPIO4_IO09 0x0001b099
+
+			MX6QDL_PAD_CSI0_PIXCLK__GPIO5_IO18 0x0001b099
+			MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20 0x0001b099
+			MX6QDL_PAD_CSI0_VSYNC__GPIO5_IO21 0x0001b099
+
+			MX6QDL_PAD_NANDF_ALE__GPIO6_IO08 0x0001b099
+			MX6QDL_PAD_NANDF_CS1__GPIO6_IO14 0x0001b099
+		>;
+	};
+
+	pinctrl_pcie: pciegrp {
+		fsl,pins = <
+			/* HYS = 1, DSE = 110, 100k up, SPEED = HIGH (11)*/
+			MX6QDL_PAD_SD4_DAT3__GPIO2_IO11 0x001b0f0 /* #PCIE.WAKE */
+			MX6QDL_PAD_NANDF_CLE__GPIO6_IO07 0x001b0f0 /* #PCIE.RST */
+			MX6QDL_PAD_NANDF_CS0__GPIO6_IO11 0x001b0f0 /* #PCIE.DIS */
+		>;
+	};
+
+	pinctrl_pwm1: pwm1grp {
+		fsl,pins = <
+			/* 100 k PD, DSE 120 OHM, SPPEED LO */
+			MX6QDL_PAD_GPIO_9__PWM1_OUT 0x00003050
+		>;
+	};
+
+	pinctrl_pwm3: pwm3grp {
+		fsl,pins = <
+			/* 100 k PD, DSE 120 OHM, SPPEED LO */
+			MX6QDL_PAD_SD4_DAT1__PWM3_OUT 0x00003050
+		>;
+	};
+
+	pinctrl_pwm4: pwm4grp {
+		fsl,pins = <
+			/* 100 k PD, DSE 120 OHM, SPPEED LO */
+			MX6QDL_PAD_SD4_DAT2__PWM4_OUT 0x00003050
+		>;
+	};
+
+	pinctrl_regpcie: regpciegrp {
+		fsl,pins = <
+			/* HYS = 1, DSE = 110, PUE+PKE, SPEED = HIGH (11)*/
+			MX6QDL_PAD_NANDF_D0__GPIO2_IO00 0x00130f0 /* PCIE.PWR_EN */
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD4_DAT4__UART2_RX_DATA 0x1b099
+			MX6QDL_PAD_SD4_DAT7__UART2_TX_DATA 0x1b099
+		>;
+	};
+
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD4_CLK__UART3_RX_DATA 0x1b0b1
+			MX6QDL_PAD_SD4_CMD__UART3_TX_DATA 0x1b0b1
+			MX6QDL_PAD_EIM_D30__UART3_CTS_B   0x1b0b1
+			MX6QDL_PAD_EIM_D31__UART3_RTS_B   0x1b0b1
+		>;
+	};
+
+	pinctrl_uart4: uart4grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT12__UART4_TX_DATA 0x1b0b1
+			MX6QDL_PAD_CSI0_DAT13__UART4_RX_DATA 0x1b0b1
+			MX6QDL_PAD_CSI0_DAT16__UART4_RTS_B 0x1b0b1
+			MX6QDL_PAD_CSI0_DAT17__UART4_CTS_B 0x1b0b1
+		>;
+	};
+
+	pinctrl_uart5: uart5grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT14__UART5_TX_DATA 0x1b0b1
+			MX6QDL_PAD_CSI0_DAT15__UART5_RX_DATA 0x1b0b1
+			MX6QDL_PAD_CSI0_DAT18__UART5_RTS_B 0x1b0b1
+			MX6QDL_PAD_CSI0_DAT19__UART5_CTS_B 0x1b0b1
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			/* CLK: 47k Pup SPD_LOW DSE 40Ohm SRE_FAST HYS */
+			MX6QDL_PAD_SD2_CLK__SD2_CLK    0x00017071
+			/* SD2: 47k Pup SPD_LOW DSE 80Ohm SRE_FAST HYS */
+			MX6QDL_PAD_SD2_CMD__SD2_CMD    0x00017059
+			MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x00017059
+			MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x00017059
+			MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x00017059
+			MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x00017059
+
+			MX6QDL_PAD_GPIO_4__GPIO1_IO04  0x0001b099 /* usdhc2 CD */
+			MX6QDL_PAD_GPIO_2__GPIO1_IO02  0x0001b099 /* usdhc2 WP */
+		>;
+	};
+
+	pinctrl_usbotg: usbotggrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D21__USB_OTG_OC  0x0001b0b0
+			MX6QDL_PAD_GPIO_1__USB_OTG_ID   0x00017059
+			MX6QDL_PAD_EIM_D22__USB_OTG_PWR 0x0001b099
+		>;
+	};
+
+	pinctrl_wdog1: wdog1grp {
+		fsl,pins = <
+			 /* Watchdog out */
+			MX6QDL_PAD_SD1_DAT2__WDOG1_B 0x0000b099
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6qdl-mba6a.dtsi b/arch/arm/boot/dts/imx6qdl-mba6a.dtsi
new file mode 100644
index 000000000000..df8fa169e9f6
--- /dev/null
+++ b/arch/arm/boot/dts/imx6qdl-mba6a.dtsi
@@ -0,0 +1,30 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright 2013 Sascha Hauer, Pengutronix
+ *
+ * Copyright 2013-2021 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet>, <&pinctrl_enet_fix>;
+};
+
+&i2c1 {
+	lm75: temperature-sensor@49 {
+		compatible = "national,lm75";
+		reg = <0x49>;
+	};
+
+	m24c64_57: eeprom@57 {
+		compatible = "atmel,24c64";
+		reg = <0x57>;
+		pagesize = <32>;
+	};
+
+	rtc0: rtc@68 {
+		compatible = "dallas,ds1339";
+		reg = <0x68>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6qdl-mba6b.dtsi b/arch/arm/boot/dts/imx6qdl-mba6b.dtsi
new file mode 100644
index 000000000000..7d1cd7454c7f
--- /dev/null
+++ b/arch/arm/boot/dts/imx6qdl-mba6b.dtsi
@@ -0,0 +1,49 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright 2013 Sascha Hauer, Pengutronix
+ *
+ * Copyright 2013-2021 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet>;
+};
+
+&i2c1 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	pinctrl-1 = <&pinctrl_i2c1_recovery>;
+	scl-gpios = <&gpio5 27 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio5 26 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "okay";
+};
+
+&i2c3 {
+	lm75: temperature-sensor@49 {
+		compatible = "national,lm75";
+		reg = <0x49>;
+	};
+
+	m24c64_57: eeprom@57 {
+		compatible = "atmel,24c64";
+		reg = <0x57>;
+		pagesize = <32>;
+	};
+
+	rtc0: rtc@68 {
+		compatible = "dallas,ds1339";
+		reg = <0x68>;
+	};
+};
+
+&iomuxc {
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001b899
+			MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001b899
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6qdl-nit6xlite.dtsi b/arch/arm/boot/dts/imx6qdl-nit6xlite.dtsi
index ac34709e9741..a53a5d0766a5 100644
--- a/arch/arm/boot/dts/imx6qdl-nit6xlite.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-nit6xlite.dtsi
@@ -179,7 +179,7 @@
 	pinctrl-0 = <&pinctrl_ecspi1>;
 	status = "okay";
 
-	flash: m25p80@0 {
+	flash: flash@0 {
 		compatible = "microchip,sst25vf016b";
 		spi-max-frequency = <20000000>;
 		reg = <0>;
@@ -192,6 +192,7 @@
 	phy-mode = "rgmii";
 	phy-handle = <&ethphy>;
 	phy-reset-gpios = <&gpio1 27 GPIO_ACTIVE_LOW>;
+	/delete-property/ interrupts;
 	interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
 			      <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
 	fsl,err006687-workaround-present;
diff --git a/arch/arm/boot/dts/imx6qdl-nitrogen6_max.dtsi b/arch/arm/boot/dts/imx6qdl-nitrogen6_max.dtsi
index c96f4d7e1e0d..57c21a01f126 100644
--- a/arch/arm/boot/dts/imx6qdl-nitrogen6_max.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-nitrogen6_max.dtsi
@@ -321,7 +321,7 @@
 	pinctrl-0 = <&pinctrl_ecspi1>;
 	status = "okay";
 
-	flash: m25p80@0 {
+	flash: flash@0 {
 		compatible = "microchip,sst25vf016b";
 		spi-max-frequency = <20000000>;
 		reg = <0>;
@@ -334,6 +334,7 @@
 	phy-mode = "rgmii";
 	phy-handle = <&ethphy>;
 	phy-reset-gpios = <&gpio1 27 GPIO_ACTIVE_LOW>;
+	/delete-property/ interrupts;
 	interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
 			      <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
 	fsl,err006687-workaround-present;
diff --git a/arch/arm/boot/dts/imx6qdl-nitrogen6_som2.dtsi b/arch/arm/boot/dts/imx6qdl-nitrogen6_som2.dtsi
index 92d09a3ebe0e..000e9dc97b1a 100644
--- a/arch/arm/boot/dts/imx6qdl-nitrogen6_som2.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-nitrogen6_som2.dtsi
@@ -252,7 +252,7 @@
 	pinctrl-0 = <&pinctrl_ecspi1>;
 	status = "okay";
 
-	flash: m25p80@0 {
+	flash: flash@0 {
 		compatible = "microchip,sst25vf016b";
 		spi-max-frequency = <20000000>;
 		reg = <0>;
@@ -263,6 +263,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
 	phy-mode = "rgmii";
+	/delete-property/ interrupts;
 	interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
 			      <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
 	fsl,err006687-workaround-present;
diff --git a/arch/arm/boot/dts/imx6qdl-nitrogen6x.dtsi b/arch/arm/boot/dts/imx6qdl-nitrogen6x.dtsi
index 49da30d7510c..731759bdd7f5 100644
--- a/arch/arm/boot/dts/imx6qdl-nitrogen6x.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-nitrogen6x.dtsi
@@ -237,7 +237,7 @@
 	pinctrl-0 = <&pinctrl_ecspi1>;
 	status = "okay";
 
-	flash: m25p80@0 {
+	flash: flash@0 {
 		compatible = "sst,sst25vf016b", "jedec,spi-nor";
 		spi-max-frequency = <20000000>;
 		reg = <0>;
@@ -267,6 +267,7 @@
 	phy-mode = "rgmii";
 	phy-handle = <&ethphy>;
 	phy-reset-gpios = <&gpio1 27 GPIO_ACTIVE_LOW>;
+	/delete-property/ interrupts;
 	interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
 			      <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
 	fsl,err006687-workaround-present;
diff --git a/arch/arm/boot/dts/imx6qdl-phytec-mira-peb-av-02.dtsi b/arch/arm/boot/dts/imx6qdl-phytec-mira-peb-av-02.dtsi
new file mode 100644
index 000000000000..0020dbb1722c
--- /dev/null
+++ b/arch/arm/boot/dts/imx6qdl-phytec-mira-peb-av-02.dtsi
@@ -0,0 +1,119 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2018 PHYTEC Messtechnik
+ * Author: Christian Hemp <c.hemp@phytec.de>
+ */
+
+/ {
+	display: display0 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "fsl,imx-parallel-display";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_disp0>;
+		interface-pix-fmt = "rgb24";
+		status = "disabled";
+
+		port@0 {
+			reg = <0>;
+
+			display0_in: endpoint {
+				remote-endpoint = <&ipu1_di0_disp0>;
+			};
+		};
+
+		port@1 {
+			reg = <1>;
+
+			display0_out: endpoint {
+				remote-endpoint = <&peb_panel_lcd_in>;
+			};
+		};
+	};
+
+	panel-lcd {
+		compatible = "edt,etm0700g0edh6";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_disp0_pwr>;
+		power-supply = <&reg_display>;
+		enable-gpios = <&gpio3 22 GPIO_ACTIVE_HIGH>;
+		backlight = <&backlight>;
+		status = "disabled";
+
+		port {
+			peb_panel_lcd_in: endpoint {
+				remote-endpoint = <&display0_out>;
+			};
+		};
+	};
+
+	reg_display: regulator-peb-display {
+		compatible = "regulator-fixed";
+		regulator-name = "peb-display";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+};
+
+&i2c1 {
+	edt_ft5x06: touchscreen@38 {
+		compatible = "edt,edt-ft5406";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_edt_ft5x06>;
+		reg = <0x38>;
+		interrupt-parent = <&gpio3>;
+		interrupts = <2 IRQ_TYPE_NONE>;
+		status = "disabled";
+	};
+};
+
+&ipu1_di0_disp0 {
+	remote-endpoint = <&display0_in>;
+};
+
+&iomuxc {
+	pinctrl_disp0: disp0grp {
+		fsl,pins = <
+			MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK	0x10
+			MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02		0x10
+			MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03		0x10
+			MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15		0x1b080
+			MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00	0x10
+			MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01	0x10
+			MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02	0x10
+			MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03	0x10
+			MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04	0x10
+			MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05	0x10
+			MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06	0x10
+			MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07	0x10
+			MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08	0x10
+			MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09	0x10
+			MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10	0x10
+			MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11	0x10
+			MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12	0x10
+			MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13	0x10
+			MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14	0x10
+			MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15	0x10
+			MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16	0x10
+			MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17	0x10
+			MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18	0x10
+			MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19	0x10
+			MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20	0x10
+			MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21	0x10
+			MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22	0x10
+			MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23	0x10
+		>;
+	};
+
+	pinctrl_disp0_pwr: disp0pwrgrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D22__GPIO3_IO22			0x1b0b0
+		>;
+	};
+
+	pinctrl_edt_ft5x06: edtft5x06grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_DA2__GPIO3_IO02			0xb0b1
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6qdl-phytec-mira-peb-eval-01.dtsi b/arch/arm/boot/dts/imx6qdl-phytec-mira-peb-eval-01.dtsi
new file mode 100644
index 000000000000..037b60197598
--- /dev/null
+++ b/arch/arm/boot/dts/imx6qdl-phytec-mira-peb-eval-01.dtsi
@@ -0,0 +1,71 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2018 PHYTEC Messtechnik
+ * Author: Christian Hemp <c.hemp@phytec.de>
+ */
+
+#include <dt-bindings/input/input.h>
+
+/ {
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_keys>;
+		status = "disabled";
+
+		power {
+			label = "Power Button";
+			gpios = <&gpio5 28 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_WAKEUP>;
+			wakeup-source;
+		};
+
+		sleep {
+			label = "Sleep Button";
+			gpios = <&gpio6 18 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_SLEEP>;
+		};
+	};
+
+	user_leds: user-leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_user_leds>;
+		status = "disabled";
+
+		user-led1 {
+			gpios = <&gpio7 1 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "gpio";
+			default-state = "on";
+		};
+
+		user-led2 {
+			gpios = <&gpio7 0 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "gpio";
+			default-state = "on";
+		};
+
+		user-led3 {
+			gpios = <&gpio5 29 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "gpio";
+			default-state = "on";
+		};
+	};
+};
+
+&iomuxc {
+	pinctrl_gpio_keys: gpiokeysgrp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_DAT6__GPIO6_IO18		0x1b0b0
+			MX6QDL_PAD_CSI0_DAT10__GPIO5_IO28	0x1b0b0
+		>;
+	};
+
+	pinctrl_user_leds: userledsgrp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_DAT4__GPIO7_IO01		0x1b0b0
+			MX6QDL_PAD_SD3_DAT5__GPIO7_IO00		0x1b0b0
+			MX6QDL_PAD_CSI0_DAT11__GPIO5_IO29	0x1b0b0
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6qdl-phytec-mira-peb-wlbt-05.dtsi b/arch/arm/boot/dts/imx6qdl-phytec-mira-peb-wlbt-05.dtsi
new file mode 100644
index 000000000000..84f884d6e55b
--- /dev/null
+++ b/arch/arm/boot/dts/imx6qdl-phytec-mira-peb-wlbt-05.dtsi
@@ -0,0 +1,85 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2021 PHYTEC Messtechnik GmbH
+ * Author: Yunus Bas <y.bas@phytec.de>
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	reg_wl_en: regulator-wl-en {
+		compatible = "regulator-fixed";
+		regulator-name = "wlan_en";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_wl>;
+		gpio = <&gpio5 2 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		startup-delay-us = <100>;
+		status = "disabled";
+	};
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3_bt>;
+	uart-has-rtscts;
+
+	bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		shutdown-gpios = <&gpio7 0 GPIO_ACTIVE_HIGH>;
+		device-wakeup-gpios = <&gpio7 1 GPIO_ACTIVE_HIGH>;
+		host-wakeup-gpios = <&gpio5 26 GPIO_ACTIVE_HIGH>;
+		status = "disabled";
+	};
+};
+
+&usdhc3 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc3_wl>;
+	vmmc-supply = <&reg_wl_en>;
+	bus-width = <4>;
+	non-removable;
+	no-1-8-v;
+	status = "disabled";
+
+	brmcf: wifi@1 {
+		compatible = "brcm,bcm4329-fmac";
+		reg = <1>;
+	};
+};
+
+&iomuxc {
+	pinctrl_uart3_bt: uart3grp-bt {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D25__UART3_RX_DATA	0x1b0b1
+			MX6QDL_PAD_EIM_D24__UART3_TX_DATA	0x1b0b1
+			MX6QDL_PAD_EIM_EB3__UART3_RTS_B		0x1b0b1
+			MX6QDL_PAD_EIM_D23__UART3_CTS_B		0x1b0b1
+			MX6QDL_PAD_SD3_DAT5__GPIO7_IO00		0xb0b1	/* BT ENABLE */
+			MX6QDL_PAD_SD3_DAT4__GPIO7_IO01		0xb0b1	/* DEV WAKEUP */
+			MX6QDL_PAD_CSI0_DAT8__GPIO5_IO26	0xb0b1  /* HOST WAKEUP */
+		>;
+	};
+
+	pinctrl_usdhc3_wl: usdhc3grp-wl {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_CMD__SD3_CMD		0x17059
+			MX6QDL_PAD_SD3_CLK__SD3_CLK		0x10059
+			MX6QDL_PAD_SD3_DAT0__SD3_DATA0		0x17059
+			MX6QDL_PAD_SD3_DAT1__SD3_DATA1		0x17059
+			MX6QDL_PAD_SD3_DAT2__SD3_DATA2		0x17059
+			MX6QDL_PAD_SD3_DAT3__SD3_DATA3		0x17059
+		>;
+	};
+
+	pinctrl_wl: wlgrp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_A25__GPIO5_IO02      0xb0b1	/* WLAN ENABLE */
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6qdl-phytec-pfla02.dtsi b/arch/arm/boot/dts/imx6qdl-phytec-pfla02.dtsi
index f3236204cb5a..768bc0e3a2b3 100644
--- a/arch/arm/boot/dts/imx6qdl-phytec-pfla02.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-phytec-pfla02.dtsi
@@ -47,12 +47,12 @@
 		pinctrl-0 = <&pinctrl_leds>;
 		compatible = "gpio-leds";
 
-		green {
+		led_green: green {
 			label = "phyflex:green";
 			gpios = <&gpio1 30 0>;
 		};
 
-		red {
+		led_red: red {
 			label = "phyflex:red";
 			gpios = <&gpio2 31 0>;
 		};
@@ -205,6 +205,19 @@
 				regulator-always-on;
 			};
 		};
+
+		da9063_rtc: rtc {
+			compatible = "dlg,da9063-rtc";
+		};
+
+		da9063_wdog: watchdog {
+			compatible = "dlg,da9063-watchdog";
+		};
+
+		onkey {
+			compatible = "dlg,da9063-onkey";
+			status = "disabled";
+		};
 	};
 };
 
diff --git a/arch/arm/boot/dts/imx6qdl-phytec-phycore-som.dtsi b/arch/arm/boot/dts/imx6qdl-phytec-phycore-som.dtsi
index 94b254bfd054..28a805384668 100644
--- a/arch/arm/boot/dts/imx6qdl-phytec-phycore-som.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-phytec-phycore-som.dtsi
@@ -116,6 +116,16 @@
 			dlg,use-sw-pm;
 		};
 
+		thermal {
+			compatible = "dlg,da9062-thermal";
+			status = "disabled";
+		};
+
+		gpio {
+			compatible = "dlg,da9062-gpio";
+			status = "disabled";
+		};
+
 		regulators {
 			vdd_arm: buck1 {
 				regulator-name = "vdd_arm";
diff --git a/arch/arm/boot/dts/imx6qdl-prti6q.dtsi b/arch/arm/boot/dts/imx6qdl-prti6q.dtsi
index 19578f660b09..f0db0d4471f4 100644
--- a/arch/arm/boot/dts/imx6qdl-prti6q.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-prti6q.dtsi
@@ -94,6 +94,9 @@
 	pinctrl-0 = <&pinctrl_usdhc3>;
 	bus-width = <8>;
 	non-removable;
+	no-1-8-v;
+	no-sd;
+	no-sdio;
 	status = "okay";
 };
 
diff --git a/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi b/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi
index 5e58740d40c5..3dbb460ef102 100644
--- a/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi
@@ -272,7 +272,7 @@
 	pinctrl-0 = <&pinctrl_ecspi1 &pinctrl_ecspi1_cs>;
 	status = "disabled"; /* pin conflict with WEIM NOR */
 
-	flash: m25p80@0 {
+	flash: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "st,m25p32", "jedec,spi-nor";
@@ -295,6 +295,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
 	phy-mode = "rgmii-id";
+	/delete-property/ interrupts;
 	interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
 			      <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
 	fsl,err006687-workaround-present;
diff --git a/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi b/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi
index eb9a0b104f1c..22f8e2783cdf 100644
--- a/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi
@@ -1,43 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0 OR X11
 /*
  * Copyright 2011 Freescale Semiconductor, Inc.
  * Copyright 2011 Linaro Ltd.
  *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License
- *     version 2 as published by the Free Software Foundation.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
  */
 
 #include <dt-bindings/clock/imx6qdl-clock.h>
@@ -313,7 +278,7 @@
 	pinctrl-0 = <&pinctrl_ecspi1>;
 	status = "okay";
 
-	flash: m25p80@0 {
+	flash: flash@0 {
 		compatible = "sst,sst25vf016b", "jedec,spi-nor";
 		spi-max-frequency = <20000000>;
 		reg = <0>;
diff --git a/arch/arm/boot/dts/imx6qdl-sabresd.dtsi b/arch/arm/boot/dts/imx6qdl-sabresd.dtsi
index 0c0105468a2f..37482a9023fc 100644
--- a/arch/arm/boot/dts/imx6qdl-sabresd.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-sabresd.dtsi
@@ -197,7 +197,7 @@
 	pinctrl-0 = <&pinctrl_ecspi1>;
 	status = "okay";
 
-	flash: m25p80@0 {
+	flash: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "st,m25p32", "jedec,spi-nor";
diff --git a/arch/arm/boot/dts/imx6qdl-skov-cpu-revc.dtsi b/arch/arm/boot/dts/imx6qdl-skov-cpu-revc.dtsi
index 69ae430a53bd..b81799d7076a 100644
--- a/arch/arm/boot/dts/imx6qdl-skov-cpu-revc.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-skov-cpu-revc.dtsi
@@ -2,35 +2,60 @@
 //
 // Copyright (C) 2020 Pengutronix, Ulrich Oelmann <kernel@pengutronix.de>
 
+/ {
+	touchscreen {
+		compatible = "resistive-adc-touch";
+		io-channels = <&adc_ts 1>, <&adc_ts 3>, <&adc_ts 4>, <&adc_ts 5>;
+		io-channel-names = "y", "z1", "z2", "x";
+		touchscreen-min-pressure = <65000>;
+		touchscreen-inverted-y;
+		touchscreen-swapped-x-y;
+		touchscreen-x-plate-ohms = <300>;
+		touchscreen-y-plate-ohms = <800>;
+	};
+};
+
 &ecspi4 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_ecspi4>;
 	cs-gpios = <&gpio3 20 GPIO_ACTIVE_LOW>;
 	status = "okay";
 
-	touchscreen@0 {
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_touch>;
-		compatible = "ti,tsc2046";
+	adc_ts: adc@0 {
+		compatible = "ti,tsc2046e-adc";
 		reg = <0>;
+		pinctrl-0 = <&pinctrl_touch>;
+		pinctrl-names ="default";
 		spi-max-frequency = <1000000>;
 		interrupts-extended = <&gpio3 19 IRQ_TYPE_LEVEL_LOW>;
-		vcc-supply  = <&reg_3v3>;
-		pendown-gpio = <&gpio3 19 GPIO_ACTIVE_LOW>;
-		ti,x-plate-ohms = /bits/ 16 <850>;
-		ti,y-plate-ohms = /bits/ 16 <295>;
-		ti,pressure-min = /bits/ 16 <2>;
-		ti,pressure-max = /bits/ 16 <1500>;
-		ti,vref-mv	= /bits/ 16 <3300>;
-		ti,settle-delay-usec = /bits/ 16 <15>;
-		ti,vref-delay-usecs = /bits/ 16 <0>;
-		ti,penirq-recheck-delay-usecs = /bits/ 16 <100>;
-		ti,debounce-max = /bits/ 16 <100>;
-		ti,debounce-tol = /bits/ 16 <(~0)>;
-		ti,debounce-rep = /bits/ 16 <4>;
-		touchscreen-swapped-x-y;
-		touchscreen-inverted-y;
-		wakeup-source;
+		#io-channel-cells = <1>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		channel@1 {
+			reg = <1>;
+			settling-time-us = <700>;
+			oversampling-ratio = <5>;
+		};
+
+		channel@3 {
+			reg = <3>;
+			settling-time-us = <700>;
+			oversampling-ratio = <5>;
+		};
+
+		channel@4 {
+			reg = <4>;
+			settling-time-us = <700>;
+			oversampling-ratio = <5>;
+		};
+
+		channel@5 {
+			reg = <5>;
+			settling-time-us = <700>;
+			oversampling-ratio = <5>;
+		};
 	};
 };
 
diff --git a/arch/arm/boot/dts/imx6qdl-skov-cpu.dtsi b/arch/arm/boot/dts/imx6qdl-skov-cpu.dtsi
index 77a91a97e6cf..3def1b621c8e 100644
--- a/arch/arm/boot/dts/imx6qdl-skov-cpu.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-skov-cpu.dtsi
@@ -149,6 +149,16 @@
 		gpio = <&gpio4 11 GPIO_ACTIVE_LOW>;
 	};
 
+	reg_tft_vcom: regulator-tft-vcom {
+		compatible = "pwm-regulator";
+		pwms = <&pwm3 0 20000 0>;
+		regulator-name = "tft_vcom";
+		regulator-min-microvolt = <3600000>;
+		regulator-max-microvolt = <3600000>;
+		regulator-always-on;
+		voltage-table = <3600000 26>;
+	};
+
 	reg_vcc_mmc: regulator-vcc-mmc {
 		compatible = "regulator-fixed";
 		pinctrl-names = "default";
diff --git a/arch/arm/boot/dts/imx6qdl-sr-som.dtsi b/arch/arm/boot/dts/imx6qdl-sr-som.dtsi
index f86efd0ccc40..ce543e325cd3 100644
--- a/arch/arm/boot/dts/imx6qdl-sr-som.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-sr-som.dtsi
@@ -83,6 +83,16 @@
 			qca,clk-out-frequency = <125000000>;
 			qca,smarteee-tw-us-1g = <24>;
 		};
+
+		/*
+		 * ADIN1300 (som rev 1.9 or later) is always at address 1. It
+		 * will be enabled automatically by U-Boot if detected.
+		 */
+		ethernet-phy@1 {
+			reg = <1>;
+			adi,phy-output-clock = "125mhz-free-running";
+			status = "disabled";
+		};
 	};
 };
 
diff --git a/arch/arm/boot/dts/imx6qdl-tqma6.dtsi b/arch/arm/boot/dts/imx6qdl-tqma6.dtsi
index 51a3a5392c95..344ea935c7da 100644
--- a/arch/arm/boot/dts/imx6qdl-tqma6.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-tqma6.dtsi
@@ -52,6 +52,13 @@
 		>;
 	};
 
+	pinctrl_i2c1_recovery: i2c1recoverygrp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT8__GPIO5_IO26 0x4001b899
+			MX6QDL_PAD_CSI0_DAT9__GPIO5_IO27 0x4001b899
+		>;
+	};
+
 	pinctrl_i2c3: i2c3grp {
 		fsl,pins = <
 			MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b899
@@ -59,6 +66,13 @@
 		>;
 	};
 
+	pinctrl_i2c3_recovery: i2c3recoverygrp {
+		fsl,pins = <
+			MX6QDL_PAD_GPIO_5__GPIO1_IO05 0x4001b899
+			MX6QDL_PAD_GPIO_6__GPIO1_IO06 0x4001b899
+		>;
+	};
+
 	pinctrl_pmic: pmicgrp {
 		fsl,pins = <
 			MX6QDL_PAD_NANDF_RB0__GPIO6_IO10 0x1b099 /* PMIC irq */
diff --git a/arch/arm/boot/dts/imx6qdl-tqma6a.dtsi b/arch/arm/boot/dts/imx6qdl-tqma6a.dtsi
index b679bec78e6c..aff46f3040c1 100644
--- a/arch/arm/boot/dts/imx6qdl-tqma6a.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-tqma6a.dtsi
@@ -4,9 +4,21 @@
  * Copyright 2013-2017 Markus Niebel <Markus.Niebel@tq-group.com>
  */
 
+#include <dt-bindings/gpio/gpio.h>
+
+&fec {
+	/delete-property/ interrupts;
+	interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
+			      <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
+	fsl,err006687-workaround-present;
+};
+
 &i2c1 {
-	pinctrl-names = "default";
+	pinctrl-names = "default", "gpio";
 	pinctrl-0 = <&pinctrl_i2c1>;
+	pinctrl-1 = <&pinctrl_i2c1_recovery>;
+	scl-gpios = <&gpio5 27 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio5 26 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 	clock-frequency = <100000>;
 	status = "okay";
 
@@ -24,5 +36,20 @@
 		compatible = "st,24c64", "atmel,24c64";
 		reg = <0x50>;
 		pagesize = <32>;
+		vcc-supply = <&reg_3p3v>;
+	};
+};
+
+&iomuxc {
+	/*
+	 * This pinmuxing is required for the ERR006687 workaround. Board
+	 * DTS files that enable the FEC controller with
+	 * fsl,err006687-workaround-present must include this group.
+	 */
+	pinctrl_enet_fix: enetfixgrp {
+		fsl,pins = <
+			/* ENET ping patch */
+			MX6QDL_PAD_GPIO_6__ENET_IRQ 0x000b1
+		>;
 	};
 };
diff --git a/arch/arm/boot/dts/imx6qdl-tqma6b.dtsi b/arch/arm/boot/dts/imx6qdl-tqma6b.dtsi
index 49c472285c06..a3f6543c3aaa 100644
--- a/arch/arm/boot/dts/imx6qdl-tqma6b.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-tqma6b.dtsi
@@ -4,9 +4,14 @@
  * Copyright 2013-2017 Markus Niebel <Markus.Niebel@tq-group.com>
  */
 
+#include <dt-bindings/gpio/gpio.h>
+
 &i2c3 {
-	pinctrl-names = "default";
+	pinctrl-names = "default", "gpio";
 	pinctrl-0 = <&pinctrl_i2c3>;
+	pinctrl-1 = <&pinctrl_i2c3_recovery>;
+	scl-gpios = <&gpio1 5 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio1 6 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 	clock-frequency = <100000>;
 	status = "okay";
 
@@ -24,5 +29,6 @@
 		compatible = "st,24c64", "atmel,24c64";
 		reg = <0x50>;
 		pagesize = <32>;
+		vcc-supply = <&reg_3p3v>;
 	};
 };
diff --git a/arch/arm/boot/dts/imx6qdl-ts7970.dtsi b/arch/arm/boot/dts/imx6qdl-ts7970.dtsi
index fded07f370b3..c096d25a6f5b 100644
--- a/arch/arm/boot/dts/imx6qdl-ts7970.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-ts7970.dtsi
@@ -192,6 +192,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
 	phy-mode = "rgmii";
+	/delete-property/ interrupts;
 	interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
 			      <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
 	fsl,err006687-workaround-present;
@@ -226,7 +227,7 @@
 		reg = <0x28>;
 		#gpio-cells = <2>;
 		gpio-controller;
-		ngpio = <32>;
+		ngpios = <62>;
 	};
 
 	sgtl5000: codec@a {
diff --git a/arch/arm/boot/dts/imx6qdl-tx6-mb7.dtsi b/arch/arm/boot/dts/imx6qdl-tx6-mb7.dtsi
index 410972e1dca9..99ec7a838f8d 100644
--- a/arch/arm/boot/dts/imx6qdl-tx6-mb7.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-tx6-mb7.dtsi
@@ -85,7 +85,7 @@
 };
 
 &i2c3 {
-	rtc: mcp7940x@6f {
+	rtc: rtc@6f {
 		compatible = "microchip,mcp7940x";
 		reg = <0x6f>;
 	};
diff --git a/arch/arm/boot/dts/imx6qdl-tx6.dtsi b/arch/arm/boot/dts/imx6qdl-tx6.dtsi
index 362e65ccaa78..f41f86a76ea9 100644
--- a/arch/arm/boot/dts/imx6qdl-tx6.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-tx6.dtsi
@@ -259,28 +259,11 @@
 		&gpio3 19 GPIO_ACTIVE_HIGH
 	>;
 	status = "disabled";
-
-	spidev0: spi@0 {
-		compatible = "spidev";
-		reg = <0>;
-		spi-max-frequency = <54000000>;
-	};
-
-	spidev1: spi@1 {
-		compatible = "spidev";
-		reg = <1>;
-		spi-max-frequency = <54000000>;
-	};
 };
 
 &fec {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet &pinctrl_enet_mdio &pinctrl_etnphy_rst>;
-	clocks = <&clks IMX6QDL_CLK_ENET>,
-		 <&clks IMX6QDL_CLK_ENET>,
-		 <&clks IMX6QDL_CLK_ENET_REF>,
-		 <&clks IMX6QDL_CLK_ENET_REF>;
-	clock-names = "ipg", "ahb", "ptp", "enet_out";
 	phy-mode = "rmii";
 	phy-reset-gpios = <&gpio7 6 GPIO_ACTIVE_LOW>;
 	phy-reset-post-delay = <10>;
diff --git a/arch/arm/boot/dts/imx6qdl-udoo.dtsi b/arch/arm/boot/dts/imx6qdl-udoo.dtsi
index d07d8f83456d..93a8123da27d 100644
--- a/arch/arm/boot/dts/imx6qdl-udoo.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-udoo.dtsi
@@ -5,6 +5,8 @@
  * Author: Fabio Estevam <fabio.estevam@freescale.com>
  */
 
+#include <dt-bindings/gpio/gpio.h>
+
 / {
 	aliases {
 		backlight = &backlight;
@@ -226,6 +228,7 @@
 				MX6QDL_PAD_SD3_DAT1__SD3_DATA1		0x17059
 				MX6QDL_PAD_SD3_DAT2__SD3_DATA2		0x17059
 				MX6QDL_PAD_SD3_DAT3__SD3_DATA3		0x17059
+				MX6QDL_PAD_SD3_DAT5__GPIO7_IO00		0x1b0b0
 			>;
 		};
 
@@ -292,7 +295,7 @@
 	pinctrl-0 = <&pinctrl_usbh>;
 	vbus-supply = <&reg_usb_h1_vbus>;
 	clocks = <&clks IMX6QDL_CLK_CKO>;
-	status = "okay";
+	status = "disabled";
 };
 
 &usbotg {
@@ -304,7 +307,7 @@
 &usdhc3 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usdhc3>;
-	non-removable;
+	cd-gpios = <&gpio7 0 GPIO_ACTIVE_LOW>;
 	status = "okay";
 };
 
diff --git a/arch/arm/boot/dts/imx6qdl-vicut1-12inch.dtsi b/arch/arm/boot/dts/imx6qdl-vicut1-12inch.dtsi
new file mode 100644
index 000000000000..f505f2704530
--- /dev/null
+++ b/arch/arm/boot/dts/imx6qdl-vicut1-12inch.dtsi
@@ -0,0 +1,128 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2021 Protonic Holland
+ */
+
+/ {
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpiokeys>;
+		autorepeat;
+
+		power {
+			label = "Power Button";
+			gpios = <&gpio2 23 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_POWER>;
+			wakeup-source;
+		};
+	};
+
+	panel {
+		compatible = "kyo,tcg121xglp";
+		backlight = <&backlight_lcd>;
+		power-supply = <&reg_3v3>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&lvds0_out>;
+			};
+		};
+	};
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet>;
+	phy-mode = "rgmii-id";
+	phy-handle = <&rgmii_phy>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* Microchip KSZ9031RNX PHY */
+		rgmii_phy: ethernet-phy@0 {
+			reg = <0>;
+			interrupts-extended = <&gpio1 28 IRQ_TYPE_LEVEL_LOW>;
+			reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <10000>;
+			reset-deassert-us = <300>;
+		};
+	};
+};
+
+&gpio1 {
+	gpio-line-names =
+		"CAN1_TERM", "SD1_CD", "ITU656_RESET", "CAM1_MIRROR",
+			"CAM2_MIRROR", "", "", "SMBALERT",
+		"DEBUG_0", "DEBUG_1", "", "", "", "", "", "",
+		"SD1_DATA0", "SD1_DATA1", "SD1_CMD", "SD1_DATA2", "SD1_CLK",
+			"SD1_DATA3", "ETH_MDIO", "",
+		"", "ETH_RESET", "", "", "ETH_INT", "", "", "ETH_MDC";
+};
+
+&gpio4 {
+	gpio-line-names =
+		"", "", "", "", "", "", "UART4_TXD", "UART4_RXD",
+		"UART5_TXD", "UART5_RXD", "CAN1_TX", "CAN1_RX", "CAN1_SR",
+			"CAN2_SR", "CAN2_TX", "CAN2_RX",
+		"", "", "DIP1_FB", "", "VCAM_EN", "ON1_CTRL", "ON2_CTRL",
+			"HITCH_IN_OUT",
+		"LIGHT_ON", "", "", "CONTACT_IN", "BL_EN", "BL_PWM", "",
+			"ISB_LED";
+};
+
+&gpio5 {
+	gpio-line-names =
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "ITU656_CLK", "I2S_MCLK", "ITU656_PDN", "AUDIO_RESET",
+			"I2S_BITCLK", "I2S_DOUT",
+		"I2S_LRCLK", "I2S_DIN", "I2C1_SDA", "I2C1_SCL", "YACO_AUX_RX",
+			"YACO_AUX_TX", "ITU656_D0", "ITU656_D1";
+};
+
+&gpio6 {
+	gpio-line-names =
+		"ITU656_D2", "ITU656_D3", "ITU656_D4", "ITU656_D5",
+			"ITU656_D6", "ITU656_D7", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "RGMII_TXC", "RGMII_TD0", "RGMII_TD1", "RGMII_TD2",
+			"RGMII_TD3",
+		"RGMII_RX_CTL", "RGMII_RD0", "RGMII_TX_CTL", "RGMII_RD1",
+			"RGMII_RD2", "RGMII_RD3", "", "";
+};
+
+&iomuxc {
+	pinctrl_enet: enetgrp {
+		fsl,pins = <
+			MX6QDL_PAD_RGMII_RXC__RGMII_RXC			0x1b030
+			MX6QDL_PAD_RGMII_RD0__RGMII_RD0			0x1b030
+			MX6QDL_PAD_RGMII_RD1__RGMII_RD1			0x1b030
+			MX6QDL_PAD_RGMII_RD2__RGMII_RD2			0x1b030
+			MX6QDL_PAD_RGMII_RD3__RGMII_RD3			0x1b030
+			MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL		0x1b030
+			MX6QDL_PAD_RGMII_TXC__RGMII_TXC			0x10030
+			MX6QDL_PAD_RGMII_TD0__RGMII_TD0			0x10030
+			MX6QDL_PAD_RGMII_TD1__RGMII_TD1			0x10030
+			MX6QDL_PAD_RGMII_TD2__RGMII_TD2			0x10030
+			MX6QDL_PAD_RGMII_TD3__RGMII_TD3			0x10030
+			MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL		0x10030
+			MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK		0x10030
+			MX6QDL_PAD_ENET_MDIO__ENET_MDIO			0x10030
+			MX6QDL_PAD_ENET_MDC__ENET_MDC			0x10030
+			/* Phy reset */
+			MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25		0x1b0b0
+			MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28		0x1b0b1
+		>;
+	};
+
+	pinctrl_gpiokeys: gpiokeygrp {
+		fsl,pins = <
+			/* nON_SWITCH */
+			MX6QDL_PAD_EIM_CS0__GPIO2_IO23			0x1b0b0
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
index b9e305774fed..c4e6cf0527ba 100644
--- a/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-vicut1.dtsi
@@ -16,18 +16,37 @@
 		stdout-path = &uart4;
 	};
 
-	backlight: backlight {
+	backlight_lcd: backlight {
 		compatible = "pwm-backlight";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_backlight>;
 		pwms = <&pwm1 0 5000000 0>;
 		brightness-levels = <0 16 64 255>;
 		num-interpolated-steps = <16>;
-		default-brightness-level = <1>;
+		default-brightness-level = <48>;
 		power-supply = <&reg_3v3>;
 		enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
 	};
 
+	backlight_led: backlight-led {
+		compatible = "pwm-backlight";
+		pwms = <&pwm3 0 5000000 0>;
+		brightness-levels = <0 16 64 255>;
+		num-interpolated-steps = <16>;
+		default-brightness-level = <48>;
+		power-supply = <&reg_3v3>;
+	};
+
+	/* only for backwards compatibility with old HW */
+	backlight_isb: backlight-isb {
+		compatible = "pwm-backlight";
+		pwms = <&pwm2 0 5000000 0>;
+		brightness-levels = <0 8 48 255>;
+		num-interpolated-steps = <5>;
+		default-brightness-level = <0>;
+		power-supply = <&reg_3v3>;
+	};
+
 	connector {
 		compatible = "composite-video-connector";
 		label = "Composite0";
@@ -61,54 +80,37 @@
 		gpios = <&gpio2 2 GPIO_ACTIVE_LOW>;
 	};
 
-	gpio-keys {
-		compatible = "gpio-keys";
-		autorepeat;
-
-		power {
-			label = "Power Button";
-			gpios = <&gpio2 23 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_POWER>;
-			wakeup-source;
-		};
-	};
-
 	leds {
 		compatible = "gpio-leds";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_leds>;
 
 		led-0 {
-			label = "LED_DI0_DEBUG_0";
+			label = "debug0";
 			function = LED_FUNCTION_HEARTBEAT;
-			gpios = <&gpio4 16 GPIO_ACTIVE_HIGH>;
+			gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
 		};
 
 		led-1 {
-			label = "LED_DI0_DEBUG_1";
+			label = "debug1";
 			function = LED_FUNCTION_DISK;
-			gpios = <&gpio4 17 GPIO_ACTIVE_HIGH>;
+			gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "disk-activity";
 		};
 
 		led-2 {
-			label = "POWER_LED";
+			label = "power_led";
 			function = LED_FUNCTION_POWER;
 			gpios = <&gpio2 24 GPIO_ACTIVE_HIGH>;
 			default-state = "on";
 		};
-	};
-
-	panel {
-		compatible = "kyo,tcg121xglp";
-		backlight = <&backlight>;
-		power-supply = <&reg_3v3>;
 
-		port {
-			panel_in: endpoint {
-				remote-endpoint = <&lvds0_out>;
-			};
+		led-3 {
+			label = "isb_led";
+			function = LED_FUNCTION_POWER;
+			gpios = <&gpio4 31 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
 		};
 	};
 
@@ -126,15 +128,6 @@
 		regulator-max-microvolt = <3300000>;
 	};
 
-	reg_h1_vbus: regulator-h1-vbus {
-		compatible = "regulator-fixed";
-		regulator-name = "h1-vbus";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-		gpio = <&gpio1 0 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-	};
-
 	reg_otg_vbus: regulator-otg-vbus {
 		compatible = "regulator-fixed";
 		regulator-name = "otg-vbus";
@@ -144,18 +137,6 @@
 		enable-active-high;
 	};
 
-	reg_wifi: regulator-wifi {
-		compatible = "regulator-fixed";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_wifi_npd>;
-		regulator-name = "wifi";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <1800000>;
-		gpio = <&gpio1 26 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-		startup-delay-us = <70000>;
-	};
-
 	sound {
 		compatible = "simple-audio-card";
 		simple-audio-card,name = "prti6q-sgtl5000";
@@ -182,6 +163,14 @@
 			frame-master;
 		};
 	};
+
+	thermal-zones {
+		chassis-thermal {
+			polling-delay = <20000>;
+			polling-delay-passive = <0>;
+			thermal-sensors = <&tsens0>;
+		};
+	};
 };
 
 &audmux {
@@ -212,6 +201,8 @@
 &can1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_can1>;
+	termination-gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
+	termination-ohms = <150>;
 	status = "okay";
 };
 
@@ -239,47 +230,13 @@
 	};
 };
 
-&fec {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_enet>;
-	phy-mode = "rgmii-id";
-	phy-handle = <&rgmii_phy>;
-	status = "okay";
-
-	mdio {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		/* Microchip KSZ9031RNX PHY */
-		rgmii_phy: ethernet-phy@0 {
-			reg = <0>;
-			interrupts-extended = <&gpio1 28 IRQ_TYPE_LEVEL_LOW>;
-			reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
-			reset-assert-us = <10000>;
-			reset-deassert-us = <300>;
-		};
-	};
-};
-
-&gpio1 {
-	gpio-line-names =
-		"CAN1_TERM", "SD1_CD", "ITU656_RESET", "CAM1_MIRROR",
-			"CAM2_MIRROR", "", "", "SMBALERT",
-		"DEBUG_0", "DEBUG_1", "SDIO_SCK", "SDIO_CMD", "SDIO_D3",
-			"SDIO_D2", "SDIO_D1", "SDIO_D0",
-		"SD1_DATA0", "SD1_DATA1", "SD1_CMD", "SD1_DATA2", "SD1_CLK",
-			"SD1_DATA3", "", "",
-		"", "ETH_RESET", "WIFI_PD", "WIFI_BT_RST", "ETH_INT", "",
-			"WL_IRQ", "ETH_MDC";
-};
-
 &gpio2 {
 	gpio-line-names =
-		"count0", "count1", "count2", "", "", "", "", "",
-		"REV_ID0", "REV_ID1", "REV_ID2", "REV_ID3", "REV_ID4",
-			"BOARD_ID0", "BOARD_ID1", "BOARD_ID2",
-		"", "", "", "", "", "", "", "ON_SWITCH",
-		"POWER_LED", "", "ECSPI2_SS0", "", "", "", "", "";
+		"YACO_WHEEL", "YACO_RADAR", "YACO_PTO", "", "", "", "", "",
+		"", "LED_PWM", "", "", "",
+			"", "", "",
+		"", "", "", "", "", "ISB_IN2", "ISB_nIN1", "ON_SWITCH",
+		"POWER_LED", "", "", "", "", "", "", "";
 };
 
 &gpio3 {
@@ -288,37 +245,8 @@
 		"", "", "", "", "", "", "", "",
 		"ECSPI1_SCLK", "ECSPI1_MISO", "ECSPI1_MOSI", "ECSPI1_SS1",
 			"CPU_ON1_FB", "USB_OTG_OC", "USB_OTG_PWR", "YACO_IRQ",
-		"", "", "", "", "", "", "", "";
-};
-
-&gpio4 {
-	gpio-line-names =
-		"", "", "", "", "", "", "UART4_TXD", "UART4_RXD",
-		"UART5_TXD", "UART5_RXD", "CAN1_TX", "CAN1_RX", "CAN1_SR",
-			"CAN2_SR", "CAN2_TX", "CAN2_RX",
-		"LED_DI0_DEBUG_0", "LED_DI0_DEBUG_1", "", "", "", "", "", "",
-		"", "", "", "", "BL_EN", "BL_PWM", "", "";
-};
-
-&gpio5 {
-	gpio-line-names =
-		"", "", "", "", "", "PCIE_WAKE", "PCIE_CLKREQ", "PCIE_W_DIS",
-		"PCIE_RESET", "", "", "", "", "", "", "",
-		"", "", "ITU656_CLK", "I2S_MCLK", "ITU656_PDN", "AUDIO_RESET",
-			"I2S_BITCLK", "I2S_DOUT",
-		"I2S_LRCLK", "I2S_DIN", "I2C1_SDA", "I2C1_SCL", "YACO_AUX_RX",
-			"YACO_AUX_TX", "ITU656_D0", "ITU656_D1";
-};
-
-&gpio6 {
-	gpio-line-names =
-		"ITU656_D2", "ITU656_D3", "ITU656_D4", "ITU656_D5",
-			"ITU656_D6", "ITU656_D7", "", "",
-		"", "", "", "", "", "", "", "",
-		"", "", "", "RGMII_TXC", "RGMII_TD0", "RGMII_TD1", "RGMII_TD2",
-			"RGMII_TD3",
-		"RGMII_RX_CTL", "RGMII_RD0", "RGMII_TX_CTL", "RGMII_RD1",
-			"RGMII_RD2", "RGMII_RD3", "", "";
+		"TSS_TXD", "TSS_RXD", "", "", "", "", "YACO_BOOT0",
+			"YACO_RESET";
 };
 
 &gpio7 {
@@ -413,9 +341,10 @@
 		reg = <0x51>;
 	};
 
-	temperature-sensor@70 {
+	tsens0: temperature-sensor@70 {
 		compatible = "ti,tmp103";
 		reg = <0x70>;
+		#thermal-sensor-cells = <0>;
 	};
 };
 
@@ -445,13 +374,21 @@
 	};
 };
 
-&pcie {
+&pwm1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm1>;
 	status = "okay";
 };
 
-&pwm1 {
+&pwm2 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_pwm1>;
+	pinctrl-0 = <&pinctrl_pwm2>;
+	status = "okay";
+};
+
+&pwm3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm3>;
 	status = "okay";
 };
 
@@ -467,12 +404,6 @@
 	status = "okay";
 };
 
-&uart2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart2>;
-	status = "okay";
-};
-
 &uart3 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart3>;
@@ -492,7 +423,6 @@
 };
 
 &usbh1 {
-	vbus-supply = <&reg_h1_vbus>;
 	pinctrl-names = "default";
 	phy_type = "utmi";
 	dr_mode = "host";
@@ -521,26 +451,6 @@
 	status = "okay";
 };
 
-&usdhc2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc2>;
-	vmmc-supply = <&reg_wifi>;
-	non-removable;
-	cap-power-off-card;
-	keep-power-in-suspend;
-	no-1-8-v;
-	no-mmc;
-	no-sd;
-	status = "okay";
-
-	wifi {
-		compatible = "ti,wl1271";
-		interrupts-extended = <&gpio1 30 IRQ_TYPE_LEVEL_HIGH>;
-		ref-clock-frequency = "38400000";
-		tcxo-clock-frequency = "19200000";
-	};
-};
-
 &usdhc3 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usdhc3>;
@@ -621,29 +531,6 @@
 		>;
 	};
 
-	pinctrl_enet: enetgrp {
-		fsl,pins = <
-			MX6QDL_PAD_RGMII_RXC__RGMII_RXC			0x1b030
-			MX6QDL_PAD_RGMII_RD0__RGMII_RD0			0x1b030
-			MX6QDL_PAD_RGMII_RD1__RGMII_RD1			0x1b030
-			MX6QDL_PAD_RGMII_RD2__RGMII_RD2			0x1b030
-			MX6QDL_PAD_RGMII_RD3__RGMII_RD3			0x1b030
-			MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL		0x1b030
-			MX6QDL_PAD_RGMII_TXC__RGMII_TXC			0x10030
-			MX6QDL_PAD_RGMII_TD0__RGMII_TD0			0x10030
-			MX6QDL_PAD_RGMII_TD1__RGMII_TD1			0x10030
-			MX6QDL_PAD_RGMII_TD2__RGMII_TD2			0x10030
-			MX6QDL_PAD_RGMII_TD3__RGMII_TD3			0x10030
-			MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL		0x10030
-			MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK		0x10030
-			MX6QDL_PAD_ENET_MDIO__ENET_MDIO			0x10030
-			MX6QDL_PAD_ENET_MDC__ENET_MDC			0x10030
-			/* Phy reset */
-			MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25		0x1b0b0
-			MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28		0x1b0b1
-		>;
-	};
-
 	pinctrl_hog: hoggrp {
 		fsl,pins = <
 			/* ITU656_nRESET */
@@ -654,8 +541,6 @@
 			MX6QDL_PAD_GPIO_4__GPIO1_IO04			0x130b0
 			/* CAM_nDETECT */
 			MX6QDL_PAD_GPIO_17__GPIO7_IO12			0x1b0b0
-			/* nON_SWITCH */
-			MX6QDL_PAD_EIM_CS0__GPIO2_IO23			0x1b0b0
 			/* ISB_IN1 */
 			MX6QDL_PAD_EIM_A16__GPIO2_IO22			0x130b0
 			/* ISB_nIN2 */
@@ -677,27 +562,11 @@
 			/* ITU656_nPDN */
 			MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20		0x1b0b0
 
-			/* HW revision detect */
-			/* REV_ID0 */
-			MX6QDL_PAD_SD4_DAT0__GPIO2_IO08			0x1b0b0
-			/* REV_ID1 */
-			MX6QDL_PAD_SD4_DAT1__GPIO2_IO09			0x1b0b0
-			/* REV_ID2 */
-			MX6QDL_PAD_SD4_DAT2__GPIO2_IO10			0x1b0b0
-			/* REV_ID3 */
-			MX6QDL_PAD_SD4_DAT3__GPIO2_IO11			0x1b0b0
-			/* REV_ID4 */
-			MX6QDL_PAD_SD4_DAT4__GPIO2_IO12			0x1b0b0
-
 			/* New in HW revision 1 */
 			/* ON1_FB */
 			MX6QDL_PAD_EIM_D20__GPIO3_IO20			0x100b0
 			/* DIP1_FB */
 			MX6QDL_PAD_DI0_PIN2__GPIO4_IO18			0x1b0b0
-
-			/* New in UT2: FIXME: ISB PWM should start off, PD */
-			/* ISB_LED_PWM */
-			MX6QDL_PAD_DISP0_DAT9__GPIO4_IO30		0x130b0
 		>;
 	};
 
@@ -737,6 +606,8 @@
 			MX6QDL_PAD_DI0_PIN15__GPIO4_IO17		0x1b0b0
 			/* POWER_LED */
 			MX6QDL_PAD_EIM_CS1__GPIO2_IO24			0x1b0b0
+			/* ISB_LED */
+			MX6QDL_PAD_DISP0_DAT10__GPIO4_IO31		0x1b0b0
 		>;
 	};
 
@@ -746,20 +617,23 @@
 		>;
 	};
 
-	/* YaCO AUX Uart */
-	pinctrl_uart1: uart1grp {
+	pinctrl_pwm2: pwm2grp {
 		fsl,pins = <
-			MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA		0x1b0b1
-			MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA		0x1b0b1
+			MX6QDL_PAD_DISP0_DAT9__PWM2_OUT			0x1b0b0
 		>;
 	};
 
-	pinctrl_uart2: uart2grp {
+	pinctrl_pwm3: pwm3grp {
 		fsl,pins = <
-			MX6QDL_PAD_EIM_D26__UART2_RX_DATA		0x1b0b1
-			MX6QDL_PAD_EIM_D27__UART2_TX_DATA		0x1b0b1
-			MX6QDL_PAD_EIM_D28__UART2_DTE_CTS_B		0x1b0b1
-			MX6QDL_PAD_EIM_D29__UART2_DTE_RTS_B		0x1b0b1
+			MX6QDL_PAD_SD4_DAT1__PWM3_OUT			0x1b0b0
+		>;
+	};
+
+	/* YaCO AUX Uart */
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA		0x1b0b1
+			MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA		0x1b0b1
 		>;
 	};
 
@@ -805,19 +679,6 @@
 		>;
 	};
 
-	pinctrl_usdhc2: usdhc2grp {
-		fsl,pins = <
-			MX6QDL_PAD_SD2_CMD__SD2_CMD			0x170b9
-			MX6QDL_PAD_SD2_CLK__SD2_CLK			0x100b9
-			MX6QDL_PAD_SD2_DAT0__SD2_DATA0			0x170b9
-			MX6QDL_PAD_SD2_DAT1__SD2_DATA1			0x170b9
-			MX6QDL_PAD_SD2_DAT2__SD2_DATA2			0x170b9
-			MX6QDL_PAD_SD2_DAT3__SD2_DATA3			0x170b9
-			/* WL12xx IRQ */
-			MX6QDL_PAD_ENET_TXD0__GPIO1_IO30		0x10880
-		>;
-	};
-
 	pinctrl_usdhc3: usdhc3grp {
 		fsl,pins = <
 			MX6QDL_PAD_SD3_CMD__SD3_CMD			0x17099
@@ -833,10 +694,4 @@
 			MX6QDL_PAD_SD3_RST__SD3_RESET			0x1b0b1
 		>;
 	};
-
-	pinctrl_wifi_npd: wifinpdgrp {
-		fsl,pins = <
-			MX6QDL_PAD_ENET_RXD1__GPIO1_IO26		0x1b8b0
-		>;
-	};
 };
diff --git a/arch/arm/boot/dts/imx6qdl-wandboard.dtsi b/arch/arm/boot/dts/imx6qdl-wandboard.dtsi
index b62a0dbb033f..ec6fba5ee8fd 100644
--- a/arch/arm/boot/dts/imx6qdl-wandboard.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-wandboard.dtsi
@@ -309,6 +309,7 @@
 
 		ethphy: ethernet-phy@1 {
 			reg = <1>;
+			qca,clk-out-frequency = <125000000>;
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/imx6qdl.dtsi b/arch/arm/boot/dts/imx6qdl.dtsi
index f5de5def876d..ff1e0173b39b 100644
--- a/arch/arm/boot/dts/imx6qdl.dtsi
+++ b/arch/arm/boot/dts/imx6qdl.dtsi
@@ -55,19 +55,19 @@
 
 	clocks {
 		ckil {
-			compatible = "fsl,imx-ckil", "fixed-clock";
+			compatible = "fixed-clock";
 			#clock-cells = <0>;
 			clock-frequency = <32768>;
 		};
 
 		ckih1 {
-			compatible = "fsl,imx-ckih1", "fixed-clock";
+			compatible = "fixed-clock";
 			#clock-cells = <0>;
 			clock-frequency = <0>;
 		};
 
 		osc {
-			compatible = "fsl,imx-osc", "fixed-clock";
+			compatible = "fixed-clock";
 			#clock-cells = <0>;
 			clock-frequency = <24000000>;
 		};
@@ -143,7 +143,7 @@
 		#phy-cells = <0>;
 	};
 
-	soc {
+	soc: soc {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "simple-bus";
@@ -290,7 +290,7 @@
 			status = "disabled";
 		};
 
-		bus@2000000 { /* AIPS1 */
+		aips1: bus@2000000 { /* AIPS1 */
 			compatible = "fsl,aips-bus", "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -481,7 +481,7 @@
 					status = "okay";
 				};
 
-				spba@203c000 {
+				spba-bus@203c000 {
 					reg = <0x0203c000 0x4000>;
 				};
 			};
@@ -762,7 +762,7 @@
 					regulator-name = "vddpu";
 					regulator-min-microvolt = <725000>;
 					regulator-max-microvolt = <1450000>;
-					regulator-enable-ramp-delay = <150>;
+					regulator-enable-ramp-delay = <380>;
 					anatop-reg-offset = <0x140>;
 					anatop-vol-bit-shift = <9>;
 					anatop-vol-bit-width = <5>;
@@ -929,7 +929,7 @@
 				interrupts = <0 125 IRQ_TYPE_LEVEL_HIGH>;
 			};
 
-			sdma: sdma@20ec000 {
+			sdma: dma-controller@20ec000 {
 				compatible = "fsl,imx6q-sdma", "fsl,imx35-sdma";
 				reg = <0x020ec000 0x4000>;
 				interrupts = <0 2 IRQ_TYPE_LEVEL_HIGH>;
@@ -941,7 +941,7 @@
 			};
 		};
 
-		bus@2100000 { /* AIPS2 */
+		aips2: bus@2100000 { /* AIPS2 */
 			compatible = "fsl,aips-bus", "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
diff --git a/arch/arm/boot/dts/imx6qp-mba6b.dts b/arch/arm/boot/dts/imx6qp-mba6b.dts
new file mode 100644
index 000000000000..eee2e09d6e94
--- /dev/null
+++ b/arch/arm/boot/dts/imx6qp-mba6b.dts
@@ -0,0 +1,18 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright 2015-2021 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include "imx6qp-tqma6b.dtsi"
+#include "imx6qdl-mba6.dtsi"
+#include "imx6qdl-mba6b.dtsi"
+#include "imx6q-mba6.dtsi"
+
+/ {
+	model = "TQ TQMa6QP on MBa6x";
+	compatible = "tq,imx6qp-mba6x-b", "tq,mba6b",
+		     "tq,imx6qp-tqma6qp-b", "fsl,imx6qp";
+};
diff --git a/arch/arm/boot/dts/imx6qp-phytec-mira-rdk-nand.dts b/arch/arm/boot/dts/imx6qp-phytec-mira-rdk-nand.dts
index f27d7ab42626..a18266598d39 100644
--- a/arch/arm/boot/dts/imx6qp-phytec-mira-rdk-nand.dts
+++ b/arch/arm/boot/dts/imx6qp-phytec-mira-rdk-nand.dts
@@ -8,6 +8,9 @@
 #include "imx6qp.dtsi"
 #include "imx6qdl-phytec-phycore-som.dtsi"
 #include "imx6qdl-phytec-mira.dtsi"
+#include "imx6qdl-phytec-mira-peb-eval-01.dtsi"
+#include "imx6qdl-phytec-mira-peb-av-02.dtsi"
+#include "imx6qdl-phytec-mira-peb-wlbt-05.dtsi"
 
 / {
 	model = "PHYTEC phyBOARD-Mira QuadPlus Carrier-Board with NAND";
diff --git a/arch/arm/boot/dts/imx6qp-prtwd3.dts b/arch/arm/boot/dts/imx6qp-prtwd3.dts
index 7648e8a02000..cf6571cc4682 100644
--- a/arch/arm/boot/dts/imx6qp-prtwd3.dts
+++ b/arch/arm/boot/dts/imx6qp-prtwd3.dts
@@ -178,6 +178,8 @@
 				label = "cpu";
 				ethernet = <&fec>;
 				phy-mode = "rgmii-id";
+				rx-internal-delay-ps = <2000>;
+				tx-internal-delay-ps = <2000>;
 
 				fixed-link {
 					speed = <100>;
diff --git a/arch/arm/boot/dts/imx6qp-sabresd.dts b/arch/arm/boot/dts/imx6qp-sabresd.dts
index 480e73183f6b..f69eec18d865 100644
--- a/arch/arm/boot/dts/imx6qp-sabresd.dts
+++ b/arch/arm/boot/dts/imx6qp-sabresd.dts
@@ -50,8 +50,12 @@
 	};
 };
 
+&vgen3_reg {
+	regulator-always-on;
+};
+
 &pcie {
-	status = "disabled";
+	status = "okay";
 };
 
 &sata {
diff --git a/arch/arm/boot/dts/imx6qp-vicutp.dts b/arch/arm/boot/dts/imx6qp-vicutp.dts
index 7bad7ca6b12e..49ff145fffe5 100644
--- a/arch/arm/boot/dts/imx6qp-vicutp.dts
+++ b/arch/arm/boot/dts/imx6qp-vicutp.dts
@@ -6,6 +6,7 @@
 /dts-v1/;
 #include "imx6qp.dtsi"
 #include "imx6qdl-vicut1.dtsi"
+#include "imx6qdl-vicut1-12inch.dtsi"
 
 / {
 	model = "Kverneland UT1P Board";
diff --git a/arch/arm/boot/dts/imx6qp-yapp4-crux-plus.dts b/arch/arm/boot/dts/imx6qp-yapp4-crux-plus.dts
new file mode 100644
index 000000000000..afaf4a6759d4
--- /dev/null
+++ b/arch/arm/boot/dts/imx6qp-yapp4-crux-plus.dts
@@ -0,0 +1,58 @@
+// SPDX-License-Identifier: GPL-2.0
+//
+// Copyright (C) 2021 Y Soft Corporation, a.s.
+
+/dts-v1/;
+
+#include "imx6qp.dtsi"
+#include "imx6dl-yapp4-common.dtsi"
+
+/ {
+	model = "Y Soft IOTA Crux+ i.MX6QuadPlus board";
+	compatible = "ysoft,imx6qp-yapp4-crux-plus", "fsl,imx6qp";
+
+	memory@10000000 {
+		device_type = "memory";
+		reg = <0x10000000 0xf0000000>;
+	};
+};
+
+&gpio_oled {
+	status = "okay";
+};
+
+&leds {
+	status = "okay";
+};
+
+&oled_1305 {
+	status = "okay";
+};
+
+&oled_1309 {
+	status = "okay";
+};
+
+&reg_pu {
+	regulator-always-on;
+};
+
+&reg_usb_h1_vbus {
+	status = "okay";
+};
+
+&touchkeys {
+	status = "okay";
+};
+
+&uart2 {
+	status = "disabled";
+};
+
+&usbh1 {
+	status = "okay";
+};
+
+&usbphy2 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6qp.dtsi b/arch/arm/boot/dts/imx6qp.dtsi
index 050365513836..fc164991d2ae 100644
--- a/arch/arm/boot/dts/imx6qp.dtsi
+++ b/arch/arm/boot/dts/imx6qp.dtsi
@@ -9,12 +9,18 @@
 		ocram2: sram@940000 {
 			compatible = "mmio-sram";
 			reg = <0x00940000 0x20000>;
+			ranges = <0 0x00940000 0x20000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 			clocks = <&clks IMX6QDL_CLK_OCRAM>;
 		};
 
 		ocram3: sram@960000 {
 			compatible = "mmio-sram";
 			reg = <0x00960000 0x20000>;
+			ranges = <0 0x00960000 0x20000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 			clocks = <&clks IMX6QDL_CLK_OCRAM>;
 		};
 
diff --git a/arch/arm/boot/dts/imx6sl-evk.dts b/arch/arm/boot/dts/imx6sl-evk.dts
index 25f6f2fb1555..f16c830f1e91 100644
--- a/arch/arm/boot/dts/imx6sl-evk.dts
+++ b/arch/arm/boot/dts/imx6sl-evk.dts
@@ -137,7 +137,7 @@
 	pinctrl-0 = <&pinctrl_ecspi1>;
 	status = "okay";
 
-	flash: m25p80@0 {
+	flash: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "st,m25p32", "jedec,spi-nor";
diff --git a/arch/arm/boot/dts/imx6sl-tolino-shine2hd.dts b/arch/arm/boot/dts/imx6sl-tolino-shine2hd.dts
index a17b8bbbdb95..663ee9df79e6 100644
--- a/arch/arm/boot/dts/imx6sl-tolino-shine2hd.dts
+++ b/arch/arm/boot/dts/imx6sl-tolino-shine2hd.dts
@@ -27,7 +27,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gpio_keys>;
 
-		cover {
+		key-cover {
 			label = "Cover";
 			gpios = <&gpio5 12 GPIO_ACTIVE_LOW>;
 			linux,code = <SW_LID>;
@@ -35,19 +35,19 @@
 			wakeup-source;
 		};
 
-		fl {
+		key-fl {
 			label = "Frontlight";
 			gpios = <&gpio3 26 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_BRIGHTNESS_CYCLE>;
 		};
 
-		home {
+		key-home {
 			label = "Home";
 			gpios = <&gpio3 25 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_HOME>;
 		};
 
-		power {
+		key-power {
 			label = "Power";
 			gpios = <&gpio5 8 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
@@ -60,7 +60,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_led>;
 
-		on {
+		led-0 {
 			label = "tolinoshine2hd:white:on";
 			gpios = <&gpio5 13 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "timer";
diff --git a/arch/arm/boot/dts/imx6sl.dtsi b/arch/arm/boot/dts/imx6sl.dtsi
index c7d907c5c352..28111efb19a6 100644
--- a/arch/arm/boot/dts/imx6sl.dtsi
+++ b/arch/arm/boot/dts/imx6sl.dtsi
@@ -50,7 +50,7 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		cpu@0 {
+		cpu0: cpu@0 {
 			compatible = "arm,cortex-a9";
 			device_type = "cpu";
 			reg = <0x0>;
@@ -61,10 +61,10 @@
 				<792000  1175000>,
 				<396000  975000>;
 			fsl,soc-operating-points =
-				/* ARM kHz      SOC-PU uV */
-				<996000         1225000>,
-				<792000         1175000>,
-				<396000         1175000>;
+				/* ARM kHz	SOC-PU uV */
+				<996000		1225000>,
+				<792000		1175000>,
+				<396000		1175000>;
 			clock-latency = <61036>; /* two CLK32 periods */
 			#cooling-cells = <2>;
 			clocks = <&clks IMX6SL_CLK_ARM>, <&clks IMX6SL_CLK_PLL2_PFD2>,
@@ -115,6 +115,9 @@
 		ocram: sram@900000 {
 			compatible = "mmio-sram";
 			reg = <0x00900000 0x20000>;
+			ranges = <0 0x00900000 0x20000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 			clocks = <&clks IMX6SL_CLK_OCRAM>;
 		};
 
@@ -222,7 +225,7 @@
 
 				uart5: serial@2018000 {
 					compatible = "fsl,imx6sl-uart",
-						   "fsl,imx6q-uart", "fsl,imx21-uart";
+						     "fsl,imx6q-uart", "fsl,imx21-uart";
 					reg = <0x02018000 0x4000>;
 					interrupts = <0 30 IRQ_TYPE_LEVEL_HIGH>;
 					clocks = <&clks IMX6SL_CLK_UART>,
@@ -235,7 +238,7 @@
 
 				uart1: serial@2020000 {
 					compatible = "fsl,imx6sl-uart",
-						   "fsl,imx6q-uart", "fsl,imx21-uart";
+						     "fsl,imx6q-uart", "fsl,imx21-uart";
 					reg = <0x02020000 0x4000>;
 					interrupts = <0 26 IRQ_TYPE_LEVEL_HIGH>;
 					clocks = <&clks IMX6SL_CLK_UART>,
@@ -248,7 +251,7 @@
 
 				uart2: serial@2024000 {
 					compatible = "fsl,imx6sl-uart",
-						   "fsl,imx6q-uart", "fsl,imx21-uart";
+						     "fsl,imx6q-uart", "fsl,imx21-uart";
 					reg = <0x02024000 0x4000>;
 					interrupts = <0 27 IRQ_TYPE_LEVEL_HIGH>;
 					clocks = <&clks IMX6SL_CLK_UART>,
@@ -309,7 +312,7 @@
 
 				uart3: serial@2034000 {
 					compatible = "fsl,imx6sl-uart",
-						   "fsl,imx6q-uart", "fsl,imx21-uart";
+						     "fsl,imx6q-uart", "fsl,imx21-uart";
 					reg = <0x02034000 0x4000>;
 					interrupts = <0 28 IRQ_TYPE_LEVEL_HIGH>;
 					clocks = <&clks IMX6SL_CLK_UART>,
@@ -322,7 +325,7 @@
 
 				uart4: serial@2038000 {
 					compatible = "fsl,imx6sl-uart",
-						   "fsl,imx6q-uart", "fsl,imx21-uart";
+						     "fsl,imx6q-uart", "fsl,imx21-uart";
 					reg = <0x02038000 0x4000>;
 					interrupts = <0 29 IRQ_TYPE_LEVEL_HIGH>;
 					clocks = <&clks IMX6SL_CLK_UART>,
@@ -711,7 +714,7 @@
 						#power-domain-cells = <0>;
 						power-supply = <&reg_pu>;
 						clocks = <&clks IMX6SL_CLK_GPU2D_OVG>,
-						         <&clks IMX6SL_CLK_GPU2D_PODF>;
+							 <&clks IMX6SL_CLK_GPU2D_PODF>;
 					};
 
 					pd_disp: power-domain@2 {
@@ -747,7 +750,7 @@
 				interrupts = <0 6 IRQ_TYPE_LEVEL_HIGH>;
 			};
 
-			sdma: sdma@20ec000 {
+			sdma: dma-controller@20ec000 {
 				compatible = "fsl,imx6sl-sdma", "fsl,imx6q-sdma";
 				reg = <0x020ec000 0x4000>;
 				interrupts = <0 2 IRQ_TYPE_LEVEL_HIGH>;
diff --git a/arch/arm/boot/dts/imx6sll.dtsi b/arch/arm/boot/dts/imx6sll.dtsi
index d4a000c3dde7..2873369a57c0 100644
--- a/arch/arm/boot/dts/imx6sll.dtsi
+++ b/arch/arm/boot/dts/imx6sll.dtsi
@@ -115,6 +115,9 @@
 		ocram: sram@900000 {
 			compatible = "mmio-sram";
 			reg = <0x00900000 0x20000>;
+			ranges = <0 0x00900000 0x20000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 		};
 
 		intc: interrupt-controller@a01000 {
diff --git a/arch/arm/boot/dts/imx6sx-nitrogen6sx.dts b/arch/arm/boot/dts/imx6sx-nitrogen6sx.dts
index 66af78e83b70..a2c79bcf9a11 100644
--- a/arch/arm/boot/dts/imx6sx-nitrogen6sx.dts
+++ b/arch/arm/boot/dts/imx6sx-nitrogen6sx.dts
@@ -107,7 +107,7 @@
 	pinctrl-0 = <&pinctrl_ecspi1>;
 	status = "okay";
 
-	flash: m25p80@0 {
+	flash: flash@0 {
 		compatible = "microchip,sst25vf016b";
 		spi-max-frequency = <20000000>;
 		reg = <0>;
diff --git a/arch/arm/boot/dts/imx6sx-sdb-reva.dts b/arch/arm/boot/dts/imx6sx-sdb-reva.dts
index dce5dcf96c25..7dda42553f4b 100644
--- a/arch/arm/boot/dts/imx6sx-sdb-reva.dts
+++ b/arch/arm/boot/dts/imx6sx-sdb-reva.dts
@@ -123,7 +123,7 @@
 	pinctrl-0 = <&pinctrl_qspi2>;
 	status = "okay";
 
-	flash0: s25fl128s@0 {
+	flash0: flash@0 {
 		reg = <0>;
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -133,7 +133,7 @@
 		spi-tx-bus-width = <4>;
 	};
 
-	flash1: s25fl128s@2 {
+	flash1: flash@2 {
 		reg = <2>;
 		#address-cells = <1>;
 		#size-cells = <1>;
diff --git a/arch/arm/boot/dts/imx6sx-sdb.dts b/arch/arm/boot/dts/imx6sx-sdb.dts
index 99f4cf777a38..969cfe920d25 100644
--- a/arch/arm/boot/dts/imx6sx-sdb.dts
+++ b/arch/arm/boot/dts/imx6sx-sdb.dts
@@ -108,7 +108,7 @@
 	pinctrl-0 = <&pinctrl_qspi2>;
 	status = "okay";
 
-	flash0: n25q256a@0 {
+	flash0: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "micron,n25q256a", "jedec,spi-nor";
@@ -118,7 +118,7 @@
 		reg = <0>;
 	};
 
-	flash1: n25q256a@2 {
+	flash1: flash@2 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "micron,n25q256a", "jedec,spi-nor";
diff --git a/arch/arm/boot/dts/imx6sx-udoo-neo.dtsi b/arch/arm/boot/dts/imx6sx-udoo-neo.dtsi
index ee645655090d..c84ea1fac5e9 100644
--- a/arch/arm/boot/dts/imx6sx-udoo-neo.dtsi
+++ b/arch/arm/boot/dts/imx6sx-udoo-neo.dtsi
@@ -183,6 +183,27 @@
 	status = "okay";
 };
 
+&i2c3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	clock-frequency = <100000>;
+	status = "okay";
+
+	hdmi-transmitter@70 {
+		compatible = "nxp,tda998x";
+		reg = <0x70>;
+		interrupts-extended = <&gpio3 27 IRQ_TYPE_LEVEL_LOW>;
+
+		ports {
+			port {
+				hdmi: endpoint {
+					remote-endpoint = <&lcdc>;
+				};
+			};
+		};
+	};
+};
+
 &i2c4 { /* Onboard Motion sensors */
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_i2c4>;
@@ -190,10 +211,22 @@
 	status = "disabled";
 };
 
+&lcdif1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_lcd>;
+	status = "okay";
+
+	port {
+		lcdc: endpoint {
+			remote-endpoint = <&hdmi>;
+		};
+	};
+};
+
 &iomuxc {
 	pinctrl_bt_reg: btreggrp {
 		fsl,pins =
-			<MX6SX_PAD_KEY_ROW2__GPIO2_IO_17        0x15059>;
+			<MX6SX_PAD_KEY_ROW2__GPIO2_IO_17	0x15059>;
 	};
 
 	pinctrl_enet1: enet1grp {
@@ -227,12 +260,52 @@
 			<MX6SX_PAD_GPIO1_IO02__I2C2_SCL		0x4001b8b1>;
 	};
 
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins =
+			<MX6SX_PAD_KEY_ROW4__I2C3_SDA			0x4001b8b1>,
+			<MX6SX_PAD_KEY_COL4__I2C3_SCL			0x4001b8b1>;
+	};
+
 	pinctrl_i2c4: i2c4grp {
 		fsl,pins =
 			<MX6SX_PAD_USB_H_DATA__I2C4_SDA		0x4001b8b1>,
 			<MX6SX_PAD_USB_H_STROBE__I2C4_SCL	0x4001b8b1>;
 	};
 
+	pinctrl_lcd: lcdgrp {
+		fsl,pins = <
+			MX6SX_PAD_LCD1_DATA00__LCDIF1_DATA_0		0x4001b0b0
+			MX6SX_PAD_LCD1_DATA01__LCDIF1_DATA_1		0x4001b0b0
+			MX6SX_PAD_LCD1_DATA02__LCDIF1_DATA_2		0x4001b0b0
+			MX6SX_PAD_LCD1_DATA03__LCDIF1_DATA_3		0x4001b0b0
+			MX6SX_PAD_LCD1_DATA04__LCDIF1_DATA_4		0x4001b0b0
+			MX6SX_PAD_LCD1_DATA05__LCDIF1_DATA_5		0x4001b0b0
+			MX6SX_PAD_LCD1_DATA06__LCDIF1_DATA_6		0x4001b0b0
+			MX6SX_PAD_LCD1_DATA07__LCDIF1_DATA_7		0x4001b0b0
+			MX6SX_PAD_LCD1_DATA08__LCDIF1_DATA_8		0x4001b0b0
+			MX6SX_PAD_LCD1_DATA09__LCDIF1_DATA_9		0x4001b0b0
+			MX6SX_PAD_LCD1_DATA10__LCDIF1_DATA_10		0x4001b0b0
+			MX6SX_PAD_LCD1_DATA11__LCDIF1_DATA_11		0x4001b0b0
+			MX6SX_PAD_LCD1_DATA12__LCDIF1_DATA_12		0x4001b0b0
+			MX6SX_PAD_LCD1_DATA13__LCDIF1_DATA_13		0x4001b0b0
+			MX6SX_PAD_LCD1_DATA14__LCDIF1_DATA_14		0x4001b0b0
+			MX6SX_PAD_LCD1_DATA15__LCDIF1_DATA_15		0x4001b0b0
+			MX6SX_PAD_LCD1_DATA16__LCDIF1_DATA_16		0x4001b0b0
+			MX6SX_PAD_LCD1_DATA17__LCDIF1_DATA_17		0x4001b0b0
+			MX6SX_PAD_LCD1_DATA18__LCDIF1_DATA_18		0x4001b0b0
+			MX6SX_PAD_LCD1_DATA19__LCDIF1_DATA_19		0x4001b0b0
+			MX6SX_PAD_LCD1_DATA20__LCDIF1_DATA_20		0x4001b0b0
+			MX6SX_PAD_LCD1_DATA21__LCDIF1_DATA_21		0x4001b0b0
+			MX6SX_PAD_LCD1_DATA22__LCDIF1_DATA_22		0x4001b0b0
+			MX6SX_PAD_LCD1_DATA23__LCDIF1_DATA_23		0x4001b0b0
+			MX6SX_PAD_LCD1_CLK__LCDIF1_CLK		0x4001b0b0
+			MX6SX_PAD_LCD1_ENABLE__LCDIF1_ENABLE		0x4001b0b0
+			MX6SX_PAD_LCD1_VSYNC__LCDIF1_VSYNC		0x4001b0b0
+			MX6SX_PAD_LCD1_HSYNC__LCDIF1_HSYNC		0x4001b0b0
+			MX6SX_PAD_LCD1_RESET__GPIO3_IO_27		0x4001b0b0
+		>;
+	};
+
 	pinctrl_uart1: uart1grp {
 		fsl,pins =
 			<MX6SX_PAD_GPIO1_IO04__UART1_DCE_TX	0x1b0b1>,
@@ -273,24 +346,23 @@
 
 	pinctrl_otg1_reg: otg1grp {
 		fsl,pins =
-			<MX6SX_PAD_GPIO1_IO09__GPIO1_IO_9        0x10b0>;
+			<MX6SX_PAD_GPIO1_IO09__GPIO1_IO_9	0x10b0>;
 	};
 
-
 	pinctrl_otg2_reg: otg2grp {
 		fsl,pins =
-			<MX6SX_PAD_NAND_RE_B__GPIO4_IO_12        0x10b0>;
+			<MX6SX_PAD_NAND_RE_B__GPIO4_IO_12	0x10b0>;
 	};
 
 	pinctrl_usb_otg1: usbotg1grp {
 		fsl,pins =
-			<MX6SX_PAD_GPIO1_IO10__ANATOP_OTG1_ID    0x17059>,
-			<MX6SX_PAD_GPIO1_IO08__USB_OTG1_OC       0x10b0>;
+			<MX6SX_PAD_GPIO1_IO10__ANATOP_OTG1_ID	0x17059>,
+			<MX6SX_PAD_GPIO1_IO08__USB_OTG1_OC	0x10b0>;
 	};
 
 	pinctrl_usb_otg2: usbot2ggrp {
 		fsl,pins =
-			<MX6SX_PAD_QSPI1A_DATA0__USB_OTG2_OC     0x10b0>;
+			<MX6SX_PAD_QSPI1A_DATA0__USB_OTG2_OC	0x10b0>;
 	};
 
 	pinctrl_usdhc2: usdhc2grp {
diff --git a/arch/arm/boot/dts/imx6sx.dtsi b/arch/arm/boot/dts/imx6sx.dtsi
index fc6334336b3d..abc3572d699e 100644
--- a/arch/arm/boot/dts/imx6sx.dtsi
+++ b/arch/arm/boot/dts/imx6sx.dtsi
@@ -154,7 +154,7 @@
 		#phy-cells = <0>;
 	};
 
-	soc {
+	soc: soc {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "simple-bus";
@@ -164,12 +164,18 @@
 		ocram_s: sram@8f8000 {
 			compatible = "mmio-sram";
 			reg = <0x008f8000 0x4000>;
+			ranges = <0 0x008f8000 0x4000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 			clocks = <&clks IMX6SX_CLK_OCRAM_S>;
 		};
 
 		ocram: sram@900000 {
 			compatible = "mmio-sram";
 			reg = <0x00900000 0x20000>;
+			ranges = <0 0x00900000 0x20000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 			clocks = <&clks IMX6SX_CLK_OCRAM>;
 		};
 
@@ -842,7 +848,7 @@
 				reg = <0x020e4000 0x4000>;
 			};
 
-			sdma: sdma@20ec000 {
+			sdma: dma-controller@20ec000 {
 				compatible = "fsl,imx6sx-sdma", "fsl,imx6q-sdma";
 				reg = <0x020ec000 0x4000>;
 				interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
diff --git a/arch/arm/boot/dts/imx6ul-14x14-evk.dtsi b/arch/arm/boot/dts/imx6ul-14x14-evk.dtsi
index a3fde3316c73..c83e64a62d8a 100644
--- a/arch/arm/boot/dts/imx6ul-14x14-evk.dtsi
+++ b/arch/arm/boot/dts/imx6ul-14x14-evk.dtsi
@@ -82,7 +82,7 @@
 			"AMIC", "MICB";
 	};
 
-	spi4 {
+	spi-4 {
 		compatible = "spi-gpio";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_spi4>;
@@ -286,7 +286,7 @@
 	pinctrl-0 = <&pinctrl_qspi>;
 	status = "okay";
 
-	flash0: n25q256a@0 {
+	flash0: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "micron,n25q256a", "jedec,spi-nor";
diff --git a/arch/arm/boot/dts/imx6ul-imx6ull-opos6uldev.dtsi b/arch/arm/boot/dts/imx6ul-imx6ull-opos6uldev.dtsi
index 935a77d717a6..18cac19aa9b0 100644
--- a/arch/arm/boot/dts/imx6ul-imx6ull-opos6uldev.dtsi
+++ b/arch/arm/boot/dts/imx6ul-imx6ull-opos6uldev.dtsi
@@ -114,18 +114,6 @@
 	pinctrl-0 = <&pinctrl_ecspi4>;
 	cs-gpios = <&gpio4 9 GPIO_ACTIVE_LOW>, <&gpio4 3 GPIO_ACTIVE_LOW>;
 	status = "okay";
-
-	spidev0: spi@0 {
-		compatible = "spidev";
-		reg = <0>;
-		spi-max-frequency = <5000000>;
-	};
-
-	spidev1: spi@1 {
-		compatible = "spidev";
-		reg = <1>;
-		spi-max-frequency = <5000000>;
-	};
 };
 
 &i2c1 {
diff --git a/arch/arm/boot/dts/imx6ul-kontron-bl-43.dts b/arch/arm/boot/dts/imx6ul-kontron-bl-43.dts
new file mode 100644
index 000000000000..0c643706a158
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ul-kontron-bl-43.dts
@@ -0,0 +1,103 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2017 exceet electronics GmbH
+ * Copyright (C) 2018 Kontron Electronics GmbH
+ * Copyright (c) 2019 Krzysztof Kozlowski <krzk@kernel.org>
+ */
+
+#include "imx6ul-kontron-bl.dts"
+
+/ {
+	model = "Kontron BL i.MX6UL 43 (N631X S 43)";
+	compatible = "kontron,bl-imx6ul-43", "kontron,bl-imx6ul",
+		     "kontron,sl-imx6ul", "fsl,imx6ul";
+
+	backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm7 0 5000000>;
+		brightness-levels = <0 4 8 16 32 64 128 255>;
+		default-brightness-level = <6>;
+		status = "okay";
+	};
+};
+
+&i2c4 {
+	touchscreen@5d {
+		compatible = "goodix,gt928";
+		reg = <0x5d>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_cap_touch>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <6 IRQ_TYPE_LEVEL_LOW>;
+		reset-gpios = <&gpio5 8 GPIO_ACTIVE_HIGH>;
+		irq-gpios = <&gpio5 6 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&lcdif {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_lcdif_dat &pinctrl_lcdif_ctrl>;
+	/* Leave status disabled because of missing display panel node */
+};
+
+&pwm7 {
+	#pwm-cells = <2>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm7>;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_cap_touch: captouchgrp {
+		fsl,pins = <
+			MX6UL_PAD_SNVS_TAMPER6__GPIO5_IO06	0x1b0b0 /* Touch Interrupt */
+			MX6UL_PAD_SNVS_TAMPER7__GPIO5_IO07	0x1b0b0 /* Touch Reset */
+			MX6UL_PAD_SNVS_TAMPER8__GPIO5_IO08	0x1b0b0 /* Touch Wake */
+		>;
+	};
+
+	pinctrl_lcdif_ctrl: lcdifctrlgrp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_CLK__LCDIF_CLK		0x79
+			MX6UL_PAD_LCD_ENABLE__LCDIF_ENABLE	0x79
+			MX6UL_PAD_LCD_HSYNC__LCDIF_HSYNC	0x79
+			MX6UL_PAD_LCD_VSYNC__LCDIF_VSYNC	0x79
+			MX6UL_PAD_LCD_RESET__LCDIF_RESET	0x79
+		>;
+	};
+
+	pinctrl_lcdif_dat: lcdifdatgrp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA00__LCDIF_DATA00	0x79
+			MX6UL_PAD_LCD_DATA01__LCDIF_DATA01	0x79
+			MX6UL_PAD_LCD_DATA02__LCDIF_DATA02	0x79
+			MX6UL_PAD_LCD_DATA03__LCDIF_DATA03	0x79
+			MX6UL_PAD_LCD_DATA04__LCDIF_DATA04	0x79
+			MX6UL_PAD_LCD_DATA05__LCDIF_DATA05	0x79
+			MX6UL_PAD_LCD_DATA06__LCDIF_DATA06	0x79
+			MX6UL_PAD_LCD_DATA07__LCDIF_DATA07	0x79
+			MX6UL_PAD_LCD_DATA08__LCDIF_DATA08	0x79
+			MX6UL_PAD_LCD_DATA09__LCDIF_DATA09	0x79
+			MX6UL_PAD_LCD_DATA10__LCDIF_DATA10	0x79
+			MX6UL_PAD_LCD_DATA11__LCDIF_DATA11	0x79
+			MX6UL_PAD_LCD_DATA12__LCDIF_DATA12	0x79
+			MX6UL_PAD_LCD_DATA13__LCDIF_DATA13	0x79
+			MX6UL_PAD_LCD_DATA14__LCDIF_DATA14	0x79
+			MX6UL_PAD_LCD_DATA15__LCDIF_DATA15	0x79
+			MX6UL_PAD_LCD_DATA16__LCDIF_DATA16	0x79
+			MX6UL_PAD_LCD_DATA17__LCDIF_DATA17	0x79
+			MX6UL_PAD_LCD_DATA18__LCDIF_DATA18	0x79
+			MX6UL_PAD_LCD_DATA19__LCDIF_DATA19	0x79
+			MX6UL_PAD_LCD_DATA20__LCDIF_DATA20	0x79
+			MX6UL_PAD_LCD_DATA21__LCDIF_DATA21	0x79
+			MX6UL_PAD_LCD_DATA22__LCDIF_DATA22	0x79
+			MX6UL_PAD_LCD_DATA23__LCDIF_DATA23	0x79
+		>;
+	};
+
+	pinctrl_pwm7: pwm7grp {
+		fsl,pins = <
+			MX6UL_PAD_CSI_VSYNC__PWM7_OUT		0x110b0
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6ul-kontron-bl-common.dtsi b/arch/arm/boot/dts/imx6ul-kontron-bl-common.dtsi
new file mode 100644
index 000000000000..43868311f48a
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ul-kontron-bl-common.dtsi
@@ -0,0 +1,405 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2017 exceet electronics GmbH
+ * Copyright (C) 2018 Kontron Electronics GmbH
+ * Copyright (c) 2019 Krzysztof Kozlowski <krzk@kernel.org>
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	gpio-leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_leds>;
+
+		led1 {
+			label = "debug-led1";
+			gpios = <&gpio1 30 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+			linux,default-trigger = "heartbeat";
+		};
+
+		led2 {
+			label = "debug-led2";
+			gpios = <&gpio5 3 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led3 {
+			label = "debug-led3";
+			gpios = <&gpio5 2 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+	};
+
+	pwm-beeper {
+		compatible = "pwm-beeper";
+		pwms = <&pwm8 0 5000>;
+	};
+
+	reg_3v3: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	reg_5v: regulator-5v {
+		compatible = "regulator-fixed";
+		regulator-name = "5v";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	reg_usb_otg1_vbus: regulator-usb-otg1-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_otg1_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio1 4 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	reg_vref_adc: regulator-vref-adc {
+		compatible = "regulator-fixed";
+		regulator-name = "vref-adc";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+};
+
+&adc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc1>;
+	vref-supply = <&reg_vref_adc>;
+	status = "okay";
+};
+
+&can2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan2>;
+	status = "okay";
+};
+
+&ecspi1 {
+	cs-gpios = <&gpio4 26 GPIO_ACTIVE_LOW>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1>;
+	status = "okay";
+
+	eeprom@0 {
+		compatible = "anvo,anv32e61w", "atmel,at25";
+		reg = <0>;
+		spi-max-frequency = <20000000>;
+		spi-cpha;
+		spi-cpol;
+		pagesize = <1>;
+		size = <8192>;
+		address-width = <16>;
+	};
+};
+
+&fec1 {
+	pinctrl-0 = <&pinctrl_enet1>;
+	/delete-node/ mdio;
+};
+
+&fec2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet2 &pinctrl_enet2_mdio>;
+	phy-mode = "rmii";
+	phy-handle = <&ethphy2>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy1: ethernet-phy@1 {
+			reg = <1>;
+			micrel,led-mode = <0>;
+			clocks = <&clks IMX6UL_CLK_ENET_REF>;
+			clock-names = "rmii-ref";
+		};
+
+		ethphy2: ethernet-phy@2 {
+			reg = <2>;
+			micrel,led-mode = <0>;
+			clocks = <&clks IMX6UL_CLK_ENET2_REF>;
+			clock-names = "rmii-ref";
+		};
+	};
+};
+
+&i2c1 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+};
+
+&i2c4 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c4>;
+	status = "okay";
+
+	rtc@32 {
+		compatible = "epson,rx8900";
+		reg = <0x32>;
+	};
+};
+
+&pwm8 {
+	#pwm-cells = <2>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm8>;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	linux,rs485-enabled-at-boot-time;
+	rs485-rx-during-tx;
+	rs485-rts-active-low;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+	status = "okay";
+};
+
+&usbotg1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg1>;
+	dr_mode = "otg";
+	srp-disable;
+	hnp-disable;
+	adp-disable;
+	over-current-active-low;
+	vbus-supply = <&reg_usb_otg1_vbus>;
+	status = "okay";
+};
+
+&usbotg2 {
+	dr_mode = "host";
+	disable-over-current;
+	vbus-supply = <&reg_5v>;
+	status = "okay";
+};
+
+&usdhc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	cd-gpios = <&gpio1 19 GPIO_ACTIVE_LOW>;
+	keep-power-in-suspend;
+	wakeup-source;
+	vmmc-supply = <&reg_3v3>;
+	voltage-ranges = <3300 3300>;
+	no-1-8-v;
+	status = "okay";
+};
+
+&usdhc2 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
+	non-removable;
+	keep-power-in-suspend;
+	wakeup-source;
+	vmmc-supply = <&reg_3v3>;
+	voltage-ranges = <3300 3300>;
+	no-1-8-v;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl-0 = <&pinctrl_reset_out &pinctrl_gpio>;
+
+	pinctrl_adc1: adc1grp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO02__GPIO1_IO02	0xb0
+			MX6UL_PAD_GPIO1_IO03__GPIO1_IO03	0xb0
+			MX6UL_PAD_GPIO1_IO08__GPIO1_IO08	0xb0
+		>;
+	};
+
+	pinctrl_ecspi1: ecspi1grp {
+		fsl,pins = <
+			MX6UL_PAD_CSI_DATA07__ECSPI1_MISO	0x100b1
+			MX6UL_PAD_CSI_DATA06__ECSPI1_MOSI	0x100b1
+			MX6UL_PAD_CSI_DATA04__ECSPI1_SCLK	0x100b1
+			MX6UL_PAD_CSI_DATA05__GPIO4_IO26	0x100b1	/* ECSPI1-CS1 */
+		>;
+	};
+
+	pinctrl_enet2: enet2grp {
+		fsl,pins = <
+			MX6UL_PAD_ENET2_RX_EN__ENET2_RX_EN	0x1b0b0
+			MX6UL_PAD_ENET2_RX_ER__ENET2_RX_ER	0x1b0b0
+			MX6UL_PAD_ENET2_RX_DATA0__ENET2_RDATA00	0x1b0b0
+			MX6UL_PAD_ENET2_RX_DATA1__ENET2_RDATA01	0x1b0b0
+			MX6UL_PAD_ENET2_TX_EN__ENET2_TX_EN	0x1b0b0
+			MX6UL_PAD_ENET2_TX_DATA0__ENET2_TDATA00	0x1b0b0
+			MX6UL_PAD_ENET2_TX_DATA1__ENET2_TDATA01	0x1b0b0
+			MX6UL_PAD_ENET2_TX_CLK__ENET2_REF_CLK2	0x4001b009
+		>;
+	};
+
+	pinctrl_enet2_mdio: enet2mdiogrp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO07__ENET2_MDC		0x1b0b0
+			MX6UL_PAD_GPIO1_IO06__ENET2_MDIO	0x1b0b0
+		>;
+	};
+
+	pinctrl_flexcan2: flexcan2grp{
+		fsl,pins = <
+			MX6UL_PAD_UART2_RTS_B__FLEXCAN2_RX	0x1b020
+			MX6UL_PAD_UART2_CTS_B__FLEXCAN2_TX	0x1b020
+		>;
+	};
+
+	pinctrl_gpio: gpiogrp {
+		fsl,pins = <
+			MX6UL_PAD_SNVS_TAMPER5__GPIO5_IO05	0x1b0b0	/* DOUT1 */
+			MX6UL_PAD_SNVS_TAMPER4__GPIO5_IO04	0x1b0b0	/* DIN1 */
+			MX6UL_PAD_SNVS_TAMPER1__GPIO5_IO01	0x1b0b0	/* DOUT2 */
+			MX6UL_PAD_SNVS_TAMPER0__GPIO5_IO00	0x1b0b0	/* DIN2 */
+		>;
+	};
+
+	pinctrl_gpio_leds: gpioledsgrp {
+		fsl,pins = <
+			MX6UL_PAD_UART5_TX_DATA__GPIO1_IO30	0x1b0b0	/* LED H14 */
+			MX6UL_PAD_SNVS_TAMPER3__GPIO5_IO03	0x1b0b0	/* LED H15 */
+			MX6UL_PAD_SNVS_TAMPER2__GPIO5_IO02	0x1b0b0	/* LED H16 */
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX6UL_PAD_CSI_PIXCLK__I2C1_SCL		0x4001b8b0
+			MX6UL_PAD_CSI_MCLK__I2C1_SDA		0x4001b8b0
+		>;
+	};
+
+	pinctrl_i2c4: i2c4grp {
+		fsl,pins = <
+			MX6UL_PAD_UART2_TX_DATA__I2C4_SCL	0x4001f8b0
+			MX6UL_PAD_UART2_RX_DATA__I2C4_SDA	0x4001f8b0
+		>;
+	};
+
+	pinctrl_pwm8: pwm8grp {
+		fsl,pins = <
+			MX6UL_PAD_CSI_HSYNC__PWM8_OUT		0x110b0
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX	0x1b0b1
+			MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_DATA04__UART2_DCE_TX	0x1b0b1
+			MX6UL_PAD_NAND_DATA05__UART2_DCE_RX	0x1b0b1
+			MX6UL_PAD_NAND_DATA06__UART2_DCE_CTS	0x1b0b1
+			/*
+			 * mux unused RTS to make sure it doesn't cause
+			 * any interrupts when it is undefined
+			 */
+			MX6UL_PAD_NAND_DATA07__UART2_DCE_RTS	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <
+			MX6UL_PAD_UART3_TX_DATA__UART3_DCE_TX	0x1b0b1
+			MX6UL_PAD_UART3_RX_DATA__UART3_DCE_RX	0x1b0b1
+			MX6UL_PAD_UART3_CTS_B__UART3_DCE_CTS	0x1b0b1
+			MX6UL_PAD_UART3_RTS_B__UART3_DCE_RTS	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart4: uart4grp {
+		fsl,pins = <
+			MX6UL_PAD_UART4_TX_DATA__UART4_DCE_TX	0x1b0b1
+			MX6UL_PAD_UART4_RX_DATA__UART4_DCE_RX	0x1b0b1
+		>;
+	};
+
+	pinctrl_usbotg1: usbotg1 {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO04__GPIO1_IO04	0x1b0b0
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x17059
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x10059
+			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x17059
+			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x17059
+			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x17059
+			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x17059
+			MX6UL_PAD_UART1_RTS_B__GPIO1_IO19	0x100b1	/* SD1_CD */
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK		0x10059
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD		0x17059
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0	0x17059
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1	0x17059
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2	0x17059
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3	0x17059
+		>;
+	};
+
+	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK		0x100b9
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD		0x170b9
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0	0x170b9
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1	0x170b9
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2	0x170b9
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3	0x170b9
+		>;
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK		0x100f9
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD		0x170f9
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0	0x170f9
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1	0x170f9
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2	0x170f9
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3	0x170f9
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6ul-kontron-bl.dts b/arch/arm/boot/dts/imx6ul-kontron-bl.dts
new file mode 100644
index 000000000000..dadf6d3d5f52
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ul-kontron-bl.dts
@@ -0,0 +1,16 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2017 exceet electronics GmbH
+ * Copyright (C) 2018 Kontron Electronics GmbH
+ * Copyright (c) 2019 Krzysztof Kozlowski <krzk@kernel.org>
+ */
+
+/dts-v1/;
+
+#include "imx6ul-kontron-sl.dtsi"
+#include "imx6ul-kontron-bl-common.dtsi"
+
+/ {
+	model = "Kontron BL i.MX6UL (N631X S)";
+	compatible = "kontron,bl-imx6ul", "kontron,sl-imx6ul", "fsl,imx6ul";
+};
diff --git a/arch/arm/boot/dts/imx6ul-kontron-n6310-s-43.dts b/arch/arm/boot/dts/imx6ul-kontron-n6310-s-43.dts
deleted file mode 100644
index 5bfad4655b22..000000000000
--- a/arch/arm/boot/dts/imx6ul-kontron-n6310-s-43.dts
+++ /dev/null
@@ -1,103 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Copyright (C) 2017 exceet electronics GmbH
- * Copyright (C) 2018 Kontron Electronics GmbH
- * Copyright (c) 2019 Krzysztof Kozlowski <krzk@kernel.org>
- */
-
-#include "imx6ul-kontron-n6310-s.dts"
-
-/ {
-	model = "Kontron N6310 S 43";
-	compatible = "kontron,imx6ul-n6310-s-43", "kontron,imx6ul-n6310-s",
-		     "kontron,imx6ul-n6310-som", "fsl,imx6ul";
-
-	backlight {
-		compatible = "pwm-backlight";
-		pwms = <&pwm7 0 5000000>;
-		brightness-levels = <0 4 8 16 32 64 128 255>;
-		default-brightness-level = <6>;
-		status = "okay";
-	};
-};
-
-&i2c4 {
-	touchscreen@5d {
-		compatible = "goodix,gt928";
-		reg = <0x5d>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_cap_touch>;
-		interrupt-parent = <&gpio5>;
-		interrupts = <6 IRQ_TYPE_LEVEL_LOW>;
-		reset-gpios = <&gpio5 8 GPIO_ACTIVE_HIGH>;
-		irq-gpios = <&gpio5 6 GPIO_ACTIVE_HIGH>;
-	};
-};
-
-&lcdif {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_lcdif_dat &pinctrl_lcdif_ctrl>;
-	/* Leave status disabled because of missing display panel node */
-};
-
-&pwm7 {
-	#pwm-cells = <2>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_pwm7>;
-	status = "okay";
-};
-
-&iomuxc {
-	pinctrl_cap_touch: captouchgrp {
-		fsl,pins = <
-			MX6UL_PAD_SNVS_TAMPER6__GPIO5_IO06	0x1b0b0 /* Touch Interrupt */
-			MX6UL_PAD_SNVS_TAMPER7__GPIO5_IO07	0x1b0b0 /* Touch Reset */
-			MX6UL_PAD_SNVS_TAMPER8__GPIO5_IO08	0x1b0b0 /* Touch Wake */
-		>;
-	};
-
-	pinctrl_lcdif_ctrl: lcdifctrlgrp {
-		fsl,pins = <
-			MX6UL_PAD_LCD_CLK__LCDIF_CLK		0x79
-			MX6UL_PAD_LCD_ENABLE__LCDIF_ENABLE	0x79
-			MX6UL_PAD_LCD_HSYNC__LCDIF_HSYNC	0x79
-			MX6UL_PAD_LCD_VSYNC__LCDIF_VSYNC	0x79
-			MX6UL_PAD_LCD_RESET__LCDIF_RESET	0x79
-		>;
-	};
-
-	pinctrl_lcdif_dat: lcdifdatgrp {
-		fsl,pins = <
-			MX6UL_PAD_LCD_DATA00__LCDIF_DATA00	0x79
-			MX6UL_PAD_LCD_DATA01__LCDIF_DATA01	0x79
-			MX6UL_PAD_LCD_DATA02__LCDIF_DATA02	0x79
-			MX6UL_PAD_LCD_DATA03__LCDIF_DATA03	0x79
-			MX6UL_PAD_LCD_DATA04__LCDIF_DATA04	0x79
-			MX6UL_PAD_LCD_DATA05__LCDIF_DATA05	0x79
-			MX6UL_PAD_LCD_DATA06__LCDIF_DATA06	0x79
-			MX6UL_PAD_LCD_DATA07__LCDIF_DATA07	0x79
-			MX6UL_PAD_LCD_DATA08__LCDIF_DATA08	0x79
-			MX6UL_PAD_LCD_DATA09__LCDIF_DATA09	0x79
-			MX6UL_PAD_LCD_DATA10__LCDIF_DATA10	0x79
-			MX6UL_PAD_LCD_DATA11__LCDIF_DATA11	0x79
-			MX6UL_PAD_LCD_DATA12__LCDIF_DATA12	0x79
-			MX6UL_PAD_LCD_DATA13__LCDIF_DATA13	0x79
-			MX6UL_PAD_LCD_DATA14__LCDIF_DATA14	0x79
-			MX6UL_PAD_LCD_DATA15__LCDIF_DATA15	0x79
-			MX6UL_PAD_LCD_DATA16__LCDIF_DATA16	0x79
-			MX6UL_PAD_LCD_DATA17__LCDIF_DATA17	0x79
-			MX6UL_PAD_LCD_DATA18__LCDIF_DATA18	0x79
-			MX6UL_PAD_LCD_DATA19__LCDIF_DATA19	0x79
-			MX6UL_PAD_LCD_DATA20__LCDIF_DATA20	0x79
-			MX6UL_PAD_LCD_DATA21__LCDIF_DATA21	0x79
-			MX6UL_PAD_LCD_DATA22__LCDIF_DATA22	0x79
-			MX6UL_PAD_LCD_DATA23__LCDIF_DATA23	0x79
-		>;
-	};
-
-	pinctrl_pwm7: pwm7grp {
-		fsl,pins = <
-			MX6UL_PAD_CSI_VSYNC__PWM7_OUT		0x110b0
-		>;
-	};
-};
diff --git a/arch/arm/boot/dts/imx6ul-kontron-n6310-s.dts b/arch/arm/boot/dts/imx6ul-kontron-n6310-s.dts
deleted file mode 100644
index 5a3e06d6219b..000000000000
--- a/arch/arm/boot/dts/imx6ul-kontron-n6310-s.dts
+++ /dev/null
@@ -1,17 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Copyright (C) 2017 exceet electronics GmbH
- * Copyright (C) 2018 Kontron Electronics GmbH
- * Copyright (c) 2019 Krzysztof Kozlowski <krzk@kernel.org>
- */
-
-/dts-v1/;
-
-#include "imx6ul-kontron-n6310-som.dtsi"
-#include "imx6ul-kontron-n6x1x-s.dtsi"
-
-/ {
-	model = "Kontron N6310 S";
-	compatible = "kontron,imx6ul-n6310-s", "kontron,imx6ul-n6310-som",
-		     "fsl,imx6ul";
-};
diff --git a/arch/arm/boot/dts/imx6ul-kontron-n6310-som.dtsi b/arch/arm/boot/dts/imx6ul-kontron-n6310-som.dtsi
deleted file mode 100644
index 47d3ce5d255f..000000000000
--- a/arch/arm/boot/dts/imx6ul-kontron-n6310-som.dtsi
+++ /dev/null
@@ -1,41 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Copyright (C) 2017 exceet electronics GmbH
- * Copyright (C) 2018 Kontron Electronics GmbH
- * Copyright (c) 2019 Krzysztof Kozlowski <krzk@kernel.org>
- */
-
-#include "imx6ul.dtsi"
-#include "imx6ul-kontron-n6x1x-som-common.dtsi"
-
-/ {
-	model = "Kontron N6310 SOM";
-	compatible = "kontron,imx6ul-n6310-som", "fsl,imx6ul";
-
-	memory@80000000 {
-		reg = <0x80000000 0x10000000>;
-		device_type = "memory";
-	};
-};
-
-&qspi {
-	spi-flash@0 {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		compatible = "spi-nand";
-		spi-max-frequency = <108000000>;
-		spi-tx-bus-width = <4>;
-		spi-rx-bus-width = <4>;
-		reg = <0>;
-
-		partition@0 {
-			label = "ubi1";
-			reg = <0x00000000 0x08000000>;
-		};
-
-		partition@8000000 {
-			label = "ubi2";
-			reg = <0x08000000 0x08000000>;
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/imx6ul-kontron-n6311-s.dts b/arch/arm/boot/dts/imx6ul-kontron-n6311-s.dts
deleted file mode 100644
index 239a1af3aeaa..000000000000
--- a/arch/arm/boot/dts/imx6ul-kontron-n6311-s.dts
+++ /dev/null
@@ -1,16 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Copyright (C) 2017 exceet electronics GmbH
- * Copyright (C) 2018 Kontron Electronics GmbH
- */
-
-/dts-v1/;
-
-#include "imx6ul-kontron-n6311-som.dtsi"
-#include "imx6ul-kontron-n6x1x-s.dtsi"
-
-/ {
-	model = "Kontron N6311 S";
-	compatible = "kontron,imx6ul-n6311-s", "kontron,imx6ul-n6311-som",
-		     "fsl,imx6ul";
-};
diff --git a/arch/arm/boot/dts/imx6ul-kontron-n6311-som.dtsi b/arch/arm/boot/dts/imx6ul-kontron-n6311-som.dtsi
deleted file mode 100644
index a095a7654ac6..000000000000
--- a/arch/arm/boot/dts/imx6ul-kontron-n6311-som.dtsi
+++ /dev/null
@@ -1,40 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Copyright (C) 2017 exceet electronics GmbH
- * Copyright (C) 2018 Kontron Electronics GmbH
- */
-
-#include "imx6ul.dtsi"
-#include "imx6ul-kontron-n6x1x-som-common.dtsi"
-
-/ {
-	model = "Kontron N6311 SOM";
-	compatible = "kontron,imx6ul-n6311-som", "fsl,imx6ul";
-
-	memory@80000000 {
-		reg = <0x80000000 0x20000000>;
-		device_type = "memory";
-	};
-};
-
-&qspi {
-	spi-flash@0 {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		compatible = "spi-nand";
-		spi-max-frequency = <104000000>;
-		spi-tx-bus-width = <4>;
-		spi-rx-bus-width = <4>;
-		reg = <0>;
-
-		partition@0 {
-			label = "ubi1";
-			reg = <0x00000000 0x08000000>;
-		};
-
-		partition@8000000 {
-			label = "ubi2";
-			reg = <0x08000000 0x18000000>;
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/imx6ul-kontron-n6x1x-s.dtsi b/arch/arm/boot/dts/imx6ul-kontron-n6x1x-s.dtsi
deleted file mode 100644
index 770f59b23102..000000000000
--- a/arch/arm/boot/dts/imx6ul-kontron-n6x1x-s.dtsi
+++ /dev/null
@@ -1,406 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Copyright (C) 2017 exceet electronics GmbH
- * Copyright (C) 2018 Kontron Electronics GmbH
- * Copyright (c) 2019 Krzysztof Kozlowski <krzk@kernel.org>
- */
-
-#include <dt-bindings/gpio/gpio.h>
-
-/ {
-	gpio-leds {
-		compatible = "gpio-leds";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_gpio_leds>;
-
-		led1 {
-			label = "debug-led1";
-			gpios = <&gpio1 30 GPIO_ACTIVE_LOW>;
-			default-state = "off";
-			linux,default-trigger = "heartbeat";
-		};
-
-		led2 {
-			label = "debug-led2";
-			gpios = <&gpio5 3 GPIO_ACTIVE_LOW>;
-			default-state = "off";
-		};
-
-		led3 {
-			label = "debug-led3";
-			gpios = <&gpio5 2 GPIO_ACTIVE_LOW>;
-			default-state = "off";
-		};
-	};
-
-	pwm-beeper {
-		compatible = "pwm-beeper";
-		pwms = <&pwm8 0 5000>;
-	};
-
-	reg_3v3: regulator-3v3 {
-		compatible = "regulator-fixed";
-		regulator-name = "3v3";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-	};
-
-	reg_5v: regulator-5v {
-		compatible = "regulator-fixed";
-		regulator-name = "5v";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-	};
-
-	reg_usb_otg1_vbus: regulator-usb-otg1-vbus {
-		compatible = "regulator-fixed";
-		regulator-name = "usb_otg1_vbus";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-		gpio = <&gpio1 4 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-	};
-
-	reg_vref_adc: regulator-vref-adc {
-		compatible = "regulator-fixed";
-		regulator-name = "vref-adc";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-	};
-};
-
-&adc1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_adc1>;
-	num-channels = <3>;
-	vref-supply = <&reg_vref_adc>;
-	status = "okay";
-};
-
-&can2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_flexcan2>;
-	status = "okay";
-};
-
-&ecspi1 {
-	cs-gpios = <&gpio4 26 GPIO_ACTIVE_LOW>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_ecspi1>;
-	status = "okay";
-
-	eeprom@0 {
-		compatible = "anvo,anv32e61w", "atmel,at25";
-		reg = <0>;
-		spi-max-frequency = <20000000>;
-		spi-cpha;
-		spi-cpol;
-		pagesize = <1>;
-		size = <8192>;
-		address-width = <16>;
-	};
-};
-
-&fec1 {
-	pinctrl-0 = <&pinctrl_enet1>;
-	/delete-node/ mdio;
-};
-
-&fec2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_enet2 &pinctrl_enet2_mdio>;
-	phy-mode = "rmii";
-	phy-handle = <&ethphy2>;
-	status = "okay";
-
-	mdio {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		ethphy1: ethernet-phy@1 {
-			reg = <1>;
-			micrel,led-mode = <0>;
-			clocks = <&clks IMX6UL_CLK_ENET_REF>;
-			clock-names = "rmii-ref";
-		};
-
-		ethphy2: ethernet-phy@2 {
-			reg = <2>;
-			micrel,led-mode = <0>;
-			clocks = <&clks IMX6UL_CLK_ENET2_REF>;
-			clock-names = "rmii-ref";
-		};
-	};
-};
-
-&i2c1 {
-	clock-frequency = <100000>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_i2c1>;
-	status = "okay";
-};
-
-&i2c4 {
-	clock-frequency = <100000>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_i2c4>;
-	status = "okay";
-
-	rtc@32 {
-		compatible = "epson,rx8900";
-		reg = <0x32>;
-	};
-};
-
-&pwm8 {
-	#pwm-cells = <2>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_pwm8>;
-	status = "okay";
-};
-
-&uart1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart1>;
-	status = "okay";
-};
-
-&uart2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart2>;
-	linux,rs485-enabled-at-boot-time;
-	rs485-rx-during-tx;
-	rs485-rts-active-low;
-	uart-has-rtscts;
-	status = "okay";
-};
-
-&uart3 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart3>;
-	fsl,uart-has-rtscts;
-	status = "okay";
-};
-
-&uart4 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart4>;
-	status = "okay";
-};
-
-&usbotg1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usbotg1>;
-	dr_mode = "otg";
-	srp-disable;
-	hnp-disable;
-	adp-disable;
-	over-current-active-low;
-	vbus-supply = <&reg_usb_otg1_vbus>;
-	status = "okay";
-};
-
-&usbotg2 {
-	dr_mode = "host";
-	disable-over-current;
-	vbus-supply = <&reg_5v>;
-	status = "okay";
-};
-
-&usdhc1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc1>;
-	cd-gpios = <&gpio1 19 GPIO_ACTIVE_LOW>;
-	keep-power-in-suspend;
-	wakeup-source;
-	vmmc-supply = <&reg_3v3>;
-	voltage-ranges = <3300 3300>;
-	no-1-8-v;
-	status = "okay";
-};
-
-&usdhc2 {
-	pinctrl-names = "default", "state_100mhz", "state_200mhz";
-	pinctrl-0 = <&pinctrl_usdhc2>;
-	pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
-	pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
-	non-removable;
-	keep-power-in-suspend;
-	wakeup-source;
-	vmmc-supply = <&reg_3v3>;
-	voltage-ranges = <3300 3300>;
-	no-1-8-v;
-	status = "okay";
-};
-
-&iomuxc {
-	pinctrl-0 = <&pinctrl_reset_out &pinctrl_gpio>;
-
-	pinctrl_adc1: adc1grp {
-		fsl,pins = <
-			MX6UL_PAD_GPIO1_IO02__GPIO1_IO02	0xb0
-			MX6UL_PAD_GPIO1_IO03__GPIO1_IO03	0xb0
-			MX6UL_PAD_GPIO1_IO08__GPIO1_IO08	0xb0
-		>;
-	};
-
-	pinctrl_ecspi1: ecspi1grp {
-		fsl,pins = <
-			MX6UL_PAD_CSI_DATA07__ECSPI1_MISO	0x100b1
-			MX6UL_PAD_CSI_DATA06__ECSPI1_MOSI	0x100b1
-			MX6UL_PAD_CSI_DATA04__ECSPI1_SCLK	0x100b1
-			MX6UL_PAD_CSI_DATA05__GPIO4_IO26	0x100b1	/* ECSPI1-CS1 */
-		>;
-	};
-
-	pinctrl_enet2: enet2grp {
-		fsl,pins = <
-			MX6UL_PAD_ENET2_RX_EN__ENET2_RX_EN	0x1b0b0
-			MX6UL_PAD_ENET2_RX_ER__ENET2_RX_ER	0x1b0b0
-			MX6UL_PAD_ENET2_RX_DATA0__ENET2_RDATA00	0x1b0b0
-			MX6UL_PAD_ENET2_RX_DATA1__ENET2_RDATA01	0x1b0b0
-			MX6UL_PAD_ENET2_TX_EN__ENET2_TX_EN	0x1b0b0
-			MX6UL_PAD_ENET2_TX_DATA0__ENET2_TDATA00	0x1b0b0
-			MX6UL_PAD_ENET2_TX_DATA1__ENET2_TDATA01	0x1b0b0
-			MX6UL_PAD_ENET2_TX_CLK__ENET2_REF_CLK2	0x4001b009
-		>;
-	};
-
-	pinctrl_enet2_mdio: enet2mdiogrp {
-		fsl,pins = <
-			MX6UL_PAD_GPIO1_IO07__ENET2_MDC		0x1b0b0
-			MX6UL_PAD_GPIO1_IO06__ENET2_MDIO	0x1b0b0
-		>;
-	};
-
-	pinctrl_flexcan2: flexcan2grp{
-		fsl,pins = <
-			MX6UL_PAD_UART2_RTS_B__FLEXCAN2_RX	0x1b020
-			MX6UL_PAD_UART2_CTS_B__FLEXCAN2_TX	0x1b020
-		>;
-	};
-
-	pinctrl_gpio: gpiogrp {
-		fsl,pins = <
-			MX6UL_PAD_SNVS_TAMPER5__GPIO5_IO05	0x1b0b0	/* DOUT1 */
-			MX6UL_PAD_SNVS_TAMPER4__GPIO5_IO04	0x1b0b0	/* DIN1 */
-			MX6UL_PAD_SNVS_TAMPER1__GPIO5_IO01	0x1b0b0	/* DOUT2 */
-			MX6UL_PAD_SNVS_TAMPER0__GPIO5_IO00	0x1b0b0	/* DIN2 */
-		>;
-	};
-
-	pinctrl_gpio_leds: gpioledsgrp {
-		fsl,pins = <
-			MX6UL_PAD_UART5_TX_DATA__GPIO1_IO30	0x1b0b0	/* LED H14 */
-			MX6UL_PAD_SNVS_TAMPER3__GPIO5_IO03	0x1b0b0	/* LED H15 */
-			MX6UL_PAD_SNVS_TAMPER2__GPIO5_IO02	0x1b0b0	/* LED H16 */
-		>;
-	};
-
-	pinctrl_i2c1: i2c1grp {
-		fsl,pins = <
-			MX6UL_PAD_CSI_PIXCLK__I2C1_SCL		0x4001b8b0
-			MX6UL_PAD_CSI_MCLK__I2C1_SDA		0x4001b8b0
-		>;
-	};
-
-	pinctrl_i2c4: i2c4grp {
-		fsl,pins = <
-			MX6UL_PAD_UART2_TX_DATA__I2C4_SCL	0x4001f8b0
-			MX6UL_PAD_UART2_RX_DATA__I2C4_SDA	0x4001f8b0
-		>;
-	};
-
-	pinctrl_pwm8: pwm8grp {
-		fsl,pins = <
-			MX6UL_PAD_CSI_HSYNC__PWM8_OUT		0x110b0
-		>;
-	};
-
-	pinctrl_uart1: uart1grp {
-		fsl,pins = <
-			MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX	0x1b0b1
-			MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX	0x1b0b1
-		>;
-	};
-
-	pinctrl_uart2: uart2grp {
-		fsl,pins = <
-			MX6UL_PAD_NAND_DATA04__UART2_DCE_TX	0x1b0b1
-			MX6UL_PAD_NAND_DATA05__UART2_DCE_RX	0x1b0b1
-			MX6UL_PAD_NAND_DATA06__UART2_DCE_CTS	0x1b0b1
-			/*
-			 * mux unused RTS to make sure it doesn't cause
-			 * any interrupts when it is undefined
-			 */
-			MX6UL_PAD_NAND_DATA07__UART2_DCE_RTS	0x1b0b1
-		>;
-	};
-
-	pinctrl_uart3: uart3grp {
-		fsl,pins = <
-			MX6UL_PAD_UART3_TX_DATA__UART3_DCE_TX	0x1b0b1
-			MX6UL_PAD_UART3_RX_DATA__UART3_DCE_RX	0x1b0b1
-			MX6UL_PAD_UART3_CTS_B__UART3_DCE_CTS	0x1b0b1
-			MX6UL_PAD_UART3_RTS_B__UART3_DCE_RTS	0x1b0b1
-		>;
-	};
-
-	pinctrl_uart4: uart4grp {
-		fsl,pins = <
-			MX6UL_PAD_UART4_TX_DATA__UART4_DCE_TX	0x1b0b1
-			MX6UL_PAD_UART4_RX_DATA__UART4_DCE_RX	0x1b0b1
-		>;
-	};
-
-	pinctrl_usbotg1: usbotg1 {
-		fsl,pins = <
-			MX6UL_PAD_GPIO1_IO04__GPIO1_IO04	0x1b0b0
-		>;
-	};
-
-	pinctrl_usdhc1: usdhc1grp {
-		fsl,pins = <
-			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x17059
-			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x10059
-			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x17059
-			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x17059
-			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x17059
-			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x17059
-			MX6UL_PAD_UART1_RTS_B__GPIO1_IO19	0x100b1	/* SD1_CD */
-		>;
-	};
-
-	pinctrl_usdhc2: usdhc2grp {
-		fsl,pins = <
-			MX6UL_PAD_NAND_RE_B__USDHC2_CLK		0x10059
-			MX6UL_PAD_NAND_WE_B__USDHC2_CMD		0x17059
-			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0	0x17059
-			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1	0x17059
-			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2	0x17059
-			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3	0x17059
-		>;
-	};
-
-	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
-		fsl,pins = <
-			MX6UL_PAD_NAND_RE_B__USDHC2_CLK		0x100b9
-			MX6UL_PAD_NAND_WE_B__USDHC2_CMD		0x170b9
-			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0	0x170b9
-			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1	0x170b9
-			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2	0x170b9
-			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3	0x170b9
-		>;
-	};
-
-	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
-		fsl,pins = <
-			MX6UL_PAD_NAND_RE_B__USDHC2_CLK		0x100f9
-			MX6UL_PAD_NAND_WE_B__USDHC2_CMD		0x170f9
-			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0	0x170f9
-			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1	0x170f9
-			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2	0x170f9
-			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3	0x170f9
-		>;
-	};
-};
diff --git a/arch/arm/boot/dts/imx6ul-kontron-n6x1x-som-common.dtsi b/arch/arm/boot/dts/imx6ul-kontron-n6x1x-som-common.dtsi
deleted file mode 100644
index 2a449a3c1ae2..000000000000
--- a/arch/arm/boot/dts/imx6ul-kontron-n6x1x-som-common.dtsi
+++ /dev/null
@@ -1,122 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Copyright (C) 2017 exceet electronics GmbH
- * Copyright (C) 2018 Kontron Electronics GmbH
- * Copyright (c) 2019 Krzysztof Kozlowski <krzk@kernel.org>
- */
-
-#include <dt-bindings/gpio/gpio.h>
-
-/ {
-	chosen {
-		stdout-path = &uart4;
-	};
-};
-
-&ecspi2 {
-	cs-gpios = <&gpio4 22 GPIO_ACTIVE_LOW>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_ecspi2>;
-	status = "okay";
-
-	spi-flash@0 {
-		compatible = "mxicy,mx25v8035f", "jedec,spi-nor";
-		spi-max-frequency = <50000000>;
-		reg = <0>;
-	};
-};
-
-&fec1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_enet1 &pinctrl_enet1_mdio>;
-	phy-mode = "rmii";
-	phy-handle = <&ethphy1>;
-	status = "okay";
-
-	mdio {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		ethphy1: ethernet-phy@1 {
-			reg = <1>;
-			micrel,led-mode = <0>;
-			clocks = <&clks IMX6UL_CLK_ENET_REF>;
-			clock-names = "rmii-ref";
-		};
-	};
-};
-
-&fec2 {
-	phy-mode = "rmii";
-	status = "disabled";
-};
-
-&qspi {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_qspi>;
-	status = "okay";
-};
-
-&wdog1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_wdog>;
-	fsl,ext-reset-output;
-	status = "okay";
-};
-
-&iomuxc {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_reset_out>;
-
-	pinctrl_ecspi2: ecspi2grp {
-		fsl,pins = <
-			MX6UL_PAD_CSI_DATA03__ECSPI2_MISO      0x100b1
-			MX6UL_PAD_CSI_DATA02__ECSPI2_MOSI      0x100b1
-			MX6UL_PAD_CSI_DATA00__ECSPI2_SCLK      0x100b1
-			MX6UL_PAD_CSI_DATA01__GPIO4_IO22       0x100b1
-		>;
-	};
-
-	pinctrl_enet1: enet1grp {
-		fsl,pins = <
-			MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN      0x1b0b0
-			MX6UL_PAD_ENET1_RX_ER__ENET1_RX_ER      0x1b0b0
-			MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00 0x1b0b0
-			MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01 0x1b0b0
-			MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN      0x1b0b0
-			MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00 0x1b0b0
-			MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01 0x1b0b0
-			MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1  0x4001b009
-		>;
-	};
-
-	pinctrl_enet1_mdio: enet1mdiogrp {
-		fsl,pins = <
-			MX6UL_PAD_GPIO1_IO07__ENET1_MDC         0x1b0b0
-			MX6UL_PAD_GPIO1_IO06__ENET1_MDIO        0x1b0b0
-		>;
-	};
-
-	pinctrl_qspi: qspigrp {
-		fsl,pins = <
-			MX6UL_PAD_NAND_WP_B__QSPI_A_SCLK        0x70a1
-			MX6UL_PAD_NAND_READY_B__QSPI_A_DATA00   0x70a1
-			MX6UL_PAD_NAND_CE0_B__QSPI_A_DATA01     0x70a1
-			MX6UL_PAD_NAND_CE1_B__QSPI_A_DATA02     0x70a1
-			MX6UL_PAD_NAND_CLE__QSPI_A_DATA03       0x70a1
-			MX6UL_PAD_NAND_DQS__QSPI_A_SS0_B        0x70a1
-		>;
-	};
-
-	pinctrl_reset_out: rstoutgrp {
-		fsl,pins = <
-			MX6UL_PAD_SNVS_TAMPER9__GPIO5_IO09      0x1b0b0
-		>;
-	};
-
-	pinctrl_wdog: wdoggrp {
-		fsl,pins = <
-			MX6UL_PAD_GPIO1_IO09__WDOG1_WDOG_ANY    0x18b0
-		>;
-	};
-};
diff --git a/arch/arm/boot/dts/imx6ul-kontron-sl-common.dtsi b/arch/arm/boot/dts/imx6ul-kontron-sl-common.dtsi
new file mode 100644
index 000000000000..dcf88f610346
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ul-kontron-sl-common.dtsi
@@ -0,0 +1,137 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2017 exceet electronics GmbH
+ * Copyright (C) 2018 Kontron Electronics GmbH
+ * Copyright (c) 2019 Krzysztof Kozlowski <krzk@kernel.org>
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	chosen {
+		stdout-path = &uart4;
+	};
+
+	memory@80000000 {
+		reg = <0x80000000 0x10000000>;
+		device_type = "memory";
+	};
+};
+
+&ecspi2 {
+	cs-gpios = <&gpio4 22 GPIO_ACTIVE_LOW>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi2>;
+	status = "okay";
+
+	flash@0 {
+		compatible = "mxicy,mx25v8035f", "jedec,spi-nor";
+		spi-max-frequency = <50000000>;
+		reg = <0>;
+	};
+};
+
+&fec1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet1 &pinctrl_enet1_mdio>;
+	phy-mode = "rmii";
+	phy-handle = <&ethphy1>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy1: ethernet-phy@1 {
+			reg = <1>;
+			micrel,led-mode = <0>;
+			clocks = <&clks IMX6UL_CLK_ENET_REF>;
+			clock-names = "rmii-ref";
+		};
+	};
+};
+
+&fec2 {
+	phy-mode = "rmii";
+	status = "disabled";
+};
+
+&qspi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_qspi>;
+	status = "okay";
+
+	spi-flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "spi-nand";
+		spi-max-frequency = <104000000>;
+		spi-tx-bus-width = <4>;
+		spi-rx-bus-width = <4>;
+		reg = <0>;
+	};
+};
+
+&wdog1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog>;
+	fsl,ext-reset-output;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_reset_out>;
+
+	pinctrl_ecspi2: ecspi2grp {
+		fsl,pins = <
+			MX6UL_PAD_CSI_DATA03__ECSPI2_MISO      0x100b1
+			MX6UL_PAD_CSI_DATA02__ECSPI2_MOSI      0x100b1
+			MX6UL_PAD_CSI_DATA00__ECSPI2_SCLK      0x100b1
+			MX6UL_PAD_CSI_DATA01__GPIO4_IO22       0x100b1
+		>;
+	};
+
+	pinctrl_enet1: enet1grp {
+		fsl,pins = <
+			MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN      0x1b0b0
+			MX6UL_PAD_ENET1_RX_ER__ENET1_RX_ER      0x1b0b0
+			MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00 0x1b0b0
+			MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01 0x1b0b0
+			MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN      0x1b0b0
+			MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00 0x1b0b0
+			MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01 0x1b0b0
+			MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1  0x4001b009
+		>;
+	};
+
+	pinctrl_enet1_mdio: enet1mdiogrp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO07__ENET1_MDC         0x1b0b0
+			MX6UL_PAD_GPIO1_IO06__ENET1_MDIO        0x1b0b0
+		>;
+	};
+
+	pinctrl_qspi: qspigrp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_WP_B__QSPI_A_SCLK        0x70a1
+			MX6UL_PAD_NAND_READY_B__QSPI_A_DATA00   0x70a1
+			MX6UL_PAD_NAND_CE0_B__QSPI_A_DATA01     0x70a1
+			MX6UL_PAD_NAND_CE1_B__QSPI_A_DATA02     0x70a1
+			MX6UL_PAD_NAND_CLE__QSPI_A_DATA03       0x70a1
+			MX6UL_PAD_NAND_DQS__QSPI_A_SS0_B        0x70a1
+		>;
+	};
+
+	pinctrl_reset_out: rstoutgrp {
+		fsl,pins = <
+			MX6UL_PAD_SNVS_TAMPER9__GPIO5_IO09      0x1b0b0
+		>;
+	};
+
+	pinctrl_wdog: wdoggrp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO09__WDOG1_WDOG_ANY    0x18b0
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6ul-kontron-sl.dtsi b/arch/arm/boot/dts/imx6ul-kontron-sl.dtsi
new file mode 100644
index 000000000000..0580d043e5ae
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ul-kontron-sl.dtsi
@@ -0,0 +1,14 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2017 exceet electronics GmbH
+ * Copyright (C) 2018 Kontron Electronics GmbH
+ * Copyright (c) 2019 Krzysztof Kozlowski <krzk@kernel.org>
+ */
+
+#include "imx6ul.dtsi"
+#include "imx6ul-kontron-sl-common.dtsi"
+
+/ {
+	model = "Kontron SL i.MX6UL (N631X SOM)";
+	compatible = "kontron,sl-imx6ul", "fsl,imx6ul";
+};
diff --git a/arch/arm/boot/dts/imx6ul-phytec-segin-ff-rdk-nand.dts b/arch/arm/boot/dts/imx6ul-phytec-segin-ff-rdk-nand.dts
index bff98e676980..607eddc5030f 100644
--- a/arch/arm/boot/dts/imx6ul-phytec-segin-ff-rdk-nand.dts
+++ b/arch/arm/boot/dts/imx6ul-phytec-segin-ff-rdk-nand.dts
@@ -10,6 +10,7 @@
 #include "imx6ul-phytec-segin.dtsi"
 #include "imx6ul-phytec-segin-peb-eval-01.dtsi"
 #include "imx6ul-phytec-segin-peb-av-02.dtsi"
+#include "imx6ul-phytec-segin-peb-wlbt-05.dtsi"
 
 / {
 	model = "PHYTEC phyBOARD-Segin i.MX6 UltraLite Full Featured with NAND";
diff --git a/arch/arm/boot/dts/imx6ul-phytec-segin-peb-av-02.dtsi b/arch/arm/boot/dts/imx6ul-phytec-segin-peb-av-02.dtsi
index 7cda6944501d..ec042648bd98 100644
--- a/arch/arm/boot/dts/imx6ul-phytec-segin-peb-av-02.dtsi
+++ b/arch/arm/boot/dts/imx6ul-phytec-segin-peb-av-02.dtsi
@@ -11,7 +11,7 @@
 		brightness-levels = <0 4 8 16 32 64 128 255>;
 		default-brightness-level = <5>;
 		power-supply = <&reg_backlight_en>;
-		pwms = <&pwm3 0 5000000>;
+		pwms = <&pwm3 0 5000000 0>;
 		status = "disabled";
 	};
 
@@ -72,8 +72,8 @@
 			st,settling = <2>;
 			st,fraction-z = <7>;
 			st,i-drive = <1>;
-			touchscreen-inverted-x = <1>;
-			touchscreen-inverted-y = <1>;
+			touchscreen-inverted-x;
+			touchscreen-inverted-y;
 		};
 	};
 };
@@ -91,7 +91,6 @@
 };
 
 &pwm3 {
-	#pwm-cells = <2>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm3>;
 	status = "disabled";
diff --git a/arch/arm/boot/dts/imx6ul-phytec-segin-peb-wlbt-05.dtsi b/arch/arm/boot/dts/imx6ul-phytec-segin-peb-wlbt-05.dtsi
new file mode 100644
index 000000000000..04477fd4b9a9
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ul-phytec-segin-peb-wlbt-05.dtsi
@@ -0,0 +1,90 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2021 PHYTEC Messtechnik GmbH
+ * Author: Yunus Bas <y.bas@phytec.de>
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	reg_wl_en: regulator-wl-en {
+		compatible = "regulator-fixed";
+		regulator-name = "wlan_en";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_wl>;
+		gpio = <&gpio5 9 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		startup-delay-us = <100>;
+		status = "disabled";
+	};
+};
+
+&iomuxc {
+	pinctrl_bt: btgrp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO01__GPIO1_IO01	0x3031	/* BT ENABLE */
+			MX6UL_PAD_GPIO1_IO03__GPIO1_IO03	0x3031	/* HOST WAKEUP */
+			MX6UL_PAD_JTAG_MOD__GPIO1_IO10		0x3031	/* DEV WAKEUP */
+		>;
+	};
+
+	pinctrl_uart2_bt: uart2grp-bt {
+		fsl,pins = <
+			MX6UL_PAD_UART2_TX_DATA__UART2_DCE_TX   0x17059
+			MX6UL_PAD_UART2_RX_DATA__UART2_DCE_RX   0x17059
+			MX6UL_PAD_UART2_CTS_B__UART2_DCE_CTS    0x17059
+			MX6UL_PAD_UART2_RTS_B__UART2_DCE_RTS    0x17059
+		>;
+	};
+
+	pinctrl_usdhc2_wl: usdhc2grp-wl {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA18__USDHC2_CMD    0x10051
+			MX6UL_PAD_LCD_DATA19__USDHC2_CLK    0x10061
+			MX6UL_PAD_LCD_DATA20__USDHC2_DATA0  0x10051
+			MX6UL_PAD_LCD_DATA21__USDHC2_DATA1  0x10051
+			MX6UL_PAD_LCD_DATA22__USDHC2_DATA2  0x10051
+			MX6UL_PAD_LCD_DATA23__USDHC2_DATA3  0x10051
+		>;
+	};
+
+	pinctrl_wl: wlgrp {
+		fsl,pins = <
+			MX6UL_PAD_SNVS_TAMPER9__GPIO5_IO09  0x3031	/* WLAN ENABLE */
+		>;
+	};
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2_bt &pinctrl_bt>;
+	uart-has-rtscts;
+	status = "disabled";
+
+	bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		shutdown-gpios = <&gpio1 1 GPIO_ACTIVE_HIGH>;
+		device-wakeup-gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>;
+		host-wakeup-gpios = <&gpio1 3 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&usdhc2 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc2_wl>;
+	vmmc-supply = <&reg_wl_en>;
+	bus-width = <4>;
+	non-removable;
+	no-1-8-v;
+	status = "disabled";
+
+	brmcf: wifi@1 {
+		compatible = "brcm,bcm4329-fmac";
+		reg = <1>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6ul-phytec-segin.dtsi b/arch/arm/boot/dts/imx6ul-phytec-segin.dtsi
index 0d4ba9494cf2..38ea4dcfa228 100644
--- a/arch/arm/boot/dts/imx6ul-phytec-segin.dtsi
+++ b/arch/arm/boot/dts/imx6ul-phytec-segin.dtsi
@@ -83,11 +83,6 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_adc1>;
 	vref-supply = <&reg_adc1_vref_3v3>;
-	/*
-	 * driver can not separate a specific channel so we request 4 channels
-	 * here - we need only the fourth channel
-	 */
-	num-channels = <4>;
 	status = "disabled";
 };
 
diff --git a/arch/arm/boot/dts/imx6ul-prti6g.dts b/arch/arm/boot/dts/imx6ul-prti6g.dts
index d62015701d0a..c18390f238e1 100644
--- a/arch/arm/boot/dts/imx6ul-prti6g.dts
+++ b/arch/arm/boot/dts/imx6ul-prti6g.dts
@@ -78,12 +78,6 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_ecspi2>;
 	status = "okay";
-
-	spi@0 {
-		compatible = "spidev";
-		reg = <0>;
-		spi-max-frequency = <1000000>;
-	};
 };
 
 &fec1 {
diff --git a/arch/arm/boot/dts/imx6ul-tqma6ul-common.dtsi b/arch/arm/boot/dts/imx6ul-tqma6ul-common.dtsi
new file mode 100644
index 000000000000..eca94ed6451b
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ul-tqma6ul-common.dtsi
@@ -0,0 +1,211 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2018-2022 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+/*
+ * Common for
+ * - TQMa6ULx
+ * - TQMa6ULxL
+ * - TQMa6ULLx
+ * - TQMa6ULLxL
+ */
+
+/ {
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x10000000>;
+	};
+};
+
+&i2c4 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c4>;
+	pinctrl-1 = <&pinctrl_i2c4_recovery>;
+	scl-gpios = <&gpio1 20 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio1 21 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "okay";
+
+	pfuze3000: pmic@8 {
+		compatible = "fsl,pfuze3000";
+		reg = <0x08>;
+
+		regulators {
+			reg_sw1a: sw1a {
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-ramp-delay = <6250>;
+				/* not used */
+			};
+
+			reg_sw1b_core: sw1b {
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <1475000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <6250>;
+			};
+
+			reg_sw2: sw2 {
+				regulator-min-microvolt = <2500000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			reg_sw3_ddr: sw3 {
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <1650000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			reg_swbst: swbst {
+				regulator-min-microvolt = <5000000>;
+				regulator-max-microvolt = <5150000>;
+				/* not used */
+			};
+
+			reg_snvs_3v0: vsnvs {
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			reg_vrefddr: vrefddr {
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			reg_vccsd: vccsd {
+				regulator-min-microvolt = <2850000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			reg_v33_3v3: v33 {
+				regulator-min-microvolt = <2850000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+
+			reg_vldo1_3v3: vldo1 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				/* not used */
+			};
+
+			reg_vldo2: vldo2 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1550000>;
+				/* not used */
+			};
+
+			reg_vldo3: vldo3 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				/* not used */
+			};
+
+			reg_vldo4: vldo4 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+			};
+		};
+	};
+
+	jc42_1a: eeprom-temperature-sensor@1a {
+		compatible = "nxp,se97", "jedec,jc-42.4-temp";
+		reg = <0x1a>;
+	};
+
+	m24c64_50: eeprom@50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+		pagesize = <32>;
+	};
+
+	m24c02_52: eeprom@52 {
+		compatible = "nxp,se97b", "atmel,24c02";
+		reg = <0x52>;
+		pagesize = <16>;
+		read-only;
+	};
+
+	rtc0: rtc@68 {
+		compatible = "dallas,ds1339";
+		reg = <0x68>;
+	};
+};
+
+&gpio4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pmic>;
+
+	/*
+	 * PMIC & temperature sensor IRQ
+	 * Both do currently not use IRQ
+	 * potentially dangerous if used on baseboard
+	 */
+	pmic-int-hog {
+		gpio-hog;
+		gpios = <24 0>;
+		input;
+	};
+};
+
+&qspi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_qspi>;
+	status = "okay";
+
+	flash0: flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "jedec,spi-nor";
+		spi-max-frequency = <33000000>;
+		spi-rx-bus-width = <4>;
+		spi-tx-bus-width = <1>;
+		reg = <0>;
+	};
+};
+
+/* eMMC */
+&usdhc2 {
+	pinctrl-names = "default", "state_100mhz" , "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
+
+	bus-width = <8>;
+	disable-wp;
+	non-removable;
+	no-sdio;
+	no-sd;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_i2c4: i2c4grp {
+		fsl,pins = <
+			MX6UL_PAD_UART2_TX_DATA__I2C4_SCL	0x4001b8b0
+			MX6UL_PAD_UART2_RX_DATA__I2C4_SDA	0x4001b8b0
+		>;
+	};
+
+	pinctrl_i2c4_recovery: i2c4recoverygrp {
+		fsl,pins = <
+			MX6UL_PAD_UART2_TX_DATA__GPIO1_IO20	0x4001b8b0
+			MX6UL_PAD_UART2_RX_DATA__GPIO1_IO21	0x4001b8b0
+		>;
+	};
+
+	pinctrl_pmic: pmic {
+		fsl,pins = <
+			/* PMIC irq */
+			MX6UL_PAD_CSI_DATA03__GPIO4_IO24	0x1b099
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6ul-tqma6ul1-mba6ulx.dts b/arch/arm/boot/dts/imx6ul-tqma6ul1-mba6ulx.dts
new file mode 100644
index 000000000000..f2a5f17f312e
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ul-tqma6ul1-mba6ulx.dts
@@ -0,0 +1,55 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2018-2022 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+/dts-v1/;
+
+#include "imx6ul-tqma6ul1.dtsi"
+#include "mba6ulx.dtsi"
+
+/ {
+	model = "TQ-Systems TQMa6UL1 SoM on MBa6ULx board";
+	compatible = "tq,imx6ul-tqma6ul1-mba6ulx", "tq,imx6ul-tqma6ul1", "fsl,imx6ul";
+};
+
+/*
+ * Note: can2 and fec2 are enabled on mba6ulx level (for i.MX6ULG2 usage)
+ * and need to be disabled here again
+ */
+&can2 {
+	status = "disabled";
+};
+
+&fec1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet1>, <&pinctrl_enet1_mdc>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy0: ethernet-phy@0 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			max-speed = <100>;
+			reg = <0>;
+		};
+	};
+};
+
+&fec2 {
+	/delete-property/ phy-handle;
+	/delete-node/ mdio;
+};
+
+&iomuxc {
+	pinctrl_enet1_mdc: enet1mdcgrp {
+		fsl,pins = <
+			/* mdio */
+			MX6UL_PAD_GPIO1_IO07__ENET1_MDC		0x1b0b0
+			MX6UL_PAD_GPIO1_IO06__ENET1_MDIO	0x1b0b0
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6ul-tqma6ul1.dtsi b/arch/arm/boot/dts/imx6ul-tqma6ul1.dtsi
new file mode 100644
index 000000000000..24192d012ef7
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ul-tqma6ul1.dtsi
@@ -0,0 +1,37 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2018-2022 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+#include "imx6ul-tqma6ul2.dtsi"
+
+/ {
+	model = "TQ-Systems TQMa6UL1 SoM";
+	compatible = "tq,imx6ul-tqma6ul1", "fsl,imx6ul";
+};
+
+/*
+ * There are no module specific differences compared to TQMa6UL2,
+ * only external interfaces differ
+ */
+
+/*
+ * Devices not available on i.MX6ULG1 and should not be enabled on
+ * mainboard level (again)
+ */
+&can2 {
+	status = "disabled";
+};
+
+&csi {
+	status = "disabled";
+};
+
+&fec2 {
+	status = "disabled";
+};
+
+&lcdif {
+	status = "disabled";
+};
diff --git a/arch/arm/boot/dts/imx6ul-tqma6ul2-mba6ulx.dts b/arch/arm/boot/dts/imx6ul-tqma6ul2-mba6ulx.dts
new file mode 100644
index 000000000000..0757df2b8f48
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ul-tqma6ul2-mba6ulx.dts
@@ -0,0 +1,15 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2018-2022 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+/dts-v1/;
+
+#include "imx6ul-tqma6ul2.dtsi"
+#include "mba6ulx.dtsi"
+
+/ {
+	model = "TQ-Systems TQMa6ULx SoM on MBa6ULx board";
+	compatible = "tq,imx6ul-tqma6ul2-mba6ulx", "tq,imx6ul-tqma6ul2", "fsl,imx6ul";
+};
diff --git a/arch/arm/boot/dts/imx6ul-tqma6ul2.dtsi b/arch/arm/boot/dts/imx6ul-tqma6ul2.dtsi
new file mode 100644
index 000000000000..e2e95dd92263
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ul-tqma6ul2.dtsi
@@ -0,0 +1,71 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2018-2022 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+#include "imx6ul.dtsi"
+#include "imx6ul-tqma6ul-common.dtsi"
+#include "imx6ul-tqma6ulx-common.dtsi"
+
+/ {
+	model = "TQ-Systems TQMa6UL2 SoM";
+	compatible = "tq,imx6ul-tqma6ul2", "fsl,imx6ul";
+};
+
+&usdhc2 {
+	fsl,tuning-step = <6>;
+};
+
+&iomuxc {
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK		0x00017051
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD		0x00017051
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0	0x00017051
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1	0x00017051
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2	0x00017051
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3	0x00017051
+			MX6UL_PAD_NAND_DATA04__USDHC2_DATA4	0x00017051
+			MX6UL_PAD_NAND_DATA05__USDHC2_DATA5	0x00017051
+			MX6UL_PAD_NAND_DATA06__USDHC2_DATA6	0x00017051
+			MX6UL_PAD_NAND_DATA07__USDHC2_DATA7	0x00017051
+			/* rst */
+			MX6UL_PAD_NAND_ALE__GPIO4_IO10		0x0001b051
+		>;
+	};
+
+	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK		0x000170e1
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD		0x000170f1
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0	0x000170f1
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1	0x000170f1
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2	0x000170f1
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3	0x000170f1
+			MX6UL_PAD_NAND_DATA04__USDHC2_DATA4	0x000170f1
+			MX6UL_PAD_NAND_DATA05__USDHC2_DATA5	0x000170f1
+			MX6UL_PAD_NAND_DATA06__USDHC2_DATA6	0x000170f1
+			MX6UL_PAD_NAND_DATA07__USDHC2_DATA7	0x000170f1
+			/* rst */
+			MX6UL_PAD_NAND_ALE__GPIO4_IO10		0x0001b051
+		>;
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK		0x000170f1
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD		0x000170e1
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0	0x000170e1
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1	0x000170e1
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2	0x000170e1
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3	0x000170e1
+			MX6UL_PAD_NAND_DATA04__USDHC2_DATA4	0x000170e1
+			MX6UL_PAD_NAND_DATA05__USDHC2_DATA5	0x000170e1
+			MX6UL_PAD_NAND_DATA06__USDHC2_DATA6	0x000170e1
+			MX6UL_PAD_NAND_DATA07__USDHC2_DATA7	0x000170e1
+			/* rst */
+			MX6UL_PAD_NAND_ALE__GPIO4_IO10		0x0001b051
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6ul-tqma6ul2l-mba6ulx.dts b/arch/arm/boot/dts/imx6ul-tqma6ul2l-mba6ulx.dts
new file mode 100644
index 000000000000..9d9b6b744a1c
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ul-tqma6ul2l-mba6ulx.dts
@@ -0,0 +1,15 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2018-2022 TQ Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+/dts-v1/;
+
+#include "imx6ul-tqma6ul2l.dtsi"
+#include "mba6ulx.dtsi"
+
+/ {
+	model = "TQ Systems TQMa6UL2L SoM on MBa6ULx board";
+	compatible = "tq,imx6ul-tqma6ul2l-mba6ulx", "tq,imx6ul-tqma6ul2l", "fsl,imx6ul";
+};
diff --git a/arch/arm/boot/dts/imx6ul-tqma6ul2l.dtsi b/arch/arm/boot/dts/imx6ul-tqma6ul2l.dtsi
new file mode 100644
index 000000000000..4b87e2dc70dc
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ul-tqma6ul2l.dtsi
@@ -0,0 +1,71 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2018-2022 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+#include "imx6ul.dtsi"
+#include "imx6ul-tqma6ul-common.dtsi"
+#include "imx6ul-tqma6ulxl-common.dtsi"
+
+/ {
+	model = "TQ-Systems TQMa6UL2L SoM";
+	compatible = "tq,imx6ul-tqma6ul2l", "fsl,imx6ul";
+};
+
+&usdhc2 {
+	fsl,tuning-step = <6>;
+};
+
+&iomuxc {
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK		0x00017051
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD		0x00017051
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0	0x00017051
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1	0x00017051
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2	0x00017051
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3	0x00017051
+			MX6UL_PAD_NAND_DATA04__USDHC2_DATA4	0x00017051
+			MX6UL_PAD_NAND_DATA05__USDHC2_DATA5	0x00017051
+			MX6UL_PAD_NAND_DATA06__USDHC2_DATA6	0x00017051
+			MX6UL_PAD_NAND_DATA07__USDHC2_DATA7	0x00017051
+			/* rst */
+			MX6UL_PAD_NAND_ALE__GPIO4_IO10		0x0001b051
+		>;
+	};
+
+	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK		0x000170e1
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD		0x000170f1
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0	0x000170f1
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1	0x000170f1
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2	0x000170f1
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3	0x000170f1
+			MX6UL_PAD_NAND_DATA04__USDHC2_DATA4	0x000170f1
+			MX6UL_PAD_NAND_DATA05__USDHC2_DATA5	0x000170f1
+			MX6UL_PAD_NAND_DATA06__USDHC2_DATA6	0x000170f1
+			MX6UL_PAD_NAND_DATA07__USDHC2_DATA7	0x000170f1
+			/* rst */
+			MX6UL_PAD_NAND_ALE__GPIO4_IO10		0x0001b051
+		>;
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK		0x000170f9
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD		0x000170f1
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0	0x000170f1
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1	0x000170f1
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2	0x000170f1
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3	0x000170f1
+			MX6UL_PAD_NAND_DATA04__USDHC2_DATA4	0x000170f1
+			MX6UL_PAD_NAND_DATA05__USDHC2_DATA5	0x000170f1
+			MX6UL_PAD_NAND_DATA06__USDHC2_DATA6	0x000170f1
+			MX6UL_PAD_NAND_DATA07__USDHC2_DATA7	0x000170f1
+			/* rst */
+			MX6UL_PAD_NAND_ALE__GPIO4_IO10		0x0001b051
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6ul-tqma6ulx-common.dtsi b/arch/arm/boot/dts/imx6ul-tqma6ulx-common.dtsi
new file mode 100644
index 000000000000..5afb9046c202
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ul-tqma6ulx-common.dtsi
@@ -0,0 +1,43 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2018-2022 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+/*
+ * Common for
+ * - TQMa6ULx
+ * - TQMa6ULLx
+ */
+
+&m24c64_50 {
+	vcc-supply = <&reg_sw2>;
+};
+
+&m24c02_52 {
+	vcc-supply = <&reg_sw2>;
+};
+
+&reg_sw2 {
+	regulator-boot-on;
+	regulator-always-on;
+};
+
+/* eMMC */
+&usdhc2 {
+	vmmc-supply = <&reg_sw2>;
+	vqmmc-supply = <&reg_vldo4>;
+};
+
+&iomuxc {
+	pinctrl_qspi: qspigrp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_WP_B__QSPI_A_SCLK      0x70b9
+			MX6UL_PAD_NAND_READY_B__QSPI_A_DATA00 0x70b9
+			MX6UL_PAD_NAND_CE0_B__QSPI_A_DATA01   0x70b9
+			MX6UL_PAD_NAND_CE1_B__QSPI_A_DATA02   0x70b9
+			MX6UL_PAD_NAND_CLE__QSPI_A_DATA03     0x70b9
+			MX6UL_PAD_NAND_DQS__QSPI_A_SS0_B      0x70a1
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6ul-tqma6ulxl-common.dtsi b/arch/arm/boot/dts/imx6ul-tqma6ulxl-common.dtsi
new file mode 100644
index 000000000000..ba84a4f70ebd
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ul-tqma6ulxl-common.dtsi
@@ -0,0 +1,48 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2018-2022 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+/*
+ * Common for
+ * - TQMa6ULxL
+ * - TQMa6ULLxL
+ */
+
+/ {
+	reg_vin: reg-vin {
+		compatible = "regulator-fixed";
+		regulator-name = "VIN";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+};
+
+&m24c64_50 {
+	vcc-supply = <&reg_vin>;
+};
+
+&m24c02_52 {
+	vcc-supply = <&reg_vin>;
+};
+
+/* eMMC */
+&usdhc2 {
+	vmmc-supply = <&reg_vin>;
+	vqmmc-supply = <&reg_vldo4>;
+};
+
+&iomuxc {
+	pinctrl_qspi: qspigrp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_WP_B__QSPI_A_SCLK      0x70a9
+			MX6UL_PAD_NAND_READY_B__QSPI_A_DATA00 0x70a9
+			MX6UL_PAD_NAND_CE0_B__QSPI_A_DATA01   0x70a9
+			MX6UL_PAD_NAND_CE1_B__QSPI_A_DATA02   0x70a9
+			MX6UL_PAD_NAND_CLE__QSPI_A_DATA03     0x70a9
+			MX6UL_PAD_NAND_DQS__QSPI_A_SS0_B      0x70a1
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6ul-tx6ul-mainboard.dts b/arch/arm/boot/dts/imx6ul-tx6ul-mainboard.dts
index 97686097a86e..92ac0edcb608 100644
--- a/arch/arm/boot/dts/imx6ul-tx6ul-mainboard.dts
+++ b/arch/arm/boot/dts/imx6ul-tx6ul-mainboard.dts
@@ -119,7 +119,7 @@
 	/delete-node/ codec@a;
 	/delete-node/ touchscreen@48;
 
-	rtc: mcp7940x@6f {
+	rtc: rtc@6f {
 		compatible = "microchip,mcp7940x";
 		reg = <0x6f>;
 	};
diff --git a/arch/arm/boot/dts/imx6ul-tx6ul.dtsi b/arch/arm/boot/dts/imx6ul-tx6ul.dtsi
index 938a32ced88d..15ee0275feaf 100644
--- a/arch/arm/boot/dts/imx6ul-tx6ul.dtsi
+++ b/arch/arm/boot/dts/imx6ul-tx6ul.dtsi
@@ -212,7 +212,7 @@
 		enable-active-high;
 	};
 
-	spi_gpio: spi-gpio {
+	spi_gpio: spi {
 		#address-cells = <1>;
 		#size-cells = <0>;
 		compatible = "spi-gpio";
@@ -227,18 +227,6 @@
 			&gpio1 10 GPIO_ACTIVE_HIGH
 		>;
 		status = "disabled";
-
-		spi@0 {
-			compatible = "spidev";
-			reg = <0>;
-			spi-max-frequency = <660000>;
-		};
-
-		spi@1 {
-			compatible = "spidev";
-			reg = <1>;
-			spi-max-frequency = <660000>;
-		};
 	};
 
 	sound {
@@ -290,18 +278,6 @@
 		&gpio1 10 GPIO_ACTIVE_HIGH
 	>;
 	status = "disabled";
-
-	spidev0: spi@0 {
-		compatible = "spidev";
-		reg = <0>;
-		spi-max-frequency = <60000000>;
-	};
-
-	spidev1: spi@1 {
-		compatible = "spidev";
-		reg = <1>;
-		spi-max-frequency = <60000000>;
-	};
 };
 
 &fec1 {
diff --git a/arch/arm/boot/dts/imx6ul.dtsi b/arch/arm/boot/dts/imx6ul.dtsi
index afeec01f6522..2b5996395701 100644
--- a/arch/arm/boot/dts/imx6ul.dtsi
+++ b/arch/arm/boot/dts/imx6ul.dtsi
@@ -64,20 +64,18 @@
 			clock-frequency = <696000000>;
 			clock-latency = <61036>; /* two CLK32 periods */
 			#cooling-cells = <2>;
-			operating-points = <
+			operating-points =
 				/* kHz	uV */
-				696000	1275000
-				528000	1175000
-				396000	1025000
-				198000	950000
-			>;
-			fsl,soc-operating-points = <
+				<696000	1275000>,
+				<528000	1175000>,
+				<396000	1025000>,
+				<198000	950000>;
+			fsl,soc-operating-points =
 				/* KHz	uV */
-				696000	1275000
-				528000	1175000
-				396000	1175000
-				198000	1175000
-			>;
+				<696000	1275000>,
+				<528000	1175000>,
+				<396000	1175000>,
+				<198000	1175000>;
 			clocks = <&clks IMX6UL_CLK_ARM>,
 				 <&clks IMX6UL_CLK_PLL2_BUS>,
 				 <&clks IMX6UL_CLK_PLL2_PFD2>,
@@ -139,7 +137,7 @@
 		interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>;
 	};
 
-	soc {
+	soc: soc {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "simple-bus";
@@ -149,6 +147,9 @@
 		ocram: sram@900000 {
 			compatible = "mmio-sram";
 			reg = <0x00900000 0x20000>;
+			ranges = <0 0x00900000 0x20000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 		};
 
 		intc: interrupt-controller@a01000 {
@@ -543,7 +544,7 @@
 			};
 
 			kpp: keypad@20b8000 {
-				compatible = "fsl,imx6ul-kpp", "fsl,imx6q-kpp", "fsl,imx21-kpp";
+				compatible = "fsl,imx6ul-kpp", "fsl,imx21-kpp";
 				reg = <0x020b8000 0x4000>;
 				interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks IMX6UL_CLK_KPP>;
@@ -743,7 +744,7 @@
 				status = "disabled";
 			};
 
-			sdma: sdma@20ec000 {
+			sdma: dma-controller@20ec000 {
 				compatible = "fsl,imx6ul-sdma", "fsl,imx6q-sdma",
 					     "fsl,imx35-sdma";
 				reg = <0x020ec000 0x4000>;
@@ -923,7 +924,6 @@
 				reg = <0x02198000 0x4000>;
 				interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks IMX6UL_CLK_ADC1>;
-				num-channels = <2>;
 				clock-names = "adc";
 				fsl,adck-max-frequency = <30000000>, <40000000>,
 							 <20000000>;
@@ -998,7 +998,7 @@
 			};
 
 			csi: csi@21c4000 {
-				compatible = "fsl,imx6ul-csi", "fsl,imx7-csi";
+				compatible = "fsl,imx6ul-csi";
 				reg = <0x021c4000 0x4000>;
 				interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks IMX6UL_CLK_CSI>;
@@ -1007,7 +1007,7 @@
 			};
 
 			lcdif: lcdif@21c8000 {
-				compatible = "fsl,imx6ul-lcdif", "fsl,imx28-lcdif";
+				compatible = "fsl,imx6ul-lcdif", "fsl,imx6sx-lcdif";
 				reg = <0x021c8000 0x4000>;
 				interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks IMX6UL_CLK_LCDIF_PIX>,
@@ -1028,7 +1028,7 @@
 			qspi: spi@21e0000 {
 				#address-cells = <1>;
 				#size-cells = <0>;
-				compatible = "fsl,imx6ul-qspi", "fsl,imx6sx-qspi";
+				compatible = "fsl,imx6ul-qspi";
 				reg = <0x021e0000 0x4000>, <0x60000000 0x10000000>;
 				reg-names = "QuadSPI", "QuadSPI-memory";
 				interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>;
diff --git a/arch/arm/boot/dts/imx6ull-colibri-aster.dts b/arch/arm/boot/dts/imx6ull-colibri-aster.dts
new file mode 100644
index 000000000000..d3f2fb7c6c1e
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ull-colibri-aster.dts
@@ -0,0 +1,20 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2017-2022 Toradex
+ */
+
+/dts-v1/;
+
+#include "imx6ull-colibri-nonwifi.dtsi"
+#include "imx6ull-colibri-aster.dtsi"
+
+/ {
+	model = "Toradex Colibri iMX6ULL 256/512MB on Colibri Aster";
+	compatible = "toradex,colibri-imx6ull-aster",
+		     "toradex,colibri-imx6ull",
+		     "fsl,imx6ull";
+};
+
+&atmel_mxt_ts {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6ull-colibri-aster.dtsi b/arch/arm/boot/dts/imx6ull-colibri-aster.dtsi
new file mode 100644
index 000000000000..c9133ba2d705
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ull-colibri-aster.dtsi
@@ -0,0 +1,145 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2017-2022 Toradex
+ */
+
+/ {
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_snvs_gpiokeys>;
+
+		power {
+			label = "Wake-Up";
+			gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;
+			linux,code = <KEY_WAKEUP>;
+			debounce-interval = <10>;
+			wakeup-source;
+		};
+	};
+
+	reg_3v3: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "3.3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	reg_5v0: regulator-5v0 {
+		compatible = "regulator-fixed";
+		regulator-name = "5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	reg_usbh_vbus: regulator-usbh-vbus {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usbh_reg>;
+		regulator-name = "VCC_USB[1-4]";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio1 2 GPIO_ACTIVE_LOW>;
+		vin-supply = <&reg_5v0>;
+	};
+};
+
+&adc1 {
+	status = "okay";
+};
+
+&ecspi1 {
+	status = "okay";
+
+	num-cs = <2>;
+	cs-gpios = <
+		&gpio3 26 GPIO_ACTIVE_HIGH /* SODIMM 86 LCD_DATA21 */
+		&gpio4 28 GPIO_ACTIVE_HIGH /* SODIMM 65 CSI_DATA07 */
+	>;
+};
+
+/*
+ * Following SODIMM Pins should not be accessed as GPIO on Aster board:
+ * 134 - AIN5_SCL (no connection)
+ * 127 - Voltage Level Translator OE# signal (IC11 and IC12)
+ *
+ * To configure GPIO to LED5, please disable FEC2 and uncomment the following:
+ *	&iomuxc {
+ *		pinctrl-names = "default";
+ *		pinctrl-0 = <
+ *			&pinctrl_gpio1
+ *			&pinctrl_gpio2
+ *			&pinctrl_gpio3
+ *			&pinctrl_gpio4
+ *			&pinctrl_gpio6 - for non-WiFi modules only
+ *			&pinctrl_gpio7
+ *			&pinctrl_gpio_aster
+ *		>;
+ *
+ *		pinctrl_gpio_aster: gpio-aster {
+ *			fsl,pins = <
+ *				MX6UL_PAD_GPIO1_IO07__GPIO1_IO07    0x1b0b0
+ *			>;
+ *		};
+ *  };
+ */
+
+&i2c1 {
+	status = "okay";
+
+	m41t0m6: rtc@68 {
+		compatible = "st,m41t0";
+		reg = <0x68>;
+	};
+};
+
+/* PWM <A> */
+&pwm4 {
+	status = "okay";
+};
+
+/* PWM <B> */
+&pwm5 {
+	status = "okay";
+};
+
+/* PWM <C> */
+&pwm6 {
+	status = "okay";
+};
+
+/* PWM <D> */
+&pwm7 {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&uart5 {
+	status = "okay";
+};
+
+&usbotg1 {
+	vbus-supply = <&reg_usbh_vbus>;
+	status = "okay";
+};
+
+&usbotg2 {
+	vbus-supply = <&reg_usbh_vbus>;
+	status = "okay";
+};
+
+&usdhc1 {
+	vmmc-supply = <&reg_3v3>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6ull-colibri-emmc-aster.dts b/arch/arm/boot/dts/imx6ull-colibri-emmc-aster.dts
new file mode 100644
index 000000000000..919c0464d6cb
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ull-colibri-emmc-aster.dts
@@ -0,0 +1,17 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/dts-v1/;
+
+#include "imx6ull-colibri-emmc-nonwifi.dtsi"
+#include "imx6ull-colibri-aster.dtsi"
+
+/ {
+	model = "Toradex Colibri iMX6ULL 1GB (eMMC) on Colibri Aster";
+	compatible = "toradex,colibri-imx6ull-emmc-aster",
+		     "toradex,colibri-imx6ull-emmc",
+		     "toradex,colibri-imx6ull",
+		     "fsl,imx6ull";
+};
diff --git a/arch/arm/boot/dts/imx6ull-colibri-emmc-iris-v2.dts b/arch/arm/boot/dts/imx6ull-colibri-emmc-iris-v2.dts
new file mode 100644
index 000000000000..b9060c2f7977
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ull-colibri-emmc-iris-v2.dts
@@ -0,0 +1,17 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/dts-v1/;
+
+#include "imx6ull-colibri-emmc-nonwifi.dtsi"
+#include "imx6ull-colibri-iris-v2.dtsi"
+
+/ {
+	model = "Toradex Colibri iMX6ULL 1G (eMMC) on Colibri Iris V2";
+	compatible = "toradex,colibri-imx6ull-iris-v2",
+		     "toradex,colibri-imx6ull-emmc",
+		     "toradex,colibri-imx6ull",
+		     "fsl,imx6ull";
+};
diff --git a/arch/arm/boot/dts/imx6ull-colibri-emmc-iris.dts b/arch/arm/boot/dts/imx6ull-colibri-emmc-iris.dts
new file mode 100644
index 000000000000..0ab71f2f5daa
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ull-colibri-emmc-iris.dts
@@ -0,0 +1,17 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/dts-v1/;
+
+#include "imx6ull-colibri-emmc-nonwifi.dtsi"
+#include "imx6ull-colibri-iris.dtsi"
+
+/ {
+	model = "Toradex Colibri iMX6ULL 1GB (eMMC) on Colibri Iris";
+	compatible = "toradex,colibri-imx6ull-emmc-iris",
+		     "toradex,colibri-imx6ull-emmc",
+		     "toradex,colibri-imx6ull",
+		     "fsl,imx6ull";
+};
diff --git a/arch/arm/boot/dts/imx6ull-colibri-emmc-nonwifi.dtsi b/arch/arm/boot/dts/imx6ull-colibri-emmc-nonwifi.dtsi
index a099abfdfa27..ea238525d5c0 100644
--- a/arch/arm/boot/dts/imx6ull-colibri-emmc-nonwifi.dtsi
+++ b/arch/arm/boot/dts/imx6ull-colibri-emmc-nonwifi.dtsi
@@ -1,6 +1,6 @@
-// SPDX-License-Identifier: GPL-2.0+ OR MIT
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
 /*
- * Copyright 2021 Toradex
+ * Copyright 2022 Toradex
  */
 
 #include "imx6ull-colibri.dtsi"
@@ -8,7 +8,7 @@
 / {
 	aliases {
 		mmc0 = &usdhc2; /* eMMC */
-		mmc1 = &usdhc1; /* MMC 4bit slot */
+		mmc1 = &usdhc1; /* MMC 4-bit slot */
 	};
 
 	memory@80000000 {
@@ -154,6 +154,7 @@
 			  "SODIMM_127";
 };
 
+/* NAND */
 &gpmi {
 	status = "disabled";
 };
@@ -170,6 +171,7 @@
 	pinctrl-0 = <&pinctrl_snvs_gpio1 &pinctrl_snvs_gpio3>;
 };
 
+/* eMMC */
 &usdhc2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_usdhc2emmc>;
diff --git a/arch/arm/boot/dts/imx6ull-colibri-eval-v3.dts b/arch/arm/boot/dts/imx6ull-colibri-eval-v3.dts
index 08669a18349e..9bf7111d7b00 100644
--- a/arch/arm/boot/dts/imx6ull-colibri-eval-v3.dts
+++ b/arch/arm/boot/dts/imx6ull-colibri-eval-v3.dts
@@ -1,6 +1,6 @@
-// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
 /*
- * Copyright 2018 Toradex AG
+ * Copyright 2018-2022 Toradex
  */
 
 /dts-v1/;
@@ -9,6 +9,6 @@
 #include "imx6ull-colibri-eval-v3.dtsi"
 
 / {
-	model = "Toradex Colibri iMX6ULL 256MB on Colibri Evaluation Board V3";
+	model = "Toradex Colibri iMX6ULL 256/512MB on Colibri Evaluation Board V3";
 	compatible = "toradex,colibri-imx6ull-eval", "fsl,imx6ull";
 };
diff --git a/arch/arm/boot/dts/imx6ull-colibri-eval-v3.dtsi b/arch/arm/boot/dts/imx6ull-colibri-eval-v3.dtsi
index a78849fd2afa..e29907428c20 100644
--- a/arch/arm/boot/dts/imx6ull-colibri-eval-v3.dtsi
+++ b/arch/arm/boot/dts/imx6ull-colibri-eval-v3.dtsi
@@ -1,6 +1,6 @@
-// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
 /*
- * Copyright 2017 Toradex AG
+ * Copyright 2017-2022 Toradex
  */
 
 / {
@@ -8,20 +8,6 @@
 		stdout-path = "serial0:115200n8";
 	};
 
-	gpio-keys {
-		compatible = "gpio-keys";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_snvs_gpiokeys>;
-
-		power {
-			label = "Wake-Up";
-			gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;
-			linux,code = <KEY_WAKEUP>;
-			debounce-interval = <10>;
-			wakeup-source;
-		};
-	};
-
 	/* fixed crystal dedicated to mcp2515 */
 	clk16m: clk16m {
 		compatible = "fixed-clock";
@@ -29,18 +15,6 @@
 		clock-frequency = <16000000>;
 	};
 
-	panel: panel {
-		compatible = "edt,et057090dhu";
-		backlight = <&bl>;
-		power-supply = <&reg_3v3>;
-
-		port {
-			panel_in: endpoint {
-				remote-endpoint = <&lcdif_out>;
-			};
-		};
-	};
-
 	reg_3v3: regulator-3v3 {
 		compatible = "regulator-fixed";
 		regulator-name = "3.3V";
@@ -71,14 +45,6 @@
 	status = "okay";
 };
 
-&bl {
-	brightness-levels = <0 4 8 16 32 64 128 255>;
-	default-brightness-level = <6>;
-	power-supply = <&reg_3v3>;
-	pwms = <&pwm4 0 5000000 1>;
-	status = "okay";
-};
-
 &ecspi1 {
 	status = "okay";
 
@@ -107,16 +73,6 @@
 	};
 };
 
-&lcdif {
-	status = "okay";
-
-	port {
-		lcdif_out: endpoint {
-			remote-endpoint = <&panel_in>;
-		};
-	};
-};
-
 /* PWM <A> */
 &pwm4 {
 	status = "okay";
@@ -150,6 +106,7 @@
 };
 
 &usbotg1 {
+	vbus-supply = <&reg_usbh_vbus>;
 	status = "okay";
 };
 
@@ -159,20 +116,6 @@
 };
 
 &usdhc1 {
-	pinctrl-names = "default", "state_100mhz", "state_200mhz", "sleep";
-	pinctrl-0 = <&pinctrl_usdhc1 &pinctrl_snvs_usdhc1_cd>;
-	pinctrl-1 = <&pinctrl_usdhc1_100mhz &pinctrl_snvs_usdhc1_cd>;
-	pinctrl-2 = <&pinctrl_usdhc1_200mhz &pinctrl_snvs_usdhc1_cd>;
-	pinctrl-3 = <&pinctrl_usdhc1 &pinctrl_snvs_usdhc1_sleep_cd>;
-	cd-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>;
-	disable-wp;
-	wakeup-source;
-	keep-power-in-suspend;
 	vmmc-supply = <&reg_3v3>;
-	vqmmc-supply = <&reg_sd1_vmmc>;
-	sd-uhs-sdr12;
-	sd-uhs-sdr25;
-	sd-uhs-sdr50;
-	sd-uhs-sdr104;
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/imx6ull-colibri-iris-v2.dts b/arch/arm/boot/dts/imx6ull-colibri-iris-v2.dts
new file mode 100644
index 000000000000..afc1e0119783
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ull-colibri-iris-v2.dts
@@ -0,0 +1,65 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2018-2022 Toradex
+ */
+
+/dts-v1/;
+
+#include "imx6ull-colibri-nonwifi.dtsi"
+#include "imx6ull-colibri-iris-v2.dtsi"
+
+/ {
+	model = "Toradex Colibri iMX6ULL 256M/512B on Colibri Iris V2";
+	compatible = "toradex,colibri-imx6ull-iris-v2",
+		     "toradex,colibri-imx6ull",
+		     "fsl,imx6ull";
+};
+
+&atmel_mxt_ts {
+	status = "okay";
+};
+
+&gpio1 {
+	/* This turns the LVDS transceiver on */
+	lvds-power-on {
+		gpio-hog;
+		gpios = <14 GPIO_ACTIVE_HIGH>; /* SODIMM 99 */
+		line-name = "LVDS_POWER_ON";
+		output-high;
+	};
+};
+
+&gpio2 {
+	/*
+	 * This switches the LVDS transceiver to the single-channel
+	 * output mode.
+	 */
+	lvds-ch-mode {
+		gpio-hog;
+		gpios = <0 GPIO_ACTIVE_HIGH>; /* SODIMM 55 */
+		line-name = "LVDS_CH_MODE";
+		output-high;
+	};
+
+	/*
+	 * This switches the LVDS transceiver to the 24-bit RGB mode.
+	 */
+	lvds-rgb-mode {
+		gpio-hog;
+		gpios = <1 GPIO_ACTIVE_HIGH>; /* SODIMM 63 */
+		line-name = "LVDS_RGB_MODE";
+		output-low;
+	};
+};
+
+&gpio5 {
+	/*
+	 * This switches the LVDS transceiver to VESA color mapping mode.
+	 */
+	lvds-color-map {
+		gpio-hog;
+		gpios = <3 GPIO_ACTIVE_HIGH>; /* SODIMM 95 */
+		line-name = "LVDS_COLOR_MAP";
+		output-low;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6ull-colibri-iris-v2.dtsi b/arch/arm/boot/dts/imx6ull-colibri-iris-v2.dtsi
new file mode 100644
index 000000000000..93649cad0cc0
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ull-colibri-iris-v2.dtsi
@@ -0,0 +1,27 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2018-2022 Toradex
+ */
+
+#include "imx6ull-colibri-iris.dtsi"
+
+/ {
+	reg_3v3_vmmc: regulator-3v3-vmmc {
+		compatible = "regulator-fixed";
+		regulator-name = "3v3_vmmc";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio1 26 GPIO_ACTIVE_HIGH>;
+		startup-delay-us = <100>;
+		enable-active-high;
+	};
+};
+
+
+&usdhc1 {
+	cap-power-off-card;
+	vmmc-supply = <&reg_3v3_vmmc>;
+	/delete-property/ keep-power-in-suspend;
+	/delete-property/ no-1-8-v;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6ull-colibri-iris.dts b/arch/arm/boot/dts/imx6ull-colibri-iris.dts
new file mode 100644
index 000000000000..4fb97b0fe30b
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ull-colibri-iris.dts
@@ -0,0 +1,20 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2018-2022 Toradex
+ */
+
+/dts-v1/;
+
+#include "imx6ull-colibri-nonwifi.dtsi"
+#include "imx6ull-colibri-iris.dtsi"
+
+/ {
+	model = "Toradex Colibri iMX6ULL 256/512MB on Colibri Iris";
+	compatible = "toradex,colibri-imx6ull-iris",
+		     "toradex,colibri-imx6ull",
+		     "fsl,imx6ull";
+};
+
+&atmel_mxt_ts {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6ull-colibri-iris.dtsi b/arch/arm/boot/dts/imx6ull-colibri-iris.dtsi
new file mode 100644
index 000000000000..7f3b37baba88
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ull-colibri-iris.dtsi
@@ -0,0 +1,132 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2018-2022 Toradex
+ */
+
+/ {
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_snvs_gpiokeys>;
+
+		power {
+			label = "Wake-Up";
+			gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;
+			linux,code = <KEY_WAKEUP>;
+			debounce-interval = <10>;
+			wakeup-source;
+		};
+	};
+
+	reg_3v3: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "3.3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	reg_5v0: regulator-5v0 {
+		compatible = "regulator-fixed";
+		regulator-name = "5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	reg_usbh_vbus: regulator-usbh-vbus {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usbh_reg>;
+		regulator-name = "VCC_USB[1-4]";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio1 2 GPIO_ACTIVE_LOW>;
+		vin-supply = <&reg_5v0>;
+	};
+};
+
+&adc1 {
+	status = "okay";
+};
+
+&gpio1 {
+	/*
+	 * uart25_tx_on turns the UART transceiver on. If one wants to turn the
+	 * transceiver off, that property has to be deleted and the gpio handled
+	 * in userspace.
+	 * The same applies to uart1_tx_on.
+	 */
+	uart25_tx_on {
+		gpio-hog;
+		gpios = <15 0>;
+		output-high;
+	};
+};
+
+&gpio2 {
+	uart1_tx_on {
+		gpio-hog;
+		gpios = <7 0>;
+		output-high;
+	};
+};
+
+&i2c1 {
+	status = "okay";
+
+	/* M41T0M6 real time clock on carrier board */
+	m41t0m6: rtc@68 {
+		compatible = "st,m41t0";
+		reg = <0x68>;
+	};
+};
+
+/* PWM <A> */
+&pwm4 {
+	status = "okay";
+};
+
+/* PWM <B> */
+&pwm5 {
+	status = "okay";
+};
+
+/* PWM <C> */
+&pwm6 {
+	status = "okay";
+};
+
+/* PWM <D> */
+&pwm7 {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&uart5 {
+	status = "okay";
+};
+
+&usbotg1 {
+	vbus-supply = <&reg_usbh_vbus>;
+	status = "okay";
+};
+
+&usbotg2 {
+	vbus-supply = <&reg_usbh_vbus>;
+	status = "okay";
+};
+
+&usdhc1 {
+	vmmc-supply = <&reg_3v3>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6ull-colibri-nonwifi.dtsi b/arch/arm/boot/dts/imx6ull-colibri-nonwifi.dtsi
index 95a11b8bcbdb..88901db255d6 100644
--- a/arch/arm/boot/dts/imx6ull-colibri-nonwifi.dtsi
+++ b/arch/arm/boot/dts/imx6ull-colibri-nonwifi.dtsi
@@ -1,6 +1,6 @@
-// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
 /*
- * Copyright 2018 Toradex AG
+ * Copyright 2018-2022 Toradex
  */
 
 #include "imx6ull-colibri.dtsi"
@@ -12,13 +12,150 @@
 	};
 };
 
+&gpio1 {
+	gpio-line-names = "SODIMM_8",
+			  "SODIMM_6",
+			  "SODIMM_129",
+			  "SODIMM_89",
+			  "SODIMM_19",
+			  "SODIMM_21",
+			  "UNUSABLE_SODIMM_180",
+			  "UNUSABLE_SODIMM_184",
+			  "SODIMM_4",
+			  "SODIMM_2",
+			  "SODIMM_106",
+			  "SODIMM_71",
+			  "SODIMM_23",
+			  "SODIMM_31",
+			  "SODIMM_99",
+			  "SODIMM_102",
+			  "SODIMM_33",
+			  "SODIMM_35",
+			  "SODIMM_25",
+			  "SODIMM_27",
+			  "SODIMM_36",
+			  "SODIMM_38",
+			  "SODIMM_32",
+			  "SODIMM_34",
+			  "SODIMM_135",
+			  "SODIMM_77",
+			  "SODIMM_100",
+			  "SODIMM_186",
+			  "SODIMM_196",
+			  "SODIMM_194";
+};
+
+&gpio2 {
+	gpio-line-names = "SODIMM_55",
+			  "SODIMM_63",
+			  "SODIMM_178",
+			  "SODIMM_188",
+			  "SODIMM_73",
+			  "SODIMM_30",
+			  "SODIMM_67",
+			  "SODIMM_104",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "SODIMM_190",
+			  "SODIMM_47",
+			  "SODIMM_192",
+			  "SODIMM_49",
+			  "SODIMM_51",
+			  "SODIMM_53";
+};
+
+&gpio3 {
+	gpio-line-names = "SODIMM_56",
+			  "SODIMM_44",
+			  "SODIMM_68",
+			  "SODIMM_82",
+			  "",
+			  "SODIMM_76",
+			  "SODIMM_70",
+			  "SODIMM_60",
+			  "SODIMM_58",
+			  "SODIMM_78",
+			  "SODIMM_72",
+			  "SODIMM_80",
+			  "SODIMM_46",
+			  "SODIMM_62",
+			  "SODIMM_48",
+			  "SODIMM_74",
+			  "SODIMM_50",
+			  "SODIMM_52",
+			  "SODIMM_54",
+			  "SODIMM_66",
+			  "SODIMM_64",
+			  "SODIMM_57",
+			  "SODIMM_61",
+			  "SODIMM_29",
+			  "SODIMM_37",
+			  "SODIMM_88",
+			  "SODIMM_86",
+			  "SODIMM_92",
+			  "SODIMM_90";
+};
+
+&gpio4 {
+	gpio-line-names = "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "SODIMM_59",
+			  "",
+			  "",
+			  "SODIMM_133",
+			  "",
+			  "SODIMM_28",
+			  "SODIMM_75",
+			  "SODIMM_96",
+			  "SODIMM_81",
+			  "SODIMM_94",
+			  "SODIMM_101",
+			  "SODIMM_103",
+			  "SODIMM_79",
+			  "SODIMM_97",
+			  "SODIMM_69",
+			  "SODIMM_98",
+			  "SODIMM_85",
+			  "SODIMM_65";
+};
+
+&gpio5 {
+	gpio-line-names = "SODIMM_43",
+			  "SODIMM_45",
+			  "SODIMM_137",
+			  "SODIMM_95",
+			  "SODIMM_107",
+			  "SODIMM_131",
+			  "SODIMM_93",
+			  "",
+			  "SODIMM_138",
+			  "",
+			  "SODIMM_105",
+			  "SODIMM_127";
+};
+
 &iomuxc {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_gpio1 &pinctrl_gpio2 &pinctrl_gpio3
-		&pinctrl_gpio4 &pinctrl_gpio5 &pinctrl_gpio6 &pinctrl_gpio7>;
+		&pinctrl_gpio4 &pinctrl_gpio6 &pinctrl_gpio7>;
 };
 
 &iomuxc_snvs {
 	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_snvs_gpio1 &pinctrl_snvs_gpio2 &pinctrl_snvs_gpio3>;
+	pinctrl-0 = <&pinctrl_snvs_gpio1 &pinctrl_snvs_gpio3>;
 };
diff --git a/arch/arm/boot/dts/imx6ull-colibri-wifi-aster.dts b/arch/arm/boot/dts/imx6ull-colibri-wifi-aster.dts
new file mode 100644
index 000000000000..b4f65e8c5857
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ull-colibri-wifi-aster.dts
@@ -0,0 +1,20 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2017-2022 Toradex
+ */
+
+/dts-v1/;
+
+#include "imx6ull-colibri-wifi.dtsi"
+#include "imx6ull-colibri-aster.dtsi"
+
+/ {
+	model = "Toradex Colibri iMX6ULL 512MB on Colibri Aster";
+	compatible = "toradex,colibri-imx6ull-wifi-aster",
+		     "toradex,colibri-imx6ull",
+		     "fsl,imx6ull";
+};
+
+&atmel_mxt_ts {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6ull-colibri-wifi-eval-v3.dts b/arch/arm/boot/dts/imx6ull-colibri-wifi-eval-v3.dts
index df72ce1ae2cb..1d64d1a5d8a7 100644
--- a/arch/arm/boot/dts/imx6ull-colibri-wifi-eval-v3.dts
+++ b/arch/arm/boot/dts/imx6ull-colibri-wifi-eval-v3.dts
@@ -1,6 +1,6 @@
-// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
 /*
- * Copyright 2018 Toradex AG
+ * Copyright 2018-2022 Toradex
  */
 
 /dts-v1/;
diff --git a/arch/arm/boot/dts/imx6ull-colibri-wifi-iris-v2.dts b/arch/arm/boot/dts/imx6ull-colibri-wifi-iris-v2.dts
new file mode 100644
index 000000000000..ce02f8a9ddd3
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ull-colibri-wifi-iris-v2.dts
@@ -0,0 +1,65 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2018-2022 Toradex
+ */
+
+/dts-v1/;
+
+#include "imx6ull-colibri-wifi.dtsi"
+#include "imx6ull-colibri-iris-v2.dtsi"
+
+/ {
+	model = "Toradex Colibri iMX6ULL 512MB on Colibri Iris V2";
+	compatible = "toradex,colibri-imx6ull-wifi-iris-v2",
+		     "toradex,colibri-imx6ull",
+		     "fsl,imx6ull";
+};
+
+&atmel_mxt_ts {
+	status = "okay";
+};
+
+&gpio1 {
+	/* This turns the LVDS transceiver on */
+	lvds-power-on {
+		gpio-hog;
+		gpios = <14 GPIO_ACTIVE_HIGH>; /* SODIMM 99 */
+		line-name = "LVDS_POWER_ON";
+		output-high;
+	};
+};
+
+&gpio2 {
+	/*
+	 * This switches the LVDS transceiver to the single-channel
+	 * output mode.
+	 */
+	lvds-ch-mode {
+		gpio-hog;
+		gpios = <0 GPIO_ACTIVE_HIGH>; /* SODIMM 55 */
+		line-name = "LVDS_CH_MODE";
+		output-high;
+	};
+
+	/*
+	 * This switches the LVDS transceiver to the 24-bit RGB mode.
+	 */
+	lvds-rgb-mode {
+		gpio-hog;
+		gpios = <1 GPIO_ACTIVE_HIGH>; /* SODIMM 63 */
+		line-name = "LVDS_RGB_MODE";
+		output-low;
+	};
+};
+
+&gpio5 {
+	/*
+	 * This switches the LVDS transceiver to VESA color mapping mode.
+	 */
+	lvds-color-map {
+		gpio-hog;
+		gpios = <3 GPIO_ACTIVE_HIGH>; /* SODIMM 95 */
+		line-name = "LVDS_COLOR_MAP";
+		output-low;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6ull-colibri-wifi-iris.dts b/arch/arm/boot/dts/imx6ull-colibri-wifi-iris.dts
new file mode 100644
index 000000000000..5ac1aa298ce7
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ull-colibri-wifi-iris.dts
@@ -0,0 +1,20 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2018-2022 Toradex
+ */
+
+/dts-v1/;
+
+#include "imx6ull-colibri-wifi.dtsi"
+#include "imx6ull-colibri-iris.dtsi"
+
+/ {
+	model = "Toradex Colibri iMX6ULL 512MB on Colibri Iris";
+	compatible = "toradex,colibri-imx6ull-wifi-iris",
+		     "toradex,colibri-imx6ull",
+		     "fsl,imx6ull";
+};
+
+&atmel_mxt_ts {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6ull-colibri-wifi.dtsi b/arch/arm/boot/dts/imx6ull-colibri-wifi.dtsi
index 9f1e38282bee..db59ee6b1c86 100644
--- a/arch/arm/boot/dts/imx6ull-colibri-wifi.dtsi
+++ b/arch/arm/boot/dts/imx6ull-colibri-wifi.dtsi
@@ -1,6 +1,6 @@
-// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
 /*
- * Copyright 2018 Toradex AG
+ * Copyright 2018-2022 Toradex
  */
 
 #include "imx6ull-colibri.dtsi"
@@ -23,16 +23,152 @@
 	clock-frequency = <792000000>;
 };
 
+&gpio1 {
+	gpio-line-names = "SODIMM_8",
+			  "SODIMM_6",
+			  "SODIMM_129",
+			  "",
+			  "SODIMM_19",
+			  "SODIMM_21",
+			  "UNUSABLE_SODIMM_180",
+			  "UNUSABLE_SODIMM_184",
+			  "SODIMM_4",
+			  "SODIMM_2",
+			  "SODIMM_106",
+			  "SODIMM_71",
+			  "SODIMM_23",
+			  "SODIMM_31",
+			  "SODIMM_99",
+			  "SODIMM_102",
+			  "SODIMM_33",
+			  "SODIMM_35",
+			  "SODIMM_25",
+			  "SODIMM_27",
+			  "SODIMM_36",
+			  "SODIMM_38",
+			  "SODIMM_32",
+			  "SODIMM_34",
+			  "SODIMM_135",
+			  "SODIMM_77",
+			  "SODIMM_100",
+			  "SODIMM_186",
+			  "SODIMM_196",
+			  "SODIMM_194";
+};
+
+&gpio2 {
+	gpio-line-names = "SODIMM_55",
+			  "SODIMM_63",
+			  "SODIMM_178",
+			  "SODIMM_188",
+			  "SODIMM_73",
+			  "SODIMM_30",
+			  "SODIMM_67",
+			  "SODIMM_104",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "SODIMM_190",
+			  "SODIMM_47",
+			  "SODIMM_192",
+			  "SODIMM_49",
+			  "SODIMM_51",
+			  "SODIMM_53";
+};
+
+&gpio3 {
+	gpio-line-names = "SODIMM_56",
+			  "SODIMM_44",
+			  "SODIMM_68",
+			  "SODIMM_82",
+			  "",
+			  "SODIMM_76",
+			  "SODIMM_70",
+			  "SODIMM_60",
+			  "SODIMM_58",
+			  "SODIMM_78",
+			  "SODIMM_72",
+			  "SODIMM_80",
+			  "SODIMM_46",
+			  "SODIMM_62",
+			  "SODIMM_48",
+			  "SODIMM_74",
+			  "SODIMM_50",
+			  "SODIMM_52",
+			  "SODIMM_54",
+			  "SODIMM_66",
+			  "SODIMM_64",
+			  "SODIMM_57",
+			  "SODIMM_61",
+			  "SODIMM_29",
+			  "SODIMM_37",
+			  "SODIMM_88",
+			  "SODIMM_86",
+			  "SODIMM_92",
+			  "SODIMM_90";
+};
+
+&gpio4 {
+	gpio-line-names = "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "SODIMM_59",
+			  "",
+			  "",
+			  "SODIMM_133",
+			  "",
+			  "SODIMM_28",
+			  "SODIMM_75",
+			  "SODIMM_96",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "SODIMM_69",
+			  "SODIMM_98",
+			  "SODIMM_85",
+			  "SODIMM_65";
+};
+
+&gpio5 {
+	gpio-line-names = "SODIMM_43",
+			  "SODIMM_45",
+			  "SODIMM_137",
+			  "SODIMM_95",
+			  "SODIMM_107",
+			  "SODIMM_131",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "SODIMM_105";
+};
+
 &iomuxc {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_gpio1 &pinctrl_gpio2 &pinctrl_gpio3
-		&pinctrl_gpio4 &pinctrl_gpio5 &pinctrl_gpio7>;
+		&pinctrl_gpio4 &pinctrl_gpio7>;
 
 };
 
 &iomuxc_snvs {
 	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_snvs_gpio1 &pinctrl_snvs_gpio2>;
+	pinctrl-0 = <&pinctrl_snvs_gpio1>;
 };
 
 &usdhc2 {
diff --git a/arch/arm/boot/dts/imx6ull-colibri.dtsi b/arch/arm/boot/dts/imx6ull-colibri.dtsi
index 7f35a06dff95..577a424b0e1d 100644
--- a/arch/arm/boot/dts/imx6ull-colibri.dtsi
+++ b/arch/arm/boot/dts/imx6ull-colibri.dtsi
@@ -1,22 +1,54 @@
-// SPDX-License-Identifier: GPL-2.0+ OR MIT
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
 /*
- * Copyright 2018-2021 Toradex
+ * Copyright 2018-2022 Toradex
  */
 
 #include "imx6ull.dtsi"
 
 / {
+	/* Ethernet aliases to ensure correct MAC addresses */
 	aliases {
 		ethernet0 = &fec2;
 		ethernet1 = &fec1;
 	};
 
-	bl: backlight {
+	backlight: backlight {
 		compatible = "pwm-backlight";
+		brightness-levels = <0 4 8 16 32 64 128 255>;
+		default-brightness-level = <6>;
+		enable-gpios = <&gpio1 11 GPIO_ACTIVE_HIGH>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gpio_bl_on>;
-		enable-gpios = <&gpio1 11 GPIO_ACTIVE_HIGH>;
-		status = "disabled";
+		power-supply = <&reg_3v3>;
+		pwms = <&pwm4 0 5000000 1>;
+		status = "okay";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_snvs_gpiokeys>;
+
+		wakeup {
+			debounce-interval = <10>;
+			gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>; /* SODIMM 45 */
+			label = "Wake-Up";
+			linux,code = <KEY_WAKEUP>;
+			wakeup-source;
+		};
+	};
+
+	panel_dpi: panel-dpi {
+		compatible = "edt,et057090dhu";
+		backlight = <&backlight>;
+		power-supply = <&reg_3v3>;
+		status = "okay";
+
+		port {
+			lcd_panel_in: endpoint {
+				remote-endpoint = <&lcdif_out>;
+			};
+		};
 	};
 
 	reg_module_3v3: regulator-module-3v3 {
@@ -35,9 +67,9 @@
 		regulator-max-microvolt = <3300000>;
 	};
 
-	reg_sd1_vmmc: regulator-sd1-vmmc {
+	reg_sd1_vqmmc: regulator-sd1-vqmmc {
 		compatible = "regulator-gpio";
-		gpio = <&gpio5 9 GPIO_ACTIVE_HIGH>;
+		gpios = <&gpio5 9 GPIO_ACTIVE_HIGH>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_snvs_reg_sd>;
 		regulator-always-on;
@@ -47,11 +79,24 @@
 		states = <1800000 0x1 3300000 0x0>;
 		vin-supply = <&reg_module_3v3>;
 	};
+
+	reg_eth_phy: regulator-eth-phy {
+		compatible = "regulator-fixed-clock";
+		regulator-boot-on;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-name = "+V3.3_ETH";
+		regulator-type = "voltage";
+		vin-supply = <&reg_module_3v3>;
+		clocks = <&clks IMX6UL_CLK_ENET2_REF_125M>;
+		startup-delay-us = <150000>;
+	};
 };
 
 &adc1 {
-	num-channels = <10>;
 	vref-supply = <&reg_module_3v3_avdd>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_adc1>;
 };
 
 &can1 {
@@ -73,12 +118,14 @@
 	pinctrl-0 = <&pinctrl_ecspi1 &pinctrl_ecspi1_cs>;
 };
 
+/* Ethernet */
 &fec2 {
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&pinctrl_enet2>;
 	pinctrl-1 = <&pinctrl_enet2_sleep>;
 	phy-mode = "rmii";
 	phy-handle = <&ethphy1>;
+	phy-supply = <&reg_eth_phy>;
 	status = "okay";
 
 	mdio {
@@ -93,9 +140,11 @@
 	};
 };
 
+/* NAND */
 &gpmi {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_gpmi_nand>;
+	fsl,use-minimum-ecc;
 	nand-on-flash-bbt;
 	nand-ecc-mode = "hw";
 	nand-ecc-strength = <8>;
@@ -103,15 +152,35 @@
 	status = "okay";
 };
 
+/* I2C3_SDA/SCL on SODIMM 194/196 (e.g. RTC on carrier board) */
 &i2c1 {
 	pinctrl-names = "default", "gpio";
 	pinctrl-0 = <&pinctrl_i2c1>;
 	pinctrl-1 = <&pinctrl_i2c1_gpio>;
 	sda-gpios = <&gpio1 29 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 	scl-gpios = <&gpio1 28 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "okay";
+
+	/* Atmel maxtouch controller */
+	atmel_mxt_ts: touchscreen@4a {
+		compatible = "atmel,maxtouch";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_atmel_conn &pinctrl_atmel_snvs_conn>;
+		reg = <0x4a>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <4 IRQ_TYPE_EDGE_FALLING>;       /* SODIMM 107 / INT */
+		reset-gpios = <&gpio1 10 GPIO_ACTIVE_LOW>;    /* SODIMM 106 / RST */
+		status = "disabled";
+	};
 };
 
+/*
+ * PWR_I2C: power I2C to audio codec, PMIC, temperature sensor and
+ * touch screen controller
+ */
 &i2c2 {
+	/* Use low frequency to compensate for the high pull-up values. */
+	clock-frequency = <40000>;
 	pinctrl-names = "default", "gpio";
 	pinctrl-0 = <&pinctrl_i2c2>;
 	pinctrl-1 = <&pinctrl_i2c2_gpio>;
@@ -119,7 +188,7 @@
 	scl-gpios = <&gpio1 30 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 	status = "okay";
 
-	ad7879@2c {
+	ad7879_ts: touchscreen@2c {
 		compatible = "adi,ad7879-1";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_snvs_ad7879_int>;
@@ -140,23 +209,33 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_lcdif_dat
 		     &pinctrl_lcdif_ctrl>;
+
+	port {
+		lcdif_out: endpoint {
+			remote-endpoint = <&lcd_panel_in>;
+		};
+	};
 };
 
+/* PWM <A> */
 &pwm4 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm4>;
 };
 
+/* PWM <B> */
 &pwm5 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm5>;
 };
 
+/* PWM <C> */
 &pwm6 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm6>;
 };
 
+/* PWM <D> */
 &pwm7 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm7>;
@@ -170,6 +249,7 @@
 	status = "disabled";
 };
 
+/* Colibri UART_A */
 &uart1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart1 &pinctrl_uart1_ctrl1>;
@@ -177,6 +257,7 @@
 	fsl,dte-mode;
 };
 
+/* Colibri UART_B */
 &uart2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart2>;
@@ -184,12 +265,14 @@
 	fsl,dte-mode;
 };
 
+/* Colibri UART_C */
 &uart5 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart5>;
 	fsl,dte-mode;
 };
 
+/* Colibri USBC */
 &usbotg1 {
 	dr_mode = "otg";
 	srp-disable;
@@ -197,14 +280,28 @@
 	adp-disable;
 };
 
+/* Colibri USBH */
 &usbotg2 {
 	dr_mode = "host";
 };
 
+/* Colibri MMC/SD */
 &usdhc1 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz", "sleep";
+	pinctrl-0 = <&pinctrl_usdhc1 &pinctrl_snvs_usdhc1_cd>;
+	pinctrl-1 = <&pinctrl_usdhc1_100mhz &pinctrl_snvs_usdhc1_cd>;
+	pinctrl-2 = <&pinctrl_usdhc1_200mhz &pinctrl_snvs_usdhc1_cd>;
+	pinctrl-3 = <&pinctrl_usdhc1 &pinctrl_snvs_usdhc1_cd_sleep>;
 	assigned-clocks = <&clks IMX6UL_CLK_USDHC1_SEL>, <&clks IMX6UL_CLK_USDHC1>;
 	assigned-clock-parents = <&clks IMX6UL_CLK_PLL2_PFD2>;
 	assigned-clock-rates = <0>, <198000000>;
+	bus-width = <4>;
+	cd-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>; /* MMC_CD */
+	disable-wp;
+	keep-power-in-suspend;
+	no-1-8-v;
+	vqmmc-supply = <&reg_sd1_vqmmc>;
+	wakeup-source;
 };
 
 &wdog1 {
@@ -214,13 +311,35 @@
 };
 
 &iomuxc {
-	pinctrl_can_int: canint-grp {
+	pinctrl_adc1: adc1grp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO00__GPIO1_IO00        0x3000 /* SODIMM 8 */
+			MX6UL_PAD_GPIO1_IO01__GPIO1_IO01        0x3000 /* SODIMM 6 */
+			MX6UL_PAD_GPIO1_IO08__GPIO1_IO08        0x3000 /* SODIMM 4 */
+			MX6UL_PAD_GPIO1_IO09__GPIO1_IO09        0x3000 /* SODIMM 2 */
+		>;
+	};
+
+	pinctrl_atmel_adap: atmeladapgrp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_DQS__GPIO4_IO16          0xb0a0  /* SODIMM 28 */
+			MX6UL_PAD_ENET1_TX_EN__GPIO2_IO05       0xb0a0  /* SODIMM 30 */
+		>;
+	};
+
+	pinctrl_atmel_conn: atmelconngrp {
+		fsl,pins = <
+			MX6UL_PAD_JTAG_MOD__GPIO1_IO10          0xb0a0  /* SODIMM 106 */
+		>;
+	};
+
+	pinctrl_can_int: canintgrp {
 		fsl,pins = <
 			MX6UL_PAD_ENET1_TX_DATA1__GPIO2_IO04	0x13010	/* SODIMM 73 */
 		>;
 	};
 
-	pinctrl_enet2: enet2-grp {
+	pinctrl_enet2: enet2grp {
 		fsl,pins = <
 			MX6UL_PAD_GPIO1_IO06__ENET2_MDIO	0x1b0b0
 			MX6UL_PAD_GPIO1_IO07__ENET2_MDC		0x1b0b0
@@ -235,7 +354,7 @@
 		>;
 	};
 
-	pinctrl_enet2_sleep: enet2sleepgrp {
+	pinctrl_enet2_sleep: enet2-sleepgrp {
 		fsl,pins = <
 			MX6UL_PAD_GPIO1_IO06__GPIO1_IO06	0x0
 			MX6UL_PAD_GPIO1_IO07__GPIO1_IO07	0x0
@@ -250,13 +369,13 @@
 		>;
 	};
 
-	pinctrl_ecspi1_cs: ecspi1-cs-grp {
+	pinctrl_ecspi1_cs: ecspi1csgrp {
 		fsl,pins = <
 			MX6UL_PAD_LCD_DATA21__GPIO3_IO26	0x70a0	/* SODIMM 86 */
 		>;
 	};
 
-	pinctrl_ecspi1: ecspi1-grp {
+	pinctrl_ecspi1: ecspi1grp {
 		fsl,pins = <
 			MX6UL_PAD_LCD_DATA20__ECSPI1_SCLK	0x000a0	/* SODIMM 88 */
 			MX6UL_PAD_LCD_DATA22__ECSPI1_MOSI	0x000a0 /* SODIMM 92 */
@@ -264,27 +383,27 @@
 		>;
 	};
 
-	pinctrl_flexcan1: flexcan1-grp {
+	pinctrl_flexcan1: flexcan1grp {
 		fsl,pins = <
 			MX6UL_PAD_ENET1_RX_DATA0__FLEXCAN1_TX	0x1b020
 			MX6UL_PAD_ENET1_RX_DATA1__FLEXCAN1_RX	0x1b020
 		>;
 	};
 
-	pinctrl_flexcan2: flexcan2-grp {
+	pinctrl_flexcan2: flexcan2grp {
 		fsl,pins = <
 			MX6UL_PAD_ENET1_TX_DATA0__FLEXCAN2_RX	0x1b020
 			MX6UL_PAD_ENET1_RX_EN__FLEXCAN2_TX	0x1b020
 		>;
 	};
 
-	pinctrl_gpio_bl_on: gpio-bl-on-grp {
+	pinctrl_gpio_bl_on: gpioblongrp {
 		fsl,pins = <
 			MX6UL_PAD_JTAG_TMS__GPIO1_IO11		0x30a0	/* SODIMM 71 */
 		>;
 	};
 
-	pinctrl_gpio1: gpio1-grp {
+	pinctrl_gpio1: gpio1grp {
 		fsl,pins = <
 			MX6UL_PAD_UART3_RX_DATA__GPIO1_IO25	0x10b0 /* SODIMM 77 */
 			MX6UL_PAD_JTAG_TCK__GPIO1_IO14		0x70a0 /* SODIMM 99 */
@@ -297,7 +416,7 @@
 		>;
 	};
 
-	pinctrl_gpio2: gpio2-grp { /* Camera */
+	pinctrl_gpio2: gpio2grp { /* Camera */
 		fsl,pins = <
 			MX6UL_PAD_CSI_DATA04__GPIO4_IO25	0x10b0 /* SODIMM 69 */
 			MX6UL_PAD_CSI_MCLK__GPIO4_IO17		0x10b0 /* SODIMM 75 */
@@ -307,26 +426,20 @@
 		>;
 	};
 
-	pinctrl_gpio3: gpio3-grp { /* CAN2 */
+	pinctrl_gpio3: gpio3grp { /* CAN2 */
 		fsl,pins = <
 			MX6UL_PAD_ENET1_RX_EN__GPIO2_IO02	0x10b0 /* SODIMM 178 */
 			MX6UL_PAD_ENET1_TX_DATA0__GPIO2_IO03	0x10b0 /* SODIMM 188 */
 		>;
 	};
 
-	pinctrl_gpio4: gpio4-grp {
+	pinctrl_gpio4: gpio4grp {
 		fsl,pins = <
 			MX6UL_PAD_CSI_DATA07__GPIO4_IO28	0x10b0 /* SODIMM 65 */
 		>;
 	};
 
-	pinctrl_gpio5: gpio5-grp { /* ATMEL MXT TOUCH */
-		fsl,pins = <
-			MX6UL_PAD_JTAG_MOD__GPIO1_IO10		0xb0a0 /* SODIMM 106 */
-		>;
-	};
-
-	pinctrl_gpio6: gpio6-grp { /* Wifi pins */
+	pinctrl_gpio6: gpio6grp { /* Wifi pins */
 		fsl,pins = <
 			MX6UL_PAD_GPIO1_IO03__GPIO1_IO03	0x10b0 /* SODIMM 89 */
 			MX6UL_PAD_CSI_DATA02__GPIO4_IO23	0x10b0 /* SODIMM 79 */
@@ -338,7 +451,7 @@
 		>;
 	};
 
-	pinctrl_gpio7: gpio7-grp { /* CAN1 */
+	pinctrl_gpio7: gpio7grp { /* CAN1 */
 		fsl,pins = <
 			MX6UL_PAD_ENET1_RX_DATA0__GPIO2_IO00	0xb0b0/* SODIMM 55 */
 			MX6UL_PAD_ENET1_RX_DATA1__GPIO2_IO01	0xb0b0 /* SODIMM 63 */
@@ -347,9 +460,9 @@
 
 	/*
 	 * With an eMMC instead of a raw NAND device the following pins
-	 * are available at SODIMM pins
+	 * are available at SODIMM pins.
 	 */
-	pinctrl_gpmi_gpio: gpmi-gpio-grp {
+	pinctrl_gpmi_gpio: gpmigpiogrp {
 		fsl,pins = <
 			MX6UL_PAD_NAND_ALE__GPIO4_IO10		0x10b0 /* SODIMM 140 */
 			MX6UL_PAD_NAND_CE0_B__GPIO4_IO13	0x10b0 /* SODIMM 144 */
@@ -358,7 +471,7 @@
 		>;
 	};
 
-	pinctrl_gpmi_nand: gpmi-nand-grp {
+	pinctrl_gpmi_nand: gpminandgrp {
 		fsl,pins = <
 			MX6UL_PAD_NAND_DATA00__RAWNAND_DATA00	0x100a9
 			MX6UL_PAD_NAND_DATA01__RAWNAND_DATA01	0x100a9
@@ -377,35 +490,35 @@
 		>;
 	};
 
-	pinctrl_i2c1: i2c1-grp {
+	pinctrl_i2c1: i2c1grp {
 		fsl,pins = <
 			MX6UL_PAD_UART4_TX_DATA__I2C1_SCL 0x4001b8b0	/* SODIMM 196 */
 			MX6UL_PAD_UART4_RX_DATA__I2C1_SDA 0x4001b8b0	/* SODIMM 194 */
 		>;
 	};
 
-	pinctrl_i2c1_gpio: i2c1-gpio-grp {
+	pinctrl_i2c1_gpio: i2c1-gpiogrp {
 		fsl,pins = <
 			MX6UL_PAD_UART4_TX_DATA__GPIO1_IO28 0x4001b8b0	/* SODIMM 196 */
 			MX6UL_PAD_UART4_RX_DATA__GPIO1_IO29 0x4001b8b0	/* SODIMM 194 */
 		>;
 	};
 
-	pinctrl_i2c2: i2c2-grp {
+	pinctrl_i2c2: i2c2grp {
 		fsl,pins = <
-			MX6UL_PAD_UART5_TX_DATA__I2C2_SCL 0x4001b8b0
-			MX6UL_PAD_UART5_RX_DATA__I2C2_SDA 0x4001b8b0
+			MX6UL_PAD_UART5_TX_DATA__I2C2_SCL 0x4001f8b0
+			MX6UL_PAD_UART5_RX_DATA__I2C2_SDA 0x4001f8b0
 		>;
 	};
 
-	pinctrl_i2c2_gpio: i2c2-gpio-grp {
+	pinctrl_i2c2_gpio: i2c2-gpiogrp {
 		fsl,pins = <
-			MX6UL_PAD_UART5_TX_DATA__GPIO1_IO30 0x4001b8b0
-			MX6UL_PAD_UART5_RX_DATA__GPIO1_IO31 0x4001b8b0
+			MX6UL_PAD_UART5_TX_DATA__GPIO1_IO30 0x4001f8b0
+			MX6UL_PAD_UART5_RX_DATA__GPIO1_IO31 0x4001f8b0
 		>;
 	};
 
-	pinctrl_lcdif_dat: lcdif-dat-grp {
+	pinctrl_lcdif_dat: lcdifdatgrp {
 		fsl,pins = <
 			MX6UL_PAD_LCD_DATA00__LCDIF_DATA00 0x00079	/* SODIMM 76 */
 			MX6UL_PAD_LCD_DATA01__LCDIF_DATA01 0x00079	/* SODIMM 70 */
@@ -428,7 +541,7 @@
 		>;
 	};
 
-	pinctrl_lcdif_ctrl: lcdif-ctrl-grp {
+	pinctrl_lcdif_ctrl: lcdifctrlgrp {
 		fsl,pins = <
 			MX6UL_PAD_LCD_CLK__LCDIF_CLK	    0x00079	/* SODIMM 56 */
 			MX6UL_PAD_LCD_ENABLE__LCDIF_ENABLE  0x00079	/* SODIMM 44 */
@@ -437,31 +550,31 @@
 		>;
 	};
 
-	pinctrl_pwm4: pwm4-grp {
+	pinctrl_pwm4: pwm4grp {
 		fsl,pins = <
 			MX6UL_PAD_NAND_WP_B__PWM4_OUT	0x00079		/* SODIMM 59 */
 		>;
 	};
 
-	pinctrl_pwm5: pwm5-grp {
+	pinctrl_pwm5: pwm5grp {
 		fsl,pins = <
 			MX6UL_PAD_NAND_DQS__PWM5_OUT	0x00079		/* SODIMM 28 */
 		>;
 	};
 
-	pinctrl_pwm6: pwm6-grp {
+	pinctrl_pwm6: pwm6grp {
 		fsl,pins = <
 			MX6UL_PAD_ENET1_TX_EN__PWM6_OUT	0x00079		/* SODIMM 30 */
 		>;
 	};
 
-	pinctrl_pwm7: pwm7-grp {
+	pinctrl_pwm7: pwm7grp {
 		fsl,pins = <
 			MX6UL_PAD_ENET1_TX_CLK__PWM7_OUT	0x00079	/* SODIMM 67 */
 		>;
 	};
 
-	pinctrl_uart1: uart1-grp {
+	pinctrl_uart1: uart1grp {
 		fsl,pins = <
 			MX6UL_PAD_UART1_TX_DATA__UART1_DTE_RX	0x1b0b1	/* SODIMM 33 */
 			MX6UL_PAD_UART1_RX_DATA__UART1_DTE_TX	0x1b0b1	/* SODIMM 35 */
@@ -470,16 +583,16 @@
 		>;
 	};
 
-	pinctrl_uart1_ctrl1: uart1-ctrl1-grp { /* Additional DTR, DCD */
+	pinctrl_uart1_ctrl1: uart1ctrl1grp { /* Additional DTR, DCD */
 		fsl,pins = <
-			MX6UL_PAD_JTAG_TDI__GPIO1_IO13		0x70a0 /* SODIMM 31 */
-			MX6UL_PAD_LCD_DATA18__GPIO3_IO23	0x10b0 /* SODIMM 29 */
-			MX6UL_PAD_JTAG_TDO__GPIO1_IO12		0x90b1 /* SODIMM 23 */
-			MX6UL_PAD_LCD_DATA19__GPIO3_IO24        0x10b0 /* SODIMM 37 */
+			MX6UL_PAD_JTAG_TDI__GPIO1_IO13		0x70a0 /* SODIMM 31 / DCD */
+			MX6UL_PAD_LCD_DATA18__GPIO3_IO23	0x10b0 /* SODIMM 29 / DSR */
+			MX6UL_PAD_JTAG_TDO__GPIO1_IO12		0x90b1 /* SODIMM 23 / DTR */
+			MX6UL_PAD_LCD_DATA19__GPIO3_IO24        0x10b0 /* SODIMM 37 / RI */
 		>;
 	};
 
-	pinctrl_uart2: uart2-grp {
+	pinctrl_uart2: uart2grp {
 		fsl,pins = <
 			MX6UL_PAD_UART2_TX_DATA__UART2_DTE_RX	0x1b0b1 /* SODIMM 36 */
 			MX6UL_PAD_UART2_RX_DATA__UART2_DTE_TX	0x1b0b1 /* SODIMM 38 */
@@ -487,23 +600,23 @@
 			MX6UL_PAD_UART2_RTS_B__UART2_DTE_CTS	0x1b0b1 /* SODIMM 34 */
 		>;
 	};
-	pinctrl_uart5: uart5-grp {
+	pinctrl_uart5: uart5grp {
 		fsl,pins = <
 			MX6UL_PAD_GPIO1_IO04__UART5_DTE_RX	0x1b0b1 /* SODIMM 19 */
 			MX6UL_PAD_GPIO1_IO05__UART5_DTE_TX	0x1b0b1 /* SODIMM 21 */
 		>;
 	};
 
-	pinctrl_usbh_reg: gpio-usbh-reg {
+	pinctrl_usbh_reg: usbhreggrp {
 		fsl,pins = <
-			MX6UL_PAD_GPIO1_IO02__GPIO1_IO02	0x10b0 /* SODIMM 129 */
+			MX6UL_PAD_GPIO1_IO02__GPIO1_IO02	0x10b0 /* SODIMM 129 / USBH_PEN */
 		>;
 	};
 
-	pinctrl_usdhc1: usdhc1-grp {
+	pinctrl_usdhc1: usdhc1grp {
 		fsl,pins = <
-			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x17059 /* SODIMM 47 */
-			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x10059 /* SODIMM 190 */
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x10059 /* SODIMM 47 */
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x17059 /* SODIMM 190 */
 			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x17059 /* SODIMM 192 */
 			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x17059 /* SODIMM 49 */
 			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x17059 /* SODIMM 51 */
@@ -511,10 +624,10 @@
 		>;
 	};
 
-	pinctrl_usdhc1_100mhz: usdhc1-100mhz-grp {
+	pinctrl_usdhc1_100mhz: usdhc1-100mhzgrp {
 		fsl,pins = <
-			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x170b9
-			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x100b9
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x100b9
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x170b9
 			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x170b9
 			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x170b9
 			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x170b9
@@ -522,25 +635,25 @@
 		>;
 	};
 
-	pinctrl_usdhc1_200mhz: usdhc1-200mhz-grp {
+	pinctrl_usdhc1_200mhz: usdhc1-200mhzgrp {
 		fsl,pins = <
-			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x170f9
-			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x100f9
-			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x170b9
-			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x170b9
-			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x170b9
-			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x170b9
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x100f9
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x170f9
+			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x170f9
+			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x170f9
+			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x170f9
+			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x170f9
 		>;
 	};
 
-	pinctrl_usdhc2: usdhc2-grp {
+	pinctrl_usdhc2: usdhc2grp {
 		fsl,pins = <
 			MX6UL_PAD_CSI_DATA00__USDHC2_DATA0	0x17069
 			MX6UL_PAD_CSI_DATA01__USDHC2_DATA1	0x17069
 			MX6UL_PAD_CSI_DATA02__USDHC2_DATA2	0x17069
 			MX6UL_PAD_CSI_DATA03__USDHC2_DATA3	0x17069
 			MX6UL_PAD_CSI_HSYNC__USDHC2_CMD		0x17069
-			MX6UL_PAD_CSI_VSYNC__USDHC2_CLK		0x17069
+			MX6UL_PAD_CSI_VSYNC__USDHC2_CLK		0x10069
 
 			MX6UL_PAD_GPIO1_IO03__OSC32K_32K_OUT	0x10
 		>;
@@ -561,7 +674,7 @@
 		>;
 	};
 
-	pinctrl_wdog: wdog-grp {
+	pinctrl_wdog: wdoggrp {
 		fsl,pins = <
 			MX6UL_PAD_LCD_RESET__WDOG1_WDOG_ANY    0x30b0
 		>;
@@ -569,65 +682,65 @@
 };
 
 &iomuxc_snvs {
-	pinctrl_snvs_gpio1: snvs-gpio1-grp {
+	pinctrl_atmel_snvs_conn: atmelsnvsconngrp {
 		fsl,pins = <
-			MX6ULL_PAD_SNVS_TAMPER6__GPIO5_IO06	0x110a0	/* SODIMM 93 */
-			MX6ULL_PAD_SNVS_TAMPER3__GPIO5_IO03	0x110a0	/* SODIMM 95 */
-			MX6ULL_PAD_BOOT_MODE0__GPIO5_IO10	0x1b0a0	/* SODIMM 105 */
-			MX6ULL_PAD_SNVS_TAMPER5__GPIO5_IO05	0x0b0a0	/* SODIMM 131 */
-			MX6ULL_PAD_SNVS_TAMPER8__GPIO5_IO08	0x110a0	/* SODIMM 138 */
+			MX6ULL_PAD_SNVS_TAMPER4__GPIO5_IO04     0xb0a0	/* SODIMM 107 */
 		>;
 	};
 
-	pinctrl_snvs_gpio2: snvs-gpio2-grp { /* ATMEL MXT TOUCH */
+	pinctrl_snvs_gpio1: snvsgpio1grp {
 		fsl,pins = <
-			MX6ULL_PAD_SNVS_TAMPER4__GPIO5_IO04	0xb0a0	/* SODIMM 107 */
+			MX6ULL_PAD_SNVS_TAMPER6__GPIO5_IO06	0x110a0	/* SODIMM 93 */
+			MX6ULL_PAD_SNVS_TAMPER3__GPIO5_IO03	0x110a0	/* SODIMM 95 */
+			MX6ULL_PAD_BOOT_MODE0__GPIO5_IO10	0x1b0a0	/* SODIMM 105 */
+			MX6ULL_PAD_SNVS_TAMPER5__GPIO5_IO05	0x0b0a0	/* SODIMM 131 / USBH_OC */
+			MX6ULL_PAD_SNVS_TAMPER8__GPIO5_IO08	0x110a0	/* SODIMM 138 */
 		>;
 	};
 
-	pinctrl_snvs_gpio3: snvs-gpio3-grp { /* Wifi pins */
+	pinctrl_snvs_gpio3: snvsgpio3grp { /* Wifi pins */
 		fsl,pins = <
 			MX6ULL_PAD_BOOT_MODE1__GPIO5_IO11	0x130a0	/* SODIMM 127 */
 		>;
 	};
 
-	pinctrl_snvs_ad7879_int: snvs-ad7879-int-grp { /* TOUCH Interrupt */
+	pinctrl_snvs_ad7879_int: snvsad7879intgrp { /* TOUCH Interrupt */
 		fsl,pins = <
 			MX6ULL_PAD_SNVS_TAMPER7__GPIO5_IO07	0x100b0
 		>;
 	};
 
-	pinctrl_snvs_reg_sd: snvs-reg-sd-grp {
+	pinctrl_snvs_reg_sd: snvsregsdgrp {
 		fsl,pins = <
 			MX6ULL_PAD_SNVS_TAMPER9__GPIO5_IO09	0x400100b0
 		>;
 	};
 
-	pinctrl_snvs_usbc_det: snvs-usbc-det-grp {
+	pinctrl_snvs_usbc_det: snvsusbcdetgrp {
 		fsl,pins = <
 			MX6ULL_PAD_SNVS_TAMPER2__GPIO5_IO02	0x130b0
 		>;
 	};
 
-	pinctrl_snvs_gpiokeys: snvs-gpiokeys-grp {
+	pinctrl_snvs_gpiokeys: snvsgpiokeysgrp {
 		fsl,pins = <
-			MX6ULL_PAD_SNVS_TAMPER1__GPIO5_IO01	0x130a0	/* SODIMM 45 */
+			MX6ULL_PAD_SNVS_TAMPER1__GPIO5_IO01	0x130a0	/* SODIMM 45 / WAKE_UP */
 		>;
 	};
 
-	pinctrl_snvs_usdhc1_cd: snvs-usdhc1-cd-grp {
+	pinctrl_snvs_usdhc1_cd: snvsusdhc1cdgrp {
 		fsl,pins = <
-			MX6ULL_PAD_SNVS_TAMPER0__GPIO5_IO00	0x1b0a0 /* SODIMM 43 */
+			MX6ULL_PAD_SNVS_TAMPER0__GPIO5_IO00	0x1b0a0 /* SODIMM 43 / MMC_CD */
 		>;
 	};
 
-	pinctrl_snvs_usdhc1_sleep_cd: snvs-usdhc1-cd-grp-slp {
+	pinctrl_snvs_usdhc1_cd_sleep: snvsusdhc1cd-sleepgrp {
 		fsl,pins = <
 			MX6ULL_PAD_SNVS_TAMPER0__GPIO5_IO00	0x0
 		>;
 	};
 
-	pinctrl_snvs_wifi_pdn: snvs-wifi-pdn-grp {
+	pinctrl_snvs_wifi_pdn: snvswifipdngrp {
 		fsl,pins = <
 			MX6ULL_PAD_BOOT_MODE1__GPIO5_IO11	0x130a0
 		>;
diff --git a/arch/arm/boot/dts/imx6ull-jozacp.dts b/arch/arm/boot/dts/imx6ull-jozacp.dts
new file mode 100644
index 000000000000..a152eeb78e88
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ull-jozacp.dts
@@ -0,0 +1,456 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2020 Protonic Holland
+ * Copyright (c) 2020 Oleksij Rempel <kernel@pengutronix.de>, Pengutronix
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include "imx6ull.dtsi"
+
+/ {
+	model = "JOZ Access Point";
+	compatible = "joz,jozacp", "fsl,imx6ull";
+
+	chosen {
+		stdout-path = &uart1;
+	};
+
+	/* On board name LED_RGB1 */
+	led-controller-1 {
+		compatible = "pwm-leds";
+
+		led-0 {
+			color = <LED_COLOR_ID_RED>;
+			function = LED_FUNCTION_INDICATOR;
+			function-enumerator = <0>;
+			pwms = <&pwm1 0 10000000 0>;
+			max-brightness = <255>;
+		};
+
+		led-1 {
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_INDICATOR;
+			function-enumerator = <1>;
+			pwms = <&pwm3 0 10000000 0>;
+			max-brightness = <255>;
+		};
+
+		led-2 {
+			color = <LED_COLOR_ID_BLUE>;
+			function = LED_FUNCTION_INDICATOR;
+			function-enumerator = <2>;
+			pwms = <&pwm5 0 10000000 0>;
+			max-brightness = <255>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	/* On board name LED_RGB2 */
+	led-controller-2 {
+		compatible = "pwm-leds";
+
+		led-3 {
+			color = <LED_COLOR_ID_RED>;
+			function = LED_FUNCTION_INDICATOR;
+			function-enumerator = <3>;
+			pwms = <&pwm2 0 10000000 0>;
+			max-brightness = <255>;
+		};
+
+		led-4 {
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_INDICATOR;
+			function-enumerator = <4>;
+			pwms = <&pwm4 0 10000000 0>;
+			max-brightness = <255>;
+		};
+
+		led-5 {
+			color = <LED_COLOR_ID_BLUE>;
+			function = LED_FUNCTION_INDICATOR;
+			function-enumerator = <5>;
+			pwms = <&pwm6 0 10000000 0>;
+			max-brightness = <255>;
+		};
+	};
+
+	reg_3v3: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&reg_5v0>;
+	};
+
+	reg_5v0: regulator-5v0 {
+		compatible = "regulator-fixed";
+		regulator-name = "5v0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	reg_vbus: regulator-vbus {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_vbus>;
+		regulator-name = "vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&reg_5v0>;
+		gpio = <&gpio1 2 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	usdhc2_wifi_pwrseq: usdhc2-wifi-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_wifi_npd>;
+		reset-gpios = <&gpio4 25 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&can1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_can1>;
+	status = "okay";
+};
+
+&cpu0 {
+	clock-frequency = <792000000>;
+};
+
+&fec1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet1>;
+	phy-mode = "rmii";
+	phy-handle = <&ethphy0>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy0: ethernet-phy@0 {
+			reg = <0>;
+			clocks = <&clks IMX6UL_CLK_ENET_REF>;
+			clock-names = "rmii-ref";
+			interrupts-extended = <&gpio1 29 IRQ_TYPE_LEVEL_LOW>;
+			reset-gpios = <&gpio1 28 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <10000>;
+			reset-deassert-us = <300>;
+		};
+	};
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	clock-frequency = <100000>;
+	status = "okay";
+};
+
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	clock-frequency = <100000>;
+	status = "okay";
+
+	rtc@51 {
+		compatible = "nxp,pcf8563";
+		reg = <0x51>;
+	};
+};
+
+&pwm1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm1>;
+	status = "okay";
+};
+
+&pwm2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm2>;
+	status = "okay";
+};
+
+&pwm3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm3>;
+	status = "okay";
+};
+
+&pwm4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm4>;
+	status = "okay";
+};
+
+&pwm5 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm5>;
+	status = "okay";
+};
+
+&pwm6 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm6>;
+	status = "okay";
+};
+
+&snvs_rtc {
+	status = "disabled";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+	dtr-gpios = <&gpio3 4 GPIO_ACTIVE_LOW>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&usbotg1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg1>;
+	vbus-supply = <&reg_vbus>;
+	dr_mode = "host";
+	over-current-active-low;
+	status = "okay";
+};
+
+&usdhc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	vmmc-supply = <&reg_3v3>;
+	bus-width = <8>;
+	no-1-8-v;
+	non-removable;
+	cap-mmc-hw-reset;
+	no-sd;
+	no-sdio;
+	status = "okay";
+};
+
+&usdhc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	mmc-pwrseq = <&usdhc2_wifi_pwrseq>;
+	bus-width = <4>;
+	no-1-8-v;
+	no-mmc;
+	no-sd;
+	non-removable;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	wifi@1 {
+		compatible = "brcm,bcm4329-fmac";
+		reg = <1>;
+	};
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hog>;
+
+	pinctrl_can1: can1grp {
+		fsl,pins = <
+			MX6UL_PAD_UART3_CTS_B__FLEXCAN1_TX	0x1b0b0
+			MX6UL_PAD_UART3_RTS_B__FLEXCAN1_RX	0x1b0b0
+		>;
+	};
+
+	pinctrl_enet1: enet1grp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO07__ENET1_MDC	 0x1b0b0
+			MX6UL_PAD_GPIO1_IO06__ENET1_MDIO	0x1b0b0
+			MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN	0x1b0b0
+			MX6UL_PAD_ENET1_RX_ER__ENET1_RX_ER	0x1b0b0
+			MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00	0x1b0b0
+			MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01	0x1b0b0
+			MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN	0x1b0b0
+			MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00	0x1b0b0
+			MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01	0x1b0b0
+			MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1	0x4001b031
+
+			MX6UL_PAD_UART4_TX_DATA__GPIO1_IO28	0x038b0
+			MX6UL_PAD_UART4_RX_DATA__GPIO1_IO29	0x170b0
+		>;
+	};
+
+	pinctrl_hog: hoggrp {
+		fsl,pins = <
+			/* HW Revision */
+			MX6UL_PAD_ENET2_RX_DATA0__GPIO2_IO08	0x1b0b0
+			MX6UL_PAD_ENET2_RX_DATA1__GPIO2_IO09	0x1b0b0
+			MX6UL_PAD_ENET2_RX_EN__GPIO2_IO10	0x1b0b0
+
+			/* HW ID */
+			MX6UL_PAD_ENET2_TX_DATA0__GPIO2_IO11	0x1b0b0
+			MX6UL_PAD_ENET2_TX_DATA1__GPIO2_IO12	0x1b0b0
+			MX6UL_PAD_ENET2_TX_EN__GPIO2_IO13	0x1b0b0
+			MX6UL_PAD_ENET2_TX_CLK__GPIO2_IO14	0x1b0b0
+			MX6UL_PAD_ENET2_RX_ER__GPIO2_IO15	0x1b0b0
+
+			/* Digital inputs */
+			MX6UL_PAD_GPIO1_IO03__GPIO1_IO03	0x11000
+			MX6UL_PAD_GPIO1_IO04__GPIO1_IO04	0x11000
+			MX6UL_PAD_GPIO1_IO05__GPIO1_IO05	0x11000
+			MX6UL_PAD_GPIO1_IO08__GPIO1_IO08	0x11000
+			MX6UL_PAD_GPIO1_IO09__GPIO1_IO09	0x11000
+
+			/* Isolated outputs */
+			MX6UL_PAD_UART2_TX_DATA__GPIO1_IO20	0x01020
+			MX6UL_PAD_UART2_RX_DATA__GPIO1_IO21	0x01020
+			MX6UL_PAD_UART2_RTS_B__GPIO1_IO23	0x01020
+			MX6UL_PAD_UART3_TX_DATA__GPIO1_IO24	0x01020
+			MX6UL_PAD_UART3_RX_DATA__GPIO1_IO25	0x01020
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX6UL_PAD_CSI_MCLK__I2C1_SDA		0x4001f8b1
+			MX6UL_PAD_CSI_PIXCLK__I2C1_SCL		0x4001f8b1
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX6UL_PAD_UART5_RX_DATA__I2C2_SDA	0x4001f8b1
+			MX6UL_PAD_UART5_TX_DATA__I2C2_SCL	0x4001f8b1
+		>;
+	};
+
+	pinctrl_pwm1: pwm1grp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA00__PWM1_OUT		0x01010
+		>;
+	};
+
+	pinctrl_pwm2: pwm2grp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA01__PWM2_OUT		0x01010
+		>;
+	};
+
+	pinctrl_pwm3: pwm3grp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA02__PWM3_OUT		0x01010
+		>;
+	};
+
+	pinctrl_pwm4: pwm4grp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA03__PWM4_OUT		0x01010
+		>;
+	};
+
+	pinctrl_pwm5: pwm5grp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA18__PWM5_OUT		0x01010
+		>;
+	};
+
+	pinctrl_pwm6: pwm6grp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA19__PWM6_OUT		0x01010
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX	0x1b0b1
+			MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart4: uart4grp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_CLK__UART4_DCE_TX		0x1b0b0
+			MX6UL_PAD_LCD_ENABLE__UART4_DCE_RX	0x1b0b0
+			MX6UL_PAD_LCD_HSYNC__UART4_DCE_CTS	0x1b0b0
+			MX6UL_PAD_LCD_VSYNC__UART4_DCE_RTS	0x1b0b0
+			MX6UL_PAD_LCD_RESET__GPIO3_IO04		0x1b0b0
+		>;
+	};
+
+	pinctrl_usbotg1: usbotg1grp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO01__USB_OTG1_OC	0x1b0b0
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_WP_B__USDHC1_RESET_B	0x17099
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x1f099
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x10099
+			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x17099
+			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x17099
+			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x17099
+			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x17099
+			MX6UL_PAD_NAND_READY_B__USDHC1_DATA4	0x17099
+			MX6UL_PAD_NAND_CE0_B__USDHC1_DATA5	0x17099
+			MX6UL_PAD_NAND_CE1_B__USDHC1_DATA6	0x17099
+			MX6UL_PAD_NAND_CLE__USDHC1_DATA7	0x17099
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX6UL_PAD_CSI_VSYNC__USDHC2_CLK		0x100b9
+			MX6UL_PAD_CSI_HSYNC__USDHC2_CMD		0x170b9
+			MX6UL_PAD_CSI_DATA00__USDHC2_DATA0	0x170b9
+			MX6UL_PAD_CSI_DATA01__USDHC2_DATA1	0x170b9
+			MX6UL_PAD_CSI_DATA02__USDHC2_DATA2	0x170b9
+			MX6UL_PAD_CSI_DATA03__USDHC2_DATA3	0x170b9
+		>;
+	};
+
+	pinctrl_vbus: vbus0grp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO02__GPIO1_IO02	0x030b0
+		>;
+	};
+
+	pinctrl_wifi_npd: wifigrp {
+		fsl,pins = <
+			/* WL_REG_ON */
+			MX6UL_PAD_CSI_DATA04__GPIO4_IO25	0x03020
+		>;
+	};
+};
+
+&iomuxc_snvs {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_snvs_hog>;
+
+	pinctrl_snvs_hog: snvs-hog-grp {
+		fsl,pins = <
+			/* Digital outputs */
+			MX6ULL_PAD_SNVS_TAMPER2__GPIO5_IO02	0x00020
+			MX6ULL_PAD_SNVS_TAMPER3__GPIO5_IO03	0x00020
+			MX6ULL_PAD_SNVS_TAMPER4__GPIO5_IO04	0x00020
+			MX6ULL_PAD_SNVS_TAMPER5__GPIO5_IO05	0x00020
+			MX6ULL_PAD_SNVS_TAMPER6__GPIO5_IO06	0x00020
+
+			/* Digital outputs fault feedback */
+			MX6ULL_PAD_SNVS_TAMPER0__GPIO5_IO00	0x17000
+			MX6ULL_PAD_SNVS_TAMPER1__GPIO5_IO01	0x17000
+			MX6ULL_PAD_SNVS_TAMPER7__GPIO5_IO07	0x17000
+			MX6ULL_PAD_SNVS_TAMPER8__GPIO5_IO08	0x17000
+			MX6ULL_PAD_SNVS_TAMPER9__GPIO5_IO09	0x17000
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6ull-kontron-bl.dts b/arch/arm/boot/dts/imx6ull-kontron-bl.dts
new file mode 100644
index 000000000000..fa016465cdbc
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ull-kontron-bl.dts
@@ -0,0 +1,15 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2017 exceet electronics GmbH
+ * Copyright (C) 2019 Kontron Electronics GmbH
+ */
+
+/dts-v1/;
+
+#include "imx6ull-kontron-sl.dtsi"
+#include "imx6ul-kontron-bl-common.dtsi"
+
+/ {
+	model = "Kontron BL i.MX6ULL (N641X S)";
+	compatible = "kontron,bl-imx6ull", "kontron,sl-imx6ull", "fsl,imx6ull";
+};
diff --git a/arch/arm/boot/dts/imx6ull-kontron-n6411-s.dts b/arch/arm/boot/dts/imx6ull-kontron-n6411-s.dts
deleted file mode 100644
index 57588a5e1e34..000000000000
--- a/arch/arm/boot/dts/imx6ull-kontron-n6411-s.dts
+++ /dev/null
@@ -1,16 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Copyright (C) 2017 exceet electronics GmbH
- * Copyright (C) 2019 Kontron Electronics GmbH
- */
-
-/dts-v1/;
-
-#include "imx6ull-kontron-n6411-som.dtsi"
-#include "imx6ul-kontron-n6x1x-s.dtsi"
-
-/ {
-	model = "Kontron N6411 S";
-	compatible = "kontron,imx6ull-n6411-s", "kontron,imx6ull-n6411-som",
-		     "fsl,imx6ull";
-};
diff --git a/arch/arm/boot/dts/imx6ull-kontron-n6411-som.dtsi b/arch/arm/boot/dts/imx6ull-kontron-n6411-som.dtsi
deleted file mode 100644
index b7e984284e1a..000000000000
--- a/arch/arm/boot/dts/imx6ull-kontron-n6411-som.dtsi
+++ /dev/null
@@ -1,40 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Copyright (C) 2017 exceet electronics GmbH
- * Copyright (C) 2018 Kontron Electronics GmbH
- */
-
-#include "imx6ull.dtsi"
-#include "imx6ul-kontron-n6x1x-som-common.dtsi"
-
-/ {
-	model = "Kontron N6411 SOM";
-	compatible = "kontron,imx6ull-n6311-som", "fsl,imx6ull";
-
-	memory@80000000 {
-		reg = <0x80000000 0x20000000>;
-		device_type = "memory";
-	};
-};
-
-&qspi {
-	spi-flash@0 {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		compatible = "spi-nand";
-		spi-max-frequency = <104000000>;
-		spi-tx-bus-width = <4>;
-		spi-rx-bus-width = <4>;
-		reg = <0>;
-
-		partition@0 {
-			label = "ubi1";
-			reg = <0x00000000 0x08000000>;
-		};
-
-		partition@8000000 {
-			label = "ubi2";
-			reg = <0x08000000 0x18000000>;
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/imx6ull-kontron-sl.dtsi b/arch/arm/boot/dts/imx6ull-kontron-sl.dtsi
new file mode 100644
index 000000000000..93f10eb3494f
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ull-kontron-sl.dtsi
@@ -0,0 +1,13 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2017 exceet electronics GmbH
+ * Copyright (C) 2018 Kontron Electronics GmbH
+ */
+
+#include "imx6ull.dtsi"
+#include "imx6ul-kontron-sl-common.dtsi"
+
+/ {
+	model = "Kontron SL i.MX6ULL (N641X SOM)";
+	compatible = "kontron,sl-imx6ull", "fsl,imx6ull";
+};
diff --git a/arch/arm/boot/dts/imx6ull-phytec-segin-ff-rdk-nand.dts b/arch/arm/boot/dts/imx6ull-phytec-segin-ff-rdk-nand.dts
index c8d3eff9ed4b..1d7362b5ac91 100644
--- a/arch/arm/boot/dts/imx6ull-phytec-segin-ff-rdk-nand.dts
+++ b/arch/arm/boot/dts/imx6ull-phytec-segin-ff-rdk-nand.dts
@@ -10,6 +10,7 @@
 #include "imx6ull-phytec-segin.dtsi"
 #include "imx6ull-phytec-segin-peb-eval-01.dtsi"
 #include "imx6ull-phytec-segin-peb-av-02.dtsi"
+#include "imx6ull-phytec-segin-peb-wlbt-05.dtsi"
 
 / {
 	model = "PHYTEC phyBOARD-Segin i.MX6 ULL Full Featured with NAND";
diff --git a/arch/arm/boot/dts/imx6ull-phytec-segin-lc-rdk-nand.dts b/arch/arm/boot/dts/imx6ull-phytec-segin-lc-rdk-nand.dts
index e168494e0a6d..4bcbae024d8d 100644
--- a/arch/arm/boot/dts/imx6ull-phytec-segin-lc-rdk-nand.dts
+++ b/arch/arm/boot/dts/imx6ull-phytec-segin-lc-rdk-nand.dts
@@ -9,6 +9,7 @@
 #include "imx6ull-phytec-phycore-som.dtsi"
 #include "imx6ull-phytec-segin.dtsi"
 #include "imx6ull-phytec-segin-peb-eval-01.dtsi"
+#include "imx6ull-phytec-segin-peb-wlbt-05.dtsi"
 
 / {
 	model = "PHYTEC phyBOARD-Segin i.MX6 ULL Low Cost with NAND";
diff --git a/arch/arm/boot/dts/imx6ull-phytec-segin-peb-wlbt-05.dtsi b/arch/arm/boot/dts/imx6ull-phytec-segin-peb-wlbt-05.dtsi
new file mode 100644
index 000000000000..df25814a3371
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ull-phytec-segin-peb-wlbt-05.dtsi
@@ -0,0 +1,19 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2021 PHYTEC Messtechnik GmbH
+ * Author: Yunus Bas <y.bas@phytec.de>
+ */
+
+#include "imx6ul-phytec-segin-peb-wlbt-05.dtsi"
+
+&iomuxc {
+	/delete-node/ wlgrp;
+};
+
+&iomuxc_snvs {
+	pinctrl_wl: wlgrp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER9__GPIO5_IO09	0x3031
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6ull-phytec-tauri-emmc.dts b/arch/arm/boot/dts/imx6ull-phytec-tauri-emmc.dts
new file mode 100644
index 000000000000..14adb87da911
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ull-phytec-tauri-emmc.dts
@@ -0,0 +1,20 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2021 PHYTEC Messtechnik GmbH
+ * Author: Alexander Bauer <a.bauer@phytec.de>
+ */
+
+/dts-v1/;
+#include "imx6ull-phytec-tauri.dtsi"
+
+/ {
+	model = "PHYTEC phyGate-Tauri i.MX6 UltraLite";
+	compatible = "phytec,imx6ull-phygate-tauri",
+		     "phytec,imx6ull-phygate-tauri-emmc",
+		     "phytec,imx6ull-pcl063", "fsl,imx6ull";
+};
+
+/* EMMC-Version */
+&usdhc2 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6ull-phytec-tauri-nand.dts b/arch/arm/boot/dts/imx6ull-phytec-tauri-nand.dts
new file mode 100644
index 000000000000..ae396ac63443
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ull-phytec-tauri-nand.dts
@@ -0,0 +1,20 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2021 PHYTEC Messtechnik GmbH
+ * Author: Alexander Bauer <a.bauer@phytec.de>
+ */
+
+/dts-v1/;
+#include "imx6ull-phytec-tauri.dtsi"
+
+/ {
+	model = "PHYTEC phyGate-Tauri i.MX6 UltraLite";
+	compatible = "phytec,imx6ull-phygate-tauri",
+		     "phytec,imx6ull-phygate-tauri-nand",
+		     "phytec,imx6ull-pcl063", "fsl,imx6ull";
+};
+
+/* NAND-Version */
+&gpmi {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx6ull-phytec-tauri.dtsi b/arch/arm/boot/dts/imx6ull-phytec-tauri.dtsi
new file mode 100644
index 000000000000..5464a52a1f94
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ull-phytec-tauri.dtsi
@@ -0,0 +1,588 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2021 PHYTEC Messtechnik GmbH
+ * Author: Alexander Bauer <a.bauer@phytec.de>
+ */
+
+/dts-v1/;
+#include "imx6ull.dtsi"
+#include "imx6ull-phytec-phycore-som.dtsi"
+
+/ {
+
+	model = "PHYTEC phyGate-Tauri i.MX6 UltraLite";
+	compatible = "phytec,imx6ull-phygate-tauri",
+		     "phytec,imx6ull-pcl063", "fsl,imx6ull";
+
+	aliases {
+		rtc0 = &i2c_rtc;
+		rtc1 = &snvs_rtc;
+	};
+
+	gpio_keys: gpio-keys {
+		compatible = "gpio-key";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_keys>;
+
+		key {
+			label = "KEY-A";
+			gpios = <&gpio1 18 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_A>;
+			wakeup-source;
+		};
+	};
+
+	reg_adc1_vref_3v3: regulator-vref-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "vref-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	reg_s25fl064_hold: regulator-s25fl064-hold {
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_s25fl064_hold>;
+		compatible = "regulator-fixed";
+		regulator-name = "s25fl064_hold";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio3 17 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-always-on;
+	};
+
+	reg_usb_hub_vbus: regulator-hub-otg1-vbus {
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usbhubpwr>;
+		compatible = "regulator-fixed";
+		regulator-name = "usb_hub_vbus";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio5 5 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-always-on;
+	};
+
+	reg_usb_otg1_vbus: regulator-usb-otg1-vbus {
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usbotg1pwr>;
+		compatible = "regulator-fixed";
+		regulator-name = "usb_otg1_vbus";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio4 28 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-always-on;
+	};
+
+	user_leds: user-leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_user_leds>,
+			    <&pinctrl_user_leds_snvs>;
+
+		user-led1 {
+			label = "yellow";
+			gpios = <&gpio1 3 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "off";
+		};
+
+		user-led2 {
+			label = "red";
+			gpios = <&gpio5 9 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "off";
+		};
+	};
+};
+
+&can1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan1>;
+	status = "okay";
+};
+
+&can2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan2>;
+	status = "okay";
+};
+
+&ecspi1 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1>,
+		    <&pinctrl_ecspi1_cs>;
+	cs-gpios = <&gpio3 26 GPIO_ACTIVE_LOW>,
+		   <&gpio3 10 GPIO_ACTIVE_LOW>,
+		   <&gpio3 11 GPIO_ACTIVE_LOW>;
+	status = "okay";
+
+	tpm_tis: tpm@1 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_tpm>;
+		compatible = "tcg,tpm_tis-spi";
+		reg = <1>;
+		spi-max-frequency = <20000000>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
+	};
+
+	s25fl064: flash@2 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = " jedec,spi-nor";
+		reg = <2>;
+		spi-max-frequency = <40000000>;
+		m25p,fast-read;
+		status = "disabled";
+	};
+};
+
+&ecspi3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi3>;
+	cs-gpios = <&gpio1 20 GPIO_ACTIVE_LOW>;
+	dmas = <&sdma 7 8 0>,
+	       <&sdma 8 8 0>;
+	dma-names = "rx", "tx";
+	status = "okay";
+};
+
+&ethphy1 {
+	status = "okay";
+};
+
+&fec1 {
+	status = "okay";
+};
+
+&fec2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet2>;
+	phy-mode = "rmii";
+	phy-handle = <&ethphy2>;
+	status = "okay";
+};
+
+&i2c1 {
+	status = "okay";
+
+	tmp102: tmp@49 {
+		compatible = "ti,tmp102";
+		reg = <0x49>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_tempsense>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+		#thermal-sensor-cells = <1>;
+	};
+
+	i2c_rtc: rtc@68 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_rtc_int>;
+		compatible = "microcrystal,rv4162";
+		reg = <0x68>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
+&i2c2 {
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	pinctrl-1 = <&pinctrl_i2c2_gpio>;
+	sda-gpios = <&gpio1 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	scl-gpios = <&gpio1 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "okay";
+};
+
+&i2c3 {
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	pinctrl-1 = <&pinctrl_i2c3_gpio>;
+	sda-gpios = <&gpio3 5 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	scl-gpios = <&gpio3 6 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "okay";
+};
+
+&i2c4 {
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c4>;
+	pinctrl-1 = <&pinctrl_i2c4_gpio>;
+	sda-gpios = <&gpio3 7 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	scl-gpios = <&gpio3 8 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "okay";
+};
+
+&mdio {
+	ethphy2: ethernet-phy@2 {
+		reg = <2>;
+		micrel,led-mode = <1>;
+		clocks = <&clks IMX6UL_CLK_ENET2_REF>;
+		clock-names = "rmii-ref";
+		status = "okay";
+	};
+};
+
+&pwm3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm3>;
+	status = "okay";
+};
+
+&pwm6 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm6>;
+	status = "okay";
+};
+
+&pwm7 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm7>;
+	status = "okay";
+};
+
+&pwm8 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm8>;
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	status = "okay";
+};
+
+/* UART4 * RS485  */
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+	rts-gpios = <&gpio3 2 GPIO_ACTIVE_HIGH>;
+	rs485-rts-active-high;
+	linux,rs485-enabled-at-boot-time;
+	status = "okay";
+};
+
+/* UART5 * RS232  */
+&uart5 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart5>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&uart7 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart7>;
+	status = "okay";
+};
+
+/* USB */
+&usbotg1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb_otg1>;
+	vbus-supply = <&reg_usb_otg1_vbus>;
+	dr_mode = "host";
+	disable-over-current;
+	status = "okay";
+};
+
+&usbotg2 {
+	vbus-supply = <&reg_usb_hub_vbus>;
+	disable-over-current;
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usdhc1 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
+	cd-gpios = <&gpio1 19 GPIO_ACTIVE_LOW>;
+	no-1-8-v;
+	keep-power-in-suspend;
+	wakeup-source;
+	status = "okay";
+};
+
+&usdhc2 {
+	status = "disabled";
+};
+
+&iomuxc_snvs {
+	pinctrl_rtc_int: rtcintgrp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER1__GPIO5_IO01	0x17059
+		>;
+	};
+
+	pinctrl_stmpe: stmpegrp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER3__GPIO5_IO03	0x17059
+		>;
+	};
+
+	pinctrl_tempsense: tempsensegrp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER0__GPIO5_IO00	0x17059
+		>;
+	};
+
+	pinctrl_tpm: tpmgrp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER2__GPIO5_IO02	0x17059
+		>;
+	};
+
+	pinctrl_usbhubpwr: usbhubpwrgrp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER5__GPIO5_IO05	0x17059
+		>;
+	};
+
+	pinctrl_user_leds_snvs: user_ledsgrp {
+		fsl,pins = <
+			MX6ULL_PAD_SNVS_TAMPER9__GPIO5_IO09	0x79
+		>;
+	};
+};
+
+&iomuxc {
+	pinctrl_gpio: gpiogrp {
+		fsl,pins = <
+			MX6UL_PAD_CSI_DATA05__GPIO4_IO26	0x17059  /* nUART_MUX_RS232 */
+			MX6UL_PAD_CSI_DATA04__GPIO4_IO25	0x17059  /* nUART_MUX_DUAL_RX_TX */
+		>;
+	};
+
+	pinctrl_gpio_keys: gpiokeysgrp {
+		fsl,pins = <
+			MX6UL_PAD_UART1_CTS_B__GPIO1_IO18	0x79
+		>;
+	};
+
+	pinctrl_ecspi3: ecspi3grp {
+		fsl,pins = <
+			MX6UL_PAD_UART2_RX_DATA__ECSPI3_SCLK	0x100b1
+			MX6UL_PAD_UART2_RTS_B__ECSPI3_MISO	0x100b1
+			MX6UL_PAD_UART2_CTS_B__ECSPI3_MOSI	0x100b1
+			MX6UL_PAD_UART2_TX_DATA__GPIO1_IO20	0x10b0
+		>;
+	};
+
+	pinctrl_ecspi1: ecspi1grp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA20__ECSPI1_SCLK	0x100b1
+			MX6UL_PAD_LCD_DATA23__ECSPI1_MISO	0x100b1
+			MX6UL_PAD_LCD_DATA22__ECSPI1_MOSI	0x100b1
+		>;
+	};
+
+	pinctrl_ecspi1_cs: ecspi1csgrp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA21__GPIO3_IO26	0x10b0
+			MX6UL_PAD_LCD_DATA05__GPIO3_IO10	0x10b0
+			MX6UL_PAD_LCD_DATA06__GPIO3_IO11	0x10b0
+		>;
+	};
+
+
+	pinctrl_enet2: enet2grp {
+		fsl,pins = <
+			MX6UL_PAD_ENET2_RX_EN__ENET2_RX_EN	0x1b0b0
+			MX6UL_PAD_ENET2_RX_ER__ENET2_RX_ER	0x1b0b0
+			MX6UL_PAD_ENET2_RX_DATA0__ENET2_RDATA00	0x1b0b0
+			MX6UL_PAD_ENET2_RX_DATA1__ENET2_RDATA01	0x1b0b0
+			MX6UL_PAD_ENET2_TX_EN__ENET2_TX_EN	0x1b010
+			MX6UL_PAD_ENET2_TX_DATA0__ENET2_TDATA00	0x1b010
+			MX6UL_PAD_ENET2_TX_DATA1__ENET2_TDATA01	0x1b010
+			MX6UL_PAD_ENET2_TX_CLK__ENET2_REF_CLK2	0x4001b010
+		>;
+	};
+
+	pinctrl_flexcan1: flexcan1grp {
+		fsl,pins = <
+			MX6UL_PAD_UART3_CTS_B__FLEXCAN1_TX	0x0b0b0
+			MX6UL_PAD_UART3_RTS_B__FLEXCAN1_RX	0x0b0b0
+		>;
+	};
+
+	pinctrl_flexcan2: flexcan2grp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA10__FLEXCAN2_TX	0x0b0b0
+			MX6UL_PAD_LCD_DATA11__FLEXCAN2_RX	0x0b0b0
+		>;
+	};
+
+	princtrl_flexcan2_en: flexcan2engrp {
+		fsl,pins = <
+			MX6UL_PAD_UART1_CTS_B__GPIO1_IO18	0x17059
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO00__I2C2_SCL	0xb0
+			MX6UL_PAD_GPIO1_IO01__I2C2_SDA	0xb0
+		>;
+	};
+
+	pinctrl_i2c2_gpio: i2c2gpiogrp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO00__GPIO1_IO00	0xb0
+			MX6UL_PAD_GPIO1_IO01__GPIO1_IO01	0xb0
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA01__I2C3_SCL	0xb0
+			MX6UL_PAD_LCD_DATA00__I2C3_SDA	0xb0
+		>;
+	};
+
+	pinctrl_i2c3_gpio: i2c3gpiogrp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA01__GPIO3_IO06	0xb0
+			MX6UL_PAD_LCD_DATA00__GPIO3_IO05	0xb0
+		>;
+	};
+
+	pinctrl_i2c4: i2c4grp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA03__I2C4_SCL	0xb0
+			MX6UL_PAD_LCD_DATA02__I2C4_SDA	0xb0
+		>;
+	};
+
+	pinctrl_i2c4_gpio: i2c4gpiogrp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA03__GPIO3_IO08	0xb0
+			MX6UL_PAD_LCD_DATA02__GPIO3_IO07	0xb0
+		>;
+	};
+
+	pinctrl_pwm3: pwm3grp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO04__PWM3_OUT	0x0b0b0
+		>;
+	};
+
+	pinctrl_pwm6: pwm6grp {
+		fsl,pins = <
+			MX6UL_PAD_JTAG_TDI__PWM6_OUT	0x0b0b0
+		>;
+	};
+
+	pinctrl_pwm7: pwm7grp {
+		fsl,pins = <
+			MX6UL_PAD_JTAG_TCK__PWM7_OUT	0x0b0b0
+		>;
+	};
+
+	pinctrl_pwm8: pwm8grp {
+		fsl,pins = <
+			MX6UL_PAD_JTAG_TRST_B__PWM8_OUT	0x0b0b0
+		>;
+	};
+
+	pinctrl_s25fl064_hold: s25fl064holdgrp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA12__GPIO3_IO17	0x100b1
+		>;
+	};
+
+	pinctrl_sai2: sai2grp {
+		fsl,pins = <
+			MX6UL_PAD_JTAG_TDI__SAI2_TX_BCLK	0x17088
+			MX6UL_PAD_JTAG_TDO__SAI2_TX_SYNC	0x17088
+			MX6UL_PAD_JTAG_TRST_B__SAI2_TX_DATA	0x11088
+			MX6UL_PAD_JTAG_TCK__SAI2_RX_DATA	0x11088
+			MX6UL_PAD_JTAG_TMS__SAI2_MCLK		0x17088
+		>;
+	};
+
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <
+			MX6UL_PAD_UART3_TX_DATA__UART3_DCE_TX	0x1b0b1
+			MX6UL_PAD_UART3_RX_DATA__UART3_DCE_RX	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart4: uart4grp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_CLK__UART4_DCE_TX		0x1b0b1
+			MX6UL_PAD_LCD_ENABLE__UART4_DCE_RX	0x1b0b1
+			MX6UL_PAD_LCD_HSYNC__GPIO3_IO02	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart5: uart5grp {
+		fsl,pins = <
+			MX6UL_PAD_UART5_TX_DATA__UART5_DCE_TX	0x1b0b1
+			MX6UL_PAD_UART5_RX_DATA__UART5_DCE_RX	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart7: uart7grp {
+		fsl,pins = <
+			MX6UL_PAD_LCD_DATA16__UART7_DCE_TX	0x1b0b1
+			MX6UL_PAD_LCD_DATA17__UART7_DCE_RX	0x1b0b1
+		>;
+	};
+
+	pinctrl_usb_otg1: usbotg1grp {
+		fsl,pins = <
+			MX6UL_PAD_CSI_DATA06__GPIO4_IO27	0x80
+		>;
+	};
+
+	pinctrl_usbotg1pwr: usbotg1pwrgrp {
+		fsl,pins = <
+			MX6UL_PAD_CSI_DATA07__GPIO4_IO28	0x17059
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x17059
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x10059
+			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x17059
+			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x17059
+			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x17059
+			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x17059
+			MX6UL_PAD_UART1_RTS_B__GPIO1_IO19	0x17059
+		>;
+	};
+
+	pinctrl_usdhc1_100mhz: usdhc1100mhzgrp {
+		fsl,pins = <
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x170b9
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x100b9
+			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x170b9
+			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x170b9
+			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x170b9
+			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x170b9
+		>;
+	};
+
+	pinctrl_usdhc1_200mhz: usdhc1200mhzgrp {
+		fsl,pins = <
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x170f9
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x100f9
+			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x170f9
+			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x170f9
+			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x170f9
+			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x170f9
+		>;
+	};
+
+	pinctrl_user_leds: userledsgrp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO03__GPIO1_IO03	0x79
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6ull-pinfunc.h b/arch/arm/boot/dts/imx6ull-pinfunc.h
index eb025a9d4759..7328d4ef8559 100644
--- a/arch/arm/boot/dts/imx6ull-pinfunc.h
+++ b/arch/arm/boot/dts/imx6ull-pinfunc.h
@@ -82,6 +82,6 @@
 #define MX6ULL_PAD_CSI_DATA04__ESAI_TX_FS                         0x01F4 0x0480 0x0000 0x9 0x0
 #define MX6ULL_PAD_CSI_DATA05__ESAI_TX_CLK                        0x01F8 0x0484 0x0000 0x9 0x0
 #define MX6ULL_PAD_CSI_DATA06__ESAI_TX5_RX0                       0x01FC 0x0488 0x0000 0x9 0x0
-#define MX6ULL_PAD_CSI_DATA07__ESAI_T0                            0x0200 0x048C 0x0000 0x9 0x0
+#define MX6ULL_PAD_CSI_DATA07__ESAI_TX0                           0x0200 0x048C 0x0000 0x9 0x0
 
 #endif /* __DTS_IMX6ULL_PINFUNC_H */
diff --git a/arch/arm/boot/dts/imx6ull-tqma6ull2-mba6ulx.dts b/arch/arm/boot/dts/imx6ull-tqma6ull2-mba6ulx.dts
new file mode 100644
index 000000000000..e593b7036fc7
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ull-tqma6ull2-mba6ulx.dts
@@ -0,0 +1,15 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2018-2022 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+/dts-v1/;
+
+#include "imx6ull-tqma6ull2.dtsi"
+#include "mba6ulx.dtsi"
+
+/ {
+	model = "TQ-Systems TQMa6ULL2 SoM on MBa6ULx board";
+	compatible = "tq,imx6ull-tqma6ull2-mba6ulx", "tq,imx6ull-tqma6ull2", "fsl,imx6ull";
+};
diff --git a/arch/arm/boot/dts/imx6ull-tqma6ull2.dtsi b/arch/arm/boot/dts/imx6ull-tqma6ull2.dtsi
new file mode 100644
index 000000000000..8541cb3f3b3e
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ull-tqma6ull2.dtsi
@@ -0,0 +1,76 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2018-2022 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+#include "imx6ull.dtsi"
+#include "imx6ul-tqma6ul-common.dtsi"
+#include "imx6ul-tqma6ulx-common.dtsi"
+
+/ {
+	model = "TQ-Systems TQMa6ULL2 SoM";
+	compatible = "tq,imx6ull-tqma6ull2", "fsl,imx6ull";
+};
+
+&usdhc2 {
+	fsl,tuning-step = <6>;
+	/* Errata ERR010450 Workaround */
+	max-frequency = <99000000>;
+	assigned-clocks = <&clks IMX6UL_CLK_USDHC2_SEL>, <&clks IMX6UL_CLK_USDHC2>;
+	assigned-clock-parents = <&clks IMX6UL_CLK_PLL2_PFD2>;
+	assigned-clock-rates = <0>, <198000000>;
+};
+
+&iomuxc {
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK		0x00017031
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD		0x00017039
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0	0x00017039
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1	0x00017039
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2	0x00017039
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3	0x00017039
+			MX6UL_PAD_NAND_DATA04__USDHC2_DATA4	0x00017039
+			MX6UL_PAD_NAND_DATA05__USDHC2_DATA5	0x00017039
+			MX6UL_PAD_NAND_DATA06__USDHC2_DATA6	0x00017039
+			MX6UL_PAD_NAND_DATA07__USDHC2_DATA7	0x00017039
+			/* rst */
+			MX6UL_PAD_NAND_ALE__GPIO4_IO10		0x0001b051
+		>;
+	};
+
+	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK		0x000170f1
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD		0x000170f1
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0	0x000170f1
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1	0x000170f1
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2	0x000170f1
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3	0x000170f1
+			MX6UL_PAD_NAND_DATA04__USDHC2_DATA4	0x000170f1
+			MX6UL_PAD_NAND_DATA05__USDHC2_DATA5	0x000170f1
+			MX6UL_PAD_NAND_DATA06__USDHC2_DATA6	0x000170f1
+			MX6UL_PAD_NAND_DATA07__USDHC2_DATA7	0x000170f1
+			/* rst */
+			MX6UL_PAD_NAND_ALE__GPIO4_IO10		0x0001b051
+		>;
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK		0x000170f1
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD		0x000170f1
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0	0x000170f1
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1	0x000170f1
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2	0x000170f1
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3	0x000170f1
+			MX6UL_PAD_NAND_DATA04__USDHC2_DATA4	0x000170f1
+			MX6UL_PAD_NAND_DATA05__USDHC2_DATA5	0x000170f1
+			MX6UL_PAD_NAND_DATA06__USDHC2_DATA6	0x000170f1
+			MX6UL_PAD_NAND_DATA07__USDHC2_DATA7	0x000170f1
+			/* rst */
+			MX6UL_PAD_NAND_ALE__GPIO4_IO10		0x0001b051
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6ull-tqma6ull2l-mba6ulx.dts b/arch/arm/boot/dts/imx6ull-tqma6ull2l-mba6ulx.dts
new file mode 100644
index 000000000000..33437aae9822
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ull-tqma6ull2l-mba6ulx.dts
@@ -0,0 +1,15 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2018-2022 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+/dts-v1/;
+
+#include "imx6ull-tqma6ull2l.dtsi"
+#include "mba6ulx.dtsi"
+
+/ {
+	model = "TQ Systems TQMa6ULL2L SoM on MBa6ULx board";
+	compatible = "tq,imx6ull-tqma6ull2l-mba6ulx", "tq,imx6ull-tqma6ull2l", "fsl,imx6ull";
+};
diff --git a/arch/arm/boot/dts/imx6ull-tqma6ull2l.dtsi b/arch/arm/boot/dts/imx6ull-tqma6ull2l.dtsi
new file mode 100644
index 000000000000..be593d47e3b1
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ull-tqma6ull2l.dtsi
@@ -0,0 +1,76 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2018-2022 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+#include "imx6ull.dtsi"
+#include "imx6ul-tqma6ul-common.dtsi"
+#include "imx6ul-tqma6ulxl-common.dtsi"
+
+/ {
+	model = "TQ Systems TQMa6ULL2L SoM";
+	compatible = "tq,imx6ull-tqma6ull2l", "fsl,imx6ull";
+};
+
+&usdhc2 {
+	fsl,tuning-step = <6>;
+	/* Errata ERR010450 Workaround */
+	max-frequency = <99000000>;
+	assigned-clocks = <&clks IMX6UL_CLK_USDHC2_SEL>, <&clks IMX6UL_CLK_USDHC2>;
+	assigned-clock-parents = <&clks IMX6UL_CLK_PLL2_PFD2>;
+	assigned-clock-rates = <0>, <198000000>;
+};
+
+&iomuxc {
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK		0x00017031
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD		0x00017039
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0	0x00017039
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1	0x00017039
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2	0x00017039
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3	0x00017039
+			MX6UL_PAD_NAND_DATA04__USDHC2_DATA4	0x00017039
+			MX6UL_PAD_NAND_DATA05__USDHC2_DATA5	0x00017039
+			MX6UL_PAD_NAND_DATA06__USDHC2_DATA6	0x00017039
+			MX6UL_PAD_NAND_DATA07__USDHC2_DATA7	0x00017039
+			/* rst */
+			MX6UL_PAD_NAND_ALE__GPIO4_IO10		0x0001b051
+		>;
+	};
+
+	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK		0x000170f1
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD		0x000170f1
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0	0x000170f1
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1	0x000170f1
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2	0x000170f1
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3	0x000170f1
+			MX6UL_PAD_NAND_DATA04__USDHC2_DATA4	0x000170f1
+			MX6UL_PAD_NAND_DATA05__USDHC2_DATA5	0x000170f1
+			MX6UL_PAD_NAND_DATA06__USDHC2_DATA6	0x000170f1
+			MX6UL_PAD_NAND_DATA07__USDHC2_DATA7	0x000170f1
+			/* rst */
+			MX6UL_PAD_NAND_ALE__GPIO4_IO10		0x0001b051
+		>;
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+		fsl,pins = <
+			MX6UL_PAD_NAND_RE_B__USDHC2_CLK		0x000170f1
+			MX6UL_PAD_NAND_WE_B__USDHC2_CMD		0x000170f1
+			MX6UL_PAD_NAND_DATA00__USDHC2_DATA0	0x000170f1
+			MX6UL_PAD_NAND_DATA01__USDHC2_DATA1	0x000170f1
+			MX6UL_PAD_NAND_DATA02__USDHC2_DATA2	0x000170f1
+			MX6UL_PAD_NAND_DATA03__USDHC2_DATA3	0x000170f1
+			MX6UL_PAD_NAND_DATA04__USDHC2_DATA4	0x000170f1
+			MX6UL_PAD_NAND_DATA05__USDHC2_DATA5	0x000170f1
+			MX6UL_PAD_NAND_DATA06__USDHC2_DATA6	0x000170f1
+			MX6UL_PAD_NAND_DATA07__USDHC2_DATA7	0x000170f1
+			/* rst */
+			MX6UL_PAD_NAND_ALE__GPIO4_IO10		0x0001b051
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx6ull.dtsi b/arch/arm/boot/dts/imx6ull.dtsi
index 9bf67490ac49..2bccd45e9fc2 100644
--- a/arch/arm/boot/dts/imx6ull.dtsi
+++ b/arch/arm/boot/dts/imx6ull.dtsi
@@ -50,7 +50,7 @@
 };
 
 / {
-	soc {
+	soc: soc {
 		aips3: bus@2200000 {
 			compatible = "fsl,aips-bus", "simple-bus";
 			#address-cells = <1>;
diff --git a/arch/arm/boot/dts/imx6ulz-bsh-smm-m2.dts b/arch/arm/boot/dts/imx6ulz-bsh-smm-m2.dts
new file mode 100644
index 000000000000..c92e4e2f6ab9
--- /dev/null
+++ b/arch/arm/boot/dts/imx6ulz-bsh-smm-m2.dts
@@ -0,0 +1,150 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright (C) 2021 BSH Hausgeraete GmbH
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+#include "imx6ulz.dtsi"
+
+/ {
+	model = "BSH SMM M2";
+	compatible = "bsh,imx6ulz-bsh-smm-m2", "fsl,imx6ull", "fsl,imx6ulz";
+
+	chosen {
+		stdout-path = &uart4;
+	};
+
+	usdhc2_pwrseq: usdhc2-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&gpio2 21 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&gpmi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpmi_nand>;
+	nand-on-flash-bbt;
+	status = "okay";
+};
+
+&snvs_poweroff {
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	uart-has-rtscts;
+	status = "okay";
+
+	bluetooth {
+		compatible = "brcm,bcm4330-bt";
+		max-speed = <3000000>;
+		shutdown-gpios = <&gpio1 1 GPIO_ACTIVE_HIGH>;
+		device-wakeup-gpios = <&gpio2 17 GPIO_ACTIVE_HIGH>;
+		host-wakeup-gpios = <&gpio2 13 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+	status = "okay";
+};
+
+&usbotg1 {
+	dr_mode = "peripheral";
+	srp-disable;
+	hnp-disable;
+	adp-disable;
+	status = "okay";
+};
+
+&usbphy1 {
+	fsl,tx-d-cal = <106>;
+};
+
+&usdhc2 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wlan>;
+	bus-width = <4>;
+	no-1-8-v;
+	non-removable;
+	cap-power-off-card;
+	keep-power-in-suspend;
+	cap-sdio-irq;
+	mmc-pwrseq = <&usdhc2_pwrseq>;
+	status = "okay";
+
+	brcmf: wifi@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+		interrupt-parent = <&gpio1>;
+		interrupts = <18 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "host-wake";
+	};
+};
+
+&wdog1 {
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_gpmi_nand: gpmi-nand {
+		fsl,pins = <
+			MX6UL_PAD_NAND_CLE__RAWNAND_CLE		0xb0b1
+			MX6UL_PAD_NAND_ALE__RAWNAND_ALE		0xb0b1
+			MX6UL_PAD_NAND_WP_B__RAWNAND_WP_B	0xb0b1
+			MX6UL_PAD_NAND_READY_B__RAWNAND_READY_B	0xb000
+			MX6UL_PAD_NAND_CE0_B__RAWNAND_CE0_B	0xb0b1
+			MX6UL_PAD_NAND_RE_B__RAWNAND_RE_B	0xb0b1
+			MX6UL_PAD_NAND_WE_B__RAWNAND_WE_B	0xb0b1
+			MX6UL_PAD_NAND_DATA00__RAWNAND_DATA00	0xb0b1
+			MX6UL_PAD_NAND_DATA01__RAWNAND_DATA01	0xb0b1
+			MX6UL_PAD_NAND_DATA02__RAWNAND_DATA02	0xb0b1
+			MX6UL_PAD_NAND_DATA03__RAWNAND_DATA03	0xb0b1
+			MX6UL_PAD_NAND_DATA04__RAWNAND_DATA04	0xb0b1
+			MX6UL_PAD_NAND_DATA05__RAWNAND_DATA05	0xb0b1
+			MX6UL_PAD_NAND_DATA06__RAWNAND_DATA06	0xb0b1
+			MX6UL_PAD_NAND_DATA07__RAWNAND_DATA07	0xb0b1
+		>;
+	};
+
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <
+			MX6UL_PAD_UART3_TX_DATA__UART3_DCE_TX	0x1b0b1
+			MX6UL_PAD_UART3_RX_DATA__UART3_DCE_RX	0x1b099
+			MX6UL_PAD_UART3_RTS_B__UART3_DCE_RTS	0x1b0b1
+			MX6UL_PAD_UART3_CTS_B__UART3_DCE_CTS	0x1b099
+			MX6UL_PAD_GPIO1_IO01__GPIO1_IO01	0x79		/* BT_REG_ON */
+			MX6UL_PAD_SD1_CLK__GPIO2_IO17		0x100b1		/* BT_DEV_WAKE out */
+			MX6UL_PAD_ENET2_TX_EN__GPIO2_IO13	0x1b0b0		/* BT_HOST_WAKE in */
+		>;
+	};
+
+	pinctrl_uart4: uart4grp {
+		fsl,pins = <
+			MX6UL_PAD_UART4_TX_DATA__UART4_DCE_TX	0x1b0b1
+			MX6UL_PAD_UART4_RX_DATA__UART4_DCE_RX	0x1b0b1
+		>;
+	};
+
+	pinctrl_wlan: wlangrp {
+		fsl,pins = <
+			MX6UL_PAD_CSI_HSYNC__USDHC2_CMD		0x17059
+			MX6UL_PAD_CSI_VSYNC__USDHC2_CLK		0x10059
+			MX6UL_PAD_CSI_DATA00__USDHC2_DATA0	0x17059
+			MX6UL_PAD_CSI_DATA01__USDHC2_DATA1	0x17059
+			MX6UL_PAD_CSI_DATA02__USDHC2_DATA2	0x17059
+			MX6UL_PAD_CSI_DATA03__USDHC2_DATA3	0x17059
+			MX6UL_PAD_SD1_DATA3__GPIO2_IO21		0x79		/* WL_REG_ON */
+			MX6UL_PAD_UART2_CTS_B__GPIO1_IO22	0x100b1		/* WL_DEV_WAKE - WiFi_GPIO_4 - WiFi FW UART */
+			MX6UL_PAD_UART1_CTS_B__GPIO1_IO18	0x1b0b1		/* WL_HOST_WAKE - WIFI_GPIO_0 - OOB IRQ */
+			MX6UL_PAD_ENET1_RX_EN__OSC32K_32K_OUT	0x4001b031	/* OSC 32Khz wifi clk in */
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx7-colibri-aster.dtsi b/arch/arm/boot/dts/imx7-colibri-aster.dtsi
index 139188eb9f40..fa488a6de0d4 100644
--- a/arch/arm/boot/dts/imx7-colibri-aster.dtsi
+++ b/arch/arm/boot/dts/imx7-colibri-aster.dtsi
@@ -1,169 +1,79 @@
-// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
 /*
- * Copyright 2017-2020 Toradex AG
- *
+ * Copyright 2017-2022 Toradex
  */
 
-
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/pwm/pwm.h>
-
-/ {
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	gpio-keys {
-		compatible = "gpio-keys";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_gpiokeys>;
-
-		power {
-			label = "Wake-Up";
-			gpios = <&gpio1 1 GPIO_ACTIVE_HIGH>;
-			linux,code = <KEY_WAKEUP>;
-			debounce-interval = <10>;
-			wakeup-source;
-		};
-	};
-
-	panel: panel {
-		compatible = "edt,et057090dhu";
-		backlight = <&bl>;
-		power-supply = <&reg_3v3>;
-
-		port {
-			panel_in: endpoint {
-				remote-endpoint = <&lcdif_out>;
-			};
-		};
-	};
-
-	reg_3v3: regulator-3v3 {
-		compatible = "regulator-fixed";
-		regulator-name = "3.3V";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-	};
-
-	reg_5v0: regulator-5v0 {
-		compatible = "regulator-fixed";
-		regulator-name = "5V";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-	};
-
-	reg_usbh_vbus: regulator-usbh-vbus {
-		compatible = "regulator-fixed";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_usbh_reg>;
-		regulator-name = "VCC_USB[1-4]";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-		gpio = <&gpio4 7 GPIO_ACTIVE_LOW>;
-		vin-supply = <&reg_5v0>;
-	};
-};
-
+/* Colibri AD0 to AD3 */
 &adc1 {
 	status = "okay";
 };
 
-/*
- * ADC2 is not available on the Aster board and
- * conflicts with AD7879 resistive touchscreen.
- */
-&adc2 {
-	status = "disabled";
-};
-
-&bl {
-	brightness-levels = <0 4 8 16 32 64 128 255>;
-	default-brightness-level = <6>;
-	power-supply = <&reg_3v3>;
+/* Colibri SSP */
+&ecspi3 {
+	cs-gpios = <
+		&gpio4 11 GPIO_ACTIVE_LOW /* SODIMM 86 / regular SSPFRM as UNO_SPI_CS or  */
+		&gpio4 23 GPIO_ACTIVE_LOW /* SODIMM 65 / already muxed pinctrl_gpio2 as SPI_CE0_N */
+		&gpio4 22 GPIO_ACTIVE_LOW /* SODIMM 85 / already muxed pinctrl_gpio2 as SPI_CE1_N */
+	>;
 	status = "okay";
 };
 
+/* Colibri Fast Ethernet */
 &fec1 {
 	status = "okay";
 };
 
+/* Colibri I2C: I2C3_SDA/SCL on SODIMM 194/196 */
 &i2c4 {
 	status = "okay";
-
-	/* Microchip/Atmel maxtouch controller */
-	touchscreen@4a {
-		compatible = "atmel,maxtouch";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_gpiotouch>;
-		reg = <0x4a>;
-		interrupt-parent = <&gpio2>;
-		interrupts = <15 IRQ_TYPE_EDGE_FALLING>;	/* SODIMM 107 */
-		reset-gpios = <&gpio2 28 GPIO_ACTIVE_LOW>;	/* SODIMM 106 */
-	};
-
-	/* M41T0M6 real time clock on carrier board */
-	rtc: m41t0m6@68 {
-		compatible = "st,m41t0";
-		reg = <0x68>;
-	};
-};
-
-&iomuxc {
-	pinctrl_gpiotouch: touchgpios {
-		fsl,pins = <
-			MX7D_PAD_EPDC_DATA15__GPIO2_IO15        0x74
-			MX7D_PAD_EPDC_BDR0__GPIO2_IO28          0x14
-		>;
-	};
-};
-
-&lcdif {
-	status = "okay";
-
-	port {
-		lcdif_out: endpoint {
-			remote-endpoint = <&panel_in>;
-		};
-	};
 };
 
+/* Colibri PWM<A> */
 &pwm1 {
 	status = "okay";
 };
 
+/* Colibri PWM<B> */
 &pwm2 {
 	status = "okay";
 };
 
+/* Colibri PWM<C> */
 &pwm3 {
 	status = "okay";
 };
 
+/* Colibri PWM<D> */
 &pwm4 {
 	status = "okay";
 };
 
+/* M41T0M6 real time clock */
+&rtc {
+	status = "okay";
+};
+
+/* Colibri UART_A */
 &uart1 {
 	status = "okay";
 };
 
+/* Colibri UART_B */
 &uart2 {
 	status = "okay";
 };
 
+/* Colibri UART_C */
 &uart3 {
 	status = "okay";
 };
 
+/* Colibri USBC */
 &usbotg1 {
 	status = "okay";
 };
 
+/* Colibri MMC/SD */
 &usdhc1 {
-	keep-power-in-suspend;
-	no-1-8-v;
-	wakeup-source;
-	vmmc-supply = <&reg_3v3>;
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/imx7-colibri-eval-v3.dtsi b/arch/arm/boot/dts/imx7-colibri-eval-v3.dtsi
index 3caf450735d7..826f13da5b81 100644
--- a/arch/arm/boot/dts/imx7-colibri-eval-v3.dtsi
+++ b/arch/arm/boot/dts/imx7-colibri-eval-v3.dtsi
@@ -1,194 +1,110 @@
-// SPDX-License-Identifier: GPL-2.0+ OR MIT
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
 /*
- * Copyright 2016-2020 Toradex
+ * Copyright 2016-2022 Toradex
  */
 
 / {
-	aliases {
-		rtc0 = &rtc;
-		rtc1 = &snvs_rtc;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	/* fixed crystal dedicated to mpc258x */
+	/* Fixed crystal dedicated to MCP2515. */
 	clk16m: clk16m {
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
 		clock-frequency = <16000000>;
 	};
-
-	gpio-keys {
-		compatible = "gpio-keys";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_gpiokeys>;
-
-		power {
-			label = "Wake-Up";
-			gpios = <&gpio1 1 GPIO_ACTIVE_HIGH>;
-			linux,code = <KEY_WAKEUP>;
-			debounce-interval = <10>;
-			wakeup-source;
-		};
-	};
-
-	panel: panel {
-		compatible = "edt,et057090dhu";
-		backlight = <&bl>;
-		power-supply = <&reg_3v3>;
-
-		port {
-			panel_in: endpoint {
-				remote-endpoint = <&lcdif_out>;
-			};
-		};
-	};
-
-	reg_3v3: regulator-3v3 {
-		compatible = "regulator-fixed";
-		regulator-name = "3.3V";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-	};
-
-	reg_5v0: regulator-5v0 {
-		compatible = "regulator-fixed";
-		regulator-name = "5V";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-	};
-
-	reg_usbh_vbus: regulator-usbh-vbus {
-		compatible = "regulator-fixed";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_usbh_reg>;
-		regulator-name = "VCC_USB[1-4]";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-		gpio = <&gpio4 7 GPIO_ACTIVE_LOW>;
-		vin-supply = <&reg_5v0>;
-	};
-};
-
-&bl {
-	brightness-levels = <0 4 8 16 32 64 128 255>;
-	default-brightness-level = <6>;
-	power-supply = <&reg_3v3>;
-
-	status = "okay";
 };
 
+/* Colibri AD0 to AD3 */
 &adc1 {
 	status = "okay";
 };
 
-&adc2 {
-	status = "okay";
+/*
+ * The Atmel maxtouch controller uses SODIMM 28/30, also used for PWM<B>, PWM<C>, aka pwm2, pwm3.
+ * So if you enable following capacitive touch controller, disable pwm2/pwm3 first.
+ */
+&atmel_mxt_ts {
+	interrupt-parent = <&gpio1>;
+	interrupts = <9 IRQ_TYPE_EDGE_FALLING>;		/* SODIMM 28 / INT */
+	pinctrl-0 = <&pinctrl_atmel_adapter>;
+	reset-gpios = <&gpio1 10 GPIO_ACTIVE_LOW>;	/* SODIMM 30 / RST */
+	status = "disabled";
 };
 
+/* Colibri SSP */
 &ecspi3 {
 	status = "okay";
 
 	mcp2515: can@0 {
+		clocks = <&clk16m>;
 		compatible = "microchip,mcp2515";
+		interrupt-parent = <&gpio5>;
+		interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_can_int>;
 		reg = <0>;
-		clocks = <&clk16m>;
-		interrupt-parent = <&gpio5>;
-		interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
 		spi-max-frequency = <10000000>;
 		vdd-supply = <&reg_3v3>;
 		xceiver-supply = <&reg_5v0>;
-		status = "okay";
 	};
 };
 
+/* Colibri Fast Ethernet */
 &fec1 {
 	status = "okay";
 };
 
+/* Colibri I2C: I2C3_SDA/SCL on SODIMM 194/196 */
 &i2c4 {
 	status = "okay";
-
-	/*
-	 * Touchscreen is using SODIMM 28/30, also used for PWM<B>, PWM<C>,
-	 * aka pwm2, pwm3. so if you enable touchscreen, disable the pwms
-	 */
-	touchscreen@4a {
-		compatible = "atmel,maxtouch";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_gpiotouch>;
-		reg = <0x4a>;
-		interrupt-parent = <&gpio1>;
-		interrupts = <9 IRQ_TYPE_EDGE_FALLING>;		/* SODIMM 28 */
-		reset-gpios = <&gpio1 10 GPIO_ACTIVE_LOW>;	/* SODIMM 30 */
-		status = "disabled";
-	};
-
-	/* M41T0M6 real time clock on carrier board */
-	rtc: m41t0m6@68 {
-		compatible = "st,m41t0";
-		reg = <0x68>;
-	};
-};
-
-&lcdif {
-	status = "okay";
-
-	port {
-		lcdif_out: endpoint {
-			remote-endpoint = <&panel_in>;
-		};
-	};
 };
 
+/* Colibri PWM<A> */
 &pwm1 {
 	status = "okay";
 };
 
+/* Colibri PWM<B> */
 &pwm2 {
+	/* The pwm2 should be disabled to enable atmel_mxt_ts touchscreen for adapter. */
 	status = "okay";
 };
 
+/* Colibri PWM<C> */
 &pwm3 {
+	/* The pwm3 should be disabled to enable atmel_mxt_ts touchscreen for adapter. */
 	status = "okay";
 };
 
+/* Colibri PWM<D> */
 &pwm4 {
 	status = "okay";
 };
 
+/* M41T0M6 real time clock */
+&rtc {
+	status = "okay";
+};
+
+/* Colibri UART_A */
 &uart1 {
 	status = "okay";
 };
 
+/* Colibri UART_B */
 &uart2 {
 	status = "okay";
 };
 
+/* Colibri UART_C */
 &uart3 {
 	status = "okay";
 };
 
+/* Colibri USBC */
 &usbotg1 {
 	status = "okay";
 };
 
+/* Colibri MMC/SD */
 &usdhc1 {
-	keep-power-in-suspend;
-	wakeup-source;
-	vmmc-supply = <&reg_3v3>;
 	status = "okay";
 };
-
-&iomuxc {
-	pinctrl_gpiotouch: touchgpios {
-		fsl,pins = <
-			MX7D_PAD_GPIO1_IO09__GPIO1_IO9		0x74
-			MX7D_PAD_GPIO1_IO10__GPIO1_IO10		0x14
-		>;
-	};
-};
diff --git a/arch/arm/boot/dts/imx7-colibri-iris-v2.dtsi b/arch/arm/boot/dts/imx7-colibri-iris-v2.dtsi
new file mode 100644
index 000000000000..6e199613583c
--- /dev/null
+++ b/arch/arm/boot/dts/imx7-colibri-iris-v2.dtsi
@@ -0,0 +1,112 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/ {
+	reg_3v3_vmmc: regulator-3v3-vmmc {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio5 16 GPIO_ACTIVE_HIGH>; /* SODIMM 100 */
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "3v3_vmmc";
+		startup-delay-us = <100>;
+	};
+};
+
+/* Colibri AD0 to AD3 */
+&adc1 {
+	status = "okay";
+};
+
+/* Colibri SSP */
+&ecspi3 {
+	status = "okay";
+};
+
+/* Colibri Fast Ethernet */
+&fec1 {
+	status = "okay";
+};
+
+&gpio2 {
+	/*
+	 * uart_b_c_on_x14_enable turns the UART transceiver for UART2 and 5 on. If one wants to
+	 * turn the transceiver off, that property has to be deleted and the gpio handled in
+	 * userspace.
+	 * The same applies to uart_a_on_x13_enable where the UART_A transceiver is turned on.
+	 */
+	uart-b-c-on-x14-enable-hog {
+		gpio-hog;
+		gpios = <27 GPIO_ACTIVE_HIGH>; /* SODIMM 104 */
+		output-high;
+	};
+};
+
+&gpio5 {
+	uart-a-on-x13-enable-hog {
+		gpio-hog;
+		gpios = <17 GPIO_ACTIVE_HIGH>; /* SODIMM 102 */
+		output-high;
+	};
+};
+
+/* Colibri I2C: I2C3_SDA/SCL on SODIMM 194/196 */
+&i2c4 {
+	status = "okay";
+};
+
+/* Colibri PWM<A> */
+&pwm1 {
+	status = "okay";
+};
+
+/* Colibri PWM<B> */
+&pwm2 {
+	status = "okay";
+};
+
+/* Colibri PWM<C> */
+&pwm3 {
+	status = "okay";
+};
+
+/* Colibri PWM<D> */
+&pwm4 {
+	status = "okay";
+};
+
+/* M41T0M6 real time clock */
+&rtc {
+	status = "okay";
+};
+
+/* Colibri UART_A */
+&uart1 {
+	status = "okay";
+};
+
+/* Colibri UART_B */
+&uart2 {
+	status = "okay";
+};
+
+/* Colibri UART_C */
+&uart3 {
+	status = "okay";
+};
+
+/* Colibri USBC */
+&usbotg1 {
+	status = "okay";
+};
+
+/* Colibri MMC/SD, UHS-I capable uSD slot */
+&usdhc1 {
+	cap-power-off-card;
+	/delete-property/ keep-power-in-suspend;
+	/delete-property/ no-1-8-v;
+	vmmc-supply = <&reg_3v3_vmmc>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx7-colibri-iris.dtsi b/arch/arm/boot/dts/imx7-colibri-iris.dtsi
new file mode 100644
index 000000000000..175c5d478d2e
--- /dev/null
+++ b/arch/arm/boot/dts/imx7-colibri-iris.dtsi
@@ -0,0 +1,108 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/* Colibri AD0 to AD3 */
+&adc1 {
+	status = "okay";
+};
+
+/*
+ * The Atmel maxtouch controller uses SODIMM 28/30, also used for PWM<B>, PWM<C>, aka pwm2, pwm3.
+ * So if you enable following capacitive touch controller, disable pwm2/pwm3 first.
+ */
+&atmel_mxt_ts {
+	interrupt-parent = <&gpio1>;
+	interrupts = <9 IRQ_TYPE_EDGE_FALLING>;		/* SODIMM 28 / INT */
+	pinctrl-0 = <&pinctrl_atmel_adapter>;
+	reset-gpios = <&gpio1 10 GPIO_ACTIVE_LOW>;	/* SODIMM 30 / RST */
+};
+
+/* Colibri SSP */
+&ecspi3 {
+	status = "okay";
+};
+
+/* Colibri Fast Ethernet */
+&fec1 {
+	status = "okay";
+};
+
+&gpio2 {
+	/*
+	 * uart25 turns the UART transceiver for UART2 and 5 on. If one wants to turn the
+	 * transceiver off, that property has to be deleted and the gpio handled in userspace.
+	 * The same applies to uart1_tx_on where the UART1 transceiver is turned on.
+	 */
+	uart25-tx-on-hog {
+		gpio-hog;
+		gpios = <27 GPIO_ACTIVE_HIGH>; /* SODIMM 104 */
+		output-high;
+	};
+};
+
+&gpio5 {
+	uart1-tx-on-hog {
+		gpio-hog;
+		gpios = <17 GPIO_ACTIVE_HIGH>; /* SODIMM 102 */
+		output-high;
+	};
+};
+
+/* Colibri I2C: I2C3_SDA/SCL on SODIMM 194/196 */
+&i2c4 {
+	status = "okay";
+};
+
+/* Colibri PWM<A> */
+&pwm1 {
+	status = "okay";
+};
+
+/* Colibri PWM<B> */
+&pwm2 {
+	/* The pwm2 should be disabled to enable atmel_mxt_ts touchscreen for adapter. */
+	status = "okay";
+};
+
+/* Colibri PWM<C> */
+&pwm3 {
+	/* The pwm3 should be disabled to enable atmel_mxt_ts touchscreen for adapter. */
+	status = "okay";
+};
+
+/* Colibri PWM<D> */
+&pwm4 {
+	status = "okay";
+};
+
+/* M41T0M6 real time clock */
+&rtc {
+	status = "okay";
+};
+
+/* Colibri UART_A */
+&uart1 {
+	status = "okay";
+};
+
+/* Colibri UART_B */
+&uart2 {
+	status = "okay";
+};
+
+/* Colibri UART_C */
+&uart3 {
+	status = "okay";
+};
+
+/* Colibri USBC */
+&usbotg1 {
+	status = "okay";
+};
+
+/* Colibri MMC/SD */
+&usdhc1 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx7-colibri.dtsi b/arch/arm/boot/dts/imx7-colibri.dtsi
index 62b771c1d5a9..a8c31ee65623 100644
--- a/arch/arm/boot/dts/imx7-colibri.dtsi
+++ b/arch/arm/boot/dts/imx7-colibri.dtsi
@@ -1,96 +1,198 @@
-// SPDX-License-Identifier: GPL-2.0+ OR MIT
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
 /*
- * Copyright 2016-2020 Toradex
+ * Copyright 2016-2022 Toradex
  */
 
+#include <dt-bindings/pwm/pwm.h>
+
 / {
-	bl: backlight {
+	aliases {
+		rtc0 = &rtc;
+		rtc1 = &snvs_rtc;
+	};
+
+	backlight: backlight {
+		brightness-levels = <0 45 63 88 119 158 203 255>;
 		compatible = "pwm-backlight";
+		default-brightness-level = <4>;
+		enable-gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gpio_bl_on>;
-		pwms = <&pwm1 0 5000000 0>;
-		enable-gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;
+		power-supply = <&reg_module_3v3>;
+		pwms = <&pwm1 0 6666667 PWM_POLARITY_INVERTED>;
+		status = "disabled";
 	};
 
-	reg_module_3v3: regulator-module-3v3 {
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	extcon_usbc_det: usbc-det {
+		compatible = "linux,extcon-usb-gpio";
+		debounce = <25>;
+		id-gpio = <&gpio7 14 GPIO_ACTIVE_HIGH>; /* SODIMM 137 / USBC_DET */
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usbc_det>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpiokeys>;
+
+		wakeup {
+			debounce-interval = <10>;
+			gpios = <&gpio1 1 (GPIO_ACTIVE_HIGH | GPIO_PULL_DOWN)>; /* SODIMM 45 */
+			label = "Wake-Up";
+			linux,code = <KEY_WAKEUP>;
+			wakeup-source;
+		};
+	};
+
+	panel_dpi: panel-dpi {
+		backlight = <&backlight>;
+		compatible = "edt,et057090dhu";
+		power-supply = <&reg_3v3>;
+		status = "disabled";
+
+		port {
+			lcd_panel_in: endpoint {
+				remote-endpoint = <&lcdif_out>;
+			};
+		};
+	};
+
+	reg_3v3: regulator-3v3 {
 		compatible = "regulator-fixed";
-		regulator-name = "+V3.3";
-		regulator-min-microvolt = <3300000>;
+		regulator-always-on;
 		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "3.3V";
+	};
+
+	reg_5v0: regulator-5v0 {
+		compatible = "regulator-fixed";
 		regulator-always-on;
+		regulator-max-microvolt = <5000000>;
+		regulator-min-microvolt = <5000000>;
+		regulator-name = "5V";
+	};
+
+	reg_module_3v3: regulator-module-3v3 {
+		compatible = "regulator-fixed";
+		regulator-always-on;
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "+V3.3";
 	};
 
 	reg_module_3v3_avdd: regulator-module-3v3-avdd {
 		compatible = "regulator-fixed";
+		regulator-always-on;
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
 		regulator-name = "+V3.3_AVDD_AUDIO";
+	};
+
+	reg_module_3v3_eth: regulator-module-3v3-eth {
+		compatible = "regulator-fixed";
+		off-on-delay-us = <200000>;
+		regulator-name = "+V3.3_ETH";
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
-		regulator-always-on;
+		regulator-boot-on;
+		startup-delay-us = <200000>;
+		vin-supply = <&reg_LDO1>;
+	};
+
+	reg_usbh_vbus: regulator-usbh-vbus {
+		compatible = "regulator-fixed";
+		gpio = <&gpio4 7 GPIO_ACTIVE_LOW>; /* SODIMM 129 / USBH_PEN */
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usbh_reg>;
+		regulator-max-microvolt = <5000000>;
+		regulator-min-microvolt = <5000000>;
+		regulator-name = "VCC_USB[1-4]";
+		vin-supply = <&reg_5v0>;
 	};
 
 	sound {
 		compatible = "simple-audio-card";
-		simple-audio-card,name = "imx7-sgtl5000";
-		simple-audio-card,format = "i2s";
 		simple-audio-card,bitclock-master = <&dailink_master>;
+		simple-audio-card,format = "i2s";
 		simple-audio-card,frame-master = <&dailink_master>;
+		simple-audio-card,name = "imx7-sgtl5000";
+
 		simple-audio-card,cpu {
 			sound-dai = <&sai1>;
 		};
 
 		dailink_master: simple-audio-card,codec {
+			clocks = <&clks IMX7D_AUDIO_MCLK_ROOT_DIV>;
 			sound-dai = <&codec>;
-			clocks = <&clks IMX7D_AUDIO_MCLK_ROOT_CLK>;
 		};
 	};
 };
 
+/* Colibri AD0 to AD3 */
 &adc1 {
 	vref-supply = <&reg_DCDC3>;
 };
 
-&adc2 {
-	vref-supply = <&reg_DCDC3>;
-};
+/* ADC2 is not available as it conflicts with AD7879 resistive touchscreen. */
 
 &cpu0 {
 	cpu-supply = <&reg_DCDC2>;
 };
 
+/* Colibri SSP */
 &ecspi3 {
+	cs-gpios = <&gpio4 11 GPIO_ACTIVE_LOW>; /* SODIMM 86 / SSPFRM */
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_ecspi3 &pinctrl_ecspi3_cs>;
-	cs-gpios = <&gpio4 11 GPIO_ACTIVE_LOW>;
 };
 
+/* Colibri Fast Ethernet */
 &fec1 {
-	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&pinctrl_enet1>;
-	pinctrl-1 = <&pinctrl_enet1_sleep>;
-	clocks = <&clks IMX7D_ENET_AXI_ROOT_CLK>,
-		<&clks IMX7D_ENET_AXI_ROOT_CLK>,
-		<&clks IMX7D_ENET1_TIME_ROOT_CLK>,
-		<&clks IMX7D_PLL_ENET_MAIN_50M_CLK>;
-	clock-names = "ipg", "ahb", "ptp", "enet_clk_ref";
-	assigned-clocks = <&clks IMX7D_ENET1_TIME_ROOT_SRC>,
-			  <&clks IMX7D_ENET1_TIME_ROOT_CLK>;
 	assigned-clock-parents = <&clks IMX7D_PLL_ENET_MAIN_100M_CLK>;
 	assigned-clock-rates = <0>, <100000000>;
-	phy-mode = "rmii";
-	phy-supply = <&reg_LDO1>;
+	assigned-clocks = <&clks IMX7D_ENET1_TIME_ROOT_SRC>,
+			  <&clks IMX7D_ENET1_TIME_ROOT_CLK>;
+	clock-names = "ipg", "ahb", "ptp", "enet_clk_ref";
+	clocks = <&clks IMX7D_ENET_AXI_ROOT_CLK>,
+		 <&clks IMX7D_ENET_AXI_ROOT_CLK>,
+		 <&clks IMX7D_ENET1_TIME_ROOT_CLK>,
+		 <&clks IMX7D_PLL_ENET_MAIN_50M_CLK>;
 	fsl,magic-packet;
+	phy-handle = <&ethphy0>;
+	phy-mode = "rmii";
+	phy-supply = <&reg_module_3v3_eth>;
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&pinctrl_enet1>;
+	pinctrl-1 = <&pinctrl_enet1_sleep>;
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* Micrel KSZ8041RNL */
+		ethphy0: ethernet-phy@0 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			max-speed = <100>;
+			micrel,led-mode = <0>;
+			reg = <0>;
+		};
+	};
 };
 
 &flexcan1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_flexcan1>;
-	status = "disabled";
 };
 
 &flexcan2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_flexcan2>;
-	status = "disabled";
 };
 
 &gpio1 {
@@ -271,14 +373,16 @@
 			  "SODIMM_137";
 };
 
+/* NAND on such SKUs */
 &gpmi {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_gpmi_nand>;
 	fsl,use-minimum-ecc;
-	nand-on-flash-bbt;
 	nand-ecc-mode = "hw";
+	nand-on-flash-bbt;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpmi_nand>;
 };
 
+/* On-module Power I2C */
 &i2c1 {
 	clock-frequency = <100000>;
 	pinctrl-names = "default", "gpio";
@@ -286,33 +390,33 @@
 	pinctrl-1 = <&pinctrl_i2c1_recovery &pinctrl_i2c1_int>;
 	scl-gpios = <&gpio1 4 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 	sda-gpios = <&gpio1 5 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
-
 	status = "okay";
 
 	codec: sgtl5000@a {
-		compatible = "fsl,sgtl5000";
 		#sound-dai-cells = <0>;
-		reg = <0x0a>;
-		clocks = <&clks IMX7D_AUDIO_MCLK_ROOT_CLK>;
+		clocks = <&clks IMX7D_AUDIO_MCLK_ROOT_DIV>;
+		compatible = "fsl,sgtl5000";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_sai1_mclk>;
+		reg = <0xa>;
 		VDDA-supply = <&reg_module_3v3_avdd>;
-		VDDIO-supply = <&reg_module_3v3>;
 		VDDD-supply = <&reg_DCDC3>;
+		VDDIO-supply = <&reg_module_3v3>;
 	};
 
-	ad7879@2c {
+	ad7879_ts: touchscreen@2c {
+		adi,acquisition-time = /bits/ 8 <1>;
+		adi,averaging = /bits/ 8 <1>;
+		adi,conversion-interval = /bits/ 8 <255>;
+		adi,first-conversion-delay = /bits/ 8 <3>;
+		adi,median-filter-size = /bits/ 8 <2>;
+		adi,resistance-plate-x = <120>;
 		compatible = "adi,ad7879-1";
-		reg = <0x2c>;
 		interrupt-parent = <&gpio1>;
 		interrupts = <13 IRQ_TYPE_EDGE_FALLING>;
+		reg = <0x2c>;
 		touchscreen-max-pressure = <4096>;
-		adi,resistance-plate-x = <120>;
-		adi,first-conversion-delay = /bits/ 8 <3>;
-		adi,acquisition-time = /bits/ 8 <1>;
-		adi,median-filter-size = /bits/ 8 <2>;
-		adi,averaging = /bits/ 8 <1>;
-		adi,conversion-interval = /bits/ 8 <255>;
+		status = "disabled";
 	};
 
 	pmic@33 {
@@ -320,71 +424,81 @@
 		reg = <0x33>;
 
 		regulators {
-			reg_DCDC1: DCDC1 {  /* V1.0_SOC */
-				regulator-min-microvolt = <1000000>;
-				regulator-max-microvolt = <1100000>;
-				regulator-boot-on;
+			reg_DCDC1: DCDC1 {
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1100000>;
+				regulator-min-microvolt = <1000000>;
+				regulator-name = "+V1.0_SOC";
 			};
 
-			reg_DCDC2: DCDC2 { /* V1.1_ARM */
-				regulator-min-microvolt = <975000>;
-				regulator-max-microvolt = <1100000>;
-				regulator-boot-on;
+			reg_DCDC2: DCDC2 {
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1100000>;
+				regulator-min-microvolt = <975000>;
+				regulator-name = "+V1.1_ARM";
 			};
 
-			reg_DCDC3: DCDC3 { /* V1.8 */
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <1800000>;
-				regulator-boot-on;
+			reg_DCDC3: DCDC3 {
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1800000>;
+				regulator-min-microvolt = <1800000>;
+				regulator-name = "+V1.8";
 			};
 
-			reg_DCDC4: DCDC4 { /* V1.35_DRAM */
-				regulator-min-microvolt = <1350000>;
-				regulator-max-microvolt = <1350000>;
-				regulator-boot-on;
+			reg_DCDC4: DCDC4 {
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1350000>;
+				regulator-min-microvolt = <1350000>;
+				regulator-name = "+V1.35_DRAM";
 			};
 
-			reg_LDO1: LDO1 { /* PWR_EN_+V3.3_ETH */
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <3300000>;
+			reg_LDO1: LDO1 {
 				regulator-boot-on;
+				regulator-max-microvolt = <3300000>;
+				regulator-min-microvolt = <3300000>;
+				regulator-name = "PWR_EN_+V3.3_ETH";
 			};
 
-			reg_LDO2: LDO2 { /* +V1.8_SD */
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <3300000>;
-				regulator-boot-on;
+			reg_LDO2: LDO2 {
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <3300000>;
+				regulator-min-microvolt = <1800000>;
+				regulator-name = "+V1.8_SD";
 			};
 
-			reg_LDO3: LDO3 { /* PWR_EN_+V3.3_LPSR */
-				regulator-min-microvolt = <3300000>;
-				regulator-max-microvolt = <3300000>;
-				regulator-boot-on;
+			reg_LDO3: LDO3 {
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <3300000>;
+				regulator-min-microvolt = <3300000>;
+				regulator-name = "PWR_EN_+V3.3_LPSR";
 			};
 
-			reg_LDO4: LDO4 { /* V1.8_LPSR */
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <1800000>;
-				regulator-boot-on;
+			reg_LDO4: LDO4 {
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1800000>;
+				regulator-min-microvolt = <1800000>;
+				regulator-name = "+V1.8_LPSR";
 			};
 
-			reg_LDO5: LDO5 { /* PWR_EN_+V3.3 */
-				regulator-min-microvolt = <3300000>;
-				regulator-max-microvolt = <3300000>;
-				regulator-boot-on;
+			reg_LDO5: LDO5 {
 				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <3300000>;
+				regulator-min-microvolt = <3300000>;
+				regulator-name = "PWR_EN_+V3.3";
 			};
 		};
 	};
 };
 
+/* Colibri I2C: I2C3_SDA/SCL on SODIMM 194/196 */
 &i2c4 {
 	clock-frequency = <100000>;
 	pinctrl-names = "default", "gpio";
@@ -392,36 +506,69 @@
 	pinctrl-1 = <&pinctrl_i2c4_recovery>;
 	scl-gpios = <&gpio7 8 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 	sda-gpios = <&gpio7 9 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "disabled";
+
+	/* Atmel maxtouch controller */
+	atmel_mxt_ts: touchscreen@4a {
+		compatible = "atmel,maxtouch";
+		interrupt-parent = <&gpio2>;
+		interrupts = <15 IRQ_TYPE_EDGE_FALLING>;        /* SODIMM 107 / INT */
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_atmel_connector>;
+		reg = <0x4a>;
+		reset-gpios = <&gpio2 28 GPIO_ACTIVE_LOW>;      /* SODIMM 106 / RST */
+		status = "disabled";
+	};
+
+	/* M41T0M6 real time clock on carrier board */
+	rtc: rtc@68 {
+		compatible = "st,m41t0";
+		reg = <0x68>;
+		status = "disabled";
+	};
 };
 
 &lcdif {
+	assigned-clocks = <&clks IMX7D_LCDIF_PIXEL_ROOT_SRC>;
+	assigned-clock-parents = <&clks IMX7D_PLL_VIDEO_POST_DIV>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_lcdif_dat
 		     &pinctrl_lcdif_ctrl>;
+	status = "disabled";
+
+	port {
+		lcdif_out: endpoint {
+			remote-endpoint = <&lcd_panel_in>;
+		};
+	};
 };
 
+/* Colibri PWM<A> */
 &pwm1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm1>;
 };
 
+/* Colibri PWM<B> */
 &pwm2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm2>;
 };
 
+/* Colibri PWM<C> */
 &pwm3 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm3>;
 };
 
+/* Colibri PWM<D> */
 &pwm4 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm4>;
 };
 
 &reg_1p0d {
-	vin-supply = <&reg_DCDC3>;
+	vin-supply = <&reg_DCDC3>; /* VDDA_1P8_IN */
 };
 
 &sai1 {
@@ -430,237 +577,257 @@
 	status = "okay";
 };
 
+/* Colibri UART_A */
 &uart1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart1 &pinctrl_uart1_ctrl1 &pinctrl_uart1_ctrl2>;
 	assigned-clocks = <&clks IMX7D_UART1_ROOT_SRC>;
 	assigned-clock-parents = <&clks IMX7D_OSC_24M_CLK>;
-	uart-has-rtscts;
 	fsl,dte-mode;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1 &pinctrl_uart1_ctrl1 &pinctrl_uart1_ctrl2>;
+	uart-has-rtscts;
 };
 
+/* Colibri UART_B */
 &uart2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart2>;
 	assigned-clocks = <&clks IMX7D_UART2_ROOT_SRC>;
 	assigned-clock-parents = <&clks IMX7D_OSC_24M_CLK>;
-	uart-has-rtscts;
 	fsl,dte-mode;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	uart-has-rtscts;
 };
 
+/* Colibri UART_C */
 &uart3 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart3>;
 	assigned-clocks = <&clks IMX7D_UART3_ROOT_SRC>;
 	assigned-clock-parents = <&clks IMX7D_OSC_24M_CLK>;
 	fsl,dte-mode;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
 };
 
+/* Colibri USBC */
 &usbotg1 {
-	dr_mode = "host";
+	dr_mode = "otg";
+	extcon = <0>, <&extcon_usbc_det>;
 };
 
+/* Colibri MMC/SD */
 &usdhc1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_usdhc1 &pinctrl_cd_usdhc1>;
 	cd-gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
 	disable-wp;
+	no-1-8-v;
+	pinctrl-names = "default", "state_100mhz", "state_200mhz", "sleep";
+	pinctrl-0 = <&pinctrl_usdhc1 &pinctrl_cd_usdhc1>;
+	pinctrl-1 = <&pinctrl_usdhc1_100mhz &pinctrl_cd_usdhc1>;
+	pinctrl-2 = <&pinctrl_usdhc1_200mhz &pinctrl_cd_usdhc1>;
+	pinctrl-3 = <&pinctrl_usdhc1_sleep &pinctrl_cd_usdhc1_sleep>;
+	vmmc-supply = <&reg_3v3>;
 	vqmmc-supply = <&reg_LDO2>;
+	wakeup-source;
 };
 
+/* eMMC on 1GB (eMMC) SKUs */
 &usdhc3 {
-	pinctrl-names = "default", "state_100mhz", "state_200mhz";
-	pinctrl-0 = <&pinctrl_usdhc3>;
-	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
-	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
 	assigned-clocks = <&clks IMX7D_USDHC3_ROOT_CLK>;
 	assigned-clock-rates = <400000000>;
 	bus-width = <8>;
 	fsl,tuning-step = <2>;
-	vmmc-supply = <&reg_module_3v3>;
-	vqmmc-supply = <&reg_DCDC3>;
 	non-removable;
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
 	sdhci-caps-mask = <0x80000000 0x0>;
+	vmmc-supply = <&reg_module_3v3>;
+	vqmmc-supply = <&reg_DCDC3>;
 };
 
 &iomuxc {
 	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_gpio1 &pinctrl_gpio2 &pinctrl_gpio3 &pinctrl_gpio4
-		     &pinctrl_gpio7 &pinctrl_usbc_det>;
-
-	pinctrl_gpio1: gpio1-grp {
-		fsl,pins = <
-			MX7D_PAD_SAI1_RX_SYNC__GPIO6_IO16	0x14 /* SODIMM 77 */
-			MX7D_PAD_EPDC_DATA09__GPIO2_IO9		0x14 /* SODIMM 89 */
-			MX7D_PAD_EPDC_DATA08__GPIO2_IO8		0x74 /* SODIMM 91 */
-			MX7D_PAD_LCD_RESET__GPIO3_IO4		0x14 /* SODIMM 93 */
-			MX7D_PAD_EPDC_DATA13__GPIO2_IO13	0x14 /* SODIMM 95 */
-			MX7D_PAD_ENET1_RGMII_TXC__GPIO7_IO11	0x14 /* SODIMM 99 */
-			MX7D_PAD_EPDC_DATA10__GPIO2_IO10	0x74 /* SODIMM 105 */
-			MX7D_PAD_EPDC_DATA00__GPIO2_IO0		0x14 /* SODIMM 111 */
-			MX7D_PAD_EPDC_DATA01__GPIO2_IO1		0x14 /* SODIMM 113 */
-			MX7D_PAD_EPDC_DATA02__GPIO2_IO2		0x14 /* SODIMM 115 */
-			MX7D_PAD_EPDC_DATA03__GPIO2_IO3		0x14 /* SODIMM 117 */
-			MX7D_PAD_EPDC_DATA04__GPIO2_IO4		0x14 /* SODIMM 119 */
-			MX7D_PAD_EPDC_DATA05__GPIO2_IO5		0x14 /* SODIMM 121 */
-			MX7D_PAD_EPDC_DATA06__GPIO2_IO6		0x14 /* SODIMM 123 */
-			MX7D_PAD_EPDC_DATA07__GPIO2_IO7		0x14 /* SODIMM 125 */
-			MX7D_PAD_EPDC_SDCE2__GPIO2_IO22		0x14 /* SODIMM 127 */
-			MX7D_PAD_UART3_RTS_B__GPIO4_IO6		0x14 /* SODIMM 131 */
-			MX7D_PAD_EPDC_GDRL__GPIO2_IO26		0x14 /* SODIMM 133 */
-			MX7D_PAD_SAI1_RX_DATA__GPIO6_IO12	0x14 /* SODIMM 169 */
-			MX7D_PAD_SAI1_RX_BCLK__GPIO6_IO17	0x14 /* SODIMM 24 */
-			MX7D_PAD_SD2_DATA2__GPIO5_IO16		0x14 /* SODIMM 100 */
-			MX7D_PAD_SD2_DATA3__GPIO5_IO17		0x14 /* SODIMM 102 */
-			MX7D_PAD_EPDC_GDSP__GPIO2_IO27		0x14 /* SODIMM 104 */
-			MX7D_PAD_EPDC_BDR1__GPIO2_IO29		0x14 /* SODIMM 110 */
-			MX7D_PAD_EPDC_PWR_COM__GPIO2_IO30	0x14 /* SODIMM 112 */
-			MX7D_PAD_EPDC_SDCLK__GPIO2_IO16		0x14 /* SODIMM 114 */
-			MX7D_PAD_EPDC_SDLE__GPIO2_IO17		0x14 /* SODIMM 116 */
-			MX7D_PAD_EPDC_SDOE__GPIO2_IO18		0x14 /* SODIMM 118 */
-			MX7D_PAD_EPDC_SDSHR__GPIO2_IO19		0x14 /* SODIMM 120 */
-			MX7D_PAD_EPDC_SDCE0__GPIO2_IO20		0x14 /* SODIMM 122 */
-			MX7D_PAD_EPDC_SDCE1__GPIO2_IO21		0x14 /* SODIMM 124 */
-			MX7D_PAD_EPDC_DATA14__GPIO2_IO14	0x14 /* SODIMM 126 */
-			MX7D_PAD_EPDC_PWR_STAT__GPIO2_IO31	0x14 /* SODIMM 128 */
-			MX7D_PAD_EPDC_SDCE3__GPIO2_IO23		0x14 /* SODIMM 130 */
-			MX7D_PAD_EPDC_GDCLK__GPIO2_IO24		0x14 /* SODIMM 132 */
-			MX7D_PAD_EPDC_GDOE__GPIO2_IO25		0x14 /* SODIMM 134 */
-			MX7D_PAD_EPDC_DATA12__GPIO2_IO12	0x14 /* SODIMM 150 */
-			MX7D_PAD_EPDC_DATA11__GPIO2_IO11	0x14 /* SODIMM 152 */
-			MX7D_PAD_SD2_CLK__GPIO5_IO12		0x14 /* SODIMM 184 */
-			MX7D_PAD_SD2_CMD__GPIO5_IO13		0x14 /* SODIMM 186 */
-		>;
-	};
-
-	pinctrl_gpio2: gpio2-grp { /* On X22 Camera interface */
-		fsl,pins = <
-			MX7D_PAD_ECSPI2_SS0__GPIO4_IO23		0x14 /* SODIMM 65 */
-			MX7D_PAD_SD1_CD_B__GPIO5_IO0		0x74 /* SODIMM 69 */
-			MX7D_PAD_I2C4_SDA__GPIO4_IO15		0x14 /* SODIMM 75 */
-			MX7D_PAD_ECSPI1_MISO__GPIO4_IO18	0x14 /* SODIMM 79 */
-			MX7D_PAD_I2C3_SCL__GPIO4_IO12		0x14 /* SODIMM 81 */
-			MX7D_PAD_ECSPI2_MISO__GPIO4_IO22	0x14 /* SODIMM 85 */
-			MX7D_PAD_ECSPI1_SS0__GPIO4_IO19		0x14 /* SODIMM 97 */
-			MX7D_PAD_ECSPI1_SCLK__GPIO4_IO16	0x14 /* SODIMM 101 */
-			MX7D_PAD_ECSPI1_MOSI__GPIO4_IO17	0x14 /* SODIMM 103 */
-			MX7D_PAD_I2C3_SDA__GPIO4_IO13		0x14 /* SODIMM 94 */
-			MX7D_PAD_I2C4_SCL__GPIO4_IO14		0x14 /* SODIMM 96 */
-			MX7D_PAD_SD2_RESET_B__GPIO5_IO11	0x14 /* SODIMM 98 */
-		>;
-	};
-
-	pinctrl_gpio3: gpio3-grp { /* LCD 18-23 */
+	pinctrl-0 = <&pinctrl_gpio1 &pinctrl_gpio2 &pinctrl_gpio3 &pinctrl_gpio4>;
+
+	/*
+	 * Atmel MXT touchsceen + Capacitive Touch Adapter
+	 * NOTE: This pin group conflicts with pin groups pinctrl_pwm2/pinctrl_pwm3.
+	 * Don't use them simultaneously.
+	 */
+	pinctrl_atmel_adapter: atmelconnectorgrp {
 		fsl,pins = <
-			MX7D_PAD_LCD_DATA18__GPIO3_IO23		0x14 /* SODIMM 136 */
-			MX7D_PAD_LCD_DATA19__GPIO3_IO24		0x14 /* SODIMM 138 */
-			MX7D_PAD_LCD_DATA20__GPIO3_IO25		0x14 /* SODIMM 140 */
-			MX7D_PAD_LCD_DATA21__GPIO3_IO26		0x14 /* SODIMM 142 */
-			MX7D_PAD_LCD_DATA22__GPIO3_IO27		0x74 /* SODIMM 144 */
-			MX7D_PAD_LCD_DATA23__GPIO3_IO28		0x74 /* SODIMM 146 */
+			MX7D_PAD_GPIO1_IO09__GPIO1_IO9		0x74 /* SODIMM 28 / INT */
+			MX7D_PAD_GPIO1_IO10__GPIO1_IO10		0x14 /* SODIMM 30 / RST */
 		>;
 	};
 
-	pinctrl_gpio4: gpio4-grp { /* Alternatively CAN2 */
+	/* Atmel MXT touchsceen + boards with built-in Capacitive Touch Connector */
+	pinctrl_atmel_connector: atmeladaptergrp {
 		fsl,pins = <
-			MX7D_PAD_GPIO1_IO15__GPIO1_IO15		0x14 /* SODIMM 178 */
-			MX7D_PAD_GPIO1_IO14__GPIO1_IO14		0x14 /* SODIMM 188 */
+			MX7D_PAD_EPDC_BDR0__GPIO2_IO28		0x14 /* SODIMM 106 / RST */
+			MX7D_PAD_EPDC_DATA15__GPIO2_IO15	0x74 /* SODIMM 107 / INT */
 		>;
 	};
 
-	pinctrl_gpio7: gpio7-grp { /* Alternatively CAN1 */
+	pinctrl_can_int: canintgrp {
 		fsl,pins = <
-			MX7D_PAD_ENET1_RGMII_RD3__GPIO7_IO3	0x14 /* SODIMM 55 */
-			MX7D_PAD_ENET1_RGMII_RD2__GPIO7_IO2	0x14 /* SODIMM 63 */
+			MX7D_PAD_SD1_RESET_B__GPIO5_IO2		0X14 /* SODIMM 73 */
 		>;
 	};
 
-	pinctrl_i2c1_int: i2c1-int-grp { /* PMIC / TOUCH */
+	pinctrl_ecspi3: ecspi3grp {
 		fsl,pins = <
-			MX7D_PAD_GPIO1_IO13__GPIO1_IO13	0x79
+			MX7D_PAD_I2C1_SCL__ECSPI3_MISO		0x2 /* SODIMM 90 */
+			MX7D_PAD_I2C1_SDA__ECSPI3_MOSI		0x2 /* SODIMM 92 */
+			MX7D_PAD_I2C2_SCL__ECSPI3_SCLK		0x2 /* SODIMM 88 */
 		>;
 	};
 
-	pinctrl_can_int: can-int-grp {
+	pinctrl_ecspi3_cs: ecspi3csgrp {
 		fsl,pins = <
-			MX7D_PAD_SD1_RESET_B__GPIO5_IO2		0X14 /* SODIMM 73 */
+			MX7D_PAD_I2C2_SDA__GPIO4_IO11		0x14 /* SODIMM 86 */
 		>;
 	};
 
 	pinctrl_enet1: enet1grp {
 		fsl,pins = <
-			MX7D_PAD_ENET1_RGMII_RX_CTL__ENET1_RGMII_RX_CTL	0x73
 			MX7D_PAD_ENET1_RGMII_RD0__ENET1_RGMII_RD0	0x73
 			MX7D_PAD_ENET1_RGMII_RD1__ENET1_RGMII_RD1	0x73
 			MX7D_PAD_ENET1_RGMII_RXC__ENET1_RX_ER		0x73
-
-			MX7D_PAD_ENET1_RGMII_TX_CTL__ENET1_RGMII_TX_CTL	0x73
+			MX7D_PAD_ENET1_RGMII_RX_CTL__ENET1_RGMII_RX_CTL	0x73
 			MX7D_PAD_ENET1_RGMII_TD0__ENET1_RGMII_TD0	0x73
 			MX7D_PAD_ENET1_RGMII_TD1__ENET1_RGMII_TD1	0x73
+			MX7D_PAD_ENET1_RGMII_TX_CTL__ENET1_RGMII_TX_CTL	0x73
 			MX7D_PAD_GPIO1_IO12__CCM_ENET_REF_CLK1		0x73
 			MX7D_PAD_SD2_CD_B__ENET1_MDIO			0x3
 			MX7D_PAD_SD2_WP__ENET1_MDC			0x3
 		>;
 	};
 
-	pinctrl_enet1_sleep: enet1sleepgrp {
+	pinctrl_enet1_sleep: enet1-sleepgrp {
 		fsl,pins = <
-			MX7D_PAD_ENET1_RGMII_RX_CTL__GPIO7_IO4		0x0
 			MX7D_PAD_ENET1_RGMII_RD0__GPIO7_IO0		0x0
 			MX7D_PAD_ENET1_RGMII_RD1__GPIO7_IO1		0x0
 			MX7D_PAD_ENET1_RGMII_RXC__GPIO7_IO5		0x0
-
-			MX7D_PAD_ENET1_RGMII_TX_CTL__GPIO7_IO10		0x0
+			MX7D_PAD_ENET1_RGMII_RX_CTL__GPIO7_IO4		0x0
 			MX7D_PAD_ENET1_RGMII_TD0__GPIO7_IO6		0x0
 			MX7D_PAD_ENET1_RGMII_TD1__GPIO7_IO7		0x0
+			MX7D_PAD_ENET1_RGMII_TX_CTL__GPIO7_IO10		0x0
 			MX7D_PAD_GPIO1_IO12__GPIO1_IO12			0x0
 			MX7D_PAD_SD2_CD_B__GPIO5_IO9			0x0
 			MX7D_PAD_SD2_WP__GPIO5_IO10			0x0
 		>;
 	};
 
-	pinctrl_ecspi3_cs: ecspi3-cs-grp {
+	pinctrl_flexcan1: flexcan1grp {
 		fsl,pins = <
-			MX7D_PAD_I2C2_SDA__GPIO4_IO11		0x14
+			MX7D_PAD_ENET1_RGMII_RD2__FLEXCAN1_RX	0x79 /* SODIMM 63 */
+			MX7D_PAD_ENET1_RGMII_RD3__FLEXCAN1_TX	0x79 /* SODIMM 55 */
 		>;
 	};
 
-	pinctrl_ecspi3: ecspi3-grp {
+	pinctrl_flexcan2: flexcan2grp {
 		fsl,pins = <
-			MX7D_PAD_I2C1_SCL__ECSPI3_MISO		0x2
-			MX7D_PAD_I2C1_SDA__ECSPI3_MOSI		0x2
-			MX7D_PAD_I2C2_SCL__ECSPI3_SCLK		0x2
+			MX7D_PAD_GPIO1_IO14__FLEXCAN2_RX	0x79 /* SODIMM 188 */
+			MX7D_PAD_GPIO1_IO15__FLEXCAN2_TX	0x79 /* SODIMM 178 */
 		>;
 	};
 
-	pinctrl_flexcan1: flexcan1-grp {
+	pinctrl_gpio1: gpio1grp {
 		fsl,pins = <
-			MX7D_PAD_ENET1_RGMII_RD3__FLEXCAN1_TX	0x79 /* SODIMM 55 */
-			MX7D_PAD_ENET1_RGMII_RD2__FLEXCAN1_RX	0x79 /* SODIMM 63 */
+			MX7D_PAD_EPDC_BDR1__GPIO2_IO29		0x14 /* SODIMM 110 */
+			MX7D_PAD_EPDC_DATA00__GPIO2_IO0		0x14 /* SODIMM 111 */
+			MX7D_PAD_EPDC_DATA01__GPIO2_IO1		0x14 /* SODIMM 113 */
+			MX7D_PAD_EPDC_DATA02__GPIO2_IO2		0x14 /* SODIMM 115 */
+			MX7D_PAD_EPDC_DATA03__GPIO2_IO3		0x14 /* SODIMM 117 */
+			MX7D_PAD_EPDC_DATA04__GPIO2_IO4		0x14 /* SODIMM 119 */
+			MX7D_PAD_EPDC_DATA05__GPIO2_IO5		0x14 /* SODIMM 121 */
+			MX7D_PAD_EPDC_DATA06__GPIO2_IO6		0x14 /* SODIMM 123 */
+			MX7D_PAD_EPDC_DATA07__GPIO2_IO7		0x14 /* SODIMM 125 */
+			MX7D_PAD_EPDC_DATA08__GPIO2_IO8		0x74 /* SODIMM 91 */
+			MX7D_PAD_EPDC_DATA09__GPIO2_IO9		0x14 /* SODIMM 89 */
+			MX7D_PAD_EPDC_DATA10__GPIO2_IO10	0x74 /* SODIMM 105 */
+			MX7D_PAD_EPDC_DATA11__GPIO2_IO11	0x14 /* SODIMM 152 */
+			MX7D_PAD_EPDC_DATA12__GPIO2_IO12	0x14 /* SODIMM 150 */
+			MX7D_PAD_EPDC_DATA14__GPIO2_IO14	0x14 /* SODIMM 126 */
+			MX7D_PAD_EPDC_GDCLK__GPIO2_IO24		0x14 /* SODIMM 132 */
+			MX7D_PAD_EPDC_GDOE__GPIO2_IO25		0x14 /* SODIMM 134 */
+			MX7D_PAD_EPDC_GDRL__GPIO2_IO26		0x14 /* SODIMM 133 */
+			MX7D_PAD_EPDC_GDSP__GPIO2_IO27		0x14 /* SODIMM 104 */
+			MX7D_PAD_EPDC_PWR_COM__GPIO2_IO30	0x14 /* SODIMM 112 */
+			MX7D_PAD_EPDC_PWR_STAT__GPIO2_IO31	0x14 /* SODIMM 128 */
+			MX7D_PAD_EPDC_SDCE0__GPIO2_IO20		0x14 /* SODIMM 122 */
+			MX7D_PAD_EPDC_SDCE1__GPIO2_IO21		0x14 /* SODIMM 124 */
+			MX7D_PAD_EPDC_SDCE2__GPIO2_IO22		0x14 /* SODIMM 127 */
+			MX7D_PAD_EPDC_SDCE3__GPIO2_IO23		0x14 /* SODIMM 130 */
+			MX7D_PAD_EPDC_SDCLK__GPIO2_IO16		0x14 /* SODIMM 114 */
+			MX7D_PAD_EPDC_SDLE__GPIO2_IO17		0x14 /* SODIMM 116 */
+			MX7D_PAD_EPDC_SDOE__GPIO2_IO18		0x14 /* SODIMM 118 */
+			MX7D_PAD_EPDC_SDSHR__GPIO2_IO19		0x14 /* SODIMM 120 */
+			MX7D_PAD_LCD_RESET__GPIO3_IO4		0x14 /* SODIMM 93 */
+			MX7D_PAD_SAI1_RX_BCLK__GPIO6_IO17	0x14 /* SODIMM 24 */
+			MX7D_PAD_SAI1_RX_DATA__GPIO6_IO12	0x14 /* SODIMM 169 */
+			MX7D_PAD_SAI1_RX_SYNC__GPIO6_IO16	0x14 /* SODIMM 77 */
+			MX7D_PAD_SD2_CLK__GPIO5_IO12		0x14 /* SODIMM 184 */
+			MX7D_PAD_SD2_CMD__GPIO5_IO13		0x14 /* SODIMM 186 */
+			MX7D_PAD_SD2_DATA2__GPIO5_IO16		0x14 /* SODIMM 100 */
+			MX7D_PAD_SD2_DATA3__GPIO5_IO17		0x14 /* SODIMM 102 */
+			MX7D_PAD_UART3_RTS_B__GPIO4_IO6		0x14 /* SODIMM 131 */
 		>;
 	};
 
-	pinctrl_flexcan2: flexcan2-grp {
+	pinctrl_gpio2: gpio2grp { /* On X22 Camera interface */
 		fsl,pins = <
-			MX7D_PAD_GPIO1_IO14__FLEXCAN2_RX	0x79 /* SODIMM 188 */
-			MX7D_PAD_GPIO1_IO15__FLEXCAN2_TX	0x79 /* SODIMM 178 */
+			MX7D_PAD_ECSPI1_MISO__GPIO4_IO18	0x14 /* SODIMM 79 */
+			MX7D_PAD_ECSPI1_MOSI__GPIO4_IO17	0x14 /* SODIMM 103 */
+			MX7D_PAD_ECSPI1_SCLK__GPIO4_IO16	0x14 /* SODIMM 101 */
+			MX7D_PAD_ECSPI1_SS0__GPIO4_IO19		0x14 /* SODIMM 97 */
+			MX7D_PAD_ECSPI2_MISO__GPIO4_IO22	0x14 /* SODIMM 85 */
+			MX7D_PAD_ECSPI2_SS0__GPIO4_IO23		0x14 /* SODIMM 65 */
+			MX7D_PAD_I2C3_SCL__GPIO4_IO12		0x14 /* SODIMM 81 */
+			MX7D_PAD_I2C3_SDA__GPIO4_IO13		0x14 /* SODIMM 94 */
+			MX7D_PAD_I2C4_SCL__GPIO4_IO14		0x14 /* SODIMM 96 */
+			MX7D_PAD_I2C4_SDA__GPIO4_IO15		0x14 /* SODIMM 75 */
+			MX7D_PAD_SD1_CD_B__GPIO5_IO0		0x74 /* SODIMM 69 */
+			MX7D_PAD_SD2_RESET_B__GPIO5_IO11	0x14 /* SODIMM 98 */
+		>;
+	};
+
+	pinctrl_gpio3: gpio3grp { /* LCD 18-23 */
+		fsl,pins = <
+			MX7D_PAD_LCD_DATA18__GPIO3_IO23		0x14 /* SODIMM 136 */
+			MX7D_PAD_LCD_DATA19__GPIO3_IO24		0x14 /* SODIMM 138 */
+			MX7D_PAD_LCD_DATA20__GPIO3_IO25		0x14 /* SODIMM 140 */
+			MX7D_PAD_LCD_DATA21__GPIO3_IO26		0x14 /* SODIMM 142 */
+			MX7D_PAD_LCD_DATA22__GPIO3_IO27		0x74 /* SODIMM 144 */
+			MX7D_PAD_LCD_DATA23__GPIO3_IO28		0x74 /* SODIMM 146 */
+		>;
+	};
+
+	pinctrl_gpio4: gpio4grp { /* Alternatively CAN2 */
+		fsl,pins = <
+			MX7D_PAD_GPIO1_IO14__GPIO1_IO14		0x14 /* SODIMM 188 */
+			MX7D_PAD_GPIO1_IO15__GPIO1_IO15		0x14 /* SODIMM 178 */
+		>;
+	};
+
+	pinctrl_gpio7: gpio7grp { /* Alternatively CAN1 */
+		fsl,pins = <
+			MX7D_PAD_ENET1_RGMII_RD2__GPIO7_IO2	0x14 /* SODIMM 63 */
+			MX7D_PAD_ENET1_RGMII_RD3__GPIO7_IO3	0x14 /* SODIMM 55 */
 		>;
 	};
 
-	pinctrl_gpio_bl_on: gpio-bl-on {
+	pinctrl_gpio_bl_on: gpioblongrp {
 		fsl,pins = <
 			MX7D_PAD_SD1_WP__GPIO5_IO1		0x14 /* SODIMM 71 */
 		>;
 	};
 
-	pinctrl_gpmi_nand: gpmi-nand-grp {
+	pinctrl_gpmi_nand: gpminandgrp {
 		fsl,pins = <
-			MX7D_PAD_SD3_CLK__NAND_CLE		0x71
-			MX7D_PAD_SD3_CMD__NAND_ALE		0x71
 			MX7D_PAD_SAI1_TX_BCLK__NAND_CE0_B	0x71
 			MX7D_PAD_SAI1_TX_DATA__NAND_READY_B	0x74
-			MX7D_PAD_SD3_STROBE__NAND_RE_B		0x71
-			MX7D_PAD_SD3_RESET_B__NAND_WE_B		0x71
+			MX7D_PAD_SD3_CLK__NAND_CLE		0x71
+			MX7D_PAD_SD3_CMD__NAND_ALE		0x71
 			MX7D_PAD_SD3_DATA0__NAND_DATA00		0x71
 			MX7D_PAD_SD3_DATA1__NAND_DATA01		0x71
 			MX7D_PAD_SD3_DATA2__NAND_DATA02		0x71
@@ -669,13 +836,21 @@
 			MX7D_PAD_SD3_DATA5__NAND_DATA05		0x71
 			MX7D_PAD_SD3_DATA6__NAND_DATA06		0x71
 			MX7D_PAD_SD3_DATA7__NAND_DATA07		0x71
+			MX7D_PAD_SD3_RESET_B__NAND_WE_B		0x71
+			MX7D_PAD_SD3_STROBE__NAND_RE_B		0x71
 		>;
 	};
 
-	pinctrl_i2c4: i2c4-grp {
+	pinctrl_i2c1_int: i2c1intgrp { /* PMIC / TOUCH */
 		fsl,pins = <
-			MX7D_PAD_ENET1_RGMII_TD3__I2C4_SDA	0x4000007f
-			MX7D_PAD_ENET1_RGMII_TD2__I2C4_SCL	0x4000007f
+			MX7D_PAD_GPIO1_IO13__GPIO1_IO13	0x79
+		>;
+	};
+
+	pinctrl_i2c4: i2c4grp {
+		fsl,pins = <
+			MX7D_PAD_ENET1_RGMII_TD2__I2C4_SCL	0x4000007f /* SODIMM 196 */
+			MX7D_PAD_ENET1_RGMII_TD3__I2C4_SDA	0x4000007f /* SODIMM 194 */
 		>;
 	};
 
@@ -686,155 +861,176 @@
 		>;
 	};
 
-	pinctrl_lcdif_dat: lcdif-dat-grp {
+	pinctrl_lcdif_dat: lcdifdatgrp {
+		fsl,pins = <
+			MX7D_PAD_LCD_DATA00__LCD_DATA0		0x79 /* SODIMM 76 */
+			MX7D_PAD_LCD_DATA01__LCD_DATA1		0x79 /* SODIMM 70 */
+			MX7D_PAD_LCD_DATA02__LCD_DATA2		0x79 /* SODIMM 60 */
+			MX7D_PAD_LCD_DATA03__LCD_DATA3		0x79 /* SODIMM 58 */
+			MX7D_PAD_LCD_DATA04__LCD_DATA4		0x79 /* SODIMM 78 */
+			MX7D_PAD_LCD_DATA05__LCD_DATA5		0x79 /* SODIMM 72 */
+			MX7D_PAD_LCD_DATA06__LCD_DATA6		0x79 /* SODIMM 80 */
+			MX7D_PAD_LCD_DATA07__LCD_DATA7		0x79 /* SODIMM 46 */
+			MX7D_PAD_LCD_DATA08__LCD_DATA8		0x79 /* SODIMM 62 */
+			MX7D_PAD_LCD_DATA09__LCD_DATA9		0x79 /* SODIMM 48 */
+			MX7D_PAD_LCD_DATA10__LCD_DATA10		0x79 /* SODIMM 74 */
+			MX7D_PAD_LCD_DATA11__LCD_DATA11		0x79 /* SODIMM 50 */
+			MX7D_PAD_LCD_DATA12__LCD_DATA12		0x79 /* SODIMM 52 */
+			MX7D_PAD_LCD_DATA13__LCD_DATA13		0x79 /* SODIMM 54 */
+			MX7D_PAD_LCD_DATA14__LCD_DATA14		0x79 /* SODIMM 66 */
+			MX7D_PAD_LCD_DATA15__LCD_DATA15		0x79 /* SODIMM 64 */
+			MX7D_PAD_LCD_DATA16__LCD_DATA16		0x79 /* SODIMM 57 */
+			MX7D_PAD_LCD_DATA17__LCD_DATA17		0x79 /* SODIMM 61 */
+		>;
+	};
+
+	pinctrl_lcdif_dat_24: lcdifdat24grp {
 		fsl,pins = <
-			MX7D_PAD_LCD_DATA00__LCD_DATA0		0x79
-			MX7D_PAD_LCD_DATA01__LCD_DATA1		0x79
-			MX7D_PAD_LCD_DATA02__LCD_DATA2		0x79
-			MX7D_PAD_LCD_DATA03__LCD_DATA3		0x79
-			MX7D_PAD_LCD_DATA04__LCD_DATA4		0x79
-			MX7D_PAD_LCD_DATA05__LCD_DATA5		0x79
-			MX7D_PAD_LCD_DATA06__LCD_DATA6		0x79
-			MX7D_PAD_LCD_DATA07__LCD_DATA7		0x79
-			MX7D_PAD_LCD_DATA08__LCD_DATA8		0x79
-			MX7D_PAD_LCD_DATA09__LCD_DATA9		0x79
-			MX7D_PAD_LCD_DATA10__LCD_DATA10		0x79
-			MX7D_PAD_LCD_DATA11__LCD_DATA11		0x79
-			MX7D_PAD_LCD_DATA12__LCD_DATA12		0x79
-			MX7D_PAD_LCD_DATA13__LCD_DATA13		0x79
-			MX7D_PAD_LCD_DATA14__LCD_DATA14		0x79
-			MX7D_PAD_LCD_DATA15__LCD_DATA15		0x79
-			MX7D_PAD_LCD_DATA16__LCD_DATA16		0x79
-			MX7D_PAD_LCD_DATA17__LCD_DATA17		0x79
+			MX7D_PAD_LCD_DATA18__LCD_DATA18		0x79 /* SODIMM 136 */
+			MX7D_PAD_LCD_DATA19__LCD_DATA19		0x79 /* SODIMM 138 */
+			MX7D_PAD_LCD_DATA20__LCD_DATA20		0x79 /* SODIMM 140 */
+			MX7D_PAD_LCD_DATA21__LCD_DATA21		0x79 /* SODIMM 142 */
+			MX7D_PAD_LCD_DATA22__LCD_DATA22		0x79 /* SODIMM 144 */
+			MX7D_PAD_LCD_DATA23__LCD_DATA23		0x79 /* SODIMM 146 */
 		>;
 	};
 
-	pinctrl_lcdif_dat_24: lcdif-dat-24-grp {
+	pinctrl_lcdif_ctrl: lcdifctrlgrp {
 		fsl,pins = <
-			MX7D_PAD_LCD_DATA18__LCD_DATA18		0x79
-			MX7D_PAD_LCD_DATA19__LCD_DATA19		0x79
-			MX7D_PAD_LCD_DATA20__LCD_DATA20		0x79
-			MX7D_PAD_LCD_DATA21__LCD_DATA21		0x79
-			MX7D_PAD_LCD_DATA22__LCD_DATA22		0x79
-			MX7D_PAD_LCD_DATA23__LCD_DATA23		0x79
+			MX7D_PAD_LCD_CLK__LCD_CLK		0x79 /* SODIMM 56 */
+			MX7D_PAD_LCD_ENABLE__LCD_ENABLE		0x79 /* SODIMM 44 */
+			MX7D_PAD_LCD_HSYNC__LCD_HSYNC		0x79 /* SODIMM 68 */
+			MX7D_PAD_LCD_VSYNC__LCD_VSYNC		0x79 /* SODIMM 82 */
 		>;
 	};
 
-	pinctrl_lcdif_ctrl: lcdif-ctrl-grp {
+	pinctrl_lvds_transceiver: lvdstx {
 		fsl,pins = <
-			MX7D_PAD_LCD_CLK__LCD_CLK		0x79
-			MX7D_PAD_LCD_ENABLE__LCD_ENABLE		0x79
-			MX7D_PAD_LCD_VSYNC__LCD_VSYNC		0x79
-			MX7D_PAD_LCD_HSYNC__LCD_HSYNC		0x79
+			MX7D_PAD_ENET1_RGMII_RD2__GPIO7_IO2     0x14 /* SODIMM 63 */
+			MX7D_PAD_ENET1_RGMII_RD3__GPIO7_IO3     0x74 /* SODIMM 55 */
+			MX7D_PAD_ENET1_RGMII_TXC__GPIO7_IO11    0x14 /* SODIMM 99 */
+			MX7D_PAD_EPDC_DATA13__GPIO2_IO13        0x14 /* SODIMM 95 */
 		>;
 	};
 
-	pinctrl_pwm1: pwm1-grp {
+	pinctrl_pwm1: pwm1grp {
 		fsl,pins = <
-			MX7D_PAD_GPIO1_IO08__PWM1_OUT		0x79
-			MX7D_PAD_ECSPI2_MOSI__GPIO4_IO21	0x4
+			MX7D_PAD_ECSPI2_MOSI__GPIO4_IO21	0x4  /* SODIMM 59 */
+			MX7D_PAD_GPIO1_IO08__PWM1_OUT		0x79 /* SODIMM 59 */
 		>;
 	};
 
-	pinctrl_pwm2: pwm2-grp {
+	pinctrl_pwm2: pwm2grp {
 		fsl,pins = <
-			MX7D_PAD_GPIO1_IO09__PWM2_OUT		0x79
+			MX7D_PAD_GPIO1_IO09__PWM2_OUT		0x79 /* SODIMM 28 */
 		>;
 	};
 
-	pinctrl_pwm3: pwm3-grp {
+	pinctrl_pwm3: pwm3grp {
 		fsl,pins = <
-			MX7D_PAD_GPIO1_IO10__PWM3_OUT		0x79
+			MX7D_PAD_GPIO1_IO10__PWM3_OUT		0x79 /* SODIMM 30 */
 		>;
 	};
 
-	pinctrl_pwm4: pwm4-grp {
+	pinctrl_pwm4: pwm4grp {
 		fsl,pins = <
-			MX7D_PAD_GPIO1_IO11__PWM4_OUT		0x79
-			MX7D_PAD_ECSPI2_SCLK__GPIO4_IO20	0x4
+			MX7D_PAD_ECSPI2_SCLK__GPIO4_IO20	0x4  /* SODIMM 67 */
+			MX7D_PAD_GPIO1_IO11__PWM4_OUT		0x79 /* SODIMM 67 */
 		>;
 	};
 
-	pinctrl_uart1: uart1-grp {
+	pinctrl_uart1: uart1grp {
 		fsl,pins = <
-			MX7D_PAD_UART1_TX_DATA__UART1_DTE_RX	0x79
-			MX7D_PAD_UART1_RX_DATA__UART1_DTE_TX	0x79
-			MX7D_PAD_SAI2_TX_BCLK__UART1_DTE_CTS	0x79
-			MX7D_PAD_SAI2_TX_SYNC__UART1_DTE_RTS	0x79
+			MX7D_PAD_SAI2_TX_BCLK__UART1_DTE_CTS	0x79 /* SODIMM 25 */
+			MX7D_PAD_SAI2_TX_SYNC__UART1_DTE_RTS	0x79 /* SODIMM 27 */
+			MX7D_PAD_UART1_RX_DATA__UART1_DTE_TX	0x79 /* SODIMM 35 */
+			MX7D_PAD_UART1_TX_DATA__UART1_DTE_RX	0x79 /* SODIMM 33 */
 		>;
 	};
 
-	pinctrl_uart1_ctrl1: uart1-ctrl1-grp {
+	pinctrl_uart1_ctrl1: uart1ctrl1grp {
 		fsl,pins = <
-			MX7D_PAD_SD2_DATA1__GPIO5_IO15		0x14 /* DCD */
-			MX7D_PAD_SD2_DATA0__GPIO5_IO14		0x14 /* DTR */
+			MX7D_PAD_SD2_DATA0__GPIO5_IO14		0x14 /* SODIMM 23 / DTR */
+			MX7D_PAD_SD2_DATA1__GPIO5_IO15		0x14 /* SODIMM 31 / DCD */
 		>;
 	};
 
-	pinctrl_uart2: uart2-grp {
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX7D_PAD_SAI2_RX_DATA__UART2_DTE_RTS	0x79 /* SODIMM 32 / CTS */
+			MX7D_PAD_SAI2_TX_DATA__UART2_DTE_CTS	0x79 /* SODIMM 34 / RTS */
+			MX7D_PAD_UART2_RX_DATA__UART2_DTE_TX	0x79 /* SODIMM 38 */
+			MX7D_PAD_UART2_TX_DATA__UART2_DTE_RX	0x79 /* SODIMM 36 */
+		>;
+	};
+	pinctrl_uart3: uart3grp {
 		fsl,pins = <
-			MX7D_PAD_UART2_TX_DATA__UART2_DTE_RX 0x79
-			MX7D_PAD_UART2_RX_DATA__UART2_DTE_TX 0x79
-			MX7D_PAD_SAI2_RX_DATA__UART2_DTE_RTS 0x79
-			MX7D_PAD_SAI2_TX_DATA__UART2_DTE_CTS 0x79
+			MX7D_PAD_UART3_RX_DATA__UART3_DTE_TX	0x79 /* SODIMM 21 */
+			MX7D_PAD_UART3_TX_DATA__UART3_DTE_RX	0x79 /* SODIMM 19 */
 		>;
 	};
-	pinctrl_uart3: uart3-grp {
+
+	pinctrl_usbc_det: usbcdetgrp {
 		fsl,pins = <
-			MX7D_PAD_UART3_TX_DATA__UART3_DTE_RX 0x79
-			MX7D_PAD_UART3_RX_DATA__UART3_DTE_TX 0x79
+			MX7D_PAD_ENET1_CRS__GPIO7_IO14		0x14 /* SODIMM 137 / USBC_DET */
 		>;
 	};
 
-	pinctrl_usbc_det: gpio-usbc-det {
+	pinctrl_usbh_reg: usbhreggrp {
 		fsl,pins = <
-			MX7D_PAD_ENET1_CRS__GPIO7_IO14	0x14
+			MX7D_PAD_UART3_CTS_B__GPIO4_IO7		0x14 /* SODIMM 129 / USBH_PEN */
 		>;
 	};
 
-	pinctrl_usbh_reg: gpio-usbh-vbus {
+	pinctrl_usdhc1: usdhc1grp {
 		fsl,pins = <
-			MX7D_PAD_UART3_CTS_B__GPIO4_IO7	0x14 /* SODIMM 129 USBH PEN */
+			MX7D_PAD_SD1_CLK__SD1_CLK		0x19 /* SODIMM 47 */
+			MX7D_PAD_SD1_CMD__SD1_CMD		0x59 /* SODIMM 190 */
+			MX7D_PAD_SD1_DATA0__SD1_DATA0		0x59 /* SODIMM 192 */
+			MX7D_PAD_SD1_DATA1__SD1_DATA1		0x59 /* SODIMM 49 */
+			MX7D_PAD_SD1_DATA2__SD1_DATA2		0x59 /* SODIMM 51 */
+			MX7D_PAD_SD1_DATA3__SD1_DATA3		0x59 /* SODIMM 53 */
 		>;
 	};
 
-	pinctrl_usdhc1: usdhc1-grp {
+	pinctrl_usdhc1_100mhz: usdhc1-100mhzgrp {
 		fsl,pins = <
-			MX7D_PAD_SD1_CMD__SD1_CMD	0x59
-			MX7D_PAD_SD1_CLK__SD1_CLK	0x19
-			MX7D_PAD_SD1_DATA0__SD1_DATA0	0x59
-			MX7D_PAD_SD1_DATA1__SD1_DATA1	0x59
-			MX7D_PAD_SD1_DATA2__SD1_DATA2	0x59
-			MX7D_PAD_SD1_DATA3__SD1_DATA3	0x59
+			MX7D_PAD_SD1_CLK__SD1_CLK		0x1a
+			MX7D_PAD_SD1_CMD__SD1_CMD		0x5a
+			MX7D_PAD_SD1_DATA0__SD1_DATA0		0x5a
+			MX7D_PAD_SD1_DATA1__SD1_DATA1		0x5a
+			MX7D_PAD_SD1_DATA2__SD1_DATA2		0x5a
+			MX7D_PAD_SD1_DATA3__SD1_DATA3		0x5a
 		>;
 	};
 
-	pinctrl_usdhc1_100mhz: usdhc1grp_100mhz {
+	pinctrl_usdhc1_200mhz: usdhc1-200mhzgrp {
 		fsl,pins = <
-			MX7D_PAD_SD1_CMD__SD1_CMD	0x5a
-			MX7D_PAD_SD1_CLK__SD1_CLK	0x1a
-			MX7D_PAD_SD1_DATA0__SD1_DATA0	0x5a
-			MX7D_PAD_SD1_DATA1__SD1_DATA1	0x5a
-			MX7D_PAD_SD1_DATA2__SD1_DATA2	0x5a
-			MX7D_PAD_SD1_DATA3__SD1_DATA3	0x5a
+			MX7D_PAD_SD1_CLK__SD1_CLK		0x1b
+			MX7D_PAD_SD1_CMD__SD1_CMD		0x5b
+			MX7D_PAD_SD1_DATA0__SD1_DATA0		0x5b
+			MX7D_PAD_SD1_DATA1__SD1_DATA1		0x5b
+			MX7D_PAD_SD1_DATA2__SD1_DATA2		0x5b
+			MX7D_PAD_SD1_DATA3__SD1_DATA3		0x5b
 		>;
 	};
 
-	pinctrl_usdhc1_200mhz: usdhc1grp_200mhz {
+	/* Avoid backfeeding with removed card power. */
+	pinctrl_usdhc1_sleep: usdhc1-slpgrp {
 		fsl,pins = <
-			MX7D_PAD_SD1_CMD__SD1_CMD	0x5b
-			MX7D_PAD_SD1_CLK__SD1_CLK	0x1b
-			MX7D_PAD_SD1_DATA0__SD1_DATA0	0x5b
-			MX7D_PAD_SD1_DATA1__SD1_DATA1	0x5b
-			MX7D_PAD_SD1_DATA2__SD1_DATA2	0x5b
-			MX7D_PAD_SD1_DATA3__SD1_DATA3	0x5b
+			MX7D_PAD_SD1_CMD__SD1_CMD		0x10
+			MX7D_PAD_SD1_CLK__SD1_CLK		0x10
+			MX7D_PAD_SD1_DATA0__SD1_DATA0		0x10
+			MX7D_PAD_SD1_DATA1__SD1_DATA1		0x10
+			MX7D_PAD_SD1_DATA2__SD1_DATA2		0x10
+			MX7D_PAD_SD1_DATA3__SD1_DATA3		0x10
 		>;
 	};
 
 	pinctrl_usdhc3: usdhc3grp {
 		fsl,pins = <
-			MX7D_PAD_SD3_CMD__SD3_CMD		0x59
 			MX7D_PAD_SD3_CLK__SD3_CLK		0x19
+			MX7D_PAD_SD3_CMD__SD3_CMD		0x59
 			MX7D_PAD_SD3_DATA0__SD3_DATA0		0x59
 			MX7D_PAD_SD3_DATA1__SD3_DATA1		0x59
 			MX7D_PAD_SD3_DATA2__SD3_DATA2		0x59
@@ -847,10 +1043,10 @@
 		>;
 	};
 
-	pinctrl_usdhc3_100mhz: usdhc3grp_100mhz {
+	pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
 		fsl,pins = <
-			MX7D_PAD_SD3_CMD__SD3_CMD		0x5a
 			MX7D_PAD_SD3_CLK__SD3_CLK		0x1a
+			MX7D_PAD_SD3_CMD__SD3_CMD		0x5a
 			MX7D_PAD_SD3_DATA0__SD3_DATA0		0x5a
 			MX7D_PAD_SD3_DATA1__SD3_DATA1		0x5a
 			MX7D_PAD_SD3_DATA2__SD3_DATA2		0x5a
@@ -863,10 +1059,10 @@
 		>;
 	};
 
-	pinctrl_usdhc3_200mhz: usdhc3grp_200mhz {
+	pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
 		fsl,pins = <
-			MX7D_PAD_SD3_CMD__SD3_CMD		0x5b
 			MX7D_PAD_SD3_CLK__SD3_CLK		0x1b
+			MX7D_PAD_SD3_CMD__SD3_CMD		0x5b
 			MX7D_PAD_SD3_DATA0__SD3_DATA0		0x5b
 			MX7D_PAD_SD3_DATA1__SD3_DATA1		0x5b
 			MX7D_PAD_SD3_DATA2__SD3_DATA2		0x5b
@@ -879,16 +1075,16 @@
 		>;
 	};
 
-	pinctrl_sai1: sai1-grp {
+	pinctrl_sai1: sai1grp {
 		fsl,pins = <
-			MX7D_PAD_ENET1_RX_CLK__SAI1_TX_BCLK     0x1f
-			MX7D_PAD_SAI1_TX_SYNC__SAI1_TX_SYNC	0x1f
 			MX7D_PAD_ENET1_COL__SAI1_TX_DATA0	0x30
+			MX7D_PAD_ENET1_RX_CLK__SAI1_TX_BCLK     0x1f
 			MX7D_PAD_ENET1_TX_CLK__SAI1_RX_DATA0	0x1f
+			MX7D_PAD_SAI1_TX_SYNC__SAI1_TX_SYNC	0x1f
 		>;
 	};
 
-	pinctrl_sai1_mclk: sai1grp_mclk {
+	pinctrl_sai1_mclk: sai1mclkgrp {
 		fsl,pins = <
 			MX7D_PAD_SAI1_MCLK__SAI1_MCLK           0x1f
 		>;
@@ -899,23 +1095,35 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_gpio_lpsr>;
 
-	pinctrl_gpio_lpsr: gpio1-grp {
+	pinctrl_cd_usdhc1: cdusdhc1grp {
 		fsl,pins = <
-			MX7D_PAD_LPSR_GPIO1_IO02__GPIO1_IO2	0x59
-			MX7D_PAD_LPSR_GPIO1_IO03__GPIO1_IO3	0x59
+			MX7D_PAD_LPSR_GPIO1_IO00__GPIO1_IO0	0x59 /* SODIMM 43 / MMC_CD */
+		>;
+	};
+
+	pinctrl_cd_usdhc1_sleep: cdusdhc1-slpgrp {
+		fsl,pins = <
+			MX7D_PAD_LPSR_GPIO1_IO00__GPIO1_IO0	0x0
+		>;
+	};
+
+	pinctrl_gpio_lpsr: gpiolpsrgrp {
+		fsl,pins = <
+			MX7D_PAD_LPSR_GPIO1_IO02__GPIO1_IO2	0x59 /* SODIMM 135 */
+			MX7D_PAD_LPSR_GPIO1_IO03__GPIO1_IO3	0x59 /* SODIMM 22 */
 		>;
 	};
 
 	pinctrl_gpiokeys: gpiokeysgrp {
 		fsl,pins = <
-			MX7D_PAD_LPSR_GPIO1_IO01__GPIO1_IO1	0x19
+			MX7D_PAD_LPSR_GPIO1_IO01__GPIO1_IO1	0x19 /* SODIMM 45 / WAKE_UP */
 		>;
 	};
 
-	pinctrl_i2c1: i2c1-grp {
+	pinctrl_i2c1: i2c1grp {
 		fsl,pins = <
-			MX7D_PAD_LPSR_GPIO1_IO05__I2C1_SDA	0x4000007f
 			MX7D_PAD_LPSR_GPIO1_IO04__I2C1_SCL	0x4000007f
+			MX7D_PAD_LPSR_GPIO1_IO05__I2C1_SDA	0x4000007f
 		>;
 	};
 
@@ -926,16 +1134,10 @@
 		>;
 	};
 
-	pinctrl_cd_usdhc1: usdhc1-cd-grp {
-		fsl,pins = <
-			MX7D_PAD_LPSR_GPIO1_IO00__GPIO1_IO0	0x59 /* CD */
-		>;
-	};
-
-	pinctrl_uart1_ctrl2: uart1-ctrl2-grp {
+	pinctrl_uart1_ctrl2: uart1ctrl2grp {
 		fsl,pins = <
-			MX7D_PAD_LPSR_GPIO1_IO07__GPIO1_IO7	0x14 /* DSR */
-			MX7D_PAD_LPSR_GPIO1_IO06__GPIO1_IO6	0x14 /* RI */
+			MX7D_PAD_LPSR_GPIO1_IO06__GPIO1_IO6	0x14 /* SODIMM 37 / RI */
+			MX7D_PAD_LPSR_GPIO1_IO07__GPIO1_IO7	0x14 /* SODIMM 29 / DSR */
 		>;
 	};
 };
diff --git a/arch/arm/boot/dts/imx7-mba7.dtsi b/arch/arm/boot/dts/imx7-mba7.dtsi
index 49086c6b6a0a..3df6dff7734a 100644
--- a/arch/arm/boot/dts/imx7-mba7.dtsi
+++ b/arch/arm/boot/dts/imx7-mba7.dtsi
@@ -302,7 +302,7 @@
 	tlv320aic32x4: audio-codec@18 {
 		compatible = "ti,tlv320aic32x4";
 		reg = <0x18>;
-		clocks = <&clks IMX7D_AUDIO_MCLK_ROOT_CLK>;
+		clocks = <&clks IMX7D_AUDIO_MCLK_ROOT_DIV>;
 		clock-names = "mclk";
 		ldoin-supply = <&reg_audio_3v3>;
 		iov-supply = <&reg_audio_3v3>;
diff --git a/arch/arm/boot/dts/imx7d-colibri-aster.dts b/arch/arm/boot/dts/imx7d-colibri-aster.dts
index f3f0537d5a37..90aaeddfb4f6 100644
--- a/arch/arm/boot/dts/imx7d-colibri-aster.dts
+++ b/arch/arm/boot/dts/imx7d-colibri-aster.dts
@@ -1,7 +1,6 @@
-// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
 /*
- * Copyright 2017-2020 Toradex AG
- *
+ * Copyright 2017-2022 Toradex
  */
 
 /dts-v1/;
@@ -10,11 +9,32 @@
 
 / {
 	model = "Toradex Colibri iMX7D on Aster Carrier Board";
-	compatible = "toradex,colibri-imx7d-aster", "toradex,colibri-imx7d",
+	compatible = "toradex,colibri-imx7d-aster",
+		     "toradex,colibri-imx7d",
 		     "fsl,imx7d";
 };
 
+&ad7879_ts {
+	status = "okay";
+};
+
+&atmel_mxt_ts {
+	status = "okay";
+};
+
+&backlight {
+	status = "okay";
+};
+
+&lcdif {
+	status = "okay";
+};
+
+&panel_dpi {
+	status = "okay";
+};
+
+/* Colibri USBH */
 &usbotg2 {
-	vbus-supply = <&reg_usbh_vbus>;
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/imx7d-colibri-emmc-aster.dts b/arch/arm/boot/dts/imx7d-colibri-emmc-aster.dts
index 20480276cb0e..3ec9ef6baaa4 100644
--- a/arch/arm/boot/dts/imx7d-colibri-emmc-aster.dts
+++ b/arch/arm/boot/dts/imx7d-colibri-emmc-aster.dts
@@ -1,6 +1,6 @@
-// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
 /*
- * Copyright 2017-2020 Toradex AG
+ * Copyright 2017-2022 Toradex
  *
  */
 
@@ -11,10 +11,12 @@
 / {
 	model = "Toradex Colibri iMX7D 1GB (eMMC) on Aster Carrier Board";
 	compatible = "toradex,colibri-imx7d-emmc-aster",
-		     "toradex,colibri-imx7d-emmc", "fsl,imx7d";
+		     "toradex,colibri-imx7d-emmc",
+		     "toradex,colibri-imx7d",
+		     "fsl,imx7d";
 };
 
+/* Colibri USBH */
 &usbotg2 {
-	vbus-supply = <&reg_usbh_vbus>;
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/imx7d-colibri-emmc-eval-v3.dts b/arch/arm/boot/dts/imx7d-colibri-emmc-eval-v3.dts
index 8ee73c870b12..6d505cb02aad 100644
--- a/arch/arm/boot/dts/imx7d-colibri-emmc-eval-v3.dts
+++ b/arch/arm/boot/dts/imx7d-colibri-emmc-eval-v3.dts
@@ -1,6 +1,6 @@
-// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
 /*
- * Copyright 2017 Toradex AG
+ * Copyright 2017-2022 Toradex
  */
 
 /dts-v1/;
@@ -10,10 +10,12 @@
 / {
 	model = "Toradex Colibri iMX7D 1GB (eMMC) on Colibri Evaluation Board V3";
 	compatible = "toradex,colibri-imx7d-emmc-eval-v3",
-		     "toradex,colibri-imx7d-emmc", "fsl,imx7d";
+		     "toradex,colibri-imx7d-emmc",
+		     "toradex,colibri-imx7d",
+		     "fsl,imx7d";
 };
 
+/* Colibri USBH */
 &usbotg2 {
-	vbus-supply = <&reg_usbh_vbus>;
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/imx7d-colibri-emmc-iris-v2.dts b/arch/arm/boot/dts/imx7d-colibri-emmc-iris-v2.dts
new file mode 100644
index 000000000000..7347659557f3
--- /dev/null
+++ b/arch/arm/boot/dts/imx7d-colibri-emmc-iris-v2.dts
@@ -0,0 +1,21 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/dts-v1/;
+#include "imx7d-colibri-emmc.dtsi"
+#include "imx7-colibri-iris-v2.dtsi"
+
+/ {
+	model = "Toradex Colibri iMX7D 1GB on Iris V2 Carrier Board";
+	compatible = "toradex,colibri-imx7d-emmc-iris-v2",
+		     "toradex,colibri-imx7d-emmc",
+		     "toradex,colibri-imx7d",
+		     "fsl,imx7d";
+};
+
+/* Colibri USBH */
+&usbotg2 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx7d-colibri-emmc-iris.dts b/arch/arm/boot/dts/imx7d-colibri-emmc-iris.dts
new file mode 100644
index 000000000000..5324c92e368d
--- /dev/null
+++ b/arch/arm/boot/dts/imx7d-colibri-emmc-iris.dts
@@ -0,0 +1,21 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/dts-v1/;
+#include "imx7d-colibri-emmc.dtsi"
+#include "imx7-colibri-iris.dtsi"
+
+/ {
+	model = "Toradex Colibri iMX7D 1GB on Iris Carrier Board";
+	compatible = "toradex,colibri-imx7d-emmc-iris",
+		     "toradex,colibri-imx7d-emmc",
+		     "toradex,colibri-imx7d",
+		     "fsl,imx7d";
+};
+
+/* Colibri USBH */
+&usbotg2 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx7d-colibri-emmc.dtsi b/arch/arm/boot/dts/imx7d-colibri-emmc.dtsi
index af39e5370fa1..2fb4d2133a1b 100644
--- a/arch/arm/boot/dts/imx7d-colibri-emmc.dtsi
+++ b/arch/arm/boot/dts/imx7d-colibri-emmc.dtsi
@@ -1,18 +1,28 @@
-// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
 /*
- * Copyright 2017 Toradex AG
+ * Copyright 2017-2022 Toradex
  */
 
 #include "imx7d.dtsi"
 #include "imx7-colibri.dtsi"
 
 / {
+	aliases {
+		/* Required to properly pass MAC addresses from bootloader. */
+		ethernet0 = &fec1;
+		ethernet1 = &fec2;
+	};
+
 	memory@80000000 {
 		device_type = "memory";
 		reg = <0x80000000 0x40000000>;
 	};
 };
 
+&cpu1 {
+	cpu-supply = <&reg_DCDC2>;
+};
+
 &gpio6 {
 	gpio-line-names = "",
 			  "",
@@ -39,10 +49,13 @@
 			  "SODIMM_34";
 };
 
+/* Colibri USBH */
 &usbotg2 {
 	dr_mode = "host";
+	vbus-supply = <&reg_usbh_vbus>;
 };
 
+/* eMMC */
 &usdhc3 {
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/imx7d-colibri-eval-v3.dts b/arch/arm/boot/dts/imx7d-colibri-eval-v3.dts
index 87b132bcd272..c7a8b5aa2408 100644
--- a/arch/arm/boot/dts/imx7d-colibri-eval-v3.dts
+++ b/arch/arm/boot/dts/imx7d-colibri-eval-v3.dts
@@ -1,6 +1,6 @@
-// SPDX-License-Identifier: GPL-2.0+ OR MIT
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
 /*
- * Copyright 2016-2020 Toradex
+ * Copyright 2016-2022 Toradex
  */
 
 /dts-v1/;
@@ -9,11 +9,48 @@
 
 / {
 	model = "Toradex Colibri iMX7D on Colibri Evaluation Board V3";
-	compatible = "toradex,colibri-imx7d-eval-v3", "toradex,colibri-imx7d",
+	compatible = "toradex,colibri-imx7d-eval-v3",
+		     "toradex,colibri-imx7d",
 		     "fsl,imx7d";
 };
 
+&ad7879_ts {
+	status = "okay";
+};
+
+/*
+ * The Atmel maxtouch controller uses SODIMM 28/30, also used for PWM<B>, PWM<C>, aka pwm2, pwm3.
+ * So if you enable following capacitive touch controller, disable pwm2/pwm3 first.
+ */
+&atmel_mxt_ts {
+	status = "disabled";
+};
+
+&backlight {
+	status = "okay";
+};
+
+&lcdif {
+	status = "okay";
+};
+
+&panel_dpi {
+	status = "okay";
+};
+
+/* Colibri PWM<B> */
+&pwm2 {
+	/* The pwm2 should be disabled to enable atmel_mxt_ts touchscreen for adapter. */
+	status = "okay";
+};
+
+/* Colibri PWM<C> */
+&pwm3 {
+	/* The pwm3 should be disabled to enable atmel_mxt_ts touchscreen for adapter. */
+	status = "okay";
+};
+
+/* Colibri USBH */
 &usbotg2 {
-	vbus-supply = <&reg_usbh_vbus>;
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/imx7d-colibri-iris-v2.dts b/arch/arm/boot/dts/imx7d-colibri-iris-v2.dts
new file mode 100644
index 000000000000..5762f51d5f0f
--- /dev/null
+++ b/arch/arm/boot/dts/imx7d-colibri-iris-v2.dts
@@ -0,0 +1,83 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/dts-v1/;
+#include "imx7d-colibri.dtsi"
+#include "imx7-colibri-iris-v2.dtsi"
+
+/ {
+	model = "Toradex Colibri iMX7D on Iris V2 Carrier Board";
+	compatible = "toradex,colibri-imx7d-iris-v2",
+		     "toradex,colibri-imx7d",
+		     "fsl,imx7d";
+};
+
+&ad7879_ts {
+	status = "okay";
+};
+
+&atmel_mxt_ts {
+	status = "okay";
+};
+
+&backlight {
+	status = "okay";
+};
+
+&gpio2 {
+	/*
+	 * This switches the LVDS transceiver to VESA color mapping mode.
+	 */
+	lvds-color-map-hog {
+		gpio-hog;
+		gpios = <13 GPIO_ACTIVE_HIGH>; /* SODIMM 95 */
+		line-name = "LVDS_COLOR_MAP";
+		output-low;
+	};
+};
+
+&gpio7 {
+	/*
+	 * This switches the LVDS transceiver to the 24-bit RGB mode.
+	 */
+	lvds-rgb-mode-hog {
+		gpio-hog;
+		gpios = <2 GPIO_ACTIVE_HIGH>; /* SODIMM 63 */
+		line-name = "LVDS_RGB_MODE";
+		output-low;
+	};
+
+	/*
+	 * This switches the LVDS transceiver to the single-channel
+	 * output mode.
+	 */
+	lvds-ch-mode-hog {
+		gpio-hog;
+		gpios = <3 GPIO_ACTIVE_HIGH>; /* SODIMM 55 */
+		line-name = "LVDS_CH_MODE";
+		output-high;
+	};
+
+	/* This turns the LVDS transceiver on */
+	lvds-power-on-hog {
+		gpio-hog;
+		gpios = <11 GPIO_ACTIVE_HIGH>; /* SODIMM 99 */
+		line-name = "LVDS_POWER_ON";
+		output-high;
+	};
+};
+
+&lcdif {
+	status = "okay";
+};
+
+&panel_dpi {
+	status = "okay";
+};
+
+/* Colibri USBH */
+&usbotg2 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx7d-colibri-iris.dts b/arch/arm/boot/dts/imx7d-colibri-iris.dts
new file mode 100644
index 000000000000..9c63cb9d9a64
--- /dev/null
+++ b/arch/arm/boot/dts/imx7d-colibri-iris.dts
@@ -0,0 +1,56 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/dts-v1/;
+#include "imx7d-colibri.dtsi"
+#include "imx7-colibri-iris.dtsi"
+
+/ {
+	model = "Toradex Colibri iMX7D on Iris Carrier Board";
+	compatible = "toradex,colibri-imx7d-iris",
+		     "toradex,colibri-imx7d",
+		     "fsl,imx7d";
+};
+
+&ad7879_ts {
+	status = "okay";
+};
+
+/*
+ * The Atmel maxtouch controller uses SODIMM 28/30, also used for PWM<B>, PWM<C>, aka pwm2, pwm3.
+ * So if you enable following capacitive touch controller, disable pwm2/pwm3 first.
+ */
+&atmel_mxt_ts {
+	status = "disabled";
+};
+
+&backlight {
+	status = "okay";
+};
+
+&lcdif {
+	status = "okay";
+};
+
+&panel_dpi {
+	status = "okay";
+};
+
+/* Colibri PWM<B> */
+&pwm2 {
+	/* The pwm2 should be disabled to enable atmel_mxt_ts touchscreen for adapter. */
+	status = "okay";
+};
+
+/* Colibri PWM<C> */
+&pwm3 {
+	/* The pwm3 should be disabled to enable atmel_mxt_ts touchscreen for adapter. */
+	status = "okay";
+};
+
+/* Colibri USBH */
+&usbotg2 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx7d-colibri.dtsi b/arch/arm/boot/dts/imx7d-colibri.dtsi
index 219a0404a058..531a45b176a1 100644
--- a/arch/arm/boot/dts/imx7d-colibri.dtsi
+++ b/arch/arm/boot/dts/imx7d-colibri.dtsi
@@ -1,12 +1,18 @@
-// SPDX-License-Identifier: GPL-2.0+ OR MIT
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
 /*
- * Copyright 2016-2020 Toradex
+ * Copyright 2016-2022 Toradex
  */
 
 #include "imx7d.dtsi"
 #include "imx7-colibri.dtsi"
 
 / {
+	aliases {
+		/* Required to properly pass MAC addresses from bootloader. */
+		ethernet0 = &fec1;
+		ethernet1 = &fec2;
+	};
+
 	memory@80000000 {
 		device_type = "memory";
 		reg = <0x80000000 0x20000000>;
@@ -17,10 +23,13 @@
 	cpu-supply = <&reg_DCDC2>;
 };
 
+/* NAND */
 &gpmi {
 	status = "okay";
 };
 
+/* Colibri USBH */
 &usbotg2 {
 	dr_mode = "host";
+	vbus-supply = <&reg_usbh_vbus>;
 };
diff --git a/arch/arm/boot/dts/imx7d-nitrogen7.dts b/arch/arm/boot/dts/imx7d-nitrogen7.dts
index e0751e6ba3c0..a31de900139d 100644
--- a/arch/arm/boot/dts/imx7d-nitrogen7.dts
+++ b/arch/arm/boot/dts/imx7d-nitrogen7.dts
@@ -288,7 +288,7 @@
 	codec: wm8960@1a {
 		compatible = "wlf,wm8960";
 		reg = <0x1a>;
-		clocks = <&clks IMX7D_AUDIO_MCLK_ROOT_CLK>;
+		clocks = <&clks IMX7D_AUDIO_MCLK_ROOT_DIV>;
 		clock-names = "mclk";
 		wlf,shared-lrclk;
 	};
diff --git a/arch/arm/boot/dts/imx7d-pico-hobbit.dts b/arch/arm/boot/dts/imx7d-pico-hobbit.dts
index 7b2198a9372c..d917dc4f2f22 100644
--- a/arch/arm/boot/dts/imx7d-pico-hobbit.dts
+++ b/arch/arm/boot/dts/imx7d-pico-hobbit.dts
@@ -31,7 +31,7 @@
 
 		dailink_master: simple-audio-card,codec {
 			sound-dai = <&sgtl5000>;
-			clocks = <&clks IMX7D_AUDIO_MCLK_ROOT_CLK>;
+			clocks = <&clks IMX7D_AUDIO_MCLK_ROOT_DIV>;
 		};
 	};
 };
@@ -41,7 +41,7 @@
 		#sound-dai-cells = <0>;
 		reg = <0x0a>;
 		compatible = "fsl,sgtl5000";
-		clocks = <&clks IMX7D_AUDIO_MCLK_ROOT_CLK>;
+		clocks = <&clks IMX7D_AUDIO_MCLK_ROOT_DIV>;
 		VDDA-supply = <&reg_2p5v>;
 		VDDIO-supply = <&reg_vref_1v8>;
 	};
diff --git a/arch/arm/boot/dts/imx7d-pico-pi.dts b/arch/arm/boot/dts/imx7d-pico-pi.dts
index 70bea95c06d8..f263e391e24c 100644
--- a/arch/arm/boot/dts/imx7d-pico-pi.dts
+++ b/arch/arm/boot/dts/imx7d-pico-pi.dts
@@ -31,7 +31,7 @@
 
 		dailink_master: simple-audio-card,codec {
 			sound-dai = <&sgtl5000>;
-			clocks = <&clks IMX7D_AUDIO_MCLK_ROOT_CLK>;
+			clocks = <&clks IMX7D_AUDIO_MCLK_ROOT_DIV>;
 		};
 	};
 };
@@ -41,7 +41,7 @@
 		#sound-dai-cells = <0>;
 		reg = <0x0a>;
 		compatible = "fsl,sgtl5000";
-		clocks = <&clks IMX7D_AUDIO_MCLK_ROOT_CLK>;
+		clocks = <&clks IMX7D_AUDIO_MCLK_ROOT_DIV>;
 		VDDA-supply = <&reg_2p5v>;
 		VDDIO-supply = <&reg_vref_1v8>;
 	};
diff --git a/arch/arm/boot/dts/imx7d-pico.dtsi b/arch/arm/boot/dts/imx7d-pico.dtsi
index e519897fae08..e0bff39e8d3e 100644
--- a/arch/arm/boot/dts/imx7d-pico.dtsi
+++ b/arch/arm/boot/dts/imx7d-pico.dtsi
@@ -41,7 +41,7 @@
 		regulator-max-microvolt = <3300000>;
 		gpio = <&gpio1 6 GPIO_ACTIVE_HIGH>;
 		enable-active-high;
-        };
+	};
 
 	reg_wlreg_on: regulator-wlreg_on {
 		compatible = "regulator-fixed";
@@ -432,7 +432,7 @@
 			MX7D_PAD_ENET1_RGMII_RD2__ENET1_RGMII_RD2	0x1
 			MX7D_PAD_ENET1_RGMII_RD3__ENET1_RGMII_RD3	0x1
 			MX7D_PAD_ENET1_RGMII_RX_CTL__ENET1_RGMII_RX_CTL	0x1
-			MX7D_PAD_SD3_RESET_B__GPIO6_IO11                0x1  /* Ethernet reset */
+			MX7D_PAD_SD3_RESET_B__GPIO6_IO11		0x1  /* Ethernet reset */
 		>;
 	};
 
@@ -493,19 +493,19 @@
 
 	pinctrl_pwm1: pwm1 {
 		fsl,pins = <
-			MX7D_PAD_GPIO1_IO08__PWM1_OUT   0x7f
+			MX7D_PAD_GPIO1_IO08__PWM1_OUT	0x7f
 		>;
 	};
 
 	pinctrl_pwm2: pwm2 {
 		fsl,pins = <
-			MX7D_PAD_GPIO1_IO09__PWM2_OUT   0x7f
+			MX7D_PAD_GPIO1_IO09__PWM2_OUT	0x7f
 		>;
 	};
 
 	pinctrl_pwm3: pwm3 {
 		fsl,pins = <
-			MX7D_PAD_GPIO1_IO10__PWM3_OUT   0x7f
+			MX7D_PAD_GPIO1_IO10__PWM3_OUT	0x7f
 		>;
 	};
 
diff --git a/arch/arm/boot/dts/imx7d-remarkable2.dts b/arch/arm/boot/dts/imx7d-remarkable2.dts
index 89cbf13097a4..a2a91bfdd98e 100644
--- a/arch/arm/boot/dts/imx7d-remarkable2.dts
+++ b/arch/arm/boot/dts/imx7d-remarkable2.dts
@@ -34,6 +34,19 @@
 		startup-delay-us = <150>;
 	};
 
+	reg_digitizer: regulator-digitizer {
+		compatible = "regulator-fixed";
+		regulator-name = "VDD_3V3_DIGITIZER";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		pinctrl-names = "default", "sleep";
+		pinctrl-0 = <&pinctrl_digitizer_reg>;
+		pinctrl-1 = <&pinctrl_digitizer_reg>;
+		gpio = <&gpio1 6 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		startup-delay-us = <100000>; /* 100 ms */
+	};
+
 	wifi_pwrseq: wifi_pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		pinctrl-names = "default";
@@ -51,6 +64,26 @@
 	assigned-clock-rates = <0>, <32768>;
 };
 
+&i2c1 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+
+	wacom_digitizer: digitizer@9 {
+		compatible = "hid-over-i2c";
+		reg = <0x09>;
+		hid-descr-addr = <0x01>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_wacom>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
+		touchscreen-inverted-x;
+		touchscreen-inverted-y;
+		vdd-supply = <&reg_digitizer>;
+	};
+};
+
 &snvs_pwrkey {
 	status = "okay";
 };
@@ -117,6 +150,25 @@
 	fsl,ext-reset-output;
 };
 
+&iomuxc_lpsr {
+	pinctrl_digitizer_reg: digitizerreggrp {
+		fsl,pins = <
+			/* DIGITIZER_PWR_EN */
+			MX7D_PAD_LPSR_GPIO1_IO06__GPIO1_IO6	0x14
+		>;
+	};
+
+	pinctrl_wacom: wacomgrp {
+		fsl,pins = <
+			/*MX7D_PAD_LPSR_GPIO1_IO05__GPIO1_IO5	0x00000014 FWE */
+			MX7D_PAD_LPSR_GPIO1_IO04__GPIO1_IO4	0x00000074 /* PDCTB */
+			MX7D_PAD_LPSR_GPIO1_IO01__GPIO1_IO1	0x00000034 /* WACOM INT */
+			/*MX7D_PAD_LPSR_GPIO1_IO06__GPIO1_IO6	0x00000014 WACOM PWR ENABLE */
+			/*MX7D_PAD_LPSR_GPIO1_IO00__GPIO1_IO0	0x00000074 WACOM RESET */
+		>;
+	};
+};
+
 &iomuxc {
 	pinctrl_brcm_reg: brcmreggrp {
 		fsl,pins = <
@@ -125,6 +177,13 @@
 		>;
 	};
 
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX7D_PAD_I2C1_SDA__I2C1_SDA		0x4000007f
+			MX7D_PAD_I2C1_SCL__I2C1_SCL		0x4000007f
+		>;
+	};
+
 	pinctrl_uart1: uart1grp {
 		fsl,pins = <
 			MX7D_PAD_UART1_TX_DATA__UART1_DCE_TX	0x79
diff --git a/arch/arm/boot/dts/imx7d-sdb.dts b/arch/arm/boot/dts/imx7d-sdb.dts
index 7813ef960f6e..f483bc0afe5e 100644
--- a/arch/arm/boot/dts/imx7d-sdb.dts
+++ b/arch/arm/boot/dts/imx7d-sdb.dts
@@ -24,14 +24,14 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gpio_keys>;
 
-		volume-up {
+		key-volume-up {
 			label = "Volume Up";
 			gpios = <&gpio5 11 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_VOLUMEUP>;
 			wakeup-source;
 		};
 
-		volume-down {
+		key-volume-down {
 			label = "Volume Down";
 			gpios = <&gpio5 10 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_VOLUMEDOWN>;
@@ -39,7 +39,7 @@
 		};
 	};
 
-	spi4 {
+	spi-4 {
 		compatible = "spi-gpio";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_spi4>;
@@ -201,17 +201,12 @@
 		compatible = "ti,tsc2046";
 		reg = <0>;
 		spi-max-frequency = <1000000>;
-		pinctrl-names ="default";
+		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_tsc2046_pendown>;
 		interrupt-parent = <&gpio2>;
 		interrupts = <29 0>;
 		pendown-gpio = <&gpio2 29 GPIO_ACTIVE_HIGH>;
-		ti,x-min = /bits/ 16 <0>;
-		ti,x-max = /bits/ 16 <0>;
-		ti,y-min = /bits/ 16 <0>;
-		ti,y-max = /bits/ 16 <0>;
-		ti,pressure-max = /bits/ 16 <0>;
-		ti,x-plate-ohms = /bits/ 16 <400>;
+		touchscreen-max-pressure = <255>;
 		wakeup-source;
 	};
 };
@@ -385,14 +380,14 @@
 	codec: wm8960@1a {
 		compatible = "wlf,wm8960";
 		reg = <0x1a>;
-		clocks = <&clks IMX7D_AUDIO_MCLK_ROOT_CLK>;
+		clocks = <&clks IMX7D_AUDIO_MCLK_ROOT_DIV>;
 		clock-names = "mclk";
 		wlf,shared-lrclk;
 		wlf,hp-cfg = <2 2 3>;
 		wlf,gpio-cfg = <1 3>;
 		assigned-clocks = <&clks IMX7D_AUDIO_MCLK_ROOT_SRC>,
 				  <&clks IMX7D_PLL_AUDIO_POST_DIV>,
-				  <&clks IMX7D_AUDIO_MCLK_ROOT_CLK>;
+				  <&clks IMX7D_AUDIO_MCLK_ROOT_DIV>;
 		assigned-clock-parents = <&clks IMX7D_PLL_AUDIO_POST_DIV>;
 		assigned-clock-rates = <0>, <884736000>, <12288000>;
 	};
diff --git a/arch/arm/boot/dts/imx7d-smegw01.dts b/arch/arm/boot/dts/imx7d-smegw01.dts
new file mode 100644
index 000000000000..546268b8d0b1
--- /dev/null
+++ b/arch/arm/boot/dts/imx7d-smegw01.dts
@@ -0,0 +1,467 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+//
+// Copyright (C) 2020 PHYTEC Messtechnik GmbH
+// Author: Jens Lang  <J.Lang@phytec.de>
+// Copyright (C) 2021 Fabio Estevam <festevam@denx.de>
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include "imx7d.dtsi"
+
+/ {
+	model = "Storopack SMEGW01 board";
+	compatible = "storopack,imx7d-smegw01", "fsl,imx7d";
+
+	aliases {
+		mmc0 = &usdhc1;
+		mmc1 = &usdhc3;
+		mmc2 = &usdhc2;
+		rtc0 = &i2c_rtc;
+		rtc1 = &snvs_rtc;
+	};
+
+	chosen {
+		stdout-path = &uart1;
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x20000000>;
+	};
+
+	reg_lte_on: regulator-lte-on {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_lte_on>;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-name = "lte_on";
+		gpio = <&gpio7 12 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-always-on;
+	};
+
+	reg_lte_nreset: regulator-lte-nreset {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_lte_nreset>;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-name = "LTE_nReset";
+		gpio = <&gpio6 21 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-always-on;
+	};
+
+	reg_wifi: regulator-wifi {
+		compatible = "regulator-fixed";
+		gpio = <&gpio2 30 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_wifi>;
+		regulator-name = "wifi_reg";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	reg_wlan_rfkill: regulator-wlan-rfkill {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-2 = <&pinctrl_rfkill>;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-name = "wlan_rfkill";
+		gpio = <&gpio2 11 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-always-on;
+	};
+
+	reg_usbotg_vbus: regulator-usbotg-vbus {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usbotg1_pwr_gpio>;
+		regulator-name = "usb_otg_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio1 05 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+};
+
+&ecspi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1>;
+	cs-gpios = <&gpio4 19 GPIO_ACTIVE_LOW>;
+	status = "okay";
+
+	sram@0 {
+		compatible = "microchip,48l640";
+		reg = <0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		spi-max-frequency = <16000000>;
+	};
+};
+
+&fec1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet1>;
+	assigned-clocks = <&clks IMX7D_ENET1_TIME_ROOT_SRC>,
+			  <&clks IMX7D_ENET1_TIME_ROOT_CLK>;
+	assigned-clock-parents = <&clks IMX7D_PLL_ENET_MAIN_100M_CLK>;
+	assigned-clock-rates = <0>, <100000000>;
+	phy-mode = "rgmii-id";
+	phy-handle = <&ethphy0>;
+	fsl,magic-packet;
+	status = "okay";
+
+	mdio: mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy0: ethernet-phy@1 {
+			compatible = "ethernet-phy-id0022.1622",
+				     "ethernet-phy-ieee802.3-c22";
+			reg = <1>;
+			reset-gpios = <&gpio2 28 GPIO_ACTIVE_LOW>;
+		};
+
+		ethphy1: ethernet-phy@2 {
+			compatible = "ethernet-phy-id0022.1622",
+				     "ethernet-phy-ieee802.3-c22";
+			reg = <2>;
+		};
+	};
+};
+
+&fec2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet2>;
+	assigned-clocks = <&clks IMX7D_ENET2_TIME_ROOT_SRC>,
+			  <&clks IMX7D_ENET2_TIME_ROOT_CLK>;
+	assigned-clock-parents = <&clks IMX7D_PLL_ENET_MAIN_100M_CLK>;
+	assigned-clock-rates = <0>, <100000000>;
+	phy-mode = "rgmii-id";
+	phy-handle = <&ethphy1>;
+	fsl,magic-packet;
+	status = "okay";
+};
+
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 =<&pinctrl_i2c2>;
+	clock-frequency = <100000>;
+	status = "okay";
+
+	i2c_rtc: rtc@52 {
+		compatible = "microcrystal,rv3028";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_rtc_int>;
+		reg = <0x52>;
+		interrupt-parent = <&gpio2>;
+		interrupts = <15 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
+&flexcan1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan1>;
+	status = "okay";
+};
+
+&flexcan2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan2>;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	status = "okay";
+};
+
+&usbotg1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg1_lpsr>;
+	dr_mode = "otg";
+	vbus-supply = <&reg_usbotg_vbus>;
+	status = "okay";
+};
+
+&usbotg2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg2>;
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usdhc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	cd-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>;
+	no-1-8-v;
+	wakeup-source;
+	keep-power-in-suspend;
+	status = "okay";
+};
+
+&usdhc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	bus-width = <4>;
+	no-1-8-v;
+	non-removable;
+	vmmc-supply = <&reg_wifi>;
+	wakeup-source;
+	status = "okay";
+};
+
+&usdhc3 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+	assigned-clocks = <&clks IMX7D_USDHC3_ROOT_CLK>;
+	assigned-clock-rates = <400000000>;
+	max-frequency = <200000000>;
+	bus-width = <8>;
+	fsl,tuning-step = <1>;
+	non-removable;
+	cap-mmc-highspeed;
+	cap-mmc-hw-reset;
+	mmc-hs200-1_8v;
+	mmc-ddr-1_8v;
+	status = "okay";
+};
+
+&wdog1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog>;
+	fsl,ext-reset-output;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_ecspi1: ecspi1grp {
+		fsl,pins = <
+			MX7D_PAD_ECSPI1_SS0__GPIO4_IO19	0x04
+			MX7D_PAD_ECSPI1_SCLK__ECSPI1_SCLK	0x04
+			MX7D_PAD_ECSPI1_MOSI__ECSPI1_MOSI	0x04
+			MX7D_PAD_ECSPI1_MISO__ECSPI1_MISO	0x04
+		>;
+	};
+
+	pinctrl_enet1: enet1grp {
+		fsl,pins = <
+			MX7D_PAD_ENET1_RGMII_RX_CTL__ENET1_RGMII_RX_CTL 0x5
+			MX7D_PAD_ENET1_RGMII_RD0__ENET1_RGMII_RD0	0x5
+			MX7D_PAD_ENET1_RGMII_RD1__ENET1_RGMII_RD1	0x5
+			MX7D_PAD_ENET1_RGMII_RD2__ENET1_RGMII_RD2	0x5
+			MX7D_PAD_ENET1_RGMII_RD3__ENET1_RGMII_RD3	0x5
+			MX7D_PAD_ENET1_RGMII_RXC__ENET1_RGMII_RXC	0x5
+			MX7D_PAD_ENET1_RGMII_TX_CTL__ENET1_RGMII_TX_CTL 0x5
+			MX7D_PAD_ENET1_RGMII_TD0__ENET1_RGMII_TD0	0x5
+			MX7D_PAD_ENET1_RGMII_TD1__ENET1_RGMII_TD1	0x5
+			MX7D_PAD_ENET1_RGMII_TD2__ENET1_RGMII_TD2	0x5
+			MX7D_PAD_ENET1_RGMII_TD3__ENET1_RGMII_TD3	0x5
+			MX7D_PAD_ENET1_RGMII_TXC__ENET1_RGMII_TXC	0x5
+			MX7D_PAD_GPIO1_IO10__ENET1_MDIO		0x7
+			MX7D_PAD_GPIO1_IO11__ENET1_MDC		0x7
+		>;
+	};
+
+	pinctrl_enet2: enet2grp {
+		fsl,pins = <
+			MX7D_PAD_EPDC_SDCE0__ENET2_RGMII_RX_CTL 0x5
+			MX7D_PAD_EPDC_SDCE1__ENET2_RGMII_RXC	0x5
+			MX7D_PAD_EPDC_SDCLK__ENET2_RGMII_RD0	0x5
+			MX7D_PAD_EPDC_SDLE__ENET2_RGMII_RD1	0x5
+			MX7D_PAD_EPDC_SDOE__ENET2_RGMII_RD2	0x5
+			MX7D_PAD_EPDC_SDSHR__ENET2_RGMII_RD3	0x5
+			MX7D_PAD_EPDC_SDCE2__ENET2_RGMII_TD0	0x5
+			MX7D_PAD_EPDC_SDCE3__ENET2_RGMII_TD1	0x5
+			MX7D_PAD_EPDC_GDCLK__ENET2_RGMII_TD2	0x5
+			MX7D_PAD_EPDC_GDOE__ENET2_RGMII_TD3	0x5
+			MX7D_PAD_EPDC_GDRL__ENET2_RGMII_TX_CTL 0x5
+			MX7D_PAD_EPDC_GDSP__ENET2_RGMII_TXC	0x5
+			MX7D_PAD_GPIO1_IO09__GPIO1_IO9	0x08
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX7D_PAD_I2C2_SCL__I2C2_SCL		0x40000004
+			MX7D_PAD_I2C2_SDA__I2C2_SDA		0x40000004
+		>;
+	};
+
+	pinctrl_flexcan1: flexcan1grp {
+		fsl,pins = <
+			MX7D_PAD_GPIO1_IO12__FLEXCAN1_RX	0x0b0b0
+			MX7D_PAD_GPIO1_IO13__FLEXCAN1_TX	0x0b0b0
+		>;
+	};
+
+	pinctrl_flexcan2: flexcan2grp {
+		fsl,pins = <
+			MX7D_PAD_GPIO1_IO14__FLEXCAN2_RX	0x0b0b0
+			MX7D_PAD_GPIO1_IO15__FLEXCAN2_TX	0x0b0b0
+		>;
+	};
+
+	pinctrl_lte_on: lteongrp {
+		fsl,pins = <
+			MX7D_PAD_ENET1_TX_CLK__GPIO7_IO12	0x17059
+		>;
+	};
+
+	pinctrl_lte_nreset: ltenresetgrp {
+		fsl,pins = <
+			MX7D_PAD_SAI2_RX_DATA__GPIO6_IO21	0x17059
+		>;
+	};
+
+	pinctrl_rfkill: rfkillrp {
+		fsl,pins = <
+			MX7D_PAD_EPDC_DATA11__GPIO2_IO11	0x17059
+		>;
+	};
+
+	pinctrl_rtc_int: rtcintgrp {
+		fsl,pins = <
+			MX7D_PAD_EPDC_DATA15__GPIO2_IO15	0x17059
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX7D_PAD_UART1_TX_DATA__UART1_DCE_TX	0x74
+			MX7D_PAD_UART1_RX_DATA__UART1_DCE_RX	0x7c
+		>;
+	};
+
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <
+			MX7D_PAD_UART3_TX_DATA__UART3_DCE_TX	0x7c
+			MX7D_PAD_UART3_RX_DATA__UART3_DCE_RX	0x74
+		>;
+	};
+
+	pinctrl_usbotg1_lpsr: usbotg1 {
+		fsl,pins = <
+			MX7D_PAD_LPSR_GPIO1_IO04__USB_OTG1_OC	0x04
+		>;
+	};
+
+	pinctrl_usbotg1_pwr: usbotg1-pwr {
+		fsl,pins = <
+			MX7D_PAD_LPSR_GPIO1_IO05__USB_OTG1_PWR	0x04
+		>;
+	};
+
+	pinctrl_usbotg1_pwr_gpio: usbotg1-pwr-gpio {
+		fsl,pins = <
+			MX7D_PAD_LPSR_GPIO1_IO05__GPIO1_IO5	0x04
+		>;
+	};
+
+	pinctrl_usbotg2: usbotg2grp {
+		fsl,pins = <
+			MX7D_PAD_UART3_RTS_B__USB_OTG2_OC	0x04
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX7D_PAD_SD1_CD_B__GPIO5_IO0		0x59
+			MX7D_PAD_SD1_CMD__SD1_CMD		0x59
+			MX7D_PAD_SD1_CLK__SD1_CLK		0x19
+			MX7D_PAD_SD1_DATA0__SD1_DATA0		0x59
+			MX7D_PAD_SD1_DATA1__SD1_DATA1		0x59
+			MX7D_PAD_SD1_DATA2__SD1_DATA2		0x59
+			MX7D_PAD_SD1_DATA3__SD1_DATA3		0x59
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX7D_PAD_SD2_CLK__SD2_CLK		0x19
+			MX7D_PAD_SD2_CMD__SD2_CMD		0x59
+			MX7D_PAD_SD2_DATA0__SD2_DATA0		0x59
+			MX7D_PAD_SD2_DATA1__SD2_DATA1		0x59
+			MX7D_PAD_SD2_DATA2__SD2_DATA2		0x59
+			MX7D_PAD_SD2_DATA3__SD2_DATA3		0x59
+			MX7D_PAD_SD2_CD_B__SD2_CD_B		0x08
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX7D_PAD_SD3_CMD__SD3_CMD		0x5d
+			MX7D_PAD_SD3_CLK__SD3_CLK		0x1d
+			MX7D_PAD_SD3_DATA0__SD3_DATA0		0x5d
+			MX7D_PAD_SD3_DATA1__SD3_DATA1		0x5d
+			MX7D_PAD_SD3_DATA2__SD3_DATA2		0x5d
+			MX7D_PAD_SD3_DATA3__SD3_DATA3		0x5d
+			MX7D_PAD_SD3_DATA4__SD3_DATA4		0x5d
+			MX7D_PAD_SD3_DATA5__SD3_DATA5		0x5d
+			MX7D_PAD_SD3_DATA6__SD3_DATA6		0x5d
+			MX7D_PAD_SD3_DATA7__SD3_DATA7		0x5d
+			MX7D_PAD_SD3_STROBE__SD3_STROBE	0x1d
+		>;
+	};
+
+	pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
+		fsl,pins = <
+			MX7D_PAD_SD3_CMD__SD3_CMD		0x5e
+			MX7D_PAD_SD3_CLK__SD3_CLK		0x1e
+			MX7D_PAD_SD3_DATA0__SD3_DATA0		0x5e
+			MX7D_PAD_SD3_DATA1__SD3_DATA1		0x5e
+			MX7D_PAD_SD3_DATA2__SD3_DATA2		0x5e
+			MX7D_PAD_SD3_DATA3__SD3_DATA3		0x5e
+			MX7D_PAD_SD3_DATA4__SD3_DATA4		0x5e
+			MX7D_PAD_SD3_DATA5__SD3_DATA5		0x5e
+			MX7D_PAD_SD3_DATA6__SD3_DATA6		0x5e
+			MX7D_PAD_SD3_DATA7__SD3_DATA7		0x5e
+			MX7D_PAD_SD3_STROBE__SD3_STROBE	0x1e
+		>;
+	};
+
+	pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
+		fsl,pins = <
+			MX7D_PAD_SD3_CMD__SD3_CMD		0x5f
+			MX7D_PAD_SD3_CLK__SD3_CLK		0x0f
+			MX7D_PAD_SD3_DATA0__SD3_DATA0		0x5f
+			MX7D_PAD_SD3_DATA1__SD3_DATA1		0x5f
+			MX7D_PAD_SD3_DATA2__SD3_DATA2		0x5f
+			MX7D_PAD_SD3_DATA3__SD3_DATA3		0x5f
+			MX7D_PAD_SD3_DATA4__SD3_DATA4		0x5f
+			MX7D_PAD_SD3_DATA5__SD3_DATA5		0x5f
+			MX7D_PAD_SD3_DATA6__SD3_DATA6		0x5f
+			MX7D_PAD_SD3_DATA7__SD3_DATA7		0x5f
+			MX7D_PAD_SD3_STROBE__SD3_STROBE	0x1f
+		>;
+	};
+
+	pinctrl_wifi: wifigrp {
+		fsl,pins = <
+			MX7D_PAD_EPDC_PWR_COM__GPIO2_IO30	0x04
+			MX7D_PAD_SD2_RESET_B__GPIO5_IO11	0x04
+		>;
+	};
+};
+
+&iomuxc_lpsr {
+	pinctrl_wdog: wdoggrp {
+		fsl,pins = <
+			MX7D_PAD_LPSR_GPIO1_IO00__WDOG1_WDOG_B 0x74
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/imx7d-zii-rmu2.dts b/arch/arm/boot/dts/imx7d-zii-rmu2.dts
index 1065941807e8..1c9f25848bf7 100644
--- a/arch/arm/boot/dts/imx7d-zii-rmu2.dts
+++ b/arch/arm/boot/dts/imx7d-zii-rmu2.dts
@@ -24,7 +24,7 @@
 		pinctrl-0 = <&pinctrl_leds_debug>;
 		pinctrl-names = "default";
 
-		debug {
+		led-debug {
 			label = "zii:green:debug1";
 			gpios = <&gpio2 8 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
diff --git a/arch/arm/boot/dts/imx7d-zii-rpu2.dts b/arch/arm/boot/dts/imx7d-zii-rpu2.dts
index 893bd30aa2a3..9d29490ab4c9 100644
--- a/arch/arm/boot/dts/imx7d-zii-rpu2.dts
+++ b/arch/arm/boot/dts/imx7d-zii-rpu2.dts
@@ -36,7 +36,7 @@
 		pinctrl-0 = <&pinctrl_leds_debug>;
 		pinctrl-names = "default";
 
-		debug {
+		led-debug {
 			label = "zii:green:debug1";
 			gpios = <&gpio2 8 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
diff --git a/arch/arm/boot/dts/imx7d.dtsi b/arch/arm/boot/dts/imx7d.dtsi
index b7735979b7e4..7ceb7c09f7ad 100644
--- a/arch/arm/boot/dts/imx7d.dtsi
+++ b/arch/arm/boot/dts/imx7d.dtsi
@@ -78,7 +78,7 @@
 		#phy-cells = <0>;
 	};
 
-	soc {
+	soc: soc {
 		etm@3007d000 {
 			compatible = "arm,coresight-etm3x", "arm,primecell";
 			reg = <0x3007d000 0x1000>;
@@ -113,6 +113,49 @@
 			      <0x31004000 0x2000>,
 			      <0x31006000 0x2000>;
 		};
+
+		pcie: pcie@33800000 {
+			compatible = "fsl,imx7d-pcie";
+			reg = <0x33800000 0x4000>,
+			      <0x4ff00000 0x80000>;
+			reg-names = "dbi", "config";
+			#address-cells = <3>;
+			#size-cells = <2>;
+			device_type = "pci";
+			bus-range = <0x00 0xff>;
+			ranges = <0x81000000 0 0          0x4ff80000 0 0x00010000>, /* downstream I/O */
+				 <0x82000000 0 0x40000000 0x40000000 0 0x0ff00000>; /* non-prefetchable memory */
+			num-lanes = <1>;
+			interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "msi";
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0x7>;
+			/*
+			 * Reference manual lists pci irqs incorrectly
+			 * Real hardware ordering is same as imx6: D+MSI, C, B, A
+			 */
+			interrupt-map = <0 0 0 1 &intc GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>,
+					<0 0 0 2 &intc GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>,
+					<0 0 0 3 &intc GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
+					<0 0 0 4 &intc GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clks IMX7D_PCIE_CTRL_ROOT_CLK>,
+				 <&clks IMX7D_PLL_ENET_MAIN_100M_CLK>,
+				 <&clks IMX7D_PCIE_PHY_ROOT_CLK>;
+			clock-names = "pcie", "pcie_bus", "pcie_phy";
+			assigned-clocks = <&clks IMX7D_PCIE_CTRL_ROOT_SRC>,
+					  <&clks IMX7D_PCIE_PHY_ROOT_SRC>;
+			assigned-clock-parents = <&clks IMX7D_PLL_ENET_MAIN_250M_CLK>,
+						 <&clks IMX7D_PLL_ENET_MAIN_100M_CLK>;
+
+			fsl,max-link-speed = <2>;
+			power-domains = <&pgc_pcie_phy>;
+			resets = <&src IMX7_RESET_PCIEPHY>,
+				 <&src IMX7_RESET_PCIE_CTRL_APPS_EN>,
+				 <&src IMX7_RESET_PCIE_CTRL_APPS_TURNOFF>;
+			reset-names = "pciephy", "apps", "turnoff";
+			fsl,imx7d-pcie-phy = <&pcie_phy>;
+			status = "disabled";
+		};
 	};
 };
 
@@ -162,49 +205,6 @@
 		fsl,stop-mode = <&gpr 0x10 4>;
 		status = "disabled";
 	};
-
-	pcie: pcie@33800000 {
-		compatible = "fsl,imx7d-pcie";
-		reg = <0x33800000 0x4000>,
-		      <0x4ff00000 0x80000>;
-		reg-names = "dbi", "config";
-		#address-cells = <3>;
-		#size-cells = <2>;
-		device_type = "pci";
-		bus-range = <0x00 0xff>;
-		ranges = <0x81000000 0 0          0x4ff80000 0 0x00010000>, /* downstream I/O */
-			 <0x82000000 0 0x40000000 0x40000000 0 0x0ff00000>; /* non-prefetchable memory */
-		num-lanes = <1>;
-		interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>;
-		interrupt-names = "msi";
-		#interrupt-cells = <1>;
-		interrupt-map-mask = <0 0 0 0x7>;
-		/*
-		 * Reference manual lists pci irqs incorrectly
-		 * Real hardware ordering is same as imx6: D+MSI, C, B, A
-		 */
-		interrupt-map = <0 0 0 1 &intc GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>,
-				<0 0 0 2 &intc GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>,
-				<0 0 0 3 &intc GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
-				<0 0 0 4 &intc GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&clks IMX7D_PCIE_CTRL_ROOT_CLK>,
-			 <&clks IMX7D_PLL_ENET_MAIN_100M_CLK>,
-			 <&clks IMX7D_PCIE_PHY_ROOT_CLK>;
-		clock-names = "pcie", "pcie_bus", "pcie_phy";
-		assigned-clocks = <&clks IMX7D_PCIE_CTRL_ROOT_SRC>,
-				  <&clks IMX7D_PCIE_PHY_ROOT_SRC>;
-		assigned-clock-parents = <&clks IMX7D_PLL_ENET_MAIN_250M_CLK>,
-					 <&clks IMX7D_PLL_ENET_MAIN_100M_CLK>;
-
-		fsl,max-link-speed = <2>;
-		power-domains = <&pgc_pcie_phy>;
-		resets = <&src IMX7_RESET_PCIEPHY>,
-			 <&src IMX7_RESET_PCIE_CTRL_APPS_EN>,
-			 <&src IMX7_RESET_PCIE_CTRL_APPS_TURNOFF>;
-		reset-names = "pciephy", "apps", "turnoff";
-		fsl,imx7d-pcie-phy = <&pcie_phy>;
-		status = "disabled";
-	};
 };
 
 &ca_funnel_in_ports {
diff --git a/arch/arm/boot/dts/imx7s-colibri-aster.dts b/arch/arm/boot/dts/imx7s-colibri-aster.dts
index fca4e0a95c1b..58ebb02d948a 100644
--- a/arch/arm/boot/dts/imx7s-colibri-aster.dts
+++ b/arch/arm/boot/dts/imx7s-colibri-aster.dts
@@ -1,6 +1,6 @@
-// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
 /*
- * Copyright 2017-2020 Toradex AG
+ * Copyright 2017-2022 Toradex
  *
  */
 
@@ -10,6 +10,27 @@
 
 / {
 	model = "Toradex Colibri iMX7S on Aster Carrier Board";
-	compatible = "toradex,colibri-imx7s-aster", "toradex,colibri-imx7s",
+	compatible = "toradex,colibri-imx7s-aster",
+		     "toradex,colibri-imx7s",
 		     "fsl,imx7s";
 };
+
+&ad7879_ts {
+	status = "okay";
+};
+
+&atmel_mxt_ts {
+	status = "okay";
+};
+
+&backlight {
+	status = "okay";
+};
+
+&lcdif {
+	status = "okay";
+};
+
+&panel_dpi {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx7s-colibri-eval-v3.dts b/arch/arm/boot/dts/imx7s-colibri-eval-v3.dts
index aa70d3f2e2e2..38de76630d6a 100644
--- a/arch/arm/boot/dts/imx7s-colibri-eval-v3.dts
+++ b/arch/arm/boot/dts/imx7s-colibri-eval-v3.dts
@@ -1,6 +1,6 @@
-// SPDX-License-Identifier: GPL-2.0+ OR MIT
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
 /*
- * Copyright 2016-2020 Toradex
+ * Copyright 2016-2022 Toradex
  */
 
 /dts-v1/;
@@ -9,6 +9,43 @@
 
 / {
 	model = "Toradex Colibri iMX7S on Colibri Evaluation Board V3";
-	compatible = "toradex,colibri-imx7s-eval-v3", "toradex,colibri-imx7s",
+	compatible = "toradex,colibri-imx7s-eval-v3",
+		     "toradex,colibri-imx7s",
 		     "fsl,imx7s";
 };
+
+&ad7879_ts {
+	status = "okay";
+};
+
+/*
+ * The Atmel maxtouch controller uses SODIMM 28/30, also used for PWM<B>, PWM<C>, aka pwm2, pwm3.
+ * So if you enable following capacitive touch controller, disable pwm2/pwm3 first.
+ */
+&atmel_mxt_ts {
+	status = "disabled";
+};
+
+&backlight {
+	status = "okay";
+};
+
+&lcdif {
+	status = "okay";
+};
+
+&panel_dpi {
+	status = "okay";
+};
+
+/* Colibri PWM<B> */
+&pwm2 {
+	/* The pwm2 should be disabled to enable atmel_mxt_ts touchscreen for adapter. */
+	status = "okay";
+};
+
+/* Colibri PWM<C> */
+&pwm3 {
+	/* The pwm3 should be disabled to enable atmel_mxt_ts touchscreen for adapter. */
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx7s-colibri-iris-v2.dts b/arch/arm/boot/dts/imx7s-colibri-iris-v2.dts
new file mode 100644
index 000000000000..72b5c17ab1ab
--- /dev/null
+++ b/arch/arm/boot/dts/imx7s-colibri-iris-v2.dts
@@ -0,0 +1,78 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/dts-v1/;
+#include "imx7s-colibri.dtsi"
+#include "imx7-colibri-iris-v2.dtsi"
+
+/ {
+	model = "Toradex Colibri iMX7S on Iris V2 Carrier Board";
+	compatible = "toradex,colibri-imx7s-iris-v2",
+		     "toradex,colibri-imx7s",
+		     "fsl,imx7s";
+};
+
+&ad7879_ts {
+	status = "okay";
+};
+
+&atmel_mxt_ts {
+	status = "okay";
+};
+
+&backlight {
+	status = "okay";
+};
+
+&gpio2 {
+	/*
+	 * This switches the LVDS transceiver to VESA color mapping mode.
+	 */
+	lvds-color-map-hog {
+		gpio-hog;
+		gpios = <13 GPIO_ACTIVE_HIGH>; /* SODIMM 95 */
+		line-name = "LVDS_COLOR_MAP";
+		output-low;
+	};
+};
+
+&gpio7 {
+	/*
+	 * This switches the LVDS transceiver to the 24-bit RGB mode.
+	 */
+	lvds-rgb-mode-hog {
+		gpio-hog;
+		gpios = <2 GPIO_ACTIVE_HIGH>; /* SODIMM 63 */
+		line-name = "LVDS_RGB_MODE";
+		output-low;
+	};
+
+	/*
+	 * This switches the LVDS transceiver to the single-channel
+	 * output mode.
+	 */
+	lvds-ch-mode-hog {
+		gpio-hog;
+		gpios = <3 GPIO_ACTIVE_HIGH>; /* SODIMM 55 */
+		line-name = "LVDS_CH_MODE";
+		output-high;
+	};
+
+	/* This turns the LVDS transceiver on */
+	lvds-power-on-hog {
+		gpio-hog;
+		gpios = <11 GPIO_ACTIVE_HIGH>; /* SODIMM 99 */
+		line-name = "LVDS_POWER_ON";
+		output-high;
+	};
+};
+
+&lcdif {
+	status = "okay";
+};
+
+&panel_dpi {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx7s-colibri-iris.dts b/arch/arm/boot/dts/imx7s-colibri-iris.dts
new file mode 100644
index 000000000000..26ba72c17feb
--- /dev/null
+++ b/arch/arm/boot/dts/imx7s-colibri-iris.dts
@@ -0,0 +1,51 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/dts-v1/;
+#include "imx7s-colibri.dtsi"
+#include "imx7-colibri-iris.dtsi"
+
+/ {
+	model = "Toradex Colibri iMX7S on Iris Carrier Board";
+	compatible = "toradex,colibri-imx7s-iris",
+		     "toradex,colibri-imx7s",
+		     "fsl,imx7s";
+};
+
+&ad7879_ts {
+	status = "okay";
+};
+
+/*
+ * The Atmel maxtouch controller uses SODIMM 28/30, also used for PWM<B>, PWM<C>, aka pwm2, pwm3.
+ * So if you enable following capacitive touch controller, disable pwm2/pwm3 first.
+ */
+&atmel_mxt_ts {
+	status = "disabled";
+};
+
+&backlight {
+	status = "okay";
+};
+
+&lcdif {
+	status = "okay";
+};
+
+&panel_dpi {
+	status = "okay";
+};
+
+/* Colibri PWM<B> */
+&pwm2 {
+	/* The pwm2 should be disabled to enable atmel_mxt_ts touchscreen for adapter. */
+	status = "okay";
+};
+
+/* Colibri PWM<C> */
+&pwm3 {
+	/* The pwm3 should be disabled to enable atmel_mxt_ts touchscreen for adapter. */
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imx7s-colibri.dtsi b/arch/arm/boot/dts/imx7s-colibri.dtsi
index 94de220a5965..ef51395d3537 100644
--- a/arch/arm/boot/dts/imx7s-colibri.dtsi
+++ b/arch/arm/boot/dts/imx7s-colibri.dtsi
@@ -1,6 +1,6 @@
-// SPDX-License-Identifier: GPL-2.0+ OR MIT
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
 /*
- * Copyright 2016-2020 Toradex
+ * Copyright 2016-2022 Toradex
  */
 
 #include "imx7s.dtsi"
@@ -13,6 +13,7 @@
 	};
 };
 
+/* NAND */
 &gpmi {
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/imx7s-warp.dts b/arch/arm/boot/dts/imx7s-warp.dts
index 569bbd84e371..e8734d218b9d 100644
--- a/arch/arm/boot/dts/imx7s-warp.dts
+++ b/arch/arm/boot/dts/imx7s-warp.dts
@@ -75,7 +75,7 @@
 
 		dailink_master: simple-audio-card,codec {
 			sound-dai = <&codec>;
-			clocks = <&clks IMX7D_AUDIO_MCLK_ROOT_CLK>;
+			clocks = <&clks IMX7D_AUDIO_MCLK_ROOT_DIV>;
 		};
 	};
 };
@@ -232,7 +232,7 @@
 		#sound-dai-cells = <0>;
 		reg = <0x0a>;
 		compatible = "fsl,sgtl5000";
-		clocks = <&clks IMX7D_AUDIO_MCLK_ROOT_CLK>;
+		clocks = <&clks IMX7D_AUDIO_MCLK_ROOT_DIV>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_sai1_mclk>;
 		VDDA-supply = <&vgen4_reg>;
@@ -248,17 +248,17 @@
 
 &mipi_csi {
 	clock-frequency = <166000000>;
-	fsl,csis-hs-settle = <3>;
 	status = "okay";
 
-	port@0 {
-		reg = <0>;
+	ports {
+		port@0 {
+			reg = <0>;
 
-		mipi_from_sensor: endpoint {
-			remote-endpoint = <&ov2680_to_mipi>;
-			data-lanes = <1>;
+			mipi_from_sensor: endpoint {
+				remote-endpoint = <&ov2680_to_mipi>;
+				data-lanes = <1>;
+			};
 		};
-
 	};
 };
 
diff --git a/arch/arm/boot/dts/imx7s.dtsi b/arch/arm/boot/dts/imx7s.dtsi
index 1843fc053870..0fc9e6b8b05d 100644
--- a/arch/arm/boot/dts/imx7s.dtsi
+++ b/arch/arm/boot/dts/imx7s.dtsi
@@ -76,6 +76,22 @@
 			clock-latency = <61036>; /* two CLK32 periods */
 			clocks = <&clks IMX7D_CLK_ARM>;
 			cpu-idle-states = <&cpu_sleep_wait>;
+			operating-points-v2 = <&cpu0_opp_table>;
+			#cooling-cells = <2>;
+			nvmem-cells = <&fuse_grade>;
+			nvmem-cell-names = "speed_grade";
+		};
+	};
+
+	cpu0_opp_table: opp-table {
+		compatible = "operating-points-v2";
+		opp-shared;
+
+		opp-792000000 {
+			opp-hz = /bits/ 64 <792000000>;
+			opp-microvolt = <1000000>;
+			clock-latency-ns = <150000>;
+			opp-supported-hw = <0xf>, <0xf>;
 		};
 	};
 
@@ -104,6 +120,7 @@
 		compatible = "usb-nop-xceiv";
 		clocks = <&clks IMX7D_USB_HSIC_ROOT_CLK>;
 		clock-names = "main_clk";
+		power-domains = <&pgc_hsic_phy>;
 		#phy-cells = <0>;
 	};
 
@@ -159,7 +176,7 @@
 			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>;
 	};
 
-	soc {
+	soc: soc {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "simple-bus";
@@ -430,7 +447,7 @@
 				status = "disabled";
 			};
 
-			iomuxc_lpsr: iomuxc-lpsr@302c0000 {
+			iomuxc_lpsr: pinctrl@302c0000 {
 				compatible = "fsl,imx7d-iomuxc-lpsr";
 				reg = <0x302c0000 0x10000>;
 				fsl,input-sel = <&iomuxc>;
@@ -809,8 +826,6 @@
 			mipi_csi: mipi-csi@30750000 {
 				compatible = "fsl,imx7-mipi-csi2";
 				reg = <0x30750000 0x10000>;
-				#address-cells = <1>;
-				#size-cells = <0>;
 				interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clks IMX7D_IPG_ROOT_CLK>,
 					 <&clks IMX7D_MIPI_CSI_ROOT_CLK>,
@@ -819,18 +834,22 @@
 				power-domains = <&pgc_mipi_phy>;
 				phy-supply = <&reg_1p0d>;
 				resets = <&src IMX7_RESET_MIPI_PHY_MRST>;
-				reset-names = "mrst";
 				status = "disabled";
 
-				port@0 {
-					reg = <0>;
-				};
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
 
-				port@1 {
-					reg = <1>;
+					port@0 {
+						reg = <0>;
+					};
 
-					mipi_vc0_to_csi_mux: endpoint {
-						remote-endpoint = <&csi_mux_from_mipi_vc0>;
+					port@1 {
+						reg = <1>;
+
+						mipi_vc0_to_csi_mux: endpoint {
+							remote-endpoint = <&csi_mux_from_mipi_vc0>;
+						};
 					};
 				};
 			};
@@ -1135,7 +1154,6 @@
 				compatible = "fsl,imx7d-usb", "fsl,imx27-usb";
 				reg = <0x30b30000 0x200>;
 				interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
-				power-domains = <&pgc_hsic_phy>;
 				clocks = <&clks IMX7D_USB_CTRL_CLK>;
 				fsl,usbphy = <&usbphynop3>;
 				fsl,usbmisc = <&usbmisc3 0>;
@@ -1206,7 +1224,7 @@
 				status = "disabled";
 			};
 
-			sdma: sdma@30bd0000 {
+			sdma: dma-controller@30bd0000 {
 				compatible = "fsl,imx7d-sdma", "fsl,imx35-sdma";
 				reg = <0x30bd0000 0x10000>;
 				interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
diff --git a/arch/arm/boot/dts/imx7ulp.dtsi b/arch/arm/boot/dts/imx7ulp.dtsi
index b7ea37ad4e55..7f7d2d5122fb 100644
--- a/arch/arm/boot/dts/imx7ulp.dtsi
+++ b/arch/arm/boot/dts/imx7ulp.dtsi
@@ -259,7 +259,7 @@
 			interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&pcc2 IMX7ULP_CLK_WDG1>;
 			assigned-clocks = <&pcc2 IMX7ULP_CLK_WDG1>;
-			assigned-clocks-parents = <&scg1 IMX7ULP_CLK_FIRC_BUS_CLK>;
+			assigned-clock-parents = <&scg1 IMX7ULP_CLK_FIRC_BUS_CLK>;
 			timeout-sec = <40>;
 		};
 
@@ -328,8 +328,9 @@
 			compatible = "fsl,imx7ulp-lpi2c";
 			reg = <0x40a40000 0x10000>;
 			interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&pcc3 IMX7ULP_CLK_LPI2C6>;
-			clock-names = "ipg";
+			clocks = <&pcc3 IMX7ULP_CLK_LPI2C6>,
+				 <&scg1 IMX7ULP_CLK_NIC1_BUS_DIV>;
+			clock-names = "per", "ipg";
 			assigned-clocks = <&pcc3 IMX7ULP_CLK_LPI2C6>;
 			assigned-clock-parents = <&scg1 IMX7ULP_CLK_FIRC>;
 			assigned-clock-rates = <48000000>;
@@ -340,8 +341,9 @@
 			compatible = "fsl,imx7ulp-lpi2c";
 			reg = <0x40a50000 0x10000>;
 			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&pcc3 IMX7ULP_CLK_LPI2C7>;
-			clock-names = "ipg";
+			clocks = <&pcc3 IMX7ULP_CLK_LPI2C7>,
+				 <&scg1 IMX7ULP_CLK_NIC1_BUS_DIV>;
+			clock-names = "per", "ipg";
 			assigned-clocks = <&pcc3 IMX7ULP_CLK_LPI2C7>;
 			assigned-clock-parents = <&scg1 IMX7ULP_CLK_FIRC>;
 			assigned-clock-rates = <48000000>;
diff --git a/arch/arm/boot/dts/imxrt1050-evk.dts b/arch/arm/boot/dts/imxrt1050-evk.dts
new file mode 100644
index 000000000000..6a9c10decf52
--- /dev/null
+++ b/arch/arm/boot/dts/imxrt1050-evk.dts
@@ -0,0 +1,72 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2019
+ * Author(s): Giulio Benetti <giulio.benetti@benettiengineering.com>
+ */
+
+/dts-v1/;
+#include "imxrt1050.dtsi"
+#include "imxrt1050-pinfunc.h"
+
+/ {
+	model = "NXP IMXRT1050-evk board";
+	compatible = "fsl,imxrt1050-evk", "fsl,imxrt1050";
+
+	chosen {
+		stdout-path = &lpuart1;
+	};
+
+	aliases {
+		gpio0 = &gpio1;
+		gpio1 = &gpio2;
+		gpio2 = &gpio3;
+		gpio3 = &gpio4;
+		gpio4 = &gpio5;
+		mmc0 = &usdhc1;
+		serial0 = &lpuart1;
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x2000000>;
+	};
+};
+
+&lpuart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_lpuart1>;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl_lpuart1: lpuart1grp {
+		fsl,pins = <
+			MXRT1050_IOMUXC_GPIO_AD_B0_12_LPUART1_TXD	0xf1
+			MXRT1050_IOMUXC_GPIO_AD_B0_13_LPUART1_RXD	0xf1
+		>;
+	};
+
+	pinctrl_usdhc0: usdhc0grp {
+		fsl,pins = <
+			MXRT1050_IOMUXC_GPIO_B1_12_USDHC1_CD_B		0x1B000
+			MXRT1050_IOMUXC_GPIO_B1_14_USDHC1_VSELECT	0xB069
+			MXRT1050_IOMUXC_GPIO_SD_B0_00_USDHC1_CMD	0x17061
+			MXRT1050_IOMUXC_GPIO_SD_B0_01_USDHC1_CLK	0x17061
+			MXRT1050_IOMUXC_GPIO_SD_B0_05_USDHC1_DATA3	0x17061
+			MXRT1050_IOMUXC_GPIO_SD_B0_04_USDHC1_DATA2	0x17061
+			MXRT1050_IOMUXC_GPIO_SD_B0_03_USDHC1_DATA1	0x17061
+			MXRT1050_IOMUXC_GPIO_SD_B0_02_USDHC1_DATA0	0x17061
+		>;
+	};
+};
+
+&usdhc1 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz", "sleep";
+	pinctrl-0 = <&pinctrl_usdhc0>;
+	pinctrl-1 = <&pinctrl_usdhc0>;
+	pinctrl-2 = <&pinctrl_usdhc0>;
+	pinctrl-3 = <&pinctrl_usdhc0>;
+	cd-gpios = <&gpio2 28 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/imxrt1050-pinfunc.h b/arch/arm/boot/dts/imxrt1050-pinfunc.h
new file mode 100644
index 000000000000..22c14a3262ad
--- /dev/null
+++ b/arch/arm/boot/dts/imxrt1050-pinfunc.h
@@ -0,0 +1,993 @@
+/* SPDX-License-Identifier: (GPL-2.0+ OR MIT) */
+/*
+ * Copyright (C) 2019
+ * Author(s): Giulio Benetti <giulio.benetti@benettiengineering.com>
+ */
+
+#ifndef _DT_BINDINGS_PINCTRL_IMXRT1050_PINFUNC_H
+#define _DT_BINDINGS_PINCTRL_IMXRT1050_PINFUNC_H
+
+#define IMX_PAD_SION	0x40000000
+
+/*
+ * The pin function ID is a tuple of
+ * <mux_reg conf_reg input_reg mux_mode input_val>
+ */
+
+#define MXRT1050_IOMUXC_GPIO_EMC_00_SEMC_DA00				0x014 0x204 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_00_FLEXPWM4_PWM0_A			0x014 0x204 0x494 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_00_LPSPI2_SCK				0x014 0x204 0x500 0x2 0x1
+#define MXRT1050_IOMUXC_GPIO_EMC_00_XBAR_INOUT2				0x014 0x204 0x60C 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_00_FLEXIO1_D00				0x014 0x204 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_00_GPIO4_IO00				0x014 0x204 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_EMC_01_SEMC_DA01				0x018 0x208 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_01_FLEXPWM4_PWM0_B			0x018 0x208 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_01_LPSPI2_PCS0				0x018 0x208 0x4FC 0x2 0x1
+#define MXRT1050_IOMUXC_GPIO_EMC_01_XBAR_INOUT3				0x018 0x208 0x610 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_01_FLEXIO1_D01				0x018 0x208 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_01_GPIO4_IO01				0x018 0x208 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_EMC_02_SEMC_DA02				0x01C 0x20C 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_02_FLEXPWM4_PWM1_A			0x01C 0x20C 0x498 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_02_LPSPI2_SDO				0x01C 0x20C 0x508 0x2 0x1
+#define MXRT1050_IOMUXC_GPIO_EMC_02_XBAR_INOUT4				0x01C 0x20C 0x614 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_02_FLEXIO1_D02				0x01C 0x20C 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_02_GPIO4_IO02				0x01C 0x20C 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_EMC_03_SEMC_DA03				0x020 0x210 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_03_FLEXPWM4_PWM1_B			0x020 0x210 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_03_LPSPI2_SDI				0x020 0x210 0x504 0x2 0x1
+#define MXRT1050_IOMUXC_GPIO_EMC_03_XBAR_INOUT5				0x020 0x210 0x618 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_03_FLEXIO1_D03				0x020 0x210 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_03_GPIO4_IO03				0x020 0x210 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_EMC_04_SEMC_DA04				0x024 0x214 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_04_FLEXPWM4_PWM2_A			0x024 0x214 0x49C 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_04_SAI2_TX_DATA			0x024 0x214 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_04_XBAR_INOUT6				0x024 0x214 0x61C 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_04_FLEXIO1_D04				0x024 0x214 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_04_GPIO4_IO04				0x024 0x214 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_EMC_05_SEMC_DA05				0x028 0x218 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_05_FLEXPWM4_PWM2_B			0x028 0x218 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_05_SAI2_TX_SYNC			0x028 0x218 0x5C4 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_05_XBAR_INOUT7				0x028 0x218 0x620 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_05_FLEXIO1_D05				0x028 0x218 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_05_GPIO4_IO05				0x028 0x218 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_EMC_06_SEMC_DA06				0x02C 0x21C 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_06_FLEXPWM2_PWM0_A			0x02C 0x21C 0x478 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_06_SAI2_TX_BCLK			0x02C 0x21C 0x5C0 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_06_XBAR_INOUT8				0x02C 0x21C 0x624 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_06_FLEXIO1_D06				0x02C 0x21C 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_06_GPIO4_IO06				0x02C 0x21C 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_EMC_07_SEMC_DA07				0x030 0x220 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_07_FLEXPWM2_PWM0_B			0x030 0x220 0x488 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_07_SAI2_MCLK				0x030 0x220 0x5B0 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_07_XBAR_INOUT9				0x030 0x220 0x628 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_07_FLEXIO1_D07				0x030 0x220 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_07_GPIO4_IO07				0x030 0x220 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_EMC_08_SEMC_DM00				0x034 0x224 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_08_FLEXPWM2_PWM1_A			0x034 0x224 0x47C 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_08_SAI2_RX_DATA			0x034 0x224 0x5B8 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_08_XBAR_INOUT17			0x034 0x224 0x62C 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_08_FLEXIO1_D08				0x034 0x224 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_08_GPIO4_IO08				0x034 0x224 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_EMC_09_SEMC_ADDR00				0x038 0x228 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_09_FLEXPWM2_PWM1_B			0x038 0x228 0x48C 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_09_SAI2_RX_SYNC			0x038 0x228 0x5BC 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_09_FLEXCAN2_TX				0x038 0x228 0x000 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_09_FLEXIO1_D09				0x038 0x228 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_09_GPIO4_IO09				0x038 0x228 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_EMC_10_SEMC_ADDR01				0x03C 0x22C 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_10_FLEXPWM2_PWM2_A			0x03C 0x22C 0x480 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_10_SAI2_RX_BCLK			0x03C 0x22C 0x5B4 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_10_FLEXCAN2_RX				0x03C 0x22C 0x450 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_10_FLEXIO1_D10				0x03C 0x22C 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_10_GPIO4_IO10				0x03C 0x22C 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_EMC_11_SEMC_ADDR02				0x040 0x230 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_11_FLEXPWM2_PWM2_B			0x040 0x230 0x490 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_11_LPI2C4_SDA				0x040 0x230 0x4E8 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_11_USDHC2_RESET_B			0x040 0x230 0x000 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_11_FLEXIO1_D11				0x040 0x230 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_11_GPIO4_IO11				0x040 0x230 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_EMC_12_SEMC_ADDR03				0x044 0x234 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_12_XBAR_INOUT24			0x044 0x234 0x640 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_12_LPI2C4_SCL				0x044 0x234 0x4E4 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_12_USDHC2_WP				0x044 0x234 0x5D8 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_12_FLEXPWM1_PWM3_A			0x044 0x234 0x454 0x4 0x1
+#define MXRT1050_IOMUXC_GPIO_EMC_12_GPIO4_IO12				0x044 0x234 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_EMC_13_SEMC_ADDR04				0x048 0x238 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_13_XBAR_INOUT25			0x048 0x238 0x650 0x1 0x1
+#define MXRT1050_IOMUXC_GPIO_EMC_13_LPUART3_TXD				0x048 0x238 0x53C 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_13_MQS_RIGHT				0x048 0x238 0x000 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_13_FLEXPWM1_PWM3_B			0x048 0x238 0x464 0x4 0x1
+#define MXRT1050_IOMUXC_GPIO_EMC_13_GPIO4_IO13				0x048 0x238 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_EMC_14_SEMC_ADDR05				0x04C 0x23C 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_14_XBAR_INOUT19			0x04C 0x23C 0x654 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_14_LPUART3_RXD				0x04C 0x23C 0x538 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_14_MQS_LEFT				0x04C 0x23C 0x000 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_14_LPSPI2_PCS1				0x04C 0x23C 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_14_GPIO4_IO14				0x04C 0x23C 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_EMC_15_SEMC_ADDR06				0x050 0x240 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_15_XBAR_INOUT20			0x050 0x240 0x634 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_15_LPUART3_CTS_B			0x050 0x240 0x534 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_15_SPDIF_OUT				0x050 0x240 0x000 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_15_TMR3_TIMER0				0x050 0x240 0x57C 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_15_GPIO4_IO15				0x050 0x240 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_EMC_16_SEMC_ADDR07				0x054 0x244 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_16_XBAR_INOUT21			0x054 0x244 0x658 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_16_LPUART3_RTS_B			0x054 0x244 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_16_SPDIF_IN				0x054 0x244 0x5C8 0x3 0x1
+#define MXRT1050_IOMUXC_GPIO_EMC_16_TMR3_TIMER1				0x054 0x244 0x580 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_16_GPIO4_IO16				0x054 0x244 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_EMC_17_SEMC_ADDR08				0x058 0x248 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_17_FLEXPWM4_PWM3_A			0x058 0x248 0x4A0 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_17_LPUART4_CTS_B			0x058 0x248 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_17_FLEXCAN1_TX				0x058 0x248 0x000 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_17_TMR3_TIMER2				0x058 0x248 0x584 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_17_GPIO4_IO17				0x058 0x248 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_EMC_18_SEMC_ADDR09				0x05C 0x24C 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_18_FLEXPWM4_PWM3_B			0x05C 0x24C 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_18_LPUART4_RTS_B			0x05C 0x24C 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_18_FLEXCAN1_RX				0x05C 0x24C 0x44C 0x3 0x1
+#define MXRT1050_IOMUXC_GPIO_EMC_18_TMR3_TIMER3				0x05C 0x24C 0x588 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_18_GPIO4_IO18				0x05C 0x24C 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_18_SNVS_VIO_5_CTL			0x05C 0x24C 0x000 0x6 0x0
+
+#define MXRT1050_IOMUXC_GPIO_EMC_19_SEMC_ADDR11				0x060 0x250 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_19_FLEXPWM2_PWM3_A			0x060 0x250 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_19_LPUART4_TXD				0x060 0x250 0x544 0x2 0x1
+#define MXRT1050_IOMUXC_GPIO_EMC_19_ENET_RX_DATA01			0x060 0x250 0x438 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_19_TMR2_TIMER0				0x060 0x250 0x56C 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_19_GPIO4_IO19				0x060 0x250 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_19_SNVS_VIO_5				0x060 0x250 0x000 0x6 0x0
+
+#define MXRT1050_IOMUXC_GPIO_EMC_20_SEMC_ADDR12				0x064 0x254 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_20_FLEXPWM2_PWM3_B			0x064 0x254 0x484 0x1 0x1
+#define MXRT1050_IOMUXC_GPIO_EMC_20_LPUART4_RXD				0x064 0x254 0x540 0x2 0x1
+#define MXRT1050_IOMUXC_GPIO_EMC_20_ENET_RX_DATA00			0x064 0x254 0x434 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_20_TMR2_TIMER0				0x064 0x254 0x570 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_20_GPIO4_IO20				0x064 0x254 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_EMC_21_SEMC_BA0				0x068 0x258 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_21_FLEXPWM3_PWM3_A			0x068 0x258 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_21_LPI2C3_SDA				0x068 0x258 0x4E0 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_21_ENET_TX_DATA01			0x068 0x258 0x000 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_21_TMR2_TIMER2				0x068 0x258 0x574 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_21_GPIO4_IO21				0x068 0x258 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_EMC_22_SEMC_BA1				0x06C 0x25C 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_22_FLEXPWM3_PWM3_B			0x06C 0x25C 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_22_LPI2C3_SCL				0x06C 0x25C 0x4DC 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_22_ENET_TX_DATA00			0x06C 0x25C 0x000 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_22_TMR2_TIMER3				0x06C 0x25C 0x578 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_22_GPIO4_IO22				0x06C 0x25C 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_EMC_23_SEMC_ADDR10				0x070 0x260 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_23_FLEXPWM1_PWM0_A			0x070 0x260 0x458 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_23_LPUART5_TXD				0x070 0x260 0x54C 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_23_ENET_RX_EN				0x070 0x260 0x43C 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_23_GPT1_CAPTURE2			0x070 0x260 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_23_GPIO4_IO23				0x070 0x260 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_EMC_24_SEMC_CAS				0x074 0x264 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_24_FLEXPWM1_PWM0_B			0x074 0x264 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_24_LPUART5_RXD				0x074 0x264 0x548 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_24_ENET_TX_EN				0x074 0x264 0x000 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_24_GPT1_CAPTURE1			0x074 0x264 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_24_GPIO4_IO24				0x074 0x264 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_EMC_25_SEMC_RAS				0x078 0x268 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_25_FLEXPWM1_PWM1_A			0x078 0x268 0x45C 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_25_LPUART6_TXD				0x078 0x268 0x554 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_25_ENET_TX_CLK				0x078 0x268 0x448 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_25_ENET_REF_CLK			0x078 0x268 0x42C 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_25_GPIO4_IO25				0x078 0x268 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_EMC_26_SEMC_CLK				0x07C 0x26C 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_26_FLEXPWM1_PWM1_B			0x07C 0x26C 0x46C 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_26_LPUART6_RXD				0x07C 0x26C 0x550 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_26_ENET_RX_ER				0x07C 0x26C 0x440 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_26_FLEXIO1_D12				0x07C 0x26C 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_26_GPIO4_IO26				0x07C 0x26C 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_EMC_27_SEMC_CKE				0x080 0x270 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_27_FLEXPWM1_PWM2_A			0x080 0x270 0x460 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_27_LPUART5_RTS_B			0x080 0x270 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_27_LPSPI1_SCK				0x080 0x270 0x4F0 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_27_FLEXIO1_D13				0x080 0x270 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_27_GPIO4_IO27				0x080 0x270 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_EMC_28_SEMC_WE				0x084 0x274 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_28_FLEXPWM1_PWM2_B			0x084 0x274 0x470 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_28_LPUART5_CTS_B			0x084 0x274 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_28_LPSPI1_SDO				0x084 0x274 0x4F8 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_28_FLEXIO1_D14				0x084 0x274 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_28_GPIO4_IO28				0x084 0x274 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_EMC_29_SEMC_CS0				0x088 0x278 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_29_FLEXPWM3_PWM0_A			0x088 0x278 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_29_LPUART6_RTS_B			0x088 0x278 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_29_LPSPI1_SDI				0x088 0x278 0x4F4 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_29_FLEXIO1_D15				0x088 0x278 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_29_GPIO4_IO29				0x088 0x278 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_EMC_30_SEMC_DA08				0x08C 0x27C 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_30_FLEXPWM3_PWM0_B			0x08C 0x27C 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_30_LPUART6_CTS_B			0x08C 0x27C 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_30_LPSPI1_PCS0				0x08C 0x27C 0x4EC 0x3 0x1
+#define MXRT1050_IOMUXC_GPIO_EMC_30_CSI_DATA23				0x08C 0x27C 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_30_GPIO4_IO30				0x08C 0x27C 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_EMC_31_SEMC_DA09				0x090 0x280 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_31_FLEXPWM3_PWM1_A			0x090 0x280 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_31_LPUART7_TXD				0x090 0x280 0x55C 0x2 0x1
+#define MXRT1050_IOMUXC_GPIO_EMC_31_LPSPI1_PCS1				0x090 0x280 0x000 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_31_CSI_DATA22				0x090 0x280 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_31_GPIO4_IO31				0x090 0x280 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_EMC_32_SEMC_DA10				0x094 0x284 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_32_FLEXPWM3_PWM1_B			0x094 0x284 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_32_LPUART7_RXD				0x094 0x284 0x558 0x2 0x1
+#define MXRT1050_IOMUXC_GPIO_EMC_32_CCM_PMIC_READY			0x094 0x284 0x3FC 0x3 0x4
+#define MXRT1050_IOMUXC_GPIO_EMC_32_CSI_DATA21				0x094 0x284 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_32_GPIO3_IO18				0x094 0x284 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_EMC_33_SEMC_DA11				0x098 0x288 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_33_FLEXPWM3_PWM2_A			0x098 0x288 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_33_USDHC1_RESET_B			0x098 0x288 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_33_SAI3_RX_DATA			0x098 0x288 0x000 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_33_CSI_DATA20				0x098 0x288 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_33_GPIO3_IO19				0x098 0x288 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_EMC_34_SEMC_DA12				0x09C 0x28C 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_34_FLEXPWM3_PWM2_B			0x09C 0x28C 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_34_USDHC1_VSELECT			0x09C 0x28C 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_34_SAI3_RX_SYNC			0x09C 0x28C 0x000 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_34_CSI_DATA19				0x09C 0x28C 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_34_GPIO3_IO20				0x09C 0x28C 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_EMC_35_SEMC_DA13				0x0A0 0x290 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_35_XBAR_INOUT18			0x0A0 0x290 0x630 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_35_GPT1_COMPARE1			0x0A0 0x290 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_35_SAI3_RX_BCLK			0x0A0 0x290 0x000 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_35_CSI_DATA18				0x0A0 0x290 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_35_GPIO3_IO21				0x0A0 0x290 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_35_USDHC1_CD_B				0x0A0 0x290 0x5D4 0x6 0x0
+
+#define MXRT1050_IOMUXC_GPIO_EMC_36_SEMC_DA14				0x0A4 0x294 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_36_XBAR_INOUT22			0x0A4 0x294 0x638 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_36_GPT1_COMPARE2			0x0A4 0x294 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_36_SAI3_TX_DATA			0x0A4 0x294 0x000 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_36_CSI_DATA17				0x0A4 0x294 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_36_GPIO3_IO22				0x0A4 0x294 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_36_USDHC1_WP				0x0A4 0x294 0x5D8 0x6 0x1
+
+#define MXRT1050_IOMUXC_GPIO_EMC_37_SEMC_DA15				0x0A8 0x298 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_37_XBAR_INOUT23			0x0A8 0x298 0x63C 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_37_GPT1_COMPARE3			0x0A8 0x298 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_37_SAI3_MCLK				0x0A8 0x298 0x000 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_37_CSI_DATA16				0x0A8 0x298 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_37_GPIO3_IO23				0x0A8 0x298 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_37_USDHC2_WP				0x0A8 0x298 0x608 0x6 0x0
+
+#define MXRT1050_IOMUXC_GPIO_EMC_38_SEMC_DM01				0x0AC 0x29C 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_38_FLEXPWM1_PWM3_A			0x0AC 0x29C 0x454 0x1 0x2
+#define MXRT1050_IOMUXC_GPIO_EMC_38_LPUART8_TXD				0x0AC 0x29C 0x564 0x2 0x2
+#define MXRT1050_IOMUXC_GPIO_EMC_38_SAI3_TX_BCLK			0x0AC 0x29C 0x000 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_38_CSI_FIELD				0x0AC 0x29C 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_38_GPIO3_IO24				0x0AC 0x29C 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_38_USDHC2_VSELECT			0x0AC 0x29C 0x000 0x6 0x0
+
+#define MXRT1050_IOMUXC_GPIO_EMC_39_SEMC_DQS				0x0B0 0x2A0 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_39_FLEXPWM1_PWM3_B			0x0B0 0x2A0 0x464 0x1 0x2
+#define MXRT1050_IOMUXC_GPIO_EMC_39_LPUART8_RXD				0x0B0 0x2A0 0x560 0x2 0x2
+#define MXRT1050_IOMUXC_GPIO_EMC_39_SAI3_TX_SYNC			0x0B0 0x2A0 0x000 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_39_WDOG1_B				0x0B0 0x2A0 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_39_GPIO3_IO25				0x0B0 0x2A0 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_39_USDHC2_CD_B				0x0B0 0x2A0 0x5E0 0x6 0x1
+
+#define MXRT1050_IOMUXC_GPIO_EMC_40_SEMC_RDY				0x0B4 0x2A4 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_40_GPT2_CAPTURE2			0x0B4 0x2A4 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_40_LPSPI1_PCS2				0x0B4 0x2A4 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_40_USB_OTG2_OC				0x0B4 0x2A4 0x5CC 0x3 0x1
+#define MXRT1050_IOMUXC_GPIO_EMC_40_ENET_MDC				0x0B4 0x2A4 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_40_GPIO3_IO26				0x0B4 0x2A4 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_40_USDHC2_RESET_B			0x0B4 0x2A4 0x000 0x6 0x0
+
+#define MXRT1050_IOMUXC_GPIO_EMC_41_SEMC_CSX0				0x0B8 0x2A8 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_41_GPT2_CAPTURE1			0x0B8 0x2A8 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_41_LPSPI1_PCS3				0x0B8 0x2A8 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_41_USB_OTG2_PWR			0x0B8 0x2A8 0x000 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_41_ENET_MDIO				0x0B8 0x2A8 0x430 0x4 0x1
+#define MXRT1050_IOMUXC_GPIO_EMC_41_GPIO3_IO27				0x0B8 0x2A8 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_EMC_41_USDHC2_VSELECT			0x0B8 0x2A8 0x000 0x6 0x0
+
+#define MXRT1050_IOMUXC_GPIO_AD_B0_00_FLEXPWM2_PWM3_A			0x0BC 0x2AC 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_00_XBAR_INOUT14			0x0BC 0x2AC 0x644 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_00_REF_CLK_32K			0x0BC 0x2AC 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_00_USB_OTG2_ID			0x0BC 0x2AC 0x3F8 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_00_LPI2C1_SCLS			0x0BC 0x2AC 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_00_GPIO1_IO00			0x0BC 0x2AC 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_00_USDHC1_RESET_B			0x0BC 0x2AC 0x000 0x6 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_00_LPSPI3_SCK			0x0BC 0x2AC 0x510 0x7 0x0
+
+#define MXRT1050_IOMUXC_GPIO_AD_B0_01_FLEXPWM2_PWM3_B			0x0C0 0x2B0 0x484 0x0 0x2
+#define MXRT1050_IOMUXC_GPIO_AD_B0_01_XBAR_INOUT15			0x0C0 0x2B0 0x648 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_01_REF_CLK_24M			0x0C0 0x2B0 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_01_USB_OTG1_ID			0x0C0 0x2B0 0x3F4 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_01_LPI2C1_SDAS			0x0C0 0x2B0 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_01_GPIO1_IO01			0x0C0 0x2B0 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_01_EWM_OUT_B				0x0C0 0x2B0 0x000 0x6 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_01_LPSPI3_SDO			0x0C0 0x2B0 0x518 0x7 0x1
+
+#define MXRT1050_IOMUXC_GPIO_AD_B0_02_FLEXCAN2_TX			0x0C4 0x2B4 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_02_XBAR_INOUT16			0x0C4 0x2B4 0x64C 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_02_LPUART6_TXD			0x0C4 0x2B4 0x554 0x2 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B0_02_USB_OTG1_PWR			0x0C4 0x2B4 0x000 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_02_FLEXPWM1_PWM0_X			0x0C4 0x2B4 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_02_GPIO1_IO02			0x0C4 0x2B4 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_02_LPI2C1_HREQ			0x0C4 0x2B4 0x000 0x6 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_02_LPSPI3_SDI			0x0C4 0x2B4 0x514 0x7 0x1
+
+#define MXRT1050_IOMUXC_GPIO_AD_B0_03_FLEXCAN2_RX			0x0C8 0x2B8 0x450 0x0 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B0_03_XBAR_INOUT17			0x0C8 0x2B8 0x62C 0x1 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B0_03_LPUART6_RXD			0x0C8 0x2B8 0x550 0x2 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B0_03_USB_OTG1_OC			0x0C8 0x2B8 0x5D0 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_03_FLEXPWM1_PWM1_X			0x0C8 0x2B8 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_03_GPIO1_IO03			0x0C8 0x2B8 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_03_REF_CLK_24M			0x0C8 0x2B8 0x000 0x6 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_03_LPSPI3_PCS0			0x0C8 0x2B8 0x50C 0x7 0x0
+
+#define MXRT1050_IOMUXC_GPIO_AD_B0_04_SRC_BOOT_MODE00			0x0CC 0x2BC 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_04_MQS_RIGHT				0x0CC 0x2BC 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_04_ENET_TX_DATA03			0x0CC 0x2BC 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_04_SAI2_TX_SYNC			0x0CC 0x2BC 0x5C4 0x3 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B0_04_CSI_DATA09			0x0CC 0x2BC 0x41C 0x4 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B0_04_GPIO1_IO04			0x0CC 0x2BC 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_04_PIT_TRIGGER00			0x0CC 0x2BC 0x000 0x6 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_04_LPSPI3_PCS1			0x0CC 0x2BC 0x000 0x7 0x0
+
+#define MXRT1050_IOMUXC_GPIO_AD_B0_05_SRC_BOOT_MODE01			0x0D0 0x2C0 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_05_MQS_LEFT				0x0D0 0x2C0 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_05_ENET_TX_DATA02			0x0D0 0x2C0 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_05_SAI2_TX_BCLK			0x0D0 0x2C0 0x5C0 0x3 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B0_05_CSI_DATA08			0x0D0 0x2C0 0x418 0x4 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B0_05_GPIO1_IO05			0x0D0 0x2C0 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_05_XBAR_INOUT17			0x0D0 0x2C0 0x62C 0x6 0x2
+#define MXRT1050_IOMUXC_GPIO_AD_B0_05_LPSPI3_PCS2			0x0D0 0x2C0 0x000 0x7 0x0
+
+#define MXRT1050_IOMUXC_GPIO_AD_B0_06_JTAG_TMS				0x0D4 0x2C4 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_06_GPT2_COMPARE1			0x0D4 0x2C4 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_06_ENET_RX_CLK			0x0D4 0x2C4 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_06_SAI2_RX_BCLK			0x0D4 0x2C4 0x5B4 0x3 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B0_06_CSI_DATA07			0x0D4 0x2C4 0x414 0x4 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B0_06_GPIO1_IO06			0x0D4 0x2C4 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_06_XBAR_INOUT18			0x0D4 0x2C4 0x630 0x6 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B0_06_LPSPI3_PCS3			0x0D4 0x2C4 0x000 0x7 0x0
+
+#define MXRT1050_IOMUXC_GPIO_AD_B0_07_JTAG_TCK				0x0D8 0x2C8 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_07_GPT2_COMPARE2			0x0D8 0x2C8 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_07_ENET_TX_ER			0x0D8 0x2C8 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_07_SAI2_RX_SYNC			0x0D8 0x2C8 0x5BC 0x3 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B0_07_CSI_DATA06			0x0D8 0x2C8 0x410 0x4 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B0_07_GPIO1_IO07			0x0D8 0x2C8 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_07_XBAR_INOUT19			0x0D8 0x2C8 0x654 0x6 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B0_07_ENET_1588_EVENT3_OUT		0x0D8 0x2C8 0x000 0x7 0x0
+
+#define MXRT1050_IOMUXC_GPIO_AD_B0_08_JTAG_MOD				0x0DC 0x2CC 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_08_GPT2_COMPARE3			0x0DC 0x2CC 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_08_ENET_RX_DATA03			0x0DC 0x2CC 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_08_SAI2_RX_DATA			0x0DC 0x2CC 0x5B8 0x3 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B0_08_CSI_DATA05			0x0DC 0x2CC 0x40C 0x4 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B0_08_GPIO1_IO08			0x0DC 0x2CC 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_08_XBAR_INOUT20			0x0DC 0x2CC 0x634 0x6 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B0_08_ENET_1588_EVENT3_IN		0x0DC 0x2CC 0x000 0x7 0x0
+
+#define MXRT1050_IOMUXC_GPIO_AD_B0_09_JTAG_TDI				0x0E0 0x2D0 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_09_FLEXPWM2_PWM3_A			0x0E0 0x2D0 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_09_ENET_RX_DATA02			0x0E0 0x2D0 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_09_SAI2_TX_DATA			0x0E0 0x2D0 0x000 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_09_CSI_DATA04			0x0E0 0x2D0 0x408 0x4 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B0_09_GPIO1_IO09			0x0E0 0x2D0 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_09_XBAR_INOUT21			0x0E0 0x2D0 0x658 0x6 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B0_09_GPT2_CLK				0x0E0 0x2D0 0x000 0x7 0x0
+
+#define MXRT1050_IOMUXC_GPIO_AD_B0_10_JTAG_TDO				0x0E4 0x2D4 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_10_FLEXPWM1_PWM3_A			0x0E4 0x2D4 0x454 0x1 0x3
+#define MXRT1050_IOMUXC_GPIO_AD_B0_10_ENET_CRS				0x0E4 0x2D4 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_10_SAI2_MCLK				0x0E4 0x2D4 0x5B0 0x3 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B0_10_CSI_DATA03			0x0E4 0x2D4 0x404 0x4 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B0_10_GPIO1_IO10			0x0E4 0x2D4 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_10_XBAR_INOUT22			0x0E4 0x2D4 0x638 0x6 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B0_10_ENET_1588_EVENT0_OUT		0x0E4 0x2D4 0x000 0x7 0x0
+
+#define MXRT1050_IOMUXC_GPIO_AD_B0_11_JTAG_TRSTB			0x0E8 0x2D8 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_11_FLEXPWM1_PWM3_B			0x0E8 0x2D8 0x464 0x1 0x3
+#define MXRT1050_IOMUXC_GPIO_AD_B0_11_ENET_COL				0x0E8 0x2D8 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_11_WDOG1_B				0x0E8 0x2D8 0x000 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_11_CSI_DATA02			0x0E8 0x2D8 0x400 0x4 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B0_11_GPIO1_IO11			0x0E8 0x2D8 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_11_XBAR_INOUT23			0x0E8 0x2D8 0x63C 0x6 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B0_11_ENET_1588_EVENT0_IN		0x0E8 0x2D8 0x444 0x7 0x1
+
+#define MXRT1050_IOMUXC_GPIO_AD_B0_12_LPI2C4_SCL			0x0EC 0x2DC 0x4E4 0x0 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B0_12_CCM_PMIC_READY			0x0EC 0x2DC 0x3FC 0x1 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B0_12_LPUART1_TXD			0x0EC 0x2DC 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_12_WDOG2_B				0x0EC 0x2DC 0x000 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_12_FLEXPWM1_PWM2_X			0x0EC 0x2DC 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_12_GPIO1_IO12			0x0EC 0x2DC 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_12_ENET_1588_EVENT1_OUT		0x0EC 0x2DC 0x000 0x6 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_12_NMI				0x0EC 0x2DC 0x568 0x7 0x0
+
+#define MXRT1050_IOMUXC_GPIO_AD_B0_13_LPI2C4_SDA			0x0F0 0x2E0 0x4E8 0x0 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B0_13_GPT1_CLK				0x0F0 0x2E0 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_13_LPUART1_RXD			0x0F0 0x2E0 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_13_EWM_OUT_B				0x0F0 0x2E0 0x000 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_13_FLEXPWM1_PWM3_X			0x0F0 0x2E0 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_13_GPIO1_IO13			0x0F0 0x2E0 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_13_ENET_1588_EVENT1_IN		0x0F0 0x2E0 0x000 0x6 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_13_REF_CLK_24M			0x0F0 0x2E0 0x000 0x7 0x0
+
+#define MXRT1050_IOMUXC_GPIO_AD_B0_14_USB_OTG2_OC			0x0F4 0x2E4 0x5CC 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_14_XBAR_INOUT24			0x0F4 0x2E4 0x640 0x1 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B0_14_LPUART1_CTS_B			0x0F4 0x2E4 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_14_ENET_1588_EVENT0_OUT		0x0F4 0x2E4 0x000 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_14_CSI_VSYNC				0x0F4 0x2E4 0x428 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_14_GPIO1_IO14			0x0F4 0x2E4 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_14_FLEXCAN2_TX			0x0F4 0x2E4 0x000 0x6 0x0
+
+#define MXRT1050_IOMUXC_GPIO_AD_B0_15_USB_OTG2_PWR			0x0F8 0x2E8 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_15_XBAR_INOUT25			0x0F8 0x2E8 0x650 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_15_LPUART1_RTS_B			0x0F8 0x2E8 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_15_ENET_1588_EVENT0_IN		0x0F8 0x2E8 0x444 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_15_CSI_HSYNC				0x0F8 0x2E8 0x420 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_15_GPIO1_IO15			0x0F8 0x2E8 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B0_15_FLEXCAN2_RX			0x0F8 0x2E8 0x450 0x6 0x2
+#define MXRT1050_IOMUXC_GPIO_AD_B0_15_WDOG1_WDOG_RST_B_DEB		0x0F8 0x2E8 0x000 0x7 0x0
+
+#define MXRT1050_IOMUXC_GPIO_AD_B1_00_USB_OTG2_ID			0x0FC 0x2EC 0x3F8 0x0 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_00_TMR3_TIMER0			0x0FC 0x2EC 0x57C 0x1 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_00_LPUART2_CTS_B			0x0FC 0x2EC 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_00_LPI2C1_SCL			0x0FC 0x2EC 0x4CC 0x3 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_00_WDOG1_B				0x0FC 0x2EC 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_00_GPIO1_IO16			0x0FC 0x2EC 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_00_USDHC1_WP				0x0FC 0x2EC 0x5D8 0x6 0x2
+#define MXRT1050_IOMUXC_GPIO_AD_B1_00_KPP_ROW07				0x0FC 0x2EC 0x000 0x7 0x0
+
+#define MXRT1050_IOMUXC_GPIO_AD_B1_01_USB_OTG1_PWR			0x100 0x2F0 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_01_TMR3_TIMER1			0x100 0x2F0 0x580 0x1 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_01_LPUART2_RTS_B			0x100 0x2F0 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_01_LPI2C1_SDA			0x100 0x2F0 0x4D0 0x3 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_01_CCM_PMIC_READY			0x100 0x2F0 0x3FC 0x4 0x2
+#define MXRT1050_IOMUXC_GPIO_AD_B1_01_GPIO1_IO17			0x100 0x2F0 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_01_USDHC1_VSELECT			0x100 0x2F0 0x000 0x6 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_01_KPP_COL07				0x100 0x2F0 0x000 0x7 0x0
+
+#define MXRT1050_IOMUXC_GPIO_AD_B1_02_USB_OTG1_ID			0x104 0x2F4 0x3F4 0x0 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_02_TMR3_TIMER2			0x104 0x2F4 0x584 0x1 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_02_LPUART2_TXD			0x104 0x2F4 0x530 0x2 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_02_SPDIF_OUT				0x104 0x2F4 0x000 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_02_ENET_1588_EVENT2_OUT		0x104 0x2F4 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_02_GPIO1_IO18			0x104 0x2F4 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_02_USDHC1_CD_B			0x104 0x2F4 0x5D4 0x6 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_02_KPP_ROW06				0x104 0x2F4 0x000 0x7 0x0
+
+#define MXRT1050_IOMUXC_GPIO_AD_B1_03_USB_OTG1_OC			0x108 0x2F8 0x5D0 0x0 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_03_TMR3_TIMER3			0x108 0x2F8 0x588 0x1 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_03_LPUART2_RXD			0x108 0x2F8 0x52C 0x2 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_03_SPDIF_IN				0x108 0x2F8 0x5C8 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_03_ENET_1588_EVENT2_IN		0x108 0x2F8 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_03_GPIO1_IO19			0x108 0x2F8 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_03_USDHC2_CD_B			0x108 0x2F8 0x5E0 0x6 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_03_KPP_COL06				0x108 0x2F8 0x000 0x7 0x0
+
+#define MXRT1050_IOMUXC_GPIO_AD_B1_04_FLEXSPI_B_DATA3			0x10C 0x2FC 0x4C4 0x0 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_04_ENET_MDC				0x10C 0x2FC 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_04_LPUART3_CTS_B			0x10C 0x2FC 0x534 0x2 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_04_SPDIF_SR_CLK			0x10C 0x2FC 0x000 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_04_CSI_PIXCLK			0x10C 0x2FC 0x424 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_04_GPIO1_IO20			0x10C 0x2FC 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_04_USDHC2_DATA0			0x10C 0x2FC 0x5E8 0x6 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_04_KPP_ROW05				0x10C 0x2FC 0x000 0x7 0x0
+
+#define MXRT1050_IOMUXC_GPIO_AD_B1_05_FLEXSPI_B_DATA2			0x110 0x300 0x4C0 0x0 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_05_ENET_MDIO				0x110 0x300 0x430 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_05_LPUART3_RTS_B			0x110 0x300 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_05_SPDIF_OUT				0x110 0x300 0x000 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_05_CSI_MCLK				0x110 0x300 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_05_GPIO1_IO21			0x110 0x300 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_05_USDHC2_DATA1			0x110 0x300 0x5EC 0x6 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_05_KPP_COL05				0x110 0x300 0x000 0x7 0x0
+
+#define MXRT1050_IOMUXC_GPIO_AD_B1_06_FLEXSPI_B_DATA1			0x114 0x304 0x4BC 0x0 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_06_LPI2C3_SDA			0x114 0x304 0x4E0 0x1 0x2
+#define MXRT1050_IOMUXC_GPIO_AD_B1_06_LPUART3_TXD			0x114 0x304 0x53C 0x2 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_06_SPDIF_LOCK			0x114 0x304 0x000 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_06_CSI_VSYNC				0x114 0x304 0x428 0x4 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_06_GPIO1_IO22			0x114 0x304 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_06_USDHC2_DATA2			0x114 0x304 0x5F0 0x6 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_06_KPP_ROW04				0x114 0x304 0x000 0x7 0x0
+
+#define MXRT1050_IOMUXC_GPIO_AD_B1_07_FLEXSPI_B_DATA0			0x118 0x308 0x4B8 0x0 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_07_LPI2C3_SCL			0x118 0x308 0x4DC 0x1 0x2
+#define MXRT1050_IOMUXC_GPIO_AD_B1_07_LPUART3_RXD			0x118 0x308 0x538 0x2 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_07_SPDIF_EXT_CLK			0x118 0x308 0x000 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_07_CSI_HSYNC				0x118 0x308 0x420 0x4 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_07_GPIO1_IO23			0x118 0x308 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_07_USDHC2_DATA3			0x118 0x308 0x5F4 0x6 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_07_KPP_COL04				0x118 0x308 0x000 0x7 0x0
+
+#define MXRT1050_IOMUXC_GPIO_AD_B1_08_FLEXSPI_A_SS1_B			0x11C 0x30C 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_08_FLEXPWM4_PWM0_A			0x11C 0x30C 0x494 0x1 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_08_FLEXCAN1_TX			0x11C 0x30C 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_08_CCM_PMIC_READY			0x11C 0x30C 0x3FC 0x3 0x3
+#define MXRT1050_IOMUXC_GPIO_AD_B1_08_CSI_DATA09			0x11C 0x30C 0x41C 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_08_GPIO1_IO24			0x11C 0x30C 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_08_USDHC2_CMD			0x11C 0x30C 0x5E4 0x6 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_08_KPP_ROW03				0x11C 0x30C 0x000 0x7 0x0
+
+#define MXRT1050_IOMUXC_GPIO_AD_B1_09_FLEXSPI_A_DQS			0x120 0x310 0x4A4 0x0 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_09_FLEXPWM4_PWM1_A			0x120 0x310 0x498 0x1 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_09_FLEXCAN1_RX			0x120 0x310 0x44C 0x2 0x2
+#define MXRT1050_IOMUXC_GPIO_AD_B1_09_SAI1_MCLK				0x120 0x310 0x58C 0x3 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_09_CSI_DATA08			0x120 0x310 0x418 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_09_GPIO1_IO25			0x120 0x310 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_09_USDHC2_CLK			0x120 0x310 0x5DC 0x6 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_09_KPP_COL03				0x120 0x310 0x000 0x7 0x0
+
+#define MXRT1050_IOMUXC_GPIO_AD_B1_10_FLEXSPI_A_DATA3			0x124 0x314 0x4B4 0x0 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_10_WDOG1_B				0x124 0x314 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_10_LPUART8_TXD			0x124 0x314 0x564 0x2 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_10_SAI1_RX_SYNC			0x124 0x314 0x5A4 0x3 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_10_CSI_DATA07			0x124 0x314 0x414 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_10_GPIO1_IO26			0x124 0x314 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_10_USDHC2_WP				0x124 0x314 0x608 0x6 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_10_KPP_ROW02				0x124 0x314 0x000 0x7 0x0
+
+#define MXRT1050_IOMUXC_GPIO_AD_B1_11_FLEXSPI_A_DATA2			0x128 0x318 0x4B0 0x0 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_11_EWM_OUT_B				0x128 0x318 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_11_LPUART8_RXD			0x128 0x318 0x560 0x2 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_11_SAI1_RX_BCLK			0x128 0x318 0x590 0x3 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_11_CSI_DATA06			0x128 0x318 0x410 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_11_GPIO1_IO27			0x128 0x318 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_11_USDHC2_RESET_B			0x128 0x318 0x000 0x6 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_11_KPP_COL02				0x128 0x318 0x000 0x7 0x0
+
+#define MXRT1050_IOMUXC_GPIO_AD_B1_12_FLEXSPI_A_DATA1			0x12C 0x31C 0x4AC 0x0 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_12_ACMP1_OUT				0x12C 0x31C 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_12_LPSPI3_PCS0			0x12C 0x31C 0x50C 0x2 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_12_SAI1_RX_DATA00			0x12C 0x31C 0x594 0x3 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_12_CSI_DATA05			0x12C 0x31C 0x40C 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_12_GPIO1_IO28			0x12C 0x31C 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_12_USDHC2_DATA4			0x12C 0x31C 0x5F8 0x6 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_12_KPP_ROW01				0x12C 0x31C 0x000 0x7 0x0
+
+#define MXRT1050_IOMUXC_GPIO_AD_B1_13_FLEXSPI_A_DATA0			0x130 0x320 0x4A8 0x0 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_13_ACMP2_OUT				0x130 0x320 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_13_LPSPI3_SDI			0x130 0x320 0x514 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_13_SAI1_TX_DATA00			0x130 0x320 0x000 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_13_CSI_DATA04			0x130 0x320 0x408 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_13_GPIO1_IO29			0x130 0x320 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_13_USDHC2_DATA5			0x130 0x320 0x5FC 0x6 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_13_KPP_COL01				0x130 0x320 0x000 0x7 0x0
+
+#define MXRT1050_IOMUXC_GPIO_AD_B1_14_FLEXSPI_A_SCLK			0x134 0x324 0x4C8 0x0 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_14_ACMP3_OUT				0x134 0x324 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_14_LPSPI3_SDO			0x134 0x324 0x518 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_14_SAI1_TX_BCLK			0x134 0x324 0x5A8 0x3 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_14_CSI_DATA03			0x134 0x324 0x404 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_14_GPIO1_IO30			0x134 0x324 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_14_USDHC2_DATA6			0x134 0x324 0x600 0x6 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_14_KPP_ROW00				0x134 0x324 0x000 0x7 0x0
+
+#define MXRT1050_IOMUXC_GPIO_AD_B1_15_FLEXSPI_A_SS0_B			0x138 0x328 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_15_ACMP4_OUT				0x138 0x328 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_15_LPSPI3_SCK			0x138 0x328 0x510 0x2 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_15_SAI1_TX_SYNC			0x138 0x328 0x5AC 0x3 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_15_CSI_DATA02			0x138 0x328 0x400 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_15_GPIO1_IO31			0x138 0x328 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_AD_B1_15_USDHC2_DATA7			0x138 0x328 0x604 0x6 0x1
+#define MXRT1050_IOMUXC_GPIO_AD_B1_15_KPP_COL00				0x138 0x328 0x000 0x7 0x0
+
+#define MXRT1050_IOMUXC_GPIO_B0_00_LCD_CLK				0x13C 0x32C 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_00_TMR1_TIMER0				0x13C 0x32C 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_00_MQS_RIGHT				0x13C 0x32C 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_00_LPSPI4_PCS0				0x13C 0x32C 0x51C 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_00_FLEXIO2_D00				0x13C 0x32C 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_00_GPIO2_IO00				0x13C 0x32C 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_00_SEMC_CSX1				0x13C 0x32C 0x000 0x6 0x0
+
+#define MXRT1050_IOMUXC_GPIO_B0_01_LCD_ENABLE				0x140 0x330 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_01_TMR1_TIMER1				0x140 0x330 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_01_MQS_LEFT				0x140 0x330 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_01_LPSPI4_SDI				0x140 0x330 0x524 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_01_FLEXIO2_D01				0x140 0x330 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_01_GPIO2_IO01				0x140 0x330 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_01_SEMC_CSX2				0x140 0x330 0x000 0x6 0x0
+
+#define MXRT1050_IOMUXC_GPIO_B0_02_LCD_HSYNC				0x144 0x334 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_02_TMR1_TIMER2				0x144 0x334 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_02_FLEXCAN1_TX				0x144 0x334 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_02_LPSPI4_SDO				0x144 0x334 0x528 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_02_FLEXIO2_D02				0x144 0x334 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_02_GPIO2_IO02				0x144 0x334 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_02_SEMC_CSX3				0x144 0x334 0x000 0x6 0x0
+
+#define MXRT1050_IOMUXC_GPIO_B0_03_LCD_VSYNC				0x148 0x338 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_03_TMR2_TIMER0				0x148 0x338 0x56C 0x1 0x1
+#define MXRT1050_IOMUXC_GPIO_B0_03_FLEXCAN1_RX				0x148 0x338 0x44C 0x2 0x3
+#define MXRT1050_IOMUXC_GPIO_B0_03_LPSPI4_SCK				0x148 0x338 0x520 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_03_FLEXIO2_D03				0x148 0x338 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_03_GPIO2_IO03				0x148 0x338 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_03_WDOG2_RESET_B_DEB			0x148 0x338 0x000 0x6 0x0
+
+#define MXRT1050_IOMUXC_GPIO_B0_04_LCD_DATA00				0x14C 0x33C 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_04_TMR2_TIMER1				0x14C 0x33C 0x570 0x1 0x1
+#define MXRT1050_IOMUXC_GPIO_B0_04_LPI2C2_SCL				0x14C 0x33C 0x4D4 0x2 0x1
+#define MXRT1050_IOMUXC_GPIO_B0_04_ARM_TRACE00				0x14C 0x33C 0x000 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_04_FLEXIO2_D04				0x14C 0x33C 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_04_GPIO2_IO04				0x14C 0x33C 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_04_SRC_BT_CFG00				0x14C 0x33C 0x000 0x6 0x0
+
+#define MXRT1050_IOMUXC_GPIO_B0_05_LCD_DATA01				0x150 0x340 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_05_TMR2_TIMER2				0x150 0x340 0x574 0x1 0x1
+#define MXRT1050_IOMUXC_GPIO_B0_05_LPI2C2_SDA				0x150 0x340 0x4D8 0x2 0x1
+#define MXRT1050_IOMUXC_GPIO_B0_05_ARM_TRACE01				0x150 0x340 0x000 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_05_FLEXIO2_D05				0x150 0x340 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_05_GPIO2_IO05				0x150 0x340 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_05_SRC_BT_CFG01				0x150 0x340 0x000 0x6 0x0
+
+#define MXRT1050_IOMUXC_GPIO_B0_06_LCD_DATA02				0x154 0x344 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_06_TMR3_TIMER0				0x154 0x344 0x57C 0x1 0x2
+#define MXRT1050_IOMUXC_GPIO_B0_06_FLEXPWM2_PWM0_A			0x154 0x344 0x478 0x2 0x1
+#define MXRT1050_IOMUXC_GPIO_B0_06_ARM_TRACE02				0x154 0x344 0x000 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_06_FLEXIO2_D06				0x154 0x344 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_06_GPIO2_IO06				0x154 0x344 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_06_SRC_BT_CFG02				0x154 0x344 0x000 0x6 0x0
+
+#define MXRT1050_IOMUXC_GPIO_B0_07_LCD_DATA03				0x158 0x348 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_07_TMR3_TIMER1				0x158 0x348 0x580 0x1 0x2
+#define MXRT1050_IOMUXC_GPIO_B0_07_FLEXPWM2_PWM0_B			0x158 0x348 0x488 0x2 0x1
+#define MXRT1050_IOMUXC_GPIO_B0_07_ARM_TRACE03				0x158 0x348 0x000 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_07_FLEXIO2_D07				0x158 0x348 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_07_GPIO2_IO07				0x158 0x348 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_07_SRC_BT_CFG03				0x158 0x348 0x000 0x6 0x0
+
+#define MXRT1050_IOMUXC_GPIO_B0_08_LCD_DATA04				0x15C 0x34C 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_08_TMR3_TIMER2				0x15C 0x34C 0x584 0x1 0x2
+#define MXRT1050_IOMUXC_GPIO_B0_08_FLEXPWM2_PWM1_A			0x15C 0x34C 0x47C 0x2 0x1
+#define MXRT1050_IOMUXC_GPIO_B0_08_LPUART3_TXD				0x15C 0x34C 0x53C 0x3 0x2
+#define MXRT1050_IOMUXC_GPIO_B0_08_FLEXIO2_D08				0x15C 0x34C 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_08_GPIO2_IO08				0x15C 0x34C 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_08_SRC_BT_CFG04				0x15C 0x34C 0x000 0x6 0x0
+
+#define MXRT1050_IOMUXC_GPIO_B0_09_LCD_DATA05				0x160 0x350 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_09_TMR4_TIMER0				0x160 0x350 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_09_FLEXPWM2_PWM1_B			0x160 0x350 0x48C 0x2 0x1
+#define MXRT1050_IOMUXC_GPIO_B0_09_LPUART3_RXD				0x160 0x350 0x538 0x3 0x2
+#define MXRT1050_IOMUXC_GPIO_B0_09_FLEXIO2_D09				0x160 0x350 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_09_GPIO2_IO09				0x160 0x350 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_09_SRC_BT_CFG05				0x160 0x350 0x000 0x6 0x0
+
+#define MXRT1050_IOMUXC_GPIO_B0_10_LCD_DATA06				0x164 0x354 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_10_TMR4_TIMER1				0x164 0x354 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_10_FLEXPWM2_PWM2_A			0x164 0x354 0x480 0x2 0x1
+#define MXRT1050_IOMUXC_GPIO_B0_10_SAI1_TX_DATA03			0x164 0x354 0x598 0x3 0x1
+#define MXRT1050_IOMUXC_GPIO_B0_10_FLEXIO2_D10				0x164 0x354 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_10_GPIO2_IO10				0x164 0x354 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_10_SRC_BT_CFG06				0x164 0x354 0x000 0x6 0x0
+
+#define MXRT1050_IOMUXC_GPIO_B0_11_LCD_DATA07				0x168 0x358 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_11_TMR4_TIMER2				0x168 0x358 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_11_FLEXPWM2_PWM2_B			0x168 0x358 0x490 0x2 0x1
+#define MXRT1050_IOMUXC_GPIO_B0_11_SAI1_TX_DATA02			0x168 0x358 0x59C 0x3 0x1
+#define MXRT1050_IOMUXC_GPIO_B0_11_FLEXIO2_D11				0x168 0x358 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_11_GPIO2_IO11				0x168 0x358 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_11_SRC_BT_CFG07				0x168 0x358 0x000 0x6 0x0
+
+#define MXRT1050_IOMUXC_GPIO_B0_12_LCD_DATA08				0x16C 0x35C 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_12_XBAR_INOUT10				0x16C 0x35C 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_12_ARM_TRACE_CLK			0x16C 0x35C 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_12_SAI1_TX_DATA01			0x16C 0x35C 0x5A0 0x3 0x1
+#define MXRT1050_IOMUXC_GPIO_B0_12_FLEXIO2_D12				0x16C 0x35C 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_12_GPIO2_IO12				0x16C 0x35C 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_12_SRC_BT_CFG08				0x16C 0x35C 0x000 0x6 0x0
+
+#define MXRT1050_IOMUXC_GPIO_B0_13_LCD_DATA09				0x170 0x360 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_13_XBAR_INOUT11				0x170 0x360 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_13_ARM_TRACE_SWO			0x170 0x360 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_13_SAI1_MCLK				0x170 0x360 0x58C 0x3 0x2
+#define MXRT1050_IOMUXC_GPIO_B0_13_FLEXIO2_D13				0x170 0x360 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_13_GPIO2_IO13				0x170 0x360 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_13_SRC_BT_CFG09				0x170 0x360 0x000 0x6 0x0
+
+#define MXRT1050_IOMUXC_GPIO_B0_14_LCD_DATA10				0x174 0x364 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_14_XBAR_INOUT12				0x174 0x364 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_14_ARM_CM7_TXEV				0x174 0x364 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_14_SAI1_RX_SYNC				0x174 0x364 0x5A4 0x3 0x2
+#define MXRT1050_IOMUXC_GPIO_B0_14_FLEXIO2_D14				0x174 0x364 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_14_GPIO2_IO14				0x174 0x364 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_14_SRC_BT_CFG10				0x174 0x364 0x000 0x6 0x0
+
+#define MXRT1050_IOMUXC_GPIO_B0_15_LCD_DATA11				0x178 0x368 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_15_XBAR_INOUT13				0x178 0x368 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_15_ARM_CM7_RXEV				0x178 0x368 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_15_SAI1_RX_BCLK				0x178 0x368 0x590 0x3 0x2
+#define MXRT1050_IOMUXC_GPIO_B0_15_FLEXIO2_D15				0x178 0x368 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_15_GPIO2_IO15				0x178 0x368 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_B0_15_SRC_BT_CFG11				0x178 0x368 0x000 0x6 0x0
+
+#define MXRT1050_IOMUXC_GPIO_B1_00_LCD_DATA12				0x17C 0x36C 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_00_XBAR_INOUT14				0x17C 0x36C 0x644 0x1 0x1
+#define MXRT1050_IOMUXC_GPIO_B1_00_LPUART4_TXD				0x17C 0x36C 0x544 0x2 0x2
+#define MXRT1050_IOMUXC_GPIO_B1_00_SAI1_RX_DATA00			0x17C 0x36C 0x594 0x3 0x2
+#define MXRT1050_IOMUXC_GPIO_B1_00_FLEXIO2_D16				0x17C 0x36C 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_00_GPIO2_IO16				0x17C 0x36C 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_00_FLEXPWM1_PWM3_A			0x17C 0x36C 0x454 0x6 0x4
+
+#define MXRT1050_IOMUXC_GPIO_B1_01_LCD_DATA13				0x180 0x370 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_01_XBAR_INOUT15				0x180 0x370 0x648 0x1 0x1
+#define MXRT1050_IOMUXC_GPIO_B1_01_LPUART4_RXD				0x180 0x370 0x540 0x2 0x2
+#define MXRT1050_IOMUXC_GPIO_B1_01_SAI1_TX_DATA00			0x180 0x370 0x000 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_01_FLEXIO2_D17				0x180 0x370 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_01_GPIO2_IO17				0x180 0x370 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_01_FLEXPWM1_PWM3_B			0x180 0x370 0x464 0x6 0x4
+
+#define MXRT1050_IOMUXC_GPIO_B1_02_LCD_DATA14				0x184 0x374 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_02_XBAR_INOUT16				0x184 0x374 0x64C 0x1 0x1
+#define MXRT1050_IOMUXC_GPIO_B1_02_LPSPI4_PCS2				0x184 0x374 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_02_SAI1_TX_BCLK				0x184 0x374 0x5A8 0x3 0x2
+#define MXRT1050_IOMUXC_GPIO_B1_02_FLEXIO2_D18				0x184 0x374 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_02_GPIO2_IO18				0x184 0x374 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_02_FLEXPWM2_PWM3_A			0x184 0x374 0x000 0x6 0x0
+
+#define MXRT1050_IOMUXC_GPIO_B1_03_LCD_DATA15				0x188 0x378 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_03_XBAR_INOUT17				0x188 0x378 0x62C 0x1 0x3
+#define MXRT1050_IOMUXC_GPIO_B1_03_LPSPI4_PCS1				0x188 0x378 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_03_SAI1_TX_SYNC				0x188 0x378 0x5AC 0x3 0x2
+#define MXRT1050_IOMUXC_GPIO_B1_03_FLEXIO2_D19				0x188 0x378 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_03_GPIO2_IO19				0x188 0x378 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_03_FLEXPWM2_PWM3_B			0x188 0x378 0x484 0x6 0x3
+
+#define MXRT1050_IOMUXC_GPIO_B1_04_LCD_DATA16				0x18C 0x37C 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_04_LPSPI4_PCS0				0x18C 0x37C 0x51C 0x1 0x1
+#define MXRT1050_IOMUXC_GPIO_B1_04_CSI_DATA15				0x18C 0x37C 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_04_ENET_RX_DATA00			0x18C 0x37C 0x434 0x3 0x1
+#define MXRT1050_IOMUXC_GPIO_B1_04_FLEXIO2_D20				0x18C 0x37C 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_04_GPIO2_IO20				0x18C 0x37C 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_B1_05_LCD_DATA17				0x190 0x380 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_05_LPSPI4_SDI				0x190 0x380 0x524 0x1 0x1
+#define MXRT1050_IOMUXC_GPIO_B1_05_CSI_DATA14				0x190 0x380 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_05_ENET_RX_DATA01			0x190 0x380 0x438 0x3 0x1
+#define MXRT1050_IOMUXC_GPIO_B1_05_FLEXIO2_D21				0x190 0x380 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_05_GPIO2_IO21				0x190 0x380 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_B1_06_LCD_DATA18				0x194 0x384 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_06_LPSPI4_SDO				0x194 0x384 0x528 0x1 0x1
+#define MXRT1050_IOMUXC_GPIO_B1_06_CSI_DATA13				0x194 0x384 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_06_ENET_RX_EN				0x194 0x384 0x43C 0x3 0x1
+#define MXRT1050_IOMUXC_GPIO_B1_06_FLEXIO2_D22				0x194 0x384 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_06_GPIO2_IO22				0x194 0x384 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_B1_07_LCD_DATA19				0x198 0x388 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_07_LPSPI4_SCK				0x198 0x388 0x520 0x1 0x1
+#define MXRT1050_IOMUXC_GPIO_B1_07_CSI_DATA12				0x198 0x388 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_07_ENET_TX_DATA00			0x198 0x388 0x000 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_07_FLEXIO2_D23				0x198 0x388 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_07_GPIO2_IO23				0x198 0x388 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_B1_08_LCD_DATA20				0x19C 0x38C 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_08_TMR1_TIMER3				0x19C 0x38C 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_08_CSI_DATA11				0x19C 0x38C 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_08_ENET_TX_DATA01			0x19C 0x38C 0x000 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_08_FLEXIO2_D24				0x19C 0x38C 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_08_GPIO2_IO24				0x19C 0x38C 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_08_FLEXCAN2_TX				0x19C 0x38C 0x000 0x6 0x0
+
+#define MXRT1050_IOMUXC_GPIO_B1_09_LCD_DATA21				0x1A0 0x390 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_09_TMR2_TIMER3				0x1A0 0x390 0x578 0x1 0x1
+#define MXRT1050_IOMUXC_GPIO_B1_09_CSI_DATA10				0x1A0 0x390 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_09_ENET_TX_EN				0x1A0 0x390 0x000 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_09_FLEXIO2_D25				0x1A0 0x390 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_09_GPIO2_IO25				0x1A0 0x390 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_09_FLEXCAN2_RX				0x1A0 0x390 0x450 0x6 0x3
+
+#define MXRT1050_IOMUXC_GPIO_B1_10_LCD_DATA22				0x1A4 0x394 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_10_TMR3_TIMER3				0x1A4 0x394 0x588 0x1 0x2
+#define MXRT1050_IOMUXC_GPIO_B1_10_CSI_DATA00				0x1A4 0x394 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_10_ENET_TX_CLK				0x1A4 0x394 0x448 0x3 0x1
+#define MXRT1050_IOMUXC_GPIO_B1_10_FLEXIO2_D26				0x1A4 0x394 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_10_GPIO2_IO26				0x1A4 0x394 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_10_ENET_REF_CLK				0x1A4 0x394 0x42C 0x6 0x1
+
+#define MXRT1050_IOMUXC_GPIO_B1_11_LCD_DATA23				0x1A8 0x398 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_11_TMR4_TIMER3				0x1A8 0x398 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_11_CSI_DATA01				0x1A8 0x398 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_11_ENET_RX_ER				0x1A8 0x398 0x440 0x3 0x1
+#define MXRT1050_IOMUXC_GPIO_B1_11_FLEXIO2_D27				0x1A8 0x398 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_11_GPIO2_IO27				0x1A8 0x398 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_11_LPSPI4_PCS3				0x1A8 0x398 0x000 0x6 0x0
+
+#define MXRT1050_IOMUXC_GPIO_B1_12_LPUART5_TXD				0x1AC 0x39C 0x54C 0x1 0x1
+#define MXRT1050_IOMUXC_GPIO_B1_12_CSI_PIXCLK				0x1AC 0x39C 0x424 0x2 0x1
+#define MXRT1050_IOMUXC_GPIO_B1_12_ENET_1588_EVENT0_IN			0x1AC 0x39C 0x444 0x3 0x2
+#define MXRT1050_IOMUXC_GPIO_B1_12_FLEXIO2_D28				0x1AC 0x39C 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_12_GPIO2_IO28				0x1AC 0x39C 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_12_USDHC1_CD_B				0x1AC 0x39C 0x5D4 0x6 0x2
+
+#define MXRT1050_IOMUXC_GPIO_B1_13_WDOG1_B				0x1B0 0x3A0 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_13_LPUART5_RXD				0x1B0 0x3A0 0x548 0x1 0x1
+#define MXRT1050_IOMUXC_GPIO_B1_13_CSI_VSYNC				0x1B0 0x3A0 0x428 0x2 0x2
+#define MXRT1050_IOMUXC_GPIO_B1_13_ENET_1588_EVENT0_OUT			0x1B0 0x3A0 0x000 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_13_FLEXIO2_D29				0x1B0 0x3A0 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_13_GPIO2_IO29				0x1B0 0x3A0 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_13_USDHC1_WP				0x1B0 0x3A0 0x5D8 0x6 0x3
+
+#define MXRT1050_IOMUXC_GPIO_B1_14_ENET_MDC				0x1B4 0x3A4 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_14_FLEXPWM4_PWM2_A			0x1B4 0x3A4 0x49C 0x1 0x1
+#define MXRT1050_IOMUXC_GPIO_B1_14_CSI_HSYNC				0x1B4 0x3A4 0x420 0x2 0x2
+#define MXRT1050_IOMUXC_GPIO_B1_14_XBAR_INOUT02				0x1B4 0x3A4 0x60C 0x3 0x1
+#define MXRT1050_IOMUXC_GPIO_B1_14_FLEXIO2_D30				0x1B4 0x3A4 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_14_GPIO2_IO30				0x1B4 0x3A4 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_14_USDHC1_VSELECT			0x1B4 0x3A4 0x000 0x6 0x0
+
+#define MXRT1050_IOMUXC_GPIO_B1_15_ENET_MDIO				0x1B8 0x3A8 0x430 0x0 0x2
+#define MXRT1050_IOMUXC_GPIO_B1_15_FLEXPWM4_PWM3_A			0x1B8 0x3A8 0x4A0 0x1 0x1
+#define MXRT1050_IOMUXC_GPIO_B1_15_CSI_MCLK				0x1B8 0x3A8 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_15_XBAR_INOUT03				0x1B8 0x3A8 0x610 0x3 0x1
+#define MXRT1050_IOMUXC_GPIO_B1_15_FLEXIO2_D31				0x1B8 0x3A8 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_15_GPIO2_IO31				0x1B8 0x3A8 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_B1_15_USDHC1_RESET_B			0x1B8 0x3A8 0x000 0x6 0x0
+
+#define MXRT1050_IOMUXC_GPIO_SD_B0_00_USDHC1_CMD			0x1BC 0x3AC 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B0_00_FLEXPWM1_PWM0_A			0x1BC 0x3AC 0x458 0x1 0x1
+#define MXRT1050_IOMUXC_GPIO_SD_B0_00_LPI2C3_SCL			0x1BC 0x3AC 0x4DC 0x2 0x1
+#define MXRT1050_IOMUXC_GPIO_SD_B0_00_XBAR_INOUT04			0x1BC 0x3AC 0x614 0x3 0x1
+#define MXRT1050_IOMUXC_GPIO_SD_B0_00_LPSPI1_SCK			0x1BC 0x3AC 0x4F0 0x4 0x1
+#define MXRT1050_IOMUXC_GPIO_SD_B0_00_GPIO3_IO12			0x1BC 0x3AC 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B0_00_FLEXSPI_A_SS1_B			0x1BC 0x3AC 0x000 0x6 0x0
+
+#define MXRT1050_IOMUXC_GPIO_SD_B0_01_USDHC1_CLK			0x1C0 0x3B0 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B0_01_FLEXPWM1_PWM0_B			0x1C0 0x3B0 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B0_01_LPI2C3_SDA			0x1C0 0x3B0 0x4E0 0x2 0x1
+#define MXRT1050_IOMUXC_GPIO_SD_B0_01_XBAR_INOUT05			0x1C0 0x3B0 0x618 0x3 0x1
+#define MXRT1050_IOMUXC_GPIO_SD_B0_01_LPSPI1_PCS0			0x1C0 0x3B0 0x4EC 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B0_01_GPIO3_IO13			0x1C0 0x3B0 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B0_01_FLEXSPI_B_SS1_B			0x1C0 0x3B0 0x000 0x6 0x0
+
+#define MXRT1050_IOMUXC_GPIO_SD_B0_02_USDHC1_DATA0			0x1C4 0x3B4 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B0_02_FLEXPWM1_PWM1_A			0x1C4 0x3B4 0x45C 0x1 0x1
+#define MXRT1050_IOMUXC_GPIO_SD_B0_02_LPUART8_CTS_B			0x1C4 0x3B4 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B0_02_XBAR_INOUT06			0x1C4 0x3B4 0x61C 0x3 0x1
+#define MXRT1050_IOMUXC_GPIO_SD_B0_02_LPSPI1_SDO			0x1C4 0x3B4 0x4F8 0x4 0x1
+#define MXRT1050_IOMUXC_GPIO_SD_B0_02_GPIO3_IO14			0x1C4 0x3B4 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_SD_B0_03_USDHC1_DATA1			0x1C8 0x3B8 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B0_03_FLEXPWM1_PWM1_B			0x1C8 0x3B8 0x46C 0x1 0x1
+#define MXRT1050_IOMUXC_GPIO_SD_B0_03_LPUART8_RTS_B			0x1C8 0x3B8 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B0_03_XBAR_INOUT07			0x1C8 0x3B8 0x620 0x3 0x1
+#define MXRT1050_IOMUXC_GPIO_SD_B0_03_LPSPI1_SDI			0x1C8 0x3B8 0x4F4 0x4 0x1
+#define MXRT1050_IOMUXC_GPIO_SD_B0_03_GPIO3_IO15			0x1C8 0x3B8 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_SD_B0_04_USDHC1_DATA2			0x1CC 0x3BC 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B0_04_FLEXPWM1_PWM2_A			0x1CC 0x3BC 0x460 0x1 0x1
+#define MXRT1050_IOMUXC_GPIO_SD_B0_04_LPUART8_TXD			0x1CC 0x3BC 0x564 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B0_04_XBAR_INOUT08			0x1CC 0x3BC 0x624 0x3 0x1
+#define MXRT1050_IOMUXC_GPIO_SD_B0_04_FLEXSPI_B_SS0_B			0x1CC 0x3BC 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B0_04_GPIO3_IO16			0x1CC 0x3BC 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B0_04_CCM_CLKO1				0x1CC 0x3BC 0x000 0x6 0x0
+
+#define MXRT1050_IOMUXC_GPIO_SD_B0_05_USDHC1_DATA3			0x1D0 0x3C0 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B0_05_FLEXPWM1_PWM2_B			0x1D0 0x3C0 0x470 0x1 0x1
+#define MXRT1050_IOMUXC_GPIO_SD_B0_05_LPUART8_RXD			0x1D0 0x3C0 0x560 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B0_05_XBAR_INOUT09			0x1D0 0x3C0 0x628 0x3 0x1
+#define MXRT1050_IOMUXC_GPIO_SD_B0_05_FLEXSPI_B_DQS			0x1D0 0x3C0 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B0_05_GPIO3_IO17			0x1D0 0x3C0 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B0_05_CCM_CLKO2				0x1D0 0x3C0 0x000 0x6 0x0
+
+#define MXRT1050_IOMUXC_GPIO_SD_B1_00_USDHC2_DATA3			0x1D4 0x3C4 0x5F4 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_00_FLEXSPI_B_DATA3			0x1D4 0x3C4 0x4C4 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_00_FLEXPWM1_PWM3_A			0x1D4 0x3C4 0x454 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_00_SAI1_TX_DATA03			0x1D4 0x3C4 0x598 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_00_LPUART4_TXD			0x1D4 0x3C4 0x544 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_00_GPIO3_IO00			0x1D4 0x3C4 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_SD_B1_01_USDHC2_DATA2			0x1D8 0x3C8 0x5F0 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_01_FLEXSPI_B_DATA2			0x1D8 0x3C8 0x4C0 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_01_FLEXPWM1_PWM3_B			0x1D8 0x3C8 0x464 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_01_SAI1_TX_DATA02			0x1D8 0x3C8 0x59C 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_01_LPUART4_RXD			0x1D8 0x3C8 0x540 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_01_GPIO3_IO01			0x1D8 0x3C8 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_SD_B1_02_USDHC2_DATA1			0x1DC 0x3CC 0x5EC 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_02_FLEXSPI_B_DATA1			0x1DC 0x3CC 0x4BC 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_02_FLEXPWM2_PWM3_A			0x1DC 0x3CC 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_02_SAI1_TX_DATA01			0x1DC 0x3CC 0x5A0 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_02_FLEXCAN1_TX			0x1DC 0x3CC 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_02_GPIO3_IO02			0x1DC 0x3CC 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_02_CCM_WAIT				0x1DC 0x3CC 0x000 0x6 0x0
+
+#define MXRT1050_IOMUXC_GPIO_SD_B1_03_USDHC2_DATA0			0x1E0 0x3D0 0x5E8 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_03_FLEXSPI_B_DATA0			0x1E0 0x3D0 0x4B8 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_03_FLEXPWM2_PWM3_B			0x1E0 0x3D0 0x484 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_03_SAI1_MCLK				0x1E0 0x3D0 0x58C 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_03_FLEXCAN1_RX			0x1E0 0x3D0 0x44C 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_03_GPIO3_IO03			0x1E0 0x3D0 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_03_CCM_PMIC_READY			0x1E0 0x3D0 0x3FC 0x6 0x0
+
+#define MXRT1050_IOMUXC_GPIO_SD_B1_04_USDHC2_CLK			0x1E4 0x3D4 0x5DC 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_04_FLEXSPI_B_SCLK			0x1E4 0x3D4 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_04_LPI2C1_SCL			0x1E4 0x3D4 0x4CC 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_04_SAI1_RX_SYNC			0x1E4 0x3D4 0x5A4 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_04_FLEXCAN1_A_SS1_B			0x1E4 0x3D4 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_04_GPIO3_IO04			0x1E4 0x3D4 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_04_CCM_STOP				0x1E4 0x3D4 0x000 0x6 0x0
+
+#define MXRT1050_IOMUXC_GPIO_SD_B1_05_USDHC2_CMD			0x1E8 0x3D8 0x5E4 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_05_FLEXSPI_A_DQS			0x1E8 0x3D8 0x4A4 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_05_LPI2C1_SDA			0x1E8 0x3D8 0x4D0 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_05_SAI1_RX_BCLK			0x1E8 0x3D8 0x590 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_05_FLEXCAN1_B_SS0_B			0x1E8 0x3D8 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_05_GPIO3_IO05			0x1E8 0x3D8 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_SD_B1_06_USDHC2_RESET_B			0x1EC 0x3DC 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_06_FLEXSPI_A_SS0_B			0x1EC 0x3DC 0x000 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_06_LPUART7_CTS_B			0x1EC 0x3DC 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_06_SAI1_RX_DATA00			0x1EC 0x3DC 0x594 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_06_LPSPI2_PCS0			0x1EC 0x3DC 0x4FC 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_06_GPIO3_IO06			0x1EC 0x3DC 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_SD_B1_07_SEMC_CSX1				0x1F0 0x3E0 0x000 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_07_FLEXSPI_A_SCLK			0x1F0 0x3E0 0x4C8 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_07_LPUART7_RTS_B			0x1F0 0x3E0 0x000 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_07_SAI1_TX_DATA00			0x1F0 0x3E0 0x000 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_07_LPSPI2_SCK			0x1F0 0x3E0 0x500 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_07_GPIO3_IO07			0x1F0 0x3E0 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_07_CCM_REF_EN_B			0x1F0 0x3E0 0x000 0x6 0x0
+
+#define MXRT1050_IOMUXC_GPIO_SD_B1_08_USDHC2_DATA4			0x1F4 0x3E4 0x5F8 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_08_FLEXSPI_A_DATA0			0x1F4 0x3E4 0x4A8 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_08_LPUART7_TXD			0x1F4 0x3E4 0x55C 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_08_SAI1_TX_BLCK			0x1F4 0x3E4 0x5A8 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_08_LPSPI2_SDO			0x1F4 0x3E4 0x508 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_08_GPIO3_IO08			0x1F4 0x3E4 0x000 0x5 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_08_SEMC_CSX2				0x1F4 0x3E4 0x000 0x6 0x0
+
+#define MXRT1050_IOMUXC_GPIO_SD_B1_09_USDHC2_DATA5			0x1F8 0x3E8 0x5FC 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_09_FLEXSPI_A_DATA1			0x1F8 0x3E8 0x4AC 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_09_LPUART7_RXD			0x1F8 0x3E8 0x558 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_09_SAI1_TX_SYNC			0x1F8 0x3E8 0x5AC 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_09_LPSPI2_SDI			0x1F8 0x3E8 0x504 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_09_GPIO3_IO09			0x1F8 0x3E8 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_SD_B1_10_USDHC2_DATA6			0x1FC 0x3EC 0x600 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_10_FLEXSPI_A_DATA2			0x1FC 0x3EC 0x4B0 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_10_LPUART2_RXD			0x1FC 0x3EC 0x52C 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_10_LPI2C2_SDA			0x1FC 0x3EC 0x4D8 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_10_LPSPI2_PCS2			0x1FC 0x3EC 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_10_GPIO3_IO10			0x1FC 0x3EC 0x000 0x5 0x0
+
+#define MXRT1050_IOMUXC_GPIO_SD_B1_11_USDHC2_DATA7			0x200 0x3F0 0x604 0x0 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_11_FLEXSPI_A_DATA3			0x200 0x3F0 0x4B4 0x1 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_11_LPUART2_TXD			0x200 0x3F0 0x530 0x2 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_11_LPI2C2_SCL			0x200 0x3F0 0x4D4 0x3 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_11_LPSPI2_PCS3			0x200 0x3F0 0x000 0x4 0x0
+#define MXRT1050_IOMUXC_GPIO_SD_B1_11_GPIO3_IO11			0x200 0x3F0 0x000 0x5 0x0
+
+#endif /* _DT_BINDINGS_PINCTRL_IMXRT1050_PINFUNC_H */
diff --git a/arch/arm/boot/dts/imxrt1050.dtsi b/arch/arm/boot/dts/imxrt1050.dtsi
new file mode 100644
index 000000000000..03e6a858a7be
--- /dev/null
+++ b/arch/arm/boot/dts/imxrt1050.dtsi
@@ -0,0 +1,160 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2019
+ * Author(s): Giulio Benetti <giulio.benetti@benettiengineering.com>
+ */
+
+#include "armv7-m.dtsi"
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/imxrt1050-clock.h>
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	clocks {
+		osc: osc {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <24000000>;
+		};
+
+		osc3M: osc3M {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <3000000>;
+		};
+	};
+
+	soc {
+		lpuart1: serial@40184000 {
+			compatible = "fsl,imxrt1050-lpuart", "fsl,imx7ulp-lpuart";
+			reg = <0x40184000 0x4000>;
+			interrupts = <20>;
+			clocks = <&clks IMXRT1050_CLK_LPUART1>;
+			clock-names = "ipg";
+			status = "disabled";
+		};
+
+		iomuxc: pinctrl@401f8000 {
+			compatible = "fsl,imxrt1050-iomuxc";
+			reg = <0x401f8000 0x4000>;
+			fsl,mux_mask = <0x7>;
+		};
+
+		anatop: anatop@400d8000 {
+			compatible = "fsl,imxrt-anatop";
+			reg = <0x400d8000 0x4000>;
+		};
+
+		clks: clock-controller@400fc000 {
+			compatible = "fsl,imxrt1050-ccm";
+			reg = <0x400fc000 0x4000>;
+			interrupts = <95>, <96>;
+			clocks = <&osc>;
+			clock-names = "osc";
+			#clock-cells = <1>;
+			assigned-clocks = <&clks IMXRT1050_CLK_PLL1_BYPASS>,
+				<&clks IMXRT1050_CLK_PLL1_BYPASS>,
+				<&clks IMXRT1050_CLK_PLL2_BYPASS>,
+				<&clks IMXRT1050_CLK_PLL3_BYPASS>,
+				<&clks IMXRT1050_CLK_PLL3_PFD1_664_62M>,
+				<&clks IMXRT1050_CLK_PLL2_PFD2_396M>;
+			assigned-clock-parents = <&clks IMXRT1050_CLK_PLL1_REF_SEL>,
+				<&clks IMXRT1050_CLK_PLL1_ARM>,
+				<&clks IMXRT1050_CLK_PLL2_SYS>,
+				<&clks IMXRT1050_CLK_PLL3_USB_OTG>,
+				<&clks IMXRT1050_CLK_PLL3_USB_OTG>,
+				<&clks IMXRT1050_CLK_PLL2_SYS>;
+		};
+
+		edma1: dma-controller@400e8000 {
+			#dma-cells = <2>;
+			compatible = "fsl,imx7ulp-edma";
+			reg = <0x400e8000 0x4000>,
+				<0x400ec000 0x4000>;
+			dma-channels = <32>;
+			interrupts = <0>, <1>, <2>, <3>, <4>, <5>, <6>, <7>, <8>,
+				<9>, <10>, <11>, <12>, <13>, <14>, <15>, <16>;
+			clock-names = "dma", "dmamux0";
+			clocks = <&clks IMXRT1050_CLK_DMA>,
+				 <&clks IMXRT1050_CLK_DMA_MUX>;
+		};
+
+		usdhc1: mmc@402c0000 {
+			compatible = "fsl,imxrt1050-usdhc", "fsl,imx6sl-usdhc";
+			reg = <0x402c0000 0x4000>;
+			interrupts = <110>;
+			clocks = <&clks IMXRT1050_CLK_IPG_PDOF>,
+				<&clks IMXRT1050_CLK_OSC>,
+				<&clks IMXRT1050_CLK_USDHC1>;
+			clock-names = "ipg", "ahb", "per";
+			bus-width = <4>;
+			fsl,wp-controller;
+			no-1-8-v;
+			max-frequency = <4000000>;
+			fsl,tuning-start-tap = <20>;
+			fsl,tuning-step = <2>;
+			status = "disabled";
+		};
+
+		gpio1: gpio@401b8000 {
+			compatible = "fsl,imxrt1050-gpio", "fsl,imx35-gpio";
+			reg = <0x401b8000 0x4000>;
+			interrupts = <80>, <81>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpio2: gpio@401bc000 {
+			compatible = "fsl,imxrt1050-gpio", "fsl,imx35-gpio";
+			reg = <0x401bc000 0x4000>;
+			interrupts = <82>, <83>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpio3: gpio@401c0000 {
+			compatible = "fsl,imxrt1050-gpio", "fsl,imx35-gpio";
+			reg = <0x401c0000 0x4000>;
+			interrupts = <84>, <85>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpio4: gpio@401c4000 {
+			compatible = "fsl,imxrt1050-gpio", "fsl,imx35-gpio";
+			reg = <0x401c4000 0x4000>;
+			interrupts = <86>, <87>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpio5: gpio@400c0000 {
+			compatible = "fsl,imxrt1050-gpio", "fsl,imx35-gpio";
+			reg = <0x400c0000 0x4000>;
+			interrupts = <88>, <89>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpt: timer@401ec000 {
+			compatible = "fsl,imxrt1050-gpt", "fsl,imx6dl-gpt", "fsl,imx6sl-gpt";
+			reg = <0x401ec000 0x4000>;
+			interrupts = <100>;
+			clocks = <&osc3M>;
+			clock-names = "per";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/imxrt1170-pinfunc.h b/arch/arm/boot/dts/imxrt1170-pinfunc.h
new file mode 100644
index 000000000000..3b9fff2f08e1
--- /dev/null
+++ b/arch/arm/boot/dts/imxrt1170-pinfunc.h
@@ -0,0 +1,1561 @@
+/* SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) */
+/*
+ * Copyright (C) 2021
+ * Author(s): Jesse Taube <Mr.Bossman075@gmail.com>
+ */
+
+#ifndef _DT_BINDINGS_PINCTRL_IMXRT1170_PINFUNC_H
+#define _DT_BINDINGS_PINCTRL_IMXRT1170_PINFUNC_H
+
+#define IMX_PAD_SION		0x40000000
+
+/*
+ * The pin function ID is a tuple of
+ * <mux_reg conf_reg input_reg mux_mode input_val>
+ */
+
+#define IOMUXC_GPIO_LPSR_00_FLEXCAN3_TX				0x000 0x040 0x0 0x0 0x0
+#define IOMUXC_GPIO_LPSR_00_MIC_CLK				0x000 0x040 0x0 0x1 0x0
+#define IOMUXC_GPIO_LPSR_00_MQS_RIGHT				0x000 0x040 0x0 0x2 0x0
+#define IOMUXC_GPIO_LPSR_00_ARM_CM4_EVENTO			0x000 0x040 0x0 0x3 0x0
+#define IOMUXC_GPIO_LPSR_00_GPIO_MUX6_IO00			0x000 0x040 0x0 0x5 0x0
+#define IOMUXC_GPIO_LPSR_00_LPUART12_TXD			0x000 0x040 0x0B0 0x6 0x0
+#define IOMUXC_GPIO_LPSR_00_SAI4_MCLK				0x000 0x040 0x0C8 0x7 0x0
+#define IOMUXC_GPIO_LPSR_00_GPIO12_IO00				0x000 0x040 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_LPSR_01_FLEXCAN3_RX				0x004 0x044 0x080 0x0 0x0
+#define IOMUXC_GPIO_LPSR_01_MIC_BITSTREAM0			0x004 0x044 0x0B4 0x1 0x0
+#define IOMUXC_GPIO_LPSR_01_MQS_LEFT				0x004 0x044 0x0 0x2 0x0
+#define IOMUXC_GPIO_LPSR_01_ARM_CM4_EVENTI			0x004 0x044 0x0 0x3 0x0
+#define IOMUXC_GPIO_LPSR_01_GPIO_MUX6_IO01			0x004 0x044 0x0 0x5 0x0
+#define IOMUXC_GPIO_LPSR_01_LPUART12_RXD			0x004 0x044 0x0AC 0x6 0x0
+#define IOMUXC_GPIO_LPSR_01_GPIO12_IO01				0x004 0x044 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_LPSR_02_GPIO12_IO02				0x008 0x048 0x0 0xA 0x0
+#define IOMUXC_GPIO_LPSR_02_SRC_BOOT_MODE00			0x008 0x048 0x0 0x0 0x0
+#define IOMUXC_GPIO_LPSR_02_LPSPI5_SCK				0x008 0x048 0x098 0x1 0x0
+#define IOMUXC_GPIO_LPSR_02_SAI4_TX_DATA			0x008 0x048 0x0 0x2 0x0
+#define IOMUXC_GPIO_LPSR_02_MQS_RIGHT				0x008 0x048 0x0 0x3 0x0
+#define IOMUXC_GPIO_LPSR_02_GPIO_MUX6_IO02			0x008 0x048 0x0 0x5 0x0
+
+#define IOMUXC_GPIO_LPSR_03_SRC_BOOT_MODE01			0x00C 0x04C 0x0 0x0 0x0
+#define IOMUXC_GPIO_LPSR_03_LPSPI5_PCS0				0x00C 0x04C 0x094 0x1 0x0
+#define IOMUXC_GPIO_LPSR_03_SAI4_TX_SYNC			0x00C 0x04C 0x0DC 0x2 0x0
+#define IOMUXC_GPIO_LPSR_03_MQS_LEFT				0x00C 0x04C 0x0 0x3 0x0
+#define IOMUXC_GPIO_LPSR_03_GPIO_MUX6_IO03			0x00C 0x04C 0x0 0x5 0x0
+#define IOMUXC_GPIO_LPSR_03_GPIO12_IO03				0x00C 0x04C 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_LPSR_04_LPI2C5_SDA				0x010 0x050 0x088 0x0 0x0
+#define IOMUXC_GPIO_LPSR_04_LPSPI5_SOUT				0x010 0x050 0x0A0 0x1 0x0
+#define IOMUXC_GPIO_LPSR_04_SAI4_TX_BCLK			0x010 0x050 0x0D8 0x2 0x0
+#define IOMUXC_GPIO_LPSR_04_LPUART12_RTS_B			0x010 0x050 0x0 0x3 0x0
+#define IOMUXC_GPIO_LPSR_04_GPIO_MUX6_IO04			0x010 0x050 0x0 0x5 0x0
+#define IOMUXC_GPIO_LPSR_04_LPUART11_TXD			0x010 0x050 0x0A8 0x6 0x0
+#define IOMUXC_GPIO_LPSR_04_GPIO12_IO04				0x010 0x050 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_LPSR_05_GPIO12_IO05				0x014 0x054 0x0 0xA 0x0
+#define IOMUXC_GPIO_LPSR_05_LPI2C5_SCL				0x014 0x054 0x084 0x0 0x0
+#define IOMUXC_GPIO_LPSR_05_LPSPI5_SIN				0x014 0x054 0x09C 0x1 0x0
+#define IOMUXC_GPIO_LPSR_05_SAI4_MCLK				0x014 0x054 0x0C8 0x2 0x1
+#define IOMUXC_GPIO_LPSR_05_LPUART12_CTS_B			0x014 0x054 0x0 0x3 0x0
+#define IOMUXC_GPIO_LPSR_05_GPIO_MUX6_IO05			0x014 0x054 0x0 0x5 0x0
+#define IOMUXC_GPIO_LPSR_05_LPUART11_RXD			0x014 0x054 0x0A4 0x6 0x0
+#define IOMUXC_GPIO_LPSR_05_NMI_GLUE_NMI			0x014 0x054 0x0C4 0x7 0x0
+
+#define IOMUXC_GPIO_LPSR_06_LPI2C6_SDA				0x018 0x058 0x090 0x0 0x0
+#define IOMUXC_GPIO_LPSR_06_SAI4_RX_DATA			0x018 0x058 0x0D0 0x2 0x0
+#define IOMUXC_GPIO_LPSR_06_LPUART12_TXD			0x018 0x058 0x0B0 0x3 0x1
+#define IOMUXC_GPIO_LPSR_06_LPSPI6_PCS3				0x018 0x058 0x0 0x4 0x0
+#define IOMUXC_GPIO_LPSR_06_GPIO_MUX6_IO06			0x018 0x058 0x0 0x5 0x0
+#define IOMUXC_GPIO_LPSR_06_FLEXCAN3_TX				0x018 0x058 0x0 0x6 0x0
+#define IOMUXC_GPIO_LPSR_06_PIT2_TRIGGER3			0x018 0x058 0x0 0x7 0x0
+#define IOMUXC_GPIO_LPSR_06_LPSPI5_PCS1				0x018 0x058 0x0 0x8 0x0
+#define IOMUXC_GPIO_LPSR_06_GPIO12_IO06				0x018 0x058 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_LPSR_07_LPI2C6_SCL				0x01C 0x05C 0x08C 0x0 0x0
+#define IOMUXC_GPIO_LPSR_07_SAI4_RX_BCLK			0x01C 0x05C 0x0CC 0x2 0x0
+#define IOMUXC_GPIO_LPSR_07_LPUART12_RXD			0x01C 0x05C 0x0AC 0x3 0x1
+#define IOMUXC_GPIO_LPSR_07_LPSPI6_PCS2				0x01C 0x05C 0x0 0x4 0x0
+#define IOMUXC_GPIO_LPSR_07_GPIO_MUX6_IO07			0x01C 0x05C 0x0 0x5 0x0
+#define IOMUXC_GPIO_LPSR_07_FLEXCAN3_RX				0x01C 0x05C 0x080 0x6 0x1
+#define IOMUXC_GPIO_LPSR_07_PIT2_TRIGGER2			0x01C 0x05C 0x0 0x7 0x0
+#define IOMUXC_GPIO_LPSR_07_LPSPI5_PCS2				0x01C 0x05C 0x0 0x8 0x0
+#define IOMUXC_GPIO_LPSR_07_GPIO12_IO07				0x01C 0x05C 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_LPSR_08_GPIO12_IO08				0x020 0x060 0x0 0xA 0x0
+#define IOMUXC_GPIO_LPSR_08_LPUART11_TXD			0x020 0x060 0x0A8 0x0 0x1
+#define IOMUXC_GPIO_LPSR_08_FLEXCAN3_TX				0x020 0x060 0x0 0x1 0x0
+#define IOMUXC_GPIO_LPSR_08_SAI4_RX_SYNC			0x020 0x060 0x0D4 0x2 0x0
+#define IOMUXC_GPIO_LPSR_08_MIC_CLK				0x020 0x060 0x0 0x3 0x0
+#define IOMUXC_GPIO_LPSR_08_LPSPI6_PCS1				0x020 0x060 0x0 0x4 0x0
+#define IOMUXC_GPIO_LPSR_08_GPIO_MUX6_IO08			0x020 0x060 0x0 0x5 0x0
+#define IOMUXC_GPIO_LPSR_08_LPI2C5_SDA				0x020 0x060 0x088 0x6 0x1
+#define IOMUXC_GPIO_LPSR_08_PIT2_TRIGGER1			0x020 0x060 0x0 0x7 0x0
+#define IOMUXC_GPIO_LPSR_08_LPSPI5_PCS3				0x020 0x060 0x0 0x8 0x0
+
+#define IOMUXC_GPIO_LPSR_09_GPIO12_IO09				0x024 0x064 0x0 0xA 0x0
+#define IOMUXC_GPIO_LPSR_09_LPUART11_RXD			0x024 0x064 0x0A4 0x0 0x1
+#define IOMUXC_GPIO_LPSR_09_FLEXCAN3_RX				0x024 0x064 0x080 0x1 0x2
+#define IOMUXC_GPIO_LPSR_09_PIT2_TRIGGER0			0x024 0x064 0x0 0x2 0x0
+#define IOMUXC_GPIO_LPSR_09_MIC_BITSTREAM0			0x024 0x064 0x0B4 0x3 0x1
+#define IOMUXC_GPIO_LPSR_09_LPSPI6_PCS0				0x024 0x064 0x0 0x4 0x0
+#define IOMUXC_GPIO_LPSR_09_GPIO_MUX6_IO09			0x024 0x064 0x0 0x5 0x0
+#define IOMUXC_GPIO_LPSR_09_LPI2C5_SCL				0x024 0x064 0x084 0x6 0x1
+#define IOMUXC_GPIO_LPSR_09_SAI4_TX_DATA			0x024 0x064 0x0 0x7 0x0
+
+#define IOMUXC_GPIO_LPSR_10_GPIO12_IO10				0x028 0x068 0x0 0xA 0x0
+#define IOMUXC_GPIO_LPSR_10_JTAG_MUX_TRSTB			0x028 0x068 0x0 0x0 0x0
+#define IOMUXC_GPIO_LPSR_10_LPUART11_CTS_B			0x028 0x068 0x0 0x1 0x0
+#define IOMUXC_GPIO_LPSR_10_LPI2C6_SDA				0x028 0x068 0x090 0x2 0x1
+#define IOMUXC_GPIO_LPSR_10_MIC_BITSTREAM1			0x028 0x068 0x0B8 0x3 0x0
+#define IOMUXC_GPIO_LPSR_10_LPSPI6_SCK				0x028 0x068 0x0 0x4 0x0
+#define IOMUXC_GPIO_LPSR_10_GPIO_MUX6_IO10			0x028 0x068 0x0 0x5 0x0
+#define IOMUXC_GPIO_LPSR_10_LPI2C5_SCLS				0x028 0x068 0x0 0x6 0x0
+#define IOMUXC_GPIO_LPSR_10_SAI4_TX_SYNC			0x028 0x068 0x0DC 0x7 0x1
+#define IOMUXC_GPIO_LPSR_10_LPUART12_TXD			0x028 0x068 0x0B0 0x8 0x2
+
+#define IOMUXC_GPIO_LPSR_11_JTAG_MUX_TDO			0x02C 0x06C 0x0 0x0 0x0
+#define IOMUXC_GPIO_LPSR_11_LPUART11_RTS_B			0x02C 0x06C 0x0 0x1 0x0
+#define IOMUXC_GPIO_LPSR_11_LPI2C6_SCL				0x02C 0x06C 0x08C 0x2 0x1
+#define IOMUXC_GPIO_LPSR_11_MIC_BITSTREAM2			0x02C 0x06C 0x0BC 0x3 0x0
+#define IOMUXC_GPIO_LPSR_11_LPSPI6_SOUT				0x02C 0x06C 0x0 0x4 0x0
+#define IOMUXC_GPIO_LPSR_11_GPIO_MUX6_IO11			0x02C 0x06C 0x0 0x5 0x0
+#define IOMUXC_GPIO_LPSR_11_LPI2C5_SDAS				0x02C 0x06C 0x0 0x6 0x0
+#define IOMUXC_GPIO_LPSR_11_ARM_TRACE_SWO			0x02C 0x06C 0x0 0x7 0x0
+#define IOMUXC_GPIO_LPSR_11_LPUART12_RXD			0x02C 0x06C 0x0AC 0x8 0x2
+#define IOMUXC_GPIO_LPSR_11_GPIO12_IO11				0x02C 0x06C 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_LPSR_12_GPIO12_IO12				0x030 0x070 0x0 0xA 0x0
+#define IOMUXC_GPIO_LPSR_12_JTAG_MUX_TDI			0x030 0x070 0x0 0x0 0x0
+#define IOMUXC_GPIO_LPSR_12_PIT2_TRIGGER0			0x030 0x070 0x0 0x1 0x0
+#define IOMUXC_GPIO_LPSR_12_MIC_BITSTREAM3			0x030 0x070 0x0C0 0x3 0x0
+#define IOMUXC_GPIO_LPSR_12_LPSPI6_SIN				0x030 0x070 0x0 0x4 0x0
+#define IOMUXC_GPIO_LPSR_12_GPIO_MUX6_IO12			0x030 0x070 0x0 0x5 0x0
+#define IOMUXC_GPIO_LPSR_12_LPI2C5_HREQ				0x030 0x070 0x0 0x6 0x0
+#define IOMUXC_GPIO_LPSR_12_SAI4_TX_BCLK			0x030 0x070 0x0D8 0x7 0x1
+#define IOMUXC_GPIO_LPSR_12_LPSPI5_SCK				0x030 0x070 0x098 0x8 0x1
+
+#define IOMUXC_GPIO_LPSR_13_GPIO12_IO13				0x034 0x074 0x0 0xA 0x0
+#define IOMUXC_GPIO_LPSR_13_JTAG_MUX_MOD			0x034 0x074 0x0 0x0 0x0
+#define IOMUXC_GPIO_LPSR_13_MIC_BITSTREAM1			0x034 0x074 0x0B8 0x1 0x1
+#define IOMUXC_GPIO_LPSR_13_PIT2_TRIGGER1			0x034 0x074 0x0 0x2 0x0
+#define IOMUXC_GPIO_LPSR_13_GPIO_MUX6_IO13			0x034 0x074 0x0 0x5 0x0
+#define IOMUXC_GPIO_LPSR_13_SAI4_RX_DATA			0x034 0x074 0x0D0 0x7 0x1
+#define IOMUXC_GPIO_LPSR_13_LPSPI5_PCS0				0x034 0x074 0x094 0x8 0x1
+
+#define IOMUXC_GPIO_LPSR_14_JTAG_MUX_TCK			0x038 0x078 0x0 0x0 0x0
+#define IOMUXC_GPIO_LPSR_14_MIC_BITSTREAM2			0x038 0x078 0x0BC 0x1 0x1
+#define IOMUXC_GPIO_LPSR_14_PIT2_TRIGGER2			0x038 0x078 0x0 0x2 0x0
+#define IOMUXC_GPIO_LPSR_14_GPIO_MUX6_IO14			0x038 0x078 0x0 0x5 0x0
+#define IOMUXC_GPIO_LPSR_14_SAI4_RX_BCLK			0x038 0x078 0x0CC 0x7 0x1
+#define IOMUXC_GPIO_LPSR_14_LPSPI5_SOUT				0x038 0x078 0x0A0 0x8 0x1
+#define IOMUXC_GPIO_LPSR_14_GPIO12_IO14				0x038 0x078 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_LPSR_15_GPIO12_IO15				0x03C 0x07C 0x0 0xA 0x0
+#define IOMUXC_GPIO_LPSR_15_JTAG_MUX_TMS			0x03C 0x07C 0x0 0x0 0x0
+#define IOMUXC_GPIO_LPSR_15_MIC_BITSTREAM3			0x03C 0x07C 0x0C0 0x1 0x1
+#define IOMUXC_GPIO_LPSR_15_PIT2_TRIGGER3			0x03C 0x07C 0x0 0x2 0x0
+#define IOMUXC_GPIO_LPSR_15_GPIO_MUX6_IO15			0x03C 0x07C 0x0 0x5 0x0
+#define IOMUXC_GPIO_LPSR_15_SAI4_RX_SYNC			0x03C 0x07C 0x0D4 0x7 0x1
+#define IOMUXC_GPIO_LPSR_15_LPSPI5_SIN				0x03C 0x07C 0x09C 0x8 0x1
+
+#define IOMUXC_WAKEUP_DIG_GPIO13_IO00				0x40C94000 0x40C94040 0x0 0x5 0x0
+#define IOMUXC_WAKEUP_DIG_NMI_GLUE_NMI				0x40C94000 0x40C94040 0x0C4 0x7 0x1
+
+#define IOMUXC_PMIC_ON_REQ_DIG_SNVS_LP_PMIC_ON_REQ		0x40C94004 0x40C94044 0x0 0x0 0x0
+#define IOMUXC_PMIC_ON_REQ_DIG_GPIO13_IO01			0x40C94004 0x40C94044 0x0 0x5 0x0
+
+#define IOMUXC_PMIC_STBY_REQ_DIG_CCM_PMIC_VSTBY_REQ		0x40C94008 0x40C94048 0x0 0x0 0x0
+#define IOMUXC_PMIC_STBY_REQ_DIG_GPIO13_IO02			0x40C94008 0x40C94048 0x0 0x5 0x0
+
+#define IOMUXC_GPIO_SNVS_00_DIG_SNVS_TAMPER0			0x40C9400C 0x40C9404C 0x0 0x0 0x0
+#define IOMUXC_GPIO_SNVS_00_DIG_GPIO13_IO03			0x40C9400C 0x40C9404C 0x0 0x5 0x0
+
+#define IOMUXC_GPIO_SNVS_01_DIG_SNVS_TAMPER1			0x40C94010 0x40C94050 0x0 0x0 0x0
+#define IOMUXC_GPIO_SNVS_01_DIG_GPIO13_IO04			0x40C94010 0x40C94050 0x0 0x5 0x0
+
+#define IOMUXC_GPIO_SNVS_02_DIG_SNVS_TAMPER2			0x40C94014 0x40C94054 0x0 0x0 0x0
+#define IOMUXC_GPIO_SNVS_02_DIG_GPIO13_IO05			0x40C94014 0x40C94054 0x0 0x5 0x0
+
+#define IOMUXC_GPIO_SNVS_03_DIG_SNVS_TAMPER3			0x40C94018 0x40C94058 0x0 0x0 0x0
+#define IOMUXC_GPIO_SNVS_03_DIG_GPIO13_IO06			0x40C94018 0x40C94058 0x0 0x5 0x0
+
+#define IOMUXC_GPIO_SNVS_04_DIG_SNVS_TAMPER4			0x40C9401C 0x40C9405C 0x0 0x0 0x0
+#define IOMUXC_GPIO_SNVS_04_DIG_GPIO13_IO07			0x40C9401C 0x40C9405C 0x0 0x5 0x0
+
+#define IOMUXC_GPIO_SNVS_05_DIG_SNVS_TAMPER5			0x40C94020 0x40C94060 0x0 0x0 0x0
+#define IOMUXC_GPIO_SNVS_05_DIG_GPIO13_IO08			0x40C94020 0x40C94060 0x0 0x5 0x0
+
+#define IOMUXC_GPIO_SNVS_06_DIG_SNVS_TAMPER6			0x40C94024 0x40C94064 0x0 0x0 0x0
+#define IOMUXC_GPIO_SNVS_06_DIG_GPIO13_IO09			0x40C94024 0x40C94064 0x0 0x5 0x0
+
+#define IOMUXC_GPIO_SNVS_07_DIG_SNVS_TAMPER7			0x40C94028 0x40C94068 0x0 0x0 0x0
+#define IOMUXC_GPIO_SNVS_07_DIG_GPIO13_IO10			0x40C94028 0x40C94068 0x0 0x5 0x0
+
+#define IOMUXC_GPIO_SNVS_08_DIG_SNVS_TAMPER8			0x40C9402C 0x40C9406C 0x0 0x0 0x0
+#define IOMUXC_GPIO_SNVS_08_DIG_GPIO13_IO11			0x40C9402C 0x40C9406C 0x0 0x5 0x0
+
+#define IOMUXC_GPIO_SNVS_09_DIG_SNVS_TAMPER9			0x40C94030 0x40C94070 0x0 0x0 0x0
+#define IOMUXC_GPIO_SNVS_09_DIG_GPIO13_IO12			0x40C94030 0x40C94070 0x0 0x5 0x0
+
+#define IOMUXC_TEST_MODE_DIG					0x0 0x40C94034 0x0 0x0 0x0
+
+#define IOMUXC_POR_B_DIG					0x0 0x40C94038 0x0 0x0 0x0
+
+#define IOMUXC_ONOFF_DIG					0x0 0x40C9403C 0x0 0x0 0x0
+
+#define IOMUXC_GPIO_EMC_B1_00_SEMC_DATA00			0x010 0x254 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_00_FLEXPWM4_PWM0_A			0x010 0x254 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_00_GPIO_MUX1_IO00			0x010 0x254 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_00_FLEXIO1_D00			0x010 0x254 0x0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B1_00_GPIO7_IO00			0x010 0x254 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B1_01_GPIO7_IO01			0x014 0x258 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B1_01_SEMC_DATA01			0x014 0x258 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_01_FLEXPWM4_PWM0_B			0x014 0x258 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_01_GPIO_MUX1_IO01			0x014 0x258 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_01_FLEXIO1_D01			0x014 0x258 0x0 0x8 0x0
+
+#define IOMUXC_GPIO_EMC_B1_02_SEMC_DATA02			0x018 0x25C 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_02_FLEXPWM4_PWM1_A			0x018 0x25C 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_02_GPIO_MUX1_IO02			0x018 0x25C 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_02_FLEXIO1_D02			0x018 0x25C 0x0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B1_02_GPIO7_IO02			0x018 0x25C 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B1_03_SEMC_DATA03			0x01C 0x260 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_03_FLEXPWM4_PWM1_B			0x01C 0x260 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_03_GPIO_MUX1_IO03			0x01C 0x260 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_03_FLEXIO1_D03			0x01C 0x260 0x0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B1_03_GPIO7_IO03			0x01C 0x260 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B1_04_GPIO7_IO04			0x020 0x264 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B1_04_SEMC_DATA04			0x020 0x264 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_04_FLEXPWM4_PWM2_A			0x020 0x264 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_04_GPIO_MUX1_IO04			0x020 0x264 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_04_FLEXIO1_D04			0x020 0x264 0x0 0x8 0x0
+
+#define IOMUXC_GPIO_EMC_B1_05_SEMC_DATA05			0x024 0x268 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_05_FLEXPWM4_PWM2_B			0x024 0x268 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_05_GPIO_MUX1_IO05			0x024 0x268 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_05_FLEXIO1_D05			0x024 0x268 0x0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B1_05_GPIO7_IO05			0x024 0x268 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B1_06_SEMC_DATA06			0x028 0x26C 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_06_FLEXPWM2_PWM0_A			0x028 0x26C 0x518 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_06_GPIO_MUX1_IO06			0x028 0x26C 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_06_FLEXIO1_D06			0x028 0x26C 0x0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B1_06_GPIO7_IO06			0x028 0x26C 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B1_07_GPIO7_IO07			0x02C 0x270 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B1_07_SEMC_DATA07			0x02C 0x270 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_07_FLEXPWM2_PWM0_B			0x02C 0x270 0x524 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_07_GPIO_MUX1_IO07			0x02C 0x270 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_07_FLEXIO1_D07			0x02C 0x270 0x0 0x8 0x0
+
+#define IOMUXC_GPIO_EMC_B1_08_SEMC_DM00				0x030 0x274 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_08_FLEXPWM2_PWM1_A			0x030 0x274 0x51C 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_08_GPIO_MUX1_IO08			0x030 0x274 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_08_FLEXIO1_D08			0x030 0x274 0x0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B1_08_GPIO7_IO08			0x030 0x274 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B1_09_SEMC_ADDR00			0x034 0x278 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_09_FLEXPWM2_PWM1_B			0x034 0x278 0x528 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_09_GPT5_CAPTURE1			0x034 0x278 0x0 0x2 0x0
+#define IOMUXC_GPIO_EMC_B1_09_GPIO_MUX1_IO09			0x034 0x278 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_09_FLEXIO1_D09			0x034 0x278 0x0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B1_09_GPIO7_IO09			0x034 0x278 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B1_10_SEMC_ADDR01			0x038 0x27C 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_10_FLEXPWM2_PWM2_A			0x038 0x27C 0x520 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_10_GPT5_CAPTURE2			0x038 0x27C 0x0 0x2 0x0
+#define IOMUXC_GPIO_EMC_B1_10_GPIO_MUX1_IO10			0x038 0x27C 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_10_FLEXIO1_D10			0x038 0x27C 0x0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B1_10_GPIO7_IO10			0x038 0x27C 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B1_11_GPIO7_IO11			0x03C 0x280 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B1_11_SEMC_ADDR02			0x03C 0x280 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_11_FLEXPWM2_PWM2_B			0x03C 0x280 0x52C 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_11_GPT5_COMPARE1			0x03C 0x280 0x0 0x2 0x0
+#define IOMUXC_GPIO_EMC_B1_11_GPIO_MUX1_IO11			0x03C 0x280 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_11_FLEXIO1_D11			0x03C 0x280 0x0 0x8 0x0
+
+#define IOMUXC_GPIO_EMC_B1_12_SEMC_ADDR03			0x040 0x284 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_12_XBAR1_INOUT04			0x040 0x284 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_12_GPT5_COMPARE2			0x040 0x284 0x0 0x2 0x0
+#define IOMUXC_GPIO_EMC_B1_12_GPIO_MUX1_IO12			0x040 0x284 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_12_FLEXIO1_D12			0x040 0x284 0x0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B1_12_GPIO7_IO12			0x040 0x284 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B1_13_SEMC_ADDR04			0x044 0x288 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_13_XBAR1_INOUT05			0x044 0x288 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_13_GPT5_COMPARE3			0x044 0x288 0x0 0x2 0x0
+#define IOMUXC_GPIO_EMC_B1_13_GPIO_MUX1_IO13			0x044 0x288 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_13_FLEXIO1_D13			0x044 0x288 0x0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B1_13_GPIO7_IO13			0x044 0x288 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B1_14_GPIO7_IO14			0x048 0x28C 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B1_14_SEMC_ADDR05			0x048 0x28C 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_14_XBAR1_INOUT06			0x048 0x28C 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_14_GPT5_CLK				0x048 0x28C 0x0 0x2 0x0
+#define IOMUXC_GPIO_EMC_B1_14_GPIO_MUX1_IO14			0x048 0x28C 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_14_FLEXIO1_D14			0x048 0x28C 0x0 0x8 0x0
+
+#define IOMUXC_GPIO_EMC_B1_15_SEMC_ADDR06			0x04C 0x290 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_15_XBAR1_INOUT07			0x04C 0x290 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_15_GPIO_MUX1_IO15			0x04C 0x290 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_15_FLEXIO1_D15			0x04C 0x290 0x0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B1_15_GPIO7_IO15			0x04C 0x290 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B1_16_SEMC_ADDR07			0x050 0x294 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_16_XBAR1_INOUT08			0x050 0x294 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_16_GPIO_MUX1_IO16			0x050 0x294 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_16_FLEXIO1_D16			0x050 0x294 0x0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B1_16_GPIO7_IO16			0x050 0x294 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B1_17_GPIO7_IO17			0x054 0x298 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B1_17_SEMC_ADDR08			0x054 0x298 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_17_FLEXPWM4_PWM3_A			0x054 0x298 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_17_TMR1_TIMER0			0x054 0x298 0x63C 0x2 0x0
+#define IOMUXC_GPIO_EMC_B1_17_GPIO_MUX1_IO17			0x054 0x298 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_17_FLEXIO1_D17			0x054 0x298 0x0 0x8 0x0
+
+#define IOMUXC_GPIO_EMC_B1_18_SEMC_ADDR09			0x058 0x29C 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_18_FLEXPWM4_PWM3_B			0x058 0x29C 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_18_TMR2_TIMER0			0x058 0x29C 0x648 0x2 0x0
+#define IOMUXC_GPIO_EMC_B1_18_GPIO_MUX1_IO18			0x058 0x29C 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_18_FLEXIO1_D18			0x058 0x29C 0x0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B1_18_GPIO7_IO18			0x058 0x29C 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B1_19_SEMC_ADDR11			0x05C 0x2A0 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_19_FLEXPWM2_PWM3_A			0x05C 0x2A0 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_19_TMR3_TIMER0			0x05C 0x2A0 0x654 0x2 0x0
+#define IOMUXC_GPIO_EMC_B1_19_GPIO_MUX1_IO19			0x05C 0x2A0 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_19_FLEXIO1_D19			0x05C 0x2A0 0x0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B1_19_GPIO7_IO19			0x05C 0x2A0 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B1_20_SEMC_ADDR12			0x060 0x2A4 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_20_FLEXPWM2_PWM3_B			0x060 0x2A4 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_20_TMR4_TIMER0			0x060 0x2A4 0x660 0x2 0x0
+#define IOMUXC_GPIO_EMC_B1_20_GPIO_MUX1_IO20			0x060 0x2A4 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_20_FLEXIO1_D20			0x060 0x2A4 0x0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B1_20_GPIO7_IO20			0x060 0x2A4 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B1_21_GPIO7_IO21			0x064 0x2A8 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B1_21_SEMC_BA0				0x064 0x2A8 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_21_FLEXPWM3_PWM3_A			0x064 0x2A8 0x53C 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_21_GPIO_MUX1_IO21			0x064 0x2A8 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_21_FLEXIO1_D21			0x064 0x2A8 0x0 0x8 0x0
+
+#define IOMUXC_GPIO_EMC_B1_22_GPIO7_IO22			0x068 0x2AC 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B1_22_SEMC_BA1				0x068 0x2AC 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_22_FLEXPWM3_PWM3_B			0x068 0x2AC 0x54C 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_22_GPIO_MUX1_IO22			0x068 0x2AC 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_22_FLEXIO1_D22			0x068 0x2AC 0x0 0x8 0x0
+
+#define IOMUXC_GPIO_EMC_B1_23_SEMC_ADDR10			0x06C 0x2B0 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_23_FLEXPWM1_PWM0_A			0x06C 0x2B0 0x500 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_23_GPIO_MUX1_IO23			0x06C 0x2B0 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_23_FLEXIO1_D23			0x06C 0x2B0 0x0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B1_23_GPIO7_IO23			0x06C 0x2B0 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B1_24_GPIO7_IO24			0x070 0x2B4 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B1_24_SEMC_CAS				0x070 0x2B4 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_24_FLEXPWM1_PWM0_B			0x070 0x2B4 0x50C 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_24_GPIO_MUX1_IO24			0x070 0x2B4 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_24_FLEXIO1_D24			0x070 0x2B4 0x0 0x8 0x0
+
+#define IOMUXC_GPIO_EMC_B1_25_GPIO7_IO25			0x074 0x2B8 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B1_25_SEMC_RAS				0x074 0x2B8 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_25_FLEXPWM1_PWM1_A			0x074 0x2B8 0x504 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_25_GPIO_MUX1_IO25			0x074 0x2B8 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_25_FLEXIO1_D25			0x074 0x2B8 0x0 0x8 0x0
+
+#define IOMUXC_GPIO_EMC_B1_26_SEMC_CLK				0x078 0x2BC 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_26_FLEXPWM1_PWM1_B			0x078 0x2BC 0x510 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_26_GPIO_MUX1_IO26			0x078 0x2BC 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_26_FLEXIO1_D26			0x078 0x2BC 0x0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B1_26_GPIO7_IO26			0x078 0x2BC 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B1_27_GPIO7_IO27			0x07C 0x2C0 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B1_27_SEMC_CKE				0x07C 0x2C0 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_27_FLEXPWM1_PWM2_A			0x07C 0x2C0 0x508 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_27_GPIO_MUX1_IO27			0x07C 0x2C0 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_27_FLEXIO1_D27			0x07C 0x2C0 0x0 0x8 0x0
+
+#define IOMUXC_GPIO_EMC_B1_28_GPIO7_IO28			0x080 0x2C4 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B1_28_SEMC_WE				0x080 0x2C4 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_28_FLEXPWM1_PWM2_B			0x080 0x2C4 0x514 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_28_GPIO_MUX1_IO28			0x080 0x2C4 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_28_FLEXIO1_D28			0x080 0x2C4 0x0 0x8 0x0
+
+#define IOMUXC_GPIO_EMC_B1_29_SEMC_CS0				0x084 0x2C8 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_29_FLEXPWM3_PWM0_A			0x084 0x2C8 0x530 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_29_GPIO_MUX1_IO29			0x084 0x2C8 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_29_FLEXIO1_D29			0x084 0x2C8 0x0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B1_29_GPIO7_IO29			0x084 0x2C8 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B1_30_SEMC_DATA08			0x088 0x2CC 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_30_FLEXPWM3_PWM0_B			0x088 0x2CC 0x540 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_30_GPIO_MUX1_IO30			0x088 0x2CC 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_30_FLEXIO1_D30			0x088 0x2CC 0x0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B1_30_GPIO7_IO30			0x088 0x2CC 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B1_31_GPIO7_IO31			0x08C 0x2D0 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B1_31_SEMC_DATA09			0x08C 0x2D0 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_31_FLEXPWM3_PWM1_A			0x08C 0x2D0 0x534 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_31_GPIO_MUX1_IO31			0x08C 0x2D0 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_31_FLEXIO1_D31			0x08C 0x2D0 0x0 0x8 0x0
+
+#define IOMUXC_GPIO_EMC_B1_32_GPIO8_IO00			0x090 0x2D4 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B1_32_SEMC_DATA10			0x090 0x2D4 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_32_FLEXPWM3_PWM1_B			0x090 0x2D4 0x544 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_32_GPIO_MUX2_IO00			0x090 0x2D4 0x0 0x5 0x0
+
+#define IOMUXC_GPIO_EMC_B1_33_SEMC_DATA11			0x094 0x2D8 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_33_FLEXPWM3_PWM2_A			0x094 0x2D8 0x538 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_33_GPIO_MUX2_IO01			0x094 0x2D8 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_33_GPIO8_IO01			0x094 0x2D8 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B1_34_GPIO8_IO02			0x098 0x2DC 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B1_34_SEMC_DATA12			0x098 0x2DC 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_34_FLEXPWM3_PWM2_B			0x098 0x2DC 0x548 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_34_GPIO_MUX2_IO02			0x098 0x2DC 0x0 0x5 0x0
+
+#define IOMUXC_GPIO_EMC_B1_35_GPIO8_IO03			0x09C 0x2E0 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B1_35_SEMC_DATA13			0x09C 0x2E0 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_35_XBAR1_INOUT09			0x09C 0x2E0 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_35_GPIO_MUX2_IO03			0x09C 0x2E0 0x0 0x5 0x0
+
+#define IOMUXC_GPIO_EMC_B1_36_SEMC_DATA14			0x0A0 0x2E4 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_36_XBAR1_INOUT10			0x0A0 0x2E4 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_36_GPIO_MUX2_IO04			0x0A0 0x2E4 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_36_GPIO8_IO04			0x0A0 0x2E4 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B1_37_GPIO8_IO05			0x0A4 0x2E8 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B1_37_SEMC_DATA15			0x0A4 0x2E8 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_37_XBAR1_INOUT11			0x0A4 0x2E8 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_37_GPIO_MUX2_IO05			0x0A4 0x2E8 0x0 0x5 0x0
+
+#define IOMUXC_GPIO_EMC_B1_38_GPIO8_IO06			0x0A8 0x2EC 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B1_38_SEMC_DM01				0x0A8 0x2EC 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_38_FLEXPWM1_PWM3_A			0x0A8 0x2EC 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_38_TMR1_TIMER1			0x0A8 0x2EC 0x640 0x2 0x0
+#define IOMUXC_GPIO_EMC_B1_38_GPIO_MUX2_IO06			0x0A8 0x2EC 0x0 0x5 0x0
+
+#define IOMUXC_GPIO_EMC_B1_39_SEMC_DQS				0x0AC 0x2F0 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_39_FLEXPWM1_PWM3_B			0x0AC 0x2F0 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_39_TMR2_TIMER1			0x0AC 0x2F0 0x64C 0x2 0x0
+#define IOMUXC_GPIO_EMC_B1_39_GPIO_MUX2_IO07			0x0AC 0x2F0 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_39_GPIO8_IO07			0x0AC 0x2F0 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B1_40_SEMC_RDY				0x0B0 0x2F4 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_40_XBAR1_INOUT12			0x0B0 0x2F4 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_40_MQS_RIGHT				0x0B0 0x2F4 0x0 0x2 0x0
+#define IOMUXC_GPIO_EMC_B1_40_LPUART6_TXD			0x0B0 0x2F4 0x0 0x3 0x0
+#define IOMUXC_GPIO_EMC_B1_40_GPIO_MUX2_IO08			0x0B0 0x2F4 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_40_ENET_1G_MDC			0x0B0 0x2F4 0x0 0x7 0x0
+#define IOMUXC_GPIO_EMC_B1_40_CCM_CLKO1				0x0B0 0x2F4 0x0 0x9 0x0
+#define IOMUXC_GPIO_EMC_B1_40_GPIO8_IO08			0x0B0 0x2F4 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B1_41_GPIO8_IO09			0x0B4 0x2F8 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B1_41_SEMC_CSX00			0x0B4 0x2F8 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B1_41_XBAR1_INOUT13			0x0B4 0x2F8 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B1_41_MQS_LEFT				0x0B4 0x2F8 0x0 0x2 0x0
+#define IOMUXC_GPIO_EMC_B1_41_LPUART6_RXD			0x0B4 0x2F8 0x0 0x3 0x0
+#define IOMUXC_GPIO_EMC_B1_41_FLEXSPI2_B_DATA07			0x0B4 0x2F8 0x0 0x4 0x0
+#define IOMUXC_GPIO_EMC_B1_41_GPIO_MUX2_IO09			0x0B4 0x2F8 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B1_41_ENET_1G_MDIO			0x0B4 0x2F8 0x4C8 0x7 0x0
+#define IOMUXC_GPIO_EMC_B1_41_CCM_CLKO2				0x0B4 0x2F8 0x0 0x9 0x0
+
+#define IOMUXC_GPIO_EMC_B2_00_SEMC_DATA16			0x0B8 0x2FC 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B2_00_CCM_ENET_REF_CLK_25M		0x0B8 0x2FC 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B2_00_TMR3_TIMER1			0x0B8 0x2FC 0x658 0x2 0x0
+#define IOMUXC_GPIO_EMC_B2_00_LPUART6_CTS_B			0x0B8 0x2FC 0x0 0x3 0x0
+#define IOMUXC_GPIO_EMC_B2_00_FLEXSPI2_B_DATA06			0x0B8 0x2FC 0x0 0x4 0x0
+#define IOMUXC_GPIO_EMC_B2_00_GPIO_MUX2_IO10			0x0B8 0x2FC 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B2_00_XBAR1_INOUT20			0x0B8 0x2FC 0x6D8 0x6 0x0
+#define IOMUXC_GPIO_EMC_B2_00_ENET_QOS_1588_EVENT1_OUT		0x0B8 0x2FC 0x0 0x7 0x0
+#define IOMUXC_GPIO_EMC_B2_00_LPSPI1_SCK			0x0B8 0x2FC 0x5D0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B2_00_LPI2C2_SCL			0x0B8 0x2FC 0x5B4 0x9 0x0
+#define IOMUXC_GPIO_EMC_B2_00_GPIO8_IO10			0x0B8 0x2FC 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B2_00_FLEXPWM3_PWM0_A			0x0B8 0x2FC 0x530 0xB 0x1
+
+#define IOMUXC_GPIO_EMC_B2_01_SEMC_DATA17			0x0BC 0x300 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B2_01_USDHC2_CD_B			0x0BC 0x300 0x6D0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B2_01_TMR4_TIMER1			0x0BC 0x300 0x664 0x2 0x0
+#define IOMUXC_GPIO_EMC_B2_01_LPUART6_RTS_B			0x0BC 0x300 0x0 0x3 0x0
+#define IOMUXC_GPIO_EMC_B2_01_FLEXSPI2_B_DATA05			0x0BC 0x300 0x0 0x4 0x0
+#define IOMUXC_GPIO_EMC_B2_01_GPIO_MUX2_IO11			0x0BC 0x300 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B2_01_XBAR1_INOUT21			0x0BC 0x300 0x6DC 0x6 0x0
+#define IOMUXC_GPIO_EMC_B2_01_ENET_QOS_1588_EVENT1_IN		0x0BC 0x300 0x0 0x7 0x0
+#define IOMUXC_GPIO_EMC_B2_01_LPSPI1_PCS0			0x0BC 0x300 0x5CC 0x8 0x0
+#define IOMUXC_GPIO_EMC_B2_01_LPI2C2_SDA			0x0BC 0x300 0x5B8 0x9 0x0
+#define IOMUXC_GPIO_EMC_B2_01_GPIO8_IO11			0x0BC 0x300 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B2_01_FLEXPWM3_PWM0_B			0x0BC 0x300 0x540 0xB 0x1
+
+#define IOMUXC_GPIO_EMC_B2_02_SEMC_DATA18			0x0C0 0x304 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B2_02_USDHC2_WP				0x0C0 0x304 0x6D4 0x1 0x0
+#define IOMUXC_GPIO_EMC_B2_02_VIDEO_MUX_CSI_DATA23		0x0C0 0x304 0x0 0x3 0x0
+#define IOMUXC_GPIO_EMC_B2_02_FLEXSPI2_B_DATA04			0x0C0 0x304 0x0 0x4 0x0
+#define IOMUXC_GPIO_EMC_B2_02_GPIO_MUX2_IO12			0x0C0 0x304 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B2_02_XBAR1_INOUT22			0x0C0 0x304 0x6E0 0x6 0x0
+#define IOMUXC_GPIO_EMC_B2_02_ENET_QOS_1588_EVENT1_AUX_IN	0x0C0 0x304 0x0 0x7 0x0
+#define IOMUXC_GPIO_EMC_B2_02_LPSPI1_SOUT			0x0C0 0x304 0x5D8 0x8 0x0
+#define IOMUXC_GPIO_EMC_B2_02_GPIO8_IO12			0x0C0 0x304 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B2_02_FLEXPWM3_PWM1_A			0x0C0 0x304 0x534 0xB 0x1
+
+#define IOMUXC_GPIO_EMC_B2_03_SEMC_DATA19			0x0C4 0x308 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B2_03_USDHC2_VSELECT			0x0C4 0x308 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B2_03_VIDEO_MUX_CSI_DATA22		0x0C4 0x308 0x0 0x3 0x0
+#define IOMUXC_GPIO_EMC_B2_03_FLEXSPI2_B_DATA03			0x0C4 0x308 0x0 0x4 0x0
+#define IOMUXC_GPIO_EMC_B2_03_GPIO_MUX2_IO13			0x0C4 0x308 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B2_03_XBAR1_INOUT23			0x0C4 0x308 0x6E4 0x6 0x0
+#define IOMUXC_GPIO_EMC_B2_03_ENET_1G_TX_DATA03			0x0C4 0x308 0x0 0x7 0x0
+#define IOMUXC_GPIO_EMC_B2_03_LPSPI1_SIN			0x0C4 0x308 0x5D4 0x8 0x0
+#define IOMUXC_GPIO_EMC_B2_03_GPIO8_IO13			0x0C4 0x308 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B2_03_FLEXPWM3_PWM1_B			0x0C4 0x308 0x544 0xB 0x1
+
+#define IOMUXC_GPIO_EMC_B2_04_SEMC_DATA20			0x0C8 0x30C 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B2_04_USDHC2_RESET_B			0x0C8 0x30C 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B2_04_SAI2_MCLK				0x0C8 0x30C 0x0 0x2 0x0
+#define IOMUXC_GPIO_EMC_B2_04_VIDEO_MUX_CSI_DATA21		0x0C8 0x30C 0x0 0x3 0x0
+#define IOMUXC_GPIO_EMC_B2_04_FLEXSPI2_B_DATA02			0x0C8 0x30C 0x0 0x4 0x0
+#define IOMUXC_GPIO_EMC_B2_04_GPIO_MUX2_IO14			0x0C8 0x30C 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B2_04_XBAR1_INOUT24			0x0C8 0x30C 0x6E8 0x6 0x0
+#define IOMUXC_GPIO_EMC_B2_04_ENET_1G_TX_DATA02			0x0C8 0x30C 0x0 0x7 0x0
+#define IOMUXC_GPIO_EMC_B2_04_LPSPI3_SCK			0x0C8 0x30C 0x600 0x8 0x0
+#define IOMUXC_GPIO_EMC_B2_04_GPIO8_IO14			0x0C8 0x30C 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B2_04_FLEXPWM3_PWM2_A			0x0C8 0x30C 0x538 0xB 0x1
+
+#define IOMUXC_GPIO_EMC_B2_05_SEMC_DATA21			0x0CC 0x310 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B2_05_GPT3_CLK				0x0CC 0x310 0x598 0x1 0x0
+#define IOMUXC_GPIO_EMC_B2_05_SAI2_RX_SYNC			0x0CC 0x310 0x0 0x2 0x0
+#define IOMUXC_GPIO_EMC_B2_05_VIDEO_MUX_CSI_DATA20		0x0CC 0x310 0x0 0x3 0x0
+#define IOMUXC_GPIO_EMC_B2_05_FLEXSPI2_B_DATA01			0x0CC 0x310 0x0 0x4 0x0
+#define IOMUXC_GPIO_EMC_B2_05_GPIO_MUX2_IO15			0x0CC 0x310 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B2_05_XBAR1_INOUT25			0x0CC 0x310 0x6EC 0x6 0x0
+#define IOMUXC_GPIO_EMC_B2_05_ENET_1G_RX_CLK			0x0CC 0x310 0x4CC 0x7 0x0
+#define IOMUXC_GPIO_EMC_B2_05_LPSPI3_PCS0			0x0CC 0x310 0x5F0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B2_05_PIT1_TRIGGER0			0x0CC 0x310 0x0 0x9 0x0
+#define IOMUXC_GPIO_EMC_B2_05_GPIO8_IO15			0x0CC 0x310 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B2_05_FLEXPWM3_PWM2_B			0x0CC 0x310 0x548 0xB 0x1
+
+#define IOMUXC_GPIO_EMC_B2_06_SEMC_DATA22			0x0D0 0x314 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B2_06_GPT3_CAPTURE1			0x0D0 0x314 0x590 0x1 0x0
+#define IOMUXC_GPIO_EMC_B2_06_GPIO8_IO16			0x0D0 0x314 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B2_06_SAI2_RX_BCLK			0x0D0 0x314 0x0 0x2 0x0
+#define IOMUXC_GPIO_EMC_B2_06_FLEXPWM3_PWM3_A			0x0D0 0x314 0x53C 0xB 0x1
+#define IOMUXC_GPIO_EMC_B2_06_VIDEO_MUX_CSI_DATA19		0x0D0 0x314 0x0 0x3 0x0
+#define IOMUXC_GPIO_EMC_B2_06_FLEXSPI2_B_DATA00			0x0D0 0x314 0x0 0x4 0x0
+#define IOMUXC_GPIO_EMC_B2_06_GPIO_MUX2_IO16			0x0D0 0x314 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B2_06_XBAR1_INOUT26			0x0D0 0x314 0x6F0 0x6 0x0
+#define IOMUXC_GPIO_EMC_B2_06_ENET_1G_TX_ER			0x0D0 0x314 0x0 0x7 0x0
+#define IOMUXC_GPIO_EMC_B2_06_LPSPI3_SOUT			0x0D0 0x314 0x608 0x8 0x0
+#define IOMUXC_GPIO_EMC_B2_06_PIT1_TRIGGER1			0x0D0 0x314 0x0 0x9 0x0
+
+#define IOMUXC_GPIO_EMC_B2_07_SEMC_DATA23			0x0D4 0x318 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B2_07_GPT3_CAPTURE2			0x0D4 0x318 0x594 0x1 0x0
+#define IOMUXC_GPIO_EMC_B2_07_SAI2_RX_DATA			0x0D4 0x318 0x0 0x2 0x0
+#define IOMUXC_GPIO_EMC_B2_07_VIDEO_MUX_CSI_DATA18		0x0D4 0x318 0x0 0x3 0x0
+#define IOMUXC_GPIO_EMC_B2_07_FLEXSPI2_B_DQS			0x0D4 0x318 0x0 0x4 0x0
+#define IOMUXC_GPIO_EMC_B2_07_GPIO_MUX2_IO17			0x0D4 0x318 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B2_07_XBAR1_INOUT27			0x0D4 0x318 0x6F4 0x6 0x0
+#define IOMUXC_GPIO_EMC_B2_07_ENET_1G_RX_DATA03			0x0D4 0x318 0x4DC 0x7 0x0
+#define IOMUXC_GPIO_EMC_B2_07_LPSPI3_SIN			0x0D4 0x318 0x604 0x8 0x0
+#define IOMUXC_GPIO_EMC_B2_07_PIT1_TRIGGER2			0x0D4 0x318 0x0 0x9 0x0
+#define IOMUXC_GPIO_EMC_B2_07_GPIO8_IO17			0x0D4 0x318 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B2_07_FLEXPWM3_PWM3_B			0x0D4 0x318 0x54C 0xB 0x1
+
+#define IOMUXC_GPIO_EMC_B2_08_SEMC_DM02				0x0D8 0x31C 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B2_08_GPT3_COMPARE1			0x0D8 0x31C 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B2_08_SAI2_TX_DATA			0x0D8 0x31C 0x0 0x2 0x0
+#define IOMUXC_GPIO_EMC_B2_08_VIDEO_MUX_CSI_DATA17		0x0D8 0x31C 0x0 0x3 0x0
+#define IOMUXC_GPIO_EMC_B2_08_FLEXSPI2_B_SS0_B			0x0D8 0x31C 0x0 0x4 0x0
+#define IOMUXC_GPIO_EMC_B2_08_GPIO_MUX2_IO18			0x0D8 0x31C 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B2_08_XBAR1_INOUT28			0x0D8 0x31C 0x6F8 0x6 0x0
+#define IOMUXC_GPIO_EMC_B2_08_ENET_1G_RX_DATA02			0x0D8 0x31C 0x4D8 0x7 0x0
+#define IOMUXC_GPIO_EMC_B2_08_LPSPI3_PCS1			0x0D8 0x31C 0x5F4 0x8 0x0
+#define IOMUXC_GPIO_EMC_B2_08_PIT1_TRIGGER3			0x0D8 0x31C 0x0 0x9 0x0
+#define IOMUXC_GPIO_EMC_B2_08_GPIO8_IO18			0x0D8 0x31C 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B2_09_GPIO8_IO19			0x0DC 0x320 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B2_09_SEMC_DATA24			0x0DC 0x320 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B2_09_GPT3_COMPARE2			0x0DC 0x320 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B2_09_SAI2_TX_BCLK			0x0DC 0x320 0x0 0x2 0x0
+#define IOMUXC_GPIO_EMC_B2_09_VIDEO_MUX_CSI_DATA16		0x0DC 0x320 0x0 0x3 0x0
+#define IOMUXC_GPIO_EMC_B2_09_FLEXSPI2_B_SCLK			0x0DC 0x320 0x0 0x4 0x0
+#define IOMUXC_GPIO_EMC_B2_09_GPIO_MUX2_IO19			0x0DC 0x320 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B2_09_XBAR1_INOUT29			0x0DC 0x320 0x6FC 0x6 0x0
+#define IOMUXC_GPIO_EMC_B2_09_ENET_1G_CRS			0x0DC 0x320 0x0 0x7 0x0
+#define IOMUXC_GPIO_EMC_B2_09_LPSPI3_PCS2			0x0DC 0x320 0x5F8 0x8 0x0
+#define IOMUXC_GPIO_EMC_B2_09_TMR1_TIMER0			0x0DC 0x320 0x63C 0x9 0x1
+
+#define IOMUXC_GPIO_EMC_B2_10_GPIO8_IO20			0x0E0 0x324 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B2_10_SEMC_DATA25			0x0E0 0x324 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B2_10_GPT3_COMPARE3			0x0E0 0x324 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B2_10_SAI2_TX_SYNC			0x0E0 0x324 0x0 0x2 0x0
+#define IOMUXC_GPIO_EMC_B2_10_VIDEO_MUX_CSI_FIELD		0x0E0 0x324 0x0 0x3 0x0
+#define IOMUXC_GPIO_EMC_B2_10_FLEXSPI2_A_SCLK			0x0E0 0x324 0x58C 0x4 0x0
+#define IOMUXC_GPIO_EMC_B2_10_GPIO_MUX2_IO20			0x0E0 0x324 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B2_10_XBAR1_INOUT30			0x0E0 0x324 0x700 0x6 0x0
+#define IOMUXC_GPIO_EMC_B2_10_ENET_1G_COL			0x0E0 0x324 0x0 0x7 0x0
+#define IOMUXC_GPIO_EMC_B2_10_LPSPI3_PCS3			0x0E0 0x324 0x5FC 0x8 0x0
+#define IOMUXC_GPIO_EMC_B2_10_TMR1_TIMER1			0x0E0 0x324 0x640 0x9 0x1
+
+#define IOMUXC_GPIO_EMC_B2_11_SEMC_DATA26			0x0E4 0x328 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B2_11_SPDIF_IN				0x0E4 0x328 0x6B4 0x1 0x0
+#define IOMUXC_GPIO_EMC_B2_11_ENET_1G_TX_DATA00			0x0E4 0x328 0x0 0x2 0x0
+#define IOMUXC_GPIO_EMC_B2_11_SAI3_RX_SYNC			0x0E4 0x328 0x0 0x3 0x0
+#define IOMUXC_GPIO_EMC_B2_11_FLEXSPI2_A_SS0_B			0x0E4 0x328 0x0 0x4 0x0
+#define IOMUXC_GPIO_EMC_B2_11_GPIO_MUX2_IO21			0x0E4 0x328 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B2_11_XBAR1_INOUT31			0x0E4 0x328 0x704 0x6 0x0
+#define IOMUXC_GPIO_EMC_B2_11_EMVSIM1_IO			0x0E4 0x328 0x69C 0x8 0x0
+#define IOMUXC_GPIO_EMC_B2_11_TMR1_TIMER2			0x0E4 0x328 0x644 0x9 0x0
+#define IOMUXC_GPIO_EMC_B2_11_GPIO8_IO21			0x0E4 0x328 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B2_12_SEMC_DATA27			0x0E8 0x32C 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B2_12_SPDIF_OUT				0x0E8 0x32C 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B2_12_ENET_1G_TX_DATA01			0x0E8 0x32C 0x0 0x2 0x0
+#define IOMUXC_GPIO_EMC_B2_12_SAI3_RX_BCLK			0x0E8 0x32C 0x0 0x3 0x0
+#define IOMUXC_GPIO_EMC_B2_12_FLEXSPI2_A_DQS			0x0E8 0x32C 0x0 0x4 0x0
+#define IOMUXC_GPIO_EMC_B2_12_GPIO_MUX2_IO22			0x0E8 0x32C 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B2_12_XBAR1_INOUT32			0x0E8 0x32C 0x708 0x6 0x0
+#define IOMUXC_GPIO_EMC_B2_12_EMVSIM1_CLK			0x0E8 0x32C 0x0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B2_12_TMR1_TIMER3			0x0E8 0x32C 0x0 0x9 0x0
+#define IOMUXC_GPIO_EMC_B2_12_GPIO8_IO22			0x0E8 0x32C 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B2_13_GPIO8_IO23			0x0EC 0x330 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B2_13_SEMC_DATA28			0x0EC 0x330 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B2_13_ENET_1G_TX_EN			0x0EC 0x330 0x0 0x2 0x0
+#define IOMUXC_GPIO_EMC_B2_13_SAI3_RX_DATA			0x0EC 0x330 0x0 0x3 0x0
+#define IOMUXC_GPIO_EMC_B2_13_FLEXSPI2_A_DATA00			0x0EC 0x330 0x57C 0x4 0x0
+#define IOMUXC_GPIO_EMC_B2_13_GPIO_MUX2_IO23			0x0EC 0x330 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B2_13_XBAR1_INOUT33			0x0EC 0x330 0x70C 0x6 0x0
+#define IOMUXC_GPIO_EMC_B2_13_EMVSIM1_RST			0x0EC 0x330 0x0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B2_13_TMR2_TIMER0			0x0EC 0x330 0x648 0x9 0x1
+
+#define IOMUXC_GPIO_EMC_B2_14_SEMC_DATA29			0x0F0 0x334 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B2_14_ENET_1G_TX_CLK_IO			0x0F0 0x334 0x4E8 0x2 0x0
+#define IOMUXC_GPIO_EMC_B2_14_SAI3_TX_DATA			0x0F0 0x334 0x0 0x3 0x0
+#define IOMUXC_GPIO_EMC_B2_14_FLEXSPI2_A_DATA01			0x0F0 0x334 0x580 0x4 0x0
+#define IOMUXC_GPIO_EMC_B2_14_GPIO_MUX2_IO24			0x0F0 0x334 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B2_14_XBAR1_INOUT34			0x0F0 0x334 0x710 0x6 0x0
+#define IOMUXC_GPIO_EMC_B2_14_SFA_ipp_do_atx_clk_under_test	0x0F0 0x334 0x0 0x7 0x0
+#define IOMUXC_GPIO_EMC_B2_14_EMVSIM1_SVEN			0x0F0 0x334 0x0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B2_14_TMR2_TIMER1			0x0F0 0x334 0x64C 0x9 0x1
+#define IOMUXC_GPIO_EMC_B2_14_GPIO8_IO24			0x0F0 0x334 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B2_15_SEMC_DATA30			0x0F4 0x338 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B2_15_ENET_1G_RX_DATA00			0x0F4 0x338 0x4D0 0x2 0x0
+#define IOMUXC_GPIO_EMC_B2_15_SAI3_TX_BCLK			0x0F4 0x338 0x0 0x3 0x0
+#define IOMUXC_GPIO_EMC_B2_15_FLEXSPI2_A_DATA02			0x0F4 0x338 0x584 0x4 0x0
+#define IOMUXC_GPIO_EMC_B2_15_GPIO_MUX2_IO25			0x0F4 0x338 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B2_15_XBAR1_INOUT35			0x0F4 0x338 0x714 0x6 0x0
+#define IOMUXC_GPIO_EMC_B2_15_EMVSIM1_PD			0x0F4 0x338 0x6A0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B2_15_TMR2_TIMER2			0x0F4 0x338 0x650 0x9 0x0
+#define IOMUXC_GPIO_EMC_B2_15_GPIO8_IO25			0x0F4 0x338 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B2_16_GPIO8_IO26			0x0F8 0x33C 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B2_16_SEMC_DATA31			0x0F8 0x33C 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B2_16_XBAR1_INOUT14			0x0F8 0x33C 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B2_16_ENET_1G_RX_DATA01			0x0F8 0x33C 0x4D4 0x2 0x0
+#define IOMUXC_GPIO_EMC_B2_16_SAI3_TX_SYNC			0x0F8 0x33C 0x0 0x3 0x0
+#define IOMUXC_GPIO_EMC_B2_16_FLEXSPI2_A_DATA03			0x0F8 0x33C 0x588 0x4 0x0
+#define IOMUXC_GPIO_EMC_B2_16_GPIO_MUX2_IO26			0x0F8 0x33C 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B2_16_EMVSIM1_POWER_FAIL		0x0F8 0x33C 0x6A4 0x8 0x0
+#define IOMUXC_GPIO_EMC_B2_16_TMR2_TIMER3			0x0F8 0x33C 0x0 0x9 0x0
+
+#define IOMUXC_GPIO_EMC_B2_17_SEMC_DM03				0x0FC 0x340 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B2_17_XBAR1_INOUT15			0x0FC 0x340 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B2_17_ENET_1G_RX_EN			0x0FC 0x340 0x4E0 0x2 0x0
+#define IOMUXC_GPIO_EMC_B2_17_SAI3_MCLK				0x0FC 0x340 0x0 0x3 0x0
+#define IOMUXC_GPIO_EMC_B2_17_FLEXSPI2_A_DATA04			0x0FC 0x340 0x0 0x4 0x0
+#define IOMUXC_GPIO_EMC_B2_17_GPIO_MUX2_IO27			0x0FC 0x340 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B2_17_WDOG1_ANY				0x0FC 0x340 0x0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B2_17_TMR3_TIMER0			0x0FC 0x340 0x654 0x9 0x1
+#define IOMUXC_GPIO_EMC_B2_17_GPIO8_IO27			0x0FC 0x340 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B2_18_SEMC_DQS4				0x100 0x344 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B2_18_XBAR1_INOUT16			0x100 0x344 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B2_18_ENET_1G_RX_ER			0x100 0x344 0x4E4 0x2 0x0
+#define IOMUXC_GPIO_EMC_B2_18_EWM_OUT_B				0x100 0x344 0x0 0x3 0x0
+#define IOMUXC_GPIO_EMC_B2_18_FLEXSPI2_A_DATA05			0x100 0x344 0x0 0x4 0x0
+#define IOMUXC_GPIO_EMC_B2_18_GPIO_MUX2_IO28			0x100 0x344 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B2_18_FLEXSPI1_A_DQS			0x100 0x344 0x550 0x6 0x0
+#define IOMUXC_GPIO_EMC_B2_18_WDOG1_B				0x100 0x344 0x0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B2_18_TMR3_TIMER1			0x100 0x344 0x658 0x9 0x1
+#define IOMUXC_GPIO_EMC_B2_18_GPIO8_IO28			0x100 0x344 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_EMC_B2_19_GPIO8_IO29			0x104 0x348 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B2_19_SEMC_CLKX00			0x104 0x348 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B2_19_ENET_MDC				0x104 0x348 0x0 0x1 0x0
+#define IOMUXC_GPIO_EMC_B2_19_ENET_1G_MDC			0x104 0x348 0x0 0x2 0x0
+#define IOMUXC_GPIO_EMC_B2_19_ENET_1G_REF_CLK			0x104 0x348 0x4C4 0x3 0x0
+#define IOMUXC_GPIO_EMC_B2_19_FLEXSPI2_A_DATA06			0x104 0x348 0x0 0x4 0x0
+#define IOMUXC_GPIO_EMC_B2_19_GPIO_MUX2_IO29			0x104 0x348 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B2_19_ENET_QOS_MDC			0x104 0x348 0x0 0x8 0x0
+#define IOMUXC_GPIO_EMC_B2_19_TMR3_TIMER2			0x104 0x348 0x65C 0x9 0x0
+
+#define IOMUXC_GPIO_EMC_B2_20_GPIO8_IO30			0x108 0x34C 0x0 0xA 0x0
+#define IOMUXC_GPIO_EMC_B2_20_SEMC_CLKX01			0x108 0x34C 0x0 0x0 0x0
+#define IOMUXC_GPIO_EMC_B2_20_ENET_MDIO				0x108 0x34C 0x4AC 0x1 0x0
+#define IOMUXC_GPIO_EMC_B2_20_ENET_1G_MDIO			0x108 0x34C 0x4C8 0x2 0x1
+#define IOMUXC_GPIO_EMC_B2_20_ENET_QOS_REF_CLK			0x108 0x34C 0x4A0 0x3 0x0
+#define IOMUXC_GPIO_EMC_B2_20_FLEXSPI2_A_DATA07			0x108 0x34C 0x0 0x4 0x0
+#define IOMUXC_GPIO_EMC_B2_20_GPIO_MUX2_IO30			0x108 0x34C 0x0 0x5 0x0
+#define IOMUXC_GPIO_EMC_B2_20_ENET_QOS_MDIO			0x108 0x34C 0x4EC 0x8 0x0
+#define IOMUXC_GPIO_EMC_B2_20_TMR3_TIMER3			0x108 0x34C 0x0 0x9 0x0
+
+#define IOMUXC_GPIO_AD_00_GPIO8_IO31				0x10C 0x350 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_00_EMVSIM1_IO				0x10C 0x350 0x69C 0x0 0x1
+#define IOMUXC_GPIO_AD_00_FLEXCAN2_TX				0x10C 0x350 0x0 0x1 0x0
+#define IOMUXC_GPIO_AD_00_ENET_1G_1588_EVENT1_IN		0x10C 0x350 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_00_GPT2_CAPTURE1				0x10C 0x350 0x0 0x3 0x0
+#define IOMUXC_GPIO_AD_00_FLEXPWM1_PWM0_A			0x10C 0x350 0x500 0x4 0x1
+#define IOMUXC_GPIO_AD_00_GPIO_MUX2_IO31			0x10C 0x350 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_00_LPUART7_TXD				0x10C 0x350 0x630 0x6 0x0
+#define IOMUXC_GPIO_AD_00_FLEXIO2_D00				0x10C 0x350 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_00_FLEXSPI2_B_SS1_B			0x10C 0x350 0x0 0x9 0x0
+
+#define IOMUXC_GPIO_AD_01_GPIO9_IO00				0x110 0x354 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_01_EMVSIM1_CLK				0x110 0x354 0x0 0x0 0x0
+#define IOMUXC_GPIO_AD_01_FLEXCAN2_RX				0x110 0x354 0x49C 0x1 0x0
+#define IOMUXC_GPIO_AD_01_ENET_1G_1588_EVENT1_OUT		0x110 0x354 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_01_GPT2_CAPTURE2				0x110 0x354 0x0 0x3 0x0
+#define IOMUXC_GPIO_AD_01_FLEXPWM1_PWM0_B			0x110 0x354 0x50C 0x4 0x1
+#define IOMUXC_GPIO_AD_01_GPIO_MUX3_IO00			0x110 0x354 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_01_LPUART7_RXD				0x110 0x354 0x62C 0x6 0x0
+#define IOMUXC_GPIO_AD_01_FLEXIO2_D01				0x110 0x354 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_01_FLEXSPI2_A_SS1_B			0x110 0x354 0x0 0x9 0x0
+
+#define IOMUXC_GPIO_AD_02_GPIO9_IO01				0x114 0x358 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_02_EMVSIM1_RST				0x114 0x358 0x0 0x0 0x0
+#define IOMUXC_GPIO_AD_02_LPUART7_CTS_B				0x114 0x358 0x0 0x1 0x0
+#define IOMUXC_GPIO_AD_02_ENET_1G_1588_EVENT2_IN		0x114 0x358 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_02_GPT2_COMPARE1				0x114 0x358 0x0 0x3 0x0
+#define IOMUXC_GPIO_AD_02_FLEXPWM1_PWM1_A			0x114 0x358 0x504 0x4 0x1
+#define IOMUXC_GPIO_AD_02_GPIO_MUX3_IO01			0x114 0x358 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_02_LPUART8_TXD				0x114 0x358 0x638 0x6 0x0
+#define IOMUXC_GPIO_AD_02_FLEXIO2_D02				0x114 0x358 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_02_VIDEO_MUX_EXT_DCIC1			0x114 0x358 0x0 0x9 0x0
+
+#define IOMUXC_GPIO_AD_03_GPIO9_IO02				0x118 0x35C 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_03_EMVSIM1_SVEN				0x118 0x35C 0x0 0x0 0x0
+#define IOMUXC_GPIO_AD_03_LPUART7_RTS_B				0x118 0x35C 0x0 0x1 0x0
+#define IOMUXC_GPIO_AD_03_ENET_1G_1588_EVENT2_OUT		0x118 0x35C 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_03_GPT2_COMPARE2				0x118 0x35C 0x0 0x3 0x0
+#define IOMUXC_GPIO_AD_03_FLEXPWM1_PWM1_B			0x118 0x35C 0x510 0x4 0x1
+#define IOMUXC_GPIO_AD_03_GPIO_MUX3_IO02			0x118 0x35C 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_03_LPUART8_RXD				0x118 0x35C 0x634 0x6 0x0
+#define IOMUXC_GPIO_AD_03_FLEXIO2_D03				0x118 0x35C 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_03_VIDEO_MUX_EXT_DCIC2			0x118 0x35C 0x0 0x9 0x0
+
+#define IOMUXC_GPIO_AD_04_EMVSIM1_PD				0x11C 0x360 0x6A0 0x0 0x1
+#define IOMUXC_GPIO_AD_04_LPUART8_CTS_B				0x11C 0x360 0x0 0x1 0x0
+#define IOMUXC_GPIO_AD_04_ENET_1G_1588_EVENT3_IN		0x11C 0x360 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_04_GPT2_COMPARE3				0x11C 0x360 0x0 0x3 0x0
+#define IOMUXC_GPIO_AD_04_FLEXPWM1_PWM2_A			0x11C 0x360 0x508 0x4 0x1
+#define IOMUXC_GPIO_AD_04_GPIO_MUX3_IO03			0x11C 0x360 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_04_WDOG1_B				0x11C 0x360 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_04_FLEXIO2_D04				0x11C 0x360 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_04_TMR4_TIMER0				0x11C 0x360 0x660 0x9 0x1
+#define IOMUXC_GPIO_AD_04_GPIO9_IO03				0x11C 0x360 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_AD_05_EMVSIM1_POWER_FAIL			0x120 0x364 0x6A4 0x0 0x1
+#define IOMUXC_GPIO_AD_05_LPUART8_RTS_B				0x120 0x364 0x0 0x1 0x0
+#define IOMUXC_GPIO_AD_05_ENET_1G_1588_EVENT3_OUT		0x120 0x364 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_05_GPT2_CLK				0x120 0x364 0x0 0x3 0x0
+#define IOMUXC_GPIO_AD_05_FLEXPWM1_PWM2_B			0x120 0x364 0x514 0x4 0x1
+#define IOMUXC_GPIO_AD_05_GPIO_MUX3_IO04			0x120 0x364 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_05_WDOG2_B				0x120 0x364 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_05_FLEXIO2_D05				0x120 0x364 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_05_TMR4_TIMER1				0x120 0x364 0x664 0x9 0x1
+#define IOMUXC_GPIO_AD_05_GPIO9_IO04				0x120 0x364 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_AD_06_USB_OTG2_OC				0x124 0x368 0x6B8 0x0 0x0
+#define IOMUXC_GPIO_AD_06_FLEXCAN1_TX				0x124 0x368 0x0 0x1 0x0
+#define IOMUXC_GPIO_AD_06_EMVSIM2_IO				0x124 0x368 0x6A8 0x2 0x0
+#define IOMUXC_GPIO_AD_06_GPT3_CAPTURE1				0x124 0x368 0x590 0x3 0x1
+#define IOMUXC_GPIO_AD_06_VIDEO_MUX_CSI_DATA15			0x124 0x368 0x0 0x4 0x0
+#define IOMUXC_GPIO_AD_06_GPIO_MUX3_IO05			0x124 0x368 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_06_ENET_1588_EVENT1_IN			0x124 0x368 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_06_FLEXIO2_D06				0x124 0x368 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_06_TMR4_TIMER2				0x124 0x368 0x668 0x9 0x0
+#define IOMUXC_GPIO_AD_06_GPIO9_IO05				0x124 0x368 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_06_FLEXPWM1_PWM0_X			0x124 0x368 0x0 0xB 0x0
+
+#define IOMUXC_GPIO_AD_07_USB_OTG2_PWR				0x128 0x36C 0x0 0x0 0x0
+#define IOMUXC_GPIO_AD_07_FLEXCAN1_RX				0x128 0x36C 0x498 0x1 0x0
+#define IOMUXC_GPIO_AD_07_EMVSIM2_CLK				0x128 0x36C 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_07_GPT3_CAPTURE2				0x128 0x36C 0x594 0x3 0x1
+#define IOMUXC_GPIO_AD_07_VIDEO_MUX_CSI_DATA14			0x128 0x36C 0x0 0x4 0x0
+#define IOMUXC_GPIO_AD_07_GPIO_MUX3_IO06			0x128 0x36C 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_07_ENET_1588_EVENT1_OUT			0x128 0x36C 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_07_FLEXIO2_D07				0x128 0x36C 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_07_TMR4_TIMER3				0x128 0x36C 0x0 0x9 0x0
+#define IOMUXC_GPIO_AD_07_GPIO9_IO06				0x128 0x36C 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_07_FLEXPWM1_PWM1_X			0x128 0x36C 0x0 0xB 0x0
+
+#define IOMUXC_GPIO_AD_08_USBPHY2_OTG_ID			0x12C 0x370 0x6C4 0x0 0x0
+#define IOMUXC_GPIO_AD_08_LPI2C1_SCL				0x12C 0x370 0x5AC 0x1 0x0
+#define IOMUXC_GPIO_AD_08_EMVSIM2_RST				0x12C 0x370 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_08_GPT3_COMPARE1				0x12C 0x370 0x0 0x3 0x0
+#define IOMUXC_GPIO_AD_08_VIDEO_MUX_CSI_DATA13			0x12C 0x370 0x0 0x4 0x0
+#define IOMUXC_GPIO_AD_08_GPIO_MUX3_IO07			0x12C 0x370 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_08_ENET_1588_EVENT2_IN			0x12C 0x370 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_08_FLEXIO2_D08				0x12C 0x370 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_08_GPIO9_IO07				0x12C 0x370 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_08_FLEXPWM1_PWM2_X			0x12C 0x370 0x0 0xB 0x0
+
+#define IOMUXC_GPIO_AD_09_USBPHY1_OTG_ID			0x130 0x374 0x6C0 0x0 0x0
+#define IOMUXC_GPIO_AD_09_LPI2C1_SDA				0x130 0x374 0x5B0 0x1 0x0
+#define IOMUXC_GPIO_AD_09_EMVSIM2_SVEN				0x130 0x374 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_09_GPT3_COMPARE2				0x130 0x374 0x0 0x3 0x0
+#define IOMUXC_GPIO_AD_09_VIDEO_MUX_CSI_DATA12			0x130 0x374 0x0 0x4 0x0
+#define IOMUXC_GPIO_AD_09_GPIO_MUX3_IO08			0x130 0x374 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_09_ENET_1588_EVENT2_OUT			0x130 0x374 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_09_FLEXIO2_D09				0x130 0x374 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_09_GPIO9_IO08				0x130 0x374 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_09_FLEXPWM1_PWM3_X			0x130 0x374 0x0 0xB 0x0
+
+#define IOMUXC_GPIO_AD_10_USB_OTG1_PWR				0x134 0x378 0x0 0x0 0x0
+#define IOMUXC_GPIO_AD_10_LPI2C1_SCLS				0x134 0x378 0x0 0x1 0x0
+#define IOMUXC_GPIO_AD_10_EMVSIM2_PD				0x134 0x378 0x6AC 0x2 0x0
+#define IOMUXC_GPIO_AD_10_GPT3_COMPARE3				0x134 0x378 0x0 0x3 0x0
+#define IOMUXC_GPIO_AD_10_VIDEO_MUX_CSI_DATA11			0x134 0x378 0x0 0x4 0x0
+#define IOMUXC_GPIO_AD_10_GPIO_MUX3_IO09			0x134 0x378 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_10_ENET_1588_EVENT3_IN			0x134 0x378 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_10_FLEXIO2_D10				0x134 0x378 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_10_GPIO9_IO09				0x134 0x378 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_10_FLEXPWM2_PWM0_X			0x134 0x378 0x0 0xB 0x0
+
+#define IOMUXC_GPIO_AD_11_USB_OTG1_OC				0x138 0x37C 0x6BC 0x0 0x0
+#define IOMUXC_GPIO_AD_11_LPI2C1_SDAS				0x138 0x37C 0x0 0x1 0x0
+#define IOMUXC_GPIO_AD_11_EMVSIM2_POWER_FAIL			0x138 0x37C 0x6B0 0x2 0x0
+#define IOMUXC_GPIO_AD_11_GPT3_CLK				0x138 0x37C 0x598 0x3 0x1
+#define IOMUXC_GPIO_AD_11_VIDEO_MUX_CSI_DATA10			0x138 0x37C 0x0 0x4 0x0
+#define IOMUXC_GPIO_AD_11_GPIO_MUX3_IO10			0x138 0x37C 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_11_ENET_1588_EVENT3_OUT			0x138 0x37C 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_11_FLEXIO2_D11				0x138 0x37C 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_11_GPIO9_IO10				0x138 0x37C 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_11_FLEXPWM2_PWM1_X			0x138 0x37C 0x0 0xB 0x0
+
+#define IOMUXC_GPIO_AD_12_SPDIF_LOCK				0x13C 0x380 0x0 0x0 0x0
+#define IOMUXC_GPIO_AD_12_LPI2C1_HREQ				0x13C 0x380 0x0 0x1 0x0
+#define IOMUXC_GPIO_AD_12_GPT1_CAPTURE1				0x13C 0x380 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_12_FLEXSPI1_B_DATA03			0x13C 0x380 0x570 0x3 0x0
+#define IOMUXC_GPIO_AD_12_VIDEO_MUX_CSI_PIXCLK			0x13C 0x380 0x0 0x4 0x0
+#define IOMUXC_GPIO_AD_12_GPIO_MUX3_IO11			0x13C 0x380 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_12_ENET_TX_DATA03			0x13C 0x380 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_12_FLEXIO2_D12				0x13C 0x380 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_12_EWM_OUT_B				0x13C 0x380 0x0 0x9 0x0
+#define IOMUXC_GPIO_AD_12_GPIO9_IO11				0x13C 0x380 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_12_FLEXPWM2_PWM2_X			0x13C 0x380 0x0 0xB 0x0
+
+#define IOMUXC_GPIO_AD_13_SPDIF_SR_CLK				0x140 0x384 0x0 0x0 0x0
+#define IOMUXC_GPIO_AD_13_PIT1_TRIGGER0				0x140 0x384 0x0 0x1 0x0
+#define IOMUXC_GPIO_AD_13_GPT1_CAPTURE2				0x140 0x384 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_13_FLEXSPI1_B_DATA02			0x140 0x384 0x56C 0x3 0x0
+#define IOMUXC_GPIO_AD_13_VIDEO_MUX_CSI_MCLK			0x140 0x384 0x0 0x4 0x0
+#define IOMUXC_GPIO_AD_13_GPIO_MUX3_IO12			0x140 0x384 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_13_ENET_TX_DATA02			0x140 0x384 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_13_FLEXIO2_D13				0x140 0x384 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_13_REF_CLK_32K				0x140 0x384 0x0 0x9 0x0
+#define IOMUXC_GPIO_AD_13_GPIO9_IO12				0x140 0x384 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_13_FLEXPWM2_PWM3_X			0x140 0x384 0x0 0xB 0x0
+
+#define IOMUXC_GPIO_AD_14_SPDIF_EXT_CLK				0x144 0x388 0x0 0x0 0x0
+#define IOMUXC_GPIO_AD_14_REF_CLK_24M				0x144 0x388 0x0 0x1 0x0
+#define IOMUXC_GPIO_AD_14_GPT1_COMPARE1				0x144 0x388 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_14_FLEXSPI1_B_DATA01			0x144 0x388 0x568 0x3 0x0
+#define IOMUXC_GPIO_AD_14_VIDEO_MUX_CSI_VSYNC			0x144 0x388 0x0 0x4 0x0
+#define IOMUXC_GPIO_AD_14_GPIO_MUX3_IO13			0x144 0x388 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_14_ENET_RX_CLK				0x144 0x388 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_14_FLEXIO2_D14				0x144 0x388 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_14_CCM_ENET_REF_CLK_25M			0x144 0x388 0x0 0x9 0x0
+#define IOMUXC_GPIO_AD_14_GPIO9_IO13				0x144 0x388 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_14_FLEXPWM3_PWM0_X			0x144 0x388 0x0 0xB 0x0
+
+#define IOMUXC_GPIO_AD_15_GPIO9_IO14				0x148 0x38C 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_15_FLEXPWM3_PWM1_X			0x148 0x38C 0x0 0xB 0x0
+#define IOMUXC_GPIO_AD_15_SPDIF_IN				0x148 0x38C 0x6B4 0x0 0x1
+#define IOMUXC_GPIO_AD_15_LPUART10_TXD				0x148 0x38C 0x628 0x1 0x0
+#define IOMUXC_GPIO_AD_15_GPT1_COMPARE2				0x148 0x38C 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_15_FLEXSPI1_B_DATA00			0x148 0x38C 0x564 0x3 0x0
+#define IOMUXC_GPIO_AD_15_VIDEO_MUX_CSI_HSYNC			0x148 0x38C 0x0 0x4 0x0
+#define IOMUXC_GPIO_AD_15_GPIO_MUX3_IO14			0x148 0x38C 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_15_ENET_TX_ER				0x148 0x38C 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_15_FLEXIO2_D15				0x148 0x38C 0x0 0x8 0x0
+
+#define IOMUXC_GPIO_AD_16_SPDIF_OUT				0x14C 0x390 0x0 0x0 0x0
+#define IOMUXC_GPIO_AD_16_LPUART10_RXD				0x14C 0x390 0x624 0x1 0x0
+#define IOMUXC_GPIO_AD_16_GPT1_COMPARE3				0x14C 0x390 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_16_FLEXSPI1_B_SCLK			0x14C 0x390 0x578 0x3 0x0
+#define IOMUXC_GPIO_AD_16_VIDEO_MUX_CSI_DATA09			0x14C 0x390 0x0 0x4 0x0
+#define IOMUXC_GPIO_AD_16_GPIO_MUX3_IO15			0x14C 0x390 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_16_ENET_RX_DATA03			0x14C 0x390 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_16_FLEXIO2_D16				0x14C 0x390 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_16_ENET_1G_MDC				0x14C 0x390 0x0 0x9 0x0
+#define IOMUXC_GPIO_AD_16_GPIO9_IO15				0x14C 0x390 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_16_FLEXPWM3_PWM2_X			0x14C 0x390 0x0 0xB 0x0
+
+#define IOMUXC_GPIO_AD_17_SAI1_MCLK				0x150 0x394 0x66C 0x0 0x0
+#define IOMUXC_GPIO_AD_17_ACMP1_OUT				0x150 0x394 0x0 0x1 0x0
+#define IOMUXC_GPIO_AD_17_GPT1_CLK				0x150 0x394 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_17_FLEXSPI1_A_DQS			0x150 0x394 0x550 0x3 0x1
+#define IOMUXC_GPIO_AD_17_VIDEO_MUX_CSI_DATA08			0x150 0x394 0x0 0x4 0x0
+#define IOMUXC_GPIO_AD_17_GPIO_MUX3_IO16			0x150 0x394 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_17_ENET_RX_DATA02			0x150 0x394 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_17_FLEXIO2_D17				0x150 0x394 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_17_ENET_1G_MDIO				0x150 0x394 0x4C8 0x9 0x2
+#define IOMUXC_GPIO_AD_17_GPIO9_IO16				0x150 0x394 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_17_FLEXPWM3_PWM3_X			0x150 0x394 0x0 0xB 0x0
+
+#define IOMUXC_GPIO_AD_18_GPIO9_IO17				0x154 0x398 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_18_FLEXPWM4_PWM0_X			0x154 0x398 0x0 0xB 0x0
+#define IOMUXC_GPIO_AD_18_SAI1_RX_SYNC				0x154 0x398 0x678 0x0 0x0
+#define IOMUXC_GPIO_AD_18_ACMP2_OUT				0x154 0x398 0x0 0x1 0x0
+#define IOMUXC_GPIO_AD_18_LPSPI1_PCS1				0x154 0x398 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_18_FLEXSPI1_A_SS0_B			0x154 0x398 0x0 0x3 0x0
+#define IOMUXC_GPIO_AD_18_VIDEO_MUX_CSI_DATA07			0x154 0x398 0x0 0x4 0x0
+#define IOMUXC_GPIO_AD_18_GPIO_MUX3_IO17			0x154 0x398 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_18_ENET_CRS				0x154 0x398 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_18_FLEXIO2_D18				0x154 0x398 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_18_LPI2C2_SCL				0x154 0x398 0x5B4 0x9 0x1
+
+#define IOMUXC_GPIO_AD_19_SAI1_RX_BCLK				0x158 0x39C 0x670 0x0 0x0
+#define IOMUXC_GPIO_AD_19_ACMP3_OUT				0x158 0x39C 0x0 0x1 0x0
+#define IOMUXC_GPIO_AD_19_LPSPI1_PCS2				0x158 0x39C 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_19_FLEXSPI1_A_SCLK			0x158 0x39C 0x574 0x3 0x0
+#define IOMUXC_GPIO_AD_19_VIDEO_MUX_CSI_DATA06			0x158 0x39C 0x0 0x4 0x0
+#define IOMUXC_GPIO_AD_19_GPIO_MUX3_IO18			0x158 0x39C 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_19_ENET_COL				0x158 0x39C 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_19_FLEXIO2_D19				0x158 0x39C 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_19_LPI2C2_SDA				0x158 0x39C 0x5B8 0x9 0x1
+#define IOMUXC_GPIO_AD_19_GPIO9_IO18				0x158 0x39C 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_19_FLEXPWM4_PWM1_X			0x158 0x39C 0x0 0xB 0x0
+
+#define IOMUXC_GPIO_AD_20_SAI1_RX_DATA00			0x15C 0x3A0 0x674 0x0 0x0
+#define IOMUXC_GPIO_AD_20_ACMP4_OUT				0x15C 0x3A0 0x0 0x1 0x0
+#define IOMUXC_GPIO_AD_20_LPSPI1_PCS3				0x15C 0x3A0 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_20_FLEXSPI1_A_DATA00			0x15C 0x3A0 0x554 0x3 0x0
+#define IOMUXC_GPIO_AD_20_VIDEO_MUX_CSI_DATA05			0x15C 0x3A0 0x0 0x4 0x0
+#define IOMUXC_GPIO_AD_20_GPIO_MUX3_IO19			0x15C 0x3A0 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_20_KPP_ROW07				0x15C 0x3A0 0x5A8 0x6 0x0
+#define IOMUXC_GPIO_AD_20_FLEXIO2_D20				0x15C 0x3A0 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_20_ENET_QOS_1588_EVENT2_OUT		0x15C 0x3A0 0x0 0x9 0x0
+#define IOMUXC_GPIO_AD_20_GPIO9_IO19				0x15C 0x3A0 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_20_FLEXPWM4_PWM2_X			0x15C 0x3A0 0x0 0xB 0x0
+
+#define IOMUXC_GPIO_AD_21_SAI1_TX_DATA00			0x160 0x3A4 0x0 0x0 0x0
+#define IOMUXC_GPIO_AD_21_LPSPI2_PCS1				0x160 0x3A4 0x5E0 0x2 0x0
+#define IOMUXC_GPIO_AD_21_FLEXSPI1_A_DATA01			0x160 0x3A4 0x558 0x3 0x0
+#define IOMUXC_GPIO_AD_21_VIDEO_MUX_CSI_DATA04			0x160 0x3A4 0x0 0x4 0x0
+#define IOMUXC_GPIO_AD_21_GPIO_MUX3_IO20			0x160 0x3A4 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_21_KPP_COL07				0x160 0x3A4 0x5A0 0x6 0x0
+#define IOMUXC_GPIO_AD_21_FLEXIO2_D21				0x160 0x3A4 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_21_ENET_QOS_1588_EVENT2_IN		0x160 0x3A4 0x0 0x9 0x0
+#define IOMUXC_GPIO_AD_21_GPIO9_IO20				0x160 0x3A4 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_21_FLEXPWM4_PWM3_X			0x160 0x3A4 0x0 0xB 0x0
+
+#define IOMUXC_GPIO_AD_22_GPIO9_IO21				0x164 0x3A8 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_22_SAI1_TX_BCLK				0x164 0x3A8 0x67C 0x0 0x0
+#define IOMUXC_GPIO_AD_22_LPSPI2_PCS2				0x164 0x3A8 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_22_FLEXSPI1_A_DATA02			0x164 0x3A8 0x55C 0x3 0x0
+#define IOMUXC_GPIO_AD_22_VIDEO_MUX_CSI_DATA03			0x164 0x3A8 0x0 0x4 0x0
+#define IOMUXC_GPIO_AD_22_GPIO_MUX3_IO21			0x164 0x3A8 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_22_KPP_ROW06				0x164 0x3A8 0x5A4 0x6 0x0
+#define IOMUXC_GPIO_AD_22_FLEXIO2_D22				0x164 0x3A8 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_22_ENET_QOS_1588_EVENT3_OUT		0x164 0x3A8 0x0 0x9 0x0
+
+#define IOMUXC_GPIO_AD_23_SAI1_TX_SYNC				0x168 0x3AC 0x680 0x0 0x0
+#define IOMUXC_GPIO_AD_23_LPSPI2_PCS3				0x168 0x3AC 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_23_FLEXSPI1_A_DATA03			0x168 0x3AC 0x560 0x3 0x0
+#define IOMUXC_GPIO_AD_23_VIDEO_MUX_CSI_DATA02			0x168 0x3AC 0x0 0x4 0x0
+#define IOMUXC_GPIO_AD_23_GPIO_MUX3_IO22			0x168 0x3AC 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_23_KPP_COL06				0x168 0x3AC 0x59C 0x6 0x0
+#define IOMUXC_GPIO_AD_23_FLEXIO2_D23				0x168 0x3AC 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_23_ENET_QOS_1588_EVENT3_IN		0x168 0x3AC 0x0 0x9 0x0
+#define IOMUXC_GPIO_AD_23_GPIO9_IO22				0x168 0x3AC 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_AD_24_LPUART1_TXD				0x16C 0x3B0 0x620 0x0 0x0
+#define IOMUXC_GPIO_AD_24_LPSPI2_SCK				0x16C 0x3B0 0x5E4 0x1 0x0
+#define IOMUXC_GPIO_AD_24_VIDEO_MUX_CSI_DATA00			0x16C 0x3B0 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_24_ENET_RX_EN				0x16C 0x3B0 0x4B8 0x3 0x0
+#define IOMUXC_GPIO_AD_24_FLEXPWM2_PWM0_A			0x16C 0x3B0 0x518 0x4 0x1
+#define IOMUXC_GPIO_AD_24_GPIO_MUX3_IO23			0x16C 0x3B0 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_24_KPP_ROW05				0x16C 0x3B0 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_24_FLEXIO2_D24				0x16C 0x3B0 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_24_LPI2C4_SCL				0x16C 0x3B0 0x5C4 0x9 0x0
+#define IOMUXC_GPIO_AD_24_GPIO9_IO23				0x16C 0x3B0 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_AD_25_GPIO9_IO24				0x170 0x3B4 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_25_LPUART1_RXD				0x170 0x3B4 0x61C 0x0 0x0
+#define IOMUXC_GPIO_AD_25_LPSPI2_PCS0				0x170 0x3B4 0x5DC 0x1 0x0
+#define IOMUXC_GPIO_AD_25_VIDEO_MUX_CSI_DATA01			0x170 0x3B4 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_25_ENET_RX_ER				0x170 0x3B4 0x4BC 0x3 0x0
+#define IOMUXC_GPIO_AD_25_FLEXPWM2_PWM0_B			0x170 0x3B4 0x524 0x4 0x1
+#define IOMUXC_GPIO_AD_25_GPIO_MUX3_IO24			0x170 0x3B4 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_25_KPP_COL05				0x170 0x3B4 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_25_FLEXIO2_D25				0x170 0x3B4 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_25_LPI2C4_SDA				0x170 0x3B4 0x5C8 0x9 0x0
+
+#define IOMUXC_GPIO_AD_26_LPUART1_CTS_B				0x174 0x3B8 0x0 0x0 0x0
+#define IOMUXC_GPIO_AD_26_LPSPI2_SOUT				0x174 0x3B8 0x5EC 0x1 0x0
+#define IOMUXC_GPIO_AD_26_SEMC_CSX01				0x174 0x3B8 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_26_ENET_RX_DATA00			0x174 0x3B8 0x4B0 0x3 0x0
+#define IOMUXC_GPIO_AD_26_FLEXPWM2_PWM1_A			0x174 0x3B8 0x51C 0x4 0x1
+#define IOMUXC_GPIO_AD_26_GPIO_MUX3_IO25			0x174 0x3B8 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_26_KPP_ROW04				0x174 0x3B8 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_26_FLEXIO2_D26				0x174 0x3B8 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_26_ENET_QOS_MDC				0x174 0x3B8 0x0 0x9 0x0
+#define IOMUXC_GPIO_AD_26_GPIO9_IO25				0x174 0x3B8 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_26_USDHC2_CD_B				0x174 0x3B8 0x6D0 0xB 0x1
+
+#define IOMUXC_GPIO_AD_27_LPUART1_RTS_B				0x178 0x3BC 0x0 0x0 0x0
+#define IOMUXC_GPIO_AD_27_LPSPI2_SIN				0x178 0x3BC 0x5E8 0x1 0x0
+#define IOMUXC_GPIO_AD_27_SEMC_CSX02				0x178 0x3BC 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_27_ENET_RX_DATA01			0x178 0x3BC 0x4B4 0x3 0x0
+#define IOMUXC_GPIO_AD_27_FLEXPWM2_PWM1_B			0x178 0x3BC 0x528 0x4 0x1
+#define IOMUXC_GPIO_AD_27_GPIO_MUX3_IO26			0x178 0x3BC 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_27_KPP_COL04				0x178 0x3BC 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_27_FLEXIO2_D27				0x178 0x3BC 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_27_ENET_QOS_MDIO				0x178 0x3BC 0x4EC 0x9 0x1
+#define IOMUXC_GPIO_AD_27_GPIO9_IO26				0x178 0x3BC 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_27_USDHC2_WP				0x178 0x3BC 0x6D4 0xB 0x1
+
+#define IOMUXC_GPIO_AD_28_GPIO9_IO27				0x17C 0x3C0 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_28_USDHC2_VSELECT			0x17C 0x3C0 0x0 0xB 0x0
+#define IOMUXC_GPIO_AD_28_LPSPI1_SCK				0x17C 0x3C0 0x5D0 0x0 0x1
+#define IOMUXC_GPIO_AD_28_LPUART5_TXD				0x17C 0x3C0 0x0 0x1 0x0
+#define IOMUXC_GPIO_AD_28_SEMC_CSX03				0x17C 0x3C0 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_28_ENET_TX_EN				0x17C 0x3C0 0x0 0x3 0x0
+#define IOMUXC_GPIO_AD_28_FLEXPWM2_PWM2_A			0x17C 0x3C0 0x520 0x4 0x1
+#define IOMUXC_GPIO_AD_28_GPIO_MUX3_IO27			0x17C 0x3C0 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_28_KPP_ROW03				0x17C 0x3C0 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_28_FLEXIO2_D28				0x17C 0x3C0 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_28_VIDEO_MUX_EXT_DCIC1			0x17C 0x3C0 0x0 0x9 0x0
+
+#define IOMUXC_GPIO_AD_29_LPSPI1_PCS0				0x180 0x3C4 0x5CC 0x0 0x1
+#define IOMUXC_GPIO_AD_29_LPUART5_RXD				0x180 0x3C4 0x0 0x1 0x0
+#define IOMUXC_GPIO_AD_29_ENET_REF_CLK				0x180 0x3C4 0x4A8 0x2 0x0
+#define IOMUXC_GPIO_AD_29_ENET_TX_CLK				0x180 0x3C4 0x4C0 0x3 0x0
+#define IOMUXC_GPIO_AD_29_FLEXPWM2_PWM2_B			0x180 0x3C4 0x52C 0x4 0x1
+#define IOMUXC_GPIO_AD_29_GPIO_MUX3_IO28			0x180 0x3C4 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_29_KPP_COL03				0x180 0x3C4 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_29_FLEXIO2_D29				0x180 0x3C4 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_29_VIDEO_MUX_EXT_DCIC2			0x180 0x3C4 0x0 0x9 0x0
+#define IOMUXC_GPIO_AD_29_GPIO9_IO28				0x180 0x3C4 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_29_USDHC2_RESET_B			0x180 0x3C4 0x0 0xB 0x0
+
+#define IOMUXC_GPIO_AD_30_LPSPI1_SOUT				0x184 0x3C8 0x5D8 0x0 0x1
+#define IOMUXC_GPIO_AD_30_USB_OTG2_OC				0x184 0x3C8 0x6B8 0x1 0x1
+#define IOMUXC_GPIO_AD_30_FLEXCAN2_TX				0x184 0x3C8 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_30_ENET_TX_DATA00			0x184 0x3C8 0x0 0x3 0x0
+#define IOMUXC_GPIO_AD_30_LPUART3_TXD				0x184 0x3C8 0x0 0x4 0x0
+#define IOMUXC_GPIO_AD_30_GPIO_MUX3_IO29			0x184 0x3C8 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_30_KPP_ROW02				0x184 0x3C8 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_30_FLEXIO2_D30				0x184 0x3C8 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_30_WDOG2_RESET_B_DEB			0x184 0x3C8 0x0 0x9 0x0
+#define IOMUXC_GPIO_AD_30_GPIO9_IO29				0x184 0x3C8 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_AD_31_LPSPI1_SIN				0x188 0x3CC 0x5D4 0x0 0x1
+#define IOMUXC_GPIO_AD_31_USB_OTG2_PWR				0x188 0x3CC 0x0 0x1 0x0
+#define IOMUXC_GPIO_AD_31_FLEXCAN2_RX				0x188 0x3CC 0x49C 0x2 0x1
+#define IOMUXC_GPIO_AD_31_ENET_TX_DATA01			0x188 0x3CC 0x0 0x3 0x0
+#define IOMUXC_GPIO_AD_31_LPUART3_RXD				0x188 0x3CC 0x0 0x4 0x0
+#define IOMUXC_GPIO_AD_31_GPIO_MUX3_IO30			0x188 0x3CC 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_31_KPP_COL02				0x188 0x3CC 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_31_FLEXIO2_D31				0x188 0x3CC 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_31_WDOG1_RESET_B_DEB			0x188 0x3CC 0x0 0x9 0x0
+#define IOMUXC_GPIO_AD_31_GPIO9_IO30				0x188 0x3CC 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_AD_32_GPIO9_IO31				0x18C 0x3D0 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_32_LPI2C1_SCL				0x18C 0x3D0 0x5AC 0x0 0x1
+#define IOMUXC_GPIO_AD_32_USBPHY2_OTG_ID			0x18C 0x3D0 0x6C4 0x1 0x1
+#define IOMUXC_GPIO_AD_32_PGMC_PMIC_RDY				0x18C 0x3D0 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_32_ENET_MDC				0x18C 0x3D0 0x0 0x3 0x0
+#define IOMUXC_GPIO_AD_32_USDHC1_CD_B				0x18C 0x3D0 0x6C8 0x4 0x0
+#define IOMUXC_GPIO_AD_32_GPIO_MUX3_IO31			0x18C 0x3D0 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_32_KPP_ROW01				0x18C 0x3D0 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_32_LPUART10_TXD				0x18C 0x3D0 0x628 0x8 0x1
+#define IOMUXC_GPIO_AD_32_ENET_1G_MDC				0x18C 0x3D0 0x0 0x9 0x0
+
+#define IOMUXC_GPIO_AD_33_LPI2C1_SDA				0x190 0x3D4 0x5B0 0x0 0x1
+#define IOMUXC_GPIO_AD_33_USBPHY1_OTG_ID			0x190 0x3D4 0x6C0 0x1 0x1
+#define IOMUXC_GPIO_AD_33_XBAR1_INOUT17				0x190 0x3D4 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_33_ENET_MDIO				0x190 0x3D4 0x4AC 0x3 0x1
+#define IOMUXC_GPIO_AD_33_USDHC1_WP				0x190 0x3D4 0x6CC 0x4 0x0
+#define IOMUXC_GPIO_AD_33_GPIO_MUX4_IO00			0x190 0x3D4 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_33_KPP_COL01				0x190 0x3D4 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_33_LPUART10_RXD				0x190 0x3D4 0x624 0x8 0x1
+#define IOMUXC_GPIO_AD_33_ENET_1G_MDIO				0x190 0x3D4 0x4C8 0x9 0x3
+#define IOMUXC_GPIO_AD_33_GPIO10_IO00				0x190 0x3D4 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_AD_34_ENET_1G_1588_EVENT0_IN		0x194 0x3D8 0x0 0x0 0x0
+#define IOMUXC_GPIO_AD_34_USB_OTG1_PWR				0x194 0x3D8 0x0 0x1 0x0
+#define IOMUXC_GPIO_AD_34_XBAR1_INOUT18				0x194 0x3D8 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_34_ENET_1588_EVENT0_IN			0x194 0x3D8 0x0 0x3 0x0
+#define IOMUXC_GPIO_AD_34_USDHC1_VSELECT			0x194 0x3D8 0x0 0x4 0x0
+#define IOMUXC_GPIO_AD_34_GPIO_MUX4_IO01			0x194 0x3D8 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_34_KPP_ROW00				0x194 0x3D8 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_34_LPUART10_CTS_B			0x194 0x3D8 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_34_WDOG1_ANY				0x194 0x3D8 0x0 0x9 0x0
+#define IOMUXC_GPIO_AD_34_GPIO10_IO01				0x194 0x3D8 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_AD_35_GPIO10_IO02				0x198 0x3DC 0x0 0xA 0x0
+#define IOMUXC_GPIO_AD_35_ENET_1G_1588_EVENT0_OUT		0x198 0x3DC 0x0 0x0 0x0
+#define IOMUXC_GPIO_AD_35_USB_OTG1_OC				0x198 0x3DC 0x6BC 0x1 0x1
+#define IOMUXC_GPIO_AD_35_XBAR1_INOUT19				0x198 0x3DC 0x0 0x2 0x0
+#define IOMUXC_GPIO_AD_35_ENET_1588_EVENT0_OUT			0x198 0x3DC 0x0 0x3 0x0
+#define IOMUXC_GPIO_AD_35_USDHC1_RESET_B			0x198 0x3DC 0x0 0x4 0x0
+#define IOMUXC_GPIO_AD_35_GPIO_MUX4_IO02			0x198 0x3DC 0x0 0x5 0x0
+#define IOMUXC_GPIO_AD_35_KPP_COL00				0x198 0x3DC 0x0 0x6 0x0
+#define IOMUXC_GPIO_AD_35_LPUART10_RTS_B			0x198 0x3DC 0x0 0x8 0x0
+#define IOMUXC_GPIO_AD_35_FLEXSPI1_B_SS1_B			0x198 0x3DC 0x0 0x9 0x0
+
+#define IOMUXC_GPIO_SD_B1_00_USDHC1_CMD				0x19C 0x3E0 0x0 0x0 0x0
+#define IOMUXC_GPIO_SD_B1_00_XBAR1_INOUT20			0x19C 0x3E0 0x6D8 0x2 0x1
+#define IOMUXC_GPIO_SD_B1_00_GPT4_CAPTURE1			0x19C 0x3E0 0x0 0x3 0x0
+#define IOMUXC_GPIO_SD_B1_00_GPIO_MUX4_IO03			0x19C 0x3E0 0x0 0x5 0x0
+#define IOMUXC_GPIO_SD_B1_00_FLEXSPI2_A_SS0_B			0x19C 0x3E0 0x0 0x6 0x0
+#define IOMUXC_GPIO_SD_B1_00_KPP_ROW07				0x19C 0x3E0 0x5A8 0x8 0x1
+#define IOMUXC_GPIO_SD_B1_00_GPIO10_IO03			0x19C 0x3E0 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_SD_B1_01_USDHC1_CLK				0x1A0 0x3E4 0x0 0x0 0x0
+#define IOMUXC_GPIO_SD_B1_01_XBAR1_INOUT21			0x1A0 0x3E4 0x6DC 0x2 0x1
+#define IOMUXC_GPIO_SD_B1_01_GPT4_CAPTURE2			0x1A0 0x3E4 0x0 0x3 0x0
+#define IOMUXC_GPIO_SD_B1_01_GPIO_MUX4_IO04			0x1A0 0x3E4 0x0 0x5 0x0
+#define IOMUXC_GPIO_SD_B1_01_FLEXSPI2_A_SCLK			0x1A0 0x3E4 0x58C 0x6 0x1
+#define IOMUXC_GPIO_SD_B1_01_KPP_COL07				0x1A0 0x3E4 0x5A0 0x8 0x1
+#define IOMUXC_GPIO_SD_B1_01_GPIO10_IO04			0x1A0 0x3E4 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_SD_B1_02_GPIO10_IO05			0x1A4 0x3E8 0x0 0xA 0x0
+#define IOMUXC_GPIO_SD_B1_02_USDHC1_DATA0			0x1A4 0x3E8 0x0 0x0 0x0
+#define IOMUXC_GPIO_SD_B1_02_XBAR1_INOUT22			0x1A4 0x3E8 0x6E0 0x2 0x1
+#define IOMUXC_GPIO_SD_B1_02_GPT4_COMPARE1			0x1A4 0x3E8 0x0 0x3 0x0
+#define IOMUXC_GPIO_SD_B1_02_GPIO_MUX4_IO05			0x1A4 0x3E8 0x0 0x5 0x0
+#define IOMUXC_GPIO_SD_B1_02_FLEXSPI2_A_DATA00			0x1A4 0x3E8 0x57C 0x6 0x1
+#define IOMUXC_GPIO_SD_B1_02_KPP_ROW06				0x1A4 0x3E8 0x5A4 0x8 0x1
+#define IOMUXC_GPIO_SD_B1_02_FLEXSPI1_A_SS1_B			0x1A4 0x3E8 0x0 0x9 0x0
+
+#define IOMUXC_GPIO_SD_B1_03_USDHC1_DATA1			0x1A8 0x3EC 0x0 0x0 0x0
+#define IOMUXC_GPIO_SD_B1_03_XBAR1_INOUT23			0x1A8 0x3EC 0x6E4 0x2 0x1
+#define IOMUXC_GPIO_SD_B1_03_GPT4_COMPARE2			0x1A8 0x3EC 0x0 0x3 0x0
+#define IOMUXC_GPIO_SD_B1_03_GPIO_MUX4_IO06			0x1A8 0x3EC 0x0 0x5 0x0
+#define IOMUXC_GPIO_SD_B1_03_FLEXSPI2_A_DATA01			0x1A8 0x3EC 0x580 0x6 0x1
+#define IOMUXC_GPIO_SD_B1_03_KPP_COL06				0x1A8 0x3EC 0x59C 0x8 0x1
+#define IOMUXC_GPIO_SD_B1_03_FLEXSPI1_B_SS1_B			0x1A8 0x3EC 0x0 0x9 0x0
+#define IOMUXC_GPIO_SD_B1_03_GPIO10_IO06			0x1A8 0x3EC 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_SD_B1_04_USDHC1_DATA2			0x1AC 0x3F0 0x0 0x0 0x0
+#define IOMUXC_GPIO_SD_B1_04_XBAR1_INOUT24			0x1AC 0x3F0 0x6E8 0x2 0x1
+#define IOMUXC_GPIO_SD_B1_04_GPT4_COMPARE3			0x1AC 0x3F0 0x0 0x3 0x0
+#define IOMUXC_GPIO_SD_B1_04_GPIO_MUX4_IO07			0x1AC 0x3F0 0x0 0x5 0x0
+#define IOMUXC_GPIO_SD_B1_04_FLEXSPI2_A_DATA02			0x1AC 0x3F0 0x584 0x6 0x1
+#define IOMUXC_GPIO_SD_B1_04_FLEXSPI1_B_SS0_B			0x1AC 0x3F0 0x0 0x8 0x0
+#define IOMUXC_GPIO_SD_B1_04_ENET_QOS_1588_EVENT2_AUX_IN	0x1AC 0x3F0 0x0 0x9 0x0
+#define IOMUXC_GPIO_SD_B1_04_GPIO10_IO07			0x1AC 0x3F0 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_SD_B1_05_GPIO10_IO08			0x1B0 0x3F4 0x0 0xA 0x0
+#define IOMUXC_GPIO_SD_B1_05_USDHC1_DATA3			0x1B0 0x3F4 0x0 0x0 0x0
+#define IOMUXC_GPIO_SD_B1_05_XBAR1_INOUT25			0x1B0 0x3F4 0x6EC 0x2 0x1
+#define IOMUXC_GPIO_SD_B1_05_GPT4_CLK				0x1B0 0x3F4 0x0 0x3 0x0
+#define IOMUXC_GPIO_SD_B1_05_GPIO_MUX4_IO08			0x1B0 0x3F4 0x0 0x5 0x0
+#define IOMUXC_GPIO_SD_B1_05_FLEXSPI2_A_DATA03			0x1B0 0x3F4 0x588 0x6 0x1
+#define IOMUXC_GPIO_SD_B1_05_FLEXSPI1_B_DQS			0x1B0 0x3F4 0x0 0x8 0x0
+#define IOMUXC_GPIO_SD_B1_05_ENET_QOS_1588_EVENT3_AUX_IN	0x1B0 0x3F4 0x0 0x9 0x0
+
+#define IOMUXC_GPIO_SD_B2_00_GPIO10_IO09			0x1B4 0x3F8 0x0 0xA 0x0
+#define IOMUXC_GPIO_SD_B2_00_USDHC2_DATA3			0x1B4 0x3F8 0x0 0x0 0x0
+#define IOMUXC_GPIO_SD_B2_00_FLEXSPI1_B_DATA03			0x1B4 0x3F8 0x570 0x1 0x1
+#define IOMUXC_GPIO_SD_B2_00_ENET_1G_RX_EN			0x1B4 0x3F8 0x4E0 0x2 0x1
+#define IOMUXC_GPIO_SD_B2_00_LPUART9_TXD			0x1B4 0x3F8 0x0 0x3 0x0
+#define IOMUXC_GPIO_SD_B2_00_LPSPI4_SCK				0x1B4 0x3F8 0x610 0x4 0x0
+#define IOMUXC_GPIO_SD_B2_00_GPIO_MUX4_IO09			0x1B4 0x3F8 0x0 0x5 0x0
+
+#define IOMUXC_GPIO_SD_B2_01_USDHC2_DATA2			0x1B8 0x3FC 0x0 0x0 0x0
+#define IOMUXC_GPIO_SD_B2_01_FLEXSPI1_B_DATA02			0x1B8 0x3FC 0x56C 0x1 0x1
+#define IOMUXC_GPIO_SD_B2_01_ENET_1G_RX_CLK			0x1B8 0x3FC 0x4CC 0x2 0x1
+#define IOMUXC_GPIO_SD_B2_01_LPUART9_RXD			0x1B8 0x3FC 0x0 0x3 0x0
+#define IOMUXC_GPIO_SD_B2_01_LPSPI4_PCS0			0x1B8 0x3FC 0x60C 0x4 0x0
+#define IOMUXC_GPIO_SD_B2_01_GPIO_MUX4_IO10			0x1B8 0x3FC 0x0 0x5 0x0
+#define IOMUXC_GPIO_SD_B2_01_GPIO10_IO10			0x1B8 0x3FC 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_SD_B2_02_GPIO10_IO11			0x1BC 0x400 0x0 0xA 0x0
+#define IOMUXC_GPIO_SD_B2_02_USDHC2_DATA1			0x1BC 0x400 0x0 0x0 0x0
+#define IOMUXC_GPIO_SD_B2_02_FLEXSPI1_B_DATA01			0x1BC 0x400 0x568 0x1 0x1
+#define IOMUXC_GPIO_SD_B2_02_ENET_1G_RX_DATA00			0x1BC 0x400 0x4D0 0x2 0x1
+#define IOMUXC_GPIO_SD_B2_02_LPUART9_CTS_B			0x1BC 0x400 0x0 0x3 0x0
+#define IOMUXC_GPIO_SD_B2_02_LPSPI4_SOUT			0x1BC 0x400 0x618 0x4 0x0
+#define IOMUXC_GPIO_SD_B2_02_GPIO_MUX4_IO11			0x1BC 0x400 0x0 0x5 0x0
+
+#define IOMUXC_GPIO_SD_B2_03_GPIO10_IO12			0x1C0 0x404 0x0 0xA 0x0
+#define IOMUXC_GPIO_SD_B2_03_USDHC2_DATA0			0x1C0 0x404 0x0 0x0 0x0
+#define IOMUXC_GPIO_SD_B2_03_FLEXSPI1_B_DATA00			0x1C0 0x404 0x564 0x1 0x1
+#define IOMUXC_GPIO_SD_B2_03_ENET_1G_RX_DATA01			0x1C0 0x404 0x4D4 0x2 0x1
+#define IOMUXC_GPIO_SD_B2_03_LPUART9_RTS_B			0x1C0 0x404 0x0 0x3 0x0
+#define IOMUXC_GPIO_SD_B2_03_LPSPI4_SIN				0x1C0 0x404 0x614 0x4 0x0
+#define IOMUXC_GPIO_SD_B2_03_GPIO_MUX4_IO12			0x1C0 0x404 0x0 0x5 0x0
+
+#define IOMUXC_GPIO_SD_B2_04_USDHC2_CLK				0x1C4 0x408 0x0 0x0 0x0
+#define IOMUXC_GPIO_SD_B2_04_FLEXSPI1_B_SCLK			0x1C4 0x408 0x578 0x1 0x1
+#define IOMUXC_GPIO_SD_B2_04_ENET_1G_RX_DATA02			0x1C4 0x408 0x4D8 0x2 0x1
+#define IOMUXC_GPIO_SD_B2_04_FLEXSPI1_A_SS1_B			0x1C4 0x408 0x0 0x3 0x0
+#define IOMUXC_GPIO_SD_B2_04_LPSPI4_PCS1			0x1C4 0x408 0x0 0x4 0x0
+#define IOMUXC_GPIO_SD_B2_04_GPIO_MUX4_IO13			0x1C4 0x408 0x0 0x5 0x0
+#define IOMUXC_GPIO_SD_B2_04_GPIO10_IO13			0x1C4 0x408 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_SD_B2_05_GPIO10_IO14			0x1C8 0x40C 0x0 0xA 0x0
+#define IOMUXC_GPIO_SD_B2_05_USDHC2_CMD				0x1C8 0x40C 0x0 0x0 0x0
+#define IOMUXC_GPIO_SD_B2_05_FLEXSPI1_A_DQS			0x1C8 0x40C 0x550 0x1 0x2
+#define IOMUXC_GPIO_SD_B2_05_ENET_1G_RX_DATA03			0x1C8 0x40C 0x4DC 0x2 0x1
+#define IOMUXC_GPIO_SD_B2_05_FLEXSPI1_B_SS0_B			0x1C8 0x40C 0x0 0x3 0x0
+#define IOMUXC_GPIO_SD_B2_05_LPSPI4_PCS2			0x1C8 0x40C 0x0 0x4 0x0
+#define IOMUXC_GPIO_SD_B2_05_GPIO_MUX4_IO14			0x1C8 0x40C 0x0 0x5 0x0
+
+#define IOMUXC_GPIO_SD_B2_06_GPIO10_IO15			0x1CC 0x410 0x0 0xA 0x0
+#define IOMUXC_GPIO_SD_B2_06_USDHC2_RESET_B			0x1CC 0x410 0x0 0x0 0x0
+#define IOMUXC_GPIO_SD_B2_06_FLEXSPI1_A_SS0_B			0x1CC 0x410 0x0 0x1 0x0
+#define IOMUXC_GPIO_SD_B2_06_ENET_1G_TX_DATA03			0x1CC 0x410 0x0 0x2 0x0
+#define IOMUXC_GPIO_SD_B2_06_LPSPI4_PCS3			0x1CC 0x410 0x0 0x3 0x0
+#define IOMUXC_GPIO_SD_B2_06_GPT6_CAPTURE1			0x1CC 0x410 0x0 0x4 0x0
+#define IOMUXC_GPIO_SD_B2_06_GPIO_MUX4_IO15			0x1CC 0x410 0x0 0x5 0x0
+
+#define IOMUXC_GPIO_SD_B2_07_USDHC2_STROBE			0x1D0 0x414 0x0 0x0 0x0
+#define IOMUXC_GPIO_SD_B2_07_FLEXSPI1_A_SCLK			0x1D0 0x414 0x574 0x1 0x1
+#define IOMUXC_GPIO_SD_B2_07_ENET_1G_TX_DATA02			0x1D0 0x414 0x0 0x2 0x0
+#define IOMUXC_GPIO_SD_B2_07_LPUART3_CTS_B			0x1D0 0x414 0x0 0x3 0x0
+#define IOMUXC_GPIO_SD_B2_07_GPT6_CAPTURE2			0x1D0 0x414 0x0 0x4 0x0
+#define IOMUXC_GPIO_SD_B2_07_GPIO_MUX4_IO16			0x1D0 0x414 0x0 0x5 0x0
+#define IOMUXC_GPIO_SD_B2_07_LPSPI2_SCK				0x1D0 0x414 0x5E4 0x6 0x1
+#define IOMUXC_GPIO_SD_B2_07_ENET_TX_ER				0x1D0 0x414 0x0 0x8 0x0
+#define IOMUXC_GPIO_SD_B2_07_ENET_QOS_REF_CLK			0x1D0 0x414 0x4A0 0x9 0x1
+#define IOMUXC_GPIO_SD_B2_07_GPIO10_IO16			0x1D0 0x414 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_SD_B2_08_GPIO10_IO17			0x1D4 0x418 0x0 0xA 0x0
+#define IOMUXC_GPIO_SD_B2_08_USDHC2_DATA4			0x1D4 0x418 0x0 0x0 0x0
+#define IOMUXC_GPIO_SD_B2_08_FLEXSPI1_A_DATA00			0x1D4 0x418 0x554 0x1 0x1
+#define IOMUXC_GPIO_SD_B2_08_ENET_1G_TX_DATA01			0x1D4 0x418 0x0 0x2 0x0
+#define IOMUXC_GPIO_SD_B2_08_LPUART3_RTS_B			0x1D4 0x418 0x0 0x3 0x0
+#define IOMUXC_GPIO_SD_B2_08_GPT6_COMPARE1			0x1D4 0x418 0x0 0x4 0x0
+#define IOMUXC_GPIO_SD_B2_08_GPIO_MUX4_IO17			0x1D4 0x418 0x0 0x5 0x0
+#define IOMUXC_GPIO_SD_B2_08_LPSPI2_PCS0			0x1D4 0x418 0x5DC 0x6 0x1
+
+#define IOMUXC_GPIO_SD_B2_09_GPIO10_IO18			0x1D8 0x41C 0x0 0xA 0x0
+#define IOMUXC_GPIO_SD_B2_09_USDHC2_DATA5			0x1D8 0x41C 0x0 0x0 0x0
+#define IOMUXC_GPIO_SD_B2_09_FLEXSPI1_A_DATA01			0x1D8 0x41C 0x558 0x1 0x1
+#define IOMUXC_GPIO_SD_B2_09_ENET_1G_TX_DATA00			0x1D8 0x41C 0x0 0x2 0x0
+#define IOMUXC_GPIO_SD_B2_09_LPUART5_CTS_B			0x1D8 0x41C 0x0 0x3 0x0
+#define IOMUXC_GPIO_SD_B2_09_GPT6_COMPARE2			0x1D8 0x41C 0x0 0x4 0x0
+#define IOMUXC_GPIO_SD_B2_09_GPIO_MUX4_IO18			0x1D8 0x41C 0x0 0x5 0x0
+#define IOMUXC_GPIO_SD_B2_09_LPSPI2_SOUT			0x1D8 0x41C 0x5EC 0x6 0x1
+
+#define IOMUXC_GPIO_SD_B2_10_GPIO10_IO19			0x1DC 0x420 0x0 0xA 0x0
+#define IOMUXC_GPIO_SD_B2_10_USDHC2_DATA6			0x1DC 0x420 0x0 0x0 0x0
+#define IOMUXC_GPIO_SD_B2_10_FLEXSPI1_A_DATA02			0x1DC 0x420 0x55C 0x1 0x1
+#define IOMUXC_GPIO_SD_B2_10_ENET_1G_TX_EN			0x1DC 0x420 0x0 0x2 0x0
+#define IOMUXC_GPIO_SD_B2_10_LPUART5_RTS_B			0x1DC 0x420 0x0 0x3 0x0
+#define IOMUXC_GPIO_SD_B2_10_GPT6_COMPARE3			0x1DC 0x420 0x0 0x4 0x0
+#define IOMUXC_GPIO_SD_B2_10_GPIO_MUX4_IO19			0x1DC 0x420 0x0 0x5 0x0
+#define IOMUXC_GPIO_SD_B2_10_LPSPI2_SIN				0x1DC 0x420 0x5E8 0x6 0x1
+
+#define IOMUXC_GPIO_SD_B2_11_USDHC2_DATA7			0x1E0 0x424 0x0 0x0 0x0
+#define IOMUXC_GPIO_SD_B2_11_FLEXSPI1_A_DATA03			0x1E0 0x424 0x560 0x1 0x1
+#define IOMUXC_GPIO_SD_B2_11_ENET_1G_TX_CLK_IO			0x1E0 0x424 0x4E8 0x2 0x1
+#define IOMUXC_GPIO_SD_B2_11_ENET_1G_REF_CLK			0x1E0 0x424 0x4C4 0x3 0x1
+#define IOMUXC_GPIO_SD_B2_11_GPT6_CLK				0x1E0 0x424 0x0 0x4 0x0
+#define IOMUXC_GPIO_SD_B2_11_GPIO_MUX4_IO20			0x1E0 0x424 0x0 0x5 0x0
+#define IOMUXC_GPIO_SD_B2_11_LPSPI2_PCS1			0x1E0 0x424 0x5E0 0x6 0x1
+#define IOMUXC_GPIO_SD_B2_11_GPIO10_IO20			0x1E0 0x424 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_DISP_B1_00_VIDEO_MUX_LCDIF_CLK		0x1E4 0x428 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B1_00_ENET_1G_RX_EN			0x1E4 0x428 0x4E0 0x1 0x2
+#define IOMUXC_GPIO_DISP_B1_00_TMR1_TIMER0			0x1E4 0x428 0x63C 0x3 0x2
+#define IOMUXC_GPIO_DISP_B1_00_XBAR1_INOUT26			0x1E4 0x428 0x6F0 0x4 0x1
+#define IOMUXC_GPIO_DISP_B1_00_GPIO_MUX4_IO21			0x1E4 0x428 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B1_00_ENET_QOS_RX_EN			0x1E4 0x428 0x4F8 0x8 0x0
+#define IOMUXC_GPIO_DISP_B1_00_GPIO10_IO21			0x1E4 0x428 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_DISP_B1_01_VIDEO_MUX_LCDIF_ENABLE		0x1E8 0x42C 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B1_01_ENET_1G_RX_CLK			0x1E8 0x42C 0x4CC 0x1 0x2
+#define IOMUXC_GPIO_DISP_B1_01_ENET_1G_RX_ER			0x1E8 0x42C 0x4E4 0x2 0x1
+#define IOMUXC_GPIO_DISP_B1_01_TMR1_TIMER1			0x1E8 0x42C 0x640 0x3 0x2
+#define IOMUXC_GPIO_DISP_B1_01_XBAR1_INOUT27			0x1E8 0x42C 0x6F4 0x4 0x1
+#define IOMUXC_GPIO_DISP_B1_01_GPIO_MUX4_IO22			0x1E8 0x42C 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B1_01_ENET_QOS_RX_CLK			0x1E8 0x42C 0x0 0x8 0x0
+#define IOMUXC_GPIO_DISP_B1_01_ENET_QOS_RX_ER			0x1E8 0x42C 0x4FC 0x9 0x0
+#define IOMUXC_GPIO_DISP_B1_01_GPIO10_IO22			0x1E8 0x42C 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_DISP_B1_02_GPIO10_IO23			0x1EC 0x430 0x0 0xA 0x0
+#define IOMUXC_GPIO_DISP_B1_02_VIDEO_MUX_LCDIF_HSYNC		0x1EC 0x430 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B1_02_ENET_1G_RX_DATA00		0x1EC 0x430 0x4D0 0x1 0x2
+#define IOMUXC_GPIO_DISP_B1_02_LPI2C3_SCL			0x1EC 0x430 0x5BC 0x2 0x0
+#define IOMUXC_GPIO_DISP_B1_02_TMR1_TIMER2			0x1EC 0x430 0x644 0x3 0x1
+#define IOMUXC_GPIO_DISP_B1_02_XBAR1_INOUT28			0x1EC 0x430 0x6F8 0x4 0x1
+#define IOMUXC_GPIO_DISP_B1_02_GPIO_MUX4_IO23			0x1EC 0x430 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B1_02_ENET_QOS_RX_DATA00		0x1EC 0x430 0x4F0 0x8 0x0
+#define IOMUXC_GPIO_DISP_B1_02_LPUART1_TXD			0x1EC 0x430 0x620 0x9 0x1
+
+#define IOMUXC_GPIO_DISP_B1_03_VIDEO_MUX_LCDIF_VSYNC		0x1F0 0x434 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B1_03_ENET_1G_RX_DATA01		0x1F0 0x434 0x4D4 0x1 0x2
+#define IOMUXC_GPIO_DISP_B1_03_LPI2C3_SDA			0x1F0 0x434 0x5C0 0x2 0x0
+#define IOMUXC_GPIO_DISP_B1_03_TMR2_TIMER0			0x1F0 0x434 0x648 0x3 0x2
+#define IOMUXC_GPIO_DISP_B1_03_XBAR1_INOUT29			0x1F0 0x434 0x6FC 0x4 0x1
+#define IOMUXC_GPIO_DISP_B1_03_GPIO_MUX4_IO24			0x1F0 0x434 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B1_03_ENET_QOS_RX_DATA01		0x1F0 0x434 0x4F4 0x8 0x0
+#define IOMUXC_GPIO_DISP_B1_03_LPUART1_RXD			0x1F0 0x434 0x61C 0x9 0x1
+#define IOMUXC_GPIO_DISP_B1_03_GPIO10_IO24			0x1F0 0x434 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_DISP_B1_04_VIDEO_MUX_LCDIF_DATA00		0x1F4 0x438 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B1_04_ENET_1G_RX_DATA02		0x1F4 0x438 0x4D8 0x1 0x2
+#define IOMUXC_GPIO_DISP_B1_04_LPUART4_RXD			0x1F4 0x438 0x0 0x2 0x0
+#define IOMUXC_GPIO_DISP_B1_04_TMR2_TIMER1			0x1F4 0x438 0x64C 0x3 0x2
+#define IOMUXC_GPIO_DISP_B1_04_XBAR1_INOUT30			0x1F4 0x438 0x700 0x4 0x1
+#define IOMUXC_GPIO_DISP_B1_04_GPIO_MUX4_IO25			0x1F4 0x438 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B1_04_ENET_QOS_RX_DATA02		0x1F4 0x438 0x0 0x8 0x0
+#define IOMUXC_GPIO_DISP_B1_04_LPSPI3_SCK			0x1F4 0x438 0x600 0x9 0x1
+#define IOMUXC_GPIO_DISP_B1_04_GPIO10_IO25			0x1F4 0x438 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_DISP_B1_05_GPIO10_IO26			0x1F8 0x43C 0x0 0xA 0x0
+#define IOMUXC_GPIO_DISP_B1_05_VIDEO_MUX_LCDIF_DATA01		0x1F8 0x43C 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B1_05_ENET_1G_RX_DATA03		0x1F8 0x43C 0x4DC 0x1 0x2
+#define IOMUXC_GPIO_DISP_B1_05_LPUART4_CTS_B			0x1F8 0x43C 0x0 0x2 0x0
+#define IOMUXC_GPIO_DISP_B1_05_TMR2_TIMER2			0x1F8 0x43C 0x650 0x3 0x1
+#define IOMUXC_GPIO_DISP_B1_05_XBAR1_INOUT31			0x1F8 0x43C 0x704 0x4 0x1
+#define IOMUXC_GPIO_DISP_B1_05_GPIO_MUX4_IO26			0x1F8 0x43C 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B1_05_ENET_QOS_RX_DATA03		0x1F8 0x43C 0x0 0x8 0x0
+#define IOMUXC_GPIO_DISP_B1_05_LPSPI3_SIN			0x1F8 0x43C 0x604 0x9 0x1
+
+#define IOMUXC_GPIO_DISP_B1_06_VIDEO_MUX_LCDIF_DATA02		0x1FC 0x440 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B1_06_ENET_1G_TX_DATA03		0x1FC 0x440 0x0 0x1 0x0
+#define IOMUXC_GPIO_DISP_B1_06_LPUART4_TXD			0x1FC 0x440 0x0 0x2 0x0
+#define IOMUXC_GPIO_DISP_B1_06_TMR3_TIMER0			0x1FC 0x440 0x654 0x3 0x2
+#define IOMUXC_GPIO_DISP_B1_06_XBAR1_INOUT32			0x1FC 0x440 0x708 0x4 0x1
+#define IOMUXC_GPIO_DISP_B1_06_GPIO_MUX4_IO27			0x1FC 0x440 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B1_06_SRC_BT_CFG00			0x1FC 0x440 0x0 0x6 0x0
+#define IOMUXC_GPIO_DISP_B1_06_ENET_QOS_TX_DATA03		0x1FC 0x440 0x0 0x8 0x0
+#define IOMUXC_GPIO_DISP_B1_06_LPSPI3_SOUT			0x1FC 0x440 0x608 0x9 0x1
+#define IOMUXC_GPIO_DISP_B1_06_GPIO10_IO27			0x1FC 0x440 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_DISP_B1_07_VIDEO_MUX_LCDIF_DATA03		0x200 0x444 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B1_07_ENET_1G_TX_DATA02		0x200 0x444 0x0 0x1 0x0
+#define IOMUXC_GPIO_DISP_B1_07_LPUART4_RTS_B			0x200 0x444 0x0 0x2 0x0
+#define IOMUXC_GPIO_DISP_B1_07_TMR3_TIMER1			0x200 0x444 0x658 0x3 0x2
+#define IOMUXC_GPIO_DISP_B1_07_XBAR1_INOUT33			0x200 0x444 0x70C 0x4 0x1
+#define IOMUXC_GPIO_DISP_B1_07_GPIO_MUX4_IO28			0x200 0x444 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B1_07_SRC_BT_CFG01			0x200 0x444 0x0 0x6 0x0
+#define IOMUXC_GPIO_DISP_B1_07_ENET_QOS_TX_DATA02		0x200 0x444 0x0 0x8 0x0
+#define IOMUXC_GPIO_DISP_B1_07_LPSPI3_PCS0			0x200 0x444 0x5F0 0x9 0x1
+#define IOMUXC_GPIO_DISP_B1_07_GPIO10_IO28			0x200 0x444 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_DISP_B1_08_GPIO10_IO29			0x204 0x448 0x0 0xA 0x0
+#define IOMUXC_GPIO_DISP_B1_08_VIDEO_MUX_LCDIF_DATA04		0x204 0x448 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B1_08_ENET_1G_TX_DATA01		0x204 0x448 0x0 0x1 0x0
+#define IOMUXC_GPIO_DISP_B1_08_USDHC1_CD_B			0x204 0x448 0x6C8 0x2 0x1
+#define IOMUXC_GPIO_DISP_B1_08_TMR3_TIMER2			0x204 0x448 0x65C 0x3 0x1
+#define IOMUXC_GPIO_DISP_B1_08_XBAR1_INOUT34			0x204 0x448 0x710 0x4 0x1
+#define IOMUXC_GPIO_DISP_B1_08_GPIO_MUX4_IO29			0x204 0x448 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B1_08_SRC_BT_CFG02			0x204 0x448 0x0 0x6 0x0
+#define IOMUXC_GPIO_DISP_B1_08_ENET_QOS_TX_DATA01		0x204 0x448 0x0 0x8 0x0
+#define IOMUXC_GPIO_DISP_B1_08_LPSPI3_PCS1			0x204 0x448 0x5F4 0x9 0x1
+
+#define IOMUXC_GPIO_DISP_B1_09_VIDEO_MUX_LCDIF_DATA05		0x208 0x44C 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B1_09_ENET_1G_TX_DATA00		0x208 0x44C 0x0 0x1 0x0
+#define IOMUXC_GPIO_DISP_B1_09_USDHC1_WP			0x208 0x44C 0x6CC 0x2 0x1
+#define IOMUXC_GPIO_DISP_B1_09_TMR4_TIMER0			0x208 0x44C 0x660 0x3 0x2
+#define IOMUXC_GPIO_DISP_B1_09_XBAR1_INOUT35			0x208 0x44C 0x714 0x4 0x1
+#define IOMUXC_GPIO_DISP_B1_09_GPIO_MUX4_IO30			0x208 0x44C 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B1_09_SRC_BT_CFG03			0x208 0x44C 0x0 0x6 0x0
+#define IOMUXC_GPIO_DISP_B1_09_ENET_QOS_TX_DATA00		0x208 0x44C 0x0 0x8 0x0
+#define IOMUXC_GPIO_DISP_B1_09_LPSPI3_PCS2			0x208 0x44C 0x5F8 0x9 0x1
+#define IOMUXC_GPIO_DISP_B1_09_GPIO10_IO30			0x208 0x44C 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_DISP_B1_10_VIDEO_MUX_LCDIF_DATA06		0x20C 0x450 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B1_10_ENET_1G_TX_EN			0x20C 0x450 0x0 0x1 0x0
+#define IOMUXC_GPIO_DISP_B1_10_USDHC1_RESET_B			0x20C 0x450 0x0 0x2 0x0
+#define IOMUXC_GPIO_DISP_B1_10_TMR4_TIMER1			0x20C 0x450 0x664 0x3 0x2
+#define IOMUXC_GPIO_DISP_B1_10_XBAR1_INOUT36			0x20C 0x450 0x0 0x4 0x0
+#define IOMUXC_GPIO_DISP_B1_10_GPIO_MUX4_IO31			0x20C 0x450 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B1_10_SRC_BT_CFG04			0x20C 0x450 0x0 0x6 0x0
+#define IOMUXC_GPIO_DISP_B1_10_ENET_QOS_TX_EN			0x20C 0x450 0x0 0x8 0x0
+#define IOMUXC_GPIO_DISP_B1_10_LPSPI3_PCS3			0x20C 0x450 0x5FC 0x9 0x1
+#define IOMUXC_GPIO_DISP_B1_10_GPIO10_IO31			0x20C 0x450 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_DISP_B1_11_VIDEO_MUX_LCDIF_DATA07		0x210 0x454 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B1_11_ENET_1G_TX_CLK_IO		0x210 0x454 0x4E8 0x1 0x2
+#define IOMUXC_GPIO_DISP_B1_11_ENET_1G_REF_CLK			0x210 0x454 0x4C4 0x2 0x2
+#define IOMUXC_GPIO_DISP_B1_11_TMR4_TIMER2			0x210 0x454 0x668 0x3 0x1
+#define IOMUXC_GPIO_DISP_B1_11_XBAR1_INOUT37			0x210 0x454 0x0 0x4 0x0
+#define IOMUXC_GPIO_DISP_B1_11_GPIO_MUX5_IO00			0x210 0x454 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B1_11_SRC_BT_CFG05			0x210 0x454 0x0 0x6 0x0
+#define IOMUXC_GPIO_DISP_B1_11_ENET_QOS_TX_CLK			0x210 0x454 0x4A4 0x8 0x0
+#define IOMUXC_GPIO_DISP_B1_11_ENET_QOS_REF_CLK			0x210 0x454 0x4A0 0x9 0x2
+#define IOMUXC_GPIO_DISP_B1_11_GPIO11_IO00			0x210 0x454 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_DISP_B2_00_GPIO11_IO01			0x214 0x458 0x0 0xA 0x0
+#define IOMUXC_GPIO_DISP_B2_00_VIDEO_MUX_LCDIF_DATA08		0x214 0x458 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B2_00_WDOG1_B				0x214 0x458 0x0 0x1 0x0
+#define IOMUXC_GPIO_DISP_B2_00_MQS_RIGHT			0x214 0x458 0x0 0x2 0x0
+#define IOMUXC_GPIO_DISP_B2_00_ENET_1G_TX_ER			0x214 0x458 0x0 0x3 0x0
+#define IOMUXC_GPIO_DISP_B2_00_SAI1_TX_DATA03			0x214 0x458 0x0 0x4 0x0
+#define IOMUXC_GPIO_DISP_B2_00_GPIO_MUX5_IO01			0x214 0x458 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B2_00_SRC_BT_CFG06			0x214 0x458 0x0 0x6 0x0
+#define IOMUXC_GPIO_DISP_B2_00_ENET_QOS_TX_ER			0x214 0x458 0x0 0x8 0x0
+
+#define IOMUXC_GPIO_DISP_B2_01_VIDEO_MUX_LCDIF_DATA09		0x218 0x45C 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B2_01_USDHC1_VSELECT			0x218 0x45C 0x0 0x1 0x0
+#define IOMUXC_GPIO_DISP_B2_01_MQS_LEFT				0x218 0x45C 0x0 0x2 0x0
+#define IOMUXC_GPIO_DISP_B2_01_WDOG2_B				0x218 0x45C 0x0 0x3 0x0
+#define IOMUXC_GPIO_DISP_B2_01_SAI1_TX_DATA02			0x218 0x45C 0x0 0x4 0x0
+#define IOMUXC_GPIO_DISP_B2_01_GPIO_MUX5_IO02			0x218 0x45C 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B2_01_SRC_BT_CFG07			0x218 0x45C 0x0 0x6 0x0
+#define IOMUXC_GPIO_DISP_B2_01_EWM_OUT_B			0x218 0x45C 0x0 0x8 0x0
+#define IOMUXC_GPIO_DISP_B2_01_CCM_ENET_REF_CLK_25M		0x218 0x45C 0x0 0x9 0x0
+#define IOMUXC_GPIO_DISP_B2_01_GPIO11_IO02			0x218 0x45C 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_DISP_B2_02_GPIO11_IO03			0x21C 0x460 0x0 0xA 0x0
+#define IOMUXC_GPIO_DISP_B2_02_VIDEO_MUX_LCDIF_DATA10		0x21C 0x460 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B2_02_ENET_TX_DATA00			0x21C 0x460 0x0 0x1 0x0
+#define IOMUXC_GPIO_DISP_B2_02_PIT1_TRIGGER3			0x21C 0x460 0x0 0x2 0x0
+#define IOMUXC_GPIO_DISP_B2_02_ARM_TRACE00			0x21C 0x460 0x0 0x3 0x0
+#define IOMUXC_GPIO_DISP_B2_02_SAI1_TX_DATA01			0x21C 0x460 0x0 0x4 0x0
+#define IOMUXC_GPIO_DISP_B2_02_GPIO_MUX5_IO03			0x21C 0x460 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B2_02_SRC_BT_CFG08			0x21C 0x460 0x0 0x6 0x0
+#define IOMUXC_GPIO_DISP_B2_02_ENET_QOS_TX_DATA00		0x21C 0x460 0x0 0x8 0x0
+
+#define IOMUXC_GPIO_DISP_B2_03_GPIO11_IO04			0x220 0x464 0x0 0xA 0x0
+#define IOMUXC_GPIO_DISP_B2_03_VIDEO_MUX_LCDIF_DATA11		0x220 0x464 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B2_03_ENET_TX_DATA01			0x220 0x464 0x0 0x1 0x0
+#define IOMUXC_GPIO_DISP_B2_03_PIT1_TRIGGER2			0x220 0x464 0x0 0x2 0x0
+#define IOMUXC_GPIO_DISP_B2_03_ARM_TRACE01			0x220 0x464 0x0 0x3 0x0
+#define IOMUXC_GPIO_DISP_B2_03_SAI1_MCLK			0x220 0x464 0x66C 0x4 0x1
+#define IOMUXC_GPIO_DISP_B2_03_GPIO_MUX5_IO04			0x220 0x464 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B2_03_SRC_BT_CFG09			0x220 0x464 0x0 0x6 0x0
+#define IOMUXC_GPIO_DISP_B2_03_ENET_QOS_TX_DATA01		0x220 0x464 0x0 0x8 0x0
+
+#define IOMUXC_GPIO_DISP_B2_04_VIDEO_MUX_LCDIF_DATA12		0x224 0x468 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B2_04_ENET_TX_EN			0x224 0x468 0x0 0x1 0x0
+#define IOMUXC_GPIO_DISP_B2_04_PIT1_TRIGGER1			0x224 0x468 0x0 0x2 0x0
+#define IOMUXC_GPIO_DISP_B2_04_ARM_TRACE02			0x224 0x468 0x0 0x3 0x0
+#define IOMUXC_GPIO_DISP_B2_04_SAI1_RX_SYNC			0x224 0x468 0x678 0x4 0x1
+#define IOMUXC_GPIO_DISP_B2_04_GPIO_MUX5_IO05			0x224 0x468 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B2_04_SRC_BT_CFG10			0x224 0x468 0x0 0x6 0x0
+#define IOMUXC_GPIO_DISP_B2_04_ENET_QOS_TX_EN			0x224 0x468 0x0 0x8 0x0
+#define IOMUXC_GPIO_DISP_B2_04_GPIO11_IO05			0x224 0x468 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_DISP_B2_05_GPIO11_IO06			0x228 0x46C 0x0 0xA 0x0
+#define IOMUXC_GPIO_DISP_B2_05_VIDEO_MUX_LCDIF_DATA13		0x228 0x46C 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B2_05_ENET_TX_CLK			0x228 0x46C 0x4C0 0x1 0x1
+#define IOMUXC_GPIO_DISP_B2_05_ENET_REF_CLK			0x228 0x46C 0x4A8 0x2 0x1
+#define IOMUXC_GPIO_DISP_B2_05_ARM_TRACE03			0x228 0x46C 0x0 0x3 0x0
+#define IOMUXC_GPIO_DISP_B2_05_SAI1_RX_BCLK			0x228 0x46C 0x670 0x4 0x1
+#define IOMUXC_GPIO_DISP_B2_05_GPIO_MUX5_IO06			0x228 0x46C 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B2_05_SRC_BT_CFG11			0x228 0x46C 0x0 0x6 0x0
+#define IOMUXC_GPIO_DISP_B2_05_ENET_QOS_TX_CLK			0x228 0x46C 0x4A4 0x8 0x1
+
+#define IOMUXC_GPIO_DISP_B2_06_GPIO11_IO07			0x22C 0x470 0x0 0xA 0x0
+#define IOMUXC_GPIO_DISP_B2_06_VIDEO_MUX_LCDIF_DATA14		0x22C 0x470 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B2_06_ENET_RX_DATA00			0x22C 0x470 0x4B0 0x1 0x1
+#define IOMUXC_GPIO_DISP_B2_06_LPUART7_TXD			0x22C 0x470 0x630 0x2 0x1
+#define IOMUXC_GPIO_DISP_B2_06_ARM_TRACE_CLK			0x22C 0x470 0x0 0x3 0x0
+#define IOMUXC_GPIO_DISP_B2_06_SAI1_RX_DATA00			0x22C 0x470 0x674 0x4 0x1
+#define IOMUXC_GPIO_DISP_B2_06_GPIO_MUX5_IO07			0x22C 0x470 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B2_06_ENET_QOS_RX_DATA00		0x22C 0x470 0x4F0 0x8 0x1
+
+#define IOMUXC_GPIO_DISP_B2_07_VIDEO_MUX_LCDIF_DATA15		0x230 0x474 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B2_07_ENET_RX_DATA01			0x230 0x474 0x4B4 0x1 0x1
+#define IOMUXC_GPIO_DISP_B2_07_LPUART7_RXD			0x230 0x474 0x62C 0x2 0x1
+#define IOMUXC_GPIO_DISP_B2_07_ARM_TRACE_SWO			0x230 0x474 0x0 0x3 0x0
+#define IOMUXC_GPIO_DISP_B2_07_SAI1_TX_DATA00			0x230 0x474 0x0 0x4 0x0
+#define IOMUXC_GPIO_DISP_B2_07_GPIO_MUX5_IO08			0x230 0x474 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B2_07_ENET_QOS_RX_DATA01		0x230 0x474 0x4F4 0x8 0x1
+#define IOMUXC_GPIO_DISP_B2_07_GPIO11_IO08			0x230 0x474 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_DISP_B2_08_GPIO11_IO09			0x234 0x478 0x0 0xA 0x0
+#define IOMUXC_GPIO_DISP_B2_08_VIDEO_MUX_LCDIF_DATA16		0x234 0x478 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B2_08_ENET_RX_EN			0x234 0x478 0x4B8 0x1 0x1
+#define IOMUXC_GPIO_DISP_B2_08_LPUART8_TXD			0x234 0x478 0x638 0x2 0x1
+#define IOMUXC_GPIO_DISP_B2_08_ARM_CM7_EVENTO			0x234 0x478 0x0 0x3 0x0
+#define IOMUXC_GPIO_DISP_B2_08_SAI1_TX_BCLK			0x234 0x478 0x67C 0x4 0x1
+#define IOMUXC_GPIO_DISP_B2_08_GPIO_MUX5_IO09			0x234 0x478 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B2_08_ENET_QOS_RX_EN			0x234 0x478 0x4F8 0x8 0x1
+#define IOMUXC_GPIO_DISP_B2_08_LPUART1_TXD			0x234 0x478 0x620 0x9 0x2
+
+#define IOMUXC_GPIO_DISP_B2_09_GPIO11_IO10			0x238 0x47C 0x0 0xA 0x0
+#define IOMUXC_GPIO_DISP_B2_09_VIDEO_MUX_LCDIF_DATA17		0x238 0x47C 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B2_09_ENET_RX_ER			0x238 0x47C 0x4BC 0x1 0x1
+#define IOMUXC_GPIO_DISP_B2_09_LPUART8_RXD			0x238 0x47C 0x634 0x2 0x1
+#define IOMUXC_GPIO_DISP_B2_09_ARM_CM7_EVENTI			0x238 0x47C 0x0 0x3 0x0
+#define IOMUXC_GPIO_DISP_B2_09_SAI1_TX_SYNC			0x238 0x47C 0x680 0x4 0x1
+#define IOMUXC_GPIO_DISP_B2_09_GPIO_MUX5_IO10			0x238 0x47C 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B2_09_ENET_QOS_RX_ER			0x238 0x47C 0x4FC 0x8 0x1
+#define IOMUXC_GPIO_DISP_B2_09_LPUART1_RXD			0x238 0x47C 0x61C 0x9 0x2
+
+#define IOMUXC_GPIO_DISP_B2_10_GPIO11_IO11			0x23C 0x480 0x0 0xA 0x0
+#define IOMUXC_GPIO_DISP_B2_10_VIDEO_MUX_LCDIF_DATA18		0x23C 0x480 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B2_10_EMVSIM2_IO			0x23C 0x480 0x6A8 0x1 0x1
+#define IOMUXC_GPIO_DISP_B2_10_LPUART2_TXD			0x23C 0x480 0x0 0x2 0x0
+#define IOMUXC_GPIO_DISP_B2_10_WDOG2_RESET_B_DEB		0x23C 0x480 0x0 0x3 0x0
+#define IOMUXC_GPIO_DISP_B2_10_XBAR1_INOUT38			0x23C 0x480 0x0 0x4 0x0
+#define IOMUXC_GPIO_DISP_B2_10_GPIO_MUX5_IO11			0x23C 0x480 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B2_10_LPI2C3_SCL			0x23C 0x480 0x5BC 0x6 0x1
+#define IOMUXC_GPIO_DISP_B2_10_ENET_QOS_RX_ER			0x23C 0x480 0x4FC 0x8 0x2
+#define IOMUXC_GPIO_DISP_B2_10_SPDIF_IN				0x23C 0x480 0x6B4 0x9 0x2
+
+#define IOMUXC_GPIO_DISP_B2_11_VIDEO_MUX_LCDIF_DATA19		0x240 0x484 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B2_11_EMVSIM2_CLK			0x240 0x484 0x0 0x1 0x0
+#define IOMUXC_GPIO_DISP_B2_11_LPUART2_RXD			0x240 0x484 0x0 0x2 0x0
+#define IOMUXC_GPIO_DISP_B2_11_WDOG1_RESET_B_DEB		0x240 0x484 0x0 0x3 0x0
+#define IOMUXC_GPIO_DISP_B2_11_XBAR1_INOUT39			0x240 0x484 0x0 0x4 0x0
+#define IOMUXC_GPIO_DISP_B2_11_GPIO_MUX5_IO12			0x240 0x484 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B2_11_LPI2C3_SDA			0x240 0x484 0x5C0 0x6 0x1
+#define IOMUXC_GPIO_DISP_B2_11_ENET_QOS_CRS			0x240 0x484 0x0 0x8 0x0
+#define IOMUXC_GPIO_DISP_B2_11_SPDIF_OUT			0x240 0x484 0x0 0x9 0x0
+#define IOMUXC_GPIO_DISP_B2_11_GPIO11_IO12			0x240 0x484 0x0 0xA 0x0
+
+#define IOMUXC_GPIO_DISP_B2_12_GPIO11_IO13			0x244 0x488 0x0 0xA 0x0
+#define IOMUXC_GPIO_DISP_B2_12_VIDEO_MUX_LCDIF_DATA20		0x244 0x488 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B2_12_EMVSIM2_RST			0x244 0x488 0x0 0x1 0x0
+#define IOMUXC_GPIO_DISP_B2_12_FLEXCAN1_TX			0x244 0x488 0x0 0x2 0x0
+#define IOMUXC_GPIO_DISP_B2_12_LPUART2_CTS_B			0x244 0x488 0x0 0x3 0x0
+#define IOMUXC_GPIO_DISP_B2_12_XBAR1_INOUT40			0x244 0x488 0x0 0x4 0x0
+#define IOMUXC_GPIO_DISP_B2_12_GPIO_MUX5_IO13			0x244 0x488 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B2_12_LPI2C4_SCL			0x244 0x488 0x5C4 0x6 0x1
+#define IOMUXC_GPIO_DISP_B2_12_ENET_QOS_COL			0x244 0x488 0x0 0x8 0x0
+#define IOMUXC_GPIO_DISP_B2_12_LPSPI4_SCK			0x244 0x488 0x610 0x9 0x1
+
+#define IOMUXC_GPIO_DISP_B2_13_GPIO11_IO14			0x248 0x48C 0x0 0xA 0x0
+#define IOMUXC_GPIO_DISP_B2_13_VIDEO_MUX_LCDIF_DATA21		0x248 0x48C 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B2_13_EMVSIM2_SVEN			0x248 0x48C 0x0 0x1 0x0
+#define IOMUXC_GPIO_DISP_B2_13_FLEXCAN1_RX			0x248 0x48C 0x498 0x2 0x1
+#define IOMUXC_GPIO_DISP_B2_13_LPUART2_RTS_B			0x248 0x48C 0x0 0x3 0x0
+#define IOMUXC_GPIO_DISP_B2_13_ENET_REF_CLK			0x248 0x48C 0x4A8 0x4 0x2
+#define IOMUXC_GPIO_DISP_B2_13_GPIO_MUX5_IO14			0x248 0x48C 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B2_13_LPI2C4_SDA			0x248 0x48C 0x5C8 0x6 0x1
+#define IOMUXC_GPIO_DISP_B2_13_ENET_QOS_1588_EVENT0_OUT		0x248 0x48C 0x0 0x8 0x0
+#define IOMUXC_GPIO_DISP_B2_13_LPSPI4_SIN			0x248 0x48C 0x614 0x9 0x1
+
+#define IOMUXC_GPIO_DISP_B2_14_GPIO_MUX5_IO15			0x24C 0x490 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B2_14_FLEXCAN1_TX			0x24C 0x490 0x0 0x6 0x0
+#define IOMUXC_GPIO_DISP_B2_14_ENET_QOS_1588_EVENT0_IN		0x24C 0x490 0x0 0x8 0x0
+#define IOMUXC_GPIO_DISP_B2_14_LPSPI4_SOUT			0x24C 0x490 0x618 0x9 0x1
+#define IOMUXC_GPIO_DISP_B2_14_GPIO11_IO15			0x24C 0x490 0x0 0xA 0x0
+#define IOMUXC_GPIO_DISP_B2_14_VIDEO_MUX_LCDIF_DATA22		0x24C 0x490 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B2_14_EMVSIM2_PD			0x24C 0x490 0x6AC 0x1 0x1
+#define IOMUXC_GPIO_DISP_B2_14_WDOG2_B				0x24C 0x490 0x0 0x2 0x0
+#define IOMUXC_GPIO_DISP_B2_14_VIDEO_MUX_EXT_DCIC1		0x24C 0x490 0x0 0x3 0x0
+#define IOMUXC_GPIO_DISP_B2_14_ENET_1G_REF_CLK			0x24C 0x490 0x4C4 0x4 0x3
+
+#define IOMUXC_GPIO_DISP_B2_15_VIDEO_MUX_LCDIF_DATA23		0x250 0x494 0x0 0x0 0x0
+#define IOMUXC_GPIO_DISP_B2_15_EMVSIM2_POWER_FAIL		0x250 0x494 0x6B0 0x1 0x1
+#define IOMUXC_GPIO_DISP_B2_15_WDOG1_B				0x250 0x494 0x0 0x2 0x0
+#define IOMUXC_GPIO_DISP_B2_15_VIDEO_MUX_EXT_DCIC2		0x250 0x494 0x0 0x3 0x0
+#define IOMUXC_GPIO_DISP_B2_15_PIT1_TRIGGER0			0x250 0x494 0x0 0x4 0x0
+#define IOMUXC_GPIO_DISP_B2_15_GPIO_MUX5_IO16			0x250 0x494 0x0 0x5 0x0
+#define IOMUXC_GPIO_DISP_B2_15_FLEXCAN1_RX			0x250 0x494 0x498 0x6 0x2
+#define IOMUXC_GPIO_DISP_B2_15_ENET_QOS_1588_EVENT0_AUX_IN	0x250 0x494 0x0 0x8 0x0
+#define IOMUXC_GPIO_DISP_B2_15_LPSPI4_PCS0			0x250 0x494 0x60C 0x9 0x1
+#define IOMUXC_GPIO_DISP_B2_15_GPIO11_IO16			0x250 0x494 0x0 0xA 0x0
+
+#endif  /* _DT_BINDINGS_PINCTRL_IMXRT1170_PINFUNC_H */
diff --git a/arch/arm/boot/dts/integratorap-im-pd1.dts b/arch/arm/boot/dts/integratorap-im-pd1.dts
index d47bfb66d069..cc514cf07bff 100644
--- a/arch/arm/boot/dts/integratorap-im-pd1.dts
+++ b/arch/arm/boot/dts/integratorap-im-pd1.dts
@@ -178,12 +178,12 @@
 		clock-names = "uartclk", "apb_pclk";
 	};
 
-	ssp@300000 {
+	spi@300000 {
 		compatible = "arm,pl022", "arm,primecell";
 		reg = <0x00300000 0x1000>;
 		interrupts-extended = <&impd1_vic 3>;
 		clocks = <&impd1_sspclk>, <&sysclk>;
-		clock-names = "spiclk", "apb_pclk";
+		clock-names = "sspclk", "apb_pclk";
 	};
 
 	impd1_gpio0: gpio@400000 {
@@ -249,6 +249,7 @@
 		/* 640x480 16bpp @ 25.175MHz is 36827428 bytes/s */
 		max-memory-bandwidth = <40000000>;
 		memory-region = <&impd1_ram>;
+		dma-ranges;
 
 		port@0 {
 			#address-cells = <1>;
diff --git a/arch/arm/boot/dts/integratorap.dts b/arch/arm/boot/dts/integratorap.dts
index 9b652cc27b14..9148287fa0a9 100644
--- a/arch/arm/boot/dts/integratorap.dts
+++ b/arch/arm/boot/dts/integratorap.dts
@@ -160,6 +160,7 @@
 
 	pci: pciv3@62000000 {
 		compatible = "arm,integrator-ap-pci", "v3,v360epc-pci";
+		device_type = "pci";
 		#interrupt-cells = <1>;
 		#size-cells = <2>;
 		#address-cells = <3>;
@@ -261,7 +262,7 @@
 		lm0: bus@c0000000 {
 			compatible = "simple-bus";
 			ranges = <0x00000000 0xc0000000 0x10000000>;
-			dma-ranges = <0x00000000 0x80000000 0x10000000>;
+			dma-ranges = <0x00000000 0xc0000000 0x10000000>;
 			reg = <0xc0000000 0x10000000>;
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -269,7 +270,7 @@
 		lm1: bus@d0000000 {
 			compatible = "simple-bus";
 			ranges = <0x00000000 0xd0000000 0x10000000>;
-			dma-ranges = <0x00000000 0x80000000 0x10000000>;
+			dma-ranges = <0x00000000 0xd0000000 0x10000000>;
 			reg = <0xd0000000 0x10000000>;
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -277,7 +278,7 @@
 		lm2: bus@e0000000 {
 			compatible = "simple-bus";
 			ranges = <0x00000000 0xe0000000 0x10000000>;
-			dma-ranges = <0x00000000 0x80000000 0x10000000>;
+			dma-ranges = <0x00000000 0xe0000000 0x10000000>;
 			reg = <0xe0000000 0x10000000>;
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -285,7 +286,7 @@
 		lm3: bus@f0000000 {
 			compatible = "simple-bus";
 			ranges = <0x00000000 0xf0000000 0x10000000>;
-			dma-ranges = <0x00000000 0x80000000 0x10000000>;
+			dma-ranges = <0x00000000 0xf0000000 0x10000000>;
 			reg = <0xf0000000 0x10000000>;
 			#address-cells = <1>;
 			#size-cells = <1>;
diff --git a/arch/arm/boot/dts/intel-ixp42x-freecom-fsg-3.dts b/arch/arm/boot/dts/intel-ixp42x-freecom-fsg-3.dts
index 598586fc0862..b740403b05a9 100644
--- a/arch/arm/boot/dts/intel-ixp42x-freecom-fsg-3.dts
+++ b/arch/arm/boot/dts/intel-ixp42x-freecom-fsg-3.dts
@@ -97,6 +97,65 @@
 					fis-index-block = <0x1f>;
 				};
 			};
+
+			/* Small syscon with some LEDs at CS2 */
+			syscon@2,0 {
+				compatible = "freecom,fsg-cs2-system-controller", "syscon";
+				reg = <2 0x0 0x200>;
+				reg-io-width = <2>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <2 0x0 0x0 0x200>;
+
+				led@0,0 {
+					compatible = "register-bit-led";
+					reg = <0x00 0x02>;
+					mask = <0x01>;
+					label = "fsg:blue:wlan";
+					linux,default-trigger = "wlan";
+					default-state = "on";
+				};
+				led@0,1 {
+					compatible = "register-bit-led";
+					reg = <0x00 0x02>;
+					mask = <0x02>;
+					label = "fsg:blue:wan";
+					linux,default-trigger = "";
+					default-state = "on";
+				};
+				led@0,2 {
+					compatible = "register-bit-led";
+					reg = <0x00 0x02>;
+					mask = <0x04>;
+					label = "fsg:blue:sata";
+					linux,default-trigger = "";
+					default-state = "on";
+				};
+				led@0,3 {
+					compatible = "register-bit-led";
+					reg = <0x00 0x02>;
+					mask = <0x04>;
+					label = "fsg:blue:usb";
+					linux,default-trigger = "";
+					default-state = "on";
+				};
+				led@0,4 {
+					compatible = "register-bit-led";
+					reg = <0x00 0x02>;
+					mask = <0x08>;
+					label = "fsg:blue:sync";
+					linux,default-trigger = "";
+					default-state = "on";
+				};
+				led@0,5 {
+					compatible = "register-bit-led";
+					reg = <0x00 0x02>;
+					mask = <0x10>;
+					label = "fsg:blue:ring";
+					linux,default-trigger = "";
+					default-state = "on";
+				};
+			};
 		};
 
 		pci@c0000000 {
diff --git a/arch/arm/boot/dts/intel-ixp42x-gateway-7001.dts b/arch/arm/boot/dts/intel-ixp42x-gateway-7001.dts
new file mode 100644
index 000000000000..b7cbc90e1c18
--- /dev/null
+++ b/arch/arm/boot/dts/intel-ixp42x-gateway-7001.dts
@@ -0,0 +1,110 @@
+// SPDX-License-Identifier: ISC
+/*
+ * Device Tree file for Gateway 7001 AP based on IXP422
+ * Derived from boardfiles written by Imre Kaloz
+ */
+
+/dts-v1/;
+
+#include "intel-ixp42x.dtsi"
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "Gateway 7001 AP";
+	compatible = "gateway,7001", "intel,ixp42x";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	memory@0 {
+		/* 32 MB SDRAM */
+		device_type = "memory";
+		reg = <0x00000000 0x2000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8";
+		stdout-path = "uart1:115200n8";
+	};
+
+	aliases {
+		/* second UART is the primary console */
+		serial0 = &uart1;
+	};
+
+	soc {
+		bus@c4000000 {
+			flash@0,0 {
+				compatible = "intel,ixp4xx-flash", "cfi-flash";
+				bank-width = <2>;
+				/*
+				 * 8 MB of flash
+				 */
+				reg = <0 0x00000000 0x800000>;
+
+				/* Configure expansion bus to allow writes */
+				intel,ixp4xx-eb-write-enable = <1>;
+
+				partitions {
+					compatible = "redboot-fis";
+					/* Eraseblock at 0x7e0000 */
+					fis-index-block = <0x3f>;
+				};
+			};
+		};
+
+		pci@c0000000 {
+			status = "ok";
+
+			/*
+			 * Taken from Gateway 7001 PCI boardfile (gateway7001-pci.c)
+			 * We have slots (IDSEL) 1 and 2 with one assigned IRQ
+			 * each handling all IRQs.
+			 */
+			interrupt-map =
+			/* IDSEL 1 */
+			<0x0800 0 0 1 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 1 is irq 11 */
+			<0x0800 0 0 2 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 1 is irq 11 */
+			<0x0800 0 0 3 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 1 is irq 11 */
+			<0x0800 0 0 4 &gpio0 11 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 1 is irq 11 */
+			/* IDSEL 2 */
+			<0x1000 0 0 1 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 2 is irq 10 */
+			<0x1000 0 0 2 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 2 is irq 10 */
+			<0x1000 0 0 3 &gpio0 10 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 2 is irq 10 */
+			<0x1000 0 0 4 &gpio0 10 IRQ_TYPE_LEVEL_LOW>; /* INT D on slot 2 is irq 10 */
+		};
+
+		ethernet@c8009000 {
+			status = "ok";
+			queue-rx = <&qmgr 3>;
+			queue-txready = <&qmgr 20>;
+			phy-mode = "rgmii";
+			phy-handle = <&phy1>;
+
+			mdio {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				phy1: ethernet-phy@1 {
+					reg = <1>;
+				};
+			};
+		};
+
+		ethernet@c800a000 {
+			status = "ok";
+			queue-rx = <&qmgr 4>;
+			queue-txready = <&qmgr 21>;
+			phy-mode = "rgmii";
+			phy-handle = <&phy2>;
+
+			mdio {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				phy2: ethernet-phy@2 {
+					reg = <2>;
+				};
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/intel-ixp42x-goramo-multilink.dts b/arch/arm/boot/dts/intel-ixp42x-goramo-multilink.dts
new file mode 100644
index 000000000000..f80388b17a9e
--- /dev/null
+++ b/arch/arm/boot/dts/intel-ixp42x-goramo-multilink.dts
@@ -0,0 +1,180 @@
+// SPDX-License-Identifier: ISC
+/*
+ * Device Tree file for the Goramo MultiLink Router
+ * There are two variants:
+ * - MultiLink Basic (a box)
+ * - MultiLink Max (19" rack mount)
+ * This device tree supports MultiLink Basic.
+ * This machine is based on IXP425.
+ * This is one of the few devices supporting the IXP4xx High-Speed Serial
+ * (HSS) link for a V.35 WAN interface.
+ * The hardware originates in Poland.
+ */
+
+/dts-v1/;
+
+#include "intel-ixp42x.dtsi"
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "Goramo MultiLink Router";
+	compatible = "goramo,multilink-router", "intel,ixp42x";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	memory@0 {
+		/*
+		 * 64 MB of RAM according to the manual. The MultiLink
+		 * Max has 128 MB.
+		 */
+		device_type = "memory";
+		reg = <0x00000000 0x4000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8";
+		stdout-path = "uart0:115200n8";
+	};
+
+	aliases {
+		serial0 = &uart0;
+		serial1 = &uart1;
+	};
+
+	/*
+	 * 74HC4094 which is used as a rudimentary GPIO expander
+	 * FIXME:
+	 * - Create device tree bindings for this as GPIO expander
+	 * - Write a pure DT GPIO driver using these bindings
+	 * - Support cascading in the style of gpio-74x164.c (cannot be reused, very different)
+	 */
+	gpio_74: gpio-74hc4094 {
+		compatible = "nxp,74hc4094";
+		cp-gpios = <&gpio0 0 GPIO_ACTIVE_HIGH>;
+		d-gpios = <&gpio0 1 GPIO_ACTIVE_HIGH>;
+		str-gpios = <&gpio0 2 GPIO_ACTIVE_HIGH>;
+		/* oe-gpios is optional */
+		gpio-controller;
+		#gpio-cells = <2>;
+		/* We are not cascaded */
+		registers-number = <1>;
+		gpio-line-names = "CONTROL_HSS0_CLK_INT", "CONTROL_HSS1_CLK_INT", "CONTROL_HSS0_DTR_N",
+				"CONTROL_HSS1_DTR_N", "CONTROL_EXT", "CONTROL_AUTO_RESET",
+				"CONTROL_PCI_RESET_N", "CONTROL_EEPROM_WC_N";
+	};
+
+	soc {
+		bus@c4000000 {
+			flash@0,0 {
+				compatible = "intel,ixp4xx-flash", "cfi-flash";
+				bank-width = <2>;
+				/* Enable writes on the expansion bus */
+				intel,ixp4xx-eb-write-enable = <1>;
+				/* 16 MB of Flash mapped in at CS0 */
+				reg = <0 0x00000000 0x1000000>;
+
+				partitions {
+					compatible = "redboot-fis";
+					/* Eraseblock at 0x0fe0000 */
+					fis-index-block = <0x7f>;
+				};
+			};
+		};
+
+		pci@c0000000 {
+			status = "ok";
+
+			/*
+			 * The device has 4 slots (IDSEL) with one dedicated IRQ per slot.
+			 * The slots have Ethernet, Ethernet, NEC and MPCI.
+			 * The IDSELs are 11, 12, 13, 14.
+			 */
+			interrupt-map =
+			/* IDSEL 11 - Ethernet A */
+			<0x5800 0 0 1 &gpio0 4 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 11 is irq 4 */
+			<0x5800 0 0 2 &gpio0 4 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 11 is irq 4 */
+			<0x5800 0 0 3 &gpio0 4 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 11 is irq 4 */
+			<0x5800 0 0 4 &gpio0 4 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 11 is irq 4 */
+			/* IDSEL 12 - Ethernet B */
+			<0x6000 0 0 1 &gpio0 5 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 12 is irq 5 */
+			<0x6000 0 0 2 &gpio0 5 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 12 is irq 5 */
+			<0x6000 0 0 3 &gpio0 5 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 12 is irq 5 */
+			<0x6000 0 0 4 &gpio0 5 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 12 is irq 5 */
+			/* IDSEL 13 - MPCI */
+			<0x6800 0 0 1 &gpio0 12 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 13 is irq 12 */
+			<0x6800 0 0 2 &gpio0 12 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 13 is irq 12 */
+			<0x6800 0 0 3 &gpio0 12 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 13 is irq 12 */
+			<0x6800 0 0 4 &gpio0 12 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 13 is irq 12 */
+			/* IDSEL 14 - NEC */
+			<0x7000 0 0 1 &gpio0 3 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 14 is irq 3 */
+			<0x7000 0 0 2 &gpio0 3 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 14 is irq 3 */
+			<0x7000 0 0 3 &gpio0 3 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 14 is irq 3 */
+			<0x7000 0 0 4 &gpio0 3 IRQ_TYPE_LEVEL_LOW>; /* INT D on slot 14 is irq 3 */
+		};
+
+		/* HSS links */
+		npe@c8006000 {
+			hss@0 {
+				status = "okay";
+				intel,queue-chl-rxtrig = <&qmgr 12>;
+				intel,queue-chl-txready = <&qmgr 34>;
+				intel,queue-pkt-rx = <&qmgr 13>;
+				intel,queue-pkt-tx = <&qmgr 14>, <&qmgr 15>, <&qmgr 16>, <&qmgr 17>;
+				intel,queue-pkt-rxfree = <&qmgr 18>, <&qmgr 19>, <&qmgr 20>, <&qmgr 21>;
+				intel,queue-pkt-txdone = <&qmgr 22>;
+				/* The Goramo GPIO-based clock etc control */
+				cts-gpios = <&gpio0 10 GPIO_ACTIVE_LOW>;
+				rts-gpios = <&gpio0 14 GPIO_ACTIVE_LOW>;
+				dcd-gpios = <&gpio0 6 GPIO_ACTIVE_LOW>;
+				dtr-gpios = <&gpio_74 2 GPIO_ACTIVE_LOW>;
+				clk-internal-gpios = <&gpio_74 0 GPIO_ACTIVE_HIGH>;
+			};
+			hss@1 {
+				status = "okay";
+				intel,queue-chl-rxtrig = <&qmgr 10>;
+				intel,queue-chl-txready = <&qmgr 35>;
+				intel,queue-pkt-rx = <&qmgr 0>;
+				intel,queue-pkt-tx = <&qmgr 5>, <&qmgr 6>, <&qmgr 7>, <&qmgr 8>;
+				intel,queue-pkt-rxfree = <&qmgr 1>, <&qmgr 2>, <&qmgr 3>, <&qmgr 4>;
+				intel,queue-pkt-txdone = <&qmgr 9>;
+				/* The Goramo GPIO-based clock etc control */
+				cts-gpios = <&gpio0 11 GPIO_ACTIVE_LOW>;
+				rts-gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
+				dcd-gpios = <&gpio0 7 GPIO_ACTIVE_LOW>;
+				dtr-gpios = <&gpio_74 3 GPIO_ACTIVE_LOW>;
+				clk-internal-gpios = <&gpio_74 1 GPIO_ACTIVE_HIGH>;
+			};
+		};
+
+		/* EthB */
+		ethernet@c8009000 {
+			status = "ok";
+			queue-rx = <&qmgr 3>;
+			queue-txready = <&qmgr 32>;
+			phy-mode = "rgmii";
+			phy-handle = <&phy0>;
+
+			mdio {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				phy0: ethernet-phy@0 {
+					reg = <0>;
+				};
+
+				phy1: ethernet-phy@1 {
+					reg = <1>;
+				};
+			};
+		};
+
+		/* EthC */
+		ethernet@c800a000 {
+			status = "ok";
+			queue-rx = <&qmgr 4>;
+			queue-txready = <&qmgr 33>;
+			phy-mode = "rgmii";
+			phy-handle = <&phy1>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/intel-ixp42x-netgear-wg302v1.dts b/arch/arm/boot/dts/intel-ixp42x-netgear-wg302v1.dts
new file mode 100644
index 000000000000..df2ca6d95ee5
--- /dev/null
+++ b/arch/arm/boot/dts/intel-ixp42x-netgear-wg302v1.dts
@@ -0,0 +1,96 @@
+// SPDX-License-Identifier: ISC
+/*
+ * Device Tree file for Netgear WG302v2 based on IXP422BB
+ * Derived from boardfiles written by Imre Kaloz
+ */
+
+/dts-v1/;
+
+#include "intel-ixp42x.dtsi"
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "Netgear WG302 v1";
+	compatible = "netgear,wg302v1", "intel,ixp42x";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	memory@0 {
+		/* 32 MB SDRAM according to boot arguments */
+		device_type = "memory";
+		reg = <0x00000000 0x02000000>;
+	};
+
+	chosen {
+		/* The RedBoot comes up in 9600 baud so let's keep this */
+		bootargs = "console=ttyS0,9600n8";
+		stdout-path = "uart1:9600n8";
+	};
+
+	aliases {
+		/* These are switched around */
+		serial0 = &uart1;
+	};
+
+	soc {
+		bus@c4000000 {
+			flash@0,0 {
+				compatible = "intel,ixp4xx-flash", "cfi-flash";
+				bank-width = <2>;
+				/*
+				 * 8 MB of Flash in 64 0x20000 sized blocks
+				 * mapped in at CS0.
+				 */
+				reg = <0 0x00000000 0x800000>;
+
+				/* Configure expansion bus to allow writes */
+				intel,ixp4xx-eb-write-enable = <1>;
+
+				partitions {
+					compatible = "redboot-fis";
+					fis-index-block = <0x3f>;
+				};
+			};
+		};
+
+		pci@c0000000 {
+			status = "ok";
+
+			/*
+			 * Taken from WG302 v2 PCI boardfile (wg302v2-pci.c)
+			 * We have slots (IDSEL) 1 and 2 with one assigned IRQ
+			 * each handling all IRQs.
+			 */
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0xf800 0 0 7>;
+			interrupt-map =
+			/* IDSEL 1 */
+			<0x0800 0 0 1 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 1 is irq 8 */
+			<0x0800 0 0 2 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 1 is irq 8 */
+			<0x0800 0 0 3 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 1 is irq 8 */
+			<0x0800 0 0 4 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 1 is irq 8 */
+			/* IDSEL 2 */
+			<0x1000 0 0 1 &gpio0 9 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 2 is irq 9 */
+			<0x1000 0 0 2 &gpio0 9 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 2 is irq 9 */
+			<0x1000 0 0 3 &gpio0 9 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 2 is irq 9 */
+			<0x1000 0 0 4 &gpio0 9 IRQ_TYPE_LEVEL_LOW>; /* INT D on slot 2 is irq 9 */
+		};
+
+		ethernet@c8009000 {
+			status = "ok";
+			queue-rx = <&qmgr 3>;
+			queue-txready = <&qmgr 20>;
+			phy-mode = "rgmii";
+			phy-handle = <&phy30>;
+
+			mdio {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				phy30: ethernet-phy@30 {
+					reg = <30>;
+				};
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/intel-ixp42x-netgear-wg302v2.dts b/arch/arm/boot/dts/intel-ixp42x-netgear-wg302v2.dts
deleted file mode 100644
index a57009436ed8..000000000000
--- a/arch/arm/boot/dts/intel-ixp42x-netgear-wg302v2.dts
+++ /dev/null
@@ -1,97 +0,0 @@
-// SPDX-License-Identifier: ISC
-/*
- * Device Tree file for Netgear WG302v2 based on IXP422BB
- * Derived from boardfiles written by Imre Kaloz
- */
-
-/dts-v1/;
-
-#include "intel-ixp42x.dtsi"
-#include <dt-bindings/input/input.h>
-
-/ {
-	model = "Netgear WG302 v2";
-	compatible = "netgear,wg302v2", "intel,ixp42x";
-	#address-cells = <1>;
-	#size-cells = <1>;
-
-	memory@0 {
-		/* 16 MB SDRAM according to OpenWrt database */
-		device_type = "memory";
-		reg = <0x00000000 0x01000000>;
-	};
-
-	chosen {
-		bootargs = "console=ttyS0,115200n8 root=/dev/sda1 rw rootwait";
-		stdout-path = "uart1:115200n8";
-	};
-
-	aliases {
-		/* These are switched around */
-		serial0 = &uart1;
-		serial1 = &uart0;
-	};
-
-	soc {
-		bus@c4000000 {
-			flash@0,0 {
-				compatible = "intel,ixp4xx-flash", "cfi-flash";
-				bank-width = <2>;
-				/*
-				 * 32 MB of Flash in 128 0x20000 sized blocks
-				 * mapped in at CS0 and CS1
-				 */
-				reg = <0 0x00000000 0x2000000>;
-
-				/* Configure expansion bus to allow writes */
-				intel,ixp4xx-eb-write-enable = <1>;
-
-				partitions {
-					compatible = "redboot-fis";
-					/* CHECKME: guess this is Redboot FIS */
-					fis-index-block = <0xff>;
-				};
-			};
-		};
-
-		pci@c0000000 {
-			status = "ok";
-
-			/*
-			 * Taken from WG302 v2 PCI boardfile (wg302v2-pci.c)
-			 * We have slots (IDSEL) 1 and 2 with one assigned IRQ
-			 * each handling all IRQs.
-			 */
-			#interrupt-cells = <1>;
-			interrupt-map-mask = <0xf800 0 0 7>;
-			interrupt-map =
-			/* IDSEL 1 */
-			<0x0800 0 0 1 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 1 is irq 8 */
-			<0x0800 0 0 2 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 1 is irq 8 */
-			<0x0800 0 0 3 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 1 is irq 8 */
-			<0x0800 0 0 4 &gpio0 8 IRQ_TYPE_LEVEL_LOW>, /* INT D on slot 1 is irq 8 */
-			/* IDSEL 2 */
-			<0x1000 0 0 1 &gpio0 9 IRQ_TYPE_LEVEL_LOW>, /* INT A on slot 2 is irq 9 */
-			<0x1000 0 0 2 &gpio0 9 IRQ_TYPE_LEVEL_LOW>, /* INT B on slot 2 is irq 9 */
-			<0x1000 0 0 3 &gpio0 9 IRQ_TYPE_LEVEL_LOW>, /* INT C on slot 2 is irq 9 */
-			<0x1000 0 0 4 &gpio0 9 IRQ_TYPE_LEVEL_LOW>; /* INT D on slot 2 is irq 9 */
-		};
-
-		ethernet@c8009000 {
-			status = "ok";
-			queue-rx = <&qmgr 3>;
-			queue-txready = <&qmgr 20>;
-			phy-mode = "rgmii";
-			phy-handle = <&phy8>;
-
-			mdio {
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				phy8: ethernet-phy@8 {
-					reg = <8>;
-				};
-			};
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/intel-ixp42x.dtsi b/arch/arm/boot/dts/intel-ixp42x.dtsi
index d0e0f8afb7c9..84cee8ec3ab8 100644
--- a/arch/arm/boot/dts/intel-ixp42x.dtsi
+++ b/arch/arm/boot/dts/intel-ixp42x.dtsi
@@ -9,7 +9,7 @@
 	soc {
 		bus@c4000000 {
 			compatible = "intel,ixp42x-expansion-bus-controller", "syscon";
-			reg = <0xc4000000 0x28>;
+			reg = <0xc4000000 0x30>;
 		};
 
 		pci@c0000000 {
diff --git a/arch/arm/boot/dts/intel-ixp4xx.dtsi b/arch/arm/boot/dts/intel-ixp4xx.dtsi
index 46fede021476..51a716c59669 100644
--- a/arch/arm/boot/dts/intel-ixp4xx.dtsi
+++ b/arch/arm/boot/dts/intel-ixp4xx.dtsi
@@ -139,6 +139,23 @@
 		npe: npe@c8006000 {
 			compatible = "intel,ixp4xx-network-processing-engine";
 			reg = <0xc8006000 0x1000>, <0xc8007000 0x1000>, <0xc8008000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			/* NPE-A contains two high-speed serial links */
+			hss@0 {
+				compatible = "intel,ixp4xx-hss";
+				reg = <0>;
+				intel,npe-handle = <&npe 0>;
+				status = "disabled";
+			};
+
+			hss@1 {
+				compatible = "intel,ixp4xx-hss";
+				reg = <1>;
+				intel,npe-handle = <&npe 0>;
+				status = "disabled";
+			};
 
 			/* NPE-C contains a crypto accelerator */
 			crypto {
diff --git a/arch/arm/boot/dts/iwg20d-q7-common.dtsi b/arch/arm/boot/dts/iwg20d-q7-common.dtsi
index 849034a49a3f..03caea6fc6ff 100644
--- a/arch/arm/boot/dts/iwg20d-q7-common.dtsi
+++ b/arch/arm/boot/dts/iwg20d-q7-common.dtsi
@@ -181,7 +181,7 @@
 };
 
 &gpio2 {
-	touch-interrupt {
+	touch-interrupt-hog {
 		gpio-hog;
 		gpios = <12 GPIO_ACTIVE_LOW>;
 		input;
diff --git a/arch/arm/boot/dts/keystone-k2e-evm.dts b/arch/arm/boot/dts/keystone-k2e-evm.dts
index 66fec5f5d081..5d6d074011df 100644
--- a/arch/arm/boot/dts/keystone-k2e-evm.dts
+++ b/arch/arm/boot/dts/keystone-k2e-evm.dts
@@ -137,10 +137,10 @@
 };
 
 &spi0 {
-	nor_flash: n25q128a11@0 {
+	nor_flash: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		compatible = "Micron,n25q128a11";
+		compatible = "micron,n25q128a11", "jedec,spi-nor";
 		spi-max-frequency = <54000000>;
 		m25p,fast-read;
 		reg = <0>;
diff --git a/arch/arm/boot/dts/keystone-k2e-netcp.dtsi b/arch/arm/boot/dts/keystone-k2e-netcp.dtsi
index 71064483d34f..42cf74db673c 100644
--- a/arch/arm/boot/dts/keystone-k2e-netcp.dtsi
+++ b/arch/arm/boot/dts/keystone-k2e-netcp.dtsi
@@ -12,9 +12,9 @@ qmss: qmss@2a40000 {
 	#size-cells = <1>;
 	clocks = <&chipclk13>;
 	ranges;
-	queue-range	= <0 0x2000>;
-	linkram0	= <0x100000 0x4000>;
-	linkram1	= <0 0x10000>;
+	queue-range = <0 0x2000>;
+	linkram0 = <0x100000 0x4000>;
+	linkram1 = <0 0x10000>;
 
 	qmgrs {
 		#address-cells = <1>;
@@ -176,40 +176,40 @@ netcp: netcp@24000000 {
 			interfaces {
 				gbe0: interface-0 {
 					slave-port = <0>;
-					link-interface	= <1>;
-					phy-handle	= <&ethphy0>;
+					link-interface = <1>;
+					phy-handle = <&ethphy0>;
 				};
 				gbe1: interface-1 {
 					slave-port = <1>;
-					link-interface	= <1>;
-					phy-handle	= <&ethphy1>;
+					link-interface = <1>;
+					phy-handle = <&ethphy1>;
 				};
 			};
 
 			secondary-slave-ports {
 				port-2 {
 					slave-port = <2>;
-					link-interface	= <2>;
+					link-interface = <2>;
 				};
 				port-3 {
 					slave-port = <3>;
-					link-interface	= <2>;
+					link-interface = <2>;
 				};
 				port-4 {
 					slave-port = <4>;
-					link-interface	= <2>;
+					link-interface = <2>;
 				};
 				port-5 {
 					slave-port = <5>;
-					link-interface	= <2>;
+					link-interface = <2>;
 				};
 				port-6 {
 					slave-port = <6>;
-					link-interface	= <2>;
+					link-interface = <2>;
 				};
 				port-7 {
 					slave-port = <7>;
-					link-interface	= <2>;
+					link-interface = <2>;
 				};
 			};
 		};
diff --git a/arch/arm/boot/dts/keystone-k2e.dtsi b/arch/arm/boot/dts/keystone-k2e.dtsi
index b8f152e7af7f..65c32946c522 100644
--- a/arch/arm/boot/dts/keystone-k2e.dtsi
+++ b/arch/arm/boot/dts/keystone-k2e.dtsi
@@ -141,7 +141,7 @@
 			clock-names = "pcie";
 			#address-cells = <3>;
 			#size-cells = <2>;
-			reg =  <0x21021000 0x2000>, <0x21020000 0x1000>, <0x02620128 4>;
+			reg = <0x21021000 0x2000>, <0x21020000 0x1000>, <0x02620128 4>;
 			ranges = <0x82000000 0 0x60000000 0x60000000
 				  0 0x10000000>;
 
@@ -185,14 +185,14 @@
 		};
 
 		mdio: mdio@24200f00 {
-			compatible	= "ti,keystone_mdio", "ti,davinci_mdio";
+			compatible = "ti,keystone_mdio", "ti,davinci_mdio";
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <0x24200f00 0x100>;
 			status = "disabled";
 			clocks = <&clkcpgmac>;
 			clock-names = "fck";
-			bus_freq	= <2500000>;
+			bus_freq = <2500000>;
 		};
 		/include/ "keystone-k2e-netcp.dtsi"
 };
diff --git a/arch/arm/boot/dts/keystone-k2g-evm.dts b/arch/arm/boot/dts/keystone-k2g-evm.dts
index d800f26b6275..88be868cf71e 100644
--- a/arch/arm/boot/dts/keystone-k2g-evm.dts
+++ b/arch/arm/boot/dts/keystone-k2g-evm.dts
@@ -392,7 +392,7 @@
 	pinctrl-0 = <&qspi_pins>;
 	cdns,rclk-en;
 
-	flash0: m25p80@0 {
+	flash0: flash@0 {
 		compatible = "s25fl512s", "jedec,spi-nor";
 		reg = <0>;
 		spi-tx-bus-width = <1>;
diff --git a/arch/arm/boot/dts/keystone-k2g-ice.dts b/arch/arm/boot/dts/keystone-k2g-ice.dts
index 2a2d38cf0fff..bd84d7f0f2fe 100644
--- a/arch/arm/boot/dts/keystone-k2g-ice.dts
+++ b/arch/arm/boot/dts/keystone-k2g-ice.dts
@@ -325,7 +325,7 @@
 	cdns,rclk-en;
 	status = "okay";
 
-	flash0: m25p80@0 {
+	flash0: flash@0 {
 		compatible = "s25fl256s1", "jedec,spi-nor";
 		reg = <0>;
 		spi-tx-bus-width = <1>;
diff --git a/arch/arm/boot/dts/keystone-k2g-netcp.dtsi b/arch/arm/boot/dts/keystone-k2g-netcp.dtsi
index d0e6a9a43402..f6306933ff42 100644
--- a/arch/arm/boot/dts/keystone-k2g-netcp.dtsi
+++ b/arch/arm/boot/dts/keystone-k2g-netcp.dtsi
@@ -125,7 +125,7 @@ netcp: netcp@4000000 {
 			interfaces {
 				gbe0: interface-0 {
 					slave-port = <0>;
-					link-interface	= <5>;
+					link-interface = <5>;
 				};
 			};
 		};
diff --git a/arch/arm/boot/dts/keystone-k2g.dtsi b/arch/arm/boot/dts/keystone-k2g.dtsi
index 37198294f4b2..380dd9d637ee 100644
--- a/arch/arm/boot/dts/keystone-k2g.dtsi
+++ b/arch/arm/boot/dts/keystone-k2g.dtsi
@@ -262,7 +262,7 @@
 			 */
 			ti,system-reboot-controller;
 			mbox-names = "rx", "tx";
-			mboxes= <&msgmgr 5 2>,
+			mboxes = <&msgmgr 5 2>,
 				<&msgmgr 0 0>;
 			reg-names = "debug_messages";
 			reg = <0x02921c00 0x400>;
@@ -326,13 +326,13 @@
 
 		dss: dss@02540000 {
 			compatible = "ti,k2g-dss";
-			reg =	<0x02540000 0x400>,
+			reg = <0x02540000 0x400>,
 				<0x02550000 0x1000>,
 				<0x02557000 0x1000>,
 				<0x0255a800 0x100>,
 				<0x0255ac00 0x100>;
 			reg-names = "cfg", "common", "vid1", "ovr1", "vp1";
-			clocks =	<&k2g_clks 0x2 0>,
+			clocks = <&k2g_clks 0x2 0>,
 					<&k2g_clks 0x2 1>;
 			clock-names = "fck", "vp1";
 			interrupts = <GIC_SPI 247 IRQ_TYPE_EDGE_RISING>;
@@ -348,7 +348,7 @@
 
 		edma0: edma@2700000 {
 			compatible = "ti,k2g-edma3-tpcc", "ti,edma3-tpcc";
-			reg =	<0x02700000 0x8000>;
+			reg = <0x02700000 0x8000>;
 			reg-names = "edma3_cc";
 			interrupts = <GIC_SPI 200 IRQ_TYPE_EDGE_RISING>,
 					<GIC_SPI 216 IRQ_TYPE_EDGE_RISING>,
@@ -367,19 +367,19 @@
 
 		edma0_tptc0: tptc@2760000 {
 			compatible = "ti,k2g-edma3-tptc", "ti,edma3-tptc";
-			reg =	<0x02760000 0x400>;
+			reg = <0x02760000 0x400>;
 			power-domains = <&k2g_pds 0x3f>;
 		};
 
 		edma0_tptc1: tptc@2768000 {
 			compatible = "ti,k2g-edma3-tptc", "ti,edma3-tptc";
-			reg =	<0x02768000 0x400>;
+			reg = <0x02768000 0x400>;
 			power-domains = <&k2g_pds 0x3f>;
 		};
 
 		edma1: edma@2728000 {
 			compatible = "ti,k2g-edma3-tpcc", "ti,edma3-tpcc";
-			reg =	<0x02728000 0x8000>;
+			reg = <0x02728000 0x8000>;
 			reg-names = "edma3_cc";
 			interrupts = <GIC_SPI 208 IRQ_TYPE_EDGE_RISING>,
 					<GIC_SPI 219 IRQ_TYPE_EDGE_RISING>,
@@ -402,13 +402,13 @@
 
 		edma1_tptc0: tptc@27b0000 {
 			compatible = "ti,k2g-edma3-tptc", "ti,edma3-tptc";
-			reg =	<0x027b0000 0x400>;
+			reg = <0x027b0000 0x400>;
 			power-domains = <&k2g_pds 0x4f>;
 		};
 
 		edma1_tptc1: tptc@27b8000 {
 			compatible = "ti,k2g-edma3-tptc", "ti,edma3-tptc";
-			reg =	<0x027b8000 0x400>;
+			reg = <0x027b8000 0x400>;
 			power-domains = <&k2g_pds 0x4f>;
 		};
 
diff --git a/arch/arm/boot/dts/keystone-k2hk-evm.dts b/arch/arm/boot/dts/keystone-k2hk-evm.dts
index ad4e22afe133..4a91f5ded402 100644
--- a/arch/arm/boot/dts/keystone-k2hk-evm.dts
+++ b/arch/arm/boot/dts/keystone-k2hk-evm.dts
@@ -161,10 +161,10 @@
 };
 
 &spi0 {
-	nor_flash: n25q128a11@0 {
+	nor_flash: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		compatible = "Micron,n25q128a11";
+		compatible = "micron,n25q128a11", "jedec,spi-nor";
 		spi-max-frequency = <54000000>;
 		m25p,fast-read;
 		reg = <0>;
diff --git a/arch/arm/boot/dts/keystone-k2hk-netcp.dtsi b/arch/arm/boot/dts/keystone-k2hk-netcp.dtsi
index 022d93c366c7..8a421c65f920 100644
--- a/arch/arm/boot/dts/keystone-k2hk-netcp.dtsi
+++ b/arch/arm/boot/dts/keystone-k2hk-netcp.dtsi
@@ -12,9 +12,9 @@ qmss: qmss@2a40000 {
 	#size-cells = <1>;
 	clocks = <&chipclk13>;
 	ranges;
-	queue-range	= <0 0x4000>;
-	linkram0	= <0x100000 0x8000>;
-	linkram1	= <0x0 0x10000>;
+	queue-range = <0 0x4000>;
+	linkram0 = <0x100000 0x8000>;
+	linkram1 = <0x0 0x10000>;
 
 	qmgrs {
 		#address-cells = <1>;
@@ -150,7 +150,7 @@ netcp: netcp@2000000 {
 	#size-cells = <1>;
 
 	/* NetCP address range */
-	ranges  = <0 0x2000000 0x100000>;
+	ranges = <0 0x2000000 0x100000>;
 
 	clocks = <&clkpa>, <&clkcpgmac>;
 	clock-names = "pa_clk", "ethss_clk";
@@ -207,11 +207,11 @@ netcp: netcp@2000000 {
 			secondary-slave-ports {
 				port-2 {
 					slave-port = <2>;
-					link-interface	= <2>;
+					link-interface = <2>;
 				};
 				port-3 {
 					slave-port = <3>;
-					link-interface	= <2>;
+					link-interface = <2>;
 				};
 			};
 		};
diff --git a/arch/arm/boot/dts/keystone-k2hk.dtsi b/arch/arm/boot/dts/keystone-k2hk.dtsi
index 8a9447703310..da6d3934c2e8 100644
--- a/arch/arm/boot/dts/keystone-k2hk.dtsi
+++ b/arch/arm/boot/dts/keystone-k2hk.dtsi
@@ -282,14 +282,14 @@
 		};
 
 		mdio: mdio@2090300 {
-			compatible	= "ti,keystone_mdio", "ti,davinci_mdio";
+			compatible = "ti,keystone_mdio", "ti,davinci_mdio";
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <0x02090300 0x100>;
 			status = "disabled";
 			clocks = <&clkcpgmac>;
 			clock-names = "fck";
-			bus_freq	= <2500000>;
+			bus_freq = <2500000>;
 		};
 		/include/ "keystone-k2hk-netcp.dtsi"
 };
diff --git a/arch/arm/boot/dts/keystone-k2l-evm.dts b/arch/arm/boot/dts/keystone-k2l-evm.dts
index e200533d26a4..1c880cf8fa91 100644
--- a/arch/arm/boot/dts/keystone-k2l-evm.dts
+++ b/arch/arm/boot/dts/keystone-k2l-evm.dts
@@ -110,10 +110,10 @@
 };
 
 &spi0 {
-	nor_flash: n25q128a11@0 {
+	nor_flash: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		compatible = "Micron,n25q128a11";
+		compatible = "micron,n25q128a11", "jedec,spi-nor";
 		spi-max-frequency = <54000000>;
 		m25p,fast-read;
 		reg = <0>;
diff --git a/arch/arm/boot/dts/keystone-k2l-netcp.dtsi b/arch/arm/boot/dts/keystone-k2l-netcp.dtsi
index e96ca664abc2..5ec6680a533d 100644
--- a/arch/arm/boot/dts/keystone-k2l-netcp.dtsi
+++ b/arch/arm/boot/dts/keystone-k2l-netcp.dtsi
@@ -12,9 +12,9 @@ qmss: qmss@2a40000 {
 	#size-cells = <1>;
 	clocks = <&chipclk13>;
 	ranges;
-	queue-range	= <0 0x2000>;
-	linkram0	= <0x100000 0x4000>;
-	linkram1	= <0x70000000 0x10000>; /* 1MB OSR mem */
+	queue-range = <0 0x2000>;
+	linkram0 = <0x100000 0x4000>;
+	linkram1 = <0x70000000 0x10000>; /* 1MB OSR mem */
 
 	qmgrs {
 		#address-cells = <1>;
@@ -174,24 +174,24 @@ netcp: netcp@26000000 {
 			interfaces {
 				gbe0: interface-0 {
 					slave-port = <0>;
-					link-interface	= <1>;
-					phy-handle	= <&ethphy0>;
+					link-interface = <1>;
+					phy-handle = <&ethphy0>;
 				};
 				gbe1: interface-1 {
 					slave-port = <1>;
-					link-interface	= <1>;
-					phy-handle	= <&ethphy1>;
+					link-interface = <1>;
+					phy-handle = <&ethphy1>;
 				};
 			};
 
 			secondary-slave-ports {
 				port-2 {
 					slave-port = <2>;
-					link-interface	= <2>;
+					link-interface = <2>;
 				};
 				port-3 {
 					slave-port = <3>;
-					link-interface	= <2>;
+					link-interface = <2>;
 				};
 			};
 		};
diff --git a/arch/arm/boot/dts/keystone-k2l.dtsi b/arch/arm/boot/dts/keystone-k2l.dtsi
index dff5fea72b2f..421a02bbc9d3 100644
--- a/arch/arm/boot/dts/keystone-k2l.dtsi
+++ b/arch/arm/boot/dts/keystone-k2l.dtsi
@@ -47,7 +47,7 @@
 			reg-shift = <2>;
 			reg-io-width = <4>;
 			reg = <0x02348400 0x100>;
-			clocks	= <&clkuart2>;
+			clocks = <&clkuart2>;
 			interrupts = <GIC_SPI 432 IRQ_TYPE_EDGE_RISING>;
 		};
 
@@ -57,7 +57,7 @@
 			reg-shift = <2>;
 			reg-io-width = <4>;
 			reg = <0x02348800 0x100>;
-			clocks	= <&clkuart3>;
+			clocks = <&clkuart3>;
 			interrupts = <GIC_SPI 435 IRQ_TYPE_EDGE_RISING>;
 		};
 
@@ -388,14 +388,14 @@
 		};
 
 		mdio: mdio@26200f00 {
-			compatible	= "ti,keystone_mdio", "ti,davinci_mdio";
+			compatible = "ti,keystone_mdio", "ti,davinci_mdio";
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <0x26200f00 0x100>;
 			status = "disabled";
 			clocks = <&clkcpgmac>;
 			clock-names = "fck";
-			bus_freq	= <2500000>;
+			bus_freq = <2500000>;
 		};
 		/include/ "keystone-k2l-netcp.dtsi"
 };
diff --git a/arch/arm/boot/dts/keystone.dtsi b/arch/arm/boot/dts/keystone.dtsi
index fc9fdc857ae8..50789f9e2215 100644
--- a/arch/arm/boot/dts/keystone.dtsi
+++ b/arch/arm/boot/dts/keystone.dtsi
@@ -14,7 +14,7 @@
 	interrupt-parent = <&gic>;
 
 	aliases {
-		serial0	= &uart0;
+		serial0 = &uart0;
 		spi0 = &spi0;
 		spi1 = &spi1;
 		spi2 = &spi2;
@@ -61,11 +61,11 @@
 	};
 
 	psci {
-		compatible	= "arm,psci";
-		method		= "smc";
-		cpu_suspend	= <0x84000001>;
-		cpu_off		= <0x84000002>;
-		cpu_on		= <0x84000003>;
+		compatible = "arm,psci";
+		method = "smc";
+		cpu_suspend = <0x84000001>;
+		cpu_off = <0x84000002>;
+		cpu_on = <0x84000003>;
 	};
 
 	soc0: soc@0 {
@@ -119,7 +119,7 @@
 			reg-shift = <2>;
 			reg-io-width = <4>;
 			reg = <0x02530c00 0x100>;
-			clocks	= <&clkuart0>;
+			clocks = <&clkuart0>;
 			interrupts = <GIC_SPI 277 IRQ_TYPE_EDGE_RISING>;
 		};
 
@@ -129,7 +129,7 @@
 			reg-shift = <2>;
 			reg-io-width = <4>;
 			reg = <0x02531000 0x100>;
-			clocks	= <&clkuart1>;
+			clocks = <&clkuart1>;
 			interrupts = <GIC_SPI 280 IRQ_TYPE_EDGE_RISING>;
 		};
 
@@ -301,7 +301,7 @@
 			clock-names = "pcie";
 			#address-cells = <3>;
 			#size-cells = <2>;
-			reg =  <0x21801000 0x2000>, <0x21800000 0x1000>, <0x02620128 4>;
+			reg = <0x21801000 0x2000>, <0x21800000 0x1000>, <0x02620128 4>;
 			ranges = <0x82000000 0 0x50000000 0x50000000
 				  0 0x10000000>;
 
diff --git a/arch/arm/boot/dts/kirkwood-6192.dtsi b/arch/arm/boot/dts/kirkwood-6192.dtsi
index 396bcba08adb..705c0d7effed 100644
--- a/arch/arm/boot/dts/kirkwood-6192.dtsi
+++ b/arch/arm/boot/dts/kirkwood-6192.dtsi
@@ -26,12 +26,22 @@
 				ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
 					  0x81000000 0 0 0x81000000 0x1 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &intc 9>;
+				interrupt-names = "intx", "error";
+				interrupts = <9>, <44>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie_intc 0>,
+						<0 0 0 2 &pcie_intc 1>,
+						<0 0 0 3 &pcie_intc 2>,
+						<0 0 0 4 &pcie_intc 3>;
 				marvell,pcie-port = <0>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gate_clk 2>;
 				status = "disabled";
+
+				pcie_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 		};
 	};
diff --git a/arch/arm/boot/dts/kirkwood-6281.dtsi b/arch/arm/boot/dts/kirkwood-6281.dtsi
index faa05849a40d..8e311165fd13 100644
--- a/arch/arm/boot/dts/kirkwood-6281.dtsi
+++ b/arch/arm/boot/dts/kirkwood-6281.dtsi
@@ -26,12 +26,22 @@
 				ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
 					  0x81000000 0 0 0x81000000 0x1 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &intc 9>;
+				interrupt-names = "intx", "error";
+				interrupts = <9>, <44>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie_intc 0>,
+						<0 0 0 2 &pcie_intc 1>,
+						<0 0 0 3 &pcie_intc 2>,
+						<0 0 0 4 &pcie_intc 3>;
 				marvell,pcie-port = <0>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gate_clk 2>;
 				status = "disabled";
+
+				pcie_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 		};
 	};
diff --git a/arch/arm/boot/dts/kirkwood-6282.dtsi b/arch/arm/boot/dts/kirkwood-6282.dtsi
index e84c54b77dea..e33723160ce7 100644
--- a/arch/arm/boot/dts/kirkwood-6282.dtsi
+++ b/arch/arm/boot/dts/kirkwood-6282.dtsi
@@ -30,12 +30,22 @@
 				ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
 					  0x81000000 0 0 0x81000000 0x1 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &intc 9>;
+				interrupt-names = "intx", "error";
+				interrupts = <9>, <44>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie0_intc 0>,
+						<0 0 0 2 &pcie0_intc 1>,
+						<0 0 0 3 &pcie0_intc 2>,
+						<0 0 0 4 &pcie0_intc 3>;
 				marvell,pcie-port = <0>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gate_clk 2>;
 				status = "disabled";
+
+				pcie0_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 
 			pcie1: pcie@2,0 {
@@ -48,12 +58,22 @@
 				ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0
 					  0x81000000 0 0 0x81000000 0x2 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &intc 10>;
+				interrupt-names = "intx", "error";
+				interrupts = <10>, <45>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie1_intc 0>,
+						<0 0 0 2 &pcie1_intc 1>,
+						<0 0 0 3 &pcie1_intc 2>,
+						<0 0 0 4 &pcie1_intc 3>;
 				marvell,pcie-port = <1>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gate_clk 18>;
 				status = "disabled";
+
+				pcie1_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 		};
 	};
diff --git a/arch/arm/boot/dts/kirkwood-98dx4122.dtsi b/arch/arm/boot/dts/kirkwood-98dx4122.dtsi
index 299c147298c3..c3469a2fc58a 100644
--- a/arch/arm/boot/dts/kirkwood-98dx4122.dtsi
+++ b/arch/arm/boot/dts/kirkwood-98dx4122.dtsi
@@ -26,12 +26,22 @@
 				ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
 					  0x81000000 0 0 0x81000000 0x1 0 1 0>;
 				bus-range = <0x00 0xff>;
-				interrupt-map-mask = <0 0 0 0>;
-				interrupt-map = <0 0 0 0 &intc 9>;
+				interrupt-names = "intx", "error";
+				interrupts = <9>, <44>;
+				interrupt-map-mask = <0 0 0 7>;
+				interrupt-map = <0 0 0 1 &pcie_intc 0>,
+						<0 0 0 2 &pcie_intc 1>,
+						<0 0 0 3 &pcie_intc 2>,
+						<0 0 0 4 &pcie_intc 3>;
 				marvell,pcie-port = <0>;
 				marvell,pcie-lane = <0>;
 				clocks = <&gate_clk 2>;
 				status = "disabled";
+
+				pcie_intc: interrupt-controller {
+					interrupt-controller;
+					#interrupt-cells = <1>;
+				};
 			};
 		};
 	};
diff --git a/arch/arm/boot/dts/kirkwood-c200-v1.dts b/arch/arm/boot/dts/kirkwood-c200-v1.dts
new file mode 100644
index 000000000000..f59ff7578dfc
--- /dev/null
+++ b/arch/arm/boot/dts/kirkwood-c200-v1.dts
@@ -0,0 +1,310 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Ctera C200 V1 Board Description
+ * Copyright 2021-2022 Pawel Dembicki <paweldembicki@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "kirkwood.dtsi"
+#include "kirkwood-6281.dtsi"
+#include <dt-bindings/leds/common.h>
+
+/ {
+	model = "Ctera C200 V1";
+	compatible = "ctera,c200-v1", "marvell,kirkwood-88f6281", "marvell,kirkwood";
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+		stdout-path = &uart0;
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x20000000>;
+	};
+
+	keys {
+		compatible = "gpio-keys";
+		pinctrl-0 = <&pmx_buttons>;
+		pinctrl-names = "default";
+
+		power {
+			label = "Power Button";
+			linux,code = <KEY_POWER>;
+			gpios = <&gpio1 16 GPIO_ACTIVE_HIGH>;
+		};
+
+		reset {
+			label = "Reset Button";
+			linux,code = <KEY_RESTART>;
+			gpios = <&gpio1 17 GPIO_ACTIVE_LOW>;
+		};
+
+		usb1 {
+			label = "USB1 Button";
+			linux,code = <BTN_0>;
+			gpios = <&gpio0 28 GPIO_ACTIVE_LOW>;
+		};
+
+		usb2 {
+			label = "USB2 Button";
+			linux,code = <BTN_1>;
+			gpios = <&gpio0 29 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	gpio-poweroff {
+		compatible = "gpio-poweroff";
+		pinctrl-0 = <&pmx_poweroff>;
+		pinctrl-names = "default";
+		gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-0 = <&pmx_leds>;
+		pinctrl-names = "default";
+
+		led-0 {
+			function = LED_FUNCTION_DISK;
+			function-enumerator = <2>;
+			color = <LED_COLOR_ID_RED>;
+			gpios = <&gpio0 14 GPIO_ACTIVE_LOW>;
+		};
+
+		led-1 {
+			function = LED_FUNCTION_DISK;
+			function-enumerator = <1>;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&gpio0 15 GPIO_ACTIVE_LOW>;
+		};
+
+		led-2 {
+			function = LED_FUNCTION_DISK;
+			function-enumerator = <2>;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&gpio0 16 GPIO_ACTIVE_LOW>;
+		};
+
+		led-3 {
+			function = LED_FUNCTION_DISK;
+			function-enumerator = <1>;
+			color = <LED_COLOR_ID_RED>;
+			gpios = <&gpio0 17 GPIO_ACTIVE_LOW>;
+		};
+
+		led-4 {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_RED>;
+			gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
+		};
+
+		led-5 {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&gpio1 7 GPIO_ACTIVE_LOW>;
+		};
+
+		led-6 {
+			function = LED_FUNCTION_INDICATOR;
+			color = <LED_COLOR_ID_BLUE>;
+			gpios = <&gpio1 8 GPIO_ACTIVE_LOW>;
+		};
+
+		led-7 {
+			function = LED_FUNCTION_DISK_ERR;
+			color = <LED_COLOR_ID_RED>;
+			gpios = <&gpio1 10 GPIO_ACTIVE_LOW>;
+		};
+
+		led-8 {
+			function = LED_FUNCTION_DISK_ERR;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&gpio1 11 GPIO_ACTIVE_LOW>;
+		};
+
+		led-9 {
+			function = LED_FUNCTION_USB;
+			function-enumerator = <1>;
+			color = <LED_COLOR_ID_RED>;
+			gpios = <&gpio1 12 GPIO_ACTIVE_LOW>;
+		};
+
+		led-10 {
+			function = LED_FUNCTION_USB;
+			function-enumerator = <1>;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&gpio1 13 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "usbport";
+			trigger-sources = <&hub_port2>;
+		};
+
+		led-11 {
+			function = LED_FUNCTION_USB;
+			function-enumerator = <2>;
+			color = <LED_COLOR_ID_RED>;
+			gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
+		};
+
+		led-12 {
+			function = LED_FUNCTION_USB;
+			function-enumerator = <2>;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "usbport";
+			trigger-sources = <&hub_port1>;
+		};
+	};
+};
+
+&eth0 {
+	status = "okay";
+};
+
+&eth0port {
+	phy-handle = <&ethphy9>;
+};
+
+&i2c0 {
+	status = "okay";
+
+	rtc@30 {
+		compatible = "s35390a";
+		reg = <0x30>;
+	};
+
+	lm63@4c {
+		compatible = "national,lm63";
+		reg = <0x4c>;
+	};
+};
+
+&mdio {
+	status = "okay";
+
+	ethphy9: ethernet-phy@9 {
+		reg = <9>;
+	};
+};
+
+&nand {
+	status = "okay";
+	chip-delay = <40>;
+
+	partition@0 {
+		label = "uboot";
+		reg = <0x0000000 0x200000>;
+	};
+
+	partition@200000 {
+		label = "certificate";
+		reg = <0x0200000 0x100000>;
+	};
+
+	partition@300000 {
+		label = "preset_cfg";
+		reg = <0x0300000 0x100000>;
+	};
+
+	partition@400000 {
+		label = "dev_params";
+		reg = <0x0400000 0x100000>;
+	};
+
+	partition@500000 {
+		label = "active_bank";
+		reg = <0x0500000 0x0100000>;
+	};
+
+	partition@600000 {
+		label = "magic";
+		reg = <0x0600000 0x0100000>;
+	};
+
+	partition@700000 {
+		label = "bank1";
+		reg = <0x0700000 0x2800000>;
+	};
+
+	partition@2f00000 {
+		label = "bank2";
+		reg = <0x2f00000 0x2800000>;
+	};
+
+	/* 0x5700000-0x5a00000 undefined in vendor firmware */
+
+	partition@5a00000 {
+		label = "reserved";
+		reg = <0x5a00000 0x2000000>;
+	};
+
+	partition@7a00000 {
+		label = "rootfs";
+		reg = <0x7a00000 0x8600000>;
+	};
+};
+
+&pinctrl {
+	/* Buzzer gpios are connected to two pins of buzzer.
+	 * This buzzer require a modulated signal from gpio.
+	 * Leave it as is due lack of proper driver.
+	 */
+	pmx_buzzer: pmx-buzzer {
+		marvell,pins = "mpp12", "mpp13";
+		marvell,function = "gpio";
+	};
+
+	pmx_leds: pmx-leds {
+		marvell,pins = "mpp14", "mpp15", "mpp16", "mpp17", "mpp38",
+			       "mpp39", "mpp40", "mpp42", "mpp43", "mpp44",
+			       "mpp45", "mpp46", "mpp47";
+		marvell,function = "gpio";
+	};
+
+	pmx_buttons: pmx-buttons {
+		marvell,pins = "mpp28", "mpp29", "mpp48", "mpp49";
+		marvell,function = "gpio";
+	};
+
+	pmx_poweroff: pmx-poweroff {
+		marvell,pins = "mpp34";
+		marvell,function = "gpio";
+	};
+};
+
+&rtc {
+	status = "disabled";
+};
+
+&sata {
+	status = "okay";
+	nr-ports = <2>;
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&usb0 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	port@1 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <1>;
+		#trigger-source-cells = <0>;
+
+		hub_port1: port@1 {
+			reg = <1>;
+			#trigger-source-cells = <0>;
+		};
+
+		hub_port2: port@2 {
+			reg = <2>;
+			#trigger-source-cells = <0>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/kirkwood-dir665.dts b/arch/arm/boot/dts/kirkwood-dir665.dts
index b3ad3f607d31..c32300611d2c 100644
--- a/arch/arm/boot/dts/kirkwood-dir665.dts
+++ b/arch/arm/boot/dts/kirkwood-dir665.dts
@@ -78,7 +78,7 @@
 
 		spi@10600 {
 			status = "okay";
-			m25p80@0 {
+			flash@0 {
 				#address-cells = <1>;
 				#size-cells = <1>;
 				compatible = "mxicy,mx25l12805d", "jedec,spi-nor";
diff --git a/arch/arm/boot/dts/kirkwood-lsxl.dtsi b/arch/arm/boot/dts/kirkwood-lsxl.dtsi
index 7b151acb9984..88b70ba1c8fe 100644
--- a/arch/arm/boot/dts/kirkwood-lsxl.dtsi
+++ b/arch/arm/boot/dts/kirkwood-lsxl.dtsi
@@ -10,6 +10,11 @@
 
 	ocp@f1000000 {
 		pinctrl: pin-controller@10000 {
+			/* Non-default UART pins */
+			pmx_uart0: pmx-uart0 {
+				marvell,pins = "mpp4", "mpp5";
+			};
+
 			pmx_power_hdd: pmx-power-hdd {
 				marvell,pins = "mpp10";
 				marvell,function = "gpo";
@@ -213,22 +218,11 @@
 &mdio {
 	status = "okay";
 
-	ethphy0: ethernet-phy@0 {
-		reg = <0>;
-	};
-
 	ethphy1: ethernet-phy@8 {
 		reg = <8>;
 	};
 };
 
-&eth0 {
-	status = "okay";
-	ethernet0-port@0 {
-		phy-handle = <&ethphy0>;
-	};
-};
-
 &eth1 {
 	status = "okay";
 	ethernet1-port@0 {
diff --git a/arch/arm/boot/dts/kirkwood-synology.dtsi b/arch/arm/boot/dts/kirkwood-synology.dtsi
index 217bd374e52b..8f6c387d3a8b 100644
--- a/arch/arm/boot/dts/kirkwood-synology.dtsi
+++ b/arch/arm/boot/dts/kirkwood-synology.dtsi
@@ -198,7 +198,7 @@
 		spi@10600 {
 			status = "okay";
 
-			m25p80@0 {
+			flash@0 {
 				#address-cells = <1>;
 				#size-cells = <1>;
 				compatible = "st,m25p80", "jedec,spi-nor";
diff --git a/arch/arm/boot/dts/lan966x-kontron-kswitch-d10-mmt-6g-2gs.dts b/arch/arm/boot/dts/lan966x-kontron-kswitch-d10-mmt-6g-2gs.dts
new file mode 100644
index 000000000000..0f555eb45bda
--- /dev/null
+++ b/arch/arm/boot/dts/lan966x-kontron-kswitch-d10-mmt-6g-2gs.dts
@@ -0,0 +1,94 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device Tree file for the Kontron KSwitch D10 MMT 6G-2GS
+ */
+
+/dts-v1/;
+#include "lan966x-kontron-kswitch-d10-mmt.dtsi"
+
+/ {
+	model = "Kontron KSwitch D10 MMT 6G-2GS";
+	compatible = "kontron,kswitch-d10-mmt-6g-2gs", "kontron,s1921",
+		     "microchip,lan9668", "microchip,lan966";
+
+	aliases {
+		i2c0 = &i2c4;
+		i2c1 = &i2c1;
+	};
+
+	sfp0: sfp0 {
+		compatible = "sff,sfp";
+		i2c-bus = <&i2c4>;
+		los-gpios = <&sgpio_in 1 0 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&sgpio_in 1 1 GPIO_ACTIVE_LOW>;
+		maximum-power-milliwatt = <2500>;
+		tx-disable-gpios = <&sgpio_out 3 0 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios = <&sgpio_in 0 2 GPIO_ACTIVE_HIGH>;
+		rate-select0-gpios = <&sgpio_out 2 0 GPIO_ACTIVE_HIGH>;
+		rate-select1-gpios = <&sgpio_out 2 1 GPIO_ACTIVE_HIGH>;
+	};
+
+	sfp1: sfp1 {
+		compatible = "sff,sfp";
+		i2c-bus = <&i2c1>;
+		los-gpios = <&sgpio_in 1 2 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&sgpio_in 1 3 GPIO_ACTIVE_LOW>;
+		maximum-power-milliwatt = <2500>;
+		tx-disable-gpios = <&sgpio_out 3 1 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios = <&sgpio_in 0 3 GPIO_ACTIVE_HIGH>;
+		rate-select0-gpios = <&sgpio_out 2 2 GPIO_ACTIVE_HIGH>;
+		rate-select1-gpios = <&sgpio_out 2 3 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&flx1 {
+	atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_TWI>;
+	status = "okay";
+
+	i2c1: i2c@600 {
+		pinctrl-0 = <&fc1_c_pins>;
+		pinctrl-names = "default";
+		status = "okay";
+	};
+};
+
+&flx4 {
+	atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_TWI>;
+	status = "okay";
+
+	i2c4: i2c@600 {
+		pinctrl-0 = <&fc4_b_pins>;
+		pinctrl-names = "default";
+		status = "okay";
+	};
+};
+
+&gpio {
+	fc1_c_pins: fc1-c-i2c-pins {
+		/* SCL, SDA */
+		pins = "GPIO_47", "GPIO_48";
+		function = "fc1_c";
+	};
+
+	fc4_b_pins: fc4-b-i2c-pins {
+		/* SCL, SDA */
+		pins = "GPIO_57", "GPIO_58";
+		function = "fc4_b";
+	};
+};
+
+&port2 {
+	phys = <&serdes 2 SERDES6G(0)>;
+	sfp = <&sfp0>;
+	managed = "in-band-status";
+	phy-mode = "sgmii";
+	status = "okay";
+};
+
+&port3 {
+	phys = <&serdes 3 SERDES6G(1)>;
+	sfp = <&sfp1>;
+	managed = "in-band-status";
+	phy-mode = "sgmii";
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/lan966x-kontron-kswitch-d10-mmt-8g.dts b/arch/arm/boot/dts/lan966x-kontron-kswitch-d10-mmt-8g.dts
new file mode 100644
index 000000000000..5feef9a59a79
--- /dev/null
+++ b/arch/arm/boot/dts/lan966x-kontron-kswitch-d10-mmt-8g.dts
@@ -0,0 +1,39 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device Tree file for the Kontron KSwitch D10 MMT 8G
+ */
+
+/dts-v1/;
+#include "lan966x-kontron-kswitch-d10-mmt.dtsi"
+
+/ {
+	model = "Kontron KSwitch D10 MMT 8G";
+	compatible = "kontron,kswitch-d10-mmt-8g", "kontron,s1921",
+		     "microchip,lan9668", "microchip,lan966";
+};
+
+&mdio0 {
+	phy2: ethernet-phy@3 {
+		reg = <3>;
+	};
+
+	phy3: ethernet-phy@4 {
+		reg = <4>;
+	};
+};
+
+&port2 {
+	phys = <&serdes 2 SERDES6G(0)>;
+	phy-handle = <&phy2>;
+	phy-mode = "sgmii";
+	managed = "in-band-status";
+	status = "okay";
+};
+
+&port3 {
+	phys = <&serdes 3 SERDES6G(1)>;
+	phy-handle = <&phy3>;
+	phy-mode = "sgmii";
+	managed = "in-band-status";
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/lan966x-kontron-kswitch-d10-mmt.dtsi b/arch/arm/boot/dts/lan966x-kontron-kswitch-d10-mmt.dtsi
new file mode 100644
index 000000000000..0097e72e3fb2
--- /dev/null
+++ b/arch/arm/boot/dts/lan966x-kontron-kswitch-d10-mmt.dtsi
@@ -0,0 +1,203 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Common part of the device tree for the Kontron KSwitch D10 MMT
+ */
+
+/dts-v1/;
+#include "lan966x.dtsi"
+#include "dt-bindings/phy/phy-lan966x-serdes.h"
+
+/ {
+	aliases {
+		serial0 = &usart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-restart {
+		compatible = "gpio-restart";
+		gpios = <&gpio 56 GPIO_ACTIVE_LOW>;
+		priority = <200>;
+	};
+};
+
+&flx0 {
+	atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_USART>;
+	status = "okay";
+
+	usart0: serial@200 {
+		pinctrl-0 = <&usart0_pins>;
+		pinctrl-names = "default";
+		status = "okay";
+	};
+};
+
+&flx3 {
+	atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_SPI>;
+	status = "okay";
+
+	spi3: spi@400 {
+		pinctrl-0 = <&fc3_b_pins>;
+		pinctrl-names = "default";
+		status = "okay";
+		cs-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&gpio {
+	fc3_b_pins: fc3-b-pins {
+		/* SCK, MISO, MOSI */
+		pins = "GPIO_51", "GPIO_52", "GPIO_53";
+		function = "fc3_b";
+	};
+
+	miim_c_pins: miim-c-pins {
+		/* MDC, MDIO */
+		pins = "GPIO_59", "GPIO_60";
+		function = "miim_c";
+	};
+
+	sgpio_a_pins: sgpio-a-pins {
+		/* SCK, D0, D1 */
+		pins = "GPIO_32", "GPIO_33", "GPIO_34";
+		function = "sgpio_a";
+	};
+
+	sgpio_b_pins: sgpio-b-pins {
+		/* LD */
+		pins = "GPIO_64";
+		function = "sgpio_b";
+	};
+
+	usart0_pins: usart0-pins {
+		/* RXD, TXD */
+		pins = "GPIO_25", "GPIO_26";
+		function = "fc0_b";
+	};
+
+	usbs_a_pins: usbs-a-pins {
+		/* VBUS_DET */
+		pins = "GPIO_66";
+		function = "gpio";
+	};
+};
+
+&mdio0 {
+	pinctrl-0 = <&miim_c_pins>;
+	pinctrl-names = "default";
+	reset-gpios = <&gpio 29 GPIO_ACTIVE_LOW>;
+	clock-frequency = <2500000>;
+	status = "okay";
+
+	phy4: ethernet-phy@5 {
+		reg = <5>;
+		coma-mode-gpios = <&gpio 37 GPIO_OPEN_DRAIN>;
+	};
+
+	phy5: ethernet-phy@6 {
+		reg = <6>;
+		coma-mode-gpios = <&gpio 37 GPIO_OPEN_DRAIN>;
+	};
+
+	phy6: ethernet-phy@7 {
+		reg = <7>;
+		coma-mode-gpios = <&gpio 37 GPIO_OPEN_DRAIN>;
+	};
+
+	phy7: ethernet-phy@8 {
+		reg = <8>;
+		coma-mode-gpios = <&gpio 37 GPIO_OPEN_DRAIN>;
+	};
+};
+
+&mdio1 {
+	status = "okay";
+};
+
+&phy0 {
+	status = "okay";
+};
+
+&phy1 {
+	status = "okay";
+};
+
+&port0 {
+	phys = <&serdes 0 CU(0)>;
+	phy-handle = <&phy0>;
+	phy-mode = "gmii";
+	status = "okay";
+};
+
+&port1 {
+	phys = <&serdes 1 CU(1)>;
+	phy-handle = <&phy1>;
+	phy-mode = "gmii";
+	status = "okay";
+};
+
+&port4 {
+	phys = <&serdes 4 SERDES6G(2)>;
+	phy-handle = <&phy4>;
+	phy-mode = "qsgmii";
+	status = "okay";
+};
+
+&port5 {
+	phys = <&serdes 5 SERDES6G(2)>;
+	phy-handle = <&phy5>;
+	phy-mode = "qsgmii";
+	status = "okay";
+};
+
+&port6 {
+	phys = <&serdes 6 SERDES6G(2)>;
+	phy-handle = <&phy6>;
+	phy-mode = "qsgmii";
+	status = "okay";
+};
+
+&port7 {
+	phys = <&serdes 7 SERDES6G(2)>;
+	phy-handle = <&phy7>;
+	phy-mode = "qsgmii";
+	status = "okay";
+};
+
+&serdes {
+	status = "okay";
+};
+
+&sgpio {
+	pinctrl-0 = <&sgpio_a_pins>, <&sgpio_b_pins>;
+	pinctrl-names = "default";
+	bus-frequency = <8000000>;
+	/* arbitrary range because all GPIOs are in software mode */
+	microchip,sgpio-port-ranges = <0 11>;
+	status = "okay";
+
+	sgpio_in: gpio@0 {
+		ngpios = <128>;
+	};
+
+	sgpio_out: gpio@1 {
+		ngpios = <128>;
+	};
+};
+
+&switch {
+	status = "okay";
+};
+
+&udc {
+	pinctrl-0 = <&usbs_a_pins>;
+	pinctrl-names = "default";
+	atmel,vbus-gpio = <&gpio 66 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+};
+
+&watchdog {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/lan966x-pcb8290.dts b/arch/arm/boot/dts/lan966x-pcb8290.dts
new file mode 100644
index 000000000000..77187f59f04d
--- /dev/null
+++ b/arch/arm/boot/dts/lan966x-pcb8290.dts
@@ -0,0 +1,179 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * lan966x-pcb8290.dts - Device Tree file for LAN966X-PCB8290 board
+ *
+ * Copyright (C) 2022 Microchip Technology Inc. and its subsidiaries
+ *
+ * Author: Horatiu Vultur <horatiu.vultur@microchip.com>
+ */
+/dts-v1/;
+#include "lan966x.dtsi"
+#include "dt-bindings/phy/phy-lan966x-serdes.h"
+
+/ {
+	model = "Microchip EVB LAN9668";
+	compatible = "microchip,lan9668-pcb8290", "microchip,lan9668", "microchip,lan966";
+
+	gpio-restart {
+		compatible = "gpio-restart";
+		gpios = <&gpio 56 GPIO_ACTIVE_LOW>;
+		priority = <200>;
+	};
+};
+
+&aes {
+	status = "disabled"; /* Reserved by secure OS */
+};
+
+&gpio {
+	miim_a_pins: mdio-pins {
+		/* MDC, MDIO */
+		pins =  "GPIO_28", "GPIO_29";
+		function = "miim_a";
+	};
+
+	pps_out_pins: pps-out-pins {
+		/* 1pps output */
+		pins = "GPIO_38";
+		function = "ptpsync_3";
+	};
+
+	ptp_ext_pins: ptp-ext-pins {
+		/* 1pps input */
+		pins = "GPIO_35";
+		function = "ptpsync_0";
+	};
+
+	udc_pins: ucd-pins {
+		/* VBUS_DET B */
+		pins = "GPIO_8";
+		function = "usb_slave_b";
+	};
+};
+
+&mdio0 {
+	pinctrl-0 = <&miim_a_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	ext_phy0: ethernet-phy@7 {
+		reg = <7>;
+		coma-mode-gpios = <&gpio 60 GPIO_OPEN_DRAIN>;
+	};
+
+	ext_phy1: ethernet-phy@8 {
+		reg = <8>;
+		coma-mode-gpios = <&gpio 60 GPIO_OPEN_DRAIN>;
+	};
+
+	ext_phy2: ethernet-phy@9 {
+		reg = <9>;
+		coma-mode-gpios = <&gpio 60 GPIO_OPEN_DRAIN>;
+	};
+
+	ext_phy3: ethernet-phy@10 {
+		reg = <10>;
+		coma-mode-gpios = <&gpio 60 GPIO_OPEN_DRAIN>;
+	};
+
+	ext_phy4: ethernet-phy@15 {
+		reg = <15>;
+		coma-mode-gpios = <&gpio 60 GPIO_OPEN_DRAIN>;
+	};
+
+	ext_phy5: ethernet-phy@16 {
+		reg = <16>;
+		coma-mode-gpios = <&gpio 60 GPIO_OPEN_DRAIN>;
+	};
+
+	ext_phy6: ethernet-phy@17 {
+		reg = <17>;
+		coma-mode-gpios = <&gpio 60 GPIO_OPEN_DRAIN>;
+	};
+
+	ext_phy7: ethernet-phy@18 {
+		reg = <18>;
+		coma-mode-gpios = <&gpio 60 GPIO_OPEN_DRAIN>;
+	};
+};
+
+&port0 {
+	reg = <2>;
+	phy-handle = <&ext_phy2>;
+	phy-mode = "qsgmii";
+	phys = <&serdes 0 SERDES6G(1)>;
+	status = "okay";
+};
+
+&port1 {
+	reg = <3>;
+	phy-handle = <&ext_phy3>;
+	phy-mode = "qsgmii";
+	phys = <&serdes 1 SERDES6G(1)>;
+	status = "okay";
+};
+
+&port2 {
+	reg = <0>;
+	phy-handle = <&ext_phy0>;
+	phy-mode = "qsgmii";
+	phys = <&serdes 2 SERDES6G(1)>;
+	status = "okay";
+};
+
+&port3 {
+	reg = <1>;
+	phy-handle = <&ext_phy1>;
+	phy-mode = "qsgmii";
+	phys = <&serdes 3 SERDES6G(1)>;
+	status = "okay";
+};
+
+&port4 {
+	reg = <6>;
+	phy-handle = <&ext_phy6>;
+	phy-mode = "qsgmii";
+	phys = <&serdes 4 SERDES6G(2)>;
+	status = "okay";
+};
+
+&port5 {
+	reg = <7>;
+	phy-handle = <&ext_phy7>;
+	phy-mode = "qsgmii";
+	phys = <&serdes 5 SERDES6G(2)>;
+	status = "okay";
+};
+
+&port6 {
+	reg = <4>;
+	phy-handle = <&ext_phy4>;
+	phy-mode = "qsgmii";
+	phys = <&serdes 6 SERDES6G(2)>;
+	status = "okay";
+};
+
+&port7 {
+	reg = <5>;
+	phy-handle = <&ext_phy5>;
+	phy-mode = "qsgmii";
+	phys = <&serdes 7 SERDES6G(2)>;
+	status = "okay";
+};
+
+&serdes {
+	status = "okay";
+};
+
+&switch {
+	pinctrl-0 = <&pps_out_pins>, <&ptp_ext_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&udc {
+	pinctrl-0 = <&udc_pins>;
+	pinctrl-names = "default";
+	atmel,vbus-gpio = <&gpio 8 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/lan966x-pcb8291.dts b/arch/arm/boot/dts/lan966x-pcb8291.dts
new file mode 100644
index 000000000000..f4f054cdf2a8
--- /dev/null
+++ b/arch/arm/boot/dts/lan966x-pcb8291.dts
@@ -0,0 +1,127 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * lan966x_pcb8291.dts - Device Tree file for PCB8291
+ */
+/dts-v1/;
+#include "lan966x.dtsi"
+#include "dt-bindings/phy/phy-lan966x-serdes.h"
+
+/ {
+	model = "Microchip EVB - LAN9662";
+	compatible = "microchip,lan9662-pcb8291", "microchip,lan9662", "microchip,lan966";
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	aliases {
+		serial0 = &usart3;
+	};
+
+	gpio-restart {
+		compatible = "gpio-restart";
+		gpios = <&gpio 56 GPIO_ACTIVE_LOW>;
+		priority = <200>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-s0-blue {
+			label = "s0:blue";
+			gpios = <&sgpio_out 2 0 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led-s0-green {
+			label = "s0:green";
+			gpios = <&sgpio_out 2 1 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led-s1-blue {
+			label = "s1:blue";
+			gpios = <&sgpio_out 3 0 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led-s1-green {
+			label = "s1:green";
+			gpios = <&sgpio_out 3 1 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+	};
+};
+
+&aes {
+	status = "disabled"; /* Reserved by secure OS */
+};
+
+&gpio {
+	fc3_b_pins: fc3-b-pins {
+		/* RX, TX */
+		pins = "GPIO_52", "GPIO_53";
+		function = "fc3_b";
+	};
+
+	can0_b_pins:  can0-b-pins {
+		/* RX, TX */
+		pins = "GPIO_35", "GPIO_36";
+		function = "can0_b";
+	};
+};
+
+&can0 {
+	pinctrl-0 = <&can0_b_pins>;
+	pinctrl-names = "default";
+	status = "disabled"; /* Conflict with switch */
+};
+
+&flx3 {
+	atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_USART>;
+	status = "okay";
+
+	usart3: serial@200 {
+		pinctrl-0 = <&fc3_b_pins>;
+		pinctrl-names = "default";
+		status = "okay";
+	};
+};
+
+&mdio1 {
+	status = "okay";
+};
+
+&phy0 {
+	status = "okay";
+};
+
+&phy1 {
+	status = "okay";
+};
+
+&port0 {
+	phy-handle = <&phy0>;
+	phy-mode = "gmii";
+	phys = <&serdes 0 CU(0)>;
+	status = "okay";
+};
+
+&port1 {
+	phy-handle = <&phy1>;
+	phy-mode = "gmii";
+	phys = <&serdes 1 CU(1)>;
+	status = "okay";
+};
+
+&serdes {
+	status = "okay";
+};
+
+&switch {
+	status = "okay";
+};
+
+&watchdog {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/lan966x-pcb8309.dts b/arch/arm/boot/dts/lan966x-pcb8309.dts
new file mode 100644
index 000000000000..c436cd20d4b4
--- /dev/null
+++ b/arch/arm/boot/dts/lan966x-pcb8309.dts
@@ -0,0 +1,216 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * lan966x_pcb8309.dts - Device Tree file for PCB8309
+ */
+/dts-v1/;
+#include "lan966x.dtsi"
+#include "dt-bindings/phy/phy-lan966x-serdes.h"
+
+/ {
+	model = "Microchip EVB - LAN9662";
+	compatible = "microchip,lan9662-pcb8309", "microchip,lan9662", "microchip,lan966";
+
+	aliases {
+		serial0 = &usart3;
+		i2c102 = &i2c102;
+		i2c103 = &i2c103;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-restart {
+		compatible = "gpio-restart";
+		gpios = <&gpio 56 GPIO_ACTIVE_LOW>;
+		priority = <200>;
+	};
+
+	i2c-mux {
+		compatible = "i2c-mux";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		mux-controls = <&mux>;
+		i2c-parent = <&i2c4>;
+
+		i2c102: i2c-sfp@1 {
+			reg = <1>;
+		};
+
+		i2c103: i2c-sfp@2 {
+			reg = <2>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-s0-green {
+			label = "s0:green";
+			gpios = <&sgpio_out 2 0 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led-s0-red {
+			label = "s0:red";
+			gpios = <&sgpio_out 2 1 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led-s1-green {
+			label = "s1:green";
+			gpios = <&sgpio_out 3 0 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led-s1-red {
+			label = "s1:red";
+			gpios = <&sgpio_out 3 1 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+	};
+
+	mux: mux-controller {
+		compatible = "gpio-mux";
+		#mux-control-cells = <0>;
+
+		mux-gpios = <&sgpio_out 11 0 GPIO_ACTIVE_HIGH>, /* p11b0 */
+			    <&sgpio_out 11 1 GPIO_ACTIVE_HIGH>; /* p11b1 */
+	};
+
+	sfp2: sfp2 {
+		compatible = "sff,sfp";
+		i2c-bus = <&i2c102>;
+		tx-disable-gpios = <&sgpio_out 10 0 GPIO_ACTIVE_LOW>;
+		los-gpios = <&sgpio_in  2 0 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&sgpio_in  2 1 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios = <&sgpio_in  1 0 GPIO_ACTIVE_HIGH>;
+	};
+
+	sfp3: sfp3 {
+		compatible = "sff,sfp";
+		i2c-bus = <&i2c103>;
+		tx-disable-gpios = <&sgpio_out 10 1 GPIO_ACTIVE_LOW>;
+		los-gpios = <&sgpio_in  3 0 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&sgpio_in  3 1 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios = <&sgpio_in  1 1 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&aes {
+	status = "disabled"; /* Reserved by secure OS */
+};
+
+&flx3 {
+	atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_USART>;
+	status = "okay";
+
+	usart3: serial@200 {
+		pinctrl-0 = <&fc3_b_pins>;
+		pinctrl-names = "default";
+		status = "okay";
+	};
+};
+
+&flx4 {
+	atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_TWI>;
+	status = "okay";
+
+	i2c4: i2c@600 {
+		compatible = "microchip,sam9x60-i2c";
+		reg = <0x600 0x200>;
+		interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&nic_clk>;
+		pinctrl-0 = <&fc4_b_pins>;
+		pinctrl-names = "default";
+		i2c-analog-filter;
+		i2c-digital-filter;
+		i2c-digital-filter-width-ns = <35>;
+		i2c-sda-hold-time-ns = <1500>;
+		status = "okay";
+	};
+};
+
+&gpio {
+	fc3_b_pins: fc3-b-pins {
+		/* RXD, TXD */
+		pins = "GPIO_52", "GPIO_53";
+		function = "fc3_b";
+	};
+
+	fc4_b_pins: fc4-b-pins {
+		/* SCL, SDA */
+		pins = "GPIO_57", "GPIO_58";
+		function = "fc4_b";
+	};
+
+	sgpio_a_pins: sgpio-a-pins {
+		/* SCK, D0, D1, LD */
+		pins = "GPIO_32", "GPIO_33", "GPIO_34", "GPIO_35";
+		function = "sgpio_a";
+	};
+};
+
+&mdio1 {
+	status = "okay";
+};
+
+&phy0 {
+	status = "okay";
+};
+
+&phy1 {
+	status = "okay";
+};
+
+&port0 {
+	phy-handle = <&phy0>;
+	phy-mode = "gmii";
+	phys = <&serdes 0 CU(0)>;
+	status = "okay";
+};
+
+&port1 {
+	phy-handle = <&phy1>;
+	phy-mode = "gmii";
+	phys = <&serdes 1 CU(1)>;
+	status = "okay";
+};
+
+&port2 {
+	sfp = <&sfp2>;
+	managed = "in-band-status";
+	phy-mode = "sgmii";
+	phys = <&serdes 2 SERDES6G(0)>;
+	status = "okay";
+};
+
+&port3 {
+	sfp = <&sfp3>;
+	managed = "in-band-status";
+	phy-mode = "sgmii";
+	phys = <&serdes 3 SERDES6G(1)>;
+	status = "okay";
+};
+
+&serdes {
+	status = "okay";
+};
+
+&sgpio {
+	pinctrl-0 = <&sgpio_a_pins>;
+	pinctrl-names = "default";
+	microchip,sgpio-port-ranges = <0 3>, <8 11>;
+	status = "okay";
+
+	gpio@0 {
+		ngpios = <64>;
+	};
+	gpio@1 {
+		ngpios = <64>;
+	};
+};
+
+&switch {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/lan966x.dtsi b/arch/arm/boot/dts/lan966x.dtsi
new file mode 100644
index 000000000000..0bf818713422
--- /dev/null
+++ b/arch/arm/boot/dts/lan966x.dtsi
@@ -0,0 +1,610 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * lan966x.dtsi - Device Tree Include file for Microchip LAN966 family SoC
+ *
+ * Copyright (C) 2021 Microchip Technology, Inc. and its subsidiaries
+ *
+ * Author: Kavyasree Kotagiri <kavyasree.kotagiri@microchip.com>
+ *
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/mfd/atmel-flexcom.h>
+#include <dt-bindings/dma/at91.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/clock/microchip,lan966x.h>
+
+/ {
+	model = "Microchip LAN966 family SoC";
+	compatible = "microchip,lan966";
+	interrupt-parent = <&gic>;
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			clock-frequency = <600000000>;
+			reg = <0x0>;
+		};
+	};
+
+	clocks {
+		sys_clk: sys_clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <165625000>;
+		};
+
+		cpu_clk: cpu_clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <600000000>;
+		};
+
+		ddr_clk: ddr_clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <300000000>;
+		};
+
+		nic_clk: nic_clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <200000000>;
+		};
+	};
+
+	clks: clock-controller@e00c00a8 {
+		compatible = "microchip,lan966x-gck";
+		#clock-cells = <1>;
+		clocks = <&cpu_clk>, <&ddr_clk>, <&sys_clk>;
+		clock-names = "cpu", "ddr", "sys";
+		reg = <0xe00c00a8 0x38>, <0xe00c02cc 0x4>;
+	};
+
+	timer {
+		compatible = "arm,armv7-timer";
+		interrupt-parent = <&gic>;
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>;
+		clock-frequency = <37500000>;
+	};
+
+	soc {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		udc: usb@200000 {
+			compatible = "microchip,lan9662-udc",
+				     "atmel,sama5d3-udc";
+			reg = <0x00200000 0x80000>,
+			      <0xe0808000 0x400>;
+			interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clks GCK_GATE_UDPHS>, <&nic_clk>;
+			clock-names = "pclk", "hclk";
+			status = "disabled";
+		};
+
+		switch: switch@e0000000 {
+			compatible = "microchip,lan966x-switch";
+			reg = <0xe0000000 0x0100000>,
+			      <0xe2000000 0x0800000>;
+			reg-names = "cpu", "gcb";
+			interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "xtr", "fdma", "ana", "ptp",
+					  "ptp-ext";
+			resets = <&reset 0>;
+			reset-names = "switch";
+			status = "disabled";
+
+			ethernet-ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port0: port@0 {
+					reg = <0>;
+					status = "disabled";
+				};
+
+				port1: port@1 {
+					reg = <1>;
+					status = "disabled";
+				};
+
+				port2: port@2 {
+					reg = <2>;
+					status = "disabled";
+				};
+
+				port3: port@3 {
+					reg = <3>;
+					status = "disabled";
+				};
+
+				port4: port@4 {
+					reg = <4>;
+					status = "disabled";
+				};
+
+				port5: port@5 {
+					reg = <5>;
+					status = "disabled";
+				};
+
+				port6: port@6 {
+					reg = <6>;
+					status = "disabled";
+				};
+
+				port7: port@7 {
+					reg = <7>;
+					status = "disabled";
+				};
+			};
+		};
+
+		flx0: flexcom@e0040000 {
+			compatible = "atmel,sama5d2-flexcom";
+			reg = <0xe0040000 0x100>;
+			clocks = <&clks GCK_ID_FLEXCOM0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0xe0040000 0x800>;
+			status = "disabled";
+
+			usart0: serial@200 {
+				compatible = "atmel,at91sam9260-usart";
+				reg = <0x200 0x200>;
+				interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dma0 AT91_XDMAC_DT_PERID(3)>,
+				       <&dma0 AT91_XDMAC_DT_PERID(2)>;
+				dma-names = "tx", "rx";
+				clocks = <&nic_clk>;
+				clock-names = "usart";
+				atmel,fifo-size = <32>;
+				status = "disabled";
+			};
+
+			spi0: spi@400 {
+				compatible = "atmel,at91rm9200-spi";
+				reg = <0x400 0x200>;
+				interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dma0 AT91_XDMAC_DT_PERID(3)>,
+				       <&dma0 AT91_XDMAC_DT_PERID(2)>;
+				dma-names = "tx", "rx";
+				clocks = <&nic_clk>;
+				clock-names = "spi_clk";
+				atmel,fifo-size = <32>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			i2c0: i2c@600 {
+				compatible = "microchip,sam9x60-i2c";
+				reg = <0x600 0x200>;
+				interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dma0 AT91_XDMAC_DT_PERID(3)>,
+				       <&dma0 AT91_XDMAC_DT_PERID(2)>;
+				dma-names = "tx", "rx";
+				clocks = <&nic_clk>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+		};
+
+		flx1: flexcom@e0044000 {
+			compatible = "atmel,sama5d2-flexcom";
+			reg = <0xe0044000 0x100>;
+			clocks = <&clks GCK_ID_FLEXCOM1>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0xe0044000 0x800>;
+			status = "disabled";
+
+			usart1: serial@200 {
+				compatible = "atmel,at91sam9260-usart";
+				reg = <0x200 0x200>;
+				interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dma0 AT91_XDMAC_DT_PERID(5)>,
+				       <&dma0 AT91_XDMAC_DT_PERID(4)>;
+				dma-names = "tx", "rx";
+				clocks = <&nic_clk>;
+				clock-names = "usart";
+				atmel,fifo-size = <32>;
+				status = "disabled";
+			};
+
+			spi1: spi@400 {
+				compatible = "atmel,at91rm9200-spi";
+				reg = <0x400 0x200>;
+				interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dma0 AT91_XDMAC_DT_PERID(5)>,
+				       <&dma0 AT91_XDMAC_DT_PERID(4)>;
+				dma-names = "tx", "rx";
+				clocks = <&nic_clk>;
+				clock-names = "spi_clk";
+				atmel,fifo-size = <32>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			i2c1: i2c@600 {
+				compatible = "microchip,sam9x60-i2c";
+				reg = <0x600 0x200>;
+				interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dma0 AT91_XDMAC_DT_PERID(5)>,
+				       <&dma0 AT91_XDMAC_DT_PERID(4)>;
+				dma-names = "tx", "rx";
+				clocks = <&nic_clk>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+		};
+
+		trng: rng@e0048000 {
+			compatible = "atmel,at91sam9g45-trng";
+			reg = <0xe0048000 0x100>;
+			clocks = <&nic_clk>;
+		};
+
+		aes: crypto@e004c000 {
+			compatible = "atmel,at91sam9g46-aes";
+			reg = <0xe004c000 0x100>;
+			interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>;
+			dmas = <&dma0 AT91_XDMAC_DT_PERID(12)>,
+			       <&dma0 AT91_XDMAC_DT_PERID(13)>;
+			dma-names = "tx", "rx";
+			clocks = <&nic_clk>;
+			clock-names = "aes_clk";
+		};
+
+		flx2: flexcom@e0060000 {
+			compatible = "atmel,sama5d2-flexcom";
+			reg = <0xe0060000 0x100>;
+			clocks = <&clks GCK_ID_FLEXCOM2>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0xe0060000 0x800>;
+			status = "disabled";
+
+			usart2: serial@200 {
+				compatible = "atmel,at91sam9260-usart";
+				reg = <0x200 0x200>;
+				interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dma0 AT91_XDMAC_DT_PERID(7)>,
+				       <&dma0 AT91_XDMAC_DT_PERID(6)>;
+				dma-names = "tx", "rx";
+				clocks = <&nic_clk>;
+				clock-names = "usart";
+				atmel,fifo-size = <32>;
+				status = "disabled";
+			};
+
+			spi2: spi@400 {
+				compatible = "atmel,at91rm9200-spi";
+				reg = <0x400 0x200>;
+				interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dma0 AT91_XDMAC_DT_PERID(7)>,
+				       <&dma0 AT91_XDMAC_DT_PERID(6)>;
+				dma-names = "tx", "rx";
+				clocks = <&nic_clk>;
+				clock-names = "spi_clk";
+				atmel,fifo-size = <32>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			i2c2: i2c@600 {
+				compatible = "microchip,sam9x60-i2c";
+				reg = <0x600 0x200>;
+				interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dma0 AT91_XDMAC_DT_PERID(7)>,
+				       <&dma0 AT91_XDMAC_DT_PERID(6)>;
+				dma-names = "tx", "rx";
+				clocks = <&nic_clk>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+		};
+
+		flx3: flexcom@e0064000 {
+			compatible = "atmel,sama5d2-flexcom";
+			reg = <0xe0064000 0x100>;
+			clocks = <&clks GCK_ID_FLEXCOM3>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0xe0064000 0x800>;
+			status = "disabled";
+
+			usart3: serial@200 {
+				compatible = "atmel,at91sam9260-usart";
+				reg = <0x200 0x200>;
+				interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dma0 AT91_XDMAC_DT_PERID(9)>,
+				       <&dma0 AT91_XDMAC_DT_PERID(8)>;
+				dma-names = "tx", "rx";
+				clocks = <&nic_clk>;
+				clock-names = "usart";
+				atmel,fifo-size = <32>;
+				status = "disabled";
+			};
+
+			spi3: spi@400 {
+				compatible = "atmel,at91rm9200-spi";
+				reg = <0x400 0x200>;
+				interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dma0 AT91_XDMAC_DT_PERID(9)>,
+				       <&dma0 AT91_XDMAC_DT_PERID(8)>;
+				dma-names = "tx", "rx";
+				clocks = <&nic_clk>;
+				clock-names = "spi_clk";
+				atmel,fifo-size = <32>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			i2c3: i2c@600 {
+				compatible = "microchip,sam9x60-i2c";
+				reg = <0x600 0x200>;
+				interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dma0 AT91_XDMAC_DT_PERID(9)>,
+				       <&dma0 AT91_XDMAC_DT_PERID(8)>;
+				dma-names = "tx", "rx";
+				clocks = <&nic_clk>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+		};
+
+		dma0: dma-controller@e0068000 {
+			compatible = "microchip,sama7g5-dma";
+			reg = <0xe0068000 0x1000>;
+			interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>;
+			#dma-cells = <1>;
+			clocks = <&nic_clk>;
+			clock-names = "dma_clk";
+		};
+
+		sha: crypto@e006c000 {
+			compatible = "atmel,at91sam9g46-sha";
+			reg = <0xe006c000 0xec>;
+			interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
+			dmas = <&dma0 AT91_XDMAC_DT_PERID(14)>;
+			dma-names = "tx";
+			clocks = <&nic_clk>;
+			clock-names = "sha_clk";
+		};
+
+		flx4: flexcom@e0070000 {
+			compatible = "atmel,sama5d2-flexcom";
+			reg = <0xe0070000 0x100>;
+			clocks = <&clks GCK_ID_FLEXCOM4>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0xe0070000 0x800>;
+			status = "disabled";
+
+			usart4: serial@200 {
+				compatible = "atmel,at91sam9260-usart";
+				reg = <0x200 0x200>;
+				interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dma0 AT91_XDMAC_DT_PERID(11)>,
+				       <&dma0 AT91_XDMAC_DT_PERID(10)>;
+				dma-names = "tx", "rx";
+				clocks = <&nic_clk>;
+				clock-names = "usart";
+				atmel,fifo-size = <32>;
+				status = "disabled";
+			};
+
+			spi4: spi@400 {
+				compatible = "atmel,at91rm9200-spi";
+				reg = <0x400 0x200>;
+				interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dma0 AT91_XDMAC_DT_PERID(11)>,
+				       <&dma0 AT91_XDMAC_DT_PERID(10)>;
+				dma-names = "tx", "rx";
+				clocks = <&nic_clk>;
+				clock-names = "spi_clk";
+				atmel,fifo-size = <32>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			i2c4: i2c@600 {
+				compatible = "microchip,sam9x60-i2c";
+				reg = <0x600 0x200>;
+				interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&dma0 AT91_XDMAC_DT_PERID(11)>,
+				       <&dma0 AT91_XDMAC_DT_PERID(10)>;
+				dma-names = "tx", "rx";
+				clocks = <&nic_clk>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+		};
+
+		timer0: timer@e008c000 {
+			compatible = "snps,dw-apb-timer";
+			reg = <0xe008c000 0x400>;
+			clocks = <&nic_clk>;
+			clock-names = "timer";
+			interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		watchdog: watchdog@e0090000 {
+			compatible = "snps,dw-wdt";
+			reg = <0xe0090000 0x1000>;
+			interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&nic_clk>;
+			status = "disabled";
+		};
+
+		cpu_ctrl: syscon@e00c0000 {
+			compatible = "microchip,lan966x-cpu-syscon", "syscon";
+			reg = <0xe00c0000 0x350>;
+		};
+
+		can0: can@e081c000 {
+			compatible = "bosch,m_can";
+			reg = <0xe081c000 0xfc>, <0x00100000 0x4000>;
+			reg-names = "m_can", "message_ram";
+			interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "int0", "int1";
+			clocks = <&clks GCK_ID_MCAN0>, <&clks GCK_ID_MCAN0>;
+			clock-names = "hclk", "cclk";
+			assigned-clocks = <&clks GCK_ID_MCAN0>;
+			assigned-clock-rates = <40000000>;
+			bosch,mram-cfg = <0x0 0 0 64 0 0 32 32>;
+			status = "disabled";
+		};
+
+		can1: can@e0820000 {
+			compatible = "bosch,m_can";
+			reg = <0xe0820000 0xfc>, <0x00100000 0x8000>;
+			reg-names = "m_can", "message_ram";
+			interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "int0", "int1";
+			clocks = <&clks GCK_ID_MCAN1>, <&clks GCK_ID_MCAN1>;
+			clock-names = "hclk", "cclk";
+			assigned-clocks = <&clks GCK_ID_MCAN1>;
+			assigned-clock-rates = <40000000>;
+			bosch,mram-cfg = <0x4000 0 0 64 0 0 32 32>;
+			status = "disabled";
+		};
+
+		reset: reset-controller@e200400c {
+			compatible = "microchip,lan966x-switch-reset";
+			reg = <0xe200400c 0x4>;
+			reg-names = "gcb";
+			#reset-cells = <1>;
+			cpu-syscon = <&cpu_ctrl>;
+		};
+
+		gpio: pinctrl@e2004064 {
+			compatible = "microchip,lan966x-pinctrl";
+			reg = <0xe2004064 0xb4>,
+			    <0xe2010024 0x138>;
+			resets = <&reset 0>;
+			reset-names = "switch";
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&gpio 0 0 78>;
+			interrupt-controller;
+			interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
+			#interrupt-cells = <2>;
+		};
+
+		mdio0: mdio@e2004118 {
+			compatible = "microchip,lan966x-miim";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0xe2004118 0x24>;
+			clocks = <&sys_clk>;
+			status = "disabled";
+		};
+
+		mdio1: mdio@e200413c {
+			compatible = "microchip,lan966x-miim";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0xe200413c 0x24>,
+			      <0xe2010020 0x4>;
+			clocks = <&sys_clk>;
+			status = "disabled";
+
+			phy0: ethernet-phy@1 {
+				reg = <1>;
+				interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
+				status = "disabled";
+			};
+
+			phy1: ethernet-phy@2 {
+				reg = <2>;
+				interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>;
+				status = "disabled";
+			};
+		};
+
+		sgpio: gpio@e2004190 {
+			compatible = "microchip,sparx5-sgpio";
+			reg = <0xe2004190 0x118>;
+			clocks = <&sys_clk>;
+			resets = <&reset 0>;
+			reset-names = "switch";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			sgpio_in: gpio@0 {
+				compatible = "microchip,sparx5-sgpio-bank";
+				reg = <0>;
+				gpio-controller;
+				#gpio-cells = <3>;
+				interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-controller;
+				#interrupt-cells = <3>;
+			};
+
+			sgpio_out: gpio@1 {
+				compatible = "microchip,sparx5-sgpio-bank";
+				reg = <1>;
+				gpio-controller;
+				#gpio-cells = <3>;
+			};
+		};
+
+		hwmon: hwmon@e2010180 {
+			compatible = "microchip,lan9668-hwmon";
+			reg = <0xe2010180 0xc>,
+			      <0xe20042a8 0xc>;
+			reg-names = "pvt", "fan";
+			clocks = <&sys_clk>;
+		};
+
+		serdes: serdes@e202c000 {
+			compatible = "microchip,lan966x-serdes";
+			reg = <0xe202c000 0x9c>,
+			      <0xe2004010 0x4>;
+			#phy-cells = <2>;
+			status = "disabled";
+		};
+
+		gic: interrupt-controller@e8c11000 {
+			compatible = "arm,gic-400", "arm,cortex-a7-gic";
+			#interrupt-cells = <3>;
+			interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-controller;
+			reg = <0xe8c11000 0x1000>,
+			      <0xe8c12000 0x2000>,
+			      <0xe8c14000 0x2000>,
+			      <0xe8c16000 0x2000>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/logicpd-som-lv-35xx-devkit.dts b/arch/arm/boot/dts/logicpd-som-lv-35xx-devkit.dts
index 2a0a98fe67f0..3240c67e0c39 100644
--- a/arch/arm/boot/dts/logicpd-som-lv-35xx-devkit.dts
+++ b/arch/arm/boot/dts/logicpd-som-lv-35xx-devkit.dts
@@ -11,3 +11,18 @@
 	model = "LogicPD Zoom OMAP35xx SOM-LV Development Kit";
 	compatible = "logicpd,dm3730-som-lv-devkit", "ti,omap3430", "ti,omap3";
 };
+
+&omap3_pmx_core2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&hsusb2_2_pins>;
+	hsusb2_2_pins: pinmux_hsusb2_2_pins {
+		pinctrl-single,pins = <
+			OMAP3430_CORE2_IOPAD(0x25f0, PIN_OUTPUT | MUX_MODE3)            /* etk_d10.hsusb2_clk */
+			OMAP3430_CORE2_IOPAD(0x25f2, PIN_OUTPUT | MUX_MODE3)            /* etk_d11.hsusb2_stp */
+			OMAP3430_CORE2_IOPAD(0x25f4, PIN_INPUT_PULLDOWN | MUX_MODE3)    /* etk_d12.hsusb2_dir */
+			OMAP3430_CORE2_IOPAD(0x25f6, PIN_INPUT_PULLDOWN | MUX_MODE3)    /* etk_d13.hsusb2_nxt */
+			OMAP3430_CORE2_IOPAD(0x25f8, PIN_INPUT_PULLDOWN | MUX_MODE3)    /* etk_d14.hsusb2_data0 */
+			OMAP3430_CORE2_IOPAD(0x25fa, PIN_INPUT_PULLDOWN | MUX_MODE3)    /* etk_d15.hsusb2_data1 */
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/logicpd-som-lv-37xx-devkit.dts b/arch/arm/boot/dts/logicpd-som-lv-37xx-devkit.dts
index a604d92221a4..c757f0d7781c 100644
--- a/arch/arm/boot/dts/logicpd-som-lv-37xx-devkit.dts
+++ b/arch/arm/boot/dts/logicpd-som-lv-37xx-devkit.dts
@@ -11,3 +11,18 @@
 	model = "LogicPD Zoom DM3730 SOM-LV Development Kit";
 	compatible = "logicpd,dm3730-som-lv-devkit", "ti,omap3630", "ti,omap3";
 };
+
+&omap3_pmx_core2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&hsusb2_2_pins>;
+	hsusb2_2_pins: pinmux_hsusb2_2_pins {
+		pinctrl-single,pins = <
+			OMAP3630_CORE2_IOPAD(0x25f0, PIN_OUTPUT | MUX_MODE3)            /* etk_d10.hsusb2_clk */
+			OMAP3630_CORE2_IOPAD(0x25f2, PIN_OUTPUT | MUX_MODE3)            /* etk_d11.hsusb2_stp */
+			OMAP3630_CORE2_IOPAD(0x25f4, PIN_INPUT_PULLDOWN | MUX_MODE3)    /* etk_d12.hsusb2_dir */
+			OMAP3630_CORE2_IOPAD(0x25f6, PIN_INPUT_PULLDOWN | MUX_MODE3)    /* etk_d13.hsusb2_nxt */
+			OMAP3630_CORE2_IOPAD(0x25f8, PIN_INPUT_PULLDOWN | MUX_MODE3)    /* etk_d14.hsusb2_data0 */
+			OMAP3630_CORE2_IOPAD(0x25fa, PIN_INPUT_PULLDOWN | MUX_MODE3)    /* etk_d15.hsusb2_data1 */
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/logicpd-som-lv.dtsi b/arch/arm/boot/dts/logicpd-som-lv.dtsi
index b56524cc7fe2..9ba0ea4eb48a 100644
--- a/arch/arm/boot/dts/logicpd-som-lv.dtsi
+++ b/arch/arm/boot/dts/logicpd-som-lv.dtsi
@@ -27,6 +27,8 @@
 
 	/* HS USB Host PHY on PORT 1 */
 	hsusb2_phy: hsusb2_phy {
+		pinctrl-names = "default";
+		pinctrl-0 = <&hsusb2_reset_pin>;
 		compatible = "usb-nop-xceiv";
 		reset-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>; /* gpio_4 */
 		#phy-cells = <0>;
@@ -144,6 +146,8 @@
 };
 
 &usbhshost {
+	pinctrl-names = "default";
+	pinctrl-0 = <&hsusb2_pins>;
 	port2-mode = "ehci-phy";
 };
 
@@ -151,10 +155,7 @@
 	phys = <0 &hsusb2_phy>;
 };
 
-
 &omap3_pmx_core {
-	pinctrl-names = "default";
-	pinctrl-0 = <&hsusb2_pins>;
 
 	mmc3_pins: pinmux_mm3_pins {
 		pinctrl-single,pins = <
@@ -250,8 +251,7 @@
 };
 
 &omap3_pmx_wkup {
-	pinctrl-names = "default";
-	pinctrl-0 = <&hsusb2_reset_pin>;
+
 	hsusb2_reset_pin: pinmux_hsusb1_reset_pin {
 		pinctrl-single,pins = <
 			OMAP3_WKUP_IOPAD(0x2a0e, PIN_OUTPUT | MUX_MODE4)	/* sys_boot2.gpio_4 */
@@ -265,21 +265,6 @@
 	};
 };
 
-&omap3_pmx_core2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&hsusb2_2_pins>;
-	hsusb2_2_pins: pinmux_hsusb2_2_pins {
-		pinctrl-single,pins = <
-			OMAP3630_CORE2_IOPAD(0x25f0, PIN_OUTPUT | MUX_MODE3)            /* etk_d10.hsusb2_clk */
-			OMAP3630_CORE2_IOPAD(0x25f2, PIN_OUTPUT | MUX_MODE3)            /* etk_d11.hsusb2_stp */
-			OMAP3630_CORE2_IOPAD(0x25f4, PIN_INPUT_PULLDOWN | MUX_MODE3)    /* etk_d12.hsusb2_dir */
-			OMAP3630_CORE2_IOPAD(0x25f6, PIN_INPUT_PULLDOWN | MUX_MODE3)    /* etk_d13.hsusb2_nxt */
-			OMAP3630_CORE2_IOPAD(0x25f8, PIN_INPUT_PULLDOWN | MUX_MODE3)    /* etk_d14.hsusb2_data0 */
-			OMAP3630_CORE2_IOPAD(0x25fa, PIN_INPUT_PULLDOWN | MUX_MODE3)    /* etk_d15.hsusb2_data1 */
-		>;
-	};
-};
-
 &uart2 {
 	interrupts-extended = <&intc 73 &omap3_pmx_core OMAP3_UART2_RX>;
 	pinctrl-names = "default";
diff --git a/arch/arm/boot/dts/logicpd-torpedo-35xx-devkit.dts b/arch/arm/boot/dts/logicpd-torpedo-35xx-devkit.dts
index 57bae2aa910e..cb08aa62d967 100644
--- a/arch/arm/boot/dts/logicpd-torpedo-35xx-devkit.dts
+++ b/arch/arm/boot/dts/logicpd-torpedo-35xx-devkit.dts
@@ -11,3 +11,11 @@
 	model = "LogicPD Zoom OMAP35xx Torpedo Development Kit";
 	compatible = "logicpd,dm3730-torpedo-devkit", "ti,omap3430", "ti,omap3";
 };
+
+&omap3_pmx_core {
+	isp1763_pins: pinmux_isp1763_pins {
+		pinctrl-single,pins = <
+			OMAP3_CORE1_IOPAD(0x2154,  PIN_INPUT_PULLUP | MUX_MODE4)	/* sdmmc1_dat6.gpio_128 */
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/logicpd-torpedo-37xx-devkit.dts b/arch/arm/boot/dts/logicpd-torpedo-37xx-devkit.dts
index 5532db04046c..07ea822fe405 100644
--- a/arch/arm/boot/dts/logicpd-torpedo-37xx-devkit.dts
+++ b/arch/arm/boot/dts/logicpd-torpedo-37xx-devkit.dts
@@ -85,3 +85,12 @@
 		>;
 	};
 };
+
+/* The gpio muxing between omap3530 and dm3730 is different for GPIO_128 */
+&omap3_pmx_wkup {
+	isp1763_pins: pinmux_isp1763_pins {
+		pinctrl-single,pins = <
+			OMAP3_WKUP_IOPAD(0x2a58, PIN_INPUT_PULLUP | MUX_MODE4)	/* reserved.gpio_128 */
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/logicpd-torpedo-baseboard.dtsi b/arch/arm/boot/dts/logicpd-torpedo-baseboard.dtsi
index 533a47bc4a53..d3da8b1b473b 100644
--- a/arch/arm/boot/dts/logicpd-torpedo-baseboard.dtsi
+++ b/arch/arm/boot/dts/logicpd-torpedo-baseboard.dtsi
@@ -93,7 +93,8 @@
 
 &gpmc {
 	ranges = <0 0 0x30000000 0x1000000	/* CS0: 16MB for NAND */
-		  1 0 0x2c000000 0x1000000>;	/* CS1: 16MB for LAN9221 */
+		  1 0 0x2c000000 0x1000000	/* CS1: 16MB for LAN9221 */
+		  6 0 0x28000000 0x1000000>;	/* CS6: 16MB for ISP1763 */
 
 	ethernet@gpmc {
 		pinctrl-names = "default";
@@ -102,6 +103,44 @@
 		interrupts = <1 IRQ_TYPE_LEVEL_LOW>;		/* gpio129 */
 		reg = <1 0 0xff>;
 	};
+
+	usb@6,0 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&isp1763_pins>;
+		compatible = "nxp,usb-isp1763";
+		reg = <0x6 0x0 0xff>;
+		interrupt-parent = <&gpio5>;
+		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-names = "host";
+		bus-width = <16>;
+		dr_mode = "host";
+		gpmc,mux-add-data = <0>;
+		gpmc,device-width = <2>;
+		gpmc,wait-pin = <0>;
+		gpmc,burst-length = <4>;
+		gpmc,cycle2cycle-samecsen;
+		gpmc,cycle2cycle-diffcsen;
+		gpmc,cs-on-ns = <0>;
+		gpmc,cs-rd-off-ns = <45>;
+		gpmc,cs-wr-off-ns = <45>;
+		gpmc,adv-on-ns = <0>;
+		gpmc,adv-rd-off-ns = <0>;
+		gpmc,adv-wr-off-ns = <0>;
+		gpmc,oe-on-ns = <0>;
+		gpmc,oe-off-ns = <45>;
+		gpmc,we-on-ns = <0>;
+		gpmc,we-off-ns = <25>;
+		gpmc,rd-cycle-ns = <60>;
+		gpmc,wr-cycle-ns = <45>;
+		gpmc,access-ns = <35>;
+		gpmc,page-burst-access-ns = <0>;
+		gpmc,bus-turnaround-ns = <0>;
+		gpmc,cycle2cycle-delay-ns = <60>;
+		gpmc,wait-monitoring-ns = <0>;
+		gpmc,clk-activation-ns = <0>;
+		gpmc,wr-data-mux-bus-ns = <5>;
+		gpmc,wr-access-ns = <20>;
+	};
 };
 
 &hdqw1w {
diff --git a/arch/arm/boot/dts/lpc18xx.dtsi b/arch/arm/boot/dts/lpc18xx.dtsi
index 10b8249b8ab6..1bb686a7b3ec 100644
--- a/arch/arm/boot/dts/lpc18xx.dtsi
+++ b/arch/arm/boot/dts/lpc18xx.dtsi
@@ -121,7 +121,7 @@
 			status = "disabled";
 		};
 
-		usb0: ehci@40006100 {
+		usb0: usb@40006100 {
 			compatible = "nxp,lpc1850-ehci", "generic-ehci";
 			reg = <0x40006100 0x100>;
 			interrupts = <8>;
@@ -133,7 +133,7 @@
 			status = "disabled";
 		};
 
-		usb1: ehci@40007100 {
+		usb1: usb@40007100 {
 			compatible = "nxp,lpc1850-ehci", "generic-ehci";
 			reg = <0x40007100 0x100>;
 			interrupts = <9>;
@@ -183,7 +183,7 @@
 			compatible = "nxp,lpc1850-dwmac", "snps,dwmac-3.611", "snps,dwmac";
 			reg = <0x40010000 0x2000>;
 			interrupts = <5>;
-			interrupt-names	= "macirq";
+			interrupt-names = "macirq";
 			clocks = <&ccu1 CLK_CPU_ETHERNET>;
 			clock-names = "stmmaceth";
 			resets = <&rgu 22>;
diff --git a/arch/arm/boot/dts/ls1021a-iot.dts b/arch/arm/boot/dts/ls1021a-iot.dts
new file mode 100644
index 000000000000..ce8e26d7791f
--- /dev/null
+++ b/arch/arm/boot/dts/ls1021a-iot.dts
@@ -0,0 +1,227 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright 2021-2022 NXP
+ *
+ */
+
+/dts-v1/;
+#include "ls1021a.dtsi"
+
+/ {
+	model = "LS1021A-IOT Board";
+	compatible = "fsl,ls1021a-iot", "fsl,ls1021a";
+
+	sys_mclk: clock-mclk {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <24576000>;
+	};
+
+	reg_3p3v: regulator-3V3 {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	reg_2p5v: regulator-2V5 {
+		compatible = "regulator-fixed";
+		regulator-name = "2P5V";
+		regulator-min-microvolt = <2500000>;
+		regulator-max-microvolt = <2500000>;
+		regulator-always-on;
+	};
+
+	sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,format = "i2s";
+		simple-audio-card,widgets =
+			"Microphone", "Microphone Jack",
+			"Headphone", "Headphone Jack",
+			"Speaker", "Speaker Ext",
+			"Line", "Line In Jack";
+		simple-audio-card,routing =
+			"MIC_IN", "Microphone Jack",
+			"Microphone Jack", "Mic Bias",
+			"LINE_IN", "Line In Jack",
+			"Headphone Jack", "HP_OUT",
+			"Speaker Ext", "LINE_OUT";
+
+		simple-audio-card,cpu {
+			sound-dai = <&sai2>;
+			frame-master;
+			bitclock-master;
+		};
+
+		simple-audio-card,codec {
+			sound-dai = <&sgtl5000>;
+			frame-master;
+			bitclock-master;
+		};
+	};
+};
+
+&can0{
+	status = "disabled";
+};
+
+&can1{
+	status = "disabled";
+};
+
+&can2{
+	status = "disabled";
+};
+
+&can3{
+	status = "okay";
+};
+
+&dcu {
+	display = <&display>;
+	status = "okay";
+
+	display: display@0 {
+		bits-per-pixel = <24>;
+
+		display-timings {
+			native-mode = <&timing0>;
+
+			timing0: mode0 {
+				clock-frequency = <25000000>;
+				hactive = <640>;
+				vactive = <480>;
+				hback-porch = <80>;
+				hfront-porch = <80>;
+				vback-porch = <16>;
+				vfront-porch = <16>;
+				hsync-len = <12>;
+				vsync-len = <2>;
+				hsync-active = <1>;
+				vsync-active = <1>;
+			};
+		};
+	};
+};
+
+&enet0 {
+	tbi-handle = <&tbi1>;
+	phy-handle = <&phy1>;
+	phy-connection-type = "sgmii";
+	status = "okay";
+};
+
+&enet1 {
+	tbi-handle = <&tbi1>;
+	phy-handle = <&phy3>;
+	phy-connection-type = "sgmii";
+	status = "okay";
+};
+
+&enet2 {
+	fixed-link = <0 1 1000 0 0>;
+	phy-connection-type = "rgmii-id";
+	status = "okay";
+};
+
+&esdhc{
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	pca9555: gpio@23 {
+		compatible = "nxp,pca9555";
+		reg = <0x23>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	sgtl5000: audio-codec@2a {
+		#sound-dai-cells = <0x0>;
+		compatible = "fsl,sgtl5000";
+		reg = <0x2a>;
+		VDDA-supply = <&reg_3p3v>;
+		VDDIO-supply = <&reg_2p5v>;
+		clocks = <&sys_mclk>;
+	};
+
+	max1239: adc@35 {
+		compatible = "maxim,max1239";
+		reg = <0x35>;
+		#io-channel-cells = <1>;
+	};
+
+	ina2201: core-monitor@44 {
+		compatible = "ti,ina220";
+		reg = <0x44>;
+		shunt-resistor = <1000>;
+	};
+
+	ina2202: current-monitor@45 {
+		compatible = "ti,ina220";
+		reg = <0x45>;
+		shunt-resistor = <1000>;
+	};
+
+	lm75b: thermal-monitor@48 {
+		compatible = "national,lm75b";
+		reg = <0x48>;
+	};
+};
+
+&lpuart0 {
+	status = "okay";
+};
+
+&mdio0 {
+	phy0: ethernet-phy@0 {
+		reg = <0x0>;
+	};
+
+	phy1: ethernet-phy@1 {
+		reg = <0x1>;
+	};
+
+	phy2: ethernet-phy@2 {
+		reg = <0x2>;
+	};
+
+	phy3: ethernet-phy@3 {
+		reg = <0x3>;
+	};
+
+	tbi1: tbi-phy@1f {
+		reg = <0x1f>;
+		device_type = "tbi-phy";
+	};
+};
+
+&qspi {
+	num-cs = <2>;
+	status = "okay";
+
+	s25fl128s: flash@0 {
+		compatible = "jedec,spi-nor";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		spi-max-frequency = <20000000>;
+		reg = <0>;
+	};
+};
+
+&sai2 {
+	status = "okay";
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/ls1021a-tsn.dts b/arch/arm/boot/dts/ls1021a-tsn.dts
index ff0ffb22768b..1ea32fff4120 100644
--- a/arch/arm/boot/dts/ls1021a-tsn.dts
+++ b/arch/arm/boot/dts/ls1021a-tsn.dts
@@ -91,6 +91,8 @@
 				/* Internal port connected to eth2 */
 				ethernet = <&enet2>;
 				phy-mode = "rgmii";
+				rx-internal-delay-ps = <0>;
+				tx-internal-delay-ps = <0>;
 				reg = <4>;
 
 				fixed-link {
diff --git a/arch/arm/boot/dts/ls1021a.dtsi b/arch/arm/boot/dts/ls1021a.dtsi
index 2e69d6eab4d1..7c5510e34494 100644
--- a/arch/arm/boot/dts/ls1021a.dtsi
+++ b/arch/arm/boot/dts/ls1021a.dtsi
@@ -122,13 +122,20 @@
 			interrupts = <GIC_SPI 180 IRQ_TYPE_LEVEL_HIGH>;
 		};
 
-		ifc: ifc@1530000 {
-			compatible = "fsl,ifc", "simple-bus";
+		ifc: memory-controller@1530000 {
+			compatible = "fsl,ifc";
 			reg = <0x0 0x1530000 0x0 0x10000>;
 			interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
 			status = "disabled";
 		};
 
+		sfp: efuse@1e80000 {
+			compatible = "fsl,ls1021a-sfp";
+			reg = <0x0 0x1e80000 0x0 0x10000>;
+			clocks = <&clockgen 4 3>;
+			clock-names = "sfp";
+		};
+
 		dcfg: dcfg@1ee0000 {
 			compatible = "fsl,ls1021a-dcfg", "syscon";
 			reg = <0x0 0x1ee0000 0x0 0x1000>;
@@ -192,7 +199,7 @@
 					<3 0 &gic GIC_SPI 167 IRQ_TYPE_LEVEL_HIGH>,
 					<4 0 &gic GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>,
 					<5 0 &gic GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>;
-				interrupt-map-mask = <0xffffffff 0x0>;
+				interrupt-map-mask = <0x7 0x0>;
 			};
 		};
 
@@ -640,7 +647,7 @@
 			status = "disabled";
 		};
 
-		edma0: edma@2c00000 {
+		edma0: dma-controller@2c00000 {
 			#dma-cells = <2>;
 			compatible = "fsl,vf610-edma";
 			reg = <0x0 0x2c00000 0x0 0x10000>,
diff --git a/arch/arm/boot/dts/mba6ulx.dtsi b/arch/arm/boot/dts/mba6ulx.dtsi
new file mode 100644
index 000000000000..aac42df9ecf6
--- /dev/null
+++ b/arch/arm/boot/dts/mba6ulx.dtsi
@@ -0,0 +1,569 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2018-2022 TQ-Systems GmbH
+ * Author: Markus Niebel <Markus.Niebel@tq-group.com>
+ */
+
+/ {
+	model = "TQ-Systems MBA6ULx Baseboard";
+
+	aliases {
+		mmc0 = &usdhc2;
+		mmc1 = &usdhc1;
+		rtc0 = &rtc0;
+		rtc1 = &snvs_rtc;
+	};
+
+	chosen {
+		stdout-path = &uart1;
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		power-supply = <&reg_mba6ul_3v3>;
+		enable-gpios = <&expander_out0 4 GPIO_ACTIVE_HIGH>;
+		status = "disabled";
+	};
+
+	beeper: beeper {
+		compatible = "gpio-beeper";
+		gpios = <&expander_out1 6 GPIO_ACTIVE_HIGH>;
+	};
+
+	gpio_buttons: gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_buttons>;
+
+		button1 {
+			label = "s14";
+			linux,code = <KEY_1>;
+			gpios = <&expander_in0 0 GPIO_ACTIVE_LOW>;
+		};
+
+		button2 {
+			label = "s6";
+			linux,code = <KEY_2>;
+			gpios = <&expander_in0 1 GPIO_ACTIVE_LOW>;
+		};
+
+		button3 {
+			label = "s7";
+			linux,code = <KEY_3>;
+			gpios = <&expander_in0 2 GPIO_ACTIVE_LOW>;
+		};
+
+		power-button {
+			label = "POWER";
+			linux,code = <KEY_POWER>;
+			gpios = <&gpio1 3 GPIO_ACTIVE_LOW>;
+			gpio-key,wakeup;
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+		status = "okay";
+
+		led1 {
+			label = "led1";
+			gpios = <&expander_out1 4 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-on";
+		};
+
+		led2 {
+			label = "led2";
+			gpios = <&expander_out1 5 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	reg_lcd_pwr: regulator-lcd-pwr {
+		compatible = "regulator-fixed";
+		regulator-name = "lcd-pwr";
+		gpio = <&expander_out0 1 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		status = "disabled";
+	};
+
+	reg_mba6ul_3v3: regulator-mba6ul-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "supply-mba6ul-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	reg_mba6ul_5v0: regulator-mba6ul-5v0 {
+		compatible = "regulator-fixed";
+		regulator-name = "supply-mba6ul-5v0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+
+	reg_mpcie: regulator-mpcie-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "mpcie-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&expander_out0 2 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-always-on;
+		startup-delay-us = <500000>;
+		vin-supply = <&reg_mba6ul_3v3>;
+	};
+
+	reg_otg2vbus_5v0: regulator-otg2-vbus-5v0 {
+		compatible = "regulator-fixed";
+		gpio = <&expander_out1 0 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-name = "otg2-vbus-supply-5v0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&reg_mpcie>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		linux,cma {
+			compatible = "shared-dma-pool";
+			reusable;
+			size = <0x6000000>;
+			linux,cma-default;
+		};
+	};
+
+	sound {
+		compatible = "fsl,imx-audio-tlv320aic32x4";
+		model = "imx-audio-tlv320aic32x4";
+		ssi-controller = <&sai1>;
+		audio-codec = <&tlv320aic32x4>;
+		audio-asrc = <&asrc>;
+	};
+};
+
+&can1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan1>;
+	xceiver-supply = <&reg_mba6ul_3v3>;
+	status = "okay";
+};
+
+&can2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan2>;
+	xceiver-supply = <&reg_mba6ul_3v3>;
+	status = "okay";
+};
+
+&clks {
+	assigned-clocks = <&clks IMX6UL_CLK_PLL4_AUDIO_DIV>;
+	assigned-clock-rates = <768000000>;
+};
+
+&ecspi2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi2>;
+	num-cs = <1>;
+	status = "okay";
+};
+
+&fec1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet1>;
+	phy-mode = "rmii";
+	phy-handle = <&ethphy0>;
+	phy-supply = <&reg_mba6ul_3v3>;
+	phy-reset-gpios = <&expander_out1 1 GPIO_ACTIVE_LOW>;
+	phy-reset-duration = <25>;
+	phy-reset-post-delay = <1>;
+	status = "okay";
+};
+
+&fec2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet2>, <&pinctrl_enet2_mdc>;
+	phy-mode = "rmii";
+	phy-handle = <&ethphy1>;
+	phy-supply = <&reg_mba6ul_3v3>;
+	phy-reset-gpios = <&expander_out1 2 GPIO_ACTIVE_LOW>;
+	phy-reset-duration = <25>;
+	phy-reset-post-delay = <1>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy0: ethernet-phy@0 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			clocks = <&clks IMX6UL_CLK_ENET_REF>;
+			reg = <0>;
+			max-speed = <100>;
+		};
+
+		ethphy1: ethernet-phy@1 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			clocks = <&clks IMX6UL_CLK_ENET2_REF_125M>;
+			reg = <1>;
+			max-speed = <100>;
+		};
+	};
+};
+
+&i2c4 {
+	tlv320aic32x4: audio-codec@18 {
+		compatible = "ti,tlv320aic32x4";
+		reg = <0x18>;
+		clocks = <&clks IMX6UL_CLK_SAI1>;
+		clock-names = "mclk";
+		ldoin-supply = <&reg_mba6ul_3v3>;
+		iov-supply = <&reg_mba6ul_3v3>;
+	};
+
+	jc42: temperature-sensor@19 {
+		compatible = "nxp,se97", "jedec,jc-42.4-temp";
+		reg = <0x19>;
+	};
+
+	expander_out0: gpio-expander@20 {
+		compatible = "nxp,pca9554";
+		reg = <0x20>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	expander_in0: gpio-expander@21 {
+		compatible = "nxp,pca9554";
+		reg = <0x21>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_expander_in0>;
+		interrupt-parent = <&gpio4>;
+		interrupts = <23 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		enet1_int-hog {
+			gpio-hog;
+			gpios = <6 0>;
+			input;
+		};
+
+		enet2_int-hog {
+			gpio-hog;
+			gpios = <7 0>;
+			input;
+		};
+	};
+
+	expander_out1: gpio-expander@22 {
+		compatible = "nxp,pca9554";
+		reg = <0x22>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	analog_touch: touchscreen@41 {
+		compatible = "st,stmpe811";
+		reg = <0x41>;
+		interrupts = <21 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-parent = <&gpio4>;
+		interrupt-controller;
+		status = "disabled";
+
+		stmpe_touchscreen {
+			compatible = "st,stmpe-ts";
+			st,adc-freq = <1>;      /* 3.25 MHz ADC clock speed */
+			st,ave-ctrl = <3>;      /* 8 sample average control */
+			st,fraction-z = <7>;    /* 7 length fractional part in z */
+			/*
+			 * 50 mA typical 80 mA max touchscreen drivers
+			 * current limit value
+			 */
+			st,i-drive = <1>;
+			st,mod-12b = <1>;       /* 12-bit ADC */
+			st,ref-sel = <0>;       /* internal ADC reference */
+			st,sample-time = <4>;   /* ADC converstion time: 80 clocks */
+			st,settling = <3>;      /* 1 ms panel driver settling time */
+			st,touch-det-delay = <5>; /* 5 ms touch detect interrupt delay */
+		};
+	};
+
+	/* NXP SE97BTP with temperature sensor + eeprom */
+	se97b: eeprom@51 {
+		compatible = "nxp,se97b", "atmel,24c02";
+		reg = <0x51>;
+		pagesize = <16>;
+	};
+};
+
+&pwm2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm2>;
+	status = "okay";
+};
+
+&sai1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sai1>;
+	assigned-clocks = <&clks IMX6UL_CLK_SAI1_SEL>,
+			  <&clks IMX6UL_CLK_SAI1>;
+	assigned-clock-parents = <&clks IMX6UL_CLK_PLL4_AUDIO_DIV>;
+	assigned-clock-rates = <0>, <24000000>;
+	fsl,sai-mclk-direction-output;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	status = "okay";
+};
+
+&uart6 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart6>;
+	/* for DTE mode, add below change */
+	/* fsl,dte-mode; */
+	/* pinctrl-0 = <&pinctrl_uart6dte>; */
+	uart-has-rtscts;
+	linux,rs485-enabled-at-boot-time;
+	rs485-rts-active-low;
+	rs485-rx-during-tx;
+	status = "okay";
+};
+
+/* otg-port */
+&usbotg1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb_otg1>;
+	power-active-high;
+	over-current-active-low;
+	/* we implement only dual role but not a fully featured OTG */
+	hnp-disable;
+	srp-disable;
+	adp-disable;
+	dr_mode = "otg";
+	status = "okay";
+};
+
+/* 7-port usb hub */
+/* id, pwr, oc pins not connected */
+&usbotg2 {
+	disable-over-current;
+	vbus-supply = <&reg_otg2vbus_5v0>;
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usdhc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	cd-gpios = <&gpio1 19 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio1 18 GPIO_ACTIVE_HIGH>;
+	bus-width = <4>;
+	vmmc-supply = <&reg_mba6ul_3v3>;
+	vqmmc-supply = <&reg_vccsd>;
+	no-1-8-v;
+	no-mmc;
+	no-sdio;
+	status = "okay";
+};
+
+&wdog1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog1>;
+	fsl,ext-reset-output;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_buttons: buttonsgrp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO03__GPIO1_IO03	0x100b0
+		>;
+	};
+
+	pinctrl_ecspi2: ecspi2grp {
+		fsl,pins = <
+			MX6UL_PAD_UART4_TX_DATA__ECSPI2_SCLK	0x1b020
+			MX6UL_PAD_UART5_RX_DATA__ECSPI2_MISO	0x1b020
+			MX6UL_PAD_UART5_TX_DATA__ECSPI2_MOSI	0x1b020
+			MX6UL_PAD_UART4_RX_DATA__ECSPI2_SS0	0x1b020
+		>;
+	};
+
+	pinctrl_enet1: enet1grp {
+		fsl,pins = <
+			MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN	0x1b0b0
+			MX6UL_PAD_ENET1_RX_ER__ENET1_RX_ER	0x1b0b0
+			MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00	0x1b0b0
+			MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01	0x1b0b0
+			MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00	0x1b0b0
+			MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01	0x1b0b0
+			MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN	0x1b0b0
+			MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1	0x4001b0a8
+		>;
+	};
+
+	pinctrl_enet2: enet2grp {
+		fsl,pins = <
+			MX6UL_PAD_ENET2_RX_EN__ENET2_RX_EN	0x1b0b0
+			MX6UL_PAD_ENET2_RX_ER__ENET2_RX_ER	0x1b0b0
+			MX6UL_PAD_ENET2_RX_DATA0__ENET2_RDATA00	0x1b0b0
+			MX6UL_PAD_ENET2_RX_DATA1__ENET2_RDATA01	0x1b0b0
+			MX6UL_PAD_ENET2_TX_DATA0__ENET2_TDATA00	0x1b0a0
+			MX6UL_PAD_ENET2_TX_DATA1__ENET2_TDATA01	0x1b0a0
+			MX6UL_PAD_ENET2_TX_EN__ENET2_TX_EN	0x1b0b0
+			MX6UL_PAD_ENET2_TX_CLK__ENET2_REF_CLK2	0x4001b0a8
+		>;
+	};
+
+	pinctrl_enet2_mdc: enet2mdcgrp {
+		fsl,pins = <
+			/* mdio */
+			MX6UL_PAD_GPIO1_IO07__ENET2_MDC		0x1b0b0
+			MX6UL_PAD_GPIO1_IO06__ENET2_MDIO	0x1b0b0
+		>;
+	};
+
+	pinctrl_expander_in0: expanderin0grp {
+		fsl,pins = <
+			MX6UL_PAD_CSI_DATA02__GPIO4_IO23	0x1b0b1
+		>;
+	};
+
+	pinctrl_flexcan1: flexcan1grp {
+		fsl,pins = <
+			MX6UL_PAD_UART3_RTS_B__FLEXCAN1_RX	0x1b020
+			MX6UL_PAD_UART3_CTS_B__FLEXCAN1_TX	0x1b020
+		>;
+	};
+
+	pinctrl_flexcan2: flexcan2grp {
+		fsl,pins = <
+			MX6UL_PAD_UART2_RTS_B__FLEXCAN2_RX	0x1b020
+			MX6UL_PAD_UART2_CTS_B__FLEXCAN2_TX	0x1b020
+		>;
+	};
+
+	pinctrl_pwm2: pwm2grp {
+		fsl,pins = <
+			/* 100 k PD, DSE 120 OHM, SPPEED LO */
+			MX6UL_PAD_GPIO1_IO09__PWM2_OUT		0x00003050
+		>;
+	};
+
+	pinctrl_sai1: sai1grp {
+		fsl,pins = <
+			MX6UL_PAD_CSI_DATA05__SAI1_TX_BCLK	0x1b0b1
+			MX6UL_PAD_CSI_DATA04__SAI1_TX_SYNC	0x1b0b1
+			MX6UL_PAD_CSI_DATA07__SAI1_TX_DATA	0x1f0b8
+			MX6UL_PAD_CSI_DATA06__SAI1_RX_DATA	0x110b0
+			MX6UL_PAD_CSI_DATA01__SAI1_MCLK		0x1b0b1
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX	0x1b0b1
+			MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <
+			MX6UL_PAD_UART3_TX_DATA__UART3_DCE_TX	0x1b0b1
+			MX6UL_PAD_UART3_RX_DATA__UART3_DCE_RX	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart6: uart6grp {
+		fsl,pins = <
+			MX6UL_PAD_CSI_MCLK__UART6_DCE_TX	0x1b0b1
+			MX6UL_PAD_CSI_PIXCLK__UART6_DCE_RX	0x1b0b1
+			MX6UL_PAD_CSI_VSYNC__UART6_DCE_RTS	0x1b0b1
+			MX6UL_PAD_CSI_HSYNC__UART6_DCE_CTS	0x1b0b1
+		>;
+	};
+
+	pinctrl_uart6dte: uart6dte {
+		fsl,pins = <
+			MX6UL_PAD_CSI_PIXCLK__UART6_DTE_TX	0x1b0b1
+			MX6UL_PAD_CSI_MCLK__UART6_DTE_RX	0x1b0b1
+			MX6UL_PAD_CSI_HSYNC__UART6_DTE_RTS	0x1b0b1
+			MX6UL_PAD_CSI_VSYNC__UART6_DTE_CTS	0x1b0b1
+		>;
+	};
+
+	pinctrl_usb_otg1: usbotg1grp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO00__ANATOP_OTG1_ID	0x00017059
+			MX6UL_PAD_GPIO1_IO01__USB_OTG1_OC	0x0001b0b0
+			MX6UL_PAD_GPIO1_IO04__USB_OTG1_PWR	0x0001b099
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x00017069
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x00017059
+			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x00017059
+			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x00017059
+			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x00017059
+			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x00017059
+			/* WP */
+			MX6UL_PAD_UART1_CTS_B__GPIO1_IO18	0x0001b099
+			/* CD */
+			MX6UL_PAD_UART1_RTS_B__GPIO1_IO19	0x0001b099
+		>;
+	};
+
+	pinctrl_usdhc1_100mhz: usdhc1grp100mhz {
+		fsl,pins = <
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x00017069
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x000170b9
+			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x000170b9
+			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x000170b9
+			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x000170b9
+			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x000170b9
+			/* WP */
+			MX6UL_PAD_UART1_CTS_B__GPIO1_IO18	0x0001b099
+			/* CD */
+			MX6UL_PAD_UART1_RTS_B__GPIO1_IO19	0x0001b099
+		>;
+	};
+
+	pinctrl_usdhc1_200mhz: usdhc1grp200mhz {
+		fsl,pins = <
+			MX6UL_PAD_SD1_CLK__USDHC1_CLK		0x00017069
+			MX6UL_PAD_SD1_CMD__USDHC1_CMD		0x000170f9
+			MX6UL_PAD_SD1_DATA0__USDHC1_DATA0	0x000170f9
+			MX6UL_PAD_SD1_DATA1__USDHC1_DATA1	0x000170f9
+			MX6UL_PAD_SD1_DATA2__USDHC1_DATA2	0x000170f9
+			MX6UL_PAD_SD1_DATA3__USDHC1_DATA3	0x000170f9
+			/* WP */
+			MX6UL_PAD_UART1_CTS_B__GPIO1_IO18	0x0001b099
+			/* CD */
+			MX6UL_PAD_UART1_RTS_B__GPIO1_IO19	0x0001b099
+		>;
+	};
+
+	pinctrl_wdog1: wdog1grp {
+		fsl,pins = <
+			MX6UL_PAD_GPIO1_IO08__WDOG1_WDOG_B	0x0001b099
+		>;
+	};
+};
diff --git a/arch/arm/boot/dts/meson.dtsi b/arch/arm/boot/dts/meson.dtsi
index 3be7cba603d5..8e3860d5d916 100644
--- a/arch/arm/boot/dts/meson.dtsi
+++ b/arch/arm/boot/dts/meson.dtsi
@@ -59,7 +59,7 @@
 			};
 
 			uart_A: serial@84c0 {
-				compatible = "amlogic,meson6-uart", "amlogic,meson-uart";
+				compatible = "amlogic,meson6-uart";
 				reg = <0x84c0 0x18>;
 				interrupts = <GIC_SPI 26 IRQ_TYPE_EDGE_RISING>;
 				fifo-size = <128>;
@@ -67,7 +67,7 @@
 			};
 
 			uart_B: serial@84dc {
-				compatible = "amlogic,meson6-uart", "amlogic,meson-uart";
+				compatible = "amlogic,meson6-uart";
 				reg = <0x84dc 0x18>;
 				interrupts = <GIC_SPI 75 IRQ_TYPE_EDGE_RISING>;
 				status = "disabled";
@@ -105,7 +105,7 @@
 			};
 
 			uart_C: serial@8700 {
-				compatible = "amlogic,meson6-uart", "amlogic,meson-uart";
+				compatible = "amlogic,meson6-uart";
 				reg = <0x8700 0x18>;
 				interrupts = <GIC_SPI 93 IRQ_TYPE_EDGE_RISING>;
 				status = "disabled";
@@ -214,21 +214,21 @@
 			ranges = <0x0 0xc8100000 0x100000>;
 
 			ao_arc_rproc: remoteproc@1c {
-				compatible= "amlogic,meson-mx-ao-arc";
+				compatible = "amlogic,meson-mx-ao-arc";
 				reg = <0x1c 0x8>, <0x38 0x8>;
 				reg-names = "remap", "cpu";
 				status = "disabled";
 			};
 
 			ir_receiver: ir-receiver@480 {
-				compatible= "amlogic,meson6-ir";
+				compatible = "amlogic,meson6-ir";
 				reg = <0x480 0x20>;
 				interrupts = <GIC_SPI 15 IRQ_TYPE_EDGE_RISING>;
 				status = "disabled";
 			};
 
 			uart_AO: serial@4c0 {
-				compatible = "amlogic,meson6-uart", "amlogic,meson-ao-uart", "amlogic,meson-uart";
+				compatible = "amlogic,meson6-uart", "amlogic,meson-ao-uart";
 				reg = <0x4c0 0x18>;
 				interrupts = <GIC_SPI 90 IRQ_TYPE_EDGE_RISING>;
 				status = "disabled";
diff --git a/arch/arm/boot/dts/meson8-minix-neo-x8.dts b/arch/arm/boot/dts/meson8-minix-neo-x8.dts
index 61ec929ab86e..56ea875c418c 100644
--- a/arch/arm/boot/dts/meson8-minix-neo-x8.dts
+++ b/arch/arm/boot/dts/meson8-minix-neo-x8.dts
@@ -65,7 +65,7 @@
 	pinctrl-0 = <&spi_nor_pins>;
 	pinctrl-names = "default";
 
-	spi-flash@0 {
+	flash@0 {
 		compatible = "mxicy,mx25l1606e";
 		#address-cells = <1>;
 		#size-cells = <1>;
diff --git a/arch/arm/boot/dts/meson8.dtsi b/arch/arm/boot/dts/meson8.dtsi
index f80ddc98d3a2..0f8bac8bac8b 100644
--- a/arch/arm/boot/dts/meson8.dtsi
+++ b/arch/arm/boot/dts/meson8.dtsi
@@ -430,7 +430,7 @@
 };
 
 &ao_arc_rproc {
-	compatible= "amlogic,meson8-ao-arc", "amlogic,meson-mx-ao-arc";
+	compatible = "amlogic,meson8-ao-arc", "amlogic,meson-mx-ao-arc";
 	amlogic,secbus2 = <&secbus2>;
 	sram = <&ao_arc_sram>;
 	resets = <&reset RESET_MEDIA_CPU>;
@@ -736,27 +736,27 @@
 };
 
 &uart_AO {
-	compatible = "amlogic,meson8-uart", "amlogic,meson-uart";
-	clocks = <&clkc CLKID_CLK81>, <&xtal>, <&clkc CLKID_CLK81>;
-	clock-names = "baud", "xtal", "pclk";
+	compatible = "amlogic,meson8-uart", "amlogic,meson-ao-uart";
+	clocks = <&xtal>, <&clkc CLKID_CLK81>, <&clkc CLKID_CLK81>;
+	clock-names = "xtal", "pclk", "baud";
 };
 
 &uart_A {
-	compatible = "amlogic,meson8-uart", "amlogic,meson-uart";
-	clocks = <&clkc CLKID_CLK81>, <&xtal>, <&clkc CLKID_UART0>;
-	clock-names = "baud", "xtal", "pclk";
+	compatible = "amlogic,meson8-uart";
+	clocks = <&xtal>, <&clkc CLKID_UART0>, <&clkc CLKID_CLK81>;
+	clock-names = "xtal", "pclk", "baud";
 };
 
 &uart_B {
-	compatible = "amlogic,meson8-uart", "amlogic,meson-uart";
-	clocks = <&clkc CLKID_CLK81>, <&xtal>, <&clkc CLKID_UART1>;
-	clock-names = "baud", "xtal", "pclk";
+	compatible = "amlogic,meson8-uart";
+	clocks = <&xtal>, <&clkc CLKID_UART0>, <&clkc CLKID_CLK81>;
+	clock-names = "xtal", "pclk", "baud";
 };
 
 &uart_C {
-	compatible = "amlogic,meson8-uart", "amlogic,meson-uart";
-	clocks = <&clkc CLKID_CLK81>, <&xtal>, <&clkc CLKID_UART2>;
-	clock-names = "baud", "xtal", "pclk";
+	compatible = "amlogic,meson8-uart";
+	clocks = <&xtal>, <&clkc CLKID_UART0>, <&clkc CLKID_CLK81>;
+	clock-names = "xtal", "pclk", "baud";
 };
 
 &usb0 {
diff --git a/arch/arm/boot/dts/meson8b.dtsi b/arch/arm/boot/dts/meson8b.dtsi
index b49b7cbaed4e..cf9c04a61ba3 100644
--- a/arch/arm/boot/dts/meson8b.dtsi
+++ b/arch/arm/boot/dts/meson8b.dtsi
@@ -384,7 +384,7 @@
 };
 
 &ao_arc_rproc {
-	compatible= "amlogic,meson8b-ao-arc", "amlogic,meson-mx-ao-arc";
+	compatible = "amlogic,meson8b-ao-arc", "amlogic,meson-mx-ao-arc";
 	amlogic,secbus2 = <&secbus2>;
 	sram = <&ao_arc_sram>;
 	resets = <&reset RESET_MEDIA_CPU>;
@@ -724,27 +724,27 @@
 };
 
 &uart_AO {
-	compatible = "amlogic,meson8b-uart", "amlogic,meson-uart";
-	clocks = <&clkc CLKID_CLK81>, <&xtal>, <&clkc CLKID_CLK81>;
-	clock-names = "baud", "xtal", "pclk";
+	compatible = "amlogic,meson8b-uart", "amlogic,meson-ao-uart";
+	clocks = <&xtal>, <&clkc CLKID_CLK81>, <&clkc CLKID_CLK81>;
+	clock-names = "xtal", "pclk", "baud";
 };
 
 &uart_A {
-	compatible = "amlogic,meson8b-uart", "amlogic,meson-uart";
-	clocks = <&clkc CLKID_CLK81>, <&xtal>, <&clkc CLKID_UART0>;
-	clock-names = "baud", "xtal", "pclk";
+	compatible = "amlogic,meson8b-uart";
+	clocks = <&xtal>, <&clkc CLKID_UART0>, <&clkc CLKID_CLK81>;
+	clock-names = "xtal", "pclk", "baud";
 };
 
 &uart_B {
-	compatible = "amlogic,meson8b-uart", "amlogic,meson-uart";
-	clocks = <&clkc CLKID_CLK81>, <&xtal>, <&clkc CLKID_UART1>;
-	clock-names = "baud", "xtal", "pclk";
+	compatible = "amlogic,meson8b-uart";
+	clocks = <&xtal>, <&clkc CLKID_UART0>, <&clkc CLKID_CLK81>;
+	clock-names = "xtal", "pclk", "baud";
 };
 
 &uart_C {
-	compatible = "amlogic,meson8b-uart", "amlogic,meson-uart";
-	clocks = <&clkc CLKID_CLK81>, <&xtal>, <&clkc CLKID_UART2>;
-	clock-names = "baud", "xtal", "pclk";
+	compatible = "amlogic,meson8b-uart";
+	clocks = <&xtal>, <&clkc CLKID_UART0>, <&clkc CLKID_CLK81>;
+	clock-names = "xtal", "pclk", "baud";
 };
 
 &usb0 {
diff --git a/arch/arm/boot/dts/milbeaut-m10v.dtsi b/arch/arm/boot/dts/milbeaut-m10v.dtsi
index aa7c6caeb750..75f0c0af2270 100644
--- a/arch/arm/boot/dts/milbeaut-m10v.dtsi
+++ b/arch/arm/boot/dts/milbeaut-m10v.dtsi
@@ -65,10 +65,18 @@
 			      <0x1d002000 0x1000>; /* CPU I/f base and size */
 		};
 
+		clk: clock-ctrl@1d021000 {
+			compatible = "socionext,milbeaut-m10v-ccu";
+			#clock-cells = <1>;
+			reg = <0x1d021000 0x1000>;
+			clocks = <&uclk40xi>;
+		};
+
 		timer@1e000050 { /* 32-bit Reload Timers */
 			compatible = "socionext,milbeaut-timer";
 			reg = <0x1e000050 0x20>;
 			interrupts = <0 91 4>;
+			clocks = <&clk 4>;
 		};
 
 		uart1: serial@1e700010 { /* PE4, PE5 */
@@ -77,6 +85,7 @@
 			reg = <0x1e700010 0x10>;
 			interrupts = <0 141 0x4>, <0 149 0x4>;
 			interrupt-names = "rx", "tx";
+			clocks = <&clk 2>;
 		};
 
 	};
diff --git a/arch/arm/boot/dts/mmp2.dtsi b/arch/arm/boot/dts/mmp2.dtsi
index 46984d4c5224..987d792f67ea 100644
--- a/arch/arm/boot/dts/mmp2.dtsi
+++ b/arch/arm/boot/dts/mmp2.dtsi
@@ -275,7 +275,9 @@
 				compatible = "marvell,pdma-1.0";
 				reg = <0xd4000000 0x10000>;
 				interrupts = <48>;
+				/* For backwards compatibility: */
 				#dma-channels = <16>;
+				dma-channels = <16>;
 				status = "disabled";
 			};
 
diff --git a/arch/arm/boot/dts/motorola-mapphone-common.dtsi b/arch/arm/boot/dts/motorola-mapphone-common.dtsi
index a4423ff0df39..c7a1f3ffc48c 100644
--- a/arch/arm/boot/dts/motorola-mapphone-common.dtsi
+++ b/arch/arm/boot/dts/motorola-mapphone-common.dtsi
@@ -310,7 +310,7 @@
 	#address-cells = <1>;
 	#size-cells = <0>;
 	wlcore: wlcore@2 {
-		compatible = "ti,wl1285", "ti,wl1283";
+		compatible = "ti,wl1285";
 		reg = <2>;
 		/* gpio_100 with gpmc_wait2 pad as wakeirq */
 		interrupts-extended = <&gpio4 4 IRQ_TYPE_LEVEL_HIGH>,
diff --git a/arch/arm/boot/dts/moxart-uc7112lx.dts b/arch/arm/boot/dts/moxart-uc7112lx.dts
index eb5291b0ee3a..e07b807b4cec 100644
--- a/arch/arm/boot/dts/moxart-uc7112lx.dts
+++ b/arch/arm/boot/dts/moxart-uc7112lx.dts
@@ -79,7 +79,7 @@
 	clocks = <&ref12>;
 };
 
-&sdhci {
+&mmc {
 	status = "okay";
 };
 
diff --git a/arch/arm/boot/dts/moxart.dtsi b/arch/arm/boot/dts/moxart.dtsi
index f5f070a87482..764832ddfa78 100644
--- a/arch/arm/boot/dts/moxart.dtsi
+++ b/arch/arm/boot/dts/moxart.dtsi
@@ -93,8 +93,8 @@
 			clock-names = "PCLK";
 		};
 
-		sdhci: sdhci@98e00000 {
-			compatible = "moxa,moxart-sdhci";
+		mmc: mmc@98e00000 {
+			compatible = "moxa,moxart-mmc";
 			reg = <0x98e00000 0x5C>;
 			interrupts = <5 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&clk_apb>;
diff --git a/arch/arm/boot/dts/mstar-infinity.dtsi b/arch/arm/boot/dts/mstar-infinity.dtsi
index 0bee517797f4..441a917b88ba 100644
--- a/arch/arm/boot/dts/mstar-infinity.dtsi
+++ b/arch/arm/boot/dts/mstar-infinity.dtsi
@@ -8,6 +8,40 @@
 
 #include <dt-bindings/gpio/msc313-gpio.h>
 
+/ {
+	cpu0_opp_table: opp_table0 {
+		compatible = "operating-points-v2";
+		opp-shared;
+
+		opp-240000000 {
+			opp-hz = /bits/ 64 <240000000>;
+			opp-microvolt = <1000000>;
+			clock-latency-ns = <300000>;
+		};
+
+		opp-400000000 {
+			opp-hz = /bits/ 64 <400000000>;
+			opp-microvolt = <1000000>;
+			clock-latency-ns = <300000>;
+		};
+		opp-600000000 {
+			opp-hz = /bits/ 64 <600000000>;
+			opp-microvolt = <1000000>;
+			clock-latency-ns = <300000>;
+		};
+
+		opp-800000000 {
+			opp-hz = /bits/ 64 <800000000>;
+			opp-microvolt = <1000000>;
+			clock-latency-ns = <300000>;
+		};
+	};
+};
+
+&cpu0 {
+	operating-points-v2 = <&cpu0_opp_table>;
+};
+
 &imi {
 	reg = <0xa0000000 0x16000>;
 };
diff --git a/arch/arm/boot/dts/mstar-infinity2m-ssd201-som2d01.dtsi b/arch/arm/boot/dts/mstar-infinity2m-ssd201-som2d01.dtsi
new file mode 100644
index 000000000000..34df472fed71
--- /dev/null
+++ b/arch/arm/boot/dts/mstar-infinity2m-ssd201-som2d01.dtsi
@@ -0,0 +1,20 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2021 thingy.jp.
+ * Author: Daniel Palmer <daniel@thingy.jp>
+ * Author: Romain Perier <romain.perier@gmail.com>
+ */
+
+/ {
+	reg_vcc_dram: regulator-vcc-dram {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_dram";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-boot-on;
+	};
+};
+
+&pm_uart {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/mstar-infinity2m-ssd202d-100ask-dongshanpione.dts b/arch/arm/boot/dts/mstar-infinity2m-ssd202d-100ask-dongshanpione.dts
new file mode 100644
index 000000000000..f25a04c98ccb
--- /dev/null
+++ b/arch/arm/boot/dts/mstar-infinity2m-ssd202d-100ask-dongshanpione.dts
@@ -0,0 +1,25 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (c) 2021 thingy.jp.
+ * Author: Daniel Palmer <daniel@thingy.jp>
+ */
+
+/dts-v1/;
+#include "mstar-infinity2m-ssd202d.dtsi"
+
+/ {
+	model = "DongShanPi One";
+	compatible = "100ask,dongshanpione", "mstar,infinity2m";
+
+	aliases {
+		serial0 = &pm_uart;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
+
+&pm_uart {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/mstar-infinity2m-ssd202d-miyoo-mini.dts b/arch/arm/boot/dts/mstar-infinity2m-ssd202d-miyoo-mini.dts
new file mode 100644
index 000000000000..1bbbf47132dc
--- /dev/null
+++ b/arch/arm/boot/dts/mstar-infinity2m-ssd202d-miyoo-mini.dts
@@ -0,0 +1,25 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (c) 2021 thingy.jp.
+ * Author: Daniel Palmer <daniel@thingy.jp>
+ */
+
+/dts-v1/;
+#include "mstar-infinity2m-ssd202d.dtsi"
+
+/ {
+	model = "Miyoo Mini";
+	compatible = "miyoo,miyoo-mini", "mstar,infinity2m";
+
+	aliases {
+		serial0 = &pm_uart;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
+
+&pm_uart {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/mstar-infinity2m-ssd202d-wirelesstag-ido-sbc2d06-v1b-22w.dts b/arch/arm/boot/dts/mstar-infinity2m-ssd202d-wirelesstag-ido-sbc2d06-v1b-22w.dts
new file mode 100644
index 000000000000..b15c40762bc0
--- /dev/null
+++ b/arch/arm/boot/dts/mstar-infinity2m-ssd202d-wirelesstag-ido-sbc2d06-v1b-22w.dts
@@ -0,0 +1,23 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2021 thingy.jp.
+ * Author: Daniel Palmer <daniel@thingy.jp>
+ * Author: Romain Perier <romain.perier@gmail.com>
+ */
+
+/dts-v1/;
+#include "mstar-infinity2m-ssd202d-wirelesstag-ido-som2d01.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "Wireless Tag IDO-SBC2D06-1VB-22W";
+	compatible = "wirelesstag,ido-sbc2d06-v1b-22w", "mstar,infinity2m";
+
+	leds {
+		compatible = "gpio-leds";
+		sys_led {
+			gpios = <&gpio SSD20XD_GPIO_GPIO85 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/mstar-infinity2m-ssd202d-wirelesstag-ido-som2d01.dtsi b/arch/arm/boot/dts/mstar-infinity2m-ssd202d-wirelesstag-ido-som2d01.dtsi
new file mode 100644
index 000000000000..d877aff85033
--- /dev/null
+++ b/arch/arm/boot/dts/mstar-infinity2m-ssd202d-wirelesstag-ido-som2d01.dtsi
@@ -0,0 +1,28 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) 2021 thingy.jp.
+ * Author: Daniel Palmer <daniel@thingy.jp>
+ * Author: Romain Perier <romain.perier@gmail.com>
+ */
+
+/dts-v1/;
+#include "mstar-infinity2m-ssd202d.dtsi"
+#include "mstar-infinity2m-ssd201-som2d01.dtsi"
+
+/ {
+	model = "Wireless Tag IDO-SOM2D01 (SSD202D)";
+	compatible = "wirelesstag,ido-som2d01", "mstar,infinity2m";
+
+	aliases {
+		serial0 = &pm_uart;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
+
+&reg_vcc_dram {
+	regulator-min-microvolt = <1500000>;
+	regulator-max-microvolt = <1500000>;
+};
diff --git a/arch/arm/boot/dts/mstar-infinity2m-ssd20xd.dtsi b/arch/arm/boot/dts/mstar-infinity2m-ssd20xd.dtsi
index 7a5e28b33f96..6f067da61ba3 100644
--- a/arch/arm/boot/dts/mstar-infinity2m-ssd20xd.dtsi
+++ b/arch/arm/boot/dts/mstar-infinity2m-ssd20xd.dtsi
@@ -6,6 +6,11 @@
 
 #include "mstar-infinity2m.dtsi"
 
+&gpio {
+	compatible = "sstar,ssd20xd-gpio";
+	status = "okay";
+};
+
 &smpctrl {
 	compatible = "sstar,ssd201-smpctrl", "mstar,smpctrl";
 	status = "okay";
diff --git a/arch/arm/boot/dts/mstar-infinity2m.dtsi b/arch/arm/boot/dts/mstar-infinity2m.dtsi
index 6d4d1d224e96..1b485efd7156 100644
--- a/arch/arm/boot/dts/mstar-infinity2m.dtsi
+++ b/arch/arm/boot/dts/mstar-infinity2m.dtsi
@@ -6,11 +6,28 @@
 
 #include "mstar-infinity.dtsi"
 
+&cpu0_opp_table {
+		opp-1000000000 {
+			opp-hz = /bits/ 64 <1000000000>;
+			opp-microvolt = <1000000>;
+			clock-latency-ns = <300000>;
+		};
+
+		opp-1200000000 {
+			opp-hz = /bits/ 64 <1200000000>;
+			opp-microvolt = <1000000>;
+			clock-latency-ns = <300000>;
+		};
+};
+
 &cpus {
 	cpu1: cpu@1 {
 		device_type = "cpu";
 		compatible = "arm,cortex-a7";
+		operating-points-v2 = <&cpu0_opp_table>;
 		reg = <0x1>;
+		clocks = <&cpupll>;
+		clock-names = "cpuclk";
 	};
 };
 
diff --git a/arch/arm/boot/dts/mstar-infinity3.dtsi b/arch/arm/boot/dts/mstar-infinity3.dtsi
index 9857e2a9934d..a56cf29e5d82 100644
--- a/arch/arm/boot/dts/mstar-infinity3.dtsi
+++ b/arch/arm/boot/dts/mstar-infinity3.dtsi
@@ -6,6 +6,64 @@
 
 #include "mstar-infinity.dtsi"
 
+&cpu0_opp_table {
+	opp-1008000000 {
+		opp-hz = /bits/ 64 <1008000000>;
+		opp-microvolt = <1000000>;
+		clock-latency-ns = <300000>;
+	};
+
+	// overclock frequencies below, shown to work fine up to 1.3 GHz
+	opp-108000000 {
+		opp-hz = /bits/ 64 <1080000000>;
+		opp-microvolt = <1000000>;
+		clock-latency-ns = <300000>;
+		turbo-mode;
+	};
+
+	opp-1188000000 {
+		opp-hz = /bits/ 64 <1188000000>;
+		opp-microvolt = <1000000>;
+		clock-latency-ns = <300000>;
+		turbo-mode;
+	};
+
+	opp-1296000000 {
+		opp-hz = /bits/ 64 <1296000000>;
+		opp-microvolt = <1000000>;
+		clock-latency-ns = <300000>;
+		turbo-mode;
+	};
+
+	opp-1350000000 {
+		opp-hz = /bits/ 64 <1350000000>;
+		opp-microvolt = <1000000>;
+		clock-latency-ns = <300000>;
+		turbo-mode;
+	};
+
+	opp-1404000000 {
+		opp-hz = /bits/ 64 <1404000000>;
+		opp-microvolt = <1000000>;
+		clock-latency-ns = <300000>;
+		turbo-mode;
+	};
+
+	opp-1458000000 {
+		opp-hz = /bits/ 64 <1458000000>;
+		opp-microvolt = <1000000>;
+		clock-latency-ns = <300000>;
+		turbo-mode;
+	};
+
+	opp-1512000000 {
+		opp-hz = /bits/ 64 <1512000000>;
+		opp-microvolt = <1000000>;
+		clock-latency-ns = <300000>;
+		turbo-mode;
+	};
+};
+
 &imi {
 	reg = <0xa0000000 0x20000>;
 };
diff --git a/arch/arm/boot/dts/mstar-v7.dtsi b/arch/arm/boot/dts/mstar-v7.dtsi
index 89ebfe4f29da..c26ba9b7b6dd 100644
--- a/arch/arm/boot/dts/mstar-v7.dtsi
+++ b/arch/arm/boot/dts/mstar-v7.dtsi
@@ -21,6 +21,8 @@
 			device_type = "cpu";
 			compatible = "arm,cortex-a7";
 			reg = <0x0>;
+			clocks = <&cpupll>;
+			clock-names = "cpuclk";
 		};
 	};
 
@@ -155,6 +157,13 @@
 				clocks = <&xtal>;
 			};
 
+			cpupll: cpupll@206400 {
+				compatible = "mstar,msc313-cpupll";
+				reg = <0x206400 0x200>;
+				#clock-cells = <0>;
+				clocks = <&mpll MSTAR_MSC313_MPLL_DIV2>;
+			};
+
 			gpio: gpio@207800 {
 				#gpio-cells = <2>;
 				reg = <0x207800 0x200>;
diff --git a/arch/arm/boot/dts/mt2701.dtsi b/arch/arm/boot/dts/mt2701.dtsi
index 4776f85d6d5b..b8eba3ba153c 100644
--- a/arch/arm/boot/dts/mt2701.dtsi
+++ b/arch/arm/boot/dts/mt2701.dtsi
@@ -427,9 +427,9 @@
 
 		afe: audio-controller {
 			compatible = "mediatek,mt2701-audio";
-			interrupts =  <GIC_SPI 104 IRQ_TYPE_LEVEL_LOW>,
+			interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_LOW>,
 				      <GIC_SPI 132 IRQ_TYPE_LEVEL_LOW>;
-			interrupt-names	= "afe", "asys";
+			interrupt-names = "afe", "asys";
 			power-domains = <&scpsys MT2701_POWER_DOMAIN_IFR_MSC>;
 
 			clocks = <&infracfg CLK_INFRA_AUDIO>,
@@ -559,12 +559,11 @@
 		compatible = "mediatek,mt2701-jpgdec";
 		reg = <0 0x15004000 0 0x1000>;
 		interrupts = <GIC_SPI 143 IRQ_TYPE_LEVEL_LOW>;
-		clocks =  <&imgsys CLK_IMG_JPGDEC_SMI>,
+		clocks = <&imgsys CLK_IMG_JPGDEC_SMI>,
 			  <&imgsys CLK_IMG_JPGDEC>;
 		clock-names = "jpgdec-smi",
 			      "jpgdec";
 		power-domains = <&scpsys MT2701_POWER_DOMAIN_ISP>;
-		mediatek,larb = <&larb2>;
 		iommus = <&iommu MT2701_M4U_PORT_JPGDEC_WDMA>,
 			 <&iommu MT2701_M4U_PORT_JPGDEC_BSDMA>;
 	};
@@ -574,10 +573,9 @@
 			     "mediatek,mtk-jpgenc";
 		reg = <0 0x1500a000 0 0x1000>;
 		interrupts = <GIC_SPI 141 IRQ_TYPE_LEVEL_LOW>;
-		clocks =  <&imgsys CLK_IMG_VENC>;
+		clocks = <&imgsys CLK_IMG_VENC>;
 		clock-names = "jpgenc";
 		power-domains = <&scpsys MT2701_POWER_DOMAIN_ISP>;
-		mediatek,larb = <&larb2>;
 		iommus = <&iommu MT2701_M4U_PORT_JPGENC_RDMA>,
 			 <&iommu MT2701_M4U_PORT_JPGENC_BSDMA>;
 	};
diff --git a/arch/arm/boot/dts/mt6582-prestigio-pmt5008-3g.dts b/arch/arm/boot/dts/mt6582-prestigio-pmt5008-3g.dts
new file mode 100644
index 000000000000..b057e037f940
--- /dev/null
+++ b/arch/arm/boot/dts/mt6582-prestigio-pmt5008-3g.dts
@@ -0,0 +1,43 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (c) 2021 Maxim Kutnij <gtk3@inbox.ru>
+ */
+
+/dts-v1/;
+#include "mt6582.dtsi"
+
+/ {
+	model = "Prestigio PMT5008 3G";
+	compatible = "prestigio,pmt5008-3g", "mediatek,mt6582";
+
+	aliases {
+		bootargs = "console=ttyS0,921600n8 earlyprintk";
+		serial0 = &uart0;
+		serial3 = &uart3;
+	};
+
+	chosen {
+		stdout-path = "serial0:921600n8";
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x80000000 0x40000000>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&uart3 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/mt6582.dtsi b/arch/arm/boot/dts/mt6582.dtsi
new file mode 100644
index 000000000000..4263371784cd
--- /dev/null
+++ b/arch/arm/boot/dts/mt6582.dtsi
@@ -0,0 +1,128 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (c) 2021 Maxim Kutnij <gtk3@inbox.ru>
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	compatible = "mediatek,mt6582";
+	interrupt-parent = <&sysirq>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x0>;
+		};
+		cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x1>;
+		};
+		cpu@2 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x2>;
+		};
+		cpu@3 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x3>;
+		};
+	};
+
+	system_clk: dummy13m {
+		compatible = "fixed-clock";
+		clock-frequency = <13000000>;
+		#clock-cells = <0>;
+	};
+
+	rtc_clk: dummy32k {
+		compatible = "fixed-clock";
+		clock-frequency = <32000>;
+		#clock-cells = <0>;
+	};
+
+	uart_clk: dummy26m {
+		compatible = "fixed-clock";
+		clock-frequency = <26000000>;
+		#clock-cells = <0>;
+	};
+
+	timer: timer@11008000 {
+		compatible = "mediatek,mt6577-timer";
+		reg = <0x10008000 0x80>;
+		interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_LOW>;
+		clocks = <&system_clk>, <&rtc_clk>;
+		clock-names = "system-clk", "rtc-clk";
+	};
+
+	sysirq: interrupt-controller@10200100 {
+		compatible = "mediatek,mt6582-sysirq",
+			     "mediatek,mt6577-sysirq";
+		interrupt-controller;
+		#interrupt-cells = <3>;
+		interrupt-parent = <&gic>;
+		reg = <0x10200100 0x1c>;
+	};
+
+	gic: interrupt-controller@10211000 {
+		compatible = "arm,cortex-a7-gic";
+		interrupt-controller;
+		#interrupt-cells = <3>;
+		interrupt-parent = <&gic>;
+		reg = <0x10211000 0x1000>,
+		      <0x10212000 0x2000>,
+		      <0x10214000 0x2000>,
+		      <0x10216000 0x2000>;
+	};
+
+	uart0: serial@11002000 {
+		compatible = "mediatek,mt6582-uart",
+			     "mediatek,mt6577-uart";
+		reg = <0x11002000 0x400>;
+		interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_LOW>;
+		clocks = <&uart_clk>;
+		status = "disabled";
+	};
+
+	uart1: serial@11003000 {
+		compatible = "mediatek,mt6582-uart",
+			     "mediatek,mt6577-uart";
+		reg = <0x11003000 0x400>;
+		interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_LOW>;
+		clocks = <&uart_clk>;
+		status = "disabled";
+	};
+
+	uart2: serial@11004000 {
+		compatible = "mediatek,mt6582-uart",
+			     "mediatek,mt6577-uart";
+		reg = <0x11004000 0x400>;
+		interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_LOW>;
+		clocks = <&uart_clk>;
+		status = "disabled";
+	};
+
+	uart3: serial@11005000 {
+		compatible = "mediatek,mt6582-uart",
+			     "mediatek,mt6577-uart";
+		reg = <0x11005000 0x400>;
+		interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_LOW>;
+		clocks = <&uart_clk>;
+		status = "disabled";
+	};
+
+	watchdog: watchdog@10007000 {
+		compatible = "mediatek,mt6582-wdt",
+			     "mediatek,mt6589-wdt";
+		reg = <0x10007000 0x100>;
+	};
+};
diff --git a/arch/arm/boot/dts/mt6589-fairphone-fp1.dts b/arch/arm/boot/dts/mt6589-fairphone-fp1.dts
new file mode 100644
index 000000000000..c952347981de
--- /dev/null
+++ b/arch/arm/boot/dts/mt6589-fairphone-fp1.dts
@@ -0,0 +1,30 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, Luca Weiss <luca@z3ntu.xyz>
+ */
+
+/dts-v1/;
+#include "mt6589.dtsi"
+
+/ {
+	model = "Fairphone 1";
+	compatible = "fairphone,fp1", "mediatek,mt6589";
+
+	chosen {
+		stdout-path = &uart3;
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x80000000 0x40000000>;
+	};
+};
+
+&cpus {
+	/* SMP is not stable on this board, makes the kernel panic */
+	/delete-property/ enable-method;
+};
+
+&uart3 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/mt6589.dtsi b/arch/arm/boot/dts/mt6589.dtsi
index 70df00a7bb26..c6babc8ad2ba 100644
--- a/arch/arm/boot/dts/mt6589.dtsi
+++ b/arch/arm/boot/dts/mt6589.dtsi
@@ -14,7 +14,7 @@
 	compatible = "mediatek,mt6589";
 	interrupt-parent = <&sysirq>;
 
-	cpus {
+	cpus: cpus {
 		#address-cells = <1>;
 		#size-cells = <0>;
 		enable-method = "mediatek,mt6589-smp";
diff --git a/arch/arm/boot/dts/mt7623.dtsi b/arch/arm/boot/dts/mt7623.dtsi
index f4848362b3be..25d31e40a553 100644
--- a/arch/arm/boot/dts/mt7623.dtsi
+++ b/arch/arm/boot/dts/mt7623.dtsi
@@ -241,7 +241,7 @@
 	};
 
 	pericfg: syscon@10003000 {
-		compatible =  "mediatek,mt7623-pericfg",
+		compatible = "mediatek,mt7623-pericfg",
 			      "mediatek,mt2701-pericfg",
 			      "syscon";
 		reg = <0 0x10003000 0 0x1000>;
@@ -628,9 +628,9 @@
 		afe: audio-controller {
 			compatible = "mediatek,mt7623-audio",
 				     "mediatek,mt2701-audio";
-			interrupts =  <GIC_SPI 104 IRQ_TYPE_LEVEL_LOW>,
+			interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_LOW>,
 				      <GIC_SPI 132 IRQ_TYPE_LEVEL_LOW>;
-			interrupt-names	= "afe", "asys";
+			interrupt-names = "afe", "asys";
 			power-domains = <&scpsys MT2701_POWER_DOMAIN_IFR_MSC>;
 
 			clocks = <&infracfg CLK_INFRA_AUDIO>,
diff --git a/arch/arm/boot/dts/mt7623a-rfb-emmc.dts b/arch/arm/boot/dts/mt7623a-rfb-emmc.dts
index 13c86936d1c8..e8b4b6d30d19 100644
--- a/arch/arm/boot/dts/mt7623a-rfb-emmc.dts
+++ b/arch/arm/boot/dts/mt7623a-rfb-emmc.dts
@@ -45,13 +45,13 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&key_pins_a>;
 
-		factory {
+		button-factory {
 			label = "factory";
 			linux,code = <BTN_0>;
 			gpios = <&pio 256 GPIO_ACTIVE_LOW>;
 		};
 
-		wps {
+		button-wps {
 			label = "wps";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&pio 257 GPIO_ACTIVE_HIGH>;
diff --git a/arch/arm/boot/dts/mt7623a-rfb-nand.dts b/arch/arm/boot/dts/mt7623a-rfb-nand.dts
index 88d8f0b2f4c2..61f5da68d4b0 100644
--- a/arch/arm/boot/dts/mt7623a-rfb-nand.dts
+++ b/arch/arm/boot/dts/mt7623a-rfb-nand.dts
@@ -45,13 +45,13 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&key_pins_a>;
 
-		factory {
+		button-factory {
 			label = "factory";
 			linux,code = <BTN_0>;
 			gpios = <&pio 256 GPIO_ACTIVE_LOW>;
 		};
 
-		wps {
+		button-wps {
 			label = "wps";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&pio 257 GPIO_ACTIVE_HIGH>;
diff --git a/arch/arm/boot/dts/mt7623n-bananapi-bpi-r2.dts b/arch/arm/boot/dts/mt7623n-bananapi-bpi-r2.dts
index 027c1b0c6a98..5008115d2494 100644
--- a/arch/arm/boot/dts/mt7623n-bananapi-bpi-r2.dts
+++ b/arch/arm/boot/dts/mt7623n-bananapi-bpi-r2.dts
@@ -91,13 +91,13 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&key_pins_a>;
 
-		factory {
+		button-factory {
 			label = "factory";
 			linux,code = <BTN_0>;
 			gpios = <&pio 256 GPIO_ACTIVE_LOW>;
 		};
 
-		wps {
+		button-wps {
 			label = "wps";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&pio 257 GPIO_ACTIVE_HIGH>;
diff --git a/arch/arm/boot/dts/mt7623n-rfb-emmc.dts b/arch/arm/boot/dts/mt7623n-rfb-emmc.dts
index 1b9b9a8145a7..bf67a8e9be59 100644
--- a/arch/arm/boot/dts/mt7623n-rfb-emmc.dts
+++ b/arch/arm/boot/dts/mt7623n-rfb-emmc.dts
@@ -60,13 +60,13 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&key_pins_a>;
 
-		factory {
+		button-factory {
 			label = "factory";
 			linux,code = <BTN_0>;
 			gpios = <&pio 256 GPIO_ACTIVE_LOW>;
 		};
 
-		wps {
+		button-wps {
 			label = "wps";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&pio 257 GPIO_ACTIVE_HIGH>;
diff --git a/arch/arm/boot/dts/mt7623n.dtsi b/arch/arm/boot/dts/mt7623n.dtsi
index bcb0846e29fd..3adab5cd1fef 100644
--- a/arch/arm/boot/dts/mt7623n.dtsi
+++ b/arch/arm/boot/dts/mt7623n.dtsi
@@ -121,7 +121,6 @@
 		clock-names = "jpgdec-smi",
 			      "jpgdec";
 		power-domains = <&scpsys MT2701_POWER_DOMAIN_ISP>;
-		mediatek,larb = <&larb2>;
 		iommus = <&iommu MT2701_M4U_PORT_JPGDEC_WDMA>,
 			 <&iommu MT2701_M4U_PORT_JPGDEC_BSDMA>;
 	};
@@ -144,7 +143,6 @@
 		interrupts = <GIC_SPI 153 IRQ_TYPE_LEVEL_LOW>;
 		clocks = <&mmsys CLK_MM_DISP_OVL>;
 		iommus = <&iommu MT2701_M4U_PORT_DISP_OVL_0>;
-		mediatek,larb = <&larb0>;
 	};
 
 	rdma0: rdma@14008000 {
@@ -154,7 +152,6 @@
 		interrupts = <GIC_SPI 152 IRQ_TYPE_LEVEL_LOW>;
 		clocks = <&mmsys CLK_MM_DISP_RDMA>;
 		iommus = <&iommu MT2701_M4U_PORT_DISP_RDMA>;
-		mediatek,larb = <&larb0>;
 	};
 
 	wdma@14009000 {
@@ -164,7 +161,6 @@
 		interrupts = <GIC_SPI 154 IRQ_TYPE_LEVEL_LOW>;
 		clocks = <&mmsys CLK_MM_DISP_WDMA>;
 		iommus = <&iommu MT2701_M4U_PORT_DISP_WDMA>;
-		mediatek,larb = <&larb0>;
 	};
 
 	bls: pwm@1400a000 {
@@ -215,7 +211,6 @@
 		interrupts = <GIC_SPI 164 IRQ_TYPE_LEVEL_LOW>;
 		clocks = <&mmsys CLK_MM_DISP_RDMA1>;
 		iommus = <&iommu MT2701_M4U_PORT_DISP_RDMA1>;
-		mediatek,larb = <&larb0>;
 	};
 
 	dpi0: dpi@14014000 {
diff --git a/arch/arm/boot/dts/mt7629-rfb.dts b/arch/arm/boot/dts/mt7629-rfb.dts
index eb536cbebd9b..84e14bee7235 100644
--- a/arch/arm/boot/dts/mt7629-rfb.dts
+++ b/arch/arm/boot/dts/mt7629-rfb.dts
@@ -23,13 +23,13 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		reset {
+		button-reset {
 			label = "factory";
 			linux,code = <KEY_RESTART>;
 			gpios = <&pio 60 GPIO_ACTIVE_LOW>;
 		};
 
-		wps {
+		button-wps {
 			label = "wps";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&pio 58 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/mxs-pinfunc.h b/arch/arm/boot/dts/mxs-pinfunc.h
index c6da987b20cb..31297abcbc71 100644
--- a/arch/arm/boot/dts/mxs-pinfunc.h
+++ b/arch/arm/boot/dts/mxs-pinfunc.h
@@ -1,14 +1,8 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * Header providing constants for i.MX28 pinctrl bindings.
  *
  * Copyright (C) 2013 Lothar Waßmann <LW@KARO-electronics.de>
- *
- * The code contained herein is licensed under the GNU General Public
- * License. You may obtain a copy of the GNU General Public License
- * Version 2 at the following locations:
- *
- * http://www.opensource.org/licenses/gpl-license.html
- * http://www.gnu.org/copyleft/gpl.html
  */
 
 #ifndef __DT_BINDINGS_MXS_PINCTRL_H__
diff --git a/arch/arm/boot/dts/nspire-classic.dtsi b/arch/arm/boot/dts/nspire-classic.dtsi
index 41744cc2bc72..01e1bb7c3c6c 100644
--- a/arch/arm/boot/dts/nspire-classic.dtsi
+++ b/arch/arm/boot/dts/nspire-classic.dtsi
@@ -17,7 +17,7 @@
 
 &fast_timer {
 	/* compatible = "lsi,zevio-timer"; */
-	reg = <0x90010000 0x1000>, <0x900A0010 0x8>;
+	reg = <0x90010000 0x1000>, <0x900a0010 0x8>;
 };
 
 &uart {
@@ -30,12 +30,12 @@
 
 &timer0 {
 	/* compatible = "lsi,zevio-timer"; */
-	reg = <0x900C0000 0x1000>, <0x900A0018 0x8>;
+	reg = <0x900c0000 0x1000>, <0x900a0018 0x8>;
 };
 
 &timer1 {
 	compatible = "lsi,zevio-timer";
-	reg = <0x900D0000 0x1000>, <0x900A0020 0x8>;
+	reg = <0x900d0000 0x1000>, <0x900a0020 0x8>;
 };
 
 &keypad {
@@ -66,10 +66,10 @@
 		#address-cells = <1>;
 		#size-cells = <1>;
 
-		intc: interrupt-controller@DC000000 {
+		intc: interrupt-controller@dc000000 {
 			compatible = "lsi,zevio-intc";
 			interrupt-controller;
-			reg = <0xDC000000 0x1000>;
+			reg = <0xdc000000 0x1000>;
 			#interrupt-cells = <1>;
 		};
 	};
diff --git a/arch/arm/boot/dts/nspire-cx.dts b/arch/arm/boot/dts/nspire-cx.dts
index 0c16b04e2744..590b7dff6ae5 100644
--- a/arch/arm/boot/dts/nspire-cx.dts
+++ b/arch/arm/boot/dts/nspire-cx.dts
@@ -92,10 +92,10 @@
 		#address-cells = <1>;
 		#size-cells = <1>;
 
-		intc: interrupt-controller@DC000000 {
+		intc: interrupt-controller@dc000000 {
 			compatible = "arm,pl190-vic";
 			interrupt-controller;
-			reg = <0xDC000000 0x1000>;
+			reg = <0xdc000000 0x1000>;
 			#interrupt-cells = <1>;
 		};
 
diff --git a/arch/arm/boot/dts/nspire.dtsi b/arch/arm/boot/dts/nspire.dtsi
index 90e033d9141f..bb240e6a3a6f 100644
--- a/arch/arm/boot/dts/nspire.dtsi
+++ b/arch/arm/boot/dts/nspire.dtsi
@@ -20,9 +20,9 @@
 		reg = <0x00000000 0x80000>;
 	};
 
-	sram: sram@A4000000 {
+	sram: sram@a4000000 {
 		device = "memory";
-		reg = <0xA4000000 0x20000>;
+		reg = <0xa4000000 0x20000>;
 	};
 
 	timer_clk: timer_clk {
@@ -33,12 +33,12 @@
 
 	base_clk: base_clk {
 		#clock-cells = <0>;
-		reg = <0x900B0024 0x4>;
+		reg = <0x900b0024 0x4>;
 	};
 
 	ahb_clk: ahb_clk {
 		#clock-cells = <0>;
-		reg = <0x900B0024 0x4>;
+		reg = <0x900b0024 0x4>;
 		clocks = <&base_clk>;
 	};
 
@@ -71,28 +71,28 @@
 		#size-cells = <1>;
 		ranges;
 
-		spi: spi@A9000000 {
-			reg = <0xA9000000 0x1000>;
+		spi: spi@a9000000 {
+			reg = <0xa9000000 0x1000>;
 		};
 
-		usb0: usb@B0000000 {
+		usb0: usb@b0000000 {
 			compatible = "lsi,zevio-usb";
-			reg = <0xB0000000 0x1000>;
+			reg = <0xb0000000 0x1000>;
 			interrupts = <8>;
 
 			usb-phy = <&usb_phy>;
 			vbus-supply = <&vbus_reg>;
 		};
 
-		usb1: usb@B4000000 {
-			reg = <0xB4000000 0x1000>;
+		usb1: usb@b4000000 {
+			reg = <0xb4000000 0x1000>;
 			interrupts = <9>;
 			status = "disabled";
 		};
 
-		lcd: lcd@C0000000 {
+		lcd: lcd@c0000000 {
 			compatible = "arm,pl111", "arm,primecell";
-			reg = <0xC0000000 0x1000>;
+			reg = <0xc0000000 0x1000>;
 			interrupts = <21>;
 
 			/*
@@ -105,17 +105,17 @@
 			clock-names = "clcdclk", "apb_pclk";
 		};
 
-		adc: adc@C4000000 {
-			reg = <0xC4000000 0x1000>;
+		adc: adc@c4000000 {
+			reg = <0xc4000000 0x1000>;
 			interrupts = <11>;
 		};
 
-		tdes: crypto@C8010000 {
-			reg = <0xC8010000 0x1000>;
+		tdes: crypto@c8010000 {
+			reg = <0xc8010000 0x1000>;
 		};
 
-		sha256: crypto@CC000000 {
-			reg = <0xCC000000 0x1000>;
+		sha256: crypto@cc000000 {
+			reg = <0xcc000000 0x1000>;
 		};
 
 		apb@90000000 {
@@ -143,16 +143,16 @@
 				interrupts = <1>;
 			};
 
-			timer0: timer@900C0000 {
-				reg = <0x900C0000 0x1000>;
+			timer0: timer@900c0000 {
+				reg = <0x900c0000 0x1000>;
 				clocks = <&timer_clk>, <&timer_clk>,
 					 <&timer_clk>;
 				clock-names = "timer0clk", "timer1clk",
 					      "apb_pclk";
 			};
 
-			timer1: timer@900D0000 {
-				reg = <0x900D0000 0x1000>;
+			timer1: timer@900d0000 {
+				reg = <0x900d0000 0x1000>;
 				interrupts = <19>;
 				clocks = <&timer_clk>, <&timer_clk>,
 					 <&timer_clk>;
@@ -171,18 +171,18 @@
 				interrupts = <4>;
 			};
 
-			misc: misc@900A0000 {
-				reg = <0x900A0000 0x1000>;
+			misc: misc@900a0000 {
+				reg = <0x900a0000 0x1000>;
 			};
 
-			pwr: pwr@900B0000 {
-				reg = <0x900B0000 0x1000>;
+			pwr: pwr@900b0000 {
+				reg = <0x900b0000 0x1000>;
 				interrupts = <15>;
 			};
 
-			keypad: input@900E0000 {
+			keypad: input@900e0000 {
 				compatible = "ti,nspire-keypad";
-				reg = <0x900E0000 0x1000>;
+				reg = <0x900e0000 0x1000>;
 				interrupts = <16>;
 
 				scan-interval = <1000>;
@@ -191,8 +191,8 @@
 				clocks = <&apb_pclk>;
 			};
 
-			contrast: contrast@900F0000 {
-				reg = <0x900F0000 0x1000>;
+			contrast: contrast@900f0000 {
+				reg = <0x900f0000 0x1000>;
 			};
 
 			led: led@90110000 {
diff --git a/arch/arm/boot/dts/nuvoton-common-npcm7xx.dtsi b/arch/arm/boot/dts/nuvoton-common-npcm7xx.dtsi
index 3696980a3da1..c7b5ef15b716 100644
--- a/arch/arm/boot/dts/nuvoton-common-npcm7xx.dtsi
+++ b/arch/arm/boot/dts/nuvoton-common-npcm7xx.dtsi
@@ -110,6 +110,7 @@
 			compatible = "nuvoton,npcm750-reset";
 			reg = <0xf0801000 0x70>;
 			#reset-cells = <2>;
+			nuvoton,sysgcr = <&gcr>;
 		};
 
 		clk: clock-controller@f0801000 {
@@ -128,7 +129,7 @@
 			interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "macirq";
 			ethernet = <0>;
-			clocks	= <&clk_rg1refck>, <&clk NPCM7XX_CLK_AHB>;
+			clocks = <&clk_rg1refck>, <&clk NPCM7XX_CLK_AHB>;
 			clock-names = "stmmaceth", "clk_gmac";
 			pinctrl-names = "default";
 			pinctrl-0 = <&rg1_pins
diff --git a/arch/arm/boot/dts/nuvoton-npcm730-gbs.dts b/arch/arm/boot/dts/nuvoton-npcm730-gbs.dts
index eb6eb21cb2a4..d10669fcd527 100644
--- a/arch/arm/boot/dts/nuvoton-npcm730-gbs.dts
+++ b/arch/arm/boot/dts/nuvoton-npcm730-gbs.dts
@@ -358,7 +358,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&spi0cs1_pins>;
 	status = "okay";
-	spi-nor@0 {
+	flash@0 {
 		compatible = "jedec,spi-nor";
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -406,7 +406,7 @@
 	pinctrl-0 = <&spi3_pins>, <&spi3cs1_pins>;
 	status = "okay";
 
-	spi-nor@0 {
+	flash@0 {
 		compatible = "jedec,spi-nor";
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -416,7 +416,7 @@
 		m25p,fast-read;
 		label = "pnor";
 	};
-	spi-nor@1 {
+	flash@1 {
 		compatible = "jedec,spi-nor";
 		#address-cells = <1>;
 		#size-cells = <1>;
diff --git a/arch/arm/boot/dts/nuvoton-npcm730-gsj.dts b/arch/arm/boot/dts/nuvoton-npcm730-gsj.dts
index d4ff49939a3d..491606c4f044 100644
--- a/arch/arm/boot/dts/nuvoton-npcm730-gsj.dts
+++ b/arch/arm/boot/dts/nuvoton-npcm730-gsj.dts
@@ -135,7 +135,7 @@
 	pinctrl-0 = <&spi0cs1_pins>;
 	status = "okay";
 
-	spi-nor@0 {
+	flash@0 {
 		compatible = "jedec,spi-nor";
 		#address-cells = <1>;
 		#size-cells = <1>;
diff --git a/arch/arm/boot/dts/nuvoton-npcm730-kudo.dts b/arch/arm/boot/dts/nuvoton-npcm730-kudo.dts
index 82a104b2a65f..a0c2d7652625 100644
--- a/arch/arm/boot/dts/nuvoton-npcm730-kudo.dts
+++ b/arch/arm/boot/dts/nuvoton-npcm730-kudo.dts
@@ -380,7 +380,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&spi0cs1_pins>;
 	status = "okay";
-	spi-nor@0 {
+	flash@0 {
 		compatible = "jedec,spi-nor";
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -415,7 +415,7 @@
 			};
 		};
 	};
-	spi-nor@1 {
+	flash@1 {
 		compatible = "jedec,spi-nor";
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -440,7 +440,7 @@
 
 &fiu3 {
 	pinctrl-0 = <&spi3_pins>;
-	spi-nor@0 {
+	flash@0 {
 		compatible = "jedec,spi-nor";
 		#address-cells = <1>;
 		#size-cells = <1>;
diff --git a/arch/arm/boot/dts/nuvoton-npcm750-evb.dts b/arch/arm/boot/dts/nuvoton-npcm750-evb.dts
index 0334641f8829..3dad32834e5e 100644
--- a/arch/arm/boot/dts/nuvoton-npcm750-evb.dts
+++ b/arch/arm/boot/dts/nuvoton-npcm750-evb.dts
@@ -67,7 +67,7 @@
 
 &fiu0 {
 	status = "okay";
-	spi-nor@0 {
+	flash@0 {
 		compatible = "jedec,spi-nor";
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -128,7 +128,7 @@
 &fiu3 {
 	pinctrl-0 = <&spi3_pins>, <&spi3quad_pins>;
 	status = "okay";
-	spi-nor@0 {
+	flash@0 {
 		compatible = "jedec,spi-nor";
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -324,7 +324,7 @@
 &spi0 {
 	cs-gpios = <&gpio6 11 GPIO_ACTIVE_LOW>;
 	status = "okay";
-	Flash@0 {
+	flash@0 {
 		compatible = "winbond,w25q128",
 		"jedec,spi-nor";
 		reg = <0x0>;
@@ -345,7 +345,7 @@
 &spi1 {
 	cs-gpios = <&gpio0 20 GPIO_ACTIVE_LOW>;
 	status = "okay";
-	Flash@0 {
+	flash@0 {
 		compatible = "winbond,w25q128fw",
 		"jedec,spi-nor";
 		reg = <0x0>;
diff --git a/arch/arm/boot/dts/nuvoton-npcm750-runbmc-olympus.dts b/arch/arm/boot/dts/nuvoton-npcm750-runbmc-olympus.dts
index 767e0ac0df7c..132e702281fc 100644
--- a/arch/arm/boot/dts/nuvoton-npcm750-runbmc-olympus.dts
+++ b/arch/arm/boot/dts/nuvoton-npcm750-runbmc-olympus.dts
@@ -100,7 +100,7 @@
 	pinctrl-0 = <&spi0cs1_pins>;
 	status = "okay";
 
-	spi-nor@0 {
+	flash@0 {
 		compatible = "jedec,spi-nor";
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -139,7 +139,7 @@
 		};
 	};
 
-	spi-nor@1 {
+	flash@1 {
 		compatible = "jedec,spi-nor";
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -166,7 +166,7 @@
 	pinctrl-0 = <&spi3_pins>;
 	status = "okay";
 
-	spi-nor@0 {
+	flash@0 {
 		compatible = "jedec,spi-nor";
 		#address-cells = <1>;
 		#size-cells = <1>;
diff --git a/arch/arm/boot/dts/nuvoton-npcm750.dtsi b/arch/arm/boot/dts/nuvoton-npcm750.dtsi
index 13eee0fe5642..30eed40b89b5 100644
--- a/arch/arm/boot/dts/nuvoton-npcm750.dtsi
+++ b/arch/arm/boot/dts/nuvoton-npcm750.dtsi
@@ -51,7 +51,7 @@
 			interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "macirq";
 			ethernet = <1>;
-			clocks	= <&clk_rg2refck>, <&clk NPCM7XX_CLK_AHB>;
+			clocks = <&clk_rg2refck>, <&clk NPCM7XX_CLK_AHB>;
 			clock-names = "stmmaceth", "clk_gmac";
 			pinctrl-names = "default";
 			pinctrl-0 = <&rg2_pins
diff --git a/arch/arm/boot/dts/nuvoton-wpcm450-supermicro-x9sci-ln4f.dts b/arch/arm/boot/dts/nuvoton-wpcm450-supermicro-x9sci-ln4f.dts
index 83f27fbf4e93..3ee61251a16d 100644
--- a/arch/arm/boot/dts/nuvoton-wpcm450-supermicro-x9sci-ln4f.dts
+++ b/arch/arm/boot/dts/nuvoton-wpcm450-supermicro-x9sci-ln4f.dts
@@ -8,6 +8,9 @@
 
 #include "nuvoton-wpcm450.dtsi"
 
+#include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/gpio/gpio.h>
+
 / {
 	model = "Supermicro X9SCi-LN4F BMC";
 	compatible = "supermicro,x9sci-ln4f-bmc", "nuvoton,wpcm450";
@@ -20,6 +23,46 @@
 		device_type = "memory";
 		reg = <0 0x08000000>; /* 128 MiB */
 	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&key_pins>;
+
+		uid {
+			label = "UID button";
+			linux,code = <KEY_HOME>;
+			gpios = <&gpio0 14 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&led_pins>;
+
+		uid {
+			label = "UID";
+			gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
+		};
+
+		heartbeat {
+			label = "heartbeat";
+			gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&pinctrl {
+	key_pins: mux-keys {
+		groups = "gspi", "sspi";
+		function = "gpio";
+	};
+
+	led_pins: mux-leds {
+		groups = "hg3", "hg0", "pwm4";
+		function = "gpio";
+	};
 };
 
 &serial0 {
diff --git a/arch/arm/boot/dts/nuvoton-wpcm450.dtsi b/arch/arm/boot/dts/nuvoton-wpcm450.dtsi
index d7cbeb187484..93595850a4c3 100644
--- a/arch/arm/boot/dts/nuvoton-wpcm450.dtsi
+++ b/arch/arm/boot/dts/nuvoton-wpcm450.dtsi
@@ -8,6 +8,17 @@
 	#address-cells = <1>;
 	#size-cells = <1>;
 
+	aliases {
+		gpio0 = &gpio0;
+		gpio1 = &gpio1;
+		gpio2 = &gpio2;
+		gpio3 = &gpio3;
+		gpio4 = &gpio4;
+		gpio5 = &gpio5;
+		gpio6 = &gpio6;
+		gpio7 = &gpio7;
+	};
+
 	cpus {
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -33,12 +44,19 @@
 		interrupt-parent = <&aic>;
 		ranges;
 
+		gcr: syscon@b0000000 {
+			compatible = "nuvoton,wpcm450-gcr", "syscon", "simple-mfd";
+			reg = <0xb0000000 0x200>;
+		};
+
 		serial0: serial@b8000000 {
 			compatible = "nuvoton,wpcm450-uart";
 			reg = <0xb8000000 0x20>;
 			reg-shift = <2>;
 			interrupts = <7 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&clk24m>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&bsp_pins>;
 			status = "disabled";
 		};
 
@@ -72,5 +90,371 @@
 			interrupt-controller;
 			#interrupt-cells = <2>;
 		};
+
+		pinctrl: pinctrl@b8003000 {
+			compatible = "nuvoton,wpcm450-pinctrl";
+			reg = <0xb8003000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			gpio0: gpio@0 {
+				reg = <0>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupts = <2 IRQ_TYPE_LEVEL_HIGH>,
+					     <3 IRQ_TYPE_LEVEL_HIGH>,
+					     <4 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-controller;
+			};
+
+			gpio1: gpio@1 {
+				reg = <1>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupts = <5 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-controller;
+			};
+
+			gpio2: gpio@2 {
+				reg = <2>;
+				gpio-controller;
+				#gpio-cells = <2>;
+			};
+
+			gpio3: gpio@3 {
+				reg = <3>;
+				gpio-controller;
+				#gpio-cells = <2>;
+			};
+
+			gpio4: gpio@4 {
+				reg = <4>;
+				gpio-controller;
+				#gpio-cells = <2>;
+			};
+
+			gpio5: gpio@5 {
+				reg = <5>;
+				gpio-controller;
+				#gpio-cells = <2>;
+			};
+
+			gpio6: gpio@6 {
+				reg = <6>;
+				gpio-controller;
+				#gpio-cells = <2>;
+			};
+
+			gpio7: gpio@7 {
+				reg = <7>;
+				gpio-controller;
+				#gpio-cells = <2>;
+			};
+
+			smb3_pins: mux-smb3 {
+				groups = "smb3";
+				function = "smb3";
+			};
+
+			smb4_pins: mux-smb4 {
+				groups = "smb4";
+				function = "smb4";
+			};
+
+			smb5_pins: mux-smb5 {
+				groups = "smb5";
+				function = "smb5";
+			};
+
+			scs1_pins: mux-scs1 {
+				groups = "scs1";
+				function = "scs1";
+			};
+
+			scs2_pins: mux-scs2 {
+				groups = "scs2";
+				function = "scs2";
+			};
+
+			scs3_pins: mux-scs3 {
+				groups = "scs3";
+				function = "scs3";
+			};
+
+			smb0_pins: mux-smb0 {
+				groups = "smb0";
+				function = "smb0";
+			};
+
+			smb1_pins: mux-smb1 {
+				groups = "smb1";
+				function = "smb1";
+			};
+
+			smb2_pins: mux-smb2 {
+				groups = "smb2";
+				function = "smb2";
+			};
+
+			bsp_pins: mux-bsp {
+				groups = "bsp";
+				function = "bsp";
+			};
+
+			hsp1_pins: mux-hsp1 {
+				groups = "hsp1";
+				function = "hsp1";
+			};
+
+			hsp2_pins: mux-hsp2 {
+				groups = "hsp2";
+				function = "hsp2";
+			};
+
+			r1err_pins: mux-r1err {
+				groups = "r1err";
+				function = "r1err";
+			};
+
+			r1md_pins: mux-r1md {
+				groups = "r1md";
+				function = "r1md";
+			};
+
+			rmii2_pins: mux-rmii2 {
+				groups = "rmii2";
+				function = "rmii2";
+			};
+
+			r2err_pins: mux-r2err {
+				groups = "r2err";
+				function = "r2err";
+			};
+
+			r2md_pins: mux-r2md {
+				groups = "r2md";
+				function = "r2md";
+			};
+
+			kbcc_pins: mux-kbcc {
+				groups = "kbcc";
+				function = "kbcc";
+			};
+
+			dvo0_pins: mux-dvo0 {
+				groups = "dvo";
+				function = "dvo0";
+			};
+
+			dvo3_pins: mux-dvo3 {
+				groups = "dvo";
+				function = "dvo3";
+			};
+
+			clko_pins: mux-clko {
+				groups = "clko";
+				function = "clko";
+			};
+
+			smi_pins: mux-smi {
+				groups = "smi";
+				function = "smi";
+			};
+
+			uinc_pins: mux-uinc {
+				groups = "uinc";
+				function = "uinc";
+			};
+
+			gspi_pins: mux-gspi {
+				groups = "gspi";
+				function = "gspi";
+			};
+
+			mben_pins: mux-mben {
+				groups = "mben";
+				function = "mben";
+			};
+
+			xcs2_pins: mux-xcs2 {
+				groups = "xcs2";
+				function = "xcs2";
+			};
+
+			xcs1_pins: mux-xcs1 {
+				groups = "xcs1";
+				function = "xcs1";
+			};
+
+			sdio_pins: mux-sdio {
+				groups = "sdio";
+				function = "sdio";
+			};
+
+			sspi_pins: mux-sspi {
+				groups = "sspi";
+				function = "sspi";
+			};
+
+			fi0_pins: mux-fi0 {
+				groups = "fi0";
+				function = "fi0";
+			};
+
+			fi1_pins: mux-fi1 {
+				groups = "fi1";
+				function = "fi1";
+			};
+
+			fi2_pins: mux-fi2 {
+				groups = "fi2";
+				function = "fi2";
+			};
+
+			fi3_pins: mux-fi3 {
+				groups = "fi3";
+				function = "fi3";
+			};
+
+			fi4_pins: mux-fi4 {
+				groups = "fi4";
+				function = "fi4";
+			};
+
+			fi5_pins: mux-fi5 {
+				groups = "fi5";
+				function = "fi5";
+			};
+
+			fi6_pins: mux-fi6 {
+				groups = "fi6";
+				function = "fi6";
+			};
+
+			fi7_pins: mux-fi7 {
+				groups = "fi7";
+				function = "fi7";
+			};
+
+			fi8_pins: mux-fi8 {
+				groups = "fi8";
+				function = "fi8";
+			};
+
+			fi9_pins: mux-fi9 {
+				groups = "fi9";
+				function = "fi9";
+			};
+
+			fi10_pins: mux-fi10 {
+				groups = "fi10";
+				function = "fi10";
+			};
+
+			fi11_pins: mux-fi11 {
+				groups = "fi11";
+				function = "fi11";
+			};
+
+			fi12_pins: mux-fi12 {
+				groups = "fi12";
+				function = "fi12";
+			};
+
+			fi13_pins: mux-fi13 {
+				groups = "fi13";
+				function = "fi13";
+			};
+
+			fi14_pins: mux-fi14 {
+				groups = "fi14";
+				function = "fi14";
+			};
+
+			fi15_pins: mux-fi15 {
+				groups = "fi15";
+				function = "fi15";
+			};
+
+			pwm0_pins: mux-pwm0 {
+				groups = "pwm0";
+				function = "pwm0";
+			};
+
+			pwm1_pins: mux-pwm1 {
+				groups = "pwm1";
+				function = "pwm1";
+			};
+
+			pwm2_pins: mux-pwm2 {
+				groups = "pwm2";
+				function = "pwm2";
+			};
+
+			pwm3_pins: mux-pwm3 {
+				groups = "pwm3";
+				function = "pwm3";
+			};
+
+			pwm4_pins: mux-pwm4 {
+				groups = "pwm4";
+				function = "pwm4";
+			};
+
+			pwm5_pins: mux-pwm5 {
+				groups = "pwm5";
+				function = "pwm5";
+			};
+
+			pwm6_pins: mux-pwm6 {
+				groups = "pwm6";
+				function = "pwm6";
+			};
+
+			pwm7_pins: mux-pwm7 {
+				groups = "pwm7";
+				function = "pwm7";
+			};
+
+			hg0_pins: mux-hg0 {
+				groups = "hg0";
+				function = "hg0";
+			};
+
+			hg1_pins: mux-hg1 {
+				groups = "hg1";
+				function = "hg1";
+			};
+
+			hg2_pins: mux-hg2 {
+				groups = "hg2";
+				function = "hg2";
+			};
+
+			hg3_pins: mux-hg3 {
+				groups = "hg3";
+				function = "hg3";
+			};
+
+			hg4_pins: mux-hg4 {
+				groups = "hg4";
+				function = "hg4";
+			};
+
+			hg5_pins: mux-hg5 {
+				groups = "hg5";
+				function = "hg5";
+			};
+
+			hg6_pins: mux-hg6 {
+				groups = "hg6";
+				function = "hg6";
+			};
+
+			hg7_pins: mux-hg7 {
+				groups = "hg7";
+				function = "hg7";
+			};
+		};
 	};
 };
diff --git a/arch/arm/boot/dts/omap2.dtsi b/arch/arm/boot/dts/omap2.dtsi
index 5750ca1233cc..afabb36a8ac1 100644
--- a/arch/arm/boot/dts/omap2.dtsi
+++ b/arch/arm/boot/dts/omap2.dtsi
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Device Tree Source for OMAP2 SoC
  *
  * Copyright (C) 2011 Texas Instruments Incorporated - https://www.ti.com/
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2.  This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
  */
 
 #include <dt-bindings/bus/ti-sysc.h>
diff --git a/arch/arm/boot/dts/omap2420-h4.dts b/arch/arm/boot/dts/omap2420-h4.dts
index af964f139abf..5acf5dd87c59 100644
--- a/arch/arm/boot/dts/omap2420-h4.dts
+++ b/arch/arm/boot/dts/omap2420-h4.dts
@@ -21,7 +21,7 @@
 
 	nor@0,0 {
 		compatible = "cfi-flash";
-		linux,mtd-name= "intel,ge28f256l18b85";
+		linux,mtd-name = "intel,ge28f256l18b85";
 		#address-cells = <1>;
 		#size-cells = <1>;
 		reg = <0 0 0x04000000>;
diff --git a/arch/arm/boot/dts/omap2420.dtsi b/arch/arm/boot/dts/omap2420.dtsi
index bb529a2a295d..821da51cb870 100644
--- a/arch/arm/boot/dts/omap2420.dtsi
+++ b/arch/arm/boot/dts/omap2420.dtsi
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Device Tree Source for OMAP2420 SoC
  *
  * Copyright (C) 2012 Texas Instruments Incorporated - https://www.ti.com/
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2.  This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
  */
 
 #include "omap2.dtsi"
diff --git a/arch/arm/boot/dts/omap2430.dtsi b/arch/arm/boot/dts/omap2430.dtsi
index 23115ba61bc0..b9a9e6e45266 100644
--- a/arch/arm/boot/dts/omap2430.dtsi
+++ b/arch/arm/boot/dts/omap2430.dtsi
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Device Tree Source for OMAP243x SoC
  *
  * Copyright (C) 2012 Texas Instruments Incorporated - https://www.ti.com/
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2.  This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
  */
 
 #include "omap2.dtsi"
diff --git a/arch/arm/boot/dts/omap3-beagle-ab4.dts b/arch/arm/boot/dts/omap3-beagle-ab4.dts
new file mode 100644
index 000000000000..990ff2d84686
--- /dev/null
+++ b/arch/arm/boot/dts/omap3-beagle-ab4.dts
@@ -0,0 +1,47 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/dts-v1/;
+
+#include "omap3-beagle.dts"
+
+/ {
+	model = "TI OMAP3 BeagleBoard A to B4";
+	compatible = "ti,omap3-beagle-ab4", "ti,omap3-beagle", "ti,omap3430", "ti,omap3";
+};
+
+/*
+ * Workaround for capacitor C70 issue, see "Boards revision A and < B5"
+ * section at https://elinux.org/BeagleBoard_Community
+ */
+
+/* Unusable as clocksource because of unreliable oscillator */
+&counter32k {
+	status = "disabled";
+};
+
+/* Unusable as clockevent because of unreliable oscillator, allow to idle */
+&timer1_target {
+	/delete-property/ti,no-reset-on-init;
+	/delete-property/ti,no-idle;
+	timer@0 {
+		/delete-property/ti,timer-alwon;
+	};
+};
+
+/* Preferred always-on timer for clocksource */
+&timer12_target {
+	ti,no-reset-on-init;
+	ti,no-idle;
+	timer@0 {
+		/* Always clocked by secure_32k_fck */
+	};
+};
+
+/* Preferred timer for clockevent */
+&timer2_target {
+	ti,no-reset-on-init;
+	ti,no-idle;
+	timer@0 {
+		assigned-clocks = <&gpt2_fck>;
+		assigned-clock-parents = <&sys_ck>;
+	};
+};
diff --git a/arch/arm/boot/dts/omap3-beagle-xm.dts b/arch/arm/boot/dts/omap3-beagle-xm.dts
index a858ebfa1500..35eced6521ef 100644
--- a/arch/arm/boot/dts/omap3-beagle-xm.dts
+++ b/arch/arm/boot/dts/omap3-beagle-xm.dts
@@ -370,7 +370,7 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		ethernet: usbether@1 {
+		ethernet: ethernet@1 {
 			compatible = "usb424,ec00";
 			reg = <1>;
 		};
diff --git a/arch/arm/boot/dts/omap3-beagle.dts b/arch/arm/boot/dts/omap3-beagle.dts
index f9f34b8458e9..0548b391334f 100644
--- a/arch/arm/boot/dts/omap3-beagle.dts
+++ b/arch/arm/boot/dts/omap3-beagle.dts
@@ -304,39 +304,6 @@
 	phys = <0 &hsusb2_phy>;
 };
 
-/* Unusable as clocksource because of unreliable oscillator */
-&counter32k {
-	status = "disabled";
-};
-
-/* Unusable as clockevent because if unreliable oscillator, allow to idle */
-&timer1_target {
-	/delete-property/ti,no-reset-on-init;
-	/delete-property/ti,no-idle;
-	timer@0 {
-		/delete-property/ti,timer-alwon;
-	};
-};
-
-/* Preferred always-on timer for clocksource */
-&timer12_target {
-	ti,no-reset-on-init;
-	ti,no-idle;
-	timer@0 {
-		/* Always clocked by secure_32k_fck */
-	};
-};
-
-/* Preferred timer for clockevent */
-&timer2_target {
-	ti,no-reset-on-init;
-	ti,no-idle;
-	timer@0 {
-		assigned-clocks = <&gpt2_fck>;
-		assigned-clock-parents = <&sys_ck>;
-	};
-};
-
 &twl_gpio {
 	ti,use-leds;
 	/* pullups: BIT(1) */
diff --git a/arch/arm/boot/dts/omap3-cpu-thermal.dtsi b/arch/arm/boot/dts/omap3-cpu-thermal.dtsi
index a9069cca5888..0da759f8e2c2 100644
--- a/arch/arm/boot/dts/omap3-cpu-thermal.dtsi
+++ b/arch/arm/boot/dts/omap3-cpu-thermal.dtsi
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Device Tree Source for OMAP3 SoC CPU thermal
  *
  * Copyright (C) 2017 Texas Instruments Incorporated - https://www.ti.com/
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2.  This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
  */
 
 #include <dt-bindings/thermal/thermal.h>
diff --git a/arch/arm/boot/dts/omap3-devkit8000-common.dtsi b/arch/arm/boot/dts/omap3-devkit8000-common.dtsi
index 5e55198e4576..54cd37336be7 100644
--- a/arch/arm/boot/dts/omap3-devkit8000-common.dtsi
+++ b/arch/arm/boot/dts/omap3-devkit8000-common.dtsi
@@ -158,6 +158,24 @@
 	status = "disabled";
 };
 
+/* Unusable as clockevent because if unreliable oscillator, allow to idle */
+&timer1_target {
+	/delete-property/ti,no-reset-on-init;
+	/delete-property/ti,no-idle;
+	timer@0 {
+		/delete-property/ti,timer-alwon;
+	};
+};
+
+/* Preferred timer for clockevent */
+&timer12_target {
+	ti,no-reset-on-init;
+	ti,no-idle;
+	timer@0 {
+		/* Always clocked by secure_32k_fck */
+	};
+};
+
 &twl_gpio {
 	ti,use-leds;
 	/*
diff --git a/arch/arm/boot/dts/omap3-devkit8000.dts b/arch/arm/boot/dts/omap3-devkit8000.dts
index c2995a280729..162d0726b008 100644
--- a/arch/arm/boot/dts/omap3-devkit8000.dts
+++ b/arch/arm/boot/dts/omap3-devkit8000.dts
@@ -14,36 +14,3 @@
 		display2 = &tv0;
 	};
 };
-
-/* Unusable as clocksource because of unreliable oscillator */
-&counter32k {
-	status = "disabled";
-};
-
-/* Unusable as clockevent because if unreliable oscillator, allow to idle */
-&timer1_target {
-	/delete-property/ti,no-reset-on-init;
-	/delete-property/ti,no-idle;
-	timer@0 {
-		/delete-property/ti,timer-alwon;
-	};
-};
-
-/* Preferred always-on timer for clocksource */
-&timer12_target {
-	ti,no-reset-on-init;
-	ti,no-idle;
-	timer@0 {
-		/* Always clocked by secure_32k_fck */
-	};
-};
-
-/* Preferred timer for clockevent */
-&timer2_target {
-	ti,no-reset-on-init;
-	ti,no-idle;
-	timer@0 {
-		assigned-clocks = <&gpt2_fck>;
-		assigned-clock-parents = <&sys_ck>;
-	};
-};
diff --git a/arch/arm/boot/dts/omap3-evm-37xx.dts b/arch/arm/boot/dts/omap3-evm-37xx.dts
index c9332195d096..abd403c228c7 100644
--- a/arch/arm/boot/dts/omap3-evm-37xx.dts
+++ b/arch/arm/boot/dts/omap3-evm-37xx.dts
@@ -60,7 +60,7 @@
 		interrupt-parent = <&gpmc>;
 		interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
 			     <1 IRQ_TYPE_NONE>;	/* termcount */
-		linux,mtd-name= "hynix,h8kds0un0mer-4em";
+		linux,mtd-name = "hynix,h8kds0un0mer-4em";
 		nand-bus-width = <16>;
 		gpmc,device-width = <2>;
 		ti,nand-ecc-opt = "bch8";
diff --git a/arch/arm/boot/dts/omap3-evm.dts b/arch/arm/boot/dts/omap3-evm.dts
index 5cc0cf7cd16c..f95eea63b355 100644
--- a/arch/arm/boot/dts/omap3-evm.dts
+++ b/arch/arm/boot/dts/omap3-evm.dts
@@ -60,7 +60,7 @@
 		interrupt-parent = <&gpmc>;
 		interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
 			     <1 IRQ_TYPE_NONE>;	/* termcount */
-		linux,mtd-name= "micron,mt29f2g16abdhc";
+		linux,mtd-name = "micron,mt29f2g16abdhc";
 		nand-bus-width = <16>;
 		gpmc,device-width = <2>;
 		ti,nand-ecc-opt = "bch8";
diff --git a/arch/arm/boot/dts/omap3-gta04.dtsi b/arch/arm/boot/dts/omap3-gta04.dtsi
index 7e3d8147e2c1..28a6a9345be5 100644
--- a/arch/arm/boot/dts/omap3-gta04.dtsi
+++ b/arch/arm/boot/dts/omap3-gta04.dtsi
@@ -31,6 +31,8 @@
 	aliases {
 		display0 = &lcd;
 		display1 = &tv0;
+		/delete-property/ mmc2;
+		/delete-property/ mmc3;
 	};
 
 	ldo_3v3: fixedregulator {
@@ -125,7 +127,7 @@
 			spi-cpol;
 			spi-cpha;
 
-			backlight= <&backlight>;
+			backlight = <&backlight>;
 			label = "lcd";
 			port {
 				lcd_in: endpoint {
diff --git a/arch/arm/boot/dts/omap3-igep.dtsi b/arch/arm/boot/dts/omap3-igep.dtsi
index 99f5585097a1..219202610463 100644
--- a/arch/arm/boot/dts/omap3-igep.dtsi
+++ b/arch/arm/boot/dts/omap3-igep.dtsi
@@ -111,7 +111,7 @@
 		interrupt-parent = <&gpmc>;
 		interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
 			     <1 IRQ_TYPE_NONE>;	/* termcount */
-		linux,mtd-name= "micron,mt29c4g96maz";
+		linux,mtd-name = "micron,mt29c4g96maz";
 		nand-bus-width = <16>;
 		gpmc,device-width = <2>;
 		ti,nand-ecc-opt = "bch8";
diff --git a/arch/arm/boot/dts/omap3-ldp.dts b/arch/arm/boot/dts/omap3-ldp.dts
index 9c6a92724590..36fc8805e0c1 100644
--- a/arch/arm/boot/dts/omap3-ldp.dts
+++ b/arch/arm/boot/dts/omap3-ldp.dts
@@ -103,7 +103,7 @@
 		interrupt-parent = <&gpmc>;
 		interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
 			     <1 IRQ_TYPE_NONE>;	/* termcount */
-		linux,mtd-name= "micron,nand";
+		linux,mtd-name = "micron,nand";
 		nand-bus-width = <16>;
 		gpmc,device-width = <2>;
 		ti,nand-ecc-opt = "bch8";
@@ -215,11 +215,11 @@
 };
 
 &mmc2 {
-	status="disabled";
+	status = "disabled";
 };
 
 &mmc3 {
-	status="disabled";
+	status = "disabled";
 };
 
 &omap3_pmx_core {
diff --git a/arch/arm/boot/dts/omap3-lilly-a83x.dtsi b/arch/arm/boot/dts/omap3-lilly-a83x.dtsi
index 73d477898ec2..c595afe4181d 100644
--- a/arch/arm/boot/dts/omap3-lilly-a83x.dtsi
+++ b/arch/arm/boot/dts/omap3-lilly-a83x.dtsi
@@ -372,7 +372,7 @@
 		gpmc,device-width = <2>;
 		gpmc,wait-pin = <0>;
 		gpmc,wait-monitoring-ns = <0>;
-		gpmc,burst-length= <4>;
+		gpmc,burst-length = <4>;
 		gpmc,cs-on-ns = <0>;
 		gpmc,cs-rd-off-ns = <100>;
 		gpmc,cs-wr-off-ns = <100>;
diff --git a/arch/arm/boot/dts/omap3-n900.dts b/arch/arm/boot/dts/omap3-n900.dts
index 32335d4ce478..dd7971556449 100644
--- a/arch/arm/boot/dts/omap3-n900.dts
+++ b/arch/arm/boot/dts/omap3-n900.dts
@@ -8,6 +8,7 @@
 
 #include "omap34xx.dtsi"
 #include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
 
 /*
  * Default secure signed bootloader (Nokia X-Loader) does not enable L3 firewall
@@ -567,8 +568,8 @@
 };
 
 &twl_gpio {
-	ti,pullups	= <0x0>;
-	ti,pulldowns	= <0x03ff3f>; /* BIT(0..5) | BIT(8..17) */
+	ti,pullups = <0x0>;
+	ti,pulldowns = <0x03ff3f>; /* BIT(0..5) | BIT(8..17) */
 };
 
 &i2c2 {
@@ -630,63 +631,92 @@
 	};
 
 	lp5523: lp5523@32 {
+		#address-cells = <1>;
+		#size-cells = <0>;
 		compatible = "national,lp5523";
 		reg = <0x32>;
 		clock-mode = /bits/ 8 <0>; /* LP55XX_CLOCK_AUTO */
-		enable-gpio = <&gpio2 9 GPIO_ACTIVE_HIGH>; /* 41 */
+		enable-gpios = <&gpio2 9 GPIO_ACTIVE_HIGH>; /* 41 */
 
-		chan0 {
+		led@0 {
+			reg = <0>;
 			chan-name = "lp5523:kb1";
 			led-cur = /bits/ 8 <50>;
 			max-cur = /bits/ 8 <100>;
+			color = <LED_COLOR_ID_WHITE>;
+			function = LED_FUNCTION_KBD_BACKLIGHT;
 		};
 
-		chan1 {
+		led@1 {
+			reg = <1>;
 			chan-name = "lp5523:kb2";
 			led-cur = /bits/ 8 <50>;
 			max-cur = /bits/ 8 <100>;
+			color = <LED_COLOR_ID_WHITE>;
+			function = LED_FUNCTION_KBD_BACKLIGHT;
 		};
 
-		chan2 {
+		led@2 {
+			reg = <2>;
 			chan-name = "lp5523:kb3";
 			led-cur = /bits/ 8 <50>;
 			max-cur = /bits/ 8 <100>;
+			color = <LED_COLOR_ID_WHITE>;
+			function = LED_FUNCTION_KBD_BACKLIGHT;
 		};
 
-		chan3 {
+		led@3 {
+			reg = <3>;
 			chan-name = "lp5523:kb4";
 			led-cur = /bits/ 8 <50>;
 			max-cur = /bits/ 8 <100>;
+			color = <LED_COLOR_ID_WHITE>;
+			function = LED_FUNCTION_KBD_BACKLIGHT;
 		};
 
-		chan4 {
+		led@4 {
+			reg = <4>;
 			chan-name = "lp5523:b";
 			led-cur = /bits/ 8 <50>;
 			max-cur = /bits/ 8 <100>;
+			color = <LED_COLOR_ID_BLUE>;
+			function = LED_FUNCTION_STATUS;
 		};
 
-		chan5 {
+		led@5 {
+			reg = <5>;
 			chan-name = "lp5523:g";
 			led-cur = /bits/ 8 <50>;
 			max-cur = /bits/ 8 <100>;
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_STATUS;
 		};
 
-		chan6 {
+		led@6 {
+			reg = <6>;
 			chan-name = "lp5523:r";
 			led-cur = /bits/ 8 <50>;
 			max-cur = /bits/ 8 <100>;
+			color = <LED_COLOR_ID_RED>;
+			function = LED_FUNCTION_STATUS;
 		};
 
-		chan7 {
+		led@7 {
+			reg = <7>;
 			chan-name = "lp5523:kb5";
 			led-cur = /bits/ 8 <50>;
 			max-cur = /bits/ 8 <100>;
+			color = <LED_COLOR_ID_WHITE>;
+			function = LED_FUNCTION_KBD_BACKLIGHT;
 		};
 
-		chan8 {
+		led@8 {
+			reg = <8>;
 			chan-name = "lp5523:kb6";
 			led-cur = /bits/ 8 <50>;
 			max-cur = /bits/ 8 <100>;
+			color = <LED_COLOR_ID_WHITE>;
+			function = LED_FUNCTION_KBD_BACKLIGHT;
 		};
 	};
 
diff --git a/arch/arm/boot/dts/omap3-n950-n9.dtsi b/arch/arm/boot/dts/omap3-n950-n9.dtsi
index 7dde9fbb06d3..f68da828b050 100644
--- a/arch/arm/boot/dts/omap3-n950-n9.dtsi
+++ b/arch/arm/boot/dts/omap3-n950-n9.dtsi
@@ -162,8 +162,8 @@
 };
 
 &twl_gpio {
-	ti,pullups	= <0x000001>; /* BIT(0) */
-	ti,pulldowns	= <0x008106>; /* BIT(1) | BIT(2) | BIT(8) | BIT(15) */
+	ti,pullups = <0x000001>; /* BIT(0) */
+	ti,pulldowns = <0x008106>; /* BIT(1) | BIT(2) | BIT(8) | BIT(15) */
 };
 
 &vdac {
diff --git a/arch/arm/boot/dts/omap3-overo-base.dtsi b/arch/arm/boot/dts/omap3-overo-base.dtsi
index 006a6d97231c..adc714c39825 100644
--- a/arch/arm/boot/dts/omap3-overo-base.dtsi
+++ b/arch/arm/boot/dts/omap3-overo-base.dtsi
@@ -222,7 +222,7 @@
 
 	nand@0,0 {
 		compatible = "ti,omap2-nand";
-		linux,mtd-name= "micron,mt29c4g96maz";
+		linux,mtd-name = "micron,mt29c4g96maz";
 		reg = <0 0 4>;	/* CS0, offset 0, IO size 4 */
 		interrupt-parent = <&gpmc>;
 		interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
diff --git a/arch/arm/boot/dts/omap3-pandora-common.dtsi b/arch/arm/boot/dts/omap3-pandora-common.dtsi
index 37608af6c07f..559853764487 100644
--- a/arch/arm/boot/dts/omap3-pandora-common.dtsi
+++ b/arch/arm/boot/dts/omap3-pandora-common.dtsi
@@ -666,7 +666,7 @@
 
 	lcd: lcd@1 {
 		reg = <1>;	/* CS1 */
-		compatible =	"tpo,td043mtea1";
+		compatible = "tpo,td043mtea1";
 		spi-max-frequency = <100000>;
 		spi-cpol;
 		spi-cpha;
diff --git a/arch/arm/boot/dts/omap3-tao3530.dtsi b/arch/arm/boot/dts/omap3-tao3530.dtsi
index 580bfa1931c8..7f440d11f7e7 100644
--- a/arch/arm/boot/dts/omap3-tao3530.dtsi
+++ b/arch/arm/boot/dts/omap3-tao3530.dtsi
@@ -197,25 +197,11 @@
 &mcspi1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mcspi1_pins>;
-
-	spidev@0 {
-		compatible = "spidev";
-		spi-max-frequency = <48000000>;
-		reg = <0>;
-		spi-cpha;
-	};
 };
 
 &mcspi3 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&mcspi3_pins>;
-
-	spidev@0 {
-		compatible = "spidev";
-		spi-max-frequency = <48000000>;
-		reg = <0>;
-		spi-cpha;
-	};
 };
 
 #include "twl4030.dtsi"
diff --git a/arch/arm/boot/dts/omap3.dtsi b/arch/arm/boot/dts/omap3.dtsi
index 64b7e6fddd1b..825075ff0e34 100644
--- a/arch/arm/boot/dts/omap3.dtsi
+++ b/arch/arm/boot/dts/omap3.dtsi
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Device Tree Source for OMAP3 SoC
  *
  * Copyright (C) 2011 Texas Instruments Incorporated - https://www.ti.com/
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2.  This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
  */
 
 #include <dt-bindings/bus/ti-sysc.h>
diff --git a/arch/arm/boot/dts/omap3430-sdp.dts b/arch/arm/boot/dts/omap3430-sdp.dts
index 7d530ae3483b..258ecd9e4519 100644
--- a/arch/arm/boot/dts/omap3430-sdp.dts
+++ b/arch/arm/boot/dts/omap3430-sdp.dts
@@ -53,7 +53,7 @@
 
 	nor@0,0 {
 		compatible = "cfi-flash";
-		linux,mtd-name= "intel,pf48f6000m0y1be";
+		linux,mtd-name = "intel,pf48f6000m0y1be";
 		#address-cells = <1>;
 		#size-cells = <1>;
 		reg = <0 0 0x08000000>;
@@ -105,7 +105,7 @@
 		interrupt-parent = <&gpmc>;
 		interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
 			     <1 IRQ_TYPE_NONE>;	/* termcount */
-		linux,mtd-name= "micron,mt29f1g08abb";
+		linux,mtd-name = "micron,mt29f1g08abb";
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ti,nand-ecc-opt = "sw";
@@ -148,7 +148,7 @@
 	};
 
 	onenand@2,0 {
-		linux,mtd-name= "samsung,kfm2g16q2m-deb8";
+		linux,mtd-name = "samsung,kfm2g16q2m-deb8";
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "ti,omap2-onenand";
diff --git a/arch/arm/boot/dts/omap3430es1-clocks.dtsi b/arch/arm/boot/dts/omap3430es1-clocks.dtsi
index 2ec3628d3315..24adfac26be0 100644
--- a/arch/arm/boot/dts/omap3430es1-clocks.dtsi
+++ b/arch/arm/boot/dts/omap3430es1-clocks.dtsi
@@ -46,37 +46,61 @@
 		ti,bit-shift = <2>;
 	};
 
-	d2d_26m_fck: d2d_26m_fck@a00 {
-		#clock-cells = <0>;
-		compatible = "ti,wait-gate-clock";
-		clocks = <&sys_ck>;
-		reg = <0x0a00>;
-		ti,bit-shift = <3>;
-	};
-
-	fshostusb_fck: fshostusb_fck@a00 {
-		#clock-cells = <0>;
-		compatible = "ti,wait-gate-clock";
-		clocks = <&core_48m_fck>;
-		reg = <0x0a00>;
-		ti,bit-shift = <5>;
-	};
-
-	ssi_ssr_gate_fck_3430es1: ssi_ssr_gate_fck_3430es1@a00 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-no-wait-gate-clock";
-		clocks = <&corex2_fck>;
-		ti,bit-shift = <0>;
-		reg = <0x0a00>;
-	};
-
-	ssi_ssr_div_fck_3430es1: ssi_ssr_div_fck_3430es1@a40 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-divider-clock";
-		clocks = <&corex2_fck>;
-		ti,bit-shift = <8>;
-		reg = <0x0a40>;
-		ti,dividers = <0>, <1>, <2>, <3>, <4>, <0>, <6>, <0>, <8>;
+	clock@a00 {
+		compatible = "ti,clksel";
+		reg = <0xa00>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
+
+		d2d_26m_fck: clock-d2d-26m-fck {
+			#clock-cells = <0>;
+			compatible = "ti,wait-gate-clock";
+			clock-output-names = "d2d_26m_fck";
+			clocks = <&sys_ck>;
+			ti,bit-shift = <3>;
+		};
+
+		fshostusb_fck: clock-fshostusb-fck {
+			#clock-cells = <0>;
+			compatible = "ti,wait-gate-clock";
+			clock-output-names = "fshostusb_fck";
+			clocks = <&core_48m_fck>;
+			ti,bit-shift = <5>;
+		};
+
+		ssi_ssr_gate_fck_3430es1: clock-ssi-ssr-gate-fck-3430es1 {
+			#clock-cells = <0>;
+			compatible = "ti,composite-no-wait-gate-clock";
+			clock-output-names = "ssi_ssr_gate_fck_3430es1";
+			clocks = <&corex2_fck>;
+			ti,bit-shift = <0>;
+		};
+	};
+
+	clock@a40 {
+		compatible = "ti,clksel";
+		reg = <0xa40>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
+
+		ssi_ssr_div_fck_3430es1: clock-ssi-ssr-div-fck-3430es1 {
+			#clock-cells = <0>;
+			compatible = "ti,composite-divider-clock";
+			clock-output-names = "ssi_ssr_div_fck_3430es1";
+			clocks = <&corex2_fck>;
+			ti,bit-shift = <8>;
+			ti,dividers = <0>, <1>, <2>, <3>, <4>, <0>, <6>, <0>, <8>;
+		};
+
+		usb_l4_div_ick: clock-usb-l4-div-ick {
+			#clock-cells = <0>;
+			compatible = "ti,composite-divider-clock";
+			clock-output-names = "usb_l4_div_ick";
+			clocks = <&l4_ick>;
+			ti,bit-shift = <4>;
+			ti,max-div = <1>;
+			ti,index-starts-at-one;
+		};
 	};
 
 	ssi_ssr_fck: ssi_ssr_fck_3430es1 {
@@ -93,20 +117,43 @@
 		clock-div = <2>;
 	};
 
-	hsotgusb_ick_3430es1: hsotgusb_ick_3430es1@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-no-wait-interface-clock";
-		clocks = <&core_l3_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <4>;
-	};
-
-	fac_ick: fac_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&core_l4_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <8>;
+	clock@a10 {
+		compatible = "ti,clksel";
+		reg = <0xa10>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
+
+		hsotgusb_ick_3430es1: clock-hsotgusb-ick-3430es1 {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-no-wait-interface-clock";
+			clock-output-names = "hsotgusb_ick_3430es1";
+			clocks = <&core_l3_ick>;
+			ti,bit-shift = <4>;
+		};
+
+		fac_ick: clock-fac-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "fac_ick";
+			clocks = <&core_l4_ick>;
+			ti,bit-shift = <8>;
+		};
+
+		ssi_ick: clock-ssi-ick-3430es1 {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-no-wait-interface-clock";
+			clock-output-names = "ssi_ick_3430es1";
+			clocks = <&ssi_l4_ick>;
+			ti,bit-shift = <0>;
+		};
+
+		usb_l4_gate_ick: clock-usb-l4-gate-ick {
+			#clock-cells = <0>;
+			compatible = "ti,composite-interface-clock";
+			clock-output-names = "usb_l4_gate_ick";
+			clocks = <&l4_ick>;
+			ti,bit-shift = <5>;
+		};
 	};
 
 	ssi_l4_ick: ssi_l4_ick {
@@ -117,45 +164,26 @@
 		clock-div = <1>;
 	};
 
-	ssi_ick: ssi_ick_3430es1@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-no-wait-interface-clock";
-		clocks = <&ssi_l4_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <0>;
-	};
-
-	usb_l4_gate_ick: usb_l4_gate_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-interface-clock";
-		clocks = <&l4_ick>;
-		ti,bit-shift = <5>;
-		reg = <0x0a10>;
-	};
-
-	usb_l4_div_ick: usb_l4_div_ick@a40 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-divider-clock";
-		clocks = <&l4_ick>;
-		ti,bit-shift = <4>;
-		ti,max-div = <1>;
-		reg = <0x0a40>;
-		ti,index-starts-at-one;
-	};
-
 	usb_l4_ick: usb_l4_ick {
 		#clock-cells = <0>;
 		compatible = "ti,composite-clock";
 		clocks = <&usb_l4_gate_ick>, <&usb_l4_div_ick>;
 	};
 
-	dss1_alwon_fck: dss1_alwon_fck_3430es1@e00 {
-		#clock-cells = <0>;
-		compatible = "ti,gate-clock";
-		clocks = <&dpll4_m4x2_ck>;
-		ti,bit-shift = <0>;
-		reg = <0x0e00>;
-		ti,set-rate-parent;
+	clock@e00 {
+		compatible = "ti,clksel";
+		reg = <0xe00>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
+
+		dss1_alwon_fck: clock-dss1-alwon-fck-3430es1 {
+			#clock-cells = <0>;
+			compatible = "ti,gate-clock";
+			clock-output-names = "dss1_alwon_fck_3430es1";
+			clocks = <&dpll4_m4x2_ck>;
+			ti,bit-shift = <0>;
+			ti,set-rate-parent;
+		};
 	};
 
 	dss_ick: dss_ick_3430es1@e10 {
diff --git a/arch/arm/boot/dts/omap34xx-omap36xx-clocks.dtsi b/arch/arm/boot/dts/omap34xx-omap36xx-clocks.dtsi
index 21079cdf2663..8374532f20e2 100644
--- a/arch/arm/boot/dts/omap34xx-omap36xx-clocks.dtsi
+++ b/arch/arm/boot/dts/omap34xx-omap36xx-clocks.dtsi
@@ -13,45 +13,76 @@
 		clock-div = <1>;
 	};
 
-	aes1_ick: aes1_ick@a14 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&security_l4_ick2>;
-		ti,bit-shift = <3>;
-		reg = <0x0a14>;
-	};
+	clock@a14 {
+		compatible = "ti,clksel";
+		reg = <0xa14>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
 
-	rng_ick: rng_ick@a14 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&security_l4_ick2>;
-		reg = <0x0a14>;
-		ti,bit-shift = <2>;
-	};
+		aes1_ick: clock-aes1-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "aes1_ick";
+			clocks = <&security_l4_ick2>;
+			ti,bit-shift = <3>;
+		};
 
-	sha11_ick: sha11_ick@a14 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&security_l4_ick2>;
-		reg = <0x0a14>;
-		ti,bit-shift = <1>;
-	};
+		rng_ick: clock-rng-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "rng_ick";
+			clocks = <&security_l4_ick2>;
+			ti,bit-shift = <2>;
+		};
 
-	des1_ick: des1_ick@a14 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&security_l4_ick2>;
-		reg = <0x0a14>;
-		ti,bit-shift = <0>;
+		sha11_ick: clock-sha11-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "sha11_ick";
+			clocks = <&security_l4_ick2>;
+			ti,bit-shift = <1>;
+		};
+
+		des1_ick: clock-des1-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "des1_ick";
+			clocks = <&security_l4_ick2>;
+			ti,bit-shift = <0>;
+		};
+
+		pka_ick: clock-pka-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "pka_ick";
+			clocks = <&security_l3_ick>;
+			ti,bit-shift = <4>;
+		};
 	};
 
-	cam_mclk: cam_mclk@f00 {
-		#clock-cells = <0>;
-		compatible = "ti,gate-clock";
-		clocks = <&dpll4_m5x2_ck>;
-		ti,bit-shift = <0>;
-		reg = <0x0f00>;
-		ti,set-rate-parent;
+	/* CM_FCLKEN_CAM */
+	clock@f00 {
+		compatible = "ti,clksel";
+		reg = <0xf00>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
+
+		cam_mclk: clock-cam-mclk {
+			#clock-cells = <0>;
+			compatible = "ti,gate-clock";
+			clock-output-names = "cam_mclk";
+			clocks = <&dpll4_m5x2_ck>;
+			ti,bit-shift = <0>;
+			ti,set-rate-parent;
+		};
+
+		csi2_96m_fck: clock-csi2-96m-fck {
+			#clock-cells = <0>;
+			compatible = "ti,gate-clock";
+			clock-output-names = "csi2_96m_fck";
+			clocks = <&core_96m_fck>;
+			ti,bit-shift = <1>;
+		};
 	};
 
 	cam_ick: cam_ick@f10 {
@@ -62,14 +93,6 @@
 		ti,bit-shift = <0>;
 	};
 
-	csi2_96m_fck: csi2_96m_fck@f00 {
-		#clock-cells = <0>;
-		compatible = "ti,gate-clock";
-		clocks = <&core_96m_fck>;
-		reg = <0x0f00>;
-		ti,bit-shift = <1>;
-	};
-
 	security_l3_ick: security_l3_ick {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
@@ -78,44 +101,51 @@
 		clock-div = <1>;
 	};
 
-	pka_ick: pka_ick@a14 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&security_l3_ick>;
-		reg = <0x0a14>;
-		ti,bit-shift = <4>;
-	};
+	clock@a10 {
+		compatible = "ti,clksel";
+		reg = <0xa10>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
 
-	icr_ick: icr_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&core_l4_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <29>;
-	};
+		icr_ick: clock-icr-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "icr_ick";
+			clocks = <&core_l4_ick>;
+			ti,bit-shift = <29>;
+		};
 
-	des2_ick: des2_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&core_l4_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <26>;
-	};
+		des2_ick: clock-des2-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "des2_ick";
+			clocks = <&core_l4_ick>;
+			ti,bit-shift = <26>;
+		};
 
-	mspro_ick: mspro_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&core_l4_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <23>;
-	};
+		mspro_ick: clock-mspro-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "mspro_ick";
+			clocks = <&core_l4_ick>;
+			ti,bit-shift = <23>;
+		};
 
-	mailboxes_ick: mailboxes_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&core_l4_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <7>;
+		mailboxes_ick: clock-mailboxes-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "mailboxes_ick";
+			clocks = <&core_l4_ick>;
+			ti,bit-shift = <7>;
+		};
+
+		sad2d_ick: clock-sad2d-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "sad2d_ick";
+			clocks = <&l3_ick>;
+			ti,bit-shift = <3>;
+		};
 	};
 
 	ssi_l4_ick: ssi_l4_ick {
@@ -126,20 +156,27 @@
 		clock-div = <1>;
 	};
 
-	sr1_fck: sr1_fck@c00 {
-		#clock-cells = <0>;
-		compatible = "ti,wait-gate-clock";
-		clocks = <&sys_ck>;
-		reg = <0x0c00>;
-		ti,bit-shift = <6>;
-	};
+	clock@c00 {
+		compatible = "ti,clksel";
+		reg = <0xc00>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
 
-	sr2_fck: sr2_fck@c00 {
-		#clock-cells = <0>;
-		compatible = "ti,wait-gate-clock";
-		clocks = <&sys_ck>;
-		reg = <0x0c00>;
-		ti,bit-shift = <7>;
+		sr1_fck: clock-sr1-fck {
+			#clock-cells = <0>;
+			compatible = "ti,wait-gate-clock";
+			clock-output-names = "sr1_fck";
+			clocks = <&sys_ck>;
+			ti,bit-shift = <6>;
+		};
+
+		sr2_fck: clock-sr2-fck {
+			#clock-cells = <0>;
+			compatible = "ti,wait-gate-clock";
+			clock-output-names = "sr2_fck";
+			clocks = <&sys_ck>;
+			ti,bit-shift = <7>;
+		};
 	};
 
 	sr_l4_ick: sr_l4_ick {
@@ -187,37 +224,45 @@
 		ti,bit-shift = <0>;
 	};
 
-	modem_fck: modem_fck@a00 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&sys_ck>;
-		reg = <0x0a00>;
-		ti,bit-shift = <31>;
-	};
+	clock@a00 {
+		compatible = "ti,clksel";
+		reg = <0xa00>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
 
-	sad2d_ick: sad2d_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&l3_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <3>;
-	};
+		modem_fck: clock-modem-fck {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "modem_fck";
+			clocks = <&sys_ck>;
+			ti,bit-shift = <31>;
+		};
 
-	mad2d_ick: mad2d_ick@a18 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&l3_ick>;
-		reg = <0x0a18>;
-		ti,bit-shift = <3>;
+		mspro_fck: clock-mspro-fck {
+			#clock-cells = <0>;
+			compatible = "ti,wait-gate-clock";
+			clock-output-names = "mspro_fck";
+			clocks = <&core_96m_fck>;
+			ti,bit-shift = <23>;
+		};
 	};
 
-	mspro_fck: mspro_fck@a00 {
-		#clock-cells = <0>;
-		compatible = "ti,wait-gate-clock";
-		clocks = <&core_96m_fck>;
-		reg = <0x0a00>;
-		ti,bit-shift = <23>;
+	/* CM_ICLKEN3_CORE */
+	clock@a18 {
+		compatible = "ti,clksel";
+		reg = <0xa18>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
+
+		mad2d_ick: clock-mad2d-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "mad2d_ick";
+			clocks = <&l3_ick>;
+			ti,bit-shift = <3>;
+		};
 	};
+
 };
 
 &cm_clockdomains {
diff --git a/arch/arm/boot/dts/omap34xx.dtsi b/arch/arm/boot/dts/omap34xx.dtsi
index 8b8451399784..2eb73ae7ef3e 100644
--- a/arch/arm/boot/dts/omap34xx.dtsi
+++ b/arch/arm/boot/dts/omap34xx.dtsi
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Device Tree Source for OMAP34xx/OMAP35xx SoC
  *
  * Copyright (C) 2013 Texas Instruments Incorporated - https://www.ti.com/
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2.  This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
  */
 
 #include <dt-bindings/bus/ti-sysc.h>
diff --git a/arch/arm/boot/dts/omap36xx-am35xx-omap3430es2plus-clocks.dtsi b/arch/arm/boot/dts/omap36xx-am35xx-omap3430es2plus-clocks.dtsi
index 9974d5226971..dcc5cfcd1fe6 100644
--- a/arch/arm/boot/dts/omap36xx-am35xx-omap3430es2plus-clocks.dtsi
+++ b/arch/arm/boot/dts/omap36xx-am35xx-omap3430es2plus-clocks.dtsi
@@ -133,37 +133,66 @@
 		ti,bit-shift = <2>;
 	};
 
-	usbtll_ick: usbtll_ick@a18 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&core_l4_ick>;
-		reg = <0x0a18>;
-		ti,bit-shift = <2>;
+	/* CM_ICLKEN3_CORE */
+	clock@a18 {
+		compatible = "ti,clksel";
+		reg = <0xa18>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
+
+		usbtll_ick: clock-usbtll-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "usbtll_ick";
+			clocks = <&core_l4_ick>;
+			ti,bit-shift = <2>;
+		};
 	};
 
-	mmchs3_ick: mmchs3_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&core_l4_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <30>;
+	clock@a10 {
+		compatible = "ti,clksel";
+		reg = <0xa10>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
+
+		mmchs3_ick: clock-mmchs3-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "mmchs3_ick";
+			clocks = <&core_l4_ick>;
+			ti,bit-shift = <30>;
+		};
 	};
 
-	mmchs3_fck: mmchs3_fck@a00 {
-		#clock-cells = <0>;
-		compatible = "ti,wait-gate-clock";
-		clocks = <&core_96m_fck>;
-		reg = <0x0a00>;
-		ti,bit-shift = <30>;
+	clock@a00 {
+		compatible = "ti,clksel";
+		reg = <0xa00>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
+
+		mmchs3_fck: clock-mmchs3-fck {
+			#clock-cells = <0>;
+			compatible = "ti,wait-gate-clock";
+			clock-output-names = "mmchs3_fck";
+			clocks = <&core_96m_fck>;
+			ti,bit-shift = <30>;
+		};
 	};
 
-	dss1_alwon_fck: dss1_alwon_fck_3430es2@e00 {
-		#clock-cells = <0>;
-		compatible = "ti,dss-gate-clock";
-		clocks = <&dpll4_m4x2_ck>;
-		ti,bit-shift = <0>;
-		reg = <0x0e00>;
-		ti,set-rate-parent;
+	clock@e00 {
+		compatible = "ti,clksel";
+		reg = <0xe00>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
+
+		dss1_alwon_fck: clock-dss1-alwon-fck-3430es2 {
+			#clock-cells = <0>;
+			compatible = "ti,dss-gate-clock";
+			clock-output-names = "dss1_alwon_fck_3430es2";
+			clocks = <&dpll4_m4x2_ck>;
+			ti,bit-shift = <0>;
+			ti,set-rate-parent;
+		};
 	};
 
 	dss_ick: dss_ick_3430es2@e10 {
diff --git a/arch/arm/boot/dts/omap36xx-clocks.dtsi b/arch/arm/boot/dts/omap36xx-clocks.dtsi
index 4e9cc9003594..c5fdb2bd765d 100644
--- a/arch/arm/boot/dts/omap36xx-clocks.dtsi
+++ b/arch/arm/boot/dts/omap36xx-clocks.dtsi
@@ -58,12 +58,19 @@
 		ti,set-bit-to-disable;
 	};
 
-	uart4_fck: uart4_fck@1000 {
-		#clock-cells = <0>;
-		compatible = "ti,wait-gate-clock";
-		clocks = <&per_48m_fck>;
+	clock@1000 {
+		compatible = "ti,clksel";
 		reg = <0x1000>;
-		ti,bit-shift = <18>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
+
+		uart4_fck: clock-uart4-fck {
+			#clock-cells = <0>;
+			compatible = "ti,wait-gate-clock";
+			clock-output-names = "uart4_fck";
+			clocks = <&per_48m_fck>;
+			ti,bit-shift = <18>;
+		};
 	};
 };
 
diff --git a/arch/arm/boot/dts/omap36xx-omap3430es2plus-clocks.dtsi b/arch/arm/boot/dts/omap36xx-omap3430es2plus-clocks.dtsi
index 945537aee3ca..c94eb86d3da7 100644
--- a/arch/arm/boot/dts/omap36xx-omap3430es2plus-clocks.dtsi
+++ b/arch/arm/boot/dts/omap36xx-omap3430es2plus-clocks.dtsi
@@ -5,21 +5,35 @@
  * Copyright (C) 2013 Texas Instruments, Inc.
  */
 &cm_clocks {
-	ssi_ssr_gate_fck_3430es2: ssi_ssr_gate_fck_3430es2@a00 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-no-wait-gate-clock";
-		clocks = <&corex2_fck>;
-		ti,bit-shift = <0>;
-		reg = <0x0a00>;
-	};
-
-	ssi_ssr_div_fck_3430es2: ssi_ssr_div_fck_3430es2@a40 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-divider-clock";
-		clocks = <&corex2_fck>;
-		ti,bit-shift = <8>;
-		reg = <0x0a40>;
-		ti,dividers = <0>, <1>, <2>, <3>, <4>, <0>, <6>, <0>, <8>;
+	clock@a00 {
+		compatible = "ti,clksel";
+		reg = <0xa00>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
+
+		ssi_ssr_gate_fck_3430es2: clock-ssi-ssr-gate-fck-3430es2 {
+			#clock-cells = <0>;
+			compatible = "ti,composite-no-wait-gate-clock";
+			clock-output-names = "ssi_ssr_gate_fck_3430es2";
+			clocks = <&corex2_fck>;
+			ti,bit-shift = <0>;
+		};
+	};
+
+	clock@a40 {
+		compatible = "ti,clksel";
+		reg = <0xa40>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
+
+		ssi_ssr_div_fck_3430es2: clock-ssi-ssr-div-fck-3430es2 {
+			#clock-cells = <0>;
+			compatible = "ti,composite-divider-clock";
+			clock-output-names = "ssi_ssr_div_fck_3430es2";
+			clocks = <&corex2_fck>;
+			ti,bit-shift = <8>;
+			ti,dividers = <0>, <1>, <2>, <3>, <4>, <0>, <6>, <0>, <8>;
+		};
 	};
 
 	ssi_ssr_fck: ssi_ssr_fck_3430es2 {
@@ -36,12 +50,27 @@
 		clock-div = <2>;
 	};
 
-	hsotgusb_ick_3430es2: hsotgusb_ick_3430es2@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-hsotgusb-interface-clock";
-		clocks = <&core_l3_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <4>;
+	clock@a10 {
+		compatible = "ti,clksel";
+		reg = <0xa10>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
+
+		hsotgusb_ick_3430es2: clock-hsotgusb-ick-3430es2 {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-hsotgusb-interface-clock";
+			clock-output-names = "hsotgusb_ick_3430es2";
+			clocks = <&core_l3_ick>;
+			ti,bit-shift = <4>;
+		};
+
+		ssi_ick: clock-ssi-ick-3430es2 {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-ssi-interface-clock";
+			clock-output-names = "ssi_ick_3430es2";
+			clocks = <&ssi_l4_ick>;
+			ti,bit-shift = <0>;
+		};
 	};
 
 	ssi_l4_ick: ssi_l4_ick {
@@ -52,20 +81,19 @@
 		clock-div = <1>;
 	};
 
-	ssi_ick: ssi_ick_3430es2@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-ssi-interface-clock";
-		clocks = <&ssi_l4_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <0>;
-	};
+	clock@c00 {
+		compatible = "ti,clksel";
+		reg = <0xc00>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
 
-	usim_gate_fck: usim_gate_fck@c00 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-gate-clock";
-		clocks = <&omap_96m_fck>;
-		ti,bit-shift = <9>;
-		reg = <0x0c00>;
+		usim_gate_fck: clock-usim-gate-fck {
+			#clock-cells = <0>;
+			compatible = "ti,composite-gate-clock";
+			clock-output-names = "usim_gate_fck";
+			clocks = <&omap_96m_fck>;
+			ti,bit-shift = <9>;
+		};
 	};
 
 	sys_d2_ck: sys_d2_ck {
@@ -140,13 +168,20 @@
 		clock-div = <20>;
 	};
 
-	usim_mux_fck: usim_mux_fck@c40 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-mux-clock";
-		clocks = <&sys_ck>, <&sys_d2_ck>, <&omap_96m_d2_fck>, <&omap_96m_d4_fck>, <&omap_96m_d8_fck>, <&omap_96m_d10_fck>, <&dpll5_m2_d4_ck>, <&dpll5_m2_d8_ck>, <&dpll5_m2_d16_ck>, <&dpll5_m2_d20_ck>;
-		ti,bit-shift = <3>;
-		reg = <0x0c40>;
-		ti,index-starts-at-one;
+	clock@c40 {
+		compatible = "ti,clksel";
+		reg = <0xc40>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
+
+		usim_mux_fck: clock-usim-mux-fck {
+			#clock-cells = <0>;
+			compatible = "ti,composite-mux-clock";
+			clock-output-names = "usim_mux_fck";
+			clocks = <&sys_ck>, <&sys_d2_ck>, <&omap_96m_d2_fck>, <&omap_96m_d4_fck>, <&omap_96m_d8_fck>, <&omap_96m_d10_fck>, <&dpll5_m2_d4_ck>, <&dpll5_m2_d8_ck>, <&dpll5_m2_d16_ck>, <&dpll5_m2_d20_ck>;
+			ti,bit-shift = <3>;
+			ti,index-starts-at-one;
+		};
 	};
 
 	usim_fck: usim_fck {
@@ -155,12 +190,19 @@
 		clocks = <&usim_gate_fck>, <&usim_mux_fck>;
 	};
 
-	usim_ick: usim_ick@c10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&wkup_l4_ick>;
-		reg = <0x0c10>;
-		ti,bit-shift = <9>;
+	clock@c10 {
+		compatible = "ti,clksel";
+		reg = <0xc10>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
+
+		usim_ick: clock-usim-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "usim_ick";
+			clocks = <&wkup_l4_ick>;
+			ti,bit-shift = <9>;
+		};
 	};
 };
 
diff --git a/arch/arm/boot/dts/omap36xx.dtsi b/arch/arm/boot/dts/omap36xx.dtsi
index 22b33098b1a2..32ac7924a130 100644
--- a/arch/arm/boot/dts/omap36xx.dtsi
+++ b/arch/arm/boot/dts/omap36xx.dtsi
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Device Tree Source for OMAP3 SoC
  *
  * Copyright (C) 2012 Texas Instruments Incorporated - https://www.ti.com/
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2.  This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
  */
 
 #include <dt-bindings/bus/ti-sysc.h>
diff --git a/arch/arm/boot/dts/omap3xxx-clocks.dtsi b/arch/arm/boot/dts/omap3xxx-clocks.dtsi
index 0656c32439d2..2e13ca11ceea 100644
--- a/arch/arm/boot/dts/omap3xxx-clocks.dtsi
+++ b/arch/arm/boot/dts/omap3xxx-clocks.dtsi
@@ -78,12 +78,35 @@
 };
 
 &scm_clocks {
-	mcbsp5_mux_fck: mcbsp5_mux_fck@68 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-mux-clock";
-		clocks = <&core_96m_fck>, <&mcbsp_clks>;
-		ti,bit-shift = <4>;
+	/* CONTROL_DEVCONF1 */
+	clock@68 {
+		compatible = "ti,clksel";
 		reg = <0x68>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
+
+		mcbsp5_mux_fck: clock-mcbsp5-mux-fck {
+			#clock-cells = <0>;
+			compatible = "ti,composite-mux-clock";
+			clock-output-names = "mcbsp5_mux_fck";
+			clocks = <&core_96m_fck>, <&mcbsp_clks>;
+			ti,bit-shift = <4>;
+		};
+
+		mcbsp3_mux_fck: clock-mcbsp3-mux-fck {
+			#clock-cells = <0>;
+			compatible = "ti,composite-mux-clock";
+			clock-output-names = "mcbsp3_mux_fck";
+			clocks = <&per_96m_fck>, <&mcbsp_clks>;
+		};
+
+		mcbsp4_mux_fck: clock-mcbsp4-mux-fck {
+			#clock-cells = <0>;
+			compatible = "ti,composite-mux-clock";
+			clock-output-names = "mcbsp4_mux_fck";
+			clocks = <&per_96m_fck>, <&mcbsp_clks>;
+			ti,bit-shift = <2>;
+		};
 	};
 
 	mcbsp5_fck: mcbsp5_fck {
@@ -92,12 +115,28 @@
 		clocks = <&mcbsp5_gate_fck>, <&mcbsp5_mux_fck>;
 	};
 
-	mcbsp1_mux_fck: mcbsp1_mux_fck@4 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-mux-clock";
-		clocks = <&core_96m_fck>, <&mcbsp_clks>;
-		ti,bit-shift = <2>;
-		reg = <0x04>;
+	/* CONTROL_DEVCONF0 */
+	clock@4 {
+		compatible = "ti,clksel";
+		reg = <0x4>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
+
+		mcbsp1_mux_fck: clock-mcbsp1-mux-fck {
+			#clock-cells = <0>;
+			compatible = "ti,composite-mux-clock";
+			clock-output-names = "mcbsp1_mux_fck";
+			clocks = <&core_96m_fck>, <&mcbsp_clks>;
+			ti,bit-shift = <2>;
+		};
+
+		mcbsp2_mux_fck: clock-mcbsp2-mux-fck {
+			#clock-cells = <0>;
+			compatible = "ti,composite-mux-clock";
+			clock-output-names = "mcbsp2_mux_fck";
+			clocks = <&per_96m_fck>, <&mcbsp_clks>;
+			ti,bit-shift = <6>;
+		};
 	};
 
 	mcbsp1_fck: mcbsp1_fck {
@@ -106,41 +145,18 @@
 		clocks = <&mcbsp1_gate_fck>, <&mcbsp1_mux_fck>;
 	};
 
-	mcbsp2_mux_fck: mcbsp2_mux_fck@4 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-mux-clock";
-		clocks = <&per_96m_fck>, <&mcbsp_clks>;
-		ti,bit-shift = <6>;
-		reg = <0x04>;
-	};
-
 	mcbsp2_fck: mcbsp2_fck {
 		#clock-cells = <0>;
 		compatible = "ti,composite-clock";
 		clocks = <&mcbsp2_gate_fck>, <&mcbsp2_mux_fck>;
 	};
 
-	mcbsp3_mux_fck: mcbsp3_mux_fck@68 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-mux-clock";
-		clocks = <&per_96m_fck>, <&mcbsp_clks>;
-		reg = <0x68>;
-	};
-
 	mcbsp3_fck: mcbsp3_fck {
 		#clock-cells = <0>;
 		compatible = "ti,composite-clock";
 		clocks = <&mcbsp3_gate_fck>, <&mcbsp3_mux_fck>;
 	};
 
-	mcbsp4_mux_fck: mcbsp4_mux_fck@68 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-mux-clock";
-		clocks = <&per_96m_fck>, <&mcbsp_clks>;
-		ti,bit-shift = <2>;
-		reg = <0x68>;
-	};
-
 	mcbsp4_fck: mcbsp4_fck {
 		#clock-cells = <0>;
 		compatible = "ti,composite-clock";
@@ -238,14 +254,87 @@
 		reg = <0x0d00>, <0x0d20>, <0x0d40>, <0x0d30>;
 	};
 
-	dpll3_m3_ck: dpll3_m3_ck@1140 {
-		#clock-cells = <0>;
-		compatible = "ti,divider-clock";
-		clocks = <&dpll3_ck>;
-		ti,bit-shift = <16>;
-		ti,max-div = <31>;
+	/* CM_CLKSEL1_EMU */
+	clock@1140 {
+		compatible = "ti,clksel";
 		reg = <0x1140>;
-		ti,index-starts-at-one;
+		#clock-cells = <2>;
+		#address-cells = <0>;
+
+		dpll3_m3_ck: clock-dpll3-m3 {
+			#clock-cells = <0>;
+			compatible = "ti,divider-clock";
+			clock-output-names = "dpll3_m3_ck";
+			clocks = <&dpll3_ck>;
+			ti,bit-shift = <16>;
+			ti,max-div = <31>;
+			ti,index-starts-at-one;
+		};
+
+		dpll4_m6_ck: clock-dpll4-m6 {
+			#clock-cells = <0>;
+			compatible = "ti,divider-clock";
+			clock-output-names = "dpll4_m6_ck";
+			clocks = <&dpll4_ck>;
+			ti,bit-shift = <24>;
+			ti,max-div = <63>;
+			ti,index-starts-at-one;
+		};
+
+		emu_src_mux_ck: clock-emu-src-mux {
+			#clock-cells = <0>;
+			compatible = "ti,mux-clock";
+			clock-output-names = "emu_src_mux_ck";
+			clocks = <&sys_ck>, <&emu_core_alwon_ck>, <&emu_per_alwon_ck>, <&emu_mpu_alwon_ck>;
+		};
+
+		pclk_fck: clock-pclk-fck {
+			#clock-cells = <0>;
+			compatible = "ti,divider-clock";
+			clock-output-names = "pclk_fck";
+			clocks = <&emu_src_ck>;
+			ti,bit-shift = <8>;
+			ti,max-div = <7>;
+			ti,index-starts-at-one;
+		};
+
+		pclkx2_fck: clock-pclkx2-fck {
+			#clock-cells = <0>;
+			compatible = "ti,divider-clock";
+			clock-output-names = "pclkx2_fck";
+			clocks = <&emu_src_ck>;
+			ti,bit-shift = <6>;
+			ti,max-div = <3>;
+			ti,index-starts-at-one;
+		};
+
+		atclk_fck: clock-atclk-fck {
+			#clock-cells = <0>;
+			compatible = "ti,divider-clock";
+			clock-output-names = "atclk_fck";
+			clocks = <&emu_src_ck>;
+			ti,bit-shift = <4>;
+			ti,max-div = <3>;
+			ti,index-starts-at-one;
+		};
+
+		traceclk_src_fck: clock-traceclk-src-fck {
+			#clock-cells = <0>;
+			compatible = "ti,mux-clock";
+			clock-output-names = "traceclk_src_fck";
+			clocks = <&sys_ck>, <&emu_core_alwon_ck>, <&emu_per_alwon_ck>, <&emu_mpu_alwon_ck>;
+			ti,bit-shift = <2>;
+		};
+
+		traceclk_fck: clock-traceclk-fck {
+			#clock-cells = <0>;
+			compatible = "ti,divider-clock";
+			clock-output-names = "traceclk_fck";
+			clocks = <&traceclk_src_fck>;
+			ti,bit-shift = <11>;
+			ti,max-div = <7>;
+			ti,index-starts-at-one;
+		};
 	};
 
 	dpll3_m3x2_mul_ck: dpll3_m3x2_mul_ck {
@@ -285,16 +374,6 @@
 		clock-frequency = <0x0>;
 	};
 
-	dpll3_m2_ck: dpll3_m2_ck@d40 {
-		#clock-cells = <0>;
-		compatible = "ti,divider-clock";
-		clocks = <&dpll3_ck>;
-		ti,bit-shift = <27>;
-		ti,max-div = <31>;
-		reg = <0x0d40>;
-		ti,index-starts-at-one;
-	};
-
 	core_ck: core_ck {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
@@ -345,22 +424,73 @@
 		clock-div = <1>;
 	};
 
-	omap_96m_fck: omap_96m_fck@d40 {
-		#clock-cells = <0>;
-		compatible = "ti,mux-clock";
-		clocks = <&cm_96m_fck>, <&sys_ck>;
-		ti,bit-shift = <6>;
-		reg = <0x0d40>;
-	};
-
-	dpll4_m3_ck: dpll4_m3_ck@e40 {
-		#clock-cells = <0>;
-		compatible = "ti,divider-clock";
-		clocks = <&dpll4_ck>;
-		ti,bit-shift = <8>;
-		ti,max-div = <32>;
-		reg = <0x0e40>;
-		ti,index-starts-at-one;
+	/* CM_CLKSEL1_PLL */
+	clock@d40 {
+		compatible = "ti,clksel";
+		reg = <0xd40>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
+
+		dpll3_m2_ck: clock-dpll3-m2 {
+			#clock-cells = <0>;
+			compatible = "ti,divider-clock";
+			clock-output-names = "dpll3_m2_ck";
+			clocks = <&dpll3_ck>;
+			ti,bit-shift = <27>;
+			ti,max-div = <31>;
+			ti,index-starts-at-one;
+		};
+
+		omap_96m_fck: clock-omap-96m-fck {
+			#clock-cells = <0>;
+			compatible = "ti,mux-clock";
+			clock-output-names = "omap_96m_fck";
+			clocks = <&cm_96m_fck>, <&sys_ck>;
+			ti,bit-shift = <6>;
+		};
+
+		omap_54m_fck: clock-omap-54m-fck {
+			#clock-cells = <0>;
+			compatible = "ti,mux-clock";
+			clock-output-names = "omap_54m_fck";
+			clocks = <&dpll4_m3x2_ck>, <&sys_altclk>;
+			ti,bit-shift = <5>;
+		};
+
+		omap_48m_fck: clock-omap-48m-fck {
+			#clock-cells = <0>;
+			compatible = "ti,mux-clock";
+			clock-output-names = "omap_48m_fck";
+			clocks = <&cm_96m_d2_fck>, <&sys_altclk>;
+			ti,bit-shift = <3>;
+		};
+	};
+
+	/* CM_CLKSEL_DSS */
+	clock@e40 {
+		compatible = "ti,clksel";
+		reg = <0xe40>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
+
+		dpll4_m3_ck: clock-dpll4-m3 {
+			#clock-cells = <0>;
+			compatible = "ti,divider-clock";
+			clock-output-names = "dpll4_m3_ck";
+			clocks = <&dpll4_ck>;
+			ti,bit-shift = <8>;
+			ti,max-div = <32>;
+			ti,index-starts-at-one;
+		};
+
+		dpll4_m4_ck: clock-dpll4-m4 {
+			#clock-cells = <0>;
+			compatible = "ti,divider-clock";
+			clock-output-names = "dpll4_m4_ck";
+			clocks = <&dpll4_ck>;
+			ti,max-div = <16>;
+			ti,index-starts-at-one;
+		};
 	};
 
 	dpll4_m3x2_mul_ck: dpll4_m3x2_mul_ck {
@@ -380,14 +510,6 @@
 		ti,set-bit-to-disable;
 	};
 
-	omap_54m_fck: omap_54m_fck@d40 {
-		#clock-cells = <0>;
-		compatible = "ti,mux-clock";
-		clocks = <&dpll4_m3x2_ck>, <&sys_altclk>;
-		ti,bit-shift = <5>;
-		reg = <0x0d40>;
-	};
-
 	cm_96m_d2_fck: cm_96m_d2_fck {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
@@ -396,14 +518,6 @@
 		clock-div = <2>;
 	};
 
-	omap_48m_fck: omap_48m_fck@d40 {
-		#clock-cells = <0>;
-		compatible = "ti,mux-clock";
-		clocks = <&cm_96m_d2_fck>, <&sys_altclk>;
-		ti,bit-shift = <3>;
-		reg = <0x0d40>;
-	};
-
 	omap_12m_fck: omap_12m_fck {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
@@ -412,15 +526,6 @@
 		clock-div = <4>;
 	};
 
-	dpll4_m4_ck: dpll4_m4_ck@e40 {
-		#clock-cells = <0>;
-		compatible = "ti,divider-clock";
-		clocks = <&dpll4_ck>;
-		ti,max-div = <16>;
-		reg = <0x0e40>;
-		ti,index-starts-at-one;
-	};
-
 	dpll4_m4x2_mul_ck: dpll4_m4x2_mul_ck {
 		#clock-cells = <0>;
 		compatible = "ti,fixed-factor-clock";
@@ -468,16 +573,6 @@
 		ti,set-rate-parent;
 	};
 
-	dpll4_m6_ck: dpll4_m6_ck@1140 {
-		#clock-cells = <0>;
-		compatible = "ti,divider-clock";
-		clocks = <&dpll4_ck>;
-		ti,bit-shift = <24>;
-		ti,max-div = <63>;
-		reg = <0x1140>;
-		ti,index-starts-at-one;
-	};
-
 	dpll4_m6x2_mul_ck: dpll4_m6x2_mul_ck {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
@@ -503,19 +598,37 @@
 		clock-div = <1>;
 	};
 
-	clkout2_src_gate_ck: clkout2_src_gate_ck@d70 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-no-wait-gate-clock";
-		clocks = <&core_ck>;
-		ti,bit-shift = <7>;
-		reg = <0x0d70>;
-	};
-
-	clkout2_src_mux_ck: clkout2_src_mux_ck@d70 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-mux-clock";
-		clocks = <&core_ck>, <&sys_ck>, <&cm_96m_fck>, <&omap_54m_fck>;
-		reg = <0x0d70>;
+	/* CM_CLKOUT_CTRL */
+	clock@d70 {
+		compatible = "ti,clksel";
+		reg = <0xd70>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
+
+		clkout2_src_gate_ck: clock-clkout2-src-gate {
+			#clock-cells = <0>;
+			compatible = "ti,composite-no-wait-gate-clock";
+			clock-output-names = "clkout2_src_gate_ck";
+			clocks = <&core_ck>;
+			ti,bit-shift = <7>;
+		};
+
+		clkout2_src_mux_ck: clock-clkout2-src-mux {
+			#clock-cells = <0>;
+			compatible = "ti,composite-mux-clock";
+			clock-output-names = "clkout2_src_mux_ck";
+			clocks = <&core_ck>, <&sys_ck>, <&cm_96m_fck>, <&omap_54m_fck>;
+		};
+
+		sys_clkout2: clock-sys-clkout2 {
+			#clock-cells = <0>;
+			compatible = "ti,divider-clock";
+			clock-output-names = "sys_clkout2";
+			clocks = <&clkout2_src_ck>;
+			ti,bit-shift = <3>;
+			ti,max-div = <64>;
+			ti,index-power-of-two;
+		};
 	};
 
 	clkout2_src_ck: clkout2_src_ck {
@@ -524,16 +637,6 @@
 		clocks = <&clkout2_src_gate_ck>, <&clkout2_src_mux_ck>;
 	};
 
-	sys_clkout2: sys_clkout2@d70 {
-		#clock-cells = <0>;
-		compatible = "ti,divider-clock";
-		clocks = <&clkout2_src_ck>;
-		ti,bit-shift = <3>;
-		ti,max-div = <64>;
-		reg = <0x0d70>;
-		ti,index-power-of-two;
-	};
-
 	mpu_ck: mpu_ck {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
@@ -558,49 +661,208 @@
 		clock-div = <1>;
 	};
 
-	l3_ick: l3_ick@a40 {
-		#clock-cells = <0>;
-		compatible = "ti,divider-clock";
-		clocks = <&core_ck>;
-		ti,max-div = <3>;
-		reg = <0x0a40>;
-		ti,index-starts-at-one;
-	};
-
-	l4_ick: l4_ick@a40 {
-		#clock-cells = <0>;
-		compatible = "ti,divider-clock";
-		clocks = <&l3_ick>;
-		ti,bit-shift = <2>;
-		ti,max-div = <3>;
-		reg = <0x0a40>;
-		ti,index-starts-at-one;
-	};
-
-	rm_ick: rm_ick@c40 {
-		#clock-cells = <0>;
-		compatible = "ti,divider-clock";
-		clocks = <&l4_ick>;
-		ti,bit-shift = <1>;
-		ti,max-div = <3>;
-		reg = <0x0c40>;
-		ti,index-starts-at-one;
-	};
-
-	gpt10_gate_fck: gpt10_gate_fck@a00 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-gate-clock";
-		clocks = <&sys_ck>;
-		ti,bit-shift = <11>;
-		reg = <0x0a00>;
-	};
-
-	gpt10_mux_fck: gpt10_mux_fck@a40 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-mux-clock";
-		clocks = <&omap_32k_fck>, <&sys_ck>;
-		ti,bit-shift = <6>;
-		reg = <0x0a40>;
+	/* CM_CLKSEL_CORE */
+	clock@a40 {
+		compatible = "ti,clksel";
+		reg = <0xa40>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
+
+		l3_ick: clock-l3-ick {
+			#clock-cells = <0>;
+			compatible = "ti,divider-clock";
+			clock-output-names = "l3_ick";
+			clocks = <&core_ck>;
+			ti,max-div = <3>;
+			ti,index-starts-at-one;
+		};
+
+		l4_ick: clock-l4-ick {
+			#clock-cells = <0>;
+			compatible = "ti,divider-clock";
+			clock-output-names = "l4_ick";
+			clocks = <&l3_ick>;
+			ti,bit-shift = <2>;
+			ti,max-div = <3>;
+			ti,index-starts-at-one;
+		};
+
+		gpt10_mux_fck: clock-gpt10-mux-fck {
+			#clock-cells = <0>;
+			compatible = "ti,composite-mux-clock";
+			clock-output-names = "gpt10_mux_fck";
+			clocks = <&omap_32k_fck>, <&sys_ck>;
+			ti,bit-shift = <6>;
+		};
+
+		gpt11_mux_fck: clock-gpt11-mux-fck {
+			#clock-cells = <0>;
+			compatible = "ti,composite-mux-clock";
+			clock-output-names = "gpt11_mux_fck";
+			clocks = <&omap_32k_fck>, <&sys_ck>;
+			ti,bit-shift = <7>;
+		};
+	};
+
+	/* CM_CLKSEL_WKUP */
+	clock@c40 {
+		compatible = "ti,clksel";
+		reg = <0xc40>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
+
+		rm_ick: clock-rm-ick {
+			#clock-cells = <0>;
+			compatible = "ti,divider-clock";
+			clock-output-names = "rm_ick";
+			clocks = <&l4_ick>;
+			ti,bit-shift = <1>;
+			ti,max-div = <3>;
+			ti,index-starts-at-one;
+		};
+
+		gpt1_mux_fck: clock-gpt1-mux-fck {
+			#clock-cells = <0>;
+			compatible = "ti,composite-mux-clock";
+			clock-output-names = "gpt1_mux_fck";
+			clocks = <&omap_32k_fck>, <&sys_ck>;
+		};
+	};
+
+	/* CM_FCLKEN1_CORE */
+	clock@a00 {
+		compatible = "ti,clksel";
+		reg = <0xa00>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
+
+		gpt10_gate_fck: clock-gpt10-gate-fck {
+			#clock-cells = <0>;
+			compatible = "ti,composite-gate-clock";
+			clock-output-names = "gpt10_gate_fck";
+			clocks = <&sys_ck>;
+			ti,bit-shift = <11>;
+		};
+
+		gpt11_gate_fck: clock-gpt11-gate-fck {
+			#clock-cells = <0>;
+			compatible = "ti,composite-gate-clock";
+			clock-output-names = "gpt11_gate_fck";
+			clocks = <&sys_ck>;
+			ti,bit-shift = <12>;
+		};
+
+		mmchs2_fck: clock-mmchs2-fck {
+			#clock-cells = <0>;
+			compatible = "ti,wait-gate-clock";
+			clock-output-names = "mmchs2_fck";
+			clocks = <&core_96m_fck>;
+			ti,bit-shift = <25>;
+		};
+
+		mmchs1_fck: clock-mmchs1-fck {
+			#clock-cells = <0>;
+			compatible = "ti,wait-gate-clock";
+			clock-output-names = "mmchs1_fck";
+			clocks = <&core_96m_fck>;
+			ti,bit-shift = <24>;
+		};
+
+		i2c3_fck: clock-i2c3-fck {
+			#clock-cells = <0>;
+			compatible = "ti,wait-gate-clock";
+			clock-output-names = "i2c3_fck";
+			clocks = <&core_96m_fck>;
+			ti,bit-shift = <17>;
+		};
+
+		i2c2_fck: clock-i2c2-fck {
+			#clock-cells = <0>;
+			compatible = "ti,wait-gate-clock";
+			clock-output-names = "i2c2_fck";
+			clocks = <&core_96m_fck>;
+			ti,bit-shift = <16>;
+		};
+
+		i2c1_fck: clock-i2c1-fck {
+			#clock-cells = <0>;
+			compatible = "ti,wait-gate-clock";
+			clock-output-names = "i2c1_fck";
+			clocks = <&core_96m_fck>;
+			ti,bit-shift = <15>;
+		};
+
+		mcbsp5_gate_fck: clock-mcbsp5-gate-fck {
+			#clock-cells = <0>;
+			compatible = "ti,composite-gate-clock";
+			clock-output-names = "mcbsp5_gate_fck";
+			clocks = <&mcbsp_clks>;
+			ti,bit-shift = <10>;
+		};
+
+		mcbsp1_gate_fck: clock-mcbsp1-gate-fck {
+			#clock-cells = <0>;
+			compatible = "ti,composite-gate-clock";
+			clock-output-names = "mcbsp1_gate_fck";
+			clocks = <&mcbsp_clks>;
+			ti,bit-shift = <9>;
+		};
+
+		mcspi4_fck: clock-mcspi4-fck {
+			#clock-cells = <0>;
+			compatible = "ti,wait-gate-clock";
+			clock-output-names = "mcspi4_fck";
+			clocks = <&core_48m_fck>;
+			ti,bit-shift = <21>;
+		};
+
+		mcspi3_fck: clock-mcspi3-fck {
+			#clock-cells = <0>;
+			compatible = "ti,wait-gate-clock";
+			clock-output-names = "mcspi3_fck";
+			clocks = <&core_48m_fck>;
+			ti,bit-shift = <20>;
+		};
+
+		mcspi2_fck: clock-mcspi2-fck {
+			#clock-cells = <0>;
+			compatible = "ti,wait-gate-clock";
+			clock-output-names = "mcspi2_fck";
+			clocks = <&core_48m_fck>;
+			ti,bit-shift = <19>;
+		};
+
+		mcspi1_fck: clock-mcspi1-fck {
+			#clock-cells = <0>;
+			compatible = "ti,wait-gate-clock";
+			clock-output-names = "mcspi1_fck";
+			clocks = <&core_48m_fck>;
+			ti,bit-shift = <18>;
+		};
+
+		uart2_fck: clock-uart2-fck {
+			#clock-cells = <0>;
+			compatible = "ti,wait-gate-clock";
+			clock-output-names = "uart2_fck";
+			clocks = <&core_48m_fck>;
+			ti,bit-shift = <14>;
+		};
+
+		uart1_fck: clock-uart1-fck {
+			#clock-cells = <0>;
+			compatible = "ti,wait-gate-clock";
+			clock-output-names = "uart1_fck";
+			clocks = <&core_48m_fck>;
+			ti,bit-shift = <13>;
+		};
+
+		hdq_fck: clock-hdq-fck {
+			#clock-cells = <0>;
+			compatible = "ti,wait-gate-clock";
+			clock-output-names = "hdq_fck";
+			clocks = <&core_12m_fck>;
+			ti,bit-shift = <22>;
+		};
 	};
 
 	gpt10_fck: gpt10_fck {
@@ -609,22 +871,6 @@
 		clocks = <&gpt10_gate_fck>, <&gpt10_mux_fck>;
 	};
 
-	gpt11_gate_fck: gpt11_gate_fck@a00 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-gate-clock";
-		clocks = <&sys_ck>;
-		ti,bit-shift = <12>;
-		reg = <0x0a00>;
-	};
-
-	gpt11_mux_fck: gpt11_mux_fck@a40 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-mux-clock";
-		clocks = <&omap_32k_fck>, <&sys_ck>;
-		ti,bit-shift = <7>;
-		reg = <0x0a40>;
-	};
-
 	gpt11_fck: gpt11_fck {
 		#clock-cells = <0>;
 		compatible = "ti,composite-clock";
@@ -639,62 +885,6 @@
 		clock-div = <1>;
 	};
 
-	mmchs2_fck: mmchs2_fck@a00 {
-		#clock-cells = <0>;
-		compatible = "ti,wait-gate-clock";
-		clocks = <&core_96m_fck>;
-		reg = <0x0a00>;
-		ti,bit-shift = <25>;
-	};
-
-	mmchs1_fck: mmchs1_fck@a00 {
-		#clock-cells = <0>;
-		compatible = "ti,wait-gate-clock";
-		clocks = <&core_96m_fck>;
-		reg = <0x0a00>;
-		ti,bit-shift = <24>;
-	};
-
-	i2c3_fck: i2c3_fck@a00 {
-		#clock-cells = <0>;
-		compatible = "ti,wait-gate-clock";
-		clocks = <&core_96m_fck>;
-		reg = <0x0a00>;
-		ti,bit-shift = <17>;
-	};
-
-	i2c2_fck: i2c2_fck@a00 {
-		#clock-cells = <0>;
-		compatible = "ti,wait-gate-clock";
-		clocks = <&core_96m_fck>;
-		reg = <0x0a00>;
-		ti,bit-shift = <16>;
-	};
-
-	i2c1_fck: i2c1_fck@a00 {
-		#clock-cells = <0>;
-		compatible = "ti,wait-gate-clock";
-		clocks = <&core_96m_fck>;
-		reg = <0x0a00>;
-		ti,bit-shift = <15>;
-	};
-
-	mcbsp5_gate_fck: mcbsp5_gate_fck@a00 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-gate-clock";
-		clocks = <&mcbsp_clks>;
-		ti,bit-shift = <10>;
-		reg = <0x0a00>;
-	};
-
-	mcbsp1_gate_fck: mcbsp1_gate_fck@a00 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-gate-clock";
-		clocks = <&mcbsp_clks>;
-		ti,bit-shift = <9>;
-		reg = <0x0a00>;
-	};
-
 	core_48m_fck: core_48m_fck {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
@@ -703,54 +893,6 @@
 		clock-div = <1>;
 	};
 
-	mcspi4_fck: mcspi4_fck@a00 {
-		#clock-cells = <0>;
-		compatible = "ti,wait-gate-clock";
-		clocks = <&core_48m_fck>;
-		reg = <0x0a00>;
-		ti,bit-shift = <21>;
-	};
-
-	mcspi3_fck: mcspi3_fck@a00 {
-		#clock-cells = <0>;
-		compatible = "ti,wait-gate-clock";
-		clocks = <&core_48m_fck>;
-		reg = <0x0a00>;
-		ti,bit-shift = <20>;
-	};
-
-	mcspi2_fck: mcspi2_fck@a00 {
-		#clock-cells = <0>;
-		compatible = "ti,wait-gate-clock";
-		clocks = <&core_48m_fck>;
-		reg = <0x0a00>;
-		ti,bit-shift = <19>;
-	};
-
-	mcspi1_fck: mcspi1_fck@a00 {
-		#clock-cells = <0>;
-		compatible = "ti,wait-gate-clock";
-		clocks = <&core_48m_fck>;
-		reg = <0x0a00>;
-		ti,bit-shift = <18>;
-	};
-
-	uart2_fck: uart2_fck@a00 {
-		#clock-cells = <0>;
-		compatible = "ti,wait-gate-clock";
-		clocks = <&core_48m_fck>;
-		reg = <0x0a00>;
-		ti,bit-shift = <14>;
-	};
-
-	uart1_fck: uart1_fck@a00 {
-		#clock-cells = <0>;
-		compatible = "ti,wait-gate-clock";
-		clocks = <&core_48m_fck>;
-		reg = <0x0a00>;
-		ti,bit-shift = <13>;
-	};
-
 	core_12m_fck: core_12m_fck {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
@@ -759,14 +901,6 @@
 		clock-div = <1>;
 	};
 
-	hdq_fck: hdq_fck@a00 {
-		#clock-cells = <0>;
-		compatible = "ti,wait-gate-clock";
-		clocks = <&core_12m_fck>;
-		reg = <0x0a00>;
-		ti,bit-shift = <22>;
-	};
-
 	core_l3_ick: core_l3_ick {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
@@ -775,12 +909,172 @@
 		clock-div = <1>;
 	};
 
-	sdrc_ick: sdrc_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,wait-gate-clock";
-		clocks = <&core_l3_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <1>;
+	/* CM_ICLKEN1_CORE */
+	clock@a10 {
+		compatible = "ti,clksel";
+		reg = <0xa10>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
+
+		sdrc_ick: clock-sdrc-ick {
+			#clock-cells = <0>;
+			compatible = "ti,wait-gate-clock";
+			clock-output-names = "sdrc_ick";
+			clocks = <&core_l3_ick>;
+			ti,bit-shift = <1>;
+		};
+
+		mmchs2_ick: clock-mmchs2-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "mmchs2_ick";
+			clocks = <&core_l4_ick>;
+			ti,bit-shift = <25>;
+		};
+
+		mmchs1_ick: clock-mmchs1-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "mmchs1_ick";
+			clocks = <&core_l4_ick>;
+			ti,bit-shift = <24>;
+		};
+
+		hdq_ick: clock-hdq-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "hdq_ick";
+			clocks = <&core_l4_ick>;
+			ti,bit-shift = <22>;
+		};
+
+		mcspi4_ick: clock-mcspi4-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "mcspi4_ick";
+			clocks = <&core_l4_ick>;
+			ti,bit-shift = <21>;
+		};
+
+		mcspi3_ick: clock-mcspi3-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "mcspi3_ick";
+			clocks = <&core_l4_ick>;
+			ti,bit-shift = <20>;
+		};
+
+		mcspi2_ick: clock-mcspi2-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "mcspi2_ick";
+			clocks = <&core_l4_ick>;
+			ti,bit-shift = <19>;
+		};
+
+		mcspi1_ick: clock-mcspi1-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "mcspi1_ick";
+			clocks = <&core_l4_ick>;
+			ti,bit-shift = <18>;
+		};
+
+		i2c3_ick: clock-i2c3-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "i2c3_ick";
+			clocks = <&core_l4_ick>;
+			ti,bit-shift = <17>;
+		};
+
+		i2c2_ick: clock-i2c2-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "i2c2_ick";
+			clocks = <&core_l4_ick>;
+			ti,bit-shift = <16>;
+		};
+
+		i2c1_ick: clock-i2c1-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "i2c1_ick";
+			clocks = <&core_l4_ick>;
+			ti,bit-shift = <15>;
+		};
+
+		uart2_ick: clock-uart2-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "uart2_ick";
+			clocks = <&core_l4_ick>;
+			ti,bit-shift = <14>;
+		};
+
+		uart1_ick: clock-uart1-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "uart1_ick";
+			clocks = <&core_l4_ick>;
+			ti,bit-shift = <13>;
+		};
+
+		gpt11_ick: clock-gpt11-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "gpt11_ick";
+			clocks = <&core_l4_ick>;
+			ti,bit-shift = <12>;
+		};
+
+		gpt10_ick: clock-gpt10-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "gpt10_ick";
+			clocks = <&core_l4_ick>;
+			ti,bit-shift = <11>;
+		};
+
+		mcbsp5_ick: clock-mcbsp5-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "mcbsp5_ick";
+			clocks = <&core_l4_ick>;
+			ti,bit-shift = <10>;
+		};
+
+		mcbsp1_ick: clock-mcbsp1-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "mcbsp1_ick";
+			clocks = <&core_l4_ick>;
+			ti,bit-shift = <9>;
+		};
+
+		omapctrl_ick: clock-omapctrl-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "omapctrl_ick";
+			clocks = <&core_l4_ick>;
+			ti,bit-shift = <6>;
+		};
+
+		aes2_ick: clock-aes2-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "aes2_ick";
+			clocks = <&core_l4_ick>;
+			ti,bit-shift = <28>;
+		};
+
+		sha12_ick: clock-sha12-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "sha12_ick";
+			clocks = <&core_l4_ick>;
+			ti,bit-shift = <27>;
+		};
 	};
 
 	gpmc_fck: gpmc_fck {
@@ -799,164 +1093,36 @@
 		clock-div = <1>;
 	};
 
-	mmchs2_ick: mmchs2_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&core_l4_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <25>;
-	};
-
-	mmchs1_ick: mmchs1_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&core_l4_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <24>;
-	};
-
-	hdq_ick: hdq_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&core_l4_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <22>;
-	};
-
-	mcspi4_ick: mcspi4_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&core_l4_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <21>;
-	};
-
-	mcspi3_ick: mcspi3_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&core_l4_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <20>;
-	};
-
-	mcspi2_ick: mcspi2_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&core_l4_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <19>;
-	};
-
-	mcspi1_ick: mcspi1_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&core_l4_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <18>;
-	};
-
-	i2c3_ick: i2c3_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&core_l4_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <17>;
-	};
-
-	i2c2_ick: i2c2_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&core_l4_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <16>;
-	};
-
-	i2c1_ick: i2c1_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&core_l4_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <15>;
-	};
-
-	uart2_ick: uart2_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&core_l4_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <14>;
-	};
-
-	uart1_ick: uart1_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&core_l4_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <13>;
-	};
-
-	gpt11_ick: gpt11_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&core_l4_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <12>;
-	};
-
-	gpt10_ick: gpt10_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&core_l4_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <11>;
-	};
-
-	mcbsp5_ick: mcbsp5_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&core_l4_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <10>;
-	};
-
-	mcbsp1_ick: mcbsp1_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&core_l4_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <9>;
-	};
-
-	omapctrl_ick: omapctrl_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&core_l4_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <6>;
-	};
-
-	dss_tv_fck: dss_tv_fck@e00 {
-		#clock-cells = <0>;
-		compatible = "ti,gate-clock";
-		clocks = <&omap_54m_fck>;
-		reg = <0x0e00>;
-		ti,bit-shift = <2>;
-	};
-
-	dss_96m_fck: dss_96m_fck@e00 {
-		#clock-cells = <0>;
-		compatible = "ti,gate-clock";
-		clocks = <&omap_96m_fck>;
-		reg = <0x0e00>;
-		ti,bit-shift = <2>;
-	};
-
-	dss2_alwon_fck: dss2_alwon_fck@e00 {
-		#clock-cells = <0>;
-		compatible = "ti,gate-clock";
-		clocks = <&sys_ck>;
-		reg = <0x0e00>;
-		ti,bit-shift = <1>;
+	/* CM_FCLKEN_DSS */
+	clock@e00 {
+		compatible = "ti,clksel";
+		reg = <0xe00>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
+
+		dss_tv_fck: clock-dss-tv-fck {
+			#clock-cells = <0>;
+			compatible = "ti,gate-clock";
+			clock-output-names = "dss_tv_fck";
+			clocks = <&omap_54m_fck>;
+			ti,bit-shift = <2>;
+		};
+
+		dss_96m_fck: clock-dss-96m-fck {
+			#clock-cells = <0>;
+			compatible = "ti,gate-clock";
+			clock-output-names = "dss_96m_fck";
+			clocks = <&omap_96m_fck>;
+			ti,bit-shift = <2>;
+		};
+
+		dss2_alwon_fck: clock-dss2-alwon-fck {
+			#clock-cells = <0>;
+			compatible = "ti,gate-clock";
+			clock-output-names = "dss2_alwon_fck";
+			clocks = <&sys_ck>;
+			ti,bit-shift = <1>;
+		};
 	};
 
 	dummy_ck: dummy_ck {
@@ -965,19 +1131,36 @@
 		clock-frequency = <0>;
 	};
 
-	gpt1_gate_fck: gpt1_gate_fck@c00 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-gate-clock";
-		clocks = <&sys_ck>;
-		ti,bit-shift = <0>;
-		reg = <0x0c00>;
-	};
-
-	gpt1_mux_fck: gpt1_mux_fck@c40 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-mux-clock";
-		clocks = <&omap_32k_fck>, <&sys_ck>;
-		reg = <0x0c40>;
+	/* CM_FCLKEN_WKUP */
+	clock@c00 {
+		compatible = "ti,clksel";
+		reg = <0xc00>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
+
+		gpt1_gate_fck: clock-gpt1-gate-fck {
+			#clock-cells = <0>;
+			compatible = "ti,composite-gate-clock";
+			clock-output-names = "gpt1_gate_fck";
+			clocks = <&sys_ck>;
+			ti,bit-shift = <0>;
+		};
+
+		gpio1_dbck: clock-gpio1-dbck {
+			#clock-cells = <0>;
+			compatible = "ti,gate-clock";
+			clock-output-names = "gpio1_dbck";
+			clocks = <&wkup_32k_fck>;
+			ti,bit-shift = <3>;
+		};
+
+		wdt2_fck: clock-wdt2-fck {
+			#clock-cells = <0>;
+			compatible = "ti,wait-gate-clock";
+			clock-output-names = "wdt2_fck";
+			clocks = <&wkup_32k_fck>;
+			ti,bit-shift = <5>;
+		};
 	};
 
 	gpt1_fck: gpt1_fck {
@@ -986,14 +1169,6 @@
 		clocks = <&gpt1_gate_fck>, <&gpt1_mux_fck>;
 	};
 
-	aes2_ick: aes2_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&core_l4_ick>;
-		ti,bit-shift = <28>;
-		reg = <0x0a10>;
-	};
-
 	wkup_32k_fck: wkup_32k_fck {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
@@ -1002,76 +1177,60 @@
 		clock-div = <1>;
 	};
 
-	gpio1_dbck: gpio1_dbck@c00 {
-		#clock-cells = <0>;
-		compatible = "ti,gate-clock";
-		clocks = <&wkup_32k_fck>;
-		reg = <0x0c00>;
-		ti,bit-shift = <3>;
-	};
-
-	sha12_ick: sha12_ick@a10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&core_l4_ick>;
-		reg = <0x0a10>;
-		ti,bit-shift = <27>;
-	};
-
-	wdt2_fck: wdt2_fck@c00 {
-		#clock-cells = <0>;
-		compatible = "ti,wait-gate-clock";
-		clocks = <&wkup_32k_fck>;
-		reg = <0x0c00>;
-		ti,bit-shift = <5>;
-	};
-
-	wdt2_ick: wdt2_ick@c10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&wkup_l4_ick>;
-		reg = <0x0c10>;
-		ti,bit-shift = <5>;
-	};
-
-	wdt1_ick: wdt1_ick@c10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&wkup_l4_ick>;
-		reg = <0x0c10>;
-		ti,bit-shift = <4>;
-	};
-
-	gpio1_ick: gpio1_ick@c10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&wkup_l4_ick>;
-		reg = <0x0c10>;
-		ti,bit-shift = <3>;
-	};
-
-	omap_32ksync_ick: omap_32ksync_ick@c10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&wkup_l4_ick>;
-		reg = <0x0c10>;
-		ti,bit-shift = <2>;
-	};
-
-	gpt12_ick: gpt12_ick@c10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&wkup_l4_ick>;
-		reg = <0x0c10>;
-		ti,bit-shift = <1>;
-	};
-
-	gpt1_ick: gpt1_ick@c10 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&wkup_l4_ick>;
-		reg = <0x0c10>;
-		ti,bit-shift = <0>;
+	/* CM_ICLKEN_WKUP */
+	clock@c10 {
+		compatible = "ti,clksel";
+		reg = <0xc10>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
+
+		wdt2_ick: clock-wdt2-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "wdt2_ick";
+			clocks = <&wkup_l4_ick>;
+			ti,bit-shift = <5>;
+		};
+
+		wdt1_ick: clock-wdt1-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "wdt1_ick";
+			clocks = <&wkup_l4_ick>;
+			ti,bit-shift = <4>;
+		};
+
+		gpio1_ick: clock-gpio1-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "gpio1_ick";
+			clocks = <&wkup_l4_ick>;
+			ti,bit-shift = <3>;
+		};
+
+		omap_32ksync_ick: clock-omap-32ksync-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "omap_32ksync_ick";
+			clocks = <&wkup_l4_ick>;
+			ti,bit-shift = <2>;
+		};
+
+		gpt12_ick: clock-gpt12-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "gpt12_ick";
+			clocks = <&wkup_l4_ick>;
+			ti,bit-shift = <1>;
+		};
+
+		gpt1_ick: clock-gpt1-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "gpt1_ick";
+			clocks = <&wkup_l4_ick>;
+			ti,bit-shift = <0>;
+		};
 	};
 
 	per_96m_fck: per_96m_fck {
@@ -1090,27 +1249,227 @@
 		clock-div = <1>;
 	};
 
-	uart3_fck: uart3_fck@1000 {
-		#clock-cells = <0>;
-		compatible = "ti,wait-gate-clock";
-		clocks = <&per_48m_fck>;
-		reg = <0x1000>;
-		ti,bit-shift = <11>;
-	};
-
-	gpt2_gate_fck: gpt2_gate_fck@1000 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-gate-clock";
-		clocks = <&sys_ck>;
-		ti,bit-shift = <3>;
+	/* CM_FCLKEN_PER */
+	clock@1000 {
+		compatible = "ti,clksel";
 		reg = <0x1000>;
-	};
-
-	gpt2_mux_fck: gpt2_mux_fck@1040 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-mux-clock";
-		clocks = <&omap_32k_fck>, <&sys_ck>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
+
+		uart3_fck: clock-uart3-fck {
+			#clock-cells = <0>;
+			compatible = "ti,wait-gate-clock";
+			clock-output-names = "uart3_fck";
+			clocks = <&per_48m_fck>;
+			ti,bit-shift = <11>;
+		};
+
+		gpt2_gate_fck: clock-gpt2-gate-fck {
+			#clock-cells = <0>;
+			compatible = "ti,composite-gate-clock";
+			clock-output-names = "gpt2_gate_fck";
+			clocks = <&sys_ck>;
+			ti,bit-shift = <3>;
+		};
+
+		gpt3_gate_fck: clock-gpt3-gate-fck {
+			#clock-cells = <0>;
+			compatible = "ti,composite-gate-clock";
+			clock-output-names = "gpt3_gate_fck";
+			clocks = <&sys_ck>;
+			ti,bit-shift = <4>;
+		};
+
+		gpt4_gate_fck: clock-gpt4-gate-fck {
+			#clock-cells = <0>;
+			compatible = "ti,composite-gate-clock";
+			clock-output-names = "gpt4_gate_fck";
+			clocks = <&sys_ck>;
+			ti,bit-shift = <5>;
+		};
+
+		gpt5_gate_fck: clock-gpt5-gate-fck {
+			#clock-cells = <0>;
+			compatible = "ti,composite-gate-clock";
+			clock-output-names = "gpt5_gate_fck";
+			clocks = <&sys_ck>;
+			ti,bit-shift = <6>;
+		};
+
+		gpt6_gate_fck: clock-gpt6-gate-fck {
+			#clock-cells = <0>;
+			compatible = "ti,composite-gate-clock";
+			clock-output-names = "gpt6_gate_fck";
+			clocks = <&sys_ck>;
+			ti,bit-shift = <7>;
+		};
+
+		gpt7_gate_fck: clock-gpt7-gate-fck {
+			#clock-cells = <0>;
+			compatible = "ti,composite-gate-clock";
+			clock-output-names = "gpt7_gate_fck";
+			clocks = <&sys_ck>;
+			ti,bit-shift = <8>;
+		};
+
+		gpt8_gate_fck: clock-gpt8-gate-fck {
+			#clock-cells = <0>;
+			compatible = "ti,composite-gate-clock";
+			clock-output-names = "gpt8_gate_fck";
+			clocks = <&sys_ck>;
+			ti,bit-shift = <9>;
+		};
+
+		gpt9_gate_fck: clock-gpt9-gate-fck {
+			#clock-cells = <0>;
+			compatible = "ti,composite-gate-clock";
+			clock-output-names = "gpt9_gate_fck";
+			clocks = <&sys_ck>;
+			ti,bit-shift = <10>;
+		};
+
+		gpio6_dbck: clock-gpio6-dbck {
+			#clock-cells = <0>;
+			compatible = "ti,gate-clock";
+			clock-output-names = "gpio6_dbck";
+			clocks = <&per_32k_alwon_fck>;
+			ti,bit-shift = <17>;
+		};
+
+		gpio5_dbck: clock-gpio5-dbck {
+			#clock-cells = <0>;
+			compatible = "ti,gate-clock";
+			clock-output-names = "gpio5_dbck";
+			clocks = <&per_32k_alwon_fck>;
+			ti,bit-shift = <16>;
+		};
+
+		gpio4_dbck: clock-gpio4-dbck {
+			#clock-cells = <0>;
+			compatible = "ti,gate-clock";
+			clock-output-names = "gpio4_dbck";
+			clocks = <&per_32k_alwon_fck>;
+			ti,bit-shift = <15>;
+		};
+
+		gpio3_dbck: clock-gpio3-dbck {
+			#clock-cells = <0>;
+			compatible = "ti,gate-clock";
+			clock-output-names = "gpio3_dbck";
+			clocks = <&per_32k_alwon_fck>;
+			ti,bit-shift = <14>;
+		};
+
+		gpio2_dbck: clock-gpio2-dbck {
+			#clock-cells = <0>;
+			compatible = "ti,gate-clock";
+			clock-output-names = "gpio2_dbck";
+			clocks = <&per_32k_alwon_fck>;
+			ti,bit-shift = <13>;
+		};
+
+		wdt3_fck: clock-wdt3-fck {
+			#clock-cells = <0>;
+			compatible = "ti,wait-gate-clock";
+			clock-output-names = "wdt3_fck";
+			clocks = <&per_32k_alwon_fck>;
+			ti,bit-shift = <12>;
+		};
+
+		mcbsp2_gate_fck: clock-mcbsp2-gate-fck {
+			#clock-cells = <0>;
+			compatible = "ti,composite-gate-clock";
+			clock-output-names = "mcbsp2_gate_fck";
+			clocks = <&mcbsp_clks>;
+			ti,bit-shift = <0>;
+		};
+
+		mcbsp3_gate_fck: clock-mcbsp3-gate-fck {
+			#clock-cells = <0>;
+			compatible = "ti,composite-gate-clock";
+			clock-output-names = "mcbsp3_gate_fck";
+			clocks = <&mcbsp_clks>;
+			ti,bit-shift = <1>;
+		};
+
+		mcbsp4_gate_fck: clock-mcbsp4-gate-fck {
+			#clock-cells = <0>;
+			compatible = "ti,composite-gate-clock";
+			clock-output-names = "mcbsp4_gate_fck";
+			clocks = <&mcbsp_clks>;
+			ti,bit-shift = <2>;
+		};
+	};
+
+	/* CM_CLKSEL_PER */
+	clock@1040 {
+		compatible = "ti,clksel";
 		reg = <0x1040>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
+
+		gpt2_mux_fck: clock-gpt2-mux-fck {
+			#clock-cells = <0>;
+			compatible = "ti,composite-mux-clock";
+			clock-output-names = "gpt2_mux_fck";
+			clocks = <&omap_32k_fck>, <&sys_ck>;
+		};
+
+		gpt3_mux_fck: clock-gpt3-mux-fck {
+			#clock-cells = <0>;
+			compatible = "ti,composite-mux-clock";
+			clock-output-names = "gpt3_mux_fck";
+			clocks = <&omap_32k_fck>, <&sys_ck>;
+			ti,bit-shift = <1>;
+		};
+
+		gpt4_mux_fck: clock-gpt4-mux-fck {
+			#clock-cells = <0>;
+			compatible = "ti,composite-mux-clock";
+			clock-output-names = "gpt4_mux_fck";
+			clocks = <&omap_32k_fck>, <&sys_ck>;
+			ti,bit-shift = <2>;
+		};
+
+		gpt5_mux_fck: clock-gpt5-mux-fck {
+			#clock-cells = <0>;
+			compatible = "ti,composite-mux-clock";
+			clock-output-names = "gpt5_mux_fck";
+			clocks = <&omap_32k_fck>, <&sys_ck>;
+			ti,bit-shift = <3>;
+		};
+
+		gpt6_mux_fck: clock-gpt6-mux-fck {
+			#clock-cells = <0>;
+			compatible = "ti,composite-mux-clock";
+			clock-output-names = "gpt6_mux_fck";
+			clocks = <&omap_32k_fck>, <&sys_ck>;
+			ti,bit-shift = <4>;
+		};
+
+		gpt7_mux_fck: clock-gpt7-mux-fck {
+			#clock-cells = <0>;
+			compatible = "ti,composite-mux-clock";
+			clock-output-names = "gpt7_mux_fck";
+			clocks = <&omap_32k_fck>, <&sys_ck>;
+			ti,bit-shift = <5>;
+		};
+
+		gpt8_mux_fck: clock-gpt8-mux-fck {
+			#clock-cells = <0>;
+			compatible = "ti,composite-mux-clock";
+			clock-output-names = "gpt8_mux_fck";
+			clocks = <&omap_32k_fck>, <&sys_ck>;
+			ti,bit-shift = <6>;
+		};
+
+		gpt9_mux_fck: clock-gpt9-mux-fck {
+			#clock-cells = <0>;
+			compatible = "ti,composite-mux-clock";
+			clock-output-names = "gpt9_mux_fck";
+			clocks = <&omap_32k_fck>, <&sys_ck>;
+			ti,bit-shift = <7>;
+		};
 	};
 
 	gpt2_fck: gpt2_fck {
@@ -1119,154 +1478,42 @@
 		clocks = <&gpt2_gate_fck>, <&gpt2_mux_fck>;
 	};
 
-	gpt3_gate_fck: gpt3_gate_fck@1000 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-gate-clock";
-		clocks = <&sys_ck>;
-		ti,bit-shift = <4>;
-		reg = <0x1000>;
-	};
-
-	gpt3_mux_fck: gpt3_mux_fck@1040 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-mux-clock";
-		clocks = <&omap_32k_fck>, <&sys_ck>;
-		ti,bit-shift = <1>;
-		reg = <0x1040>;
-	};
-
 	gpt3_fck: gpt3_fck {
 		#clock-cells = <0>;
 		compatible = "ti,composite-clock";
 		clocks = <&gpt3_gate_fck>, <&gpt3_mux_fck>;
 	};
 
-	gpt4_gate_fck: gpt4_gate_fck@1000 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-gate-clock";
-		clocks = <&sys_ck>;
-		ti,bit-shift = <5>;
-		reg = <0x1000>;
-	};
-
-	gpt4_mux_fck: gpt4_mux_fck@1040 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-mux-clock";
-		clocks = <&omap_32k_fck>, <&sys_ck>;
-		ti,bit-shift = <2>;
-		reg = <0x1040>;
-	};
-
 	gpt4_fck: gpt4_fck {
 		#clock-cells = <0>;
 		compatible = "ti,composite-clock";
 		clocks = <&gpt4_gate_fck>, <&gpt4_mux_fck>;
 	};
 
-	gpt5_gate_fck: gpt5_gate_fck@1000 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-gate-clock";
-		clocks = <&sys_ck>;
-		ti,bit-shift = <6>;
-		reg = <0x1000>;
-	};
-
-	gpt5_mux_fck: gpt5_mux_fck@1040 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-mux-clock";
-		clocks = <&omap_32k_fck>, <&sys_ck>;
-		ti,bit-shift = <3>;
-		reg = <0x1040>;
-	};
-
 	gpt5_fck: gpt5_fck {
 		#clock-cells = <0>;
 		compatible = "ti,composite-clock";
 		clocks = <&gpt5_gate_fck>, <&gpt5_mux_fck>;
 	};
 
-	gpt6_gate_fck: gpt6_gate_fck@1000 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-gate-clock";
-		clocks = <&sys_ck>;
-		ti,bit-shift = <7>;
-		reg = <0x1000>;
-	};
-
-	gpt6_mux_fck: gpt6_mux_fck@1040 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-mux-clock";
-		clocks = <&omap_32k_fck>, <&sys_ck>;
-		ti,bit-shift = <4>;
-		reg = <0x1040>;
-	};
-
 	gpt6_fck: gpt6_fck {
 		#clock-cells = <0>;
 		compatible = "ti,composite-clock";
 		clocks = <&gpt6_gate_fck>, <&gpt6_mux_fck>;
 	};
 
-	gpt7_gate_fck: gpt7_gate_fck@1000 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-gate-clock";
-		clocks = <&sys_ck>;
-		ti,bit-shift = <8>;
-		reg = <0x1000>;
-	};
-
-	gpt7_mux_fck: gpt7_mux_fck@1040 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-mux-clock";
-		clocks = <&omap_32k_fck>, <&sys_ck>;
-		ti,bit-shift = <5>;
-		reg = <0x1040>;
-	};
-
 	gpt7_fck: gpt7_fck {
 		#clock-cells = <0>;
 		compatible = "ti,composite-clock";
 		clocks = <&gpt7_gate_fck>, <&gpt7_mux_fck>;
 	};
 
-	gpt8_gate_fck: gpt8_gate_fck@1000 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-gate-clock";
-		clocks = <&sys_ck>;
-		ti,bit-shift = <9>;
-		reg = <0x1000>;
-	};
-
-	gpt8_mux_fck: gpt8_mux_fck@1040 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-mux-clock";
-		clocks = <&omap_32k_fck>, <&sys_ck>;
-		ti,bit-shift = <6>;
-		reg = <0x1040>;
-	};
-
 	gpt8_fck: gpt8_fck {
 		#clock-cells = <0>;
 		compatible = "ti,composite-clock";
 		clocks = <&gpt8_gate_fck>, <&gpt8_mux_fck>;
 	};
 
-	gpt9_gate_fck: gpt9_gate_fck@1000 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-gate-clock";
-		clocks = <&sys_ck>;
-		ti,bit-shift = <10>;
-		reg = <0x1000>;
-	};
-
-	gpt9_mux_fck: gpt9_mux_fck@1040 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-mux-clock";
-		clocks = <&omap_32k_fck>, <&sys_ck>;
-		ti,bit-shift = <7>;
-		reg = <0x1040>;
-	};
-
 	gpt9_fck: gpt9_fck {
 		#clock-cells = <0>;
 		compatible = "ti,composite-clock";
@@ -1281,54 +1528,6 @@
 		clock-div = <1>;
 	};
 
-	gpio6_dbck: gpio6_dbck@1000 {
-		#clock-cells = <0>;
-		compatible = "ti,gate-clock";
-		clocks = <&per_32k_alwon_fck>;
-		reg = <0x1000>;
-		ti,bit-shift = <17>;
-	};
-
-	gpio5_dbck: gpio5_dbck@1000 {
-		#clock-cells = <0>;
-		compatible = "ti,gate-clock";
-		clocks = <&per_32k_alwon_fck>;
-		reg = <0x1000>;
-		ti,bit-shift = <16>;
-	};
-
-	gpio4_dbck: gpio4_dbck@1000 {
-		#clock-cells = <0>;
-		compatible = "ti,gate-clock";
-		clocks = <&per_32k_alwon_fck>;
-		reg = <0x1000>;
-		ti,bit-shift = <15>;
-	};
-
-	gpio3_dbck: gpio3_dbck@1000 {
-		#clock-cells = <0>;
-		compatible = "ti,gate-clock";
-		clocks = <&per_32k_alwon_fck>;
-		reg = <0x1000>;
-		ti,bit-shift = <14>;
-	};
-
-	gpio2_dbck: gpio2_dbck@1000 {
-		#clock-cells = <0>;
-		compatible = "ti,gate-clock";
-		clocks = <&per_32k_alwon_fck>;
-		reg = <0x1000>;
-		ti,bit-shift = <13>;
-	};
-
-	wdt3_fck: wdt3_fck@1000 {
-		#clock-cells = <0>;
-		compatible = "ti,wait-gate-clock";
-		clocks = <&per_32k_alwon_fck>;
-		reg = <0x1000>;
-		ti,bit-shift = <12>;
-	};
-
 	per_l4_ick: per_l4_ick {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
@@ -1337,187 +1536,164 @@
 		clock-div = <1>;
 	};
 
-	gpio6_ick: gpio6_ick@1010 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&per_l4_ick>;
-		reg = <0x1010>;
-		ti,bit-shift = <17>;
-	};
-
-	gpio5_ick: gpio5_ick@1010 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&per_l4_ick>;
-		reg = <0x1010>;
-		ti,bit-shift = <16>;
-	};
-
-	gpio4_ick: gpio4_ick@1010 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&per_l4_ick>;
-		reg = <0x1010>;
-		ti,bit-shift = <15>;
-	};
-
-	gpio3_ick: gpio3_ick@1010 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&per_l4_ick>;
-		reg = <0x1010>;
-		ti,bit-shift = <14>;
-	};
-
-	gpio2_ick: gpio2_ick@1010 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&per_l4_ick>;
-		reg = <0x1010>;
-		ti,bit-shift = <13>;
-	};
-
-	wdt3_ick: wdt3_ick@1010 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&per_l4_ick>;
-		reg = <0x1010>;
-		ti,bit-shift = <12>;
-	};
-
-	uart3_ick: uart3_ick@1010 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&per_l4_ick>;
-		reg = <0x1010>;
-		ti,bit-shift = <11>;
-	};
-
-	uart4_ick: uart4_ick@1010 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&per_l4_ick>;
-		reg = <0x1010>;
-		ti,bit-shift = <18>;
-	};
-
-	gpt9_ick: gpt9_ick@1010 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&per_l4_ick>;
-		reg = <0x1010>;
-		ti,bit-shift = <10>;
-	};
-
-	gpt8_ick: gpt8_ick@1010 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&per_l4_ick>;
-		reg = <0x1010>;
-		ti,bit-shift = <9>;
-	};
-
-	gpt7_ick: gpt7_ick@1010 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&per_l4_ick>;
-		reg = <0x1010>;
-		ti,bit-shift = <8>;
-	};
-
-	gpt6_ick: gpt6_ick@1010 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&per_l4_ick>;
-		reg = <0x1010>;
-		ti,bit-shift = <7>;
-	};
-
-	gpt5_ick: gpt5_ick@1010 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&per_l4_ick>;
-		reg = <0x1010>;
-		ti,bit-shift = <6>;
-	};
-
-	gpt4_ick: gpt4_ick@1010 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&per_l4_ick>;
-		reg = <0x1010>;
-		ti,bit-shift = <5>;
-	};
-
-	gpt3_ick: gpt3_ick@1010 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&per_l4_ick>;
-		reg = <0x1010>;
-		ti,bit-shift = <4>;
-	};
-
-	gpt2_ick: gpt2_ick@1010 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&per_l4_ick>;
-		reg = <0x1010>;
-		ti,bit-shift = <3>;
-	};
-
-	mcbsp2_ick: mcbsp2_ick@1010 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&per_l4_ick>;
-		reg = <0x1010>;
-		ti,bit-shift = <0>;
-	};
-
-	mcbsp3_ick: mcbsp3_ick@1010 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&per_l4_ick>;
-		reg = <0x1010>;
-		ti,bit-shift = <1>;
-	};
-
-	mcbsp4_ick: mcbsp4_ick@1010 {
-		#clock-cells = <0>;
-		compatible = "ti,omap3-interface-clock";
-		clocks = <&per_l4_ick>;
+	/* CM_ICLKEN_PER */
+	clock@1010 {
+		compatible = "ti,clksel";
 		reg = <0x1010>;
-		ti,bit-shift = <2>;
-	};
-
-	mcbsp2_gate_fck: mcbsp2_gate_fck@1000 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-gate-clock";
-		clocks = <&mcbsp_clks>;
-		ti,bit-shift = <0>;
-		reg = <0x1000>;
-	};
-
-	mcbsp3_gate_fck: mcbsp3_gate_fck@1000 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-gate-clock";
-		clocks = <&mcbsp_clks>;
-		ti,bit-shift = <1>;
-		reg = <0x1000>;
-	};
-
-	mcbsp4_gate_fck: mcbsp4_gate_fck@1000 {
-		#clock-cells = <0>;
-		compatible = "ti,composite-gate-clock";
-		clocks = <&mcbsp_clks>;
-		ti,bit-shift = <2>;
-		reg = <0x1000>;
-	};
-
-	emu_src_mux_ck: emu_src_mux_ck@1140 {
-		#clock-cells = <0>;
-		compatible = "ti,mux-clock";
-		clocks = <&sys_ck>, <&emu_core_alwon_ck>, <&emu_per_alwon_ck>, <&emu_mpu_alwon_ck>;
-		reg = <0x1140>;
+		#clock-cells = <2>;
+		#address-cells = <0>;
+
+		gpio6_ick: clock-gpio6-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "gpio6_ick";
+			clocks = <&per_l4_ick>;
+			ti,bit-shift = <17>;
+		};
+
+		gpio5_ick: clock-gpio5-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "gpio5_ick";
+			clocks = <&per_l4_ick>;
+			ti,bit-shift = <16>;
+		};
+
+		gpio4_ick: clock-gpio4-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "gpio4_ick";
+			clocks = <&per_l4_ick>;
+			ti,bit-shift = <15>;
+		};
+
+		gpio3_ick: clock-gpio3-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "gpio3_ick";
+			clocks = <&per_l4_ick>;
+			ti,bit-shift = <14>;
+		};
+
+		gpio2_ick: clock-gpio2-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "gpio2_ick";
+			clocks = <&per_l4_ick>;
+			ti,bit-shift = <13>;
+		};
+
+		wdt3_ick: clock-wdt3-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "wdt3_ick";
+			clocks = <&per_l4_ick>;
+			ti,bit-shift = <12>;
+		};
+
+		uart3_ick: clock-uart3-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "uart3_ick";
+			clocks = <&per_l4_ick>;
+			ti,bit-shift = <11>;
+		};
+
+		uart4_ick: clock-uart4-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "uart4_ick";
+			clocks = <&per_l4_ick>;
+			ti,bit-shift = <18>;
+		};
+
+		gpt9_ick: clock-gpt9-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "gpt9_ick";
+			clocks = <&per_l4_ick>;
+			ti,bit-shift = <10>;
+		};
+
+		gpt8_ick: clock-gpt8-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "gpt8_ick";
+			clocks = <&per_l4_ick>;
+			ti,bit-shift = <9>;
+		};
+
+		gpt7_ick: clock-gpt7-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "gpt7_ick";
+			clocks = <&per_l4_ick>;
+			ti,bit-shift = <8>;
+		};
+
+		gpt6_ick: clock-gpt6-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "gpt6_ick";
+			clocks = <&per_l4_ick>;
+			ti,bit-shift = <7>;
+		};
+
+		gpt5_ick: clock-gpt5-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "gpt5_ick";
+			clocks = <&per_l4_ick>;
+			ti,bit-shift = <6>;
+		};
+
+		gpt4_ick: clock-gpt4-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "gpt4_ick";
+			clocks = <&per_l4_ick>;
+			ti,bit-shift = <5>;
+		};
+
+		gpt3_ick: clock-gpt3-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "gpt3_ick";
+			clocks = <&per_l4_ick>;
+			ti,bit-shift = <4>;
+		};
+
+		gpt2_ick: clock-gpt2-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "gpt2_ick";
+			clocks = <&per_l4_ick>;
+			ti,bit-shift = <3>;
+		};
+
+		mcbsp2_ick: clock-mcbsp2-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "mcbsp2_ick";
+			clocks = <&per_l4_ick>;
+			ti,bit-shift = <0>;
+		};
+
+		mcbsp3_ick: clock-mcbsp3-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "mcbsp3_ick";
+			clocks = <&per_l4_ick>;
+			ti,bit-shift = <1>;
+		};
+
+		mcbsp4_ick: clock-mcbsp4-ick {
+			#clock-cells = <0>;
+			compatible = "ti,omap3-interface-clock";
+			clock-output-names = "mcbsp4_ick";
+			clocks = <&per_l4_ick>;
+			ti,bit-shift = <2>;
+		};
 	};
 
 	emu_src_ck: emu_src_ck {
@@ -1526,54 +1702,6 @@
 		clocks = <&emu_src_mux_ck>;
 	};
 
-	pclk_fck: pclk_fck@1140 {
-		#clock-cells = <0>;
-		compatible = "ti,divider-clock";
-		clocks = <&emu_src_ck>;
-		ti,bit-shift = <8>;
-		ti,max-div = <7>;
-		reg = <0x1140>;
-		ti,index-starts-at-one;
-	};
-
-	pclkx2_fck: pclkx2_fck@1140 {
-		#clock-cells = <0>;
-		compatible = "ti,divider-clock";
-		clocks = <&emu_src_ck>;
-		ti,bit-shift = <6>;
-		ti,max-div = <3>;
-		reg = <0x1140>;
-		ti,index-starts-at-one;
-	};
-
-	atclk_fck: atclk_fck@1140 {
-		#clock-cells = <0>;
-		compatible = "ti,divider-clock";
-		clocks = <&emu_src_ck>;
-		ti,bit-shift = <4>;
-		ti,max-div = <3>;
-		reg = <0x1140>;
-		ti,index-starts-at-one;
-	};
-
-	traceclk_src_fck: traceclk_src_fck@1140 {
-		#clock-cells = <0>;
-		compatible = "ti,mux-clock";
-		clocks = <&sys_ck>, <&emu_core_alwon_ck>, <&emu_per_alwon_ck>, <&emu_mpu_alwon_ck>;
-		ti,bit-shift = <2>;
-		reg = <0x1140>;
-	};
-
-	traceclk_fck: traceclk_fck@1140 {
-		#clock-cells = <0>;
-		compatible = "ti,divider-clock";
-		clocks = <&traceclk_src_fck>;
-		ti,bit-shift = <11>;
-		ti,max-div = <7>;
-		reg = <0x1140>;
-		ti,index-starts-at-one;
-	};
-
 	secure_32k_fck: secure_32k_fck {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
diff --git a/arch/arm/boot/dts/omap4-cpu-thermal.dtsi b/arch/arm/boot/dts/omap4-cpu-thermal.dtsi
index 03d054b2bf9a..4d7eeb133dad 100644
--- a/arch/arm/boot/dts/omap4-cpu-thermal.dtsi
+++ b/arch/arm/boot/dts/omap4-cpu-thermal.dtsi
@@ -1,12 +1,9 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Device Tree Source for OMAP4/5 SoC CPU thermal
  *
  * Copyright (C) 2013 Texas Instruments Incorporated - https://www.ti.com/
  * Contact: Eduardo Valentin <eduardo.valentin@ti.com>
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2.  This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
  */
 
 #include <dt-bindings/thermal/thermal.h>
diff --git a/arch/arm/boot/dts/omap4-panda-common.dtsi b/arch/arm/boot/dts/omap4-panda-common.dtsi
index 609a8dea946b..518652a599bd 100644
--- a/arch/arm/boot/dts/omap4-panda-common.dtsi
+++ b/arch/arm/boot/dts/omap4-panda-common.dtsi
@@ -558,7 +558,7 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		ethernet: usbether@1 {
+		ethernet: ethernet@1 {
 			compatible = "usb424,ec00";
 			reg = <1>;
 		};
diff --git a/arch/arm/boot/dts/omap443x-clocks.dtsi b/arch/arm/boot/dts/omap443x-clocks.dtsi
index 39297868ec85..581e088231b5 100644
--- a/arch/arm/boot/dts/omap443x-clocks.dtsi
+++ b/arch/arm/boot/dts/omap443x-clocks.dtsi
@@ -8,6 +8,7 @@
 	bandgap_fclk: bandgap_fclk@1888 {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
+		clock-output-names = "bandgap_fclk";
 		clocks = <&sys_32k_ck>;
 		ti,bit-shift = <8>;
 		reg = <0x1888>;
diff --git a/arch/arm/boot/dts/omap443x.dtsi b/arch/arm/boot/dts/omap443x.dtsi
index 8466161197ae..238aceb799f8 100644
--- a/arch/arm/boot/dts/omap443x.dtsi
+++ b/arch/arm/boot/dts/omap443x.dtsi
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Device Tree Source for OMAP443x SoC
  *
  * Copyright (C) 2013 Texas Instruments Incorporated - https://www.ti.com/
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2.  This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
  */
 
 #include "omap4.dtsi"
diff --git a/arch/arm/boot/dts/omap4460.dtsi b/arch/arm/boot/dts/omap4460.dtsi
index 3d6db1db94e0..1b27a862ae81 100644
--- a/arch/arm/boot/dts/omap4460.dtsi
+++ b/arch/arm/boot/dts/omap4460.dtsi
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Device Tree Source for OMAP4460 SoC
  *
  * Copyright (C) 2012 Texas Instruments Incorporated - https://www.ti.com/
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2.  This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
  */
 #include "omap4.dtsi"
 
diff --git a/arch/arm/boot/dts/omap446x-clocks.dtsi b/arch/arm/boot/dts/omap446x-clocks.dtsi
index 0f41714cffbb..d9362fef6720 100644
--- a/arch/arm/boot/dts/omap446x-clocks.dtsi
+++ b/arch/arm/boot/dts/omap446x-clocks.dtsi
@@ -8,6 +8,7 @@
 	div_ts_ck: div_ts_ck@1888 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "div_ts_ck";
 		clocks = <&l4_wkup_clk_mux_ck>;
 		ti,bit-shift = <24>;
 		reg = <0x1888>;
@@ -17,6 +18,7 @@
 	bandgap_ts_fclk: bandgap_ts_fclk@1888 {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
+		clock-output-names = "bandgap_ts_fclk";
 		clocks = <&div_ts_ck>;
 		ti,bit-shift = <8>;
 		reg = <0x1888>;
diff --git a/arch/arm/boot/dts/omap44xx-clocks.dtsi b/arch/arm/boot/dts/omap44xx-clocks.dtsi
index 1f1c04d8f472..8df73d285638 100644
--- a/arch/arm/boot/dts/omap44xx-clocks.dtsi
+++ b/arch/arm/boot/dts/omap44xx-clocks.dtsi
@@ -8,18 +8,21 @@
 	extalt_clkin_ck: extalt_clkin_ck {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "extalt_clkin_ck";
 		clock-frequency = <59000000>;
 	};
 
 	pad_clks_src_ck: pad_clks_src_ck {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "pad_clks_src_ck";
 		clock-frequency = <12000000>;
 	};
 
 	pad_clks_ck: pad_clks_ck@108 {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
+		clock-output-names = "pad_clks_ck";
 		clocks = <&pad_clks_src_ck>;
 		ti,bit-shift = <8>;
 		reg = <0x0108>;
@@ -28,24 +31,28 @@
 	pad_slimbus_core_clks_ck: pad_slimbus_core_clks_ck {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "pad_slimbus_core_clks_ck";
 		clock-frequency = <12000000>;
 	};
 
 	secure_32k_clk_src_ck: secure_32k_clk_src_ck {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "secure_32k_clk_src_ck";
 		clock-frequency = <32768>;
 	};
 
 	slimbus_src_clk: slimbus_src_clk {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "slimbus_src_clk";
 		clock-frequency = <12000000>;
 	};
 
 	slimbus_clk: slimbus_clk@108 {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
+		clock-output-names = "slimbus_clk";
 		clocks = <&slimbus_src_clk>;
 		ti,bit-shift = <10>;
 		reg = <0x0108>;
@@ -54,84 +61,98 @@
 	sys_32k_ck: sys_32k_ck {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "sys_32k_ck";
 		clock-frequency = <32768>;
 	};
 
 	virt_12000000_ck: virt_12000000_ck {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "virt_12000000_ck";
 		clock-frequency = <12000000>;
 	};
 
 	virt_13000000_ck: virt_13000000_ck {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "virt_13000000_ck";
 		clock-frequency = <13000000>;
 	};
 
 	virt_16800000_ck: virt_16800000_ck {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "virt_16800000_ck";
 		clock-frequency = <16800000>;
 	};
 
 	virt_19200000_ck: virt_19200000_ck {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "virt_19200000_ck";
 		clock-frequency = <19200000>;
 	};
 
 	virt_26000000_ck: virt_26000000_ck {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "virt_26000000_ck";
 		clock-frequency = <26000000>;
 	};
 
 	virt_27000000_ck: virt_27000000_ck {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "virt_27000000_ck";
 		clock-frequency = <27000000>;
 	};
 
 	virt_38400000_ck: virt_38400000_ck {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "virt_38400000_ck";
 		clock-frequency = <38400000>;
 	};
 
 	tie_low_clock_ck: tie_low_clock_ck {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "tie_low_clock_ck";
 		clock-frequency = <0>;
 	};
 
 	utmi_phy_clkout_ck: utmi_phy_clkout_ck {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "utmi_phy_clkout_ck";
 		clock-frequency = <60000000>;
 	};
 
 	xclk60mhsp1_ck: xclk60mhsp1_ck {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "xclk60mhsp1_ck";
 		clock-frequency = <60000000>;
 	};
 
 	xclk60mhsp2_ck: xclk60mhsp2_ck {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "xclk60mhsp2_ck";
 		clock-frequency = <60000000>;
 	};
 
 	xclk60motg_ck: xclk60motg_ck {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "xclk60motg_ck";
 		clock-frequency = <60000000>;
 	};
 
 	dpll_abe_ck: dpll_abe_ck@1e0 {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-m4xen-clock";
+		clock-output-names = "dpll_abe_ck";
 		clocks = <&abe_dpll_refclk_mux_ck>, <&abe_dpll_bypass_clk_mux_ck>;
 		reg = <0x01e0>, <0x01e4>, <0x01ec>, <0x01e8>;
 	};
@@ -139,6 +160,7 @@
 	dpll_abe_x2_ck: dpll_abe_x2_ck@1f0 {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-x2-clock";
+		clock-output-names = "dpll_abe_x2_ck";
 		clocks = <&dpll_abe_ck>;
 		reg = <0x01f0>;
 	};
@@ -146,6 +168,7 @@
 	dpll_abe_m2x2_ck: dpll_abe_m2x2_ck@1f0 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_abe_m2x2_ck";
 		clocks = <&dpll_abe_x2_ck>;
 		ti,max-div = <31>;
 		ti,autoidle-shift = <8>;
@@ -157,6 +180,7 @@
 	abe_24m_fclk: abe_24m_fclk {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "abe_24m_fclk";
 		clocks = <&dpll_abe_m2x2_ck>;
 		clock-mult = <1>;
 		clock-div = <8>;
@@ -165,6 +189,7 @@
 	abe_clk: abe_clk@108 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "abe_clk";
 		clocks = <&dpll_abe_m2x2_ck>;
 		ti,max-div = <4>;
 		reg = <0x0108>;
@@ -175,6 +200,7 @@
 	dpll_abe_m3x2_ck: dpll_abe_m3x2_ck@1f4 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_abe_m3x2_ck";
 		clocks = <&dpll_abe_x2_ck>;
 		ti,max-div = <31>;
 		ti,autoidle-shift = <8>;
@@ -186,6 +212,7 @@
 	core_hsd_byp_clk_mux_ck: core_hsd_byp_clk_mux_ck@12c {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "core_hsd_byp_clk_mux_ck";
 		clocks = <&sys_clkin_ck>, <&dpll_abe_m3x2_ck>;
 		ti,bit-shift = <23>;
 		reg = <0x012c>;
@@ -194,6 +221,7 @@
 	dpll_core_ck: dpll_core_ck@120 {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-core-clock";
+		clock-output-names = "dpll_core_ck";
 		clocks = <&sys_clkin_ck>, <&core_hsd_byp_clk_mux_ck>;
 		reg = <0x0120>, <0x0124>, <0x012c>, <0x0128>;
 	};
@@ -201,12 +229,14 @@
 	dpll_core_x2_ck: dpll_core_x2_ck {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-x2-clock";
+		clock-output-names = "dpll_core_x2_ck";
 		clocks = <&dpll_core_ck>;
 	};
 
 	dpll_core_m6x2_ck: dpll_core_m6x2_ck@140 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_core_m6x2_ck";
 		clocks = <&dpll_core_x2_ck>;
 		ti,max-div = <31>;
 		ti,autoidle-shift = <8>;
@@ -218,6 +248,7 @@
 	dpll_core_m2_ck: dpll_core_m2_ck@130 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_core_m2_ck";
 		clocks = <&dpll_core_ck>;
 		ti,max-div = <31>;
 		ti,autoidle-shift = <8>;
@@ -229,6 +260,7 @@
 	ddrphy_ck: ddrphy_ck {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "ddrphy_ck";
 		clocks = <&dpll_core_m2_ck>;
 		clock-mult = <1>;
 		clock-div = <2>;
@@ -237,6 +269,7 @@
 	dpll_core_m5x2_ck: dpll_core_m5x2_ck@13c {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_core_m5x2_ck";
 		clocks = <&dpll_core_x2_ck>;
 		ti,max-div = <31>;
 		ti,autoidle-shift = <8>;
@@ -248,6 +281,7 @@
 	div_core_ck: div_core_ck@100 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "div_core_ck";
 		clocks = <&dpll_core_m5x2_ck>;
 		reg = <0x0100>;
 		ti,max-div = <2>;
@@ -256,6 +290,7 @@
 	div_iva_hs_clk: div_iva_hs_clk@1dc {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "div_iva_hs_clk";
 		clocks = <&dpll_core_m5x2_ck>;
 		ti,max-div = <4>;
 		reg = <0x01dc>;
@@ -265,6 +300,7 @@
 	div_mpu_hs_clk: div_mpu_hs_clk@19c {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "div_mpu_hs_clk";
 		clocks = <&dpll_core_m5x2_ck>;
 		ti,max-div = <4>;
 		reg = <0x019c>;
@@ -274,6 +310,7 @@
 	dpll_core_m4x2_ck: dpll_core_m4x2_ck@138 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_core_m4x2_ck";
 		clocks = <&dpll_core_x2_ck>;
 		ti,max-div = <31>;
 		ti,autoidle-shift = <8>;
@@ -285,6 +322,7 @@
 	dll_clk_div_ck: dll_clk_div_ck {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "dll_clk_div_ck";
 		clocks = <&dpll_core_m4x2_ck>;
 		clock-mult = <1>;
 		clock-div = <2>;
@@ -293,6 +331,7 @@
 	dpll_abe_m2_ck: dpll_abe_m2_ck@1f0 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_abe_m2_ck";
 		clocks = <&dpll_abe_ck>;
 		ti,max-div = <31>;
 		reg = <0x01f0>;
@@ -302,6 +341,7 @@
 	dpll_core_m3x2_gate_ck: dpll_core_m3x2_gate_ck@134 {
 		#clock-cells = <0>;
 		compatible = "ti,composite-no-wait-gate-clock";
+		clock-output-names = "dpll_core_m3x2_gate_ck";
 		clocks = <&dpll_core_x2_ck>;
 		ti,bit-shift = <8>;
 		reg = <0x0134>;
@@ -310,6 +350,7 @@
 	dpll_core_m3x2_div_ck: dpll_core_m3x2_div_ck@134 {
 		#clock-cells = <0>;
 		compatible = "ti,composite-divider-clock";
+		clock-output-names = "dpll_core_m3x2_div_ck";
 		clocks = <&dpll_core_x2_ck>;
 		ti,max-div = <31>;
 		reg = <0x0134>;
@@ -319,12 +360,14 @@
 	dpll_core_m3x2_ck: dpll_core_m3x2_ck {
 		#clock-cells = <0>;
 		compatible = "ti,composite-clock";
+		clock-output-names = "dpll_core_m3x2_ck";
 		clocks = <&dpll_core_m3x2_gate_ck>, <&dpll_core_m3x2_div_ck>;
 	};
 
 	dpll_core_m7x2_ck: dpll_core_m7x2_ck@144 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_core_m7x2_ck";
 		clocks = <&dpll_core_x2_ck>;
 		ti,max-div = <31>;
 		ti,autoidle-shift = <8>;
@@ -336,6 +379,7 @@
 	iva_hsd_byp_clk_mux_ck: iva_hsd_byp_clk_mux_ck@1ac {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "iva_hsd_byp_clk_mux_ck";
 		clocks = <&sys_clkin_ck>, <&div_iva_hs_clk>;
 		ti,bit-shift = <23>;
 		reg = <0x01ac>;
@@ -344,6 +388,7 @@
 	dpll_iva_ck: dpll_iva_ck@1a0 {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-clock";
+		clock-output-names = "dpll_iva_ck";
 		clocks = <&sys_clkin_ck>, <&iva_hsd_byp_clk_mux_ck>;
 		reg = <0x01a0>, <0x01a4>, <0x01ac>, <0x01a8>;
 		assigned-clocks = <&dpll_iva_ck>;
@@ -353,12 +398,14 @@
 	dpll_iva_x2_ck: dpll_iva_x2_ck {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-x2-clock";
+		clock-output-names = "dpll_iva_x2_ck";
 		clocks = <&dpll_iva_ck>;
 	};
 
 	dpll_iva_m4x2_ck: dpll_iva_m4x2_ck@1b8 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_iva_m4x2_ck";
 		clocks = <&dpll_iva_x2_ck>;
 		ti,max-div = <31>;
 		ti,autoidle-shift = <8>;
@@ -372,6 +419,7 @@
 	dpll_iva_m5x2_ck: dpll_iva_m5x2_ck@1bc {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_iva_m5x2_ck";
 		clocks = <&dpll_iva_x2_ck>;
 		ti,max-div = <31>;
 		ti,autoidle-shift = <8>;
@@ -385,6 +433,7 @@
 	dpll_mpu_ck: dpll_mpu_ck@160 {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-clock";
+		clock-output-names = "dpll_mpu_ck";
 		clocks = <&sys_clkin_ck>, <&div_mpu_hs_clk>;
 		reg = <0x0160>, <0x0164>, <0x016c>, <0x0168>;
 	};
@@ -392,6 +441,7 @@
 	dpll_mpu_m2_ck: dpll_mpu_m2_ck@170 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_mpu_m2_ck";
 		clocks = <&dpll_mpu_ck>;
 		ti,max-div = <31>;
 		ti,autoidle-shift = <8>;
@@ -403,6 +453,7 @@
 	per_hs_clk_div_ck: per_hs_clk_div_ck {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "per_hs_clk_div_ck";
 		clocks = <&dpll_abe_m3x2_ck>;
 		clock-mult = <1>;
 		clock-div = <2>;
@@ -411,6 +462,7 @@
 	usb_hs_clk_div_ck: usb_hs_clk_div_ck {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "usb_hs_clk_div_ck";
 		clocks = <&dpll_abe_m3x2_ck>;
 		clock-mult = <1>;
 		clock-div = <3>;
@@ -419,6 +471,7 @@
 	l3_div_ck: l3_div_ck@100 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "l3_div_ck";
 		clocks = <&div_core_ck>;
 		ti,bit-shift = <4>;
 		ti,max-div = <2>;
@@ -428,6 +481,7 @@
 	l4_div_ck: l4_div_ck@100 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "l4_div_ck";
 		clocks = <&l3_div_ck>;
 		ti,bit-shift = <8>;
 		ti,max-div = <2>;
@@ -437,6 +491,7 @@
 	lp_clk_div_ck: lp_clk_div_ck {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "lp_clk_div_ck";
 		clocks = <&dpll_abe_m2x2_ck>;
 		clock-mult = <1>;
 		clock-div = <16>;
@@ -445,6 +500,7 @@
 	mpu_periphclk: mpu_periphclk {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "mpu_periphclk";
 		clocks = <&dpll_mpu_ck>;
 		clock-mult = <1>;
 		clock-div = <2>;
@@ -453,6 +509,7 @@
 	ocp_abe_iclk: ocp_abe_iclk@528 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "ocp_abe_iclk";
 		clocks = <&abe_clkctrl OMAP4_AESS_CLKCTRL 24>;
 		ti,bit-shift = <24>;
 		reg = <0x0528>;
@@ -462,6 +519,7 @@
 	per_abe_24m_fclk: per_abe_24m_fclk {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "per_abe_24m_fclk";
 		clocks = <&dpll_abe_m2_ck>;
 		clock-mult = <1>;
 		clock-div = <4>;
@@ -470,6 +528,7 @@
 	dummy_ck: dummy_ck {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "dummy_ck";
 		clock-frequency = <0>;
 	};
 };
@@ -478,6 +537,7 @@
 	sys_clkin_ck: sys_clkin_ck@110 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "sys_clkin_ck";
 		clocks = <&virt_12000000_ck>, <&virt_13000000_ck>, <&virt_16800000_ck>, <&virt_19200000_ck>, <&virt_26000000_ck>, <&virt_27000000_ck>, <&virt_38400000_ck>;
 		reg = <0x0110>;
 		ti,index-starts-at-one;
@@ -486,6 +546,7 @@
 	abe_dpll_bypass_clk_mux_ck: abe_dpll_bypass_clk_mux_ck@108 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "abe_dpll_bypass_clk_mux_ck";
 		clocks = <&sys_clkin_ck>, <&sys_32k_ck>;
 		ti,bit-shift = <24>;
 		reg = <0x0108>;
@@ -494,6 +555,7 @@
 	abe_dpll_refclk_mux_ck: abe_dpll_refclk_mux_ck@10c {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "abe_dpll_refclk_mux_ck";
 		clocks = <&sys_clkin_ck>, <&sys_32k_ck>;
 		reg = <0x010c>;
 	};
@@ -501,6 +563,7 @@
 	dbgclk_mux_ck: dbgclk_mux_ck {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "dbgclk_mux_ck";
 		clocks = <&sys_clkin_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
@@ -509,6 +572,7 @@
 	l4_wkup_clk_mux_ck: l4_wkup_clk_mux_ck@108 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "l4_wkup_clk_mux_ck";
 		clocks = <&sys_clkin_ck>, <&lp_clk_div_ck>;
 		reg = <0x0108>;
 	};
@@ -516,6 +580,7 @@
 	syc_clk_div_ck: syc_clk_div_ck@100 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "syc_clk_div_ck";
 		clocks = <&sys_clkin_ck>;
 		reg = <0x0100>;
 		ti,max-div = <2>;
@@ -524,6 +589,7 @@
 	usim_ck: usim_ck@1858 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "usim_ck";
 		clocks = <&dpll_per_m4x2_ck>;
 		ti,bit-shift = <24>;
 		reg = <0x1858>;
@@ -533,6 +599,7 @@
 	usim_fclk: usim_fclk@1858 {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
+		clock-output-names = "usim_fclk";
 		clocks = <&usim_ck>;
 		ti,bit-shift = <8>;
 		reg = <0x1858>;
@@ -541,6 +608,7 @@
 	trace_clk_div_ck: trace_clk_div_ck {
 		#clock-cells = <0>;
 		compatible = "ti,clkdm-gate-clock";
+		clock-output-names = "trace_clk_div_ck";
 		clocks = <&emu_sys_clkctrl OMAP4_DEBUGSS_CLKCTRL 24>;
 	};
 };
@@ -548,6 +616,7 @@
 &prm_clockdomains {
 	emu_sys_clkdm: emu_sys_clkdm {
 		compatible = "ti,clockdomain";
+		clock-output-names = "emu_sys_clkdm";
 		clocks = <&trace_clk_div_ck>;
 	};
 };
@@ -556,6 +625,7 @@
 	per_hsd_byp_clk_mux_ck: per_hsd_byp_clk_mux_ck@14c {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "per_hsd_byp_clk_mux_ck";
 		clocks = <&sys_clkin_ck>, <&per_hs_clk_div_ck>;
 		ti,bit-shift = <23>;
 		reg = <0x014c>;
@@ -564,6 +634,7 @@
 	dpll_per_ck: dpll_per_ck@140 {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-clock";
+		clock-output-names = "dpll_per_ck";
 		clocks = <&sys_clkin_ck>, <&per_hsd_byp_clk_mux_ck>;
 		reg = <0x0140>, <0x0144>, <0x014c>, <0x0148>;
 	};
@@ -571,6 +642,7 @@
 	dpll_per_m2_ck: dpll_per_m2_ck@150 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_per_m2_ck";
 		clocks = <&dpll_per_ck>;
 		ti,max-div = <31>;
 		reg = <0x0150>;
@@ -580,6 +652,7 @@
 	dpll_per_x2_ck: dpll_per_x2_ck@150 {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-x2-clock";
+		clock-output-names = "dpll_per_x2_ck";
 		clocks = <&dpll_per_ck>;
 		reg = <0x0150>;
 	};
@@ -587,6 +660,7 @@
 	dpll_per_m2x2_ck: dpll_per_m2x2_ck@150 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_per_m2x2_ck";
 		clocks = <&dpll_per_x2_ck>;
 		ti,max-div = <31>;
 		ti,autoidle-shift = <8>;
@@ -598,6 +672,7 @@
 	dpll_per_m3x2_gate_ck: dpll_per_m3x2_gate_ck@154 {
 		#clock-cells = <0>;
 		compatible = "ti,composite-no-wait-gate-clock";
+		clock-output-names = "dpll_per_m3x2_gate_ck";
 		clocks = <&dpll_per_x2_ck>;
 		ti,bit-shift = <8>;
 		reg = <0x0154>;
@@ -606,6 +681,7 @@
 	dpll_per_m3x2_div_ck: dpll_per_m3x2_div_ck@154 {
 		#clock-cells = <0>;
 		compatible = "ti,composite-divider-clock";
+		clock-output-names = "dpll_per_m3x2_div_ck";
 		clocks = <&dpll_per_x2_ck>;
 		ti,max-div = <31>;
 		reg = <0x0154>;
@@ -615,12 +691,14 @@
 	dpll_per_m3x2_ck: dpll_per_m3x2_ck {
 		#clock-cells = <0>;
 		compatible = "ti,composite-clock";
+		clock-output-names = "dpll_per_m3x2_ck";
 		clocks = <&dpll_per_m3x2_gate_ck>, <&dpll_per_m3x2_div_ck>;
 	};
 
 	dpll_per_m4x2_ck: dpll_per_m4x2_ck@158 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_per_m4x2_ck";
 		clocks = <&dpll_per_x2_ck>;
 		ti,max-div = <31>;
 		ti,autoidle-shift = <8>;
@@ -632,6 +710,7 @@
 	dpll_per_m5x2_ck: dpll_per_m5x2_ck@15c {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_per_m5x2_ck";
 		clocks = <&dpll_per_x2_ck>;
 		ti,max-div = <31>;
 		ti,autoidle-shift = <8>;
@@ -643,6 +722,7 @@
 	dpll_per_m6x2_ck: dpll_per_m6x2_ck@160 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_per_m6x2_ck";
 		clocks = <&dpll_per_x2_ck>;
 		ti,max-div = <31>;
 		ti,autoidle-shift = <8>;
@@ -654,6 +734,7 @@
 	dpll_per_m7x2_ck: dpll_per_m7x2_ck@164 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_per_m7x2_ck";
 		clocks = <&dpll_per_x2_ck>;
 		ti,max-div = <31>;
 		ti,autoidle-shift = <8>;
@@ -665,6 +746,7 @@
 	dpll_usb_ck: dpll_usb_ck@180 {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-j-type-clock";
+		clock-output-names = "dpll_usb_ck";
 		clocks = <&sys_clkin_ck>, <&usb_hs_clk_div_ck>;
 		reg = <0x0180>, <0x0184>, <0x018c>, <0x0188>;
 	};
@@ -672,6 +754,7 @@
 	dpll_usb_clkdcoldo_ck: dpll_usb_clkdcoldo_ck@1b4 {
 		#clock-cells = <0>;
 		compatible = "ti,fixed-factor-clock";
+		clock-output-names = "dpll_usb_clkdcoldo_ck";
 		clocks = <&dpll_usb_ck>;
 		ti,clock-div = <1>;
 		ti,autoidle-shift = <8>;
@@ -683,6 +766,7 @@
 	dpll_usb_m2_ck: dpll_usb_m2_ck@190 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_usb_m2_ck";
 		clocks = <&dpll_usb_ck>;
 		ti,max-div = <127>;
 		ti,autoidle-shift = <8>;
@@ -694,6 +778,7 @@
 	ducati_clk_mux_ck: ducati_clk_mux_ck@100 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "ducati_clk_mux_ck";
 		clocks = <&div_core_ck>, <&dpll_per_m6x2_ck>;
 		reg = <0x0100>;
 	};
@@ -701,6 +786,7 @@
 	func_12m_fclk: func_12m_fclk {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "func_12m_fclk";
 		clocks = <&dpll_per_m2x2_ck>;
 		clock-mult = <1>;
 		clock-div = <16>;
@@ -709,6 +795,7 @@
 	func_24m_clk: func_24m_clk {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "func_24m_clk";
 		clocks = <&dpll_per_m2_ck>;
 		clock-mult = <1>;
 		clock-div = <4>;
@@ -717,6 +804,7 @@
 	func_24mc_fclk: func_24mc_fclk {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "func_24mc_fclk";
 		clocks = <&dpll_per_m2x2_ck>;
 		clock-mult = <1>;
 		clock-div = <8>;
@@ -725,6 +813,7 @@
 	func_48m_fclk: func_48m_fclk@108 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "func_48m_fclk";
 		clocks = <&dpll_per_m2x2_ck>;
 		reg = <0x0108>;
 		ti,dividers = <4>, <8>;
@@ -733,6 +822,7 @@
 	func_48mc_fclk: func_48mc_fclk {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "func_48mc_fclk";
 		clocks = <&dpll_per_m2x2_ck>;
 		clock-mult = <1>;
 		clock-div = <4>;
@@ -741,6 +831,7 @@
 	func_64m_fclk: func_64m_fclk@108 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "func_64m_fclk";
 		clocks = <&dpll_per_m4x2_ck>;
 		reg = <0x0108>;
 		ti,dividers = <2>, <4>;
@@ -749,6 +840,7 @@
 	func_96m_fclk: func_96m_fclk@108 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "func_96m_fclk";
 		clocks = <&dpll_per_m2x2_ck>;
 		reg = <0x0108>;
 		ti,dividers = <2>, <4>;
@@ -757,6 +849,7 @@
 	init_60m_fclk: init_60m_fclk@104 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "init_60m_fclk";
 		clocks = <&dpll_usb_m2_ck>;
 		reg = <0x0104>;
 		ti,dividers = <1>, <8>;
@@ -765,6 +858,7 @@
 	per_abe_nc_fclk: per_abe_nc_fclk@108 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "per_abe_nc_fclk";
 		clocks = <&dpll_abe_m2_ck>;
 		reg = <0x0108>;
 		ti,max-div = <2>;
@@ -773,6 +867,7 @@
 	usb_phy_cm_clk32k: usb_phy_cm_clk32k@640 {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
+		clock-output-names = "usb_phy_cm_clk32k";
 		clocks = <&sys_32k_ck>;
 		ti,bit-shift = <8>;
 		reg = <0x0640>;
@@ -782,6 +877,7 @@
 &cm2_clockdomains {
 	l3_init_clkdm: l3_init_clkdm {
 		compatible = "ti,clockdomain";
+		clock-output-names = "l3_init_clkdm";
 		clocks = <&dpll_usb_ck>;
 	};
 };
@@ -790,6 +886,7 @@
 	auxclk0_src_gate_ck: auxclk0_src_gate_ck@310 {
 		#clock-cells = <0>;
 		compatible = "ti,composite-no-wait-gate-clock";
+		clock-output-names = "auxclk0_src_gate_ck";
 		clocks = <&dpll_core_m3x2_ck>;
 		ti,bit-shift = <8>;
 		reg = <0x0310>;
@@ -798,6 +895,7 @@
 	auxclk0_src_mux_ck: auxclk0_src_mux_ck@310 {
 		#clock-cells = <0>;
 		compatible = "ti,composite-mux-clock";
+		clock-output-names = "auxclk0_src_mux_ck";
 		clocks = <&sys_clkin_ck>, <&dpll_core_m3x2_ck>, <&dpll_per_m3x2_ck>;
 		ti,bit-shift = <1>;
 		reg = <0x0310>;
@@ -806,12 +904,14 @@
 	auxclk0_src_ck: auxclk0_src_ck {
 		#clock-cells = <0>;
 		compatible = "ti,composite-clock";
+		clock-output-names = "auxclk0_src_ck";
 		clocks = <&auxclk0_src_gate_ck>, <&auxclk0_src_mux_ck>;
 	};
 
 	auxclk0_ck: auxclk0_ck@310 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "auxclk0_ck";
 		clocks = <&auxclk0_src_ck>;
 		ti,bit-shift = <16>;
 		ti,max-div = <16>;
@@ -821,6 +921,7 @@
 	auxclk1_src_gate_ck: auxclk1_src_gate_ck@314 {
 		#clock-cells = <0>;
 		compatible = "ti,composite-no-wait-gate-clock";
+		clock-output-names = "auxclk1_src_gate_ck";
 		clocks = <&dpll_core_m3x2_ck>;
 		ti,bit-shift = <8>;
 		reg = <0x0314>;
@@ -829,6 +930,7 @@
 	auxclk1_src_mux_ck: auxclk1_src_mux_ck@314 {
 		#clock-cells = <0>;
 		compatible = "ti,composite-mux-clock";
+		clock-output-names = "auxclk1_src_mux_ck";
 		clocks = <&sys_clkin_ck>, <&dpll_core_m3x2_ck>, <&dpll_per_m3x2_ck>;
 		ti,bit-shift = <1>;
 		reg = <0x0314>;
@@ -837,12 +939,14 @@
 	auxclk1_src_ck: auxclk1_src_ck {
 		#clock-cells = <0>;
 		compatible = "ti,composite-clock";
+		clock-output-names = "auxclk1_src_ck";
 		clocks = <&auxclk1_src_gate_ck>, <&auxclk1_src_mux_ck>;
 	};
 
 	auxclk1_ck: auxclk1_ck@314 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "auxclk1_ck";
 		clocks = <&auxclk1_src_ck>;
 		ti,bit-shift = <16>;
 		ti,max-div = <16>;
@@ -852,6 +956,7 @@
 	auxclk2_src_gate_ck: auxclk2_src_gate_ck@318 {
 		#clock-cells = <0>;
 		compatible = "ti,composite-no-wait-gate-clock";
+		clock-output-names = "auxclk2_src_gate_ck";
 		clocks = <&dpll_core_m3x2_ck>;
 		ti,bit-shift = <8>;
 		reg = <0x0318>;
@@ -860,6 +965,7 @@
 	auxclk2_src_mux_ck: auxclk2_src_mux_ck@318 {
 		#clock-cells = <0>;
 		compatible = "ti,composite-mux-clock";
+		clock-output-names = "auxclk2_src_mux_ck";
 		clocks = <&sys_clkin_ck>, <&dpll_core_m3x2_ck>, <&dpll_per_m3x2_ck>;
 		ti,bit-shift = <1>;
 		reg = <0x0318>;
@@ -868,12 +974,14 @@
 	auxclk2_src_ck: auxclk2_src_ck {
 		#clock-cells = <0>;
 		compatible = "ti,composite-clock";
+		clock-output-names = "auxclk2_src_ck";
 		clocks = <&auxclk2_src_gate_ck>, <&auxclk2_src_mux_ck>;
 	};
 
 	auxclk2_ck: auxclk2_ck@318 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "auxclk2_ck";
 		clocks = <&auxclk2_src_ck>;
 		ti,bit-shift = <16>;
 		ti,max-div = <16>;
@@ -883,6 +991,7 @@
 	auxclk3_src_gate_ck: auxclk3_src_gate_ck@31c {
 		#clock-cells = <0>;
 		compatible = "ti,composite-no-wait-gate-clock";
+		clock-output-names = "auxclk3_src_gate_ck";
 		clocks = <&dpll_core_m3x2_ck>;
 		ti,bit-shift = <8>;
 		reg = <0x031c>;
@@ -891,6 +1000,7 @@
 	auxclk3_src_mux_ck: auxclk3_src_mux_ck@31c {
 		#clock-cells = <0>;
 		compatible = "ti,composite-mux-clock";
+		clock-output-names = "auxclk3_src_mux_ck";
 		clocks = <&sys_clkin_ck>, <&dpll_core_m3x2_ck>, <&dpll_per_m3x2_ck>;
 		ti,bit-shift = <1>;
 		reg = <0x031c>;
@@ -899,12 +1009,14 @@
 	auxclk3_src_ck: auxclk3_src_ck {
 		#clock-cells = <0>;
 		compatible = "ti,composite-clock";
+		clock-output-names = "auxclk3_src_ck";
 		clocks = <&auxclk3_src_gate_ck>, <&auxclk3_src_mux_ck>;
 	};
 
 	auxclk3_ck: auxclk3_ck@31c {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "auxclk3_ck";
 		clocks = <&auxclk3_src_ck>;
 		ti,bit-shift = <16>;
 		ti,max-div = <16>;
@@ -914,6 +1026,7 @@
 	auxclk4_src_gate_ck: auxclk4_src_gate_ck@320 {
 		#clock-cells = <0>;
 		compatible = "ti,composite-no-wait-gate-clock";
+		clock-output-names = "auxclk4_src_gate_ck";
 		clocks = <&dpll_core_m3x2_ck>;
 		ti,bit-shift = <8>;
 		reg = <0x0320>;
@@ -922,6 +1035,7 @@
 	auxclk4_src_mux_ck: auxclk4_src_mux_ck@320 {
 		#clock-cells = <0>;
 		compatible = "ti,composite-mux-clock";
+		clock-output-names = "auxclk4_src_mux_ck";
 		clocks = <&sys_clkin_ck>, <&dpll_core_m3x2_ck>, <&dpll_per_m3x2_ck>;
 		ti,bit-shift = <1>;
 		reg = <0x0320>;
@@ -930,12 +1044,14 @@
 	auxclk4_src_ck: auxclk4_src_ck {
 		#clock-cells = <0>;
 		compatible = "ti,composite-clock";
+		clock-output-names = "auxclk4_src_ck";
 		clocks = <&auxclk4_src_gate_ck>, <&auxclk4_src_mux_ck>;
 	};
 
 	auxclk4_ck: auxclk4_ck@320 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "auxclk4_ck";
 		clocks = <&auxclk4_src_ck>;
 		ti,bit-shift = <16>;
 		ti,max-div = <16>;
@@ -945,6 +1061,7 @@
 	auxclk5_src_gate_ck: auxclk5_src_gate_ck@324 {
 		#clock-cells = <0>;
 		compatible = "ti,composite-no-wait-gate-clock";
+		clock-output-names = "auxclk5_src_gate_ck";
 		clocks = <&dpll_core_m3x2_ck>;
 		ti,bit-shift = <8>;
 		reg = <0x0324>;
@@ -953,6 +1070,7 @@
 	auxclk5_src_mux_ck: auxclk5_src_mux_ck@324 {
 		#clock-cells = <0>;
 		compatible = "ti,composite-mux-clock";
+		clock-output-names = "auxclk5_src_mux_ck";
 		clocks = <&sys_clkin_ck>, <&dpll_core_m3x2_ck>, <&dpll_per_m3x2_ck>;
 		ti,bit-shift = <1>;
 		reg = <0x0324>;
@@ -961,12 +1079,14 @@
 	auxclk5_src_ck: auxclk5_src_ck {
 		#clock-cells = <0>;
 		compatible = "ti,composite-clock";
+		clock-output-names = "auxclk5_src_ck";
 		clocks = <&auxclk5_src_gate_ck>, <&auxclk5_src_mux_ck>;
 	};
 
 	auxclk5_ck: auxclk5_ck@324 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "auxclk5_ck";
 		clocks = <&auxclk5_src_ck>;
 		ti,bit-shift = <16>;
 		ti,max-div = <16>;
@@ -976,6 +1096,7 @@
 	auxclkreq0_ck: auxclkreq0_ck@210 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "auxclkreq0_ck";
 		clocks = <&auxclk0_ck>, <&auxclk1_ck>, <&auxclk2_ck>, <&auxclk3_ck>, <&auxclk4_ck>, <&auxclk5_ck>;
 		ti,bit-shift = <2>;
 		reg = <0x0210>;
@@ -984,6 +1105,7 @@
 	auxclkreq1_ck: auxclkreq1_ck@214 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "auxclkreq1_ck";
 		clocks = <&auxclk0_ck>, <&auxclk1_ck>, <&auxclk2_ck>, <&auxclk3_ck>, <&auxclk4_ck>, <&auxclk5_ck>;
 		ti,bit-shift = <2>;
 		reg = <0x0214>;
@@ -992,6 +1114,7 @@
 	auxclkreq2_ck: auxclkreq2_ck@218 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "auxclkreq2_ck";
 		clocks = <&auxclk0_ck>, <&auxclk1_ck>, <&auxclk2_ck>, <&auxclk3_ck>, <&auxclk4_ck>, <&auxclk5_ck>;
 		ti,bit-shift = <2>;
 		reg = <0x0218>;
@@ -1000,6 +1123,7 @@
 	auxclkreq3_ck: auxclkreq3_ck@21c {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "auxclkreq3_ck";
 		clocks = <&auxclk0_ck>, <&auxclk1_ck>, <&auxclk2_ck>, <&auxclk3_ck>, <&auxclk4_ck>, <&auxclk5_ck>;
 		ti,bit-shift = <2>;
 		reg = <0x021c>;
@@ -1008,6 +1132,7 @@
 	auxclkreq4_ck: auxclkreq4_ck@220 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "auxclkreq4_ck";
 		clocks = <&auxclk0_ck>, <&auxclk1_ck>, <&auxclk2_ck>, <&auxclk3_ck>, <&auxclk4_ck>, <&auxclk5_ck>;
 		ti,bit-shift = <2>;
 		reg = <0x0220>;
@@ -1016,6 +1141,7 @@
 	auxclkreq5_ck: auxclkreq5_ck@224 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "auxclkreq5_ck";
 		clocks = <&auxclk0_ck>, <&auxclk1_ck>, <&auxclk2_ck>, <&auxclk3_ck>, <&auxclk4_ck>, <&auxclk5_ck>;
 		ti,bit-shift = <2>;
 		reg = <0x0224>;
@@ -1025,6 +1151,7 @@
 &cm1 {
 	mpuss_cm: mpuss_cm@300 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "mpuss_cm";
 		reg = <0x300 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -1032,6 +1159,7 @@
 
 		mpuss_clkctrl: clk@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "mpuss_clkctrl";
 			reg = <0x20 0x4>;
 			#clock-cells = <2>;
 		};
@@ -1039,6 +1167,7 @@
 
 	tesla_cm: tesla_cm@400 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "tesla_cm";
 		reg = <0x400 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -1046,6 +1175,7 @@
 
 		tesla_clkctrl: clk@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "tesla_clkctrl";
 			reg = <0x20 0x4>;
 			#clock-cells = <2>;
 		};
@@ -1053,6 +1183,7 @@
 
 	abe_cm: abe_cm@500 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "abe_cm";
 		reg = <0x500 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -1060,6 +1191,7 @@
 
 		abe_clkctrl: clk@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "abe_clkctrl";
 			reg = <0x20 0x6c>;
 			#clock-cells = <2>;
 		};
@@ -1070,6 +1202,7 @@
 &cm2 {
 	l4_ao_cm: l4_ao_cm@600 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "l4_ao_cm";
 		reg = <0x600 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -1077,6 +1210,7 @@
 
 		l4_ao_clkctrl: clk@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "l4_ao_clkctrl";
 			reg = <0x20 0x1c>;
 			#clock-cells = <2>;
 		};
@@ -1084,6 +1218,7 @@
 
 	l3_1_cm: l3_1_cm@700 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "l3_1_cm";
 		reg = <0x700 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -1091,6 +1226,7 @@
 
 		l3_1_clkctrl: clk@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "l3_1_clkctrl";
 			reg = <0x20 0x4>;
 			#clock-cells = <2>;
 		};
@@ -1098,6 +1234,7 @@
 
 	l3_2_cm: l3_2_cm@800 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "l3_2_cm";
 		reg = <0x800 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -1105,6 +1242,7 @@
 
 		l3_2_clkctrl: clk@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "l3_2_clkctrl";
 			reg = <0x20 0x14>;
 			#clock-cells = <2>;
 		};
@@ -1112,6 +1250,7 @@
 
 	ducati_cm: ducati_cm@900 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "ducati_cm";
 		reg = <0x900 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -1119,6 +1258,7 @@
 
 		ducati_clkctrl: clk@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "ducati_clkctrl";
 			reg = <0x20 0x4>;
 			#clock-cells = <2>;
 		};
@@ -1126,6 +1266,7 @@
 
 	l3_dma_cm: l3_dma_cm@a00 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "l3_dma_cm";
 		reg = <0xa00 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -1133,6 +1274,7 @@
 
 		l3_dma_clkctrl: clk@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "l3_dma_clkctrl";
 			reg = <0x20 0x4>;
 			#clock-cells = <2>;
 		};
@@ -1140,6 +1282,7 @@
 
 	l3_emif_cm: l3_emif_cm@b00 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "l3_emif_cm";
 		reg = <0xb00 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -1147,6 +1290,7 @@
 
 		l3_emif_clkctrl: clk@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "l3_emif_clkctrl";
 			reg = <0x20 0x1c>;
 			#clock-cells = <2>;
 		};
@@ -1154,6 +1298,7 @@
 
 	d2d_cm: d2d_cm@c00 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "d2d_cm";
 		reg = <0xc00 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -1161,6 +1306,7 @@
 
 		d2d_clkctrl: clk@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "d2d_clkctrl";
 			reg = <0x20 0x4>;
 			#clock-cells = <2>;
 		};
@@ -1168,6 +1314,7 @@
 
 	l4_cfg_cm: l4_cfg_cm@d00 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "l4_cfg_cm";
 		reg = <0xd00 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -1175,6 +1322,7 @@
 
 		l4_cfg_clkctrl: clk@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "l4_cfg_clkctrl";
 			reg = <0x20 0x14>;
 			#clock-cells = <2>;
 		};
@@ -1182,6 +1330,7 @@
 
 	l3_instr_cm: l3_instr_cm@e00 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "l3_instr_cm";
 		reg = <0xe00 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -1189,6 +1338,7 @@
 
 		l3_instr_clkctrl: clk@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "l3_instr_clkctrl";
 			reg = <0x20 0x24>;
 			#clock-cells = <2>;
 		};
@@ -1196,6 +1346,7 @@
 
 	ivahd_cm: ivahd_cm@f00 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "ivahd_cm";
 		reg = <0xf00 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -1203,6 +1354,7 @@
 
 		ivahd_clkctrl: clk@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "ivahd_clkctrl";
 			reg = <0x20 0xc>;
 			#clock-cells = <2>;
 		};
@@ -1210,6 +1362,7 @@
 
 	iss_cm: iss_cm@1000 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "iss_cm";
 		reg = <0x1000 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -1217,6 +1370,7 @@
 
 		iss_clkctrl: clk@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "iss_clkctrl";
 			reg = <0x20 0xc>;
 			#clock-cells = <2>;
 		};
@@ -1224,6 +1378,7 @@
 
 	l3_dss_cm: l3_dss_cm@1100 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "l3_dss_cm";
 		reg = <0x1100 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -1231,6 +1386,7 @@
 
 		l3_dss_clkctrl: clk@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "l3_dss_clkctrl";
 			reg = <0x20 0x4>;
 			#clock-cells = <2>;
 		};
@@ -1238,6 +1394,7 @@
 
 	l3_gfx_cm: l3_gfx_cm@1200 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "l3_gfx_cm";
 		reg = <0x1200 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -1245,6 +1402,7 @@
 
 		l3_gfx_clkctrl: clk@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "l3_gfx_clkctrl";
 			reg = <0x20 0x4>;
 			#clock-cells = <2>;
 		};
@@ -1252,6 +1410,7 @@
 
 	l3_init_cm: l3_init_cm@1300 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "l3_init_cm";
 		reg = <0x1300 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -1259,26 +1418,30 @@
 
 		l3_init_clkctrl: clk@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "l3_init_clkctrl";
 			reg = <0x20 0xc4>;
 			#clock-cells = <2>;
 		};
 	};
 
-	l4_per_cm: l4_per_cm@1400 {
+	l4_per_cm: clock@1400 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "l4_per_cm";
 		reg = <0x1400 0x200>;
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0 0x1400 0x200>;
 
 		l4_per_clkctrl: clock@20 {
-			compatible = "ti,clkctrl-l4-per", "ti,clkctrl";
+			compatible = "ti,clkctrl";
+			clock-output-names = "l4_per_clkctrl";
 			reg = <0x20 0x144>;
 			#clock-cells = <2>;
 		};
 
 		l4_secure_clkctrl: clock@1a0 {
-			compatible = "ti,clkctrl-l4-secure", "ti,clkctrl";
+			compatible = "ti,clkctrl";
+			clock-output-names = "l4_secure_clkctrl";
 			reg = <0x1a0 0x3c>;
 			#clock-cells = <2>;
 		};
@@ -1288,6 +1451,7 @@
 &prm {
 	l4_wkup_cm: l4_wkup_cm@1800 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "l4_wkup_cm";
 		reg = <0x1800 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -1295,6 +1459,7 @@
 
 		l4_wkup_clkctrl: clk@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "l4_wkup_clkctrl";
 			reg = <0x20 0x5c>;
 			#clock-cells = <2>;
 		};
@@ -1302,6 +1467,7 @@
 
 	emu_sys_cm: emu_sys_cm@1a00 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "emu_sys_cm";
 		reg = <0x1a00 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -1309,6 +1475,7 @@
 
 		emu_sys_clkctrl: clk@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "emu_sys_clkctrl";
 			reg = <0x20 0x4>;
 			#clock-cells = <2>;
 		};
diff --git a/arch/arm/boot/dts/omap5-core-thermal.dtsi b/arch/arm/boot/dts/omap5-core-thermal.dtsi
index 02e76338bfbc..e0d8e39a0014 100644
--- a/arch/arm/boot/dts/omap5-core-thermal.dtsi
+++ b/arch/arm/boot/dts/omap5-core-thermal.dtsi
@@ -1,12 +1,9 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Device Tree Source for OMAP543x SoC CORE thermal
  *
  * Copyright (C) 2013 Texas Instruments Incorporated - https://www.ti.com/
  * Contact: Eduardo Valentin <eduardo.valentin@ti.com>
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2.  This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
  */
 
 #include <dt-bindings/thermal/thermal.h>
diff --git a/arch/arm/boot/dts/omap5-gpu-thermal.dtsi b/arch/arm/boot/dts/omap5-gpu-thermal.dtsi
index bf8fa9372e57..1b4b7d9136c8 100644
--- a/arch/arm/boot/dts/omap5-gpu-thermal.dtsi
+++ b/arch/arm/boot/dts/omap5-gpu-thermal.dtsi
@@ -1,12 +1,9 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Device Tree Source for OMAP543x SoC GPU thermal
  *
  * Copyright (C) 2013 Texas Instruments Incorporated - https://www.ti.com/
  * Contact: Eduardo Valentin <eduardo.valentin@ti.com>
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2.  This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
  */
 
 #include <dt-bindings/thermal/thermal.h>
diff --git a/arch/arm/boot/dts/omap5-igep0050.dts b/arch/arm/boot/dts/omap5-igep0050.dts
index 76e499d89d24..3851120857d7 100644
--- a/arch/arm/boot/dts/omap5-igep0050.dts
+++ b/arch/arm/boot/dts/omap5-igep0050.dts
@@ -128,7 +128,7 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		ethernet: usbether@3 {
+		ethernet: ethernet@3 {
 			compatible = "usb424,7500";
 			reg = <3>;
 		};
diff --git a/arch/arm/boot/dts/omap5-l4.dtsi b/arch/arm/boot/dts/omap5-l4.dtsi
index 06cc3a19ddaa..3b505fe415ed 100644
--- a/arch/arm/boot/dts/omap5-l4.dtsi
+++ b/arch/arm/boot/dts/omap5-l4.dtsi
@@ -482,7 +482,7 @@
 				clocks = <&usb_phy_cm_clk32k>,
 				<&sys_clkin>,
 				<&l3init_clkctrl OMAP5_USB_OTG_SS_CLKCTRL 8>;
-				clock-names =	"wkupclk",
+				clock-names = "wkupclk",
 				"sysclk",
 				"refclk";
 				#phy-cells = <0>;
diff --git a/arch/arm/boot/dts/omap5-uevm.dts b/arch/arm/boot/dts/omap5-uevm.dts
index 51d5fcae5081..453da9f18a99 100644
--- a/arch/arm/boot/dts/omap5-uevm.dts
+++ b/arch/arm/boot/dts/omap5-uevm.dts
@@ -209,7 +209,7 @@
 		#size-cells = <0>;
 	};
 
-	ethernet: usbether@3 {
+	ethernet: ethernet@3 {
 		compatible = "usb424,9730";
 		reg = <3>;
 	};
diff --git a/arch/arm/boot/dts/omap54xx-clocks.dtsi b/arch/arm/boot/dts/omap54xx-clocks.dtsi
index 42f2c447727d..5cf3b0e78c15 100644
--- a/arch/arm/boot/dts/omap54xx-clocks.dtsi
+++ b/arch/arm/boot/dts/omap54xx-clocks.dtsi
@@ -8,12 +8,14 @@
 	pad_clks_src_ck: pad_clks_src_ck {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "pad_clks_src_ck";
 		clock-frequency = <12000000>;
 	};
 
 	pad_clks_ck: pad_clks_ck@108 {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
+		clock-output-names = "pad_clks_ck";
 		clocks = <&pad_clks_src_ck>;
 		ti,bit-shift = <8>;
 		reg = <0x0108>;
@@ -22,18 +24,21 @@
 	secure_32k_clk_src_ck: secure_32k_clk_src_ck {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "secure_32k_clk_src_ck";
 		clock-frequency = <32768>;
 	};
 
 	slimbus_src_clk: slimbus_src_clk {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "slimbus_src_clk";
 		clock-frequency = <12000000>;
 	};
 
 	slimbus_clk: slimbus_clk@108 {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
+		clock-output-names = "slimbus_clk";
 		clocks = <&slimbus_src_clk>;
 		ti,bit-shift = <10>;
 		reg = <0x0108>;
@@ -42,66 +47,77 @@
 	sys_32k_ck: sys_32k_ck {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "sys_32k_ck";
 		clock-frequency = <32768>;
 	};
 
 	virt_12000000_ck: virt_12000000_ck {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "virt_12000000_ck";
 		clock-frequency = <12000000>;
 	};
 
 	virt_13000000_ck: virt_13000000_ck {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "virt_13000000_ck";
 		clock-frequency = <13000000>;
 	};
 
 	virt_16800000_ck: virt_16800000_ck {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "virt_16800000_ck";
 		clock-frequency = <16800000>;
 	};
 
 	virt_19200000_ck: virt_19200000_ck {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "virt_19200000_ck";
 		clock-frequency = <19200000>;
 	};
 
 	virt_26000000_ck: virt_26000000_ck {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "virt_26000000_ck";
 		clock-frequency = <26000000>;
 	};
 
 	virt_27000000_ck: virt_27000000_ck {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "virt_27000000_ck";
 		clock-frequency = <27000000>;
 	};
 
 	virt_38400000_ck: virt_38400000_ck {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "virt_38400000_ck";
 		clock-frequency = <38400000>;
 	};
 
 	xclk60mhsp1_ck: xclk60mhsp1_ck {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "xclk60mhsp1_ck";
 		clock-frequency = <60000000>;
 	};
 
 	xclk60mhsp2_ck: xclk60mhsp2_ck {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "xclk60mhsp2_ck";
 		clock-frequency = <60000000>;
 	};
 
 	dpll_abe_ck: dpll_abe_ck@1e0 {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-m4xen-clock";
+		clock-output-names = "dpll_abe_ck";
 		clocks = <&abe_dpll_clk_mux>, <&abe_dpll_bypass_clk_mux>;
 		reg = <0x01e0>, <0x01e4>, <0x01ec>, <0x01e8>;
 	};
@@ -109,12 +125,14 @@
 	dpll_abe_x2_ck: dpll_abe_x2_ck {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-x2-clock";
+		clock-output-names = "dpll_abe_x2_ck";
 		clocks = <&dpll_abe_ck>;
 	};
 
 	dpll_abe_m2x2_ck: dpll_abe_m2x2_ck@1f0 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_abe_m2x2_ck";
 		clocks = <&dpll_abe_x2_ck>;
 		ti,max-div = <31>;
 		reg = <0x01f0>;
@@ -124,6 +142,7 @@
 	abe_24m_fclk: abe_24m_fclk {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "abe_24m_fclk";
 		clocks = <&dpll_abe_m2x2_ck>;
 		clock-mult = <1>;
 		clock-div = <8>;
@@ -132,6 +151,7 @@
 	abe_clk: abe_clk@108 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "abe_clk";
 		clocks = <&dpll_abe_m2x2_ck>;
 		ti,max-div = <4>;
 		reg = <0x0108>;
@@ -141,6 +161,7 @@
 	abe_iclk: abe_iclk@528 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "abe_iclk";
 		clocks = <&aess_fclk>;
 		ti,bit-shift = <24>;
 		reg = <0x0528>;
@@ -150,6 +171,7 @@
 	abe_lp_clk_div: abe_lp_clk_div {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "abe_lp_clk_div";
 		clocks = <&dpll_abe_m2x2_ck>;
 		clock-mult = <1>;
 		clock-div = <16>;
@@ -158,6 +180,7 @@
 	dpll_abe_m3x2_ck: dpll_abe_m3x2_ck@1f4 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_abe_m3x2_ck";
 		clocks = <&dpll_abe_x2_ck>;
 		ti,max-div = <31>;
 		reg = <0x01f4>;
@@ -167,6 +190,7 @@
 	dpll_core_byp_mux: dpll_core_byp_mux@12c {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "dpll_core_byp_mux";
 		clocks = <&sys_clkin>, <&dpll_abe_m3x2_ck>;
 		ti,bit-shift = <23>;
 		reg = <0x012c>;
@@ -175,6 +199,7 @@
 	dpll_core_ck: dpll_core_ck@120 {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-core-clock";
+		clock-output-names = "dpll_core_ck";
 		clocks = <&sys_clkin>, <&dpll_core_byp_mux>;
 		reg = <0x0120>, <0x0124>, <0x012c>, <0x0128>;
 	};
@@ -182,12 +207,14 @@
 	dpll_core_x2_ck: dpll_core_x2_ck {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-x2-clock";
+		clock-output-names = "dpll_core_x2_ck";
 		clocks = <&dpll_core_ck>;
 	};
 
 	dpll_core_h21x2_ck: dpll_core_h21x2_ck@150 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_core_h21x2_ck";
 		clocks = <&dpll_core_x2_ck>;
 		ti,max-div = <63>;
 		reg = <0x0150>;
@@ -197,6 +224,7 @@
 	c2c_fclk: c2c_fclk {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "c2c_fclk";
 		clocks = <&dpll_core_h21x2_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
@@ -205,6 +233,7 @@
 	c2c_iclk: c2c_iclk {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "c2c_iclk";
 		clocks = <&c2c_fclk>;
 		clock-mult = <1>;
 		clock-div = <2>;
@@ -213,6 +242,7 @@
 	dpll_core_h11x2_ck: dpll_core_h11x2_ck@138 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_core_h11x2_ck";
 		clocks = <&dpll_core_x2_ck>;
 		ti,max-div = <63>;
 		reg = <0x0138>;
@@ -222,6 +252,7 @@
 	dpll_core_h12x2_ck: dpll_core_h12x2_ck@13c {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_core_h12x2_ck";
 		clocks = <&dpll_core_x2_ck>;
 		ti,max-div = <63>;
 		reg = <0x013c>;
@@ -231,6 +262,7 @@
 	dpll_core_h13x2_ck: dpll_core_h13x2_ck@140 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_core_h13x2_ck";
 		clocks = <&dpll_core_x2_ck>;
 		ti,max-div = <63>;
 		reg = <0x0140>;
@@ -240,6 +272,7 @@
 	dpll_core_h14x2_ck: dpll_core_h14x2_ck@144 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_core_h14x2_ck";
 		clocks = <&dpll_core_x2_ck>;
 		ti,max-div = <63>;
 		reg = <0x0144>;
@@ -249,6 +282,7 @@
 	dpll_core_h22x2_ck: dpll_core_h22x2_ck@154 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_core_h22x2_ck";
 		clocks = <&dpll_core_x2_ck>;
 		ti,max-div = <63>;
 		reg = <0x0154>;
@@ -258,6 +292,7 @@
 	dpll_core_h23x2_ck: dpll_core_h23x2_ck@158 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_core_h23x2_ck";
 		clocks = <&dpll_core_x2_ck>;
 		ti,max-div = <63>;
 		reg = <0x0158>;
@@ -267,6 +302,7 @@
 	dpll_core_h24x2_ck: dpll_core_h24x2_ck@15c {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_core_h24x2_ck";
 		clocks = <&dpll_core_x2_ck>;
 		ti,max-div = <63>;
 		reg = <0x015c>;
@@ -276,6 +312,7 @@
 	dpll_core_m2_ck: dpll_core_m2_ck@130 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_core_m2_ck";
 		clocks = <&dpll_core_ck>;
 		ti,max-div = <31>;
 		reg = <0x0130>;
@@ -285,6 +322,7 @@
 	dpll_core_m3x2_ck: dpll_core_m3x2_ck@134 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_core_m3x2_ck";
 		clocks = <&dpll_core_x2_ck>;
 		ti,max-div = <31>;
 		reg = <0x0134>;
@@ -294,6 +332,7 @@
 	iva_dpll_hs_clk_div: iva_dpll_hs_clk_div {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "iva_dpll_hs_clk_div";
 		clocks = <&dpll_core_h12x2_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
@@ -302,6 +341,7 @@
 	dpll_iva_byp_mux: dpll_iva_byp_mux@1ac {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "dpll_iva_byp_mux";
 		clocks = <&sys_clkin>, <&iva_dpll_hs_clk_div>;
 		ti,bit-shift = <23>;
 		reg = <0x01ac>;
@@ -310,6 +350,7 @@
 	dpll_iva_ck: dpll_iva_ck@1a0 {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-clock";
+		clock-output-names = "dpll_iva_ck";
 		clocks = <&sys_clkin>, <&dpll_iva_byp_mux>;
 		reg = <0x01a0>, <0x01a4>, <0x01ac>, <0x01a8>;
 		assigned-clocks = <&dpll_iva_ck>;
@@ -319,12 +360,14 @@
 	dpll_iva_x2_ck: dpll_iva_x2_ck {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-x2-clock";
+		clock-output-names = "dpll_iva_x2_ck";
 		clocks = <&dpll_iva_ck>;
 	};
 
 	dpll_iva_h11x2_ck: dpll_iva_h11x2_ck@1b8 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_iva_h11x2_ck";
 		clocks = <&dpll_iva_x2_ck>;
 		ti,max-div = <63>;
 		reg = <0x01b8>;
@@ -336,6 +379,7 @@
 	dpll_iva_h12x2_ck: dpll_iva_h12x2_ck@1bc {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_iva_h12x2_ck";
 		clocks = <&dpll_iva_x2_ck>;
 		ti,max-div = <63>;
 		reg = <0x01bc>;
@@ -347,6 +391,7 @@
 	mpu_dpll_hs_clk_div: mpu_dpll_hs_clk_div {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "mpu_dpll_hs_clk_div";
 		clocks = <&dpll_core_h12x2_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
@@ -355,6 +400,7 @@
 	dpll_mpu_ck: dpll_mpu_ck@160 {
 		#clock-cells = <0>;
 		compatible = "ti,omap5-mpu-dpll-clock";
+		clock-output-names = "dpll_mpu_ck";
 		clocks = <&sys_clkin>, <&mpu_dpll_hs_clk_div>;
 		reg = <0x0160>, <0x0164>, <0x016c>, <0x0168>;
 	};
@@ -362,6 +408,7 @@
 	dpll_mpu_m2_ck: dpll_mpu_m2_ck@170 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_mpu_m2_ck";
 		clocks = <&dpll_mpu_ck>;
 		ti,max-div = <31>;
 		reg = <0x0170>;
@@ -371,6 +418,7 @@
 	per_dpll_hs_clk_div: per_dpll_hs_clk_div {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "per_dpll_hs_clk_div";
 		clocks = <&dpll_abe_m3x2_ck>;
 		clock-mult = <1>;
 		clock-div = <2>;
@@ -379,6 +427,7 @@
 	usb_dpll_hs_clk_div: usb_dpll_hs_clk_div {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "usb_dpll_hs_clk_div";
 		clocks = <&dpll_abe_m3x2_ck>;
 		clock-mult = <1>;
 		clock-div = <3>;
@@ -387,6 +436,7 @@
 	l3_iclk_div: l3_iclk_div@100 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "l3_iclk_div";
 		ti,max-div = <2>;
 		ti,bit-shift = <4>;
 		reg = <0x100>;
@@ -397,6 +447,7 @@
 	gpu_l3_iclk: gpu_l3_iclk {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "gpu_l3_iclk";
 		clocks = <&l3_iclk_div>;
 		clock-mult = <1>;
 		clock-div = <1>;
@@ -405,6 +456,7 @@
 	l4_root_clk_div: l4_root_clk_div@100 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "l4_root_clk_div";
 		ti,max-div = <2>;
 		ti,bit-shift = <8>;
 		reg = <0x100>;
@@ -415,6 +467,7 @@
 	slimbus1_slimbus_clk: slimbus1_slimbus_clk@560 {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
+		clock-output-names = "slimbus1_slimbus_clk";
 		clocks = <&slimbus_clk>;
 		ti,bit-shift = <11>;
 		reg = <0x0560>;
@@ -423,6 +476,7 @@
 	aess_fclk: aess_fclk@528 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "aess_fclk";
 		clocks = <&abe_clk>;
 		ti,bit-shift = <24>;
 		ti,max-div = <2>;
@@ -432,6 +486,7 @@
 	mcasp_sync_mux_ck: mcasp_sync_mux_ck@540 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "mcasp_sync_mux_ck";
 		clocks = <&abe_24m_fclk>, <&dss_syc_gfclk_div>, <&func_24m_clk>;
 		ti,bit-shift = <26>;
 		reg = <0x0540>;
@@ -440,6 +495,7 @@
 	mcasp_gfclk: mcasp_gfclk@540 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "mcasp_gfclk";
 		clocks = <&mcasp_sync_mux_ck>, <&pad_clks_ck>, <&slimbus_clk>;
 		ti,bit-shift = <24>;
 		reg = <0x0540>;
@@ -448,6 +504,7 @@
 	dummy_ck: dummy_ck {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
+		clock-output-names = "dummy_ck";
 		clock-frequency = <0>;
 	};
 };
@@ -455,6 +512,7 @@
 	sys_clkin: sys_clkin@110 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "sys_clkin";
 		clocks = <&virt_12000000_ck>, <&virt_13000000_ck>, <&virt_16800000_ck>, <&virt_19200000_ck>, <&virt_26000000_ck>, <&virt_27000000_ck>, <&virt_38400000_ck>;
 		reg = <0x0110>;
 		ti,index-starts-at-one;
@@ -463,6 +521,7 @@
 	abe_dpll_bypass_clk_mux: abe_dpll_bypass_clk_mux@108 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "abe_dpll_bypass_clk_mux";
 		clocks = <&sys_clkin>, <&sys_32k_ck>;
 		reg = <0x0108>;
 	};
@@ -470,6 +529,7 @@
 	abe_dpll_clk_mux: abe_dpll_clk_mux@10c {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "abe_dpll_clk_mux";
 		clocks = <&sys_clkin>, <&sys_32k_ck>;
 		reg = <0x010c>;
 	};
@@ -477,6 +537,7 @@
 	custefuse_sys_gfclk_div: custefuse_sys_gfclk_div {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "custefuse_sys_gfclk_div";
 		clocks = <&sys_clkin>;
 		clock-mult = <1>;
 		clock-div = <2>;
@@ -485,6 +546,7 @@
 	dss_syc_gfclk_div: dss_syc_gfclk_div {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "dss_syc_gfclk_div";
 		clocks = <&sys_clkin>;
 		clock-mult = <1>;
 		clock-div = <1>;
@@ -493,6 +555,7 @@
 	wkupaon_iclk_mux: wkupaon_iclk_mux@108 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "wkupaon_iclk_mux";
 		clocks = <&sys_clkin>, <&abe_lp_clk_div>;
 		reg = <0x0108>;
 	};
@@ -500,6 +563,7 @@
 	l3instr_ts_gclk_div: l3instr_ts_gclk_div {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "l3instr_ts_gclk_div";
 		clocks = <&wkupaon_iclk_mux>;
 		clock-mult = <1>;
 		clock-div = <1>;
@@ -511,6 +575,7 @@
 	dpll_per_byp_mux: dpll_per_byp_mux@14c {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "dpll_per_byp_mux";
 		clocks = <&sys_clkin>, <&per_dpll_hs_clk_div>;
 		ti,bit-shift = <23>;
 		reg = <0x014c>;
@@ -519,6 +584,7 @@
 	dpll_per_ck: dpll_per_ck@140 {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-clock";
+		clock-output-names = "dpll_per_ck";
 		clocks = <&sys_clkin>, <&dpll_per_byp_mux>;
 		reg = <0x0140>, <0x0144>, <0x014c>, <0x0148>;
 	};
@@ -526,12 +592,14 @@
 	dpll_per_x2_ck: dpll_per_x2_ck {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-x2-clock";
+		clock-output-names = "dpll_per_x2_ck";
 		clocks = <&dpll_per_ck>;
 	};
 
 	dpll_per_h11x2_ck: dpll_per_h11x2_ck@158 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_per_h11x2_ck";
 		clocks = <&dpll_per_x2_ck>;
 		ti,max-div = <63>;
 		reg = <0x0158>;
@@ -541,6 +609,7 @@
 	dpll_per_h12x2_ck: dpll_per_h12x2_ck@15c {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_per_h12x2_ck";
 		clocks = <&dpll_per_x2_ck>;
 		ti,max-div = <63>;
 		reg = <0x015c>;
@@ -550,6 +619,7 @@
 	dpll_per_h14x2_ck: dpll_per_h14x2_ck@164 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_per_h14x2_ck";
 		clocks = <&dpll_per_x2_ck>;
 		ti,max-div = <63>;
 		reg = <0x0164>;
@@ -559,6 +629,7 @@
 	dpll_per_m2_ck: dpll_per_m2_ck@150 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_per_m2_ck";
 		clocks = <&dpll_per_ck>;
 		ti,max-div = <31>;
 		reg = <0x0150>;
@@ -568,6 +639,7 @@
 	dpll_per_m2x2_ck: dpll_per_m2x2_ck@150 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_per_m2x2_ck";
 		clocks = <&dpll_per_x2_ck>;
 		ti,max-div = <31>;
 		reg = <0x0150>;
@@ -577,6 +649,7 @@
 	dpll_per_m3x2_ck: dpll_per_m3x2_ck@154 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_per_m3x2_ck";
 		clocks = <&dpll_per_x2_ck>;
 		ti,max-div = <31>;
 		reg = <0x0154>;
@@ -586,6 +659,7 @@
 	dpll_unipro1_ck: dpll_unipro1_ck@200 {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-clock";
+		clock-output-names = "dpll_unipro1_ck";
 		clocks = <&sys_clkin>, <&sys_clkin>;
 		reg = <0x0200>, <0x0204>, <0x020c>, <0x0208>;
 	};
@@ -593,6 +667,7 @@
 	dpll_unipro1_clkdcoldo: dpll_unipro1_clkdcoldo {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "dpll_unipro1_clkdcoldo";
 		clocks = <&dpll_unipro1_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
@@ -601,6 +676,7 @@
 	dpll_unipro1_m2_ck: dpll_unipro1_m2_ck@210 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_unipro1_m2_ck";
 		clocks = <&dpll_unipro1_ck>;
 		ti,max-div = <127>;
 		reg = <0x0210>;
@@ -610,6 +686,7 @@
 	dpll_unipro2_ck: dpll_unipro2_ck@1c0 {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-clock";
+		clock-output-names = "dpll_unipro2_ck";
 		clocks = <&sys_clkin>, <&sys_clkin>;
 		reg = <0x01c0>, <0x01c4>, <0x01cc>, <0x01c8>;
 	};
@@ -617,6 +694,7 @@
 	dpll_unipro2_clkdcoldo: dpll_unipro2_clkdcoldo {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "dpll_unipro2_clkdcoldo";
 		clocks = <&dpll_unipro2_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
@@ -625,6 +703,7 @@
 	dpll_unipro2_m2_ck: dpll_unipro2_m2_ck@1d0 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_unipro2_m2_ck";
 		clocks = <&dpll_unipro2_ck>;
 		ti,max-div = <127>;
 		reg = <0x01d0>;
@@ -634,6 +713,7 @@
 	dpll_usb_byp_mux: dpll_usb_byp_mux@18c {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "dpll_usb_byp_mux";
 		clocks = <&sys_clkin>, <&usb_dpll_hs_clk_div>;
 		ti,bit-shift = <23>;
 		reg = <0x018c>;
@@ -642,6 +722,7 @@
 	dpll_usb_ck: dpll_usb_ck@180 {
 		#clock-cells = <0>;
 		compatible = "ti,omap4-dpll-j-type-clock";
+		clock-output-names = "dpll_usb_ck";
 		clocks = <&sys_clkin>, <&dpll_usb_byp_mux>;
 		reg = <0x0180>, <0x0184>, <0x018c>, <0x0188>;
 	};
@@ -649,6 +730,7 @@
 	dpll_usb_clkdcoldo: dpll_usb_clkdcoldo {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "dpll_usb_clkdcoldo";
 		clocks = <&dpll_usb_ck>;
 		clock-mult = <1>;
 		clock-div = <1>;
@@ -657,6 +739,7 @@
 	dpll_usb_m2_ck: dpll_usb_m2_ck@190 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "dpll_usb_m2_ck";
 		clocks = <&dpll_usb_ck>;
 		ti,max-div = <127>;
 		reg = <0x0190>;
@@ -666,6 +749,7 @@
 	func_128m_clk: func_128m_clk {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "func_128m_clk";
 		clocks = <&dpll_per_h11x2_ck>;
 		clock-mult = <1>;
 		clock-div = <2>;
@@ -674,6 +758,7 @@
 	func_12m_fclk: func_12m_fclk {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "func_12m_fclk";
 		clocks = <&dpll_per_m2x2_ck>;
 		clock-mult = <1>;
 		clock-div = <16>;
@@ -682,6 +767,7 @@
 	func_24m_clk: func_24m_clk {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "func_24m_clk";
 		clocks = <&dpll_per_m2_ck>;
 		clock-mult = <1>;
 		clock-div = <4>;
@@ -690,6 +776,7 @@
 	func_48m_fclk: func_48m_fclk {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "func_48m_fclk";
 		clocks = <&dpll_per_m2x2_ck>;
 		clock-mult = <1>;
 		clock-div = <4>;
@@ -698,6 +785,7 @@
 	func_96m_fclk: func_96m_fclk {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
+		clock-output-names = "func_96m_fclk";
 		clocks = <&dpll_per_m2x2_ck>;
 		clock-mult = <1>;
 		clock-div = <2>;
@@ -706,6 +794,7 @@
 	l3init_60m_fclk: l3init_60m_fclk@104 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "l3init_60m_fclk";
 		clocks = <&dpll_usb_m2_ck>;
 		reg = <0x0104>;
 		ti,dividers = <1>, <8>;
@@ -714,6 +803,7 @@
 	iss_ctrlclk: iss_ctrlclk@1320 {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
+		clock-output-names = "iss_ctrlclk";
 		clocks = <&func_96m_fclk>;
 		ti,bit-shift = <8>;
 		reg = <0x1320>;
@@ -722,6 +812,7 @@
 	lli_txphy_clk: lli_txphy_clk@f20 {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
+		clock-output-names = "lli_txphy_clk";
 		clocks = <&dpll_unipro1_clkdcoldo>;
 		ti,bit-shift = <8>;
 		reg = <0x0f20>;
@@ -730,6 +821,7 @@
 	lli_txphy_ls_clk: lli_txphy_ls_clk@f20 {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
+		clock-output-names = "lli_txphy_ls_clk";
 		clocks = <&dpll_unipro1_m2_ck>;
 		ti,bit-shift = <9>;
 		reg = <0x0f20>;
@@ -738,6 +830,7 @@
 	usb_phy_cm_clk32k: usb_phy_cm_clk32k@640 {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
+		clock-output-names = "usb_phy_cm_clk32k";
 		clocks = <&sys_32k_ck>;
 		ti,bit-shift = <8>;
 		reg = <0x0640>;
@@ -746,6 +839,7 @@
 	fdif_fclk: fdif_fclk@1328 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "fdif_fclk";
 		clocks = <&dpll_per_h11x2_ck>;
 		ti,bit-shift = <24>;
 		ti,max-div = <2>;
@@ -755,6 +849,7 @@
 	gpu_core_gclk_mux: gpu_core_gclk_mux@1520 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "gpu_core_gclk_mux";
 		clocks = <&dpll_core_h14x2_ck>, <&dpll_per_h14x2_ck>;
 		ti,bit-shift = <24>;
 		reg = <0x1520>;
@@ -763,6 +858,7 @@
 	gpu_hyd_gclk_mux: gpu_hyd_gclk_mux@1520 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "gpu_hyd_gclk_mux";
 		clocks = <&dpll_core_h14x2_ck>, <&dpll_per_h14x2_ck>;
 		ti,bit-shift = <25>;
 		reg = <0x1520>;
@@ -771,6 +867,7 @@
 	hsi_fclk: hsi_fclk@1638 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "hsi_fclk";
 		clocks = <&dpll_per_m2x2_ck>;
 		ti,bit-shift = <24>;
 		ti,max-div = <2>;
@@ -781,6 +878,7 @@
 &cm_core_clockdomains {
 	l3init_clkdm: l3init_clkdm {
 		compatible = "ti,clockdomain";
+		clock-output-names = "l3init_clkdm";
 		clocks = <&dpll_usb_ck>;
 	};
 };
@@ -789,6 +887,7 @@
 	auxclk0_src_gate_ck: auxclk0_src_gate_ck@310 {
 		#clock-cells = <0>;
 		compatible = "ti,composite-no-wait-gate-clock";
+		clock-output-names = "auxclk0_src_gate_ck";
 		clocks = <&dpll_core_m3x2_ck>;
 		ti,bit-shift = <8>;
 		reg = <0x0310>;
@@ -797,6 +896,7 @@
 	auxclk0_src_mux_ck: auxclk0_src_mux_ck@310 {
 		#clock-cells = <0>;
 		compatible = "ti,composite-mux-clock";
+		clock-output-names = "auxclk0_src_mux_ck";
 		clocks = <&sys_clkin>, <&dpll_core_m3x2_ck>, <&dpll_per_m3x2_ck>;
 		ti,bit-shift = <1>;
 		reg = <0x0310>;
@@ -805,12 +905,14 @@
 	auxclk0_src_ck: auxclk0_src_ck {
 		#clock-cells = <0>;
 		compatible = "ti,composite-clock";
+		clock-output-names = "auxclk0_src_ck";
 		clocks = <&auxclk0_src_gate_ck>, <&auxclk0_src_mux_ck>;
 	};
 
 	auxclk0_ck: auxclk0_ck@310 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "auxclk0_ck";
 		clocks = <&auxclk0_src_ck>;
 		ti,bit-shift = <16>;
 		ti,max-div = <16>;
@@ -820,6 +922,7 @@
 	auxclk1_src_gate_ck: auxclk1_src_gate_ck@314 {
 		#clock-cells = <0>;
 		compatible = "ti,composite-no-wait-gate-clock";
+		clock-output-names = "auxclk1_src_gate_ck";
 		clocks = <&dpll_core_m3x2_ck>;
 		ti,bit-shift = <8>;
 		reg = <0x0314>;
@@ -828,6 +931,7 @@
 	auxclk1_src_mux_ck: auxclk1_src_mux_ck@314 {
 		#clock-cells = <0>;
 		compatible = "ti,composite-mux-clock";
+		clock-output-names = "auxclk1_src_mux_ck";
 		clocks = <&sys_clkin>, <&dpll_core_m3x2_ck>, <&dpll_per_m3x2_ck>;
 		ti,bit-shift = <1>;
 		reg = <0x0314>;
@@ -836,12 +940,14 @@
 	auxclk1_src_ck: auxclk1_src_ck {
 		#clock-cells = <0>;
 		compatible = "ti,composite-clock";
+		clock-output-names = "auxclk1_src_ck";
 		clocks = <&auxclk1_src_gate_ck>, <&auxclk1_src_mux_ck>;
 	};
 
 	auxclk1_ck: auxclk1_ck@314 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "auxclk1_ck";
 		clocks = <&auxclk1_src_ck>;
 		ti,bit-shift = <16>;
 		ti,max-div = <16>;
@@ -851,6 +957,7 @@
 	auxclk2_src_gate_ck: auxclk2_src_gate_ck@318 {
 		#clock-cells = <0>;
 		compatible = "ti,composite-no-wait-gate-clock";
+		clock-output-names = "auxclk2_src_gate_ck";
 		clocks = <&dpll_core_m3x2_ck>;
 		ti,bit-shift = <8>;
 		reg = <0x0318>;
@@ -859,6 +966,7 @@
 	auxclk2_src_mux_ck: auxclk2_src_mux_ck@318 {
 		#clock-cells = <0>;
 		compatible = "ti,composite-mux-clock";
+		clock-output-names = "auxclk2_src_mux_ck";
 		clocks = <&sys_clkin>, <&dpll_core_m3x2_ck>, <&dpll_per_m3x2_ck>;
 		ti,bit-shift = <1>;
 		reg = <0x0318>;
@@ -867,12 +975,14 @@
 	auxclk2_src_ck: auxclk2_src_ck {
 		#clock-cells = <0>;
 		compatible = "ti,composite-clock";
+		clock-output-names = "auxclk2_src_ck";
 		clocks = <&auxclk2_src_gate_ck>, <&auxclk2_src_mux_ck>;
 	};
 
 	auxclk2_ck: auxclk2_ck@318 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "auxclk2_ck";
 		clocks = <&auxclk2_src_ck>;
 		ti,bit-shift = <16>;
 		ti,max-div = <16>;
@@ -882,6 +992,7 @@
 	auxclk3_src_gate_ck: auxclk3_src_gate_ck@31c {
 		#clock-cells = <0>;
 		compatible = "ti,composite-no-wait-gate-clock";
+		clock-output-names = "auxclk3_src_gate_ck";
 		clocks = <&dpll_core_m3x2_ck>;
 		ti,bit-shift = <8>;
 		reg = <0x031c>;
@@ -890,6 +1001,7 @@
 	auxclk3_src_mux_ck: auxclk3_src_mux_ck@31c {
 		#clock-cells = <0>;
 		compatible = "ti,composite-mux-clock";
+		clock-output-names = "auxclk3_src_mux_ck";
 		clocks = <&sys_clkin>, <&dpll_core_m3x2_ck>, <&dpll_per_m3x2_ck>;
 		ti,bit-shift = <1>;
 		reg = <0x031c>;
@@ -898,12 +1010,14 @@
 	auxclk3_src_ck: auxclk3_src_ck {
 		#clock-cells = <0>;
 		compatible = "ti,composite-clock";
+		clock-output-names = "auxclk3_src_ck";
 		clocks = <&auxclk3_src_gate_ck>, <&auxclk3_src_mux_ck>;
 	};
 
 	auxclk3_ck: auxclk3_ck@31c {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "auxclk3_ck";
 		clocks = <&auxclk3_src_ck>;
 		ti,bit-shift = <16>;
 		ti,max-div = <16>;
@@ -913,6 +1027,7 @@
 	auxclk4_src_gate_ck: auxclk4_src_gate_ck@320 {
 		#clock-cells = <0>;
 		compatible = "ti,composite-no-wait-gate-clock";
+		clock-output-names = "auxclk4_src_gate_ck";
 		clocks = <&dpll_core_m3x2_ck>;
 		ti,bit-shift = <8>;
 		reg = <0x0320>;
@@ -921,6 +1036,7 @@
 	auxclk4_src_mux_ck: auxclk4_src_mux_ck@320 {
 		#clock-cells = <0>;
 		compatible = "ti,composite-mux-clock";
+		clock-output-names = "auxclk4_src_mux_ck";
 		clocks = <&sys_clkin>, <&dpll_core_m3x2_ck>, <&dpll_per_m3x2_ck>;
 		ti,bit-shift = <1>;
 		reg = <0x0320>;
@@ -929,12 +1045,14 @@
 	auxclk4_src_ck: auxclk4_src_ck {
 		#clock-cells = <0>;
 		compatible = "ti,composite-clock";
+		clock-output-names = "auxclk4_src_ck";
 		clocks = <&auxclk4_src_gate_ck>, <&auxclk4_src_mux_ck>;
 	};
 
 	auxclk4_ck: auxclk4_ck@320 {
 		#clock-cells = <0>;
 		compatible = "ti,divider-clock";
+		clock-output-names = "auxclk4_ck";
 		clocks = <&auxclk4_src_ck>;
 		ti,bit-shift = <16>;
 		ti,max-div = <16>;
@@ -944,6 +1062,7 @@
 	auxclkreq0_ck: auxclkreq0_ck@210 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "auxclkreq0_ck";
 		clocks = <&auxclk0_ck>, <&auxclk1_ck>, <&auxclk2_ck>, <&auxclk3_ck>, <&auxclk4_ck>;
 		ti,bit-shift = <2>;
 		reg = <0x0210>;
@@ -952,6 +1071,7 @@
 	auxclkreq1_ck: auxclkreq1_ck@214 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "auxclkreq1_ck";
 		clocks = <&auxclk0_ck>, <&auxclk1_ck>, <&auxclk2_ck>, <&auxclk3_ck>, <&auxclk4_ck>;
 		ti,bit-shift = <2>;
 		reg = <0x0214>;
@@ -960,6 +1080,7 @@
 	auxclkreq2_ck: auxclkreq2_ck@218 {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "auxclkreq2_ck";
 		clocks = <&auxclk0_ck>, <&auxclk1_ck>, <&auxclk2_ck>, <&auxclk3_ck>, <&auxclk4_ck>;
 		ti,bit-shift = <2>;
 		reg = <0x0218>;
@@ -968,6 +1089,7 @@
 	auxclkreq3_ck: auxclkreq3_ck@21c {
 		#clock-cells = <0>;
 		compatible = "ti,mux-clock";
+		clock-output-names = "auxclkreq3_ck";
 		clocks = <&auxclk0_ck>, <&auxclk1_ck>, <&auxclk2_ck>, <&auxclk3_ck>, <&auxclk4_ck>;
 		ti,bit-shift = <2>;
 		reg = <0x021c>;
@@ -977,6 +1099,7 @@
 &cm_core_aon {
 	mpu_cm: mpu_cm@300 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "mpu_cm";
 		reg = <0x300 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -984,6 +1107,7 @@
 
 		mpu_clkctrl: clk@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "mpu_clkctrl";
 			reg = <0x20 0x4>;
 			#clock-cells = <2>;
 		};
@@ -991,6 +1115,7 @@
 
 	dsp_cm: dsp_cm@400 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "dsp_cm";
 		reg = <0x400 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -998,6 +1123,7 @@
 
 		dsp_clkctrl: clk@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "dsp_clkctrl";
 			reg = <0x20 0x4>;
 			#clock-cells = <2>;
 		};
@@ -1005,6 +1131,7 @@
 
 	abe_cm: abe_cm@500 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "abe_cm";
 		reg = <0x500 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -1012,6 +1139,7 @@
 
 		abe_clkctrl: clk@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "abe_clkctrl";
 			reg = <0x20 0x64>;
 			#clock-cells = <2>;
 		};
@@ -1022,6 +1150,7 @@
 &cm_core {
 	l3main1_cm: l3main1_cm@700 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "l3main1_cm";
 		reg = <0x700 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -1029,6 +1158,7 @@
 
 		l3main1_clkctrl: clk@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "l3main1_clkctrl";
 			reg = <0x20 0x4>;
 			#clock-cells = <2>;
 		};
@@ -1036,6 +1166,7 @@
 
 	l3main2_cm: l3main2_cm@800 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "l3main2_cm";
 		reg = <0x800 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -1043,6 +1174,7 @@
 
 		l3main2_clkctrl: clk@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "l3main2_clkctrl";
 			reg = <0x20 0x4>;
 			#clock-cells = <2>;
 		};
@@ -1050,6 +1182,7 @@
 
 	ipu_cm: ipu_cm@900 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "ipu_cm";
 		reg = <0x900 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -1057,6 +1190,7 @@
 
 		ipu_clkctrl: clk@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "ipu_clkctrl";
 			reg = <0x20 0x4>;
 			#clock-cells = <2>;
 		};
@@ -1064,6 +1198,7 @@
 
 	dma_cm: dma_cm@a00 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "dma_cm";
 		reg = <0xa00 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -1071,6 +1206,7 @@
 
 		dma_clkctrl: clk@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "dma_clkctrl";
 			reg = <0x20 0x4>;
 			#clock-cells = <2>;
 		};
@@ -1078,6 +1214,7 @@
 
 	emif_cm: emif_cm@b00 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "emif_cm";
 		reg = <0xb00 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -1085,6 +1222,7 @@
 
 		emif_clkctrl: clk@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "emif_clkctrl";
 			reg = <0x20 0x1c>;
 			#clock-cells = <2>;
 		};
@@ -1092,6 +1230,7 @@
 
 	l4cfg_cm: l4cfg_cm@d00 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "l4cfg_cm";
 		reg = <0xd00 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -1099,6 +1238,7 @@
 
 		l4cfg_clkctrl: clk@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "l4cfg_clkctrl";
 			reg = <0x20 0x14>;
 			#clock-cells = <2>;
 		};
@@ -1106,6 +1246,7 @@
 
 	l3instr_cm: l3instr_cm@e00 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "l3instr_cm";
 		reg = <0xe00 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -1113,26 +1254,30 @@
 
 		l3instr_clkctrl: clk@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "l3instr_clkctrl";
 			reg = <0x20 0xc>;
 			#clock-cells = <2>;
 		};
 	};
 
-	l4per_cm: l4per_cm@1000 {
+	l4per_cm: clock@1000 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "l4per_cm";
 		reg = <0x1000 0x200>;
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0 0x1000 0x200>;
 
 		l4per_clkctrl: clock@20 {
-			compatible = "ti,clkctrl-l4per", "ti,clkctrl";
+			compatible = "ti,clkctrl";
+			clock-output-names = "l4per_clkctrl";
 			reg = <0x20 0x15c>;
 			#clock-cells = <2>;
 		};
 
 		l4sec_clkctrl: clock@1a0 {
-			compatible = "ti,clkctrl-l4sec", "ti,clkctrl";
+			compatible = "ti,clkctrl";
+			clock-output-names = "l4sec_clkctrl";
 			reg = <0x1a0 0x3c>;
 			#clock-cells = <2>;
 		};
@@ -1140,6 +1285,7 @@
 
 	dss_cm: dss_cm@1400 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "dss_cm";
 		reg = <0x1400 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -1147,6 +1293,7 @@
 
 		dss_clkctrl: clk@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "dss_clkctrl";
 			reg = <0x20 0x4>;
 			#clock-cells = <2>;
 		};
@@ -1154,6 +1301,7 @@
 
 	gpu_cm: gpu_cm@1500 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "gpu_cm";
 		reg = <0x1500 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -1161,6 +1309,7 @@
 
 		gpu_clkctrl: clk@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "gpu_clkctrl";
 			reg = <0x20 0x4>;
 			#clock-cells = <2>;
 		};
@@ -1168,6 +1317,7 @@
 
 	l3init_cm: l3init_cm@1600 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "l3init_cm";
 		reg = <0x1600 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -1175,6 +1325,7 @@
 
 		l3init_clkctrl: clk@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "l3init_clkctrl";
 			reg = <0x20 0xd4>;
 			#clock-cells = <2>;
 		};
@@ -1184,6 +1335,7 @@
 &prm {
 	wkupaon_cm: wkupaon_cm@1900 {
 		compatible = "ti,omap4-cm";
+		clock-output-names = "wkupaon_cm";
 		reg = <0x1900 0x100>;
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -1191,6 +1343,7 @@
 
 		wkupaon_clkctrl: clk@20 {
 			compatible = "ti,clkctrl";
+			clock-output-names = "wkupaon_clkctrl";
 			reg = <0x20 0x5c>;
 			#clock-cells = <2>;
 		};
@@ -1201,6 +1354,7 @@
 	fref_xtal_ck: fref_xtal_ck {
 		#clock-cells = <0>;
 		compatible = "ti,gate-clock";
+		clock-output-names = "fref_xtal_ck";
 		clocks = <&sys_clkin>;
 		ti,bit-shift = <28>;
 		reg = <0x14>;
diff --git a/arch/arm/boot/dts/openbmc-flash-layout-64-alt.dtsi b/arch/arm/boot/dts/openbmc-flash-layout-64-alt.dtsi
new file mode 100644
index 000000000000..650525867561
--- /dev/null
+++ b/arch/arm/boot/dts/openbmc-flash-layout-64-alt.dtsi
@@ -0,0 +1,35 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2020 Bytedance.
+ */
+
+partitions {
+	compatible = "fixed-partitions";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	u-boot@0 {
+		reg = <0x0 0xe0000>; // 896KB
+		label = "alt-u-boot";
+	};
+
+	u-boot-env@e0000 {
+		reg = <0xe0000 0x20000>; // 128KB
+		label = "alt-u-boot-env";
+	};
+
+	kernel@100000 {
+		reg = <0x100000 0x900000>; // 9MB
+		label = "alt-kernel";
+	};
+
+	rofs@a00000 {
+		reg = <0xa00000 0x2000000>; // 32MB
+		label = "alt-rofs";
+	};
+
+	rwfs@6000000 {
+		reg = <0x2a00000 0x1600000>; // 22MB
+		label = "alt-rwfs";
+	};
+};
diff --git a/arch/arm/boot/dts/openbmc-flash-layout-64.dtsi b/arch/arm/boot/dts/openbmc-flash-layout-64.dtsi
index 31f59de5190b..7af41361c480 100644
--- a/arch/arm/boot/dts/openbmc-flash-layout-64.dtsi
+++ b/arch/arm/boot/dts/openbmc-flash-layout-64.dtsi
@@ -28,7 +28,7 @@ partitions {
 		label = "rofs";
 	};
 
-	rwfs@6000000 {
+	rwfs@2a00000 {
 		reg = <0x2a00000 0x1600000>; // 22MB
 		label = "rwfs";
 	};
diff --git a/arch/arm/boot/dts/openbmc-flash-layout.dtsi b/arch/arm/boot/dts/openbmc-flash-layout.dtsi
index 6c26524e93e1..b47e14063c38 100644
--- a/arch/arm/boot/dts/openbmc-flash-layout.dtsi
+++ b/arch/arm/boot/dts/openbmc-flash-layout.dtsi
@@ -20,7 +20,7 @@ partitions {
 		label = "kernel";
 	};
 
-	rofs@c0000 {
+	rofs@4c0000 {
 		reg = <0x4c0000 0x1740000>;
 		label = "rofs";
 	};
diff --git a/arch/arm/boot/dts/orion5x-lacie-d2-network.dts b/arch/arm/boot/dts/orion5x-lacie-d2-network.dts
index 422958d13d42..03471d30bfd9 100644
--- a/arch/arm/boot/dts/orion5x-lacie-d2-network.dts
+++ b/arch/arm/boot/dts/orion5x-lacie-d2-network.dts
@@ -1,10 +1,7 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Copyright (C) 2014 Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
  * Copyright (C) 2009 Simon Guinot <sguinot@lacie.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 /dts-v1/;
diff --git a/arch/arm/boot/dts/orion5x-lacie-ethernet-disk-mini-v2.dts b/arch/arm/boot/dts/orion5x-lacie-ethernet-disk-mini-v2.dts
index 0043e0040153..f17e25ac98dd 100644
--- a/arch/arm/boot/dts/orion5x-lacie-ethernet-disk-mini-v2.dts
+++ b/arch/arm/boot/dts/orion5x-lacie-ethernet-disk-mini-v2.dts
@@ -1,10 +1,5 @@
-/*
- * Copyright (C) 2012 Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
+// SPDX-License-Identifier: GPL-2.0-only
+// Copyright (C) 2012 Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
 
 /*
  * TODO: add Orion USB device port init when kernel.org support is added.
diff --git a/arch/arm/boot/dts/orion5x-maxtor-shared-storage-2.dts b/arch/arm/boot/dts/orion5x-maxtor-shared-storage-2.dts
index 0ca6208a267d..d57859998350 100644
--- a/arch/arm/boot/dts/orion5x-maxtor-shared-storage-2.dts
+++ b/arch/arm/boot/dts/orion5x-maxtor-shared-storage-2.dts
@@ -1,10 +1,7 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Copyright (C) 2014 Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
  * Copyright (C) Sylver Bruneau <sylver.bruneau@googlemail.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 /dts-v1/;
diff --git a/arch/arm/boot/dts/orion5x-mv88f5181.dtsi b/arch/arm/boot/dts/orion5x-mv88f5181.dtsi
index f667012b26ca..819f9efb7058 100644
--- a/arch/arm/boot/dts/orion5x-mv88f5181.dtsi
+++ b/arch/arm/boot/dts/orion5x-mv88f5181.dtsi
@@ -1,10 +1,5 @@
-/*
- * Copyright (C) 2016 Jamie Lentin <jm@lentin.co.uk>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
+// SPDX-License-Identifier: GPL-2.0-only
+// Copyright (C) 2016 Jamie Lentin <jm@lentin.co.uk>
 
 #include "orion5x.dtsi"
 
diff --git a/arch/arm/boot/dts/orion5x-mv88f5182.dtsi b/arch/arm/boot/dts/orion5x-mv88f5182.dtsi
index d1ed71c60209..86b87fb26dc9 100644
--- a/arch/arm/boot/dts/orion5x-mv88f5182.dtsi
+++ b/arch/arm/boot/dts/orion5x-mv88f5182.dtsi
@@ -1,10 +1,5 @@
-/*
- * Copyright (C) 2014 Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
+// SPDX-License-Identifier: GPL-2.0-only
+// Copyright (C) 2014 Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
 
 #include "orion5x.dtsi"
 
diff --git a/arch/arm/boot/dts/orion5x-netgear-wnr854t.dts b/arch/arm/boot/dts/orion5x-netgear-wnr854t.dts
index ea081afa469d..4f4888ec9138 100644
--- a/arch/arm/boot/dts/orion5x-netgear-wnr854t.dts
+++ b/arch/arm/boot/dts/orion5x-netgear-wnr854t.dts
@@ -1,10 +1,5 @@
-/*
- * Copyright (C) 2016 Jamie Lentin <jm@lentin.co.uk>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
+// SPDX-License-Identifier: GPL-2.0-only
+// Copyright (C) 2016 Jamie Lentin <jm@lentin.co.uk>
 
 /dts-v1/;
 
diff --git a/arch/arm/boot/dts/orion5x-rd88f5182-nas.dts b/arch/arm/boot/dts/orion5x-rd88f5182-nas.dts
index 487324f7c54e..fd78aa02a3c5 100644
--- a/arch/arm/boot/dts/orion5x-rd88f5182-nas.dts
+++ b/arch/arm/boot/dts/orion5x-rd88f5182-nas.dts
@@ -1,10 +1,5 @@
-/*
- * Copyright (C) 2014 Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
+// SPDX-License-Identifier: GPL-2.0-only
+// Copyright (C) 2014 Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
 
 /dts-v1/;
 
diff --git a/arch/arm/boot/dts/orion5x.dtsi b/arch/arm/boot/dts/orion5x.dtsi
index 61e631b3fd8b..2d41f5c166ee 100644
--- a/arch/arm/boot/dts/orion5x.dtsi
+++ b/arch/arm/boot/dts/orion5x.dtsi
@@ -1,10 +1,5 @@
-/*
- * Copyright (C) 2012 Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
+// SPDX-License-Identifier: GPL-2.0-only
+// Copyright (C) 2012 Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
 
 #define MBUS_ID(target,attributes) (((target) << 24) | ((attributes) << 16))
 
diff --git a/arch/arm/boot/dts/ox810se-wd-mbwe.dts b/arch/arm/boot/dts/ox810se-wd-mbwe.dts
index 7e2fcb220aea..c59e06ff2423 100644
--- a/arch/arm/boot/dts/ox810se-wd-mbwe.dts
+++ b/arch/arm/boot/dts/ox810se-wd-mbwe.dts
@@ -103,6 +103,10 @@
 	};
 };
 
+&etha {
+	status = "okay";
+};
+
 &uart1 {
 	status = "okay";
 
diff --git a/arch/arm/boot/dts/ox810se.dtsi b/arch/arm/boot/dts/ox810se.dtsi
index 0755e5864c4a..96c0745f7b70 100644
--- a/arch/arm/boot/dts/ox810se.dtsi
+++ b/arch/arm/boot/dts/ox810se.dtsi
@@ -81,6 +81,24 @@
 		ranges;
 		interrupt-parent = <&intc>;
 
+		etha: ethernet@40400000 {
+			compatible = "oxsemi,ox810se-dwmac", "snps,dwmac";
+			reg = <0x40400000 0x2000>;
+			interrupts = <8>;
+			interrupt-names = "macirq";
+			mac-address = [000000000000]; /* Filled in by U-Boot */
+			phy-mode = "rgmii";
+
+			clocks = <&stdclk 6>, <&gmacclk>;
+			clock-names = "gmac", "stmmaceth";
+			resets = <&reset 6>;
+
+			/* Regmap for sys registers */
+			oxsemi,sys-ctrl = <&sys>;
+
+			status = "disabled";
+		};
+
 		apb-bridge@44000000 {
 			#address-cells = <1>;
 			#size-cells = <1>;
diff --git a/arch/arm/boot/dts/ox820.dtsi b/arch/arm/boot/dts/ox820.dtsi
index 90846a7655b4..dde4364892bf 100644
--- a/arch/arm/boot/dts/ox820.dtsi
+++ b/arch/arm/boot/dts/ox820.dtsi
@@ -287,7 +287,7 @@
 				clocks = <&armclk>;
 			};
 
-			gic: gic@1000 {
+			gic: interrupt-controller@1000 {
 				compatible = "arm,arm11mp-gic";
 				interrupt-controller;
 				#interrupt-cells = <3>;
diff --git a/arch/arm/boot/dts/pxa25x.dtsi b/arch/arm/boot/dts/pxa25x.dtsi
index a248bf038033..5f8300e356ad 100644
--- a/arch/arm/boot/dts/pxa25x.dtsi
+++ b/arch/arm/boot/dts/pxa25x.dtsi
@@ -38,9 +38,12 @@
 			compatible = "marvell,pdma-1.0";
 			reg = <0x40000000 0x10000>;
 			interrupts = <25>;
-			#dma-channels = <16>;
 			#dma-cells = <2>;
+			/* For backwards compatibility: */
+			#dma-channels = <16>;
+			dma-channels = <16>;
 			#dma-requests = <40>;
+			dma-requests = <40>;
 			status = "okay";
 		};
 
diff --git a/arch/arm/boot/dts/pxa27x.dtsi b/arch/arm/boot/dts/pxa27x.dtsi
index ccbecad9c5c7..a2cbfb3be609 100644
--- a/arch/arm/boot/dts/pxa27x.dtsi
+++ b/arch/arm/boot/dts/pxa27x.dtsi
@@ -12,9 +12,12 @@
 			compatible = "marvell,pdma-1.0";
 			reg = <0x40000000 0x10000>;
 			interrupts = <25>;
-			#dma-channels = <32>;
 			#dma-cells = <2>;
+			/* For backwards compatibility: */
+			#dma-channels = <32>;
+			dma-channels = <32>;
 			#dma-requests = <75>;
+			dma-requests = <75>;
 			status = "okay";
 		};
 
diff --git a/arch/arm/boot/dts/pxa300-raumfeld-common.dtsi b/arch/arm/boot/dts/pxa300-raumfeld-common.dtsi
index 8a6721d436bd..147c99191dc2 100644
--- a/arch/arm/boot/dts/pxa300-raumfeld-common.dtsi
+++ b/arch/arm/boot/dts/pxa300-raumfeld-common.dtsi
@@ -189,31 +189,31 @@
 
 		regulators {
 			regulator-v3 {
-				regulator-compatible= "V3(DCDC)";
+				regulator-compatible = "V3(DCDC)";
 				regulator-min-microvolt = <725000>;
 				regulator-max-microvolt = <1800000>;
 			};
 
 			regulator-v4 {
-				regulator-compatible= "V4(DCDC)";
+				regulator-compatible = "V4(DCDC)";
 				regulator-min-microvolt = <725000>;
 				regulator-max-microvolt = <1800000>;
 			};
 
 			regulator-v5 {
-				regulator-compatible= "V5(LDO)";
+				regulator-compatible = "V5(LDO)";
 				regulator-min-microvolt = <1700000>;
 				regulator-max-microvolt = <2000000>;
 			};
 
 			reg_vcc_sdio: regulator-v6 {
-				regulator-compatible= "V6(LDO)";
+				regulator-compatible = "V6(LDO)";
 				regulator-min-microvolt = <3300000>;
 				regulator-max-microvolt = <3300000>;
 			};
 
 			regulator-v7 {
-				regulator-compatible= "V7(LDO)";
+				regulator-compatible = "V7(LDO)";
 				regulator-min-microvolt = <1800000>;
 				regulator-max-microvolt = <3300000>;
 			};
diff --git a/arch/arm/boot/dts/pxa3xx.dtsi b/arch/arm/boot/dts/pxa3xx.dtsi
index d19674812cd2..f9c216f91865 100644
--- a/arch/arm/boot/dts/pxa3xx.dtsi
+++ b/arch/arm/boot/dts/pxa3xx.dtsi
@@ -122,9 +122,12 @@
 			compatible = "marvell,pdma-1.0";
 			reg = <0x40000000 0x10000>;
 			interrupts = <25>;
-			#dma-channels = <32>;
 			#dma-cells = <2>;
+			/* For backwards compatibility: */
+			#dma-channels = <32>;
+			dma-channels = <32>;
 			#dma-requests = <100>;
+			dma-requests = <100>;
 			status = "okay";
 		};
 
diff --git a/arch/arm/boot/dts/qcom-apq8016-sbc.dts b/arch/arm/boot/dts/qcom-apq8016-sbc.dts
new file mode 100644
index 000000000000..4ccd2dca74a2
--- /dev/null
+++ b/arch/arm/boot/dts/qcom-apq8016-sbc.dts
@@ -0,0 +1,2 @@
+// SPDX-License-Identifier: GPL-2.0-only
+#include "arm64/qcom/apq8016-sbc.dts"
diff --git a/arch/arm/boot/dts/qcom-apq8026-asus-sparrow.dts b/arch/arm/boot/dts/qcom-apq8026-asus-sparrow.dts
new file mode 100644
index 000000000000..215613c65250
--- /dev/null
+++ b/arch/arm/boot/dts/qcom-apq8026-asus-sparrow.dts
@@ -0,0 +1,300 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2022, Luca Weiss <luca@z3ntu.xyz>
+ */
+
+/dts-v1/;
+
+#include "qcom-msm8226.dtsi"
+#include "qcom-pm8226.dtsi"
+
+/delete-node/ &adsp_region;
+
+/ {
+	model = "ASUS ZenWatch 2";
+	compatible = "asus,sparrow", "qcom,apq8026";
+	chassis-type = "watch";
+	qcom,msm-id = <199 0x20000>;
+	qcom,board-id = <8 3005>;
+
+	reserved-memory {
+		sbl_region: sbl@2f00000 {
+			reg = <0x02f00000 0x100000>;
+			no-map;
+		};
+		external_image_region: external-image@3100000 {
+			reg = <0x3100000 0x200000>;
+			no-map;
+		};
+		peripheral_region: peripheral@3300000 {
+			reg = <0x3300000 0x600000>;
+			no-map;
+		};
+		adsp_region: adsp@3900000 {
+			reg = <0x3900000 0x1400000>;
+			no-map;
+		};
+		modem_region: modem@4d00000 {
+			reg = <0x4d00000 0x1b00000>;
+			no-map;
+		};
+		modem_efs_region: modem-efs@7f00000 {
+			reg = <0x7f00000 0x100000>;
+			no-map;
+		};
+	};
+
+	vreg_wlan: wlan-regulator {
+		compatible = "regulator-fixed";
+
+		regulator-name = "wl-reg";
+		regulator-min-microvolt = <2950000>;
+		regulator-max-microvolt = <2950000>;
+
+		gpio = <&tlmm 35 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&wlan_regulator_default_state>;
+	};
+};
+
+&adsp {
+	status = "okay";
+};
+
+&blsp1_uart1 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&blsp1_uart1_default_state>;
+
+	bluetooth {
+		compatible = "brcm,bcm43430a1-bt";
+		max-speed = <3000000>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&bluetooth_default_state>;
+
+		host-wakeup-gpios = <&tlmm 48 GPIO_ACTIVE_HIGH>;
+		device-wakeup-gpios = <&tlmm 61 GPIO_ACTIVE_HIGH>;
+		shutdown-gpios = <&tlmm 34 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&pm8226_vib {
+	status = "okay";
+};
+
+&rpm_requests {
+	pm8226-regulators {
+		compatible = "qcom,rpm-pm8226-regulators";
+
+		pm8226_s3: s3 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1300000>;
+		};
+		pm8226_s4: s4 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2200000>;
+		};
+		pm8226_s5: s5 {
+			regulator-min-microvolt = <1150000>;
+			regulator-max-microvolt = <1150000>;
+		};
+
+		pm8226_l1: l1 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+		};
+		pm8226_l2: l2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+		pm8226_l3: l3 {
+			regulator-min-microvolt = <750000>;
+			regulator-max-microvolt = <1337500>;
+		};
+		pm8226_l4: l4 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+		pm8226_l5: l5 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+		pm8226_l6: l6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+		pm8226_l7: l7 {
+			regulator-min-microvolt = <1900000>;
+			regulator-max-microvolt = <1900000>;
+		};
+		pm8226_l8: l8 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+		pm8226_l9: l9 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+		pm8226_l10: l10 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+		pm8226_l12: l12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+		pm8226_l14: l14 {
+			regulator-min-microvolt = <2750000>;
+			regulator-max-microvolt = <2750000>;
+		};
+		pm8226_l15: l15 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+		};
+		pm8226_l16: l16 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+		};
+		pm8226_l17: l17 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+		};
+		pm8226_l18: l18 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+		};
+		pm8226_l19: l19 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+		};
+		pm8226_l20: l20 {
+			regulator-min-microvolt = <3075000>;
+			regulator-max-microvolt = <3075000>;
+		};
+		pm8226_l21: l21 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+		pm8226_l22: l22 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+		pm8226_l23: l23 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+		pm8226_l24: l24 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1350000>;
+		};
+		pm8226_l25: l25 {
+			regulator-min-microvolt = <1775000>;
+			regulator-max-microvolt = <2125000>;
+		};
+		pm8226_l26: l26 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+		};
+		pm8226_l27: l27 {
+			regulator-min-microvolt = <2050000>;
+			regulator-max-microvolt = <2050000>;
+		};
+		pm8226_l28: l28 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8226_lvs1: lvs1 {};
+	};
+};
+
+&sdhc_1 {
+	status = "okay";
+
+	vmmc-supply = <&pm8226_l17>;
+	vqmmc-supply = <&pm8226_l6>;
+
+	bus-width = <8>;
+	non-removable;
+};
+
+&sdhc_3 {
+	status = "okay";
+
+	max-frequency = <100000000>;
+	non-removable;
+
+	vmmc-supply = <&vreg_wlan>;
+	vqmmc-supply = <&pm8226_l6>;
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	wifi@1 {
+		compatible = "brcm,bcm43430a1-fmac", "brcm,bcm4329-fmac";
+		reg = <1>;
+
+		interrupts-extended = <&tlmm 46 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-names = "host-wake";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&wlan_hostwake_default_state>;
+	};
+};
+
+&smbb {
+	qcom,fast-charge-safe-current = <1500000>;
+	qcom,fast-charge-current-limit = <350000>;
+	qcom,fast-charge-safe-voltage = <4430000>;
+	qcom,fast-charge-high-threshold-voltage = <4400000>;
+	qcom,auto-recharge-threshold-voltage = <4300000>;
+	qcom,minimum-input-voltage = <4400000>;
+};
+
+&tlmm {
+	blsp1_uart1_default_state: blsp1-uart1-default-state {
+		pins = "gpio0", "gpio1", "gpio2", "gpio3";
+		function = "blsp_uart1";
+		drive-strength = <8>;
+		bias-disable;
+	};
+
+	bluetooth_default_state: bluetooth-default-state {
+		pins = "gpio48", "gpio61";
+		function = "gpio";
+		drive-strength = <8>;
+		bias-disable;
+		input-enable;
+	};
+
+	wlan_hostwake_default_state: wlan-hostwake-default-state {
+		pins = "gpio46";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+		input-enable;
+	};
+
+	wlan_regulator_default_state: wlan-regulator-default-state {
+		pins = "gpio35";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-up;
+	};
+};
+
+&usb {
+	status = "okay";
+	extcon = <&smbb>;
+	dr_mode = "peripheral";
+};
+
+&usb_hs_phy {
+	extcon = <&smbb>;
+	v1p8-supply = <&pm8226_l10>;
+	v3p3-supply = <&pm8226_l20>;
+};
diff --git a/arch/arm/boot/dts/qcom-apq8026-lg-lenok.dts b/arch/arm/boot/dts/qcom-apq8026-lg-lenok.dts
index f350c4e8c194..193569f0ca5f 100644
--- a/arch/arm/boot/dts/qcom-apq8026-lg-lenok.dts
+++ b/arch/arm/boot/dts/qcom-apq8026-lg-lenok.dts
@@ -8,6 +8,8 @@
 #include "qcom-msm8226.dtsi"
 #include "qcom-pm8226.dtsi"
 
+/delete-node/ &adsp_region;
+
 / {
 	model = "LG G Watch R";
 	compatible = "lg,lenok", "qcom,apq8026";
@@ -16,11 +18,46 @@
 
 	aliases {
 		serial0 = &blsp1_uart3;
+		serial1 = &blsp1_uart4;
 	};
 
 	chosen {
 		stdout-path = "serial0:115200n8";
 	};
+
+	reserved-memory {
+		adsp_region: adsp@3300000 {
+			reg = <0x03300000 0x1400000>;
+			no-map;
+		};
+	};
+
+	vreg_wlan: wlan-regulator {
+		compatible = "regulator-fixed";
+
+		regulator-name = "wl-reg";
+		regulator-min-microvolt = <2950000>;
+		regulator-max-microvolt = <2950000>;
+
+		gpio = <&tlmm 46 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&wlan_regulator_default_state>;
+	};
+};
+
+&adsp {
+	status = "okay";
+};
+
+&blsp1_i2c1 {
+	status = "okay";
+
+	fuel-gauge@55 {
+		compatible = "ti,bq27421";
+		reg = <0x55>;
+	};
 };
 
 &blsp1_i2c5 {
@@ -57,14 +94,30 @@
 	status = "okay";
 };
 
+&blsp1_uart4 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&blsp1_uart4_default_state>;
+
+	bluetooth {
+		compatible = "brcm,bcm43430a0-bt";
+
+		max-speed = <3000000>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&bluetooth_default_state>;
+
+		host-wakeup-gpios = <&tlmm 48 GPIO_ACTIVE_HIGH>;
+		device-wakeup-gpios = <&tlmm 47 GPIO_ACTIVE_HIGH>;
+		shutdown-gpios = <&tlmm 45 GPIO_ACTIVE_HIGH>;
+	};
+};
+
 &rpm_requests {
 	pm8226-regulators {
 		compatible = "qcom,rpm-pm8226-regulators";
 
-		pm8226_s1: s1 {
-			regulator-min-microvolt = <500000>;
-			regulator-max-microvolt = <1275000>;
-		};
 		pm8226_s3: s3 {
 			regulator-min-microvolt = <1200000>;
 			regulator-max-microvolt = <1350000>;
@@ -195,24 +248,55 @@
 
 	bus-width = <8>;
 	non-removable;
+};
 
-	pinctrl-names = "default";
-	pinctrl-0 = <&sdhc1_pin_a>;
+&sdhc_3 {
+	status = "okay";
+
+	max-frequency = <100000000>;
+	non-removable;
+
+	vmmc-supply = <&vreg_wlan>;
+	vqmmc-supply = <&pm8226_l6>;
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	wifi@1 {
+		compatible = "brcm,bcm43430a0-fmac", "brcm,bcm4329-fmac";
+		reg = <1>;
+
+		interrupts-extended = <&tlmm 37 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-names = "host-wake";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&wlan_hostwake_default_state>;
+	};
+};
+
+&smbb {
+	qcom,fast-charge-safe-current = <450000>;
+	qcom,fast-charge-current-limit = <400000>;
+	qcom,fast-charge-safe-voltage = <4350000>;
+	qcom,fast-charge-high-threshold-voltage = <4350000>;
+	qcom,auto-recharge-threshold-voltage = <4240000>;
+	qcom,minimum-input-voltage = <4450000>;
 };
 
 &tlmm {
-	sdhc1_pin_a: sdhc1-pin-active {
-		clk {
-			pins = "sdc1_clk";
-			drive-strength = <10>;
-			bias-disable;
-		};
+	blsp1_uart4_default_state: blsp1-uart4-default-state {
+		pins = "gpio12", "gpio13", "gpio14", "gpio15";
+		function = "blsp_uart4";
+		drive-strength = <8>;
+		bias-disable;
+	};
 
-		cmd-data {
-			pins = "sdc1_cmd", "sdc1_data";
-			drive-strength = <10>;
-			bias-pull-up;
-		};
+	bluetooth_default_state: bluetooth-default-state {
+		pins = "gpio47", "gpio48";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+		input-enable;
 	};
 
 	touch_pins: touch {
@@ -234,4 +318,31 @@
 			output-high;
 		};
 	};
+
+	wlan_hostwake_default_state: wlan-hostwake-default-state {
+		pins = "gpio37";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+		input-enable;
+	};
+
+	wlan_regulator_default_state: wlan-regulator-default-state {
+		pins = "gpio46";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-up;
+	};
+};
+
+&usb {
+	status = "okay";
+	extcon = <&smbb>;
+	dr_mode = "peripheral";
+};
+
+&usb_hs_phy {
+	extcon = <&smbb>;
+	v1p8-supply = <&pm8226_l10>;
+	v3p3-supply = <&pm8226_l20>;
 };
diff --git a/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts b/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts
index d664ccd454c5..573e4dc66bb0 100644
--- a/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts
+++ b/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts
@@ -1,6 +1,7 @@
 // SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
 #include <dt-bindings/pinctrl/qcom,pmic-mpp.h>
 #include "qcom-msm8660.dtsi"
@@ -83,7 +84,7 @@
 
 	soc {
 		pinctrl@800000 {
-			/* eMMMC pins, all 8 data lines connected */
+			/* eMMC pins, all 8 data lines connected */
 			dragon_sdcc1_pins: sdcc1 {
 				mux {
 					pins = "gpio159", "gpio160", "gpio161",
@@ -158,6 +159,19 @@
 				};
 			};
 
+			dragon_gsbi3_i2c_pins: gsbi3_i2c {
+				mux {
+					pins = "gpio43", "gpio44";
+					function = "gsbi3";
+				};
+				pinconf {
+					pins = "gpio43", "gpio44";
+					drive-strength = <8>;
+					/* These have external pull-up 2.2kOhm to 1.8V */
+					bias-disable;
+				};
+			};
+
 			dragon_gsbi8_i2c_pins: gsbi8_i2c {
 				mux {
 					pins = "gpio64", "gpio65";
@@ -239,6 +253,22 @@
 					bias-pull-up;
 				};
 			};
+
+			dragon_tma340_gpios: tma340 {
+				reset {
+					/* RESET line, TS_ATTN, WAKE_CTP */
+					pins = "gpio58";
+					function = "gpio";
+					drive-strength = <6>;
+					bias-disable;
+				};
+				irq {
+					pins = "gpio61"; /* IRQ line */
+					function = "gpio";
+					drive-strength = <2>;
+					bias-pull-up;
+				};
+			};
 		};
 
 		qcom,ssbi@500000 {
@@ -273,7 +303,7 @@
 				};
 
 				gpio@150 {
-					dragon_ethernet_gpios: ethernet-gpios {
+					dragon_ethernet_gpios: ethernet-state {
 						pinconf {
 							pins = "gpio7";
 							function = "normal";
@@ -282,7 +312,7 @@
 							power-source = <PM8058_GPIO_S3>;
 						};
 					};
-					dragon_bmp085_gpios: bmp085-gpios {
+					dragon_bmp085_gpios: bmp085-state {
 						pinconf {
 							pins = "gpio16";
 							function = "normal";
@@ -291,7 +321,7 @@
 							power-source = <PM8058_GPIO_S3>;
 						};
 					};
-					dragon_mpu3050_gpios: mpu3050-gpios {
+					dragon_mpu3050_gpios: mpu3050-state {
 						pinconf {
 							pins = "gpio17";
 							function = "normal";
@@ -300,7 +330,7 @@
 							power-source = <PM8058_GPIO_S3>;
 						};
 					};
-					dragon_sdcc3_gpios: sdcc3-gpios {
+					dragon_sdcc3_gpios: sdcc3-state {
 						pinconf {
 							pins = "gpio22";
 							function = "normal";
@@ -309,7 +339,7 @@
 							power-source = <PM8058_GPIO_S3>;
 						};
 					};
-					dragon_sdcc5_gpios: sdcc5-gpios {
+					dragon_sdcc5_gpios: sdcc5-state {
 						pinconf {
 							pins = "gpio26";
 							function = "normal";
@@ -319,7 +349,7 @@
 							power-source = <PM8058_GPIO_S3>;
 						};
 					};
-					dragon_ak8975_gpios: ak8975-gpios {
+					dragon_ak8975_gpios: ak8975-state {
 						pinconf {
 							pins = "gpio33";
 							function = "normal";
@@ -328,9 +358,9 @@
 							power-source = <PM8058_GPIO_S3>;
 						};
 					};
-					dragon_cm3605_gpios: cm3605-gpios {
+					dragon_cm3605_gpios: cm3605-state {
 						/* Pin 34 connected to the proxy IRQ */
-						pinconf_gpio34 {
+						gpio34-pins {
 							pins = "gpio34";
 							function = "normal";
 							input-enable;
@@ -338,7 +368,7 @@
 							power-source = <PM8058_GPIO_S3>;
 						};
 						/* Pin 35 connected to ASET */
-						pinconf_gpio35 {
+						gpio35-pins {
 							pins = "gpio35";
 							function = "normal";
 							output-high;
@@ -346,7 +376,7 @@
 							power-source = <PM8058_GPIO_S3>;
 						};
 					};
-					dragon_veth_gpios: veth-gpios {
+					dragon_veth_gpios: veth-state {
 						pinconf {
 							pins = "gpio40";
 							function = "normal";
@@ -416,6 +446,7 @@
 					compatible = "qcom,pm8058-led";
 					reg = <0x131>;
 					label = "pm8058:red";
+					color = <LED_COLOR_ID_RED>;
 					default-state = "off";
 				};
 				led@132 {
@@ -426,6 +457,7 @@
 					compatible = "qcom,pm8058-led";
 					reg = <0x132>;
 					label = "pm8058:yellow";
+					color = <LED_COLOR_ID_YELLOW>;
 					default-state = "off";
 					linux,default-trigger = "mmc0";
 				};
@@ -433,12 +465,53 @@
 					compatible = "qcom,pm8058-led";
 					reg = <0x133>;
 					label = "pm8058:green";
+					function = LED_FUNCTION_HEARTBEAT;
+					color = <LED_COLOR_ID_GREEN>;
 					default-state = "on";
 					linux,default-trigger = "heartbeat";
 				};
 			};
 		};
 
+		gsbi@16200000 {
+			qcom,mode = <GSBI_PROT_I2C>;
+			status = "okay";
+
+			gsbi3_i2c: i2c@16280000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&dragon_gsbi3_i2c_pins>;
+				status = "okay";
+
+				touchscreen@24 {
+					compatible = "cypress,cy8ctma340";
+					reg = <0x24>;
+					/* Certainly we can do at least 400 kHz */
+					clock-frequency = <400000>;
+					/* IRQ on GPIO61 called /CTP_INT */
+					interrupt-parent = <&tlmm>;
+					interrupts = <61 IRQ_TYPE_EDGE_FALLING>;
+					/*
+					 * The I2C bus is using a PCA9306 level translator from L16A
+					 * to L2B so these two voltages are needed and L16A is
+					 * kind of the IO voltage, however L16Aisn't really fed to
+					 * the TMA340, which relies entirely on L2B (PM8901 L2).
+					 */
+					vcpin-supply = <&pm8058_l16>;
+					vdd-supply = <&pm8901_l2>;
+					/* GPIO58, called WAKE_CTP */
+					reset-gpios = <&tlmm 58 GPIO_ACTIVE_LOW>;
+					touchscreen-size-x = <480>;
+					touchscreen-size-y = <800>;
+					active-interval-ms = <0>;
+					touch-timeout-ms = <255>;
+					lowpower-interval-ms = <10>;
+					bootloader-key = /bits/ 8 <0x00 0x01 0x02 0x03 0x04 0x05 0x06 0x07>;
+					pinctrl-names = "default";
+					pinctrl-0 = <&dragon_tma340_gpios>;
+				};
+			};
+		};
+
 		gsbi@19800000 {
 			status = "okay";
 			qcom,mode = <GSBI_PROT_I2C>;
@@ -629,7 +702,8 @@
 					bias-pull-down;
 				};
 				l2 {
-					regulator-min-microvolt = <2850000>;
+					/* TMA340 requires strictly 3.3V */
+					regulator-min-microvolt = <3300000>;
 					regulator-max-microvolt = <3300000>;
 					bias-pull-down;
 				};
@@ -674,14 +748,14 @@
 					bias-pull-down;
 				};
 
-				/* LVS0 thru 3 and mvs0 are just switches */
+				/* LVS0 thru 3 and mvs are just switches */
 				lvs0 {
 					regulator-always-on;
 				};
 				lvs1 { };
 				lvs2 { };
 				lvs3 { };
-				mvs0 {};
+				mvs { };
 
 			};
 
diff --git a/arch/arm/boot/dts/qcom-apq8064-asus-nexus7-flo.dts b/arch/arm/boot/dts/qcom-apq8064-asus-nexus7-flo.dts
index 9a835335bf78..fee278e32cb6 100644
--- a/arch/arm/boot/dts/qcom-apq8064-asus-nexus7-flo.dts
+++ b/arch/arm/boot/dts/qcom-apq8064-asus-nexus7-flo.dts
@@ -24,9 +24,9 @@
 		ramoops@88d00000{
 			compatible = "ramoops";
 			reg = <0x88d00000 0x100000>;
-			record-size     = <0x00020000>;
-			console-size    = <0x00020000>;
-			ftrace-size     = <0x00020000>;
+			record-size = <0x00020000>;
+			console-size = <0x00020000>;
+			ftrace-size = <0x00020000>;
 		};
 	};
 
@@ -44,12 +44,12 @@
 
 	gpio-keys {
 		compatible = "gpio-keys";
-		volume_up {
+		key-volume-up {
 			label = "Volume Up";
 			gpios = <&pm8921_gpio 4 GPIO_ACTIVE_HIGH>;
 			linux,code = <KEY_VOLUMEUP>;
 		};
-		volume_down {
+		key-volume-down {
 			label = "Volume Down";
 			gpios = <&pm8921_gpio 38 GPIO_ACTIVE_HIGH>;
 			linux,code = <KEY_VOLUMEDOWN>;
@@ -98,8 +98,8 @@
 				 * tabla2x-slim-VDDIO_CDC
 				 */
 				s4 {
-					regulator-min-microvolt	= <1800000>;
-					regulator-max-microvolt	= <1800000>;
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
 					qcom,switch-mode-frequency = <3200000>;
 					regulator-always-on;
 				};
@@ -212,13 +212,12 @@
 			};
 		};
 
-		dsi0: mdss_dsi@4700000 {
+		dsi0: dsi@4700000 {
 			status = "okay";
 			vdda-supply = <&pm8921_l2>;/*VDD_MIPI1 to 4*/
 			vdd-supply = <&pm8921_l8>;
 			vddio-supply = <&pm8921_lvs7>;
 			avdd-supply = <&pm8921_l11>;
-			vcss-supply = <&ext_3p3v>;
 
 			panel@0 {
 				reg = <0>;
@@ -342,17 +341,17 @@
 			};
 		};
 
-		imem@2a03f000 {
-			compatible = "syscon", "simple-mfd";
+		sram@2a03f000 {
+			compatible = "qcom,apq8064-imem", "syscon", "simple-mfd";
 			reg = <0x2a03f000 0x1000>;
 
 			reboot-mode {
 				compatible = "syscon-reboot-mode";
 				offset = <0x65c>;
 
-				mode-normal	= <0x77665501>;
-				mode-bootloader	= <0x77665500>;
-				mode-recovery	= <0x77665502>;
+				mode-normal = <0x77665501>;
+				mode-bootloader = <0x77665500>;
+				mode-recovery = <0x77665502>;
 			};
 		};
 	};
diff --git a/arch/arm/boot/dts/qcom-apq8064-cm-qs600.dts b/arch/arm/boot/dts/qcom-apq8064-cm-qs600.dts
index e068a8d0adf0..529629a0a9dc 100644
--- a/arch/arm/boot/dts/qcom-apq8064-cm-qs600.dts
+++ b/arch/arm/boot/dts/qcom-apq8064-cm-qs600.dts
@@ -82,8 +82,8 @@
 				};
 
 				s4 {
-					regulator-min-microvolt	= <1800000>;
-					regulator-max-microvolt	= <1800000>;
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
 					qcom,switch-mode-frequency = <3200000>;
 				};
 
@@ -196,8 +196,8 @@
 		qcom,ssbi@500000 {
 			pmic@0 {
 				gpio@150 {
-					wlan_default_gpios: wlan-gpios {
-						pios {
+					wlan_default_gpios: wlan-gpios-state {
+						pinconf {
 							pins = "gpio43";
 							function = "normal";
 							bias-disable;
@@ -215,7 +215,7 @@
 			vdda_refclk-supply = <&v3p3_fixed>;
 			pinctrl-0 = <&pcie_pins>;
 			pinctrl-names = "default";
-			perst-gpio = <&tlmm_pinmux 27 GPIO_ACTIVE_LOW>;
+			perst-gpios = <&tlmm_pinmux 27 GPIO_ACTIVE_LOW>;
 		};
 
 		amba {
@@ -230,9 +230,9 @@
 			sdcc3: mmc@12180000 {
 				status = "okay";
 				vmmc-supply = <&v3p3_fixed>;
-				pinctrl-names	= "default";
-				pinctrl-0	= <&card_detect>;
-				cd-gpios	= <&tlmm_pinmux 26 GPIO_ACTIVE_LOW>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&card_detect>;
+				cd-gpios = <&tlmm_pinmux 26 GPIO_ACTIVE_LOW>;
 			};
 			/* WLAN */
 			sdcc4: mmc@121c0000 {
diff --git a/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts b/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts
index 2638b380be20..a7f90217661b 100644
--- a/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts
+++ b/arch/arm/boot/dts/qcom-apq8064-ifc6410.dts
@@ -1,6 +1,7 @@
 // SPDX-License-Identifier: GPL-2.0
 #include "qcom-apq8064-v2.0.dtsi"
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
 
 / {
@@ -39,6 +40,7 @@
 
 		led@1 {
 			label = "apq8064:green:user1";
+			color = <LED_COLOR_ID_GREEN>;
 			gpios = <&pm8921_gpio 18 GPIO_ACTIVE_HIGH>;
 			default-state = "on";
 		};
@@ -108,8 +110,8 @@
 				};
 
 				s4 {
-					regulator-min-microvolt	= <1800000>;
-					regulator-max-microvolt	= <1800000>;
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
 					qcom,switch-mode-frequency = <3200000>;
 				};
 
@@ -240,8 +242,8 @@
 		};
 
 		sata0: sata@29000000 {
-			status		= "okay";
-			target-supply	= <&pm8921_s4>;
+			status = "okay";
+			target-supply = <&pm8921_s4>;
 		};
 
 		/* OTG */
@@ -285,14 +287,14 @@
 			vdda_refclk-supply = <&ext_3p3v>;
 			pinctrl-0 = <&pcie_pins>;
 			pinctrl-names = "default";
-			perst-gpio = <&tlmm_pinmux 27 GPIO_ACTIVE_LOW>;
+			perst-gpios = <&tlmm_pinmux 27 GPIO_ACTIVE_LOW>;
 		};
 
 		qcom,ssbi@500000 {
 			pmic@0 {
 				gpio@150 {
-					wlan_default_gpios: wlan-gpios {
-						pios {
+					wlan_default_gpios: wlan-gpios-state {
+						pinconf {
 							pins = "gpio43";
 							function = "normal";
 							bias-disable;
@@ -300,8 +302,8 @@
 						};
 					};
 
-					notify_led: nled {
-						pios {
+					notify_led: nled-state {
+						pinconf {
 							pins = "gpio18";
 							function = "normal";
 							bias-disable;
@@ -324,9 +326,9 @@
 			sdcc3: mmc@12180000 {
 				status = "okay";
 				vmmc-supply = <&pm8921_l6>;
-				pinctrl-names	= "default";
-				pinctrl-0	= <&card_detect>;
-				cd-gpios	= <&tlmm_pinmux 26 GPIO_ACTIVE_LOW>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&card_detect>;
+				cd-gpios = <&tlmm_pinmux 26 GPIO_ACTIVE_LOW>;
 			};
 			/* WLAN */
 			sdcc4: mmc@121c0000 {
@@ -341,7 +343,6 @@
 			status = "okay";
 
 			core-vdda-supply = <&pm8921_hdmi_switch>;
-			hdmi-mux-supply = <&ext_3p3v>;
 
 			hpd-gpios = <&tlmm_pinmux 72 GPIO_ACTIVE_HIGH>;
 
diff --git a/arch/arm/boot/dts/qcom-apq8064-pins.dtsi b/arch/arm/boot/dts/qcom-apq8064-pins.dtsi
index cbe42c4153a0..b4d286a6fab1 100644
--- a/arch/arm/boot/dts/qcom-apq8064-pins.dtsi
+++ b/arch/arm/boot/dts/qcom-apq8064-pins.dtsi
@@ -76,7 +76,7 @@
 		pinconf {
 			pins = "gpio20", "gpio21";
 			drive-strength = <2>;
-			bias-disable = <0>;
+			bias-disable;
 		};
 	};
 
@@ -116,7 +116,7 @@
 		pinconf {
 			pins = "gpio24", "gpio25";
 			drive-strength = <2>;
-			bias-disable = <0>;
+			bias-disable;
 		};
 	};
 
@@ -141,7 +141,7 @@
 		pinconf {
 			pins = "gpio8", "gpio9";
 			drive-strength = <2>;
-			bias-disable = <0>;
+			bias-disable;
 		};
 	};
 
@@ -166,7 +166,7 @@
 		pinconf {
 			pins = "gpio12", "gpio13";
 			drive-strength = <2>;
-			bias-disable = <0>;
+			bias-disable;
 		};
 	};
 
@@ -229,7 +229,7 @@
 		pinconf {
 			pins = "gpio16", "gpio17";
 			drive-strength = <2>;
-			bias-disable = <0>;
+			bias-disable;
 		};
 	};
 
@@ -282,7 +282,7 @@
 		pinconf {
 			pins = "gpio84", "gpio85";
 			drive-strength = <2>;
-			bias-disable = <0>;
+			bias-disable;
 		};
 	};
 
diff --git a/arch/arm/boot/dts/qcom-apq8064-sony-xperia-lagan-yuga.dts b/arch/arm/boot/dts/qcom-apq8064-sony-xperia-lagan-yuga.dts
new file mode 100644
index 000000000000..c07c5474750d
--- /dev/null
+++ b/arch/arm/boot/dts/qcom-apq8064-sony-xperia-lagan-yuga.dts
@@ -0,0 +1,401 @@
+// SPDX-License-Identifier: GPL-2.0
+#include "qcom-apq8064-v2.0.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/mfd/qcom-rpm.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+
+/ {
+	model = "Sony Xperia Z";
+	compatible = "sony,xperia-yuga", "qcom,apq8064";
+
+	aliases {
+		serial0 = &gsbi5_serial;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_keys_pin_a>;
+
+		key-camera-focus {
+			label = "camera_focus";
+			gpios = <&pm8921_gpio 3 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			linux,code = <KEY_CAMERA_FOCUS>;
+		};
+
+		key-camera-snapshot {
+			label = "camera_snapshot";
+			gpios = <&pm8921_gpio 4 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			linux,code = <KEY_CAMERA>;
+		};
+
+		key-volume-down {
+			label = "volume_down";
+			gpios = <&pm8921_gpio 29 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			linux,code = <KEY_VOLUMEDOWN>;
+		};
+
+		key-volume-up {
+			label = "volume_up";
+			gpios = <&pm8921_gpio 35 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			linux,code = <KEY_VOLUMEUP>;
+		};
+	};
+
+	soc {
+		pinctrl@800000 {
+			gsbi5_uart_pin_a: gsbi5-uart-pin-active {
+				rx {
+					pins = "gpio52";
+					function = "gsbi5";
+					drive-strength = <2>;
+					bias-pull-up;
+				};
+
+				tx {
+					pins = "gpio51";
+					function = "gsbi5";
+					drive-strength = <4>;
+					bias-disable;
+				};
+			};
+
+
+			sdcc3_cd_pin_a: sdcc3-cd-pin-active {
+				pins = "gpio26";
+				function = "gpio";
+
+				drive-strength = <2>;
+				bias-disable;
+			};
+		};
+
+
+		rpm@108000 {
+			regulators {
+				vin_l1_l2_l12_l18-supply = <&pm8921_s4>;
+				vin_lvs_1_3_6-supply = <&pm8921_s4>;
+				vin_lvs_4_5_7-supply = <&pm8921_s4>;
+				vin_ncp-supply = <&pm8921_l6>;
+				vin_lvs2-supply = <&pm8921_s4>;
+				vin_l24-supply = <&pm8921_s1>;
+				vin_l25-supply = <&pm8921_s1>;
+				vin_l27-supply = <&pm8921_s7>;
+				vin_l28-supply = <&pm8921_s7>;
+
+				/* Buck SMPS */
+				s1 {
+					regulator-always-on;
+					regulator-min-microvolt = <1225000>;
+					regulator-max-microvolt = <1225000>;
+					qcom,switch-mode-frequency = <3200000>;
+					bias-pull-down;
+				};
+
+				s2 {
+					regulator-min-microvolt = <1300000>;
+					regulator-max-microvolt = <1300000>;
+					qcom,switch-mode-frequency = <1600000>;
+					bias-pull-down;
+				};
+
+				s3 {
+					regulator-min-microvolt = <500000>;
+					regulator-max-microvolt = <1150000>;
+					qcom,switch-mode-frequency = <4800000>;
+					bias-pull-down;
+				};
+
+				s4 {
+					regulator-always-on;
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					qcom,switch-mode-frequency = <1600000>;
+					bias-pull-down;
+					qcom,force-mode = <QCOM_RPM_FORCE_MODE_AUTO>;
+				};
+
+				s7 {
+					regulator-min-microvolt = <1300000>;
+					regulator-max-microvolt = <1300000>;
+					qcom,switch-mode-frequency = <3200000>;
+				};
+
+				s8 {
+					regulator-min-microvolt = <2200000>;
+					regulator-max-microvolt = <2200000>;
+					qcom,switch-mode-frequency = <1600000>;
+				};
+
+				/* PMOS LDO */
+				l1 {
+					regulator-always-on;
+					regulator-min-microvolt = <1100000>;
+					regulator-max-microvolt = <1100000>;
+					bias-pull-down;
+				};
+
+				l2 {
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+					bias-pull-down;
+				};
+
+				l3 {
+					regulator-min-microvolt = <3075000>;
+					regulator-max-microvolt = <3075000>;
+					bias-pull-down;
+				};
+
+				l4 {
+					regulator-always-on;
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					bias-pull-down;
+				};
+
+				l5 {
+					regulator-min-microvolt = <2950000>;
+					regulator-max-microvolt = <2950000>;
+					bias-pull-down;
+				};
+
+				l6 {
+					regulator-min-microvolt = <2950000>;
+					regulator-max-microvolt = <2950000>;
+					bias-pull-down;
+				};
+
+				l7 {
+					regulator-min-microvolt = <1850000>;
+					regulator-max-microvolt = <2950000>;
+					bias-pull-down;
+				};
+
+				l8 {
+					regulator-min-microvolt = <2800000>;
+					regulator-max-microvolt = <2800000>;
+					bias-pull-down;
+				};
+
+				l9 {
+					regulator-min-microvolt = <3000000>;
+					regulator-max-microvolt = <3000000>;
+					bias-pull-down;
+				};
+
+				l10 {
+					regulator-min-microvolt = <2900000>;
+					regulator-max-microvolt = <2900000>;
+					bias-pull-down;
+				};
+
+				l11 {
+					regulator-min-microvolt = <3000000>;
+					regulator-max-microvolt = <3000000>;
+					bias-pull-down;
+				};
+
+				l12 {
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+					bias-pull-down;
+				};
+
+				l14 {
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					bias-pull-down;
+				};
+
+				l15 {
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <2950000>;
+					bias-pull-down;
+				};
+
+				l16 {
+					regulator-min-microvolt = <2800000>;
+					regulator-max-microvolt = <2800000>;
+					bias-pull-down;
+				};
+
+				l17 {
+					regulator-min-microvolt = <2000000>;
+					regulator-max-microvolt = <2000000>;
+					bias-pull-down;
+				};
+
+				l18 {
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+					bias-pull-down;
+				};
+
+				l21 {
+					regulator-min-microvolt = <1050000>;
+					regulator-max-microvolt = <1050000>;
+					bias-pull-down;
+				};
+
+				l22 {
+					regulator-min-microvolt = <2600000>;
+					regulator-max-microvolt = <2600000>;
+					bias-pull-down;
+				};
+
+				l23 {
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					bias-pull-down;
+				};
+
+				l24 {
+					regulator-min-microvolt = <750000>;
+					regulator-max-microvolt = <1150000>;
+					bias-pull-down;
+				};
+
+				l25 {
+					regulator-always-on;
+					regulator-min-microvolt = <1250000>;
+					regulator-max-microvolt = <1250000>;
+					bias-pull-down;
+				};
+
+				l27 {
+					regulator-min-microvolt = <1100000>;
+					regulator-max-microvolt = <1100000>;
+				};
+
+				l28 {
+					regulator-min-microvolt = <1050000>;
+					regulator-max-microvolt = <1050000>;
+					bias-pull-down;
+				};
+
+				l29 {
+					regulator-min-microvolt = <2000000>;
+					regulator-max-microvolt = <2000000>;
+					bias-pull-down;
+				};
+
+				/* Low Voltage Switch */
+				lvs1 {
+					bias-pull-down;
+				};
+
+				lvs2 {
+					bias-pull-down;
+				};
+
+				lvs3 {
+					bias-pull-down;
+				};
+
+				lvs4 {
+					bias-pull-down;
+				};
+
+				lvs5 {
+					bias-pull-down;
+				};
+
+				lvs6 {
+					bias-pull-down;
+				};
+
+				lvs7 {
+					bias-pull-down;
+				};
+
+				usb-switch {};
+
+				hdmi-switch {};
+
+				ncp {
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					qcom,switch-mode-frequency = <1600000>;
+				};
+			};
+		};
+
+		qcom,ssbi@500000 {
+			pmic@0 {
+				gpio@150 {
+					gpio_keys_pin_a: gpio-keys-active-state {
+						pins = "gpio3", "gpio4", "gpio29", "gpio35";
+						function = "normal";
+
+						bias-pull-up;
+						drive-push-pull;
+						input-enable;
+						power-source = <2>;
+						qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
+						qcom,pull-up-strength = <0>;
+					};
+				};
+			};
+		};
+
+		usb@12500000 {
+			status = "okay";
+			dr_mode = "otg";
+			ulpi {
+				phy {
+					v3p3-supply = <&pm8921_l3>;
+					v1p8-supply = <&pm8921_l4>;
+				};
+			};
+		};
+
+		gsbi@1a200000 {
+			status = "okay";
+			qcom,mode = <GSBI_PROT_I2C_UART>;
+
+			serial@1a240000 {
+				status = "okay";
+
+				pinctrl-names = "default";
+				pinctrl-0 = <&gsbi5_uart_pin_a>;
+			};
+		};
+
+		amba {
+			sdcc1: mmc@12400000 {
+				status = "okay";
+
+				vmmc-supply = <&pm8921_l5>;
+				vqmmc-supply = <&pm8921_s4>;
+			};
+
+			sdcc3: mmc@12180000 {
+				status = "okay";
+
+				vmmc-supply = <&pm8921_l6>;
+				cd-gpios = <&tlmm_pinmux 26 GPIO_ACTIVE_LOW>;
+
+				pinctrl-names = "default";
+				pinctrl-0 = <&sdcc3_pins>, <&sdcc3_cd_pin_a>;
+			};
+		};
+
+		riva-pil@3204000 {
+			status = "okay";
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&riva_wlan_pin_a>, <&riva_bt_pin_a>, <&riva_fm_pin_a>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/qcom-apq8064-sony-xperia-yuga.dts b/arch/arm/boot/dts/qcom-apq8064-sony-xperia-yuga.dts
deleted file mode 100644
index f8c97efc61fc..000000000000
--- a/arch/arm/boot/dts/qcom-apq8064-sony-xperia-yuga.dts
+++ /dev/null
@@ -1,402 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-#include "qcom-apq8064-v2.0.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/mfd/qcom-rpm.h>
-#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
-
-/ {
-	model = "Sony Xperia Z";
-	compatible = "sony,xperia-yuga", "qcom,apq8064";
-
-	aliases {
-		serial0 = &gsbi5_serial;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	gpio-keys {
-		compatible = "gpio-keys";
-		input-name = "gpio-keys";
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&gpio_keys_pin_a>;
-
-		camera-focus {
-			label = "camera_focus";
-			gpios = <&pm8921_gpio 3 GPIO_ACTIVE_LOW>;
-			linux,input-type = <1>;
-			linux,code = <KEY_CAMERA_FOCUS>;
-		};
-
-		camera-snapshot {
-			label = "camera_snapshot";
-			gpios = <&pm8921_gpio 4 GPIO_ACTIVE_LOW>;
-			linux,input-type = <1>;
-			linux,code = <KEY_CAMERA>;
-		};
-
-		volume-down {
-			label = "volume_down";
-			gpios = <&pm8921_gpio 29 GPIO_ACTIVE_LOW>;
-			linux,input-type = <1>;
-			linux,code = <KEY_VOLUMEDOWN>;
-		};
-
-		volume-up {
-			label = "volume_up";
-			gpios = <&pm8921_gpio 35 GPIO_ACTIVE_LOW>;
-			linux,input-type = <1>;
-			linux,code = <KEY_VOLUMEUP>;
-		};
-	};
-
-	soc {
-		pinctrl@800000 {
-			gsbi5_uart_pin_a: gsbi5-uart-pin-active {
-				rx {
-					pins = "gpio52";
-					function = "gsbi5";
-					drive-strength = <2>;
-					bias-pull-up;
-				};
-
-				tx {
-					pins = "gpio51";
-					function = "gsbi5";
-					drive-strength = <4>;
-					bias-disable;
-				};
-			};
-
-
-			sdcc3_cd_pin_a: sdcc3-cd-pin-active {
-				pins = "gpio26";
-				function = "gpio";
-
-				drive-strength = <2>;
-				bias-disable;
-			};
-		};
-
-
-		rpm@108000 {
-			regulators {
-				vin_l1_l2_l12_l18-supply = <&pm8921_s4>;
-				vin_lvs_1_3_6-supply = <&pm8921_s4>;
-				vin_lvs_4_5_7-supply = <&pm8921_s4>;
-				vin_ncp-supply = <&pm8921_l6>;
-				vin_lvs2-supply = <&pm8921_s4>;
-				vin_l24-supply = <&pm8921_s1>;
-				vin_l25-supply = <&pm8921_s1>;
-				vin_l27-supply = <&pm8921_s7>;
-				vin_l28-supply = <&pm8921_s7>;
-
-				/* Buck SMPS */
-				s1 {
-					regulator-always-on;
-					regulator-min-microvolt = <1225000>;
-					regulator-max-microvolt = <1225000>;
-					qcom,switch-mode-frequency = <3200000>;
-					bias-pull-down;
-				};
-
-				s2 {
-					regulator-min-microvolt = <1300000>;
-					regulator-max-microvolt = <1300000>;
-					qcom,switch-mode-frequency = <1600000>;
-					bias-pull-down;
-				};
-
-				s3 {
-					regulator-min-microvolt = <500000>;
-					regulator-max-microvolt = <1150000>;
-					qcom,switch-mode-frequency = <4800000>;
-					bias-pull-down;
-				};
-
-				s4 {
-					regulator-always-on;
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					qcom,switch-mode-frequency = <1600000>;
-					bias-pull-down;
-					qcom,force-mode = <QCOM_RPM_FORCE_MODE_AUTO>;
-				};
-
-				s7 {
-					regulator-min-microvolt = <1300000>;
-					regulator-max-microvolt = <1300000>;
-					qcom,switch-mode-frequency = <3200000>;
-				};
-
-				s8 {
-					regulator-min-microvolt = <2200000>;
-					regulator-max-microvolt = <2200000>;
-					qcom,switch-mode-frequency = <1600000>;
-				};
-
-				/* PMOS LDO */
-				l1 {
-					regulator-always-on;
-					regulator-min-microvolt = <1100000>;
-					regulator-max-microvolt = <1100000>;
-					bias-pull-down;
-				};
-
-				l2 {
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <1200000>;
-					bias-pull-down;
-				};
-
-				l3 {
-					regulator-min-microvolt = <3075000>;
-					regulator-max-microvolt = <3075000>;
-					bias-pull-down;
-				};
-
-				l4 {
-					regulator-always-on;
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					bias-pull-down;
-				};
-
-				l5 {
-					regulator-min-microvolt = <2950000>;
-					regulator-max-microvolt = <2950000>;
-					bias-pull-down;
-				};
-
-				l6 {
-					regulator-min-microvolt = <2950000>;
-					regulator-max-microvolt = <2950000>;
-					bias-pull-down;
-				};
-
-				l7 {
-					regulator-min-microvolt = <1850000>;
-					regulator-max-microvolt = <2950000>;
-					bias-pull-down;
-				};
-
-				l8 {
-					regulator-min-microvolt = <2800000>;
-					regulator-max-microvolt = <2800000>;
-					bias-pull-down;
-				};
-
-				l9 {
-					regulator-min-microvolt = <3000000>;
-					regulator-max-microvolt = <3000000>;
-					bias-pull-down;
-				};
-
-				l10 {
-					regulator-min-microvolt = <2900000>;
-					regulator-max-microvolt = <2900000>;
-					bias-pull-down;
-				};
-
-				l11 {
-					regulator-min-microvolt = <3000000>;
-					regulator-max-microvolt = <3000000>;
-					bias-pull-down;
-				};
-
-				l12 {
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <1200000>;
-					bias-pull-down;
-				};
-
-				l14 {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					bias-pull-down;
-				};
-
-				l15 {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <2950000>;
-					bias-pull-down;
-				};
-
-				l16 {
-					regulator-min-microvolt = <2800000>;
-					regulator-max-microvolt = <2800000>;
-					bias-pull-down;
-				};
-
-				l17 {
-					regulator-min-microvolt = <2000000>;
-					regulator-max-microvolt = <2000000>;
-					bias-pull-down;
-				};
-
-				l18 {
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <1200000>;
-					bias-pull-down;
-				};
-
-				l21 {
-					regulator-min-microvolt = <1050000>;
-					regulator-max-microvolt = <1050000>;
-					bias-pull-down;
-				};
-
-				l22 {
-					regulator-min-microvolt = <2600000>;
-					regulator-max-microvolt = <2600000>;
-					bias-pull-down;
-				};
-
-				l23 {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					bias-pull-down;
-				};
-
-				l24 {
-					regulator-min-microvolt = <750000>;
-					regulator-max-microvolt = <1150000>;
-					bias-pull-down;
-				};
-
-				l25 {
-					regulator-always-on;
-					regulator-min-microvolt = <1250000>;
-					regulator-max-microvolt = <1250000>;
-					bias-pull-down;
-				};
-
-				l27 {
-					regulator-min-microvolt = <1100000>;
-					regulator-max-microvolt = <1100000>;
-				};
-
-				l28 {
-					regulator-min-microvolt = <1050000>;
-					regulator-max-microvolt = <1050000>;
-					bias-pull-down;
-				};
-
-				l29 {
-					regulator-min-microvolt = <2000000>;
-					regulator-max-microvolt = <2000000>;
-					bias-pull-down;
-				};
-
-				/* Low Voltage Switch */
-				lvs1 {
-					bias-pull-down;
-				};
-
-				lvs2 {
-					bias-pull-down;
-				};
-
-				lvs3 {
-					bias-pull-down;
-				};
-
-				lvs4 {
-					bias-pull-down;
-				};
-
-				lvs5 {
-					bias-pull-down;
-				};
-
-				lvs6 {
-					bias-pull-down;
-				};
-
-				lvs7 {
-					bias-pull-down;
-				};
-
-				usb-switch {};
-
-				hdmi-switch {};
-
-				ncp {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					qcom,switch-mode-frequency = <1600000>;
-				};
-			};
-		};
-
-		qcom,ssbi@500000 {
-			pmic@0 {
-				gpio@150 {
-					gpio_keys_pin_a: gpio-keys-pin-active {
-						pins = "gpio3", "gpio4", "gpio29", "gpio35";
-						function = "normal";
-
-						bias-pull-up;
-						drive-push-pull;
-						input-enable;
-						power-source = <2>;
-						qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
-						qcom,pull-up-strength = <0>;
-					};
-				};
-			};
-		};
-
-		usb@12500000 {
-			status = "okay";
-			dr_mode = "otg";
-			ulpi {
-				phy {
-					v3p3-supply = <&pm8921_l3>;
-					v1p8-supply = <&pm8921_l4>;
-				};
-			};
-		};
-
-		gsbi@1a200000 {
-			status = "okay";
-			qcom,mode = <GSBI_PROT_I2C_UART>;
-
-			serial@1a240000 {
-				status = "okay";
-
-				pinctrl-names = "default";
-				pinctrl-0 = <&gsbi5_uart_pin_a>;
-			};
-		};
-
-		amba {
-			sdcc1: mmc@12400000 {
-				status = "okay";
-
-				vmmc-supply = <&pm8921_l5>;
-				vqmmc-supply = <&pm8921_s4>;
-			};
-
-			sdcc3: mmc@12180000 {
-				status = "okay";
-
-				vmmc-supply = <&pm8921_l6>;
-				cd-gpios = <&tlmm_pinmux 26 GPIO_ACTIVE_LOW>;
-
-				pinctrl-names = "default";
-				pinctrl-0 = <&sdcc3_pins>, <&sdcc3_cd_pin_a>;
-			};
-		};
-
-		riva-pil@3204000 {
-			status = "okay";
-
-			pinctrl-names = "default";
-			pinctrl-0 = <&riva_wlan_pin_a>, <&riva_bt_pin_a>, <&riva_fm_pin_a>;
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/qcom-apq8064.dtsi b/arch/arm/boot/dts/qcom-apq8064.dtsi
index 4d562c94c31c..942aa2278355 100644
--- a/arch/arm/boot/dts/qcom-apq8064.dtsi
+++ b/arch/arm/boot/dts/qcom-apq8064.dtsi
@@ -2,6 +2,7 @@
 /dts-v1/;
 
 #include <dt-bindings/clock/qcom,gcc-msm8960.h>
+#include <dt-bindings/clock/qcom,lcc-msm8960.h>
 #include <dt-bindings/reset/qcom,gcc-msm8960.h>
 #include <dt-bindings/clock/qcom,mmcc-msm8960.h>
 #include <dt-bindings/clock/qcom,rpmcc.h>
@@ -105,7 +106,7 @@
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 
-			thermal-sensors = <&gcc 7>;
+			thermal-sensors = <&tsens 7>;
 			coefficients = <1199 0>;
 
 			trips {
@@ -126,7 +127,7 @@
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 
-			thermal-sensors = <&gcc 8>;
+			thermal-sensors = <&tsens 8>;
 			coefficients = <1132 0>;
 
 			trips {
@@ -147,7 +148,7 @@
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 
-			thermal-sensors = <&gcc 9>;
+			thermal-sensors = <&tsens 9>;
 			coefficients = <1199 0>;
 
 			trips {
@@ -168,7 +169,7 @@
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 
-			thermal-sensors = <&gcc 10>;
+			thermal-sensors = <&tsens 10>;
 			coefficients = <1132 0>;
 
 			trips {
@@ -227,7 +228,7 @@
 	smd {
 		compatible = "qcom,smd";
 
-		modem@0 {
+		modem-edge {
 			interrupts = <0 37 IRQ_TYPE_EDGE_RISING>;
 
 			qcom,ipc = <&l2cc 8 3>;
@@ -236,7 +237,7 @@
 			status = "disabled";
 		};
 
-		q6@1 {
+		q6-edge {
 			interrupts = <0 90 IRQ_TYPE_EDGE_RISING>;
 
 			qcom,ipc = <&l2cc 8 15>;
@@ -245,7 +246,7 @@
 			status = "disabled";
 		};
 
-		dsps@3 {
+		dsps-edge {
 			interrupts = <0 138 IRQ_TYPE_EDGE_RISING>;
 
 			qcom,ipc = <&sps_sic_non_secure 0x4080 0>;
@@ -254,7 +255,7 @@
 			status = "disabled";
 		};
 
-		riva@6 {
+		riva-edge {
 			interrupts = <0 198 IRQ_TYPE_EDGE_RISING>;
 
 			qcom,ipc = <&l2cc 8 25>;
@@ -315,7 +316,7 @@
 
 	firmware {
 		scm {
-			compatible = "qcom,scm-apq8064";
+			compatible = "qcom,scm-apq8064", "qcom,scm";
 
 			clocks = <&rpmcc RPM_DAYTONA_FABRIC_CLK>;
 			clock-names = "core";
@@ -430,8 +431,8 @@
 		};
 
 		sps_sic_non_secure: sps-sic-non-secure@12100000 {
-			compatible	= "syscon";
-			reg		= <0x12100000 0x10000>;
+			compatible = "syscon";
+			reg = <0x12100000 0x10000>;
 		};
 
 		gsbi1: gsbi@12440000 {
@@ -796,27 +797,41 @@
 		};
 
 		qfprom: qfprom@700000 {
-			compatible	= "qcom,qfprom";
-			reg		= <0x00700000 0x1000>;
-			#address-cells	= <1>;
-			#size-cells	= <1>;
+			compatible = "qcom,apq8064-qfprom", "qcom,qfprom";
+			reg = <0x00700000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
 			ranges;
-			tsens_calib: calib {
+			tsens_calib: calib@404 {
 				reg = <0x404 0x10>;
 			};
-			tsens_backup: backup_calib {
+			tsens_backup: backup_calib@414 {
 				reg = <0x414 0x10>;
 			};
 		};
 
 		gcc: clock-controller@900000 {
-			compatible = "qcom,gcc-apq8064";
+			compatible = "qcom,gcc-apq8064", "syscon";
 			reg = <0x00900000 0x4000>;
-			nvmem-cells = <&tsens_calib>, <&tsens_backup>;
-			nvmem-cell-names = "calib", "calib_backup";
 			#clock-cells = <1>;
+			#power-domain-cells = <1>;
 			#reset-cells = <1>;
-			#thermal-sensor-cells = <1>;
+			clocks = <&cxo_board>,
+				 <&pxo_board>,
+				 <&lcc PLL4>;
+			clock-names = "cxo", "pxo", "pll4";
+
+			tsens: thermal-sensor {
+				compatible = "qcom,msm8960-tsens";
+
+				nvmem-cells = <&tsens_calib>, <&tsens_backup>;
+				nvmem-cell-names = "calib", "calib_backup";
+				interrupts = <GIC_SPI 178 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "uplow";
+
+				#qcom,sensors = <11>;
+				#thermal-sensor-cells = <1>;
+			};
 		};
 
 		lcc: clock-controller@28000000 {
@@ -824,33 +839,66 @@
 			reg = <0x28000000 0x1000>;
 			#clock-cells = <1>;
 			#reset-cells = <1>;
+			clocks = <&pxo_board>,
+				 <&gcc PLL4_VOTE>,
+				 <0>,
+				 <0>, <0>,
+				 <0>, <0>,
+				 <0>;
+			clock-names = "pxo",
+				      "pll4_vote",
+				      "mi2s_codec_clk",
+				      "codec_i2s_mic_codec_clk",
+				      "spare_i2s_mic_codec_clk",
+				      "codec_i2s_spkr_codec_clk",
+				      "spare_i2s_spkr_codec_clk",
+				      "pcm_codec_clk";
 		};
 
 		mmcc: clock-controller@4000000 {
 			compatible = "qcom,mmcc-apq8064";
 			reg = <0x4000000 0x1000>;
 			#clock-cells = <1>;
+			#power-domain-cells = <1>;
 			#reset-cells = <1>;
+			clocks = <&pxo_board>,
+				 <&gcc PLL3>,
+				 <&gcc PLL8_VOTE>,
+				 <&dsi0_phy 1>,
+				 <&dsi0_phy 0>,
+				 <0>,
+				 <0>,
+				 <0>;
+			clock-names = "pxo",
+				      "pll3",
+				      "pll8_vote",
+				      "dsi1pll",
+				      "dsi1pllbyte",
+				      "dsi2pll",
+				      "dsi2pllbyte",
+				      "hdmipll";
 		};
 
 		l2cc: clock-controller@2011000 {
-			compatible	= "syscon";
-			reg		= <0x2011000 0x1000>;
+			compatible = "qcom,kpss-gcc", "syscon";
+			reg = <0x2011000 0x1000>;
 		};
 
 		rpm@108000 {
-			compatible	= "qcom,rpm-apq8064";
-			reg		= <0x108000 0x1000>;
-			qcom,ipc	= <&l2cc 0x8 2>;
+			compatible = "qcom,rpm-apq8064";
+			reg = <0x108000 0x1000>;
+			qcom,ipc = <&l2cc 0x8 2>;
 
-			interrupts	= <GIC_SPI 19 IRQ_TYPE_EDGE_RISING>,
-					  <GIC_SPI 21 IRQ_TYPE_EDGE_RISING>,
-					  <GIC_SPI 22 IRQ_TYPE_EDGE_RISING>;
-			interrupt-names	= "ack", "err", "wakeup";
+			interrupts = <GIC_SPI 19 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 21 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 22 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "ack", "err", "wakeup";
 
 			rpmcc: clock-controller {
-				compatible	= "qcom,rpmcc-apq8064", "qcom,rpmcc";
+				compatible = "qcom,rpmcc-apq8064", "qcom,rpmcc";
 				#clock-cells = <1>;
+				clocks = <&pxo_board>, <&cxo_board>;
+				clock-names = "pxo", "cxo";
 			};
 
 			regulators {
@@ -1002,43 +1050,43 @@
 		};
 
 		sata_phy0: phy@1b400000 {
-			compatible	= "qcom,apq8064-sata-phy";
-			status		= "disabled";
-			reg		= <0x1b400000 0x200>;
-			reg-names	= "phy_mem";
-			clocks		= <&gcc SATA_PHY_CFG_CLK>;
-			clock-names	= "cfg";
-			#phy-cells	= <0>;
+			compatible = "qcom,apq8064-sata-phy";
+			status = "disabled";
+			reg = <0x1b400000 0x200>;
+			reg-names = "phy_mem";
+			clocks = <&gcc SATA_PHY_CFG_CLK>;
+			clock-names = "cfg";
+			#phy-cells = <0>;
 		};
 
 		sata0: sata@29000000 {
-			compatible		= "qcom,apq8064-ahci", "generic-ahci";
-			status			= "disabled";
-			reg			= <0x29000000 0x180>;
-			interrupts		= <GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH>;
-
-			clocks			= <&gcc SFAB_SATA_S_H_CLK>,
-						<&gcc SATA_H_CLK>,
-						<&gcc SATA_A_CLK>,
-						<&gcc SATA_RXOOB_CLK>,
-						<&gcc SATA_PMALIVE_CLK>;
-			clock-names		= "slave_iface",
-						"iface",
-						"bus",
-						"rxoob",
-						"core_pmalive";
-
-			assigned-clocks		= <&gcc SATA_RXOOB_CLK>,
-						<&gcc SATA_PMALIVE_CLK>;
-			assigned-clock-rates	= <100000000>, <100000000>;
-
-			phys			= <&sata_phy0>;
-			phy-names		= "sata-phy";
-			ports-implemented	= <0x1>;
+			compatible = "qcom,apq8064-ahci", "generic-ahci";
+			status	 = "disabled";
+			reg	 = <0x29000000 0x180>;
+			interrupts = <GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH>;
+
+			clocks = <&gcc SFAB_SATA_S_H_CLK>,
+				 <&gcc SATA_H_CLK>,
+				 <&gcc SATA_A_CLK>,
+				 <&gcc SATA_RXOOB_CLK>,
+				 <&gcc SATA_PMALIVE_CLK>;
+			clock-names = "slave_iface",
+				      "iface",
+				      "bus",
+				      "rxoob",
+				      "core_pmalive";
+
+			assigned-clocks = <&gcc SATA_RXOOB_CLK>,
+					  <&gcc SATA_PMALIVE_CLK>;
+			assigned-clock-rates = <100000000>, <100000000>;
+
+			phys = <&sata_phy0>;
+			phy-names = "sata-phy";
+			ports-implemented = <0x1>;
 		};
 
 		/* Temporary fixed regulator */
-		sdcc1bam:dma@12402000{
+		sdcc1bam: dma-controller@12402000{
 			compatible = "qcom,bam-v1.3.0";
 			reg = <0x12402000 0x8000>;
 			interrupts = <0 98 IRQ_TYPE_LEVEL_HIGH>;
@@ -1048,7 +1096,7 @@
 			qcom,ee = <0>;
 		};
 
-		sdcc3bam:dma@12182000{
+		sdcc3bam: dma-controller@12182000{
 			compatible = "qcom,bam-v1.3.0";
 			reg = <0x12182000 0x8000>;
 			interrupts = <0 96 IRQ_TYPE_LEVEL_HIGH>;
@@ -1058,7 +1106,7 @@
 			qcom,ee = <0>;
 		};
 
-		sdcc4bam:dma@121c2000{
+		sdcc4bam: dma-controller@121c2000{
 			compatible = "qcom,bam-v1.3.0";
 			reg = <0x121c2000 0x8000>;
 			interrupts = <0 95 IRQ_TYPE_LEVEL_HIGH>;
@@ -1074,18 +1122,18 @@
 			#size-cells = <1>;
 			ranges;
 			sdcc1: mmc@12400000 {
-				status		= "disabled";
-				compatible	= "arm,pl18x", "arm,primecell";
-				pinctrl-names	= "default";
-				pinctrl-0	= <&sdcc1_pins>;
+				status = "disabled";
+				compatible = "arm,pl18x", "arm,primecell";
+				pinctrl-names = "default";
+				pinctrl-0 = <&sdcc1_pins>;
 				arm,primecell-periphid = <0x00051180>;
-				reg		= <0x12400000 0x2000>;
-				interrupts	= <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
-				interrupt-names	= "cmd_irq";
-				clocks		= <&gcc SDC1_CLK>, <&gcc SDC1_H_CLK>;
-				clock-names	= "mclk", "apb_pclk";
-				bus-width	= <8>;
-				max-frequency	= <96000000>;
+				reg = <0x12400000 0x2000>;
+				interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "cmd_irq";
+				clocks = <&gcc SDC1_CLK>, <&gcc SDC1_H_CLK>;
+				clock-names = "mclk", "apb_pclk";
+				bus-width = <8>;
+				max-frequency = <96000000>;
 				non-removable;
 				cap-sd-highspeed;
 				cap-mmc-highspeed;
@@ -1094,36 +1142,36 @@
 			};
 
 			sdcc3: mmc@12180000 {
-				compatible	= "arm,pl18x", "arm,primecell";
+				compatible = "arm,pl18x", "arm,primecell";
 				arm,primecell-periphid = <0x00051180>;
-				status		= "disabled";
-				reg		= <0x12180000 0x2000>;
-				interrupts	= <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
-				interrupt-names	= "cmd_irq";
-				clocks		= <&gcc SDC3_CLK>, <&gcc SDC3_H_CLK>;
-				clock-names	= "mclk", "apb_pclk";
-				bus-width	= <4>;
+				status = "disabled";
+				reg = <0x12180000 0x2000>;
+				interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "cmd_irq";
+				clocks = <&gcc SDC3_CLK>, <&gcc SDC3_H_CLK>;
+				clock-names = "mclk", "apb_pclk";
+				bus-width = <4>;
 				cap-sd-highspeed;
 				cap-mmc-highspeed;
-				max-frequency	= <192000000>;
+				max-frequency = <192000000>;
 				no-1-8-v;
 				dmas = <&sdcc3bam 2>, <&sdcc3bam 1>;
 				dma-names = "tx", "rx";
 			};
 
 			sdcc4: mmc@121c0000 {
-				compatible	= "arm,pl18x", "arm,primecell";
+				compatible = "arm,pl18x", "arm,primecell";
 				arm,primecell-periphid = <0x00051180>;
-				status		= "disabled";
-				reg		= <0x121c0000 0x2000>;
-				interrupts	= <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
-				interrupt-names	= "cmd_irq";
-				clocks		= <&gcc SDC4_CLK>, <&gcc SDC4_H_CLK>;
-				clock-names	= "mclk", "apb_pclk";
-				bus-width	= <4>;
+				status = "disabled";
+				reg = <0x121c0000 0x2000>;
+				interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "cmd_irq";
+				clocks = <&gcc SDC4_CLK>, <&gcc SDC4_H_CLK>;
+				clock-names = "mclk", "apb_pclk";
+				bus-width = <4>;
 				cap-sd-highspeed;
 				cap-mmc-highspeed;
-				max-frequency	= <48000000>;
+				max-frequency = <48000000>;
 				dmas = <&sdcc4bam 2>, <&sdcc4bam 1>;
 				dma-names = "tx", "rx";
 				pinctrl-names = "default";
@@ -1238,7 +1286,7 @@
 			reg = <0x5700000 0x70>;
 		};
 
-		dsi0: mdss_dsi@4700000 {
+		dsi0: dsi@4700000 {
 			compatible = "qcom,mdss-dsi-ctrl";
 			label = "MDSS DSI CTRL->0";
 			#address-cells = <1>;
@@ -1268,6 +1316,9 @@
 						<&dsi0_phy 1>;
 			syscon-sfpb = <&mmss_sfpb>;
 			phys = <&dsi0_phy>;
+			phy-names = "dsi";
+			status = "disabled";
+
 			ports {
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -1296,9 +1347,10 @@
 				<0x04700300 0x200>,
 				<0x04700500 0x5c>;
 			reg-names = "dsi_pll", "dsi_phy", "dsi_phy_regulator";
-			clock-names = "iface_clk", "ref";
+			clock-names = "iface", "ref";
 			clocks = <&mmcc DSI_M_AHB_CLK>,
 				 <&pxo_board>;
+			status = "disabled";
 		};
 
 
@@ -1367,11 +1419,11 @@
 		};
 
 		pcie: pci@1b500000 {
-			compatible = "qcom,pcie-apq8064", "snps,dw-pcie";
-			reg = <0x1b500000 0x1000
-			       0x1b502000 0x80
-			       0x1b600000 0x100
-			       0x0ff00000 0x100000>;
+			compatible = "qcom,pcie-apq8064";
+			reg = <0x1b500000 0x1000>,
+			      <0x1b502000 0x80>,
+			      <0x1b600000 0x100>,
+			      <0x0ff00000 0x100000>;
 			reg-names = "dbi", "elbi", "parf", "config";
 			device_type = "pci";
 			linux,pci-domain = <0>;
@@ -1379,8 +1431,8 @@
 			num-lanes = <1>;
 			#address-cells = <3>;
 			#size-cells = <2>;
-			ranges = <0x81000000 0 0 0x0fe00000 0 0x00100000   /* I/O */
-				  0x82000000 0 0x08000000 0x08000000 0 0x07e00000>; /* memory */
+			ranges = <0x81000000 0 0          0x0fe00000 0 0x00100000>, /* I/O */
+				 <0x82000000 0 0x08000000 0x08000000 0 0x07e00000>; /* mem */
 			interrupts = <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "msi";
 			#interrupt-cells = <1>;
@@ -1417,7 +1469,6 @@
 				      "slave_iface";
 
 			phys = <&hdmi_phy>;
-			phy-names = "hdmi-phy";
 
 			ports {
 				#address-cells = <1>;
@@ -1545,7 +1596,7 @@
 
 					qcom,mmio = <&riva>;
 
-					bt {
+					bluetooth {
 						compatible = "qcom,wcnss-bt";
 					};
 
diff --git a/arch/arm/boot/dts/qcom-apq8074-dragonboard.dts b/arch/arm/boot/dts/qcom-apq8074-dragonboard.dts
index 83793b835d40..91716298ec5e 100644
--- a/arch/arm/boot/dts/qcom-apq8074-dragonboard.dts
+++ b/arch/arm/boot/dts/qcom-apq8074-dragonboard.dts
@@ -1,4 +1,5 @@
 // SPDX-License-Identifier: GPL-2.0
+#include <dt-bindings/gpio/gpio.h>
 #include "qcom-msm8974.dtsi"
 #include "qcom-pm8841.dtsi"
 #include "qcom-pm8941.dtsi"
@@ -16,331 +17,293 @@
 	chosen {
 		stdout-path = "serial0:115200n8";
 	};
+};
+
+&blsp1_uart2 {
+	status = "okay";
+};
 
-	soc {
-		serial@f991e000 {
+&blsp2_i2c5 {
+	status = "okay";
+	clock-frequency = <200000>;
+
+	eeprom: eeprom@52 {
+		compatible = "atmel,24c128";
+		reg = <0x52>;
+		pagesize = <32>;
+		read-only;
+	};
+};
+
+&otg {
+	status = "okay";
+
+	phys = <&usb_hs2_phy>;
+	phy-select = <&tcsr 0xb000 1>;
+	extcon = <&smbb>, <&usb_id>;
+	vbus-supply = <&chg_otg>;
+	hnp-disable;
+	srp-disable;
+	adp-disable;
+
+	ulpi {
+		phy@b {
 			status = "okay";
+			v3p3-supply = <&pm8941_l24>;
+			v1p8-supply = <&pm8941_l6>;
+			extcon = <&smbb>;
+			qcom,init-seq = /bits/ 8 <0x1 0x63>;
+		};
+	};
+};
+
+&rpm_requests {
+	pm8841-regulators {
+		compatible = "qcom,rpm-pm8841-regulators";
+
+		pm8841_s1: s1 {
+			regulator-min-microvolt = <675000>;
+			regulator-max-microvolt = <1050000>;
 		};
 
-		sdhci@f9824900 {
-			bus-width = <8>;
-			non-removable;
-			status = "okay";
+		pm8841_s2: s2 {
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1050000>;
+		};
 
-			vmmc-supply = <&pm8941_l20>;
-			vqmmc-supply = <&pm8941_s3>;
+		pm8841_s3: s3 {
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1050000>;
+		};
 
-			pinctrl-names = "default";
-			pinctrl-0 = <&sdhc1_pin_a>;
+		pm8841_s4: s4 {
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1050000>;
 		};
+	};
 
-		sdhci@f98a4900 {
-			cd-gpios = <&msmgpio 62 0x1>;
-			pinctrl-names = "default";
-			pinctrl-0 = <&sdhc2_pin_a>, <&sdhc2_cd_pin_a>;
-			bus-width = <4>;
-			status = "okay";
+	pm8941-regulators {
+		compatible = "qcom,rpm-pm8941-regulators";
+
+		vdd_l1_l3-supply = <&pm8941_s1>;
+		vdd_l2_lvs1_2_3-supply = <&pm8941_s3>;
+		vdd_l4_l11-supply = <&pm8941_s1>;
+		vdd_l5_l7-supply = <&pm8941_s2>;
+		vdd_l6_l12_l14_l15-supply = <&pm8941_s2>;
+		vin_5vs-supply = <&pm8941_5v>;
+
+		pm8941_s1: s1 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
 
-			vmmc-supply = <&pm8941_l21>;
-			vqmmc-supply = <&pm8941_l13>;
+		pm8941_s2: s2 {
+			regulator-min-microvolt = <2150000>;
+			regulator-max-microvolt = <2150000>;
+			regulator-boot-on;
 		};
 
-		usb@f9a55000 {
-			status = "okay";
-			phys = <&usb_hs2_phy>;
-			phy-select = <&tcsr 0xb000 1>;
-			extcon = <&smbb>, <&usb_id>;
-			vbus-supply = <&chg_otg>;
-			hnp-disable;
-			srp-disable;
-			adp-disable;
-			ulpi {
-				phy@b {
-					status = "okay";
-					v3p3-supply = <&pm8941_l24>;
-					v1p8-supply = <&pm8941_l6>;
-					extcon = <&smbb>;
-					qcom,init-seq = /bits/ 8 <0x1 0x63>;
-				};
-			};
-		};
-
-
-		pinctrl@fd510000 {
-			i2c11_pins: i2c11 {
-				mux {
-					pins = "gpio83", "gpio84";
-					function = "blsp_i2c11";
-				};
-			};
-
-			spi8_default: spi8_default {
-				mosi {
-					pins = "gpio45";
-					function = "blsp_spi8";
-				};
-				miso {
-					pins = "gpio46";
-					function = "blsp_spi8";
-				};
-				cs {
-					pins = "gpio47";
-					function = "blsp_spi8";
-				};
-				clk {
-					pins = "gpio48";
-					function = "blsp_spi8";
-				};
-			};
-
-			sdhc1_pin_a: sdhc1-pin-active {
-				clk {
-					pins = "sdc1_clk";
-					drive-strength = <16>;
-					bias-disable;
-				};
-
-				cmd-data {
-					pins = "sdc1_cmd", "sdc1_data";
-					drive-strength = <10>;
-					bias-pull-up;
-				};
-			};
-
-			sdhc2_cd_pin_a: sdhc2-cd-pin-active {
-				pins = "gpio62";
-				function = "gpio";
-
-				drive-strength = <2>;
-				bias-disable;
-			};
-
-			sdhc2_pin_a: sdhc2-pin-active {
-				clk {
-					pins = "sdc2_clk";
-					drive-strength = <10>;
-					bias-disable;
-				};
-
-				cmd-data {
-					pins = "sdc2_cmd", "sdc2_data";
-					drive-strength = <6>;
-					bias-pull-up;
-				};
-			};
-		};
-
-		i2c@f9967000 {
-			status = "okay";
-			clock-frequency = <200000>;
-			pinctrl-0 = <&i2c11_pins>;
-			pinctrl-names = "default";
+		pm8941_s3: s3 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		pm8941_l1: l1 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		pm8941_l2: l2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8941_l3: l3 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+		};
+
+		pm8941_l4: l4 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+		};
+
+		pm8941_l5: l5 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
 
-			eeprom: eeprom@52 {
-				compatible = "atmel,24c128";
-				reg = <0x52>;
-				pagesize = <32>;
-				read-only;
-			};
+		pm8941_l6: l6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-boot-on;
+		};
+
+		pm8941_l7: l7 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-boot-on;
+		};
+
+		pm8941_l8: l8 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8941_l9: l9 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8941_l10: l10 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+		};
+
+		pm8941_l11: l11 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+		};
+
+		pm8941_l12: l12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		pm8941_l13: l13 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-boot-on;
+		};
+
+		pm8941_l14: l14 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8941_l15: l15 {
+			regulator-min-microvolt = <2050000>;
+			regulator-max-microvolt = <2050000>;
+		};
+
+		pm8941_l16: l16 {
+			regulator-min-microvolt = <2700000>;
+			regulator-max-microvolt = <2700000>;
+		};
+
+		pm8941_l17: l17 {
+			regulator-min-microvolt = <2700000>;
+			regulator-max-microvolt = <2700000>;
+		};
+
+		pm8941_l18: l18 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+		};
+
+		pm8941_l19: l19 {
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-always-on;
+		};
+
+		pm8941_l20: l20 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-system-load = <200000>;
+			regulator-allow-set-load;
+			regulator-boot-on;
+		};
+
+		pm8941_l21: l21 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-boot-on;
+		};
+
+		pm8941_l22: l22 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+		};
+
+		pm8941_l23: l23 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+		};
+
+		pm8941_l24: l24 {
+			regulator-min-microvolt = <3075000>;
+			regulator-max-microvolt = <3075000>;
+			regulator-boot-on;
 		};
 	};
+};
+
+&sdhc_1 {
+	status = "okay";
+
+	vmmc-supply = <&pm8941_l20>;
+	vqmmc-supply = <&pm8941_s3>;
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sdc1_on>;
+	pinctrl-1 = <&sdc1_off>;
+};
+
+&sdhc_2 {
+	status = "okay";
+
+	cd-gpios = <&tlmm 62 GPIO_ACTIVE_LOW>;
+	vmmc-supply = <&pm8941_l21>;
+	vqmmc-supply = <&pm8941_l13>;
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sdc2_on>;
+	pinctrl-1 = <&sdc2_off>;
+};
+
+&tlmm {
+	sdc1_on: sdc1-on {
+		clk {
+			pins = "sdc1_clk";
+			drive-strength = <16>;
+			bias-disable;
+		};
+
+		cmd-data {
+			pins = "sdc1_cmd", "sdc1_data";
+			drive-strength = <10>;
+			bias-pull-up;
+		};
+	};
+
+	sdc2_on: sdc2-on {
+		clk {
+			pins = "sdc2_clk";
+			drive-strength = <10>;
+			bias-disable;
+		};
+
+		cmd-data {
+			pins = "sdc2_cmd", "sdc2_data";
+			drive-strength = <6>;
+			bias-pull-up;
+		};
 
-	smd {
-		rpm {
-			rpm_requests {
-				pm8841-regulators {
-					s1 {
-						regulator-min-microvolt = <675000>;
-						regulator-max-microvolt = <1050000>;
-					};
-
-					s2 {
-						regulator-min-microvolt = <500000>;
-						regulator-max-microvolt = <1050000>;
-					};
-
-					s3 {
-						regulator-min-microvolt = <500000>;
-						regulator-max-microvolt = <1050000>;
-					};
-
-					s4 {
-						regulator-min-microvolt = <500000>;
-						regulator-max-microvolt = <1050000>;
-					};
-				};
-
-				pm8941-regulators {
-					vdd_l1_l3-supply = <&pm8941_s1>;
-					vdd_l2_lvs1_2_3-supply = <&pm8941_s3>;
-					vdd_l4_l11-supply = <&pm8941_s1>;
-					vdd_l5_l7-supply = <&pm8941_s2>;
-					vdd_l6_l12_l14_l15-supply = <&pm8941_s2>;
-					vin_5vs-supply = <&pm8941_5v>;
-
-					s1 {
-						regulator-min-microvolt = <1300000>;
-						regulator-max-microvolt = <1300000>;
-						regulator-always-on;
-						regulator-boot-on;
-					};
-
-					s2 {
-						regulator-min-microvolt = <2150000>;
-						regulator-max-microvolt = <2150000>;
-						regulator-boot-on;
-					};
-
-					s3 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-						regulator-always-on;
-						regulator-boot-on;
-					};
-
-					l1 {
-						regulator-min-microvolt = <1225000>;
-						regulator-max-microvolt = <1225000>;
-
-						regulator-always-on;
-						regulator-boot-on;
-					};
-
-					l2 {
-						regulator-min-microvolt = <1200000>;
-						regulator-max-microvolt = <1200000>;
-					};
-
-					l3 {
-						regulator-min-microvolt = <1225000>;
-						regulator-max-microvolt = <1225000>;
-					};
-
-					l4 {
-						regulator-min-microvolt = <1225000>;
-						regulator-max-microvolt = <1225000>;
-					};
-
-					l5 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-					};
-
-					l6 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-
-						regulator-boot-on;
-					};
-
-					l7 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-
-						regulator-boot-on;
-					};
-
-					l8 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-					};
-
-					l9 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <2950000>;
-					};
-
-					l10 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-						regulator-always-on;
-					};
-
-					l11 {
-						regulator-min-microvolt = <1300000>;
-						regulator-max-microvolt = <1300000>;
-					};
-
-					l12 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-
-						regulator-always-on;
-						regulator-boot-on;
-					};
-
-					l13 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <2950000>;
-
-						regulator-boot-on;
-					};
-
-					l14 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-					};
-
-					l15 {
-						regulator-min-microvolt = <2050000>;
-						regulator-max-microvolt = <2050000>;
-					};
-
-					l16 {
-						regulator-min-microvolt = <2700000>;
-						regulator-max-microvolt = <2700000>;
-					};
-
-					l17 {
-						regulator-min-microvolt = <2700000>;
-						regulator-max-microvolt = <2700000>;
-					};
-
-					l18 {
-						regulator-min-microvolt = <2850000>;
-						regulator-max-microvolt = <2850000>;
-					};
-
-					l19 {
-						regulator-min-microvolt = <3300000>;
-						regulator-max-microvolt = <3300000>;
-						regulator-always-on;
-					};
-
-					l20 {
-						regulator-min-microvolt = <2950000>;
-						regulator-max-microvolt = <2950000>;
-
-						regulator-allow-set-load;
-						regulator-boot-on;
-						regulator-system-load = <200000>;
-					};
-
-					l21 {
-						regulator-min-microvolt = <2950000>;
-						regulator-max-microvolt = <2950000>;
-
-						regulator-boot-on;
-					};
-
-					l22 {
-						regulator-min-microvolt = <3000000>;
-						regulator-max-microvolt = <3000000>;
-					};
-
-					l23 {
-						regulator-min-microvolt = <3000000>;
-						regulator-max-microvolt = <3000000>;
-					};
-
-					l24 {
-						regulator-min-microvolt = <3075000>;
-						regulator-max-microvolt = <3075000>;
-
-						regulator-boot-on;
-					};
-				};
-			};
+		cd {
+			pins = "gpio62";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-disable;
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/qcom-apq8084.dtsi b/arch/arm/boot/dts/qcom-apq8084.dtsi
index 52240fc7a1a6..f2fb7c975af8 100644
--- a/arch/arm/boot/dts/qcom-apq8084.dtsi
+++ b/arch/arm/boot/dts/qcom-apq8084.dtsi
@@ -95,7 +95,7 @@
 
 	firmware {
 		scm {
-			compatible = "qcom,scm";
+			compatible = "qcom,scm-apq8084", "qcom,scm";
 			clocks = <&gcc GCC_CE1_CLK> , <&gcc GCC_CE1_AXI_CLK>, <&gcc GCC_CE1_AHB_CLK>;
 			clock-names = "core", "bus", "iface";
 		};
@@ -239,11 +239,16 @@
 			reg = <0xf9011000 0x1000>;
 		};
 
+		sram@fc190000 {
+			compatible = "qcom,apq8084-rpm-stats";
+			reg = <0xfc190000 0x10000>;
+		};
+
 		qfprom: qfprom@fc4bc000 {
+			compatible = "qcom,apq8084-qfprom", "qcom,qfprom";
+			reg = <0xfc4bc000 0x1000>;
 			#address-cells = <1>;
 			#size-cells = <1>;
-			compatible = "qcom,qfprom";
-			reg = <0xfc4bc000 0x1000>;
 			tsens_calib: calib@d0 {
 				reg = <0xd0 0x18>;
 			};
@@ -383,14 +388,9 @@
 			reg = <0xfc400000 0x4000>;
 		};
 
-		tcsr_mutex_regs: syscon@fd484000 {
-			compatible = "syscon";
-			reg = <0xfd484000 0x2000>;
-		};
-
-		tcsr_mutex: hwlock {
-			compatible = "qcom,tcsr-mutex";
-			syscon = <&tcsr_mutex_regs 0 0x80>;
+		tcsr_mutex: hwlock@fd484000 {
+			compatible = "qcom,apq8084-tcsr-mutex", "qcom,tcsr-mutex";
+			reg = <0xfd484000 0x1000>;
 			#hwlock-cells = <1>;
 		};
 
@@ -419,29 +419,29 @@
 			status = "disabled";
 		};
 
-		sdhci@f9824900 {
+		mmc@f9824900 {
 			compatible = "qcom,apq8084-sdhci", "qcom,sdhci-msm-v4";
 			reg = <0xf9824900 0x11c>, <0xf9824000 0x800>;
-			reg-names = "hc_mem", "core_mem";
+			reg-names = "hc", "core";
 			interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "hc_irq", "pwr_irq";
-			clocks = <&gcc GCC_SDCC1_APPS_CLK>,
-				 <&gcc GCC_SDCC1_AHB_CLK>,
+			clocks = <&gcc GCC_SDCC1_AHB_CLK>,
+				 <&gcc GCC_SDCC1_APPS_CLK>,
 				 <&xo_board>;
-			clock-names = "core", "iface", "xo";
+			clock-names = "iface", "core", "xo";
 			status = "disabled";
 		};
 
-		sdhci@f98a4900 {
+		mmc@f98a4900 {
 			compatible = "qcom,apq8084-sdhci", "qcom,sdhci-msm-v4";
 			reg = <0xf98a4900 0x11c>, <0xf98a4000 0x800>;
-			reg-names = "hc_mem", "core_mem";
+			reg-names = "hc", "core";
 			interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 221 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "hc_irq", "pwr_irq";
-			clocks = <&gcc GCC_SDCC2_APPS_CLK>,
-				 <&gcc GCC_SDCC2_AHB_CLK>,
+			clocks = <&gcc GCC_SDCC2_AHB_CLK>,
+				 <&gcc GCC_SDCC2_APPS_CLK>,
 				 <&xo_board>;
-			clock-names = "core", "iface", "xo";
+			clock-names = "iface", "core", "xo";
 			status = "disabled";
 		};
 
@@ -470,7 +470,7 @@
 			qcom,ipc = <&apcs 8 0>;
 			qcom,smd-edge = <15>;
 
-			rpm_requests {
+			rpm-requests {
 				compatible = "qcom,rpm-apq8084";
 				qcom,smd-channels = "rpm_requests";
 
diff --git a/arch/arm/boot/dts/qcom-ipq4018-ap120c-ac-bit.dts b/arch/arm/boot/dts/qcom-ipq4018-ap120c-ac-bit.dts
index 028ac8e24797..cf7da1ab177c 100644
--- a/arch/arm/boot/dts/qcom-ipq4018-ap120c-ac-bit.dts
+++ b/arch/arm/boot/dts/qcom-ipq4018-ap120c-ac-bit.dts
@@ -1,5 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
 
+#include <dt-bindings/leds/common.h>
 #include "qcom-ipq4018-ap120c-ac.dtsi"
 
 / {
@@ -10,17 +11,22 @@
 
 		power {
 			label = "ap120c-ac:green:power";
+			function = LED_FUNCTION_POWER;
+			color = <LED_COLOR_ID_GREEN>;
 			gpios = <&tlmm 5 GPIO_ACTIVE_LOW>;
 			default-state = "on";
 		};
 
 		wlan {
 			label = "ap120c-ac:green:wlan";
+			function = LED_FUNCTION_WLAN;
+			color = <LED_COLOR_ID_GREEN>;
 			gpios = <&tlmm 3 GPIO_ACTIVE_HIGH>;
 		};
 
 		support {
 			label = "ap120c-ac:green:support";
+			color = <LED_COLOR_ID_GREEN>;
 			gpios = <&tlmm 2 GPIO_ACTIVE_HIGH>;
 			panic-indicator;
 		};
diff --git a/arch/arm/boot/dts/qcom-ipq4018-ap120c-ac.dts b/arch/arm/boot/dts/qcom-ipq4018-ap120c-ac.dts
index b7916fc26d68..c4f89b712fd9 100644
--- a/arch/arm/boot/dts/qcom-ipq4018-ap120c-ac.dts
+++ b/arch/arm/boot/dts/qcom-ipq4018-ap120c-ac.dts
@@ -1,5 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0-or-later OR MIT
 
+#include <dt-bindings/leds/common.h>
 #include "qcom-ipq4018-ap120c-ac.dtsi"
 
 / {
@@ -8,18 +9,24 @@
 
 		status: status {
 			label = "ap120c-ac:blue:status";
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_BLUE>;
 			gpios = <&tlmm 5 GPIO_ACTIVE_LOW>;
 			default-state = "keep";
 		};
 
 		wlan2g {
 			label = "ap120c-ac:green:wlan2g";
+			function = LED_FUNCTION_WLAN;
+			color = <LED_COLOR_ID_GREEN>;
 			gpios = <&tlmm 3 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "phy0tpt";
 		};
 
 		wlan5g {
 			label = "ap120c-ac:red:wlan5g";
+			function = LED_FUNCTION_WLAN;
+			color = <LED_COLOR_ID_RED>;
 			gpios = <&tlmm 2 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "phy1tpt";
 		};
diff --git a/arch/arm/boot/dts/qcom-ipq4018-ap120c-ac.dtsi b/arch/arm/boot/dts/qcom-ipq4018-ap120c-ac.dtsi
index 1f3b1ce82108..af9a26fb5d4a 100644
--- a/arch/arm/boot/dts/qcom-ipq4018-ap120c-ac.dtsi
+++ b/arch/arm/boot/dts/qcom-ipq4018-ap120c-ac.dtsi
@@ -11,7 +11,7 @@
 	keys {
 		compatible = "gpio-keys";
 
-		reset {
+		key-reset {
 			label = "reset";
 			gpios = <&tlmm 63 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_RESTART>;
diff --git a/arch/arm/boot/dts/qcom-ipq4019-ap.dk01.1.dtsi b/arch/arm/boot/dts/qcom-ipq4019-ap.dk01.1.dtsi
index 0c10d9e096db..0505270cf508 100644
--- a/arch/arm/boot/dts/qcom-ipq4019-ap.dk01.1.dtsi
+++ b/arch/arm/boot/dts/qcom-ipq4019-ap.dk01.1.dtsi
@@ -14,6 +14,7 @@
  *
  */
 
+#include <dt-bindings/gpio/gpio.h>
 #include "qcom-ipq4019.dtsi"
 
 / {
@@ -64,7 +65,7 @@
 			};
 		};
 
-		blsp_dma: dma@7884000 {
+		blsp_dma: dma-controller@7884000 {
 			status = "okay";
 		};
 
@@ -72,7 +73,7 @@
 			pinctrl-0 = <&spi_0_pins>;
 			pinctrl-names = "default";
 			status = "okay";
-			cs-gpios = <&tlmm 54 0>;
+			cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>;
 
 			mx25l25635e@0 {
 				#address-cells = <1>;
@@ -89,7 +90,7 @@
 			status = "okay";
 		};
 
-		cryptobam: dma@8e04000 {
+		cryptobam: dma-controller@8e04000 {
 			status = "okay";
 		};
 
diff --git a/arch/arm/boot/dts/qcom-ipq4019-ap.dk04.1-c1.dts b/arch/arm/boot/dts/qcom-ipq4019-ap.dk04.1-c1.dts
index a7b1201dd614..79b0c6318e52 100644
--- a/arch/arm/boot/dts/qcom-ipq4019-ap.dk04.1-c1.dts
+++ b/arch/arm/boot/dts/qcom-ipq4019-ap.dk04.1-c1.dts
@@ -8,7 +8,7 @@
 	compatible = "qcom,ipq4019-dk04.1-c1", "qcom,ipq4019";
 
 	soc {
-		dma@7984000 {
+		dma-controller@7984000 {
 			status = "okay";
 		};
 
diff --git a/arch/arm/boot/dts/qcom-ipq4019-ap.dk04.1.dtsi b/arch/arm/boot/dts/qcom-ipq4019-ap.dk04.1.dtsi
index 7a337dc08741..a63b3778636d 100644
--- a/arch/arm/boot/dts/qcom-ipq4019-ap.dk04.1.dtsi
+++ b/arch/arm/boot/dts/qcom-ipq4019-ap.dk04.1.dtsi
@@ -79,7 +79,7 @@
 			status = "okay";
 		};
 
-		dma@7884000 {
+		dma-controller@7884000 {
 			status = "okay";
 		};
 
@@ -87,20 +87,20 @@
 			pinctrl-0 = <&spi_0_pins>;
 			pinctrl-names = "default";
 			status = "okay";
-			cs-gpios = <&tlmm 12 0>;
+			cs-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>;
 
-			m25p80@0 {
+			flash@0 {
 				#address-cells = <1>;
 				#size-cells = <1>;
 				reg = <0>;
-				compatible = "n25q128a11";
+				compatible = "micron,n25q128a11", "jedec,spi-nor";
 				spi-max-frequency = <24000000>;
 			};
 		};
 
 		pci@40000000 {
 			status = "okay";
-			perst-gpio = <&tlmm 38 0x1>;
+			perst-gpios = <&tlmm 38 GPIO_ACTIVE_LOW>;
 		};
 
 		qpic-nand@79b0000 {
diff --git a/arch/arm/boot/dts/qcom-ipq4019-ap.dk07.1-c1.dts b/arch/arm/boot/dts/qcom-ipq4019-ap.dk07.1-c1.dts
index 06f9f2cb2fe9..ea2987fcbff8 100644
--- a/arch/arm/boot/dts/qcom-ipq4019-ap.dk07.1-c1.dts
+++ b/arch/arm/boot/dts/qcom-ipq4019-ap.dk07.1-c1.dts
@@ -1,6 +1,7 @@
 // SPDX-License-Identifier: GPL-2.0
 // Copyright (c) 2018, The Linux Foundation. All rights reserved.
 
+#include <dt-bindings/gpio/gpio.h>
 #include "qcom-ipq4019-ap.dk07.1.dtsi"
 
 / {
@@ -10,7 +11,7 @@
 	soc {
 		pci@40000000 {
 			status = "okay";
-			perst-gpio = <&tlmm 38 0x1>;
+			perst-gpios = <&tlmm 38 GPIO_ACTIVE_LOW>;
 		};
 
 		spi@78b6000 {
@@ -50,13 +51,13 @@
 			pinctrl-0 = <&spi_0_pins>;
 			pinctrl-names = "default";
 			status = "okay";
-			cs-gpios = <&tlmm 12 0>;
+			cs-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>;
 
-			m25p80@0 {
+			flash@0 {
 				#address-cells = <1>;
 				#size-cells = <1>;
 				reg = <0>;
-				compatible = "n25q128a11";
+				compatible = "micron,n25q128a11", "jedec,spi-nor";
 				spi-max-frequency = <24000000>;
 			};
 		};
diff --git a/arch/arm/boot/dts/qcom-ipq4019-ap.dk07.1.dtsi b/arch/arm/boot/dts/qcom-ipq4019-ap.dk07.1.dtsi
index 94872518b5a2..0107f552f520 100644
--- a/arch/arm/boot/dts/qcom-ipq4019-ap.dk07.1.dtsi
+++ b/arch/arm/boot/dts/qcom-ipq4019-ap.dk07.1.dtsi
@@ -52,7 +52,7 @@
 			status = "okay";
 		};
 
-		dma@7884000 {
+		dma-controller@7884000 {
 			status = "okay";
 		};
 
@@ -62,7 +62,7 @@
 			status = "okay";
 		};
 
-		dma@7984000 {
+		dma-controller@7984000 {
 			status = "okay";
 		};
 
diff --git a/arch/arm/boot/dts/qcom-ipq4019.dtsi b/arch/arm/boot/dts/qcom-ipq4019.dtsi
index ff1bdb10ad19..b23591110bd2 100644
--- a/arch/arm/boot/dts/qcom-ipq4019.dtsi
+++ b/arch/arm/boot/dts/qcom-ipq4019.dtsi
@@ -142,7 +142,8 @@
 	clocks {
 		sleep_clk: sleep_clk {
 			compatible = "fixed-clock";
-			clock-frequency = <32768>;
+			clock-frequency = <32000>;
+			clock-output-names = "gcc_sleep_clk_src";
 			#clock-cells = <0>;
 		};
 
@@ -155,7 +156,7 @@
 
 	firmware {
 		scm {
-			compatible = "qcom,scm-ipq4019";
+			compatible = "qcom,scm-ipq4019", "qcom,scm";
 		};
 	};
 
@@ -186,6 +187,7 @@
 		gcc: clock-controller@1800000 {
 			compatible = "qcom,gcc-ipq4019";
 			#clock-cells = <1>;
+			#power-domain-cells = <1>;
 			#reset-cells = <1>;
 			reg = <0x1800000 0x60000>;
 		};
@@ -219,19 +221,20 @@
 			status = "disabled";
 		};
 
-		sdhci: sdhci@7824900 {
+		sdhci: mmc@7824900 {
 			compatible = "qcom,sdhci-msm-v4";
 			reg = <0x7824900 0x11c>, <0x7824000 0x800>;
+			reg-names = "hc", "core";
 			interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "hc_irq", "pwr_irq";
 			bus-width = <8>;
-			clocks = <&gcc GCC_SDCC1_APPS_CLK>, <&gcc GCC_SDCC1_AHB_CLK>,
+			clocks = <&gcc GCC_SDCC1_AHB_CLK>, <&gcc GCC_SDCC1_APPS_CLK>,
 				 <&gcc GCC_DCD_XO_CLK>;
-			clock-names = "core", "iface", "xo";
+			clock-names = "iface", "core", "xo";
 			status = "disabled";
 		};
 
-		blsp_dma: dma@7884000 {
+		blsp_dma: dma-controller@7884000 {
 			compatible = "qcom,bam-v1.7.0";
 			reg = <0x07884000 0x23000>;
 			interrupts = <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>;
@@ -251,8 +254,8 @@
 			clock-names = "core", "iface";
 			#address-cells = <1>;
 			#size-cells = <0>;
-			dmas = <&blsp_dma 5>, <&blsp_dma 4>;
-			dma-names = "rx", "tx";
+			dmas = <&blsp_dma 4>, <&blsp_dma 5>;
+			dma-names = "tx", "rx";
 			status = "disabled";
 		};
 
@@ -265,8 +268,8 @@
 			clock-names = "core", "iface";
 			#address-cells = <1>;
 			#size-cells = <0>;
-			dmas = <&blsp_dma 7>, <&blsp_dma 6>;
-			dma-names = "rx", "tx";
+			dmas = <&blsp_dma 6>, <&blsp_dma 7>;
+			dma-names = "tx", "rx";
 			status = "disabled";
 		};
 
@@ -274,13 +277,13 @@
 			compatible = "qcom,i2c-qup-v2.2.1";
 			reg = <0x78b7000 0x600>;
 			interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc GCC_BLSP1_AHB_CLK>,
-				 <&gcc GCC_BLSP1_QUP1_I2C_APPS_CLK>;
-			clock-names = "iface", "core";
+			clocks = <&gcc GCC_BLSP1_QUP1_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
 			#address-cells = <1>;
 			#size-cells = <0>;
-			dmas = <&blsp_dma 9>, <&blsp_dma 8>;
-			dma-names = "rx", "tx";
+			dmas = <&blsp_dma 8>, <&blsp_dma 9>;
+			dma-names = "tx", "rx";
 			status = "disabled";
 		};
 
@@ -288,17 +291,17 @@
 			compatible = "qcom,i2c-qup-v2.2.1";
 			reg = <0x78b8000 0x600>;
 			interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc GCC_BLSP1_AHB_CLK>,
-				 <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>;
-			clock-names = "iface", "core";
+			clocks = <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
 			#address-cells = <1>;
 			#size-cells = <0>;
-			dmas = <&blsp_dma 11>, <&blsp_dma 10>;
-			dma-names = "rx", "tx";
+			dmas = <&blsp_dma 10>, <&blsp_dma 11>;
+			dma-names = "tx", "rx";
 			status = "disabled";
 		};
 
-		cryptobam: dma@8e04000 {
+		cryptobam: dma-controller@8e04000 {
 			compatible = "qcom,bam-v1.7.0";
 			reg = <0x08e04000 0x20000>;
 			interrupts = <GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH>;
@@ -380,8 +383,8 @@
 			clocks = <&gcc GCC_BLSP1_UART1_APPS_CLK>,
 				<&gcc GCC_BLSP1_AHB_CLK>;
 			clock-names = "core", "iface";
-			dmas = <&blsp_dma 1>, <&blsp_dma 0>;
-			dma-names = "rx", "tx";
+			dmas = <&blsp_dma 0>, <&blsp_dma 1>;
+			dma-names = "tx", "rx";
 		};
 
 		blsp1_uart2: serial@78b0000 {
@@ -392,8 +395,8 @@
 			clocks = <&gcc GCC_BLSP1_UART2_APPS_CLK>,
 				<&gcc GCC_BLSP1_AHB_CLK>;
 			clock-names = "core", "iface";
-			dmas = <&blsp_dma 3>, <&blsp_dma 2>;
-			dma-names = "rx", "tx";
+			dmas = <&blsp_dma 2>, <&blsp_dma 3>;
+			dma-names = "tx", "rx";
 		};
 
 		watchdog: watchdog@b017000 {
@@ -410,7 +413,7 @@
 		};
 
 		pcie0: pci@40000000 {
-			compatible = "qcom,pcie-ipq4019", "snps,dw-pcie";
+			compatible = "qcom,pcie-ipq4019";
 			reg =  <0x40000000 0xf1d
 				0x40000f20 0xa8
 				0x80000 0x2000
@@ -469,7 +472,7 @@
 			status = "disabled";
 		};
 
-		qpic_bam: dma@7984000 {
+		qpic_bam: dma-controller@7984000 {
 			compatible = "qcom,bam-v1.7.0";
 			reg = <0x7984000 0x1a000>;
 			interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
@@ -637,14 +640,14 @@
 		};
 
 		usb3: usb3@8af8800 {
-			compatible = "qcom,dwc3";
+			compatible = "qcom,ipq4019-dwc3", "qcom,dwc3";
 			reg = <0x8af8800 0x100>;
 			#address-cells = <1>;
 			#size-cells = <1>;
 			clocks = <&gcc GCC_USB3_MASTER_CLK>,
 				 <&gcc GCC_USB3_SLEEP_CLK>,
 				 <&gcc GCC_USB3_MOCK_UTMI_CLK>;
-			clock-names = "master", "sleep", "mock_utmi";
+			clock-names = "core", "sleep", "mock_utmi";
 			ranges;
 			status = "disabled";
 
@@ -669,7 +672,7 @@
 		};
 
 		usb2: usb2@60f8800 {
-			compatible = "qcom,dwc3";
+			compatible = "qcom,ipq4019-dwc3", "qcom,dwc3";
 			reg = <0x60f8800 0x100>;
 			#address-cells = <1>;
 			#size-cells = <1>;
diff --git a/arch/arm/boot/dts/qcom-ipq8062-smb208.dtsi b/arch/arm/boot/dts/qcom-ipq8062-smb208.dtsi
new file mode 100644
index 000000000000..9d06255104c7
--- /dev/null
+++ b/arch/arm/boot/dts/qcom-ipq8062-smb208.dtsi
@@ -0,0 +1,37 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+#include "qcom-ipq8062.dtsi"
+
+&rpm {
+	smb208_regulators: regulators {
+		compatible = "qcom,rpm-smb208-regulators";
+
+		smb208_s1a: s1a {
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1150000>;
+
+			qcom,switch-mode-frequency = <1200000>;
+		};
+
+		smb208_s1b: s1b {
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1150000>;
+
+			qcom,switch-mode-frequency = <1200000>;
+		};
+
+		smb208_s2a: s2a {
+			regulator-min-microvolt = < 800000>;
+			regulator-max-microvolt = <1150000>;
+
+			qcom,switch-mode-frequency = <1200000>;
+		};
+
+		smb208_s2b: s2b {
+			regulator-min-microvolt = < 800000>;
+			regulator-max-microvolt = <1150000>;
+
+			qcom,switch-mode-frequency = <1200000>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/qcom-ipq8062.dtsi b/arch/arm/boot/dts/qcom-ipq8062.dtsi
new file mode 100644
index 000000000000..5d3ebd3e2e51
--- /dev/null
+++ b/arch/arm/boot/dts/qcom-ipq8062.dtsi
@@ -0,0 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+#include "qcom-ipq8064-v2.0.dtsi"
+
+/ {
+	model = "Qualcomm Technologies, Inc. IPQ8062";
+	compatible = "qcom,ipq8062", "qcom,ipq8064";
+};
diff --git a/arch/arm/boot/dts/qcom-ipq8064-ap148.dts b/arch/arm/boot/dts/qcom-ipq8064-ap148.dts
index b63d01d10189..a654d3c22c4f 100644
--- a/arch/arm/boot/dts/qcom-ipq8064-ap148.dts
+++ b/arch/arm/boot/dts/qcom-ipq8064-ap148.dts
@@ -7,12 +7,6 @@
 
 	soc {
 		pinmux@800000 {
-			i2c4_pins: i2c4_pinmux {
-				pins = "gpio12", "gpio13";
-				function = "gsbi4";
-				bias-disable;
-			};
-
 			buttons_pins: buttons_pins {
 				mux {
 					pins = "gpio54", "gpio65";
diff --git a/arch/arm/boot/dts/qcom-ipq8064-rb3011.dts b/arch/arm/boot/dts/qcom-ipq8064-rb3011.dts
index 596d129d4a95..5a65cce2500c 100644
--- a/arch/arm/boot/dts/qcom-ipq8064-rb3011.dts
+++ b/arch/arm/boot/dts/qcom-ipq8064-rb3011.dts
@@ -1,6 +1,7 @@
 // SPDX-License-Identifier: GPL-2.0
 #include "qcom-ipq8064.dtsi"
 #include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
 
 / {
 	model = "MikroTik RB3011UiAS-RM";
@@ -187,12 +188,12 @@
 			};
 		};
 
-		gpio_keys {
+		gpio-keys {
 			compatible = "gpio-keys";
 			pinctrl-0 = <&buttons_pins>;
 			pinctrl-names = "default";
 
-			button@1 {
+			button {
 				label = "reset";
 				linux,code = <KEY_RESTART>;
 				gpios = <&qcom_pinmux 66 GPIO_ACTIVE_LOW>;
@@ -208,6 +209,7 @@
 
 			led@7 {
 				label = "rb3011:green:user";
+				color = <LED_COLOR_ID_GREEN>;
 				gpios = <&qcom_pinmux 33 GPIO_ACTIVE_HIGH>;
 				default-state = "off";
 			};
@@ -305,15 +307,6 @@
 		};
 	};
 
-	mdio0_pins: mdio0_pins {
-		mux {
-			pins = "gpio0", "gpio1";
-			function = "gpio";
-			drive-strength = <8>;
-			bias-disable;
-		};
-	};
-
 	mdio1_pins: mdio1_pins {
 		mux {
 			pins = "gpio10", "gpio11";
diff --git a/arch/arm/boot/dts/qcom-ipq8064-smb208.dtsi b/arch/arm/boot/dts/qcom-ipq8064-smb208.dtsi
new file mode 100644
index 000000000000..ac9c44f0c164
--- /dev/null
+++ b/arch/arm/boot/dts/qcom-ipq8064-smb208.dtsi
@@ -0,0 +1,37 @@
+// SPDX-License-Identifier: GPL-2.0
+
+#include "qcom-ipq8064.dtsi"
+
+&rpm {
+	smb208_regulators: regulators {
+		compatible = "qcom,rpm-smb208-regulators";
+
+		smb208_s1a: s1a {
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1150000>;
+
+			qcom,switch-mode-frequency = <1200000>;
+		};
+
+		smb208_s1b: s1b {
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1150000>;
+
+			qcom,switch-mode-frequency = <1200000>;
+		};
+
+		smb208_s2a: s2a {
+			regulator-min-microvolt = < 800000>;
+			regulator-max-microvolt = <1250000>;
+
+			qcom,switch-mode-frequency = <1200000>;
+		};
+
+		smb208_s2b: s2b {
+			regulator-min-microvolt = < 800000>;
+			regulator-max-microvolt = <1250000>;
+
+			qcom,switch-mode-frequency = <1200000>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/qcom-ipq8064-v1.0.dtsi b/arch/arm/boot/dts/qcom-ipq8064-v1.0.dtsi
index 65330065390a..411c8d63c38e 100644
--- a/arch/arm/boot/dts/qcom-ipq8064-v1.0.dtsi
+++ b/arch/arm/boot/dts/qcom-ipq8064-v1.0.dtsi
@@ -1,6 +1,7 @@
 // SPDX-License-Identifier: GPL-2.0
 #include "qcom-ipq8064.dtsi"
 #include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
 
 / {
 	model = "Qualcomm Technologies, Inc. IPQ8064-v1.0";
@@ -36,7 +37,7 @@
 
 				cs-gpios = <&qcom_pinmux 20 0>;
 
-				flash: m25p80@0 {
+				flash: flash@0 {
 					compatible = "s25fl256s1";
 					#address-cells = <1>;
 					#size-cells = <1>;
@@ -65,19 +66,19 @@
 			status = "okay";
 		};
 
-		gpio_keys {
+		gpio-keys {
 			compatible = "gpio-keys";
 			pinctrl-0 = <&buttons_pins>;
 			pinctrl-names = "default";
 
-			button@1 {
+			button-1 {
 				label = "reset";
 				linux,code = <KEY_RESTART>;
 				gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>;
 				linux,input-type = <1>;
 				debounce-interval = <60>;
 			};
-			button@2 {
+			button-2 {
 				label = "wps";
 				linux,code = <KEY_WPS_BUTTON>;
 				gpios = <&qcom_pinmux 65 GPIO_ACTIVE_LOW>;
@@ -107,6 +108,7 @@
 
 			led@9 {
 				label = "status_led_fail";
+				function = LED_FUNCTION_STATUS;
 				gpios = <&qcom_pinmux 9 GPIO_ACTIVE_HIGH>;
 				default-state = "off";
 			};
@@ -119,6 +121,7 @@
 
 			led@53 {
 				label = "status_led_pass";
+				function = LED_FUNCTION_STATUS;
 				gpios = <&qcom_pinmux 53 GPIO_ACTIVE_HIGH>;
 				default-state = "off";
 			};
diff --git a/arch/arm/boot/dts/qcom-ipq8064-v2.0-smb208.dtsi b/arch/arm/boot/dts/qcom-ipq8064-v2.0-smb208.dtsi
new file mode 100644
index 000000000000..0442580b22de
--- /dev/null
+++ b/arch/arm/boot/dts/qcom-ipq8064-v2.0-smb208.dtsi
@@ -0,0 +1,37 @@
+// SPDX-License-Identifier: GPL-2.0
+
+#include "qcom-ipq8064-v2.0.dtsi"
+
+&rpm {
+	smb208_regulators: regulators {
+		compatible = "qcom,rpm-smb208-regulators";
+
+		smb208_s1a: s1a {
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1150000>;
+
+			qcom,switch-mode-frequency = <1200000>;
+		};
+
+		smb208_s1b: s1b {
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1150000>;
+
+			qcom,switch-mode-frequency = <1200000>;
+		};
+
+		smb208_s2a: s2a {
+			regulator-min-microvolt = < 800000>;
+			regulator-max-microvolt = <1250000>;
+
+			qcom,switch-mode-frequency = <1200000>;
+		};
+
+		smb208_s2b: s2b {
+			regulator-min-microvolt = < 800000>;
+			regulator-max-microvolt = <1250000>;
+
+			qcom,switch-mode-frequency = <1200000>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/qcom-ipq8064-v2.0.dtsi b/arch/arm/boot/dts/qcom-ipq8064-v2.0.dtsi
new file mode 100644
index 000000000000..2f117d576daf
--- /dev/null
+++ b/arch/arm/boot/dts/qcom-ipq8064-v2.0.dtsi
@@ -0,0 +1,69 @@
+// SPDX-License-Identifier: GPL-2.0
+
+#include "qcom-ipq8064.dtsi"
+
+/ {
+	model = "Qualcomm Technologies, Inc. IPQ8064-v2.0";
+
+	aliases {
+		serial0 = &gsbi4_serial;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		rsvd@41200000 {
+			reg = <0x41200000 0x300000>;
+			no-map;
+		};
+	};
+};
+
+&gsbi4 {
+	qcom,mode = <GSBI_PROT_I2C_UART>;
+	status = "okay";
+
+	serial@16340000 {
+		status = "okay";
+	};
+	/*
+	 * The i2c device on gsbi4 should not be enabled.
+	 * On ipq806x designs gsbi4 i2c is meant for exclusive
+	 * RPM usage. Turning this on in kernel manifests as
+	 * i2c failure for the RPM.
+	 */
+};
+
+&pcie0 {
+	compatible = "qcom,pcie-ipq8064-v2";
+};
+
+&pcie1 {
+	compatible = "qcom,pcie-ipq8064-v2";
+};
+
+&pcie2 {
+	compatible = "qcom,pcie-ipq8064-v2";
+};
+
+&sata {
+	ports-implemented = <0x1>;
+};
+
+&ss_phy_0 {
+	qcom,rx-eq = <2>;
+	qcom,tx-deamp_3_5db = <32>;
+	qcom,mpll = <5>;
+};
+
+&ss_phy_1 {
+	qcom,rx-eq = <2>;
+	qcom,tx-deamp_3_5db = <32>;
+	qcom,mpll = <5>;
+};
diff --git a/arch/arm/boot/dts/qcom-ipq8064.dtsi b/arch/arm/boot/dts/qcom-ipq8064.dtsi
index 11481313bdb6..90c08b51680a 100644
--- a/arch/arm/boot/dts/qcom-ipq8064.dtsi
+++ b/arch/arm/boot/dts/qcom-ipq8064.dtsi
@@ -292,19 +292,22 @@
 		};
 
 		smem: smem@41000000 {
+			compatible = "qcom,smem";
 			reg = <0x41000000 0x200000>;
 			no-map;
+
+			hwlocks = <&sfpb_mutex 3>;
 		};
 	};
 
 	clocks {
-		cxo_board {
+		cxo_board: cxo_board {
 			compatible = "fixed-clock";
 			#clock-cells = <0>;
 			clock-frequency = <25000000>;
 		};
 
-		pxo_board {
+		pxo_board: pxo_board {
 			compatible = "fixed-clock";
 			#clock-cells = <0>;
 			clock-frequency = <25000000>;
@@ -329,24 +332,64 @@
 		ranges;
 		compatible = "simple-bus";
 
-		lpass@28100000 {
-			compatible = "qcom,lpass-cpu";
-			status = "disabled";
-			clocks = <&lcc AHBIX_CLK>,
-					<&lcc MI2S_OSR_CLK>,
-					<&lcc MI2S_BIT_CLK>;
-			clock-names = "ahbix-clk",
-					"mi2s-osr-clk",
-					"mi2s-bit-clk";
-			interrupts = <GIC_SPI 85 IRQ_TYPE_EDGE_RISING>;
-			interrupt-names = "lpass-irq-lpaif";
-			reg = <0x28100000 0x10000>;
-			reg-names = "lpass-lpaif";
+		stmmac_axi_setup: stmmac-axi-config {
+			snps,wr_osr_lmt = <7>;
+			snps,rd_osr_lmt = <7>;
+			snps,blen = <16 0 0 0 0 0 0>;
+		};
+
+		vsdcc_fixed: vsdcc-regulator {
+			compatible = "regulator-fixed";
+			regulator-name = "SDCC Power";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-always-on;
+		};
+
+		rpm: rpm@108000 {
+			compatible = "qcom,rpm-ipq8064";
+			reg = <0x00108000 0x1000>;
+			qcom,ipc = <&l2cc 0x8 2>;
+
+			interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "ack", "err", "wakeup";
+
+			clocks = <&gcc RPM_MSG_RAM_H_CLK>;
+			clock-names = "ram";
+
+			rpmcc: clock-controller {
+				compatible = "qcom,rpmcc-ipq806x", "qcom,rpmcc";
+				#clock-cells = <1>;
+			};
+		};
+
+		qcom,ssbi@500000 {
+			compatible = "qcom,ssbi";
+			reg = <0x00500000 0x1000>;
+			qcom,controller-type = "pmic-arbiter";
+		};
+
+		qfprom: qfprom@700000 {
+			compatible = "qcom,ipq8064-qfprom", "qcom,qfprom";
+			reg = <0x00700000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			speedbin_efuse: speedbin@c0 {
+				reg = <0xc0 0x4>;
+			};
+			tsens_calib: calib@400 {
+				reg = <0x400 0xb>;
+			};
+			tsens_calib_backup: calib_backup@410 {
+				reg = <0x410 0xb>;
+			};
 		};
 
 		qcom_pinmux: pinmux@800000 {
 			compatible = "qcom,ipq8064-pinctrl";
-			reg = <0x800000 0x4000>;
+			reg = <0x00800000 0x4000>;
 
 			gpio-controller;
 			gpio-ranges = <&qcom_pinmux 0 0 69>;
@@ -382,6 +425,13 @@
 				};
 			};
 
+			i2c4_pins: i2c4-default {
+				pins = "gpio12", "gpio13";
+				function = "gsbi4";
+				drive-strength = <12>;
+				bias-disable;
+			};
+
 			spi_pins: spi_pins {
 				mux {
 					pins = "gpio18", "gpio19", "gpio21";
@@ -424,6 +474,8 @@
 
 				pullups {
 					pins = "gpio39";
+					function = "nand";
+					drive-strength = <10>;
 					bias-pull-up;
 				};
 
@@ -431,9 +483,61 @@
 					pins = "gpio40", "gpio41", "gpio42",
 					       "gpio43", "gpio44", "gpio45",
 					       "gpio46", "gpio47";
+					function = "nand";
+					drive-strength = <10>;
 					bias-bus-hold;
 				};
 			};
+
+			mdio0_pins: mdio0-pins {
+				mux {
+					pins = "gpio0", "gpio1";
+					function = "mdio";
+					drive-strength = <8>;
+					bias-disable;
+				};
+			};
+
+			rgmii2_pins: rgmii2-pins {
+				mux {
+					pins = "gpio27", "gpio28", "gpio29",
+					       "gpio30", "gpio31", "gpio32",
+					       "gpio51", "gpio52", "gpio59",
+					       "gpio60", "gpio61", "gpio62";
+					function = "rgmii2";
+					drive-strength = <8>;
+					bias-disable;
+				};
+			};
+		};
+
+		gcc: clock-controller@900000 {
+			compatible = "qcom,gcc-ipq8064", "syscon";
+			clocks = <&pxo_board>, <&cxo_board>;
+			clock-names = "pxo", "cxo";
+			reg = <0x00900000 0x4000>;
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+			#power-domain-cells = <1>;
+
+			tsens: thermal-sensor@900000 {
+				compatible = "qcom,ipq8064-tsens";
+
+				nvmem-cells = <&tsens_calib>, <&tsens_calib_backup>;
+				nvmem-cell-names = "calib", "calib_backup";
+				interrupts = <GIC_SPI 178 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "uplow";
+
+				#qcom,sensors = <11>;
+				#thermal-sensor-cells = <1>;
+			};
+		};
+
+		sfpb_mutex: hwlock@1200600 {
+			compatible = "qcom,sfpb-mutex";
+			reg = <0x01200600 0x100>;
+
+			#hwlock-cells = <1>;
 		};
 
 		intc: interrupt-controller@2000000 {
@@ -465,46 +569,236 @@
 			cpu-offset = <0x80000>;
 		};
 
+		l2cc: clock-controller@2011000 {
+			compatible = "qcom,kpss-gcc", "syscon";
+			reg = <0x02011000 0x1000>;
+			clocks = <&gcc PLL8_VOTE>, <&pxo_board>;
+			clock-names = "pll8_vote", "pxo";
+			clock-output-names = "acpu_l2_aux";
+		};
+
 		acc0: clock-controller@2088000 {
 			compatible = "qcom,kpss-acc-v1";
 			reg = <0x02088000 0x1000>, <0x02008000 0x1000>;
 		};
 
+		saw0: regulator@2089000 {
+			compatible = "qcom,saw2";
+			reg = <0x02089000 0x1000>, <0x02009000 0x1000>;
+			regulator;
+		};
+
 		acc1: clock-controller@2098000 {
 			compatible = "qcom,kpss-acc-v1";
 			reg = <0x02098000 0x1000>, <0x02008000 0x1000>;
 		};
 
-		adm_dma: dma-controller@18300000 {
-			compatible = "qcom,adm";
-			reg = <0x18300000 0x100000>;
-			interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>;
-			#dma-cells = <1>;
+		saw1: regulator@2099000 {
+			compatible = "qcom,saw2";
+			reg = <0x02099000 0x1000>, <0x02009000 0x1000>;
+			regulator;
+		};
 
-			clocks = <&gcc ADM0_CLK>, <&gcc ADM0_PBUS_CLK>;
-			clock-names = "core", "iface";
+		nss_common: syscon@03000000 {
+			compatible = "syscon";
+			reg = <0x03000000 0x0000FFFF>;
+		};
 
-			resets = <&gcc ADM0_RESET>,
-				 <&gcc ADM0_PBUS_RESET>,
-				 <&gcc ADM0_C0_RESET>,
-				 <&gcc ADM0_C1_RESET>,
-				 <&gcc ADM0_C2_RESET>;
-			reset-names = "clk", "pbus", "c0", "c1", "c2";
-			qcom,ee = <0>;
+		usb3_0: usb3@100f8800 {
+			compatible = "qcom,ipq8064-dwc3", "qcom,dwc3";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			reg = <0x100f8800 0x8000>;
+			clocks = <&gcc USB30_0_MASTER_CLK>;
+			clock-names = "core";
+
+			ranges;
+
+			resets = <&gcc USB30_0_MASTER_RESET>;
+			reset-names = "master";
 
 			status = "disabled";
+
+			dwc3_0: dwc3@10000000 {
+				compatible = "snps,dwc3";
+				reg = <0x10000000 0xcd00>;
+				interrupts = <GIC_SPI 205 IRQ_TYPE_LEVEL_HIGH>;
+				phys = <&hs_phy_0>, <&ss_phy_0>;
+				phy-names = "usb2-phy", "usb3-phy";
+				dr_mode = "host";
+				snps,dis_u3_susphy_quirk;
+			};
 		};
 
-		saw0: regulator@2089000 {
-			compatible = "qcom,saw2";
-			reg = <0x02089000 0x1000>, <0x02009000 0x1000>;
-			regulator;
+		hs_phy_0: phy@100f8800 {
+			compatible = "qcom,ipq806x-usb-phy-hs";
+			reg = <0x100f8800 0x30>;
+			clocks = <&gcc USB30_0_UTMI_CLK>;
+			clock-names = "ref";
+			#phy-cells = <0>;
+
+			status = "disabled";
 		};
 
-		saw1: regulator@2099000 {
-			compatible = "qcom,saw2";
-			reg = <0x02099000 0x1000>, <0x02009000 0x1000>;
-			regulator;
+		ss_phy_0: phy@100f8830 {
+			compatible = "qcom,ipq806x-usb-phy-ss";
+			reg = <0x100f8830 0x30>;
+			clocks = <&gcc USB30_0_MASTER_CLK>;
+			clock-names = "ref";
+			#phy-cells = <0>;
+
+			status = "disabled";
+		};
+
+		usb3_1: usb3@110f8800 {
+			compatible = "qcom,ipq8064-dwc3", "qcom,dwc3";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			reg = <0x110f8800 0x8000>;
+			clocks = <&gcc USB30_1_MASTER_CLK>;
+			clock-names = "core";
+
+			ranges;
+
+			resets = <&gcc USB30_1_MASTER_RESET>;
+			reset-names = "master";
+
+			status = "disabled";
+
+			dwc3_1: dwc3@11000000 {
+				compatible = "snps,dwc3";
+				reg = <0x11000000 0xcd00>;
+				interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
+				phys = <&hs_phy_1>, <&ss_phy_1>;
+				phy-names = "usb2-phy", "usb3-phy";
+				dr_mode = "host";
+				snps,dis_u3_susphy_quirk;
+			};
+		};
+
+		hs_phy_1: phy@110f8800 {
+			compatible = "qcom,ipq806x-usb-phy-hs";
+			reg = <0x110f8800 0x30>;
+			clocks = <&gcc USB30_1_UTMI_CLK>;
+			clock-names = "ref";
+			#phy-cells = <0>;
+
+			status = "disabled";
+		};
+
+		ss_phy_1: phy@110f8830 {
+			compatible = "qcom,ipq806x-usb-phy-ss";
+			reg = <0x110f8830 0x30>;
+			clocks = <&gcc USB30_1_MASTER_CLK>;
+			clock-names = "ref";
+			#phy-cells = <0>;
+
+			status = "disabled";
+		};
+
+		sdcc3bam: dma-controller@12182000 {
+			compatible = "qcom,bam-v1.3.0";
+			reg = <0x12182000 0x8000>;
+			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc SDC3_H_CLK>;
+			clock-names = "bam_clk";
+			#dma-cells = <1>;
+			qcom,ee = <0>;
+		};
+
+		sdcc1bam: dma-controller@12402000 {
+			compatible = "qcom,bam-v1.3.0";
+			reg = <0x12402000 0x8000>;
+			interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc SDC1_H_CLK>;
+			clock-names = "bam_clk";
+			#dma-cells = <1>;
+			qcom,ee = <0>;
+		};
+
+		amba: amba {
+			compatible = "simple-bus";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			sdcc3: mmc@12180000 {
+				compatible = "arm,pl18x", "arm,primecell";
+				arm,primecell-periphid = <0x00051180>;
+				status = "disabled";
+				reg = <0x12180000 0x2000>;
+				interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "cmd_irq";
+				clocks = <&gcc SDC3_CLK>, <&gcc SDC3_H_CLK>;
+				clock-names = "mclk", "apb_pclk";
+				bus-width = <8>;
+				cap-sd-highspeed;
+				cap-mmc-highspeed;
+				max-frequency = <192000000>;
+				sd-uhs-sdr104;
+				sd-uhs-ddr50;
+				vqmmc-supply = <&vsdcc_fixed>;
+				dmas = <&sdcc3bam 2>, <&sdcc3bam 1>;
+				dma-names = "tx", "rx";
+			};
+
+			sdcc1: mmc@12400000 {
+				status = "disabled";
+				compatible = "arm,pl18x", "arm,primecell";
+				arm,primecell-periphid = <0x00051180>;
+				reg = <0x12400000 0x2000>;
+				interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "cmd_irq";
+				clocks = <&gcc SDC1_CLK>, <&gcc SDC1_H_CLK>;
+				clock-names = "mclk", "apb_pclk";
+				bus-width = <8>;
+				max-frequency = <96000000>;
+				non-removable;
+				cap-sd-highspeed;
+				cap-mmc-highspeed;
+				mmc-ddr-1_8v;
+				vmmc-supply = <&vsdcc_fixed>;
+				dmas = <&sdcc1bam 2>, <&sdcc1bam 1>;
+				dma-names = "tx", "rx";
+			};
+		};
+
+		gsbi1: gsbi@12440000 {
+			compatible = "qcom,gsbi-v1.0.0";
+			reg = <0x12440000 0x100>;
+			cell-index = <1>;
+			clocks = <&gcc GSBI1_H_CLK>;
+			clock-names = "iface";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			syscon-tcsr = <&tcsr>;
+
+			status = "disabled";
+
+			gsbi1_serial: serial@12450000 {
+				compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
+				reg = <0x12450000 0x100>,
+				      <0x12400000 0x03>;
+				interrupts = <GIC_SPI 193 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc GSBI1_UART_CLK>, <&gcc GSBI1_H_CLK>;
+				clock-names = "core", "iface";
+
+				status = "disabled";
+			};
+
+			gsbi1_i2c: i2c@12460000 {
+				compatible = "qcom,i2c-qup-v1.1.1";
+				reg = <0x12460000 0x1000>;
+				interrupts = <GIC_SPI 194 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc GSBI1_QUP_CLK>, <&gcc GSBI1_H_CLK>;
+				clock-names = "core", "iface";
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				status = "disabled";
+			};
 		};
 
 		gsbi2: gsbi@12480000 {
@@ -530,7 +824,7 @@
 				status = "disabled";
 			};
 
-			i2c@124a0000 {
+			gsbi2_i2c: i2c@124a0000 {
 				compatible = "qcom,i2c-qup-v1.1.1";
 				reg = <0x124a0000 0x1000>;
 				interrupts = <GIC_SPI 196 IRQ_TYPE_LEVEL_HIGH>;
@@ -581,6 +875,106 @@
 			};
 		};
 
+		gsbi6: gsbi@16500000 {
+			compatible = "qcom,gsbi-v1.0.0";
+			reg = <0x16500000 0x100>;
+			cell-index = <6>;
+			clocks = <&gcc GSBI6_H_CLK>;
+			clock-names = "iface";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			syscon-tcsr = <&tcsr>;
+
+			status = "disabled";
+
+			gsbi6_i2c: i2c@16580000 {
+				compatible = "qcom,i2c-qup-v1.1.1";
+				reg = <0x16580000 0x1000>;
+				interrupts = <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>;
+
+				clocks = <&gcc GSBI6_QUP_CLK>, <&gcc GSBI6_H_CLK>;
+				clock-names = "core", "iface";
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				status = "disabled";
+			};
+
+			gsbi6_spi: spi@16580000 {
+				compatible = "qcom,spi-qup-v1.1.1";
+				reg = <0x16580000 0x1000>;
+				interrupts = <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>;
+
+				clocks = <&gcc GSBI6_QUP_CLK>, <&gcc GSBI6_H_CLK>;
+				clock-names = "core", "iface";
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				status = "disabled";
+			};
+		};
+
+		gsbi7: gsbi@16600000 {
+			status = "disabled";
+			compatible = "qcom,gsbi-v1.0.0";
+			cell-index = <7>;
+			reg = <0x16600000 0x100>;
+			clocks = <&gcc GSBI7_H_CLK>;
+			clock-names = "iface";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			syscon-tcsr = <&tcsr>;
+
+			gsbi7_serial: serial@16640000 {
+				compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
+				reg = <0x16640000 0x1000>,
+				      <0x16600000 0x1000>;
+				interrupts = <GIC_SPI 158 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc GSBI7_UART_CLK>, <&gcc GSBI7_H_CLK>;
+				clock-names = "core", "iface";
+				status = "disabled";
+			};
+
+			gsbi7_i2c: i2c@16680000 {
+				compatible = "qcom,i2c-qup-v1.1.1";
+				reg = <0x16680000 0x1000>;
+				interrupts = <GIC_SPI 159 IRQ_TYPE_LEVEL_HIGH>;
+
+				clocks = <&gcc GSBI7_QUP_CLK>, <&gcc GSBI7_H_CLK>;
+				clock-names = "core", "iface";
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				status = "disabled";
+			};
+		};
+
+		adm_dma: dma-controller@18300000 {
+			compatible = "qcom,adm";
+			reg = <0x18300000 0x100000>;
+			interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>;
+			#dma-cells = <1>;
+
+			clocks = <&gcc ADM0_CLK>, <&gcc ADM0_PBUS_CLK>;
+			clock-names = "core", "iface";
+
+			resets = <&gcc ADM0_RESET>,
+				 <&gcc ADM0_PBUS_RESET>,
+				 <&gcc ADM0_C0_RESET>,
+				 <&gcc ADM0_C1_RESET>,
+				 <&gcc ADM0_C2_RESET>;
+			reset-names = "clk", "pbus", "c0", "c1", "c2";
+			qcom,ee = <0>;
+
+			status = "disabled";
+		};
+
 		gsbi5: gsbi@1a200000 {
 			compatible = "qcom,gsbi-v1.0.0";
 			cell-index = <5>;
@@ -588,6 +982,7 @@
 			clocks = <&gcc GSBI5_H_CLK>;
 			clock-names = "iface";
 			#address-cells = <1>;
+
 			#size-cells = <1>;
 			ranges;
 			status = "disabled";
@@ -631,27 +1026,9 @@
 			};
 		};
 
-		gsbi7: gsbi@16600000 {
-			status = "disabled";
-			compatible = "qcom,gsbi-v1.0.0";
-			cell-index = <7>;
-			reg = <0x16600000 0x100>;
-			clocks = <&gcc GSBI7_H_CLK>;
-			clock-names = "iface";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges;
-			syscon-tcsr = <&tcsr>;
-
-			gsbi7_serial: serial@16640000 {
-				compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
-				reg = <0x16640000 0x1000>,
-				      <0x16600000 0x1000>;
-				interrupts = <GIC_SPI 158 IRQ_TYPE_LEVEL_HIGH>;
-				clocks = <&gcc GSBI7_UART_CLK>, <&gcc GSBI7_H_CLK>;
-				clock-names = "core", "iface";
-				status = "disabled";
-			};
+		tcsr: syscon@1a400000 {
+			compatible = "qcom,tcsr-ipq8064", "syscon";
+			reg = <0x1a400000 0x100>;
 		};
 
 		rng@1a500000 {
@@ -661,17 +1038,6 @@
 			clock-names = "core";
 		};
 
-		sata_phy: sata-phy@1b400000 {
-			compatible = "qcom,ipq806x-sata-phy";
-			reg = <0x1b400000 0x200>;
-
-			clocks = <&gcc SATA_PHY_CFG_CLK>;
-			clock-names = "cfg";
-
-			#phy-cells = <0>;
-			status = "disabled";
-		};
-
 		nand: nand-controller@1ac00000 {
 			compatible = "qcom,ipq806x-nand";
 			reg = <0x1ac00000 0x800>;
@@ -694,106 +1060,17 @@
 			status = "disabled";
 		};
 
-		sata: sata@29000000 {
-			compatible = "qcom,ipq806x-ahci", "generic-ahci";
-			reg = <0x29000000 0x180>;
-
-			interrupts = <GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH>;
-
-			clocks = <&gcc SFAB_SATA_S_H_CLK>,
-				 <&gcc SATA_H_CLK>,
-				 <&gcc SATA_A_CLK>,
-				 <&gcc SATA_RXOOB_CLK>,
-				 <&gcc SATA_PMALIVE_CLK>;
-			clock-names = "slave_face", "iface", "core",
-					"rxoob", "pmalive";
+		sata_phy: sata-phy@1b400000 {
+			compatible = "qcom,ipq806x-sata-phy";
+			reg = <0x1b400000 0x200>;
 
-			assigned-clocks = <&gcc SATA_RXOOB_CLK>, <&gcc SATA_PMALIVE_CLK>;
-			assigned-clock-rates = <100000000>, <100000000>;
+			clocks = <&gcc SATA_PHY_CFG_CLK>;
+			clock-names = "cfg";
 
-			phys = <&sata_phy>;
-			phy-names = "sata-phy";
+			#phy-cells = <0>;
 			status = "disabled";
 		};
 
-		qcom,ssbi@500000 {
-			compatible = "qcom,ssbi";
-			reg = <0x00500000 0x1000>;
-			qcom,controller-type = "pmic-arbiter";
-		};
-
-		qfprom: qfprom@700000 {
-			compatible = "qcom,qfprom";
-			reg = <0x00700000 0x1000>;
-			#address-cells = <1>;
-			#size-cells = <1>;
-			tsens_calib: calib@400 {
-				reg = <0x400 0xb>;
-			};
-			tsens_calib_backup: calib_backup@410 {
-				reg = <0x410 0xb>;
-			};
-		};
-
-		gcc: clock-controller@900000 {
-			compatible = "qcom,gcc-ipq8064";
-			reg = <0x00900000 0x4000>;
-			#clock-cells = <1>;
-			#reset-cells = <1>;
-			#power-domain-cells = <1>;
-
-			tsens: thermal-sensor@900000 {
-				compatible = "qcom,ipq8064-tsens";
-
-				nvmem-cells = <&tsens_calib>, <&tsens_calib_backup>;
-				nvmem-cell-names = "calib", "calib_backup";
-				interrupts = <GIC_SPI 178 IRQ_TYPE_LEVEL_HIGH>;
-				interrupt-names = "uplow";
-
-				#qcom,sensors = <11>;
-				#thermal-sensor-cells = <1>;
-			};
-		};
-
-		rpm: rpm@108000 {
-			compatible = "qcom,rpm-ipq8064";
-			reg = <0x108000 0x1000>;
-			qcom,ipc = <&l2cc 0x8 2>;
-
-			interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>,
-					<GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>,
-					<GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "ack", "err", "wakeup";
-
-			clocks = <&gcc RPM_MSG_RAM_H_CLK>;
-			clock-names = "ram";
-
-			rpmcc: clock-controller {
-				compatible = "qcom,rpmcc-ipq806x", "qcom,rpmcc";
-				#clock-cells = <1>;
-			};
-		};
-
-		tcsr: syscon@1a400000 {
-			compatible = "qcom,tcsr-ipq8064", "syscon";
-			reg = <0x1a400000 0x100>;
-		};
-
-		l2cc: clock-controller@2011000 {
-			compatible = "qcom,kpss-gcc", "syscon";
-			reg = <0x2011000 0x1000>;
-			clocks = <&gcc PLL8_VOTE>, <&gcc PXO_SRC>;
-			clock-names = "pll8_vote", "pxo";
-			clock-output-names = "acpu_l2_aux";
-		};
-
-		lcc: clock-controller@28000000 {
-			compatible = "qcom,lcc-ipq8064";
-			reg = <0x28000000 0x1000>;
-			#clock-cells = <1>;
-			#reset-cells = <1>;
-		};
-
 		pcie0: pci@1b500000 {
 			compatible = "qcom,pcie-ipq8064";
 			reg = <0x1b500000 0x1000
@@ -808,7 +1085,7 @@
 			#address-cells = <3>;
 			#size-cells = <2>;
 
-			ranges = <0x81000000 0 0x0fe00000 0x0fe00000 0 0x00100000   /* downstream I/O */
+			ranges = <0x81000000 0 0x0fe00000 0x0fe00000 0 0x00010000   /* downstream I/O */
 				  0x82000000 0 0x08000000 0x08000000 0 0x07e00000>; /* non-prefetchable memory */
 
 			interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
@@ -842,7 +1119,7 @@
 			pinctrl-names = "default";
 
 			status = "disabled";
-			perst-gpio = <&qcom_pinmux 3 GPIO_ACTIVE_LOW>;
+			perst-gpios = <&qcom_pinmux 3 GPIO_ACTIVE_LOW>;
 		};
 
 		pcie1: pci@1b700000 {
@@ -859,7 +1136,7 @@
 			#address-cells = <3>;
 			#size-cells = <2>;
 
-			ranges = <0x81000000 0 0x31e00000 0x31e00000 0 0x00100000   /* downstream I/O */
+			ranges = <0x81000000 0 0x31e00000 0x31e00000 0 0x00010000   /* downstream I/O */
 				  0x82000000 0 0x2e000000 0x2e000000 0 0x03e00000>; /* non-prefetchable memory */
 
 			interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
@@ -893,7 +1170,7 @@
 			pinctrl-names = "default";
 
 			status = "disabled";
-			perst-gpio = <&qcom_pinmux 48 GPIO_ACTIVE_LOW>;
+			perst-gpios = <&qcom_pinmux 48 GPIO_ACTIVE_LOW>;
 		};
 
 		pcie2: pci@1b900000 {
@@ -910,7 +1187,7 @@
 			#address-cells = <3>;
 			#size-cells = <2>;
 
-			ranges = <0x81000000 0 0x35e00000 0x35e00000 0 0x00100000   /* downstream I/O */
+			ranges = <0x81000000 0 0x35e00000 0x35e00000 0 0x00010000   /* downstream I/O */
 				  0x82000000 0 0x32000000 0x32000000 0 0x03e00000>; /* non-prefetchable memory */
 
 			interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
@@ -944,12 +1221,7 @@
 			pinctrl-names = "default";
 
 			status = "disabled";
-			perst-gpio = <&qcom_pinmux 63 GPIO_ACTIVE_LOW>;
-		};
-
-		nss_common: syscon@03000000 {
-			compatible = "syscon";
-			reg = <0x03000000 0x0000FFFF>;
+			perst-gpios = <&qcom_pinmux 63 GPIO_ACTIVE_LOW>;
 		};
 
 		qsgmii_csr: syscon@1bb00000 {
@@ -957,22 +1229,60 @@
 			reg = <0x1bb00000 0x000001FF>;
 		};
 
-		stmmac_axi_setup: stmmac-axi-config {
-			snps,wr_osr_lmt = <7>;
-			snps,rd_osr_lmt = <7>;
-			snps,blen = <16 0 0 0 0 0 0>;
+		lcc: clock-controller@28000000 {
+			compatible = "qcom,lcc-ipq8064";
+			reg = <0x28000000 0x1000>;
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+		};
+
+		lpass@28100000 {
+			compatible = "qcom,lpass-cpu";
+			status = "disabled";
+			clocks = <&lcc AHBIX_CLK>,
+					<&lcc MI2S_OSR_CLK>,
+					<&lcc MI2S_BIT_CLK>;
+			clock-names = "ahbix-clk",
+					"mi2s-osr-clk",
+					"mi2s-bit-clk";
+			interrupts = <GIC_SPI 85 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "lpass-irq-lpaif";
+			reg = <0x28100000 0x10000>;
+			reg-names = "lpass-lpaif";
+		};
+
+		sata: sata@29000000 {
+			compatible = "qcom,ipq806x-ahci", "generic-ahci";
+			reg = <0x29000000 0x180>;
+
+			interrupts = <GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH>;
+
+			clocks = <&gcc SFAB_SATA_S_H_CLK>,
+				 <&gcc SATA_H_CLK>,
+				 <&gcc SATA_A_CLK>,
+				 <&gcc SATA_RXOOB_CLK>,
+				 <&gcc SATA_PMALIVE_CLK>;
+			clock-names = "slave_face", "iface", "core",
+					"rxoob", "pmalive";
+
+			assigned-clocks = <&gcc SATA_RXOOB_CLK>, <&gcc SATA_PMALIVE_CLK>;
+			assigned-clock-rates = <100000000>, <100000000>;
+
+			phys = <&sata_phy>;
+			phy-names = "sata-phy";
+			status = "disabled";
 		};
 
 		gmac0: ethernet@37000000 {
 			device_type = "network";
-			compatible = "qcom,ipq806x-gmac";
+			compatible = "qcom,ipq806x-gmac", "snps,dwmac";
 			reg = <0x37000000 0x200000>;
 			interrupts = <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "macirq";
 
 			snps,axi-config = <&stmmac_axi_setup>;
 			snps,pbl = <32>;
-			snps,aal = <1>;
+			snps,aal;
 
 			qcom,nss-common = <&nss_common>;
 			qcom,qsgmii-csr = <&qsgmii_csr>;
@@ -989,14 +1299,14 @@
 
 		gmac1: ethernet@37200000 {
 			device_type = "network";
-			compatible = "qcom,ipq806x-gmac";
+			compatible = "qcom,ipq806x-gmac", "snps,dwmac";
 			reg = <0x37200000 0x200000>;
 			interrupts = <GIC_SPI 223 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "macirq";
 
 			snps,axi-config = <&stmmac_axi_setup>;
 			snps,pbl = <32>;
-			snps,aal = <1>;
+			snps,aal;
 
 			qcom,nss-common = <&nss_common>;
 			qcom,qsgmii-csr = <&qsgmii_csr>;
@@ -1013,14 +1323,14 @@
 
 		gmac2: ethernet@37400000 {
 			device_type = "network";
-			compatible = "qcom,ipq806x-gmac";
+			compatible = "qcom,ipq806x-gmac", "snps,dwmac";
 			reg = <0x37400000 0x200000>;
 			interrupts = <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "macirq";
 
 			snps,axi-config = <&stmmac_axi_setup>;
 			snps,pbl = <32>;
-			snps,aal = <1>;
+			snps,aal;
 
 			qcom,nss-common = <&nss_common>;
 			qcom,qsgmii-csr = <&qsgmii_csr>;
@@ -1037,14 +1347,14 @@
 
 		gmac3: ethernet@37600000 {
 			device_type = "network";
-			compatible = "qcom,ipq806x-gmac";
+			compatible = "qcom,ipq806x-gmac", "snps,dwmac";
 			reg = <0x37600000 0x200000>;
 			interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "macirq";
 
 			snps,axi-config = <&stmmac_axi_setup>;
 			snps,pbl = <32>;
-			snps,aal = <1>;
+			snps,aal;
 
 			qcom,nss-common = <&nss_common>;
 			qcom,qsgmii-csr = <&qsgmii_csr>;
@@ -1058,168 +1368,5 @@
 
 			status = "disabled";
 		};
-
-		hs_phy_0: phy@100f8800 {
-			compatible = "qcom,ipq806x-usb-phy-hs";
-			reg = <0x100f8800 0x30>;
-			clocks = <&gcc USB30_0_UTMI_CLK>;
-			clock-names = "ref";
-			#phy-cells = <0>;
-
-			status = "disabled";
-		};
-
-		ss_phy_0: phy@100f8830 {
-			compatible = "qcom,ipq806x-usb-phy-ss";
-			reg = <0x100f8830 0x30>;
-			clocks = <&gcc USB30_0_MASTER_CLK>;
-			clock-names = "ref";
-			#phy-cells = <0>;
-
-			status = "disabled";
-		};
-
-		usb3_0: usb3@100f8800 {
-			compatible = "qcom,dwc3", "syscon";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			reg = <0x100f8800 0x8000>;
-			clocks = <&gcc USB30_0_MASTER_CLK>;
-			clock-names = "core";
-
-			ranges;
-
-			resets = <&gcc USB30_0_MASTER_RESET>;
-			reset-names = "master";
-
-			status = "disabled";
-
-			dwc3_0: dwc3@10000000 {
-				compatible = "snps,dwc3";
-				reg = <0x10000000 0xcd00>;
-				interrupts = <GIC_SPI 205 IRQ_TYPE_LEVEL_HIGH>;
-				phys = <&hs_phy_0>, <&ss_phy_0>;
-				phy-names = "usb2-phy", "usb3-phy";
-				dr_mode = "host";
-				snps,dis_u3_susphy_quirk;
-			};
-		};
-
-		hs_phy_1: phy@110f8800 {
-			compatible = "qcom,ipq806x-usb-phy-hs";
-			reg = <0x110f8800 0x30>;
-			clocks = <&gcc USB30_1_UTMI_CLK>;
-			clock-names = "ref";
-			#phy-cells = <0>;
-		};
-
-		ss_phy_1: phy@110f8830 {
-			compatible = "qcom,ipq806x-usb-phy-ss";
-			reg = <0x110f8830 0x30>;
-			clocks = <&gcc USB30_1_MASTER_CLK>;
-			clock-names = "ref";
-			#phy-cells = <0>;
-		};
-
-		usb3_1: usb3@110f8800 {
-			compatible = "qcom,dwc3", "syscon";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			reg = <0x110f8800 0x8000>;
-			clocks = <&gcc USB30_1_MASTER_CLK>;
-			clock-names = "core";
-
-			ranges;
-
-			resets = <&gcc USB30_1_MASTER_RESET>;
-			reset-names = "master";
-
-			status = "disabled";
-
-			dwc3_1: dwc3@11000000 {
-				compatible = "snps,dwc3";
-				reg = <0x11000000 0xcd00>;
-				interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
-				phys = <&hs_phy_1>, <&ss_phy_1>;
-				phy-names = "usb2-phy", "usb3-phy";
-				dr_mode = "host";
-				snps,dis_u3_susphy_quirk;
-			};
-		};
-
-		vsdcc_fixed: vsdcc-regulator {
-			compatible = "regulator-fixed";
-			regulator-name = "SDCC Power";
-			regulator-min-microvolt = <3300000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-always-on;
-		};
-
-		sdcc1bam: dma@12402000 {
-			compatible = "qcom,bam-v1.3.0";
-			reg = <0x12402000 0x8000>;
-			interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc SDC1_H_CLK>;
-			clock-names = "bam_clk";
-			#dma-cells = <1>;
-			qcom,ee = <0>;
-		};
-
-		sdcc3bam: dma@12182000 {
-			compatible = "qcom,bam-v1.3.0";
-			reg = <0x12182000 0x8000>;
-			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc SDC3_H_CLK>;
-			clock-names = "bam_clk";
-			#dma-cells = <1>;
-			qcom,ee = <0>;
-		};
-
-		amba: amba {
-			compatible = "simple-bus";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges;
-
-			sdcc1: mmc@12400000 {
-				status          = "disabled";
-				compatible      = "arm,pl18x", "arm,primecell";
-				arm,primecell-periphid = <0x00051180>;
-				reg             = <0x12400000 0x2000>;
-				interrupts      = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
-				interrupt-names = "cmd_irq";
-				clocks          = <&gcc SDC1_CLK>, <&gcc SDC1_H_CLK>;
-				clock-names     = "mclk", "apb_pclk";
-				bus-width       = <8>;
-				max-frequency   = <96000000>;
-				non-removable;
-				cap-sd-highspeed;
-				cap-mmc-highspeed;
-				mmc-ddr-1_8v;
-				vmmc-supply = <&vsdcc_fixed>;
-				dmas = <&sdcc1bam 2>, <&sdcc1bam 1>;
-				dma-names = "tx", "rx";
-			};
-
-			sdcc3: mmc@12180000 {
-				compatible      = "arm,pl18x", "arm,primecell";
-				arm,primecell-periphid = <0x00051180>;
-				status          = "disabled";
-				reg             = <0x12180000 0x2000>;
-				interrupts      = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
-				interrupt-names = "cmd_irq";
-				clocks          = <&gcc SDC3_CLK>, <&gcc SDC3_H_CLK>;
-				clock-names     = "mclk", "apb_pclk";
-				bus-width       = <8>;
-				cap-sd-highspeed;
-				cap-mmc-highspeed;
-				max-frequency   = <192000000>;
-				sd-uhs-sdr104;
-				sd-uhs-ddr50;
-				vqmmc-supply = <&vsdcc_fixed>;
-				dmas = <&sdcc3bam 2>, <&sdcc3bam 1>;
-				dma-names = "tx", "rx";
-			};
-		};
 	};
 };
diff --git a/arch/arm/boot/dts/qcom-ipq8065-smb208.dtsi b/arch/arm/boot/dts/qcom-ipq8065-smb208.dtsi
new file mode 100644
index 000000000000..803e6ff99ef8
--- /dev/null
+++ b/arch/arm/boot/dts/qcom-ipq8065-smb208.dtsi
@@ -0,0 +1,37 @@
+// SPDX-License-Identifier: GPL-2.0
+
+#include "qcom-ipq8065.dtsi"
+
+&rpm {
+	smb208_regulators: regulators {
+		compatible = "qcom,rpm-smb208-regulators";
+
+		smb208_s1a: s1a {
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1150000>;
+
+			qcom,switch-mode-frequency = <1200000>;
+		};
+
+		smb208_s1b: s1b {
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1150000>;
+
+			qcom,switch-mode-frequency = <1200000>;
+		};
+
+		smb208_s2a: s2a {
+			regulator-min-microvolt = <775000>;
+			regulator-max-microvolt = <1275000>;
+
+			qcom,switch-mode-frequency = <1200000>;
+		};
+
+		smb208_s2b: s2b {
+			regulator-min-microvolt = <775000>;
+			regulator-max-microvolt = <1275000>;
+
+			qcom,switch-mode-frequency = <1200000>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/qcom-ipq8065.dtsi b/arch/arm/boot/dts/qcom-ipq8065.dtsi
new file mode 100644
index 000000000000..ea49f6cc416d
--- /dev/null
+++ b/arch/arm/boot/dts/qcom-ipq8065.dtsi
@@ -0,0 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0
+
+#include "qcom-ipq8064-v2.0.dtsi"
+
+/ {
+	model = "Qualcomm Technologies, Inc. IPQ8065";
+	compatible = "qcom,ipq8065", "qcom,ipq8064";
+};
diff --git a/arch/arm/boot/dts/qcom-mdm9615-wp8548-mangoh-green.dts b/arch/arm/boot/dts/qcom-mdm9615-wp8548-mangoh-green.dts
index 942e3a2cac35..0827de5426c1 100644
--- a/arch/arm/boot/dts/qcom-mdm9615-wp8548-mangoh-green.dts
+++ b/arch/arm/boot/dts/qcom-mdm9615-wp8548-mangoh-green.dts
@@ -103,7 +103,7 @@
 
 &gsbi3_spi {
 	spi@0 {
-		compatible = "swir,mangoh-iotport-spi", "spidev";
+		compatible = "swir,mangoh-iotport-spi";
 		spi-max-frequency = <24000000>;
 		reg = <0>;
 	};
diff --git a/arch/arm/boot/dts/qcom-mdm9615-wp8548.dtsi b/arch/arm/boot/dts/qcom-mdm9615-wp8548.dtsi
index 10ad929759ed..49de1821ac3a 100644
--- a/arch/arm/boot/dts/qcom-mdm9615-wp8548.dtsi
+++ b/arch/arm/boot/dts/qcom-mdm9615-wp8548.dtsi
@@ -114,7 +114,7 @@
 };
 
 &pmicgpio {
-	usb_vbus_5v_pins: usb_vbus_5v_pins {
+	usb_vbus_5v_pins: usb-vbus-5v-state {
 		pins = "gpio4";
 		function = "normal";
 		output-high;
diff --git a/arch/arm/boot/dts/qcom-mdm9615.dtsi b/arch/arm/boot/dts/qcom-mdm9615.dtsi
index c32415f0e66d..b47c86412de2 100644
--- a/arch/arm/boot/dts/qcom-mdm9615.dtsi
+++ b/arch/arm/boot/dts/qcom-mdm9615.dtsi
@@ -139,6 +139,7 @@
 		gcc: clock-controller@900000 {
 			compatible = "qcom,gcc-mdm9615";
 			#clock-cells = <1>;
+			#power-domain-cells = <1>;
 			#reset-cells = <1>;
 			reg = <0x900000 0x4000>;
 		};
@@ -151,7 +152,7 @@
 		};
 
 		l2cc: clock-controller@2011000 {
-			compatible = "syscon";
+			compatible = "qcom,kpss-gcc", "syscon";
 			reg = <0x02011000 0x1000>;
 		};
 
@@ -320,6 +321,7 @@
 
 				pmicgpio: gpio@150 {
 					compatible = "qcom,pm8018-gpio", "qcom,ssbi-gpio";
+					reg = <0x150>;
 					interrupt-controller;
 					#interrupt-cells = <2>;
 					gpio-controller;
@@ -329,7 +331,7 @@
 			};
 		};
 
-		sdcc1bam: dma@12182000{
+		sdcc1bam: dma-controller@12182000{
 			compatible = "qcom,bam-v1.3.0";
 			reg = <0x12182000 0x8000>;
 			interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
@@ -339,7 +341,7 @@
 			qcom,ee = <0>;
 		};
 
-		sdcc2bam: dma@12142000{
+		sdcc2bam: dma-controller@12142000{
 			compatible = "qcom,bam-v1.3.0";
 			reg = <0x12142000 0x8000>;
 			interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
@@ -360,7 +362,7 @@
 				arm,primecell-periphid = <0x00051180>;
 				reg = <0x12180000 0x2000>;
 				interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
-				interrupt-names	= "cmd_irq";
+				interrupt-names = "cmd_irq";
 				clocks = <&gcc SDC1_CLK>, <&gcc SDC1_H_CLK>;
 				clock-names = "mclk", "apb_pclk";
 				bus-width = <8>;
@@ -380,7 +382,7 @@
 				status = "disabled";
 				reg = <0x12140000 0x2000>;
 				interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
-				interrupt-names	= "cmd_irq";
+				interrupt-names = "cmd_irq";
 				clocks = <&gcc SDC2_CLK>, <&gcc SDC2_H_CLK>;
 				clock-names = "mclk", "apb_pclk";
 				bus-width = <4>;
@@ -410,7 +412,7 @@
 			interrupts = <GIC_SPI 19 IRQ_TYPE_EDGE_RISING>,
 				     <GIC_SPI 21 IRQ_TYPE_EDGE_RISING>,
 				     <GIC_SPI 22 IRQ_TYPE_EDGE_RISING>;
-			interrupt-names	= "ack", "err", "wakeup";
+			interrupt-names = "ack", "err", "wakeup";
 
 			regulators {
 				compatible = "qcom,rpm-pm8018-regulators";
diff --git a/arch/arm/boot/dts/qcom-msm8226-samsung-s3ve3g.dts b/arch/arm/boot/dts/qcom-msm8226-samsung-s3ve3g.dts
index d159188c8b95..290e1df631f0 100644
--- a/arch/arm/boot/dts/qcom-msm8226-samsung-s3ve3g.dts
+++ b/arch/arm/boot/dts/qcom-msm8226-samsung-s3ve3g.dts
@@ -18,8 +18,6 @@
 	};
 };
 
-&soc {
-	serial@f991f000 {
-		status = "ok";
-	};
+&blsp1_uart3 {
+	status = "ok";
 };
diff --git a/arch/arm/boot/dts/qcom-msm8226.dtsi b/arch/arm/boot/dts/qcom-msm8226.dtsi
index 7d48599502b3..cf2d56929428 100644
--- a/arch/arm/boot/dts/qcom-msm8226.dtsi
+++ b/arch/arm/boot/dts/qcom-msm8226.dtsi
@@ -8,6 +8,8 @@
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/clock/qcom,gcc-msm8974.h>
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/power/qcom-rpmpd.h>
+#include <dt-bindings/reset/qcom,gcc-msm8974.h>
 
 / {
 	#address-cells = <1>;
@@ -43,13 +45,6 @@
 		};
 	};
 
-	tcsr_mutex: hwlock {
-		compatible = "qcom,tcsr-mutex";
-		syscon = <&tcsr_mutex_block 0 0x80>;
-
-		#hwlock-cells = <1>;
-	};
-
 	reserved-memory {
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -59,6 +54,11 @@
 			reg = <0x3000000 0x100000>;
 			no-map;
 		};
+
+		adsp_region: adsp@dc00000 {
+			reg = <0x0dc00000 0x1900000>;
+			no-map;
+		};
 	};
 
 	smd {
@@ -72,6 +72,35 @@
 			rpm_requests: rpm-requests {
 				compatible = "qcom,rpm-msm8226";
 				qcom,smd-channels = "rpm_requests";
+
+				rpmpd: power-controller {
+					compatible = "qcom,msm8226-rpmpd";
+					#power-domain-cells = <1>;
+					operating-points-v2 = <&rpmpd_opp_table>;
+
+					rpmpd_opp_table: opp-table {
+						compatible = "operating-points-v2";
+
+						rpmpd_opp_ret: opp1 {
+							opp-level = <1>;
+						};
+						rpmpd_opp_svs_krait: opp2 {
+							opp-level = <2>;
+						};
+						rpmpd_opp_svs_soc: opp3 {
+							opp-level = <3>;
+						};
+						rpmpd_opp_nom: opp4 {
+							opp-level = <4>;
+						};
+						rpmpd_opp_turbo: opp5 {
+							opp-level = <5>;
+						};
+						rpmpd_opp_super_turbo: opp6 {
+							opp-level = <6>;
+						};
+					};
+				};
 			};
 		};
 	};
@@ -85,6 +114,31 @@
 		hwlocks = <&tcsr_mutex 3>;
 	};
 
+	smp2p-adsp {
+		compatible = "qcom,smp2p";
+		qcom,smem = <443>, <429>;
+
+		interrupt-parent = <&intc>;
+		interrupts = <GIC_SPI 158 IRQ_TYPE_EDGE_RISING>;
+
+		qcom,ipc = <&apcs 8 10>;
+
+		qcom,local-pid = <0>;
+		qcom,remote-pid = <2>;
+
+		adsp_smp2p_out: master-kernel {
+			qcom,entry-name = "master-kernel";
+			#qcom,smem-state-cells = <1>;
+		};
+
+		adsp_smp2p_in: slave-kernel {
+			qcom,entry-name = "slave-kernel";
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
 	soc: soc {
 		compatible = "simple-bus";
 		#address-cells = <1>;
@@ -104,45 +158,60 @@
 			reg = <0xf9011000 0x1000>;
 		};
 
-		sdhc_1: sdhci@f9824900 {
+		sdhc_1: mmc@f9824900 {
 			compatible = "qcom,msm8226-sdhci", "qcom,sdhci-msm-v4";
 			reg = <0xf9824900 0x11c>, <0xf9824000 0x800>;
-			reg-names = "hc_mem", "core_mem";
+			reg-names = "hc", "core";
 			interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "hc_irq", "pwr_irq";
-			clocks = <&gcc GCC_SDCC1_APPS_CLK>,
-				 <&gcc GCC_SDCC1_AHB_CLK>,
+			clocks = <&gcc GCC_SDCC1_AHB_CLK>,
+				 <&gcc GCC_SDCC1_APPS_CLK>,
 				 <&xo_board>;
-			clock-names = "core", "iface", "xo";
+			clock-names = "iface", "core", "xo";
+			pinctrl-names = "default";
+			pinctrl-0 = <&sdhc1_default_state>;
 			status = "disabled";
 		};
 
-		sdhc_2: sdhci@f98a4900 {
+		sdhc_2: mmc@f98a4900 {
 			compatible = "qcom,msm8226-sdhci", "qcom,sdhci-msm-v4";
 			reg = <0xf98a4900 0x11c>, <0xf98a4000 0x800>;
-			reg-names = "hc_mem", "core_mem";
+			reg-names = "hc", "core";
 			interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 221 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "hc_irq", "pwr_irq";
-			clocks = <&gcc GCC_SDCC2_APPS_CLK>,
-				 <&gcc GCC_SDCC2_AHB_CLK>,
+			clocks = <&gcc GCC_SDCC2_AHB_CLK>,
+				 <&gcc GCC_SDCC2_APPS_CLK>,
 				 <&xo_board>;
-			clock-names = "core", "iface", "xo";
+			clock-names = "iface", "core", "xo";
+			pinctrl-names = "default";
+			pinctrl-0 = <&sdhc2_default_state>;
 			status = "disabled";
 		};
 
-		sdhc_3: sdhci@f9864900 {
+		sdhc_3: mmc@f9864900 {
 			compatible = "qcom,msm8226-sdhci", "qcom,sdhci-msm-v4";
 			reg = <0xf9864900 0x11c>, <0xf9864000 0x800>;
-			reg-names = "hc_mem", "core_mem";
+			reg-names = "hc", "core";
 			interrupts = <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 224 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "hc_irq", "pwr_irq";
-			clocks = <&gcc GCC_SDCC3_APPS_CLK>,
-				 <&gcc GCC_SDCC3_AHB_CLK>,
+			clocks = <&gcc GCC_SDCC3_AHB_CLK>,
+				 <&gcc GCC_SDCC3_APPS_CLK>,
 				 <&xo_board>;
-			clock-names = "core", "iface", "xo";
+			clock-names = "iface", "core", "xo";
+			pinctrl-names = "default";
+			pinctrl-0 = <&sdhc3_default_state>;
+			status = "disabled";
+		};
+
+		blsp1_uart1: serial@f991d000 {
+			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+			reg = <0xf991d000 0x1000>;
+			interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_UART1_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
 			status = "disabled";
 		};
 
@@ -229,6 +298,44 @@
 			#size-cells = <0>;
 		};
 
+		usb: usb@f9a55000 {
+			compatible = "qcom,ci-hdrc";
+			reg = <0xf9a55000 0x200>,
+			      <0xf9a55200 0x200>;
+			interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_USB_HS_AHB_CLK>,
+				 <&gcc GCC_USB_HS_SYSTEM_CLK>;
+			clock-names = "iface", "core";
+			assigned-clocks = <&gcc GCC_USB_HS_SYSTEM_CLK>;
+			assigned-clock-rates = <75000000>;
+			resets = <&gcc GCC_USB_HS_BCR>;
+			reset-names = "core";
+			phy_type = "ulpi";
+			dr_mode = "otg";
+			hnp-disable;
+			srp-disable;
+			adp-disable;
+			ahb-burst-config = <0>;
+			phy-names = "usb-phy";
+			phys = <&usb_hs_phy>;
+			status = "disabled";
+			#reset-cells = <1>;
+
+			ulpi {
+				usb_hs_phy: phy {
+					compatible = "qcom,usb-hs-phy-msm8226",
+						     "qcom,usb-hs-phy";
+					#phy-cells = <0>;
+					clocks = <&xo_board>, <&gcc GCC_USB2A_PHY_SLEEP_CLK>;
+					clock-names = "ref", "sleep";
+					resets = <&gcc GCC_USB2A_PHY_BCR>, <&usb 0>;
+					reset-names = "phy", "por";
+					qcom,init-seq = /bits/ 8 <0x0 0x44
+						0x1 0x68 0x2 0x24 0x3 0x13>;
+				};
+			};
+		};
+
 		gcc: clock-controller@fc400000 {
 			compatible = "qcom,gcc-msm8226";
 			reg = <0xfc400000 0x4000>;
@@ -281,6 +388,57 @@
 				drive-strength = <2>;
 				bias-disable;
 			};
+
+			sdhc1_default_state: sdhc1-default-state {
+				clk {
+					pins = "sdc1_clk";
+					drive-strength = <10>;
+					bias-disable;
+				};
+
+				cmd-data {
+					pins = "sdc1_cmd", "sdc1_data";
+					drive-strength = <10>;
+					bias-pull-up;
+				};
+			};
+
+			sdhc2_default_state: sdhc2-default-state {
+				clk {
+					pins = "sdc2_clk";
+					drive-strength = <10>;
+					bias-disable;
+				};
+
+				cmd-data {
+					pins = "sdc2_cmd", "sdc2_data";
+					drive-strength = <10>;
+					bias-pull-up;
+				};
+			};
+
+			sdhc3_default_state: sdhc3-default-state {
+				clk {
+					pins = "gpio44";
+					function = "sdc3";
+					drive-strength = <8>;
+					bias-disable;
+				};
+
+				cmd {
+					pins = "gpio43";
+					function = "sdc3";
+					drive-strength = <8>;
+					bias-pull-up;
+				};
+
+				data {
+					pins = "gpio39", "gpio40", "gpio41", "gpio42";
+					function = "sdc3";
+					drive-strength = <8>;
+					bias-pull-up;
+				};
+			};
 		};
 
 		restart@fc4ab000 {
@@ -374,9 +532,44 @@
 			reg = <0xfc428000 0x4000>;
 		};
 
-		tcsr_mutex_block: syscon@fd484000 {
-			compatible = "syscon";
-			reg = <0xfd484000 0x2000>;
+		tcsr_mutex: hwlock@fd484000 {
+			compatible = "qcom,msm8226-tcsr-mutex", "qcom,tcsr-mutex";
+			reg = <0xfd484000 0x1000>;
+			#hwlock-cells = <1>;
+		};
+
+		adsp: remoteproc@fe200000 {
+			compatible = "qcom,msm8226-adsp-pil";
+			reg = <0xfe200000 0x100>;
+
+			interrupts-extended = <&intc GIC_SPI 162 IRQ_TYPE_EDGE_RISING>,
+					      <&adsp_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
+					      <&adsp_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
+					      <&adsp_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
+					      <&adsp_smp2p_in 3 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "wdog", "fatal", "ready", "handover", "stop-ack";
+
+			power-domains = <&rpmpd MSM8226_VDDCX>;
+			power-domain-names = "cx";
+
+			clocks = <&xo_board>;
+			clock-names = "xo";
+
+			memory-region = <&adsp_region>;
+
+			qcom,smem-states = <&adsp_smp2p_out 0>;
+			qcom,smem-state-names = "stop";
+
+			status = "disabled";
+
+			smd-edge {
+				interrupts = <GIC_SPI 156 IRQ_TYPE_EDGE_RISING>;
+
+				qcom,ipc = <&apcs 8 8>;
+				qcom,smd-edge = <1>;
+
+				label = "lpass";
+			};
 		};
 	};
 
diff --git a/arch/arm/boot/dts/qcom-msm8660-surf.dts b/arch/arm/boot/dts/qcom-msm8660-surf.dts
index 414280d9bdba..be18f1be29a1 100644
--- a/arch/arm/boot/dts/qcom-msm8660-surf.dts
+++ b/arch/arm/boot/dts/qcom-msm8660-surf.dts
@@ -15,38 +15,23 @@
 		stdout-path = "serial0:115200n8";
 	};
 
-	soc {
-		gsbi@19c00000 {
-			status = "okay";
-			qcom,mode = <GSBI_PROT_I2C_UART>;
-			serial@19c40000 {
-				status = "okay";
-			};
-		};
-
-		/* Temporary fixed regulator */
-		vsdcc_fixed: vsdcc-regulator {
-			compatible = "regulator-fixed";
-			regulator-name = "SDCC Power";
-			regulator-min-microvolt = <2700000>;
-			regulator-max-microvolt = <2700000>;
-			regulator-always-on;
-		};
+	/* Temporary fixed regulator */
+	vsdcc_fixed: vsdcc-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "SDCC Power";
+		regulator-min-microvolt = <2700000>;
+		regulator-max-microvolt = <2700000>;
+		regulator-always-on;
+	};
+};
 
-		amba {
-			/* eMMC */
-			sdcc1: mmc@12400000 {
-				status = "okay";
-				vmmc-supply = <&vsdcc_fixed>;
-			};
+&gsbi12 {
+	qcom,mode = <GSBI_PROT_I2C_UART>;
+	status = "okay";
+};
 
-			/* External micro SD card */
-			sdcc3: mmc@12180000 {
-				status = "okay";
-				vmmc-supply = <&vsdcc_fixed>;
-			};
-		};
-	};
+&gsbi12_serial {
+	status = "okay";
 };
 
 &pm8058 {
@@ -76,3 +61,15 @@
 		keypad,num-columns = <5>;
 	};
 };
+
+/* eMMC */
+&sdcc1 {
+	vmmc-supply = <&vsdcc_fixed>;
+	status = "okay";
+};
+
+/* External micro SD card */
+&sdcc3 {
+	vmmc-supply = <&vsdcc_fixed>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/qcom-msm8660.dtsi b/arch/arm/boot/dts/qcom-msm8660.dtsi
index 1e8aab357f9c..ddce7d64ba99 100644
--- a/arch/arm/boot/dts/qcom-msm8660.dtsi
+++ b/arch/arm/boot/dts/qcom-msm8660.dtsi
@@ -50,22 +50,25 @@
 	};
 
 	clocks {
-		cxo_board {
+		cxo_board: cxo-board-clk {
 			compatible = "fixed-clock";
 			#clock-cells = <0>;
 			clock-frequency = <19200000>;
+			clock-output-names = "cxo_board";
 		};
 
-		pxo_board {
+		pxo_board: pxo-board-clk {
 			compatible = "fixed-clock";
 			#clock-cells = <0>;
 			clock-frequency = <27000000>;
+			clock-output-names = "pxo_board";
 		};
 
-		sleep_clk {
+		sleep-clk {
 			compatible = "fixed-clock";
 			#clock-cells = <0>;
 			clock-frequency = <32768>;
+			clock-output-names = "sleep_clk";
 		};
 	};
 
@@ -126,8 +129,62 @@
 		gcc: clock-controller@900000 {
 			compatible = "qcom,gcc-msm8660";
 			#clock-cells = <1>;
+			#power-domain-cells = <1>;
 			#reset-cells = <1>;
 			reg = <0x900000 0x4000>;
+			clocks = <&pxo_board>, <&cxo_board>;
+			clock-names = "pxo", "cxo";
+		};
+
+		gsbi1: gsbi@16000000 {
+			compatible = "qcom,gsbi-v1.0.0";
+			cell-index = <12>;
+			reg = <0x16000000 0x100>;
+			clocks = <&gcc GSBI1_H_CLK>;
+			clock-names = "iface";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			syscon-tcsr = <&tcsr>;
+
+			status = "disabled";
+
+			gsbi1_spi: spi@16080000 {
+				compatible = "qcom,spi-qup-v1.1.1";
+				reg = <0x16080000 0x1000>;
+				interrupts = <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc GSBI1_QUP_CLK>, <&gcc GSBI1_H_CLK>;
+				clock-names = "core", "iface";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+		};
+
+		gsbi3: gsbi@16200000 {
+			compatible = "qcom,gsbi-v1.0.0";
+			cell-index = <12>;
+			reg = <0x16200000 0x100>;
+			clocks = <&gcc GSBI3_H_CLK>;
+			clock-names = "iface";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			syscon-tcsr = <&tcsr>;
+			status = "disabled";
+
+			gsbi3_i2c: i2c@16280000 {
+				compatible = "qcom,i2c-qup-v1.1.1";
+				reg = <0x16280000 0x1000>;
+				interrupts = <GIC_SPI 151 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc GSBI3_QUP_CLK>, <&gcc GSBI3_H_CLK>;
+				clock-names = "core", "iface";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
 		};
 
 		gsbi6: gsbi@16500000 {
@@ -211,6 +268,7 @@
 			ranges;
 
 			syscon-tcsr = <&tcsr>;
+			status = "disabled";
 
 			gsbi8_i2c: i2c@19880000 {
 				compatible = "qcom,i2c-qup-v1.1.1";
@@ -390,25 +448,27 @@
 		};
 
 		l2cc: clock-controller@2082000 {
-			compatible	= "syscon";
-			reg		= <0x02082000 0x1000>;
+			compatible = "qcom,kpss-gcc", "syscon";
+			reg = <0x02082000 0x1000>;
 		};
 
 		rpm: rpm@104000 {
-			compatible	= "qcom,rpm-msm8660";
-			reg		= <0x00104000 0x1000>;
-			qcom,ipc	= <&l2cc 0x8 2>;
-
-			interrupts	= <GIC_SPI 19 IRQ_TYPE_EDGE_RISING>,
-					  <GIC_SPI 21 IRQ_TYPE_EDGE_RISING>,
-					  <GIC_SPI 22 IRQ_TYPE_EDGE_RISING>;
-			interrupt-names	= "ack", "err", "wakeup";
+			compatible = "qcom,rpm-msm8660";
+			reg = <0x00104000 0x1000>;
+			qcom,ipc = <&l2cc 0x8 2>;
+
+			interrupts = <GIC_SPI 19 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 21 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 22 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "ack", "err", "wakeup";
 			clocks = <&gcc RPM_MSG_RAM_H_CLK>;
 			clock-names = "ram";
 
 			rpmcc: clock-controller {
-				compatible	= "qcom,rpmcc-msm8660", "qcom,rpmcc";
+				compatible = "qcom,rpmcc-msm8660", "qcom,rpmcc";
 				#clock-cells = <1>;
+				clocks = <&pxo_board>;
+				clock-names = "pxo";
 			};
 
 			pm8901-regulators {
@@ -484,80 +544,80 @@
 			#size-cells = <1>;
 			ranges;
 			sdcc1: mmc@12400000 {
-				status		= "disabled";
-				compatible	= "arm,pl18x", "arm,primecell";
+				status = "disabled";
+				compatible = "arm,pl18x", "arm,primecell";
 				arm,primecell-periphid = <0x00051180>;
-				reg		= <0x12400000 0x8000>;
-				interrupts	= <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
-				interrupt-names	= "cmd_irq";
-				clocks		= <&gcc SDC1_CLK>, <&gcc SDC1_H_CLK>;
-				clock-names	= "mclk", "apb_pclk";
-				bus-width	= <8>;
-				max-frequency	= <48000000>;
+				reg = <0x12400000 0x8000>;
+				interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "cmd_irq";
+				clocks = <&gcc SDC1_CLK>, <&gcc SDC1_H_CLK>;
+				clock-names = "mclk", "apb_pclk";
+				bus-width = <8>;
+				max-frequency = <48000000>;
 				non-removable;
 				cap-sd-highspeed;
 				cap-mmc-highspeed;
 			};
 
 			sdcc2: mmc@12140000 {
-				status		= "disabled";
-				compatible	= "arm,pl18x", "arm,primecell";
+				status = "disabled";
+				compatible = "arm,pl18x", "arm,primecell";
 				arm,primecell-periphid = <0x00051180>;
-				reg		= <0x12140000 0x8000>;
-				interrupts	= <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
-				interrupt-names	= "cmd_irq";
-				clocks		= <&gcc SDC2_CLK>, <&gcc SDC2_H_CLK>;
-				clock-names	= "mclk", "apb_pclk";
-				bus-width	= <8>;
-				max-frequency	= <48000000>;
+				reg = <0x12140000 0x8000>;
+				interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "cmd_irq";
+				clocks = <&gcc SDC2_CLK>, <&gcc SDC2_H_CLK>;
+				clock-names = "mclk", "apb_pclk";
+				bus-width = <8>;
+				max-frequency = <48000000>;
 				cap-sd-highspeed;
 				cap-mmc-highspeed;
 			};
 
 			sdcc3: mmc@12180000 {
-				compatible	= "arm,pl18x", "arm,primecell";
+				compatible = "arm,pl18x", "arm,primecell";
 				arm,primecell-periphid = <0x00051180>;
-				status		= "disabled";
-				reg		= <0x12180000 0x8000>;
-				interrupts	= <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
-				interrupt-names	= "cmd_irq";
-				clocks		= <&gcc SDC3_CLK>, <&gcc SDC3_H_CLK>;
-				clock-names	= "mclk", "apb_pclk";
-				bus-width	= <4>;
+				status = "disabled";
+				reg = <0x12180000 0x8000>;
+				interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "cmd_irq";
+				clocks = <&gcc SDC3_CLK>, <&gcc SDC3_H_CLK>;
+				clock-names = "mclk", "apb_pclk";
+				bus-width = <4>;
 				cap-sd-highspeed;
 				cap-mmc-highspeed;
-				max-frequency	= <48000000>;
+				max-frequency = <48000000>;
 				no-1-8-v;
 			};
 
 			sdcc4: mmc@121c0000 {
-				compatible	= "arm,pl18x", "arm,primecell";
+				compatible = "arm,pl18x", "arm,primecell";
 				arm,primecell-periphid = <0x00051180>;
-				status		= "disabled";
-				reg		= <0x121c0000 0x8000>;
-				interrupts	= <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
-				interrupt-names	= "cmd_irq";
-				clocks		= <&gcc SDC4_CLK>, <&gcc SDC4_H_CLK>;
-				clock-names	= "mclk", "apb_pclk";
-				bus-width	= <4>;
-				max-frequency	= <48000000>;
+				status = "disabled";
+				reg = <0x121c0000 0x8000>;
+				interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "cmd_irq";
+				clocks = <&gcc SDC4_CLK>, <&gcc SDC4_H_CLK>;
+				clock-names = "mclk", "apb_pclk";
+				bus-width = <4>;
+				max-frequency = <48000000>;
 				cap-sd-highspeed;
 				cap-mmc-highspeed;
 			};
 
 			sdcc5: mmc@12200000 {
-				compatible	= "arm,pl18x", "arm,primecell";
+				compatible = "arm,pl18x", "arm,primecell";
 				arm,primecell-periphid = <0x00051180>;
-				status		= "disabled";
-				reg		= <0x12200000 0x8000>;
-				interrupts	= <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>;
-				interrupt-names	= "cmd_irq";
-				clocks		= <&gcc SDC5_CLK>, <&gcc SDC5_H_CLK>;
-				clock-names	= "mclk", "apb_pclk";
-				bus-width	= <4>;
+				status = "disabled";
+				reg = <0x12200000 0x8000>;
+				interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "cmd_irq";
+				clocks = <&gcc SDC5_CLK>, <&gcc SDC5_H_CLK>;
+				clock-names = "mclk", "apb_pclk";
+				bus-width = <4>;
 				cap-sd-highspeed;
 				cap-mmc-highspeed;
-				max-frequency	= <48000000>;
+				max-frequency = <48000000>;
 			};
 		};
 
diff --git a/arch/arm/boot/dts/qcom-msm8916-samsung-e5.dts b/arch/arm/boot/dts/qcom-msm8916-samsung-e5.dts
new file mode 100644
index 000000000000..c8d34de8a71e
--- /dev/null
+++ b/arch/arm/boot/dts/qcom-msm8916-samsung-e5.dts
@@ -0,0 +1,3 @@
+// SPDX-License-Identifier: GPL-2.0-only
+#include "arm64/qcom/msm8916-samsung-e5.dts"
+#include "qcom-msm8916-smp.dtsi"
diff --git a/arch/arm/boot/dts/qcom-msm8916-samsung-e7.dts b/arch/arm/boot/dts/qcom-msm8916-samsung-e7.dts
new file mode 100644
index 000000000000..85be286c8608
--- /dev/null
+++ b/arch/arm/boot/dts/qcom-msm8916-samsung-e7.dts
@@ -0,0 +1,3 @@
+// SPDX-License-Identifier: GPL-2.0-only
+#include "arm64/qcom/msm8916-samsung-e7.dts"
+#include "qcom-msm8916-smp.dtsi"
diff --git a/arch/arm/boot/dts/qcom-msm8916-samsung-grandmax.dts b/arch/arm/boot/dts/qcom-msm8916-samsung-grandmax.dts
new file mode 100644
index 000000000000..d3abe0536238
--- /dev/null
+++ b/arch/arm/boot/dts/qcom-msm8916-samsung-grandmax.dts
@@ -0,0 +1,3 @@
+// SPDX-License-Identifier: GPL-2.0-only
+#include "arm64/qcom/msm8916-samsung-grandmax.dts"
+#include "qcom-msm8916-smp.dtsi"
diff --git a/arch/arm/boot/dts/qcom-msm8960-cdp.dts b/arch/arm/boot/dts/qcom-msm8960-cdp.dts
index 4af01039c3b2..9157e3c4f48f 100644
--- a/arch/arm/boot/dts/qcom-msm8960-cdp.dts
+++ b/arch/arm/boot/dts/qcom-msm8960-cdp.dts
@@ -15,318 +15,6 @@
 		stdout-path = "serial0:115200n8";
 	};
 
-	soc {
-		gsbi@16400000 {
-			status = "okay";
-			qcom,mode = <GSBI_PROT_I2C_UART>;
-			serial@16440000 {
-				status = "okay";
-			};
-		};
-
-		amba {
-			/* eMMC */
-			sdcc1: mmc@12400000 {
-				status = "okay";
-			};
-
-			/* External micro SD card */
-			sdcc3: mmc@12180000 {
-				status = "okay";
-			};
-		};
-
-		rpm@108000 {
-			regulators {
-				compatible = "qcom,rpm-pm8921-regulators";
-				vin_lvs1_3_6-supply = <&pm8921_s4>;
-				vin_lvs2-supply = <&pm8921_s4>;
-				vin_lvs4_5_7-supply = <&pm8921_s4>;
-				vdd_ncp-supply = <&pm8921_l6>;
-				vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
-				vdd_l21_l23_l29-supply = <&pm8921_s8>;
-				vdd_l24-supply = <&pm8921_s1>;
-				vdd_l25-supply = <&pm8921_s1>;
-				vdd_l27-supply = <&pm8921_s7>;
-				vdd_l28-supply = <&pm8921_s7>;
-
-				/* Buck SMPS */
-				pm8921_s1: s1 {
-					regulator-always-on;
-					regulator-min-microvolt = <1225000>;
-					regulator-max-microvolt = <1225000>;
-					qcom,switch-mode-frequency = <3200000>;
-					bias-pull-down;
-				};
-
-				pm8921_s2: s2 {
-					regulator-min-microvolt = <1300000>;
-					regulator-max-microvolt = <1300000>;
-					qcom,switch-mode-frequency = <1600000>;
-					bias-pull-down;
-				};
-
-				pm8921_s3: s3 {
-					regulator-min-microvolt = <500000>;
-					regulator-max-microvolt = <1150000>;
-					qcom,switch-mode-frequency = <4800000>;
-					bias-pull-down;
-				};
-
-				pm8921_s4: s4 {
-					regulator-always-on;
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					qcom,switch-mode-frequency = <1600000>;
-					bias-pull-down;
-					qcom,force-mode = <QCOM_RPM_FORCE_MODE_AUTO>;
-				};
-
-				pm8921_s7: s7 {
-					regulator-min-microvolt = <1150000>;
-					regulator-max-microvolt = <1150000>;
-					qcom,switch-mode-frequency = <3200000>;
-					bias-pull-down;
-				};
-
-				pm8921_s8: s8 {
-					regulator-always-on;
-					regulator-min-microvolt = <2050000>;
-					regulator-max-microvolt = <2050000>;
-					qcom,switch-mode-frequency = <1600000>;
-					bias-pull-down;
-				};
-
-				/* PMOS LDO */
-				pm8921_l1: l1 {
-					regulator-always-on;
-					regulator-min-microvolt = <1050000>;
-					regulator-max-microvolt = <1050000>;
-					bias-pull-down;
-				};
-
-				pm8921_l2: l2 {
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <1200000>;
-					bias-pull-down;
-				};
-
-				pm8921_l3: l3 {
-					regulator-min-microvolt = <3075000>;
-					regulator-max-microvolt = <3075000>;
-					bias-pull-down;
-				};
-
-				pm8921_l4: l4 {
-					regulator-always-on;
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					bias-pull-down;
-				};
-
-				pm8921_l5: l5 {
-					regulator-min-microvolt = <2950000>;
-					regulator-max-microvolt = <2950000>;
-					bias-pull-down;
-				};
-
-				pm8921_l6: l6 {
-					regulator-min-microvolt = <2950000>;
-					regulator-max-microvolt = <2950000>;
-					bias-pull-down;
-				};
-
-				pm8921_l7: l7 {
-					regulator-always-on;
-					regulator-min-microvolt = <1850000>;
-					regulator-max-microvolt = <2950000>;
-					bias-pull-down;
-				};
-
-				pm8921_l8: l8 {
-					regulator-min-microvolt = <2800000>;
-					regulator-max-microvolt = <3000000>;
-					bias-pull-down;
-				};
-
-				pm8921_l9: l9 {
-					regulator-min-microvolt = <3000000>;
-					regulator-max-microvolt = <3000000>;
-					bias-pull-down;
-				};
-
-				pm8921_l10: l10 {
-					regulator-min-microvolt = <3000000>;
-					regulator-max-microvolt = <3000000>;
-					bias-pull-down;
-				};
-
-				pm8921_l11: l11 {
-					regulator-min-microvolt = <2850000>;
-					regulator-max-microvolt = <2850000>;
-					bias-pull-down;
-				};
-
-				pm8921_l12: l12 {
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <1200000>;
-					bias-pull-down;
-				};
-
-				pm8921_l14: l14 {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					bias-pull-down;
-				};
-
-				pm8921_l15: l15 {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <2950000>;
-					bias-pull-down;
-				};
-
-				pm8921_l16: l16 {
-					regulator-min-microvolt = <2800000>;
-					regulator-max-microvolt = <2800000>;
-					bias-pull-down;
-				};
-
-				pm8921_l17: l17 {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <2950000>;
-					bias-pull-down;
-				};
-
-				pm8921_l18: l18 {
-					regulator-min-microvolt = <1300000>;
-					regulator-max-microvolt = <1300000>;
-					bias-pull-down;
-				};
-
-				pm8921_l21: l21 {
-					regulator-min-microvolt = <1900000>;
-					regulator-max-microvolt = <1900000>;
-					bias-pull-down;
-				};
-
-				pm8921_l22: l22 {
-					regulator-min-microvolt = <2750000>;
-					regulator-max-microvolt = <2750000>;
-					bias-pull-down;
-				};
-
-				pm8921_l23: l23 {
-					regulator-always-on;
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					bias-pull-down;
-				};
-
-				pm8921_l24: l24 {
-					regulator-min-microvolt = <750000>;
-					regulator-max-microvolt = <1150000>;
-					bias-pull-down;
-				};
-
-				pm8921_l25: l25 {
-					regulator-always-on;
-					regulator-min-microvolt = <1250000>;
-					regulator-max-microvolt = <1250000>;
-					bias-pull-down;
-				};
-
-				/* Low Voltage Switch */
-				pm8921_lvs1: lvs1 {
-					bias-pull-down;
-				};
-
-				pm8921_lvs2: lvs2 {
-					bias-pull-down;
-				};
-
-				pm8921_lvs3: lvs3 {
-					bias-pull-down;
-				};
-
-				pm8921_lvs4: lvs4 {
-					bias-pull-down;
-				};
-
-				pm8921_lvs5: lvs5 {
-					bias-pull-down;
-				};
-
-				pm8921_lvs6: lvs6 {
-					bias-pull-down;
-				};
-
-				pm8921_lvs7: lvs7 {
-					bias-pull-down;
-				};
-
-				pm8921_ncp: ncp {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-					qcom,switch-mode-frequency = <1600000>;
-				};
-			};
-		};
-
-		gsbi@16000000 {
-			status = "okay";
-			qcom,mode = <GSBI_PROT_SPI>;
-			pinctrl-names = "default";
-			pinctrl-0 = <&spi1_default>;
-			spi@16080000 {
-				status = "okay";
-				eth@0 {
-					compatible = "micrel,ks8851";
-					reg = <0>;
-					interrupt-parent = <&msmgpio>;
-					interrupts = <90 8>;
-					spi-max-frequency = <5400000>;
-					vdd-supply = <&ext_l2>;
-					vdd-io-supply = <&pm8921_lvs6>;
-					reset-gpios = <&msmgpio 89 0>;
-				};
-			};
-		};
-
-		pinctrl@800000 {
-			spi1_default: spi1_default {
-				mux {
-					pins = "gpio6", "gpio7", "gpio9";
-					function = "gsbi1";
-				};
-
-				mosi {
-					pins = "gpio6";
-					drive-strength = <12>;
-					bias-disable;
-				};
-
-				miso {
-					pins = "gpio7";
-					drive-strength = <12>;
-					bias-disable;
-				};
-
-				cs {
-					pins = "gpio8";
-					drive-strength = <12>;
-					bias-disable;
-					output-low;
-				};
-
-				clk {
-					pins = "gpio9";
-					drive-strength = <12>;
-					bias-disable;
-				};
-			};
-		};
-	};
-
 	regulators {
 		compatible = "simple-bus";
 
@@ -340,6 +28,71 @@
 	};
 };
 
+&gsbi1 {
+	qcom,mode = <GSBI_PROT_SPI>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi1_default>;
+	status = "okay";
+};
+
+&gsbi1_spi {
+	status = "okay";
+
+	ethernet@0 {
+		compatible = "micrel,ks8851";
+		reg = <0>;
+		interrupt-parent = <&msmgpio>;
+		interrupts = <90 8>;
+		spi-max-frequency = <5400000>;
+		vdd-supply = <&ext_l2>;
+		vdd-io-supply = <&pm8921_lvs6>;
+		reset-gpios = <&msmgpio 89 0>;
+	};
+};
+
+&gsbi5 {
+	qcom,mode = <GSBI_PROT_I2C_UART>;
+	status = "okay";
+};
+
+&gsbi5_serial {
+	status = "okay";
+};
+
+&msmgpio {
+	spi1_default: spi1_default {
+		 mux {
+			pins = "gpio6", "gpio7", "gpio9";
+			function = "gsbi1";
+		 };
+
+		 mosi {
+			pins = "gpio6";
+			drive-strength = <12>;
+			bias-disable;
+		 };
+
+		 miso {
+			pins = "gpio7";
+			drive-strength = <12>;
+			bias-disable;
+		 };
+
+		 cs {
+			pins = "gpio8";
+			drive-strength = <12>;
+			bias-disable;
+			output-low;
+		 };
+
+		 clk {
+			pins = "gpio9";
+			drive-strength = <12>;
+			bias-disable;
+		 };
+	};
+};
+
 &pmicintc {
 	keypad@148 {
 		linux,keymap = <
@@ -352,3 +105,249 @@
 		keypad,num-columns = <5>;
 	};
 };
+
+&rpm {
+	regulators {
+		compatible = "qcom,rpm-pm8921-regulators";
+		vin_lvs1_3_6-supply = <&pm8921_s4>;
+		vin_lvs2-supply = <&pm8921_s4>;
+		vin_lvs4_5_7-supply = <&pm8921_s4>;
+		vdd_ncp-supply = <&pm8921_l6>;
+		vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
+		vdd_l21_l23_l29-supply = <&pm8921_s8>;
+		vdd_l24-supply = <&pm8921_s1>;
+		vdd_l25-supply = <&pm8921_s1>;
+		vdd_l27-supply = <&pm8921_s7>;
+		vdd_l28-supply = <&pm8921_s7>;
+
+		/* Buck SMPS */
+		pm8921_s1: s1 {
+			regulator-always-on;
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+			qcom,switch-mode-frequency = <3200000>;
+			bias-pull-down;
+		};
+
+		pm8921_s2: s2 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+			qcom,switch-mode-frequency = <1600000>;
+			bias-pull-down;
+		};
+
+		pm8921_s3: s3 {
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1150000>;
+			qcom,switch-mode-frequency = <4800000>;
+			bias-pull-down;
+		};
+
+		pm8921_s4: s4 {
+			regulator-always-on;
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			qcom,switch-mode-frequency = <1600000>;
+			bias-pull-down;
+			qcom,force-mode = <QCOM_RPM_FORCE_MODE_AUTO>;
+		};
+
+		pm8921_s7: s7 {
+			regulator-min-microvolt = <1150000>;
+			regulator-max-microvolt = <1150000>;
+			qcom,switch-mode-frequency = <3200000>;
+			bias-pull-down;
+		};
+
+		pm8921_s8: s8 {
+			regulator-always-on;
+			regulator-min-microvolt = <2050000>;
+			regulator-max-microvolt = <2050000>;
+			qcom,switch-mode-frequency = <1600000>;
+			bias-pull-down;
+		};
+
+		/* PMOS LDO */
+		pm8921_l1: l1 {
+			regulator-always-on;
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1050000>;
+			bias-pull-down;
+		};
+
+		pm8921_l2: l2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			bias-pull-down;
+		};
+
+		pm8921_l3: l3 {
+			regulator-min-microvolt = <3075000>;
+			regulator-max-microvolt = <3075000>;
+			bias-pull-down;
+		};
+
+		pm8921_l4: l4 {
+			regulator-always-on;
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
+		};
+
+		pm8921_l5: l5 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			bias-pull-down;
+		};
+
+		pm8921_l6: l6 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			bias-pull-down;
+		};
+
+		pm8921_l7: l7 {
+			regulator-always-on;
+			regulator-min-microvolt = <1850000>;
+			regulator-max-microvolt = <2950000>;
+			bias-pull-down;
+		};
+
+		pm8921_l8: l8 {
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <3000000>;
+			bias-pull-down;
+		};
+
+		pm8921_l9: l9 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+			bias-pull-down;
+		};
+
+		pm8921_l10: l10 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+			bias-pull-down;
+		};
+
+		pm8921_l11: l11 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+			bias-pull-down;
+		};
+
+		pm8921_l12: l12 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			bias-pull-down;
+		};
+
+		pm8921_l14: l14 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
+		};
+
+		pm8921_l15: l15 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+			bias-pull-down;
+		};
+
+		pm8921_l16: l16 {
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+			bias-pull-down;
+		};
+
+		pm8921_l17: l17 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+			bias-pull-down;
+		};
+
+		pm8921_l18: l18 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+			bias-pull-down;
+		};
+
+		pm8921_l21: l21 {
+			regulator-min-microvolt = <1900000>;
+			regulator-max-microvolt = <1900000>;
+			bias-pull-down;
+		};
+
+		pm8921_l22: l22 {
+			regulator-min-microvolt = <2750000>;
+			regulator-max-microvolt = <2750000>;
+			bias-pull-down;
+		};
+
+		pm8921_l23: l23 {
+			regulator-always-on;
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			bias-pull-down;
+		};
+
+		pm8921_l24: l24 {
+			regulator-min-microvolt = <750000>;
+			regulator-max-microvolt = <1150000>;
+			bias-pull-down;
+		};
+
+		pm8921_l25: l25 {
+			regulator-always-on;
+			regulator-min-microvolt = <1250000>;
+			regulator-max-microvolt = <1250000>;
+			bias-pull-down;
+		};
+
+		/* Low Voltage Switch */
+		pm8921_lvs1: lvs1 {
+			bias-pull-down;
+		};
+
+		pm8921_lvs2: lvs2 {
+			bias-pull-down;
+		};
+
+		pm8921_lvs3: lvs3 {
+			bias-pull-down;
+		};
+
+		pm8921_lvs4: lvs4 {
+			bias-pull-down;
+		};
+
+		pm8921_lvs5: lvs5 {
+			bias-pull-down;
+		};
+
+		pm8921_lvs6: lvs6 {
+			bias-pull-down;
+		};
+
+		pm8921_lvs7: lvs7 {
+			bias-pull-down;
+		};
+
+		pm8921_ncp: ncp {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			qcom,switch-mode-frequency = <1600000>;
+		};
+	};
+};
+
+/* eMMC */
+&sdcc1 {
+	status = "okay";
+};
+
+/* External micro SD card */
+&sdcc3 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/qcom-msm8960.dtsi b/arch/arm/boot/dts/qcom-msm8960.dtsi
index 2a0ec97a264f..c5740da3754c 100644
--- a/arch/arm/boot/dts/qcom-msm8960.dtsi
+++ b/arch/arm/boot/dts/qcom-msm8960.dtsi
@@ -3,6 +3,7 @@
 
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/clock/qcom,gcc-msm8960.h>
+#include <dt-bindings/clock/qcom,lcc-msm8960.h>
 #include <dt-bindings/mfd/qcom-rpm.h>
 #include <dt-bindings/soc/qcom,gsbi.h>
 
@@ -56,14 +57,14 @@
 	};
 
 	clocks {
-		cxo_board {
+		cxo_board: cxo_board {
 			compatible = "fixed-clock";
 			#clock-cells = <0>;
 			clock-frequency = <19200000>;
 			clock-output-names = "cxo_board";
 		};
 
-		pxo_board {
+		pxo_board: pxo_board {
 			compatible = "fixed-clock";
 			#clock-cells = <0>;
 			clock-frequency = <27000000>;
@@ -78,6 +79,15 @@
 		};
 	};
 
+	/* Temporary fixed regulator */
+	vsdcc_fixed: vsdcc-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "SDCC Power";
+		regulator-min-microvolt = <2700000>;
+		regulator-max-microvolt = <2700000>;
+		regulator-always-on;
+	};
+
 	soc: soc {
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -118,8 +128,13 @@
 		gcc: clock-controller@900000 {
 			compatible = "qcom,gcc-msm8960";
 			#clock-cells = <1>;
+			#power-domain-cells = <1>;
 			#reset-cells = <1>;
 			reg = <0x900000 0x4000>;
+			clocks = <&cxo_board>,
+				 <&pxo_board>,
+				 <&lcc PLL4>;
+			clock-names = "cxo", "pxo", "pll4";
 		};
 
 		lcc: clock-controller@28000000 {
@@ -127,27 +142,60 @@
 			reg = <0x28000000 0x1000>;
 			#clock-cells = <1>;
 			#reset-cells = <1>;
+			clocks = <&pxo_board>,
+				 <&gcc PLL4_VOTE>,
+				 <0>,
+				 <0>, <0>,
+				 <0>, <0>,
+				 <0>;
+			clock-names = "pxo",
+				      "pll4_vote",
+				      "mi2s_codec_clk",
+				      "codec_i2s_mic_codec_clk",
+				      "spare_i2s_mic_codec_clk",
+				      "codec_i2s_spkr_codec_clk",
+				      "spare_i2s_spkr_codec_clk",
+				      "pcm_codec_clk";
 		};
 
 		clock-controller@4000000 {
 			compatible = "qcom,mmcc-msm8960";
 			reg = <0x4000000 0x1000>;
 			#clock-cells = <1>;
+			#power-domain-cells = <1>;
 			#reset-cells = <1>;
+			clocks = <&pxo_board>,
+				 <&gcc PLL3>,
+				 <&gcc PLL8_VOTE>,
+				 <0>,
+				 <0>,
+				 <0>,
+				 <0>,
+				 <0>;
+			clock-names = "pxo",
+				      "pll3",
+				      "pll8_vote",
+				      "dsi1pll",
+				      "dsi1pllbyte",
+				      "dsi2pll",
+				      "dsi2pllbyte",
+				      "hdmipll";
 		};
 
 		l2cc: clock-controller@2011000 {
-			compatible	= "syscon";
-			reg		= <0x2011000 0x1000>;
+			compatible = "qcom,kpss-gcc", "syscon";
+			reg = <0x2011000 0x1000>;
 		};
 
-		rpm@108000 {
-			compatible	= "qcom,rpm-msm8960";
-			reg		= <0x108000 0x1000>;
-			qcom,ipc	= <&l2cc 0x8 2>;
+		rpm: rpm@108000 {
+			compatible = "qcom,rpm-msm8960";
+			reg = <0x108000 0x1000>;
+			qcom,ipc = <&l2cc 0x8 2>;
 
-			interrupts	= <0 19 0>, <0 21 0>, <0 22 0>;
-			interrupt-names	= "ack", "err", "wakeup";
+			interrupts = <GIC_SPI 19 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 21 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 22 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "ack", "err", "wakeup";
 
 			regulators {
 				compatible = "qcom,rpm-pm8921-regulators";
@@ -192,7 +240,7 @@
 				compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
 				reg = <0x16440000 0x1000>,
 				      <0x16400000 0x1000>;
-				interrupts = <0 154 0x0>;
+				interrupts = <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&gcc GSBI5_UART_CLK>, <&gcc GSBI5_H_CLK>;
 				clock-names = "core", "iface";
 				status = "disabled";
@@ -249,31 +297,22 @@
 			clock-names = "core";
 		};
 
-		/* Temporary fixed regulator */
-		vsdcc_fixed: vsdcc-regulator {
-			compatible = "regulator-fixed";
-			regulator-name = "SDCC Power";
-			regulator-min-microvolt = <2700000>;
-			regulator-max-microvolt = <2700000>;
-			regulator-always-on;
-		};
-
 		amba {
 			compatible = "simple-bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges;
 			sdcc1: mmc@12400000 {
-				status		= "disabled";
-				compatible	= "arm,pl18x", "arm,primecell";
+				status = "disabled";
+				compatible = "arm,pl18x", "arm,primecell";
 				arm,primecell-periphid = <0x00051180>;
-				reg		= <0x12400000 0x8000>;
-				interrupts	= <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
-				interrupt-names	= "cmd_irq";
-				clocks		= <&gcc SDC1_CLK>, <&gcc SDC1_H_CLK>;
-				clock-names	= "mclk", "apb_pclk";
-				bus-width	= <8>;
-				max-frequency	= <96000000>;
+				reg = <0x12400000 0x8000>;
+				interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "cmd_irq";
+				clocks = <&gcc SDC1_CLK>, <&gcc SDC1_H_CLK>;
+				clock-names = "mclk", "apb_pclk";
+				bus-width = <8>;
+				max-frequency = <96000000>;
 				non-removable;
 				cap-sd-highspeed;
 				cap-mmc-highspeed;
@@ -281,18 +320,18 @@
 			};
 
 			sdcc3: mmc@12180000 {
-				compatible	= "arm,pl18x", "arm,primecell";
+				compatible = "arm,pl18x", "arm,primecell";
 				arm,primecell-periphid = <0x00051180>;
-				status		= "disabled";
-				reg		= <0x12180000 0x8000>;
-				interrupts	= <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
-				interrupt-names	= "cmd_irq";
-				clocks		= <&gcc SDC3_CLK>, <&gcc SDC3_H_CLK>;
-				clock-names	= "mclk", "apb_pclk";
-				bus-width	= <4>;
+				status = "disabled";
+				reg = <0x12180000 0x8000>;
+				interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "cmd_irq";
+				clocks = <&gcc SDC3_CLK>, <&gcc SDC3_H_CLK>;
+				clock-names = "mclk", "apb_pclk";
+				bus-width = <4>;
 				cap-sd-highspeed;
 				cap-mmc-highspeed;
-				max-frequency	= <192000000>;
+				max-frequency = <192000000>;
 				no-1-8-v;
 				vmmc-supply = <&vsdcc_fixed>;
 			};
@@ -303,7 +342,7 @@
 			reg = <0x1a400000 0x100>;
 		};
 
-		gsbi@16000000 {
+		gsbi1: gsbi@16000000 {
 			compatible = "qcom,gsbi-v1.0.0";
 			cell-index = <1>;
 			reg = <0x16000000 0x100>;
@@ -313,12 +352,12 @@
 			#size-cells = <1>;
 			ranges;
 
-			spi@16080000 {
+			gsbi1_spi: spi@16080000 {
 				compatible = "qcom,spi-qup-v1.1.1";
 				#address-cells = <1>;
 				#size-cells = <0>;
 				reg = <0x16080000 0x1000>;
-				interrupts = <0 147 0>;
+				interrupts = <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>;
 				spi-max-frequency = <24000000>;
 				cs-gpios = <&msmgpio 8 0>;
 
diff --git a/arch/arm/boot/dts/qcom-msm8974-fairphone-fp2.dts b/arch/arm/boot/dts/qcom-msm8974-fairphone-fp2.dts
deleted file mode 100644
index ea15b645b229..000000000000
--- a/arch/arm/boot/dts/qcom-msm8974-fairphone-fp2.dts
+++ /dev/null
@@ -1,410 +0,0 @@
-#include "qcom-msm8974.dtsi"
-#include "qcom-pm8841.dtsi"
-#include "qcom-pm8941.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
-
-
-/ {
-	model = "Fairphone 2";
-	compatible = "fairphone,fp2", "qcom,msm8974";
-
-	aliases {
-		serial0 = &blsp1_uart2;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	gpio-keys {
-		compatible = "gpio-keys";
-		input-name = "gpio-keys";
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&gpio_keys_pin_a>;
-
-		camera-snapshot {
-			label = "camera_snapshot";
-			gpios = <&pm8941_gpios 1 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_CAMERA>;
-			wakeup-source;
-			debounce-interval = <15>;
-		};
-
-		volume-down {
-			label = "volume_down";
-			gpios = <&pm8941_gpios 2 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_VOLUMEDOWN>;
-			wakeup-source;
-			debounce-interval = <15>;
-		};
-
-		volume-up {
-			label = "volume_up";
-			gpios = <&pm8941_gpios 5 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_VOLUMEUP>;
-			wakeup-source;
-			debounce-interval = <15>;
-		};
-	};
-
-	vibrator {
-		compatible = "gpio-vibrator";
-		enable-gpios = <&msmgpio 86 GPIO_ACTIVE_HIGH>;
-		vcc-supply = <&pm8941_l18>;
-	};
-
-	smd {
-		rpm {
-			rpm_requests {
-				pm8841-regulators {
-					s1 {
-						regulator-min-microvolt = <675000>;
-						regulator-max-microvolt = <1050000>;
-					};
-
-					s2 {
-						regulator-min-microvolt = <500000>;
-						regulator-max-microvolt = <1050000>;
-					};
-
-					s3 {
-						regulator-min-microvolt = <1050000>;
-						regulator-max-microvolt = <1050000>;
-					};
-				};
-
-				pm8941-regulators {
-					vdd_l1_l3-supply = <&pm8941_s1>;
-					vdd_l2_lvs1_2_3-supply = <&pm8941_s3>;
-					vdd_l4_l11-supply = <&pm8941_s1>;
-					vdd_l5_l7-supply = <&pm8941_s2>;
-					vdd_l6_l12_l14_l15-supply = <&pm8941_s2>;
-					vdd_l9_l10_l17_l22-supply = <&vreg_boost>;
-					vdd_l13_l20_l23_l24-supply = <&vreg_boost>;
-					vdd_l21-supply = <&vreg_boost>;
-
-					s1 {
-						regulator-min-microvolt = <1300000>;
-						regulator-max-microvolt = <1300000>;
-
-						regulator-always-on;
-						regulator-boot-on;
-					};
-
-					s2 {
-						regulator-min-microvolt = <2150000>;
-						regulator-max-microvolt = <2150000>;
-
-						regulator-boot-on;
-					};
-
-					s3 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-
-						regulator-always-on;
-						regulator-boot-on;
-					};
-
-					l1 {
-						regulator-min-microvolt = <1225000>;
-						regulator-max-microvolt = <1225000>;
-
-						regulator-always-on;
-						regulator-boot-on;
-					};
-
-					l2 {
-						regulator-min-microvolt = <1200000>;
-						regulator-max-microvolt = <1200000>;
-					};
-
-					l3 {
-						regulator-min-microvolt = <1225000>;
-						regulator-max-microvolt = <1225000>;
-					};
-
-					l4 {
-						regulator-min-microvolt = <1225000>;
-						regulator-max-microvolt = <1225000>;
-					};
-
-					l5 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-					};
-
-					l6 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-
-						regulator-boot-on;
-					};
-
-					l7 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-
-						regulator-boot-on;
-					};
-
-					l8 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-					};
-
-					l9 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <2950000>;
-					};
-
-					l10 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <2950000>;
-					};
-
-					l11 {
-						regulator-min-microvolt = <1225000>;
-						regulator-max-microvolt = <1350000>;
-					};
-
-					l12 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-
-						regulator-always-on;
-						regulator-boot-on;
-					};
-
-					l13 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <2950000>;
-
-						regulator-boot-on;
-					};
-
-					l14 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-					};
-
-					l15 {
-						regulator-min-microvolt = <2050000>;
-						regulator-max-microvolt = <2050000>;
-					};
-
-					l16 {
-						regulator-min-microvolt = <2700000>;
-						regulator-max-microvolt = <2700000>;
-					};
-
-					l17 {
-						regulator-min-microvolt = <2850000>;
-						regulator-max-microvolt = <2850000>;
-					};
-
-					l18 {
-						regulator-min-microvolt = <2850000>;
-						regulator-max-microvolt = <2850000>;
-					};
-
-					l19 {
-						regulator-min-microvolt = <2900000>;
-						regulator-max-microvolt = <3350000>;
-					};
-
-					l20 {
-						regulator-min-microvolt = <2950000>;
-						regulator-max-microvolt = <2950000>;
-
-						regulator-boot-on;
-						regulator-system-load = <200000>;
-						regulator-allow-set-load;
-					};
-
-					l21 {
-						regulator-min-microvolt = <2950000>;
-						regulator-max-microvolt = <2950000>;
-
-						regulator-boot-on;
-					};
-
-					l22 {
-						regulator-min-microvolt = <3000000>;
-						regulator-max-microvolt = <3300000>;
-					};
-
-					l23 {
-						regulator-min-microvolt = <3000000>;
-						regulator-max-microvolt = <3000000>;
-					};
-
-					l24 {
-						regulator-min-microvolt = <3075000>;
-						regulator-max-microvolt = <3075000>;
-
-						regulator-boot-on;
-					};
-				};
-			};
-		};
-	};
-};
-
-&soc {
-	serial@f991e000 {
-		status = "okay";
-	};
-
-	remoteproc@fb21b000 {
-		status = "okay";
-
-		vddmx-supply = <&pm8841_s1>;
-		vddcx-supply = <&pm8841_s2>;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&wcnss_pin_a>;
-
-		smd-edge {
-			qcom,remote-pid = <4>;
-			label = "pronto";
-
-			wcnss {
-				status = "okay";
-			};
-		};
-	};
-
-	pinctrl@fd510000 {
-		sdhc1_pin_a: sdhc1-pin-active {
-			clk {
-				pins = "sdc1_clk";
-				drive-strength = <16>;
-				bias-disable;
-			};
-
-			cmd-data {
-				pins = "sdc1_cmd", "sdc1_data";
-				drive-strength = <10>;
-				bias-pull-up;
-			};
-		};
-
-		sdhc2_pin_a: sdhc2-pin-active {
-			clk {
-				pins = "sdc2_clk";
-				drive-strength = <10>;
-				bias-disable;
-			};
-
-			cmd-data {
-				pins = "sdc2_cmd", "sdc2_data";
-				drive-strength = <6>;
-				bias-pull-up;
-			};
-		};
-
-		wcnss_pin_a: wcnss-pin-active {
-			wlan {
-				pins =  "gpio36", "gpio37", "gpio38", "gpio39", "gpio40";
-				function = "wlan";
-
-				drive-strength = <6>;
-				bias-pull-down;
-			};
-
-			bt {
-				pins = "gpio35", "gpio43", "gpio44";
-				function = "bt";
-
-				drive-strength = <2>;
-				bias-pull-down;
-			};
-
-			fm {
-				pins = "gpio41", "gpio42";
-				function = "fm";
-
-				drive-strength = <2>;
-				bias-pull-down;
-			};
-		};
-	};
-
-	sdhci@f9824900 {
-		status = "okay";
-
-		vmmc-supply = <&pm8941_l20>;
-		vqmmc-supply = <&pm8941_s3>;
-
-		bus-width = <8>;
-		non-removable;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&sdhc1_pin_a>;
-	};
-
-	sdhci@f98a4900 {
-		status = "okay";
-
-		vmmc-supply = <&pm8941_l21>;
-		vqmmc-supply = <&pm8941_l13>;
-
-		bus-width = <4>;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&sdhc2_pin_a>;
-	};
-
-	usb@f9a55000 {
-		status = "okay";
-
-		phys = <&usb_hs1_phy>;
-		phy-select = <&tcsr 0xb000 0>;
-		extcon = <&smbb>, <&usb_id>;
-		vbus-supply = <&chg_otg>;
-
-		hnp-disable;
-		srp-disable;
-		adp-disable;
-
-		ulpi {
-			phy@a {
-				status = "okay";
-
-				v1p8-supply = <&pm8941_l6>;
-				v3p3-supply = <&pm8941_l24>;
-
-				extcon = <&smbb>;
-				qcom,init-seq = /bits/ 8 <0x1 0x64>;
-			};
-		};
-	};
-
-	imem@fe805000 {
-		status = "okay";
-
-		reboot-mode {
-			mode-normal	= <0x77665501>;
-			mode-bootloader	= <0x77665500>;
-			mode-recovery	= <0x77665502>;
-		};
-	};
-};
-
-&spmi_bus {
-	pm8941@0 {
-		gpios@c000 {
-			gpio_keys_pin_a: gpio-keys-active {
-				pins = "gpio1", "gpio2", "gpio5";
-				function = "normal";
-
-				bias-pull-up;
-				power-source = <PM8941_GPIO_S3>;
-			};
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/qcom-msm8974-lge-nexus5-hammerhead.dts b/arch/arm/boot/dts/qcom-msm8974-lge-nexus5-hammerhead.dts
index 30ee913faae6..6daceaa87802 100644
--- a/arch/arm/boot/dts/qcom-msm8974-lge-nexus5-hammerhead.dts
+++ b/arch/arm/boot/dts/qcom-msm8974-lge-nexus5-hammerhead.dts
@@ -2,8 +2,8 @@
 #include "qcom-msm8974.dtsi"
 #include "qcom-pm8841.dtsi"
 #include "qcom-pm8941.dtsi"
-#include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
 
 / {
@@ -12,213 +12,31 @@
 
 	aliases {
 		serial0 = &blsp1_uart1;
-		serial1 = &blsp2_uart10;
+		serial1 = &blsp2_uart4;
 	};
 
 	chosen {
 		stdout-path = "serial0:115200n8";
 	};
 
-	smd {
-		rpm {
-			rpm_requests {
-				pm8841-regulators {
-					s1 {
-						regulator-min-microvolt = <675000>;
-						regulator-max-microvolt = <1050000>;
-					};
-
-					s2 {
-						regulator-min-microvolt = <500000>;
-						regulator-max-microvolt = <1050000>;
-					};
-
-					s3 {
-						regulator-min-microvolt = <1050000>;
-						regulator-max-microvolt = <1050000>;
-					};
-
-					s4 {
-						regulator-min-microvolt = <815000>;
-						regulator-max-microvolt = <900000>;
-					};
-				};
-
-				pm8941-regulators {
-					vdd_l1_l3-supply = <&pm8941_s1>;
-					vdd_l2_lvs1_2_3-supply = <&pm8941_s3>;
-					vdd_l4_l11-supply = <&pm8941_s1>;
-					vdd_l5_l7-supply = <&pm8941_s2>;
-					vdd_l6_l12_l14_l15-supply = <&pm8941_s2>;
-					vdd_l8_l16_l18_l19-supply = <&vreg_vph_pwr>;
-					vdd_l9_l10_l17_l22-supply = <&vreg_boost>;
-					vdd_l13_l20_l23_l24-supply = <&vreg_boost>;
-					vdd_l21-supply = <&vreg_boost>;
-
-					s1 {
-						regulator-min-microvolt = <1300000>;
-						regulator-max-microvolt = <1300000>;
-
-						regulator-always-on;
-						regulator-boot-on;
-					};
-
-					s2 {
-						regulator-min-microvolt = <2150000>;
-						regulator-max-microvolt = <2150000>;
-
-						regulator-boot-on;
-					};
-
-					s3 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-
-						regulator-always-on;
-						regulator-boot-on;
-					};
-
-					l1 {
-						regulator-min-microvolt = <1225000>;
-						regulator-max-microvolt = <1225000>;
-
-						regulator-always-on;
-						regulator-boot-on;
-					};
-
-					l2 {
-						regulator-min-microvolt = <1200000>;
-						regulator-max-microvolt = <1200000>;
-					};
-
-					l3 {
-						regulator-min-microvolt = <1225000>;
-						regulator-max-microvolt = <1225000>;
-					};
-
-					l4 {
-						regulator-min-microvolt = <1225000>;
-						regulator-max-microvolt = <1225000>;
-					};
-
-					l5 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-					};
-
-					l6 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-
-						regulator-boot-on;
-					};
-
-					l7 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-
-						regulator-boot-on;
-					};
-
-					l8 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-					};
-
-					l9 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <2950000>;
-					};
-
-					l10 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <2950000>;
-					};
-
-					l11 {
-						regulator-min-microvolt = <1300000>;
-						regulator-max-microvolt = <1300000>;
-					};
-
-					l12 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-
-						regulator-always-on;
-						regulator-boot-on;
-					};
-
-					l13 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <2950000>;
-
-						regulator-boot-on;
-					};
-
-					l14 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-					};
-
-					l15 {
-						regulator-min-microvolt = <2050000>;
-						regulator-max-microvolt = <2050000>;
-					};
-
-					l16 {
-						regulator-min-microvolt = <2700000>;
-						regulator-max-microvolt = <2700000>;
-					};
-
-					l17 {
-						regulator-min-microvolt = <2850000>;
-						regulator-max-microvolt = <2850000>;
-					};
-
-					l18 {
-						regulator-min-microvolt = <2850000>;
-						regulator-max-microvolt = <2850000>;
-					};
-
-					l19 {
-						regulator-min-microvolt = <3000000>;
-						regulator-max-microvolt = <3300000>;
-					};
-
-					l20 {
-						regulator-min-microvolt = <2950000>;
-						regulator-max-microvolt = <2950000>;
-
-						regulator-boot-on;
-						regulator-system-load = <200000>;
-						regulator-allow-set-load;
-					};
-
-					l21 {
-						regulator-min-microvolt = <2950000>;
-						regulator-max-microvolt = <2950000>;
-
-						regulator-boot-on;
-					};
-
-					l22 {
-						regulator-min-microvolt = <3000000>;
-						regulator-max-microvolt = <3300000>;
-					};
-
-					l23 {
-						regulator-min-microvolt = <3000000>;
-						regulator-max-microvolt = <3000000>;
-					};
-
-					l24 {
-						regulator-min-microvolt = <3075000>;
-						regulator-max-microvolt = <3075000>;
-
-						regulator-boot-on;
-					};
-				};
-			};
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_keys_pin_a>;
+
+		key-volume-up {
+			label = "volume_up";
+			gpios = <&pm8941_gpios 2 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			linux,code = <KEY_VOLUMEUP>;
+		};
+
+		key-volume-down {
+			label = "volume_down";
+			gpios = <&pm8941_gpios 3 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			linux,code = <KEY_VOLUMEDOWN>;
 		};
 	};
 
@@ -229,7 +47,7 @@
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
 
-		gpio = <&msmgpio 26 GPIO_ACTIVE_HIGH>;
+		gpio = <&tlmm 26 GPIO_ACTIVE_HIGH>;
 		enable-active-high;
 
 		pinctrl-names = "default";
@@ -237,526 +55,599 @@
 	};
 };
 
-&soc {
-	serial@f991d000 {
-		status = "okay";
+&blsp1_i2c1 {
+	status = "okay";
+	clock-frequency = <100000>;
+
+	charger: bq24192@6b {
+		compatible = "ti,bq24192";
+		reg = <0x6b>;
+		interrupts-extended = <&spmi_bus 0 0xd5 0 IRQ_TYPE_EDGE_FALLING>;
+
+		omit-battery-class;
+
+		usb_otg_vbus: usb-otg-vbus { };
 	};
 
-	pinctrl@fd510000 {
-		sdhc1_pin_a: sdhc1-pin-active {
-			clk {
-				pins = "sdc1_clk";
-				drive-strength = <16>;
-				bias-disable;
-			};
+	fuelgauge: max17048@36 {
+		compatible = "maxim,max17048";
+		reg = <0x36>;
 
-			cmd-data {
-				pins = "sdc1_cmd", "sdc1_data";
-				drive-strength = <10>;
-				bias-pull-up;
-			};
-		};
+		maxim,double-soc;
+		maxim,rcomp = /bits/ 8 <0x4d>;
 
-		sdhc2_pin_a: sdhc2-pin-active {
-			clk {
-				pins = "sdc2_clk";
-				drive-strength = <6>;
-				bias-disable;
-			};
+		interrupt-parent = <&tlmm>;
+		interrupts = <9 IRQ_TYPE_LEVEL_LOW>;
 
-			cmd-data {
-				pins = "sdc2_cmd", "sdc2_data";
-				drive-strength = <6>;
-				bias-pull-up;
-			};
-		};
+		pinctrl-names = "default";
+		pinctrl-0 = <&fuelgauge_pin>;
 
-		i2c1_pins: i2c1 {
-			mux {
-				pins = "gpio2", "gpio3";
-				function = "blsp_i2c1";
+		maxim,alert-low-soc-level = <2>;
+	};
+};
 
-				drive-strength = <2>;
-				bias-disable;
-			};
-		};
+&blsp1_i2c2 {
+	status = "okay";
+	clock-frequency = <355000>;
 
-		i2c2_pins: i2c2 {
-			mux {
-				pins = "gpio6", "gpio7";
-				function = "blsp_i2c2";
+	synaptics@70 {
+		compatible = "syna,rmi4-i2c";
+		reg = <0x70>;
 
-				drive-strength = <2>;
-				bias-disable;
-			};
-		};
+		interrupts-extended = <&tlmm 5 IRQ_TYPE_EDGE_FALLING>;
+		vdd-supply = <&pm8941_l22>;
+		vio-supply = <&pm8941_lvs3>;
 
-		i2c3_pins: i2c3 {
-			mux {
-				pins = "gpio10", "gpio11";
-				function = "blsp_i2c3";
-				drive-strength = <2>;
-				bias-disable;
-			};
-		};
+		pinctrl-names = "default";
+		pinctrl-0 = <&touch_pin>;
 
-		i2c11_pins: i2c11 {
-			mux {
-				pins = "gpio83", "gpio84";
-				function = "blsp_i2c11";
+		#address-cells = <1>;
+		#size-cells = <0>;
 
-				drive-strength = <2>;
-				bias-disable;
-			};
+		rmi4-f01@1 {
+			reg = <0x1>;
+			syna,nosleep-mode = <1>;
 		};
 
-		i2c12_pins: i2c12 {
-			mux {
-				pins = "gpio87", "gpio88";
-				function = "blsp_i2c12";
-				drive-strength = <2>;
-				bias-disable;
-			};
+		rmi4-f12@12 {
+			reg = <0x12>;
+			syna,sensor-type = <1>;
 		};
+	};
+};
 
-		mpu6515_pin: mpu6515 {
-			irq {
-				pins = "gpio73";
-				function = "gpio";
-				bias-disable;
-				input-enable;
-			};
-		};
+&blsp1_i2c3 {
+	status = "okay";
+	clock-frequency = <100000>;
+
+	avago_apds993@39 {
+		compatible = "avago,apds9930";
+		reg = <0x39>;
+		interrupts-extended = <&tlmm 61 IRQ_TYPE_EDGE_FALLING>;
+		vdd-supply = <&pm8941_l17>;
+		vddio-supply = <&pm8941_lvs1>;
+		led-max-microamp = <100000>;
+		amstaos,proximity-diodes = <0>;
+	};
+};
 
-		touch_pin: touch {
-			int {
-				pins = "gpio5";
-				function = "gpio";
+&blsp2_i2c5 {
+	status = "okay";
+	clock-frequency = <355000>;
 
-				drive-strength = <2>;
-				bias-disable;
-				input-enable;
-			};
+	led-controller@38 {
+		compatible = "ti,lm3630a";
+		status = "okay";
+		reg = <0x38>;
 
-			reset {
-				pins = "gpio8";
-				function = "gpio";
+		#address-cells = <1>;
+		#size-cells = <0>;
 
-				drive-strength = <2>;
-				bias-pull-up;
-			};
+		led@0 {
+			reg = <0>;
+			led-sources = <0 1>;
+			label = "lcd-backlight";
+			default-brightness = <200>;
 		};
+	};
+};
 
-		panel_pin: panel {
-			te {
-				pins = "gpio12";
-				function = "mdp_vsync";
+&blsp2_i2c6 {
+	status = "okay";
+	clock-frequency = <100000>;
 
-				drive-strength = <2>;
-				bias-disable;
-			};
-		};
+	mpu6515@68 {
+		compatible = "invensense,mpu6515";
+		reg = <0x68>;
+		interrupts-extended = <&tlmm 73 IRQ_TYPE_EDGE_FALLING>;
+		vddio-supply = <&pm8941_lvs1>;
 
-		bt_pin: bt {
-			hostwake {
-				pins = "gpio42";
-				function = "gpio";
-			};
+		pinctrl-names = "default";
+		pinctrl-0 = <&mpu6515_pin>;
 
-			devwake {
-				pins = "gpio62";
-				function = "gpio";
+		mount-matrix = "0", "-1", "0",
+				"-1", "0", "0",
+				"0", "0", "1";
+
+		i2c-gate {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			ak8963@f {
+				compatible = "asahi-kasei,ak8963";
+				reg = <0x0f>;
+				gpios = <&tlmm 67 GPIO_ACTIVE_HIGH>;
+				vid-supply = <&pm8941_lvs1>;
+				vdd-supply = <&pm8941_l17>;
 			};
 
-			shutdown {
-				pins = "gpio41";
-				function = "gpio";
+			bmp280@76 {
+				compatible = "bosch,bmp280";
+				reg = <0x76>;
+				vdda-supply = <&pm8941_lvs1>;
+				vddd-supply = <&pm8941_l17>;
 			};
 		};
+	};
+};
 
-		blsp2_uart10_pin_a: blsp2-uart10-pin-active {
-			tx {
-				pins = "gpio53";
-				function = "blsp_uart10";
+&blsp1_uart1 {
+	status = "okay";
+};
 
-				drive-strength = <2>;
-				bias-disable;
-			};
+&blsp2_uart4 {
+	status = "okay";
 
-			rx {
-				pins = "gpio54";
-				function = "blsp_uart10";
+	bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		max-speed = <3000000>;
 
-				drive-strength = <2>;
-				bias-pull-up;
-			};
+		pinctrl-names = "default";
+		pinctrl-0 = <&bt_pin>;
 
-			cts {
-				pins = "gpio55";
-				function = "blsp_uart10";
+		host-wakeup-gpios = <&tlmm 42 GPIO_ACTIVE_HIGH>;
+		device-wakeup-gpios = <&tlmm 62 GPIO_ACTIVE_HIGH>;
+		shutdown-gpios = <&tlmm 41 GPIO_ACTIVE_HIGH>;
+	};
+};
 
-				drive-strength = <2>;
-				bias-pull-up;
-			};
+&dsi0 {
+	status = "okay";
 
-			rts {
-				pins = "gpio56";
-				function = "blsp_uart10";
+	vdda-supply = <&pm8941_l2>;
+	vdd-supply = <&pm8941_lvs3>;
+	vddio-supply = <&pm8941_l12>;
 
-				drive-strength = <2>;
-				bias-disable;
+	panel: panel@0 {
+		reg = <0>;
+		compatible = "lg,acx467akm-7";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&panel_pin>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&dsi0_out>;
 			};
 		};
 	};
+};
 
-	sdhci@f9824900 {
-		status = "okay";
+&dsi0_out {
+	remote-endpoint = <&panel_in>;
+	data-lanes = <0 1 2 3>;
+};
 
-		vmmc-supply = <&pm8941_l20>;
-		vqmmc-supply = <&pm8941_s3>;
+&dsi0_phy {
+	status = "okay";
 
-		bus-width = <8>;
-		non-removable;
+	vddio-supply = <&pm8941_l12>;
+};
 
-		pinctrl-names = "default";
-		pinctrl-0 = <&sdhc1_pin_a>;
-	};
+&mdss {
+	status = "okay";
+};
 
-	sdhci@f98a4900 {
-		status = "okay";
+&otg {
+	status = "okay";
 
-		max-frequency = <100000000>;
-		bus-width = <4>;
-		non-removable;
-		vmmc-supply = <&vreg_wlan>;
-		vqmmc-supply = <&pm8941_s3>;
+	phys = <&usb_hs1_phy>;
+	phy-select = <&tcsr 0xb000 0>;
 
-		pinctrl-names = "default";
-		pinctrl-0 = <&sdhc2_pin_a>;
+	extcon = <&charger>, <&usb_id>;
+	vbus-supply = <&usb_otg_vbus>;
 
-		#address-cells = <1>;
-		#size-cells = <0>;
+	hnp-disable;
+	srp-disable;
+	adp-disable;
 
-		bcrmf@1 {
-			compatible = "brcm,bcm4339-fmac", "brcm,bcm4329-fmac";
-			reg = <1>;
+	ulpi {
+		phy@a {
+			status = "okay";
 
-			brcm,drive-strength = <10>;
+			v1p8-supply = <&pm8941_l6>;
+			v3p3-supply = <&pm8941_l24>;
 
-			pinctrl-names = "default";
-			pinctrl-0 = <&wlan_sleep_clk_pin>;
+			qcom,init-seq = /bits/ 8 <0x1 0x64>;
 		};
 	};
+};
 
-	gpio-keys {
-		compatible = "gpio-keys";
-		input-name = "gpio-keys";
+&pm8941_gpios {
+	gpio_keys_pin_a: gpio-keys-active-state {
+		pins = "gpio2", "gpio3";
+		function = "normal";
 
-		pinctrl-names = "default";
-		pinctrl-0 = <&gpio_keys_pin_a>;
+		bias-pull-up;
+		power-source = <PM8941_GPIO_S3>;
+	};
 
-		volume-up {
-			label = "volume_up";
-			gpios = <&pm8941_gpios 2 GPIO_ACTIVE_LOW>;
-			linux,input-type = <1>;
-			linux,code = <KEY_VOLUMEUP>;
-		};
+	fuelgauge_pin: fuelgauge-int-state {
+		pins = "gpio9";
+		function = "normal";
 
-		volume-down {
-			label = "volume_down";
-			gpios = <&pm8941_gpios 3 GPIO_ACTIVE_LOW>;
-			linux,input-type = <1>;
-			linux,code = <KEY_VOLUMEDOWN>;
-		};
+		bias-disable;
+		input-enable;
+		power-source = <PM8941_GPIO_S3>;
 	};
 
-	serial@f9960000 {
-		status = "okay";
+	wlan_sleep_clk_pin: wl-sleep-clk-state {
+		pins = "gpio16";
+		function = "func2";
 
-		pinctrl-names = "default";
-		pinctrl-0 = <&blsp2_uart10_pin_a>;
+		output-high;
+		power-source = <PM8941_GPIO_S3>;
+	};
 
-		bluetooth {
-			compatible = "brcm,bcm43438-bt";
-			max-speed = <3000000>;
+	wlan_regulator_pin: wl-reg-active-state {
+		pins = "gpio17";
+		function = "normal";
 
-			pinctrl-names = "default";
-			pinctrl-0 = <&bt_pin>;
+		bias-disable;
+		power-source = <PM8941_GPIO_S3>;
+	};
 
-			host-wakeup-gpios = <&msmgpio 42 GPIO_ACTIVE_HIGH>;
-			device-wakeup-gpios = <&msmgpio 62 GPIO_ACTIVE_HIGH>;
-			shutdown-gpios = <&msmgpio 41 GPIO_ACTIVE_HIGH>;
-		};
+	otg {
+		gpio-hog;
+		gpios = <35 GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "otg-gpio";
 	};
+};
 
-	i2c@f9967000 {
-		status = "okay";
-		pinctrl-names = "default";
-		pinctrl-0 = <&i2c11_pins>;
-		clock-frequency = <355000>;
-		qcom,src-freq = <50000000>;
+&pm8941_lpg {
+	status = "okay";
 
-		led-controller@38 {
-			compatible = "ti,lm3630a";
-			status = "okay";
-			reg = <0x38>;
+	qcom,power-source = <1>;
 
-			#address-cells = <1>;
-			#size-cells = <0>;
+	multi-led {
+		color = <LED_COLOR_ID_RGB>;
+		function = LED_FUNCTION_STATUS;
 
-			led@0 {
-				reg = <0>;
-				led-sources = <0 1>;
-				label = "lcd-backlight";
-				default-brightness = <200>;
-			};
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		led@7 {
+			reg = <7>;
+			color = <LED_COLOR_ID_RED>;
+		};
+
+		led@6 {
+			reg = <6>;
+			color = <LED_COLOR_ID_GREEN>;
+		};
+
+		led@5 {
+			reg = <5>;
+			color = <LED_COLOR_ID_BLUE>;
 		};
 	};
+};
 
-	i2c@f9968000 {
-		status = "okay";
-		pinctrl-names = "default";
-		pinctrl-0 = <&i2c12_pins>;
-		clock-frequency = <100000>;
-		qcom,src-freq = <50000000>;
-
-		mpu6515@68 {
-			compatible = "invensense,mpu6515";
-			reg = <0x68>;
-			interrupts-extended = <&msmgpio 73 IRQ_TYPE_EDGE_FALLING>;
-			vddio-supply = <&pm8941_lvs1>;
-
-			pinctrl-names = "default";
-			pinctrl-0 = <&mpu6515_pin>;
-
-			mount-matrix = "0", "-1", "0",
-				       "-1", "0", "0",
-				       "0", "0", "1";
-
-			i2c-gate {
-				#address-cells = <1>;
-				#size-cells = <0>;
-				ak8963@f {
-					compatible = "asahi-kasei,ak8963";
-					reg = <0x0f>;
-					gpios = <&msmgpio 67 0>;
-					vid-supply = <&pm8941_lvs1>;
-					vdd-supply = <&pm8941_l17>;
-				};
-
-				bmp280@76 {
-					compatible = "bosch,bmp280";
-					reg = <0x76>;
-					vdda-supply = <&pm8941_lvs1>;
-					vddd-supply = <&pm8941_l17>;
-				};
-			};
+&rpm_requests {
+	pm8841-regulators {
+		compatible = "qcom,rpm-pm8841-regulators";
+
+		pm8841_s1: s1 {
+			regulator-min-microvolt = <675000>;
+			regulator-max-microvolt = <1050000>;
+		};
+
+		pm8841_s2: s2 {
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1050000>;
+		};
+
+		pm8841_s3: s3 {
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1050000>;
+		};
+
+		pm8841_s4: s4 {
+			regulator-min-microvolt = <815000>;
+			regulator-max-microvolt = <900000>;
 		};
 	};
 
-	i2c@f9923000 {
-		status = "okay";
-		pinctrl-names = "default";
-		pinctrl-0 = <&i2c1_pins>;
-		clock-frequency = <100000>;
-		qcom,src-freq = <50000000>;
+	pm8941-regulators {
+		compatible = "qcom,rpm-pm8941-regulators";
+
+		vdd_l1_l3-supply = <&pm8941_s1>;
+		vdd_l2_lvs1_2_3-supply = <&pm8941_s3>;
+		vdd_l4_l11-supply = <&pm8941_s1>;
+		vdd_l5_l7-supply = <&pm8941_s2>;
+		vdd_l6_l12_l14_l15-supply = <&pm8941_s2>;
+		vdd_l8_l16_l18_l19-supply = <&vreg_vph_pwr>;
+		vdd_l9_l10_l17_l22-supply = <&vreg_boost>;
+		vdd_l13_l20_l23_l24-supply = <&vreg_boost>;
+		vdd_l21-supply = <&vreg_boost>;
+
+		pm8941_s1: s1 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
 
-		charger: bq24192@6b {
-			compatible = "ti,bq24192";
-			reg = <0x6b>;
-			interrupts-extended = <&spmi_bus 0 0xd5 0 IRQ_TYPE_EDGE_FALLING>;
+		pm8941_s2: s2 {
+			regulator-min-microvolt = <2150000>;
+			regulator-max-microvolt = <2150000>;
+			regulator-boot-on;
+		};
 
-			omit-battery-class;
+		pm8941_s3: s3 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
 
-			usb_otg_vbus: usb-otg-vbus { };
+		pm8941_l1: l1 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+			regulator-always-on;
+			regulator-boot-on;
 		};
 
-		fuelgauge: max17048@36 {
-			compatible = "maxim,max17048";
-			reg = <0x36>;
+		pm8941_l2: l2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
 
-			maxim,double-soc;
-			maxim,rcomp = /bits/ 8 <0x4d>;
+		pm8941_l3: l3 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+		};
 
-			interrupt-parent = <&msmgpio>;
-			interrupts = <9 IRQ_TYPE_LEVEL_LOW>;
+		pm8941_l4: l4 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+		};
 
-			pinctrl-names = "default";
-			pinctrl-0 = <&fuelgauge_pin>;
+		pm8941_l5: l5 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
 
-			maxim,alert-low-soc-level = <2>;
+		pm8941_l6: l6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-boot-on;
 		};
-	};
 
-	i2c@f9924000 {
-		status = "okay";
+		pm8941_l7: l7 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-boot-on;
+		};
 
-		clock-frequency = <355000>;
-		qcom,src-freq = <50000000>;
+		pm8941_l8: l8 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
 
-		pinctrl-names = "default";
-		pinctrl-0 = <&i2c2_pins>;
+		pm8941_l9: l9 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
 
-		synaptics@70 {
-			compatible = "syna,rmi4-i2c";
-			reg = <0x70>;
+		pm8941_l10: l10 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
 
-			interrupts-extended = <&msmgpio 5 IRQ_TYPE_EDGE_FALLING>;
-			vdd-supply = <&pm8941_l22>;
-			vio-supply = <&pm8941_lvs3>;
+		pm8941_l11: l11 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+		};
 
-			pinctrl-names = "default";
-			pinctrl-0 = <&touch_pin>;
+		pm8941_l12: l12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
 
-			#address-cells = <1>;
-			#size-cells = <0>;
+		pm8941_l13: l13 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-boot-on;
+		};
 
-			rmi4-f01@1 {
-				reg = <0x1>;
-				syna,nosleep-mode = <1>;
-			};
+		pm8941_l14: l14 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
 
-			rmi4-f12@12 {
-				reg = <0x12>;
-				syna,sensor-type = <1>;
-			};
+		pm8941_l15: l15 {
+			regulator-min-microvolt = <2050000>;
+			regulator-max-microvolt = <2050000>;
 		};
-	};
 
-	i2c@f9925000 {
-		status = "okay";
-		pinctrl-names = "default";
-		pinctrl-0 = <&i2c3_pins>;
-		clock-frequency = <100000>;
-		qcom,src-freq = <50000000>;
-
-		avago_apds993@39 {
-			compatible = "avago,apds9930";
-			reg = <0x39>;
-			interrupts-extended = <&msmgpio 61 IRQ_TYPE_EDGE_FALLING>;
-			vdd-supply = <&pm8941_l17>;
-			vddio-supply = <&pm8941_lvs1>;
-			led-max-microamp = <100000>;
-			amstaos,proximity-diodes = <0>;
+		pm8941_l16: l16 {
+			regulator-min-microvolt = <2700000>;
+			regulator-max-microvolt = <2700000>;
 		};
-	};
 
-	usb@f9a55000 {
-		status = "okay";
+		pm8941_l17: l17 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+		};
 
-		phys = <&usb_hs1_phy>;
-		phy-select = <&tcsr 0xb000 0>;
+		pm8941_l18: l18 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+		};
 
-		extcon = <&charger>, <&usb_id>;
-		vbus-supply = <&usb_otg_vbus>;
+		pm8941_l19: l19 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3300000>;
+		};
 
-		hnp-disable;
-		srp-disable;
-		adp-disable;
+		pm8941_l20: l20 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-system-load = <200000>;
+			regulator-allow-set-load;
+			regulator-boot-on;
+		};
 
-		ulpi {
-			phy@a {
-				status = "okay";
+		pm8941_l21: l21 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-boot-on;
+		};
 
-				v1p8-supply = <&pm8941_l6>;
-				v3p3-supply = <&pm8941_l24>;
+		pm8941_l22: l22 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3300000>;
+		};
 
-				qcom,init-seq = /bits/ 8 <0x1 0x64>;
-			};
+		pm8941_l23: l23 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+		};
+
+		pm8941_l24: l24 {
+			regulator-min-microvolt = <3075000>;
+			regulator-max-microvolt = <3075000>;
+			regulator-boot-on;
 		};
+
+		pm8941_lvs1: lvs1 {};
+		pm8941_lvs3: lvs3 {};
 	};
+};
 
-	mdss@fd900000 {
-		status = "okay";
+&sdhc_1 {
+	status = "okay";
 
-		mdp@fd900000 {
-			status = "okay";
-		};
+	vmmc-supply = <&pm8941_l20>;
+	vqmmc-supply = <&pm8941_s3>;
 
-		dsi@fd922800 {
-			status = "okay";
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sdc1_on>;
+	pinctrl-1 = <&sdc1_off>;
+};
 
-			vdda-supply = <&pm8941_l2>;
-			vdd-supply = <&pm8941_lvs3>;
-			vddio-supply = <&pm8941_l12>;
+&sdhc_2 {
+	status = "okay";
 
-			#address-cells = <1>;
-			#size-cells = <0>;
+	max-frequency = <100000000>;
+	vmmc-supply = <&vreg_wlan>;
+	vqmmc-supply = <&pm8941_s3>;
+	non-removable;
 
-			ports {
-				port@1 {
-					endpoint {
-						remote-endpoint = <&panel_in>;
-						data-lanes = <0 1 2 3>;
-					};
-				};
-			};
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sdc2_on>;
+	pinctrl-1 = <&sdc2_off>;
 
-			panel: panel@0 {
-				reg = <0>;
-				compatible = "lg,acx467akm-7";
+	bcrmf@1 {
+		compatible = "brcm,bcm4339-fmac", "brcm,bcm4329-fmac";
+		reg = <1>;
 
-				pinctrl-names = "default";
-				pinctrl-0 = <&panel_pin>;
+		brcm,drive-strength = <10>;
 
-				port {
-					panel_in: endpoint {
-						remote-endpoint = <&dsi0_out>;
-					};
-				};
-			};
+		pinctrl-names = "default";
+		pinctrl-0 = <&wlan_sleep_clk_pin>;
+	};
+};
+
+&tlmm {
+	sdc1_on: sdc1-on {
+		clk {
+			pins = "sdc1_clk";
+			drive-strength = <16>;
+			bias-disable;
 		};
 
-		dsi-phy@fd922a00 {
-			status = "okay";
+		cmd-data {
+			pins = "sdc1_cmd", "sdc1_data";
+			drive-strength = <10>;
+			bias-pull-up;
+		};
+	};
 
-			vddio-supply = <&pm8941_l12>;
+	sdc2_on: sdc2-on {
+		clk {
+			pins = "sdc2_clk";
+			drive-strength = <6>;
+			bias-disable;
+		};
+
+		cmd-data {
+			pins = "sdc2_cmd", "sdc2_data";
+			drive-strength = <6>;
+			bias-pull-up;
 		};
 	};
-};
 
-&spmi_bus {
-	pm8941@0 {
-		gpios@c000 {
-			gpio_keys_pin_a: gpio-keys-active {
-				pins = "gpio2", "gpio3";
-				function = "normal";
+	mpu6515_pin: mpu6515 {
+		pins = "gpio73";
+		function = "gpio";
+		bias-disable;
+		input-enable;
+	};
 
-				bias-pull-up;
-				power-source = <PM8941_GPIO_S3>;
-			};
+	touch_pin: touch {
+		int {
+			pins = "gpio5";
+			function = "gpio";
 
-			fuelgauge_pin: fuelgauge-int {
-				pins = "gpio9";
-				function = "normal";
+			drive-strength = <2>;
+			bias-disable;
+			input-enable;
+		};
 
-				bias-disable;
-				input-enable;
-				power-source = <PM8941_GPIO_S3>;
-			};
+		reset {
+			pins = "gpio8";
+			function = "gpio";
 
-			wlan_sleep_clk_pin: wl-sleep-clk {
-				pins = "gpio16";
-				function = "func2";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
 
-				output-high;
-				power-source = <PM8941_GPIO_S3>;
-			};
+	panel_pin: panel {
+		pins = "gpio12";
+		function = "mdp_vsync";
+		drive-strength = <2>;
+		bias-disable;
+	};
 
-			wlan_regulator_pin: wl-reg-active {
-				pins = "gpio17";
-				function = "normal";
+	bt_pin: bt {
+		hostwake {
+			pins = "gpio42";
+			function = "gpio";
+		};
 
-				bias-disable;
-				power-source = <PM8941_GPIO_S3>;
-			};
+		devwake {
+			pins = "gpio62";
+			function = "gpio";
+		};
 
-			otg {
-				gpio-hog;
-				gpios = <35 GPIO_ACTIVE_HIGH>;
-				output-high;
-				line-name = "otg-gpio";
-			};
+		shutdown {
+			pins = "gpio41";
+			function = "gpio";
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/qcom-msm8974-samsung-klte.dts b/arch/arm/boot/dts/qcom-msm8974-samsung-klte.dts
deleted file mode 100644
index 003f0fa9c857..000000000000
--- a/arch/arm/boot/dts/qcom-msm8974-samsung-klte.dts
+++ /dev/null
@@ -1,909 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-#include "qcom-msm8974pro.dtsi"
-#include "qcom-pma8084.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
-#include <dt-bindings/leds/common.h>
-
-/ {
-	model = "Samsung Galaxy S5";
-	compatible = "samsung,klte", "qcom,msm8974";
-
-	aliases {
-		serial0 = &blsp1_uart1;
-		mmc0 = &sdhc_1; /* SDC1 eMMC slot */
-		mmc1 = &sdhc_2; /* SDC2 SD card slot */
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	smd {
-		rpm {
-			rpm_requests {
-				pma8084-regulators {
-					compatible = "qcom,rpm-pma8084-regulators";
-					status = "okay";
-
-					pma8084_s1: s1 {
-						regulator-min-microvolt = <675000>;
-						regulator-max-microvolt = <1050000>;
-						regulator-always-on;
-					};
-
-					pma8084_s2: s2 {
-						regulator-min-microvolt = <500000>;
-						regulator-max-microvolt = <1050000>;
-					};
-
-					pma8084_s3: s3 {
-						regulator-min-microvolt = <1300000>;
-						regulator-max-microvolt = <1300000>;
-					};
-
-					pma8084_s4: s4 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-					};
-
-					pma8084_s5: s5 {
-						regulator-min-microvolt = <2150000>;
-						regulator-max-microvolt = <2150000>;
-					};
-
-					pma8084_s6: s6 {
-						regulator-min-microvolt = <1050000>;
-						regulator-max-microvolt = <1050000>;
-					};
-
-					pma8084_l1: l1 {
-						regulator-min-microvolt = <1225000>;
-						regulator-max-microvolt = <1225000>;
-					};
-
-					pma8084_l2: l2 {
-						regulator-min-microvolt = <1200000>;
-						regulator-max-microvolt = <1200000>;
-					};
-
-					pma8084_l3: l3 {
-						regulator-min-microvolt = <1050000>;
-						regulator-max-microvolt = <1200000>;
-					};
-
-					pma8084_l4: l4 {
-						regulator-min-microvolt = <1200000>;
-						regulator-max-microvolt = <1225000>;
-					};
-
-					pma8084_l5: l5 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-					};
-
-					pma8084_l6: l6 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-					};
-
-					pma8084_l7: l7 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-					};
-
-					pma8084_l8: l8 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-					};
-
-					pma8084_l9: l9 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <2950000>;
-					};
-
-					pma8084_l10: l10 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <2950000>;
-					};
-
-					pma8084_l11: l11 {
-						regulator-min-microvolt = <1300000>;
-						regulator-max-microvolt = <1300000>;
-					};
-
-					pma8084_l12: l12 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-						regulator-always-on;
-					};
-
-					pma8084_l13: l13 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <2950000>;
-					};
-
-					pma8084_l14: l14 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-					};
-
-					pma8084_l15: l15 {
-						regulator-min-microvolt = <2050000>;
-						regulator-max-microvolt = <2050000>;
-					};
-
-					pma8084_l16: l16 {
-						regulator-min-microvolt = <2700000>;
-						regulator-max-microvolt = <2700000>;
-					};
-
-					pma8084_l17: l17 {
-						regulator-min-microvolt = <2850000>;
-						regulator-max-microvolt = <2850000>;
-					};
-
-					pma8084_l18: l18 {
-						regulator-min-microvolt = <2850000>;
-						regulator-max-microvolt = <2850000>;
-					};
-
-					pma8084_l19: l19 {
-						regulator-min-microvolt = <3300000>;
-						regulator-max-microvolt = <3300000>;
-					};
-
-					pma8084_l20: l20 {
-						regulator-min-microvolt = <2950000>;
-						regulator-max-microvolt = <2950000>;
-
-						regulator-allow-set-load;
-						regulator-system-load = <200000>;
-					};
-
-					pma8084_l21: l21 {
-						regulator-min-microvolt = <2950000>;
-						regulator-max-microvolt = <2950000>;
-
-						regulator-allow-set-load;
-						regulator-system-load = <200000>;
-					};
-
-					pma8084_l22: l22 {
-						regulator-min-microvolt = <3000000>;
-						regulator-max-microvolt = <3300000>;
-					};
-
-					pma8084_l23: l23 {
-						regulator-min-microvolt = <3000000>;
-						regulator-max-microvolt = <3000000>;
-					};
-
-					pma8084_l24: l24 {
-						regulator-min-microvolt = <3075000>;
-						regulator-max-microvolt = <3075000>;
-					};
-
-					pma8084_l25: l25 {
-						regulator-min-microvolt = <2100000>;
-						regulator-max-microvolt = <2100000>;
-					};
-
-					pma8084_l26: l26 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <2050000>;
-					};
-
-					pma8084_l27: l27 {
-						regulator-min-microvolt = <1000000>;
-						regulator-max-microvolt = <1225000>;
-					};
-
-					pma8084_lvs1: lvs1 {};
-					pma8084_lvs2: lvs2 {};
-					pma8084_lvs3: lvs3 {};
-					pma8084_lvs4: lvs4 {};
-
-					pma8084_5vs1: 5vs1 {};
-				};
-			};
-		};
-	};
-
-	i2c-gpio-touchkey {
-		compatible = "i2c-gpio";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		sda-gpios = <&msmgpio 95 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
-		scl-gpios = <&msmgpio 96 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&i2c_touchkey_pins>;
-
-		touchkey@20 {
-			compatible = "cypress,tm2-touchkey";
-			reg = <0x20>;
-
-			interrupt-parent = <&pma8084_gpios>;
-			interrupts = <6 IRQ_TYPE_EDGE_FALLING>;
-			pinctrl-names = "default";
-			pinctrl-0 = <&touchkey_pin>;
-
-			vcc-supply = <&max77826_ldo15>;
-			vdd-supply = <&pma8084_l19>;
-
-			linux,keycodes = <KEY_APPSELECT KEY_BACK>;
-		};
-	};
-
-	i2c-gpio-led {
-		compatible = "i2c-gpio";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		scl-gpios = <&msmgpio 121 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
-		sda-gpios = <&msmgpio 120 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&i2c_led_gpioex_pins>;
-
-		i2c-gpio,delay-us = <2>;
-
-		gpio_expander: gpio@20 {
-			compatible = "nxp,pcal6416";
-			reg = <0x20>;
-
-			gpio-controller;
-			#gpio-cells = <2>;
-
-			vcc-supply = <&pma8084_s4>;
-
-			pinctrl-names = "default";
-			pinctrl-0 = <&gpioex_pin>;
-
-			reset-gpios = <&msmgpio 145 GPIO_ACTIVE_LOW>;
-		};
-
-		led-controller@30 {
-			compatible = "panasonic,an30259a";
-			reg = <0x30>;
-
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			led@1 {
-				reg = <1>;
-				function = LED_FUNCTION_STATUS;
-				color = <LED_COLOR_ID_RED>;
-			};
-
-			led@2 {
-				reg = <2>;
-				function = LED_FUNCTION_STATUS;
-				color = <LED_COLOR_ID_GREEN>;
-			};
-
-			led@3 {
-				reg = <3>;
-				function = LED_FUNCTION_STATUS;
-				color = <LED_COLOR_ID_BLUE>;
-			};
-		};
-	};
-
-	vreg_wlan: wlan-regulator {
-		compatible = "regulator-fixed";
-
-		regulator-name = "wl-reg";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-
-		gpio = <&gpio_expander 8 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-	};
-
-	vreg_panel: panel-regulator {
-		compatible = "regulator-fixed";
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&panel_en_pin>;
-
-		regulator-name = "panel-vddr-reg";
-		regulator-min-microvolt = <1500000>;
-		regulator-max-microvolt = <1500000>;
-
-		gpio = <&pma8084_gpios 14 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-	};
-
-	/delete-node/ vreg-boost;
-
-	adsp-pil {
-		cx-supply = <&pma8084_s2>;
-	};
-};
-
-&soc {
-	serial@f991e000 {
-		status = "okay";
-	};
-
-	/* blsp2_uart8 */
-	serial@f995e000 {
-		status = "okay";
-
-		pinctrl-names = "default", "sleep";
-		pinctrl-0 = <&blsp2_uart8_pins_active>;
-		pinctrl-1 = <&blsp2_uart8_pins_sleep>;
-
-		bluetooth {
-			compatible = "brcm,bcm43540-bt";
-			max-speed = <3000000>;
-			pinctrl-names = "default";
-			pinctrl-0 = <&bt_pins>;
-			device-wakeup-gpios = <&msmgpio 91 GPIO_ACTIVE_HIGH>;
-			shutdown-gpios = <&gpio_expander 9 GPIO_ACTIVE_HIGH>;
-			interrupt-parent = <&msmgpio>;
-			interrupts = <75 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "host-wakeup";
-		};
-	};
-
-	gpio-keys {
-		compatible = "gpio-keys";
-		input-name = "gpio-keys";
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&gpio_keys_pin_a>;
-
-		volume-down {
-			label = "volume_down";
-			gpios = <&pma8084_gpios 2 GPIO_ACTIVE_LOW>;
-			linux,input-type = <1>;
-			linux,code = <KEY_VOLUMEDOWN>;
-			debounce-interval = <15>;
-		};
-
-		home-key {
-			label = "home_key";
-			gpios = <&pma8084_gpios 3 GPIO_ACTIVE_LOW>;
-			linux,input-type = <1>;
-			linux,code = <KEY_HOMEPAGE>;
-			wakeup-source;
-			debounce-interval = <15>;
-		};
-
-		volume-up {
-			label = "volume_up";
-			gpios = <&pma8084_gpios 5 GPIO_ACTIVE_LOW>;
-			linux,input-type = <1>;
-			linux,code = <KEY_VOLUMEUP>;
-			debounce-interval = <15>;
-		};
-	};
-
-	pinctrl@fd510000 {
-		blsp2_uart8_pins_active: blsp2-uart8-pins-active {
-			pins = "gpio45", "gpio46", "gpio47", "gpio48";
-			function = "blsp_uart8";
-			drive-strength = <8>;
-			bias-disable;
-		};
-
-		blsp2_uart8_pins_sleep: blsp2-uart8-pins-sleep {
-			pins = "gpio45", "gpio46", "gpio47", "gpio48";
-			function = "gpio";
-			drive-strength = <2>;
-			bias-pull-down;
-		};
-
-		bt_pins: bt-pins {
-			hostwake {
-				pins = "gpio75";
-				function = "gpio";
-				drive-strength = <16>;
-				input-enable;
-			};
-
-			devwake {
-				pins = "gpio91";
-				function = "gpio";
-				drive-strength = <2>;
-			};
-		};
-
-		sdhc1_pin_a: sdhc1-pin-active {
-			clk {
-				pins = "sdc1_clk";
-				drive-strength = <4>;
-				bias-disable;
-			};
-
-			cmd-data {
-				pins = "sdc1_cmd", "sdc1_data";
-				drive-strength = <4>;
-				bias-pull-up;
-			};
-		};
-
-		sdhc2_pin_a: sdhc2-pin-active {
-			clk-cmd-data {
-				pins = "gpio35", "gpio36", "gpio37", "gpio38",
-					"gpio39", "gpio40";
-				function = "sdc3";
-				drive-strength = <8>;
-				bias-disable;
-			};
-		};
-
-		sdhc2_cd_pin: sdhc2-cd {
-			pins = "gpio62";
-			function = "gpio";
-
-			drive-strength = <2>;
-			bias-disable;
-		};
-
-		sdhc3_pin_a: sdhc3-pin-active {
-			clk {
-				pins = "sdc2_clk";
-				drive-strength = <6>;
-				bias-disable;
-			};
-
-			cmd-data {
-				pins = "sdc2_cmd", "sdc2_data";
-				drive-strength = <6>;
-				bias-pull-up;
-			};
-		};
-
-		i2c2_pins: i2c2 {
-			mux {
-				pins = "gpio6", "gpio7";
-				function = "blsp_i2c2";
-
-				drive-strength = <2>;
-				bias-disable;
-			};
-		};
-
-		i2c6_pins: i2c6 {
-			mux {
-				pins = "gpio29", "gpio30";
-				function = "blsp_i2c6";
-
-				drive-strength = <2>;
-				bias-disable;
-			};
-		};
-
-		i2c12_pins: i2c12 {
-			mux {
-				pins = "gpio87", "gpio88";
-				function = "blsp_i2c12";
-
-				drive-strength = <2>;
-				bias-disable;
-			};
-		};
-
-		i2c_touchkey_pins: i2c-touchkey {
-			mux {
-				pins = "gpio95", "gpio96";
-				function = "gpio";
-				input-enable;
-				bias-pull-up;
-			};
-		};
-
-		i2c_led_gpioex_pins: i2c-led-gpioex {
-			mux {
-				pins = "gpio120", "gpio121";
-				function = "gpio";
-				input-enable;
-				bias-pull-down;
-			};
-		};
-
-		gpioex_pin: gpioex {
-			res {
-				pins = "gpio145";
-				function = "gpio";
-
-				bias-pull-up;
-				drive-strength = <2>;
-			};
-		};
-
-		wifi_pin: wifi {
-			int {
-				pins = "gpio92";
-				function = "gpio";
-
-				input-enable;
-				bias-pull-down;
-			};
-		};
-
-		panel_te_pin: panel {
-			te {
-				pins = "gpio12";
-				function = "mdp_vsync";
-
-				drive-strength = <2>;
-				bias-disable;
-			};
-		};
-	};
-
-	sdhc_1: sdhci@f9824900 {
-		status = "okay";
-
-		vmmc-supply = <&pma8084_l20>;
-		vqmmc-supply = <&pma8084_s4>;
-
-		bus-width = <8>;
-		non-removable;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&sdhc1_pin_a>;
-	};
-
-	sdhc_2: sdhci@f9864900 {
-		status = "okay";
-
-		max-frequency = <100000000>;
-
-		vmmc-supply = <&pma8084_l21>;
-		vqmmc-supply = <&pma8084_l13>;
-
-		bus-width = <4>;
-
-		/* cd-gpio is intentionally disabled. If enabled, an SD card
-		 * present during boot is not initialized correctly. Without
-		 * cd-gpios the driver resorts to polling, so hotplug works.
-		 */
-		pinctrl-names = "default";
-		pinctrl-0 = <&sdhc2_pin_a /* &sdhc2_cd_pin */>;
-		// cd-gpios = <&msmgpio 62 GPIO_ACTIVE_LOW>;
-	};
-
-	sdhci@f98a4900 {
-		status = "okay";
-
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		max-frequency = <100000000>;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&sdhc3_pin_a>;
-
-		vmmc-supply = <&vreg_wlan>;
-		vqmmc-supply = <&pma8084_s4>;
-
-		bus-width = <4>;
-		non-removable;
-
-		wifi@1 {
-			reg = <1>;
-			compatible = "brcm,bcm4329-fmac";
-
-			interrupt-parent = <&msmgpio>;
-			interrupts = <92 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "host-wake";
-
-			pinctrl-names = "default";
-			pinctrl-0 = <&wlan_sleep_clk_pin &wifi_pin>;
-		};
-	};
-
-	usb@f9a55000 {
-		status = "okay";
-
-		phys = <&usb_hs1_phy>;
-		phy-select = <&tcsr 0xb000 0>;
-		/*extcon = <&smbb>, <&usb_id>;*/
-		/*vbus-supply = <&chg_otg>;*/
-
-		hnp-disable;
-		srp-disable;
-		adp-disable;
-
-		ulpi {
-			phy@a {
-				status = "okay";
-
-				v1p8-supply = <&pma8084_l6>;
-				v3p3-supply = <&pma8084_l24>;
-
-				/*extcon = <&smbb>;*/
-				qcom,init-seq = /bits/ 8 <0x1 0x64>;
-			};
-		};
-	};
-
-	i2c@f9924000 {
-		status = "okay";
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&i2c2_pins>;
-
-		touchscreen@20 {
-			compatible = "syna,rmi4-i2c";
-			reg = <0x20>;
-
-			interrupt-parent = <&pma8084_gpios>;
-			interrupts = <8 IRQ_TYPE_EDGE_FALLING>;
-
-			vdd-supply = <&max77826_ldo13>;
-			vio-supply = <&pma8084_lvs2>;
-
-			pinctrl-names = "default";
-			pinctrl-0 = <&touch_pin>;
-
-			syna,startup-delay-ms = <100>;
-
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			rmi4-f01@1 {
-				reg = <0x1>;
-				syna,nosleep-mode = <1>;
-			};
-
-			rmi4-f12@12 {
-				reg = <0x12>;
-				syna,sensor-type = <1>;
-			};
-		};
-	};
-
-	i2c@f9928000 {
-		status = "okay";
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&i2c6_pins>;
-
-		pmic@60 {
-			reg = <0x60>;
-			compatible = "maxim,max77826";
-
-			regulators {
-				max77826_ldo1: LDO1 {
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <1200000>;
-				};
-
-				max77826_ldo2: LDO2 {
-					regulator-min-microvolt = <1000000>;
-					regulator-max-microvolt = <1000000>;
-				};
-
-				max77826_ldo3: LDO3 {
-					regulator-min-microvolt = <1200000>;
-					regulator-max-microvolt = <1200000>;
-				};
-
-				max77826_ldo4: LDO4 {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-				};
-
-				max77826_ldo5: LDO5 {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-				};
-
-				max77826_ldo6: LDO6 {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <3300000>;
-				};
-
-				max77826_ldo7: LDO7 {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-				};
-
-				max77826_ldo8: LDO8 {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <3300000>;
-				};
-
-				max77826_ldo9: LDO9 {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-				};
-
-				max77826_ldo10: LDO10 {
-					regulator-min-microvolt = <2800000>;
-					regulator-max-microvolt = <2950000>;
-				};
-
-				max77826_ldo11: LDO11 {
-					regulator-min-microvolt = <2700000>;
-					regulator-max-microvolt = <2950000>;
-				};
-
-				max77826_ldo12: LDO12 {
-					regulator-min-microvolt = <2500000>;
-					regulator-max-microvolt = <3300000>;
-				};
-
-				max77826_ldo13: LDO13 {
-					regulator-min-microvolt = <3300000>;
-					regulator-max-microvolt = <3300000>;
-				};
-
-				max77826_ldo14: LDO14 {
-					regulator-min-microvolt = <3300000>;
-					regulator-max-microvolt = <3300000>;
-				};
-
-				max77826_ldo15: LDO15 {
-					regulator-min-microvolt = <1800000>;
-					regulator-max-microvolt = <1800000>;
-				};
-
-				max77826_buck: BUCK {
-					regulator-min-microvolt = <1225000>;
-					regulator-max-microvolt = <1225000>;
-				};
-
-				max77826_buckboost: BUCKBOOST {
-					regulator-min-microvolt = <3400000>;
-					regulator-max-microvolt = <3400000>;
-				};
-			};
-		};
-	};
-
-	i2c@f9968000 {
-		status = "okay";
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&i2c12_pins>;
-
-		fuelgauge@36 {
-			compatible = "maxim,max17048";
-			reg = <0x36>;
-
-			maxim,double-soc;
-			maxim,rcomp = /bits/ 8 <0x56>;
-
-			interrupt-parent = <&pma8084_gpios>;
-			interrupts = <21 IRQ_TYPE_LEVEL_LOW>;
-
-			pinctrl-names = "default";
-			pinctrl-0 = <&fuelgauge_pin>;
-		};
-	};
-
-	adreno@fdb00000 {
-		status = "ok";
-	};
-
-	mdss@fd900000 {
-		status = "ok";
-
-		mdp@fd900000 {
-			status = "ok";
-		};
-
-		dsi@fd922800 {
-			status = "ok";
-
-			vdda-supply = <&pma8084_l2>;
-			vdd-supply = <&pma8084_l22>;
-			vddio-supply = <&pma8084_l12>;
-
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			ports {
-				port@1 {
-					endpoint {
-						remote-endpoint = <&panel_in>;
-						data-lanes = <0 1 2 3>;
-					};
-				};
-			};
-
-			panel: panel@0 {
-				reg = <0>;
-				compatible = "samsung,s6e3fa2";
-
-				pinctrl-names = "default";
-				pinctrl-0 = <&panel_te_pin &panel_rst_pin>;
-
-				iovdd-supply = <&pma8084_lvs4>;
-				vddr-supply = <&vreg_panel>;
-
-				reset-gpios = <&pma8084_gpios 17 GPIO_ACTIVE_LOW>;
-				te-gpios = <&msmgpio 12 GPIO_ACTIVE_HIGH>;
-
-				port {
-					panel_in: endpoint {
-						remote-endpoint = <&dsi0_out>;
-					};
-				};
-			};
-		};
-
-		dsi-phy@fd922a00 {
-			status = "ok";
-
-			vddio-supply = <&pma8084_l12>;
-		};
-	};
-
-	remoteproc@fc880000 {
-		cx-supply = <&pma8084_s2>;
-		mss-supply = <&pma8084_s6>;
-		mx-supply = <&pma8084_s1>;
-		pll-supply = <&pma8084_l12>;
-	};
-};
-
-&spmi_bus {
-	pma8084@0 {
-		gpios@c000 {
-			gpio_keys_pin_a: gpio-keys-active {
-				pins = "gpio2", "gpio3", "gpio5";
-				function = "normal";
-
-				bias-pull-up;
-				power-source = <PMA8084_GPIO_S4>;
-			};
-
-			touchkey_pin: touchkey-int-pin {
-				pins = "gpio6";
-				function = "normal";
-				bias-disable;
-				input-enable;
-				power-source = <PMA8084_GPIO_S4>;
-			};
-
-			touch_pin: touchscreen-int-pin {
-				pins = "gpio8";
-				function = "normal";
-				bias-disable;
-				input-enable;
-				power-source = <PMA8084_GPIO_S4>;
-			};
-
-			panel_en_pin: panel-en-pin {
-				pins = "gpio14";
-				function = "normal";
-				bias-pull-up;
-				power-source = <PMA8084_GPIO_S4>;
-				qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
-			};
-
-			wlan_sleep_clk_pin: wlan-sleep-clk-pin {
-				pins = "gpio16";
-				function = "func2";
-
-				output-high;
-				power-source = <PMA8084_GPIO_S4>;
-				qcom,drive-strength = <PMIC_GPIO_STRENGTH_HIGH>;
-			};
-
-			panel_rst_pin: panel-rst-pin {
-				pins = "gpio17";
-				function = "normal";
-				bias-disable;
-				power-source = <PMA8084_GPIO_S4>;
-				qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
-			};
-
-
-			fuelgauge_pin: fuelgauge-int-pin {
-				pins = "gpio21";
-				function = "normal";
-				bias-disable;
-				input-enable;
-				power-source = <PMA8084_GPIO_S4>;
-			};
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/qcom-msm8974-sony-xperia-amami.dts b/arch/arm/boot/dts/qcom-msm8974-sony-xperia-amami.dts
deleted file mode 100644
index 398a3eaf306b..000000000000
--- a/arch/arm/boot/dts/qcom-msm8974-sony-xperia-amami.dts
+++ /dev/null
@@ -1,436 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-#include "qcom-msm8974.dtsi"
-#include "qcom-pm8841.dtsi"
-#include "qcom-pm8941.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
-
-/ {
-	model = "Sony Xperia Z1 Compact";
-	compatible = "sony,xperia-amami", "qcom,msm8974";
-
-	aliases {
-		serial0 = &blsp1_uart2;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	gpio-keys {
-		compatible = "gpio-keys";
-		input-name = "gpio-keys";
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&gpio_keys_pin_a>;
-
-		volume-down {
-			label = "volume_down";
-			gpios = <&pm8941_gpios 2 GPIO_ACTIVE_LOW>;
-			linux,input-type = <1>;
-			linux,code = <KEY_VOLUMEDOWN>;
-		};
-
-		camera-snapshot {
-			label = "camera_snapshot";
-			gpios = <&pm8941_gpios 3 GPIO_ACTIVE_LOW>;
-			linux,input-type = <1>;
-			linux,code = <KEY_CAMERA>;
-		};
-
-		camera-focus {
-			label = "camera_focus";
-			gpios = <&pm8941_gpios 4 GPIO_ACTIVE_LOW>;
-			linux,input-type = <1>;
-			linux,code = <KEY_CAMERA_FOCUS>;
-		};
-
-		volume-up {
-			label = "volume_up";
-			gpios = <&pm8941_gpios 5 GPIO_ACTIVE_LOW>;
-			linux,input-type = <1>;
-			linux,code = <KEY_VOLUMEUP>;
-		};
-	};
-
-	memory@0 {
-		reg = <0 0x40000000>, <0x40000000 0x40000000>;
-		device_type = "memory";
-	};
-
-	smd {
-		rpm {
-			rpm_requests {
-				pm8841-regulators {
-					s1 {
-						regulator-min-microvolt = <675000>;
-						regulator-max-microvolt = <1050000>;
-					};
-
-					s2 {
-						regulator-min-microvolt = <500000>;
-						regulator-max-microvolt = <1050000>;
-					};
-
-					s3 {
-						regulator-min-microvolt = <500000>;
-						regulator-max-microvolt = <1050000>;
-					};
-
-					s4 {
-						regulator-min-microvolt = <500000>;
-						regulator-max-microvolt = <1050000>;
-					};
-				};
-
-				pm8941-regulators {
-					vdd_l1_l3-supply = <&pm8941_s1>;
-					vdd_l2_lvs1_2_3-supply = <&pm8941_s3>;
-					vdd_l4_l11-supply = <&pm8941_s1>;
-					vdd_l5_l7-supply = <&pm8941_s2>;
-					vdd_l6_l12_l14_l15-supply = <&pm8941_s2>;
-					vdd_l9_l10_l17_l22-supply = <&vreg_boost>;
-					vdd_l13_l20_l23_l24-supply = <&vreg_boost>;
-					vdd_l21-supply = <&vreg_boost>;
-
-					s1 {
-						regulator-min-microvolt = <1300000>;
-						regulator-max-microvolt = <1300000>;
-						regulator-always-on;
-						regulator-boot-on;
-					};
-
-					s2 {
-						regulator-min-microvolt = <2150000>;
-						regulator-max-microvolt = <2150000>;
-						regulator-boot-on;
-					};
-
-					s3 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-						regulator-always-on;
-						regulator-boot-on;
-					};
-
-					s4 {
-						regulator-min-microvolt = <5000000>;
-						regulator-max-microvolt = <5000000>;
-					};
-
-					l1 {
-						regulator-min-microvolt = <1225000>;
-						regulator-max-microvolt = <1225000>;
-
-						regulator-always-on;
-						regulator-boot-on;
-					};
-
-					l2 {
-						regulator-min-microvolt = <1200000>;
-						regulator-max-microvolt = <1200000>;
-					};
-
-					l3 {
-						regulator-min-microvolt = <1200000>;
-						regulator-max-microvolt = <1200000>;
-					};
-
-					l4 {
-						regulator-min-microvolt = <1225000>;
-						regulator-max-microvolt = <1225000>;
-					};
-
-					l5 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-					};
-
-					l6 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-
-						regulator-boot-on;
-					};
-
-					l7 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-
-						regulator-boot-on;
-					};
-
-					l8 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-					};
-
-					l9 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <2950000>;
-					};
-
-					l11 {
-						regulator-min-microvolt = <1300000>;
-						regulator-max-microvolt = <1350000>;
-					};
-
-					l12 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-
-						regulator-always-on;
-						regulator-boot-on;
-					};
-
-					l13 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <2950000>;
-
-						regulator-boot-on;
-					};
-
-					l14 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-					};
-
-					l15 {
-						regulator-min-microvolt = <2050000>;
-						regulator-max-microvolt = <2050000>;
-					};
-
-					l16 {
-						regulator-min-microvolt = <2700000>;
-						regulator-max-microvolt = <2700000>;
-					};
-
-					l17 {
-						regulator-min-microvolt = <2700000>;
-						regulator-max-microvolt = <2700000>;
-					};
-
-					l18 {
-						regulator-min-microvolt = <2850000>;
-						regulator-max-microvolt = <2850000>;
-					};
-
-					l19 {
-						regulator-min-microvolt = <3300000>;
-						regulator-max-microvolt = <3300000>;
-					};
-
-					l20 {
-						regulator-min-microvolt = <2950000>;
-						regulator-max-microvolt = <2950000>;
-
-						regulator-allow-set-load;
-						regulator-boot-on;
-						regulator-system-load = <200000>;
-					};
-
-					l21 {
-						regulator-min-microvolt = <2950000>;
-						regulator-max-microvolt = <2950000>;
-
-						regulator-boot-on;
-					};
-
-					l22 {
-						regulator-min-microvolt = <3000000>;
-						regulator-max-microvolt = <3000000>;
-					};
-
-					l23 {
-						regulator-min-microvolt = <2800000>;
-						regulator-max-microvolt = <2800000>;
-					};
-
-					l24 {
-						regulator-min-microvolt = <3075000>;
-						regulator-max-microvolt = <3075000>;
-
-						regulator-boot-on;
-					};
-				};
-			};
-		};
-	};
-};
-
-&soc {
-	sdhci@f9824900 {
-		status = "okay";
-
-		vmmc-supply = <&pm8941_l20>;
-		vqmmc-supply = <&pm8941_s3>;
-
-		bus-width = <8>;
-		non-removable;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&sdhc1_pin_a>;
-	};
-
-	sdhci@f98a4900 {
-		status = "okay";
-
-		bus-width = <4>;
-
-		vmmc-supply = <&pm8941_l21>;
-		vqmmc-supply = <&pm8941_l13>;
-
-		cd-gpios = <&msmgpio 62 GPIO_ACTIVE_LOW>;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&sdhc2_pin_a>, <&sdhc2_cd_pin_a>;
-	};
-
-	serial@f991e000 {
-		status = "okay";
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&blsp1_uart2_pin_a>;
-	};
-
-
-	pinctrl@fd510000 {
-		blsp1_uart2_pin_a: blsp1-uart2-pin-active {
-			rx {
-				pins = "gpio5";
-				function = "blsp_uart2";
-
-				drive-strength = <2>;
-				bias-pull-up;
-			};
-
-			tx {
-				pins = "gpio4";
-				function = "blsp_uart2";
-
-				drive-strength = <4>;
-				bias-disable;
-			};
-		};
-
-		i2c2_pins: i2c2 {
-			mux {
-				pins = "gpio6", "gpio7";
-				function = "blsp_i2c2";
-
-				drive-strength = <2>;
-				bias-disable;
-			};
-		};
-
-		sdhc1_pin_a: sdhc1-pin-active {
-			clk {
-				pins = "sdc1_clk";
-				drive-strength = <16>;
-				bias-disable;
-			};
-
-			cmd-data {
-				pins = "sdc1_cmd", "sdc1_data";
-				drive-strength = <10>;
-				bias-pull-up;
-			};
-		};
-
-		sdhc2_cd_pin_a: sdhc2-cd-pin-active {
-			pins = "gpio62";
-			function = "gpio";
-
-			drive-strength = <2>;
-			bias-disable;
-		 };
-
-		sdhc2_pin_a: sdhc2-pin-active {
-			clk {
-				pins = "sdc2_clk";
-				drive-strength = <10>;
-				bias-disable;
-			};
-
-			cmd-data {
-				pins = "sdc2_cmd", "sdc2_data";
-				drive-strength = <6>;
-				bias-pull-up;
-			};
-		};
-	};
-
-	dma-controller@f9944000 {
-		qcom,controlled-remotely;
-	};
-
-	usb@f9a55000 {
-		status = "okay";
-
-		phys = <&usb_hs1_phy>;
-		phy-select = <&tcsr 0xb000 0>;
-		extcon = <&smbb>, <&usb_id>;
-		vbus-supply = <&chg_otg>;
-
-		hnp-disable;
-		srp-disable;
-		adp-disable;
-
-		ulpi {
-			phy@a {
-				status = "okay";
-
-				v1p8-supply = <&pm8941_l6>;
-				v3p3-supply = <&pm8941_l24>;
-
-				extcon = <&smbb>;
-				qcom,init-seq = /bits/ 8 <0x1 0x64>;
-			};
-		};
-	};
-};
-
-&spmi_bus {
-	pm8941@0 {
-		charger@1000 {
-			qcom,fast-charge-safe-current = <1300000>;
-			qcom,fast-charge-current-limit = <1300000>;
-			qcom,dc-current-limit = <1300000>;
-			qcom,fast-charge-safe-voltage = <4400000>;
-			qcom,fast-charge-high-threshold-voltage = <4350000>;
-			qcom,fast-charge-low-threshold-voltage = <3400000>;
-			qcom,auto-recharge-threshold-voltage = <4200000>;
-			qcom,minimum-input-voltage = <4300000>;
-		};
-
-		gpios@c000 {
-			gpio_keys_pin_a: gpio-keys-active {
-				pins = "gpio2", "gpio3", "gpio4", "gpio5";
-				function = "normal";
-
-				bias-pull-up;
-				power-source = <PM8941_GPIO_S3>;
-			};
-		};
-
-		coincell@2800 {
-			status = "okay";
-			qcom,rset-ohms = <2100>;
-			qcom,vset-millivolts = <3000>;
-		};
-	};
-
-	pm8941@1 {
-		wled@d800 {
-			status = "okay";
-
-			qcom,cs-out;
-			qcom,current-limit = <20>;
-			qcom,current-boost-limit = <805>;
-			qcom,switching-freq = <1600>;
-			qcom,ovp = <29>;
-			qcom,num-strings = <2>;
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/qcom-msm8974-sony-xperia-castor.dts b/arch/arm/boot/dts/qcom-msm8974-sony-xperia-castor.dts
deleted file mode 100644
index b4dd85bd4faf..000000000000
--- a/arch/arm/boot/dts/qcom-msm8974-sony-xperia-castor.dts
+++ /dev/null
@@ -1,724 +0,0 @@
-#include "qcom-msm8974pro.dtsi"
-#include "qcom-pm8841.dtsi"
-#include "qcom-pm8941.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
-
-/ {
-	model = "Sony Xperia Z2 Tablet";
-	compatible = "sony,xperia-castor", "qcom,msm8974";
-
-	aliases {
-		serial0 = &blsp1_uart2;
-		serial1 = &blsp2_uart7;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	gpio-keys {
-		compatible = "gpio-keys";
-		input-name = "gpio-keys";
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&gpio_keys_pin_a>;
-
-		volume-down {
-			label = "volume_down";
-			gpios = <&pm8941_gpios 2 GPIO_ACTIVE_LOW>;
-			linux,input-type = <1>;
-			linux,code = <KEY_VOLUMEDOWN>;
-		};
-
-		camera-snapshot {
-			label = "camera_snapshot";
-			gpios = <&pm8941_gpios 3 GPIO_ACTIVE_LOW>;
-			linux,input-type = <1>;
-			linux,code = <KEY_CAMERA>;
-		};
-
-		camera-focus {
-			label = "camera_focus";
-			gpios = <&pm8941_gpios 4 GPIO_ACTIVE_LOW>;
-			linux,input-type = <1>;
-			linux,code = <KEY_CAMERA_FOCUS>;
-		};
-
-		volume-up {
-			label = "volume_up";
-			gpios = <&pm8941_gpios 5 GPIO_ACTIVE_LOW>;
-			linux,input-type = <1>;
-			linux,code = <KEY_VOLUMEUP>;
-		};
-	};
-
-	smd {
-		rpm {
-			rpm_requests {
-				pm8941-regulators {
-					vdd_l1_l3-supply = <&pm8941_s1>;
-					vdd_l2_lvs1_2_3-supply = <&pm8941_s3>;
-					vdd_l4_l11-supply = <&pm8941_s1>;
-					vdd_l5_l7-supply = <&pm8941_s2>;
-					vdd_l6_l12_l14_l15-supply = <&pm8941_s2>;
-					vdd_l9_l10_l17_l22-supply = <&vreg_boost>;
-					vdd_l13_l20_l23_l24-supply = <&vreg_boost>;
-					vdd_l21-supply = <&vreg_boost>;
-
-					s1 {
-						regulator-min-microvolt = <1300000>;
-						regulator-max-microvolt = <1300000>;
-						regulator-always-on;
-						regulator-boot-on;
-					};
-
-					s2 {
-						regulator-min-microvolt = <2150000>;
-						regulator-max-microvolt = <2150000>;
-						regulator-boot-on;
-					};
-
-					s3 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-						regulator-always-on;
-						regulator-boot-on;
-
-						regulator-system-load = <154000>;
-					};
-
-					s4 {
-						regulator-min-microvolt = <5000000>;
-						regulator-max-microvolt = <5000000>;
-					};
-
-					l1 {
-						regulator-min-microvolt = <1225000>;
-						regulator-max-microvolt = <1225000>;
-
-						regulator-always-on;
-						regulator-boot-on;
-					};
-
-					l2 {
-						regulator-min-microvolt = <1200000>;
-						regulator-max-microvolt = <1200000>;
-					};
-
-					l3 {
-						regulator-min-microvolt = <1200000>;
-						regulator-max-microvolt = <1200000>;
-					};
-
-					l4 {
-						regulator-min-microvolt = <1225000>;
-						regulator-max-microvolt = <1225000>;
-					};
-
-					l5 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-					};
-
-					l6 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-
-						regulator-boot-on;
-					};
-
-					l7 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-
-						regulator-boot-on;
-					};
-
-					l8 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-					};
-
-					l9 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <2950000>;
-					};
-
-					l11 {
-						regulator-min-microvolt = <1300000>;
-						regulator-max-microvolt = <1350000>;
-					};
-
-					l12 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-
-						regulator-always-on;
-						regulator-boot-on;
-					};
-
-					l13 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <2950000>;
-
-						regulator-boot-on;
-					};
-
-					l14 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-					};
-
-					l15 {
-						regulator-min-microvolt = <2050000>;
-						regulator-max-microvolt = <2050000>;
-					};
-
-					l16 {
-						regulator-min-microvolt = <2700000>;
-						regulator-max-microvolt = <2700000>;
-					};
-
-					l17 {
-						regulator-min-microvolt = <2700000>;
-						regulator-max-microvolt = <2700000>;
-					};
-
-					l18 {
-						regulator-min-microvolt = <2850000>;
-						regulator-max-microvolt = <2850000>;
-					};
-
-					l19 {
-						regulator-min-microvolt = <2850000>;
-						regulator-max-microvolt = <2850000>;
-					};
-
-					l20 {
-						regulator-min-microvolt = <2950000>;
-						regulator-max-microvolt = <2950000>;
-
-						regulator-allow-set-load;
-						regulator-boot-on;
-						regulator-allow-set-load;
-						regulator-system-load = <500000>;
-					};
-
-					l21 {
-						regulator-min-microvolt = <2950000>;
-						regulator-max-microvolt = <2950000>;
-
-						regulator-boot-on;
-					};
-
-					l22 {
-						regulator-min-microvolt = <3000000>;
-						regulator-max-microvolt = <3000000>;
-					};
-
-					l23 {
-						regulator-min-microvolt = <2800000>;
-						regulator-max-microvolt = <2800000>;
-					};
-
-					l24 {
-						regulator-min-microvolt = <3075000>;
-						regulator-max-microvolt = <3075000>;
-
-						regulator-boot-on;
-					};
-				};
-			};
-		};
-	};
-
-	vreg_bl_vddio: lcd-backlight-vddio {
-		compatible = "regulator-fixed";
-		regulator-name = "vreg_bl_vddio";
-		regulator-min-microvolt = <3150000>;
-		regulator-max-microvolt = <3150000>;
-
-		gpio = <&msmgpio 69 0>;
-		enable-active-high;
-
-		vin-supply = <&pm8941_s3>;
-		startup-delay-us = <70000>;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&lcd_backlight_en_pin_a>;
-	};
-
-	vreg_vsp: lcd-dcdc-regulator {
-		compatible = "regulator-fixed";
-		regulator-name = "vreg_vsp";
-		regulator-min-microvolt = <5600000>;
-		regulator-max-microvolt = <5600000>;
-
-		gpio = <&pm8941_gpios 20 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&lcd_dcdc_en_pin_a>;
-	};
-
-	vreg_wlan: wlan-regulator {
-		compatible = "regulator-fixed";
-
-		regulator-name = "wl-reg";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-
-		gpio = <&pm8941_gpios 18 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&wlan_regulator_pin>;
-	};
-};
-
-&soc {
-	sdhci@f9824900 {
-		status = "okay";
-
-		vmmc-supply = <&pm8941_l20>;
-		vqmmc-supply = <&pm8941_s3>;
-
-		bus-width = <8>;
-		non-removable;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&sdhc1_pin_a>;
-	};
-
-	sdhci@f9864900 {
-		status = "okay";
-
-		max-frequency = <100000000>;
-		non-removable;
-		vmmc-supply = <&vreg_wlan>;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&sdhc3_pin_a>;
-
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		bcrmf@1 {
-			compatible = "brcm,bcm4339-fmac", "brcm,bcm4329-fmac";
-			reg = <1>;
-
-			brcm,drive-strength = <10>;
-
-			pinctrl-names = "default";
-			pinctrl-0 = <&wlan_sleep_clk_pin>;
-		};
-	};
-
-	sdhci@f98a4900 {
-		status = "okay";
-
-		bus-width = <4>;
-
-		vmmc-supply = <&pm8941_l21>;
-		vqmmc-supply = <&pm8941_l13>;
-
-		cd-gpios = <&msmgpio 62 GPIO_ACTIVE_LOW>;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&sdhc2_pin_a>, <&sdhc2_cd_pin_a>;
-	};
-
-	serial@f991e000 {
-		status = "okay";
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&blsp1_uart2_pin_a>;
-	};
-
-	serial@f995d000 {
-		status = "ok";
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&blsp2_uart7_pin_a>;
-
-		bluetooth {
-			compatible = "brcm,bcm43438-bt";
-			max-speed = <3000000>;
-
-			pinctrl-names = "default";
-			pinctrl-0 = <&bt_host_wake_pin>,
-				    <&bt_dev_wake_pin>,
-				    <&bt_reg_on_pin>;
-
-			host-wakeup-gpios = <&msmgpio 95 GPIO_ACTIVE_HIGH>;
-			device-wakeup-gpios = <&msmgpio 96 GPIO_ACTIVE_HIGH>;
-			shutdown-gpios = <&pm8941_gpios 16 GPIO_ACTIVE_HIGH>;
-		};
-	};
-
-	usb@f9a55000 {
-		status = "okay";
-
-		phys = <&usb_hs1_phy>;
-		phy-select = <&tcsr 0xb000 0>;
-		extcon = <&smbb>, <&usb_id>;
-		vbus-supply = <&chg_otg>;
-
-		hnp-disable;
-		srp-disable;
-		adp-disable;
-
-		ulpi {
-			phy@a {
-				status = "okay";
-
-				v1p8-supply = <&pm8941_l6>;
-				v3p3-supply = <&pm8941_l24>;
-
-				extcon = <&smbb>;
-				qcom,init-seq = /bits/ 8 <0x1 0x64>;
-			};
-		};
-	};
-
-	pinctrl@fd510000 {
-		blsp1_uart2_pin_a: blsp1-uart2-pin-active {
-			rx {
-				pins = "gpio5";
-				function = "blsp_uart2";
-
-				drive-strength = <2>;
-				bias-pull-up;
-			};
-
-			tx {
-				pins = "gpio4";
-				function = "blsp_uart2";
-
-				drive-strength = <4>;
-				bias-disable;
-			};
-		};
-
-		blsp2_uart7_pin_a: blsp2-uart7-pin-active {
-			tx {
-				pins = "gpio41";
-				function = "blsp_uart7";
-
-				drive-strength = <2>;
-				bias-disable;
-			};
-
-			rx {
-				pins = "gpio42";
-				function = "blsp_uart7";
-
-				drive-strength = <2>;
-				bias-pull-up;
-			};
-
-			cts {
-				pins = "gpio43";
-				function = "blsp_uart7";
-
-				drive-strength = <2>;
-				bias-pull-up;
-			};
-
-			rts {
-				pins = "gpio44";
-				function = "blsp_uart7";
-
-				drive-strength = <2>;
-				bias-disable;
-			};
-		};
-
-		i2c8_pins: i2c8 {
-			mux {
-				pins = "gpio47", "gpio48";
-				function = "blsp_i2c8";
-
-				drive-strength = <2>;
-				bias-disable;
-			};
-		};
-
-		i2c11_pins: i2c11 {
-			mux {
-				pins = "gpio83", "gpio84";
-				function = "blsp_i2c11";
-
-				drive-strength = <2>;
-				bias-disable;
-			};
-		};
-
-		lcd_backlight_en_pin_a: lcd-backlight-vddio {
-			pins = "gpio69";
-			drive-strength = <10>;
-			output-low;
-			bias-disable;
-		};
-
-		sdhc1_pin_a: sdhc1-pin-active {
-			clk {
-				pins = "sdc1_clk";
-				drive-strength = <16>;
-				bias-disable;
-			};
-
-			cmd-data {
-				pins = "sdc1_cmd", "sdc1_data";
-				drive-strength = <10>;
-				bias-pull-up;
-			};
-		};
-
-		sdhc2_cd_pin_a: sdhc2-cd-pin-active {
-			pins = "gpio62";
-			function = "gpio";
-
-			drive-strength = <2>;
-			bias-disable;
-		 };
-
-		sdhc2_pin_a: sdhc2-pin-active {
-			clk {
-				pins = "sdc2_clk";
-				drive-strength = <6>;
-				bias-disable;
-			};
-
-			cmd-data {
-				pins = "sdc2_cmd", "sdc2_data";
-				drive-strength = <6>;
-				bias-pull-up;
-			};
-		};
-
-		sdhc3_pin_a: sdhc3-pin-active {
-			clk {
-				pins = "gpio40";
-				function = "sdc3";
-
-				drive-strength = <10>;
-				bias-disable;
-			};
-
-			cmd {
-				pins = "gpio39";
-				function = "sdc3";
-
-				drive-strength = <10>;
-				bias-pull-up;
-			};
-
-			data {
-				pins = "gpio35", "gpio36", "gpio37", "gpio38";
-				function = "sdc3";
-
-				drive-strength = <10>;
-				bias-pull-up;
-			};
-		};
-
-		ts_int_pin: synaptics {
-			pin {
-				pins = "gpio86";
-				function = "gpio";
-
-				drive-strength = <2>;
-				bias-disable;
-				input-enable;
-			};
-		};
-
-		bt_host_wake_pin: bt-host-wake {
-			pins = "gpio95";
-			function = "gpio";
-
-			drive-strength = <2>;
-			bias-disable;
-			output-low;
-		};
-
-		bt_dev_wake_pin: bt-dev-wake {
-			pins = "gpio96";
-			function = "gpio";
-
-			drive-strength = <2>;
-			bias-disable;
-		};
-	};
-
-	i2c@f9964000 {
-		status = "okay";
-
-		clock-frequency = <355000>;
-		qcom,src-freq = <50000000>;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&i2c8_pins>;
-
-		synaptics@2c {
-			compatible = "syna,rmi4-i2c";
-			reg = <0x2c>;
-
-			interrupt-parent = <&msmgpio>;
-			interrupts = <86 IRQ_TYPE_EDGE_FALLING>;
-
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			vdd-supply = <&pm8941_l22>;
-			vio-supply = <&pm8941_lvs3>;
-
-			pinctrl-names = "default";
-			pinctrl-0 = <&ts_int_pin>;
-
-			syna,startup-delay-ms = <10>;
-
-			rmi-f01@1 {
-				reg = <0x1>;
-				syna,nosleep = <1>;
-			};
-
-			rmi-f11@11 {
-				reg = <0x11>;
-				syna,f11-flip-x = <1>;
-				syna,sensor-type = <1>;
-			};
-		};
-	};
-
-	i2c@f9967000 {
-		status = "okay";
-		pinctrl-names = "default";
-		pinctrl-0 = <&i2c11_pins>;
-		clock-frequency = <355000>;
-		qcom,src-freq = <50000000>;
-
-		lp8566_wled: backlight@2c {
-			compatible = "ti,lp8556";
-			reg = <0x2c>;
-			power-supply = <&vreg_bl_vddio>;
-
-			bl-name = "backlight";
-			dev-ctrl = /bits/ 8 <0x05>;
-			init-brt = /bits/ 8 <0x3f>;
-			rom_a0h {
-				rom-addr = /bits/ 8 <0xa0>;
-				rom-val = /bits/ 8 <0xff>;
-			};
-			rom_a1h {
-				rom-addr = /bits/ 8 <0xa1>;
-				rom-val = /bits/ 8 <0x3f>;
-			};
-			rom_a2h {
-				rom-addr = /bits/ 8 <0xa2>;
-				rom-val = /bits/ 8 <0x20>;
-			};
-			rom_a3h {
-				rom-addr = /bits/ 8 <0xa3>;
-				rom-val = /bits/ 8 <0x5e>;
-			};
-			rom_a4h {
-				rom-addr = /bits/ 8 <0xa4>;
-				rom-val = /bits/ 8 <0x02>;
-			};
-			rom_a5h {
-				rom-addr = /bits/ 8 <0xa5>;
-				rom-val = /bits/ 8 <0x04>;
-			};
-			rom_a6h {
-				rom-addr = /bits/ 8 <0xa6>;
-				rom-val = /bits/ 8 <0x80>;
-			};
-			rom_a7h {
-				rom-addr = /bits/ 8 <0xa7>;
-				rom-val = /bits/ 8 <0xf7>;
-			};
-			rom_a9h {
-				rom-addr = /bits/ 8 <0xa9>;
-				rom-val = /bits/ 8 <0x80>;
-			};
-			rom_aah {
-				rom-addr = /bits/ 8 <0xaa>;
-				rom-val = /bits/ 8 <0x0f>;
-			};
-			rom_aeh {
-				rom-addr = /bits/ 8 <0xae>;
-				rom-val = /bits/ 8 <0x0f>;
-			};
-		};
-	};
-};
-
-&spmi_bus {
-	pm8941@0 {
-		charger@1000 {
-			qcom,fast-charge-safe-current = <1500000>;
-			qcom,fast-charge-current-limit = <1500000>;
-			qcom,dc-current-limit = <1800000>;
-			qcom,fast-charge-safe-voltage = <4400000>;
-			qcom,fast-charge-high-threshold-voltage = <4350000>;
-			qcom,fast-charge-low-threshold-voltage = <3400000>;
-			qcom,auto-recharge-threshold-voltage = <4200000>;
-			qcom,minimum-input-voltage = <4300000>;
-		};
-
-		gpios@c000 {
-			gpio_keys_pin_a: gpio-keys-active {
-				pins = "gpio2", "gpio5";
-				function = "normal";
-
-				bias-pull-up;
-				power-source = <PM8941_GPIO_S3>;
-			};
-
-			bt_reg_on_pin: bt-reg-on {
-				pins = "gpio16";
-				function = "normal";
-
-				output-low;
-				power-source = <PM8941_GPIO_S3>;
-			};
-
-			wlan_sleep_clk_pin: wl-sleep-clk {
-				pins = "gpio17";
-				function = "func2";
-
-				output-high;
-				power-source = <PM8941_GPIO_S3>;
-			};
-
-			wlan_regulator_pin: wl-reg-active {
-				pins = "gpio18";
-				function = "normal";
-
-				bias-disable;
-				power-source = <PM8941_GPIO_S3>;
-			};
-
-			lcd_dcdc_en_pin_a: lcd-dcdc-en-active {
-				pins = "gpio20";
-				function = "normal";
-
-				bias-disable;
-				power-source = <PM8941_GPIO_S3>;
-				input-disable;
-				output-low;
-			};
-
-		};
-
-		coincell@2800 {
-			status = "okay";
-			qcom,rset-ohms = <2100>;
-			qcom,vset-millivolts = <3000>;
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/qcom-msm8974-sony-xperia-honami.dts b/arch/arm/boot/dts/qcom-msm8974-sony-xperia-honami.dts
deleted file mode 100644
index 9743beebd84d..000000000000
--- a/arch/arm/boot/dts/qcom-msm8974-sony-xperia-honami.dts
+++ /dev/null
@@ -1,485 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-#include "qcom-msm8974.dtsi"
-#include "qcom-pm8841.dtsi"
-#include "qcom-pm8941.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
-
-/ {
-	model = "Sony Xperia Z1";
-	compatible = "sony,xperia-honami", "qcom,msm8974";
-
-	aliases {
-		serial0 = &blsp1_uart2;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	gpio-keys {
-		compatible = "gpio-keys";
-		input-name = "gpio-keys";
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&gpio_keys_pin_a>;
-
-		volume-down {
-			label = "volume_down";
-			gpios = <&pm8941_gpios 2 GPIO_ACTIVE_LOW>;
-			linux,input-type = <1>;
-			linux,code = <KEY_VOLUMEDOWN>;
-		};
-
-		camera-snapshot {
-			label = "camera_snapshot";
-			gpios = <&pm8941_gpios 3 GPIO_ACTIVE_LOW>;
-			linux,input-type = <1>;
-			linux,code = <KEY_CAMERA>;
-		};
-
-		camera-focus {
-			label = "camera_focus";
-			gpios = <&pm8941_gpios 4 GPIO_ACTIVE_LOW>;
-			linux,input-type = <1>;
-			linux,code = <KEY_CAMERA_FOCUS>;
-		};
-
-		volume-up {
-			label = "volume_up";
-			gpios = <&pm8941_gpios 5 GPIO_ACTIVE_LOW>;
-			linux,input-type = <1>;
-			linux,code = <KEY_VOLUMEUP>;
-		};
-	};
-
-	memory@0 {
-		reg = <0 0x40000000>, <0x40000000 0x40000000>;
-		device_type = "memory";
-	};
-
-	smd {
-		rpm {
-			rpm_requests {
-				pm8841-regulators {
-					s1 {
-						regulator-min-microvolt = <675000>;
-						regulator-max-microvolt = <1050000>;
-					};
-
-					s2 {
-						regulator-min-microvolt = <500000>;
-						regulator-max-microvolt = <1050000>;
-					};
-
-					s3 {
-						regulator-min-microvolt = <500000>;
-						regulator-max-microvolt = <1050000>;
-					};
-
-					s4 {
-						regulator-min-microvolt = <500000>;
-						regulator-max-microvolt = <1050000>;
-					};
-				};
-
-				pm8941-regulators {
-					vdd_l1_l3-supply = <&pm8941_s1>;
-					vdd_l2_lvs1_2_3-supply = <&pm8941_s3>;
-					vdd_l4_l11-supply = <&pm8941_s1>;
-					vdd_l5_l7-supply = <&pm8941_s2>;
-					vdd_l6_l12_l14_l15-supply = <&pm8941_s2>;
-					vdd_l9_l10_l17_l22-supply = <&vreg_boost>;
-					vdd_l13_l20_l23_l24-supply = <&vreg_boost>;
-					vdd_l21-supply = <&vreg_boost>;
-
-					s1 {
-						regulator-min-microvolt = <1300000>;
-						regulator-max-microvolt = <1300000>;
-						regulator-always-on;
-						regulator-boot-on;
-					};
-
-					s2 {
-						regulator-min-microvolt = <2150000>;
-						regulator-max-microvolt = <2150000>;
-						regulator-boot-on;
-					};
-
-					s3 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-						regulator-always-on;
-						regulator-boot-on;
-					};
-
-					s4 {
-						regulator-min-microvolt = <5000000>;
-						regulator-max-microvolt = <5000000>;
-					};
-
-					l1 {
-						regulator-min-microvolt = <1225000>;
-						regulator-max-microvolt = <1225000>;
-
-						regulator-always-on;
-						regulator-boot-on;
-					};
-
-					l2 {
-						regulator-min-microvolt = <1200000>;
-						regulator-max-microvolt = <1200000>;
-					};
-
-					l3 {
-						regulator-min-microvolt = <1200000>;
-						regulator-max-microvolt = <1200000>;
-					};
-
-					l4 {
-						regulator-min-microvolt = <1225000>;
-						regulator-max-microvolt = <1225000>;
-					};
-
-					l5 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-					};
-
-					l6 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-
-						regulator-boot-on;
-					};
-
-					l7 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-
-						regulator-boot-on;
-					};
-
-					l8 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-					};
-
-					l9 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <2950000>;
-					};
-
-					l11 {
-						regulator-min-microvolt = <1300000>;
-						regulator-max-microvolt = <1350000>;
-					};
-
-					l12 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-
-						regulator-always-on;
-						regulator-boot-on;
-					};
-
-					l13 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <2950000>;
-
-						regulator-boot-on;
-					};
-
-					l14 {
-						regulator-min-microvolt = <1800000>;
-						regulator-max-microvolt = <1800000>;
-					};
-
-					l15 {
-						regulator-min-microvolt = <2050000>;
-						regulator-max-microvolt = <2050000>;
-					};
-
-					l16 {
-						regulator-min-microvolt = <2700000>;
-						regulator-max-microvolt = <2700000>;
-					};
-
-					l17 {
-						regulator-min-microvolt = <2700000>;
-						regulator-max-microvolt = <2700000>;
-					};
-
-					l18 {
-						regulator-min-microvolt = <2850000>;
-						regulator-max-microvolt = <2850000>;
-					};
-
-					l19 {
-						regulator-min-microvolt = <3300000>;
-						regulator-max-microvolt = <3300000>;
-					};
-
-					l20 {
-						regulator-min-microvolt = <2950000>;
-						regulator-max-microvolt = <2950000>;
-
-						regulator-allow-set-load;
-						regulator-boot-on;
-						regulator-system-load = <200000>;
-					};
-
-					l21 {
-						regulator-min-microvolt = <2950000>;
-						regulator-max-microvolt = <2950000>;
-
-						regulator-boot-on;
-					};
-
-					l22 {
-						regulator-min-microvolt = <3000000>;
-						regulator-max-microvolt = <3000000>;
-					};
-
-					l23 {
-						regulator-min-microvolt = <2800000>;
-						regulator-max-microvolt = <2800000>;
-					};
-
-					l24 {
-						regulator-min-microvolt = <3075000>;
-						regulator-max-microvolt = <3075000>;
-
-						regulator-boot-on;
-					};
-				};
-			};
-		};
-	};
-};
-
-&soc {
-	usb@f9a55000 {
-		status = "okay";
-
-		phys = <&usb_hs1_phy>;
-		phy-select = <&tcsr 0xb000 0>;
-		extcon = <&smbb>, <&usb_id>;
-		vbus-supply = <&chg_otg>;
-
-		hnp-disable;
-		srp-disable;
-		adp-disable;
-
-		ulpi {
-			phy@a {
-				status = "okay";
-
-				v1p8-supply = <&pm8941_l6>;
-				v3p3-supply = <&pm8941_l24>;
-
-				extcon = <&smbb>;
-				qcom,init-seq = /bits/ 8 <0x1 0x64>;
-			};
-		};
-	};
-
-	sdhci@f9824900 {
-		status = "okay";
-
-		vmmc-supply = <&pm8941_l20>;
-		vqmmc-supply = <&pm8941_s3>;
-
-		bus-width = <8>;
-		non-removable;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&sdhc1_pin_a>;
-	};
-
-	sdhci@f98a4900 {
-		status = "okay";
-
-		bus-width = <4>;
-
-		vmmc-supply = <&pm8941_l21>;
-		vqmmc-supply = <&pm8941_l13>;
-
-		cd-gpios = <&msmgpio 62 GPIO_ACTIVE_LOW>;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&sdhc2_pin_a>, <&sdhc2_cd_pin_a>;
-	};
-
-	serial@f991e000 {
-		status = "okay";
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&blsp1_uart2_pin_a>;
-	};
-
-	i2c@f9924000 {
-		status = "okay";
-
-		clock-frequency = <355000>;
-		qcom,src-freq = <50000000>;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&i2c2_pins>;
-
-		synaptics@2c {
-			compatible = "syna,rmi4-i2c";
-			reg = <0x2c>;
-
-			interrupts-extended = <&msmgpio 61 IRQ_TYPE_EDGE_FALLING>;
-
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			vdd-supply = <&pm8941_l22>;
-			vio-supply = <&pm8941_lvs3>;
-
-			pinctrl-names = "default";
-			pinctrl-0 = <&ts_int_pin>;
-
-			syna,startup-delay-ms = <10>;
-
-			rmi4-f01@1 {
-				reg = <0x1>;
-				syna,nosleep-mode = <1>;
-			};
-
-			rmi4-f11@11 {
-				reg = <0x11>;
-				touchscreen-inverted-x;
-				syna,sensor-type = <1>;
-			};
-		};
-	};
-
-	pinctrl@fd510000 {
-		blsp1_uart2_pin_a: blsp1-uart2-pin-active {
-			rx {
-				pins = "gpio5";
-				function = "blsp_uart2";
-
-				drive-strength = <2>;
-				bias-pull-up;
-			};
-
-			tx {
-				pins = "gpio4";
-				function = "blsp_uart2";
-
-				drive-strength = <4>;
-				bias-disable;
-			};
-		};
-
-		i2c2_pins: i2c2 {
-			mux {
-				pins = "gpio6", "gpio7";
-				function = "blsp_i2c2";
-
-				drive-strength = <2>;
-				bias-disable;
-			};
-		};
-
-		sdhc1_pin_a: sdhc1-pin-active {
-			clk {
-				pins = "sdc1_clk";
-				drive-strength = <16>;
-				bias-disable;
-			};
-
-			cmd-data {
-				pins = "sdc1_cmd", "sdc1_data";
-				drive-strength = <10>;
-				bias-pull-up;
-			};
-		};
-
-		sdhc2_cd_pin_a: sdhc2-cd-pin-active {
-			pins = "gpio62";
-			function = "gpio";
-
-			drive-strength = <2>;
-			bias-disable;
-		 };
-
-		sdhc2_pin_a: sdhc2-pin-active {
-			clk {
-				pins = "sdc2_clk";
-				drive-strength = <10>;
-				bias-disable;
-			};
-
-			cmd-data {
-				pins = "sdc2_cmd", "sdc2_data";
-				drive-strength = <6>;
-				bias-pull-up;
-			};
-		};
-
-		ts_int_pin: touch-int {
-			pin {
-				pins = "gpio61";
-				function = "gpio";
-
-				drive-strength = <2>;
-				bias-disable;
-				input-enable;
-			};
-		};
-	};
-
-	dma-controller@f9944000 {
-		qcom,controlled-remotely;
-	};
-};
-
-&spmi_bus {
-	pm8941@0 {
-		charger@1000 {
-			qcom,fast-charge-safe-current = <1500000>;
-			qcom,fast-charge-current-limit = <1500000>;
-			qcom,dc-current-limit = <1800000>;
-			qcom,fast-charge-safe-voltage = <4400000>;
-			qcom,fast-charge-high-threshold-voltage = <4350000>;
-			qcom,fast-charge-low-threshold-voltage = <3400000>;
-			qcom,auto-recharge-threshold-voltage = <4200000>;
-			qcom,minimum-input-voltage = <4300000>;
-		};
-
-		gpios@c000 {
-			gpio_keys_pin_a: gpio-keys-active {
-				pins = "gpio2", "gpio3", "gpio4", "gpio5";
-				function = "normal";
-
-				bias-pull-up;
-				power-source = <PM8941_GPIO_S3>;
-			};
-		};
-
-		coincell@2800 {
-			status = "okay";
-			qcom,rset-ohms = <2100>;
-			qcom,vset-millivolts = <3000>;
-		};
-	};
-
-	pm8941@1 {
-		wled@d800 {
-			status = "okay";
-
-			qcom,cs-out;
-			qcom,current-limit = <20>;
-			qcom,current-boost-limit = <805>;
-			qcom,switching-freq = <1600>;
-			qcom,ovp = <29>;
-			qcom,num-strings = <2>;
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/qcom-msm8974-sony-xperia-rhine-amami.dts b/arch/arm/boot/dts/qcom-msm8974-sony-xperia-rhine-amami.dts
new file mode 100644
index 000000000000..68d5626bf491
--- /dev/null
+++ b/arch/arm/boot/dts/qcom-msm8974-sony-xperia-rhine-amami.dts
@@ -0,0 +1,13 @@
+// SPDX-License-Identifier: GPL-2.0
+#include "qcom-msm8974-sony-xperia-rhine.dtsi"
+
+/ {
+	model = "Sony Xperia Z1 Compact";
+	compatible = "sony,xperia-amami", "qcom,msm8974";
+};
+
+&smbb {
+	qcom,fast-charge-safe-current = <1300000>;
+	qcom,fast-charge-current-limit = <1300000>;
+	qcom,dc-current-limit = <1300000>;
+};
diff --git a/arch/arm/boot/dts/qcom-msm8974-sony-xperia-rhine-honami.dts b/arch/arm/boot/dts/qcom-msm8974-sony-xperia-rhine-honami.dts
new file mode 100644
index 000000000000..ea6a941d8f8c
--- /dev/null
+++ b/arch/arm/boot/dts/qcom-msm8974-sony-xperia-rhine-honami.dts
@@ -0,0 +1,7 @@
+// SPDX-License-Identifier: GPL-2.0
+#include "qcom-msm8974-sony-xperia-rhine.dtsi"
+
+/ {
+	model = "Sony Xperia Z1";
+	compatible = "sony,xperia-honami", "qcom,msm8974";
+};
diff --git a/arch/arm/boot/dts/qcom-msm8974-sony-xperia-rhine.dtsi b/arch/arm/boot/dts/qcom-msm8974-sony-xperia-rhine.dtsi
new file mode 100644
index 000000000000..5a70683d9103
--- /dev/null
+++ b/arch/arm/boot/dts/qcom-msm8974-sony-xperia-rhine.dtsi
@@ -0,0 +1,487 @@
+// SPDX-License-Identifier: GPL-2.0
+#include "qcom-msm8974.dtsi"
+#include "qcom-pm8841.dtsi"
+#include "qcom-pm8941.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+
+/ {
+	aliases {
+		serial0 = &blsp1_uart2;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_keys_pin_a>;
+
+		key-volume-down {
+			label = "volume_down";
+			gpios = <&pm8941_gpios 2 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			linux,code = <KEY_VOLUMEDOWN>;
+		};
+
+		key-camera-snapshot {
+			label = "camera_snapshot";
+			gpios = <&pm8941_gpios 3 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			linux,code = <KEY_CAMERA>;
+		};
+
+		key-camera-focus {
+			label = "camera_focus";
+			gpios = <&pm8941_gpios 4 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			linux,code = <KEY_CAMERA_FOCUS>;
+		};
+
+		key-volume-up {
+			label = "volume_up";
+			gpios = <&pm8941_gpios 5 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			linux,code = <KEY_VOLUMEUP>;
+		};
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		ramoops@3e8e0000 {
+			compatible = "ramoops";
+			reg = <0x3e8e0000 0x200000>;
+
+			console-size = <0x100000>;
+			record-size = <0x10000>;
+			ftrace-size = <0x10000>;
+			pmsg-size = <0x80000>;
+		};
+	};
+};
+
+&blsp1_i2c2 {
+	status = "okay";
+	clock-frequency = <355000>;
+
+	synaptics@2c {
+		compatible = "syna,rmi4-i2c";
+		reg = <0x2c>;
+
+		interrupts-extended = <&tlmm 61 IRQ_TYPE_EDGE_FALLING>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		vdd-supply = <&pm8941_l22>;
+		vio-supply = <&pm8941_lvs3>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&ts_int_pin>;
+
+		syna,startup-delay-ms = <10>;
+
+		rmi4-f01@1 {
+			reg = <0x1>;
+			syna,nosleep-mode = <1>;
+		};
+
+		rmi4-f11@11 {
+			reg = <0x11>;
+			touchscreen-inverted-x;
+			syna,sensor-type = <1>;
+		};
+	};
+};
+
+&blsp1_i2c6 {
+	status = "okay";
+	clock-frequency = <355000>;
+
+	nfc@28 {
+		compatible = "nxp,pn544-i2c";
+		reg = <0x28>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <59 IRQ_TYPE_EDGE_RISING>;
+
+		enable-gpios = <&pm8941_gpios 23 GPIO_ACTIVE_HIGH>;
+		firmware-gpios = <&tlmm 77 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&blsp1_uart2 {
+	status = "okay";
+};
+
+&blsp2_dma {
+	qcom,controlled-remotely;
+};
+
+&blsp2_i2c5 {
+	status = "okay";
+	clock-frequency = <355000>;
+
+	/* sii8334 MHL HDMI bridge */
+};
+
+&otg {
+	status = "okay";
+
+	phys = <&usb_hs1_phy>;
+	phy-select = <&tcsr 0xb000 0>;
+	extcon = <&smbb>, <&usb_id>;
+	vbus-supply = <&chg_otg>;
+
+	hnp-disable;
+	srp-disable;
+	adp-disable;
+
+	ulpi {
+		phy@a {
+			status = "okay";
+
+			v1p8-supply = <&pm8941_l6>;
+			v3p3-supply = <&pm8941_l24>;
+
+			extcon = <&smbb>;
+			qcom,init-seq = /bits/ 8 <0x1 0x64>;
+		};
+	};
+};
+
+&pm8941_coincell {
+	status = "okay";
+	qcom,rset-ohms = <2100>;
+	qcom,vset-millivolts = <3000>;
+};
+
+&pm8941_gpios {
+	gpio_keys_pin_a: gpio-keys-active-state {
+		pins = "gpio2", "gpio3", "gpio4", "gpio5";
+		function = "normal";
+
+		bias-pull-up;
+		power-source = <PM8941_GPIO_S3>;
+	};
+};
+
+&pm8941_lpg {
+	status = "okay";
+
+	qcom,power-source = <1>;
+
+	rgb-led {
+		color = <LED_COLOR_ID_RGB>;
+		function = LED_FUNCTION_STATUS;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		led@5 {
+			reg = <5>;
+			color = <LED_COLOR_ID_BLUE>;
+		};
+
+		led@6 {
+			reg = <6>;
+			color = <LED_COLOR_ID_GREEN>;
+		};
+
+		led@7 {
+			reg = <7>;
+			color = <LED_COLOR_ID_RED>;
+		};
+	};
+};
+
+&pm8941_wled {
+	status = "okay";
+
+	qcom,cs-out;
+	qcom,current-limit = <20>;
+	qcom,current-boost-limit = <805>;
+	qcom,switching-freq = <1600>;
+	qcom,ovp = <29>;
+	qcom,num-strings = <2>;
+};
+
+&rpm_requests {
+	pm8841-regulators {
+		compatible = "qcom,rpm-pm8841-regulators";
+
+		pm8841_s1: s1 {
+			regulator-min-microvolt = <675000>;
+			regulator-max-microvolt = <1050000>;
+		};
+
+		pm8841_s2: s2 {
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1050000>;
+		};
+
+		pm8841_s3: s3 {
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1050000>;
+		};
+
+		pm8841_s4: s4 {
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1050000>;
+		};
+	};
+
+	pm8941-regulators {
+		compatible = "qcom,rpm-pm8941-regulators";
+
+		vdd_l1_l3-supply = <&pm8941_s1>;
+		vdd_l2_lvs1_2_3-supply = <&pm8941_s3>;
+		vdd_l4_l11-supply = <&pm8941_s1>;
+		vdd_l5_l7-supply = <&pm8941_s2>;
+		vdd_l6_l12_l14_l15-supply = <&pm8941_s2>;
+		vdd_l9_l10_l17_l22-supply = <&vreg_boost>;
+		vdd_l13_l20_l23_l24-supply = <&vreg_boost>;
+		vdd_l21-supply = <&vreg_boost>;
+
+		pm8941_s1: s1 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		pm8941_s2: s2 {
+			regulator-min-microvolt = <2150000>;
+			regulator-max-microvolt = <2150000>;
+			regulator-boot-on;
+		};
+
+		pm8941_s3: s3 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		pm8941_s4: s4 {
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+		};
+
+		pm8941_l1: l1 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		pm8941_l2: l2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8941_l3: l3 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8941_l4: l4 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+		};
+
+		pm8941_l5: l5 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8941_l6: l6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-boot-on;
+		};
+
+		pm8941_l7: l7 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-boot-on;
+		};
+
+		pm8941_l8: l8 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8941_l9: l9 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8941_l11: l11 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1350000>;
+		};
+
+		pm8941_l12: l12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		pm8941_l13: l13 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-boot-on;
+		};
+
+		pm8941_l14: l14 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8941_l15: l15 {
+			regulator-min-microvolt = <2050000>;
+			regulator-max-microvolt = <2050000>;
+		};
+
+		pm8941_l16: l16 {
+			regulator-min-microvolt = <2700000>;
+			regulator-max-microvolt = <2700000>;
+		};
+
+		pm8941_l17: l17 {
+			regulator-min-microvolt = <2700000>;
+			regulator-max-microvolt = <2700000>;
+		};
+
+		pm8941_l18: l18 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+		};
+
+		pm8941_l19: l19 {
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+		};
+
+		pm8941_l20: l20 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-system-load = <200000>;
+			regulator-allow-set-load;
+			regulator-boot-on;
+		};
+
+		pm8941_l21: l21 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-boot-on;
+		};
+
+		pm8941_l22: l22 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+		};
+
+		pm8941_l23: l23 {
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+		};
+
+		pm8941_l24: l24 {
+			regulator-min-microvolt = <3075000>;
+			regulator-max-microvolt = <3075000>;
+			regulator-boot-on;
+		};
+
+		pm8941_lvs3: lvs3 {};
+	};
+};
+
+&sdhc_1 {
+	status = "okay";
+
+	vmmc-supply = <&pm8941_l20>;
+	vqmmc-supply = <&pm8941_s3>;
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sdc1_on>;
+	pinctrl-1 = <&sdc1_off>;
+};
+
+&sdhc_2 {
+	status = "okay";
+
+	vmmc-supply = <&pm8941_l21>;
+	vqmmc-supply = <&pm8941_l13>;
+
+	cd-gpios = <&tlmm 62 GPIO_ACTIVE_LOW>;
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sdc2_on>;
+	pinctrl-1 = <&sdc2_off>;
+};
+
+&smbb {
+	qcom,fast-charge-safe-current = <1500000>;
+	qcom,fast-charge-current-limit = <1500000>;
+	qcom,dc-current-limit = <1800000>;
+	qcom,fast-charge-safe-voltage = <4400000>;
+	qcom,fast-charge-high-threshold-voltage = <4350000>;
+	qcom,fast-charge-low-threshold-voltage = <3400000>;
+	qcom,auto-recharge-threshold-voltage = <4200000>;
+	qcom,minimum-input-voltage = <4300000>;
+};
+
+&tlmm {
+	ts_int_pin: touch-int {
+		pins = "gpio61";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+		input-enable;
+	};
+
+	sdc1_on: sdc1-on {
+		clk {
+			pins = "sdc1_clk";
+			drive-strength = <16>;
+			bias-disable;
+		};
+
+		cmd-data {
+			pins = "sdc1_cmd", "sdc1_data";
+			drive-strength = <10>;
+			bias-pull-up;
+		};
+	};
+
+	sdc2_on: sdc-on {
+		clk {
+			pins = "sdc2_clk";
+			drive-strength = <10>;
+			bias-disable;
+		};
+
+		cmd-data {
+			pins = "sdc2_cmd", "sdc2_data";
+			drive-strength = <6>;
+			bias-pull-up;
+		};
+
+		cd {
+			pins = "gpio62";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-disable;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/qcom-msm8974.dtsi b/arch/arm/boot/dts/qcom-msm8974.dtsi
index 412d94736c35..7a9be0acf3f5 100644
--- a/arch/arm/boot/dts/qcom-msm8974.dtsi
+++ b/arch/arm/boot/dts/qcom-msm8974.dtsi
@@ -12,61 +12,19 @@
 / {
 	#address-cells = <1>;
 	#size-cells = <1>;
-	model = "Qualcomm MSM8974";
-	compatible = "qcom,msm8974";
 	interrupt-parent = <&intc>;
 
-	reserved-memory {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-
-		mpss_region: mpss@8000000 {
-			reg = <0x08000000 0x5100000>;
-			no-map;
-		};
-
-		mba_region: mba@d100000 {
-			reg = <0x0d100000 0x100000>;
-			no-map;
-		};
-
-		wcnss_region: wcnss@d200000 {
-			reg = <0x0d200000 0xa00000>;
-			no-map;
-		};
-
-		adsp_region: adsp@dc00000 {
-			reg = <0x0dc00000 0x1900000>;
-			no-map;
-		};
-
-		venus@f500000 {
-			reg = <0x0f500000 0x500000>;
-			no-map;
-		};
-
-		smem_region: smem@fa00000 {
-			reg = <0xfa00000 0x200000>;
-			no-map;
-		};
-
-		tz@fc00000 {
-			reg = <0x0fc00000 0x160000>;
-			no-map;
-		};
-
-		rfsa@fd60000 {
-			reg = <0x0fd60000 0x20000>;
-			no-map;
+	clocks {
+		xo_board: xo_board {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <19200000>;
 		};
 
-		rmtfs@fd80000 {
-			compatible = "qcom,rmtfs-mem";
-			reg = <0x0fd80000 0x180000>;
-			no-map;
-
-			qcom,client-id = <1>;
+		sleep_clk: sleep_clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <32768>;
 		};
 	};
 
@@ -136,238 +94,75 @@
 		};
 	};
 
+	firmware {
+		scm {
+			compatible = "qcom,scm-msm8974", "qcom,scm";
+			clocks = <&gcc GCC_CE1_CLK>, <&gcc GCC_CE1_AXI_CLK>, <&gcc GCC_CE1_AHB_CLK>;
+			clock-names = "core", "bus", "iface";
+		};
+	};
+
 	memory {
 		device_type = "memory";
 		reg = <0x0 0x0>;
 	};
 
-	thermal-zones {
-		cpu0-thermal {
-			polling-delay-passive = <250>;
-			polling-delay = <1000>;
-
-			thermal-sensors = <&tsens 5>;
-
-			trips {
-				cpu_alert0: trip0 {
-					temperature = <75000>;
-					hysteresis = <2000>;
-					type = "passive";
-				};
-				cpu_crit0: trip1 {
-					temperature = <110000>;
-					hysteresis = <2000>;
-					type = "critical";
-				};
-			};
-		};
-
-		cpu1-thermal {
-			polling-delay-passive = <250>;
-			polling-delay = <1000>;
-
-			thermal-sensors = <&tsens 6>;
-
-			trips {
-				cpu_alert1: trip0 {
-					temperature = <75000>;
-					hysteresis = <2000>;
-					type = "passive";
-				};
-				cpu_crit1: trip1 {
-					temperature = <110000>;
-					hysteresis = <2000>;
-					type = "critical";
-				};
-			};
-		};
-
-		cpu2-thermal {
-			polling-delay-passive = <250>;
-			polling-delay = <1000>;
-
-			thermal-sensors = <&tsens 7>;
-
-			trips {
-				cpu_alert2: trip0 {
-					temperature = <75000>;
-					hysteresis = <2000>;
-					type = "passive";
-				};
-				cpu_crit2: trip1 {
-					temperature = <110000>;
-					hysteresis = <2000>;
-					type = "critical";
-				};
-			};
-		};
-
-		cpu3-thermal {
-			polling-delay-passive = <250>;
-			polling-delay = <1000>;
-
-			thermal-sensors = <&tsens 8>;
-
-			trips {
-				cpu_alert3: trip0 {
-					temperature = <75000>;
-					hysteresis = <2000>;
-					type = "passive";
-				};
-				cpu_crit3: trip1 {
-					temperature = <110000>;
-					hysteresis = <2000>;
-					type = "critical";
-				};
-			};
-		};
-
-		q6-dsp-thermal {
-			polling-delay-passive = <250>;
-			polling-delay = <1000>;
+	pmu {
+		compatible = "qcom,krait-pmu";
+		interrupts = <GIC_PPI 7 0xf04>;
+	};
 
-			thermal-sensors = <&tsens 1>;
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
 
-			trips {
-				q6_dsp_alert0: trip-point0 {
-					temperature = <90000>;
-					hysteresis = <2000>;
-					type = "hot";
-				};
-			};
+		mpss_region: mpss@8000000 {
+			reg = <0x08000000 0x5100000>;
+			no-map;
 		};
 
-		modemtx-thermal {
-			polling-delay-passive = <250>;
-			polling-delay = <1000>;
-
-			thermal-sensors = <&tsens 2>;
-
-			trips {
-				modemtx_alert0: trip-point0 {
-					temperature = <90000>;
-					hysteresis = <2000>;
-					type = "hot";
-				};
-			};
+		mba_region: mba@d100000 {
+			reg = <0x0d100000 0x100000>;
+			no-map;
 		};
 
-		video-thermal {
-			polling-delay-passive = <250>;
-			polling-delay = <1000>;
-
-			thermal-sensors = <&tsens 3>;
-
-			trips {
-				video_alert0: trip-point0 {
-					temperature = <95000>;
-					hysteresis = <2000>;
-					type = "hot";
-				};
-			};
+		wcnss_region: wcnss@d200000 {
+			reg = <0x0d200000 0xa00000>;
+			no-map;
 		};
 
-		wlan-thermal {
-			polling-delay-passive = <250>;
-			polling-delay = <1000>;
-
-			thermal-sensors = <&tsens 4>;
-
-			trips {
-				wlan_alert0: trip-point0 {
-					temperature = <105000>;
-					hysteresis = <2000>;
-					type = "hot";
-				};
-			};
+		adsp_region: adsp@dc00000 {
+			reg = <0x0dc00000 0x1900000>;
+			no-map;
 		};
 
-		gpu-top-thermal {
-			polling-delay-passive = <250>;
-			polling-delay = <1000>;
-
-			thermal-sensors = <&tsens 9>;
-
-			trips {
-				gpu1_alert0: trip-point0 {
-					temperature = <90000>;
-					hysteresis = <2000>;
-					type = "hot";
-				};
-			};
+		venus_region: memory@f500000 {
+			reg = <0x0f500000 0x500000>;
+			no-map;
 		};
 
-		gpu-bottom-thermal {
-			polling-delay-passive = <250>;
-			polling-delay = <1000>;
-
-			thermal-sensors = <&tsens 10>;
-
-			trips {
-				gpu2_alert0: trip-point0 {
-					temperature = <90000>;
-					hysteresis = <2000>;
-					type = "hot";
-				};
-			};
+		smem_region: smem@fa00000 {
+			reg = <0xfa00000 0x200000>;
+			no-map;
 		};
-	};
-
-	cpu-pmu {
-		compatible = "qcom,krait-pmu";
-		interrupts = <GIC_PPI 7 0xf04>;
-	};
 
-	clocks {
-		xo_board: xo_board {
-			compatible = "fixed-clock";
-			#clock-cells = <0>;
-			clock-frequency = <19200000>;
+		tz_region: memory@fc00000 {
+			reg = <0x0fc00000 0x160000>;
+			no-map;
 		};
 
-		sleep_clk: sleep_clk {
-			compatible = "fixed-clock";
-			#clock-cells = <0>;
-			clock-frequency = <32768>;
+		rfsa_mem: memory@fd60000 {
+			reg = <0x0fd60000 0x20000>;
+			no-map;
 		};
-	};
 
-	timer {
-		compatible = "arm,armv7-timer";
-		interrupts = <GIC_PPI 2 0xf08>,
-			     <GIC_PPI 3 0xf08>,
-			     <GIC_PPI 4 0xf08>,
-			     <GIC_PPI 1 0xf08>;
-		clock-frequency = <19200000>;
-	};
-
-	adsp-pil {
-		compatible = "qcom,msm8974-adsp-pil";
-
-		interrupts-extended = <&intc GIC_SPI 162 IRQ_TYPE_EDGE_RISING>,
-				      <&adsp_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
-				      <&adsp_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
-				      <&adsp_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
-				      <&adsp_smp2p_in 3 IRQ_TYPE_EDGE_RISING>;
-		interrupt-names = "wdog", "fatal", "ready", "handover", "stop-ack";
-
-		cx-supply = <&pm8841_s2>;
-
-		clocks = <&xo_board>;
-		clock-names = "xo";
-
-		memory-region = <&adsp_region>;
-
-		qcom,smem-states = <&adsp_smp2p_out 0>;
-		qcom,smem-state-names = "stop";
-
-		smd-edge {
-			interrupts = <GIC_SPI 156 IRQ_TYPE_EDGE_RISING>;
-
-			qcom,ipc = <&apcs 8 8>;
-			qcom,smd-edge = <1>;
+		rmtfs@fd80000 {
+			compatible = "qcom,rmtfs-mem";
+			reg = <0x0fd80000 0x180000>;
+			no-map;
 
-			label = "lpass";
+			qcom,client-id = <1>;
 		};
 	};
 
@@ -497,11 +292,23 @@
 		};
 	};
 
-	firmware {
-		scm {
-			compatible = "qcom,scm";
-			clocks = <&gcc GCC_CE1_CLK>, <&gcc GCC_CE1_AXI_CLK>, <&gcc GCC_CE1_AHB_CLK>;
-			clock-names = "core", "bus", "iface";
+	smd {
+		compatible = "qcom,smd";
+
+		rpm {
+			interrupts = <GIC_SPI 168 IRQ_TYPE_EDGE_RISING>;
+			qcom,ipc = <&apcs 8 0>;
+			qcom,smd-edge = <15>;
+
+			rpm_requests: rpm_requests {
+				compatible = "qcom,rpm-msm8974";
+				qcom,smd-channels = "rpm_requests";
+
+				rpmcc: clock-controller {
+					compatible = "qcom,rpmcc-msm8974", "qcom,rpmcc";
+					#clock-cells = <1>;
+				};
+			};
 		};
 	};
 
@@ -524,31 +331,6 @@
 			reg = <0xf9011000 0x1000>;
 		};
 
-		qfprom: qfprom@fc4bc000 {
-			#address-cells = <1>;
-			#size-cells = <1>;
-			compatible = "qcom,qfprom";
-			reg = <0xfc4bc000 0x1000>;
-			tsens_calib: calib@d0 {
-				reg = <0xd0 0x18>;
-			};
-			tsens_backup: backup@440 {
-				reg = <0x440 0x10>;
-			};
-		};
-
-		tsens: thermal-sensor@fc4a9000 {
-			compatible = "qcom,msm8974-tsens";
-			reg = <0xfc4a9000 0x1000>, /* TM */
-			      <0xfc4a8000 0x1000>; /* SROT */
-			nvmem-cells = <&tsens_calib>, <&tsens_backup>;
-			nvmem-cell-names = "calib", "calib_backup";
-			#qcom,sensors = <11>;
-			interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "uplow";
-			#thermal-sensor-cells = <1>;
-		};
-
 		timer@f9020000 {
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -654,47 +436,59 @@
 			reg = <0xf90b8000 0x1000>, <0xf9008000 0x1000>;
 		};
 
-		restart@fc4ab000 {
-			compatible = "qcom,pshold";
-			reg = <0xfc4ab000 0x4>;
-		};
+		sdhc_1: mmc@f9824900 {
+			compatible = "qcom,msm8974-sdhci", "qcom,sdhci-msm-v4";
+			reg = <0xf9824900 0x11c>, <0xf9824000 0x800>;
+			reg-names = "hc", "core";
+			interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hc_irq", "pwr_irq";
+			clocks = <&gcc GCC_SDCC1_AHB_CLK>,
+				 <&gcc GCC_SDCC1_APPS_CLK>,
+				 <&xo_board>;
+			clock-names = "iface", "core", "xo";
+			bus-width = <8>;
+			non-removable;
 
-		gcc: clock-controller@fc400000 {
-			compatible = "qcom,gcc-msm8974";
-			#clock-cells = <1>;
-			#reset-cells = <1>;
-			#power-domain-cells = <1>;
-			reg = <0xfc400000 0x4000>;
+			status = "disabled";
 		};
 
-		tcsr: syscon@fd4a0000 {
-			compatible = "syscon";
-			reg = <0xfd4a0000 0x10000>;
-		};
+		sdhc_3: mmc@f9864900 {
+			compatible = "qcom,msm8974-sdhci", "qcom,sdhci-msm-v4";
+			reg = <0xf9864900 0x11c>, <0xf9864000 0x800>;
+			reg-names = "hc", "core";
+			interrupts = <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 224 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hc_irq", "pwr_irq";
+			clocks = <&gcc GCC_SDCC3_AHB_CLK>,
+				 <&gcc GCC_SDCC3_APPS_CLK>,
+				 <&xo_board>;
+			clock-names = "iface", "core", "xo";
+			bus-width = <4>;
 
-		tcsr_mutex_block: syscon@fd484000 {
-			compatible = "syscon";
-			reg = <0xfd484000 0x2000>;
-		};
+			#address-cells = <1>;
+			#size-cells = <0>;
 
-		mmcc: clock-controller@fd8c0000 {
-			compatible = "qcom,mmcc-msm8974";
-			#clock-cells = <1>;
-			#reset-cells = <1>;
-			#power-domain-cells = <1>;
-			reg = <0xfd8c0000 0x6000>;
+			status = "disabled";
 		};
 
-		tcsr_mutex: tcsr-mutex {
-			compatible = "qcom,tcsr-mutex";
-			syscon = <&tcsr_mutex_block 0 0x80>;
+		sdhc_2: mmc@f98a4900 {
+			compatible = "qcom,msm8974-sdhci", "qcom,sdhci-msm-v4";
+			reg = <0xf98a4900 0x11c>, <0xf98a4000 0x800>;
+			reg-names = "hc", "core";
+			interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 221 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hc_irq", "pwr_irq";
+			clocks = <&gcc GCC_SDCC2_AHB_CLK>,
+				 <&gcc GCC_SDCC2_APPS_CLK>,
+				 <&xo_board>;
+			clock-names = "iface", "core", "xo";
+			bus-width = <4>;
 
-			#hwlock-cells = <1>;
-		};
+			#address-cells = <1>;
+			#size-cells = <0>;
 
-		rpm_msg_ram: memory@fc428000 {
-			compatible = "qcom,rpm-msg-ram";
-			reg = <0xfc428000 0x4000>;
+			status = "disabled";
 		};
 
 		blsp1_uart1: serial@f991d000 {
@@ -712,19 +506,90 @@
 			interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&gcc GCC_BLSP1_UART2_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
 			clock-names = "core", "iface";
+			pinctrl-names = "default";
+			pinctrl-0 = <&blsp1_uart2_default>;
+			status = "disabled";
+		};
+
+		blsp1_i2c1: i2c@f9923000 {
+			status = "disabled";
+			compatible = "qcom,i2c-qup-v2.1.1";
+			reg = <0xf9923000 0x1000>;
+			interrupts = <0 95 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_QUP1_I2C_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&blsp1_i2c1_default>;
+			pinctrl-1 = <&blsp1_i2c1_sleep>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		blsp1_i2c2: i2c@f9924000 {
+			status = "disabled";
+			compatible = "qcom,i2c-qup-v2.1.1";
+			reg = <0xf9924000 0x1000>;
+			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&blsp1_i2c2_default>;
+			pinctrl-1 = <&blsp1_i2c2_sleep>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		blsp1_i2c3: i2c@f9925000 {
+			status = "disabled";
+			compatible = "qcom,i2c-qup-v2.1.1";
+			reg = <0xf9925000 0x1000>;
+			interrupts = <0 97 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&blsp1_i2c3_default>;
+			pinctrl-1 = <&blsp1_i2c3_sleep>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		blsp1_i2c6: i2c@f9928000 {
 			status = "disabled";
+			compatible = "qcom,i2c-qup-v2.1.1";
+			reg = <0xf9928000 0x1000>;
+			interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_QUP6_I2C_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&blsp1_i2c6_default>;
+			pinctrl-1 = <&blsp1_i2c6_sleep>;
+			#address-cells = <1>;
+			#size-cells = <0>;
 		};
 
-		blsp2_uart7: serial@f995d000 {
+		blsp2_dma: dma-controller@f9944000 {
+			compatible = "qcom,bam-v1.4.0";
+			reg = <0xf9944000 0x19000>;
+			interrupts = <GIC_SPI 239 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP2_AHB_CLK>;
+			clock-names = "bam_clk";
+			#dma-cells = <1>;
+			qcom,ee = <0>;
+		};
+
+		blsp2_uart1: serial@f995d000 {
 			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
 			reg = <0xf995d000 0x1000>;
-			interrupts = <GIC_SPI 113 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&gcc GCC_BLSP2_UART1_APPS_CLK>, <&gcc GCC_BLSP2_AHB_CLK>;
 			clock-names = "core", "iface";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&blsp2_uart1_default>;
+			pinctrl-1 = <&blsp2_uart1_sleep>;
 			status = "disabled";
 		};
 
-		blsp2_uart8: serial@f995e000 {
+		blsp2_uart2: serial@f995e000 {
 			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
 			reg = <0xf995e000 0x1000>;
 			interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>;
@@ -733,55 +598,59 @@
 			status = "disabled";
 		};
 
-		blsp2_uart10: serial@f9960000 {
+		blsp2_uart4: serial@f9960000 {
 			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
 			reg = <0xf9960000 0x1000>;
 			interrupts = <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&gcc GCC_BLSP2_UART4_APPS_CLK>, <&gcc GCC_BLSP2_AHB_CLK>;
 			clock-names = "core", "iface";
+			pinctrl-names = "default";
+			pinctrl-0 = <&blsp2_uart4_default>;
 			status = "disabled";
 		};
 
-		sdhci@f9824900 {
-			compatible = "qcom,msm8974-sdhci", "qcom,sdhci-msm-v4";
-			reg = <0xf9824900 0x11c>, <0xf9824000 0x800>;
-			reg-names = "hc_mem", "core_mem";
-			interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "hc_irq", "pwr_irq";
-			clocks = <&gcc GCC_SDCC1_APPS_CLK>,
-				 <&gcc GCC_SDCC1_AHB_CLK>,
-				 <&xo_board>;
-			clock-names = "core", "iface", "xo";
+		blsp2_i2c2: i2c@f9964000 {
 			status = "disabled";
+			compatible = "qcom,i2c-qup-v2.1.1";
+			reg = <0xf9964000 0x1000>;
+			interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP2_QUP2_I2C_APPS_CLK>, <&gcc GCC_BLSP2_AHB_CLK>;
+			clock-names = "core", "iface";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&blsp2_i2c2_default>;
+			pinctrl-1 = <&blsp2_i2c2_sleep>;
+			#address-cells = <1>;
+			#size-cells = <0>;
 		};
 
-		sdhci@f9864900 {
-			compatible = "qcom,msm8974-sdhci", "qcom,sdhci-msm-v4";
-			reg = <0xf9864900 0x11c>, <0xf9864000 0x800>;
-			reg-names = "hc_mem", "core_mem";
-			interrupts = <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 224 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "hc_irq", "pwr_irq";
-			clocks = <&gcc GCC_SDCC3_APPS_CLK>,
-				 <&gcc GCC_SDCC3_AHB_CLK>,
-				 <&xo_board>;
-			clock-names = "core", "iface", "xo";
+		blsp2_i2c5: i2c@f9967000 {
 			status = "disabled";
+			compatible = "qcom,i2c-qup-v2.1.1";
+			reg = <0xf9967000 0x1000>;
+			interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP2_QUP5_I2C_APPS_CLK>, <&gcc GCC_BLSP2_AHB_CLK>;
+			clock-names = "core", "iface";
+			dmas = <&blsp2_dma 20>, <&blsp2_dma 21>;
+			dma-names = "tx", "rx";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&blsp2_i2c5_default>;
+			pinctrl-1 = <&blsp2_i2c5_sleep>;
+			#address-cells = <1>;
+			#size-cells = <0>;
 		};
 
-		sdhci@f98a4900 {
-			compatible = "qcom,msm8974-sdhci", "qcom,sdhci-msm-v4";
-			reg = <0xf98a4900 0x11c>, <0xf98a4000 0x800>;
-			reg-names = "hc_mem", "core_mem";
-			interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 221 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "hc_irq", "pwr_irq";
-			clocks = <&gcc GCC_SDCC2_APPS_CLK>,
-				 <&gcc GCC_SDCC2_AHB_CLK>,
-				 <&xo_board>;
-			clock-names = "core", "iface", "xo";
+		blsp2_i2c6: i2c@f9968000 {
 			status = "disabled";
+			compatible = "qcom,i2c-qup-v2.1.1";
+			reg = <0xf9968000 0x1000>;
+			interrupts = <0 106 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP2_QUP6_I2C_APPS_CLK>, <&gcc GCC_BLSP2_AHB_CLK>;
+			clock-names = "core", "iface";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&blsp2_i2c6_default>;
+			pinctrl-1 = <&blsp2_i2c6_sleep>;
+			#address-cells = <1>;
+			#size-cells = <0>;
 		};
 
 		otg: usb@f9a55000 {
@@ -835,55 +704,6 @@
 			clock-names = "core";
 		};
 
-		remoteproc@fc880000 {
-			compatible = "qcom,msm8974-mss-pil";
-			reg = <0xfc880000 0x100>, <0xfc820000 0x020>;
-			reg-names = "qdsp6", "rmb";
-
-			interrupts-extended = <&intc GIC_SPI 24 IRQ_TYPE_EDGE_RISING>,
-					      <&modem_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
-					      <&modem_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
-					      <&modem_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
-					      <&modem_smp2p_in 3 IRQ_TYPE_EDGE_RISING>;
-			interrupt-names = "wdog", "fatal", "ready", "handover", "stop-ack";
-
-			clocks = <&gcc GCC_MSS_Q6_BIMC_AXI_CLK>,
-				 <&gcc GCC_MSS_CFG_AHB_CLK>,
-				 <&gcc GCC_BOOT_ROM_AHB_CLK>,
-				 <&xo_board>;
-			clock-names = "iface", "bus", "mem", "xo";
-
-			resets = <&gcc GCC_MSS_RESTART>;
-			reset-names = "mss_restart";
-
-			cx-supply = <&pm8841_s2>;
-			mss-supply = <&pm8841_s3>;
-			mx-supply = <&pm8841_s1>;
-			pll-supply = <&pm8941_l12>;
-
-			qcom,halt-regs = <&tcsr_mutex_block 0x1180 0x1200 0x1280>;
-
-			qcom,smem-states = <&modem_smp2p_out 0>;
-			qcom,smem-state-names = "stop";
-
-			mba {
-				memory-region = <&mba_region>;
-			};
-
-			mpss {
-				memory-region = <&mpss_region>;
-			};
-
-			smd-edge {
-				interrupts = <GIC_SPI 25 IRQ_TYPE_EDGE_RISING>;
-
-				qcom,ipc = <&apcs 8 12>;
-				qcom,smd-edge = <0>;
-
-				label = "modem";
-			};
-		};
-
 		pronto: remoteproc@fb21b000 {
 			compatible = "qcom,pronto-v2-pil", "qcom,pronto";
 			reg = <0xfb204000 0x2000>, <0xfb202000 0x1000>, <0xfb21b000 0x3000>;
@@ -898,8 +718,6 @@
 					      <&wcnss_smp2p_in 3 IRQ_TYPE_EDGE_RISING>;
 			interrupt-names = "wdog", "fatal", "ready", "handover", "stop-ack";
 
-			vddpx-supply = <&pm8941_s3>;
-
 			qcom,smem-states = <&wcnss_smp2p_out 0>;
 			qcom,smem-state-names = "stop";
 
@@ -910,11 +728,6 @@
 
 				clocks = <&rpmcc RPM_SMD_CXO_A2>;
 				clock-names = "xo";
-
-				vddxo-supply = <&pm8941_l6>;
-				vddrfa-supply = <&pm8941_l11>;
-				vddpa-supply = <&pm8941_l19>;
-				vdddig-supply = <&pm8941_s3>;
 			};
 
 			smd-edge {
@@ -942,139 +755,37 @@
 						interrupt-names = "tx", "rx";
 
 						qcom,smem-states = <&apps_smsm 10>, <&apps_smsm 9>;
-						qcom,smem-state-names = "tx-enable", "tx-rings-empty";
+						qcom,smem-state-names = "tx-enable",
+									"tx-rings-empty";
 					};
 				};
 			};
 		};
 
-		msmgpio: pinctrl@fd510000 {
-			compatible = "qcom,msm8974-pinctrl";
-			reg = <0xfd510000 0x4000>;
-			gpio-controller;
-			gpio-ranges = <&msmgpio 0 0 146>;
-			#gpio-cells = <2>;
-			interrupt-controller;
-			#interrupt-cells = <2>;
-			interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
-		};
-
-		i2c@f9923000 {
-			status = "disabled";
-			compatible = "qcom,i2c-qup-v2.1.1";
-			reg = <0xf9923000 0x1000>;
-			interrupts = <0 95 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc GCC_BLSP1_QUP1_I2C_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
-			clock-names = "core", "iface";
-			#address-cells = <1>;
-			#size-cells = <0>;
-		};
-
-		i2c@f9924000 {
-			status = "disabled";
-			compatible = "qcom,i2c-qup-v2.1.1";
-			reg = <0xf9924000 0x1000>;
-			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
-			clock-names = "core", "iface";
-			#address-cells = <1>;
-			#size-cells = <0>;
-		};
-
-		blsp_i2c3: i2c@f9925000 {
-			status = "disabled";
-			compatible = "qcom,i2c-qup-v2.1.1";
-			reg = <0xf9925000 0x1000>;
-			interrupts = <0 97 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
-			clock-names = "core", "iface";
-			#address-cells = <1>;
-			#size-cells = <0>;
-		};
-
-		blsp_i2c6: i2c@f9928000 {
-			status = "disabled";
-			compatible = "qcom,i2c-qup-v2.1.1";
-			reg = <0xf9928000 0x1000>;
-			interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc GCC_BLSP1_QUP6_I2C_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
-			clock-names = "core", "iface";
-			#address-cells = <1>;
-			#size-cells = <0>;
-		};
-
-		blsp_i2c8: i2c@f9964000 {
-			status = "disabled";
-			compatible = "qcom,i2c-qup-v2.1.1";
-			reg = <0xf9964000 0x1000>;
-			interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc GCC_BLSP2_QUP2_I2C_APPS_CLK>, <&gcc GCC_BLSP2_AHB_CLK>;
-			clock-names = "core", "iface";
-			#address-cells = <1>;
-			#size-cells = <0>;
-		};
-
-		blsp_i2c11: i2c@f9967000 {
-			status = "disabled";
-			compatible = "qcom,i2c-qup-v2.1.1";
-			reg = <0xf9967000 0x1000>;
-			interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc GCC_BLSP2_QUP5_I2C_APPS_CLK>, <&gcc GCC_BLSP2_AHB_CLK>;
-			clock-names = "core", "iface";
-			#address-cells = <1>;
-			#size-cells = <0>;
-			dmas = <&blsp2_dma 20>, <&blsp2_dma 21>;
-			dma-names = "tx", "rx";
-		};
-
-		blsp_i2c12: i2c@f9968000 {
-			status = "disabled";
-			compatible = "qcom,i2c-qup-v2.1.1";
-			reg = <0xf9968000 0x1000>;
-			interrupts = <0 106 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc GCC_BLSP2_QUP6_I2C_APPS_CLK>, <&gcc GCC_BLSP2_AHB_CLK>;
-			clock-names = "core", "iface";
-			#address-cells = <1>;
-			#size-cells = <0>;
-		};
-
-		spmi_bus: spmi@fc4cf000 {
-			compatible = "qcom,spmi-pmic-arb";
-			reg-names = "core", "intr", "cnfg";
-			reg = <0xfc4cf000 0x1000>,
-			      <0xfc4cb000 0x1000>,
-			      <0xfc4ca000 0x1000>;
-			interrupt-names = "periph_irq";
-			interrupts = <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>;
-			qcom,ee = <0>;
-			qcom,channel = <0>;
-			#address-cells = <2>;
-			#size-cells = <0>;
-			interrupt-controller;
-			#interrupt-cells = <4>;
-		};
-
-		blsp2_dma: dma-controller@f9944000 {
-			compatible = "qcom,bam-v1.4.0";
-			reg = <0xf9944000 0x19000>;
-			interrupts = <GIC_SPI 239 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc GCC_BLSP2_AHB_CLK>;
-			clock-names = "bam_clk";
-			#dma-cells = <1>;
-			qcom,ee = <0>;
+		sram@fc190000 {
+			compatible = "qcom,msm8974-rpm-stats";
+			reg = <0xfc190000 0x10000>;
 		};
 
-		etr@fc322000 {
+		etf@fc307000 {
 			compatible = "arm,coresight-tmc", "arm,primecell";
-			reg = <0xfc322000 0x1000>;
+			reg = <0xfc307000 0x1000>;
 
 			clocks = <&rpmcc RPM_SMD_QDSS_CLK>, <&rpmcc RPM_SMD_QDSS_A_CLK>;
 			clock-names = "apb_pclk", "atclk";
 
+			out-ports {
+				port {
+					etf_out: endpoint {
+						remote-endpoint = <&replicator_in>;
+					};
+				};
+			};
+
 			in-ports {
 				port {
-					etr_in: endpoint {
-						remote-endpoint = <&replicator_out0>;
+					etf_in: endpoint {
+						remote-endpoint = <&merger_out>;
 					};
 				};
 			};
@@ -1096,59 +807,39 @@
 			};
 		};
 
-		replicator@fc31c000 {
-			compatible = "arm,coresight-dynamic-replicator", "arm,primecell";
-			reg = <0xfc31c000 0x1000>;
+		funnel@fc31a000 {
+			compatible = "arm,coresight-dynamic-funnel", "arm,primecell";
+			reg = <0xfc31a000 0x1000>;
 
 			clocks = <&rpmcc RPM_SMD_QDSS_CLK>, <&rpmcc RPM_SMD_QDSS_A_CLK>;
 			clock-names = "apb_pclk", "atclk";
 
-			out-ports {
+			in-ports {
 				#address-cells = <1>;
 				#size-cells = <0>;
 
-				port@0 {
-					reg = <0>;
-					replicator_out0: endpoint {
-						remote-endpoint = <&etr_in>;
-					};
-				};
-				port@1 {
-					reg = <1>;
-					replicator_out1: endpoint {
-						remote-endpoint = <&tpiu_in>;
-					};
-				};
-			};
-
-			in-ports {
-				port {
-					replicator_in: endpoint {
-						remote-endpoint = <&etf_out>;
+				/*
+				 * Not described input ports:
+				 * 0 - not-connected
+				 * 1 - connected trought funnel to Multimedia CPU
+				 * 2 - connected to Wireless CPU
+				 * 3 - not-connected
+				 * 4 - not-connected
+				 * 6 - not-connected
+				 * 7 - connected to STM
+				 */
+				port@5 {
+					reg = <5>;
+					funnel1_in5: endpoint {
+						remote-endpoint = <&kpss_out>;
 					};
 				};
 			};
-		};
-
-		etf@fc307000 {
-			compatible = "arm,coresight-tmc", "arm,primecell";
-			reg = <0xfc307000 0x1000>;
-
-			clocks = <&rpmcc RPM_SMD_QDSS_CLK>, <&rpmcc RPM_SMD_QDSS_A_CLK>;
-			clock-names = "apb_pclk", "atclk";
 
 			out-ports {
 				port {
-					etf_out: endpoint {
-						remote-endpoint = <&replicator_in>;
-					};
-				};
-			};
-
-			in-ports {
-				port {
-					etf_in: endpoint {
-						remote-endpoint = <&merger_out>;
+					funnel1_out: endpoint {
+						remote-endpoint = <&merger_in1>;
 					};
 				};
 			};
@@ -1188,85 +879,51 @@
 			};
 		};
 
-		funnel@fc31a000 {
-			compatible = "arm,coresight-dynamic-funnel", "arm,primecell";
-			reg = <0xfc31a000 0x1000>;
+		replicator@fc31c000 {
+			compatible = "arm,coresight-dynamic-replicator", "arm,primecell";
+			reg = <0xfc31c000 0x1000>;
 
 			clocks = <&rpmcc RPM_SMD_QDSS_CLK>, <&rpmcc RPM_SMD_QDSS_A_CLK>;
 			clock-names = "apb_pclk", "atclk";
 
-			in-ports {
+			out-ports {
 				#address-cells = <1>;
 				#size-cells = <0>;
 
-				/*
-				 * Not described input ports:
-				 * 0 - not-connected
-				 * 1 - connected trought funnel to Multimedia CPU
-				 * 2 - connected to Wireless CPU
-				 * 3 - not-connected
-				 * 4 - not-connected
-				 * 6 - not-connected
-				 * 7 - connected to STM
-				 */
-				port@5 {
-					reg = <5>;
-					funnel1_in5: endpoint {
-						remote-endpoint = <&kpss_out>;
+				port@0 {
+					reg = <0>;
+					replicator_out0: endpoint {
+						remote-endpoint = <&etr_in>;
+					};
+				};
+				port@1 {
+					reg = <1>;
+					replicator_out1: endpoint {
+						remote-endpoint = <&tpiu_in>;
 					};
 				};
 			};
 
-			out-ports {
+			in-ports {
 				port {
-					funnel1_out: endpoint {
-						remote-endpoint = <&merger_in1>;
+					replicator_in: endpoint {
+						remote-endpoint = <&etf_out>;
 					};
 				};
 			};
 		};
 
-		funnel@fc345000 { /* KPSS funnel only 4 inputs are used */
-			compatible = "arm,coresight-dynamic-funnel", "arm,primecell";
-			reg = <0xfc345000 0x1000>;
+		etr@fc322000 {
+			compatible = "arm,coresight-tmc", "arm,primecell";
+			reg = <0xfc322000 0x1000>;
 
 			clocks = <&rpmcc RPM_SMD_QDSS_CLK>, <&rpmcc RPM_SMD_QDSS_A_CLK>;
 			clock-names = "apb_pclk", "atclk";
 
 			in-ports {
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				port@0 {
-					reg = <0>;
-					kpss_in0: endpoint {
-						remote-endpoint = <&etm0_out>;
-					};
-				};
-				port@1 {
-					reg = <1>;
-					kpss_in1: endpoint {
-						remote-endpoint = <&etm1_out>;
-					};
-				};
-				port@2 {
-					reg = <2>;
-					kpss_in2: endpoint {
-						remote-endpoint = <&etm2_out>;
-					};
-				};
-				port@3 {
-					reg = <3>;
-					kpss_in3: endpoint {
-						remote-endpoint = <&etm3_out>;
-					};
-				};
-			};
-
-			out-ports {
 				port {
-					kpss_out: endpoint {
-						remote-endpoint = <&funnel1_in5>;
+					etr_in: endpoint {
+						remote-endpoint = <&replicator_out0>;
 					};
 				};
 			};
@@ -1344,25 +1001,66 @@
 			};
 		};
 
-		ocmem@fdd00000 {
-			compatible = "qcom,msm8974-ocmem";
-			reg = <0xfdd00000 0x2000>,
-			      <0xfec00000 0x180000>;
-			reg-names = "ctrl",
-			            "mem";
-			clocks = <&rpmcc RPM_SMD_OCMEMGX_CLK>,
-			         <&mmcc OCMEMCX_OCMEMNOC_CLK>;
-			clock-names = "core",
-			              "iface";
+		/* KPSS funnel, only 4 inputs are used */
+		funnel@fc345000 {
+			compatible = "arm,coresight-dynamic-funnel", "arm,primecell";
+			reg = <0xfc345000 0x1000>;
 
-			#address-cells = <1>;
-			#size-cells = <1>;
+			clocks = <&rpmcc RPM_SMD_QDSS_CLK>, <&rpmcc RPM_SMD_QDSS_A_CLK>;
+			clock-names = "apb_pclk", "atclk";
 
-			gmu_sram: gmu-sram@0 {
-				reg = <0x0 0x100000>;
+			in-ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+					kpss_in0: endpoint {
+						remote-endpoint = <&etm0_out>;
+					};
+				};
+				port@1 {
+					reg = <1>;
+					kpss_in1: endpoint {
+						remote-endpoint = <&etm1_out>;
+					};
+				};
+				port@2 {
+					reg = <2>;
+					kpss_in2: endpoint {
+						remote-endpoint = <&etm2_out>;
+					};
+				};
+				port@3 {
+					reg = <3>;
+					kpss_in3: endpoint {
+						remote-endpoint = <&etm3_out>;
+					};
+				};
+			};
+
+			out-ports {
+				port {
+					kpss_out: endpoint {
+						remote-endpoint = <&funnel1_in5>;
+					};
+				};
 			};
 		};
 
+		gcc: clock-controller@fc400000 {
+			compatible = "qcom,gcc-msm8974";
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+			#power-domain-cells = <1>;
+			reg = <0xfc400000 0x4000>;
+		};
+
+		rpm_msg_ram: memory@fc428000 {
+			compatible = "qcom,rpm-msg-ram";
+			reg = <0xfc428000 0x4000>;
+		};
+
 		bimc: interconnect@fc380000 {
 			reg = <0xfc380000 0x6a000>;
 			compatible = "qcom,msm8974-bimc";
@@ -1417,94 +1115,418 @@
 			         <&rpmcc RPM_SMD_CNOC_A_CLK>;
 		};
 
-		gpu: adreno@fdb00000 {
+		tsens: thermal-sensor@fc4a9000 {
+			compatible = "qcom,msm8974-tsens";
+			reg = <0xfc4a9000 0x1000>, /* TM */
+			      <0xfc4a8000 0x1000>; /* SROT */
+			nvmem-cells = <&tsens_calib>, <&tsens_backup>;
+			nvmem-cell-names = "calib", "calib_backup";
+			#qcom,sensors = <11>;
+			interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "uplow";
+			#thermal-sensor-cells = <1>;
+		};
+
+		restart@fc4ab000 {
+			compatible = "qcom,pshold";
+			reg = <0xfc4ab000 0x4>;
+		};
+
+		qfprom: qfprom@fc4bc000 {
+			compatible = "qcom,msm8974-qfprom", "qcom,qfprom";
+			reg = <0xfc4bc000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			tsens_calib: calib@d0 {
+				reg = <0xd0 0x18>;
+			};
+			tsens_backup: backup@440 {
+				reg = <0x440 0x10>;
+			};
+		};
+
+		spmi_bus: spmi@fc4cf000 {
+			compatible = "qcom,spmi-pmic-arb";
+			reg-names = "core", "intr", "cnfg";
+			reg = <0xfc4cf000 0x1000>,
+			      <0xfc4cb000 0x1000>,
+			      <0xfc4ca000 0x1000>;
+			interrupt-names = "periph_irq";
+			interrupts = <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>;
+			qcom,ee = <0>;
+			qcom,channel = <0>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+			interrupt-controller;
+			#interrupt-cells = <4>;
+		};
+
+		bam_dmux_dma: dma-controller@fc834000 {
+			compatible = "qcom,bam-v1.4.0";
+			reg = <0xfc834000 0x7000>;
+			interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
+			#dma-cells = <1>;
+			qcom,ee = <0>;
+
+			num-channels = <6>;
+			qcom,num-ees = <1>;
+			qcom,powered-remotely;
+		};
+
+		remoteproc_mss: remoteproc@fc880000 {
+			compatible = "qcom,msm8974-mss-pil";
+			reg = <0xfc880000 0x100>, <0xfc820000 0x020>;
+			reg-names = "qdsp6", "rmb";
+
+			interrupts-extended = <&intc GIC_SPI 24 IRQ_TYPE_EDGE_RISING>,
+					      <&modem_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
+					      <&modem_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
+					      <&modem_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
+					      <&modem_smp2p_in 3 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "wdog", "fatal", "ready", "handover", "stop-ack";
+
+			clocks = <&gcc GCC_MSS_Q6_BIMC_AXI_CLK>,
+				 <&gcc GCC_MSS_CFG_AHB_CLK>,
+				 <&gcc GCC_BOOT_ROM_AHB_CLK>,
+				 <&xo_board>;
+			clock-names = "iface", "bus", "mem", "xo";
+
+			resets = <&gcc GCC_MSS_RESTART>;
+			reset-names = "mss_restart";
+
+			qcom,halt-regs = <&tcsr_mutex_block 0x1180 0x1200 0x1280>;
+
+			qcom,smem-states = <&modem_smp2p_out 0>;
+			qcom,smem-state-names = "stop";
+
 			status = "disabled";
 
-			compatible = "qcom,adreno-330.1",
-				     "qcom,adreno";
-			reg = <0xfdb00000 0x10000>;
-			reg-names = "kgsl_3d0_reg_memory";
-			interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "kgsl_3d0_irq";
-			clock-names = "core",
-				      "iface",
-				      "mem_iface";
-			clocks = <&mmcc OXILI_GFX3D_CLK>,
-				 <&mmcc OXILICX_AHB_CLK>,
-				 <&mmcc OXILICX_AXI_CLK>;
-			sram = <&gmu_sram>;
-			power-domains = <&mmcc OXILICX_GDSC>;
-			operating-points-v2 = <&gpu_opp_table>;
+			mba {
+				memory-region = <&mba_region>;
+			};
 
-			interconnects = <&mmssnoc MNOC_MAS_GRAPHICS_3D &bimc BIMC_SLV_EBI_CH0>,
-					<&ocmemnoc OCMEM_VNOC_MAS_GFX3D &ocmemnoc OCMEM_SLV_OCMEM>;
-			interconnect-names = "gfx-mem",
-					     "ocmem";
+			mpss {
+				memory-region = <&mpss_region>;
+			};
 
-			// iommus = <&gpu_iommu 0>;
+			bam_dmux: bam-dmux {
+				compatible = "qcom,bam-dmux";
 
-			gpu_opp_table: opp_table {
-				compatible = "operating-points-v2";
+				interrupt-parent = <&modem_smsm>;
+				interrupts = <1 IRQ_TYPE_EDGE_BOTH>, <11 IRQ_TYPE_EDGE_BOTH>;
+				interrupt-names = "pc", "pc-ack";
 
-				opp-320000000 {
-					opp-hz = /bits/ 64 <320000000>;
+				qcom,smem-states = <&apps_smsm 1>, <&apps_smsm 11>;
+				qcom,smem-state-names = "pc", "pc-ack";
+
+				dmas = <&bam_dmux_dma 4>, <&bam_dmux_dma 5>;
+				dma-names = "tx", "rx";
+			};
+
+			smd-edge {
+				interrupts = <GIC_SPI 25 IRQ_TYPE_EDGE_RISING>;
+
+				qcom,ipc = <&apcs 8 12>;
+				qcom,smd-edge = <0>;
+
+				label = "modem";
+			};
+		};
+
+		tcsr_mutex_block: syscon@fd484000 {
+			compatible = "syscon";
+			reg = <0xfd484000 0x2000>;
+		};
+
+		tcsr: syscon@fd4a0000 {
+			compatible = "syscon";
+			reg = <0xfd4a0000 0x10000>;
+		};
+
+		tlmm: pinctrl@fd510000 {
+			compatible = "qcom,msm8974-pinctrl";
+			reg = <0xfd510000 0x4000>;
+			gpio-controller;
+			gpio-ranges = <&tlmm 0 0 146>;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
+
+			sdc1_off: sdc1-off {
+				clk {
+					pins = "sdc1_clk";
+					bias-disable;
+					drive-strength = <2>;
 				};
 
-				opp-200000000 {
-					opp-hz = /bits/ 64 <200000000>;
+				cmd {
+					pins = "sdc1_cmd";
+					bias-pull-up;
+					drive-strength = <2>;
 				};
 
-				opp-27000000 {
-					opp-hz = /bits/ 64 <27000000>;
+				data {
+					pins = "sdc1_data";
+					bias-pull-up;
+					drive-strength = <2>;
+				};
+			};
+
+			sdc2_off: sdc2-off {
+				clk {
+					pins = "sdc2_clk";
+					bias-disable;
+					drive-strength = <2>;
+				};
+
+				cmd {
+					pins = "sdc2_cmd";
+					bias-pull-up;
+					drive-strength = <2>;
+				};
+
+				data {
+					pins = "sdc2_data";
+					bias-pull-up;
+					drive-strength = <2>;
+				};
+
+				cd {
+					pins = "gpio54";
+					bias-disable;
+					drive-strength = <2>;
+				};
+			};
+
+			blsp1_uart2_default: blsp1-uart2-default {
+				rx {
+					pins = "gpio5";
+					function = "blsp_uart2";
+					drive-strength = <2>;
+					bias-pull-up;
+				};
+
+				tx {
+					pins = "gpio4";
+					function = "blsp_uart2";
+					drive-strength = <4>;
+					bias-disable;
+				};
+			};
+
+			blsp2_uart1_default: blsp2-uart1-default {
+				tx-rts {
+					pins = "gpio41", "gpio44";
+					function = "blsp_uart7";
+					drive-strength = <2>;
+					bias-disable;
+				};
+
+				rx-cts {
+					pins = "gpio42", "gpio43";
+					function = "blsp_uart7";
+					drive-strength = <2>;
+					bias-pull-up;
+				};
+			};
+
+			blsp2_uart1_sleep: blsp2-uart1-sleep {
+				pins = "gpio41", "gpio42", "gpio43", "gpio44";
+				function = "gpio";
+				drive-strength = <2>;
+				bias-pull-down;
+			};
+
+			blsp2_uart4_default: blsp2-uart4-default {
+				tx-rts {
+					pins = "gpio53", "gpio56";
+					function = "blsp_uart10";
+					drive-strength = <2>;
+					bias-disable;
+				};
+
+				rx-cts {
+					pins = "gpio54", "gpio55";
+					function = "blsp_uart10";
+					drive-strength = <2>;
+					bias-pull-up;
+				};
+			};
+
+			blsp1_i2c1_default: blsp1-i2c1-default {
+				pins = "gpio2", "gpio3";
+				function = "blsp_i2c1";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			blsp1_i2c1_sleep: blsp1-i2c1-sleep {
+				pins = "gpio2", "gpio3";
+				function = "blsp_i2c1";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			blsp1_i2c2_default: blsp1-i2c2-default {
+				pins = "gpio6", "gpio7";
+				function = "blsp_i2c2";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			blsp1_i2c2_sleep: blsp1-i2c2-sleep {
+				pins = "gpio6", "gpio7";
+				function = "blsp_i2c2";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			blsp1_i2c3_default: blsp1-i2c3-default {
+				pins = "gpio10", "gpio11";
+				function = "blsp_i2c3";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			blsp1_i2c3_sleep: blsp1-i2c3-sleep {
+				pins = "gpio10", "gpio11";
+				function = "blsp_i2c3";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			/* BLSP1_I2C4 info is missing */
+
+			/* BLSP1_I2C5 info is missing */
+
+			blsp1_i2c6_default: blsp1-i2c6-default {
+				pins = "gpio29", "gpio30";
+				function = "blsp_i2c6";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			blsp1_i2c6_sleep: blsp1-i2c6-sleep {
+				pins = "gpio29", "gpio30";
+				function = "blsp_i2c6";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+			/* 6 interfaces per QUP, BLSP2 indexes are numbered (n)+6 */
+
+			/* BLSP2_I2C1 info is missing */
+
+			blsp2_i2c2_default: blsp2-i2c2-default {
+				pins = "gpio47", "gpio48";
+				function = "blsp_i2c8";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			blsp2_i2c2_sleep: blsp2-i2c2-sleep {
+				pins = "gpio47", "gpio48";
+				function = "blsp_i2c8";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			/* BLSP2_I2C3 info is missing */
+
+			/* BLSP2_I2C4 info is missing */
+
+			blsp2_i2c5_default: blsp2-i2c5-default {
+				pins = "gpio83", "gpio84";
+				function = "blsp_i2c11";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			blsp2_i2c5_sleep: blsp2-i2c5-sleep {
+				pins = "gpio83", "gpio84";
+				function = "blsp_i2c11";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			blsp2_i2c6_default: blsp2-i2c6-default {
+				pins = "gpio87", "gpio88";
+				function = "blsp_i2c12";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			blsp2_i2c6_sleep: blsp2-i2c6-sleep {
+				pins = "gpio87", "gpio88";
+				function = "blsp_i2c12";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			spi8_default: spi8_default {
+				mosi {
+					pins = "gpio45";
+					function = "blsp_spi8";
+				};
+				miso {
+					pins = "gpio46";
+					function = "blsp_spi8";
+				};
+				cs {
+					pins = "gpio47";
+					function = "blsp_spi8";
+				};
+				clk {
+					pins = "gpio48";
+					function = "blsp_spi8";
 				};
 			};
 		};
 
-		mdss: mdss@fd900000 {
-			status = "disabled";
+		mmcc: clock-controller@fd8c0000 {
+			compatible = "qcom,mmcc-msm8974";
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+			#power-domain-cells = <1>;
+			reg = <0xfd8c0000 0x6000>;
+		};
 
+		mdss: mdss@fd900000 {
 			compatible = "qcom,mdss";
-			reg = <0xfd900000 0x100>,
-			      <0xfd924000 0x1000>;
-			reg-names = "mdss_phys",
-			            "vbif_phys";
+			reg = <0xfd900000 0x100>, <0xfd924000 0x1000>;
+			reg-names = "mdss_phys", "vbif_phys";
 
 			power-domains = <&mmcc MDSS_GDSC>;
 
 			clocks = <&mmcc MDSS_AHB_CLK>,
-			         <&mmcc MDSS_AXI_CLK>,
-			         <&mmcc MDSS_VSYNC_CLK>;
-			clock-names = "iface",
-			              "bus",
-			              "vsync";
+				 <&mmcc MDSS_AXI_CLK>,
+				 <&mmcc MDSS_VSYNC_CLK>;
+			clock-names = "iface", "bus", "vsync";
 
 			interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
 
 			interrupt-controller;
 			#interrupt-cells = <1>;
 
+			status = "disabled";
+
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges;
 
 			mdp: mdp@fd900000 {
-				status = "disabled";
-
 				compatible = "qcom,mdp5";
 				reg = <0xfd900100 0x22000>;
 				reg-names = "mdp_phys";
 
 				interrupt-parent = <&mdss>;
-				interrupts = <0 0>;
+				interrupts = <0>;
 
 				clocks = <&mmcc MDSS_AHB_CLK>,
 					 <&mmcc MDSS_AXI_CLK>,
 					 <&mmcc MDSS_MDP_CLK>,
 					 <&mmcc MDSS_VSYNC_CLK>;
-				clock-names = "iface",
-				              "bus",
-				              "core",
-				              "vsync";
+				clock-names = "iface", "bus", "core", "vsync";
 
 				interconnects = <&mmssnoc MNOC_MAS_MDP_PORT0 &bimc BIMC_SLV_EBI_CH0>;
 				interconnect-names = "mdp0-mem";
@@ -1523,38 +1545,39 @@
 			};
 
 			dsi0: dsi@fd922800 {
-				status = "disabled";
-
 				compatible = "qcom,mdss-dsi-ctrl";
 				reg = <0xfd922800 0x1f8>;
 				reg-names = "dsi_ctrl";
 
 				interrupt-parent = <&mdss>;
-				interrupts = <4 IRQ_TYPE_LEVEL_HIGH>;
+				interrupts = <4>;
 
-				assigned-clocks = <&mmcc BYTE0_CLK_SRC>,
-				                  <&mmcc PCLK0_CLK_SRC>;
-				assigned-clock-parents = <&dsi_phy0 0>,
-				                         <&dsi_phy0 1>;
+				assigned-clocks = <&mmcc BYTE0_CLK_SRC>, <&mmcc PCLK0_CLK_SRC>;
+				assigned-clock-parents = <&dsi0_phy 0>, <&dsi0_phy 1>;
 
 				clocks = <&mmcc MDSS_MDP_CLK>,
-				         <&mmcc MDSS_AHB_CLK>,
-				         <&mmcc MDSS_AXI_CLK>,
-				         <&mmcc MDSS_BYTE0_CLK>,
-				         <&mmcc MDSS_PCLK0_CLK>,
-				         <&mmcc MDSS_ESC0_CLK>,
-				         <&mmcc MMSS_MISC_AHB_CLK>;
+					 <&mmcc MDSS_AHB_CLK>,
+					 <&mmcc MDSS_AXI_CLK>,
+					 <&mmcc MDSS_BYTE0_CLK>,
+					 <&mmcc MDSS_PCLK0_CLK>,
+					 <&mmcc MDSS_ESC0_CLK>,
+					 <&mmcc MMSS_MISC_AHB_CLK>;
 				clock-names = "mdp_core",
-				              "iface",
-				              "bus",
-				              "byte",
-				              "pixel",
-				              "core",
-				              "core_mmss";
-
-				phys = <&dsi_phy0>;
+					      "iface",
+					      "bus",
+					      "byte",
+					      "pixel",
+					      "core",
+					      "core_mmss";
+
+				phys = <&dsi0_phy>;
 				phy-names = "dsi-phy";
 
+				status = "disabled";
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+
 				ports {
 					#address-cells = <1>;
 					#size-cells = <0>;
@@ -1574,29 +1597,119 @@
 				};
 			};
 
-			dsi_phy0: dsi-phy@fd922a00 {
-				status = "disabled";
-
+			dsi0_phy: dsi-phy@fd922a00 {
 				compatible = "qcom,dsi-phy-28nm-hpm";
 				reg = <0xfd922a00 0xd4>,
 				      <0xfd922b00 0x280>,
 				      <0xfd922d80 0x30>;
 				reg-names = "dsi_pll",
-				            "dsi_phy",
-				            "dsi_phy_regulator";
+					    "dsi_phy",
+					    "dsi_phy_regulator";
 
 				#clock-cells = <1>;
 				#phy-cells = <0>;
-				qcom,dsi-phy-index = <0>;
 
 				clocks = <&mmcc MDSS_AHB_CLK>, <&xo_board>;
 				clock-names = "iface", "ref";
+
+				status = "disabled";
+			};
+		};
+
+		gpu: adreno@fdb00000 {
+			compatible = "qcom,adreno-330.1", "qcom,adreno";
+			reg = <0xfdb00000 0x10000>;
+			reg-names = "kgsl_3d0_reg_memory";
+
+			interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "kgsl_3d0_irq";
+
+			clocks = <&mmcc OXILI_GFX3D_CLK>,
+				 <&mmcc OXILICX_AHB_CLK>,
+				 <&mmcc OXILICX_AXI_CLK>;
+			clock-names = "core", "iface", "mem_iface";
+
+			sram = <&gmu_sram>;
+			power-domains = <&mmcc OXILICX_GDSC>;
+			operating-points-v2 = <&gpu_opp_table>;
+
+			interconnects = <&mmssnoc MNOC_MAS_GRAPHICS_3D &bimc BIMC_SLV_EBI_CH0>,
+					<&ocmemnoc OCMEM_VNOC_MAS_GFX3D &ocmemnoc OCMEM_SLV_OCMEM>;
+			interconnect-names = "gfx-mem", "ocmem";
+
+			// iommus = <&gpu_iommu 0>;
+
+			status = "disabled";
+
+			gpu_opp_table: opp-table {
+				compatible = "operating-points-v2";
+
+				opp-320000000 {
+					opp-hz = /bits/ 64 <320000000>;
+				};
+
+				opp-200000000 {
+					opp-hz = /bits/ 64 <200000000>;
+				};
+
+				opp-27000000 {
+					opp-hz = /bits/ 64 <27000000>;
+				};
+			};
+		};
+
+		sram@fdd00000 {
+			compatible = "qcom,msm8974-ocmem";
+			reg = <0xfdd00000 0x2000>,
+			      <0xfec00000 0x180000>;
+			reg-names = "ctrl", "mem";
+			ranges = <0 0xfec00000 0x180000>;
+			clocks = <&rpmcc RPM_SMD_OCMEMGX_CLK>,
+				 <&mmcc OCMEMCX_OCMEMNOC_CLK>;
+			clock-names = "core", "iface";
+
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			gmu_sram: gmu-sram@0 {
+				reg = <0x0 0x100000>;
 			};
 		};
 
-		imem@fe805000 {
+		remoteproc_adsp: remoteproc@fe200000 {
+			compatible = "qcom,msm8974-adsp-pil";
+			reg = <0xfe200000 0x100>;
+
+			interrupts-extended = <&intc GIC_SPI 162 IRQ_TYPE_EDGE_RISING>,
+					       <&adsp_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
+					       <&adsp_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
+					       <&adsp_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
+					       <&adsp_smp2p_in 3 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "wdog", "fatal", "ready", "handover", "stop-ack";
+
+			clocks = <&xo_board>;
+			clock-names = "xo";
+
+			memory-region = <&adsp_region>;
+
+			qcom,smem-states = <&adsp_smp2p_out 0>;
+			qcom,smem-state-names = "stop";
+
 			status = "disabled";
-			compatible = "syscon", "simple-mfd";
+
+			smd-edge {
+				interrupts = <GIC_SPI 156 IRQ_TYPE_EDGE_RISING>;
+
+				qcom,ipc = <&apcs 8 8>;
+				qcom,smd-edge = <1>;
+				label = "lpass";
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+
+		imem: sram@fe805000 {
+			compatible = "qcom,msm8974-imem", "syscon", "simple-mfd";
 			reg = <0xfe805000 0x1000>;
 
 			reboot-mode {
@@ -1606,76 +1719,194 @@
 		};
 	};
 
-	smd {
-		compatible = "qcom,smd";
+	tcsr_mutex: tcsr-mutex {
+		compatible = "qcom,tcsr-mutex";
+		syscon = <&tcsr_mutex_block 0 0x80>;
 
-		rpm {
-			interrupts = <GIC_SPI 168 IRQ_TYPE_EDGE_RISING>;
-			qcom,ipc = <&apcs 8 0>;
-			qcom,smd-edge = <15>;
+		#hwlock-cells = <1>;
+	};
 
-			rpm_requests {
-				compatible = "qcom,rpm-msm8974";
-				qcom,smd-channels = "rpm_requests";
+	thermal-zones {
+		cpu0-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
 
-				rpmcc: clock-controller {
-					compatible = "qcom,rpmcc-msm8974", "qcom,rpmcc";
-					#clock-cells = <1>;
+			thermal-sensors = <&tsens 5>;
+
+			trips {
+				cpu_alert0: trip0 {
+					temperature = <75000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+				cpu_crit0: trip1 {
+					temperature = <110000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+
+		cpu1-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 6>;
+
+			trips {
+				cpu_alert1: trip0 {
+					temperature = <75000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+				cpu_crit1: trip1 {
+					temperature = <110000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+
+		cpu2-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 7>;
+
+			trips {
+				cpu_alert2: trip0 {
+					temperature = <75000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+				cpu_crit2: trip1 {
+					temperature = <110000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+
+		cpu3-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 8>;
+
+			trips {
+				cpu_alert3: trip0 {
+					temperature = <75000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+				cpu_crit3: trip1 {
+					temperature = <110000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+
+		q6-dsp-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 1>;
+
+			trips {
+				q6_dsp_alert0: trip-point0 {
+					temperature = <90000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+			};
+		};
+
+		modemtx-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 2>;
+
+			trips {
+				modemtx_alert0: trip-point0 {
+					temperature = <90000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+			};
+		};
+
+		video-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 3>;
+
+			trips {
+				video_alert0: trip-point0 {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+			};
+		};
+
+		wlan-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 4>;
+
+			trips {
+				wlan_alert0: trip-point0 {
+					temperature = <105000>;
+					hysteresis = <2000>;
+					type = "hot";
 				};
+			};
+		};
+
+		gpu-top-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
 
-				pm8841-regulators {
-					compatible = "qcom,rpm-pm8841-regulators";
-
-					pm8841_s1: s1 {};
-					pm8841_s2: s2 {};
-					pm8841_s3: s3 {};
-					pm8841_s4: s4 {};
-					pm8841_s5: s5 {};
-					pm8841_s6: s6 {};
-					pm8841_s7: s7 {};
-					pm8841_s8: s8 {};
+			thermal-sensors = <&tsens 9>;
+
+			trips {
+				gpu1_alert0: trip-point0 {
+					temperature = <90000>;
+					hysteresis = <2000>;
+					type = "hot";
 				};
+			};
+		};
 
-				pm8941-regulators {
-					compatible = "qcom,rpm-pm8941-regulators";
-
-					pm8941_s1: s1 {};
-					pm8941_s2: s2 {};
-					pm8941_s3: s3 {};
-
-					pm8941_l1: l1 {};
-					pm8941_l2: l2 {};
-					pm8941_l3: l3 {};
-					pm8941_l4: l4 {};
-					pm8941_l5: l5 {};
-					pm8941_l6: l6 {};
-					pm8941_l7: l7 {};
-					pm8941_l8: l8 {};
-					pm8941_l9: l9 {};
-					pm8941_l10: l10 {};
-					pm8941_l11: l11 {};
-					pm8941_l12: l12 {};
-					pm8941_l13: l13 {};
-					pm8941_l14: l14 {};
-					pm8941_l15: l15 {};
-					pm8941_l16: l16 {};
-					pm8941_l17: l17 {};
-					pm8941_l18: l18 {};
-					pm8941_l19: l19 {};
-					pm8941_l20: l20 {};
-					pm8941_l21: l21 {};
-					pm8941_l22: l22 {};
-					pm8941_l23: l23 {};
-					pm8941_l24: l24 {};
-
-					pm8941_lvs1: lvs1 {};
-					pm8941_lvs2: lvs2 {};
-					pm8941_lvs3: lvs3 {};
+		gpu-bottom-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 10>;
+
+			trips {
+				gpu2_alert0: trip-point0 {
+					temperature = <90000>;
+					hysteresis = <2000>;
+					type = "hot";
 				};
 			};
 		};
 	};
 
+	timer {
+		compatible = "arm,armv7-timer";
+		interrupts = <GIC_PPI 2 0xf08>,
+			     <GIC_PPI 3 0xf08>,
+			     <GIC_PPI 4 0xf08>,
+			     <GIC_PPI 1 0xf08>;
+		clock-frequency = <19200000>;
+	};
+
 	vreg_boost: vreg-boost {
 		compatible = "regulator-fixed";
 
@@ -1692,6 +1923,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&boost_bypass_n_pin>;
 	};
+
 	vreg_vph_pwr: vreg-vph-pwr {
 		compatible = "regulator-fixed";
 		regulator-name = "vph-pwr";
diff --git a/arch/arm/boot/dts/qcom-msm8974pro-fairphone-fp2.dts b/arch/arm/boot/dts/qcom-msm8974pro-fairphone-fp2.dts
new file mode 100644
index 000000000000..ff6e0066768b
--- /dev/null
+++ b/arch/arm/boot/dts/qcom-msm8974pro-fairphone-fp2.dts
@@ -0,0 +1,464 @@
+// SPDX-License-Identifier: GPL-2.0
+#include "qcom-msm8974pro.dtsi"
+#include "qcom-pm8841.dtsi"
+#include "qcom-pm8941.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+
+/ {
+	model = "Fairphone 2";
+	compatible = "fairphone,fp2", "qcom,msm8974";
+
+	aliases {
+		mmc0 = &sdhc_1;
+		mmc1 = &sdhc_2;
+		serial0 = &blsp1_uart2;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_keys_pin_a>;
+
+		key-camera-snapshot {
+			label = "camera_snapshot";
+			gpios = <&pm8941_gpios 1 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_CAMERA>;
+			wakeup-source;
+			debounce-interval = <15>;
+		};
+
+		key-volume-down {
+			label = "volume_down";
+			gpios = <&pm8941_gpios 2 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEDOWN>;
+			wakeup-source;
+			debounce-interval = <15>;
+		};
+
+		key-volume-up {
+			label = "volume_up";
+			gpios = <&pm8941_gpios 5 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+			wakeup-source;
+			debounce-interval = <15>;
+		};
+	};
+
+	vibrator {
+		compatible = "gpio-vibrator";
+		enable-gpios = <&tlmm 86 GPIO_ACTIVE_HIGH>;
+		vcc-supply = <&pm8941_l18>;
+	};
+};
+
+&blsp1_i2c2 {
+	status = "okay";
+
+	touchscreen@41 {
+		compatible = "ilitek,ili2120";
+		reg = <0x41>;
+		interrupt-parent = <&tlmm>;
+		interrupts = <28 IRQ_TYPE_EDGE_FALLING>;
+		reset-gpios = <&tlmm 55 GPIO_ACTIVE_LOW>;
+
+		touchscreen-size-x = <1080>;
+		touchscreen-size-y = <1920>;
+	};
+};
+
+&blsp1_uart2 {
+	status = "okay";
+};
+
+&imem {
+	reboot-mode {
+		mode-normal = <0x77665501>;
+		mode-bootloader = <0x77665500>;
+		mode-recovery = <0x77665502>;
+	};
+};
+
+&otg {
+	status = "okay";
+
+	phys = <&usb_hs1_phy>;
+	phy-select = <&tcsr 0xb000 0>;
+	extcon = <&smbb>, <&usb_id>;
+	vbus-supply = <&chg_otg>;
+
+	hnp-disable;
+	srp-disable;
+	adp-disable;
+
+	ulpi {
+		phy@a {
+			status = "okay";
+
+			v1p8-supply = <&pm8941_l6>;
+			v3p3-supply = <&pm8941_l24>;
+
+			extcon = <&smbb>;
+			qcom,init-seq = /bits/ 8 <0x1 0x64>;
+		};
+	};
+};
+
+&pm8941_gpios {
+	gpio_keys_pin_a: gpio-keys-active-state {
+		pins = "gpio1", "gpio2", "gpio5";
+		function = "normal";
+
+		bias-pull-up;
+		power-source = <PM8941_GPIO_S3>;
+	};
+};
+
+&pm8941_lpg {
+	status = "okay";
+
+	qcom,power-source = <1>;
+
+	multi-led {
+		color = <LED_COLOR_ID_RGB>;
+		function = LED_FUNCTION_STATUS;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		led@7 {
+			reg = <7>;
+			color = <LED_COLOR_ID_RED>;
+		};
+
+		led@6 {
+			reg = <6>;
+			color = <LED_COLOR_ID_GREEN>;
+		};
+
+		led@5 {
+			reg = <5>;
+			color = <LED_COLOR_ID_BLUE>;
+		};
+	};
+};
+
+&pronto {
+	status = "okay";
+
+	vddmx-supply = <&pm8841_s1>;
+	vddcx-supply = <&pm8841_s2>;
+	vddpx-supply = <&pm8941_s3>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&wcnss_pin_a>;
+
+	iris {
+		vddxo-supply = <&pm8941_l6>;
+		vddrfa-supply = <&pm8941_l11>;
+		vddpa-supply = <&pm8941_l19>;
+		vdddig-supply = <&pm8941_s3>;
+	};
+
+	smd-edge {
+		qcom,remote-pid = <4>;
+		label = "pronto";
+
+		wcnss {
+			status = "okay";
+		};
+	};
+};
+
+&remoteproc_adsp {
+	status = "okay";
+	cx-supply = <&pm8841_s2>;
+};
+
+&remoteproc_mss {
+	status = "okay";
+	cx-supply = <&pm8841_s2>;
+	mss-supply = <&pm8841_s3>;
+	mx-supply = <&pm8841_s1>;
+	pll-supply = <&pm8941_l12>;
+};
+
+&rpm_requests {
+	pm8841-regulators {
+		compatible = "qcom,rpm-pm8841-regulators";
+
+		pm8841_s1: s1 {
+			regulator-min-microvolt = <675000>;
+			regulator-max-microvolt = <1050000>;
+		};
+
+		pm8841_s2: s2 {
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1050000>;
+		};
+
+		pm8841_s3: s3 {
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1050000>;
+		};
+	};
+
+	pm8941-regulators {
+		compatible = "qcom,rpm-pm8941-regulators";
+
+		vdd_l1_l3-supply = <&pm8941_s1>;
+		vdd_l2_lvs1_2_3-supply = <&pm8941_s3>;
+		vdd_l4_l11-supply = <&pm8941_s1>;
+		vdd_l5_l7-supply = <&pm8941_s2>;
+		vdd_l6_l12_l14_l15-supply = <&pm8941_s2>;
+		vdd_l9_l10_l17_l22-supply = <&vreg_boost>;
+		vdd_l13_l20_l23_l24-supply = <&vreg_boost>;
+		vdd_l21-supply = <&vreg_boost>;
+
+		pm8941_s1: s1 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		pm8941_s2: s2 {
+			regulator-min-microvolt = <2150000>;
+			regulator-max-microvolt = <2150000>;
+			regulator-boot-on;
+		};
+
+		pm8941_s3: s3 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		pm8941_l1: l1 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		pm8941_l2: l2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8941_l3: l3 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+		};
+
+		pm8941_l4: l4 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+		};
+
+		pm8941_l5: l5 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8941_l6: l6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-boot-on;
+		};
+
+		pm8941_l7: l7 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-boot-on;
+		};
+
+		pm8941_l8: l8 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8941_l9: l9 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8941_l10: l10 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8941_l11: l11 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1350000>;
+		};
+
+		pm8941_l12: l12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		pm8941_l13: l13 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-boot-on;
+		};
+
+		pm8941_l14: l14 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8941_l15: l15 {
+			regulator-min-microvolt = <2050000>;
+			regulator-max-microvolt = <2050000>;
+		};
+
+		pm8941_l16: l16 {
+			regulator-min-microvolt = <2700000>;
+			regulator-max-microvolt = <2700000>;
+		};
+
+		pm8941_l17: l17 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+		};
+
+		pm8941_l18: l18 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+		};
+
+		pm8941_l19: l19 {
+			regulator-min-microvolt = <2900000>;
+			regulator-max-microvolt = <3350000>;
+		};
+
+		pm8941_l20: l20 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-system-load = <200000>;
+			regulator-allow-set-load;
+			regulator-boot-on;
+		};
+
+		pm8941_l21: l21 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-boot-on;
+		};
+
+		pm8941_l22: l22 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3300000>;
+		};
+
+		pm8941_l23: l23 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+		};
+
+		pm8941_l24: l24 {
+			regulator-min-microvolt = <3075000>;
+			regulator-max-microvolt = <3075000>;
+			regulator-boot-on;
+		};
+	};
+};
+
+&sdhc_1 {
+	status = "okay";
+
+	vmmc-supply = <&pm8941_l20>;
+	vqmmc-supply = <&pm8941_s3>;
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sdc1_on>;
+	pinctrl-1 = <&sdc1_off>;
+};
+
+&sdhc_2 {
+	status = "okay";
+
+	vmmc-supply = <&pm8941_l21>;
+	vqmmc-supply = <&pm8941_l13>;
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sdc2_on>;
+	pinctrl-1 = <&sdc2_off>;
+};
+
+&smbb {
+	usb-charge-current-limit = <1500000>;
+	qcom,fast-charge-safe-current = <1500000>;
+	qcom,fast-charge-current-limit = <1500000>;
+	qcom,fast-charge-safe-voltage = <4380000>;
+	qcom,fast-charge-high-threshold-voltage = <4350000>;
+	qcom,auto-recharge-threshold-voltage = <4240000>;
+	qcom,minimum-input-voltage = <4450000>;
+};
+
+&tlmm {
+	sdc1_on: sdc1-on {
+		clk {
+			pins = "sdc1_clk";
+			drive-strength = <16>;
+			bias-disable;
+		};
+
+		cmd-data {
+			pins = "sdc1_cmd", "sdc1_data";
+			drive-strength = <10>;
+			bias-pull-up;
+		};
+	};
+
+	sdc2_on: sdc2-on {
+		clk {
+			pins = "sdc2_clk";
+			drive-strength = <10>;
+			bias-disable;
+		};
+
+		cmd-data {
+			pins = "sdc2_cmd", "sdc2_data";
+			drive-strength = <6>;
+			bias-pull-up;
+		};
+	};
+
+	wcnss_pin_a: wcnss-pin-active {
+		wlan {
+			pins =  "gpio36", "gpio37", "gpio38", "gpio39", "gpio40";
+			function = "wlan";
+
+			drive-strength = <6>;
+			bias-pull-down;
+		};
+
+		bt {
+			pins = "gpio35", "gpio43", "gpio44";
+			function = "bt";
+
+			drive-strength = <2>;
+			bias-pull-down;
+		};
+
+		fm {
+			pins = "gpio41", "gpio42";
+			function = "fm";
+
+			drive-strength = <2>;
+			bias-pull-down;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/qcom-msm8974pro-samsung-klte.dts b/arch/arm/boot/dts/qcom-msm8974pro-samsung-klte.dts
new file mode 100644
index 000000000000..983e10c3d863
--- /dev/null
+++ b/arch/arm/boot/dts/qcom-msm8974pro-samsung-klte.dts
@@ -0,0 +1,815 @@
+// SPDX-License-Identifier: GPL-2.0
+#include "qcom-msm8974pro.dtsi"
+#include "qcom-pma8084.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+	model = "Samsung Galaxy S5";
+	compatible = "samsung,klte", "qcom,msm8974";
+
+	aliases {
+		serial0 = &blsp1_uart1;
+		mmc0 = &sdhc_1; /* SDC1 eMMC slot */
+		mmc1 = &sdhc_3; /* SDC2 SD card slot */
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_keys_pin_a>;
+
+		key-volume-down {
+			label = "volume_down";
+			gpios = <&pma8084_gpios 2 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			linux,code = <KEY_VOLUMEDOWN>;
+			debounce-interval = <15>;
+		};
+
+		key-home {
+			label = "home_key";
+			gpios = <&pma8084_gpios 3 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			linux,code = <KEY_HOMEPAGE>;
+			wakeup-source;
+			debounce-interval = <15>;
+		};
+
+		key-volume-up {
+			label = "volume_up";
+			gpios = <&pma8084_gpios 5 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			linux,code = <KEY_VOLUMEUP>;
+			debounce-interval = <15>;
+		};
+	};
+
+	i2c-gpio-touchkey {
+		compatible = "i2c-gpio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		sda-gpios = <&tlmm 95 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&tlmm 96 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c_touchkey_pins>;
+
+		touchkey@20 {
+			compatible = "cypress,tm2-touchkey";
+			reg = <0x20>;
+
+			interrupt-parent = <&pma8084_gpios>;
+			interrupts = <6 IRQ_TYPE_EDGE_FALLING>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&touchkey_pin>;
+
+			vcc-supply = <&max77826_ldo15>;
+			vdd-supply = <&pma8084_l19>;
+
+			linux,keycodes = <KEY_APPSELECT KEY_BACK>;
+		};
+	};
+
+	i2c-gpio-led {
+		compatible = "i2c-gpio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		scl-gpios = <&tlmm 121 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		sda-gpios = <&tlmm 120 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c_led_gpioex_pins>;
+
+		i2c-gpio,delay-us = <2>;
+
+		gpio_expander: gpio@20 {
+			compatible = "nxp,pcal6416";
+			reg = <0x20>;
+
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			vcc-supply = <&pma8084_s4>;
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&gpioex_pin>;
+
+			reset-gpios = <&tlmm 145 GPIO_ACTIVE_LOW>;
+		};
+
+		led-controller@30 {
+			compatible = "panasonic,an30259a";
+			reg = <0x30>;
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			led@1 {
+				reg = <1>;
+				function = LED_FUNCTION_STATUS;
+				color = <LED_COLOR_ID_RED>;
+			};
+
+			led@2 {
+				reg = <2>;
+				function = LED_FUNCTION_STATUS;
+				color = <LED_COLOR_ID_GREEN>;
+			};
+
+			led@3 {
+				reg = <3>;
+				function = LED_FUNCTION_STATUS;
+				color = <LED_COLOR_ID_BLUE>;
+			};
+		};
+	};
+
+	vreg_wlan: wlan-regulator {
+		compatible = "regulator-fixed";
+
+		regulator-name = "wl-reg";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&gpio_expander 8 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	vreg_panel: panel-regulator {
+		compatible = "regulator-fixed";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&panel_en_pin>;
+
+		regulator-name = "panel-vddr-reg";
+		regulator-min-microvolt = <1500000>;
+		regulator-max-microvolt = <1500000>;
+
+		gpio = <&pma8084_gpios 14 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	/delete-node/ vreg-boost;
+};
+
+&blsp1_i2c2 {
+	status = "okay";
+
+	touchscreen@20 {
+		compatible = "syna,rmi4-i2c";
+		reg = <0x20>;
+
+		interrupt-parent = <&pma8084_gpios>;
+		interrupts = <8 IRQ_TYPE_EDGE_FALLING>;
+
+		vdd-supply = <&max77826_ldo13>;
+		vio-supply = <&pma8084_lvs2>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&touch_pin>;
+
+		syna,startup-delay-ms = <100>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		rmi4-f01@1 {
+			reg = <0x1>;
+			syna,nosleep-mode = <1>;
+		};
+
+		rmi4-f12@12 {
+			reg = <0x12>;
+			syna,sensor-type = <1>;
+		};
+	};
+};
+
+&blsp1_i2c6 {
+	status = "okay";
+
+	pmic@60 {
+		reg = <0x60>;
+		compatible = "maxim,max77826";
+
+		regulators {
+			max77826_ldo1: LDO1 {
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+			};
+
+			max77826_ldo2: LDO2 {
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <1000000>;
+			};
+
+			max77826_ldo3: LDO3 {
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+			};
+
+			max77826_ldo4: LDO4 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+
+			max77826_ldo5: LDO5 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+
+			max77826_ldo6: LDO6 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			max77826_ldo7: LDO7 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+
+			max77826_ldo8: LDO8 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			max77826_ldo9: LDO9 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+
+			max77826_ldo10: LDO10 {
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2950000>;
+			};
+
+			max77826_ldo11: LDO11 {
+				regulator-min-microvolt = <2700000>;
+				regulator-max-microvolt = <2950000>;
+			};
+
+			max77826_ldo12: LDO12 {
+				regulator-min-microvolt = <2500000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			max77826_ldo13: LDO13 {
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			max77826_ldo14: LDO14 {
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			max77826_ldo15: LDO15 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+
+			max77826_buck: BUCK {
+				regulator-min-microvolt = <1225000>;
+				regulator-max-microvolt = <1225000>;
+			};
+
+			max77826_buckboost: BUCKBOOST {
+				regulator-min-microvolt = <3400000>;
+				regulator-max-microvolt = <3400000>;
+			};
+		};
+	};
+};
+
+&blsp1_uart2 {
+	status = "okay";
+};
+
+&blsp2_i2c6 {
+	status = "okay";
+
+	fuelgauge@36 {
+		compatible = "maxim,max17048";
+		reg = <0x36>;
+
+		maxim,double-soc;
+		maxim,rcomp = /bits/ 8 <0x56>;
+
+		interrupt-parent = <&pma8084_gpios>;
+		interrupts = <21 IRQ_TYPE_LEVEL_LOW>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&fuelgauge_pin>;
+	};
+};
+
+&blsp2_uart2 {
+	status = "okay";
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&blsp2_uart2_pins_active>;
+	pinctrl-1 = <&blsp2_uart2_pins_sleep>;
+
+	bluetooth {
+		compatible = "brcm,bcm43540-bt";
+		max-speed = <3000000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&bt_pins>;
+		device-wakeup-gpios = <&tlmm 91 GPIO_ACTIVE_HIGH>;
+		shutdown-gpios = <&gpio_expander 9 GPIO_ACTIVE_HIGH>;
+		interrupt-parent = <&tlmm>;
+		interrupts = <75 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "host-wakeup";
+	};
+};
+
+&dsi0 {
+	status = "okay";
+
+	vdda-supply = <&pma8084_l2>;
+	vdd-supply = <&pma8084_l22>;
+	vddio-supply = <&pma8084_l12>;
+
+	panel: panel@0 {
+		reg = <0>;
+		compatible = "samsung,s6e3fa2";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&panel_te_pin &panel_rst_pin>;
+
+		iovdd-supply = <&pma8084_lvs4>;
+		vddr-supply = <&vreg_panel>;
+
+		reset-gpios = <&pma8084_gpios 17 GPIO_ACTIVE_LOW>;
+		te-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&dsi0_out>;
+			};
+		};
+	};
+};
+
+&dsi0_out {
+	remote-endpoint = <&panel_in>;
+	data-lanes = <0 1 2 3>;
+};
+
+&dsi0_phy {
+	status = "okay";
+
+	vddio-supply = <&pma8084_l12>;
+};
+
+&gpu {
+	status = "okay";
+};
+
+&mdss {
+	status = "okay";
+};
+
+&otg {
+	status = "okay";
+
+	phys = <&usb_hs1_phy>;
+	phy-select = <&tcsr 0xb000 0>;
+
+	hnp-disable;
+	srp-disable;
+	adp-disable;
+
+	ulpi {
+		phy@a {
+			status = "okay";
+
+			v1p8-supply = <&pma8084_l6>;
+			v3p3-supply = <&pma8084_l24>;
+
+			qcom,init-seq = /bits/ 8 <0x1 0x64>;
+		};
+	};
+};
+
+&pma8084_gpios {
+	gpio_keys_pin_a: gpio-keys-active-state {
+		pins = "gpio2", "gpio3", "gpio5";
+		function = "normal";
+
+		bias-pull-up;
+		power-source = <PMA8084_GPIO_S4>;
+	};
+
+	touchkey_pin: touchkey-int-state {
+		pins = "gpio6";
+		function = "normal";
+		bias-disable;
+		input-enable;
+		power-source = <PMA8084_GPIO_S4>;
+	};
+
+	touch_pin: touchscreen-int-state {
+		pins = "gpio8";
+		function = "normal";
+		bias-disable;
+		input-enable;
+		power-source = <PMA8084_GPIO_S4>;
+	};
+
+	panel_en_pin: panel-en-state {
+		pins = "gpio14";
+		function = "normal";
+		bias-pull-up;
+		power-source = <PMA8084_GPIO_S4>;
+		qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
+	};
+
+	wlan_sleep_clk_pin: wlan-sleep-clk-state {
+		pins = "gpio16";
+		function = "func2";
+
+		output-high;
+		power-source = <PMA8084_GPIO_S4>;
+		qcom,drive-strength = <PMIC_GPIO_STRENGTH_HIGH>;
+	};
+
+	panel_rst_pin: panel-rst-state {
+		pins = "gpio17";
+		function = "normal";
+		bias-disable;
+		power-source = <PMA8084_GPIO_S4>;
+		qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
+	};
+
+	fuelgauge_pin: fuelgauge-int-state {
+		pins = "gpio21";
+		function = "normal";
+		bias-disable;
+		input-enable;
+		power-source = <PMA8084_GPIO_S4>;
+	};
+};
+
+&remoteproc_adsp {
+	status = "okay";
+	cx-supply = <&pma8084_s2>;
+};
+
+&remoteproc_mss {
+	status = "okay";
+	cx-supply = <&pma8084_s2>;
+	mss-supply = <&pma8084_s6>;
+	mx-supply = <&pma8084_s1>;
+	pll-supply = <&pma8084_l12>;
+};
+
+&rpm_requests {
+	pma8084-regulators {
+		compatible = "qcom,rpm-pma8084-regulators";
+
+		pma8084_s1: s1 {
+			regulator-min-microvolt = <675000>;
+			regulator-max-microvolt = <1050000>;
+			regulator-always-on;
+		};
+
+		pma8084_s2: s2 {
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1050000>;
+		};
+
+		pma8084_s3: s3 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+		};
+
+		pma8084_s4: s4 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pma8084_s5: s5 {
+			regulator-min-microvolt = <2150000>;
+			regulator-max-microvolt = <2150000>;
+		};
+
+		pma8084_s6: s6 {
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1050000>;
+		};
+
+		pma8084_l1: l1 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+		};
+
+		pma8084_l2: l2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pma8084_l3: l3 {
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pma8084_l4: l4 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1225000>;
+		};
+
+		pma8084_l5: l5 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pma8084_l6: l6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pma8084_l7: l7 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pma8084_l8: l8 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pma8084_l9: l9 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pma8084_l10: l10 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pma8084_l11: l11 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+		};
+
+		pma8084_l12: l12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+		};
+
+		pma8084_l13: l13 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pma8084_l14: l14 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pma8084_l15: l15 {
+			regulator-min-microvolt = <2050000>;
+			regulator-max-microvolt = <2050000>;
+		};
+
+		pma8084_l16: l16 {
+			regulator-min-microvolt = <2700000>;
+			regulator-max-microvolt = <2700000>;
+		};
+
+		pma8084_l17: l17 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+		};
+
+		pma8084_l18: l18 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+		};
+
+		pma8084_l19: l19 {
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+		};
+
+		pma8084_l20: l20 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-system-load = <200000>;
+			regulator-allow-set-load;
+		};
+
+		pma8084_l21: l21 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-system-load = <200000>;
+			regulator-allow-set-load;
+		};
+
+		pma8084_l22: l22 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3300000>;
+		};
+
+		pma8084_l23: l23 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+		};
+
+		pma8084_l24: l24 {
+			regulator-min-microvolt = <3075000>;
+			regulator-max-microvolt = <3075000>;
+		};
+
+		pma8084_l25: l25 {
+			regulator-min-microvolt = <2100000>;
+			regulator-max-microvolt = <2100000>;
+		};
+
+		pma8084_l26: l26 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2050000>;
+		};
+
+		pma8084_l27: l27 {
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1225000>;
+		};
+
+		pma8084_lvs1: lvs1 {};
+		pma8084_lvs2: lvs2 {};
+		pma8084_lvs3: lvs3 {};
+		pma8084_lvs4: lvs4 {};
+
+		pma8084_5vs1: 5vs1 {};
+	};
+};
+
+&sdhc_1 {
+	status = "okay";
+
+	vmmc-supply = <&pma8084_l20>;
+	vqmmc-supply = <&pma8084_s4>;
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sdc1_on>;
+	pinctrl-1 = <&sdc1_off>;
+};
+
+&sdhc_2 {
+	status = "okay";
+	max-frequency = <100000000>;
+	vmmc-supply = <&vreg_wlan>;
+	vqmmc-supply = <&pma8084_s4>;
+	non-removable;
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sdc2_on>;
+	pinctrl-1 = <&sdc2_off>;
+
+	wifi@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <92 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "host-wake";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&wlan_sleep_clk_pin &wifi_pin>;
+	};
+};
+
+&sdhc_3 {
+	status = "okay";
+	max-frequency = <100000000>;
+	vmmc-supply = <&pma8084_l21>;
+	vqmmc-supply = <&pma8084_l13>;
+
+	/*
+	 * cd-gpio is intentionally disabled. If enabled, an SD card
+	 * present during boot is not initialized correctly. Without
+	 * cd-gpios the driver resorts to polling, so hotplug works.
+	 */
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdc3_on /* &sdhc3_cd_pin */>;
+	/* cd-gpios = <&tlmm 62 GPIO_ACTIVE_LOW>; */
+};
+
+&tlmm {
+	/* This seems suspicious, but somebody with this device should look into it. */
+	blsp2_uart2_pins_active: blsp2-uart2-pins-active {
+		pins = "gpio45", "gpio46", "gpio47", "gpio48";
+		function = "blsp_uart8";
+		drive-strength = <8>;
+		bias-disable;
+	};
+
+	blsp2_uart2_pins_sleep: blsp2-uart2-pins-sleep {
+		pins = "gpio45", "gpio46", "gpio47", "gpio48";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	bt_pins: bt-pins {
+		hostwake {
+			pins = "gpio75";
+			function = "gpio";
+			drive-strength = <16>;
+			input-enable;
+		};
+
+		devwake {
+			pins = "gpio91";
+			function = "gpio";
+			drive-strength = <2>;
+		};
+	};
+
+	sdc1_on: sdhc1-on {
+		clk {
+			pins = "sdc1_clk";
+			drive-strength = <4>;
+			bias-disable;
+		};
+
+		cmd-data {
+			pins = "sdc1_cmd", "sdc1_data";
+			drive-strength = <4>;
+			bias-pull-up;
+		};
+	};
+
+	sdc3_on: sdc3-on {
+		pins = "gpio35", "gpio36", "gpio37", "gpio38", "gpio39", "gpio40";
+		function = "sdc3";
+		drive-strength = <8>;
+		bias-disable;
+	};
+
+	sdhc3_cd_pin: sdc3-cd-on {
+		pins = "gpio62";
+		function = "gpio";
+
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	sdc2_on: sdhc2-on {
+		clk {
+			pins = "sdc2_clk";
+			drive-strength = <6>;
+			bias-disable;
+		};
+
+		cmd-data {
+			pins = "sdc2_cmd", "sdc2_data";
+			drive-strength = <6>;
+			bias-pull-up;
+		};
+	};
+
+	i2c_touchkey_pins: i2c-touchkey {
+		pins = "gpio95", "gpio96";
+		function = "gpio";
+		input-enable;
+		bias-pull-up;
+	};
+
+	i2c_led_gpioex_pins: i2c-led-gpioex {
+		pins = "gpio120", "gpio121";
+		function = "gpio";
+		input-enable;
+		bias-pull-down;
+	};
+
+	gpioex_pin: gpioex {
+		pins = "gpio145";
+		function = "gpio";
+		bias-pull-up;
+		drive-strength = <2>;
+	};
+
+	wifi_pin: wifi {
+		pins = "gpio92";
+		function = "gpio";
+		input-enable;
+		bias-pull-down;
+	};
+
+	panel_te_pin: panel {
+		pins = "gpio12";
+		function = "mdp_vsync";
+		drive-strength = <2>;
+		bias-disable;
+	};
+};
diff --git a/arch/arm/boot/dts/qcom-msm8974pro-sony-xperia-shinano-castor.dts b/arch/arm/boot/dts/qcom-msm8974pro-sony-xperia-shinano-castor.dts
new file mode 100644
index 000000000000..3f45f5c5d37b
--- /dev/null
+++ b/arch/arm/boot/dts/qcom-msm8974pro-sony-xperia-shinano-castor.dts
@@ -0,0 +1,638 @@
+// SPDX-License-Identifier: GPL-2.0
+#include "qcom-msm8974pro.dtsi"
+#include "qcom-pm8841.dtsi"
+#include "qcom-pm8941.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+
+/ {
+	model = "Sony Xperia Z2 Tablet";
+	compatible = "sony,xperia-castor", "qcom,msm8974";
+
+	aliases {
+		serial0 = &blsp1_uart2;
+		serial1 = &blsp2_uart1;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_keys_pin_a>;
+
+		key-volume-down {
+			label = "volume_down";
+			gpios = <&pm8941_gpios 2 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			linux,code = <KEY_VOLUMEDOWN>;
+		};
+
+		key-camera-snapshot {
+			label = "camera_snapshot";
+			gpios = <&pm8941_gpios 3 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			linux,code = <KEY_CAMERA>;
+		};
+
+		key-camera-focus {
+			label = "camera_focus";
+			gpios = <&pm8941_gpios 4 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			linux,code = <KEY_CAMERA_FOCUS>;
+		};
+
+		key-volume-up {
+			label = "volume_up";
+			gpios = <&pm8941_gpios 5 GPIO_ACTIVE_LOW>;
+			linux,input-type = <1>;
+			linux,code = <KEY_VOLUMEUP>;
+		};
+	};
+
+	vreg_bl_vddio: lcd-backlight-vddio {
+		compatible = "regulator-fixed";
+		regulator-name = "vreg_bl_vddio";
+		regulator-min-microvolt = <3150000>;
+		regulator-max-microvolt = <3150000>;
+
+		gpio = <&tlmm 69 0>;
+		enable-active-high;
+
+		vin-supply = <&pm8941_s3>;
+		startup-delay-us = <70000>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&lcd_backlight_en_pin_a>;
+	};
+
+	vreg_vsp: lcd-dcdc-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vreg_vsp";
+		regulator-min-microvolt = <5600000>;
+		regulator-max-microvolt = <5600000>;
+
+		gpio = <&pm8941_gpios 20 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&lcd_dcdc_en_pin_a>;
+	};
+
+	vreg_wlan: wlan-regulator {
+		compatible = "regulator-fixed";
+
+		regulator-name = "wl-reg";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&pm8941_gpios 18 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&wlan_regulator_pin>;
+	};
+};
+
+&blsp1_uart2 {
+	status = "okay";
+};
+
+&blsp2_i2c2 {
+	status = "okay";
+	clock-frequency = <355000>;
+
+	synaptics@2c {
+		compatible = "syna,rmi4-i2c";
+		reg = <0x2c>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <86 IRQ_TYPE_EDGE_FALLING>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		vdd-supply = <&pm8941_l22>;
+		vio-supply = <&pm8941_lvs3>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&ts_int_pin>;
+
+		syna,startup-delay-ms = <10>;
+
+		rmi-f01@1 {
+			reg = <0x1>;
+			syna,nosleep = <1>;
+		};
+
+		rmi-f11@11 {
+			reg = <0x11>;
+			syna,f11-flip-x = <1>;
+			syna,sensor-type = <1>;
+		};
+	};
+};
+
+&blsp2_i2c5 {
+	status = "okay";
+	clock-frequency = <355000>;
+
+	lp8566_wled: backlight@2c {
+		compatible = "ti,lp8556";
+		reg = <0x2c>;
+		power-supply = <&vreg_bl_vddio>;
+
+		bl-name = "backlight";
+		dev-ctrl = /bits/ 8 <0x05>;
+		init-brt = /bits/ 8 <0x3f>;
+		rom_a0h {
+			rom-addr = /bits/ 8 <0xa0>;
+			rom-val = /bits/ 8 <0xff>;
+		};
+		rom_a1h {
+			rom-addr = /bits/ 8 <0xa1>;
+			rom-val = /bits/ 8 <0x3f>;
+		};
+		rom_a2h {
+			rom-addr = /bits/ 8 <0xa2>;
+			rom-val = /bits/ 8 <0x20>;
+		};
+		rom_a3h {
+			rom-addr = /bits/ 8 <0xa3>;
+			rom-val = /bits/ 8 <0x5e>;
+		};
+		rom_a4h {
+			rom-addr = /bits/ 8 <0xa4>;
+			rom-val = /bits/ 8 <0x02>;
+		};
+		rom_a5h {
+			rom-addr = /bits/ 8 <0xa5>;
+			rom-val = /bits/ 8 <0x04>;
+		};
+		rom_a6h {
+			rom-addr = /bits/ 8 <0xa6>;
+			rom-val = /bits/ 8 <0x80>;
+		};
+		rom_a7h {
+			rom-addr = /bits/ 8 <0xa7>;
+			rom-val = /bits/ 8 <0xf7>;
+		};
+		rom_a9h {
+			rom-addr = /bits/ 8 <0xa9>;
+			rom-val = /bits/ 8 <0x80>;
+		};
+		rom_aah {
+			rom-addr = /bits/ 8 <0xaa>;
+			rom-val = /bits/ 8 <0x0f>;
+		};
+		rom_aeh {
+			rom-addr = /bits/ 8 <0xae>;
+			rom-val = /bits/ 8 <0x0f>;
+		};
+	};
+};
+
+&blsp2_uart1 {
+	status = "okay";
+
+	bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		max-speed = <3000000>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&bt_host_wake_pin>, <&bt_dev_wake_pin>, <&bt_reg_on_pin>;
+
+		host-wakeup-gpios = <&tlmm 95 GPIO_ACTIVE_HIGH>;
+		device-wakeup-gpios = <&tlmm 96 GPIO_ACTIVE_HIGH>;
+		shutdown-gpios = <&pm8941_gpios 16 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&otg {
+	status = "okay";
+
+	phys = <&usb_hs1_phy>;
+	phy-select = <&tcsr 0xb000 0>;
+	extcon = <&smbb>, <&usb_id>;
+	vbus-supply = <&chg_otg>;
+
+	hnp-disable;
+	srp-disable;
+	adp-disable;
+
+	ulpi {
+		phy@a {
+			status = "okay";
+
+			v1p8-supply = <&pm8941_l6>;
+			v3p3-supply = <&pm8941_l24>;
+
+			extcon = <&smbb>;
+			qcom,init-seq = /bits/ 8 <0x1 0x64>;
+		};
+	};
+};
+
+&pm8941_coincell {
+	status = "okay";
+
+	qcom,rset-ohms = <2100>;
+	qcom,vset-millivolts = <3000>;
+};
+
+&pm8941_gpios {
+	gpio_keys_pin_a: gpio-keys-active-state {
+		pins = "gpio2", "gpio5";
+		function = "normal";
+
+		bias-pull-up;
+		power-source = <PM8941_GPIO_S3>;
+	};
+
+	bt_reg_on_pin: bt-reg-on-state {
+		pins = "gpio16";
+		function = "normal";
+
+		output-low;
+		power-source = <PM8941_GPIO_S3>;
+	};
+
+	wlan_sleep_clk_pin: wl-sleep-clk-state {
+		pins = "gpio17";
+		function = "func2";
+
+		output-high;
+		power-source = <PM8941_GPIO_S3>;
+	};
+
+	wlan_regulator_pin: wl-reg-active-state {
+		pins = "gpio18";
+		function = "normal";
+
+		bias-disable;
+		power-source = <PM8941_GPIO_S3>;
+	};
+
+	lcd_dcdc_en_pin_a: lcd-dcdc-en-active-state {
+		pins = "gpio20";
+		function = "normal";
+
+		bias-disable;
+		power-source = <PM8941_GPIO_S3>;
+		input-disable;
+		output-low;
+	};
+
+};
+
+&pm8941_lpg {
+	status = "okay";
+
+	qcom,power-source = <1>;
+
+	rgb-led {
+		color = <LED_COLOR_ID_RGB>;
+		function = LED_FUNCTION_STATUS;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		led@5 {
+			reg = <5>;
+			color = <LED_COLOR_ID_BLUE>;
+		};
+
+		led@6 {
+			reg = <6>;
+			color = <LED_COLOR_ID_GREEN>;
+		};
+
+		led@7 {
+			reg = <7>;
+			color = <LED_COLOR_ID_RED>;
+		};
+	};
+};
+
+&rpm_requests {
+	pm8941-regulators {
+		compatible = "qcom,rpm-pm8941-regulators";
+
+		vdd_l1_l3-supply = <&pm8941_s1>;
+		vdd_l2_lvs1_2_3-supply = <&pm8941_s3>;
+		vdd_l4_l11-supply = <&pm8941_s1>;
+		vdd_l5_l7-supply = <&pm8941_s2>;
+		vdd_l6_l12_l14_l15-supply = <&pm8941_s2>;
+		vdd_l9_l10_l17_l22-supply = <&vreg_boost>;
+		vdd_l13_l20_l23_l24-supply = <&vreg_boost>;
+		vdd_l21-supply = <&vreg_boost>;
+
+		pm8941_s1: s1 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		pm8941_s2: s2 {
+			regulator-min-microvolt = <2150000>;
+			regulator-max-microvolt = <2150000>;
+			regulator-boot-on;
+		};
+
+		pm8941_s3: s3 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-system-load = <154000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		pm8941_s4: s4 {
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+		};
+
+		pm8941_l1: l1 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		pm8941_l2: l2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8941_l3: l3 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8941_l4: l4 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+		};
+
+		pm8941_l5: l5 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8941_l6: l6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-boot-on;
+		};
+
+		pm8941_l7: l7 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-boot-on;
+		};
+
+		pm8941_l8: l8 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8941_l9: l9 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8941_l11: l11 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1350000>;
+		};
+
+		pm8941_l12: l12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		pm8941_l13: l13 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-boot-on;
+		};
+
+		pm8941_l14: l14 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8941_l15: l15 {
+			regulator-min-microvolt = <2050000>;
+			regulator-max-microvolt = <2050000>;
+		};
+
+		pm8941_l16: l16 {
+			regulator-min-microvolt = <2700000>;
+			regulator-max-microvolt = <2700000>;
+		};
+
+		pm8941_l17: l17 {
+			regulator-min-microvolt = <2700000>;
+			regulator-max-microvolt = <2700000>;
+		};
+
+		pm8941_l18: l18 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+		};
+
+		pm8941_l19: l19 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+		};
+
+		pm8941_l20: l20 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-system-load = <500000>;
+			regulator-allow-set-load;
+			regulator-boot-on;
+		};
+
+		pm8941_l21: l21 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-boot-on;
+		};
+
+		pm8941_l22: l22 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+		};
+
+		pm8941_l23: l23 {
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+		};
+
+		pm8941_l24: l24 {
+			regulator-min-microvolt = <3075000>;
+			regulator-max-microvolt = <3075000>;
+			regulator-boot-on;
+		};
+
+		pm8941_lvs3: lvs3 {};
+	};
+};
+
+&sdhc_1 {
+	status = "okay";
+
+	vmmc-supply = <&pm8941_l20>;
+	vqmmc-supply = <&pm8941_s3>;
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sdc1_on>;
+	pinctrl-1 = <&sdc1_off>;
+};
+
+&sdhc_2 {
+	status = "okay";
+
+	vmmc-supply = <&pm8941_l21>;
+	vqmmc-supply = <&pm8941_l13>;
+
+	cd-gpios = <&tlmm 62 GPIO_ACTIVE_LOW>;
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sdc2_on>;
+	pinctrl-1 = <&sdc2_off>;
+};
+
+&sdhc_3 {
+	status = "okay";
+
+	max-frequency = <100000000>;
+	vmmc-supply = <&vreg_wlan>;
+	non-removable;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdc3_on>;
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	bcrmf@1 {
+		compatible = "brcm,bcm4339-fmac", "brcm,bcm4329-fmac";
+		reg = <1>;
+
+		brcm,drive-strength = <10>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&wlan_sleep_clk_pin>;
+	};
+};
+
+&smbb {
+	qcom,fast-charge-safe-current = <1500000>;
+	qcom,fast-charge-current-limit = <1500000>;
+	qcom,dc-current-limit = <1800000>;
+	qcom,fast-charge-safe-voltage = <4400000>;
+	qcom,fast-charge-high-threshold-voltage = <4350000>;
+	qcom,fast-charge-low-threshold-voltage = <3400000>;
+	qcom,auto-recharge-threshold-voltage = <4200000>;
+	qcom,minimum-input-voltage = <4300000>;
+};
+
+&tlmm {
+	lcd_backlight_en_pin_a: lcd-backlight-vddio {
+		pins = "gpio69";
+		drive-strength = <10>;
+		output-low;
+		bias-disable;
+	};
+
+	sdc1_on: sdc1-on {
+		clk {
+			pins = "sdc1_clk";
+			drive-strength = <16>;
+			bias-disable;
+		};
+
+		cmd-data {
+			pins = "sdc1_cmd", "sdc1_data";
+			drive-strength = <10>;
+			bias-pull-up;
+		};
+	};
+
+	sdc2_on: sdc2-on {
+		clk {
+			pins = "sdc2_clk";
+			drive-strength = <6>;
+			bias-disable;
+		};
+
+		cmd-data {
+			pins = "sdc2_cmd", "sdc2_data";
+			drive-strength = <6>;
+			bias-pull-up;
+		};
+
+		cd {
+			pins = "gpio62";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-disable;
+		};
+	};
+
+	sdc3_on: sdc3-on {
+		clk {
+			pins = "gpio40";
+			function = "sdc3";
+			drive-strength = <10>;
+			bias-disable;
+		};
+
+		cmd {
+			pins = "gpio39";
+			function = "sdc3";
+			drive-strength = <10>;
+			bias-pull-up;
+		};
+
+		data {
+			pins = "gpio35", "gpio36", "gpio37", "gpio38";
+			function = "sdc3";
+			drive-strength = <10>;
+			bias-pull-up;
+		};
+	};
+
+	ts_int_pin: ts-int-pin {
+		pins = "gpio86";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+		input-enable;
+	};
+
+	bt_host_wake_pin: bt-host-wake {
+		pins = "gpio95";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+		output-low;
+	};
+
+	bt_dev_wake_pin: bt-dev-wake {
+		pins = "gpio96";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+};
diff --git a/arch/arm/boot/dts/qcom-msm8974pro.dtsi b/arch/arm/boot/dts/qcom-msm8974pro.dtsi
index b64c28036dd0..58df6e75ab6d 100644
--- a/arch/arm/boot/dts/qcom-msm8974pro.dtsi
+++ b/arch/arm/boot/dts/qcom-msm8974pro.dtsi
@@ -1,23 +1,19 @@
+// SPDX-License-Identifier: GPL-2.0
 #include "qcom-msm8974.dtsi"
 
-/ {
-	soc {
-		sdhci@f9824900 {
-			clocks = <&gcc GCC_SDCC1_APPS_CLK>,
-				 <&gcc GCC_SDCC1_AHB_CLK>,
-				 <&xo_board>,
-				 <&gcc GCC_SDCC1_CDCCAL_FF_CLK>,
-				 <&gcc GCC_SDCC1_CDCCAL_SLEEP_CLK>;
-			clock-names = "core", "iface", "xo", "cal", "sleep";
-		};
+&gcc {
+	compatible = "qcom,gcc-msm8974pro";
+};
 
-		clock-controller@fc400000 {
-				compatible = "qcom,gcc-msm8974pro";
-		};
+&gpu {
+	compatible = "qcom,adreno-330.2", "qcom,adreno";
+};
 
-		adreno@fdb00000 {
-			compatible = "qcom,adreno-330.2",
-				     "qcom,adreno";
-		};
-	};
+&sdhc_1 {
+	clocks = <&gcc GCC_SDCC1_AHB_CLK>,
+		 <&gcc GCC_SDCC1_APPS_CLK>,
+		 <&xo_board>,
+		 <&gcc GCC_SDCC1_CDCCAL_FF_CLK>,
+		 <&gcc GCC_SDCC1_CDCCAL_SLEEP_CLK>;
+	clock-names = "iface", "core", "xo", "cal", "sleep";
 };
diff --git a/arch/arm/boot/dts/qcom-pm8226.dtsi b/arch/arm/boot/dts/qcom-pm8226.dtsi
index dddb5150dfd7..9b7d9d04ded6 100644
--- a/arch/arm/boot/dts/qcom-pm8226.dtsi
+++ b/arch/arm/boot/dts/qcom-pm8226.dtsi
@@ -1,6 +1,7 @@
 // SPDX-License-Identifier: BSD-3-Clause
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/spmi/spmi.h>
+#include <dt-bindings/iio/qcom,spmi-vadc.h>
 
 &spmi_bus {
 	pm8226_0: pm8226@0 {
@@ -16,6 +17,79 @@
 			debounce = <15625>;
 			bias-pull-up;
 		};
+
+		smbb: charger@1000 {
+			compatible = "qcom,pm8226-charger";
+			reg = <0x1000>;
+			interrupts = <0x0 0x10 7 IRQ_TYPE_EDGE_BOTH>,
+				     <0x0 0x10 5 IRQ_TYPE_EDGE_BOTH>,
+				     <0x0 0x10 4 IRQ_TYPE_EDGE_BOTH>,
+				     <0x0 0x12 1 IRQ_TYPE_EDGE_BOTH>,
+				     <0x0 0x12 0 IRQ_TYPE_EDGE_BOTH>,
+				     <0x0 0x13 2 IRQ_TYPE_EDGE_BOTH>,
+				     <0x0 0x13 1 IRQ_TYPE_EDGE_BOTH>,
+				     <0x0 0x14 1 IRQ_TYPE_EDGE_BOTH>;
+			interrupt-names = "chg-done",
+					  "chg-fast",
+					  "chg-trkl",
+					  "bat-temp-ok",
+					  "bat-present",
+					  "chg-gone",
+					  "usb-valid",
+					  "dc-valid";
+
+			chg_otg: otg-vbus { };
+		};
+
+		rtc@6000 {
+			compatible = "qcom,pm8941-rtc";
+			reg = <0x6000>, <0x6100>;
+			reg-names = "rtc", "alarm";
+			interrupts = <0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>;
+		};
+
+		pm8226_vadc: adc@3100 {
+			compatible = "qcom,spmi-vadc";
+			reg = <0x3100>;
+			interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			#io-channel-cells = <1>;
+
+			adc-chan@7 {
+				reg = <VADC_VSYS>;
+				qcom,pre-scaling = <1 3>;
+				label = "vph_pwr";
+			};
+			adc-chan@8 {
+				reg = <VADC_DIE_TEMP>;
+				label = "die_temp";
+			};
+			adc-chan@9 {
+				reg = <VADC_REF_625MV>;
+				label = "ref_625mv";
+			};
+			adc-chan@a {
+				reg = <VADC_REF_1250MV>;
+				label = "ref_1250mv";
+			};
+			adc-chan@e {
+				reg = <VADC_GND_REF>;
+			};
+			adc-chan@f {
+				reg = <VADC_VDD_VADC>;
+			};
+		};
+
+		pm8226_mpps: mpps@a000 {
+			compatible = "qcom,pm8226-mpp", "qcom,spmi-mpp";
+			reg = <0xa000>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&pm8226_mpps 0 0 8>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
 	};
 
 	pm8226_1: pm8226@1 {
@@ -23,5 +97,15 @@
 		reg = <0x1 SPMI_USID>;
 		#address-cells = <1>;
 		#size-cells = <0>;
+
+		pm8226_spmi_regulators: pm8226-regulators {
+			compatible = "qcom,pm8226-regulators";
+		};
+
+		pm8226_vib: vibrator@c000 {
+			compatible = "qcom,pm8916-vib";
+			reg = <0xc000>;
+			status = "disabled";
+		};
 	};
 };
diff --git a/arch/arm/boot/dts/qcom-pm8841.dtsi b/arch/arm/boot/dts/qcom-pm8841.dtsi
index 2caf71eacb52..b5cdde034d18 100644
--- a/arch/arm/boot/dts/qcom-pm8841.dtsi
+++ b/arch/arm/boot/dts/qcom-pm8841.dtsi
@@ -24,6 +24,7 @@
 			compatible = "qcom,spmi-temp-alarm";
 			reg = <0x2400>;
 			interrupts = <4 0x24 0 IRQ_TYPE_EDGE_RISING>;
+			#thermal-sensor-cells = <0>;
 		};
 	};
 
diff --git a/arch/arm/boot/dts/qcom-pm8941.dtsi b/arch/arm/boot/dts/qcom-pm8941.dtsi
index da00b8f5eecd..9cd49deb9fa7 100644
--- a/arch/arm/boot/dts/qcom-pm8941.dtsi
+++ b/arch/arm/boot/dts/qcom-pm8941.dtsi
@@ -68,7 +68,7 @@
 			interrupt-controller;
 			#interrupt-cells = <2>;
 
-			boost_bypass_n_pin: boost-bypass {
+			boost_bypass_n_pin: boost-bypass-state {
 				pins = "gpio21";
 				function = "normal";
 			};
@@ -93,7 +93,7 @@
 			#thermal-sensor-cells = <0>;
 		};
 
-		pm8941_vadc: vadc@3100 {
+		pm8941_vadc: adc@3100 {
 			compatible = "qcom,spmi-vadc";
 			reg = <0x3100>;
 			interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
@@ -131,7 +131,7 @@
 			qcom,external-resistor-micro-ohms = <10000>;
 		};
 
-		coincell@2800 {
+		pm8941_coincell: coincell@2800 {
 			compatible = "qcom,pm8941-coincell";
 			reg = <0x2800>;
 			status = "disabled";
@@ -144,6 +144,16 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
+		pm8941_lpg: pwm {
+			compatible = "qcom,pm8941-lpg";
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+			#pwm-cells = <2>;
+
+			status = "disabled";
+		};
+
 		pm8941_wled: wled@d800 {
 			compatible = "qcom,pm8941-wled";
 			reg = <0xd800>;
diff --git a/arch/arm/boot/dts/qcom-pma8084.dtsi b/arch/arm/boot/dts/qcom-pma8084.dtsi
index 7b8a8d9695da..e77602e9f95c 100644
--- a/arch/arm/boot/dts/qcom-pma8084.dtsi
+++ b/arch/arm/boot/dts/qcom-pma8084.dtsi
@@ -56,7 +56,7 @@
 			io-channel-names = "thermal";
 		};
 
-		pma8084_vadc: vadc@3100 {
+		pma8084_vadc: adc@3100 {
 			compatible = "qcom,spmi-vadc";
 			reg = <0x3100>;
 			interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
diff --git a/arch/arm/boot/dts/qcom-pmx55.dtsi b/arch/arm/boot/dts/qcom-pmx55.dtsi
index 6571b88d018a..e1b869480bbd 100644
--- a/arch/arm/boot/dts/qcom-pmx55.dtsi
+++ b/arch/arm/boot/dts/qcom-pmx55.dtsi
@@ -16,7 +16,7 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		power-on@800 {
+		pon@800 {
 			compatible = "qcom,pm8916-pon";
 			reg = <0x0800>;
 
@@ -69,6 +69,7 @@
 			compatible = "qcom,pmx55-gpio", "qcom,spmi-gpio";
 			reg = <0xc000>;
 			gpio-controller;
+			gpio-ranges = <&pmx55_gpios 0 0 11>;
 			#gpio-cells = <2>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
diff --git a/arch/arm/boot/dts/qcom-pmx65.dtsi b/arch/arm/boot/dts/qcom-pmx65.dtsi
new file mode 100644
index 000000000000..abf229a8b75a
--- /dev/null
+++ b/arch/arm/boot/dts/qcom-pmx65.dtsi
@@ -0,0 +1,33 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (c) 2022, Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/spmi/spmi.h>
+
+&spmi_bus {
+	pmic@1 {
+		compatible = "qcom,pmx65", "qcom,spmi-pmic";
+		reg = <1 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pmx65_temp: temp-alarm@a00 {
+			compatible = "qcom,spmi-temp-alarm";
+			reg = <0xa00>;
+			interrupts = <0x1 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
+			#thermal-sensor-cells = <0>;
+		};
+
+		pmx65_gpios: pinctrl@8800 {
+			compatible = "qcom,pmx65-gpio", "qcom,spmi-gpio";
+			reg = <0x8800>;
+			gpio-controller;
+			gpio-ranges = <&pmx65_gpios 0 0 16>;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/qcom-sdx55-t55.dts b/arch/arm/boot/dts/qcom-sdx55-t55.dts
index 2ffcd085904d..7ed8feb99afb 100644
--- a/arch/arm/boot/dts/qcom-sdx55-t55.dts
+++ b/arch/arm/boot/dts/qcom-sdx55-t55.dts
@@ -236,6 +236,12 @@
 	status = "ok";
 };
 
+&ipa {
+	status = "okay";
+
+	memory-region = <&ipa_fw_mem>;
+};
+
 &qpic_bam {
 	status = "ok";
 };
diff --git a/arch/arm/boot/dts/qcom-sdx55-telit-fn980-tlb.dts b/arch/arm/boot/dts/qcom-sdx55-telit-fn980-tlb.dts
index 80c40da79604..a4fa468a095f 100644
--- a/arch/arm/boot/dts/qcom-sdx55-telit-fn980-tlb.dts
+++ b/arch/arm/boot/dts/qcom-sdx55-telit-fn980-tlb.dts
@@ -236,6 +236,27 @@
 	status = "ok";
 };
 
+&ipa {
+	status = "okay";
+
+	memory-region = <&ipa_fw_mem>;
+};
+
+&pcie0_phy {
+	status = "okay";
+
+	vdda-phy-supply = <&vreg_l1e_bb_1p2>;
+	vdda-pll-supply = <&vreg_l4e_bb_0p875>;
+};
+
+&pcie_ep {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie_ep_clkreq_default &pcie_ep_perst_default
+		     &pcie_ep_wake_default>;
+};
+
 &qpic_bam {
 	status = "ok";
 };
@@ -260,6 +281,44 @@
 	memory-region = <&mpss_adsp_mem>;
 };
 
+&tlmm {
+	pcie_ep_clkreq_default: pcie_ep_clkreq_default {
+		mux {
+			pins = "gpio56";
+			function = "pcie_clkreq";
+		};
+		config {
+			pins = "gpio56";
+			drive-strength = <2>;
+			bias-disable;
+		};
+	};
+
+	pcie_ep_perst_default: pcie_ep_perst_default {
+		mux {
+			pins = "gpio57";
+			function = "gpio";
+		};
+		config {
+			pins = "gpio57";
+			drive-strength = <2>;
+			bias-pull-down;
+		};
+	};
+
+	pcie_ep_wake_default: pcie_ep_wake_default {
+		mux {
+			pins = "gpio53";
+			function = "gpio";
+		};
+		config {
+			pins = "gpio53";
+			drive-strength = <2>;
+			bias-disable;
+		};
+	};
+};
+
 &usb_hsphy {
 	status = "okay";
 	vdda-pll-supply = <&vreg_l4e_bb_0p875>;
diff --git a/arch/arm/boot/dts/qcom-sdx55.dtsi b/arch/arm/boot/dts/qcom-sdx55.dtsi
index 44526ad9d210..c72540223fa9 100644
--- a/arch/arm/boot/dts/qcom-sdx55.dtsi
+++ b/arch/arm/boot/dts/qcom-sdx55.dtsi
@@ -8,6 +8,7 @@
 
 #include <dt-bindings/clock/qcom,gcc-sdx55.h>
 #include <dt-bindings/clock/qcom,rpmh.h>
+#include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/interconnect/qcom,sdx55.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/power/qcom-rpmpd.h>
@@ -205,7 +206,7 @@
 		blsp1_uart3: serial@831000 {
 			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
 			reg = <0x00831000 0x200>;
-			interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_LOW>;
+			interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&gcc 30>,
 				 <&gcc 9>;
 			clock-names = "core", "iface";
@@ -274,13 +275,6 @@
 			qcom,bcm-voters = <&apps_bcm_voter>;
 		};
 
-		ipa_virt: interconnect@1e00000 {
-			compatible = "qcom,sdx55-ipa-virt";
-			reg = <0x01e00000 0x100000>;
-			#interconnect-cells = <1>;
-			qcom,bcm-voters = <&apps_bcm_voter>;
-		};
-
 		qpic_bam: dma-controller@1b04000 {
 			compatible = "qcom,bam-v1.7.0";
 			reg = <0x01b04000 0x1c000>;
@@ -309,6 +303,41 @@
 			status = "disabled";
 		};
 
+		pcie0_phy: phy@1c07000 {
+			compatible = "qcom,sdx55-qmp-pcie-phy";
+			reg = <0x01c07000 0x1c4>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			clocks = <&gcc GCC_PCIE_AUX_PHY_CLK_SRC>,
+				 <&gcc GCC_PCIE_CFG_AHB_CLK>,
+				 <&gcc GCC_PCIE_0_CLKREF_CLK>,
+				 <&gcc GCC_PCIE_RCHNG_PHY_CLK>;
+			clock-names = "aux", "cfg_ahb", "ref", "refgen";
+
+			resets = <&gcc GCC_PCIE_PHY_BCR>;
+			reset-names = "phy";
+
+			assigned-clocks = <&gcc GCC_PCIE_RCHNG_PHY_CLK>;
+			assigned-clock-rates = <100000000>;
+
+			status = "disabled";
+
+			pcie0_lane: lanes@1c06000 {
+				reg = <0x01c06000 0x104>, /* tx0 */
+				      <0x01c06200 0x328>, /* rx0 */
+				      <0x01c07200 0x1e8>, /* pcs */
+				      <0x01c06800 0x104>, /* tx1 */
+				      <0x01c06a00 0x328>, /* rx1 */
+				      <0x01c07600 0x800>; /* pcs_misc */
+				clocks = <&gcc GCC_PCIE_PIPE_CLK>;
+				clock-names = "pipe0";
+
+				#phy-cells = <0>;
+				clock-output-names = "pcie_pipe_clk";
+			};
+		};
+
 		ipa: ipa@1e40000 {
 			compatible = "qcom,sdx55-ipa";
 
@@ -333,12 +362,10 @@
 			clocks = <&rpmhcc RPMH_IPA_CLK>;
 			clock-names = "core";
 
-			interconnects = <&system_noc MASTER_IPA &system_noc SLAVE_SNOC_MEM_NOC_GC>,
-					<&mem_noc MASTER_SNOC_GC_MEM_NOC &mc_virt SLAVE_EBI_CH0>,
+			interconnects = <&system_noc MASTER_IPA &mc_virt SLAVE_EBI_CH0>,
 					<&system_noc MASTER_IPA &system_noc SLAVE_OCIMEM>,
 					<&mem_noc MASTER_AMPSS_M0 &system_noc SLAVE_IPA_CFG>;
-			interconnect-names = "memory-a",
-					     "memory-b",
+			interconnect-names = "memory",
 					     "imem",
 					     "config";
 
@@ -356,7 +383,12 @@
 			#hwlock-cells = <1>;
 		};
 
-		sdhc_1: sdhci@8804000 {
+		tcsr: syscon@1fcb000 {
+			compatible = "syscon";
+			reg = <0x01fc0000 0x1000>;
+		};
+
+		sdhc_1: mmc@8804000 {
 			compatible = "qcom,sdx55-sdhci", "qcom,sdhci-msm-v5";
 			reg = <0x08804000 0x1000>;
 			interrupts = <GIC_SPI 210 IRQ_TYPE_LEVEL_HIGH>,
@@ -368,6 +400,45 @@
 			status = "disabled";
 		};
 
+		pcie_ep: pcie-ep@40000000 {
+			compatible = "qcom,sdx55-pcie-ep";
+			reg = <0x01c00000 0x3000>,
+			      <0x40000000 0xf1d>,
+			      <0x40000f20 0xc8>,
+			      <0x40001000 0x1000>,
+			      <0x40200000 0x100000>,
+			      <0x01c03000 0x3000>;
+			reg-names = "parf", "dbi", "elbi", "atu", "addr_space",
+				    "mmio";
+
+			qcom,perst-regs = <&tcsr 0xb258 0xb270>;
+
+			clocks = <&gcc GCC_PCIE_AUX_CLK>,
+				 <&gcc GCC_PCIE_CFG_AHB_CLK>,
+				 <&gcc GCC_PCIE_MSTR_AXI_CLK>,
+				 <&gcc GCC_PCIE_SLV_AXI_CLK>,
+				 <&gcc GCC_PCIE_SLV_Q2A_AXI_CLK>,
+				 <&gcc GCC_PCIE_SLEEP_CLK>,
+				 <&gcc GCC_PCIE_0_CLKREF_CLK>;
+			clock-names = "aux", "cfg", "bus_master", "bus_slave",
+				      "slave_q2a", "sleep", "ref";
+
+			interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "global", "doorbell";
+			reset-gpios = <&tlmm 57 GPIO_ACTIVE_LOW>;
+			wake-gpios = <&tlmm 53 GPIO_ACTIVE_LOW>;
+			resets = <&gcc GCC_PCIE_BCR>;
+			reset-names = "core";
+			power-domains = <&gcc PCIE_GDSC>;
+			phys = <&pcie0_lane>;
+			phy-names = "pciephy";
+			max-link-speed = <3>;
+			num-lanes = <2>;
+
+			status = "disabled";
+		};
+
 		remoteproc_mpss: remoteproc@4080000 {
 			compatible = "qcom,sdx55-mpss-pas";
 			reg = <0x04080000 0x4040>;
@@ -412,10 +483,13 @@
 			clocks = <&gcc GCC_USB30_SLV_AHB_CLK>,
 				 <&gcc GCC_USB30_MASTER_CLK>,
 				 <&gcc GCC_USB30_MSTR_AXI_CLK>,
-				 <&gcc GCC_USB30_MOCK_UTMI_CLK>,
-				 <&gcc GCC_USB30_SLEEP_CLK>;
-			clock-names = "cfg_noc", "core", "iface", "mock_utmi",
-				      "sleep";
+				 <&gcc GCC_USB30_SLEEP_CLK>,
+				 <&gcc GCC_USB30_MOCK_UTMI_CLK>;
+			clock-names = "cfg_noc",
+				      "core",
+				      "iface",
+				      "sleep",
+				      "mock_utmi";
 
 			assigned-clocks = <&gcc GCC_USB30_MOCK_UTMI_CLK>,
 					  <&gcc GCC_USB30_MASTER_CLK>;
@@ -458,7 +532,7 @@
 			reg = <0x0c264000 0x1000>;
 		};
 
-		spmi_bus: qcom,spmi@c440000 {
+		spmi_bus: spmi@c440000 {
 			compatible = "qcom,spmi-pmic-arb";
 			reg = <0x0c440000 0x0000d00>,
 			      <0x0c600000 0x2000000>,
@@ -487,8 +561,8 @@
 			#interrupt-cells = <2>;
 		};
 
-		imem@1468f000 {
-			compatible = "simple-mfd";
+		sram@1468f000 {
+			compatible = "qcom,sdx55-imem", "syscon", "simple-mfd";
 			reg = <0x1468f000 0x1000>;
 
 			#address-cells = <1>;
@@ -692,7 +766,7 @@
 				};
 			};
 
-			apps_bcm_voter: bcm_voter {
+			apps_bcm_voter: bcm-voter {
 				compatible = "qcom,bcm-voter";
 			};
 		};
diff --git a/arch/arm/boot/dts/qcom-sdx65-mtp.dts b/arch/arm/boot/dts/qcom-sdx65-mtp.dts
new file mode 100644
index 000000000000..85ea02d8362d
--- /dev/null
+++ b/arch/arm/boot/dts/qcom-sdx65-mtp.dts
@@ -0,0 +1,291 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+/dts-v1/;
+
+#include "qcom-sdx65.dtsi"
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+#include <arm64/qcom/pmk8350.dtsi>
+#include <arm64/qcom/pm8150b.dtsi>
+#include "qcom-pmx65.dtsi"
+
+/ {
+	model = "Qualcomm Technologies, Inc. SDX65 MTP";
+	compatible = "qcom,sdx65-mtp", "qcom,sdx65";
+	qcom,board-id = <0x2010008 0x302>;
+
+	aliases {
+		serial0 = &blsp1_uart3;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		mpss_dsm: memory@8c400000 {
+			no-map;
+			reg = <0x8c400000 0x3200000>;
+		};
+
+		ipa_fw_mem: memory@8fced000 {
+			no-map;
+			reg = <0x8fced000 0x10000>;
+		};
+
+		mpss_adsp_mem: memory@90800000 {
+			no-map;
+			reg = <0x90800000 0x10000000>;
+		};
+	};
+
+	vph_pwr: vph-pwr-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vph_pwr";
+		regulator-min-microvolt = <3700000>;
+		regulator-max-microvolt = <3700000>;
+	};
+
+	vreg_bob_3p3: pmx65_bob {
+		compatible = "regulator-fixed";
+		regulator-name = "vreg_bob_3p3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		regulator-always-on;
+		regulator-boot-on;
+
+		vin-supply = <&vph_pwr>;
+	};
+};
+
+&apps_rsc {
+	pmx65-rpmh-regulators {
+		compatible = "qcom,pmx65-rpmh-regulators";
+		qcom,pmic-id = "b";
+
+		vdd-s1-supply = <&vph_pwr>;
+		vdd-s2-supply = <&vph_pwr>;
+		vdd-s3-supply = <&vph_pwr>;
+		vdd-s4-supply = <&vph_pwr>;
+		vdd-s5-supply = <&vph_pwr>;
+		vdd-s6-supply = <&vph_pwr>;
+		vdd-s7-supply = <&vph_pwr>;
+		vdd-s8-supply = <&vph_pwr>;
+		vdd-l1-supply = <&vreg_s2b_1p224>;
+		vdd-l2-l18-supply = <&vreg_s2b_1p224>;
+		vdd-l3-supply = <&vreg_s8b_0p824>;
+		vdd-l4-supply = <&vreg_s7b_0p936>;
+		vdd-l5-l6-l16-supply = <&vreg_s4b_1p824>;
+		vdd-l7-supply = <&vreg_s3b_0p776>;
+		vdd-l8-l9-supply = <&vreg_s8b_0p824>;
+		vdd-l10-supply = <&vreg_bob_3p3>;
+		vdd-l11-l13-supply = <&vreg_bob_3p3>;
+		vdd-l12-supply = <&vreg_s2b_1p224>;
+		vdd-l14-supply = <&vreg_s3b_0p776>;
+		vdd-l15-supply = <&vreg_s2b_1p224>;
+		vdd-l17-supply = <&vreg_s8b_0p824>;
+		vdd-l19-supply = <&vreg_s3b_0p776>;
+		vdd-l20-supply = <&vreg_s7b_0p936>;
+		vdd-l21-supply = <&vreg_s7b_0p936>;
+
+		vreg_s2b_1p224: smps2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1400000>;
+		};
+
+		vreg_s3b_0p776: smps3 {
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1040000>;
+		};
+
+		vreg_s4b_1p824: smps4 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2024000>;
+		};
+
+		vreg_s7b_0p936: smps7 {
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1040000>;
+		};
+
+		vreg_s8b_0p824: smps8 {
+			regulator-min-microvolt = <304000>;
+			regulator-max-microvolt = <1300000>;
+		};
+
+		vreg_l1b_1p2: ldo1 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		ldo2 {
+			regulator-min-microvolt = <1128000>;
+			regulator-max-microvolt = <1128000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		ldo3 {
+			regulator-min-microvolt = <300000>;
+			regulator-max-microvolt = <960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l4b_0p88: ldo4 {
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l5b_1p8: ldo5 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		ldo6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		ldo7 {
+			regulator-min-microvolt = <752000>;
+			regulator-max-microvolt = <752000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		ldo8 {
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		ldo9 {
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l10b_3p08: ldo10 {
+			regulator-min-microvolt = <3088000>;
+			regulator-max-microvolt = <3088000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		ldo11 {
+			regulator-min-microvolt = <1704000>;
+			regulator-max-microvolt = <2928000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		ldo12 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		ldo13 {
+			regulator-min-microvolt = <1704000>;
+			regulator-max-microvolt = <2928000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		ldo14 {
+			regulator-min-microvolt = <600000>;
+			regulator-max-microvolt = <800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		ldo15 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		ldo16 {
+			regulator-min-microvolt = <1776000>;
+			regulator-max-microvolt = <1776000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		ldo17 {
+			regulator-min-microvolt = <300000>;
+			regulator-max-microvolt = <960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		ldo19 {
+			regulator-min-microvolt = <752000>;
+			regulator-max-microvolt = <752000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		ldo20 {
+			regulator-min-microvolt = <912000>;
+			regulator-max-microvolt = <912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		ldo21 {
+			regulator-min-microvolt = <912000>;
+			regulator-max-microvolt = <912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+};
+
+&blsp1_uart3 {
+	status = "okay";
+};
+
+&qpic_bam {
+	status = "okay";
+};
+
+&qpic_nand {
+	status = "okay";
+
+	nand@0 {
+		reg = <0>;
+
+		nand-ecc-strength = <4>;
+		nand-ecc-step-size = <512>;
+		nand-bus-width = <8>;
+		/* ico and efs2 partitions are secured */
+		secure-regions = /bits/ 64 <0x500000 0x500000
+					    0xa00000 0xb00000>;
+	};
+};
+
+&remoteproc_mpss {
+	status = "okay";
+	memory-region = <&mpss_adsp_mem>;
+};
+
+&usb {
+	status = "okay";
+};
+
+&usb_dwc3 {
+	dr_mode = "peripheral";
+};
+
+&usb_hsphy {
+	status = "okay";
+	vdda-pll-supply = <&vreg_l4b_0p88>;
+	vdda33-supply = <&vreg_l10b_3p08>;
+	vdda18-supply = <&vreg_l5b_1p8>;
+};
+
+&usb_qmpphy {
+	status = "okay";
+	vdda-phy-supply = <&vreg_l4b_0p88>;
+	vdda-pll-supply = <&vreg_l1b_1p2>;
+};
diff --git a/arch/arm/boot/dts/qcom-sdx65.dtsi b/arch/arm/boot/dts/qcom-sdx65.dtsi
new file mode 100644
index 000000000000..4cd405db5500
--- /dev/null
+++ b/arch/arm/boot/dts/qcom-sdx65.dtsi
@@ -0,0 +1,682 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * SDX65 SoC device tree source
+ *
+ * Copyright (c) 2021 Qualcomm Innovation Center, Inc. All rights reserved.
+ *
+ */
+
+#include <dt-bindings/clock/qcom,gcc-sdx65.h>
+#include <dt-bindings/clock/qcom,rpmh.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/power/qcom-rpmpd.h>
+#include <dt-bindings/soc/qcom,rpmh-rsc.h>
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	qcom,msm-id = <458 0x10000>, <483 0x10000>, <509 0x10000>;
+	interrupt-parent = <&intc>;
+
+	memory {
+		device_type = "memory";
+		reg = <0 0>;
+	};
+
+	clocks {
+		xo_board: xo-board {
+			compatible = "fixed-clock";
+			clock-frequency = <76800000>;
+			clock-output-names = "xo_board";
+			#clock-cells = <0>;
+		};
+
+		sleep_clk: sleep-clk {
+			compatible = "fixed-clock";
+			clock-frequency = <32764>;
+			clock-output-names = "sleep_clk";
+			#clock-cells = <0>;
+		};
+
+		nand_clk_dummy: nand-clk-dummy {
+			compatible = "fixed-clock";
+			clock-frequency = <32764>;
+			#clock-cells = <0>;
+		};
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a7";
+			reg = <0x0>;
+			enable-method = "psci";
+			clocks = <&apcs>;
+			power-domains = <&rpmhpd SDX65_CX_AO>;
+			power-domain-names = "rpmhpd";
+			operating-points-v2 = <&cpu_opp_table>;
+		};
+	};
+
+	cpu_opp_table: cpu-opp-table {
+		compatible = "operating-points-v2";
+		opp-shared;
+
+		opp-345600000 {
+			opp-hz = /bits/ 64 <345600000>;
+			required-opps = <&rpmhpd_opp_low_svs>;
+		};
+
+		opp-576000000 {
+			opp-hz = /bits/ 64 <576000000>;
+			required-opps = <&rpmhpd_opp_svs>;
+		};
+
+		opp-1094400000 {
+			opp-hz = /bits/ 64 <1094400000>;
+			required-opps = <&rpmhpd_opp_nom>;
+		};
+
+		opp-1497600000 {
+			opp-hz = /bits/ 64 <1497600000>;
+			required-opps = <&rpmhpd_opp_turbo>;
+		};
+	};
+
+	firmware {
+		scm {
+			compatible = "qcom,scm-sdx65", "qcom,scm";
+		};
+	};
+
+	mc_virt: interconnect-mc-virt {
+		compatible = "qcom,sdx65-mc-virt";
+		#interconnect-cells = <1>;
+		qcom,bcm-voters = <&apps_bcm_voter>;
+	};
+
+	psci {
+		compatible = "arm,psci-1.0";
+		method = "smc";
+	};
+
+	reserved_memory: reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		tz_heap_mem: memory@8fcad000 {
+			no-map;
+			reg = <0x8fcad000 0x40000>;
+		};
+
+		secdata_mem: memory@8fcfd000 {
+			no-map;
+			reg = <0x8fcfd000 0x1000>;
+		};
+
+		hyp_mem: memory@8fd00000 {
+			no-map;
+			reg = <0x8fd00000 0x80000>;
+		};
+
+		access_control_mem: memory@8fd80000 {
+			no-map;
+			reg = <0x8fd80000 0x80000>;
+		};
+
+		aop_mem: memory@8fe00000 {
+			no-map;
+			reg = <0x8fe00000 0x20000>;
+		};
+
+		smem_mem: memory@8fe20000 {
+			compatible = "qcom,smem";
+			reg = <0x8fe20000 0xc0000>;
+			hwlocks = <&tcsr_mutex 3>;
+			no-map;
+		};
+
+		cmd_db: reserved-memory@8fee0000 {
+			compatible = "qcom,cmd-db";
+			reg = <0x8fee0000 0x20000>;
+			no-map;
+		};
+
+		tz_mem: memory@8ff00000 {
+			no-map;
+			reg = <0x8ff00000 0x100000>;
+		};
+
+		tz_apps_mem: memory@90000000 {
+			no-map;
+			reg = <0x90000000 0x500000>;
+		};
+
+		llcc_tcm_mem: memory@15800000 {
+			no-map;
+			reg = <0x15800000 0x800000>;
+		};
+	};
+
+	smp2p-mpss {
+		compatible = "qcom,smp2p";
+		qcom,smem = <435>, <428>;
+		interrupts = <GIC_SPI 113 IRQ_TYPE_EDGE_RISING>;
+		mboxes = <&apcs 14>;
+		qcom,local-pid = <0>;
+		qcom,remote-pid = <1>;
+
+		modem_smp2p_out: master-kernel {
+			qcom,entry-name = "master-kernel";
+			#qcom,smem-state-cells = <1>;
+		};
+
+		modem_smp2p_in: slave-kernel {
+			qcom,entry-name = "slave-kernel";
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		ipa_smp2p_out: ipa-ap-to-modem {
+			qcom,entry-name = "ipa";
+			#qcom,smem-state-cells = <1>;
+		};
+
+		ipa_smp2p_in: ipa-modem-to-ap {
+			qcom,entry-name = "ipa";
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	soc: soc {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+		compatible = "simple-bus";
+
+		gcc: clock-controller@100000 {
+			compatible = "qcom,gcc-sdx65";
+			reg = <0x00100000 0x001f7400>;
+			clocks = <&rpmhcc RPMH_CXO_CLK>, <&rpmhcc RPMH_CXO_CLK_A>, <&sleep_clk>;
+			clock-names = "bi_tcxo", "bi_tcxo_ao", "sleep_clk";
+			#power-domain-cells = <1>;
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+		};
+
+		blsp1_uart3: serial@831000 {
+			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+			reg = <0x00831000 0x200>;
+			interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_UART3_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			status = "disabled";
+		};
+
+		usb_hsphy: phy@ff4000 {
+			compatible = "qcom,usb-snps-hs-7nm-phy";
+			reg = <0xff4000 0x120>;
+			#phy-cells = <0>;
+			status = "disabled";
+			clocks = <&rpmhcc RPMH_CXO_CLK>;
+			clock-names = "ref";
+			resets = <&gcc GCC_QUSB2PHY_BCR>;
+		};
+
+		usb_qmpphy: phy@ff6000 {
+			compatible = "qcom,sdx65-qmp-usb3-uni-phy";
+			reg = <0x00ff6000 0x1c8>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			clocks = <&gcc GCC_USB3_PHY_AUX_CLK>,
+				 <&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>,
+				 <&gcc GCC_USB3_PRIM_CLKREF_EN>;
+			clock-names = "aux", "cfg_ahb", "ref";
+
+			resets = <&gcc GCC_USB3PHY_PHY_BCR>,
+				 <&gcc GCC_USB3_PHY_BCR>;
+			reset-names = "phy", "common";
+
+			usb_ssphy: phy@ff6200 {
+				reg = <0x00ff6e00 0x160>,
+				      <0x00ff7000 0x1ec>,
+				      <0x00ff6200 0x1e00>;
+				#phy-cells = <0>;
+				#clock-cells = <0>;
+				clocks = <&gcc GCC_USB3_PHY_PIPE_CLK>;
+				clock-names = "pipe0";
+				clock-output-names = "usb3_uni_phy_pipe_clk_src";
+			};
+		};
+
+		system_noc: interconnect@1620000 {
+			compatible = "qcom,sdx65-system-noc";
+			reg = <0x01620000 0x31200>;
+			#interconnect-cells = <1>;
+			qcom,bcm-voters = <&apps_bcm_voter>;
+		};
+
+		qpic_bam: dma-controller@1b04000 {
+			compatible = "qcom,bam-v1.7.0";
+			reg = <0x01b04000 0x1c000>;
+			interrupts = <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rpmhcc RPMH_QPIC_CLK>;
+			clock-names = "bam_clk";
+			#dma-cells = <1>;
+			qcom,ee = <0>;
+			qcom,controlled-remotely;
+			status = "disabled";
+		};
+
+		qpic_nand: nand-controller@1b30000 {
+			compatible = "qcom,sdx55-nand";
+			reg = <0x01b30000 0x10000>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			clocks = <&rpmhcc RPMH_QPIC_CLK>,
+				 <&nand_clk_dummy>;
+			clock-names = "core", "aon";
+
+			dmas = <&qpic_bam 0>,
+			       <&qpic_bam 1>,
+			       <&qpic_bam 2>;
+			dma-names = "tx", "rx", "cmd";
+			status = "disabled";
+		};
+
+		tcsr_mutex: hwlock@1f40000 {
+			compatible = "qcom,tcsr-mutex";
+			reg = <0x01f40000 0x40000>;
+			#hwlock-cells = <1>;
+		};
+
+		remoteproc_mpss: remoteproc@4080000 {
+			compatible = "qcom,sdx55-mpss-pas";
+			reg = <0x04080000 0x4040>;
+
+			interrupts-extended = <&intc GIC_SPI 250 IRQ_TYPE_EDGE_RISING>,
+					      <&modem_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
+					      <&modem_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
+					      <&modem_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
+					      <&modem_smp2p_in 3 IRQ_TYPE_EDGE_RISING>,
+					      <&modem_smp2p_in 7 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "wdog", "fatal", "ready", "handover",
+					  "stop-ack", "shutdown-ack";
+
+			clocks = <&rpmhcc RPMH_CXO_CLK>;
+			clock-names = "xo";
+
+			power-domains = <&rpmhpd SDX65_CX>,
+					<&rpmhpd SDX65_MSS>;
+			power-domain-names = "cx", "mss";
+
+			qcom,smem-states = <&modem_smp2p_out 0>;
+			qcom,smem-state-names = "stop";
+
+			status = "disabled";
+
+			glink-edge {
+				interrupts = <GIC_SPI 114 IRQ_TYPE_EDGE_RISING>;
+				label = "mpss";
+				qcom,remote-pid = <1>;
+				mboxes = <&apcs 15>;
+			};
+		};
+
+		sdhc_1: mmc@8804000 {
+			compatible = "qcom,sdx65-sdhci", "qcom,sdhci-msm-v5";
+			reg = <0x08804000 0x1000>;
+			reg-names = "hc";
+			interrupts = <GIC_SPI 210 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 227 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hc_irq", "pwr_irq";
+			clocks = <&gcc GCC_SDCC1_APPS_CLK>,
+				 <&gcc GCC_SDCC1_AHB_CLK>;
+			clock-names = "core", "iface";
+			status = "disabled";
+		};
+
+		mem_noc: interconnect@9680000 {
+			compatible = "qcom,sdx65-mem-noc";
+			reg = <0x09680000 0x27200>;
+			#interconnect-cells = <1>;
+			qcom,bcm-voters = <&apps_bcm_voter>;
+		};
+
+		usb: usb@a6f8800 {
+			compatible = "qcom,sdx65-dwc3", "qcom,dwc3";
+			reg = <0x0a6f8800 0x400>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			clocks = <&gcc GCC_USB30_SLV_AHB_CLK>,
+				 <&gcc GCC_USB30_MASTER_CLK>,
+				 <&gcc GCC_USB30_MSTR_AXI_CLK>,
+				 <&gcc GCC_USB30_MOCK_UTMI_CLK>,
+				 <&gcc GCC_USB30_SLEEP_CLK>;
+			clock-names = "cfg_noc", "core", "iface", "mock_utmi",
+					"sleep";
+
+			assigned-clocks = <&gcc GCC_USB30_MOCK_UTMI_CLK>,
+					  <&gcc GCC_USB30_MASTER_CLK>;
+			assigned-clock-rates = <19200000>, <200000000>;
+
+			interrupts-extended = <&intc GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>,
+					      <&pdc 76 IRQ_TYPE_LEVEL_HIGH>,
+					      <&pdc 18 IRQ_TYPE_EDGE_BOTH>,
+					      <&pdc 19 IRQ_TYPE_EDGE_BOTH>;
+			interrupt-names = "hs_phy_irq",
+					  "ss_phy_irq",
+					  "dm_hs_phy_irq",
+					  "dp_hs_phy_irq";
+
+			power-domains = <&gcc USB30_GDSC>;
+
+			resets = <&gcc GCC_USB30_BCR>;
+
+			usb_dwc3: usb@a600000 {
+				compatible = "snps,dwc3";
+				reg = <0x0a600000 0xcd00>;
+				interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
+				iommus = <&apps_smmu 0x1a0 0x0>;
+				snps,dis_u2_susphy_quirk;
+				snps,dis_enblslpm_quirk;
+				phys = <&usb_hsphy>, <&usb_ssphy>;
+				phy-names = "usb2-phy", "usb3-phy";
+			};
+		};
+
+		restart@c264000 {
+			compatible = "qcom,pshold";
+			reg = <0x0c264000 0x1000>;
+		};
+
+		spmi_bus: qcom,spmi@c440000 {
+			compatible = "qcom,spmi-pmic-arb";
+			reg = <0xc440000 0xd00>,
+				<0xc600000 0x2000000>,
+				<0xe600000 0x100000>,
+				<0xe700000 0xa0000>,
+				<0xc40a000 0x26000>;
+			reg-names = "core", "chnls", "obsrvr", "intr", "cnfg";
+			interrupts-extended = <&pdc 1 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "periph_irq";
+			interrupt-controller;
+			#interrupt-cells = <4>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+			cell-index = <0>;
+			qcom,channel = <0>;
+			qcom,ee = <0>;
+		};
+
+		tlmm: pinctrl@f100000 {
+			compatible = "qcom,sdx65-tlmm";
+			reg = <0xf100000 0x300000>;
+			interrupts = <GIC_SPI 212 IRQ_TYPE_LEVEL_HIGH>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&tlmm 0 0 109>;
+			interrupt-controller;
+			interrupt-parent = <&intc>;
+			#interrupt-cells = <2>;
+		};
+
+		pdc: interrupt-controller@b210000 {
+			compatible = "qcom,sdx65-pdc", "qcom,pdc";
+			reg = <0xb210000 0x10000>;
+			qcom,pdc-ranges = <0 147 52>, <52 266 32>;
+			#interrupt-cells = <2>;
+			interrupt-parent = <&intc>;
+			interrupt-controller;
+		};
+
+		imem@1468f000 {
+			compatible = "simple-mfd";
+			reg = <0x1468f000 0x1000>;
+			ranges = <0x0 0x1468f000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			pil-reloc@94c {
+				compatible = "qcom,pil-reloc-info";
+				reg = <0x94c 0xc8>;
+			};
+		};
+
+		apps_smmu: iommu@15000000 {
+			compatible = "qcom,sdx65-smmu-500", "arm,mmu-500";
+			reg = <0x15000000 0x40000>;
+			#iommu-cells = <2>;
+			#global-interrupts = <1>;
+			interrupts =	<GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 298 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 299 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 300 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 301 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 302 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 303 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 304 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 305 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 306 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 307 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 308 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		intc: interrupt-controller@17800000 {
+			compatible = "qcom,msm-qgic2";
+			interrupt-controller;
+			interrupt-parent = <&intc>;
+			#interrupt-cells = <3>;
+			reg = <0x17800000 0x1000>,
+			      <0x17802000 0x1000>;
+		};
+
+		a7pll: clock@17808000 {
+			compatible = "qcom,sdx55-a7pll";
+			reg = <0x17808000 0x1000>;
+			clocks = <&rpmhcc RPMH_CXO_CLK>;
+			clock-names = "bi_tcxo";
+			#clock-cells = <0>;
+		};
+
+		apcs: mailbox@17810000 {
+			compatible = "qcom,sdx55-apcs-gcc", "syscon";
+			reg = <0x17810000 0x2000>;
+			#mbox-cells = <1>;
+			clocks = <&rpmhcc RPMH_CXO_CLK>, <&a7pll>, <&gcc GPLL0>;
+			clock-names = "ref", "pll", "aux";
+			#clock-cells = <0>;
+		};
+
+		watchdog@17817000 {
+			compatible = "qcom,apss-wdt-sdx65", "qcom,kpss-wdt";
+			reg = <0x17817000 0x1000>;
+			clocks = <&sleep_clk>;
+		};
+
+		timer@17820000 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			compatible = "arm,armv7-timer-mem";
+			reg = <0x17820000 0x1000>;
+			clock-frequency = <19200000>;
+
+			frame@17821000 {
+				frame-number = <0>;
+				interrupts = <GIC_SPI 7 0x4>,
+					     <GIC_SPI 6 0x4>;
+				reg = <0x17821000 0x1000>,
+				      <0x17822000 0x1000>;
+			};
+
+			frame@17823000 {
+				frame-number = <1>;
+				interrupts = <GIC_SPI 8 0x4>;
+				reg = <0x17823000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@17824000 {
+				frame-number = <2>;
+				interrupts = <GIC_SPI 9 0x4>;
+				reg = <0x17824000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@17825000 {
+				frame-number = <3>;
+				interrupts = <GIC_SPI 10 0x4>;
+				reg = <0x17825000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@17826000 {
+				frame-number = <4>;
+				interrupts = <GIC_SPI 11 0x4>;
+				reg = <0x17826000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@17827000 {
+				frame-number = <5>;
+				interrupts = <GIC_SPI 12 0x4>;
+				reg = <0x17827000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@17828000 {
+				frame-number = <6>;
+				interrupts = <GIC_SPI 13 0x4>;
+				reg = <0x17828000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@17829000 {
+				frame-number = <7>;
+				interrupts = <GIC_SPI 14 0x4>;
+				reg = <0x17829000 0x1000>;
+				status = "disabled";
+			};
+		};
+
+		apps_rsc: rsc@17830000 {
+			label = "apps_rsc";
+			compatible = "qcom,rpmh-rsc";
+			reg = <0x17830000 0x10000>,
+			    <0x17840000 0x10000>;
+			reg-names = "drv-0", "drv-1";
+			interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>,
+				   <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
+			qcom,tcs-offset = <0xd00>;
+			qcom,drv-id = <1>;
+			qcom,tcs-config = <ACTIVE_TCS  2>,
+				<SLEEP_TCS   2>,
+				<WAKE_TCS    2>,
+				<CONTROL_TCS 1>;
+
+			rpmhcc: clock-controller {
+				compatible = "qcom,sdx65-rpmh-clk";
+				#clock-cells = <1>;
+				clock-names = "xo";
+				clocks = <&xo_board>;
+			};
+
+			rpmhpd: power-controller {
+				compatible = "qcom,sdx65-rpmhpd";
+				#power-domain-cells = <1>;
+				operating-points-v2 = <&rpmhpd_opp_table>;
+
+				rpmhpd_opp_table: opp-table {
+					compatible = "operating-points-v2";
+
+					rpmhpd_opp_ret: opp1 {
+						opp-level = <RPMH_REGULATOR_LEVEL_RETENTION>;
+					};
+
+					rpmhpd_opp_min_svs: opp2 {
+						opp-level = <RPMH_REGULATOR_LEVEL_MIN_SVS>;
+					};
+
+					rpmhpd_opp_low_svs: opp3 {
+						opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>;
+					};
+
+					rpmhpd_opp_svs: opp4 {
+						opp-level = <RPMH_REGULATOR_LEVEL_SVS>;
+					};
+
+					rpmhpd_opp_svs_l1: opp5 {
+						opp-level = <RPMH_REGULATOR_LEVEL_SVS_L1>;
+					};
+
+					rpmhpd_opp_nom: opp6 {
+						opp-level = <RPMH_REGULATOR_LEVEL_NOM>;
+					};
+
+					rpmhpd_opp_nom_l1: opp7 {
+						opp-level = <RPMH_REGULATOR_LEVEL_NOM_L1>;
+					};
+
+					rpmhpd_opp_nom_l2: opp8 {
+						opp-level = <RPMH_REGULATOR_LEVEL_NOM_L2>;
+					};
+
+					rpmhpd_opp_turbo: opp9 {
+						opp-level = <RPMH_REGULATOR_LEVEL_TURBO>;
+					};
+
+					rpmhpd_opp_turbo_l1: opp10 {
+						opp-level = <RPMH_REGULATOR_LEVEL_TURBO_L1>;
+					};
+				};
+			};
+
+			apps_bcm_voter: bcm-voter {
+				compatible = "qcom,bcm-voter";
+			};
+
+		};
+	};
+
+	timer {
+		compatible = "arm,armv7-timer";
+		interrupts = <1 13 0xf08>,
+			<1 12 0xf08>,
+			<1 10 0xf08>,
+			<1 11 0xf08>;
+		clock-frequency = <19200000>;
+	};
+};
diff --git a/arch/arm/boot/dts/r7s9210-rza2mevb.dts b/arch/arm/boot/dts/r7s9210-rza2mevb.dts
index 9c0d9686fe01..69a5a44b8a2f 100644
--- a/arch/arm/boot/dts/r7s9210-rza2mevb.dts
+++ b/arch/arm/boot/dts/r7s9210-rza2mevb.dts
@@ -71,10 +71,10 @@
 	leds {
 		compatible = "gpio-leds";
 
-		red {
+		led-red {
 			gpios = <&pinctrl RZA2_PIN(PORT6, 0) GPIO_ACTIVE_HIGH>;
 		};
-		green {
+		led-green {
 			gpios = <&pinctrl RZA2_PIN(PORTC, 1) GPIO_ACTIVE_HIGH>;
 		};
 	};
diff --git a/arch/arm/boot/dts/r8a7740-armadillo800eva.dts b/arch/arm/boot/dts/r8a7740-armadillo800eva.dts
index a01f3def1c69..0af63ddc4473 100644
--- a/arch/arm/boot/dts/r8a7740-armadillo800eva.dts
+++ b/arch/arm/boot/dts/r8a7740-armadillo800eva.dts
@@ -266,7 +266,7 @@
 		function = "lcd0";
 	};
 
-	lcd0_mux {
+	lcd0-mux-hog {
 		/* DBGMD/LCDC0/FSIA MUX */
 		gpio-hog;
 		gpios = <176 0>;
diff --git a/arch/arm/boot/dts/r8a7742-iwg21d-q7-dbcm-ca.dts b/arch/arm/boot/dts/r8a7742-iwg21d-q7-dbcm-ca.dts
index 33db5938f2d4..4e58c54cde17 100644
--- a/arch/arm/boot/dts/r8a7742-iwg21d-q7-dbcm-ca.dts
+++ b/arch/arm/boot/dts/r8a7742-iwg21d-q7-dbcm-ca.dts
@@ -44,6 +44,22 @@
 		#clock-cells = <0>;
 		clock-frequency = <26000000>;
 	};
+
+	reg_1p8v: 1p8v {
+		compatible = "regulator-fixed";
+		regulator-name = "1P8V";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
+	};
+
+	reg_2p8v: 2p8v {
+		compatible = "regulator-fixed";
+		regulator-name = "2P8V";
+		regulator-min-microvolt = <2800000>;
+		regulator-max-microvolt = <2800000>;
+		regulator-always-on;
+	};
 };
 
 &avb {
@@ -75,10 +91,10 @@
 
 &gpio0 {
 	/* Disable hogging GP0_18 to output LOW */
-	/delete-node/ qspi_en;
+	/delete-node/ qspi-en-hog;
 
 	/* Hog GP0_18 to output HIGH to enable VIN2 */
-	vin2_en {
+	vin2-en-hog {
 		gpio-hog;
 		gpios = <18 GPIO_ACTIVE_HIGH>;
 		output-high;
diff --git a/arch/arm/boot/dts/r8a7742-iwg21d-q7-dbcm-ov5640-single.dtsi b/arch/arm/boot/dts/r8a7742-iwg21d-q7-dbcm-ov5640-single.dtsi
index 70c72ba4fe72..40cef0b1d1e6 100644
--- a/arch/arm/boot/dts/r8a7742-iwg21d-q7-dbcm-ov5640-single.dtsi
+++ b/arch/arm/boot/dts/r8a7742-iwg21d-q7-dbcm-ov5640-single.dtsi
@@ -17,6 +17,9 @@
 		reg = <0x3c>;
 		clocks = <&MCLK_CAM>;
 		clock-names = "xclk";
+		AVDD-supply = <&reg_2p8v>;
+		DOVDD-supply = <&reg_2p8v>;
+		DVDD-supply = <&reg_1p8v>;
 		status = "okay";
 
 		port {
diff --git a/arch/arm/boot/dts/r8a7742-iwg21d-q7.dts b/arch/arm/boot/dts/r8a7742-iwg21d-q7.dts
index a5a79cdbcd0e..64102b664055 100644
--- a/arch/arm/boot/dts/r8a7742-iwg21d-q7.dts
+++ b/arch/arm/boot/dts/r8a7742-iwg21d-q7.dts
@@ -226,7 +226,7 @@
 };
 
 &gpio0 {
-	touch-interrupt {
+	touch-interrupt-hog {
 		gpio-hog;
 		gpios = <24 GPIO_ACTIVE_LOW>;
 		input;
@@ -234,7 +234,7 @@
 };
 
 &gpio1 {
-	can-trx-en-gpio{
+	can-trx-en-hog {
 		gpio-hog;
 		gpios = <28 GPIO_ACTIVE_HIGH>;
 		output-low;
diff --git a/arch/arm/boot/dts/r8a7742-iwg21m.dtsi b/arch/arm/boot/dts/r8a7742-iwg21m.dtsi
index 5621c9ed698f..b281a4d164b0 100644
--- a/arch/arm/boot/dts/r8a7742-iwg21m.dtsi
+++ b/arch/arm/boot/dts/r8a7742-iwg21m.dtsi
@@ -37,7 +37,7 @@
 
 &gpio0 {
 	/* GP0_18 set low to select QSPI. Doing so will disable VIN2 */
-	qspi_en {
+	qspi-en-hog {
 		gpio-hog;
 		gpios = <18 GPIO_ACTIVE_HIGH>;
 		output-low;
diff --git a/arch/arm/boot/dts/r8a7742.dtsi b/arch/arm/boot/dts/r8a7742.dtsi
index 420e0b3259d4..758a1bf02fae 100644
--- a/arch/arm/boot/dts/r8a7742.dtsi
+++ b/arch/arm/boot/dts/r8a7742.dtsi
@@ -633,7 +633,7 @@
 			status = "disabled";
 		};
 
-		usbphy: usb-phy@e6590100 {
+		usbphy: usb-phy-controller@e6590100 {
 			compatible = "renesas,usb-phy-r8a7742",
 				     "renesas,rcar-gen2-usb-phy";
 			reg = <0 0xe6590100 0 0x100>;
@@ -645,11 +645,11 @@
 			resets = <&cpg 704>;
 			status = "disabled";
 
-			usb0: usb-channel@0 {
+			usb0: usb-phy@0 {
 				reg = <0>;
 				#phy-cells = <1>;
 			};
-			usb2: usb-channel@2 {
+			usb2: usb-phy@2 {
 				reg = <2>;
 				#phy-cells = <1>;
 			};
diff --git a/arch/arm/boot/dts/r8a7743.dtsi b/arch/arm/boot/dts/r8a7743.dtsi
index 3502b5dcc04f..20f1d98a048d 100644
--- a/arch/arm/boot/dts/r8a7743.dtsi
+++ b/arch/arm/boot/dts/r8a7743.dtsi
@@ -140,6 +140,7 @@
 			compatible = "renesas,r8a7743-wdt",
 				     "renesas,rcar-gen2-wdt";
 			reg = <0 0xe6020000 0 0x0c>;
+			interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 402>;
 			power-domains = <&sysc R8A7743_PD_ALWAYS_ON>;
 			resets = <&cpg 402>;
@@ -583,7 +584,7 @@
 			status = "disabled";
 		};
 
-		usbphy: usb-phy@e6590100 {
+		usbphy: usb-phy-controller@e6590100 {
 			compatible = "renesas,usb-phy-r8a7743",
 				     "renesas,rcar-gen2-usb-phy";
 			reg = <0 0xe6590100 0 0x100>;
@@ -595,11 +596,11 @@
 			resets = <&cpg 704>;
 			status = "disabled";
 
-			usb0: usb-channel@0 {
+			usb0: usb-phy@0 {
 				reg = <0>;
 				#phy-cells = <1>;
 			};
-			usb2: usb-channel@2 {
+			usb2: usb-phy@2 {
 				reg = <2>;
 				#phy-cells = <1>;
 			};
diff --git a/arch/arm/boot/dts/r8a7744.dtsi b/arch/arm/boot/dts/r8a7744.dtsi
index f5d4b8b85b6d..96b2d5a4e8f6 100644
--- a/arch/arm/boot/dts/r8a7744.dtsi
+++ b/arch/arm/boot/dts/r8a7744.dtsi
@@ -140,6 +140,7 @@
 			compatible = "renesas,r8a7744-wdt",
 				     "renesas,rcar-gen2-wdt";
 			reg = <0 0xe6020000 0 0x0c>;
+			interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 402>;
 			power-domains = <&sysc R8A7744_PD_ALWAYS_ON>;
 			resets = <&cpg 402>;
@@ -583,7 +584,7 @@
 			status = "disabled";
 		};
 
-		usbphy: usb-phy@e6590100 {
+		usbphy: usb-phy-controller@e6590100 {
 			compatible = "renesas,usb-phy-r8a7744",
 				     "renesas,rcar-gen2-usb-phy";
 			reg = <0 0xe6590100 0 0x100>;
@@ -595,11 +596,11 @@
 			resets = <&cpg 704>;
 			status = "disabled";
 
-			usb0: usb-channel@0 {
+			usb0: usb-phy@0 {
 				reg = <0>;
 				#phy-cells = <1>;
 			};
-			usb2: usb-channel@2 {
+			usb2: usb-phy@2 {
 				reg = <2>;
 				#phy-cells = <1>;
 			};
diff --git a/arch/arm/boot/dts/r8a7745.dtsi b/arch/arm/boot/dts/r8a7745.dtsi
index f877c51f769c..afc902e532d8 100644
--- a/arch/arm/boot/dts/r8a7745.dtsi
+++ b/arch/arm/boot/dts/r8a7745.dtsi
@@ -270,6 +270,7 @@
 		rwdt: watchdog@e6020000 {
 			compatible = "renesas,r8a7745-wdt",
 				     "renesas,rcar-gen2-wdt";
+			interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
 			reg = <0 0xe6020000 0 0x0c>;
 			clocks = <&cpg CPG_MOD 402>;
 			power-domains = <&sysc R8A7745_PD_ALWAYS_ON>;
@@ -524,7 +525,7 @@
 			status = "disabled";
 		};
 
-		usbphy: usb-phy@e6590100 {
+		usbphy: usb-phy-controller@e6590100 {
 			compatible = "renesas,usb-phy-r8a7745",
 				     "renesas,rcar-gen2-usb-phy";
 			reg = <0 0xe6590100 0 0x100>;
@@ -536,11 +537,11 @@
 			resets = <&cpg 704>;
 			status = "disabled";
 
-			usb0: usb-channel@0 {
+			usb0: usb-phy@0 {
 				reg = <0>;
 				#phy-cells = <1>;
 			};
-			usb2: usb-channel@2 {
+			usb2: usb-phy@2 {
 				reg = <2>;
 				#phy-cells = <1>;
 			};
diff --git a/arch/arm/boot/dts/r8a77470-iwg23s-sbc.dts b/arch/arm/boot/dts/r8a77470-iwg23s-sbc.dts
index b024621c9981..644802285249 100644
--- a/arch/arm/boot/dts/r8a77470-iwg23s-sbc.dts
+++ b/arch/arm/boot/dts/r8a77470-iwg23s-sbc.dts
@@ -116,7 +116,7 @@
 };
 
 &gpio2 {
-	interrupt-fixup {
+	interrupt-fixup-hog {
 		gpio-hog;
 		gpios = <29 GPIO_ACTIVE_HIGH>;
 		line-name = "hdmi-hpd-int";
diff --git a/arch/arm/boot/dts/r8a77470.dtsi b/arch/arm/boot/dts/r8a77470.dtsi
index 13ef1e9bf4d5..a5cf663a0118 100644
--- a/arch/arm/boot/dts/r8a77470.dtsi
+++ b/arch/arm/boot/dts/r8a77470.dtsi
@@ -91,6 +91,7 @@
 			compatible = "renesas,r8a77470-wdt",
 				     "renesas,rcar-gen2-wdt";
 			reg = <0 0xe6020000 0 0x0c>;
+			interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 402>;
 			power-domains = <&sysc R8A77470_PD_ALWAYS_ON>;
 			resets = <&cpg 402>;
@@ -356,7 +357,7 @@
 			status = "disabled";
 		};
 
-		usbphy0: usb-phy@e6590100 {
+		usbphy0: usb-phy-controller@e6590100 {
 			compatible = "renesas,usb-phy-r8a77470",
 				     "renesas,rcar-gen2-usb-phy";
 			reg = <0 0xe6590100 0 0x100>;
@@ -368,7 +369,7 @@
 			resets = <&cpg 704>;
 			status = "disabled";
 
-			usb0: usb-channel@0 {
+			usb0: usb-phy@0 {
 				reg = <0>;
 				#phy-cells = <1>;
 			};
@@ -392,7 +393,7 @@
 			status = "disabled";
 		};
 
-		usbphy1: usb-phy@e6598100 {
+		usbphy1: usb-phy-controller@e6598100 {
 			compatible = "renesas,usb-phy-r8a77470",
 				     "renesas,rcar-gen2-usb-phy";
 			reg = <0 0xe6598100 0 0x100>;
@@ -404,7 +405,7 @@
 			resets = <&cpg 706>;
 			status = "disabled";
 
-			usb1: usb-channel@0 {
+			usb1: usb-phy@0 {
 				reg = <0>;
 				#phy-cells = <1>;
 			};
diff --git a/arch/arm/boot/dts/r8a7790-lager.dts b/arch/arm/boot/dts/r8a7790-lager.dts
index 57cd2fa72249..5ad5349a50dc 100644
--- a/arch/arm/boot/dts/r8a7790-lager.dts
+++ b/arch/arm/boot/dts/r8a7790-lager.dts
@@ -442,7 +442,7 @@
 				compatible = "dlg,da9063-rtc";
 			};
 
-			wdt {
+			watchdog {
 				compatible = "dlg,da9063-watchdog";
 			};
 		};
diff --git a/arch/arm/boot/dts/r8a7790-stout.dts b/arch/arm/boot/dts/r8a7790-stout.dts
index c802f9f13c18..fe14727eefe1 100644
--- a/arch/arm/boot/dts/r8a7790-stout.dts
+++ b/arch/arm/boot/dts/r8a7790-stout.dts
@@ -341,7 +341,7 @@
 			compatible = "dlg,da9063-rtc";
 		};
 
-		wdt {
+		watchdog {
 			compatible = "dlg,da9063-watchdog";
 		};
 	};
diff --git a/arch/arm/boot/dts/r8a7790.dtsi b/arch/arm/boot/dts/r8a7790.dtsi
index ed6dd4fcc503..db171e3c62f2 100644
--- a/arch/arm/boot/dts/r8a7790.dtsi
+++ b/arch/arm/boot/dts/r8a7790.dtsi
@@ -274,6 +274,7 @@
 			compatible = "renesas,r8a7790-wdt",
 				     "renesas,rcar-gen2-wdt";
 			reg = <0 0xe6020000 0 0x0c>;
+			interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 402>;
 			power-domains = <&sysc R8A7790_PD_ALWAYS_ON>;
 			resets = <&cpg 402>;
@@ -653,7 +654,7 @@
 			status = "disabled";
 		};
 
-		usbphy: usb-phy@e6590100 {
+		usbphy: usb-phy-controller@e6590100 {
 			compatible = "renesas,usb-phy-r8a7790",
 				     "renesas,rcar-gen2-usb-phy";
 			reg = <0 0xe6590100 0 0x100>;
@@ -665,11 +666,11 @@
 			resets = <&cpg 704>;
 			status = "disabled";
 
-			usb0: usb-channel@0 {
+			usb0: usb-phy@0 {
 				reg = <0>;
 				#phy-cells = <1>;
 			};
-			usb2: usb-channel@2 {
+			usb2: usb-phy@2 {
 				reg = <2>;
 				#phy-cells = <1>;
 			};
diff --git a/arch/arm/boot/dts/r8a7791-koelsch.dts b/arch/arm/boot/dts/r8a7791-koelsch.dts
index 6e691b6cac05..26a40782cc89 100644
--- a/arch/arm/boot/dts/r8a7791-koelsch.dts
+++ b/arch/arm/boot/dts/r8a7791-koelsch.dts
@@ -805,7 +805,7 @@
 			compatible = "dlg,da9063-rtc";
 		};
 
-		wdt {
+		watchdog {
 			compatible = "dlg,da9063-watchdog";
 		};
 	};
diff --git a/arch/arm/boot/dts/r8a7791-porter.dts b/arch/arm/boot/dts/r8a7791-porter.dts
index 38e2ab928707..ec0a20d5130d 100644
--- a/arch/arm/boot/dts/r8a7791-porter.dts
+++ b/arch/arm/boot/dts/r8a7791-porter.dts
@@ -390,7 +390,7 @@
 		interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
 		interrupt-controller;
 
-		wdt {
+		watchdog {
 			compatible = "dlg,da9063-watchdog";
 		};
 	};
diff --git a/arch/arm/boot/dts/r8a7791.dtsi b/arch/arm/boot/dts/r8a7791.dtsi
index 0ccc162d3c2c..d8f91d9f42ae 100644
--- a/arch/arm/boot/dts/r8a7791.dtsi
+++ b/arch/arm/boot/dts/r8a7791.dtsi
@@ -161,6 +161,7 @@
 			compatible = "renesas,r8a7791-wdt",
 				     "renesas,rcar-gen2-wdt";
 			reg = <0 0xe6020000 0 0x0c>;
+			interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 402>;
 			power-domains = <&sysc R8A7791_PD_ALWAYS_ON>;
 			resets = <&cpg 402>;
@@ -607,7 +608,7 @@
 			status = "disabled";
 		};
 
-		usbphy: usb-phy@e6590100 {
+		usbphy: usb-phy-controller@e6590100 {
 			compatible = "renesas,usb-phy-r8a7791",
 				     "renesas,rcar-gen2-usb-phy";
 			reg = <0 0xe6590100 0 0x100>;
@@ -619,11 +620,11 @@
 			resets = <&cpg 704>;
 			status = "disabled";
 
-			usb0: usb-channel@0 {
+			usb0: usb-phy@0 {
 				reg = <0>;
 				#phy-cells = <1>;
 			};
-			usb2: usb-channel@2 {
+			usb2: usb-phy@2 {
 				reg = <2>;
 				#phy-cells = <1>;
 			};
diff --git a/arch/arm/boot/dts/r8a7792-blanche.dts b/arch/arm/boot/dts/r8a7792-blanche.dts
index 62aa9f61321b..c66de9dd12df 100644
--- a/arch/arm/boot/dts/r8a7792-blanche.dts
+++ b/arch/arm/boot/dts/r8a7792-blanche.dts
@@ -335,7 +335,7 @@
 			compatible = "dlg,da9063-rtc";
 		};
 
-		wdt {
+		watchdog {
 			compatible = "dlg,da9063-watchdog";
 		};
 	};
diff --git a/arch/arm/boot/dts/r8a7792.dtsi b/arch/arm/boot/dts/r8a7792.dtsi
index 9cdb73894ac2..a6d9367f8fa0 100644
--- a/arch/arm/boot/dts/r8a7792.dtsi
+++ b/arch/arm/boot/dts/r8a7792.dtsi
@@ -111,6 +111,7 @@
 			compatible = "renesas,r8a7792-wdt",
 				     "renesas,rcar-gen2-wdt";
 			reg = <0 0xe6020000 0 0x0c>;
+			interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 402>;
 			power-domains = <&sysc R8A7792_PD_ALWAYS_ON>;
 			resets = <&cpg 402>;
diff --git a/arch/arm/boot/dts/r8a7793-gose.dts b/arch/arm/boot/dts/r8a7793-gose.dts
index c8978f4f62e9..79b537b24642 100644
--- a/arch/arm/boot/dts/r8a7793-gose.dts
+++ b/arch/arm/boot/dts/r8a7793-gose.dts
@@ -740,7 +740,7 @@
 			compatible = "dlg,da9063-rtc";
 		};
 
-		wdt {
+		watchdog {
 			compatible = "dlg,da9063-watchdog";
 		};
 	};
diff --git a/arch/arm/boot/dts/r8a7793.dtsi b/arch/arm/boot/dts/r8a7793.dtsi
index dea4b1e108af..9ebe7bfaf0ed 100644
--- a/arch/arm/boot/dts/r8a7793.dtsi
+++ b/arch/arm/boot/dts/r8a7793.dtsi
@@ -146,6 +146,7 @@
 			compatible = "renesas,r8a7793-wdt",
 				     "renesas,rcar-gen2-wdt";
 			reg = <0 0xe6020000 0 0x0c>;
+			interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 402>;
 			power-domains = <&sysc R8A7793_PD_ALWAYS_ON>;
 			resets = <&cpg 402>;
diff --git a/arch/arm/boot/dts/r8a7794-alt.dts b/arch/arm/boot/dts/r8a7794-alt.dts
index 99d554fe3329..4d93319674c6 100644
--- a/arch/arm/boot/dts/r8a7794-alt.dts
+++ b/arch/arm/boot/dts/r8a7794-alt.dts
@@ -463,7 +463,7 @@
 			compatible = "dlg,da9063-rtc";
 		};
 
-		wdt {
+		watchdog {
 			compatible = "dlg,da9063-watchdog";
 		};
 	};
diff --git a/arch/arm/boot/dts/r8a7794-silk.dts b/arch/arm/boot/dts/r8a7794-silk.dts
index 92a76164432a..b7af1befa126 100644
--- a/arch/arm/boot/dts/r8a7794-silk.dts
+++ b/arch/arm/boot/dts/r8a7794-silk.dts
@@ -433,7 +433,7 @@
 			compatible = "dlg,da9063-rtc";
 		};
 
-		wdt {
+		watchdog {
 			compatible = "dlg,da9063-watchdog";
 		};
 	};
diff --git a/arch/arm/boot/dts/r8a7794.dtsi b/arch/arm/boot/dts/r8a7794.dtsi
index eac9ed8df0be..7aa781ff3bff 100644
--- a/arch/arm/boot/dts/r8a7794.dtsi
+++ b/arch/arm/boot/dts/r8a7794.dtsi
@@ -128,6 +128,7 @@
 			compatible = "renesas,r8a7794-wdt",
 				     "renesas,rcar-gen2-wdt";
 			reg = <0 0xe6020000 0 0x0c>;
+			interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 402>;
 			power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
 			resets = <&cpg 402>;
@@ -505,7 +506,7 @@
 			status = "disabled";
 		};
 
-		usbphy: usb-phy@e6590100 {
+		usbphy: usb-phy-controller@e6590100 {
 			compatible = "renesas,usb-phy-r8a7794",
 				     "renesas,rcar-gen2-usb-phy";
 			reg = <0 0xe6590100 0 0x100>;
@@ -517,11 +518,11 @@
 			resets = <&cpg 704>;
 			status = "disabled";
 
-			usb0: usb-channel@0 {
+			usb0: usb-phy@0 {
 				reg = <0>;
 				#phy-cells = <1>;
 			};
-			usb2: usb-channel@2 {
+			usb2: usb-phy@2 {
 				reg = <2>;
 				#phy-cells = <1>;
 			};
diff --git a/arch/arm/boot/dts/r8a77xx-aa104xd12-panel.dtsi b/arch/arm/boot/dts/r8a77xx-aa104xd12-panel.dtsi
deleted file mode 100644
index 79fce67ebb1c..000000000000
--- a/arch/arm/boot/dts/r8a77xx-aa104xd12-panel.dtsi
+++ /dev/null
@@ -1,39 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Common file for the AA104XD12 panel connected to Renesas R-Car boards
- *
- * Copyright (C) 2014 Renesas Electronics Corp.
- */
-
-/ {
-	panel {
-		compatible = "mitsubishi,aa104xd12", "panel-lvds";
-
-		width-mm = <210>;
-		height-mm = <158>;
-		data-mapping = "jeida-18";
-
-		panel-timing {
-			/* 1024x768 @65Hz */
-			clock-frequency = <65000000>;
-			hactive = <1024>;
-			vactive = <768>;
-			hsync-len = <136>;
-			hfront-porch = <20>;
-			hback-porch = <160>;
-			vfront-porch = <3>;
-			vback-porch = <29>;
-			vsync-len = <6>;
-		};
-
-		port {
-			panel_in: endpoint {
-				remote-endpoint = <&lvds_connector>;
-			};
-		};
-	};
-};
-
-&lvds_connector {
-	remote-endpoint = <&panel_in>;
-};
diff --git a/arch/arm/boot/dts/r9a06g032-rzn1d400-db.dts b/arch/arm/boot/dts/r9a06g032-rzn1d400-db.dts
index 4e57ae2688fc..c18bbd7141c4 100644
--- a/arch/arm/boot/dts/r9a06g032-rzn1d400-db.dts
+++ b/arch/arm/boot/dts/r9a06g032-rzn1d400-db.dts
@@ -8,6 +8,9 @@
 
 /dts-v1/;
 
+#include <dt-bindings/pinctrl/rzn1-pinctrl.h>
+#include <dt-bindings/net/pcs-rzn1-miic.h>
+
 #include "r9a06g032.dtsi"
 
 / {
@@ -23,6 +26,155 @@
 	};
 };
 
+&can0 {
+	pinctrl-0 = <&pins_can0>;
+	pinctrl-names = "default";
+
+	/* Assuming CN10/CN11 are wired for CAN1 */
+	status = "okay";
+};
+
+&can1 {
+	pinctrl-0 = <&pins_can1>;
+	pinctrl-names = "default";
+
+	/* Please only enable can0 or can1, depending on CN10/CN11 */
+	/* status = "okay"; */
+};
+
+&eth_miic {
+	status = "okay";
+	renesas,miic-switch-portin = <MIIC_GMAC2_PORT>;
+};
+
+&gmac2 {
+	status = "okay";
+	phy-mode = "gmii";
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+};
+
+&mii_conv4 {
+	renesas,miic-input = <MIIC_SWITCH_PORTB>;
+	status = "okay";
+};
+
+&mii_conv5 {
+	renesas,miic-input = <MIIC_SWITCH_PORTA>;
+	status = "okay";
+};
+
+&pinctrl{
+	pins_can0: pins_can0 {
+		pinmux = <RZN1_PINMUX(162, RZN1_FUNC_CAN)>,	/* CAN0_TXD */
+			 <RZN1_PINMUX(163, RZN1_FUNC_CAN)>;	/* CAN0_RXD */
+		drive-strength = <6>;
+	};
+
+	pins_can1: pins_can1 {
+		pinmux = <RZN1_PINMUX(109, RZN1_FUNC_CAN)>,	/* CAN1_TXD */
+			 <RZN1_PINMUX(110, RZN1_FUNC_CAN)>;	/* CAN1_RXD */
+		drive-strength = <6>;
+	};
+
+	pins_eth3: pins_eth3 {
+		pinmux = <RZN1_PINMUX(36, RZN1_FUNC_CLK_ETH_MII_RGMII_RMII)>,
+			 <RZN1_PINMUX(37, RZN1_FUNC_CLK_ETH_MII_RGMII_RMII)>,
+			 <RZN1_PINMUX(38, RZN1_FUNC_CLK_ETH_MII_RGMII_RMII)>,
+			 <RZN1_PINMUX(39, RZN1_FUNC_CLK_ETH_MII_RGMII_RMII)>,
+			 <RZN1_PINMUX(40, RZN1_FUNC_CLK_ETH_MII_RGMII_RMII)>,
+			 <RZN1_PINMUX(41, RZN1_FUNC_CLK_ETH_MII_RGMII_RMII)>,
+			 <RZN1_PINMUX(42, RZN1_FUNC_CLK_ETH_MII_RGMII_RMII)>,
+			 <RZN1_PINMUX(43, RZN1_FUNC_CLK_ETH_MII_RGMII_RMII)>,
+			 <RZN1_PINMUX(44, RZN1_FUNC_CLK_ETH_MII_RGMII_RMII)>,
+			 <RZN1_PINMUX(45, RZN1_FUNC_CLK_ETH_MII_RGMII_RMII)>,
+			 <RZN1_PINMUX(46, RZN1_FUNC_CLK_ETH_MII_RGMII_RMII)>,
+			 <RZN1_PINMUX(47, RZN1_FUNC_CLK_ETH_MII_RGMII_RMII)>;
+		drive-strength = <6>;
+		bias-disable;
+	};
+
+	pins_eth4: pins_eth4 {
+		pinmux = <RZN1_PINMUX(48, RZN1_FUNC_CLK_ETH_MII_RGMII_RMII)>,
+			 <RZN1_PINMUX(49, RZN1_FUNC_CLK_ETH_MII_RGMII_RMII)>,
+			 <RZN1_PINMUX(50, RZN1_FUNC_CLK_ETH_MII_RGMII_RMII)>,
+			 <RZN1_PINMUX(51, RZN1_FUNC_CLK_ETH_MII_RGMII_RMII)>,
+			 <RZN1_PINMUX(52, RZN1_FUNC_CLK_ETH_MII_RGMII_RMII)>,
+			 <RZN1_PINMUX(53, RZN1_FUNC_CLK_ETH_MII_RGMII_RMII)>,
+			 <RZN1_PINMUX(54, RZN1_FUNC_CLK_ETH_MII_RGMII_RMII)>,
+			 <RZN1_PINMUX(55, RZN1_FUNC_CLK_ETH_MII_RGMII_RMII)>,
+			 <RZN1_PINMUX(56, RZN1_FUNC_CLK_ETH_MII_RGMII_RMII)>,
+			 <RZN1_PINMUX(57, RZN1_FUNC_CLK_ETH_MII_RGMII_RMII)>,
+			 <RZN1_PINMUX(58, RZN1_FUNC_CLK_ETH_MII_RGMII_RMII)>,
+			 <RZN1_PINMUX(59, RZN1_FUNC_CLK_ETH_MII_RGMII_RMII)>;
+		drive-strength = <6>;
+		bias-disable;
+	};
+
+	pins_mdio1: pins_mdio1 {
+		pinmux = <RZN1_PINMUX(152, RZN1_FUNC_MDIO1_SWITCH)>,
+			 <RZN1_PINMUX(153, RZN1_FUNC_MDIO1_SWITCH)>;
+	};
+};
+
+&rtc0 {
+	status = "okay";
+};
+
+&switch {
+	status = "okay";
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pins_eth3>, <&pins_eth4>, <&pins_mdio1>;
+
+	dsa,member = <0 0>;
+
+	mdio {
+		clock-frequency = <2500000>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		switch0phy4: ethernet-phy@4 {
+			reg = <4>;
+			micrel,led-mode = <1>;
+		};
+
+		switch0phy5: ethernet-phy@5 {
+			reg = <5>;
+			micrel,led-mode = <1>;
+		};
+	};
+};
+
+&switch_port0 {
+	label = "lan0";
+	phy-mode = "mii";
+	phy-handle = <&switch0phy5>;
+	status = "okay";
+};
+
+&switch_port1 {
+	label = "lan1";
+	phy-mode = "mii";
+	phy-handle = <&switch0phy4>;
+	status = "okay";
+};
+
+&switch_port4 {
+	status = "okay";
+};
+
 &uart0 {
 	status = "okay";
 };
+
+&wdt0 {
+	timeout-sec = <60>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/r9a06g032.dtsi b/arch/arm/boot/dts/r9a06g032.dtsi
index c47896e4ab58..563024c9a4ae 100644
--- a/arch/arm/boot/dts/r9a06g032.dtsi
+++ b/arch/arm/boot/dts/r9a06g032.dtsi
@@ -66,15 +66,96 @@
 		interrupt-parent = <&gic>;
 		ranges;
 
+		rtc0: rtc@40006000 {
+			compatible = "renesas,r9a06g032-rtc", "renesas,rzn1-rtc";
+			reg = <0x40006000 0x1000>;
+			interrupts = <GIC_SPI 66 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 67 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 68 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "alarm", "timer", "pps";
+			clocks = <&sysctrl R9A06G032_HCLK_RTC>;
+			clock-names = "hclk";
+			power-domains = <&sysctrl>;
+			status = "disabled";
+		};
+
+		wdt0: watchdog@40008000 {
+			compatible = "renesas,r9a06g032-wdt", "renesas,rzn1-wdt";
+			reg = <0x40008000 0x1000>;
+			interrupts = <GIC_SPI 73 IRQ_TYPE_EDGE_RISING>;
+			clocks = <&sysctrl R9A06G032_CLK_WATCHDOG>;
+			status = "disabled";
+		};
+
+		wdt1: watchdog@40009000 {
+			compatible = "renesas,r9a06g032-wdt", "renesas,rzn1-wdt";
+			reg = <0x40009000 0x1000>;
+			interrupts = <GIC_SPI 74 IRQ_TYPE_EDGE_RISING>;
+			clocks = <&sysctrl R9A06G032_CLK_WATCHDOG>;
+			status = "disabled";
+		};
+
 		sysctrl: system-controller@4000c000 {
 			compatible = "renesas,r9a06g032-sysctrl";
 			reg = <0x4000c000 0x1000>;
 			status = "okay";
 			#clock-cells = <1>;
+			#power-domain-cells = <0>;
 
 			clocks = <&ext_mclk>, <&ext_rtc_clk>,
 					<&ext_jtag_clk>, <&ext_rgmii_ref>;
 			clock-names = "mclk", "rtc", "jtag", "rgmii_ref_ext";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			dmamux: dma-router@a0 {
+				compatible = "renesas,rzn1-dmamux";
+				reg = <0xa0 4>;
+				#dma-cells = <6>;
+				dma-requests = <32>;
+				dma-masters = <&dma0 &dma1>;
+			};
+		};
+
+		pci_usb: pci@40030000 {
+			compatible = "renesas,pci-r9a06g032", "renesas,pci-rzn1";
+			device_type = "pci";
+			clocks = <&sysctrl R9A06G032_HCLK_USBH>,
+				 <&sysctrl R9A06G032_HCLK_USBPM>,
+				 <&sysctrl R9A06G032_CLK_PCI_USB>;
+			clock-names = "hclkh", "hclkpm", "pciclk";
+			power-domains = <&sysctrl>;
+			reg = <0x40030000 0xc00>,
+			      <0x40020000 0x1100>;
+			interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+
+			bus-range = <0 0>;
+			#address-cells = <3>;
+			#size-cells = <2>;
+			#interrupt-cells = <1>;
+			ranges = <0x02000000 0 0x40020000 0x40020000 0 0x00010000>;
+			/* Should map all possible DDR as inbound ranges, but
+			 * the IP only supports a 256MB, 512MB, or 1GB window.
+			 * flags, PCI addr (64-bit), CPU addr, PCI size (64-bit)
+			 */
+			dma-ranges = <0x42000000 0 0x80000000 0x80000000 0 0x40000000>;
+			interrupt-map-mask = <0xf800 0 0 0x7>;
+			interrupt-map = <0x0000 0 0 1 &gic GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH
+					 0x0800 0 0 1 &gic GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH
+					 0x1000 0 0 2 &gic GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
+
+			usb@1,0 {
+				reg = <0x800 0 0 0 0>;
+				phys = <&usbphy>;
+				phy-names = "usb";
+			};
+
+			usb@2,0 {
+				reg = <0x1000 0 0 0 0>;
+				phys = <&usbphy>;
+				phy-names = "usb";
+			};
 		};
 
 		uart0: serial@40060000 {
@@ -118,6 +199,8 @@
 			reg-io-width = <4>;
 			clocks = <&sysctrl R9A06G032_CLK_UART3>, <&sysctrl R9A06G032_HCLK_UART3>;
 			clock-names = "baudclk", "apb_pclk";
+			dmas =  <&dmamux 0 0 0 0 0 1>, <&dmamux 1 0 0 0 1 1>;
+			dma-names = "rx", "tx";
 			status = "disabled";
 		};
 
@@ -129,6 +212,8 @@
 			reg-io-width = <4>;
 			clocks = <&sysctrl R9A06G032_CLK_UART4>, <&sysctrl R9A06G032_HCLK_UART4>;
 			clock-names = "baudclk", "apb_pclk";
+			dmas =  <&dmamux 2 0 0 0 2 1>, <&dmamux 3 0 0 0 3 1>;
+			dma-names = "rx", "tx";
 			status = "disabled";
 		};
 
@@ -140,6 +225,8 @@
 			reg-io-width = <4>;
 			clocks = <&sysctrl R9A06G032_CLK_UART5>, <&sysctrl R9A06G032_HCLK_UART5>;
 			clock-names = "baudclk", "apb_pclk";
+			dmas =  <&dmamux 4 0 0 0 4 1>, <&dmamux 5 0 0 0 5 1>;
+			dma-names = "rx", "tx";
 			status = "disabled";
 		};
 
@@ -151,6 +238,8 @@
 			reg-io-width = <4>;
 			clocks = <&sysctrl R9A06G032_CLK_UART6>, <&sysctrl R9A06G032_HCLK_UART6>;
 			clock-names = "baudclk", "apb_pclk";
+			dmas =  <&dmamux 6 0 0 0 6 1>, <&dmamux 7 0 0 0 7 1>;
+			dma-names = "rx", "tx";
 			status = "disabled";
 		};
 
@@ -162,6 +251,8 @@
 			reg-io-width = <4>;
 			clocks = <&sysctrl R9A06G032_CLK_UART7>, <&sysctrl R9A06G032_HCLK_UART7>;
 			clock-names = "baudclk", "apb_pclk";
+			dmas =  <&dmamux 4 0 0 0 20 1>, <&dmamux 5 0 0 0 21 1>;
+			dma-names = "rx", "tx";
 			status = "disabled";
 		};
 
@@ -173,6 +264,154 @@
 			status = "okay";
 		};
 
+		nand_controller: nand-controller@40102000 {
+			compatible = "renesas,r9a06g032-nandc", "renesas,rzn1-nandc";
+			reg = <0x40102000 0x2000>;
+			interrupts = <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&sysctrl R9A06G032_HCLK_NAND>, <&sysctrl R9A06G032_CLK_NAND>;
+			clock-names = "hclk", "eclk";
+			power-domains = <&sysctrl>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		dma0: dma-controller@40104000 {
+			compatible = "renesas,r9a06g032-dma", "renesas,rzn1-dma";
+			reg = <0x40104000 0x1000>;
+			interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>;
+			clock-names = "hclk";
+			clocks = <&sysctrl R9A06G032_HCLK_DMA0>;
+			dma-channels = <8>;
+			dma-requests = <16>;
+			dma-masters = <1>;
+			#dma-cells = <3>;
+			block_size = <0xfff>;
+			data-width = <8>;
+		};
+
+		dma1: dma-controller@40105000 {
+			compatible = "renesas,r9a06g032-dma", "renesas,rzn1-dma";
+			reg = <0x40105000 0x1000>;
+			interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
+			clock-names = "hclk";
+			clocks = <&sysctrl R9A06G032_HCLK_DMA1>;
+			dma-channels = <8>;
+			dma-requests = <16>;
+			dma-masters = <1>;
+			#dma-cells = <3>;
+			block_size = <0xfff>;
+			data-width = <8>;
+		};
+
+		gmac2: ethernet@44002000 {
+			compatible = "renesas,r9a06g032-gmac", "renesas,rzn1-gmac", "snps,dwmac";
+			reg = <0x44002000 0x2000>;
+			interrupt-parent = <&gic>;
+			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "macirq", "eth_wake_irq", "eth_lpi";
+			clocks = <&sysctrl R9A06G032_HCLK_GMAC1>;
+			clock-names = "stmmaceth";
+			power-domains = <&sysctrl>;
+			snps,multicast-filter-bins = <256>;
+			snps,perfect-filter-entries = <128>;
+			tx-fifo-depth = <2048>;
+			rx-fifo-depth = <4096>;
+			status = "disabled";
+		};
+
+		eth_miic: eth-miic@44030000 {
+			compatible = "renesas,r9a06g032-miic", "renesas,rzn1-miic";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x44030000 0x10000>;
+			clocks = <&sysctrl R9A06G032_CLK_MII_REF>,
+				 <&sysctrl R9A06G032_CLK_RGMII_REF>,
+				 <&sysctrl R9A06G032_CLK_RMII_REF>,
+				 <&sysctrl R9A06G032_HCLK_SWITCH_RG>;
+			clock-names = "mii_ref", "rgmii_ref", "rmii_ref", "hclk";
+			power-domains = <&sysctrl>;
+			status = "disabled";
+
+			mii_conv1: mii-conv@1 {
+				reg = <1>;
+				status = "disabled";
+			};
+
+			mii_conv2: mii-conv@2 {
+				reg = <2>;
+				status = "disabled";
+			};
+
+			mii_conv3: mii-conv@3 {
+				reg = <3>;
+				status = "disabled";
+			};
+
+			mii_conv4: mii-conv@4 {
+				reg = <4>;
+				status = "disabled";
+			};
+
+			mii_conv5: mii-conv@5 {
+				reg = <5>;
+				status = "disabled";
+			};
+		};
+
+		switch: switch@44050000 {
+			compatible = "renesas,r9a06g032-a5psw", "renesas,rzn1-a5psw";
+			reg = <0x44050000 0x10000>;
+			clocks = <&sysctrl R9A06G032_HCLK_SWITCH>,
+				 <&sysctrl R9A06G032_CLK_SWITCH>;
+			clock-names = "hclk", "clk";
+			power-domains = <&sysctrl>;
+			status = "disabled";
+
+			ethernet-ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				switch_port0: port@0 {
+					reg = <0>;
+					pcs-handle = <&mii_conv5>;
+					status = "disabled";
+				};
+
+				switch_port1: port@1 {
+					reg = <1>;
+					pcs-handle = <&mii_conv4>;
+					status = "disabled";
+				};
+
+				switch_port2: port@2 {
+					reg = <2>;
+					pcs-handle = <&mii_conv3>;
+					status = "disabled";
+				};
+
+				switch_port3: port@3 {
+					reg = <3>;
+					pcs-handle = <&mii_conv2>;
+					status = "disabled";
+				};
+
+				switch_port4: port@4 {
+					reg = <4>;
+					ethernet = <&gmac2>;
+					label = "cpu";
+					phy-mode = "internal";
+					status = "disabled";
+					fixed-link {
+						speed = <1000>;
+						full-duplex;
+					};
+				};
+			};
+		};
+
 		gic: interrupt-controller@44101000 {
 			compatible = "arm,gic-400", "arm,cortex-a7-gic";
 			interrupt-controller;
@@ -184,11 +423,30 @@
 			interrupts =
 				<GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_HIGH)>;
 		};
+
+		can0: can@52104000 {
+			compatible = "renesas,r9a06g032-sja1000","renesas,rzn1-sja1000";
+			reg = <0x52104000 0x800>;
+			reg-io-width = <4>;
+			interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&sysctrl R9A06G032_HCLK_CAN0>;
+			power-domains = <&sysctrl>;
+			status = "disabled";
+		};
+
+		can1: can@52105000 {
+			compatible = "renesas,r9a06g032-sja1000", "renesas,rzn1-sja1000";
+			reg = <0x52105000 0x800>;
+			reg-io-width = <4>;
+			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&sysctrl R9A06G032_HCLK_CAN1>;
+			power-domains = <&sysctrl>;
+			status = "disabled";
+		};
 	};
 
 	timer {
-		compatible = "arm,cortex-a7-timer",
-			     "arm,armv7-timer";
+		compatible = "arm,armv7-timer";
 		interrupt-parent = <&gic>;
 		arm,cpu-registers-not-fw-configured;
 		always-on;
@@ -198,4 +456,10 @@
 			<GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
 			<GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>;
 	};
+
+	usbphy: usb-phy {
+		#phy-cells = <0>;
+		compatible = "usb-nop-xceiv";
+		status = "disabled";
+	};
 };
diff --git a/arch/arm/boot/dts/rk3036-evb.dts b/arch/arm/boot/dts/rk3036-evb.dts
index 2a7e6624efb9..9fd4d9db9f8f 100644
--- a/arch/arm/boot/dts/rk3036-evb.dts
+++ b/arch/arm/boot/dts/rk3036-evb.dts
@@ -15,16 +15,20 @@
 };
 
 &emac {
-	pinctrl-names = "default";
-	pinctrl-0 = <&emac_xfer>, <&emac_mdio>;
 	phy = <&phy0>;
-	phy-reset-gpios = <&gpio2 RK_PC6 GPIO_ACTIVE_LOW>; /* PHY_RST */
 	phy-reset-duration = <10>; /* millisecond */
-
+	phy-reset-gpios = <&gpio2 RK_PC6 GPIO_ACTIVE_LOW>; /* PHY_RST */
+	pinctrl-names = "default";
+	pinctrl-0 = <&emac_xfer>, <&emac_mdio>;
 	status = "okay";
 
-	phy0: ethernet-phy@0 {
-		reg = <0>;
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		phy0: ethernet-phy@0 {
+			reg = <0>;
+		};
 	};
 };
 
diff --git a/arch/arm/boot/dts/rk3036-kylin.dts b/arch/arm/boot/dts/rk3036-kylin.dts
index e817eba8c622..67e1e04139e7 100644
--- a/arch/arm/boot/dts/rk3036-kylin.dts
+++ b/arch/arm/boot/dts/rk3036-kylin.dts
@@ -80,16 +80,20 @@
 };
 
 &emac {
-	pinctrl-names = "default";
-	pinctrl-0 = <&emac_xfer>, <&emac_mdio>;
 	phy = <&phy0>;
-	phy-reset-gpios = <&gpio2 RK_PC6 GPIO_ACTIVE_LOW>; /* PHY_RST */
 	phy-reset-duration = <10>; /* millisecond */
-
+	phy-reset-gpios = <&gpio2 RK_PC6 GPIO_ACTIVE_LOW>; /* PHY_RST */
+	pinctrl-names = "default";
+	pinctrl-0 = <&emac_xfer>, <&emac_mdio>;
 	status = "okay";
 
-	phy0: ethernet-phy@0 {
-		reg = <0>;
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		phy0: ethernet-phy@0 {
+			reg = <0>;
+		};
 	};
 };
 
diff --git a/arch/arm/boot/dts/rk3036.dtsi b/arch/arm/boot/dts/rk3036.dtsi
index ba2b8891bbb7..78686fc72ce6 100644
--- a/arch/arm/boot/dts/rk3036.dtsi
+++ b/arch/arm/boot/dts/rk3036.dtsi
@@ -225,11 +225,9 @@
 	};
 
 	emac: ethernet@10200000 {
-		compatible = "rockchip,rk3036-emac", "snps,arc-emac";
+		compatible = "rockchip,rk3036-emac";
 		reg = <0x10200000 0x4000>;
 		interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
-		#address-cells = <1>;
-		#size-cells = <0>;
 		rockchip,grf = <&grf>;
 		clocks = <&cru HCLK_MAC>, <&cru SCLK_MACREF>, <&cru SCLK_MAC>;
 		clock-names = "hclk", "macref", "macclk";
@@ -330,6 +328,8 @@
 	cru: clock-controller@20000000 {
 		compatible = "rockchip,rk3036-cru";
 		reg = <0x20000000 0x1000>;
+		clocks = <&xin24m>;
+		clock-names = "xin24m";
 		rockchip,grf = <&grf>;
 		#clock-cells = <1>;
 		#reset-cells = <1>;
@@ -556,7 +556,7 @@
 		status = "disabled";
 	};
 
-	pdma: pdma@20078000 {
+	pdma: dma-controller@20078000 {
 		compatible = "arm,pl330", "arm,primecell";
 		reg = <0x20078000 0x4000>;
 		interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
@@ -614,7 +614,7 @@
 			#interrupt-cells = <2>;
 		};
 
-		pcfg_pull_default: pcfg_pull_default {
+		pcfg_pull_default: pcfg-pull-default {
 			bias-pull-pin-default;
 		};
 
diff --git a/arch/arm/boot/dts/rk3066a-bqcurie2.dts b/arch/arm/boot/dts/rk3066a-bqcurie2.dts
index 390aa33cd55a..962b4d1291db 100644
--- a/arch/arm/boot/dts/rk3066a-bqcurie2.dts
+++ b/arch/arm/boot/dts/rk3066a-bqcurie2.dts
@@ -48,7 +48,7 @@
 		compatible = "gpio-keys";
 		autorepeat;
 
-		power {
+		key-power {
 			gpios = <&gpio6 RK_PA2 GPIO_ACTIVE_LOW>; /* GPIO6_A2 */
 			linux,code = <KEY_POWER>;
 			label = "GPIO Key Power";
@@ -56,7 +56,7 @@
 			wakeup-source;
 			debounce-interval = <100>;
 		};
-		volume-down {
+		key-volume-down {
 			gpios = <&gpio4 RK_PC5 GPIO_ACTIVE_LOW>; /* GPIO4_C5 */
 			linux,code = <KEY_VOLUMEDOWN>;
 			label = "GPIO Key Vol-";
diff --git a/arch/arm/boot/dts/rk3066a-marsboard.dts b/arch/arm/boot/dts/rk3066a-marsboard.dts
index a66d915aa0f6..8beecd628282 100644
--- a/arch/arm/boot/dts/rk3066a-marsboard.dts
+++ b/arch/arm/boot/dts/rk3066a-marsboard.dts
@@ -150,18 +150,21 @@
 #include "tps65910.dtsi"
 
 &emac {
-	status = "okay";
-
 	phy = <&phy0>;
 	phy-supply = <&vcc_rmii>;
-
 	pinctrl-names = "default";
 	pinctrl-0 = <&emac_xfer>, <&emac_mdio>, <&phy_int>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
 
-	phy0: ethernet-phy@0 {
-		reg = <0>;
-		interrupt-parent = <&gpio1>;
-		interrupts = <RK_PD2 IRQ_TYPE_LEVEL_LOW>;
+		phy0: ethernet-phy@0 {
+			reg = <0>;
+			interrupt-parent = <&gpio1>;
+			interrupts = <RK_PD2 IRQ_TYPE_LEVEL_LOW>;
+		};
 	};
 };
 
diff --git a/arch/arm/boot/dts/rk3066a-mk808.dts b/arch/arm/boot/dts/rk3066a-mk808.dts
index 667d57a4ff45..cfa318a506eb 100644
--- a/arch/arm/boot/dts/rk3066a-mk808.dts
+++ b/arch/arm/boot/dts/rk3066a-mk808.dts
@@ -160,6 +160,24 @@
 	status = "okay";
 };
 
+&nfc {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	nand@0 {
+		reg = <0>;
+		label = "rk-nand";
+		nand-bus-width = <8>;
+		nand-ecc-mode = "hw";
+		nand-ecc-step-size = <1024>;
+		nand-ecc-strength = <40>;
+		nand-is-boot-medium;
+		rockchip,boot-blks = <8>;
+		rockchip,boot-ecc-strength = <24>;
+	};
+};
+
 &pinctrl {
 	usb-host {
 		host_drv: host-drv {
diff --git a/arch/arm/boot/dts/rk3066a-rayeager.dts b/arch/arm/boot/dts/rk3066a-rayeager.dts
index 12b2e59aebc4..3eee42137b6d 100644
--- a/arch/arm/boot/dts/rk3066a-rayeager.dts
+++ b/arch/arm/boot/dts/rk3066a-rayeager.dts
@@ -32,7 +32,7 @@
 	keys: gpio-keys {
 		compatible = "gpio-keys";
 
-		power {
+		key-power {
 			wakeup-source;
 			gpios = <&gpio6 RK_PA2 GPIO_ACTIVE_LOW>;
 			label = "GPIO Power";
@@ -142,15 +142,20 @@
 };
 
 &emac {
-	pinctrl-names = "default";
-	pinctrl-0 = <&emac_xfer>, <&emac_mdio>, <&rmii_rst>;
 	phy = <&phy0>;
 	phy-supply = <&vcc_rmii>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&emac_xfer>, <&emac_mdio>, <&rmii_rst>;
 	status = "okay";
 
-	phy0: ethernet-phy@0 {
-		reg = <0>;
-		reset-gpios = <&gpio1 RK_PD6 GPIO_ACTIVE_LOW>;
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		phy0: ethernet-phy@0 {
+			reg = <0>;
+			reset-gpios = <&gpio1 RK_PD6 GPIO_ACTIVE_LOW>;
+		};
 	};
 };
 
diff --git a/arch/arm/boot/dts/rk3066a.dtsi b/arch/arm/boot/dts/rk3066a.dtsi
index c25b9695db4b..de9915d946f7 100644
--- a/arch/arm/boot/dts/rk3066a.dtsi
+++ b/arch/arm/boot/dts/rk3066a.dtsi
@@ -202,8 +202,9 @@
 	cru: clock-controller@20000000 {
 		compatible = "rockchip,rk3066a-cru";
 		reg = <0x20000000 0x1000>;
+		clocks = <&xin24m>;
+		clock-names = "xin24m";
 		rockchip,grf = <&grf>;
-
 		#clock-cells = <1>;
 		#reset-cells = <1>;
 		assigned-clocks = <&cru PLL_CPLL>, <&cru PLL_GPLL>,
diff --git a/arch/arm/boot/dts/rk3188-bqedison2qc.dts b/arch/arm/boot/dts/rk3188-bqedison2qc.dts
index 85d3fce0142f..9312be362a7a 100644
--- a/arch/arm/boot/dts/rk3188-bqedison2qc.dts
+++ b/arch/arm/boot/dts/rk3188-bqedison2qc.dts
@@ -7,6 +7,7 @@
 /dts-v1/;
 #include <dt-bindings/i2c/i2c.h>
 #include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
 #include "rk3188.dtsi"
 
 / {
@@ -36,7 +37,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pwr_key &usb_int>;
 
-		power {
+		key-power {
 			gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
 			label = "GPIO Key Power";
@@ -45,7 +46,7 @@
 			wakeup-source;
 		};
 
-		wake_on_usb: wake-on-usb {
+		wake_on_usb: key-wake-on-usb {
 			label = "Wake-on-USB";
 			gpios = <&gpio0 RK_PA7 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_WAKEUP>;
@@ -485,7 +486,7 @@
 		reg = <1>;
 		compatible = "brcm,bcm4329-fmac";
 		interrupt-parent = <&gpio3>;
-		interrupts = <RK_PD2 GPIO_ACTIVE_HIGH>;
+		interrupts = <RK_PD2 IRQ_TYPE_NONE>;
 		interrupt-names = "host-wake";
 		brcm,drive-strength = <5>;
 		pinctrl-names = "default";
diff --git a/arch/arm/boot/dts/rk3188-px3-evb.dts b/arch/arm/boot/dts/rk3188-px3-evb.dts
index 39c60426c9c9..0a1ae689b162 100644
--- a/arch/arm/boot/dts/rk3188-px3-evb.dts
+++ b/arch/arm/boot/dts/rk3188-px3-evb.dts
@@ -29,7 +29,7 @@
 		compatible = "gpio-keys";
 		autorepeat;
 
-		power {
+		key-power {
 			gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
 			label = "GPIO Key Power";
@@ -212,7 +212,7 @@
 				regulator-name = "wl_18";
 			};
 
-			lcd_33: SWITCH_REG1 {
+			lcd_33: SWITCH_REG {
 				regulator-name = "lcd_33";
 			};
 		};
diff --git a/arch/arm/boot/dts/rk3188-radxarock.dts b/arch/arm/boot/dts/rk3188-radxarock.dts
index 36c0945f43b2..e7cf18823558 100644
--- a/arch/arm/boot/dts/rk3188-radxarock.dts
+++ b/arch/arm/boot/dts/rk3188-radxarock.dts
@@ -24,7 +24,7 @@
 		compatible = "gpio-keys";
 		autorepeat;
 
-		power {
+		key-power {
 			gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
 			label = "GPIO Key Power";
@@ -126,18 +126,21 @@
 };
 
 &emac {
-	status = "okay";
-
+	phy = <&phy0>;
+	phy-supply = <&vcc_rmii>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&emac_xfer>, <&emac_mdio>, <&phy_int>;
+	status = "okay";
 
-	phy = <&phy0>;
-	phy-supply = <&vcc_rmii>;
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
 
-	phy0: ethernet-phy@0 {
-		reg = <0>;
-		interrupt-parent = <&gpio3>;
-		interrupts = <RK_PD2 IRQ_TYPE_LEVEL_LOW>;
+		phy0: ethernet-phy@0 {
+			reg = <0>;
+			interrupt-parent = <&gpio3>;
+			interrupts = <RK_PD2 IRQ_TYPE_LEVEL_LOW>;
+		};
 	};
 };
 
diff --git a/arch/arm/boot/dts/rk3188.dtsi b/arch/arm/boot/dts/rk3188.dtsi
index a94321e90014..cdd4a0bd5133 100644
--- a/arch/arm/boot/dts/rk3188.dtsi
+++ b/arch/arm/boot/dts/rk3188.dtsi
@@ -195,8 +195,9 @@
 	cru: clock-controller@20000000 {
 		compatible = "rockchip,rk3188-cru";
 		reg = <0x20000000 0x1000>;
+		clocks = <&xin24m>;
+		clock-names = "xin24m";
 		rockchip,grf = <&grf>;
-
 		#clock-cells = <1>;
 		#reset-cells = <1>;
 	};
diff --git a/arch/arm/boot/dts/rk3229-evb.dts b/arch/arm/boot/dts/rk3229-evb.dts
index 797476e8bef1..5c3d08e3eea3 100644
--- a/arch/arm/boot/dts/rk3229-evb.dts
+++ b/arch/arm/boot/dts/rk3229-evb.dts
@@ -107,7 +107,7 @@
 		regulator-boot-on;
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 		autorepeat;
 		pinctrl-names = "default";
diff --git a/arch/arm/boot/dts/rk322x.dtsi b/arch/arm/boot/dts/rk322x.dtsi
index 8eed9e3a92e9..ffc16d6b97e1 100644
--- a/arch/arm/boot/dts/rk322x.dtsi
+++ b/arch/arm/boot/dts/rk322x.dtsi
@@ -484,6 +484,8 @@
 	cru: clock-controller@110e0000 {
 		compatible = "rockchip,rk3228-cru";
 		reg = <0x110e0000 0x1000>;
+		clocks = <&xin24m>;
+		clock-names = "xin24m";
 		rockchip,grf = <&grf>;
 		#clock-cells = <1>;
 		#reset-cells = <1>;
@@ -501,7 +503,7 @@
 			<75000000>;
 	};
 
-	pdma: pdma@110f0000 {
+	pdma: dma-controller@110f0000 {
 		compatible = "arm,pl330", "arm,primecell";
 		reg = <0x110f0000 0x4000>;
 		interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
@@ -718,8 +720,8 @@
 		interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
 		assigned-clocks = <&cru SCLK_HDMI_PHY>;
 		assigned-clock-parents = <&hdmi_phy>;
-		clocks = <&cru SCLK_HDMI_HDCP>, <&cru PCLK_HDMI_CTRL>, <&cru SCLK_HDMI_CEC>;
-		clock-names = "isfr", "iahb", "cec";
+		clocks = <&cru PCLK_HDMI_CTRL>, <&cru SCLK_HDMI_HDCP>, <&cru SCLK_HDMI_CEC>;
+		clock-names = "iahb", "isfr", "cec";
 		pinctrl-names = "default";
 		pinctrl-0 = <&hdmii2c_xfer &hdmi_hpd &hdmi_cec>;
 		resets = <&cru SRST_HDMI_P>;
diff --git a/arch/arm/boot/dts/rk3288-evb.dtsi b/arch/arm/boot/dts/rk3288-evb.dtsi
index c4ca73b40d4a..399d6b9c5fd4 100644
--- a/arch/arm/boot/dts/rk3288-evb.dtsi
+++ b/arch/arm/boot/dts/rk3288-evb.dtsi
@@ -118,7 +118,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pwrbtn>;
 
-		power {
+		key-power {
 			gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
 			label = "GPIO Key Power";
diff --git a/arch/arm/boot/dts/rk3288-firefly-reload.dts b/arch/arm/boot/dts/rk3288-firefly-reload.dts
index 9a4a9749c405..a5a0826341e6 100644
--- a/arch/arm/boot/dts/rk3288-firefly-reload.dts
+++ b/arch/arm/boot/dts/rk3288-firefly-reload.dts
@@ -27,7 +27,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		power {
+		key-power {
 			wakeup-source;
 			gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_LOW>;
 			label = "GPIO Power";
diff --git a/arch/arm/boot/dts/rk3288-firefly.dtsi b/arch/arm/boot/dts/rk3288-firefly.dtsi
index 7fb582302b32..052afe5543e2 100644
--- a/arch/arm/boot/dts/rk3288-firefly.dtsi
+++ b/arch/arm/boot/dts/rk3288-firefly.dtsi
@@ -49,7 +49,7 @@
 	keys: gpio-keys {
 		compatible = "gpio-keys";
 
-		power {
+		key-power {
 			wakeup-source;
 			gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_LOW>;
 			label = "GPIO Power";
diff --git a/arch/arm/boot/dts/rk3288-phycore-rdk.dts b/arch/arm/boot/dts/rk3288-phycore-rdk.dts
index 1e33859de484..1a5156951492 100644
--- a/arch/arm/boot/dts/rk3288-phycore-rdk.dts
+++ b/arch/arm/boot/dts/rk3288-phycore-rdk.dts
@@ -20,14 +20,14 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&user_button_pins>;
 
-		button@0 {
+		button-0 {
 			label = "home";
 			linux,code = <KEY_HOME>;
 			gpios = <&gpio8 0 GPIO_ACTIVE_HIGH>;
 			wakeup-source;
 		};
 
-		button@1 {
+		button-1 {
 			label = "menu";
 			linux,code = <KEY_MENU>;
 			gpios = <&gpio8 3 GPIO_ACTIVE_HIGH>;
diff --git a/arch/arm/boot/dts/rk3288-popmetal.dts b/arch/arm/boot/dts/rk3288-popmetal.dts
index 8c7376d64bc4..fd90f3b8fc32 100644
--- a/arch/arm/boot/dts/rk3288-popmetal.dts
+++ b/arch/arm/boot/dts/rk3288-popmetal.dts
@@ -30,7 +30,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pwrbtn>;
 
-		power {
+		key-power {
 			gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
 			label = "GPIO Key Power";
diff --git a/arch/arm/boot/dts/rk3288-r89.dts b/arch/arm/boot/dts/rk3288-r89.dts
index 55467bc30fa6..633e5a032463 100644
--- a/arch/arm/boot/dts/rk3288-r89.dts
+++ b/arch/arm/boot/dts/rk3288-r89.dts
@@ -31,7 +31,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pwrbtn>;
 
-		power {
+		key-power {
 			gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
 			label = "GPIO Key Power";
diff --git a/arch/arm/boot/dts/rk3288-rock2-square.dts b/arch/arm/boot/dts/rk3288-rock2-square.dts
index c4d1d142d8c6..80e0f07c8e87 100644
--- a/arch/arm/boot/dts/rk3288-rock2-square.dts
+++ b/arch/arm/boot/dts/rk3288-rock2-square.dts
@@ -28,7 +28,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		power {
+		key-power {
 			gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_LOW>;
 			label = "GPIO Power";
 			linux,code = <KEY_POWER>;
diff --git a/arch/arm/boot/dts/rk3288-tinker.dtsi b/arch/arm/boot/dts/rk3288-tinker.dtsi
index 9c1e38c54eae..09618bb7d872 100644
--- a/arch/arm/boot/dts/rk3288-tinker.dtsi
+++ b/arch/arm/boot/dts/rk3288-tinker.dtsi
@@ -26,14 +26,12 @@
 
 	gpio-keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		autorepeat;
 
 		pinctrl-names = "default";
 		pinctrl-0 = <&pwrbtn>;
 
-		button@0 {
+		button {
 			gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
 			label = "GPIO Key Power";
diff --git a/arch/arm/boot/dts/rk3288-veyron-broadcom-bluetooth.dtsi b/arch/arm/boot/dts/rk3288-veyron-broadcom-bluetooth.dtsi
index a10d25ac8f7b..f9dde0eef527 100644
--- a/arch/arm/boot/dts/rk3288-veyron-broadcom-bluetooth.dtsi
+++ b/arch/arm/boot/dts/rk3288-veyron-broadcom-bluetooth.dtsi
@@ -13,10 +13,10 @@
 			    <&bt_dev_wake>;
 
 		compatible = "brcm,bcm43540-bt";
-		host-wakeup-gpios	= <&gpio4 RK_PD7 GPIO_ACTIVE_HIGH>;
-		shutdown-gpios		= <&gpio4 RK_PD5 GPIO_ACTIVE_HIGH>;
-		device-wakeup-gpios	= <&gpio4 RK_PD2 GPIO_ACTIVE_HIGH>;
-		max-speed		= <3000000>;
-		brcm,bt-pcm-int-params	= [01 02 00 01 01];
+		host-wakeup-gpios = <&gpio4 RK_PD7 GPIO_ACTIVE_HIGH>;
+		shutdown-gpios = <&gpio4 RK_PD5 GPIO_ACTIVE_HIGH>;
+		device-wakeup-gpios = <&gpio4 RK_PD2 GPIO_ACTIVE_HIGH>;
+		max-speed = <3000000>;
+		brcm,bt-pcm-int-params = [01 02 00 01 01];
 	};
 };
diff --git a/arch/arm/boot/dts/rk3288-veyron-chromebook.dtsi b/arch/arm/boot/dts/rk3288-veyron-chromebook.dtsi
index 05112c25176d..700bb548d6b2 100644
--- a/arch/arm/boot/dts/rk3288-veyron-chromebook.dtsi
+++ b/arch/arm/boot/dts/rk3288-veyron-chromebook.dtsi
@@ -32,7 +32,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&ap_lid_int_l>;
 
-		lid {
+		switch-lid {
 			label = "Lid";
 			gpios = <&gpio0 RK_PA6 GPIO_ACTIVE_LOW>;
 			wakeup-source;
diff --git a/arch/arm/boot/dts/rk3288-veyron-minnie.dts b/arch/arm/boot/dts/rk3288-veyron-minnie.dts
index 82fc6fba9999..dcdcc55c4098 100644
--- a/arch/arm/boot/dts/rk3288-veyron-minnie.dts
+++ b/arch/arm/boot/dts/rk3288-veyron-minnie.dts
@@ -21,14 +21,14 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&volum_down_l &volum_up_l>;
 
-		volum_down {
+		key-volum-down {
 			label = "Volum_down";
 			gpios = <&gpio5 RK_PB3 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_VOLUMEDOWN>;
 			debounce-interval = <100>;
 		};
 
-		volum_up {
+		key-volum-up {
 			label = "Volum_up";
 			gpios = <&gpio5 RK_PB2 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_VOLUMEUP>;
diff --git a/arch/arm/boot/dts/rk3288-veyron-pinky.dts b/arch/arm/boot/dts/rk3288-veyron-pinky.dts
index 4e9fdb0f722d..e2a4e6232eb5 100644
--- a/arch/arm/boot/dts/rk3288-veyron-pinky.dts
+++ b/arch/arm/boot/dts/rk3288-veyron-pinky.dts
@@ -45,7 +45,7 @@
 &lid_switch {
 	pinctrl-0 = <&pwr_key_h &ap_lid_int_l>;
 
-	power {
+	key-power {
 		gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_HIGH>;
 	};
 };
diff --git a/arch/arm/boot/dts/rk3288-veyron.dtsi b/arch/arm/boot/dts/rk3288-veyron.dtsi
index 54a6838d73f5..e406c8c7c7e5 100644
--- a/arch/arm/boot/dts/rk3288-veyron.dtsi
+++ b/arch/arm/boot/dts/rk3288-veyron.dtsi
@@ -29,7 +29,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pwr_key_l>;
 
-		power {
+		key-power {
 			label = "Power";
 			gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
diff --git a/arch/arm/boot/dts/rk3288.dtsi b/arch/arm/boot/dts/rk3288.dtsi
index aaaa61875701..487b0e03d4b4 100644
--- a/arch/arm/boot/dts/rk3288.dtsi
+++ b/arch/arm/boot/dts/rk3288.dtsi
@@ -862,6 +862,8 @@
 	cru: clock-controller@ff760000 {
 		compatible = "rockchip,rk3288-cru";
 		reg = <0x0 0xff760000 0x0 0x1000>;
+		clocks = <&xin24m>;
+		clock-names = "xin24m";
 		rockchip,grf = <&grf>;
 		#clock-cells = <1>;
 		#reset-cells = <1>;
@@ -971,7 +973,7 @@
 		status = "disabled";
 	};
 
-	crypto: cypto-controller@ff8a0000 {
+	crypto: crypto@ff8a0000 {
 		compatible = "rockchip,rk3288-crypto";
 		reg = <0x0 0xff8a0000 0x0 0x4000>;
 		interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>;
@@ -980,7 +982,6 @@
 		clock-names = "aclk", "hclk", "sclk", "apb_pclk";
 		resets = <&cru SRST_CRYPTO>;
 		reset-names = "crypto-rst";
-		status = "okay";
 	};
 
 	iep_mmu: iommu@ff900800 {
diff --git a/arch/arm/boot/dts/rk3xxx.dtsi b/arch/arm/boot/dts/rk3xxx.dtsi
index 616a828e0c6e..bf285091a9eb 100644
--- a/arch/arm/boot/dts/rk3xxx.dtsi
+++ b/arch/arm/boot/dts/rk3xxx.dtsi
@@ -186,8 +186,6 @@
 		compatible = "snps,arc-emac";
 		reg = <0x10204000 0x3c>;
 		interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
-		#address-cells = <1>;
-		#size-cells = <0>;
 
 		rockchip,grf = <&grf>;
 
diff --git a/arch/arm/boot/dts/rv1108-elgin-r1.dts b/arch/arm/boot/dts/rv1108-elgin-r1.dts
index f62c9f7af79d..2d9994379eb2 100644
--- a/arch/arm/boot/dts/rv1108-elgin-r1.dts
+++ b/arch/arm/boot/dts/rv1108-elgin-r1.dts
@@ -72,6 +72,7 @@
 		interrupt-parent = <&gpio0>;
 		interrupts = <RK_PB4 IRQ_TYPE_LEVEL_LOW>;
 		rockchip,system-power-controller;
+		#clock-cells = <0>;
 
 		vcc1-supply = <&vcc_sys>;
 		vcc2-supply = <&vcc_sys>;
@@ -82,7 +83,7 @@
 
 		regulators {
 			vdd_core: DCDC_REG1 {
-				regulator-name= "vdd_core";
+				regulator-name = "vdd_core";
 				regulator-min-microvolt = <700000>;
 				regulator-max-microvolt = <1500000>;
 				regulator-always-on;
@@ -94,7 +95,7 @@
 			};
 
 			vdd_buck2: DCDC_REG2 {
-				regulator-name= "vdd_buck2";
+				regulator-name = "vdd_buck2";
 				regulator-min-microvolt = <2200000>;
 				regulator-max-microvolt = <2200000>;
 				regulator-always-on;
@@ -105,7 +106,7 @@
 			};
 
 			vcc_ddr: DCDC_REG3 {
-				regulator-name= "vcc_ddr";
+				regulator-name = "vcc_ddr";
 				regulator-always-on;
 				regulator-boot-on;
 				regulator-state-mem {
@@ -114,7 +115,7 @@
 			};
 
 			vcc_io: DCDC_REG4 {
-				regulator-name= "vcc_io";
+				regulator-name = "vcc_io";
 				regulator-min-microvolt = <3300000>;
 				regulator-max-microvolt = <3300000>;
 				regulator-always-on;
@@ -126,7 +127,7 @@
 			};
 
 			vdd_10: LDO_REG1 {
-				regulator-name= "vdd_10";
+				regulator-name = "vdd_10";
 				regulator-min-microvolt = <1000000>;
 				regulator-max-microvolt = <1000000>;
 				regulator-always-on;
@@ -137,7 +138,7 @@
 			};
 
 			vcc_18: LDO_REG2 {
-				regulator-name= "vcc_18";
+				regulator-name = "vcc_18";
 				regulator-min-microvolt = <1800000>;
 				regulator-max-microvolt = <1800000>;
 				regulator-always-on;
@@ -148,7 +149,7 @@
 			};
 
 			vdd10_pmu: LDO_REG3 {
-				regulator-name= "vdd10_pmu";
+				regulator-name = "vdd10_pmu";
 				regulator-min-microvolt = <1000000>;
 				regulator-max-microvolt = <1000000>;
 				regulator-always-on;
diff --git a/arch/arm/boot/dts/rv1108-evb.dts b/arch/arm/boot/dts/rv1108-evb.dts
index fe5fc9bf75c9..ef150f4ee99d 100644
--- a/arch/arm/boot/dts/rv1108-evb.dts
+++ b/arch/arm/boot/dts/rv1108-evb.dts
@@ -85,6 +85,7 @@
 		interrupt-parent = <&gpio0>;
 		interrupts = <RK_PB4 IRQ_TYPE_LEVEL_LOW>;
 		rockchip,system-power-controller;
+		#clock-cells = <0>;
 
 		vcc1-supply = <&vcc_sys>;
 		vcc2-supply = <&vcc_sys>;
@@ -95,7 +96,7 @@
 
 		regulators {
 			vdd_core: DCDC_REG1 {
-				regulator-name= "vdd_core";
+				regulator-name = "vdd_core";
 				regulator-min-microvolt = <700000>;
 				regulator-max-microvolt = <1500000>;
 				regulator-always-on;
@@ -107,7 +108,7 @@
 			};
 
 			vdd_cam: DCDC_REG2 {
-				regulator-name= "vdd_cam";
+				regulator-name = "vdd_cam";
 				regulator-min-microvolt = <700000>;
 				regulator-max-microvolt = <2000000>;
 				regulator-state-mem {
@@ -116,7 +117,7 @@
 			};
 
 			vcc_ddr: DCDC_REG3 {
-				regulator-name= "vcc_ddr";
+				regulator-name = "vcc_ddr";
 				regulator-always-on;
 				regulator-boot-on;
 				regulator-state-mem {
@@ -125,7 +126,7 @@
 			};
 
 			vcc_io: DCDC_REG4 {
-				regulator-name= "vcc_io";
+				regulator-name = "vcc_io";
 				regulator-min-microvolt = <3300000>;
 				regulator-max-microvolt = <3300000>;
 				regulator-always-on;
@@ -137,7 +138,7 @@
 			};
 
 			vdd_10: LDO_REG1 {
-				regulator-name= "vdd_10";
+				regulator-name = "vdd_10";
 				regulator-min-microvolt = <1000000>;
 				regulator-max-microvolt = <1000000>;
 				regulator-always-on;
@@ -148,7 +149,7 @@
 			};
 
 			vcc_18: LDO_REG2 {
-				regulator-name= "vcc_18";
+				regulator-name = "vcc_18";
 				regulator-min-microvolt = <1800000>;
 				regulator-max-microvolt = <1800000>;
 				regulator-always-on;
@@ -159,7 +160,7 @@
 			};
 
 			vdd10_pmu: LDO_REG3 {
-				regulator-name= "vdd10_pmu";
+				regulator-name = "vdd10_pmu";
 				regulator-min-microvolt = <1000000>;
 				regulator-max-microvolt = <1000000>;
 				regulator-always-on;
diff --git a/arch/arm/boot/dts/rv1108.dtsi b/arch/arm/boot/dts/rv1108.dtsi
index 448254906452..abf3006f0a84 100644
--- a/arch/arm/boot/dts/rv1108.dtsi
+++ b/arch/arm/boot/dts/rv1108.dtsi
@@ -85,24 +85,6 @@
 		#clock-cells = <0>;
 	};
 
-	amba: bus {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-
-		pdma: pdma@102a0000 {
-			compatible = "arm,pl330", "arm,primecell";
-			reg = <0x102a0000 0x4000>;
-			interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
-			#dma-cells = <1>;
-			arm,pl330-broken-no-flushp;
-			arm,pl330-periph-burst;
-			clocks = <&cru ACLK_DMAC>;
-			clock-names = "apb_pclk";
-		};
-	};
-
 	bus_intmem: sram@10080000 {
 		compatible = "mmio-sram";
 		reg = <0x10080000 0x2000>;
@@ -259,6 +241,17 @@
 		status = "disabled";
 	};
 
+	pdma: dma-controller@102a0000 {
+		compatible = "arm,pl330", "arm,primecell";
+		reg = <0x102a0000 0x4000>;
+		interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
+		#dma-cells = <1>;
+		arm,pl330-broken-no-flushp;
+		arm,pl330-periph-burst;
+		clocks = <&cru ACLK_DMAC>;
+		clock-names = "apb_pclk";
+	};
+
 	grf: syscon@10300000 {
 		compatible = "rockchip,rv1108-grf", "syscon", "simple-mfd";
 		reg = <0x10300000 0x1000>;
@@ -456,6 +449,8 @@
 	cru: clock-controller@20200000 {
 		compatible = "rockchip,rv1108-cru";
 		reg = <0x20200000 0x1000>;
+		clocks = <&xin24m>;
+		clock-names = "xin24m";
 		rockchip,grf = <&grf>;
 		#clock-cells = <1>;
 		#reset-cells = <1>;
@@ -753,7 +748,7 @@
 
 		gmac {
 			rmii_pins: rmii-pins {
-				rockchip,pins =	<1 RK_PC5 2 &pcfg_pull_none>,
+				rockchip,pins = <1 RK_PC5 2 &pcfg_pull_none>,
 						<1 RK_PC3 2 &pcfg_pull_none>,
 						<1 RK_PC4 2 &pcfg_pull_none>,
 						<1 RK_PB2 3 &pcfg_pull_none_drv_12ma>,
diff --git a/arch/arm/boot/dts/s3c2410-pinctrl.h b/arch/arm/boot/dts/s3c2410-pinctrl.h
new file mode 100644
index 000000000000..76b6171ae149
--- /dev/null
+++ b/arch/arm/boot/dts/s3c2410-pinctrl.h
@@ -0,0 +1,19 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Samsung S3C2410 DTS pinctrl constants
+ *
+ * Copyright (c) 2016 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
+ * Copyright (c) 2022 Linaro Ltd
+ * Author: Krzysztof Kozlowski <krzk@kernel.org>
+ */
+
+#ifndef __DTS_ARM_SAMSUNG_S3C2410_PINCTRL_H__
+#define __DTS_ARM_SAMSUNG_S3C2410_PINCTRL_H__
+
+#define S3C2410_PIN_FUNC_INPUT		0
+#define S3C2410_PIN_FUNC_OUTPUT		1
+#define S3C2410_PIN_FUNC_2		2
+#define S3C2410_PIN_FUNC_3		3
+
+#endif /* __DTS_ARM_SAMSUNG_S3C2410_PINCTRL_H__ */
diff --git a/arch/arm/boot/dts/s3c2416-pinctrl.dtsi b/arch/arm/boot/dts/s3c2416-pinctrl.dtsi
index 92439ee5d7de..3268366bd8bc 100644
--- a/arch/arm/boot/dts/s3c2416-pinctrl.dtsi
+++ b/arch/arm/boot/dts/s3c2416-pinctrl.dtsi
@@ -5,73 +5,73 @@
  * Copyright (c) 2013 Heiko Stuebner <heiko@sntech.de>
  */
 
-#include <dt-bindings/pinctrl/samsung.h>
+#include "s3c2410-pinctrl.h"
 
 &pinctrl_0 {
 	/*
 	 * Pin banks
 	 */
 
-	gpa: gpa {
+	gpa: gpa-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpb: gpb {
+	gpb: gpb-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpc: gpc {
+	gpc: gpc-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpd: gpd {
+	gpd: gpd-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpe: gpe {
+	gpe: gpe-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpf: gpf {
+	gpf: gpf-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 		interrupt-controller;
 		#interrupt-cells = <2>;
 	};
 
-	gpg: gpg {
+	gpg: gpg-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 		interrupt-controller;
 		#interrupt-cells = <2>;
 	};
 
-	gph: gph {
+	gph: gph-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpj: gpj {
+	gpj: gpj-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpk: gpk {
+	gpk: gpk-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpl: gpl {
+	gpl: gpl-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpm: gpm {
+	gpm: gpm-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
@@ -80,93 +80,93 @@
 	 * Pin groups
 	 */
 
-	uart0_data: uart0-data {
+	uart0_data: uart0-data-pins {
 		samsung,pins = "gph-0", "gph-1";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C2410_PIN_FUNC_2>;
 	};
 
-	uart0_fctl: uart0-fctl {
+	uart0_fctl: uart0-fctl-pins {
 		samsung,pins = "gph-8", "gph-9";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C2410_PIN_FUNC_2>;
 	};
 
-	uart1_data: uart1-data {
+	uart1_data: uart1-data-pins {
 		samsung,pins = "gph-2", "gph-3";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C2410_PIN_FUNC_2>;
 	};
 
-	uart1_fctl: uart1-fctl {
+	uart1_fctl: uart1-fctl-pins {
 		samsung,pins = "gph-10", "gph-11";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C2410_PIN_FUNC_2>;
 	};
 
-	uart2_data: uart2-data {
+	uart2_data: uart2-data-pins {
 		samsung,pins = "gph-4", "gph-5";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C2410_PIN_FUNC_2>;
 	};
 
-	uart2_fctl: uart2-fctl {
+	uart2_fctl: uart2-fctl-pins {
 		samsung,pins = "gph-6", "gph-7";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C2410_PIN_FUNC_2>;
 	};
 
-	uart3_data: uart3-data {
+	uart3_data: uart3-data-pins {
 		samsung,pins = "gph-6", "gph-7";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C2410_PIN_FUNC_2>;
 	};
 
-	extuart_clk: extuart-clk {
+	extuart_clk: extuart-clk-pins {
 		samsung,pins = "gph-12";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C2410_PIN_FUNC_2>;
 	};
 
-	i2c0_bus: i2c0-bus {
+	i2c0_bus: i2c0-bus-pins {
 		samsung,pins = "gpe-14", "gpe-15";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C2410_PIN_FUNC_2>;
 	};
 
-	spi0_bus: spi0-bus {
+	spi0_bus: spi0-bus-pins {
 		samsung,pins = "gpe-11", "gpe-12", "gpe-13";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C2410_PIN_FUNC_2>;
 	};
 
-	sd0_clk: sd0-clk {
+	sd0_clk: sd0-clk-pins {
 		samsung,pins = "gpe-5";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C2410_PIN_FUNC_2>;
 	};
 
-	sd0_cmd: sd0-cmd {
+	sd0_cmd: sd0-cmd-pins {
 		samsung,pins = "gpe-6";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C2410_PIN_FUNC_2>;
 	};
 
-	sd0_bus1: sd0-bus1 {
+	sd0_bus1: sd0-bus1-pins {
 		samsung,pins = "gpe-7";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C2410_PIN_FUNC_2>;
 	};
 
-	sd0_bus4: sd0-bus4 {
+	sd0_bus4: sd0-bus4-pins {
 		samsung,pins = "gpe-8", "gpe-9", "gpe-10";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C2410_PIN_FUNC_2>;
 	};
 
-	sd1_cmd: sd1-cmd {
+	sd1_cmd: sd1-cmd-pins {
 		samsung,pins = "gpl-8";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C2410_PIN_FUNC_2>;
 	};
 
-	sd1_clk: sd1-clk {
+	sd1_clk: sd1-clk-pins {
 		samsung,pins = "gpl-9";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C2410_PIN_FUNC_2>;
 	};
 
-	sd1_bus1: sd1-bus1 {
+	sd1_bus1: sd1-bus1-pins {
 		samsung,pins = "gpl-0";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C2410_PIN_FUNC_2>;
 	};
 
-	sd1_bus4: sd1-bus4 {
+	sd1_bus4: sd1-bus4-pins {
 		samsung,pins = "gpl-1", "gpl-2", "gpl-3";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C2410_PIN_FUNC_2>;
 	};
 };
diff --git a/arch/arm/boot/dts/s3c2416.dtsi b/arch/arm/boot/dts/s3c2416.dtsi
index 4f084f4fe44f..4660751cb207 100644
--- a/arch/arm/boot/dts/s3c2416.dtsi
+++ b/arch/arm/boot/dts/s3c2416.dtsi
@@ -45,7 +45,7 @@
 		status = "disabled";
 	};
 
-	sdhci_1: sdhci@4ac00000 {
+	sdhci_1: mmc@4ac00000 {
 		compatible = "samsung,s3c6410-sdhci";
 		reg = <0x4AC00000 0x100>;
 		interrupts = <0 0 21 3>;
@@ -56,7 +56,7 @@
 		status = "disabled";
 	};
 
-	sdhci_0: sdhci@4a800000 {
+	sdhci_0: mmc@4a800000 {
 		compatible = "samsung,s3c6410-sdhci";
 		reg = <0x4A800000 0x100>;
 		interrupts = <0 0 20 3>;
diff --git a/arch/arm/boot/dts/s3c6410-mini6410.dts b/arch/arm/boot/dts/s3c6410-mini6410.dts
index 285555b9ed94..17097da36f5e 100644
--- a/arch/arm/boot/dts/s3c6410-mini6410.dts
+++ b/arch/arm/boot/dts/s3c6410-mini6410.dts
@@ -193,12 +193,12 @@
 };
 
 &pinctrl0 {
-	gpio_leds: gpio-leds {
+	gpio_leds: gpio-leds-pins {
 		samsung,pins = "gpk-4", "gpk-5", "gpk-6", "gpk-7";
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	gpio_keys: gpio-keys {
+	gpio_keys: gpio-keys-pins {
 		samsung,pins = "gpn-0", "gpn-1", "gpn-2", "gpn-3",
 				"gpn-4", "gpn-5", "gpl-11", "gpl-12";
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
diff --git a/arch/arm/boot/dts/s3c64xx-pinctrl.dtsi b/arch/arm/boot/dts/s3c64xx-pinctrl.dtsi
index 8e9594d64b57..f53959b7d031 100644
--- a/arch/arm/boot/dts/s3c64xx-pinctrl.dtsi
+++ b/arch/arm/boot/dts/s3c64xx-pinctrl.dtsi
@@ -9,118 +9,118 @@
  * listed as device tree nodes in this file.
  */
 
-#include <dt-bindings/pinctrl/samsung.h>
+#include "s3c64xx-pinctrl.h"
 
 &pinctrl0 {
 	/*
 	 * Pin banks
 	 */
 
-	gpa: gpa {
+	gpa: gpa-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 		interrupt-controller;
 		#interrupt-cells = <2>;
 	};
 
-	gpb: gpb {
+	gpb: gpb-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 		interrupt-controller;
 		#interrupt-cells = <2>;
 	};
 
-	gpc: gpc {
+	gpc: gpc-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 		interrupt-controller;
 		#interrupt-cells = <2>;
 	};
 
-	gpd: gpd {
+	gpd: gpd-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 		interrupt-controller;
 		#interrupt-cells = <2>;
 	};
 
-	gpe: gpe {
+	gpe: gpe-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpf: gpf {
+	gpf: gpf-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 		interrupt-controller;
 		#interrupt-cells = <2>;
 	};
 
-	gpg: gpg {
+	gpg: gpg-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 		interrupt-controller;
 		#interrupt-cells = <2>;
 	};
 
-	gph: gph {
+	gph: gph-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 		interrupt-controller;
 		#interrupt-cells = <2>;
 	};
 
-	gpi: gpi {
+	gpi: gpi-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpj: gpj {
+	gpj: gpj-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpk: gpk {
+	gpk: gpk-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gpl: gpl {
+	gpl: gpl-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 		interrupt-controller;
 		#interrupt-cells = <2>;
 	};
 
-	gpm: gpm {
+	gpm: gpm-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 		interrupt-controller;
 		#interrupt-cells = <2>;
 	};
 
-	gpn: gpn {
+	gpn: gpn-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 		interrupt-controller;
 		#interrupt-cells = <2>;
 	};
 
-	gpo: gpo {
+	gpo: gpo-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 		interrupt-controller;
 		#interrupt-cells = <2>;
 	};
 
-	gpp: gpp {
+	gpp: gpp-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 		interrupt-controller;
 		#interrupt-cells = <2>;
 	};
 
-	gpq: gpq {
+	gpq: gpq-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 		interrupt-controller;
@@ -131,552 +131,552 @@
 	 * Pin groups
 	 */
 
-	uart0_data: uart0-data {
+	uart0_data: uart0-data-pins {
 		samsung,pins = "gpa-0", "gpa-1";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	uart0_fctl: uart0-fctl {
+	uart0_fctl: uart0-fctl-pins {
 		samsung,pins = "gpa-2", "gpa-3";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	uart1_data: uart1-data {
+	uart1_data: uart1-data-pins {
 		samsung,pins = "gpa-4", "gpa-5";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	uart1_fctl: uart1-fctl {
+	uart1_fctl: uart1-fctl-pins {
 		samsung,pins = "gpa-6", "gpa-7";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	uart2_data: uart2-data {
+	uart2_data: uart2-data-pins {
 		samsung,pins = "gpb-0", "gpb-1";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	uart3_data: uart3-data {
+	uart3_data: uart3-data-pins {
 		samsung,pins = "gpb-2", "gpb-3";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	ext_dma_0: ext-dma-0 {
+	ext_dma_0: ext-dma-0-pins {
 		samsung,pins = "gpb-0", "gpb-1";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	ext_dma_1: ext-dma-1 {
+	ext_dma_1: ext-dma-1-pins {
 		samsung,pins = "gpb-2", "gpb-3";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_4>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	irda_data_0: irda-data-0 {
+	irda_data_0: irda-data-0-pins {
 		samsung,pins = "gpb-0", "gpb-1";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_4>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	irda_data_1: irda-data-1 {
+	irda_data_1: irda-data-1-pins {
 		samsung,pins = "gpb-2", "gpb-3";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	irda_sdbw: irda-sdbw {
+	irda_sdbw: irda-sdbw-pins {
 		samsung,pins = "gpb-4";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	i2c0_bus: i2c0-bus {
+	i2c0_bus: i2c0-bus-pins {
 		samsung,pins = "gpb-5", "gpb-6";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_UP>;
 	};
 
-	i2c1_bus: i2c1-bus {
+	i2c1_bus: i2c1-bus-pins {
 		/* S3C6410-only */
 		samsung,pins = "gpb-2", "gpb-3";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_6>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_6>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_UP>;
 	};
 
-	spi0_bus: spi0-bus {
+	spi0_bus: spi0-bus-pins {
 		samsung,pins = "gpc-0", "gpc-1", "gpc-2";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_UP>;
 	};
 
-	spi0_cs: spi0-cs {
+	spi0_cs: spi0-cs-pins {
 		samsung,pins = "gpc-3";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	spi1_bus: spi1-bus {
+	spi1_bus: spi1-bus-pins {
 		samsung,pins = "gpc-4", "gpc-5", "gpc-6";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_UP>;
 	};
 
-	spi1_cs: spi1-cs {
+	spi1_cs: spi1-cs-pins {
 		samsung,pins = "gpc-7";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	sd0_cmd: sd0-cmd {
+	sd0_cmd: sd0-cmd-pins {
 		samsung,pins = "gpg-1";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	sd0_clk: sd0-clk {
+	sd0_clk: sd0-clk-pins {
 		samsung,pins = "gpg-0";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	sd0_bus1: sd0-bus1 {
+	sd0_bus1: sd0-bus1-pins {
 		samsung,pins = "gpg-2";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	sd0_bus4: sd0-bus4 {
+	sd0_bus4: sd0-bus4-pins {
 		samsung,pins = "gpg-2", "gpg-3", "gpg-4", "gpg-5";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	sd0_cd: sd0-cd {
+	sd0_cd: sd0-cd-pins {
 		samsung,pins = "gpg-6";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_UP>;
 	};
 
-	sd1_cmd: sd1-cmd {
+	sd1_cmd: sd1-cmd-pins {
 		samsung,pins = "gph-1";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	sd1_clk: sd1-clk {
+	sd1_clk: sd1-clk-pins {
 		samsung,pins = "gph-0";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	sd1_bus1: sd1-bus1 {
+	sd1_bus1: sd1-bus1-pins {
 		samsung,pins = "gph-2";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	sd1_bus4: sd1-bus4 {
+	sd1_bus4: sd1-bus4-pins {
 		samsung,pins = "gph-2", "gph-3", "gph-4", "gph-5";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	sd1_bus8: sd1-bus8 {
+	sd1_bus8: sd1-bus8-pins {
 		samsung,pins = "gph-2", "gph-3", "gph-4", "gph-5",
 				"gph-6", "gph-7", "gph-8", "gph-9";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	sd1_cd: sd1-cd {
+	sd1_cd: sd1-cd-pins {
 		samsung,pins = "gpg-6";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_UP>;
 	};
 
-	sd2_cmd: sd2-cmd {
+	sd2_cmd: sd2-cmd-pins {
 		samsung,pins = "gpc-4";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	sd2_clk: sd2-clk {
+	sd2_clk: sd2-clk-pins {
 		samsung,pins = "gpc-5";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	sd2_bus1: sd2-bus1 {
+	sd2_bus1: sd2-bus1-pins {
 		samsung,pins = "gph-6";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	sd2_bus4: sd2-bus4 {
+	sd2_bus4: sd2-bus4-pins {
 		samsung,pins = "gph-6", "gph-7", "gph-8", "gph-9";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	i2s0_bus: i2s0-bus {
+	i2s0_bus: i2s0-bus-pins {
 		samsung,pins = "gpd-0", "gpd-2", "gpd-3", "gpd-4";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	i2s0_cdclk: i2s0-cdclk {
+	i2s0_cdclk: i2s0-cdclk-pins {
 		samsung,pins = "gpd-1";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	i2s1_bus: i2s1-bus {
+	i2s1_bus: i2s1-bus-pins {
 		samsung,pins = "gpe-0", "gpe-2", "gpe-3", "gpe-4";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	i2s1_cdclk: i2s1-cdclk {
+	i2s1_cdclk: i2s1-cdclk-pins {
 		samsung,pins = "gpe-1";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	i2s2_bus: i2s2-bus {
+	i2s2_bus: i2s2-bus-pins {
 		/* S3C6410-only */
 		samsung,pins = "gpc-4", "gpc-5", "gpc-6", "gph-6",
 				"gph-8", "gph-9";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_5>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_5>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	i2s2_cdclk: i2s2-cdclk {
+	i2s2_cdclk: i2s2-cdclk-pins {
 		/* S3C6410-only */
 		samsung,pins = "gph-7";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_5>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_5>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	pcm0_bus: pcm0-bus {
+	pcm0_bus: pcm0-bus-pins {
 		samsung,pins = "gpd-0", "gpd-2", "gpd-3", "gpd-4";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	pcm0_extclk: pcm0-extclk {
+	pcm0_extclk: pcm0-extclk-pins {
 		samsung,pins = "gpd-1";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	pcm1_bus: pcm1-bus {
+	pcm1_bus: pcm1-bus-pins {
 		samsung,pins = "gpe-0", "gpe-2", "gpe-3", "gpe-4";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	pcm1_extclk: pcm1-extclk {
+	pcm1_extclk: pcm1-extclk-pins {
 		samsung,pins = "gpe-1";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	ac97_bus_0: ac97-bus-0 {
+	ac97_bus_0: ac97-bus-0-pins {
 		samsung,pins = "gpd-0", "gpd-1", "gpd-2", "gpd-3", "gpd-4";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_4>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	ac97_bus_1: ac97-bus-1 {
+	ac97_bus_1: ac97-bus-1-pins {
 		samsung,pins = "gpe-0", "gpe-1", "gpe-2", "gpe-3", "gpe-4";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_4>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	cam_port: cam-port {
+	cam_port: cam-port-pins {
 		samsung,pins = "gpf-0", "gpf-1", "gpf-2", "gpf-4",
 				"gpf-5", "gpf-6", "gpf-7", "gpf-8",
 				"gpf-9", "gpf-10", "gpf-11", "gpf-12";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	cam_rst: cam-rst {
+	cam_rst: cam-rst-pins {
 		samsung,pins = "gpf-3";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	cam_field: cam-field {
+	cam_field: cam-field-pins {
 		/* S3C6410-only */
 		samsung,pins = "gpb-4";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	pwm_extclk: pwm-extclk {
+	pwm_extclk: pwm-extclk-pins {
 		samsung,pins = "gpf-13";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	pwm0_out: pwm0-out {
+	pwm0_out: pwm0-out-pins {
 		samsung,pins = "gpf-14";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	pwm1_out: pwm1-out {
+	pwm1_out: pwm1-out-pins {
 		samsung,pins = "gpf-15";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	clkout0: clkout-0 {
+	clkout0: clkout-0-pins {
 		samsung,pins = "gpf-14";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_col0_0: keypad-col0-0 {
+	keypad_col0_0: keypad-col0-0-pins {
 		samsung,pins = "gph-0";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_4>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_col1_0: keypad-col1-0 {
+	keypad_col1_0: keypad-col1-0-pins {
 		samsung,pins = "gph-1";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_4>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_col2_0: keypad-col2-0 {
+	keypad_col2_0: keypad-col2-0-pins {
 		samsung,pins = "gph-2";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_4>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_col3_0: keypad-col3-0 {
+	keypad_col3_0: keypad-col3-0-pins {
 		samsung,pins = "gph-3";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_4>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_col4_0: keypad-col4-0 {
+	keypad_col4_0: keypad-col4-0-pins {
 		samsung,pins = "gph-4";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_4>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_col5_0: keypad-col5-0 {
+	keypad_col5_0: keypad-col5-0-pins {
 		samsung,pins = "gph-5";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_4>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_col6_0: keypad-col6-0 {
+	keypad_col6_0: keypad-col6-0-pins {
 		samsung,pins = "gph-6";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_4>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_col7_0: keypad-col7-0 {
+	keypad_col7_0: keypad-col7-0-pins {
 		samsung,pins = "gph-7";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_4>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_col0_1: keypad-col0-1 {
+	keypad_col0_1: keypad-col0-1-pins {
 		samsung,pins = "gpl-0";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_col1_1: keypad-col1-1 {
+	keypad_col1_1: keypad-col1-1-pins {
 		samsung,pins = "gpl-1";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_col2_1: keypad-col2-1 {
+	keypad_col2_1: keypad-col2-1-pins {
 		samsung,pins = "gpl-2";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_col3_1: keypad-col3-1 {
+	keypad_col3_1: keypad-col3-1-pins {
 		samsung,pins = "gpl-3";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_col4_1: keypad-col4-1 {
+	keypad_col4_1: keypad-col4-1-pins {
 		samsung,pins = "gpl-4";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_col5_1: keypad-col5-1 {
+	keypad_col5_1: keypad-col5-1-pins {
 		samsung,pins = "gpl-5";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_col6_1: keypad-col6-1 {
+	keypad_col6_1: keypad-col6-1-pins {
 		samsung,pins = "gpl-6";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_col7_1: keypad-col7-1 {
+	keypad_col7_1: keypad-col7-1-pins {
 		samsung,pins = "gpl-7";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_row0_0: keypad-row0-0 {
+	keypad_row0_0: keypad-row0-0-pins {
 		samsung,pins = "gpk-8";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_row1_0: keypad-row1-0 {
+	keypad_row1_0: keypad-row1-0-pins {
 		samsung,pins = "gpk-9";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_row2_0: keypad-row2-0 {
+	keypad_row2_0: keypad-row2-0-pins {
 		samsung,pins = "gpk-10";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_row3_0: keypad-row3-0 {
+	keypad_row3_0: keypad-row3-0-pins {
 		samsung,pins = "gpk-11";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_row4_0: keypad-row4-0 {
+	keypad_row4_0: keypad-row4-0-pins {
 		samsung,pins = "gpk-12";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_row5_0: keypad-row5-0 {
+	keypad_row5_0: keypad-row5-0-pins {
 		samsung,pins = "gpk-13";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_row6_0: keypad-row6-0 {
+	keypad_row6_0: keypad-row6-0-pins {
 		samsung,pins = "gpk-14";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_row7_0: keypad-row7-0 {
+	keypad_row7_0: keypad-row7-0-pins {
 		samsung,pins = "gpk-15";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_row0_1: keypad-row0-1 {
+	keypad_row0_1: keypad-row0-1-pins {
 		samsung,pins = "gpn-0";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_row1_1: keypad-row1-1 {
+	keypad_row1_1: keypad-row1-1-pins {
 		samsung,pins = "gpn-1";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_row2_1: keypad-row2-1 {
+	keypad_row2_1: keypad-row2-1-pins {
 		samsung,pins = "gpn-2";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_row3_1: keypad-row3-1 {
+	keypad_row3_1: keypad-row3-1-pins {
 		samsung,pins = "gpn-3";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_row4_1: keypad-row4-1 {
+	keypad_row4_1: keypad-row4-1-pins {
 		samsung,pins = "gpn-4";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_row5_1: keypad-row5-1 {
+	keypad_row5_1: keypad-row5-1-pins {
 		samsung,pins = "gpn-5";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_row6_1: keypad-row6-1 {
+	keypad_row6_1: keypad-row6-1-pins {
 		samsung,pins = "gpn-6";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	keypad_row7_1: keypad-row7-1 {
+	keypad_row7_1: keypad-row7-1-pins {
 		samsung,pins = "gpn-7";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	lcd_ctrl: lcd-ctrl {
+	lcd_ctrl: lcd-ctrl-pins {
 		samsung,pins = "gpj-8", "gpj-9", "gpj-10", "gpj-11";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	lcd_data16: lcd-data-width16 {
+	lcd_data16: lcd-data-width16-pins {
 		samsung,pins = "gpi-3", "gpi-4", "gpi-5", "gpi-6",
 				"gpi-7", "gpi-10", "gpi-11", "gpi-12",
 				"gpi-13", "gpi-14", "gpi-15", "gpj-3",
 				"gpj-4", "gpj-5", "gpj-6", "gpj-7";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	lcd_data18: lcd-data-width18 {
+	lcd_data18: lcd-data-width18-pins {
 		samsung,pins = "gpi-2", "gpi-3", "gpi-4", "gpi-5",
 				"gpi-6", "gpi-7", "gpi-10", "gpi-11",
 				"gpi-12", "gpi-13", "gpi-14", "gpi-15",
 				"gpj-2", "gpj-3", "gpj-4", "gpj-5",
 				"gpj-6", "gpj-7";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	lcd_data24: lcd-data-width24 {
+	lcd_data24: lcd-data-width24-pins {
 		samsung,pins = "gpi-0", "gpi-1", "gpi-2", "gpi-3",
 				"gpi-4", "gpi-5", "gpi-6", "gpi-7",
 				"gpi-8", "gpi-9", "gpi-10", "gpi-11",
 				"gpi-12", "gpi-13", "gpi-14", "gpi-15",
 				"gpj-0", "gpj-1", "gpj-2", "gpj-3",
 				"gpj-4", "gpj-5", "gpj-6", "gpj-7";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_2>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 
-	hsi_bus: hsi-bus {
+	hsi_bus: hsi-bus-pins {
 		samsung,pins = "gpk-0", "gpk-1", "gpk-2", "gpk-3",
 				"gpk-4", "gpk-5", "gpk-6", "gpk-7";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-function = <S3C64XX_PIN_FUNC_3>;
 		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
 	};
 };
diff --git a/arch/arm/boot/dts/s3c64xx-pinctrl.h b/arch/arm/boot/dts/s3c64xx-pinctrl.h
new file mode 100644
index 000000000000..645c591db357
--- /dev/null
+++ b/arch/arm/boot/dts/s3c64xx-pinctrl.h
@@ -0,0 +1,27 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Samsung S3C64xx DTS pinctrl constants
+ *
+ * Copyright (c) 2016 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
+ * Copyright (c) 2022 Linaro Ltd
+ * Author: Krzysztof Kozlowski <krzk@kernel.org>
+ */
+
+#ifndef __DTS_ARM_SAMSUNG_S3C64XX_PINCTRL_H__
+#define __DTS_ARM_SAMSUNG_S3C64XX_PINCTRL_H__
+
+#define S3C64XX_PIN_PULL_NONE		0
+#define S3C64XX_PIN_PULL_DOWN		1
+#define S3C64XX_PIN_PULL_UP		2
+
+#define S3C64XX_PIN_FUNC_INPUT		0
+#define S3C64XX_PIN_FUNC_OUTPUT		1
+#define S3C64XX_PIN_FUNC_2		2
+#define S3C64XX_PIN_FUNC_3		3
+#define S3C64XX_PIN_FUNC_4		4
+#define S3C64XX_PIN_FUNC_5		5
+#define S3C64XX_PIN_FUNC_6		6
+#define S3C64XX_PIN_FUNC_EINT		7
+
+#endif /* __DTS_ARM_SAMSUNG_S3C64XX_PINCTRL_H__ */
diff --git a/arch/arm/boot/dts/s3c64xx.dtsi b/arch/arm/boot/dts/s3c64xx.dtsi
index cb11a87dbc42..c03df6355500 100644
--- a/arch/arm/boot/dts/s3c64xx.dtsi
+++ b/arch/arm/boot/dts/s3c64xx.dtsi
@@ -59,7 +59,7 @@
 			#interrupt-cells = <1>;
 		};
 
-		sdhci0: sdhci@7c200000 {
+		sdhci0: mmc@7c200000 {
 			compatible = "samsung,s3c6410-sdhci";
 			reg = <0x7c200000 0x100>;
 			interrupt-parent = <&vic1>;
@@ -70,7 +70,7 @@
 			status = "disabled";
 		};
 
-		sdhci1: sdhci@7c300000 {
+		sdhci1: mmc@7c300000 {
 			compatible = "samsung,s3c6410-sdhci";
 			reg = <0x7c300000 0x100>;
 			interrupt-parent = <&vic1>;
@@ -81,7 +81,7 @@
 			status = "disabled";
 		};
 
-		sdhci2: sdhci@7c400000 {
+		sdhci2: mmc@7c400000 {
 			compatible = "samsung,s3c6410-sdhci";
 			reg = <0x7c400000 0x100>;
 			interrupt-parent = <&vic1>;
@@ -178,20 +178,12 @@
 			interrupt-parent = <&vic1>;
 			interrupts = <21>;
 
-			pctrl_int_map: pinctrl-interrupt-map {
-				interrupt-map = <0 &vic0 0>,
-						<1 &vic0 1>,
-						<2 &vic1 0>,
-						<3 &vic1 1>;
-				#address-cells = <0>;
-				#size-cells = <0>;
-				#interrupt-cells = <1>;
-			};
-
 			wakeup-interrupt-controller {
 				compatible = "samsung,s3c64xx-wakeup-eint";
-				interrupts = <0>, <1>, <2>, <3>;
-				interrupt-parent = <&pctrl_int_map>;
+				interrupts-extended = <&vic0 0>,
+						      <&vic0 1>,
+						      <&vic1 0>,
+						      <&vic1 1>;
 			};
 		};
 	};
diff --git a/arch/arm/boot/dts/s5pv210-aquila.dts b/arch/arm/boot/dts/s5pv210-aquila.dts
index 6423348034b6..0f5c6cd0f3a1 100644
--- a/arch/arm/boot/dts/s5pv210-aquila.dts
+++ b/arch/arm/boot/dts/s5pv210-aquila.dts
@@ -29,8 +29,7 @@
 
 	memory@30000000 {
 		device_type = "memory";
-		reg = <0x30000000 0x05000000
-			0x40000000 0x18000000>;
+		reg = <0x30000000 0x05000000>, <0x40000000 0x18000000>;
 	};
 
 	pmic_ap_clk: clock-0 {
@@ -391,9 +390,9 @@
 };
 
 &pinctrl0 {
-	t_flash_detect: t-flash-detect {
+	t_flash_detect: t-flash-detect-pins {
 		samsung,pins = "gph3-4";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_INPUT>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
 	};
 };
diff --git a/arch/arm/boot/dts/s5pv210-aries.dtsi b/arch/arm/boot/dts/s5pv210-aries.dtsi
index 160f8cd9a68d..964c5fe51755 100644
--- a/arch/arm/boot/dts/s5pv210-aries.dtsi
+++ b/arch/arm/boot/dts/s5pv210-aries.dtsi
@@ -24,9 +24,9 @@
 
 	memory@30000000 {
 		device_type = "memory";
-		reg = <0x30000000 0x05000000
-			0x40000000 0x10000000
-			0x50000000 0x08000000>;
+		reg = <0x30000000 0x05000000>,
+			<0x40000000 0x10000000>,
+			<0x50000000 0x08000000>;
 	};
 
 	reserved-memory {
@@ -564,7 +564,6 @@
 			reset-gpios = <&mp05 5 GPIO_ACTIVE_LOW>;
 			vdd3-supply = <&ldo7_reg>;
 			vci-supply = <&ldo17_reg>;
-			spi-cs-high;
 			spi-max-frequency = <1200000>;
 
 			pinctrl-names = "default";
@@ -636,7 +635,7 @@
 };
 
 &i2s0 {
-	dmas = <&pdma0 9>, <&pdma0 10>, <&pdma0 11>;
+	dmas = <&pdma0 10>, <&pdma0 9>, <&pdma0 11>;
 	status = "okay";
 };
 
@@ -645,185 +644,185 @@
 };
 
 &pinctrl0 {
-	bt_reset: bt-reset {
+	bt_reset: bt-reset-pins {
 		samsung,pins = "gpb-3";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
-	wlan_bt_en: wlan-bt-en {
+	wlan_bt_en: wlan-bt-en-pins {
 		samsung,pins = "gpb-5";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
 		samsung,pin-val = <1>;
 	};
 
-	codec_ldo: codec-ldo {
+	codec_ldo: codec-ldo-pins {
 		samsung,pins = "gpf3-4";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
 	};
 
 	prox_i2c_pins: gp2a-i2c-pins {
 		samsung,pins = "gpg0-2", "gpg2-2";
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
-	wlan_gpio_rst: wlan-gpio-rst {
+	wlan_gpio_rst: wlan-gpio-rst-pins {
 		samsung,pins = "gpg1-2";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
 	};
 
-	bt_wake: bt-wake {
+	bt_wake: bt-wake-pins {
 		samsung,pins = "gpg3-4";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
 	};
 
-	gp2a_irq: gp2a-irq {
+	gp2a_irq: gp2a-irq-pins {
 		samsung,pins = "gph0-2";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_DOWN>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_F>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_DOWN>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
 	pmic_dvs_pins: pmic-dvs-pins {
 		samsung,pins = "gph0-3", "gph0-4", "gph0-5";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 		samsung,pin-val = <0>;
 	};
 
-	pmic_irq: pmic-irq {
+	pmic_irq: pmic-irq-pins {
 		samsung,pins = "gph0-7";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_F>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
-	wifi_host_wake: wifi-host-wake {
+	wifi_host_wake: wifi-host-wake-pins {
 		samsung,pins = "gph2-4";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_DOWN>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_INPUT>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_DOWN>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
-	bt_host_wake: bt-host-wake {
+	bt_host_wake: bt-host-wake-pins {
 		samsung,pins = "gph2-5";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_DOWN>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_INPUT>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_DOWN>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
-	musb_irq: musq-irq {
+	musb_irq: musq-irq-pins {
 		samsung,pins = "gph2-7";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_INPUT>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
-	tf_detect: tf-detect {
+	tf_detect: tf-detect-pins {
 		samsung,pins = "gph3-4";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_DOWN>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_INPUT>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_DOWN>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
-	wifi_wake: wifi-wake {
+	wifi_wake: wifi-wake-pins {
 		samsung,pins = "gph3-5";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
 	};
 
 	magnetometer_i2c_pins: yas529-i2c-pins {
 		samsung,pins = "gpj0-0", "gpj0-1";
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
-	ts_irq: ts-irq {
+	ts_irq: ts-irq-pins {
 		samsung,pins = "gpj0-5";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_INPUT>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
-	vibrator_ena: vibrator-ena {
+	vibrator_ena: vibrator-ena-pins {
 		samsung,pins = "gpj1-1";
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
-	gp2a_power: gp2a-power {
+	gp2a_power: gp2a-power-pins {
 		samsung,pins = "gpj1-4";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
 	touchkey_i2c_pins: touchkey-i2c-pins {
 		samsung,pins = "gpj3-0", "gpj3-1";
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
-	touchkey_vdd_ena: touchkey-vdd-ena {
+	touchkey_vdd_ena: touchkey-vdd-ena-pins {
 		samsung,pins = "gpj3-2";
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
 	musb_i2c_pins: musb-i2c-pins {
 		samsung,pins = "gpj3-4", "gpj3-5";
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
 	accel_i2c_pins: accel-i2c-pins {
 		samsung,pins = "gpj3-6", "gpj3-7";
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
 	pmic_i2c_pins: pmic-i2c-pins {
 		samsung,pins = "gpj4-0", "gpj4-3";
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
-	touchkey_irq: touchkey-irq {
+	touchkey_irq: touchkey-irq-pins {
 		samsung,pins = "gpj4-1";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_UP>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_INPUT>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_UP>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
 	lcd_spi_pins: spi-lcd-pins {
 		samsung,pins = "mp01-1", "mp04-1", "mp04-3";
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
 	fg_i2c_pins: fg-i2c-pins {
 		samsung,pins = "mp05-0", "mp05-1";
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
 	sound_i2c_pins: sound-i2c-pins {
 		samsung,pins = "mp05-2", "mp05-3";
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
-	panel_rst: panel-rst {
+	panel_rst: panel-rst-pins {
 		samsung,pins = "mp05-5";
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 };
 
@@ -895,7 +894,7 @@
 		device-wakeup-gpios = <&gpg3 4 GPIO_ACTIVE_HIGH>;
 		interrupt-parent = <&gph2>;
 		interrupts = <5 IRQ_TYPE_LEVEL_HIGH>;
-		interrupt-names = "host-wake";
+		interrupt-names = "host-wakeup";
 	};
 };
 
diff --git a/arch/arm/boot/dts/s5pv210-fascinate4g.dts b/arch/arm/boot/dts/s5pv210-fascinate4g.dts
index 7427c84f1126..eaa7c4f0e257 100644
--- a/arch/arm/boot/dts/s5pv210-fascinate4g.dts
+++ b/arch/arm/boot/dts/s5pv210-fascinate4g.dts
@@ -17,20 +17,20 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		power {
+		key-power {
 			label = "power";
 			gpios = <&gph2 6 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
 			wakeup-source;
 		};
 
-		vol-down {
+		key-vol-down {
 			label = "volume_down";
 			gpios = <&gph3 2 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_VOLUMEDOWN>;
 		};
 
-		vol-up {
+		key-vol-up {
 			label = "volume_up";
 			gpios = <&gph3 1 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_VOLUMEUP>;
@@ -126,39 +126,39 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&sleep_cfg>;
 
-	headset_det: headset-det {
+	headset_det: headset-det-pins {
 		samsung,pins = "gph0-6", "gph3-6";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_F>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
 	};
 
-	fg_irq: fg-irq {
+	fg_irq: fg-irq-pins {
 		samsung,pins = "gph3-3";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_F>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
-	headset_micbias_ena: headset-micbias-ena {
+	headset_micbias_ena: headset-micbias-ena-pins {
 		samsung,pins = "gpj2-5";
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
-	earpath_sel: earpath-sel {
+	earpath_sel: earpath-sel-pins {
 		samsung,pins = "gpj2-6";
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
-	main_micbias_ena: main-micbias-ena {
+	main_micbias_ena: main-micbias-ena-pins {
 		samsung,pins = "gpj4-2";
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
 	/* Based on vendor kernel v2.6.35.7 */
-	sleep_cfg: sleep-cfg {
+	sleep_cfg: sleep-state {
 		PIN_SLP(gpa0-0, PREV, NONE);
 		PIN_SLP(gpa0-1, PREV, NONE);
 		PIN_SLP(gpa0-2, PREV, NONE);
diff --git a/arch/arm/boot/dts/s5pv210-galaxys.dts b/arch/arm/boot/dts/s5pv210-galaxys.dts
index eeec2bdece11..532d3f5bceb1 100644
--- a/arch/arm/boot/dts/s5pv210-galaxys.dts
+++ b/arch/arm/boot/dts/s5pv210-galaxys.dts
@@ -24,26 +24,26 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		power {
+		key-power {
 			label = "power";
 			gpios = <&gph2 6 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
 			wakeup-source;
 		};
 
-		vol-down {
+		key-vol-down {
 			label = "volume_down";
 			gpios = <&gph3 1 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_VOLUMEDOWN>;
 		};
 
-		vol-up {
+		key-vol-up {
 			label = "volume_up";
 			gpios = <&gph3 2 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_VOLUMEUP>;
 		};
 
-		home {
+		key-home {
 			label = "home";
 			gpios = <&gph3 5 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_HOME>;
@@ -152,51 +152,51 @@
 
 	fm_i2c_pins: fm-i2c-pins {
 		samsung,pins = "gpd1-2", "gpd1-3";
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
-	headset_det: headset-det {
+	headset_det: headset-det-pins {
 		samsung,pins = "gph0-6", "gph3-6";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_F>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
 	};
 
-	fm_irq: fm-irq {
+	fm_irq: fm-irq-pins {
 		samsung,pins = "gpj2-4";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_UP>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_INPUT>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_UP>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
-	fm_rst: fm-rst {
+	fm_rst: fm-rst-pins {
 		samsung,pins = "gpj2-5";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
-	earpath_sel: earpath-sel {
+	earpath_sel: earpath-sel-pins {
 		samsung,pins = "gpj2-6";
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
-	massmemory_en: massmemory-en {
+	massmemory_en: massmemory-en-pins {
 		samsung,pins = "gpj2-7";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
-	micbias_reg_ena: micbias-reg-ena {
+	micbias_reg_ena: micbias-reg-ena-pins {
 		samsung,pins = "gpj4-2";
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
 	/* Based on CyanogenMod 3.0.101 kernel */
-	sleep_cfg: sleep-cfg {
+	sleep_cfg: sleep-state {
 		PIN_SLP(gpa0-0, PREV, NONE);
 		PIN_SLP(gpa0-1, PREV, NONE);
 		PIN_SLP(gpa0-2, PREV, NONE);
diff --git a/arch/arm/boot/dts/s5pv210-goni.dts b/arch/arm/boot/dts/s5pv210-goni.dts
index c6f39147cb96..d32f42dd1bf5 100644
--- a/arch/arm/boot/dts/s5pv210-goni.dts
+++ b/arch/arm/boot/dts/s5pv210-goni.dts
@@ -30,9 +30,9 @@
 
 	memory@30000000 {
 		device_type = "memory";
-		reg = <0x30000000 0x05000000
-			0x40000000 0x10000000
-			0x50000000 0x08000000>;
+		reg = <0x30000000 0x05000000>,
+			<0x40000000 0x10000000>,
+			<0x50000000 0x08000000>;
 	};
 
 	pmic_ap_clk: clock-0 {
diff --git a/arch/arm/boot/dts/s5pv210-pinctrl.dtsi b/arch/arm/boot/dts/s5pv210-pinctrl.dtsi
index b8c5172c31dd..6d6daef9fb7a 100644
--- a/arch/arm/boot/dts/s5pv210-pinctrl.dtsi
+++ b/arch/arm/boot/dts/s5pv210-pinctrl.dtsi
@@ -16,17 +16,17 @@
  * nodes can be added to this file.
  */
 
-#include <dt-bindings/pinctrl/samsung.h>
+#include "s5pv210-pinctrl.h"
 
 #define PIN_SLP(_pin, _mode, _pull)					\
 	_pin {								\
 		samsung,pins = #_pin;					\
-		samsung,pin-con-pdn = <EXYNOS_PIN_PDN_ ##_mode>;	\
-		samsung,pin-pud-pdn = <S3C64XX_PIN_PULL_ ##_pull>;	\
+		samsung,pin-con-pdn = <S5PV210_PIN_PDN_ ##_mode>;	\
+		samsung,pin-pud-pdn = <S5PV210_PIN_PULL_ ##_pull>;	\
 	}
 
 &pinctrl0 {
-	gpa0: gpa0 {
+	gpa0: gpa0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -34,7 +34,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpa1: gpa1 {
+	gpa1: gpa1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -42,7 +42,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpb: gpb {
+	gpb: gpb-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -50,7 +50,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpc0: gpc0 {
+	gpc0: gpc0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -58,7 +58,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpc1: gpc1 {
+	gpc1: gpc1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -66,7 +66,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpd0: gpd0 {
+	gpd0: gpd0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -74,7 +74,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpd1: gpd1 {
+	gpd1: gpd1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -82,7 +82,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpe0: gpe0 {
+	gpe0: gpe0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -90,7 +90,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpe1: gpe1 {
+	gpe1: gpe1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -98,7 +98,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpf0: gpf0 {
+	gpf0: gpf0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -106,7 +106,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpf1: gpf1 {
+	gpf1: gpf1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -114,7 +114,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpf2: gpf2 {
+	gpf2: gpf2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -122,7 +122,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpf3: gpf3 {
+	gpf3: gpf3-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -130,7 +130,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpg0: gpg0 {
+	gpg0: gpg0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -138,7 +138,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpg1: gpg1 {
+	gpg1: gpg1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -146,7 +146,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpg2: gpg2 {
+	gpg2: gpg2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -154,7 +154,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpg3: gpg3 {
+	gpg3: gpg3-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -162,7 +162,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpj0: gpj0 {
+	gpj0: gpj0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -170,7 +170,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpj1: gpj1 {
+	gpj1: gpj1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -178,7 +178,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpj2: gpj2 {
+	gpj2: gpj2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -186,7 +186,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpj3: gpj3 {
+	gpj3: gpj3-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -194,7 +194,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpj4: gpj4 {
+	gpj4: gpj4-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -202,47 +202,47 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpi: gpi {
+	gpi: gpi-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	mp01: mp01 {
+	mp01: mp01-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	mp02: mp02 {
+	mp02: mp02-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	mp03: mp03 {
+	mp03: mp03-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	mp04: mp04 {
+	mp04: mp04-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	mp05: mp05 {
+	mp05: mp05-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	mp06: mp06 {
+	mp06: mp06-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	mp07: mp07 {
+	mp07: mp07-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 	};
 
-	gph0: gph0 {
+	gph0: gph0-gpio-bank {
 		gpio-controller;
 		interrupt-controller;
 		interrupt-parent = <&vic0>;
@@ -252,7 +252,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gph1: gph1 {
+	gph1: gph1-gpio-bank {
 		gpio-controller;
 		interrupt-controller;
 		interrupt-parent = <&vic0>;
@@ -262,7 +262,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gph2: gph2 {
+	gph2: gph2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -270,7 +270,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gph3: gph3 {
+	gph3: gph3-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -278,572 +278,572 @@
 		#interrupt-cells = <2>;
 	};
 
-	uart0_data: uart0-data {
+	uart0_data: uart0-data-pins {
 		samsung,pins = "gpa0-0", "gpa0-1";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
-	uart0_fctl: uart0-fctl {
+	uart0_fctl: uart0-fctl-pins {
 		samsung,pins = "gpa0-2", "gpa0-3";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
-	uart1_data: uart1-data {
+	uart1_data: uart1-data-pins {
 		samsung,pins = "gpa0-4", "gpa0-5";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
-	uart1_fctl: uart1-fctl {
+	uart1_fctl: uart1-fctl-pins {
 		samsung,pins = "gpa0-6", "gpa0-7";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
-	uart2_data: uart2-data {
+	uart2_data: uart2-data-pins {
 		samsung,pins = "gpa1-0", "gpa1-1";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
-	uart2_fctl: uart2-fctl {
+	uart2_fctl: uart2-fctl-pins {
 		samsung,pins = "gpa1-2", "gpa1-3";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_3>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
-	uart3_data: uart3-data {
+	uart3_data: uart3-data-pins {
 		samsung,pins = "gpa1-2", "gpa1-3";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
-	uart_audio: uart-audio {
+	uart_audio: uart-audio-pins {
 		samsung,pins = "gpa1-2", "gpa1-3";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_4>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
-	spi0_bus: spi0-bus {
+	spi0_bus: spi0-bus-pins {
 		samsung,pins = "gpb-0", "gpb-2", "gpb-3";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_UP>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_UP>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
-	spi1_bus: spi1-bus {
+	spi1_bus: spi1-bus-pins {
 		samsung,pins = "gpb-4", "gpb-6", "gpb-7";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_UP>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_UP>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
-	i2s0_bus: i2s0-bus {
+	i2s0_bus: i2s0-bus-pins {
 		samsung,pins = "gpi-0", "gpi-1", "gpi-2", "gpi-3",
 				"gpi-4", "gpi-5", "gpi-6";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
-	i2s1_bus: i2s1-bus {
+	i2s1_bus: i2s1-bus-pins {
 		samsung,pins = "gpc0-0", "gpc0-1", "gpc0-2", "gpc0-3",
 				"gpc0-4";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
-	i2s2_bus: i2s2-bus {
+	i2s2_bus: i2s2-bus-pins {
 		samsung,pins = "gpc1-0", "gpc1-1", "gpc1-2", "gpc1-3",
 				"gpc1-4";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_4>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
-	pcm1_bus: pcm1-bus {
+	pcm1_bus: pcm1-bus-pins {
 		samsung,pins = "gpc0-0", "gpc0-1", "gpc0-2", "gpc0-3",
 				"gpc0-4";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_3>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
-	ac97_bus: ac97-bus {
+	ac97_bus: ac97-bus-pins {
 		samsung,pins = "gpc0-0", "gpc0-1", "gpc0-2", "gpc0-3",
 				"gpc0-4";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_4>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
-	i2s2_bus: i2s2-bus {
+	i2s2_bus: i2s2-bus-pins {
 		samsung,pins = "gpc1-0", "gpc1-1", "gpc1-2", "gpc1-3",
 				"gpc1-4";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
-	pcm2_bus: pcm2-bus {
+	pcm2_bus: pcm2-bus-pins {
 		samsung,pins = "gpc1-0", "gpc1-1", "gpc1-2", "gpc1-3",
 				"gpc1-4";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_3>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
-	spdif_bus: spdif-bus {
+	spdif_bus: spdif-bus-pins {
 		samsung,pins = "gpc1-0", "gpc1-1";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_4>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
-	spi2_bus: spi2-bus {
+	spi2_bus: spi2-bus-pins {
 		samsung,pins = "gpc1-1", "gpc1-2", "gpc1-3", "gpc1-4";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_5>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_UP>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_5>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_UP>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
-	i2c0_bus: i2c0-bus {
+	i2c0_bus: i2c0-bus-pins {
 		samsung,pins = "gpd1-0", "gpd1-1";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_UP>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_UP>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
-	i2c1_bus: i2c1-bus {
+	i2c1_bus: i2c1-bus-pins {
 		samsung,pins = "gpd1-2", "gpd1-3";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_UP>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_UP>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
-	i2c2_bus: i2c2-bus {
+	i2c2_bus: i2c2-bus-pins {
 		samsung,pins = "gpd1-4", "gpd1-5";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_UP>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_UP>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
-	pwm0_out: pwm0-out {
+	pwm0_out: pwm0-out-pins {
 		samsung,pins = "gpd0-0";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
-	pwm1_out: pwm1-out {
+	pwm1_out: pwm1-out-pins {
 		samsung,pins = "gpd0-1";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
-	pwm2_out: pwm2-out {
+	pwm2_out: pwm2-out-pins {
 		samsung,pins = "gpd0-2";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
-	pwm3_out: pwm3-out {
+	pwm3_out: pwm3-out-pins {
 		samsung,pins = "gpd0-3";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
-	keypad_row0: keypad-row-0 {
+	keypad_row0: keypad-row-0-pins {
 		samsung,pins = "gph3-0";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_3>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
-	keypad_row1: keypad-row-1 {
+	keypad_row1: keypad-row-1-pins {
 		samsung,pins = "gph3-1";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_3>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
-	keypad_row2: keypad-row-2 {
+	keypad_row2: keypad-row-2-pins {
 		samsung,pins = "gph3-2";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_3>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
-	keypad_row3: keypad-row-3 {
+	keypad_row3: keypad-row-3-pins {
 		samsung,pins = "gph3-3";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_3>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
-	keypad_row4: keypad-row-4 {
+	keypad_row4: keypad-row-4-pins {
 		samsung,pins = "gph3-4";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_3>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
-	keypad_row5: keypad-row-5 {
+	keypad_row5: keypad-row-5-pins {
 		samsung,pins = "gph3-5";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_3>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
-	keypad_row6: keypad-row-6 {
+	keypad_row6: keypad-row-6-pins {
 		samsung,pins = "gph3-6";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_3>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
-	keypad_row7: keypad-row-7 {
+	keypad_row7: keypad-row-7-pins {
 		samsung,pins = "gph3-7";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_3>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
-	keypad_col0: keypad-col-0 {
+	keypad_col0: keypad-col-0-pins {
 		samsung,pins = "gph2-0";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_3>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
-	keypad_col1: keypad-col-1 {
+	keypad_col1: keypad-col-1-pins {
 		samsung,pins = "gph2-1";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_3>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
-	keypad_col2: keypad-col-2 {
+	keypad_col2: keypad-col-2-pins {
 		samsung,pins = "gph2-2";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_3>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
-	keypad_col3: keypad-col-3 {
+	keypad_col3: keypad-col-3-pins {
 		samsung,pins = "gph2-3";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_3>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
-	keypad_col4: keypad-col-4 {
+	keypad_col4: keypad-col-4-pins {
 		samsung,pins = "gph2-4";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_3>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
-	keypad_col5: keypad-col-5 {
+	keypad_col5: keypad-col-5-pins {
 		samsung,pins = "gph2-5";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_3>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
-	keypad_col6: keypad-col-6 {
+	keypad_col6: keypad-col-6-pins {
 		samsung,pins = "gph2-6";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_3>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
-	keypad_col7: keypad-col-7 {
+	keypad_col7: keypad-col-7-pins {
 		samsung,pins = "gph2-7";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_3>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
-	sd0_clk: sd0-clk {
+	sd0_clk: sd0-clk-pins {
 		samsung,pins = "gpg0-0";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV4>;
 	};
 
-	sd0_cmd: sd0-cmd {
+	sd0_cmd: sd0-cmd-pins {
 		samsung,pins = "gpg0-1";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV4>;
 	};
 
-	sd0_cd: sd0-cd {
+	sd0_cd: sd0-cd-pins {
 		samsung,pins = "gpg0-2";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_UP>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_UP>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV4>;
 	};
 
-	sd0_bus1: sd0-bus-width1 {
+	sd0_bus1: sd0-bus-width1-pins {
 		samsung,pins = "gpg0-3";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_UP>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_UP>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV4>;
 	};
 
-	sd0_bus4: sd0-bus-width4 {
+	sd0_bus4: sd0-bus-width4-pins {
 		samsung,pins = "gpg0-3", "gpg0-4", "gpg0-5", "gpg0-6";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_UP>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_UP>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV4>;
 	};
 
-	sd0_bus8: sd0-bus-width8 {
+	sd0_bus8: sd0-bus-width8-pins {
 		samsung,pins = "gpg1-3", "gpg1-4", "gpg1-5", "gpg1-6";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_UP>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_3>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_UP>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV4>;
 	};
 
-	sd1_clk: sd1-clk {
+	sd1_clk: sd1-clk-pins {
 		samsung,pins = "gpg1-0";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV4>;
 	};
 
-	sd1_cmd: sd1-cmd {
+	sd1_cmd: sd1-cmd-pins {
 		samsung,pins = "gpg1-1";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV4>;
 	};
 
-	sd1_cd: sd1-cd {
+	sd1_cd: sd1-cd-pins {
 		samsung,pins = "gpg1-2";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_UP>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_UP>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV4>;
 	};
 
-	sd1_bus1: sd1-bus-width1 {
+	sd1_bus1: sd1-bus-width1-pins {
 		samsung,pins = "gpg1-3";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_UP>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_UP>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV4>;
 	};
 
-	sd1_bus4: sd1-bus-width4 {
+	sd1_bus4: sd1-bus-width4-pins {
 		samsung,pins = "gpg1-3", "gpg1-4", "gpg1-5", "gpg1-6";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_UP>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_UP>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV4>;
 	};
 
-	sd2_clk: sd2-clk {
+	sd2_clk: sd2-clk-pins {
 		samsung,pins = "gpg2-0";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV4>;
 	};
 
-	sd2_cmd: sd2-cmd {
+	sd2_cmd: sd2-cmd-pins {
 		samsung,pins = "gpg2-1";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV4>;
 	};
 
-	sd2_cd: sd2-cd {
+	sd2_cd: sd2-cd-pins {
 		samsung,pins = "gpg2-2";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_UP>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_UP>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV4>;
 	};
 
-	sd2_bus1: sd2-bus-width1 {
+	sd2_bus1: sd2-bus-width1-pins {
 		samsung,pins = "gpg2-3";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_UP>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_UP>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV4>;
 	};
 
-	sd2_bus4: sd2-bus-width4 {
+	sd2_bus4: sd2-bus-width4-pins {
 		samsung,pins = "gpg2-3", "gpg2-4", "gpg2-5", "gpg2-6";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_UP>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_UP>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV4>;
 	};
 
-	sd2_bus8: sd2-bus-width8 {
+	sd2_bus8: sd2-bus-width8-pins {
 		samsung,pins = "gpg3-3", "gpg3-4", "gpg3-5", "gpg3-6";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_UP>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_3>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_UP>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV4>;
 	};
 
-	sd3_clk: sd3-clk {
+	sd3_clk: sd3-clk-pins {
 		samsung,pins = "gpg3-0";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV4>;
 	};
 
-	sd3_cmd: sd3-cmd {
+	sd3_cmd: sd3-cmd-pins {
 		samsung,pins = "gpg3-1";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV4>;
 	};
 
-	sd3_cd: sd3-cd {
+	sd3_cd: sd3-cd-pins {
 		samsung,pins = "gpg3-2";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_UP>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_UP>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV4>;
 	};
 
-	sd3_bus1: sd3-bus-width1 {
+	sd3_bus1: sd3-bus-width1-pins {
 		samsung,pins = "gpg3-3";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_UP>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_UP>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV4>;
 	};
 
-	sd3_bus4: sd3-bus-width4 {
+	sd3_bus4: sd3-bus-width4-pins {
 		samsung,pins = "gpg3-3", "gpg3-4", "gpg3-5", "gpg3-6";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_UP>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_UP>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV4>;
 	};
 
-	eint0: ext-int0 {
+	eint0: ext-int0-pins {
 		samsung,pins = "gph0-0";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_F>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
-	eint8: ext-int8 {
+	eint8: ext-int8-pins {
 		samsung,pins = "gph1-0";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_F>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
-	eint15: ext-int15 {
+	eint15: ext-int15-pins {
 		samsung,pins = "gph1-7";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_F>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
-	eint16: ext-int16 {
+	eint16: ext-int16-pins {
 		samsung,pins = "gph2-0";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_F>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
-	eint31: ext-int31 {
+	eint31: ext-int31-pins {
 		samsung,pins = "gph3-7";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_F>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
-	cam_port_a_io: cam-port-a-io {
+	cam_port_a_io: cam-port-a-io-pins {
 		samsung,pins = "gpe0-0", "gpe0-1", "gpe0-2", "gpe0-3",
 				"gpe0-4", "gpe0-5", "gpe0-6", "gpe0-7",
 				"gpe1-0", "gpe1-1", "gpe1-2", "gpe1-4";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
-	cam_port_a_clk_active: cam-port-a-clk-active {
+	cam_port_a_clk_active: cam-port-a-clk-active-pins {
 		samsung,pins = "gpe1-3";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV4>;
 	};
 
-	cam_port_a_clk_idle: cam-port-a-clk-idle {
+	cam_port_a_clk_idle: cam-port-a-clk-idle-pins {
 		samsung,pins = "gpe1-3";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_DOWN>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_INPUT>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_DOWN>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
-	cam_port_b_io: cam-port-b-io {
+	cam_port_b_io: cam-port-b-io-pins {
 		samsung,pins = "gpj0-0", "gpj0-1", "gpj0-2", "gpj0-3",
 				"gpj0-4", "gpj0-5", "gpj0-6", "gpj0-7",
 				"gpj1-0", "gpj1-1", "gpj1-2", "gpj1-4";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_3>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
-	cam_port_b_clk_active: cam-port-b-clk-active {
+	cam_port_b_clk_active: cam-port-b-clk-active-pins {
 		samsung,pins = "gpj1-3";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_3>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV4>;
 	};
 
-	cam_port_b_clk_idle: cam-port-b-clk-idle {
+	cam_port_b_clk_idle: cam-port-b-clk-idle-pins {
 		samsung,pins = "gpj1-3";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_DOWN>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_INPUT>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_DOWN>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
-		lcd_ctrl: lcd-ctrl {
+	lcd_ctrl: lcd-ctrl-pins {
 		samsung,pins = "gpd0-0", "gpd0-1";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_3>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
-	lcd_sync: lcd-sync {
+	lcd_sync: lcd-sync-pins {
 		samsung,pins = "gpf0-0", "gpf0-1";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
-	lcd_clk: lcd-clk {
+	lcd_clk: lcd-clk-pins {
 		samsung,pins = "gpf0-0", "gpf0-1", "gpf0-2", "gpf0-3";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 
-	lcd_data24: lcd-data-width24 {
+	lcd_data24: lcd-data-width24-pins {
 		samsung,pins =  "gpf0-4", "gpf0-5", "gpf0-6", "gpf0-7",
 				"gpf1-0", "gpf1-1", "gpf1-2", "gpf1-3",
 				"gpf1-4", "gpf1-5", "gpf1-6", "gpf1-7",
 				"gpf2-0", "gpf2-1", "gpf2-2", "gpf2-3",
 				"gpf2-4", "gpf2-5", "gpf2-6", "gpf2-7",
 				"gpf3-0", "gpf3-1", "gpf3-2", "gpf3-3";
-		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
-		samsung,pin-pud = <S3C64XX_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-function = <S5PV210_PIN_FUNC_2>;
+		samsung,pin-pud = <S5PV210_PIN_PULL_NONE>;
+		samsung,pin-drv = <S5PV210_PIN_DRV_LV1>;
 	};
 };
diff --git a/arch/arm/boot/dts/s5pv210-pinctrl.h b/arch/arm/boot/dts/s5pv210-pinctrl.h
new file mode 100644
index 000000000000..29bdf376d8f1
--- /dev/null
+++ b/arch/arm/boot/dts/s5pv210-pinctrl.h
@@ -0,0 +1,39 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Samsung S5PV210 DTS pinctrl constants
+ *
+ * Copyright (c) 2016 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
+ * Copyright (c) 2022 Linaro Ltd
+ * Author: Krzysztof Kozlowski <krzk@kernel.org>
+ */
+
+#ifndef __DTS_ARM_SAMSUNG_S5PV210_PINCTRL_H__
+#define __DTS_ARM_SAMSUNG_S5PV210_PINCTRL_H__
+
+#define S5PV210_PIN_PULL_NONE		0
+#define S5PV210_PIN_PULL_DOWN		1
+#define S5PV210_PIN_PULL_UP		2
+
+/* Pin function in power down mode */
+#define S5PV210_PIN_PDN_OUT0		0
+#define S5PV210_PIN_PDN_OUT1		1
+#define S5PV210_PIN_PDN_INPUT		2
+#define S5PV210_PIN_PDN_PREV		3
+
+#define S5PV210_PIN_DRV_LV1		0
+#define S5PV210_PIN_DRV_LV2		2
+#define S5PV210_PIN_DRV_LV3		1
+#define S5PV210_PIN_DRV_LV4		3
+
+#define S5PV210_PIN_FUNC_INPUT		0
+#define S5PV210_PIN_FUNC_OUTPUT		1
+#define S5PV210_PIN_FUNC_2		2
+#define S5PV210_PIN_FUNC_3		3
+#define S5PV210_PIN_FUNC_4		4
+#define S5PV210_PIN_FUNC_5		5
+#define S5PV210_PIN_FUNC_6		6
+#define S5PV210_PIN_FUNC_EINT		0xf
+#define S5PV210_PIN_FUNC_F		S5PV210_PIN_FUNC_EINT
+
+#endif /* __DTS_ARM_SAMSUNG_S5PV210_PINCTRL_H__ */
diff --git a/arch/arm/boot/dts/s5pv210.dtsi b/arch/arm/boot/dts/s5pv210.dtsi
index 353ba7b09a0c..12e90a1cc6a1 100644
--- a/arch/arm/boot/dts/s5pv210.dtsi
+++ b/arch/arm/boot/dts/s5pv210.dtsi
@@ -117,7 +117,7 @@
 			};
 		};
 
-		pdma0: dma@e0900000 {
+		pdma0: dma-controller@e0900000 {
 			compatible = "arm,pl330", "arm,primecell";
 			reg = <0xe0900000 0x1000>;
 			interrupt-parent = <&vic0>;
@@ -125,11 +125,9 @@
 			clocks = <&clocks CLK_PDMA0>;
 			clock-names = "apb_pclk";
 			#dma-cells = <1>;
-			#dma-channels = <8>;
-			#dma-requests = <32>;
 		};
 
-		pdma1: dma@e0a00000 {
+		pdma1: dma-controller@e0a00000 {
 			compatible = "arm,pl330", "arm,primecell";
 			reg = <0xe0a00000 0x1000>;
 			interrupt-parent = <&vic0>;
@@ -137,8 +135,6 @@
 			clocks = <&clocks CLK_PDMA1>;
 			clock-names = "apb_pclk";
 			#dma-cells = <1>;
-			#dma-channels = <8>;
-			#dma-requests = <32>;
 		};
 
 		adc: adc@e1700000 {
@@ -239,8 +235,8 @@
 			reg = <0xeee30000 0x1000>;
 			interrupt-parent = <&vic2>;
 			interrupts = <16>;
-			dma-names = "rx", "tx", "tx-sec";
-			dmas = <&pdma1 9>, <&pdma1 10>, <&pdma1 11>;
+			dma-names = "tx", "rx", "tx-sec";
+			dmas = <&pdma1 10>, <&pdma1 9>, <&pdma1 11>;
 			clock-names = "iis",
 				      "i2s_opclk0",
 				      "i2s_opclk1";
@@ -259,8 +255,8 @@
 			reg = <0xe2100000 0x1000>;
 			interrupt-parent = <&vic2>;
 			interrupts = <17>;
-			dma-names = "rx", "tx";
-			dmas = <&pdma1 12>, <&pdma1 13>;
+			dma-names = "tx", "rx";
+			dmas = <&pdma1 13>, <&pdma1 12>;
 			clock-names = "iis", "i2s_opclk0";
 			clocks = <&clocks CLK_I2S1>, <&clocks SCLK_AUDIO1>;
 			pinctrl-names = "default";
@@ -274,8 +270,8 @@
 			reg = <0xe2a00000 0x1000>;
 			interrupt-parent = <&vic2>;
 			interrupts = <18>;
-			dma-names = "rx", "tx";
-			dmas = <&pdma1 14>, <&pdma1 15>;
+			dma-names = "tx", "rx";
+			dmas = <&pdma1 15>, <&pdma1 14>;
 			clock-names = "iis", "i2s_opclk0";
 			clocks = <&clocks CLK_I2S2>, <&clocks SCLK_AUDIO2>;
 			pinctrl-names = "default";
@@ -361,7 +357,7 @@
 			status = "disabled";
 		};
 
-		sdhci0: sdhci@eb000000 {
+		sdhci0: mmc@eb000000 {
 			compatible = "samsung,s3c6410-sdhci";
 			reg = <0xeb000000 0x100000>;
 			interrupt-parent = <&vic1>;
@@ -372,7 +368,7 @@
 			status = "disabled";
 		};
 
-		sdhci1: sdhci@eb100000 {
+		sdhci1: mmc@eb100000 {
 			compatible = "samsung,s3c6410-sdhci";
 			reg = <0xeb100000 0x100000>;
 			interrupt-parent = <&vic1>;
@@ -383,7 +379,7 @@
 			status = "disabled";
 		};
 
-		sdhci2: sdhci@eb200000 {
+		sdhci2: mmc@eb200000 {
 			compatible = "samsung,s3c6410-sdhci";
 			reg = <0xeb200000 0x100000>;
 			interrupt-parent = <&vic1>;
@@ -394,7 +390,7 @@
 			status = "disabled";
 		};
 
-		sdhci3: sdhci@eb300000 {
+		sdhci3: mmc@eb300000 {
 			compatible = "samsung,s3c6410-sdhci";
 			reg = <0xeb300000 0x100000>;
 			interrupt-parent = <&vic3>;
@@ -427,38 +423,28 @@
 			status = "disabled";
 		};
 
-		ehci: ehci@ec200000 {
+		ehci: usb@ec200000 {
 			compatible = "samsung,exynos4210-ehci";
 			reg = <0xec200000 0x100>;
 			interrupts = <23>;
 			interrupt-parent = <&vic1>;
 			clocks = <&clocks CLK_USB_HOST>;
 			clock-names = "usbhost";
-			#address-cells = <1>;
-			#size-cells = <0>;
+			phys = <&usbphy 1>;
+			phy-names = "host";
 			status = "disabled";
-
-			port@0 {
-				reg = <0>;
-				phys = <&usbphy 1>;
-			};
 		};
 
-		ohci: ohci@ec300000 {
+		ohci: usb@ec300000 {
 			compatible = "samsung,exynos4210-ohci";
 			reg = <0xec300000 0x100>;
 			interrupts = <23>;
 			interrupt-parent = <&vic1>;
 			clocks = <&clocks CLK_USB_HOST>;
 			clock-names = "usbhost";
-			#address-cells = <1>;
-			#size-cells = <0>;
+			phys = <&usbphy 1>;
+			phy-names = "host";
 			status = "disabled";
-
-			port@0 {
-				reg = <0>;
-				phys = <&usbphy 1>;
-			};
 		};
 
 		mfc: codec@f1700000 {
@@ -528,7 +514,7 @@
 			clock-names = "sclk_fimg2d", "fimg2d";
 		};
 
-		mdma1: mdma@fa200000 {
+		mdma1: dma-controller@fa200000 {
 			compatible = "arm,pl330", "arm,primecell";
 			reg = <0xfa200000 0x1000>;
 			interrupt-parent = <&vic0>;
@@ -536,8 +522,6 @@
 			clocks = <&clocks CLK_MDMA>;
 			clock-names = "apb_pclk";
 			#dma-cells = <1>;
-			#dma-channels = <8>;
-			#dma-requests = <1>;
 		};
 
 		rotator: rotator@fa300000 {
diff --git a/arch/arm/boot/dts/sam9x60.dtsi b/arch/arm/boot/dts/sam9x60.dtsi
index ec45ced3cde6..8f5477e307dd 100644
--- a/arch/arm/boot/dts/sam9x60.dtsi
+++ b/arch/arm/boot/dts/sam9x60.dtsi
@@ -12,6 +12,7 @@
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/clock/at91.h>
+#include <dt-bindings/mfd/at91-usart.h>
 #include <dt-bindings/mfd/atmel-flexcom.h>
 
 / {
@@ -270,7 +271,7 @@
 				clock-names = "pclk", "gclk";
 			};
 
-			sha: sha@f002c000 {
+			sha: crypto@f002c000 {
 				compatible = "atmel,at91sam9g46-sha";
 				reg = <0xf002c000 0x100>;
 				interrupts = <41 IRQ_TYPE_LEVEL_HIGH 0>;
@@ -280,7 +281,6 @@
 				dma-names = "tx";
 				clocks = <&pmc PMC_TYPE_PERIPHERAL 41>;
 				clock-names = "sha_clk";
-				status = "okay";
 			};
 
 			trng: trng@f0030000 {
@@ -288,10 +288,9 @@
 				reg = <0xf0030000 0x100>;
 				interrupts = <38 IRQ_TYPE_LEVEL_HIGH 0>;
 				clocks = <&pmc PMC_TYPE_PERIPHERAL 38>;
-				status = "okay";
 			};
 
-			aes: aes@f0034000 {
+			aes: crypto@f0034000 {
 				compatible = "atmel,at91sam9g46-aes";
 				reg = <0xf0034000 0x100>;
 				interrupts = <39 IRQ_TYPE_LEVEL_HIGH 0>;
@@ -304,10 +303,9 @@
 				dma-names = "tx", "rx";
 				clocks = <&pmc PMC_TYPE_PERIPHERAL 39>;
 				clock-names = "aes_clk";
-				status = "okay";
 			};
 
-			tdes: tdes@f0038000 {
+			tdes: crypto@f0038000 {
 				compatible = "atmel,at91sam9g46-tdes";
 				reg = <0xf0038000 0x100>;
 				interrupts = <40 IRQ_TYPE_LEVEL_HIGH 0>;
@@ -320,7 +318,6 @@
 				dma-names = "tx", "rx";
 				clocks = <&pmc PMC_TYPE_PERIPHERAL 40>;
 				clock-names = "tdes_clk";
-				status = "okay";
 			};
 
 			classd: classd@f003c000 {
@@ -468,7 +465,7 @@
 				interrupts = <18 IRQ_TYPE_LEVEL_HIGH 4>;
 				clocks = <&pmc PMC_TYPE_PERIPHERAL 18>;
 				#pwm-cells = <3>;
-				status="disabled";
+				status = "disabled";
 			};
 
 			hlcdc: hlcdc@f8038000 {
@@ -587,6 +584,7 @@
 			dbgu: serial@fffff200 {
 				compatible = "microchip,sam9x60-dbgu", "microchip,sam9x60-usart", "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
 				reg = <0xfffff200 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <47 IRQ_TYPE_LEVEL_HIGH 7>;
 				dmas = <&dma0
 					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
@@ -671,7 +669,7 @@
 				clock-names = "td_slck", "md_slck", "main_xtal";
 			};
 
-			reset_controller: rstc@fffffe00 {
+			reset_controller: reset-controller@fffffe00 {
 				compatible = "microchip,sam9x60-rstc";
 				reg = <0xfffffe00 0x10>;
 				clocks = <&clk32k 0>;
@@ -688,7 +686,7 @@
 				status = "disabled";
 			};
 
-			rtt: rtt@fffffe20 {
+			rtt: rtc@fffffe20 {
 				compatible = "microchip,sam9x60-rtt", "atmel,at91sam9260-rtt";
 				reg = <0xfffffe20 0x20>;
 				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
diff --git a/arch/arm/boot/dts/sama5d2.dtsi b/arch/arm/boot/dts/sama5d2.dtsi
index 801969c113d6..14c35c12a115 100644
--- a/arch/arm/boot/dts/sama5d2.dtsi
+++ b/arch/arm/boot/dts/sama5d2.dtsi
@@ -9,6 +9,7 @@
 #include <dt-bindings/dma/at91.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/clock/at91.h>
+#include <dt-bindings/mfd/at91-usart.h>
 #include <dt-bindings/iio/adc/at91-sama5d2_adc.h>
 
 / {
@@ -99,6 +100,16 @@
 		ranges = <0 0x00200000 0x20000>;
 	};
 
+	resistive_touch: resistive-touch {
+		compatible = "resistive-adc-touch";
+		io-channels = <&adc AT91_SAMA5D2_ADC_X_CHANNEL>,
+			      <&adc AT91_SAMA5D2_ADC_Y_CHANNEL>,
+			      <&adc AT91_SAMA5D2_ADC_P_CHANNEL>;
+		io-channel-names = "x", "y", "pressure";
+		touchscreen-min-pressure = <50000>;
+		status = "disabled";
+	};
+
 	ahb {
 		compatible = "simple-bus";
 		#address-cells = <1>;
@@ -288,6 +299,7 @@
 				reg-names = "qspi_base", "qspi_mmap";
 				interrupts = <52 IRQ_TYPE_LEVEL_HIGH 7>;
 				clocks = <&pmc PMC_TYPE_PERIPHERAL 52>;
+				clock-names = "pclk";
 				#address-cells = <1>;
 				#size-cells = <0>;
 				status = "disabled";
@@ -299,12 +311,13 @@
 				reg-names = "qspi_base", "qspi_mmap";
 				interrupts = <53 IRQ_TYPE_LEVEL_HIGH 7>;
 				clocks = <&pmc PMC_TYPE_PERIPHERAL 53>;
+				clock-names = "pclk";
 				#address-cells = <1>;
 				#size-cells = <0>;
 				status = "disabled";
 			};
 
-			sha@f0028000 {
+			sha: crypto@f0028000 {
 				compatible = "atmel,at91sam9g46-sha";
 				reg = <0xf0028000 0x100>;
 				interrupts = <12 IRQ_TYPE_LEVEL_HIGH 0>;
@@ -314,10 +327,9 @@
 				dma-names = "tx";
 				clocks = <&pmc PMC_TYPE_PERIPHERAL 12>;
 				clock-names = "sha_clk";
-				status = "okay";
 			};
 
-			aes@f002c000 {
+			aes: crypto@f002c000 {
 				compatible = "atmel,at91sam9g46-aes";
 				reg = <0xf002c000 0x100>;
 				interrupts = <9 IRQ_TYPE_LEVEL_HIGH 0>;
@@ -330,7 +342,6 @@
 				dma-names = "tx", "rx";
 				clocks = <&pmc PMC_TYPE_PERIPHERAL 9>;
 				clock-names = "aes_clk";
-				status = "okay";
 			};
 
 			spi0: spi@f8000000 {
@@ -374,8 +385,6 @@
 				interrupts = <5  IRQ_TYPE_LEVEL_HIGH 3		/* Queue 0 */
 					      66 IRQ_TYPE_LEVEL_HIGH 3          /* Queue 1 */
 					      67 IRQ_TYPE_LEVEL_HIGH 3>;        /* Queue 2 */
-				#address-cells = <1>;
-				#size-cells = <0>;
 				clocks = <&pmc PMC_TYPE_PERIPHERAL 5>, <&pmc PMC_TYPE_PERIPHERAL 5>;
 				clock-names = "hclk", "pclk";
 				status = "disabled";
@@ -413,7 +422,7 @@
 				pmecc: ecc-engine@f8014070 {
 					compatible = "atmel,sama5d2-pmecc";
 					reg = <0xf8014070 0x490>,
-					      <0xf8014500 0x100>;
+					      <0xf8014500 0x200>;
 				};
 			};
 
@@ -433,6 +442,7 @@
 			uart0: serial@f801c000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xf801c000 0x100>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <24 IRQ_TYPE_LEVEL_HIGH 7>;
 				dmas = <&dma0
 					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
@@ -449,6 +459,7 @@
 			uart1: serial@f8020000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xf8020000 0x100>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <25 IRQ_TYPE_LEVEL_HIGH 7>;
 				dmas = <&dma0
 					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
@@ -465,6 +476,7 @@
 			uart2: serial@f8024000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xf8024000 0x100>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <26 IRQ_TYPE_LEVEL_HIGH 7>;
 				dmas = <&dma0
 					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
@@ -522,6 +534,7 @@
 				uart5: serial@200 {
 					compatible = "atmel,at91sam9260-usart";
 					reg = <0x200 0x200>;
+					atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 					interrupts = <19 IRQ_TYPE_LEVEL_HIGH 7>;
 					clocks = <&pmc PMC_TYPE_PERIPHERAL 19>;
 					clock-names = "usart";
@@ -592,6 +605,7 @@
 				uart6: serial@200 {
 					compatible = "atmel,at91sam9260-usart";
 					reg = <0x200 0x200>;
+					atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 					interrupts = <20 IRQ_TYPE_LEVEL_HIGH 7>;
 					clocks = <&pmc PMC_TYPE_PERIPHERAL 20>;
 					clock-names = "usart";
@@ -660,7 +674,7 @@
 				ranges = <0 0xf8044000 0x1420>;
 			};
 
-			reset_controller: rstc@f8048000 {
+			reset_controller: reset-controller@f8048000 {
 				compatible = "atmel,sama5d3-rstc";
 				reg = <0xf8048000 0x10>;
 				clocks = <&clk32k>;
@@ -761,6 +775,7 @@
 			uart3: serial@fc008000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xfc008000 0x100>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <27 IRQ_TYPE_LEVEL_HIGH 7>;
 				dmas = <&dma1
 					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
@@ -777,6 +792,7 @@
 			uart4: serial@fc00c000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xfc00c000 0x100>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				dmas = <&dma0
 					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
 					 AT91_XDMAC_DT_PERID(43))>,
@@ -802,6 +818,7 @@
 				uart7: serial@200 {
 					compatible = "atmel,at91sam9260-usart";
 					reg = <0x200 0x200>;
+					atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 					interrupts = <21 IRQ_TYPE_LEVEL_HIGH 7>;
 					clocks = <&pmc PMC_TYPE_PERIPHERAL 21>;
 					clock-names = "usart";
@@ -872,6 +889,7 @@
 				uart8: serial@200 {
 					compatible = "atmel,at91sam9260-usart";
 					reg = <0x200 0x200>;
+					atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 					interrupts = <22 IRQ_TYPE_LEVEL_HIGH 7>;
 					clocks = <&pmc PMC_TYPE_PERIPHERAL 22>;
 					clock-names = "usart";
@@ -943,6 +961,7 @@
 				uart9: serial@200 {
 					compatible = "atmel,at91sam9260-usart";
 					reg = <0x200 0x200>;
+					atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 					interrupts = <23 IRQ_TYPE_LEVEL_HIGH 7>;
 					clocks = <&pmc PMC_TYPE_PERIPHERAL 23>;
 					clock-names = "usart";
@@ -1050,16 +1069,6 @@
 				status = "disabled";
 			};
 
-			resistive_touch: resistive-touch {
-				compatible = "resistive-adc-touch";
-				io-channels = <&adc AT91_SAMA5D2_ADC_X_CHANNEL>,
-					      <&adc AT91_SAMA5D2_ADC_Y_CHANNEL>,
-					      <&adc AT91_SAMA5D2_ADC_P_CHANNEL>;
-				io-channel-names = "x", "y", "pressure";
-				touchscreen-min-pressure = <50000>;
-				status = "disabled";
-			};
-
 			pioA: pinctrl@fc038000 {
 				compatible = "atmel,sama5d2-pinctrl";
 				reg = <0xfc038000 0x600>;
@@ -1082,7 +1091,7 @@
 				#gpio-cells = <2>;
 			};
 
-			tdes@fc044000 {
+			tdes: crypto@fc044000 {
 				compatible = "atmel,at91sam9g46-tdes";
 				reg = <0xfc044000 0x100>;
 				interrupts = <11 IRQ_TYPE_LEVEL_HIGH 0>;
@@ -1095,7 +1104,6 @@
 				dma-names = "tx", "rx";
 				clocks = <&pmc PMC_TYPE_PERIPHERAL 11>;
 				clock-names = "tdes_clk";
-				status = "okay";
 			};
 
 			classd: classd@fc048000 {
@@ -1125,7 +1133,7 @@
 				clocks = <&pmc PMC_TYPE_PERIPHERAL 55>, <&pmc PMC_TYPE_GCK 55>;
 				clock-names = "pclk", "gclk";
 				assigned-clocks = <&pmc PMC_TYPE_CORE PMC_I2S1_MUX>;
-				assigned-parrents = <&pmc PMC_TYPE_GCK 55>;
+				assigned-clock-parents = <&pmc PMC_TYPE_GCK 55>;
 				status = "disabled";
 			};
 
diff --git a/arch/arm/boot/dts/sama5d3.dtsi b/arch/arm/boot/dts/sama5d3.dtsi
index d1841bffe3c5..bde8e92d60bb 100644
--- a/arch/arm/boot/dts/sama5d3.dtsi
+++ b/arch/arm/boot/dts/sama5d3.dtsi
@@ -12,6 +12,7 @@
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/clock/at91.h>
+#include <dt-bindings/mfd/at91-usart.h>
 
 / {
 	#address-cells = <1>;
@@ -194,6 +195,7 @@
 			usart0: serial@f001c000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xf001c000 0x100>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <12 IRQ_TYPE_LEVEL_HIGH 5>;
 				dmas = <&dma0 2 AT91_DMA_CFG_PER_ID(3)>,
 				       <&dma0 2 (AT91_DMA_CFG_PER_ID(4) | AT91_DMA_CFG_FIFOCFG_ASAP)>;
@@ -208,6 +210,7 @@
 			usart1: serial@f0020000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xf0020000 0x100>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <13 IRQ_TYPE_LEVEL_HIGH 5>;
 				dmas = <&dma0 2 AT91_DMA_CFG_PER_ID(5)>,
 				       <&dma0 2 (AT91_DMA_CFG_PER_ID(6) | AT91_DMA_CFG_FIFOCFG_ASAP)>;
@@ -222,6 +225,7 @@
 			uart0: serial@f0024000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xf0024000 0x100>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <16 IRQ_TYPE_LEVEL_HIGH 5>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_uart0>;
@@ -356,6 +360,7 @@
 			usart2: serial@f8020000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xf8020000 0x100>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <14 IRQ_TYPE_LEVEL_HIGH 5>;
 				dmas = <&dma1 2 AT91_DMA_CFG_PER_ID(7)>,
 				       <&dma1 2 (AT91_DMA_CFG_PER_ID(8) | AT91_DMA_CFG_FIFOCFG_ASAP)>;
@@ -370,6 +375,7 @@
 			usart3: serial@f8024000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xf8024000 0x100>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <15 IRQ_TYPE_LEVEL_HIGH 5>;
 				dmas = <&dma1 2 AT91_DMA_CFG_PER_ID(9)>,
 				       <&dma1 2 (AT91_DMA_CFG_PER_ID(10) | AT91_DMA_CFG_FIFOCFG_ASAP)>;
@@ -381,7 +387,7 @@
 				status = "disabled";
 			};
 
-			sha@f8034000 {
+			sha: crypto@f8034000 {
 				compatible = "atmel,at91sam9g46-sha";
 				reg = <0xf8034000 0x100>;
 				interrupts = <42 IRQ_TYPE_LEVEL_HIGH 0>;
@@ -391,7 +397,7 @@
 				clock-names = "sha_clk";
 			};
 
-			aes@f8038000 {
+			aes: crypto@f8038000 {
 				compatible = "atmel,at91sam9g46-aes";
 				reg = <0xf8038000 0x100>;
 				interrupts = <43 IRQ_TYPE_LEVEL_HIGH 0>;
@@ -402,7 +408,7 @@
 				clock-names = "aes_clk";
 			};
 
-			tdes@f803c000 {
+			tdes: crypto@f803c000 {
 				compatible = "atmel,at91sam9g46-tdes";
 				reg = <0xf803c000 0x100>;
 				interrupts = <44 IRQ_TYPE_LEVEL_HIGH 0>;
@@ -464,6 +470,7 @@
 			dbgu: serial@ffffee00 {
 				compatible = "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
 				reg = <0xffffee00 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <2 IRQ_TYPE_LEVEL_HIGH 7>;
 				dmas = <&dma1 2 AT91_DMA_CFG_PER_ID(13)>,
 				       <&dma1 2 (AT91_DMA_CFG_PER_ID(14) | AT91_DMA_CFG_FIFOCFG_ASAP)>;
@@ -1003,7 +1010,7 @@
 				clock-names = "slow_clk", "main_xtal";
 			};
 
-			reset_controller: rstc@fffffe00 {
+			reset_controller: reset-controller@fffffe00 {
 				compatible = "atmel,sama5d3-rstc", "atmel,at91sam9g45-rstc";
 				reg = <0xfffffe00 0x10>;
 				clocks = <&clk32k>;
diff --git a/arch/arm/boot/dts/sama5d3_uart.dtsi b/arch/arm/boot/dts/sama5d3_uart.dtsi
index a3eaba995cf4..44d1173f2ffb 100644
--- a/arch/arm/boot/dts/sama5d3_uart.dtsi
+++ b/arch/arm/boot/dts/sama5d3_uart.dtsi
@@ -9,6 +9,7 @@
 #include <dt-bindings/pinctrl/at91.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/clock/at91.h>
+#include <dt-bindings/mfd/at91-usart.h>
 
 / {
 	aliases {
@@ -39,6 +40,7 @@
 			uart0: serial@f0024000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xf0024000 0x100>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <16 IRQ_TYPE_LEVEL_HIGH 5>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_uart0>;
@@ -50,6 +52,7 @@
 			uart1: serial@f8028000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xf8028000 0x100>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <17 IRQ_TYPE_LEVEL_HIGH 5>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_uart1>;
diff --git a/arch/arm/boot/dts/sama5d3xmb.dtsi b/arch/arm/boot/dts/sama5d3xmb.dtsi
index a499de8a7a64..3652c9e24124 100644
--- a/arch/arm/boot/dts/sama5d3xmb.dtsi
+++ b/arch/arm/boot/dts/sama5d3xmb.dtsi
@@ -26,7 +26,7 @@
 			spi0: spi@f0004000 {
 				dmas = <0>, <0>;	/*  Do not use DMA for spi0 */
 
-				m25p80@0 {
+				flash@0 {
 					compatible = "atmel,at25df321a";
 					spi-max-frequency = <50000000>;
 					reg = <0>;
diff --git a/arch/arm/boot/dts/sama5d3xmb_cmp.dtsi b/arch/arm/boot/dts/sama5d3xmb_cmp.dtsi
index fa9e5e2a745d..5d9e97fecf83 100644
--- a/arch/arm/boot/dts/sama5d3xmb_cmp.dtsi
+++ b/arch/arm/boot/dts/sama5d3xmb_cmp.dtsi
@@ -25,7 +25,7 @@
 			spi0: spi@f0004000 {
 				dmas = <0>, <0>;	/*  Do not use DMA for spi0 */
 
-				m25p80@0 {
+				flash@0 {
 					compatible = "atmel,at25df321a";
 					spi-max-frequency = <50000000>;
 					reg = <0>;
diff --git a/arch/arm/boot/dts/sama5d4.dtsi b/arch/arm/boot/dts/sama5d4.dtsi
index f6e3e6f57252..af62157ae214 100644
--- a/arch/arm/boot/dts/sama5d4.dtsi
+++ b/arch/arm/boot/dts/sama5d4.dtsi
@@ -8,6 +8,7 @@
 
 #include <dt-bindings/clock/at91.h>
 #include <dt-bindings/dma/at91.h>
+#include <dt-bindings/mfd/at91-usart.h>
 #include <dt-bindings/pinctrl/at91.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/gpio/gpio.h>
@@ -278,6 +279,7 @@
 			uart0: serial@f8004000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xf8004000 0x100>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <27 IRQ_TYPE_LEVEL_HIGH 5>;
 				dmas = <&dma0
 					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
@@ -437,6 +439,7 @@
 			usart0: serial@f802c000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xf802c000 0x100>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <6 IRQ_TYPE_LEVEL_HIGH 5>;
 				dmas = <&dma0
 					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
@@ -455,6 +458,7 @@
 			usart1: serial@f8030000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xf8030000 0x100>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <7 IRQ_TYPE_LEVEL_HIGH 5>;
 				dmas = <&dma0
 					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
@@ -490,6 +494,7 @@
 			uart1: serial@fc004000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xfc004000 0x100>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <28 IRQ_TYPE_LEVEL_HIGH 5>;
 				dmas = <&dma0
 					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
@@ -508,6 +513,7 @@
 			usart2: serial@fc008000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xfc008000 0x100>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <29 IRQ_TYPE_LEVEL_HIGH 5>;
 				dmas = <&dma1
 					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
@@ -526,6 +532,7 @@
 			usart3: serial@fc00c000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xfc00c000 0x100>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <30 IRQ_TYPE_LEVEL_HIGH 5>;
 				dmas = <&dma1
 					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
@@ -544,6 +551,7 @@
 			usart4: serial@fc010000 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0xfc010000 0x100>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <31 IRQ_TYPE_LEVEL_HIGH 5>;
 				dmas = <&dma1
 					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
@@ -673,7 +681,7 @@
 				status = "disabled";
 			};
 
-			aes@fc044000 {
+			aes: crypto@fc044000 {
 				compatible = "atmel,at91sam9g46-aes";
 				reg = <0xfc044000 0x100>;
 				interrupts = <12 IRQ_TYPE_LEVEL_HIGH 0>;
@@ -684,10 +692,9 @@
 				dma-names = "tx", "rx";
 				clocks = <&pmc PMC_TYPE_PERIPHERAL 12>;
 				clock-names = "aes_clk";
-				status = "okay";
 			};
 
-			tdes@fc04c000 {
+			tdes: crpyto@fc04c000 {
 				compatible = "atmel,at91sam9g46-tdes";
 				reg = <0xfc04c000 0x100>;
 				interrupts = <14 IRQ_TYPE_LEVEL_HIGH 0>;
@@ -698,10 +705,9 @@
 				dma-names = "tx", "rx";
 				clocks = <&pmc PMC_TYPE_PERIPHERAL 14>;
 				clock-names = "tdes_clk";
-				status = "okay";
 			};
 
-			sha@fc050000 {
+			sha: crypto@fc050000 {
 				compatible = "atmel,at91sam9g46-sha";
 				reg = <0xfc050000 0x100>;
 				interrupts = <15 IRQ_TYPE_LEVEL_HIGH 0>;
@@ -710,7 +716,6 @@
 				dma-names = "tx";
 				clocks = <&pmc PMC_TYPE_PERIPHERAL 15>;
 				clock-names = "sha_clk";
-				status = "okay";
 			};
 
 			hsmc: smc@fc05c000 {
@@ -729,7 +734,7 @@
 				};
 			};
 
-			reset_controller: rstc@fc068600 {
+			reset_controller: reset-controller@fc068600 {
 				compatible = "atmel,sama5d3-rstc", "atmel,at91sam9g45-rstc";
 				reg = <0xfc068600 0x10>;
 				clocks = <&clk32k>;
@@ -773,6 +778,7 @@
 			dbgu: serial@fc069000 {
 				compatible = "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
 				reg = <0xfc069000 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <45 IRQ_TYPE_LEVEL_HIGH 7>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_dbgu>;
diff --git a/arch/arm/boot/dts/sama7g5-pinfunc.h b/arch/arm/boot/dts/sama7g5-pinfunc.h
index 22fe9e522a97..4eb30445d205 100644
--- a/arch/arm/boot/dts/sama7g5-pinfunc.h
+++ b/arch/arm/boot/dts/sama7g5-pinfunc.h
@@ -765,7 +765,7 @@
 #define PIN_PD20__PCK0			PINMUX_PIN(PIN_PD20, 1, 3)
 #define PIN_PD20__FLEXCOM2_IO3		PINMUX_PIN(PIN_PD20, 2, 2)
 #define PIN_PD20__PWMH3			PINMUX_PIN(PIN_PD20, 3, 4)
-#define PIN_PD20__CANTX4		PINMUX_PIN(PIN_PD20, 5, 2)
+#define PIN_PD20__CANTX4		PINMUX_PIN(PIN_PD20, 4, 2)
 #define PIN_PD20__FLEXCOM5_IO0		PINMUX_PIN(PIN_PD20, 6, 5)
 #define PIN_PD21			117
 #define PIN_PD21__GPIO			PINMUX_PIN(PIN_PD21, 0, 0)
diff --git a/arch/arm/boot/dts/sama7g5.dtsi b/arch/arm/boot/dts/sama7g5.dtsi
index 7039311bf678..7bd8ae8e8d38 100644
--- a/arch/arm/boot/dts/sama7g5.dtsi
+++ b/arch/arm/boot/dts/sama7g5.dtsi
@@ -14,6 +14,7 @@
 #include <dt-bindings/clock/at91.h>
 #include <dt-bindings/dma/at91.h>
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/mfd/at91-usart.h>
 
 / {
 	model = "Microchip SAMA7G5 family SoC";
@@ -30,6 +31,44 @@
 			device_type = "cpu";
 			compatible = "arm,cortex-a7";
 			reg = <0x0>;
+			clocks = <&pmc PMC_TYPE_CORE PMC_CPUPLL>;
+			clock-names = "cpu";
+			operating-points-v2 = <&cpu_opp_table>;
+		};
+	};
+
+	cpu_opp_table: opp-table {
+		compatible = "operating-points-v2";
+
+		opp-90000000 {
+			opp-hz = /bits/ 64 <90000000>;
+			opp-microvolt = <1050000 1050000 1225000>;
+			clock-latency-ns = <320000>;
+		};
+
+		opp-250000000 {
+			opp-hz = /bits/ 64 <250000000>;
+			opp-microvolt = <1050000 1050000 1225000>;
+			clock-latency-ns = <320000>;
+		};
+
+		opp-600000000 {
+			opp-hz = /bits/ 64 <600000000>;
+			opp-microvolt = <1050000 1050000 1225000>;
+			clock-latency-ns = <320000>;
+			opp-suspend;
+		};
+
+		opp-800000000 {
+			opp-hz = /bits/ 64 <800000000>;
+			opp-microvolt = <1150000 1125000 1225000>;
+			clock-latency-ns = <320000>;
+		};
+
+		opp-1000000002 {
+			opp-hz = /bits/ 64 <1000000002>;
+			opp-microvolt = <1250000 1225000 1300000>;
+			clock-latency-ns = <320000>;
 		};
 	};
 
@@ -75,6 +114,45 @@
 		#size-cells = <1>;
 		ranges;
 
+		nfc_sram: sram@600000 {
+			compatible = "mmio-sram";
+			no-memory-wc;
+			reg = <0x00600000 0x2400>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x00600000 0x2400>;
+		};
+
+		nfc_io: nfc-io@10000000 {
+			compatible = "atmel,sama5d3-nfc-io", "syscon";
+			reg = <0x10000000 0x8000000>;
+		};
+
+		ebi: ebi@40000000 {
+			compatible = "atmel,sama5d3-ebi";
+			#address-cells = <2>;
+			#size-cells = <1>;
+			atmel,smc = <&hsmc>;
+			reg = <0x40000000 0x20000000>;
+			ranges = <0x0 0x0 0x40000000 0x8000000
+				  0x1 0x0 0x48000000 0x8000000
+				  0x2 0x0 0x50000000 0x8000000
+				  0x3 0x0 0x58000000 0x8000000>;
+			clocks = <&pmc PMC_TYPE_CORE PMC_MCK1>;
+			status = "disabled";
+
+			nand_controller: nand-controller {
+				compatible = "atmel,sama5d3-nand-controller";
+				atmel,nfc-sram = <&nfc_sram>;
+				atmel,nfc-io = <&nfc_io>;
+				ecc-engine = <&pmecc>;
+				#address-cells = <2>;
+				#size-cells = <1>;
+				ranges;
+				status = "disabled";
+			};
+		};
+
 		securam: securam@e0000000 {
 			compatible = "microchip,sama7g5-securam", "atmel,sama5d2-securam", "mmio-sram";
 			reg = <0xe0000000 0x4000>;
@@ -83,7 +161,6 @@
 			#size-cells = <1>;
 			ranges = <0 0xe0000000 0x4000>;
 			no-memory-wc;
-			status = "okay";
 		};
 
 		secumod: secumod@e0004000 {
@@ -122,6 +199,13 @@
 			clock-names = "td_slck", "md_slck", "main_xtal";
 		};
 
+		reset_controller: reset-controller@e001d000 {
+			compatible = "microchip,sama7g5-rstc";
+			reg = <0xe001d000 0xc>, <0xe001d0e4 0x4>;
+			#reset-cells = <1>;
+			clocks = <&clk32k 0>;
+		};
+
 		shdwc: shdwc@e001d010 {
 			compatible = "microchip,sama7g5-shdwc", "syscon";
 			reg = <0xe001d010 0x10>;
@@ -133,7 +217,7 @@
 			status = "disabled";
 		};
 
-		rtt: rtt@e001d020 {
+		rtt: rtc@e001d020 {
 			compatible = "microchip,sama7g5-rtt", "microchip,sam9x60-rtt", "atmel,at91sam9260-rtt";
 			reg = <0xe001d020 0x30>;
 			interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
@@ -181,6 +265,148 @@
 			clock-names = "t0_clk", "t1_clk", "t2_clk", "slow_clk";
 		};
 
+		hsmc: hsmc@e0808000 {
+			compatible = "atmel,sama5d2-smc", "syscon", "simple-mfd";
+			reg = <0xe0808000 0x1000>;
+			interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 21>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			pmecc: ecc-engine@e0808070 {
+				compatible = "atmel,sama5d2-pmecc";
+				reg = <0xe0808070 0x490>,
+				      <0xe0808500 0x200>;
+			};
+		};
+
+		qspi0: spi@e080c000 {
+			compatible = "microchip,sama7g5-ospi";
+			reg = <0xe080c000 0x400>, <0x20000000 0x10000000>;
+			reg-names = "qspi_base", "qspi_mmap";
+			interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
+			dmas = <&dma0 AT91_XDMAC_DT_PERID(41)>,
+			       <&dma0 AT91_XDMAC_DT_PERID(40)>;
+			dma-names = "tx", "rx";
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 78>, <&pmc PMC_TYPE_GCK 78>;
+			clock-names = "pclk", "gclk";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		qspi1: spi@e0810000 {
+			compatible = "microchip,sama7g5-qspi";
+			reg = <0xe0810000 0x400>, <0x30000000 0x10000000>;
+			reg-names = "qspi_base", "qspi_mmap";
+			interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
+			dmas = <&dma0 AT91_XDMAC_DT_PERID(43)>,
+			       <&dma0 AT91_XDMAC_DT_PERID(42)>;
+			dma-names = "tx", "rx";
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 79>, <&pmc PMC_TYPE_GCK 79>;
+			clock-names = "pclk", "gclk";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		can0: can@e0828000 {
+			compatible = "bosch,m_can";
+			reg = <0xe0828000 0x100>, <0x100000 0x7800>;
+			reg-names = "m_can", "message_ram";
+			interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "int0", "int1";
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 61>, <&pmc PMC_TYPE_GCK 61>;
+			clock-names = "hclk", "cclk";
+			assigned-clocks = <&pmc PMC_TYPE_GCK 61>;
+			assigned-clock-parents = <&pmc PMC_TYPE_CORE PMC_SYSPLL>;
+			assigned-clock-rates = <40000000>;
+			bosch,mram-cfg = <0x3400 0 0 64 0 0 32 32>;
+			status = "disabled";
+		};
+
+		can1: can@e082c000 {
+			compatible = "bosch,m_can";
+			reg = <0xe082c000 0x100>, <0x100000 0xbc00>;
+			reg-names = "m_can", "message_ram";
+			interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "int0", "int1";
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 62>, <&pmc PMC_TYPE_GCK 62>;
+			clock-names = "hclk", "cclk";
+			assigned-clocks = <&pmc PMC_TYPE_GCK 62>;
+			assigned-clock-parents = <&pmc PMC_TYPE_CORE PMC_SYSPLL>;
+			assigned-clock-rates = <40000000>;
+			bosch,mram-cfg = <0x7800 0 0 64 0 0 32 32>;
+			status = "disabled";
+		};
+
+		can2: can@e0830000 {
+			compatible = "bosch,m_can";
+			reg = <0xe0830000 0x100>, <0x100000 0x10000>;
+			reg-names = "m_can", "message_ram";
+			interrupts = <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "int0", "int1";
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 63>, <&pmc PMC_TYPE_GCK 63>;
+			clock-names = "hclk", "cclk";
+			assigned-clocks = <&pmc PMC_TYPE_GCK 63>;
+			assigned-clock-parents = <&pmc PMC_TYPE_CORE PMC_SYSPLL>;
+			assigned-clock-rates = <40000000>;
+			bosch,mram-cfg = <0xbc00 0 0 64 0 0 32 32>;
+			status = "disabled";
+		};
+
+		can3: can@e0834000 {
+			compatible = "bosch,m_can";
+			reg = <0xe0834000 0x100>, <0x110000 0x4400>;
+			reg-names = "m_can", "message_ram";
+			interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "int0", "int1";
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 64>, <&pmc PMC_TYPE_GCK 64>;
+			clock-names = "hclk", "cclk";
+			assigned-clocks = <&pmc PMC_TYPE_GCK 64>;
+			assigned-clock-parents = <&pmc PMC_TYPE_CORE PMC_SYSPLL>;
+			assigned-clock-rates = <40000000>;
+			bosch,mram-cfg = <0x0 0 0 64 0 0 32 32>;
+			status = "disabled";
+		};
+
+		can4: can@e0838000 {
+			compatible = "bosch,m_can";
+			reg = <0xe0838000 0x100>, <0x110000 0x8800>;
+			reg-names = "m_can", "message_ram";
+			interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "int0", "int1";
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 65>, <&pmc PMC_TYPE_GCK 65>;
+			clock-names = "hclk", "cclk";
+			assigned-clocks = <&pmc PMC_TYPE_GCK 65>;
+			assigned-clock-parents = <&pmc PMC_TYPE_CORE PMC_SYSPLL>;
+			assigned-clock-rates = <40000000>;
+			bosch,mram-cfg = <0x4400 0 0 64 0 0 32 32>;
+			status = "disabled";
+		};
+
+		can5: can@e083c000 {
+			compatible = "bosch,m_can";
+			reg = <0xe083c000 0x100>, <0x110000 0xcc00>;
+			reg-names = "m_can", "message_ram";
+			interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH
+				      GIC_SPI 128 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "int0", "int1";
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 66>, <&pmc PMC_TYPE_GCK 66>;
+			clock-names = "hclk", "cclk";
+			assigned-clocks = <&pmc PMC_TYPE_GCK 66>;
+			assigned-clock-parents = <&pmc PMC_TYPE_CORE PMC_SYSPLL>;
+			assigned-clock-rates = <40000000>;
+			bosch,mram-cfg = <0x8800 0 0 64 0 0 32 32>;
+			status = "disabled";
+		};
+
 		adc: adc@e1000000 {
 			compatible = "microchip,sama7g5-adc";
 			reg = <0xe1000000 0x200>;
@@ -245,6 +471,30 @@
 			status = "disabled";
 		};
 
+		pdmc0: sound@e1608000 {
+			compatible = "microchip,sama7g5-pdmc";
+			reg = <0xe1608000 0x1000>;
+			interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>;
+			#sound-dai-cells = <0>;
+			dmas = <&dma0 AT91_XDMAC_DT_PERID(37)>;
+			dma-names = "rx";
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 68>, <&pmc PMC_TYPE_GCK 68>;
+			clock-names = "pclk", "gclk";
+			status = "disabled";
+		};
+
+		pdmc1: sound@e160c000 {
+			compatible = "microchip,sama7g5-pdmc";
+			reg = <0xe160c000 0x1000>;
+			interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>;
+			#sound-dai-cells = <0>;
+			dmas = <&dma0 AT91_XDMAC_DT_PERID(38)>;
+			dma-names = "rx";
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 69>, <&pmc PMC_TYPE_GCK 69>;
+			clock-names = "pclk", "gclk";
+			status = "disabled";
+		};
+
 		spdifrx: spdifrx@e1614000 {
 			#sound-dai-cells = <0>;
 			compatible = "microchip,sama7g5-spdifrx";
@@ -292,6 +542,19 @@
 			status = "disabled";
 		};
 
+		eic: interrupt-controller@e1628000 {
+			compatible = "microchip,sama7g5-eic";
+			reg = <0xe1628000 0xec>;
+			interrupt-parent = <&gic>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			interrupts = <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 37>;
+			clock-names = "pclk";
+			status = "disabled";
+		};
+
 		pit64b0: timer@e1800000 {
 			compatible = "microchip,sama7g5-pit64b", "microchip,sam9x60-pit64b";
 			reg = <0xe1800000 0x4000>;
@@ -308,6 +571,27 @@
 			clock-names = "pclk", "gclk";
 		};
 
+		aes: crypto@e1810000 {
+			compatible = "atmel,at91sam9g46-aes";
+			reg = <0xe1810000 0x100>;
+			interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 27>;
+			clock-names = "aes_clk";
+			dmas = <&dma0 AT91_XDMAC_DT_PERID(1)>,
+			       <&dma0 AT91_XDMAC_DT_PERID(2)>;
+			dma-names = "tx", "rx";
+		};
+
+		sha: crypto@e1814000 {
+			compatible = "atmel,at91sam9g46-sha";
+			reg = <0xe1814000 0x100>;
+			interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 83>;
+			clock-names = "sha_clk";
+			dmas = <&dma0 AT91_XDMAC_DT_PERID(48)>;
+			dma-names = "tx";
+		};
+
 		flx0: flexcom@e1818000 {
 			compatible = "atmel,sama5d2-flexcom";
 			reg = <0xe1818000 0x200>;
@@ -320,6 +604,7 @@
 			uart0: serial@200 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0x200 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&pmc PMC_TYPE_PERIPHERAL 38>;
 				clock-names = "usart";
@@ -349,11 +634,9 @@
 				#size-cells = <0>;
 				clocks = <&pmc PMC_TYPE_PERIPHERAL 39>;
 				atmel,fifo-size = <32>;
-				dmas = <&dma0 AT91_XDMAC_DT_PERID(7)>,
-					<&dma0 AT91_XDMAC_DT_PERID(8)>;
-				dma-names = "rx", "tx";
-				atmel,use-dma-rx;
-				atmel,use-dma-tx;
+				dmas = <&dma0 AT91_XDMAC_DT_PERID(8)>,
+					<&dma0 AT91_XDMAC_DT_PERID(7)>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 		};
@@ -370,6 +653,7 @@
 			uart3: serial@200 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0x200 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&pmc PMC_TYPE_PERIPHERAL 41>;
 				clock-names = "usart";
@@ -390,6 +674,17 @@
 			status = "disabled";
 		};
 
+		tdes: crypto@e2014000 {
+			compatible = "atmel,at91sam9g46-tdes";
+			reg = <0xe2014000 0x100>;
+			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 96>;
+			clock-names = "tdes_clk";
+			dmas = <&dma0 AT91_XDMAC_DT_PERID(54)>,
+			       <&dma0 AT91_XDMAC_DT_PERID(53)>;
+			dma-names = "tx", "rx";
+		};
+
 		flx4: flexcom@e2018000 {
 			compatible = "atmel,sama5d2-flexcom";
 			reg = <0xe2018000 0x200>;
@@ -402,6 +697,7 @@
 			uart4: serial@200 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0x200 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&pmc PMC_TYPE_PERIPHERAL 42>;
 				clock-names = "usart";
@@ -427,6 +723,7 @@
 			uart7: serial@200 {
 				compatible = "atmel,at91sam9260-usart";
 				reg = <0x200 0x200>;
+				atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
 				interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&pmc PMC_TYPE_PERIPHERAL 45>;
 				clock-names = "usart";
@@ -525,11 +822,9 @@
 				#size-cells = <0>;
 				clocks = <&pmc PMC_TYPE_PERIPHERAL 46>;
 				atmel,fifo-size = <32>;
-				dmas = <&dma0 AT91_XDMAC_DT_PERID(21)>,
-					<&dma0 AT91_XDMAC_DT_PERID(22)>;
-				dma-names = "rx", "tx";
-				atmel,use-dma-rx;
-				atmel,use-dma-tx;
+				dmas = <&dma0 AT91_XDMAC_DT_PERID(22)>,
+					<&dma0 AT91_XDMAC_DT_PERID(21)>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 		};
@@ -551,11 +846,9 @@
 				#size-cells = <0>;
 				clocks = <&pmc PMC_TYPE_PERIPHERAL 47>;
 				atmel,fifo-size = <32>;
-				dmas = <&dma0 AT91_XDMAC_DT_PERID(23)>,
-					<&dma0 AT91_XDMAC_DT_PERID(24)>;
-				dma-names = "rx", "tx";
-				atmel,use-dma-rx;
-				atmel,use-dma-tx;
+				dmas = <&dma0 AT91_XDMAC_DT_PERID(24)>,
+					<&dma0 AT91_XDMAC_DT_PERID(23)>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 		};
@@ -578,9 +871,9 @@
 				#address-cells = <1>;
 				#size-cells = <0>;
 				atmel,fifo-size = <32>;
-				dmas = <&dma0 AT91_XDMAC_DT_PERID(27)>,
-					    <&dma0 AT91_XDMAC_DT_PERID(28)>;
-				dma-names = "rx", "tx";
+				dmas = <&dma0 AT91_XDMAC_DT_PERID(28)>,
+					    <&dma0 AT91_XDMAC_DT_PERID(27)>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 		};
@@ -588,13 +881,11 @@
 		uddrc: uddrc@e3800000 {
 			compatible = "microchip,sama7g5-uddrc";
 			reg = <0xe3800000 0x4000>;
-			status = "okay";
 		};
 
 		ddr3phy: ddr3phy@e3804000 {
 			compatible = "microchip,sama7g5-ddr3phy";
 			reg = <0xe3804000 0x1000>;
-			status = "okay";
 		};
 
 		gic: interrupt-controller@e8c11000 {
@@ -602,7 +893,6 @@
 			#interrupt-cells = <3>;
 			#address-cells = <0>;
 			interrupt-controller;
-			interrupt-parent;
 			reg = <0xe8c11000 0x1000>,
 				<0xe8c12000 0x2000>;
 		};
diff --git a/arch/arm/boot/dts/sd5203.dts b/arch/arm/boot/dts/sd5203.dts
index a61a078ea042..69381819e07b 100644
--- a/arch/arm/boot/dts/sd5203.dts
+++ b/arch/arm/boot/dts/sd5203.dts
@@ -15,7 +15,7 @@
 	#size-cells = <1>;
 
 	chosen {
-		bootargs="console=ttyS0,9600 earlycon=uart8250,mmio32,0x1600d000";
+		bootargs = "console=ttyS0,9600 earlycon=uart8250,mmio32,0x1600d000";
 	};
 
 	aliases {
diff --git a/arch/arm/boot/dts/socfpga.dtsi b/arch/arm/boot/dts/socfpga.dtsi
index 0b021eef0b53..2459f3cd7dd9 100644
--- a/arch/arm/boot/dts/socfpga.dtsi
+++ b/arch/arm/boot/dts/socfpga.dtsi
@@ -46,7 +46,7 @@
 		      <0xff113000 0x1000>;
 	};
 
-	intc: intc@fffed000 {
+	intc: interrupt-controller@fffed000 {
 		compatible = "arm,cortex-a9-gic";
 		#interrupt-cells = <3>;
 		interrupt-controller;
@@ -80,8 +80,6 @@
 					     <0 110 4>,
 					     <0 111 4>;
 				#dma-cells = <1>;
-				#dma-channels = <8>;
-				#dma-requests = <32>;
 				clocks = <&l4_main_clk>;
 				clock-names = "apb_pclk";
 				resets = <&rst DMA_RESET>;
@@ -563,6 +561,12 @@
 			interrupts = <0 175 4>;
 		};
 
+		socfpga_axi_setup: stmmac-axi-config {
+			snps,wr_osr_lmt = <0xf>;
+			snps,rd_osr_lmt = <0xf>;
+			snps,blen = <0 0 0 0 16 0 0>;
+		};
+
 		gmac0: ethernet@ff700000 {
 			compatible = "altr,socfpga-stmmac", "snps,dwmac-3.70a", "snps,dwmac";
 			altr,sysmgr-syscon = <&sysmgr 0x60 0>;
@@ -578,6 +582,7 @@
 			snps,perfect-filter-entries = <128>;
 			tx-fifo-depth = <4096>;
 			rx-fifo-depth = <4096>;
+			snps,axi-config = <&socfpga_axi_setup>;
 			status = "disabled";
 		};
 
@@ -596,6 +601,7 @@
 			snps,perfect-filter-entries = <128>;
 			tx-fifo-depth = <4096>;
 			rx-fifo-depth = <4096>;
+			snps,axi-config = <&socfpga_axi_setup>;
 			status = "disabled";
 		};
 
@@ -782,7 +788,7 @@
 		};
 
 		qspi: spi@ff705000 {
-			compatible = "cdns,qspi-nor";
+			compatible = "intel,socfpga-qspi", "cdns,qspi-nor";
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <0xff705000 0x1000>,
diff --git a/arch/arm/boot/dts/socfpga_arria10.dtsi b/arch/arm/boot/dts/socfpga_arria10.dtsi
index a574ea91d9d3..4370e3cbbb4b 100644
--- a/arch/arm/boot/dts/socfpga_arria10.dtsi
+++ b/arch/arm/boot/dts/socfpga_arria10.dtsi
@@ -38,7 +38,7 @@
 		      <0xff113000 0x1000>;
 	};
 
-	intc: intc@ffffd000 {
+	intc: interrupt-controller@ffffd000 {
 		compatible = "arm,cortex-a9-gic";
 		#interrupt-cells = <3>;
 		interrupt-controller;
@@ -73,8 +73,6 @@
 					     <0 90 IRQ_TYPE_LEVEL_HIGH>,
 					     <0 91 IRQ_TYPE_LEVEL_HIGH>;
 				#dma-cells = <1>;
-				#dma-channels = <8>;
-				#dma-requests = <32>;
 				clocks = <&l4_main_clk>;
 				clock-names = "apb_pclk";
 				resets = <&rst DMA_RESET>, <&rst DMA_OCP_RESET>;
@@ -738,6 +736,16 @@
 					     <37 IRQ_TYPE_LEVEL_HIGH>;
 			};
 
+			sdmmca-ecc@ff8c2c00 {
+				compatible = "altr,socfpga-sdmmc-ecc";
+				reg = <0xff8c2c00 0x400>;
+				altr,ecc-parent = <&mmc>;
+				interrupts = <15 IRQ_TYPE_LEVEL_HIGH>,
+					     <47 IRQ_TYPE_LEVEL_HIGH>,
+					     <16 IRQ_TYPE_LEVEL_HIGH>,
+					     <48 IRQ_TYPE_LEVEL_HIGH>;
+			};
+
 			dma-ecc@ff8c8000 {
 				compatible = "altr,socfpga-dma-ecc";
 				reg = <0xff8c8000 0x400>;
@@ -756,7 +764,7 @@
 		};
 
 		qspi: spi@ff809000 {
-			compatible = "cdns,qspi-nor";
+			compatible = "intel,socfpga-qspi", "cdns,qspi-nor";
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <0xff809000 0x100>,
diff --git a/arch/arm/boot/dts/socfpga_arria10_chameleonv3.dts b/arch/arm/boot/dts/socfpga_arria10_chameleonv3.dts
new file mode 100644
index 000000000000..422d00cd4c74
--- /dev/null
+++ b/arch/arm/boot/dts/socfpga_arria10_chameleonv3.dts
@@ -0,0 +1,90 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright 2022 Google LLC
+ */
+/dts-v1/;
+#include "socfpga_arria10_mercury_aa1.dtsi"
+
+/ {
+	model = "Google Chameleon V3";
+	compatible = "google,chameleon-v3", "enclustra,mercury-aa1",
+		     "altr,socfpga-arria10", "altr,socfpga";
+
+	aliases {
+		serial0 = &uart0;
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+	};
+};
+
+&gmac0 {
+	status = "okay";
+};
+
+&gpio0 {
+	status = "okay";
+};
+
+&gpio1 {
+	status = "okay";
+};
+
+&gpio2 {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	ssm2603: audio-codec@1a {
+		compatible = "adi,ssm2603";
+		reg = <0x1a>;
+	};
+};
+
+&i2c1 {
+	status = "okay";
+
+	u80: gpio@21 {
+		compatible = "nxp,pca9535";
+		reg = <0x21>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names =
+			"SOM_AUD_MUTE",
+			"DP1_OUT_CEC_EN",
+			"DP2_OUT_CEC_EN",
+			"DP1_SOM_PS8469_CAD",
+			"DPD_SOM_PS8469_CAD",
+			"DP_OUT_PWR_EN",
+			"STM32_RST_L",
+			"STM32_BOOT0",
+
+			"FPGA_PROT",
+			"STM32_FPGA_COMM0",
+			"TP119",
+			"TP120",
+			"TP121",
+			"TP122",
+			"TP123",
+			"TP124";
+	};
+};
+
+&mmc {
+	status = "okay";
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&usb0 {
+	status = "okay";
+	dr_mode = "host";
+};
diff --git a/arch/arm/boot/dts/socfpga_arria10_mercury_aa1.dts b/arch/arm/boot/dts/socfpga_arria10_mercury_aa1.dts
deleted file mode 100644
index 2a3364b26361..000000000000
--- a/arch/arm/boot/dts/socfpga_arria10_mercury_aa1.dts
+++ /dev/null
@@ -1,112 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/dts-v1/;
-
-#include "socfpga_arria10.dtsi"
-
-/ {
-
-	model = "Enclustra Mercury AA1";
-	compatible = "altr,socfpga-arria10", "altr,socfpga";
-
-	aliases {
-		ethernet0 = &gmac0;
-		serial1 = &uart1;
-		i2c0 = &i2c0;
-		i2c1 = &i2c1;
-	};
-
-	memory@0 {
-		name = "memory";
-		device_type = "memory";
-		reg = <0x0 0x80000000>; /* 2GB */
-	};
-
-	chosen {
-		stdout-path = "serial1:115200n8";
-	};
-};
-
-&eccmgr {
-	sdmmca-ecc@ff8c2c00 {
-		compatible = "altr,socfpga-sdmmc-ecc";
-		reg = <0xff8c2c00 0x400>;
-		altr,ecc-parent = <&mmc>;
-		interrupts = <15 IRQ_TYPE_LEVEL_HIGH>,
-			     <47 IRQ_TYPE_LEVEL_HIGH>,
-			     <16 IRQ_TYPE_LEVEL_HIGH>,
-			     <48 IRQ_TYPE_LEVEL_HIGH>;
-	};
-};
-
-&gmac0 {
-	phy-mode = "rgmii";
-	phy-addr = <0xffffffff>; /* probe for phy addr */
-
-	max-frame-size = <3800>;
-	status = "okay";
-
-	phy-handle = <&phy3>;
-
-	mdio {
-		#address-cells = <1>;
-		#size-cells = <0>;
-		compatible = "snps,dwmac-mdio";
-		phy3: ethernet-phy@3 {
-			txd0-skew-ps = <0>; /* -420ps */
-			txd1-skew-ps = <0>; /* -420ps */
-			txd2-skew-ps = <0>; /* -420ps */
-			txd3-skew-ps = <0>; /* -420ps */
-			rxd0-skew-ps = <420>; /* 0ps */
-			rxd1-skew-ps = <420>; /* 0ps */
-			rxd2-skew-ps = <420>; /* 0ps */
-			rxd3-skew-ps = <420>; /* 0ps */
-			txen-skew-ps = <0>; /* -420ps */
-			txc-skew-ps = <1860>; /* 960ps */
-			rxdv-skew-ps = <420>; /* 0ps */
-			rxc-skew-ps = <1680>; /* 780ps */
-			reg = <3>;
-		};
-	};
-};
-
-&gpio0 {
-	status = "okay";
-};
-
-&gpio1 {
-	status = "okay";
-};
-
-&gpio2 {
-	status = "okay";
-};
-
-&i2c1 {
-	status = "okay";
-	isl12022: isl12022@6f {
-		status = "okay";
-		compatible = "isil,isl12022";
-		reg = <0x6f>;
-	};
-};
-
-/* Following mappings are taken from arria10 socdk dts */
-&mmc {
-	status = "okay";
-	cap-sd-highspeed;
-	broken-cd;
-	bus-width = <4>;
-};
-
-&osc1 {
-	clock-frequency = <33330000>;
-};
-
-&uart1 {
-	status = "okay";
-};
-
-&usb0 {
-	status = "okay";
-	dr_mode = "host";
-};
diff --git a/arch/arm/boot/dts/socfpga_arria10_mercury_aa1.dtsi b/arch/arm/boot/dts/socfpga_arria10_mercury_aa1.dtsi
new file mode 100644
index 000000000000..ad7cd14de6b6
--- /dev/null
+++ b/arch/arm/boot/dts/socfpga_arria10_mercury_aa1.dtsi
@@ -0,0 +1,80 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright 2022 Google LLC
+ */
+
+#include "socfpga_arria10.dtsi"
+
+/ {
+
+	model = "Enclustra Mercury AA1";
+	compatible = "enclustra,mercury-aa1", "altr,socfpga-arria10", "altr,socfpga";
+
+	aliases {
+		ethernet0 = &gmac0;
+		serial1 = &uart1;
+	};
+
+	memory@0 {
+		name = "memory";
+		device_type = "memory";
+		reg = <0x0 0x80000000>; /* 2GB */
+	};
+
+	chosen {
+		stdout-path = "serial1:115200n8";
+	};
+};
+
+&gmac0 {
+	phy-mode = "rgmii";
+	phy-addr = <0xffffffff>; /* probe for phy addr */
+
+	max-frame-size = <3800>;
+
+	phy-handle = <&phy3>;
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+		phy3: ethernet-phy@3 {
+			txd0-skew-ps = <0>; /* -420ps */
+			txd1-skew-ps = <0>; /* -420ps */
+			txd2-skew-ps = <0>; /* -420ps */
+			txd3-skew-ps = <0>; /* -420ps */
+			rxd0-skew-ps = <420>; /* 0ps */
+			rxd1-skew-ps = <420>; /* 0ps */
+			rxd2-skew-ps = <420>; /* 0ps */
+			rxd3-skew-ps = <420>; /* 0ps */
+			txen-skew-ps = <0>; /* -420ps */
+			txc-skew-ps = <1860>; /* 960ps */
+			rxdv-skew-ps = <420>; /* 0ps */
+			rxc-skew-ps = <1680>; /* 780ps */
+			reg = <3>;
+		};
+	};
+};
+
+&i2c1 {
+	atsha204a: crypto@64 {
+		compatible = "atmel,atsha204a";
+		reg = <0x64>;
+	};
+
+	isl12022: isl12022@6f {
+		compatible = "isil,isl12022";
+		reg = <0x6f>;
+	};
+};
+
+/* Following mappings are taken from arria10 socdk dts */
+&mmc {
+	cap-sd-highspeed;
+	broken-cd;
+	bus-width = <4>;
+};
+
+&osc1 {
+	clock-frequency = <33330000>;
+};
diff --git a/arch/arm/boot/dts/socfpga_arria10_socdk.dtsi b/arch/arm/boot/dts/socfpga_arria10_socdk.dtsi
index 7edebe20e859..ec7365444a3b 100644
--- a/arch/arm/boot/dts/socfpga_arria10_socdk.dtsi
+++ b/arch/arm/boot/dts/socfpga_arria10_socdk.dtsi
@@ -6,7 +6,7 @@
 
 / {
 	model = "Altera SOCFPGA Arria 10";
-	compatible = "altr,socfpga-arria10", "altr,socfpga";
+	compatible = "altr,socfpga-arria10-socdk", "altr,socfpga-arria10", "altr,socfpga";
 
 	aliases {
 		ethernet0 = &gmac0;
diff --git a/arch/arm/boot/dts/socfpga_arria10_socdk_qspi.dts b/arch/arm/boot/dts/socfpga_arria10_socdk_qspi.dts
index 2b645642b935..11ccdc6c2dc6 100644
--- a/arch/arm/boot/dts/socfpga_arria10_socdk_qspi.dts
+++ b/arch/arm/boot/dts/socfpga_arria10_socdk_qspi.dts
@@ -9,10 +9,10 @@
 &qspi {
 	status = "okay";
 
-	flash0: n25q00@0 {
+	flash0: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		compatible = "n25q00aa";
+		compatible = "micron,mt25qu02g", "jedec,spi-nor";
 		reg = <0>;
 		spi-max-frequency = <100000000>;
 
diff --git a/arch/arm/boot/dts/socfpga_arria5_socdk.dts b/arch/arm/boot/dts/socfpga_arria5_socdk.dts
index 90e676e7019f..7f5458d8fccc 100644
--- a/arch/arm/boot/dts/socfpga_arria5_socdk.dts
+++ b/arch/arm/boot/dts/socfpga_arria5_socdk.dts
@@ -7,7 +7,7 @@
 
 / {
 	model = "Altera SOCFPGA Arria V SoC Development Kit";
-	compatible = "altr,socfpga-arria5", "altr,socfpga";
+	compatible = "altr,socfpga-arria5-socdk", "altr,socfpga-arria5", "altr,socfpga";
 
 	chosen {
 		bootargs = "earlyprintk";
@@ -50,7 +50,7 @@
 		};
 	};
 
-	regulator_3_3v: 3-3-v-regulator {
+	regulator_3_3v: regulator {
 		compatible = "regulator-fixed";
 		regulator-name = "3.3V";
 		regulator-min-microvolt = <3300000>;
@@ -119,7 +119,7 @@
 	flash: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		compatible = "n25q256a";
+		compatible = "micron,n25q256a", "jedec,spi-nor";
 		reg = <0>;
 		spi-max-frequency = <100000000>;
 
diff --git a/arch/arm/boot/dts/socfpga_cyclone5_chameleon96.dts b/arch/arm/boot/dts/socfpga_cyclone5_chameleon96.dts
index f6561766d83f..76262f1e5e03 100644
--- a/arch/arm/boot/dts/socfpga_cyclone5_chameleon96.dts
+++ b/arch/arm/boot/dts/socfpga_cyclone5_chameleon96.dts
@@ -24,7 +24,7 @@
 		reg = <0x0 0x20000000>; /* 512MB */
 	};
 
-	regulator_3_3v: 3-3-v-regulator {
+	regulator_3_3v: regulator {
 		compatible = "regulator-fixed";
 		regulator-name = "3.3V";
 		regulator-min-microvolt = <3300000>;
diff --git a/arch/arm/boot/dts/socfpga_cyclone5_de0_nano_soc.dts b/arch/arm/boot/dts/socfpga_cyclone5_de0_nano_soc.dts
index 67076e1b1c7f..c8f051fb2bf6 100644
--- a/arch/arm/boot/dts/socfpga_cyclone5_de0_nano_soc.dts
+++ b/arch/arm/boot/dts/socfpga_cyclone5_de0_nano_soc.dts
@@ -24,7 +24,7 @@
 		ethernet0 = &gmac1;
 	};
 
-	regulator_3_3v: 3-3-v-regulator {
+	regulator_3_3v: regulator {
 		compatible = "regulator-fixed";
 		regulator-name = "3.3V";
 		regulator-min-microvolt = <3300000>;
diff --git a/arch/arm/boot/dts/socfpga_cyclone5_socdk.dts b/arch/arm/boot/dts/socfpga_cyclone5_socdk.dts
index 6f138b2b2616..b2241205c7a9 100644
--- a/arch/arm/boot/dts/socfpga_cyclone5_socdk.dts
+++ b/arch/arm/boot/dts/socfpga_cyclone5_socdk.dts
@@ -50,7 +50,7 @@
 		};
 	};
 
-	regulator_3_3v: 3-3-v-regulator {
+	regulator_3_3v: regulator {
 		compatible = "regulator-fixed";
 		regulator-name = "3.3V";
 		regulator-min-microvolt = <3300000>;
@@ -121,10 +121,10 @@
 &qspi {
 	status = "okay";
 
-	flash0: n25q00@0 {
+	flash0: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		compatible = "n25q00";
+		compatible = "micron,mt25qu02g", "jedec,spi-nor";
 		reg = <0>;	/* chip select */
 		spi-max-frequency = <100000000>;
 
diff --git a/arch/arm/boot/dts/socfpga_cyclone5_sockit.dts b/arch/arm/boot/dts/socfpga_cyclone5_sockit.dts
index c155ff02eb6e..3dd99c7c95e0 100644
--- a/arch/arm/boot/dts/socfpga_cyclone5_sockit.dts
+++ b/arch/arm/boot/dts/socfpga_cyclone5_sockit.dts
@@ -111,7 +111,7 @@
 		};
 	};
 
-	regulator_3_3v: vcc3p3-regulator {
+	regulator_3_3v: regulator {
 		compatible = "regulator-fixed";
 		regulator-name = "VCC3P3";
 		regulator-min-microvolt = <3300000>;
@@ -169,7 +169,7 @@
 	flash: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		compatible = "n25q00";
+		compatible = "micron,mt25qu02g", "jedec,spi-nor";
 		reg = <0>;
 		spi-max-frequency = <100000000>;
 
diff --git a/arch/arm/boot/dts/socfpga_cyclone5_socrates.dts b/arch/arm/boot/dts/socfpga_cyclone5_socrates.dts
index 8d5d3996f6f2..ca18b959e655 100644
--- a/arch/arm/boot/dts/socfpga_cyclone5_socrates.dts
+++ b/arch/arm/boot/dts/socfpga_cyclone5_socrates.dts
@@ -80,7 +80,7 @@
 	flash: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		compatible = "n25q256a";
+		compatible = "micron,n25q256a", "jedec,spi-nor";
 		reg = <0>;
 		spi-max-frequency = <100000000>;
 		m25p,fast-read;
diff --git a/arch/arm/boot/dts/socfpga_cyclone5_sodia.dts b/arch/arm/boot/dts/socfpga_cyclone5_sodia.dts
index 99a71757cdf4..2564671fc1c6 100644
--- a/arch/arm/boot/dts/socfpga_cyclone5_sodia.dts
+++ b/arch/arm/boot/dts/socfpga_cyclone5_sodia.dts
@@ -26,7 +26,7 @@
 		ethernet0 = &gmac1;
 	};
 
-	regulator_3_3v: 3-3-v-regulator {
+	regulator_3_3v: regulator {
 		compatible = "regulator-fixed";
 		regulator-name = "3.3V";
 		regulator-min-microvolt = <3300000>;
@@ -113,10 +113,10 @@
 &qspi {
 	status = "okay";
 
-	flash0: n25q512a@0 {
+	flash0: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		compatible = "n25q512a";
+		compatible = "micron,n25q512a", "jedec,spi-nor";
 		reg = <0>;
 		spi-max-frequency = <100000000>;
 
diff --git a/arch/arm/boot/dts/socfpga_cyclone5_vining_fpga.dts b/arch/arm/boot/dts/socfpga_cyclone5_vining_fpga.dts
index a060718758b6..f24f17c2f5ee 100644
--- a/arch/arm/boot/dts/socfpga_cyclone5_vining_fpga.dts
+++ b/arch/arm/boot/dts/socfpga_cyclone5_vining_fpga.dts
@@ -221,10 +221,10 @@
 &qspi {
 	status = "okay";
 
-	n25q128@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		compatible = "n25q128";
+		compatible = "micron,n25q128", "jedec,spi-nor";
 		reg = <0>;		/* chip select */
 		spi-max-frequency = <100000000>;
 		m25p,fast-read;
@@ -238,10 +238,10 @@
 		cdns,tslch-ns = <4>;
 	};
 
-	n25q00@1 {
+	flash@1 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		compatible = "n25q00";
+		compatible = "micron,mt25qu02g", "jedec,spi-nor";
 		reg = <1>;		/* chip select */
 		spi-max-frequency = <100000000>;
 		m25p,fast-read;
diff --git a/arch/arm/boot/dts/spear1310-evb.dts b/arch/arm/boot/dts/spear1310-evb.dts
index 8fcb6be6e7c7..05408df38203 100644
--- a/arch/arm/boot/dts/spear1310-evb.dts
+++ b/arch/arm/boot/dts/spear1310-evb.dts
@@ -170,7 +170,7 @@
 
 		smi: flash@ea000000 {
 			status = "okay";
-			clock-rate=<50000000>;
+			clock-rate = <50000000>;
 
 			flash@e6000000 {
 				#address-cells = <1>;
@@ -379,7 +379,7 @@
 					};
 				};
 
-				m25p80@1 {
+				flash@1 {
 					compatible = "st,m25p80";
 					reg = <1>;
 					spi-max-frequency = <12000000>;
@@ -395,22 +395,6 @@
 					pl022,wait-state = <0>;
 					pl022,duplex = <0>;
 				};
-
-				spidev@2 {
-					compatible = "spidev";
-					reg = <2>;
-					spi-max-frequency = <25000000>;
-					spi-cpha;
-					pl022,hierarchy = <0>;
-					pl022,interface = <0>;
-					pl022,slave-tx-disable;
-					pl022,com-mode = <0x2>;
-					pl022,rx-level-trig = <0>;
-					pl022,tx-level-trig = <0>;
-					pl022,ctrl-len = <0x11>;
-					pl022,wait-state = <0>;
-					pl022,duplex = <0>;
-				};
 			};
 
 			wdt@ec800620 {
diff --git a/arch/arm/boot/dts/spear1340-evb.dts b/arch/arm/boot/dts/spear1340-evb.dts
index f70ff56d4542..7700f2afc128 100644
--- a/arch/arm/boot/dts/spear1340-evb.dts
+++ b/arch/arm/boot/dts/spear1340-evb.dts
@@ -168,7 +168,7 @@
 
 		smi: flash@ea000000 {
 			status = "okay";
-			clock-rate=<50000000>;
+			clock-rate = <50000000>;
 
 			flash@e6000000 {
 				#address-cells = <1>;
@@ -439,7 +439,7 @@
 				cs-gpios = <&gpiopinctrl 80 0>, <&gpiopinctrl 24 0>,
 					   <&gpiopinctrl 85 0>;
 
-				m25p80@0 {
+				flash@0 {
 					compatible = "m25p80";
 					reg = <0>;
 					spi-max-frequency = <12000000>;
@@ -489,22 +489,6 @@
 						ts,i-drive = <1>;
 					};
 				};
-
-				spidev@2 {
-					compatible = "spidev";
-					reg = <2>;
-					spi-max-frequency = <25000000>;
-					spi-cpha;
-					pl022,hierarchy = <0>;
-					pl022,interface = <0>;
-					pl022,slave-tx-disable;
-					pl022,com-mode = <0x2>;
-					pl022,rx-level-trig = <0>;
-					pl022,tx-level-trig = <0>;
-					pl022,ctrl-len = <0x11>;
-					pl022,wait-state = <0>;
-					pl022,duplex = <0>;
-				};
 			};
 
 			timer@ec800600 {
diff --git a/arch/arm/boot/dts/spear1340.dtsi b/arch/arm/boot/dts/spear1340.dtsi
index 827e887afbda..818886e11713 100644
--- a/arch/arm/boot/dts/spear1340.dtsi
+++ b/arch/arm/boot/dts/spear1340.dtsi
@@ -88,7 +88,7 @@
 		};
 
 		pwm: pwm@e0180000 {
-			compatible ="st,spear13xx-pwm";
+			compatible = "st,spear13xx-pwm";
 			reg = <0xe0180000 0x1000>;
 			#pwm-cells = <2>;
 			status = "disabled";
@@ -134,9 +134,9 @@
 				reg = <0xb4100000 0x1000>;
 				interrupts = <0 105 0x4>;
 				status = "disabled";
-				dmas = <&dwdma0 12 0 1>,
-					<&dwdma0 13 1 0>;
-				dma-names = "tx", "rx";
+				dmas = <&dwdma0 13 0 1>,
+					<&dwdma0 12 1 0>;
+				dma-names = "rx", "tx";
 			};
 
 			thermal@e07008c4 {
diff --git a/arch/arm/boot/dts/spear13xx.dtsi b/arch/arm/boot/dts/spear13xx.dtsi
index c87b881b2c8b..913553367687 100644
--- a/arch/arm/boot/dts/spear13xx.dtsi
+++ b/arch/arm/boot/dts/spear13xx.dtsi
@@ -284,9 +284,9 @@
 				#size-cells = <0>;
 				interrupts = <0 31 0x4>;
 				status = "disabled";
-				dmas = <&dwdma0 4 0 0>,
-					<&dwdma0 5 0 0>;
-				dma-names = "tx", "rx";
+				dmas = <&dwdma0 5 0 0>,
+					<&dwdma0 4 0 0>;
+				dma-names = "rx", "tx";
 			};
 
 			rtc@e0580000 {
diff --git a/arch/arm/boot/dts/spear300-evb.dts b/arch/arm/boot/dts/spear300-evb.dts
index 2beb30ca2cba..303ef29fb805 100644
--- a/arch/arm/boot/dts/spear300-evb.dts
+++ b/arch/arm/boot/dts/spear300-evb.dts
@@ -80,7 +80,7 @@
 
 		smi: flash@fc000000 {
 			status = "okay";
-			clock-rate=<50000000>;
+			clock-rate = <50000000>;
 
 			flash@f8000000 {
 				#address-cells = <1>;
diff --git a/arch/arm/boot/dts/spear310-evb.dts b/arch/arm/boot/dts/spear310-evb.dts
index 1c41e4a40334..ea0b53036f7b 100644
--- a/arch/arm/boot/dts/spear310-evb.dts
+++ b/arch/arm/boot/dts/spear310-evb.dts
@@ -94,7 +94,7 @@
 
 		smi: flash@fc000000 {
 			status = "okay";
-			clock-rate=<50000000>;
+			clock-rate = <50000000>;
 
 			flash@f8000000 {
 				#address-cells = <1>;
diff --git a/arch/arm/boot/dts/spear310.dtsi b/arch/arm/boot/dts/spear310.dtsi
index 8ce751a1376d..77570833d46b 100644
--- a/arch/arm/boot/dts/spear310.dtsi
+++ b/arch/arm/boot/dts/spear310.dtsi
@@ -92,6 +92,7 @@
 			gpiopinctrl: gpio@b4000000 {
 				compatible = "st,spear-plgpio";
 				reg = <0xb4000000 0x1000>;
+				regmap = <&pinmux>;
 				#interrupt-cells = <1>;
 				interrupt-controller;
 				gpio-controller;
diff --git a/arch/arm/boot/dts/spear320-evb.dts b/arch/arm/boot/dts/spear320-evb.dts
index c322407a0ade..3c026d021c92 100644
--- a/arch/arm/boot/dts/spear320-evb.dts
+++ b/arch/arm/boot/dts/spear320-evb.dts
@@ -95,7 +95,7 @@
 
 		smi: flash@fc000000 {
 			status = "okay";
-			clock-rate=<50000000>;
+			clock-rate = <50000000>;
 
 			flash@f8000000 {
 				#address-cells = <1>;
diff --git a/arch/arm/boot/dts/spear320-hmi.dts b/arch/arm/boot/dts/spear320-hmi.dts
index 367ba48aac3e..34503ac9c51c 100644
--- a/arch/arm/boot/dts/spear320-hmi.dts
+++ b/arch/arm/boot/dts/spear320-hmi.dts
@@ -167,7 +167,7 @@
 
 		smi: flash@fc000000 {
 			status = "okay";
-			clock-rate=<50000000>;
+			clock-rate = <50000000>;
 
 			flash@f8000000 {
 				#address-cells = <1>;
@@ -235,7 +235,6 @@
 					#address-cells = <1>;
 					#size-cells = <0>;
 					reg = <0x41>;
-					irq-over-gpio;
 					irq-gpios = <&gpiopinctrl 29 0x4>;
 					id = <0>;
 					blocks = <0x5>;
diff --git a/arch/arm/boot/dts/spear320.dtsi b/arch/arm/boot/dts/spear320.dtsi
index 3bc1e93a0a55..b12474446a48 100644
--- a/arch/arm/boot/dts/spear320.dtsi
+++ b/arch/arm/boot/dts/spear320.dtsi
@@ -78,7 +78,7 @@
 		};
 
 		pwm: pwm@a8000000 {
-			compatible ="st,spear-pwm";
+			compatible = "st,spear-pwm";
 			reg = <0xa8000000 0x1000>;
 			#pwm-cells = <2>;
 			status = "disabled";
@@ -120,6 +120,7 @@
 			gpiopinctrl: gpio@b3000000 {
 				compatible = "st,spear-plgpio";
 				reg = <0xb3000000 0x1000>;
+				regmap = <&pinmux>;
 				#interrupt-cells = <1>;
 				interrupt-controller;
 				gpio-controller;
diff --git a/arch/arm/boot/dts/spear320s.dtsi b/arch/arm/boot/dts/spear320s.dtsi
new file mode 100644
index 000000000000..133236dc190d
--- /dev/null
+++ b/arch/arm/boot/dts/spear320s.dtsi
@@ -0,0 +1,24 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * DTS file for SPEAr320s SoC
+ *
+ * Copyright 2021 Herve Codina <herve.codina@bootlin.com>
+ */
+
+/include/ "spear320.dtsi"
+
+/ {
+	ahb {
+		apb {
+			gpiopinctrl: gpio@b3000000 {
+				/*
+				 * The "RM0321 SPEAr320s address and map
+				 * registers" document mentions interrupt 6
+				 * (NPGIO_INTR) for the PL_GPIO interrupt.
+				 */
+				interrupts = <6>;
+				interrupt-parent = <&shirq>;
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/ste-ab8500.dtsi b/arch/arm/boot/dts/ste-ab8500.dtsi
index 2cf19386a525..dd30d08ccb9b 100644
--- a/arch/arm/boot/dts/ste-ab8500.dtsi
+++ b/arch/arm/boot/dts/ste-ab8500.dtsi
@@ -28,26 +28,28 @@
 				interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
 				interrupt-controller;
 				#interrupt-cells = <2>;
+				#address-cells = <1>;
+				#size-cells = <0>;
 
 				ab8500_clock: clock-controller {
 					compatible = "stericsson,ab8500-clk";
 					#clock-cells = <1>;
 				};
 
-				ab8500_gpio: ab8500-gpiocontroller {
+				ab8500_gpio: gpio {
 					compatible = "stericsson,ab8500-gpio";
 					gpio-controller;
 					#gpio-cells = <2>;
 				};
 
-				ab8500-rtc {
+				rtc {
 					compatible = "stericsson,ab8500-rtc";
 					interrupts = <17 IRQ_TYPE_LEVEL_HIGH>,
 						     <18 IRQ_TYPE_LEVEL_HIGH>;
 					interrupt-names = "60S", "ALARM";
 				};
 
-				gpadc: ab8500-gpadc {
+				gpadc: adc {
 					compatible = "stericsson,ab8500-gpadc";
 					interrupts = <32 IRQ_TYPE_LEVEL_HIGH>,
 						     <39 IRQ_TYPE_LEVEL_HIGH>;
@@ -120,13 +122,10 @@
 					};
 				};
 
-				ab8500_temp {
+				thermal {
 					compatible = "stericsson,abx500-temp";
 					interrupts = <3 IRQ_TYPE_LEVEL_HIGH>;
 					interrupt-names = "ABX500_TEMP_WARM";
-					io-channels = <&gpadc 0x06>,
-						      <&gpadc 0x07>;
-					io-channel-names = "aux1", "aux2";
 				};
 
 				ab8500_fg {
@@ -196,7 +195,7 @@
 							  "CH_WD_EXP",
 							  "VBUS_CH_DROP_END";
 					monitored-battery = <&battery>;
-					vddadc-supply	= <&ab8500_ldo_tvout_reg>;
+					vddadc-supply = <&ab8500_ldo_tvout_reg>;
 					io-channels = <&gpadc 0x03>,
 						      <&gpadc 0x0a>,
 						      <&gpadc 0x09>,
@@ -208,11 +207,11 @@
 				};
 
 				ab8500_chargalg {
-					compatible	= "stericsson,ab8500-chargalg";
-					monitored-battery	= <&battery>;
+					compatible = "stericsson,ab8500-chargalg";
+					monitored-battery = <&battery>;
 				};
 
-				ab8500_usb: ab8500_usb {
+				ab8500_usb: phy {
 					compatible = "stericsson,ab8500-usb";
 					interrupts = <90 IRQ_TYPE_LEVEL_HIGH>,
 						     <96 IRQ_TYPE_LEVEL_HIGH>,
@@ -236,7 +235,7 @@
 					#phy-cells = <0>;
 				};
 
-				ab8500-ponkey {
+				key {
 					compatible = "stericsson,ab8500-poweron-key";
 					interrupts = <6 IRQ_TYPE_LEVEL_HIGH>,
 						     <7 IRQ_TYPE_LEVEL_HIGH>;
@@ -247,29 +246,31 @@
 					compatible = "stericsson,ab8500-sysctrl";
 				};
 
-				ab8500-pwm-1 {
+				pwm@1 {
 					compatible = "stericsson,ab8500-pwm";
+					reg = <1>;
 					clocks = <&ab8500_clock AB8500_SYSCLK_INT>;
 					clock-names = "intclk";
+					#pwm-cells = <1>;
 				};
 
-				ab8500-pwm-2 {
+				pwm@2 {
 					compatible = "stericsson,ab8500-pwm";
+					reg = <2>;
 					clocks = <&ab8500_clock AB8500_SYSCLK_INT>;
 					clock-names = "intclk";
+					#pwm-cells = <1>;
 				};
 
-				ab8500-pwm-3 {
+				pwm@3 {
 					compatible = "stericsson,ab8500-pwm";
+					reg = <3>;
 					clocks = <&ab8500_clock AB8500_SYSCLK_INT>;
 					clock-names = "intclk";
+					#pwm-cells = <1>;
 				};
 
-				ab8500-debugfs {
-					compatible = "stericsson,ab8500-debug";
-				};
-
-				codec: ab8500-codec {
+				codec: codec {
 					compatible = "stericsson,ab8500-codec";
 
 					V-AUD-supply = <&ab8500_ldo_audio_reg>;
@@ -283,7 +284,7 @@
 					stericsson,earpeice-cmv = <950>; /* Units in mV. */
 				};
 
-				ext_regulators: ab8500-ext-regulators {
+				ext_regulators: regulator-external {
 					compatible = "stericsson,ab8500-ext-regulator";
 
 					ab8500_ext1_reg: ab8500_ext1 {
@@ -307,7 +308,7 @@
 					};
 				};
 
-				ab8500-regulators {
+				regulator {
 					compatible = "stericsson,ab8500-regulator";
 					vin-supply = <&ab8500_ext3_reg>;
 
diff --git a/arch/arm/boot/dts/ste-ab8505.dtsi b/arch/arm/boot/dts/ste-ab8505.dtsi
index e98335e9d1cb..131c82508e82 100644
--- a/arch/arm/boot/dts/ste-ab8505.dtsi
+++ b/arch/arm/boot/dts/ste-ab8505.dtsi
@@ -25,26 +25,28 @@
 				interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
 				interrupt-controller;
 				#interrupt-cells = <2>;
+				#address-cells = <1>;
+				#size-cells = <0>;
 
 				ab8500_clock: clock-controller {
 					compatible = "stericsson,ab8500-clk";
 					#clock-cells = <1>;
 				};
 
-				ab8505_gpio: ab8505-gpiocontroller {
+				ab8505_gpio: gpio {
 					compatible = "stericsson,ab8505-gpio";
 					gpio-controller;
 					#gpio-cells = <2>;
 				};
 
-				ab8500-rtc {
+				rtc {
 					compatible = "stericsson,ab8500-rtc";
 					interrupts = <17 IRQ_TYPE_LEVEL_HIGH>,
 						     <18 IRQ_TYPE_LEVEL_HIGH>;
 					interrupt-names = "60S", "ALARM";
 				};
 
-				gpadc: ab8500-gpadc {
+				gpadc: adc {
 					compatible = "stericsson,ab8500-gpadc";
 					interrupts = <39 IRQ_TYPE_LEVEL_HIGH>;
 					interrupt-names = "SW_CONV_END";
@@ -92,8 +94,13 @@
 					};
 				};
 
+				thermal {
+					compatible = "stericsson,abx500-temp";
+					interrupts = <3 IRQ_TYPE_LEVEL_HIGH>;
+					interrupt-names = "ABX500_TEMP_WARM";
+				};
+
 				ab8500_fg {
-					status = "disabled";
 					compatible = "stericsson,ab8500-fg";
 					interrupts = <24 IRQ_TYPE_LEVEL_HIGH>,
 						     <8 IRQ_TYPE_LEVEL_HIGH>,
@@ -111,7 +118,6 @@
 				};
 
 				ab8500_btemp {
-					status = "disabled";
 					compatible = "stericsson,ab8500-btemp";
 					interrupts = <20 IRQ_TYPE_LEVEL_HIGH>,
 						     <80 IRQ_TYPE_LEVEL_HIGH>,
@@ -131,7 +137,6 @@
 				};
 
 				ab8500_charger {
-					status = "disabled";
 					compatible = "stericsson,ab8500-charger";
 					interrupts = <10 IRQ_TYPE_LEVEL_HIGH>,
 						     <11 IRQ_TYPE_LEVEL_HIGH>,
@@ -170,12 +175,11 @@
 				};
 
 				ab8500_chargalg {
-					status = "disabled";
 					compatible = "stericsson,ab8500-chargalg";
 					monitored-battery = <&battery>;
 				};
 
-				ab8500_usb: ab8500_usb {
+				ab8500_usb: phy {
 					compatible = "stericsson,ab8500-usb";
 					interrupts = <90 IRQ_TYPE_LEVEL_HIGH>,
 						     <96 IRQ_TYPE_LEVEL_HIGH>,
@@ -199,7 +203,7 @@
 					#phy-cells = <0>;
 				};
 
-				ab8500-ponkey {
+				key {
 					compatible = "stericsson,ab8500-poweron-key";
 					interrupts = <6 IRQ_TYPE_LEVEL_HIGH>,
 						     <7 IRQ_TYPE_LEVEL_HIGH>;
@@ -210,17 +214,15 @@
 					compatible = "stericsson,ab8500-sysctrl";
 				};
 
-				ab8500-pwm {
+				pwm@1 {
 					compatible = "stericsson,ab8500-pwm";
+					reg = <1>;
 					clocks = <&ab8500_clock AB8500_SYSCLK_INT>;
 					clock-names = "intclk";
+					#pwm-cells = <1>;
 				};
 
-				ab8500-debugfs {
-					compatible = "stericsson,ab8500-debug";
-				};
-
-				codec: ab8500-codec {
+				codec: codec {
 					compatible = "stericsson,ab8500-codec";
 
 					V-AUD-supply = <&ab8500_ldo_audio_reg>;
@@ -233,7 +235,7 @@
 					stericsson,earpeice-cmv = <950>; /* Units in mV. */
 				};
 
-				ab8505-regulators {
+				regulator {
 					compatible = "stericsson,ab8505-regulator";
 
 					ab8500_ldo_aux1_reg: ab8500_ldo_aux1 {
diff --git a/arch/arm/boot/dts/ste-dbx5x0.dtsi b/arch/arm/boot/dts/ste-dbx5x0.dtsi
index 68607e4ad80c..9afe8301bd47 100644
--- a/arch/arm/boot/dts/ste-dbx5x0.dtsi
+++ b/arch/arm/boot/dts/ste-dbx5x0.dtsi
@@ -5,6 +5,7 @@
 
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/reset/stericsson,db8500-prcc-reset.h>
 #include <dt-bindings/mfd/dbx500-prcmu.h>
 #include <dt-bindings/arm/ux500_pm_domains.h>
 #include <dt-bindings/gpio/gpio.h>
@@ -300,6 +301,10 @@
 				#clock-cells = <2>;
 			};
 
+			prcc_reset: prcc-reset-controller {
+				#reset-cells = <2>;
+			};
+
 			rtc_clk: rtc32k-clock {
 				#clock-cells = <0>;
 			};
@@ -656,12 +661,12 @@
 
 			#address-cells = <1>;
 			#size-cells = <0>;
-			v-i2c-supply = <&db8500_vape_reg>;
 
 			clock-frequency = <400000>;
 			clocks = <&prcc_kclk 3 3>, <&prcc_pclk 3 3>;
 			clock-names = "i2cclk", "apb_pclk";
 			power-domains = <&pm_domains DOMAIN_VAPE>;
+			resets = <&prcc_reset DB8500_PRCC_3 DB8500_PRCC_3_RESET_I2C0>;
 
 			status = "disabled";
 		};
@@ -673,13 +678,13 @@
 
 			#address-cells = <1>;
 			#size-cells = <0>;
-			v-i2c-supply = <&db8500_vape_reg>;
 
 			clock-frequency = <400000>;
 
 			clocks = <&prcc_kclk 1 2>, <&prcc_pclk 1 2>;
 			clock-names = "i2cclk", "apb_pclk";
 			power-domains = <&pm_domains DOMAIN_VAPE>;
+			resets = <&prcc_reset DB8500_PRCC_1 DB8500_PRCC_1_RESET_I2C1>;
 
 			status = "disabled";
 		};
@@ -691,13 +696,13 @@
 
 			#address-cells = <1>;
 			#size-cells = <0>;
-			v-i2c-supply = <&db8500_vape_reg>;
 
 			clock-frequency = <400000>;
 
 			clocks = <&prcc_kclk 1 6>, <&prcc_pclk 1 6>;
 			clock-names = "i2cclk", "apb_pclk";
 			power-domains = <&pm_domains DOMAIN_VAPE>;
+			resets = <&prcc_reset DB8500_PRCC_1 DB8500_PRCC_1_RESET_I2C2>;
 
 			status = "disabled";
 		};
@@ -709,13 +714,13 @@
 
 			#address-cells = <1>;
 			#size-cells = <0>;
-			v-i2c-supply = <&db8500_vape_reg>;
 
 			clock-frequency = <400000>;
 
 			clocks = <&prcc_kclk 2 0>, <&prcc_pclk 2 0>;
 			clock-names = "i2cclk", "apb_pclk";
 			power-domains = <&pm_domains DOMAIN_VAPE>;
+			resets = <&prcc_reset DB8500_PRCC_2 DB8500_PRCC_2_RESET_I2C3>;
 
 			status = "disabled";
 		};
@@ -727,13 +732,13 @@
 
 			#address-cells = <1>;
 			#size-cells = <0>;
-			v-i2c-supply = <&db8500_vape_reg>;
 
 			clock-frequency = <400000>;
 
 			clocks = <&prcc_kclk 1 9>, <&prcc_pclk 1 10>;
 			clock-names = "i2cclk", "apb_pclk";
 			power-domains = <&pm_domains DOMAIN_VAPE>;
+			resets = <&prcc_reset DB8500_PRCC_1 DB8500_PRCC_1_RESET_I2C4>;
 
 			status = "disabled";
 		};
@@ -745,11 +750,12 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 			clocks = <&prcc_kclk 3 1>, <&prcc_pclk 3 1>;
-			clock-names = "SSPCLK", "apb_pclk";
+			clock-names = "sspclk", "apb_pclk";
 			dmas = <&dma 8 0 0x2>, /* Logical - DevToMem */
 			       <&dma 8 0 0x0>; /* Logical - MemToDev */
 			dma-names = "rx", "tx";
 			power-domains = <&pm_domains DOMAIN_VAPE>;
+			resets = <&prcc_reset DB8500_PRCC_3 DB8500_PRCC_3_RESET_SSP0>;
 
 			status = "disabled";
 		};
@@ -761,11 +767,12 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 			clocks = <&prcc_kclk 3 2>, <&prcc_pclk 3 2>;
-			clock-names = "SSPCLK", "apb_pclk";
+			clock-names = "sspclk", "apb_pclk";
 			dmas = <&dma 9 0 0x2>, /* Logical - DevToMem */
 			       <&dma 9 0 0x0>; /* Logical - MemToDev */
 			dma-names = "rx", "tx";
 			power-domains = <&pm_domains DOMAIN_VAPE>;
+			resets = <&prcc_reset DB8500_PRCC_3 DB8500_PRCC_3_RESET_SSP1>;
 
 			status = "disabled";
 		};
@@ -778,7 +785,7 @@
 			#size-cells = <0>;
 			/* Same clock wired to kernel and pclk */
 			clocks = <&prcc_pclk 2 8>, <&prcc_pclk 2 8>;
-			clock-names = "SSPCLK", "apb_pclk";
+			clock-names = "sspclk", "apb_pclk";
 			dmas = <&dma 0 0 0x2>, /* Logical - DevToMem */
 			       <&dma 0 0 0x0>; /* Logical - MemToDev */
 			dma-names = "rx", "tx";
@@ -795,7 +802,7 @@
 			#size-cells = <0>;
 			/* Same clock wired to kernel and pclk */
 			clocks = <&prcc_pclk 2 2>, <&prcc_pclk 2 2>;
-			clock-names = "SSPCLK", "apb_pclk";
+			clock-names = "sspclk", "apb_pclk";
 			dmas = <&dma 35 0 0x2>, /* Logical - DevToMem */
 			       <&dma 35 0 0x0>; /* Logical - MemToDev */
 			dma-names = "rx", "tx";
@@ -812,7 +819,7 @@
 			#size-cells = <0>;
 			/* Same clock wired to kernel and pclk */
 			clocks = <&prcc_pclk 2 1>, <&prcc_pclk 2 1>;
-			clock-names = "SSPCLK", "apb_pclk";
+			clock-names = "sspclk", "apb_pclk";
 			dmas = <&dma 33 0 0x2>, /* Logical - DevToMem */
 			       <&dma 33 0 0x0>; /* Logical - MemToDev */
 			dma-names = "rx", "tx";
@@ -829,11 +836,12 @@
 			#size-cells = <0>;
 			/* Same clock wired to kernel and pclk */
 			clocks = <&prcc_pclk 1 7>, <&prcc_pclk 1 7>;
-			clock-names = "SSPCLK", "apb_pclk";
+			clock-names = "sspclk", "apb_pclk";
 			dmas = <&dma 40 0 0x2>, /* Logical - DevToMem */
 			       <&dma 40 0 0x0>; /* Logical - MemToDev */
 			dma-names = "rx", "tx";
 			power-domains = <&pm_domains DOMAIN_VAPE>;
+			resets = <&prcc_reset DB8500_PRCC_1 DB8500_PRCC_1_RESET_SPI3>;
 
 			status = "disabled";
 		};
@@ -849,6 +857,7 @@
 
 			clocks = <&prcc_kclk 1 0>, <&prcc_pclk 1 0>;
 			clock-names = "uart", "apb_pclk";
+			resets = <&prcc_reset DB8500_PRCC_1 DB8500_PRCC_1_RESET_UART0>;
 
 			status = "disabled";
 		};
@@ -864,6 +873,7 @@
 
 			clocks = <&prcc_kclk 1 1>, <&prcc_pclk 1 1>;
 			clock-names = "uart", "apb_pclk";
+			resets = <&prcc_reset DB8500_PRCC_1 DB8500_PRCC_1_RESET_UART1>;
 
 			status = "disabled";
 		};
@@ -879,6 +889,7 @@
 
 			clocks = <&prcc_kclk 3 6>, <&prcc_pclk 3 6>;
 			clock-names = "uart", "apb_pclk";
+			resets = <&prcc_reset DB8500_PRCC_3 DB8500_PRCC_3_RESET_UART2>;
 
 			status = "disabled";
 		};
@@ -895,6 +906,7 @@
 			clocks = <&prcc_kclk 1 5>, <&prcc_pclk 1 5>;
 			clock-names = "sdi", "apb_pclk";
 			power-domains = <&pm_domains DOMAIN_VAPE>;
+			resets = <&prcc_reset DB8500_PRCC_1 DB8500_PRCC_1_RESET_SDI0>;
 
 			status = "disabled";
 		};
@@ -911,6 +923,7 @@
 			clocks = <&prcc_kclk 2 4>, <&prcc_pclk 2 6>;
 			clock-names = "sdi", "apb_pclk";
 			power-domains = <&pm_domains DOMAIN_VAPE>;
+			resets = <&prcc_reset DB8500_PRCC_2 DB8500_PRCC_2_RESET_SDI1>;
 
 			status = "disabled";
 		};
@@ -927,6 +940,7 @@
 			clocks = <&prcc_kclk 3 4>, <&prcc_pclk 3 4>;
 			clock-names = "sdi", "apb_pclk";
 			power-domains = <&pm_domains DOMAIN_VAPE>;
+			resets = <&prcc_reset DB8500_PRCC_3 DB8500_PRCC_3_RESET_SDI2>;
 
 			status = "disabled";
 		};
@@ -943,6 +957,7 @@
 			clocks = <&prcc_kclk 2 5>, <&prcc_pclk 2 7>;
 			clock-names = "sdi", "apb_pclk";
 			power-domains = <&pm_domains DOMAIN_VAPE>;
+			resets = <&prcc_reset DB8500_PRCC_2 DB8500_PRCC_2_RESET_SDI3>;
 
 			status = "disabled";
 		};
@@ -959,6 +974,7 @@
 			clocks = <&prcc_kclk 2 2>, <&prcc_pclk 2 4>;
 			clock-names = "sdi", "apb_pclk";
 			power-domains = <&pm_domains DOMAIN_VAPE>;
+			resets = <&prcc_reset DB8500_PRCC_2 DB8500_PRCC_2_RESET_SDI4>;
 
 			status = "disabled";
 		};
@@ -975,6 +991,7 @@
 			clocks = <&prcc_kclk 3 7>, <&prcc_pclk 3 7>;
 			clock-names = "sdi", "apb_pclk";
 			power-domains = <&pm_domains DOMAIN_VAPE>;
+			resets = <&prcc_reset DB8500_PRCC_3 DB8500_PRCC_3_RESET_SDI5>;
 
 			status = "disabled";
 		};
@@ -996,6 +1013,7 @@
 
 			clocks = <&prcc_kclk 1 3>, <&prcc_pclk 1 3>;
 			clock-names = "msp", "apb_pclk";
+			resets = <&prcc_reset DB8500_PRCC_1 DB8500_PRCC_1_RESET_MSP0>;
 
 			status = "disabled";
 		};
@@ -1012,6 +1030,7 @@
 
 			clocks = <&prcc_kclk 1 4>, <&prcc_pclk 1 4>;
 			clock-names = "msp", "apb_pclk";
+			resets = <&prcc_reset DB8500_PRCC_1 DB8500_PRCC_1_RESET_MSP1>;
 
 			status = "disabled";
 		};
@@ -1030,6 +1049,7 @@
 
 			clocks = <&prcc_kclk 2 3>, <&prcc_pclk 2 5>;
 			clock-names = "msp", "apb_pclk";
+			resets = <&prcc_reset DB8500_PRCC_2 DB8500_PRCC_2_RESET_MSP2>;
 
 			status = "disabled";
 		};
@@ -1046,6 +1066,7 @@
 
 			clocks = <&prcc_kclk 1 10>, <&prcc_pclk 1 11>;
 			clock-names = "msp", "apb_pclk";
+			resets = <&prcc_reset DB8500_PRCC_1 DB8500_PRCC_1_RESET_MSP3>;
 
 			status = "disabled";
 		};
diff --git a/arch/arm/boot/dts/ste-href-ab8500.dtsi b/arch/arm/boot/dts/ste-href-ab8500.dtsi
index 3ccb7b5c7162..9fa024900d53 100644
--- a/arch/arm/boot/dts/ste-href-ab8500.dtsi
+++ b/arch/arm/boot/dts/ste-href-ab8500.dtsi
@@ -9,7 +9,7 @@
 	soc {
 		prcmu@80157000 {
 			ab8500 {
-				ab8500-gpiocontroller {
+				gpio {
 					/* Hog a few default settings */
 					pinctrl-names = "default";
 					pinctrl-0 = <&gpio2_default_mode>,
diff --git a/arch/arm/boot/dts/ste-href.dtsi b/arch/arm/boot/dts/ste-href.dtsi
index 718752a0248e..8f1bb78fc1e4 100644
--- a/arch/arm/boot/dts/ste-href.dtsi
+++ b/arch/arm/boot/dts/ste-href.dtsi
@@ -16,7 +16,32 @@
 	battery: battery {
 		compatible = "simple-battery";
 		battery-type = "lithium-ion-polymer";
-		thermistor-on-batctrl;
+	};
+
+	thermal-zones {
+		battery-thermal {
+			/* This zone will be polled by the battery temperature code */
+			polling-delay = <0>;
+			polling-delay-passive = <0>;
+			thermal-sensors = <&bat_therm>;
+
+			trips {
+				battery-crit-hi {
+					temperature = <70000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+	};
+
+	bat_therm: thermistor {
+		compatible = "murata,ncp18wb473";
+		io-channels = <&gpadc 0x02>; /* BatTemp */
+		pullup-uv = <1800000>;
+		pullup-ohm = <230000>;
+		pulldown-ohm = <0>;
+		#thermal-sensor-cells = <0>;
 	};
 
 	soc {
@@ -219,16 +244,16 @@
 
 		prcmu@80157000 {
 			ab8500 {
-				ab8500-gpiocontroller {
+				gpio {
 				};
 
-				ab8500_usb {
+				phy {
 					pinctrl-names = "default", "sleep";
 					pinctrl-0 = <&usb_a_1_default>;
 					pinctrl-1 = <&usb_a_1_sleep>;
 				};
 
-				ab8500-regulators {
+				regulator {
 					ab8500_ldo_aux1_reg: ab8500_ldo_aux1 {
 						regulator-name = "V-DISPLAY";
 					};
diff --git a/arch/arm/boot/dts/ste-hrefv60plus.dtsi b/arch/arm/boot/dts/ste-hrefv60plus.dtsi
index 8f504edefd3f..e66fa59c2de6 100644
--- a/arch/arm/boot/dts/ste-hrefv60plus.dtsi
+++ b/arch/arm/boot/dts/ste-hrefv60plus.dtsi
@@ -353,11 +353,11 @@
 					 * Drive DISP1 reset high (not reset), driver DISP2 reset low (reset)
 					 */
 					hrefv60_cfg1 {
-						pins ="GPIO65_F1";
+						pins = "GPIO65_F1";
 						ste,config = <&gpio_out_hi>;
 					};
 					hrefv60_cfg2 {
-						pins ="GPIO66_G3";
+						pins = "GPIO66_G3";
 						ste,config = <&gpio_out_lo>;
 					};
 				};
diff --git a/arch/arm/boot/dts/ste-snowball.dts b/arch/arm/boot/dts/ste-snowball.dts
index fb719c8a8eb2..e2f0cdacba7d 100644
--- a/arch/arm/boot/dts/ste-snowball.dts
+++ b/arch/arm/boot/dts/ste-snowball.dts
@@ -20,7 +20,32 @@
 	battery: battery {
 		compatible = "simple-battery";
 		battery-type = "lithium-ion-polymer";
-		thermistor-on-batctrl;
+	};
+
+	thermal-zones {
+		battery-thermal {
+			/* This zone will be polled by the battery temperature code */
+			polling-delay = <0>;
+			polling-delay-passive = <0>;
+			thermal-sensors = <&bat_therm>;
+
+			trips {
+				battery-crit-hi {
+					temperature = <70000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+	};
+
+	bat_therm: thermistor {
+		compatible = "murata,ncp18wb473";
+		io-channels = <&gpadc 0x02>; /* BatTemp */
+		pullup-uv = <1800000>;
+		pullup-ohm = <230000>;
+		pulldown-ohm = <0>;
+		#thermal-sensor-cells = <0>;
 	};
 
 	en_3v3_reg: en_3v3 {
@@ -384,7 +409,7 @@
 
 		prcmu@80157000 {
 			ab8500 {
-				ab8500-gpiocontroller {
+				gpio {
 					/*
 					 * AB8500 GPIOs are numbered starting from 1, so the first
 					 * index 0 is what in the datasheet is called "GPIO1", and
@@ -406,13 +431,13 @@
 						     "PM_GPIO42"; /* AB8500 GPIO42 */
 				};
 
-				ab8500_usb {
+				phy {
 					pinctrl-names = "default", "sleep";
 					pinctrl-0 = <&usb_a_1_default>;
 					pinctrl-1 = <&usb_a_1_sleep>;
 				};
 
-				ext_regulators: ab8500-ext-regulators {
+				ext_regulators: regulator-external {
 					ab8500_ext1_reg: ab8500_ext1 {
 						regulator-name = "ab8500-ext-supply1";
 					};
@@ -426,7 +451,7 @@
 					};
 				};
 
-				ab8500-regulators {
+				regulator {
 					ab8500_ldo_aux1_reg: ab8500_ldo_aux1 {
 						regulator-name = "V-DISPLAY";
 					};
diff --git a/arch/arm/boot/dts/ste-ux500-samsung-codina-tmo.dts b/arch/arm/boot/dts/ste-ux500-samsung-codina-tmo.dts
new file mode 100644
index 000000000000..27a3ab7e25e1
--- /dev/null
+++ b/arch/arm/boot/dts/ste-ux500-samsung-codina-tmo.dts
@@ -0,0 +1,793 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Devicetree for the Samsung Galaxy Exhibit SGH-T599 also known as Codina-TMO,
+ * the "TMO" shall be read "T-Mobile" as this phone was produced exlusively
+ * for T-Mobile in the United States.
+ *
+ * This phone is closely related to the Codina, but has:
+ * - No CPU speed cap, full ~1GHz rate
+ * - Different power management IC, AB8505
+ * - As AB8505 has a micro USB phy, no TI TSU6111
+ * - Different power routing such as the removal of the external LDO for the
+ *   touchscreen in favor of using the AB8505
+ * - Using a regulator for the key backlight LED
+ * - Using the Samsung S6D27A1 panel by default
+ * - The panel is using one of the ordinary AB8505 regulators for 1.8V
+ * - WiFi/Bluetooth combi chip upgraded to BCM4334
+ * - GPIO for backlight control moved from 68 to 69
+ */
+
+/dts-v1/;
+#include "ste-db8500.dtsi"
+#include "ste-ab8505.dtsi"
+#include "ste-dbx5x0-pinctrl.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	model = "Samsung Galaxy Exhibit (SGH-T599)";
+	compatible = "samsung,codina-tmo", "st-ericsson,u8500";
+
+	chosen {
+		stdout-path = &serial2;
+	};
+
+	battery: battery {
+		compatible = "samsung,eb425161lu";
+	};
+
+	thermal-zones {
+		battery-thermal {
+			/* This zone will be polled by the battery temperature code */
+			polling-delay = <0>;
+			polling-delay-passive = <0>;
+			thermal-sensors = <&bat_therm>;
+
+			trips {
+				battery-crit-hi {
+					temperature = <70000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+	};
+
+	bat_therm: thermistor {
+		compatible = "samsung,1404-001221";
+		io-channels = <&gpadc 0x02>; /* BatTemp */
+		pullup-uv = <1800000>;
+		pullup-ohm = <230000>;
+		pulldown-ohm = <0>;
+		#thermal-sensor-cells = <0>;
+	};
+
+	/* TI TXS0206 level translator for 2.9 V */
+	sd_level_translator: regulator-gpio {
+		compatible = "regulator-fixed";
+
+		/* GPIO87 EN */
+		gpios = <&gpio2 23 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		regulator-name = "sd-level-translator";
+		regulator-min-microvolt = <2900000>;
+		regulator-max-microvolt = <2900000>;
+		regulator-type = "voltage";
+
+		startup-delay-us = <200>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&sd_level_translator_default>;
+	};
+
+	/* External LDO MIC5366-3.3YMT for eMMC */
+	ldo_3v3_reg: regulator-gpio-ldo-3v3 {
+		compatible = "regulator-fixed";
+		/* Supplied in turn by VBAT */
+		regulator-name = "VMEM_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpios = <&gpio6 31 GPIO_ACTIVE_HIGH>;
+		startup-delay-us = <5000>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&emmc_ldo_en_default_mode>;
+	};
+
+	/*
+	 * External Ricoh RP152L010B-TR LCD LDO regulator for the display.
+	 * LCD_PWR_EN controls both the 3.0V output.
+	 */
+	lcd_3v0_reg: regulator-gpio-lcd-3v0 {
+		compatible = "regulator-fixed";
+		/* Supplied in turn by VBAT */
+		regulator-name = "VREG_LCD_3.0V";
+		regulator-min-microvolt = <3000000>;
+		regulator-max-microvolt = <3000000>;
+		/* GPIO219 controls this regulator */
+		gpio = <&gpio6 27 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&lcd_pwr_en_default_mode>;
+	};
+
+	/*
+	 * This regulator is a GPIO line that drives the Broadcom WLAN
+	 * line WL_REG_ON high and enables the internal regulators
+	 * inside the chip. Unfortunatley it is erroneously named
+	 * WLAN_RST_N on the schematic but it is not a reset line.
+	 *
+	 * The voltage specified here is only used to determine the OCR mask,
+	 * the for the SDIO connector, the chip is actually connected
+	 * directly to VBAT.
+	 */
+	wl_reg: regulator-gpio-wlan {
+		compatible = "regulator-fixed";
+		regulator-name = "WL_REG_ON";
+		regulator-min-microvolt = <3000000>;
+		regulator-max-microvolt = <3000000>;
+		startup-delay-us = <100000>;
+		/* GPIO215 (WLAN_RST_N to WL_REG_ON) */
+		gpio = <&gpio6 23 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&wlan_ldo_en_default>;
+	};
+
+	vibrator {
+		compatible = "gpio-vibrator";
+		/* GPIO195 "MOT_EN" */
+		enable-gpios = <&gpio6 3 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vibrator_default>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_keys_default_mode>;
+
+		button-home {
+			linux,code = <KEY_HOME>;
+			label = "HOME";
+			/* GPIO91 */
+			gpios = <&gpio2 27 GPIO_ACTIVE_LOW>;
+		};
+		button-volup {
+			linux,code = <KEY_VOLUMEUP>;
+			label = "VOL+";
+			/* GPIO67 */
+			gpios = <&gpio2 3 GPIO_ACTIVE_LOW>;
+		};
+		button-voldown {
+			linux,code = <KEY_VOLUMEDOWN>;
+			label = "VOL-";
+			/* GPIO92 */
+			gpios = <&gpio2 28 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	led-touchkeys {
+		compatible = "regulator-led";
+		vled-supply = <&ab8500_ldo_aux4_reg>; // 3.3V
+		default-state = "on";
+		function = LED_FUNCTION_KBD_BACKLIGHT;
+		color = <LED_COLOR_ID_WHITE>;
+	};
+
+	ktd253: backlight {
+		compatible = "kinetic,ktd253";
+		/* GPIO69 is used on Codina R0.4 and Codina TMO */
+		enable-gpios = <&gpio2 5 GPIO_ACTIVE_HIGH>;
+		/* Default to 13/32 brightness */
+		default-brightness = <13>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&ktd253_backlight_default_mode>;
+	};
+
+	/* Richtek RT8515GQW Flash LED Driver IC */
+	flash {
+		compatible = "richtek,rt8515";
+		/* GPIO 140 */
+		enf-gpios = <&gpio4 12 GPIO_ACTIVE_HIGH>;
+		/* GPIO 141 */
+		ent-gpios = <&gpio4 13 GPIO_ACTIVE_HIGH>;
+		/*
+		 * RFS is 16 kOhm and RTS is 100 kOhm giving
+		 * the flash max current 343mA and torch max
+		 * current 55 mA.
+		 */
+		richtek,rfs-ohms = <16000>;
+		richtek,rts-ohms = <100000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_flash_default_mode>;
+
+		led {
+			function = LED_FUNCTION_FLASH;
+			color = <LED_COLOR_ID_WHITE>;
+			flash-max-timeout-us = <250000>;
+			flash-max-microamp = <343750>;
+			led-max-microamp = <55000>;
+		};
+	};
+
+	/* Bit-banged I2C on GPIO143 and GPIO144 also called "SUBPMU I2C" */
+	i2c-gpio-0 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpio4 16 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpio4 15 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c_gpio_0_default>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* TODO: this should also be used by the SM5103 Camera power management unit */
+	};
+
+	/* Bit-banged I2C on GPIO151 and GPIO152 also called "COMP I2C" */
+	i2c-gpio-1 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpio4 24 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpio4 23 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c_gpio_1_default>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		magnetometer@c {
+			compatible = "alps,hscdtd008a";
+			reg = <0x0c>;
+			clock-frequency = <400000>;
+
+			avdd-supply = <&ab8500_ldo_aux1_reg>; // 3V
+			dvdd-supply = <&ab8500_ldo_aux8_reg>; // 1.8V
+		};
+	};
+
+	spi-gpio-0 {
+		compatible = "spi-gpio";
+		/* Clock on GPIO220, pin SCL */
+		sck-gpios = <&gpio6 28 GPIO_ACTIVE_HIGH>;
+		/* MOSI on GPIO224, pin SDI "slave data in" */
+		mosi-gpios = <&gpio7 0 GPIO_ACTIVE_HIGH>;
+		/* MISO on GPIO225, pin SDO "slave data out" */
+		miso-gpios = <&gpio7 1 GPIO_ACTIVE_HIGH>;
+		/* Chip select on GPIO201 */
+		cs-gpios = <&gpio6 9 GPIO_ACTIVE_LOW>;
+		num-chipselects = <1>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&spi_gpio_0_default>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		panel@0 {
+			compatible = "samsung,s6d27a1";
+			spi-max-frequency = <1200000>;
+			/* TYPE 3: inverse clock polarity and phase */
+			spi-cpha;
+			spi-cpol;
+
+			reg = <0>;
+			vci-supply = <&lcd_3v0_reg>;
+			vccio-supply = <&ab8500_ldo_aux6_reg>;
+
+			/* Reset on GPIO139 */
+			reset-gpios = <&gpio4 11 GPIO_ACTIVE_LOW>;
+			/* LCD_VGH/LCD_DETECT, ESD IRQ on GPIO93 */
+			interrupt-parent = <&gpio2>;
+			interrupts = <29 IRQ_TYPE_EDGE_RISING>;
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&panel_default_mode>;
+			backlight = <&ktd253>;
+
+			port {
+				panel_in: endpoint {
+					remote-endpoint = <&display_out>;
+				};
+			};
+		};
+	};
+
+	soc {
+		/* External Micro SD slot */
+		mmc@80126000 {
+			arm,primecell-periphid = <0x10480180>;
+			max-frequency = <100000000>;
+			bus-width = <4>;
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			st,sig-pin-fbclk;
+			full-pwr-cycle;
+			/* MMC is powered by AUX3 1.2V .. 2.91V */
+			vmmc-supply = <&ab8500_ldo_aux3_reg>;
+			/* 2.9 V level translator is using AUX3 at 2.9 V as well */
+			vqmmc-supply = <&sd_level_translator>;
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&mc0_a_2_default>;
+			pinctrl-1 = <&mc0_a_2_sleep>;
+			cd-gpios  = <&gpio6 25 GPIO_ACTIVE_LOW>; // GPIO217
+			status = "okay";
+		};
+
+		/* WLAN SDIO channel */
+		mmc@80118000 {
+			arm,primecell-periphid = <0x10480180>;
+			max-frequency = <50000000>;
+			bus-width = <4>;
+			non-removable;
+			cap-sd-highspeed;
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&mc1_a_2_default>;
+			pinctrl-1 = <&mc1_a_2_sleep>;
+			/*
+			 * GPIO-controlled voltage enablement: this drives
+			 * the WL_REG_ON line high when we use this device.
+			 * Represented as regulator to fill OCR mask.
+			 */
+			vmmc-supply = <&wl_reg>;
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "okay";
+
+			wifi@1 {
+				compatible = "brcm,bcm4334-fmac", "brcm,bcm4329-fmac";
+				reg = <1>;
+				/* GPIO216 WL_HOST_WAKE */
+				interrupt-parent = <&gpio6>;
+				interrupts = <24 IRQ_TYPE_EDGE_FALLING>;
+				interrupt-names = "host-wake";
+				pinctrl-names = "default";
+				pinctrl-0 = <&wlan_default_mode>;
+			};
+		};
+
+		/* eMMC */
+		mmc@80005000 {
+			arm,primecell-periphid = <0x10480180>;
+			max-frequency = <100000000>;
+			bus-width = <8>;
+			non-removable;
+			cap-mmc-highspeed;
+			mmc-ddr-1_8v;
+			no-sdio;
+			no-sd;
+			vmmc-supply = <&ldo_3v3_reg>;
+			pinctrl-names = "default", "sleep";
+			/*
+			 * GPIO130 will be set to input no pull-up resulting in a resistor
+			 * pulling the reset high and taking the memory out of reset.
+			 */
+			pinctrl-0 = <&mc2_a_1_default>;
+			pinctrl-1 = <&mc2_a_1_sleep>;
+			status = "okay";
+		};
+
+		/* GBF (Bluetooth) UART */
+		uart@80120000 {
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&u0_a_1_default>;
+			pinctrl-1 = <&u0_a_1_sleep>;
+			status = "okay";
+
+			bluetooth {
+				/* BCM4334B0 actually */
+				compatible = "brcm,bcm4330-bt";
+				/* GPIO222 rail BT_VREG_EN to BT_REG_ON */
+				shutdown-gpios = <&gpio6 30 GPIO_ACTIVE_HIGH>;
+				/* BT_WAKE on GPIO199 */
+				device-wakeup-gpios = <&gpio6 7 GPIO_ACTIVE_HIGH>;
+				/* BT_HOST_WAKE on GPIO97 */
+				/* FIXME: convert to interrupt */
+				host-wakeup-gpios = <&gpio3 1 GPIO_ACTIVE_HIGH>;
+				/* BT_RST_N on GPIO209 */
+				reset-gpios = <&gpio6 17 GPIO_ACTIVE_LOW>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&bluetooth_default_mode>;
+			};
+		};
+
+		/* GPS UART */
+		uart@80121000 {
+			status = "okay";
+			pinctrl-names = "default", "sleep";
+			/* CTS/RTS is not used, CTS is repurposed as GPIO */
+			pinctrl-0 = <&u1rxtx_a_1_default>;
+			pinctrl-1 = <&u1rxtx_a_1_sleep>;
+			/* FIXME: add a device for the GPS here */
+		};
+
+		/* Debugging console UART connected to AB8505 */
+		uart@80007000 {
+			status = "okay";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&u2rxtx_c_1_default>;
+			pinctrl-1 = <&u2rxtx_c_1_sleep>;
+		};
+
+		prcmu@80157000 {
+			ab8505 {
+				phy {
+					pinctrl-names = "default", "sleep";
+					pinctrl-0 = <&usb_a_1_default>;
+					pinctrl-1 = <&usb_a_1_sleep>;
+				};
+
+				ab8500_fg {
+					line-impedance-micro-ohms = <36000>;
+				};
+
+				/* This is mostly identical to the Codina v0.4 regulators */
+				regulator {
+					ab8500_ldo_aux1 {
+						regulator-name = "v-sensors-vdd";
+						regulator-min-microvolt = <3000000>;
+						regulator-max-microvolt = <3300000>;
+					};
+
+					ab8500_ldo_aux2 {
+						regulator-name = "v-aux2";
+						regulator-min-microvolt = <3300000>;
+						regulator-max-microvolt = <3300000>;
+					};
+
+					ab8500_ldo_aux3 {
+						regulator-name = "v-mmc-sd";
+					};
+
+					ab8500_ldo_aux4 {
+						regulator-name = "v-aux4";
+						/*
+						 * Providing some span here makes the touchkey
+						 * LEDs actually dimmable.
+						 */
+						regulator-min-microvolt = <1100000>;
+						regulator-max-microvolt = <3300000>;
+					};
+
+					ab8500_ldo_aux5 {
+						regulator-name = "v-aux5";
+						regulator-min-microvolt = <1800000>;
+						regulator-max-microvolt = <1800000>;
+					};
+
+					ab8500_ldo_aux6 {
+						/* 1.8 V to the display */
+						regulator-name = "v-aux6";
+						regulator-min-microvolt = <1800000>;
+						regulator-max-microvolt = <1800000>;
+					};
+
+					ab8500_ldo_aux8 {
+						regulator-name = "v-sensors-vio";
+					};
+				};
+			};
+		};
+
+		/* I2C0 also known as "AGC I2C" */
+		i2c@80004000 {
+			status = "okay";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&i2c0_a_1_default>;
+			pinctrl-1 = <&i2c0_a_1_sleep>;
+
+			proximity@39 {
+				/* Codina has the Amstaos TMD2672 */
+				compatible = "amstaos,tmd2672";
+				clock-frequency = <400000>;
+				reg = <0x39>;
+
+				/* IRQ on GPIO146 "PS_INT" */
+				interrupt-parent = <&gpio4>;
+				interrupts = <18 IRQ_TYPE_EDGE_FALLING>;
+				vdd-supply = <&ab8500_ldo_aux1_reg>;
+				vddio-supply = <&ab8500_ldo_aux8_reg>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&tmd2672_codina_default>;
+			};
+		};
+
+		/* I2C2 on GPIO10 and GPIO11 also called "SENSORS I2C" */
+		i2c@80128000 {
+			status = "okay";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&i2c2_b_2_default>;
+			pinctrl-1 = <&i2c2_b_2_sleep>;
+
+			/* Bosch BMA254 accelerometer */
+			accelerometer@18 {
+				compatible = "bosch,bma254";
+				reg = <0x18>;
+				mount-matrix = "0", "1", "0",
+					       "-1", "0", "0",
+					       "0", "0", "1";
+				vddio-supply = <&ab8500_ldo_aux8_reg>; // 1.8V
+				vdd-supply = <&ab8500_ldo_aux1_reg>; // 3V
+			};
+		};
+
+		/* I2C3 */
+		i2c@80110000 {
+			status = "okay";
+
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&i2c3_c_2_default>;
+			pinctrl-1 = <&i2c3_c_2_sleep>;
+
+			/* TODO: write bindings and driver for this touchscreen */
+
+			/* Zinitix BT404 ISP part */
+			isp@50 {
+				compatible = "zinitix,bt404-isp";
+				reg = <0x50>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&tsp_default>;
+			};
+
+			/* Zinitix BT404 touchscreen, also has the touchkeys for menu and back */
+			touchscreen@20 {
+				compatible = "zinitix,bt404";
+				reg = <0x20>;
+				/* GPIO218 (TSP_INT_1V8) */
+				interrupt-parent = <&gpio6>;
+				interrupts = <26 IRQ_TYPE_EDGE_FALLING>;
+				vcca-supply = <&ab8500_ldo_aux2_reg>; // 3.3V
+				vdd-supply = <&ab8500_ldo_aux5_reg>; // 1.8V
+				zinitix,mode = <2>;
+				touchscreen-size-x = <480>;
+				touchscreen-size-y = <800>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&tsp_default>;
+			};
+		};
+
+		mcde@a0350000 {
+			status = "okay";
+			pinctrl-names = "default";
+			pinctrl-0 = <&dpi_default_mode>;
+
+			port {
+				display_out: endpoint {
+					remote-endpoint = <&panel_in>;
+				};
+			};
+		};
+	};
+};
+
+&pinctrl {
+	/*
+	 * This extends the MC0_A_2 default config to include
+	 * the card detect GPIO217 line.
+	 */
+	sdi0 {
+		mc0_a_2_default {
+			default_cfg4 {
+				pins = "GPIO217_AH12"; /* card detect */
+				ste,config = <&gpio_in_pd>;
+			};
+		};
+	};
+	sdi2 {
+		/*
+		 * GPIO130 should be set in GPIO mode and
+		 * pulled down. (Not connected.)
+		 */
+		mc2_a_1_default {
+			default_cfg2 {
+				pins = "GPIO130_C8"; /* FBCLK */
+				ste,config = <&gpio_in_pd>;
+			};
+		};
+	};
+	/* GPIO that enables the 2.9V SD card level translator */
+	sd-level-translator {
+		sd_level_translator_default: sd_level_translator_default {
+			/* level shifter on GPIO87 */
+			codina_cfg1 {
+				pins = "GPIO87_B3";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+	/* GPIO that enables the LDO regulator for the eMMC */
+	emmc-ldo {
+		emmc_ldo_en_default_mode: emmc_ldo_default {
+			/* LDO enable on GPIO223 */
+			codina_cfg1 {
+				pins = "GPIO223_AH9";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+	/* GPIOs for panel control */
+	panel {
+		panel_default_mode: panel_default {
+			codina_cfg1 {
+				/* Reset line */
+				pins = "GPIO139_C9";
+				ste,config = <&gpio_out_lo>;
+			};
+			codina_cfg2 {
+				/* ESD IRQ line "LCD detect" */
+				pins = "GPIO93_B7";
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	/* GPIO that enables the LDO regulator for the LCD display */
+	lcd-ldo {
+		lcd_pwr_en_default_mode: lcd_pwr_en_default {
+			/* LCD_PWR_EN on GPIO219 */
+			codina_cfg1 {
+				pins = "GPIO219_AG10";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+	/* GPIO that enables the WLAN internal LDO regulators */
+	wlan-ldo {
+		wlan_ldo_en_default: wlan_ldo_default {
+			/* GPIO215 named WLAN_RST_N */
+			codina_cfg1 {
+				pins = "GPIO215_AH13";
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+	/* Backlight GPIO */
+	backlight {
+		ktd253_backlight_default_mode: backlight_default {
+			skomer_cfg1 {
+				pins = "GPIO69_E2"; /* LCD_BL_CTRL */
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+	/* Flash and torch */
+	flash {
+		gpio_flash_default_mode: flash_default {
+			codina_cfg1 {
+				pins = "GPIO140_B11", "GPIO141_C12";
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+	/* GPIO keys */
+	gpio-keys {
+		gpio_keys_default_mode: gpio_keys_default {
+			skomer_cfg1 {
+				pins = "GPIO67_G2", /* VOL UP */
+				       "GPIO91_B6", /* HOME */
+				       "GPIO92_D6"; /* VOL DOWN */
+				ste,config = <&gpio_in_pu>;
+			};
+		};
+	};
+	/* Interrupt line for the Zinitix BT404 touchscreen */
+	tsp {
+		tsp_default: tsp_default {
+			codina_cfg1 {
+				pins = "GPIO218_AH11";	/* TSP_INT_1V8 */
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	/* Interrupt line for light/proximity sensor TMD2672 */
+	tmd2672 {
+		tmd2672_codina_default: tmd2672_codina {
+			codina_cfg1 {
+				pins = "GPIO146_D13";
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	/* GPIO-based I2C bus for subpmu */
+	i2c-gpio-0 {
+		i2c_gpio_0_default: i2c_gpio_0 {
+			codina_cfg1 {
+				pins = "GPIO143_D12", "GPIO144_B13";
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	/* GPIO-based I2C bus for the NFC */
+	i2c-gpio-1 {
+		i2c_gpio_1_default: i2c_gpio_1 {
+			codina_cfg1 {
+				pins = "GPIO151_D17", "GPIO152_D16";
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	/* GPIO-based SPI bus for the display */
+	spi-gpio-0 {
+		spi_gpio_0_default: spi_gpio_0_d {
+			codina_cfg1 {
+				pins = "GPIO220_AH10", "GPIO201_AF24", "GPIO224_AG9";
+				ste,config = <&gpio_out_hi>;
+			};
+			codina_cfg2 {
+				pins = "GPIO225_AG8";
+				/* Needs pull down, no pull down resistor on board */
+				ste,config = <&gpio_in_pd>;
+			};
+		};
+		spi_gpio_0_sleep: spi_gpio_0_s {
+			codina_cfg1 {
+				pins = "GPIO220_AH10", "GPIO201_AF24",
+				       "GPIO224_AG9", "GPIO225_AG8";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+	wlan {
+		wlan_default_mode: wlan_default {
+			/* GPIO216 for WL_HOST_WAKE */
+			codina_cfg2 {
+				pins = "GPIO216_AG12";
+				ste,config = <&gpio_in_pd>;
+			};
+		};
+	};
+	bluetooth {
+		bluetooth_default_mode: bluetooth_default {
+			/* GPIO199 BT_WAKE and GPIO222 BT_VREG_ON */
+			codina_cfg1 {
+				pins = "GPIO199_AH23", "GPIO222_AJ9";
+				ste,config = <&gpio_out_lo>;
+			};
+			/* GPIO97 BT_HOST_WAKE */
+			codina_cfg2 {
+				pins = "GPIO97_D9";
+				ste,config = <&gpio_in_nopull>;
+			};
+			/* GPIO209 BT_RST_N */
+			codina_cfg3 {
+				pins = "GPIO209_AG15";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+	vibrator {
+		vibrator_default: vibrator_default {
+			codina_cfg1 {
+				pins = "GPIO195_AG28";	/* MOT_EN */
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+	mcde {
+		dpi_default_mode: dpi_default {
+			default_mux1 {
+				/* Mux in all the data lines */
+				function = "lcd";
+				groups =
+					/* Data lines D0-D7 GPIO70..GPIO77 */
+					"lcd_d0_d7_a_1",
+					/* Data lines D8-D11 GPIO78..GPIO81 */
+					"lcd_d8_d11_a_1",
+					/* Data lines D12-D15 GPIO82..GPIO85 */
+					"lcd_d12_d15_a_1",
+					/* Data lines D16-D23 GPIO161..GPIO168 */
+					"lcd_d16_d23_b_1";
+			};
+			default_mux2 {
+				function = "lcda";
+				/* Clock line on GPIO150, DE, VSO, HSO on GPIO169..GPIO171 */
+				groups = "lcdaclk_b_1", "lcda_b_1";
+			};
+			/* Input, no pull-up is the default state for pins used for an alt function */
+			default_cfg1 {
+				pins = "GPIO150_C14", "GPIO169_D22", "GPIO170_C23", "GPIO171_D23";
+				ste,config = <&in_nopull>;
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/ste-ux500-samsung-codina.dts b/arch/arm/boot/dts/ste-ux500-samsung-codina.dts
index fbd60065542d..b88f0c07873d 100644
--- a/arch/arm/boot/dts/ste-ux500-samsung-codina.dts
+++ b/arch/arm/boot/dts/ste-ux500-samsung-codina.dts
@@ -9,9 +9,13 @@
  * the boot loader.
  *
  * The Samsung tree further talks about GT-I8160P and GT-I8160chn (China).
- * The GT-I8160 plain is knonw as the "europe" variant.
- * The GT-I8160P appears to not use the ST Microelectronics accelerometer.
+ * The GT-I8160 plain is known as the "europe" variant.
+ * The GT-I8160P is the CDMA version and it appears to not use the ST
+ * Microelectronics accelerometer and reportedly has NFC mounted.
  * The GT-I8160chn appears to be the same as the europe variant.
+ *
+ * There is also the Codina-TMO, Samsung SGH-T599, which has its own device
+ * tree.
  */
 
 /dts-v1/;
@@ -47,6 +51,32 @@
 		compatible = "samsung,eb425161lu";
 	};
 
+	thermal-zones {
+		battery-thermal {
+			/* This zone will be polled by the battery temperature code */
+			polling-delay = <0>;
+			polling-delay-passive = <0>;
+			thermal-sensors = <&bat_therm>;
+
+			trips {
+				battery-crit-hi {
+					temperature = <70000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+	};
+
+	bat_therm: thermistor {
+		compatible = "samsung,1404-001221";
+		io-channels = <&gpadc 0x02>; /* BatTemp */
+		pullup-uv = <1800000>;
+		pullup-ohm = <230000>;
+		pulldown-ohm = <0>;
+		#thermal-sensor-cells = <0>;
+	};
+
 	/* TI TXS0206 level translator for 2.9 V */
 	sd_level_translator: regulator-gpio {
 		compatible = "regulator-fixed";
@@ -285,7 +315,22 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		/* TODO: add the NFC chip here */
+		nfc@2b {
+			/* NXP NFC circuit PN544 C1 marked NXP 44501  */
+			compatible = "nxp,pn544-i2c";
+			/* IF0, IF1 high, gives I2C address 0x2B */
+			reg = <0x2b>;
+			clock-frequency = <400000>;
+			/* NFC IRQ on GPIO32 */
+			interrupt-parent = <&gpio1>;
+			interrupts = <0 IRQ_TYPE_EDGE_FALLING>;
+			/* GPIO 31 */
+			firmware-gpios = <&gpio0 31 GPIO_ACTIVE_HIGH>;
+			/* GPIO88 */
+			enable-gpios = <&gpio2 24 GPIO_ACTIVE_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pn544_codina_default>;
+		};
 	};
 
 	spi-gpio-0 {
@@ -443,10 +488,20 @@
 		uart@80121000 {
 			status = "okay";
 			pinctrl-names = "default", "sleep";
-			/* CTS/RTS is not used, CTS is repurposed as GPIO */
-			pinctrl-0 = <&u1rxtx_a_1_default>;
-			pinctrl-1 = <&u1rxtx_a_1_sleep>;
-			/* FIXME: add a device for the GPS here */
+			pinctrl-0 = <&u1rxtx_a_1_default &u1ctsrts_a_1_default>;
+			pinctrl-1 = <&u1rxtx_a_1_sleep &u1ctsrts_a_1_sleep>;
+
+			gnss {
+				compatible = "brcm,bcm4751";
+				/* GPS_RSTN on GPIO21 */
+				reset-gpios = <&gpio0 21 GPIO_ACTIVE_LOW>;
+				/* GPS_ON_OFF on GPIO86 */
+				enable-gpios = <&gpio2 22 GPIO_ACTIVE_HIGH>;
+				/* GPS_1V8 (VSMPS2) */
+				vddio-supply = <&db8500_vsmps2_reg>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&bcm4751_codina_default>;
+			};
 		};
 
 		/* Debugging console UART connected to TSU6111RSVR (FSA880) */
@@ -459,13 +514,17 @@
 
 		prcmu@80157000 {
 			ab8500 {
-				ab8500_usb {
+				phy {
 					pinctrl-names = "default", "sleep";
 					pinctrl-0 = <&usb_a_1_default>;
 					pinctrl-1 = <&usb_a_1_sleep>;
 				};
 
-				ab8500-regulators {
+				ab8500_fg {
+					line-impedance-micro-ohms = <36000>;
+				};
+
+				regulator {
 					ab8500_ldo_aux1 {
 						/* Used for VDD for sensors */
 						regulator-name = "V-SENSORS-VDD";
@@ -497,10 +556,9 @@
 			pinctrl-0 = <&i2c0_a_1_default>;
 			pinctrl-1 = <&i2c0_a_1_sleep>;
 
-			/* TODO: write bindings and driver for this proximity sensor */
 			proximity@39 {
-				/* Codina has the Mouser TMD2672 */
-				compatible = "mouser,tmd2672";
+				/* Codina has the Amstaos TMD2672 */
+				compatible = "amstaos,tmd2672";
 				clock-frequency = <400000>;
 				reg = <0x39>;
 
@@ -548,8 +606,8 @@
 				reg = <0x19>;
 				vdd-supply = <&ab8500_ldo_aux1_reg>; // 3V
 				vddio-supply = <&ab8500_ldo_aux2_reg>; // 1.8V
-				mount-matrix = "0", "-1", "0",
-					       "1", "0", "0",
+				mount-matrix = "0", "1", "0",
+					       "-1", "0", "0",
 					       "0", "0", "1";
 			};
 		};
@@ -829,6 +887,34 @@
 			};
 		};
 	};
+	nfc {
+		pn544_codina_default: pn544_codina {
+			/* Interrupt line */
+			codina_cfg1 {
+				pins = "GPIO32_V2";
+				ste,config = <&gpio_in_nopull>;
+			};
+			/* Enable and firmware GPIOs */
+			codina_cfg2 {
+				pins = "GPIO31_V3", "GPIO88_C4";
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+	bcm4751 {
+		bcm4751_codina_default: bcm4751_codina {
+			/* Reset line, start out asserted */
+			codina_cfg1 {
+				pins = "GPIO21_AB3";
+				ste,config = <&gpio_out_lo>;
+			};
+			/* GPS_ON_OFF, start out deasserted (off) */
+			codina_cfg2 {
+				pins = "GPIO86_C6";
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
 	vibrator {
 		vibrator_default: vibrator_default {
 			codina_cfg1 {
diff --git a/arch/arm/boot/dts/ste-ux500-samsung-gavini.dts b/arch/arm/boot/dts/ste-ux500-samsung-gavini.dts
index 47bbf5ab267f..7231bc745200 100644
--- a/arch/arm/boot/dts/ste-ux500-samsung-gavini.dts
+++ b/arch/arm/boot/dts/ste-ux500-samsung-gavini.dts
@@ -24,6 +24,32 @@
 		compatible = "samsung,eb585157lu";
 	};
 
+	thermal-zones {
+		battery-thermal {
+			/* This zone will be polled by the battery temperature code */
+			polling-delay = <0>;
+			polling-delay-passive = <0>;
+			thermal-sensors = <&bat_therm>;
+
+			trips {
+				battery-crit-hi {
+					temperature = <70000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+	};
+
+	bat_therm: thermistor {
+		compatible = "samsung,1404-001221";
+		io-channels = <&gpadc 0x02>; /* BatTemp */
+		pullup-uv = <1800000>;
+		pullup-ohm = <230000>;
+		pulldown-ohm = <0>;
+		#thermal-sensor-cells = <0>;
+	};
+
 	/* TI TXS0206 level translator for 2.9 V */
 	sd_level_translator: regulator-gpio {
 		compatible = "regulator-fixed";
@@ -232,19 +258,18 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		/* TODO: Memsic MMC328 magnetometer */
-		magnetometer@30 {
-			compatible = "memsic,mmc328";
-			reg = <0x30>;
-			/* TODO: if you have the schematic, check if both voltages come from AUX2 */
-			/* VDA 1.8 V */
-			vda-supply = <&ab8500_ldo_aux2_reg>;
-			/* VDD 1.8V */
-			vdd-supply = <&ab8500_ldo_aux2_reg>;
-			/* GPIO204 */
+		/* Yamaha YAS530 magnetometer */
+		magnetometer@2e {
+			compatible = "yamaha,yas530";
+			reg = <0x2e>;
+			/* VDD 3V */
+			vdd-supply = <&ab8500_ldo_aux1_reg>;
+			/* IOVDD 1.8V */
+			iovdd-supply = <&ab8500_ldo_aux2_reg>;
+			/* GPIO204 COMPASS_RST_N */
 			reset-gpios = <&gpio6 12 GPIO_ACTIVE_LOW>;
 			pinctrl-names = "default";
-			pinctrl-0 = <&mmc328_default>;
+			pinctrl-0 = <&yas530_default>;
 		};
 		/* TODO: this should also be used by the NCP6914 Camera power management unit */
 	};
@@ -433,13 +458,17 @@
 
 		prcmu@80157000 {
 			ab8500 {
-				ab8500_usb {
+				phy {
 					pinctrl-names = "default", "sleep";
 					pinctrl-0 = <&usb_a_1_default>;
 					pinctrl-1 = <&usb_a_1_sleep>;
 				};
 
-				ab8500-regulators {
+				ab8500_fg {
+					line-impedance-micro-ohms = <43000>;
+				};
+
+				regulator {
 					ab8500_ldo_aux1 {
 						/* Used for VDD for sensors */
 						regulator-name = "V-SENSORS-VDD";
@@ -506,8 +535,8 @@
 					accelerometer@18 {
 						compatible = "bosch,bma222e";
 						reg = <0x18>;
-						mount-matrix = "0", "1", "0",
-							       "-1", "0", "0",
+						mount-matrix = "0", "-1", "0",
+							       "1", "0", "0",
 							       "0", "0", "1";
 						vddio-supply = <&ab8500_ldo_aux2_reg>; // 1.8V
 						vdd-supply = <&ab8500_ldo_aux1_reg>; // 3V
@@ -645,6 +674,15 @@
 			};
 		};
 	};
+	/* Reset line for the Yamaha YAS530 magnetometer */
+	yas530 {
+		yas530_default: yas530_janice {
+			janice_cfg1 {
+				pins = "GPIO204_AF23";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
 	/* Flash and torch */
 	flash {
 		gpio_flash_default_mode: flash_default {
@@ -747,15 +785,6 @@
 			};
 		};
 	};
-	/* Reset line for the Memsic MMC328 magnetometer */
-	mmc328 {
-		mmc328_default: mmc328_gavini {
-			gavini_cfg1 {
-				pins = "GPIO204_AF23";
-				ste,config = <&gpio_out_hi>;
-			};
-		};
-	};
 	/* Interrupt line for Invensense MPU3050 gyroscope */
 	mpu3050 {
 		mpu3050_default: mpu3050 {
diff --git a/arch/arm/boot/dts/ste-ux500-samsung-golden.dts b/arch/arm/boot/dts/ste-ux500-samsung-golden.dts
index fc4c5166d85b..9604695edf53 100644
--- a/arch/arm/boot/dts/ste-ux500-samsung-golden.dts
+++ b/arch/arm/boot/dts/ste-ux500-samsung-golden.dts
@@ -29,6 +29,32 @@
 		compatible = "samsung,eb-l1m7flu";
 	};
 
+	thermal-zones {
+		battery-thermal {
+			/* This zone will be polled by the battery temperature code */
+			polling-delay = <0>;
+			polling-delay-passive = <0>;
+			thermal-sensors = <&bat_therm>;
+
+			trips {
+				battery-crit-hi {
+					temperature = <70000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+	};
+
+	bat_therm: thermistor {
+		compatible = "samsung,1404-001221";
+		io-channels = <&gpadc 0x02>; /* BatTemp */
+		pullup-uv = <1800000>;
+		pullup-ohm = <230000>;
+		pulldown-ohm = <0>;
+		#thermal-sensor-cells = <0>;
+	};
+
 	i2c-gpio-0 {
 		compatible = "i2c-gpio";
 		sda-gpios = <&gpio2 14 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
@@ -280,13 +306,17 @@
 
 		prcmu@80157000 {
 			ab8505 {
-				ab8500_usb {
+				phy {
 					pinctrl-names = "default", "sleep";
 					pinctrl-0 = <&usb_a_1_default>;
 					pinctrl-1 = <&usb_a_1_sleep>;
 				};
 
-				ab8505-regulators {
+				ab8500_fg {
+					line-impedance-micro-ohms = <36000>;
+				};
+
+				regulator {
 					ab8500_ldo_aux1 {
 						regulator-name = "sensor_3v";
 						regulator-min-microvolt = <3000000>;
diff --git a/arch/arm/boot/dts/ste-ux500-samsung-janice.dts b/arch/arm/boot/dts/ste-ux500-samsung-janice.dts
index 5ddcbc1a855d..69387e8754a9 100644
--- a/arch/arm/boot/dts/ste-ux500-samsung-janice.dts
+++ b/arch/arm/boot/dts/ste-ux500-samsung-janice.dts
@@ -24,6 +24,32 @@
 		compatible = "samsung,eb535151vu";
 	};
 
+	thermal-zones {
+		battery-thermal {
+			/* This zone will be polled by the battery temperature code */
+			polling-delay = <0>;
+			polling-delay-passive = <0>;
+			thermal-sensors = <&bat_therm>;
+
+			trips {
+				battery-crit-hi {
+					temperature = <70000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+	};
+
+	bat_therm: thermistor {
+		compatible = "samsung,1404-001221";
+		io-channels = <&gpadc 0x02>; /* BatTemp */
+		pullup-uv = <1800000>;
+		pullup-ohm = <230000>;
+		pulldown-ohm = <0>;
+		#thermal-sensor-cells = <0>;
+	};
+
 	/* External LDO for eMMC LDO VMEM_3V3 controlled by GPIO6 */
 	ldo_3v3_reg: regulator-gpio-ldo-3v3 {
 		compatible = "regulator-fixed";
@@ -467,7 +493,26 @@
 			/* CTS/RTS is not used, CTS is repurposed as GPIO */
 			pinctrl-0 = <&u1rxtx_a_1_default>;
 			pinctrl-1 = <&u1rxtx_a_1_sleep>;
-			/* FIXME: add a device for the GPS here */
+
+			gnss {
+				/*
+				 * The Low Noise Amplifier (LNA) power and enablement is controlled
+				 * autonomously by the GSD4t.
+				 * Janice has a SiRFstarIV-based GSD4t
+				 * Golden has a SiRFstarV 5t-based CSRG05TA03-ICJE-R.
+				 */
+				compatible = "csr,gsd4t";
+				/* GPS_RSTN on GPIO21 */
+				reset-gpios = <&gpio0 21 GPIO_ACTIVE_LOW>;
+				/* GPS_ON_OFF on GPIO96 */
+				sirf,onoff-gpios = <&gpio3 0 GPIO_ACTIVE_HIGH>;
+				/* GPS_1V8 (VSMPS2) */
+				vcc-supply = <&db8500_vsmps2_reg>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&gsd4t_janice_default>;
+				/* According to /etc/sirfgps.conf */
+				current-speed = <460800>;
+			};
 		};
 
 		/* Debugging console UART connected to TSU6111RSVR (FSA880) */
@@ -480,13 +525,17 @@
 
 		prcmu@80157000 {
 			ab8500 {
-				ab8500_usb {
+				phy {
 					pinctrl-names = "default", "sleep";
 					pinctrl-0 = <&usb_a_1_default>;
 					pinctrl-1 = <&usb_a_1_sleep>;
 				};
 
-				ab8500-regulators {
+				ab8500_fg {
+					line-impedance-micro-ohms = <15000>;
+				};
+
+				regulator {
 					ab8500_ldo_aux1 {
 						/* Used for VDD for sensors */
 						regulator-name = "V-SENSORS-VDD";
@@ -592,9 +641,9 @@
 					accelerometer@8 {
 						compatible = "bosch,bma222";
 						reg = <0x08>;
-						mount-matrix = "0", "1", "0",
-							       "-1", "0", "0",
-							       "0", "0", "-1";
+						mount-matrix = "0", "-1", "0",
+							       "1", "0", "0",
+							       "0", "0", "1";
 						vddio-supply = <&ab8500_ldo_aux2_reg>; // 1.8V
 						vdd-supply = <&ab8500_ldo_aux1_reg>; // 3V
 					};
@@ -923,4 +972,23 @@
 			};
 		};
 	};
+	gsd4t {
+		gsd4t_janice_default: gsd4t_janice {
+			/* Reset line, start out asserted */
+			janice_cfg1 {
+				pins = "GPIO21_AB3";
+				ste,config = <&gpio_out_lo>;
+			};
+			/* GPS_ON_OFF, start out deasserted (off) */
+			janice_cfg2 {
+				pins = "GPIO96_D8";
+				ste,config = <&gpio_out_lo>;
+			};
+			/* Unused power enablement line, used in R0.0 and R0.1 boards */
+			janice_cfg3 {
+				pins = "GPIO86_C6";
+				ste,config = <&gpio_in_pd>;
+			};
+		};
+	};
 };
diff --git a/arch/arm/boot/dts/ste-ux500-samsung-kyle.dts b/arch/arm/boot/dts/ste-ux500-samsung-kyle.dts
index 9ec3f85b1a18..167846df3104 100644
--- a/arch/arm/boot/dts/ste-ux500-samsung-kyle.dts
+++ b/arch/arm/boot/dts/ste-ux500-samsung-kyle.dts
@@ -28,6 +28,32 @@
 		compatible = "samsung,eb425161la";
 	};
 
+	thermal-zones {
+		battery-thermal {
+			/* This zone will be polled by the battery temperature code */
+			polling-delay = <0>;
+			polling-delay-passive = <0>;
+			thermal-sensors = <&bat_therm>;
+
+			trips {
+				battery-crit-hi {
+					temperature = <70000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+	};
+
+	bat_therm: thermistor {
+		compatible = "samsung,1404-001221";
+		io-channels = <&gpadc 0x02>; /* BatTemp */
+		pullup-uv = <1800000>;
+		pullup-ohm = <230000>;
+		pulldown-ohm = <0>;
+		#thermal-sensor-cells = <0>;
+	};
+
 	/* TI TXS0206 level translator for 2.9 V */
 	sd_level_translator: regulator-gpio {
 		compatible = "regulator-fixed";
@@ -301,13 +327,17 @@
 
 		prcmu@80157000 {
 			ab8505 {
-				ab8500_usb {
+				phy {
 					pinctrl-names = "default", "sleep";
 					pinctrl-0 = <&usb_a_1_default>;
 					pinctrl-1 = <&usb_a_1_sleep>;
 				};
 
-				ab8505-regulators {
+				ab8500_fg {
+					line-impedance-micro-ohms = <36000>;
+				};
+
+				regulator {
 					ab8500_ldo_aux1 {
 						/* Used for VDD for sensors */
 						regulator-name = "AUX1";
diff --git a/arch/arm/boot/dts/ste-ux500-samsung-skomer.dts b/arch/arm/boot/dts/ste-ux500-samsung-skomer.dts
index 580ca497f312..93e5f5ed888d 100644
--- a/arch/arm/boot/dts/ste-ux500-samsung-skomer.dts
+++ b/arch/arm/boot/dts/ste-ux500-samsung-skomer.dts
@@ -24,6 +24,32 @@
 		compatible = "samsung,eb485159lu";
 	};
 
+	thermal-zones {
+		battery-thermal {
+			/* This zone will be polled by the battery temperature code */
+			polling-delay = <0>;
+			polling-delay-passive = <0>;
+			thermal-sensors = <&bat_therm>;
+
+			trips {
+				battery-crit-hi {
+					temperature = <70000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+	};
+
+	bat_therm: thermistor {
+		compatible = "samsung,1404-001221";
+		io-channels = <&gpadc 0x02>; /* BatTemp */
+		pullup-uv = <1800000>;
+		pullup-ohm = <230000>;
+		pulldown-ohm = <0>;
+		#thermal-sensor-cells = <0>;
+	};
+
 	/* TI TXS0206 level translator for 2.9 V */
 	sd_level_translator: regulator-gpio {
 		compatible = "regulator-fixed";
@@ -185,10 +211,6 @@
 			cap-sd-highspeed;
 			cap-mmc-highspeed;
 			/* All direction control is used */
-			st,sig-dir-cmd;
-			st,sig-dir-dat0;
-			st,sig-dir-dat2;
-			st,sig-dir-dat31;
 			st,sig-pin-fbclk;
 			full-pwr-cycle;
 			vmmc-supply = <&ab8500_ldo_aux3_reg>;
@@ -267,12 +289,27 @@
 			};
 		};
 
-		/* GPF UART */
+		/* GPS UART */
 		uart@80121000 {
 			status = "okay";
 			pinctrl-names = "default", "sleep";
 			pinctrl-0 = <&u1rxtx_a_1_default &u1ctsrts_a_1_default>;
 			pinctrl-1 = <&u1rxtx_a_1_sleep &u1ctsrts_a_1_sleep>;
+
+			gnss {
+				/* The CSRG05TA03-ICJE-R is a SirfStarV 5t chip */
+				compatible = "csr,csrg05ta03-icje-r";
+				/* GPS_RSTN on GPIO209 */
+				reset-gpios = <&gpio6 17 GPIO_ACTIVE_LOW>;
+				/* GPS_ON_OFF on GPIO86 */
+				sirf,onoff-gpios = <&gpio2 22 GPIO_ACTIVE_HIGH>;
+				/* GPS_1V8 (VSMPS2) */
+				vcc-supply = <&db8500_vsmps2_reg>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&g05ta03_skomer_default>;
+				/* According to /etc/sirfgps.conf */
+				current-speed = <460800>;
+			};
 		};
 
 		/* Debugging console UART connected to AB8505 USB */
@@ -285,13 +322,17 @@
 
 		prcmu@80157000 {
 			ab8505 {
-				ab8500_usb {
+				phy {
 					pinctrl-names = "default", "sleep";
 					pinctrl-0 = <&usb_a_1_default>;
 					pinctrl-1 = <&usb_a_1_sleep>;
 				};
 
-				ab8505-regulators {
+				ab8500_fg {
+					line-impedance-micro-ohms = <16000>;
+				};
+
+				regulator {
 					ab8500_ldo_aux1 {
 						/* Used for VDD for sensors */
 						regulator-name = "AUX1";
@@ -635,6 +676,20 @@
 			};
 		};
 	};
+	g05ta03 {
+		g05ta03_skomer_default: g05ta03 {
+			/* Reset line, start out de-asserted */
+			skomer_cfg1 {
+				pins = "GPIO209_AG15";
+				ste,config = <&gpio_out_hi>;
+			};
+			/* GPS_ON_OFF, start out deasserted (off) */
+			skomer_cfg2 {
+				pins = "GPIO86_C6";
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
 };
 
 &ab8505_gpio {
diff --git a/arch/arm/boot/dts/stih407-clock.dtsi b/arch/arm/boot/dts/stih407-clock.dtsi
index 9cce9541e26b..350bcfcf498b 100644
--- a/arch/arm/boot/dts/stih407-clock.dtsi
+++ b/arch/arm/boot/dts/stih407-clock.dtsi
@@ -29,7 +29,7 @@
 		 */
 		clockgen-a9@92b0000 {
 			compatible = "st,clkgen-c32";
-			reg = <0x92b0000 0xffff>;
+			reg = <0x92b0000 0x10000>;
 
 			clockgen_a9_pll: clockgen-a9-pll {
 				#clock-cells = <1>;
@@ -37,32 +37,27 @@
 
 				clocks = <&clk_sysin>;
 			};
-		};
 
-		/*
-		 * ARM CPU related clocks.
-		 */
-		clk_m_a9: clk-m-a9@92b0000 {
-			#clock-cells = <0>;
-			compatible = "st,stih407-clkgen-a9-mux";
-			reg = <0x92b0000 0x10000>;
-
-			clocks = <&clockgen_a9_pll 0>,
-				 <&clockgen_a9_pll 0>,
-				 <&clk_s_c0_flexgen 13>,
-				 <&clk_m_a9_ext2f_div2>;
+			clk_m_a9: clk-m-a9 {
+				#clock-cells = <0>;
+				compatible = "st,stih407-clkgen-a9-mux";
 
+				clocks = <&clockgen_a9_pll 0>,
+					 <&clockgen_a9_pll 0>,
+					 <&clk_s_c0_flexgen 13>,
+					 <&clk_m_a9_ext2f_div2>;
 
-			/*
-			 * ARM Peripheral clock for timers
-			 */
-			arm_periph_clk: clk-m-a9-periphs {
-				#clock-cells = <0>;
-				compatible = "fixed-factor-clock";
+				/*
+				 * ARM Peripheral clock for timers
+				 */
+				arm_periph_clk: clk-m-a9-periphs {
+					#clock-cells = <0>;
+					compatible = "fixed-factor-clock";
 
-				clocks = <&clk_m_a9>;
-				clock-div = <2>;
-				clock-mult = <1>;
+					clocks = <&clk_m_a9>;
+					clock-div = <2>;
+					clock-mult = <1>;
+				};
 			};
 		};
 
@@ -87,14 +82,6 @@
 			};
 		};
 
-		clk_s_c0_quadfs: clk-s-c0-quadfs@9103000 {
-			#clock-cells = <1>;
-			compatible = "st,quadfs-pll";
-			reg = <0x9103000 0x1000>;
-
-			clocks = <&clk_sysin>;
-		};
-
 		clk_s_c0: clockgen-c@9103000 {
 			compatible = "st,clkgen-c32";
 			reg = <0x9103000 0x1000>;
@@ -113,6 +100,13 @@
 				clocks = <&clk_sysin>;
 			};
 
+			clk_s_c0_quadfs: clk-s-c0-quadfs {
+				#clock-cells = <1>;
+				compatible = "st,quadfs-pll";
+
+				clocks = <&clk_sysin>;
+			};
+
 			clk_s_c0_flexgen: clk-s-c0-flexgen {
 				#clock-cells = <1>;
 				compatible = "st,flexgen", "st,flexgen-stih407-c0";
@@ -142,18 +136,17 @@
 			};
 		};
 
-		clk_s_d0_quadfs: clk-s-d0-quadfs@9104000 {
-			#clock-cells = <1>;
-			compatible = "st,quadfs-d0";
-			reg = <0x9104000 0x1000>;
-
-			clocks = <&clk_sysin>;
-		};
-
 		clockgen-d0@9104000 {
 			compatible = "st,clkgen-c32";
 			reg = <0x9104000 0x1000>;
 
+			clk_s_d0_quadfs: clk-s-d0-quadfs {
+				#clock-cells = <1>;
+				compatible = "st,quadfs-d0";
+
+				clocks = <&clk_sysin>;
+			};
+
 			clk_s_d0_flexgen: clk-s-d0-flexgen {
 				#clock-cells = <1>;
 				compatible = "st,flexgen", "st,flexgen-stih407-d0";
@@ -166,18 +159,17 @@
 			};
 		};
 
-		clk_s_d2_quadfs: clk-s-d2-quadfs@9106000 {
-			#clock-cells = <1>;
-			compatible = "st,quadfs-d2";
-			reg = <0x9106000 0x1000>;
-
-			clocks = <&clk_sysin>;
-		};
-
 		clockgen-d2@9106000 {
 			compatible = "st,clkgen-c32";
 			reg = <0x9106000 0x1000>;
 
+			clk_s_d2_quadfs: clk-s-d2-quadfs {
+				#clock-cells = <1>;
+				compatible = "st,quadfs-d2";
+
+				clocks = <&clk_sysin>;
+			};
+
 			clk_s_d2_flexgen: clk-s-d2-flexgen {
 				#clock-cells = <1>;
 				compatible = "st,flexgen", "st,flexgen-stih407-d2";
@@ -192,18 +184,17 @@
 			};
 		};
 
-		clk_s_d3_quadfs: clk-s-d3-quadfs@9107000 {
-			#clock-cells = <1>;
-			compatible = "st,quadfs-d3";
-			reg = <0x9107000 0x1000>;
-
-			clocks = <&clk_sysin>;
-		};
-
 		clockgen-d3@9107000 {
 			compatible = "st,clkgen-c32";
 			reg = <0x9107000 0x1000>;
 
+			clk_s_d3_quadfs: clk-s-d3-quadfs {
+				#clock-cells = <1>;
+				compatible = "st,quadfs-d3";
+
+				clocks = <&clk_sysin>;
+			};
+
 			clk_s_d3_flexgen: clk-s-d3-flexgen {
 				#clock-cells = <1>;
 				compatible = "st,flexgen", "st,flexgen-stih407-d3";
diff --git a/arch/arm/boot/dts/stih407-family.dtsi b/arch/arm/boot/dts/stih407-family.dtsi
index 21f3347a91d6..5ebb77947fd9 100644
--- a/arch/arm/boot/dts/stih407-family.dtsi
+++ b/arch/arm/boot/dts/stih407-family.dtsi
@@ -115,37 +115,140 @@
 		status = "okay";
 	};
 
-	soc {
+	restart: restart-controller {
+		compatible = "st,stih407-restart";
+		st,syscfg = <&syscfg_sbc_reg>;
+		status = "okay";
+	};
+
+	powerdown: powerdown-controller {
+		compatible = "st,stih407-powerdown";
+		#reset-cells = <1>;
+	};
+
+	softreset: softreset-controller {
+		compatible = "st,stih407-softreset";
+		#reset-cells = <1>;
+	};
+
+	picophyreset: picophyreset-controller {
+		compatible = "st,stih407-picophyreset";
+		#reset-cells = <1>;
+	};
+
+	irq-syscfg {
+		compatible = "st,stih407-irq-syscfg";
+		st,syscfg = <&syscfg_core>;
+		st,irq-device = <ST_IRQ_SYSCFG_PMU_0>,
+				<ST_IRQ_SYSCFG_PMU_1>;
+		st,fiq-device = <ST_IRQ_SYSCFG_DISABLED>,
+				<ST_IRQ_SYSCFG_DISABLED>;
+	};
+
+	usb2_picophy0: phy1 {
+		compatible = "st,stih407-usb2-phy";
+		#phy-cells = <0>;
+		st,syscfg = <&syscfg_core 0x100 0xf4>;
+		resets = <&softreset STIH407_PICOPHY_SOFTRESET>,
+			 <&picophyreset STIH407_PICOPHY2_RESET>;
+		reset-names = "global", "port";
+	};
+
+	miphy28lp_phy: miphy28lp {
+		compatible = "st,miphy28lp-phy";
+		st,syscfg = <&syscfg_core>;
 		#address-cells = <1>;
 		#size-cells = <1>;
-		interrupt-parent = <&intc>;
 		ranges;
-		compatible = "simple-bus";
 
-		restart: restart-controller@0 {
-			compatible = "st,stih407-restart";
-			reg = <0 0>;
-			st,syscfg = <&syscfg_sbc_reg>;
-			status = "okay";
-		};
+		phy_port0: port@9b22000 {
+			reg = <0x9b22000 0xff>,
+			      <0x9b09000 0xff>,
+			      <0x9b04000 0xff>;
+			reg-names = "sata-up",
+				    "pcie-up",
+				    "pipew";
+
+			st,syscfg = <0x114 0x818 0xe0 0xec>;
+			#phy-cells = <1>;
 
-		powerdown: powerdown-controller@0 {
-			compatible = "st,stih407-powerdown";
-			reg = <0 0>;
-			#reset-cells = <1>;
+			reset-names = "miphy-sw-rst";
+			resets = <&softreset STIH407_MIPHY0_SOFTRESET>;
 		};
 
-		softreset: softreset-controller@0 {
-			compatible = "st,stih407-softreset";
-			reg = <0 0>;
-			#reset-cells = <1>;
+		phy_port1: port@9b2a000 {
+			reg = <0x9b2a000 0xff>,
+			      <0x9b19000 0xff>,
+			      <0x9b14000 0xff>;
+			reg-names = "sata-up",
+				    "pcie-up",
+				    "pipew";
+
+			st,syscfg = <0x118 0x81c 0xe4 0xf0>;
+
+			#phy-cells = <1>;
+
+			reset-names = "miphy-sw-rst";
+			resets = <&softreset STIH407_MIPHY1_SOFTRESET>;
 		};
 
-		picophyreset: picophyreset-controller@0 {
-			compatible = "st,stih407-picophyreset";
-			reg = <0 0>;
-			#reset-cells = <1>;
+		phy_port2: port@8f95000 {
+			reg = <0x8f95000 0xff>,
+			      <0x8f90000 0xff>;
+			reg-names = "pipew",
+				    "usb3-up";
+
+			st,syscfg = <0x11c 0x820>;
+
+			#phy-cells = <1>;
+
+			reset-names = "miphy-sw-rst";
+			resets = <&softreset STIH407_MIPHY2_SOFTRESET>;
 		};
+	};
+
+	st231_gp0: st231-gp0 {
+		compatible = "st,st231-rproc";
+		memory-region = <&gp0_reserved>;
+		resets = <&softreset STIH407_ST231_GP0_SOFTRESET>;
+		reset-names = "sw_reset";
+		clocks = <&clk_s_c0_flexgen CLK_ST231_GP_0>;
+		clock-frequency = <600000000>;
+		st,syscfg = <&syscfg_core 0x22c>;
+		#mbox-cells = <1>;
+		mbox-names = "vq0_rx", "vq0_tx", "vq1_rx", "vq1_tx";
+		mboxes = <&mailbox0 0 2>, <&mailbox2 0 1>, <&mailbox0 0 3>, <&mailbox2 0 0>;
+	};
+
+	st231_delta: st231-delta {
+		compatible = "st,st231-rproc";
+		memory-region = <&delta_reserved>;
+		resets = <&softreset STIH407_ST231_DMU_SOFTRESET>;
+		reset-names = "sw_reset";
+		clocks = <&clk_s_c0_flexgen CLK_ST231_DMU>;
+		clock-frequency = <600000000>;
+		st,syscfg = <&syscfg_core 0x224>;
+		#mbox-cells = <1>;
+		mbox-names = "vq0_rx", "vq0_tx", "vq1_rx", "vq1_tx";
+		mboxes = <&mailbox0 0 0>, <&mailbox3 0 1>, <&mailbox0 0 1>, <&mailbox3 0 0>;
+	};
+
+	delta0 {
+		compatible = "st,st-delta";
+		clock-names = "delta",
+			      "delta-st231",
+			      "delta-flash-promip";
+		clocks = <&clk_s_c0_flexgen CLK_VID_DMU>,
+			 <&clk_s_c0_flexgen CLK_ST231_DMU>,
+			 <&clk_s_c0_flexgen CLK_FLASH_PROMIP>;
+	};
+
+	soc {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		interrupt-parent = <&intc>;
+		ranges;
+		compatible = "simple-bus";
 
 		syscfg_sbc: sbc-syscfg@9620000 {
 			compatible = "st,stih407-sbc-syscfg", "syscon";
@@ -189,16 +292,6 @@
 			reg = <0x94b5100 0x1000>;
 		};
 
-		irq-syscfg@0 {
-			compatible    = "st,stih407-irq-syscfg";
-			reg = <0 0>;
-			st,syscfg     = <&syscfg_core>;
-			st,irq-device = <ST_IRQ_SYSCFG_PMU_0>,
-					<ST_IRQ_SYSCFG_PMU_1>;
-			st,fiq-device = <ST_IRQ_SYSCFG_DISABLED>,
-					<ST_IRQ_SYSCFG_DISABLED>;
-		};
-
 		/* Display */
 		vtg_main: sti-vtg-main@8d02800 {
 			compatible = "st,vtg";
@@ -389,70 +482,6 @@
 			status = "disabled";
 		};
 
-		usb2_picophy0: phy1@0 {
-			compatible = "st,stih407-usb2-phy";
-			reg = <0 0>;
-			#phy-cells = <0>;
-			st,syscfg = <&syscfg_core 0x100 0xf4>;
-			resets = <&softreset STIH407_PICOPHY_SOFTRESET>,
-				 <&picophyreset STIH407_PICOPHY2_RESET>;
-			reset-names = "global", "port";
-		};
-
-		miphy28lp_phy: miphy28lp@0 {
-			compatible = "st,miphy28lp-phy";
-			st,syscfg = <&syscfg_core>;
-			#address-cells	= <1>;
-			#size-cells	= <1>;
-			ranges;
-			reg = <0 0>;
-
-			phy_port0: port@9b22000 {
-				reg = <0x9b22000 0xff>,
-				      <0x9b09000 0xff>,
-				      <0x9b04000 0xff>;
-				reg-names = "sata-up",
-					    "pcie-up",
-					    "pipew";
-
-				st,syscfg = <0x114 0x818 0xe0 0xec>;
-				#phy-cells = <1>;
-
-				reset-names = "miphy-sw-rst";
-				resets = <&softreset STIH407_MIPHY0_SOFTRESET>;
-			};
-
-			phy_port1: port@9b2a000 {
-				reg = <0x9b2a000 0xff>,
-				      <0x9b19000 0xff>,
-				      <0x9b14000 0xff>;
-				reg-names = "sata-up",
-					    "pcie-up",
-					    "pipew";
-
-				st,syscfg = <0x118 0x81c 0xe4 0xf0>;
-
-				#phy-cells = <1>;
-
-				reset-names = "miphy-sw-rst";
-				resets = <&softreset STIH407_MIPHY1_SOFTRESET>;
-			};
-
-			phy_port2: port@8f95000 {
-				reg = <0x8f95000 0xff>,
-				      <0x8f90000 0xff>;
-				reg-names = "pipew",
-					    "usb3-up";
-
-				st,syscfg = <0x11c 0x820>;
-
-				#phy-cells = <1>;
-
-				reset-names = "miphy-sw-rst";
-				resets = <&softreset STIH407_MIPHY2_SOFTRESET>;
-			};
-		};
-
 		spi@9840000 {
 			compatible = "st,comms-ssc4-spi";
 			reg = <0x9840000 0x110>;
@@ -681,78 +710,78 @@
 
 
 		st_dwc3: dwc3@8f94000 {
-			compatible	= "st,stih407-dwc3";
-			reg		= <0x08f94000 0x1000>, <0x110 0x4>;
-			reg-names	= "reg-glue", "syscfg-reg";
-			st,syscfg	= <&syscfg_core>;
-			resets		= <&powerdown STIH407_USB3_POWERDOWN>,
-					  <&softreset STIH407_MIPHY2_SOFTRESET>;
-			reset-names	= "powerdown", "softreset";
-			#address-cells	= <1>;
-			#size-cells	= <1>;
-			pinctrl-names	= "default";
-			pinctrl-0	= <&pinctrl_usb3>;
+			compatible = "st,stih407-dwc3";
+			reg = <0x08f94000 0x1000>, <0x110 0x4>;
+			reg-names = "reg-glue", "syscfg-reg";
+			st,syscfg = <&syscfg_core>;
+			resets = <&powerdown STIH407_USB3_POWERDOWN>,
+				 <&softreset STIH407_MIPHY2_SOFTRESET>;
+			reset-names = "powerdown", "softreset";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_usb3>;
 			ranges;
 
 			status = "disabled";
 
-			dwc3: dwc3@9900000 {
-				compatible	= "snps,dwc3";
-				reg		= <0x09900000 0x100000>;
-				interrupts	= <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>;
-				dr_mode		= "host";
-				phy-names	= "usb2-phy", "usb3-phy";
-				phys		= <&usb2_picophy0>,
-						  <&phy_port2 PHY_TYPE_USB3>;
+			dwc3: usb@9900000 {
+				compatible = "snps,dwc3";
+				reg = <0x09900000 0x100000>;
+				interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>;
+				dr_mode = "host";
+				phy-names = "usb2-phy", "usb3-phy";
+				phys = <&usb2_picophy0>,
+				       <&phy_port2 PHY_TYPE_USB3>;
 				snps,dis_u3_susphy_quirk;
 			};
 		};
 
 		/* COMMS PWM Module */
 		pwm0: pwm@9810000 {
-			compatible	= "st,sti-pwm";
-			#pwm-cells	= <2>;
-			reg		= <0x9810000 0x68>;
-			interrupts      = <GIC_SPI 128 IRQ_TYPE_LEVEL_HIGH>;
-			pinctrl-names	= "default";
-			pinctrl-0	= <&pinctrl_pwm0_chan0_default>;
-			clock-names	= "pwm";
-			clocks		= <&clk_sysin>;
+			compatible = "st,sti-pwm";
+			#pwm-cells = <2>;
+			reg = <0x9810000 0x68>;
+			interrupts = <GIC_SPI 128 IRQ_TYPE_LEVEL_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_pwm0_chan0_default>;
+			clock-names = "pwm";
+			clocks = <&clk_sysin>;
 			st,pwm-num-chan = <1>;
 
-			status		= "disabled";
+			status = "disabled";
 		};
 
 		/* SBC PWM Module */
 		pwm1: pwm@9510000 {
-			compatible	= "st,sti-pwm";
-			#pwm-cells	= <2>;
-			reg		= <0x9510000 0x68>;
-			interrupts      = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>;
-			pinctrl-names	= "default";
-			pinctrl-0	= <&pinctrl_pwm1_chan0_default
-					&pinctrl_pwm1_chan1_default
-					&pinctrl_pwm1_chan2_default
-					&pinctrl_pwm1_chan3_default>;
-			clock-names	= "pwm";
-			clocks		= <&clk_sysin>;
+			compatible = "st,sti-pwm";
+			#pwm-cells = <2>;
+			reg = <0x9510000 0x68>;
+			interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_pwm1_chan0_default
+				     &pinctrl_pwm1_chan1_default
+				     &pinctrl_pwm1_chan2_default
+				     &pinctrl_pwm1_chan3_default>;
+			clock-names = "pwm";
+			clocks = <&clk_sysin>;
 			st,pwm-num-chan = <4>;
 
-			status		= "disabled";
+			status = "disabled";
 		};
 
 		rng10: rng@8a89000 {
-			compatible      = "st,rng";
-			reg		= <0x08a89000 0x1000>;
-			clocks          = <&clk_sysin>;
-			status		= "okay";
+			compatible = "st,rng";
+			reg = <0x08a89000 0x1000>;
+			clocks = <&clk_sysin>;
+			status = "okay";
 		};
 
 		rng11: rng@8a8a000 {
-			compatible      = "st,rng";
-			reg		= <0x08a8a000 0x1000>;
-			clocks          = <&clk_sysin>;
-			status		= "okay";
+			compatible = "st,rng";
+			reg = <0x08a8a000 0x1000>;
+			clocks = <&clk_sysin>;
+			status = "okay";
 		};
 
 		ethernet0: dwmac@9630000 {
@@ -783,64 +812,36 @@
 		};
 
 		mailbox0: mailbox@8f00000  {
-			compatible	= "st,stih407-mailbox";
-			reg		= <0x8f00000 0x1000>;
-			interrupts	= <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
-			#mbox-cells	= <2>;
-			mbox-name	= "a9";
-			status		= "okay";
+			compatible = "st,stih407-mailbox";
+			reg = <0x8f00000 0x1000>;
+			interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
+			#mbox-cells = <2>;
+			mbox-name = "a9";
+			status = "okay";
 		};
 
 		mailbox1: mailbox@8f01000 {
-			compatible	= "st,stih407-mailbox";
-			reg		= <0x8f01000 0x1000>;
-			#mbox-cells	= <2>;
-			mbox-name	= "st231_gp_1";
-			status		= "okay";
+			compatible = "st,stih407-mailbox";
+			reg = <0x8f01000 0x1000>;
+			#mbox-cells = <2>;
+			mbox-name = "st231_gp_1";
+			status = "okay";
 		};
 
 		mailbox2: mailbox@8f02000 {
-			compatible	= "st,stih407-mailbox";
-			reg		= <0x8f02000 0x1000>;
-			#mbox-cells	= <2>;
-			mbox-name	= "st231_gp_0";
-			status		= "okay";
+			compatible = "st,stih407-mailbox";
+			reg = <0x8f02000 0x1000>;
+			#mbox-cells = <2>;
+			mbox-name = "st231_gp_0";
+			status = "okay";
 		};
 
 		mailbox3: mailbox@8f03000 {
-			compatible	= "st,stih407-mailbox";
-			reg		= <0x8f03000 0x1000>;
-			#mbox-cells	= <2>;
-			mbox-name	= "st231_audio_video";
-			status		= "okay";
-		};
-
-		st231_gp0: st231-gp0@0 {
-			compatible	= "st,st231-rproc";
-			reg		= <0 0>;
-			memory-region	= <&gp0_reserved>;
-			resets		= <&softreset STIH407_ST231_GP0_SOFTRESET>;
-			reset-names	= "sw_reset";
-			clocks		= <&clk_s_c0_flexgen CLK_ST231_GP_0>;
-			clock-frequency	= <600000000>;
-			st,syscfg	= <&syscfg_core 0x22c>;
-			#mbox-cells = <1>;
-			mbox-names = "vq0_rx", "vq0_tx", "vq1_rx", "vq1_tx";
-			mboxes = <&mailbox0 0 2>, <&mailbox2 0 1>, <&mailbox0 0 3>, <&mailbox2 0 0>;
-		};
-
-		st231_delta: st231-delta@0 {
-			compatible	= "st,st231-rproc";
-			reg		= <0 0>;
-			memory-region	= <&delta_reserved>;
-			resets		= <&softreset STIH407_ST231_DMU_SOFTRESET>;
-			reset-names	= "sw_reset";
-			clocks		= <&clk_s_c0_flexgen CLK_ST231_DMU>;
-			clock-frequency	= <600000000>;
-			st,syscfg	= <&syscfg_core 0x224>;
-			#mbox-cells = <1>;
-			mbox-names = "vq0_rx", "vq0_tx", "vq1_rx", "vq1_tx";
-			mboxes = <&mailbox0 0 0>, <&mailbox3 0 1>, <&mailbox0 0 1>, <&mailbox3 0 0>;
+			compatible = "st,stih407-mailbox";
+			reg = <0x8f03000 0x1000>;
+			#mbox-cells = <2>;
+			mbox-name = "st231_audio_video";
+			status = "okay";
 		};
 
 		/* fdma audio */
@@ -912,7 +913,7 @@
 			dmas = <&fdma0 2 0 1>;
 			dma-names = "tx";
 
-			status		= "disabled";
+			status = "disabled";
 		};
 
 		sti_uni_player1: sti-uni-player@8d81000 {
@@ -986,16 +987,5 @@
 
 			status = "disabled";
 		};
-
-		delta0@0 {
-			compatible = "st,st-delta";
-			reg = <0 0>;
-			clock-names = "delta",
-				      "delta-st231",
-				      "delta-flash-promip";
-			clocks = <&clk_s_c0_flexgen CLK_VID_DMU>,
-				 <&clk_s_c0_flexgen CLK_ST231_DMU>,
-				 <&clk_s_c0_flexgen CLK_FLASH_PROMIP>;
-		};
 	};
 };
diff --git a/arch/arm/boot/dts/stih407.dtsi b/arch/arm/boot/dts/stih407.dtsi
index 9e212b0af89d..aca43d2bdaad 100644
--- a/arch/arm/boot/dts/stih407.dtsi
+++ b/arch/arm/boot/dts/stih407.dtsi
@@ -13,7 +13,7 @@
 			#address-cells = <1>;
 			#size-cells = <1>;
 			reg = <0 0>;
-			assigned-clocks	= <&clk_s_d2_quadfs 0>,
+			assigned-clocks = <&clk_s_d2_quadfs 0>,
 					  <&clk_s_d2_quadfs 1>,
 					  <&clk_s_c0_pll1 0>,
 					  <&clk_s_c0_flexgen CLK_COMPO_DVP>,
@@ -106,7 +106,7 @@
 				reg-names = "hdmi-reg";
 				#sound-dai-cells = <0>;
 				interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>;
-				interrupt-names	= "irq";
+				interrupt-names = "irq";
 				clock-names = "pix",
 					      "tmds",
 					      "phy",
diff --git a/arch/arm/boot/dts/stih410-b2120.dts b/arch/arm/boot/dts/stih410-b2120.dts
index 9d3b118f5f0f..538ff98ca1b1 100644
--- a/arch/arm/boot/dts/stih410-b2120.dts
+++ b/arch/arm/boot/dts/stih410-b2120.dts
@@ -24,6 +24,14 @@
 		ethernet0 = &ethernet0;
 	};
 
+	usb2_picophy1: phy2 {
+		status = "okay";
+	};
+
+	usb2_picophy2: phy3 {
+		status = "okay";
+	};
+
 	soc {
 
 		mmc0: sdhci@9060000 {
@@ -33,14 +41,6 @@
 			sd-uhs-ddr50;
 		};
 
-		usb2_picophy1: phy2@0 {
-			status = "okay";
-		};
-
-		usb2_picophy2: phy3@0 {
-			status = "okay";
-		};
-
 		ohci0: usb@9a03c00 {
 			status = "okay";
 		};
diff --git a/arch/arm/boot/dts/stih410-b2260.dts b/arch/arm/boot/dts/stih410-b2260.dts
index 9d579c16c295..26d93f26f6d0 100644
--- a/arch/arm/boot/dts/stih410-b2260.dts
+++ b/arch/arm/boot/dts/stih410-b2260.dts
@@ -75,6 +75,21 @@
 		};
 	};
 
+	miphy28lp_phy: miphy28lp {
+
+		phy_port1: port@9b2a000 {
+			st,osc-force-ext;
+		};
+	};
+
+	usb2_picophy1: phy2 {
+		status = "okay";
+	};
+
+	usb2_picophy2: phy3 {
+		status = "okay";
+	};
+
 	soc {
 		/* Low speed expansion connector */
 		uart0: serial@9830000 {
@@ -145,14 +160,6 @@
 			status = "okay";
 		};
 
-		usb2_picophy1: phy2@0 {
-			status = "okay";
-		};
-
-		usb2_picophy2: phy3@0 {
-			status = "okay";
-		};
-
 		ohci0: usb@9a03c00 {
 			status = "okay";
 		};
@@ -196,13 +203,6 @@
 			status = "okay";
 		};
 
-		miphy28lp_phy: miphy28lp@0 {
-
-			phy_port1: port@9b2a000 {
-				st,osc-force-ext;
-			};
-		};
-
 		sata1: sata@9b28000 {
 			status = "okay";
 		};
diff --git a/arch/arm/boot/dts/stih410-clock.dtsi b/arch/arm/boot/dts/stih410-clock.dtsi
index 6b0e6d4477a3..abac98a1810b 100644
--- a/arch/arm/boot/dts/stih410-clock.dtsi
+++ b/arch/arm/boot/dts/stih410-clock.dtsi
@@ -32,7 +32,7 @@
 		 */
 		clockgen-a9@92b0000 {
 			compatible = "st,clkgen-c32";
-			reg = <0x92b0000 0xffff>;
+			reg = <0x92b0000 0x10000>;
 
 			clockgen_a9_pll: clockgen-a9-pll {
 				#clock-cells = <1>;
@@ -40,29 +40,29 @@
 
 				clocks = <&clk_sysin>;
 			};
-		};
 
-		/*
-		 * ARM CPU related clocks.
-		 */
-		clk_m_a9: clk-m-a9@92b0000 {
-			#clock-cells = <0>;
-			compatible = "st,stih407-clkgen-a9-mux", "st,clkgen-mux";
-			reg = <0x92b0000 0x10000>;
-
-			clocks = <&clockgen_a9_pll 0>,
-				 <&clockgen_a9_pll 0>,
-				 <&clk_s_c0_flexgen 13>,
-				 <&clk_m_a9_ext2f_div2>;
 			/*
-			 * ARM Peripheral clock for timers
+			 * ARM CPU related clocks.
 			 */
-			arm_periph_clk: clk-m-a9-periphs {
+			clk_m_a9: clk-m-a9 {
 				#clock-cells = <0>;
-				compatible = "fixed-factor-clock";
-				clocks = <&clk_m_a9>;
-				clock-div = <2>;
-				clock-mult = <1>;
+				compatible = "st,stih407-clkgen-a9-mux", "st,clkgen-mux";
+
+				clocks = <&clockgen_a9_pll 0>,
+					 <&clockgen_a9_pll 0>,
+					 <&clk_s_c0_flexgen 13>,
+					 <&clk_m_a9_ext2f_div2>;
+
+				/*
+				 * ARM Peripheral clock for timers
+				 */
+				arm_periph_clk: clk-m-a9-periphs {
+					#clock-cells = <0>;
+					compatible = "fixed-factor-clock";
+					clocks = <&clk_m_a9>;
+					clock-div = <2>;
+					clock-mult = <1>;
+				};
 			};
 		};
 
@@ -87,14 +87,6 @@
 			};
 		};
 
-		clk_s_c0_quadfs: clk-s-c0-quadfs@9103000 {
-			#clock-cells = <1>;
-			compatible = "st,quadfs-pll";
-			reg = <0x9103000 0x1000>;
-
-			clocks = <&clk_sysin>;
-		};
-
 		clk_s_c0: clockgen-c@9103000 {
 			compatible = "st,clkgen-c32";
 			reg = <0x9103000 0x1000>;
@@ -113,6 +105,13 @@
 				clocks = <&clk_sysin>;
 			};
 
+			clk_s_c0_quadfs: clk-s-c0-quadfs {
+				#clock-cells = <1>;
+				compatible = "st,quadfs-pll";
+
+				clocks = <&clk_sysin>;
+			};
+
 			clk_s_c0_flexgen: clk-s-c0-flexgen {
 				#clock-cells = <1>;
 				compatible = "st,flexgen", "st,flexgen-stih410-c0";
@@ -142,18 +141,17 @@
 			};
 		};
 
-		clk_s_d0_quadfs: clk-s-d0-quadfs@9104000 {
-			#clock-cells = <1>;
-			compatible = "st,quadfs-d0";
-			reg = <0x9104000 0x1000>;
-
-			clocks = <&clk_sysin>;
-		};
-
 		clockgen-d0@9104000 {
 			compatible = "st,clkgen-c32";
 			reg = <0x9104000 0x1000>;
 
+			clk_s_d0_quadfs: clk-s-d0-quadfs {
+				#clock-cells = <1>;
+				compatible = "st,quadfs-d0";
+
+				clocks = <&clk_sysin>;
+			};
+
 			clk_s_d0_flexgen: clk-s-d0-flexgen {
 				#clock-cells = <1>;
 				compatible = "st,flexgen", "st,flexgen-stih410-d0";
@@ -166,18 +164,17 @@
 			};
 		};
 
-		clk_s_d2_quadfs: clk-s-d2-quadfs@9106000 {
-			#clock-cells = <1>;
-			compatible = "st,quadfs-d2";
-			reg = <0x9106000 0x1000>;
-
-			clocks = <&clk_sysin>;
-		};
-
 		clockgen-d2@9106000 {
 			compatible = "st,clkgen-c32";
 			reg = <0x9106000 0x1000>;
 
+			clk_s_d2_quadfs: clk-s-d2-quadfs {
+				#clock-cells = <1>;
+				compatible = "st,quadfs-d2";
+
+				clocks = <&clk_sysin>;
+			};
+
 			clk_s_d2_flexgen: clk-s-d2-flexgen {
 				#clock-cells = <1>;
 				compatible = "st,flexgen", "st,flexgen-stih407-d2";
@@ -192,18 +189,17 @@
 			};
 		};
 
-		clk_s_d3_quadfs: clk-s-d3-quadfs@9107000 {
-			#clock-cells = <1>;
-			compatible = "st,quadfs-d3";
-			reg = <0x9107000 0x1000>;
-
-			clocks = <&clk_sysin>;
-		};
-
 		clockgen-d3@9107000 {
 			compatible = "st,clkgen-c32";
 			reg = <0x9107000 0x1000>;
 
+			clk_s_d3_quadfs: clk-s-d3-quadfs {
+				#clock-cells = <1>;
+				compatible = "st,quadfs-d3";
+
+				clocks = <&clk_sysin>;
+			};
+
 			clk_s_d3_flexgen: clk-s-d3-flexgen {
 				#clock-cells = <1>;
 				compatible = "st,flexgen", "st,flexgen-stih407-d3";
diff --git a/arch/arm/boot/dts/stih410.dtsi b/arch/arm/boot/dts/stih410.dtsi
index 6d847019c554..a39dd5f7bcae 100644
--- a/arch/arm/boot/dts/stih410.dtsi
+++ b/arch/arm/boot/dts/stih410.dtsi
@@ -12,31 +12,29 @@
 		bdisp0 = &bdisp0;
 	};
 
-	soc {
-		usb2_picophy1: phy2@0 {
-			compatible = "st,stih407-usb2-phy";
-			reg = <0 0>;
-			#phy-cells = <0>;
-			st,syscfg = <&syscfg_core 0xf8 0xf4>;
-			resets = <&softreset STIH407_PICOPHY_SOFTRESET>,
-				 <&picophyreset STIH407_PICOPHY0_RESET>;
-			reset-names = "global", "port";
-
-			status = "disabled";
-		};
+	usb2_picophy1: phy2 {
+		compatible = "st,stih407-usb2-phy";
+		#phy-cells = <0>;
+		st,syscfg = <&syscfg_core 0xf8 0xf4>;
+		resets = <&softreset STIH407_PICOPHY_SOFTRESET>,
+			 <&picophyreset STIH407_PICOPHY0_RESET>;
+		reset-names = "global", "port";
+
+		status = "disabled";
+	};
 
-		usb2_picophy2: phy3@0 {
-			compatible = "st,stih407-usb2-phy";
-			reg = <0 0>;
-			#phy-cells = <0>;
-			st,syscfg = <&syscfg_core 0xfc 0xf4>;
-			resets = <&softreset STIH407_PICOPHY_SOFTRESET>,
-				 <&picophyreset STIH407_PICOPHY1_RESET>;
-			reset-names = "global", "port";
+	usb2_picophy2: phy3 {
+		compatible = "st,stih407-usb2-phy";
+		#phy-cells = <0>;
+		st,syscfg = <&syscfg_core 0xfc 0xf4>;
+		resets = <&softreset STIH407_PICOPHY_SOFTRESET>,
+			 <&picophyreset STIH407_PICOPHY1_RESET>;
+		reset-names = "global", "port";
 
-			status = "disabled";
-		};
+		status = "disabled";
+	};
 
+	soc {
 		ohci0: usb@9a03c00 {
 			compatible = "st,st-ohci-300x";
 			reg = <0x9a03c00 0x100>;
@@ -107,7 +105,7 @@
 			#size-cells = <1>;
 
 			reg = <0 0>;
-			assigned-clocks	= <&clk_s_d2_quadfs 0>,
+			assigned-clocks = <&clk_s_d2_quadfs 0>,
 					  <&clk_s_d2_quadfs 1>,
 					  <&clk_s_c0_pll1 0>,
 					  <&clk_s_c0_flexgen CLK_COMPO_DVP>,
@@ -200,7 +198,7 @@
 				reg-names = "hdmi-reg";
 				#sound-dai-cells = <0>;
 				interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>;
-				interrupt-names	= "irq";
+				interrupt-names = "irq";
 				clock-names = "pix",
 					      "tmds",
 					      "phy",
@@ -274,16 +272,6 @@
 			interrupts = <GIC_SPI 205 IRQ_TYPE_EDGE_RISING>;
 		};
 
-		delta0@0 {
-			compatible = "st,st-delta";
-			clock-names = "delta",
-				      "delta-st231",
-				      "delta-flash-promip";
-			clocks = <&clk_s_c0_flexgen CLK_VID_DMU>,
-				 <&clk_s_c0_flexgen CLK_ST231_DMU>,
-				 <&clk_s_c0_flexgen CLK_FLASH_PROMIP>;
-		};
-
 		sti-cec@94a087c {
 			compatible = "st,stih-cec";
 			reg = <0x94a087c 0x64>;
diff --git a/arch/arm/boot/dts/stih418-b2199.dts b/arch/arm/boot/dts/stih418-b2199.dts
index b66e2b29edea..d21bcc7c1271 100644
--- a/arch/arm/boot/dts/stih418-b2199.dts
+++ b/arch/arm/boot/dts/stih418-b2199.dts
@@ -37,6 +37,17 @@
 		};
 	};
 
+	miphy28lp_phy: miphy28lp {
+
+		phy_port0: port@9b22000 {
+			st,osc-rdy;
+		};
+
+		phy_port1: port@9b2a000 {
+			st,osc-force-ext;
+		};
+	};
+
 	soc {
 		sbc_serial0: serial@9530000 {
 			status = "okay";
@@ -84,17 +95,6 @@
 			non-removable;
 		};
 
-		miphy28lp_phy: miphy28lp@0 {
-
-			phy_port0: port@9b22000 {
-				st,osc-rdy;
-			};
-
-			phy_port1: port@9b2a000 {
-				st,osc-force-ext;
-			};
-		};
-
 		st_dwc3: dwc3@8f94000 {
 			status = "okay";
 		};
diff --git a/arch/arm/boot/dts/stih418-clock.dtsi b/arch/arm/boot/dts/stih418-clock.dtsi
index e84c476b83ed..e1749e92a2e7 100644
--- a/arch/arm/boot/dts/stih418-clock.dtsi
+++ b/arch/arm/boot/dts/stih418-clock.dtsi
@@ -32,7 +32,7 @@
 		 */
 		clockgen-a9@92b0000 {
 			compatible = "st,clkgen-c32";
-			reg = <0x92b0000 0xffff>;
+			reg = <0x92b0000 0x10000>;
 
 			clockgen_a9_pll: clockgen-a9-pll {
 				#clock-cells = <1>;
@@ -40,30 +40,29 @@
 
 				clocks = <&clk_sysin>;
 			};
-		};
-
-		/*
-		 * ARM CPU related clocks.
-		 */
-		clk_m_a9: clk-m-a9@92b0000 {
-			#clock-cells = <0>;
-			compatible = "st,stih407-clkgen-a9-mux", "st,clkgen-mux";
-			reg = <0x92b0000 0x10000>;
-
-			clocks = <&clockgen_a9_pll 0>,
-				 <&clockgen_a9_pll 0>,
-				 <&clk_s_c0_flexgen 13>,
-				 <&clk_m_a9_ext2f_div2>;
 
 			/*
-			 * ARM Peripheral clock for timers
+			 * ARM CPU related clocks.
 			 */
-			arm_periph_clk: clk-m-a9-periphs {
+			clk_m_a9: clk-m-a9 {
 				#clock-cells = <0>;
-				compatible = "fixed-factor-clock";
-				clocks = <&clk_m_a9>;
-				clock-div = <2>;
-				clock-mult = <1>;
+				compatible = "st,stih407-clkgen-a9-mux", "st,clkgen-mux";
+
+				clocks = <&clockgen_a9_pll 0>,
+					 <&clockgen_a9_pll 0>,
+					 <&clk_s_c0_flexgen 13>,
+					 <&clk_m_a9_ext2f_div2>;
+
+				/*
+				 * ARM Peripheral clock for timers
+				 */
+				arm_periph_clk: clk-m-a9-periphs {
+					#clock-cells = <0>;
+					compatible = "fixed-factor-clock";
+					clocks = <&clk_m_a9>;
+					clock-div = <2>;
+					clock-mult = <1>;
+				};
 			};
 		};
 
@@ -88,14 +87,6 @@
 			};
 		};
 
-		clk_s_c0_quadfs: clk-s-c0-quadfs@9103000 {
-			#clock-cells = <1>;
-			compatible = "st,quadfs-pll";
-			reg = <0x9103000 0x1000>;
-
-			clocks = <&clk_sysin>;
-		};
-
 		clk_s_c0: clockgen-c@9103000 {
 			compatible = "st,clkgen-c32";
 			reg = <0x9103000 0x1000>;
@@ -114,6 +105,13 @@
 				clocks = <&clk_sysin>;
 			};
 
+			clk_s_c0_quadfs: clk-s-c0-quadfs {
+				#clock-cells = <1>;
+				compatible = "st,quadfs-pll";
+
+				clocks = <&clk_sysin>;
+			};
+
 			clk_s_c0_flexgen: clk-s-c0-flexgen {
 				#clock-cells = <1>;
 				compatible = "st,flexgen", "st,flexgen-stih418-c0";
@@ -143,18 +141,17 @@
 			};
 		};
 
-		clk_s_d0_quadfs: clk-s-d0-quadfs@9104000 {
-			#clock-cells = <1>;
-			compatible = "st,quadfs-d0";
-			reg = <0x9104000 0x1000>;
-
-			clocks = <&clk_sysin>;
-		};
-
 		clockgen-d0@9104000 {
 			compatible = "st,clkgen-c32";
 			reg = <0x9104000 0x1000>;
 
+			clk_s_d0_quadfs: clk-s-d0-quadfs {
+				#clock-cells = <1>;
+				compatible = "st,quadfs-d0";
+
+				clocks = <&clk_sysin>;
+			};
+
 			clk_s_d0_flexgen: clk-s-d0-flexgen {
 				#clock-cells = <1>;
 				compatible = "st,flexgen", "st,flexgen-stih410-d0";
@@ -167,18 +164,17 @@
 			};
 		};
 
-		clk_s_d2_quadfs: clk-s-d2-quadfs@9106000 {
-			#clock-cells = <1>;
-			compatible = "st,quadfs-d2";
-			reg = <0x9106000 0x1000>;
-
-			clocks = <&clk_sysin>;
-		};
-
 		clockgen-d2@9106000 {
 			compatible = "st,clkgen-c32";
 			reg = <0x9106000 0x1000>;
 
+			clk_s_d2_quadfs: clk-s-d2-quadfs {
+				#clock-cells = <1>;
+				compatible = "st,quadfs-d2";
+
+				clocks = <&clk_sysin>;
+			};
+
 			clk_s_d2_flexgen: clk-s-d2-flexgen {
 				#clock-cells = <1>;
 				compatible = "st,flexgen", "st,flexgen-stih418-d2";
@@ -193,18 +189,17 @@
 			};
 		};
 
-		clk_s_d3_quadfs: clk-s-d3-quadfs@9107000 {
-			#clock-cells = <1>;
-			compatible = "st,quadfs-d3";
-			reg = <0x9107000 0x1000>;
-
-			clocks = <&clk_sysin>;
-		};
-
 		clockgen-d3@9107000 {
 			compatible = "st,clkgen-c32";
 			reg = <0x9107000 0x1000>;
 
+			clk_s_d3_quadfs: clk-s-d3-quadfs {
+				#clock-cells = <1>;
+				compatible = "st,quadfs-d3";
+
+				clocks = <&clk_sysin>;
+			};
+
 			clk_s_d3_flexgen: clk-s-d3-flexgen {
 				#clock-cells = <1>;
 				compatible = "st,flexgen", "st,flexgen-stih407-d3";
diff --git a/arch/arm/boot/dts/stih418.dtsi b/arch/arm/boot/dts/stih418.dtsi
index 97eda4392fbe..b35b9b7a7ccc 100644
--- a/arch/arm/boot/dts/stih418.dtsi
+++ b/arch/arm/boot/dts/stih418.dtsi
@@ -26,31 +26,29 @@
 		};
 	};
 
+	usb2_picophy1: phy2 {
+		compatible = "st,stih407-usb2-phy";
+		#phy-cells = <0>;
+		st,syscfg = <&syscfg_core 0xf8 0xf4>;
+		resets = <&softreset STIH407_PICOPHY_SOFTRESET>,
+			 <&picophyreset STIH407_PICOPHY0_RESET>;
+		reset-names = "global", "port";
+	};
+
+	usb2_picophy2: phy3 {
+		compatible = "st,stih407-usb2-phy";
+		#phy-cells = <0>;
+		st,syscfg = <&syscfg_core 0xfc 0xf4>;
+		resets = <&softreset STIH407_PICOPHY_SOFTRESET>,
+			 <&picophyreset STIH407_PICOPHY1_RESET>;
+		reset-names = "global", "port";
+	};
+
 	soc {
 		rng11: rng@8a8a000 {
 			status = "disabled";
 		};
 
-		usb2_picophy1: phy2@0 {
-			compatible = "st,stih407-usb2-phy";
-			reg = <0 0>;
-			#phy-cells = <0>;
-			st,syscfg = <&syscfg_core 0xf8 0xf4>;
-			resets = <&softreset STIH407_PICOPHY_SOFTRESET>,
-				 <&picophyreset STIH407_PICOPHY0_RESET>;
-			reset-names = "global", "port";
-		};
-
-		usb2_picophy2: phy3@0 {
-			compatible = "st,stih407-usb2-phy";
-			reg = <0 0>;
-			#phy-cells = <0>;
-			st,syscfg = <&syscfg_core 0xfc 0xf4>;
-			resets = <&softreset STIH407_PICOPHY_SOFTRESET>,
-				 <&picophyreset STIH407_PICOPHY1_RESET>;
-			reset-names = "global", "port";
-		};
-
 		ohci0: usb@9a03c00 {
 			compatible = "st,st-ohci-300x";
 			reg = <0x9a03c00 0x100>;
diff --git a/arch/arm/boot/dts/stihxxx-b2120.dtsi b/arch/arm/boot/dts/stihxxx-b2120.dtsi
index d051f080e52e..2aa94605d3d4 100644
--- a/arch/arm/boot/dts/stihxxx-b2120.dtsi
+++ b/arch/arm/boot/dts/stihxxx-b2120.dtsi
@@ -71,6 +71,17 @@
 		};
 	};
 
+	miphy28lp_phy: miphy28lp {
+
+		phy_port0: port@9b22000 {
+			st,osc-rdy;
+		};
+
+		phy_port1: port@9b2a000 {
+			st,osc-force-ext;
+		};
+	};
+
 	soc {
 		sbc_serial0: serial@9530000 {
 			status = "okay";
@@ -128,17 +139,6 @@
 			st,i2c-min-sda-pulse-width-us = <5>;
 		};
 
-		miphy28lp_phy: miphy28lp@0 {
-
-			phy_port0: port@9b22000 {
-				st,osc-rdy;
-			};
-
-			phy_port1: port@9b2a000 {
-				st,osc-force-ext;
-			};
-		};
-
 		st_dwc3: dwc3@8f94000 {
 			status = "okay";
 		};
@@ -175,11 +175,11 @@
 
 			/* tsin0 is TSA on NIMA */
 			tsin0: port {
-				tsin-num	= <0>;
+				tsin-num = <0>;
 				serial-not-parallel;
-				i2c-bus		= <&ssc2>;
-				reset-gpios	= <&pio15 4 GPIO_ACTIVE_HIGH>;
-				dvb-card	= <STV0367_TDA18212_NIMA_1>;
+				i2c-bus = <&ssc2>;
+				reset-gpios = <&pio15 4 GPIO_ACTIVE_HIGH>;
+				dvb-card = <STV0367_TDA18212_NIMA_1>;
 			};
 		};
 
diff --git a/arch/arm/boot/dts/stm32429i-eval.dts b/arch/arm/boot/dts/stm32429i-eval.dts
index cb46326a8c75..3de0e9dbe030 100644
--- a/arch/arm/boot/dts/stm32429i-eval.dts
+++ b/arch/arm/boot/dts/stm32429i-eval.dts
@@ -251,10 +251,10 @@
 
 &mac {
 	status = "okay";
-	pinctrl-0	= <&ethernet_mii>;
-	pinctrl-names	= "default";
-	phy-mode	= "mii";
-	phy-handle	= <&phy1>;
+	pinctrl-0 = <&ethernet_mii>;
+	pinctrl-names = "default";
+	phy-mode = "mii";
+	phy-handle = <&phy1>;
 	mdio0 {
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -308,6 +308,18 @@
 	};
 };
 
+&timers5 {
+	/* Override timer5 to act as clockevent */
+	compatible = "st,stm32-timer";
+	interrupts = <50>;
+	status = "okay";
+	/delete-property/#address-cells;
+	/delete-property/#size-cells;
+	/delete-property/clock-names;
+	/delete-node/pwm;
+	/delete-node/timer@4;
+};
+
 &usart1 {
 	pinctrl-0 = <&usart1_pins_a>;
 	pinctrl-names = "default";
diff --git a/arch/arm/boot/dts/stm32746g-eval.dts b/arch/arm/boot/dts/stm32746g-eval.dts
index 327613fd9666..a293e65141c6 100644
--- a/arch/arm/boot/dts/stm32746g-eval.dts
+++ b/arch/arm/boot/dts/stm32746g-eval.dts
@@ -194,6 +194,18 @@
 	bus-width = <4>;
 };
 
+&timers5 {
+	/* Override timer5 to act as clockevent */
+	compatible = "st,stm32-timer";
+	interrupts = <50>;
+	status = "okay";
+	/delete-property/#address-cells;
+	/delete-property/#size-cells;
+	/delete-property/clock-names;
+	/delete-node/pwm;
+	/delete-node/timer@4;
+};
+
 &usart1 {
 	pinctrl-0 = <&usart1_pins_a>;
 	pinctrl-names = "default";
diff --git a/arch/arm/boot/dts/stm32f4-pinctrl.dtsi b/arch/arm/boot/dts/stm32f4-pinctrl.dtsi
index 155d9ffacc83..500bcc302d42 100644
--- a/arch/arm/boot/dts/stm32f4-pinctrl.dtsi
+++ b/arch/arm/boot/dts/stm32f4-pinctrl.dtsi
@@ -45,7 +45,7 @@
 
 / {
 	soc {
-		pinctrl: pin-controller@40020000 {
+		pinctrl: pinctrl@40020000 {
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges = <0 0x40020000 0x3000>;
diff --git a/arch/arm/boot/dts/stm32f429-disco.dts b/arch/arm/boot/dts/stm32f429-disco.dts
index 075ac57d0bf4..3b81228d46a2 100644
--- a/arch/arm/boot/dts/stm32f429-disco.dts
+++ b/arch/arm/boot/dts/stm32f429-disco.dts
@@ -192,7 +192,7 @@
 
 	display: display@1{
 		/* Connect panel-ilitek-9341 to ltdc */
-		compatible = "st,sf-tc240t-9370-t";
+		compatible = "st,sf-tc240t-9370-t", "ilitek,ili9341";
 		reg = <1>;
 		spi-3wire;
 		spi-max-frequency = <10000000>;
@@ -205,6 +205,18 @@
 	};
 };
 
+&timers5 {
+	/* Override timer5 to act as clockevent */
+	compatible = "st,stm32-timer";
+	interrupts = <50>;
+	status = "okay";
+	/delete-property/#address-cells;
+	/delete-property/#size-cells;
+	/delete-property/clock-names;
+	/delete-node/pwm;
+	/delete-node/timer@4;
+};
+
 &usart1 {
 	pinctrl-0 = <&usart1_pins_a>;
 	pinctrl-names = "default";
diff --git a/arch/arm/boot/dts/stm32f429.dtsi b/arch/arm/boot/dts/stm32f429.dtsi
index 8748d5850298..c31ceb821231 100644
--- a/arch/arm/boot/dts/stm32f429.dtsi
+++ b/arch/arm/boot/dts/stm32f429.dtsi
@@ -93,14 +93,6 @@
 			};
 		};
 
-		timer2: timer@40000000 {
-			compatible = "st,stm32-timer";
-			reg = <0x40000000 0x400>;
-			interrupts = <28>;
-			clocks = <&rcc 0 STM32F4_APB1_CLOCK(TIM2)>;
-			status = "disabled";
-		};
-
 		timers2: timers@40000000 {
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -123,14 +115,6 @@
 			};
 		};
 
-		timer3: timer@40000400 {
-			compatible = "st,stm32-timer";
-			reg = <0x40000400 0x400>;
-			interrupts = <29>;
-			clocks = <&rcc 0 STM32F4_APB1_CLOCK(TIM3)>;
-			status = "disabled";
-		};
-
 		timers3: timers@40000400 {
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -153,14 +137,6 @@
 			};
 		};
 
-		timer4: timer@40000800 {
-			compatible = "st,stm32-timer";
-			reg = <0x40000800 0x400>;
-			interrupts = <30>;
-			clocks = <&rcc 0 STM32F4_APB1_CLOCK(TIM4)>;
-			status = "disabled";
-		};
-
 		timers4: timers@40000800 {
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -183,13 +159,6 @@
 			};
 		};
 
-		timer5: timer@40000c00 {
-			compatible = "st,stm32-timer";
-			reg = <0x40000c00 0x400>;
-			interrupts = <50>;
-			clocks = <&rcc 0 STM32F4_APB1_CLOCK(TIM5)>;
-		};
-
 		timers5: timers@40000c00 {
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -212,14 +181,6 @@
 			};
 		};
 
-		timer6: timer@40001000 {
-			compatible = "st,stm32-timer";
-			reg = <0x40001000 0x400>;
-			interrupts = <54>;
-			clocks = <&rcc 0 STM32F4_APB1_CLOCK(TIM6)>;
-			status = "disabled";
-		};
-
 		timers6: timers@40001000 {
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -236,14 +197,6 @@
 			};
 		};
 
-		timer7: timer@40001400 {
-			compatible = "st,stm32-timer";
-			reg = <0x40001400 0x400>;
-			interrupts = <55>;
-			clocks = <&rcc 0 STM32F4_APB1_CLOCK(TIM7)>;
-			status = "disabled";
-		};
-
 		timers7: timers@40001400 {
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -759,6 +712,16 @@
 			status = "disabled";
 		};
 
+		dma2d: dma2d@4002b000 {
+			compatible = "st,stm32-dma2d";
+			reg = <0x4002b000 0xc00>;
+			interrupts = <90>;
+			resets = <&rcc STM32F4_AHB1_RESET(DMA2D)>;
+			clocks = <&rcc 0 STM32F4_AHB1_CLOCK(DMA2D)>;
+			clock-names = "dma2d";
+			status = "disabled";
+		};
+
 		usbotg_hs: usb@40040000 {
 			compatible = "snps,dwc2";
 			reg = <0x40040000 0x40000>;
diff --git a/arch/arm/boot/dts/stm32f469-disco.dts b/arch/arm/boot/dts/stm32f469-disco.dts
index 30905ce672a0..5a0daf8e8b11 100644
--- a/arch/arm/boot/dts/stm32f469-disco.dts
+++ b/arch/arm/boot/dts/stm32f469-disco.dts
@@ -132,6 +132,10 @@
 	clock-frequency = <8000000>;
 };
 
+&dma2d {
+	status = "okay";
+};
+
 &dsi {
 	#address-cells = <1>;
 	#size-cells = <0>;
@@ -224,6 +228,18 @@
 	bus-width = <4>;
 };
 
+&timers5 {
+	/* Override timer5 to act as clockevent */
+	compatible = "st,stm32-timer";
+	interrupts = <50>;
+	status = "okay";
+	/delete-property/#address-cells;
+	/delete-property/#size-cells;
+	/delete-property/clock-names;
+	/delete-node/pwm;
+	/delete-node/timer@4;
+};
+
 &usart3 {
 	pinctrl-0 = <&usart3_pins_a>;
 	pinctrl-names = "default";
diff --git a/arch/arm/boot/dts/stm32f7-pinctrl.dtsi b/arch/arm/boot/dts/stm32f7-pinctrl.dtsi
index 1cf8a23c2644..8f37aefa7315 100644
--- a/arch/arm/boot/dts/stm32f7-pinctrl.dtsi
+++ b/arch/arm/boot/dts/stm32f7-pinctrl.dtsi
@@ -9,7 +9,7 @@
 
 / {
 	soc {
-		pinctrl: pin-controller@40020000 {
+		pinctrl: pinctrl@40020000 {
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges = <0 0x40020000 0x3000>;
diff --git a/arch/arm/boot/dts/stm32f746-disco.dts b/arch/arm/boot/dts/stm32f746-disco.dts
index 569d23cc61e5..c11616ed5fc6 100644
--- a/arch/arm/boot/dts/stm32f746-disco.dts
+++ b/arch/arm/boot/dts/stm32f746-disco.dts
@@ -109,6 +109,18 @@
 	bus-width = <4>;
 };
 
+&timers5 {
+	/* Override timer5 to act as clockevent */
+	compatible = "st,stm32-timer";
+	interrupts = <50>;
+	status = "okay";
+	/delete-property/#address-cells;
+	/delete-property/#size-cells;
+	/delete-property/clock-names;
+	/delete-node/pwm;
+	/delete-node/timer@4;
+};
+
 &usart1 {
 	pinctrl-0 = <&usart1_pins_b>;
 	pinctrl-names = "default";
diff --git a/arch/arm/boot/dts/stm32f746.dtsi b/arch/arm/boot/dts/stm32f746.dtsi
index 014b416f57e6..dc868e6da40e 100644
--- a/arch/arm/boot/dts/stm32f746.dtsi
+++ b/arch/arm/boot/dts/stm32f746.dtsi
@@ -75,14 +75,6 @@
 	};
 
 	soc {
-		timer2: timer@40000000 {
-			compatible = "st,stm32-timer";
-			reg = <0x40000000 0x400>;
-			interrupts = <28>;
-			clocks = <&rcc 0 STM32F7_APB1_CLOCK(TIM2)>;
-			status = "disabled";
-		};
-
 		timers2: timers@40000000 {
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -105,14 +97,6 @@
 			};
 		};
 
-		timer3: timer@40000400 {
-			compatible = "st,stm32-timer";
-			reg = <0x40000400 0x400>;
-			interrupts = <29>;
-			clocks = <&rcc 0 STM32F7_APB1_CLOCK(TIM3)>;
-			status = "disabled";
-		};
-
 		timers3: timers@40000400 {
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -135,14 +119,6 @@
 			};
 		};
 
-		timer4: timer@40000800 {
-			compatible = "st,stm32-timer";
-			reg = <0x40000800 0x400>;
-			interrupts = <30>;
-			clocks = <&rcc 0 STM32F7_APB1_CLOCK(TIM4)>;
-			status = "disabled";
-		};
-
 		timers4: timers@40000800 {
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -165,13 +141,6 @@
 			};
 		};
 
-		timer5: timer@40000c00 {
-			compatible = "st,stm32-timer";
-			reg = <0x40000c00 0x400>;
-			interrupts = <50>;
-			clocks = <&rcc 0 STM32F7_APB1_CLOCK(TIM5)>;
-		};
-
 		timers5: timers@40000c00 {
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -194,14 +163,6 @@
 			};
 		};
 
-		timer6: timer@40001000 {
-			compatible = "st,stm32-timer";
-			reg = <0x40001000 0x400>;
-			interrupts = <54>;
-			clocks = <&rcc 0 STM32F7_APB1_CLOCK(TIM6)>;
-			status = "disabled";
-		};
-
 		timers6: timers@40001000 {
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -218,14 +179,6 @@
 			};
 		};
 
-		timer7: timer@40001400 {
-			compatible = "st,stm32-timer";
-			reg = <0x40001400 0x400>;
-			interrupts = <55>;
-			clocks = <&rcc 0 STM32F7_APB1_CLOCK(TIM7)>;
-			status = "disabled";
-		};
-
 		timers7: timers@40001400 {
 			#address-cells = <1>;
 			#size-cells = <0>;
diff --git a/arch/arm/boot/dts/stm32f769-disco.dts b/arch/arm/boot/dts/stm32f769-disco.dts
index be943b701980..b038d0ed39e8 100644
--- a/arch/arm/boot/dts/stm32f769-disco.dts
+++ b/arch/arm/boot/dts/stm32f769-disco.dts
@@ -137,6 +137,18 @@
 	bus-width = <4>;
 };
 
+&timers5 {
+	/* Override timer5 to act as clockevent */
+	compatible = "st,stm32-timer";
+	interrupts = <50>;
+	status = "okay";
+	/delete-property/#address-cells;
+	/delete-property/#size-cells;
+	/delete-property/clock-names;
+	/delete-node/pwm;
+	/delete-node/timer@4;
+};
+
 &usart1 {
 	pinctrl-0 = <&usart1_pins_a>;
 	pinctrl-names = "default";
diff --git a/arch/arm/boot/dts/stm32h743.dtsi b/arch/arm/boot/dts/stm32h743.dtsi
index 6e42ca2dada2..2059593da21d 100644
--- a/arch/arm/boot/dts/stm32h743.dtsi
+++ b/arch/arm/boot/dts/stm32h743.dtsi
@@ -375,7 +375,7 @@
 			arm,primecell-periphid = <0x10153180>;
 			reg = <0x52007000 0x1000>;
 			interrupts = <49>;
-			interrupt-names	= "cmd_irq";
+			interrupt-names = "cmd_irq";
 			clocks = <&rcc SDMMC1_CK>;
 			clock-names = "apb_pclk";
 			resets = <&rcc STM32H7_AHB3_RESET(SDMMC1)>;
@@ -389,7 +389,7 @@
 			arm,primecell-periphid = <0x10153180>;
 			reg = <0x48022400 0x400>;
 			interrupts = <124>;
-			interrupt-names	= "cmd_irq";
+			interrupt-names = "cmd_irq";
 			clocks = <&rcc SDMMC2_CK>;
 			clock-names = "apb_pclk";
 			resets = <&rcc STM32H7_AHB2_RESET(SDMMC2)>;
@@ -583,7 +583,7 @@
 			status = "disabled";
 		};
 
-		pinctrl: pin-controller@58020000 {
+		pinctrl: pinctrl@58020000 {
 			#address-cells = <1>;
 			#size-cells = <1>;
 			compatible = "st,stm32h743-pinctrl";
diff --git a/arch/arm/boot/dts/stm32h743i-disco.dts b/arch/arm/boot/dts/stm32h743i-disco.dts
index 59e01ce10318..2b452883a708 100644
--- a/arch/arm/boot/dts/stm32h743i-disco.dts
+++ b/arch/arm/boot/dts/stm32h743i-disco.dts
@@ -77,10 +77,10 @@
 
 &mac {
 	status = "disabled";
-	pinctrl-0	= <&ethernet_rmii>;
-	pinctrl-names	= "default";
-	phy-mode	= "rmii";
-	phy-handle	= <&phy0>;
+	pinctrl-0 = <&ethernet_rmii>;
+	pinctrl-names = "default";
+	phy-mode = "rmii";
+	phy-handle = <&phy0>;
 
 	mdio0 {
 		#address-cells = <1>;
diff --git a/arch/arm/boot/dts/stm32h743i-eval.dts b/arch/arm/boot/dts/stm32h743i-eval.dts
index 38cc7faf6884..5c5d8059bdc7 100644
--- a/arch/arm/boot/dts/stm32h743i-eval.dts
+++ b/arch/arm/boot/dts/stm32h743i-eval.dts
@@ -115,10 +115,10 @@
 
 &mac {
 	status = "disabled";
-	pinctrl-0	= <&ethernet_rmii>;
-	pinctrl-names	= "default";
-	phy-mode	= "rmii";
-	phy-handle	= <&phy0>;
+	pinctrl-0 = <&ethernet_rmii>;
+	pinctrl-names = "default";
+	phy-mode = "rmii";
+	phy-handle = <&phy0>;
 
 	mdio0 {
 		#address-cells = <1>;
diff --git a/arch/arm/boot/dts/stm32h750i-art-pi.dts b/arch/arm/boot/dts/stm32h750i-art-pi.dts
index 9bb73bb61901..f3e70d3b65ac 100644
--- a/arch/arm/boot/dts/stm32h750i-art-pi.dts
+++ b/arch/arm/boot/dts/stm32h750i-art-pi.dts
@@ -126,10 +126,10 @@
 
 &mac {
 	status = "disabled";
-	pinctrl-0	= <&ethernet_rmii>;
-	pinctrl-names	= "default";
-	phy-mode	= "rmii";
-	phy-handle	= <&phy0>;
+	pinctrl-0 = <&ethernet_rmii>;
+	pinctrl-names = "default";
+	phy-mode = "rmii";
+	phy-handle = <&phy0>;
 
 	mdio0 {
 		#address-cells = <1>;
diff --git a/arch/arm/boot/dts/stm32mp13-pinctrl.dtsi b/arch/arm/boot/dts/stm32mp13-pinctrl.dtsi
index 069f95f2b628..efdd163eba30 100644
--- a/arch/arm/boot/dts/stm32mp13-pinctrl.dtsi
+++ b/arch/arm/boot/dts/stm32mp13-pinctrl.dtsi
@@ -6,8 +6,42 @@
 #include <dt-bindings/pinctrl/stm32-pinfunc.h>
 
 &pinctrl {
+	i2c1_pins_a: i2c1-0 {
+		pins {
+			pinmux = <STM32_PINMUX('D', 12, AF5)>, /* I2C1_SCL */
+				 <STM32_PINMUX('E', 8, AF5)>; /* I2C1_SDA */
+			bias-disable;
+			drive-open-drain;
+			slew-rate = <0>;
+		};
+	};
+
+	i2c1_sleep_pins_a: i2c1-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('D', 12, ANALOG)>, /* I2C1_SCL */
+				 <STM32_PINMUX('E', 8, ANALOG)>; /* I2C1_SDA */
+		};
+	};
+
+	i2c5_pins_a: i2c5-0 {
+		pins {
+			pinmux = <STM32_PINMUX('D', 1, AF4)>, /* I2C5_SCL */
+				 <STM32_PINMUX('H', 6, AF4)>; /* I2C5_SDA */
+			bias-disable;
+			drive-open-drain;
+			slew-rate = <0>;
+		};
+	};
+
+	i2c5_sleep_pins_a: i2c5-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('D', 1, ANALOG)>, /* I2C5_SCL */
+				 <STM32_PINMUX('H', 6, ANALOG)>; /* I2C5_SDA */
+		};
+	};
+
 	sdmmc1_b4_pins_a: sdmmc1-b4-0 {
-		pins1 {
+		pins {
 			pinmux = <STM32_PINMUX('C', 8, AF12)>, /* SDMMC1_D0 */
 				 <STM32_PINMUX('C', 9, AF12)>, /* SDMMC1_D1 */
 				 <STM32_PINMUX('C', 10, AF12)>, /* SDMMC1_D2 */
@@ -17,12 +51,6 @@
 			drive-push-pull;
 			bias-disable;
 		};
-		pins2 {
-			pinmux = <STM32_PINMUX('C', 12, AF12)>; /* SDMMC1_CK */
-			slew-rate = <2>;
-			drive-push-pull;
-			bias-disable;
-		};
 	};
 
 	sdmmc1_b4_od_pins_a: sdmmc1-b4-od-0 {
@@ -36,16 +64,104 @@
 			bias-disable;
 		};
 		pins2 {
+			pinmux = <STM32_PINMUX('D', 2, AF12)>; /* SDMMC1_CMD */
+			slew-rate = <1>;
+			drive-open-drain;
+			bias-disable;
+		};
+	};
+
+	sdmmc1_b4_sleep_pins_a: sdmmc1-b4-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('C', 8, ANALOG)>, /* SDMMC1_D0 */
+				 <STM32_PINMUX('C', 9, ANALOG)>, /* SDMMC1_D1 */
+				 <STM32_PINMUX('C', 10, ANALOG)>, /* SDMMC1_D2 */
+				 <STM32_PINMUX('C', 11, ANALOG)>, /* SDMMC1_D3 */
+				 <STM32_PINMUX('C', 12, ANALOG)>, /* SDMMC1_CK */
+				 <STM32_PINMUX('D', 2, ANALOG)>; /* SDMMC1_CMD */
+		};
+	};
+
+	sdmmc1_clk_pins_a: sdmmc1-clk-0 {
+		pins {
 			pinmux = <STM32_PINMUX('C', 12, AF12)>; /* SDMMC1_CK */
-			slew-rate = <2>;
+			slew-rate = <1>;
 			drive-push-pull;
 			bias-disable;
 		};
-		pins3 {
-			pinmux = <STM32_PINMUX('D', 2, AF12)>; /* SDMMC1_CMD */
+	};
+
+	sdmmc2_b4_pins_a: sdmmc2-b4-0 {
+		pins {
+			pinmux = <STM32_PINMUX('B', 14, AF10)>, /* SDMMC2_D0 */
+				 <STM32_PINMUX('B', 15, AF10)>, /* SDMMC2_D1 */
+				 <STM32_PINMUX('B', 3, AF10)>, /* SDMMC2_D2 */
+				 <STM32_PINMUX('B', 4, AF10)>, /* SDMMC2_D3 */
+				 <STM32_PINMUX('G', 6, AF10)>; /* SDMMC2_CMD */
+			slew-rate = <1>;
+			drive-push-pull;
+			bias-pull-up;
+		};
+	};
+
+	sdmmc2_b4_od_pins_a: sdmmc2-b4-od-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('B', 14, AF10)>, /* SDMMC2_D0 */
+				 <STM32_PINMUX('B', 15, AF10)>, /* SDMMC2_D1 */
+				 <STM32_PINMUX('B', 3, AF10)>, /* SDMMC2_D2 */
+				 <STM32_PINMUX('B', 4, AF10)>; /* SDMMC2_D3 */
+			slew-rate = <1>;
+			drive-push-pull;
+			bias-pull-up;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('G', 6, AF10)>; /* SDMMC2_CMD */
 			slew-rate = <1>;
 			drive-open-drain;
+			bias-pull-up;
+		};
+	};
+
+	sdmmc2_b4_sleep_pins_a: sdmmc2-b4-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('B', 14, ANALOG)>, /* SDMMC2_D0 */
+				 <STM32_PINMUX('B', 15, ANALOG)>, /* SDMMC2_D1 */
+				 <STM32_PINMUX('B', 3, ANALOG)>, /* SDMMC2_D2 */
+				 <STM32_PINMUX('B', 4, ANALOG)>, /* SDMMC2_D3 */
+				 <STM32_PINMUX('E', 3, ANALOG)>, /* SDMMC2_CK */
+				 <STM32_PINMUX('G', 6, ANALOG)>; /* SDMMC2_CMD */
+		};
+	};
+
+	sdmmc2_clk_pins_a: sdmmc2-clk-0 {
+		pins {
+			pinmux = <STM32_PINMUX('E', 3, AF10)>; /* SDMMC2_CK */
+			slew-rate = <1>;
+			drive-push-pull;
+			bias-pull-up;
+		};
+	};
+
+	spi5_pins_a: spi5-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('H', 7, AF6)>, /* SPI5_SCK */
+				 <STM32_PINMUX('H', 3, AF5)>; /* SPI5_MOSI */
 			bias-disable;
+			drive-push-pull;
+			slew-rate = <1>;
+		};
+
+		pins2 {
+			pinmux = <STM32_PINMUX('A', 8, AF5)>; /* SPI5_MISO */
+			bias-disable;
+		};
+	};
+
+	spi5_sleep_pins_a: spi5-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('H', 7, ANALOG)>, /* SPI5_SCK */
+				 <STM32_PINMUX('A', 8, ANALOG)>, /* SPI5_MISO */
+				 <STM32_PINMUX('H', 3, ANALOG)>; /* SPI5_MOSI */
 		};
 	};
 
diff --git a/arch/arm/boot/dts/stm32mp131.dtsi b/arch/arm/boot/dts/stm32mp131.dtsi
index 86126dc0d898..dd35a607073d 100644
--- a/arch/arm/boot/dts/stm32mp131.dtsi
+++ b/arch/arm/boot/dts/stm32mp131.dtsi
@@ -4,6 +4,8 @@
  * Author: Alexandre Torgue <alexandre.torgue@foss.st.com> for STMicroelectronics.
  */
 #include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/stm32mp13-clks.h>
+#include <dt-bindings/reset/stm32mp13-resets.h>
 
 / {
 	#address-cells = <1>;
@@ -27,53 +29,28 @@
 		interrupt-parent = <&intc>;
 	};
 
-	clocks {
-		clk_axi: clk-axi {
-			#clock-cells = <0>;
-			compatible = "fixed-clock";
-			clock-frequency = <266500000>;
+	firmware {
+		optee {
+			method = "smc";
+			compatible = "linaro,optee-tz";
 		};
 
-		clk_hse: clk-hse {
-			#clock-cells = <0>;
-			compatible = "fixed-clock";
-			clock-frequency = <24000000>;
-		};
-
-		clk_hsi: clk-hsi {
-			#clock-cells = <0>;
-			compatible = "fixed-clock";
-			clock-frequency = <64000000>;
-		};
-
-		clk_lsi: clk-lsi {
-			#clock-cells = <0>;
-			compatible = "fixed-clock";
-			clock-frequency = <32000>;
-		};
-
-		clk_pclk3: clk-pclk3 {
-			#clock-cells = <0>;
-			compatible = "fixed-clock";
-			clock-frequency = <104438965>;
-		};
-
-		clk_pclk4: clk-pclk4 {
-			#clock-cells = <0>;
-			compatible = "fixed-clock";
-			clock-frequency = <133250000>;
-		};
+		scmi: scmi {
+			compatible = "linaro,scmi-optee";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			linaro,optee-channel-id = <0>;
+			shmem = <&scmi_shm>;
 
-		clk_pll4_p: clk-pll4_p {
-			#clock-cells = <0>;
-			compatible = "fixed-clock";
-			clock-frequency = <50000000>;
-		};
+			scmi_clk: protocol@14 {
+				reg = <0x14>;
+				#clock-cells = <1>;
+			};
 
-		clk_pll4_r: clk-pll4_r {
-			#clock-cells = <0>;
-			compatible = "fixed-clock";
-			clock-frequency = <99000000>;
+			scmi_reset: protocol@16 {
+				reg = <0x16>;
+				#reset-cells = <1>;
+			};
 		};
 	};
 
@@ -92,10 +69,10 @@
 
 	timer {
 		compatible = "arm,armv7-timer";
-		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
-			     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
-			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
-			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>;
 		interrupt-parent = <&intc>;
 		always-on;
 	};
@@ -107,42 +84,319 @@
 		interrupt-parent = <&intc>;
 		ranges;
 
+		scmi_sram: sram@2ffff000 {
+			compatible = "mmio-sram";
+			reg = <0x2ffff000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x2ffff000 0x1000>;
+
+			scmi_shm: scmi-sram@0 {
+				compatible = "arm,scmi-shmem";
+				reg = <0 0x80>;
+			};
+		};
+
+		spi2: spi@4000b000 {
+			compatible = "st,stm32h7-spi";
+			reg = <0x4000b000 0x400>;
+			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc SPI2_K>;
+			resets = <&rcc SPI2_R>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			dmas = <&dmamux1 39 0x400 0x01>,
+			       <&dmamux1 40 0x400 0x01>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		spi3: spi@4000c000 {
+			compatible = "st,stm32h7-spi";
+			reg = <0x4000c000 0x400>;
+			interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc SPI3_K>;
+			resets = <&rcc SPI3_R>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			dmas = <&dmamux1 61 0x400 0x01>,
+			       <&dmamux1 62 0x400 0x01>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
 		uart4: serial@40010000 {
 			compatible = "st,stm32h7-uart";
 			reg = <0x40010000 0x400>;
 			interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&clk_hsi>;
+			clocks = <&rcc UART4_K>;
+			resets = <&rcc UART4_R>;
+			status = "disabled";
+		};
+
+		i2c1: i2c@40012000 {
+			compatible = "st,stm32mp13-i2c";
+			reg = <0x40012000 0x400>;
+			interrupt-names = "event", "error";
+			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc I2C1_K>;
+			resets = <&rcc I2C1_R>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			dmas = <&dmamux1 33 0x400 0x1>,
+			       <&dmamux1 34 0x400 0x1>;
+			dma-names = "rx", "tx";
+			st,syscfg-fmp = <&syscfg 0x4 0x1>;
+			i2c-analog-filter;
 			status = "disabled";
 		};
 
+		i2c2: i2c@40013000 {
+			compatible = "st,stm32mp13-i2c";
+			reg = <0x40013000 0x400>;
+			interrupt-names = "event", "error";
+			interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc I2C2_K>;
+			resets = <&rcc I2C2_R>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			dmas = <&dmamux1 35 0x400 0x1>,
+			       <&dmamux1 36 0x400 0x1>;
+			dma-names = "rx", "tx";
+			st,syscfg-fmp = <&syscfg 0x4 0x2>;
+			i2c-analog-filter;
+			status = "disabled";
+		};
+
+		spi1: spi@44004000 {
+			compatible = "st,stm32h7-spi";
+			reg = <0x44004000 0x400>;
+			interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc SPI1_K>;
+			resets = <&rcc SPI1_R>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			dmas = <&dmamux1 37 0x400 0x01>,
+			       <&dmamux1 38 0x400 0x01>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		dma1: dma-controller@48000000 {
+			compatible = "st,stm32-dma";
+			reg = <0x48000000 0x400>;
+			interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc DMA1>;
+			resets = <&rcc DMA1_R>;
+			#dma-cells = <4>;
+			st,mem2mem;
+			dma-requests = <8>;
+		};
+
+		dma2: dma-controller@48001000 {
+			compatible = "st,stm32-dma";
+			reg = <0x48001000 0x400>;
+			interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc DMA2>;
+			resets = <&rcc DMA2_R>;
+			#dma-cells = <4>;
+			st,mem2mem;
+			dma-requests = <8>;
+		};
+
+		dmamux1: dma-router@48002000 {
+			compatible = "st,stm32h7-dmamux";
+			reg = <0x48002000 0x40>;
+			clocks = <&rcc DMAMUX1>;
+			resets = <&rcc DMAMUX1_R>;
+			#dma-cells = <3>;
+			dma-masters = <&dma1 &dma2>;
+			dma-requests = <128>;
+			dma-channels = <16>;
+		};
+
+		spi4: spi@4c002000 {
+			compatible = "st,stm32h7-spi";
+			reg = <0x4c002000 0x400>;
+			interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc SPI4_K>;
+			resets = <&rcc SPI4_R>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			dmas = <&dmamux1 83 0x400 0x01>,
+			       <&dmamux1 84 0x400 0x01>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		spi5: spi@4c003000 {
+			compatible = "st,stm32h7-spi";
+			reg = <0x4c003000 0x400>;
+			interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc SPI5_K>;
+			resets = <&rcc SPI5_R>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			dmas = <&dmamux1 85 0x400 0x01>,
+			       <&dmamux1 86 0x400 0x01>;
+			dma-names = "rx", "tx";
+			status = "disabled";
+		};
+
+		i2c3: i2c@4c004000 {
+			compatible = "st,stm32mp13-i2c";
+			reg = <0x4c004000 0x400>;
+			interrupt-names = "event", "error";
+			interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc I2C3_K>;
+			resets = <&rcc I2C3_R>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			dmas = <&dmamux1 73 0x400 0x1>,
+			       <&dmamux1 74 0x400 0x1>;
+			dma-names = "rx", "tx";
+			st,syscfg-fmp = <&syscfg 0x4 0x4>;
+			i2c-analog-filter;
+			status = "disabled";
+		};
+
+		i2c4: i2c@4c005000 {
+			compatible = "st,stm32mp13-i2c";
+			reg = <0x4c005000 0x400>;
+			interrupt-names = "event", "error";
+			interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc I2C4_K>;
+			resets = <&rcc I2C4_R>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			dmas = <&dmamux1 75 0x400 0x1>,
+			       <&dmamux1 76 0x400 0x1>;
+			dma-names = "rx", "tx";
+			st,syscfg-fmp = <&syscfg 0x4 0x8>;
+			i2c-analog-filter;
+			status = "disabled";
+		};
+
+		i2c5: i2c@4c006000 {
+			compatible = "st,stm32mp13-i2c";
+			reg = <0x4c006000 0x400>;
+			interrupt-names = "event", "error";
+			interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc I2C5_K>;
+			resets = <&rcc I2C5_R>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			dmas = <&dmamux1 115 0x400 0x1>,
+			       <&dmamux1 116 0x400 0x1>;
+			dma-names = "rx", "tx";
+			st,syscfg-fmp = <&syscfg 0x4 0x10>;
+			i2c-analog-filter;
+			status = "disabled";
+		};
+
+		rcc: rcc@50000000 {
+			compatible = "st,stm32mp13-rcc", "syscon";
+			reg = <0x50000000 0x1000>;
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+			clock-names = "hse", "hsi", "csi", "lse", "lsi";
+			clocks = <&scmi_clk CK_SCMI_HSE>,
+				 <&scmi_clk CK_SCMI_HSI>,
+				 <&scmi_clk CK_SCMI_CSI>,
+				 <&scmi_clk CK_SCMI_LSE>,
+				 <&scmi_clk CK_SCMI_LSI>;
+		};
+
+		exti: interrupt-controller@5000d000 {
+			compatible = "st,stm32mp13-exti", "syscon";
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			reg = <0x5000d000 0x400>;
+		};
+
 		syscfg: syscon@50020000 {
 			compatible = "st,stm32mp157-syscfg", "syscon";
 			reg = <0x50020000 0x400>;
-			clocks = <&clk_pclk3>;
+			clocks = <&rcc SYSCFG>;
+		};
+
+		mdma: dma-controller@58000000 {
+			compatible = "st,stm32h7-mdma";
+			reg = <0x58000000 0x1000>;
+			interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rcc MDMA>;
+			#dma-cells = <5>;
+			dma-channels = <32>;
+			dma-requests = <48>;
 		};
 
 		sdmmc1: mmc@58005000 {
-			compatible = "arm,pl18x", "arm,primecell";
-			arm,primecell-periphid = <0x00253180>;
+			compatible = "st,stm32-sdmmc2", "arm,pl18x", "arm,primecell";
+			arm,primecell-periphid = <0x20253180>;
 			reg = <0x58005000 0x1000>, <0x58006000 0x1000>;
 			interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "cmd_irq";
-			clocks = <&clk_pll4_p>;
+			clocks = <&rcc SDMMC1_K>;
 			clock-names = "apb_pclk";
+			resets = <&rcc SDMMC1_R>;
 			cap-sd-highspeed;
 			cap-mmc-highspeed;
-			max-frequency = <120000000>;
+			max-frequency = <130000000>;
+			status = "disabled";
+		};
+
+		sdmmc2: mmc@58007000 {
+			compatible = "st,stm32-sdmmc2", "arm,pl18x", "arm,primecell";
+			arm,primecell-periphid = <0x20253180>;
+			reg = <0x58007000 0x1000>, <0x58008000 0x1000>;
+			interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "cmd_irq";
+			clocks = <&rcc SDMMC2_K>;
+			clock-names = "apb_pclk";
+			resets = <&rcc SDMMC2_R>;
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			max-frequency = <130000000>;
 			status = "disabled";
 		};
 
 		iwdg2: watchdog@5a002000 {
 			compatible = "st,stm32mp1-iwdg";
 			reg = <0x5a002000 0x400>;
-			clocks = <&clk_pclk4>, <&clk_lsi>;
+			clocks = <&rcc IWDG2>, <&scmi_clk CK_SCMI_LSI>;
 			clock-names = "pclk", "lsi";
 			status = "disabled";
 		};
 
+		rtc: rtc@5c004000 {
+			compatible = "st,stm32mp1-rtc";
+			reg = <0x5c004000 0x400>;
+			interrupts-extended = <&exti 19 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&scmi_clk CK_SCMI_RTCAPB>,
+				 <&scmi_clk CK_SCMI_RTC>;
+			clock-names = "pclk", "rtc_ck";
+			status = "disabled";
+		};
+
 		bsec: efuse@5c005000 {
 			compatible = "st,stm32mp15-bsec";
 			reg = <0x5c005000 0x400>;
@@ -164,11 +418,13 @@
 		 * Break node order to solve dependency probe issue between
 		 * pinctrl and exti.
 		 */
-		pinctrl: pin-controller@50002000 {
+		pinctrl: pinctrl@50002000 {
 			#address-cells = <1>;
 			#size-cells = <1>;
 			compatible = "st,stm32mp135-pinctrl";
 			ranges = <0 0x50002000 0x8400>;
+			interrupt-parent = <&exti>;
+			st,syscfg = <&exti 0x60 0xff>;
 			pins-are-numbered;
 
 			gpioa: gpio@50002000 {
@@ -177,7 +433,7 @@
 				interrupt-controller;
 				#interrupt-cells = <2>;
 				reg = <0x0 0x400>;
-				clocks = <&clk_pclk4>;
+				clocks = <&rcc GPIOA>;
 				st,bank-name = "GPIOA";
 				ngpios = <16>;
 				gpio-ranges = <&pinctrl 0 0 16>;
@@ -189,7 +445,7 @@
 				interrupt-controller;
 				#interrupt-cells = <2>;
 				reg = <0x1000 0x400>;
-				clocks = <&clk_pclk4>;
+				clocks = <&rcc GPIOB>;
 				st,bank-name = "GPIOB";
 				ngpios = <16>;
 				gpio-ranges = <&pinctrl 0 16 16>;
@@ -201,7 +457,7 @@
 				interrupt-controller;
 				#interrupt-cells = <2>;
 				reg = <0x2000 0x400>;
-				clocks = <&clk_pclk4>;
+				clocks = <&rcc GPIOC>;
 				st,bank-name = "GPIOC";
 				ngpios = <16>;
 				gpio-ranges = <&pinctrl 0 32 16>;
@@ -213,7 +469,7 @@
 				interrupt-controller;
 				#interrupt-cells = <2>;
 				reg = <0x3000 0x400>;
-				clocks = <&clk_pclk4>;
+				clocks = <&rcc GPIOD>;
 				st,bank-name = "GPIOD";
 				ngpios = <16>;
 				gpio-ranges = <&pinctrl 0 48 16>;
@@ -225,7 +481,7 @@
 				interrupt-controller;
 				#interrupt-cells = <2>;
 				reg = <0x4000 0x400>;
-				clocks = <&clk_pclk4>;
+				clocks = <&rcc GPIOE>;
 				st,bank-name = "GPIOE";
 				ngpios = <16>;
 				gpio-ranges = <&pinctrl 0 64 16>;
@@ -237,7 +493,7 @@
 				interrupt-controller;
 				#interrupt-cells = <2>;
 				reg = <0x5000 0x400>;
-				clocks = <&clk_pclk4>;
+				clocks = <&rcc GPIOF>;
 				st,bank-name = "GPIOF";
 				ngpios = <16>;
 				gpio-ranges = <&pinctrl 0 80 16>;
@@ -249,7 +505,7 @@
 				interrupt-controller;
 				#interrupt-cells = <2>;
 				reg = <0x6000 0x400>;
-				clocks = <&clk_pclk4>;
+				clocks = <&rcc GPIOG>;
 				st,bank-name = "GPIOG";
 				ngpios = <16>;
 				gpio-ranges = <&pinctrl 0 96 16>;
@@ -261,7 +517,7 @@
 				interrupt-controller;
 				#interrupt-cells = <2>;
 				reg = <0x7000 0x400>;
-				clocks = <&clk_pclk4>;
+				clocks = <&rcc GPIOH>;
 				st,bank-name = "GPIOH";
 				ngpios = <15>;
 				gpio-ranges = <&pinctrl 0 112 15>;
@@ -273,7 +529,7 @@
 				interrupt-controller;
 				#interrupt-cells = <2>;
 				reg = <0x8000 0x400>;
-				clocks = <&clk_pclk4>;
+				clocks = <&rcc GPIOI>;
 				st,bank-name = "GPIOI";
 				ngpios = <8>;
 				gpio-ranges = <&pinctrl 0 128 8>;
diff --git a/arch/arm/boot/dts/stm32mp133.dtsi b/arch/arm/boot/dts/stm32mp133.dtsi
index 0fb1386257cf..531c263c9f46 100644
--- a/arch/arm/boot/dts/stm32mp133.dtsi
+++ b/arch/arm/boot/dts/stm32mp133.dtsi
@@ -15,7 +15,7 @@
 			interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "int0", "int1";
-			clocks = <&clk_hse>, <&clk_pll4_r>;
+			clocks = <&scmi_clk CK_SCMI_HSE>, <&rcc FDCAN_K>;
 			clock-names = "hclk", "cclk";
 			bosch,mram-cfg = <0x0 0 0 32 0 0 2 2>;
 			status = "disabled";
@@ -28,7 +28,7 @@
 			interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "int0", "int1";
-			clocks = <&clk_hse>, <&clk_pll4_r>;
+			clocks = <&scmi_clk CK_SCMI_HSE>, <&rcc FDCAN_K>;
 			clock-names = "hclk", "cclk";
 			bosch,mram-cfg = <0x1400 0 0 32 0 0 2 2>;
 			status = "disabled";
diff --git a/arch/arm/boot/dts/stm32mp135f-dk.dts b/arch/arm/boot/dts/stm32mp135f-dk.dts
index 7e96d9e36217..de341d17e87d 100644
--- a/arch/arm/boot/dts/stm32mp135f-dk.dts
+++ b/arch/arm/boot/dts/stm32mp135f-dk.dts
@@ -6,6 +6,9 @@
 
 /dts-v1/;
 
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
 #include "stm32mp135.dtsi"
 #include "stm32mp13xf.dtsi"
 #include "stm32mp13-pinctrl.dtsi"
@@ -23,6 +26,39 @@
 		reg = <0xc0000000 0x20000000>;
 	};
 
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		optee@dd000000 {
+			reg = <0xdd000000 0x3000000>;
+			no-map;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		user-pa13 {
+			label = "User-PA13";
+			linux,code = <BTN_1>;
+			gpios = <&gpioa 13 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-blue {
+			function = LED_FUNCTION_HEARTBEAT;
+			color = <LED_COLOR_ID_BLUE>;
+			gpios = <&gpioa 14 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "heartbeat";
+			default-state = "off";
+		};
+	};
+
 	vdd_sd: vdd-sd {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd_sd";
@@ -32,15 +68,46 @@
 	};
 };
 
+&i2c1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c1_pins_a>;
+	pinctrl-1 = <&i2c1_sleep_pins_a>;
+	i2c-scl-rising-time-ns = <96>;
+	i2c-scl-falling-time-ns = <3>;
+	clock-frequency = <1000000>;
+	status = "okay";
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+};
+
+&i2c5 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c5_pins_a>;
+	pinctrl-1 = <&i2c5_sleep_pins_a>;
+	i2c-scl-rising-time-ns = <170>;
+	i2c-scl-falling-time-ns = <5>;
+	clock-frequency = <400000>;
+	status = "okay";
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+};
+
 &iwdg2 {
 	timeout-sec = <32>;
 	status = "okay";
 };
 
+&rtc {
+	status = "okay";
+};
+
 &sdmmc1 {
-	pinctrl-names = "default", "opendrain";
-	pinctrl-0 = <&sdmmc1_b4_pins_a>;
-	pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_clk_pins_a>;
+	pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_clk_pins_a>;
+	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
 	broken-cd;
 	disable-wp;
 	st,neg-edge;
@@ -49,6 +116,13 @@
 	status = "okay";
 };
 
+&spi5 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&spi5_pins_a>;
+	pinctrl-1 = <&spi5_sleep_pins_a>;
+	status = "disabled";
+};
+
 &uart4 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart4_pins_a>;
diff --git a/arch/arm/boot/dts/stm32mp13xc.dtsi b/arch/arm/boot/dts/stm32mp13xc.dtsi
index fa6889e30591..4d00e7592882 100644
--- a/arch/arm/boot/dts/stm32mp13xc.dtsi
+++ b/arch/arm/boot/dts/stm32mp13xc.dtsi
@@ -10,7 +10,8 @@
 			compatible = "st,stm32mp1-cryp";
 			reg = <0x54002000 0x400>;
 			interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&clk_axi>;
+			clocks = <&rcc CRYP1>;
+			resets = <&rcc CRYP1_R>;
 			status = "disabled";
 		};
 	};
diff --git a/arch/arm/boot/dts/stm32mp13xf.dtsi b/arch/arm/boot/dts/stm32mp13xf.dtsi
index fa6889e30591..4d00e7592882 100644
--- a/arch/arm/boot/dts/stm32mp13xf.dtsi
+++ b/arch/arm/boot/dts/stm32mp13xf.dtsi
@@ -10,7 +10,8 @@
 			compatible = "st,stm32mp1-cryp";
 			reg = <0x54002000 0x400>;
 			interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&clk_axi>;
+			clocks = <&rcc CRYP1>;
+			resets = <&rcc CRYP1_R>;
 			status = "disabled";
 		};
 	};
diff --git a/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi b/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi
index 2ebafe27a865..a9d2bec99014 100644
--- a/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi
+++ b/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi
@@ -151,6 +151,43 @@
 		};
 	};
 
+	dcmi_pins_c: dcmi-2 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 4,  AF13)>,/* DCMI_HSYNC */
+				 <STM32_PINMUX('B', 7,  AF13)>,/* DCMI_VSYNC */
+				 <STM32_PINMUX('A', 6,  AF13)>,/* DCMI_PIXCLK */
+				 <STM32_PINMUX('A', 9,  AF13)>,/* DCMI_D0 */
+				 <STM32_PINMUX('H', 10, AF13)>,/* DCMI_D1 */
+				 <STM32_PINMUX('E', 0, AF13)>,/* DCMI_D2 */
+				 <STM32_PINMUX('E', 1, AF13)>,/* DCMI_D3 */
+				 <STM32_PINMUX('H', 14, AF13)>,/* DCMI_D4 */
+				 <STM32_PINMUX('I', 4,  AF13)>,/* DCMI_D5 */
+				 <STM32_PINMUX('I', 6,  AF13)>,/* DCMI_D6 */
+				 <STM32_PINMUX('E', 6,  AF13)>,/* DCMI_D7 */
+				 <STM32_PINMUX('I', 1,  AF13)>,/* DCMI_D8 */
+				 <STM32_PINMUX('H', 7,  AF13)>;/* DCMI_D9 */
+			bias-pull-up;
+		};
+	};
+
+	dcmi_sleep_pins_c: dcmi-sleep-2 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 4,  ANALOG)>,/* DCMI_HSYNC */
+				 <STM32_PINMUX('B', 7,  ANALOG)>,/* DCMI_VSYNC */
+				 <STM32_PINMUX('A', 6,  ANALOG)>,/* DCMI_PIXCLK */
+				 <STM32_PINMUX('A', 9,  ANALOG)>,/* DCMI_D0 */
+				 <STM32_PINMUX('H', 10, ANALOG)>,/* DCMI_D1 */
+				 <STM32_PINMUX('E', 0, ANALOG)>,/* DCMI_D2 */
+				 <STM32_PINMUX('E', 1, ANALOG)>,/* DCMI_D3 */
+				 <STM32_PINMUX('H', 14, ANALOG)>,/* DCMI_D4 */
+				 <STM32_PINMUX('I', 4,  ANALOG)>,/* DCMI_D5 */
+				 <STM32_PINMUX('I', 6,  ANALOG)>,/* DCMI_D6 */
+				 <STM32_PINMUX('E', 6,  ANALOG)>,/* DCMI_D7 */
+				 <STM32_PINMUX('I', 1,  ANALOG)>,/* DCMI_D8 */
+				 <STM32_PINMUX('H', 7,  ANALOG)>;/* DCMI_D9 */
+		};
+	};
+
 	ethernet0_rgmii_pins_a: rgmii-0 {
 		pins1 {
 			pinmux = <STM32_PINMUX('G', 5, AF11)>, /* ETH_RGMII_CLK125 */
@@ -338,6 +375,81 @@
 		};
 	};
 
+	ethernet0_rmii_pins_b: rmii-1 {
+		pins1 {
+			pinmux = <STM32_PINMUX('B', 5, AF0)>, /* ETH1_CLK */
+				<STM32_PINMUX('C', 1, AF11)>, /* ETH1_MDC */
+				<STM32_PINMUX('G', 13, AF11)>, /* ETH1_TXD0 */
+				<STM32_PINMUX('G', 14, AF11)>; /* ETH1_TXD1 */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <1>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('A', 2, AF11)>; /* ETH1_MDIO */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins3 {
+			pinmux = <STM32_PINMUX('A', 7, AF11)>, /* ETH1_CRS_DV */
+				<STM32_PINMUX('C', 4, AF11)>, /* ETH1_RXD0 */
+				<STM32_PINMUX('C', 5, AF11)>; /* ETH1_RXD1 */
+			bias-disable;
+		};
+		pins4 {
+			pinmux = <STM32_PINMUX('B', 11, AF11)>; /* ETH1_TX_EN */
+		};
+	};
+
+	ethernet0_rmii_sleep_pins_b: rmii-sleep-1 {
+		pins1 {
+			pinmux = <STM32_PINMUX('A', 2, ANALOG)>, /* ETH1_MDIO */
+				<STM32_PINMUX('A', 7, ANALOG)>, /* ETH1_CRS_DV */
+				<STM32_PINMUX('B', 5, ANALOG)>, /* ETH1_CLK */
+				<STM32_PINMUX('B', 11, ANALOG)>, /* ETH1_TX_EN */
+				<STM32_PINMUX('C', 1, ANALOG)>, /* ETH1_MDC */
+				<STM32_PINMUX('C', 4, ANALOG)>, /* ETH1_RXD0 */
+				<STM32_PINMUX('C', 5, ANALOG)>, /* ETH1_RXD1 */
+				<STM32_PINMUX('G', 13, ANALOG)>, /* ETH1_TXD0 */
+				<STM32_PINMUX('G', 14, ANALOG)>; /* ETH1_TXD1 */
+		};
+	};
+
+	ethernet0_rmii_pins_c: rmii-2 {
+		pins1 {
+			pinmux = <STM32_PINMUX('G', 13, AF11)>, /* ETH1_RMII_TXD0 */
+				 <STM32_PINMUX('G', 14, AF11)>, /* ETH1_RMII_TXD1 */
+				 <STM32_PINMUX('B', 11, AF11)>, /* ETH1_RMII_TX_EN */
+				 <STM32_PINMUX('A', 1, AF11)>,  /* ETH1_RMII_REF_CLK */
+				 <STM32_PINMUX('A', 2, AF11)>,  /* ETH1_MDIO */
+				 <STM32_PINMUX('C', 1, AF11)>;  /* ETH1_MDC */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <2>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('C', 4, AF11)>,  /* ETH1_RMII_RXD0 */
+				 <STM32_PINMUX('C', 5, AF11)>,  /* ETH1_RMII_RXD1 */
+				 <STM32_PINMUX('A', 7, AF11)>;  /* ETH1_RMII_CRS_DV */
+			bias-disable;
+		};
+	};
+
+	ethernet0_rmii_sleep_pins_c: rmii-sleep-2 {
+		pins1 {
+			pinmux = <STM32_PINMUX('G', 13, ANALOG)>, /* ETH1_RMII_TXD0 */
+				 <STM32_PINMUX('G', 14, ANALOG)>, /* ETH1_RMII_TXD1 */
+				 <STM32_PINMUX('B', 11, ANALOG)>, /* ETH1_RMII_TX_EN */
+				 <STM32_PINMUX('A', 2, ANALOG)>,  /* ETH1_MDIO */
+				 <STM32_PINMUX('C', 1, ANALOG)>,  /* ETH1_MDC */
+				 <STM32_PINMUX('C', 4, ANALOG)>,  /* ETH1_RMII_RXD0 */
+				 <STM32_PINMUX('C', 5, ANALOG)>,  /* ETH1_RMII_RXD1 */
+				 <STM32_PINMUX('A', 1, ANALOG)>,  /* ETH1_RMII_REF_CLK */
+				 <STM32_PINMUX('A', 7, ANALOG)>;  /* ETH1_RMII_CRS_DV */
+		};
+	};
+
 	fmc_pins_a: fmc-0 {
 		pins1 {
 			pinmux = <STM32_PINMUX('D', 4, AF12)>, /* FMC_NOE */
@@ -848,6 +960,36 @@
 		};
 	};
 
+	mco1_pins_a: mco1-0 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 13, AF2)>; /* MCO1 */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <1>;
+		};
+	};
+
+	mco1_sleep_pins_a: mco1-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 13, ANALOG)>; /* MCO1 */
+		};
+	};
+
+	mco2_pins_a: mco2-0 {
+		pins {
+			pinmux = <STM32_PINMUX('G', 2, AF1)>; /* MCO2 */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <2>;
+		};
+	};
+
+	mco2_sleep_pins_a: mco2-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('G', 2, ANALOG)>; /* MCO2 */
+		};
+	};
+
 	m_can1_pins_a: m-can1-0 {
 		pins1 {
 			pinmux = <STM32_PINMUX('H', 13, AF9)>; /* CAN1_TX */
@@ -888,6 +1030,26 @@
 		};
 	};
 
+	m_can1_pins_c: m-can1-2 {
+		pins1 {
+			pinmux = <STM32_PINMUX('H', 13, AF9)>; /* CAN1_TX */
+			slew-rate = <1>;
+			drive-push-pull;
+			bias-disable;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('H', 14, AF9)>; /* CAN1_RX */
+			bias-disable;
+		};
+	};
+
+	m_can1_sleep_pins_c: m_can1-sleep-2 {
+		pins {
+			pinmux = <STM32_PINMUX('H', 13, ANALOG)>, /* CAN1_TX */
+				 <STM32_PINMUX('H', 14, ANALOG)>; /* CAN1_RX */
+		};
+	};
+
 	m_can2_pins_a: m-can2-0 {
 		pins1 {
 			pinmux = <STM32_PINMUX('B', 13, AF9)>; /* CAN2_TX */
@@ -927,6 +1089,21 @@
 		};
 	};
 
+	pwm1_pins_b: pwm1-1 {
+		pins {
+			pinmux = <STM32_PINMUX('E', 9, AF1)>; /* TIM1_CH1 */
+			bias-pull-down;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+	};
+
+	pwm1_sleep_pins_b: pwm1-sleep-1 {
+		pins {
+			pinmux = <STM32_PINMUX('E', 9, ANALOG)>; /* TIM1_CH1 */
+		};
+	};
+
 	pwm2_pins_a: pwm2-0 {
 		pins {
 			pinmux = <STM32_PINMUX('A', 3, AF1)>; /* TIM2_CH4 */
@@ -1084,7 +1261,7 @@
 	};
 
 	qspi_bk1_pins_a: qspi-bk1-0 {
-		pins1 {
+		pins {
 			pinmux = <STM32_PINMUX('F', 8, AF10)>, /* QSPI_BK1_IO0 */
 				 <STM32_PINMUX('F', 9, AF10)>, /* QSPI_BK1_IO1 */
 				 <STM32_PINMUX('F', 7, AF9)>, /* QSPI_BK1_IO2 */
@@ -1093,12 +1270,6 @@
 			drive-push-pull;
 			slew-rate = <1>;
 		};
-		pins2 {
-			pinmux = <STM32_PINMUX('B', 6, AF10)>; /* QSPI_BK1_NCS */
-			bias-pull-up;
-			drive-push-pull;
-			slew-rate = <1>;
-		};
 	};
 
 	qspi_bk1_sleep_pins_a: qspi-bk1-sleep-0 {
@@ -1106,13 +1277,12 @@
 			pinmux = <STM32_PINMUX('F', 8, ANALOG)>, /* QSPI_BK1_IO0 */
 				 <STM32_PINMUX('F', 9, ANALOG)>, /* QSPI_BK1_IO1 */
 				 <STM32_PINMUX('F', 7, ANALOG)>, /* QSPI_BK1_IO2 */
-				 <STM32_PINMUX('F', 6, ANALOG)>, /* QSPI_BK1_IO3 */
-				 <STM32_PINMUX('B', 6, ANALOG)>; /* QSPI_BK1_NCS */
+				 <STM32_PINMUX('F', 6, ANALOG)>; /* QSPI_BK1_IO3 */
 		};
 	};
 
 	qspi_bk2_pins_a: qspi-bk2-0 {
-		pins1 {
+		pins {
 			pinmux = <STM32_PINMUX('H', 2, AF9)>, /* QSPI_BK2_IO0 */
 				 <STM32_PINMUX('H', 3, AF9)>, /* QSPI_BK2_IO1 */
 				 <STM32_PINMUX('G', 10, AF11)>, /* QSPI_BK2_IO2 */
@@ -1121,7 +1291,34 @@
 			drive-push-pull;
 			slew-rate = <1>;
 		};
-		pins2 {
+	};
+
+	qspi_bk2_sleep_pins_a: qspi-bk2-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('H', 2, ANALOG)>, /* QSPI_BK2_IO0 */
+				 <STM32_PINMUX('H', 3, ANALOG)>, /* QSPI_BK2_IO1 */
+				 <STM32_PINMUX('G', 10, ANALOG)>, /* QSPI_BK2_IO2 */
+				 <STM32_PINMUX('G', 7, ANALOG)>; /* QSPI_BK2_IO3 */
+		};
+	};
+
+	qspi_cs1_pins_a: qspi-cs1-0 {
+		pins {
+			pinmux = <STM32_PINMUX('B', 6, AF10)>; /* QSPI_BK1_NCS */
+			bias-pull-up;
+			drive-push-pull;
+			slew-rate = <1>;
+		};
+	};
+
+	qspi_cs1_sleep_pins_a: qspi-cs1-sleep-0 {
+		pins {
+			pinmux = <STM32_PINMUX('B', 6, ANALOG)>; /* QSPI_BK1_NCS */
+		};
+	};
+
+	qspi_cs2_pins_a: qspi-cs2-0 {
+		pins {
 			pinmux = <STM32_PINMUX('C', 0, AF10)>; /* QSPI_BK2_NCS */
 			bias-pull-up;
 			drive-push-pull;
@@ -1129,13 +1326,9 @@
 		};
 	};
 
-	qspi_bk2_sleep_pins_a: qspi-bk2-sleep-0 {
+	qspi_cs2_sleep_pins_a: qspi-cs2-sleep-0 {
 		pins {
-			pinmux = <STM32_PINMUX('H', 2, ANALOG)>, /* QSPI_BK2_IO0 */
-				 <STM32_PINMUX('H', 3, ANALOG)>, /* QSPI_BK2_IO1 */
-				 <STM32_PINMUX('G', 10, ANALOG)>, /* QSPI_BK2_IO2 */
-				 <STM32_PINMUX('G', 7, ANALOG)>, /* QSPI_BK2_IO3 */
-				 <STM32_PINMUX('C', 0, ANALOG)>; /* QSPI_BK2_NCS */
+			pinmux = <STM32_PINMUX('C', 0, ANALOG)>; /* QSPI_BK2_NCS */
 		};
 	};
 
@@ -1190,7 +1383,7 @@
 		};
 	};
 
-	sai2a_sleep_pins_c: sai2a-2 {
+	sai2a_sleep_pins_c: sai2a-sleep-2 {
 		pins {
 			pinmux = <STM32_PINMUX('D', 13, ANALOG)>, /* SAI2_SCK_A */
 				 <STM32_PINMUX('D', 11, ANALOG)>, /* SAI2_SD_A */
@@ -1689,15 +1882,30 @@
 
 	spi2_pins_a: spi2-0 {
 		pins1 {
-			pinmux = <STM32_PINMUX('B', 10, AF5)>, /* SPI1_SCK */
-				 <STM32_PINMUX('I', 3, AF5)>; /* SPI1_MOSI */
+			pinmux = <STM32_PINMUX('B', 10, AF5)>, /* SPI2_SCK */
+				 <STM32_PINMUX('I', 3, AF5)>; /* SPI2_MOSI */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <1>;
+		};
+
+		pins2 {
+			pinmux = <STM32_PINMUX('I', 2, AF5)>; /* SPI2_MISO */
+			bias-disable;
+		};
+	};
+
+	spi2_pins_b: spi2-1 {
+		pins1 {
+			pinmux = <STM32_PINMUX('I', 1, AF5)>, /* SPI2_SCK */
+				 <STM32_PINMUX('I', 3, AF5)>; /* SPI2_MOSI */
 			bias-disable;
 			drive-push-pull;
 			slew-rate = <1>;
 		};
 
 		pins2 {
-			pinmux = <STM32_PINMUX('I', 2, AF5)>; /* SPI1_MISO */
+			pinmux = <STM32_PINMUX('I', 2, AF5)>; /* SPI2_MISO */
 			bias-disable;
 		};
 	};
@@ -1718,7 +1926,7 @@
 
 	stusb1600_pins_a: stusb1600-0 {
 		pins {
-			pinmux = <STM32_PINMUX('I', 11, ANALOG)>;
+			pinmux = <STM32_PINMUX('I', 11, GPIO)>;
 			bias-pull-up;
 		};
 	};
@@ -1737,20 +1945,20 @@
 	};
 
 	uart4_idle_pins_a: uart4-idle-0 {
-		   pins1 {
-			 pinmux = <STM32_PINMUX('G', 11, ANALOG)>; /* UART4_TX */
-		   };
-		   pins2 {
-			 pinmux = <STM32_PINMUX('B', 2, AF8)>; /* UART4_RX */
-			 bias-disable;
-		   };
+		pins1 {
+			pinmux = <STM32_PINMUX('G', 11, ANALOG)>; /* UART4_TX */
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('B', 2, AF8)>; /* UART4_RX */
+			bias-disable;
+		};
 	};
 
 	uart4_sleep_pins_a: uart4-sleep-0 {
-		   pins {
+		pins {
 			pinmux = <STM32_PINMUX('G', 11, ANALOG)>, /* UART4_TX */
 				 <STM32_PINMUX('B', 2, ANALOG)>; /* UART4_RX */
-		    };
+		};
 	};
 
 	uart4_pins_b: uart4-1 {
@@ -1779,6 +1987,49 @@
 		};
 	};
 
+	uart4_pins_d: uart4-3 {
+		pins1 {
+			pinmux = <STM32_PINMUX('A', 13, AF8)>; /* UART4_TX */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('B', 2, AF8)>; /* UART4_RX */
+			bias-disable;
+		};
+	};
+
+	uart4_idle_pins_d: uart4-idle-3 {
+		pins1 {
+			pinmux = <STM32_PINMUX('A', 13, ANALOG)>; /* UART4_TX */
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('B', 2, AF8)>; /* UART4_RX */
+			bias-disable;
+		};
+	};
+
+	uart4_sleep_pins_d: uart4-sleep-3 {
+		pins {
+			pinmux = <STM32_PINMUX('A', 13, ANALOG)>, /* UART4_TX */
+				 <STM32_PINMUX('B', 2, ANALOG)>; /* UART4_RX */
+		};
+	};
+
+	uart5_pins_a: uart5-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('B', 13, AF14)>; /* UART5_TX */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('B', 5, AF12)>; /* UART5_RX */
+			bias-disable;
+		};
+	};
+
 	uart7_pins_a: uart7-0 {
 		pins1 {
 			pinmux = <STM32_PINMUX('E', 8, AF7)>; /* UART7_TX */
@@ -1816,7 +2067,7 @@
 		};
 		pins2 {
 			pinmux = <STM32_PINMUX('E', 7, AF7)>; /* UART7_RX */
-			bias-disable;
+			bias-pull-up;
 		};
 	};
 
@@ -1826,7 +2077,7 @@
 		};
 		pins2 {
 			pinmux = <STM32_PINMUX('E', 7, AF7)>; /* UART7_RX */
-			bias-disable;
+			bias-pull-up;
 		};
 	};
 
@@ -1971,7 +2222,7 @@
 		pins2 {
 			pinmux = <STM32_PINMUX('B', 12, AF8)>, /* USART3_RX */
 				 <STM32_PINMUX('I', 10, AF8)>; /* USART3_CTS_NSS */
-			bias-disable;
+			bias-pull-up;
 		};
 	};
 
@@ -1988,7 +2239,7 @@
 		};
 		pins3 {
 			pinmux = <STM32_PINMUX('B', 12, AF8)>; /* USART3_RX */
-			bias-disable;
+			bias-pull-up;
 		};
 	};
 
@@ -2012,7 +2263,7 @@
 		pins2 {
 			pinmux = <STM32_PINMUX('B', 12, AF8)>, /* USART3_RX */
 				 <STM32_PINMUX('B', 13, AF7)>; /* USART3_CTS_NSS */
-			bias-disable;
+			bias-pull-up;
 		};
 	};
 
@@ -2029,7 +2280,7 @@
 		};
 		pins3 {
 			pinmux = <STM32_PINMUX('B', 12, AF8)>; /* USART3_RX */
-			bias-disable;
+			bias-pull-up;
 		};
 	};
 
@@ -2042,6 +2293,83 @@
 		};
 	};
 
+	usart3_pins_d: usart3-3 {
+		pins1 {
+			pinmux = <STM32_PINMUX('B', 10, AF7)>, /* USART3_TX */
+				 <STM32_PINMUX('G', 8, AF8)>; /* USART3_RTS */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('D', 9, AF7)>, /* USART3_RX */
+				 <STM32_PINMUX('D', 11, AF7)>; /* USART3_CTS_NSS */
+			bias-disable;
+		};
+	};
+
+	usart3_idle_pins_d: usart3-idle-3 {
+		pins1 {
+			pinmux = <STM32_PINMUX('B', 10, ANALOG)>, /* USART3_TX */
+				 <STM32_PINMUX('G', 8, ANALOG)>, /* USART3_RTS */
+				 <STM32_PINMUX('D', 11, ANALOG)>; /* USART3_CTS_NSS */
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('D', 9, AF7)>; /* USART3_RX */
+			bias-disable;
+		};
+	};
+
+	usart3_sleep_pins_d: usart3-sleep-3 {
+		pins {
+			pinmux = <STM32_PINMUX('B', 10, ANALOG)>, /* USART3_TX */
+				 <STM32_PINMUX('G', 8, ANALOG)>, /* USART3_RTS */
+				 <STM32_PINMUX('D', 11, ANALOG)>, /* USART3_CTS_NSS */
+				 <STM32_PINMUX('D', 9, ANALOG)>; /* USART3_RX */
+		};
+	};
+
+	usart3_pins_e: usart3-4 {
+		pins1 {
+			pinmux = <STM32_PINMUX('B', 10, AF7)>, /* USART3_TX */
+				 <STM32_PINMUX('G', 8, AF8)>; /* USART3_RTS */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('B', 11, AF7)>, /* USART3_RX */
+				 <STM32_PINMUX('D', 11, AF7)>; /* USART3_CTS_NSS */
+			bias-pull-up;
+		};
+	};
+
+	usart3_idle_pins_e: usart3-idle-4 {
+		pins1 {
+			pinmux = <STM32_PINMUX('B', 10, ANALOG)>, /* USART3_TX */
+				 <STM32_PINMUX('D', 11, ANALOG)>; /* USART3_CTS_NSS */
+		};
+		pins2 {
+			pinmux = <STM32_PINMUX('G', 8, AF8)>; /* USART3_RTS */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <0>;
+		};
+		pins3 {
+			pinmux = <STM32_PINMUX('B', 11, AF7)>; /* USART3_RX */
+			bias-pull-up;
+		};
+	};
+
+	usart3_sleep_pins_e: usart3-sleep-4 {
+		pins {
+			pinmux = <STM32_PINMUX('B', 10, ANALOG)>, /* USART3_TX */
+				 <STM32_PINMUX('G', 8, ANALOG)>, /* USART3_RTS */
+				 <STM32_PINMUX('D', 11, ANALOG)>, /* USART3_CTS_NSS */
+				 <STM32_PINMUX('B', 11, ANALOG)>; /* USART3_RX */
+		};
+	};
+
 	usbotg_hs_pins_a: usbotg-hs-0 {
 		pins {
 			pinmux = <STM32_PINMUX('A', 10, ANALOG)>; /* OTG_ID */
@@ -2120,4 +2448,19 @@
 			bias-disable;
 		};
 	};
+
+	spi1_pins_b: spi1-1 {
+		pins1 {
+			pinmux = <STM32_PINMUX('A', 5, AF5)>, /* SPI1_SCK */
+				 <STM32_PINMUX('B', 5, AF5)>; /* SPI1_MOSI */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <1>;
+		};
+
+		pins2 {
+			pinmux = <STM32_PINMUX('A', 6, AF5)>; /* SPI1_MISO */
+			bias-disable;
+		};
+	};
 };
diff --git a/arch/arm/boot/dts/stm32mp15-scmi.dtsi b/arch/arm/boot/dts/stm32mp15-scmi.dtsi
new file mode 100644
index 000000000000..543f24c2f4f6
--- /dev/null
+++ b/arch/arm/boot/dts/stm32mp15-scmi.dtsi
@@ -0,0 +1,105 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2022 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@foss.st.com> for STMicroelectronics.
+ */
+
+/ {
+	firmware {
+		optee: optee {
+			compatible = "linaro,optee-tz";
+			method = "smc";
+		};
+
+		scmi: scmi {
+			compatible = "linaro,scmi-optee";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			linaro,optee-channel-id = <0>;
+			shmem = <&scmi_shm>;
+
+			scmi_clk: protocol@14 {
+				reg = <0x14>;
+				#clock-cells = <1>;
+			};
+
+			scmi_reset: protocol@16 {
+				reg = <0x16>;
+				#reset-cells = <1>;
+			};
+
+			scmi_voltd: protocol@17 {
+				reg = <0x17>;
+
+				scmi_reguls: regulators {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					scmi_reg11: reg11@0 {
+						reg = <0>;
+						regulator-name = "reg11";
+						regulator-min-microvolt = <1100000>;
+						regulator-max-microvolt = <1100000>;
+					};
+
+					scmi_reg18: reg18@1 {
+						voltd-name = "reg18";
+						reg = <1>;
+						regulator-name = "reg18";
+						regulator-min-microvolt = <1800000>;
+						regulator-max-microvolt = <1800000>;
+					};
+
+					scmi_usb33: usb33@2 {
+						reg = <2>;
+						regulator-name = "usb33";
+						regulator-min-microvolt = <3300000>;
+						regulator-max-microvolt = <3300000>;
+					};
+				};
+			};
+		};
+	};
+
+	soc {
+		scmi_sram: sram@2ffff000 {
+			compatible = "mmio-sram";
+			reg = <0x2ffff000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x2ffff000 0x1000>;
+
+			scmi_shm: scmi-sram@0 {
+				compatible = "arm,scmi-shmem";
+				reg = <0 0x80>;
+			};
+		};
+	};
+};
+
+&reg11 {
+	status = "disabled";
+};
+
+&reg18 {
+	status = "disabled";
+};
+
+&usb33 {
+	status = "disabled";
+};
+
+&usbotg_hs {
+	usb33d-supply = <&scmi_usb33>;
+};
+
+&usbphyc {
+	vdda1v1-supply = <&scmi_reg11>;
+	vdda1v8-supply = <&scmi_reg18>;
+};
+
+/delete-node/ &clk_hse;
+/delete-node/ &clk_hsi;
+/delete-node/ &clk_lse;
+/delete-node/ &clk_lsi;
+/delete-node/ &clk_csi;
diff --git a/arch/arm/boot/dts/stm32mp151.dtsi b/arch/arm/boot/dts/stm32mp151.dtsi
index 1cfc2f011e70..e02b3f5d44cb 100644
--- a/arch/arm/boot/dts/stm32mp151.dtsi
+++ b/arch/arm/boot/dts/stm32mp151.dtsi
@@ -45,10 +45,10 @@
 
 	timer {
 		compatible = "arm,armv7-timer";
-		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
-			     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
-			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
-			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>;
 		interrupt-parent = <&intc>;
 	};
 
@@ -127,6 +127,8 @@
 			#size-cells = <0>;
 			compatible = "st,stm32-timers";
 			reg = <0x40000000 0x400>;
+			interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "global";
 			clocks = <&rcc TIM2_K>;
 			clock-names = "int";
 			dmas = <&dmamux1 18 0x400 0x1>,
@@ -160,6 +162,8 @@
 			#size-cells = <0>;
 			compatible = "st,stm32-timers";
 			reg = <0x40001000 0x400>;
+			interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "global";
 			clocks = <&rcc TIM3_K>;
 			clock-names = "int";
 			dmas = <&dmamux1 23 0x400 0x1>,
@@ -194,6 +198,8 @@
 			#size-cells = <0>;
 			compatible = "st,stm32-timers";
 			reg = <0x40002000 0x400>;
+			interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "global";
 			clocks = <&rcc TIM4_K>;
 			clock-names = "int";
 			dmas = <&dmamux1 29 0x400 0x1>,
@@ -226,6 +232,8 @@
 			#size-cells = <0>;
 			compatible = "st,stm32-timers";
 			reg = <0x40003000 0x400>;
+			interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "global";
 			clocks = <&rcc TIM5_K>;
 			clock-names = "int";
 			dmas = <&dmamux1 55 0x400 0x1>,
@@ -260,6 +268,8 @@
 			#size-cells = <0>;
 			compatible = "st,stm32-timers";
 			reg = <0x40004000 0x400>;
+			interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "global";
 			clocks = <&rcc TIM6_K>;
 			clock-names = "int";
 			dmas = <&dmamux1 69 0x400 0x1>;
@@ -278,6 +288,8 @@
 			#size-cells = <0>;
 			compatible = "st,stm32-timers";
 			reg = <0x40005000 0x400>;
+			interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "global";
 			clocks = <&rcc TIM7_K>;
 			clock-names = "int";
 			dmas = <&dmamux1 70 0x400 0x1>;
@@ -296,6 +308,8 @@
 			#size-cells = <0>;
 			compatible = "st,stm32-timers";
 			reg = <0x40006000 0x400>;
+			interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "global";
 			clocks = <&rcc TIM12_K>;
 			clock-names = "int";
 			status = "disabled";
@@ -318,6 +332,8 @@
 			#size-cells = <0>;
 			compatible = "st,stm32-timers";
 			reg = <0x40007000 0x400>;
+			interrupts = <GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "global";
 			clocks = <&rcc TIM13_K>;
 			clock-names = "int";
 			status = "disabled";
@@ -340,6 +356,8 @@
 			#size-cells = <0>;
 			compatible = "st,stm32-timers";
 			reg = <0x40008000 0x400>;
+			interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "global";
 			clocks = <&rcc TIM14_K>;
 			clock-names = "int";
 			status = "disabled";
@@ -455,6 +473,9 @@
 			interrupts-extended = <&exti 27 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&rcc USART2_K>;
 			wakeup-source;
+			dmas = <&dmamux1 43 0x400 0x15>,
+			       <&dmamux1 44 0x400 0x11>;
+			dma-names = "rx", "tx";
 			status = "disabled";
 		};
 
@@ -464,6 +485,9 @@
 			interrupts-extended = <&exti 28 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&rcc USART3_K>;
 			wakeup-source;
+			dmas = <&dmamux1 45 0x400 0x15>,
+			       <&dmamux1 46 0x400 0x11>;
+			dma-names = "rx", "tx";
 			status = "disabled";
 		};
 
@@ -473,6 +497,9 @@
 			interrupts-extended = <&exti 30 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&rcc UART4_K>;
 			wakeup-source;
+			dmas = <&dmamux1 63 0x400 0x15>,
+			       <&dmamux1 64 0x400 0x11>;
+			dma-names = "rx", "tx";
 			status = "disabled";
 		};
 
@@ -482,6 +509,9 @@
 			interrupts-extended = <&exti 31 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&rcc UART5_K>;
 			wakeup-source;
+			dmas = <&dmamux1 65 0x400 0x15>,
+			       <&dmamux1 66 0x400 0x11>;
+			dma-names = "rx", "tx";
 			status = "disabled";
 		};
 
@@ -553,7 +583,7 @@
 			compatible = "st,stm32-cec";
 			reg = <0x40016000 0x400>;
 			interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&rcc CEC_K>, <&clk_lse>;
+			clocks = <&rcc CEC_K>, <&rcc CEC>;
 			clock-names = "cec", "hdmi-cec";
 			status = "disabled";
 		};
@@ -588,6 +618,9 @@
 			interrupts-extended = <&exti 32 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&rcc UART7_K>;
 			wakeup-source;
+			dmas = <&dmamux1 79 0x400 0x15>,
+			       <&dmamux1 80 0x400 0x11>;
+			dma-names = "rx", "tx";
 			status = "disabled";
 		};
 
@@ -597,6 +630,9 @@
 			interrupts-extended = <&exti 33 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&rcc UART8_K>;
 			wakeup-source;
+			dmas = <&dmamux1 81 0x400 0x15>,
+			       <&dmamux1 82 0x400 0x11>;
+			dma-names = "rx", "tx";
 			status = "disabled";
 		};
 
@@ -605,6 +641,11 @@
 			#size-cells = <0>;
 			compatible = "st,stm32-timers";
 			reg = <0x44000000 0x400>;
+			interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "brk", "up", "trg-com", "cc";
 			clocks = <&rcc TIM1_K>;
 			clock-names = "int";
 			dmas = <&dmamux1 11 0x400 0x1>,
@@ -641,6 +682,11 @@
 			#size-cells = <0>;
 			compatible = "st,stm32-timers";
 			reg = <0x44001000 0x400>;
+			interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "brk", "up", "trg-com", "cc";
 			clocks = <&rcc TIM8_K>;
 			clock-names = "int";
 			dmas = <&dmamux1 47 0x400 0x1>,
@@ -678,6 +724,9 @@
 			interrupts-extended = <&exti 29 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&rcc USART6_K>;
 			wakeup-source;
+			dmas = <&dmamux1 71 0x400 0x15>,
+			       <&dmamux1 72 0x400 0x11>;
+			dma-names = "rx", "tx";
 			status = "disabled";
 		};
 
@@ -725,6 +774,8 @@
 			#size-cells = <0>;
 			compatible = "st,stm32-timers";
 			reg = <0x44006000 0x400>;
+			interrupts = <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "global";
 			clocks = <&rcc TIM15_K>;
 			clock-names = "int";
 			dmas = <&dmamux1 105 0x400 0x1>,
@@ -752,6 +803,8 @@
 			#size-cells = <0>;
 			compatible = "st,stm32-timers";
 			reg = <0x44007000 0x400>;
+			interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "global";
 			clocks = <&rcc TIM16_K>;
 			clock-names = "int";
 			dmas = <&dmamux1 109 0x400 0x1>,
@@ -776,6 +829,8 @@
 			#size-cells = <0>;
 			compatible = "st,stm32-timers";
 			reg = <0x44008000 0x400>;
+			interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "global";
 			clocks = <&rcc TIM17_K>;
 			clock-names = "int";
 			dmas = <&dmamux1 111 0x400 0x1>,
@@ -1059,7 +1114,7 @@
 		};
 
 		sdmmc3: mmc@48004000 {
-			compatible = "arm,pl18x", "arm,primecell";
+			compatible = "st,stm32-sdmmc2", "arm,pl18x", "arm,primecell";
 			arm,primecell-periphid = <0x00253180>;
 			reg = <0x48004000 0x400>;
 			interrupts = <GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>;
@@ -1096,10 +1151,9 @@
 			reg = <0x4c001000 0x400>;
 			st,proc-id = <0>;
 			interrupts-extended =
-				<&intc GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>,
-				<&intc GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>,
-				<&exti 61 1>;
-			interrupt-names = "rx", "tx", "wakeup";
+				<&exti 61 1>,
+				<&intc GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "rx", "tx";
 			clocks = <&rcc IPCC>;
 			wakeup-source;
 			status = "disabled";
@@ -1381,7 +1435,7 @@
 		};
 
 		sdmmc1: mmc@58005000 {
-			compatible = "arm,pl18x", "arm,primecell";
+			compatible = "st,stm32-sdmmc2", "arm,pl18x", "arm,primecell";
 			arm,primecell-periphid = <0x00253180>;
 			reg = <0x58005000 0x1000>;
 			interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
@@ -1396,7 +1450,7 @@
 		};
 
 		sdmmc2: mmc@58007000 {
-			compatible = "arm,pl18x", "arm,primecell";
+			compatible = "st,stm32-sdmmc2", "arm,pl18x", "arm,primecell";
 			arm,primecell-periphid = <0x00253180>;
 			reg = <0x58007000 0x1000>;
 			interrupts = <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>;
@@ -1453,7 +1507,7 @@
 		usbh_ohci: usb@5800c000 {
 			compatible = "generic-ohci";
 			reg = <0x5800c000 0x1000>;
-			clocks = <&rcc USBH>, <&usbphyc>;
+			clocks = <&usbphyc>, <&rcc USBH>;
 			resets = <&rcc USBH_R>;
 			interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
 			status = "disabled";
@@ -1462,7 +1516,7 @@
 		usbh_ehci: usb@5800d000 {
 			compatible = "generic-ehci";
 			reg = <0x5800d000 0x1000>;
-			clocks = <&rcc USBH>;
+			clocks = <&usbphyc>, <&rcc USBH>;
 			resets = <&rcc USBH_R>;
 			interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
 			companion = <&usbh_ohci>;
@@ -1560,7 +1614,7 @@
 			reg = <0x5c004000 0x400>;
 			clocks = <&rcc RTCAPB>, <&rcc RTC>;
 			clock-names = "pclk", "rtc_ck";
-			interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts-extended = <&exti 19 IRQ_TYPE_LEVEL_HIGH>;
 			status = "disabled";
 		};
 
@@ -1602,7 +1656,7 @@
 		 * Break node order to solve dependency probe issue between
 		 * pinctrl and exti.
 		 */
-		pinctrl: pin-controller@50002000 {
+		pinctrl: pinctrl@50002000 {
 			#address-cells = <1>;
 			#size-cells = <1>;
 			compatible = "st,stm32mp157-pinctrl";
@@ -1733,7 +1787,7 @@
 			};
 		};
 
-		pinctrl_z: pin-controller-z@54004000 {
+		pinctrl_z: pinctrl@54004000 {
 			#address-cells = <1>;
 			#size-cells = <1>;
 			compatible = "st,stm32mp157-z-pinctrl";
diff --git a/arch/arm/boot/dts/stm32mp151a-prtt1a.dts b/arch/arm/boot/dts/stm32mp151a-prtt1a.dts
new file mode 100644
index 000000000000..75874eafde11
--- /dev/null
+++ b/arch/arm/boot/dts/stm32mp151a-prtt1a.dts
@@ -0,0 +1,52 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) Protonic Holland
+ * Author: David Jander <david@protonic.nl>
+ */
+/dts-v1/;
+
+#include "stm32mp151a-prtt1l.dtsi"
+
+/ {
+	model = "Protonic PRTT1A";
+	compatible = "prt,prtt1a", "st,stm32mp151";
+};
+
+&ethernet0 {
+	phy-handle = <&phy0>;
+};
+
+&mdio0 {
+	/* TI DP83TD510E */
+	phy0: ethernet-phy@0 {
+		compatible = "ethernet-phy-id2000.0181";
+		reg = <0>;
+		interrupts-extended = <&gpioa 4 IRQ_TYPE_LEVEL_LOW>;
+		reset-gpios = <&gpioa 3 GPIO_ACTIVE_LOW>;
+		reset-assert-us = <10>;
+		reset-deassert-us = <35>;
+	};
+};
+
+&pwm5_pins_a {
+	pins {
+		pinmux = <STM32_PINMUX('A', 0, AF2)>; /* TIM5_CH1 */
+	};
+};
+
+&pwm5_sleep_pins_a {
+	pins {
+		pinmux = <STM32_PINMUX('A', 0, ANALOG)>; /* TIM5_CH1 */
+	};
+};
+
+&timers5 {
+	status = "okay";
+
+	pwm {
+		pinctrl-0 = <&pwm5_pins_a>;
+		pinctrl-1 = <&pwm5_sleep_pins_a>;
+		pinctrl-names = "default", "sleep";
+		status = "okay";
+	};
+};
diff --git a/arch/arm/boot/dts/stm32mp151a-prtt1c.dts b/arch/arm/boot/dts/stm32mp151a-prtt1c.dts
new file mode 100644
index 000000000000..7ecf31263abc
--- /dev/null
+++ b/arch/arm/boot/dts/stm32mp151a-prtt1c.dts
@@ -0,0 +1,304 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) Protonic Holland
+ * Author: David Jander <david@protonic.nl>
+ */
+/dts-v1/;
+
+#include "stm32mp151a-prtt1l.dtsi"
+
+/ {
+	model = "Protonic PRTT1C";
+	compatible = "prt,prtt1c", "st,stm32mp151";
+
+	clock_ksz9031: clock-ksz9031 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <25000000>;
+	};
+
+	clock_sja1105: clock-sja1105 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <25000000>;
+	};
+
+	mdio0: mdio {
+		compatible = "virtual,mdio-gpio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpios = <&gpioc 1 GPIO_ACTIVE_HIGH
+			 &gpioa 2 GPIO_ACTIVE_HIGH>;
+
+	};
+
+	wifi_pwrseq: wifi-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&gpiod 8 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&ethernet0 {
+	fixed-link {
+		speed = <100>;
+		full-duplex;
+	};
+};
+
+&gpioa {
+	gpio-line-names =
+		"", "", "", "PHY0_nRESET", "PHY0_nINT", "", "", "",
+		"", "", "", "", "", "", "", "SPI1_nSS";
+};
+
+&gpiod {
+	gpio-line-names =
+		"", "", "", "", "", "", "", "",
+		"WFM_RESET", "", "", "", "", "", "", "";
+};
+
+&gpioe {
+	gpio-line-names =
+		"SDMMC2_nRESET", "", "", "", "", "", "SPI1_nRESET", "",
+		"", "", "", "", "WFM_nIRQ", "", "", "";
+};
+
+&gpiog {
+	gpio-line-names =
+		"", "", "", "", "", "", "", "PHY3_nINT",
+		"PHY1_nINT", "PHY3_nRESET", "PHY2_nINT", "PHY2_nRESET",
+		"PHY1_nRESET", "SPE1_PWR", "SPE0_PWR", "";
+};
+
+&mdio0 {
+	/* All this DP83TD510E PHYs can't be probed before switch@0 is
+	 * probed so we need to use compatible with PHYid
+	 */
+	/* TI DP83TD510E */
+	t1l0_phy: ethernet-phy@6 {
+		compatible = "ethernet-phy-id2000.0181";
+		reg = <6>;
+		interrupts-extended = <&gpioa 4 IRQ_TYPE_LEVEL_LOW>;
+		reset-gpios = <&gpioa 3 GPIO_ACTIVE_LOW>;
+		reset-assert-us = <10>;
+		reset-deassert-us = <35>;
+	};
+
+	/* TI DP83TD510E */
+	t1l1_phy: ethernet-phy@7 {
+		compatible = "ethernet-phy-id2000.0181";
+		reg = <7>;
+		interrupts-extended = <&gpiog 8 IRQ_TYPE_LEVEL_LOW>;
+		reset-gpios = <&gpiog 12 GPIO_ACTIVE_LOW>;
+		reset-assert-us = <10>;
+		reset-deassert-us = <35>;
+	};
+
+	/* TI DP83TD510E */
+	t1l2_phy: ethernet-phy@10 {
+		compatible = "ethernet-phy-id2000.0181";
+		reg = <10>;
+		interrupts-extended = <&gpiog 10 IRQ_TYPE_LEVEL_LOW>;
+		reset-gpios = <&gpiog 11 GPIO_ACTIVE_LOW>;
+		reset-assert-us = <10>;
+		reset-deassert-us = <35>;
+	};
+
+	/* Micrel KSZ9031 */
+	rj45_phy: ethernet-phy@2 {
+		reg = <2>;
+		interrupts-extended = <&gpiog 7 IRQ_TYPE_LEVEL_LOW>;
+		reset-gpios = <&gpiog 9 GPIO_ACTIVE_LOW>;
+		reset-assert-us = <10000>;
+		reset-deassert-us = <1000>;
+
+		clocks = <&clock_ksz9031>;
+	};
+};
+
+&qspi {
+	status = "disabled";
+};
+
+&sdmmc2 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_a>;
+	pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_a>;
+	pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_a>;
+	non-removable;
+	no-sd;
+	no-sdio;
+	no-1-8-v;
+	st,neg-edge;
+	bus-width = <8>;
+	vmmc-supply = <&reg_3v3>;
+	vqmmc-supply = <&reg_3v3>;
+	status = "okay";
+};
+
+&sdmmc2_b4_od_pins_a {
+	pins1 {
+		pinmux = <STM32_PINMUX('B', 14, AF9)>, /* SDMMC2_D0 */
+			 <STM32_PINMUX('B', 7, AF10)>, /* SDMMC2_D1 */
+			 <STM32_PINMUX('B', 3, AF9)>, /* SDMMC2_D2 */
+			 <STM32_PINMUX('B', 4, AF9)>; /* SDMMC2_D3 */
+	};
+};
+
+&sdmmc2_b4_pins_a {
+	pins1 {
+		pinmux = <STM32_PINMUX('B', 14, AF9)>, /* SDMMC2_D0 */
+			 <STM32_PINMUX('B', 7, AF10)>, /* SDMMC2_D1 */
+			 <STM32_PINMUX('B', 3, AF9)>, /* SDMMC2_D2 */
+			 <STM32_PINMUX('B', 4, AF9)>, /* SDMMC2_D3 */
+			 <STM32_PINMUX('G', 6, AF10)>; /* SDMMC2_CMD */
+	};
+};
+
+&sdmmc2_b4_sleep_pins_a {
+	pins {
+		pinmux = <STM32_PINMUX('B', 14, ANALOG)>, /* SDMMC2_D0 */
+			 <STM32_PINMUX('B', 7, ANALOG)>, /* SDMMC2_D1 */
+			 <STM32_PINMUX('B', 3, ANALOG)>, /* SDMMC2_D2 */
+			 <STM32_PINMUX('B', 4, ANALOG)>, /* SDMMC2_D3 */
+			 <STM32_PINMUX('E', 3, ANALOG)>, /* SDMMC2_CK */
+			 <STM32_PINMUX('G', 6, ANALOG)>; /* SDMMC2_CMD */
+	};
+};
+
+&sdmmc2_d47_pins_a {
+	pins {
+		pinmux = <STM32_PINMUX('A', 8, AF9)>, /* SDMMC2_D4 */
+			 <STM32_PINMUX('A', 9, AF10)>, /* SDMMC2_D5 */
+			 <STM32_PINMUX('C', 6, AF10)>, /* SDMMC2_D6 */
+			 <STM32_PINMUX('C', 7, AF10)>; /* SDMMC2_D7 */
+	};
+};
+
+&sdmmc2_d47_sleep_pins_a {
+	pins {
+		pinmux = <STM32_PINMUX('A', 8, ANALOG)>, /* SDMMC2_D4 */
+			 <STM32_PINMUX('A', 9, ANALOG)>, /* SDMMC2_D5 */
+			 <STM32_PINMUX('C', 6, ANALOG)>, /* SDMMC2_D6 */
+			 <STM32_PINMUX('D', 3, ANALOG)>; /* SDMMC2_D7 */
+	};
+};
+
+&sdmmc3 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc3_b4_pins_b>;
+	pinctrl-1 = <&sdmmc3_b4_od_pins_b>;
+	pinctrl-2 = <&sdmmc3_b4_sleep_pins_b>;
+	non-removable;
+	no-1-8-v;
+	st,neg-edge;
+	bus-width = <4>;
+	vmmc-supply = <&reg_3v3>;
+	vqmmc-supply = <&reg_3v3>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	mmc@1 {
+		compatible = "prt,prtt1c-wfm200", "silabs,wf200";
+		reg = <1>;
+	};
+};
+
+&sdmmc3_b4_od_pins_b {
+	pins1 {
+		pinmux = <STM32_PINMUX('D', 1, AF10)>, /* SDMMC3_D0 */
+			 <STM32_PINMUX('D', 4, AF10)>, /* SDMMC3_D1 */
+			 <STM32_PINMUX('D', 5, AF10)>, /* SDMMC3_D2 */
+			 <STM32_PINMUX('D', 7, AF10)>; /* SDMMC3_D3 */
+	};
+};
+
+&sdmmc3_b4_pins_b {
+	pins1 {
+		pinmux = <STM32_PINMUX('D', 1, AF10)>, /* SDMMC3_D0 */
+			 <STM32_PINMUX('D', 4, AF10)>, /* SDMMC3_D1 */
+			 <STM32_PINMUX('D', 5, AF10)>, /* SDMMC3_D2 */
+			 <STM32_PINMUX('D', 7, AF10)>, /* SDMMC3_D3 */
+			 <STM32_PINMUX('D', 0, AF10)>; /* SDMMC3_CMD */
+	};
+};
+
+&sdmmc3_b4_sleep_pins_b {
+	pins {
+		pinmux = <STM32_PINMUX('D', 1, ANALOG)>, /* SDMMC3_D0 */
+			 <STM32_PINMUX('D', 4, ANALOG)>, /* SDMMC3_D1 */
+			 <STM32_PINMUX('D', 5, ANALOG)>, /* SDMMC3_D2 */
+			 <STM32_PINMUX('D', 7, ANALOG)>, /* SDMMC3_D3 */
+			 <STM32_PINMUX('G', 15, ANALOG)>, /* SDMMC3_CK */
+			 <STM32_PINMUX('D', 0, ANALOG)>; /* SDMMC3_CMD */
+	};
+};
+
+&spi1 {
+	pinctrl-0 = <&spi1_pins_b>;
+	pinctrl-names = "default";
+	cs-gpios = <&gpioa 15 GPIO_ACTIVE_LOW>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+
+	switch@0 {
+		compatible = "nxp,sja1105q";
+		reg = <0>;
+		spi-max-frequency = <4000000>;
+		spi-rx-delay-us = <1>;
+		spi-tx-delay-us = <1>;
+		spi-cpha;
+
+		reset-gpios = <&gpioe 6 GPIO_ACTIVE_LOW>;
+
+		clocks = <&clock_sja1105>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				label = "t1l0";
+				phy-mode = "rmii";
+				phy-handle = <&t1l0_phy>;
+			};
+
+			port@1 {
+				reg = <1>;
+				label = "t1l1";
+				phy-mode = "rmii";
+				phy-handle = <&t1l1_phy>;
+			};
+
+			port@2 {
+				reg = <2>;
+				label = "t1l2";
+				phy-mode = "rmii";
+				phy-handle = <&t1l2_phy>;
+			};
+
+			port@3 {
+				reg = <3>;
+				label = "rj45";
+				phy-handle = <&rj45_phy>;
+				phy-mode = "rgmii-id";
+			};
+
+			port@4 {
+				reg = <4>;
+				label = "cpu";
+				ethernet = <&ethernet0>;
+				phy-mode = "rmii";
+
+				fixed-link {
+					speed = <100>;
+					full-duplex;
+				};
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/stm32mp151a-prtt1l.dtsi b/arch/arm/boot/dts/stm32mp151a-prtt1l.dtsi
new file mode 100644
index 000000000000..d865ab5d866b
--- /dev/null
+++ b/arch/arm/boot/dts/stm32mp151a-prtt1l.dtsi
@@ -0,0 +1,229 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) Protonic Holland
+ * Author: David Jander <david@protonic.nl>
+ */
+/dts-v1/;
+
+#include "stm32mp151.dtsi"
+#include "stm32mp15-pinctrl.dtsi"
+#include "stm32mp15xxad-pinctrl.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+	aliases {
+		ethernet0 = &ethernet0;
+		mdio-gpio0 = &mdio0;
+		serial0 = &uart4;
+	};
+
+	led-controller-0 {
+		compatible = "gpio-leds";
+
+		led-0 {
+			color = <LED_COLOR_ID_RED>;
+			function = LED_FUNCTION_INDICATOR;
+			gpios = <&gpioa 13 GPIO_ACTIVE_LOW>;
+		};
+
+		led-1 {
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_INDICATOR;
+			gpios = <&gpioa 14 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+
+	/* DP83TD510E PHYs have max MDC rate of 1.75MHz. Since we can't reduce
+	 * stmmac MDC clock without reducing system bus rate, we need to use
+	 * gpio based MDIO bus.
+	 */
+	mdio0: mdio {
+		compatible = "virtual,mdio-gpio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpios = <&gpioc 1 GPIO_ACTIVE_HIGH
+			 &gpioa 2 GPIO_ACTIVE_HIGH>;
+	};
+
+	reg_3v3: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+};
+
+&dts {
+	status = "okay";
+};
+
+&ethernet0 {
+	pinctrl-0 = <&ethernet0_rmii_pins_a>;
+	pinctrl-1 = <&ethernet0_rmii_sleep_pins_a>;
+	pinctrl-names = "default", "sleep";
+	phy-mode = "rmii";
+	status = "okay";
+};
+
+&ethernet0_rmii_pins_a {
+	pins1 {
+		pinmux = <STM32_PINMUX('B', 12, AF11)>, /* ETH1_RMII_TXD0 */
+			 <STM32_PINMUX('B', 13, AF11)>, /* ETH1_RMII_TXD1 */
+			 <STM32_PINMUX('B', 11, AF11)>; /* ETH1_RMII_TX_EN */
+	};
+	pins2 {
+		pinmux = <STM32_PINMUX('C', 4, AF11)>,  /* ETH1_RMII_RXD0 */
+			 <STM32_PINMUX('C', 5, AF11)>,  /* ETH1_RMII_RXD1 */
+			 <STM32_PINMUX('A', 1, AF11)>,  /* ETH1_RMII_REF_CLK input */
+			 <STM32_PINMUX('A', 7, AF11)>;  /* ETH1_RMII_CRS_DV */
+	};
+};
+
+&ethernet0_rmii_sleep_pins_a {
+	pins1 {
+		pinmux = <STM32_PINMUX('B', 12, ANALOG)>, /* ETH1_RMII_TXD0 */
+			 <STM32_PINMUX('B', 13, ANALOG)>, /* ETH1_RMII_TXD1 */
+			 <STM32_PINMUX('B', 11, ANALOG)>, /* ETH1_RMII_TX_EN */
+			 <STM32_PINMUX('C', 4, ANALOG)>,  /* ETH1_RMII_RXD0 */
+			 <STM32_PINMUX('C', 5, ANALOG)>,  /* ETH1_RMII_RXD1 */
+			 <STM32_PINMUX('A', 1, ANALOG)>,  /* ETH1_RMII_REF_CLK */
+			 <STM32_PINMUX('A', 7, ANALOG)>;  /* ETH1_RMII_CRS_DV */
+	};
+};
+
+&iwdg2 {
+	status = "okay";
+};
+
+&qspi {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a>;
+	pinctrl-1 = <&qspi_clk_sleep_pins_a &qspi_bk1_sleep_pins_a>;
+	reg = <0x58003000 0x1000>, <0x70000000 0x4000000>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	flash@0 {
+		compatible = "spi-nand";
+		reg = <0>;
+		spi-rx-bus-width = <4>;
+		spi-max-frequency = <104000000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+	};
+};
+
+&qspi_bk1_pins_a {
+	pins1 {
+		bias-pull-up;
+		drive-push-pull;
+		slew-rate = <1>;
+	};
+};
+
+&rng1 {
+	status = "okay";
+};
+
+&sdmmc1 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc1_b4_pins_a>;
+	pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
+	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
+	broken-cd;
+	st,neg-edge;
+	bus-width = <4>;
+	vmmc-supply = <&reg_3v3>;
+	vqmmc-supply = <&reg_3v3>;
+	status = "okay";
+};
+
+&sdmmc1_b4_od_pins_a {
+	pins1 {
+		bias-pull-up;
+	};
+	pins2 {
+		bias-pull-up;
+	};
+};
+
+&sdmmc1_b4_pins_a {
+	pins1 {
+		bias-pull-up;
+	};
+	pins2 {
+		bias-pull-up;
+	};
+};
+
+&uart4 {
+	pinctrl-names = "default", "sleep", "idle";
+	pinctrl-0 = <&uart4_pins_a>;
+	pinctrl-1 = <&uart4_sleep_pins_a>;
+	pinctrl-2 = <&uart4_idle_pins_a>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
+
+&uart4_idle_pins_a {
+	pins1 {
+		pinmux = <STM32_PINMUX('B', 9, ANALOG)>; /* UART4_TX */
+	};
+	pins2 {
+		pinmux = <STM32_PINMUX('B', 2, AF8)>; /* UART4_RX */
+		bias-pull-up;
+	};
+};
+
+&uart4_pins_a {
+	pins1 {
+		pinmux = <STM32_PINMUX('B', 9, AF8)>; /* UART4_TX */
+		bias-disable;
+		drive-push-pull;
+		slew-rate = <0>;
+	};
+	pins2 {
+		pinmux = <STM32_PINMUX('B', 2, AF8)>; /* UART4_RX */
+		bias-pull-up;
+	};
+};
+
+&uart4_sleep_pins_a {
+	pins {
+		pinmux = <STM32_PINMUX('B', 9, ANALOG)>, /* UART4_TX */
+			<STM32_PINMUX('B', 2, ANALOG)>; /* UART4_RX */
+	};
+};
+
+&usbh_ehci {
+	phys = <&usbphyc_port0>;
+	phy-names = "usb";
+	status = "okay";
+};
+
+&usbotg_hs {
+	dr_mode = "host";
+	pinctrl-0 = <&usbotg_hs_pins_a>;
+	pinctrl-names = "default";
+	phys = <&usbphyc_port1 0>;
+	phy-names = "usb2-phy";
+	status = "okay";
+};
+
+&usbphyc {
+	status = "okay";
+};
+
+&usbphyc_port0 {
+	phy-supply = <&reg_3v3>;
+};
+
+&usbphyc_port1 {
+	phy-supply = <&reg_3v3>;
+};
diff --git a/arch/arm/boot/dts/stm32mp151a-prtt1s.dts b/arch/arm/boot/dts/stm32mp151a-prtt1s.dts
new file mode 100644
index 000000000000..ad25929e64e6
--- /dev/null
+++ b/arch/arm/boot/dts/stm32mp151a-prtt1s.dts
@@ -0,0 +1,63 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) Protonic Holland
+ * Author: David Jander <david@protonic.nl>
+ */
+/dts-v1/;
+
+#include "stm32mp151a-prtt1l.dtsi"
+
+/ {
+	model = "Protonic PRTT1S";
+	compatible = "prt,prtt1s", "st,stm32mp151";
+};
+
+&ethernet0 {
+	phy-handle = <&phy0>;
+};
+
+&i2c1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c1_pins_a>;
+	pinctrl-1 = <&i2c1_sleep_pins_a>;
+	clock-frequency = <100000>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+
+	humidity-sensor@40 {
+		compatible = "ti,hdc1080";
+		reg = <0x40>;
+	};
+
+	co2-sensor@62 {
+		compatible = "sensirion,scd41";
+		reg = <0x62>;
+	};
+};
+
+&i2c1_pins_a {
+	pins {
+		pinmux = <STM32_PINMUX('D', 12, AF5)>, /* I2C1_SCL */
+			 <STM32_PINMUX('D', 13, AF5)>; /* I2C1_SDA */
+	};
+};
+
+&i2c1_sleep_pins_a {
+	pins {
+		pinmux = <STM32_PINMUX('D', 12, ANALOG)>, /* I2C1_SCL */
+			 <STM32_PINMUX('D', 13, ANALOG)>; /* I2C1_SDA */
+	};
+};
+
+&mdio0 {
+	/* TI DP83TD510E */
+	phy0: ethernet-phy@0 {
+		compatible = "ethernet-phy-id2000.0181";
+		reg = <0>;
+		interrupts-extended = <&gpioa 4 IRQ_TYPE_LEVEL_LOW>;
+		reset-gpios = <&gpioa 3 GPIO_ACTIVE_LOW>;
+		reset-assert-us = <10>;
+		reset-deassert-us = <35>;
+	};
+};
diff --git a/arch/arm/boot/dts/stm32mp153.dtsi b/arch/arm/boot/dts/stm32mp153.dtsi
index 1c1889b194cf..486084e0b80b 100644
--- a/arch/arm/boot/dts/stm32mp153.dtsi
+++ b/arch/arm/boot/dts/stm32mp153.dtsi
@@ -22,6 +22,13 @@
 		interrupt-affinity = <&cpu0>, <&cpu1>;
 	};
 
+	timer {
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>;
+	};
+
 	soc {
 		m_can1: can@4400e000 {
 			compatible = "bosch,m_can";
diff --git a/arch/arm/boot/dts/stm32mp153c-dhcor-drc-compact.dts b/arch/arm/boot/dts/stm32mp153c-dhcor-drc-compact.dts
new file mode 100644
index 000000000000..c8b9818499ea
--- /dev/null
+++ b/arch/arm/boot/dts/stm32mp153c-dhcor-drc-compact.dts
@@ -0,0 +1,30 @@
+// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause)
+/*
+ * Copyright (C) 2022 Marek Vasut <marex@denx.de>
+ *
+ * DHCOR STM32MP1 variant:
+ * DHCR-STM32MP153C-C065-R051-V33-SPI-I-01LG
+ * DHCOR PCB number: 586-100 or newer
+ * DRC Compact PCB number: 627-100 or newer
+ */
+
+/dts-v1/;
+
+#include "stm32mp153.dtsi"
+#include "stm32mp15xc.dtsi"
+#include "stm32mp15xx-dhcor-som.dtsi"
+#include "stm32mp15xx-dhcor-drc-compact.dtsi"
+
+/ {
+	model = "DH electronics STM32MP153C DHCOR DRC Compact";
+	compatible = "dh,stm32mp153c-dhcor-drc-compact",
+		     "dh,stm32mp153c-dhcor-som",
+		     "st,stm32mp153";
+};
+
+&m_can1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&m_can1_pins_c>;
+	pinctrl-1 = <&m_can1_sleep_pins_c>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/stm32mp157a-dk1-scmi.dts b/arch/arm/boot/dts/stm32mp157a-dk1-scmi.dts
new file mode 100644
index 000000000000..e539cc80bef8
--- /dev/null
+++ b/arch/arm/boot/dts/stm32mp157a-dk1-scmi.dts
@@ -0,0 +1,79 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2022 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@foss.st.com> for STMicroelectronics.
+ */
+
+/dts-v1/;
+
+#include "stm32mp157a-dk1.dts"
+#include "stm32mp15-scmi.dtsi"
+
+/ {
+	model = "STMicroelectronics STM32MP157A-DK1 SCMI Discovery Board";
+	compatible = "st,stm32mp157a-dk1-scmi", "st,stm32mp157a-dk1", "st,stm32mp157";
+
+	reserved-memory {
+		optee@de000000 {
+			reg = <0xde000000 0x2000000>;
+			no-map;
+		};
+	};
+};
+
+&cpu0 {
+	clocks = <&scmi_clk CK_SCMI_MPU>;
+};
+
+&cpu1 {
+	clocks = <&scmi_clk CK_SCMI_MPU>;
+};
+
+&dsi {
+	clocks = <&rcc DSI_K>, <&scmi_clk CK_SCMI_HSE>, <&rcc DSI_PX>;
+};
+
+&gpioz {
+	clocks = <&scmi_clk CK_SCMI_GPIOZ>;
+};
+
+&hash1 {
+	clocks = <&scmi_clk CK_SCMI_HASH1>;
+	resets = <&scmi_reset RST_SCMI_HASH1>;
+};
+
+&i2c4 {
+	clocks = <&scmi_clk CK_SCMI_I2C4>;
+	resets = <&scmi_reset RST_SCMI_I2C4>;
+};
+
+&iwdg2 {
+	clocks = <&rcc IWDG2>, <&scmi_clk CK_SCMI_LSI>;
+};
+
+&mdma1 {
+	resets = <&scmi_reset RST_SCMI_MDMA>;
+};
+
+&mlahb {
+	resets = <&scmi_reset RST_SCMI_MCU>;
+};
+
+&rcc {
+	compatible = "st,stm32mp1-rcc-secure", "syscon";
+	clock-names = "hse", "hsi", "csi", "lse", "lsi";
+	clocks = <&scmi_clk CK_SCMI_HSE>,
+		 <&scmi_clk CK_SCMI_HSI>,
+		 <&scmi_clk CK_SCMI_CSI>,
+		 <&scmi_clk CK_SCMI_LSE>,
+		 <&scmi_clk CK_SCMI_LSI>;
+};
+
+&rng1 {
+	clocks = <&scmi_clk CK_SCMI_RNG1>;
+	resets = <&scmi_reset RST_SCMI_RNG1>;
+};
+
+&rtc {
+	clocks = <&scmi_clk CK_SCMI_RTCAPB>, <&scmi_clk CK_SCMI_RTC>;
+};
diff --git a/arch/arm/boot/dts/stm32mp157a-icore-stm32mp1-ctouch2-of10.dts b/arch/arm/boot/dts/stm32mp157a-icore-stm32mp1-ctouch2-of10.dts
new file mode 100644
index 000000000000..9a2a4bc7d079
--- /dev/null
+++ b/arch/arm/boot/dts/stm32mp157a-icore-stm32mp1-ctouch2-of10.dts
@@ -0,0 +1,132 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (c) STMicroelectronics 2019 - All Rights Reserved
+ * Copyright (c) 2020 Engicam srl
+ * Copyright (c) 2020 Amarula Solutions(India)
+ */
+
+/dts-v1/;
+#include "stm32mp157.dtsi"
+#include "stm32mp157a-icore-stm32mp1.dtsi"
+#include "stm32mp15-pinctrl.dtsi"
+#include "stm32mp15xxaa-pinctrl.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "Engicam i.Core STM32MP1 C.TOUCH 2.0 10.1\" Open Frame";
+	compatible = "engicam,icore-stm32mp1-ctouch2-of10",
+		     "engicam,icore-stm32mp1", "st,stm32mp157";
+
+	aliases {
+		serial0 = &uart4;
+	};
+
+	backlight: backlight {
+		compatible = "gpio-backlight";
+		gpios = <&gpiod 13 GPIO_ACTIVE_HIGH>;
+		default-on;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	panel {
+		compatible = "ampire,am-1280800n3tzqw-t00h";
+		backlight = <&backlight>;
+		power-supply = <&v3v3>;
+
+		port {
+			panel_in_lvds: endpoint {
+				remote-endpoint = <&bridge_out>;
+			};
+		};
+	};
+};
+
+&dsi {
+	status = "okay";
+	phy-dsi-supply = <&reg18>;
+
+	ports {
+		port@0 {
+			reg = <0>;
+			dsi_in: endpoint {
+				remote-endpoint = <&ltdc_ep0_out>;
+			};
+		};
+
+		port@1 {
+			reg = <1>;
+			dsi_out: endpoint {
+				remote-endpoint = <&bridge_in>;
+			};
+		};
+	};
+};
+
+&i2c6 {
+	i2c-scl-falling-time-ns = <20>;
+	i2c-scl-rising-time-ns = <185>;
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c6_pins_a>;
+	pinctrl-1 = <&i2c6_sleep_pins_a>;
+	status = "okay";
+
+	bridge@2c {
+		compatible = "ti,sn65dsi84";
+		reg = <0x2c>;
+		enable-gpios = <&gpiof 15 GPIO_ACTIVE_HIGH>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				bridge_in: endpoint {
+					remote-endpoint = <&dsi_out>;
+					data-lanes = <1 2>;
+				};
+			};
+
+			port@2 {
+				reg = <2>;
+				bridge_out: endpoint {
+					remote-endpoint = <&panel_in_lvds>;
+				};
+			};
+		};
+	};
+};
+
+&ltdc {
+	status = "okay";
+
+	port {
+		ltdc_ep0_out: endpoint@0 {
+			reg = <0>;
+			remote-endpoint = <&dsi_in>;
+		};
+	};
+};
+
+&sdmmc1 {
+	bus-width = <4>;
+	disable-wp;
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc1_b4_pins_a>;
+	pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
+	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
+	st,neg-edge;
+	vmmc-supply = <&v3v3>;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default", "sleep", "idle";
+	pinctrl-0 = <&uart4_pins_a>;
+	pinctrl-1 = <&uart4_sleep_pins_a>;
+	pinctrl-2 = <&uart4_idle_pins_a>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/stm32mp157a-icore-stm32mp1-ctouch2.dts b/arch/arm/boot/dts/stm32mp157a-icore-stm32mp1-ctouch2.dts
index d3058a036c74..60ce4425a7fd 100644
--- a/arch/arm/boot/dts/stm32mp157a-icore-stm32mp1-ctouch2.dts
+++ b/arch/arm/boot/dts/stm32mp157a-icore-stm32mp1-ctouch2.dts
@@ -2,7 +2,7 @@
 /*
  * Copyright (c) STMicroelectronics 2019 - All Rights Reserved
  * Copyright (c) 2020 Engicam srl
- * Copyright (c) 2020 Amarula Solutons(India)
+ * Copyright (c) 2020 Amarula Solutions(India)
  */
 
 /dts-v1/;
@@ -43,5 +43,7 @@
 	pinctrl-0 = <&uart4_pins_a>;
 	pinctrl-1 = <&uart4_sleep_pins_a>;
 	pinctrl-2 = <&uart4_idle_pins_a>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/stm32mp157a-icore-stm32mp1-edimm2.2.dts b/arch/arm/boot/dts/stm32mp157a-icore-stm32mp1-edimm2.2.dts
index ec9f1d1cd50f..390ee8c05754 100644
--- a/arch/arm/boot/dts/stm32mp157a-icore-stm32mp1-edimm2.2.dts
+++ b/arch/arm/boot/dts/stm32mp157a-icore-stm32mp1-edimm2.2.dts
@@ -2,7 +2,7 @@
 /*
  * Copyright (c) STMicroelectronics 2019 - All Rights Reserved
  * Copyright (c) 2020 Engicam srl
- * Copyright (c) 2020 Amarula Solutons(India)
+ * Copyright (c) 2020 Amarula Solutions(India)
  */
 
 /dts-v1/;
@@ -24,6 +24,91 @@
 	chosen {
 		stdout-path = "serial0:115200n8";
 	};
+
+	backlight: backlight {
+		compatible = "gpio-backlight";
+		gpios = <&gpiod 13 GPIO_ACTIVE_HIGH>;
+		default-on;
+	};
+
+	panel {
+		compatible = "yes-optoelectronics,ytc700tlag-05-201c";
+		backlight = <&backlight>;
+		power-supply = <&v3v3>;
+
+		port {
+			panel_out_bridge: endpoint {
+				remote-endpoint = <&bridge_out_panel>;
+			};
+		};
+	};
+};
+
+&dsi {
+	status = "okay";
+	phy-dsi-supply = <&reg18>;
+
+	ports {
+		port@0 {
+			reg = <0>;
+			dsi_in_ltdc: endpoint {
+				remote-endpoint = <&ltdc_out_dsi>;
+			};
+		};
+
+		port@1 {
+			reg = <1>;
+			dsi_out_bridge: endpoint {
+				remote-endpoint = <&bridge_in_dsi>;
+			};
+		};
+	};
+};
+
+&i2c6 {
+	i2c-scl-falling-time-ns = <20>;
+	i2c-scl-rising-time-ns = <185>;
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c6_pins_a>;
+	pinctrl-1 = <&i2c6_sleep_pins_a>;
+	status = "okay";
+
+	bridge@2c {
+		compatible = "ti,sn65dsi84";
+		reg = <0x2c>;
+		enable-gpios = <&gpiof 15 GPIO_ACTIVE_HIGH>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				bridge_in_dsi: endpoint {
+					remote-endpoint = <&dsi_out_bridge>;
+					data-lanes = <1 2>;
+				};
+			};
+
+			port@2 {
+				reg = <2>;
+				bridge_out_panel: endpoint {
+					remote-endpoint = <&panel_out_bridge>;
+				};
+			};
+		};
+	};
+};
+
+&ltdc {
+	status = "okay";
+
+	port {
+		ltdc_out_dsi: endpoint@0 {
+			reg = <0>;
+			remote-endpoint = <&dsi_in_ltdc>;
+		};
+	};
 };
 
 &sdmmc1 {
@@ -43,5 +128,7 @@
 	pinctrl-0 = <&uart4_pins_a>;
 	pinctrl-1 = <&uart4_sleep_pins_a>;
 	pinctrl-2 = <&uart4_idle_pins_a>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/stm32mp157a-icore-stm32mp1.dtsi b/arch/arm/boot/dts/stm32mp157a-icore-stm32mp1.dtsi
index 01166ccacf2b..9de893101b40 100644
--- a/arch/arm/boot/dts/stm32mp157a-icore-stm32mp1.dtsi
+++ b/arch/arm/boot/dts/stm32mp157a-icore-stm32mp1.dtsi
@@ -2,7 +2,7 @@
 /*
  * Copyright (c) STMicroelectronics 2019 - All Rights Reserved
  * Copyright (c) 2020 Engicam srl
- * Copyright (c) 2020 Amarula Solutons(India)
+ * Copyright (c) 2020 Amarula Solutions(India)
  */
 
 / {
diff --git a/arch/arm/boot/dts/stm32mp157a-iot-box.dts b/arch/arm/boot/dts/stm32mp157a-iot-box.dts
index 70f394b4d3c0..6a5a4af25bd9 100644
--- a/arch/arm/boot/dts/stm32mp157a-iot-box.dts
+++ b/arch/arm/boot/dts/stm32mp157a-iot-box.dts
@@ -58,6 +58,8 @@
 	/delete-property/st,hw-flow-ctrl;
 	cts-gpios = <&gpioa 15 GPIO_ACTIVE_LOW>;
 	rts-gpios = <&gpiob 0 GPIO_ACTIVE_LOW>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
 	status = "okay";
 
 	bluetooth {
diff --git a/arch/arm/boot/dts/stm32mp157a-microgea-stm32mp1-microdev2.0-of7.dts b/arch/arm/boot/dts/stm32mp157a-microgea-stm32mp1-microdev2.0-of7.dts
index 5670b23812a2..0d7560ba2950 100644
--- a/arch/arm/boot/dts/stm32mp157a-microgea-stm32mp1-microdev2.0-of7.dts
+++ b/arch/arm/boot/dts/stm32mp157a-microgea-stm32mp1-microdev2.0-of7.dts
@@ -2,7 +2,7 @@
 /*
  * Copyright (c) STMicroelectronics 2019 - All Rights Reserved
  * Copyright (c) 2020 Engicam srl
- * Copyright (c) 2020 Amarula Solutons(India)
+ * Copyright (c) 2020 Amarula Solutions(India)
  */
 
 /dts-v1/;
@@ -143,6 +143,8 @@
 	pinctrl-0 = <&uart4_pins_a>;
 	pinctrl-1 = <&uart4_sleep_pins_a>;
 	pinctrl-2 = <&uart4_idle_pins_a>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
 	status = "okay";
 };
 
@@ -150,5 +152,7 @@
 &uart8 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart8_pins_a>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/stm32mp157a-microgea-stm32mp1-microdev2.0.dts b/arch/arm/boot/dts/stm32mp157a-microgea-stm32mp1-microdev2.0.dts
index 7a75868164dc..d949559be020 100644
--- a/arch/arm/boot/dts/stm32mp157a-microgea-stm32mp1-microdev2.0.dts
+++ b/arch/arm/boot/dts/stm32mp157a-microgea-stm32mp1-microdev2.0.dts
@@ -2,7 +2,7 @@
 /*
  * Copyright (c) STMicroelectronics 2019 - All Rights Reserved
  * Copyright (c) 2020 Engicam srl
- * Copyright (c) 2020 Amarula Solutons(India)
+ * Copyright (c) 2020 Amarula Solutions(India)
  */
 
 /dts-v1/;
@@ -44,6 +44,8 @@
 	pinctrl-0 = <&uart4_pins_a>;
 	pinctrl-1 = <&uart4_sleep_pins_a>;
 	pinctrl-2 = <&uart4_idle_pins_a>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
 	status = "okay";
 };
 
@@ -51,5 +53,7 @@
 &uart8 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart8_pins_a>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/stm32mp157a-microgea-stm32mp1.dtsi b/arch/arm/boot/dts/stm32mp157a-microgea-stm32mp1.dtsi
index 0b85175f151e..fb4600a59869 100644
--- a/arch/arm/boot/dts/stm32mp157a-microgea-stm32mp1.dtsi
+++ b/arch/arm/boot/dts/stm32mp157a-microgea-stm32mp1.dtsi
@@ -2,7 +2,7 @@
 /*
  * Copyright (c) STMicroelectronics 2019 - All Rights Reserved
  * Copyright (c) 2020 Engicam srl
- * Copyright (c) 2020 Amarula Solutons(India)
+ * Copyright (c) 2020 Amarula Solutions(India)
  */
 
 / {
diff --git a/arch/arm/boot/dts/stm32mp157a-stinger96.dtsi b/arch/arm/boot/dts/stm32mp157a-stinger96.dtsi
index a4b14ef3caee..3a36f7fe0a2c 100644
--- a/arch/arm/boot/dts/stm32mp157a-stinger96.dtsi
+++ b/arch/arm/boot/dts/stm32mp157a-stinger96.dtsi
@@ -288,6 +288,8 @@
 	pinctrl-0 = <&usart2_pins_b>;
 	pinctrl-1 = <&usart2_sleep_pins_b>;
 	st,hw-flow-ctrl;
+	/delete-property/dmas;
+	/delete-property/dma-names;
 	status = "okay";
 };
 
@@ -296,6 +298,8 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart4_pins_c>;
 	st,hw-flow-ctrl;
+	/delete-property/dmas;
+	/delete-property/dma-names;
 	status = "okay";
 };
 
@@ -303,6 +307,8 @@
 &uart7 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart7_pins_b>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
 	status = "okay";
 };
 
diff --git a/arch/arm/boot/dts/stm32mp157c-dk2-scmi.dts b/arch/arm/boot/dts/stm32mp157c-dk2-scmi.dts
new file mode 100644
index 000000000000..97e4f94b0a24
--- /dev/null
+++ b/arch/arm/boot/dts/stm32mp157c-dk2-scmi.dts
@@ -0,0 +1,85 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2022 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@foss.st.com> for STMicroelectronics.
+ */
+
+/dts-v1/;
+
+#include "stm32mp157c-dk2.dts"
+#include "stm32mp15-scmi.dtsi"
+
+/ {
+	model = "STMicroelectronics STM32MP157C-DK2 SCMI Discovery Board";
+	compatible = "st,stm32mp157c-dk2-scmi", "st,stm32mp157c-dk2", "st,stm32mp157";
+
+	reserved-memory {
+		optee@de000000 {
+			reg = <0xde000000 0x2000000>;
+			no-map;
+		};
+	};
+};
+
+&cpu0 {
+	clocks = <&scmi_clk CK_SCMI_MPU>;
+};
+
+&cpu1 {
+	clocks = <&scmi_clk CK_SCMI_MPU>;
+};
+
+&cryp1 {
+	clocks = <&scmi_clk CK_SCMI_CRYP1>;
+	resets = <&scmi_reset RST_SCMI_CRYP1>;
+};
+
+&dsi {
+	phy-dsi-supply = <&scmi_reg18>;
+	clocks = <&rcc DSI_K>, <&scmi_clk CK_SCMI_HSE>, <&rcc DSI_PX>;
+};
+
+&gpioz {
+	clocks = <&scmi_clk CK_SCMI_GPIOZ>;
+};
+
+&hash1 {
+	clocks = <&scmi_clk CK_SCMI_HASH1>;
+	resets = <&scmi_reset RST_SCMI_HASH1>;
+};
+
+&i2c4 {
+	clocks = <&scmi_clk CK_SCMI_I2C4>;
+	resets = <&scmi_reset RST_SCMI_I2C4>;
+};
+
+&iwdg2 {
+	clocks = <&rcc IWDG2>, <&scmi_clk CK_SCMI_LSI>;
+};
+
+&mdma1 {
+	resets = <&scmi_reset RST_SCMI_MDMA>;
+};
+
+&mlahb {
+	resets = <&scmi_reset RST_SCMI_MCU>;
+};
+
+&rcc {
+	compatible = "st,stm32mp1-rcc-secure", "syscon";
+	clock-names = "hse", "hsi", "csi", "lse", "lsi";
+	clocks = <&scmi_clk CK_SCMI_HSE>,
+		 <&scmi_clk CK_SCMI_HSI>,
+		 <&scmi_clk CK_SCMI_CSI>,
+		 <&scmi_clk CK_SCMI_LSE>,
+		 <&scmi_clk CK_SCMI_LSI>;
+};
+
+&rng1 {
+	clocks = <&scmi_clk CK_SCMI_RNG1>;
+	resets = <&scmi_reset RST_SCMI_RNG1>;
+};
+
+&rtc {
+	clocks = <&scmi_clk CK_SCMI_RTCAPB>, <&scmi_clk CK_SCMI_RTC>;
+};
diff --git a/arch/arm/boot/dts/stm32mp157c-ed1-scmi.dts b/arch/arm/boot/dts/stm32mp157c-ed1-scmi.dts
new file mode 100644
index 000000000000..9cf0a44d2f47
--- /dev/null
+++ b/arch/arm/boot/dts/stm32mp157c-ed1-scmi.dts
@@ -0,0 +1,84 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2022 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@foss.st.com> for STMicroelectronics.
+ */
+
+/dts-v1/;
+
+#include "stm32mp157c-ed1.dts"
+#include "stm32mp15-scmi.dtsi"
+
+/ {
+	model = "STMicroelectronics STM32MP157C-ED1 SCMI eval daughter";
+	compatible = "st,stm32mp157c-ed1-scmi", "st,stm32mp157c-ed1", "st,stm32mp157";
+
+	reserved-memory {
+		optee@fe000000 {
+			reg = <0xfe000000 0x2000000>;
+			no-map;
+		};
+	};
+};
+
+&cpu0 {
+	clocks = <&scmi_clk CK_SCMI_MPU>;
+};
+
+&cpu1 {
+	clocks = <&scmi_clk CK_SCMI_MPU>;
+};
+
+&cryp1 {
+	clocks = <&scmi_clk CK_SCMI_CRYP1>;
+	resets = <&scmi_reset RST_SCMI_CRYP1>;
+};
+
+&dsi {
+	clocks = <&rcc DSI_K>, <&scmi_clk CK_SCMI_HSE>, <&rcc DSI_PX>;
+};
+
+&gpioz {
+	clocks = <&scmi_clk CK_SCMI_GPIOZ>;
+};
+
+&hash1 {
+	clocks = <&scmi_clk CK_SCMI_HASH1>;
+	resets = <&scmi_reset RST_SCMI_HASH1>;
+};
+
+&i2c4 {
+	clocks = <&scmi_clk CK_SCMI_I2C4>;
+	resets = <&scmi_reset RST_SCMI_I2C4>;
+};
+
+&iwdg2 {
+	clocks = <&rcc IWDG2>, <&scmi_clk CK_SCMI_LSI>;
+};
+
+&mdma1 {
+	resets = <&scmi_reset RST_SCMI_MDMA>;
+};
+
+&mlahb {
+	resets = <&scmi_reset RST_SCMI_MCU>;
+};
+
+&rcc {
+	compatible = "st,stm32mp1-rcc-secure", "syscon";
+	clock-names = "hse", "hsi", "csi", "lse", "lsi";
+	clocks = <&scmi_clk CK_SCMI_HSE>,
+		 <&scmi_clk CK_SCMI_HSI>,
+		 <&scmi_clk CK_SCMI_CSI>,
+		 <&scmi_clk CK_SCMI_LSE>,
+		 <&scmi_clk CK_SCMI_LSI>;
+};
+
+&rng1 {
+	clocks = <&scmi_clk CK_SCMI_RNG1>;
+	resets = <&scmi_reset RST_SCMI_RNG1>;
+};
+
+&rtc {
+	clocks = <&scmi_clk CK_SCMI_RTCAPB>, <&scmi_clk CK_SCMI_RTC>;
+};
diff --git a/arch/arm/boot/dts/stm32mp157c-ed1.dts b/arch/arm/boot/dts/stm32mp157c-ed1.dts
index 46b471d09c50..b1eb688a278a 100644
--- a/arch/arm/boot/dts/stm32mp157c-ed1.dts
+++ b/arch/arm/boot/dts/stm32mp157c-ed1.dts
@@ -384,6 +384,8 @@
 	pinctrl-0 = <&uart4_pins_a>;
 	pinctrl-1 = <&uart4_sleep_pins_a>;
 	pinctrl-2 = <&uart4_idle_pins_a>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
 	status = "okay";
 };
 
diff --git a/arch/arm/boot/dts/stm32mp157c-emsbc-argon.dts b/arch/arm/boot/dts/stm32mp157c-emsbc-argon.dts
new file mode 100644
index 000000000000..33b3f11d24bb
--- /dev/null
+++ b/arch/arm/boot/dts/stm32mp157c-emsbc-argon.dts
@@ -0,0 +1,53 @@
+// SPDX-License-Identifier: (GPL-2.0 or MIT)
+//
+// Copyright (c) 2021 emtrion GmbH
+// Author: Reinhold Müller <reinhold.mueller@emtrion.de>.
+//
+
+/dts-v1/;
+
+#include "stm32mp157c-emstamp-argon.dtsi"
+
+/ {
+	model = "emtrion STM32MP157C emSBC-Argon Developer Board";
+	compatible = "emtrion,stm32mp157c-emsbc-argon", "emtrion,stm32mp157c-emstamp-argon",
+			"st,stm32mp157";
+
+	led: gpio_leds {
+		compatible = "gpio-leds";
+		led-2 {
+			label = "red";
+			gpios = <&gpiof 12 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "none";
+			default-state = "off";
+		};
+		led-3 {
+			label = "green";
+			gpios = <&gpioe 7 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "none";
+			default-state = "off";
+		};
+	};
+};
+
+&dac {
+	status = "okay";
+};
+
+&sdmmc1 {
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc1_b4_pins_a>;
+	pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
+	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
+	cd-gpios = <&gpiob 7 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+	disable-wp;
+	st,neg-edge;
+	bus-width = <4>;
+	vmmc-supply = <&vdd_sd>;
+	status = "okay";
+};
+
+&spi1 {
+	status = "okay";
+};
+
diff --git a/arch/arm/boot/dts/stm32mp157c-emstamp-argon.dtsi b/arch/arm/boot/dts/stm32mp157c-emstamp-argon.dtsi
new file mode 100644
index 000000000000..30156b7546ed
--- /dev/null
+++ b/arch/arm/boot/dts/stm32mp157c-emstamp-argon.dtsi
@@ -0,0 +1,546 @@
+// SPDX-License-Identifier: (GPL-2.0 or MIT)
+//
+// Copyright (c) 2021 emtrion GmbH
+// Author: Reinhold Müller <reinhold.mueller@emtrion.de>.
+//
+
+#include "stm32mp157.dtsi"
+#include "stm32mp15xc.dtsi"
+#include "stm32mp15-pinctrl.dtsi"
+#include "stm32mp15xxac-pinctrl.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/mfd/st,stpmic1.h>
+
+/ {
+	aliases {
+		ethernet0 = &ethernet0;
+		serial0 = &uart4;
+		serial1 = &usart2;
+		serial2 = &usart3;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@c0000000 {
+		device_type = "memory";
+		reg = <0xc0000000 0x20000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		mcuram2: mcuram2@10000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10000000 0x40000>;
+			no-map;
+		};
+
+		vdev0vring0: vdev0vring0@10040000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10040000 0x2000>;
+			no-map;
+		};
+
+		vdev0vring1: vdev0vring1@10042000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10042000 0x2000>;
+			no-map;
+		};
+
+		vdev0buffer: vdev0buffer@10044000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10044000 0x4000>;
+			no-map;
+		};
+
+		mcuram: mcuram@30000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x30000000 0x40000>;
+			no-map;
+		};
+
+		retram: retram@38000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x38000000 0x10000>;
+			no-map;
+		};
+
+		gpu_reserved: gpu@dc000000 {
+			reg = <0xdc000000 0x4000000>;
+			no-map;
+		};
+	};
+
+	led: gpio_leds {
+		compatible = "gpio-leds";
+		led-0 {
+			label = "panic";
+			gpios = <&gpioa 13 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "none";
+			default-state = "off";
+			panic-indicator;
+		};
+		led-1 {
+			label = "heartbeat";
+			gpios = <&gpioa 14 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "heartbeat";
+			default-state = "on";
+		};
+	};
+};
+
+&adc {
+	vdd-supply = <&vdd>;
+	vdda-supply = <&vdd>;
+	vref-supply = <&vrefbuf>;
+	status = "okay";
+
+	adc1: adc@0 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&adc1_in6_pins_a>;
+		st,min-sample-time-nsecs = <5000>;
+		st,adc-channels = <6>;
+		status = "disabled";
+	};
+
+	adc2: adc@100 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "okay";
+		channel@12 {
+			reg = <12>;
+			label = "sense_temp";
+			st,min-sample-time-ns = <9000>;
+		};
+		channel@15 {
+			reg = <15>;
+			label = "vbat";
+			st,min-sample-time-ns = <9000>;
+		};
+		channel@16 {
+			reg = <16>;
+			label = "dac_out1";
+			st,min-sample-time-ns = <9000>;
+		};
+		channel@17 {
+			reg = <17>;
+			label = "dac_out1";
+			st,min-sample-time-ns = <9000>;
+		};
+	};
+};
+
+&crc1 {
+	status = "okay";
+};
+
+&cryp1 {
+	status = "okay";
+};
+
+&dac {
+	pinctrl-names = "default";
+	pinctrl-0 = <&dac_ch1_pins_a &dac_ch2_pins_a>;
+	vref-supply = <&vdda>;
+	status = "disabled";
+
+	dac1: dac@1 {
+		status = "okay";
+	};
+	dac2: dac@2 {
+		status = "okay";
+	};
+};
+
+&dts {
+	status = "okay";
+};
+
+&ethernet0 {
+	status = "okay";
+	snps,reset-gpio = <&gpioa 1 GPIO_ACTIVE_LOW>;
+	snps,reset-active-low;
+	snps,reset-delays-us = <0 30000 50000>;
+	pinctrl-0 = <&ethernet0_rmii_pins_b>;
+	pinctrl-1 = <&ethernet0_rmii_sleep_pins_b>;
+	pinctrl-names = "default", "sleep";
+	phy-mode = "rmii";
+	max-speed = <100>;
+	phy-handle = <&phy0>;
+	st,eth-ref-clk-sel;
+
+	mdio0 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+		phy0: ethernet-phy@0 {
+			reg = <0>;
+		};
+	};
+};
+
+&gpu {
+	contiguous-area = <&gpu_reserved>;
+};
+
+&hash1 {
+	status = "okay";
+};
+
+&i2c1 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c1_pins_a>;
+	pinctrl-1 = <&i2c1_sleep_pins_a>;
+	i2c-scl-rising-time-ns = <100>;
+	i2c-scl-falling-time-ns = <7>;
+	status = "disabled";
+	/delete-property/dmas;
+	/delete-property/dma-names;
+};
+
+&i2c4 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c4_pins_a>;
+	pinctrl-1 = <&i2c4_sleep_pins_a>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+	/delete-property/dmas;
+	/delete-property/dma-names;
+
+	pmic: stpmic@33 {
+		compatible = "st,stpmic1";
+		reg = <0x33>;
+		interrupts-extended = <&gpioa 0 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		status = "okay";
+
+		regulators {
+			compatible = "st,stpmic1-regulators";
+
+			ldo1-supply = <&v3v3>;
+			ldo3-supply = <&vdd_ddr>;
+			ldo6-supply = <&v3v3>;
+			pwr_sw1-supply = <&bst_out>;
+			pwr_sw2-supply = <&bst_out>;
+
+			vddcore: buck1 {
+				regulator-name = "vddcore";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+				regulator-initial-mode = <0>;
+				regulator-over-current-protection;
+			};
+
+			vdd_ddr: buck2 {
+				regulator-name = "vdd_ddr";
+				regulator-min-microvolt = <1350000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-always-on;
+				regulator-initial-mode = <0>;
+				regulator-over-current-protection;
+			};
+
+			vdd: buck3 {
+				regulator-name = "vdd";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				st,mask-reset;
+				regulator-initial-mode = <0>;
+				regulator-over-current-protection;
+			};
+
+			v3v3: buck4 {
+				regulator-name = "v3v3";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				regulator-over-current-protection;
+				regulator-initial-mode = <0>;
+			};
+
+			v1v8_audio: ldo1 {
+				regulator-name = "v1v8_audio";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+				interrupts = <IT_CURLIM_LDO1 0>;
+			};
+
+			v3v3_hdmi: ldo2 {
+				regulator-name = "v3v3_hdmi";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				interrupts = <IT_CURLIM_LDO2 0>;
+			};
+
+			vtt_ddr: ldo3 {
+				regulator-name = "vtt_ddr";
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <750000>;
+				regulator-always-on;
+				regulator-over-current-protection;
+			};
+
+			vdd_usb: ldo4 {
+				regulator-name = "vdd_usb";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				interrupts = <IT_CURLIM_LDO4 0>;
+			};
+
+			vdd_sd: ldo5 {
+				regulator-name = "vdd_sd";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				interrupts = <IT_CURLIM_LDO5 0>;
+				regulator-always-on;
+			};
+
+			vdda: ldo6 {
+				regulator-name = "vdda";
+				regulator-min-microvolt = <2900000>;
+				regulator-max-microvolt = <2900000>;
+				regulator-always-on;
+				interrupts = <IT_CURLIM_LDO6 0>;
+				regulator-boot-on;
+			};
+
+			vref_ddr: vref_ddr {
+				regulator-name = "vref_ddr";
+				regulator-always-on;
+				regulator-over-current-protection;
+			};
+
+			bst_out: boost {
+				regulator-name = "bst_out";
+				interrupts = <IT_OCP_BOOST 0>;
+			};
+
+			vbus_otg: pwr_sw1 {
+				regulator-name = "vbus_otg";
+				interrupts = <IT_OCP_OTG 0>;
+				regulator-active-discharge;
+			};
+
+			vbus_usbh: pwr_sw2 {
+				regulator-name = "usbh_vbus";
+				interrupts = <IT_OCP_SWOUT 0>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+		};
+
+		onkey {
+			compatible = "st,stpmic1-onkey";
+			interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 1>;
+			interrupt-names = "onkey-falling", "onkey-rising";
+			status = "okay";
+		};
+
+		watchdog {
+			compatible = "st,stpmic1-wdt";
+			status = "disabled";
+		};
+	};
+};
+
+&i2c5 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&i2c5_pins_a>;
+	pinctrl-1 = <&i2c5_sleep_pins_a>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+};
+
+&ipcc {
+	status = "okay";
+};
+
+&iwdg2 {
+	timeout-sec = <32>;
+	status = "okay";
+};
+
+&m4_rproc {
+	memory-region = <&retram>, <&mcuram>, <&mcuram2>, <&vdev0vring0>,
+			<&vdev0vring1>, <&vdev0buffer>;
+	mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>;
+	mbox-names = "vq0", "vq1", "shutdown";
+	interrupt-parent = <&exti>;
+	interrupts = <68 1>;
+	interrupt-names = "wdg";
+	recovery;
+	status = "okay";
+};
+
+&pwr_regulators {
+	vdd-supply = <&vdd>;
+	vdd_3v3_usbfs-supply = <&vdd_usb>;
+};
+
+&qspi {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a>;
+	pinctrl-1 = <&qspi_clk_sleep_pins_a &qspi_bk1_sleep_pins_a>;
+	reg = <0x58003000 0x1000>, <0x70000000 0x4000000>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	flash0: flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <133000000>;
+		spi-rx-bus-width = <1>;
+		spi-tx-bus-width = <1>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+	};
+};
+
+&rng1 {
+	status = "okay";
+};
+
+&rtc {
+	status = "okay";
+};
+
+&sdmmc2 {
+	arm,primecell-periphid = <0x10153180>;
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc2_b4_pins_b>;
+	pinctrl-1 = <&sdmmc2_b4_od_pins_b>;
+	pinctrl-2 = <&sdmmc2_b4_sleep_pins_a>;
+	non-removable;
+	st,neg-edge;
+	bus-width = <4>;
+	vmmc-supply = <&v3v3>;
+	status = "okay";
+};
+
+&spi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi1_pins_a>;
+	cs-gpios = <&gpioz 3 0>;
+	status = "disabled";
+};
+
+&timers1 {
+	/* spare dmas for other usage */
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	pwm {
+		pinctrl-0 = <&pwm1_pins_b>;
+		pinctrl-1 = <&pwm1_sleep_pins_b>;
+		pinctrl-names = "default", "sleep";
+		status = "okay";
+	};
+	timer@0 {
+		status = "okay";
+	};
+};
+
+&timers4 {
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	pwm {
+		pinctrl-0 = <&pwm4_pins_b>;
+		pinctrl-1 = <&pwm4_sleep_pins_b>;
+		pinctrl-names = "default", "sleep";
+		status = "okay";
+	};
+	timer@3 {
+		status = "okay";
+	};
+};
+
+&timers5 {
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	pwm {
+		pinctrl-0 = <&pwm5_pins_a>;
+		pinctrl-1 = <&pwm5_sleep_pins_a>;
+		pinctrl-names = "default", "sleep";
+		status = "okay";
+	};
+	timer@4 {
+		status = "okay";
+	};
+};
+
+&uart4 {
+	pinctrl-names = "default", "sleep", "idle";
+	pinctrl-0 = <&uart4_pins_a>;
+	pinctrl-1 = <&uart4_sleep_pins_a>;
+	pinctrl-2 = <&uart4_idle_pins_a>;
+	status = "okay";
+};
+
+&usart2 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&usart2_pins_a>;
+	pinctrl-1 = <&usart2_sleep_pins_a>;
+	status = "okay";
+};
+
+&usart3 {
+	pinctrl-names = "default", "sleep", "idle";
+	pinctrl-0 = <&usart3_pins_d>;
+	pinctrl-1 = <&usart3_sleep_pins_d>;
+	pinctrl-2 = <&usart3_idle_pins_d>;
+	status = "okay";
+};
+
+&usbh_ehci {
+	phys = <&usbphyc_port0>;
+	phy-names = "usb";
+	status = "okay";
+};
+
+&usbh_ohci {
+	phys = <&usbphyc_port0>;
+	phy-names = "usb";
+	status = "okay";
+};
+
+&usbotg_hs {
+	dr_mode = "peripheral";
+	pinctrl-names = "default";
+	pinctrl-0 = <&usbotg_hs_pins_a>;
+	phy-names = "usb2-phy";
+	phys = <&usbphyc_port1 0>;
+	vbus-supply = <&vbus_otg>;
+	status = "okay";
+};
+
+&usbphyc {
+	status = "okay";
+};
+
+&usbphyc_port0 {
+	phy-supply = <&vdd_usb>;
+};
+
+&usbphyc_port1 {
+	phy-supply = <&vdd_usb>;
+};
+
+&vrefbuf {
+	regulator-min-microvolt = <2500000>;
+	regulator-max-microvolt = <2500000>;
+	vdda-supply = <&vdd>;
+	status = "okay";
+};
+
diff --git a/arch/arm/boot/dts/stm32mp157c-ev1-scmi.dts b/arch/arm/boot/dts/stm32mp157c-ev1-scmi.dts
new file mode 100644
index 000000000000..3b9dd6f4ccc9
--- /dev/null
+++ b/arch/arm/boot/dts/stm32mp157c-ev1-scmi.dts
@@ -0,0 +1,90 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/*
+ * Copyright (C) STMicroelectronics 2022 - All Rights Reserved
+ * Author: Alexandre Torgue <alexandre.torgue@foss.st.com> for STMicroelectronics.
+ */
+
+/dts-v1/;
+
+#include "stm32mp157c-ev1.dts"
+#include "stm32mp15-scmi.dtsi"
+
+/ {
+	model = "STMicroelectronics STM32MP157C-EV1 SCMI eval daughter on eval mother";
+	compatible = "st,stm32mp157c-ev1-scmi", "st,stm32mp157c-ev1", "st,stm32mp157c-ed1",
+		     "st,stm32mp157";
+
+	reserved-memory {
+		optee@fe000000 {
+			reg = <0xfe000000 0x2000000>;
+			no-map;
+		};
+	};
+};
+
+&cpu0 {
+	clocks = <&scmi_clk CK_SCMI_MPU>;
+};
+
+&cpu1 {
+	clocks = <&scmi_clk CK_SCMI_MPU>;
+};
+
+&cryp1 {
+	clocks = <&scmi_clk CK_SCMI_CRYP1>;
+	resets = <&scmi_reset RST_SCMI_CRYP1>;
+};
+
+&dsi {
+	phy-dsi-supply = <&scmi_reg18>;
+	clocks = <&rcc DSI_K>, <&scmi_clk CK_SCMI_HSE>, <&rcc DSI_PX>;
+};
+
+&gpioz {
+	clocks = <&scmi_clk CK_SCMI_GPIOZ>;
+};
+
+&hash1 {
+	clocks = <&scmi_clk CK_SCMI_HASH1>;
+	resets = <&scmi_reset RST_SCMI_HASH1>;
+};
+
+&i2c4 {
+	clocks = <&scmi_clk CK_SCMI_I2C4>;
+	resets = <&scmi_reset RST_SCMI_I2C4>;
+};
+
+&iwdg2 {
+	clocks = <&rcc IWDG2>, <&scmi_clk CK_SCMI_LSI>;
+};
+
+&m_can1 {
+	clocks = <&scmi_clk CK_SCMI_HSE>, <&rcc FDCAN_K>;
+};
+
+&mdma1 {
+	resets = <&scmi_reset RST_SCMI_MDMA>;
+};
+
+&mlahb {
+	resets = <&scmi_reset RST_SCMI_MCU>;
+};
+
+&rcc {
+	compatible = "st,stm32mp1-rcc-secure", "syscon";
+	clock-names = "hse", "hsi", "csi", "lse", "lsi";
+	clocks = <&scmi_clk CK_SCMI_HSE>,
+		 <&scmi_clk CK_SCMI_HSI>,
+		 <&scmi_clk CK_SCMI_CSI>,
+		 <&scmi_clk CK_SCMI_LSE>,
+		 <&scmi_clk CK_SCMI_LSI>;
+};
+
+&rng1 {
+	clocks = <&scmi_clk CK_SCMI_RNG1>;
+	resets = <&scmi_reset RST_SCMI_RNG1>;
+};
+
+&rtc {
+	clocks = <&scmi_clk CK_SCMI_RTCAPB>, <&scmi_clk CK_SCMI_RTC>;
+};
diff --git a/arch/arm/boot/dts/stm32mp157c-ev1.dts b/arch/arm/boot/dts/stm32mp157c-ev1.dts
index 5c5b1ddf7bfd..050c3c27a420 100644
--- a/arch/arm/boot/dts/stm32mp157c-ev1.dts
+++ b/arch/arm/boot/dts/stm32mp157c-ev1.dts
@@ -255,14 +255,22 @@
 
 &qspi {
 	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a &qspi_bk2_pins_a>;
-	pinctrl-1 = <&qspi_clk_sleep_pins_a &qspi_bk1_sleep_pins_a &qspi_bk2_sleep_pins_a>;
+	pinctrl-0 = <&qspi_clk_pins_a
+		     &qspi_bk1_pins_a
+		     &qspi_cs1_pins_a
+		     &qspi_bk2_pins_a
+		     &qspi_cs2_pins_a>;
+	pinctrl-1 = <&qspi_clk_sleep_pins_a
+		     &qspi_bk1_sleep_pins_a
+		     &qspi_cs1_sleep_pins_a
+		     &qspi_bk2_sleep_pins_a
+		     &qspi_cs2_sleep_pins_a>;
 	reg = <0x58003000 0x1000>, <0x70000000 0x4000000>;
 	#address-cells = <1>;
 	#size-cells = <0>;
 	status = "okay";
 
-	flash0: mx66l51235l@0 {
+	flash0: flash@0 {
 		compatible = "jedec,spi-nor";
 		reg = <0>;
 		spi-rx-bus-width = <4>;
@@ -271,7 +279,7 @@
 		#size-cells = <1>;
 	};
 
-	flash1: mx66l51235l@1 {
+	flash1: flash@1 {
 		compatible = "jedec,spi-nor";
 		reg = <1>;
 		spi-rx-bus-width = <4>;
@@ -375,3 +383,25 @@
 &usbphyc {
 	status = "okay";
 };
+
+&usbphyc_port0 {
+	st,tune-hs-dc-level = <2>;
+	st,enable-fs-rftime-tuning;
+	st,enable-hs-rftime-reduction;
+	st,trim-hs-current = <15>;
+	st,trim-hs-impedance = <1>;
+	st,tune-squelch-level = <3>;
+	st,tune-hs-rx-offset = <2>;
+	st,no-lsfs-sc;
+};
+
+&usbphyc_port1 {
+	st,tune-hs-dc-level = <2>;
+	st,enable-fs-rftime-tuning;
+	st,enable-hs-rftime-reduction;
+	st,trim-hs-current = <15>;
+	st,trim-hs-impedance = <1>;
+	st,tune-squelch-level = <3>;
+	st,tune-hs-rx-offset = <2>;
+	st,no-lsfs-sc;
+};
diff --git a/arch/arm/boot/dts/stm32mp157c-lxa-mc1.dts b/arch/arm/boot/dts/stm32mp157c-lxa-mc1.dts
index 1e9bf7eea0f1..e8d2ec41d537 100644
--- a/arch/arm/boot/dts/stm32mp157c-lxa-mc1.dts
+++ b/arch/arm/boot/dts/stm32mp157c-lxa-mc1.dts
@@ -248,5 +248,7 @@
 &uart4 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart4_pins_a>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/stm32mp157c-odyssey.dts b/arch/arm/boot/dts/stm32mp157c-odyssey.dts
index 554f5d3bcdc3..ed66d25b8bf3 100644
--- a/arch/arm/boot/dts/stm32mp157c-odyssey.dts
+++ b/arch/arm/boot/dts/stm32mp157c-odyssey.dts
@@ -81,6 +81,8 @@
 &uart4 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart4_pins_a>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
 	status = "okay";
 };
 
diff --git a/arch/arm/boot/dts/stm32mp15xx-dhcom-drc02.dtsi b/arch/arm/boot/dts/stm32mp15xx-dhcom-drc02.dtsi
index 4b10b013ffd5..35b1034aa3cf 100644
--- a/arch/arm/boot/dts/stm32mp15xx-dhcom-drc02.dtsi
+++ b/arch/arm/boot/dts/stm32mp15xx-dhcom-drc02.dtsi
@@ -131,6 +131,8 @@
 &usart3 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&usart3_pins_a>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
 	status = "okay";
 };
 
@@ -144,6 +146,8 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart8_pins_a>;
 	rts-gpios = <&gpioe 6 GPIO_ACTIVE_HIGH>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
 	status = "okay";
 };
 
diff --git a/arch/arm/boot/dts/stm32mp15xx-dhcom-pdk2.dtsi b/arch/arm/boot/dts/stm32mp15xx-dhcom-pdk2.dtsi
index fbf3826933e4..5f586f024060 100644
--- a/arch/arm/boot/dts/stm32mp15xx-dhcom-pdk2.dtsi
+++ b/arch/arm/boot/dts/stm32mp15xx-dhcom-pdk2.dtsi
@@ -287,6 +287,8 @@
 &usart3 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&usart3_pins_a>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
 	status = "okay";
 };
 
@@ -294,6 +296,8 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart8_pins_a &uart8_rtscts_pins_a>;
 	uart-has-rtscts;
+	/delete-property/dmas;
+	/delete-property/dma-names;
 	status = "okay";
 };
 
diff --git a/arch/arm/boot/dts/stm32mp15xx-dhcom-picoitx.dtsi b/arch/arm/boot/dts/stm32mp15xx-dhcom-picoitx.dtsi
index ba816ef8b9b2..abc595350e71 100644
--- a/arch/arm/boot/dts/stm32mp15xx-dhcom-picoitx.dtsi
+++ b/arch/arm/boot/dts/stm32mp15xx-dhcom-picoitx.dtsi
@@ -105,12 +105,16 @@
 &usart3 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&usart3_pins_a>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
 	status = "okay";
 };
 
 &uart8 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart8_pins_a &uart8_rtscts_pins_a>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
 	status = "okay";
 };
 
diff --git a/arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi b/arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi
index 8c41f819f776..238a611192e7 100644
--- a/arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi
+++ b/arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi
@@ -118,13 +118,12 @@
 
 &ethernet0 {
 	status = "okay";
-	pinctrl-0 = <&ethernet0_rmii_pins_a>;
-	pinctrl-1 = <&ethernet0_rmii_sleep_pins_a>;
+	pinctrl-0 = <&ethernet0_rmii_pins_c &mco2_pins_a>;
+	pinctrl-1 = <&ethernet0_rmii_sleep_pins_c &mco2_sleep_pins_a>;
 	pinctrl-names = "default", "sleep";
 	phy-mode = "rmii";
 	max-speed = <100>;
 	phy-handle = <&phy0>;
-	st,eth-ref-clk-sel;
 
 	mdio0 {
 		#address-cells = <1>;
@@ -136,7 +135,7 @@
 			/* LAN8710Ai */
 			compatible = "ethernet-phy-id0007.c0f0",
 				     "ethernet-phy-ieee802.3-c22";
-			clocks = <&rcc ETHCK_K>;
+			clocks = <&rcc CK_MCO2>;
 			reset-gpios = <&gpioh 3 GPIO_ACTIVE_LOW>;
 			reset-assert-us = <500>;
 			reset-deassert-us = <500>;
@@ -196,7 +195,6 @@
 			  "", "", "DHCOM-E", "",
 			  "", "", "", "",
 			  "", "", "", "";
-	status = "okay";
 };
 
 &gpiod {
@@ -447,6 +445,21 @@
 	};
 };
 
+&rcc {
+	/* Connect MCO2 output to ETH_RX_CLK input via pad-pad connection */
+	clocks = <&rcc CK_MCO2>;
+	clock-names = "ETH_RX_CLK/ETH_REF_CLK";
+
+	/*
+	 * Set PLL4P output to 100 MHz to supply SDMMC with faster clock,
+	 * set MCO2 output to 50 MHz to supply ETHRX clock with PLL4P/2,
+	 * so that MCO2 behaves as a divider for the ETHRX clock here.
+	 */
+	assigned-clocks = <&rcc CK_MCO2>, <&rcc PLL4_P>;
+	assigned-clock-parents = <&rcc PLL4_P>;
+	assigned-clock-rates = <50000000>, <100000000>;
+};
+
 &rng1 {
 	status = "okay";
 };
@@ -521,5 +534,7 @@
 &uart4 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart4_pins_a>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/stm32mp15xx-dhcor-avenger96.dtsi b/arch/arm/boot/dts/stm32mp15xx-dhcor-avenger96.dtsi
index 6885948f3024..90933077d66d 100644
--- a/arch/arm/boot/dts/stm32mp15xx-dhcor-avenger96.dtsi
+++ b/arch/arm/boot/dts/stm32mp15xx-dhcor-avenger96.dtsi
@@ -126,6 +126,22 @@
 	};
 };
 
+&dcmi {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&dcmi_pins_c>;
+	pinctrl-1 = <&dcmi_sleep_pins_c>;
+	status = "disabled";
+
+	port {
+		dcmi_0: endpoint {
+			remote-endpoint = <&stmipi_2>;
+			bus-type = <5>;
+			bus-width = <8>;
+			pclk-sample = <0>;
+		};
+	};
+};
+
 &ethernet0 {
 	status = "okay";
 	pinctrl-0 = <&ethernet0_rgmii_pins_c>;
@@ -141,6 +157,7 @@
 		compatible = "snps,dwmac-mdio";
 		reset-gpios = <&gpioz 2 GPIO_ACTIVE_LOW>;
 		reset-delay-us = <1000>;
+		reset-post-delay-us = <1000>;
 
 		phy0: ethernet-phy@7 {
 			reg = <7>;
@@ -218,6 +235,45 @@
 };
 
 &i2c4 {
+	stmipi: stmipi@14 {
+		compatible = "st,st-mipid02";
+		pinctrl-names = "default", "sleep";
+		pinctrl-0 = <&mco1_pins_a>;
+		pinctrl-1 = <&mco1_sleep_pins_a>;
+		reg = <0x14>;
+		clocks = <&rcc CK_MCO1>;
+		clock-names = "xclk";
+		assigned-clocks = <&rcc CK_MCO1>;
+		assigned-clock-parents = <&rcc CK_HSE>;
+		assigned-clock-rates = <24000000>;
+		VDDE-supply = <&v1v8>;
+		VDDIN-supply = <&v1v8>;
+		reset-gpios = <&gpioz 0 GPIO_ACTIVE_LOW>;
+		status = "disabled";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				stmipi_0: endpoint {
+				};
+			};
+
+			port@2 {
+				reg = <2>;
+				stmipi_2: endpoint {
+					bus-width = <8>;
+					hsync-active = <0>;
+					vsync-active = <0>;
+					pclk-sample = <0>;
+					remote-endpoint = <&dcmi_0>;
+				};
+			};
+		};
+	};
+
 	hdmi-transmitter@3d {
 		compatible = "adi,adv7513";
 		reg = <0x3d>, <0x4d>, <0x2d>, <0x5d>;
@@ -376,6 +432,8 @@
 	label = "LS-UART1";
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart4_pins_b>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
 	status = "okay";
 };
 
@@ -385,6 +443,8 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart7_pins_a>;
 	uart-has-rtscts;
+	/delete-property/dmas;
+	/delete-property/dma-names;
 	status = "okay";
 };
 
@@ -394,6 +454,8 @@
 	pinctrl-0 = <&usart2_pins_a>;
 	pinctrl-1 = <&usart2_sleep_pins_a>;
 	st,hw-flow-ctrl;
+	/delete-property/dmas;
+	/delete-property/dma-names;
 	status = "okay";
 
 	bluetooth {
diff --git a/arch/arm/boot/dts/stm32mp15xx-dhcor-drc-compact.dtsi b/arch/arm/boot/dts/stm32mp15xx-dhcor-drc-compact.dtsi
new file mode 100644
index 000000000000..27477bb219de
--- /dev/null
+++ b/arch/arm/boot/dts/stm32mp15xx-dhcor-drc-compact.dtsi
@@ -0,0 +1,322 @@
+// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause)
+/*
+ * Copyright (C) 2022 Marek Vasut <marex@denx.de>
+ */
+
+/ {
+	aliases {
+		ethernet0 = &ethernet0;
+		ethernet1 = &ksz8851;
+		mmc0 = &sdmmc1;
+		rtc0 = &hwrtc;
+		rtc1 = &rtc;
+		serial0 = &uart4;
+		serial1 = &uart8;
+		serial2 = &usart3;
+		serial3 = &uart5;
+		spi0 = &qspi;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	led {
+		compatible = "gpio-leds";
+		led1 {
+			label = "yellow:user0";
+			gpios = <&gpioz 6 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led2 {
+			label = "red:user1";
+			gpios = <&gpioz 3 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+	};
+
+	ethernet_vio: vioregulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vio";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpioh 2 GPIO_ACTIVE_LOW>;
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&vdd>;
+	};
+};
+
+&adc {	/* X11 ADC inputs */
+	pinctrl-names = "default";
+	pinctrl-0 = <&adc12_ain_pins_b>;
+	vdd-supply = <&vdd>;
+	vdda-supply = <&vdda>;
+	vref-supply = <&vdda>;
+	status = "okay";
+
+	adc1: adc@0 {
+		st,adc-channels = <0 1 6>;
+		st,min-sample-time-nsecs = <5000>;
+		status = "okay";
+	};
+
+	adc2: adc@100 {
+		st,adc-channels = <0 1 2>;
+		st,min-sample-time-nsecs = <5000>;
+		status = "okay";
+	};
+};
+
+&ethernet0 {
+	status = "okay";
+	pinctrl-0 = <&ethernet0_rgmii_pins_c>;
+	pinctrl-1 = <&ethernet0_rgmii_sleep_pins_c>;
+	pinctrl-names = "default", "sleep";
+	phy-mode = "rgmii";
+	max-speed = <1000>;
+	phy-handle = <&phy0>;
+
+	mdio0 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+		reset-gpios = <&gpioz 2 GPIO_ACTIVE_LOW>;
+		reset-delay-us = <1000>;
+		reset-post-delay-us = <1000>;
+
+		phy0: ethernet-phy@7 {
+			reg = <7>;
+
+			rxc-skew-ps = <1500>;
+			rxdv-skew-ps = <540>;
+			rxd0-skew-ps = <420>;
+			rxd1-skew-ps = <420>;
+			rxd2-skew-ps = <420>;
+			rxd3-skew-ps = <420>;
+
+			txc-skew-ps = <1440>;
+			txen-skew-ps = <540>;
+			txd0-skew-ps = <420>;
+			txd1-skew-ps = <420>;
+			txd2-skew-ps = <420>;
+			txd3-skew-ps = <420>;
+		};
+	};
+};
+
+&fmc {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&fmc_pins_b>;
+	pinctrl-1 = <&fmc_sleep_pins_b>;
+	status = "okay";
+
+	ksz8851: ethernet@1,0 {
+		compatible = "micrel,ks8851-mll";
+		reg = <1 0x0 0x2>, <1 0x2 0x20000>;
+		interrupt-parent = <&gpioc>;
+		interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
+		bank-width = <2>;
+
+		/* Timing values are in nS */
+		st,fmc2-ebi-cs-mux-enable;
+		st,fmc2-ebi-cs-transaction-type = <4>;
+		st,fmc2-ebi-cs-buswidth = <16>;
+		st,fmc2-ebi-cs-address-setup-ns = <5>;
+		st,fmc2-ebi-cs-address-hold-ns = <5>;
+		st,fmc2-ebi-cs-bus-turnaround-ns = <5>;
+		st,fmc2-ebi-cs-data-setup-ns = <45>;
+		st,fmc2-ebi-cs-data-hold-ns = <1>;
+		st,fmc2-ebi-cs-write-address-setup-ns = <5>;
+		st,fmc2-ebi-cs-write-address-hold-ns = <5>;
+		st,fmc2-ebi-cs-write-bus-turnaround-ns = <5>;
+		st,fmc2-ebi-cs-write-data-setup-ns = <45>;
+		st,fmc2-ebi-cs-write-data-hold-ns = <1>;
+	};
+};
+
+&gpioa {
+	gpio-line-names = "", "", "", "",
+			  "DRCC-VAR2", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "";
+};
+
+&gpioe {
+	gpio-line-names = "", "", "", "",
+			  "", "DRCC-GPIO0", "", "",
+			  "", "", "", "",
+			  "", "", "", "";
+};
+
+&gpiog {
+	gpio-line-names = "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "DRCC-GPIO5", "", "", "";
+};
+
+&gpioh {
+	gpio-line-names = "", "", "", "DRCC-HW2",
+			  "DRCC-GPIO4", "", "", "",
+			  "DRCC-HW1", "DRCC-HW0", "", "DRCC-VAR1",
+			  "DRCC-VAR0", "", "", "DRCC-GPIO6";
+};
+
+&gpioi {
+	gpio-line-names = "", "", "", "",
+			  "", "", "", "DRCC-GPIO2",
+			  "", "DRCC-GPIO1", "", "",
+			  "", "", "", "";
+};
+
+&i2c1 {	/* X11 I2C1 */
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins_b>;
+	i2c-scl-rising-time-ns = <185>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+	/delete-property/dmas;
+	/delete-property/dma-names;
+};
+
+&i2c4 {
+	hwrtc: rtc@32 {
+		compatible = "microcrystal,rv8803";
+		reg = <0x32>;
+	};
+
+	eeprom@50 {
+		compatible = "atmel,24c04";
+		reg = <0x50>;
+		pagesize = <16>;
+	};
+};
+
+&sdmmc1 {	/* MicroSD */
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc1_b4_pins_a>;
+	pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
+	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
+	cd-gpios = <&gpioi 8 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+	disable-wp;
+	st,neg-edge;
+	bus-width = <4>;
+	vmmc-supply = <&vdd>;
+	vqmmc-supply = <&vdd>;
+	status = "okay";
+};
+
+&sdmmc2 {	/* eMMC */
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_c>;
+	pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_c>;
+	pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_c>;
+	bus-width = <8>;
+	no-sd;
+	no-sdio;
+	non-removable;
+	st,neg-edge;
+	vmmc-supply = <&v3v3>;
+	vqmmc-supply = <&vdd>;
+	status = "okay";
+};
+
+&sdmmc3 {	/* SDIO Wi-Fi */
+	pinctrl-names = "default", "opendrain", "sleep";
+	pinctrl-0 = <&sdmmc3_b4_pins_a>;
+	pinctrl-1 = <&sdmmc3_b4_od_pins_a>;
+	pinctrl-2 = <&sdmmc3_b4_sleep_pins_a>;
+	broken-cd;
+	bus-width = <4>;
+	mmc-ddr-3_3v;
+	st,neg-edge;
+	vmmc-supply = <&v3v3>;
+	vqmmc-supply = <&v3v3>;
+	status = "okay";
+};
+
+&spi2 {	/* X11 SPI */
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi2_pins_b>;
+	cs-gpios = <&gpioi 0 0>;
+	status = "disabled";
+	/delete-property/dmas;
+	/delete-property/dma-names;
+};
+
+&uart4 {
+	label = "UART0";
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart4_pins_d>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
+
+&uart5 {	/* X11 UART */
+	label = "X11-UART5";
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart5_pins_a>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
+
+&uart8 {
+	label = "RS485-1";
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart8_pins_a &uart8_rtscts_pins_a>;
+	uart-has-rtscts;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
+
+&usart3 {	/* RS485 or RS232 */
+	label = "RS485-2";
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&usart3_pins_e>;
+	pinctrl-1 = <&usart3_sleep_pins_e>;
+	uart-has-rtscts;
+	/delete-property/dmas;
+	/delete-property/dma-names;
+	status = "okay";
+};
+
+&usbh_ehci {
+	phys = <&usbphyc_port0>;
+	status = "okay";
+};
+
+&usbh_ohci {
+	phys = <&usbphyc_port0>;
+	status = "okay";
+};
+
+&usbotg_hs {
+	dr_mode = "otg";
+	pinctrl-0 = <&usbotg_hs_pins_a>;
+	pinctrl-names = "default";
+	phy-names = "usb2-phy";
+	phys = <&usbphyc_port1 0>;
+	vbus-supply = <&vbus_otg>;
+	status = "okay";
+};
+
+&usbphyc {
+	status = "okay";
+};
+
+&usbphyc_port0 {
+	phy-supply = <&vdd_usb>;
+	connector {
+		compatible = "usb-a-connector";
+		vbus-supply = <&vbus_sw>;
+	};
+};
+
+&usbphyc_port1 {
+	phy-supply = <&vdd_usb>;
+};
diff --git a/arch/arm/boot/dts/stm32mp15xx-dhcor-io1v8.dtsi b/arch/arm/boot/dts/stm32mp15xx-dhcor-io1v8.dtsi
index 75172314d7af..9937b28548c2 100644
--- a/arch/arm/boot/dts/stm32mp15xx-dhcor-io1v8.dtsi
+++ b/arch/arm/boot/dts/stm32mp15xx-dhcor-io1v8.dtsi
@@ -18,6 +18,11 @@
 	};
 };
 
+&vdd {
+	regulator-min-microvolt = <2900000>;
+	regulator-max-microvolt = <2900000>;
+};
+
 &pwr_regulators {
 	vdd-supply = <&vdd_io>;
 };
diff --git a/arch/arm/boot/dts/stm32mp15xx-dhcor-som.dtsi b/arch/arm/boot/dts/stm32mp15xx-dhcor-som.dtsi
index 44ecc4708587..134a798ad3f2 100644
--- a/arch/arm/boot/dts/stm32mp15xx-dhcor-som.dtsi
+++ b/arch/arm/boot/dts/stm32mp15xx-dhcor-som.dtsi
@@ -19,6 +19,48 @@
 		device_type = "memory";
 		reg = <0xc0000000 0x40000000>;
 	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		mcuram2: mcuram2@10000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10000000 0x40000>;
+			no-map;
+		};
+
+		vdev0vring0: vdev0vring0@10040000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10040000 0x1000>;
+			no-map;
+		};
+
+		vdev0vring1: vdev0vring1@10041000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10041000 0x1000>;
+			no-map;
+		};
+
+		vdev0buffer: vdev0buffer@10042000 {
+			compatible = "shared-dma-pool";
+			reg = <0x10042000 0x4000>;
+			no-map;
+		};
+
+		mcuram: mcuram@30000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x30000000 0x40000>;
+			no-map;
+		};
+
+		retram: retram@38000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x38000000 0x10000>;
+			no-map;
+		};
+	};
 };
 
 &crc1 {
@@ -77,8 +119,8 @@
 
 			vdd: buck3 {
 				regulator-name = "vdd";
-				regulator-min-microvolt = <2900000>;
-				regulator-max-microvolt = <2900000>;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
 				regulator-always-on;
 				regulator-initial-mode = <0>;
 				regulator-over-current-protection;
@@ -179,11 +221,25 @@
 	};
 };
 
+&ipcc {
+	status = "okay";
+};
+
 &iwdg2 {
 	timeout-sec = <32>;
 	status = "okay";
 };
 
+&m4_rproc {
+	memory-region = <&retram>, <&mcuram>, <&mcuram2>, <&vdev0vring0>,
+			<&vdev0vring1>, <&vdev0buffer>;
+	mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>;
+	mbox-names = "vq0", "vq1", "shutdown";
+	interrupt-parent = <&exti>;
+	interrupts = <68 1>;
+	status = "okay";
+};
+
 &pwr_regulators {
 	vdd-supply = <&vdd>;
 	vdd_3v3_usbfs-supply = <&vdd_usb>;
diff --git a/arch/arm/boot/dts/stm32mp15xx-dkx.dtsi b/arch/arm/boot/dts/stm32mp15xx-dkx.dtsi
index 48beed0f1f30..8b48d3c89a04 100644
--- a/arch/arm/boot/dts/stm32mp15xx-dkx.dtsi
+++ b/arch/arm/boot/dts/stm32mp15xx-dkx.dtsi
@@ -650,6 +650,8 @@
 	pinctrl-0 = <&uart4_pins_a>;
 	pinctrl-1 = <&uart4_sleep_pins_a>;
 	pinctrl-2 = <&uart4_idle_pins_a>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
 	status = "okay";
 };
 
@@ -658,6 +660,8 @@
 	pinctrl-0 = <&uart7_pins_c>;
 	pinctrl-1 = <&uart7_sleep_pins_c>;
 	pinctrl-2 = <&uart7_idle_pins_c>;
+	/delete-property/dmas;
+	/delete-property/dma-names;
 	status = "disabled";
 };
 
@@ -673,6 +677,14 @@
 &usbh_ehci {
 	phys = <&usbphyc_port0>;
 	status = "okay";
+	#address-cells = <1>;
+	#size-cells = <0>;
+	/* onboard HUB */
+	hub@1 {
+		compatible = "usb424,2514";
+		reg = <1>;
+		vdd-supply = <&v3v3>;
+	};
 };
 
 &usbotg_hs {
@@ -694,10 +706,26 @@
 
 &usbphyc_port0 {
 	phy-supply = <&vdd_usb>;
+	st,tune-hs-dc-level = <2>;
+	st,enable-fs-rftime-tuning;
+	st,enable-hs-rftime-reduction;
+	st,trim-hs-current = <15>;
+	st,trim-hs-impedance = <1>;
+	st,tune-squelch-level = <3>;
+	st,tune-hs-rx-offset = <2>;
+	st,no-lsfs-sc;
 };
 
 &usbphyc_port1 {
 	phy-supply = <&vdd_usb>;
+	st,tune-hs-dc-level = <2>;
+	st,enable-fs-rftime-tuning;
+	st,enable-hs-rftime-reduction;
+	st,trim-hs-current = <15>;
+	st,trim-hs-impedance = <1>;
+	st,tune-squelch-level = <3>;
+	st,tune-hs-rx-offset = <2>;
+	st,no-lsfs-sc;
 };
 
 &vrefbuf {
diff --git a/arch/arm/boot/dts/stm32mp15xx-osd32.dtsi b/arch/arm/boot/dts/stm32mp15xx-osd32.dtsi
index 6706d8311a66..935b7084b5a2 100644
--- a/arch/arm/boot/dts/stm32mp15xx-osd32.dtsi
+++ b/arch/arm/boot/dts/stm32mp15xx-osd32.dtsi
@@ -50,12 +50,6 @@
 			no-map;
 		};
 	};
-
-	reg_sip_eeprom: regulator_eeprom {
-		compatible = "regulator-fixed";
-		regulator-name = "sip_eeprom";
-		regulator-always-on;
-	};
 };
 
 &i2c4 {
@@ -78,6 +72,7 @@
 			compatible = "st,stpmic1-regulators";
 
 			ldo1-supply = <&v3v3>;
+			ldo3-supply = <&vdd_ddr>;
 			ldo6-supply = <&v3v3>;
 			pwr_sw1-supply = <&bst_out>;
 
@@ -203,7 +198,7 @@
 
 	sip_eeprom: eeprom@50 {
 		compatible = "atmel,24c32";
-		vcc-supply = <&reg_sip_eeprom>;
+		vcc-supply = <&vdd>;
 		reg = <0x50>;
 	};
 };
diff --git a/arch/arm/boot/dts/sun4i-a10-inet9f-rev03.dts b/arch/arm/boot/dts/sun4i-a10-inet9f-rev03.dts
index 0a562b2cc5bc..62e7aa587f89 100644
--- a/arch/arm/boot/dts/sun4i-a10-inet9f-rev03.dts
+++ b/arch/arm/boot/dts/sun4i-a10-inet9f-rev03.dts
@@ -63,7 +63,7 @@
 		compatible = "gpio-keys-polled";
 		poll-interval = <20>;
 
-		left-joystick-left {
+		event-left-joystick-left {
 			label = "Left Joystick Left";
 			linux,code = <ABS_X>;
 			linux,input-type = <EV_ABS>;
@@ -71,7 +71,7 @@
 			gpios = <&pio 0 6 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PA6 */
 		};
 
-		left-joystick-right {
+		event-left-joystick-right {
 			label = "Left Joystick Right";
 			linux,code = <ABS_X>;
 			linux,input-type = <EV_ABS>;
@@ -79,7 +79,7 @@
 			gpios = <&pio 0 5 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PA5 */
 		};
 
-		left-joystick-up {
+		event-left-joystick-up {
 			label = "Left Joystick Up";
 			linux,code = <ABS_Y>;
 			linux,input-type = <EV_ABS>;
@@ -87,7 +87,7 @@
 			gpios = <&pio 0 8 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PA8 */
 		};
 
-		left-joystick-down {
+		event-left-joystick-down {
 			label = "Left Joystick Down";
 			linux,code = <ABS_Y>;
 			linux,input-type = <EV_ABS>;
@@ -95,7 +95,7 @@
 			gpios = <&pio 0 9 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PA9 */
 		};
 
-		right-joystick-left {
+		event-right-joystick-left {
 			label = "Right Joystick Left";
 			linux,code = <ABS_Z>;
 			linux,input-type = <EV_ABS>;
@@ -103,7 +103,7 @@
 			gpios = <&pio 0 1 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PA1 */
 		};
 
-		right-joystick-right {
+		event-right-joystick-right {
 			label = "Right Joystick Right";
 			linux,code = <ABS_Z>;
 			linux,input-type = <EV_ABS>;
@@ -111,7 +111,7 @@
 			gpios = <&pio 0 0 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PA0 */
 		};
 
-		right-joystick-up {
+		event-right-joystick-up {
 			label = "Right Joystick Up";
 			linux,code = <ABS_RZ>;
 			linux,input-type = <EV_ABS>;
@@ -119,7 +119,7 @@
 			gpios = <&pio 0 3 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PA3 */
 		};
 
-		right-joystick-down {
+		event-right-joystick-down {
 			label = "Right Joystick Down";
 			linux,code = <ABS_RZ>;
 			linux,input-type = <EV_ABS>;
@@ -127,7 +127,7 @@
 			gpios = <&pio 0 4 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PA4 */
 		};
 
-		dpad-left {
+		event-dpad-left {
 			label = "DPad Left";
 			linux,code = <ABS_HAT0X>;
 			linux,input-type = <EV_ABS>;
@@ -135,7 +135,7 @@
 			gpios = <&pio 7 23 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PH23 */
 		};
 
-		dpad-right {
+		event-dpad-right {
 			label = "DPad Right";
 			linux,code = <ABS_HAT0X>;
 			linux,input-type = <EV_ABS>;
@@ -143,7 +143,7 @@
 			gpios = <&pio 7 24 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PH24 */
 		};
 
-		dpad-up {
+		event-dpad-up {
 			label = "DPad Up";
 			linux,code = <ABS_HAT0Y>;
 			linux,input-type = <EV_ABS>;
@@ -151,7 +151,7 @@
 			gpios = <&pio 7 25 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PH25 */
 		};
 
-		dpad-down {
+		event-dpad-down {
 			label = "DPad Down";
 			linux,code = <ABS_HAT0Y>;
 			linux,input-type = <EV_ABS>;
@@ -159,49 +159,49 @@
 			gpios = <&pio 7 26 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PH26 */
 		};
 
-		x {
+		event-x {
 			label = "Button X";
 			linux,code = <BTN_X>;
 			gpios = <&pio 0 16 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PA16 */
 		};
 
-		y {
+		event-y {
 			label = "Button Y";
 			linux,code = <BTN_Y>;
 			gpios = <&pio 0 14 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PA14 */
 		};
 
-		a {
+		event-a {
 			label = "Button A";
 			linux,code = <BTN_A>;
 			gpios = <&pio 0 17 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PA17 */
 		};
 
-		b {
+		event-b {
 			label = "Button B";
 			linux,code = <BTN_B>;
 			gpios = <&pio 0 15 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PA15 */
 		};
 
-		select {
+		event-select {
 			label = "Select Button";
 			linux,code = <BTN_SELECT>;
 			gpios = <&pio 0 11 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PA11 */
 		};
 
-		start {
+		event-start {
 			label = "Start Button";
 			linux,code = <BTN_START>;
 			gpios = <&pio 0 12 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PA12 */
 		};
 
-		top-left {
+		event-top-left {
 			label = "Top Left Button";
 			linux,code = <BTN_TL>;
 			gpios = <&pio 7 22 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PH22 */
 		};
 
-		top-right {
+		event-top-right {
 			label = "Top Right Button";
 			linux,code = <BTN_TR>;
 			gpios = <&pio 0 13 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; /* PA13 */
diff --git a/arch/arm/boot/dts/sun4i-a10-pcduino.dts b/arch/arm/boot/dts/sun4i-a10-pcduino.dts
index 1ac82376baef..a332d61fd561 100644
--- a/arch/arm/boot/dts/sun4i-a10-pcduino.dts
+++ b/arch/arm/boot/dts/sun4i-a10-pcduino.dts
@@ -77,19 +77,19 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		back {
+		key-back {
 			label = "Key Back";
 			linux,code = <KEY_BACK>;
 			gpios = <&pio 7 17 GPIO_ACTIVE_LOW>;
 		};
 
-		home {
+		key-home {
 			label = "Key Home";
 			linux,code = <KEY_HOME>;
 			gpios = <&pio 7 18 GPIO_ACTIVE_LOW>;
 		};
 
-		menu {
+		key-menu {
 			label = "Key Menu";
 			linux,code = <KEY_MENU>;
 			gpios = <&pio 7 19 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/sun5i-a13-licheepi-one.dts b/arch/arm/boot/dts/sun5i-a13-licheepi-one.dts
index 2ce361f8fede..3a6c4bd0a44f 100644
--- a/arch/arm/boot/dts/sun5i-a13-licheepi-one.dts
+++ b/arch/arm/boot/dts/sun5i-a13-licheepi-one.dts
@@ -67,18 +67,18 @@
 		compatible = "gpio-leds";
 
 		led-0 {
-			label ="licheepi:red:usr";
+			label = "licheepi:red:usr";
 			gpios = <&pio 2 5 GPIO_ACTIVE_LOW>;
 		};
 
 		led-1 {
-			label ="licheepi:green:usr";
+			label = "licheepi:green:usr";
 			gpios = <&pio 2 19 GPIO_ACTIVE_LOW>;
 			default-state = "on";
 		};
 
 		led-2 {
-			label ="licheepi:blue:usr";
+			label = "licheepi:blue:usr";
 			gpios = <&pio 2 4 GPIO_ACTIVE_LOW>;
 		};
 
diff --git a/arch/arm/boot/dts/sun6i-a31.dtsi b/arch/arm/boot/dts/sun6i-a31.dtsi
index 715d74854449..6cdadba6a3ac 100644
--- a/arch/arm/boot/dts/sun6i-a31.dtsi
+++ b/arch/arm/boot/dts/sun6i-a31.dtsi
@@ -46,6 +46,7 @@
 #include <dt-bindings/thermal/thermal.h>
 
 #include <dt-bindings/clock/sun6i-a31-ccu.h>
+#include <dt-bindings/clock/sun6i-rtc.h>
 #include <dt-bindings/reset/sun6i-a31-ccu.h>
 
 / {
@@ -598,7 +599,7 @@
 		ccu: clock@1c20000 {
 			compatible = "allwinner,sun6i-a31-ccu";
 			reg = <0x01c20000 0x400>;
-			clocks = <&osc24M>, <&rtc 0>;
+			clocks = <&osc24M>, <&rtc CLK_OSC32K>;
 			clock-names = "hosc", "losc";
 			#clock-cells = <1>;
 			#reset-cells = <1>;
@@ -612,7 +613,8 @@
 				     <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&ccu CLK_APB1_PIO>, <&osc24M>, <&rtc 0>;
+			clocks = <&ccu CLK_APB1_PIO>, <&osc24M>,
+				 <&rtc CLK_OSC32K>;
 			clock-names = "apb", "hosc", "losc";
 			gpio-controller;
 			interrupt-controller;
@@ -1319,7 +1321,7 @@
 			ar100: ar100_clk {
 				compatible = "allwinner,sun6i-a31-ar100-clk";
 				#clock-cells = <0>;
-				clocks = <&rtc 0>, <&osc24M>,
+				clocks = <&rtc CLK_OSC32K>, <&osc24M>,
 					 <&ccu CLK_PLL_PERIPH>,
 					 <&ccu CLK_PLL_PERIPH>;
 				clock-output-names = "ar100";
@@ -1354,7 +1356,7 @@
 			ir_clk: ir_clk {
 				#clock-cells = <0>;
 				compatible = "allwinner,sun4i-a10-mod0-clk";
-				clocks = <&rtc 0>, <&osc24M>;
+				clocks = <&rtc CLK_OSC32K>, <&osc24M>;
 				clock-output-names = "ir";
 			};
 
@@ -1385,9 +1387,8 @@
 			interrupt-parent = <&r_intc>;
 			interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&apb0_gates 0>, <&osc24M>, <&rtc 0>;
+			clocks = <&apb0_gates 0>, <&osc24M>, <&rtc CLK_OSC32K>;
 			clock-names = "apb", "hosc", "losc";
-			resets = <&apb0_rst 0>;
 			gpio-controller;
 			interrupt-controller;
 			#interrupt-cells = <3>;
diff --git a/arch/arm/boot/dts/sun7i-a20-haoyu-marsboard.dts b/arch/arm/boot/dts/sun7i-a20-haoyu-marsboard.dts
new file mode 100644
index 000000000000..097e479c2772
--- /dev/null
+++ b/arch/arm/boot/dts/sun7i-a20-haoyu-marsboard.dts
@@ -0,0 +1,182 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2021 Conley Lee
+ * Conley Lee <conleylee@foxmail.com>
+ */
+
+/dts-v1/;
+#include "sun7i-a20.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	model = "HAOYU Electronics Marsboard A20";
+	compatible = "haoyu,a20-marsboard", "allwinner,sun7i-a20";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	hdmi-connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con_in: endpoint {
+				remote-endpoint = <&hdmi_out_con>;
+			};
+		};
+	};
+};
+
+&ahci {
+	target-supply = <&reg_ahci_5v>;
+	status = "okay";
+};
+
+&codec {
+	status = "okay";
+};
+
+&cpu0 {
+	cpu-supply = <&reg_dcdc2>;
+};
+
+&de {
+	status = "okay";
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&gmac {
+	pinctrl-names = "default";
+	pinctrl-0 = <&gmac_mii_pins>, <&gmac_txerr>;
+	phy-handle = <&phy0>;
+	phy-mode = "mii";
+	status = "okay";
+};
+
+&hdmi {
+	status = "okay";
+};
+
+&hdmi_out {
+	hdmi_out_con: endpoint {
+		remote-endpoint = <&hdmi_con_in>;
+	};
+};
+
+&i2c0 {
+	status = "okay";
+
+	axp209: pmic@34 {
+		reg = <0x34>;
+		interrupt-parent = <&nmi_intc>;
+		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
+&mmc0 {
+	vmmc-supply = <&reg_vcc3v3>;
+	bus-width = <4>;
+	cd-gpios = <&pio 7 10 GPIO_ACTIVE_LOW>; /* PH10 */
+	status = "okay";
+};
+
+&gmac_mdio {
+	phy0: ethernet-phy@0 {
+		reg = <0>;
+	};
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&otg_sram {
+	status = "okay";
+};
+
+&pio {
+	gmac_txerr: gmac-txerr-pin {
+		pins = "PA17";
+		function = "gmac";
+	};
+};
+
+&reg_ahci_5v {
+	status = "okay";
+};
+
+#include "axp209.dtsi"
+
+&ac_power_supply {
+	status = "okay";
+};
+
+&reg_dcdc2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1000000>;
+	regulator-max-microvolt = <1450000>;
+	regulator-name = "vdd-cpu";
+};
+
+&reg_dcdc3 {
+	regulator-always-on;
+	regulator-min-microvolt = <1000000>;
+	regulator-max-microvolt = <1400000>;
+	regulator-name = "vdd-int-dll";
+};
+
+&reg_ldo1 {
+	regulator-name = "vdd-rtc";
+};
+
+&reg_ldo2 {
+	regulator-always-on;
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+	regulator-name = "avcc";
+};
+
+&reg_usb1_vbus {
+	status = "okay";
+};
+
+&reg_usb2_vbus {
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pb_pins>;
+	status = "okay";
+};
+
+&usb_otg {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&usbphy {
+	usb0_id_det-gpios = <&pio 7 4 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>; /* PH4 */
+	usb1_vbus-supply = <&reg_usb1_vbus>;
+	usb2_vbus-supply = <&reg_usb2_vbus>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/sun7i-a20-pcduino3.dts b/arch/arm/boot/dts/sun7i-a20-pcduino3.dts
index 4f8d55d3ba79..928b86a95f34 100644
--- a/arch/arm/boot/dts/sun7i-a20-pcduino3.dts
+++ b/arch/arm/boot/dts/sun7i-a20-pcduino3.dts
@@ -78,19 +78,19 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		back {
+		key-back {
 			label = "Key Back";
 			linux,code = <KEY_BACK>;
 			gpios = <&pio 7 17 GPIO_ACTIVE_LOW>;
 		};
 
-		home {
+		key-home {
 			label = "Key Home";
 			linux,code = <KEY_HOME>;
 			gpios = <&pio 7 18 GPIO_ACTIVE_LOW>;
 		};
 
-		menu {
+		key-menu {
 			label = "Key Menu";
 			linux,code = <KEY_MENU>;
 			gpios = <&pio 7 19 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/sun8i-a23-a33.dtsi b/arch/arm/boot/dts/sun8i-a23-a33.dtsi
index 4461d5098b20..f630ab55bb6a 100644
--- a/arch/arm/boot/dts/sun8i-a23-a33.dtsi
+++ b/arch/arm/boot/dts/sun8i-a23-a33.dtsi
@@ -44,6 +44,7 @@
 
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 
+#include <dt-bindings/clock/sun6i-rtc.h>
 #include <dt-bindings/clock/sun8i-a23-a33-ccu.h>
 #include <dt-bindings/reset/sun8i-a23-a33-ccu.h>
 
@@ -329,7 +330,7 @@
 
 		ccu: clock@1c20000 {
 			reg = <0x01c20000 0x400>;
-			clocks = <&osc24M>, <&rtc 0>;
+			clocks = <&osc24M>, <&rtc CLK_OSC32K>;
 			clock-names = "hosc", "losc";
 			#clock-cells = <1>;
 			#reset-cells = <1>;
@@ -340,7 +341,8 @@
 			reg = <0x01c20800 0x400>;
 			interrupt-parent = <&r_intc>;
 			/* interrupts get set in SoC specific dtsi file */
-			clocks = <&ccu CLK_BUS_PIO>, <&osc24M>, <&rtc 0>;
+			clocks = <&ccu CLK_BUS_PIO>, <&osc24M>,
+				 <&rtc CLK_OSC32K>;
 			clock-names = "apb", "hosc", "losc";
 			gpio-controller;
 			interrupt-controller;
@@ -810,9 +812,8 @@
 			reg = <0x01f02c00 0x400>;
 			interrupt-parent = <&r_intc>;
 			interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&apb0_gates 0>, <&osc24M>, <&rtc 0>;
+			clocks = <&apb0_gates 0>, <&osc24M>, <&rtc CLK_OSC32K>;
 			clock-names = "apb", "hosc", "losc";
-			resets = <&apb0_rst 0>;
 			gpio-controller;
 			interrupt-controller;
 			#interrupt-cells = <3>;
diff --git a/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts b/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
index 8e8634ff2f9d..d729b7c705db 100644
--- a/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
+++ b/arch/arm/boot/dts/sun8i-h2-plus-bananapi-m2-zero.dts
@@ -47,13 +47,14 @@
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
-		sw4 {
+		switch-4 {
 			label = "power";
-			linux,code = <BTN_0>;
+			linux,code = <KEY_POWER>;
 			gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
+			wakeup-source;
 		};
 	};
 
@@ -105,7 +106,7 @@
 	wifi_pwrseq: wifi_pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
-		clocks = <&rtc 1>;
+		clocks = <&rtc CLK_OSC32K_FANOUT>;
 		clock-names = "ext_clock";
 	};
 };
@@ -180,7 +181,7 @@
 	bluetooth {
 		compatible = "brcm,bcm43438-bt";
 		max-speed = <1500000>;
-		clocks = <&rtc 1>;
+		clocks = <&rtc CLK_OSC32K_FANOUT>;
 		clock-names = "lpo";
 		vbat-supply = <&reg_vcc3v3>;
 		vddio-supply = <&reg_vcc3v3>;
diff --git a/arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dts b/arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dts
index f19ed981da9d..3706216ffb40 100644
--- a/arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dts
+++ b/arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dts
@@ -169,7 +169,7 @@
 	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		compatible = "mxicy,mx25l1606e", "winbond,w25q128";
+		compatible = "mxicy,mx25l1606e", "jedec,spi-nor";
 		reg = <0>;
 		spi-max-frequency = <40000000>;
 	};
diff --git a/arch/arm/boot/dts/sun8i-h3-beelink-x2.dts b/arch/arm/boot/dts/sun8i-h3-beelink-x2.dts
index f0e591e1c771..27a0d51289dd 100644
--- a/arch/arm/boot/dts/sun8i-h3-beelink-x2.dts
+++ b/arch/arm/boot/dts/sun8i-h3-beelink-x2.dts
@@ -57,6 +57,12 @@
 		ethernet1 = &sdiowifi;
 	};
 
+	cec-gpio {
+		compatible = "cec-gpio";
+		cec-gpios = <&pio 0 14 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; /* PA14 */
+		hdmi-phandle = <&hdmi>;
+	};
+
 	chosen {
 		stdout-path = "serial0:115200n8";
 	};
@@ -87,11 +93,15 @@
 		};
 	};
 
-	wifi_pwrseq: wifi_pwrseq {
-		compatible = "mmc-pwrseq-simple";
-		reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
-		clocks = <&rtc 1>;
-		clock-names = "ext_clock";
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		key-power {
+			label = "power";
+			linux,code = <KEY_POWER>;
+			gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
+			wakeup-source;
+		};
 	};
 
 	sound_spdif {
@@ -112,15 +122,11 @@
 		compatible = "linux,spdif-dit";
 	};
 
-	r-gpio-keys {
-		compatible = "gpio-keys";
-
-		power {
-			label = "power";
-			linux,code = <KEY_POWER>;
-			gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
-			wakeup-source;
-		};
+	wifi_pwrseq: wifi_pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
+		clocks = <&rtc CLK_OSC32K_FANOUT>;
+		clock-names = "ext_clock";
 	};
 };
 
diff --git a/arch/arm/boot/dts/sun8i-h3-mapleboard-mp130.dts b/arch/arm/boot/dts/sun8i-h3-mapleboard-mp130.dts
index ff0a7a952e0c..f5c8ccc5b872 100644
--- a/arch/arm/boot/dts/sun8i-h3-mapleboard-mp130.dts
+++ b/arch/arm/boot/dts/sun8i-h3-mapleboard-mp130.dts
@@ -39,16 +39,16 @@
 		};
 	};
 
-	r_gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
-		power {
+		key-power {
 			label = "power";
 			linux,code = <KEY_POWER>;
 			gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>; /* PL3 */
 		};
 
-		user {
+		key-user {
 			label = "user";
 			linux,code = <BTN_0>;
 			gpios = <&r_pio 0 4 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/sun8i-h3-nanopi-duo2.dts b/arch/arm/boot/dts/sun8i-h3-nanopi-duo2.dts
index 8e7dfcffe1fb..43641cb82398 100644
--- a/arch/arm/boot/dts/sun8i-h3-nanopi-duo2.dts
+++ b/arch/arm/boot/dts/sun8i-h3-nanopi-duo2.dts
@@ -37,10 +37,10 @@
 		};
 	};
 
-	r_gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
-		k1 {
+		key-0 {
 			label = "k1";
 			linux,code = <BTN_0>;
 			gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>; /* PL3 */
@@ -90,7 +90,7 @@
 	wifi_pwrseq: wifi_pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
-		clocks = <&rtc 1>;
+		clocks = <&rtc CLK_OSC32K_FANOUT>;
 		clock-names = "ext_clock";
 	};
 
@@ -151,7 +151,7 @@
 
 	bluetooth {
 		compatible = "brcm,bcm43438-bt";
-		clocks = <&rtc 1>;
+		clocks = <&rtc CLK_OSC32K_FANOUT>;
 		clock-names = "lpo";
 		vbat-supply = <&reg_vcc3v3>;
 		vddio-supply = <&reg_vcc3v3>;
diff --git a/arch/arm/boot/dts/sun8i-h3-nanopi-neo-air.dts b/arch/arm/boot/dts/sun8i-h3-nanopi-neo-air.dts
index be49eabbff94..9e1a33f94cad 100644
--- a/arch/arm/boot/dts/sun8i-h3-nanopi-neo-air.dts
+++ b/arch/arm/boot/dts/sun8i-h3-nanopi-neo-air.dts
@@ -103,12 +103,40 @@
 	};
 };
 
+&mmc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_8bit_pins>;
+	vmmc-supply = <&reg_vcc3v3>;
+	vqmmc-supply = <&reg_vcc3v3>;
+	bus-width = <8>;
+	non-removable;
+	status = "okay";
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_pa_pins>;
 	status = "okay";
 };
 
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart3_pins>, <&uart3_rts_cts_pins>;
+	uart-has-rtscts;
+	status = "okay";
+
+	bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		clocks = <&rtc CLK_OSC32K_FANOUT>;
+		clock-names = "lpo";
+		vbat-supply = <&reg_vcc3v3>;
+		vddio-supply = <&reg_vcc3v3>;
+		device-wakeup-gpios = <&pio 0 8 GPIO_ACTIVE_HIGH>; /* PA8 */
+		host-wakeup-gpios = <&pio 0 7 GPIO_ACTIVE_HIGH>; /* PA7 */
+		shutdown-gpios = <&pio 6 13 GPIO_ACTIVE_HIGH>; /* PG13 */
+	};
+};
+
 &usbphy {
 	/* USB VBUS is always on */
 	status = "okay";
diff --git a/arch/arm/boot/dts/sun8i-h3-nanopi-neo.dts b/arch/arm/boot/dts/sun8i-h3-nanopi-neo.dts
index 9f33f6fae595..df71fab3cf4e 100644
--- a/arch/arm/boot/dts/sun8i-h3-nanopi-neo.dts
+++ b/arch/arm/boot/dts/sun8i-h3-nanopi-neo.dts
@@ -45,6 +45,10 @@
 / {
 	model = "FriendlyARM NanoPi NEO";
 	compatible = "friendlyarm,nanopi-neo", "allwinner,sun8i-h3";
+
+	aliases {
+		ethernet0 = &emac;
+	};
 };
 
 &ehci0 {
diff --git a/arch/arm/boot/dts/sun8i-h3-nanopi-r1.dts b/arch/arm/boot/dts/sun8i-h3-nanopi-r1.dts
index 26e2e6172e0d..42cd1131adf3 100644
--- a/arch/arm/boot/dts/sun8i-h3-nanopi-r1.dts
+++ b/arch/arm/boot/dts/sun8i-h3-nanopi-r1.dts
@@ -46,7 +46,7 @@
 	wifi_pwrseq: wifi_pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
-		clocks = <&rtc 1>;
+		clocks = <&rtc CLK_OSC32K_FANOUT>;
 		clock-names = "ext_clock";
 	};
 
@@ -147,7 +147,7 @@
 
 	bluetooth {
 		compatible = "brcm,bcm43438-bt";
-		clocks = <&rtc 1>;
+		clocks = <&rtc CLK_OSC32K_FANOUT>;
 		clock-names = "lpo";
 		vbat-supply = <&reg_vcc3v3>;
 		vddio-supply = <&reg_vcc3v3>;
diff --git a/arch/arm/boot/dts/sun8i-h3-nanopi.dtsi b/arch/arm/boot/dts/sun8i-h3-nanopi.dtsi
index c7c3e7d8b3c8..cf8413fba6c1 100644
--- a/arch/arm/boot/dts/sun8i-h3-nanopi.dtsi
+++ b/arch/arm/boot/dts/sun8i-h3-nanopi.dtsi
@@ -73,14 +73,14 @@
 		};
 	};
 
-	r_gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
-		input-name = "k1";
 
-		k1 {
+		key-0 {
 			label = "k1";
 			linux,code = <KEY_POWER>;
 			gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
+			wakeup-source;
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-2.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-2.dts
index 597c425d08ec..f1f9dbead32a 100644
--- a/arch/arm/boot/dts/sun8i-h3-orangepi-2.dts
+++ b/arch/arm/boot/dts/sun8i-h3-orangepi-2.dts
@@ -88,19 +88,20 @@
 		};
 	};
 
-	r_gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
-		sw2 {
+		switch-2 {
 			label = "sw2";
 			linux,code = <BTN_1>;
 			gpios = <&r_pio 0 4 GPIO_ACTIVE_LOW>;
 		};
 
-		sw4 {
+		switch-4 {
 			label = "sw4";
-			linux,code = <BTN_0>;
+			linux,code = <KEY_POWER>;
 			gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
+			wakeup-source;
 		};
 	};
 
diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-lite.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-lite.dts
index 6f9c97add54e..305b34a321f5 100644
--- a/arch/arm/boot/dts/sun8i-h3-orangepi-lite.dts
+++ b/arch/arm/boot/dts/sun8i-h3-orangepi-lite.dts
@@ -87,10 +87,10 @@
 		};
 	};
 
-	r_gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
-		sw4 {
+		switch-4 {
 			label = "sw4";
 			linux,code = <BTN_0>;
 			gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-one.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-one.dts
index 4759ba3f2986..59f6f6d5e7ca 100644
--- a/arch/arm/boot/dts/sun8i-h3-orangepi-one.dts
+++ b/arch/arm/boot/dts/sun8i-h3-orangepi-one.dts
@@ -86,10 +86,10 @@
 		};
 	};
 
-	r_gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
-		sw4 {
+		switch-4 {
 			label = "sw4";
 			linux,code = <BTN_0>;
 			gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts
index 5aff8ecc66cb..b96e015f54ee 100644
--- a/arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts
+++ b/arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts
@@ -86,13 +86,14 @@
 		};
 	};
 
-	r_gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
-		sw4 {
+		switch-4 {
 			label = "sw4";
-			linux,code = <BTN_0>;
+			linux,code = <KEY_POWER>;
 			gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
+			wakeup-source;
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi
index ae4f933abb89..eac2349a2380 100644
--- a/arch/arm/boot/dts/sun8i-h3.dtsi
+++ b/arch/arm/boot/dts/sun8i-h3.dtsi
@@ -245,7 +245,7 @@
 		cpu_thermal: cpu-thermal {
 			polling-delay-passive = <0>;
 			polling-delay = <0>;
-			thermal-sensors = <&ths 0>;
+			thermal-sensors = <&ths>;
 
 			trips {
 				cpu_hot_trip: cpu-hot {
@@ -282,6 +282,10 @@
 	compatible = "allwinner,sun8i-h3-de2-clk";
 };
 
+&mbus {
+	compatible = "allwinner,sun8i-h3-mbus";
+};
+
 &mmc0 {
 	compatible = "allwinner,sun7i-a20-mmc";
 	clocks = <&ccu CLK_BUS_MMC0>,
diff --git a/arch/arm/boot/dts/sun8i-r16-bananapi-m2m.dts b/arch/arm/boot/dts/sun8i-r16-bananapi-m2m.dts
index bf5b5e2f6168..bc394686fedb 100644
--- a/arch/arm/boot/dts/sun8i-r16-bananapi-m2m.dts
+++ b/arch/arm/boot/dts/sun8i-r16-bananapi-m2m.dts
@@ -91,7 +91,7 @@
 	wifi_pwrseq: wifi_pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		reset-gpios = <&r_pio 0 6 GPIO_ACTIVE_LOW>; /* PL06 */
-		clocks = <&rtc 1>;
+		clocks = <&rtc CLK_OSC32K_FANOUT>;
 		clock-names = "ext_clock";
 	};
 };
@@ -283,7 +283,7 @@
 
 	bluetooth {
 		compatible = "brcm,bcm43438-bt";
-		clocks = <&rtc 1>;
+		clocks = <&rtc CLK_OSC32K_FANOUT>;
 		clock-names = "lpo";
 		vbat-supply = <&reg_dldo1>;
 		vddio-supply = <&reg_aldo3>;
diff --git a/arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts b/arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts
index a6a1087a0c9b..28197bbcb1d5 100644
--- a/arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts
+++ b/arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts
@@ -43,6 +43,7 @@
 
 /dts-v1/;
 #include "sun8i-r40.dtsi"
+#include "sun8i-r40-cpu-opp.dtsi"
 
 #include <dt-bindings/gpio/gpio.h>
 
@@ -113,6 +114,10 @@
 	status = "okay";
 };
 
+&cpu0 {
+	cpu-supply = <&reg_dcdc2>;
+};
+
 &de {
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/sun8i-r40-cpu-opp.dtsi b/arch/arm/boot/dts/sun8i-r40-cpu-opp.dtsi
new file mode 100644
index 000000000000..649928b361af
--- /dev/null
+++ b/arch/arm/boot/dts/sun8i-r40-cpu-opp.dtsi
@@ -0,0 +1,52 @@
+/{
+	cpu0_opp_table: opp-table-cpu {
+		compatible = "operating-points-v2";
+		opp-shared;
+
+		opp-720000000 {
+			opp-hz = /bits/ 64 <720000000>;
+			opp-microvolt = <1000000 1000000 1300000>;
+			clock-latency-ns = <2000000>;
+		};
+
+		opp-912000000 {
+			opp-hz = /bits/ 64 <912000000>;
+			opp-microvolt = <1100000 1100000 1300000>;
+			clock-latency-ns = <2000000>;
+		};
+
+		opp-1008000000 {
+			opp-hz = /bits/ 64 <1008000000>;
+			opp-microvolt = <1160000 1160000 1300000>;
+			clock-latency-ns = <2000000>;
+		};
+
+		opp-1104000000 {
+			opp-hz = /bits/ 64 <1104000000>;
+			opp-microvolt = <1240000 1240000 1300000>;
+			clock-latency-ns = <2000000>;
+		};
+
+		opp-1200000000 {
+			opp-hz = /bits/ 64 <1200000000>;
+			opp-microvolt = <1300000 1300000 1300000>;
+			clock-latency-ns = <2000000>;
+		};
+	};
+};
+
+&cpu0 {
+	operating-points-v2 = <&cpu0_opp_table>;
+};
+
+&cpu1 {
+	operating-points-v2 = <&cpu0_opp_table>;
+};
+
+&cpu2 {
+	operating-points-v2 = <&cpu0_opp_table>;
+};
+
+&cpu3 {
+	operating-points-v2 = <&cpu0_opp_table>;
+};
diff --git a/arch/arm/boot/dts/sun8i-r40-feta40i.dtsi b/arch/arm/boot/dts/sun8i-r40-feta40i.dtsi
index 265e0fa57a32..9f39b5a2bb35 100644
--- a/arch/arm/boot/dts/sun8i-r40-feta40i.dtsi
+++ b/arch/arm/boot/dts/sun8i-r40-feta40i.dtsi
@@ -5,6 +5,11 @@
 //  Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io>
 
 #include "sun8i-r40.dtsi"
+#include "sun8i-r40-cpu-opp.dtsi"
+
+&cpu0 {
+	cpu-supply = <&reg_dcdc2>;
+};
 
 &i2c0 {
 	status = "okay";
diff --git a/arch/arm/boot/dts/sun8i-r40.dtsi b/arch/arm/boot/dts/sun8i-r40.dtsi
index 1d87fc0c24ee..4ef26d8f5340 100644
--- a/arch/arm/boot/dts/sun8i-r40.dtsi
+++ b/arch/arm/boot/dts/sun8i-r40.dtsi
@@ -42,6 +42,7 @@
  */
 
 #include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/sun6i-rtc.h>
 #include <dt-bindings/clock/sun8i-de2.h>
 #include <dt-bindings/clock/sun8i-r40-ccu.h>
 #include <dt-bindings/clock/sun8i-tcon-top.h>
@@ -84,24 +85,36 @@
 			compatible = "arm,cortex-a7";
 			device_type = "cpu";
 			reg = <0>;
+			clocks = <&ccu CLK_CPU>;
+			clock-names = "cpu";
+			#cooling-cells = <2>;
 		};
 
 		cpu1: cpu@1 {
 			compatible = "arm,cortex-a7";
 			device_type = "cpu";
 			reg = <1>;
+			clocks = <&ccu CLK_CPU>;
+			clock-names = "cpu";
+			#cooling-cells = <2>;
 		};
 
 		cpu2: cpu@2 {
 			compatible = "arm,cortex-a7";
 			device_type = "cpu";
 			reg = <2>;
+			clocks = <&ccu CLK_CPU>;
+			clock-names = "cpu";
+			#cooling-cells = <2>;
 		};
 
 		cpu3: cpu@3 {
 			compatible = "arm,cortex-a7";
 			device_type = "cpu";
 			reg = <3>;
+			clocks = <&ccu CLK_CPU>;
+			clock-names = "cpu";
+			#cooling-cells = <2>;
 		};
 	};
 
@@ -117,6 +130,30 @@
 			polling-delay-passive = <0>;
 			polling-delay = <0>;
 			thermal-sensors = <&ths 0>;
+
+			trips {
+				cpu_hot_trip: cpu-hot {
+					temperature = <80000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				cpu_very_hot_trip: cpu-very-hot {
+					temperature = <115000>;
+					hysteresis = <0>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				cpu-hot-limit {
+					trip = <&cpu_hot_trip>;
+					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
 		};
 
 		gpu_thermal: gpu-thermal {
@@ -485,7 +522,7 @@
 		ccu: clock@1c20000 {
 			compatible = "allwinner,sun8i-r40-ccu";
 			reg = <0x01c20000 0x400>;
-			clocks = <&osc24M>, <&rtc 0>;
+			clocks = <&osc24M>, <&rtc CLK_OSC32K>;
 			clock-names = "hosc", "losc";
 			#clock-cells = <1>;
 			#reset-cells = <1>;
@@ -504,13 +541,24 @@
 			compatible = "allwinner,sun8i-r40-pinctrl";
 			reg = <0x01c20800 0x400>;
 			interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&ccu CLK_BUS_PIO>, <&osc24M>, <&rtc 0>;
+			clocks = <&ccu CLK_BUS_PIO>, <&osc24M>,
+				 <&rtc CLK_OSC32K>;
 			clock-names = "apb", "hosc", "losc";
 			gpio-controller;
 			interrupt-controller;
 			#interrupt-cells = <3>;
 			#gpio-cells = <3>;
 
+			can_ph_pins: can-ph-pins {
+				pins = "PH20", "PH21";
+				function = "can";
+			};
+
+			can_pa_pins: can-pa-pins {
+				pins = "PA16", "PA17";
+				function = "can";
+			};
+
 			clk_out_a_pin: clk-out-a-pin {
 				pins = "PI12";
 				function = "clk_out_a";
@@ -926,6 +974,15 @@
 			#size-cells = <0>;
 		};
 
+		can0: can@1c2bc00 {
+			compatible = "allwinner,sun8i-r40-can";
+			reg = <0x01c2bc00 0x400>;
+			interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_CAN>;
+			resets = <&ccu RST_BUS_CAN>;
+			status = "disabled";
+		};
+
 		i2c4: i2c@1c2c000 {
 			compatible = "allwinner,sun6i-a31-i2c";
 			reg = <0x01c2c000 0x400>;
@@ -1212,8 +1269,8 @@
 			reg-io-width = <1>;
 			interrupts = <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&ccu CLK_BUS_HDMI0>, <&ccu CLK_HDMI_SLOW>,
-				 <&ccu CLK_HDMI>;
-			clock-names = "iahb", "isfr", "tmds";
+				 <&ccu CLK_HDMI>, <&rtc CLK_OSC32K>;
+			clock-names = "iahb", "isfr", "tmds", "cec";
 			resets = <&ccu RST_BUS_HDMI1>;
 			reset-names = "ctrl";
 			phys = <&hdmi_phy>;
diff --git a/arch/arm/boot/dts/sun8i-t3-cqa3t-bv3.dts b/arch/arm/boot/dts/sun8i-t3-cqa3t-bv3.dts
index 6931aaab2382..9f472521f4a4 100644
--- a/arch/arm/boot/dts/sun8i-t3-cqa3t-bv3.dts
+++ b/arch/arm/boot/dts/sun8i-t3-cqa3t-bv3.dts
@@ -45,6 +45,7 @@
 
 /dts-v1/;
 #include "sun8i-r40.dtsi"
+#include "sun8i-r40-cpu-opp.dtsi"
 
 #include <dt-bindings/gpio/gpio.h>
 
@@ -88,6 +89,10 @@
 	status = "okay";
 };
 
+&cpu0 {
+	cpu-supply = <&reg_dcdc2>;
+};
+
 &de {
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/sun8i-v3s.dtsi b/arch/arm/boot/dts/sun8i-v3s.dtsi
index b30bc1a25ebb..db194c606fdc 100644
--- a/arch/arm/boot/dts/sun8i-v3s.dtsi
+++ b/arch/arm/boot/dts/sun8i-v3s.dtsi
@@ -42,6 +42,7 @@
  */
 
 #include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/sun6i-rtc.h>
 #include <dt-bindings/clock/sun8i-v3s-ccu.h>
 #include <dt-bindings/reset/sun8i-v3s-ccu.h>
 #include <dt-bindings/clock/sun8i-de2.h>
@@ -321,7 +322,7 @@
 		ccu: clock@1c20000 {
 			compatible = "allwinner,sun8i-v3s-ccu";
 			reg = <0x01c20000 0x400>;
-			clocks = <&osc24M>, <&rtc 0>;
+			clocks = <&osc24M>, <&rtc CLK_OSC32K>;
 			clock-names = "hosc", "losc";
 			#clock-cells = <1>;
 			#reset-cells = <1>;
@@ -342,7 +343,8 @@
 			reg = <0x01c20800 0x400>;
 			interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&ccu CLK_BUS_PIO>, <&osc24M>, <&rtc 0>;
+			clocks = <&ccu CLK_BUS_PIO>, <&osc24M>,
+				 <&rtc CLK_OSC32K>;
 			clock-names = "apb", "hosc", "losc";
 			gpio-controller;
 			#gpio-cells = <3>;
@@ -593,6 +595,17 @@
 			#size-cells = <0>;
 		};
 
+		gic: interrupt-controller@1c81000 {
+			compatible = "arm,gic-400";
+			reg = <0x01c81000 0x1000>,
+			      <0x01c82000 0x2000>,
+			      <0x01c84000 0x2000>,
+			      <0x01c86000 0x2000>;
+			interrupt-controller;
+			#interrupt-cells = <3>;
+			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+		};
+
 		csi1: camera@1cb4000 {
 			compatible = "allwinner,sun8i-v3s-csi";
 			reg = <0x01cb4000 0x3000>;
@@ -604,16 +617,5 @@
 			resets = <&ccu RST_BUS_CSI>;
 			status = "disabled";
 		};
-
-		gic: interrupt-controller@1c81000 {
-			compatible = "arm,gic-400";
-			reg = <0x01c81000 0x1000>,
-			      <0x01c82000 0x2000>,
-			      <0x01c84000 0x2000>,
-			      <0x01c86000 0x2000>;
-			interrupt-controller;
-			#interrupt-cells = <3>;
-			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
-		};
 	};
 };
diff --git a/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts b/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts
index 47954551f573..434871040aca 100644
--- a/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts
+++ b/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts
@@ -42,6 +42,7 @@
 
 /dts-v1/;
 #include "sun8i-r40.dtsi"
+#include "sun8i-r40-cpu-opp.dtsi"
 
 #include <dt-bindings/gpio/gpio.h>
 
@@ -107,6 +108,10 @@
 	status = "okay";
 };
 
+&cpu0 {
+	cpu-supply = <&reg_dcdc2>;
+};
+
 &de {
 	status = "okay";
 };
diff --git a/arch/arm/boot/dts/sun9i-a80.dtsi b/arch/arm/boot/dts/sun9i-a80.dtsi
index ce4fa6706d06..7d3f3300f431 100644
--- a/arch/arm/boot/dts/sun9i-a80.dtsi
+++ b/arch/arm/boot/dts/sun9i-a80.dtsi
@@ -1218,7 +1218,6 @@
 				     <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&apbs_gates 0>, <&osc24M>, <&osc32k>;
 			clock-names = "apb", "hosc", "losc";
-			resets = <&apbs_rst 0>;
 			gpio-controller;
 			interrupt-controller;
 			#interrupt-cells = <3>;
diff --git a/arch/arm/boot/dts/suniv-f1c100s-licheepi-nano.dts b/arch/arm/boot/dts/suniv-f1c100s-licheepi-nano.dts
index a1154e6c7cb5..04e59b8381cb 100644
--- a/arch/arm/boot/dts/suniv-f1c100s-licheepi-nano.dts
+++ b/arch/arm/boot/dts/suniv-f1c100s-licheepi-nano.dts
@@ -11,12 +11,43 @@
 	compatible = "licheepi,licheepi-nano", "allwinner,suniv-f1c100s";
 
 	aliases {
+		mmc0 = &mmc0;
 		serial0 = &uart0;
+		spi0 = &spi0;
 	};
 
 	chosen {
 		stdout-path = "serial0:115200n8";
 	};
+
+	reg_vcc3v3: vcc3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+};
+
+&mmc0 {
+	broken-cd;
+	bus-width = <4>;
+	disable-wp;
+	status = "okay";
+	vmmc-supply = <&reg_vcc3v3>;
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_pc_pins>;
+	status = "okay";
+
+	flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "winbond,w25q128", "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <40000000>;
+	};
 };
 
 &uart0 {
diff --git a/arch/arm/boot/dts/suniv-f1c100s.dtsi b/arch/arm/boot/dts/suniv-f1c100s.dtsi
index 6100d3b75f61..0edc1724407b 100644
--- a/arch/arm/boot/dts/suniv-f1c100s.dtsi
+++ b/arch/arm/boot/dts/suniv-f1c100s.dtsi
@@ -4,6 +4,9 @@
  * Copyright 2018 Mesih Kilinc <mesihkilinc@gmail.com>
  */
 
+#include <dt-bindings/clock/suniv-ccu-f1c100s.h>
+#include <dt-bindings/reset/suniv-ccu-f1c100s.h>
+
 / {
 	#address-cells = <1>;
 	#size-cells = <1>;
@@ -26,9 +29,13 @@
 	};
 
 	cpus {
-		cpu {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu@0 {
 			compatible = "arm,arm926ej-s";
 			device_type = "cpu";
+			reg = <0x0>;
 		};
 	};
 
@@ -62,6 +69,70 @@
 			};
 		};
 
+		spi0: spi@1c05000 {
+			compatible = "allwinner,suniv-f1c100s-spi",
+				     "allwinner,sun8i-h3-spi";
+			reg = <0x01c05000 0x1000>;
+			interrupts = <10>;
+			clocks = <&ccu CLK_BUS_SPI0>, <&ccu CLK_BUS_SPI0>;
+			clock-names = "ahb", "mod";
+			resets = <&ccu RST_BUS_SPI0>;
+			status = "disabled";
+			num-cs = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		spi1: spi@1c06000 {
+			compatible = "allwinner,suniv-f1c100s-spi",
+				     "allwinner,sun8i-h3-spi";
+			reg = <0x01c06000 0x1000>;
+			interrupts = <11>;
+			clocks = <&ccu CLK_BUS_SPI1>, <&ccu CLK_BUS_SPI1>;
+			clock-names = "ahb", "mod";
+			resets = <&ccu RST_BUS_SPI1>;
+			status = "disabled";
+			num-cs = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		mmc0: mmc@1c0f000 {
+			compatible = "allwinner,suniv-f1c100s-mmc",
+				     "allwinner,sun7i-a20-mmc";
+			reg = <0x01c0f000 0x1000>;
+			clocks = <&ccu CLK_BUS_MMC0>,
+				 <&ccu CLK_MMC0>,
+				 <&ccu CLK_MMC0_OUTPUT>,
+				 <&ccu CLK_MMC0_SAMPLE>;
+			clock-names = "ahb", "mmc", "output", "sample";
+			resets = <&ccu RST_BUS_MMC0>;
+			reset-names = "ahb";
+			interrupts = <23>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&mmc0_pins>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		mmc1: mmc@1c10000 {
+			compatible = "allwinner,suniv-f1c100s-mmc",
+				     "allwinner,sun7i-a20-mmc";
+			reg = <0x01c10000 0x1000>;
+			clocks = <&ccu CLK_BUS_MMC1>,
+				 <&ccu CLK_MMC1>,
+				 <&ccu CLK_MMC1_OUTPUT>,
+				 <&ccu CLK_MMC1_SAMPLE>;
+			clock-names = "ahb", "mmc", "output", "sample";
+			resets = <&ccu RST_BUS_MMC1>;
+			reset-names = "ahb";
+			interrupts = <24>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
 		ccu: clock@1c20000 {
 			compatible = "allwinner,suniv-f1c100s-ccu";
 			reg = <0x01c20000 0x400>;
@@ -82,13 +153,24 @@
 			compatible = "allwinner,suniv-f1c100s-pinctrl";
 			reg = <0x01c20800 0x400>;
 			interrupts = <38>, <39>, <40>;
-			clocks = <&ccu 37>, <&osc24M>, <&osc32k>;
+			clocks = <&ccu CLK_BUS_PIO>, <&osc24M>, <&osc32k>;
 			clock-names = "apb", "hosc", "losc";
 			gpio-controller;
 			interrupt-controller;
 			#interrupt-cells = <3>;
 			#gpio-cells = <3>;
 
+			mmc0_pins: mmc0-pins {
+				pins = "PF0", "PF1", "PF2", "PF3", "PF4", "PF5";
+				function = "mmc0";
+				drive-strength = <30>;
+			};
+
+			spi0_pc_pins: spi0-pc-pins {
+				pins = "PC0", "PC1", "PC2", "PC3";
+				function = "spi0";
+			};
+
 			uart0_pe_pins: uart0-pe-pins {
 				pins = "PE0", "PE1";
 				function = "uart0";
@@ -98,14 +180,16 @@
 		timer@1c20c00 {
 			compatible = "allwinner,suniv-f1c100s-timer";
 			reg = <0x01c20c00 0x90>;
-			interrupts = <13>;
+			interrupts = <13>, <14>, <15>;
 			clocks = <&osc24M>;
 		};
 
 		wdt: watchdog@1c20ca0 {
 			compatible = "allwinner,suniv-f1c100s-wdt",
-				     "allwinner,sun4i-a10-wdt";
+				     "allwinner,sun6i-a31-wdt";
 			reg = <0x01c20ca0 0x20>;
+			interrupts = <16>;
+			clocks = <&osc32k>;
 		};
 
 		uart0: serial@1c25000 {
@@ -114,8 +198,8 @@
 			interrupts = <1>;
 			reg-shift = <2>;
 			reg-io-width = <4>;
-			clocks = <&ccu 38>;
-			resets = <&ccu 24>;
+			clocks = <&ccu CLK_BUS_UART0>;
+			resets = <&ccu RST_BUS_UART0>;
 			status = "disabled";
 		};
 
@@ -125,8 +209,8 @@
 			interrupts = <2>;
 			reg-shift = <2>;
 			reg-io-width = <4>;
-			clocks = <&ccu 39>;
-			resets = <&ccu 25>;
+			clocks = <&ccu CLK_BUS_UART1>;
+			resets = <&ccu RST_BUS_UART1>;
 			status = "disabled";
 		};
 
@@ -136,8 +220,8 @@
 			interrupts = <3>;
 			reg-shift = <2>;
 			reg-io-width = <4>;
-			clocks = <&ccu 40>;
-			resets = <&ccu 26>;
+			clocks = <&ccu CLK_BUS_UART2>;
+			resets = <&ccu RST_BUS_UART2>;
 			status = "disabled";
 		};
 	};
diff --git a/arch/arm/boot/dts/sunplus-sp7021-achip.dtsi b/arch/arm/boot/dts/sunplus-sp7021-achip.dtsi
new file mode 100644
index 000000000000..493d32357e4e
--- /dev/null
+++ b/arch/arm/boot/dts/sunplus-sp7021-achip.dtsi
@@ -0,0 +1,84 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device Tree Source for Sunplus SP7021
+ *
+ * Copyright (C) 2021 Sunplus Technology Co.
+ */
+
+#include "sunplus-sp7021.dtsi"
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+	compatible = "sunplus,sp7021-achip", "sunplus,sp7021";
+	model = "Sunplus SP7021 (CA7)";
+	#address-cells = <1>;
+	#size-cells = <1>;
+	interrupt-parent = <&gic>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			compatible = "arm,cortex-a7";
+			device_type = "cpu";
+			reg = <0>;
+			clock-frequency = <931000000>;
+		};
+		cpu1: cpu@1 {
+			compatible = "arm,cortex-a7";
+			device_type = "cpu";
+			reg = <1>;
+			clock-frequency = <931000000>;
+		};
+		cpu2: cpu@2 {
+			compatible = "arm,cortex-a7";
+			device_type = "cpu";
+			reg = <2>;
+			clock-frequency = <931000000>;
+		};
+		cpu3: cpu@3 {
+			compatible = "arm,cortex-a7";
+			device_type = "cpu";
+			reg = <3>;
+			clock-frequency = <931000000>;
+		};
+	};
+
+	gic: interrupt-controller@9f101000 {
+		compatible = "arm,cortex-a7-gic";
+		interrupt-controller;
+		#interrupt-cells = <3>;
+		reg = <0x9f101000 0x1000>,
+		      <0x9f102000 0x2000>,
+		      <0x9f104000 0x2000>,
+		      <0x9f106000 0x2000>;
+	};
+
+	timer {
+		compatible = "arm,armv7-timer";
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+		clock-frequency = <XTAL>;
+		arm,cpu-registers-not-fw-configured;
+	};
+
+	arm-pmu {
+		compatible = "arm,cortex-a7-pmu";
+		interrupts = <GIC_SPI 219 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 221 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 222 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>;
+	};
+
+	soc@9c000000 {
+		intc: interrupt-controller@780 {
+			interrupt-parent = <&gic>;
+			interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>, /* EXT_INT0 */
+				     <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>; /* EXT_INT1 */
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/sunplus-sp7021-demo-v3.dts b/arch/arm/boot/dts/sunplus-sp7021-demo-v3.dts
new file mode 100644
index 000000000000..d5c5ffc20565
--- /dev/null
+++ b/arch/arm/boot/dts/sunplus-sp7021-demo-v3.dts
@@ -0,0 +1,30 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device Tree Source for Sunplus SP7021 Demo V3 SBC board
+ *
+ * Copyright (C) Sunplus Technology Co.
+ */
+
+/dts-v1/;
+
+#include "sunplus-sp7021-achip.dtsi"
+
+/ {
+	compatible = "sunplus,sp7021-demo-v3", "sunplus,sp7021";
+	model = "Sunplus SP7021/CA7/Demo_V3";
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x20000000>;
+	};
+};
diff --git a/arch/arm/boot/dts/sunplus-sp7021.dtsi b/arch/arm/boot/dts/sunplus-sp7021.dtsi
new file mode 100644
index 000000000000..7dc4ce3619c7
--- /dev/null
+++ b/arch/arm/boot/dts/sunplus-sp7021.dtsi
@@ -0,0 +1,310 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device Tree Source for Sunplus SP7021
+ *
+ * Copyright (C) 2021 Sunplus Technology Co.
+ */
+
+#include <dt-bindings/clock/sunplus,sp7021-clkc.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/reset/sunplus,sp7021-reset.h>
+#include <dt-bindings/pinctrl/sppctl-sp7021.h>
+#include <dt-bindings/gpio/gpio.h>
+
+#define XTAL	27000000
+
+/ {
+	compatible = "sunplus,sp7021";
+	model = "Sunplus SP7021";
+
+	clocks {
+		extclk: osc0 {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <XTAL>;
+			clock-output-names = "extclk";
+		};
+	};
+
+	soc@9c000000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0x9c000000 0x400000>;
+		interrupt-parent = <&intc>;
+
+		clkc: clock-controller@4 {
+			compatible = "sunplus,sp7021-clkc";
+			reg = <0x4 0x28>,
+			      <0x200 0x44>,
+			      <0x268 0x04>;
+			clocks = <&extclk>;
+			#clock-cells = <1>;
+		};
+
+		intc: interrupt-controller@780 {
+			compatible = "sunplus,sp7021-intc";
+			reg = <0x780 0x80>, <0xa80 0x80>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		otp: otp@af00 {
+			compatible = "sunplus,sp7021-ocotp";
+			reg = <0xaf00 0x34>, <0xaf80 0x58>;
+			reg-names = "hb_gpio", "otprx";
+			clocks = <&clkc CLK_OTPRX>;
+			resets = <&rstc RST_OTPRX>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			therm_calib: thermal-calibration@14 {
+				reg = <0x14 0x3>;
+			};
+			disc_vol: disconnect-voltage@18 {
+				reg = <0x18 0x2>;
+			};
+			mac_addr0: mac-address0@34 {
+				reg = <0x34 0x6>;
+			};
+			mac_addr1: mac-address1@3a {
+				reg = <0x3a 0x6>;
+			};
+		};
+
+		pctl: pinctrl@100 {
+			compatible = "sunplus,sp7021-pctl";
+			reg = <0x100 0x100>,
+			      <0x300 0x100>,
+			      <0x32e4 0x1C>,
+			      <0x80 0x20>;
+			reg-names = "moon2", "gpioxt", "first", "moon1";
+			gpio-controller;
+			#gpio-cells = <2>;
+			clocks = <&clkc CLK_GPIO>;
+			resets = <&rstc RST_GPIO>;
+
+			emac_pins: pinmux-emac-pins {
+				sunplus,pins = <
+					SPPCTL_IOPAD(49,SPPCTL_PCTL_G_PMUX,MUXF_L2SW_CLK_OUT,0)
+					SPPCTL_IOPAD(44,SPPCTL_PCTL_G_PMUX,MUXF_L2SW_MAC_SMI_MDC,0)
+					SPPCTL_IOPAD(43,SPPCTL_PCTL_G_PMUX,MUXF_L2SW_MAC_SMI_MDIO,0)
+					SPPCTL_IOPAD(52,SPPCTL_PCTL_G_PMUX,MUXF_L2SW_P0_MAC_RMII_TXEN,0)
+					SPPCTL_IOPAD(50,SPPCTL_PCTL_G_PMUX,MUXF_L2SW_P0_MAC_RMII_TXD0,0)
+					SPPCTL_IOPAD(51,SPPCTL_PCTL_G_PMUX,MUXF_L2SW_P0_MAC_RMII_TXD1,0)
+					SPPCTL_IOPAD(46,SPPCTL_PCTL_G_PMUX,MUXF_L2SW_P0_MAC_RMII_CRSDV,0)
+					SPPCTL_IOPAD(47,SPPCTL_PCTL_G_PMUX,MUXF_L2SW_P0_MAC_RMII_RXD0,0)
+					SPPCTL_IOPAD(48,SPPCTL_PCTL_G_PMUX,MUXF_L2SW_P0_MAC_RMII_RXD1,0)
+					SPPCTL_IOPAD(45,SPPCTL_PCTL_G_PMUX,MUXF_L2SW_P0_MAC_RMII_RXER,0)
+					SPPCTL_IOPAD(59,SPPCTL_PCTL_G_PMUX,MUXF_L2SW_P1_MAC_RMII_TXEN,0)
+					SPPCTL_IOPAD(57,SPPCTL_PCTL_G_PMUX,MUXF_L2SW_P1_MAC_RMII_TXD0,0)
+					SPPCTL_IOPAD(58,SPPCTL_PCTL_G_PMUX,MUXF_L2SW_P1_MAC_RMII_TXD1,0)
+					SPPCTL_IOPAD(54,SPPCTL_PCTL_G_PMUX,MUXF_L2SW_P1_MAC_RMII_CRSDV,0)
+					SPPCTL_IOPAD(55,SPPCTL_PCTL_G_PMUX,MUXF_L2SW_P1_MAC_RMII_RXD0,0)
+					SPPCTL_IOPAD(56,SPPCTL_PCTL_G_PMUX,MUXF_L2SW_P1_MAC_RMII_RXD1,0)
+					SPPCTL_IOPAD(53,SPPCTL_PCTL_G_PMUX,MUXF_L2SW_P1_MAC_RMII_RXER,0)
+				>;
+				sunplus,zerofunc = <
+					MUXF_L2SW_LED_FLASH0
+					MUXF_L2SW_LED_FLASH1
+					MUXF_L2SW_LED_ON0
+					MUXF_L2SW_LED_ON1
+					MUXF_DAISY_MODE
+				>;
+			};
+
+			emmc_pins: pinmux-emmc-pins {
+				function = "CARD0_EMMC";
+				groups = "CARD0_EMMC";
+			};
+
+			leds_pins: pinmux-leds-pins {
+				sunplus,pins = < SPPCTL_IOPAD(0,SPPCTL_PCTL_G_GPIO,0,SPPCTL_PCTL_L_OUT) >;
+			};
+
+			sdcard_pins: pinmux-sdcard-pins {
+				function = "SD_CARD";
+				groups = "SD_CARD";
+				sunplus,pins = < SPPCTL_IOPAD(91, SPPCTL_PCTL_G_GPIO, 0, 0) >;
+			};
+
+			spi0_pins: pinmux-spi0-pins {
+				sunplus,pins = <
+					SPPCTL_IOPAD(26,SPPCTL_PCTL_G_GPIO,0,0)
+					SPPCTL_IOPAD(28,SPPCTL_PCTL_G_GPIO,0,0)
+					SPPCTL_IOPAD(23,SPPCTL_PCTL_G_PMUX,MUXF_SPI0S_DO,0)
+					SPPCTL_IOPAD(25,SPPCTL_PCTL_G_PMUX,MUXF_SPI0S_DI,0)
+					SPPCTL_IOPAD(27,SPPCTL_PCTL_G_PMUX,MUXF_SPI0S_CLK,0)
+				>;
+			};
+
+			uart0_pins: pinmux-uart0-pins {
+				function = "UA0";
+				groups = "UA0";
+			};
+
+			uart1_pins: pinmux-uart1-pins {
+				sunplus,pins = <
+					SPPCTL_IOPAD(14,SPPCTL_PCTL_G_PMUX,MUXF_UA4_TX,0)
+					SPPCTL_IOPAD(16,SPPCTL_PCTL_G_PMUX,MUXF_UA4_RX,0)
+				>;
+			};
+
+			uart2_pins: pinmux-uart2-pins {
+				sunplus,pins = <
+					SPPCTL_IOPAD(16,SPPCTL_PCTL_G_PMUX,MUXF_UA2_TX,0)
+					SPPCTL_IOPAD(17,SPPCTL_PCTL_G_PMUX,MUXF_UA2_RX,0)
+					SPPCTL_IOPAD(18,SPPCTL_PCTL_G_PMUX,MUXF_UA2_RTS,0)
+					SPPCTL_IOPAD(19,SPPCTL_PCTL_G_PMUX,MUXF_UA2_CTS,0)
+				>;
+			};
+
+			uart4_pins: pinmux-uart4-pins {
+				sunplus,pins = <
+					SPPCTL_IOPAD(22,SPPCTL_PCTL_G_PMUX,MUXF_UA4_TX,0)
+					SPPCTL_IOPAD(20,SPPCTL_PCTL_G_PMUX,MUXF_UA4_RX,0)
+					SPPCTL_IOPAD(23,SPPCTL_PCTL_G_PMUX,MUXF_UA4_RTS,0)
+					SPPCTL_IOPAD(21,SPPCTL_PCTL_G_PMUX,MUXF_UA4_CTS,0)
+				>;
+			};
+		};
+
+		rstc: reset@54 {
+			compatible = "sunplus,sp7021-reset";
+			reg = <0x54 0x28>;
+			#reset-cells = <1>;
+		};
+
+		rtc: rtc@3a00 {
+			compatible = "sunplus,sp7021-rtc";
+			reg = <0x3a00 0x80>;
+			reg-names = "rtc";
+			clocks = <&clkc CLK_RTC>;
+			resets = <&rstc RST_RTC>;
+			interrupts = <163 IRQ_TYPE_EDGE_RISING>;
+		};
+
+		spi_controller0: spi@2d80 {
+			compatible = "sunplus,sp7021-spi";
+			reg = <0x2d80 0x80>, <0x2e00 0x80>;
+			reg-names = "master", "slave";
+			interrupts = <144 IRQ_TYPE_LEVEL_HIGH>,
+				     <146 IRQ_TYPE_LEVEL_HIGH>,
+				     <145 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "dma_w", "master_risc", "slave_risc";
+			clocks = <&clkc CLK_SPI_COMBO_0>;
+			resets = <&rstc RST_SPI_COMBO_0>;
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&spi0_pins>;
+			cs-gpios = <&pctl 26 GPIO_ACTIVE_LOW>,
+				   <&pctl 28 GPIO_ACTIVE_LOW>;
+		};
+
+		spi_controller1: spi@f480 {
+			compatible = "sunplus,sp7021-spi";
+			reg = <0xf480 0x80>, <0xf500 0x80>;
+			reg-names = "master", "slave";
+			interrupts = <67 IRQ_TYPE_LEVEL_HIGH>,
+				     <69 IRQ_TYPE_LEVEL_HIGH>,
+				     <68 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "dma_w", "master_risc", "slave_risc";
+			clocks = <&clkc CLK_SPI_COMBO_1>;
+			resets = <&rstc RST_SPI_COMBO_1>;
+			spi-max-frequency = <25000000>;
+			status = "disabled";
+		};
+
+		spi_controller2: spi@f600 {
+			compatible = "sunplus,sp7021-spi";
+			reg = <0xf600 0x80>, <0xf680 0x80>;
+			reg-names = "master", "slave";
+			interrupts = <70 IRQ_TYPE_LEVEL_HIGH>,
+				     <72 IRQ_TYPE_LEVEL_HIGH>,
+				     <71 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "dma_w", "master_risc", "slave_risc";
+			clocks = <&clkc CLK_SPI_COMBO_2>;
+			resets = <&rstc RST_SPI_COMBO_2>;
+			spi-max-frequency = <25000000>;
+			status = "disabled";
+		};
+
+		spi_controller3: spi@f780 {
+			compatible = "sunplus,sp7021-spi";
+			reg = <0xf780 0x80>, <0xf800 0x80>;
+			reg-names = "master", "slave";
+			interrupts = <73 IRQ_TYPE_LEVEL_HIGH>,
+				     <75 IRQ_TYPE_LEVEL_HIGH>,
+				     <74 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "dma_w", "master_risc", "slave_risc";
+			clocks = <&clkc CLK_SPI_COMBO_3>;
+			resets = <&rstc RST_SPI_COMBO_3>;
+			spi-max-frequency = <25000000>;
+			status = "disabled";
+		};
+
+		uart0: serial@900 {
+			compatible = "sunplus,sp7021-uart";
+			reg = <0x900 0x80>;
+			interrupts = <53 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clkc CLK_UA0>;
+			resets = <&rstc RST_UA0>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&uart0_pins>;
+		};
+
+		uart1: serial@980 {
+			compatible = "sunplus,sp7021-uart";
+			reg = <0x980 0x80>;
+			interrupts = <54 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clkc CLK_UA1>;
+			resets = <&rstc RST_UA1>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&uart1_pins>;
+			status = "disabled";
+		};
+
+		uart2: serial@800 {
+			compatible = "sunplus,sp7021-uart";
+			reg = <0x800 0x80>;
+			interrupts = <55 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clkc CLK_UA2>;
+			resets = <&rstc RST_UA2>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&uart2_pins>;
+			status = "disabled";
+		};
+
+		uart3: serial@880 {
+			compatible = "sunplus,sp7021-uart";
+			reg = <0x880 0x80>;
+			interrupts = <56 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clkc CLK_UA3>;
+			resets = <&rstc RST_UA3>;
+			status = "disabled";
+		};
+
+		uart4: serial@8780 {
+			compatible = "sunplus,sp7021-uart";
+			reg = <0x8780 0x80>;
+			interrupts = <134 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clkc CLK_UA4>;
+			resets = <&rstc RST_UA4>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&uart4_pins>;
+			status = "disabled";
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&leds_pins>;
+		system-led {
+			label = "system-led";
+			gpios = <&pctl 0 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+			linux,default-trigger = "heartbeat";
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/sunxi-bananapi-m2-plus.dtsi b/arch/arm/boot/dts/sunxi-bananapi-m2-plus.dtsi
index 7a6af54dd342..e899d14f38c3 100644
--- a/arch/arm/boot/dts/sunxi-bananapi-m2-plus.dtsi
+++ b/arch/arm/boot/dts/sunxi-bananapi-m2-plus.dtsi
@@ -77,13 +77,14 @@
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
-		sw4 {
+		switch-4 {
 			label = "power";
-			linux,code = <BTN_0>;
+			linux,code = <KEY_POWER>;
 			gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
+			wakeup-source;
 		};
 	};
 
@@ -100,7 +101,7 @@
 	wifi_pwrseq: wifi_pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
-		clocks = <&rtc 1>;
+		clocks = <&rtc CLK_OSC32K_FANOUT>;
 		clock-names = "ext_clock";
 	};
 };
@@ -220,7 +221,7 @@
 	bluetooth {
 		compatible = "brcm,bcm43438-bt";
 		max-speed = <1500000>;
-		clocks = <&rtc 1>;
+		clocks = <&rtc CLK_OSC32K_FANOUT>;
 		clock-names = "lpo";
 		vbat-supply = <&reg_vcc3v3>;
 		vddio-supply = <&reg_vcc3v3>;
diff --git a/arch/arm/boot/dts/sunxi-h3-h5-emlid-neutis.dtsi b/arch/arm/boot/dts/sunxi-h3-h5-emlid-neutis.dtsi
index fc67e30fe212..60804b0e6c56 100644
--- a/arch/arm/boot/dts/sunxi-h3-h5-emlid-neutis.dtsi
+++ b/arch/arm/boot/dts/sunxi-h3-h5-emlid-neutis.dtsi
@@ -22,7 +22,7 @@
 		compatible = "mmc-pwrseq-simple";
 		reset-gpios = <&pio 2 7 GPIO_ACTIVE_LOW>; /* PC7 */
 		post-power-on-delay-ms = <200>;
-		clocks = <&rtc 1>;
+		clocks = <&rtc CLK_OSC32K_FANOUT>;
 		clock-names = "ext_clock";
 	};
 };
@@ -124,7 +124,7 @@
 
 	bluetooth {
 		compatible = "brcm,bcm43438-bt";
-		clocks = <&rtc 1>;
+		clocks = <&rtc CLK_OSC32K_FANOUT>;
 		clock-names = "lpo";
 		vbat-supply = <&reg_vcc3v3>;
 		vddio-supply = <&reg_vcc3v3>;
diff --git a/arch/arm/boot/dts/sunxi-h3-h5.dtsi b/arch/arm/boot/dts/sunxi-h3-h5.dtsi
index c7428df9469e..09aefb4e90f8 100644
--- a/arch/arm/boot/dts/sunxi-h3-h5.dtsi
+++ b/arch/arm/boot/dts/sunxi-h3-h5.dtsi
@@ -40,6 +40,7 @@
  *     OTHER DEALINGS IN THE SOFTWARE.
  */
 
+#include <dt-bindings/clock/sun6i-rtc.h>
 #include <dt-bindings/clock/sun8i-de2.h>
 #include <dt-bindings/clock/sun8i-h3-ccu.h>
 #include <dt-bindings/clock/sun8i-r-ccu.h>
@@ -386,7 +387,7 @@
 		ccu: clock@1c20000 {
 			/* compatible is in per SoC .dtsi file */
 			reg = <0x01c20000 0x400>;
-			clocks = <&osc24M>, <&rtc 0>;
+			clocks = <&osc24M>, <&rtc CLK_OSC32K>;
 			clock-names = "hosc", "losc";
 			#clock-cells = <1>;
 			#reset-cells = <1>;
@@ -398,7 +399,8 @@
 			interrupt-parent = <&r_intc>;
 			interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&ccu CLK_BUS_PIO>, <&osc24M>, <&rtc 0>;
+			clocks = <&ccu CLK_BUS_PIO>, <&osc24M>,
+				 <&rtc CLK_OSC32K>;
 			clock-names = "apb", "hosc", "losc";
 			gpio-controller;
 			#gpio-cells = <3>;
@@ -568,9 +570,14 @@
 		};
 
 		mbus: dram-controller@1c62000 {
-			compatible = "allwinner,sun8i-h3-mbus";
-			reg = <0x01c62000 0x1000>;
-			clocks = <&ccu CLK_MBUS>;
+			/* compatible is in per SoC .dtsi file */
+			reg = <0x01c62000 0x1000>,
+			      <0x01c63000 0x1000>;
+			reg-names = "mbus", "dram";
+			clocks = <&ccu CLK_MBUS>,
+				 <&ccu CLK_DRAM>,
+				 <&ccu CLK_BUS_DRAM>;
+			clock-names = "mbus", "dram", "bus";
 			#address-cells = <1>;
 			#size-cells = <1>;
 			dma-ranges = <0x00000000 0x40000000 0xc0000000>;
@@ -813,8 +820,8 @@
 			reg-io-width = <1>;
 			interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&ccu CLK_BUS_HDMI>, <&ccu CLK_HDMI_DDC>,
-				 <&ccu CLK_HDMI>;
-			clock-names = "iahb", "isfr", "tmds";
+				 <&ccu CLK_HDMI>, <&rtc CLK_OSC32K>;
+			clock-names = "iahb", "isfr", "tmds", "cec";
 			resets = <&ccu RST_BUS_HDMI1>;
 			reset-names = "ctrl";
 			phys = <&hdmi_phy>;
@@ -873,7 +880,7 @@
 		r_ccu: clock@1f01400 {
 			compatible = "allwinner,sun8i-h3-r-ccu";
 			reg = <0x01f01400 0x100>;
-			clocks = <&osc24M>, <&rtc 0>, <&rtc 2>,
+			clocks = <&osc24M>, <&rtc CLK_OSC32K>, <&rtc CLK_IOSC>,
 				 <&ccu CLK_PLL_PERIPH0>;
 			clock-names = "hosc", "losc", "iosc", "pll-periph";
 			#clock-cells = <1>;
@@ -908,12 +915,26 @@
 			#size-cells = <0>;
 		};
 
+		r_uart: serial@1f02800 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x01f02800 0x400>;
+			interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&r_ccu CLK_APB0_UART>;
+			resets = <&r_ccu RST_APB0_UART>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&r_uart_pins>;
+			status = "disabled";
+		};
+
 		r_pio: pinctrl@1f02c00 {
 			compatible = "allwinner,sun8i-h3-r-pinctrl";
 			reg = <0x01f02c00 0x400>;
 			interrupt-parent = <&r_intc>;
 			interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&r_ccu CLK_APB0_PIO>, <&osc24M>, <&rtc 0>;
+			clocks = <&r_ccu CLK_APB0_PIO>, <&osc24M>,
+				 <&rtc CLK_OSC32K>;
 			clock-names = "apb", "hosc", "losc";
 			gpio-controller;
 			#gpio-cells = <3>;
@@ -934,6 +955,11 @@
 				pins = "PL10";
 				function = "s_pwm";
 			};
+
+			r_uart_pins: r-uart-pins {
+				pins = "PL2", "PL3";
+				function = "s_uart";
+			};
 		};
 
 		r_pwm: pwm@1f03800 {
diff --git a/arch/arm/boot/dts/sunxi-libretech-all-h3-cc.dtsi b/arch/arm/boot/dts/sunxi-libretech-all-h3-cc.dtsi
index c44fd726945a..89731bb34c6b 100644
--- a/arch/arm/boot/dts/sunxi-libretech-all-h3-cc.dtsi
+++ b/arch/arm/boot/dts/sunxi-libretech-all-h3-cc.dtsi
@@ -42,13 +42,14 @@
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
-		power {
+		key-power {
 			label = "power";
 			linux,code = <KEY_POWER>;
 			gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */
+			wakeup-source;
 		};
 	};
 
diff --git a/arch/arm/boot/dts/tegra114-asus-tf701t.dts b/arch/arm/boot/dts/tegra114-asus-tf701t.dts
new file mode 100644
index 000000000000..284209b0bd96
--- /dev/null
+++ b/arch/arm/boot/dts/tegra114-asus-tf701t.dts
@@ -0,0 +1,807 @@
+// SPDX-License-Identifier: GPL-2.0
+
+/dts-v1/;
+
+#include <dt-bindings/input/gpio-keys.h>
+#include <dt-bindings/input/input.h>
+
+#include "tegra114.dtsi"
+
+/ {
+	model = "Asus Transformer Pad TF701T";
+	compatible = "asus,tf701t", "nvidia,tegra114";
+	chassis-type = "convertible";
+
+	aliases {
+		mmc0 = "/mmc@78000600"; /* eMMC */
+		mmc1 = "/mmc@78000400"; /* uSD slot */
+		mmc2 = "/mmc@78000000"; /* WiFi */
+
+		rtc0 = &palmas;
+		rtc1 = "/rtc@7000e000";
+
+		serial0 = &uartd; /* Console */
+		serial1 = &uartc; /* Bluetooth */
+		serial2 = &uartb; /* GPS */
+	};
+
+	memory@80000000 {
+		reg = <0x80000000 0x80000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		linux,cma@80000000 {
+			compatible = "shared-dma-pool";
+			alloc-ranges = <0x80000000 0x30000000>;
+			size = <0x10000000>;
+			linux,cma-default;
+			reusable;
+		};
+
+		trustzone@bfe00000 {
+			reg = <0xbfe00000 0x200000>;
+			no-map;
+		};
+	};
+
+	host1x@50000000 {
+		dsi@54300000 {
+			status = "okay";
+
+			avdd-dsi-csi-supply = <&tps65913_ldo2>;
+
+			nvidia,ganged-mode = <&dsib>;
+
+			panel_primary: panel@0 {
+				compatible = "sharp,lq101r1sx01";
+				reg = <0>;
+
+				link2 = <&panel_secondary>;
+
+				power-supply = <&vdd_lcd>;
+				backlight = <&backlight>;
+			};
+		};
+
+		dsi@54400000 {
+			status = "okay";
+
+			avdd-dsi-csi-supply = <&tps65913_ldo2>;
+
+			panel_secondary: panel@0 {
+				compatible = "sharp,lq101r1sx01";
+				reg = <0>;
+			};
+		};
+	};
+
+	pinmux@70000868 {
+		asus_pad_ec_default: asus-pad-ec-default {
+			ec-interrupt {
+				nvidia,pins = "kb_col5_pq5";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			ec-request {
+				nvidia,pins = "kb_col2_pq2";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+		};
+
+		backlight_default: backlight-default {
+			backlight-enable {
+				nvidia,pins = "gmi_ad10_ph2";
+				nvidia,function = "gmi";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+		};
+
+		codec_default: codec-default {
+			ldo1-en {
+				nvidia,pins = "sdmmc1_wp_n_pv3";
+				nvidia,function = "sdmmc1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			interrupt {
+				nvidia,pins = "gpio_w2_aud_pw2",
+						"gpio_w3_aud_pw3";
+				nvidia,function = "spi6";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+		};
+
+		gpio_keys_default: gpio-keys-default {
+			power {
+				nvidia,pins = "kb_col0_pq0";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			volume {
+				nvidia,pins = "kb_row1_pr1",
+						"kb_row2_pr2";
+				nvidia,function = "rsvd2";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+		};
+
+		gpio_hall_sensor_default: gpio-hall-sensor-default {
+			ulpi_data4_po5 {
+				nvidia,pins = "ulpi_data4_po5";
+				nvidia,function = "spi2";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+		};
+
+		hp_det_default: hp-det-default {
+			gmi_iordy_pi5 {
+				nvidia,pins = "kb_row7_pr7";
+				nvidia,function = "rsvd2";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+		};
+
+		imu_default: imu-default {
+			kb_row3_pr3 {
+				nvidia,pins = "kb_row3_pr3";
+				nvidia,function = "rsvd3";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+		};
+
+		pwm_default: pwm-default {
+			gmi_ad9_ph1 {
+				nvidia,pins = "gmi_ad9_ph1";
+				nvidia,function = "pwm1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+		};
+
+		/* XXX make this something more sensible */
+		pwm_sleep: pwm-sleep {
+			gmi_ad9_ph1 {
+				nvidia,pins = "gmi_ad9_ph1";
+				nvidia,function = "pwm1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+		};
+
+		sdmmc3_default: sdmmc3-default {
+			sdmmc3_clk_pa6 {
+				nvidia,pins = "sdmmc3_clk_pa6";
+				nvidia,function = "sdmmc3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			sdmmc3_cmd_pa7 {
+				nvidia,pins = "sdmmc3_cmd_pa7",
+						"sdmmc3_dat0_pb7",
+						"sdmmc3_dat1_pb6",
+						"sdmmc3_dat2_pb5",
+						"sdmmc3_dat3_pb4",
+						"kb_col4_pq4",
+						"sdmmc3_clk_lb_out_pee4",
+						"sdmmc3_clk_lb_in_pee5",
+						"sdmmc3_cd_n_pv2";
+				nvidia,function = "sdmmc3";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			drive_sdio3 {
+				nvidia,pins = "drive_sdio3";
+				nvidia,high-speed-mode = <TEGRA_PIN_ENABLE>;
+				nvidia,schmitt = <TEGRA_PIN_DISABLE>;
+				nvidia,pull-down-strength = <22>;
+				nvidia,pull-up-strength = <36>;
+				nvidia,slew-rate-rising = <TEGRA_PIN_SLEW_RATE_FASTEST>;
+				nvidia,slew-rate-falling = <TEGRA_PIN_SLEW_RATE_FASTEST>;
+			};
+		};
+
+		sdmmc3_vdd_default: sdmmc3-vdd-default {
+			gmi_clk_pk1 {
+				nvidia,pins = "gmi_clk_pk1";
+				nvidia,function = "gmi";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+		};
+
+		vdd_lcd_default: vdd-lcd-default {
+			sdmmc4_clk_pcc4 {
+				nvidia,pins = "sdmmc4_clk_pcc4";
+				nvidia,function = "sdmmc4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+		};
+	};
+
+	serial@70006040 {
+		/* GPS */
+	};
+
+	serial@70006200 {
+		/* Bluetooth */
+	};
+
+	serial@70006300 {
+		status = "okay";
+	};
+
+	pwm@7000a000 {
+		status = "okay";
+
+		pinctrl-names = "default", "sleep";
+		pinctrl-0 = <&pwm_default>;
+		pinctrl-1 = <&pwm_sleep>;
+	};
+
+	i2c@7000c000 {
+		status = "okay";
+		clock-frequency = <100000>;
+
+		magnetometer@c {
+			compatible = "asahi-kasei,ak09911";
+			reg = <0xc>;
+
+			vdd-supply = <&vdd_3v3_sys>;
+		};
+
+		rt5639: audio-codec@1c {
+			compatible = "realtek,rt5639";
+			reg = <0x1c>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(W, 3) IRQ_TYPE_EDGE_FALLING>;
+
+			realtek,ldo1-en-gpios = <&gpio TEGRA_GPIO(V, 3) GPIO_ACTIVE_HIGH>;
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&codec_default>;
+		};
+
+		motion-tracker@68 {
+			compatible = "invensense,mpu6500";
+			reg = <0x68>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(R, 3) IRQ_TYPE_LEVEL_HIGH>;
+
+			mount-matrix =  "0", "-1", "0",
+					"1",  "0", "0",
+					"0",  "0", "1";
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&imu_default>;
+		};
+
+		temp_sensor: temperature-sensor@4c {
+			compatible = "onnn,nct1008";
+			reg = <0x4c>;
+
+			vcc-supply = <&vdd_3v3_sys>;
+			#thermal-sensor-cells = <1>;
+		};
+	};
+
+	i2c@7000c400 {
+		status = "okay";
+		clock-frequency = <100000>;
+
+		power-sensor@44 {
+			compatible = "ti,ina230";
+			reg = <0x44>;
+		};
+	};
+
+	i2c@7000c500 {
+		status = "okay";
+		clock-frequency = <400000>;
+
+		light-sensor@1c {
+			compatible = "dynaimage,al3320a";
+			reg = <0x1c>;
+
+			vdd-supply = <&vdd_3v3_sys>;
+		};
+	};
+
+	i2c@7000c700 {
+		/* HDMI DDC */
+	};
+
+	i2c@7000d000 {
+		status = "okay";
+		clock-frequency = <400000>;
+
+		palmas: pmic@58 {
+			compatible = "ti,tps65913", "ti,palmas";
+			reg = <0x58>;
+			interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
+
+			#interrupt-cells = <2>;
+			interrupt-controller;
+
+			ti,system-power-controller;
+
+			palmas_gpio: gpio {
+				compatible = "ti,palmas-gpio";
+				gpio-controller;
+				#gpio-cells = <2>;
+			};
+
+			pmic {
+				compatible = "ti,tps65913-pmic", "ti,palmas-pmic";
+
+				ldo1-in-supply = <&tps65913_smps7>;
+				ldo2-in-supply = <&tps65913_smps7>;
+				ldo4-in-supply = <&tps65913_smps8>;
+				ldo5-in-supply = <&tps65913_smps9>;
+				ldo6-in-supply = <&tps65913_smps9>;
+				ldo7-in-supply = <&tps65913_smps9>;
+				ldo9-in-supply = <&tps65913_smps9>;
+
+				regulators {
+					tps65913_smps123: smps123 {
+						regulator-name = "vdd-cpu";
+						regulator-min-microvolt = <900000>;
+						regulator-max-microvolt = <1350000>;
+						regulator-always-on;
+						regulator-boot-on;
+						ti,roof-floor = <1>;
+						ti,mode-sleep = <3>;
+					};
+
+					tps65913_smps45: smps45 {
+						regulator-name = "vdd-core";
+						regulator-min-microvolt = <900000>;
+						regulator-max-microvolt = <1400000>;
+						regulator-always-on;
+						regulator-boot-on;
+						ti,roof-floor = <3>;
+					};
+
+					smps6 {
+						regulator-name = "va-lcd-hv";
+						regulator-min-microvolt = <1000000>;
+						regulator-max-microvolt = <1000000>;
+						regulator-always-on;
+						regulator-boot-on;
+					};
+
+					tps65913_smps7: smps7 {
+						regulator-name = "vdd-ddr";
+						regulator-min-microvolt = <1350000>;
+						regulator-max-microvolt = <1350000>;
+						regulator-always-on;
+						regulator-boot-on;
+					};
+
+					tps65913_smps8: smps8 {
+						regulator-name = "vdd-1v8";
+						regulator-min-microvolt = <1800000>;
+						regulator-max-microvolt = <1800000>;
+						regulator-always-on;
+						regulator-boot-on;
+					};
+
+					tps65913_smps9: smps9 {
+						regulator-name = "vdd-sd";
+						regulator-min-microvolt = <2900000>;
+						regulator-max-microvolt = <2900000>;
+						regulator-always-on;
+					};
+
+					tps65913_smps10_out1: smps10_out1 {
+						regulator-name = "vd-smps10-out1";
+						regulator-min-microvolt = <5000000>;
+						regulator-max-microvolt = <5000000>;
+						regulator-always-on;
+						regulator-boot-on;
+					};
+
+					tps65913_smps10_out2: smps10_out2 {
+						regulator-name = "vd-smps10-out2";
+						regulator-min-microvolt = <5000000>;
+						regulator-max-microvolt = <5000000>;
+						regulator-always-on;
+						regulator-boot-on;
+					};
+
+					tps65913_ldo1: ldo1 {
+						regulator-name = "vdd-hdmi-pll";
+						regulator-min-microvolt = <1050000>;
+						regulator-max-microvolt = <1050000>;
+						regulator-always-on;
+						ti,roof-floor = <3>;
+					};
+
+					tps65913_ldo2: ldo2 {
+						regulator-name = "vdd-2v8-dsi-csi";
+						regulator-min-microvolt = <1200000>;
+						regulator-max-microvolt = <1200000>;
+						regulator-boot-on;
+					};
+
+					ldo3 {
+						regulator-name = "vpp-fuse";
+						regulator-min-microvolt = <1800000>;
+						regulator-max-microvolt = <1800000>;
+					};
+
+					ldo4 {
+						regulator-name = "vdd-1v2-cam";
+						regulator-min-microvolt = <1200000>;
+						regulator-max-microvolt = <1200000>;
+					};
+
+					ldo5 {
+						regulator-name = "vdd-cam";
+						regulator-min-microvolt = <2800000>;
+						regulator-max-microvolt = <2800000>;
+					};
+
+					ldo6 {
+						regulator-name = "vdd-dev";
+						regulator-min-microvolt = <2850000>;
+						regulator-max-microvolt = <2850000>;
+						regulator-boot-on;
+					};
+
+					ldo7 {
+						regulator-name = "vdd-2v8-cam";
+						regulator-min-microvolt = <2800000>;
+						regulator-max-microvolt = <2800000>;
+					};
+
+					tps65913_ldo8: ldo8 {
+						regulator-name = "vdd-rtc";
+						regulator-min-microvolt = <950000>;
+						regulator-max-microvolt = <950000>;
+						regulator-always-on;
+						regulator-boot-on;
+						ti,enable-ldo8-tracking;
+					};
+
+					tps65913_ldo9: ldo9 {
+						regulator-name = "vdd-sdmmc";
+						regulator-min-microvolt = <1800000>;
+						regulator-max-microvolt = <2900000>;
+					};
+
+					tps65913_ldoln: ldoln {
+						regulator-name = "vdd-hdmi";
+						regulator-min-microvolt = <3300000>;
+						regulator-max-microvolt = <3300000>;
+					};
+
+					ldousb {
+						regulator-name = "vdd-usb";
+						regulator-min-microvolt = <3300000>;
+						regulator-max-microvolt = <3300000>;
+						regulator-always-on;
+						regulator-boot-on;
+					};
+				};
+			};
+
+			rtc {
+				compatible = "ti,palmas-rtc";
+				interrupt-parent = <&palmas>;
+				interrupts = <8 0>;
+			};
+
+			pinmux {
+				compatible = "ti,tps65913-pinctrl";
+				ti,palmas-enable-dvfs1;
+
+				pinctrl-names = "default";
+				pinctrl-0 = <&palmas_default>;
+
+				palmas_default: pinmux {
+					pin_powergood {
+						pins = "powergood";
+						function = "powergood";
+					};
+
+					pin_vac {
+						pins = "vac";
+						function = "vac";
+					};
+
+					pin_gpio0 {
+						pins = "gpio0";
+						function = "gpio";
+					};
+
+					pin_gpio1 {
+						pins = "gpio1";
+						function = "gpio";
+					};
+
+					pin_gpio2 {
+						pins = "gpio2";
+						function = "gpio";
+					};
+
+					pin_gpio3 {
+						pins = "gpio3";
+						function = "gpio";
+					};
+
+					pin_gpio4 {
+						pins = "gpio4";
+						function = "gpio";
+					};
+
+					pin_gpio5 {
+						pins = "gpio5";
+						function = "gpio";
+					};
+
+					pin_gpio6 {
+						pins = "gpio6";
+						function = "gpio";
+					};
+
+					pin_gpio7 {
+						pins = "gpio7";
+						function = "gpio";
+					};
+				};
+			};
+		};
+	};
+
+	ahub@70080000 {
+		i2s@70080300 {
+			status = "okay";
+		};
+	};
+
+	mmc@78000000 {
+		/* WiFi */
+	};
+
+	/* MicroSD card */
+	mmc@78000400 {
+		status = "okay";
+
+		bus-width = <4>;
+		cd-gpios = <&gpio TEGRA_GPIO(V, 2) GPIO_ACTIVE_LOW>;
+
+		nvidia,default-tap = <0x3>;
+		nvidia,default-trim = <0x3>;
+
+		vmmc-supply = <&vdd_usd>;
+		vqmmc-supply = <&tps65913_ldo9>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&sdmmc3_default>;
+	};
+
+	mmc@78000600 {
+		/* eMMC */
+	};
+
+	usb@7d000000 {
+		compatible = "nvidia,tegra114-udc";
+		status = "okay";
+		dr_mode = "peripheral";
+
+		/* Peripheral USB via ASUS connector */
+	};
+
+	usb-phy@7d000000 {
+		status = "okay";
+	};
+
+	usb@7d008000 {
+		status = "okay";
+
+		/* Host USB via dock */
+	};
+
+	usb-phy@7d008000 {
+		status = "okay";
+		vbus-supply = <&vdd_5v0_sys>;
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+
+		enable-gpios = <&gpio TEGRA_GPIO(H, 2) GPIO_ACTIVE_HIGH>;
+		power-supply = <&vdd_5v0_sys>;
+		pwms = <&pwm 1 1000000>;
+
+		brightness-levels = <1 255>;
+		num-interpolated-steps = <254>;
+		default-brightness-level = <224>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&backlight_default>;
+	};
+
+	/* PMIC has a built-in 32KHz oscillator which is used by PMC */
+	clk32k_in: clock-32k {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		clock-output-names = "pmic-oscillator";
+	};
+
+	firmware {
+		trusted-foundations {
+			compatible = "tlm,trusted-foundations";
+			tlm,version-major = <2>;
+			tlm,version-minor = <8>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		label = "GPIO Buttons";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_keys_default>;
+
+		button-power {
+			label = "Power";
+			gpios = <&gpio TEGRA_GPIO(Q, 0) GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_POWER>;
+			debounce-interval = <10>;
+			wakeup-source;
+		};
+
+		button-volume-up {
+			label = "Volume Up";
+			gpios = <&gpio TEGRA_GPIO(R, 2) GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+			debounce-interval = <10>;
+		};
+
+		button-volume-down {
+			label = "Volume Down";
+			gpios = <&gpio TEGRA_GPIO(R, 1) GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEDOWN>;
+			debounce-interval = <10>;
+		};
+	};
+
+	gpio-hall-sensor {
+		compatible = "gpio-keys";
+
+		label = "GPIO Hall Effect Sensor";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_hall_sensor_default>;
+
+		switch-hall-sensor {
+			label = "Hall Effect Sensor";
+			gpios = <&gpio TEGRA_GPIO(O, 5) GPIO_ACTIVE_LOW>;
+			linux,input-type = <EV_SW>;
+			linux,code = <SW_LID>;
+			linux,can-disable;
+			wakeup-source;
+		};
+	};
+
+	sound {
+		compatible = "asus,tegra-audio-rt5639-tf701t",
+			     "nvidia,tegra-audio-rt5640";
+		nvidia,model = "Asus Transformer Pad TF701T RT5639";
+
+		nvidia,audio-routing =
+			"Headphones", "HPOR",
+			"Headphones", "HPOL",
+			"Speakers", "SPORP",
+			"Speakers", "SPORN",
+			"Speakers", "SPOLP",
+			"Speakers", "SPOLN",
+			"Mic Jack", "MICBIAS1",
+			"IN2P", "Mic Jack";
+
+		nvidia,i2s-controller = <&tegra_i2s0>;
+		nvidia,audio-codec = <&rt5639>;
+
+		nvidia,hp-det-gpios = <&gpio TEGRA_GPIO(R, 7) GPIO_ACTIVE_LOW>;
+
+		clocks = <&tegra_car TEGRA114_CLK_PLL_A>,
+			 <&tegra_car TEGRA114_CLK_PLL_A_OUT0>,
+			 <&tegra_pmc TEGRA_PMC_CLK_OUT_1>;
+		clock-names = "pll_a", "pll_a_out0", "mclk";
+
+		assigned-clocks = <&tegra_car TEGRA114_CLK_EXTERN1>,
+				  <&tegra_pmc TEGRA_PMC_CLK_OUT_1>;
+
+		assigned-clock-parents = <&tegra_car TEGRA114_CLK_PLL_A_OUT0>,
+					 <&tegra_car TEGRA114_CLK_EXTERN1>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&hp_det_default>;
+	};
+
+	vdd_5v0_sys: regulator-5v0-sys {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_5v0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vdd_3v3_sys: regulator-3v3-sys {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vdd_lcd: regulator-vdd-lcd {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_lcd_1v8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&tps65913_smps8>;
+		enable-active-high;
+		gpio = <&gpio TEGRA_GPIO(CC, 4) GPIO_ACTIVE_HIGH>;
+		regulator-boot-on;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&vdd_lcd_default>;
+	};
+
+	vdd_usd: regulator-vdd-usd {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_sd_slot";
+		regulator-min-microvolt = <2900000>;
+		regulator-max-microvolt = <2900000>;
+		vin-supply = <&tps65913_smps9>;
+		enable-active-high;
+		gpio = <&gpio TEGRA_GPIO(K, 1) GPIO_ACTIVE_HIGH>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&sdmmc3_vdd_default>;
+	};
+};
diff --git a/arch/arm/boot/dts/tegra114-dalmore.dts b/arch/arm/boot/dts/tegra114-dalmore.dts
index 7fd901f8d39a..fffd62bcea6a 100644
--- a/arch/arm/boot/dts/tegra114-dalmore.dts
+++ b/arch/arm/boot/dts/tegra114-dalmore.dts
@@ -894,7 +894,7 @@
 		};
 
 		palmas: tps65913@58 {
-			compatible = "ti,palmas";
+			compatible = "ti,tps65913", "ti,palmas";
 			reg = <0x58>;
 			interrupts = <0 86 IRQ_TYPE_LEVEL_HIGH>;
 
@@ -1084,7 +1084,8 @@
 	spi@7000da00 {
 		status = "okay";
 		spi-max-frequency = <25000000>;
-		spi-flash@0 {
+
+		flash@0 {
 			compatible = "winbond,w25q32dw", "jedec,spi-nor";
 			reg = <0>;
 			spi-max-frequency = <20000000>;
@@ -1151,7 +1152,7 @@
 		default-brightness-level = <6>;
 	};
 
-	clk32k_in: clock@0 {
+	clk32k_in: clock-32k {
 		compatible = "fixed-clock";
 		clock-frequency = <32768>;
 		#clock-cells = <0>;
@@ -1160,33 +1161,33 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		home {
+		key-home {
 			label = "Home";
 			gpios = <&gpio TEGRA_GPIO(I, 5) GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_HOME>;
 		};
 
-		power {
+		key-power {
 			label = "Power";
 			gpios = <&gpio TEGRA_GPIO(Q, 0) GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
 			wakeup-source;
 		};
 
-		volume_down {
+		key-volume-down {
 			label = "Volume Down";
 			gpios = <&gpio TEGRA_GPIO(R, 1) GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_VOLUMEDOWN>;
 		};
 
-		volume_up {
+		key-volume-up {
 			label = "Volume Up";
 			gpios = <&gpio TEGRA_GPIO(R, 2) GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_VOLUMEUP>;
 		};
 	};
 
-	vdd_ac_bat_reg: regulator@0 {
+	vdd_ac_bat_reg: regulator-acbat {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd_ac_bat";
 		regulator-min-microvolt = <5000000>;
@@ -1194,7 +1195,7 @@
 		regulator-always-on;
 	};
 
-	dvdd_ts_reg: regulator@1 {
+	dvdd_ts_reg: regulator-ts {
 		compatible = "regulator-fixed";
 		regulator-name = "dvdd_ts";
 		regulator-min-microvolt = <1800000>;
@@ -1203,7 +1204,7 @@
 		gpio = <&gpio TEGRA_GPIO(H, 5) GPIO_ACTIVE_HIGH>;
 	};
 
-	usb1_vbus_reg: regulator@3 {
+	usb1_vbus_reg: regulator-usb1 {
 		compatible = "regulator-fixed";
 		regulator-name = "usb1_vbus";
 		regulator-min-microvolt = <5000000>;
@@ -1214,7 +1215,7 @@
 		vin-supply = <&tps65090_dcdc1_reg>;
 	};
 
-	usb3_vbus_reg: regulator@4 {
+	usb3_vbus_reg: regulator-usb3 {
 		compatible = "regulator-fixed";
 		regulator-name = "usb2_vbus";
 		regulator-min-microvolt = <5000000>;
@@ -1225,7 +1226,7 @@
 		vin-supply = <&tps65090_dcdc1_reg>;
 	};
 
-	vdd_hdmi_reg: regulator@5 {
+	vdd_hdmi_reg: regulator-hdmi {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd_hdmi_5v0";
 		regulator-min-microvolt = <5000000>;
@@ -1233,7 +1234,7 @@
 		vin-supply = <&tps65090_dcdc1_reg>;
 	};
 
-	vdd_cam_1v8_reg: regulator@6 {
+	vdd_cam_1v8_reg: regulator-cam {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd_cam_1v8_reg";
 		regulator-min-microvolt = <1800000>;
@@ -1242,7 +1243,7 @@
 		gpio = <&palmas_gpio 6 0>;
 	};
 
-	vdd_5v0_hdmi: regulator@7 {
+	vdd_5v0_hdmi: regulator-hdmicon {
 		compatible = "regulator-fixed";
 		regulator-name = "VDD_5V0_HDMI_CON";
 		regulator-min-microvolt = <5000000>;
diff --git a/arch/arm/boot/dts/tegra114-roth.dts b/arch/arm/boot/dts/tegra114-roth.dts
index 07960171fabe..b9d00009d1f4 100644
--- a/arch/arm/boot/dts/tegra114-roth.dts
+++ b/arch/arm/boot/dts/tegra114-roth.dts
@@ -801,7 +801,7 @@
 		};
 
 		palmas: pmic@58 {
-			compatible = "ti,palmas";
+			compatible = "ti,tps65913", "ti,palmas";
 			reg = <0x58>;
 			interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
 
@@ -1016,7 +1016,7 @@
 		enable-gpios = <&gpio TEGRA_GPIO(H, 2) GPIO_ACTIVE_HIGH>;
 	};
 
-	clk32k_in: clock@0 {
+	clk32k_in: clock-32k {
 		compatible = "fixed-clock";
 		clock-frequency = <32768>;
 		#clock-cells = <0>;
@@ -1025,19 +1025,19 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		back {
+		key-back {
 			label = "Back";
 			gpios = <&gpio TEGRA_GPIO(R, 2) GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_BACK>;
 		};
 
-		home {
+		key-home {
 			label = "Home";
 			gpios = <&gpio TEGRA_GPIO(R, 1) GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_HOME>;
 		};
 
-		power {
+		key-power {
 			label = "Power";
 			gpios = <&gpio TEGRA_GPIO(Q, 0) GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
@@ -1045,7 +1045,7 @@
 		};
 	};
 
-	lcd_bl_en: regulator@0 {
+	lcd_bl_en: regulator-lcden {
 		compatible = "regulator-fixed";
 		regulator-name = "lcd_bl_en";
 		regulator-min-microvolt = <5000000>;
@@ -1053,7 +1053,7 @@
 		regulator-boot-on;
 	};
 
-	vdd_lcd: regulator@1 {
+	vdd_lcd: regulator-lcd {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd_lcd_1v8";
 		regulator-min-microvolt = <1800000>;
@@ -1064,7 +1064,7 @@
 		regulator-boot-on;
 	};
 
-	regulator@2 {
+	regulator-1v8ts {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd_1v8_ts";
 		regulator-min-microvolt = <1800000>;
@@ -1073,7 +1073,7 @@
 		regulator-boot-on;
 	};
 
-	regulator@3 {
+	regulator-3v3ts {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd_3v3_ts";
 		regulator-min-microvolt = <3300000>;
@@ -1083,7 +1083,7 @@
 		regulator-boot-on;
 	};
 
-	regulator@4 {
+	regulator-1v8com {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd_1v8_com";
 		regulator-min-microvolt = <1800000>;
@@ -1094,7 +1094,7 @@
 		regulator-boot-on;
 	};
 
-	regulator@5 {
+	regulator-3v3com {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd_3v3_com";
 		regulator-min-microvolt = <3300000>;
diff --git a/arch/arm/boot/dts/tegra114-tn7.dts b/arch/arm/boot/dts/tegra114-tn7.dts
index 745d234b105b..f02d8c79eee7 100644
--- a/arch/arm/boot/dts/tegra114-tn7.dts
+++ b/arch/arm/boot/dts/tegra114-tn7.dts
@@ -62,7 +62,7 @@
 		clock-frequency = <400000>;
 
 		palmas: pmic@58 {
-			compatible = "ti,palmas";
+			compatible = "ti,tps65913", "ti,palmas";
 			reg = <0x58>;
 			interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
 
@@ -273,7 +273,7 @@
 		power-supply = <&lcd_bl_en>;
 	};
 
-	clk32k_in: clock@0 {
+	clk32k_in: clock-32k {
 		compatible = "fixed-clock";
 		clock-frequency = <32768>;
 		#clock-cells = <0>;
@@ -282,20 +282,20 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		power {
+		key-power {
 			label = "Power";
 			gpios = <&gpio TEGRA_GPIO(Q, 0) GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
 			wakeup-source;
 		};
 
-		volume_down {
+		key-volume-down {
 			label = "Volume Down";
 			gpios = <&gpio TEGRA_GPIO(Q, 2) GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_VOLUMEDOWN>;
 		};
 
-		volume_up {
+		key-volume-up {
 			label = "Volume Up";
 			gpios = <&gpio TEGRA_GPIO(R, 2) GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_VOLUMEUP>;
@@ -303,7 +303,7 @@
 	};
 
 	/* FIXME: output of BQ24192 */
-	vs_sys: regulator@0 {
+	vs_sys: regulator-vs {
 		compatible = "regulator-fixed";
 		regulator-name = "VS_SYS";
 		regulator-min-microvolt = <4200000>;
@@ -312,7 +312,7 @@
 		regulator-boot-on;
 	};
 
-	lcd_bl_en: regulator@1 {
+	lcd_bl_en: regulator-lcden {
 		compatible = "regulator-fixed";
 		regulator-name = "VDD_LCD_BL";
 		regulator-min-microvolt = <16500000>;
@@ -323,7 +323,7 @@
 		regulator-boot-on;
 	};
 
-	vdd_lcd: regulator@2 {
+	vdd_lcd: regulator-lcd {
 		compatible = "regulator-fixed";
 		regulator-name = "VD_LCD_1V8";
 		regulator-min-microvolt = <1800000>;
diff --git a/arch/arm/boot/dts/tegra114.dtsi b/arch/arm/boot/dts/tegra114.dtsi
index 546272e396b4..09996acad639 100644
--- a/arch/arm/boot/dts/tegra114.dtsi
+++ b/arch/arm/boot/dts/tegra114.dtsi
@@ -17,6 +17,19 @@
 		reg = <0x80000000 0x0>;
 	};
 
+	sram@40000000 {
+		compatible = "mmio-sram";
+		reg = <0x40000000 0x40000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0x40000000 0x40000>;
+
+		vde_pool: sram@400 {
+			reg = <0x400 0x3fc00>;
+			pool;
+		};
+	};
+
 	host1x@50000000 {
 		compatible = "nvidia,tegra114-host1x";
 		reg = <0x50000000 0x00028000>;
@@ -25,8 +38,8 @@
 		interrupt-names = "syncpt", "host1x";
 		clocks = <&tegra_car TEGRA114_CLK_HOST1X>;
 		clock-names = "host1x";
-		resets = <&tegra_car 28>;
-		reset-names = "host1x";
+		resets = <&tegra_car 28>, <&mc TEGRA114_MC_RESET_HC>;
+		reset-names = "host1x", "mc";
 		iommus = <&mc TEGRA_SWGROUP_HC>;
 
 		#address-cells = <1>;
@@ -39,8 +52,8 @@
 			reg = <0x54140000 0x00040000>;
 			interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&tegra_car TEGRA114_CLK_GR2D>;
-			resets = <&tegra_car 21>;
-			reset-names = "2d";
+			resets = <&tegra_car 21>, <&mc TEGRA114_MC_RESET_2D>;
+			reset-names = "2d", "mc";
 
 			iommus = <&mc TEGRA_SWGROUP_G2>;
 		};
@@ -49,8 +62,8 @@
 			compatible = "nvidia,tegra114-gr3d";
 			reg = <0x54180000 0x00040000>;
 			clocks = <&tegra_car TEGRA114_CLK_GR3D>;
-			resets = <&tegra_car 24>;
-			reset-names = "3d";
+			resets = <&tegra_car 24>, <&mc TEGRA114_MC_RESET_3D>;
+			reset-names = "3d", "mc";
 
 			iommus = <&mc TEGRA_SWGROUP_NV>;
 		};
@@ -105,7 +118,7 @@
 			status = "disabled";
 		};
 
-		dsi@54300000 {
+		dsia: dsi@54300000 {
 			compatible = "nvidia,tegra114-dsi";
 			reg = <0x54300000 0x00040000>;
 			clocks = <&tegra_car TEGRA114_CLK_DSIA>,
@@ -121,7 +134,7 @@
 			#size-cells = <0>;
 		};
 
-		dsi@54400000 {
+		dsib: dsi@54400000 {
 			compatible = "nvidia,tegra114-dsi";
 			reg = <0x54400000 0x00040000>;
 			clocks = <&tegra_car TEGRA114_CLK_DSIB>,
@@ -164,7 +177,7 @@
 	};
 
 	timer@60005000 {
-		compatible = "nvidia,tegra114-timer", "nvidia,tegra30-timer", "nvidia,tegra20-timer";
+		compatible = "nvidia,tegra114-timer", "nvidia,tegra30-timer";
 		reg = <0x60005000 0x400>;
 		interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
 			     <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>,
@@ -248,9 +261,31 @@
 		gpio-controller;
 		#interrupt-cells = <2>;
 		interrupt-controller;
-		/*
 		gpio-ranges = <&pinmux 0 0 246>;
-		*/
+	};
+
+	vde@6001a000 {
+		compatible = "nvidia,tegra114-vde";
+		reg = <0x6001a000 0x1000>, /* Syntax Engine */
+		      <0x6001b000 0x1000>, /* Video Bitstream Engine */
+		      <0x6001c000  0x100>, /* Macroblock Engine */
+		      <0x6001c200  0x100>, /* Post-processing Engine */
+		      <0x6001c400  0x100>, /* Motion Compensation Engine */
+		      <0x6001c600  0x100>, /* Transform Engine */
+		      <0x6001c800  0x100>, /* Pixel prediction block */
+		      <0x6001ca00  0x100>, /* Video DMA */
+		      <0x6001d800  0x400>; /* Video frame controls */
+		reg-names = "sxe", "bsev", "mbe", "ppe", "mce",
+			    "tfe", "ppb", "vdma", "frameid";
+		iram = <&vde_pool>; /* IRAM region */
+		interrupts = <GIC_SPI  9 IRQ_TYPE_LEVEL_HIGH>, /* Sync token interrupt */
+			     <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>, /* BSE-V interrupt */
+			     <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; /* SXE interrupt */
+		interrupt-names = "sync-token", "bsev", "sxe";
+		clocks = <&tegra_car TEGRA114_CLK_VDE>;
+		reset-names = "vde", "mc";
+		resets = <&tegra_car 61>, <&mc TEGRA114_MC_RESET_VDE>;
+		iommus = <&mc TEGRA_SWGROUP_VDE>;
 	};
 
 	apbmisc@70000800 {
@@ -542,6 +577,7 @@
 
 		interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
 
+		#reset-cells = <1>;
 		#iommu-cells = <1>;
 	};
 
diff --git a/arch/arm/boot/dts/tegra124-apalis-emc.dtsi b/arch/arm/boot/dts/tegra124-apalis-emc.dtsi
index a7ac805eeed5..7143c6b2ec3e 100644
--- a/arch/arm/boot/dts/tegra124-apalis-emc.dtsi
+++ b/arch/arm/boot/dts/tegra124-apalis-emc.dtsi
@@ -15,66 +15,77 @@
 				clocks = <&tegra_car TEGRA124_CLK_PLL_P>;
 				clock-names = "emc-parent";
 			};
+
 			timing-20400000 {
 				clock-frequency = <20400000>;
 				nvidia,parent-clock-frequency = <408000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_P>;
 				clock-names = "emc-parent";
 			};
+
 			timing-40800000 {
 				clock-frequency = <40800000>;
 				nvidia,parent-clock-frequency = <408000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_P>;
 				clock-names = "emc-parent";
 			};
+
 			timing-68000000 {
 				clock-frequency = <68000000>;
 				nvidia,parent-clock-frequency = <408000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_P>;
 				clock-names = "emc-parent";
 			};
+
 			timing-102000000 {
 				clock-frequency = <102000000>;
 				nvidia,parent-clock-frequency = <408000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_P>;
 				clock-names = "emc-parent";
 			};
+
 			timing-204000000 {
 				clock-frequency = <204000000>;
 				nvidia,parent-clock-frequency = <408000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_P>;
 				clock-names = "emc-parent";
 			};
+
 			timing-300000000 {
 				clock-frequency = <300000000>;
 				nvidia,parent-clock-frequency = <600000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_C>;
 				clock-names = "emc-parent";
 			};
+
 			timing-396000000 {
 				clock-frequency = <396000000>;
 				nvidia,parent-clock-frequency = <792000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_M>;
 				clock-names = "emc-parent";
 			};
+
 			timing-528000000 {
 				clock-frequency = <528000000>;
 				nvidia,parent-clock-frequency = <528000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_M_UD>;
 				clock-names = "emc-parent";
 			};
+
 			timing-600000000 {
 				clock-frequency = <600000000>;
 				nvidia,parent-clock-frequency = <600000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_C_UD>;
 				clock-names = "emc-parent";
 			};
+
 			timing-792000000 {
 				clock-frequency = <792000000>;
 				nvidia,parent-clock-frequency = <792000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_M_UD>;
 				clock-names = "emc-parent";
 			};
+
 			timing-924000000 {
 				clock-frequency = <924000000>;
 				nvidia,parent-clock-frequency = <924000000>;
@@ -84,6 +95,216 @@
 		};
 	};
 
+	memory-controller@70019000 {
+		emc-timings-1 {
+			nvidia,ram-code = <1>;
+
+			timing-12750000 {
+				clock-frequency = <12750000>;
+
+				nvidia,emem-configuration = <
+					0x40040001 0x8000000a
+					0x00000001 0x00000001
+					0x00000002 0x00000000
+					0x00000002 0x00000001
+					0x00000003 0x00000008
+					0x00000003 0x00000002
+					0x00000003 0x00000006
+					0x06030203 0x000a0502
+					0x77e30303 0x70000f03
+					0x001f0000
+				>;
+			};
+
+			timing-20400000 {
+				clock-frequency = <20400000>;
+
+				nvidia,emem-configuration = <
+					0x40020001 0x80000012
+					0x00000001 0x00000001
+					0x00000002 0x00000000
+					0x00000002 0x00000001
+					0x00000003 0x00000008
+					0x00000003 0x00000002
+					0x00000003 0x00000006
+					0x06030203 0x000a0502
+					0x76230303 0x70000f03
+					0x001f0000
+				>;
+			};
+
+			timing-40800000 {
+				clock-frequency = <40800000>;
+
+				nvidia,emem-configuration = <
+					0xa0000001 0x80000017
+					0x00000001 0x00000001
+					0x00000002 0x00000000
+					0x00000002 0x00000001
+					0x00000003 0x00000008
+					0x00000003 0x00000002
+					0x00000003 0x00000006
+					0x06030203 0x000a0502
+					0x74a30303 0x70000f03
+					0x001f0000
+				>;
+			};
+
+			timing-68000000 {
+				clock-frequency = <68000000>;
+
+				nvidia,emem-configuration = <
+					0x00000001 0x8000001e
+					0x00000001 0x00000001
+					0x00000002 0x00000000
+					0x00000002 0x00000001
+					0x00000003 0x00000008
+					0x00000003 0x00000002
+					0x00000003 0x00000006
+					0x06030203 0x000a0502
+					0x74230403 0x70000f03
+					0x001f0000
+				>;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emem-configuration = <
+					0x08000001 0x80000026
+					0x00000001 0x00000001
+					0x00000003 0x00000000
+					0x00000002 0x00000001
+					0x00000003 0x00000008
+					0x00000003 0x00000002
+					0x00000003 0x00000006
+					0x06030203 0x000a0503
+					0x73c30504 0x70000f03
+					0x001f0000
+				>;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emem-configuration = <
+					0x01000003 0x80000040
+					0x00000001 0x00000001
+					0x00000004 0x00000002
+					0x00000003 0x00000001
+					0x00000003 0x00000008
+					0x00000003 0x00000002
+					0x00000004 0x00000006
+					0x06040203 0x000a0504
+					0x73840a05 0x70000f03
+					0x001f0000
+				>;
+			};
+
+			timing-300000000 {
+				clock-frequency = <300000000>;
+
+				nvidia,emem-configuration = <
+					0x08000004 0x80000040
+					0x00000001 0x00000002
+					0x00000007 0x00000004
+					0x00000004 0x00000001
+					0x00000002 0x00000007
+					0x00000002 0x00000002
+					0x00000004 0x00000006
+					0x06040202 0x000b0607
+					0x77450e08 0x70000f03
+					0x001f0000
+				>;
+			};
+
+			timing-396000000 {
+				clock-frequency = <396000000>;
+
+				nvidia,emem-configuration = <
+					0x0f000005 0x80000040
+					0x00000001 0x00000002
+					0x00000009 0x00000005
+					0x00000006 0x00000001
+					0x00000002 0x00000008
+					0x00000002 0x00000002
+					0x00000004 0x00000006
+					0x06040202 0x000d0709
+					0x7586120a 0x70000f03
+					0x001f0000
+				>;
+			};
+
+			timing-528000000 {
+				clock-frequency = <528000000>;
+
+				nvidia,emem-configuration = <
+					0x0f000007 0x80000040
+					0x00000002 0x00000003
+					0x0000000c 0x00000007
+					0x00000008 0x00000001
+					0x00000002 0x00000009
+					0x00000002 0x00000002
+					0x00000005 0x00000006
+					0x06050202 0x0010090c
+					0x7428180d 0x70000f03
+					0x001f0000
+				>;
+			};
+
+			timing-600000000 {
+				clock-frequency = <600000000>;
+
+				nvidia,emem-configuration = <
+					0x00000009 0x80000040
+					0x00000003 0x00000004
+					0x0000000e 0x00000009
+					0x0000000a 0x00000001
+					0x00000003 0x0000000b
+					0x00000002 0x00000002
+					0x00000005 0x00000007
+					0x07050202 0x00130b0e
+					0x73a91b0f 0x70000f03
+					0x001f0000
+				>;
+			};
+
+			timing-792000000 {
+				clock-frequency = <792000000>;
+
+				nvidia,emem-configuration = <
+					0x0e00000b 0x80000040
+					0x00000004 0x00000005
+					0x00000013 0x0000000c
+					0x0000000d 0x00000002
+					0x00000003 0x0000000c
+					0x00000002 0x00000002
+					0x00000006 0x00000008
+					0x08060202 0x00170e13
+					0x736c2414 0x70000f02
+					0x001f0000
+				>;
+			};
+
+			timing-924000000 {
+				clock-frequency = <924000000>;
+
+				nvidia,emem-configuration = <
+					0x0e00000d 0x80000040
+					0x00000005 0x00000006
+					0x00000016 0x0000000e
+					0x0000000f 0x00000002
+					0x00000004 0x0000000e
+					0x00000002 0x00000002
+					0x00000006 0x00000009
+					0x09060202 0x001a1016
+					0x734e2a17 0x70000f02
+					0x001f0000
+				>;
+			};
+		};
+	};
+
 	external-memory-controller@7001b000 {
 		emc-timings-1 {
 			nvidia,ram-code = <1>;
@@ -1251,225 +1472,14 @@
 					0x00000011
 				>;
 			};
-
-		};
-	};
-
-	memory-controller@70019000 {
-		emc-timings-1 {
-			nvidia,ram-code = <1>;
-
-			timing-12750000 {
-				clock-frequency = <12750000>;
-
-				nvidia,emem-configuration = <
-					0x40040001 0x8000000a
-					0x00000001 0x00000001
-					0x00000002 0x00000000
-					0x00000002 0x00000001
-					0x00000003 0x00000008
-					0x00000003 0x00000002
-					0x00000003 0x00000006
-					0x06030203 0x000a0502
-					0x77e30303 0x70000f03
-					0x001f0000
-				>;
-			};
-
-			timing-20400000 {
-				clock-frequency = <20400000>;
-
-				nvidia,emem-configuration = <
-					0x40020001 0x80000012
-					0x00000001 0x00000001
-					0x00000002 0x00000000
-					0x00000002 0x00000001
-					0x00000003 0x00000008
-					0x00000003 0x00000002
-					0x00000003 0x00000006
-					0x06030203 0x000a0502
-					0x76230303 0x70000f03
-					0x001f0000
-				>;
-			};
-
-			timing-40800000 {
-				clock-frequency = <40800000>;
-
-				nvidia,emem-configuration = <
-					0xa0000001 0x80000017
-					0x00000001 0x00000001
-					0x00000002 0x00000000
-					0x00000002 0x00000001
-					0x00000003 0x00000008
-					0x00000003 0x00000002
-					0x00000003 0x00000006
-					0x06030203 0x000a0502
-					0x74a30303 0x70000f03
-					0x001f0000
-				>;
-			};
-
-			timing-68000000 {
-				clock-frequency = <68000000>;
-
-				nvidia,emem-configuration = <
-					0x00000001 0x8000001e
-					0x00000001 0x00000001
-					0x00000002 0x00000000
-					0x00000002 0x00000001
-					0x00000003 0x00000008
-					0x00000003 0x00000002
-					0x00000003 0x00000006
-					0x06030203 0x000a0502
-					0x74230403 0x70000f03
-					0x001f0000
-				>;
-			};
-
-			timing-102000000 {
-				clock-frequency = <102000000>;
-
-				nvidia,emem-configuration = <
-					0x08000001 0x80000026
-					0x00000001 0x00000001
-					0x00000003 0x00000000
-					0x00000002 0x00000001
-					0x00000003 0x00000008
-					0x00000003 0x00000002
-					0x00000003 0x00000006
-					0x06030203 0x000a0503
-					0x73c30504 0x70000f03
-					0x001f0000
-				>;
-			};
-
-			timing-204000000 {
-				clock-frequency = <204000000>;
-
-				nvidia,emem-configuration = <
-					0x01000003 0x80000040
-					0x00000001 0x00000001
-					0x00000004 0x00000002
-					0x00000003 0x00000001
-					0x00000003 0x00000008
-					0x00000003 0x00000002
-					0x00000004 0x00000006
-					0x06040203 0x000a0504
-					0x73840a05 0x70000f03
-					0x001f0000
-				>;
-			};
-
-			timing-300000000 {
-				clock-frequency = <300000000>;
-
-				nvidia,emem-configuration = <
-					0x08000004 0x80000040
-					0x00000001 0x00000002
-					0x00000007 0x00000004
-					0x00000004 0x00000001
-					0x00000002 0x00000007
-					0x00000002 0x00000002
-					0x00000004 0x00000006
-					0x06040202 0x000b0607
-					0x77450e08 0x70000f03
-					0x001f0000
-				>;
-			};
-
-			timing-396000000 {
-				clock-frequency = <396000000>;
-
-				nvidia,emem-configuration = <
-					0x0f000005 0x80000040
-					0x00000001 0x00000002
-					0x00000009 0x00000005
-					0x00000006 0x00000001
-					0x00000002 0x00000008
-					0x00000002 0x00000002
-					0x00000004 0x00000006
-					0x06040202 0x000d0709
-					0x7586120a 0x70000f03
-					0x001f0000
-				>;
-			};
-
-			timing-528000000 {
-				clock-frequency = <528000000>;
-
-				nvidia,emem-configuration = <
-					0x0f000007 0x80000040
-					0x00000002 0x00000003
-					0x0000000c 0x00000007
-					0x00000008 0x00000001
-					0x00000002 0x00000009
-					0x00000002 0x00000002
-					0x00000005 0x00000006
-					0x06050202 0x0010090c
-					0x7428180d 0x70000f03
-					0x001f0000
-				>;
-			};
-
-			timing-600000000 {
-				clock-frequency = <600000000>;
-
-				nvidia,emem-configuration = <
-					0x00000009 0x80000040
-					0x00000003 0x00000004
-					0x0000000e 0x00000009
-					0x0000000a 0x00000001
-					0x00000003 0x0000000b
-					0x00000002 0x00000002
-					0x00000005 0x00000007
-					0x07050202 0x00130b0e
-					0x73a91b0f 0x70000f03
-					0x001f0000
-				>;
-			};
-
-			timing-792000000 {
-				clock-frequency = <792000000>;
-
-				nvidia,emem-configuration = <
-					0x0e00000b 0x80000040
-					0x00000004 0x00000005
-					0x00000013 0x0000000c
-					0x0000000d 0x00000002
-					0x00000003 0x0000000c
-					0x00000002 0x00000002
-					0x00000006 0x00000008
-					0x08060202 0x00170e13
-					0x736c2414 0x70000f02
-					0x001f0000
-				>;
-			};
-
-			timing-924000000 {
-				clock-frequency = <924000000>;
-
-				nvidia,emem-configuration = <
-					0x0e00000d 0x80000040
-					0x00000005 0x00000006
-					0x00000016 0x0000000e
-					0x0000000f 0x00000002
-					0x00000004 0x0000000e
-					0x00000002 0x00000002
-					0x00000006 0x00000009
-					0x09060202 0x001a1016
-					0x734e2a17 0x70000f02
-					0x001f0000
-				>;
-			};
 		};
 	};
 };
 
 &emc_icc_dvfs_opp_table {
-	/delete-node/ opp@1200000000,1100;
+	/delete-node/ opp-1200000000-1100;
 };
 
 &emc_bw_dfs_opp_table {
-	/delete-node/ opp@1200000000;
+	/delete-node/ opp-1200000000;
 };
diff --git a/arch/arm/boot/dts/tegra124-apalis-eval.dts b/arch/arm/boot/dts/tegra124-apalis-eval.dts
index 28c29b6813a7..bce12b3411fc 100644
--- a/arch/arm/boot/dts/tegra124-apalis-eval.dts
+++ b/arch/arm/boot/dts/tegra124-apalis-eval.dts
@@ -191,7 +191,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		wakeup {
+		key-wakeup {
 			label = "WAKE1_MICO";
 			gpios = <&gpio TEGRA_GPIO(DD, 3) GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_WAKEUP>;
@@ -246,7 +246,7 @@
 
 &gpio {
 	/* Apalis GPIO7 MXM3 pin 15 PLX PEX 8605 PCIe Switch Reset */
-	pex-perst-n {
+	pex-perst-n-hog {
 		gpio-hog;
 		gpios = <TEGRA_GPIO(DD, 1) GPIO_ACTIVE_HIGH>;
 		output-high;
diff --git a/arch/arm/boot/dts/tegra124-apalis-v1.2-eval.dts b/arch/arm/boot/dts/tegra124-apalis-v1.2-eval.dts
index f3afde410615..800283ad6bdc 100644
--- a/arch/arm/boot/dts/tegra124-apalis-v1.2-eval.dts
+++ b/arch/arm/boot/dts/tegra124-apalis-v1.2-eval.dts
@@ -193,7 +193,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		wakeup {
+		key-wakeup {
 			label = "WAKE1_MICO";
 			gpios = <&gpio TEGRA_GPIO(DD, 3) GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_WAKEUP>;
@@ -248,7 +248,7 @@
 
 &gpio {
 	/* Apalis GPIO7 MXM3 pin 15 PLX PEX 8605 PCIe Switch Reset */
-	pex-perst-n {
+	pex-perst-n-hog {
 		gpio-hog;
 		gpios = <TEGRA_GPIO(DD, 1) GPIO_ACTIVE_HIGH>;
 		output-high;
diff --git a/arch/arm/boot/dts/tegra124-apalis-v1.2.dtsi b/arch/arm/boot/dts/tegra124-apalis-v1.2.dtsi
index cde9ae8fa04b..dbb0da08cb95 100644
--- a/arch/arm/boot/dts/tegra124-apalis-v1.2.dtsi
+++ b/arch/arm/boot/dts/tegra124-apalis-v1.2.dtsi
@@ -57,7 +57,7 @@
 		};
 	};
 
-	gpu@0,57000000 {
+	gpu@57000000 {
 		/*
 		 * Node left disabled on purpose - the bootloader will enable
 		 * it after having set the VPR up
@@ -1539,14 +1539,17 @@
 
 	serial@70006040 {
 		compatible = "nvidia,tegra124-hsuart", "nvidia,tegra30-hsuart";
+		/delete-property/ reg-shift;
 	};
 
 	serial@70006200 {
 		compatible = "nvidia,tegra124-hsuart", "nvidia,tegra30-hsuart";
+		/delete-property/ reg-shift;
 	};
 
 	serial@70006300 {
 		compatible = "nvidia,tegra124-hsuart", "nvidia,tegra30-hsuart";
+		/delete-property/ reg-shift;
 	};
 
 	hdmi_ddc: i2c@7000c700 {
@@ -1885,6 +1888,7 @@
 			usb2-0 {
 				status = "okay";
 				mode = "otg";
+				usb-role-switch;
 				vbus-supply = <&reg_usbo1_vbus>;
 			};
 
@@ -2021,7 +2025,7 @@
 	};
 
 	thermal-zones {
-		cpu {
+		cpu-thermal {
 			trips {
 				cpu-shutdown-trip {
 					temperature = <101000>;
@@ -2031,7 +2035,7 @@
 			};
 		};
 
-		mem {
+		mem-thermal {
 			trips {
 				mem-shutdown-trip {
 					temperature = <101000>;
@@ -2041,7 +2045,7 @@
 			};
 		};
 
-		gpu {
+		gpu-thermal {
 			trips {
 				gpu-shutdown-trip {
 					temperature = <101000>;
@@ -2055,7 +2059,7 @@
 
 &gpio {
 	/* I210 Gigabit Ethernet Controller Reset */
-	lan-reset-n {
+	lan-reset-n-hog {
 		gpio-hog;
 		gpios = <TEGRA_GPIO(S, 2) GPIO_ACTIVE_HIGH>;
 		output-high;
@@ -2063,7 +2067,7 @@
 	};
 
 	/* Control MXM3 pin 26 Reset Module Output Carrier Input */
-	reset-moci-ctrl {
+	reset-moci-ctrl-hog {
 		gpio-hog;
 		gpios = <TEGRA_GPIO(U, 4) GPIO_ACTIVE_HIGH>;
 		output-high;
diff --git a/arch/arm/boot/dts/tegra124-apalis.dtsi b/arch/arm/boot/dts/tegra124-apalis.dtsi
index a46d9ba9bb7a..d3f16c117b0c 100644
--- a/arch/arm/boot/dts/tegra124-apalis.dtsi
+++ b/arch/arm/boot/dts/tegra124-apalis.dtsi
@@ -56,7 +56,7 @@
 		};
 	};
 
-	gpu@0,57000000 {
+	gpu@57000000 {
 		/*
 		 * Node left disabled on purpose - the bootloader will enable
 		 * it after having set the VPR up
@@ -1532,14 +1532,17 @@
 
 	serial@70006040 {
 		compatible = "nvidia,tegra124-hsuart", "nvidia,tegra30-hsuart";
+		/delete-property/ reg-shift;
 	};
 
 	serial@70006200 {
 		compatible = "nvidia,tegra124-hsuart", "nvidia,tegra30-hsuart";
+		/delete-property/ reg-shift;
 	};
 
 	serial@70006300 {
 		compatible = "nvidia,tegra124-hsuart", "nvidia,tegra30-hsuart";
+		/delete-property/ reg-shift;
 	};
 
 	hdmi_ddc: i2c@7000c400 {
@@ -1877,6 +1880,7 @@
 			usb2-0 {
 				status = "okay";
 				mode = "otg";
+				usb-role-switch;
 				vbus-supply = <&reg_usbo1_vbus>;
 			};
 
@@ -2013,7 +2017,7 @@
 	};
 
 	thermal-zones {
-		cpu {
+		cpu-thermal {
 			trips {
 				cpu-shutdown-trip {
 					temperature = <101000>;
@@ -2023,7 +2027,7 @@
 			};
 		};
 
-		mem {
+		mem-thermal {
 			trips {
 				mem-shutdown-trip {
 					temperature = <101000>;
@@ -2033,7 +2037,7 @@
 			};
 		};
 
-		gpu {
+		gpu-thermal {
 			trips {
 				gpu-shutdown-trip {
 					temperature = <101000>;
@@ -2047,7 +2051,7 @@
 
 &gpio {
 	/* I210 Gigabit Ethernet Controller Reset */
-	lan-reset-n {
+	lan-reset-n-hog {
 		gpio-hog;
 		gpios = <TEGRA_GPIO(S, 2) GPIO_ACTIVE_HIGH>;
 		output-high;
@@ -2055,7 +2059,7 @@
 	};
 
 	/* Control MXM3 pin 26 Reset Module Output Carrier Input */
-	reset-moci-ctrl {
+	reset-moci-ctrl-hog {
 		gpio-hog;
 		gpios = <TEGRA_GPIO(U, 4) GPIO_ACTIVE_HIGH>;
 		output-high;
diff --git a/arch/arm/boot/dts/tegra124-jetson-tk1-emc.dtsi b/arch/arm/boot/dts/tegra124-jetson-tk1-emc.dtsi
index df4e463afbd1..79e776db5f37 100644
--- a/arch/arm/boot/dts/tegra124-jetson-tk1-emc.dtsi
+++ b/arch/arm/boot/dts/tegra124-jetson-tk1-emc.dtsi
@@ -10,66 +10,77 @@
 				clocks = <&tegra_car TEGRA124_CLK_PLL_P>;
 				clock-names = "emc-parent";
 			};
+
 			timing-20400000 {
 				clock-frequency = <20400000>;
 				nvidia,parent-clock-frequency = <408000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_P>;
 				clock-names = "emc-parent";
 			};
+
 			timing-40800000 {
 				clock-frequency = <40800000>;
 				nvidia,parent-clock-frequency = <408000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_P>;
 				clock-names = "emc-parent";
 			};
+
 			timing-68000000 {
 				clock-frequency = <68000000>;
 				nvidia,parent-clock-frequency = <408000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_P>;
 				clock-names = "emc-parent";
 			};
+
 			timing-102000000 {
 				clock-frequency = <102000000>;
 				nvidia,parent-clock-frequency = <408000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_P>;
 				clock-names = "emc-parent";
 			};
+
 			timing-204000000 {
 				clock-frequency = <204000000>;
 				nvidia,parent-clock-frequency = <408000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_P>;
 				clock-names = "emc-parent";
 			};
+
 			timing-300000000 {
 				clock-frequency = <300000000>;
 				nvidia,parent-clock-frequency = <600000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_C>;
 				clock-names = "emc-parent";
 			};
+
 			timing-396000000 {
 				clock-frequency = <396000000>;
 				nvidia,parent-clock-frequency = <792000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_M>;
 				clock-names = "emc-parent";
 			};
+
 			timing-528000000 {
 				clock-frequency = <528000000>;
 				nvidia,parent-clock-frequency = <528000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_M_UD>;
 				clock-names = "emc-parent";
 			};
+
 			timing-600000000 {
 				clock-frequency = <600000000>;
 				nvidia,parent-clock-frequency = <600000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_C_UD>;
 				clock-names = "emc-parent";
 			};
+
 			timing-792000000 {
 				clock-frequency = <792000000>;
 				nvidia,parent-clock-frequency = <792000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_M_UD>;
 				clock-names = "emc-parent";
 			};
+
 			timing-924000000 {
 				clock-frequency = <924000000>;
 				nvidia,parent-clock-frequency = <924000000>;
@@ -79,6 +90,324 @@
 		};
 	};
 
+	memory-controller@70019000 {
+		emc-timings-3 {
+			nvidia,ram-code = <3>;
+
+			timing-12750000 {
+				clock-frequency = <12750000>;
+
+				nvidia,emem-configuration = <
+					0x40040001
+					0x8000000a
+					0x00000001
+					0x00000001
+					0x00000002
+					0x00000000
+					0x00000002
+					0x00000001
+					0x00000003
+					0x00000008
+					0x00000003
+					0x00000002
+					0x00000003
+					0x00000006
+					0x06030203
+					0x000a0502
+					0x77e30303
+					0x70000f03
+					0x001f0000
+				>;
+			};
+
+			timing-20400000 {
+				clock-frequency = <20400000>;
+
+				nvidia,emem-configuration = <
+					0x40020001
+					0x80000012
+					0x00000001
+					0x00000001
+					0x00000002
+					0x00000000
+					0x00000002
+					0x00000001
+					0x00000003
+					0x00000008
+					0x00000003
+					0x00000002
+					0x00000003
+					0x00000006
+					0x06030203
+					0x000a0502
+					0x76230303
+					0x70000f03
+					0x001f0000
+				>;
+			};
+
+			timing-40800000 {
+				clock-frequency = <40800000>;
+
+				nvidia,emem-configuration = <
+					0xa0000001
+					0x80000017
+					0x00000001
+					0x00000001
+					0x00000002
+					0x00000000
+					0x00000002
+					0x00000001
+					0x00000003
+					0x00000008
+					0x00000003
+					0x00000002
+					0x00000003
+					0x00000006
+					0x06030203
+					0x000a0502
+					0x74a30303
+					0x70000f03
+					0x001f0000
+				>;
+			};
+
+			timing-68000000 {
+				clock-frequency = <68000000>;
+
+				nvidia,emem-configuration = <
+					0x00000001
+					0x8000001e
+					0x00000001
+					0x00000001
+					0x00000002
+					0x00000000
+					0x00000002
+					0x00000001
+					0x00000003
+					0x00000008
+					0x00000003
+					0x00000002
+					0x00000003
+					0x00000006
+					0x06030203
+					0x000a0502
+					0x74230403
+					0x70000f03
+					0x001f0000
+				>;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emem-configuration = <
+					0x08000001
+					0x80000026
+					0x00000001
+					0x00000001
+					0x00000003
+					0x00000000
+					0x00000002
+					0x00000001
+					0x00000003
+					0x00000008
+					0x00000003
+					0x00000002
+					0x00000003
+					0x00000006
+					0x06030203
+					0x000a0503
+					0x73c30504
+					0x70000f03
+					0x001f0000
+				>;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emem-configuration = <
+					0x01000003
+					0x80000040
+					0x00000001
+					0x00000001
+					0x00000004
+					0x00000002
+					0x00000003
+					0x00000001
+					0x00000003
+					0x00000008
+					0x00000003
+					0x00000002
+					0x00000004
+					0x00000006
+					0x06040203
+					0x000a0504
+					0x73840a05
+					0x70000f03
+					0x001f0000
+				>;
+			};
+
+			timing-300000000 {
+				clock-frequency = <300000000>;
+
+				nvidia,emem-configuration = <
+					0x08000004
+					0x80000040
+					0x00000001
+					0x00000002
+					0x00000007
+					0x00000004
+					0x00000004
+					0x00000001
+					0x00000002
+					0x00000007
+					0x00000002
+					0x00000002
+					0x00000004
+					0x00000006
+					0x06040202
+					0x000b0607
+					0x77450e08
+					0x70000f03
+					0x001f0000
+				>;
+			};
+
+			timing-396000000 {
+				clock-frequency = <396000000>;
+
+				nvidia,emem-configuration = <
+					0x0f000005
+					0x80000040
+					0x00000001
+					0x00000002
+					0x00000009
+					0x00000005
+					0x00000006
+					0x00000001
+					0x00000002
+					0x00000008
+					0x00000002
+					0x00000002
+					0x00000004
+					0x00000006
+					0x06040202
+					0x000d0709
+					0x7586120a
+					0x70000f03
+					0x001f0000
+				>;
+			};
+
+			timing-528000000 {
+				clock-frequency = <528000000>;
+
+				nvidia,emem-configuration = <
+					0x0f000007
+					0x80000040
+					0x00000002
+					0x00000003
+					0x0000000c
+					0x00000007
+					0x00000008
+					0x00000001
+					0x00000002
+					0x00000009
+					0x00000002
+					0x00000002
+					0x00000005
+					0x00000006
+					0x06050202
+					0x0010090c
+					0x7428180d
+					0x70000f03
+					0x001f0000
+				>;
+			};
+
+			timing-600000000 {
+				clock-frequency = <600000000>;
+
+				nvidia,emem-configuration = <
+					0x00000009
+					0x80000040
+					0x00000003
+					0x00000004
+					0x0000000e
+					0x00000009
+					0x0000000a
+					0x00000001
+					0x00000003
+					0x0000000b
+					0x00000002
+					0x00000002
+					0x00000005
+					0x00000007
+					0x07050202
+					0x00130b0e
+					0x73a91b0f
+					0x70000f03
+					0x001f0000
+				>;
+			};
+
+			timing-792000000 {
+				clock-frequency = <792000000>;
+
+				nvidia,emem-configuration = <
+					0x0e00000b
+					0x80000040
+					0x00000004
+					0x00000005
+					0x00000013
+					0x0000000c
+					0x0000000d
+					0x00000002
+					0x00000003
+					0x0000000c
+					0x00000002
+					0x00000002
+					0x00000006
+					0x00000008
+					0x08060202
+					0x00170e13
+					0x736c2414
+					0x70000f02
+					0x001f0000
+				>;
+			};
+
+			timing-924000000 {
+				clock-frequency = <924000000>;
+
+				nvidia,emem-configuration = <
+					0x0e00000d
+					0x80000040
+					0x00000005
+					0x00000006
+					0x00000016
+					0x0000000e
+					0x0000000f
+					0x00000002
+					0x00000004
+					0x0000000e
+					0x00000002
+					0x00000002
+					0x00000006
+					0x00000009
+					0x09060202
+					0x001a1016
+					0x734e2a17
+					0x70000f02
+					0x001f0000
+				>;
+			};
+		};
+	};
+
 	external-memory-controller@7001b000 {
 		emc-timings-3 {
 			nvidia,ram-code = <3>;
@@ -2098,333 +2427,14 @@
 					0x00000011
 				>;
 			};
-
-		};
-	};
-
-	memory-controller@70019000 {
-		emc-timings-3 {
-			nvidia,ram-code = <3>;
-
-			timing-12750000 {
-				clock-frequency = <12750000>;
-
-				nvidia,emem-configuration = <
-					0x40040001
-					0x8000000a
-					0x00000001
-					0x00000001
-					0x00000002
-					0x00000000
-					0x00000002
-					0x00000001
-					0x00000003
-					0x00000008
-					0x00000003
-					0x00000002
-					0x00000003
-					0x00000006
-					0x06030203
-					0x000a0502
-					0x77e30303
-					0x70000f03
-					0x001f0000
-				>;
-			};
-
-			timing-20400000 {
-				clock-frequency = <20400000>;
-
-				nvidia,emem-configuration = <
-					0x40020001
-					0x80000012
-					0x00000001
-					0x00000001
-					0x00000002
-					0x00000000
-					0x00000002
-					0x00000001
-					0x00000003
-					0x00000008
-					0x00000003
-					0x00000002
-					0x00000003
-					0x00000006
-					0x06030203
-					0x000a0502
-					0x76230303
-					0x70000f03
-					0x001f0000
-				>;
-			};
-
-			timing-40800000 {
-				clock-frequency = <40800000>;
-
-				nvidia,emem-configuration = <
-					0xa0000001
-					0x80000017
-					0x00000001
-					0x00000001
-					0x00000002
-					0x00000000
-					0x00000002
-					0x00000001
-					0x00000003
-					0x00000008
-					0x00000003
-					0x00000002
-					0x00000003
-					0x00000006
-					0x06030203
-					0x000a0502
-					0x74a30303
-					0x70000f03
-					0x001f0000
-				>;
-			};
-
-			timing-68000000 {
-				clock-frequency = <68000000>;
-
-				nvidia,emem-configuration = <
-					0x00000001
-					0x8000001e
-					0x00000001
-					0x00000001
-					0x00000002
-					0x00000000
-					0x00000002
-					0x00000001
-					0x00000003
-					0x00000008
-					0x00000003
-					0x00000002
-					0x00000003
-					0x00000006
-					0x06030203
-					0x000a0502
-					0x74230403
-					0x70000f03
-					0x001f0000
-				>;
-			};
-
-			timing-102000000 {
-				clock-frequency = <102000000>;
-
-				nvidia,emem-configuration = <
-					0x08000001
-					0x80000026
-					0x00000001
-					0x00000001
-					0x00000003
-					0x00000000
-					0x00000002
-					0x00000001
-					0x00000003
-					0x00000008
-					0x00000003
-					0x00000002
-					0x00000003
-					0x00000006
-					0x06030203
-					0x000a0503
-					0x73c30504
-					0x70000f03
-					0x001f0000
-				>;
-			};
-
-			timing-204000000 {
-				clock-frequency = <204000000>;
-
-				nvidia,emem-configuration = <
-					0x01000003
-					0x80000040
-					0x00000001
-					0x00000001
-					0x00000004
-					0x00000002
-					0x00000003
-					0x00000001
-					0x00000003
-					0x00000008
-					0x00000003
-					0x00000002
-					0x00000004
-					0x00000006
-					0x06040203
-					0x000a0504
-					0x73840a05
-					0x70000f03
-					0x001f0000
-				>;
-			};
-
-			timing-300000000 {
-				clock-frequency = <300000000>;
-
-				nvidia,emem-configuration = <
-					0x08000004
-					0x80000040
-					0x00000001
-					0x00000002
-					0x00000007
-					0x00000004
-					0x00000004
-					0x00000001
-					0x00000002
-					0x00000007
-					0x00000002
-					0x00000002
-					0x00000004
-					0x00000006
-					0x06040202
-					0x000b0607
-					0x77450e08
-					0x70000f03
-					0x001f0000
-				>;
-			};
-
-			timing-396000000 {
-				clock-frequency = <396000000>;
-
-				nvidia,emem-configuration = <
-					0x0f000005
-					0x80000040
-					0x00000001
-					0x00000002
-					0x00000009
-					0x00000005
-					0x00000006
-					0x00000001
-					0x00000002
-					0x00000008
-					0x00000002
-					0x00000002
-					0x00000004
-					0x00000006
-					0x06040202
-					0x000d0709
-					0x7586120a
-					0x70000f03
-					0x001f0000
-				>;
-			};
-
-			timing-528000000 {
-				clock-frequency = <528000000>;
-
-				nvidia,emem-configuration = <
-					0x0f000007
-					0x80000040
-					0x00000002
-					0x00000003
-					0x0000000c
-					0x00000007
-					0x00000008
-					0x00000001
-					0x00000002
-					0x00000009
-					0x00000002
-					0x00000002
-					0x00000005
-					0x00000006
-					0x06050202
-					0x0010090c
-					0x7428180d
-					0x70000f03
-					0x001f0000
-				>;
-			};
-
-			timing-600000000 {
-				clock-frequency = <600000000>;
-
-				nvidia,emem-configuration = <
-					0x00000009
-					0x80000040
-					0x00000003
-					0x00000004
-					0x0000000e
-					0x00000009
-					0x0000000a
-					0x00000001
-					0x00000003
-					0x0000000b
-					0x00000002
-					0x00000002
-					0x00000005
-					0x00000007
-					0x07050202
-					0x00130b0e
-					0x73a91b0f
-					0x70000f03
-					0x001f0000
-				>;
-			};
-
-			timing-792000000 {
-				clock-frequency = <792000000>;
-
-				nvidia,emem-configuration = <
-					0x0e00000b
-					0x80000040
-					0x00000004
-					0x00000005
-					0x00000013
-					0x0000000c
-					0x0000000d
-					0x00000002
-					0x00000003
-					0x0000000c
-					0x00000002
-					0x00000002
-					0x00000006
-					0x00000008
-					0x08060202
-					0x00170e13
-					0x736c2414
-					0x70000f02
-					0x001f0000
-				>;
-			};
-
-			timing-924000000 {
-				clock-frequency = <924000000>;
-
-				nvidia,emem-configuration = <
-					0x0e00000d
-					0x80000040
-					0x00000005
-					0x00000006
-					0x00000016
-					0x0000000e
-					0x0000000f
-					0x00000002
-					0x00000004
-					0x0000000e
-					0x00000002
-					0x00000002
-					0x00000006
-					0x00000009
-					0x09060202
-					0x001a1016
-					0x734e2a17
-					0x70000f02
-					0x001f0000
-				>;
-			};
 		};
 	};
 };
 
 &emc_icc_dvfs_opp_table {
-	/delete-node/ opp@1200000000,1100;
+	/delete-node/ opp-1200000000-1100;
 };
 
 &emc_bw_dfs_opp_table {
-	/delete-node/ opp@1200000000;
+	/delete-node/ opp-1200000000;
 };
diff --git a/arch/arm/boot/dts/tegra124-jetson-tk1.dts b/arch/arm/boot/dts/tegra124-jetson-tk1.dts
index 35ab296408e1..f41dd4039c07 100644
--- a/arch/arm/boot/dts/tegra124-jetson-tk1.dts
+++ b/arch/arm/boot/dts/tegra124-jetson-tk1.dts
@@ -72,7 +72,7 @@
 		status = "okay";
 	};
 
-	gpu@0,57000000 {
+	gpu@57000000 {
 		/*
 		 * Node left disabled on purpose - the bootloader will enable
 		 * it after having set the VPR up
@@ -1389,6 +1389,7 @@
 	 */
 	serial@70006000 {
 		compatible = "nvidia,tegra124-hsuart", "nvidia,tegra30-hsuart";
+		/delete-property/ reg-shift;
 		status = "okay";
 	};
 
@@ -1401,6 +1402,7 @@
 	 */
 	serial@70006040 {
 		compatible = "nvidia,tegra124-hsuart", "nvidia,tegra30-hsuart";
+		/delete-property/ reg-shift;
 		status = "okay";
 	};
 
@@ -1655,7 +1657,8 @@
 	spi@7000da00 {
 		status = "okay";
 		spi-max-frequency = <25000000>;
-		spi-flash@0 {
+
+		flash@0 {
 			compatible = "winbond,w25q32dw", "jedec,spi-nor";
 			reg = <0>;
 			spi-max-frequency = <20000000>;
@@ -1868,7 +1871,7 @@
 		vbus-supply = <&vdd_usb3_vbus>;
 	};
 
-	clk32k_in: clock@0 {
+	clk32k_in: clock-32k {
 		compatible = "fixed-clock";
 		clock-frequency = <32768>;
 		#clock-cells = <0>;
@@ -1883,7 +1886,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		power {
+		key-power {
 			label = "Power";
 			gpios = <&gpio TEGRA_GPIO(Q, 0) GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
@@ -1892,7 +1895,7 @@
 		};
 	};
 
-	vdd_mux: regulator@0 {
+	vdd_mux: regulator-mux {
 		compatible = "regulator-fixed";
 		regulator-name = "+VDD_MUX";
 		regulator-min-microvolt = <12000000>;
@@ -1901,7 +1904,7 @@
 		regulator-boot-on;
 	};
 
-	vdd_5v0_sys: regulator@1 {
+	vdd_5v0_sys: regulator-5v0sys {
 		compatible = "regulator-fixed";
 		regulator-name = "+5V_SYS";
 		regulator-min-microvolt = <5000000>;
@@ -1911,7 +1914,7 @@
 		vin-supply = <&vdd_mux>;
 	};
 
-	vdd_3v3_sys: regulator@2 {
+	vdd_3v3_sys: regulator-3v3sys {
 		compatible = "regulator-fixed";
 		regulator-name = "+3.3V_SYS";
 		regulator-min-microvolt = <3300000>;
@@ -1921,7 +1924,7 @@
 		vin-supply = <&vdd_mux>;
 	};
 
-	vdd_3v3_run: regulator@3 {
+	vdd_3v3_run: regulator-3v3run {
 		compatible = "regulator-fixed";
 		regulator-name = "+3.3V_RUN";
 		regulator-min-microvolt = <3300000>;
@@ -1933,7 +1936,7 @@
 		vin-supply = <&vdd_3v3_sys>;
 	};
 
-	vdd_3v3_hdmi: regulator@4 {
+	vdd_3v3_hdmi: regulator-3v3hdmi {
 		compatible = "regulator-fixed";
 		regulator-name = "+3.3V_AVDD_HDMI_AP_GATED";
 		regulator-min-microvolt = <3300000>;
@@ -1941,7 +1944,7 @@
 		vin-supply = <&vdd_3v3_run>;
 	};
 
-	vdd_usb1_vbus: regulator@5 {
+	vdd_usb1_vbus: regulator-usb1 {
 		compatible = "regulator-fixed";
 		regulator-name = "+USB0_VBUS_SW";
 		regulator-min-microvolt = <5000000>;
@@ -1952,7 +1955,7 @@
 		vin-supply = <&vdd_5v0_sys>;
 	};
 
-	vdd_usb3_vbus: regulator@6 {
+	vdd_usb3_vbus: regulator-usb3 {
 		compatible = "regulator-fixed";
 		regulator-name = "+5V_USB_HS";
 		regulator-min-microvolt = <5000000>;
@@ -1963,7 +1966,7 @@
 		vin-supply = <&vdd_5v0_sys>;
 	};
 
-	vdd_3v3_lp0: regulator@7 {
+	vdd_3v3_lp0: regulator-lp0 {
 		compatible = "regulator-fixed";
 		regulator-name = "+3.3V_LP0";
 		regulator-min-microvolt = <3300000>;
@@ -1975,7 +1978,7 @@
 		vin-supply = <&vdd_3v3_sys>;
 	};
 
-	vdd_hdmi_pll: regulator@8 {
+	vdd_hdmi_pll: regulator-hdmipll {
 		compatible = "regulator-fixed";
 		regulator-name = "+1.05V_RUN_AVDD_HDMI_PLL";
 		regulator-min-microvolt = <1050000>;
@@ -1984,7 +1987,7 @@
 		vin-supply = <&vdd_1v05_run>;
 	};
 
-	vdd_5v0_hdmi: regulator@9 {
+	vdd_5v0_hdmi: regulator-hdmicon {
 		compatible = "regulator-fixed";
 		regulator-name = "+5V_HDMI_CON";
 		regulator-min-microvolt = <5000000>;
@@ -1995,7 +1998,7 @@
 	};
 
 	/* Molex power connector */
-	vdd_5v0_sata: regulator@10 {
+	vdd_5v0_sata: regulator-5v0sata {
 		compatible = "regulator-fixed";
 		regulator-name = "+5V_SATA";
 		regulator-min-microvolt = <5000000>;
@@ -2005,7 +2008,7 @@
 		vin-supply = <&vdd_5v0_sys>;
 	};
 
-	vdd_12v0_sata: regulator@11 {
+	vdd_12v0_sata: regulator-12v0sata {
 		compatible = "regulator-fixed";
 		regulator-name = "+12V_SATA";
 		regulator-min-microvolt = <12000000>;
@@ -2044,7 +2047,7 @@
 	};
 
 	thermal-zones {
-		cpu {
+		cpu-thermal {
 			trips {
 				cpu-shutdown-trip {
 					temperature = <101000>;
@@ -2054,7 +2057,7 @@
 			};
 		};
 
-		mem {
+		mem-thermal {
 			trips {
 				mem-shutdown-trip {
 					temperature = <101000>;
@@ -2064,7 +2067,7 @@
 			};
 		};
 
-		gpu {
+		gpu-thermal {
 			trips {
 				gpu-shutdown-trip {
 					temperature = <101000>;
diff --git a/arch/arm/boot/dts/tegra124-nyan-big-emc.dtsi b/arch/arm/boot/dts/tegra124-nyan-big-emc.dtsi
index a0f56cc9da5c..31b2e26c69d4 100644
--- a/arch/arm/boot/dts/tegra124-nyan-big-emc.dtsi
+++ b/arch/arm/boot/dts/tegra124-nyan-big-emc.dtsi
@@ -14,60 +14,70 @@
 				clocks = <&tegra_car TEGRA124_CLK_PLL_P>;
 				clock-names = "emc-parent";
 			};
+
 			timing-20400000 {
 				clock-frequency = <20400000>;
 				nvidia,parent-clock-frequency = <408000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_P>;
 				clock-names = "emc-parent";
 			};
+
 			timing-40800000 {
 				clock-frequency = <40800000>;
 				nvidia,parent-clock-frequency = <408000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_P>;
 				clock-names = "emc-parent";
 			};
+
 			timing-68000000 {
 				clock-frequency = <68000000>;
 				nvidia,parent-clock-frequency = <408000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_P>;
 				clock-names = "emc-parent";
 			};
+
 			timing-102000000 {
 				clock-frequency = <102000000>;
 				nvidia,parent-clock-frequency = <408000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_P>;
 				clock-names = "emc-parent";
 			};
+
 			timing-204000000 {
 				clock-frequency = <204000000>;
 				nvidia,parent-clock-frequency = <408000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_P>;
 				clock-names = "emc-parent";
 			};
+
 			timing-300000000 {
 				clock-frequency = <300000000>;
 				nvidia,parent-clock-frequency = <600000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_C>;
 				clock-names = "emc-parent";
 			};
+
 			timing-396000000 {
 				clock-frequency = <396000000>;
 				nvidia,parent-clock-frequency = <792000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_M>;
 				clock-names = "emc-parent";
 			};
+
 			timing-528000000 {
 				clock-frequency = <528000000>;
 				nvidia,parent-clock-frequency = <528000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_M_UD>;
 				clock-names = "emc-parent";
 			};
+
 			timing-600000000 {
 				clock-frequency = <600000000>;
 				nvidia,parent-clock-frequency = <600000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_C_UD>;
 				clock-names = "emc-parent";
 			};
+
 			timing-792000000 {
 				clock-frequency = <792000000>;
 				nvidia,parent-clock-frequency = <792000000>;
@@ -85,60 +95,70 @@
 				clocks = <&tegra_car TEGRA124_CLK_PLL_P>;
 				clock-names = "emc-parent";
 			};
+
 			timing-20400000 {
 				clock-frequency = <20400000>;
 				nvidia,parent-clock-frequency = <408000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_P>;
 				clock-names = "emc-parent";
 			};
+
 			timing-40800000 {
 				clock-frequency = <40800000>;
 				nvidia,parent-clock-frequency = <408000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_P>;
 				clock-names = "emc-parent";
 			};
+
 			timing-68000000 {
 				clock-frequency = <68000000>;
 				nvidia,parent-clock-frequency = <408000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_P>;
 				clock-names = "emc-parent";
 			};
+
 			timing-102000000 {
 				clock-frequency = <102000000>;
 				nvidia,parent-clock-frequency = <408000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_P>;
 				clock-names = "emc-parent";
 			};
+
 			timing-204000000 {
 				clock-frequency = <204000000>;
 				nvidia,parent-clock-frequency = <408000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_P>;
 				clock-names = "emc-parent";
 			};
+
 			timing-300000000 {
 				clock-frequency = <300000000>;
 				nvidia,parent-clock-frequency = <600000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_C>;
 				clock-names = "emc-parent";
 			};
+
 			timing-396000000 {
 				clock-frequency = <396000000>;
 				nvidia,parent-clock-frequency = <792000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_M>;
 				clock-names = "emc-parent";
 			};
+
 			timing-528000000 {
 				clock-frequency = <528000000>;
 				nvidia,parent-clock-frequency = <528000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_M_UD>;
 				clock-names = "emc-parent";
 			};
+
 			timing-600000000 {
 				clock-frequency = <600000000>;
 				nvidia,parent-clock-frequency = <600000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_C_UD>;
 				clock-names = "emc-parent";
 			};
+
 			timing-792000000 {
 				clock-frequency = <792000000>;
 				nvidia,parent-clock-frequency = <792000000>;
@@ -156,60 +176,70 @@
 				clocks = <&tegra_car TEGRA124_CLK_PLL_P>;
 				clock-names = "emc-parent";
 			};
+
 			timing-20400000 {
 				clock-frequency = <20400000>;
 				nvidia,parent-clock-frequency = <408000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_P>;
 				clock-names = "emc-parent";
 			};
+
 			timing-40800000 {
 				clock-frequency = <40800000>;
 				nvidia,parent-clock-frequency = <408000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_P>;
 				clock-names = "emc-parent";
 			};
+
 			timing-68000000 {
 				clock-frequency = <68000000>;
 				nvidia,parent-clock-frequency = <408000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_P>;
 				clock-names = "emc-parent";
 			};
+
 			timing-102000000 {
 				clock-frequency = <102000000>;
 				nvidia,parent-clock-frequency = <408000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_P>;
 				clock-names = "emc-parent";
 			};
+
 			timing-204000000 {
 				clock-frequency = <204000000>;
 				nvidia,parent-clock-frequency = <408000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_P>;
 				clock-names = "emc-parent";
 			};
+
 			timing-300000000 {
 				clock-frequency = <300000000>;
 				nvidia,parent-clock-frequency = <600000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_C>;
 				clock-names = "emc-parent";
 			};
+
 			timing-396000000 {
 				clock-frequency = <396000000>;
 				nvidia,parent-clock-frequency = <792000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_M>;
 				clock-names = "emc-parent";
 			};
+
 			timing-528000000 {
 				clock-frequency = <528000000>;
 				nvidia,parent-clock-frequency = <528000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_M_UD>;
 				clock-names = "emc-parent";
 			};
+
 			timing-600000000 {
 				clock-frequency = <600000000>;
 				nvidia,parent-clock-frequency = <600000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_C_UD>;
 				clock-names = "emc-parent";
 			};
+
 			timing-792000000 {
 				clock-frequency = <792000000>;
 				nvidia,parent-clock-frequency = <792000000>;
@@ -219,6 +249,878 @@
 		};
 	};
 
+	memory-controller@70019000 {
+		emc-timings-1 {
+			nvidia,ram-code = <1>;
+
+			timing-12750000 {
+				clock-frequency = <12750000>;
+
+				nvidia,emem-configuration = <
+					0x40040001 /* MC_EMEM_ARB_CFG */
+					0x8000000a /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000002 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000003 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000003 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06030203 /* MC_EMEM_ARB_DA_TURNS */
+					0x000a0402 /* MC_EMEM_ARB_DA_COVERS */
+					0x77e30303 /* MC_EMEM_ARB_MISC0 */
+					0x70000f03 /* MC_EMEM_ARB_MISC1 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-20400000 {
+				clock-frequency = <20400000>;
+
+				nvidia,emem-configuration = <
+					0x40020001 /* MC_EMEM_ARB_CFG */
+					0x80000012 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000002 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000003 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000003 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06030203 /* MC_EMEM_ARB_DA_TURNS */
+					0x000a0402 /* MC_EMEM_ARB_DA_COVERS */
+					0x76230303 /* MC_EMEM_ARB_MISC0 */
+					0x70000f03 /* MC_EMEM_ARB_MISC1 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-40800000 {
+				clock-frequency = <40800000>;
+
+				nvidia,emem-configuration = <
+					0xa0000001 /* MC_EMEM_ARB_CFG */
+					0x80000017 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000002 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000003 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000003 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06030203 /* MC_EMEM_ARB_DA_TURNS */
+					0x000a0402 /* MC_EMEM_ARB_DA_COVERS */
+					0x74a30303 /* MC_EMEM_ARB_MISC0 */
+					0x70000f03 /* MC_EMEM_ARB_MISC1 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-68000000 {
+				clock-frequency = <68000000>;
+
+				nvidia,emem-configuration = <
+					0x00000001 /* MC_EMEM_ARB_CFG */
+					0x8000001e /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000002 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000003 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000003 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06030203 /* MC_EMEM_ARB_DA_TURNS */
+					0x000a0402 /* MC_EMEM_ARB_DA_COVERS */
+					0x74230403 /* MC_EMEM_ARB_MISC0 */
+					0x70000f03 /* MC_EMEM_ARB_MISC1 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emem-configuration = <
+					0x08000001 /* MC_EMEM_ARB_CFG */
+					0x80000026 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000002 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000003 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000003 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06030203 /* MC_EMEM_ARB_DA_TURNS */
+					0x000a0403 /* MC_EMEM_ARB_DA_COVERS */
+					0x73c30504 /* MC_EMEM_ARB_MISC0 */
+					0x70000f03 /* MC_EMEM_ARB_MISC1 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emem-configuration = <
+					0x01000003 /* MC_EMEM_ARB_CFG */
+					0x80000040 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000005 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000004 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000003 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000004 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06040203 /* MC_EMEM_ARB_DA_TURNS */
+					0x000a0405 /* MC_EMEM_ARB_DA_COVERS */
+					0x73840a06 /* MC_EMEM_ARB_MISC0 */
+					0x70000f03 /* MC_EMEM_ARB_MISC1 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-300000000 {
+				clock-frequency = <300000000>;
+
+				nvidia,emem-configuration = <
+					0x08000004 /* MC_EMEM_ARB_CFG */
+					0x80000040 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000007 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000004 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000005 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000007 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000004 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06040202 /* MC_EMEM_ARB_DA_TURNS */
+					0x000b0607 /* MC_EMEM_ARB_DA_COVERS */
+					0x77450e08 /* MC_EMEM_ARB_MISC0 */
+					0x70000f03 /* MC_EMEM_ARB_MISC1 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-396000000 {
+				clock-frequency = <396000000>;
+
+				nvidia,emem-configuration = <
+					0x0f000005 /* MC_EMEM_ARB_CFG */
+					0x80000040 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000009 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000005 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000007 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000004 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06040202 /* MC_EMEM_ARB_DA_TURNS */
+					0x000d0709 /* MC_EMEM_ARB_DA_COVERS */
+					0x7586120a /* MC_EMEM_ARB_MISC0 */
+					0x70000f03 /* MC_EMEM_ARB_MISC1 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-528000000 {
+				clock-frequency = <528000000>;
+
+				nvidia,emem-configuration = <
+					0x0f000007 /* MC_EMEM_ARB_CFG */
+					0x80000040 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RP */
+					0x0000000d /* MC_EMEM_ARB_TIMING_RC */
+					0x00000008 /* MC_EMEM_ARB_TIMING_RAS */
+					0x0000000a /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000009 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000005 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06050202 /* MC_EMEM_ARB_DA_TURNS */
+					0x0010090d /* MC_EMEM_ARB_DA_COVERS */
+					0x7428180e /* MC_EMEM_ARB_MISC0 */
+					0x70000f03 /* MC_EMEM_ARB_MISC1 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-600000000 {
+				clock-frequency = <600000000>;
+
+				nvidia,emem-configuration = <
+					0x00000009 /* MC_EMEM_ARB_CFG */
+					0x80000040 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000004 /* MC_EMEM_ARB_TIMING_RP */
+					0x0000000e /* MC_EMEM_ARB_TIMING_RC */
+					0x00000009 /* MC_EMEM_ARB_TIMING_RAS */
+					0x0000000b /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x0000000b /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000005 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000007 /* MC_EMEM_ARB_TIMING_W2R */
+					0x07050202 /* MC_EMEM_ARB_DA_TURNS */
+					0x00130b0e /* MC_EMEM_ARB_DA_COVERS */
+					0x73a91b0f /* MC_EMEM_ARB_MISC0 */
+					0x70000f03 /* MC_EMEM_ARB_MISC1 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-792000000 {
+				clock-frequency = <792000000>;
+
+				nvidia,emem-configuration = <
+					0x0e00000b /* MC_EMEM_ARB_CFG */
+					0x80000040 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000004 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000005 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000013 /* MC_EMEM_ARB_TIMING_RC */
+					0x0000000c /* MC_EMEM_ARB_TIMING_RAS */
+					0x0000000f /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x0000000c /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000008 /* MC_EMEM_ARB_TIMING_W2R */
+					0x08060202 /* MC_EMEM_ARB_DA_TURNS */
+					0x00160d13 /* MC_EMEM_ARB_DA_COVERS */
+					0x734c2414 /* MC_EMEM_ARB_MISC0 */
+					0x70000f02 /* MC_EMEM_ARB_MISC1 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+		};
+
+		emc-timings-4 {
+			nvidia,ram-code = <4>;
+
+			timing-12750000 {
+				clock-frequency = <12750000>;
+
+				nvidia,emem-configuration = <
+					0x40040001 /* MC_EMEM_ARB_CFG */
+					0x8000000a /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000002 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000003 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000003 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06030203 /* MC_EMEM_ARB_DA_TURNS */
+					0x000a0502 /* MC_EMEM_ARB_DA_COVERS */
+					0x77e30303 /* MC_EMEM_ARB_MISC0 */
+					0x70000f03 /* MC_EMEM_ARB_MISC1 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-20400000 {
+				clock-frequency = <20400000>;
+
+				nvidia,emem-configuration = <
+					0x40020001 /* MC_EMEM_ARB_CFG */
+					0x80000012 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000002 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000003 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000003 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06030203 /* MC_EMEM_ARB_DA_TURNS */
+					0x000a0502 /* MC_EMEM_ARB_DA_COVERS */
+					0x77430303 /* MC_EMEM_ARB_MISC0 */
+					0x70000f03 /* MC_EMEM_ARB_MISC1 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-40800000 {
+				clock-frequency = <40800000>;
+
+				nvidia,emem-configuration = <
+					0xa0000001 /* MC_EMEM_ARB_CFG */
+					0x80000017 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000002 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000003 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000003 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06030203 /* MC_EMEM_ARB_DA_TURNS */
+					0x000a0502 /* MC_EMEM_ARB_DA_COVERS */
+					0x75e30303 /* MC_EMEM_ARB_MISC0 */
+					0x70000f03 /* MC_EMEM_ARB_MISC1 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-68000000 {
+				clock-frequency = <68000000>;
+
+				nvidia,emem-configuration = <
+					0x00000001 /* MC_EMEM_ARB_CFG */
+					0x8000001e /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000002 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000003 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000003 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06030203 /* MC_EMEM_ARB_DA_TURNS */
+					0x000a0502 /* MC_EMEM_ARB_DA_COVERS */
+					0x75430403 /* MC_EMEM_ARB_MISC0 */
+					0x70000f03 /* MC_EMEM_ARB_MISC1 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emem-configuration = <
+					0x08000001 /* MC_EMEM_ARB_CFG */
+					0x80000026 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000002 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000003 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000003 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06030203 /* MC_EMEM_ARB_DA_TURNS */
+					0x000a0503 /* MC_EMEM_ARB_DA_COVERS */
+					0x74e30504 /* MC_EMEM_ARB_MISC0 */
+					0x70000f03 /* MC_EMEM_ARB_MISC1 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emem-configuration = <
+					0x01000003 /* MC_EMEM_ARB_CFG */
+					0x80000040 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000004 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000004 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000003 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000004 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06040203 /* MC_EMEM_ARB_DA_TURNS */
+					0x000a0504 /* MC_EMEM_ARB_DA_COVERS */
+					0x74a40a05 /* MC_EMEM_ARB_MISC0 */
+					0x70000f03 /* MC_EMEM_ARB_MISC1 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-300000000 {
+				clock-frequency = <300000000>;
+
+				nvidia,emem-configuration = <
+					0x08000004 /* MC_EMEM_ARB_CFG */
+					0x80000040 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000007 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000004 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000005 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000007 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000004 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06040202 /* MC_EMEM_ARB_DA_TURNS */
+					0x000b0607 /* MC_EMEM_ARB_DA_COVERS */
+					0x77450e08 /* MC_EMEM_ARB_MISC0 */
+					0x70000f03 /* MC_EMEM_ARB_MISC1 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-396000000 {
+				clock-frequency = <396000000>;
+
+				nvidia,emem-configuration = <
+					0x0f000005 /* MC_EMEM_ARB_CFG */
+					0x80000040 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000009 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000005 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000007 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000004 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06040202 /* MC_EMEM_ARB_DA_TURNS */
+					0x000d0709 /* MC_EMEM_ARB_DA_COVERS */
+					0x7586120a /* MC_EMEM_ARB_MISC0 */
+					0x70000f03 /* MC_EMEM_ARB_MISC1 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-528000000 {
+				clock-frequency = <528000000>;
+
+				nvidia,emem-configuration = <
+					0x0f000007 /* MC_EMEM_ARB_CFG */
+					0x80000040 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RP */
+					0x0000000c /* MC_EMEM_ARB_TIMING_RC */
+					0x00000007 /* MC_EMEM_ARB_TIMING_RAS */
+					0x0000000a /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000009 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000005 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06050202 /* MC_EMEM_ARB_DA_TURNS */
+					0x0010090c /* MC_EMEM_ARB_DA_COVERS */
+					0x7488180d /* MC_EMEM_ARB_MISC0 */
+					0x70000f03 /* MC_EMEM_ARB_MISC1 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-600000000 {
+				clock-frequency = <600000000>;
+
+				nvidia,emem-configuration = <
+					0x00000009 /* MC_EMEM_ARB_CFG */
+					0x80000040 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000004 /* MC_EMEM_ARB_TIMING_RP */
+					0x0000000e /* MC_EMEM_ARB_TIMING_RC */
+					0x00000009 /* MC_EMEM_ARB_TIMING_RAS */
+					0x0000000b /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x0000000b /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000005 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000007 /* MC_EMEM_ARB_TIMING_W2R */
+					0x07050202 /* MC_EMEM_ARB_DA_TURNS */
+					0x00130b0e /* MC_EMEM_ARB_DA_COVERS */
+					0x74691b0f /* MC_EMEM_ARB_MISC0 */
+					0x70000f03 /* MC_EMEM_ARB_MISC1 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-792000000 {
+				clock-frequency = <792000000>;
+
+				nvidia,emem-configuration = <
+					0x0e00000b /* MC_EMEM_ARB_CFG */
+					0x80000040 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000004 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000005 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000013 /* MC_EMEM_ARB_TIMING_RC */
+					0x0000000c /* MC_EMEM_ARB_TIMING_RAS */
+					0x0000000f /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x0000000c /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000008 /* MC_EMEM_ARB_TIMING_W2R */
+					0x08060202 /* MC_EMEM_ARB_DA_TURNS */
+					0x00170e13 /* MC_EMEM_ARB_DA_COVERS */
+					0x746c2414 /* MC_EMEM_ARB_MISC0 */
+					0x70000f02 /* MC_EMEM_ARB_MISC1 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+		};
+
+		emc-timings-6 {
+			nvidia,ram-code = <6>;
+
+			timing-12750000 {
+				clock-frequency = <12750000>;
+
+				nvidia,emem-configuration = <
+					0x40040001 /* MC_EMEM_ARB_CFG */
+					0x8000000a /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000002 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000003 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000003 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06030203 /* MC_EMEM_ARB_DA_TURNS */
+					0x000a0402 /* MC_EMEM_ARB_DA_COVERS */
+					0x77e30303 /* MC_EMEM_ARB_MISC0 */
+					0x70000f03 /* MC_EMEM_ARB_MISC1 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-20400000 {
+				clock-frequency = <20400000>;
+
+				nvidia,emem-configuration = <
+					0x40020001 /* MC_EMEM_ARB_CFG */
+					0x80000012 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000002 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000003 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000003 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06030203 /* MC_EMEM_ARB_DA_TURNS */
+					0x000a0402 /* MC_EMEM_ARB_DA_COVERS */
+					0x76230303 /* MC_EMEM_ARB_MISC0 */
+					0x70000f03 /* MC_EMEM_ARB_MISC1 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-40800000 {
+				clock-frequency = <40800000>;
+
+				nvidia,emem-configuration = <
+					0xa0000001 /* MC_EMEM_ARB_CFG */
+					0x80000017 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000002 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000003 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000003 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06030203 /* MC_EMEM_ARB_DA_TURNS */
+					0x000a0402 /* MC_EMEM_ARB_DA_COVERS */
+					0x74a30303 /* MC_EMEM_ARB_MISC0 */
+					0x70000f03 /* MC_EMEM_ARB_MISC1 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-68000000 {
+				clock-frequency = <68000000>;
+
+				nvidia,emem-configuration = <
+					0x00000001 /* MC_EMEM_ARB_CFG */
+					0x8000001e /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000002 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000003 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000003 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06030203 /* MC_EMEM_ARB_DA_TURNS */
+					0x000a0402 /* MC_EMEM_ARB_DA_COVERS */
+					0x74230403 /* MC_EMEM_ARB_MISC0 */
+					0x70000f03 /* MC_EMEM_ARB_MISC1 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emem-configuration = <
+					0x08000001 /* MC_EMEM_ARB_CFG */
+					0x80000026 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000002 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000003 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000003 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06030203 /* MC_EMEM_ARB_DA_TURNS */
+					0x000a0403 /* MC_EMEM_ARB_DA_COVERS */
+					0x73c30504 /* MC_EMEM_ARB_MISC0 */
+					0x70000f03 /* MC_EMEM_ARB_MISC1 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emem-configuration = <
+					0x01000003 /* MC_EMEM_ARB_CFG */
+					0x80000040 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000005 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000004 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000003 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000004 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06040203 /* MC_EMEM_ARB_DA_TURNS */
+					0x000a0405 /* MC_EMEM_ARB_DA_COVERS */
+					0x73840a06 /* MC_EMEM_ARB_MISC0 */
+					0x70000f03 /* MC_EMEM_ARB_MISC1 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-300000000 {
+				clock-frequency = <300000000>;
+
+				nvidia,emem-configuration = <
+					0x08000004 /* MC_EMEM_ARB_CFG */
+					0x80000040 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000007 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000004 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000005 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000007 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000004 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06040202 /* MC_EMEM_ARB_DA_TURNS */
+					0x000b0607 /* MC_EMEM_ARB_DA_COVERS */
+					0x77450e08 /* MC_EMEM_ARB_MISC0 */
+					0x70000f03 /* MC_EMEM_ARB_MISC1 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-396000000 {
+				clock-frequency = <396000000>;
+
+				nvidia,emem-configuration = <
+					0x0f000005 /* MC_EMEM_ARB_CFG */
+					0x80000040 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000009 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000005 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000007 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000004 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06040202 /* MC_EMEM_ARB_DA_TURNS */
+					0x000d0709 /* MC_EMEM_ARB_DA_COVERS */
+					0x7586120a /* MC_EMEM_ARB_MISC0 */
+					0x70000f03 /* MC_EMEM_ARB_MISC1 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-528000000 {
+				clock-frequency = <528000000>;
+
+				nvidia,emem-configuration = <
+					0x0f000007 /* MC_EMEM_ARB_CFG */
+					0x80000040 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RP */
+					0x0000000d /* MC_EMEM_ARB_TIMING_RC */
+					0x00000008 /* MC_EMEM_ARB_TIMING_RAS */
+					0x0000000a /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000009 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000005 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06050202 /* MC_EMEM_ARB_DA_TURNS */
+					0x0010090d /* MC_EMEM_ARB_DA_COVERS */
+					0x7428180e /* MC_EMEM_ARB_MISC0 */
+					0x70000f03 /* MC_EMEM_ARB_MISC1 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-600000000 {
+				clock-frequency = <600000000>;
+
+				nvidia,emem-configuration = <
+					0x00000009 /* MC_EMEM_ARB_CFG */
+					0x80000040 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000004 /* MC_EMEM_ARB_TIMING_RP */
+					0x0000000e /* MC_EMEM_ARB_TIMING_RC */
+					0x00000009 /* MC_EMEM_ARB_TIMING_RAS */
+					0x0000000b /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x0000000b /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000005 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000007 /* MC_EMEM_ARB_TIMING_W2R */
+					0x07050202 /* MC_EMEM_ARB_DA_TURNS */
+					0x00130b0e /* MC_EMEM_ARB_DA_COVERS */
+					0x73a91b0f /* MC_EMEM_ARB_MISC0 */
+					0x70000f03 /* MC_EMEM_ARB_MISC1 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-792000000 {
+				clock-frequency = <792000000>;
+
+				nvidia,emem-configuration = <
+					0x0e00000b /* MC_EMEM_ARB_CFG */
+					0x80000040 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000004 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000005 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000013 /* MC_EMEM_ARB_TIMING_RC */
+					0x0000000c /* MC_EMEM_ARB_TIMING_RAS */
+					0x0000000f /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x0000000c /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000008 /* MC_EMEM_ARB_TIMING_W2R */
+					0x08060202 /* MC_EMEM_ARB_DA_TURNS */
+					0x00160d13 /* MC_EMEM_ARB_DA_COVERS */
+					0x734c2414 /* MC_EMEM_ARB_MISC0 */
+					0x70000f02 /* MC_EMEM_ARB_MISC1 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+		};
+	};
+
 	external-memory-controller@7001b000 {
 		emc-timings-1 {
 			nvidia,ram-code = <1>;
@@ -5776,886 +6678,14 @@
 			};
 		};
 	};
-
-	memory-controller@70019000 {
-		emc-timings-1 {
-			nvidia,ram-code = <1>;
-
-			timing-12750000 {
-				clock-frequency = <12750000>;
-
-				nvidia,emem-configuration = <
-					0x40040001 /* MC_EMEM_ARB_CFG */
-					0x8000000a /* MC_EMEM_ARB_OUTSTANDING_REQ */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RC */
-					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
-					0x00000002 /* MC_EMEM_ARB_TIMING_FAW */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
-					0x00000003 /* MC_EMEM_ARB_TIMING_R2R */
-					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
-					0x00000003 /* MC_EMEM_ARB_TIMING_R2W */
-					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
-					0x06030203 /* MC_EMEM_ARB_DA_TURNS */
-					0x000a0402 /* MC_EMEM_ARB_DA_COVERS */
-					0x77e30303 /* MC_EMEM_ARB_MISC0 */
-					0x70000f03 /* MC_EMEM_ARB_MISC1 */
-					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-				>;
-			};
-
-			timing-20400000 {
-				clock-frequency = <20400000>;
-
-				nvidia,emem-configuration = <
-					0x40020001 /* MC_EMEM_ARB_CFG */
-					0x80000012 /* MC_EMEM_ARB_OUTSTANDING_REQ */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RC */
-					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
-					0x00000002 /* MC_EMEM_ARB_TIMING_FAW */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
-					0x00000003 /* MC_EMEM_ARB_TIMING_R2R */
-					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
-					0x00000003 /* MC_EMEM_ARB_TIMING_R2W */
-					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
-					0x06030203 /* MC_EMEM_ARB_DA_TURNS */
-					0x000a0402 /* MC_EMEM_ARB_DA_COVERS */
-					0x76230303 /* MC_EMEM_ARB_MISC0 */
-					0x70000f03 /* MC_EMEM_ARB_MISC1 */
-					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-				>;
-			};
-
-			timing-40800000 {
-				clock-frequency = <40800000>;
-
-				nvidia,emem-configuration = <
-					0xa0000001 /* MC_EMEM_ARB_CFG */
-					0x80000017 /* MC_EMEM_ARB_OUTSTANDING_REQ */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RC */
-					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
-					0x00000002 /* MC_EMEM_ARB_TIMING_FAW */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
-					0x00000003 /* MC_EMEM_ARB_TIMING_R2R */
-					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
-					0x00000003 /* MC_EMEM_ARB_TIMING_R2W */
-					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
-					0x06030203 /* MC_EMEM_ARB_DA_TURNS */
-					0x000a0402 /* MC_EMEM_ARB_DA_COVERS */
-					0x74a30303 /* MC_EMEM_ARB_MISC0 */
-					0x70000f03 /* MC_EMEM_ARB_MISC1 */
-					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-				>;
-			};
-
-			timing-68000000 {
-				clock-frequency = <68000000>;
-
-				nvidia,emem-configuration = <
-					0x00000001 /* MC_EMEM_ARB_CFG */
-					0x8000001e /* MC_EMEM_ARB_OUTSTANDING_REQ */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RC */
-					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
-					0x00000002 /* MC_EMEM_ARB_TIMING_FAW */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
-					0x00000003 /* MC_EMEM_ARB_TIMING_R2R */
-					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
-					0x00000003 /* MC_EMEM_ARB_TIMING_R2W */
-					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
-					0x06030203 /* MC_EMEM_ARB_DA_TURNS */
-					0x000a0402 /* MC_EMEM_ARB_DA_COVERS */
-					0x74230403 /* MC_EMEM_ARB_MISC0 */
-					0x70000f03 /* MC_EMEM_ARB_MISC1 */
-					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-				>;
-			};
-
-			timing-102000000 {
-				clock-frequency = <102000000>;
-
-				nvidia,emem-configuration = <
-					0x08000001 /* MC_EMEM_ARB_CFG */
-					0x80000026 /* MC_EMEM_ARB_OUTSTANDING_REQ */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
-					0x00000003 /* MC_EMEM_ARB_TIMING_RC */
-					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
-					0x00000002 /* MC_EMEM_ARB_TIMING_FAW */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
-					0x00000003 /* MC_EMEM_ARB_TIMING_R2R */
-					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
-					0x00000003 /* MC_EMEM_ARB_TIMING_R2W */
-					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
-					0x06030203 /* MC_EMEM_ARB_DA_TURNS */
-					0x000a0403 /* MC_EMEM_ARB_DA_COVERS */
-					0x73c30504 /* MC_EMEM_ARB_MISC0 */
-					0x70000f03 /* MC_EMEM_ARB_MISC1 */
-					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-				>;
-			};
-
-			timing-204000000 {
-				clock-frequency = <204000000>;
-
-				nvidia,emem-configuration = <
-					0x01000003 /* MC_EMEM_ARB_CFG */
-					0x80000040 /* MC_EMEM_ARB_OUTSTANDING_REQ */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
-					0x00000005 /* MC_EMEM_ARB_TIMING_RC */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RAS */
-					0x00000004 /* MC_EMEM_ARB_TIMING_FAW */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
-					0x00000003 /* MC_EMEM_ARB_TIMING_R2R */
-					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
-					0x00000004 /* MC_EMEM_ARB_TIMING_R2W */
-					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
-					0x06040203 /* MC_EMEM_ARB_DA_TURNS */
-					0x000a0405 /* MC_EMEM_ARB_DA_COVERS */
-					0x73840a06 /* MC_EMEM_ARB_MISC0 */
-					0x70000f03 /* MC_EMEM_ARB_MISC1 */
-					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-				>;
-			};
-
-			timing-300000000 {
-				clock-frequency = <300000000>;
-
-				nvidia,emem-configuration = <
-					0x08000004 /* MC_EMEM_ARB_CFG */
-					0x80000040 /* MC_EMEM_ARB_OUTSTANDING_REQ */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RP */
-					0x00000007 /* MC_EMEM_ARB_TIMING_RC */
-					0x00000004 /* MC_EMEM_ARB_TIMING_RAS */
-					0x00000005 /* MC_EMEM_ARB_TIMING_FAW */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-					0x00000007 /* MC_EMEM_ARB_TIMING_WAP2PRE */
-					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
-					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
-					0x00000004 /* MC_EMEM_ARB_TIMING_R2W */
-					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
-					0x06040202 /* MC_EMEM_ARB_DA_TURNS */
-					0x000b0607 /* MC_EMEM_ARB_DA_COVERS */
-					0x77450e08 /* MC_EMEM_ARB_MISC0 */
-					0x70000f03 /* MC_EMEM_ARB_MISC1 */
-					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-				>;
-			};
-
-			timing-396000000 {
-				clock-frequency = <396000000>;
-
-				nvidia,emem-configuration = <
-					0x0f000005 /* MC_EMEM_ARB_CFG */
-					0x80000040 /* MC_EMEM_ARB_OUTSTANDING_REQ */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RP */
-					0x00000009 /* MC_EMEM_ARB_TIMING_RC */
-					0x00000005 /* MC_EMEM_ARB_TIMING_RAS */
-					0x00000007 /* MC_EMEM_ARB_TIMING_FAW */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
-					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
-					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
-					0x00000004 /* MC_EMEM_ARB_TIMING_R2W */
-					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
-					0x06040202 /* MC_EMEM_ARB_DA_TURNS */
-					0x000d0709 /* MC_EMEM_ARB_DA_COVERS */
-					0x7586120a /* MC_EMEM_ARB_MISC0 */
-					0x70000f03 /* MC_EMEM_ARB_MISC1 */
-					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-				>;
-			};
-
-			timing-528000000 {
-				clock-frequency = <528000000>;
-
-				nvidia,emem-configuration = <
-					0x0f000007 /* MC_EMEM_ARB_CFG */
-					0x80000040 /* MC_EMEM_ARB_OUTSTANDING_REQ */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RCD */
-					0x00000003 /* MC_EMEM_ARB_TIMING_RP */
-					0x0000000d /* MC_EMEM_ARB_TIMING_RC */
-					0x00000008 /* MC_EMEM_ARB_TIMING_RAS */
-					0x0000000a /* MC_EMEM_ARB_TIMING_FAW */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-					0x00000009 /* MC_EMEM_ARB_TIMING_WAP2PRE */
-					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
-					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
-					0x00000005 /* MC_EMEM_ARB_TIMING_R2W */
-					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
-					0x06050202 /* MC_EMEM_ARB_DA_TURNS */
-					0x0010090d /* MC_EMEM_ARB_DA_COVERS */
-					0x7428180e /* MC_EMEM_ARB_MISC0 */
-					0x70000f03 /* MC_EMEM_ARB_MISC1 */
-					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-				>;
-			};
-
-			timing-600000000 {
-				clock-frequency = <600000000>;
-
-				nvidia,emem-configuration = <
-					0x00000009 /* MC_EMEM_ARB_CFG */
-					0x80000040 /* MC_EMEM_ARB_OUTSTANDING_REQ */
-					0x00000003 /* MC_EMEM_ARB_TIMING_RCD */
-					0x00000004 /* MC_EMEM_ARB_TIMING_RP */
-					0x0000000e /* MC_EMEM_ARB_TIMING_RC */
-					0x00000009 /* MC_EMEM_ARB_TIMING_RAS */
-					0x0000000b /* MC_EMEM_ARB_TIMING_FAW */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
-					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-					0x0000000b /* MC_EMEM_ARB_TIMING_WAP2PRE */
-					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
-					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
-					0x00000005 /* MC_EMEM_ARB_TIMING_R2W */
-					0x00000007 /* MC_EMEM_ARB_TIMING_W2R */
-					0x07050202 /* MC_EMEM_ARB_DA_TURNS */
-					0x00130b0e /* MC_EMEM_ARB_DA_COVERS */
-					0x73a91b0f /* MC_EMEM_ARB_MISC0 */
-					0x70000f03 /* MC_EMEM_ARB_MISC1 */
-					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-				>;
-			};
-
-			timing-792000000 {
-				clock-frequency = <792000000>;
-
-				nvidia,emem-configuration = <
-					0x0e00000b /* MC_EMEM_ARB_CFG */
-					0x80000040 /* MC_EMEM_ARB_OUTSTANDING_REQ */
-					0x00000004 /* MC_EMEM_ARB_TIMING_RCD */
-					0x00000005 /* MC_EMEM_ARB_TIMING_RP */
-					0x00000013 /* MC_EMEM_ARB_TIMING_RC */
-					0x0000000c /* MC_EMEM_ARB_TIMING_RAS */
-					0x0000000f /* MC_EMEM_ARB_TIMING_FAW */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RRD */
-					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-					0x0000000c /* MC_EMEM_ARB_TIMING_WAP2PRE */
-					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
-					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
-					0x00000006 /* MC_EMEM_ARB_TIMING_R2W */
-					0x00000008 /* MC_EMEM_ARB_TIMING_W2R */
-					0x08060202 /* MC_EMEM_ARB_DA_TURNS */
-					0x00160d13 /* MC_EMEM_ARB_DA_COVERS */
-					0x734c2414 /* MC_EMEM_ARB_MISC0 */
-					0x70000f02 /* MC_EMEM_ARB_MISC1 */
-					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-				>;
-			};
-		};
-
-		emc-timings-4 {
-			nvidia,ram-code = <4>;
-
-			timing-12750000 {
-				clock-frequency = <12750000>;
-
-				nvidia,emem-configuration = <
-					0x40040001 /* MC_EMEM_ARB_CFG */
-					0x8000000a /* MC_EMEM_ARB_OUTSTANDING_REQ */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RC */
-					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
-					0x00000002 /* MC_EMEM_ARB_TIMING_FAW */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
-					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
-					0x00000003 /* MC_EMEM_ARB_TIMING_R2R */
-					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
-					0x00000003 /* MC_EMEM_ARB_TIMING_R2W */
-					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
-					0x06030203 /* MC_EMEM_ARB_DA_TURNS */
-					0x000a0502 /* MC_EMEM_ARB_DA_COVERS */
-					0x77e30303 /* MC_EMEM_ARB_MISC0 */
-					0x70000f03 /* MC_EMEM_ARB_MISC1 */
-					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-				>;
-			};
-
-			timing-20400000 {
-				clock-frequency = <20400000>;
-
-				nvidia,emem-configuration = <
-					0x40020001 /* MC_EMEM_ARB_CFG */
-					0x80000012 /* MC_EMEM_ARB_OUTSTANDING_REQ */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RC */
-					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
-					0x00000002 /* MC_EMEM_ARB_TIMING_FAW */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
-					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
-					0x00000003 /* MC_EMEM_ARB_TIMING_R2R */
-					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
-					0x00000003 /* MC_EMEM_ARB_TIMING_R2W */
-					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
-					0x06030203 /* MC_EMEM_ARB_DA_TURNS */
-					0x000a0502 /* MC_EMEM_ARB_DA_COVERS */
-					0x77430303 /* MC_EMEM_ARB_MISC0 */
-					0x70000f03 /* MC_EMEM_ARB_MISC1 */
-					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-				>;
-			};
-
-			timing-40800000 {
-				clock-frequency = <40800000>;
-
-				nvidia,emem-configuration = <
-					0xa0000001 /* MC_EMEM_ARB_CFG */
-					0x80000017 /* MC_EMEM_ARB_OUTSTANDING_REQ */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RC */
-					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
-					0x00000002 /* MC_EMEM_ARB_TIMING_FAW */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
-					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
-					0x00000003 /* MC_EMEM_ARB_TIMING_R2R */
-					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
-					0x00000003 /* MC_EMEM_ARB_TIMING_R2W */
-					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
-					0x06030203 /* MC_EMEM_ARB_DA_TURNS */
-					0x000a0502 /* MC_EMEM_ARB_DA_COVERS */
-					0x75e30303 /* MC_EMEM_ARB_MISC0 */
-					0x70000f03 /* MC_EMEM_ARB_MISC1 */
-					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-				>;
-			};
-
-			timing-68000000 {
-				clock-frequency = <68000000>;
-
-				nvidia,emem-configuration = <
-					0x00000001 /* MC_EMEM_ARB_CFG */
-					0x8000001e /* MC_EMEM_ARB_OUTSTANDING_REQ */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RC */
-					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
-					0x00000002 /* MC_EMEM_ARB_TIMING_FAW */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
-					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
-					0x00000003 /* MC_EMEM_ARB_TIMING_R2R */
-					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
-					0x00000003 /* MC_EMEM_ARB_TIMING_R2W */
-					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
-					0x06030203 /* MC_EMEM_ARB_DA_TURNS */
-					0x000a0502 /* MC_EMEM_ARB_DA_COVERS */
-					0x75430403 /* MC_EMEM_ARB_MISC0 */
-					0x70000f03 /* MC_EMEM_ARB_MISC1 */
-					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-				>;
-			};
-
-			timing-102000000 {
-				clock-frequency = <102000000>;
-
-				nvidia,emem-configuration = <
-					0x08000001 /* MC_EMEM_ARB_CFG */
-					0x80000026 /* MC_EMEM_ARB_OUTSTANDING_REQ */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
-					0x00000003 /* MC_EMEM_ARB_TIMING_RC */
-					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
-					0x00000002 /* MC_EMEM_ARB_TIMING_FAW */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
-					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
-					0x00000003 /* MC_EMEM_ARB_TIMING_R2R */
-					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
-					0x00000003 /* MC_EMEM_ARB_TIMING_R2W */
-					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
-					0x06030203 /* MC_EMEM_ARB_DA_TURNS */
-					0x000a0503 /* MC_EMEM_ARB_DA_COVERS */
-					0x74e30504 /* MC_EMEM_ARB_MISC0 */
-					0x70000f03 /* MC_EMEM_ARB_MISC1 */
-					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-				>;
-			};
-
-			timing-204000000 {
-				clock-frequency = <204000000>;
-
-				nvidia,emem-configuration = <
-					0x01000003 /* MC_EMEM_ARB_CFG */
-					0x80000040 /* MC_EMEM_ARB_OUTSTANDING_REQ */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
-					0x00000004 /* MC_EMEM_ARB_TIMING_RC */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RAS */
-					0x00000004 /* MC_EMEM_ARB_TIMING_FAW */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
-					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
-					0x00000003 /* MC_EMEM_ARB_TIMING_R2R */
-					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
-					0x00000004 /* MC_EMEM_ARB_TIMING_R2W */
-					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
-					0x06040203 /* MC_EMEM_ARB_DA_TURNS */
-					0x000a0504 /* MC_EMEM_ARB_DA_COVERS */
-					0x74a40a05 /* MC_EMEM_ARB_MISC0 */
-					0x70000f03 /* MC_EMEM_ARB_MISC1 */
-					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-				>;
-			};
-
-			timing-300000000 {
-				clock-frequency = <300000000>;
-
-				nvidia,emem-configuration = <
-					0x08000004 /* MC_EMEM_ARB_CFG */
-					0x80000040 /* MC_EMEM_ARB_OUTSTANDING_REQ */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RP */
-					0x00000007 /* MC_EMEM_ARB_TIMING_RC */
-					0x00000004 /* MC_EMEM_ARB_TIMING_RAS */
-					0x00000005 /* MC_EMEM_ARB_TIMING_FAW */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-					0x00000007 /* MC_EMEM_ARB_TIMING_WAP2PRE */
-					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
-					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
-					0x00000004 /* MC_EMEM_ARB_TIMING_R2W */
-					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
-					0x06040202 /* MC_EMEM_ARB_DA_TURNS */
-					0x000b0607 /* MC_EMEM_ARB_DA_COVERS */
-					0x77450e08 /* MC_EMEM_ARB_MISC0 */
-					0x70000f03 /* MC_EMEM_ARB_MISC1 */
-					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-				>;
-			};
-
-			timing-396000000 {
-				clock-frequency = <396000000>;
-
-				nvidia,emem-configuration = <
-					0x0f000005 /* MC_EMEM_ARB_CFG */
-					0x80000040 /* MC_EMEM_ARB_OUTSTANDING_REQ */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RP */
-					0x00000009 /* MC_EMEM_ARB_TIMING_RC */
-					0x00000005 /* MC_EMEM_ARB_TIMING_RAS */
-					0x00000007 /* MC_EMEM_ARB_TIMING_FAW */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
-					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
-					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
-					0x00000004 /* MC_EMEM_ARB_TIMING_R2W */
-					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
-					0x06040202 /* MC_EMEM_ARB_DA_TURNS */
-					0x000d0709 /* MC_EMEM_ARB_DA_COVERS */
-					0x7586120a /* MC_EMEM_ARB_MISC0 */
-					0x70000f03 /* MC_EMEM_ARB_MISC1 */
-					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-				>;
-			};
-
-			timing-528000000 {
-				clock-frequency = <528000000>;
-
-				nvidia,emem-configuration = <
-					0x0f000007 /* MC_EMEM_ARB_CFG */
-					0x80000040 /* MC_EMEM_ARB_OUTSTANDING_REQ */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RCD */
-					0x00000003 /* MC_EMEM_ARB_TIMING_RP */
-					0x0000000c /* MC_EMEM_ARB_TIMING_RC */
-					0x00000007 /* MC_EMEM_ARB_TIMING_RAS */
-					0x0000000a /* MC_EMEM_ARB_TIMING_FAW */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-					0x00000009 /* MC_EMEM_ARB_TIMING_WAP2PRE */
-					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
-					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
-					0x00000005 /* MC_EMEM_ARB_TIMING_R2W */
-					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
-					0x06050202 /* MC_EMEM_ARB_DA_TURNS */
-					0x0010090c /* MC_EMEM_ARB_DA_COVERS */
-					0x7488180d /* MC_EMEM_ARB_MISC0 */
-					0x70000f03 /* MC_EMEM_ARB_MISC1 */
-					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-				>;
-			};
-
-			timing-600000000 {
-				clock-frequency = <600000000>;
-
-				nvidia,emem-configuration = <
-					0x00000009 /* MC_EMEM_ARB_CFG */
-					0x80000040 /* MC_EMEM_ARB_OUTSTANDING_REQ */
-					0x00000003 /* MC_EMEM_ARB_TIMING_RCD */
-					0x00000004 /* MC_EMEM_ARB_TIMING_RP */
-					0x0000000e /* MC_EMEM_ARB_TIMING_RC */
-					0x00000009 /* MC_EMEM_ARB_TIMING_RAS */
-					0x0000000b /* MC_EMEM_ARB_TIMING_FAW */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
-					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-					0x0000000b /* MC_EMEM_ARB_TIMING_WAP2PRE */
-					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
-					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
-					0x00000005 /* MC_EMEM_ARB_TIMING_R2W */
-					0x00000007 /* MC_EMEM_ARB_TIMING_W2R */
-					0x07050202 /* MC_EMEM_ARB_DA_TURNS */
-					0x00130b0e /* MC_EMEM_ARB_DA_COVERS */
-					0x74691b0f /* MC_EMEM_ARB_MISC0 */
-					0x70000f03 /* MC_EMEM_ARB_MISC1 */
-					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-				>;
-			};
-
-			timing-792000000 {
-				clock-frequency = <792000000>;
-
-				nvidia,emem-configuration = <
-					0x0e00000b /* MC_EMEM_ARB_CFG */
-					0x80000040 /* MC_EMEM_ARB_OUTSTANDING_REQ */
-					0x00000004 /* MC_EMEM_ARB_TIMING_RCD */
-					0x00000005 /* MC_EMEM_ARB_TIMING_RP */
-					0x00000013 /* MC_EMEM_ARB_TIMING_RC */
-					0x0000000c /* MC_EMEM_ARB_TIMING_RAS */
-					0x0000000f /* MC_EMEM_ARB_TIMING_FAW */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RRD */
-					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-					0x0000000c /* MC_EMEM_ARB_TIMING_WAP2PRE */
-					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
-					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
-					0x00000006 /* MC_EMEM_ARB_TIMING_R2W */
-					0x00000008 /* MC_EMEM_ARB_TIMING_W2R */
-					0x08060202 /* MC_EMEM_ARB_DA_TURNS */
-					0x00170e13 /* MC_EMEM_ARB_DA_COVERS */
-					0x746c2414 /* MC_EMEM_ARB_MISC0 */
-					0x70000f02 /* MC_EMEM_ARB_MISC1 */
-					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-				>;
-			};
-		};
-
-		emc-timings-6 {
-			nvidia,ram-code = <6>;
-
-			timing-12750000 {
-				clock-frequency = <12750000>;
-
-				nvidia,emem-configuration = <
-					0x40040001 /* MC_EMEM_ARB_CFG */
-					0x8000000a /* MC_EMEM_ARB_OUTSTANDING_REQ */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RC */
-					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
-					0x00000002 /* MC_EMEM_ARB_TIMING_FAW */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
-					0x00000003 /* MC_EMEM_ARB_TIMING_R2R */
-					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
-					0x00000003 /* MC_EMEM_ARB_TIMING_R2W */
-					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
-					0x06030203 /* MC_EMEM_ARB_DA_TURNS */
-					0x000a0402 /* MC_EMEM_ARB_DA_COVERS */
-					0x77e30303 /* MC_EMEM_ARB_MISC0 */
-					0x70000f03 /* MC_EMEM_ARB_MISC1 */
-					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-				>;
-			};
-
-			timing-20400000 {
-				clock-frequency = <20400000>;
-
-				nvidia,emem-configuration = <
-					0x40020001 /* MC_EMEM_ARB_CFG */
-					0x80000012 /* MC_EMEM_ARB_OUTSTANDING_REQ */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RC */
-					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
-					0x00000002 /* MC_EMEM_ARB_TIMING_FAW */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
-					0x00000003 /* MC_EMEM_ARB_TIMING_R2R */
-					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
-					0x00000003 /* MC_EMEM_ARB_TIMING_R2W */
-					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
-					0x06030203 /* MC_EMEM_ARB_DA_TURNS */
-					0x000a0402 /* MC_EMEM_ARB_DA_COVERS */
-					0x76230303 /* MC_EMEM_ARB_MISC0 */
-					0x70000f03 /* MC_EMEM_ARB_MISC1 */
-					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-				>;
-			};
-
-			timing-40800000 {
-				clock-frequency = <40800000>;
-
-				nvidia,emem-configuration = <
-					0xa0000001 /* MC_EMEM_ARB_CFG */
-					0x80000017 /* MC_EMEM_ARB_OUTSTANDING_REQ */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RC */
-					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
-					0x00000002 /* MC_EMEM_ARB_TIMING_FAW */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
-					0x00000003 /* MC_EMEM_ARB_TIMING_R2R */
-					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
-					0x00000003 /* MC_EMEM_ARB_TIMING_R2W */
-					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
-					0x06030203 /* MC_EMEM_ARB_DA_TURNS */
-					0x000a0402 /* MC_EMEM_ARB_DA_COVERS */
-					0x74a30303 /* MC_EMEM_ARB_MISC0 */
-					0x70000f03 /* MC_EMEM_ARB_MISC1 */
-					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-				>;
-			};
-
-			timing-68000000 {
-				clock-frequency = <68000000>;
-
-				nvidia,emem-configuration = <
-					0x00000001 /* MC_EMEM_ARB_CFG */
-					0x8000001e /* MC_EMEM_ARB_OUTSTANDING_REQ */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RC */
-					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
-					0x00000002 /* MC_EMEM_ARB_TIMING_FAW */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
-					0x00000003 /* MC_EMEM_ARB_TIMING_R2R */
-					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
-					0x00000003 /* MC_EMEM_ARB_TIMING_R2W */
-					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
-					0x06030203 /* MC_EMEM_ARB_DA_TURNS */
-					0x000a0402 /* MC_EMEM_ARB_DA_COVERS */
-					0x74230403 /* MC_EMEM_ARB_MISC0 */
-					0x70000f03 /* MC_EMEM_ARB_MISC1 */
-					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-				>;
-			};
-
-			timing-102000000 {
-				clock-frequency = <102000000>;
-
-				nvidia,emem-configuration = <
-					0x08000001 /* MC_EMEM_ARB_CFG */
-					0x80000026 /* MC_EMEM_ARB_OUTSTANDING_REQ */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
-					0x00000003 /* MC_EMEM_ARB_TIMING_RC */
-					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
-					0x00000002 /* MC_EMEM_ARB_TIMING_FAW */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
-					0x00000003 /* MC_EMEM_ARB_TIMING_R2R */
-					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
-					0x00000003 /* MC_EMEM_ARB_TIMING_R2W */
-					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
-					0x06030203 /* MC_EMEM_ARB_DA_TURNS */
-					0x000a0403 /* MC_EMEM_ARB_DA_COVERS */
-					0x73c30504 /* MC_EMEM_ARB_MISC0 */
-					0x70000f03 /* MC_EMEM_ARB_MISC1 */
-					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-				>;
-			};
-
-			timing-204000000 {
-				clock-frequency = <204000000>;
-
-				nvidia,emem-configuration = <
-					0x01000003 /* MC_EMEM_ARB_CFG */
-					0x80000040 /* MC_EMEM_ARB_OUTSTANDING_REQ */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
-					0x00000005 /* MC_EMEM_ARB_TIMING_RC */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RAS */
-					0x00000004 /* MC_EMEM_ARB_TIMING_FAW */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
-					0x00000003 /* MC_EMEM_ARB_TIMING_R2R */
-					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
-					0x00000004 /* MC_EMEM_ARB_TIMING_R2W */
-					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
-					0x06040203 /* MC_EMEM_ARB_DA_TURNS */
-					0x000a0405 /* MC_EMEM_ARB_DA_COVERS */
-					0x73840a06 /* MC_EMEM_ARB_MISC0 */
-					0x70000f03 /* MC_EMEM_ARB_MISC1 */
-					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-				>;
-			};
-
-			timing-300000000 {
-				clock-frequency = <300000000>;
-
-				nvidia,emem-configuration = <
-					0x08000004 /* MC_EMEM_ARB_CFG */
-					0x80000040 /* MC_EMEM_ARB_OUTSTANDING_REQ */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RP */
-					0x00000007 /* MC_EMEM_ARB_TIMING_RC */
-					0x00000004 /* MC_EMEM_ARB_TIMING_RAS */
-					0x00000005 /* MC_EMEM_ARB_TIMING_FAW */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-					0x00000007 /* MC_EMEM_ARB_TIMING_WAP2PRE */
-					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
-					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
-					0x00000004 /* MC_EMEM_ARB_TIMING_R2W */
-					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
-					0x06040202 /* MC_EMEM_ARB_DA_TURNS */
-					0x000b0607 /* MC_EMEM_ARB_DA_COVERS */
-					0x77450e08 /* MC_EMEM_ARB_MISC0 */
-					0x70000f03 /* MC_EMEM_ARB_MISC1 */
-					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-				>;
-			};
-
-			timing-396000000 {
-				clock-frequency = <396000000>;
-
-				nvidia,emem-configuration = <
-					0x0f000005 /* MC_EMEM_ARB_CFG */
-					0x80000040 /* MC_EMEM_ARB_OUTSTANDING_REQ */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RP */
-					0x00000009 /* MC_EMEM_ARB_TIMING_RC */
-					0x00000005 /* MC_EMEM_ARB_TIMING_RAS */
-					0x00000007 /* MC_EMEM_ARB_TIMING_FAW */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
-					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
-					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
-					0x00000004 /* MC_EMEM_ARB_TIMING_R2W */
-					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
-					0x06040202 /* MC_EMEM_ARB_DA_TURNS */
-					0x000d0709 /* MC_EMEM_ARB_DA_COVERS */
-					0x7586120a /* MC_EMEM_ARB_MISC0 */
-					0x70000f03 /* MC_EMEM_ARB_MISC1 */
-					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-				>;
-			};
-
-			timing-528000000 {
-				clock-frequency = <528000000>;
-
-				nvidia,emem-configuration = <
-					0x0f000007 /* MC_EMEM_ARB_CFG */
-					0x80000040 /* MC_EMEM_ARB_OUTSTANDING_REQ */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RCD */
-					0x00000003 /* MC_EMEM_ARB_TIMING_RP */
-					0x0000000d /* MC_EMEM_ARB_TIMING_RC */
-					0x00000008 /* MC_EMEM_ARB_TIMING_RAS */
-					0x0000000a /* MC_EMEM_ARB_TIMING_FAW */
-					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-					0x00000009 /* MC_EMEM_ARB_TIMING_WAP2PRE */
-					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
-					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
-					0x00000005 /* MC_EMEM_ARB_TIMING_R2W */
-					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
-					0x06050202 /* MC_EMEM_ARB_DA_TURNS */
-					0x0010090d /* MC_EMEM_ARB_DA_COVERS */
-					0x7428180e /* MC_EMEM_ARB_MISC0 */
-					0x70000f03 /* MC_EMEM_ARB_MISC1 */
-					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-				>;
-			};
-
-			timing-600000000 {
-				clock-frequency = <600000000>;
-
-				nvidia,emem-configuration = <
-					0x00000009 /* MC_EMEM_ARB_CFG */
-					0x80000040 /* MC_EMEM_ARB_OUTSTANDING_REQ */
-					0x00000003 /* MC_EMEM_ARB_TIMING_RCD */
-					0x00000004 /* MC_EMEM_ARB_TIMING_RP */
-					0x0000000e /* MC_EMEM_ARB_TIMING_RC */
-					0x00000009 /* MC_EMEM_ARB_TIMING_RAS */
-					0x0000000b /* MC_EMEM_ARB_TIMING_FAW */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RRD */
-					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-					0x0000000b /* MC_EMEM_ARB_TIMING_WAP2PRE */
-					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
-					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
-					0x00000005 /* MC_EMEM_ARB_TIMING_R2W */
-					0x00000007 /* MC_EMEM_ARB_TIMING_W2R */
-					0x07050202 /* MC_EMEM_ARB_DA_TURNS */
-					0x00130b0e /* MC_EMEM_ARB_DA_COVERS */
-					0x73a91b0f /* MC_EMEM_ARB_MISC0 */
-					0x70000f03 /* MC_EMEM_ARB_MISC1 */
-					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-				>;
-			};
-
-			timing-792000000 {
-				clock-frequency = <792000000>;
-
-				nvidia,emem-configuration = <
-					0x0e00000b /* MC_EMEM_ARB_CFG */
-					0x80000040 /* MC_EMEM_ARB_OUTSTANDING_REQ */
-					0x00000004 /* MC_EMEM_ARB_TIMING_RCD */
-					0x00000005 /* MC_EMEM_ARB_TIMING_RP */
-					0x00000013 /* MC_EMEM_ARB_TIMING_RC */
-					0x0000000c /* MC_EMEM_ARB_TIMING_RAS */
-					0x0000000f /* MC_EMEM_ARB_TIMING_FAW */
-					0x00000002 /* MC_EMEM_ARB_TIMING_RRD */
-					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-					0x0000000c /* MC_EMEM_ARB_TIMING_WAP2PRE */
-					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
-					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
-					0x00000006 /* MC_EMEM_ARB_TIMING_R2W */
-					0x00000008 /* MC_EMEM_ARB_TIMING_W2R */
-					0x08060202 /* MC_EMEM_ARB_DA_TURNS */
-					0x00160d13 /* MC_EMEM_ARB_DA_COVERS */
-					0x734c2414 /* MC_EMEM_ARB_MISC0 */
-					0x70000f02 /* MC_EMEM_ARB_MISC1 */
-					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-				>;
-			};
-		};
-	};
 };
 
 &emc_icc_dvfs_opp_table {
-	/delete-node/ opp@924000000,1100;
-	/delete-node/ opp@1200000000,1100;
+	/delete-node/ opp-924000000-1100;
+	/delete-node/ opp-1200000000-1100;
 };
 
 &emc_bw_dfs_opp_table {
-	/delete-node/ opp@924000000;
-	/delete-node/ opp@1200000000;
+	/delete-node/ opp-924000000;
+	/delete-node/ opp-1200000000;
 };
diff --git a/arch/arm/boot/dts/tegra124-nyan-big-fhd.dts b/arch/arm/boot/dts/tegra124-nyan-big-fhd.dts
new file mode 100644
index 000000000000..4db43324dafa
--- /dev/null
+++ b/arch/arm/boot/dts/tegra124-nyan-big-fhd.dts
@@ -0,0 +1,17 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include "tegra124-nyan-big.dts"
+
+/ {
+	/* Version of Nyan Big with 1080p panel */
+	host1x@50000000 {
+		dpaux@545c0000 {
+			aux-bus {
+				panel: panel {
+					compatible = "auo,b133htn01";
+				};
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/tegra124-nyan-big.dts b/arch/arm/boot/dts/tegra124-nyan-big.dts
index 1d2aac2cb6d0..fdc1d64dfff9 100644
--- a/arch/arm/boot/dts/tegra124-nyan-big.dts
+++ b/arch/arm/boot/dts/tegra124-nyan-big.dts
@@ -13,12 +13,15 @@
 		     "google,nyan-big-rev1", "google,nyan-big-rev0",
 		     "google,nyan-big", "google,nyan", "nvidia,tegra124";
 
-	panel: panel {
-		compatible = "auo,b133xtn01";
-
-		power-supply = <&vdd_3v3_panel>;
-		backlight = <&backlight>;
-		ddc-i2c-bus = <&dpaux>;
+	host1x@50000000 {
+		dpaux@545c0000 {
+			aux-bus {
+				panel: panel {
+					compatible = "auo,b133xtn01";
+					backlight = <&backlight>;
+				};
+			};
+		};
 	};
 
 	mmc@700b0400 { /* SD Card on this bus */
diff --git a/arch/arm/boot/dts/tegra124-nyan-blaze-emc.dtsi b/arch/arm/boot/dts/tegra124-nyan-blaze-emc.dtsi
index 35c98734d35f..2ce1b12be44d 100644
--- a/arch/arm/boot/dts/tegra124-nyan-blaze-emc.dtsi
+++ b/arch/arm/boot/dts/tegra124-nyan-blaze-emc.dtsi
@@ -10,55 +10,65 @@
 				clocks = <&tegra_car TEGRA124_CLK_PLL_P>;
 				clock-names = "emc-parent";
 			};
+
 			timing-20400000 {
 				clock-frequency = <20400000>;
 				nvidia,parent-clock-frequency = <408000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_P>;
 				clock-names = "emc-parent";
 			};
+
 			timing-40800000 {
 				clock-frequency = <40800000>;
 				nvidia,parent-clock-frequency = <408000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_P>;
 				clock-names = "emc-parent";
 			};
+
 			timing-68000000 {
 				clock-frequency = <68000000>;
 				nvidia,parent-clock-frequency = <408000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_P>;
 				clock-names = "emc-parent";
 			};
+
 			timing-102000000 {
 				clock-frequency = <102000000>;
 				nvidia,parent-clock-frequency = <408000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_P>;
 				clock-names = "emc-parent";
 			};
+
 			timing-204000000 {
 				clock-frequency = <204000000>;
 				nvidia,parent-clock-frequency = <408000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_P>;
 				clock-names = "emc-parent";
 			};
+
 			timing-300000000 {
 				clock-frequency = <300000000>;
 				nvidia,parent-clock-frequency = <600000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_C>;
 				clock-names = "emc-parent";
 			};
+
 			timing-396000000 {
 				clock-frequency = <396000000>;
 				nvidia,parent-clock-frequency = <792000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_M>;
 				clock-names = "emc-parent";
 			};
+
 			/* TODO: Add 528MHz frequency */
+
 			timing-600000000 {
 				clock-frequency = <600000000>;
 				nvidia,parent-clock-frequency = <600000000>;
 				clocks = <&tegra_car TEGRA124_CLK_PLL_C_UD>;
 				clock-names = "emc-parent";
 			};
+
 			timing-792000000 {
 				clock-frequency = <792000000>;
 				nvidia,parent-clock-frequency = <792000000>;
@@ -68,6 +78,298 @@
 		};
 	};
 
+	memory-controller@70019000 {
+		emc-timings-1 {
+			nvidia,ram-code = <1>;
+
+			timing-12750000 {
+				clock-frequency = <12750000>;
+
+				nvidia,emem-configuration = <
+					0x40040001
+					0x8000000a
+					0x00000001
+					0x00000001
+					0x00000002
+					0x00000000
+					0x00000002
+					0x00000001
+					0x00000002
+					0x00000008
+					0x00000003
+					0x00000002
+					0x00000003
+					0x00000006
+					0x06030203
+					0x000a0402
+					0x77e30303
+					0x70000f03
+					0x001f0000
+				>;
+			};
+
+			timing-20400000 {
+				clock-frequency = <20400000>;
+
+				nvidia,emem-configuration = <
+					0x40020001
+					0x80000012
+					0x00000001
+					0x00000001
+					0x00000002
+					0x00000000
+					0x00000002
+					0x00000001
+					0x00000002
+					0x00000008
+					0x00000003
+					0x00000002
+					0x00000003
+					0x00000006
+					0x06030203
+					0x000a0402
+					0x76230303
+					0x70000f03
+					0x001f0000
+				>;
+			};
+
+			timing-40800000 {
+				clock-frequency = <40800000>;
+
+				nvidia,emem-configuration = <
+					0xa0000001
+					0x80000017
+					0x00000001
+					0x00000001
+					0x00000002
+					0x00000000
+					0x00000002
+					0x00000001
+					0x00000002
+					0x00000008
+					0x00000003
+					0x00000002
+					0x00000003
+					0x00000006
+					0x06030203
+					0x000a0402
+					0x74a30303
+					0x70000f03
+					0x001f0000
+				>;
+			};
+
+			timing-68000000 {
+				clock-frequency = <68000000>;
+
+				nvidia,emem-configuration = <
+					0x00000001
+					0x8000001e
+					0x00000001
+					0x00000001
+					0x00000002
+					0x00000000
+					0x00000002
+					0x00000001
+					0x00000002
+					0x00000008
+					0x00000003
+					0x00000002
+					0x00000003
+					0x00000006
+					0x06030203
+					0x000a0402
+					0x74230403
+					0x70000f03
+					0x001f0000
+				>;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emem-configuration = <
+					0x08000001
+					0x80000026
+					0x00000001
+					0x00000001
+					0x00000003
+					0x00000000
+					0x00000002
+					0x00000001
+					0x00000002
+					0x00000008
+					0x00000003
+					0x00000002
+					0x00000003
+					0x00000006
+					0x06030203
+					0x000a0403
+					0x73c30504
+					0x70000f03
+					0x001f0000
+				>;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emem-configuration = <
+					0x01000003
+					0x80000040
+					0x00000001
+					0x00000001
+					0x00000005
+					0x00000002
+					0x00000004
+					0x00000001
+					0x00000002
+					0x00000008
+					0x00000003
+					0x00000002
+					0x00000004
+					0x00000006
+					0x06040203
+					0x000a0405
+					0x73840a06
+					0x70000f03
+					0x001f0000
+				>;
+			};
+
+			timing-300000000 {
+				clock-frequency = <300000000>;
+
+				nvidia,emem-configuration = <
+					0x08000004
+					0x80000040
+					0x00000001
+					0x00000002
+					0x00000007
+					0x00000004
+					0x00000005
+					0x00000001
+					0x00000002
+					0x00000007
+					0x00000002
+					0x00000002
+					0x00000004
+					0x00000006
+					0x06040202
+					0x000b0607
+					0x77450e08
+					0x70000f03
+					0x001f0000
+				>;
+			};
+
+			timing-396000000 {
+				clock-frequency = <396000000>;
+
+				nvidia,emem-configuration = <
+					0x0f000005
+					0x80000040
+					0x00000001
+					0x00000002
+					0x00000009
+					0x00000005
+					0x00000007
+					0x00000001
+					0x00000002
+					0x00000008
+					0x00000002
+					0x00000002
+					0x00000004
+					0x00000006
+					0x06040202
+					0x000d0709
+					0x7586120a
+					0x70000f03
+					0x001f0000
+				>;
+			};
+
+			timing-528000000 {
+				clock-frequency = <528000000>;
+
+				nvidia,emem-configuration = <
+					0x0f000007
+					0x80000040
+					0x00000002
+					0x00000003
+					0x0000000d
+					0x00000008
+					0x0000000a
+					0x00000001
+					0x00000002
+					0x00000009
+					0x00000002
+					0x00000002
+					0x00000005
+					0x00000006
+					0x06050202
+					0x0010090d
+					0x7428180e
+					0x70000f03
+					0x001f0000
+				>;
+			};
+
+			timing-600000000 {
+				clock-frequency = <600000000>;
+
+				nvidia,emem-configuration = <
+					0x00000009
+					0x80000040
+					0x00000003
+					0x00000004
+					0x0000000e
+					0x00000009
+					0x0000000b
+					0x00000001
+					0x00000003
+					0x0000000b
+					0x00000002
+					0x00000002
+					0x00000005
+					0x00000007
+					0x07050202
+					0x00130b0e
+					0x73a91b0f
+					0x70000f03
+					0x001f0000
+				>;
+			};
+
+			timing-792000000 {
+				clock-frequency = <792000000>;
+
+				nvidia,emem-configuration = <
+					0x0e00000b
+					0x80000040
+					0x00000004
+					0x00000005
+					0x00000013
+					0x0000000c
+					0x0000000f
+					0x00000002
+					0x00000003
+					0x0000000c
+					0x00000002
+					0x00000002
+					0x00000006
+					0x00000008
+					0x08060202
+					0x00160d13
+					0x734c2414
+					0x70000f02
+					0x001f0000
+				>;
+			};
+		};
+	};
+
 	external-memory-controller@7001b000 {
 		emc-timings-1 {
 			nvidia,ram-code = <1>;
@@ -1751,310 +2053,16 @@
 					0x0000000f
 				>;
 			};
-
-		};
-	};
-
-	memory-controller@70019000 {
-		emc-timings-1 {
-			nvidia,ram-code = <1>;
-
-
-			timing-12750000 {
-				clock-frequency = <12750000>;
-
-				nvidia,emem-configuration = <
-					0x40040001
-					0x8000000a
-					0x00000001
-					0x00000001
-					0x00000002
-					0x00000000
-					0x00000002
-					0x00000001
-					0x00000002
-					0x00000008
-					0x00000003
-					0x00000002
-					0x00000003
-					0x00000006
-					0x06030203
-					0x000a0402
-					0x77e30303
-					0x70000f03
-					0x001f0000
-				>;
-			};
-
-			timing-20400000 {
-				clock-frequency = <20400000>;
-
-				nvidia,emem-configuration = <
-					0x40020001
-					0x80000012
-					0x00000001
-					0x00000001
-					0x00000002
-					0x00000000
-					0x00000002
-					0x00000001
-					0x00000002
-					0x00000008
-					0x00000003
-					0x00000002
-					0x00000003
-					0x00000006
-					0x06030203
-					0x000a0402
-					0x76230303
-					0x70000f03
-					0x001f0000
-				>;
-			};
-
-			timing-40800000 {
-				clock-frequency = <40800000>;
-
-				nvidia,emem-configuration = <
-					0xa0000001
-					0x80000017
-					0x00000001
-					0x00000001
-					0x00000002
-					0x00000000
-					0x00000002
-					0x00000001
-					0x00000002
-					0x00000008
-					0x00000003
-					0x00000002
-					0x00000003
-					0x00000006
-					0x06030203
-					0x000a0402
-					0x74a30303
-					0x70000f03
-					0x001f0000
-				>;
-			};
-
-			timing-68000000 {
-				clock-frequency = <68000000>;
-
-				nvidia,emem-configuration = <
-					0x00000001
-					0x8000001e
-					0x00000001
-					0x00000001
-					0x00000002
-					0x00000000
-					0x00000002
-					0x00000001
-					0x00000002
-					0x00000008
-					0x00000003
-					0x00000002
-					0x00000003
-					0x00000006
-					0x06030203
-					0x000a0402
-					0x74230403
-					0x70000f03
-					0x001f0000
-				>;
-			};
-
-			timing-102000000 {
-				clock-frequency = <102000000>;
-
-				nvidia,emem-configuration = <
-					0x08000001
-					0x80000026
-					0x00000001
-					0x00000001
-					0x00000003
-					0x00000000
-					0x00000002
-					0x00000001
-					0x00000002
-					0x00000008
-					0x00000003
-					0x00000002
-					0x00000003
-					0x00000006
-					0x06030203
-					0x000a0403
-					0x73c30504
-					0x70000f03
-					0x001f0000
-				>;
-			};
-
-			timing-204000000 {
-				clock-frequency = <204000000>;
-
-				nvidia,emem-configuration = <
-					0x01000003
-					0x80000040
-					0x00000001
-					0x00000001
-					0x00000005
-					0x00000002
-					0x00000004
-					0x00000001
-					0x00000002
-					0x00000008
-					0x00000003
-					0x00000002
-					0x00000004
-					0x00000006
-					0x06040203
-					0x000a0405
-					0x73840a06
-					0x70000f03
-					0x001f0000
-				>;
-			};
-
-			timing-300000000 {
-				clock-frequency = <300000000>;
-
-				nvidia,emem-configuration = <
-					0x08000004
-					0x80000040
-					0x00000001
-					0x00000002
-					0x00000007
-					0x00000004
-					0x00000005
-					0x00000001
-					0x00000002
-					0x00000007
-					0x00000002
-					0x00000002
-					0x00000004
-					0x00000006
-					0x06040202
-					0x000b0607
-					0x77450e08
-					0x70000f03
-					0x001f0000
-				>;
-			};
-
-			timing-396000000 {
-				clock-frequency = <396000000>;
-
-				nvidia,emem-configuration = <
-					0x0f000005
-					0x80000040
-					0x00000001
-					0x00000002
-					0x00000009
-					0x00000005
-					0x00000007
-					0x00000001
-					0x00000002
-					0x00000008
-					0x00000002
-					0x00000002
-					0x00000004
-					0x00000006
-					0x06040202
-					0x000d0709
-					0x7586120a
-					0x70000f03
-					0x001f0000
-				>;
-			};
-
-			timing-528000000 {
-				clock-frequency = <528000000>;
-
-				nvidia,emem-configuration = <
-					0x0f000007
-					0x80000040
-					0x00000002
-					0x00000003
-					0x0000000d
-					0x00000008
-					0x0000000a
-					0x00000001
-					0x00000002
-					0x00000009
-					0x00000002
-					0x00000002
-					0x00000005
-					0x00000006
-					0x06050202
-					0x0010090d
-					0x7428180e
-					0x70000f03
-					0x001f0000
-				>;
-			};
-
-			timing-600000000 {
-				clock-frequency = <600000000>;
-
-				nvidia,emem-configuration = <
-					0x00000009
-					0x80000040
-					0x00000003
-					0x00000004
-					0x0000000e
-					0x00000009
-					0x0000000b
-					0x00000001
-					0x00000003
-					0x0000000b
-					0x00000002
-					0x00000002
-					0x00000005
-					0x00000007
-					0x07050202
-					0x00130b0e
-					0x73a91b0f
-					0x70000f03
-					0x001f0000
-				>;
-			};
-
-			timing-792000000 {
-				clock-frequency = <792000000>;
-
-				nvidia,emem-configuration = <
-					0x0e00000b
-					0x80000040
-					0x00000004
-					0x00000005
-					0x00000013
-					0x0000000c
-					0x0000000f
-					0x00000002
-					0x00000003
-					0x0000000c
-					0x00000002
-					0x00000002
-					0x00000006
-					0x00000008
-					0x08060202
-					0x00160d13
-					0x734c2414
-					0x70000f02
-					0x001f0000
-				>;
-			};
 		};
 	};
 };
 
 &emc_icc_dvfs_opp_table {
-	/delete-node/ opp@924000000,1100;
-	/delete-node/ opp@1200000000,1100;
+	/delete-node/ opp-924000000-1100;
+	/delete-node/ opp-1200000000-1100;
 };
 
 &emc_bw_dfs_opp_table {
-	/delete-node/ opp@924000000;
-	/delete-node/ opp@1200000000;
+	/delete-node/ opp-924000000;
+	/delete-node/ opp-1200000000;
 };
diff --git a/arch/arm/boot/dts/tegra124-nyan-blaze.dts b/arch/arm/boot/dts/tegra124-nyan-blaze.dts
index 677babde6460..abdf4456826f 100644
--- a/arch/arm/boot/dts/tegra124-nyan-blaze.dts
+++ b/arch/arm/boot/dts/tegra124-nyan-blaze.dts
@@ -15,12 +15,15 @@
 		     "google,nyan-blaze-rev0", "google,nyan-blaze",
 		     "google,nyan", "nvidia,tegra124";
 
-	panel: panel {
-		compatible = "samsung,ltn140at29-301";
-
-		power-supply = <&vdd_3v3_panel>;
-		backlight = <&backlight>;
-		ddc-i2c-bus = <&dpaux>;
+	host1x@50000000 {
+		dpaux@545c0000 {
+			aux-bus {
+				panel: panel {
+					compatible = "samsung,ltn140at29-301";
+					backlight = <&backlight>;
+				};
+			};
+		};
 	};
 
 	sound {
diff --git a/arch/arm/boot/dts/tegra124-nyan.dtsi b/arch/arm/boot/dts/tegra124-nyan.dtsi
index 63a81270300a..13061ab5247b 100644
--- a/arch/arm/boot/dts/tegra124-nyan.dtsi
+++ b/arch/arm/boot/dts/tegra124-nyan.dtsi
@@ -1,5 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0
 #include <dt-bindings/input/input.h>
+#include <dt-bindings/thermal/thermal.h>
 #include "tegra124.dtsi"
 
 / {
@@ -61,7 +62,7 @@
 		};
 	};
 
-	gpu@0,57000000 {
+	gpu@57000000 {
 		status = "okay";
 
 		vdd-supply = <&vdd_gpu>;
@@ -87,7 +88,7 @@
 			interrupts = <TEGRA_GPIO(H, 4) IRQ_TYPE_EDGE_FALLING>;
 		};
 
-		temperature-sensor@4c {
+		tmp451: temperature-sensor@4c {
 			compatible = "ti,tmp451";
 			reg = <0x4c>;
 			interrupt-parent = <&gpio>;
@@ -390,6 +391,10 @@
 		nvidia,sys-clock-req-active-high;
 	};
 
+	cec@70015000 {
+		status = "okay";
+	};
+
 	hda@70030000 {
 		status = "okay";
 	};
@@ -466,6 +471,7 @@
 				vbus-supply = <&vdd_usb1_vbus>;
 				status = "okay";
 				mode = "otg";
+				usb-role-switch;
 			};
 
 			usb2-1 {
@@ -527,7 +533,7 @@
 
 	/* CPU DFLL clock */
 	clock@70110000 {
-		status = "disabled";
+		status = "okay";
 		vdd-cpu-supply = <&vdd_cpu>;
 		nvidia,i2c-fs-rate = <400000>;
 	};
@@ -582,7 +588,7 @@
 			 256>;
 	};
 
-	clk32k_in: clock@0 {
+	clk32k_in: clock-32k {
 		compatible = "fixed-clock";
 		clock-frequency = <32768>;
 		#clock-cells = <0>;
@@ -597,7 +603,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		lid {
+		switch-lid {
 			label = "Lid";
 			gpios = <&gpio TEGRA_GPIO(R, 4) GPIO_ACTIVE_LOW>;
 			linux,input-type = <5>;
@@ -606,7 +612,7 @@
 			wakeup-source;
 		};
 
-		power {
+		key-power {
 			label = "Power";
 			gpios = <&gpio TEGRA_GPIO(Q, 0) GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
@@ -615,7 +621,7 @@
 		};
 	};
 
-	vdd_mux: regulator@0 {
+	vdd_mux: regulator-mux {
 		compatible = "regulator-fixed";
 		regulator-name = "+VDD_MUX";
 		regulator-min-microvolt = <12000000>;
@@ -624,7 +630,7 @@
 		regulator-boot-on;
 	};
 
-	vdd_5v0_sys: regulator@1 {
+	vdd_5v0_sys: regulator-5v0sys {
 		compatible = "regulator-fixed";
 		regulator-name = "+5V_SYS";
 		regulator-min-microvolt = <5000000>;
@@ -634,7 +640,7 @@
 		vin-supply = <&vdd_mux>;
 	};
 
-	vdd_3v3_sys: regulator@2 {
+	vdd_3v3_sys: regulator-3v3sys {
 		compatible = "regulator-fixed";
 		regulator-name = "+3.3V_SYS";
 		regulator-min-microvolt = <3300000>;
@@ -644,7 +650,7 @@
 		vin-supply = <&vdd_mux>;
 	};
 
-	vdd_3v3_run: regulator@3 {
+	vdd_3v3_run: regulator-3v3run {
 		compatible = "regulator-fixed";
 		regulator-name = "+3.3V_RUN";
 		regulator-min-microvolt = <3300000>;
@@ -656,7 +662,7 @@
 		vin-supply = <&vdd_3v3_sys>;
 	};
 
-	vdd_3v3_hdmi: regulator@4 {
+	vdd_3v3_hdmi: regulator-3v3hdmi {
 		compatible = "regulator-fixed";
 		regulator-name = "+3.3V_AVDD_HDMI_AP_GATED";
 		regulator-min-microvolt = <3300000>;
@@ -664,7 +670,7 @@
 		vin-supply = <&vdd_3v3_run>;
 	};
 
-	vdd_led: regulator@5 {
+	vdd_led: regulator-led {
 		compatible = "regulator-fixed";
 		regulator-name = "+VDD_LED";
 		gpio = <&gpio TEGRA_GPIO(P, 2) GPIO_ACTIVE_HIGH>;
@@ -672,7 +678,7 @@
 		vin-supply = <&vdd_mux>;
 	};
 
-	vdd_5v0_ts: regulator@6 {
+	vdd_5v0_ts: regulator-ts {
 		compatible = "regulator-fixed";
 		regulator-name = "+5V_VDD_TS_SW";
 		regulator-min-microvolt = <5000000>;
@@ -683,7 +689,7 @@
 		vin-supply = <&vdd_5v0_sys>;
 	};
 
-	vdd_usb1_vbus: regulator@7 {
+	vdd_usb1_vbus: regulator-usb1 {
 		compatible = "regulator-fixed";
 		regulator-name = "+5V_USB_HS";
 		regulator-min-microvolt = <5000000>;
@@ -694,7 +700,7 @@
 		vin-supply = <&vdd_5v0_sys>;
 	};
 
-	vdd_usb3_vbus: regulator@8 {
+	vdd_usb3_vbus: regulator-usb3 {
 		compatible = "regulator-fixed";
 		regulator-name = "+5V_USB_SS";
 		regulator-min-microvolt = <5000000>;
@@ -705,7 +711,7 @@
 		vin-supply = <&vdd_5v0_sys>;
 	};
 
-	vdd_3v3_panel: regulator@9 {
+	vdd_3v3_panel: regulator-panel {
 		compatible = "regulator-fixed";
 		regulator-name = "+3.3V_PANEL";
 		regulator-min-microvolt = <3300000>;
@@ -715,7 +721,7 @@
 		vin-supply = <&vdd_3v3_run>;
 	};
 
-	vdd_3v3_lp0: regulator@10 {
+	vdd_3v3_lp0: regulator-lp0 {
 		compatible = "regulator-fixed";
 		regulator-name = "+3.3V_LP0";
 		regulator-min-microvolt = <3300000>;
@@ -730,7 +736,7 @@
 		vin-supply = <&vdd_3v3_sys>;
 	};
 
-	vdd_hdmi_pll: regulator@11 {
+	vdd_hdmi_pll: regulator-hdmipll {
 		compatible = "regulator-fixed";
 		regulator-name = "+1.05V_RUN_AVDD_HDMI_PLL";
 		regulator-min-microvolt = <1050000>;
@@ -739,7 +745,7 @@
 		vin-supply = <&vdd_1v05_run>;
 	};
 
-	vdd_5v0_hdmi: regulator@12 {
+	vdd_5v0_hdmi: regulator-hdmicon {
 		compatible = "regulator-fixed";
 		regulator-name = "+5V_HDMI_CON";
 		regulator-min-microvolt = <5000000>;
@@ -784,6 +790,52 @@
 		gpios = <&gpio TEGRA_GPIO(I, 5) GPIO_ACTIVE_LOW>;
 		priority = <200>;
 	};
+
+	cpus {
+		cpu0: cpu@0 {
+			#cooling-cells = <2>;
+		};
+
+		cpu1: cpu@1 {
+			#cooling-cells = <2>;
+		};
+
+		cpu2: cpu@2 {
+			#cooling-cells = <2>;
+		};
+
+		cpu3: cpu@3 {
+			#cooling-cells = <2>;
+		};
+	};
+
+	thermal-zones {
+		cpu-skin-thermal {
+			polling-delay-passive = <1000>; /* milliseconds */
+			polling-delay = <5000>; /* milliseconds */
+
+			thermal-sensors = <&tmp451 0>;
+
+			trips {
+				cpu_passive_trip: cpu-alert0 {
+					/* throttle at 70C until temperature drops to 69.8C */
+					temperature = <70000>;
+					hysteresis = <200>;
+					type = "passive";
+				};
+			};
+
+			cooling-maps {
+				map0 {
+					trip = <&cpu_passive_trip>;
+					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+	};
 };
 
 #include "cros-ec-keyboard.dtsi"
diff --git a/arch/arm/boot/dts/tegra124-peripherals-opp.dtsi b/arch/arm/boot/dts/tegra124-peripherals-opp.dtsi
index 781ac8601030..b262c1289da5 100644
--- a/arch/arm/boot/dts/tegra124-peripherals-opp.dtsi
+++ b/arch/arm/boot/dts/tegra124-peripherals-opp.dtsi
@@ -1,421 +1,421 @@
 // SPDX-License-Identifier: GPL-2.0
 
 / {
-	emc_icc_dvfs_opp_table: emc-dvfs-opp-table {
+	emc_icc_dvfs_opp_table: opp-table-emc {
 		compatible = "operating-points-v2";
 
-		opp@12750000,800 {
+		opp-12750000-800 {
 			opp-microvolt = <800000 800000 1150000>;
 			opp-hz = /bits/ 64 <12750000>;
 			opp-supported-hw = <0x0003>;
 		};
 
-		opp@12750000,950 {
+		opp-12750000-950 {
 			opp-microvolt = <950000 950000 1150000>;
 			opp-hz = /bits/ 64 <12750000>;
 			opp-supported-hw = <0x0008>;
 		};
 
-		opp@12750000,1050 {
+		opp-12750000-1050 {
 			opp-microvolt = <1050000 1050000 1150000>;
 			opp-hz = /bits/ 64 <12750000>;
 			opp-supported-hw = <0x0010>;
 		};
 
-		opp@12750000,1110 {
+		opp-12750000-1110 {
 			opp-microvolt = <1110000 1110000 1150000>;
 			opp-hz = /bits/ 64 <12750000>;
 			opp-supported-hw = <0x0004>;
 		};
 
-		opp@20400000,800 {
+		opp-20400000-800 {
 			opp-microvolt = <800000 800000 1150000>;
 			opp-hz = /bits/ 64 <20400000>;
 			opp-supported-hw = <0x0003>;
 		};
 
-		opp@20400000,950 {
+		opp-20400000-950 {
 			opp-microvolt = <950000 950000 1150000>;
 			opp-hz = /bits/ 64 <20400000>;
 			opp-supported-hw = <0x0008>;
 		};
 
-		opp@20400000,1050 {
+		opp-20400000-1050 {
 			opp-microvolt = <1050000 1050000 1150000>;
 			opp-hz = /bits/ 64 <20400000>;
 			opp-supported-hw = <0x0010>;
 		};
 
-		opp@20400000,1110 {
+		opp-20400000-1110 {
 			opp-microvolt = <1110000 1110000 1150000>;
 			opp-hz = /bits/ 64 <20400000>;
 			opp-supported-hw = <0x0004>;
 		};
 
-		opp@40800000,800 {
+		opp-40800000-800 {
 			opp-microvolt = <800000 800000 1150000>;
 			opp-hz = /bits/ 64 <40800000>;
 			opp-supported-hw = <0x0003>;
 		};
 
-		opp@40800000,950 {
+		opp-40800000-950 {
 			opp-microvolt = <950000 950000 1150000>;
 			opp-hz = /bits/ 64 <40800000>;
 			opp-supported-hw = <0x0008>;
 		};
 
-		opp@40800000,1050 {
+		opp-40800000-1050 {
 			opp-microvolt = <1050000 1050000 1150000>;
 			opp-hz = /bits/ 64 <40800000>;
 			opp-supported-hw = <0x0010>;
 		};
 
-		opp@40800000,1110 {
+		opp-40800000-1110 {
 			opp-microvolt = <1110000 1110000 1150000>;
 			opp-hz = /bits/ 64 <40800000>;
 			opp-supported-hw = <0x0004>;
 		};
 
-		opp@68000000,800 {
+		opp-68000000-800 {
 			opp-microvolt = <800000 800000 1150000>;
 			opp-hz = /bits/ 64 <68000000>;
 			opp-supported-hw = <0x0003>;
 		};
 
-		opp@68000000,950 {
+		opp-68000000-950 {
 			opp-microvolt = <950000 950000 1150000>;
 			opp-hz = /bits/ 64 <68000000>;
 			opp-supported-hw = <0x0008>;
 		};
 
-		opp@68000000,1050 {
+		opp-68000000-1050 {
 			opp-microvolt = <1050000 1050000 1150000>;
 			opp-hz = /bits/ 64 <68000000>;
 			opp-supported-hw = <0x0010>;
 		};
 
-		opp@68000000,1110 {
+		opp-68000000-1110 {
 			opp-microvolt = <1110000 1110000 1150000>;
 			opp-hz = /bits/ 64 <68000000>;
 			opp-supported-hw = <0x0004>;
 		};
 
-		opp@102000000,800 {
+		opp-102000000-800 {
 			opp-microvolt = <800000 800000 1150000>;
 			opp-hz = /bits/ 64 <102000000>;
 			opp-supported-hw = <0x0003>;
 		};
 
-		opp@102000000,950 {
+		opp-102000000-950 {
 			opp-microvolt = <950000 950000 1150000>;
 			opp-hz = /bits/ 64 <102000000>;
 			opp-supported-hw = <0x0008>;
 		};
 
-		opp@102000000,1050 {
+		opp-102000000-1050 {
 			opp-microvolt = <1050000 1050000 1150000>;
 			opp-hz = /bits/ 64 <102000000>;
 			opp-supported-hw = <0x0010>;
 		};
 
-		opp@102000000,1110 {
+		opp-102000000-1110 {
 			opp-microvolt = <1110000 1110000 1150000>;
 			opp-hz = /bits/ 64 <102000000>;
 			opp-supported-hw = <0x0004>;
 		};
 
-		opp@204000000,800 {
+		opp-204000000-800 {
 			opp-microvolt = <800000 800000 1150000>;
 			opp-hz = /bits/ 64 <204000000>;
 			opp-supported-hw = <0x0003>;
 			opp-suspend;
 		};
 
-		opp@204000000,950 {
+		opp-204000000-950 {
 			opp-microvolt = <950000 950000 1150000>;
 			opp-hz = /bits/ 64 <204000000>;
 			opp-supported-hw = <0x0008>;
 			opp-suspend;
 		};
 
-		opp@204000000,1050 {
+		opp-204000000-1050 {
 			opp-microvolt = <1050000 1050000 1150000>;
 			opp-hz = /bits/ 64 <204000000>;
 			opp-supported-hw = <0x0010>;
 			opp-suspend;
 		};
 
-		opp@204000000,1110 {
+		opp-204000000-1110 {
 			opp-microvolt = <1110000 1110000 1150000>;
 			opp-hz = /bits/ 64 <204000000>;
 			opp-supported-hw = <0x0004>;
 			opp-suspend;
 		};
 
-		opp@264000000,800 {
+		opp-264000000-800 {
 			opp-microvolt = <800000 800000 1150000>;
 			opp-hz = /bits/ 64 <264000000>;
 			opp-supported-hw = <0x0003>;
 		};
 
-		opp@264000000,950 {
+		opp-264000000-950 {
 			opp-microvolt = <950000 950000 1150000>;
 			opp-hz = /bits/ 64 <264000000>;
 			opp-supported-hw = <0x0008>;
 		};
 
-		opp@264000000,1050 {
+		opp-264000000-1050 {
 			opp-microvolt = <1050000 1050000 1150000>;
 			opp-hz = /bits/ 64 <264000000>;
 			opp-supported-hw = <0x0010>;
 		};
 
-		opp@264000000,1110 {
+		opp-264000000-1110 {
 			opp-microvolt = <1110000 1110000 1150000>;
 			opp-hz = /bits/ 64 <264000000>;
 			opp-supported-hw = <0x0004>;
 		};
 
-		opp@300000000,850 {
+		opp-300000000-850 {
 			opp-microvolt = <850000 850000 1150000>;
 			opp-hz = /bits/ 64 <300000000>;
 			opp-supported-hw = <0x0003>;
 		};
 
-		opp@300000000,950 {
+		opp-300000000-950 {
 			opp-microvolt = <950000 950000 1150000>;
 			opp-hz = /bits/ 64 <300000000>;
 			opp-supported-hw = <0x0008>;
 		};
 
-		opp@300000000,1050 {
+		opp-300000000-1050 {
 			opp-microvolt = <1050000 1050000 1150000>;
 			opp-hz = /bits/ 64 <300000000>;
 			opp-supported-hw = <0x0010>;
 		};
 
-		opp@300000000,1110 {
+		opp-300000000-1110 {
 			opp-microvolt = <1110000 1110000 1150000>;
 			opp-hz = /bits/ 64 <300000000>;
 			opp-supported-hw = <0x0004>;
 		};
 
-		opp@348000000,850 {
+		opp-348000000-850 {
 			opp-microvolt = <850000 850000 1150000>;
 			opp-hz = /bits/ 64 <348000000>;
 			opp-supported-hw = <0x0003>;
 		};
 
-		opp@348000000,950 {
+		opp-348000000-950 {
 			opp-microvolt = <950000 950000 1150000>;
 			opp-hz = /bits/ 64 <348000000>;
 			opp-supported-hw = <0x0008>;
 		};
 
-		opp@348000000,1050 {
+		opp-348000000-1050 {
 			opp-microvolt = <1050000 1050000 1150000>;
 			opp-hz = /bits/ 64 <348000000>;
 			opp-supported-hw = <0x0010>;
 		};
 
-		opp@348000000,1110 {
+		opp-348000000-1110 {
 			opp-microvolt = <1110000 1110000 1150000>;
 			opp-hz = /bits/ 64 <348000000>;
 			opp-supported-hw = <0x0004>;
 		};
 
-		opp@396000000,950 {
+		opp-396000000-950 {
 			opp-microvolt = <950000 950000 1150000>;
 			opp-hz = /bits/ 64 <396000000>;
 			opp-supported-hw = <0x0008>;
 		};
 
-		opp@396000000,1000 {
+		opp-396000000-1000 {
 			opp-microvolt = <1000000 1000000 1150000>;
 			opp-hz = /bits/ 64 <396000000>;
 			opp-supported-hw = <0x0003>;
 		};
 
-		opp@396000000,1050 {
+		opp-396000000-1050 {
 			opp-microvolt = <1050000 1050000 1150000>;
 			opp-hz = /bits/ 64 <396000000>;
 			opp-supported-hw = <0x0010>;
 		};
 
-		opp@396000000,1110 {
+		opp-396000000-1110 {
 			opp-microvolt = <1110000 1110000 1150000>;
 			opp-hz = /bits/ 64 <396000000>;
 			opp-supported-hw = <0x0004>;
 		};
 
-		opp@528000000,950 {
+		opp-528000000-950 {
 			opp-microvolt = <950000 950000 1150000>;
 			opp-hz = /bits/ 64 <528000000>;
 			opp-supported-hw = <0x0008>;
 		};
 
-		opp@528000000,1000 {
+		opp-528000000-1000 {
 			opp-microvolt = <1000000 1000000 1150000>;
 			opp-hz = /bits/ 64 <528000000>;
 			opp-supported-hw = <0x0003>;
 		};
 
-		opp@528000000,1050 {
+		opp-528000000-1050 {
 			opp-microvolt = <1050000 1050000 1150000>;
 			opp-hz = /bits/ 64 <528000000>;
 			opp-supported-hw = <0x0010>;
 		};
 
-		opp@528000000,1110 {
+		opp-528000000-1110 {
 			opp-microvolt = <1110000 1110000 1150000>;
 			opp-hz = /bits/ 64 <528000000>;
 			opp-supported-hw = <0x0004>;
 		};
 
-		opp@600000000,950 {
+		opp-600000000-950 {
 			opp-microvolt = <950000 950000 1150000>;
 			opp-hz = /bits/ 64 <600000000>;
 			opp-supported-hw = <0x0008>;
 		};
 
-		opp@600000000,1000 {
+		opp-600000000-1000 {
 			opp-microvolt = <1000000 1000000 1150000>;
 			opp-hz = /bits/ 64 <600000000>;
 			opp-supported-hw = <0x0003>;
 		};
 
-		opp@600000000,1050 {
+		opp-600000000-1050 {
 			opp-microvolt = <1050000 1050000 1150000>;
 			opp-hz = /bits/ 64 <600000000>;
 			opp-supported-hw = <0x0010>;
 		};
 
-		opp@600000000,1110 {
+		opp-600000000-1110 {
 			opp-microvolt = <1110000 1110000 1150000>;
 			opp-hz = /bits/ 64 <600000000>;
 			opp-supported-hw = <0x0004>;
 		};
 
-		opp@792000000,1000 {
+		opp-792000000-1000 {
 			opp-microvolt = <1000000 1000000 1150000>;
 			opp-hz = /bits/ 64 <792000000>;
 			opp-supported-hw = <0x000B>;
 		};
 
-		opp@792000000,1050 {
+		opp-792000000-1050 {
 			opp-microvolt = <1050000 1050000 1150000>;
 			opp-hz = /bits/ 64 <792000000>;
 			opp-supported-hw = <0x0010>;
 		};
 
-		opp@792000000,1110 {
+		opp-792000000-1110 {
 			opp-microvolt = <1110000 1110000 1150000>;
 			opp-hz = /bits/ 64 <792000000>;
 			opp-supported-hw = <0x0004>;
 		};
 
-		opp@924000000,1100 {
+		opp-924000000-1100 {
 			opp-microvolt = <1100000 1100000 1150000>;
 			opp-hz = /bits/ 64 <924000000>;
 			opp-supported-hw = <0x0013>;
 		};
 
-		opp@1200000000,1100 {
+		opp-1200000000-1100 {
 			opp-microvolt = <1100000 1100000 1150000>;
 			opp-hz = /bits/ 64 <1200000000>;
 			opp-supported-hw = <0x0003>;
 		};
 	};
 
-	emc_bw_dfs_opp_table: emc-bandwidth-opp-table {
+	emc_bw_dfs_opp_table: opp-table-actmon {
 		compatible = "operating-points-v2";
 
-		opp@12750000 {
+		opp-12750000 {
 			opp-hz = /bits/ 64 <12750000>;
 			opp-supported-hw = <0x001F>;
 			opp-peak-kBps = <204000>;
 		};
 
-		opp@20400000 {
+		opp-20400000 {
 			opp-hz = /bits/ 64 <20400000>;
 			opp-supported-hw = <0x001F>;
 			opp-peak-kBps = <326400>;
 		};
 
-		opp@40800000 {
+		opp-40800000 {
 			opp-hz = /bits/ 64 <40800000>;
 			opp-supported-hw = <0x001F>;
 			opp-peak-kBps = <652800>;
 		};
 
-		opp@68000000 {
+		opp-68000000 {
 			opp-hz = /bits/ 64 <68000000>;
 			opp-supported-hw = <0x001F>;
 			opp-peak-kBps = <1088000>;
 		};
 
-		opp@102000000 {
+		opp-102000000 {
 			opp-hz = /bits/ 64 <102000000>;
 			opp-supported-hw = <0x001F>;
 			opp-peak-kBps = <1632000>;
 		};
 
-		opp@204000000 {
+		opp-204000000 {
 			opp-hz = /bits/ 64 <204000000>;
 			opp-supported-hw = <0x001F>;
 			opp-peak-kBps = <3264000>;
 			opp-suspend;
 		};
 
-		opp@264000000 {
+		opp-264000000 {
 			opp-hz = /bits/ 64 <264000000>;
 			opp-supported-hw = <0x001F>;
 			opp-peak-kBps = <4224000>;
 		};
 
-		opp@300000000 {
+		opp-300000000 {
 			opp-hz = /bits/ 64 <300000000>;
 			opp-supported-hw = <0x001F>;
 			opp-peak-kBps = <4800000>;
 		};
 
-		opp@348000000 {
+		opp-348000000 {
 			opp-hz = /bits/ 64 <348000000>;
 			opp-supported-hw = <0x001F>;
 			opp-peak-kBps = <5568000>;
 		};
 
-		opp@396000000 {
+		opp-396000000 {
 			opp-hz = /bits/ 64 <396000000>;
 			opp-supported-hw = <0x001F>;
 			opp-peak-kBps = <6336000>;
 		};
 
-		opp@528000000 {
+		opp-528000000 {
 			opp-hz = /bits/ 64 <528000000>;
 			opp-supported-hw = <0x001F>;
 			opp-peak-kBps = <8448000>;
 		};
 
-		opp@600000000 {
+		opp-600000000 {
 			opp-hz = /bits/ 64 <600000000>;
 			opp-supported-hw = <0x001F>;
 			opp-peak-kBps = <9600000>;
 		};
 
-		opp@792000000 {
+		opp-792000000 {
 			opp-hz = /bits/ 64 <792000000>;
 			opp-supported-hw = <0x001F>;
 			opp-peak-kBps = <12672000>;
 		};
 
-		opp@924000000 {
+		opp-924000000 {
 			opp-hz = /bits/ 64 <924000000>;
 			opp-supported-hw = <0x0013>;
 			opp-peak-kBps = <14784000>;
 		};
 
-		opp@1200000000 {
+		opp-1200000000 {
 			opp-hz = /bits/ 64 <1200000000>;
 			opp-supported-hw = <0x0003>;
 			opp-peak-kBps = <19200000>;
diff --git a/arch/arm/boot/dts/tegra124-venice2.dts b/arch/arm/boot/dts/tegra124-venice2.dts
index e6b54ac1ebd1..8f40fcfc11b0 100644
--- a/arch/arm/boot/dts/tegra124-venice2.dts
+++ b/arch/arm/boot/dts/tegra124-venice2.dts
@@ -48,10 +48,17 @@
 		dpaux@545c0000 {
 			vdd-supply = <&vdd_3v3_panel>;
 			status = "okay";
+
+			aux-bus {
+				panel: panel {
+					compatible = "lg,lp129qe";
+					backlight = <&backlight>;
+				};
+			};
 		};
 	};
 
-	gpu@0,57000000 {
+	gpu@57000000 {
 		/*
 		 * Node left disabled on purpose - the bootloader will enable
 		 * it after having set the VPR up
@@ -881,7 +888,8 @@
 	spi@7000da00 {
 		status = "okay";
 		spi-max-frequency = <25000000>;
-		spi-flash@0 {
+
+		flash@0 {
 			compatible = "winbond,w25q32dw", "jedec,spi-nor";
 			reg = <0>;
 			spi-max-frequency = <20000000>;
@@ -972,7 +980,7 @@
 			usb2-0 {
 				status = "okay";
 				mode = "otg";
-
+				usb-role-switch;
 				vbus-supply = <&vdd_usb1_vbus>;
 			};
 
@@ -1061,7 +1069,7 @@
 		default-brightness-level = <6>;
 	};
 
-	clk32k_in: clock@0 {
+	clk32k_in: clock-32k {
 		compatible = "fixed-clock";
 		clock-frequency = <32768>;
 		#clock-cells = <0>;
@@ -1070,7 +1078,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		power {
+		key-power {
 			label = "Power";
 			gpios = <&gpio TEGRA_GPIO(Q, 0) GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
@@ -1079,14 +1087,7 @@
 		};
 	};
 
-	panel: panel {
-		compatible = "lg,lp129qe";
-		power-supply = <&vdd_3v3_panel>;
-		backlight = <&backlight>;
-		ddc-i2c-bus = <&dpaux>;
-	};
-
-	vdd_mux: regulator@0 {
+	vdd_mux: regulator-mux {
 		compatible = "regulator-fixed";
 		regulator-name = "+VDD_MUX";
 		regulator-min-microvolt = <12000000>;
@@ -1095,7 +1096,7 @@
 		regulator-boot-on;
 	};
 
-	vdd_5v0_sys: regulator@1 {
+	vdd_5v0_sys: regulator-5v0sys {
 		compatible = "regulator-fixed";
 		regulator-name = "+5V_SYS";
 		regulator-min-microvolt = <5000000>;
@@ -1105,7 +1106,7 @@
 		vin-supply = <&vdd_mux>;
 	};
 
-	vdd_3v3_sys: regulator@2 {
+	vdd_3v3_sys: regulator-3v3sys {
 		compatible = "regulator-fixed";
 		regulator-name = "+3.3V_SYS";
 		regulator-min-microvolt = <3300000>;
@@ -1115,7 +1116,7 @@
 		vin-supply = <&vdd_mux>;
 	};
 
-	vdd_3v3_run: regulator@3 {
+	vdd_3v3_run: regulator-3v3run {
 		compatible = "regulator-fixed";
 		regulator-name = "+3.3V_RUN";
 		regulator-min-microvolt = <3300000>;
@@ -1127,7 +1128,7 @@
 		vin-supply = <&vdd_3v3_sys>;
 	};
 
-	vdd_3v3_hdmi: regulator@4 {
+	vdd_3v3_hdmi: regulator-hdmi {
 		compatible = "regulator-fixed";
 		regulator-name = "+3.3V_AVDD_HDMI_AP_GATED";
 		regulator-min-microvolt = <3300000>;
@@ -1135,7 +1136,7 @@
 		vin-supply = <&vdd_3v3_run>;
 	};
 
-	vdd_led: regulator@5 {
+	vdd_led: regulator-led {
 		compatible = "regulator-fixed";
 		regulator-name = "+VDD_LED";
 		regulator-min-microvolt = <3300000>;
@@ -1145,7 +1146,7 @@
 		vin-supply = <&vdd_mux>;
 	};
 
-	vdd_5v0_ts: regulator@6 {
+	vdd_5v0_ts: regulator-ts {
 		compatible = "regulator-fixed";
 		regulator-name = "+5V_VDD_TS_SW";
 		regulator-min-microvolt = <5000000>;
@@ -1156,7 +1157,7 @@
 		vin-supply = <&vdd_5v0_sys>;
 	};
 
-	vdd_usb1_vbus: regulator@7 {
+	vdd_usb1_vbus: regulator-usb1 {
 		compatible = "regulator-fixed";
 		regulator-name = "+5V_USB_HS";
 		regulator-min-microvolt = <5000000>;
@@ -1167,7 +1168,7 @@
 		vin-supply = <&vdd_5v0_sys>;
 	};
 
-	vdd_usb3_vbus: regulator@8 {
+	vdd_usb3_vbus: regulator-usb3 {
 		compatible = "regulator-fixed";
 		regulator-name = "+5V_USB_SS";
 		regulator-min-microvolt = <5000000>;
@@ -1178,7 +1179,7 @@
 		vin-supply = <&vdd_5v0_sys>;
 	};
 
-	vdd_3v3_panel: regulator@9 {
+	vdd_3v3_panel: regulator-panel {
 		compatible = "regulator-fixed";
 		regulator-name = "+3.3V_PANEL";
 		regulator-min-microvolt = <3300000>;
@@ -1188,7 +1189,7 @@
 		vin-supply = <&vdd_3v3_run>;
 	};
 
-	vdd_3v3_lp0: regulator@10 {
+	vdd_3v3_lp0: regulator-lp0 {
 		compatible = "regulator-fixed";
 		regulator-name = "+3.3V_LP0";
 		regulator-min-microvolt = <3300000>;
@@ -1203,7 +1204,7 @@
 		vin-supply = <&vdd_3v3_sys>;
 	};
 
-	vdd_hdmi_pll: regulator@11 {
+	vdd_hdmi_pll: regulator-hdmipll {
 		compatible = "regulator-fixed";
 		regulator-name = "+1.05V_RUN_AVDD_HDMI_PLL";
 		regulator-min-microvolt = <1050000>;
@@ -1212,7 +1213,7 @@
 		vin-supply = <&vdd_1v05_run>;
 	};
 
-	vdd_5v0_hdmi: regulator@12 {
+	vdd_5v0_hdmi: regulator-hdmicon {
 		compatible = "regulator-fixed";
 		regulator-name = "+5V_HDMI_CON";
 		regulator-min-microvolt = <5000000>;
diff --git a/arch/arm/boot/dts/tegra124.dtsi b/arch/arm/boot/dts/tegra124.dtsi
index 63a64171b422..a9ab548781e1 100644
--- a/arch/arm/boot/dts/tegra124.dtsi
+++ b/arch/arm/boot/dts/tegra124.dtsi
@@ -94,8 +94,8 @@
 		interrupt-names = "syncpt", "host1x";
 		clocks = <&tegra_car TEGRA124_CLK_HOST1X>;
 		clock-names = "host1x";
-		resets = <&tegra_car 28>;
-		reset-names = "host1x";
+		resets = <&tegra_car 28>, <&mc TEGRA124_MC_RESET_HC>;
+		reset-names = "host1x", "mc";
 		iommus = <&mc TEGRA_SWGROUP_HC>;
 
 		#address-cells = <2>;
@@ -223,12 +223,7 @@
 		interrupt-parent = <&gic>;
 	};
 
-	/*
-	 * Please keep the following 0, notation in place as a former mainline
-	 * U-Boot version was looking for that particular notation in order to
-	 * perform required fix-ups on that GPU node.
-	 */
-	gpu@0,57000000 {
+	gpu@57000000 {
 		compatible = "nvidia,gk20a";
 		reg = <0x0 0x57000000 0x0 0x01000000>,
 		      <0x0 0x58000000 0x0 0x01000000>;
@@ -259,7 +254,7 @@
 	};
 
 	timer@60005000 {
-		compatible = "nvidia,tegra124-timer", "nvidia,tegra30-timer", "nvidia,tegra20-timer";
+		compatible = "nvidia,tegra124-timer", "nvidia,tegra30-timer";
 		reg = <0x0 0x60005000 0x0 0x400>;
 		interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
 			     <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>,
@@ -313,9 +308,7 @@
 		gpio-controller;
 		#interrupt-cells = <2>;
 		interrupt-controller;
-		/*
 		gpio-ranges = <&pinmux 0 0 251>;
-		*/
 	};
 
 	apbdma: dma@60020000 {
@@ -443,7 +436,7 @@
 	};
 
 	i2c@7000c000 {
-		compatible = "nvidia,tegra124-i2c", "nvidia,tegra114-i2c";
+		compatible = "nvidia,tegra124-i2c";
 		reg = <0x0 0x7000c000 0x0 0x100>;
 		interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
 		#address-cells = <1>;
@@ -458,7 +451,7 @@
 	};
 
 	i2c@7000c400 {
-		compatible = "nvidia,tegra124-i2c", "nvidia,tegra114-i2c";
+		compatible = "nvidia,tegra124-i2c";
 		reg = <0x0 0x7000c400 0x0 0x100>;
 		interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
 		#address-cells = <1>;
@@ -473,7 +466,7 @@
 	};
 
 	i2c@7000c500 {
-		compatible = "nvidia,tegra124-i2c", "nvidia,tegra114-i2c";
+		compatible = "nvidia,tegra124-i2c";
 		reg = <0x0 0x7000c500 0x0 0x100>;
 		interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>;
 		#address-cells = <1>;
@@ -488,7 +481,7 @@
 	};
 
 	i2c@7000c700 {
-		compatible = "nvidia,tegra124-i2c", "nvidia,tegra114-i2c";
+		compatible = "nvidia,tegra124-i2c";
 		reg = <0x0 0x7000c700 0x0 0x100>;
 		interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
 		#address-cells = <1>;
@@ -503,7 +496,7 @@
 	};
 
 	i2c@7000d000 {
-		compatible = "nvidia,tegra124-i2c", "nvidia,tegra114-i2c";
+		compatible = "nvidia,tegra124-i2c";
 		reg = <0x0 0x7000d000 0x0 0x100>;
 		interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>;
 		#address-cells = <1>;
@@ -518,7 +511,7 @@
 	};
 
 	i2c@7000d100 {
-		compatible = "nvidia,tegra124-i2c", "nvidia,tegra114-i2c";
+		compatible = "nvidia,tegra124-i2c";
 		reg = <0x0 0x7000d100 0x0 0x100>;
 		interrupts = <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>;
 		#address-cells = <1>;
@@ -677,10 +670,8 @@
 		      <0x0 0x70020000 0x0 0x7000>; /* SATA */
 		interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&tegra_car TEGRA124_CLK_SATA>,
-			 <&tegra_car TEGRA124_CLK_SATA_OOB>,
-			 <&tegra_car TEGRA124_CLK_CML1>,
-			 <&tegra_car TEGRA124_CLK_PLL_E>;
-		clock-names = "sata", "sata-oob", "cml1", "pll_e";
+			 <&tegra_car TEGRA124_CLK_SATA_OOB>;
+		clock-names = "sata", "sata-oob";
 		resets = <&tegra_car 124>,
 			 <&tegra_car 129>,
 			 <&tegra_car 123>;
@@ -717,8 +708,8 @@
 			 <&tegra_car TEGRA124_CLK_XUSB_HOST_SRC>,
 			 <&tegra_car TEGRA124_CLK_XUSB_FALCON_SRC>,
 			 <&tegra_car TEGRA124_CLK_XUSB_SS>,
-			 <&tegra_car TEGRA124_CLK_XUSB_SS_SRC>,
 			 <&tegra_car TEGRA124_CLK_XUSB_SS_DIV2>,
+			 <&tegra_car TEGRA124_CLK_XUSB_SS_SRC>,
 			 <&tegra_car TEGRA124_CLK_XUSB_HS_SRC>,
 			 <&tegra_car TEGRA124_CLK_XUSB_FS_SRC>,
 			 <&tegra_car TEGRA124_CLK_PLL_U_480M>,
@@ -726,7 +717,7 @@
 			 <&tegra_car TEGRA124_CLK_PLL_E>;
 		clock-names = "xusb_host", "xusb_host_src",
 			      "xusb_falcon_src", "xusb_ss",
-			      "xusb_ss_src", "xusb_ss_div2",
+			      "xusb_ss_div2", "xusb_ss_src",
 			      "xusb_hs_src", "xusb_fs_src",
 			      "pll_u_480m", "clk_m", "pll_e";
 		resets = <&tegra_car 89>, <&tegra_car 156>,
@@ -1247,7 +1238,7 @@
 	};
 
 	thermal-zones {
-		cpu {
+		cpu-thermal {
 			polling-delay-passive = <1000>;
 			polling-delay = <1000>;
 
@@ -1275,7 +1266,7 @@
 			};
 		};
 
-		mem {
+		mem-thermal {
 			polling-delay-passive = <1000>;
 			polling-delay = <1000>;
 
@@ -1303,7 +1294,7 @@
 			};
 		};
 
-		gpu {
+		gpu-thermal {
 			polling-delay-passive = <1000>;
 			polling-delay = <1000>;
 
@@ -1331,7 +1322,7 @@
 			};
 		};
 
-		pllx {
+		pllx-thermal {
 			polling-delay-passive = <1000>;
 			polling-delay = <1000>;
 
diff --git a/arch/arm/boot/dts/tegra20-acer-a500-picasso.dts b/arch/arm/boot/dts/tegra20-acer-a500-picasso.dts
index 23d3f8daab23..dac6d02a1b15 100644
--- a/arch/arm/boot/dts/tegra20-acer-a500-picasso.dts
+++ b/arch/arm/boot/dts/tegra20-acer-a500-picasso.dts
@@ -376,17 +376,27 @@
 		};
 	};
 
+	tegra_spdif: spdif@70002400 {
+		status = "okay";
+
+		nvidia,fixed-parent-rate;
+	};
+
 	tegra_i2s1: i2s@70002800 {
 		status = "okay";
+
+		nvidia,fixed-parent-rate;
 	};
 
 	uartb: serial@70006040 {
 		compatible = "nvidia,tegra20-hsuart";
+		/delete-property/ reg-shift;
 		/* GPS BCM4751 */
 	};
 
 	uartc: serial@70006200 {
 		compatible = "nvidia,tegra20-hsuart";
+		/delete-property/ reg-shift;
 		status = "okay";
 
 		/* Azurewave AW-NH665 BCM4329B1 */
@@ -407,7 +417,7 @@
 			vddio-supply = <&vdd_1v8_sys>;
 
 			device-wakeup-gpios = <&gpio TEGRA_GPIO(U, 1) GPIO_ACTIVE_HIGH>;
-			shutdown-gpios =      <&gpio TEGRA_GPIO(U, 0) GPIO_ACTIVE_HIGH>;
+			shutdown-gpios = <&gpio TEGRA_GPIO(U, 0) GPIO_ACTIVE_HIGH>;
 		};
 	};
 
@@ -716,6 +726,7 @@
 		nvidia,core-pwr-good-time = <3845 3845>;
 		nvidia,core-pwr-off-time = <458>;
 		nvidia,sys-clock-req-active-high;
+		core-supply = <&vdd_core>;
 	};
 
 	usb@c5000000 {
@@ -827,7 +838,7 @@
 	};
 
 	/* PMIC has a built-in 32KHz oscillator which is used by PMC */
-	clk32k_in: clock@0 {
+	clk32k_in: clock-32k-in {
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
 		clock-frequency = <32768>;
@@ -839,7 +850,7 @@
 	 * oscillator is used as a reference clock-source by the
 	 * Azurewave WiFi/BT module.
 	 */
-	rtc_32k_wifi: clock@1 {
+	rtc_32k_wifi: clock-32k-wifi {
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
 		clock-frequency = <32768>;
@@ -894,7 +905,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		power {
+		key-power {
 			label = "Power";
 			gpios = <&gpio TEGRA_GPIO(I, 3) GPIO_ACTIVE_HIGH>;
 			linux,code = <KEY_POWER>;
@@ -903,7 +914,7 @@
 			wakeup-source;
 		};
 
-		rotation-lock {
+		key-rotation-lock {
 			label = "Rotate-lock";
 			gpios = <&gpio TEGRA_GPIO(Q, 2) GPIO_ACTIVE_HIGH>;
 			linux,code = <SW_ROTATE_LOCK>;
@@ -911,7 +922,7 @@
 			debounce-interval = <10>;
 		};
 
-		volume-up {
+		key-volume-up {
 			label = "Volume Up";
 			gpios = <&gpio TEGRA_GPIO(Q, 4) GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_VOLUMEUP>;
@@ -920,7 +931,7 @@
 			wakeup-source;
 		};
 
-		volume-down {
+		key-volume-down {
 			label = "Volume Down";
 			gpios = <&gpio TEGRA_GPIO(Q, 5) GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_VOLUMEDOWN>;
@@ -964,7 +975,7 @@
 		};
 	};
 
-	vdd_5v0_sys: regulator@0 {
+	vdd_5v0_sys: regulator-5v0 {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd_5v0";
 		regulator-min-microvolt = <5000000>;
@@ -972,7 +983,7 @@
 		regulator-always-on;
 	};
 
-	vdd_3v3_sys: regulator@1 {
+	vdd_3v3_sys: regulator-3v3 {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd_3v3_vs";
 		regulator-min-microvolt = <3300000>;
@@ -981,7 +992,7 @@
 		vin-supply = <&vdd_5v0_sys>;
 	};
 
-	vdd_1v8_sys: regulator@2 {
+	vdd_1v8_sys: regulator-1v8 {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd_1v8_vs";
 		regulator-min-microvolt = <1800000>;
@@ -990,7 +1001,7 @@
 		vin-supply = <&vdd_5v0_sys>;
 	};
 
-	vdd_pnl: regulator@3 {
+	vdd_pnl: regulator-panel {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd_panel";
 		regulator-min-microvolt = <3300000>;
@@ -1506,6 +1517,6 @@
 };
 
 &emc_icc_dvfs_opp_table {
-	/delete-node/ opp@666000000;
-	/delete-node/ opp@760000000;
+	/delete-node/ opp-666000000;
+	/delete-node/ opp-760000000;
 };
diff --git a/arch/arm/boot/dts/tegra20-asus-tf101.dts b/arch/arm/boot/dts/tegra20-asus-tf101.dts
new file mode 100644
index 000000000000..bf797a1f27ea
--- /dev/null
+++ b/arch/arm/boot/dts/tegra20-asus-tf101.dts
@@ -0,0 +1,1290 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include <dt-bindings/input/atmel-maxtouch.h>
+#include <dt-bindings/input/gpio-keys.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/thermal/thermal.h>
+
+#include "tegra20.dtsi"
+#include "tegra20-cpu-opp.dtsi"
+#include "tegra20-cpu-opp-microvolt.dtsi"
+
+/ {
+	model = "ASUS EeePad Transformer TF101";
+	compatible = "asus,tf101", "nvidia,tegra20";
+	chassis-type = "convertible";
+
+	aliases {
+		mmc0 = &sdmmc4; /* eMMC */
+		mmc1 = &sdmmc3; /* MicroSD */
+		mmc2 = &sdmmc1; /* WiFi */
+
+		rtc0 = &pmic;
+		rtc1 = "/rtc@7000e000";
+
+		serial0 = &uartd;
+		serial1 = &uartc; /* Bluetooth */
+		serial2 = &uartb; /* GPS */
+	};
+
+	/*
+	 * The decompressor and also some bootloaders rely on a
+	 * pre-existing /chosen node to be available to insert the
+	 * command line and merge other ATAGS info.
+	 */
+	chosen {};
+
+	memory@0 {
+		reg = <0x00000000 0x40000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		ramoops@2ffe0000 {
+			compatible = "ramoops";
+			reg = <0x2ffe0000 0x10000>;	/* 64kB */
+			console-size = <0x8000>;	/* 32kB */
+			record-size = <0x400>;		/*  1kB */
+			ecc-size = <16>;
+		};
+
+		linux,cma@30000000 {
+			compatible = "shared-dma-pool";
+			alloc-ranges = <0x30000000 0x10000000>;
+			size = <0x10000000>; /* 256MiB */
+			linux,cma-default;
+			reusable;
+		};
+	};
+
+	host1x@50000000 {
+		dc@54200000 {
+			rgb {
+				status = "okay";
+
+				port@0 {
+					lcd_output: endpoint {
+						remote-endpoint = <&lvds_encoder_input>;
+						bus-width = <18>;
+					};
+				};
+			};
+		};
+
+		hdmi@54280000 {
+			status = "okay";
+
+			vdd-supply = <&hdmi_vdd_reg>;
+			pll-supply = <&hdmi_pll_reg>;
+			hdmi-supply = <&vdd_hdmi_en>;
+
+			nvidia,ddc-i2c-bus = <&hdmi_ddc>;
+			nvidia,hpd-gpio = <&gpio TEGRA_GPIO(N, 7)
+				GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	gpio@6000d000 {
+		charging-enable-hog {
+			gpio-hog;
+			gpios = <TEGRA_GPIO(R, 6) GPIO_ACTIVE_HIGH>;
+			output-low;
+		};
+	};
+
+	pinmux@70000014 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&state_default>;
+
+		state_default: pinmux {
+			ata {
+				nvidia,pins = "ata";
+				nvidia,function = "ide";
+			};
+
+			atb {
+				nvidia,pins = "atb", "gma", "gme";
+				nvidia,function = "sdio4";
+			};
+
+			atc {
+				nvidia,pins = "atc";
+				nvidia,function = "nand";
+			};
+
+			atd {
+				nvidia,pins = "atd", "ate", "gmb", "spia",
+					"spib", "spic";
+				nvidia,function = "gmi";
+			};
+
+			cdev1 {
+				nvidia,pins = "cdev1";
+				nvidia,function = "plla_out";
+			};
+
+			cdev2 {
+				nvidia,pins = "cdev2";
+				nvidia,function = "pllp_out4";
+			};
+
+			crtp {
+				nvidia,pins = "crtp";
+				nvidia,function = "crt";
+			};
+
+			lm1 {
+				nvidia,pins = "lm1";
+				nvidia,function = "rsvd3";
+			};
+
+			csus {
+				nvidia,pins = "csus";
+				nvidia,function = "vi_sensor_clk";
+			};
+
+			dap1 {
+				nvidia,pins = "dap1";
+				nvidia,function = "dap1";
+			};
+
+			dap2 {
+				nvidia,pins = "dap2";
+				nvidia,function = "dap2";
+			};
+
+			dap3 {
+				nvidia,pins = "dap3";
+				nvidia,function = "dap3";
+			};
+
+			dap4 {
+				nvidia,pins = "dap4";
+				nvidia,function = "dap4";
+			};
+
+			dta {
+				nvidia,pins = "dta", "dtb", "dtc", "dtd", "dte";
+				nvidia,function = "vi";
+			};
+
+			dtf {
+				nvidia,pins = "dtf";
+				nvidia,function = "i2c3";
+			};
+
+			gmc {
+				nvidia,pins = "gmc";
+				nvidia,function = "uartd";
+			};
+
+			gmd {
+				nvidia,pins = "gmd";
+				nvidia,function = "sflash";
+			};
+
+			gpu {
+				nvidia,pins = "gpu";
+				nvidia,function = "pwm";
+			};
+
+			gpu7 {
+				nvidia,pins = "gpu7";
+				nvidia,function = "rtck";
+			};
+
+			gpv {
+				nvidia,pins = "gpv", "slxa";
+				nvidia,function = "pcie";
+			};
+
+			hdint {
+				nvidia,pins = "hdint";
+				nvidia,function = "hdmi";
+			};
+
+			i2cp {
+				nvidia,pins = "i2cp";
+				nvidia,function = "i2cp";
+			};
+
+			irrx {
+				nvidia,pins = "irrx", "irtx";
+				nvidia,function = "uartb";
+			};
+
+			kbca {
+				nvidia,pins = "kbca", "kbcb", "kbcc", "kbcd",
+					"kbce", "kbcf";
+				nvidia,function = "kbc";
+			};
+
+			lcsn {
+				nvidia,pins = "lcsn", "ldc", "lm0", "lpw1",
+					"lsdi", "lvp0";
+				nvidia,function = "rsvd4";
+			};
+
+			ld0 {
+				nvidia,pins = "ld0", "ld1", "ld2", "ld3", "ld4",
+					"ld5", "ld6", "ld7", "ld8", "ld9",
+					"ld10", "ld11", "ld12", "ld13", "ld14",
+					"ld15", "ld16", "ld17", "ldi", "lhp0",
+					"lhp1", "lhp2", "lhs", "lpp", "lpw0",
+					"lpw2", "lsc0", "lsc1", "lsck", "lsda",
+					"lspi", "lvp1", "lvs";
+				nvidia,function = "displaya";
+			};
+
+			owc {
+				nvidia,pins = "owc", "spdi", "spdo", "uac";
+				nvidia,function = "rsvd2";
+			};
+
+			pmc {
+				nvidia,pins = "pmc";
+				nvidia,function = "pwr_on";
+			};
+
+			rm {
+				nvidia,pins = "rm";
+				nvidia,function = "i2c1";
+			};
+
+			sdb {
+				nvidia,pins = "sdb", "sdc", "sdd", "slxc", "slxk";
+				nvidia,function = "sdio3";
+			};
+
+			sdio1 {
+				nvidia,pins = "sdio1";
+				nvidia,function = "sdio1";
+			};
+
+			slxd {
+				nvidia,pins = "slxd";
+				nvidia,function = "spdif";
+			};
+
+			spid {
+				nvidia,pins = "spid", "spie", "spif";
+				nvidia,function = "spi1";
+			};
+
+			spig {
+				nvidia,pins = "spig", "spih";
+				nvidia,function = "spi2_alt";
+			};
+
+			uaa {
+				nvidia,pins = "uaa", "uab", "uda";
+				nvidia,function = "ulpi";
+			};
+
+			uad {
+				nvidia,pins = "uad";
+				nvidia,function = "irda";
+			};
+
+			uca {
+				nvidia,pins = "uca", "ucb";
+				nvidia,function = "uartc";
+			};
+
+			conf_ata {
+				nvidia,pins = "ata", "atb", "atc", "atd",
+					"cdev1", "cdev2", "dap1", "dap4",
+					"dte", "ddc", "dtf", "gma", "gmc",
+					"gme", "gpu", "gpu7", "gpv", "i2cp",
+					"irrx", "irtx", "pta", "rm", "sdc",
+					"sdd", "slxc", "slxd", "slxk", "spdi",
+					"spdo", "uac", "uad",
+					"uda", "csus";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+			};
+
+			conf_ate {
+				nvidia,pins = "ate", "dap2", "dap3", "gmb", "gmd",
+					"owc", "spia", "spib", "spic",
+					"spid", "spie", "spig", "slxa";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+			};
+
+			conf_ck32 {
+				nvidia,pins = "ck32", "ddrc", "pmca", "pmcb",
+					"pmcc", "pmcd", "pmce", "xm2c", "xm2d";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+			};
+
+			conf_crtp {
+				nvidia,pins = "crtp", "spih";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+			};
+
+			conf_dta {
+				nvidia,pins = "dta", "dtb", "dtc", "dtd";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+			};
+
+			conf_spif {
+				nvidia,pins = "spif";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+			};
+
+			conf_hdint {
+				nvidia,pins = "hdint", "lcsn", "ldc", "lm1",
+					"lpw1", "lsck", "lsda", "lsdi", "lvp0";
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+			};
+
+			conf_kbca {
+				nvidia,pins = "kbca", "kbcb", "kbcc", "kbcd",
+					"kbce", "kbcf", "sdio1", "uaa", "uab",
+					"uca", "ucb";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+			};
+
+			conf_lc {
+				nvidia,pins = "lc", "ls";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+			};
+
+			conf_ld0 {
+				nvidia,pins = "ld0", "ld1", "ld2", "ld3", "ld4",
+					"ld5", "ld6", "ld7", "ld8", "ld9",
+					"ld10", "ld11", "ld12", "ld13", "ld14",
+					"ld15", "ld16", "ld17", "ldi", "lhp0",
+					"lhp1", "lhp2", "lhs", "lm0", "lpp",
+					"lpw0", "lpw2", "lsc0", "lsc1", "lspi",
+					"lvp1", "lvs", "pmc", "sdb";
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+			};
+
+			conf_ld17_0 {
+				nvidia,pins = "ld17_0", "ld19_18", "ld21_20",
+					"ld23_22";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+			};
+
+			drive_sdio1 {
+				nvidia,pins = "drive_sdio1", "drive_ddc", "drive_vi1";
+				nvidia,high-speed-mode = <TEGRA_PIN_DISABLE>;
+				nvidia,schmitt = <TEGRA_PIN_ENABLE>;
+				nvidia,low-power-mode = <TEGRA_PIN_LP_DRIVE_DIV_1>;
+				nvidia,pull-down-strength = <31>;
+				nvidia,pull-up-strength = <31>;
+				nvidia,slew-rate-rising = <TEGRA_PIN_SLEW_RATE_SLOWEST>;
+				nvidia,slew-rate-falling = <TEGRA_PIN_SLEW_RATE_SLOWEST>;
+			};
+
+			drive_csus {
+				nvidia,pins = "drive_csus";
+				nvidia,high-speed-mode = <TEGRA_PIN_DISABLE>;
+				nvidia,schmitt = <TEGRA_PIN_DISABLE>;
+				nvidia,low-power-mode = <TEGRA_PIN_LP_DRIVE_DIV_1>;
+				nvidia,pull-down-strength = <31>;
+				nvidia,pull-up-strength = <31>;
+				nvidia,slew-rate-rising = <TEGRA_PIN_SLEW_RATE_SLOWEST>;
+				nvidia,slew-rate-falling = <TEGRA_PIN_SLEW_RATE_SLOWEST>;
+			};
+		};
+
+		state_i2cmux_ddc: pinmux_i2cmux_ddc {
+			ddc {
+				nvidia,pins = "ddc";
+				nvidia,function = "i2c2";
+			};
+
+			pta {
+				nvidia,pins = "pta";
+				nvidia,function = "rsvd4";
+			};
+		};
+
+		state_i2cmux_pta: pinmux_i2cmux_pta {
+			ddc {
+				nvidia,pins = "ddc";
+				nvidia,function = "rsvd4";
+			};
+
+			pta {
+				nvidia,pins = "pta";
+				nvidia,function = "i2c2";
+			};
+		};
+
+		state_i2cmux_idle: pinmux_i2cmux_idle {
+			ddc {
+				nvidia,pins = "ddc";
+				nvidia,function = "rsvd4";
+			};
+
+			pta {
+				nvidia,pins = "pta";
+				nvidia,function = "rsvd4";
+			};
+		};
+	};
+
+	spdif@70002400 {
+		status = "okay";
+
+		nvidia,fixed-parent-rate;
+	};
+
+	i2s@70002800 {
+		status = "okay";
+
+		nvidia,fixed-parent-rate;
+	};
+
+	serial@70006040 {
+		compatible = "nvidia,tegra20-hsuart";
+		/delete-property/ reg-shift;
+		/* GPS BCM4751 */
+	};
+
+	serial@70006200 {
+		compatible = "nvidia,tegra20-hsuart";
+		/delete-property/ reg-shift;
+		status = "okay";
+
+		/* Azurewave AW-NH615 BCM4329B1 */
+		bluetooth {
+			compatible = "brcm,bcm4329-bt";
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(U, 6) IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "host-wakeup";
+
+			/* PLLP 216MHz / 16 / 4 */
+			max-speed = <3375000>;
+
+			clocks = <&tegra_pmc TEGRA_PMC_CLK_BLINK>;
+			clock-names = "txco";
+
+			vbat-supply  = <&vdd_3v3_sys>;
+			vddio-supply = <&vdd_1v8_sys>;
+
+			device-wakeup-gpios = <&gpio TEGRA_GPIO(U, 1) GPIO_ACTIVE_HIGH>;
+			shutdown-gpios = <&gpio TEGRA_GPIO(U, 0) GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	serial@70006300 {
+		status = "okay";
+	};
+
+	pwm@7000a000 {
+		status = "okay";
+	};
+
+	i2c@7000c000 {
+		status = "okay";
+		clock-frequency = <400000>;
+
+		/* Aichi AMI306 digital compass */
+		magnetometer@e {
+			compatible = "asahi-kasei,ak8974";
+			reg = <0xe>;
+
+			avdd-supply = <&vdd_3v3_sys>;
+			dvdd-supply = <&vdd_1v8_sys>;
+
+			mount-matrix = "-1",  "0",  "0",
+					"0",  "1",  "0",
+					"0",  "0", "-1";
+		};
+
+		wm8903: audio-codec@1a {
+			compatible = "wlf,wm8903";
+			reg = <0x1a>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(X, 1) IRQ_TYPE_EDGE_BOTH>;
+
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			micdet-cfg = <0x83>;
+			micdet-delay = <100>;
+
+			gpio-cfg = <
+				0xffffffff /* don't touch */
+				0xffffffff /* don't touch */
+				0x00000000 /* Speaker-enable GPIO, output, low */
+				0x00000400 /* Mic bias current detect */
+				0xffffffff /* don't touch */
+			>;
+
+			AVDD-supply  = <&vdd_1v8_sys>;
+			CPVDD-supply = <&vdd_1v8_sys>;
+			DBVDD-supply = <&vdd_1v8_sys>;
+			DCVDD-supply = <&vdd_1v8_sys>;
+		};
+
+		/* Atmel MXT1386 Touchscreen */
+		touchscreen@5b {
+			compatible = "atmel,maxtouch";
+			reg = <0x5b>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(V, 6) IRQ_TYPE_LEVEL_LOW>;
+
+			reset-gpios = <&gpio TEGRA_GPIO(Q, 7) GPIO_ACTIVE_LOW>;
+
+			vdda-supply = <&vdd_3v3_sys>;
+			vdd-supply  = <&vdd_3v3_sys>;
+
+			atmel,wakeup-method = <ATMEL_MXT_WAKEUP_I2C_SCL>;
+		};
+
+		gyroscope@68 {
+			compatible = "invensense,mpu3050";
+			reg = <0x68>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(Z, 4) IRQ_TYPE_EDGE_RISING>;
+
+			vdd-supply    = <&vdd_3v3_sys>;
+			vlogic-supply = <&vdd_1v8_sys>;
+
+			mount-matrix =	 "0",  "1",  "0",
+					"-1",  "0",  "0",
+					 "0",  "0",  "1";
+
+			i2c-gate {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				accelerometer@f {
+					compatible = "kionix,kxtf9";
+					reg = <0xf>;
+
+					interrupt-parent = <&gpio>;
+					interrupts = <TEGRA_GPIO(N, 4) IRQ_TYPE_EDGE_RISING>;
+
+					vdd-supply = <&vdd_1v8_sys>;
+					vddio-supply = <&vdd_1v8_sys>;
+
+					mount-matrix =	 "1",  "0",  "0",
+							 "0",  "1",  "0",
+							 "0",  "0",  "1";
+				};
+			};
+		};
+	};
+
+	i2c2: i2c@7000c400 {
+		status = "okay";
+		clock-frequency = <100000>;
+	};
+
+	i2c@7000c500 {
+		status = "okay";
+		clock-frequency = <400000>;
+	};
+
+	i2c@7000d000 {
+		status = "okay";
+		clock-frequency = <400000>;
+
+		pmic: pmic@34 {
+			compatible = "ti,tps6586x";
+			reg = <0x34>;
+			interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
+
+			ti,system-power-controller;
+
+			#gpio-cells = <2>;
+			gpio-controller;
+
+			sys-supply = <&vdd_5v0_sys>;
+			vin-sm0-supply = <&sys_reg>;
+			vin-sm1-supply = <&sys_reg>;
+			vin-sm2-supply = <&sys_reg>;
+			vinldo01-supply = <&sm2_reg>;
+			vinldo23-supply = <&sm2_reg>;
+			vinldo4-supply = <&sm2_reg>;
+			vinldo678-supply = <&sm2_reg>;
+			vinldo9-supply = <&sm2_reg>;
+
+			regulators {
+				sys_reg: sys {
+					regulator-name = "vdd_sys";
+					regulator-always-on;
+				};
+
+				vdd_core: sm0 {
+					regulator-name = "vdd_sm0,vdd_core";
+					regulator-min-microvolt = <950000>;
+					regulator-max-microvolt = <1300000>;
+					regulator-coupled-with = <&rtc_vdd &vdd_cpu>;
+					regulator-coupled-max-spread = <170000 550000>;
+					regulator-always-on;
+					regulator-boot-on;
+
+					nvidia,tegra-core-regulator;
+				};
+
+				vdd_cpu: sm1 {
+					regulator-name = "vdd_sm1,vdd_cpu";
+					regulator-min-microvolt = <750000>;
+					regulator-max-microvolt = <1125000>;
+					regulator-coupled-with = <&vdd_core &rtc_vdd>;
+					regulator-coupled-max-spread = <550000 550000>;
+					regulator-always-on;
+					regulator-boot-on;
+
+					nvidia,tegra-cpu-regulator;
+				};
+
+				sm2_reg: sm2 {
+					regulator-name = "vdd_sm2,vin_ldo*";
+					regulator-min-microvolt = <3700000>;
+					regulator-max-microvolt = <3700000>;
+					regulator-always-on;
+				};
+
+				/* LDO0 is not connected to anything */
+
+				ldo1 {
+					regulator-name = "vdd_ldo1,avdd_pll*";
+					regulator-min-microvolt = <1100000>;
+					regulator-max-microvolt = <1100000>;
+					regulator-always-on;
+				};
+
+				rtc_vdd: ldo2 {
+					regulator-name = "vdd_ldo2,vdd_rtc";
+					regulator-min-microvolt = <950000>;
+					regulator-max-microvolt = <1300000>;
+					regulator-coupled-with = <&vdd_core &vdd_cpu>;
+					regulator-coupled-max-spread = <170000 550000>;
+					regulator-always-on;
+					regulator-boot-on;
+
+					nvidia,tegra-rtc-regulator;
+				};
+
+				ldo3 {
+					regulator-name = "vdd_ldo3,avdd_usb*";
+					regulator-min-microvolt = <3300000>;
+					regulator-max-microvolt = <3300000>;
+					regulator-always-on;
+				};
+
+				ldo4 {
+					regulator-name = "vdd_ldo4,avdd_osc,vddio_sys";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+				};
+
+				vcore_emmc: ldo5 {
+					regulator-name = "vdd_ldo5,vcore_mmc";
+					regulator-min-microvolt = <2850000>;
+					regulator-max-microvolt = <2850000>;
+					regulator-always-on;
+				};
+
+				ldo6 {
+					regulator-name = "vdd_ldo6,avdd_vdac";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+				};
+
+				hdmi_vdd_reg: ldo7 {
+					regulator-name = "vdd_ldo7,avdd_hdmi,vdd_fuse";
+					regulator-min-microvolt = <3300000>;
+					regulator-max-microvolt = <3300000>;
+				};
+
+				hdmi_pll_reg: ldo8 {
+					regulator-name = "vdd_ldo8,avdd_hdmi_pll";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+				};
+
+				ldo9 {
+					regulator-name = "vdd_ldo9,avdd_2v85,vdd_ddr_rx";
+					regulator-min-microvolt = <2850000>;
+					regulator-max-microvolt = <2850000>;
+					regulator-always-on;
+				};
+
+				ldo_rtc {
+					regulator-name = "vdd_rtc_out,vdd_cell";
+					regulator-min-microvolt = <3300000>;
+					regulator-max-microvolt = <3300000>;
+					regulator-always-on;
+				};
+			};
+		};
+
+		nct1008: temperature-sensor@4c {
+			compatible = "onnn,nct1008";
+			reg = <0x4c>;
+			vcc-supply = <&vdd_3v3_sys>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(N, 6) IRQ_TYPE_EDGE_FALLING>;
+
+			#thermal-sensor-cells = <1>;
+		};
+	};
+
+	pmc@7000e400 {
+		nvidia,invert-interrupt;
+		nvidia,suspend-mode = <1>;
+		nvidia,cpu-pwr-good-time = <2000>;
+		nvidia,cpu-pwr-off-time = <100>;
+		nvidia,core-pwr-good-time = <3845 3845>;
+		nvidia,core-pwr-off-time = <458>;
+		nvidia,sys-clock-req-active-high;
+		core-supply = <&vdd_core>;
+	};
+
+	memory-controller@7000f400 {
+		nvidia,use-ram-code;
+
+		emc-tables@3 {
+			reg = <0x3>;
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			lpddr2 {
+				compatible = "elpida,B8132B2PB-6D-F", "jedec,lpddr2-s4";
+				revision-id = <1 0>;
+				density = <2048>;
+				io-width = <16>;
+			};
+
+			emc-table@25000 {
+				reg = <25000>;
+				compatible = "nvidia,tegra20-emc-table";
+				clock-frequency = <25000>;
+				nvidia,emc-registers = <0x00000002 0x00000006
+					0x00000003 0x00000003 0x00000006 0x00000004
+					0x00000002 0x00000009 0x00000003 0x00000003
+					0x00000002 0x00000002 0x00000002 0x00000004
+					0x00000003 0x00000008 0x0000000b 0x0000004d
+					0x00000000 0x00000003 0x00000003 0x00000003
+					0x00000008 0x00000001 0x0000000a 0x00000004
+					0x00000003 0x00000008 0x00000004 0x00000006
+					0x00000002 0x00000068 0x00000000 0x00000003
+					0x00000000 0x00000000 0x00000282 0xa0ae04ae
+					0x00070000 0x00000000 0x00000000 0x00000003
+					0x00000000 0x00000000 0x00000000 0x00000000>;
+			};
+
+			emc-table@50000 {
+				reg = <50000>;
+				compatible = "nvidia,tegra20-emc-table";
+				clock-frequency = <50000>;
+				nvidia,emc-registers = <0x00000003 0x00000007
+					0x00000003 0x00000003 0x00000006 0x00000004
+					0x00000002 0x00000009 0x00000003 0x00000003
+					0x00000002 0x00000002 0x00000002 0x00000005
+					0x00000003 0x00000008 0x0000000b 0x0000009f
+					0x00000000 0x00000003 0x00000003 0x00000003
+					0x00000008 0x00000001 0x0000000a 0x00000007
+					0x00000003 0x00000008 0x00000004 0x00000006
+					0x00000002 0x000000d0 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000282 0xa0ae04ae
+					0x00070000 0x00000000 0x00000000 0x00000005
+					0x00000000 0x00000000 0x00000000 0x00000000>;
+			};
+
+			emc-table@75000 {
+				reg = <75000>;
+				compatible = "nvidia,tegra20-emc-table";
+				clock-frequency = <75000>;
+				nvidia,emc-registers = <0x00000005 0x0000000a
+					0x00000004 0x00000003 0x00000006 0x00000004
+					0x00000002 0x00000009 0x00000003 0x00000003
+					0x00000002 0x00000002 0x00000002 0x00000005
+					0x00000003 0x00000008 0x0000000b 0x000000ff
+					0x00000000 0x00000003 0x00000003 0x00000003
+					0x00000008 0x00000001 0x0000000a 0x0000000b
+					0x00000003 0x00000008 0x00000004 0x00000006
+					0x00000002 0x00000138 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000282 0xa0ae04ae
+					0x00070000 0x00000000 0x00000000 0x00000007
+					0x00000000 0x00000000 0x00000000 0x00000000>;
+			};
+
+			emc-table@150000 {
+				reg = <150000>;
+				compatible = "nvidia,tegra20-emc-table";
+				clock-frequency = <150000>;
+				nvidia,emc-registers = <0x00000009 0x00000014
+					0x00000007 0x00000003 0x00000006 0x00000004
+					0x00000002 0x00000009 0x00000003 0x00000003
+					0x00000002 0x00000002 0x00000002 0x00000005
+					0x00000003 0x00000008 0x0000000b 0x0000021f
+					0x00000000 0x00000003 0x00000003 0x00000003
+					0x00000008 0x00000001 0x0000000a 0x00000015
+					0x00000003 0x00000008 0x00000004 0x00000006
+					0x00000002 0x00000270 0x00000000 0x00000001
+					0x00000000 0x00000000 0x00000282 0xa07c04ae
+					0x007dc010 0x00000000 0x00000000 0x0000000e
+					0x00000000 0x00000000 0x00000000 0x00000000>;
+			};
+
+			emc-table@300000 {
+				reg = <300000>;
+				compatible = "nvidia,tegra20-emc-table";
+				clock-frequency = <300000>;
+				nvidia,emc-registers = <0x00000012 0x00000027
+					0x0000000d 0x00000006 0x00000007 0x00000005
+					0x00000003 0x00000009 0x00000006 0x00000006
+					0x00000003 0x00000003 0x00000002 0x00000006
+					0x00000003 0x00000009 0x0000000c 0x0000045f
+					0x00000000 0x00000004 0x00000004 0x00000006
+					0x00000008 0x00000001 0x0000000e 0x0000002a
+					0x00000003 0x0000000f 0x00000007 0x00000005
+					0x00000002 0x000004e0 0x00000005 0x00000002
+					0x00000000 0x00000000 0x00000282 0xe059048b
+					0x007e0010 0x00000000 0x00000000 0x0000001b
+					0x00000000 0x00000000 0x00000000 0x00000000>;
+			};
+		};
+	};
+
+	/* Peripheral USB via ASUS connector */
+	usb@c5000000 {
+		compatible = "nvidia,tegra20-udc";
+		status = "okay";
+		dr_mode = "peripheral";
+	};
+
+	usb-phy@c5000000 {
+		status = "okay";
+		dr_mode = "peripheral";
+		nvidia,xcvr-setup-use-fuses;
+		nvidia,xcvr-lsfslew = <2>;
+		nvidia,xcvr-lsrslew = <2>;
+		vbus-supply = <&vdd_5v0_sys>;
+	};
+
+	/* Dock's USB port */
+	usb@c5008000 {
+		status = "okay";
+	};
+
+	usb-phy@c5008000 {
+		status = "okay";
+		nvidia,xcvr-setup-use-fuses;
+		vbus-supply = <&vdd_5v0_sys>;
+	};
+
+	sdmmc1: mmc@c8000000 {
+		status = "okay";
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		assigned-clocks = <&tegra_car TEGRA20_CLK_SDMMC1>;
+		assigned-clock-parents = <&tegra_car TEGRA20_CLK_PLL_C>;
+		assigned-clock-rates = <40000000>;
+
+		max-frequency = <40000000>;
+		keep-power-in-suspend;
+		bus-width = <4>;
+		non-removable;
+
+		mmc-pwrseq = <&brcm_wifi_pwrseq>;
+		vmmc-supply = <&vdd_3v3_sys>;
+		vqmmc-supply = <&vdd_3v3_sys>;
+
+		/* Azurewave AW-NH615 BCM4329B1 */
+		wifi@1 {
+			compatible = "brcm,bcm4329-fmac";
+			reg = <1>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(S, 0) IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "host-wake";
+		};
+	};
+
+	sdmmc3: mmc@c8000400 {
+		status = "okay";
+		bus-width = <4>;
+		cd-gpios = <&gpio TEGRA_GPIO(I, 5) GPIO_ACTIVE_LOW>;
+		wp-gpios = <&gpio TEGRA_GPIO(H, 1) GPIO_ACTIVE_HIGH>;
+		power-gpios = <&gpio TEGRA_GPIO(I, 6) GPIO_ACTIVE_HIGH>;
+		vmmc-supply = <&vdd_3v3_sys>;
+		vqmmc-supply = <&vdd_3v3_sys>;
+	};
+
+	sdmmc4: mmc@c8000600 {
+		status = "okay";
+		bus-width = <8>;
+		vmmc-supply = <&vcore_emmc>;
+		vqmmc-supply = <&vdd_3v3_sys>;
+		non-removable;
+	};
+
+	mains: ac-adapter-detect {
+		compatible = "gpio-charger";
+		charger-type = "mains";
+		gpios = <&gpio TEGRA_GPIO(V, 3) GPIO_ACTIVE_LOW>;
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+
+		enable-gpios = <&gpio TEGRA_GPIO(D, 4) GPIO_ACTIVE_HIGH>;
+		power-supply = <&vdd_3v3_sys>;
+		pwms = <&pwm 2 4000000>;
+
+		brightness-levels = <7 255>;
+		num-interpolated-steps = <248>;
+		default-brightness-level = <20>;
+	};
+
+	/* PMIC has a built-in 32KHz oscillator which is used by PMC */
+	clk32k_in: clock-32k-in {
+		compatible = "fixed-clock";
+		clock-frequency = <32768>;
+		#clock-cells = <0>;
+	};
+
+	cpus {
+		cpu0: cpu@0 {
+			cpu-supply = <&vdd_cpu>;
+			operating-points-v2 = <&cpu0_opp_table>;
+			#cooling-cells = <2>;
+		};
+
+		cpu1: cpu@1 {
+			cpu-supply = <&vdd_cpu>;
+			operating-points-v2 = <&cpu0_opp_table>;
+			#cooling-cells = <2>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		switch-dock-hall-sensor {
+			label = "Lid";
+			gpios = <&gpio TEGRA_GPIO(S, 4) GPIO_ACTIVE_LOW>;
+			linux,input-type = <EV_SW>;
+			linux,code = <SW_LID>;
+			debounce-interval = <500>;
+			wakeup-event-action = <EV_ACT_ASSERTED>;
+			wakeup-source;
+		};
+
+		key-power {
+			label = "Power";
+			gpios = <&gpio TEGRA_GPIO(V, 2) GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_POWER>;
+			debounce-interval = <10>;
+			wakeup-event-action = <EV_ACT_ASSERTED>;
+			wakeup-source;
+		};
+
+		key-volume-up {
+			label = "Volume Up";
+			gpios = <&gpio TEGRA_GPIO(Q, 5) GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+			debounce-interval = <10>;
+			wakeup-event-action = <EV_ACT_ASSERTED>;
+			wakeup-source;
+		};
+
+		key-volume-down {
+			label = "Volume Down";
+			gpios = <&gpio TEGRA_GPIO(Q, 4) GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEDOWN>;
+			debounce-interval = <10>;
+			wakeup-event-action = <EV_ACT_ASSERTED>;
+			wakeup-source;
+		};
+	};
+
+	display-panel {
+		compatible = "panel-lvds";
+
+		/* AUO B101EW05 using custom timings */
+
+		backlight = <&backlight>;
+		ddc-i2c-bus = <&lvds_ddc>;
+		power-supply = <&vdd_pnl_reg>;
+
+		width-mm = <218>;
+		height-mm = <135>;
+
+		data-mapping = "jeida-18";
+
+		panel-timing {
+			clock-frequency = <71200000>;
+			hactive = <1280>;
+			vactive = <800>;
+			hfront-porch = <8>;
+			hback-porch = <18>;
+			hsync-len = <184>;
+			vsync-len = <3>;
+			vfront-porch = <4>;
+			vback-porch = <8>;
+		};
+
+		port {
+			panel_input: endpoint {
+				remote-endpoint = <&lvds_encoder_output>;
+			};
+		};
+	};
+
+	i2cmux {
+		compatible = "i2c-mux-pinctrl";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		i2c-parent = <&i2c2>;
+
+		pinctrl-names = "ddc", "pta", "idle";
+		pinctrl-0 = <&state_i2cmux_ddc>;
+		pinctrl-1 = <&state_i2cmux_pta>;
+		pinctrl-2 = <&state_i2cmux_idle>;
+
+		hdmi_ddc: i2c@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		lvds_ddc: i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			smart-battery@b {
+				compatible = "ti,bq20z75", "sbs,sbs-battery";
+				reg = <0xb>;
+				sbs,i2c-retry-count = <2>;
+				sbs,poll-retry-count = <10>;
+				power-supplies = <&mains>;
+			};
+		};
+	};
+
+	lvds-encoder {
+		compatible = "ti,sn75lvds83", "lvds-encoder";
+
+		powerdown-gpios = <&gpio TEGRA_GPIO(B, 2) GPIO_ACTIVE_LOW>;
+		power-supply = <&vdd_3v3_sys>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				lvds_encoder_input: endpoint {
+					remote-endpoint = <&lcd_output>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				lvds_encoder_output: endpoint {
+					remote-endpoint = <&panel_input>;
+				};
+			};
+		};
+	};
+
+	vdd_5v0_sys: regulator-5v0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_5v0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+
+	vdd_3v3_sys: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_3v3_vs";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		vin-supply = <&vdd_5v0_sys>;
+	};
+
+	regulator-pcie {
+		compatible = "regulator-fixed";
+		regulator-name = "pcie_vdd";
+		regulator-min-microvolt = <1500000>;
+		regulator-max-microvolt = <1500000>;
+		gpio = <&pmic 0 GPIO_ACTIVE_HIGH>;
+		regulator-always-on;
+	};
+
+	vdd_pnl_reg: regulator-panel {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_pnl";
+		regulator-min-microvolt = <2800000>;
+		regulator-max-microvolt = <2800000>;
+		gpio = <&gpio TEGRA_GPIO(C, 6) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	vdd_1v8_sys: regulator-1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_1v8_vs";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
+		vin-supply = <&vdd_5v0_sys>;
+	};
+
+	vdd_hdmi_en: regulator-hdmi {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_5v0_hdmi_en";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		vin-supply = <&vdd_5v0_sys>;
+		gpio = <&gpio TEGRA_GPIO(V, 5) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	sound {
+		compatible = "asus,tegra-audio-wm8903-tf101",
+			     "nvidia,tegra-audio-wm8903";
+		nvidia,model = "Asus EeePad Transformer WM8903";
+
+		nvidia,audio-routing =
+			"Headphone Jack", "HPOUTR",
+			"Headphone Jack", "HPOUTL",
+			"Int Spk", "ROP",
+			"Int Spk", "RON",
+			"Int Spk", "LOP",
+			"Int Spk", "LON",
+			"Mic Jack", "MICBIAS",
+			"IN1L", "Mic Jack";
+
+		nvidia,i2s-controller = <&tegra_i2s1>;
+		nvidia,audio-codec = <&wm8903>;
+
+		nvidia,spkr-en-gpios = <&wm8903 2 GPIO_ACTIVE_HIGH>;
+		nvidia,hp-det-gpios = <&gpio TEGRA_GPIO(W, 2) GPIO_ACTIVE_LOW>;
+		nvidia,headset;
+
+		clocks = <&tegra_car TEGRA20_CLK_PLL_A>,
+			 <&tegra_car TEGRA20_CLK_PLL_A_OUT0>,
+			 <&tegra_car TEGRA20_CLK_CDEV1>;
+		clock-names = "pll_a", "pll_a_out0", "mclk";
+	};
+
+	thermal-zones {
+		/*
+		 * NCT1008 has two sensors:
+		 *
+		 *	0: internal that monitors ambient/skin temperature
+		 *	1: external that is connected to the CPU's diode
+		 *
+		 * Ideally we should use userspace thermal governor,
+		 * but it's a much more complex solution.  The "skin"
+		 * zone is a simpler solution which prevents TF101 from
+		 * getting too hot from a user's tactile perspective.
+		 * The CPU zone is intended to protect silicon from damage.
+		 */
+
+		skin-thermal {
+			polling-delay-passive = <1000>; /* milliseconds */
+			polling-delay = <5000>; /* milliseconds */
+
+			thermal-sensors = <&nct1008 0>;
+
+			trips {
+				trip0: skin-alert {
+					/* start throttling at 60C */
+					temperature = <60000>;
+					hysteresis = <200>;
+					type = "passive";
+				};
+
+				trip1: skin-crit {
+					/* shut down at 70C */
+					temperature = <70000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				map0 {
+					trip = <&trip0>;
+					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+
+		cpu-thermal {
+			polling-delay-passive = <1000>; /* milliseconds */
+			polling-delay = <5000>; /* milliseconds */
+
+			thermal-sensors = <&nct1008 1>;
+
+			trips {
+				trip2: cpu-alert {
+					/* throttle at 85C until temperature drops to 84.8C */
+					temperature = <85000>;
+					hysteresis = <200>;
+					type = "passive";
+				};
+
+				trip3: cpu-crit {
+					/* shut down at 90C */
+					temperature = <90000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				map1 {
+					trip = <&trip2>;
+					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+	};
+
+	brcm_wifi_pwrseq: wifi-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+
+		clocks = <&tegra_pmc TEGRA_PMC_CLK_BLINK>;
+		clock-names = "ext_clock";
+
+		reset-gpios = <&gpio TEGRA_GPIO(K, 6) GPIO_ACTIVE_LOW>;
+		post-power-on-delay-ms = <200>;
+		power-off-delay-us = <200>;
+	};
+};
+
+&emc_icc_dvfs_opp_table {
+	/delete-node/ opp-666000000;
+	/delete-node/ opp-760000000;
+};
diff --git a/arch/arm/boot/dts/tegra20-colibri-eval-v3.dts b/arch/arm/boot/dts/tegra20-colibri-eval-v3.dts
index a05fb3853da8..cb1190b77db3 100644
--- a/arch/arm/boot/dts/tegra20-colibri-eval-v3.dts
+++ b/arch/arm/boot/dts/tegra20-colibri-eval-v3.dts
@@ -70,11 +70,11 @@
 				nvidia,tristate = <TEGRA_PIN_DISABLE>;
 			};
 
-			pwm-a-b {
+			sdc {
 				nvidia,tristate = <TEGRA_PIN_DISABLE>;
 			};
 
-			pwm-c-d {
+			sdb_sdd {
 				nvidia,tristate = <TEGRA_PIN_DISABLE>;
 			};
 
@@ -209,7 +209,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		wakeup {
+		key-wakeup {
 			label = "SODIMM pin 45 wakeup";
 			gpios = <&gpio TEGRA_GPIO(V, 3) GPIO_ACTIVE_HIGH>;
 			linux,code = <KEY_WAKEUP>;
diff --git a/arch/arm/boot/dts/tegra20-colibri-iris.dts b/arch/arm/boot/dts/tegra20-colibri-iris.dts
index 425494b9ed54..53487cc21513 100644
--- a/arch/arm/boot/dts/tegra20-colibri-iris.dts
+++ b/arch/arm/boot/dts/tegra20-colibri-iris.dts
@@ -70,11 +70,11 @@
 				nvidia,tristate = <TEGRA_PIN_DISABLE>;
 			};
 
-			pwm-a-b {
+			sdc {
 				nvidia,tristate = <TEGRA_PIN_DISABLE>;
 			};
 
-			pwm-c-d {
+			sdb_sdd {
 				nvidia,tristate = <TEGRA_PIN_DISABLE>;
 			};
 
@@ -191,7 +191,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		wakeup {
+		key-wakeup {
 			label = "SODIMM pin 45 wakeup";
 			gpios = <&gpio TEGRA_GPIO(V, 3) GPIO_ACTIVE_HIGH>;
 			linux,code = <KEY_WAKEUP>;
diff --git a/arch/arm/boot/dts/tegra20-colibri.dtsi b/arch/arm/boot/dts/tegra20-colibri.dtsi
index 585a5b441cf6..8ebd8afc857d 100644
--- a/arch/arm/boot/dts/tegra20-colibri.dtsi
+++ b/arch/arm/boot/dts/tegra20-colibri.dtsi
@@ -113,7 +113,7 @@
 			};
 
 			/* Colibri Backlight PWM<A>, PWM<B> */
-			pwm-a-b {
+			sdc {
 				nvidia,pins = "sdc";
 				nvidia,function = "pwm";
 				nvidia,tristate = <TEGRA_PIN_ENABLE>;
@@ -242,7 +242,7 @@
 			};
 
 			/* Colibri PWM<C>, PWM<D> */
-			pwm-c-d {
+			sdb_sdd {
 				nvidia,pins = "sdb", "sdd";
 				nvidia,function = "pwm";
 				nvidia,tristate = <TEGRA_PIN_ENABLE>;
@@ -428,10 +428,12 @@
 
 	serial@70006040 {
 		compatible = "nvidia,tegra20-hsuart";
+		/delete-property/ reg-shift;
 	};
 
 	serial@70006300 {
 		compatible = "nvidia,tegra20-hsuart";
+		/delete-property/ reg-shift;
 	};
 
 	nand-controller@70008000 {
@@ -495,7 +497,7 @@
 					regulator-always-on;
 				};
 
-				sm0 {
+				vdd_core: sm0 {
 					regulator-name = "VDD_CORE_1.2V";
 					regulator-min-microvolt = <1200000>;
 					regulator-max-microvolt = <1200000>;
@@ -601,6 +603,7 @@
 		nvidia,core-pwr-good-time = <3845 3845>;
 		nvidia,core-pwr-off-time = <3875>;
 		nvidia,sys-clock-req-active-high;
+		core-supply = <&vdd_core>;
 
 		/* Set SLEEP MODE bit in SUPPLYENE register of TPS658643 PMIC */
 		i2c-thermtrip {
@@ -688,7 +691,8 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		asix@1 {
+		ethernet@1 {
+			compatible = "usbb95,772b";
 			reg = <1>;
 			local-mac-address = [00 00 00 00 00 00];
 		};
@@ -743,11 +747,11 @@
 };
 
 &emc_icc_dvfs_opp_table {
-	/delete-node/ opp@760000000;
+	/delete-node/ opp-760000000;
 };
 
 &gpio {
-	lan-reset-n {
+	lan-reset-n-hog {
 		gpio-hog;
 		gpios = <TEGRA_GPIO(V, 4) GPIO_ACTIVE_HIGH>;
 		output-high;
@@ -755,7 +759,7 @@
 	};
 
 	/* Tri-stating GMI_WR_N on SODIMM pin 99 nPWE */
-	npwe {
+	npwe-hog {
 		gpio-hog;
 		gpios = <TEGRA_GPIO(T, 5) GPIO_ACTIVE_HIGH>;
 		output-high;
@@ -763,7 +767,7 @@
 	};
 
 	/* Not tri-stating GMI_WR_N on SODIMM pin 93 RDnWR */
-	rdnwr {
+	rdnwr-hog {
 		gpio-hog;
 		gpios = <TEGRA_GPIO(T, 6) GPIO_ACTIVE_HIGH>;
 		output-low;
diff --git a/arch/arm/boot/dts/tegra20-cpu-opp-microvolt.dtsi b/arch/arm/boot/dts/tegra20-cpu-opp-microvolt.dtsi
index 6f3e8c5fc5f0..7330c1b13d93 100644
--- a/arch/arm/boot/dts/tegra20-cpu-opp-microvolt.dtsi
+++ b/arch/arm/boot/dts/tegra20-cpu-opp-microvolt.dtsi
@@ -1,164 +1,164 @@
 // SPDX-License-Identifier: GPL-2.0
 
 / {
-	cpu0_opp_table: cpu_opp_table0 {
-		opp@216000000,750 {
+	cpu0_opp_table: opp-table-cpu0 {
+		opp-216000000-750 {
 			opp-microvolt = <750000 750000 1125000>;
 		};
 
-		opp@216000000,800 {
+		opp-216000000-800 {
 			opp-microvolt = <800000 800000 1125000>;
 		};
 
-		opp@312000000,750 {
+		opp-312000000-750 {
 			opp-microvolt = <750000 750000 1125000>;
 		};
 
-		opp@312000000,800 {
+		opp-312000000-800 {
 			opp-microvolt = <800000 800000 1125000>;
 		};
 
-		opp@456000000,750 {
+		opp-456000000-750 {
 			opp-microvolt = <750000 750000 1125000>;
 		};
 
-		opp@456000000,800 {
+		opp-456000000-800 {
 			opp-microvolt = <800000 800000 1125000>;
 		};
 
-		opp@456000000,825 {
+		opp-456000000-825 {
 			opp-microvolt = <825000 825000 1125000>;
 		};
 
-		opp@608000000,750 {
+		opp-608000000-750 {
 			opp-microvolt = <750000 750000 1125000>;
 		};
 
-		opp@608000000,800 {
+		opp-608000000-800 {
 			opp-microvolt = <800000 800000 1125000>;
 		};
 
-		opp@608000000,825 {
+		opp-608000000-825 {
 			opp-microvolt = <825000 825000 1125000>;
 		};
 
-		opp@608000000,850 {
+		opp-608000000-850 {
 			opp-microvolt = <850000 850000 1125000>;
 		};
 
-		opp@608000000,900 {
+		opp-608000000-900 {
 			opp-microvolt = <900000 900000 1125000>;
 		};
 
-		opp@760000000,775 {
+		opp-760000000-775 {
 			opp-microvolt = <775000 775000 1125000>;
 		};
 
-		opp@760000000,800 {
+		opp-760000000-800 {
 			opp-microvolt = <800000 800000 1125000>;
 		};
 
-		opp@760000000,850 {
+		opp-760000000-850 {
 			opp-microvolt = <850000 850000 1125000>;
 		};
 
-		opp@760000000,875 {
+		opp-760000000-875 {
 			opp-microvolt = <875000 875000 1125000>;
 		};
 
-		opp@760000000,900 {
+		opp-760000000-900 {
 			opp-microvolt = <900000 900000 1125000>;
 		};
 
-		opp@760000000,975 {
+		opp-760000000-975 {
 			opp-microvolt = <975000 975000 1125000>;
 		};
 
-		opp@816000000,800 {
+		opp-816000000-800 {
 			opp-microvolt = <800000 800000 1125000>;
 		};
 
-		opp@816000000,850 {
+		opp-816000000-850 {
 			opp-microvolt = <850000 850000 1125000>;
 		};
 
-		opp@816000000,875 {
+		opp-816000000-875 {
 			opp-microvolt = <875000 875000 1125000>;
 		};
 
-		opp@816000000,950 {
+		opp-816000000-950 {
 			opp-microvolt = <950000 950000 1125000>;
 		};
 
-		opp@816000000,1000 {
+		opp-816000000-1000 {
 			opp-microvolt = <1000000 1000000 1125000>;
 		};
 
-		opp@912000000,850 {
+		opp-912000000-850 {
 			opp-microvolt = <850000 850000 1125000>;
 		};
 
-		opp@912000000,900 {
+		opp-912000000-900 {
 			opp-microvolt = <900000 900000 1125000>;
 		};
 
-		opp@912000000,925 {
+		opp-912000000-925 {
 			opp-microvolt = <925000 925000 1125000>;
 		};
 
-		opp@912000000,950 {
+		opp-912000000-950 {
 			opp-microvolt = <950000 950000 1125000>;
 		};
 
-		opp@912000000,1000 {
+		opp-912000000-1000 {
 			opp-microvolt = <1000000 1000000 1125000>;
 		};
 
-		opp@912000000,1050 {
+		opp-912000000-1050 {
 			opp-microvolt = <1050000 1050000 1125000>;
 		};
 
-		opp@1000000000,875 {
+		opp-1000000000-875 {
 			opp-microvolt = <875000 875000 1125000>;
 		};
 
-		opp@1000000000,900 {
+		opp-1000000000-900 {
 			opp-microvolt = <900000 900000 1125000>;
 		};
 
-		opp@1000000000,950 {
+		opp-1000000000-950 {
 			opp-microvolt = <950000 950000 1125000>;
 		};
 
-		opp@1000000000,975 {
+		opp-1000000000-975 {
 			opp-microvolt = <975000 975000 1125000>;
 		};
 
-		opp@1000000000,1000 {
+		opp-1000000000-1000 {
 			opp-microvolt = <1000000 1000000 1125000>;
 		};
 
-		opp@1000000000,1025 {
+		opp-1000000000-1025 {
 			opp-microvolt = <1025000 1025000 1125000>;
 		};
 
-		opp@1000000000,1100 {
+		opp-1000000000-1100 {
 			opp-microvolt = <1100000 1100000 1125000>;
 		};
 
-		opp@1200000000,1000 {
+		opp-1200000000-1000 {
 			opp-microvolt = <1000000 1000000 1125000>;
 		};
 
-		opp@1200000000,1050 {
+		opp-1200000000-1050 {
 			opp-microvolt = <1050000 1050000 1125000>;
 		};
 
-		opp@1200000000,1100 {
+		opp-1200000000-1100 {
 			opp-microvolt = <1100000 1100000 1125000>;
 		};
 
-		opp@1200000000,1125 {
+		opp-1200000000-1125 {
 			opp-microvolt = <1125000 1125000 1125000>;
 		};
 	};
diff --git a/arch/arm/boot/dts/tegra20-cpu-opp.dtsi b/arch/arm/boot/dts/tegra20-cpu-opp.dtsi
index 135de316383b..47c8e78ca958 100644
--- a/arch/arm/boot/dts/tegra20-cpu-opp.dtsi
+++ b/arch/arm/boot/dts/tegra20-cpu-opp.dtsi
@@ -1,250 +1,250 @@
 // SPDX-License-Identifier: GPL-2.0
 
 / {
-	cpu0_opp_table: cpu_opp_table0 {
+	cpu0_opp_table: opp-table-cpu0 {
 		compatible = "operating-points-v2";
 		opp-shared;
 
-		opp@216000000,750 {
+		opp-216000000-750 {
 			clock-latency-ns = <400000>;
 			opp-supported-hw = <0x0F 0x0003>;
 			opp-hz = /bits/ 64 <216000000>;
 			opp-suspend;
 		};
 
-		opp@216000000,800 {
+		opp-216000000-800 {
 			clock-latency-ns = <400000>;
 			opp-supported-hw = <0x0F 0x0004>;
 			opp-hz = /bits/ 64 <216000000>;
 			opp-suspend;
 		};
 
-		opp@312000000,750 {
+		opp-312000000-750 {
 			clock-latency-ns = <400000>;
 			opp-supported-hw = <0x0F 0x0003>;
 			opp-hz = /bits/ 64 <312000000>;
 		};
 
-		opp@312000000,800 {
+		opp-312000000-800 {
 			clock-latency-ns = <400000>;
 			opp-supported-hw = <0x0F 0x0004>;
 			opp-hz = /bits/ 64 <312000000>;
 		};
 
-		opp@456000000,750 {
+		opp-456000000-750 {
 			clock-latency-ns = <400000>;
 			opp-supported-hw = <0x0C 0x0003>;
 			opp-hz = /bits/ 64 <456000000>;
 		};
 
-		opp@456000000,800 {
+		opp-456000000-800 {
 			clock-latency-ns = <400000>;
 			opp-supported-hw = <0x03 0x0006>, <0x04 0x0004>,
 					   <0x08 0x0004>;
 			opp-hz = /bits/ 64 <456000000>;
 		};
 
-		opp@456000000,825 {
+		opp-456000000-825 {
 			clock-latency-ns = <400000>;
 			opp-supported-hw = <0x03 0x0001>;
 			opp-hz = /bits/ 64 <456000000>;
 		};
 
-		opp@608000000,750 {
+		opp-608000000-750 {
 			clock-latency-ns = <400000>;
 			opp-supported-hw = <0x08 0x0003>;
 			opp-hz = /bits/ 64 <608000000>;
 		};
 
-		opp@608000000,800 {
+		opp-608000000-800 {
 			clock-latency-ns = <400000>;
 			opp-supported-hw = <0x04 0x0006>, <0x08 0x0004>;
 			opp-hz = /bits/ 64 <608000000>;
 		};
 
-		opp@608000000,825 {
+		opp-608000000-825 {
 			clock-latency-ns = <400000>;
 			opp-supported-hw = <0x04 0x0001>;
 			opp-hz = /bits/ 64 <608000000>;
 		};
 
-		opp@608000000,850 {
+		opp-608000000-850 {
 			clock-latency-ns = <400000>;
 			opp-supported-hw = <0x03 0x0006>;
 			opp-hz = /bits/ 64 <608000000>;
 		};
 
-		opp@608000000,900 {
+		opp-608000000-900 {
 			clock-latency-ns = <400000>;
 			opp-supported-hw = <0x03 0x0001>;
 			opp-hz = /bits/ 64 <608000000>;
 		};
 
-		opp@760000000,775 {
+		opp-760000000-775 {
 			clock-latency-ns = <400000>;
 			opp-supported-hw = <0x08 0x0003>;
 			opp-hz = /bits/ 64 <760000000>;
 		};
 
-		opp@760000000,800 {
+		opp-760000000-800 {
 			clock-latency-ns = <400000>;
 			opp-supported-hw = <0x08 0x0004>;
 			opp-hz = /bits/ 64 <760000000>;
 		};
 
-		opp@760000000,850 {
+		opp-760000000-850 {
 			clock-latency-ns = <400000>;
 			opp-supported-hw = <0x04 0x0006>;
 			opp-hz = /bits/ 64 <760000000>;
 		};
 
-		opp@760000000,875 {
+		opp-760000000-875 {
 			clock-latency-ns = <400000>;
 			opp-supported-hw = <0x04 0x0001>, <0x02 0x0002>,
 					   <0x01 0x0004>, <0x02 0x0004>;
 			opp-hz = /bits/ 64 <760000000>;
 		};
 
-		opp@760000000,900 {
+		opp-760000000-900 {
 			clock-latency-ns = <400000>;
 			opp-supported-hw = <0x01 0x0002>;
 			opp-hz = /bits/ 64 <760000000>;
 		};
 
-		opp@760000000,975 {
+		opp-760000000-975 {
 			clock-latency-ns = <400000>;
 			opp-supported-hw = <0x03 0x0001>;
 			opp-hz = /bits/ 64 <760000000>;
 		};
 
-		opp@816000000,800 {
+		opp-816000000-800 {
 			clock-latency-ns = <400000>;
 			opp-supported-hw = <0x08 0x0007>;
 			opp-hz = /bits/ 64 <816000000>;
 		};
 
-		opp@816000000,850 {
+		opp-816000000-850 {
 			clock-latency-ns = <400000>;
 			opp-supported-hw = <0x04 0x0002>;
 			opp-hz = /bits/ 64 <816000000>;
 		};
 
-		opp@816000000,875 {
+		opp-816000000-875 {
 			clock-latency-ns = <400000>;
 			opp-supported-hw = <0x04 0x0005>;
 			opp-hz = /bits/ 64 <816000000>;
 		};
 
-		opp@816000000,950 {
+		opp-816000000-950 {
 			clock-latency-ns = <400000>;
 			opp-supported-hw = <0x03 0x0006>;
 			opp-hz = /bits/ 64 <816000000>;
 		};
 
-		opp@816000000,1000 {
+		opp-816000000-1000 {
 			clock-latency-ns = <400000>;
 			opp-supported-hw = <0x03 0x0001>;
 			opp-hz = /bits/ 64 <816000000>;
 		};
 
-		opp@912000000,850 {
+		opp-912000000-850 {
 			clock-latency-ns = <400000>;
 			opp-supported-hw = <0x08 0x0007>;
 			opp-hz = /bits/ 64 <912000000>;
 		};
 
-		opp@912000000,900 {
+		opp-912000000-900 {
 			clock-latency-ns = <400000>;
 			opp-supported-hw = <0x04 0x0002>;
 			opp-hz = /bits/ 64 <912000000>;
 		};
 
-		opp@912000000,925 {
+		opp-912000000-925 {
 			clock-latency-ns = <400000>;
 			opp-supported-hw = <0x04 0x0001>;
 			opp-hz = /bits/ 64 <912000000>;
 		};
 
-		opp@912000000,950 {
+		opp-912000000-950 {
 			clock-latency-ns = <400000>;
 			opp-supported-hw = <0x02 0x0006>, <0x01 0x0004>,
 					   <0x04 0x0004>;
 			opp-hz = /bits/ 64 <912000000>;
 		};
 
-		opp@912000000,1000 {
+		opp-912000000-1000 {
 			clock-latency-ns = <400000>;
 			opp-supported-hw = <0x01 0x0002>;
 			opp-hz = /bits/ 64 <912000000>;
 		};
 
-		opp@912000000,1050 {
+		opp-912000000-1050 {
 			clock-latency-ns = <400000>;
 			opp-supported-hw = <0x03 0x0001>;
 			opp-hz = /bits/ 64 <912000000>;
 		};
 
-		opp@1000000000,875 {
+		opp-1000000000-875 {
 			clock-latency-ns = <400000>;
 			opp-supported-hw = <0x08 0x0007>;
 			opp-hz = /bits/ 64 <1000000000>;
 		};
 
-		opp@1000000000,900 {
+		opp-1000000000-900 {
 			clock-latency-ns = <400000>;
 			opp-supported-hw = <0x04 0x0002>;
 			opp-hz = /bits/ 64 <1000000000>;
 		};
 
-		opp@1000000000,950 {
+		opp-1000000000-950 {
 			clock-latency-ns = <400000>;
 			opp-supported-hw = <0x04 0x0004>;
 			opp-hz = /bits/ 64 <1000000000>;
 		};
 
-		opp@1000000000,975 {
+		opp-1000000000-975 {
 			clock-latency-ns = <400000>;
 			opp-supported-hw = <0x04 0x0001>;
 			opp-hz = /bits/ 64 <1000000000>;
 		};
 
-		opp@1000000000,1000 {
+		opp-1000000000-1000 {
 			clock-latency-ns = <400000>;
 			opp-supported-hw = <0x02 0x0006>, <0x01 0x0004>;
 			opp-hz = /bits/ 64 <1000000000>;
 		};
 
-		opp@1000000000,1025 {
+		opp-1000000000-1025 {
 			clock-latency-ns = <400000>;
 			opp-supported-hw = <0x01 0x0002>;
 			opp-hz = /bits/ 64 <1000000000>;
 		};
 
-		opp@1000000000,1100 {
+		opp-1000000000-1100 {
 			clock-latency-ns = <400000>;
 			opp-supported-hw = <0x03 0x0001>;
 			opp-hz = /bits/ 64 <1000000000>;
 		};
 
-		opp@1200000000,1000 {
+		opp-1200000000-1000 {
 			clock-latency-ns = <400000>;
 			opp-supported-hw = <0x08 0x0004>;
 			opp-hz = /bits/ 64 <1200000000>;
 		};
 
-		opp@1200000000,1050 {
+		opp-1200000000-1050 {
 			clock-latency-ns = <400000>;
 			opp-supported-hw = <0x04 0x0004>;
 			opp-hz = /bits/ 64 <1200000000>;
 		};
 
-		opp@1200000000,1100 {
+		opp-1200000000-1100 {
 			clock-latency-ns = <400000>;
 			opp-supported-hw = <0x02 0x0004>;
 			opp-hz = /bits/ 64 <1200000000>;
 		};
 
-		opp@1200000000,1125 {
+		opp-1200000000-1125 {
 			clock-latency-ns = <400000>;
 			opp-supported-hw = <0x01 0x0004>;
 			opp-hz = /bits/ 64 <1200000000>;
diff --git a/arch/arm/boot/dts/tegra20-harmony.dts b/arch/arm/boot/dts/tegra20-harmony.dts
index ae4312eedcbd..11f21aeba8e9 100644
--- a/arch/arm/boot/dts/tegra20-harmony.dts
+++ b/arch/arm/boot/dts/tegra20-harmony.dts
@@ -339,7 +339,7 @@
 					regulator-always-on;
 				};
 
-				sm0 {
+				vdd_core: sm0 {
 					regulator-name = "vdd_sm0,vdd_core";
 					regulator-min-microvolt = <1200000>;
 					regulator-max-microvolt = <1200000>;
@@ -565,6 +565,7 @@
 		nvidia,core-pwr-good-time = <3845 3845>;
 		nvidia,core-pwr-off-time = <3875>;
 		nvidia,sys-clock-req-active-high;
+		core-supply = <&vdd_core>;
 	};
 
 	pcie@80003000 {
@@ -595,8 +596,6 @@
 
 	usb@c5004000 {
 		status = "okay";
-		nvidia,phy-reset-gpio = <&gpio TEGRA_GPIO(V, 1)
-			GPIO_ACTIVE_LOW>;
 	};
 
 	usb-phy@c5004000 {
@@ -640,7 +639,7 @@
 		default-brightness-level = <6>;
 	};
 
-	clk32k_in: clock@0 {
+	clk32k_in: clock-32k {
 		compatible = "fixed-clock";
 		clock-frequency = <32768>;
 		#clock-cells = <0>;
@@ -649,7 +648,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		power {
+		key-power {
 			label = "Power";
 			gpios = <&gpio TEGRA_GPIO(V, 2) GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
@@ -666,7 +665,7 @@
 		backlight = <&backlight>;
 	};
 
-	vdd_5v0_reg: regulator@0 {
+	vdd_5v0_reg: regulator-5v0 {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd_5v0";
 		regulator-min-microvolt = <5000000>;
@@ -674,7 +673,7 @@
 		regulator-always-on;
 	};
 
-	regulator@1 {
+	regulator-1v5 {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd_1v5";
 		regulator-min-microvolt = <1500000>;
@@ -682,7 +681,7 @@
 		gpio = <&pmic 0 GPIO_ACTIVE_HIGH>;
 	};
 
-	regulator@2 {
+	regulator-1v2 {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd_1v2";
 		regulator-min-microvolt = <1200000>;
@@ -691,7 +690,7 @@
 		enable-active-high;
 	};
 
-	pci_vdd_reg: regulator@3 {
+	pci_vdd_reg: regulator-1v05 {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd_1v05";
 		regulator-min-microvolt = <1050000>;
@@ -700,7 +699,7 @@
 		enable-active-high;
 	};
 
-	vdd_pnl_reg: regulator@4 {
+	vdd_pnl_reg: regulator-pn1 {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd_pnl";
 		regulator-min-microvolt = <2800000>;
@@ -709,7 +708,7 @@
 		enable-active-high;
 	};
 
-	vdd_bl_reg: regulator@5 {
+	vdd_bl_reg: regulator-bl {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd_bl";
 		regulator-min-microvolt = <2800000>;
@@ -718,7 +717,7 @@
 		enable-active-high;
 	};
 
-	vdd_5v0_hdmi: regulator@6 {
+	vdd_5v0_hdmi: regulator-hdmi {
 		compatible = "regulator-fixed";
 		regulator-name = "VDDIO_HDMI";
 		regulator-min-microvolt = <5000000>;
diff --git a/arch/arm/boot/dts/tegra20-medcom-wide.dts b/arch/arm/boot/dts/tegra20-medcom-wide.dts
index b31c9bca16e6..f144487c5da3 100644
--- a/arch/arm/boot/dts/tegra20-medcom-wide.dts
+++ b/arch/arm/boot/dts/tegra20-medcom-wide.dts
@@ -54,6 +54,9 @@
 
 		brightness-levels = <0 4 8 16 32 64 128 255>;
 		default-brightness-level = <6>;
+
+		/* close enough */
+		power-supply = <&vdd_3v3_reg>;
 	};
 
 	panel: panel {
@@ -92,7 +95,7 @@
 		clock-names = "pll_a", "pll_a_out0", "mclk";
 	};
 
-	vcc_24v_reg: regulator@100 {
+	vcc_24v_reg: regulator-24v0 {
 		compatible = "regulator-fixed";
 		regulator-name = "vcc_24v";
 		regulator-min-microvolt = <24000000>;
@@ -100,7 +103,7 @@
 		regulator-always-on;
 	};
 
-	vdd_5v0_reg: regulator@101 {
+	vdd_5v0_reg: regulator-5v0 {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd_5v0";
 		vin-supply = <&vcc_24v_reg>;
@@ -109,7 +112,7 @@
 		regulator-always-on;
 	};
 
-	vdd_3v3_reg: regulator@102 {
+	vdd_3v3_reg: regulator-3v3 {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd_3v3";
 		vin-supply = <&vcc_24v_reg>;
@@ -118,7 +121,7 @@
 		regulator-always-on;
 	};
 
-	vdd_1v8_reg: regulator@103 {
+	vdd_1v8_reg: regulator-1v8 {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd_1v8";
 		vin-supply = <&vdd_3v3_reg>;
diff --git a/arch/arm/boot/dts/tegra20-paz00.dts b/arch/arm/boot/dts/tegra20-paz00.dts
index 5b38b0606f99..48fe628c6d87 100644
--- a/arch/arm/boot/dts/tegra20-paz00.dts
+++ b/arch/arm/boot/dts/tegra20-paz00.dts
@@ -13,6 +13,8 @@
 	compatible = "compal,paz00", "nvidia,tegra20";
 
 	aliases {
+		mmc0 = &sdmmc4; /* eMMC */
+		mmc1 = &sdmmc1; /* MicroSD */
 		rtc0 = "/i2c@7000d000/tps6586x@34";
 		rtc1 = "/rtc@7000e000";
 		serial0 = &uarta;
@@ -264,8 +266,16 @@
 		};
 	};
 
+	spdif@70002400 {
+		status = "okay";
+
+		nvidia,fixed-parent-rate;
+	};
+
 	i2s@70002800 {
 		status = "okay";
+
+		nvidia,fixed-parent-rate;
 	};
 
 	serial@70006000 {
@@ -519,6 +529,7 @@
 		nvidia,core-pwr-good-time = <3845 3845>;
 		nvidia,core-pwr-off-time = <0>;
 		nvidia,sys-clock-req-active-high;
+		core-supply = <&core_vdd_reg>;
 	};
 
 	usb@c5000000 {
@@ -533,8 +544,6 @@
 
 	usb@c5004000 {
 		status = "okay";
-		nvidia,phy-reset-gpio = <&gpio TEGRA_GPIO(V, 0)
-			GPIO_ACTIVE_LOW>;
 	};
 
 	usb-phy@c5004000 {
@@ -551,7 +560,7 @@
 		status = "okay";
 	};
 
-	mmc@c8000000 {
+	sdmmc1: mmc@c8000000 {
 		status = "okay";
 		cd-gpios = <&gpio TEGRA_GPIO(V, 5) GPIO_ACTIVE_LOW>;
 		wp-gpios = <&gpio TEGRA_GPIO(H, 1) GPIO_ACTIVE_HIGH>;
@@ -559,7 +568,7 @@
 		bus-width = <4>;
 	};
 
-	mmc@c8000600 {
+	sdmmc4: mmc@c8000600 {
 		status = "okay";
 		bus-width = <8>;
 		non-removable;
@@ -573,9 +582,12 @@
 
 		brightness-levels = <0 16 32 48 64 80 96 112 128 144 160 176 192 208 224 240 255>;
 		default-brightness-level = <10>;
+
+		/* close enough */
+		power-supply = <&vdd_pnl_reg>;
 	};
 
-	clk32k_in: clock@0 {
+	clk32k_in: clock-32k {
 		compatible = "fixed-clock";
 		clock-frequency = <32768>;
 		#clock-cells = <0>;
@@ -584,7 +596,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		wakeup {
+		key-wakeup {
 			label = "Wakeup";
 			gpios = <&gpio TEGRA_GPIO(J, 7) GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_WAKEUP>;
@@ -612,7 +624,7 @@
 		backlight = <&backlight>;
 	};
 
-	p5valw_reg: regulator@0 {
+	p5valw_reg: regulator-5v0alw {
 		compatible = "regulator-fixed";
 		regulator-name = "+5valw";
 		regulator-min-microvolt = <5000000>;
@@ -620,7 +632,7 @@
 		regulator-always-on;
 	};
 
-	vdd_pnl_reg: regulator@1 {
+	vdd_pnl_reg: regulator-3v0 {
 		compatible = "regulator-fixed";
 		regulator-name = "+3VS,vdd_pnl";
 		regulator-min-microvolt = <3300000>;
@@ -705,5 +717,5 @@
 };
 
 &emc_icc_dvfs_opp_table {
-	/delete-node/ opp@760000000;
+	/delete-node/ opp-760000000;
 };
diff --git a/arch/arm/boot/dts/tegra20-peripherals-opp.dtsi b/arch/arm/boot/dts/tegra20-peripherals-opp.dtsi
index ef3ad2e5f270..1b808233a933 100644
--- a/arch/arm/boot/dts/tegra20-peripherals-opp.dtsi
+++ b/arch/arm/boot/dts/tegra20-peripherals-opp.dtsi
@@ -1,110 +1,1022 @@
 // SPDX-License-Identifier: GPL-2.0
 
 / {
-	emc_icc_dvfs_opp_table: emc-dvfs-opp-table {
+	core_opp_table: opp-table-core {
 		compatible = "operating-points-v2";
+		opp-shared;
 
-		opp@36000000 {
+		core_opp_950: opp-950000 {
+			opp-microvolt = <950000 950000 1300000>;
+			opp-level = <950000>;
+		};
+
+		core_opp_1000: opp-1000000 {
+			opp-microvolt = <1000000 1000000 1300000>;
+			opp-level = <1000000>;
+		};
+
+		core_opp_1100: opp-1100000 {
+			opp-microvolt = <1100000 1100000 1300000>;
+			opp-level = <1100000>;
+		};
+
+		core_opp_1200: opp-1200000 {
+			opp-microvolt = <1200000 1200000 1300000>;
+			opp-level = <1200000>;
+		};
+
+		core_opp_1225: opp-1225000 {
+			opp-microvolt = <1225000 1225000 1300000>;
+			opp-level = <1225000>;
+		};
+
+		core_opp_1275: opp-1275000 {
+			opp-microvolt = <1275000 1275000 1300000>;
+			opp-level = <1275000>;
+		};
+
+		core_opp_1300: opp-1300000 {
+			opp-microvolt = <1300000 1300000 1300000>;
+			opp-level = <1300000>;
+		};
+	};
+
+	emc_icc_dvfs_opp_table: opp-table-emc {
+		compatible = "operating-points-v2";
+
+		opp-36000000 {
 			opp-microvolt = <950000 950000 1300000>;
 			opp-hz = /bits/ 64 <36000000>;
 			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_950>;
 		};
 
-		opp@47500000 {
+		opp-47500000 {
 			opp-microvolt = <950000 950000 1300000>;
 			opp-hz = /bits/ 64 <47500000>;
 			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_950>;
 		};
 
-		opp@50000000 {
+		opp-50000000 {
 			opp-microvolt = <950000 950000 1300000>;
 			opp-hz = /bits/ 64 <50000000>;
 			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_950>;
 		};
 
-		opp@54000000 {
+		opp-54000000 {
 			opp-microvolt = <950000 950000 1300000>;
 			opp-hz = /bits/ 64 <54000000>;
 			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_950>;
 		};
 
-		opp@57000000 {
+		opp-57000000 {
 			opp-microvolt = <950000 950000 1300000>;
 			opp-hz = /bits/ 64 <57000000>;
 			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_950>;
 		};
 
-		opp@100000000 {
+		opp-100000000 {
 			opp-microvolt = <1000000 1000000 1300000>;
 			opp-hz = /bits/ 64 <100000000>;
 			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1000>;
 		};
 
-		opp@108000000 {
+		opp-108000000 {
 			opp-microvolt = <1000000 1000000 1300000>;
 			opp-hz = /bits/ 64 <108000000>;
 			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1000>;
 		};
 
-		opp@126666000 {
+		opp-126666000 {
 			opp-microvolt = <1000000 1000000 1300000>;
 			opp-hz = /bits/ 64 <126666000>;
 			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1000>;
 		};
 
-		opp@150000000 {
+		opp-150000000 {
 			opp-microvolt = <1000000 1000000 1300000>;
 			opp-hz = /bits/ 64 <150000000>;
 			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1000>;
 		};
 
-		opp@190000000 {
+		opp-190000000 {
 			opp-microvolt = <1000000 1000000 1300000>;
 			opp-hz = /bits/ 64 <190000000>;
 			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1000>;
 		};
 
-		opp@216000000 {
+		opp-216000000 {
 			opp-microvolt = <1000000 1000000 1300000>;
 			opp-hz = /bits/ 64 <216000000>;
 			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1000>;
 			opp-suspend;
 		};
 
-		opp@300000000 {
+		opp-300000000 {
 			opp-microvolt = <1000000 1000000 1300000>;
 			opp-hz = /bits/ 64 <300000000>;
 			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1000>;
 		};
 
-		opp@333000000 {
+		opp-333000000 {
 			opp-microvolt = <1000000 1000000 1300000>;
 			opp-hz = /bits/ 64 <333000000>;
 			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1000>;
 		};
 
-		opp@380000000 {
+		opp-380000000 {
 			opp-microvolt = <1100000 1100000 1300000>;
 			opp-hz = /bits/ 64 <380000000>;
 			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1100>;
 		};
 
-		opp@600000000 {
+		opp-600000000 {
 			opp-microvolt = <1200000 1200000 1300000>;
 			opp-hz = /bits/ 64 <600000000>;
 			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1200>;
 		};
 
-		opp@666000000 {
+		opp-666000000 {
 			opp-microvolt = <1200000 1200000 1300000>;
 			opp-hz = /bits/ 64 <666000000>;
 			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1200>;
 		};
 
-		opp@760000000 {
+		opp-760000000 {
 			opp-microvolt = <1300000 1300000 1300000>;
 			opp-hz = /bits/ 64 <760000000>;
 			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1300>;
+		};
+	};
+
+	host1x_dvfs_opp_table: opp-table-host1x {
+		compatible = "operating-points-v2";
+
+		opp-104500000-950 {
+			opp-microvolt = <950000 950000 1300000>;
+			opp-hz = /bits/ 64 <104500000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_950>;
+		};
+
+		opp-133000000-1000 {
+			opp-microvolt = <1000000 1000000 1300000>;
+			opp-hz = /bits/ 64 <133000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-166000000-1100 {
+			opp-microvolt = <1100000 1100000 1300000>;
+			opp-hz = /bits/ 64 <166000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1100>;
+		};
+	};
+
+	mpe_dvfs_opp_table: opp-table-mpe {
+		compatible = "operating-points-v2";
+
+		opp-104500000-950 {
+			opp-microvolt = <950000 950000 1300000>;
+			opp-hz = /bits/ 64 <104500000>;
+			opp-supported-hw = <0x0001>;
+			required-opps = <&core_opp_950>;
+		};
+
+		opp-142500000-950 {
+			opp-microvolt = <950000 950000 1300000>;
+			opp-hz = /bits/ 64 <142500000>;
+			opp-supported-hw = <0x0002>;
+			required-opps = <&core_opp_950>;
+		};
+
+		opp-152000000-1000 {
+			opp-microvolt = <1000000 1000000 1300000>;
+			opp-hz = /bits/ 64 <152000000>;
+			opp-supported-hw = <0x0001>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-190000000-1000 {
+			opp-microvolt = <1000000 1000000 1300000>;
+			opp-hz = /bits/ 64 <190000000>;
+			opp-supported-hw = <0x0002>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-190000000-950 {
+			opp-microvolt = <950000 950000 1300000>;
+			opp-hz = /bits/ 64 <190000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_950>;
+		};
+
+		opp-228000000-1100 {
+			opp-microvolt = <1100000 1100000 1300000>;
+			opp-hz = /bits/ 64 <228000000>;
+			opp-supported-hw = <0x0001>;
+			required-opps = <&core_opp_1100>;
+		};
+
+		opp-228000000-950 {
+			opp-microvolt = <950000 950000 1300000>;
+			opp-hz = /bits/ 64 <228000000>;
+			opp-supported-hw = <0x0008>;
+			required-opps = <&core_opp_950>;
+		};
+
+		opp-237500000-1000 {
+			opp-microvolt = <1000000 1000000 1300000>;
+			opp-hz = /bits/ 64 <237500000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-266000000-1000 {
+			opp-microvolt = <1000000 1000000 1300000>;
+			opp-hz = /bits/ 64 <266000000>;
+			opp-supported-hw = <0x0008>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-275500000-1100 {
+			opp-microvolt = <1100000 1100000 1300000>;
+			opp-hz = /bits/ 64 <275500000>;
+			opp-supported-hw = <0x0002>;
+			required-opps = <&core_opp_1100>;
+		};
+
+		opp-300000000-1200 {
+			opp-microvolt = <1200000 1200000 1300000>;
+			opp-hz = /bits/ 64 <300000000>;
+			opp-supported-hw = <0x0003>;
+			required-opps = <&core_opp_1200>;
+		};
+
+		opp-300000000-1100 {
+			opp-microvolt = <1100000 1100000 1300000>;
+			opp-hz = /bits/ 64 <300000000>;
+			opp-supported-hw = <0x000C>;
+			required-opps = <&core_opp_1100>;
+		};
+	};
+
+	vi_dvfs_opp_table: opp-table-vi {
+		compatible = "operating-points-v2";
+
+		opp-85000000-950 {
+			opp-microvolt = <950000 950000 1300000>;
+			opp-hz = /bits/ 64 <85000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_950>;
+		};
+
+		opp-100000000-1000 {
+			opp-microvolt = <1000000 1000000 1300000>;
+			opp-hz = /bits/ 64 <100000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-150000000-1100 {
+			opp-microvolt = <1100000 1100000 1300000>;
+			opp-hz = /bits/ 64 <150000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1100>;
+		};
+	};
+
+	epp_dvfs_opp_table: opp-table-epp {
+		compatible = "operating-points-v2";
+
+		opp-133000000-950 {
+			opp-microvolt = <950000 950000 1300000>;
+			opp-hz = /bits/ 64 <133000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_950>;
+		};
+
+		opp-171000000-1000 {
+			opp-microvolt = <1000000 1000000 1300000>;
+			opp-hz = /bits/ 64 <171000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-247000000-1100 {
+			opp-microvolt = <1100000 1100000 1300000>;
+			opp-hz = /bits/ 64 <247000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1100>;
+		};
+
+		opp-300000000-1200 {
+			opp-microvolt = <1200000 1200000 1300000>;
+			opp-hz = /bits/ 64 <300000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1200>;
+		};
+	};
+
+	gr2d_dvfs_opp_table: opp-table-gr2d {
+		compatible = "operating-points-v2";
+
+		opp-133000000-950 {
+			opp-microvolt = <950000 950000 1300000>;
+			opp-hz = /bits/ 64 <133000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_950>;
+		};
+
+		opp-171000000-1000 {
+			opp-microvolt = <1000000 1000000 1300000>;
+			opp-hz = /bits/ 64 <171000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-247000000-1100 {
+			opp-microvolt = <1100000 1100000 1300000>;
+			opp-hz = /bits/ 64 <247000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1100>;
+		};
+
+		opp-300000000-1200 {
+			opp-microvolt = <1200000 1200000 1300000>;
+			opp-hz = /bits/ 64 <300000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1200>;
+		};
+	};
+
+	gr3d_dvfs_opp_table: opp-table-gr3d {
+		compatible = "operating-points-v2";
+
+		opp-114000000-950 {
+			opp-microvolt = <950000 950000 1300000>;
+			opp-hz = /bits/ 64 <114000000>;
+			opp-supported-hw = <0x0001>;
+			required-opps = <&core_opp_950>;
+		};
+
+		opp-161500000-1000 {
+			opp-microvolt = <1000000 1000000 1300000>;
+			opp-hz = /bits/ 64 <161500000>;
+			opp-supported-hw = <0x0001>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-161500000-950 {
+			opp-microvolt = <950000 950000 1300000>;
+			opp-hz = /bits/ 64 <161500000>;
+			opp-supported-hw = <0x0002>;
+			required-opps = <&core_opp_950>;
+		};
+
+		opp-209000000-1000 {
+			opp-microvolt = <1000000 1000000 1300000>;
+			opp-hz = /bits/ 64 <209000000>;
+			opp-supported-hw = <0x0002>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-218500000-950 {
+			opp-microvolt = <950000 950000 1300000>;
+			opp-hz = /bits/ 64 <218500000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_950>;
+		};
+
+		opp-247000000-1100 {
+			opp-microvolt = <1100000 1100000 1300000>;
+			opp-hz = /bits/ 64 <247000000>;
+			opp-supported-hw = <0x0001>;
+			required-opps = <&core_opp_1100>;
+		};
+
+		opp-247000000-950 {
+			opp-microvolt = <950000 950000 1300000>;
+			opp-hz = /bits/ 64 <247000000>;
+			opp-supported-hw = <0x0008>;
+			required-opps = <&core_opp_950>;
+		};
+
+		opp-256500000-1000 {
+			opp-microvolt = <1000000 1000000 1300000>;
+			opp-hz = /bits/ 64 <256500000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-285000000-1100 {
+			opp-microvolt = <1100000 1100000 1300000>;
+			opp-hz = /bits/ 64 <285000000>;
+			opp-supported-hw = <0x0002>;
+			required-opps = <&core_opp_1100>;
+		};
+
+		opp-285000000-1000 {
+			opp-microvolt = <1000000 1000000 1300000>;
+			opp-hz = /bits/ 64 <285000000>;
+			opp-supported-hw = <0x0008>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-304000000-1200 {
+			opp-microvolt = <1200000 1200000 1300000>;
+			opp-hz = /bits/ 64 <304000000>;
+			opp-supported-hw = <0x0001>;
+			required-opps = <&core_opp_1200>;
+		};
+
+		opp-323000000-1100 {
+			opp-microvolt = <1100000 1100000 1300000>;
+			opp-hz = /bits/ 64 <323000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1100>;
+		};
+
+		opp-333500000-1275 {
+			opp-microvolt = <1275000 1275000 1300000>;
+			opp-hz = /bits/ 64 <333500000>;
+			opp-supported-hw = <0x0001>;
+			required-opps = <&core_opp_1275>;
+		};
+
+		opp-333500000-1200 {
+			opp-microvolt = <1200000 1200000 1300000>;
+			opp-hz = /bits/ 64 <333500000>;
+			opp-supported-hw = <0x0002>;
+			required-opps = <&core_opp_1200>;
+		};
+
+		opp-351500000-1100 {
+			opp-microvolt = <1100000 1100000 1300000>;
+			opp-hz = /bits/ 64 <351500000>;
+			opp-supported-hw = <0x0008>;
+			required-opps = <&core_opp_1100>;
+		};
+
+		opp-361000000-1275 {
+			opp-microvolt = <1275000 1275000 1300000>;
+			opp-hz = /bits/ 64 <361000000>;
+			opp-supported-hw = <0x0002>;
+			required-opps = <&core_opp_1275>;
+		};
+
+		opp-380000000-1200 {
+			opp-microvolt = <1200000 1200000 1300000>;
+			opp-hz = /bits/ 64 <380000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1200>;
+		};
+
+		opp-400000000-1275 {
+			opp-microvolt = <1275000 1275000 1300000>;
+			opp-hz = /bits/ 64 <400000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1275>;
+		};
+
+		opp-400000000-1200 {
+			opp-microvolt = <1200000 1200000 1300000>;
+			opp-hz = /bits/ 64 <400000000>;
+			opp-supported-hw = <0x0008>;
+			required-opps = <&core_opp_1200>;
+		};
+	};
+
+	disp1_dvfs_opp_table: opp-table-disp1 {
+		compatible = "operating-points-v2";
+
+		opp-158000000-950 {
+			opp-microvolt = <950000 950000 1300000>;
+			opp-hz = /bits/ 64 <158000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_950>;
+		};
+
+		opp-190000000-1100 {
+			opp-microvolt = <1100000 1100000 1300000>;
+			opp-hz = /bits/ 64 <190000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1100>;
+		};
+	};
+
+	disp2_dvfs_opp_table: opp-table-disp2 {
+		compatible = "operating-points-v2";
+
+		opp-158000000-950 {
+			opp-microvolt = <950000 950000 1300000>;
+			opp-hz = /bits/ 64 <158000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_950>;
+		};
+
+		opp-190000000-1100 {
+			opp-microvolt = <1100000 1100000 1300000>;
+			opp-hz = /bits/ 64 <190000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1100>;
+		};
+	};
+
+	dsi_dvfs_opp_table: opp-table-dsi {
+		compatible = "operating-points-v2";
+
+		opp-100000000-950 {
+			opp-microvolt = <950000 950000 1300000>;
+			opp-hz = /bits/ 64 <100000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_950>;
+		};
+
+		opp-500000000-1200 {
+			opp-microvolt = <1200000 1200000 1300000>;
+			opp-hz = /bits/ 64 <500000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1200>;
+		};
+	};
+
+	hdmi_dvfs_opp_table: opp-table-hdmi {
+		compatible = "operating-points-v2";
+
+		opp-148500000-1200 {
+			opp-microvolt = <1200000 1200000 1300000>;
+			opp-hz = /bits/ 64 <148500000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1200>;
+		};
+	};
+
+	tvo_dvfs_opp_table: opp-table-tvo {
+		compatible = "operating-points-v2";
+
+		opp-250000000-1200 {
+			opp-microvolt = <1200000 1200000 1300000>;
+			opp-hz = /bits/ 64 <250000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1200>;
+		};
+	};
+
+	sclk_dvfs_opp_table: opp-table-sclk {
+		compatible = "operating-points-v2";
+
+		opp-95000000-950 {
+			opp-microvolt = <950000 950000 1300000>;
+			opp-hz = /bits/ 64 <95000000>;
+			opp-supported-hw = <0x0001>;
+			required-opps = <&core_opp_950>;
+		};
+
+		opp-123500000-950 {
+			opp-microvolt = <950000 950000 1300000>;
+			opp-hz = /bits/ 64 <123500000>;
+			opp-supported-hw = <0x0002>;
+			required-opps = <&core_opp_950>;
+		};
+
+		opp-133000000-1000 {
+			opp-microvolt = <1000000 1000000 1300000>;
+			opp-hz = /bits/ 64 <133000000>;
+			opp-supported-hw = <0x0001>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-152000000-950 {
+			opp-microvolt = <950000 950000 1300000>;
+			opp-hz = /bits/ 64 <152000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_950>;
+		};
+
+		opp-159500000-1000 {
+			opp-microvolt = <1000000 1000000 1300000>;
+			opp-hz = /bits/ 64 <159500000>;
+			opp-supported-hw = <0x0002>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-171000000-950 {
+			opp-microvolt = <950000 950000 1300000>;
+			opp-hz = /bits/ 64 <171000000>;
+			opp-supported-hw = <0x0008>;
+			required-opps = <&core_opp_950>;
+		};
+
+		opp-180500000-1000 {
+			opp-microvolt = <1000000 1000000 1300000>;
+			opp-hz = /bits/ 64 <180500000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-190000000-1100 {
+			opp-microvolt = <1100000 1100000 1300000>;
+			opp-hz = /bits/ 64 <190000000>;
+			opp-supported-hw = <0x0001>;
+			required-opps = <&core_opp_1100>;
+		};
+
+		opp-207000000-1100 {
+			opp-microvolt = <1100000 1100000 1300000>;
+			opp-hz = /bits/ 64 <207000000>;
+			opp-supported-hw = <0x0002>;
+			required-opps = <&core_opp_1100>;
+		};
+
+		opp-218500000-1000 {
+			opp-microvolt = <1000000 1000000 1300000>;
+			opp-hz = /bits/ 64 <218500000>;
+			opp-supported-hw = <0x0008>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-222500000-1200 {
+			opp-microvolt = <1200000 1200000 1300000>;
+			opp-hz = /bits/ 64 <222500000>;
+			opp-supported-hw = <0x0001>;
+			required-opps = <&core_opp_1200>;
+		};
+
+		opp-229500000-1100 {
+			opp-microvolt = <1100000 1100000 1300000>;
+			opp-hz = /bits/ 64 <229500000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1100>;
+		};
+
+		opp-240000000-1225 {
+			opp-microvolt = <1225000 1225000 1300000>;
+			opp-hz = /bits/ 64 <240000000>;
+			opp-supported-hw = <0x0001>;
+			required-opps = <&core_opp_1225>;
+		};
+
+		opp-240000000-1200 {
+			opp-microvolt = <1200000 1200000 1300000>;
+			opp-hz = /bits/ 64 <240000000>;
+			opp-supported-hw = <0x0002>;
+			required-opps = <&core_opp_1200>;
+		};
+
+		opp-247000000-1275 {
+			opp-microvolt = <1275000 1275000 1300000>;
+			opp-hz = /bits/ 64 <247000000>;
+			opp-supported-hw = <0x0001>;
+			required-opps = <&core_opp_1275>;
+		};
+
+		opp-256500000-1100 {
+			opp-microvolt = <1100000 1100000 1300000>;
+			opp-hz = /bits/ 64 <256500000>;
+			opp-supported-hw = <0x0008>;
+			required-opps = <&core_opp_1100>;
+		};
+
+		opp-260000000-1200 {
+			opp-microvolt = <1200000 1200000 1300000>;
+			opp-hz = /bits/ 64 <260000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1200>;
+		};
+
+		opp-262000000-1300 {
+			opp-microvolt = <1300000 1300000 1300000>;
+			opp-hz = /bits/ 64 <262000000>;
+			opp-supported-hw = <0x0001>;
+			required-opps = <&core_opp_1300>;
+		};
+
+		opp-264000000-1275 {
+			opp-microvolt = <1275000 1275000 1300000>;
+			opp-hz = /bits/ 64 <264000000>;
+			opp-supported-hw = <0x0002>;
+			required-opps = <&core_opp_1275>;
+		};
+
+		opp-277500000-1300 {
+			opp-microvolt = <1300000 1300000 1300000>;
+			opp-hz = /bits/ 64 <277500000>;
+			opp-supported-hw = <0x0002>;
+			required-opps = <&core_opp_1300>;
+		};
+
+		opp-285000000-1275 {
+			opp-microvolt = <1275000 1275000 1300000>;
+			opp-hz = /bits/ 64 <285000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1275>;
+		};
+
+		opp-292500000-1200 {
+			opp-microvolt = <1200000 1200000 1300000>;
+			opp-hz = /bits/ 64 <292500000>;
+			opp-supported-hw = <0x0008>;
+			required-opps = <&core_opp_1200>;
+		};
+
+		opp-300000000-1300 {
+			opp-microvolt = <1300000 1300000 1300000>;
+			opp-hz = /bits/ 64 <300000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1300>;
+		};
+
+		opp-300000000-1275 {
+			opp-microvolt = <1275000 1275000 1300000>;
+			opp-hz = /bits/ 64 <300000000>;
+			opp-supported-hw = <0x0008>;
+			required-opps = <&core_opp_1275>;
+		};
+	};
+
+	vde_dvfs_opp_table: opp-table-vde {
+		compatible = "operating-points-v2";
+
+		opp-95000000-950 {
+			opp-microvolt = <950000 950000 1300000>;
+			opp-hz = /bits/ 64 <95000000>;
+			opp-supported-hw = <0x0001>;
+			required-opps = <&core_opp_950>;
+		};
+
+		opp-123500000-1000 {
+			opp-microvolt = <1000000 1000000 1300000>;
+			opp-hz = /bits/ 64 <123500000>;
+			opp-supported-hw = <0x0001>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-123500000-950 {
+			opp-microvolt = <950000 950000 1300000>;
+			opp-hz = /bits/ 64 <123500000>;
+			opp-supported-hw = <0x0002>;
+			required-opps = <&core_opp_950>;
+		};
+
+		opp-152000000-1000 {
+			opp-microvolt = <1000000 1000000 1300000>;
+			opp-hz = /bits/ 64 <152000000>;
+			opp-supported-hw = <0x0002>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-152000000-950 {
+			opp-microvolt = <950000 950000 1300000>;
+			opp-hz = /bits/ 64 <152000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_950>;
+		};
+
+		opp-171000000-950 {
+			opp-microvolt = <950000 950000 1300000>;
+			opp-hz = /bits/ 64 <171000000>;
+			opp-supported-hw = <0x0008>;
+			required-opps = <&core_opp_950>;
+		};
+
+		opp-209000000-1100 {
+			opp-microvolt = <1100000 1100000 1300000>;
+			opp-hz = /bits/ 64 <209000000>;
+			opp-supported-hw = <0x0001>;
+			required-opps = <&core_opp_1100>;
+		};
+
+		opp-209000000-1000 {
+			opp-microvolt = <1000000 1000000 1300000>;
+			opp-hz = /bits/ 64 <209000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-218500000-1000 {
+			opp-microvolt = <1000000 1000000 1300000>;
+			opp-hz = /bits/ 64 <218500000>;
+			opp-supported-hw = <0x0008>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-237500000-1100 {
+			opp-microvolt = <1100000 1100000 1300000>;
+			opp-hz = /bits/ 64 <237500000>;
+			opp-supported-hw = <0x0002>;
+			required-opps = <&core_opp_1100>;
+		};
+
+		opp-275500000-1200 {
+			opp-microvolt = <1200000 1200000 1300000>;
+			opp-hz = /bits/ 64 <275500000>;
+			opp-supported-hw = <0x0001>;
+			required-opps = <&core_opp_1200>;
+		};
+
+		opp-285000000-1100 {
+			opp-microvolt = <1100000 1100000 1300000>;
+			opp-hz = /bits/ 64 <285000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1100>;
+		};
+
+		opp-300000000-1275 {
+			opp-microvolt = <1275000 1275000 1300000>;
+			opp-hz = /bits/ 64 <300000000>;
+			opp-supported-hw = <0x0001>;
+			required-opps = <&core_opp_1275>;
+		};
+
+		opp-300000000-1200 {
+			opp-microvolt = <1200000 1200000 1300000>;
+			opp-hz = /bits/ 64 <300000000>;
+			opp-supported-hw = <0x0006>;
+			required-opps = <&core_opp_1200>;
+		};
+
+		opp-300000000-1100 {
+			opp-microvolt = <1100000 1100000 1300000>;
+			opp-hz = /bits/ 64 <300000000>;
+			opp-supported-hw = <0x0008>;
+			required-opps = <&core_opp_1100>;
+		};
+	};
+
+	ndflash_dvfs_opp_table: opp-table-ndflash {
+		compatible = "operating-points-v2";
+
+		opp-130000000-950 {
+			opp-microvolt = <950000 950000 1300000>;
+			opp-hz = /bits/ 64 <130000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_950>;
+		};
+
+		opp-150000000-1000 {
+			opp-microvolt = <1000000 1000000 1300000>;
+			opp-hz = /bits/ 64 <150000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-158000000-1100 {
+			opp-microvolt = <1100000 1100000 1300000>;
+			opp-hz = /bits/ 64 <158000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1100>;
+		};
+
+		opp-164000000-1200 {
+			opp-microvolt = <1200000 1200000 1300000>;
+			opp-hz = /bits/ 64 <164000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1200>;
+		};
+	};
+
+	nor_dvfs_opp_table: opp-table-nor {
+		compatible = "operating-points-v2";
+
+		opp-92000000-1000 {
+			opp-microvolt = <1000000 1000000 1300000>;
+			opp-hz = /bits/ 64 <92000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1000>;
+		};
+	};
+
+	sdmmc1_dvfs_opp_table: opp-table-sdmmc1 {
+		compatible = "operating-points-v2";
+
+		opp-44000000-950 {
+			opp-microvolt = <950000 950000 1300000>;
+			opp-hz = /bits/ 64 <44000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_950>;
+		};
+
+		opp-52000000-1000 {
+			opp-microvolt = <1000000 1000000 1300000>;
+			opp-hz = /bits/ 64 <52000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1000>;
+		};
+	};
+
+	sdmmc2_dvfs_opp_table: opp-table-sdmmc2 {
+		compatible = "operating-points-v2";
+
+		opp-44000000-950 {
+			opp-microvolt = <950000 950000 1300000>;
+			opp-hz = /bits/ 64 <44000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_950>;
+		};
+
+		opp-52000000-1000 {
+			opp-microvolt = <1000000 1000000 1300000>;
+			opp-hz = /bits/ 64 <52000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1000>;
+		};
+	};
+
+	sdmmc3_dvfs_opp_table: opp-table-sdmmc3 {
+		compatible = "operating-points-v2";
+
+		opp-44000000-950 {
+			opp-microvolt = <950000 950000 1300000>;
+			opp-hz = /bits/ 64 <44000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_950>;
+		};
+
+		opp-52000000-1000 {
+			opp-microvolt = <1000000 1000000 1300000>;
+			opp-hz = /bits/ 64 <52000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1000>;
+		};
+	};
+
+	sdmmc4_dvfs_opp_table: opp-table-sdmmc4 {
+		compatible = "operating-points-v2";
+
+		opp-44000000-950 {
+			opp-microvolt = <950000 950000 1300000>;
+			opp-hz = /bits/ 64 <44000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_950>;
+		};
+
+		opp-52000000-1000 {
+			opp-microvolt = <1000000 1000000 1300000>;
+			opp-hz = /bits/ 64 <52000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1000>;
+		};
+	};
+
+	pcie_dvfs_opp_table: opp-table-pcie {
+		compatible = "operating-points-v2";
+
+		opp-250000000-1200 {
+			opp-microvolt = <1200000 1200000 1300000>;
+			opp-hz = /bits/ 64 <250000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1200>;
+		};
+	};
+
+	usbd_dvfs_opp_table: opp-table-usbd {
+		compatible = "operating-points-v2";
+
+		opp-480000000-1100 {
+			opp-microvolt = <1100000 1100000 1300000>;
+			opp-hz = /bits/ 64 <480000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1100>;
+		};
+	};
+
+	usb2_dvfs_opp_table: opp-table-usb2 {
+		compatible = "operating-points-v2";
+
+		opp-480000000-1100 {
+			opp-microvolt = <1100000 1100000 1300000>;
+			opp-hz = /bits/ 64 <480000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1100>;
+		};
+	};
+
+	usb3_dvfs_opp_table: opp-table-usb3 {
+		compatible = "operating-points-v2";
+
+		opp-480000000-1100 {
+			opp-microvolt = <1100000 1100000 1300000>;
+			opp-hz = /bits/ 64 <480000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1100>;
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/tegra20-plutux.dts b/arch/arm/boot/dts/tegra20-plutux.dts
index 5811b7006a9b..71a8236491df 100644
--- a/arch/arm/boot/dts/tegra20-plutux.dts
+++ b/arch/arm/boot/dts/tegra20-plutux.dts
@@ -60,7 +60,7 @@
 		clock-names = "pll_a", "pll_a_out0", "mclk";
 	};
 
-	vcc_24v_reg: regulator@100 {
+	vcc_24v_reg: regulator-24v0 {
 		compatible = "regulator-fixed";
 		regulator-name = "vcc_24v";
 		regulator-min-microvolt = <24000000>;
@@ -68,7 +68,7 @@
 		regulator-always-on;
 	};
 
-	vdd_5v0_reg: regulator@101 {
+	vdd_5v0_reg: regulator-5v0 {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd_5v0";
 		vin-supply = <&vcc_24v_reg>;
@@ -77,7 +77,7 @@
 		regulator-always-on;
 	};
 
-	vdd_3v3_reg: regulator@102 {
+	vdd_3v3_reg: regulator-3v3 {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd_3v3";
 		vin-supply = <&vcc_24v_reg>;
@@ -86,7 +86,7 @@
 		regulator-always-on;
 	};
 
-	vdd_1v8_reg: regulator@103 {
+	vdd_1v8_reg: regulator-1v8 {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd_1v8";
 		vin-supply = <&vdd_3v3_reg>;
diff --git a/arch/arm/boot/dts/tegra20-seaboard.dts b/arch/arm/boot/dts/tegra20-seaboard.dts
index 92d494b8c3d2..5b4c5ef30996 100644
--- a/arch/arm/boot/dts/tegra20-seaboard.dts
+++ b/arch/arm/boot/dts/tegra20-seaboard.dts
@@ -358,7 +358,7 @@
 		};
 
 		gyrometer@68 {
-			compatible = "invn,mpu3050";
+			compatible = "invensense,mpu3050";
 			reg = <0x68>;
 			interrupt-parent = <&gpio>;
 			interrupts = <TEGRA_GPIO(Z, 4) IRQ_TYPE_LEVEL_HIGH>;
@@ -444,7 +444,7 @@
 					regulator-always-on;
 				};
 
-				sm0 {
+				vdd_core: sm0 {
 					regulator-name = "vdd_sm0,vdd_core";
 					regulator-min-microvolt = <1300000>;
 					regulator-max-microvolt = <1300000>;
@@ -689,6 +689,7 @@
 		nvidia,core-pwr-good-time = <3845 3845>;
 		nvidia,core-pwr-off-time = <3875>;
 		nvidia,sys-clock-req-active-high;
+		core-supply = <&vdd_core>;
 	};
 
 	memory-controller@7000f400 {
@@ -742,8 +743,6 @@
 
 	usb@c5004000 {
 		status = "okay";
-		nvidia,phy-reset-gpio = <&gpio TEGRA_GPIO(V, 1)
-			GPIO_ACTIVE_LOW>;
 	};
 
 	usb-phy@c5004000 {
@@ -792,7 +791,7 @@
 		default-brightness-level = <6>;
 	};
 
-	clk32k_in: clock@0 {
+	clk32k_in: clock-32k {
 		compatible = "fixed-clock";
 		clock-frequency = <32768>;
 		#clock-cells = <0>;
@@ -801,14 +800,14 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		power {
+		key-power {
 			label = "Power";
 			gpios = <&gpio TEGRA_GPIO(V, 2) GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
 			wakeup-source;
 		};
 
-		lid {
+		switch-lid {
 			label = "Lid";
 			gpios = <&gpio TEGRA_GPIO(C, 7) GPIO_ACTIVE_HIGH>;
 			linux,input-type = <5>; /* EV_SW */
@@ -828,7 +827,7 @@
 		ddc-i2c-bus = <&lvds_ddc>;
 	};
 
-	vdd_5v0_reg: regulator@0 {
+	vdd_5v0_reg: regulator-5v0 {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd_5v0";
 		regulator-min-microvolt = <5000000>;
@@ -836,7 +835,7 @@
 		regulator-always-on;
 	};
 
-	regulator@1 {
+	regulator-1v5 {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd_1v5";
 		regulator-min-microvolt = <1500000>;
@@ -844,7 +843,7 @@
 		gpio = <&pmic 0 GPIO_ACTIVE_HIGH>;
 	};
 
-	regulator@2 {
+	regulator-1v2 {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd_1v2";
 		regulator-min-microvolt = <1200000>;
@@ -853,7 +852,7 @@
 		enable-active-high;
 	};
 
-	vbus_reg: regulator@3 {
+	vbus_reg: regulator-vbus {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd_vbus_wup1";
 		regulator-min-microvolt = <5000000>;
@@ -864,7 +863,7 @@
 		regulator-boot-on;
 	};
 
-	vdd_pnl_reg: regulator@4 {
+	vdd_pnl_reg: regulator-pnl {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd_pnl";
 		regulator-min-microvolt = <2800000>;
@@ -873,7 +872,7 @@
 		enable-active-high;
 	};
 
-	vdd_bl_reg: regulator@5 {
+	vdd_bl_reg: regulator-bl {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd_bl";
 		regulator-min-microvolt = <2800000>;
@@ -882,7 +881,7 @@
 		enable-active-high;
 	};
 
-	vdd_hdmi: regulator@6 {
+	vdd_hdmi: regulator-hdmi {
 		compatible = "regulator-fixed";
 		regulator-name = "VDDIO_HDMI";
 		regulator-min-microvolt = <5000000>;
diff --git a/arch/arm/boot/dts/tegra20-tamonten.dtsi b/arch/arm/boot/dts/tegra20-tamonten.dtsi
index dd4d506683de..0e19bd0a847c 100644
--- a/arch/arm/boot/dts/tegra20-tamonten.dtsi
+++ b/arch/arm/boot/dts/tegra20-tamonten.dtsi
@@ -183,8 +183,8 @@
 			};
 			conf_ata {
 				nvidia,pins = "ata", "atb", "atc", "atd", "ate",
-					"cdev1", "cdev2", "dap1", "dtb", "gma",
-					"gmb", "gmc", "gmd", "gme", "gpu7",
+					"cdev1", "cdev2", "dap1", "dtb", "dtf",
+					"gma", "gmb", "gmc", "gmd", "gme", "gpu7",
 					"gpv", "i2cp", "irrx", "irtx", "pta",
 					"rm", "slxa", "slxk", "spia", "spib",
 					"uac";
@@ -203,7 +203,7 @@
 			};
 			conf_crtp {
 				nvidia,pins = "crtp", "dap2", "dap3", "dap4",
-					"dtc", "dte", "dtf", "gpu", "sdio1",
+					"dtc", "dte", "gpu", "sdio1",
 					"slxc", "slxd", "spdi", "spdo", "spig",
 					"uda";
 				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
@@ -357,7 +357,7 @@
 					regulator-always-on;
 				};
 
-				sm0 {
+				vdd_core: sm0 {
 					regulator-name = "vdd_sys_sm0,vdd_core";
 					regulator-min-microvolt = <1200000>;
 					regulator-max-microvolt = <1200000>;
@@ -477,6 +477,7 @@
 		nvidia,core-pwr-good-time = <3845 3845>;
 		nvidia,core-pwr-off-time = <3875>;
 		nvidia,sys-clock-req-active-high;
+		core-supply = <&vdd_core>;
 	};
 
 	pcie@80003000 {
@@ -502,13 +503,13 @@
 		status = "okay";
 	};
 
-	clk32k_in: clock@0 {
+	clk32k_in: clock-32k {
 		compatible = "fixed-clock";
 		clock-frequency = <32768>;
 		#clock-cells = <0>;
 	};
 
-	pci_vdd_reg: regulator@1 {
+	pci_vdd_reg: regulator-1v05 {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd_1v05";
 		regulator-min-microvolt = <1050000>;
diff --git a/arch/arm/boot/dts/tegra20-tec.dts b/arch/arm/boot/dts/tegra20-tec.dts
index 10ff09d86efa..4f41c74384b2 100644
--- a/arch/arm/boot/dts/tegra20-tec.dts
+++ b/arch/arm/boot/dts/tegra20-tec.dts
@@ -69,7 +69,7 @@
 		clock-names = "pll_a", "pll_a_out0", "mclk";
 	};
 
-	vcc_24v_reg: regulator@100 {
+	vcc_24v_reg: regulator-24v {
 		compatible = "regulator-fixed";
 		regulator-name = "vcc_24v";
 		regulator-min-microvolt = <24000000>;
@@ -77,7 +77,7 @@
 		regulator-always-on;
 	};
 
-	vdd_5v0_reg: regulator@101 {
+	vdd_5v0_reg: regulator-5v0 {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd_5v0";
 		vin-supply = <&vcc_24v_reg>;
@@ -86,7 +86,7 @@
 		regulator-always-on;
 	};
 
-	vdd_3v3_reg: regulator@102 {
+	vdd_3v3_reg: regulator-3v3 {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd_3v3";
 		vin-supply = <&vcc_24v_reg>;
@@ -95,7 +95,7 @@
 		regulator-always-on;
 	};
 
-	vdd_1v8_reg: regulator@103 {
+	vdd_1v8_reg: regulator-1v8 {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd_1v8";
 		vin-supply = <&vdd_3v3_reg>;
diff --git a/arch/arm/boot/dts/tegra20-trimslice.dts b/arch/arm/boot/dts/tegra20-trimslice.dts
index 4bc87bc0c2a4..dc51835423a9 100644
--- a/arch/arm/boot/dts/tegra20-trimslice.dts
+++ b/arch/arm/boot/dts/tegra20-trimslice.dts
@@ -287,7 +287,8 @@
 	spi@7000c380 {
 		status = "okay";
 		spi-max-frequency = <48000000>;
-		spi-flash@0 {
+
+		flash@0 {
 			compatible = "winbond,w25q80bl", "jedec,spi-nor";
 			reg = <0>;
 			spi-max-frequency = <48000000>;
@@ -321,6 +322,7 @@
 		nvidia,core-pwr-good-time = <3845 3845>;
 		nvidia,core-pwr-off-time = <3875>;
 		nvidia,sys-clock-req-active-high;
+		core-supply = <&vdd_core>;
 	};
 
 	pcie@80003000 {
@@ -348,8 +350,6 @@
 
 	usb@c5004000 {
 		status = "okay";
-		nvidia,phy-reset-gpio = <&gpio TEGRA_GPIO(V, 0)
-			GPIO_ACTIVE_LOW>;
 	};
 
 	usb-phy@c5004000 {
@@ -379,7 +379,7 @@
 		bus-width = <4>;
 	};
 
-	clk32k_in: clock@0 {
+	clk32k_in: clock-32k {
 		compatible = "fixed-clock";
 		clock-frequency = <32768>;
 		#clock-cells = <0>;
@@ -388,7 +388,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		power {
+		key-power {
 			label = "Power";
 			gpios = <&gpio TEGRA_GPIO(X, 6) GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
@@ -401,7 +401,7 @@
 		gpios = <&gpio TEGRA_GPIO(X, 7) GPIO_ACTIVE_LOW>;
 	};
 
-	hdmi_vdd_reg: regulator@0 {
+	hdmi_vdd_reg: regulator-hdmi {
 		compatible = "regulator-fixed";
 		regulator-name = "avdd_hdmi";
 		regulator-min-microvolt = <3300000>;
@@ -409,7 +409,7 @@
 		regulator-always-on;
 	};
 
-	hdmi_pll_reg: regulator@1 {
+	hdmi_pll_reg: regulator-hdmipll {
 		compatible = "regulator-fixed";
 		regulator-name = "avdd_hdmi_pll";
 		regulator-min-microvolt = <1800000>;
@@ -417,7 +417,7 @@
 		regulator-always-on;
 	};
 
-	vbus_reg: regulator@2 {
+	vbus_reg: regulator-vbus {
 		compatible = "regulator-fixed";
 		regulator-name = "usb1_vbus";
 		regulator-min-microvolt = <5000000>;
@@ -428,7 +428,7 @@
 		regulator-boot-on;
 	};
 
-	pci_clk_reg: regulator@3 {
+	pci_clk_reg: regulator-pciclk {
 		compatible = "regulator-fixed";
 		regulator-name = "pci_clk";
 		regulator-min-microvolt = <3300000>;
@@ -436,7 +436,7 @@
 		regulator-always-on;
 	};
 
-	pci_vdd_reg: regulator@4 {
+	pci_vdd_reg: regulator-pcivdd {
 		compatible = "regulator-fixed";
 		regulator-name = "pci_vdd";
 		regulator-min-microvolt = <1050000>;
@@ -444,6 +444,14 @@
 		regulator-always-on;
 	};
 
+	vdd_core: regulator-core {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_core";
+		regulator-min-microvolt = <1300000>;
+		regulator-max-microvolt = <1300000>;
+		regulator-always-on;
+	};
+
 	sound {
 		compatible = "nvidia,tegra-audio-trimslice";
 		nvidia,i2s-controller = <&tegra_i2s1>;
diff --git a/arch/arm/boot/dts/tegra20-ventana.dts b/arch/arm/boot/dts/tegra20-ventana.dts
index 5a2578b3707f..caa17e876e41 100644
--- a/arch/arm/boot/dts/tegra20-ventana.dts
+++ b/arch/arm/boot/dts/tegra20-ventana.dts
@@ -544,6 +544,7 @@
 		nvidia,core-pwr-good-time = <3845 3845>;
 		nvidia,core-pwr-off-time = <458>;
 		nvidia,sys-clock-req-active-high;
+		core-supply = <&vdd_core>;
 	};
 
 	usb@c5000000 {
@@ -556,8 +557,6 @@
 
 	usb@c5004000 {
 		status = "okay";
-		nvidia,phy-reset-gpio = <&gpio TEGRA_GPIO(V, 1)
-			GPIO_ACTIVE_LOW>;
 	};
 
 	usb-phy@c5004000 {
@@ -606,7 +605,7 @@
 		default-brightness-level = <6>;
 	};
 
-	clk32k_in: clock@0 {
+	clk32k_in: clock-32k {
 		compatible = "fixed-clock";
 		clock-frequency = <32768>;
 		#clock-cells = <0>;
@@ -629,7 +628,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		power {
+		key-power {
 			label = "Power";
 			gpios = <&gpio TEGRA_GPIO(V, 2) GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
@@ -647,7 +646,7 @@
 		ddc-i2c-bus = <&lvds_ddc>;
 	};
 
-	vdd_5v0_reg: regulator@0 {
+	vdd_5v0_reg: regulator-5v0 {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd_5v0";
 		regulator-min-microvolt = <5000000>;
@@ -655,7 +654,7 @@
 		regulator-always-on;
 	};
 
-	regulator@1 {
+	regulator-1v5 {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd_1v5";
 		regulator-min-microvolt = <1500000>;
@@ -663,7 +662,7 @@
 		gpio = <&pmic 0 GPIO_ACTIVE_HIGH>;
 	};
 
-	regulator@2 {
+	regulator-1v2 {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd_1v2";
 		regulator-min-microvolt = <1200000>;
@@ -672,7 +671,7 @@
 		enable-active-high;
 	};
 
-	vdd_pnl_reg: regulator@3 {
+	vdd_pnl_reg: regulator-pnl {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd_pnl";
 		regulator-min-microvolt = <2800000>;
@@ -681,7 +680,7 @@
 		enable-active-high;
 	};
 
-	vdd_bl_reg: regulator@4 {
+	vdd_bl_reg: regulator-bl {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd_bl";
 		regulator-min-microvolt = <2800000>;
diff --git a/arch/arm/boot/dts/tegra20.dtsi b/arch/arm/boot/dts/tegra20.dtsi
index 9508248fd166..62bf0b306472 100644
--- a/arch/arm/boot/dts/tegra20.dtsi
+++ b/arch/arm/boot/dts/tegra20.dtsi
@@ -40,8 +40,10 @@
 		interrupt-names = "syncpt", "host1x";
 		clocks = <&tegra_car TEGRA20_CLK_HOST1X>;
 		clock-names = "host1x";
-		resets = <&tegra_car 28>;
-		reset-names = "host1x";
+		resets = <&tegra_car 28>, <&mc TEGRA20_MC_RESET_HC>;
+		reset-names = "host1x", "mc";
+		power-domains = <&pd_core>;
+		operating-points-v2 = <&host1x_dvfs_opp_table>;
 
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -55,6 +57,9 @@
 			clocks = <&tegra_car TEGRA20_CLK_MPE>;
 			resets = <&tegra_car 60>;
 			reset-names = "mpe";
+			power-domains = <&pd_mpe>;
+			operating-points-v2 = <&mpe_dvfs_opp_table>;
+			status = "disabled";
 		};
 
 		vi@54080000 {
@@ -64,6 +69,9 @@
 			clocks = <&tegra_car TEGRA20_CLK_VI>;
 			resets = <&tegra_car 20>;
 			reset-names = "vi";
+			power-domains = <&pd_venc>;
+			operating-points-v2 = <&vi_dvfs_opp_table>;
+			status = "disabled";
 		};
 
 		epp@540c0000 {
@@ -73,6 +81,9 @@
 			clocks = <&tegra_car TEGRA20_CLK_EPP>;
 			resets = <&tegra_car 19>;
 			reset-names = "epp";
+			power-domains = <&pd_core>;
+			operating-points-v2 = <&epp_dvfs_opp_table>;
+			status = "disabled";
 		};
 
 		isp@54100000 {
@@ -82,6 +93,8 @@
 			clocks = <&tegra_car TEGRA20_CLK_ISP>;
 			resets = <&tegra_car 23>;
 			reset-names = "isp";
+			power-domains = <&pd_venc>;
+			status = "disabled";
 		};
 
 		gr2d@54140000 {
@@ -89,16 +102,20 @@
 			reg = <0x54140000 0x00040000>;
 			interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&tegra_car TEGRA20_CLK_GR2D>;
-			resets = <&tegra_car 21>;
-			reset-names = "2d";
+			resets = <&tegra_car 21>, <&mc TEGRA20_MC_RESET_2D>;
+			reset-names = "2d", "mc";
+			power-domains = <&pd_core>;
+			operating-points-v2 = <&gr2d_dvfs_opp_table>;
 		};
 
 		gr3d@54180000 {
 			compatible = "nvidia,tegra20-gr3d";
 			reg = <0x54180000 0x00040000>;
 			clocks = <&tegra_car TEGRA20_CLK_GR3D>;
-			resets = <&tegra_car 24>;
-			reset-names = "3d";
+			resets = <&tegra_car 24>, <&mc TEGRA20_MC_RESET_3D>;
+			reset-names = "3d", "mc";
+			power-domains = <&pd_3d>;
+			operating-points-v2 = <&gr3d_dvfs_opp_table>;
 		};
 
 		dc@54200000 {
@@ -110,6 +127,8 @@
 			clock-names = "dc", "parent";
 			resets = <&tegra_car 27>;
 			reset-names = "dc";
+			power-domains = <&pd_core>;
+			operating-points-v2 = <&disp1_dvfs_opp_table>;
 
 			nvidia,head = <0>;
 
@@ -138,6 +157,8 @@
 			clock-names = "dc", "parent";
 			resets = <&tegra_car 26>;
 			reset-names = "dc";
+			power-domains = <&pd_core>;
+			operating-points-v2 = <&disp2_dvfs_opp_table>;
 
 			nvidia,head = <1>;
 
@@ -157,7 +178,7 @@
 			};
 		};
 
-		hdmi@54280000 {
+		tegra_hdmi: hdmi@54280000 {
 			compatible = "nvidia,tegra20-hdmi";
 			reg = <0x54280000 0x00040000>;
 			interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
@@ -166,6 +187,9 @@
 			clock-names = "hdmi", "parent";
 			resets = <&tegra_car 51>;
 			reset-names = "hdmi";
+			power-domains = <&pd_core>;
+			operating-points-v2 = <&hdmi_dvfs_opp_table>;
+			#sound-dai-cells = <0>;
 			status = "disabled";
 		};
 
@@ -174,6 +198,8 @@
 			reg = <0x542c0000 0x00040000>;
 			interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&tegra_car TEGRA20_CLK_TVO>;
+			power-domains = <&pd_core>;
+			operating-points-v2 = <&tvo_dvfs_opp_table>;
 			status = "disabled";
 		};
 
@@ -185,6 +211,8 @@
 			clock-names = "dsi", "parent";
 			resets = <&tegra_car 48>;
 			reset-names = "dsi";
+			power-domains = <&pd_core>;
+			operating-points-v2 = <&dsi_dvfs_opp_table>;
 			status = "disabled";
 		};
 	};
@@ -242,6 +270,13 @@
 		reg = <0x60006000 0x1000>;
 		#clock-cells = <1>;
 		#reset-cells = <1>;
+
+		sclk {
+			compatible = "nvidia,tegra20-sclk";
+			clocks = <&tegra_car TEGRA20_CLK_SCLK>;
+			power-domains = <&pd_core>;
+			operating-points-v2 = <&sclk_dvfs_opp_table>;
+		};
 	};
 
 	flow-controller@60007000 {
@@ -293,9 +328,7 @@
 		gpio-controller;
 		#interrupt-cells = <2>;
 		interrupt-controller;
-		/*
 		gpio-ranges = <&pinmux 0 0 224>;
-		*/
 	};
 
 	vde@6001a000 {
@@ -319,6 +352,8 @@
 		clocks = <&tegra_car TEGRA20_CLK_VDE>;
 		reset-names = "vde", "mc";
 		resets = <&tegra_car 61>, <&mc TEGRA20_MC_RESET_VDE>;
+		power-domains = <&pd_vde>;
+		operating-points-v2 = <&vde_dvfs_opp_table>;
 	};
 
 	apbmisc@70000800 {
@@ -352,6 +387,23 @@
 		status = "disabled";
 	};
 
+	tegra_spdif: spdif@70002400 {
+		compatible = "nvidia,tegra20-spdif";
+		reg = <0x70002400 0x200>;
+		interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&tegra_car TEGRA20_CLK_SPDIF_OUT>,
+			 <&tegra_car TEGRA20_CLK_SPDIF_IN>;
+		clock-names = "out", "in";
+		resets = <&tegra_car 10>;
+		dmas = <&apbdma 3>, <&apbdma 3>;
+		dma-names = "rx", "tx";
+		#sound-dai-cells = <0>;
+		status = "disabled";
+
+		assigned-clocks = <&tegra_car TEGRA20_CLK_SPDIF_OUT>;
+		assigned-clock-parents = <&tegra_car TEGRA20_CLK_PLL_A_OUT0>;
+	};
+
 	tegra_i2s1: i2s@70002800 {
 		compatible = "nvidia,tegra20-i2s";
 		reg = <0x70002800 0x200>;
@@ -460,6 +512,8 @@
 		reset-names = "nand";
 		assigned-clocks = <&tegra_car TEGRA20_CLK_NDFLASH>;
 		assigned-clock-rates = <150000000>;
+		power-domains = <&pd_core>;
+		operating-points-v2 = <&ndflash_dvfs_opp_table>;
 		status = "disabled";
 	};
 
@@ -473,6 +527,8 @@
 		clock-names = "gmi";
 		resets = <&tegra_car 42>;
 		reset-names = "gmi";
+		power-domains = <&pd_core>;
+		operating-points-v2 = <&nor_dvfs_opp_table>;
 		status = "disabled";
 	};
 
@@ -523,7 +579,7 @@
 		status = "disabled";
 	};
 
-	i2c@7000c400 {
+	i2c2: i2c@7000c400 {
 		compatible = "nvidia,tegra20-i2c";
 		reg = <0x7000c400 0x100>;
 		interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
@@ -643,6 +699,52 @@
 		clocks = <&tegra_car TEGRA20_CLK_PCLK>, <&clk32k_in>;
 		clock-names = "pclk", "clk32k_in";
 		#clock-cells = <1>;
+
+		pd_core: core-domain {
+			#power-domain-cells = <0>;
+			operating-points-v2 = <&core_opp_table>;
+		};
+
+		powergates {
+			pd_3d: td {
+				clocks = <&tegra_car TEGRA20_CLK_GR3D>;
+				resets = <&mc TEGRA20_MC_RESET_3D>,
+					 <&tegra_car TEGRA20_CLK_GR3D>;
+				power-domains = <&pd_core>;
+				#power-domain-cells = <0>;
+			};
+
+			pd_venc: venc {
+				clocks = <&tegra_car TEGRA20_CLK_ISP>,
+					 <&tegra_car TEGRA20_CLK_VI>,
+					 <&tegra_car TEGRA20_CLK_CSI>;
+				resets = <&mc TEGRA20_MC_RESET_ISP>,
+					 <&mc TEGRA20_MC_RESET_VI>,
+					 <&tegra_car TEGRA20_CLK_ISP>,
+					 <&tegra_car 20 /* VI */>,
+					 <&tegra_car TEGRA20_CLK_CSI>;
+				power-domains = <&pd_core>;
+				#power-domain-cells = <0>;
+			};
+
+			pd_vde: vdec {
+				clocks = <&tegra_car TEGRA20_CLK_VDE>;
+				resets = <&mc TEGRA20_MC_RESET_VDE>,
+					 <&tegra_car TEGRA20_CLK_VDE>;
+				power-domains = <&pd_core>;
+				#power-domain-cells = <0>;
+			};
+
+			pd_mpe: mpe {
+				clocks = <&tegra_car TEGRA20_CLK_MPE>;
+				resets = <&mc TEGRA20_MC_RESET_MPEA>,
+					 <&mc TEGRA20_MC_RESET_MPEB>,
+					 <&mc TEGRA20_MC_RESET_MPEC>,
+					 <&tegra_car TEGRA20_CLK_MPE>;
+				power-domains = <&pd_core>;
+				#power-domain-cells = <0>;
+			};
+		};
 	};
 
 	mc: memory-controller@7000f000 {
@@ -662,12 +764,13 @@
 		reg = <0x7000f400 0x400>;
 		interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&tegra_car TEGRA20_CLK_EMC>;
+		power-domains = <&pd_core>;
 		#address-cells = <1>;
 		#size-cells = <0>;
 		#interconnect-cells = <0>;
 
-		operating-points-v2 = <&emc_icc_dvfs_opp_table>;
 		nvidia,memory-controller = <&mc>;
+		operating-points-v2 = <&emc_icc_dvfs_opp_table>;
 	};
 
 	fuse@7000f800 {
@@ -712,6 +815,9 @@
 			 <&tegra_car 72>,
 			 <&tegra_car 74>;
 		reset-names = "pex", "afi", "pcie_x";
+		power-domains = <&pd_core>;
+		operating-points-v2 = <&pcie_dvfs_opp_table>;
+
 		status = "disabled";
 
 		pci@1,0 {
@@ -753,6 +859,8 @@
 		reset-names = "usb";
 		nvidia,needs-double-reset;
 		nvidia,phy = <&phy1>;
+		power-domains = <&pd_core>;
+		operating-points-v2 = <&usbd_dvfs_opp_table>;
 		status = "disabled";
 	};
 
@@ -792,6 +900,8 @@
 		resets = <&tegra_car 58>;
 		reset-names = "usb";
 		nvidia,phy = <&phy2>;
+		power-domains = <&pd_core>;
+		operating-points-v2 = <&usb2_dvfs_opp_table>;
 		status = "disabled";
 	};
 
@@ -820,6 +930,8 @@
 		resets = <&tegra_car 59>;
 		reset-names = "usb";
 		nvidia,phy = <&phy3>;
+		power-domains = <&pd_core>;
+		operating-points-v2 = <&usb3_dvfs_opp_table>;
 		status = "disabled";
 	};
 
@@ -856,6 +968,8 @@
 		clock-names = "sdhci";
 		resets = <&tegra_car 14>;
 		reset-names = "sdhci";
+		power-domains = <&pd_core>;
+		operating-points-v2 = <&sdmmc1_dvfs_opp_table>;
 		status = "disabled";
 	};
 
@@ -867,6 +981,8 @@
 		clock-names = "sdhci";
 		resets = <&tegra_car 9>;
 		reset-names = "sdhci";
+		power-domains = <&pd_core>;
+		operating-points-v2 = <&sdmmc2_dvfs_opp_table>;
 		status = "disabled";
 	};
 
@@ -878,6 +994,8 @@
 		clock-names = "sdhci";
 		resets = <&tegra_car 69>;
 		reset-names = "sdhci";
+		power-domains = <&pd_core>;
+		operating-points-v2 = <&sdmmc3_dvfs_opp_table>;
 		status = "disabled";
 	};
 
@@ -889,6 +1007,8 @@
 		clock-names = "sdhci";
 		resets = <&tegra_car 15>;
 		reset-names = "sdhci";
+		power-domains = <&pd_core>;
+		operating-points-v2 = <&sdmmc4_dvfs_opp_table>;
 		status = "disabled";
 	};
 
@@ -918,4 +1038,24 @@
 		interrupt-affinity = <&{/cpus/cpu@0}>,
 				     <&{/cpus/cpu@1}>;
 	};
+
+	sound-hdmi {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "NVIDIA Tegra20 HDMI";
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		simple-audio-card,dai-link@0 {
+			reg = <0>;
+
+			cpu {
+				sound-dai = <&tegra_spdif>;
+			};
+
+			codec {
+				sound-dai = <&tegra_hdmi>;
+			};
+		};
+	};
 };
diff --git a/arch/arm/boot/dts/tegra30-apalis-eval.dts b/arch/arm/boot/dts/tegra30-apalis-eval.dts
index 9f653ef41da4..ad968ff968d7 100644
--- a/arch/arm/boot/dts/tegra30-apalis-eval.dts
+++ b/arch/arm/boot/dts/tegra30-apalis-eval.dts
@@ -181,7 +181,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		wakeup {
+		key-wakeup {
 			label = "WAKE1_MICO";
 			gpios = <&gpio TEGRA_GPIO(V, 1) GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_WAKEUP>;
@@ -239,7 +239,7 @@
 
 &gpio {
 	/* Apalis GPIO7 MXM3 pin 15 PLX PEX 8605 PCIe Switch Reset */
-	pex-perst-n {
+	pex-perst-n-hog {
 		gpio-hog;
 		gpios = <TEGRA_GPIO(S, 7) GPIO_ACTIVE_HIGH>;
 		output-high;
diff --git a/arch/arm/boot/dts/tegra30-apalis-v1.1-eval.dts b/arch/arm/boot/dts/tegra30-apalis-v1.1-eval.dts
index 86e138e8c7f0..c172fdb5e1ae 100644
--- a/arch/arm/boot/dts/tegra30-apalis-v1.1-eval.dts
+++ b/arch/arm/boot/dts/tegra30-apalis-v1.1-eval.dts
@@ -182,7 +182,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		wakeup {
+		key-wakeup {
 			label = "WAKE1_MICO";
 			gpios = <&gpio TEGRA_GPIO(V, 1) GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_WAKEUP>;
@@ -257,7 +257,7 @@
 
 &gpio {
 	/* Apalis GPIO7 MXM3 pin 15 PLX PEX 8605 PCIe Switch Reset */
-	pex-perst-n {
+	pex-perst-n-hog {
 		gpio-hog;
 		gpios = <TEGRA_GPIO(S, 7) GPIO_ACTIVE_HIGH>;
 		output-high;
diff --git a/arch/arm/boot/dts/tegra30-apalis-v1.1.dtsi b/arch/arm/boot/dts/tegra30-apalis-v1.1.dtsi
index 6a3a72f81c44..a1bcd67fa505 100644
--- a/arch/arm/boot/dts/tegra30-apalis-v1.1.dtsi
+++ b/arch/arm/boot/dts/tegra30-apalis-v1.1.dtsi
@@ -829,14 +829,17 @@
 
 	serial@70006040 {
 		compatible = "nvidia,tegra30-hsuart";
+		/delete-property/ reg-shift;
 	};
 
 	serial@70006200 {
 		compatible = "nvidia,tegra30-hsuart";
+		/delete-property/ reg-shift;
 	};
 
 	serial@70006300 {
 		compatible = "nvidia,tegra30-hsuart";
+		/delete-property/ reg-shift;
 	};
 
 	hdmi_ddc: i2c@7000c700 {
@@ -990,7 +993,7 @@
 		touchscreen@41 {
 			compatible = "st,stmpe811";
 			reg = <0x41>;
-			irq-gpio = <&gpio TEGRA_GPIO(V, 0) IRQ_TYPE_LEVEL_LOW>;
+			irq-gpio = <&gpio TEGRA_GPIO(V, 0) GPIO_ACTIVE_LOW>;
 			interrupt-controller;
 			id = <0>;
 			blocks = <0x5>;
@@ -1047,9 +1050,6 @@
 			regulator-max-microvolt = <1400000>;
 			regulator-boot-on;
 			regulator-always-on;
-			ti,vsel0-state-low;
-			/* VSEL1: EN_CORE_DVFS_N low for DVFS */
-			ti,vsel1-state-low;
 		};
 	};
 
diff --git a/arch/arm/boot/dts/tegra30-apalis.dtsi b/arch/arm/boot/dts/tegra30-apalis.dtsi
index b2ac51fb15b1..99d7dad72d29 100644
--- a/arch/arm/boot/dts/tegra30-apalis.dtsi
+++ b/arch/arm/boot/dts/tegra30-apalis.dtsi
@@ -820,14 +820,17 @@
 
 	serial@70006040 {
 		compatible = "nvidia,tegra30-hsuart";
+		/delete-property/ reg-shift;
 	};
 
 	serial@70006200 {
 		compatible = "nvidia,tegra30-hsuart";
+		/delete-property/ reg-shift;
 	};
 
 	serial@70006300 {
 		compatible = "nvidia,tegra30-hsuart";
+		/delete-property/ reg-shift;
 	};
 
 	hdmi_ddc: i2c@7000c700 {
@@ -973,7 +976,7 @@
 		touchscreen@41 {
 			compatible = "st,stmpe811";
 			reg = <0x41>;
-			irq-gpio = <&gpio TEGRA_GPIO(V, 0) IRQ_TYPE_LEVEL_LOW>;
+			irq-gpio = <&gpio TEGRA_GPIO(V, 0) GPIO_ACTIVE_LOW>;
 			interrupt-controller;
 			id = <0>;
 			blocks = <0x5>;
@@ -1030,9 +1033,6 @@
 			regulator-max-microvolt = <1400000>;
 			regulator-boot-on;
 			regulator-always-on;
-			ti,vsel0-state-low;
-			/* VSEL1: EN_CORE_DVFS_N low for DVFS */
-			ti,vsel1-state-low;
 		};
 	};
 
diff --git a/arch/arm/boot/dts/tegra30-asus-lvds-display.dtsi b/arch/arm/boot/dts/tegra30-asus-lvds-display.dtsi
new file mode 100644
index 000000000000..a047abfa6369
--- /dev/null
+++ b/arch/arm/boot/dts/tegra30-asus-lvds-display.dtsi
@@ -0,0 +1,61 @@
+// SPDX-License-Identifier: GPL-2.0
+
+/* This dtsi file describes parts common for Asus T30 devices with a LVDS panel. */
+
+/ {
+	host1x@50000000 {
+		lcd: dc@54200000 {
+			rgb {
+				status = "okay";
+
+				port@0 {
+					dpi_output: endpoint {
+						remote-endpoint = <&bridge_input>;
+						bus-width = <24>;
+					};
+				};
+			};
+		};
+	};
+
+	display-panel {
+		power-supply = <&vdd_pnl>;
+		ddc-i2c-bus = <&lcd_ddc>;
+		backlight = <&backlight>;
+
+		port {
+			panel_input: endpoint {
+				remote-endpoint = <&bridge_output>;
+			};
+		};
+	};
+
+	/* Texas Instruments SN75LVDS83B LVDS Transmitter */
+	lvds-encoder {
+		compatible = "ti,sn75lvds83", "lvds-encoder";
+
+		powerdown-gpios = <&gpio TEGRA_GPIO(N, 6) GPIO_ACTIVE_LOW>;
+		power-supply = <&vdd_3v3_sys>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				bridge_input: endpoint {
+					remote-endpoint = <&dpi_output>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				bridge_output: endpoint {
+					remote-endpoint = <&panel_input>;
+				};
+			};
+		};
+	};
+};
diff --git a/arch/arm/boot/dts/tegra30-asus-nexus7-grouper-common.dtsi b/arch/arm/boot/dts/tegra30-asus-nexus7-grouper-common.dtsi
index 07d4ea130964..ee683c5a9c62 100644
--- a/arch/arm/boot/dts/tegra30-asus-nexus7-grouper-common.dtsi
+++ b/arch/arm/boot/dts/tegra30-asus-nexus7-grouper-common.dtsi
@@ -8,6 +8,7 @@
 #include "tegra30.dtsi"
 #include "tegra30-cpu-opp.dtsi"
 #include "tegra30-cpu-opp-microvolt.dtsi"
+#include "tegra30-asus-lvds-display.dtsi"
 
 / {
 	aliases {
@@ -59,25 +60,10 @@
 		};
 	};
 
-	host1x@50000000 {
-		dc@54200000 {
-			rgb {
-				status = "okay";
-
-				port@0 {
-					lcd_output: endpoint {
-						remote-endpoint = <&lvds_encoder_input>;
-						bus-width = <24>;
-					};
-				};
-			};
-		};
-	};
-
 	gpio@6000d000 {
 		init-mode-hog {
 			gpio-hog;
-			gpios =	<TEGRA_GPIO(DD, 7) GPIO_ACTIVE_HIGH>,
+			gpios = <TEGRA_GPIO(DD, 7) GPIO_ACTIVE_HIGH>,
 				<TEGRA_GPIO(CC, 6) GPIO_ACTIVE_HIGH>,
 				<TEGRA_GPIO(R, 0) GPIO_ACTIVE_HIGH>;
 			output-low;
@@ -804,11 +790,13 @@
 
 	uartb: serial@70006040 {
 		compatible = "nvidia,tegra30-hsuart";
+		/delete-property/ reg-shift;
 		/* GPS BCM4751 */
 	};
 
 	uartc: serial@70006200 {
 		compatible = "nvidia,tegra30-hsuart";
+		/delete-property/ reg-shift;
 		status = "okay";
 
 		nvidia,adjust-baud-rates = <0 9600 100>,
@@ -832,7 +820,7 @@
 			vddio-supply = <&vdd_1v8>;
 
 			device-wakeup-gpios = <&gpio TEGRA_GPIO(U, 1) GPIO_ACTIVE_HIGH>;
-			shutdown-gpios =      <&gpio TEGRA_GPIO(U, 0) GPIO_ACTIVE_HIGH>;
+			shutdown-gpios = <&gpio TEGRA_GPIO(U, 0) GPIO_ACTIVE_HIGH>;
 		};
 	};
 
@@ -845,7 +833,7 @@
 		status = "okay";
 
 		touchscreen@10 {
-			compatible ="elan,ektf3624";
+			compatible = "elan,ektf3624";
 			reg = <0x10>;
 
 			interrupt-parent = <&gpio>;
@@ -980,6 +968,7 @@
 		nvidia,core-pwr-off-time = <0>;
 		nvidia,core-power-req-active-high;
 		nvidia,sys-clock-req-active-high;
+		core-supply = <&vdd_core>;
 	};
 
 	ahub@70080000 {
@@ -1069,7 +1058,7 @@
 	};
 
 	/* PMIC has a built-in 32KHz oscillator which is used by PMC */
-	clk32k_in: clock@0 {
+	clk32k_in: clock-32k {
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
 		clock-frequency = <32768>;
@@ -1114,20 +1103,14 @@
 		 */
 		compatible = "panel-lvds";
 
-		power-supply = <&vdd_pnl>;
-		backlight = <&backlight>;
-
 		width-mm = <94>;
 		height-mm = <150>;
 		rotation = <180>;
 
 		data-mapping = "jeida-24";
 
-		port {
-			panel_input: endpoint {
-				remote-endpoint = <&lvds_encoder_output>;
-			};
-		};
+		/* DDC unconnected on Nexus 7 */
+		/delete-property/ ddc-i2c-bus;
 	};
 
 	firmware {
@@ -1141,7 +1124,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		hall-sensor {
+		switch-hall-sensor {
 			label = "Lid";
 			gpios = <&gpio TEGRA_GPIO(S, 6) GPIO_ACTIVE_LOW>;
 			linux,input-type = <EV_SW>;
@@ -1151,7 +1134,7 @@
 			wakeup-source;
 		};
 
-		power {
+		key-power {
 			label = "Power";
 			gpios = <&gpio TEGRA_GPIO(V, 0) GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
@@ -1160,7 +1143,7 @@
 			wakeup-source;
 		};
 
-		volume-up {
+		key-volume-up {
 			label = "Volume Up";
 			gpios = <&gpio TEGRA_GPIO(Q, 2) GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_VOLUMEUP>;
@@ -1169,7 +1152,7 @@
 			wakeup-source;
 		};
 
-		volume-down {
+		key-volume-down {
 			label = "Volume Down";
 			gpios = <&gpio TEGRA_GPIO(Q, 3) GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_VOLUMEDOWN>;
@@ -1179,35 +1162,7 @@
 		};
 	};
 
-	lvds-encoder {
-		compatible = "ti,sn75lvds83", "lvds-encoder";
-
-		powerdown-gpios = <&gpio TEGRA_GPIO(N, 6) GPIO_ACTIVE_LOW>;
-		power-supply = <&vdd_3v3_sys>;
-
-		ports {
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			port@0 {
-				reg = <0>;
-
-				lvds_encoder_input: endpoint {
-					remote-endpoint = <&lcd_output>;
-				};
-			};
-
-			port@1 {
-				reg = <1>;
-
-				lvds_encoder_output: endpoint {
-					remote-endpoint = <&panel_input>;
-				};
-			};
-		};
-	};
-
-	vdd_5v0_sys: regulator@0 {
+	vdd_5v0_sys: regulator-5v0 {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd_5v0";
 		regulator-min-microvolt = <5000000>;
@@ -1216,7 +1171,7 @@
 		regulator-boot-on;
 	};
 
-	vdd_3v3_sys: regulator@1 {
+	vdd_3v3_sys: regulator-3v3 {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd_3v3";
 		regulator-min-microvolt = <3300000>;
@@ -1226,7 +1181,7 @@
 		vin-supply = <&vdd_5v0_sys>;
 	};
 
-	vdd_pnl: regulator@2 {
+	vdd_pnl: regulator-panel {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd_panel";
 		regulator-min-microvolt = <3300000>;
@@ -1237,7 +1192,7 @@
 		vin-supply = <&vdd_3v3_sys>;
 	};
 
-	vcc_3v3_ts: regulator@3 {
+	vcc_3v3_ts: regulator-ts {
 		compatible = "regulator-fixed";
 		regulator-name = "ldo_s-1167_3v3";
 		regulator-min-microvolt = <3300000>;
diff --git a/arch/arm/boot/dts/tegra30-asus-nexus7-grouper-maxim-pmic.dtsi b/arch/arm/boot/dts/tegra30-asus-nexus7-grouper-maxim-pmic.dtsi
index 53966fa4eef2..cd28e8782f7d 100644
--- a/arch/arm/boot/dts/tegra30-asus-nexus7-grouper-maxim-pmic.dtsi
+++ b/arch/arm/boot/dts/tegra30-asus-nexus7-grouper-maxim-pmic.dtsi
@@ -166,12 +166,12 @@
 		};
 	};
 
-	vdd_3v3_sys: regulator@1 {
+	vdd_3v3_sys: regulator-3v3 {
 		gpio = <&pmic 3 GPIO_ACTIVE_HIGH>;
 		enable-active-high;
 	};
 
-	regulator@4 {
+	regulator-usb {
 		compatible = "regulator-fixed";
 		regulator-name = "avdd_usb";
 		regulator-min-microvolt = <3300000>;
diff --git a/arch/arm/boot/dts/tegra30-asus-nexus7-grouper-memory-timings.dtsi b/arch/arm/boot/dts/tegra30-asus-nexus7-grouper-memory-timings.dtsi
index bcff0997ee51..6c229e1d67e7 100644
--- a/arch/arm/boot/dts/tegra30-asus-nexus7-grouper-memory-timings.dtsi
+++ b/arch/arm/boot/dts/tegra30-asus-nexus7-grouper-memory-timings.dtsi
@@ -1565,13 +1565,13 @@
 };
 
 &emc_icc_dvfs_opp_table {
-	/delete-node/ opp@750000000,1300;
-	/delete-node/ opp@800000000,1300;
-	/delete-node/ opp@900000000,1350;
+	/delete-node/ opp-750000000-1300;
+	/delete-node/ opp-800000000-1300;
+	/delete-node/ opp-900000000-1350;
 };
 
 &emc_bw_dfs_opp_table {
-	/delete-node/ opp@750000000;
-	/delete-node/ opp@800000000;
-	/delete-node/ opp@900000000;
+	/delete-node/ opp-750000000;
+	/delete-node/ opp-800000000;
+	/delete-node/ opp-900000000;
 };
diff --git a/arch/arm/boot/dts/tegra30-asus-nexus7-grouper-ti-pmic.dtsi b/arch/arm/boot/dts/tegra30-asus-nexus7-grouper-ti-pmic.dtsi
index 9365ae607239..ee4a3f482769 100644
--- a/arch/arm/boot/dts/tegra30-asus-nexus7-grouper-ti-pmic.dtsi
+++ b/arch/arm/boot/dts/tegra30-asus-nexus7-grouper-ti-pmic.dtsi
@@ -143,7 +143,7 @@
 		};
 	};
 
-	vdd_3v3_sys: regulator@1 {
+	vdd_3v3_sys: regulator-3v3 {
 		gpio = <&pmic 6 GPIO_ACTIVE_HIGH>;
 		enable-active-high;
 	};
diff --git a/arch/arm/boot/dts/tegra30-asus-nexus7-grouper.dtsi b/arch/arm/boot/dts/tegra30-asus-nexus7-grouper.dtsi
index a044dbd200a9..564cfcde21a9 100644
--- a/arch/arm/boot/dts/tegra30-asus-nexus7-grouper.dtsi
+++ b/arch/arm/boot/dts/tegra30-asus-nexus7-grouper.dtsi
@@ -137,7 +137,6 @@
 		nfc@28 {
 			compatible = "nxp,pn544-i2c";
 			reg = <0x28>;
-			clock-frequency = <100000>;
 
 			interrupt-parent = <&gpio>;
 			interrupts = <TEGRA_GPIO(X, 0) IRQ_TYPE_EDGE_RISING>;
diff --git a/arch/arm/boot/dts/tegra30-asus-nexus7-tilapia.dtsi b/arch/arm/boot/dts/tegra30-asus-nexus7-tilapia.dtsi
index a681ad51fddd..1b241f0542b8 100644
--- a/arch/arm/boot/dts/tegra30-asus-nexus7-tilapia.dtsi
+++ b/arch/arm/boot/dts/tegra30-asus-nexus7-tilapia.dtsi
@@ -25,7 +25,7 @@
 	gpio@6000d000 {
 		init-mode-3g-hog {
 			gpio-hog;
-			gpios =	<TEGRA_GPIO(D, 2) GPIO_ACTIVE_HIGH>,
+			gpios = <TEGRA_GPIO(D, 2) GPIO_ACTIVE_HIGH>,
 				<TEGRA_GPIO(C, 6) GPIO_ACTIVE_HIGH>,
 				<TEGRA_GPIO(W, 3) GPIO_ACTIVE_HIGH>,
 				<TEGRA_GPIO(P, 1) GPIO_ACTIVE_HIGH>,
@@ -223,8 +223,6 @@
 			compatible = "nxp,pn544-i2c";
 			reg = <0x2a>;
 
-			clock-frequency = <100000>;
-
 			interrupt-parent = <&gpio>;
 			interrupts = <TEGRA_GPIO(S, 7) IRQ_TYPE_EDGE_RISING>;
 
diff --git a/arch/arm/boot/dts/tegra30-asus-tf201.dts b/arch/arm/boot/dts/tegra30-asus-tf201.dts
new file mode 100644
index 000000000000..315c6dc068c5
--- /dev/null
+++ b/arch/arm/boot/dts/tegra30-asus-tf201.dts
@@ -0,0 +1,627 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include "tegra30-asus-transformer-common.dtsi"
+#include "tegra30-asus-lvds-display.dtsi"
+
+/ {
+	model = "Asus Transformer Prime TF201";
+	compatible = "asus,tf201", "nvidia,tegra30";
+
+	pinmux@70000868 {
+		state_default: pinmux {
+			lcd_pwr2_pc6 {
+				nvidia,pins = "lcd_pwr2_pc6",
+						"lcd_dc1_pd2";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			pbb3 {
+				nvidia,pins = "pbb3";
+				nvidia,function = "vgp3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			pbb7 {
+				nvidia,pins = "pbb7";
+				nvidia,function = "i2s4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			kb_row7_pr7 {
+				nvidia,pins = "kb_row7_pr7";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			gmi_cs4_n_pk2 {
+				nvidia,pins = "gmi_cs4_n_pk2";
+				nvidia,function = "gmi";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+		};
+	};
+
+	serial@70006200 {
+		/* Azurewave AW-NH615 BCM4329B1 */
+		bluetooth {
+			compatible = "brcm,bcm4329-bt";
+		};
+	};
+
+	i2c@7000c400 {
+		/* Atmel MXT768E touchscreen */
+		touchscreen@4d {
+			compatible = "atmel,maxtouch";
+			reg = <0x4d>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(H, 4) IRQ_TYPE_EDGE_FALLING>;
+			reset-gpios = <&gpio TEGRA_GPIO(H, 6) GPIO_ACTIVE_LOW>;
+
+			vdda-supply = <&vdd_3v3_sys>;
+			vdd-supply  = <&vdd_3v3_sys>;
+		};
+	};
+
+	i2c@7000c500 {
+		clock-frequency = <100000>;
+
+		magnetometer@e {
+			mount-matrix =  "-1",  "0",  "0",
+					 "0", "-1",  "0",
+					 "0",  "0", "-1";
+		};
+
+		gyroscope@68 {
+			mount-matrix =   "0", "-1",  "0",
+					"-1",  "0",  "0",
+					 "0",  "0", "-1";
+
+			/* External I2C interface */
+			i2c-gate {
+				accelerometer@f {
+					mount-matrix =   "1",  "0",  "0",
+							 "0", "-1",  "0",
+							 "0",  "0",  "1";
+				};
+			};
+		};
+	};
+
+	i2c@7000d000 {
+		/* Realtek ALC5631 audio codec */
+		rt5631: audio-codec@1a {
+			compatible = "realtek,rt5631";
+			reg = <0x1a>;
+		};
+	};
+
+	memory-controller@7000f000 {
+		emc-timings-0 {
+			/* Elpida 1GB EDB8132B2MA-8D-F LPDDR2 400MHz */
+			nvidia,ram-code = <0>;
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+
+				nvidia,emem-configuration = < 0x00020001 0x80000010
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000003 0x00000001 0x00000002 0x00000004
+					0x00000001 0x00000000 0x00000002 0x00000002
+					0x02020001 0x00060402 0x73e30303 0x001f0000 >;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+
+				nvidia,emem-configuration = < 0x00010001 0x80000010
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000003 0x00000001 0x00000002 0x00000004
+					0x00000001 0x00000000 0x00000002 0x00000002
+					0x02020001 0x00060402 0x72c30303 0x001f0000 >;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emem-configuration = < 0x00000001 0x80000018
+					0x00000001 0x00000001 0x00000003 0x00000001
+					0x00000003 0x00000001 0x00000002 0x00000004
+					0x00000001 0x00000000 0x00000002 0x00000002
+					0x02020001 0x00060403 0x72430504 0x001f0000 >;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emem-configuration = < 0x00000003 0x80000025
+					0x00000001 0x00000001 0x00000006 0x00000003
+					0x00000005 0x00000001 0x00000002 0x00000004
+					0x00000001 0x00000000 0x00000003 0x00000002
+					0x02030001 0x00070506 0x71e40a07 0x001f0000 >;
+			};
+
+			timing-400000000 {
+				clock-frequency = <400000000>;
+
+				nvidia,emem-configuration = < 0x00000006 0x80000048
+					0x00000002 0x00000003 0x0000000c 0x00000007
+					0x00000009 0x00000001 0x00000002 0x00000006
+					0x00000001 0x00000000 0x00000004 0x00000004
+					0x04040001 0x000d090c 0x71c6120d 0x001f0000 >;
+			};
+		};
+
+		emc-timings-1 {
+			/* TF201 Unknown 1GB LPDDR2 500MHZ */
+			nvidia,ram-code = <1>;
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+
+				nvidia,emem-configuration = < 0x00020001 0x80000010
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000003 0x00000001 0x00000002 0x00000004
+					0x00000001 0x00000000 0x00000002 0x00000002
+					0x02020001 0x00060402 0x73e30303 0x001f0000 >;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+
+				nvidia,emem-configuration = < 0x00010001 0x80000010
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000003 0x00000001 0x00000002 0x00000004
+					0x00000001 0x00000000 0x00000002 0x00000002
+					0x02020001 0x00060402 0x72c30303 0x001f0000 >;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emem-configuration = < 0x00000001 0x80000018
+					0x00000001 0x00000001 0x00000003 0x00000001
+					0x00000003 0x00000001 0x00000002 0x00000004
+					0x00000001 0x00000000 0x00000002 0x00000002
+					0x02020001 0x00060403 0x72430504 0x001f0000 >;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emem-configuration = < 0x00000003 0x80000025
+					0x00000001 0x00000001 0x00000006 0x00000003
+					0x00000005 0x00000001 0x00000002 0x00000004
+					0x00000001 0x00000000 0x00000003 0x00000002
+					0x02030001 0x00070506 0x71e40a07 0x001f0000 >;
+			};
+
+			timing-500000000 {
+				clock-frequency = <500000000>;
+
+				nvidia,emem-configuration = < 0x00000007 0x8000005a
+					0x00000003 0x00000004 0x0000000e 0x00000009
+					0x0000000c 0x00000002 0x00000002 0x00000008
+					0x00000001 0x00000000 0x00000004 0x00000005
+					0x05040001 0x00100a0e 0x71c8170f 0x001f0000 >;
+			};
+		};
+	};
+
+	memory-controller@7000f400 {
+		emc-timings-0 {
+			/* Elpida 1GB EDB8132B2MA-8D-F LPDDR2 400MHz */
+			nvidia,ram-code = <0>;
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x00010022>;
+				nvidia,emc-mode-2 = <0x00020001>;
+				nvidia,emc-mode-reset = <0x00000000>;
+				nvidia,emc-zcal-cnt-long = <0x00000009>;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000001
+					0x00000003 0x00000002 0x00000002 0x00000004
+					0x00000004 0x00000001 0x00000005 0x00000002
+					0x00000002 0x00000001 0x00000001 0x00000000
+					0x00000001 0x00000003 0x00000001 0x0000000b
+					0x0000000a 0x00000060 0x00000000 0x00000018
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000007 0x00000004 0x00000004
+					0x00000003 0x00000008 0x00000004 0x00000004
+					0x00000002 0x0000006b 0x00000004 0x00000004
+					0x00000000 0x00000000 0x00004282 0x00780084
+					0x00008000 0x00098000 0x00098000 0x00098000
+					0x00098000 0x00000010 0x00000010 0x00000010
+					0x00000010 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000008 0x00000008 0x00000008
+					0x00000008 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x00100220 0x0800201c 0x00000000
+					0x77ffc004 0x01f1f008 0x00000000 0x00000007
+					0x08000068 0x08000000 0x00000802 0x00000000
+					0x00000009 0x00090009 0xa0f10000 0x00000000
+					0x00000000 0x800001c5 0xe0000000 0xff00ff00 >;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x00010022>;
+				nvidia,emc-mode-2 = <0x00020001>;
+				nvidia,emc-mode-reset = <0x00000000>;
+				nvidia,emc-zcal-cnt-long = <0x00000009>;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000003
+					0x00000006 0x00000002 0x00000002 0x00000004
+					0x00000004 0x00000001 0x00000005 0x00000002
+					0x00000002 0x00000001 0x00000001 0x00000000
+					0x00000001 0x00000003 0x00000001 0x0000000b
+					0x0000000a 0x000000c0 0x00000000 0x00000030
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000007 0x00000008 0x00000008
+					0x00000003 0x00000008 0x00000004 0x00000004
+					0x00000002 0x000000d5 0x00000004 0x00000004
+					0x00000000 0x00000000 0x00004282 0x00780084
+					0x00008000 0x00098000 0x00098000 0x00098000
+					0x00098000 0x00000010 0x00000010 0x00000010
+					0x00000010 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000018 0x00000018 0x00000018
+					0x00000018 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x00100220 0x0800201c 0x00000000
+					0x77ffc004 0x01f1f008 0x00000000 0x00000007
+					0x08000068 0x08000000 0x00000802 0x00000000
+					0x00000009 0x00090009 0xa0f10000 0x00000000
+					0x00000000 0x80000287 0xe0000000 0xff00ff00 >;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x00010022>;
+				nvidia,emc-mode-2 = <0x00020001>;
+				nvidia,emc-mode-reset = <0x00000000>;
+				nvidia,emc-zcal-cnt-long = <0x0000000a>;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000006
+					0x0000000d 0x00000004 0x00000002 0x00000004
+					0x00000004 0x00000001 0x00000005 0x00000002
+					0x00000002 0x00000001 0x00000001 0x00000000
+					0x00000001 0x00000003 0x00000001 0x0000000b
+					0x0000000a 0x00000181 0x00000000 0x00000060
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000007 0x0000000f 0x0000000f
+					0x00000003 0x00000008 0x00000004 0x00000004
+					0x00000002 0x000001a9 0x00000004 0x00000006
+					0x00000000 0x00000000 0x00004282 0x00780084
+					0x00008000 0x000a0000 0x000a0000 0x000a0000
+					0x000a0000 0x00000010 0x00000010 0x00000010
+					0x00000010 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000008 0x00000008 0x00000008
+					0x00000008 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x00120220 0x0800201c 0x00000000
+					0x77ffc004 0x01f1f008 0x00000000 0x00000007
+					0x08000068 0x08000000 0x00000802 0x00000000
+					0x0000000a 0x00090009 0xa0f10000 0x00000000
+					0x00000000 0x8000040b 0xe0000000 0xff00ff00 >;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x00010042>;
+				nvidia,emc-mode-2 = <0x00020001>;
+				nvidia,emc-mode-reset = <0x00000000>;
+				nvidia,emc-zcal-cnt-long = <0x00000013>;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x0000000c
+					0x0000001a 0x00000008 0x00000003 0x00000005
+					0x00000004 0x00000001 0x00000006 0x00000003
+					0x00000003 0x00000002 0x00000002 0x00000000
+					0x00000001 0x00000003 0x00000001 0x0000000c
+					0x0000000a 0x00000303 0x00000000 0x000000c0
+					0x00000001 0x00000001 0x00000003 0x00000000
+					0x00000001 0x00000007 0x0000001d 0x0000001d
+					0x00000004 0x0000000b 0x00000005 0x00000004
+					0x00000002 0x00000351 0x00000004 0x00000006
+					0x00000000 0x00000000 0x00004282 0x00440084
+					0x00008000 0x00074000 0x00074000 0x00074000
+					0x00074000 0x00000010 0x00000010 0x00000010
+					0x00000010 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000018 0x00000018 0x00000018
+					0x00000018 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00078000 0x00078000 0x00078000
+					0x00078000 0x00100220 0x0800201c 0x00000000
+					0x77ffc004 0x01f1f008 0x00000000 0x00000007
+					0x08000068 0x08000000 0x00000802 0x00000000
+					0x00000013 0x00090009 0xa0f10000 0x00000000
+					0x00000000 0x80000713 0xe0000000 0xff00ff00 >;
+			};
+
+			timing-400000000 {
+				clock-frequency = <400000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x00010082>;
+				nvidia,emc-mode-2 = <0x00020004>;
+				nvidia,emc-mode-reset = <0x00000000>;
+				nvidia,emc-zcal-cnt-long = <0x00000024>;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000017
+					0x00000033 0x00000010 0x00000007 0x00000007
+					0x00000007 0x00000002 0x0000000a 0x00000007
+					0x00000007 0x00000003 0x00000002 0x00000000
+					0x00000003 0x00000007 0x00000004 0x0000000d
+					0x0000000e 0x000005e9 0x00000000 0x0000017a
+					0x00000002 0x00000002 0x00000007 0x00000000
+					0x00000001 0x0000000c 0x00000038 0x00000038
+					0x00000006 0x00000014 0x00000009 0x00000004
+					0x00000002 0x00000680 0x00000000 0x00000006
+					0x00000000 0x00000000 0x00006282 0x001d0084
+					0x00008000 0x0002c000 0x0002c000 0x0002c000
+					0x0002c000 0x00000010 0x00000010 0x00000010
+					0x00000010 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000008 0x00000008 0x00000008
+					0x00000008 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00048000 0x00048000 0x00048000
+					0x00048000 0x000c0220 0x0800003d 0x00000000
+					0x77ffc004 0x01f1f408 0x00000000 0x00000007
+					0x08000068 0x08000000 0x00000802 0x00000000
+					0x00000024 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x80000ce6 0xe0000000 0xff00ff88 >;
+			};
+		};
+
+		emc-timings-1 {
+			/* TF201 Unknown 1GB LPDDR2 500MHZ */
+			nvidia,ram-code = <1>;
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x00010022>;
+				nvidia,emc-mode-2 = <0x00020001>;
+				nvidia,emc-mode-reset = <0x00000000>;
+				nvidia,emc-zcal-cnt-long = <0x00000009>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000001
+					0x00000003 0x00000002 0x00000002 0x00000004
+					0x00000004 0x00000001 0x00000005 0x00000002
+					0x00000002 0x00000001 0x00000001 0x00000000
+					0x00000001 0x00000003 0x00000001 0x0000000b
+					0x00000009 0x00000060 0x00000000 0x00000018
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000007 0x00000004 0x00000004
+					0x00000003 0x00000008 0x00000004 0x00000004
+					0x00000002 0x0000006b 0x00000004 0x00000004
+					0x00000000 0x00000000 0x00004282 0x00780084
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00100220 0x0800201c 0x00000000
+					0x77ffc004 0x01f1f008 0x00000000 0x00000007
+					0x08000068 0x08000000 0x00000802 0x00064000
+					0x0000000a 0x00090009 0xa0f10000 0x00000000
+					0x00000000 0x800001c5 0xe0000000 0xff00ff00 >;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x00010022>;
+				nvidia,emc-mode-2 = <0x00020001>;
+				nvidia,emc-mode-reset = <0x00000000>;
+				nvidia,emc-zcal-cnt-long = <0x00000009>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000003
+					0x00000006 0x00000002 0x00000002 0x00000004
+					0x00000004 0x00000001 0x00000005 0x00000002
+					0x00000002 0x00000001 0x00000001 0x00000000
+					0x00000001 0x00000003 0x00000001 0x0000000b
+					0x00000009 0x000000c0 0x00000000 0x00000030
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000007 0x00000008 0x00000008
+					0x00000003 0x00000008 0x00000004 0x00000004
+					0x00000002 0x000000d5 0x00000004 0x00000004
+					0x00000000 0x00000000 0x00004282 0x00780084
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00100220 0x0800201c 0x00000000
+					0x77ffc004 0x01f1f008 0x00000000 0x00000007
+					0x08000068 0x08000000 0x00000802 0x00064000
+					0x00000013 0x00090009 0xa0f10000 0x00000000
+					0x00000000 0x80000287 0xe0000000 0xff00ff00 >;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x00010022>;
+				nvidia,emc-mode-2 = <0x00020001>;
+				nvidia,emc-mode-reset = <0x00000000>;
+				nvidia,emc-zcal-cnt-long = <0x0000000a>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000006
+					0x0000000d 0x00000004 0x00000002 0x00000004
+					0x00000004 0x00000001 0x00000005 0x00000002
+					0x00000002 0x00000001 0x00000001 0x00000000
+					0x00000001 0x00000003 0x00000001 0x0000000b
+					0x00000009 0x00000181 0x00000000 0x00000060
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000007 0x0000000f 0x0000000f
+					0x00000003 0x00000008 0x00000004 0x00000004
+					0x00000002 0x000001a9 0x00000004 0x00000004
+					0x00000000 0x00000000 0x00004282 0x00780084
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00100220 0x0800201c 0x00000000
+					0x77ffc004 0x01f1f008 0x00000000 0x00000007
+					0x08000068 0x08000000 0x00000802 0x00064000
+					0x00000025 0x00090009 0xa0f10000 0x00000000
+					0x00000000 0x8000040b 0xe0000000 0xff00ff00 >;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x00010042>;
+				nvidia,emc-mode-2 = <0x00020001>;
+				nvidia,emc-mode-reset = <0x00000000>;
+				nvidia,emc-zcal-cnt-long = <0x00000013>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x0000000c
+					0x0000001a 0x00000008 0x00000003 0x00000005
+					0x00000004 0x00000001 0x00000006 0x00000003
+					0x00000003 0x00000002 0x00000002 0x00000000
+					0x00000001 0x00000003 0x00000001 0x0000000c
+					0x0000000a 0x00000303 0x00000000 0x000000c0
+					0x00000001 0x00000001 0x00000003 0x00000000
+					0x00000001 0x00000007 0x0000001d 0x0000001d
+					0x00000004 0x0000000b 0x00000005 0x00000004
+					0x00000002 0x00000351 0x00000004 0x00000006
+					0x00000000 0x00000000 0x00004282 0x00440084
+					0x00008000 0x00060000 0x00060000 0x00060000
+					0x00060000 0x00072000 0x00072000 0x00072000
+					0x00072000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000d0000 0x000d0000 0x000d0000
+					0x000d0000 0x000e0220 0x0800201c 0x00000000
+					0x77ffc004 0x01f1f008 0x00000000 0x00000007
+					0x08000068 0x08000000 0x00000802 0x00064000
+					0x0000004a 0x00090009 0xa0f10000 0x00000000
+					0x00000000 0x80000713 0xe0000000 0xff00ff00 >;
+			};
+
+			timing-500000000 {
+				clock-frequency = <500000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x000100c2>;
+				nvidia,emc-mode-2 = <0x00020005>;
+				nvidia,emc-mode-reset = <0x00000000>;
+				nvidia,emc-zcal-cnt-long = <0x0000002d>;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x0000001d
+					0x00000040 0x00000014 0x00000008 0x00000007
+					0x00000009 0x00000003 0x0000000d 0x00000008
+					0x00000008 0x00000004 0x00000002 0x00000000
+					0x00000004 0x00000008 0x00000005 0x0000000d
+					0x0000000f 0x00000763 0x00000000 0x000001d8
+					0x00000003 0x00000003 0x00000008 0x00000000
+					0x00000001 0x0000000e 0x00000046 0x00000046
+					0x00000008 0x00000019 0x0000000b 0x00000004
+					0x00000002 0x00000820 0x00000000 0x00000006
+					0x00000000 0x00000000 0x00006282 0xf0140091
+					0x00008000 0x00000008 0x00000008 0x00000008
+					0x00000008 0x0000000a 0x0000000a 0x0000000a
+					0x0000000a 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x0000000c 0x0000000c 0x0000000c
+					0x0000000c 0x00080220 0x0800003d 0x00000000
+					0x77ffc004 0x01f1f408 0x00000000 0x00000007
+					0x08000068 0x08000000 0x00000802 0x00064000
+					0x000000b4 0x000d000d 0xa0f10404 0x00000000
+					0x00000000 0x80000fde 0xe0000000 0xff00ff88 >;
+			};
+		};
+	};
+
+	usb-phy@7d000000 {
+		/delete-property/ nvidia,xcvr-setup-use-fuses;
+		nvidia,xcvr-setup = <5>;      /* Based on TF201 fuse value - 48 */
+	};
+
+	usb-phy@7d008000 {
+		/delete-property/ nvidia,xcvr-setup-use-fuses;
+		nvidia,xcvr-setup = <5>;      /* Based on TF201 fuse value - 48 */
+	};
+
+	display-panel {
+		compatible = "hannstar,hsd101pww2";
+	};
+
+	haptic-feedback {
+		compatible = "gpio-vibrator";
+		enable-gpios = <&gpio TEGRA_GPIO(H, 7) GPIO_ACTIVE_HIGH>;
+		vcc-supply = <&vdd_3v3_sys>;
+	};
+};
+
+&emc_icc_dvfs_opp_table {
+	/delete-node/ opp-533000000-1200;
+	/delete-node/ opp-625000000-1200;
+	/delete-node/ opp-625000000-1250;
+	/delete-node/ opp-667000000-1200;
+	/delete-node/ opp-750000000-1300;
+	/delete-node/ opp-800000000-1300;
+	/delete-node/ opp-900000000-1350;
+};
+
+&emc_bw_dfs_opp_table {
+	/delete-node/ opp-533000000;
+	/delete-node/ opp-625000000;
+	/delete-node/ opp-667000000;
+	/delete-node/ opp-750000000;
+	/delete-node/ opp-800000000;
+	/delete-node/ opp-900000000;
+};
diff --git a/arch/arm/boot/dts/tegra30-asus-tf300t.dts b/arch/arm/boot/dts/tegra30-asus-tf300t.dts
new file mode 100644
index 000000000000..f47434871a5c
--- /dev/null
+++ b/arch/arm/boot/dts/tegra30-asus-tf300t.dts
@@ -0,0 +1,1034 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include "tegra30-asus-transformer-common.dtsi"
+#include "tegra30-asus-lvds-display.dtsi"
+
+/ {
+	model = "Asus Transformer Pad TF300T";
+	compatible = "asus,tf300t", "nvidia,tegra30";
+
+	gpio@6000d000 {
+		tf300t-init-hog {
+			gpio-hog;
+			gpios = <TEGRA_GPIO(BB, 5) GPIO_ACTIVE_HIGH>;
+			output-low;
+		};
+	};
+
+	pinmux@70000868 {
+		state_default: pinmux {
+			lcd_pwr2_pc6 {
+				nvidia,pins = "lcd_pwr2_pc6",
+						"lcd_dc1_pd2";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			pbb3 {
+				nvidia,pins = "pbb3";
+				nvidia,function = "vgp3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			pbb7 {
+				nvidia,pins = "pbb7";
+				nvidia,function = "i2s4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			kb_row7_pr7 {
+				nvidia,pins = "kb_row7_pr7";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			gmi_cs4_n_pk2 {
+				nvidia,pins = "gmi_cs4_n_pk2";
+				nvidia,function = "gmi";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+		};
+	};
+
+	serial@70006200 {
+		/* Azurewave AW-NH615 BCM4329B1 */
+		bluetooth {
+			compatible = "brcm,bcm4329-bt";
+		};
+	};
+
+	i2c@7000c400 {
+		/* Elantech EKTH1036 touchscreen */
+		touchscreen@10 {
+			compatible = "elan,ektf3624";
+			reg = <0x10>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(H, 4) IRQ_TYPE_EDGE_FALLING>;
+			reset-gpios = <&gpio TEGRA_GPIO(H, 6) GPIO_ACTIVE_LOW>;
+
+			vcc33-supply = <&vdd_3v3_sys>;
+			vccio-supply = <&vdd_3v3_sys>;
+
+			touchscreen-size-x = <2240>;
+			touchscreen-size-y = <1408>;
+			touchscreen-inverted-y;
+		};
+	};
+
+	i2c@7000c500 {
+		clock-frequency = <400000>;
+
+		magnetometer@e {
+			mount-matrix =   "0", "-1",  "0",
+					"-1",  "0",  "0",
+					 "0",  "0", "-1";
+		};
+
+		gyroscope@68 {
+			mount-matrix =   "-1",  "0",  "0",
+					  "0",  "1",  "0",
+					  "0",  "0", "-1";
+
+			/* External I2C interface */
+			i2c-gate {
+				accelerometer@f {
+					mount-matrix =   "0", "-1",  "0",
+							"-1",  "0",  "0",
+							 "0",  "0",  "1";
+				};
+			};
+		};
+	};
+
+	i2c@7000d000 {
+		/* Wolfson Microelectronics WM8903 audio codec */
+		wm8903: audio-codec@1a {
+			compatible = "wlf,wm8903";
+			reg = <0x1a>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(W, 3) IRQ_TYPE_LEVEL_LOW>;
+
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			micdet-cfg = <0>;
+			micdet-delay = <100>;
+
+			gpio-cfg = <
+				0xffffffff /* don't touch */
+				0xffffffff /* don't touch */
+				0x00000000 /* Speaker-enable GPIO, output, low */
+				0xffffffff /* don't touch */
+				0xffffffff /* don't touch */
+			>;
+
+			AVDD-supply  = <&vdd_1v8_vio>;
+			CPVDD-supply = <&vdd_1v8_vio>;
+			DBVDD-supply = <&vdd_1v8_vio>;
+			DCVDD-supply = <&vdd_1v8_vio>;
+		};
+	};
+
+	memory-controller@7000f000 {
+		emc-timings-0 {
+			/* Elpida 1GB 667MHZ */
+			nvidia,ram-code = <0>;
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+
+				nvidia,emem-configuration = < 0x00030003 0xc0000020
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0502 0x74830303 0x001f0000 >;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+
+				nvidia,emem-configuration = < 0x00010003 0xc0000020
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0502 0x73430303 0x001f0000 >;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emem-configuration = < 0x00000003 0xc0000030
+					0x00000001 0x00000001 0x00000003 0x00000000
+					0x00000001 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0503 0x72830504 0x001f0000 >;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emem-configuration = < 0x00000006 0xc0000025
+					0x00000001 0x00000001 0x00000005 0x00000002
+					0x00000003 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0505 0x72440a06 0x001f0000 >;
+			};
+
+			timing-333500000 {
+				clock-frequency = <333500000>;
+
+				nvidia,emem-configuration = < 0x0000000a 0xc000003d
+					0x00000001 0x00000002 0x00000008 0x00000004
+					0x00000004 0x00000001 0x00000002 0x00000007
+					0x00000002 0x00000002 0x00000003 0x00000006
+					0x06030202 0x000b0608 0x70850f09 0x001f0000 >;
+			};
+
+			timing-667000000 {
+				clock-frequency = <667000000>;
+
+				nvidia,emem-configuration = < 0x00000014 0xc0000079
+					0x00000003 0x00000004 0x00000010 0x0000000b
+					0x0000000a 0x00000001 0x00000003 0x0000000b
+					0x00000002 0x00000002 0x00000004 0x00000008
+					0x08040202 0x00130b10 0x70ea1f11 0x001f0000 >;
+			};
+		};
+
+		emc-timings-1 {
+			/* Hynix 1GB 667MHZ */
+			nvidia,ram-code = <1>;
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+
+				nvidia,emem-configuration = < 0x00030003 0xc0000020
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0502 0x74830303 0x001f0000 >;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+
+				nvidia,emem-configuration = < 0x00010003 0xc0000020
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0502 0x73430303 0x001f0000 >;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emem-configuration = < 0x00000003 0xc0000030
+					0x00000001 0x00000001 0x00000003 0x00000000
+					0x00000001 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0503 0x72830504 0x001f0000 >;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emem-configuration = < 0x00000006 0xc0000025
+					0x00000001 0x00000001 0x00000005 0x00000002
+					0x00000003 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0605 0x72440a06 0x001f0000 >;
+			};
+
+			timing-333500000 {
+				clock-frequency = <333500000>;
+
+				nvidia,emem-configuration = < 0x0000000a 0xc000003d
+					0x00000001 0x00000002 0x00000008 0x00000005
+					0x00000004 0x00000001 0x00000002 0x00000007
+					0x00000002 0x00000002 0x00000003 0x00000006
+					0x06030202 0x000b0608 0x70850f09 0x001f0000 >;
+			};
+
+			timing-667000000 {
+				clock-frequency = <667000000>;
+
+				nvidia,emem-configuration = < 0x00000014 0xc0000079
+					0x00000003 0x00000004 0x00000011 0x0000000b
+					0x0000000a 0x00000001 0x00000003 0x0000000b
+					0x00000002 0x00000002 0x00000004 0x00000008
+					0x08040202 0x00140b11 0x70ea1f12 0x001f0000 >;
+			};
+		};
+
+		emc-timings-2 {
+			/* Micron 1GB 667MHZ */
+			nvidia,ram-code = <2>;
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+
+				nvidia,emem-configuration = < 0x00020001 0xc0000020
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0502 0x74830303 0x001f0000 >;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+
+				nvidia,emem-configuration = < 0x00010001 0xc0000020
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0502 0x73430303 0x001f0000 >;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emem-configuration = < 0x00000001 0xc0000030
+					0x00000001 0x00000001 0x00000003 0x00000000
+					0x00000001 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0503 0x72830504 0x001f0000 >;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emem-configuration = < 0x00000003 0xc0000025
+					0x00000001 0x00000001 0x00000005 0x00000002
+					0x00000003 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0505 0x72440a06 0x001f0000 >;
+			};
+
+			timing-333500000 {
+				clock-frequency = <333500000>;
+
+				nvidia,emem-configuration = < 0x00000005 0xc000003d
+					0x00000001 0x00000002 0x00000008 0x00000004
+					0x00000004 0x00000001 0x00000002 0x00000007
+					0x00000002 0x00000002 0x00000003 0x00000006
+					0x06030202 0x000b0608 0x70850f09 0x001f0000 >;
+			};
+
+			timing-667000000 {
+				clock-frequency = <667000000>;
+
+				nvidia,emem-configuration = < 0x0000000a 0xc0000079
+					0x00000003 0x00000004 0x00000010 0x0000000a
+					0x0000000a 0x00000001 0x00000003 0x0000000b
+					0x00000002 0x00000002 0x00000004 0x00000008
+					0x08040202 0x00140b10 0x70ea1f11 0x001f0000 >;
+			};
+		};
+	};
+
+	memory-controller@7000f400 {
+		emc-timings-0 {
+			/* Elpida 1GB 667MHZ */
+			nvidia,ram-code = <0>;
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200008>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000001
+					0x00000004 0x00000000 0x00000000 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000000
+					0x00000000 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000005 0x00000004 0x00000009
+					0x0000000b 0x000000c0 0x00000000 0x00000030
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000005 0x00000005
+					0x00000004 0x00000001 0x00000000 0x00000004
+					0x00000005 0x000000c7 0x00000006 0x00000004
+					0x00000000 0x00000000 0x00004288 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00000000
+					0x00000040 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x80000287 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200008>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000002
+					0x00000008 0x00000001 0x00000000 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000000
+					0x00000000 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000005 0x00000004 0x00000009
+					0x0000000b 0x00000181 0x00000000 0x00000060
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000009 0x00000009
+					0x00000004 0x00000002 0x00000000 0x00000004
+					0x00000005 0x0000018e 0x00000006 0x00000004
+					0x00000000 0x00000000 0x00004288 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00000000
+					0x00000040 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x8000040b 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200008>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000004
+					0x00000010 0x00000003 0x00000001 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000001
+					0x00000001 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000005 0x00000004 0x00000009
+					0x0000000b 0x00000303 0x00000000 0x000000c0
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000012 0x00000012
+					0x00000004 0x00000004 0x00000000 0x00000004
+					0x00000005 0x0000031c 0x00000006 0x00000004
+					0x00000000 0x00000000 0x00004288 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00000000
+					0x00000040 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x80000713 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200008>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x0000000a
+					0x00000020 0x00000007 0x00000002 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000002
+					0x00000002 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000005 0x00000004 0x00000009
+					0x0000000b 0x00000607 0x00000000 0x00000181
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000023 0x00000023
+					0x00000004 0x00000007 0x00000000 0x00000004
+					0x00000005 0x00000638 0x00000006 0x00000006
+					0x00000000 0x00000000 0x00004288 0x004400a4
+					0x00008000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00020000
+					0x00000100 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x80000d22 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-333500000 {
+				clock-frequency = <333500000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100002>;
+				nvidia,emc-mode-2 = <0x80200000>;
+				nvidia,emc-mode-reset = <0x80000321>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+
+				nvidia,emc-configuration =  < 0x0000000f
+					0x00000034 0x0000000a 0x00000003 0x00000003
+					0x00000008 0x00000002 0x00000009 0x00000003
+					0x00000003 0x00000002 0x00000001 0x00000000
+					0x00000004 0x00000006 0x00000004 0x0000000a
+					0x0000000c 0x000009e9 0x00000000 0x0000027a
+					0x00000001 0x00000008 0x00000001 0x00000000
+					0x00000007 0x0000000e 0x00000039 0x00000200
+					0x00000004 0x0000000a 0x00000000 0x00000004
+					0x00000005 0x00000a2a 0x00000000 0x00000004
+					0x00000000 0x00000000 0x00007088 0x002600a4
+					0x00008000 0x0003c000 0x0003c000 0x0003c000
+					0x0003c000 0x00014000 0x00014000 0x00014000
+					0x00014000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00048000 0x00048000 0x00048000
+					0x00048000 0x000002a0 0x0800013d 0x00000000
+					0x77fff884 0x01f1f508 0x05057404 0x54000007
+					0x080001e8 0x08000021 0x00000802 0x00020000
+					0x00000100 0x018b000c 0xa0f10000 0x00000000
+					0x00000000 0x800014d4 0xe8000000 0xff00ff89 >;
+			};
+
+			timing-667000000 {
+				clock-frequency = <667000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100002>;
+				nvidia,emc-mode-2 = <0x80200018>;
+				nvidia,emc-mode-reset = <0x80000b71>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x0000001f
+					0x00000069 0x00000017 0x00000007 0x00000005
+					0x0000000c 0x00000003 0x00000011 0x00000007
+					0x00000007 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000a 0x00000009 0x0000000a
+					0x00000011 0x00001412 0x00000000 0x00000504
+					0x00000002 0x0000000e 0x00000001 0x00000000
+					0x0000000c 0x00000016 0x00000072 0x00000200
+					0x00000005 0x00000015 0x00000000 0x00000006
+					0x00000007 0x00001453 0x0000000b 0x00000006
+					0x00000000 0x00000000 0x00005088 0xf00b0191
+					0x00008000 0x00000008 0x00000008 0x00000008
+					0x00000008 0x0000000a 0x0000000a 0x0000000a
+					0x0000000a 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x0000000a 0x0000000a 0x0000000a
+					0x0000000a 0x000002a0 0x0800013d 0x22220000
+					0x77fff884 0x01f1f501 0x07077404 0x54000000
+					0x080001e8 0x0f000021 0x00000802 0x00020000
+					0x00000100 0x0156000c 0xa0f10000 0x00000000
+					0x00000000 0x800028a5 0xe8000000 0xff00ff49 >;
+			};
+		};
+
+		emc-timings-1 {
+			/* Hynix 1GB 667MHZ */
+			nvidia,ram-code = <1>;
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200008>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000001
+					0x00000004 0x00000000 0x00000000 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000000
+					0x00000000 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000005 0x00000004 0x00000009
+					0x0000000b 0x000000c0 0x00000000 0x00000030
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000005 0x00000005
+					0x00000004 0x00000001 0x00000000 0x00000004
+					0x00000005 0x000000c7 0x00000006 0x00000004
+					0x00000000 0x00000000 0x00004288 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00000000
+					0x00000040 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x80000287 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200008>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000002
+					0x00000008 0x00000001 0x00000000 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000000
+					0x00000000 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000005 0x00000004 0x00000009
+					0x0000000b 0x00000181 0x00000000 0x00000060
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000009 0x00000009
+					0x00000004 0x00000002 0x00000000 0x00000004
+					0x00000005 0x0000018e 0x00000006 0x00000004
+					0x00000000 0x00000000 0x00004288 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00000000
+					0x00000040 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x8000040b 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200008>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000005
+					0x00000010 0x00000003 0x00000001 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000001
+					0x00000001 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000005 0x00000004 0x00000009
+					0x0000000b 0x00000303 0x00000000 0x000000c0
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000012 0x00000012
+					0x00000004 0x00000004 0x00000000 0x00000004
+					0x00000005 0x0000031c 0x00000006 0x00000004
+					0x00000000 0x00000000 0x00004288 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00000000
+					0x00000040 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x80000713 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200008>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x0000000a
+					0x00000020 0x00000007 0x00000003 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000002
+					0x00000002 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000005 0x00000004 0x00000009
+					0x0000000b 0x00000607 0x00000000 0x00000181
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000023 0x00000023
+					0x00000004 0x00000007 0x00000000 0x00000004
+					0x00000005 0x00000638 0x00000006 0x00000006
+					0x00000000 0x00000000 0x00004288 0x004400a4
+					0x00008000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00020000
+					0x00000100 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x80000d22 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-333500000 {
+				clock-frequency = <333500000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100002>;
+				nvidia,emc-mode-2 = <0x80200000>;
+				nvidia,emc-mode-reset = <0x80000321>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+
+				nvidia,emc-configuration =  < 0x0000000f
+					0x00000034 0x0000000b 0x00000003 0x00000003
+					0x00000008 0x00000002 0x00000009 0x00000003
+					0x00000003 0x00000002 0x00000001 0x00000000
+					0x00000004 0x00000006 0x00000004 0x0000000a
+					0x0000000c 0x000009e9 0x00000000 0x0000027a
+					0x00000001 0x00000008 0x00000001 0x00000000
+					0x00000007 0x0000000e 0x00000039 0x00000200
+					0x00000004 0x0000000a 0x00000000 0x00000004
+					0x00000005 0x00000a2a 0x00000000 0x00000004
+					0x00000000 0x00000000 0x00007088 0x002600a4
+					0x00008000 0x0003c000 0x0003c000 0x0003c000
+					0x0003c000 0x00014000 0x00014000 0x00014000
+					0x00014000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00048000 0x00048000 0x00048000
+					0x00048000 0x000002a0 0x0800013d 0x00000000
+					0x77fff884 0x01f1f508 0x05057404 0x54000007
+					0x080001e8 0x08000021 0x00000802 0x00020000
+					0x00000100 0x018b000c 0xa0f10000 0x00000000
+					0x00000000 0x800014d4 0xe8000000 0xff00ff89 >;
+			};
+
+			timing-667000000 {
+				clock-frequency = <667000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100002>;
+				nvidia,emc-mode-2 = <0x80200018>;
+				nvidia,emc-mode-reset = <0x80000b71>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000020
+					0x0000006a 0x00000018 0x00000008 0x00000005
+					0x0000000c 0x00000003 0x00000011 0x00000007
+					0x00000007 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000a 0x00000009 0x0000000a
+					0x00000011 0x00001412 0x00000000 0x00000504
+					0x00000002 0x0000000e 0x00000001 0x00000000
+					0x0000000c 0x00000016 0x00000072 0x00000200
+					0x00000005 0x00000015 0x00000000 0x00000006
+					0x00000007 0x00001453 0x0000000b 0x00000006
+					0x00000000 0x00000000 0x00005088 0xf00b0191
+					0x00008000 0x00000008 0x00000008 0x00000008
+					0x00000008 0x0000000a 0x0000000a 0x0000000a
+					0x0000000a 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x0000000c 0x0000000c 0x0000000c
+					0x0000000c 0x000002a0 0x0800013d 0x22220000
+					0x77fff884 0x01f1f501 0x07077404 0x54000000
+					0x080001e8 0x08000021 0x00000802 0x00020000
+					0x00000100 0x0155000c 0xa0f10000 0x00000000
+					0x00000000 0x800028a5 0xe8000000 0xff00ff49 >;
+			};
+		};
+
+		emc-timings-2 {
+			/* Micron 1GB 667MHZ */
+			nvidia,ram-code = <2>;
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200048>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000001
+					0x00000004 0x00000000 0x00000000 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000000
+					0x00000000 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000005 0x00000004 0x00000009
+					0x0000000b 0x000000c0 0x00000000 0x00000030
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000005 0x00000005
+					0x00000004 0x00000001 0x00000000 0x00000004
+					0x00000005 0x000000c7 0x00000006 0x00000004
+					0x00000000 0x00000000 0x00004288 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00000000
+					0x00000040 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x80000287 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200008>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000002
+					0x00000008 0x00000001 0x00000000 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000000
+					0x00000000 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000005 0x00000004 0x00000009
+					0x0000000b 0x00000181 0x00000000 0x00000060
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000009 0x00000009
+					0x00000004 0x00000002 0x00000000 0x00000004
+					0x00000005 0x0000018e 0x00000006 0x00000004
+					0x00000000 0x00000000 0x00004288 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00000000
+					0x00000040 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x8000040b 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200048>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000004
+					0x00000010 0x00000003 0x00000001 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000001
+					0x00000001 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000005 0x00000004 0x0000000a
+					0x0000000b 0x00000303 0x00000000 0x000000c0
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000012 0x00000012
+					0x00000004 0x00000004 0x00000000 0x00000004
+					0x00000005 0x0000031c 0x00000006 0x00000004
+					0x00000000 0x00000000 0x00004288 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00000000
+					0x00000040 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x80000713 0xd8000000 0xff00ff00 >;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200048>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000009
+					0x00000020 0x00000007 0x00000002 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000002
+					0x00000002 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000005 0x00000004 0x0000000a
+					0x0000000b 0x00000607 0x00000000 0x00000181
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000023 0x00000023
+					0x00000004 0x00000007 0x00000000 0x00000004
+					0x00000005 0x00000638 0x00000006 0x00000006
+					0x00000000 0x00000000 0x00004288 0x004400a4
+					0x00008000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00020000
+					0x00000100 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x80000d22 0xd8000000 0xff00ff00 >;
+			};
+
+			timing-333500000 {
+				clock-frequency = <333500000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100002>;
+				nvidia,emc-mode-2 = <0x80200040>;
+				nvidia,emc-mode-reset = <0x80000321>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+
+				nvidia,emc-configuration =  < 0x0000000f
+					0x00000034 0x0000000a 0x00000003 0x00000003
+					0x00000008 0x00000002 0x00000009 0x00000003
+					0x00000003 0x00000002 0x00000001 0x00000000
+					0x00000004 0x00000006 0x00000004 0x0000000a
+					0x0000000c 0x000009e9 0x00000000 0x0000027a
+					0x00000001 0x00000008 0x00000001 0x00000000
+					0x00000007 0x0000000e 0x00000039 0x00000200
+					0x00000004 0x0000000a 0x00000000 0x00000004
+					0x00000005 0x00000a2a 0x00000000 0x00000004
+					0x00000000 0x00000000 0x00007088 0x002600a4
+					0x00008000 0x0003c000 0x0003c000 0x0003c000
+					0x0003c000 0x00014000 0x00014000 0x00014000
+					0x00014000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00048000 0x00048000 0x00048000
+					0x00048000 0x000002a0 0x0800013d 0x00000000
+					0x77fff884 0x01f1f508 0x05057404 0x54000007
+					0x080001e8 0x08000021 0x00000802 0x00020000
+					0x00000100 0x018b000c 0xa0f10000 0x00000000
+					0x00000000 0x800014d4 0xe8000000 0xff00ff89 >;
+			};
+
+			timing-667000000 {
+				clock-frequency = <667000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100002>;
+				nvidia,emc-mode-2 = <0x80200058>;
+				nvidia,emc-mode-reset = <0x80000b71>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x0000001f
+					0x00000069 0x00000016 0x00000007 0x00000005
+					0x0000000c 0x00000003 0x00000011 0x00000008
+					0x00000008 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000a 0x00000009 0x0000000b
+					0x00000011 0x00001412 0x00000000 0x00000504
+					0x00000002 0x0000000e 0x00000001 0x00000000
+					0x0000000c 0x00000016 0x00000072 0x00000200
+					0x00000005 0x00000015 0x00000000 0x00000006
+					0x00000007 0x00001453 0x0000000b 0x00000006
+					0x00000000 0x00000000 0x00005088 0xf00b0191
+					0x00008000 0x0000000a 0x0000000a 0x0000000a
+					0x0000000a 0x0000000a 0x0000000a 0x0000000a
+					0x0000000a 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x0000000c 0x0000000c 0x0000000c
+					0x0000000c 0x000002a0 0x0800013d 0x22220000
+					0x77fff884 0x01f1f501 0x07077404 0x54000000
+					0x080001e8 0x08000021 0x00000802 0x00020000
+					0x00000100 0x0156000c 0xa0f10000 0x00000000
+					0x00000000 0x800028a5 0xf8000000 0xff00ff49 >;
+			};
+		};
+	};
+
+	display-panel {
+		compatible = "innolux,g101ice-l01";
+	};
+
+	sound {
+		compatible = "asus,tegra-audio-wm8903-tf300t",
+			     "nvidia,tegra-audio-wm8903";
+		nvidia,model = "Asus Transformer Pad TF300T WM8903";
+
+		nvidia,audio-routing =
+			"Headphone Jack", "HPOUTR",
+			"Headphone Jack", "HPOUTL",
+			"Int Spk", "ROP",
+			"Int Spk", "RON",
+			"Int Spk", "LOP",
+			"Int Spk", "LON",
+			"IN1L", "Mic Jack",
+			"IN2L", "Mic Jack",
+			"DMICDAT", "Int Mic";
+
+		nvidia,audio-codec = <&wm8903>;
+		nvidia,spkr-en-gpios = <&wm8903 2 GPIO_ACTIVE_HIGH>;
+		nvidia,headset;
+	};
+};
+
+&emc_icc_dvfs_opp_table {
+	/delete-node/ opp-750000000-1300;
+	/delete-node/ opp-800000000-1300;
+	/delete-node/ opp-900000000-1350;
+};
+
+&emc_bw_dfs_opp_table {
+	/delete-node/ opp-750000000;
+	/delete-node/ opp-800000000;
+	/delete-node/ opp-900000000;
+};
diff --git a/arch/arm/boot/dts/tegra30-asus-tf300tg.dts b/arch/arm/boot/dts/tegra30-asus-tf300tg.dts
new file mode 100644
index 000000000000..96345f821c3d
--- /dev/null
+++ b/arch/arm/boot/dts/tegra30-asus-tf300tg.dts
@@ -0,0 +1,1087 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include "tegra30-asus-transformer-common.dtsi"
+#include "tegra30-asus-lvds-display.dtsi"
+
+/ {
+	model = "Asus Transformer Pad 3G TF300TG";
+	compatible = "asus,tf300tg", "nvidia,tegra30";
+
+	gpio@6000d000 {
+		tf300tg-init-hog {
+			gpio-hog;
+			gpios = <TEGRA_GPIO(C, 6) GPIO_ACTIVE_HIGH>,
+				<TEGRA_GPIO(D, 2) GPIO_ACTIVE_HIGH>,
+				<TEGRA_GPIO(P, 1) GPIO_ACTIVE_HIGH>,
+				<TEGRA_GPIO(X, 5) GPIO_ACTIVE_HIGH>,
+				<TEGRA_GPIO(W, 3) GPIO_ACTIVE_HIGH>,
+				<TEGRA_GPIO(R, 3) GPIO_ACTIVE_HIGH>,
+				<TEGRA_GPIO(U, 5) GPIO_ACTIVE_HIGH>,
+				<TEGRA_GPIO(X, 7) GPIO_ACTIVE_HIGH>,
+				<TEGRA_GPIO(X, 0) GPIO_ACTIVE_HIGH>,
+				<TEGRA_GPIO(Y, 2) GPIO_ACTIVE_HIGH>,
+				<TEGRA_GPIO(Y, 3) GPIO_ACTIVE_HIGH>,
+				<TEGRA_GPIO(EE, 1) GPIO_ACTIVE_HIGH>,
+				<TEGRA_GPIO(R, 7) GPIO_ACTIVE_HIGH>,
+				<TEGRA_GPIO(U, 3) GPIO_ACTIVE_HIGH>;
+			output-low;
+		};
+	};
+
+	pinmux@70000868 {
+		state_default: pinmux {
+			pbb3 {
+				nvidia,pins = "pbb3";
+				nvidia,function = "vgp3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			pbb7 {
+				nvidia,pins = "pbb7";
+				nvidia,function = "i2s4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			gmi_cs4_n_pk2 {
+				nvidia,pins = "gmi_cs4_n_pk2";
+				nvidia,function = "gmi";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			lcd_pwr2_pc6 {
+				nvidia,pins = "lcd_pwr2_pc6",
+						"lcd_dc1_pd2";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			kb_row7_pr7 {
+				nvidia,pins = "kb_row7_pr7";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			spi2_cs2_n_pw3 {
+				nvidia,pins = "spi2_cs2_n_pw3";
+				nvidia,function = "spi2";
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+			};
+
+			dap3_din_pp1 {
+				nvidia,pins = "dap3_din_pp1";
+				nvidia,function = "i2s2";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			spi1_sck_px5 {
+				nvidia,pins = "spi1_sck_px5";
+				nvidia,function = "spi1";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			pu5 {
+				nvidia,pins = "pu5";
+				nvidia,function = "pwm2";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			spi2_mosi_px0 {
+				nvidia,pins = "spi2_mosi_px0";
+				nvidia,function = "spi2";
+			};
+
+			spi1_miso_px7 {
+				nvidia,pins = "spi1_miso_px7";
+				nvidia,function = "spi1";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			clk3_req_pee1 {
+				nvidia,pins = "clk3_req_pee1";
+				nvidia,function = "dev3";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			ulpi_nxt_py2 {
+				nvidia,pins = "ulpi_nxt_py2";
+				nvidia,function = "uartd";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			ulpi_stp_py3 {
+				nvidia,pins = "ulpi_stp_py3";
+				nvidia,function = "uartd";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			pu3 {
+				nvidia,pins = "pu3";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			dap1_din_pn1 {
+				nvidia,pins = "dap1_din_pn1";
+				nvidia,function = "i2s0";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+		};
+	};
+
+	serial@70006200 {
+		/* Azurewave AW-NH615 BCM4329B1 */
+		bluetooth {
+			compatible = "brcm,bcm4329-bt";
+		};
+	};
+
+	i2c@7000c400 {
+		/* Elantech EKTH1036 touchscreen */
+		touchscreen@10 {
+			compatible = "elan,ektf3624";
+			reg = <0x10>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(H, 4) IRQ_TYPE_EDGE_FALLING>;
+			reset-gpios = <&gpio TEGRA_GPIO(H, 6) GPIO_ACTIVE_LOW>;
+
+			vcc33-supply = <&vdd_3v3_sys>;
+			vccio-supply = <&vdd_3v3_sys>;
+
+			touchscreen-size-x = <2240>;
+			touchscreen-size-y = <1408>;
+			touchscreen-inverted-y;
+		};
+	};
+
+	i2c@7000c500 {
+		clock-frequency = <400000>;
+
+		magnetometer@e {
+			mount-matrix =   "1",  "0",  "0",
+					 "0", "-1",  "0",
+					 "0",  "0", "-1";
+		};
+
+		gyroscope@68 {
+			mount-matrix =   "-1",  "0",  "0",
+					  "0",  "1",  "0",
+					  "0",  "0", "-1";
+
+			/* External I2C interface */
+			i2c-gate {
+				accelerometer@f {
+					mount-matrix =   "0", "-1",  "0",
+							"-1",  "0",  "0",
+							 "0",  "0",  "1";
+				};
+			};
+		};
+	};
+
+	i2c@7000d000 {
+		/* Realtek ALC5631 audio codec */
+		rt5631: audio-codec@1a {
+			compatible = "realtek,rt5631";
+			reg = <0x1a>;
+		};
+	};
+
+	memory-controller@7000f000 {
+		emc-timings-0 {
+			/* Elpida 1GB 667MHZ */
+			nvidia,ram-code = <0>;
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+
+				nvidia,emem-configuration = < 0x00020001 0xc0000020
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0502 0x74830303 0x001f0000 >;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+
+				nvidia,emem-configuration = < 0x00010001 0xc0000020
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0502 0x73430303 0x001f0000 >;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emem-configuration = < 0x00000001 0xc0000030
+					0x00000001 0x00000001 0x00000003 0x00000000
+					0x00000001 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0503 0x72830504 0x001f0000 >;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emem-configuration = < 0x00000003 0xc0000025
+					0x00000001 0x00000001 0x00000005 0x00000002
+					0x00000003 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0505 0x72440a06 0x001f0000 >;
+			};
+
+			timing-333500000 {
+				clock-frequency = <333500000>;
+
+				nvidia,emem-configuration = < 0x00000005 0xc000003d
+					0x00000001 0x00000002 0x00000008 0x00000004
+					0x00000004 0x00000001 0x00000002 0x00000007
+					0x00000002 0x00000002 0x00000003 0x00000006
+					0x06030202 0x000b0608 0x70850f09 0x001f0000 >;
+			};
+
+			timing-667000000 {
+				clock-frequency = <667000000>;
+
+				nvidia,emem-configuration = < 0x0000000a 0xc0000079
+					0x00000003 0x00000004 0x00000010 0x0000000b
+					0x0000000a 0x00000001 0x00000003 0x0000000b
+					0x00000002 0x00000002 0x00000004 0x00000008
+					0x08040202 0x00130b10 0x70ea1f11 0x001f0000 >;
+			};
+		};
+
+		emc-timings-1 {
+			/* Hynix 1GB 667MHZ */
+			nvidia,ram-code = <1>;
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+
+				nvidia,emem-configuration = < 0x00020001 0xc0000020
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0502 0x74830303 0x001f0000 >;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+
+				nvidia,emem-configuration = < 0x00010001 0xc0000020
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0502 0x73430303 0x001f0000 >;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emem-configuration = < 0x00000001 0xc0000030
+					0x00000001 0x00000001 0x00000003 0x00000000
+					0x00000001 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0503 0x72830504 0x001f0000 >;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emem-configuration = < 0x00000003 0xc0000025
+					0x00000001 0x00000001 0x00000005 0x00000002
+					0x00000003 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0505 0x72440a06 0x001f0000 >;
+			};
+
+			timing-333500000 {
+				clock-frequency = <333500000>;
+
+				nvidia,emem-configuration = < 0x00000005 0xc000003d
+					0x00000001 0x00000002 0x00000008 0x00000004
+					0x00000004 0x00000001 0x00000002 0x00000007
+					0x00000002 0x00000002 0x00000003 0x00000006
+					0x06030202 0x000b0608 0x70850f09 0x001f0000 >;
+			};
+
+			timing-667000000 {
+				clock-frequency = <667000000>;
+
+				nvidia,emem-configuration = < 0x0000000a 0xc0000079
+					0x00000003 0x00000004 0x00000010 0x0000000b
+					0x0000000a 0x00000001 0x00000003 0x0000000b
+					0x00000002 0x00000002 0x00000004 0x00000008
+					0x08040202 0x00130b10 0x70ea1f11 0x001f0000 >;
+			};
+		};
+
+		emc-timings-2 {
+			/* Micron 1GB 667MHZ */
+			nvidia,ram-code = <2>;
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+
+				nvidia,emem-configuration = < 0x00020001 0xc0000020
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0502 0x74830303 0x001f0000 >;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+
+				nvidia,emem-configuration = < 0x00010001 0xc0000020
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0502 0x73430303 0x001f0000 >;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emem-configuration = < 0x00000001 0xc0000030
+					0x00000001 0x00000001 0x00000003 0x00000000
+					0x00000001 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0503 0x72830504 0x001f0000 >;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emem-configuration = < 0x00000003 0xc0000025
+					0x00000001 0x00000001 0x00000005 0x00000002
+					0x00000003 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0505 0x72440a06 0x001f0000 >;
+			};
+
+			timing-333500000 {
+				clock-frequency = <333500000>;
+
+				nvidia,emem-configuration = < 0x00000005 0x8000003d
+					0x00000001 0x00000002 0x00000008 0x00000004
+					0x00000004 0x00000001 0x00000002 0x00000007
+					0x00000002 0x00000002 0x00000003 0x00000006
+					0x06030202 0x000b0608 0x70850f09 0x001f0000 >;
+			};
+
+			timing-667000000 {
+				clock-frequency = <667000000>;
+
+				nvidia,emem-configuration = < 0x0000000a 0x80000079
+					0x00000003 0x00000004 0x00000010 0x0000000a
+					0x0000000a 0x00000001 0x00000003 0x0000000b
+					0x00000002 0x00000002 0x00000004 0x00000008
+					0x08040202 0x00130b10 0x70ea1f11 0x001f0000 >;
+			};
+		};
+	};
+
+	memory-controller@7000f400 {
+		emc-timings-0 {
+			/* Elpida 1GB 667MHZ */
+			nvidia,ram-code = <0>;
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200048>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000001
+					0x00000004 0x00000000 0x00000000 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000000
+					0x00000000 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000005 0x00000004 0x0000000a
+					0x0000000b 0x000000c0 0x00000000 0x00000030
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000005 0x00000005
+					0x00000004 0x00000001 0x00000000 0x00000004
+					0x00000005 0x000000c7 0x00000006 0x00000004
+					0x00000000 0x00000000 0x00004288 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00000000
+					0x00000040 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x80000287 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200048>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000002
+					0x00000008 0x00000001 0x00000000 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000000
+					0x00000000 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000005 0x00000004 0x0000000a
+					0x0000000b 0x00000181 0x00000000 0x00000060
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000009 0x00000009
+					0x00000004 0x00000002 0x00000000 0x00000004
+					0x00000005 0x0000018e 0x00000006 0x00000004
+					0x00000000 0x00000000 0x00004288 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00000000
+					0x00000040 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x8000040b 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200048>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000005
+					0x00000010 0x00000003 0x00000001 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000001
+					0x00000001 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000005 0x00000004 0x0000000a
+					0x0000000b 0x00000303 0x00000000 0x000000c0
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000012 0x00000012
+					0x00000004 0x00000004 0x00000000 0x00000004
+					0x00000005 0x0000031c 0x00000006 0x00000004
+					0x00000000 0x00000000 0x00004288 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00000000
+					0x00000040 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x80000713 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200048>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x0000000a
+					0x00000020 0x00000007 0x00000002 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000002
+					0x00000002 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000006 0x00000004 0x0000000a
+					0x0000000b 0x00000607 0x00000000 0x00000181
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000023 0x00000023
+					0x00000004 0x00000007 0x00000000 0x00000004
+					0x00000005 0x00000638 0x00000007 0x00000004
+					0x00000000 0x00000000 0x00004288 0x004400a4
+					0x00008000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00020000
+					0x00000100 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x80000d22 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-333500000 {
+				clock-frequency = <333500000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100002>;
+				nvidia,emc-mode-2 = <0x80200040>;
+				nvidia,emc-mode-reset = <0x80000321>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+
+				nvidia,emc-configuration =  < 0x0000000f
+					0x00000034 0x0000000a 0x00000003 0x00000003
+					0x00000008 0x00000002 0x00000009 0x00000003
+					0x00000003 0x00000002 0x00000001 0x00000000
+					0x00000004 0x00000006 0x00000004 0x0000000a
+					0x0000000c 0x000009e9 0x00000000 0x0000027a
+					0x00000001 0x00000008 0x00000001 0x00000000
+					0x00000007 0x0000000e 0x00000039 0x00000200
+					0x00000004 0x0000000a 0x00000000 0x00000004
+					0x00000005 0x00000a2a 0x00000000 0x00000004
+					0x00000000 0x00000000 0x00007088 0x002600a4
+					0x00008000 0x0003c000 0x0003c000 0x0003c000
+					0x0003c000 0x00014000 0x00014000 0x00014000
+					0x00014000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00050000 0x00050000 0x00050000
+					0x00050000 0x000002a0 0x0800013d 0x00000000
+					0x77fff884 0x01f1f508 0x05057404 0x54000007
+					0x080001e8 0x08000021 0x00000802 0x00020000
+					0x00000100 0x018b000c 0xa0f10000 0x00000000
+					0x00000000 0x800014d4 0xe8000000 0xff00ff89 >;
+			};
+
+			timing-667000000 {
+				clock-frequency = <667000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100002>;
+				nvidia,emc-mode-2 = <0x80200058>;
+				nvidia,emc-mode-reset = <0x80000b71>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x0000001f
+					0x00000069 0x00000017 0x00000007 0x00000005
+					0x0000000c 0x00000003 0x00000011 0x00000007
+					0x00000007 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000b 0x00000009 0x0000000b
+					0x00000011 0x00001412 0x00000000 0x00000504
+					0x00000002 0x0000000e 0x00000001 0x00000000
+					0x0000000c 0x00000016 0x00000072 0x00000200
+					0x00000005 0x00000015 0x00000000 0x00000006
+					0x00000007 0x00001453 0x0000000c 0x00000004
+					0x00000000 0x00000000 0x00005088 0xf00b0191
+					0x00008000 0x0000000c 0x0000000c 0x0000000c
+					0x0000000c 0x0000000a 0x0000000a 0x0000000a
+					0x0000000a 0x00018000 0x00018000 0x00018000
+					0x00018000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x0000000c 0x0000000c 0x0000000c
+					0x0000000c 0x000002a0 0x0a00013d 0x22220000
+					0x77fff884 0x01f1f501 0x07077404 0x54000000
+					0x080001e8 0x0a000021 0x00000802 0x00020000
+					0x00000100 0x0156000c 0xa0f10000 0x00000000
+					0x00000000 0x800028a5 0xe8000000 0xff00ff49 >;
+			};
+		};
+
+		emc-timings-1 {
+			/* Hynix 1GB 667MHZ */
+			nvidia,ram-code = <1>;
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200048>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000001
+					0x00000004 0x00000000 0x00000000 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000000
+					0x00000000 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000005 0x00000004 0x0000000a
+					0x0000000b 0x000000c0 0x00000000 0x00000030
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000005 0x00000005
+					0x00000004 0x00000001 0x00000000 0x00000004
+					0x00000005 0x000000c7 0x00000006 0x00000004
+					0x00000000 0x00000000 0x00004288 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00000000
+					0x00000040 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x80000287 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200048>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000002
+					0x00000008 0x00000001 0x00000000 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000000
+					0x00000000 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000005 0x00000004 0x0000000a
+					0x0000000b 0x00000181 0x00000000 0x00000060
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000009 0x00000009
+					0x00000004 0x00000002 0x00000000 0x00000004
+					0x00000005 0x0000018e 0x00000006 0x00000004
+					0x00000000 0x00000000 0x00004288 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00000000
+					0x00000040 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x8000040b 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200048>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000005
+					0x00000010 0x00000003 0x00000001 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000001
+					0x00000001 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000005 0x00000004 0x0000000a
+					0x0000000b 0x00000303 0x00000000 0x000000c0
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000012 0x00000012
+					0x00000004 0x00000004 0x00000000 0x00000004
+					0x00000005 0x0000031c 0x00000006 0x00000004
+					0x00000000 0x00000000 0x00004288 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00000000
+					0x00000040 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x80000713 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200048>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x0000000a
+					0x00000020 0x00000007 0x00000002 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000002
+					0x00000002 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000006 0x00000004 0x0000000a
+					0x0000000b 0x00000607 0x00000000 0x00000181
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000023 0x00000023
+					0x00000004 0x00000007 0x00000000 0x00000004
+					0x00000005 0x00000638 0x00000007 0x00000004
+					0x00000000 0x00000000 0x00004288 0x004400a4
+					0x00008000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00020000
+					0x00000100 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x80000d22 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-333500000 {
+				clock-frequency = <333500000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100002>;
+				nvidia,emc-mode-2 = <0x80200040>;
+				nvidia,emc-mode-reset = <0x80000321>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+
+				nvidia,emc-configuration =  < 0x0000000f
+					0x00000034 0x0000000a 0x00000003 0x00000003
+					0x00000008 0x00000002 0x00000009 0x00000003
+					0x00000003 0x00000002 0x00000001 0x00000000
+					0x00000004 0x00000006 0x00000004 0x0000000a
+					0x0000000c 0x000009e9 0x00000000 0x0000027a
+					0x00000001 0x00000008 0x00000001 0x00000000
+					0x00000007 0x0000000e 0x00000039 0x00000200
+					0x00000004 0x0000000a 0x00000000 0x00000004
+					0x00000005 0x00000a2a 0x00000000 0x00000004
+					0x00000000 0x00000000 0x00007088 0x002600a4
+					0x00008000 0x0003c000 0x0003c000 0x0003c000
+					0x0003c000 0x00014000 0x00014000 0x00014000
+					0x00014000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00048000 0x00048000 0x00048000
+					0x00048000 0x000002a0 0x0800013d 0x00000000
+					0x77fff884 0x01f1f508 0x05057404 0x54000007
+					0x080001e8 0x08000021 0x00000802 0x00020000
+					0x00000100 0x018b000c 0xa0f10000 0x00000000
+					0x00000000 0x800014d4 0xe8000000 0xff00ff89 >;
+			};
+
+			timing-667000000 {
+				clock-frequency = <667000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100002>;
+				nvidia,emc-mode-2 = <0x80200058>;
+				nvidia,emc-mode-reset = <0x80000b71>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000020
+					0x00000069 0x00000017 0x00000007 0x00000005
+					0x0000000c 0x00000003 0x00000011 0x00000007
+					0x00000007 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000b 0x00000009 0x0000000b
+					0x00000011 0x00001412 0x00000000 0x00000504
+					0x00000002 0x0000000e 0x00000001 0x00000000
+					0x0000000c 0x00000016 0x00000072 0x00000200
+					0x00000005 0x00000015 0x00000000 0x00000006
+					0x00000007 0x00001453 0x0000000c 0x00000004
+					0x00000000 0x00000000 0x00005088 0xf00b0191
+					0x00008000 0x0000000a 0x0000000a 0x0000000a
+					0x0000000a 0x0000000a 0x0000000a 0x0000000a
+					0x0000000a 0x00018000 0x00018000 0x00018000
+					0x00018000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x0000000a 0x0000000a 0x0000000a
+					0x0000000a 0x000002a0 0x0800013d 0x22220000
+					0x77fff884 0x01f1f501 0x07077404 0x54000000
+					0x080001e8 0x08000021 0x00000802 0x00020000
+					0x00000100 0x0156000c 0xa0f10000 0x00000000
+					0x00000000 0x800028a5 0xe8000000 0xff00ff49 >;
+			};
+		};
+
+		emc-timings-2 {
+			/* Micron 1GB 667MHZ */
+			nvidia,ram-code = <2>;
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200008>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000001
+					0x00000004 0x00000000 0x00000000 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000000
+					0x00000000 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000005 0x00000004 0x0000000a
+					0x0000000b 0x000000c0 0x00000000 0x00000030
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000005 0x00000005
+					0x00000004 0x00000001 0x00000000 0x00000004
+					0x00000005 0x000000c7 0x00000006 0x00000004
+					0x00000000 0x00000000 0x00004288 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00000000
+					0x00000040 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x80000287 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200008>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000002
+					0x00000008 0x00000001 0x00000000 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000000
+					0x00000000 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000005 0x00000004 0x0000000a
+					0x0000000b 0x00000181 0x00000000 0x00000060
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000009 0x00000009
+					0x00000004 0x00000002 0x00000000 0x00000004
+					0x00000005 0x0000018e 0x00000006 0x00000004
+					0x00000000 0x00000000 0x00004288 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00000000
+					0x00000040 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x8000040b 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200008>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000004
+					0x00000010 0x00000003 0x00000001 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000001
+					0x00000001 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000005 0x00000004 0x0000000a
+					0x0000000b 0x00000303 0x00000000 0x000000c0
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000012 0x00000012
+					0x00000004 0x00000004 0x00000000 0x00000004
+					0x00000005 0x0000031c 0x00000006 0x00000004
+					0x00000000 0x00000000 0x00004288 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00000000
+					0x00000040 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x80000713 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200008>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000009
+					0x00000020 0x00000007 0x00000002 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000002
+					0x00000002 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000006 0x00000004 0x0000000a
+					0x0000000b 0x00000607 0x00000000 0x00000181
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000023 0x00000023
+					0x00000004 0x00000007 0x00000000 0x00000004
+					0x00000005 0x00000638 0x00000007 0x00000004
+					0x00000000 0x00000000 0x00004288 0x004400a4
+					0x00008000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00020000
+					0x00000100 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x80000d22 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-333500000 {
+				clock-frequency = <333500000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100002>;
+				nvidia,emc-mode-2 = <0x80200000>;
+				nvidia,emc-mode-reset = <0x80000321>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+
+				nvidia,emc-configuration =  < 0x0000000f
+					0x00000034 0x0000000a 0x00000003 0x00000003
+					0x00000008 0x00000002 0x00000009 0x00000003
+					0x00000003 0x00000002 0x00000001 0x00000000
+					0x00000004 0x00000006 0x00000004 0x0000000a
+					0x0000000c 0x000009e9 0x00000000 0x0000027a
+					0x00000001 0x00000008 0x00000001 0x00000000
+					0x00000007 0x0000000e 0x00000039 0x00000200
+					0x00000004 0x0000000a 0x00000000 0x00000004
+					0x00000005 0x00000a2a 0x00000000 0x00000004
+					0x00000000 0x00000000 0x00007088 0x002600a4
+					0x00008000 0x0003c000 0x0003c000 0x0003c000
+					0x0003c000 0x00014000 0x00014000 0x00014000
+					0x00014000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00040000 0x00040000 0x00040000
+					0x00040000 0x000002a0 0x0800013d 0x00000000
+					0x77fff884 0x01f1f508 0x05057404 0x54000007
+					0x080001e8 0x08000021 0x00000802 0x00020000
+					0x00000100 0x018b000c 0xa0f10000 0x00000000
+					0x00000000 0x800014d4 0xe8000000 0xff00ff89 >;
+			};
+
+			timing-667000000 {
+				clock-frequency = <667000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100002>;
+				nvidia,emc-mode-2 = <0x80200018>;
+				nvidia,emc-mode-reset = <0x80000b71>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x0000001f
+					0x00000069 0x00000016 0x00000007 0x00000005
+					0x0000000c 0x00000003 0x00000011 0x00000007
+					0x00000007 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000b 0x00000009 0x0000000b
+					0x00000011 0x00001412 0x00000000 0x00000504
+					0x00000002 0x0000000e 0x00000001 0x00000000
+					0x0000000c 0x00000016 0x00000072 0x00000200
+					0x00000005 0x00000015 0x00000000 0x00000006
+					0x00000007 0x00001453 0x0000000c 0x00000004
+					0x00000000 0x00000000 0x00005088 0xf00b0191
+					0x00008000 0x0000000a 0x0000000a 0x0000000a
+					0x0000000a 0x0000000a 0x0000000a 0x0000000a
+					0x0000000a 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x0000000a 0x0000000a 0x0000000a
+					0x0000000a 0x000002a0 0x0600013d 0x22220000
+					0x77fff884 0x01f1f501 0x07077404 0x54000000
+					0x080001e8 0x08000021 0x00000802 0x00020000
+					0x00000100 0x0156000c 0xa0f10000 0x00000000
+					0x00000000 0x800028a5 0xe8000000 0xff00ff49 >;
+			};
+		};
+	};
+
+	display-panel {
+		compatible = "innolux,g101ice-l01";
+	};
+};
+
+&emc_icc_dvfs_opp_table {
+	/delete-node/ opp-750000000-1300;
+	/delete-node/ opp-800000000-1300;
+	/delete-node/ opp-900000000-1350;
+};
+
+&emc_bw_dfs_opp_table {
+	/delete-node/ opp-750000000;
+	/delete-node/ opp-800000000;
+	/delete-node/ opp-900000000;
+};
diff --git a/arch/arm/boot/dts/tegra30-asus-tf700t.dts b/arch/arm/boot/dts/tegra30-asus-tf700t.dts
new file mode 100644
index 000000000000..1a331dec3cfe
--- /dev/null
+++ b/arch/arm/boot/dts/tegra30-asus-tf700t.dts
@@ -0,0 +1,823 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include "tegra30-asus-transformer-common.dtsi"
+
+/ {
+	model = "Asus Transformer Infinity TF700T";
+	compatible = "asus,tf700t", "nvidia,tegra30";
+
+	host1x@50000000 {
+		lcd: dc@54200000 {
+			clocks = <&tegra_car TEGRA30_CLK_DISP1>,
+				 <&tegra_car TEGRA30_CLK_PLL_D_OUT0>;
+
+			rgb {
+				status = "okay";
+
+				port@0 {
+					dpi_output: endpoint {
+						remote-endpoint = <&bridge_input>;
+						bus-width = <24>;
+					};
+				};
+			};
+		};
+	};
+
+	pinmux@70000868 {
+		state_default: pinmux {
+			lcd_pwr2_pc6 {
+				nvidia,pins = "lcd_pwr2_pc6",
+						"lcd_dc1_pd2";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pbb3 {
+				nvidia,pins = "pbb3";
+				nvidia,function = "vgp3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			spi2_mosi_px0 {
+				nvidia,pins = "spi2_mosi_px0";
+				nvidia,function = "spi2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pbb7 {
+				nvidia,pins = "pbb7";
+				nvidia,function = "i2s4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			kb_row7_pr7 {
+				nvidia,pins = "kb_row7_pr7";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			gmi_cs4_n_pk2 {
+				nvidia,pins = "gmi_cs4_n_pk2";
+				nvidia,function = "gmi";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+		};
+	};
+
+	serial@70006200 {
+		/* Azurewave AW-NH665 BCM4330B1 */
+		bluetooth {
+			compatible = "brcm,bcm4330-bt";
+		};
+	};
+
+	i2c@7000c400 {
+		/* Elantech ELAN-3024-7053 or 5184N FPC-1 REV: 2/3 touchscreen */
+		touchscreen@10 {
+			compatible = "elan,ektf3624";
+			reg = <0x10>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(H, 4) IRQ_TYPE_EDGE_FALLING>;
+			reset-gpios = <&gpio TEGRA_GPIO(H, 6) GPIO_ACTIVE_LOW>;
+
+			vcc33-supply = <&vdd_3v3_sys>;
+			vccio-supply = <&vdd_3v3_sys>;
+
+			touchscreen-size-x = <2944>;
+			touchscreen-size-y = <1856>;
+			touchscreen-inverted-y;
+		};
+	};
+
+	i2c@7000c500 {
+		clock-frequency = <100000>;
+
+		magnetometer@e {
+			mount-matrix =   "1",  "0",  "0",
+					 "0", "-1",  "0",
+					 "0",  "0", "-1";
+		};
+
+		gyroscope@68 {
+			mount-matrix =   "0",  "1",  "0",
+					 "1",  "0",  "0",
+					 "0",  "0", "-1";
+
+			/* External I2C interface */
+			i2c-gate {
+				accelerometer@f {
+					mount-matrix =   "0", "-1",  "0",
+							"-1",  "0",  "0",
+							 "0",  "0",  "1";
+				};
+			};
+		};
+	};
+
+	i2c@7000d000 {
+		/* Realtek ALC5631 audio codec */
+		rt5631: audio-codec@1a {
+			compatible = "realtek,rt5631";
+			reg = <0x1a>;
+		};
+	};
+
+	memory-controller@7000f000 {
+		emc-timings-0 {
+			/* Micron 1GB 800MHZ */
+			nvidia,ram-code = <0>;
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+
+				nvidia,emem-configuration = < 0x00020001 0xc0000020
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0502 0x75830303 0x001f0000 >;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+
+				nvidia,emem-configuration = < 0x00010001 0xc0000020
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0502 0x74630303 0x001f0000 >;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emem-configuration = < 0x00000001 0xc0000030
+					0x00000001 0x00000001 0x00000003 0x00000000
+					0x00000002 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0503 0x73c30504 0x001f0000 >;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emem-configuration = < 0x00000003 0xc0000025
+					0x00000001 0x00000001 0x00000005 0x00000002
+					0x00000004 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0505 0x73840a06 0x001f0000 >;
+			};
+
+			timing-400000000 {
+				clock-frequency = <400000000>;
+
+				nvidia,emem-configuration = < 0x00000006 0xc0000048
+					0x00000001 0x00000002 0x00000009 0x00000005
+					0x00000007 0x00000001 0x00000002 0x00000008
+					0x00000002 0x00000002 0x00000003 0x00000006
+					0x06030202 0x000d0709 0x7086120a 0x001f0000 >;
+			};
+
+			timing-800000000 {
+				clock-frequency = <800000000>;
+
+				nvidia,emem-configuration = < 0x0000000c 0xc0000090
+					0x00000004 0x00000005 0x00000013 0x0000000c
+					0x0000000f 0x00000002 0x00000003 0x0000000c
+					0x00000002 0x00000002 0x00000004 0x00000008
+					0x08040202 0x00160d13 0x712c2414 0x001f0000 >;
+			};
+		};
+
+		emc-timings-1 {
+			/* Elpida 1GB 800MHZ */
+			nvidia,ram-code = <1>;
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+
+				nvidia,emem-configuration = < 0x00020001 0xc0000020
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0502 0x75830303 0x001f0000 >;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+
+				nvidia,emem-configuration = < 0x00010001 0xc0000020
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0502 0x74630303 0x001f0000 >;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emem-configuration = < 0x00000001 0xc0000030
+					0x00000001 0x00000001 0x00000003 0x00000000
+					0x00000002 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0503 0x73c30504 0x001f0000 >;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emem-configuration = < 0x00000003 0xc0000025
+					0x00000001 0x00000001 0x00000005 0x00000002
+					0x00000004 0x00000001 0x00000003 0x00000008
+					0x00000002 0x00000001 0x00000002 0x00000006
+					0x06020102 0x000a0505 0x73840a06 0x001f0000 >;
+			};
+
+			timing-400000000 {
+				clock-frequency = <400000000>;
+
+				nvidia,emem-configuration = < 0x00000006 0xc0000048
+					0x00000001 0x00000002 0x00000009 0x00000005
+					0x00000007 0x00000001 0x00000002 0x00000008
+					0x00000002 0x00000002 0x00000003 0x00000006
+					0x06030202 0x000d0709 0x7086120a 0x001f0000 >;
+			};
+
+			timing-800000000 {
+				clock-frequency = <800000000>;
+
+				nvidia,emem-configuration = < 0x0000000c 0xc0000090
+					0x00000004 0x00000005 0x00000013 0x0000000c
+					0x0000000f 0x00000002 0x00000003 0x0000000c
+					0x00000002 0x00000002 0x00000004 0x00000008
+					0x08040202 0x00160d13 0x712c2414 0x001f0000 >;
+			};
+		};
+	};
+
+	memory-controller@7000f400 {
+		emc-timings-0 {
+			/* Micron 1GB 800MHZ */
+			nvidia,ram-code = <0>;
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200008>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000001
+					0x00000006 0x00000000 0x00000000 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000000
+					0x00000000 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000005 0x00000004 0x0000000a
+					0x0000000b 0x000000c0 0x00000000 0x00000030
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000007 0x00000007
+					0x00000004 0x00000002 0x00000000 0x00000004
+					0x00000005 0x000000c7 0x00000006 0x00000004
+					0x00000000 0x00000000 0x00004288 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00000000
+					0x00000040 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x80000287 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200008>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000002
+					0x0000000d 0x00000001 0x00000000 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000000
+					0x00000000 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000005 0x00000004 0x0000000a
+					0x0000000b 0x00000181 0x00000000 0x00000060
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x0000000e 0x0000000e
+					0x00000004 0x00000003 0x00000000 0x00000004
+					0x00000005 0x0000018e 0x00000006 0x00000004
+					0x00000000 0x00000000 0x00004288 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00000000
+					0x00000040 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x8000040b 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200008>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000004
+					0x0000001a 0x00000003 0x00000001 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000001
+					0x00000001 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000005 0x00000004 0x0000000a
+					0x0000000b 0x00000303 0x00000000 0x000000c0
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x0000001c 0x0000001c
+					0x00000004 0x00000005 0x00000000 0x00000004
+					0x00000005 0x0000031c 0x00000006 0x00000004
+					0x00000000 0x00000000 0x00004288 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00000000
+					0x00000040 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x80000713 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200008>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000009
+					0x00000035 0x00000007 0x00000002 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000002
+					0x00000002 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000006 0x00000004 0x0000000a
+					0x0000000b 0x00000607 0x00000000 0x00000181
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000038 0x00000038
+					0x00000004 0x00000009 0x00000000 0x00000004
+					0x00000005 0x00000638 0x00000007 0x00000004
+					0x00000000 0x00000000 0x00004288 0x004400a4
+					0x00008000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00020000
+					0x00000100 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x80000d22 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-400000000 {
+				clock-frequency = <400000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100002>;
+				nvidia,emc-mode-2 = <0x80200000>;
+				nvidia,emc-mode-reset = <0x80000521>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+
+				nvidia,emc-configuration =  < 0x00000012
+					0x00000066 0x0000000c 0x00000004 0x00000003
+					0x00000008 0x00000002 0x0000000a 0x00000004
+					0x00000004 0x00000002 0x00000001 0x00000000
+					0x00000004 0x00000006 0x00000004 0x0000000a
+					0x0000000c 0x00000bf0 0x00000000 0x000002fc
+					0x00000001 0x00000008 0x00000001 0x00000000
+					0x00000008 0x0000000f 0x0000006c 0x00000200
+					0x00000004 0x00000010 0x00000000 0x00000004
+					0x00000005 0x00000c30 0x00000000 0x00000004
+					0x00000000 0x00000000 0x00007088 0x001d0084
+					0x00008000 0x00044000 0x00044000 0x00044000
+					0x00044000 0x00014000 0x00014000 0x00014000
+					0x00014000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00048000 0x00048000 0x00048000
+					0x00048000 0x000002a0 0x0600013d 0x00000000
+					0x77fff884 0x01f1f508 0x05057404 0x54000007
+					0x080001e8 0x08000021 0x00000802 0x00020000
+					0x00000100 0x0158000c 0xa0f10000 0x00000000
+					0x00000000 0x800018c8 0xe8000000 0xff00ff89 >;
+			};
+
+			timing-800000000 {
+				clock-frequency = <800000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100002>;
+				nvidia,emc-mode-2 = <0x80200018>;
+				nvidia,emc-mode-reset = <0x80000d71>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000025
+					0x000000ce 0x0000001a 0x00000009 0x00000005
+					0x0000000d 0x00000004 0x00000013 0x00000009
+					0x00000009 0x00000004 0x00000001 0x00000000
+					0x00000007 0x0000000a 0x00000009 0x0000000a
+					0x00000011 0x00001820 0x00000000 0x00000608
+					0x00000003 0x00000012 0x00000001 0x00000000
+					0x0000000f 0x00000018 0x000000d8 0x00000200
+					0x00000005 0x00000020 0x00000000 0x00000007
+					0x00000008 0x00001860 0x0000000b 0x00000006
+					0x00000000 0x00000000 0x00005088 0xf0070191
+					0x00008000 0x0000000a 0x0000000a 0x0000000a
+					0x0000000a 0x0000000a 0x0000000a 0x0000000a
+					0x0000000a 0x00018000 0x00018000 0x00018000
+					0x00018000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x0000000a 0x0000000a 0x0000000a
+					0x0000000a 0x000002a0 0x0800013d 0x22220000
+					0x77fff884 0x01f1f501 0x07077404 0x54000000
+					0x080001e8 0x08000021 0x00000802 0x00020000
+					0x00000100 0x00f0000c 0xa0f10000 0x00000000
+					0x00000000 0x8000308c 0xe8000000 0xff00ff49 >;
+			};
+		};
+
+		emc-timings-1 {
+			/* Elpida 1GB 800MHZ */
+			nvidia,ram-code = <1>;
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200008>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000001
+					0x00000006 0x00000000 0x00000000 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000000
+					0x00000000 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000005 0x00000004 0x0000000a
+					0x0000000b 0x000000c0 0x00000000 0x00000030
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000007 0x00000007
+					0x00000004 0x00000002 0x00000000 0x00000004
+					0x00000005 0x000000c7 0x00000006 0x00000004
+					0x00000000 0x00000000 0x00004288 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00000000
+					0x00000040 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x80000287 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200008>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000002
+					0x0000000d 0x00000001 0x00000000 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000000
+					0x00000000 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000005 0x00000004 0x0000000a
+					0x0000000b 0x00000181 0x00000000 0x00000060
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x0000000e 0x0000000e
+					0x00000004 0x00000003 0x00000000 0x00000004
+					0x00000005 0x0000018e 0x00000006 0x00000004
+					0x00000000 0x00000000 0x00004288 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00000000
+					0x00000040 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x8000040b 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200008>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000004
+					0x0000001a 0x00000003 0x00000001 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000001
+					0x00000001 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000005 0x00000004 0x0000000a
+					0x0000000b 0x00000303 0x00000000 0x000000c0
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x0000001c 0x0000001c
+					0x00000004 0x00000005 0x00000000 0x00000004
+					0x00000005 0x0000031c 0x00000006 0x00000004
+					0x00000000 0x00000000 0x00004288 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00000000
+					0x00000040 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x80000713 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200008>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000009
+					0x00000035 0x00000007 0x00000002 0x00000002
+					0x0000000a 0x00000005 0x0000000b 0x00000002
+					0x00000002 0x00000003 0x00000001 0x00000000
+					0x00000005 0x00000006 0x00000004 0x0000000a
+					0x0000000b 0x00000607 0x00000000 0x00000181
+					0x00000002 0x00000002 0x00000001 0x00000000
+					0x00000007 0x0000000f 0x00000038 0x00000038
+					0x00000004 0x00000009 0x00000000 0x00000004
+					0x00000005 0x00000638 0x00000007 0x00000004
+					0x00000000 0x00000000 0x00004288 0x004400a4
+					0x00008000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x000002a0 0x0800211c 0x00000000
+					0x77fff884 0x01f1f108 0x05057404 0x54000007
+					0x08000168 0x08000000 0x00000802 0x00020000
+					0x00000100 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x80000d22 0xe8000000 0xff00ff00 >;
+			};
+
+			timing-400000000 {
+				clock-frequency = <400000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100002>;
+				nvidia,emc-mode-2 = <0x80200000>;
+				nvidia,emc-mode-reset = <0x80000521>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+
+				nvidia,emc-configuration =  < 0x00000012
+					0x00000066 0x0000000c 0x00000004 0x00000003
+					0x00000008 0x00000002 0x0000000a 0x00000004
+					0x00000004 0x00000002 0x00000001 0x00000000
+					0x00000004 0x00000006 0x00000004 0x0000000a
+					0x0000000c 0x00000bf0 0x00000000 0x000002fc
+					0x00000001 0x00000008 0x00000001 0x00000000
+					0x00000008 0x0000000f 0x0000006c 0x00000200
+					0x00000004 0x00000010 0x00000000 0x00000004
+					0x00000005 0x00000c30 0x00000000 0x00000004
+					0x00000000 0x00000000 0x00007088 0x001d0084
+					0x00008000 0x00044000 0x00044000 0x00044000
+					0x00044000 0x00014000 0x00014000 0x00014000
+					0x00014000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00048000 0x00048000 0x00048000
+					0x00048000 0x000002a0 0x0600013d 0x00000000
+					0x77fff884 0x01f1f508 0x05057404 0x54000007
+					0x080001e8 0x08000021 0x00000802 0x00020000
+					0x00000100 0x0158000c 0xa0f10000 0x00000000
+					0x00000000 0x800018c8 0xe8000000 0xff00ff89 >;
+			};
+
+			timing-800000000 {
+				clock-frequency = <800000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100002>;
+				nvidia,emc-mode-2 = <0x80200018>;
+				nvidia,emc-mode-reset = <0x80000d71>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000025
+					0x000000ce 0x0000001a 0x00000009 0x00000005
+					0x0000000d 0x00000004 0x00000013 0x00000009
+					0x00000009 0x00000004 0x00000001 0x00000000
+					0x00000007 0x0000000a 0x00000009 0x0000000a
+					0x00000011 0x00001820 0x00000000 0x00000608
+					0x00000003 0x00000012 0x00000001 0x00000000
+					0x0000000f 0x00000018 0x000000d8 0x00000200
+					0x00000005 0x00000020 0x00000000 0x00000007
+					0x00000008 0x00001860 0x0000000b 0x00000006
+					0x00000000 0x00000000 0x00005088 0xf0070191
+					0x00008000 0x0000000a 0x0000000a 0x0000000a
+					0x0000000a 0x0000000a 0x0000000a 0x0000000a
+					0x0000000a 0x00018000 0x00018000 0x00018000
+					0x00018000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x0000000a 0x0000000a 0x0000000a
+					0x0000000a 0x000002a0 0x0a00013d 0x22220000
+					0x77fff884 0x01f1f501 0x07077404 0x54000000
+					0x080001e8 0x08000021 0x00000802 0x00020000
+					0x00000100 0x00f0000c 0xa0f10000 0x00000000
+					0x00000000 0x8000308c 0xe8000000 0xff00ff49 >;
+			};
+		};
+	};
+
+	tc358768_refclk: clock-tc358768 {
+		compatible = "fixed-clock";
+		clock-frequency = <23100000>;
+		clock-accuracy = <100>;
+		#clock-cells = <0>;
+	};
+
+	tc358768_osc: clock-tc358768-osc-gate {
+		compatible = "gpio-gate-clock";
+		enable-gpios = <&gpio TEGRA_GPIO(D, 2) GPIO_ACTIVE_HIGH>;
+		clocks = <&tc358768_refclk>;
+		#clock-cells = <0>;
+	};
+
+	haptic-feedback {
+		compatible = "gpio-vibrator";
+		enable-gpios = <&gpio TEGRA_GPIO(H, 7) GPIO_ACTIVE_HIGH>;
+		vcc-supply = <&vdd_3v3_sys>;
+	};
+
+	i2c-mux {
+		compatible = "i2c-mux-gpio";
+
+		mux-gpios = <&gpio TEGRA_GPIO(X, 0) GPIO_ACTIVE_HIGH>;
+		i2c-parent = <&lcd_ddc>;
+		idle-state = <0x0>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		i2c@1 {
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			dsi@7 {
+				compatible = "toshiba,tc358768";
+				reg = <0x7>;
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				clocks = <&tc358768_osc>;
+				clock-names = "refclk";
+
+				reset-gpios = <&gpio TEGRA_GPIO(N, 6) GPIO_ACTIVE_LOW>;
+
+				vddc-supply = <&vdd_1v2_mipi>;
+				vddio-supply = <&vdd_1v8_vio>;
+				vddmipi-supply = <&vdd_1v2_mipi>;
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+
+						bridge_input: endpoint {
+							remote-endpoint = <&dpi_output>;
+							data-lines = <24>;
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+
+						bridge_output: endpoint {
+							remote-endpoint = <&panel_input>;
+						};
+					};
+				};
+
+				/*
+				 * Panasonic VVX10F004B00 or HYDIS HV101WU1-1E1
+				 * LCD SuperIPS+ Full HD panel.
+				 */
+				panel@1 {
+					compatible = "panasonic,vvx10f004b00";
+					reg = <1>;
+
+					power-supply = <&vdd_pnl>;
+					backlight = <&backlight>;
+
+					port {
+						panel_input: endpoint {
+							remote-endpoint = <&bridge_output>;
+						};
+					};
+				};
+			};
+		};
+	};
+
+	vdd_1v2_mipi: regulator-mipi {
+		compatible = "regulator-fixed";
+		regulator-name = "tc358768_1v2_vdd";
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <1200000>;
+		regulator-enable-ramp-delay = <10000>;
+		regulator-boot-on;
+		gpio = <&gpio TEGRA_GPIO(BB, 3) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_3v3_sys>;
+	};
+};
+
+&emc_icc_dvfs_opp_table {
+	/delete-node/ opp-900000000-1350;
+};
+
+&emc_bw_dfs_opp_table {
+	/delete-node/ opp-900000000;
+};
diff --git a/arch/arm/boot/dts/tegra30-asus-transformer-common.dtsi b/arch/arm/boot/dts/tegra30-asus-transformer-common.dtsi
new file mode 100644
index 000000000000..c27e70d8bf2b
--- /dev/null
+++ b/arch/arm/boot/dts/tegra30-asus-transformer-common.dtsi
@@ -0,0 +1,1789 @@
+// SPDX-License-Identifier: GPL-2.0
+
+#include <dt-bindings/input/gpio-keys.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/thermal/thermal.h>
+
+#include "tegra30.dtsi"
+#include "tegra30-cpu-opp.dtsi"
+#include "tegra30-cpu-opp-microvolt.dtsi"
+
+/ {
+	chassis-type = "convertible";
+
+	aliases {
+		mmc0 = "/mmc@78000600"; /* eMMC */
+		mmc1 = "/mmc@78000000"; /* uSD slot */
+		mmc2 = "/mmc@78000400"; /* WiFi */
+
+		rtc0 = &pmic;
+		rtc1 = "/rtc@7000e000";
+
+		display0 = &lcd;
+		display1 = &hdmi;
+
+		serial1 = &uartc; /* Bluetooth */
+		serial2 = &uartb; /* GPS */
+	};
+
+	/*
+	 * The decompressor and also some bootloaders rely on a
+	 * pre-existing /chosen node to be available to insert the
+	 * command line and merge other ATAGS info.
+	 */
+	chosen {};
+
+	memory@80000000 {
+		reg = <0x80000000 0x40000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		linux,cma@80000000 {
+			compatible = "shared-dma-pool";
+			alloc-ranges = <0x80000000 0x30000000>;
+			size = <0x10000000>;		/* 256MiB */
+			linux,cma-default;
+			reusable;
+		};
+
+		ramoops@beb00000 {
+			compatible = "ramoops";
+			reg = <0xbeb00000 0x10000>;	/* 64kB */
+			console-size = <0x8000>;	/* 32kB */
+			record-size = <0x400>;		/*  1kB */
+			ecc-size = <16>;
+		};
+
+		trustzone@bfe00000 {
+			reg = <0xbfe00000 0x200000>;	/* 2MB */
+			no-map;
+		};
+	};
+
+	host1x@50000000 {
+		hdmi: hdmi@54280000 {
+			status = "okay";
+
+			hdmi-supply = <&hdmi_5v0_sys>;
+			pll-supply = <&vdd_1v8_vio>;
+			vdd-supply = <&vdd_3v3_sys>;
+
+			nvidia,hpd-gpio = <&gpio TEGRA_GPIO(N, 7) GPIO_ACTIVE_HIGH>;
+			nvidia,ddc-i2c-bus = <&hdmi_ddc>;
+		};
+	};
+
+	gpio@6000d000 {
+		init-lpm-in-hog {
+			gpio-hog;
+			gpios = <TEGRA_GPIO(I, 6) GPIO_ACTIVE_HIGH>,
+				<TEGRA_GPIO(B, 1) GPIO_ACTIVE_HIGH>;
+			input;
+		};
+
+		init-lpm-out-hog {
+			gpio-hog;
+			gpios = <TEGRA_GPIO(K, 7) GPIO_ACTIVE_HIGH>,
+				<TEGRA_GPIO(R, 0) GPIO_ACTIVE_HIGH>;
+			output-low;
+		};
+
+		usb-charge-limit-hog {
+			gpio-hog;
+			gpios = <TEGRA_GPIO(R, 1) GPIO_ACTIVE_LOW>;
+			output-high;
+		};
+	};
+
+	vde@6001a000 {
+		assigned-clocks = <&tegra_car TEGRA30_CLK_VDE>;
+		assigned-clock-parents = <&tegra_car TEGRA30_CLK_PLL_P>;
+		assigned-clock-rates = <408000000>;
+	};
+
+	pinmux@70000868 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&state_default>;
+
+		state_default: pinmux {
+			/* SDMMC1 pinmux */
+			sdmmc1_clk {
+				nvidia,pins = "sdmmc1_clk_pz0";
+				nvidia,function = "sdmmc1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			sdmmc1_cmd {
+				nvidia,pins = "sdmmc1_dat3_py4",
+						"sdmmc1_dat2_py5",
+						"sdmmc1_dat1_py6",
+						"sdmmc1_dat0_py7",
+						"sdmmc1_cmd_pz1";
+				nvidia,function = "sdmmc1";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			sdmmc1_cd {
+				nvidia,pins = "gmi_iordy_pi5";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			sdmmc1_wp {
+				nvidia,pins = "vi_d11_pt3";
+				nvidia,function = "rsvd2";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* SDMMC2 pinmux */
+			vi_d1_pd5 {
+				nvidia,pins = "vi_d1_pd5",
+						"vi_d2_pl0",
+						"vi_d3_pl1",
+						"vi_d5_pl3",
+						"vi_d7_pl5";
+				nvidia,function = "sdmmc2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			vi_d8_pl6 {
+				nvidia,pins = "vi_d8_pl6",
+						"vi_d9_pl7";
+				nvidia,function = "sdmmc2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,lock = <0>;
+				nvidia,ioreset = <0>;
+			};
+
+			/* SDMMC3 pinmux */
+			sdmmc3_clk {
+				nvidia,pins = "sdmmc3_clk_pa6";
+				nvidia,function = "sdmmc3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			sdmmc3_cmd {
+				nvidia,pins = "sdmmc3_cmd_pa7",
+						"sdmmc3_dat0_pb7",
+						"sdmmc3_dat1_pb6",
+						"sdmmc3_dat2_pb5",
+						"sdmmc3_dat3_pb4",
+						"sdmmc3_dat4_pd1",
+						"sdmmc3_dat5_pd0",
+						"sdmmc3_dat6_pd3",
+						"sdmmc3_dat7_pd4";
+				nvidia,function = "sdmmc3";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* SDMMC4 pinmux */
+			sdmmc4_clk {
+				nvidia,pins = "sdmmc4_clk_pcc4";
+				nvidia,function = "sdmmc4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			sdmmc4_cmd {
+				nvidia,pins = "sdmmc4_cmd_pt7",
+						"sdmmc4_dat0_paa0",
+						"sdmmc4_dat1_paa1",
+						"sdmmc4_dat2_paa2",
+						"sdmmc4_dat3_paa3",
+						"sdmmc4_dat4_paa4",
+						"sdmmc4_dat5_paa5",
+						"sdmmc4_dat6_paa6",
+						"sdmmc4_dat7_paa7";
+				nvidia,function = "sdmmc4";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			sdmmc4_rst_n {
+				nvidia,pins = "sdmmc4_rst_n_pcc3";
+				nvidia,function = "rsvd2";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			cam_mclk {
+				nvidia,pins = "cam_mclk_pcc0";
+				nvidia,function = "vi_alt3";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			drive_sdmmc4 {
+				nvidia,pins = "drive_gma",
+						"drive_gmb",
+						"drive_gmc",
+						"drive_gmd";
+				nvidia,pull-down-strength = <9>;
+				nvidia,pull-up-strength = <9>;
+				nvidia,slew-rate-rising = <TEGRA_PIN_SLEW_RATE_SLOWEST>;
+				nvidia,slew-rate-falling = <TEGRA_PIN_SLEW_RATE_SLOWEST>;
+			};
+
+			/* I2C pinmux */
+			gen1_i2c {
+				nvidia,pins = "gen1_i2c_scl_pc4",
+						"gen1_i2c_sda_pc5";
+				nvidia,function = "i2c1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,open-drain = <TEGRA_PIN_ENABLE>;
+				nvidia,lock = <0>;
+			};
+
+			gen2_i2c {
+				nvidia,pins = "gen2_i2c_scl_pt5",
+						"gen2_i2c_sda_pt6";
+				nvidia,function = "i2c2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,open-drain = <TEGRA_PIN_ENABLE>;
+				nvidia,lock = <0>;
+			};
+
+			cam_i2c {
+				nvidia,pins = "cam_i2c_scl_pbb1",
+						"cam_i2c_sda_pbb2";
+				nvidia,function = "i2c3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,open-drain = <TEGRA_PIN_ENABLE>;
+				nvidia,lock = <0>;
+			};
+
+			ddc_i2c {
+				nvidia,pins = "ddc_scl_pv4",
+						"ddc_sda_pv5";
+				nvidia,function = "i2c4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,lock = <0>;
+			};
+
+			pwr_i2c {
+				nvidia,pins = "pwr_i2c_scl_pz6",
+						"pwr_i2c_sda_pz7";
+				nvidia,function = "i2cpwr";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,open-drain = <TEGRA_PIN_ENABLE>;
+				nvidia,lock = <0>;
+			};
+
+			hotplug_i2c {
+				nvidia,pins = "pu4";
+				nvidia,function = "rsvd4";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* HDMI pinmux */
+			hdmi_cec {
+				nvidia,pins = "hdmi_cec_pee3";
+				nvidia,function = "cec";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,open-drain = <TEGRA_PIN_ENABLE>;
+				nvidia,lock = <0>;
+			};
+
+			hdmi_hpd {
+				nvidia,pins = "hdmi_int_pn7";
+				nvidia,function = "hdmi";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* UART-A */
+			ulpi_data0_po1 {
+				nvidia,pins = "ulpi_data0_po1";
+				nvidia,function = "uarta";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			ulpi_data1_po2 {
+				nvidia,pins = "ulpi_data1_po2";
+				nvidia,function = "uarta";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			ulpi_data5_po6 {
+				nvidia,pins = "ulpi_data5_po6";
+				nvidia,function = "uarta";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			ulpi_data7_po0 {
+				nvidia,pins = "ulpi_data7_po0",
+						"ulpi_data2_po3",
+						"ulpi_data3_po4",
+						"ulpi_data4_po5",
+						"ulpi_data6_po7";
+				nvidia,function = "uarta";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* UART-B */
+			uartb_txd_rts {
+				nvidia,pins = "uart2_txd_pc2",
+						"uart2_rts_n_pj6";
+				nvidia,function = "uartb";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			uartb_rxd_cts {
+				nvidia,pins = "uart2_rxd_pc3",
+						"uart2_cts_n_pj5";
+				nvidia,function = "uartb";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* UART-C */
+			uartc_rxd_cts {
+				nvidia,pins = "uart3_cts_n_pa1",
+						"uart3_rxd_pw7";
+				nvidia,function = "uartc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			uartc_txd_rts {
+				nvidia,pins = "uart3_rts_n_pc0",
+						"uart3_txd_pw6";
+				nvidia,function = "uartc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			/* UART-D */
+			ulpi_nxt_py2 {
+				nvidia,pins = "ulpi_nxt_py2";
+				nvidia,function = "uartd";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			ulpi_clk_py0 {
+				nvidia,pins = "ulpi_clk_py0",
+						"ulpi_dir_py1",
+						"ulpi_stp_py3";
+				nvidia,function = "uartd";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			/* I2S pinmux */
+			dap_i2s0 {
+				nvidia,pins = "dap1_fs_pn0",
+						"dap1_din_pn1",
+						"dap1_dout_pn2",
+						"dap1_sclk_pn3";
+				nvidia,function = "i2s0";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			dap_i2s1 {
+				nvidia,pins = "dap2_fs_pa2",
+						"dap2_sclk_pa3",
+						"dap2_din_pa4",
+						"dap2_dout_pa5";
+				nvidia,function = "i2s1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			dap3_fs {
+				nvidia,pins = "dap3_fs_pp0",
+						"dap3_din_pp1";
+				nvidia,function = "i2s2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			dap3_dout {
+				nvidia,pins = "dap3_dout_pp2",
+						"dap3_sclk_pp3";
+				nvidia,function = "i2s2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			dap_i2s3 {
+				nvidia,pins = "dap4_fs_pp4",
+						"dap4_din_pp5",
+						"dap4_dout_pp6",
+						"dap4_sclk_pp7";
+				nvidia,function = "i2s3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* Sensors pinmux */
+			nct_irq {
+				nvidia,pins = "pcc2";
+				nvidia,function = "i2s4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* Asus EC pinmux */
+			ec_irqs {
+				nvidia,pins = "kb_row10_ps2",
+						"kb_row15_ps7";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			ec_reqs {
+				nvidia,pins = "kb_col1_pq1";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* Memory type bootstrap */
+			mem_boostraps {
+				nvidia,pins = "gmi_ad4_pg4",
+						"gmi_ad5_pg5";
+				nvidia,function = "nand";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* PCI-e pinmux */
+			pex_l2_rst_n {
+				nvidia,pins = "pex_l2_rst_n_pcc6",
+						"pex_l0_rst_n_pdd1",
+						"pex_l1_rst_n_pdd5";
+				nvidia,function = "pcie";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pex_l2_clkreq_n {
+				nvidia,pins = "pex_l2_clkreq_n_pcc7",
+						"pex_l0_prsnt_n_pdd0",
+						"pex_l0_clkreq_n_pdd2",
+						"pex_wake_n_pdd3",
+						"pex_l1_prsnt_n_pdd4",
+						"pex_l1_clkreq_n_pdd6",
+						"pex_l2_prsnt_n_pdd7";
+				nvidia,function = "pcie";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* SPI pinmux */
+			spi1_mosi_px4 {
+				nvidia,pins = "spi1_mosi_px4",
+						"spi1_sck_px5",
+						"spi1_cs0_n_px6",
+						"spi1_miso_px7";
+				nvidia,function = "spi1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			spi2_cs1_n_pw2 {
+				nvidia,pins = "spi2_cs1_n_pw2";
+				nvidia,function = "spi2";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			spi2_sck_px2 {
+				nvidia,pins = "spi2_sck_px2";
+				nvidia,function = "spi2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			gmi_a17_pb0 {
+				nvidia,pins = "gmi_a17_pb0",
+						"gmi_a16_pj7";
+				nvidia,function = "spi4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			gmi_a18_pb1 {
+				nvidia,pins = "gmi_a18_pb1";
+				nvidia,function = "spi4";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			gmi_a19_pk7 {
+				nvidia,pins = "gmi_a19_pk7";
+				nvidia,function = "spi4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* Display A pinmux */
+			lcd_pwr0_pb2 {
+				nvidia,pins = "lcd_pwr0_pb2",
+						"lcd_pclk_pb3",
+						"lcd_pwr1_pc1",
+						"lcd_d0_pe0",
+						"lcd_d1_pe1",
+						"lcd_d2_pe2",
+						"lcd_d3_pe3",
+						"lcd_d4_pe4",
+						"lcd_d5_pe5",
+						"lcd_d6_pe6",
+						"lcd_d7_pe7",
+						"lcd_d8_pf0",
+						"lcd_d9_pf1",
+						"lcd_d10_pf2",
+						"lcd_d11_pf3",
+						"lcd_d12_pf4",
+						"lcd_d13_pf5",
+						"lcd_d14_pf6",
+						"lcd_d15_pf7",
+						"lcd_de_pj1",
+						"lcd_hsync_pj3",
+						"lcd_vsync_pj4",
+						"lcd_d16_pm0",
+						"lcd_d17_pm1",
+						"lcd_d18_pm2",
+						"lcd_d19_pm3",
+						"lcd_d20_pm4",
+						"lcd_d21_pm5",
+						"lcd_d22_pm6",
+						"lcd_d23_pm7",
+						"lcd_dc0_pn6",
+						"lcd_sdin_pz2";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			lcd_cs0_n_pn4 {
+				nvidia,pins = "lcd_cs0_n_pn4",
+						"lcd_sdout_pn5",
+						"lcd_wr_n_pz3";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			blink {
+				nvidia,pins = "clk_32k_out_pa0";
+				nvidia,function = "blink";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			/* KBC keys */
+			kb_col0_pq0 {
+				nvidia,pins = "kb_col0_pq0";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			kb_col1_pq1 {
+				nvidia,pins = "kb_row1_pr1",
+						"kb_row3_pr3",
+						"kb_row8_ps0",
+						"kb_row14_ps6";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			kb_col4_pq4 {
+				nvidia,pins = "kb_col4_pq4",
+						"kb_col5_pq5",
+						"kb_col7_pq7",
+						"kb_row2_pr2",
+						"kb_row4_pr4",
+						"kb_row5_pr5",
+						"kb_row12_ps4",
+						"kb_row13_ps5";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			gmi_wp_n_pc7 {
+				nvidia,pins = "gmi_wp_n_pc7",
+						"gmi_wait_pi7",
+						"gmi_cs3_n_pk4";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			gmi_cs0_n_pj0 {
+				nvidia,pins = "gmi_cs0_n_pj0",
+						"gmi_cs1_n_pj2",
+						"gmi_cs2_n_pk3";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			vi_pclk_pt0 {
+				nvidia,pins = "vi_pclk_pt0";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,lock = <0>;
+				nvidia,ioreset = <0>;
+			};
+
+			/* GPIO keys pinmux */
+			power_key {
+				nvidia,pins = "pv0";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			vol_keys {
+				nvidia,pins = "kb_col2_pq2",
+						"kb_col3_pq3";
+				nvidia,function = "rsvd4";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* Bluetooth */
+			bt_shutdown {
+				nvidia,pins = "pu0";
+				nvidia,function = "rsvd4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			bt_dev_wake {
+				nvidia,pins = "pu1";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			bt_host_wake {
+				nvidia,pins = "pu6";
+				nvidia,function = "rsvd4";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			pu2 {
+				nvidia,pins = "pu2";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			pu3 {
+				nvidia,pins = "pu3";
+				nvidia,function = "rsvd4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pcc1 {
+				nvidia,pins = "pcc1";
+				nvidia,function = "rsvd2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			pv2 {
+				nvidia,pins = "pv2";
+				nvidia,function = "rsvd2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pv3 {
+				nvidia,pins = "pv3";
+				nvidia,function = "rsvd2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			vi_vsync_pd6 {
+				nvidia,pins = "vi_vsync_pd6",
+						"vi_hsync_pd7";
+				nvidia,function = "rsvd2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,lock = <0>;
+				nvidia,ioreset = <0>;
+			};
+
+			vi_d10_pt2 {
+				nvidia,pins = "vi_d10_pt2",
+						"vi_d0_pt4", "pbb0";
+				nvidia,function = "rsvd2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			kb_row0_pr0 {
+				nvidia,pins = "kb_row0_pr0";
+				nvidia,function = "rsvd4";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			gmi_ad0_pg0 {
+				nvidia,pins = "gmi_ad0_pg0",
+						"gmi_ad1_pg1",
+						"gmi_ad2_pg2",
+						"gmi_ad3_pg3",
+						"gmi_ad6_pg6",
+						"gmi_ad7_pg7",
+						"gmi_wr_n_pi0",
+						"gmi_oe_n_pi1",
+						"gmi_dqs_pi2",
+						"gmi_adv_n_pk0",
+						"gmi_clk_pk1";
+				nvidia,function = "nand";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			gmi_ad13_ph5 {
+				nvidia,pins = "gmi_ad13_ph5";
+				nvidia,function = "nand";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			gmi_ad10_ph2 {
+				nvidia,pins = "gmi_ad10_ph2",
+						"gmi_ad11_ph3",
+						"gmi_ad14_ph6";
+				nvidia,function = "nand";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			gmi_ad12_ph4 {
+				nvidia,pins = "gmi_ad12_ph4",
+						"gmi_rst_n_pi4",
+						"gmi_cs7_n_pi6";
+				nvidia,function = "nand";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* Vibrator control */
+			vibrator {
+				nvidia,pins = "gmi_ad15_ph7";
+				nvidia,function = "nand";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			/* PWM pimnmux */
+			pwm_0 {
+				nvidia,pins = "gmi_ad8_ph0";
+				nvidia,function = "pwm0";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pwm_2 {
+				nvidia,pins = "pu5";
+				nvidia,function = "pwm2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			gmi_cs6_n_pi3 {
+				nvidia,pins = "gmi_cs6_n_pi3";
+				nvidia,function = "gmi";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			/* Spdif pinmux */
+			spdif_out {
+				nvidia,pins = "spdif_out_pk5";
+				nvidia,function = "spdif";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			spdif_in {
+				nvidia,pins = "spdif_in_pk6";
+				nvidia,function = "spdif";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			vi_d4_pl2 {
+				nvidia,pins = "vi_d4_pl2";
+				nvidia,function = "vi";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			vi_d6_pl4 {
+				nvidia,pins = "vi_d6_pl4";
+				nvidia,function = "vi";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+				nvidia,lock = <0>;
+				nvidia,ioreset = <0>;
+			};
+
+			vi_mclk_pt1 {
+				nvidia,pins = "vi_mclk_pt1";
+				nvidia,function = "vi";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			jtag_rtck {
+				nvidia,pins = "jtag_rtck_pu7";
+				nvidia,function = "rtck";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			crt_hsync_pv6 {
+				nvidia,pins = "crt_hsync_pv6",
+						"crt_vsync_pv7";
+				nvidia,function = "crt";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			clk1_out {
+				nvidia,pins = "clk1_out_pw4";
+				nvidia,function = "extperiph1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			clk2_out {
+				nvidia,pins = "clk2_out_pw5";
+				nvidia,function = "extperiph2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			clk3_out {
+				nvidia,pins = "clk3_out_pee0";
+				nvidia,function = "extperiph3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			sys_clk_req {
+				nvidia,pins = "sys_clk_req_pz5";
+				nvidia,function = "sysclk";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pbb4 {
+				nvidia,pins = "pbb4";
+				nvidia,function = "vgp4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			pbb5 {
+				nvidia,pins = "pbb5";
+				nvidia,function = "vgp5";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			pbb6 {
+				nvidia,pins = "pbb6";
+				nvidia,function = "vgp6";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			clk2_req_pcc5 {
+				nvidia,pins = "clk2_req_pcc5",
+						"clk1_req_pee2";
+				nvidia,function = "dap";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			clk3_req_pee1 {
+				nvidia,pins = "clk3_req_pee1";
+				nvidia,function = "dev3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			owr {
+				nvidia,pins = "owr";
+				nvidia,function = "owr";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* GPIO power/drive control */
+			drive_dap1 {
+				nvidia,pins = "drive_dap1",
+						"drive_dap2",
+						"drive_dbg",
+						"drive_at5",
+						"drive_gme",
+						"drive_ddc",
+						"drive_ao1",
+						"drive_uart3";
+				nvidia,high-speed-mode = <TEGRA_PIN_DISABLE>;
+				nvidia,schmitt = <TEGRA_PIN_ENABLE>;
+				nvidia,low-power-mode = <TEGRA_PIN_LP_DRIVE_DIV_1>;
+				nvidia,pull-down-strength = <31>;
+				nvidia,pull-up-strength = <31>;
+				nvidia,slew-rate-rising = <TEGRA_PIN_SLEW_RATE_FASTEST>;
+				nvidia,slew-rate-falling = <TEGRA_PIN_SLEW_RATE_FASTEST>;
+			};
+
+			drive_sdio1 {
+				nvidia,pins = "drive_sdio1",
+						"drive_sdio3";
+				nvidia,high-speed-mode = <TEGRA_PIN_DISABLE>;
+				nvidia,schmitt = <TEGRA_PIN_DISABLE>;
+				nvidia,pull-down-strength = <46>;
+				nvidia,pull-up-strength = <42>;
+				nvidia,slew-rate-rising = <TEGRA_PIN_SLEW_RATE_FAST>;
+				nvidia,slew-rate-falling = <TEGRA_PIN_SLEW_RATE_FAST>;
+			};
+		};
+	};
+
+	serial@70006040 {
+		compatible = "nvidia,tegra30-hsuart";
+		/delete-property/ reg-shift;
+		status = "okay";
+
+		/* Broadcom GPS BCM47511 */
+	};
+
+	serial@70006200 {
+		compatible = "nvidia,tegra30-hsuart";
+		/delete-property/ reg-shift;
+		status = "okay";
+
+		nvidia,adjust-baud-rates = <0 9600 100>,
+					   <9600 115200 200>,
+					   <1000000 4000000 136>;
+
+		bluetooth {
+			max-speed = <4000000>;
+
+			clocks = <&tegra_pmc TEGRA_PMC_CLK_BLINK>;
+			clock-names = "txco";
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(U, 6) IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "host-wakeup";
+
+			device-wakeup-gpios = <&gpio TEGRA_GPIO(U, 1) GPIO_ACTIVE_HIGH>;
+			shutdown-gpios =      <&gpio TEGRA_GPIO(U, 0) GPIO_ACTIVE_HIGH>;
+
+			vbat-supply  = <&vdd_3v3_com>;
+			vddio-supply = <&vdd_1v8_vio>;
+		};
+	};
+
+	pwm@7000a000 {
+		status = "okay";
+	};
+
+	lcd_ddc: i2c@7000c000 {
+		status = "okay";
+		clock-frequency = <100000>;
+	};
+
+	i2c@7000c400 {
+		status = "okay";
+		clock-frequency = <400000>;
+	};
+
+	i2c@7000c500 {
+		status = "okay";
+
+		/* Aichi AMI306 digital compass */
+		magnetometer@e {
+			compatible = "asahi-kasei,ak8974";
+			reg = <0x0e>;
+
+			avdd-supply = <&vdd_3v3_sys>;
+			dvdd-supply = <&vdd_1v8_vio>;
+		};
+
+		/* Dynaimage ambient light sensor */
+		light-sensor@1c {
+			compatible = "dynaimage,al3010";
+			reg = <0x1c>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(Z, 2) IRQ_TYPE_LEVEL_HIGH>;
+
+			vdd-supply = <&vdd_3v3_sys>;
+		};
+
+		gyroscope@68 {
+			compatible = "invensense,mpu3050";
+			reg = <0x68>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(X, 1) IRQ_TYPE_EDGE_RISING>;
+
+			vdd-supply    = <&vdd_3v3_sys>;
+			vlogic-supply = <&vdd_1v8_vio>;
+
+			i2c-gate {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				accelerometer@f {
+					compatible = "kionix,kxtf9";
+					reg = <0x0f>;
+
+					interrupt-parent = <&gpio>;
+					interrupts = <TEGRA_GPIO(O, 5) IRQ_TYPE_EDGE_RISING>;
+
+					vdd-supply = <&vdd_1v8_vio>;
+					vddio-supply = <&vdd_1v8_vio>;
+				};
+			};
+		};
+	};
+
+	hdmi_ddc: i2c@7000c700 {
+		status = "okay";
+		clock-frequency = <93750>;
+	};
+
+	i2c@7000d000 {
+		status = "okay";
+		clock-frequency = <400000>;
+
+		nct72: temperature-sensor@4c {
+			compatible = "onnn,nct1008";
+			reg = <0x4c>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(CC, 2) IRQ_TYPE_EDGE_FALLING>;
+
+			vcc-supply = <&vdd_3v3_sys>;
+			#thermal-sensor-cells = <1>;
+		};
+
+		/* Texas Instruments TPS659110 PMIC */
+		pmic: pmic@2d {
+			compatible = "ti,tps65911";
+			reg = <0x2d>;
+
+			interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
+			#interrupt-cells = <2>;
+			interrupt-controller;
+			wakeup-source;
+
+			ti,en-gpio-sleep = <0 0 1 0 0 0 0 0 0>;
+			ti,system-power-controller;
+			ti,sleep-keep-ck32k;
+			ti,sleep-enable;
+
+			#gpio-cells = <2>;
+			gpio-controller;
+
+			vcc1-supply = <&vdd_5v0_bat>;
+			vcc2-supply = <&vdd_5v0_bat>;
+			vcc3-supply = <&vdd_1v8_vio>;
+			vcc4-supply = <&vdd_5v0_sys>;
+			vcc5-supply = <&vdd_5v0_bat>;
+			vcc6-supply = <&vdd_3v3_sys>;
+			vcc7-supply = <&vdd_5v0_bat>;
+			vccio-supply = <&vdd_5v0_bat>;
+
+			pmic-sleep-hog {
+				gpio-hog;
+				gpios = <2 GPIO_ACTIVE_HIGH>;
+				output-high;
+			};
+
+			regulators {
+				/* VDD1 is not used by Transformers */
+
+				vddio_ddr: vdd2 {
+					regulator-name = "vddio_ddr";
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				vdd_cpu: vddctrl {
+					regulator-name = "vdd_cpu,vdd_sys";
+					regulator-min-microvolt = <600000>;
+					regulator-max-microvolt = <1400000>;
+					regulator-coupled-with = <&vdd_core>;
+					regulator-coupled-max-spread = <300000>;
+					regulator-max-step-microvolt = <100000>;
+					regulator-always-on;
+					regulator-boot-on;
+					ti,regulator-ext-sleep-control = <1>;
+
+					nvidia,tegra-cpu-regulator;
+				};
+
+				vdd_1v8_vio: vio {
+					regulator-name = "vdd_1v8_gen";
+					/* FIXME: eMMC won't work, if set to 1.8 V */
+					regulator-min-microvolt = <1500000>;
+					regulator-max-microvolt = <3300000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				/* eMMC VDD */
+				vcore_emmc: ldo1 {
+					regulator-name = "vdd_emmc_core";
+					regulator-min-microvolt = <3300000>;
+					regulator-max-microvolt = <3300000>;
+					regulator-always-on;
+				};
+
+				/* uSD slot VDD */
+				vdd_usd: ldo2 {
+					regulator-name = "vdd_usd";
+					regulator-min-microvolt = <3100000>;
+					regulator-max-microvolt = <3100000>;
+					/* FIXME: Without this, voltage switching fails */
+					regulator-always-on;
+				};
+
+				/* uSD slot VDDIO */
+				vddio_usd: ldo3 {
+					regulator-name = "vddio_usd";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <3100000>;
+				};
+
+				ldo4 {
+					regulator-name = "vdd_rtc";
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+					regulator-always-on;
+				};
+
+				/* LDO5 is not used by Transformers */
+
+				ldo6 {
+					regulator-name = "avdd_dsi_csi,pwrdet_mipi";
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+				};
+
+				ldo7 {
+					regulator-name = "vdd_pllm,x,u,a_p_c_s";
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+					regulator-always-on;
+					regulator-boot-on;
+					ti,regulator-ext-sleep-control = <8>;
+				};
+
+				ldo8 {
+					regulator-name = "vdd_ddr_hs";
+					regulator-min-microvolt = <1000000>;
+					regulator-max-microvolt = <1000000>;
+					regulator-always-on;
+					ti,regulator-ext-sleep-control = <8>;
+				};
+			};
+		};
+
+		vdd_core: core-regulator@60 {
+			compatible = "ti,tps62361";
+			reg = <0x60>;
+
+			regulator-name = "tps62361-vout";
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1770000>;
+			regulator-coupled-with = <&vdd_cpu>;
+			regulator-coupled-max-spread = <300000>;
+			regulator-max-step-microvolt = <100000>;
+			regulator-boot-on;
+			regulator-always-on;
+			ti,enable-vout-discharge;
+			ti,vsel0-state-high;
+			ti,vsel1-state-high;
+
+			nvidia,tegra-core-regulator;
+		};
+	};
+
+	pmc@7000e400 {
+		status = "okay";
+		nvidia,invert-interrupt;
+		/* FIXME: LP1 doesn't work at the moment */
+		nvidia,suspend-mode = <2>;
+		nvidia,cpu-pwr-good-time = <2000>;
+		nvidia,cpu-pwr-off-time = <200>;
+		nvidia,core-pwr-good-time = <3845 3845>;
+		nvidia,core-pwr-off-time = <0>;
+		nvidia,core-power-req-active-high;
+		nvidia,sys-clock-req-active-high;
+		core-supply = <&vdd_core>;
+
+		/* Set DEV_OFF + PWR_OFF_SET bit in DCDC control register of TPS65911 PMIC  */
+		i2c-thermtrip {
+			nvidia,i2c-controller-id = <4>;
+			nvidia,bus-addr = <0x2d>;
+			nvidia,reg-addr = <0x3f>;
+			nvidia,reg-data = <0x81>;
+		};
+	};
+
+	hda@70030000 {
+		status = "okay";
+	};
+
+	ahub@70080000 {
+		i2s@70080400 {		/* i2s1 */
+			status = "okay";
+		};
+
+		/* BT SCO */
+		i2s@70080600 {		/* i2s3 */
+			status = "okay";
+		};
+	};
+
+	mmc@78000000 {
+		status = "okay";
+
+		/* FIXME: Full 208Mhz clock rate doesn't work reliably */
+		max-frequency = <104000000>;
+
+		cd-gpios = <&gpio TEGRA_GPIO(I, 5) GPIO_ACTIVE_LOW>;
+		bus-width = <4>;
+
+		vmmc-supply = <&vdd_usd>;	/* ldo2 */
+		vqmmc-supply = <&vddio_usd>;	/* ldo3 */
+	};
+
+	mmc@78000400 {
+		status = "okay";
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		assigned-clocks = <&tegra_car TEGRA30_CLK_SDMMC3>;
+		assigned-clock-parents = <&tegra_car TEGRA30_CLK_PLL_C>;
+		assigned-clock-rates = <50000000>;
+
+		max-frequency = <50000000>;
+		keep-power-in-suspend;
+		bus-width = <4>;
+		non-removable;
+
+		mmc-pwrseq = <&brcm_wifi_pwrseq>;
+		vmmc-supply = <&vdd_3v3_com>;
+		vqmmc-supply = <&vdd_1v8_vio>;
+
+		/* Azurewave AW-NH615 BCM4329B1 or AW-NH665 BCM4330B1 */
+		wifi@1 {
+			compatible = "brcm,bcm4329-fmac";
+			reg = <1>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(O, 4) IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "host-wake";
+		};
+	};
+
+	mmc@78000600 {
+		status = "okay";
+		bus-width = <8>;
+		vmmc-supply = <&vcore_emmc>;
+		vqmmc-supply = <&vdd_1v8_vio>;
+		mmc-ddr-3_3v;
+		non-removable;
+	};
+
+	/* USB via ASUS connector */
+	usb@7d000000 {
+		compatible = "nvidia,tegra30-udc";
+		status = "okay";
+		dr_mode = "peripheral";
+	};
+
+	usb-phy@7d000000 {
+		status = "okay";
+		dr_mode = "peripheral";
+		nvidia,hssync-start-delay = <0>;
+		nvidia,xcvr-lsfslew = <2>;
+		nvidia,xcvr-lsrslew = <2>;
+		vbus-supply = <&vdd_5v0_sys>;
+	};
+
+	/* Dock's USB port */
+	usb@7d008000 {
+		status = "okay";
+	};
+
+	usb-phy@7d008000 {
+		status = "okay";
+		vbus-supply = <&vdd_5v0_bat>;
+	};
+
+	mains: ac-adapter-detect {
+		compatible = "gpio-charger";
+		charger-type = "mains";
+		gpios = <&gpio TEGRA_GPIO(H, 5) GPIO_ACTIVE_HIGH>;
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+
+		enable-gpios = <&gpio TEGRA_GPIO(H, 2) GPIO_ACTIVE_HIGH>;
+		power-supply = <&vdd_5v0_bl>;
+		pwms = <&pwm 0 4000000>;
+
+		brightness-levels = <1 255>;
+		num-interpolated-steps = <254>;
+		default-brightness-level = <40>;
+	};
+
+	/* PMIC has a built-in 32KHz oscillator which is used by PMC */
+	clk32k_in: clock-32k {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		clock-output-names = "pmic-oscillator";
+	};
+
+	cpus {
+		cpu0: cpu@0 {
+			cpu-supply = <&vdd_cpu>;
+			operating-points-v2 = <&cpu0_opp_table>;
+			#cooling-cells = <2>;
+		};
+		cpu1: cpu@1 {
+			cpu-supply = <&vdd_cpu>;
+			operating-points-v2 = <&cpu0_opp_table>;
+			#cooling-cells = <2>;
+		};
+		cpu2: cpu@2 {
+			cpu-supply = <&vdd_cpu>;
+			operating-points-v2 = <&cpu0_opp_table>;
+			#cooling-cells = <2>;
+		};
+		cpu3: cpu@3 {
+			cpu-supply = <&vdd_cpu>;
+			operating-points-v2 = <&cpu0_opp_table>;
+			#cooling-cells = <2>;
+		};
+	};
+
+	extcon-keys {
+		compatible = "gpio-keys";
+		interrupt-parent = <&gpio>;
+
+		switch-dock-hall-sensor {
+			label = "Lid sensor";
+			gpios = <&gpio TEGRA_GPIO(S, 6) GPIO_ACTIVE_LOW>;
+			linux,input-type = <EV_SW>;
+			linux,code = <SW_LID>;
+			debounce-interval = <500>;
+			wakeup-event-action = <EV_ACT_ASSERTED>;
+			wakeup-source;
+		};
+
+		switch-lineout-detect {
+			label = "Audio dock line-out detect";
+			gpios = <&gpio TEGRA_GPIO(X, 3) GPIO_ACTIVE_LOW>;
+			linux,input-type = <EV_SW>;
+			linux,code = <SW_LINEOUT_INSERT>;
+			debounce-interval = <10>;
+			wakeup-event-action = <EV_ACT_ASSERTED>;
+			wakeup-source;
+		};
+	};
+
+	firmware {
+		trusted-foundations {
+			compatible = "tlm,trusted-foundations";
+			tlm,version-major = <2>;
+			tlm,version-minor = <8>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		interrupt-parent = <&gpio>;
+
+		key-power {
+			label = "Power";
+			gpios = <&gpio TEGRA_GPIO(V, 0) GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_POWER>;
+			debounce-interval = <10>;
+			wakeup-event-action = <EV_ACT_ASSERTED>;
+			wakeup-source;
+		};
+
+		key-volume-up {
+			label = "Volume Up";
+			gpios = <&gpio TEGRA_GPIO(Q, 2) GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+			debounce-interval = <10>;
+			wakeup-event-action = <EV_ACT_ASSERTED>;
+			wakeup-source;
+		};
+
+		key-volume-down {
+			label = "Volume Down";
+			gpios = <&gpio TEGRA_GPIO(Q, 3) GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEDOWN>;
+			debounce-interval = <10>;
+			wakeup-event-action = <EV_ACT_ASSERTED>;
+			wakeup-source;
+		};
+	};
+
+	vdd_5v0_bat: regulator-bat {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_ac_bat";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vdd_5v0_cp: regulator-sby {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_5v0_sby";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		regulator-boot-on;
+		gpio = <&pmic 0 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_5v0_bat>;
+	};
+
+	vdd_5v0_sys: regulator-5v {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_5v0_sys";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		regulator-boot-on;
+		gpio = <&pmic 8 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_5v0_bat>;
+	};
+
+	vdd_1v5_ddr: regulator-ddr {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_ddr";
+		regulator-min-microvolt = <1500000>;
+		regulator-max-microvolt = <1500000>;
+		regulator-always-on;
+		regulator-boot-on;
+		gpio = <&pmic 7 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_5v0_bat>;
+	};
+
+	vdd_3v3_sys: regulator-3v {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_3v3_sys";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		regulator-boot-on;
+		gpio = <&pmic 6 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_5v0_bat>;
+	};
+
+	vdd_pnl: regulator-panel {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_panel";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-enable-ramp-delay = <20000>;
+		gpio = <&gpio TEGRA_GPIO(W, 1) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_3v3_sys>;
+	};
+
+	vdd_3v3_com: regulator-com {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_3v3_com";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		gpio = <&gpio TEGRA_GPIO(D, 0) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_3v3_sys>;
+	};
+
+	vdd_5v0_bl: regulator-bl {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_5v0_bl";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-boot-on;
+		gpio = <&gpio TEGRA_GPIO(H, 3) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_5v0_bat>;
+	};
+
+	hdmi_5v0_sys: regulator-hdmi {
+		compatible = "regulator-fixed";
+		regulator-name = "hdmi_5v0_sys";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio TEGRA_GPIO(P, 2) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_5v0_sys>;
+	};
+
+	sound {
+		nvidia,i2s-controller = <&tegra_i2s1>;
+
+		nvidia,hp-det-gpios = <&gpio TEGRA_GPIO(W, 2) GPIO_ACTIVE_LOW>;
+		nvidia,hp-mute-gpios = <&gpio TEGRA_GPIO(X, 2) GPIO_ACTIVE_LOW>;
+
+		clocks = <&tegra_car TEGRA30_CLK_PLL_A>,
+			 <&tegra_car TEGRA30_CLK_PLL_A_OUT0>,
+			 <&tegra_pmc TEGRA_PMC_CLK_OUT_1>;
+		clock-names = "pll_a", "pll_a_out0", "mclk";
+
+		assigned-clocks = <&tegra_car TEGRA30_CLK_EXTERN1>,
+				  <&tegra_pmc TEGRA_PMC_CLK_OUT_1>;
+
+		assigned-clock-parents = <&tegra_car TEGRA30_CLK_PLL_A_OUT0>,
+					 <&tegra_car TEGRA30_CLK_EXTERN1>;
+	};
+
+	thermal-zones {
+		/*
+		 * NCT72 has two sensors:
+		 *
+		 *	0: internal that monitors ambient/skin temperature
+		 *	1: external that is connected to the CPU's diode
+		 *
+		 * Ideally we should use userspace thermal governor,
+		 * but it's a much more complex solution.  The "skin"
+		 * zone exists as a simpler solution which prevents
+		 * Transformers from getting too hot from a user's
+		 * tactile perspective. The CPU zone is intended to
+		 * protect silicon from damage.
+		 */
+
+		skin-thermal {
+			polling-delay-passive = <1000>; /* milliseconds */
+			polling-delay = <5000>; /* milliseconds */
+
+			thermal-sensors = <&nct72 0>;
+
+			trips {
+				trip0: skin-alert {
+					/* throttle at 57C until temperature drops to 56.8C */
+					temperature = <57000>;
+					hysteresis = <200>;
+					type = "passive";
+				};
+
+				trip1: skin-crit {
+					/* shut down at 65C */
+					temperature = <65000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				map0 {
+					trip = <&trip0>;
+					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&actmon THERMAL_NO_LIMIT
+								  THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+
+		cpu-thermal {
+			polling-delay-passive = <1000>; /* milliseconds */
+			polling-delay = <5000>; /* milliseconds */
+
+			thermal-sensors = <&nct72 1>;
+
+			trips {
+				trip2: cpu-alert {
+					/* throttle at 75C until temperature drops to 74.8C */
+					temperature = <75000>;
+					hysteresis = <200>;
+					type = "passive";
+				};
+
+				trip3: cpu-crit {
+					/* shut down at 90C */
+					temperature = <90000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				map1 {
+					trip = <&trip2>;
+					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&actmon THERMAL_NO_LIMIT
+								  THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+	};
+
+	brcm_wifi_pwrseq: wifi-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+
+		clocks = <&tegra_pmc TEGRA_PMC_CLK_BLINK>;
+		clock-names = "ext_clock";
+
+		reset-gpios = <&gpio TEGRA_GPIO(D, 4) GPIO_ACTIVE_LOW>;
+		post-power-on-delay-ms = <300>;
+		power-off-delay-us = <300>;
+	};
+};
diff --git a/arch/arm/boot/dts/tegra30-beaver.dts b/arch/arm/boot/dts/tegra30-beaver.dts
index e159feeedef7..5ad62b567d32 100644
--- a/arch/arm/boot/dts/tegra30-beaver.dts
+++ b/arch/arm/boot/dts/tegra30-beaver.dts
@@ -1898,7 +1898,8 @@
 	spi@7000da00 {
 		status = "okay";
 		spi-max-frequency = <25000000>;
-		spi-flash@1 {
+
+		flash@1 {
 			compatible = "winbond,w25q32", "jedec,spi-nor";
 			reg = <1>;
 			spi-max-frequency = <20000000>;
@@ -1915,6 +1916,7 @@
 		nvidia,core-pwr-off-time = <0>;
 		nvidia,core-power-req-active-high;
 		nvidia,sys-clock-req-active-high;
+		core-supply = <&core_vdd_reg>;
 	};
 
 	ahub@70080000 {
@@ -1966,7 +1968,7 @@
 		status = "okay";
 	};
 
-	clk32k_in: clock@0 {
+	clk32k_in: clock-32k {
 		compatible = "fixed-clock";
 		clock-frequency = <32768>;
 		#clock-cells = <0>;
@@ -1985,7 +1987,7 @@
 		};
 	};
 
-	vdd_5v_in_reg: regulator@0 {
+	vdd_5v_in_reg: regulator-5v0 {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd_5v_in";
 		regulator-min-microvolt = <5000000>;
@@ -1993,7 +1995,7 @@
 		regulator-always-on;
 	};
 
-	chargepump_5v_reg: regulator@1 {
+	chargepump_5v_reg: regulator-chargepump {
 		compatible = "regulator-fixed";
 		regulator-name = "chargepump_5v";
 		regulator-min-microvolt = <5000000>;
@@ -2004,7 +2006,7 @@
 		gpio = <&pmic 0 GPIO_ACTIVE_HIGH>;
 	};
 
-	ddr_reg: regulator@2 {
+	ddr_reg: regulator-ddr {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd_ddr";
 		regulator-min-microvolt = <1500000>;
@@ -2016,7 +2018,7 @@
 		vin-supply = <&vdd_5v_in_reg>;
 	};
 
-	vdd_5v_sata_reg: regulator@3 {
+	vdd_5v_sata_reg: regulator-sata {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd_5v_sata";
 		regulator-min-microvolt = <5000000>;
@@ -2028,7 +2030,7 @@
 		vin-supply = <&vdd_5v_in_reg>;
 	};
 
-	usb1_vbus_reg: regulator@4 {
+	usb1_vbus_reg: regulator-usb1 {
 		compatible = "regulator-fixed";
 		regulator-name = "usb1_vbus";
 		regulator-min-microvolt = <5000000>;
@@ -2039,7 +2041,7 @@
 		vin-supply = <&vdd_5v_in_reg>;
 	};
 
-	usb3_vbus_reg: regulator@5 {
+	usb3_vbus_reg: regulator-usb3 {
 		compatible = "regulator-fixed";
 		regulator-name = "usb3_vbus";
 		regulator-min-microvolt = <5000000>;
@@ -2050,7 +2052,7 @@
 		vin-supply = <&vdd_5v_in_reg>;
 	};
 
-	sys_3v3_reg: regulator@6 {
+	sys_3v3_reg: regulator-3v3 {
 		compatible = "regulator-fixed";
 		regulator-name = "sys_3v3,vdd_3v3_alw";
 		regulator-min-microvolt = <3300000>;
@@ -2062,7 +2064,7 @@
 		vin-supply = <&vdd_5v_in_reg>;
 	};
 
-	sys_3v3_pexs_reg: regulator@7 {
+	sys_3v3_pexs_reg: regulator-pexs {
 		compatible = "regulator-fixed";
 		regulator-name = "sys_3v3_pexs";
 		regulator-min-microvolt = <3300000>;
@@ -2074,7 +2076,7 @@
 		vin-supply = <&sys_3v3_reg>;
 	};
 
-	vdd_5v0_hdmi: regulator@8 {
+	vdd_5v0_hdmi: regulator-hdmi {
 		compatible = "regulator-fixed";
 		regulator-name = "+VDD_5V_HDMI";
 		regulator-min-microvolt = <5000000>;
diff --git a/arch/arm/boot/dts/tegra30-cardhu-a02.dts b/arch/arm/boot/dts/tegra30-cardhu-a02.dts
index 4899e05a0d9c..247185314f46 100644
--- a/arch/arm/boot/dts/tegra30-cardhu-a02.dts
+++ b/arch/arm/boot/dts/tegra30-cardhu-a02.dts
@@ -16,7 +16,7 @@
 		keep-power-in-suspend;
 	};
 
-	ddr_reg: regulator@100 {
+	ddr_reg: regulator-ddr {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd_ddr";
 		regulator-min-microvolt = <1500000>;
@@ -27,7 +27,7 @@
 		gpio = <&pmic 6 GPIO_ACTIVE_HIGH>;
 	};
 
-	sys_3v3_reg: regulator@101 {
+	sys_3v3_reg: regulator-3v3 {
 		compatible = "regulator-fixed";
 		regulator-name = "sys_3v3";
 		regulator-min-microvolt = <3300000>;
@@ -38,7 +38,7 @@
 		gpio = <&pmic 7 GPIO_ACTIVE_HIGH>;
 	};
 
-	usb1_vbus_reg: regulator@102 {
+	usb1_vbus_reg: regulator-usb1 {
 		compatible = "regulator-fixed";
 		regulator-name = "usb1_vbus";
 		regulator-min-microvolt = <5000000>;
@@ -49,7 +49,7 @@
 		vin-supply = <&vdd_5v0_reg>;
 	};
 
-	usb3_vbus_reg: regulator@103 {
+	usb3_vbus_reg: regulator-usb3 {
 		compatible = "regulator-fixed";
 		regulator-name = "usb3_vbus";
 		regulator-min-microvolt = <5000000>;
@@ -60,7 +60,7 @@
 		vin-supply = <&vdd_5v0_reg>;
 	};
 
-	vdd_5v0_reg: regulator@104 {
+	vdd_5v0_reg: regulator-5v0 {
 		compatible = "regulator-fixed";
 		regulator-name = "5v0";
 		regulator-min-microvolt = <5000000>;
@@ -69,7 +69,7 @@
 		gpio = <&pmic 2 GPIO_ACTIVE_HIGH>;
 	};
 
-	vdd_bl_reg: regulator@105 {
+	vdd_bl_reg: regulator-bl {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd_bl";
 		regulator-min-microvolt = <5000000>;
diff --git a/arch/arm/boot/dts/tegra30-cardhu-a04.dts b/arch/arm/boot/dts/tegra30-cardhu-a04.dts
index a11028b8b67b..2911f08863a0 100644
--- a/arch/arm/boot/dts/tegra30-cardhu-a04.dts
+++ b/arch/arm/boot/dts/tegra30-cardhu-a04.dts
@@ -16,7 +16,7 @@
 		keep-power-in-suspend;
 	};
 
-	ddr_reg: regulator@100 {
+	ddr_reg: regulator-ddr {
 		compatible = "regulator-fixed";
 		regulator-name = "ddr";
 		regulator-min-microvolt = <1500000>;
@@ -27,7 +27,7 @@
 		gpio = <&pmic 7 GPIO_ACTIVE_HIGH>;
 	};
 
-	sys_3v3_reg: regulator@101 {
+	sys_3v3_reg: regulator-3v3 {
 		compatible = "regulator-fixed";
 		regulator-name = "sys_3v3";
 		regulator-min-microvolt = <3300000>;
@@ -38,7 +38,7 @@
 		gpio = <&pmic 6 GPIO_ACTIVE_HIGH>;
 	};
 
-	usb1_vbus_reg: regulator@102 {
+	usb1_vbus_reg: regulator-usb1 {
 		compatible = "regulator-fixed";
 		regulator-name = "usb1_vbus";
 		regulator-min-microvolt = <5000000>;
@@ -49,7 +49,7 @@
 		vin-supply = <&vdd_5v0_reg>;
 	};
 
-	usb3_vbus_reg: regulator@103 {
+	usb3_vbus_reg: regulator-usb3 {
 		compatible = "regulator-fixed";
 		regulator-name = "usb3_vbus";
 		regulator-min-microvolt = <5000000>;
@@ -60,7 +60,7 @@
 		vin-supply = <&vdd_5v0_reg>;
 	};
 
-	vdd_5v0_reg: regulator@104 {
+	vdd_5v0_reg: regulator-5v0 {
 		compatible = "regulator-fixed";
 		regulator-name = "5v0";
 		regulator-min-microvolt = <5000000>;
@@ -69,7 +69,7 @@
 		gpio = <&pmic 8 GPIO_ACTIVE_HIGH>;
 	};
 
-	vdd_bl_reg: regulator@105 {
+	vdd_bl_reg: regulator-bl {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd_bl";
 		regulator-min-microvolt = <5000000>;
@@ -80,7 +80,7 @@
 		gpio = <&gpio TEGRA_GPIO(DD, 2) GPIO_ACTIVE_HIGH>;
 	};
 
-	vdd_bl2_reg: regulator@106 {
+	vdd_bl2_reg: regulator-bl2 {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd_bl2";
 		regulator-min-microvolt = <5000000>;
diff --git a/arch/arm/boot/dts/tegra30-cardhu.dtsi b/arch/arm/boot/dts/tegra30-cardhu.dtsi
index 448f1397e64a..540530c983ff 100644
--- a/arch/arm/boot/dts/tegra30-cardhu.dtsi
+++ b/arch/arm/boot/dts/tegra30-cardhu.dtsi
@@ -175,6 +175,7 @@
 
 	serial@70006200 {
 		compatible = "nvidia,tegra30-hsuart";
+		/delete-property/ reg-shift;
 		status = "okay";
 	};
 
@@ -209,7 +210,7 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <0x70>;
-			reset-gpio = <&gpio TEGRA_GPIO(BB, 0) GPIO_ACTIVE_LOW>;
+			reset-gpios = <&gpio TEGRA_GPIO(BB, 0) GPIO_ACTIVE_LOW>;
 		};
 	};
 
@@ -374,7 +375,8 @@
 	spi@7000da00 {
 		status = "okay";
 		spi-max-frequency = <25000000>;
-		spi-flash@1 {
+
+		flash@1 {
 			compatible = "winbond,w25q32", "jedec,spi-nor";
 			reg = <1>;
 			spi-max-frequency = <20000000>;
@@ -391,6 +393,7 @@
 		nvidia,core-pwr-off-time = <0>;
 		nvidia,core-power-req-active-high;
 		nvidia,sys-clock-req-active-high;
+		core-supply = <&vdd_core>;
 	};
 
 	ahub@70080000 {
@@ -433,7 +436,7 @@
 		default-brightness-level = <6>;
 	};
 
-	clk32k_in: clock@0 {
+	clk32k_in: clock-32k {
 		compatible = "fixed-clock";
 		clock-frequency = <32768>;
 		#clock-cells = <0>;
@@ -475,7 +478,7 @@
 		backlight = <&backlight>;
 	};
 
-	vdd_ac_bat_reg: regulator@0 {
+	vdd_ac_bat_reg: regulator-acbat {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd_ac_bat";
 		regulator-min-microvolt = <5000000>;
@@ -483,7 +486,7 @@
 		regulator-always-on;
 	};
 
-	cam_1v8_reg: regulator@1 {
+	cam_1v8_reg: regulator-cam {
 		compatible = "regulator-fixed";
 		regulator-name = "cam_1v8";
 		regulator-min-microvolt = <1800000>;
@@ -493,7 +496,7 @@
 		vin-supply = <&vio_reg>;
 	};
 
-	cp_5v_reg: regulator@2 {
+	cp_5v_reg: regulator-5v0cp {
 		compatible = "regulator-fixed";
 		regulator-name = "cp_5v";
 		regulator-min-microvolt = <5000000>;
@@ -504,7 +507,7 @@
 		gpio = <&pmic 0 GPIO_ACTIVE_HIGH>;
 	};
 
-	emmc_3v3_reg: regulator@3 {
+	emmc_3v3_reg: regulator-emmc {
 		compatible = "regulator-fixed";
 		regulator-name = "emmc_3v3";
 		regulator-min-microvolt = <3300000>;
@@ -516,7 +519,7 @@
 		vin-supply = <&sys_3v3_reg>;
 	};
 
-	modem_3v3_reg: regulator@4 {
+	modem_3v3_reg: regulator-modem {
 		compatible = "regulator-fixed";
 		regulator-name = "modem_3v3";
 		regulator-min-microvolt = <3300000>;
@@ -525,7 +528,7 @@
 		gpio = <&gpio TEGRA_GPIO(D, 6) GPIO_ACTIVE_HIGH>;
 	};
 
-	pex_hvdd_3v3_reg: regulator@5 {
+	pex_hvdd_3v3_reg: regulator-pex {
 		compatible = "regulator-fixed";
 		regulator-name = "pex_hvdd_3v3";
 		regulator-min-microvolt = <3300000>;
@@ -535,7 +538,7 @@
 		vin-supply = <&sys_3v3_reg>;
 	};
 
-	vdd_cam1_ldo_reg: regulator@6 {
+	vdd_cam1_ldo_reg: regulator-cam1 {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd_cam1_ldo";
 		regulator-min-microvolt = <2800000>;
@@ -545,7 +548,7 @@
 		vin-supply = <&sys_3v3_reg>;
 	};
 
-	vdd_cam2_ldo_reg: regulator@7 {
+	vdd_cam2_ldo_reg: regulator-cam2 {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd_cam2_ldo";
 		regulator-min-microvolt = <2800000>;
@@ -555,7 +558,7 @@
 		vin-supply = <&sys_3v3_reg>;
 	};
 
-	vdd_cam3_ldo_reg: regulator@8 {
+	vdd_cam3_ldo_reg: regulator-cam3 {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd_cam3_ldo";
 		regulator-min-microvolt = <3300000>;
@@ -565,7 +568,7 @@
 		vin-supply = <&sys_3v3_reg>;
 	};
 
-	vdd_com_reg: regulator@9 {
+	vdd_com_reg: regulator-com {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd_com";
 		regulator-min-microvolt = <3300000>;
@@ -577,7 +580,7 @@
 		vin-supply = <&sys_3v3_reg>;
 	};
 
-	vdd_fuse_3v3_reg: regulator@10 {
+	vdd_fuse_3v3_reg: regulator-fuse {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd_fuse_3v3";
 		regulator-min-microvolt = <3300000>;
@@ -587,7 +590,7 @@
 		vin-supply = <&sys_3v3_reg>;
 	};
 
-	vdd_pnl1_reg: regulator@11 {
+	vdd_pnl1_reg: regulator-pnl1 {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd_pnl1";
 		regulator-min-microvolt = <3300000>;
@@ -599,7 +602,7 @@
 		vin-supply = <&sys_3v3_reg>;
 	};
 
-	vdd_vid_reg: regulator@12 {
+	vdd_vid_reg: regulator-vid {
 		compatible = "regulator-fixed";
 		regulator-name = "vddio_vid";
 		regulator-min-microvolt = <5000000>;
@@ -682,7 +685,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		power {
+		key-power {
 			label = "Power";
 			interrupt-parent = <&pmic>;
 			interrupts = <2 0>;
@@ -691,14 +694,14 @@
 			wakeup-source;
 		};
 
-		volume-down {
+		key-volume-down {
 			label = "Volume Down";
 			gpios = <&gpio TEGRA_GPIO(R, 0) GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_VOLUMEDOWN>;
 			debounce-interval = <10>;
 		};
 
-		volume-up {
+		key-volume-up {
 			label = "Volume Up";
 			gpios = <&gpio TEGRA_GPIO(R, 1) GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_VOLUMEUP>;
diff --git a/arch/arm/boot/dts/tegra30-colibri-eval-v3.dts b/arch/arm/boot/dts/tegra30-colibri-eval-v3.dts
index 7d4a6ca4936a..8dbc15f9a9e4 100644
--- a/arch/arm/boot/dts/tegra30-colibri-eval-v3.dts
+++ b/arch/arm/boot/dts/tegra30-colibri-eval-v3.dts
@@ -145,7 +145,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		wakeup {
+		key-wakeup {
 			label = "SODIMM pin 45 wakeup";
 			gpios = <&gpio TEGRA_GPIO(V, 1) GPIO_ACTIVE_HIGH>;
 			linux,code = <KEY_WAKEUP>;
diff --git a/arch/arm/boot/dts/tegra30-colibri.dtsi b/arch/arm/boot/dts/tegra30-colibri.dtsi
index 413e35215804..2867a138e011 100644
--- a/arch/arm/boot/dts/tegra30-colibri.dtsi
+++ b/arch/arm/boot/dts/tegra30-colibri.dtsi
@@ -239,7 +239,7 @@
 				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
 			};
 			spdif-in-pk6 {
-				nvidia,pins =	"spdif_in_pk6";
+				nvidia,pins = "spdif_in_pk6";
 				nvidia,function = "hda";
 				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
 				nvidia,tristate = <TEGRA_PIN_DISABLE>;
@@ -364,7 +364,7 @@
 			};
 			/* Multiplexed and therefore disabled */
 			cam-mclk-pcc0 {
-				nvidia,pins =	"cam_mclk_pcc0";
+				nvidia,pins = "cam_mclk_pcc0";
 				nvidia,function = "vi_alt3";
 				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
 				nvidia,tristate = <TEGRA_PIN_ENABLE>;
@@ -511,7 +511,7 @@
 
 			/* Colibri USBC_DET */
 			spdif-out-pk5 {
-				nvidia,pins =	"spdif_out_pk5";
+				nvidia,pins = "spdif_out_pk5";
 				nvidia,function = "rsvd2";
 				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
 				nvidia,tristate = <TEGRA_PIN_DISABLE>;
@@ -701,10 +701,12 @@
 
 	serial@70006040 {
 		compatible = "nvidia,tegra30-hsuart";
+		/delete-property/ reg-shift;
 	};
 
 	serial@70006300 {
 		compatible = "nvidia,tegra30-hsuart";
+		/delete-property/ reg-shift;
 	};
 
 	hdmi_ddc: i2c@7000c700 {
@@ -765,9 +767,14 @@
 
 				vddctrl_reg: vddctrl {
 					regulator-name = "+V1.0_VDD_CPU";
-					regulator-min-microvolt = <1150000>;
-					regulator-max-microvolt = <1150000>;
+					regulator-min-microvolt = <800000>;
+					regulator-max-microvolt = <1250000>;
+					regulator-coupled-with = <&vdd_core>;
+					regulator-coupled-max-spread = <300000>;
+					regulator-max-step-microvolt = <100000>;
 					regulator-always-on;
+
+					nvidia,tegra-cpu-regulator;
 				};
 
 				reg_1v8_vio: vio {
@@ -842,7 +849,7 @@
 		touchscreen@41 {
 			compatible = "st,stmpe811";
 			reg = <0x41>;
-			irq-gpio = <&gpio TEGRA_GPIO(V, 0) IRQ_TYPE_LEVEL_LOW>;
+			irq-gpio = <&gpio TEGRA_GPIO(V, 0) GPIO_ACTIVE_LOW>;
 			interrupt-controller;
 			id = <0>;
 			blocks = <0x5>;
@@ -890,18 +897,20 @@
 		};
 
 		/* SW: +V1.2_VDD_CORE */
-		regulator@60 {
+		vdd_core: regulator@60 {
 			compatible = "ti,tps62362";
 			reg = <0x60>;
 
 			regulator-name = "tps62362-vout";
 			regulator-min-microvolt = <900000>;
 			regulator-max-microvolt = <1400000>;
+			regulator-coupled-with = <&vddctrl_reg>;
+			regulator-coupled-max-spread = <300000>;
+			regulator-max-step-microvolt = <100000>;
 			regulator-boot-on;
 			regulator-always-on;
-			ti,vsel0-state-low;
-			/* VSEL1: EN_CORE_DVFS_N low for DVFS */
-			ti,vsel1-state-low;
+
+			nvidia,tegra-core-regulator;
 		};
 	};
 
@@ -914,6 +923,7 @@
 		nvidia,core-pwr-off-time = <0>;
 		nvidia,core-power-req-active-high;
 		nvidia,sys-clock-req-active-high;
+		core-supply = <&vdd_core>;
 
 		/* Set DEV_OFF bit in DCDC control register of TPS65911 PMIC */
 		i2c-thermtrip {
@@ -950,7 +960,8 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		asix@1 {
+		ethernet@1 {
+			compatible = "usbb95,772b";
 			reg = <1>;
 			local-mac-address = [00 00 00 00 00 00];
 		};
@@ -1044,7 +1055,7 @@
 };
 
 &gpio {
-	lan-reset-n {
+	lan-reset-n-hog {
 		gpio-hog;
 		gpios = <TEGRA_GPIO(DD, 0) GPIO_ACTIVE_HIGH>;
 		output-high;
diff --git a/arch/arm/boot/dts/tegra30-cpu-opp-microvolt.dtsi b/arch/arm/boot/dts/tegra30-cpu-opp-microvolt.dtsi
index 1be715d2a442..b8e0e9117021 100644
--- a/arch/arm/boot/dts/tegra30-cpu-opp-microvolt.dtsi
+++ b/arch/arm/boot/dts/tegra30-cpu-opp-microvolt.dtsi
@@ -1,288 +1,288 @@
 // SPDX-License-Identifier: GPL-2.0
 
 / {
-	cpu0_opp_table: cpu_opp_table0 {
-		opp@51000000,800 {
+	cpu0_opp_table: opp-table-cpu0 {
+		opp-51000000-800 {
 			opp-microvolt = <800000 800000 1250000>;
 		};
 
-		opp@51000000,850 {
+		opp-51000000-850 {
 			opp-microvolt = <850000 850000 1250000>;
 		};
 
-		opp@51000000,912 {
+		opp-51000000-912 {
 			opp-microvolt = <912000 912000 1250000>;
 		};
 
-		opp@102000000,800 {
+		opp-102000000-800 {
 			opp-microvolt = <800000 800000 1250000>;
 		};
 
-		opp@102000000,850 {
+		opp-102000000-850 {
 			opp-microvolt = <850000 850000 1250000>;
 		};
 
-		opp@102000000,912 {
+		opp-102000000-912 {
 			opp-microvolt = <912000 912000 1250000>;
 		};
 
-		opp@204000000,800 {
+		opp-204000000-800 {
 			opp-microvolt = <800000 800000 1250000>;
 		};
 
-		opp@204000000,850 {
+		opp-204000000-850 {
 			opp-microvolt = <850000 850000 1250000>;
 		};
 
-		opp@204000000,912 {
+		opp-204000000-912 {
 			opp-microvolt = <912000 912000 1250000>;
 		};
 
-		opp@312000000,850 {
+		opp-312000000-850 {
 			opp-microvolt = <850000 850000 1250000>;
 		};
 
-		opp@312000000,912 {
+		opp-312000000-912 {
 			opp-microvolt = <912000 912000 1250000>;
 		};
 
-		opp@340000000,800 {
+		opp-340000000-800 {
 			opp-microvolt = <800000 800000 1250000>;
 		};
 
-		opp@340000000,850 {
+		opp-340000000-850 {
 			opp-microvolt = <850000 850000 1250000>;
 		};
 
-		opp@370000000,800 {
+		opp-370000000-800 {
 			opp-microvolt = <800000 800000 1250000>;
 		};
 
-		opp@456000000,850 {
+		opp-456000000-850 {
 			opp-microvolt = <850000 850000 1250000>;
 		};
 
-		opp@456000000,912 {
+		opp-456000000-912 {
 			opp-microvolt = <912000 912000 1250000>;
 		};
 
-		opp@475000000,800 {
+		opp-475000000-800 {
 			opp-microvolt = <800000 800000 1250000>;
 		};
 
-		opp@475000000,850 {
+		opp-475000000-850 {
 			opp-microvolt = <850000 850000 1250000>;
 		};
 
-		opp@608000000,850 {
+		opp-608000000-850 {
 			opp-microvolt = <850000 850000 1250000>;
 		};
 
-		opp@608000000,912 {
+		opp-608000000-912 {
 			opp-microvolt = <912000 912000 1250000>;
 		};
 
-		opp@620000000,850 {
+		opp-620000000-850 {
 			opp-microvolt = <850000 850000 1250000>;
 		};
 
-		opp@640000000,850 {
+		opp-640000000-850 {
 			opp-microvolt = <850000 850000 1250000>;
 		};
 
-		opp@640000000,900 {
+		opp-640000000-900 {
 			opp-microvolt = <900000 900000 1250000>;
 		};
 
-		opp@760000000,850 {
+		opp-760000000-850 {
 			opp-microvolt = <850000 850000 1250000>;
 		};
 
-		opp@760000000,900 {
+		opp-760000000-900 {
 			opp-microvolt = <900000 900000 1250000>;
 		};
 
-		opp@760000000,912 {
+		opp-760000000-912 {
 			opp-microvolt = <912000 912000 1250000>;
 		};
 
-		opp@760000000,975 {
+		opp-760000000-975 {
 			opp-microvolt = <975000 975000 1250000>;
 		};
 
-		opp@816000000,850 {
+		opp-816000000-850 {
 			opp-microvolt = <850000 850000 1250000>;
 		};
 
-		opp@816000000,912 {
+		opp-816000000-912 {
 			opp-microvolt = <912000 912000 1250000>;
 		};
 
-		opp@860000000,850 {
+		opp-860000000-850 {
 			opp-microvolt = <850000 850000 1250000>;
 		};
 
-		opp@860000000,900 {
+		opp-860000000-900 {
 			opp-microvolt = <900000 900000 1250000>;
 		};
 
-		opp@860000000,975 {
+		opp-860000000-975 {
 			opp-microvolt = <975000 975000 1250000>;
 		};
 
-		opp@860000000,1000 {
+		opp-860000000-1000 {
 			opp-microvolt = <1000000 1000000 1250000>;
 		};
 
-		opp@910000000,900 {
+		opp-910000000-900 {
 			opp-microvolt = <900000 900000 1250000>;
 		};
 
-		opp@1000000000,900 {
+		opp-1000000000-900 {
 			opp-microvolt = <900000 900000 1250000>;
 		};
 
-		opp@1000000000,975 {
+		opp-1000000000-975 {
 			opp-microvolt = <975000 975000 1250000>;
 		};
 
-		opp@1000000000,1000 {
+		opp-1000000000-1000 {
 			opp-microvolt = <1000000 1000000 1250000>;
 		};
 
-		opp@1000000000,1025 {
+		opp-1000000000-1025 {
 			opp-microvolt = <1025000 1025000 1250000>;
 		};
 
-		opp@1100000000,900 {
+		opp-1100000000-900 {
 			opp-microvolt = <900000 900000 1250000>;
 		};
 
-		opp@1100000000,975 {
+		opp-1100000000-975 {
 			opp-microvolt = <975000 975000 1250000>;
 		};
 
-		opp@1100000000,1000 {
+		opp-1100000000-1000 {
 			opp-microvolt = <1000000 1000000 1250000>;
 		};
 
-		opp@1100000000,1025 {
+		opp-1100000000-1025 {
 			opp-microvolt = <1025000 1025000 1250000>;
 		};
 
-		opp@1100000000,1075 {
+		opp-1100000000-1075 {
 			opp-microvolt = <1075000 1075000 1250000>;
 		};
 
-		opp@1150000000,975 {
+		opp-1150000000-975 {
 			opp-microvolt = <975000 975000 1250000>;
 		};
 
-		opp@1200000000,975 {
+		opp-1200000000-975 {
 			opp-microvolt = <975000 975000 1250000>;
 		};
 
-		opp@1200000000,1000 {
+		opp-1200000000-1000 {
 			opp-microvolt = <1000000 1000000 1250000>;
 		};
 
-		opp@1200000000,1025 {
+		opp-1200000000-1025 {
 			opp-microvolt = <1025000 1025000 1250000>;
 		};
 
-		opp@1200000000,1050 {
+		opp-1200000000-1050 {
 			opp-microvolt = <1050000 1050000 1250000>;
 		};
 
-		opp@1200000000,1075 {
+		opp-1200000000-1075 {
 			opp-microvolt = <1075000 1075000 1250000>;
 		};
 
-		opp@1200000000,1100 {
+		opp-1200000000-1100 {
 			opp-microvolt = <1100000 1100000 1250000>;
 		};
 
-		opp@1300000000,1000 {
+		opp-1300000000-1000 {
 			opp-microvolt = <1000000 1000000 1250000>;
 		};
 
-		opp@1300000000,1025 {
+		opp-1300000000-1025 {
 			opp-microvolt = <1025000 1025000 1250000>;
 		};
 
-		opp@1300000000,1050 {
+		opp-1300000000-1050 {
 			opp-microvolt = <1050000 1050000 1250000>;
 		};
 
-		opp@1300000000,1075 {
+		opp-1300000000-1075 {
 			opp-microvolt = <1075000 1075000 1250000>;
 		};
 
-		opp@1300000000,1100 {
+		opp-1300000000-1100 {
 			opp-microvolt = <1100000 1100000 1250000>;
 		};
 
-		opp@1300000000,1125 {
+		opp-1300000000-1125 {
 			opp-microvolt = <1125000 1125000 1250000>;
 		};
 
-		opp@1300000000,1150 {
+		opp-1300000000-1150 {
 			opp-microvolt = <1150000 1150000 1250000>;
 		};
 
-		opp@1300000000,1175 {
+		opp-1300000000-1175 {
 			opp-microvolt = <1175000 1175000 1250000>;
 		};
 
-		opp@1400000000,1100 {
+		opp-1400000000-1100 {
 			opp-microvolt = <1100000 1100000 1250000>;
 		};
 
-		opp@1400000000,1125 {
+		opp-1400000000-1125 {
 			opp-microvolt = <1125000 1125000 1250000>;
 		};
 
-		opp@1400000000,1150 {
+		opp-1400000000-1150 {
 			opp-microvolt = <1150000 1150000 1250000>;
 		};
 
-		opp@1400000000,1175 {
+		opp-1400000000-1175 {
 			opp-microvolt = <1175000 1175000 1250000>;
 		};
 
-		opp@1400000000,1237 {
+		opp-1400000000-1237 {
 			opp-microvolt = <1237000 1237000 1250000>;
 		};
 
-		opp@1500000000,1125 {
+		opp-1500000000-1125 {
 			opp-microvolt = <1125000 1125000 1250000>;
 		};
 
-		opp@1500000000,1150 {
+		opp-1500000000-1150 {
 			opp-microvolt = <1150000 1150000 1250000>;
 		};
 
-		opp@1500000000,1200 {
+		opp-1500000000-1200 {
 			opp-microvolt = <1200000 1200000 1250000>;
 		};
 
-		opp@1500000000,1237 {
+		opp-1500000000-1237 {
 			opp-microvolt = <1237000 1237000 1250000>;
 		};
 
-		opp@1600000000,1212 {
+		opp-1600000000-1212 {
 			opp-microvolt = <1212000 1212000 1250000>;
 		};
 
-		opp@1600000000,1237 {
+		opp-1600000000-1237 {
 			opp-microvolt = <1237000 1237000 1250000>;
 		};
 
-		opp@1700000000,1212 {
+		opp-1700000000-1212 {
 			opp-microvolt = <1212000 1212000 1250000>;
 		};
 
-		opp@1700000000,1237 {
+		opp-1700000000-1237 {
 			opp-microvolt = <1237000 1237000 1250000>;
 		};
 	};
diff --git a/arch/arm/boot/dts/tegra30-cpu-opp.dtsi b/arch/arm/boot/dts/tegra30-cpu-opp.dtsi
index 72f2fe26cc0e..5b9ebb75a09f 100644
--- a/arch/arm/boot/dts/tegra30-cpu-opp.dtsi
+++ b/arch/arm/boot/dts/tegra30-cpu-opp.dtsi
@@ -1,116 +1,116 @@
 // SPDX-License-Identifier: GPL-2.0
 
 / {
-	cpu0_opp_table: cpu_opp_table0 {
+	cpu0_opp_table: opp-table-cpu0 {
 		compatible = "operating-points-v2";
 		opp-shared;
 
-		opp@51000000,800 {
+		opp-51000000-800 {
 			clock-latency-ns = <100000>;
 			opp-supported-hw = <0x1F 0x31FE>;
 			opp-hz = /bits/ 64 <51000000>;
 		};
 
-		opp@51000000,850 {
+		opp-51000000-850 {
 			clock-latency-ns = <100000>;
 			opp-supported-hw = <0x1F 0x0C01>;
 			opp-hz = /bits/ 64 <51000000>;
 		};
 
-		opp@51000000,912 {
+		opp-51000000-912 {
 			clock-latency-ns = <100000>;
 			opp-supported-hw = <0x1F 0x0200>;
 			opp-hz = /bits/ 64 <51000000>;
 		};
 
-		opp@102000000,800 {
+		opp-102000000-800 {
 			clock-latency-ns = <100000>;
 			opp-supported-hw = <0x1F 0x31FE>;
 			opp-hz = /bits/ 64 <102000000>;
 		};
 
-		opp@102000000,850 {
+		opp-102000000-850 {
 			clock-latency-ns = <100000>;
 			opp-supported-hw = <0x1F 0x0C01>;
 			opp-hz = /bits/ 64 <102000000>;
 		};
 
-		opp@102000000,912 {
+		opp-102000000-912 {
 			clock-latency-ns = <100000>;
 			opp-supported-hw = <0x1F 0x0200>;
 			opp-hz = /bits/ 64 <102000000>;
 		};
 
-		opp@204000000,800 {
+		opp-204000000-800 {
 			clock-latency-ns = <100000>;
 			opp-supported-hw = <0x1F 0x31FE>;
 			opp-hz = /bits/ 64 <204000000>;
 			opp-suspend;
 		};
 
-		opp@204000000,850 {
+		opp-204000000-850 {
 			clock-latency-ns = <100000>;
 			opp-supported-hw = <0x1F 0x0C01>;
 			opp-hz = /bits/ 64 <204000000>;
 			opp-suspend;
 		};
 
-		opp@204000000,912 {
+		opp-204000000-912 {
 			clock-latency-ns = <100000>;
 			opp-supported-hw = <0x1F 0x0200>;
 			opp-hz = /bits/ 64 <204000000>;
 			opp-suspend;
 		};
 
-		opp@312000000,850 {
+		opp-312000000-850 {
 			clock-latency-ns = <100000>;
 			opp-supported-hw = <0x1F 0x0C00>;
 			opp-hz = /bits/ 64 <312000000>;
 		};
 
-		opp@312000000,912 {
+		opp-312000000-912 {
 			clock-latency-ns = <100000>;
 			opp-supported-hw = <0x1F 0x0200>;
 			opp-hz = /bits/ 64 <312000000>;
 		};
 
-		opp@340000000,800 {
+		opp-340000000-800 {
 			clock-latency-ns = <100000>;
 			opp-supported-hw = <0x1F 0x0192>;
 			opp-hz = /bits/ 64 <340000000>;
 		};
 
-		opp@340000000,850 {
+		opp-340000000-850 {
 			clock-latency-ns = <100000>;
 			opp-supported-hw = <0x0F 0x0001>;
 			opp-hz = /bits/ 64 <340000000>;
 		};
 
-		opp@370000000,800 {
+		opp-370000000-800 {
 			clock-latency-ns = <100000>;
 			opp-supported-hw = <0x1E 0x306C>;
 			opp-hz = /bits/ 64 <370000000>;
 		};
 
-		opp@456000000,850 {
+		opp-456000000-850 {
 			clock-latency-ns = <100000>;
 			opp-supported-hw = <0x1F 0x0C00>;
 			opp-hz = /bits/ 64 <456000000>;
 		};
 
-		opp@456000000,912 {
+		opp-456000000-912 {
 			clock-latency-ns = <100000>;
 			opp-supported-hw = <0x1F 0x0200>;
 			opp-hz = /bits/ 64 <456000000>;
 		};
 
-		opp@475000000,800 {
+		opp-475000000-800 {
 			clock-latency-ns = <100000>;
 			opp-supported-hw = <0x1E 0x31FE>;
 			opp-hz = /bits/ 64 <475000000>;
 		};
 
-		opp@475000000,850 {
+		opp-475000000-850 {
 			clock-latency-ns = <100000>;
 			opp-supported-hw = <0x0F 0x0001>, <0x01 0x0002>,
 					   <0x01 0x0010>, <0x01 0x0080>,
@@ -118,25 +118,25 @@
 			opp-hz = /bits/ 64 <475000000>;
 		};
 
-		opp@608000000,850 {
+		opp-608000000-850 {
 			clock-latency-ns = <100000>;
 			opp-supported-hw = <0x1F 0x0400>;
 			opp-hz = /bits/ 64 <608000000>;
 		};
 
-		opp@608000000,912 {
+		opp-608000000-912 {
 			clock-latency-ns = <100000>;
 			opp-supported-hw = <0x1F 0x0200>;
 			opp-hz = /bits/ 64 <608000000>;
 		};
 
-		opp@620000000,850 {
+		opp-620000000-850 {
 			clock-latency-ns = <100000>;
 			opp-supported-hw = <0x1E 0x306C>;
 			opp-hz = /bits/ 64 <620000000>;
 		};
 
-		opp@640000000,850 {
+		opp-640000000-850 {
 			clock-latency-ns = <100000>;
 			opp-supported-hw = <0x0F 0x0001>, <0x02 0x0002>,
 					   <0x04 0x0002>, <0x08 0x0002>,
@@ -149,13 +149,13 @@
 			opp-hz = /bits/ 64 <640000000>;
 		};
 
-		opp@640000000,900 {
+		opp-640000000-900 {
 			clock-latency-ns = <100000>;
 			opp-supported-hw = <0x01 0x0192>;
 			opp-hz = /bits/ 64 <640000000>;
 		};
 
-		opp@760000000,850 {
+		opp-760000000-850 {
 			clock-latency-ns = <100000>;
 			opp-supported-hw = <0x1E 0x3461>, <0x08 0x0002>,
 					   <0x08 0x0004>, <0x08 0x0008>,
@@ -165,7 +165,7 @@
 			opp-hz = /bits/ 64 <760000000>;
 		};
 
-		opp@760000000,900 {
+		opp-760000000-900 {
 			clock-latency-ns = <100000>;
 			opp-supported-hw = <0x01 0x0001>, <0x02 0x0002>,
 					   <0x04 0x0002>, <0x02 0x0004>,
@@ -177,37 +177,37 @@
 			opp-hz = /bits/ 64 <760000000>;
 		};
 
-		opp@760000000,912 {
+		opp-760000000-912 {
 			clock-latency-ns = <100000>;
 			opp-supported-hw = <0x1F 0x0200>;
 			opp-hz = /bits/ 64 <760000000>;
 		};
 
-		opp@760000000,975 {
+		opp-760000000-975 {
 			clock-latency-ns = <100000>;
 			opp-supported-hw = <0x01 0x0192>;
 			opp-hz = /bits/ 64 <760000000>;
 		};
 
-		opp@816000000,850 {
+		opp-816000000-850 {
 			clock-latency-ns = <100000>;
 			opp-supported-hw = <0x1F 0x0400>;
 			opp-hz = /bits/ 64 <816000000>;
 		};
 
-		opp@816000000,912 {
+		opp-816000000-912 {
 			clock-latency-ns = <100000>;
 			opp-supported-hw = <0x1F 0x0200>;
 			opp-hz = /bits/ 64 <816000000>;
 		};
 
-		opp@860000000,850 {
+		opp-860000000-850 {
 			clock-latency-ns = <100000>;
 			opp-supported-hw = <0x0C 0x0001>;
 			opp-hz = /bits/ 64 <860000000>;
 		};
 
-		opp@860000000,900 {
+		opp-860000000-900 {
 			clock-latency-ns = <100000>;
 			opp-supported-hw = <0x02 0x0001>, <0x04 0x0002>,
 					   <0x08 0x0002>, <0x04 0x0004>,
@@ -220,7 +220,7 @@
 			opp-hz = /bits/ 64 <860000000>;
 		};
 
-		opp@860000000,975 {
+		opp-860000000-975 {
 			clock-latency-ns = <100000>;
 			opp-supported-hw = <0x01 0x0001>, <0x02 0x0002>,
 					   <0x02 0x0004>, <0x02 0x0008>,
@@ -229,25 +229,25 @@
 			opp-hz = /bits/ 64 <860000000>;
 		};
 
-		opp@860000000,1000 {
+		opp-860000000-1000 {
 			clock-latency-ns = <100000>;
 			opp-supported-hw = <0x01 0x0192>;
 			opp-hz = /bits/ 64 <860000000>;
 		};
 
-		opp@910000000,900 {
+		opp-910000000-900 {
 			clock-latency-ns = <100000>;
 			opp-supported-hw = <0x18 0x3060>;
 			opp-hz = /bits/ 64 <910000000>;
 		};
 
-		opp@1000000000,900 {
+		opp-1000000000-900 {
 			clock-latency-ns = <100000>;
 			opp-supported-hw = <0x0C 0x0001>;
 			opp-hz = /bits/ 64 <1000000000>;
 		};
 
-		opp@1000000000,975 {
+		opp-1000000000-975 {
 			clock-latency-ns = <100000>;
 			opp-supported-hw = <0x03 0x0001>, <0x04 0x0002>,
 					   <0x08 0x0002>, <0x04 0x0004>,
@@ -260,25 +260,25 @@
 			opp-hz = /bits/ 64 <1000000000>;
 		};
 
-		opp@1000000000,1000 {
+		opp-1000000000-1000 {
 			clock-latency-ns = <100000>;
 			opp-supported-hw = <0x02 0x019E>;
 			opp-hz = /bits/ 64 <1000000000>;
 		};
 
-		opp@1000000000,1025 {
+		opp-1000000000-1025 {
 			clock-latency-ns = <100000>;
 			opp-supported-hw = <0x01 0x0192>;
 			opp-hz = /bits/ 64 <1000000000>;
 		};
 
-		opp@1100000000,900 {
+		opp-1100000000-900 {
 			clock-latency-ns = <100000>;
 			opp-supported-hw = <0x08 0x0001>;
 			opp-hz = /bits/ 64 <1100000000>;
 		};
 
-		opp@1100000000,975 {
+		opp-1100000000-975 {
 			clock-latency-ns = <100000>;
 			opp-supported-hw = <0x06 0x0001>, <0x08 0x0002>,
 					   <0x08 0x0004>, <0x08 0x0008>,
@@ -288,7 +288,7 @@
 			opp-hz = /bits/ 64 <1100000000>;
 		};
 
-		opp@1100000000,1000 {
+		opp-1100000000-1000 {
 			clock-latency-ns = <100000>;
 			opp-supported-hw = <0x01 0x0001>, <0x04 0x0002>,
 					   <0x04 0x0004>, <0x04 0x0008>,
@@ -297,31 +297,31 @@
 			opp-hz = /bits/ 64 <1100000000>;
 		};
 
-		opp@1100000000,1025 {
+		opp-1100000000-1025 {
 			clock-latency-ns = <100000>;
 			opp-supported-hw = <0x02 0x019E>;
 			opp-hz = /bits/ 64 <1100000000>;
 		};
 
-		opp@1100000000,1075 {
+		opp-1100000000-1075 {
 			clock-latency-ns = <100000>;
 			opp-supported-hw = <0x01 0x0192>;
 			opp-hz = /bits/ 64 <1100000000>;
 		};
 
-		opp@1150000000,975 {
+		opp-1150000000-975 {
 			clock-latency-ns = <100000>;
 			opp-supported-hw = <0x18 0x3060>;
 			opp-hz = /bits/ 64 <1150000000>;
 		};
 
-		opp@1200000000,975 {
+		opp-1200000000-975 {
 			clock-latency-ns = <100000>;
 			opp-supported-hw = <0x08 0x0001>;
 			opp-hz = /bits/ 64 <1200000000>;
 		};
 
-		opp@1200000000,1000 {
+		opp-1200000000-1000 {
 			clock-latency-ns = <100000>;
 			opp-supported-hw = <0x04 0x0001>, <0x08 0x0002>,
 					   <0x08 0x0004>, <0x08 0x0008>,
@@ -331,7 +331,7 @@
 			opp-hz = /bits/ 64 <1200000000>;
 		};
 
-		opp@1200000000,1025 {
+		opp-1200000000-1025 {
 			clock-latency-ns = <100000>;
 			opp-supported-hw = <0x02 0x0001>, <0x04 0x0002>,
 					   <0x04 0x0004>, <0x04 0x0008>,
@@ -340,39 +340,39 @@
 			opp-hz = /bits/ 64 <1200000000>;
 		};
 
-		opp@1200000000,1050 {
+		opp-1200000000-1050 {
 			clock-latency-ns = <100000>;
 			opp-supported-hw = <0x02 0x019E>;
 			opp-hz = /bits/ 64 <1200000000>;
 		};
 
-		opp@1200000000,1075 {
+		opp-1200000000-1075 {
 			clock-latency-ns = <100000>;
 			opp-supported-hw = <0x01 0x0001>;
 			opp-hz = /bits/ 64 <1200000000>;
 		};
 
-		opp@1200000000,1100 {
+		opp-1200000000-1100 {
 			clock-latency-ns = <100000>;
 			opp-supported-hw = <0x01 0x0192>;
 			opp-hz = /bits/ 64 <1200000000>;
 		};
 
-		opp@1300000000,1000 {
+		opp-1300000000-1000 {
 			clock-latency-ns = <100000>;
 			opp-supported-hw = <0x08 0x0001>, <0x10 0x0080>,
 					   <0x10 0x0100>;
 			opp-hz = /bits/ 64 <1300000000>;
 		};
 
-		opp@1300000000,1025 {
+		opp-1300000000-1025 {
 			clock-latency-ns = <100000>;
 			opp-supported-hw = <0x04 0x0001>, <0x08 0x0002>,
 					   <0x08 0x0080>, <0x08 0x0100>;
 			opp-hz = /bits/ 64 <1300000000>;
 		};
 
-		opp@1300000000,1050 {
+		opp-1300000000-1050 {
 			clock-latency-ns = <100000>;
 			opp-supported-hw = <0x12 0x3061>, <0x04 0x0002>,
 					   <0x08 0x0004>, <0x08 0x0008>,
@@ -383,68 +383,68 @@
 			opp-hz = /bits/ 64 <1300000000>;
 		};
 
-		opp@1300000000,1075 {
+		opp-1300000000-1075 {
 			clock-latency-ns = <100000>;
 			opp-supported-hw = <0x02 0x0182>, <0x04 0x0004>,
 					   <0x04 0x0008>, <0x04 0x0010>;
 			opp-hz = /bits/ 64 <1300000000>;
 		};
 
-		opp@1300000000,1100 {
+		opp-1300000000-1100 {
 			clock-latency-ns = <100000>;
 			opp-supported-hw = <0x02 0x001C>;
 			opp-hz = /bits/ 64 <1300000000>;
 		};
 
-		opp@1300000000,1125 {
+		opp-1300000000-1125 {
 			clock-latency-ns = <100000>;
 			opp-supported-hw = <0x01 0x0001>;
 			opp-hz = /bits/ 64 <1300000000>;
 		};
 
-		opp@1300000000,1150 {
+		opp-1300000000-1150 {
 			clock-latency-ns = <100000>;
 			opp-supported-hw = <0x01 0x0182>;
 			opp-hz = /bits/ 64 <1300000000>;
 		};
 
-		opp@1300000000,1175 {
+		opp-1300000000-1175 {
 			clock-latency-ns = <100000>;
 			opp-supported-hw = <0x01 0x0010>;
 			opp-hz = /bits/ 64 <1300000000>;
 		};
 
-		opp@1400000000,1100 {
+		opp-1400000000-1100 {
 			clock-latency-ns = <100000>;
 			opp-supported-hw = <0x18 0x307C>;
 			opp-hz = /bits/ 64 <1400000000>;
 		};
 
-		opp@1400000000,1125 {
+		opp-1400000000-1125 {
 			clock-latency-ns = <100000>;
 			opp-supported-hw = <0x04 0x000C>;
 			opp-hz = /bits/ 64 <1400000000>;
 		};
 
-		opp@1400000000,1150 {
+		opp-1400000000-1150 {
 			clock-latency-ns = <100000>;
 			opp-supported-hw = <0x02 0x000C>, <0x04 0x0010>;
 			opp-hz = /bits/ 64 <1400000000>;
 		};
 
-		opp@1400000000,1175 {
+		opp-1400000000-1175 {
 			clock-latency-ns = <100000>;
 			opp-supported-hw = <0x02 0x0010>;
 			opp-hz = /bits/ 64 <1400000000>;
 		};
 
-		opp@1400000000,1237 {
+		opp-1400000000-1237 {
 			clock-latency-ns = <100000>;
 			opp-supported-hw = <0x01 0x0010>;
 			opp-hz = /bits/ 64 <1400000000>;
 		};
 
-		opp@1500000000,1125 {
+		opp-1500000000-1125 {
 			clock-latency-ns = <100000>;
 			opp-supported-hw = <0x08 0x0010>, <0x10 0x0020>,
 					   <0x10 0x0040>, <0x10 0x1000>,
@@ -452,7 +452,7 @@
 			opp-hz = /bits/ 64 <1500000000>;
 		};
 
-		opp@1500000000,1150 {
+		opp-1500000000-1150 {
 			clock-latency-ns = <100000>;
 			opp-supported-hw = <0x04 0x0010>, <0x08 0x0020>,
 					   <0x08 0x0040>, <0x08 0x1000>,
@@ -460,37 +460,37 @@
 			opp-hz = /bits/ 64 <1500000000>;
 		};
 
-		opp@1500000000,1200 {
+		opp-1500000000-1200 {
 			clock-latency-ns = <100000>;
 			opp-supported-hw = <0x02 0x0010>;
 			opp-hz = /bits/ 64 <1500000000>;
 		};
 
-		opp@1500000000,1237 {
+		opp-1500000000-1237 {
 			clock-latency-ns = <100000>;
 			opp-supported-hw = <0x01 0x0010>;
 			opp-hz = /bits/ 64 <1500000000>;
 		};
 
-		opp@1600000000,1212 {
+		opp-1600000000-1212 {
 			clock-latency-ns = <100000>;
 			opp-supported-hw = <0x10 0x3060>;
 			opp-hz = /bits/ 64 <1600000000>;
 		};
 
-		opp@1600000000,1237 {
+		opp-1600000000-1237 {
 			clock-latency-ns = <100000>;
 			opp-supported-hw = <0x08 0x3060>;
 			opp-hz = /bits/ 64 <1600000000>;
 		};
 
-		opp@1700000000,1212 {
+		opp-1700000000-1212 {
 			clock-latency-ns = <100000>;
 			opp-supported-hw = <0x10 0x3060>;
 			opp-hz = /bits/ 64 <1700000000>;
 		};
 
-		opp@1700000000,1237 {
+		opp-1700000000-1237 {
 			clock-latency-ns = <100000>;
 			opp-supported-hw = <0x08 0x3060>;
 			opp-hz = /bits/ 64 <1700000000>;
diff --git a/arch/arm/boot/dts/tegra30-ouya.dts b/arch/arm/boot/dts/tegra30-ouya.dts
index 4259871b76c9..b7acea39b942 100644
--- a/arch/arm/boot/dts/tegra30-ouya.dts
+++ b/arch/arm/boot/dts/tegra30-ouya.dts
@@ -68,22 +68,1936 @@
 		};
 	};
 
-	gpio: gpio@6000d000 {
-		gpio-ranges = <&pinmux 0 0 248>;
-		#reset-cells = <1>;
-	};
-
 	pinmux@70000868 {
 		pinctrl-names = "default";
 		pinctrl-0 = <&state_default>;
+
 		state_default: pinmux {
-			/* located at $state_default below */
+			clk_32k_out_pa0 {
+				nvidia,pins = "clk_32k_out_pa0";
+				nvidia,function = "blink";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			uart3_cts_n_pa1 {
+				nvidia,pins = "uart3_cts_n_pa1";
+				nvidia,function = "uartc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			dap2_fs_pa2 {
+				nvidia,pins = "dap2_fs_pa2";
+				nvidia,function = "i2s1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			dap2_sclk_pa3 {
+				nvidia,pins = "dap2_sclk_pa3";
+				nvidia,function = "i2s1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			dap2_din_pa4 {
+				nvidia,pins = "dap2_din_pa4";
+				nvidia,function = "i2s1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			dap2_dout_pa5 {
+				nvidia,pins = "dap2_dout_pa5";
+				nvidia,function = "i2s1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			sdmmc3_clk_pa6 {
+				nvidia,pins = "sdmmc3_clk_pa6";
+				nvidia,function = "sdmmc3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			sdmmc3_cmd_pa7 {
+				nvidia,pins = "sdmmc3_cmd_pa7";
+				nvidia,function = "sdmmc3";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			gmi_a17_pb0 {
+				nvidia,pins = "gmi_a17_pb0";
+				nvidia,function = "spi4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			gmi_a18_pb1 {
+				nvidia,pins = "gmi_a18_pb1";
+				nvidia,function = "spi4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			lcd_pwr0_pb2 {
+				nvidia,pins = "lcd_pwr0_pb2";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			lcd_pclk_pb3 {
+				nvidia,pins = "lcd_pclk_pb3";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			sdmmc3_dat3_pb4 {
+				nvidia,pins = "sdmmc3_dat3_pb4";
+				nvidia,function = "sdmmc3";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			sdmmc3_dat2_pb5 {
+				nvidia,pins = "sdmmc3_dat2_pb5";
+				nvidia,function = "sdmmc3";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			sdmmc3_dat1_pb6 {
+				nvidia,pins = "sdmmc3_dat1_pb6";
+				nvidia,function = "sdmmc3";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			sdmmc3_dat0_pb7 {
+				nvidia,pins = "sdmmc3_dat0_pb7";
+				nvidia,function = "sdmmc3";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			uart3_rts_n_pc0 {
+				nvidia,pins = "uart3_rts_n_pc0";
+				nvidia,function = "uartc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			lcd_pwr1_pc1 {
+				nvidia,pins = "lcd_pwr1_pc1";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			uart2_txd_pc2 {
+				nvidia,pins = "uart2_txd_pc2";
+				nvidia,function = "uartb";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			uart2_rxd_pc3 {
+				nvidia,pins = "uart2_rxd_pc3";
+				nvidia,function = "uartb";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			gen1_i2c_scl_pc4 {
+				nvidia,pins = "gen1_i2c_scl_pc4";
+				nvidia,function = "i2c1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+				nvidia,open-drain = <TEGRA_PIN_DISABLE>;
+			};
+
+			gen1_i2c_sda_pc5 {
+				nvidia,pins = "gen1_i2c_sda_pc5";
+				nvidia,function = "i2c1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+				nvidia,open-drain = <TEGRA_PIN_DISABLE>;
+			};
+
+			lcd_pwr2_pc6 {
+				nvidia,pins = "lcd_pwr2_pc6";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			gmi_wp_n_pc7 {
+				nvidia,pins = "gmi_wp_n_pc7";
+				nvidia,function = "gmi";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			sdmmc3_dat5_pd0 {
+				nvidia,pins = "sdmmc3_dat5_pd0";
+				nvidia,function = "sdmmc3";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			sdmmc3_dat4_pd1 {
+				nvidia,pins = "sdmmc3_dat4_pd1";
+				nvidia,function = "sdmmc3";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			lcd_dc1_pd2 {
+				nvidia,pins = "lcd_dc1_pd2";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			sdmmc3_dat6_pd3 {
+				nvidia,pins = "sdmmc3_dat6_pd3";
+				nvidia,function = "spi4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			sdmmc3_dat7_pd4 {
+				nvidia,pins = "sdmmc3_dat7_pd4";
+				nvidia,function = "spi4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			vi_d1_pd5 {
+				nvidia,pins = "vi_d1_pd5";
+				nvidia,function = "sdmmc2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			vi_vsync_pd6 {
+				nvidia,pins = "vi_vsync_pd6";
+				nvidia,function = "ddr";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			vi_hsync_pd7 {
+				nvidia,pins = "vi_hsync_pd7";
+				nvidia,function = "ddr";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			lcd_d0_pe0 {
+				nvidia,pins = "lcd_d0_pe0";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			lcd_d1_pe1 {
+				nvidia,pins = "lcd_d1_pe1";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			lcd_d2_pe2 {
+				nvidia,pins = "lcd_d2_pe2";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			lcd_d3_pe3 {
+				nvidia,pins = "lcd_d3_pe3";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			lcd_d4_pe4 {
+				nvidia,pins = "lcd_d4_pe4";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			lcd_d5_pe5 {
+				nvidia,pins = "lcd_d5_pe5";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			lcd_d6_pe6 {
+				nvidia,pins = "lcd_d6_pe6";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			lcd_d7_pe7 {
+				nvidia,pins = "lcd_d7_pe7";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			lcd_d8_pf0 {
+				nvidia,pins = "lcd_d8_pf0";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			lcd_d9_pf1 {
+				nvidia,pins = "lcd_d9_pf1";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			lcd_d10_pf2 {
+				nvidia,pins = "lcd_d10_pf2";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			lcd_d11_pf3 {
+				nvidia,pins = "lcd_d11_pf3";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			lcd_d12_pf4 {
+				nvidia,pins = "lcd_d12_pf4";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			lcd_d13_pf5 {
+				nvidia,pins = "lcd_d13_pf5";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			lcd_d14_pf6 {
+				nvidia,pins = "lcd_d14_pf6";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			lcd_d15_pf7 {
+				nvidia,pins = "lcd_d15_pf7";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			gmi_ad0_pg0 {
+				nvidia,pins = "gmi_ad0_pg0";
+				nvidia,function = "nand";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			gmi_ad1_pg1 {
+				nvidia,pins = "gmi_ad1_pg1";
+				nvidia,function = "nand";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			gmi_ad2_pg2 {
+				nvidia,pins = "gmi_ad2_pg2";
+				nvidia,function = "nand";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			gmi_ad3_pg3 {
+				nvidia,pins = "gmi_ad3_pg3";
+				nvidia,function = "nand";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			gmi_ad4_pg4 {
+				nvidia,pins = "gmi_ad4_pg4";
+				nvidia,function = "nand";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			gmi_ad5_pg5 {
+				nvidia,pins = "gmi_ad5_pg5";
+				nvidia,function = "nand";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			gmi_ad6_pg6 {
+				nvidia,pins = "gmi_ad6_pg6";
+				nvidia,function = "nand";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			gmi_ad7_pg7 {
+				nvidia,pins = "gmi_ad7_pg7";
+				nvidia,function = "nand";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			gmi_ad8_ph0 {
+				nvidia,pins = "gmi_ad8_ph0";
+				nvidia,function = "pwm0";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			gmi_ad9_ph1 {
+				nvidia,pins = "gmi_ad9_ph1";
+				nvidia,function = "pwm1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			gmi_ad10_ph2 {
+				nvidia,pins = "gmi_ad10_ph2";
+				nvidia,function = "pwm2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			gmi_ad11_ph3 {
+				nvidia,pins = "gmi_ad11_ph3";
+				nvidia,function = "nand";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			gmi_ad12_ph4 {
+				nvidia,pins = "gmi_ad12_ph4";
+				nvidia,function = "nand";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			gmi_ad13_ph5 {
+				nvidia,pins = "gmi_ad13_ph5";
+				nvidia,function = "nand";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			gmi_ad14_ph6 {
+				nvidia,pins = "gmi_ad14_ph6";
+				nvidia,function = "nand";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			gmi_wr_n_pi0 {
+				nvidia,pins = "gmi_wr_n_pi0";
+				nvidia,function = "nand";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			gmi_oe_n_pi1 {
+				nvidia,pins = "gmi_oe_n_pi1";
+				nvidia,function = "nand";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			gmi_dqs_pi2 {
+				nvidia,pins = "gmi_dqs_pi2";
+				nvidia,function = "nand";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			gmi_iordy_pi5 {
+				nvidia,pins = "gmi_iordy_pi5";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			gmi_cs7_n_pi6 {
+				nvidia,pins = "gmi_cs7_n_pi6";
+				nvidia,function = "nand";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			gmi_wait_pi7 {
+				nvidia,pins = "gmi_wait_pi7";
+				nvidia,function = "nand";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			lcd_de_pj1 {
+				nvidia,pins = "lcd_de_pj1";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			gmi_cs1_n_pj2 {
+				nvidia,pins = "gmi_cs1_n_pj2";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			lcd_hsync_pj3 {
+				nvidia,pins = "lcd_hsync_pj3";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			lcd_vsync_pj4 {
+				nvidia,pins = "lcd_vsync_pj4";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			uart2_cts_n_pj5 {
+				nvidia,pins = "uart2_cts_n_pj5";
+				nvidia,function = "uartb";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			uart2_rts_n_pj6 {
+				nvidia,pins = "uart2_rts_n_pj6";
+				nvidia,function = "uartb";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			gmi_a16_pj7 {
+				nvidia,pins = "gmi_a16_pj7";
+				nvidia,function = "spi4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			gmi_adv_n_pk0 {
+				nvidia,pins = "gmi_adv_n_pk0";
+				nvidia,function = "nand";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			gmi_clk_pk1 {
+				nvidia,pins = "gmi_clk_pk1";
+				nvidia,function = "nand";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			gmi_cs2_n_pk3 {
+				nvidia,pins = "gmi_cs2_n_pk3";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			gmi_cs3_n_pk4 {
+				nvidia,pins = "gmi_cs3_n_pk4";
+				nvidia,function = "nand";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			spdif_out_pk5 {
+				nvidia,pins = "spdif_out_pk5";
+				nvidia,function = "spdif";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			spdif_in_pk6 {
+				nvidia,pins = "spdif_in_pk6";
+				nvidia,function = "spdif";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			gmi_a19_pk7 {
+				nvidia,pins = "gmi_a19_pk7";
+				nvidia,function = "spi4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			vi_d2_pl0 {
+				nvidia,pins = "vi_d2_pl0";
+				nvidia,function = "sdmmc2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			vi_d3_pl1 {
+				nvidia,pins = "vi_d3_pl1";
+				nvidia,function = "sdmmc2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			vi_d4_pl2 {
+				nvidia,pins = "vi_d4_pl2";
+				nvidia,function = "vi";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			vi_d5_pl3 {
+				nvidia,pins = "vi_d5_pl3";
+				nvidia,function = "sdmmc2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			vi_d6_pl4 {
+				nvidia,pins = "vi_d6_pl4";
+				nvidia,function = "vi";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			vi_d7_pl5 {
+				nvidia,pins = "vi_d7_pl5";
+				nvidia,function = "sdmmc2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			vi_d8_pl6 {
+				nvidia,pins = "vi_d8_pl6";
+				nvidia,function = "sdmmc2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			vi_d9_pl7 {
+				nvidia,pins = "vi_d9_pl7";
+				nvidia,function = "sdmmc2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			lcd_d16_pm0 {
+				nvidia,pins = "lcd_d16_pm0";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			lcd_d17_pm1 {
+				nvidia,pins = "lcd_d17_pm1";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			lcd_d18_pm2 {
+				nvidia,pins = "lcd_d18_pm2";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			lcd_d19_pm3 {
+				nvidia,pins = "lcd_d19_pm3";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			lcd_d20_pm4 {
+				nvidia,pins = "lcd_d20_pm4";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			lcd_d21_pm5 {
+				nvidia,pins = "lcd_d21_pm5";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			lcd_d22_pm6 {
+				nvidia,pins = "lcd_d22_pm6";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			lcd_d23_pm7 {
+				nvidia,pins = "lcd_d23_pm7";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			dap1_fs_pn0 {
+				nvidia,pins = "dap1_fs_pn0";
+				nvidia,function = "i2s0";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			dap1_din_pn1 {
+				nvidia,pins = "dap1_din_pn1";
+				nvidia,function = "i2s0";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			dap1_dout_pn2 {
+				nvidia,pins = "dap1_dout_pn2";
+				nvidia,function = "i2s0";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			dap1_sclk_pn3 {
+				nvidia,pins = "dap1_sclk_pn3";
+				nvidia,function = "i2s0";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			lcd_cs0_n_pn4 {
+				nvidia,pins = "lcd_cs0_n_pn4";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			lcd_sdout_pn5 {
+				nvidia,pins = "lcd_sdout_pn5";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			lcd_dc0_pn6 {
+				nvidia,pins = "lcd_dc0_pn6";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			hdmi_int_pn7 {
+				nvidia,pins = "hdmi_int_pn7";
+				nvidia,function = "hdmi";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			ulpi_data7_po0 {
+				nvidia,pins = "ulpi_data7_po0";
+				nvidia,function = "uarta";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			ulpi_data0_po1 {
+				nvidia,pins = "ulpi_data0_po1";
+				nvidia,function = "uarta";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			ulpi_data1_po2 {
+				nvidia,pins = "ulpi_data1_po2";
+				nvidia,function = "uarta";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			ulpi_data2_po3 {
+				nvidia,pins = "ulpi_data2_po3";
+				nvidia,function = "uarta";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			ulpi_data3_po4 {
+				nvidia,pins = "ulpi_data3_po4";
+				nvidia,function = "uarta";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			ulpi_data4_po5 {
+				nvidia,pins = "ulpi_data4_po5";
+				nvidia,function = "uarta";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			ulpi_data5_po6 {
+				nvidia,pins = "ulpi_data5_po6";
+				nvidia,function = "uarta";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			ulpi_data6_po7 {
+				nvidia,pins = "ulpi_data6_po7";
+				nvidia,function = "uarta";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			dap3_fs_pp0 {
+				nvidia,pins = "dap3_fs_pp0";
+				nvidia,function = "i2s2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			dap3_din_pp1 {
+				nvidia,pins = "dap3_din_pp1";
+				nvidia,function = "i2s2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			dap3_dout_pp2 {
+				nvidia,pins = "dap3_dout_pp2";
+				nvidia,function = "i2s2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			dap3_sclk_pp3 {
+				nvidia,pins = "dap3_sclk_pp3";
+				nvidia,function = "i2s2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			dap4_fs_pp4 {
+				nvidia,pins = "dap4_fs_pp4";
+				nvidia,function = "i2s3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			dap4_din_pp5 {
+				nvidia,pins = "dap4_din_pp5";
+				nvidia,function = "i2s3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			dap4_dout_pp6 {
+				nvidia,pins = "dap4_dout_pp6";
+				nvidia,function = "i2s3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			dap4_sclk_pp7 {
+				nvidia,pins = "dap4_sclk_pp7";
+				nvidia,function = "i2s3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			kb_col0_pq0 {
+				nvidia,pins = "kb_col0_pq0";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			kb_col1_pq1 {
+				nvidia,pins = "kb_col1_pq1";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			kb_col2_pq2 {
+				nvidia,pins = "kb_col2_pq2";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			kb_col3_pq3 {
+				nvidia,pins = "kb_col3_pq3";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			kb_col4_pq4 {
+				nvidia,pins = "kb_col4_pq4";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			kb_col5_pq5 {
+				nvidia,pins = "kb_col5_pq5";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			kb_col6_pq6 {
+				nvidia,pins = "kb_col6_pq6";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			kb_col7_pq7 {
+				nvidia,pins = "kb_col7_pq7";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			kb_row0_pr0 {
+				nvidia,pins = "kb_row0_pr0";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			kb_row1_pr1 {
+				nvidia,pins = "kb_row1_pr1";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			kb_row2_pr2 {
+				nvidia,pins = "kb_row2_pr2";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			kb_row3_pr3 {
+				nvidia,pins = "kb_row3_pr3";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			kb_row4_pr4 {
+				nvidia,pins = "kb_row4_pr4";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			kb_row5_pr5 {
+				nvidia,pins = "kb_row5_pr5";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			kb_row6_pr6 {
+				nvidia,pins = "kb_row6_pr6";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			kb_row7_pr7 {
+				nvidia,pins = "kb_row7_pr7";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			kb_row8_ps0 {
+				nvidia,pins = "kb_row8_ps0";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			kb_row9_ps1 {
+				nvidia,pins = "kb_row9_ps1";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			kb_row10_ps2 {
+				nvidia,pins = "kb_row10_ps2";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			kb_row11_ps3 {
+				nvidia,pins = "kb_row11_ps3";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			kb_row12_ps4 {
+				nvidia,pins = "kb_row12_ps4";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			kb_row13_ps5 {
+				nvidia,pins = "kb_row13_ps5";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			kb_row14_ps6 {
+				nvidia,pins = "kb_row14_ps6";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			kb_row15_ps7 {
+				nvidia,pins = "kb_row15_ps7";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			vi_pclk_pt0 {
+				nvidia,pins = "vi_pclk_pt0";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			vi_mclk_pt1 {
+				nvidia,pins = "vi_mclk_pt1";
+				nvidia,function = "vi";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			vi_d10_pt2 {
+				nvidia,pins = "vi_d10_pt2";
+				nvidia,function = "ddr";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			vi_d11_pt3 {
+				nvidia,pins = "vi_d11_pt3";
+				nvidia,function = "ddr";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			vi_d0_pt4 {
+				nvidia,pins = "vi_d0_pt4";
+				nvidia,function = "ddr";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			gen2_i2c_scl_pt5 {
+				nvidia,pins = "gen2_i2c_scl_pt5";
+				nvidia,function = "i2c2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+				nvidia,open-drain = <TEGRA_PIN_DISABLE>;
+			};
+
+			gen2_i2c_sda_pt6 {
+				nvidia,pins = "gen2_i2c_sda_pt6";
+				nvidia,function = "i2c2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+				nvidia,open-drain = <TEGRA_PIN_DISABLE>;
+			};
+
+			sdmmc4_cmd_pt7 {
+				nvidia,pins = "sdmmc4_cmd_pt7";
+				nvidia,function = "sdmmc4";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,io-reset = <TEGRA_PIN_DISABLE>;
+			};
+
+			pu0 {
+				nvidia,pins = "pu0";
+				nvidia,function = "owr";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pu1 {
+				nvidia,pins = "pu1";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pu2 {
+				nvidia,pins = "pu2";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pu3 {
+				nvidia,pins = "pu3";
+				nvidia,function = "pwm0";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pu4 {
+				nvidia,pins = "pu4";
+				nvidia,function = "pwm1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pu5 {
+				nvidia,pins = "pu5";
+				nvidia,function = "rsvd4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pu6 {
+				nvidia,pins = "pu6";
+				nvidia,function = "pwm3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			jtag_rtck_pu7 {
+				nvidia,pins = "jtag_rtck_pu7";
+				nvidia,function = "rtck";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pv0 {
+				nvidia,pins = "pv0";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			pv1 {
+				nvidia,pins = "pv1";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pv2 {
+				nvidia,pins = "pv2";
+				nvidia,function = "owr";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pv3 {
+				nvidia,pins = "pv3";
+				nvidia,function = "clk_12m_out";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			ddc_scl_pv4 {
+				nvidia,pins = "ddc_scl_pv4";
+				nvidia,function = "i2c4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			ddc_sda_pv5 {
+				nvidia,pins = "ddc_sda_pv5";
+				nvidia,function = "i2c4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			crt_hsync_pv6 {
+				nvidia,pins = "crt_hsync_pv6";
+				nvidia,function = "crt";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			crt_vsync_pv7 {
+				nvidia,pins = "crt_vsync_pv7";
+				nvidia,function = "crt";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			lcd_cs1_n_pw0 {
+				nvidia,pins = "lcd_cs1_n_pw0";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			lcd_m1_pw1 {
+				nvidia,pins = "lcd_m1_pw1";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			spi2_cs1_n_pw2 {
+				nvidia,pins = "spi2_cs1_n_pw2";
+				nvidia,function = "spi2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			clk1_out_pw4 {
+				nvidia,pins = "clk1_out_pw4";
+				nvidia,function = "extperiph1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			clk2_out_pw5 {
+				nvidia,pins = "clk2_out_pw5";
+				nvidia,function = "extperiph2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			uart3_txd_pw6 {
+				nvidia,pins = "uart3_txd_pw6";
+				nvidia,function = "uartc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			uart3_rxd_pw7 {
+				nvidia,pins = "uart3_rxd_pw7";
+				nvidia,function = "uartc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			spi2_sck_px2 {
+				nvidia,pins = "spi2_sck_px2";
+				nvidia,function = "gmi";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			spi1_mosi_px4 {
+				nvidia,pins = "spi1_mosi_px4";
+				nvidia,function = "spi1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			spi1_sck_px5 {
+				nvidia,pins = "spi1_sck_px5";
+				nvidia,function = "spi1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			spi1_cs0_n_px6 {
+				nvidia,pins = "spi1_cs0_n_px6";
+				nvidia,function = "spi1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			spi1_miso_px7 {
+				nvidia,pins = "spi1_miso_px7";
+				nvidia,function = "spi1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			ulpi_clk_py0 {
+				nvidia,pins = "ulpi_clk_py0";
+				nvidia,function = "uartd";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			ulpi_dir_py1 {
+				nvidia,pins = "ulpi_dir_py1";
+				nvidia,function = "uartd";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			ulpi_nxt_py2 {
+				nvidia,pins = "ulpi_nxt_py2";
+				nvidia,function = "uartd";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			ulpi_stp_py3 {
+				nvidia,pins = "ulpi_stp_py3";
+				nvidia,function = "uartd";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			sdmmc1_dat3_py4 {
+				nvidia,pins = "sdmmc1_dat3_py4";
+				nvidia,function = "sdmmc1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			sdmmc1_dat2_py5 {
+				nvidia,pins = "sdmmc1_dat2_py5";
+				nvidia,function = "sdmmc1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			sdmmc1_dat1_py6 {
+				nvidia,pins = "sdmmc1_dat1_py6";
+				nvidia,function = "sdmmc1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			sdmmc1_dat0_py7 {
+				nvidia,pins = "sdmmc1_dat0_py7";
+				nvidia,function = "sdmmc1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			sdmmc1_clk_pz0 {
+				nvidia,pins = "sdmmc1_clk_pz0";
+				nvidia,function = "sdmmc1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			sdmmc1_cmd_pz1 {
+				nvidia,pins = "sdmmc1_cmd_pz1";
+				nvidia,function = "sdmmc1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			lcd_sdin_pz2 {
+				nvidia,pins = "lcd_sdin_pz2";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			lcd_wr_n_pz3 {
+				nvidia,pins = "lcd_wr_n_pz3";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			lcd_sck_pz4 {
+				nvidia,pins = "lcd_sck_pz4";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			sys_clk_req_pz5 {
+				nvidia,pins = "sys_clk_req_pz5";
+				nvidia,function = "sysclk";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pwr_i2c_scl_pz6 {
+				nvidia,pins = "pwr_i2c_scl_pz6";
+				nvidia,function = "i2cpwr";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,open-drain = <TEGRA_PIN_ENABLE>;
+			};
+
+			pwr_i2c_sda_pz7 {
+				nvidia,pins = "pwr_i2c_sda_pz7";
+				nvidia,function = "i2cpwr";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,open-drain = <TEGRA_PIN_ENABLE>;
+			};
+
+			sdmmc4_dat0_paa0 {
+				nvidia,pins = "sdmmc4_dat0_paa0";
+				nvidia,function = "sdmmc4";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,io-reset = <TEGRA_PIN_DISABLE>;
+			};
+
+			sdmmc4_dat1_paa1 {
+				nvidia,pins = "sdmmc4_dat1_paa1";
+				nvidia,function = "sdmmc4";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,io-reset = <TEGRA_PIN_DISABLE>;
+			};
+
+			sdmmc4_dat2_paa2 {
+				nvidia,pins = "sdmmc4_dat2_paa2";
+				nvidia,function = "sdmmc4";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,io-reset = <TEGRA_PIN_DISABLE>;
+			};
+
+			sdmmc4_dat3_paa3 {
+				nvidia,pins = "sdmmc4_dat3_paa3";
+				nvidia,function = "sdmmc4";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,io-reset = <TEGRA_PIN_DISABLE>;
+			};
+
+			sdmmc4_dat4_paa4 {
+				nvidia,pins = "sdmmc4_dat4_paa4";
+				nvidia,function = "sdmmc4";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,io-reset = <TEGRA_PIN_DISABLE>;
+			};
+
+			sdmmc4_dat5_paa5 {
+				nvidia,pins = "sdmmc4_dat5_paa5";
+				nvidia,function = "sdmmc4";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,io-reset = <TEGRA_PIN_DISABLE>;
+			};
+
+			sdmmc4_dat6_paa6 {
+				nvidia,pins = "sdmmc4_dat6_paa6";
+				nvidia,function = "sdmmc4";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,io-reset = <TEGRA_PIN_DISABLE>;
+			};
+
+			sdmmc4_dat7_paa7 {
+				nvidia,pins = "sdmmc4_dat7_paa7";
+				nvidia,function = "sdmmc4";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,io-reset = <TEGRA_PIN_DISABLE>;
+			};
+
+			pbb0 {
+				nvidia,pins = "pbb0";
+				nvidia,function = "i2s4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			cam_i2c_scl_pbb1 {
+				nvidia,pins = "cam_i2c_scl_pbb1";
+				nvidia,function = "i2c3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+				nvidia,open-drain = <TEGRA_PIN_DISABLE>;
+			};
+
+			cam_i2c_sda_pbb2 {
+				nvidia,pins = "cam_i2c_sda_pbb2";
+				nvidia,function = "i2c3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+				nvidia,open-drain = <TEGRA_PIN_DISABLE>;
+			};
+
+			pbb3 {
+				nvidia,pins = "pbb3";
+				nvidia,function = "vgp3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pbb4 {
+				nvidia,pins = "pbb4";
+				nvidia,function = "vgp4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pbb5 {
+				nvidia,pins = "pbb5";
+				nvidia,function = "vgp5";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pbb6 {
+				nvidia,pins = "pbb6";
+				nvidia,function = "vgp6";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pbb7 {
+				nvidia,pins = "pbb7";
+				nvidia,function = "i2s4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			cam_mclk_pcc0 {
+				nvidia,pins = "cam_mclk_pcc0";
+				nvidia,function = "vi_alt3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			pcc1 {
+				nvidia,pins = "pcc1";
+				nvidia,function = "i2s4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			pcc2 {
+				nvidia,pins = "pcc2";
+				nvidia,function = "i2s4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			sdmmc4_rst_n_pcc3 {
+				nvidia,pins = "sdmmc4_rst_n_pcc3";
+				nvidia,function = "sdmmc4";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,io-reset = <TEGRA_PIN_DISABLE>;
+			};
+
+			sdmmc4_clk_pcc4 {
+				nvidia,pins = "sdmmc4_clk_pcc4";
+				nvidia,function = "sdmmc4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,io-reset = <TEGRA_PIN_DISABLE>;
+			};
+
+			clk2_req_pcc5 {
+				nvidia,pins = "clk2_req_pcc5";
+				nvidia,function = "dap";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pex_l2_rst_n_pcc6 {
+				nvidia,pins = "pex_l2_rst_n_pcc6";
+				nvidia,function = "pcie";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pex_l2_clkreq_n_pcc7 {
+				nvidia,pins = "pex_l2_clkreq_n_pcc7";
+				nvidia,function = "pcie";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pex_l0_prsnt_n_pdd0 {
+				nvidia,pins = "pex_l0_prsnt_n_pdd0";
+				nvidia,function = "pcie";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pex_l0_rst_n_pdd1 {
+				nvidia,pins = "pex_l0_rst_n_pdd1";
+				nvidia,function = "pcie";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pex_l0_clkreq_n_pdd2 {
+				nvidia,pins = "pex_l0_clkreq_n_pdd2";
+				nvidia,function = "pcie";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pex_wake_n_pdd3 {
+				nvidia,pins = "pex_wake_n_pdd3";
+				nvidia,function = "pcie";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pex_l1_prsnt_n_pdd4 {
+				nvidia,pins = "pex_l1_prsnt_n_pdd4";
+				nvidia,function = "pcie";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pex_l1_rst_n_pdd5 {
+				nvidia,pins = "pex_l1_rst_n_pdd5";
+				nvidia,function = "pcie";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pex_l1_clkreq_n_pdd6 {
+				nvidia,pins = "pex_l1_clkreq_n_pdd6";
+				nvidia,function = "pcie";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pex_l2_prsnt_n_pdd7 {
+				nvidia,pins = "pex_l2_prsnt_n_pdd7";
+				nvidia,function = "pcie";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			clk3_out_pee0 {
+				nvidia,pins = "clk3_out_pee0";
+				nvidia,function = "extperiph3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			clk3_req_pee1 {
+				nvidia,pins = "clk3_req_pee1";
+				nvidia,function = "dev3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			clk1_req_pee2 {
+				nvidia,pins = "clk1_req_pee2";
+				nvidia,function = "dap";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			hdmi_cec_pee3 {
+				nvidia,pins = "hdmi_cec_pee3";
+				nvidia,function = "cec";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,open-drain = <TEGRA_PIN_DISABLE>;
+			};
+
+			owr {
+				nvidia,pins = "owr";
+				nvidia,function = "owr";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			drive_groups {
+				nvidia,pins = "drive_gma",
+					      "drive_gmb",
+					      "drive_gmc",
+					      "drive_gmd";
+				nvidia,pull-down-strength = <9>;
+				nvidia,pull-up-strength = <9>;
+				nvidia,slew-rate-rising = <TEGRA_PIN_SLEW_RATE_SLOWEST>;
+				nvidia,slew-rate-falling = <TEGRA_PIN_SLEW_RATE_SLOWEST>;
+			};
 		};
 	};
 
 	uartc: serial@70006200 {
-		status = "okay";
 		compatible = "nvidia,tegra30-hsuart";
+		/delete-property/ reg-shift;
+		status = "okay";
 
 		nvidia,adjust-baud-rates = <0 9600 100>,
 					   <9600 115200 200>,
@@ -277,14 +2191,2294 @@
 		nvidia,core-pwr-off-time = <458>;
 		nvidia,core-power-req-active-high;
 		nvidia,sys-clock-req-active-high;
+		core-supply = <&vdd_core>;
 	};
 
-	mc_timings: memory-controller@7000f000 {
-		/* timings located at &mc_timings below */
+	memory-controller@7000f000 {
+		emc-timings-0 {
+			nvidia,ram-code = <0>; /* Samsung RAM */
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+				nvidia,emem-configuration = <
+					0x00030003 /* MC_EMEM_ARB_CFG */
+					0xc0000010 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000001 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000001 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06020102 /* MC_EMEM_ARB_DA_TURNS */
+					0x000a0502 /* MC_EMEM_ARB_DA_COVERS */
+					0x75830303 /* MC_EMEM_ARB_MISC0 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+				nvidia,emem-configuration = <
+					0x00010003 /* MC_EMEM_ARB_CFG */
+					0xc0000010 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000001 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000001 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06020102 /* MC_EMEM_ARB_DA_TURNS */
+					0x000a0502 /* MC_EMEM_ARB_DA_COVERS */
+					0x74630303 /* MC_EMEM_ARB_MISC0 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+				nvidia,emem-configuration = <
+					0x00000003 /* MC_EMEM_ARB_CFG */
+					0xc0000018 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000002 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000001 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06020102 /* MC_EMEM_ARB_DA_TURNS */
+					0x000a0503 /* MC_EMEM_ARB_DA_COVERS */
+					0x73c30504 /* MC_EMEM_ARB_MISC0 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+				nvidia,emem-configuration = <
+					0x00000006 /* MC_EMEM_ARB_CFG */
+					0xc0000025 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000005 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000004 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000001 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06020102 /* MC_EMEM_ARB_DA_TURNS */
+					0x000a0505 /* MC_EMEM_ARB_DA_COVERS */
+					0x73840a06 /* MC_EMEM_ARB_MISC0 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-400000000 {
+				clock-frequency = <400000000>;
+				nvidia,emem-configuration = <
+					0x0000000c /* MC_EMEM_ARB_CFG */
+					0xc0000048 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000009 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000005 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000007 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000003 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06030202 /* MC_EMEM_ARB_DA_TURNS */
+					0x000d0709 /* MC_EMEM_ARB_DA_COVERS */
+					0x7086120a /* MC_EMEM_ARB_MISC0 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-800000000 {
+				clock-frequency = <800000000>;
+				nvidia,emem-configuration = <
+					0x00000018 /* MC_EMEM_ARB_CFG */
+					0xc0000090 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000004 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000005 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000013 /* MC_EMEM_ARB_TIMING_RC */
+					0x0000000c /* MC_EMEM_ARB_TIMING_RAS */
+					0x0000000f /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x0000000c /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000004 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000008 /* MC_EMEM_ARB_TIMING_W2R */
+					0x08040202 /* MC_EMEM_ARB_DA_TURNS */
+					0x00160d13 /* MC_EMEM_ARB_DA_COVERS */
+					0x712c2414 /* MC_EMEM_ARB_MISC0 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+		};
+
+		emc-timings-1 {
+			nvidia,ram-code = <1>; /* Hynix M RAM */
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+				nvidia,emem-configuration = <
+					0x00030003 /* MC_EMEM_ARB_CFG */
+					0xc0000010 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000001 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000001 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06020102 /* MC_EMEM_ARB_DA_TURNS */
+					0x000a0502 /* MC_EMEM_ARB_DA_COVERS */
+					0x75830303 /* MC_EMEM_ARB_MISC0 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+				nvidia,emem-configuration = <
+					0x00010003 /* MC_EMEM_ARB_CFG */
+					0xc0000010 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000001 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000001 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06020102 /* MC_EMEM_ARB_DA_TURNS */
+					0x000a0502 /* MC_EMEM_ARB_DA_COVERS */
+					0x74630303 /* MC_EMEM_ARB_MISC0 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+				nvidia,emem-configuration = <
+					0x00000003 /* MC_EMEM_ARB_CFG */
+					0xc0000018 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000002 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000001 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06020102 /* MC_EMEM_ARB_DA_TURNS */
+					0x000a0503 /* MC_EMEM_ARB_DA_COVERS */
+					0x73c30504 /* MC_EMEM_ARB_MISC0 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+				nvidia,emem-configuration = <
+					0x00000006 /* MC_EMEM_ARB_CFG */
+					0xc0000025 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000005 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000004 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000001 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06020102 /* MC_EMEM_ARB_DA_TURNS */
+					0x000a0505 /* MC_EMEM_ARB_DA_COVERS */
+					0x73840a06 /* MC_EMEM_ARB_MISC0 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-400000000 {
+				clock-frequency = <400000000>;
+				nvidia,emem-configuration = <
+					0x0000000c /* MC_EMEM_ARB_CFG */
+					0xc0000048 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000009 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000005 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000007 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000003 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06030202 /* MC_EMEM_ARB_DA_TURNS */
+					0x000d0709 /* MC_EMEM_ARB_DA_COVERS */
+					0x7086120a /* MC_EMEM_ARB_MISC0 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-800000000 {
+				clock-frequency = <800000000>;
+				nvidia,emem-configuration = <
+					0x00000018 /* MC_EMEM_ARB_CFG */
+					0xc0000090 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000004 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000005 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000013 /* MC_EMEM_ARB_TIMING_RC */
+					0x0000000c /* MC_EMEM_ARB_TIMING_RAS */
+					0x0000000f /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x0000000c /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000004 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000008 /* MC_EMEM_ARB_TIMING_W2R */
+					0x08040202 /* MC_EMEM_ARB_DA_TURNS */
+					0x00160d13 /* MC_EMEM_ARB_DA_COVERS */
+					0x712c2414 /* MC_EMEM_ARB_MISC0 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+		};
+
+		emc-timings-2 {
+			nvidia,ram-code = <2>; /* Hynix A RAM */
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+				nvidia,emem-configuration = <
+					0x00030003 /* MC_EMEM_ARB_CFG */
+					0xc0000010 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000001 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000001 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06020102 /* MC_EMEM_ARB_DA_TURNS */
+					0x000a0502 /* MC_EMEM_ARB_DA_COVERS */
+					0x75e30303 /* MC_EMEM_ARB_MISC0 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+				nvidia,emem-configuration = <
+					0x00010003 /* MC_EMEM_ARB_CFG */
+					0xc0000010 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000001 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000001 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06020102 /* MC_EMEM_ARB_DA_TURNS */
+					0x000a0502 /* MC_EMEM_ARB_DA_COVERS */
+					0x74e30303 /* MC_EMEM_ARB_MISC0 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+				nvidia,emem-configuration = <
+					0x00000003 /* MC_EMEM_ARB_CFG */
+					0xc0000018 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000002 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000001 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06020102 /* MC_EMEM_ARB_DA_TURNS */
+					0x000a0503 /* MC_EMEM_ARB_DA_COVERS */
+					0x74430504 /* MC_EMEM_ARB_MISC0 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+				nvidia,emem-configuration = <
+					0x00000006 /* MC_EMEM_ARB_CFG */
+					0xc0000025 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000005 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000004 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000001 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06020102 /* MC_EMEM_ARB_DA_TURNS */
+					0x000a0505 /* MC_EMEM_ARB_DA_COVERS */
+					0x74040a06 /* MC_EMEM_ARB_MISC0 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-400000000 {
+				clock-frequency = <400000000>;
+				nvidia,emem-configuration = <
+					0x0000000c /* MC_EMEM_ARB_CFG */
+					0xc0000048 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000009 /* MC_EMEM_ARB_TIMING_RC */
+					0x00000005 /* MC_EMEM_ARB_TIMING_RAS */
+					0x00000007 /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000003 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
+					0x06030202 /* MC_EMEM_ARB_DA_TURNS */
+					0x000d0709 /* MC_EMEM_ARB_DA_COVERS */
+					0x7086120a /* MC_EMEM_ARB_MISC0 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+
+			timing-800000000 {
+				clock-frequency = <800000000>;
+				nvidia,emem-configuration = <
+					0x00000018 /* MC_EMEM_ARB_CFG */
+					0xc0000090 /* MC_EMEM_ARB_OUTSTANDING_REQ */
+					0x00000004 /* MC_EMEM_ARB_TIMING_RCD */
+					0x00000005 /* MC_EMEM_ARB_TIMING_RP */
+					0x00000013 /* MC_EMEM_ARB_TIMING_RC */
+					0x0000000c /* MC_EMEM_ARB_TIMING_RAS */
+					0x0000000f /* MC_EMEM_ARB_TIMING_FAW */
+					0x00000002 /* MC_EMEM_ARB_TIMING_RRD */
+					0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
+					0x0000000c /* MC_EMEM_ARB_TIMING_WAP2PRE */
+					0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
+					0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
+					0x00000004 /* MC_EMEM_ARB_TIMING_R2W */
+					0x00000008 /* MC_EMEM_ARB_TIMING_W2R */
+					0x08040202 /* MC_EMEM_ARB_DA_TURNS */
+					0x00160d13 /* MC_EMEM_ARB_DA_COVERS */
+					0x712c2414 /* MC_EMEM_ARB_MISC0 */
+					0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
+				>;
+			};
+		};
 	};
 
-	emc_timings: memory-controller@7000f400 {
-		/* timings located at &emc_timings below */
+	memory-controller@7000f400 {
+		emc-timings-0 {
+			nvidia,ram-code = <0>;  /* Samsung RAM */
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200008>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-periodic-qrst;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-configuration = <
+					0x00000001 /* EMC_RC */
+					0x00000006 /* EMC_RFC */
+					0x00000000 /* EMC_RAS */
+					0x00000000 /* EMC_RP */
+					0x00000002 /* EMC_R2W */
+					0x0000000a /* EMC_W2R */
+					0x00000005 /* EMC_R2P */
+					0x0000000b /* EMC_W2P */
+					0x00000000 /* EMC_RD_RCD */
+					0x00000000 /* EMC_WR_RCD */
+					0x00000003 /* EMC_RRD */
+					0x00000001 /* EMC_REXT */
+					0x00000000 /* EMC_WEXT */
+					0x00000005 /* EMC_WDV */
+					0x00000005 /* EMC_QUSE */
+					0x00000004 /* EMC_QRST */
+					0x0000000a /* EMC_QSAFE */
+					0x0000000b /* EMC_RDV */
+					0x000000c0 /* EMC_REFRESH */
+					0x00000000 /* EMC_BURST_REFRESH_NUM */
+					0x00000030 /* EMC_PRE_REFRESH_REQ_CNT */
+					0x00000002 /* EMC_PDEX2WR */
+					0x00000002 /* EMC_PDEX2RD */
+					0x00000001 /* EMC_PCHG2PDEN */
+					0x00000000 /* EMC_ACT2PDEN */
+					0x00000007 /* EMC_AR2PDEN */
+					0x0000000f /* EMC_RW2PDEN */
+					0x00000007 /* EMC_TXSR */
+					0x00000007 /* EMC_TXSRDLL */
+					0x00000004 /* EMC_TCKE */
+					0x00000002 /* EMC_TFAW */
+					0x00000000 /* EMC_TRPAB */
+					0x00000004 /* EMC_TCLKSTABLE */
+					0x00000005 /* EMC_TCLKSTOP */
+					0x000000c7 /* EMC_TREFBW */
+					0x00000006 /* EMC_QUSE_EXTRA */
+					0x00000004 /* EMC_FBIO_CFG6 */
+					0x00000000 /* EMC_ODT_WRITE */
+					0x00000000 /* EMC_ODT_READ */
+					0x00004288 /* EMC_FBIO_CFG5 */
+					0x007800a4 /* EMC_CFG_DIG_DLL */
+					0x00008000 /* EMC_CFG_DIG_DLL_PERIOD */
+					0x000fc000 /* EMC_DLL_XFORM_DQS0 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS1 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS2 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS3 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS4 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS5 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS6 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS7 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE0 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE1 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE2 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE3 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE4 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE5 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE6 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE7 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS0 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS1 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS2 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS3 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS4 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS5 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS6 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS7 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ0 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ1 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ2 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ3 */
+					0x000002a0 /* EMC_XM2CMDPADCTRL */
+					0x0800211c /* EMC_XM2DQSPADCTRL2 */
+					0x00000000 /* EMC_XM2DQPADCTRL2 */
+					0x77fff884 /* EMC_XM2CLKPADCTRL */
+					0x01f1f108 /* EMC_XM2COMPPADCTRL */
+					0x05057404 /* EMC_XM2VTTGENPADCTRL */
+					0x54000007 /* EMC_XM2VTTGENPADCTRL2 */
+					0x08000168 /* EMC_XM2QUSEPADCTRL */
+					0x08000000 /* EMC_XM2DQSPADCTRL3 */
+					0x00000802 /* EMC_CTT_TERM_CTRL */
+					0x00000000 /* EMC_ZCAL_INTERVAL */
+					0x00000040 /* EMC_ZCAL_WAIT_CNT */
+					0x000c000c /* EMC_MRS_WAIT_CNT */
+					0xa0f10000 /* EMC_AUTO_CAL_CONFIG */
+					0x00000000 /* EMC_CTT */
+					0x00000000 /* EMC_CTT_DURATION */
+					0x80000287 /* EMC_DYN_SELF_REF_CONTROL */
+					0xe8000000 /* EMC_FBIO_SPARE */
+					0xff00ff00 /* EMC_CFG_RSV */
+				>;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200008>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-periodic-qrst;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-configuration = <
+					0x00000002 /* EMC_RC */
+					0x0000000d /* EMC_RFC */
+					0x00000001 /* EMC_RAS */
+					0x00000000 /* EMC_RP */
+					0x00000002 /* EMC_R2W */
+					0x0000000a /* EMC_W2R */
+					0x00000005 /* EMC_R2P */
+					0x0000000b /* EMC_W2P */
+					0x00000000 /* EMC_RD_RCD */
+					0x00000000 /* EMC_WR_RCD */
+					0x00000003 /* EMC_RRD */
+					0x00000001 /* EMC_REXT */
+					0x00000000 /* EMC_WEXT */
+					0x00000005 /* EMC_WDV */
+					0x00000005 /* EMC_QUSE */
+					0x00000004 /* EMC_QRST */
+					0x0000000a /* EMC_QSAFE */
+					0x0000000b /* EMC_RDV */
+					0x00000181 /* EMC_REFRESH */
+					0x00000000 /* EMC_BURST_REFRESH_NUM */
+					0x00000060 /* EMC_PRE_REFRESH_REQ_CNT */
+					0x00000002 /* EMC_PDEX2WR */
+					0x00000002 /* EMC_PDEX2RD */
+					0x00000001 /* EMC_PCHG2PDEN */
+					0x00000000 /* EMC_ACT2PDEN */
+					0x00000007 /* EMC_AR2PDEN */
+					0x0000000f /* EMC_RW2PDEN */
+					0x0000000e /* EMC_TXSR */
+					0x0000000e /* EMC_TXSRDLL */
+					0x00000004 /* EMC_TCKE */
+					0x00000003 /* EMC_TFAW */
+					0x00000000 /* EMC_TRPAB */
+					0x00000004 /* EMC_TCLKSTABLE */
+					0x00000005 /* EMC_TCLKSTOP */
+					0x0000018e /* EMC_TREFBW */
+					0x00000006 /* EMC_QUSE_EXTRA */
+					0x00000004 /* EMC_FBIO_CFG6 */
+					0x00000000 /* EMC_ODT_WRITE */
+					0x00000000 /* EMC_ODT_READ */
+					0x00004288 /* EMC_FBIO_CFG5 */
+					0x007800a4 /* EMC_CFG_DIG_DLL */
+					0x00008000 /* EMC_CFG_DIG_DLL_PERIOD */
+					0x000fc000 /* EMC_DLL_XFORM_DQS0 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS1 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS2 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS3 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS4 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS5 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS6 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS7 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE0 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE1 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE2 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE3 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE4 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE5 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE6 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE7 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS0 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS1 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS2 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS3 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS4 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS5 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS6 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS7 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ0 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ1 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ2 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ3 */
+					0x000002a0 /* EMC_XM2CMDPADCTRL */
+					0x0800211c /* EMC_XM2DQSPADCTRL2 */
+					0x00000000 /* EMC_XM2DQPADCTRL2 */
+					0x77fff884 /* EMC_XM2CLKPADCTRL */
+					0x01f1f108 /* EMC_XM2COMPPADCTRL */
+					0x05057404 /* EMC_XM2VTTGENPADCTRL */
+					0x54000007 /* EMC_XM2VTTGENPADCTRL2 */
+					0x08000168 /* EMC_XM2QUSEPADCTRL */
+					0x08000000 /* EMC_XM2DQSPADCTRL3 */
+					0x00000802 /* EMC_CTT_TERM_CTRL */
+					0x00000000 /* EMC_ZCAL_INTERVAL */
+					0x00000040 /* EMC_ZCAL_WAIT_CNT */
+					0x000c000c /* EMC_MRS_WAIT_CNT */
+					0xa0f10000 /* EMC_AUTO_CAL_CONFIG */
+					0x00000000 /* EMC_CTT */
+					0x00000000 /* EMC_CTT_DURATION */
+					0x8000040b /* EMC_DYN_SELF_REF_CONTROL */
+					0xe8000000 /* EMC_FBIO_SPARE */
+					0xff00ff00 /* EMC_CFG_RSV */
+				>;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200008>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-periodic-qrst;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-configuration = <
+					0x00000004 /* EMC_RC */
+					0x0000001a /* EMC_RFC */
+					0x00000003 /* EMC_RAS */
+					0x00000001 /* EMC_RP */
+					0x00000002 /* EMC_R2W */
+					0x0000000a /* EMC_W2R */
+					0x00000005 /* EMC_R2P */
+					0x0000000b /* EMC_W2P */
+					0x00000001 /* EMC_RD_RCD */
+					0x00000001 /* EMC_WR_RCD */
+					0x00000003 /* EMC_RRD */
+					0x00000001 /* EMC_REXT */
+					0x00000000 /* EMC_WEXT */
+					0x00000005 /* EMC_WDV */
+					0x00000005 /* EMC_QUSE */
+					0x00000004 /* EMC_QRST */
+					0x0000000a /* EMC_QSAFE */
+					0x0000000b /* EMC_RDV */
+					0x00000303 /* EMC_REFRESH */
+					0x00000000 /* EMC_BURST_REFRESH_NUM */
+					0x000000c0 /* EMC_PRE_REFRESH_REQ_CNT */
+					0x00000002 /* EMC_PDEX2WR */
+					0x00000002 /* EMC_PDEX2RD */
+					0x00000001 /* EMC_PCHG2PDEN */
+					0x00000000 /* EMC_ACT2PDEN */
+					0x00000007 /* EMC_AR2PDEN */
+					0x0000000f /* EMC_RW2PDEN */
+					0x0000001c /* EMC_TXSR */
+					0x0000001c /* EMC_TXSRDLL */
+					0x00000004 /* EMC_TCKE */
+					0x00000005 /* EMC_TFAW */
+					0x00000000 /* EMC_TRPAB */
+					0x00000004 /* EMC_TCLKSTABLE */
+					0x00000005 /* EMC_TCLKSTOP */
+					0x0000031c /* EMC_TREFBW */
+					0x00000006 /* EMC_QUSE_EXTRA */
+					0x00000004 /* EMC_FBIO_CFG6 */
+					0x00000000 /* EMC_ODT_WRITE */
+					0x00000000 /* EMC_ODT_READ */
+					0x00004288 /* EMC_FBIO_CFG5 */
+					0x007800a4 /* EMC_CFG_DIG_DLL */
+					0x00008000 /* EMC_CFG_DIG_DLL_PERIOD */
+					0x000fc000 /* EMC_DLL_XFORM_DQS0 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS1 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS2 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS3 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS4 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS5 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS6 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS7 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE0 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE1 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE2 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE3 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE4 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE5 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE6 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE7 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS0 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS1 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS2 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS3 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS4 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS5 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS6 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS7 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ0 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ1 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ2 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ3 */
+					0x000002a0 /* EMC_XM2CMDPADCTRL */
+					0x0800211c /* EMC_XM2DQSPADCTRL2 */
+					0x00000000 /* EMC_XM2DQPADCTRL2 */
+					0x77fff884 /* EMC_XM2CLKPADCTRL */
+					0x01f1f108 /* EMC_XM2COMPPADCTRL */
+					0x05057404 /* EMC_XM2VTTGENPADCTRL */
+					0x54000007 /* EMC_XM2VTTGENPADCTRL2 */
+					0x08000168 /* EMC_XM2QUSEPADCTRL */
+					0x08000000 /* EMC_XM2DQSPADCTRL3 */
+					0x00000802 /* EMC_CTT_TERM_CTRL */
+					0x00000000 /* EMC_ZCAL_INTERVAL */
+					0x00000040 /* EMC_ZCAL_WAIT_CNT */
+					0x000c000c /* EMC_MRS_WAIT_CNT */
+					0xa0f10000 /* EMC_AUTO_CAL_CONFIG */
+					0x00000000 /* EMC_CTT */
+					0x00000000 /* EMC_CTT_DURATION */
+					0x80000713 /* EMC_DYN_SELF_REF_CONTROL */
+					0xe8000000 /* EMC_FBIO_SPARE */
+					0xff00ff00 /* EMC_CFG_RSV */
+				>;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200008>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-periodic-qrst;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-configuration = <
+					0x00000009 /* EMC_RC */
+					0x00000035 /* EMC_RFC */
+					0x00000007 /* EMC_RAS */
+					0x00000002 /* EMC_RP */
+					0x00000002 /* EMC_R2W */
+					0x0000000a /* EMC_W2R */
+					0x00000005 /* EMC_R2P */
+					0x0000000b /* EMC_W2P */
+					0x00000002 /* EMC_RD_RCD */
+					0x00000002 /* EMC_WR_RCD */
+					0x00000003 /* EMC_RRD */
+					0x00000001 /* EMC_REXT */
+					0x00000000 /* EMC_WEXT */
+					0x00000005 /* EMC_WDV */
+					0x00000005 /* EMC_QUSE */
+					0x00000004 /* EMC_QRST */
+					0x0000000a /* EMC_QSAFE */
+					0x0000000b /* EMC_RDV */
+					0x00000607 /* EMC_REFRESH */
+					0x00000000 /* EMC_BURST_REFRESH_NUM */
+					0x00000181 /* EMC_PRE_REFRESH_REQ_CNT */
+					0x00000002 /* EMC_PDEX2WR */
+					0x00000002 /* EMC_PDEX2RD */
+					0x00000001 /* EMC_PCHG2PDEN */
+					0x00000000 /* EMC_ACT2PDEN */
+					0x00000007 /* EMC_AR2PDEN */
+					0x0000000f /* EMC_RW2PDEN */
+					0x00000038 /* EMC_TXSR */
+					0x00000038 /* EMC_TXSRDLL */
+					0x00000004 /* EMC_TCKE */
+					0x00000009 /* EMC_TFAW */
+					0x00000000 /* EMC_TRPAB */
+					0x00000004 /* EMC_TCLKSTABLE */
+					0x00000005 /* EMC_TCLKSTOP */
+					0x00000638 /* EMC_TREFBW */
+					0x00000006 /* EMC_QUSE_EXTRA */
+					0x00000006 /* EMC_FBIO_CFG6 */
+					0x00000000 /* EMC_ODT_WRITE */
+					0x00000000 /* EMC_ODT_READ */
+					0x00004288 /* EMC_FBIO_CFG5 */
+					0x004400a4 /* EMC_CFG_DIG_DLL */
+					0x00008000 /* EMC_CFG_DIG_DLL_PERIOD */
+					0x00080000 /* EMC_DLL_XFORM_DQS0 */
+					0x00080000 /* EMC_DLL_XFORM_DQS1 */
+					0x00080000 /* EMC_DLL_XFORM_DQS2 */
+					0x00080000 /* EMC_DLL_XFORM_DQS3 */
+					0x00080000 /* EMC_DLL_XFORM_DQS4 */
+					0x00080000 /* EMC_DLL_XFORM_DQS5 */
+					0x00080000 /* EMC_DLL_XFORM_DQS6 */
+					0x00080000 /* EMC_DLL_XFORM_DQS7 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE0 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE1 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE2 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE3 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE4 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE5 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE6 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE7 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS0 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS1 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS2 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS3 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS4 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS5 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS6 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS7 */
+					0x00080000 /* EMC_DLL_XFORM_DQ0 */
+					0x00080000 /* EMC_DLL_XFORM_DQ1 */
+					0x00080000 /* EMC_DLL_XFORM_DQ2 */
+					0x00080000 /* EMC_DLL_XFORM_DQ3 */
+					0x000002a0 /* EMC_XM2CMDPADCTRL */
+					0x0800211c /* EMC_XM2DQSPADCTRL2 */
+					0x00000000 /* EMC_XM2DQPADCTRL2 */
+					0x77fff884 /* EMC_XM2CLKPADCTRL */
+					0x01f1f108 /* EMC_XM2COMPPADCTRL */
+					0x05057404 /* EMC_XM2VTTGENPADCTRL */
+					0x54000007 /* EMC_XM2VTTGENPADCTRL2 */
+					0x08000168 /* EMC_XM2QUSEPADCTRL */
+					0x08000000 /* EMC_XM2DQSPADCTRL3 */
+					0x00000802 /* EMC_CTT_TERM_CTRL */
+					0x00020000 /* EMC_ZCAL_INTERVAL */
+					0x00000100 /* EMC_ZCAL_WAIT_CNT */
+					0x000c000c /* EMC_MRS_WAIT_CNT */
+					0xa0f10000 /* EMC_AUTO_CAL_CONFIG */
+					0x00000000 /* EMC_CTT */
+					0x00000000 /* EMC_CTT_DURATION */
+					0x80000d22 /* EMC_DYN_SELF_REF_CONTROL */
+					0xe8000000 /* EMC_FBIO_SPARE */
+					0xff00ff00 /* EMC_CFG_RSV */
+				>;
+			};
+
+			timing-400000000 {
+				clock-frequency = <400000000>;
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100002>;
+				nvidia,emc-mode-2 = <0x80200000>;
+				nvidia,emc-mode-reset = <0x80000521>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-configuration = <
+					0x00000012 /* EMC_RC */
+					0x00000066 /* EMC_RFC */
+					0x0000000c /* EMC_RAS */
+					0x00000004 /* EMC_RP */
+					0x00000003 /* EMC_R2W */
+					0x00000008 /* EMC_W2R */
+					0x00000002 /* EMC_R2P */
+					0x0000000a /* EMC_W2P */
+					0x00000004 /* EMC_RD_RCD */
+					0x00000004 /* EMC_WR_RCD */
+					0x00000002 /* EMC_RRD */
+					0x00000001 /* EMC_REXT */
+					0x00000000 /* EMC_WEXT */
+					0x00000004 /* EMC_WDV */
+					0x00000006 /* EMC_QUSE */
+					0x00000004 /* EMC_QRST */
+					0x0000000a /* EMC_QSAFE */
+					0x0000000c /* EMC_RDV */
+					0x00000bf0 /* EMC_REFRESH */
+					0x00000000 /* EMC_BURST_REFRESH_NUM */
+					0x000002fc /* EMC_PRE_REFRESH_REQ_CNT */
+					0x00000001 /* EMC_PDEX2WR */
+					0x00000008 /* EMC_PDEX2RD */
+					0x00000001 /* EMC_PCHG2PDEN */
+					0x00000000 /* EMC_ACT2PDEN */
+					0x00000008 /* EMC_AR2PDEN */
+					0x0000000f /* EMC_RW2PDEN */
+					0x0000006c /* EMC_TXSR */
+					0x00000200 /* EMC_TXSRDLL */
+					0x00000004 /* EMC_TCKE */
+					0x00000010 /* EMC_TFAW */
+					0x00000000 /* EMC_TRPAB */
+					0x00000004 /* EMC_TCLKSTABLE */
+					0x00000005 /* EMC_TCLKSTOP */
+					0x00000c30 /* EMC_TREFBW */
+					0x00000000 /* EMC_QUSE_EXTRA */
+					0x00000004 /* EMC_FBIO_CFG6 */
+					0x00000000 /* EMC_ODT_WRITE */
+					0x00000000 /* EMC_ODT_READ */
+					0x00007088 /* EMC_FBIO_CFG5 */
+					0x001d0084 /* EMC_CFG_DIG_DLL */
+					0x00008000 /* EMC_CFG_DIG_DLL_PERIOD */
+					0x0003c000 /* EMC_DLL_XFORM_DQS0 */
+					0x0003c000 /* EMC_DLL_XFORM_DQS1 */
+					0x0003c000 /* EMC_DLL_XFORM_DQS2 */
+					0x0003c000 /* EMC_DLL_XFORM_DQS3 */
+					0x0003c000 /* EMC_DLL_XFORM_DQS4 */
+					0x0003c000 /* EMC_DLL_XFORM_DQS5 */
+					0x0003c000 /* EMC_DLL_XFORM_DQS6 */
+					0x0003c000 /* EMC_DLL_XFORM_DQS7 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE0 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE1 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE2 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE3 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE4 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE5 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE6 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE7 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS0 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS1 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS2 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS3 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS4 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS5 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS6 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS7 */
+					0x00048000 /* EMC_DLL_XFORM_DQ0 */
+					0x00048000 /* EMC_DLL_XFORM_DQ1 */
+					0x00048000 /* EMC_DLL_XFORM_DQ2 */
+					0x00048000 /* EMC_DLL_XFORM_DQ3 */
+					0x000002a0 /* EMC_XM2CMDPADCTRL */
+					0x0800013d /* EMC_XM2DQSPADCTRL2 */
+					0x00000000 /* EMC_XM2DQPADCTRL2 */
+					0x77fff884 /* EMC_XM2CLKPADCTRL */
+					0x01f1f508 /* EMC_XM2COMPPADCTRL */
+					0x05057404 /* EMC_XM2VTTGENPADCTRL */
+					0x54000007 /* EMC_XM2VTTGENPADCTRL2 */
+					0x080001e8 /* EMC_XM2QUSEPADCTRL */
+					0x08000021 /* EMC_XM2DQSPADCTRL3 */
+					0x00000802 /* EMC_CTT_TERM_CTRL */
+					0x00020000 /* EMC_ZCAL_INTERVAL */
+					0x00000100 /* EMC_ZCAL_WAIT_CNT */
+					0x0158000c /* EMC_MRS_WAIT_CNT */
+					0xa0f10000 /* EMC_AUTO_CAL_CONFIG */
+					0x00000000 /* EMC_CTT */
+					0x00000000 /* EMC_CTT_DURATION */
+					0x800018c8 /* EMC_DYN_SELF_REF_CONTROL */
+					0xe8000000 /* EMC_FBIO_SPARE */
+					0xff00ff89 /* EMC_CFG_RSV */
+				>;
+			};
+
+			timing-800000000 {
+				clock-frequency = <800000000>;
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100002>;
+				nvidia,emc-mode-2 = <0x80200018>;
+				nvidia,emc-mode-reset = <0x80000d71>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-periodic-qrst;
+				nvidia,emc-configuration = <
+					0x00000025 /* EMC_RC */
+					0x000000ce /* EMC_RFC */
+					0x0000001a /* EMC_RAS */
+					0x00000009 /* EMC_RP */
+					0x00000005 /* EMC_R2W */
+					0x0000000d /* EMC_W2R */
+					0x00000004 /* EMC_R2P */
+					0x00000013 /* EMC_W2P */
+					0x00000009 /* EMC_RD_RCD */
+					0x00000009 /* EMC_WR_RCD */
+					0x00000004 /* EMC_RRD */
+					0x00000001 /* EMC_REXT */
+					0x00000000 /* EMC_WEXT */
+					0x00000007 /* EMC_WDV */
+					0x0000000a /* EMC_QUSE */
+					0x00000009 /* EMC_QRST */
+					0x0000000b /* EMC_QSAFE */
+					0x00000011 /* EMC_RDV */
+					0x00001820 /* EMC_REFRESH */
+					0x00000000 /* EMC_BURST_REFRESH_NUM */
+					0x00000608 /* EMC_PRE_REFRESH_REQ_CNT */
+					0x00000003 /* EMC_PDEX2WR */
+					0x00000012 /* EMC_PDEX2RD */
+					0x00000001 /* EMC_PCHG2PDEN */
+					0x00000000 /* EMC_ACT2PDEN */
+					0x0000000f /* EMC_AR2PDEN */
+					0x00000018 /* EMC_RW2PDEN */
+					0x000000d8 /* EMC_TXSR */
+					0x00000200 /* EMC_TXSRDLL */
+					0x00000005 /* EMC_TCKE */
+					0x00000020 /* EMC_TFAW */
+					0x00000000 /* EMC_TRPAB */
+					0x00000007 /* EMC_TCLKSTABLE */
+					0x00000008 /* EMC_TCLKSTOP */
+					0x00001860 /* EMC_TREFBW */
+					0x0000000b /* EMC_QUSE_EXTRA */
+					0x00000006 /* EMC_FBIO_CFG6 */
+					0x00000000 /* EMC_ODT_WRITE */
+					0x00000000 /* EMC_ODT_READ */
+					0x00005088 /* EMC_FBIO_CFG5 */
+					0xf0070191 /* EMC_CFG_DIG_DLL */
+					0x00008000 /* EMC_CFG_DIG_DLL_PERIOD */
+					0x0000800a /* EMC_DLL_XFORM_DQS0 */
+					0x0000000a /* EMC_DLL_XFORM_DQS1 */
+					0x0000000a /* EMC_DLL_XFORM_DQS2 */
+					0x0000000a /* EMC_DLL_XFORM_DQS3 */
+					0x0000000a /* EMC_DLL_XFORM_DQS4 */
+					0x0000000a /* EMC_DLL_XFORM_DQS5 */
+					0x0000000a /* EMC_DLL_XFORM_DQS6 */
+					0x0000000a /* EMC_DLL_XFORM_DQS7 */
+					0x00018000 /* EMC_DLL_XFORM_QUSE0 */
+					0x00018000 /* EMC_DLL_XFORM_QUSE1 */
+					0x00018000 /* EMC_DLL_XFORM_QUSE2 */
+					0x00018000 /* EMC_DLL_XFORM_QUSE3 */
+					0x00018000 /* EMC_DLL_XFORM_QUSE4 */
+					0x00018000 /* EMC_DLL_XFORM_QUSE5 */
+					0x00018000 /* EMC_DLL_XFORM_QUSE6 */
+					0x00018000 /* EMC_DLL_XFORM_QUSE7 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS0 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS1 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS2 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS3 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS4 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS5 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS6 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS7 */
+					0x0000000a /* EMC_DLL_XFORM_DQ0 */
+					0x0000000a /* EMC_DLL_XFORM_DQ1 */
+					0x0000000a /* EMC_DLL_XFORM_DQ2 */
+					0x0000000a /* EMC_DLL_XFORM_DQ3 */
+					0x000002a0 /* EMC_XM2CMDPADCTRL */
+					0x0600013d /* EMC_XM2DQSPADCTRL2 */
+					0x22220000 /* EMC_XM2DQPADCTRL2 */
+					0x77fff884 /* EMC_XM2CLKPADCTRL */
+					0x01f1f501 /* EMC_XM2COMPPADCTRL */
+					0x07077404 /* EMC_XM2VTTGENPADCTRL */
+					0x54000000 /* EMC_XM2VTTGENPADCTRL2 */
+					0x080001e8 /* EMC_XM2QUSEPADCTRL */
+					0x08000021 /* EMC_XM2DQSPADCTRL3 */
+					0x00000802 /* EMC_CTT_TERM_CTRL */
+					0x00020000 /* EMC_ZCAL_INTERVAL */
+					0x00000100 /* EMC_ZCAL_WAIT_CNT */
+					0x00f0000c /* EMC_MRS_WAIT_CNT */
+					0xa0f10000 /* EMC_AUTO_CAL_CONFIG */
+					0x00000000 /* EMC_CTT */
+					0x00000000 /* EMC_CTT_DURATION */
+					0x8000308c /* EMC_DYN_SELF_REF_CONTROL */
+					0xe8000000 /* EMC_FBIO_SPARE */
+					0xff00ff49 /* EMC_CFG_RSV */
+				>;
+			};
+		};
+
+		emc-timings-1 {
+			nvidia,ram-code = <1>;  /* Hynix M RAM */
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200008>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-periodic-qrst;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-configuration = <
+					0x00000001 /* EMC_RC */
+					0x00000006 /* EMC_RFC */
+					0x00000000 /* EMC_RAS */
+					0x00000000 /* EMC_RP */
+					0x00000002 /* EMC_R2W */
+					0x0000000a /* EMC_W2R */
+					0x00000005 /* EMC_R2P */
+					0x0000000b /* EMC_W2P */
+					0x00000000 /* EMC_RD_RCD */
+					0x00000000 /* EMC_WR_RCD */
+					0x00000003 /* EMC_RRD */
+					0x00000001 /* EMC_REXT */
+					0x00000000 /* EMC_WEXT */
+					0x00000005 /* EMC_WDV */
+					0x00000005 /* EMC_QUSE */
+					0x00000004 /* EMC_QRST */
+					0x0000000a /* EMC_QSAFE */
+					0x0000000b /* EMC_RDV */
+					0x000000c0 /* EMC_REFRESH */
+					0x00000000 /* EMC_BURST_REFRESH_NUM */
+					0x00000030 /* EMC_PRE_REFRESH_REQ_CNT */
+					0x00000002 /* EMC_PDEX2WR */
+					0x00000002 /* EMC_PDEX2RD */
+					0x00000001 /* EMC_PCHG2PDEN */
+					0x00000000 /* EMC_ACT2PDEN */
+					0x00000007 /* EMC_AR2PDEN */
+					0x0000000f /* EMC_RW2PDEN */
+					0x00000007 /* EMC_TXSR */
+					0x00000007 /* EMC_TXSRDLL */
+					0x00000004 /* EMC_TCKE */
+					0x00000002 /* EMC_TFAW */
+					0x00000000 /* EMC_TRPAB */
+					0x00000004 /* EMC_TCLKSTABLE */
+					0x00000005 /* EMC_TCLKSTOP */
+					0x000000c7 /* EMC_TREFBW */
+					0x00000006 /* EMC_QUSE_EXTRA */
+					0x00000004 /* EMC_FBIO_CFG6 */
+					0x00000000 /* EMC_ODT_WRITE */
+					0x00000000 /* EMC_ODT_READ */
+					0x00004288 /* EMC_FBIO_CFG5 */
+					0x007800a4 /* EMC_CFG_DIG_DLL */
+					0x00008000 /* EMC_CFG_DIG_DLL_PERIOD */
+					0x000fc000 /* EMC_DLL_XFORM_DQS0 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS1 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS2 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS3 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS4 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS5 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS6 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS7 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE0 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE1 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE2 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE3 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE4 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE5 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE6 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE7 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS0 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS1 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS2 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS3 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS4 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS5 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS6 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS7 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ0 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ1 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ2 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ3 */
+					0x000002a0 /* EMC_XM2CMDPADCTRL */
+					0x0800211c /* EMC_XM2DQSPADCTRL2 */
+					0x00000000 /* EMC_XM2DQPADCTRL2 */
+					0x77fff884 /* EMC_XM2CLKPADCTRL */
+					0x01f1f108 /* EMC_XM2COMPPADCTRL */
+					0x05057404 /* EMC_XM2VTTGENPADCTRL */
+					0x54000007 /* EMC_XM2VTTGENPADCTRL2 */
+					0x08000168 /* EMC_XM2QUSEPADCTRL */
+					0x08000000 /* EMC_XM2DQSPADCTRL3 */
+					0x00000802 /* EMC_CTT_TERM_CTRL */
+					0x00000000 /* EMC_ZCAL_INTERVAL */
+					0x00000040 /* EMC_ZCAL_WAIT_CNT */
+					0x000c000c /* EMC_MRS_WAIT_CNT */
+					0xa0f10000 /* EMC_AUTO_CAL_CONFIG */
+					0x00000000 /* EMC_CTT */
+					0x00000000 /* EMC_CTT_DURATION */
+					0x80000287 /* EMC_DYN_SELF_REF_CONTROL */
+					0xe8000000 /* EMC_FBIO_SPARE */
+					0xff00ff00 /* EMC_CFG_RSV */
+				>;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200008>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-periodic-qrst;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-configuration = <
+					0x00000002 /* EMC_RC */
+					0x0000000d /* EMC_RFC */
+					0x00000001 /* EMC_RAS */
+					0x00000000 /* EMC_RP */
+					0x00000002 /* EMC_R2W */
+					0x0000000a /* EMC_W2R */
+					0x00000005 /* EMC_R2P */
+					0x0000000b /* EMC_W2P */
+					0x00000000 /* EMC_RD_RCD */
+					0x00000000 /* EMC_WR_RCD */
+					0x00000003 /* EMC_RRD */
+					0x00000001 /* EMC_REXT */
+					0x00000000 /* EMC_WEXT */
+					0x00000005 /* EMC_WDV */
+					0x00000005 /* EMC_QUSE */
+					0x00000004 /* EMC_QRST */
+					0x0000000a /* EMC_QSAFE */
+					0x0000000b /* EMC_RDV */
+					0x00000181 /* EMC_REFRESH */
+					0x00000000 /* EMC_BURST_REFRESH_NUM */
+					0x00000060 /* EMC_PRE_REFRESH_REQ_CNT */
+					0x00000002 /* EMC_PDEX2WR */
+					0x00000002 /* EMC_PDEX2RD */
+					0x00000001 /* EMC_PCHG2PDEN */
+					0x00000000 /* EMC_ACT2PDEN */
+					0x00000007 /* EMC_AR2PDEN */
+					0x0000000f /* EMC_RW2PDEN */
+					0x0000000e /* EMC_TXSR */
+					0x0000000e /* EMC_TXSRDLL */
+					0x00000004 /* EMC_TCKE */
+					0x00000003 /* EMC_TFAW */
+					0x00000000 /* EMC_TRPAB */
+					0x00000004 /* EMC_TCLKSTABLE */
+					0x00000005 /* EMC_TCLKSTOP */
+					0x0000018e /* EMC_TREFBW */
+					0x00000006 /* EMC_QUSE_EXTRA */
+					0x00000004 /* EMC_FBIO_CFG6 */
+					0x00000000 /* EMC_ODT_WRITE */
+					0x00000000 /* EMC_ODT_READ */
+					0x00004288 /* EMC_FBIO_CFG5 */
+					0x007800a4 /* EMC_CFG_DIG_DLL */
+					0x00008000 /* EMC_CFG_DIG_DLL_PERIOD */
+					0x000fc000 /* EMC_DLL_XFORM_DQS0 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS1 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS2 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS3 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS4 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS5 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS6 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS7 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE0 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE1 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE2 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE3 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE4 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE5 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE6 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE7 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS0 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS1 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS2 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS3 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS4 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS5 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS6 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS7 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ0 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ1 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ2 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ3 */
+					0x000002a0 /* EMC_XM2CMDPADCTRL */
+					0x0800211c /* EMC_XM2DQSPADCTRL2 */
+					0x00000000 /* EMC_XM2DQPADCTRL2 */
+					0x77fff884 /* EMC_XM2CLKPADCTRL */
+					0x01f1f108 /* EMC_XM2COMPPADCTRL */
+					0x05057404 /* EMC_XM2VTTGENPADCTRL */
+					0x54000007 /* EMC_XM2VTTGENPADCTRL2 */
+					0x08000168 /* EMC_XM2QUSEPADCTRL */
+					0x08000000 /* EMC_XM2DQSPADCTRL3 */
+					0x00000802 /* EMC_CTT_TERM_CTRL */
+					0x00000000 /* EMC_ZCAL_INTERVAL */
+					0x00000040 /* EMC_ZCAL_WAIT_CNT */
+					0x000c000c /* EMC_MRS_WAIT_CNT */
+					0xa0f10000 /* EMC_AUTO_CAL_CONFIG */
+					0x00000000 /* EMC_CTT */
+					0x00000000 /* EMC_CTT_DURATION */
+					0x8000040b /* EMC_DYN_SELF_REF_CONTROL */
+					0xe8000000 /* EMC_FBIO_SPARE */
+					0xff00ff00 /* EMC_CFG_RSV */
+				>;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200008>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-periodic-qrst;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-configuration = <
+					0x00000004 /* EMC_RC */
+					0x0000001a /* EMC_RFC */
+					0x00000003 /* EMC_RAS */
+					0x00000001 /* EMC_RP */
+					0x00000002 /* EMC_R2W */
+					0x0000000a /* EMC_W2R */
+					0x00000005 /* EMC_R2P */
+					0x0000000b /* EMC_W2P */
+					0x00000001 /* EMC_RD_RCD */
+					0x00000001 /* EMC_WR_RCD */
+					0x00000003 /* EMC_RRD */
+					0x00000001 /* EMC_REXT */
+					0x00000000 /* EMC_WEXT */
+					0x00000005 /* EMC_WDV */
+					0x00000005 /* EMC_QUSE */
+					0x00000004 /* EMC_QRST */
+					0x0000000a /* EMC_QSAFE */
+					0x0000000b /* EMC_RDV */
+					0x00000303 /* EMC_REFRESH */
+					0x00000000 /* EMC_BURST_REFRESH_NUM */
+					0x000000c0 /* EMC_PRE_REFRESH_REQ_CNT */
+					0x00000002 /* EMC_PDEX2WR */
+					0x00000002 /* EMC_PDEX2RD */
+					0x00000001 /* EMC_PCHG2PDEN */
+					0x00000000 /* EMC_ACT2PDEN */
+					0x00000007 /* EMC_AR2PDEN */
+					0x0000000f /* EMC_RW2PDEN */
+					0x0000001c /* EMC_TXSR */
+					0x0000001c /* EMC_TXSRDLL */
+					0x00000004 /* EMC_TCKE */
+					0x00000005 /* EMC_TFAW */
+					0x00000000 /* EMC_TRPAB */
+					0x00000004 /* EMC_TCLKSTABLE */
+					0x00000005 /* EMC_TCLKSTOP */
+					0x0000031c /* EMC_TREFBW */
+					0x00000006 /* EMC_QUSE_EXTRA */
+					0x00000004 /* EMC_FBIO_CFG6 */
+					0x00000000 /* EMC_ODT_WRITE */
+					0x00000000 /* EMC_ODT_READ */
+					0x00004288 /* EMC_FBIO_CFG5 */
+					0x007800a4 /* EMC_CFG_DIG_DLL */
+					0x00008000 /* EMC_CFG_DIG_DLL_PERIOD */
+					0x000fc000 /* EMC_DLL_XFORM_DQS0 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS1 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS2 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS3 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS4 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS5 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS6 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS7 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE0 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE1 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE2 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE3 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE4 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE5 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE6 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE7 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS0 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS1 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS2 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS3 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS4 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS5 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS6 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS7 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ0 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ1 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ2 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ3 */
+					0x000002a0 /* EMC_XM2CMDPADCTRL */
+					0x0800211c /* EMC_XM2DQSPADCTRL2 */
+					0x00000000 /* EMC_XM2DQPADCTRL2 */
+					0x77fff884 /* EMC_XM2CLKPADCTRL */
+					0x01f1f108 /* EMC_XM2COMPPADCTRL */
+					0x05057404 /* EMC_XM2VTTGENPADCTRL */
+					0x54000007 /* EMC_XM2VTTGENPADCTRL2 */
+					0x08000168 /* EMC_XM2QUSEPADCTRL */
+					0x08000000 /* EMC_XM2DQSPADCTRL3 */
+					0x00000802 /* EMC_CTT_TERM_CTRL */
+					0x00000000 /* EMC_ZCAL_INTERVAL */
+					0x00000040 /* EMC_ZCAL_WAIT_CNT */
+					0x000c000c /* EMC_MRS_WAIT_CNT */
+					0xa0f10000 /* EMC_AUTO_CAL_CONFIG */
+					0x00000000 /* EMC_CTT */
+					0x00000000 /* EMC_CTT_DURATION */
+					0x80000713 /* EMC_DYN_SELF_REF_CONTROL */
+					0xe8000000 /* EMC_FBIO_SPARE */
+					0xff00ff00 /* EMC_CFG_RSV */
+				>;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200008>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-periodic-qrst;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-configuration = <
+					0x00000009 /* EMC_RC */
+					0x00000035 /* EMC_RFC */
+					0x00000007 /* EMC_RAS */
+					0x00000002 /* EMC_RP */
+					0x00000002 /* EMC_R2W */
+					0x0000000a /* EMC_W2R */
+					0x00000005 /* EMC_R2P */
+					0x0000000b /* EMC_W2P */
+					0x00000002 /* EMC_RD_RCD */
+					0x00000002 /* EMC_WR_RCD */
+					0x00000003 /* EMC_RRD */
+					0x00000001 /* EMC_REXT */
+					0x00000000 /* EMC_WEXT */
+					0x00000005 /* EMC_WDV */
+					0x00000005 /* EMC_QUSE */
+					0x00000004 /* EMC_QRST */
+					0x0000000a /* EMC_QSAFE */
+					0x0000000b /* EMC_RDV */
+					0x00000607 /* EMC_REFRESH */
+					0x00000000 /* EMC_BURST_REFRESH_NUM */
+					0x00000181 /* EMC_PRE_REFRESH_REQ_CNT */
+					0x00000002 /* EMC_PDEX2WR */
+					0x00000002 /* EMC_PDEX2RD */
+					0x00000001 /* EMC_PCHG2PDEN */
+					0x00000000 /* EMC_ACT2PDEN */
+					0x00000007 /* EMC_AR2PDEN */
+					0x0000000f /* EMC_RW2PDEN */
+					0x00000038 /* EMC_TXSR */
+					0x00000038 /* EMC_TXSRDLL */
+					0x00000004 /* EMC_TCKE */
+					0x00000009 /* EMC_TFAW */
+					0x00000000 /* EMC_TRPAB */
+					0x00000004 /* EMC_TCLKSTABLE */
+					0x00000005 /* EMC_TCLKSTOP */
+					0x00000638 /* EMC_TREFBW */
+					0x00000006 /* EMC_QUSE_EXTRA */
+					0x00000006 /* EMC_FBIO_CFG6 */
+					0x00000000 /* EMC_ODT_WRITE */
+					0x00000000 /* EMC_ODT_READ */
+					0x00004288 /* EMC_FBIO_CFG5 */
+					0x004400a4 /* EMC_CFG_DIG_DLL */
+					0x00008000 /* EMC_CFG_DIG_DLL_PERIOD */
+					0x00080000 /* EMC_DLL_XFORM_DQS0 */
+					0x00080000 /* EMC_DLL_XFORM_DQS1 */
+					0x00080000 /* EMC_DLL_XFORM_DQS2 */
+					0x00080000 /* EMC_DLL_XFORM_DQS3 */
+					0x00080000 /* EMC_DLL_XFORM_DQS4 */
+					0x00080000 /* EMC_DLL_XFORM_DQS5 */
+					0x00080000 /* EMC_DLL_XFORM_DQS6 */
+					0x00080000 /* EMC_DLL_XFORM_DQS7 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE0 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE1 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE2 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE3 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE4 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE5 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE6 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE7 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS0 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS1 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS2 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS3 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS4 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS5 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS6 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS7 */
+					0x00080000 /* EMC_DLL_XFORM_DQ0 */
+					0x00080000 /* EMC_DLL_XFORM_DQ1 */
+					0x00080000 /* EMC_DLL_XFORM_DQ2 */
+					0x00080000 /* EMC_DLL_XFORM_DQ3 */
+					0x000002a0 /* EMC_XM2CMDPADCTRL */
+					0x0800211c /* EMC_XM2DQSPADCTRL2 */
+					0x00000000 /* EMC_XM2DQPADCTRL2 */
+					0x77fff884 /* EMC_XM2CLKPADCTRL */
+					0x01f1f108 /* EMC_XM2COMPPADCTRL */
+					0x05057404 /* EMC_XM2VTTGENPADCTRL */
+					0x54000007 /* EMC_XM2VTTGENPADCTRL2 */
+					0x08000168 /* EMC_XM2QUSEPADCTRL */
+					0x08000000 /* EMC_XM2DQSPADCTRL3 */
+					0x00000802 /* EMC_CTT_TERM_CTRL */
+					0x00020000 /* EMC_ZCAL_INTERVAL */
+					0x00000100 /* EMC_ZCAL_WAIT_CNT */
+					0x000c000c /* EMC_MRS_WAIT_CNT */
+					0xa0f10000 /* EMC_AUTO_CAL_CONFIG */
+					0x00000000 /* EMC_CTT */
+					0x00000000 /* EMC_CTT_DURATION */
+					0x80000d22 /* EMC_DYN_SELF_REF_CONTROL */
+					0xe8000000 /* EMC_FBIO_SPARE */
+					0xff00ff00 /* EMC_CFG_RSV */
+				>;
+			};
+
+			timing-400000000 {
+				clock-frequency = <400000000>;
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100002>;
+				nvidia,emc-mode-2 = <0x80200000>;
+				nvidia,emc-mode-reset = <0x80000521>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-configuration = <
+					0x00000012 /* EMC_RC */
+					0x00000066 /* EMC_RFC */
+					0x0000000c /* EMC_RAS */
+					0x00000004 /* EMC_RP */
+					0x00000003 /* EMC_R2W */
+					0x00000008 /* EMC_W2R */
+					0x00000002 /* EMC_R2P */
+					0x0000000a /* EMC_W2P */
+					0x00000004 /* EMC_RD_RCD */
+					0x00000004 /* EMC_WR_RCD */
+					0x00000002 /* EMC_RRD */
+					0x00000001 /* EMC_REXT */
+					0x00000000 /* EMC_WEXT */
+					0x00000004 /* EMC_WDV */
+					0x00000006 /* EMC_QUSE */
+					0x00000004 /* EMC_QRST */
+					0x0000000a /* EMC_QSAFE */
+					0x0000000c /* EMC_RDV */
+					0x00000bf0 /* EMC_REFRESH */
+					0x00000000 /* EMC_BURST_REFRESH_NUM */
+					0x000002fc /* EMC_PRE_REFRESH_REQ_CNT */
+					0x00000001 /* EMC_PDEX2WR */
+					0x00000008 /* EMC_PDEX2RD */
+					0x00000001 /* EMC_PCHG2PDEN */
+					0x00000000 /* EMC_ACT2PDEN */
+					0x00000008 /* EMC_AR2PDEN */
+					0x0000000f /* EMC_RW2PDEN */
+					0x0000006c /* EMC_TXSR */
+					0x00000200 /* EMC_TXSRDLL */
+					0x00000004 /* EMC_TCKE */
+					0x00000010 /* EMC_TFAW */
+					0x00000000 /* EMC_TRPAB */
+					0x00000004 /* EMC_TCLKSTABLE */
+					0x00000005 /* EMC_TCLKSTOP */
+					0x00000c30 /* EMC_TREFBW */
+					0x00000000 /* EMC_QUSE_EXTRA */
+					0x00000004 /* EMC_FBIO_CFG6 */
+					0x00000000 /* EMC_ODT_WRITE */
+					0x00000000 /* EMC_ODT_READ */
+					0x00007088 /* EMC_FBIO_CFG5 */
+					0x001d0084 /* EMC_CFG_DIG_DLL */
+					0x00008000 /* EMC_CFG_DIG_DLL_PERIOD */
+					0x0003c000 /* EMC_DLL_XFORM_DQS0 */
+					0x0003c000 /* EMC_DLL_XFORM_DQS1 */
+					0x0003c000 /* EMC_DLL_XFORM_DQS2 */
+					0x0003c000 /* EMC_DLL_XFORM_DQS3 */
+					0x0003c000 /* EMC_DLL_XFORM_DQS4 */
+					0x0003c000 /* EMC_DLL_XFORM_DQS5 */
+					0x0003c000 /* EMC_DLL_XFORM_DQS6 */
+					0x0003c000 /* EMC_DLL_XFORM_DQS7 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE0 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE1 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE2 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE3 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE4 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE5 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE6 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE7 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS0 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS1 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS2 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS3 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS4 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS5 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS6 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS7 */
+					0x00048000 /* EMC_DLL_XFORM_DQ0 */
+					0x00048000 /* EMC_DLL_XFORM_DQ1 */
+					0x00048000 /* EMC_DLL_XFORM_DQ2 */
+					0x00048000 /* EMC_DLL_XFORM_DQ3 */
+					0x000002a0 /* EMC_XM2CMDPADCTRL */
+					0x0800013d /* EMC_XM2DQSPADCTRL2 */
+					0x00000000 /* EMC_XM2DQPADCTRL2 */
+					0x77fff884 /* EMC_XM2CLKPADCTRL */
+					0x01f1f508 /* EMC_XM2COMPPADCTRL */
+					0x05057404 /* EMC_XM2VTTGENPADCTRL */
+					0x54000007 /* EMC_XM2VTTGENPADCTRL2 */
+					0x080001e8 /* EMC_XM2QUSEPADCTRL */
+					0x08000021 /* EMC_XM2DQSPADCTRL3 */
+					0x00000802 /* EMC_CTT_TERM_CTRL */
+					0x00020000 /* EMC_ZCAL_INTERVAL */
+					0x00000100 /* EMC_ZCAL_WAIT_CNT */
+					0x0158000c /* EMC_MRS_WAIT_CNT */
+					0xa0f10000 /* EMC_AUTO_CAL_CONFIG */
+					0x00000000 /* EMC_CTT */
+					0x00000000 /* EMC_CTT_DURATION */
+					0x800018c8 /* EMC_DYN_SELF_REF_CONTROL */
+					0xe8000000 /* EMC_FBIO_SPARE */
+					0xff00ff89 /* EMC_CFG_RSV */
+				>;
+			};
+
+			timing-800000000 {
+				clock-frequency = <800000000>;
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100002>;
+				nvidia,emc-mode-2 = <0x80200018>;
+				nvidia,emc-mode-reset = <0x80000d71>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-periodic-qrst;
+				nvidia,emc-configuration = <
+					0x00000025 /* EMC_RC */
+					0x000000ce /* EMC_RFC */
+					0x0000001a /* EMC_RAS */
+					0x00000009 /* EMC_RP */
+					0x00000005 /* EMC_R2W */
+					0x0000000d /* EMC_W2R */
+					0x00000004 /* EMC_R2P */
+					0x00000013 /* EMC_W2P */
+					0x00000009 /* EMC_RD_RCD */
+					0x00000009 /* EMC_WR_RCD */
+					0x00000004 /* EMC_RRD */
+					0x00000001 /* EMC_REXT */
+					0x00000000 /* EMC_WEXT */
+					0x00000007 /* EMC_WDV */
+					0x0000000a /* EMC_QUSE */
+					0x00000009 /* EMC_QRST */
+					0x0000000b /* EMC_QSAFE */
+					0x00000011 /* EMC_RDV */
+					0x00001820 /* EMC_REFRESH */
+					0x00000000 /* EMC_BURST_REFRESH_NUM */
+					0x00000608 /* EMC_PRE_REFRESH_REQ_CNT */
+					0x00000003 /* EMC_PDEX2WR */
+					0x00000012 /* EMC_PDEX2RD */
+					0x00000001 /* EMC_PCHG2PDEN */
+					0x00000000 /* EMC_ACT2PDEN */
+					0x0000000f /* EMC_AR2PDEN */
+					0x00000018 /* EMC_RW2PDEN */
+					0x000000d8 /* EMC_TXSR */
+					0x00000200 /* EMC_TXSRDLL */
+					0x00000005 /* EMC_TCKE */
+					0x00000020 /* EMC_TFAW */
+					0x00000000 /* EMC_TRPAB */
+					0x00000007 /* EMC_TCLKSTABLE */
+					0x00000008 /* EMC_TCLKSTOP */
+					0x00001860 /* EMC_TREFBW */
+					0x0000000b /* EMC_QUSE_EXTRA */
+					0x00000006 /* EMC_FBIO_CFG6 */
+					0x00000000 /* EMC_ODT_WRITE */
+					0x00000000 /* EMC_ODT_READ */
+					0x00005088 /* EMC_FBIO_CFG5 */
+					0xf0070191 /* EMC_CFG_DIG_DLL */
+					0x00008000 /* EMC_CFG_DIG_DLL_PERIOD */
+					0x0000800a /* EMC_DLL_XFORM_DQS0 */
+					0x0000000a /* EMC_DLL_XFORM_DQS1 */
+					0x0000000a /* EMC_DLL_XFORM_DQS2 */
+					0x0000000a /* EMC_DLL_XFORM_DQS3 */
+					0x0000000a /* EMC_DLL_XFORM_DQS4 */
+					0x0000000a /* EMC_DLL_XFORM_DQS5 */
+					0x0000000a /* EMC_DLL_XFORM_DQS6 */
+					0x0000000a /* EMC_DLL_XFORM_DQS7 */
+					0x00018000 /* EMC_DLL_XFORM_QUSE0 */
+					0x00018000 /* EMC_DLL_XFORM_QUSE1 */
+					0x00018000 /* EMC_DLL_XFORM_QUSE2 */
+					0x00018000 /* EMC_DLL_XFORM_QUSE3 */
+					0x00018000 /* EMC_DLL_XFORM_QUSE4 */
+					0x00018000 /* EMC_DLL_XFORM_QUSE5 */
+					0x00018000 /* EMC_DLL_XFORM_QUSE6 */
+					0x00018000 /* EMC_DLL_XFORM_QUSE7 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS0 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS1 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS2 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS3 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS4 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS5 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS6 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS7 */
+					0x0000000a /* EMC_DLL_XFORM_DQ0 */
+					0x0000000a /* EMC_DLL_XFORM_DQ1 */
+					0x0000000a /* EMC_DLL_XFORM_DQ2 */
+					0x0000000a /* EMC_DLL_XFORM_DQ3 */
+					0x000002a0 /* EMC_XM2CMDPADCTRL */
+					0x0600013d /* EMC_XM2DQSPADCTRL2 */
+					0x22220000 /* EMC_XM2DQPADCTRL2 */
+					0x77fff884 /* EMC_XM2CLKPADCTRL */
+					0x01f1f501 /* EMC_XM2COMPPADCTRL */
+					0x07077404 /* EMC_XM2VTTGENPADCTRL */
+					0x54000000 /* EMC_XM2VTTGENPADCTRL2 */
+					0x080001e8 /* EMC_XM2QUSEPADCTRL */
+					0x08000021 /* EMC_XM2DQSPADCTRL3 */
+					0x00000802 /* EMC_CTT_TERM_CTRL */
+					0x00020000 /* EMC_ZCAL_INTERVAL */
+					0x00000100 /* EMC_ZCAL_WAIT_CNT */
+					0x00f0000c /* EMC_MRS_WAIT_CNT */
+					0xa0f10000 /* EMC_AUTO_CAL_CONFIG */
+					0x00000000 /* EMC_CTT */
+					0x00000000 /* EMC_CTT_DURATION */
+					0x8000308c /* EMC_DYN_SELF_REF_CONTROL */
+					0xe8000000 /* EMC_FBIO_SPARE */
+					0xff00ff49 /* EMC_CFG_RSV */
+				>;
+			};
+		};
+
+		emc-timings-2 {
+			nvidia,ram-code = <2>;  /* Hynix A RAM */
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200008>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-periodic-qrst;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-configuration = <
+					0x00000001 /* EMC_RC */
+					0x00000007 /* EMC_RFC */
+					0x00000000 /* EMC_RAS */
+					0x00000000 /* EMC_RP */
+					0x00000002 /* EMC_R2W */
+					0x0000000a /* EMC_W2R */
+					0x00000005 /* EMC_R2P */
+					0x0000000b /* EMC_W2P */
+					0x00000000 /* EMC_RD_RCD */
+					0x00000000 /* EMC_WR_RCD */
+					0x00000003 /* EMC_RRD */
+					0x00000001 /* EMC_REXT */
+					0x00000000 /* EMC_WEXT */
+					0x00000005 /* EMC_WDV */
+					0x00000005 /* EMC_QUSE */
+					0x00000004 /* EMC_QRST */
+					0x0000000a /* EMC_QSAFE */
+					0x0000000b /* EMC_RDV */
+					0x000000c0 /* EMC_REFRESH */
+					0x00000000 /* EMC_BURST_REFRESH_NUM */
+					0x00000030 /* EMC_PRE_REFRESH_REQ_CNT */
+					0x00000002 /* EMC_PDEX2WR */
+					0x00000002 /* EMC_PDEX2RD */
+					0x00000001 /* EMC_PCHG2PDEN */
+					0x00000000 /* EMC_ACT2PDEN */
+					0x00000007 /* EMC_AR2PDEN */
+					0x0000000f /* EMC_RW2PDEN */
+					0x00000008 /* EMC_TXSR */
+					0x00000008 /* EMC_TXSRDLL */
+					0x00000004 /* EMC_TCKE */
+					0x00000002 /* EMC_TFAW */
+					0x00000000 /* EMC_TRPAB */
+					0x00000004 /* EMC_TCLKSTABLE */
+					0x00000005 /* EMC_TCLKSTOP */
+					0x000000c7 /* EMC_TREFBW */
+					0x00000006 /* EMC_QUSE_EXTRA */
+					0x00000004 /* EMC_FBIO_CFG6 */
+					0x00000000 /* EMC_ODT_WRITE */
+					0x00000000 /* EMC_ODT_READ */
+					0x00004288 /* EMC_FBIO_CFG5 */
+					0x007800a4 /* EMC_CFG_DIG_DLL */
+					0x00008000 /* EMC_CFG_DIG_DLL_PERIOD */
+					0x000fc000 /* EMC_DLL_XFORM_DQS0 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS1 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS2 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS3 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS4 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS5 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS6 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS7 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE0 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE1 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE2 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE3 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE4 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE5 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE6 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE7 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS0 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS1 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS2 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS3 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS4 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS5 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS6 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS7 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ0 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ1 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ2 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ3 */
+					0x000002a0 /* EMC_XM2CMDPADCTRL */
+					0x0800211c /* EMC_XM2DQSPADCTRL2 */
+					0x00000000 /* EMC_XM2DQPADCTRL2 */
+					0x77fff884 /* EMC_XM2CLKPADCTRL */
+					0x01f1f108 /* EMC_XM2COMPPADCTRL */
+					0x05057404 /* EMC_XM2VTTGENPADCTRL */
+					0x54000007 /* EMC_XM2VTTGENPADCTRL2 */
+					0x08000168 /* EMC_XM2QUSEPADCTRL */
+					0x08000000 /* EMC_XM2DQSPADCTRL3 */
+					0x00000802 /* EMC_CTT_TERM_CTRL */
+					0x00000000 /* EMC_ZCAL_INTERVAL */
+					0x00000040 /* EMC_ZCAL_WAIT_CNT */
+					0x000c000c /* EMC_MRS_WAIT_CNT */
+					0xa0f10000 /* EMC_AUTO_CAL_CONFIG */
+					0x00000000 /* EMC_CTT */
+					0x00000000 /* EMC_CTT_DURATION */
+					0x80000287 /* EMC_DYN_SELF_REF_CONTROL */
+					0xe8000000 /* EMC_FBIO_SPARE */
+					0xff00ff00 /* EMC_CFG_RSV */
+				>;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200008>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-periodic-qrst;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-configuration = <
+					0x00000002 /* EMC_RC */
+					0x0000000f /* EMC_RFC */
+					0x00000001 /* EMC_RAS */
+					0x00000000 /* EMC_RP */
+					0x00000002 /* EMC_R2W */
+					0x0000000a /* EMC_W2R */
+					0x00000005 /* EMC_R2P */
+					0x0000000b /* EMC_W2P */
+					0x00000000 /* EMC_RD_RCD */
+					0x00000000 /* EMC_WR_RCD */
+					0x00000003 /* EMC_RRD */
+					0x00000001 /* EMC_REXT */
+					0x00000000 /* EMC_WEXT */
+					0x00000005 /* EMC_WDV */
+					0x00000005 /* EMC_QUSE */
+					0x00000004 /* EMC_QRST */
+					0x0000000a /* EMC_QSAFE */
+					0x0000000b /* EMC_RDV */
+					0x00000181 /* EMC_REFRESH */
+					0x00000000 /* EMC_BURST_REFRESH_NUM */
+					0x00000060 /* EMC_PRE_REFRESH_REQ_CNT */
+					0x00000002 /* EMC_PDEX2WR */
+					0x00000002 /* EMC_PDEX2RD */
+					0x00000001 /* EMC_PCHG2PDEN */
+					0x00000000 /* EMC_ACT2PDEN */
+					0x00000007 /* EMC_AR2PDEN */
+					0x0000000f /* EMC_RW2PDEN */
+					0x00000010 /* EMC_TXSR */
+					0x00000010 /* EMC_TXSRDLL */
+					0x00000004 /* EMC_TCKE */
+					0x00000003 /* EMC_TFAW */
+					0x00000000 /* EMC_TRPAB */
+					0x00000004 /* EMC_TCLKSTABLE */
+					0x00000005 /* EMC_TCLKSTOP */
+					0x0000018e /* EMC_TREFBW */
+					0x00000006 /* EMC_QUSE_EXTRA */
+					0x00000004 /* EMC_FBIO_CFG6 */
+					0x00000000 /* EMC_ODT_WRITE */
+					0x00000000 /* EMC_ODT_READ */
+					0x00004288 /* EMC_FBIO_CFG5 */
+					0x007800a4 /* EMC_CFG_DIG_DLL */
+					0x00008000 /* EMC_CFG_DIG_DLL_PERIOD */
+					0x000fc000 /* EMC_DLL_XFORM_DQS0 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS1 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS2 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS3 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS4 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS5 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS6 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS7 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE0 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE1 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE2 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE3 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE4 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE5 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE6 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE7 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS0 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS1 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS2 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS3 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS4 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS5 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS6 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS7 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ0 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ1 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ2 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ3 */
+					0x000002a0 /* EMC_XM2CMDPADCTRL */
+					0x0800211c /* EMC_XM2DQSPADCTRL2 */
+					0x00000000 /* EMC_XM2DQPADCTRL2 */
+					0x77fff884 /* EMC_XM2CLKPADCTRL */
+					0x01f1f108 /* EMC_XM2COMPPADCTRL */
+					0x05057404 /* EMC_XM2VTTGENPADCTRL */
+					0x54000007 /* EMC_XM2VTTGENPADCTRL2 */
+					0x08000168 /* EMC_XM2QUSEPADCTRL */
+					0x08000000 /* EMC_XM2DQSPADCTRL3 */
+					0x00000802 /* EMC_CTT_TERM_CTRL */
+					0x00000000 /* EMC_ZCAL_INTERVAL */
+					0x00000040 /* EMC_ZCAL_WAIT_CNT */
+					0x000c000c /* EMC_MRS_WAIT_CNT */
+					0xa0f10000 /* EMC_AUTO_CAL_CONFIG */
+					0x00000000 /* EMC_CTT */
+					0x00000000 /* EMC_CTT_DURATION */
+					0x8000040b /* EMC_DYN_SELF_REF_CONTROL */
+					0xe8000000 /* EMC_FBIO_SPARE */
+					0xff00ff00 /* EMC_CFG_RSV */
+				>;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200008>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-periodic-qrst;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-configuration = <
+					0x00000004 /* EMC_RC */
+					0x0000001e /* EMC_RFC */
+					0x00000003 /* EMC_RAS */
+					0x00000001 /* EMC_RP */
+					0x00000002 /* EMC_R2W */
+					0x0000000a /* EMC_W2R */
+					0x00000005 /* EMC_R2P */
+					0x0000000b /* EMC_W2P */
+					0x00000001 /* EMC_RD_RCD */
+					0x00000001 /* EMC_WR_RCD */
+					0x00000003 /* EMC_RRD */
+					0x00000001 /* EMC_REXT */
+					0x00000000 /* EMC_WEXT */
+					0x00000005 /* EMC_WDV */
+					0x00000005 /* EMC_QUSE */
+					0x00000004 /* EMC_QRST */
+					0x0000000a /* EMC_QSAFE */
+					0x0000000b /* EMC_RDV */
+					0x00000303 /* EMC_REFRESH */
+					0x00000000 /* EMC_BURST_REFRESH_NUM */
+					0x000000c0 /* EMC_PRE_REFRESH_REQ_CNT */
+					0x00000002 /* EMC_PDEX2WR */
+					0x00000002 /* EMC_PDEX2RD */
+					0x00000001 /* EMC_PCHG2PDEN */
+					0x00000000 /* EMC_ACT2PDEN */
+					0x00000007 /* EMC_AR2PDEN */
+					0x0000000f /* EMC_RW2PDEN */
+					0x00000020 /* EMC_TXSR */
+					0x00000020 /* EMC_TXSRDLL */
+					0x00000004 /* EMC_TCKE */
+					0x00000005 /* EMC_TFAW */
+					0x00000000 /* EMC_TRPAB */
+					0x00000004 /* EMC_TCLKSTABLE */
+					0x00000005 /* EMC_TCLKSTOP */
+					0x0000031c /* EMC_TREFBW */
+					0x00000006 /* EMC_QUSE_EXTRA */
+					0x00000004 /* EMC_FBIO_CFG6 */
+					0x00000000 /* EMC_ODT_WRITE */
+					0x00000000 /* EMC_ODT_READ */
+					0x00004288 /* EMC_FBIO_CFG5 */
+					0x007800a4 /* EMC_CFG_DIG_DLL */
+					0x00008000 /* EMC_CFG_DIG_DLL_PERIOD */
+					0x000fc000 /* EMC_DLL_XFORM_DQS0 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS1 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS2 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS3 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS4 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS5 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS6 */
+					0x000fc000 /* EMC_DLL_XFORM_DQS7 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE0 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE1 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE2 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE3 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE4 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE5 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE6 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE7 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS0 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS1 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS2 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS3 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS4 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS5 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS6 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS7 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ0 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ1 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ2 */
+					0x000fc000 /* EMC_DLL_XFORM_DQ3 */
+					0x000002a0 /* EMC_XM2CMDPADCTRL */
+					0x0800211c /* EMC_XM2DQSPADCTRL2 */
+					0x00000000 /* EMC_XM2DQPADCTRL2 */
+					0x77fff884 /* EMC_XM2CLKPADCTRL */
+					0x01f1f108 /* EMC_XM2COMPPADCTRL */
+					0x05057404 /* EMC_XM2VTTGENPADCTRL */
+					0x54000007 /* EMC_XM2VTTGENPADCTRL2 */
+					0x08000168 /* EMC_XM2QUSEPADCTRL */
+					0x08000000 /* EMC_XM2DQSPADCTRL3 */
+					0x00000802 /* EMC_CTT_TERM_CTRL */
+					0x00000000 /* EMC_ZCAL_INTERVAL */
+					0x00000040 /* EMC_ZCAL_WAIT_CNT */
+					0x000c000c /* EMC_MRS_WAIT_CNT */
+					0xa0f10000 /* EMC_AUTO_CAL_CONFIG */
+					0x00000000 /* EMC_CTT */
+					0x00000000 /* EMC_CTT_DURATION */
+					0x80000713 /* EMC_DYN_SELF_REF_CONTROL */
+					0xe8000000 /* EMC_FBIO_SPARE */
+					0xff00ff00 /* EMC_CFG_RSV */
+				>;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100003>;
+				nvidia,emc-mode-2 = <0x80200008>;
+				nvidia,emc-mode-reset = <0x80001221>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-periodic-qrst;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-configuration = <
+					0x00000009 /* EMC_RC */
+					0x0000003d /* EMC_RFC */
+					0x00000007 /* EMC_RAS */
+					0x00000002 /* EMC_RP */
+					0x00000002 /* EMC_R2W */
+					0x0000000a /* EMC_W2R */
+					0x00000005 /* EMC_R2P */
+					0x0000000b /* EMC_W2P */
+					0x00000002 /* EMC_RD_RCD */
+					0x00000002 /* EMC_WR_RCD */
+					0x00000003 /* EMC_RRD */
+					0x00000001 /* EMC_REXT */
+					0x00000000 /* EMC_WEXT */
+					0x00000005 /* EMC_WDV */
+					0x00000005 /* EMC_QUSE */
+					0x00000004 /* EMC_QRST */
+					0x0000000a /* EMC_QSAFE */
+					0x0000000b /* EMC_RDV */
+					0x00000607 /* EMC_REFRESH */
+					0x00000000 /* EMC_BURST_REFRESH_NUM */
+					0x00000181 /* EMC_PRE_REFRESH_REQ_CNT */
+					0x00000002 /* EMC_PDEX2WR */
+					0x00000002 /* EMC_PDEX2RD */
+					0x00000001 /* EMC_PCHG2PDEN */
+					0x00000000 /* EMC_ACT2PDEN */
+					0x00000007 /* EMC_AR2PDEN */
+					0x0000000f /* EMC_RW2PDEN */
+					0x00000040 /* EMC_TXSR */
+					0x00000040 /* EMC_TXSRDLL */
+					0x00000004 /* EMC_TCKE */
+					0x00000009 /* EMC_TFAW */
+					0x00000000 /* EMC_TRPAB */
+					0x00000004 /* EMC_TCLKSTABLE */
+					0x00000005 /* EMC_TCLKSTOP */
+					0x00000638 /* EMC_TREFBW */
+					0x00000006 /* EMC_QUSE_EXTRA */
+					0x00000006 /* EMC_FBIO_CFG6 */
+					0x00000000 /* EMC_ODT_WRITE */
+					0x00000000 /* EMC_ODT_READ */
+					0x00004288 /* EMC_FBIO_CFG5 */
+					0x004400a4 /* EMC_CFG_DIG_DLL */
+					0x00008000 /* EMC_CFG_DIG_DLL_PERIOD */
+					0x00080000 /* EMC_DLL_XFORM_DQS0 */
+					0x00080000 /* EMC_DLL_XFORM_DQS1 */
+					0x00080000 /* EMC_DLL_XFORM_DQS2 */
+					0x00080000 /* EMC_DLL_XFORM_DQS3 */
+					0x00080000 /* EMC_DLL_XFORM_DQS4 */
+					0x00080000 /* EMC_DLL_XFORM_DQS5 */
+					0x00080000 /* EMC_DLL_XFORM_DQS6 */
+					0x00080000 /* EMC_DLL_XFORM_DQS7 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE0 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE1 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE2 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE3 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE4 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE5 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE6 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE7 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS0 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS1 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS2 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS3 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS4 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS5 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS6 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS7 */
+					0x00080000 /* EMC_DLL_XFORM_DQ0 */
+					0x00080000 /* EMC_DLL_XFORM_DQ1 */
+					0x00080000 /* EMC_DLL_XFORM_DQ2 */
+					0x00080000 /* EMC_DLL_XFORM_DQ3 */
+					0x000002a0 /* EMC_XM2CMDPADCTRL */
+					0x0800211c /* EMC_XM2DQSPADCTRL2 */
+					0x00000000 /* EMC_XM2DQPADCTRL2 */
+					0x77fff884 /* EMC_XM2CLKPADCTRL */
+					0x01f1f108 /* EMC_XM2COMPPADCTRL */
+					0x05057404 /* EMC_XM2VTTGENPADCTRL */
+					0x54000007 /* EMC_XM2VTTGENPADCTRL2 */
+					0x08000168 /* EMC_XM2QUSEPADCTRL */
+					0x08000000 /* EMC_XM2DQSPADCTRL3 */
+					0x00000802 /* EMC_CTT_TERM_CTRL */
+					0x00020000 /* EMC_ZCAL_INTERVAL */
+					0x00000100 /* EMC_ZCAL_WAIT_CNT */
+					0x000c000c /* EMC_MRS_WAIT_CNT */
+					0xa0f10000 /* EMC_AUTO_CAL_CONFIG */
+					0x00000000 /* EMC_CTT */
+					0x00000000 /* EMC_CTT_DURATION */
+					0x80000d22 /* EMC_DYN_SELF_REF_CONTROL */
+					0xe8000000 /* EMC_FBIO_SPARE */
+					0xff00ff00 /* EMC_CFG_RSV */
+				>;
+			};
+
+			timing-400000000 {
+				clock-frequency = <400000000>;
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100002>;
+				nvidia,emc-mode-2 = <0x80200000>;
+				nvidia,emc-mode-reset = <0x80000521>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-configuration = <
+					0x00000012 /* EMC_RC */
+					0x00000076 /* EMC_RFC */
+					0x0000000c /* EMC_RAS */
+					0x00000004 /* EMC_RP */
+					0x00000003 /* EMC_R2W */
+					0x00000008 /* EMC_W2R */
+					0x00000002 /* EMC_R2P */
+					0x0000000a /* EMC_W2P */
+					0x00000004 /* EMC_RD_RCD */
+					0x00000004 /* EMC_WR_RCD */
+					0x00000002 /* EMC_RRD */
+					0x00000001 /* EMC_REXT */
+					0x00000000 /* EMC_WEXT */
+					0x00000004 /* EMC_WDV */
+					0x00000006 /* EMC_QUSE */
+					0x00000004 /* EMC_QRST */
+					0x0000000a /* EMC_QSAFE */
+					0x0000000c /* EMC_RDV */
+					0x00000bf0 /* EMC_REFRESH */
+					0x00000000 /* EMC_BURST_REFRESH_NUM */
+					0x000002fc /* EMC_PRE_REFRESH_REQ_CNT */
+					0x00000001 /* EMC_PDEX2WR */
+					0x00000008 /* EMC_PDEX2RD */
+					0x00000001 /* EMC_PCHG2PDEN */
+					0x00000000 /* EMC_ACT2PDEN */
+					0x00000008 /* EMC_AR2PDEN */
+					0x0000000f /* EMC_RW2PDEN */
+					0x0000007c /* EMC_TXSR */
+					0x00000200 /* EMC_TXSRDLL */
+					0x00000004 /* EMC_TCKE */
+					0x00000010 /* EMC_TFAW */
+					0x00000000 /* EMC_TRPAB */
+					0x00000004 /* EMC_TCLKSTABLE */
+					0x00000005 /* EMC_TCLKSTOP */
+					0x00000c30 /* EMC_TREFBW */
+					0x00000000 /* EMC_QUSE_EXTRA */
+					0x00000004 /* EMC_FBIO_CFG6 */
+					0x00000000 /* EMC_ODT_WRITE */
+					0x00000000 /* EMC_ODT_READ */
+					0x00007088 /* EMC_FBIO_CFG5 */
+					0x001d0084 /* EMC_CFG_DIG_DLL */
+					0x00008000 /* EMC_CFG_DIG_DLL_PERIOD */
+					0x00044000 /* EMC_DLL_XFORM_DQS0 */
+					0x00044000 /* EMC_DLL_XFORM_DQS1 */
+					0x00044000 /* EMC_DLL_XFORM_DQS2 */
+					0x00044000 /* EMC_DLL_XFORM_DQS3 */
+					0x00044000 /* EMC_DLL_XFORM_DQS4 */
+					0x00044000 /* EMC_DLL_XFORM_DQS5 */
+					0x00044000 /* EMC_DLL_XFORM_DQS6 */
+					0x00044000 /* EMC_DLL_XFORM_DQS7 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE0 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE1 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE2 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE3 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE4 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE5 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE6 */
+					0x00000000 /* EMC_DLL_XFORM_QUSE7 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS0 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS1 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS2 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS3 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS4 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS5 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS6 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS7 */
+					0x00058000 /* EMC_DLL_XFORM_DQ0 */
+					0x00058000 /* EMC_DLL_XFORM_DQ1 */
+					0x00058000 /* EMC_DLL_XFORM_DQ2 */
+					0x00058000 /* EMC_DLL_XFORM_DQ3 */
+					0x000002a0 /* EMC_XM2CMDPADCTRL */
+					0x0800013d /* EMC_XM2DQSPADCTRL2 */
+					0x00000000 /* EMC_XM2DQPADCTRL2 */
+					0x77fff884 /* EMC_XM2CLKPADCTRL */
+					0x01f1f508 /* EMC_XM2COMPPADCTRL */
+					0x05057404 /* EMC_XM2VTTGENPADCTRL */
+					0x54000007 /* EMC_XM2VTTGENPADCTRL2 */
+					0x080001e8 /* EMC_XM2QUSEPADCTRL */
+					0x08000021 /* EMC_XM2DQSPADCTRL3 */
+					0x00000802 /* EMC_CTT_TERM_CTRL */
+					0x00020000 /* EMC_ZCAL_INTERVAL */
+					0x00000100 /* EMC_ZCAL_WAIT_CNT */
+					0x0148000c /* EMC_MRS_WAIT_CNT */
+					0xa0f10000 /* EMC_AUTO_CAL_CONFIG */
+					0x00000000 /* EMC_CTT */
+					0x00000000 /* EMC_CTT_DURATION */
+					0x800018c8 /* EMC_DYN_SELF_REF_CONTROL */
+					0xe8000000 /* EMC_FBIO_SPARE */
+					0xff00ff89 /* EMC_CFG_RSV */
+				>;
+			};
+
+			timing-800000000 {
+				clock-frequency = <800000000>;
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x80100002>;
+				nvidia,emc-mode-2 = <0x80200018>;
+				nvidia,emc-mode-reset = <0x80000d71>;
+				nvidia,emc-zcal-cnt-long = <0x00000040>;
+				nvidia,emc-cfg-periodic-qrst;
+				nvidia,emc-configuration = <
+					0x00000025 /* EMC_RC */
+					0x000000ee /* EMC_RFC */
+					0x0000001a /* EMC_RAS */
+					0x00000009 /* EMC_RP */
+					0x00000005 /* EMC_R2W */
+					0x0000000d /* EMC_W2R */
+					0x00000004 /* EMC_R2P */
+					0x00000013 /* EMC_W2P */
+					0x00000009 /* EMC_RD_RCD */
+					0x00000009 /* EMC_WR_RCD */
+					0x00000003 /* EMC_RRD */
+					0x00000001 /* EMC_REXT */
+					0x00000000 /* EMC_WEXT */
+					0x00000007 /* EMC_WDV */
+					0x0000000a /* EMC_QUSE */
+					0x00000009 /* EMC_QRST */
+					0x0000000b /* EMC_QSAFE */
+					0x00000011 /* EMC_RDV */
+					0x00001820 /* EMC_REFRESH */
+					0x00000000 /* EMC_BURST_REFRESH_NUM */
+					0x00000608 /* EMC_PRE_REFRESH_REQ_CNT */
+					0x00000003 /* EMC_PDEX2WR */
+					0x00000012 /* EMC_PDEX2RD */
+					0x00000001 /* EMC_PCHG2PDEN */
+					0x00000000 /* EMC_ACT2PDEN */
+					0x0000000f /* EMC_AR2PDEN */
+					0x00000018 /* EMC_RW2PDEN */
+					0x000000f8 /* EMC_TXSR */
+					0x00000200 /* EMC_TXSRDLL */
+					0x00000005 /* EMC_TCKE */
+					0x00000020 /* EMC_TFAW */
+					0x00000000 /* EMC_TRPAB */
+					0x00000007 /* EMC_TCLKSTABLE */
+					0x00000008 /* EMC_TCLKSTOP */
+					0x00001860 /* EMC_TREFBW */
+					0x0000000b /* EMC_QUSE_EXTRA */
+					0x00000006 /* EMC_FBIO_CFG6 */
+					0x00000000 /* EMC_ODT_WRITE */
+					0x00000000 /* EMC_ODT_READ */
+					0x00005088 /* EMC_FBIO_CFG5 */
+					0xf0070191 /* EMC_CFG_DIG_DLL */
+					0x00008000 /* EMC_CFG_DIG_DLL_PERIOD */
+					0x0000000c /* EMC_DLL_XFORM_DQS0 */
+					0x007fc00a /* EMC_DLL_XFORM_DQS1 */
+					0x00000008 /* EMC_DLL_XFORM_DQS2 */
+					0x0000000a /* EMC_DLL_XFORM_DQS3 */
+					0x0000000a /* EMC_DLL_XFORM_DQS4 */
+					0x0000000a /* EMC_DLL_XFORM_DQS5 */
+					0x0000000a /* EMC_DLL_XFORM_DQS6 */
+					0x0000000a /* EMC_DLL_XFORM_DQS7 */
+					0x00018000 /* EMC_DLL_XFORM_QUSE0 */
+					0x00018000 /* EMC_DLL_XFORM_QUSE1 */
+					0x00018000 /* EMC_DLL_XFORM_QUSE2 */
+					0x00018000 /* EMC_DLL_XFORM_QUSE3 */
+					0x00018000 /* EMC_DLL_XFORM_QUSE4 */
+					0x00018000 /* EMC_DLL_XFORM_QUSE5 */
+					0x00018000 /* EMC_DLL_XFORM_QUSE6 */
+					0x00018000 /* EMC_DLL_XFORM_QUSE7 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS0 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS1 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS2 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS3 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS4 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS5 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS6 */
+					0x00000000 /* EMC_DLI_TRIM_TXDQS7 */
+					0x0000000a /* EMC_DLL_XFORM_DQ0 */
+					0x0000000c /* EMC_DLL_XFORM_DQ1 */
+					0x0000000a /* EMC_DLL_XFORM_DQ2 */
+					0x0000000a /* EMC_DLL_XFORM_DQ3 */
+					0x000002a0 /* EMC_XM2CMDPADCTRL */
+					0x0600013d /* EMC_XM2DQSPADCTRL2 */
+					0x22220000 /* EMC_XM2DQPADCTRL2 */
+					0x77fff884 /* EMC_XM2CLKPADCTRL */
+					0x01f1f501 /* EMC_XM2COMPPADCTRL */
+					0x07077404 /* EMC_XM2VTTGENPADCTRL */
+					0x54000000 /* EMC_XM2VTTGENPADCTRL2 */
+					0x080001e8 /* EMC_XM2QUSEPADCTRL */
+					0x0a000021 /* EMC_XM2DQSPADCTRL3 */
+					0x00000802 /* EMC_CTT_TERM_CTRL */
+					0x00020000 /* EMC_ZCAL_INTERVAL */
+					0x00000100 /* EMC_ZCAL_WAIT_CNT */
+					0x00d0000c /* EMC_MRS_WAIT_CNT */
+					0xa0f10000 /* EMC_AUTO_CAL_CONFIG */
+					0x00000000 /* EMC_CTT */
+					0x00000000 /* EMC_CTT_DURATION */
+					0x8000308c /* EMC_DYN_SELF_REF_CONTROL */
+					0xe8000000 /* EMC_FBIO_SPARE */
+					0xff00ff49 /* EMC_CFG_RSV */
+				>;
+			};
+		};
 	};
 
 	hda@70030000 {
@@ -359,7 +4553,7 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		smsc@2 { /* SMSC 10/100T Ethernet Controller */
+		ethernet@2 { /* SMSC 10/100T Ethernet Controller */
 			compatible = "usb424,9e00";
 			reg = <2>;
 			local-mac-address = [00 11 22 33 44 55];
@@ -570,7 +4764,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		power {
+		key-power {
 			gpios = <&gpio TEGRA_GPIO(V, 0) GPIO_ACTIVE_LOW>;
 			debounce-interval = <10>;
 			linux,code = <KEY_POWER>;
@@ -592,3940 +4786,11 @@
 		};
 	};
 };
-&mc_timings {
-	emc-timings-0 {
-		nvidia,ram-code = <0>; /* Samsung RAM */
-		timing-25500000 {
-			clock-frequency = <25500000>;
-			nvidia,emem-configuration = <
-				0x00030003 /* MC_EMEM_ARB_CFG */
-				0xc0000010 /* MC_EMEM_ARB_OUTSTANDING_REQ */
-				0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
-				0x00000001 /* MC_EMEM_ARB_TIMING_RP */
-				0x00000002 /* MC_EMEM_ARB_TIMING_RC */
-				0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
-				0x00000001 /* MC_EMEM_ARB_TIMING_FAW */
-				0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
-				0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-				0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
-				0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
-				0x00000001 /* MC_EMEM_ARB_TIMING_W2W */
-				0x00000002 /* MC_EMEM_ARB_TIMING_R2W */
-				0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
-				0x06020102 /* MC_EMEM_ARB_DA_TURNS */
-				0x000a0502 /* MC_EMEM_ARB_DA_COVERS */
-				0x75830303 /* MC_EMEM_ARB_MISC0 */
-				0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-			>;
-		};
-		timing-51000000 {
-			clock-frequency = <51000000>;
-			nvidia,emem-configuration = <
-				0x00010003 /* MC_EMEM_ARB_CFG */
-				0xc0000010 /* MC_EMEM_ARB_OUTSTANDING_REQ */
-				0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
-				0x00000001 /* MC_EMEM_ARB_TIMING_RP */
-				0x00000002 /* MC_EMEM_ARB_TIMING_RC */
-				0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
-				0x00000001 /* MC_EMEM_ARB_TIMING_FAW */
-				0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
-				0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-				0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
-				0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
-				0x00000001 /* MC_EMEM_ARB_TIMING_W2W */
-				0x00000002 /* MC_EMEM_ARB_TIMING_R2W */
-				0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
-				0x06020102 /* MC_EMEM_ARB_DA_TURNS */
-				0x000a0502 /* MC_EMEM_ARB_DA_COVERS */
-				0x74630303 /* MC_EMEM_ARB_MISC0 */
-				0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-			>;
-		};
-		timing-102000000 {
-			clock-frequency = <102000000>;
-			nvidia,emem-configuration = <
-				0x00000003 /* MC_EMEM_ARB_CFG */
-				0xc0000018 /* MC_EMEM_ARB_OUTSTANDING_REQ */
-				0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
-				0x00000001 /* MC_EMEM_ARB_TIMING_RP */
-				0x00000003 /* MC_EMEM_ARB_TIMING_RC */
-				0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
-				0x00000002 /* MC_EMEM_ARB_TIMING_FAW */
-				0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
-				0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-				0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
-				0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
-				0x00000001 /* MC_EMEM_ARB_TIMING_W2W */
-				0x00000002 /* MC_EMEM_ARB_TIMING_R2W */
-				0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
-				0x06020102 /* MC_EMEM_ARB_DA_TURNS */
-				0x000a0503 /* MC_EMEM_ARB_DA_COVERS */
-				0x73c30504 /* MC_EMEM_ARB_MISC0 */
-				0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-			>;
-		};
-		timing-204000000 {
-			clock-frequency = <204000000>;
-			nvidia,emem-configuration = <
-				0x00000006 /* MC_EMEM_ARB_CFG */
-				0xc0000025 /* MC_EMEM_ARB_OUTSTANDING_REQ */
-				0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
-				0x00000001 /* MC_EMEM_ARB_TIMING_RP */
-				0x00000005 /* MC_EMEM_ARB_TIMING_RC */
-				0x00000002 /* MC_EMEM_ARB_TIMING_RAS */
-				0x00000004 /* MC_EMEM_ARB_TIMING_FAW */
-				0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
-				0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-				0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
-				0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
-				0x00000001 /* MC_EMEM_ARB_TIMING_W2W */
-				0x00000002 /* MC_EMEM_ARB_TIMING_R2W */
-				0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
-				0x06020102 /* MC_EMEM_ARB_DA_TURNS */
-				0x000a0505 /* MC_EMEM_ARB_DA_COVERS */
-				0x73840a06 /* MC_EMEM_ARB_MISC0 */
-				0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-			>;
-		};
-		timing-400000000 {
-			clock-frequency = <400000000>;
-			nvidia,emem-configuration = <
-				0x0000000c /* MC_EMEM_ARB_CFG */
-				0xc0000048 /* MC_EMEM_ARB_OUTSTANDING_REQ */
-				0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
-				0x00000002 /* MC_EMEM_ARB_TIMING_RP */
-				0x00000009 /* MC_EMEM_ARB_TIMING_RC */
-				0x00000005 /* MC_EMEM_ARB_TIMING_RAS */
-				0x00000007 /* MC_EMEM_ARB_TIMING_FAW */
-				0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
-				0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-				0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
-				0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
-				0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
-				0x00000003 /* MC_EMEM_ARB_TIMING_R2W */
-				0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
-				0x06030202 /* MC_EMEM_ARB_DA_TURNS */
-				0x000d0709 /* MC_EMEM_ARB_DA_COVERS */
-				0x7086120a /* MC_EMEM_ARB_MISC0 */
-				0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-			>;
-		};
-		timing-800000000 {
-			clock-frequency = <800000000>;
-			nvidia,emem-configuration = <
-				0x00000018 /* MC_EMEM_ARB_CFG */
-				0xc0000090 /* MC_EMEM_ARB_OUTSTANDING_REQ */
-				0x00000004 /* MC_EMEM_ARB_TIMING_RCD */
-				0x00000005 /* MC_EMEM_ARB_TIMING_RP */
-				0x00000013 /* MC_EMEM_ARB_TIMING_RC */
-				0x0000000c /* MC_EMEM_ARB_TIMING_RAS */
-				0x0000000f /* MC_EMEM_ARB_TIMING_FAW */
-				0x00000002 /* MC_EMEM_ARB_TIMING_RRD */
-				0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-				0x0000000c /* MC_EMEM_ARB_TIMING_WAP2PRE */
-				0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
-				0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
-				0x00000004 /* MC_EMEM_ARB_TIMING_R2W */
-				0x00000008 /* MC_EMEM_ARB_TIMING_W2R */
-				0x08040202 /* MC_EMEM_ARB_DA_TURNS */
-				0x00160d13 /* MC_EMEM_ARB_DA_COVERS */
-				0x712c2414 /* MC_EMEM_ARB_MISC0 */
-				0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-			>;
-		};
-	};
-	emc-timings-1 {
-		nvidia,ram-code = <1>; /* Hynix M RAM */
-		timing-25500000 {
-			clock-frequency = <25500000>;
-			nvidia,emem-configuration = <
-				0x00030003 /* MC_EMEM_ARB_CFG */
-				0xc0000010 /* MC_EMEM_ARB_OUTSTANDING_REQ */
-				0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
-				0x00000001 /* MC_EMEM_ARB_TIMING_RP */
-				0x00000002 /* MC_EMEM_ARB_TIMING_RC */
-				0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
-				0x00000001 /* MC_EMEM_ARB_TIMING_FAW */
-				0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
-				0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-				0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
-				0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
-				0x00000001 /* MC_EMEM_ARB_TIMING_W2W */
-				0x00000002 /* MC_EMEM_ARB_TIMING_R2W */
-				0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
-				0x06020102 /* MC_EMEM_ARB_DA_TURNS */
-				0x000a0502 /* MC_EMEM_ARB_DA_COVERS */
-				0x75830303 /* MC_EMEM_ARB_MISC0 */
-				0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-			>;
-		};
-		timing-51000000 {
-			clock-frequency = <51000000>;
-			nvidia,emem-configuration = <
-				0x00010003 /* MC_EMEM_ARB_CFG */
-				0xc0000010 /* MC_EMEM_ARB_OUTSTANDING_REQ */
-				0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
-				0x00000001 /* MC_EMEM_ARB_TIMING_RP */
-				0x00000002 /* MC_EMEM_ARB_TIMING_RC */
-				0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
-				0x00000001 /* MC_EMEM_ARB_TIMING_FAW */
-				0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
-				0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-				0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
-				0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
-				0x00000001 /* MC_EMEM_ARB_TIMING_W2W */
-				0x00000002 /* MC_EMEM_ARB_TIMING_R2W */
-				0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
-				0x06020102 /* MC_EMEM_ARB_DA_TURNS */
-				0x000a0502 /* MC_EMEM_ARB_DA_COVERS */
-				0x74630303 /* MC_EMEM_ARB_MISC0 */
-				0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-			>;
-		};
-		timing-102000000 {
-			clock-frequency = <102000000>;
-			nvidia,emem-configuration = <
-				0x00000003 /* MC_EMEM_ARB_CFG */
-				0xc0000018 /* MC_EMEM_ARB_OUTSTANDING_REQ */
-				0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
-				0x00000001 /* MC_EMEM_ARB_TIMING_RP */
-				0x00000003 /* MC_EMEM_ARB_TIMING_RC */
-				0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
-				0x00000002 /* MC_EMEM_ARB_TIMING_FAW */
-				0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
-				0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-				0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
-				0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
-				0x00000001 /* MC_EMEM_ARB_TIMING_W2W */
-				0x00000002 /* MC_EMEM_ARB_TIMING_R2W */
-				0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
-				0x06020102 /* MC_EMEM_ARB_DA_TURNS */
-				0x000a0503 /* MC_EMEM_ARB_DA_COVERS */
-				0x73c30504 /* MC_EMEM_ARB_MISC0 */
-				0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-			>;
-		};
-		timing-204000000 {
-			clock-frequency = <204000000>;
-			nvidia,emem-configuration = <
-				0x00000006 /* MC_EMEM_ARB_CFG */
-				0xc0000025 /* MC_EMEM_ARB_OUTSTANDING_REQ */
-				0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
-				0x00000001 /* MC_EMEM_ARB_TIMING_RP */
-				0x00000005 /* MC_EMEM_ARB_TIMING_RC */
-				0x00000002 /* MC_EMEM_ARB_TIMING_RAS */
-				0x00000004 /* MC_EMEM_ARB_TIMING_FAW */
-				0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
-				0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-				0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
-				0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
-				0x00000001 /* MC_EMEM_ARB_TIMING_W2W */
-				0x00000002 /* MC_EMEM_ARB_TIMING_R2W */
-				0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
-				0x06020102 /* MC_EMEM_ARB_DA_TURNS */
-				0x000a0505 /* MC_EMEM_ARB_DA_COVERS */
-				0x73840a06 /* MC_EMEM_ARB_MISC0 */
-				0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-			>;
-		};
-		timing-400000000 {
-			clock-frequency = <400000000>;
-			nvidia,emem-configuration = <
-				0x0000000c /* MC_EMEM_ARB_CFG */
-				0xc0000048 /* MC_EMEM_ARB_OUTSTANDING_REQ */
-				0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
-				0x00000002 /* MC_EMEM_ARB_TIMING_RP */
-				0x00000009 /* MC_EMEM_ARB_TIMING_RC */
-				0x00000005 /* MC_EMEM_ARB_TIMING_RAS */
-				0x00000007 /* MC_EMEM_ARB_TIMING_FAW */
-				0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
-				0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-				0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
-				0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
-				0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
-				0x00000003 /* MC_EMEM_ARB_TIMING_R2W */
-				0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
-				0x06030202 /* MC_EMEM_ARB_DA_TURNS */
-				0x000d0709 /* MC_EMEM_ARB_DA_COVERS */
-				0x7086120a /* MC_EMEM_ARB_MISC0 */
-				0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-			>;
-		};
-		timing-800000000 {
-			clock-frequency = <800000000>;
-			nvidia,emem-configuration = <
-				0x00000018 /* MC_EMEM_ARB_CFG */
-				0xc0000090 /* MC_EMEM_ARB_OUTSTANDING_REQ */
-				0x00000004 /* MC_EMEM_ARB_TIMING_RCD */
-				0x00000005 /* MC_EMEM_ARB_TIMING_RP */
-				0x00000013 /* MC_EMEM_ARB_TIMING_RC */
-				0x0000000c /* MC_EMEM_ARB_TIMING_RAS */
-				0x0000000f /* MC_EMEM_ARB_TIMING_FAW */
-				0x00000002 /* MC_EMEM_ARB_TIMING_RRD */
-				0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-				0x0000000c /* MC_EMEM_ARB_TIMING_WAP2PRE */
-				0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
-				0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
-				0x00000004 /* MC_EMEM_ARB_TIMING_R2W */
-				0x00000008 /* MC_EMEM_ARB_TIMING_W2R */
-				0x08040202 /* MC_EMEM_ARB_DA_TURNS */
-				0x00160d13 /* MC_EMEM_ARB_DA_COVERS */
-				0x712c2414 /* MC_EMEM_ARB_MISC0 */
-				0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-			>;
-		};
-	};
-	emc-timings-2 {
-		nvidia,ram-code = <2>; /* Hynix A RAM */
-		timing-25500000 {
-			clock-frequency = <25500000>;
-			nvidia,emem-configuration = <
-				0x00030003 /* MC_EMEM_ARB_CFG */
-				0xc0000010 /* MC_EMEM_ARB_OUTSTANDING_REQ */
-				0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
-				0x00000001 /* MC_EMEM_ARB_TIMING_RP */
-				0x00000002 /* MC_EMEM_ARB_TIMING_RC */
-				0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
-				0x00000001 /* MC_EMEM_ARB_TIMING_FAW */
-				0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
-				0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-				0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
-				0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
-				0x00000001 /* MC_EMEM_ARB_TIMING_W2W */
-				0x00000002 /* MC_EMEM_ARB_TIMING_R2W */
-				0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
-				0x06020102 /* MC_EMEM_ARB_DA_TURNS */
-				0x000a0502 /* MC_EMEM_ARB_DA_COVERS */
-				0x75e30303 /* MC_EMEM_ARB_MISC0 */
-				0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-			>;
-		};
-		timing-51000000 {
-			clock-frequency = <51000000>;
-			nvidia,emem-configuration = <
-				0x00010003 /* MC_EMEM_ARB_CFG */
-				0xc0000010 /* MC_EMEM_ARB_OUTSTANDING_REQ */
-				0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
-				0x00000001 /* MC_EMEM_ARB_TIMING_RP */
-				0x00000002 /* MC_EMEM_ARB_TIMING_RC */
-				0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
-				0x00000001 /* MC_EMEM_ARB_TIMING_FAW */
-				0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
-				0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-				0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
-				0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
-				0x00000001 /* MC_EMEM_ARB_TIMING_W2W */
-				0x00000002 /* MC_EMEM_ARB_TIMING_R2W */
-				0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
-				0x06020102 /* MC_EMEM_ARB_DA_TURNS */
-				0x000a0502 /* MC_EMEM_ARB_DA_COVERS */
-				0x74e30303 /* MC_EMEM_ARB_MISC0 */
-				0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-			>;
-		};
-		timing-102000000 {
-			clock-frequency = <102000000>;
-			nvidia,emem-configuration = <
-				0x00000003 /* MC_EMEM_ARB_CFG */
-				0xc0000018 /* MC_EMEM_ARB_OUTSTANDING_REQ */
-				0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
-				0x00000001 /* MC_EMEM_ARB_TIMING_RP */
-				0x00000003 /* MC_EMEM_ARB_TIMING_RC */
-				0x00000000 /* MC_EMEM_ARB_TIMING_RAS */
-				0x00000002 /* MC_EMEM_ARB_TIMING_FAW */
-				0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
-				0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-				0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
-				0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
-				0x00000001 /* MC_EMEM_ARB_TIMING_W2W */
-				0x00000002 /* MC_EMEM_ARB_TIMING_R2W */
-				0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
-				0x06020102 /* MC_EMEM_ARB_DA_TURNS */
-				0x000a0503 /* MC_EMEM_ARB_DA_COVERS */
-				0x74430504 /* MC_EMEM_ARB_MISC0 */
-				0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-			>;
-		};
-		timing-204000000 {
-			clock-frequency = <204000000>;
-			nvidia,emem-configuration = <
-				0x00000006 /* MC_EMEM_ARB_CFG */
-				0xc0000025 /* MC_EMEM_ARB_OUTSTANDING_REQ */
-				0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
-				0x00000001 /* MC_EMEM_ARB_TIMING_RP */
-				0x00000005 /* MC_EMEM_ARB_TIMING_RC */
-				0x00000002 /* MC_EMEM_ARB_TIMING_RAS */
-				0x00000004 /* MC_EMEM_ARB_TIMING_FAW */
-				0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
-				0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-				0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
-				0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
-				0x00000001 /* MC_EMEM_ARB_TIMING_W2W */
-				0x00000002 /* MC_EMEM_ARB_TIMING_R2W */
-				0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
-				0x06020102 /* MC_EMEM_ARB_DA_TURNS */
-				0x000a0505 /* MC_EMEM_ARB_DA_COVERS */
-				0x74040a06 /* MC_EMEM_ARB_MISC0 */
-				0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-			>;
-		};
-		timing-400000000 {
-			clock-frequency = <400000000>;
-			nvidia,emem-configuration = <
-				0x0000000c /* MC_EMEM_ARB_CFG */
-				0xc0000048 /* MC_EMEM_ARB_OUTSTANDING_REQ */
-				0x00000001 /* MC_EMEM_ARB_TIMING_RCD */
-				0x00000002 /* MC_EMEM_ARB_TIMING_RP */
-				0x00000009 /* MC_EMEM_ARB_TIMING_RC */
-				0x00000005 /* MC_EMEM_ARB_TIMING_RAS */
-				0x00000007 /* MC_EMEM_ARB_TIMING_FAW */
-				0x00000001 /* MC_EMEM_ARB_TIMING_RRD */
-				0x00000002 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-				0x00000008 /* MC_EMEM_ARB_TIMING_WAP2PRE */
-				0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
-				0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
-				0x00000003 /* MC_EMEM_ARB_TIMING_R2W */
-				0x00000006 /* MC_EMEM_ARB_TIMING_W2R */
-				0x06030202 /* MC_EMEM_ARB_DA_TURNS */
-				0x000d0709 /* MC_EMEM_ARB_DA_COVERS */
-				0x7086120a /* MC_EMEM_ARB_MISC0 */
-				0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-			>;
-		};
-		timing-800000000 {
-			clock-frequency = <800000000>;
-			nvidia,emem-configuration = <
-				0x00000018 /* MC_EMEM_ARB_CFG */
-				0xc0000090 /* MC_EMEM_ARB_OUTSTANDING_REQ */
-				0x00000004 /* MC_EMEM_ARB_TIMING_RCD */
-				0x00000005 /* MC_EMEM_ARB_TIMING_RP */
-				0x00000013 /* MC_EMEM_ARB_TIMING_RC */
-				0x0000000c /* MC_EMEM_ARB_TIMING_RAS */
-				0x0000000f /* MC_EMEM_ARB_TIMING_FAW */
-				0x00000002 /* MC_EMEM_ARB_TIMING_RRD */
-				0x00000003 /* MC_EMEM_ARB_TIMING_RAP2PRE */
-				0x0000000c /* MC_EMEM_ARB_TIMING_WAP2PRE */
-				0x00000002 /* MC_EMEM_ARB_TIMING_R2R */
-				0x00000002 /* MC_EMEM_ARB_TIMING_W2W */
-				0x00000004 /* MC_EMEM_ARB_TIMING_R2W */
-				0x00000008 /* MC_EMEM_ARB_TIMING_W2R */
-				0x08040202 /* MC_EMEM_ARB_DA_TURNS */
-				0x00160d13 /* MC_EMEM_ARB_DA_COVERS */
-				0x712c2414 /* MC_EMEM_ARB_MISC0 */
-				0x001f0000 /* MC_EMEM_ARB_RING1_THROTTLE */
-			>;
-		};
-	};
-};
-&emc_timings {
-	emc-timings-0 {
-		nvidia,ram-code = <0>;  /* Samsung RAM */
-		timing-25500000 {
-			clock-frequency = <25500000>;
-			nvidia,emc-auto-cal-interval = <0x001fffff>;
-			nvidia,emc-mode-1 = <0x80100003>;
-			nvidia,emc-mode-2 = <0x80200008>;
-			nvidia,emc-mode-reset = <0x80001221>;
-			nvidia,emc-zcal-cnt-long = <0x00000040>;
-			nvidia,emc-cfg-periodic-qrst;
-			nvidia,emc-cfg-dyn-self-ref;
-			nvidia,emc-configuration = <
-				0x00000001 /* EMC_RC */
-				0x00000006 /* EMC_RFC */
-				0x00000000 /* EMC_RAS */
-				0x00000000 /* EMC_RP */
-				0x00000002 /* EMC_R2W */
-				0x0000000a /* EMC_W2R */
-				0x00000005 /* EMC_R2P */
-				0x0000000b /* EMC_W2P */
-				0x00000000 /* EMC_RD_RCD */
-				0x00000000 /* EMC_WR_RCD */
-				0x00000003 /* EMC_RRD */
-				0x00000001 /* EMC_REXT */
-				0x00000000 /* EMC_WEXT */
-				0x00000005 /* EMC_WDV */
-				0x00000005 /* EMC_QUSE */
-				0x00000004 /* EMC_QRST */
-				0x0000000a /* EMC_QSAFE */
-				0x0000000b /* EMC_RDV */
-				0x000000c0 /* EMC_REFRESH */
-				0x00000000 /* EMC_BURST_REFRESH_NUM */
-				0x00000030 /* EMC_PRE_REFRESH_REQ_CNT */
-				0x00000002 /* EMC_PDEX2WR */
-				0x00000002 /* EMC_PDEX2RD */
-				0x00000001 /* EMC_PCHG2PDEN */
-				0x00000000 /* EMC_ACT2PDEN */
-				0x00000007 /* EMC_AR2PDEN */
-				0x0000000f /* EMC_RW2PDEN */
-				0x00000007 /* EMC_TXSR */
-				0x00000007 /* EMC_TXSRDLL */
-				0x00000004 /* EMC_TCKE */
-				0x00000002 /* EMC_TFAW */
-				0x00000000 /* EMC_TRPAB */
-				0x00000004 /* EMC_TCLKSTABLE */
-				0x00000005 /* EMC_TCLKSTOP */
-				0x000000c7 /* EMC_TREFBW */
-				0x00000006 /* EMC_QUSE_EXTRA */
-				0x00000004 /* EMC_FBIO_CFG6 */
-				0x00000000 /* EMC_ODT_WRITE */
-				0x00000000 /* EMC_ODT_READ */
-				0x00004288 /* EMC_FBIO_CFG5 */
-				0x007800a4 /* EMC_CFG_DIG_DLL */
-				0x00008000 /* EMC_CFG_DIG_DLL_PERIOD */
-				0x000fc000 /* EMC_DLL_XFORM_DQS0 */
-				0x000fc000 /* EMC_DLL_XFORM_DQS1 */
-				0x000fc000 /* EMC_DLL_XFORM_DQS2 */
-				0x000fc000 /* EMC_DLL_XFORM_DQS3 */
-				0x000fc000 /* EMC_DLL_XFORM_DQS4 */
-				0x000fc000 /* EMC_DLL_XFORM_DQS5 */
-				0x000fc000 /* EMC_DLL_XFORM_DQS6 */
-				0x000fc000 /* EMC_DLL_XFORM_DQS7 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE0 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE1 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE2 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE3 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE4 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE5 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE6 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE7 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS0 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS1 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS2 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS3 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS4 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS5 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS6 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS7 */
-				0x000fc000 /* EMC_DLL_XFORM_DQ0 */
-				0x000fc000 /* EMC_DLL_XFORM_DQ1 */
-				0x000fc000 /* EMC_DLL_XFORM_DQ2 */
-				0x000fc000 /* EMC_DLL_XFORM_DQ3 */
-				0x000002a0 /* EMC_XM2CMDPADCTRL */
-				0x0800211c /* EMC_XM2DQSPADCTRL2 */
-				0x00000000 /* EMC_XM2DQPADCTRL2 */
-				0x77fff884 /* EMC_XM2CLKPADCTRL */
-				0x01f1f108 /* EMC_XM2COMPPADCTRL */
-				0x05057404 /* EMC_XM2VTTGENPADCTRL */
-				0x54000007 /* EMC_XM2VTTGENPADCTRL2 */
-				0x08000168 /* EMC_XM2QUSEPADCTRL */
-				0x08000000 /* EMC_XM2DQSPADCTRL3 */
-				0x00000802 /* EMC_CTT_TERM_CTRL */
-				0x00000000 /* EMC_ZCAL_INTERVAL */
-				0x00000040 /* EMC_ZCAL_WAIT_CNT */
-				0x000c000c /* EMC_MRS_WAIT_CNT */
-				0xa0f10000 /* EMC_AUTO_CAL_CONFIG */
-				0x00000000 /* EMC_CTT */
-				0x00000000 /* EMC_CTT_DURATION */
-				0x80000287 /* EMC_DYN_SELF_REF_CONTROL */
-				0xe8000000 /* EMC_FBIO_SPARE */
-				0xff00ff00 /* EMC_CFG_RSV */
-			>;
-		};
-		timing-51000000 {
-			clock-frequency = <51000000>;
-			nvidia,emc-auto-cal-interval = <0x001fffff>;
-			nvidia,emc-mode-1 = <0x80100003>;
-			nvidia,emc-mode-2 = <0x80200008>;
-			nvidia,emc-mode-reset = <0x80001221>;
-			nvidia,emc-zcal-cnt-long = <0x00000040>;
-			nvidia,emc-cfg-periodic-qrst;
-			nvidia,emc-cfg-dyn-self-ref;
-			nvidia,emc-configuration = <
-				0x00000002 /* EMC_RC */
-				0x0000000d /* EMC_RFC */
-				0x00000001 /* EMC_RAS */
-				0x00000000 /* EMC_RP */
-				0x00000002 /* EMC_R2W */
-				0x0000000a /* EMC_W2R */
-				0x00000005 /* EMC_R2P */
-				0x0000000b /* EMC_W2P */
-				0x00000000 /* EMC_RD_RCD */
-				0x00000000 /* EMC_WR_RCD */
-				0x00000003 /* EMC_RRD */
-				0x00000001 /* EMC_REXT */
-				0x00000000 /* EMC_WEXT */
-				0x00000005 /* EMC_WDV */
-				0x00000005 /* EMC_QUSE */
-				0x00000004 /* EMC_QRST */
-				0x0000000a /* EMC_QSAFE */
-				0x0000000b /* EMC_RDV */
-				0x00000181 /* EMC_REFRESH */
-				0x00000000 /* EMC_BURST_REFRESH_NUM */
-				0x00000060 /* EMC_PRE_REFRESH_REQ_CNT */
-				0x00000002 /* EMC_PDEX2WR */
-				0x00000002 /* EMC_PDEX2RD */
-				0x00000001 /* EMC_PCHG2PDEN */
-				0x00000000 /* EMC_ACT2PDEN */
-				0x00000007 /* EMC_AR2PDEN */
-				0x0000000f /* EMC_RW2PDEN */
-				0x0000000e /* EMC_TXSR */
-				0x0000000e /* EMC_TXSRDLL */
-				0x00000004 /* EMC_TCKE */
-				0x00000003 /* EMC_TFAW */
-				0x00000000 /* EMC_TRPAB */
-				0x00000004 /* EMC_TCLKSTABLE */
-				0x00000005 /* EMC_TCLKSTOP */
-				0x0000018e /* EMC_TREFBW */
-				0x00000006 /* EMC_QUSE_EXTRA */
-				0x00000004 /* EMC_FBIO_CFG6 */
-				0x00000000 /* EMC_ODT_WRITE */
-				0x00000000 /* EMC_ODT_READ */
-				0x00004288 /* EMC_FBIO_CFG5 */
-				0x007800a4 /* EMC_CFG_DIG_DLL */
-				0x00008000 /* EMC_CFG_DIG_DLL_PERIOD */
-				0x000fc000 /* EMC_DLL_XFORM_DQS0 */
-				0x000fc000 /* EMC_DLL_XFORM_DQS1 */
-				0x000fc000 /* EMC_DLL_XFORM_DQS2 */
-				0x000fc000 /* EMC_DLL_XFORM_DQS3 */
-				0x000fc000 /* EMC_DLL_XFORM_DQS4 */
-				0x000fc000 /* EMC_DLL_XFORM_DQS5 */
-				0x000fc000 /* EMC_DLL_XFORM_DQS6 */
-				0x000fc000 /* EMC_DLL_XFORM_DQS7 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE0 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE1 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE2 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE3 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE4 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE5 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE6 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE7 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS0 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS1 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS2 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS3 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS4 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS5 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS6 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS7 */
-				0x000fc000 /* EMC_DLL_XFORM_DQ0 */
-				0x000fc000 /* EMC_DLL_XFORM_DQ1 */
-				0x000fc000 /* EMC_DLL_XFORM_DQ2 */
-				0x000fc000 /* EMC_DLL_XFORM_DQ3 */
-				0x000002a0 /* EMC_XM2CMDPADCTRL */
-				0x0800211c /* EMC_XM2DQSPADCTRL2 */
-				0x00000000 /* EMC_XM2DQPADCTRL2 */
-				0x77fff884 /* EMC_XM2CLKPADCTRL */
-				0x01f1f108 /* EMC_XM2COMPPADCTRL */
-				0x05057404 /* EMC_XM2VTTGENPADCTRL */
-				0x54000007 /* EMC_XM2VTTGENPADCTRL2 */
-				0x08000168 /* EMC_XM2QUSEPADCTRL */
-				0x08000000 /* EMC_XM2DQSPADCTRL3 */
-				0x00000802 /* EMC_CTT_TERM_CTRL */
-				0x00000000 /* EMC_ZCAL_INTERVAL */
-				0x00000040 /* EMC_ZCAL_WAIT_CNT */
-				0x000c000c /* EMC_MRS_WAIT_CNT */
-				0xa0f10000 /* EMC_AUTO_CAL_CONFIG */
-				0x00000000 /* EMC_CTT */
-				0x00000000 /* EMC_CTT_DURATION */
-				0x8000040b /* EMC_DYN_SELF_REF_CONTROL */
-				0xe8000000 /* EMC_FBIO_SPARE */
-				0xff00ff00 /* EMC_CFG_RSV */
-			>;
-		};
-		timing-102000000 {
-			clock-frequency = <102000000>;
-			nvidia,emc-auto-cal-interval = <0x001fffff>;
-			nvidia,emc-mode-1 = <0x80100003>;
-			nvidia,emc-mode-2 = <0x80200008>;
-			nvidia,emc-mode-reset = <0x80001221>;
-			nvidia,emc-zcal-cnt-long = <0x00000040>;
-			nvidia,emc-cfg-periodic-qrst;
-			nvidia,emc-cfg-dyn-self-ref;
-			nvidia,emc-configuration = <
-				0x00000004 /* EMC_RC */
-				0x0000001a /* EMC_RFC */
-				0x00000003 /* EMC_RAS */
-				0x00000001 /* EMC_RP */
-				0x00000002 /* EMC_R2W */
-				0x0000000a /* EMC_W2R */
-				0x00000005 /* EMC_R2P */
-				0x0000000b /* EMC_W2P */
-				0x00000001 /* EMC_RD_RCD */
-				0x00000001 /* EMC_WR_RCD */
-				0x00000003 /* EMC_RRD */
-				0x00000001 /* EMC_REXT */
-				0x00000000 /* EMC_WEXT */
-				0x00000005 /* EMC_WDV */
-				0x00000005 /* EMC_QUSE */
-				0x00000004 /* EMC_QRST */
-				0x0000000a /* EMC_QSAFE */
-				0x0000000b /* EMC_RDV */
-				0x00000303 /* EMC_REFRESH */
-				0x00000000 /* EMC_BURST_REFRESH_NUM */
-				0x000000c0 /* EMC_PRE_REFRESH_REQ_CNT */
-				0x00000002 /* EMC_PDEX2WR */
-				0x00000002 /* EMC_PDEX2RD */
-				0x00000001 /* EMC_PCHG2PDEN */
-				0x00000000 /* EMC_ACT2PDEN */
-				0x00000007 /* EMC_AR2PDEN */
-				0x0000000f /* EMC_RW2PDEN */
-				0x0000001c /* EMC_TXSR */
-				0x0000001c /* EMC_TXSRDLL */
-				0x00000004 /* EMC_TCKE */
-				0x00000005 /* EMC_TFAW */
-				0x00000000 /* EMC_TRPAB */
-				0x00000004 /* EMC_TCLKSTABLE */
-				0x00000005 /* EMC_TCLKSTOP */
-				0x0000031c /* EMC_TREFBW */
-				0x00000006 /* EMC_QUSE_EXTRA */
-				0x00000004 /* EMC_FBIO_CFG6 */
-				0x00000000 /* EMC_ODT_WRITE */
-				0x00000000 /* EMC_ODT_READ */
-				0x00004288 /* EMC_FBIO_CFG5 */
-				0x007800a4 /* EMC_CFG_DIG_DLL */
-				0x00008000 /* EMC_CFG_DIG_DLL_PERIOD */
-				0x000fc000 /* EMC_DLL_XFORM_DQS0 */
-				0x000fc000 /* EMC_DLL_XFORM_DQS1 */
-				0x000fc000 /* EMC_DLL_XFORM_DQS2 */
-				0x000fc000 /* EMC_DLL_XFORM_DQS3 */
-				0x000fc000 /* EMC_DLL_XFORM_DQS4 */
-				0x000fc000 /* EMC_DLL_XFORM_DQS5 */
-				0x000fc000 /* EMC_DLL_XFORM_DQS6 */
-				0x000fc000 /* EMC_DLL_XFORM_DQS7 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE0 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE1 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE2 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE3 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE4 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE5 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE6 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE7 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS0 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS1 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS2 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS3 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS4 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS5 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS6 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS7 */
-				0x000fc000 /* EMC_DLL_XFORM_DQ0 */
-				0x000fc000 /* EMC_DLL_XFORM_DQ1 */
-				0x000fc000 /* EMC_DLL_XFORM_DQ2 */
-				0x000fc000 /* EMC_DLL_XFORM_DQ3 */
-				0x000002a0 /* EMC_XM2CMDPADCTRL */
-				0x0800211c /* EMC_XM2DQSPADCTRL2 */
-				0x00000000 /* EMC_XM2DQPADCTRL2 */
-				0x77fff884 /* EMC_XM2CLKPADCTRL */
-				0x01f1f108 /* EMC_XM2COMPPADCTRL */
-				0x05057404 /* EMC_XM2VTTGENPADCTRL */
-				0x54000007 /* EMC_XM2VTTGENPADCTRL2 */
-				0x08000168 /* EMC_XM2QUSEPADCTRL */
-				0x08000000 /* EMC_XM2DQSPADCTRL3 */
-				0x00000802 /* EMC_CTT_TERM_CTRL */
-				0x00000000 /* EMC_ZCAL_INTERVAL */
-				0x00000040 /* EMC_ZCAL_WAIT_CNT */
-				0x000c000c /* EMC_MRS_WAIT_CNT */
-				0xa0f10000 /* EMC_AUTO_CAL_CONFIG */
-				0x00000000 /* EMC_CTT */
-				0x00000000 /* EMC_CTT_DURATION */
-				0x80000713 /* EMC_DYN_SELF_REF_CONTROL */
-				0xe8000000 /* EMC_FBIO_SPARE */
-				0xff00ff00 /* EMC_CFG_RSV */
-			>;
-		};
-		timing-204000000 {
-			clock-frequency = <204000000>;
-			nvidia,emc-auto-cal-interval = <0x001fffff>;
-			nvidia,emc-mode-1 = <0x80100003>;
-			nvidia,emc-mode-2 = <0x80200008>;
-			nvidia,emc-mode-reset = <0x80001221>;
-			nvidia,emc-zcal-cnt-long = <0x00000040>;
-			nvidia,emc-cfg-periodic-qrst;
-			nvidia,emc-cfg-dyn-self-ref;
-			nvidia,emc-configuration = <
-				0x00000009 /* EMC_RC */
-				0x00000035 /* EMC_RFC */
-				0x00000007 /* EMC_RAS */
-				0x00000002 /* EMC_RP */
-				0x00000002 /* EMC_R2W */
-				0x0000000a /* EMC_W2R */
-				0x00000005 /* EMC_R2P */
-				0x0000000b /* EMC_W2P */
-				0x00000002 /* EMC_RD_RCD */
-				0x00000002 /* EMC_WR_RCD */
-				0x00000003 /* EMC_RRD */
-				0x00000001 /* EMC_REXT */
-				0x00000000 /* EMC_WEXT */
-				0x00000005 /* EMC_WDV */
-				0x00000005 /* EMC_QUSE */
-				0x00000004 /* EMC_QRST */
-				0x0000000a /* EMC_QSAFE */
-				0x0000000b /* EMC_RDV */
-				0x00000607 /* EMC_REFRESH */
-				0x00000000 /* EMC_BURST_REFRESH_NUM */
-				0x00000181 /* EMC_PRE_REFRESH_REQ_CNT */
-				0x00000002 /* EMC_PDEX2WR */
-				0x00000002 /* EMC_PDEX2RD */
-				0x00000001 /* EMC_PCHG2PDEN */
-				0x00000000 /* EMC_ACT2PDEN */
-				0x00000007 /* EMC_AR2PDEN */
-				0x0000000f /* EMC_RW2PDEN */
-				0x00000038 /* EMC_TXSR */
-				0x00000038 /* EMC_TXSRDLL */
-				0x00000004 /* EMC_TCKE */
-				0x00000009 /* EMC_TFAW */
-				0x00000000 /* EMC_TRPAB */
-				0x00000004 /* EMC_TCLKSTABLE */
-				0x00000005 /* EMC_TCLKSTOP */
-				0x00000638 /* EMC_TREFBW */
-				0x00000006 /* EMC_QUSE_EXTRA */
-				0x00000006 /* EMC_FBIO_CFG6 */
-				0x00000000 /* EMC_ODT_WRITE */
-				0x00000000 /* EMC_ODT_READ */
-				0x00004288 /* EMC_FBIO_CFG5 */
-				0x004400a4 /* EMC_CFG_DIG_DLL */
-				0x00008000 /* EMC_CFG_DIG_DLL_PERIOD */
-				0x00080000 /* EMC_DLL_XFORM_DQS0 */
-				0x00080000 /* EMC_DLL_XFORM_DQS1 */
-				0x00080000 /* EMC_DLL_XFORM_DQS2 */
-				0x00080000 /* EMC_DLL_XFORM_DQS3 */
-				0x00080000 /* EMC_DLL_XFORM_DQS4 */
-				0x00080000 /* EMC_DLL_XFORM_DQS5 */
-				0x00080000 /* EMC_DLL_XFORM_DQS6 */
-				0x00080000 /* EMC_DLL_XFORM_DQS7 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE0 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE1 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE2 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE3 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE4 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE5 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE6 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE7 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS0 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS1 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS2 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS3 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS4 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS5 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS6 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS7 */
-				0x00080000 /* EMC_DLL_XFORM_DQ0 */
-				0x00080000 /* EMC_DLL_XFORM_DQ1 */
-				0x00080000 /* EMC_DLL_XFORM_DQ2 */
-				0x00080000 /* EMC_DLL_XFORM_DQ3 */
-				0x000002a0 /* EMC_XM2CMDPADCTRL */
-				0x0800211c /* EMC_XM2DQSPADCTRL2 */
-				0x00000000 /* EMC_XM2DQPADCTRL2 */
-				0x77fff884 /* EMC_XM2CLKPADCTRL */
-				0x01f1f108 /* EMC_XM2COMPPADCTRL */
-				0x05057404 /* EMC_XM2VTTGENPADCTRL */
-				0x54000007 /* EMC_XM2VTTGENPADCTRL2 */
-				0x08000168 /* EMC_XM2QUSEPADCTRL */
-				0x08000000 /* EMC_XM2DQSPADCTRL3 */
-				0x00000802 /* EMC_CTT_TERM_CTRL */
-				0x00020000 /* EMC_ZCAL_INTERVAL */
-				0x00000100 /* EMC_ZCAL_WAIT_CNT */
-				0x000c000c /* EMC_MRS_WAIT_CNT */
-				0xa0f10000 /* EMC_AUTO_CAL_CONFIG */
-				0x00000000 /* EMC_CTT */
-				0x00000000 /* EMC_CTT_DURATION */
-				0x80000d22 /* EMC_DYN_SELF_REF_CONTROL */
-				0xe8000000 /* EMC_FBIO_SPARE */
-				0xff00ff00 /* EMC_CFG_RSV */
-			>;
-		};
-		timing-400000000 {
-			clock-frequency = <400000000>;
-			nvidia,emc-auto-cal-interval = <0x001fffff>;
-			nvidia,emc-mode-1 = <0x80100002>;
-			nvidia,emc-mode-2 = <0x80200000>;
-			nvidia,emc-mode-reset = <0x80000521>;
-			nvidia,emc-zcal-cnt-long = <0x00000040>;
-			nvidia,emc-configuration = <
-				0x00000012 /* EMC_RC */
-				0x00000066 /* EMC_RFC */
-				0x0000000c /* EMC_RAS */
-				0x00000004 /* EMC_RP */
-				0x00000003 /* EMC_R2W */
-				0x00000008 /* EMC_W2R */
-				0x00000002 /* EMC_R2P */
-				0x0000000a /* EMC_W2P */
-				0x00000004 /* EMC_RD_RCD */
-				0x00000004 /* EMC_WR_RCD */
-				0x00000002 /* EMC_RRD */
-				0x00000001 /* EMC_REXT */
-				0x00000000 /* EMC_WEXT */
-				0x00000004 /* EMC_WDV */
-				0x00000006 /* EMC_QUSE */
-				0x00000004 /* EMC_QRST */
-				0x0000000a /* EMC_QSAFE */
-				0x0000000c /* EMC_RDV */
-				0x00000bf0 /* EMC_REFRESH */
-				0x00000000 /* EMC_BURST_REFRESH_NUM */
-				0x000002fc /* EMC_PRE_REFRESH_REQ_CNT */
-				0x00000001 /* EMC_PDEX2WR */
-				0x00000008 /* EMC_PDEX2RD */
-				0x00000001 /* EMC_PCHG2PDEN */
-				0x00000000 /* EMC_ACT2PDEN */
-				0x00000008 /* EMC_AR2PDEN */
-				0x0000000f /* EMC_RW2PDEN */
-				0x0000006c /* EMC_TXSR */
-				0x00000200 /* EMC_TXSRDLL */
-				0x00000004 /* EMC_TCKE */
-				0x00000010 /* EMC_TFAW */
-				0x00000000 /* EMC_TRPAB */
-				0x00000004 /* EMC_TCLKSTABLE */
-				0x00000005 /* EMC_TCLKSTOP */
-				0x00000c30 /* EMC_TREFBW */
-				0x00000000 /* EMC_QUSE_EXTRA */
-				0x00000004 /* EMC_FBIO_CFG6 */
-				0x00000000 /* EMC_ODT_WRITE */
-				0x00000000 /* EMC_ODT_READ */
-				0x00007088 /* EMC_FBIO_CFG5 */
-				0x001d0084 /* EMC_CFG_DIG_DLL */
-				0x00008000 /* EMC_CFG_DIG_DLL_PERIOD */
-				0x0003c000 /* EMC_DLL_XFORM_DQS0 */
-				0x0003c000 /* EMC_DLL_XFORM_DQS1 */
-				0x0003c000 /* EMC_DLL_XFORM_DQS2 */
-				0x0003c000 /* EMC_DLL_XFORM_DQS3 */
-				0x0003c000 /* EMC_DLL_XFORM_DQS4 */
-				0x0003c000 /* EMC_DLL_XFORM_DQS5 */
-				0x0003c000 /* EMC_DLL_XFORM_DQS6 */
-				0x0003c000 /* EMC_DLL_XFORM_DQS7 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE0 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE1 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE2 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE3 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE4 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE5 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE6 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE7 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS0 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS1 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS2 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS3 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS4 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS5 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS6 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS7 */
-				0x00048000 /* EMC_DLL_XFORM_DQ0 */
-				0x00048000 /* EMC_DLL_XFORM_DQ1 */
-				0x00048000 /* EMC_DLL_XFORM_DQ2 */
-				0x00048000 /* EMC_DLL_XFORM_DQ3 */
-				0x000002a0 /* EMC_XM2CMDPADCTRL */
-				0x0800013d /* EMC_XM2DQSPADCTRL2 */
-				0x00000000 /* EMC_XM2DQPADCTRL2 */
-				0x77fff884 /* EMC_XM2CLKPADCTRL */
-				0x01f1f508 /* EMC_XM2COMPPADCTRL */
-				0x05057404 /* EMC_XM2VTTGENPADCTRL */
-				0x54000007 /* EMC_XM2VTTGENPADCTRL2 */
-				0x080001e8 /* EMC_XM2QUSEPADCTRL */
-				0x08000021 /* EMC_XM2DQSPADCTRL3 */
-				0x00000802 /* EMC_CTT_TERM_CTRL */
-				0x00020000 /* EMC_ZCAL_INTERVAL */
-				0x00000100 /* EMC_ZCAL_WAIT_CNT */
-				0x0158000c /* EMC_MRS_WAIT_CNT */
-				0xa0f10000 /* EMC_AUTO_CAL_CONFIG */
-				0x00000000 /* EMC_CTT */
-				0x00000000 /* EMC_CTT_DURATION */
-				0x800018c8 /* EMC_DYN_SELF_REF_CONTROL */
-				0xe8000000 /* EMC_FBIO_SPARE */
-				0xff00ff89 /* EMC_CFG_RSV */
-			>;
-		};
-		timing-800000000 {
-			clock-frequency = <800000000>;
-			nvidia,emc-auto-cal-interval = <0x001fffff>;
-			nvidia,emc-mode-1 = <0x80100002>;
-			nvidia,emc-mode-2 = <0x80200018>;
-			nvidia,emc-mode-reset = <0x80000d71>;
-			nvidia,emc-zcal-cnt-long = <0x00000040>;
-			nvidia,emc-cfg-periodic-qrst;
-			nvidia,emc-configuration = <
-				0x00000025 /* EMC_RC */
-				0x000000ce /* EMC_RFC */
-				0x0000001a /* EMC_RAS */
-				0x00000009 /* EMC_RP */
-				0x00000005 /* EMC_R2W */
-				0x0000000d /* EMC_W2R */
-				0x00000004 /* EMC_R2P */
-				0x00000013 /* EMC_W2P */
-				0x00000009 /* EMC_RD_RCD */
-				0x00000009 /* EMC_WR_RCD */
-				0x00000004 /* EMC_RRD */
-				0x00000001 /* EMC_REXT */
-				0x00000000 /* EMC_WEXT */
-				0x00000007 /* EMC_WDV */
-				0x0000000a /* EMC_QUSE */
-				0x00000009 /* EMC_QRST */
-				0x0000000b /* EMC_QSAFE */
-				0x00000011 /* EMC_RDV */
-				0x00001820 /* EMC_REFRESH */
-				0x00000000 /* EMC_BURST_REFRESH_NUM */
-				0x00000608 /* EMC_PRE_REFRESH_REQ_CNT */
-				0x00000003 /* EMC_PDEX2WR */
-				0x00000012 /* EMC_PDEX2RD */
-				0x00000001 /* EMC_PCHG2PDEN */
-				0x00000000 /* EMC_ACT2PDEN */
-				0x0000000f /* EMC_AR2PDEN */
-				0x00000018 /* EMC_RW2PDEN */
-				0x000000d8 /* EMC_TXSR */
-				0x00000200 /* EMC_TXSRDLL */
-				0x00000005 /* EMC_TCKE */
-				0x00000020 /* EMC_TFAW */
-				0x00000000 /* EMC_TRPAB */
-				0x00000007 /* EMC_TCLKSTABLE */
-				0x00000008 /* EMC_TCLKSTOP */
-				0x00001860 /* EMC_TREFBW */
-				0x0000000b /* EMC_QUSE_EXTRA */
-				0x00000006 /* EMC_FBIO_CFG6 */
-				0x00000000 /* EMC_ODT_WRITE */
-				0x00000000 /* EMC_ODT_READ */
-				0x00005088 /* EMC_FBIO_CFG5 */
-				0xf0070191 /* EMC_CFG_DIG_DLL */
-				0x00008000 /* EMC_CFG_DIG_DLL_PERIOD */
-				0x0000800a /* EMC_DLL_XFORM_DQS0 */
-				0x0000000a /* EMC_DLL_XFORM_DQS1 */
-				0x0000000a /* EMC_DLL_XFORM_DQS2 */
-				0x0000000a /* EMC_DLL_XFORM_DQS3 */
-				0x0000000a /* EMC_DLL_XFORM_DQS4 */
-				0x0000000a /* EMC_DLL_XFORM_DQS5 */
-				0x0000000a /* EMC_DLL_XFORM_DQS6 */
-				0x0000000a /* EMC_DLL_XFORM_DQS7 */
-				0x00018000 /* EMC_DLL_XFORM_QUSE0 */
-				0x00018000 /* EMC_DLL_XFORM_QUSE1 */
-				0x00018000 /* EMC_DLL_XFORM_QUSE2 */
-				0x00018000 /* EMC_DLL_XFORM_QUSE3 */
-				0x00018000 /* EMC_DLL_XFORM_QUSE4 */
-				0x00018000 /* EMC_DLL_XFORM_QUSE5 */
-				0x00018000 /* EMC_DLL_XFORM_QUSE6 */
-				0x00018000 /* EMC_DLL_XFORM_QUSE7 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS0 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS1 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS2 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS3 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS4 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS5 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS6 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS7 */
-				0x0000000a /* EMC_DLL_XFORM_DQ0 */
-				0x0000000a /* EMC_DLL_XFORM_DQ1 */
-				0x0000000a /* EMC_DLL_XFORM_DQ2 */
-				0x0000000a /* EMC_DLL_XFORM_DQ3 */
-				0x000002a0 /* EMC_XM2CMDPADCTRL */
-				0x0600013d /* EMC_XM2DQSPADCTRL2 */
-				0x22220000 /* EMC_XM2DQPADCTRL2 */
-				0x77fff884 /* EMC_XM2CLKPADCTRL */
-				0x01f1f501 /* EMC_XM2COMPPADCTRL */
-				0x07077404 /* EMC_XM2VTTGENPADCTRL */
-				0x54000000 /* EMC_XM2VTTGENPADCTRL2 */
-				0x080001e8 /* EMC_XM2QUSEPADCTRL */
-				0x08000021 /* EMC_XM2DQSPADCTRL3 */
-				0x00000802 /* EMC_CTT_TERM_CTRL */
-				0x00020000 /* EMC_ZCAL_INTERVAL */
-				0x00000100 /* EMC_ZCAL_WAIT_CNT */
-				0x00f0000c /* EMC_MRS_WAIT_CNT */
-				0xa0f10000 /* EMC_AUTO_CAL_CONFIG */
-				0x00000000 /* EMC_CTT */
-				0x00000000 /* EMC_CTT_DURATION */
-				0x8000308c /* EMC_DYN_SELF_REF_CONTROL */
-				0xe8000000 /* EMC_FBIO_SPARE */
-				0xff00ff49 /* EMC_CFG_RSV */
-			>;
-		};
-	};
-	emc-timings-1 {
-		nvidia,ram-code = <1>;  /* Hynix M RAM */
-		timing-25500000 {
-			clock-frequency = <25500000>;
-			nvidia,emc-auto-cal-interval = <0x001fffff>;
-			nvidia,emc-mode-1 = <0x80100003>;
-			nvidia,emc-mode-2 = <0x80200008>;
-			nvidia,emc-mode-reset = <0x80001221>;
-			nvidia,emc-zcal-cnt-long = <0x00000040>;
-			nvidia,emc-cfg-periodic-qrst;
-			nvidia,emc-cfg-dyn-self-ref;
-			nvidia,emc-configuration = <
-				0x00000001 /* EMC_RC */
-				0x00000006 /* EMC_RFC */
-				0x00000000 /* EMC_RAS */
-				0x00000000 /* EMC_RP */
-				0x00000002 /* EMC_R2W */
-				0x0000000a /* EMC_W2R */
-				0x00000005 /* EMC_R2P */
-				0x0000000b /* EMC_W2P */
-				0x00000000 /* EMC_RD_RCD */
-				0x00000000 /* EMC_WR_RCD */
-				0x00000003 /* EMC_RRD */
-				0x00000001 /* EMC_REXT */
-				0x00000000 /* EMC_WEXT */
-				0x00000005 /* EMC_WDV */
-				0x00000005 /* EMC_QUSE */
-				0x00000004 /* EMC_QRST */
-				0x0000000a /* EMC_QSAFE */
-				0x0000000b /* EMC_RDV */
-				0x000000c0 /* EMC_REFRESH */
-				0x00000000 /* EMC_BURST_REFRESH_NUM */
-				0x00000030 /* EMC_PRE_REFRESH_REQ_CNT */
-				0x00000002 /* EMC_PDEX2WR */
-				0x00000002 /* EMC_PDEX2RD */
-				0x00000001 /* EMC_PCHG2PDEN */
-				0x00000000 /* EMC_ACT2PDEN */
-				0x00000007 /* EMC_AR2PDEN */
-				0x0000000f /* EMC_RW2PDEN */
-				0x00000007 /* EMC_TXSR */
-				0x00000007 /* EMC_TXSRDLL */
-				0x00000004 /* EMC_TCKE */
-				0x00000002 /* EMC_TFAW */
-				0x00000000 /* EMC_TRPAB */
-				0x00000004 /* EMC_TCLKSTABLE */
-				0x00000005 /* EMC_TCLKSTOP */
-				0x000000c7 /* EMC_TREFBW */
-				0x00000006 /* EMC_QUSE_EXTRA */
-				0x00000004 /* EMC_FBIO_CFG6 */
-				0x00000000 /* EMC_ODT_WRITE */
-				0x00000000 /* EMC_ODT_READ */
-				0x00004288 /* EMC_FBIO_CFG5 */
-				0x007800a4 /* EMC_CFG_DIG_DLL */
-				0x00008000 /* EMC_CFG_DIG_DLL_PERIOD */
-				0x000fc000 /* EMC_DLL_XFORM_DQS0 */
-				0x000fc000 /* EMC_DLL_XFORM_DQS1 */
-				0x000fc000 /* EMC_DLL_XFORM_DQS2 */
-				0x000fc000 /* EMC_DLL_XFORM_DQS3 */
-				0x000fc000 /* EMC_DLL_XFORM_DQS4 */
-				0x000fc000 /* EMC_DLL_XFORM_DQS5 */
-				0x000fc000 /* EMC_DLL_XFORM_DQS6 */
-				0x000fc000 /* EMC_DLL_XFORM_DQS7 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE0 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE1 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE2 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE3 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE4 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE5 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE6 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE7 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS0 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS1 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS2 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS3 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS4 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS5 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS6 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS7 */
-				0x000fc000 /* EMC_DLL_XFORM_DQ0 */
-				0x000fc000 /* EMC_DLL_XFORM_DQ1 */
-				0x000fc000 /* EMC_DLL_XFORM_DQ2 */
-				0x000fc000 /* EMC_DLL_XFORM_DQ3 */
-				0x000002a0 /* EMC_XM2CMDPADCTRL */
-				0x0800211c /* EMC_XM2DQSPADCTRL2 */
-				0x00000000 /* EMC_XM2DQPADCTRL2 */
-				0x77fff884 /* EMC_XM2CLKPADCTRL */
-				0x01f1f108 /* EMC_XM2COMPPADCTRL */
-				0x05057404 /* EMC_XM2VTTGENPADCTRL */
-				0x54000007 /* EMC_XM2VTTGENPADCTRL2 */
-				0x08000168 /* EMC_XM2QUSEPADCTRL */
-				0x08000000 /* EMC_XM2DQSPADCTRL3 */
-				0x00000802 /* EMC_CTT_TERM_CTRL */
-				0x00000000 /* EMC_ZCAL_INTERVAL */
-				0x00000040 /* EMC_ZCAL_WAIT_CNT */
-				0x000c000c /* EMC_MRS_WAIT_CNT */
-				0xa0f10000 /* EMC_AUTO_CAL_CONFIG */
-				0x00000000 /* EMC_CTT */
-				0x00000000 /* EMC_CTT_DURATION */
-				0x80000287 /* EMC_DYN_SELF_REF_CONTROL */
-				0xe8000000 /* EMC_FBIO_SPARE */
-				0xff00ff00 /* EMC_CFG_RSV */
-			>;
-		};
-		timing-51000000 {
-			clock-frequency = <51000000>;
-			nvidia,emc-auto-cal-interval = <0x001fffff>;
-			nvidia,emc-mode-1 = <0x80100003>;
-			nvidia,emc-mode-2 = <0x80200008>;
-			nvidia,emc-mode-reset = <0x80001221>;
-			nvidia,emc-zcal-cnt-long = <0x00000040>;
-			nvidia,emc-cfg-periodic-qrst;
-			nvidia,emc-cfg-dyn-self-ref;
-			nvidia,emc-configuration = <
-				0x00000002 /* EMC_RC */
-				0x0000000d /* EMC_RFC */
-				0x00000001 /* EMC_RAS */
-				0x00000000 /* EMC_RP */
-				0x00000002 /* EMC_R2W */
-				0x0000000a /* EMC_W2R */
-				0x00000005 /* EMC_R2P */
-				0x0000000b /* EMC_W2P */
-				0x00000000 /* EMC_RD_RCD */
-				0x00000000 /* EMC_WR_RCD */
-				0x00000003 /* EMC_RRD */
-				0x00000001 /* EMC_REXT */
-				0x00000000 /* EMC_WEXT */
-				0x00000005 /* EMC_WDV */
-				0x00000005 /* EMC_QUSE */
-				0x00000004 /* EMC_QRST */
-				0x0000000a /* EMC_QSAFE */
-				0x0000000b /* EMC_RDV */
-				0x00000181 /* EMC_REFRESH */
-				0x00000000 /* EMC_BURST_REFRESH_NUM */
-				0x00000060 /* EMC_PRE_REFRESH_REQ_CNT */
-				0x00000002 /* EMC_PDEX2WR */
-				0x00000002 /* EMC_PDEX2RD */
-				0x00000001 /* EMC_PCHG2PDEN */
-				0x00000000 /* EMC_ACT2PDEN */
-				0x00000007 /* EMC_AR2PDEN */
-				0x0000000f /* EMC_RW2PDEN */
-				0x0000000e /* EMC_TXSR */
-				0x0000000e /* EMC_TXSRDLL */
-				0x00000004 /* EMC_TCKE */
-				0x00000003 /* EMC_TFAW */
-				0x00000000 /* EMC_TRPAB */
-				0x00000004 /* EMC_TCLKSTABLE */
-				0x00000005 /* EMC_TCLKSTOP */
-				0x0000018e /* EMC_TREFBW */
-				0x00000006 /* EMC_QUSE_EXTRA */
-				0x00000004 /* EMC_FBIO_CFG6 */
-				0x00000000 /* EMC_ODT_WRITE */
-				0x00000000 /* EMC_ODT_READ */
-				0x00004288 /* EMC_FBIO_CFG5 */
-				0x007800a4 /* EMC_CFG_DIG_DLL */
-				0x00008000 /* EMC_CFG_DIG_DLL_PERIOD */
-				0x000fc000 /* EMC_DLL_XFORM_DQS0 */
-				0x000fc000 /* EMC_DLL_XFORM_DQS1 */
-				0x000fc000 /* EMC_DLL_XFORM_DQS2 */
-				0x000fc000 /* EMC_DLL_XFORM_DQS3 */
-				0x000fc000 /* EMC_DLL_XFORM_DQS4 */
-				0x000fc000 /* EMC_DLL_XFORM_DQS5 */
-				0x000fc000 /* EMC_DLL_XFORM_DQS6 */
-				0x000fc000 /* EMC_DLL_XFORM_DQS7 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE0 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE1 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE2 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE3 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE4 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE5 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE6 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE7 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS0 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS1 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS2 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS3 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS4 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS5 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS6 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS7 */
-				0x000fc000 /* EMC_DLL_XFORM_DQ0 */
-				0x000fc000 /* EMC_DLL_XFORM_DQ1 */
-				0x000fc000 /* EMC_DLL_XFORM_DQ2 */
-				0x000fc000 /* EMC_DLL_XFORM_DQ3 */
-				0x000002a0 /* EMC_XM2CMDPADCTRL */
-				0x0800211c /* EMC_XM2DQSPADCTRL2 */
-				0x00000000 /* EMC_XM2DQPADCTRL2 */
-				0x77fff884 /* EMC_XM2CLKPADCTRL */
-				0x01f1f108 /* EMC_XM2COMPPADCTRL */
-				0x05057404 /* EMC_XM2VTTGENPADCTRL */
-				0x54000007 /* EMC_XM2VTTGENPADCTRL2 */
-				0x08000168 /* EMC_XM2QUSEPADCTRL */
-				0x08000000 /* EMC_XM2DQSPADCTRL3 */
-				0x00000802 /* EMC_CTT_TERM_CTRL */
-				0x00000000 /* EMC_ZCAL_INTERVAL */
-				0x00000040 /* EMC_ZCAL_WAIT_CNT */
-				0x000c000c /* EMC_MRS_WAIT_CNT */
-				0xa0f10000 /* EMC_AUTO_CAL_CONFIG */
-				0x00000000 /* EMC_CTT */
-				0x00000000 /* EMC_CTT_DURATION */
-				0x8000040b /* EMC_DYN_SELF_REF_CONTROL */
-				0xe8000000 /* EMC_FBIO_SPARE */
-				0xff00ff00 /* EMC_CFG_RSV */
-			>;
-		};
-		timing-102000000 {
-			clock-frequency = <102000000>;
-			nvidia,emc-auto-cal-interval = <0x001fffff>;
-			nvidia,emc-mode-1 = <0x80100003>;
-			nvidia,emc-mode-2 = <0x80200008>;
-			nvidia,emc-mode-reset = <0x80001221>;
-			nvidia,emc-zcal-cnt-long = <0x00000040>;
-			nvidia,emc-cfg-periodic-qrst;
-			nvidia,emc-cfg-dyn-self-ref;
-			nvidia,emc-configuration = <
-				0x00000004 /* EMC_RC */
-				0x0000001a /* EMC_RFC */
-				0x00000003 /* EMC_RAS */
-				0x00000001 /* EMC_RP */
-				0x00000002 /* EMC_R2W */
-				0x0000000a /* EMC_W2R */
-				0x00000005 /* EMC_R2P */
-				0x0000000b /* EMC_W2P */
-				0x00000001 /* EMC_RD_RCD */
-				0x00000001 /* EMC_WR_RCD */
-				0x00000003 /* EMC_RRD */
-				0x00000001 /* EMC_REXT */
-				0x00000000 /* EMC_WEXT */
-				0x00000005 /* EMC_WDV */
-				0x00000005 /* EMC_QUSE */
-				0x00000004 /* EMC_QRST */
-				0x0000000a /* EMC_QSAFE */
-				0x0000000b /* EMC_RDV */
-				0x00000303 /* EMC_REFRESH */
-				0x00000000 /* EMC_BURST_REFRESH_NUM */
-				0x000000c0 /* EMC_PRE_REFRESH_REQ_CNT */
-				0x00000002 /* EMC_PDEX2WR */
-				0x00000002 /* EMC_PDEX2RD */
-				0x00000001 /* EMC_PCHG2PDEN */
-				0x00000000 /* EMC_ACT2PDEN */
-				0x00000007 /* EMC_AR2PDEN */
-				0x0000000f /* EMC_RW2PDEN */
-				0x0000001c /* EMC_TXSR */
-				0x0000001c /* EMC_TXSRDLL */
-				0x00000004 /* EMC_TCKE */
-				0x00000005 /* EMC_TFAW */
-				0x00000000 /* EMC_TRPAB */
-				0x00000004 /* EMC_TCLKSTABLE */
-				0x00000005 /* EMC_TCLKSTOP */
-				0x0000031c /* EMC_TREFBW */
-				0x00000006 /* EMC_QUSE_EXTRA */
-				0x00000004 /* EMC_FBIO_CFG6 */
-				0x00000000 /* EMC_ODT_WRITE */
-				0x00000000 /* EMC_ODT_READ */
-				0x00004288 /* EMC_FBIO_CFG5 */
-				0x007800a4 /* EMC_CFG_DIG_DLL */
-				0x00008000 /* EMC_CFG_DIG_DLL_PERIOD */
-				0x000fc000 /* EMC_DLL_XFORM_DQS0 */
-				0x000fc000 /* EMC_DLL_XFORM_DQS1 */
-				0x000fc000 /* EMC_DLL_XFORM_DQS2 */
-				0x000fc000 /* EMC_DLL_XFORM_DQS3 */
-				0x000fc000 /* EMC_DLL_XFORM_DQS4 */
-				0x000fc000 /* EMC_DLL_XFORM_DQS5 */
-				0x000fc000 /* EMC_DLL_XFORM_DQS6 */
-				0x000fc000 /* EMC_DLL_XFORM_DQS7 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE0 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE1 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE2 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE3 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE4 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE5 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE6 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE7 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS0 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS1 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS2 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS3 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS4 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS5 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS6 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS7 */
-				0x000fc000 /* EMC_DLL_XFORM_DQ0 */
-				0x000fc000 /* EMC_DLL_XFORM_DQ1 */
-				0x000fc000 /* EMC_DLL_XFORM_DQ2 */
-				0x000fc000 /* EMC_DLL_XFORM_DQ3 */
-				0x000002a0 /* EMC_XM2CMDPADCTRL */
-				0x0800211c /* EMC_XM2DQSPADCTRL2 */
-				0x00000000 /* EMC_XM2DQPADCTRL2 */
-				0x77fff884 /* EMC_XM2CLKPADCTRL */
-				0x01f1f108 /* EMC_XM2COMPPADCTRL */
-				0x05057404 /* EMC_XM2VTTGENPADCTRL */
-				0x54000007 /* EMC_XM2VTTGENPADCTRL2 */
-				0x08000168 /* EMC_XM2QUSEPADCTRL */
-				0x08000000 /* EMC_XM2DQSPADCTRL3 */
-				0x00000802 /* EMC_CTT_TERM_CTRL */
-				0x00000000 /* EMC_ZCAL_INTERVAL */
-				0x00000040 /* EMC_ZCAL_WAIT_CNT */
-				0x000c000c /* EMC_MRS_WAIT_CNT */
-				0xa0f10000 /* EMC_AUTO_CAL_CONFIG */
-				0x00000000 /* EMC_CTT */
-				0x00000000 /* EMC_CTT_DURATION */
-				0x80000713 /* EMC_DYN_SELF_REF_CONTROL */
-				0xe8000000 /* EMC_FBIO_SPARE */
-				0xff00ff00 /* EMC_CFG_RSV */
-			>;
-		};
-		timing-204000000 {
-			clock-frequency = <204000000>;
-			nvidia,emc-auto-cal-interval = <0x001fffff>;
-			nvidia,emc-mode-1 = <0x80100003>;
-			nvidia,emc-mode-2 = <0x80200008>;
-			nvidia,emc-mode-reset = <0x80001221>;
-			nvidia,emc-zcal-cnt-long = <0x00000040>;
-			nvidia,emc-cfg-periodic-qrst;
-			nvidia,emc-cfg-dyn-self-ref;
-			nvidia,emc-configuration = <
-				0x00000009 /* EMC_RC */
-				0x00000035 /* EMC_RFC */
-				0x00000007 /* EMC_RAS */
-				0x00000002 /* EMC_RP */
-				0x00000002 /* EMC_R2W */
-				0x0000000a /* EMC_W2R */
-				0x00000005 /* EMC_R2P */
-				0x0000000b /* EMC_W2P */
-				0x00000002 /* EMC_RD_RCD */
-				0x00000002 /* EMC_WR_RCD */
-				0x00000003 /* EMC_RRD */
-				0x00000001 /* EMC_REXT */
-				0x00000000 /* EMC_WEXT */
-				0x00000005 /* EMC_WDV */
-				0x00000005 /* EMC_QUSE */
-				0x00000004 /* EMC_QRST */
-				0x0000000a /* EMC_QSAFE */
-				0x0000000b /* EMC_RDV */
-				0x00000607 /* EMC_REFRESH */
-				0x00000000 /* EMC_BURST_REFRESH_NUM */
-				0x00000181 /* EMC_PRE_REFRESH_REQ_CNT */
-				0x00000002 /* EMC_PDEX2WR */
-				0x00000002 /* EMC_PDEX2RD */
-				0x00000001 /* EMC_PCHG2PDEN */
-				0x00000000 /* EMC_ACT2PDEN */
-				0x00000007 /* EMC_AR2PDEN */
-				0x0000000f /* EMC_RW2PDEN */
-				0x00000038 /* EMC_TXSR */
-				0x00000038 /* EMC_TXSRDLL */
-				0x00000004 /* EMC_TCKE */
-				0x00000009 /* EMC_TFAW */
-				0x00000000 /* EMC_TRPAB */
-				0x00000004 /* EMC_TCLKSTABLE */
-				0x00000005 /* EMC_TCLKSTOP */
-				0x00000638 /* EMC_TREFBW */
-				0x00000006 /* EMC_QUSE_EXTRA */
-				0x00000006 /* EMC_FBIO_CFG6 */
-				0x00000000 /* EMC_ODT_WRITE */
-				0x00000000 /* EMC_ODT_READ */
-				0x00004288 /* EMC_FBIO_CFG5 */
-				0x004400a4 /* EMC_CFG_DIG_DLL */
-				0x00008000 /* EMC_CFG_DIG_DLL_PERIOD */
-				0x00080000 /* EMC_DLL_XFORM_DQS0 */
-				0x00080000 /* EMC_DLL_XFORM_DQS1 */
-				0x00080000 /* EMC_DLL_XFORM_DQS2 */
-				0x00080000 /* EMC_DLL_XFORM_DQS3 */
-				0x00080000 /* EMC_DLL_XFORM_DQS4 */
-				0x00080000 /* EMC_DLL_XFORM_DQS5 */
-				0x00080000 /* EMC_DLL_XFORM_DQS6 */
-				0x00080000 /* EMC_DLL_XFORM_DQS7 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE0 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE1 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE2 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE3 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE4 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE5 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE6 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE7 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS0 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS1 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS2 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS3 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS4 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS5 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS6 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS7 */
-				0x00080000 /* EMC_DLL_XFORM_DQ0 */
-				0x00080000 /* EMC_DLL_XFORM_DQ1 */
-				0x00080000 /* EMC_DLL_XFORM_DQ2 */
-				0x00080000 /* EMC_DLL_XFORM_DQ3 */
-				0x000002a0 /* EMC_XM2CMDPADCTRL */
-				0x0800211c /* EMC_XM2DQSPADCTRL2 */
-				0x00000000 /* EMC_XM2DQPADCTRL2 */
-				0x77fff884 /* EMC_XM2CLKPADCTRL */
-				0x01f1f108 /* EMC_XM2COMPPADCTRL */
-				0x05057404 /* EMC_XM2VTTGENPADCTRL */
-				0x54000007 /* EMC_XM2VTTGENPADCTRL2 */
-				0x08000168 /* EMC_XM2QUSEPADCTRL */
-				0x08000000 /* EMC_XM2DQSPADCTRL3 */
-				0x00000802 /* EMC_CTT_TERM_CTRL */
-				0x00020000 /* EMC_ZCAL_INTERVAL */
-				0x00000100 /* EMC_ZCAL_WAIT_CNT */
-				0x000c000c /* EMC_MRS_WAIT_CNT */
-				0xa0f10000 /* EMC_AUTO_CAL_CONFIG */
-				0x00000000 /* EMC_CTT */
-				0x00000000 /* EMC_CTT_DURATION */
-				0x80000d22 /* EMC_DYN_SELF_REF_CONTROL */
-				0xe8000000 /* EMC_FBIO_SPARE */
-				0xff00ff00 /* EMC_CFG_RSV */
-			>;
-		};
-		timing-400000000 {
-			clock-frequency = <400000000>;
-			nvidia,emc-auto-cal-interval = <0x001fffff>;
-			nvidia,emc-mode-1 = <0x80100002>;
-			nvidia,emc-mode-2 = <0x80200000>;
-			nvidia,emc-mode-reset = <0x80000521>;
-			nvidia,emc-zcal-cnt-long = <0x00000040>;
-			nvidia,emc-configuration = <
-				0x00000012 /* EMC_RC */
-				0x00000066 /* EMC_RFC */
-				0x0000000c /* EMC_RAS */
-				0x00000004 /* EMC_RP */
-				0x00000003 /* EMC_R2W */
-				0x00000008 /* EMC_W2R */
-				0x00000002 /* EMC_R2P */
-				0x0000000a /* EMC_W2P */
-				0x00000004 /* EMC_RD_RCD */
-				0x00000004 /* EMC_WR_RCD */
-				0x00000002 /* EMC_RRD */
-				0x00000001 /* EMC_REXT */
-				0x00000000 /* EMC_WEXT */
-				0x00000004 /* EMC_WDV */
-				0x00000006 /* EMC_QUSE */
-				0x00000004 /* EMC_QRST */
-				0x0000000a /* EMC_QSAFE */
-				0x0000000c /* EMC_RDV */
-				0x00000bf0 /* EMC_REFRESH */
-				0x00000000 /* EMC_BURST_REFRESH_NUM */
-				0x000002fc /* EMC_PRE_REFRESH_REQ_CNT */
-				0x00000001 /* EMC_PDEX2WR */
-				0x00000008 /* EMC_PDEX2RD */
-				0x00000001 /* EMC_PCHG2PDEN */
-				0x00000000 /* EMC_ACT2PDEN */
-				0x00000008 /* EMC_AR2PDEN */
-				0x0000000f /* EMC_RW2PDEN */
-				0x0000006c /* EMC_TXSR */
-				0x00000200 /* EMC_TXSRDLL */
-				0x00000004 /* EMC_TCKE */
-				0x00000010 /* EMC_TFAW */
-				0x00000000 /* EMC_TRPAB */
-				0x00000004 /* EMC_TCLKSTABLE */
-				0x00000005 /* EMC_TCLKSTOP */
-				0x00000c30 /* EMC_TREFBW */
-				0x00000000 /* EMC_QUSE_EXTRA */
-				0x00000004 /* EMC_FBIO_CFG6 */
-				0x00000000 /* EMC_ODT_WRITE */
-				0x00000000 /* EMC_ODT_READ */
-				0x00007088 /* EMC_FBIO_CFG5 */
-				0x001d0084 /* EMC_CFG_DIG_DLL */
-				0x00008000 /* EMC_CFG_DIG_DLL_PERIOD */
-				0x0003c000 /* EMC_DLL_XFORM_DQS0 */
-				0x0003c000 /* EMC_DLL_XFORM_DQS1 */
-				0x0003c000 /* EMC_DLL_XFORM_DQS2 */
-				0x0003c000 /* EMC_DLL_XFORM_DQS3 */
-				0x0003c000 /* EMC_DLL_XFORM_DQS4 */
-				0x0003c000 /* EMC_DLL_XFORM_DQS5 */
-				0x0003c000 /* EMC_DLL_XFORM_DQS6 */
-				0x0003c000 /* EMC_DLL_XFORM_DQS7 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE0 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE1 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE2 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE3 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE4 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE5 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE6 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE7 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS0 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS1 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS2 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS3 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS4 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS5 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS6 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS7 */
-				0x00048000 /* EMC_DLL_XFORM_DQ0 */
-				0x00048000 /* EMC_DLL_XFORM_DQ1 */
-				0x00048000 /* EMC_DLL_XFORM_DQ2 */
-				0x00048000 /* EMC_DLL_XFORM_DQ3 */
-				0x000002a0 /* EMC_XM2CMDPADCTRL */
-				0x0800013d /* EMC_XM2DQSPADCTRL2 */
-				0x00000000 /* EMC_XM2DQPADCTRL2 */
-				0x77fff884 /* EMC_XM2CLKPADCTRL */
-				0x01f1f508 /* EMC_XM2COMPPADCTRL */
-				0x05057404 /* EMC_XM2VTTGENPADCTRL */
-				0x54000007 /* EMC_XM2VTTGENPADCTRL2 */
-				0x080001e8 /* EMC_XM2QUSEPADCTRL */
-				0x08000021 /* EMC_XM2DQSPADCTRL3 */
-				0x00000802 /* EMC_CTT_TERM_CTRL */
-				0x00020000 /* EMC_ZCAL_INTERVAL */
-				0x00000100 /* EMC_ZCAL_WAIT_CNT */
-				0x0158000c /* EMC_MRS_WAIT_CNT */
-				0xa0f10000 /* EMC_AUTO_CAL_CONFIG */
-				0x00000000 /* EMC_CTT */
-				0x00000000 /* EMC_CTT_DURATION */
-				0x800018c8 /* EMC_DYN_SELF_REF_CONTROL */
-				0xe8000000 /* EMC_FBIO_SPARE */
-				0xff00ff89 /* EMC_CFG_RSV */
-			>;
-		};
-		timing-800000000 {
-			clock-frequency = <800000000>;
-			nvidia,emc-auto-cal-interval = <0x001fffff>;
-			nvidia,emc-mode-1 = <0x80100002>;
-			nvidia,emc-mode-2 = <0x80200018>;
-			nvidia,emc-mode-reset = <0x80000d71>;
-			nvidia,emc-zcal-cnt-long = <0x00000040>;
-			nvidia,emc-cfg-periodic-qrst;
-			nvidia,emc-configuration = <
-				0x00000025 /* EMC_RC */
-				0x000000ce /* EMC_RFC */
-				0x0000001a /* EMC_RAS */
-				0x00000009 /* EMC_RP */
-				0x00000005 /* EMC_R2W */
-				0x0000000d /* EMC_W2R */
-				0x00000004 /* EMC_R2P */
-				0x00000013 /* EMC_W2P */
-				0x00000009 /* EMC_RD_RCD */
-				0x00000009 /* EMC_WR_RCD */
-				0x00000004 /* EMC_RRD */
-				0x00000001 /* EMC_REXT */
-				0x00000000 /* EMC_WEXT */
-				0x00000007 /* EMC_WDV */
-				0x0000000a /* EMC_QUSE */
-				0x00000009 /* EMC_QRST */
-				0x0000000b /* EMC_QSAFE */
-				0x00000011 /* EMC_RDV */
-				0x00001820 /* EMC_REFRESH */
-				0x00000000 /* EMC_BURST_REFRESH_NUM */
-				0x00000608 /* EMC_PRE_REFRESH_REQ_CNT */
-				0x00000003 /* EMC_PDEX2WR */
-				0x00000012 /* EMC_PDEX2RD */
-				0x00000001 /* EMC_PCHG2PDEN */
-				0x00000000 /* EMC_ACT2PDEN */
-				0x0000000f /* EMC_AR2PDEN */
-				0x00000018 /* EMC_RW2PDEN */
-				0x000000d8 /* EMC_TXSR */
-				0x00000200 /* EMC_TXSRDLL */
-				0x00000005 /* EMC_TCKE */
-				0x00000020 /* EMC_TFAW */
-				0x00000000 /* EMC_TRPAB */
-				0x00000007 /* EMC_TCLKSTABLE */
-				0x00000008 /* EMC_TCLKSTOP */
-				0x00001860 /* EMC_TREFBW */
-				0x0000000b /* EMC_QUSE_EXTRA */
-				0x00000006 /* EMC_FBIO_CFG6 */
-				0x00000000 /* EMC_ODT_WRITE */
-				0x00000000 /* EMC_ODT_READ */
-				0x00005088 /* EMC_FBIO_CFG5 */
-				0xf0070191 /* EMC_CFG_DIG_DLL */
-				0x00008000 /* EMC_CFG_DIG_DLL_PERIOD */
-				0x0000800a /* EMC_DLL_XFORM_DQS0 */
-				0x0000000a /* EMC_DLL_XFORM_DQS1 */
-				0x0000000a /* EMC_DLL_XFORM_DQS2 */
-				0x0000000a /* EMC_DLL_XFORM_DQS3 */
-				0x0000000a /* EMC_DLL_XFORM_DQS4 */
-				0x0000000a /* EMC_DLL_XFORM_DQS5 */
-				0x0000000a /* EMC_DLL_XFORM_DQS6 */
-				0x0000000a /* EMC_DLL_XFORM_DQS7 */
-				0x00018000 /* EMC_DLL_XFORM_QUSE0 */
-				0x00018000 /* EMC_DLL_XFORM_QUSE1 */
-				0x00018000 /* EMC_DLL_XFORM_QUSE2 */
-				0x00018000 /* EMC_DLL_XFORM_QUSE3 */
-				0x00018000 /* EMC_DLL_XFORM_QUSE4 */
-				0x00018000 /* EMC_DLL_XFORM_QUSE5 */
-				0x00018000 /* EMC_DLL_XFORM_QUSE6 */
-				0x00018000 /* EMC_DLL_XFORM_QUSE7 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS0 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS1 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS2 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS3 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS4 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS5 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS6 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS7 */
-				0x0000000a /* EMC_DLL_XFORM_DQ0 */
-				0x0000000a /* EMC_DLL_XFORM_DQ1 */
-				0x0000000a /* EMC_DLL_XFORM_DQ2 */
-				0x0000000a /* EMC_DLL_XFORM_DQ3 */
-				0x000002a0 /* EMC_XM2CMDPADCTRL */
-				0x0600013d /* EMC_XM2DQSPADCTRL2 */
-				0x22220000 /* EMC_XM2DQPADCTRL2 */
-				0x77fff884 /* EMC_XM2CLKPADCTRL */
-				0x01f1f501 /* EMC_XM2COMPPADCTRL */
-				0x07077404 /* EMC_XM2VTTGENPADCTRL */
-				0x54000000 /* EMC_XM2VTTGENPADCTRL2 */
-				0x080001e8 /* EMC_XM2QUSEPADCTRL */
-				0x08000021 /* EMC_XM2DQSPADCTRL3 */
-				0x00000802 /* EMC_CTT_TERM_CTRL */
-				0x00020000 /* EMC_ZCAL_INTERVAL */
-				0x00000100 /* EMC_ZCAL_WAIT_CNT */
-				0x00f0000c /* EMC_MRS_WAIT_CNT */
-				0xa0f10000 /* EMC_AUTO_CAL_CONFIG */
-				0x00000000 /* EMC_CTT */
-				0x00000000 /* EMC_CTT_DURATION */
-				0x8000308c /* EMC_DYN_SELF_REF_CONTROL */
-				0xe8000000 /* EMC_FBIO_SPARE */
-				0xff00ff49 /* EMC_CFG_RSV */
-			>;
-		};
-	};
-	emc-timings-2 {
-		nvidia,ram-code = <2>;  /* Hynix A RAM */
-		timing-25500000 {
-			clock-frequency = <25500000>;
-			nvidia,emc-auto-cal-interval = <0x001fffff>;
-			nvidia,emc-mode-1 = <0x80100003>;
-			nvidia,emc-mode-2 = <0x80200008>;
-			nvidia,emc-mode-reset = <0x80001221>;
-			nvidia,emc-zcal-cnt-long = <0x00000040>;
-			nvidia,emc-cfg-periodic-qrst;
-			nvidia,emc-cfg-dyn-self-ref;
-			nvidia,emc-configuration = <
-				0x00000001 /* EMC_RC */
-				0x00000007 /* EMC_RFC */
-				0x00000000 /* EMC_RAS */
-				0x00000000 /* EMC_RP */
-				0x00000002 /* EMC_R2W */
-				0x0000000a /* EMC_W2R */
-				0x00000005 /* EMC_R2P */
-				0x0000000b /* EMC_W2P */
-				0x00000000 /* EMC_RD_RCD */
-				0x00000000 /* EMC_WR_RCD */
-				0x00000003 /* EMC_RRD */
-				0x00000001 /* EMC_REXT */
-				0x00000000 /* EMC_WEXT */
-				0x00000005 /* EMC_WDV */
-				0x00000005 /* EMC_QUSE */
-				0x00000004 /* EMC_QRST */
-				0x0000000a /* EMC_QSAFE */
-				0x0000000b /* EMC_RDV */
-				0x000000c0 /* EMC_REFRESH */
-				0x00000000 /* EMC_BURST_REFRESH_NUM */
-				0x00000030 /* EMC_PRE_REFRESH_REQ_CNT */
-				0x00000002 /* EMC_PDEX2WR */
-				0x00000002 /* EMC_PDEX2RD */
-				0x00000001 /* EMC_PCHG2PDEN */
-				0x00000000 /* EMC_ACT2PDEN */
-				0x00000007 /* EMC_AR2PDEN */
-				0x0000000f /* EMC_RW2PDEN */
-				0x00000008 /* EMC_TXSR */
-				0x00000008 /* EMC_TXSRDLL */
-				0x00000004 /* EMC_TCKE */
-				0x00000002 /* EMC_TFAW */
-				0x00000000 /* EMC_TRPAB */
-				0x00000004 /* EMC_TCLKSTABLE */
-				0x00000005 /* EMC_TCLKSTOP */
-				0x000000c7 /* EMC_TREFBW */
-				0x00000006 /* EMC_QUSE_EXTRA */
-				0x00000004 /* EMC_FBIO_CFG6 */
-				0x00000000 /* EMC_ODT_WRITE */
-				0x00000000 /* EMC_ODT_READ */
-				0x00004288 /* EMC_FBIO_CFG5 */
-				0x007800a4 /* EMC_CFG_DIG_DLL */
-				0x00008000 /* EMC_CFG_DIG_DLL_PERIOD */
-				0x000fc000 /* EMC_DLL_XFORM_DQS0 */
-				0x000fc000 /* EMC_DLL_XFORM_DQS1 */
-				0x000fc000 /* EMC_DLL_XFORM_DQS2 */
-				0x000fc000 /* EMC_DLL_XFORM_DQS3 */
-				0x000fc000 /* EMC_DLL_XFORM_DQS4 */
-				0x000fc000 /* EMC_DLL_XFORM_DQS5 */
-				0x000fc000 /* EMC_DLL_XFORM_DQS6 */
-				0x000fc000 /* EMC_DLL_XFORM_DQS7 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE0 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE1 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE2 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE3 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE4 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE5 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE6 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE7 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS0 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS1 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS2 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS3 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS4 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS5 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS6 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS7 */
-				0x000fc000 /* EMC_DLL_XFORM_DQ0 */
-				0x000fc000 /* EMC_DLL_XFORM_DQ1 */
-				0x000fc000 /* EMC_DLL_XFORM_DQ2 */
-				0x000fc000 /* EMC_DLL_XFORM_DQ3 */
-				0x000002a0 /* EMC_XM2CMDPADCTRL */
-				0x0800211c /* EMC_XM2DQSPADCTRL2 */
-				0x00000000 /* EMC_XM2DQPADCTRL2 */
-				0x77fff884 /* EMC_XM2CLKPADCTRL */
-				0x01f1f108 /* EMC_XM2COMPPADCTRL */
-				0x05057404 /* EMC_XM2VTTGENPADCTRL */
-				0x54000007 /* EMC_XM2VTTGENPADCTRL2 */
-				0x08000168 /* EMC_XM2QUSEPADCTRL */
-				0x08000000 /* EMC_XM2DQSPADCTRL3 */
-				0x00000802 /* EMC_CTT_TERM_CTRL */
-				0x00000000 /* EMC_ZCAL_INTERVAL */
-				0x00000040 /* EMC_ZCAL_WAIT_CNT */
-				0x000c000c /* EMC_MRS_WAIT_CNT */
-				0xa0f10000 /* EMC_AUTO_CAL_CONFIG */
-				0x00000000 /* EMC_CTT */
-				0x00000000 /* EMC_CTT_DURATION */
-				0x80000287 /* EMC_DYN_SELF_REF_CONTROL */
-				0xe8000000 /* EMC_FBIO_SPARE */
-				0xff00ff00 /* EMC_CFG_RSV */
-			>;
-		};
-		timing-51000000 {
-			clock-frequency = <51000000>;
-			nvidia,emc-auto-cal-interval = <0x001fffff>;
-			nvidia,emc-mode-1 = <0x80100003>;
-			nvidia,emc-mode-2 = <0x80200008>;
-			nvidia,emc-mode-reset = <0x80001221>;
-			nvidia,emc-zcal-cnt-long = <0x00000040>;
-			nvidia,emc-cfg-periodic-qrst;
-			nvidia,emc-cfg-dyn-self-ref;
-			nvidia,emc-configuration = <
-				0x00000002 /* EMC_RC */
-				0x0000000f /* EMC_RFC */
-				0x00000001 /* EMC_RAS */
-				0x00000000 /* EMC_RP */
-				0x00000002 /* EMC_R2W */
-				0x0000000a /* EMC_W2R */
-				0x00000005 /* EMC_R2P */
-				0x0000000b /* EMC_W2P */
-				0x00000000 /* EMC_RD_RCD */
-				0x00000000 /* EMC_WR_RCD */
-				0x00000003 /* EMC_RRD */
-				0x00000001 /* EMC_REXT */
-				0x00000000 /* EMC_WEXT */
-				0x00000005 /* EMC_WDV */
-				0x00000005 /* EMC_QUSE */
-				0x00000004 /* EMC_QRST */
-				0x0000000a /* EMC_QSAFE */
-				0x0000000b /* EMC_RDV */
-				0x00000181 /* EMC_REFRESH */
-				0x00000000 /* EMC_BURST_REFRESH_NUM */
-				0x00000060 /* EMC_PRE_REFRESH_REQ_CNT */
-				0x00000002 /* EMC_PDEX2WR */
-				0x00000002 /* EMC_PDEX2RD */
-				0x00000001 /* EMC_PCHG2PDEN */
-				0x00000000 /* EMC_ACT2PDEN */
-				0x00000007 /* EMC_AR2PDEN */
-				0x0000000f /* EMC_RW2PDEN */
-				0x00000010 /* EMC_TXSR */
-				0x00000010 /* EMC_TXSRDLL */
-				0x00000004 /* EMC_TCKE */
-				0x00000003 /* EMC_TFAW */
-				0x00000000 /* EMC_TRPAB */
-				0x00000004 /* EMC_TCLKSTABLE */
-				0x00000005 /* EMC_TCLKSTOP */
-				0x0000018e /* EMC_TREFBW */
-				0x00000006 /* EMC_QUSE_EXTRA */
-				0x00000004 /* EMC_FBIO_CFG6 */
-				0x00000000 /* EMC_ODT_WRITE */
-				0x00000000 /* EMC_ODT_READ */
-				0x00004288 /* EMC_FBIO_CFG5 */
-				0x007800a4 /* EMC_CFG_DIG_DLL */
-				0x00008000 /* EMC_CFG_DIG_DLL_PERIOD */
-				0x000fc000 /* EMC_DLL_XFORM_DQS0 */
-				0x000fc000 /* EMC_DLL_XFORM_DQS1 */
-				0x000fc000 /* EMC_DLL_XFORM_DQS2 */
-				0x000fc000 /* EMC_DLL_XFORM_DQS3 */
-				0x000fc000 /* EMC_DLL_XFORM_DQS4 */
-				0x000fc000 /* EMC_DLL_XFORM_DQS5 */
-				0x000fc000 /* EMC_DLL_XFORM_DQS6 */
-				0x000fc000 /* EMC_DLL_XFORM_DQS7 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE0 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE1 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE2 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE3 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE4 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE5 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE6 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE7 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS0 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS1 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS2 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS3 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS4 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS5 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS6 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS7 */
-				0x000fc000 /* EMC_DLL_XFORM_DQ0 */
-				0x000fc000 /* EMC_DLL_XFORM_DQ1 */
-				0x000fc000 /* EMC_DLL_XFORM_DQ2 */
-				0x000fc000 /* EMC_DLL_XFORM_DQ3 */
-				0x000002a0 /* EMC_XM2CMDPADCTRL */
-				0x0800211c /* EMC_XM2DQSPADCTRL2 */
-				0x00000000 /* EMC_XM2DQPADCTRL2 */
-				0x77fff884 /* EMC_XM2CLKPADCTRL */
-				0x01f1f108 /* EMC_XM2COMPPADCTRL */
-				0x05057404 /* EMC_XM2VTTGENPADCTRL */
-				0x54000007 /* EMC_XM2VTTGENPADCTRL2 */
-				0x08000168 /* EMC_XM2QUSEPADCTRL */
-				0x08000000 /* EMC_XM2DQSPADCTRL3 */
-				0x00000802 /* EMC_CTT_TERM_CTRL */
-				0x00000000 /* EMC_ZCAL_INTERVAL */
-				0x00000040 /* EMC_ZCAL_WAIT_CNT */
-				0x000c000c /* EMC_MRS_WAIT_CNT */
-				0xa0f10000 /* EMC_AUTO_CAL_CONFIG */
-				0x00000000 /* EMC_CTT */
-				0x00000000 /* EMC_CTT_DURATION */
-				0x8000040b /* EMC_DYN_SELF_REF_CONTROL */
-				0xe8000000 /* EMC_FBIO_SPARE */
-				0xff00ff00 /* EMC_CFG_RSV */
-			>;
-		};
-		timing-102000000 {
-			clock-frequency = <102000000>;
-			nvidia,emc-auto-cal-interval = <0x001fffff>;
-			nvidia,emc-mode-1 = <0x80100003>;
-			nvidia,emc-mode-2 = <0x80200008>;
-			nvidia,emc-mode-reset = <0x80001221>;
-			nvidia,emc-zcal-cnt-long = <0x00000040>;
-			nvidia,emc-cfg-periodic-qrst;
-			nvidia,emc-cfg-dyn-self-ref;
-			nvidia,emc-configuration = <
-				0x00000004 /* EMC_RC */
-				0x0000001e /* EMC_RFC */
-				0x00000003 /* EMC_RAS */
-				0x00000001 /* EMC_RP */
-				0x00000002 /* EMC_R2W */
-				0x0000000a /* EMC_W2R */
-				0x00000005 /* EMC_R2P */
-				0x0000000b /* EMC_W2P */
-				0x00000001 /* EMC_RD_RCD */
-				0x00000001 /* EMC_WR_RCD */
-				0x00000003 /* EMC_RRD */
-				0x00000001 /* EMC_REXT */
-				0x00000000 /* EMC_WEXT */
-				0x00000005 /* EMC_WDV */
-				0x00000005 /* EMC_QUSE */
-				0x00000004 /* EMC_QRST */
-				0x0000000a /* EMC_QSAFE */
-				0x0000000b /* EMC_RDV */
-				0x00000303 /* EMC_REFRESH */
-				0x00000000 /* EMC_BURST_REFRESH_NUM */
-				0x000000c0 /* EMC_PRE_REFRESH_REQ_CNT */
-				0x00000002 /* EMC_PDEX2WR */
-				0x00000002 /* EMC_PDEX2RD */
-				0x00000001 /* EMC_PCHG2PDEN */
-				0x00000000 /* EMC_ACT2PDEN */
-				0x00000007 /* EMC_AR2PDEN */
-				0x0000000f /* EMC_RW2PDEN */
-				0x00000020 /* EMC_TXSR */
-				0x00000020 /* EMC_TXSRDLL */
-				0x00000004 /* EMC_TCKE */
-				0x00000005 /* EMC_TFAW */
-				0x00000000 /* EMC_TRPAB */
-				0x00000004 /* EMC_TCLKSTABLE */
-				0x00000005 /* EMC_TCLKSTOP */
-				0x0000031c /* EMC_TREFBW */
-				0x00000006 /* EMC_QUSE_EXTRA */
-				0x00000004 /* EMC_FBIO_CFG6 */
-				0x00000000 /* EMC_ODT_WRITE */
-				0x00000000 /* EMC_ODT_READ */
-				0x00004288 /* EMC_FBIO_CFG5 */
-				0x007800a4 /* EMC_CFG_DIG_DLL */
-				0x00008000 /* EMC_CFG_DIG_DLL_PERIOD */
-				0x000fc000 /* EMC_DLL_XFORM_DQS0 */
-				0x000fc000 /* EMC_DLL_XFORM_DQS1 */
-				0x000fc000 /* EMC_DLL_XFORM_DQS2 */
-				0x000fc000 /* EMC_DLL_XFORM_DQS3 */
-				0x000fc000 /* EMC_DLL_XFORM_DQS4 */
-				0x000fc000 /* EMC_DLL_XFORM_DQS5 */
-				0x000fc000 /* EMC_DLL_XFORM_DQS6 */
-				0x000fc000 /* EMC_DLL_XFORM_DQS7 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE0 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE1 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE2 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE3 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE4 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE5 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE6 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE7 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS0 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS1 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS2 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS3 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS4 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS5 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS6 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS7 */
-				0x000fc000 /* EMC_DLL_XFORM_DQ0 */
-				0x000fc000 /* EMC_DLL_XFORM_DQ1 */
-				0x000fc000 /* EMC_DLL_XFORM_DQ2 */
-				0x000fc000 /* EMC_DLL_XFORM_DQ3 */
-				0x000002a0 /* EMC_XM2CMDPADCTRL */
-				0x0800211c /* EMC_XM2DQSPADCTRL2 */
-				0x00000000 /* EMC_XM2DQPADCTRL2 */
-				0x77fff884 /* EMC_XM2CLKPADCTRL */
-				0x01f1f108 /* EMC_XM2COMPPADCTRL */
-				0x05057404 /* EMC_XM2VTTGENPADCTRL */
-				0x54000007 /* EMC_XM2VTTGENPADCTRL2 */
-				0x08000168 /* EMC_XM2QUSEPADCTRL */
-				0x08000000 /* EMC_XM2DQSPADCTRL3 */
-				0x00000802 /* EMC_CTT_TERM_CTRL */
-				0x00000000 /* EMC_ZCAL_INTERVAL */
-				0x00000040 /* EMC_ZCAL_WAIT_CNT */
-				0x000c000c /* EMC_MRS_WAIT_CNT */
-				0xa0f10000 /* EMC_AUTO_CAL_CONFIG */
-				0x00000000 /* EMC_CTT */
-				0x00000000 /* EMC_CTT_DURATION */
-				0x80000713 /* EMC_DYN_SELF_REF_CONTROL */
-				0xe8000000 /* EMC_FBIO_SPARE */
-				0xff00ff00 /* EMC_CFG_RSV */
-			>;
-		};
-		timing-204000000 {
-			clock-frequency = <204000000>;
-			nvidia,emc-auto-cal-interval = <0x001fffff>;
-			nvidia,emc-mode-1 = <0x80100003>;
-			nvidia,emc-mode-2 = <0x80200008>;
-			nvidia,emc-mode-reset = <0x80001221>;
-			nvidia,emc-zcal-cnt-long = <0x00000040>;
-			nvidia,emc-cfg-periodic-qrst;
-			nvidia,emc-cfg-dyn-self-ref;
-			nvidia,emc-configuration = <
-				0x00000009 /* EMC_RC */
-				0x0000003d /* EMC_RFC */
-				0x00000007 /* EMC_RAS */
-				0x00000002 /* EMC_RP */
-				0x00000002 /* EMC_R2W */
-				0x0000000a /* EMC_W2R */
-				0x00000005 /* EMC_R2P */
-				0x0000000b /* EMC_W2P */
-				0x00000002 /* EMC_RD_RCD */
-				0x00000002 /* EMC_WR_RCD */
-				0x00000003 /* EMC_RRD */
-				0x00000001 /* EMC_REXT */
-				0x00000000 /* EMC_WEXT */
-				0x00000005 /* EMC_WDV */
-				0x00000005 /* EMC_QUSE */
-				0x00000004 /* EMC_QRST */
-				0x0000000a /* EMC_QSAFE */
-				0x0000000b /* EMC_RDV */
-				0x00000607 /* EMC_REFRESH */
-				0x00000000 /* EMC_BURST_REFRESH_NUM */
-				0x00000181 /* EMC_PRE_REFRESH_REQ_CNT */
-				0x00000002 /* EMC_PDEX2WR */
-				0x00000002 /* EMC_PDEX2RD */
-				0x00000001 /* EMC_PCHG2PDEN */
-				0x00000000 /* EMC_ACT2PDEN */
-				0x00000007 /* EMC_AR2PDEN */
-				0x0000000f /* EMC_RW2PDEN */
-				0x00000040 /* EMC_TXSR */
-				0x00000040 /* EMC_TXSRDLL */
-				0x00000004 /* EMC_TCKE */
-				0x00000009 /* EMC_TFAW */
-				0x00000000 /* EMC_TRPAB */
-				0x00000004 /* EMC_TCLKSTABLE */
-				0x00000005 /* EMC_TCLKSTOP */
-				0x00000638 /* EMC_TREFBW */
-				0x00000006 /* EMC_QUSE_EXTRA */
-				0x00000006 /* EMC_FBIO_CFG6 */
-				0x00000000 /* EMC_ODT_WRITE */
-				0x00000000 /* EMC_ODT_READ */
-				0x00004288 /* EMC_FBIO_CFG5 */
-				0x004400a4 /* EMC_CFG_DIG_DLL */
-				0x00008000 /* EMC_CFG_DIG_DLL_PERIOD */
-				0x00080000 /* EMC_DLL_XFORM_DQS0 */
-				0x00080000 /* EMC_DLL_XFORM_DQS1 */
-				0x00080000 /* EMC_DLL_XFORM_DQS2 */
-				0x00080000 /* EMC_DLL_XFORM_DQS3 */
-				0x00080000 /* EMC_DLL_XFORM_DQS4 */
-				0x00080000 /* EMC_DLL_XFORM_DQS5 */
-				0x00080000 /* EMC_DLL_XFORM_DQS6 */
-				0x00080000 /* EMC_DLL_XFORM_DQS7 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE0 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE1 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE2 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE3 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE4 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE5 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE6 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE7 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS0 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS1 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS2 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS3 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS4 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS5 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS6 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS7 */
-				0x00080000 /* EMC_DLL_XFORM_DQ0 */
-				0x00080000 /* EMC_DLL_XFORM_DQ1 */
-				0x00080000 /* EMC_DLL_XFORM_DQ2 */
-				0x00080000 /* EMC_DLL_XFORM_DQ3 */
-				0x000002a0 /* EMC_XM2CMDPADCTRL */
-				0x0800211c /* EMC_XM2DQSPADCTRL2 */
-				0x00000000 /* EMC_XM2DQPADCTRL2 */
-				0x77fff884 /* EMC_XM2CLKPADCTRL */
-				0x01f1f108 /* EMC_XM2COMPPADCTRL */
-				0x05057404 /* EMC_XM2VTTGENPADCTRL */
-				0x54000007 /* EMC_XM2VTTGENPADCTRL2 */
-				0x08000168 /* EMC_XM2QUSEPADCTRL */
-				0x08000000 /* EMC_XM2DQSPADCTRL3 */
-				0x00000802 /* EMC_CTT_TERM_CTRL */
-				0x00020000 /* EMC_ZCAL_INTERVAL */
-				0x00000100 /* EMC_ZCAL_WAIT_CNT */
-				0x000c000c /* EMC_MRS_WAIT_CNT */
-				0xa0f10000 /* EMC_AUTO_CAL_CONFIG */
-				0x00000000 /* EMC_CTT */
-				0x00000000 /* EMC_CTT_DURATION */
-				0x80000d22 /* EMC_DYN_SELF_REF_CONTROL */
-				0xe8000000 /* EMC_FBIO_SPARE */
-				0xff00ff00 /* EMC_CFG_RSV */
-			>;
-		};
-		timing-400000000 {
-			clock-frequency = <400000000>;
-			nvidia,emc-auto-cal-interval = <0x001fffff>;
-			nvidia,emc-mode-1 = <0x80100002>;
-			nvidia,emc-mode-2 = <0x80200000>;
-			nvidia,emc-mode-reset = <0x80000521>;
-			nvidia,emc-zcal-cnt-long = <0x00000040>;
-			nvidia,emc-configuration = <
-				0x00000012 /* EMC_RC */
-				0x00000076 /* EMC_RFC */
-				0x0000000c /* EMC_RAS */
-				0x00000004 /* EMC_RP */
-				0x00000003 /* EMC_R2W */
-				0x00000008 /* EMC_W2R */
-				0x00000002 /* EMC_R2P */
-				0x0000000a /* EMC_W2P */
-				0x00000004 /* EMC_RD_RCD */
-				0x00000004 /* EMC_WR_RCD */
-				0x00000002 /* EMC_RRD */
-				0x00000001 /* EMC_REXT */
-				0x00000000 /* EMC_WEXT */
-				0x00000004 /* EMC_WDV */
-				0x00000006 /* EMC_QUSE */
-				0x00000004 /* EMC_QRST */
-				0x0000000a /* EMC_QSAFE */
-				0x0000000c /* EMC_RDV */
-				0x00000bf0 /* EMC_REFRESH */
-				0x00000000 /* EMC_BURST_REFRESH_NUM */
-				0x000002fc /* EMC_PRE_REFRESH_REQ_CNT */
-				0x00000001 /* EMC_PDEX2WR */
-				0x00000008 /* EMC_PDEX2RD */
-				0x00000001 /* EMC_PCHG2PDEN */
-				0x00000000 /* EMC_ACT2PDEN */
-				0x00000008 /* EMC_AR2PDEN */
-				0x0000000f /* EMC_RW2PDEN */
-				0x0000007c /* EMC_TXSR */
-				0x00000200 /* EMC_TXSRDLL */
-				0x00000004 /* EMC_TCKE */
-				0x00000010 /* EMC_TFAW */
-				0x00000000 /* EMC_TRPAB */
-				0x00000004 /* EMC_TCLKSTABLE */
-				0x00000005 /* EMC_TCLKSTOP */
-				0x00000c30 /* EMC_TREFBW */
-				0x00000000 /* EMC_QUSE_EXTRA */
-				0x00000004 /* EMC_FBIO_CFG6 */
-				0x00000000 /* EMC_ODT_WRITE */
-				0x00000000 /* EMC_ODT_READ */
-				0x00007088 /* EMC_FBIO_CFG5 */
-				0x001d0084 /* EMC_CFG_DIG_DLL */
-				0x00008000 /* EMC_CFG_DIG_DLL_PERIOD */
-				0x00044000 /* EMC_DLL_XFORM_DQS0 */
-				0x00044000 /* EMC_DLL_XFORM_DQS1 */
-				0x00044000 /* EMC_DLL_XFORM_DQS2 */
-				0x00044000 /* EMC_DLL_XFORM_DQS3 */
-				0x00044000 /* EMC_DLL_XFORM_DQS4 */
-				0x00044000 /* EMC_DLL_XFORM_DQS5 */
-				0x00044000 /* EMC_DLL_XFORM_DQS6 */
-				0x00044000 /* EMC_DLL_XFORM_DQS7 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE0 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE1 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE2 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE3 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE4 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE5 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE6 */
-				0x00000000 /* EMC_DLL_XFORM_QUSE7 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS0 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS1 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS2 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS3 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS4 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS5 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS6 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS7 */
-				0x00058000 /* EMC_DLL_XFORM_DQ0 */
-				0x00058000 /* EMC_DLL_XFORM_DQ1 */
-				0x00058000 /* EMC_DLL_XFORM_DQ2 */
-				0x00058000 /* EMC_DLL_XFORM_DQ3 */
-				0x000002a0 /* EMC_XM2CMDPADCTRL */
-				0x0800013d /* EMC_XM2DQSPADCTRL2 */
-				0x00000000 /* EMC_XM2DQPADCTRL2 */
-				0x77fff884 /* EMC_XM2CLKPADCTRL */
-				0x01f1f508 /* EMC_XM2COMPPADCTRL */
-				0x05057404 /* EMC_XM2VTTGENPADCTRL */
-				0x54000007 /* EMC_XM2VTTGENPADCTRL2 */
-				0x080001e8 /* EMC_XM2QUSEPADCTRL */
-				0x08000021 /* EMC_XM2DQSPADCTRL3 */
-				0x00000802 /* EMC_CTT_TERM_CTRL */
-				0x00020000 /* EMC_ZCAL_INTERVAL */
-				0x00000100 /* EMC_ZCAL_WAIT_CNT */
-				0x0148000c /* EMC_MRS_WAIT_CNT */
-				0xa0f10000 /* EMC_AUTO_CAL_CONFIG */
-				0x00000000 /* EMC_CTT */
-				0x00000000 /* EMC_CTT_DURATION */
-				0x800018c8 /* EMC_DYN_SELF_REF_CONTROL */
-				0xe8000000 /* EMC_FBIO_SPARE */
-				0xff00ff89 /* EMC_CFG_RSV */
-			>;
-		};
-		timing-800000000 {
-			clock-frequency = <800000000>;
-			nvidia,emc-auto-cal-interval = <0x001fffff>;
-			nvidia,emc-mode-1 = <0x80100002>;
-			nvidia,emc-mode-2 = <0x80200018>;
-			nvidia,emc-mode-reset = <0x80000d71>;
-			nvidia,emc-zcal-cnt-long = <0x00000040>;
-			nvidia,emc-cfg-periodic-qrst;
-			nvidia,emc-configuration = <
-				0x00000025 /* EMC_RC */
-				0x000000ee /* EMC_RFC */
-				0x0000001a /* EMC_RAS */
-				0x00000009 /* EMC_RP */
-				0x00000005 /* EMC_R2W */
-				0x0000000d /* EMC_W2R */
-				0x00000004 /* EMC_R2P */
-				0x00000013 /* EMC_W2P */
-				0x00000009 /* EMC_RD_RCD */
-				0x00000009 /* EMC_WR_RCD */
-				0x00000003 /* EMC_RRD */
-				0x00000001 /* EMC_REXT */
-				0x00000000 /* EMC_WEXT */
-				0x00000007 /* EMC_WDV */
-				0x0000000a /* EMC_QUSE */
-				0x00000009 /* EMC_QRST */
-				0x0000000b /* EMC_QSAFE */
-				0x00000011 /* EMC_RDV */
-				0x00001820 /* EMC_REFRESH */
-				0x00000000 /* EMC_BURST_REFRESH_NUM */
-				0x00000608 /* EMC_PRE_REFRESH_REQ_CNT */
-				0x00000003 /* EMC_PDEX2WR */
-				0x00000012 /* EMC_PDEX2RD */
-				0x00000001 /* EMC_PCHG2PDEN */
-				0x00000000 /* EMC_ACT2PDEN */
-				0x0000000f /* EMC_AR2PDEN */
-				0x00000018 /* EMC_RW2PDEN */
-				0x000000f8 /* EMC_TXSR */
-				0x00000200 /* EMC_TXSRDLL */
-				0x00000005 /* EMC_TCKE */
-				0x00000020 /* EMC_TFAW */
-				0x00000000 /* EMC_TRPAB */
-				0x00000007 /* EMC_TCLKSTABLE */
-				0x00000008 /* EMC_TCLKSTOP */
-				0x00001860 /* EMC_TREFBW */
-				0x0000000b /* EMC_QUSE_EXTRA */
-				0x00000006 /* EMC_FBIO_CFG6 */
-				0x00000000 /* EMC_ODT_WRITE */
-				0x00000000 /* EMC_ODT_READ */
-				0x00005088 /* EMC_FBIO_CFG5 */
-				0xf0070191 /* EMC_CFG_DIG_DLL */
-				0x00008000 /* EMC_CFG_DIG_DLL_PERIOD */
-				0x0000000c /* EMC_DLL_XFORM_DQS0 */
-				0x007fc00a /* EMC_DLL_XFORM_DQS1 */
-				0x00000008 /* EMC_DLL_XFORM_DQS2 */
-				0x0000000a /* EMC_DLL_XFORM_DQS3 */
-				0x0000000a /* EMC_DLL_XFORM_DQS4 */
-				0x0000000a /* EMC_DLL_XFORM_DQS5 */
-				0x0000000a /* EMC_DLL_XFORM_DQS6 */
-				0x0000000a /* EMC_DLL_XFORM_DQS7 */
-				0x00018000 /* EMC_DLL_XFORM_QUSE0 */
-				0x00018000 /* EMC_DLL_XFORM_QUSE1 */
-				0x00018000 /* EMC_DLL_XFORM_QUSE2 */
-				0x00018000 /* EMC_DLL_XFORM_QUSE3 */
-				0x00018000 /* EMC_DLL_XFORM_QUSE4 */
-				0x00018000 /* EMC_DLL_XFORM_QUSE5 */
-				0x00018000 /* EMC_DLL_XFORM_QUSE6 */
-				0x00018000 /* EMC_DLL_XFORM_QUSE7 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS0 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS1 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS2 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS3 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS4 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS5 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS6 */
-				0x00000000 /* EMC_DLI_TRIM_TXDQS7 */
-				0x0000000a /* EMC_DLL_XFORM_DQ0 */
-				0x0000000c /* EMC_DLL_XFORM_DQ1 */
-				0x0000000a /* EMC_DLL_XFORM_DQ2 */
-				0x0000000a /* EMC_DLL_XFORM_DQ3 */
-				0x000002a0 /* EMC_XM2CMDPADCTRL */
-				0x0600013d /* EMC_XM2DQSPADCTRL2 */
-				0x22220000 /* EMC_XM2DQPADCTRL2 */
-				0x77fff884 /* EMC_XM2CLKPADCTRL */
-				0x01f1f501 /* EMC_XM2COMPPADCTRL */
-				0x07077404 /* EMC_XM2VTTGENPADCTRL */
-				0x54000000 /* EMC_XM2VTTGENPADCTRL2 */
-				0x080001e8 /* EMC_XM2QUSEPADCTRL */
-				0x0a000021 /* EMC_XM2DQSPADCTRL3 */
-				0x00000802 /* EMC_CTT_TERM_CTRL */
-				0x00020000 /* EMC_ZCAL_INTERVAL */
-				0x00000100 /* EMC_ZCAL_WAIT_CNT */
-				0x00d0000c /* EMC_MRS_WAIT_CNT */
-				0xa0f10000 /* EMC_AUTO_CAL_CONFIG */
-				0x00000000 /* EMC_CTT */
-				0x00000000 /* EMC_CTT_DURATION */
-				0x8000308c /* EMC_DYN_SELF_REF_CONTROL */
-				0xe8000000 /* EMC_FBIO_SPARE */
-				0xff00ff49 /* EMC_CFG_RSV */
-			>;
-		};
-	};
-};
-&state_default {
-	clk_32k_out_pa0 {
-		nvidia,pins = "clk_32k_out_pa0";
-		nvidia,function = "blink";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	uart3_cts_n_pa1 {
-		nvidia,pins = "uart3_cts_n_pa1";
-		nvidia,function = "uartc";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_ENABLE>;
-	};
-	dap2_fs_pa2 {
-		nvidia,pins = "dap2_fs_pa2";
-		nvidia,function = "i2s1";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_ENABLE>;
-	};
-	dap2_sclk_pa3 {
-		nvidia,pins = "dap2_sclk_pa3";
-		nvidia,function = "i2s1";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_ENABLE>;
-	};
-	dap2_din_pa4 {
-		nvidia,pins = "dap2_din_pa4";
-		nvidia,function = "i2s1";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_ENABLE>;
-	};
-	dap2_dout_pa5 {
-		nvidia,pins = "dap2_dout_pa5";
-		nvidia,function = "i2s1";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_ENABLE>;
-	};
-	sdmmc3_clk_pa6 {
-		nvidia,pins = "sdmmc3_clk_pa6";
-		nvidia,function = "sdmmc3";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_ENABLE>;
-	};
-	sdmmc3_cmd_pa7 {
-		nvidia,pins = "sdmmc3_cmd_pa7";
-		nvidia,function = "sdmmc3";
-		nvidia,pull = <TEGRA_PIN_PULL_UP>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_ENABLE>;
-	};
-	gmi_a17_pb0 {
-		nvidia,pins = "gmi_a17_pb0";
-		nvidia,function = "spi4";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	gmi_a18_pb1 {
-		nvidia,pins = "gmi_a18_pb1";
-		nvidia,function = "spi4";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	lcd_pwr0_pb2 {
-		nvidia,pins = "lcd_pwr0_pb2";
-		nvidia,function = "displaya";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	lcd_pclk_pb3 {
-		nvidia,pins = "lcd_pclk_pb3";
-		nvidia,function = "displaya";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	sdmmc3_dat3_pb4 {
-		nvidia,pins = "sdmmc3_dat3_pb4";
-		nvidia,function = "sdmmc3";
-		nvidia,pull = <TEGRA_PIN_PULL_UP>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_ENABLE>;
-	};
-	sdmmc3_dat2_pb5 {
-		nvidia,pins = "sdmmc3_dat2_pb5";
-		nvidia,function = "sdmmc3";
-		nvidia,pull = <TEGRA_PIN_PULL_UP>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_ENABLE>;
-	};
-	sdmmc3_dat1_pb6 {
-		nvidia,pins = "sdmmc3_dat1_pb6";
-		nvidia,function = "sdmmc3";
-		nvidia,pull = <TEGRA_PIN_PULL_UP>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_ENABLE>;
-	};
-	sdmmc3_dat0_pb7 {
-		nvidia,pins = "sdmmc3_dat0_pb7";
-		nvidia,function = "sdmmc3";
-		nvidia,pull = <TEGRA_PIN_PULL_UP>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_ENABLE>;
-	};
-	uart3_rts_n_pc0 {
-		nvidia,pins = "uart3_rts_n_pc0";
-		nvidia,function = "uartc";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	lcd_pwr1_pc1 {
-		nvidia,pins = "lcd_pwr1_pc1";
-		nvidia,function = "displaya";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	uart2_txd_pc2 {
-		nvidia,pins = "uart2_txd_pc2";
-		nvidia,function = "uartb";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	uart2_rxd_pc3 {
-		nvidia,pins = "uart2_rxd_pc3";
-		nvidia,function = "uartb";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	gen1_i2c_scl_pc4 {
-		nvidia,pins = "gen1_i2c_scl_pc4";
-		nvidia,function = "i2c1";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-		nvidia,open-drain = <TEGRA_PIN_DISABLE>;
-	};
-	gen1_i2c_sda_pc5 {
-		nvidia,pins = "gen1_i2c_sda_pc5";
-		nvidia,function = "i2c1";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-		nvidia,open-drain = <TEGRA_PIN_DISABLE>;
-	};
-	lcd_pwr2_pc6 {
-		nvidia,pins = "lcd_pwr2_pc6";
-		nvidia,function = "displaya";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	gmi_wp_n_pc7 {
-		nvidia,pins = "gmi_wp_n_pc7";
-		nvidia,function = "gmi";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_ENABLE>;
-	};
-	sdmmc3_dat5_pd0 {
-		nvidia,pins = "sdmmc3_dat5_pd0";
-		nvidia,function = "sdmmc3";
-		nvidia,pull = <TEGRA_PIN_PULL_UP>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	sdmmc3_dat4_pd1 {
-		nvidia,pins = "sdmmc3_dat4_pd1";
-		nvidia,function = "sdmmc3";
-		nvidia,pull = <TEGRA_PIN_PULL_UP>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_ENABLE>;
-	};
-	lcd_dc1_pd2 {
-		nvidia,pins = "lcd_dc1_pd2";
-		nvidia,function = "displaya";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	sdmmc3_dat6_pd3 {
-		nvidia,pins = "sdmmc3_dat6_pd3";
-		nvidia,function = "spi4";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	sdmmc3_dat7_pd4 {
-		nvidia,pins = "sdmmc3_dat7_pd4";
-		nvidia,function = "spi4";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	vi_d1_pd5 {
-		nvidia,pins = "vi_d1_pd5";
-		nvidia,function = "sdmmc2";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_ENABLE>;
-	};
-	vi_vsync_pd6 {
-		nvidia,pins = "vi_vsync_pd6";
-		nvidia,function = "ddr";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_ENABLE>;
-	};
-	vi_hsync_pd7 {
-		nvidia,pins = "vi_hsync_pd7";
-		nvidia,function = "ddr";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_ENABLE>;
-	};
-	lcd_d0_pe0 {
-		nvidia,pins = "lcd_d0_pe0";
-		nvidia,function = "displaya";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	lcd_d1_pe1 {
-		nvidia,pins = "lcd_d1_pe1";
-		nvidia,function = "displaya";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	lcd_d2_pe2 {
-		nvidia,pins = "lcd_d2_pe2";
-		nvidia,function = "displaya";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	lcd_d3_pe3 {
-		nvidia,pins = "lcd_d3_pe3";
-		nvidia,function = "displaya";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	lcd_d4_pe4 {
-		nvidia,pins = "lcd_d4_pe4";
-		nvidia,function = "displaya";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	lcd_d5_pe5 {
-		nvidia,pins = "lcd_d5_pe5";
-		nvidia,function = "displaya";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	lcd_d6_pe6 {
-		nvidia,pins = "lcd_d6_pe6";
-		nvidia,function = "displaya";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	lcd_d7_pe7 {
-		nvidia,pins = "lcd_d7_pe7";
-		nvidia,function = "displaya";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	lcd_d8_pf0 {
-		nvidia,pins = "lcd_d8_pf0";
-		nvidia,function = "displaya";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	lcd_d9_pf1 {
-		nvidia,pins = "lcd_d9_pf1";
-		nvidia,function = "displaya";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	lcd_d10_pf2 {
-		nvidia,pins = "lcd_d10_pf2";
-		nvidia,function = "displaya";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	lcd_d11_pf3 {
-		nvidia,pins = "lcd_d11_pf3";
-		nvidia,function = "displaya";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	lcd_d12_pf4 {
-		nvidia,pins = "lcd_d12_pf4";
-		nvidia,function = "displaya";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	lcd_d13_pf5 {
-		nvidia,pins = "lcd_d13_pf5";
-		nvidia,function = "displaya";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	lcd_d14_pf6 {
-		nvidia,pins = "lcd_d14_pf6";
-		nvidia,function = "displaya";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	lcd_d15_pf7 {
-		nvidia,pins = "lcd_d15_pf7";
-		nvidia,function = "displaya";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	gmi_ad0_pg0 {
-		nvidia,pins = "gmi_ad0_pg0";
-		nvidia,function = "nand";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_ENABLE>;
-	};
-	gmi_ad1_pg1 {
-		nvidia,pins = "gmi_ad1_pg1";
-		nvidia,function = "nand";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	gmi_ad2_pg2 {
-		nvidia,pins = "gmi_ad2_pg2";
-		nvidia,function = "nand";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_ENABLE>;
-	};
-	gmi_ad3_pg3 {
-		nvidia,pins = "gmi_ad3_pg3";
-		nvidia,function = "nand";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_ENABLE>;
-	};
-	gmi_ad4_pg4 {
-		nvidia,pins = "gmi_ad4_pg4";
-		nvidia,function = "nand";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_ENABLE>;
-	};
-	gmi_ad5_pg5 {
-		nvidia,pins = "gmi_ad5_pg5";
-		nvidia,function = "nand";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_ENABLE>;
-	};
-	gmi_ad6_pg6 {
-		nvidia,pins = "gmi_ad6_pg6";
-		nvidia,function = "nand";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_ENABLE>;
-	};
-	gmi_ad7_pg7 {
-		nvidia,pins = "gmi_ad7_pg7";
-		nvidia,function = "nand";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_ENABLE>;
-	};
-	gmi_ad8_ph0 {
-		nvidia,pins = "gmi_ad8_ph0";
-		nvidia,function = "pwm0";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	gmi_ad9_ph1 {
-		nvidia,pins = "gmi_ad9_ph1";
-		nvidia,function = "pwm1";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	gmi_ad10_ph2 {
-		nvidia,pins = "gmi_ad10_ph2";
-		nvidia,function = "pwm2";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	gmi_ad11_ph3 {
-		nvidia,pins = "gmi_ad11_ph3";
-		nvidia,function = "nand";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	gmi_ad12_ph4 {
-		nvidia,pins = "gmi_ad12_ph4";
-		nvidia,function = "nand";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	gmi_ad13_ph5 {
-		nvidia,pins = "gmi_ad13_ph5";
-		nvidia,function = "nand";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	gmi_ad14_ph6 {
-		nvidia,pins = "gmi_ad14_ph6";
-		nvidia,function = "nand";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	gmi_wr_n_pi0 {
-		nvidia,pins = "gmi_wr_n_pi0";
-		nvidia,function = "nand";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	gmi_oe_n_pi1 {
-		nvidia,pins = "gmi_oe_n_pi1";
-		nvidia,function = "nand";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	gmi_dqs_pi2 {
-		nvidia,pins = "gmi_dqs_pi2";
-		nvidia,function = "nand";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	gmi_iordy_pi5 {
-		nvidia,pins = "gmi_iordy_pi5";
-		nvidia,function = "rsvd1";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	gmi_cs7_n_pi6 {
-		nvidia,pins = "gmi_cs7_n_pi6";
-		nvidia,function = "nand";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	gmi_wait_pi7 {
-		nvidia,pins = "gmi_wait_pi7";
-		nvidia,function = "nand";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	lcd_de_pj1 {
-		nvidia,pins = "lcd_de_pj1";
-		nvidia,function = "displaya";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	gmi_cs1_n_pj2 {
-		nvidia,pins = "gmi_cs1_n_pj2";
-		nvidia,function = "rsvd1";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	lcd_hsync_pj3 {
-		nvidia,pins = "lcd_hsync_pj3";
-		nvidia,function = "displaya";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	lcd_vsync_pj4 {
-		nvidia,pins = "lcd_vsync_pj4";
-		nvidia,function = "displaya";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	uart2_cts_n_pj5 {
-		nvidia,pins = "uart2_cts_n_pj5";
-		nvidia,function = "uartb";
-		nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	uart2_rts_n_pj6 {
-		nvidia,pins = "uart2_rts_n_pj6";
-		nvidia,function = "uartb";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	gmi_a16_pj7 {
-		nvidia,pins = "gmi_a16_pj7";
-		nvidia,function = "spi4";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	gmi_adv_n_pk0 {
-		nvidia,pins = "gmi_adv_n_pk0";
-		nvidia,function = "nand";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	gmi_clk_pk1 {
-		nvidia,pins = "gmi_clk_pk1";
-		nvidia,function = "nand";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	gmi_cs2_n_pk3 {
-		nvidia,pins = "gmi_cs2_n_pk3";
-		nvidia,function = "rsvd1";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	gmi_cs3_n_pk4 {
-		nvidia,pins = "gmi_cs3_n_pk4";
-		nvidia,function = "nand";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	spdif_out_pk5 {
-		nvidia,pins = "spdif_out_pk5";
-		nvidia,function = "spdif";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	spdif_in_pk6 {
-		nvidia,pins = "spdif_in_pk6";
-		nvidia,function = "spdif";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_ENABLE>;
-	};
-	gmi_a19_pk7 {
-		nvidia,pins = "gmi_a19_pk7";
-		nvidia,function = "spi4";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	vi_d2_pl0 {
-		nvidia,pins = "vi_d2_pl0";
-		nvidia,function = "sdmmc2";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	vi_d3_pl1 {
-		nvidia,pins = "vi_d3_pl1";
-		nvidia,function = "sdmmc2";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	vi_d4_pl2 {
-		nvidia,pins = "vi_d4_pl2";
-		nvidia,function = "vi";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	vi_d5_pl3 {
-		nvidia,pins = "vi_d5_pl3";
-		nvidia,function = "sdmmc2";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	vi_d6_pl4 {
-		nvidia,pins = "vi_d6_pl4";
-		nvidia,function = "vi";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	vi_d7_pl5 {
-		nvidia,pins = "vi_d7_pl5";
-		nvidia,function = "sdmmc2";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	vi_d8_pl6 {
-		nvidia,pins = "vi_d8_pl6";
-		nvidia,function = "sdmmc2";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	vi_d9_pl7 {
-		nvidia,pins = "vi_d9_pl7";
-		nvidia,function = "sdmmc2";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	lcd_d16_pm0 {
-		nvidia,pins = "lcd_d16_pm0";
-		nvidia,function = "displaya";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	lcd_d17_pm1 {
-		nvidia,pins = "lcd_d17_pm1";
-		nvidia,function = "displaya";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	lcd_d18_pm2 {
-		nvidia,pins = "lcd_d18_pm2";
-		nvidia,function = "displaya";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	lcd_d19_pm3 {
-		nvidia,pins = "lcd_d19_pm3";
-		nvidia,function = "displaya";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	lcd_d20_pm4 {
-		nvidia,pins = "lcd_d20_pm4";
-		nvidia,function = "displaya";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	lcd_d21_pm5 {
-		nvidia,pins = "lcd_d21_pm5";
-		nvidia,function = "displaya";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	lcd_d22_pm6 {
-		nvidia,pins = "lcd_d22_pm6";
-		nvidia,function = "displaya";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	lcd_d23_pm7 {
-		nvidia,pins = "lcd_d23_pm7";
-		nvidia,function = "displaya";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	dap1_fs_pn0 {
-		nvidia,pins = "dap1_fs_pn0";
-		nvidia,function = "i2s0";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_ENABLE>;
-	};
-	dap1_din_pn1 {
-		nvidia,pins = "dap1_din_pn1";
-		nvidia,function = "i2s0";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_ENABLE>;
-	};
-	dap1_dout_pn2 {
-		nvidia,pins = "dap1_dout_pn2";
-		nvidia,function = "i2s0";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_ENABLE>;
-	};
-	dap1_sclk_pn3 {
-		nvidia,pins = "dap1_sclk_pn3";
-		nvidia,function = "i2s0";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_ENABLE>;
-	};
-	lcd_cs0_n_pn4 {
-		nvidia,pins = "lcd_cs0_n_pn4";
-		nvidia,function = "displaya";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	lcd_sdout_pn5 {
-		nvidia,pins = "lcd_sdout_pn5";
-		nvidia,function = "displaya";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	lcd_dc0_pn6 {
-		nvidia,pins = "lcd_dc0_pn6";
-		nvidia,function = "displaya";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	hdmi_int_pn7 {
-		nvidia,pins = "hdmi_int_pn7";
-		nvidia,function = "hdmi";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_ENABLE>;
-	};
-	ulpi_data7_po0 {
-		nvidia,pins = "ulpi_data7_po0";
-		nvidia,function = "uarta";
-		nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	ulpi_data0_po1 {
-		nvidia,pins = "ulpi_data0_po1";
-		nvidia,function = "uarta";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	ulpi_data1_po2 {
-		nvidia,pins = "ulpi_data1_po2";
-		nvidia,function = "uarta";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	ulpi_data2_po3 {
-		nvidia,pins = "ulpi_data2_po3";
-		nvidia,function = "uarta";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	ulpi_data3_po4 {
-		nvidia,pins = "ulpi_data3_po4";
-		nvidia,function = "uarta";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_ENABLE>;
-	};
-	ulpi_data4_po5 {
-		nvidia,pins = "ulpi_data4_po5";
-		nvidia,function = "uarta";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	ulpi_data5_po6 {
-		nvidia,pins = "ulpi_data5_po6";
-		nvidia,function = "uarta";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	ulpi_data6_po7 {
-		nvidia,pins = "ulpi_data6_po7";
-		nvidia,function = "uarta";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	dap3_fs_pp0 {
-		nvidia,pins = "dap3_fs_pp0";
-		nvidia,function = "i2s2";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_ENABLE>;
-	};
-	dap3_din_pp1 {
-		nvidia,pins = "dap3_din_pp1";
-		nvidia,function = "i2s2";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_ENABLE>;
-	};
-	dap3_dout_pp2 {
-		nvidia,pins = "dap3_dout_pp2";
-		nvidia,function = "i2s2";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_ENABLE>;
-	};
-	dap3_sclk_pp3 {
-		nvidia,pins = "dap3_sclk_pp3";
-		nvidia,function = "i2s2";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_ENABLE>;
-	};
-	dap4_fs_pp4 {
-		nvidia,pins = "dap4_fs_pp4";
-		nvidia,function = "i2s3";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_ENABLE>;
-	};
-	dap4_din_pp5 {
-		nvidia,pins = "dap4_din_pp5";
-		nvidia,function = "i2s3";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_ENABLE>;
-	};
-	dap4_dout_pp6 {
-		nvidia,pins = "dap4_dout_pp6";
-		nvidia,function = "i2s3";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_ENABLE>;
-	};
-	dap4_sclk_pp7 {
-		nvidia,pins = "dap4_sclk_pp7";
-		nvidia,function = "i2s3";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_ENABLE>;
-	};
-	kb_col0_pq0 {
-		nvidia,pins = "kb_col0_pq0";
-		nvidia,function = "kbc";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	kb_col1_pq1 {
-		nvidia,pins = "kb_col1_pq1";
-		nvidia,function = "kbc";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	kb_col2_pq2 {
-		nvidia,pins = "kb_col2_pq2";
-		nvidia,function = "kbc";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	kb_col3_pq3 {
-		nvidia,pins = "kb_col3_pq3";
-		nvidia,function = "kbc";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	kb_col4_pq4 {
-		nvidia,pins = "kb_col4_pq4";
-		nvidia,function = "kbc";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	kb_col5_pq5 {
-		nvidia,pins = "kb_col5_pq5";
-		nvidia,function = "kbc";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	kb_col6_pq6 {
-		nvidia,pins = "kb_col6_pq6";
-		nvidia,function = "kbc";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	kb_col7_pq7 {
-		nvidia,pins = "kb_col7_pq7";
-		nvidia,function = "kbc";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	kb_row0_pr0 {
-		nvidia,pins = "kb_row0_pr0";
-		nvidia,function = "kbc";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	kb_row1_pr1 {
-		nvidia,pins = "kb_row1_pr1";
-		nvidia,function = "kbc";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	kb_row2_pr2 {
-		nvidia,pins = "kb_row2_pr2";
-		nvidia,function = "kbc";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	kb_row3_pr3 {
-		nvidia,pins = "kb_row3_pr3";
-		nvidia,function = "kbc";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	kb_row4_pr4 {
-		nvidia,pins = "kb_row4_pr4";
-		nvidia,function = "kbc";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	kb_row5_pr5 {
-		nvidia,pins = "kb_row5_pr5";
-		nvidia,function = "kbc";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	kb_row6_pr6 {
-		nvidia,pins = "kb_row6_pr6";
-		nvidia,function = "kbc";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	kb_row7_pr7 {
-		nvidia,pins = "kb_row7_pr7";
-		nvidia,function = "kbc";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_ENABLE>;
-	};
-	kb_row8_ps0 {
-		nvidia,pins = "kb_row8_ps0";
-		nvidia,function = "kbc";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	kb_row9_ps1 {
-		nvidia,pins = "kb_row9_ps1";
-		nvidia,function = "kbc";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	kb_row10_ps2 {
-		nvidia,pins = "kb_row10_ps2";
-		nvidia,function = "kbc";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	kb_row11_ps3 {
-		nvidia,pins = "kb_row11_ps3";
-		nvidia,function = "kbc";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	kb_row12_ps4 {
-		nvidia,pins = "kb_row12_ps4";
-		nvidia,function = "kbc";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	kb_row13_ps5 {
-		nvidia,pins = "kb_row13_ps5";
-		nvidia,function = "kbc";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	kb_row14_ps6 {
-		nvidia,pins = "kb_row14_ps6";
-		nvidia,function = "kbc";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	kb_row15_ps7 {
-		nvidia,pins = "kb_row15_ps7";
-		nvidia,function = "kbc";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	vi_pclk_pt0 {
-		nvidia,pins = "vi_pclk_pt0";
-		nvidia,function = "rsvd1";
-		nvidia,pull = <TEGRA_PIN_PULL_UP>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	vi_mclk_pt1 {
-		nvidia,pins = "vi_mclk_pt1";
-		nvidia,function = "vi";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	vi_d10_pt2 {
-		nvidia,pins = "vi_d10_pt2";
-		nvidia,function = "ddr";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_ENABLE>;
-	};
-	vi_d11_pt3 {
-		nvidia,pins = "vi_d11_pt3";
-		nvidia,function = "ddr";
-		nvidia,pull = <TEGRA_PIN_PULL_UP>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_ENABLE>;
-	};
-	vi_d0_pt4 {
-		nvidia,pins = "vi_d0_pt4";
-		nvidia,function = "ddr";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_ENABLE>;
-	};
-	gen2_i2c_scl_pt5 {
-		nvidia,pins = "gen2_i2c_scl_pt5";
-		nvidia,function = "i2c2";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-		nvidia,open-drain = <TEGRA_PIN_DISABLE>;
-	};
-	gen2_i2c_sda_pt6 {
-		nvidia,pins = "gen2_i2c_sda_pt6";
-		nvidia,function = "i2c2";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-		nvidia,open-drain = <TEGRA_PIN_DISABLE>;
-	};
-	sdmmc4_cmd_pt7 {
-		nvidia,pins = "sdmmc4_cmd_pt7";
-		nvidia,function = "sdmmc4";
-		nvidia,pull = <TEGRA_PIN_PULL_UP>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_ENABLE>;
-		nvidia,io-reset = <TEGRA_PIN_DISABLE>;
-	};
-	pu0 {
-		nvidia,pins = "pu0";
-		nvidia,function = "owr";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	pu1 {
-		nvidia,pins = "pu1";
-		nvidia,function = "rsvd1";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	pu2 {
-		nvidia,pins = "pu2";
-		nvidia,function = "rsvd1";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	pu3 {
-		nvidia,pins = "pu3";
-		nvidia,function = "pwm0";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	pu4 {
-		nvidia,pins = "pu4";
-		nvidia,function = "pwm1";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	pu5 {
-		nvidia,pins = "pu5";
-		nvidia,function = "rsvd4";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	pu6 {
-		nvidia,pins = "pu6";
-		nvidia,function = "pwm3";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_ENABLE>;
-	};
-	jtag_rtck_pu7 {
-		nvidia,pins = "jtag_rtck_pu7";
-		nvidia,function = "rtck";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	pv0 {
-		nvidia,pins = "pv0";
-		nvidia,function = "rsvd1";
-		nvidia,pull = <TEGRA_PIN_PULL_UP>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_ENABLE>;
-	};
-	pv1 {
-		nvidia,pins = "pv1";
-		nvidia,function = "rsvd1";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	pv2 {
-		nvidia,pins = "pv2";
-		nvidia,function = "owr";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	pv3 {
-		nvidia,pins = "pv3";
-		nvidia,function = "clk_12m_out";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	ddc_scl_pv4 {
-		nvidia,pins = "ddc_scl_pv4";
-		nvidia,function = "i2c4";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_ENABLE>;
-	};
-	ddc_sda_pv5 {
-		nvidia,pins = "ddc_sda_pv5";
-		nvidia,function = "i2c4";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_ENABLE>;
-	};
-	crt_hsync_pv6 {
-		nvidia,pins = "crt_hsync_pv6";
-		nvidia,function = "crt";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	crt_vsync_pv7 {
-		nvidia,pins = "crt_vsync_pv7";
-		nvidia,function = "crt";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	lcd_cs1_n_pw0 {
-		nvidia,pins = "lcd_cs1_n_pw0";
-		nvidia,function = "displaya";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	lcd_m1_pw1 {
-		nvidia,pins = "lcd_m1_pw1";
-		nvidia,function = "displaya";
-		nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	spi2_cs1_n_pw2 {
-		nvidia,pins = "spi2_cs1_n_pw2";
-		nvidia,function = "spi2";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	clk1_out_pw4 {
-		nvidia,pins = "clk1_out_pw4";
-		nvidia,function = "extperiph1";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_ENABLE>;
-	};
-	clk2_out_pw5 {
-		nvidia,pins = "clk2_out_pw5";
-		nvidia,function = "extperiph2";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_ENABLE>;
-	};
-	uart3_txd_pw6 {
-		nvidia,pins = "uart3_txd_pw6";
-		nvidia,function = "uartc";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	uart3_rxd_pw7 {
-		nvidia,pins = "uart3_rxd_pw7";
-		nvidia,function = "uartc";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_ENABLE>;
-	};
-	spi2_sck_px2 {
-		nvidia,pins = "spi2_sck_px2";
-		nvidia,function = "gmi";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	spi1_mosi_px4 {
-		nvidia,pins = "spi1_mosi_px4";
-		nvidia,function = "spi1";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	spi1_sck_px5 {
-		nvidia,pins = "spi1_sck_px5";
-		nvidia,function = "spi1";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	spi1_cs0_n_px6 {
-		nvidia,pins = "spi1_cs0_n_px6";
-		nvidia,function = "spi1";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	spi1_miso_px7 {
-		nvidia,pins = "spi1_miso_px7";
-		nvidia,function = "spi1";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	ulpi_clk_py0 {
-		nvidia,pins = "ulpi_clk_py0";
-		nvidia,function = "uartd";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	ulpi_dir_py1 {
-		nvidia,pins = "ulpi_dir_py1";
-		nvidia,function = "uartd";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_ENABLE>;
-	};
-	ulpi_nxt_py2 {
-		nvidia,pins = "ulpi_nxt_py2";
-		nvidia,function = "uartd";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_ENABLE>;
-	};
-	ulpi_stp_py3 {
-		nvidia,pins = "ulpi_stp_py3";
-		nvidia,function = "uartd";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	sdmmc1_dat3_py4 {
-		nvidia,pins = "sdmmc1_dat3_py4";
-		nvidia,function = "sdmmc1";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	sdmmc1_dat2_py5 {
-		nvidia,pins = "sdmmc1_dat2_py5";
-		nvidia,function = "sdmmc1";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	sdmmc1_dat1_py6 {
-		nvidia,pins = "sdmmc1_dat1_py6";
-		nvidia,function = "sdmmc1";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	sdmmc1_dat0_py7 {
-		nvidia,pins = "sdmmc1_dat0_py7";
-		nvidia,function = "sdmmc1";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	sdmmc1_clk_pz0 {
-		nvidia,pins = "sdmmc1_clk_pz0";
-		nvidia,function = "sdmmc1";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	sdmmc1_cmd_pz1 {
-		nvidia,pins = "sdmmc1_cmd_pz1";
-		nvidia,function = "sdmmc1";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	lcd_sdin_pz2 {
-		nvidia,pins = "lcd_sdin_pz2";
-		nvidia,function = "displaya";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	lcd_wr_n_pz3 {
-		nvidia,pins = "lcd_wr_n_pz3";
-		nvidia,function = "displaya";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	lcd_sck_pz4 {
-		nvidia,pins = "lcd_sck_pz4";
-		nvidia,function = "displaya";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	sys_clk_req_pz5 {
-		nvidia,pins = "sys_clk_req_pz5";
-		nvidia,function = "sysclk";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	pwr_i2c_scl_pz6 {
-		nvidia,pins = "pwr_i2c_scl_pz6";
-		nvidia,function = "i2cpwr";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_ENABLE>;
-		nvidia,open-drain = <TEGRA_PIN_ENABLE>;
-	};
-	pwr_i2c_sda_pz7 {
-		nvidia,pins = "pwr_i2c_sda_pz7";
-		nvidia,function = "i2cpwr";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_ENABLE>;
-		nvidia,open-drain = <TEGRA_PIN_ENABLE>;
-	};
-	sdmmc4_dat0_paa0 {
-		nvidia,pins = "sdmmc4_dat0_paa0";
-		nvidia,function = "sdmmc4";
-		nvidia,pull = <TEGRA_PIN_PULL_UP>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_ENABLE>;
-		nvidia,io-reset = <TEGRA_PIN_DISABLE>;
-	};
-	sdmmc4_dat1_paa1 {
-		nvidia,pins = "sdmmc4_dat1_paa1";
-		nvidia,function = "sdmmc4";
-		nvidia,pull = <TEGRA_PIN_PULL_UP>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_ENABLE>;
-		nvidia,io-reset = <TEGRA_PIN_DISABLE>;
-	};
-	sdmmc4_dat2_paa2 {
-		nvidia,pins = "sdmmc4_dat2_paa2";
-		nvidia,function = "sdmmc4";
-		nvidia,pull = <TEGRA_PIN_PULL_UP>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_ENABLE>;
-		nvidia,io-reset = <TEGRA_PIN_DISABLE>;
-	};
-	sdmmc4_dat3_paa3 {
-		nvidia,pins = "sdmmc4_dat3_paa3";
-		nvidia,function = "sdmmc4";
-		nvidia,pull = <TEGRA_PIN_PULL_UP>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_ENABLE>;
-		nvidia,io-reset = <TEGRA_PIN_DISABLE>;
-	};
-	sdmmc4_dat4_paa4 {
-		nvidia,pins = "sdmmc4_dat4_paa4";
-		nvidia,function = "sdmmc4";
-		nvidia,pull = <TEGRA_PIN_PULL_UP>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_ENABLE>;
-		nvidia,io-reset = <TEGRA_PIN_DISABLE>;
-	};
-	sdmmc4_dat5_paa5 {
-		nvidia,pins = "sdmmc4_dat5_paa5";
-		nvidia,function = "sdmmc4";
-		nvidia,pull = <TEGRA_PIN_PULL_UP>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_ENABLE>;
-		nvidia,io-reset = <TEGRA_PIN_DISABLE>;
-	};
-	sdmmc4_dat6_paa6 {
-		nvidia,pins = "sdmmc4_dat6_paa6";
-		nvidia,function = "sdmmc4";
-		nvidia,pull = <TEGRA_PIN_PULL_UP>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_ENABLE>;
-		nvidia,io-reset = <TEGRA_PIN_DISABLE>;
-	};
-	sdmmc4_dat7_paa7 {
-		nvidia,pins = "sdmmc4_dat7_paa7";
-		nvidia,function = "sdmmc4";
-		nvidia,pull = <TEGRA_PIN_PULL_UP>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_ENABLE>;
-		nvidia,io-reset = <TEGRA_PIN_DISABLE>;
-	};
-	pbb0 {
-		nvidia,pins = "pbb0";
-		nvidia,function = "i2s4";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	cam_i2c_scl_pbb1 {
-		nvidia,pins = "cam_i2c_scl_pbb1";
-		nvidia,function = "i2c3";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-		nvidia,open-drain = <TEGRA_PIN_DISABLE>;
-	};
-	cam_i2c_sda_pbb2 {
-		nvidia,pins = "cam_i2c_sda_pbb2";
-		nvidia,function = "i2c3";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-		nvidia,open-drain = <TEGRA_PIN_DISABLE>;
-	};
-	pbb3 {
-		nvidia,pins = "pbb3";
-		nvidia,function = "vgp3";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	pbb4 {
-		nvidia,pins = "pbb4";
-		nvidia,function = "vgp4";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	pbb5 {
-		nvidia,pins = "pbb5";
-		nvidia,function = "vgp5";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	pbb6 {
-		nvidia,pins = "pbb6";
-		nvidia,function = "vgp6";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	pbb7 {
-		nvidia,pins = "pbb7";
-		nvidia,function = "i2s4";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	cam_mclk_pcc0 {
-		nvidia,pins = "cam_mclk_pcc0";
-		nvidia,function = "vi_alt3";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_ENABLE>;
-	};
-	pcc1 {
-		nvidia,pins = "pcc1";
-		nvidia,function = "i2s4";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_ENABLE>;
-	};
-	pcc2 {
-		nvidia,pins = "pcc2";
-		nvidia,function = "i2s4";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_ENABLE>;
-	};
-	sdmmc4_rst_n_pcc3 {
-		nvidia,pins = "sdmmc4_rst_n_pcc3";
-		nvidia,function = "sdmmc4";
-		nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_ENABLE>;
-		nvidia,io-reset = <TEGRA_PIN_DISABLE>;
-	};
-	sdmmc4_clk_pcc4 {
-		nvidia,pins = "sdmmc4_clk_pcc4";
-		nvidia,function = "sdmmc4";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_ENABLE>;
-		nvidia,io-reset = <TEGRA_PIN_DISABLE>;
-	};
-	clk2_req_pcc5 {
-		nvidia,pins = "clk2_req_pcc5";
-		nvidia,function = "dap";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	pex_l2_rst_n_pcc6 {
-		nvidia,pins = "pex_l2_rst_n_pcc6";
-		nvidia,function = "pcie";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	pex_l2_clkreq_n_pcc7 {
-		nvidia,pins = "pex_l2_clkreq_n_pcc7";
-		nvidia,function = "pcie";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	pex_l0_prsnt_n_pdd0 {
-		nvidia,pins = "pex_l0_prsnt_n_pdd0";
-		nvidia,function = "pcie";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	pex_l0_rst_n_pdd1 {
-		nvidia,pins = "pex_l0_rst_n_pdd1";
-		nvidia,function = "pcie";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	pex_l0_clkreq_n_pdd2 {
-		nvidia,pins = "pex_l0_clkreq_n_pdd2";
-		nvidia,function = "pcie";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	pex_wake_n_pdd3 {
-		nvidia,pins = "pex_wake_n_pdd3";
-		nvidia,function = "pcie";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	pex_l1_prsnt_n_pdd4 {
-		nvidia,pins = "pex_l1_prsnt_n_pdd4";
-		nvidia,function = "pcie";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	pex_l1_rst_n_pdd5 {
-		nvidia,pins = "pex_l1_rst_n_pdd5";
-		nvidia,function = "pcie";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	pex_l1_clkreq_n_pdd6 {
-		nvidia,pins = "pex_l1_clkreq_n_pdd6";
-		nvidia,function = "pcie";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	pex_l2_prsnt_n_pdd7 {
-		nvidia,pins = "pex_l2_prsnt_n_pdd7";
-		nvidia,function = "pcie";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	clk3_out_pee0 {
-		nvidia,pins = "clk3_out_pee0";
-		nvidia,function = "extperiph3";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	clk3_req_pee1 {
-		nvidia,pins = "clk3_req_pee1";
-		nvidia,function = "dev3";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_ENABLE>;
-	};
-	clk1_req_pee2 {
-		nvidia,pins = "clk1_req_pee2";
-		nvidia,function = "dap";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_ENABLE>;
-	};
-	hdmi_cec_pee3 {
-		nvidia,pins = "hdmi_cec_pee3";
-		nvidia,function = "cec";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_DISABLE>;
-		nvidia,enable-input = <TEGRA_PIN_ENABLE>;
-		nvidia,open-drain = <TEGRA_PIN_DISABLE>;
-	};
-	owr {
-		nvidia,pins = "owr";
-		nvidia,function = "owr";
-		nvidia,pull = <TEGRA_PIN_PULL_NONE>;
-		nvidia,tristate = <TEGRA_PIN_ENABLE>;
-		nvidia,enable-input = <TEGRA_PIN_DISABLE>;
-	};
-	drive_groups {
-		nvidia,pins = "drive_gma",
-			      "drive_gmb",
-			      "drive_gmc",
-			      "drive_gmd";
-		nvidia,pull-down-strength = <9>;
-		nvidia,pull-up-strength = <9>;
-		nvidia,slew-rate-rising = <TEGRA_PIN_SLEW_RATE_SLOWEST>;
-		nvidia,slew-rate-falling = <TEGRA_PIN_SLEW_RATE_SLOWEST>;
-	};
-};
 
 &emc_icc_dvfs_opp_table {
-	/delete-node/ opp@900000000,1350;
+	/delete-node/ opp-900000000-1350;
 };
 
 &emc_bw_dfs_opp_table {
-	/delete-node/ opp@900000000;
+	/delete-node/ opp-900000000;
 };
diff --git a/arch/arm/boot/dts/tegra30-pegatron-chagall.dts b/arch/arm/boot/dts/tegra30-pegatron-chagall.dts
new file mode 100644
index 000000000000..7c81f0205549
--- /dev/null
+++ b/arch/arm/boot/dts/tegra30-pegatron-chagall.dts
@@ -0,0 +1,2861 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include <dt-bindings/input/gpio-keys.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/thermal/thermal.h>
+
+#include "tegra30.dtsi"
+#include "tegra30-cpu-opp.dtsi"
+#include "tegra30-cpu-opp-microvolt.dtsi"
+#include "tegra30-asus-lvds-display.dtsi"
+
+/ {
+	model = "Pegatron Chagall";
+	compatible = "pegatron,chagall", "nvidia,tegra30";
+	chassis-type = "tablet";
+
+	aliases {
+		mmc0 = &sdmmc4; /* eMMC */
+		mmc1 = &sdmmc1; /* uSD slot */
+		mmc2 = &sdmmc3; /* WiFi */
+
+		rtc0 = &pmic;
+		rtc1 = "/rtc@7000e000";
+
+		display0 = &lcd;
+		display1 = &hdmi;
+
+		serial1 = &uartc; /* Bluetooth */
+		serial2 = &uartb; /* GPS */
+	};
+
+	/*
+	 * The decompressor and also some bootloaders rely on a
+	 * pre-existing /chosen node to be available to insert the
+	 * command line and merge other ATAGS info.
+	 */
+	chosen {};
+
+	memory@80000000 {
+		reg = <0x80000000 0x40000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		linux,cma@80000000 {
+			compatible = "shared-dma-pool";
+			alloc-ranges = <0x80000000 0x30000000>;
+			size = <0x10000000>; /* 256MiB */
+			linux,cma-default;
+			reusable;
+		};
+
+		ramoops@beb00000 {
+			compatible = "ramoops";
+			reg = <0xbeb00000 0x10000>; /* 64kB */
+			console-size = <0x8000>; /* 32kB */
+			record-size = <0x400>; /* 1kB */
+			ecc-size = <16>;
+		};
+
+		trustzone@bfe00000 {
+			reg = <0xbfe00000 0x200000>; /* 2MB */
+			no-map;
+		};
+	};
+
+	host1x@50000000 {
+		hdmi: hdmi@54280000 {
+			status = "okay";
+
+			hdmi-supply = <&hdmi_5v0_sys>;
+			pll-supply = <&vdd_1v8_vio>;
+			vdd-supply = <&vdd_3v3_sys>;
+
+			nvidia,hpd-gpio = <&gpio TEGRA_GPIO(N, 7) GPIO_ACTIVE_HIGH>;
+			nvidia,ddc-i2c-bus = <&hdmi_ddc>;
+		};
+	};
+
+	vde@6001a000 {
+		assigned-clocks = <&tegra_car TEGRA30_CLK_VDE>;
+		assigned-clock-parents = <&tegra_car TEGRA30_CLK_PLL_P>;
+		assigned-clock-rates = <408000000>;
+	};
+
+	pinmux@70000868 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&state_default>;
+
+		state_default: pinmux {
+			/* SDMMC1 pinmux */
+			sdmmc1_clk_pz0 {
+				nvidia,pins = "sdmmc1_clk_pz0";
+				nvidia,function = "sdmmc1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			sdmmc1_dat3_py4 {
+				nvidia,pins = "sdmmc1_dat3_py4",
+						"sdmmc1_dat2_py5",
+						"sdmmc1_dat1_py6",
+						"sdmmc1_dat0_py7",
+						"sdmmc1_cmd_pz1";
+				nvidia,function = "sdmmc1";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* SDMMC2 pinmux */
+			vi_d1_pd5 {
+				nvidia,pins = "vi_d1_pd5",
+						"vi_d2_pl0",
+						"vi_d3_pl1",
+						"vi_d5_pl3",
+						"vi_d7_pl5";
+				nvidia,function = "sdmmc2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			vi_d8_pl6 {
+				nvidia,pins = "vi_d8_pl6",
+						"vi_d9_pl7";
+				nvidia,function = "sdmmc2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,lock = <0>;
+				nvidia,ioreset = <0>;
+			};
+
+			/* SDMMC3 pinmux */
+			sdmmc3_clk_pa6 {
+				nvidia,pins = "sdmmc3_clk_pa6";
+				nvidia,function = "sdmmc3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			sdmmc3_cmd_pa7 {
+				nvidia,pins = "sdmmc3_cmd_pa7",
+						"sdmmc3_dat3_pb4",
+						"sdmmc3_dat2_pb5",
+						"sdmmc3_dat2_pb5",
+						"sdmmc3_dat1_pb6",
+						"sdmmc3_dat0_pb7",
+						"sdmmc3_dat5_pd0",
+						"sdmmc3_dat4_pd1",
+						"sdmmc3_dat6_pd3",
+						"sdmmc3_dat7_pd4";
+				nvidia,function = "sdmmc3";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* SDMMC4 pinmux */
+			sdmmc4_clk_pcc4 {
+				nvidia,pins = "sdmmc4_clk_pcc4";
+				nvidia,function = "sdmmc4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			sdmmc4_cmd_pt7 {
+				nvidia,pins = "sdmmc4_cmd_pt7",
+						"sdmmc4_dat0_paa0",
+						"sdmmc4_dat1_paa1",
+						"sdmmc4_dat2_paa2",
+						"sdmmc4_dat3_paa3",
+						"sdmmc4_dat4_paa4",
+						"sdmmc4_dat5_paa5",
+						"sdmmc4_dat6_paa6",
+						"sdmmc4_dat7_paa7";
+				nvidia,function = "sdmmc4";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* I2C pinmux */
+			gen1_i2c_scl_pc4 {
+				nvidia,pins = "gen1_i2c_scl_pc4",
+						"gen1_i2c_sda_pc5";
+				nvidia,function = "i2c1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,open-drain = <TEGRA_PIN_ENABLE>;
+				nvidia,lock = <0>;
+			};
+
+			gen2_i2c_scl_pt5 {
+				nvidia,pins = "gen2_i2c_scl_pt5",
+						"gen2_i2c_sda_pt6";
+				nvidia,function = "i2c2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,open-drain = <TEGRA_PIN_ENABLE>;
+				nvidia,lock = <0>;
+			};
+
+			cam_i2c_scl_pbb1 {
+				nvidia,pins = "cam_i2c_scl_pbb1",
+						"cam_i2c_sda_pbb2";
+				nvidia,function = "i2c3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,open-drain = <TEGRA_PIN_ENABLE>;
+				nvidia,lock = <0>;
+			};
+
+			ddc_scl_pv4 {
+				nvidia,pins = "ddc_scl_pv4",
+						"ddc_sda_pv5";
+				nvidia,function = "i2c4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,lock = <0>;
+			};
+
+			pwr_i2c_scl_pz6 {
+				nvidia,pins = "pwr_i2c_scl_pz6",
+						"pwr_i2c_sda_pz7";
+				nvidia,function = "i2cpwr";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,open-drain = <TEGRA_PIN_ENABLE>;
+				nvidia,lock = <0>;
+			};
+
+			/* HDMI-CEC pinmux */
+			hdmi_cec_pee3 {
+				nvidia,pins = "hdmi_cec_pee3";
+				nvidia,function = "cec";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,open-drain = <TEGRA_PIN_ENABLE>;
+				nvidia,lock = <0>;
+			};
+
+			/* UART-A */
+			ulpi_data0_po1 {
+				nvidia,pins = "ulpi_data0_po1";
+				nvidia,function = "uarta";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			ulpi_data1_po2 {
+				nvidia,pins = "ulpi_data1_po2",
+						"ulpi_data2_po3",
+						"ulpi_data3_po4",
+						"ulpi_data4_po5",
+						"ulpi_data5_po6",
+						"ulpi_data6_po7";
+				nvidia,function = "uarta";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			ulpi_data7_po0 {
+				nvidia,pins = "ulpi_data7_po0";
+				nvidia,function = "uarta";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			/* UART-B */
+			uart2_txd_pc2 {
+				nvidia,pins = "uart2_txd_pc2",
+						"uart2_rts_n_pj6";
+				nvidia,function = "uartb";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			uart2_rxd_pc3 {
+				nvidia,pins = "uart2_rxd_pc3",
+						"uart2_cts_n_pj5";
+				nvidia,function = "uartb";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* UART-C */
+			uart3_cts_n_pa1 {
+				nvidia,pins = "uart3_cts_n_pa1",
+						"uart3_rxd_pw7";
+				nvidia,function = "uartc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			uart3_rts_n_pc0 {
+				nvidia,pins = "uart3_rts_n_pc0",
+						"uart3_txd_pw6";
+				nvidia,function = "uartc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			/* UART-D */
+			ulpi_clk_py0 {
+				nvidia,pins = "ulpi_clk_py0",
+						"ulpi_stp_py3";
+				nvidia,function = "uartd";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			ulpi_dir_py1 {
+				nvidia,pins = "ulpi_dir_py1",
+						"ulpi_nxt_py2";
+				nvidia,function = "uartd";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* I2S pinmux */
+			dap1_fs_pn0 {
+				nvidia,pins = "dap1_fs_pn0",
+						"dap1_din_pn1",
+						"dap1_dout_pn2",
+						"dap1_sclk_pn3";
+				nvidia,function = "i2s0";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			dap2_fs_pa2 {
+				nvidia,pins = "dap2_fs_pa2",
+						"dap2_sclk_pa3",
+						"dap2_din_pa4",
+						"dap2_dout_pa5";
+				nvidia,function = "i2s1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			dap3_fs_pp0 {
+				nvidia,pins = "dap3_fs_pp0",
+						"dap3_din_pp1",
+						"dap3_dout_pp2",
+						"dap3_sclk_pp3";
+				nvidia,function = "i2s2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			dap4_fs_pp4 {
+				nvidia,pins = "dap4_fs_pp4",
+						"dap4_din_pp5",
+						"dap4_dout_pp6",
+						"dap4_sclk_pp7";
+				nvidia,function = "i2s3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			pcc2 {
+				nvidia,pins = "pcc2";
+				nvidia,function = "i2s4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* PCI-e pinmux */
+			pex_l2_rst_n_pcc6 {
+				nvidia,pins = "pex_l2_rst_n_pcc6",
+						"pex_l0_rst_n_pdd1",
+						"pex_l1_rst_n_pdd5";
+				nvidia,function = "pcie";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pex_l2_clkreq_n_pcc7 {
+				nvidia,pins = "pex_l2_clkreq_n_pcc7",
+						"pex_l0_prsnt_n_pdd0",
+						"pex_l0_clkreq_n_pdd2",
+						"pex_l2_prsnt_n_pdd7";
+				nvidia,function = "pcie";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			pex_wake_n_pdd3 {
+				nvidia,pins = "pex_wake_n_pdd3";
+				nvidia,function = "pcie";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			/* SPI pinmux */
+			spi1_mosi_px4 {
+				nvidia,pins = "spi1_mosi_px4",
+						"spi1_sck_px5",
+						"spi1_cs0_n_px6",
+						"spi1_miso_px7";
+				nvidia,function = "spi1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			spi2_cs1_n_pw2 {
+				nvidia,pins = "spi2_cs1_n_pw2",
+						"spi2_cs2_n_pw3";
+				nvidia,function = "spi2";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			spi2_sck_px2 {
+				nvidia,pins = "spi2_sck_px2";
+				nvidia,function = "gmi";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			gmi_a16_pj7 {
+				nvidia,pins = "gmi_a16_pj7",
+						"gmi_a19_pk7";
+				nvidia,function = "spi4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			gmi_a17_pb0 {
+				nvidia,pins = "gmi_a17_pb0",
+						"gmi_a18_pb1";
+				nvidia,function = "spi4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			spi2_mosi_px0 {
+				nvidia,pins = "spi2_mosi_px0";
+				nvidia,function = "spi6";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			spdif_out_pk5 {
+				nvidia,pins = "spdif_out_pk5";
+				nvidia,function = "spdif";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			spdif_in_pk6 {
+				nvidia,pins = "spdif_in_pk6";
+				nvidia,function = "spdif";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* Display A pinmux */
+			lcd_pwr0_pb2 {
+				nvidia,pins = "lcd_pwr0_pb2",
+						"lcd_pclk_pb3",
+						"lcd_pwr1_pc1",
+						"lcd_pwr2_pc6",
+						"lcd_d0_pe0",
+						"lcd_d1_pe1",
+						"lcd_d2_pe2",
+						"lcd_d3_pe3",
+						"lcd_d4_pe4",
+						"lcd_d5_pe5",
+						"lcd_d6_pe6",
+						"lcd_d7_pe7",
+						"lcd_d8_pf0",
+						"lcd_d9_pf1",
+						"lcd_d10_pf2",
+						"lcd_d11_pf3",
+						"lcd_d12_pf4",
+						"lcd_d13_pf5",
+						"lcd_d14_pf6",
+						"lcd_d15_pf7",
+						"lcd_de_pj1",
+						"lcd_hsync_pj3",
+						"lcd_vsync_pj4",
+						"lcd_d16_pm0",
+						"lcd_d17_pm1",
+						"lcd_d18_pm2",
+						"lcd_d19_pm3",
+						"lcd_d20_pm4",
+						"lcd_d21_pm5",
+						"lcd_d22_pm6",
+						"lcd_d23_pm7",
+						"lcd_cs0_n_pn4",
+						"lcd_sdout_pn5",
+						"lcd_dc0_pn6",
+						"lcd_sdin_pz2",
+						"lcd_wr_n_pz3",
+						"lcd_sck_pz4",
+						"lcd_cs1_n_pw0",
+						"lcd_m1_pw1";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			lcd_dc1_pd2 {
+				nvidia,pins = "lcd_dc1_pd2";
+				nvidia,function = "displaya";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			clk_32k_out_pa0 {
+				nvidia,pins = "clk_32k_out_pa0";
+				nvidia,function = "blink";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			/* KBC keys */
+			kb_row0_pr0 {
+				nvidia,pins = "kb_row0_pr0",
+						"kb_row1_pr1",
+						"kb_row2_pr2",
+						"kb_row3_pr3",
+						"kb_row8_ps0",
+						"kb_col0_pq0",
+						"kb_col1_pq1",
+						"kb_col2_pq2",
+						"kb_col3_pq3",
+						"kb_col4_pq4",
+						"kb_col5_pq5",
+						"kb_col7_pq7";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			kb_row4_pr4 {
+				nvidia,pins = "kb_row4_pr4",
+						"kb_row7_pr7",
+						"kb_row10_ps2",
+						"kb_row13_ps5";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_DOWN>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			kb_row11_ps3 {
+				nvidia,pins = "kb_row11_ps3",
+						"kb_row12_ps4",
+						"kb_row15_ps7";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			kb_row14_ps6 {
+				nvidia,pins = "kb_row14_ps6";
+				nvidia,function = "kbc";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			gmi_iordy_pi5 {
+				nvidia,pins = "gmi_iordy_pi5";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			vi_pclk_pt0 {
+				nvidia,pins = "vi_pclk_pt0";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,lock = <0>;
+				nvidia,ioreset = <0>;
+			};
+
+			pu1 {
+				nvidia,pins = "pu1";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pu2 {
+				nvidia,pins = "pu2";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			pv0 {
+				nvidia,pins = "pv0";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			pv1 {
+				nvidia,pins = "pv1";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			pcc1 {
+				nvidia,pins = "pcc1";
+				nvidia,function = "rsvd2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			sdmmc4_rst_n_pcc3 {
+				nvidia,pins = "sdmmc4_rst_n_pcc3";
+				nvidia,function = "rsvd2";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pv3 {
+				nvidia,pins = "pv3";
+				nvidia,function = "rsvd2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			vi_vsync_pd6 {
+				nvidia,pins = "vi_vsync_pd6",
+						"vi_hsync_pd7";
+				nvidia,function = "rsvd2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,lock = <0>;
+				nvidia,ioreset = <0>;
+			};
+
+			vi_d10_pt2 {
+				nvidia,pins = "vi_d10_pt2",
+						"vi_d0_pt4", "pbb0";
+				nvidia,function = "rsvd2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			vi_d11_pt3 {
+				nvidia,pins = "vi_d11_pt3";
+				nvidia,function = "rsvd2";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			pu0 {
+				nvidia,pins = "pu0";
+				nvidia,function = "rsvd4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			pu3 {
+				nvidia,pins = "pu3";
+				nvidia,function = "rsvd4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			pu6 {
+				nvidia,pins = "pu6";
+				nvidia,function = "rsvd4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			pex_l1_prsnt_n_pdd4 {
+				nvidia,pins = "pex_l1_prsnt_n_pdd4",
+						"pex_l1_clkreq_n_pdd6";
+				nvidia,function = "rsvd4";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			gmi_wait_pi7 {
+				nvidia,pins = "gmi_wait_pi7",
+						"gmi_cs0_n_pj0",
+						"gmi_cs1_n_pj2",
+						"gmi_cs4_n_pk2";
+				nvidia,function = "nand";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			gmi_ad0_pg0 {
+				nvidia,pins = "gmi_ad0_pg0",
+						"gmi_ad1_pg1",
+						"gmi_ad2_pg2",
+						"gmi_ad3_pg3",
+						"gmi_ad4_pg4",
+						"gmi_ad5_pg5",
+						"gmi_ad6_pg6",
+						"gmi_ad7_pg7",
+						"gmi_wr_n_pi0",
+						"gmi_oe_n_pi1",
+						"gmi_dqs_pi2",
+						"gmi_adv_n_pk0",
+						"gmi_clk_pk1";
+				nvidia,function = "nand";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			gmi_cs2_n_pk3 {
+				nvidia,pins = "gmi_cs2_n_pk3";
+				nvidia,function = "rsvd1";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			gmi_cs3_n_pk4 {
+				nvidia,pins = "gmi_cs3_n_pk4";
+				nvidia,function = "nand";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			gmi_ad10_ph2 {
+				nvidia,pins = "gmi_ad10_ph2",
+						"gmi_ad11_ph3",
+						"gmi_ad14_ph6";
+				nvidia,function = "nand";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			gmi_ad13_ph5 {
+				nvidia,pins = "gmi_ad13_ph5",
+						"gmi_ad12_ph4",
+						"gmi_cs7_n_pi6";
+				nvidia,function = "nand";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			gmi_rst_n_pi4 {
+				nvidia,pins = "gmi_rst_n_pi4";
+				nvidia,function = "gmi";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			gmi_ad8_ph0 {
+				nvidia,pins = "gmi_ad8_ph0";
+				nvidia,function = "pwm0";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			gmi_ad9_ph1 {
+				nvidia,pins = "gmi_ad9_ph1";
+				nvidia,function = "pwm1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			gmi_wp_n_pc7 {
+				nvidia,pins = "gmi_wp_n_pc7";
+				nvidia,function = "gmi";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			gmi_cs6_n_pi3 {
+				nvidia,pins = "gmi_cs6_n_pi3";
+				nvidia,function = "sata";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			vi_d4_pl2 {
+				nvidia,pins = "vi_d4_pl2";
+				nvidia,function = "vi";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			vi_d6_pl4 {
+				nvidia,pins = "vi_d6_pl4";
+				nvidia,function = "vi";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+				nvidia,lock = <0>;
+				nvidia,ioreset = <0>;
+			};
+
+			vi_mclk_pt1 {
+				nvidia,pins = "vi_mclk_pt1";
+				nvidia,function = "vi";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* HDMI hot-plug-detect */
+			hdmi_int_pn7 {
+				nvidia,pins = "hdmi_int_pn7";
+				nvidia,function = "hdmi";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_ENABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			pu4 {
+				nvidia,pins = "pu4";
+				nvidia,function = "pwm1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pu5 {
+				nvidia,pins = "pu5";
+				nvidia,function = "pwm2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			jtag_rtck_pu7 {
+				nvidia,pins = "jtag_rtck_pu7";
+				nvidia,function = "rtck";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			crt_hsync_pv6 {
+				nvidia,pins = "crt_hsync_pv6",
+						"crt_vsync_pv7";
+				nvidia,function = "crt";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			clk1_out_pw4 {
+				nvidia,pins = "clk1_out_pw4";
+				nvidia,function = "extperiph1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			clk2_out_pw5 {
+				nvidia,pins = "clk2_out_pw5";
+				nvidia,function = "extperiph2";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			clk3_out_pee0 {
+				nvidia,pins = "clk3_out_pee0";
+				nvidia,function = "extperiph3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			sys_clk_req_pz5 {
+				nvidia,pins = "sys_clk_req_pz5";
+				nvidia,function = "sysclk";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pbb4 {
+				nvidia,pins = "pbb4";
+				nvidia,function = "vgp4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			pbb5 {
+				nvidia,pins = "pbb5";
+				nvidia,function = "vgp5";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			pbb6 {
+				nvidia,pins = "pbb6";
+				nvidia,function = "vgp6";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			clk1_req_pee2 {
+				nvidia,pins = "clk1_req_pee2";
+				nvidia,function = "dap";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			clk2_req_pcc5 {
+				nvidia,pins = "clk2_req_pcc5";
+				nvidia,function = "dap";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			clk3_req_pee1 {
+				nvidia,pins = "clk3_req_pee1";
+				nvidia,function = "dev3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			owr {
+				nvidia,pins = "owr";
+				nvidia,function = "owr";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			pv2 {
+				nvidia,pins = "pv2",
+						"kb_row5_pr5";
+				nvidia,function = "owr";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_DISABLE>;
+			};
+
+			pbb3 {
+				nvidia,pins = "pbb3";
+				nvidia,function = "vgp3";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			pbb7 {
+				nvidia,pins = "pbb7";
+				nvidia,function = "i2s4";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			cam_mclk_pcc0 {
+				nvidia,pins = "cam_mclk_pcc0";
+				nvidia,function = "vi_alt3";
+				nvidia,pull = <TEGRA_PIN_PULL_UP>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+			};
+
+			/* GPIO power/drive control */
+			drive_dap1 {
+				nvidia,pins = "drive_dap1",
+						"drive_dap2",
+						"drive_dbg",
+						"drive_at5",
+						"drive_gme",
+						"drive_ddc",
+						"drive_ao1",
+						"drive_uart3";
+				nvidia,high-speed-mode = <0>;
+				nvidia,schmitt = <TEGRA_PIN_ENABLE>;
+				nvidia,low-power-mode = <TEGRA_PIN_LP_DRIVE_DIV_1>;
+				nvidia,pull-down-strength = <31>;
+				nvidia,pull-up-strength = <31>;
+				nvidia,slew-rate-rising = <TEGRA_PIN_SLEW_RATE_FASTEST>;
+				nvidia,slew-rate-falling = <TEGRA_PIN_SLEW_RATE_FASTEST>;
+			};
+
+			drive_sdio1 {
+				nvidia,pins = "drive_sdio1";
+				nvidia,high-speed-mode = <0>;
+				nvidia,schmitt = <TEGRA_PIN_DISABLE>;
+				nvidia,pull-down-strength = <5>;
+				nvidia,pull-up-strength = <5>;
+				nvidia,slew-rate-rising = <TEGRA_PIN_SLEW_RATE_FAST>;
+				nvidia,slew-rate-falling = <TEGRA_PIN_SLEW_RATE_FAST>;
+			};
+
+			drive_sdio3 {
+				nvidia,pins = "drive_sdio3";
+				nvidia,high-speed-mode = <0>;
+				nvidia,schmitt = <TEGRA_PIN_DISABLE>;
+				nvidia,pull-down-strength = <46>;
+				nvidia,pull-up-strength = <42>;
+				nvidia,slew-rate-rising = <TEGRA_PIN_SLEW_RATE_FAST>;
+				nvidia,slew-rate-falling = <TEGRA_PIN_SLEW_RATE_FAST>;
+			};
+
+			drive_gma {
+				nvidia,pins = "drive_gma",
+						"drive_gmb",
+						"drive_gmc",
+						"drive_gmd";
+				nvidia,pull-down-strength = <9>;
+				nvidia,pull-up-strength = <9>;
+				nvidia,slew-rate-rising = <TEGRA_PIN_SLEW_RATE_SLOWEST>;
+				nvidia,slew-rate-falling = <TEGRA_PIN_SLEW_RATE_SLOWEST>;
+			};
+
+			drive_lcd2 {
+				nvidia,pins = "drive_lcd2";
+				nvidia,high-speed-mode = <0>;
+				nvidia,schmitt = <TEGRA_PIN_ENABLE>;
+				nvidia,low-power-mode = <TEGRA_PIN_LP_DRIVE_DIV_4>;
+				nvidia,pull-down-strength = <20>;
+				nvidia,pull-up-strength = <20>;
+				nvidia,slew-rate-rising = <TEGRA_PIN_SLEW_RATE_FASTEST>;
+				nvidia,slew-rate-falling = <TEGRA_PIN_SLEW_RATE_FASTEST>;
+			};
+		};
+	};
+
+	uartb: serial@70006040 {
+		compatible = "nvidia,tegra30-hsuart";
+		/delete-property/ reg-shift;
+		status = "okay";
+
+		/* Broadcom GPS BCM47511 */
+	};
+
+	uartc: serial@70006200 {
+		compatible = "nvidia,tegra30-hsuart";
+		/delete-property/ reg-shift;
+		status = "okay";
+
+		nvidia,adjust-baud-rates = <0 9600 100>,
+					   <9600 115200 200>,
+					   <1000000 4000000 136>;
+
+		/* Azurewave AW-AH663 BCM4330B1 */
+		bluetooth {
+			compatible = "brcm,bcm4330-bt";
+			max-speed = <4000000>;
+
+			clocks = <&tegra_pmc TEGRA_PMC_CLK_BLINK>;
+			clock-names = "txco";
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(U, 6) IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "host-wakeup";
+
+			device-wakeup-gpios = <&gpio TEGRA_GPIO(U, 1) GPIO_ACTIVE_HIGH>;
+			shutdown-gpios = <&gpio TEGRA_GPIO(U, 0) GPIO_ACTIVE_HIGH>;
+
+			vbat-supply  = <&vdd_3v3_sys>;
+			vddio-supply = <&vdd_1v8_vio>;
+		};
+	};
+
+	pwm: pwm@7000a000 {
+		status = "okay";
+	};
+
+	lcd_ddc: i2c@7000c000 {
+		status = "okay";
+		clock-frequency = <400000>;
+
+		/* Wolfson Microelectronics WM8903 audio codec */
+		wm8903: audio-codec@1a {
+			compatible = "wlf,wm8903";
+			reg = <0x1a>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(W, 3) IRQ_TYPE_EDGE_BOTH>;
+
+			gpio-controller;
+			#gpio-cells = <2>;
+
+			micdet-cfg = <0>;
+			micdet-delay = <100>;
+
+			gpio-cfg = <0xffffffff 0xffffffff 0 0xffffffff 0xffffffff>;
+
+			AVDD-supply  = <&vdd_1v8_vio>;
+			CPVDD-supply = <&vdd_1v8_vio>;
+			DBVDD-supply = <&vdd_1v8_vio>;
+			DCVDD-supply = <&vdd_1v8_vio>;
+		};
+	};
+
+	i2c2: i2c@7000c400 {
+		status = "okay";
+		clock-frequency = <400000>;
+
+		/* Atmel touchscreen */
+		touchscreen@4d {
+			compatible = "atmel,maxtouch";
+			reg = <0x4d>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(H, 4) IRQ_TYPE_EDGE_FALLING>;
+			reset-gpios = <&gpio TEGRA_GPIO(H, 6) GPIO_ACTIVE_LOW>;
+
+			vdda-supply = <&vdd_3v3_sys>;
+			vdd-supply  = <&vdd_3v3_sys>;
+		};
+	};
+
+	i2c3: i2c@7000c500 {
+		status = "okay";
+		clock-frequency = <400000>;
+
+		light-sensor@44 {
+			compatible = "isil,isl29023";
+			reg = <0x44>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(Q, 3) IRQ_TYPE_LEVEL_HIGH>;
+
+			vcc-supply = <&vdd_3v3_sen>;
+		};
+
+		/* AsahiKASEI AK8975 magnetometer sensor */
+		magnetometer@c {
+			compatible = "asahi-kasei,ak8975";
+			reg = <0x0c>;
+
+			vdd-supply = <&vdd_3v3_sen>;
+			vid-supply = <&vdd_1v8_vio>;
+
+			mount-matrix =   "0",  "1",  "0",
+					 "1",  "0",  "0",
+					 "0",  "0", "-1";
+		};
+
+		gyroscope@68 {
+			compatible = "invensense,mpu3050";
+			reg = <0x68>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(X, 1) IRQ_TYPE_EDGE_RISING>;
+
+			vdd-supply = <&vdd_3v3_sen>;
+			vlogic-supply = <&vdd_1v8_vio>;
+
+			mount-matrix =   "0",  "1",  "0",
+					 "1",  "0",  "0",
+					 "0",  "0", "-1";
+
+			/* External I2C interface */
+			i2c-gate {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				accelerometer@f {
+					compatible = "kionix,kxtf9";
+					reg = <0x0f>;
+
+					interrupt-parent = <&gpio>;
+					interrupts = <TEGRA_GPIO(L, 1) IRQ_TYPE_EDGE_RISING>;
+
+					vdd-supply = <&vdd_1v8_vio>;
+					vddio-supply = <&vdd_1v8_vio>;
+
+					mount-matrix =  "-1",  "0",  "0",
+							 "0",  "1",  "0",
+							 "0",  "0",  "1";
+				};
+			};
+		};
+	};
+
+	hdmi_ddc: i2c@7000c700 {
+		status = "okay";
+		clock-frequency = <93750>;
+	};
+
+	i2c5: i2c@7000d000 {
+		status = "okay";
+		clock-frequency = <400000>;
+
+		nct72: temperature-sensor@4c {
+			compatible = "onnn,nct1008";
+			reg = <0x4c>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(U, 5) IRQ_TYPE_EDGE_FALLING>;
+
+			vcc-supply = <&vdd_3v3_sys>;
+			#thermal-sensor-cells = <1>;
+		};
+
+		/* Texas Instruments TPS659110 PMIC */
+		pmic: pmic@2d {
+			compatible = "ti,tps65911";
+			reg = <0x2d>;
+
+			interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
+			#interrupt-cells = <2>;
+			interrupt-controller;
+			wakeup-source;
+
+			ti,en-gpio-sleep = <0 0 1 0 0 0 0 0 0>;
+			ti,system-power-controller;
+			ti,sleep-keep-ck32k;
+			ti,sleep-enable;
+
+			#gpio-cells = <2>;
+			gpio-controller;
+
+			vcc1-supply = <&vdd_5v0_sys>;
+			vcc2-supply = <&vdd_5v0_sys>;
+			vcc3-supply = <&vdd_1v8_vio>;
+			vcc4-supply = <&vdd_1v8_vio>;
+			vcc5-supply = <&vdd_5v0_sys>;
+			vcc6-supply = <&vddio_1v2_ddr>;
+			vcc7-supply = <&vdd_5v0_sys>;
+			vccio-supply = <&vdd_5v0_sys>;
+
+			pmic-sleep-hog {
+				gpio-hog;
+				gpios = <0 GPIO_ACTIVE_HIGH>,
+					<2 GPIO_ACTIVE_HIGH>,
+					<6 GPIO_ACTIVE_HIGH>,
+					<8 GPIO_ACTIVE_HIGH>;
+				output-high;
+			};
+
+			regulators {
+				/* VDD1 is not used by Chagall */
+
+				vddio_1v2_ddr: vdd2 {
+					regulator-name = "vddio_1v2_ddr";
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				vdd_cpu: vddctrl {
+					regulator-name = "vdd_cpu,vdd_sys";
+					regulator-min-microvolt = <600000>;
+					regulator-max-microvolt = <1400000>;
+					regulator-coupled-with = <&vdd_core>;
+					regulator-coupled-max-spread = <300000>;
+					regulator-max-step-microvolt = <100000>;
+					regulator-always-on;
+					regulator-boot-on;
+					ti,regulator-ext-sleep-control = <1>;
+
+					nvidia,tegra-cpu-regulator;
+				};
+
+				vdd_1v8_vio: vio {
+					regulator-name = "vdd_1v8_gen";
+					/* FIXME: eMMC won't work, if set to 1.8 V */
+					regulator-min-microvolt = <1500000>;
+					regulator-max-microvolt = <3300000>;
+					regulator-always-on;
+					regulator-boot-on;
+				};
+
+				/* eMMC VDD */
+				vcore_emmc: ldo1 {
+					regulator-name = "vdd_emmc_core";
+					regulator-min-microvolt = <1000000>;
+					regulator-max-microvolt = <3300000>;
+					regulator-always-on;
+				};
+
+				/* uSD slot VDD */
+				vdd_usd: ldo2 {
+					regulator-name = "vdd_usd";
+					regulator-min-microvolt = <3200000>;
+					regulator-max-microvolt = <3200000>;
+				};
+
+				/* uSD slot VDDIO */
+				vddio_usd: ldo3 {
+					regulator-name = "vddio_usd";
+					regulator-min-microvolt = <1900000>;
+					regulator-max-microvolt = <3200000>;
+				};
+
+				ldo4 {
+					regulator-name = "vdd_rtc";
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+					regulator-always-on;
+				};
+
+				ldo5 {
+					regulator-name = "vdd_1v3_cam_isp";
+					regulator-min-microvolt = <1300000>;
+					regulator-max-microvolt = <1300000>;
+				};
+
+				ldo6 {
+					regulator-name = "avdd_dsi_csi,pwrdet_mipi";
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+				};
+
+				ldo7 {
+					regulator-name = "vdd_pllm,x,u,a_p_c_s";
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+					regulator-always-on;
+					regulator-boot-on;
+					ti,regulator-ext-sleep-control = <8>;
+				};
+
+				ldo8 {
+					regulator-name = "vdd_ddr_hs";
+					regulator-min-microvolt = <1000000>;
+					regulator-max-microvolt = <1000000>;
+					regulator-always-on;
+					ti,regulator-ext-sleep-control = <8>;
+				};
+			};
+		};
+
+		vdd_core: core-regulator@60 {
+			compatible = "ti,tps62361";
+			reg = <0x60>;
+
+			regulator-name = "tps62361-vout";
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1770000>;
+			regulator-coupled-with = <&vdd_cpu>;
+			regulator-coupled-max-spread = <300000>;
+			regulator-max-step-microvolt = <100000>;
+			regulator-boot-on;
+			regulator-always-on;
+			ti,enable-vout-discharge;
+			ti,vsel0-state-high;
+			ti,vsel1-state-high;
+
+			nvidia,tegra-core-regulator;
+		};
+	};
+
+	vdd_5v0_sys: regulator-5v {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_5v0_sys";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vdd_3v3_sys: regulator-3v {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_3v3_sys";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vdd_pnl: regulator-panel {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_panel";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-enable-ramp-delay = <300000>;
+		gpio = <&gpio TEGRA_GPIO(W, 1) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_3v3_sys>;
+	};
+
+	vdd_3v3_sen: regulator-sensors {
+		compatible = "regulator-fixed";
+		regulator-name = "sen_3v3_en";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio TEGRA_GPIO(K, 5) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_3v3_sys>;
+	};
+
+	vdd_5v0_bl: regulator-bl {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_5v0_bl";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-boot-on;
+		gpio = <&gpio TEGRA_GPIO(C, 6) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_5v0_sys>;
+	};
+
+	hdmi_5v0_sys: regulator-hdmi {
+		compatible = "regulator-fixed";
+		regulator-name = "hdmi_5v0_sys";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio TEGRA_GPIO(P, 2) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_5v0_sys>;
+	};
+
+	vdd_vbus_usb1: regulator-usb1 {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_vbus_micro_usb";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio TEGRA_GPIO(DD, 3) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_5v0_sys>;
+	};
+
+	vdd_vbus_usb3: regulator-usb3 {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_vbus_typea_usb";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio TEGRA_GPIO(CC, 6) GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		vin-supply = <&vdd_5v0_sys>;
+	};
+
+	pmc@7000e400 {
+		status = "okay";
+		nvidia,invert-interrupt;
+		nvidia,suspend-mode = <2>;
+		nvidia,cpu-pwr-good-time = <2000>;
+		nvidia,cpu-pwr-off-time = <200>;
+		nvidia,core-pwr-good-time = <3845 3845>;
+		nvidia,core-pwr-off-time = <0>;
+		nvidia,core-power-req-active-high;
+		nvidia,sys-clock-req-active-high;
+		core-supply = <&vdd_core>;
+
+		/* Set DEV_OFF + PWR_OFF_SET bit in DCDC control register of TPS65911 PMIC  */
+		i2c-thermtrip {
+			nvidia,i2c-controller-id = <4>;
+			nvidia,bus-addr = <0x2d>;
+			nvidia,reg-addr = <0x3f>;
+			nvidia,reg-data = <0x81>;
+		};
+	};
+
+	memory-controller@7000f000 {
+		emc-timings-0 {
+			/* SAMSUNG K4P8G304EB FGC1 */
+			nvidia,ram-code = <0>;
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+
+				nvidia,emem-configuration = < 0x00020001 0xc0000010
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000003 0x00000001 0x00000002 0x00000004
+					0x00000001 0x00000000 0x00000002 0x00000002
+					0x02020001 0x00060402 0x73e30303 0x001f0000 >;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+
+				nvidia,emem-configuration = < 0x00010001 0xc0000010
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000003 0x00000001 0x00000002 0x00000004
+					0x00000001 0x00000000 0x00000002 0x00000002
+					0x02020001 0x00060402 0x72c30303 0x001f0000 >;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emem-configuration = < 0x00000001 0xc0000018
+					0x00000001 0x00000001 0x00000003 0x00000001
+					0x00000003 0x00000001 0x00000002 0x00000004
+					0x00000001 0x00000000 0x00000002 0x00000002
+					0x02020001 0x00060403 0x72430504 0x001f0000 >;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emem-configuration = < 0x00000003 0xc0000025
+					0x00000001 0x00000001 0x00000006 0x00000003
+					0x00000005 0x00000001 0x00000002 0x00000004
+					0x00000001 0x00000000 0x00000003 0x00000002
+					0x02030001 0x00070506 0x71e40a07 0x001f0000 >;
+			};
+
+			timing-400000000 {
+				clock-frequency = <400000000>;
+
+				nvidia,emem-configuration = < 0x00000006 0xc0000048
+					0x00000002 0x00000003 0x0000000c 0x00000007
+					0x00000009 0x00000001 0x00000002 0x00000006
+					0x00000001 0x00000000 0x00000004 0x00000004
+					0x04040001 0x000d090c 0x7026120d 0x001f0000 >;
+			};
+		};
+
+		emc-timings-1 {
+			/* ELPIDA EDB8132B2MA 8D_F */
+			nvidia,ram-code = <1>;
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+
+				nvidia,emem-configuration = < 0x00020001 0xc0000010
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000003 0x00000001 0x00000002 0x00000004
+					0x00000001 0x00000000 0x00000002 0x00000002
+					0x02020001 0x00060402 0x73e30303 0x001f0000 >;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+
+				nvidia,emem-configuration = < 0x00010001 0xc0000010
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000003 0x00000001 0x00000002 0x00000004
+					0x00000001 0x00000000 0x00000002 0x00000002
+					0x02020001 0x00060402 0x72c30303 0x001f0000 >;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emem-configuration = < 0x00000001 0xc0000018
+					0x00000001 0x00000001 0x00000003 0x00000001
+					0x00000003 0x00000001 0x00000002 0x00000004
+					0x00000001 0x00000000 0x00000002 0x00000002
+					0x02020001 0x00060403 0x72430504 0x001f0000 >;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emem-configuration = < 0x00000003 0xc0000025
+					0x00000001 0x00000001 0x00000006 0x00000003
+					0x00000005 0x00000001 0x00000002 0x00000004
+					0x00000001 0x00000000 0x00000003 0x00000002
+					0x02030001 0x00070506 0x71e40a07 0x001f0000 >;
+			};
+
+			timing-400000000 {
+				clock-frequency = <400000000>;
+
+				nvidia,emem-configuration = < 0x00000006 0xc0000048
+					0x00000002 0x00000003 0x0000000c 0x00000007
+					0x00000009 0x00000001 0x00000002 0x00000006
+					0x00000001 0x00000000 0x00000004 0x00000004
+					0x04040001 0x000d090c 0x7026120d 0x001f0000 >;
+			};
+		};
+
+		emc-timings-2 {
+			/* SAMSUNG K4P8G304EB FGC2 */
+			nvidia,ram-code = <2>;
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+
+				nvidia,emem-configuration = < 0x00020001 0xc0000010
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000003 0x00000001 0x00000002 0x00000004
+					0x00000001 0x00000000 0x00000002 0x00000002
+					0x02020001 0x00060402 0x73e30303 0x001f0000 >;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+
+				nvidia,emem-configuration = < 0x00010001 0xc0000010
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000003 0x00000001 0x00000002 0x00000004
+					0x00000001 0x00000000 0x00000002 0x00000002
+					0x02020001 0x00060402 0x72c30303 0x001f0000 >;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emem-configuration = < 0x00000001 0xc0000018
+					0x00000001 0x00000001 0x00000003 0x00000001
+					0x00000003 0x00000001 0x00000002 0x00000004
+					0x00000001 0x00000000 0x00000002 0x00000002
+					0x02020001 0x00060403 0x72430504 0x001f0000 >;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emem-configuration = < 0x00000003 0xc0000025
+					0x00000001 0x00000001 0x00000006 0x00000003
+					0x00000005 0x00000001 0x00000002 0x00000004
+					0x00000001 0x00000000 0x00000003 0x00000002
+					0x02030001 0x00070506 0x71e40a07 0x001f0000 >;
+			};
+
+			timing-533000000 {
+				clock-frequency = <533000000>;
+
+				nvidia,emem-configuration = < 0x00000008 0xc0000060
+					0x00000003 0x00000004 0x00000010 0x0000000a
+					0x0000000d 0x00000002 0x00000002 0x00000008
+					0x00000002 0x00000000 0x00000004 0x00000005
+					0x05040002 0x00110b10 0x70281811 0x001f0000 >;
+			};
+		};
+
+		emc-timings-3 {
+			/* HYNIX H9TCNNN8JDMMPR NGM */
+			nvidia,ram-code = <3>;
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+
+				nvidia,emem-configuration = < 0x00020001 0xc0000010
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000003 0x00000001 0x00000002 0x00000004
+					0x00000001 0x00000000 0x00000002 0x00000002
+					0x02020001 0x00060402 0x73e30303 0x001f0000 >;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+
+				nvidia,emem-configuration = < 0x00010001 0xc0000010
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000003 0x00000001 0x00000002 0x00000004
+					0x00000001 0x00000000 0x00000002 0x00000002
+					0x02020001 0x00060402 0x72c30303 0x001f0000 >;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emem-configuration = < 0x00000001 0xc0000018
+					0x00000001 0x00000001 0x00000003 0x00000001
+					0x00000003 0x00000001 0x00000002 0x00000004
+					0x00000001 0x00000000 0x00000002 0x00000002
+					0x02020001 0x00060403 0x72430504 0x001f0000 >;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emem-configuration = < 0x00000003 0xc0000025
+					0x00000001 0x00000001 0x00000006 0x00000003
+					0x00000005 0x00000001 0x00000002 0x00000004
+					0x00000001 0x00000000 0x00000003 0x00000002
+					0x02030001 0x00070506 0x71e40a07 0x001f0000 >;
+			};
+
+			timing-533000000 {
+				clock-frequency = <533000000>;
+
+				nvidia,emem-configuration = < 0x00000008 0xc0000060
+					0x00000003 0x00000004 0x00000010 0x0000000a
+					0x0000000d 0x00000002 0x00000002 0x00000008
+					0x00000002 0x00000000 0x00000004 0x00000005
+					0x05040002 0x00110b10 0x70281811 0x001f0000 >;
+			};
+		};
+	};
+
+	memory-controller@7000f400 {
+		emc-timings-0 {
+			/* SAMSUNG K4P8G304EB FGC1 */
+			nvidia,ram-code = <0>;
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x00010022>;
+				nvidia,emc-mode-2 = <0x00020001>;
+				nvidia,emc-mode-reset = <0x00000000>;
+				nvidia,emc-zcal-cnt-long = <0x00000009>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000001
+					0x00000003 0x00000002 0x00000002 0x00000004
+					0x00000004 0x00000001 0x00000005 0x00000002
+					0x00000002 0x00000001 0x00000001 0x00000000
+					0x00000001 0x00000003 0x00000001 0x0000000b
+					0x00000009 0x00000060 0x00000000 0x00000018
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000007 0x00000004 0x00000004
+					0x00000003 0x00000008 0x00000004 0x00000004
+					0x00000002 0x0000006b 0x00000004 0x00000004
+					0x00000000 0x00000000 0x00004282 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00100220 0x0800201c 0x00000000
+					0x77ffc004 0x01f1f008 0x00000000 0x00000007
+					0x08000068 0x08000000 0x00000802 0x00064000
+					0x0000000a 0x00090009 0xa0f10000 0x00000000
+					0x00000000 0x800001c5 0xe0000000 0xff00ff00 >;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x00010022>;
+				nvidia,emc-mode-2 = <0x00020001>;
+				nvidia,emc-mode-reset = <0x00000000>;
+				nvidia,emc-zcal-cnt-long = <0x00000009>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000003
+					0x00000006 0x00000002 0x00000002 0x00000004
+					0x00000004 0x00000001 0x00000005 0x00000002
+					0x00000002 0x00000001 0x00000001 0x00000000
+					0x00000001 0x00000003 0x00000001 0x0000000b
+					0x00000009 0x000000c0 0x00000000 0x00000030
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000007 0x00000008 0x00000008
+					0x00000003 0x00000008 0x00000004 0x00000004
+					0x00000002 0x000000d5 0x00000004 0x00000004
+					0x00000000 0x00000000 0x00004282 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00100220 0x0800201c 0x00000000
+					0x77ffc004 0x01f1f008 0x00000000 0x00000007
+					0x08000068 0x08000000 0x00000802 0x00064000
+					0x00000013 0x00090009 0xa0f10000 0x00000000
+					0x00000000 0x80000287 0xe0000000 0xff00ff00 >;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x00010022>;
+				nvidia,emc-mode-2 = <0x00020001>;
+				nvidia,emc-mode-reset = <0x00000000>;
+				nvidia,emc-zcal-cnt-long = <0x0000000a>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000006
+					0x0000000d 0x00000004 0x00000002 0x00000004
+					0x00000004 0x00000001 0x00000005 0x00000002
+					0x00000002 0x00000001 0x00000001 0x00000000
+					0x00000001 0x00000003 0x00000001 0x0000000b
+					0x00000009 0x00000181 0x00000000 0x00000060
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000007 0x0000000f 0x0000000f
+					0x00000003 0x00000008 0x00000004 0x00000004
+					0x00000002 0x000001a9 0x00000004 0x00000004
+					0x00000000 0x00000000 0x00004282 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00100220 0x0800201c 0x00000000
+					0x77ffc004 0x01f1f008 0x00000000 0x00000007
+					0x08000068 0x08000000 0x00000802 0x00064000
+					0x00000025 0x00090009 0xa0f10000 0x00000000
+					0x00000000 0x8000040b 0xe0000000 0xff00ff00 >;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x00010042>;
+				nvidia,emc-mode-2 = <0x00020001>;
+				nvidia,emc-mode-reset = <0x00000000>;
+				nvidia,emc-zcal-cnt-long = <0x00000013>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x0000000c
+					0x0000001a 0x00000008 0x00000003 0x00000005
+					0x00000004 0x00000001 0x00000006 0x00000003
+					0x00000003 0x00000002 0x00000002 0x00000000
+					0x00000001 0x00000003 0x00000001 0x0000000c
+					0x0000000a 0x00000303 0x00000000 0x000000c0
+					0x00000001 0x00000001 0x00000003 0x00000000
+					0x00000001 0x00000007 0x0000001d 0x0000001d
+					0x00000004 0x0000000b 0x00000005 0x00000004
+					0x00000002 0x00000351 0x00000004 0x00000006
+					0x00000000 0x00000000 0x00004282 0x004400a4
+					0x00008000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x000e0220 0x0800201c 0x00000000
+					0x77ffc004 0x01f1f008 0x00000000 0x00000007
+					0x08000068 0x08000000 0x00000802 0x00064000
+					0x0000004a 0x00090009 0xa0f10000 0x00000000
+					0x00000000 0x80000713 0xe0000000 0xff00ff00 >;
+			};
+
+			timing-400000000 {
+				clock-frequency = <400000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x00010082>;
+				nvidia,emc-mode-2 = <0x00020004>;
+				nvidia,emc-mode-reset = <0x00000000>;
+				nvidia,emc-zcal-cnt-long = <0x00000024>;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000017
+					0x00000033 0x00000010 0x00000007 0x00000007
+					0x00000007 0x00000002 0x0000000a 0x00000007
+					0x00000007 0x00000003 0x00000002 0x00000000
+					0x00000003 0x00000007 0x00000004 0x0000000d
+					0x0000000e 0x000005e9 0x00000000 0x0000017a
+					0x00000002 0x00000002 0x00000007 0x00000000
+					0x00000001 0x0000000c 0x00000038 0x00000038
+					0x00000006 0x00000014 0x00000009 0x00000004
+					0x00000002 0x00000680 0x00000000 0x00000006
+					0x00000000 0x00000000 0x00006282 0x001d0084
+					0x00008000 0x00034000 0x00034000 0x00034000
+					0x00034000 0x00034000 0x00034000 0x00034000
+					0x00034000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00038000 0x00038000 0x00038000
+					0x00038000 0x00080220 0x0800003d 0x00000000
+					0x77ffc004 0x01f1f408 0x00000000 0x00000007
+					0x08000068 0x08000000 0x00000802 0x00064000
+					0x00000090 0x000c000c 0xa0f10404 0x00000000
+					0x00000000 0x80000ce6 0xe0000000 0xff00ff88 >;
+			};
+		};
+
+		emc-timings-1 {
+			/* ELPIDA EDB8132B2MA 8D_F */
+			nvidia,ram-code = <1>;
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x00010022>;
+				nvidia,emc-mode-2 = <0x00020001>;
+				nvidia,emc-mode-reset = <0x00000000>;
+				nvidia,emc-zcal-cnt-long = <0x00000009>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000001
+					0x00000003 0x00000002 0x00000002 0x00000004
+					0x00000004 0x00000001 0x00000005 0x00000002
+					0x00000002 0x00000001 0x00000001 0x00000000
+					0x00000001 0x00000003 0x00000001 0x0000000b
+					0x0000000a 0x00000060 0x00000000 0x00000018
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000007 0x00000004 0x00000004
+					0x00000003 0x00000008 0x00000004 0x00000004
+					0x00000002 0x0000006b 0x00000004 0x00000004
+					0x00000000 0x00000000 0x00004282 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00100220 0x0800201c 0x00000000
+					0x77ffc004 0x01f1f008 0x00000000 0x00000007
+					0x08000068 0x08000000 0x00000802 0x00064000
+					0x0000000a 0x00090009 0xa0f10000 0x00000000
+					0x00000000 0x800001c5 0xe0000000 0xff00ff00 >;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x00010022>;
+				nvidia,emc-mode-2 = <0x00020001>;
+				nvidia,emc-mode-reset = <0x00000000>;
+				nvidia,emc-zcal-cnt-long = <0x00000009>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000003
+					0x00000006 0x00000002 0x00000002 0x00000004
+					0x00000004 0x00000001 0x00000005 0x00000002
+					0x00000002 0x00000001 0x00000001 0x00000000
+					0x00000001 0x00000003 0x00000001 0x0000000b
+					0x0000000a 0x000000c0 0x00000000 0x00000030
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000007 0x00000008 0x00000008
+					0x00000003 0x00000008 0x00000004 0x00000004
+					0x00000002 0x000000d5 0x00000004 0x00000004
+					0x00000000 0x00000000 0x00004282 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00100220 0x0800201c 0x00000000
+					0x77ffc004 0x01f1f008 0x00000000 0x00000007
+					0x08000068 0x08000000 0x00000802 0x00064000
+					0x00000013 0x00090009 0xa0f10000 0x00000000
+					0x00000000 0x80000287 0xe0000000 0xff00ff00 >;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x00010022>;
+				nvidia,emc-mode-2 = <0x00020001>;
+				nvidia,emc-mode-reset = <0x00000000>;
+				nvidia,emc-zcal-cnt-long = <0x0000000a>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000006
+					0x0000000d 0x00000004 0x00000002 0x00000004
+					0x00000004 0x00000001 0x00000005 0x00000002
+					0x00000002 0x00000001 0x00000001 0x00000000
+					0x00000001 0x00000003 0x00000001 0x0000000b
+					0x0000000a 0x00000181 0x00000000 0x00000060
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000007 0x0000000f 0x0000000f
+					0x00000003 0x00000008 0x00000004 0x00000004
+					0x00000002 0x000001a9 0x00000004 0x00000004
+					0x00000000 0x00000000 0x00004282 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00100220 0x0800201c 0x00000000
+					0x77ffc004 0x01f1f008 0x00000000 0x00000007
+					0x08000068 0x08000000 0x00000802 0x00064000
+					0x00000025 0x00090009 0xa0f10000 0x00000000
+					0x00000000 0x8000040b 0xe0000000 0xff00ff00 >;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x00010042>;
+				nvidia,emc-mode-2 = <0x00020001>;
+				nvidia,emc-mode-reset = <0x00000000>;
+				nvidia,emc-zcal-cnt-long = <0x00000013>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x0000000c
+					0x0000001a 0x00000008 0x00000003 0x00000005
+					0x00000004 0x00000001 0x00000006 0x00000003
+					0x00000003 0x00000002 0x00000002 0x00000000
+					0x00000001 0x00000003 0x00000001 0x0000000c
+					0x0000000a 0x00000303 0x00000000 0x000000c0
+					0x00000001 0x00000001 0x00000003 0x00000000
+					0x00000001 0x00000007 0x0000001d 0x0000001d
+					0x00000004 0x0000000b 0x00000005 0x00000004
+					0x00000002 0x00000351 0x00000004 0x00000006
+					0x00000000 0x00000000 0x00004282 0x004400a4
+					0x00008000 0x00070000 0x00070000 0x00070000
+					0x00070000 0x00070000 0x00070000 0x00070000
+					0x00070000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x000e0220 0x0800201c 0x00000000
+					0x77ffc004 0x01f1f008 0x00000000 0x00000007
+					0x08000068 0x08000000 0x00000802 0x00064000
+					0x0000004a 0x00090009 0xa0f10000 0x00000000
+					0x00000000 0x80000713 0xe0000000 0xff00ff00 >;
+			};
+
+			timing-400000000 {
+				clock-frequency = <400000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x00010082>;
+				nvidia,emc-mode-2 = <0x00020004>;
+				nvidia,emc-mode-reset = <0x00000000>;
+				nvidia,emc-zcal-cnt-long = <0x00000024>;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000017
+					0x00000033 0x00000010 0x00000007 0x00000007
+					0x00000007 0x00000002 0x0000000a 0x00000007
+					0x00000007 0x00000003 0x00000002 0x00000000
+					0x00000003 0x00000007 0x00000004 0x0000000d
+					0x0000000e 0x000005e9 0x00000000 0x0000017a
+					0x00000002 0x00000002 0x00000007 0x00000000
+					0x00000001 0x0000000c 0x00000038 0x00000038
+					0x00000006 0x00000014 0x00000009 0x00000004
+					0x00000002 0x00000680 0x00000000 0x00000004
+					0x00000000 0x00000000 0x00006282 0x001d0084
+					0x00008000 0x00034000 0x00034000 0x00034000
+					0x00034000 0x00034000 0x00034000 0x00034000
+					0x00034000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00048000 0x00048000 0x00048000
+					0x00048000 0x00060220 0x0800003d 0x00000000
+					0x77ffc004 0x01f1f408 0x00000000 0x00000007
+					0x08000068 0x08000000 0x00000802 0x00064000
+					0x00000090 0x000c000c 0xa0f10000 0x00000000
+					0x00000000 0x80000ce6 0xe0000000 0xff00ff88 >;
+			};
+		};
+
+		emc-timings-2 {
+			/* SAMSUNG K4P8G304EB FGC2 */
+			nvidia,ram-code = <2>;
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x00010022>;
+				nvidia,emc-mode-2 = <0x00020001>;
+				nvidia,emc-mode-reset = <0x00000000>;
+				nvidia,emc-zcal-cnt-long = <0x00000009>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000001
+					0x00000003 0x00000002 0x00000002 0x00000004
+					0x00000004 0x00000001 0x00000005 0x00000002
+					0x00000002 0x00000001 0x00000001 0x00000000
+					0x00000001 0x00000003 0x00000001 0x0000000b
+					0x0000000a 0x00000060 0x00000000 0x00000018
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000007 0x00000004 0x00000004
+					0x00000003 0x00000008 0x00000004 0x00000004
+					0x00000002 0x0000006b 0x00000004 0x00000004
+					0x00000000 0x00000000 0x00004282 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00100220 0x0800201c 0x00000000
+					0x77ffc004 0x01f1f008 0x00000000 0x00000007
+					0x08000068 0x08000000 0x00000802 0x00064000
+					0x0000000a 0x00090009 0xa0f10000 0x00000000
+					0x00000000 0x800001c5 0xe0000000 0xff00ff00 >;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x00010022>;
+				nvidia,emc-mode-2 = <0x00020001>;
+				nvidia,emc-mode-reset = <0x00000000>;
+				nvidia,emc-zcal-cnt-long = <0x00000009>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000003
+					0x00000006 0x00000002 0x00000002 0x00000004
+					0x00000004 0x00000001 0x00000005 0x00000002
+					0x00000002 0x00000001 0x00000001 0x00000000
+					0x00000001 0x00000003 0x00000001 0x0000000b
+					0x0000000a 0x000000c0 0x00000000 0x00000030
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000007 0x00000008 0x00000008
+					0x00000003 0x00000008 0x00000004 0x00000004
+					0x00000002 0x000000d5 0x00000004 0x00000004
+					0x00000000 0x00000000 0x00004282 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00100220 0x0800201c 0x00000000
+					0x77ffc004 0x01f1f008 0x00000000 0x00000007
+					0x08000068 0x08000000 0x00000802 0x00064000
+					0x00000013 0x00090009 0xa0f10000 0x00000000
+					0x00000000 0x80000287 0xe0000000 0xff00ff00 >;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x00010022>;
+				nvidia,emc-mode-2 = <0x00020001>;
+				nvidia,emc-mode-reset = <0x00000000>;
+				nvidia,emc-zcal-cnt-long = <0x0000000a>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000006
+					0x0000000d 0x00000004 0x00000002 0x00000004
+					0x00000004 0x00000001 0x00000005 0x00000002
+					0x00000002 0x00000001 0x00000001 0x00000000
+					0x00000001 0x00000003 0x00000001 0x0000000b
+					0x00000009 0x00000181 0x00000000 0x00000060
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000007 0x0000000f 0x0000000f
+					0x00000003 0x00000008 0x00000004 0x00000004
+					0x00000002 0x000001a9 0x00000004 0x00000004
+					0x00000000 0x00000000 0x00004282 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00100220 0x0800201c 0x00000000
+					0x77ffc004 0x01f1f008 0x00000000 0x00000007
+					0x08000068 0x08000000 0x00000802 0x00064000
+					0x00000025 0x00090009 0xa0f10000 0x00000000
+					0x00000000 0x8000040b 0xe0000000 0xff00ff00 >;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x00010042>;
+				nvidia,emc-mode-2 = <0x00020001>;
+				nvidia,emc-mode-reset = <0x00000000>;
+				nvidia,emc-zcal-cnt-long = <0x00000013>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x0000000c
+					0x0000001a 0x00000008 0x00000003 0x00000005
+					0x00000004 0x00000001 0x00000006 0x00000003
+					0x00000003 0x00000002 0x00000002 0x00000000
+					0x00000001 0x00000004 0x00000001 0x0000000c
+					0x0000000a 0x00000303 0x00000000 0x000000c0
+					0x00000001 0x00000001 0x00000003 0x00000000
+					0x00000001 0x00000007 0x0000001d 0x0000001d
+					0x00000004 0x0000000b 0x00000005 0x00000004
+					0x00000002 0x00000351 0x00000005 0x00000004
+					0x00000000 0x00000000 0x00004282 0x004400a4
+					0x00008000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x000e0220 0x0800201c 0x00000000
+					0x77ffc004 0x01f1f008 0x00000000 0x00000007
+					0x08000068 0x08000000 0x00000802 0x00064000
+					0x0000004a 0x00090009 0xa0f10000 0x00000000
+					0x00000000 0x80000713 0xe0000000 0xff00ff00 >;
+			};
+
+			timing-533000000 {
+				clock-frequency = <533000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x000100c2>;
+				nvidia,emc-mode-2 = <0x00020006>;
+				nvidia,emc-mode-reset = <0x00000000>;
+				nvidia,emc-zcal-cnt-long = <0x00000030>;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x0000001f
+					0x00000045 0x00000016 0x00000009 0x00000008
+					0x00000009 0x00000003 0x0000000d 0x00000009
+					0x00000009 0x00000005 0x00000003 0x00000000
+					0x00000004 0x0000000a 0x00000006 0x0000000d
+					0x00000010 0x000007df 0x00000000 0x000001f7
+					0x00000003 0x00000003 0x00000009 0x00000000
+					0x00000001 0x0000000f 0x0000004b 0x0000004b
+					0x00000008 0x0000001b 0x0000000c 0x00000004
+					0x00000002 0x000008aa 0x00000000 0x00000004
+					0x00000000 0x00000000 0x00006282 0xf0120091
+					0x00008000 0x007f8008 0x007f8008 0x007f8008
+					0x007f8008 0x007f8008 0x007f8008 0x007f8008
+					0x007f8008 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x0000000c 0x0000000c 0x0000000c
+					0x0000000c 0x00080220 0x0200003d 0x00000000
+					0x77ffc004 0x01f1f408 0x00000000 0x00000007
+					0x08000068 0x08000000 0x00000802 0x00064000
+					0x000000c0 0x000e000e 0xa0f10000 0x00000000
+					0x00000000 0x800010d9 0xf0000000 0xff00ff88 >;
+			};
+		};
+
+		emc-timings-3 {
+			/* HYNIX H9TCNNN8JDMMPR NGM */
+			nvidia,ram-code = <3>;
+
+			timing-25500000 {
+				clock-frequency = <25500000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x00010022>;
+				nvidia,emc-mode-2 = <0x00020001>;
+				nvidia,emc-mode-reset = <0x00000000>;
+				nvidia,emc-zcal-cnt-long = <0x00000009>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000001
+					0x00000003 0x00000002 0x00000002 0x00000004
+					0x00000004 0x00000001 0x00000005 0x00000002
+					0x00000002 0x00000001 0x00000001 0x00000000
+					0x00000001 0x00000003 0x00000001 0x0000000b
+					0x0000000a 0x00000060 0x00000000 0x00000018
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000007 0x00000004 0x00000004
+					0x00000003 0x00000008 0x00000004 0x00000004
+					0x00000002 0x0000006b 0x00000004 0x00000004
+					0x00000000 0x00000000 0x00004282 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00100220 0x0800201c 0x00000000
+					0x77ffc004 0x01f1f008 0x00000000 0x00000007
+					0x08000068 0x08000000 0x00000802 0x00064000
+					0x0000000a 0x00090009 0xa0f10000 0x00000000
+					0x00000000 0x800001c5 0xe0000000 0xff00ff00 >;
+			};
+
+			timing-51000000 {
+				clock-frequency = <51000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x00010022>;
+				nvidia,emc-mode-2 = <0x00020001>;
+				nvidia,emc-mode-reset = <0x00000000>;
+				nvidia,emc-zcal-cnt-long = <0x00000009>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000003
+					0x00000006 0x00000002 0x00000002 0x00000004
+					0x00000004 0x00000001 0x00000005 0x00000002
+					0x00000002 0x00000001 0x00000001 0x00000000
+					0x00000001 0x00000003 0x00000001 0x0000000b
+					0x0000000a 0x000000c0 0x00000000 0x00000030
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000007 0x00000008 0x00000008
+					0x00000003 0x00000008 0x00000004 0x00000004
+					0x00000002 0x000000d5 0x00000004 0x00000004
+					0x00000000 0x00000000 0x00004282 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00100220 0x0800201c 0x00000000
+					0x77ffc004 0x01f1f008 0x00000000 0x00000007
+					0x08000068 0x08000000 0x00000802 0x00064000
+					0x00000013 0x00090009 0xa0f10000 0x00000000
+					0x00000000 0x80000287 0xe0000000 0xff00ff00 >;
+			};
+
+			timing-102000000 {
+				clock-frequency = <102000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x00010022>;
+				nvidia,emc-mode-2 = <0x00020001>;
+				nvidia,emc-mode-reset = <0x00000000>;
+				nvidia,emc-zcal-cnt-long = <0x0000000a>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x00000006
+					0x0000000d 0x00000004 0x00000002 0x00000004
+					0x00000004 0x00000001 0x00000005 0x00000002
+					0x00000002 0x00000001 0x00000001 0x00000000
+					0x00000001 0x00000003 0x00000001 0x0000000b
+					0x0000000a 0x00000181 0x00000000 0x00000060
+					0x00000001 0x00000001 0x00000002 0x00000000
+					0x00000001 0x00000007 0x0000000f 0x0000000f
+					0x00000003 0x00000008 0x00000004 0x00000004
+					0x00000002 0x000001a9 0x00000004 0x00000004
+					0x00000000 0x00000000 0x00004282 0x007800a4
+					0x00008000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x000fc000 0x000fc000 0x000fc000
+					0x000fc000 0x00100220 0x0800201c 0x00000000
+					0x77ffc004 0x01f1f008 0x00000000 0x00000007
+					0x08000068 0x08000000 0x00000802 0x00064000
+					0x00000025 0x00090009 0xa0f10000 0x00000000
+					0x00000000 0x8000040b 0xe0000000 0xff00ff00 >;
+			};
+
+			timing-204000000 {
+				clock-frequency = <204000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x00010042>;
+				nvidia,emc-mode-2 = <0x00020001>;
+				nvidia,emc-mode-reset = <0x00000000>;
+				nvidia,emc-zcal-cnt-long = <0x00000013>;
+				nvidia,emc-cfg-dyn-self-ref;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x0000000c
+					0x0000001a 0x00000008 0x00000003 0x00000005
+					0x00000004 0x00000001 0x00000006 0x00000003
+					0x00000003 0x00000002 0x00000002 0x00000000
+					0x00000001 0x00000003 0x00000001 0x0000000c
+					0x0000000b 0x00000303 0x00000000 0x000000c0
+					0x00000001 0x00000001 0x00000003 0x00000000
+					0x00000001 0x00000007 0x0000001d 0x0000001d
+					0x00000004 0x0000000b 0x00000005 0x00000004
+					0x00000002 0x00000351 0x00000004 0x00000006
+					0x00000000 0x00000000 0x00004282 0x004400a4
+					0x00008000 0x00072000 0x00072000 0x00072000
+					0x00072000 0x00072000 0x00072000 0x00072000
+					0x00072000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00080000 0x00080000 0x00080000
+					0x00080000 0x000e0220 0x0800201c 0x00000000
+					0x77ffc004 0x01f1f008 0x00000000 0x00000007
+					0x08000068 0x08000000 0x00000802 0x00064000
+					0x0000004a 0x00090009 0xa0f10000 0x00000000
+					0x00000000 0x80000713 0xd0000000 0xff00ff00 >;
+			};
+
+			timing-533000000 {
+				clock-frequency = <533000000>;
+
+				nvidia,emc-auto-cal-interval = <0x001fffff>;
+				nvidia,emc-mode-1 = <0x000100c2>;
+				nvidia,emc-mode-2 = <0x00020006>;
+				nvidia,emc-mode-reset = <0x00000000>;
+				nvidia,emc-zcal-cnt-long = <0x00000030>;
+				nvidia,emc-cfg-periodic-qrst;
+
+				nvidia,emc-configuration =  < 0x0000001f
+					0x00000045 0x00000016 0x00000009 0x00000008
+					0x00000009 0x00000003 0x0000000d 0x00000009
+					0x00000009 0x00000005 0x00000003 0x00000000
+					0x00000004 0x00000009 0x00000006 0x0000000d
+					0x00000010 0x000007df 0x00000000 0x000001f7
+					0x00000003 0x00000003 0x00000009 0x00000000
+					0x00000001 0x0000000f 0x0000004b 0x0000004b
+					0x00000008 0x0000001b 0x0000000c 0x00000004
+					0x00000002 0x000008aa 0x00000000 0x00000006
+					0x00000000 0x00000000 0x00006282 0xf0120091
+					0x00008000 0x0000000a 0x0000000a 0x0000000a
+					0x0000000a 0x0000000a 0x0000000a 0x0000000a
+					0x0000000a 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x00000000 0x00000000 0x00000000
+					0x00000000 0x0000000c 0x0000000c 0x0000000c
+					0x0000000c 0x000a0220 0x0800003d 0x00000000
+					0x77ffc004 0x01f1f408 0x00000000 0x00000007
+					0x08000068 0x08000000 0x00000802 0x00064000
+					0x000000c0 0x000e000e 0xa0f10000 0x00000000
+					0x00000000 0x800010d9 0xe0000000 0xff00ff88 >;
+			};
+		};
+	};
+
+	hda@70030000 {
+		status = "okay";
+	};
+
+	ahub@70080000 {
+		i2s@70080400 { /* i2s1 */
+			status = "okay";
+		};
+
+		/* BT SCO */
+		i2s@70080600 { /* i2s3 */
+			status = "okay";
+		};
+	};
+
+	sdmmc1: mmc@78000000 {
+		status = "okay";
+
+		cd-gpios = <&gpio TEGRA_GPIO(I, 5) GPIO_ACTIVE_LOW>;
+		bus-width = <4>;
+
+		vmmc-supply = <&vdd_usd>; /* ldo2 */
+		vqmmc-supply = <&vddio_usd>; /* ldo3 */
+	};
+
+	brcm_wifi_pwrseq: wifi-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+
+		clocks = <&tegra_pmc TEGRA_PMC_CLK_BLINK>;
+		clock-names = "ext_clock";
+
+		reset-gpios = <&gpio TEGRA_GPIO(D, 3) GPIO_ACTIVE_LOW>;
+		post-power-on-delay-ms = <300>;
+		power-off-delay-us = <300>;
+	};
+
+	sdmmc3: mmc@78000400 {
+		status = "okay";
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		assigned-clocks = <&tegra_car TEGRA30_CLK_SDMMC3>;
+		assigned-clock-parents = <&tegra_car TEGRA30_CLK_PLL_C>;
+		assigned-clock-rates = <50000000>;
+
+		max-frequency = <50000000>;
+		keep-power-in-suspend;
+		bus-width = <4>;
+		non-removable;
+
+		mmc-pwrseq = <&brcm_wifi_pwrseq>;
+		vmmc-supply = <&vdd_3v3_sys>;
+		vqmmc-supply = <&vdd_1v8_vio>;
+
+		/* Azurewave AW-AH663 BCM4330B1 */
+		wifi@1 {
+			compatible = "brcm,bcm4329-fmac";
+			reg = <1>;
+
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(O, 4) IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "host-wake";
+		};
+	};
+
+	sdmmc4: mmc@78000600 {
+		status = "okay";
+		bus-width = <8>;
+		vmmc-supply = <&vcore_emmc>;
+		vqmmc-supply = <&vdd_1v8_vio>;
+		non-removable;
+	};
+
+	usb@7d000000 {
+		compatible = "nvidia,tegra30-udc";
+		status = "okay";
+		dr_mode = "otg";
+		vbus-supply = <&vdd_vbus_usb1>;
+	};
+
+	usb-phy@7d000000 {
+		status = "okay";
+		dr_mode = "otg";
+		nvidia,hssync-start-delay = <0>;
+		nvidia,xcvr-lsfslew = <2>;
+		nvidia,xcvr-lsrslew = <2>;
+	};
+
+	usb@7d008000 {
+		status = "okay";
+	};
+
+	usb-phy@7d008000 {
+		status = "okay";
+		vbus-supply = <&vdd_vbus_usb3>;
+	};
+
+	mains: ac-adapter-detect {
+		compatible = "gpio-charger";
+		charger-type = "mains";
+		gpios = <&gpio TEGRA_GPIO(V, 1) GPIO_ACTIVE_HIGH>;
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+
+		enable-gpios = <&gpio TEGRA_GPIO(H, 2) GPIO_ACTIVE_HIGH>;
+		power-supply = <&vdd_5v0_bl>;
+		pwms = <&pwm 0 5000000>;
+
+		brightness-levels = <1 255>;
+		num-interpolated-steps = <254>;
+		default-brightness-level = <15>;
+	};
+
+	/* PMIC has a built-in 32KHz oscillator which is used by PMC */
+	clk32k_in: clock-32k {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		clock-output-names = "pmic-oscillator";
+	};
+
+	cpus {
+		cpu0: cpu@0 {
+			cpu-supply = <&vdd_cpu>;
+			operating-points-v2 = <&cpu0_opp_table>;
+			#cooling-cells = <2>;
+		};
+		cpu1: cpu@1 {
+			cpu-supply = <&vdd_cpu>;
+			operating-points-v2 = <&cpu0_opp_table>;
+			#cooling-cells = <2>;
+		};
+		cpu2: cpu@2 {
+			cpu-supply = <&vdd_cpu>;
+			operating-points-v2 = <&cpu0_opp_table>;
+			#cooling-cells = <2>;
+		};
+		cpu3: cpu@3 {
+			cpu-supply = <&vdd_cpu>;
+			operating-points-v2 = <&cpu0_opp_table>;
+			#cooling-cells = <2>;
+		};
+	};
+
+	display-panel {
+		compatible = "panel-lvds";
+
+		width-mm = <217>;
+		height-mm = <136>;
+
+		data-mapping = "jeida-24";
+
+		panel-timing {
+			/* 1280x800@60Hz */
+			clock-frequency = <68000000>;
+			hactive = <1280>;
+			vactive = <800>;
+			hfront-porch = <48>;
+			hback-porch = <18>;
+			hsync-len = <30>;
+			vsync-len = <5>;
+			vfront-porch = <3>;
+			vback-porch = <12>;
+		};
+	};
+
+	extcon-keys {
+		compatible = "gpio-keys";
+		interrupt-parent = <&gpio>;
+
+		switch-dock-insert {
+			label = "Chagall Dock";
+			gpios = <&gpio TEGRA_GPIO(S, 4) GPIO_ACTIVE_LOW>;
+			linux,input-type = <EV_SW>;
+			linux,code = <SW_DOCK>;
+			debounce-interval = <10>;
+			wakeup-event-action = <EV_ACT_ASSERTED>;
+			wakeup-source;
+		};
+
+		switch-lineout-detect {
+			label = "Audio dock line-out detect";
+			gpios = <&gpio TEGRA_GPIO(S, 3) GPIO_ACTIVE_LOW>;
+			linux,input-type = <EV_SW>;
+			linux,code = <SW_LINEOUT_INSERT>;
+			debounce-interval = <10>;
+			wakeup-event-action = <EV_ACT_ASSERTED>;
+			wakeup-source;
+		};
+	};
+
+	firmware {
+		trusted-foundations {
+			compatible = "tlm,trusted-foundations";
+			tlm,version-major = <2>;
+			tlm,version-minor = <8>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		interrupt-parent = <&gpio>;
+
+		key-power {
+			label = "Power";
+			gpios = <&gpio TEGRA_GPIO(V, 0) GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_POWER>;
+			debounce-interval = <10>;
+			wakeup-event-action = <EV_ACT_ASSERTED>;
+			wakeup-source;
+		};
+
+		key-volume-up {
+			label = "Volume Up";
+			gpios = <&gpio TEGRA_GPIO(Q, 0) GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+			debounce-interval = <10>;
+			wakeup-event-action = <EV_ACT_ASSERTED>;
+			wakeup-source;
+		};
+
+		key-volume-down {
+			label = "Volume Down";
+			gpios = <&gpio TEGRA_GPIO(Q, 1) GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEDOWN>;
+			debounce-interval = <10>;
+			wakeup-event-action = <EV_ACT_ASSERTED>;
+			wakeup-source;
+		};
+	};
+
+	haptic-feedback {
+		compatible = "gpio-vibrator";
+		enable-gpios = <&gpio TEGRA_GPIO(U, 4) GPIO_ACTIVE_HIGH>;
+		vcc-supply = <&vdd_3v3_sys>;
+	};
+
+	sound {
+		compatible = "pegatron,tegra-audio-wm8903-chagall",
+			     "nvidia,tegra-audio-wm8903";
+		nvidia,model = "Pegatron Chagall WM8903";
+
+		nvidia,audio-routing =
+			"Headphone Jack", "HPOUTR",
+			"Headphone Jack", "HPOUTL",
+			"Int Spk", "ROP",
+			"Int Spk", "RON",
+			"Int Spk", "LOP",
+			"Int Spk", "LON",
+			"IN1R", "Mic Jack",
+			"DMICDAT", "Int Mic";
+
+		nvidia,i2s-controller = <&tegra_i2s1>;
+		nvidia,audio-codec = <&wm8903>;
+
+		nvidia,spkr-en-gpios = <&wm8903 2 GPIO_ACTIVE_HIGH>;
+		nvidia,hp-det-gpios = <&gpio TEGRA_GPIO(W, 2) GPIO_ACTIVE_LOW>;
+		nvidia,headset;
+
+		clocks = <&tegra_car TEGRA30_CLK_PLL_A>,
+			 <&tegra_car TEGRA30_CLK_PLL_A_OUT0>,
+			 <&tegra_pmc TEGRA_PMC_CLK_OUT_1>;
+		clock-names = "pll_a", "pll_a_out0", "mclk";
+
+		assigned-clocks = <&tegra_car TEGRA30_CLK_EXTERN1>,
+				  <&tegra_pmc TEGRA_PMC_CLK_OUT_1>;
+
+		assigned-clock-parents = <&tegra_car TEGRA30_CLK_PLL_A_OUT0>,
+					 <&tegra_car TEGRA30_CLK_EXTERN1>;
+	};
+
+	thermal-zones {
+		/*
+		 * NCT72 has two sensors:
+		 *
+		 *	0: internal that monitors ambient/skin temperature
+		 *	1: external that is connected to the CPU's diode
+		 *
+		 * Ideally we should use userspace thermal governor,
+		 * but it's a much more complex solution.  The "skin"
+		 * zone exists as a simpler solution which prevents
+		 * Chagall from getting too hot from a user's tactile
+		 * perspective. The CPU zone is intended to protect
+		 * silicon from damage.
+		 */
+
+		skin-thermal {
+			polling-delay-passive = <1000>; /* milliseconds */
+			polling-delay = <5000>; /* milliseconds */
+
+			thermal-sensors = <&nct72 0>;
+
+			trips {
+				trip0: skin-alert {
+					/* throttle at 57C until temperature drops to 56.8C */
+					temperature = <57000>;
+					hysteresis = <200>;
+					type = "passive";
+				};
+
+				trip1: skin-crit {
+					/* shut down at 65C */
+					temperature = <65000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				map0 {
+					trip = <&trip0>;
+					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&actmon THERMAL_NO_LIMIT
+								  THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+
+		cpu-thermal {
+			polling-delay-passive = <1000>; /* milliseconds */
+			polling-delay = <5000>; /* milliseconds */
+
+			thermal-sensors = <&nct72 1>;
+
+			trips {
+				trip2: cpu-alert {
+					/* throttle at 85C until temperature drops to 84.8C */
+					temperature = <85000>;
+					hysteresis = <200>;
+					type = "passive";
+				};
+
+				trip3: cpu-crit {
+					/* shut down at 90C */
+					temperature = <90000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				map1 {
+					trip = <&trip2>;
+					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&actmon THERMAL_NO_LIMIT
+								  THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+	};
+};
+
+&emc_icc_dvfs_opp_table {
+	/delete-node/ opp-625000000-1200;
+	/delete-node/ opp-625000000-1250;
+	/delete-node/ opp-667000000-1200;
+	/delete-node/ opp-750000000-1300;
+	/delete-node/ opp-800000000-1300;
+	/delete-node/ opp-900000000-1350;
+};
+
+&emc_bw_dfs_opp_table {
+	/delete-node/ opp-625000000;
+	/delete-node/ opp-667000000;
+	/delete-node/ opp-750000000;
+	/delete-node/ opp-800000000;
+	/delete-node/ opp-900000000;
+};
diff --git a/arch/arm/boot/dts/tegra30-peripherals-opp.dtsi b/arch/arm/boot/dts/tegra30-peripherals-opp.dtsi
index 2c9780319725..d100a1a8b705 100644
--- a/arch/arm/boot/dts/tegra30-peripherals-opp.dtsi
+++ b/arch/arm/boot/dts/tegra30-peripherals-opp.dtsi
@@ -1,386 +1,1628 @@
 // SPDX-License-Identifier: GPL-2.0
 
 / {
-	emc_icc_dvfs_opp_table: emc-dvfs-opp-table {
+	core_opp_table: opp-table-core {
 		compatible = "operating-points-v2";
+		opp-shared;
 
-		opp@12750000,950 {
+		core_opp_950: opp-950000 {
+			opp-microvolt = <950000 950000 1350000>;
+			opp-level = <950000>;
+		};
+
+		core_opp_1000: opp-1000000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-level = <1000000>;
+		};
+
+		core_opp_1050: opp-1050000 {
+			opp-microvolt = <1050000 1050000 1350000>;
+			opp-level = <1050000>;
+		};
+
+		core_opp_1100: opp-1100000 {
+			opp-microvolt = <1100000 1100000 1350000>;
+			opp-level = <1100000>;
+		};
+
+		core_opp_1150: opp-1150000 {
+			opp-microvolt = <1150000 1150000 1350000>;
+			opp-level = <1150000>;
+		};
+
+		core_opp_1200: opp-1200000 {
+			opp-microvolt = <1200000 1200000 1350000>;
+			opp-level = <1200000>;
+		};
+
+		core_opp_1250: opp-1250000 {
+			opp-microvolt = <1250000 1250000 1350000>;
+			opp-level = <1250000>;
+		};
+
+		core_opp_1300: opp-1300000 {
+			opp-microvolt = <1300000 1300000 1350000>;
+			opp-level = <1300000>;
+		};
+
+		core_opp_1350: opp-1350000 {
+			opp-microvolt = <1350000 1350000 1350000>;
+			opp-level = <1350000>;
+		};
+	};
+
+	emc_icc_dvfs_opp_table: opp-table-emc {
+		compatible = "operating-points-v2";
+
+		opp-12750000-950 {
 			opp-microvolt = <950000 950000 1350000>;
 			opp-hz = /bits/ 64 <12750000>;
 			opp-supported-hw = <0x0006>;
+			required-opps = <&core_opp_950>;
 		};
 
-		opp@12750000,1000 {
+		opp-12750000-1000 {
 			opp-microvolt = <1000000 1000000 1350000>;
 			opp-hz = /bits/ 64 <12750000>;
 			opp-supported-hw = <0x0001>;
+			required-opps = <&core_opp_1000>;
 		};
 
-		opp@12750000,1250 {
+		opp-12750000-1250 {
 			opp-microvolt = <1250000 1250000 1350000>;
 			opp-hz = /bits/ 64 <12750000>;
 			opp-supported-hw = <0x0008>;
+			required-opps = <&core_opp_1250>;
 		};
 
-		opp@25500000,950 {
+		opp-25500000-950 {
 			opp-microvolt = <950000 950000 1350000>;
 			opp-hz = /bits/ 64 <25500000>;
 			opp-supported-hw = <0x0006>;
+			required-opps = <&core_opp_950>;
 		};
 
-		opp@25500000,1000 {
+		opp-25500000-1000 {
 			opp-microvolt = <1000000 1000000 1350000>;
 			opp-hz = /bits/ 64 <25500000>;
 			opp-supported-hw = <0x0001>;
+			required-opps = <&core_opp_1000>;
 		};
 
-		opp@25500000,1250 {
+		opp-25500000-1250 {
 			opp-microvolt = <1250000 1250000 1350000>;
 			opp-hz = /bits/ 64 <25500000>;
 			opp-supported-hw = <0x0008>;
+			required-opps = <&core_opp_1250>;
 		};
 
-		opp@27000000,950 {
+		opp-27000000-950 {
 			opp-microvolt = <950000 950000 1350000>;
 			opp-hz = /bits/ 64 <27000000>;
 			opp-supported-hw = <0x0006>;
+			required-opps = <&core_opp_950>;
 		};
 
-		opp@27000000,1000 {
+		opp-27000000-1000 {
 			opp-microvolt = <1000000 1000000 1350000>;
 			opp-hz = /bits/ 64 <27000000>;
 			opp-supported-hw = <0x0001>;
+			required-opps = <&core_opp_1000>;
 		};
 
-		opp@27000000,1250 {
+		opp-27000000-1250 {
 			opp-microvolt = <1250000 1250000 1350000>;
 			opp-hz = /bits/ 64 <27000000>;
 			opp-supported-hw = <0x0008>;
+			required-opps = <&core_opp_1250>;
 		};
 
-		opp@51000000,950 {
+		opp-51000000-950 {
 			opp-microvolt = <950000 950000 1350000>;
 			opp-hz = /bits/ 64 <51000000>;
 			opp-supported-hw = <0x0006>;
+			required-opps = <&core_opp_950>;
 		};
 
-		opp@51000000,1000 {
+		opp-51000000-1000 {
 			opp-microvolt = <1000000 1000000 1350000>;
 			opp-hz = /bits/ 64 <51000000>;
 			opp-supported-hw = <0x0001>;
+			required-opps = <&core_opp_1000>;
 		};
 
-		opp@51000000,1250 {
+		opp-51000000-1250 {
 			opp-microvolt = <1250000 1250000 1350000>;
 			opp-hz = /bits/ 64 <51000000>;
 			opp-supported-hw = <0x0008>;
+			required-opps = <&core_opp_1250>;
 		};
 
-		opp@54000000,950 {
+		opp-54000000-950 {
 			opp-microvolt = <950000 950000 1350000>;
 			opp-hz = /bits/ 64 <54000000>;
 			opp-supported-hw = <0x0006>;
+			required-opps = <&core_opp_950>;
 		};
 
-		opp@54000000,1000 {
+		opp-54000000-1000 {
 			opp-microvolt = <1000000 1000000 1350000>;
 			opp-hz = /bits/ 64 <54000000>;
 			opp-supported-hw = <0x0001>;
+			required-opps = <&core_opp_1000>;
 		};
 
-		opp@54000000,1250 {
+		opp-54000000-1250 {
 			opp-microvolt = <1250000 1250000 1350000>;
 			opp-hz = /bits/ 64 <54000000>;
 			opp-supported-hw = <0x0008>;
+			required-opps = <&core_opp_1250>;
 		};
 
-		opp@102000000,950 {
+		opp-102000000-950 {
 			opp-microvolt = <950000 950000 1350000>;
 			opp-hz = /bits/ 64 <102000000>;
 			opp-supported-hw = <0x0006>;
+			required-opps = <&core_opp_950>;
 		};
 
-		opp@102000000,1000 {
+		opp-102000000-1000 {
 			opp-microvolt = <1000000 1000000 1350000>;
 			opp-hz = /bits/ 64 <102000000>;
 			opp-supported-hw = <0x0001>;
+			required-opps = <&core_opp_1000>;
 		};
 
-		opp@102000000,1250 {
+		opp-102000000-1250 {
 			opp-microvolt = <1250000 1250000 1350000>;
 			opp-hz = /bits/ 64 <102000000>;
 			opp-supported-hw = <0x0008>;
+			required-opps = <&core_opp_1250>;
 		};
 
-		opp@108000000,1000 {
+		opp-108000000-1000 {
 			opp-microvolt = <1000000 1000000 1350000>;
 			opp-hz = /bits/ 64 <108000000>;
 			opp-supported-hw = <0x0007>;
+			required-opps = <&core_opp_1000>;
 		};
 
-		opp@108000000,1250 {
+		opp-108000000-1250 {
 			opp-microvolt = <1250000 1250000 1350000>;
 			opp-hz = /bits/ 64 <108000000>;
 			opp-supported-hw = <0x0008>;
+			required-opps = <&core_opp_1250>;
 		};
 
-		opp@204000000,1000 {
+		opp-204000000-1000 {
 			opp-microvolt = <1000000 1000000 1350000>;
 			opp-hz = /bits/ 64 <204000000>;
 			opp-supported-hw = <0x0007>;
+			required-opps = <&core_opp_1000>;
 			opp-suspend;
 		};
 
-		opp@204000000,1250 {
+		opp-204000000-1250 {
 			opp-microvolt = <1250000 1250000 1350000>;
 			opp-hz = /bits/ 64 <204000000>;
 			opp-supported-hw = <0x0008>;
+			required-opps = <&core_opp_1250>;
 			opp-suspend;
 		};
 
-		opp@333500000,1000 {
+		opp-333500000-1000 {
 			opp-microvolt = <1000000 1000000 1350000>;
 			opp-hz = /bits/ 64 <333500000>;
 			opp-supported-hw = <0x0006>;
+			required-opps = <&core_opp_1000>;
 		};
 
-		opp@333500000,1200 {
+		opp-333500000-1200 {
 			opp-microvolt = <1200000 1200000 1350000>;
 			opp-hz = /bits/ 64 <333500000>;
 			opp-supported-hw = <0x0001>;
+			required-opps = <&core_opp_1200>;
 		};
 
-		opp@333500000,1250 {
+		opp-333500000-1250 {
 			opp-microvolt = <1250000 1250000 1350000>;
 			opp-hz = /bits/ 64 <333500000>;
 			opp-supported-hw = <0x0008>;
+			required-opps = <&core_opp_1250>;
 		};
 
-		opp@375000000,1000 {
+		opp-375000000-1000 {
 			opp-microvolt = <1000000 1000000 1350000>;
 			opp-hz = /bits/ 64 <375000000>;
 			opp-supported-hw = <0x0006>;
+			required-opps = <&core_opp_1000>;
 		};
 
-		opp@375000000,1200 {
+		opp-375000000-1200 {
 			opp-microvolt = <1200000 1200000 1350000>;
 			opp-hz = /bits/ 64 <375000000>;
 			opp-supported-hw = <0x0001>;
+			required-opps = <&core_opp_1200>;
 		};
 
-		opp@375000000,1250 {
+		opp-375000000-1250 {
 			opp-microvolt = <1250000 1250000 1350000>;
 			opp-hz = /bits/ 64 <375000000>;
 			opp-supported-hw = <0x0008>;
+			required-opps = <&core_opp_1250>;
 		};
 
-		opp@400000000,1000 {
+		opp-400000000-1000 {
 			opp-microvolt = <1000000 1000000 1350000>;
 			opp-hz = /bits/ 64 <400000000>;
 			opp-supported-hw = <0x0006>;
+			required-opps = <&core_opp_1000>;
 		};
 
-		opp@400000000,1200 {
+		opp-400000000-1200 {
 			opp-microvolt = <1200000 1200000 1350000>;
 			opp-hz = /bits/ 64 <400000000>;
 			opp-supported-hw = <0x0001>;
+			required-opps = <&core_opp_1200>;
 		};
 
-		opp@400000000,1250 {
+		opp-400000000-1250 {
 			opp-microvolt = <1250000 1250000 1350000>;
 			opp-hz = /bits/ 64 <400000000>;
 			opp-supported-hw = <0x0008>;
+			required-opps = <&core_opp_1250>;
 		};
 
-		opp@416000000,1200 {
+		opp-416000000-1200 {
 			opp-microvolt = <1200000 1200000 1350000>;
 			opp-hz = /bits/ 64 <416000000>;
 			opp-supported-hw = <0x0007>;
+			required-opps = <&core_opp_1200>;
 		};
 
-		opp@416000000,1250 {
+		opp-416000000-1250 {
 			opp-microvolt = <1250000 1250000 1350000>;
 			opp-hz = /bits/ 64 <416000000>;
 			opp-supported-hw = <0x0008>;
+			required-opps = <&core_opp_1250>;
 		};
 
-		opp@450000000,1200 {
+		opp-450000000-1200 {
 			opp-microvolt = <1200000 1200000 1350000>;
 			opp-hz = /bits/ 64 <450000000>;
 			opp-supported-hw = <0x0007>;
+			required-opps = <&core_opp_1200>;
 		};
 
-		opp@450000000,1250 {
+		opp-450000000-1250 {
 			opp-microvolt = <1250000 1250000 1350000>;
 			opp-hz = /bits/ 64 <450000000>;
 			opp-supported-hw = <0x0008>;
+			required-opps = <&core_opp_1250>;
+		};
+
+		opp-500000000-1200 {
+			opp-microvolt = <1200000 1200000 1350000>;
+			opp-hz = /bits/ 64 <500000000>;
+			opp-supported-hw = <0x0007>;
+			required-opps = <&core_opp_1200>;
+		};
+
+		opp-500000000-1250 {
+			opp-microvolt = <1250000 1250000 1350000>;
+			opp-hz = /bits/ 64 <500000000>;
+			opp-supported-hw = <0x0008>;
+			required-opps = <&core_opp_1250>;
 		};
 
-		opp@533000000,1200 {
+		opp-533000000-1200 {
 			opp-microvolt = <1200000 1200000 1350000>;
 			opp-hz = /bits/ 64 <533000000>;
 			opp-supported-hw = <0x0007>;
+			required-opps = <&core_opp_1200>;
 		};
 
-		opp@533000000,1250 {
+		opp-533000000-1250 {
 			opp-microvolt = <1250000 1250000 1350000>;
 			opp-hz = /bits/ 64 <533000000>;
 			opp-supported-hw = <0x0008>;
+			required-opps = <&core_opp_1250>;
 		};
 
-		opp@625000000,1200 {
+		opp-625000000-1200 {
 			opp-microvolt = <1200000 1200000 1350000>;
 			opp-hz = /bits/ 64 <625000000>;
 			opp-supported-hw = <0x0006>;
+			required-opps = <&core_opp_1200>;
 		};
 
-		opp@625000000,1250 {
+		opp-625000000-1250 {
 			opp-microvolt = <1250000 1250000 1350000>;
 			opp-hz = /bits/ 64 <625000000>;
 			opp-supported-hw = <0x0008>;
+			required-opps = <&core_opp_1250>;
 		};
 
-		opp@667000000,1200 {
+		opp-667000000-1200 {
 			opp-microvolt = <1200000 1200000 1350000>;
 			opp-hz = /bits/ 64 <667000000>;
 			opp-supported-hw = <0x0006>;
+			required-opps = <&core_opp_1200>;
 		};
 
-		opp@750000000,1300 {
+		opp-750000000-1300 {
 			opp-microvolt = <1300000 1300000 1350000>;
 			opp-hz = /bits/ 64 <750000000>;
 			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1300>;
 		};
 
-		opp@800000000,1300 {
+		opp-800000000-1300 {
 			opp-microvolt = <1300000 1300000 1350000>;
 			opp-hz = /bits/ 64 <800000000>;
 			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1300>;
 		};
 
-		opp@900000000,1350 {
+		opp-900000000-1350 {
 			opp-microvolt = <1350000 1350000 1350000>;
 			opp-hz = /bits/ 64 <900000000>;
 			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1350>;
 		};
 	};
 
-	emc_bw_dfs_opp_table: emc-bandwidth-opp-table {
+	emc_bw_dfs_opp_table: opp-table-actmon {
 		compatible = "operating-points-v2";
 
-		opp@12750000 {
+		opp-12750000 {
 			opp-hz = /bits/ 64 <12750000>;
 			opp-supported-hw = <0x000F>;
 			opp-peak-kBps = <102000>;
 		};
 
-		opp@25500000 {
+		opp-25500000 {
 			opp-hz = /bits/ 64 <25500000>;
 			opp-supported-hw = <0x000F>;
 			opp-peak-kBps = <204000>;
 		};
 
-		opp@27000000 {
+		opp-27000000 {
 			opp-hz = /bits/ 64 <27000000>;
 			opp-supported-hw = <0x000F>;
 			opp-peak-kBps = <216000>;
 		};
 
-		opp@51000000 {
+		opp-51000000 {
 			opp-hz = /bits/ 64 <51000000>;
 			opp-supported-hw = <0x000F>;
 			opp-peak-kBps = <408000>;
 		};
 
-		opp@54000000 {
+		opp-54000000 {
 			opp-hz = /bits/ 64 <54000000>;
 			opp-supported-hw = <0x000F>;
 			opp-peak-kBps = <432000>;
 		};
 
-		opp@102000000 {
+		opp-102000000 {
 			opp-hz = /bits/ 64 <102000000>;
 			opp-supported-hw = <0x000F>;
 			opp-peak-kBps = <816000>;
 		};
 
-		opp@108000000 {
+		opp-108000000 {
 			opp-hz = /bits/ 64 <108000000>;
 			opp-supported-hw = <0x000F>;
 			opp-peak-kBps = <864000>;
 		};
 
-		opp@204000000 {
+		opp-204000000 {
 			opp-hz = /bits/ 64 <204000000>;
 			opp-supported-hw = <0x000F>;
 			opp-peak-kBps = <1632000>;
 			opp-suspend;
 		};
 
-		opp@333500000 {
+		opp-333500000 {
 			opp-hz = /bits/ 64 <333500000>;
 			opp-supported-hw = <0x000F>;
 			opp-peak-kBps = <2668000>;
 		};
 
-		opp@375000000 {
+		opp-375000000 {
 			opp-hz = /bits/ 64 <375000000>;
 			opp-supported-hw = <0x000F>;
 			opp-peak-kBps = <3000000>;
 		};
 
-		opp@400000000 {
+		opp-400000000 {
 			opp-hz = /bits/ 64 <400000000>;
 			opp-supported-hw = <0x000F>;
 			opp-peak-kBps = <3200000>;
 		};
 
-		opp@416000000 {
+		opp-416000000 {
 			opp-hz = /bits/ 64 <416000000>;
 			opp-supported-hw = <0x000F>;
 			opp-peak-kBps = <3328000>;
 		};
 
-		opp@450000000 {
+		opp-450000000 {
 			opp-hz = /bits/ 64 <450000000>;
 			opp-supported-hw = <0x000F>;
 			opp-peak-kBps = <3600000>;
 		};
 
-		opp@533000000 {
+		opp-500000000 {
+			opp-hz = /bits/ 64 <500000000>;
+			opp-supported-hw = <0x000F>;
+			opp-peak-kBps = <4000000>;
+		};
+
+		opp-533000000 {
 			opp-hz = /bits/ 64 <533000000>;
 			opp-supported-hw = <0x000F>;
 			opp-peak-kBps = <4264000>;
 		};
 
-		opp@625000000 {
+		opp-625000000 {
 			opp-hz = /bits/ 64 <625000000>;
 			opp-supported-hw = <0x000E>;
 			opp-peak-kBps = <5000000>;
 		};
 
-		opp@667000000 {
+		opp-667000000 {
 			opp-hz = /bits/ 64 <667000000>;
 			opp-supported-hw = <0x0006>;
 			opp-peak-kBps = <5336000>;
 		};
 
-		opp@750000000 {
+		opp-750000000 {
 			opp-hz = /bits/ 64 <750000000>;
 			opp-supported-hw = <0x0004>;
 			opp-peak-kBps = <6000000>;
 		};
 
-		opp@800000000 {
+		opp-800000000 {
 			opp-hz = /bits/ 64 <800000000>;
 			opp-supported-hw = <0x0004>;
 			opp-peak-kBps = <6400000>;
 		};
 
-		opp@900000000 {
+		opp-900000000 {
 			opp-hz = /bits/ 64 <900000000>;
 			opp-supported-hw = <0x0004>;
 			opp-peak-kBps = <7200000>;
 		};
 	};
+
+	pcie_dvfs_opp_table: opp-table-pcie {
+		compatible = "operating-points-v2";
+
+		opp-250000000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <250000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1000>;
+		};
+	};
+
+	host1x_dvfs_opp_table: opp-table-host1x {
+		compatible = "operating-points-v2";
+
+		opp-152000000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <152000000>;
+			opp-supported-hw = <0x0007>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-188000000-1050 {
+			opp-microvolt = <1050000 1050000 1350000>;
+			opp-hz = /bits/ 64 <188000000>;
+			opp-supported-hw = <0x0007>;
+			required-opps = <&core_opp_1050>;
+		};
+
+		opp-222000000-1100 {
+			opp-microvolt = <1100000 1100000 1350000>;
+			opp-hz = /bits/ 64 <222000000>;
+			opp-supported-hw = <0x0007>;
+			required-opps = <&core_opp_1100>;
+		};
+
+		opp-242000000-1250 {
+			opp-microvolt = <1250000 1250000 1350000>;
+			opp-hz = /bits/ 64 <242000000>;
+			opp-supported-hw = <0x0008>;
+			required-opps = <&core_opp_1250>;
+		};
+
+		opp-254000000-1150 {
+			opp-microvolt = <1150000 1150000 1350000>;
+			opp-hz = /bits/ 64 <254000000>;
+			opp-supported-hw = <0x0007>;
+			required-opps = <&core_opp_1150>;
+		};
+
+		opp-267000000-1200 {
+			opp-microvolt = <1200000 1200000 1350000>;
+			opp-hz = /bits/ 64 <267000000>;
+			opp-supported-hw = <0x0007>;
+			required-opps = <&core_opp_1200>;
+		};
+
+		opp-300000000-1350 {
+			opp-microvolt = <1350000 1350000 1350000>;
+			opp-hz = /bits/ 64 <300000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1350>;
+		};
+	};
+
+	mpe_dvfs_opp_table: opp-table-mpe {
+		compatible = "operating-points-v2";
+
+		opp-234000000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <234000000>;
+			opp-supported-hw = <0x0003>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-247000000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <247000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-285000000-1050 {
+			opp-microvolt = <1050000 1050000 1350000>;
+			opp-hz = /bits/ 64 <285000000>;
+			opp-supported-hw = <0x0003>;
+			required-opps = <&core_opp_1050>;
+		};
+
+		opp-304000000-1050 {
+			opp-microvolt = <1050000 1050000 1350000>;
+			opp-hz = /bits/ 64 <304000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1050>;
+		};
+
+		opp-332000000-1100 {
+			opp-microvolt = <1100000 1100000 1350000>;
+			opp-hz = /bits/ 64 <332000000>;
+			opp-supported-hw = <0x0003>;
+			required-opps = <&core_opp_1100>;
+		};
+
+		opp-361000000-1100 {
+			opp-microvolt = <1100000 1100000 1350000>;
+			opp-hz = /bits/ 64 <361000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1100>;
+		};
+
+		opp-380000000-1150 {
+			opp-microvolt = <1150000 1150000 1350000>;
+			opp-hz = /bits/ 64 <380000000>;
+			opp-supported-hw = <0x0003>;
+			required-opps = <&core_opp_1150>;
+		};
+
+		opp-408000000-1150 {
+			opp-microvolt = <1150000 1150000 1350000>;
+			opp-hz = /bits/ 64 <408000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1150>;
+		};
+
+		opp-416000000-1200 {
+			opp-microvolt = <1200000 1200000 1350000>;
+			opp-hz = /bits/ 64 <416000000>;
+			opp-supported-hw = <0x0003>;
+			required-opps = <&core_opp_1200>;
+		};
+
+		opp-446000000-1200 {
+			opp-microvolt = <1200000 1200000 1350000>;
+			opp-hz = /bits/ 64 <446000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1200>;
+		};
+
+		opp-484000000-1250 {
+			opp-microvolt = <1250000 1250000 1350000>;
+			opp-hz = /bits/ 64 <484000000>;
+			opp-supported-hw = <0x000C>;
+			required-opps = <&core_opp_1250>;
+		};
+
+		opp-520000000-1300 {
+			opp-microvolt = <1300000 1300000 1350000>;
+			opp-hz = /bits/ 64 <520000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1300>;
+		};
+
+		opp-600000000-1350 {
+			opp-microvolt = <1350000 1350000 1350000>;
+			opp-hz = /bits/ 64 <600000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1350>;
+		};
+	};
+
+	vi_dvfs_opp_table: opp-table-vi {
+		compatible = "operating-points-v2";
+
+		opp-216000000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <216000000>;
+			opp-supported-hw = <0x0003>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-219000000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <219000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-267000000-1050 {
+			opp-microvolt = <1050000 1050000 1350000>;
+			opp-hz = /bits/ 64 <267000000>;
+			opp-supported-hw = <0x0006>;
+			required-opps = <&core_opp_1050>;
+		};
+
+		opp-285000000-1050 {
+			opp-microvolt = <1050000 1050000 1350000>;
+			opp-hz = /bits/ 64 <285000000>;
+			opp-supported-hw = <0x0001>;
+			required-opps = <&core_opp_1050>;
+		};
+
+		opp-300000000-1100 {
+			opp-microvolt = <1100000 1100000 1350000>;
+			opp-hz = /bits/ 64 <300000000>;
+			opp-supported-hw = <0x0007>;
+			required-opps = <&core_opp_1100>;
+		};
+
+		opp-371000000-1150 {
+			opp-microvolt = <1150000 1150000 1350000>;
+			opp-hz = /bits/ 64 <371000000>;
+			opp-supported-hw = <0x0006>;
+			required-opps = <&core_opp_1150>;
+		};
+
+		opp-409000000-1200 {
+			opp-microvolt = <1200000 1200000 1350000>;
+			opp-hz = /bits/ 64 <409000000>;
+			opp-supported-hw = <0x0006>;
+			required-opps = <&core_opp_1200>;
+		};
+
+		opp-425000000-1250 {
+			opp-microvolt = <1250000 1250000 1350000>;
+			opp-hz = /bits/ 64 <425000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1250>;
+		};
+
+		opp-470000000-1250 {
+			opp-microvolt = <1250000 1250000 1350000>;
+			opp-hz = /bits/ 64 <470000000>;
+			opp-supported-hw = <0x0008>;
+			required-opps = <&core_opp_1250>;
+		};
+	};
+
+	epp_dvfs_opp_table: opp-table-epp {
+		compatible = "operating-points-v2";
+
+		opp-267000000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <267000000>;
+			opp-supported-hw = <0x0007>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-285000000-1050 {
+			opp-microvolt = <1050000 1050000 1350000>;
+			opp-hz = /bits/ 64 <285000000>;
+			opp-supported-hw = <0x0003>;
+			required-opps = <&core_opp_1050>;
+		};
+
+		opp-304000000-1050 {
+			opp-microvolt = <1050000 1050000 1350000>;
+			opp-hz = /bits/ 64 <304000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1050>;
+		};
+
+		opp-332000000-1100 {
+			opp-microvolt = <1100000 1100000 1350000>;
+			opp-hz = /bits/ 64 <332000000>;
+			opp-supported-hw = <0x0003>;
+			required-opps = <&core_opp_1100>;
+		};
+
+		opp-361000000-1100 {
+			opp-microvolt = <1100000 1100000 1350000>;
+			opp-hz = /bits/ 64 <361000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1100>;
+		};
+
+		opp-380000000-1150 {
+			opp-microvolt = <1150000 1150000 1350000>;
+			opp-hz = /bits/ 64 <380000000>;
+			opp-supported-hw = <0x0003>;
+			required-opps = <&core_opp_1150>;
+		};
+
+		opp-408000000-1150 {
+			opp-microvolt = <1150000 1150000 1350000>;
+			opp-hz = /bits/ 64 <408000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1150>;
+		};
+
+		opp-416000000-1200 {
+			opp-microvolt = <1200000 1200000 1350000>;
+			opp-hz = /bits/ 64 <416000000>;
+			opp-supported-hw = <0x0003>;
+			required-opps = <&core_opp_1200>;
+		};
+
+		opp-446000000-1200 {
+			opp-microvolt = <1200000 1200000 1350000>;
+			opp-hz = /bits/ 64 <446000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1200>;
+		};
+
+		opp-484000000-1250 {
+			opp-microvolt = <1250000 1250000 1350000>;
+			opp-hz = /bits/ 64 <484000000>;
+			opp-supported-hw = <0x000C>;
+			required-opps = <&core_opp_1250>;
+		};
+
+		opp-520000000-1300 {
+			opp-microvolt = <1300000 1300000 1350000>;
+			opp-hz = /bits/ 64 <520000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1300>;
+		};
+
+		opp-600000000-1350 {
+			opp-microvolt = <1350000 1350000 1350000>;
+			opp-hz = /bits/ 64 <600000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1350>;
+		};
+	};
+
+	gr2d_dvfs_opp_table: opp-table-gr2d {
+		compatible = "operating-points-v2";
+
+		opp-267000000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <267000000>;
+			opp-supported-hw = <0x0007>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-285000000-1050 {
+			opp-microvolt = <1050000 1050000 1350000>;
+			opp-hz = /bits/ 64 <285000000>;
+			opp-supported-hw = <0x0003>;
+			required-opps = <&core_opp_1050>;
+		};
+
+		opp-304000000-1050 {
+			opp-microvolt = <1050000 1050000 1350000>;
+			opp-hz = /bits/ 64 <304000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1050>;
+		};
+
+		opp-332000000-1100 {
+			opp-microvolt = <1100000 1100000 1350000>;
+			opp-hz = /bits/ 64 <332000000>;
+			opp-supported-hw = <0x0003>;
+			required-opps = <&core_opp_1100>;
+		};
+
+		opp-361000000-1100 {
+			opp-microvolt = <1100000 1100000 1350000>;
+			opp-hz = /bits/ 64 <361000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1100>;
+		};
+
+		opp-380000000-1150 {
+			opp-microvolt = <1150000 1150000 1350000>;
+			opp-hz = /bits/ 64 <380000000>;
+			opp-supported-hw = <0x0003>;
+			required-opps = <&core_opp_1150>;
+		};
+
+		opp-408000000-1150 {
+			opp-microvolt = <1150000 1150000 1350000>;
+			opp-hz = /bits/ 64 <408000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1150>;
+		};
+
+		opp-416000000-1200 {
+			opp-microvolt = <1200000 1200000 1350000>;
+			opp-hz = /bits/ 64 <416000000>;
+			opp-supported-hw = <0x0003>;
+			required-opps = <&core_opp_1200>;
+		};
+
+		opp-446000000-1200 {
+			opp-microvolt = <1200000 1200000 1350000>;
+			opp-hz = /bits/ 64 <446000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1200>;
+		};
+
+		opp-484000000-1250 {
+			opp-microvolt = <1250000 1250000 1350000>;
+			opp-hz = /bits/ 64 <484000000>;
+			opp-supported-hw = <0x000C>;
+			required-opps = <&core_opp_1250>;
+		};
+
+		opp-520000000-1300 {
+			opp-microvolt = <1300000 1300000 1350000>;
+			opp-hz = /bits/ 64 <520000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1300>;
+		};
+
+		opp-600000000-1350 {
+			opp-microvolt = <1350000 1350000 1350000>;
+			opp-hz = /bits/ 64 <600000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1350>;
+		};
+	};
+
+	gr3d_dvfs_opp_table: opp-table-gr3d {
+		compatible = "operating-points-v2";
+
+		opp-234000000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <234000000>;
+			opp-supported-hw = <0x0003>;
+			required-opps = <&core_opp_1000>, <&core_opp_1000>;
+		};
+
+		opp-247000000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <247000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1000>, <&core_opp_1000>;
+		};
+
+		opp-285000000-1050 {
+			opp-microvolt = <1050000 1050000 1350000>;
+			opp-hz = /bits/ 64 <285000000>;
+			opp-supported-hw = <0x0003>;
+			required-opps = <&core_opp_1050>, <&core_opp_1050>;
+		};
+
+		opp-304000000-1050 {
+			opp-microvolt = <1050000 1050000 1350000>;
+			opp-hz = /bits/ 64 <304000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1050>, <&core_opp_1050>;
+		};
+
+		opp-332000000-1100 {
+			opp-microvolt = <1100000 1100000 1350000>;
+			opp-hz = /bits/ 64 <332000000>;
+			opp-supported-hw = <0x0003>;
+			required-opps = <&core_opp_1100>, <&core_opp_1100>;
+		};
+
+		opp-361000000-1100 {
+			opp-microvolt = <1100000 1100000 1350000>;
+			opp-hz = /bits/ 64 <361000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1100>, <&core_opp_1100>;
+		};
+
+		opp-380000000-1150 {
+			opp-microvolt = <1150000 1150000 1350000>;
+			opp-hz = /bits/ 64 <380000000>;
+			opp-supported-hw = <0x0003>;
+			required-opps = <&core_opp_1150>, <&core_opp_1150>;
+		};
+
+		opp-408000000-1150 {
+			opp-microvolt = <1150000 1150000 1350000>;
+			opp-hz = /bits/ 64 <408000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1150>, <&core_opp_1150>;
+		};
+
+		opp-416000000-1200 {
+			opp-microvolt = <1200000 1200000 1350000>;
+			opp-hz = /bits/ 64 <416000000>;
+			opp-supported-hw = <0x0003>;
+			required-opps = <&core_opp_1200>, <&core_opp_1200>;
+		};
+
+		opp-446000000-1200 {
+			opp-microvolt = <1200000 1200000 1350000>;
+			opp-hz = /bits/ 64 <446000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1200>, <&core_opp_1200>;
+		};
+
+		opp-484000000-1250 {
+			opp-microvolt = <1250000 1250000 1350000>;
+			opp-hz = /bits/ 64 <484000000>;
+			opp-supported-hw = <0x000C>;
+			required-opps = <&core_opp_1250>, <&core_opp_1250>;
+		};
+
+		opp-520000000-1300 {
+			opp-microvolt = <1300000 1300000 1350000>;
+			opp-hz = /bits/ 64 <520000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1300>, <&core_opp_1300>;
+		};
+
+		opp-600000000-1350 {
+			opp-microvolt = <1350000 1350000 1350000>;
+			opp-hz = /bits/ 64 <600000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1350>, <&core_opp_1350>;
+		};
+	};
+
+	disp1_dvfs_opp_table: opp-table-disp1 {
+		compatible = "operating-points-v2";
+
+		opp-120000000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <120000000>;
+			opp-supported-hw = <0x0009>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-155000000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <155000000>;
+			opp-supported-hw = <0x0006>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-190000000-1200 {
+			opp-microvolt = <1200000 1200000 1350000>;
+			opp-hz = /bits/ 64 <190000000>;
+			opp-supported-hw = <0x0009>;
+			required-opps = <&core_opp_1200>;
+		};
+
+		opp-268000000-1050 {
+			opp-microvolt = <1050000 1050000 1350000>;
+			opp-hz = /bits/ 64 <268000000>;
+			opp-supported-hw = <0x0006>;
+			required-opps = <&core_opp_1050>;
+		};
+	};
+
+	disp2_dvfs_opp_table: opp-table-disp2 {
+		compatible = "operating-points-v2";
+
+		opp-120000000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <120000000>;
+			opp-supported-hw = <0x0009>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-155000000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <155000000>;
+			opp-supported-hw = <0x0006>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-190000000-1200 {
+			opp-microvolt = <1200000 1200000 1350000>;
+			opp-hz = /bits/ 64 <190000000>;
+			opp-supported-hw = <0x0009>;
+			required-opps = <&core_opp_1200>;
+		};
+
+		opp-268000000-1050 {
+			opp-microvolt = <1050000 1050000 1350000>;
+			opp-hz = /bits/ 64 <268000000>;
+			opp-supported-hw = <0x0006>;
+			required-opps = <&core_opp_1050>;
+		};
+	};
+
+	hdmi_dvfs_opp_table: opp-table-hdmi {
+		compatible = "operating-points-v2";
+
+		opp-148500000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <148500000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1000>;
+		};
+	};
+
+	tvo_dvfs_opp_table: opp-table-tvo {
+		compatible = "operating-points-v2";
+
+		opp-297000000-1050 {
+			opp-microvolt = <1050000 1050000 1350000>;
+			opp-hz = /bits/ 64 <297000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1050>;
+		};
+	};
+
+	dsia_dvfs_opp_table: opp-table-dsia {
+		compatible = "operating-points-v2";
+
+		opp-275000000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <275000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1000>;
+		};
+	};
+
+	dsib_dvfs_opp_table: opp-table-dsib {
+		compatible = "operating-points-v2";
+
+		opp-275000000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <275000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1000>;
+		};
+	};
+
+	sclk_dvfs_opp_table: opp-table-sclk {
+		compatible = "operating-points-v2";
+
+		opp-51000000-950 {
+			opp-microvolt = <950000 950000 1350000>;
+			opp-hz = /bits/ 64 <51000000>;
+			opp-supported-hw = <0x0006>;
+			required-opps = <&core_opp_950>;
+		};
+
+		opp-136000000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <136000000>;
+			opp-supported-hw = <0x0001>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-164000000-1050 {
+			opp-microvolt = <1050000 1050000 1350000>;
+			opp-hz = /bits/ 64 <164000000>;
+			opp-supported-hw = <0x0001>;
+			required-opps = <&core_opp_1050>;
+		};
+
+		opp-191000000-1100 {
+			opp-microvolt = <1100000 1100000 1350000>;
+			opp-hz = /bits/ 64 <191000000>;
+			opp-supported-hw = <0x0001>;
+			required-opps = <&core_opp_1100>;
+		};
+
+		opp-205000000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <205000000>;
+			opp-supported-hw = <0x0006>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-216000000-1150 {
+			opp-microvolt = <1150000 1150000 1350000>;
+			opp-hz = /bits/ 64 <216000000>;
+			opp-supported-hw = <0x0001>;
+			required-opps = <&core_opp_1150>;
+		};
+
+		opp-227000000-1100 {
+			opp-microvolt = <1100000 1100000 1350000>;
+			opp-hz = /bits/ 64 <227000000>;
+			opp-supported-hw = <0x0006>;
+			required-opps = <&core_opp_1100>;
+		};
+
+		opp-267000000-1200 {
+			opp-microvolt = <1200000 1200000 1350000>;
+			opp-hz = /bits/ 64 <267000000>;
+			opp-supported-hw = <0x0006>;
+			required-opps = <&core_opp_1200>;
+		};
+
+		opp-334000000-1250 {
+			opp-microvolt = <1250000 1250000 1350000>;
+			opp-hz = /bits/ 64 <334000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1250>;
+		};
+
+		opp-378000000-1250 {
+			opp-microvolt = <1250000 1250000 1350000>;
+			opp-hz = /bits/ 64 <378000000>;
+			opp-supported-hw = <0x0008>;
+			required-opps = <&core_opp_1250>;
+		};
+	};
+
+	pll_c_dvfs_opp_table: opp-table-pllc {
+		compatible = "operating-points-v2";
+
+		opp-533000000-950 {
+			opp-microvolt = <950000 950000 1350000>;
+			opp-hz = /bits/ 64 <533000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_950>;
+		};
+
+		opp-667000000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <667000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-800000000-1100 {
+			opp-microvolt = <1100000 1100000 1350000>;
+			opp-hz = /bits/ 64 <800000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1100>;
+		};
+
+		opp-1066000000-1200 {
+			opp-microvolt = <1200000 1200000 1350000>;
+			opp-hz = /bits/ 64 <1066000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1200>;
+		};
+
+		opp-1200000000-1350 {
+			opp-microvolt = <1350000 1350000 1350000>;
+			opp-hz = /bits/ 64 <1200000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1350>;
+		};
+	};
+
+	pll_e_dvfs_opp_table: opp-table-plle {
+		compatible = "operating-points-v2";
+
+		opp-100000000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <100000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1000>;
+		};
+	};
+
+	pll_m_dvfs_opp_table: opp-table-pllm {
+		compatible = "operating-points-v2";
+
+		opp-533000000-950 {
+			opp-microvolt = <950000 950000 1350000>;
+			opp-hz = /bits/ 64 <533000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_950>;
+		};
+
+		opp-667000000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <667000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-800000000-1100 {
+			opp-microvolt = <1100000 1100000 1350000>;
+			opp-hz = /bits/ 64 <800000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1100>;
+		};
+
+		opp-1066000000-1200 {
+			opp-microvolt = <1200000 1200000 1350000>;
+			opp-hz = /bits/ 64 <1066000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1200>;
+		};
+	};
+
+	vde_dvfs_opp_table: opp-table-vde {
+		compatible = "operating-points-v2";
+
+		opp-228000000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <228000000>;
+			opp-supported-hw = <0x0003>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-247000000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <247000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-275000000-1050 {
+			opp-microvolt = <1050000 1050000 1350000>;
+			opp-hz = /bits/ 64 <275000000>;
+			opp-supported-hw = <0x0003>;
+			required-opps = <&core_opp_1050>;
+		};
+
+		opp-304000000-1050 {
+			opp-microvolt = <1050000 1050000 1350000>;
+			opp-hz = /bits/ 64 <304000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1050>;
+		};
+
+		opp-332000000-1100 {
+			opp-microvolt = <1100000 1100000 1350000>;
+			opp-hz = /bits/ 64 <332000000>;
+			opp-supported-hw = <0x0003>;
+			required-opps = <&core_opp_1100>;
+		};
+
+		opp-352000000-1100 {
+			opp-microvolt = <1100000 1100000 1350000>;
+			opp-hz = /bits/ 64 <352000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1100>;
+		};
+
+		opp-380000000-1150 {
+			opp-microvolt = <1150000 1150000 1350000>;
+			opp-hz = /bits/ 64 <380000000>;
+			opp-supported-hw = <0x0003>;
+			required-opps = <&core_opp_1150>;
+		};
+
+		opp-400000000-1150 {
+			opp-microvolt = <1150000 1150000 1350000>;
+			opp-hz = /bits/ 64 <400000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1150>;
+		};
+
+		opp-416000000-1200 {
+			opp-microvolt = <1200000 1200000 1350000>;
+			opp-hz = /bits/ 64 <416000000>;
+			opp-supported-hw = <0x0003>;
+			required-opps = <&core_opp_1200>;
+		};
+
+		opp-437000000-1200 {
+			opp-microvolt = <1200000 1200000 1350000>;
+			opp-hz = /bits/ 64 <437000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1200>;
+		};
+
+		opp-484000000-1250 {
+			opp-microvolt = <1250000 1250000 1350000>;
+			opp-hz = /bits/ 64 <484000000>;
+			opp-supported-hw = <0x000C>;
+			required-opps = <&core_opp_1250>;
+		};
+
+		opp-520000000-1300 {
+			opp-microvolt = <1300000 1300000 1350000>;
+			opp-hz = /bits/ 64 <520000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1300>;
+		};
+
+		opp-600000000-1350 {
+			opp-microvolt = <1350000 1350000 1350000>;
+			opp-hz = /bits/ 64 <600000000>;
+			opp-supported-hw = <0x0004>;
+			required-opps = <&core_opp_1350>;
+		};
+	};
+
+	fuse_burn_dvfs_opp_table: opp-table-fuseburn {
+		compatible = "operating-points-v2";
+
+		opp-26000000-1150 {
+			opp-microvolt = <1150000 1150000 1350000>;
+			opp-hz = /bits/ 64 <26000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1150>;
+		};
+	};
+
+	nor_dvfs_opp_table: opp-table-nor {
+		compatible = "operating-points-v2";
+
+		opp-108000000-1250 {
+			opp-microvolt = <1250000 1250000 1350000>;
+			opp-hz = /bits/ 64 <108000000>;
+			opp-supported-hw = <0x0008>;
+			required-opps = <&core_opp_1250>;
+		};
+
+		opp-115000000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <115000000>;
+			opp-supported-hw = <0x0007>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-130000000-1050 {
+			opp-microvolt = <1050000 1050000 1350000>;
+			opp-hz = /bits/ 64 <130000000>;
+			opp-supported-hw = <0x0007>;
+			required-opps = <&core_opp_1050>;
+		};
+
+		opp-133000000-1150 {
+			opp-microvolt = <1150000 1150000 1350000>;
+			opp-hz = /bits/ 64 <133000000>;
+			opp-supported-hw = <0x0007>;
+			required-opps = <&core_opp_1150>;
+		};
+	};
+
+	pwm_dvfs_opp_table: opp-table-pwm {
+		compatible = "operating-points-v2";
+
+		opp-408000000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <408000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1000>;
+		};
+	};
+
+	sbc1_dvfs_opp_table: opp-table-sbc1 {
+		compatible = "operating-points-v2";
+
+		opp-52000000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <52000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-60000000-1050 {
+			opp-microvolt = <1050000 1050000 1350000>;
+			opp-hz = /bits/ 64 <60000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1050>;
+		};
+
+		opp-100000000-1200 {
+			opp-microvolt = <1200000 1200000 1350000>;
+			opp-hz = /bits/ 64 <100000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1200>;
+		};
+	};
+
+	sbc2_dvfs_opp_table: opp-table-sbc2 {
+		compatible = "operating-points-v2";
+
+		opp-52000000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <52000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-60000000-1050 {
+			opp-microvolt = <1050000 1050000 1350000>;
+			opp-hz = /bits/ 64 <60000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1050>;
+		};
+
+		opp-100000000-1200 {
+			opp-microvolt = <1200000 1200000 1350000>;
+			opp-hz = /bits/ 64 <100000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1200>;
+		};
+	};
+
+	sbc3_dvfs_opp_table: opp-table-sbc3 {
+		compatible = "operating-points-v2";
+
+		opp-52000000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <52000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-60000000-1050 {
+			opp-microvolt = <1050000 1050000 1350000>;
+			opp-hz = /bits/ 64 <60000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1050>;
+		};
+
+		opp-100000000-1200 {
+			opp-microvolt = <1200000 1200000 1350000>;
+			opp-hz = /bits/ 64 <100000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1200>;
+		};
+	};
+
+	sbc4_dvfs_opp_table: opp-table-sbc4 {
+		compatible = "operating-points-v2";
+
+		opp-52000000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <52000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-60000000-1050 {
+			opp-microvolt = <1050000 1050000 1350000>;
+			opp-hz = /bits/ 64 <60000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1050>;
+		};
+
+		opp-100000000-1200 {
+			opp-microvolt = <1200000 1200000 1350000>;
+			opp-hz = /bits/ 64 <100000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1200>;
+		};
+	};
+
+	sbc5_dvfs_opp_table: opp-table-sbc5 {
+		compatible = "operating-points-v2";
+
+		opp-52000000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <52000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-60000000-1050 {
+			opp-microvolt = <1050000 1050000 1350000>;
+			opp-hz = /bits/ 64 <60000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1050>;
+		};
+
+		opp-100000000-1200 {
+			opp-microvolt = <1200000 1200000 1350000>;
+			opp-hz = /bits/ 64 <100000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1200>;
+		};
+	};
+
+	sbc6_dvfs_opp_table: opp-table-sbc6 {
+		compatible = "operating-points-v2";
+
+		opp-52000000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <52000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1000>;
+		};
+
+		opp-60000000-1050 {
+			opp-microvolt = <1050000 1050000 1350000>;
+			opp-hz = /bits/ 64 <60000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1050>;
+		};
+
+		opp-100000000-1200 {
+			opp-microvolt = <1200000 1200000 1350000>;
+			opp-hz = /bits/ 64 <100000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1200>;
+		};
+	};
+
+	sdmmc1_dvfs_opp_table: opp-table-sdmmc1 {
+		compatible = "operating-points-v2";
+
+		opp-104000000-950 {
+			opp-microvolt = <950000 950000 1350000>;
+			opp-hz = /bits/ 64 <104000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_950>;
+		};
+
+		opp-208000000-1200 {
+			opp-microvolt = <1200000 1200000 1350000>;
+			opp-hz = /bits/ 64 <208000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1200>;
+		};
+	};
+
+	sdmmc3_dvfs_opp_table: opp-table-sdmmc3 {
+		compatible = "operating-points-v2";
+
+		opp-104000000-950 {
+			opp-microvolt = <950000 950000 1350000>;
+			opp-hz = /bits/ 64 <104000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_950>;
+		};
+
+		opp-208000000-1200 {
+			opp-microvolt = <1200000 1200000 1350000>;
+			opp-hz = /bits/ 64 <208000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1200>;
+		};
+	};
+
+	usbd_dvfs_opp_table: opp-table-usbd {
+		compatible = "operating-points-v2";
+
+		opp-480000000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <480000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1000>;
+		};
+	};
+
+	usb2_dvfs_opp_table: opp-table-usb2 {
+		compatible = "operating-points-v2";
+
+		opp-480000000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <480000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1000>;
+		};
+	};
+
+	usb3_dvfs_opp_table: opp-table-usb3 {
+		compatible = "operating-points-v2";
+
+		opp-480000000-1000 {
+			opp-microvolt = <1000000 1000000 1350000>;
+			opp-hz = /bits/ 64 <480000000>;
+			opp-supported-hw = <0x000F>;
+			required-opps = <&core_opp_1000>;
+		};
+	};
 };
diff --git a/arch/arm/boot/dts/tegra30.dtsi b/arch/arm/boot/dts/tegra30.dtsi
index ae3df73c20a7..9dab8d2c158a 100644
--- a/arch/arm/boot/dts/tegra30.dtsi
+++ b/arch/arm/boot/dts/tegra30.dtsi
@@ -55,6 +55,8 @@
 			 <&tegra_car 72>,
 			 <&tegra_car 74>;
 		reset-names = "pex", "afi", "pcie_x";
+		power-domains = <&pd_core>;
+		operating-points-v2 = <&pcie_dvfs_opp_table>;
 		status = "disabled";
 
 		pci@1,0 {
@@ -121,9 +123,11 @@
 		interrupt-names = "syncpt", "host1x";
 		clocks = <&tegra_car TEGRA30_CLK_HOST1X>;
 		clock-names = "host1x";
-		resets = <&tegra_car 28>;
-		reset-names = "host1x";
+		resets = <&tegra_car 28>, <&mc TEGRA30_MC_RESET_HC>;
+		reset-names = "host1x", "mc";
 		iommus = <&mc TEGRA_SWGROUP_HC>;
+		power-domains = <&pd_heg>;
+		operating-points-v2 = <&host1x_dvfs_opp_table>;
 
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -137,8 +141,12 @@
 			clocks = <&tegra_car TEGRA30_CLK_MPE>;
 			resets = <&tegra_car 60>;
 			reset-names = "mpe";
+			power-domains = <&pd_mpe>;
+			operating-points-v2 = <&mpe_dvfs_opp_table>;
 
 			iommus = <&mc TEGRA_SWGROUP_MPE>;
+
+			status = "disabled";
 		};
 
 		vi@54080000 {
@@ -148,8 +156,12 @@
 			clocks = <&tegra_car TEGRA30_CLK_VI>;
 			resets = <&tegra_car 20>;
 			reset-names = "vi";
+			power-domains = <&pd_venc>;
+			operating-points-v2 = <&vi_dvfs_opp_table>;
 
 			iommus = <&mc TEGRA_SWGROUP_VI>;
+
+			status = "disabled";
 		};
 
 		epp@540c0000 {
@@ -159,8 +171,12 @@
 			clocks = <&tegra_car TEGRA30_CLK_EPP>;
 			resets = <&tegra_car 19>;
 			reset-names = "epp";
+			power-domains = <&pd_heg>;
+			operating-points-v2 = <&epp_dvfs_opp_table>;
 
 			iommus = <&mc TEGRA_SWGROUP_EPP>;
+
+			status = "disabled";
 		};
 
 		isp@54100000 {
@@ -170,8 +186,11 @@
 			clocks = <&tegra_car TEGRA30_CLK_ISP>;
 			resets = <&tegra_car 23>;
 			reset-names = "isp";
+			power-domains = <&pd_venc>;
 
 			iommus = <&mc TEGRA_SWGROUP_ISP>;
+
+			status = "disabled";
 		};
 
 		gr2d@54140000 {
@@ -179,8 +198,10 @@
 			reg = <0x54140000 0x00040000>;
 			interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&tegra_car TEGRA30_CLK_GR2D>;
-			resets = <&tegra_car 21>;
-			reset-names = "2d";
+			resets = <&tegra_car 21>, <&mc TEGRA30_MC_RESET_2D>;
+			reset-names = "2d", "mc";
+			power-domains = <&pd_heg>;
+			operating-points-v2 = <&gr2d_dvfs_opp_table>;
 
 			iommus = <&mc TEGRA_SWGROUP_G2>;
 		};
@@ -192,8 +213,13 @@
 				 <&tegra_car TEGRA30_CLK_GR3D2>;
 			clock-names = "3d", "3d2";
 			resets = <&tegra_car 24>,
-				 <&tegra_car 98>;
-			reset-names = "3d", "3d2";
+				 <&tegra_car 98>,
+				 <&mc TEGRA30_MC_RESET_3D>,
+				 <&mc TEGRA30_MC_RESET_3D2>;
+			reset-names = "3d", "3d2", "mc", "mc2";
+			power-domains = <&pd_3d0>, <&pd_3d1>;
+			power-domain-names = "3d0", "3d1";
+			operating-points-v2 = <&gr3d_dvfs_opp_table>;
 
 			iommus = <&mc TEGRA_SWGROUP_NV>,
 				 <&mc TEGRA_SWGROUP_NV2>;
@@ -208,6 +234,8 @@
 			clock-names = "dc", "parent";
 			resets = <&tegra_car 27>;
 			reset-names = "dc";
+			power-domains = <&pd_core>;
+			operating-points-v2 = <&disp1_dvfs_opp_table>;
 
 			iommus = <&mc TEGRA_SWGROUP_DC>;
 
@@ -238,6 +266,8 @@
 			clock-names = "dc", "parent";
 			resets = <&tegra_car 26>;
 			reset-names = "dc";
+			power-domains = <&pd_core>;
+			operating-points-v2 = <&disp2_dvfs_opp_table>;
 
 			iommus = <&mc TEGRA_SWGROUP_DCB>;
 
@@ -268,6 +298,8 @@
 			clock-names = "hdmi", "parent";
 			resets = <&tegra_car 51>;
 			reset-names = "hdmi";
+			power-domains = <&pd_core>;
+			operating-points-v2 = <&hdmi_dvfs_opp_table>;
 			status = "disabled";
 		};
 
@@ -276,6 +308,8 @@
 			reg = <0x542c0000 0x00040000>;
 			interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&tegra_car TEGRA30_CLK_TVO>;
+			power-domains = <&pd_core>;
+			operating-points-v2 = <&tvo_dvfs_opp_table>;
 			status = "disabled";
 		};
 
@@ -287,6 +321,8 @@
 			clock-names = "dsi", "parent";
 			resets = <&tegra_car 48>;
 			reset-names = "dsi";
+			power-domains = <&pd_core>;
+			operating-points-v2 = <&dsia_dvfs_opp_table>;
 			status = "disabled";
 		};
 
@@ -298,6 +334,8 @@
 			clock-names = "dsi", "parent";
 			resets = <&tegra_car 84>;
 			reset-names = "dsi";
+			power-domains = <&pd_core>;
+			operating-points-v2 = <&dsib_dvfs_opp_table>;
 			status = "disabled";
 		};
 	};
@@ -358,6 +396,34 @@
 		reg = <0x60006000 0x1000>;
 		#clock-cells = <1>;
 		#reset-cells = <1>;
+
+		sclk {
+			compatible = "nvidia,tegra30-sclk";
+			clocks = <&tegra_car TEGRA30_CLK_SCLK>;
+			power-domains = <&pd_core>;
+			operating-points-v2 = <&sclk_dvfs_opp_table>;
+		};
+
+		pll-c {
+			compatible = "nvidia,tegra30-pllc";
+			clocks = <&tegra_car TEGRA30_CLK_PLL_C>;
+			power-domains = <&pd_core>;
+			operating-points-v2 = <&pll_c_dvfs_opp_table>;
+		};
+
+		pll-e {
+			compatible = "nvidia,tegra30-plle";
+			clocks = <&tegra_car TEGRA30_CLK_PLL_E>;
+			power-domains = <&pd_core>;
+			operating-points-v2 = <&pll_e_dvfs_opp_table>;
+		};
+
+		pll-m {
+			compatible = "nvidia,tegra30-pllm";
+			clocks = <&tegra_car TEGRA30_CLK_PLL_M>;
+			power-domains = <&pd_core>;
+			operating-points-v2 = <&pll_m_dvfs_opp_table>;
+		};
 	};
 
 	flow-controller@60007000 {
@@ -441,9 +507,7 @@
 		gpio-controller;
 		#interrupt-cells = <2>;
 		interrupt-controller;
-		/*
 		gpio-ranges = <&pinmux 0 0 248>;
-		*/
 	};
 
 	vde@6001a000 {
@@ -468,6 +532,8 @@
 		reset-names = "vde", "mc";
 		resets = <&tegra_car 61>, <&mc TEGRA30_MC_RESET_VDE>;
 		iommus = <&mc TEGRA_SWGROUP_VDE>;
+		power-domains = <&pd_vde>;
+		operating-points-v2 = <&vde_dvfs_opp_table>;
 	};
 
 	apbmisc@70000800 {
@@ -565,6 +631,8 @@
 		clock-names = "gmi";
 		resets = <&tegra_car 42>;
 		reset-names = "gmi";
+		power-domains = <&pd_core>;
+		operating-points-v2 = <&nor_dvfs_opp_table>;
 		status = "disabled";
 	};
 
@@ -575,6 +643,8 @@
 		clocks = <&tegra_car TEGRA30_CLK_PWM>;
 		resets = <&tegra_car 17>;
 		reset-names = "pwm";
+		power-domains = <&pd_core>;
+		operating-points-v2 = <&pwm_dvfs_opp_table>;
 		status = "disabled";
 	};
 
@@ -666,7 +736,7 @@
 	};
 
 	spi@7000d400 {
-		compatible = "nvidia,tegra30-slink", "nvidia,tegra20-slink";
+		compatible = "nvidia,tegra30-slink";
 		reg = <0x7000d400 0x200>;
 		interrupts = <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>;
 		#address-cells = <1>;
@@ -676,11 +746,13 @@
 		reset-names = "spi";
 		dmas = <&apbdma 15>, <&apbdma 15>;
 		dma-names = "rx", "tx";
+		power-domains = <&pd_core>;
+		operating-points-v2 = <&sbc1_dvfs_opp_table>;
 		status = "disabled";
 	};
 
 	spi@7000d600 {
-		compatible = "nvidia,tegra30-slink", "nvidia,tegra20-slink";
+		compatible = "nvidia,tegra30-slink";
 		reg = <0x7000d600 0x200>;
 		interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
 		#address-cells = <1>;
@@ -690,11 +762,13 @@
 		reset-names = "spi";
 		dmas = <&apbdma 16>, <&apbdma 16>;
 		dma-names = "rx", "tx";
+		power-domains = <&pd_core>;
+		operating-points-v2 = <&sbc2_dvfs_opp_table>;
 		status = "disabled";
 	};
 
 	spi@7000d800 {
-		compatible = "nvidia,tegra30-slink", "nvidia,tegra20-slink";
+		compatible = "nvidia,tegra30-slink";
 		reg = <0x7000d800 0x200>;
 		interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
 		#address-cells = <1>;
@@ -704,11 +778,13 @@
 		reset-names = "spi";
 		dmas = <&apbdma 17>, <&apbdma 17>;
 		dma-names = "rx", "tx";
+		power-domains = <&pd_core>;
+		operating-points-v2 = <&sbc3_dvfs_opp_table>;
 		status = "disabled";
 	};
 
 	spi@7000da00 {
-		compatible = "nvidia,tegra30-slink", "nvidia,tegra20-slink";
+		compatible = "nvidia,tegra30-slink";
 		reg = <0x7000da00 0x200>;
 		interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>;
 		#address-cells = <1>;
@@ -718,11 +794,13 @@
 		reset-names = "spi";
 		dmas = <&apbdma 18>, <&apbdma 18>;
 		dma-names = "rx", "tx";
+		power-domains = <&pd_core>;
+		operating-points-v2 = <&sbc4_dvfs_opp_table>;
 		status = "disabled";
 	};
 
 	spi@7000dc00 {
-		compatible = "nvidia,tegra30-slink", "nvidia,tegra20-slink";
+		compatible = "nvidia,tegra30-slink";
 		reg = <0x7000dc00 0x200>;
 		interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>;
 		#address-cells = <1>;
@@ -732,11 +810,13 @@
 		reset-names = "spi";
 		dmas = <&apbdma 27>, <&apbdma 27>;
 		dma-names = "rx", "tx";
+		power-domains = <&pd_core>;
+		operating-points-v2 = <&sbc5_dvfs_opp_table>;
 		status = "disabled";
 	};
 
 	spi@7000de00 {
-		compatible = "nvidia,tegra30-slink", "nvidia,tegra20-slink";
+		compatible = "nvidia,tegra30-slink";
 		reg = <0x7000de00 0x200>;
 		interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
 		#address-cells = <1>;
@@ -746,6 +826,8 @@
 		reset-names = "spi";
 		dmas = <&apbdma 28>, <&apbdma 28>;
 		dma-names = "rx", "tx";
+		power-domains = <&pd_core>;
+		operating-points-v2 = <&sbc6_dvfs_opp_table>;
 		status = "disabled";
 	};
 
@@ -765,6 +847,72 @@
 		clocks = <&tegra_car TEGRA30_CLK_PCLK>, <&clk32k_in>;
 		clock-names = "pclk", "clk32k_in";
 		#clock-cells = <1>;
+
+		pd_core: core-domain {
+			#power-domain-cells = <0>;
+			operating-points-v2 = <&core_opp_table>;
+		};
+
+		powergates {
+			pd_3d0: td {
+				clocks = <&tegra_car TEGRA30_CLK_GR3D>;
+				resets = <&mc TEGRA30_MC_RESET_3D>,
+					 <&tegra_car TEGRA30_CLK_GR3D>;
+				power-domains = <&pd_core>;
+				#power-domain-cells = <0>;
+			};
+
+			pd_3d1: td2 {
+				clocks = <&tegra_car TEGRA30_CLK_GR3D2>;
+				resets = <&mc TEGRA30_MC_RESET_3D2>,
+					 <&tegra_car TEGRA30_CLK_GR3D2>;
+				power-domains = <&pd_core>;
+				#power-domain-cells = <0>;
+			};
+
+			pd_venc: venc {
+				clocks = <&tegra_car TEGRA30_CLK_ISP>,
+					 <&tegra_car TEGRA30_CLK_VI>,
+					 <&tegra_car TEGRA30_CLK_CSI>;
+				resets = <&mc TEGRA30_MC_RESET_ISP>,
+					 <&mc TEGRA30_MC_RESET_VI>,
+					 <&tegra_car TEGRA30_CLK_ISP>,
+					 <&tegra_car 20 /* VI */>,
+					 <&tegra_car TEGRA30_CLK_CSI>;
+				power-domains = <&pd_core>;
+				#power-domain-cells = <0>;
+			};
+
+			pd_vde: vdec {
+				clocks = <&tegra_car TEGRA30_CLK_VDE>;
+				resets = <&mc TEGRA30_MC_RESET_VDE>,
+					 <&tegra_car TEGRA30_CLK_VDE>;
+				power-domains = <&pd_core>;
+				#power-domain-cells = <0>;
+			};
+
+			pd_mpe: mpe {
+				clocks = <&tegra_car TEGRA30_CLK_MPE>;
+				resets = <&mc TEGRA30_MC_RESET_MPE>,
+					 <&tegra_car TEGRA30_CLK_MPE>;
+				power-domains = <&pd_core>;
+				#power-domain-cells = <0>;
+			};
+
+			pd_heg: heg {
+				clocks = <&tegra_car TEGRA30_CLK_GR2D>,
+					 <&tegra_car TEGRA30_CLK_EPP>,
+					 <&tegra_car TEGRA30_CLK_HOST1X>;
+				resets = <&mc TEGRA30_MC_RESET_2D>,
+					 <&mc TEGRA30_MC_RESET_EPP>,
+					 <&mc TEGRA30_MC_RESET_HC>,
+					 <&tegra_car TEGRA30_CLK_GR2D>,
+					 <&tegra_car TEGRA30_CLK_EPP>,
+					 <&tegra_car TEGRA30_CLK_HOST1X>;
+				power-domains = <&pd_core>;
+				#power-domain-cells = <0>;
+			};
+		};
 	};
 
 	mc: memory-controller@7000f000 {
@@ -785,6 +933,7 @@
 		reg = <0x7000f400 0x400>;
 		interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&tegra_car TEGRA30_CLK_EMC>;
+		power-domains = <&pd_core>;
 
 		nvidia,memory-controller = <&mc>;
 		operating-points-v2 = <&emc_icc_dvfs_opp_table>;
@@ -799,6 +948,8 @@
 		clock-names = "fuse";
 		resets = <&tegra_car 39>;
 		reset-names = "fuse";
+		power-domains = <&pd_core>;
+		operating-points-v2 = <&fuse_burn_dvfs_opp_table>;
 	};
 
 	tsensor: tsensor@70014000 {
@@ -921,6 +1072,8 @@
 		clock-names = "sdhci";
 		resets = <&tegra_car 14>;
 		reset-names = "sdhci";
+		power-domains = <&pd_core>;
+		operating-points-v2 = <&sdmmc1_dvfs_opp_table>;
 		status = "disabled";
 	};
 
@@ -943,6 +1096,8 @@
 		clock-names = "sdhci";
 		resets = <&tegra_car 69>;
 		reset-names = "sdhci";
+		power-domains = <&pd_core>;
+		operating-points-v2 = <&sdmmc3_dvfs_opp_table>;
 		status = "disabled";
 	};
 
@@ -967,6 +1122,8 @@
 		reset-names = "usb";
 		nvidia,needs-double-reset;
 		nvidia,phy = <&phy1>;
+		power-domains = <&pd_core>;
+		operating-points-v2 = <&usbd_dvfs_opp_table>;
 		status = "disabled";
 	};
 
@@ -1008,6 +1165,8 @@
 		resets = <&tegra_car 58>;
 		reset-names = "usb";
 		nvidia,phy = <&phy2>;
+		power-domains = <&pd_core>;
+		operating-points-v2 = <&usb2_dvfs_opp_table>;
 		status = "disabled";
 	};
 
@@ -1048,6 +1207,8 @@
 		resets = <&tegra_car 59>;
 		reset-names = "usb";
 		nvidia,phy = <&phy3>;
+		power-domains = <&pd_core>;
+		operating-points-v2 = <&usb3_dvfs_opp_table>;
 		status = "disabled";
 	};
 
diff --git a/arch/arm/boot/dts/uniphier-ld4-ref.dts b/arch/arm/boot/dts/uniphier-ld4-ref.dts
index c46c2e8a10a7..e007db084787 100644
--- a/arch/arm/boot/dts/uniphier-ld4-ref.dts
+++ b/arch/arm/boot/dts/uniphier-ld4-ref.dts
@@ -36,11 +36,11 @@
 };
 
 &ethsc {
-	interrupts = <1 8>;
+	interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
 };
 
 &serialsc {
-	interrupts = <1 8>;
+	interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
 };
 
 &serial0 {
@@ -56,7 +56,7 @@
 };
 
 &gpio {
-	xirq1 {
+	xirq1-hog {
 		gpio-hog;
 		gpios = <UNIPHIER_GPIO_IRQ(1) 0>;
 		input;
diff --git a/arch/arm/boot/dts/uniphier-ld4.dtsi b/arch/arm/boot/dts/uniphier-ld4.dtsi
index b52957ccda0d..9dceff12a633 100644
--- a/arch/arm/boot/dts/uniphier-ld4.dtsi
+++ b/arch/arm/boot/dts/uniphier-ld4.dtsi
@@ -6,6 +6,7 @@
 //   Author: Masahiro Yamada <yamada.masahiro@socionext.com>
 
 #include <dt-bindings/gpio/uniphier-gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
 
 / {
 	compatible = "socionext,uniphier-ld4";
@@ -55,7 +56,8 @@
 			compatible = "socionext,uniphier-system-cache";
 			reg = <0x500c0000 0x2000>, <0x503c0100 0x4>,
 			      <0x506c0000 0x400>;
-			interrupts = <0 174 4>, <0 175 4>;
+			interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 175 IRQ_TYPE_LEVEL_HIGH>;
 			cache-unified;
 			cache-size = <(512 * 1024)>;
 			cache-sets = <256>;
@@ -69,7 +71,7 @@
 			reg = <0x54006000 0x100>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 39 4>;
+			interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_spi0>;
 			clocks = <&peri_clk 11>;
@@ -80,7 +82,7 @@
 			compatible = "socionext,uniphier-uart";
 			status = "disabled";
 			reg = <0x54006800 0x40>;
-			interrupts = <0 33 4>;
+			interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_uart0>;
 			clocks = <&peri_clk 0>;
@@ -91,7 +93,7 @@
 			compatible = "socionext,uniphier-uart";
 			status = "disabled";
 			reg = <0x54006900 0x40>;
-			interrupts = <0 35 4>;
+			interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_uart1>;
 			clocks = <&peri_clk 1>;
@@ -102,7 +104,7 @@
 			compatible = "socionext,uniphier-uart";
 			status = "disabled";
 			reg = <0x54006a00 0x40>;
-			interrupts = <0 37 4>;
+			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_uart2>;
 			clocks = <&peri_clk 2>;
@@ -113,7 +115,7 @@
 			compatible = "socionext,uniphier-uart";
 			status = "disabled";
 			reg = <0x54006b00 0x40>;
-			interrupts = <0 29 4>;
+			interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_uart3>;
 			clocks = <&peri_clk 3>;
@@ -140,7 +142,7 @@
 			reg = <0x58400000 0x40>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 41 1>;
+			interrupts = <GIC_SPI 41 IRQ_TYPE_EDGE_RISING>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_i2c0>;
 			clocks = <&peri_clk 4>;
@@ -154,7 +156,7 @@
 			reg = <0x58480000 0x40>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 42 1>;
+			interrupts = <GIC_SPI 42 IRQ_TYPE_EDGE_RISING>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_i2c1>;
 			clocks = <&peri_clk 5>;
@@ -168,7 +170,7 @@
 			reg = <0x58500000 0x40>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 43 1>;
+			interrupts = <GIC_SPI 43 IRQ_TYPE_EDGE_RISING>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_i2c2>;
 			clocks = <&peri_clk 6>;
@@ -182,7 +184,7 @@
 			reg = <0x58580000 0x40>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 44 1>;
+			interrupts = <GIC_SPI 44 IRQ_TYPE_EDGE_RISING>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_i2c3>;
 			clocks = <&peri_clk 7>;
@@ -240,8 +242,13 @@
 		dmac: dma-controller@5a000000 {
 			compatible = "socionext,uniphier-mio-dmac";
 			reg = <0x5a000000 0x1000>;
-			interrupts = <0 68 4>, <0 68 4>, <0 69 4>, <0 70 4>,
-				     <0 71 4>, <0 72 4>, <0 73 4>;
+			interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&mio_clk 7>;
 			resets = <&mio_rst 7>;
 			#dma-cells = <1>;
@@ -251,7 +258,7 @@
 			compatible = "socionext,uniphier-sd-v2.91";
 			status = "disabled";
 			reg = <0x5a400000 0x200>;
-			interrupts = <0 76 4>;
+			interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default", "uhs";
 			pinctrl-0 = <&pinctrl_sd>;
 			pinctrl-1 = <&pinctrl_sd_uhs>;
@@ -271,7 +278,7 @@
 			compatible = "socionext,uniphier-sd-v2.91";
 			status = "disabled";
 			reg = <0x5a500000 0x200>;
-			interrupts = <0 78 4>;
+			interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_emmc>;
 			clocks = <&mio_clk 1>;
@@ -289,7 +296,7 @@
 			compatible = "socionext,uniphier-ehci", "generic-ehci";
 			status = "disabled";
 			reg = <0x5a800100 0x100>;
-			interrupts = <0 80 4>;
+			interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_usb0>;
 			clocks = <&sys_clk 8>, <&mio_clk 7>, <&mio_clk 8>,
@@ -303,7 +310,7 @@
 			compatible = "socionext,uniphier-ehci", "generic-ehci";
 			status = "disabled";
 			reg = <0x5a810100 0x100>;
-			interrupts = <0 81 4>;
+			interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_usb1>;
 			clocks = <&sys_clk 8>, <&mio_clk 7>, <&mio_clk 9>,
@@ -317,7 +324,7 @@
 			compatible = "socionext,uniphier-ehci", "generic-ehci";
 			status = "disabled";
 			reg = <0x5a820100 0x100>;
-			interrupts = <0 82 4>;
+			interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_usb2>;
 			clocks = <&sys_clk 8>, <&mio_clk 7>, <&mio_clk 10>,
@@ -358,14 +365,16 @@
 		timer@60000200 {
 			compatible = "arm,cortex-a9-global-timer";
 			reg = <0x60000200 0x20>;
-			interrupts = <1 11 0x104>;
+			interrupts = <GIC_PPI 11
+				(GIC_CPU_MASK_RAW(1) | IRQ_TYPE_LEVEL_HIGH)>;
 			clocks = <&arm_timer_clk>;
 		};
 
 		timer@60000600 {
 			compatible = "arm,cortex-a9-twd-timer";
 			reg = <0x60000600 0x20>;
-			interrupts = <1 13 0x104>;
+			interrupts = <GIC_PPI 13
+				(GIC_CPU_MASK_RAW(1) | IRQ_TYPE_LEVEL_HIGH)>;
 			clocks = <&arm_timer_clk>;
 		};
 
@@ -407,7 +416,7 @@
 			reg = <0x68000000 0x20>, <0x68100000 0x1000>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 65 4>;
+			interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_nand>;
 			clock-names = "nand", "nand_x", "ecc";
diff --git a/arch/arm/boot/dts/uniphier-ld6b-ref.dts b/arch/arm/boot/dts/uniphier-ld6b-ref.dts
index 5bc7fe11b517..223a78b4a761 100644
--- a/arch/arm/boot/dts/uniphier-ld6b-ref.dts
+++ b/arch/arm/boot/dts/uniphier-ld6b-ref.dts
@@ -40,11 +40,11 @@
 };
 
 &ethsc {
-	interrupts = <4 8>;
+	interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
 };
 
 &serialsc {
-	interrupts = <4 8>;
+	interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
 };
 
 &serial0 {
@@ -60,7 +60,7 @@
 };
 
 &gpio {
-	xirq4 {
+	xirq4-hog {
 		gpio-hog;
 		gpios = <UNIPHIER_GPIO_IRQ(4) 0>;
 		input;
diff --git a/arch/arm/boot/dts/uniphier-pinctrl.dtsi b/arch/arm/boot/dts/uniphier-pinctrl.dtsi
index c0fd029b37e5..f909ec2e5333 100644
--- a/arch/arm/boot/dts/uniphier-pinctrl.dtsi
+++ b/arch/arm/boot/dts/uniphier-pinctrl.dtsi
@@ -196,11 +196,21 @@
 		function = "usb0";
 	};
 
+	pinctrl_usb0_device: usb0-device {
+		groups = "usb0_device";
+		function = "usb0";
+	};
+
 	pinctrl_usb1: usb1 {
 		groups = "usb1";
 		function = "usb1";
 	};
 
+	pinctrl_usb1_device: usb1-device {
+		groups = "usb1_device";
+		function = "usb1";
+	};
+
 	pinctrl_usb2: usb2 {
 		groups = "usb2";
 		function = "usb2";
diff --git a/arch/arm/boot/dts/uniphier-pro4-ace.dts b/arch/arm/boot/dts/uniphier-pro4-ace.dts
index 27ff2b7b9d0e..6baee4410d9c 100644
--- a/arch/arm/boot/dts/uniphier-pro4-ace.dts
+++ b/arch/arm/boot/dts/uniphier-pro4-ace.dts
@@ -99,3 +99,11 @@
 &usb1 {
 	status = "okay";
 };
+
+&ahci0 {
+	status = "okay";
+};
+
+&ahci1 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/uniphier-pro4-ref.dts b/arch/arm/boot/dts/uniphier-pro4-ref.dts
index 3b9b61314d01..d2ce5c039865 100644
--- a/arch/arm/boot/dts/uniphier-pro4-ref.dts
+++ b/arch/arm/boot/dts/uniphier-pro4-ref.dts
@@ -39,11 +39,11 @@
 };
 
 &ethsc {
-	interrupts = <2 8>;
+	interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
 };
 
 &serialsc {
-	interrupts = <2 8>;
+	interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
 };
 
 &serial0 {
@@ -59,7 +59,7 @@
 };
 
 &gpio {
-	xirq2 {
+	xirq2-hog {
 		gpio-hog;
 		gpios = <UNIPHIER_GPIO_IRQ(2) 0>;
 		input;
@@ -108,3 +108,11 @@
 		reg = <0>;
 	};
 };
+
+&ahci0 {
+	status = "okay";
+};
+
+&ahci1 {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/uniphier-pro4.dtsi b/arch/arm/boot/dts/uniphier-pro4.dtsi
index a53b73ee93e9..a309e64c57c8 100644
--- a/arch/arm/boot/dts/uniphier-pro4.dtsi
+++ b/arch/arm/boot/dts/uniphier-pro4.dtsi
@@ -6,6 +6,7 @@
 //   Author: Masahiro Yamada <yamada.masahiro@socionext.com>
 
 #include <dt-bindings/gpio/uniphier-gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
 
 / {
 	compatible = "socionext,uniphier-pro4";
@@ -63,7 +64,8 @@
 			compatible = "socionext,uniphier-system-cache";
 			reg = <0x500c0000 0x2000>, <0x503c0100 0x4>,
 			      <0x506c0000 0x400>;
-			interrupts = <0 174 4>, <0 175 4>;
+			interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 175 IRQ_TYPE_LEVEL_HIGH>;
 			cache-unified;
 			cache-size = <(768 * 1024)>;
 			cache-sets = <256>;
@@ -77,7 +79,7 @@
 			reg = <0x54006000 0x100>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 39 4>;
+			interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_spi0>;
 			clocks = <&peri_clk 11>;
@@ -88,7 +90,7 @@
 			compatible = "socionext,uniphier-uart";
 			status = "disabled";
 			reg = <0x54006800 0x40>;
-			interrupts = <0 33 4>;
+			interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_uart0>;
 			clocks = <&peri_clk 0>;
@@ -99,7 +101,7 @@
 			compatible = "socionext,uniphier-uart";
 			status = "disabled";
 			reg = <0x54006900 0x40>;
-			interrupts = <0 35 4>;
+			interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_uart1>;
 			clocks = <&peri_clk 1>;
@@ -110,7 +112,7 @@
 			compatible = "socionext,uniphier-uart";
 			status = "disabled";
 			reg = <0x54006a00 0x40>;
-			interrupts = <0 37 4>;
+			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_uart2>;
 			clocks = <&peri_clk 2>;
@@ -121,7 +123,7 @@
 			compatible = "socionext,uniphier-uart";
 			status = "disabled";
 			reg = <0x54006b00 0x40>;
-			interrupts = <0 177 4>;
+			interrupts = <GIC_SPI 177 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_uart3>;
 			clocks = <&peri_clk 3>;
@@ -148,7 +150,7 @@
 			reg = <0x58780000 0x80>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 41 4>;
+			interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_i2c0>;
 			clocks = <&peri_clk 4>;
@@ -162,7 +164,7 @@
 			reg = <0x58781000 0x80>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 42 4>;
+			interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_i2c1>;
 			clocks = <&peri_clk 5>;
@@ -176,7 +178,7 @@
 			reg = <0x58782000 0x80>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 43 4>;
+			interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_i2c2>;
 			clocks = <&peri_clk 6>;
@@ -190,7 +192,7 @@
 			reg = <0x58783000 0x80>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 44 4>;
+			interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_i2c3>;
 			clocks = <&peri_clk 7>;
@@ -206,7 +208,7 @@
 			reg = <0x58785000 0x80>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 25 4>;
+			interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&peri_clk 9>;
 			resets = <&peri_rst 9>;
 			clock-frequency = <400000>;
@@ -218,7 +220,7 @@
 			reg = <0x58786000 0x80>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 26 4>;
+			interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&peri_clk 10>;
 			resets = <&peri_rst 10>;
 			clock-frequency = <400000>;
@@ -274,8 +276,14 @@
 		dmac: dma-controller@5a000000 {
 			compatible = "socionext,uniphier-mio-dmac";
 			reg = <0x5a000000 0x1000>;
-			interrupts = <0 68 4>, <0 68 4>, <0 69 4>, <0 70 4>,
-				     <0 71 4>, <0 72 4>, <0 73 4>, <0 74 4>;
+			interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&mio_clk 7>;
 			resets = <&mio_rst 7>;
 			#dma-cells = <1>;
@@ -285,7 +293,7 @@
 			compatible = "socionext,uniphier-sd-v2.91";
 			status = "disabled";
 			reg = <0x5a400000 0x200>;
-			interrupts = <0 76 4>;
+			interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default", "uhs";
 			pinctrl-0 = <&pinctrl_sd>;
 			pinctrl-1 = <&pinctrl_sd_uhs>;
@@ -305,7 +313,7 @@
 			compatible = "socionext,uniphier-sd-v2.91";
 			status = "disabled";
 			reg = <0x5a500000 0x200>;
-			interrupts = <0 78 4>;
+			interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_emmc>;
 			clocks = <&mio_clk 1>;
@@ -323,7 +331,7 @@
 			compatible = "socionext,uniphier-sd-v2.91";
 			status = "disabled";
 			reg = <0x5a600000 0x200>;
-			interrupts = <0 85 4>;
+			interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_sd1>;
 			clocks = <&mio_clk 2>;
@@ -339,7 +347,7 @@
 			compatible = "socionext,uniphier-ehci", "generic-ehci";
 			status = "disabled";
 			reg = <0x5a800100 0x100>;
-			interrupts = <0 80 4>;
+			interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_usb2>;
 			clocks = <&sys_clk 8>, <&mio_clk 7>, <&mio_clk 8>,
@@ -355,7 +363,7 @@
 			compatible = "socionext,uniphier-ehci", "generic-ehci";
 			status = "disabled";
 			reg = <0x5a810100 0x100>;
-			interrupts = <0 81 4>;
+			interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_usb3>;
 			clocks = <&sys_clk 8>, <&mio_clk 7>, <&mio_clk 9>,
@@ -376,7 +384,7 @@
 				compatible = "socionext,uniphier-pro4-pinctrl";
 			};
 
-			usb-phy {
+			usb-controller {
 				compatible = "socionext,uniphier-pro4-usb2-phy";
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -403,6 +411,11 @@
 					vbus-supply = <&usb1_vbus>;
 				};
 			};
+
+			sg_clk: clock {
+				compatible = "socionext,uniphier-pro4-sg-clock";
+				#clock-cells = <1>;
+			};
 		};
 
 		soc-glue@5f900000 {
@@ -431,7 +444,7 @@
 		xdmac: dma-controller@5fc10000 {
 			compatible = "socionext,uniphier-xdmac";
 			reg = <0x5fc10000 0x5300>;
-			interrupts = <0 188 4>;
+			interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>;
 			dma-channels = <16>;
 			#dma-cells = <2>;
 		};
@@ -446,14 +459,16 @@
 		timer@60000200 {
 			compatible = "arm,cortex-a9-global-timer";
 			reg = <0x60000200 0x20>;
-			interrupts = <1 11 0x304>;
+			interrupts = <GIC_PPI 11
+				(GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_HIGH)>;
 			clocks = <&arm_timer_clk>;
 		};
 
 		timer@60000600 {
 			compatible = "arm,cortex-a9-twd-timer";
 			reg = <0x60000600 0x20>;
-			interrupts = <1 13 0x304>;
+			interrupts = <GIC_PPI 13
+				(GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_HIGH)>;
 			clocks = <&arm_timer_clk>;
 		};
 
@@ -485,7 +500,7 @@
 			compatible = "socionext,uniphier-pro4-ave4";
 			status = "disabled";
 			reg = <0x65000000 0x8500>;
-			interrupts = <0 66 4>;
+			interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_ether_rgmii>;
 			clock-names = "gio", "ether", "ether-gb", "ether-phy";
@@ -503,12 +518,105 @@
 			};
 		};
 
+		ahci0: sata@65600000 {
+			compatible = "socionext,uniphier-pro4-ahci",
+				     "generic-ahci";
+			status = "disabled";
+			reg = <0x65600000 0x10000>;
+			interrupts = <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&sys_clk 12>, <&sys_clk 28>;
+			resets = <&sys_rst 12>, <&sys_rst 28>, <&ahci0_rst 3>;
+			ports-implemented = <1>;
+			phys = <&ahci0_phy>;
+			assigned-clocks = <&sg_clk 0>;
+			assigned-clock-rates = <25000000>;
+		};
+
+		sata-controller@65700000 {
+			compatible = "socionext,uniphier-pxs2-ahci-glue",
+				     "simple-mfd";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x65700000 0x100>;
+
+			ahci0_rst: reset-controller@0 {
+				compatible = "socionext,uniphier-pro4-ahci-reset";
+				reg = <0x0 0x4>;
+				clock-names = "gio", "link";
+				clocks = <&sys_clk 12>, <&sys_clk 28>;
+				reset-names = "gio", "link";
+				resets = <&sys_rst 12>, <&sys_rst 28>;
+				#reset-cells = <1>;
+			};
+
+			ahci0_phy: sata-phy@10 {
+				compatible = "socionext,uniphier-pro4-ahci-phy";
+				reg = <0x10 0x40>;
+				clock-names = "link", "gio";
+				clocks = <&sys_clk 28>, <&sys_clk 12>;
+				reset-names = "link", "gio", "phy",
+					      "pm", "tx", "rx";
+				resets = <&sys_rst 28>, <&sys_rst 12>,
+					 <&sys_rst 30>,
+					 <&ahci0_rst 0>, <&ahci0_rst 1>,
+					 <&ahci0_rst 2>;
+				#phy-cells = <0>;
+			};
+		};
+
+		ahci1: sata@65800000 {
+			compatible = "socionext,uniphier-pro4-ahci",
+				     "generic-ahci";
+			status = "disabled";
+			reg = <0x65800000 0x10000>;
+			interrupts = <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&sys_clk 12>, <&sys_clk 29>;
+			resets = <&sys_rst 12>, <&sys_rst 29>, <&ahci1_rst 3>;
+			ports-implemented = <1>;
+			phys = <&ahci1_phy>;
+			assigned-clocks = <&sg_clk 0>;
+			assigned-clock-rates = <25000000>;
+		};
+
+		sata-controller@65900000 {
+			compatible = "socionext,uniphier-pro4-ahci-glue",
+				     "simple-mfd";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x65900000 0x100>;
+
+			ahci1_rst: reset-controller@0 {
+				compatible = "socionext,uniphier-pro4-ahci-reset";
+				reg = <0x0 0x4>;
+				clock-names = "gio", "link";
+				clocks = <&sys_clk 12>, <&sys_clk 29>;
+				reset-names = "gio", "link";
+				resets = <&sys_rst 12>, <&sys_rst 29>;
+				#reset-cells = <1>;
+			};
+
+			ahci1_phy: sata-phy@10 {
+				compatible = "socionext,uniphier-pro4-ahci-phy";
+				reg = <0x10 0x40>;
+				clock-names = "link", "gio";
+				clocks = <&sys_clk 29>, <&sys_clk 12>;
+				reset-names = "link", "gio", "phy",
+					      "pm", "tx", "rx";
+				resets = <&sys_rst 29>, <&sys_rst 12>,
+					 <&sys_rst 30>,
+					 <&ahci1_rst 0>, <&ahci1_rst 1>,
+					 <&ahci1_rst 2>;
+				#phy-cells = <0>;
+			};
+		};
+
 		usb0: usb@65a00000 {
 			compatible = "socionext,uniphier-dwc3", "snps,dwc3";
 			status = "disabled";
 			reg = <0x65a00000 0xcd00>;
 			interrupt-names = "host", "peripheral";
-			interrupts = <0 134 4>, <0 135 4>;
+			interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_usb0>;
 			clock-names = "ref", "bus_early", "suspend";
@@ -518,7 +626,7 @@
 			dr_mode = "host";
 		};
 
-		usb-glue@65b00000 {
+		usb-controller@65b00000 {
 			compatible = "socionext,uniphier-pro4-dwc3-glue",
 				     "simple-mfd";
 			#address-cells = <1>;
@@ -561,7 +669,8 @@
 			status = "disabled";
 			reg = <0x65c00000 0xcd00>;
 			interrupt-names = "host", "peripheral";
-			interrupts = <0 137 4>, <0 138 4>;
+			interrupts = <GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_usb1>;
 			clock-names = "ref", "bus_early", "suspend";
@@ -571,7 +680,7 @@
 			dr_mode = "host";
 		};
 
-		usb-glue@65d00000 {
+		usb-controller@65d00000 {
 			compatible = "socionext,uniphier-pro4-dwc3-glue",
 				     "simple-mfd";
 			#address-cells = <1>;
@@ -605,7 +714,7 @@
 			reg = <0x68000000 0x20>, <0x68100000 0x1000>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 65 4>;
+			interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_nand>;
 			clock-names = "nand", "nand_x", "ecc";
diff --git a/arch/arm/boot/dts/uniphier-pro5.dtsi b/arch/arm/boot/dts/uniphier-pro5.dtsi
index 3525125832dd..100edd7438d8 100644
--- a/arch/arm/boot/dts/uniphier-pro5.dtsi
+++ b/arch/arm/boot/dts/uniphier-pro5.dtsi
@@ -5,6 +5,8 @@
 // Copyright (C) 2015-2016 Socionext Inc.
 //   Author: Masahiro Yamada <yamada.masahiro@socionext.com>
 
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
 / {
 	compatible = "socionext,uniphier-pro5";
 	#address-cells = <1>;
@@ -135,7 +137,8 @@
 			compatible = "socionext,uniphier-system-cache";
 			reg = <0x500c0000 0x2000>, <0x503c0100 0x8>,
 			      <0x506c0000 0x400>;
-			interrupts = <0 190 4>, <0 191 4>;
+			interrupts = <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 191 IRQ_TYPE_LEVEL_HIGH>;
 			cache-unified;
 			cache-size = <(2 * 1024 * 1024)>;
 			cache-sets = <512>;
@@ -148,7 +151,8 @@
 			compatible = "socionext,uniphier-system-cache";
 			reg = <0x500c8000 0x2000>, <0x503c8100 0x8>,
 			      <0x506c8000 0x400>;
-			interrupts = <0 174 4>, <0 175 4>;
+			interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 175 IRQ_TYPE_LEVEL_HIGH>;
 			cache-unified;
 			cache-size = <(2 * 1024 * 1024)>;
 			cache-sets = <512>;
@@ -162,7 +166,7 @@
 			reg = <0x54006000 0x100>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 39 4>;
+			interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_spi0>;
 			clocks = <&peri_clk 11>;
@@ -175,7 +179,7 @@
 			reg = <0x54006100 0x100>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 216 4>;
+			interrupts = <GIC_SPI 216 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_spi1>;
 			clocks = <&peri_clk 11>;	/* common with spi0 */
@@ -186,7 +190,7 @@
 			compatible = "socionext,uniphier-uart";
 			status = "disabled";
 			reg = <0x54006800 0x40>;
-			interrupts = <0 33 4>;
+			interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_uart0>;
 			clocks = <&peri_clk 0>;
@@ -197,7 +201,7 @@
 			compatible = "socionext,uniphier-uart";
 			status = "disabled";
 			reg = <0x54006900 0x40>;
-			interrupts = <0 35 4>;
+			interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_uart1>;
 			clocks = <&peri_clk 1>;
@@ -208,7 +212,7 @@
 			compatible = "socionext,uniphier-uart";
 			status = "disabled";
 			reg = <0x54006a00 0x40>;
-			interrupts = <0 37 4>;
+			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_uart2>;
 			clocks = <&peri_clk 2>;
@@ -219,7 +223,7 @@
 			compatible = "socionext,uniphier-uart";
 			status = "disabled";
 			reg = <0x54006b00 0x40>;
-			interrupts = <0 177 4>;
+			interrupts = <GIC_SPI 177 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_uart3>;
 			clocks = <&peri_clk 3>;
@@ -246,7 +250,7 @@
 			reg = <0x58780000 0x80>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 41 4>;
+			interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_i2c0>;
 			clocks = <&peri_clk 4>;
@@ -260,7 +264,7 @@
 			reg = <0x58781000 0x80>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 42 4>;
+			interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_i2c1>;
 			clocks = <&peri_clk 5>;
@@ -274,7 +278,7 @@
 			reg = <0x58782000 0x80>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 43 4>;
+			interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_i2c2>;
 			clocks = <&peri_clk 6>;
@@ -288,7 +292,7 @@
 			reg = <0x58783000 0x80>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 44 4>;
+			interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_i2c3>;
 			clocks = <&peri_clk 7>;
@@ -304,7 +308,7 @@
 			reg = <0x58785000 0x80>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 25 4>;
+			interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&peri_clk 9>;
 			resets = <&peri_rst 9>;
 			clock-frequency = <400000>;
@@ -316,7 +320,7 @@
 			reg = <0x58786000 0x80>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 26 4>;
+			interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&peri_clk 10>;
 			resets = <&peri_rst 10>;
 			clock-frequency = <400000>;
@@ -415,7 +419,7 @@
 		xdmac: dma-controller@5fc10000 {
 			compatible = "socionext,uniphier-xdmac";
 			reg = <0x5fc10000 0x5300>;
-			interrupts = <0 188 4>;
+			interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>;
 			dma-channels = <16>;
 			#dma-cells = <2>;
 		};
@@ -430,14 +434,16 @@
 		timer@60000200 {
 			compatible = "arm,cortex-a9-global-timer";
 			reg = <0x60000200 0x20>;
-			interrupts = <1 11 0x304>;
+			interrupts = <GIC_PPI 11
+				(GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_HIGH)>;
 			clocks = <&arm_timer_clk>;
 		};
 
 		timer@60000600 {
 			compatible = "arm,cortex-a9-twd-timer";
 			reg = <0x60000600 0x20>;
-			interrupts = <1 13 0x304>;
+			interrupts = <GIC_PPI 13
+				(GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_HIGH)>;
 			clocks = <&arm_timer_clk>;
 		};
 
@@ -470,7 +476,7 @@
 			status = "disabled";
 			reg = <0x65a00000 0xcd00>;
 			interrupt-names = "host";
-			interrupts = <0 134 4>;
+			interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_usb0>;
 			clock-names = "ref", "bus_early", "suspend";
@@ -480,7 +486,7 @@
 			dr_mode = "host";
 		};
 
-		usb-glue@65b00000 {
+		usb-controller@65b00000 {
 			compatible = "socionext,uniphier-pro5-dwc3-glue",
 				     "simple-mfd";
 			#address-cells = <1>;
@@ -534,7 +540,7 @@
 			status = "disabled";
 			reg = <0x65c00000 0xcd00>;
 			interrupt-names = "host";
-			interrupts = <0 137 4>;
+			interrupts = <GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_usb1>, <&pinctrl_usb2>;
 			clock-names = "ref", "bus_early", "suspend";
@@ -544,7 +550,7 @@
 			dr_mode = "host";
 		};
 
-		usb-glue@65d00000 {
+		usb-controller@65d00000 {
 			compatible = "socionext,uniphier-pro5-dwc3-glue",
 				     "simple-mfd";
 			#address-cells = <1>;
@@ -614,8 +620,7 @@
 		};
 
 		pcie_ep: pcie-ep@66000000 {
-			compatible = "socionext,uniphier-pro5-pcie-ep",
-				     "snps,dw-pcie-ep";
+			compatible = "socionext,uniphier-pro5-pcie-ep";
 			status = "disabled";
 			reg-names = "dbi", "dbi2", "link", "addr_space";
 			reg = <0x66000000 0x1000>, <0x66001000 0x1000>,
@@ -650,7 +655,7 @@
 			reg = <0x68000000 0x20>, <0x68100000 0x1000>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 65 4>;
+			interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_nand>;
 			clock-names = "nand", "nand_x", "ecc";
@@ -663,7 +668,7 @@
 			compatible = "socionext,uniphier-sd-v3.1";
 			status = "disabled";
 			reg = <0x68400000 0x800>;
-			interrupts = <0 78 4>;
+			interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_emmc>;
 			clocks = <&sd_clk 1>;
@@ -679,7 +684,7 @@
 			compatible = "socionext,uniphier-sd-v3.1";
 			status = "disabled";
 			reg = <0x68800000 0x800>;
-			interrupts = <0 76 4>;
+			interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default", "uhs";
 			pinctrl-0 = <&pinctrl_sd>;
 			pinctrl-1 = <&pinctrl_sd_uhs>;
diff --git a/arch/arm/boot/dts/uniphier-pxs2-gentil.dts b/arch/arm/boot/dts/uniphier-pxs2-gentil.dts
index 759384b60663..5f18b926c50a 100644
--- a/arch/arm/boot/dts/uniphier-pxs2-gentil.dts
+++ b/arch/arm/boot/dts/uniphier-pxs2-gentil.dts
@@ -99,3 +99,7 @@
 &usb1 {
 	status = "okay";
 };
+
+&ahci {
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/uniphier-pxs2.dtsi b/arch/arm/boot/dts/uniphier-pxs2.dtsi
index e81e5937a60a..ca4dccf56a67 100644
--- a/arch/arm/boot/dts/uniphier-pxs2.dtsi
+++ b/arch/arm/boot/dts/uniphier-pxs2.dtsi
@@ -6,6 +6,7 @@
 //   Author: Masahiro Yamada <yamada.masahiro@socionext.com>
 
 #include <dt-bindings/gpio/uniphier-gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/thermal/thermal.h>
 
 / {
@@ -161,7 +162,10 @@
 			compatible = "socionext,uniphier-system-cache";
 			reg = <0x500c0000 0x2000>, <0x503c0100 0x8>,
 			      <0x506c0000 0x400>;
-			interrupts = <0 174 4>, <0 175 4>, <0 190 4>, <0 191 4>;
+			interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 175 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 191 IRQ_TYPE_LEVEL_HIGH>;
 			cache-unified;
 			cache-size = <(1280 * 1024)>;
 			cache-sets = <512>;
@@ -175,7 +179,7 @@
 			reg = <0x54006000 0x100>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 39 4>;
+			interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_spi0>;
 			clocks = <&peri_clk 11>;
@@ -188,7 +192,7 @@
 			reg = <0x54006100 0x100>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 216 4>;
+			interrupts = <GIC_SPI 216 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_spi1>;
 			clocks = <&peri_clk 12>;
@@ -199,7 +203,7 @@
 			compatible = "socionext,uniphier-uart";
 			status = "disabled";
 			reg = <0x54006800 0x40>;
-			interrupts = <0 33 4>;
+			interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_uart0>;
 			clocks = <&peri_clk 0>;
@@ -210,7 +214,7 @@
 			compatible = "socionext,uniphier-uart";
 			status = "disabled";
 			reg = <0x54006900 0x40>;
-			interrupts = <0 35 4>;
+			interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_uart1>;
 			clocks = <&peri_clk 1>;
@@ -221,7 +225,7 @@
 			compatible = "socionext,uniphier-uart";
 			status = "disabled";
 			reg = <0x54006a00 0x40>;
-			interrupts = <0 37 4>;
+			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_uart2>;
 			clocks = <&peri_clk 2>;
@@ -232,7 +236,7 @@
 			compatible = "socionext,uniphier-uart";
 			status = "disabled";
 			reg = <0x54006b00 0x40>;
-			interrupts = <0 177 4>;
+			interrupts = <GIC_SPI 177 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_uart3>;
 			clocks = <&peri_clk 3>;
@@ -259,7 +263,7 @@
 		audio@56000000 {
 			compatible = "socionext,uniphier-pxs2-aio";
 			reg = <0x56000000 0x80000>;
-			interrupts = <0 144 4>;
+			interrupts = <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_ain1>,
 				    <&pinctrl_ain2>,
@@ -317,7 +321,7 @@
 			reg = <0x58780000 0x80>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 41 4>;
+			interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_i2c0>;
 			clocks = <&peri_clk 4>;
@@ -331,7 +335,7 @@
 			reg = <0x58781000 0x80>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 42 4>;
+			interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_i2c1>;
 			clocks = <&peri_clk 5>;
@@ -345,7 +349,7 @@
 			reg = <0x58782000 0x80>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 43 4>;
+			interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_i2c2>;
 			clocks = <&peri_clk 6>;
@@ -359,7 +363,7 @@
 			reg = <0x58783000 0x80>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 44 4>;
+			interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_i2c3>;
 			clocks = <&peri_clk 7>;
@@ -373,7 +377,7 @@
 			reg = <0x58784000 0x80>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 45 4>;
+			interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&peri_clk 8>;
 			resets = <&peri_rst 8>;
 			clock-frequency = <400000>;
@@ -385,7 +389,7 @@
 			reg = <0x58785000 0x80>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 25 4>;
+			interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&peri_clk 9>;
 			resets = <&peri_rst 9>;
 			clock-frequency = <400000>;
@@ -397,7 +401,7 @@
 			reg = <0x58786000 0x80>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 26 4>;
+			interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&peri_clk 10>;
 			resets = <&peri_rst 10>;
 			clock-frequency = <400000>;
@@ -454,7 +458,7 @@
 			compatible = "socionext,uniphier-sd-v3.1.1";
 			status = "disabled";
 			reg = <0x5a000000 0x800>;
-			interrupts = <0 78 4>;
+			interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_emmc>;
 			clocks = <&sd_clk 1>;
@@ -470,7 +474,7 @@
 			compatible = "socionext,uniphier-sd-v3.1.1";
 			status = "disabled";
 			reg = <0x5a400000 0x800>;
-			interrupts = <0 76 4>;
+			interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default", "uhs";
 			pinctrl-0 = <&pinctrl_sd>;
 			pinctrl-1 = <&pinctrl_sd_uhs>;
@@ -515,7 +519,7 @@
 		xdmac: dma-controller@5fc10000 {
 			compatible = "socionext,uniphier-xdmac";
 			reg = <0x5fc10000 0x5300>;
-			interrupts = <0 188 4>;
+			interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>;
 			dma-channels = <16>;
 			#dma-cells = <2>;
 		};
@@ -530,14 +534,16 @@
 		timer@60000200 {
 			compatible = "arm,cortex-a9-global-timer";
 			reg = <0x60000200 0x20>;
-			interrupts = <1 11 0xf04>;
+			interrupts = <GIC_PPI 11
+				(GIC_CPU_MASK_RAW(0xf) | IRQ_TYPE_LEVEL_HIGH)>;
 			clocks = <&arm_timer_clk>;
 		};
 
 		timer@60000600 {
 			compatible = "arm,cortex-a9-twd-timer";
 			reg = <0x60000600 0x20>;
-			interrupts = <1 13 0xf04>;
+			interrupts = <GIC_PPI 13
+				(GIC_CPU_MASK_RAW(0xf) | IRQ_TYPE_LEVEL_HIGH)>;
 			clocks = <&arm_timer_clk>;
 		};
 
@@ -564,9 +570,9 @@
 				#reset-cells = <1>;
 			};
 
-			pvtctl: pvtctl {
+			pvtctl: thermal-sensor {
 				compatible = "socionext,uniphier-pxs2-thermal";
-				interrupts = <0 3 4>;
+				interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
 				#thermal-sensor-cells = <0>;
 				socionext,tmod-calibration = <0x0f86 0x6844>;
 			};
@@ -576,7 +582,7 @@
 			compatible = "socionext,uniphier-pxs2-ave4";
 			status = "disabled";
 			reg = <0x65000000 0x8500>;
-			interrupts = <0 66 4>;
+			interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_ether_rgmii>;
 			clock-names = "ether";
@@ -593,12 +599,52 @@
 			};
 		};
 
+		ahci: sata@65600000 {
+			compatible = "socionext,uniphier-pxs2-ahci",
+				     "generic-ahci";
+			status = "disabled";
+			reg = <0x65600000 0x10000>;
+			interrupts = <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&sys_clk 28>;
+			resets = <&sys_rst 28>, <&ahci_rst 0>;
+			ports-implemented = <1>;
+			phys = <&ahci_phy>;
+		};
+
+		sata-controller@65700000 {
+			compatible = "socionext,uniphier-pxs2-ahci-glue",
+				     "simple-mfd";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x65700000 0x100>;
+
+			ahci_rst: reset-controller@0 {
+				compatible = "socionext,uniphier-pxs2-ahci-reset";
+				reg = <0x0 0x4>;
+				clock-names = "link";
+				clocks = <&sys_clk 28>;
+				reset-names = "link";
+				resets = <&sys_rst 28>;
+				#reset-cells = <1>;
+			};
+
+			ahci_phy: sata-phy@10 {
+				compatible = "socionext,uniphier-pxs2-ahci-phy";
+				reg = <0x10 0x10>;
+				clock-names = "link";
+				clocks = <&sys_clk 28>;
+				reset-names = "link", "phy";
+				resets = <&sys_rst 28>, <&sys_rst 30>;
+				#phy-cells = <0>;
+			};
+		};
+
 		usb0: usb@65a00000 {
 			compatible = "socionext,uniphier-dwc3", "snps,dwc3";
 			status = "disabled";
 			reg = <0x65a00000 0xcd00>;
-			interrupt-names = "host", "peripheral";
-			interrupts = <0 134 4>, <0 135 4>;
+			interrupt-names = "dwc_usb3";
+			interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_usb0>, <&pinctrl_usb2>;
 			clock-names = "ref", "bus_early", "suspend";
@@ -609,7 +655,7 @@
 			dr_mode = "host";
 		};
 
-		usb-glue@65b00000 {
+		usb-controller@65b00000 {
 			compatible = "socionext,uniphier-pxs2-dwc3-glue",
 				     "simple-mfd";
 			#address-cells = <1>;
@@ -693,8 +739,8 @@
 			compatible = "socionext,uniphier-dwc3", "snps,dwc3";
 			status = "disabled";
 			reg = <0x65c00000 0xcd00>;
-			interrupt-names = "host", "peripheral";
-			interrupts = <0 137 4>, <0 138 4>;
+			interrupt-names = "dwc_usb3";
+			interrupts = <GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_usb1>, <&pinctrl_usb3>;
 			clock-names = "ref", "bus_early", "suspend";
@@ -704,7 +750,7 @@
 			dr_mode = "host";
 		};
 
-		usb-glue@65d00000 {
+		usb-controller@65d00000 {
 			compatible = "socionext,uniphier-pxs2-dwc3-glue",
 				     "simple-mfd";
 			#address-cells = <1>;
@@ -780,7 +826,7 @@
 			reg = <0x68000000 0x20>, <0x68100000 0x1000>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 65 4>;
+			interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_nand>;
 			clock-names = "nand", "nand_x", "ecc";
diff --git a/arch/arm/boot/dts/uniphier-sld8-ref.dts b/arch/arm/boot/dts/uniphier-sld8-ref.dts
index 6db949ec7411..2446f9e15360 100644
--- a/arch/arm/boot/dts/uniphier-sld8-ref.dts
+++ b/arch/arm/boot/dts/uniphier-sld8-ref.dts
@@ -36,11 +36,11 @@
 };
 
 &ethsc {
-	interrupts = <0 8>;
+	interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
 };
 
 &serialsc {
-	interrupts = <0 8>;
+	interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
 };
 
 &serial0 {
@@ -56,7 +56,7 @@
 };
 
 &gpio {
-	xirq0 {
+	xirq0-hog {
 		gpio-hog;
 		gpios = <UNIPHIER_GPIO_IRQ(0) 0>;
 		input;
diff --git a/arch/arm/boot/dts/uniphier-sld8.dtsi b/arch/arm/boot/dts/uniphier-sld8.dtsi
index 96a766deb8d1..67b12dfe513b 100644
--- a/arch/arm/boot/dts/uniphier-sld8.dtsi
+++ b/arch/arm/boot/dts/uniphier-sld8.dtsi
@@ -6,6 +6,7 @@
 //   Author: Masahiro Yamada <yamada.masahiro@socionext.com>
 
 #include <dt-bindings/gpio/uniphier-gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
 
 / {
 	compatible = "socionext,uniphier-sld8";
@@ -55,7 +56,8 @@
 			compatible = "socionext,uniphier-system-cache";
 			reg = <0x500c0000 0x2000>, <0x503c0100 0x4>,
 			      <0x506c0000 0x400>;
-			interrupts = <0 174 4>, <0 175 4>;
+			interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 175 IRQ_TYPE_LEVEL_HIGH>;
 			cache-unified;
 			cache-size = <(256 * 1024)>;
 			cache-sets = <256>;
@@ -69,7 +71,7 @@
 			reg = <0x54006000 0x100>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 39 4>;
+			interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_spi0>;
 			clocks = <&peri_clk 11>;
@@ -80,7 +82,7 @@
 			compatible = "socionext,uniphier-uart";
 			status = "disabled";
 			reg = <0x54006800 0x40>;
-			interrupts = <0 33 4>;
+			interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_uart0>;
 			clocks = <&peri_clk 0>;
@@ -91,7 +93,7 @@
 			compatible = "socionext,uniphier-uart";
 			status = "disabled";
 			reg = <0x54006900 0x40>;
-			interrupts = <0 35 4>;
+			interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_uart1>;
 			clocks = <&peri_clk 1>;
@@ -102,7 +104,7 @@
 			compatible = "socionext,uniphier-uart";
 			status = "disabled";
 			reg = <0x54006a00 0x40>;
-			interrupts = <0 37 4>;
+			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_uart2>;
 			clocks = <&peri_clk 2>;
@@ -113,7 +115,7 @@
 			compatible = "socionext,uniphier-uart";
 			status = "disabled";
 			reg = <0x54006b00 0x40>;
-			interrupts = <0 29 4>;
+			interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_uart3>;
 			clocks = <&peri_clk 3>;
@@ -144,7 +146,7 @@
 			reg = <0x58400000 0x40>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 41 1>;
+			interrupts = <GIC_SPI 41 IRQ_TYPE_EDGE_RISING>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_i2c0>;
 			clocks = <&peri_clk 4>;
@@ -158,7 +160,7 @@
 			reg = <0x58480000 0x40>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 42 1>;
+			interrupts = <GIC_SPI 42 IRQ_TYPE_EDGE_RISING>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_i2c1>;
 			clocks = <&peri_clk 5>;
@@ -172,7 +174,7 @@
 			reg = <0x58500000 0x40>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 43 1>;
+			interrupts = <GIC_SPI 43 IRQ_TYPE_EDGE_RISING>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_i2c2>;
 			clocks = <&peri_clk 6>;
@@ -186,7 +188,7 @@
 			reg = <0x58580000 0x40>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 44 1>;
+			interrupts = <GIC_SPI 44 IRQ_TYPE_EDGE_RISING>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_i2c3>;
 			clocks = <&peri_clk 7>;
@@ -244,8 +246,13 @@
 		dmac: dma-controller@5a000000 {
 			compatible = "socionext,uniphier-mio-dmac";
 			reg = <0x5a000000 0x1000>;
-			interrupts = <0 68 4>, <0 68 4>, <0 69 4>, <0 70 4>,
-				     <0 71 4>, <0 72 4>, <0 73 4>;
+			interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&mio_clk 7>;
 			resets = <&mio_rst 7>;
 			#dma-cells = <1>;
@@ -255,7 +262,7 @@
 			compatible = "socionext,uniphier-sd-v2.91";
 			status = "disabled";
 			reg = <0x5a400000 0x200>;
-			interrupts = <0 76 4>;
+			interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default", "uhs";
 			pinctrl-0 = <&pinctrl_sd>;
 			pinctrl-1 = <&pinctrl_sd_uhs>;
@@ -275,7 +282,7 @@
 			compatible = "socionext,uniphier-sd-v2.91";
 			status = "disabled";
 			reg = <0x5a500000 0x200>;
-			interrupts = <0 78 4>;
+			interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_emmc>;
 			clocks = <&mio_clk 1>;
@@ -293,7 +300,7 @@
 			compatible = "socionext,uniphier-ehci", "generic-ehci";
 			status = "disabled";
 			reg = <0x5a800100 0x100>;
-			interrupts = <0 80 4>;
+			interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_usb0>;
 			clocks = <&sys_clk 8>, <&mio_clk 7>, <&mio_clk 8>,
@@ -307,7 +314,7 @@
 			compatible = "socionext,uniphier-ehci", "generic-ehci";
 			status = "disabled";
 			reg = <0x5a810100 0x100>;
-			interrupts = <0 81 4>;
+			interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_usb1>;
 			clocks = <&sys_clk 8>, <&mio_clk 7>, <&mio_clk 9>,
@@ -321,7 +328,7 @@
 			compatible = "socionext,uniphier-ehci", "generic-ehci";
 			status = "disabled";
 			reg = <0x5a820100 0x100>;
-			interrupts = <0 82 4>;
+			interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_usb2>;
 			clocks = <&sys_clk 8>, <&mio_clk 7>, <&mio_clk 10>,
@@ -362,14 +369,16 @@
 		timer@60000200 {
 			compatible = "arm,cortex-a9-global-timer";
 			reg = <0x60000200 0x20>;
-			interrupts = <1 11 0x104>;
+			interrupts = <GIC_PPI 11
+				(GIC_CPU_MASK_RAW(1) | IRQ_TYPE_LEVEL_HIGH)>;
 			clocks = <&arm_timer_clk>;
 		};
 
 		timer@60000600 {
 			compatible = "arm,cortex-a9-twd-timer";
 			reg = <0x60000600 0x20>;
-			interrupts = <1 13 0x104>;
+			interrupts = <GIC_PPI 13
+				(GIC_CPU_MASK_RAW(1) | IRQ_TYPE_LEVEL_HIGH)>;
 			clocks = <&arm_timer_clk>;
 		};
 
@@ -411,7 +420,7 @@
 			reg = <0x68000000 0x20>, <0x68100000 0x1000>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 65 4>;
+			interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_nand>;
 			clock-names = "nand", "nand_x", "ecc";
diff --git a/arch/arm/boot/dts/uniphier-support-card.dtsi b/arch/arm/boot/dts/uniphier-support-card.dtsi
index 444802fee9fb..97e7d5db8eb8 100644
--- a/arch/arm/boot/dts/uniphier-support-card.dtsi
+++ b/arch/arm/boot/dts/uniphier-support-card.dtsi
@@ -8,13 +8,13 @@
 &system_bus {
 	status = "okay";
 	ranges = <1 0x00000000 0x42000000 0x02000000>;
-	interrupt-parent = <&gpio>;
 
 	ethsc: ethernet@1,1f00000 {
 		compatible = "smsc,lan9118", "smsc,lan9115";
 		reg = <1 0x01f00000 0x1000>;
 		phy-mode = "mii";
 		reg-io-width = <4>;
+		interrupt-parent = <&gpio>;
 	};
 
 	serialsc: serial@1,1fb0000 {
@@ -22,5 +22,6 @@
 		reg = <1 0x01fb0000 0x20>;
 		clock-frequency = <12288000>;
 		reg-shift = <1>;
+		interrupt-parent = <&gpio>;
 	};
 };
diff --git a/arch/arm/boot/dts/usb_a9263.dts b/arch/arm/boot/dts/usb_a9263.dts
index 8a0cfbfd0c45..b6cb9cdf8197 100644
--- a/arch/arm/boot/dts/usb_a9263.dts
+++ b/arch/arm/boot/dts/usb_a9263.dts
@@ -60,7 +60,7 @@
 			spi0: spi@fffa4000 {
 				cs-gpios = <&pioB 15 GPIO_ACTIVE_HIGH>;
 				status = "okay";
-				mtd_dataflash@0 {
+				flash@0 {
 					compatible = "atmel,at45", "atmel,dataflash";
 					reg = <0>;
 					spi-max-frequency = <15000000>;
diff --git a/arch/arm/boot/dts/versatile-ab.dts b/arch/arm/boot/dts/versatile-ab.dts
index 79f7cc241282..a520615f4d8d 100644
--- a/arch/arm/boot/dts/versatile-ab.dts
+++ b/arch/arm/boot/dts/versatile-ab.dts
@@ -391,7 +391,7 @@
 			reg = <0x101f4000 0x1000>;
 			interrupts = <11>;
 			clocks = <&xtal24mhz>, <&pclk>;
-			clock-names = "SSPCLK", "apb_pclk";
+			clock-names = "sspclk", "apb_pclk";
 		};
 
 		fpga {
diff --git a/arch/arm/boot/dts/vf-colibri-eval-v3.dtsi b/arch/arm/boot/dts/vf-colibri-eval-v3.dtsi
index c12a1b8bc086..14c411f146f5 100644
--- a/arch/arm/boot/dts/vf-colibri-eval-v3.dtsi
+++ b/arch/arm/boot/dts/vf-colibri-eval-v3.dtsi
@@ -103,7 +103,7 @@
 	status = "okay";
 
 	/* M41T0M6 real time clock on carrier board */
-	rtc: m41t0m6@68 {
+	rtc: rtc@68 {
 		compatible = "st,m41t0";
 		reg = <0x68>;
 	};
diff --git a/arch/arm/boot/dts/vf610-bk4.dts b/arch/arm/boot/dts/vf610-bk4.dts
index 830c85476b3d..551a4c3ff4fa 100644
--- a/arch/arm/boot/dts/vf610-bk4.dts
+++ b/arch/arm/boot/dts/vf610-bk4.dts
@@ -61,7 +61,7 @@
 		regulator-max-microvolt = <3300000>;
 	};
 
-	spi-gpio {
+	spi {
 		compatible = "spi-gpio";
 		pinctrl-0 = <&pinctrl_gpio_spi>;
 		pinctrl-names = "default";
diff --git a/arch/arm/boot/dts/vf610-pinfunc.h b/arch/arm/boot/dts/vf610-pinfunc.h
index f1e5a7cf58a9..b7b7322a2d1b 100644
--- a/arch/arm/boot/dts/vf610-pinfunc.h
+++ b/arch/arm/boot/dts/vf610-pinfunc.h
@@ -420,7 +420,7 @@
 #define VF610_PAD_PTD29__FTM3_CH2		0x104 0x000 ALT4 0x0
 #define VF610_PAD_PTD29__DSPI2_SIN		0x104 0x000 ALT5 0x0
 #define VF610_PAD_PTD29__DEBUG_OUT11		0x104 0x000 ALT7 0x0
-#define VF610_PAD_PTD28__GPIO_66	 	0x108 0x000 ALT0 0x0
+#define VF610_PAD_PTD28__GPIO_66		0x108 0x000 ALT0 0x0
 #define VF610_PAD_PTD28__FB_AD28		0x108 0x000 ALT1 0x0
 #define VF610_PAD_PTD28__NF_IO12		0x108 0x000 ALT2 0x0
 #define VF610_PAD_PTD28__I2C2_SCL		0x108 0x34C ALT3 0x1
@@ -802,5 +802,55 @@
 #define VF610_PAD_PTE28__EWM_OUT		0x214 0x000 ALT7 0x0
 #define VF610_PAD_PTA7__GPIO_134		0x218 0x000 ALT0 0x0
 #define VF610_PAD_PTA7__VIU_PIX_CLK		0x218 0x3AC ALT1 0x1
+#define VF610_PAD_DDR_RESETB			0x21c 0x000 ALT0 0x0
+#define VF610_PAD_DDR_A15__DDR_A_15		0x220 0x000 ALT0 0x0
+#define VF610_PAD_DDR_A14__DDR_A_14		0x224 0x000 ALT0 0x0
+#define VF610_PAD_DDR_A13__DDR_A_13		0x228 0x000 ALT0 0x0
+#define VF610_PAD_DDR_A12__DDR_A_12		0x22c 0x000 ALT0 0x0
+#define VF610_PAD_DDR_A11__DDR_A_11		0x230 0x000 ALT0 0x0
+#define VF610_PAD_DDR_A10__DDR_A_10		0x234 0x000 ALT0 0x0
+#define VF610_PAD_DDR_A9__DDR_A_9		0x238 0x000 ALT0 0x0
+#define VF610_PAD_DDR_A8__DDR_A_8		0x23c 0x000 ALT0 0x0
+#define VF610_PAD_DDR_A7__DDR_A_7		0x240 0x000 ALT0 0x0
+#define VF610_PAD_DDR_A6__DDR_A_6		0x244 0x000 ALT0 0x0
+#define VF610_PAD_DDR_A5__DDR_A_5		0x248 0x000 ALT0 0x0
+#define VF610_PAD_DDR_A4__DDR_A_4		0x24c 0x000 ALT0 0x0
+#define VF610_PAD_DDR_A3__DDR_A_3		0x250 0x000 ALT0 0x0
+#define VF610_PAD_DDR_A2__DDR_A_2		0x254 0x000 ALT0 0x0
+#define VF610_PAD_DDR_A1__DDR_A_1		0x258 0x000 ALT0 0x0
+#define VF610_PAD_DDR_A0__DDR_A_0		0x25c 0x000 ALT0 0x0
+#define VF610_PAD_DDR_BA2__DDR_BA_2		0x260 0x000 ALT0 0x0
+#define VF610_PAD_DDR_BA1__DDR_BA_1		0x264 0x000 ALT0 0x0
+#define VF610_PAD_DDR_BA0__DDR_BA_0		0x268 0x000 ALT0 0x0
+#define VF610_PAD_DDR_CAS__DDR_CAS_B		0x26c 0x000 ALT0 0x0
+#define VF610_PAD_DDR_CKE__DDR_CKE_0		0x270 0x000 ALT0 0x0
+#define VF610_PAD_DDR_CLK__DDR_CLK_0		0x274 0x000 ALT0 0x0
+#define VF610_PAD_DDR_CS__DDR_CS_B_0		0x278 0x000 ALT0 0x0
+#define VF610_PAD_DDR_D15__DDR_D_15		0x27c 0x000 ALT0 0x0
+#define VF610_PAD_DDR_D14__DDR_D_14		0x280 0x000 ALT0 0x0
+#define VF610_PAD_DDR_D13__DDR_D_13		0x284 0x000 ALT0 0x0
+#define VF610_PAD_DDR_D12__DDR_D_12		0x288 0x000 ALT0 0x0
+#define VF610_PAD_DDR_D11__DDR_D_11		0x28c 0x000 ALT0 0x0
+#define VF610_PAD_DDR_D10__DDR_D_10		0x290 0x000 ALT0 0x0
+#define VF610_PAD_DDR_D9__DDR_D_9		0x294 0x000 ALT0 0x0
+#define VF610_PAD_DDR_D8__DDR_D_8		0x298 0x000 ALT0 0x0
+#define VF610_PAD_DDR_D7__DDR_D_7		0x29c 0x000 ALT0 0x0
+#define VF610_PAD_DDR_D6__DDR_D_6		0x2a0 0x000 ALT0 0x0
+#define VF610_PAD_DDR_D5__DDR_D_5		0x2a4 0x000 ALT0 0x0
+#define VF610_PAD_DDR_D4__DDR_D_4		0x2a8 0x000 ALT0 0x0
+#define VF610_PAD_DDR_D3__DDR_D_3		0x2ac 0x000 ALT0 0x0
+#define VF610_PAD_DDR_D2__DDR_D_2		0x2b0 0x000 ALT0 0x0
+#define VF610_PAD_DDR_D1__DDR_D_1		0x2b4 0x000 ALT0 0x0
+#define VF610_PAD_DDR_D0__DDR_D_0		0x2b8 0x000 ALT0 0x0
+#define VF610_PAD_DDR_DQM1__DDR_DQM_1		0x2bc 0x000 ALT0 0x0
+#define VF610_PAD_DDR_DQM0__DDR_DQM_0		0x2c0 0x000 ALT0 0x0
+#define VF610_PAD_DDR_DQS1__DDR_DQS_1		0x2c4 0x000 ALT0 0x0
+#define VF610_PAD_DDR_DQS0__DDR_DQS_0		0x2c8 0x000 ALT0 0x0
+#define VF610_PAD_DDR_RAS__DDR_RAS_B		0x2cc 0x000 ALT0 0x0
+#define VF610_PAD_DDR_WE__DDR_WE_B		0x2d0 0x000 ALT0 0x0
+#define VF610_PAD_DDR_ODT1__DDR_ODT_0		0x2d4 0x000 ALT0 0x0
+#define VF610_PAD_DDR_ODT0__DDR_ODT_1		0x2d8 0x000 ALT0 0x0
+#define VF610_PAD_DDR_DDRBYTE1__DDR_DDRBYTE1	0x2dc 0x000 ALT0 0x0
+#define VF610_PAD_DDR_DDRBYTE2__DDR_DDRBYTE2	0x2e0 0x000 ALT0 0x0
 
 #endif
diff --git a/arch/arm/boot/dts/vf610-twr.dts b/arch/arm/boot/dts/vf610-twr.dts
index dbb5ffcdcec4..6c246d5aa032 100644
--- a/arch/arm/boot/dts/vf610-twr.dts
+++ b/arch/arm/boot/dts/vf610-twr.dts
@@ -169,7 +169,7 @@
 	       VDDA-supply = <&reg_3p3v>;
 	       VDDIO-supply = <&reg_3p3v>;
 	       clocks = <&clks VF610_CLK_SAI2>;
-       };
+	};
 };
 
 &iomuxc {
diff --git a/arch/arm/boot/dts/vf610-zii-dev-rev-b.dts b/arch/arm/boot/dts/vf610-zii-dev-rev-b.dts
index 043ddd70372f..42ed4a04a12e 100644
--- a/arch/arm/boot/dts/vf610-zii-dev-rev-b.dts
+++ b/arch/arm/boot/dts/vf610-zii-dev-rev-b.dts
@@ -149,7 +149,7 @@
 						reg = <5>;
 						label = "dsa";
 						link = <&switch2port9>;
-						phy-mode = "rgmii-txid";
+						phy-mode = "1000base-x";
 
 						fixed-link {
 							speed = <1000>;
@@ -211,12 +211,14 @@
 						reg = <0>;
 						label = "lan6";
 						phy-handle = <&switch2phy0>;
+						phy-mode = "sgmii";
 					};
 
 					port@1 {
 						reg = <1>;
 						label = "lan7";
 						phy-handle = <&switch2phy1>;
+						phy-mode = "sgmii";
 					};
 
 					port@2 {
@@ -252,7 +254,7 @@
 					switch2port9: port@9 {
 						reg = <9>;
 						label = "dsa";
-						phy-mode = "rgmii-txid";
+						phy-mode = "1000base-x";
 						link = <&switch1port5
 							&switch0port5>;
 
@@ -286,7 +288,7 @@
 		};
 	};
 
-	spi0 {
+	spi-0 {
 		compatible = "spi-gpio";
 		pinctrl-0 = <&pinctrl_gpio_spi0>;
 		pinctrl-names = "default";
diff --git a/arch/arm/boot/dts/vf610.dtsi b/arch/arm/boot/dts/vf610.dtsi
index 956182d08e74..2fba923821d0 100644
--- a/arch/arm/boot/dts/vf610.dtsi
+++ b/arch/arm/boot/dts/vf610.dtsi
@@ -2,7 +2,6 @@
 //
 // Copyright 2013 Freescale Semiconductor, Inc.
 
-
 #include "vf500.dtsi"
 
 &a5_cpu {
diff --git a/arch/arm/boot/dts/zynq-7000.dtsi b/arch/arm/boot/dts/zynq-7000.dtsi
index 47c2a4b14c06..c193264a86ff 100644
--- a/arch/arm/boot/dts/zynq-7000.dtsi
+++ b/arch/arm/boot/dts/zynq-7000.dtsi
@@ -343,8 +343,6 @@
 			             <0 40 4>, <0 41 4>,
 			             <0 42 4>, <0 43 4>;
 			#dma-cells = <1>;
-			#dma-channels = <8>;
-			#dma-requests = <4>;
 			clocks = <&clkc 27>;
 			clock-names = "apb_pclk";
 		};
diff --git a/arch/arm/boot/dts/zynq-zc702.dts b/arch/arm/boot/dts/zynq-zc702.dts
index cf70aff26c66..d23201ba8cd7 100644
--- a/arch/arm/boot/dts/zynq-zc702.dts
+++ b/arch/arm/boot/dts/zynq-zc702.dts
@@ -30,14 +30,14 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 		autorepeat;
-		sw14 {
+		switch-14 {
 			label = "sw14";
 			gpios = <&gpio0 12 0>;
 			linux,code = <108>; /* down */
 			wakeup-source;
 			autorepeat;
 		};
-		sw13 {
+		switch-13 {
 			label = "sw13";
 			gpios = <&gpio0 14 0>;
 			linux,code = <103>; /* up */
diff --git a/arch/arm/boot/dts/zynq-zturn-common.dtsi b/arch/arm/boot/dts/zynq-zturn-common.dtsi
index bf5d1c4568b0..dfb1fbafe3aa 100644
--- a/arch/arm/boot/dts/zynq-zturn-common.dtsi
+++ b/arch/arm/boot/dts/zynq-zturn-common.dtsi
@@ -49,7 +49,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 		autorepeat;
-		K1 {
+		key {
 			label = "K1";
 			gpios = <&gpio0 0x32 0x1>;
 			linux,code = <0x66>;
diff --git a/arch/arm/boot/install.sh b/arch/arm/boot/install.sh
index 2a45092a40e3..9ec11fac7d8d 100644..100755
--- a/arch/arm/boot/install.sh
+++ b/arch/arm/boot/install.sh
@@ -1,7 +1,5 @@
 #!/bin/sh
 #
-# arch/arm/boot/install.sh
-#
 # This file is subject to the terms and conditions of the GNU General Public
 # License.  See the file "COPYING" in the main directory of this archive
 # for more details.
@@ -18,25 +16,6 @@
 #   $2 - kernel image file
 #   $3 - kernel map file
 #   $4 - default install path (blank if root directory)
-#
-
-verify () {
-	if [ ! -f "$1" ]; then
-		echo ""                                                   1>&2
-		echo " *** Missing file: $1"                              1>&2
-		echo ' *** You need to run "make" before "make install".' 1>&2
-		echo ""                                                   1>&2
-		exit 1
-	fi
-}
-
-# Make sure the files actually exist
-verify "$2"
-verify "$3"
-
-# User may have a custom install script
-if [ -x ~/bin/${INSTALLKERNEL} ]; then exec ~/bin/${INSTALLKERNEL} "$@"; fi
-if [ -x /sbin/${INSTALLKERNEL} ]; then exec /sbin/${INSTALLKERNEL} "$@"; fi
 
 if [ "$(basename $2)" = "zImage" ]; then
 # Compressed install
diff --git a/arch/arm/common/Kconfig b/arch/arm/common/Kconfig
index c8e198631d41..d2fdb1796f48 100644
--- a/arch/arm/common/Kconfig
+++ b/arch/arm/common/Kconfig
@@ -1,11 +1,7 @@
 # SPDX-License-Identifier: GPL-2.0
 config SA1111
 	bool
-	select DMABOUNCE if !ARCH_PXA
-
-config DMABOUNCE
-	bool
-	select ZONE_DMA
+	select ZONE_DMA if ARCH_SA1100
 
 config KRAIT_L2_ACCESSORS
 	bool
diff --git a/arch/arm/common/Makefile b/arch/arm/common/Makefile
index 8cd574be94cf..7bae8cbaafe7 100644
--- a/arch/arm/common/Makefile
+++ b/arch/arm/common/Makefile
@@ -6,7 +6,6 @@
 obj-y				+= firmware.o
 
 obj-$(CONFIG_SA1111)		+= sa1111.o
-obj-$(CONFIG_DMABOUNCE)		+= dmabounce.o
 obj-$(CONFIG_KRAIT_L2_ACCESSORS) += krait-l2-accessors.o
 obj-$(CONFIG_SHARP_LOCOMO)	+= locomo.o
 obj-$(CONFIG_SHARP_PARAM)	+= sharpsl_param.o
diff --git a/arch/arm/common/dmabounce.c b/arch/arm/common/dmabounce.c
deleted file mode 100644
index 7996c04393d5..000000000000
--- a/arch/arm/common/dmabounce.c
+++ /dev/null
@@ -1,582 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- *  arch/arm/common/dmabounce.c
- *
- *  Special dma_{map/unmap/dma_sync}_* routines for systems that have
- *  limited DMA windows. These functions utilize bounce buffers to
- *  copy data to/from buffers located outside the DMA region. This
- *  only works for systems in which DMA memory is at the bottom of
- *  RAM, the remainder of memory is at the top and the DMA memory
- *  can be marked as ZONE_DMA. Anything beyond that such as discontiguous
- *  DMA windows will require custom implementations that reserve memory
- *  areas at early bootup.
- *
- *  Original version by Brad Parker (brad@heeltoe.com)
- *  Re-written by Christopher Hoover <ch@murgatroid.com>
- *  Made generic by Deepak Saxena <dsaxena@plexity.net>
- *
- *  Copyright (C) 2002 Hewlett Packard Company.
- *  Copyright (C) 2004 MontaVista Software, Inc.
- */
-
-#include <linux/module.h>
-#include <linux/init.h>
-#include <linux/slab.h>
-#include <linux/page-flags.h>
-#include <linux/device.h>
-#include <linux/dma-direct.h>
-#include <linux/dma-map-ops.h>
-#include <linux/dmapool.h>
-#include <linux/list.h>
-#include <linux/scatterlist.h>
-
-#include <asm/cacheflush.h>
-#include <asm/dma-iommu.h>
-
-#undef STATS
-
-#ifdef STATS
-#define DO_STATS(X) do { X ; } while (0)
-#else
-#define DO_STATS(X) do { } while (0)
-#endif
-
-/* ************************************************** */
-
-struct safe_buffer {
-	struct list_head node;
-
-	/* original request */
-	void		*ptr;
-	size_t		size;
-	int		direction;
-
-	/* safe buffer info */
-	struct dmabounce_pool *pool;
-	void		*safe;
-	dma_addr_t	safe_dma_addr;
-};
-
-struct dmabounce_pool {
-	unsigned long	size;
-	struct dma_pool	*pool;
-#ifdef STATS
-	unsigned long	allocs;
-#endif
-};
-
-struct dmabounce_device_info {
-	struct device *dev;
-	struct list_head safe_buffers;
-#ifdef STATS
-	unsigned long total_allocs;
-	unsigned long map_op_count;
-	unsigned long bounce_count;
-	int attr_res;
-#endif
-	struct dmabounce_pool	small;
-	struct dmabounce_pool	large;
-
-	rwlock_t lock;
-
-	int (*needs_bounce)(struct device *, dma_addr_t, size_t);
-};
-
-#ifdef STATS
-static ssize_t dmabounce_show(struct device *dev, struct device_attribute *attr,
-			      char *buf)
-{
-	struct dmabounce_device_info *device_info = dev->archdata.dmabounce;
-	return sprintf(buf, "%lu %lu %lu %lu %lu %lu\n",
-		device_info->small.allocs,
-		device_info->large.allocs,
-		device_info->total_allocs - device_info->small.allocs -
-			device_info->large.allocs,
-		device_info->total_allocs,
-		device_info->map_op_count,
-		device_info->bounce_count);
-}
-
-static DEVICE_ATTR(dmabounce_stats, 0400, dmabounce_show, NULL);
-#endif
-
-
-/* allocate a 'safe' buffer and keep track of it */
-static inline struct safe_buffer *
-alloc_safe_buffer(struct dmabounce_device_info *device_info, void *ptr,
-		  size_t size, enum dma_data_direction dir)
-{
-	struct safe_buffer *buf;
-	struct dmabounce_pool *pool;
-	struct device *dev = device_info->dev;
-	unsigned long flags;
-
-	dev_dbg(dev, "%s(ptr=%p, size=%d, dir=%d)\n",
-		__func__, ptr, size, dir);
-
-	if (size <= device_info->small.size) {
-		pool = &device_info->small;
-	} else if (size <= device_info->large.size) {
-		pool = &device_info->large;
-	} else {
-		pool = NULL;
-	}
-
-	buf = kmalloc(sizeof(struct safe_buffer), GFP_ATOMIC);
-	if (buf == NULL) {
-		dev_warn(dev, "%s: kmalloc failed\n", __func__);
-		return NULL;
-	}
-
-	buf->ptr = ptr;
-	buf->size = size;
-	buf->direction = dir;
-	buf->pool = pool;
-
-	if (pool) {
-		buf->safe = dma_pool_alloc(pool->pool, GFP_ATOMIC,
-					   &buf->safe_dma_addr);
-	} else {
-		buf->safe = dma_alloc_coherent(dev, size, &buf->safe_dma_addr,
-					       GFP_ATOMIC);
-	}
-
-	if (buf->safe == NULL) {
-		dev_warn(dev,
-			 "%s: could not alloc dma memory (size=%d)\n",
-			 __func__, size);
-		kfree(buf);
-		return NULL;
-	}
-
-#ifdef STATS
-	if (pool)
-		pool->allocs++;
-	device_info->total_allocs++;
-#endif
-
-	write_lock_irqsave(&device_info->lock, flags);
-	list_add(&buf->node, &device_info->safe_buffers);
-	write_unlock_irqrestore(&device_info->lock, flags);
-
-	return buf;
-}
-
-/* determine if a buffer is from our "safe" pool */
-static inline struct safe_buffer *
-find_safe_buffer(struct dmabounce_device_info *device_info, dma_addr_t safe_dma_addr)
-{
-	struct safe_buffer *b, *rb = NULL;
-	unsigned long flags;
-
-	read_lock_irqsave(&device_info->lock, flags);
-
-	list_for_each_entry(b, &device_info->safe_buffers, node)
-		if (b->safe_dma_addr <= safe_dma_addr &&
-		    b->safe_dma_addr + b->size > safe_dma_addr) {
-			rb = b;
-			break;
-		}
-
-	read_unlock_irqrestore(&device_info->lock, flags);
-	return rb;
-}
-
-static inline void
-free_safe_buffer(struct dmabounce_device_info *device_info, struct safe_buffer *buf)
-{
-	unsigned long flags;
-
-	dev_dbg(device_info->dev, "%s(buf=%p)\n", __func__, buf);
-
-	write_lock_irqsave(&device_info->lock, flags);
-
-	list_del(&buf->node);
-
-	write_unlock_irqrestore(&device_info->lock, flags);
-
-	if (buf->pool)
-		dma_pool_free(buf->pool->pool, buf->safe, buf->safe_dma_addr);
-	else
-		dma_free_coherent(device_info->dev, buf->size, buf->safe,
-				    buf->safe_dma_addr);
-
-	kfree(buf);
-}
-
-/* ************************************************** */
-
-static struct safe_buffer *find_safe_buffer_dev(struct device *dev,
-		dma_addr_t dma_addr, const char *where)
-{
-	if (!dev || !dev->archdata.dmabounce)
-		return NULL;
-	if (dma_mapping_error(dev, dma_addr)) {
-		dev_err(dev, "Trying to %s invalid mapping\n", where);
-		return NULL;
-	}
-	return find_safe_buffer(dev->archdata.dmabounce, dma_addr);
-}
-
-static int needs_bounce(struct device *dev, dma_addr_t dma_addr, size_t size)
-{
-	if (!dev || !dev->archdata.dmabounce)
-		return 0;
-
-	if (dev->dma_mask) {
-		unsigned long limit, mask = *dev->dma_mask;
-
-		limit = (mask + 1) & ~mask;
-		if (limit && size > limit) {
-			dev_err(dev, "DMA mapping too big (requested %#x "
-				"mask %#Lx)\n", size, *dev->dma_mask);
-			return -E2BIG;
-		}
-
-		/* Figure out if we need to bounce from the DMA mask. */
-		if ((dma_addr | (dma_addr + size - 1)) & ~mask)
-			return 1;
-	}
-
-	return !!dev->archdata.dmabounce->needs_bounce(dev, dma_addr, size);
-}
-
-static inline dma_addr_t map_single(struct device *dev, void *ptr, size_t size,
-				    enum dma_data_direction dir,
-				    unsigned long attrs)
-{
-	struct dmabounce_device_info *device_info = dev->archdata.dmabounce;
-	struct safe_buffer *buf;
-
-	if (device_info)
-		DO_STATS ( device_info->map_op_count++ );
-
-	buf = alloc_safe_buffer(device_info, ptr, size, dir);
-	if (buf == NULL) {
-		dev_err(dev, "%s: unable to map unsafe buffer %p!\n",
-		       __func__, ptr);
-		return DMA_MAPPING_ERROR;
-	}
-
-	dev_dbg(dev, "%s: unsafe buffer %p (dma=%#x) mapped to %p (dma=%#x)\n",
-		__func__, buf->ptr, virt_to_dma(dev, buf->ptr),
-		buf->safe, buf->safe_dma_addr);
-
-	if ((dir == DMA_TO_DEVICE || dir == DMA_BIDIRECTIONAL) &&
-	    !(attrs & DMA_ATTR_SKIP_CPU_SYNC)) {
-		dev_dbg(dev, "%s: copy unsafe %p to safe %p, size %d\n",
-			__func__, ptr, buf->safe, size);
-		memcpy(buf->safe, ptr, size);
-	}
-
-	return buf->safe_dma_addr;
-}
-
-static inline void unmap_single(struct device *dev, struct safe_buffer *buf,
-				size_t size, enum dma_data_direction dir,
-				unsigned long attrs)
-{
-	BUG_ON(buf->size != size);
-	BUG_ON(buf->direction != dir);
-
-	dev_dbg(dev, "%s: unsafe buffer %p (dma=%#x) mapped to %p (dma=%#x)\n",
-		__func__, buf->ptr, virt_to_dma(dev, buf->ptr),
-		buf->safe, buf->safe_dma_addr);
-
-	DO_STATS(dev->archdata.dmabounce->bounce_count++);
-
-	if ((dir == DMA_FROM_DEVICE || dir == DMA_BIDIRECTIONAL) &&
-	    !(attrs & DMA_ATTR_SKIP_CPU_SYNC)) {
-		void *ptr = buf->ptr;
-
-		dev_dbg(dev, "%s: copy back safe %p to unsafe %p size %d\n",
-			__func__, buf->safe, ptr, size);
-		memcpy(ptr, buf->safe, size);
-
-		/*
-		 * Since we may have written to a page cache page,
-		 * we need to ensure that the data will be coherent
-		 * with user mappings.
-		 */
-		__cpuc_flush_dcache_area(ptr, size);
-	}
-	free_safe_buffer(dev->archdata.dmabounce, buf);
-}
-
-/* ************************************************** */
-
-/*
- * see if a buffer address is in an 'unsafe' range.  if it is
- * allocate a 'safe' buffer and copy the unsafe buffer into it.
- * substitute the safe buffer for the unsafe one.
- * (basically move the buffer from an unsafe area to a safe one)
- */
-static dma_addr_t dmabounce_map_page(struct device *dev, struct page *page,
-		unsigned long offset, size_t size, enum dma_data_direction dir,
-		unsigned long attrs)
-{
-	dma_addr_t dma_addr;
-	int ret;
-
-	dev_dbg(dev, "%s(page=%p,off=%#lx,size=%zx,dir=%x)\n",
-		__func__, page, offset, size, dir);
-
-	dma_addr = pfn_to_dma(dev, page_to_pfn(page)) + offset;
-
-	ret = needs_bounce(dev, dma_addr, size);
-	if (ret < 0)
-		return DMA_MAPPING_ERROR;
-
-	if (ret == 0) {
-		arm_dma_ops.sync_single_for_device(dev, dma_addr, size, dir);
-		return dma_addr;
-	}
-
-	if (PageHighMem(page)) {
-		dev_err(dev, "DMA buffer bouncing of HIGHMEM pages is not supported\n");
-		return DMA_MAPPING_ERROR;
-	}
-
-	return map_single(dev, page_address(page) + offset, size, dir, attrs);
-}
-
-/*
- * see if a mapped address was really a "safe" buffer and if so, copy
- * the data from the safe buffer back to the unsafe buffer and free up
- * the safe buffer.  (basically return things back to the way they
- * should be)
- */
-static void dmabounce_unmap_page(struct device *dev, dma_addr_t dma_addr, size_t size,
-		enum dma_data_direction dir, unsigned long attrs)
-{
-	struct safe_buffer *buf;
-
-	dev_dbg(dev, "%s(dma=%#x,size=%d,dir=%x)\n",
-		__func__, dma_addr, size, dir);
-
-	buf = find_safe_buffer_dev(dev, dma_addr, __func__);
-	if (!buf) {
-		arm_dma_ops.sync_single_for_cpu(dev, dma_addr, size, dir);
-		return;
-	}
-
-	unmap_single(dev, buf, size, dir, attrs);
-}
-
-static int __dmabounce_sync_for_cpu(struct device *dev, dma_addr_t addr,
-		size_t sz, enum dma_data_direction dir)
-{
-	struct safe_buffer *buf;
-	unsigned long off;
-
-	dev_dbg(dev, "%s(dma=%#x,sz=%zx,dir=%x)\n",
-		__func__, addr, sz, dir);
-
-	buf = find_safe_buffer_dev(dev, addr, __func__);
-	if (!buf)
-		return 1;
-
-	off = addr - buf->safe_dma_addr;
-
-	BUG_ON(buf->direction != dir);
-
-	dev_dbg(dev, "%s: unsafe buffer %p (dma=%#x off=%#lx) mapped to %p (dma=%#x)\n",
-		__func__, buf->ptr, virt_to_dma(dev, buf->ptr), off,
-		buf->safe, buf->safe_dma_addr);
-
-	DO_STATS(dev->archdata.dmabounce->bounce_count++);
-
-	if (dir == DMA_FROM_DEVICE || dir == DMA_BIDIRECTIONAL) {
-		dev_dbg(dev, "%s: copy back safe %p to unsafe %p size %d\n",
-			__func__, buf->safe + off, buf->ptr + off, sz);
-		memcpy(buf->ptr + off, buf->safe + off, sz);
-	}
-	return 0;
-}
-
-static void dmabounce_sync_for_cpu(struct device *dev,
-		dma_addr_t handle, size_t size, enum dma_data_direction dir)
-{
-	if (!__dmabounce_sync_for_cpu(dev, handle, size, dir))
-		return;
-
-	arm_dma_ops.sync_single_for_cpu(dev, handle, size, dir);
-}
-
-static int __dmabounce_sync_for_device(struct device *dev, dma_addr_t addr,
-		size_t sz, enum dma_data_direction dir)
-{
-	struct safe_buffer *buf;
-	unsigned long off;
-
-	dev_dbg(dev, "%s(dma=%#x,sz=%zx,dir=%x)\n",
-		__func__, addr, sz, dir);
-
-	buf = find_safe_buffer_dev(dev, addr, __func__);
-	if (!buf)
-		return 1;
-
-	off = addr - buf->safe_dma_addr;
-
-	BUG_ON(buf->direction != dir);
-
-	dev_dbg(dev, "%s: unsafe buffer %p (dma=%#x off=%#lx) mapped to %p (dma=%#x)\n",
-		__func__, buf->ptr, virt_to_dma(dev, buf->ptr), off,
-		buf->safe, buf->safe_dma_addr);
-
-	DO_STATS(dev->archdata.dmabounce->bounce_count++);
-
-	if (dir == DMA_TO_DEVICE || dir == DMA_BIDIRECTIONAL) {
-		dev_dbg(dev, "%s: copy out unsafe %p to safe %p, size %d\n",
-			__func__,buf->ptr + off, buf->safe + off, sz);
-		memcpy(buf->safe + off, buf->ptr + off, sz);
-	}
-	return 0;
-}
-
-static void dmabounce_sync_for_device(struct device *dev,
-		dma_addr_t handle, size_t size, enum dma_data_direction dir)
-{
-	if (!__dmabounce_sync_for_device(dev, handle, size, dir))
-		return;
-
-	arm_dma_ops.sync_single_for_device(dev, handle, size, dir);
-}
-
-static int dmabounce_dma_supported(struct device *dev, u64 dma_mask)
-{
-	if (dev->archdata.dmabounce)
-		return 0;
-
-	return arm_dma_ops.dma_supported(dev, dma_mask);
-}
-
-static const struct dma_map_ops dmabounce_ops = {
-	.alloc			= arm_dma_alloc,
-	.free			= arm_dma_free,
-	.mmap			= arm_dma_mmap,
-	.get_sgtable		= arm_dma_get_sgtable,
-	.map_page		= dmabounce_map_page,
-	.unmap_page		= dmabounce_unmap_page,
-	.sync_single_for_cpu	= dmabounce_sync_for_cpu,
-	.sync_single_for_device	= dmabounce_sync_for_device,
-	.map_sg			= arm_dma_map_sg,
-	.unmap_sg		= arm_dma_unmap_sg,
-	.sync_sg_for_cpu	= arm_dma_sync_sg_for_cpu,
-	.sync_sg_for_device	= arm_dma_sync_sg_for_device,
-	.dma_supported		= dmabounce_dma_supported,
-};
-
-static int dmabounce_init_pool(struct dmabounce_pool *pool, struct device *dev,
-		const char *name, unsigned long size)
-{
-	pool->size = size;
-	DO_STATS(pool->allocs = 0);
-	pool->pool = dma_pool_create(name, dev, size,
-				     0 /* byte alignment */,
-				     0 /* no page-crossing issues */);
-
-	return pool->pool ? 0 : -ENOMEM;
-}
-
-int dmabounce_register_dev(struct device *dev, unsigned long small_buffer_size,
-		unsigned long large_buffer_size,
-		int (*needs_bounce_fn)(struct device *, dma_addr_t, size_t))
-{
-	struct dmabounce_device_info *device_info;
-	int ret;
-
-	device_info = kmalloc(sizeof(struct dmabounce_device_info), GFP_ATOMIC);
-	if (!device_info) {
-		dev_err(dev,
-			"Could not allocated dmabounce_device_info\n");
-		return -ENOMEM;
-	}
-
-	ret = dmabounce_init_pool(&device_info->small, dev,
-				  "small_dmabounce_pool", small_buffer_size);
-	if (ret) {
-		dev_err(dev,
-			"dmabounce: could not allocate DMA pool for %ld byte objects\n",
-			small_buffer_size);
-		goto err_free;
-	}
-
-	if (large_buffer_size) {
-		ret = dmabounce_init_pool(&device_info->large, dev,
-					  "large_dmabounce_pool",
-					  large_buffer_size);
-		if (ret) {
-			dev_err(dev,
-				"dmabounce: could not allocate DMA pool for %ld byte objects\n",
-				large_buffer_size);
-			goto err_destroy;
-		}
-	}
-
-	device_info->dev = dev;
-	INIT_LIST_HEAD(&device_info->safe_buffers);
-	rwlock_init(&device_info->lock);
-	device_info->needs_bounce = needs_bounce_fn;
-
-#ifdef STATS
-	device_info->total_allocs = 0;
-	device_info->map_op_count = 0;
-	device_info->bounce_count = 0;
-	device_info->attr_res = device_create_file(dev, &dev_attr_dmabounce_stats);
-#endif
-
-	dev->archdata.dmabounce = device_info;
-	set_dma_ops(dev, &dmabounce_ops);
-
-	dev_info(dev, "dmabounce: registered device\n");
-
-	return 0;
-
- err_destroy:
-	dma_pool_destroy(device_info->small.pool);
- err_free:
-	kfree(device_info);
-	return ret;
-}
-EXPORT_SYMBOL(dmabounce_register_dev);
-
-void dmabounce_unregister_dev(struct device *dev)
-{
-	struct dmabounce_device_info *device_info = dev->archdata.dmabounce;
-
-	dev->archdata.dmabounce = NULL;
-	set_dma_ops(dev, NULL);
-
-	if (!device_info) {
-		dev_warn(dev,
-			 "Never registered with dmabounce but attempting"
-			 "to unregister!\n");
-		return;
-	}
-
-	if (!list_empty(&device_info->safe_buffers)) {
-		dev_err(dev,
-			"Removing from dmabounce with pending buffers!\n");
-		BUG();
-	}
-
-	if (device_info->small.pool)
-		dma_pool_destroy(device_info->small.pool);
-	if (device_info->large.pool)
-		dma_pool_destroy(device_info->large.pool);
-
-#ifdef STATS
-	if (device_info->attr_res == 0)
-		device_remove_file(dev, &dev_attr_dmabounce_stats);
-#endif
-
-	kfree(device_info);
-
-	dev_info(dev, "dmabounce: device unregistered\n");
-}
-EXPORT_SYMBOL(dmabounce_unregister_dev);
-
-MODULE_AUTHOR("Christopher Hoover <ch@hpl.hp.com>, Deepak Saxena <dsaxena@plexity.net>");
-MODULE_DESCRIPTION("Special dma_{map/unmap/dma_sync}_* routines for systems with limited DMA windows");
-MODULE_LICENSE("GPL");
diff --git a/arch/arm/common/locomo.c b/arch/arm/common/locomo.c
index 24d21ba63030..da30a4d4f35c 100644
--- a/arch/arm/common/locomo.c
+++ b/arch/arm/common/locomo.c
@@ -23,7 +23,6 @@
 #include <linux/spinlock.h>
 #include <linux/io.h>
 
-#include <mach/hardware.h>
 #include <asm/irq.h>
 #include <asm/mach/irq.h>
 
diff --git a/arch/arm/common/sa1111.c b/arch/arm/common/sa1111.c
index 5367f03beb46..f5e6990b8856 100644
--- a/arch/arm/common/sa1111.c
+++ b/arch/arm/common/sa1111.c
@@ -26,13 +26,16 @@
 #include <linux/clk.h>
 #include <linux/io.h>
 
-#include <mach/hardware.h>
 #include <asm/mach/irq.h>
 #include <asm/mach-types.h>
 #include <linux/sizes.h>
 
 #include <asm/hardware/sa1111.h>
 
+#ifdef CONFIG_ARCH_SA1100
+#include <mach/hardware.h>
+#endif
+
 /* SA1111 IRQs */
 #define IRQ_GPAIN0		(0)
 #define IRQ_GPAIN1		(1)
@@ -1386,70 +1389,9 @@ void sa1111_driver_unregister(struct sa1111_driver *driver)
 }
 EXPORT_SYMBOL(sa1111_driver_unregister);
 
-#ifdef CONFIG_DMABOUNCE
-/*
- * According to the "Intel StrongARM SA-1111 Microprocessor Companion
- * Chip Specification Update" (June 2000), erratum #7, there is a
- * significant bug in the SA1111 SDRAM shared memory controller.  If
- * an access to a region of memory above 1MB relative to the bank base,
- * it is important that address bit 10 _NOT_ be asserted. Depending
- * on the configuration of the RAM, bit 10 may correspond to one
- * of several different (processor-relative) address bits.
- *
- * This routine only identifies whether or not a given DMA address
- * is susceptible to the bug.
- *
- * This should only get called for sa1111_device types due to the
- * way we configure our device dma_masks.
- */
-static int sa1111_needs_bounce(struct device *dev, dma_addr_t addr, size_t size)
-{
-	/*
-	 * Section 4.6 of the "Intel StrongARM SA-1111 Development Module
-	 * User's Guide" mentions that jumpers R51 and R52 control the
-	 * target of SA-1111 DMA (either SDRAM bank 0 on Assabet, or
-	 * SDRAM bank 1 on Neponset). The default configuration selects
-	 * Assabet, so any address in bank 1 is necessarily invalid.
-	 */
-	return (machine_is_assabet() || machine_is_pfs168()) &&
-		(addr >= 0xc8000000 || (addr + size) >= 0xc8000000);
-}
-
-static int sa1111_notifier_call(struct notifier_block *n, unsigned long action,
-	void *data)
-{
-	struct sa1111_dev *dev = to_sa1111_device(data);
-
-	switch (action) {
-	case BUS_NOTIFY_ADD_DEVICE:
-		if (dev->dev.dma_mask && dev->dma_mask < 0xffffffffUL) {
-			int ret = dmabounce_register_dev(&dev->dev, 1024, 4096,
-					sa1111_needs_bounce);
-			if (ret)
-				dev_err(&dev->dev, "failed to register with dmabounce: %d\n", ret);
-		}
-		break;
-
-	case BUS_NOTIFY_DEL_DEVICE:
-		if (dev->dev.dma_mask && dev->dma_mask < 0xffffffffUL)
-			dmabounce_unregister_dev(&dev->dev);
-		break;
-	}
-	return NOTIFY_OK;
-}
-
-static struct notifier_block sa1111_bus_notifier = {
-	.notifier_call = sa1111_notifier_call,
-};
-#endif
-
 static int __init sa1111_init(void)
 {
 	int ret = bus_register(&sa1111_bus_type);
-#ifdef CONFIG_DMABOUNCE
-	if (ret == 0)
-		bus_register_notifier(&sa1111_bus_type, &sa1111_bus_notifier);
-#endif
 	if (ret == 0)
 		platform_driver_register(&sa1111_device_driver);
 	return ret;
@@ -1458,9 +1400,6 @@ static int __init sa1111_init(void)
 static void __exit sa1111_exit(void)
 {
 	platform_driver_unregister(&sa1111_device_driver);
-#ifdef CONFIG_DMABOUNCE
-	bus_unregister_notifier(&sa1111_bus_type, &sa1111_bus_notifier);
-#endif
 	bus_unregister(&sa1111_bus_type);
 }
 
diff --git a/arch/arm/configs/am200epdkit_defconfig b/arch/arm/configs/am200epdkit_defconfig
index 4e49d6cb2f62..3f633eaf9770 100644
--- a/arch/arm/configs/am200epdkit_defconfig
+++ b/arch/arm/configs/am200epdkit_defconfig
@@ -1,24 +1,22 @@
 CONFIG_LOCALVERSION="gum"
-# CONFIG_SWAP is not set
 CONFIG_SYSVIPC=y
 CONFIG_SYSFS_DEPRECATED_V2=y
+CONFIG_PREEMPT=y
 CONFIG_EXPERT=y
 # CONFIG_EPOLL is not set
 # CONFIG_SHMEM is not set
-# CONFIG_VM_EVENT_COUNTERS is not set
-CONFIG_SLAB=y
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
-# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_ARCH_MULTI_V7 is not set
 CONFIG_ARCH_PXA=y
 CONFIG_ARCH_GUMSTIX=y
-CONFIG_PCCARD=y
-CONFIG_PREEMPT=y
 CONFIG_AEABI=y
 # CONFIG_OABI_COMPAT is not set
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
 CONFIG_CMDLINE="console=ttyS0,115200n8 root=1f01 rootfstype=jffs2"
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_PARTITION_ADVANCED=y
+# CONFIG_SWAP is not set
+CONFIG_SLAB=y
+# CONFIG_VM_EVENT_COUNTERS is not set
 CONFIG_NET=y
 CONFIG_PACKET=m
 CONFIG_UNIX=y
@@ -34,6 +32,7 @@ CONFIG_BT_RFCOMM_TTY=y
 CONFIG_BT_BNEP=m
 CONFIG_BT_HCIUART=m
 CONFIG_BT_HCIUART_H4=y
+CONFIG_PCCARD=y
 CONFIG_MTD=y
 CONFIG_MTD_BLOCK=y
 CONFIG_MTD_CFI=y
@@ -47,14 +46,15 @@ CONFIG_MTD_COMPLEX_MAPPINGS=y
 CONFIG_MTD_PXA2XX=y
 CONFIG_BLK_DEV_LOOP=m
 CONFIG_BLK_DEV_SD=m
+# CONFIG_BLK_DEV_BSG is not set
 CONFIG_ATA=m
 CONFIG_PATA_PCMCIA=m
 CONFIG_NETDEVICES=y
 CONFIG_NET_ETHERNET=y
 CONFIG_SMC91X=m
+# CONFIG_LEGACY_PTYS is not set
 CONFIG_SERIAL_PXA=y
 CONFIG_SERIAL_PXA_CONSOLE=y
-# CONFIG_LEGACY_PTYS is not set
 # CONFIG_HW_RANDOM is not set
 # CONFIG_HWMON is not set
 CONFIG_WATCHDOG=y
@@ -83,16 +83,15 @@ CONFIG_VFAT_FS=y
 CONFIG_JFFS2_FS=y
 CONFIG_JFFS2_COMPRESSION_OPTIONS=y
 CONFIG_JFFS2_RUBIN=y
-CONFIG_PARTITION_ADVANCED=y
 CONFIG_NLS_CODEPAGE_437=y
 CONFIG_NLS_ISO8859_1=y
 CONFIG_DEBUG_KERNEL=y
 # CONFIG_DETECT_SOFTLOCKUP is not set
-# CONFIG_DEBUG_PREEMPT is not set
-# CONFIG_DEBUG_BUGVERBOSE is not set
-CONFIG_DEBUG_USER=y
 CONFIG_CRYPTO=y
 CONFIG_CRYPTO_CBC=m
 CONFIG_CRYPTO_ECB=m
 CONFIG_CRYPTO_PCBC=m
 CONFIG_CRYPTO_ARC4=m
+# CONFIG_DEBUG_BUGVERBOSE is not set
+# CONFIG_DEBUG_PREEMPT is not set
+CONFIG_DEBUG_USER=y
diff --git a/arch/arm/configs/aspeed_g4_defconfig b/arch/arm/configs/aspeed_g4_defconfig
index 5d20057bdc43..a5c65d28ca63 100644
--- a/arch/arm/configs/aspeed_g4_defconfig
+++ b/arch/arm/configs/aspeed_g4_defconfig
@@ -1,5 +1,4 @@
 CONFIG_KERNEL_XZ=y
-# CONFIG_SWAP is not set
 CONFIG_SYSVIPC=y
 CONFIG_NO_HZ_IDLE=y
 CONFIG_HIGH_RES_TIMERS=y
@@ -8,6 +7,7 @@ CONFIG_IKCONFIG=y
 CONFIG_IKCONFIG_PROC=y
 CONFIG_LOG_BUF_SHIFT=16
 CONFIG_CGROUPS=y
+CONFIG_NAMESPACES=y
 CONFIG_BLK_DEV_INITRD=y
 # CONFIG_RD_BZIP2 is not set
 # CONFIG_RD_LZO is not set
@@ -17,9 +17,6 @@ CONFIG_BLK_DEV_INITRD=y
 # CONFIG_AIO is not set
 CONFIG_EMBEDDED=y
 CONFIG_PERF_EVENTS=y
-# CONFIG_COMPAT_BRK is not set
-CONFIG_SLAB_FREELIST_RANDOM=y
-CONFIG_SLAB_FREELIST_HARDENED=y
 # CONFIG_ARCH_MULTI_V7 is not set
 CONFIG_ARCH_ASPEED=y
 CONFIG_MACH_ASPEED_G4=y
@@ -27,17 +24,17 @@ CONFIG_VMSPLIT_2G=y
 CONFIG_AEABI=y
 CONFIG_UACCESS_WITH_MEMCPY=y
 # CONFIG_ATAGS is not set
-CONFIG_ARM_APPENDED_DTB=y
-CONFIG_ARM_ATAG_DTB_COMPAT=y
 CONFIG_KEXEC=y
-CONFIG_FIRMWARE_MEMMAP=y
 CONFIG_JUMP_LABEL=y
 CONFIG_STRICT_KERNEL_RWX=y
-# CONFIG_BLK_DEV_BSG is not set
 # CONFIG_BLK_DEBUG_FS is not set
 # CONFIG_MQ_IOSCHED_DEADLINE is not set
 # CONFIG_MQ_IOSCHED_KYBER is not set
 # CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+# CONFIG_SWAP is not set
+CONFIG_SLAB_FREELIST_RANDOM=y
+CONFIG_SLAB_FREELIST_HARDENED=y
+# CONFIG_COMPAT_BRK is not set
 # CONFIG_COMPACTION is not set
 CONFIG_NET=y
 CONFIG_PACKET=y
@@ -48,7 +45,11 @@ CONFIG_INET=y
 CONFIG_IP_MULTICAST=y
 CONFIG_SYN_COOKIES=y
 # CONFIG_INET_DIAG is not set
+CONFIG_IPV6_ROUTER_PREF=y
+CONFIG_IPV6_ROUTE_INFO=y
+CONFIG_IPV6_OPTIMISTIC_DAD=y
 # CONFIG_IPV6_SIT is not set
+CONFIG_IPV6_MULTIPLE_TABLES=y
 CONFIG_NETFILTER=y
 # CONFIG_NETFILTER_ADVANCED is not set
 CONFIG_VLAN_8021Q=y
@@ -57,16 +58,17 @@ CONFIG_NET_NCSI=y
 CONFIG_DEVTMPFS=y
 CONFIG_DEVTMPFS_MOUNT=y
 # CONFIG_PREVENT_FIRMWARE_BUILD is not set
+CONFIG_FIRMWARE_MEMMAP=y
 CONFIG_MTD=y
 CONFIG_MTD_BLOCK=y
 CONFIG_MTD_PARTITIONED_MASTER=y
 CONFIG_MTD_SPI_NOR=y
 # CONFIG_MTD_SPI_NOR_USE_4K_SECTORS is not set
-CONFIG_SPI_ASPEED_SMC=y
 CONFIG_MTD_UBI=y
 CONFIG_MTD_UBI_FASTMAP=y
 CONFIG_MTD_UBI_BLOCK=y
 CONFIG_BLK_DEV_LOOP=y
+CONFIG_BLK_DEV_NBD=y
 CONFIG_EEPROM_AT24=y
 CONFIG_NETDEVICES=y
 CONFIG_NETCONSOLE=y
@@ -88,9 +90,9 @@ CONFIG_FTGMAC100=y
 # CONFIG_NET_VENDOR_MELLANOX is not set
 # CONFIG_NET_VENDOR_MICREL is not set
 # CONFIG_NET_VENDOR_MICROSEMI is not set
+# CONFIG_NET_VENDOR_NI is not set
 # CONFIG_NET_VENDOR_NATSEMI is not set
 # CONFIG_NET_VENDOR_NETRONOME is not set
-# CONFIG_NET_VENDOR_NI is not set
 # CONFIG_NET_VENDOR_QUALCOMM is not set
 # CONFIG_NET_VENDOR_RENESAS is not set
 # CONFIG_NET_VENDOR_ROCKER is not set
@@ -134,6 +136,7 @@ CONFIG_I2C_MUX_PCA954x=y
 CONFIG_I2C_ASPEED=y
 CONFIG_I2C_FSI=y
 CONFIG_SPI=y
+CONFIG_SPI_ASPEED_SMC=y
 CONFIG_GPIOLIB=y
 CONFIG_GPIO_SYSFS=y
 CONFIG_GPIO_ASPEED=y
@@ -145,6 +148,7 @@ CONFIG_SENSORS_ASPEED=y
 CONFIG_SENSORS_IIO_HWMON=y
 CONFIG_SENSORS_LM75=y
 CONFIG_SENSORS_NCT7904=y
+CONFIG_SENSORS_OCC_P8_I2C=y
 CONFIG_PMBUS=y
 CONFIG_SENSORS_ADM1275=y
 CONFIG_SENSORS_IBM_CFFPS=y
@@ -244,9 +248,8 @@ CONFIG_CRYPTO_USER_API_HASH=y
 # CONFIG_XZ_DEC_SPARC is not set
 CONFIG_PRINTK_TIME=y
 CONFIG_DYNAMIC_DEBUG=y
-CONFIG_DEBUG_INFO=y
-CONFIG_DEBUG_INFO_REDUCED=y
 CONFIG_DEBUG_INFO_DWARF4=y
+CONFIG_DEBUG_INFO_REDUCED=y
 CONFIG_GDB_SCRIPTS=y
 CONFIG_STRIP_ASM_SYMS=y
 CONFIG_DEBUG_FS=y
diff --git a/arch/arm/configs/aspeed_g5_defconfig b/arch/arm/configs/aspeed_g5_defconfig
index ae4f3c56ae6b..c7c11cbaa39d 100644
--- a/arch/arm/configs/aspeed_g5_defconfig
+++ b/arch/arm/configs/aspeed_g5_defconfig
@@ -1,5 +1,4 @@
 CONFIG_KERNEL_XZ=y
-# CONFIG_SWAP is not set
 CONFIG_SYSVIPC=y
 CONFIG_NO_HZ_IDLE=y
 CONFIG_HIGH_RES_TIMERS=y
@@ -8,6 +7,7 @@ CONFIG_IKCONFIG=y
 CONFIG_IKCONFIG_PROC=y
 CONFIG_LOG_BUF_SHIFT=16
 CONFIG_CGROUPS=y
+CONFIG_NAMESPACES=y
 CONFIG_BLK_DEV_INITRD=y
 # CONFIG_RD_BZIP2 is not set
 # CONFIG_RD_LZO is not set
@@ -17,9 +17,6 @@ CONFIG_BLK_DEV_INITRD=y
 # CONFIG_AIO is not set
 CONFIG_EMBEDDED=y
 CONFIG_PERF_EVENTS=y
-# CONFIG_COMPAT_BRK is not set
-CONFIG_SLAB_FREELIST_RANDOM=y
-CONFIG_SLAB_FREELIST_HARDENED=y
 CONFIG_ARCH_MULTI_V6=y
 CONFIG_ARCH_ASPEED=y
 CONFIG_MACH_ASPEED_G5=y
@@ -36,13 +33,15 @@ CONFIG_KEXEC=y
 CONFIG_VFP=y
 CONFIG_NEON=y
 CONFIG_KERNEL_MODE_NEON=y
-CONFIG_FIRMWARE_MEMMAP=y
 CONFIG_JUMP_LABEL=y
-# CONFIG_BLK_DEV_BSG is not set
 # CONFIG_BLK_DEBUG_FS is not set
 # CONFIG_MQ_IOSCHED_DEADLINE is not set
 # CONFIG_MQ_IOSCHED_KYBER is not set
 # CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+# CONFIG_SWAP is not set
+CONFIG_SLAB_FREELIST_RANDOM=y
+CONFIG_SLAB_FREELIST_HARDENED=y
+# CONFIG_COMPAT_BRK is not set
 # CONFIG_COMPACTION is not set
 CONFIG_NET=y
 CONFIG_PACKET=y
@@ -66,16 +65,17 @@ CONFIG_NETFILTER=y
 # CONFIG_NETFILTER_ADVANCED is not set
 CONFIG_VLAN_8021Q=y
 CONFIG_NET_NCSI=y
+CONFIG_MCTP=y
 # CONFIG_WIRELESS is not set
 CONFIG_DEVTMPFS=y
 CONFIG_DEVTMPFS_MOUNT=y
 # CONFIG_PREVENT_FIRMWARE_BUILD is not set
+CONFIG_FIRMWARE_MEMMAP=y
 CONFIG_MTD=y
 CONFIG_MTD_BLOCK=y
 CONFIG_MTD_PARTITIONED_MASTER=y
 CONFIG_MTD_SPI_NOR=y
 # CONFIG_MTD_SPI_NOR_USE_4K_SECTORS is not set
-CONFIG_SPI_ASPEED_SMC=y
 CONFIG_MTD_UBI=y
 CONFIG_MTD_UBI_FASTMAP=y
 CONFIG_MTD_UBI_BLOCK=y
@@ -83,6 +83,8 @@ CONFIG_BLK_DEV_LOOP=y
 CONFIG_BLK_DEV_NBD=y
 CONFIG_EEPROM_AT24=y
 CONFIG_EEPROM_AT25=y
+CONFIG_SCSI=y
+CONFIG_BLK_DEV_SD=y
 CONFIG_NETDEVICES=y
 CONFIG_NETCONSOLE=y
 # CONFIG_NET_VENDOR_ALACRITECH is not set
@@ -103,9 +105,9 @@ CONFIG_FTGMAC100=y
 # CONFIG_NET_VENDOR_MELLANOX is not set
 # CONFIG_NET_VENDOR_MICREL is not set
 # CONFIG_NET_VENDOR_MICROSEMI is not set
+# CONFIG_NET_VENDOR_NI is not set
 # CONFIG_NET_VENDOR_NATSEMI is not set
 # CONFIG_NET_VENDOR_NETRONOME is not set
-# CONFIG_NET_VENDOR_NI is not set
 # CONFIG_NET_VENDOR_QUALCOMM is not set
 # CONFIG_NET_VENDOR_RENESAS is not set
 # CONFIG_NET_VENDOR_ROCKER is not set
@@ -120,6 +122,8 @@ CONFIG_FTGMAC100=y
 # CONFIG_NET_VENDOR_WIZNET is not set
 CONFIG_BROADCOM_PHY=y
 CONFIG_REALTEK_PHY=y
+CONFIG_MCTP_SERIAL=y
+CONFIG_MCTP_TRANSPORT_I2C=y
 # CONFIG_USB_NET_DRIVERS is not set
 # CONFIG_WLAN is not set
 CONFIG_INPUT_EVDEV=y
@@ -147,6 +151,8 @@ CONFIG_IPMI_KCS_BMC_CDEV_IPMI=y
 CONFIG_IPMI_KCS_BMC_SERIO=y
 CONFIG_ASPEED_BT_IPMI_BMC=y
 CONFIG_HW_RANDOM_TIMERIOMEM=y
+CONFIG_TCG_TPM=y
+CONFIG_TCG_TIS_I2C=y
 # CONFIG_I2C_COMPAT is not set
 CONFIG_I2C_CHARDEV=y
 CONFIG_I2C_MUX_GPIO=y
@@ -156,6 +162,7 @@ CONFIG_I2C_ASPEED=y
 CONFIG_I2C_FSI=y
 CONFIG_I2C_SLAVE=y
 CONFIG_SPI=y
+CONFIG_SPI_ASPEED_SMC=y
 CONFIG_SPI_FSI=y
 CONFIG_GPIOLIB=y
 CONFIG_GPIO_SYSFS=y
@@ -180,6 +187,7 @@ CONFIG_SENSORS_IR38064=y
 CONFIG_SENSORS_ISL68137=y
 CONFIG_SENSORS_LM25066=y
 CONFIG_SENSORS_MAX31785=y
+CONFIG_SENSORS_MP5023=y
 CONFIG_SENSORS_UCD9000=y
 CONFIG_SENSORS_UCD9200=y
 CONFIG_SENSORS_SBTSI=y
@@ -200,6 +208,9 @@ CONFIG_USB_DYNAMIC_MINORS=y
 CONFIG_USB_EHCI_HCD=y
 CONFIG_USB_EHCI_ROOT_HUB_TT=y
 CONFIG_USB_EHCI_HCD_PLATFORM=y
+CONFIG_USB_STORAGE=y
+CONFIG_USB_SERIAL=y
+CONFIG_USB_SERIAL_PL2303=y
 CONFIG_USB_GADGET=y
 CONFIG_USB_ASPEED_VHUB=y
 CONFIG_USB_CONFIGFS=y
@@ -243,9 +254,13 @@ CONFIG_FSI_MASTER_ASPEED=y
 CONFIG_FSI_SCOM=y
 CONFIG_FSI_SBEFIFO=y
 CONFIG_FSI_OCC=y
+CONFIG_PECI=y
+CONFIG_PECI_CPU=y
+CONFIG_PECI_ASPEED=y
 CONFIG_EXT4_FS=y
 CONFIG_FANOTIFY=y
 CONFIG_OVERLAY_FS=y
+CONFIG_VFAT_FS=y
 CONFIG_TMPFS=y
 CONFIG_JFFS2_FS=y
 # CONFIG_JFFS2_FS_WRITEBUFFER is not set
@@ -261,6 +276,9 @@ CONFIG_PSTORE_PMSG=y
 CONFIG_PSTORE_FTRACE=y
 CONFIG_PSTORE_RAM=y
 # CONFIG_NETWORK_FILESYSTEMS is not set
+CONFIG_NLS_CODEPAGE_437=y
+CONFIG_NLS_ISO8859_1=y
+# CONFIG_SECURITYFS is not set
 CONFIG_HARDENED_USERCOPY=y
 CONFIG_FORTIFY_SOURCE=y
 CONFIG_CRYPTO_HMAC=y
@@ -273,9 +291,8 @@ CONFIG_CRYPTO_USER_API_HASH=y
 # CONFIG_XZ_DEC_SPARC is not set
 CONFIG_PRINTK_TIME=y
 CONFIG_DYNAMIC_DEBUG=y
-CONFIG_DEBUG_INFO=y
-CONFIG_DEBUG_INFO_REDUCED=y
 CONFIG_DEBUG_INFO_DWARF4=y
+CONFIG_DEBUG_INFO_REDUCED=y
 CONFIG_GDB_SCRIPTS=y
 CONFIG_STRIP_ASM_SYMS=y
 CONFIG_DEBUG_FS=y
diff --git a/arch/arm/configs/assabet_defconfig b/arch/arm/configs/assabet_defconfig
index 04c86ff558da..8ba8eb7a4adf 100644
--- a/arch/arm/configs/assabet_defconfig
+++ b/arch/arm/configs/assabet_defconfig
@@ -1,25 +1,21 @@
 CONFIG_SYSVIPC=y
 CONFIG_LOG_BUF_SHIFT=14
 CONFIG_BLK_DEV_INITRD=y
-CONFIG_MODULES=y
+CONFIG_ARCH_MULTI_V4=y
+# CONFIG_ARCH_MULTI_V7 is not set
 CONFIG_ARCH_SA1100=y
 CONFIG_SA1100_ASSABET=y
-CONFIG_PCCARD=y
-CONFIG_PCMCIA_SA1100=y
-CONFIG_LEDS=y
-CONFIG_LEDS_CPU=y
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
 CONFIG_CMDLINE="mem=32M console=ttySA0,38400n8 initrd=0xc0800000,3M root=/dev/ram"
 CONFIG_FPE_NWFPE=y
 CONFIG_PM=y
+CONFIG_MODULES=y
+CONFIG_PARTITION_ADVANCED=y
 CONFIG_NET=y
 CONFIG_UNIX=y
 CONFIG_INET=y
 # CONFIG_IPV6 is not set
-CONFIG_IRDA=m
-CONFIG_IRLAN=m
-CONFIG_SA1100_FIR=m
+CONFIG_PCCARD=y
+CONFIG_PCMCIA_SA1100=y
 CONFIG_MTD=y
 CONFIG_MTD_REDBOOT_PARTS=y
 CONFIG_MTD_BLOCK=y
@@ -46,11 +42,14 @@ CONFIG_FB=y
 CONFIG_FB_SA1100=y
 # CONFIG_VGA_CONSOLE is not set
 CONFIG_SOUND=y
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=y
+CONFIG_LEDS_TRIGGERS=y
+CONFIG_LEDS_TRIGGER_CPU=y
 CONFIG_EXT2_FS=y
 CONFIG_MSDOS_FS=y
 CONFIG_TMPFS=y
 CONFIG_JFFS2_FS=y
 CONFIG_NFS_FS=y
-CONFIG_PARTITION_ADVANCED=y
 CONFIG_NLS_CODEPAGE_437=y
 CONFIG_DEBUG_USER=y
diff --git a/arch/arm/configs/at91_dt_defconfig b/arch/arm/configs/at91_dt_defconfig
index a6310c8abcc3..9ea08337b174 100644
--- a/arch/arm/configs/at91_dt_defconfig
+++ b/arch/arm/configs/at91_dt_defconfig
@@ -1,14 +1,13 @@
 # CONFIG_LOCALVERSION_AUTO is not set
-# CONFIG_SWAP is not set
 CONFIG_SYSVIPC=y
 CONFIG_NO_HZ_IDLE=y
 CONFIG_HIGH_RES_TIMERS=y
 CONFIG_LOG_BUF_SHIFT=14
+CONFIG_CGROUPS=y
 CONFIG_BLK_DEV_INITRD=y
 CONFIG_CC_OPTIMIZE_FOR_SIZE=y
 CONFIG_KALLSYMS_ALL=y
 CONFIG_EMBEDDED=y
-CONFIG_SLAB=y
 CONFIG_ARCH_MULTI_V4T=y
 CONFIG_ARCH_MULTI_V5=y
 # CONFIG_ARCH_MULTI_V7 is not set
@@ -26,8 +25,9 @@ CONFIG_CMDLINE="console=ttyS0,115200 initrd=0x21100000,25165824 root=/dev/ram0 r
 CONFIG_KEXEC=y
 CONFIG_MODULES=y
 CONFIG_MODULE_UNLOAD=y
-# CONFIG_BLK_DEV_BSG is not set
 # CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+# CONFIG_SWAP is not set
+CONFIG_SLAB=y
 CONFIG_NET=y
 CONFIG_PACKET=y
 CONFIG_UNIX=y
@@ -40,7 +40,6 @@ CONFIG_IP_PNP_RARP=y
 # CONFIG_INET_DIAG is not set
 CONFIG_IPV6_SIT_6RD=y
 CONFIG_CAN=y
-CONFIG_CAN_AT91=y
 CONFIG_CFG80211=y
 CONFIG_MAC80211=y
 CONFIG_DEVTMPFS=y
@@ -50,13 +49,13 @@ CONFIG_DEVTMPFS_MOUNT=y
 CONFIG_MTD=y
 CONFIG_MTD_TESTS=m
 CONFIG_MTD_CMDLINE_PARTS=y
-CONFIG_MTD_BLOCK=y
 CONFIG_MTD_DATAFLASH=y
 CONFIG_MTD_RAW_NAND=y
 CONFIG_MTD_NAND_ATMEL=y
 CONFIG_MTD_SPI_NOR=y
 CONFIG_MTD_UBI=y
 CONFIG_MTD_UBI_FASTMAP=y
+CONFIG_MTD_UBI_BLOCK=y
 CONFIG_BLK_DEV_LOOP=y
 CONFIG_BLK_DEV_RAM=y
 CONFIG_BLK_DEV_RAM_COUNT=4
@@ -65,6 +64,7 @@ CONFIG_ATMEL_SSC=y
 CONFIG_EEPROM_AT24=m
 CONFIG_SCSI=y
 CONFIG_BLK_DEV_SD=y
+# CONFIG_BLK_DEV_BSG is not set
 # CONFIG_SCSI_LOWLEVEL is not set
 CONFIG_NETDEVICES=y
 # CONFIG_NET_VENDOR_BROADCOM is not set
@@ -80,6 +80,7 @@ CONFIG_DM9000=y
 # CONFIG_NET_VENDOR_STMICRO is not set
 CONFIG_DAVICOM_PHY=y
 CONFIG_MICREL_PHY=y
+CONFIG_CAN_AT91=y
 CONFIG_LIBERTAS=m
 CONFIG_LIBERTAS_SDIO=m
 CONFIG_LIBERTAS_SPI=m
@@ -138,9 +139,9 @@ CONFIG_MEDIA_USB_SUPPORT=y
 CONFIG_USB_VIDEO_CLASS=m
 CONFIG_V4L_PLATFORM_DRIVERS=y
 CONFIG_VIDEO_ATMEL_ISI=y
+CONFIG_VIDEO_MT9V032=m
 CONFIG_VIDEO_OV2640=m
 CONFIG_VIDEO_OV7740=m
-CONFIG_VIDEO_MT9V032=m
 CONFIG_DRM=y
 CONFIG_DRM_ATMEL_HLCDC=y
 CONFIG_DRM_PANEL_SIMPLE=y
@@ -195,7 +196,6 @@ CONFIG_RTC_DRV_AT91SAM9=y
 CONFIG_DMADEVICES=y
 CONFIG_AT_HDMAC=y
 CONFIG_AT_XDMAC=y
-CONFIG_MICROCHIP_PIT64B=y
 # CONFIG_IOMMU_SUPPORT is not set
 CONFIG_IIO=y
 CONFIG_AT91_ADC=y
@@ -206,6 +206,7 @@ CONFIG_PWM_ATMEL_HLCDC_PWM=y
 CONFIG_PWM_ATMEL_TCB=y
 CONFIG_EXT4_FS=y
 CONFIG_FANOTIFY=y
+CONFIG_AUTOFS_FS=m
 CONFIG_VFAT_FS=y
 CONFIG_TMPFS=y
 CONFIG_UBIFS_FS=y
@@ -216,7 +217,14 @@ CONFIG_NLS_CODEPAGE_437=y
 CONFIG_NLS_CODEPAGE_850=y
 CONFIG_NLS_ISO8859_1=y
 CONFIG_NLS_UTF8=y
-CONFIG_CRYPTO_ECB=y
+CONFIG_CRYPTO_CBC=y
+CONFIG_CRYPTO_CFB=y
+CONFIG_CRYPTO_OFB=y
+CONFIG_CRYPTO_XTS=y
+CONFIG_CRYPTO_HMAC=y
+CONFIG_CRYPTO_SHA1=y
+CONFIG_CRYPTO_SHA512=y
+CONFIG_CRYPTO_DES=y
 CONFIG_CRYPTO_USER_API_HASH=m
 CONFIG_CRYPTO_USER_API_SKCIPHER=m
 CONFIG_CRYPTO_DEV_ATMEL_AES=y
diff --git a/arch/arm/configs/axm55xx_defconfig b/arch/arm/configs/axm55xx_defconfig
index 46075216ee6d..bfbaa2df3be5 100644
--- a/arch/arm/configs/axm55xx_defconfig
+++ b/arch/arm/configs/axm55xx_defconfig
@@ -3,6 +3,7 @@ CONFIG_POSIX_MQUEUE=y
 CONFIG_FHANDLE=y
 CONFIG_AUDIT=y
 CONFIG_HIGH_RES_TIMERS=y
+CONFIG_PREEMPT=y
 CONFIG_BSD_PROCESS_ACCT=y
 CONFIG_BSD_PROCESS_ACCT_V3=y
 CONFIG_TASKSTATS=y
@@ -21,12 +22,8 @@ CONFIG_SCHED_AUTOGROUP=y
 CONFIG_RELAY=y
 CONFIG_BLK_DEV_INITRD=y
 CONFIG_EMBEDDED=y
-# CONFIG_COMPAT_BRK is not set
 CONFIG_PROFILING=y
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
 CONFIG_ARCH_AXXIA=y
-CONFIG_GPIO_PCA953X=y
 CONFIG_ARM_LPAE=y
 CONFIG_ARM_THUMBEE=y
 CONFIG_ARM_ERRATA_430973=y
@@ -37,26 +34,24 @@ CONFIG_ARM_ERRATA_754327=y
 CONFIG_ARM_ERRATA_764369=y
 CONFIG_ARM_ERRATA_775420=y
 CONFIG_ARM_ERRATA_798181=y
-CONFIG_PCI=y
-CONFIG_PCI_MSI=y
 CONFIG_PCIE_AXXIA=y
 CONFIG_SMP=y
 CONFIG_NR_CPUS=16
 CONFIG_HOTPLUG_CPU=y
-CONFIG_PREEMPT=y
 CONFIG_AEABI=y
 CONFIG_OABI_COMPAT=y
 CONFIG_HIGHMEM=y
-CONFIG_KSM=y
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
 CONFIG_ARM_APPENDED_DTB=y
 CONFIG_ARM_ATAG_DTB_COMPAT=y
 CONFIG_VFP=y
 CONFIG_NEON=y
+# CONFIG_SUSPEND is not set
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
 # CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
 CONFIG_BINFMT_MISC=y
-# CONFIG_SUSPEND is not set
+# CONFIG_COMPAT_BRK is not set
+CONFIG_KSM=y
 CONFIG_NET=y
 CONFIG_PACKET=y
 CONFIG_UNIX=y
@@ -76,6 +71,8 @@ CONFIG_INET_IPCOMP=y
 CONFIG_NETWORK_PHY_TIMESTAMPING=y
 CONFIG_BRIDGE=y
 # CONFIG_WIRELESS is not set
+CONFIG_PCI=y
+CONFIG_PCI_MSI=y
 CONFIG_DEVTMPFS=y
 CONFIG_DEVTMPFS_MOUNT=y
 CONFIG_MTD=y
@@ -142,9 +139,10 @@ CONFIG_DP83640_PHY=y
 CONFIG_GPIOLIB=y
 CONFIG_GPIO_SYSFS=y
 CONFIG_GPIO_PL061=y
-CONFIG_POWER_SUPPLY=y
+CONFIG_GPIO_PCA953X=y
 CONFIG_POWER_RESET=y
 CONFIG_POWER_RESET_AXXIA=y
+CONFIG_POWER_SUPPLY=y
 CONFIG_SENSORS_ADT7475=y
 CONFIG_SENSORS_JC42=y
 CONFIG_SENSORS_LM75=y
@@ -224,8 +222,9 @@ CONFIG_NFS_FSCACHE=y
 CONFIG_SUNRPC_DEBUG=y
 CONFIG_NLS_CODEPAGE_437=y
 CONFIG_NLS_ISO8859_1=y
+CONFIG_CRYPTO_XCBC=y
 CONFIG_PRINTK_TIME=y
-CONFIG_DEBUG_INFO=y
+CONFIG_DEBUG_INFO_DWARF_TOOLCHAIN_DEFAULT=y
 CONFIG_DEBUG_FS=y
 CONFIG_MAGIC_SYSRQ=y
 # CONFIG_SCHED_DEBUG is not set
@@ -233,6 +232,5 @@ CONFIG_RCU_CPU_STALL_TIMEOUT=60
 # CONFIG_FTRACE is not set
 CONFIG_DEBUG_USER=y
 CONFIG_CRYPTO_GCM=y
-CONFIG_CRYPTO_XCBC=y
 CONFIG_CRYPTO_SHA256=y
 # CONFIG_CRYPTO_ANSI_CPRNG is not set
diff --git a/arch/arm/configs/badge4_defconfig b/arch/arm/configs/badge4_defconfig
index d9119da65f48..337e5c9718ae 100644
--- a/arch/arm/configs/badge4_defconfig
+++ b/arch/arm/configs/badge4_defconfig
@@ -1,26 +1,22 @@
 CONFIG_LOG_BUF_SHIFT=14
 CONFIG_EXPERT=y
-CONFIG_MODULES=y
-CONFIG_MODVERSIONS=y
+CONFIG_ARCH_MULTI_V4=y
+# CONFIG_ARCH_MULTI_V7 is not set
 CONFIG_ARCH_SA1100=y
 CONFIG_SA1100_BADGE4=y
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_UNUSED_BOARD_FILES=y
 CONFIG_CMDLINE="init=/linuxrc root=/dev/mtdblock3"
 CONFIG_CPU_FREQ_GOV_PERFORMANCE=y
 CONFIG_FPE_NWFPE=y
-CONFIG_BINFMT_AOUT=m
+CONFIG_MODULES=y
+CONFIG_MODVERSIONS=y
+CONFIG_PARTITION_ADVANCED=y
 CONFIG_BINFMT_MISC=m
 CONFIG_NET=y
 CONFIG_PACKET=y
 CONFIG_UNIX=y
 CONFIG_INET=y
 # CONFIG_IPV6 is not set
-CONFIG_IRDA=y
-CONFIG_IRLAN=y
-CONFIG_IRCOMM=y
-CONFIG_IRDA_ULTRA=y
-CONFIG_SA1100_FIR=y
 CONFIG_BT=m
 CONFIG_BT_HCIUART=m
 CONFIG_BT_HCIVHCI=m
@@ -101,10 +97,9 @@ CONFIG_MINIX_FS=m
 CONFIG_NFS_FS=m
 CONFIG_NFS_V3=y
 CONFIG_SMB_FS=m
-CONFIG_PARTITION_ADVANCED=y
-CONFIG_MAGIC_SYSRQ=y
 CONFIG_DEBUG_KERNEL=y
 # CONFIG_DEBUG_BUGVERBOSE is not set
-CONFIG_DEBUG_INFO=y
+CONFIG_DEBUG_INFO_DWARF_TOOLCHAIN_DEFAULT=y
+CONFIG_MAGIC_SYSRQ=y
 CONFIG_DEBUG_USER=y
 CONFIG_DEBUG_LL=y
diff --git a/arch/arm/configs/bcm2835_defconfig b/arch/arm/configs/bcm2835_defconfig
index 383c632eba7b..a51babd178c2 100644
--- a/arch/arm/configs/bcm2835_defconfig
+++ b/arch/arm/configs/bcm2835_defconfig
@@ -1,7 +1,8 @@
 # CONFIG_LOCALVERSION_AUTO is not set
 CONFIG_SYSVIPC=y
-CONFIG_NO_HZ=y
+CONFIG_NO_HZ_IDLE=y
 CONFIG_HIGH_RES_TIMERS=y
+CONFIG_PREEMPT_VOLUNTARY=y
 CONFIG_BSD_PROCESS_ACCT=y
 CONFIG_BSD_PROCESS_ACCT_V3=y
 CONFIG_LOG_BUF_SHIFT=18
@@ -19,20 +20,12 @@ CONFIG_BLK_DEV_INITRD=y
 CONFIG_CC_OPTIMIZE_FOR_SIZE=y
 CONFIG_KALLSYMS_ALL=y
 CONFIG_EMBEDDED=y
-# CONFIG_COMPAT_BRK is not set
 CONFIG_PROFILING=y
-CONFIG_JUMP_LABEL=y
 CONFIG_CC_STACKPROTECTOR_REGULAR=y
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
 CONFIG_ARCH_MULTI_V6=y
 CONFIG_ARCH_BCM=y
 CONFIG_ARCH_BCM2835=y
-CONFIG_PREEMPT_VOLUNTARY=y
 CONFIG_AEABI=y
-CONFIG_KSM=y
-CONFIG_CLEANCACHE=y
-CONFIG_CMA=y
 CONFIG_SECCOMP=y
 CONFIG_KEXEC=y
 CONFIG_CRASH_DUMP=y
@@ -45,9 +38,15 @@ CONFIG_CPU_FREQ_GOV_ONDEMAND=y
 CONFIG_CPUFREQ_DT=y
 CONFIG_ARM_RASPBERRYPI_CPUFREQ=y
 CONFIG_VFP=y
-# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
 # CONFIG_SUSPEND is not set
 CONFIG_PM=y
+CONFIG_JUMP_LABEL=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+# CONFIG_COMPAT_BRK is not set
+CONFIG_KSM=y
+CONFIG_CMA=y
 CONFIG_NET=y
 CONFIG_PACKET=y
 CONFIG_UNIX=y
@@ -64,8 +63,7 @@ CONFIG_MAC80211=y
 CONFIG_DEVTMPFS=y
 CONFIG_DEVTMPFS_MOUNT=y
 # CONFIG_STANDALONE is not set
-CONFIG_DMA_CMA=y
-CONFIG_CMA_SIZE_MBYTES=32
+CONFIG_RASPBERRYPI_FIRMWARE=y
 CONFIG_SCSI=y
 CONFIG_BLK_DEV_SD=y
 CONFIG_SCSI_CONSTANTS=y
@@ -107,6 +105,7 @@ CONFIG_REGULATOR_GPIO=y
 CONFIG_MEDIA_SUPPORT=y
 CONFIG_MEDIA_CAMERA_SUPPORT=y
 CONFIG_DRM=y
+CONFIG_DRM_V3D=y
 CONFIG_DRM_VC4=y
 CONFIG_FB_SIMPLE=y
 CONFIG_FRAMEBUFFER_CONSOLE=y
@@ -152,7 +151,6 @@ CONFIG_BCM2835_MBOX=y
 CONFIG_RASPBERRYPI_POWER=y
 CONFIG_PWM=y
 CONFIG_PWM_BCM2835=y
-CONFIG_RASPBERRYPI_FIRMWARE=y
 CONFIG_EXT2_FS=y
 CONFIG_EXT2_FS_XATTR=y
 CONFIG_EXT2_FS_POSIX_ACL=y
@@ -171,20 +169,22 @@ CONFIG_NLS_CODEPAGE_437=y
 CONFIG_NLS_ASCII=y
 CONFIG_NLS_ISO8859_1=y
 CONFIG_NLS_UTF8=y
+# CONFIG_XZ_DEC_ARM is not set
+# CONFIG_XZ_DEC_ARMTHUMB is not set
+CONFIG_DMA_CMA=y
+CONFIG_CMA_SIZE_MBYTES=32
 CONFIG_PRINTK_TIME=y
 CONFIG_BOOT_PRINTK_DELAY=y
 CONFIG_DYNAMIC_DEBUG=y
-CONFIG_DEBUG_INFO=y
+CONFIG_DEBUG_INFO_DWARF_TOOLCHAIN_DEFAULT=y
 # CONFIG_ENABLE_MUST_CHECK is not set
-CONFIG_DEBUG_MEMORY_INIT=y
 CONFIG_LOCKUP_DETECTOR=y
-CONFIG_SCHED_TRACER=y
-CONFIG_STACK_TRACER=y
-CONFIG_FUNCTION_PROFILER=y
-CONFIG_TEST_KSTRTOX=y
 CONFIG_DEBUG_FS=y
 CONFIG_KGDB=y
 CONFIG_KGDB_KDB=y
+CONFIG_DEBUG_MEMORY_INIT=y
+CONFIG_FUNCTION_PROFILER=y
+CONFIG_STACK_TRACER=y
+CONFIG_SCHED_TRACER=y
 CONFIG_STRICT_DEVMEM=y
-# CONFIG_XZ_DEC_ARM is not set
-# CONFIG_XZ_DEC_ARMTHUMB is not set
+CONFIG_TEST_KSTRTOX=y
diff --git a/arch/arm/configs/cerfcube_defconfig b/arch/arm/configs/cerfcube_defconfig
index 3f910bbf1bfd..9ada868e2648 100644
--- a/arch/arm/configs/cerfcube_defconfig
+++ b/arch/arm/configs/cerfcube_defconfig
@@ -1,23 +1,21 @@
 CONFIG_SYSVIPC=y
 CONFIG_BSD_PROCESS_ACCT=y
 CONFIG_LOG_BUF_SHIFT=14
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
-CONFIG_MODULE_FORCE_UNLOAD=y
+CONFIG_ARCH_MULTI_V4=y
+# CONFIG_ARCH_MULTI_V7 is not set
 CONFIG_ARCH_SA1100=y
 CONFIG_SA1100_CERF=y
 CONFIG_SA1100_CERF_FLASH_16MB=y
-CONFIG_PCCARD=m
-CONFIG_PCMCIA_SA1100=m
-CONFIG_LEDS=y
-CONFIG_LEDS_CPU=y
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_UNUSED_BOARD_FILES=y
 CONFIG_CMDLINE="console=ttySA0,38400 root=/dev/mtdblock3 rootfstype=jffs2 rw mem=32M init=/linuxrc"
 CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE=y
 CONFIG_CPU_FREQ_GOV_USERSPACE=m
 CONFIG_FPE_FASTFPE=y
 CONFIG_PM=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_MODULE_FORCE_UNLOAD=y
+CONFIG_PARTITION_ADVANCED=y
 CONFIG_NET=y
 CONFIG_PACKET=y
 CONFIG_UNIX=y
@@ -27,9 +25,11 @@ CONFIG_IP_PNP_DHCP=y
 CONFIG_IP_PNP_BOOTP=y
 CONFIG_IP_PNP_RARP=y
 # CONFIG_IPV6 is not set
+CONFIG_PCCARD=m
+CONFIG_PCMCIA_SA1100=m
 CONFIG_MTD=y
-CONFIG_MTD_REDBOOT_PARTS=y
 CONFIG_MTD_CMDLINE_PARTS=y
+CONFIG_MTD_REDBOOT_PARTS=y
 CONFIG_MTD_BLOCK=y
 CONFIG_MTD_CFI=y
 CONFIG_MTD_CFI_INTELEXT=y
@@ -47,6 +47,10 @@ CONFIG_SERIAL_SA1100_CONSOLE=y
 CONFIG_WATCHDOG=y
 CONFIG_SA1100_WATCHDOG=m
 # CONFIG_VGA_CONSOLE is not set
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=y
+CONFIG_LEDS_TRIGGERS=y
+CONFIG_LEDS_TRIGGER_CPU=y
 CONFIG_EXT2_FS=m
 CONFIG_EXT3_FS=m
 CONFIG_MSDOS_FS=m
@@ -60,11 +64,10 @@ CONFIG_NFS_V4=y
 CONFIG_NFSD=m
 CONFIG_NFSD_V4=y
 CONFIG_SMB_FS=m
-CONFIG_PARTITION_ADVANCED=y
 CONFIG_NLS=y
 CONFIG_NLS_CODEPAGE_437=m
 CONFIG_NLS_ISO8859_1=m
-CONFIG_MAGIC_SYSRQ=y
 CONFIG_DEBUG_KERNEL=y
+CONFIG_MAGIC_SYSRQ=y
 CONFIG_DEBUG_USER=y
 CONFIG_DEBUG_LL=y
diff --git a/arch/arm/configs/clps711x_defconfig b/arch/arm/configs/clps711x_defconfig
index 63a153f5cf68..92481b2a88fa 100644
--- a/arch/arm/configs/clps711x_defconfig
+++ b/arch/arm/configs/clps711x_defconfig
@@ -4,7 +4,6 @@ CONFIG_LOG_BUF_SHIFT=14
 CONFIG_BLK_DEV_INITRD=y
 CONFIG_RD_LZMA=y
 CONFIG_EMBEDDED=y
-CONFIG_SLOB=y
 CONFIG_JUMP_LABEL=y
 CONFIG_PARTITION_ADVANCED=y
 CONFIG_ARCH_CLPS711X=y
@@ -14,16 +13,13 @@ CONFIG_ARCH_CLEP7312=y
 CONFIG_ARCH_EDB7211=y
 CONFIG_ARCH_P720T=y
 CONFIG_AEABI=y
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
 # CONFIG_COREDUMP is not set
+CONFIG_SLOB=y
 CONFIG_NET=y
 CONFIG_PACKET=y
 CONFIG_UNIX=y
 CONFIG_INET=y
 # CONFIG_IPV6 is not set
-CONFIG_IRDA=y
-CONFIG_IRTTY_SIR=y
 # CONFIG_WIRELESS is not set
 CONFIG_MTD=y
 CONFIG_MTD_CMDLINE_PARTS=y
diff --git a/arch/arm/configs/cm_x300_defconfig b/arch/arm/configs/cm_x300_defconfig
index 502a9d870ca4..95144e380b4b 100644
--- a/arch/arm/configs/cm_x300_defconfig
+++ b/arch/arm/configs/cm_x300_defconfig
@@ -1,28 +1,27 @@
 CONFIG_LOCALVERSION="-cm-x300"
 # CONFIG_LOCALVERSION_AUTO is not set
 CONFIG_SYSVIPC=y
+CONFIG_NO_HZ_IDLE=y
 CONFIG_IKCONFIG=y
 CONFIG_IKCONFIG_PROC=y
 CONFIG_LOG_BUF_SHIFT=18
 CONFIG_BLK_DEV_INITRD=y
 # CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
-CONFIG_MODULE_FORCE_UNLOAD=y
-# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_ARCH_MULTI_V7 is not set
 CONFIG_ARCH_PXA=y
-CONFIG_GPIO_PCA953X=y
 CONFIG_MACH_CM_X300=y
-CONFIG_NO_HZ=y
 CONFIG_AEABI=y
 CONFIG_HIGHMEM=y
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_UNUSED_BOARD_FILES=y
 CONFIG_CMDLINE="root=/dev/mtdblock5 rootfstype=ubifs console=ttyS2,38400"
 CONFIG_CPU_FREQ=y
 CONFIG_CPU_FREQ_GOV_USERSPACE=y
 CONFIG_FPE_NWFPE=y
 CONFIG_APM_EMULATION=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_MODULE_FORCE_UNLOAD=y
+CONFIG_PARTITION_ADVANCED=y
 CONFIG_NET=y
 CONFIG_PACKET=y
 CONFIG_UNIX=y
@@ -54,6 +53,7 @@ CONFIG_BLK_DEV_LOOP=y
 CONFIG_BLK_DEV_RAM=y
 CONFIG_SCSI=y
 CONFIG_BLK_DEV_SD=y
+# CONFIG_BLK_DEV_BSG is not set
 CONFIG_NETDEVICES=y
 CONFIG_NET_ETHERNET=y
 CONFIG_DM9000=y
@@ -79,6 +79,7 @@ CONFIG_I2C_PXA=y
 CONFIG_SPI=y
 CONFIG_SPI_GPIO=y
 CONFIG_GPIO_SYSFS=y
+CONFIG_GPIO_PCA953X=y
 # CONFIG_HWMON is not set
 CONFIG_PMIC_DA903X=y
 CONFIG_REGULATOR=y
@@ -90,8 +91,6 @@ CONFIG_LCD_TDO24M=y
 CONFIG_BACKLIGHT_DA903X=m
 CONFIG_FRAMEBUFFER_CONSOLE=y
 CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY=y
-CONFIG_FONTS=y
-CONFIG_FONT_6x11=y
 CONFIG_LOGO=y
 CONFIG_SOUND=m
 CONFIG_SND=m
@@ -146,19 +145,19 @@ CONFIG_NFS_V3_ACL=y
 CONFIG_NFS_V4=y
 CONFIG_ROOT_NFS=y
 CONFIG_CIFS=m
-CONFIG_CIFS_WEAK_PW_HASH=y
-CONFIG_PARTITION_ADVANCED=y
 CONFIG_NLS_CODEPAGE_437=m
 CONFIG_NLS_ISO8859_1=m
-CONFIG_DEBUG_FS=y
+CONFIG_CRYPTO_MICHAEL_MIC=m
+# CONFIG_CRYPTO_HW is not set
+CONFIG_CRC_T10DIF=y
+CONFIG_FONTS=y
+CONFIG_FONT_6x11=y
 CONFIG_DEBUG_KERNEL=y
+CONFIG_DEBUG_FS=y
 # CONFIG_SCHED_DEBUG is not set
 # CONFIG_FTRACE is not set
 CONFIG_DEBUG_USER=y
 CONFIG_DEBUG_LL=y
 CONFIG_CRYPTO_ECB=m
-CONFIG_CRYPTO_MICHAEL_MIC=m
 CONFIG_CRYPTO_AES=m
 # CONFIG_CRYPTO_ANSI_CPRNG is not set
-# CONFIG_CRYPTO_HW is not set
-CONFIG_CRC_T10DIF=y
diff --git a/arch/arm/configs/cns3420vb_defconfig b/arch/arm/configs/cns3420vb_defconfig
index 63fa2eb21b75..b3aab97c0728 100644
--- a/arch/arm/configs/cns3420vb_defconfig
+++ b/arch/arm/configs/cns3420vb_defconfig
@@ -1,5 +1,4 @@
 # CONFIG_LOCALVERSION_AUTO is not set
-# CONFIG_SWAP is not set
 CONFIG_SYSVIPC=y
 CONFIG_IKCONFIG=y
 CONFIG_IKCONFIG_PROC=y
@@ -9,23 +8,22 @@ CONFIG_SYSFS_DEPRECATED_V2=y
 CONFIG_RELAY=y
 CONFIG_BLK_DEV_INITRD=y
 # CONFIG_PERF_EVENTS is not set
-CONFIG_SLAB=y
 CONFIG_PROFILING=y
+CONFIG_ARCH_MULTI_V6=y
+CONFIG_ARCH_CNS3XXX=y
+CONFIG_MACH_CNS3420VB=y
+CONFIG_UNUSED_BOARD_FILES=y
+CONFIG_CMDLINE="console=ttyS0,38400 mem=128M root=/dev/mmcblk0p1 ro rootwait"
 CONFIG_MODULES=y
 CONFIG_MODULE_UNLOAD=y
 CONFIG_MODULE_FORCE_UNLOAD=y
 CONFIG_MODVERSIONS=y
-# CONFIG_BLK_DEV_BSG is not set
 CONFIG_IOSCHED_BFQ=m
-CONFIG_ARCH_MULTI_V6=y
 #CONFIG_ARCH_MULTI_V7 is not set
-CONFIG_ARCH_CNS3XXX=y
-CONFIG_MACH_CNS3420VB=y
 CONFIG_DEBUG_CNS3XXX=y
 CONFIG_AEABI=y
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
-CONFIG_CMDLINE="console=ttyS0,38400 mem=128M root=/dev/mmcblk0p1 ro rootwait"
+# CONFIG_SWAP is not set
+CONFIG_SLAB=y
 CONFIG_MTD=y
 CONFIG_MTD_CMDLINE_PARTS=y
 CONFIG_MTD_BLOCK=y
@@ -36,6 +34,7 @@ CONFIG_BLK_DEV_LOOP=y
 CONFIG_BLK_DEV_RAM=y
 CONFIG_BLK_DEV_RAM_SIZE=20000
 CONFIG_BLK_DEV_SD=y
+# CONFIG_BLK_DEV_BSG is not set
 CONFIG_ATA=y
 # CONFIG_SATA_PMP is not set
 # CONFIG_ATA_SFF is not set
@@ -43,9 +42,9 @@ CONFIG_ATA=y
 # CONFIG_INPUT_KEYBOARD is not set
 # CONFIG_INPUT_MOUSE is not set
 # CONFIG_SERIO is not set
+CONFIG_LEGACY_PTY_COUNT=16
 CONFIG_SERIAL_8250=y
 CONFIG_SERIAL_8250_CONSOLE=y
-CONFIG_LEGACY_PTY_COUNT=16
 # CONFIG_HW_RANDOM is not set
 # CONFIG_HWMON is not set
 # CONFIG_VGA_CONSOLE is not set
@@ -59,6 +58,6 @@ CONFIG_AUTOFS4_FS=y
 CONFIG_FSCACHE=y
 CONFIG_TMPFS=y
 # CONFIG_ENABLE_MUST_CHECK is not set
-CONFIG_DEBUG_FS=y
 # CONFIG_ARM_UNWIND is not set
 CONFIG_CRC_CCITT=y
+CONFIG_DEBUG_FS=y
diff --git a/arch/arm/configs/colibri_pxa270_defconfig b/arch/arm/configs/colibri_pxa270_defconfig
index 52bad9a544a0..8357d721c69c 100644
--- a/arch/arm/configs/colibri_pxa270_defconfig
+++ b/arch/arm/configs/colibri_pxa270_defconfig
@@ -1,5 +1,6 @@
 CONFIG_SYSVIPC=y
 CONFIG_POSIX_MQUEUE=y
+CONFIG_PREEMPT=y
 CONFIG_BSD_PROCESS_ACCT=y
 CONFIG_BSD_PROCESS_ACCT_V3=y
 CONFIG_IKCONFIG=y
@@ -9,19 +10,20 @@ CONFIG_SYSFS_DEPRECATED_V2=y
 CONFIG_BLK_DEV_INITRD=y
 CONFIG_EXPERT=y
 CONFIG_KALLSYMS_EXTRA_PASS=y
-CONFIG_SLAB=y
+# CONFIG_ARCH_MULTI_V7 is not set
+CONFIG_ARCH_PXA=y
+CONFIG_MACH_COLIBRI=y
+CONFIG_AEABI=y
+CONFIG_UNUSED_BOARD_FILES=y
 CONFIG_MODULES=y
 CONFIG_MODULE_UNLOAD=y
 CONFIG_MODULE_FORCE_UNLOAD=y
 CONFIG_MODVERSIONS=y
 CONFIG_MODULE_SRCVERSION_ALL=y
 # CONFIG_BLK_DEV_BSG is not set
-CONFIG_ARCH_PXA=y
-CONFIG_MACH_COLIBRI=y
-CONFIG_PREEMPT=y
-CONFIG_AEABI=y
 CONFIG_FPE_NWFPE=y
 CONFIG_PM=y
+CONFIG_SLAB=y
 CONFIG_NET=y
 CONFIG_PACKET=y
 CONFIG_UNIX=y
@@ -34,13 +36,6 @@ CONFIG_IP_PNP_BOOTP=y
 # CONFIG_IPV6 is not set
 CONFIG_NETFILTER=y
 CONFIG_VLAN_8021Q=m
-CONFIG_IRDA=m
-CONFIG_IRLAN=m
-CONFIG_IRCOMM=m
-CONFIG_IRDA_ULTRA=y
-CONFIG_IRDA_CACHE_LAST_LSAP=y
-CONFIG_IRDA_FAST_RR=y
-CONFIG_IRTTY_SIR=m
 CONFIG_BT=m
 CONFIG_BT_RFCOMM=m
 CONFIG_BT_RFCOMM_TTY=y
@@ -63,22 +58,22 @@ CONFIG_MTD_COMPLEX_MAPPINGS=y
 CONFIG_MTD_PHYSMAP=y
 CONFIG_MTD_PXA2XX=y
 CONFIG_MTD_BLOCK2MTD=y
+CONFIG_MTD_ONENAND=y
 CONFIG_MTD_RAW_NAND=y
 CONFIG_MTD_NAND_DISKONCHIP=y
 CONFIG_MTD_NAND_DISKONCHIP_PROBE_ADVANCED=y
 CONFIG_MTD_NAND_DISKONCHIP_PROBE_ADDRESS=0x4000000
 CONFIG_MTD_NAND_DISKONCHIP_PROBE_HIGH=y
 CONFIG_MTD_NAND_DISKONCHIP_BBTWRITE=y
-CONFIG_MTD_ONENAND=y
 CONFIG_BLK_DEV_LOOP=y
 CONFIG_BLK_DEV_CRYPTOLOOP=m
 CONFIG_BLK_DEV_NBD=y
 CONFIG_BLK_DEV_RAM=y
 CONFIG_BLK_DEV_RAM_COUNT=8
 CONFIG_NETDEVICES=y
-CONFIG_PHYLIB=y
 CONFIG_NET_ETHERNET=y
 CONFIG_DM9000=y
+CONFIG_PHYLIB=y
 CONFIG_HOSTAP=y
 CONFIG_HOSTAP_FIRMWARE=y
 CONFIG_HOSTAP_FIRMWARE_NVRAM=y
@@ -106,9 +101,6 @@ CONFIG_BACKLIGHT_CLASS_DEVICE=y
 # CONFIG_VGA_CONSOLE is not set
 CONFIG_FRAMEBUFFER_CONSOLE=y
 CONFIG_FRAMEBUFFER_CONSOLE_ROTATION=y
-CONFIG_FONTS=y
-CONFIG_FONT_8x8=y
-CONFIG_FONT_8x16=y
 CONFIG_LOGO=y
 # CONFIG_USB_HID is not set
 CONFIG_USB=y
@@ -142,13 +134,8 @@ CONFIG_NLS_ASCII=y
 CONFIG_NLS_ISO8859_1=m
 CONFIG_NLS_ISO8859_15=m
 CONFIG_NLS_UTF8=m
-CONFIG_PRINTK_TIME=y
-CONFIG_MAGIC_SYSRQ=y
-CONFIG_DEBUG_FS=y
 CONFIG_DEBUG_KERNEL=y
-CONFIG_DEBUG_INFO=y
-CONFIG_DEBUG_USER=y
-CONFIG_DEBUG_LL=y
+CONFIG_DEBUG_INFO_DWARF_TOOLCHAIN_DEFAULT=y
 CONFIG_KEYS=y
 CONFIG_SECURITY=y
 CONFIG_CRYPTO_PCBC=m
@@ -160,3 +147,11 @@ CONFIG_CRYPTO_DEFLATE=m
 CONFIG_CRC_CCITT=y
 CONFIG_CRC16=y
 CONFIG_LIBCRC32C=y
+CONFIG_FONTS=y
+CONFIG_FONT_8x8=y
+CONFIG_FONT_8x16=y
+CONFIG_PRINTK_TIME=y
+CONFIG_MAGIC_SYSRQ=y
+CONFIG_DEBUG_FS=y
+CONFIG_DEBUG_USER=y
+CONFIG_DEBUG_LL=y
diff --git a/arch/arm/configs/colibri_pxa300_defconfig b/arch/arm/configs/colibri_pxa300_defconfig
index 26e5a67f8e2d..42adfefdb6dc 100644
--- a/arch/arm/configs/colibri_pxa300_defconfig
+++ b/arch/arm/configs/colibri_pxa300_defconfig
@@ -1,12 +1,13 @@
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
-# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_ARCH_MULTI_V7 is not set
 CONFIG_ARCH_PXA=y
 CONFIG_MACH_COLIBRI300=y
 CONFIG_AEABI=y
+CONFIG_UNUSED_BOARD_FILES=y
 CONFIG_CMDLINE="console=ttyS0,115200 rw"
 CONFIG_CPU_IDLE=y
 CONFIG_FPE_NWFPE=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
 CONFIG_NET=y
 CONFIG_UNIX=y
 CONFIG_INET=y
@@ -17,6 +18,7 @@ CONFIG_IPV6=y
 CONFIG_SCSI=y
 CONFIG_BLK_DEV_SD=y
 CONFIG_CHR_DEV_SG=y
+# CONFIG_BLK_DEV_BSG is not set
 CONFIG_NETDEVICES=y
 CONFIG_NET_ETHERNET=y
 CONFIG_AX88796=y
@@ -47,12 +49,12 @@ CONFIG_EXT3_FS=y
 CONFIG_NFS_FS=y
 CONFIG_NFS_V3=y
 CONFIG_ROOT_NFS=y
+CONFIG_CRYPTO_ECB=y
+CONFIG_CRYPTO_AES=y
 CONFIG_PRINTK_TIME=y
 CONFIG_DEBUG_KERNEL=y
-CONFIG_DEBUG_INFO=y
+CONFIG_DEBUG_INFO_DWARF_TOOLCHAIN_DEFAULT=y
 CONFIG_DEBUG_USER=y
 CONFIG_DEBUG_LL=y
-CONFIG_CRYPTO_ECB=y
-CONFIG_CRYPTO_AES=y
 CONFIG_CRYPTO_ARC4=y
 # CONFIG_CRYPTO_ANSI_CPRNG is not set
diff --git a/arch/arm/configs/collie_defconfig b/arch/arm/configs/collie_defconfig
index 36384fd575f8..2a2d2cb3ce2e 100644
--- a/arch/arm/configs/collie_defconfig
+++ b/arch/arm/configs/collie_defconfig
@@ -1,4 +1,3 @@
-# CONFIG_SWAP is not set
 CONFIG_SYSVIPC=y
 CONFIG_LOG_BUF_SHIFT=14
 CONFIG_BLK_DEV_INITRD=y
@@ -6,22 +5,23 @@ CONFIG_BLK_DEV_INITRD=y
 CONFIG_EXPERT=y
 # CONFIG_BASE_FULL is not set
 # CONFIG_EPOLL is not set
-CONFIG_SLOB=y
+CONFIG_ARCH_MULTI_V4=y
+# CONFIG_ARCH_MULTI_V7 is not set
 CONFIG_ARCH_SA1100=y
 CONFIG_SA1100_COLLIE=y
-CONFIG_PCCARD=y
-CONFIG_PCMCIA_SA1100=y
-CONFIG_PCMCIA_DEBUG=y
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
 CONFIG_CMDLINE="noinitrd root=/dev/mtdblock2 rootfstype=jffs2 fbcon=rotate:1"
 CONFIG_FPE_NWFPE=y
 CONFIG_PM=y
+# CONFIG_SWAP is not set
+CONFIG_SLOB=y
 CONFIG_NET=y
 CONFIG_PACKET=y
 CONFIG_UNIX=y
 CONFIG_INET=y
 # CONFIG_IPV6 is not set
+CONFIG_PCCARD=y
+CONFIG_PCMCIA_SA1100=y
+CONFIG_PCMCIA_DEBUG=y
 CONFIG_MTD=y
 CONFIG_MTD_BLOCK=y
 CONFIG_MTD_CFI=y
@@ -48,12 +48,12 @@ CONFIG_KEYBOARD_LOCOMO=y
 # CONFIG_INPUT_MOUSE is not set
 CONFIG_INPUT_TOUCHSCREEN=y
 # CONFIG_SERIO_SERPORT is not set
+# CONFIG_LEGACY_PTYS is not set
 CONFIG_SERIAL_8250=y
 CONFIG_SERIAL_8250_CS=y
 CONFIG_SERIAL_8250_EXTENDED=y
 CONFIG_SERIAL_SA1100=y
 CONFIG_SERIAL_SA1100_CONSOLE=y
-# CONFIG_LEGACY_PTYS is not set
 # CONFIG_HWMON is not set
 CONFIG_MCP_SA11X0=y
 CONFIG_MCP_UCB1200=y
@@ -64,8 +64,6 @@ CONFIG_FB_SA1100=y
 # CONFIG_VGA_CONSOLE is not set
 CONFIG_FRAMEBUFFER_CONSOLE=y
 CONFIG_FRAMEBUFFER_CONSOLE_ROTATION=y
-CONFIG_FONTS=y
-CONFIG_FONT_MINI_4x6=y
 CONFIG_NEW_LEDS=y
 CONFIG_LEDS_CLASS=y
 CONFIG_LEDS_LOCOMO=y
@@ -80,9 +78,11 @@ CONFIG_ROMFS_FS=y
 CONFIG_NLS_DEFAULT="cp437"
 CONFIG_NLS_CODEPAGE_437=y
 CONFIG_NLS_ISO8859_1=y
+CONFIG_CRC_CCITT=y
+CONFIG_FONTS=y
+CONFIG_FONT_MINI_4x6=y
+# CONFIG_DEBUG_BUGVERBOSE is not set
 CONFIG_MAGIC_SYSRQ=y
 CONFIG_DEBUG_KERNEL=y
 # CONFIG_DETECT_SOFTLOCKUP is not set
 CONFIG_DEBUG_MUTEXES=y
-# CONFIG_DEBUG_BUGVERBOSE is not set
-CONFIG_CRC_CCITT=y
diff --git a/arch/arm/configs/corgi_defconfig b/arch/arm/configs/corgi_defconfig
index 15b749f6996d..df84640f4f57 100644
--- a/arch/arm/configs/corgi_defconfig
+++ b/arch/arm/configs/corgi_defconfig
@@ -1,28 +1,25 @@
 CONFIG_SYSVIPC=y
+CONFIG_PREEMPT=y
 CONFIG_BSD_PROCESS_ACCT=y
 CONFIG_LOG_BUF_SHIFT=14
 CONFIG_SYSFS_DEPRECATED_V2=y
 # CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
 CONFIG_EXPERT=y
 CONFIG_PROFILING=y
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
-CONFIG_MODULE_FORCE_UNLOAD=y
-# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_ARCH_MULTI_V7 is not set
 CONFIG_ARCH_PXA=y
 CONFIG_PXA_SHARPSL=y
 CONFIG_MACH_POODLE=y
 CONFIG_MACH_CORGI=y
 CONFIG_MACH_SHEPHERD=y
 CONFIG_MACH_HUSKY=y
-CONFIG_PCCARD=y
-CONFIG_PCMCIA_PXA2XX=y
-CONFIG_PREEMPT=y
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_UNUSED_BOARD_FILES=y
 CONFIG_CMDLINE="console=ttyS0,115200n8 console=tty1 noinitrd root=/dev/mtdblock2 rootfstype=jffs2   debug"
 CONFIG_FPE_NWFPE=y
-CONFIG_BINFMT_AOUT=m
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_MODULE_FORCE_UNLOAD=y
+CONFIG_PARTITION_ADVANCED=y
 CONFIG_BINFMT_MISC=m
 CONFIG_PM=y
 CONFIG_NET=y
@@ -57,11 +54,6 @@ CONFIG_IP6_NF_MATCH_RT=m
 CONFIG_IP6_NF_FILTER=m
 CONFIG_IP6_NF_MANGLE=m
 CONFIG_IP6_NF_RAW=m
-CONFIG_IRDA=m
-CONFIG_IRLAN=m
-CONFIG_IRNET=m
-CONFIG_IRCOMM=m
-CONFIG_PXA_FICP=m
 CONFIG_BT=m
 CONFIG_BT_RFCOMM=m
 CONFIG_BT_RFCOMM_TTY=y
@@ -80,6 +72,8 @@ CONFIG_BT_HCIBT3C=m
 CONFIG_BT_HCIBLUECARD=m
 CONFIG_BT_HCIBTUART=m
 CONFIG_BT_HCIVHCI=m
+CONFIG_PCCARD=y
+CONFIG_PCMCIA_PXA2XX=y
 CONFIG_MTD=y
 CONFIG_MTD_CMDLINE_PARTS=y
 CONFIG_MTD_BLOCK=y
@@ -94,10 +88,15 @@ CONFIG_CHR_DEV_OSST=m
 CONFIG_BLK_DEV_SR=m
 CONFIG_CHR_DEV_SG=m
 CONFIG_SCSI_MULTI_LUN=y
+# CONFIG_BLK_DEV_BSG is not set
 CONFIG_ATA=y
 CONFIG_PATA_PCMCIA=y
 CONFIG_NETDEVICES=y
 CONFIG_NET_ETHERNET=y
+CONFIG_PCMCIA_PCNET=m
+CONFIG_PPP=m
+CONFIG_PPP_BSDCOMP=m
+CONFIG_PPP_ASYNC=m
 CONFIG_USB_CATC=m
 CONFIG_USB_KAWETH=m
 CONFIG_USB_PEGASUS=m
@@ -105,10 +104,6 @@ CONFIG_USB_RTL8150=m
 CONFIG_USB_USBNET=m
 # CONFIG_USB_NET_CDC_SUBSET is not set
 CONFIG_NET_PCMCIA=y
-CONFIG_PCMCIA_PCNET=m
-CONFIG_PPP=m
-CONFIG_PPP_ASYNC=m
-CONFIG_PPP_BSDCOMP=m
 CONFIG_INPUT_FF_MEMLESS=m
 # CONFIG_INPUT_MOUSEDEV is not set
 CONFIG_INPUT_EVDEV=y
@@ -119,11 +114,11 @@ CONFIG_TOUCHSCREEN_ADS7846=y
 CONFIG_INPUT_MISC=y
 CONFIG_INPUT_UINPUT=m
 # CONFIG_SERIO is not set
+# CONFIG_LEGACY_PTYS is not set
 CONFIG_SERIAL_8250=m
 CONFIG_SERIAL_8250_CS=m
 CONFIG_SERIAL_PXA=y
 CONFIG_SERIAL_PXA_CONSOLE=y
-# CONFIG_LEGACY_PTYS is not set
 CONFIG_I2C=y
 CONFIG_I2C_PXA=y
 CONFIG_SPI=y
@@ -135,13 +130,8 @@ CONFIG_LCD_CORGI=y
 CONFIG_BACKLIGHT_CLASS_DEVICE=y
 # CONFIG_VGA_CONSOLE is not set
 CONFIG_FRAMEBUFFER_CONSOLE=y
-CONFIG_FONTS=y
-CONFIG_FONT_8x8=y
-CONFIG_FONT_8x16=y
 CONFIG_SOUND=y
 CONFIG_SOUND_PRIME=y
-CONFIG_USB_KBD=m
-CONFIG_USB_MOUSE=m
 CONFIG_HID_A4TECH=m
 CONFIG_HID_APPLE=m
 CONFIG_HID_BELKIN=m
@@ -158,6 +148,8 @@ CONFIG_HID_PETALYNX=m
 CONFIG_HID_SAMSUNG=m
 CONFIG_HID_SONY=m
 CONFIG_HID_SUNPLUS=m
+CONFIG_USB_KBD=m
+CONFIG_USB_MOUSE=m
 CONFIG_USB=m
 CONFIG_USB_MON=m
 CONFIG_USB_SL811_HCD=m
@@ -219,16 +211,12 @@ CONFIG_NFS_V3=y
 CONFIG_NFS_V4=y
 CONFIG_SMB_FS=m
 CONFIG_SMB_NLS_DEFAULT=y
-CONFIG_PARTITION_ADVANCED=y
+CONFIG_NFS_V4=m
 CONFIG_NLS_DEFAULT="cp437"
 CONFIG_NLS_CODEPAGE_437=y
 CONFIG_NLS_ISO8859_1=y
 CONFIG_NLS_UTF8=y
-CONFIG_MAGIC_SYSRQ=y
 CONFIG_DEBUG_KERNEL=y
-# CONFIG_DEBUG_PREEMPT is not set
-# CONFIG_FTRACE is not set
-CONFIG_DEBUG_LL=y
 CONFIG_CRYPTO_NULL=m
 CONFIG_CRYPTO_TEST=m
 CONFIG_CRYPTO_ECB=m
@@ -251,3 +239,9 @@ CONFIG_CRYPTO_TWOFISH=m
 # CONFIG_CRYPTO_ANSI_CPRNG is not set
 CONFIG_CRC_CCITT=y
 CONFIG_LIBCRC32C=m
+CONFIG_FONTS=y
+CONFIG_FONT_8x8=y
+CONFIG_FONT_8x16=y
+CONFIG_MAGIC_SYSRQ=y
+# CONFIG_DEBUG_PREEMPT is not set
+# CONFIG_FTRACE is not set
diff --git a/arch/arm/configs/davinci_all_defconfig b/arch/arm/configs/davinci_all_defconfig
index e849367c0566..821d966c95a5 100644
--- a/arch/arm/configs/davinci_all_defconfig
+++ b/arch/arm/configs/davinci_all_defconfig
@@ -1,8 +1,8 @@
-# CONFIG_SWAP is not set
 CONFIG_SYSVIPC=y
 CONFIG_POSIX_MQUEUE=y
-CONFIG_NO_HZ=y
+CONFIG_NO_HZ_IDLE=y
 CONFIG_HIGH_RES_TIMERS=y
+CONFIG_PREEMPT=y
 CONFIG_IKCONFIG=y
 CONFIG_IKCONFIG_PROC=y
 CONFIG_LOG_BUF_SHIFT=14
@@ -10,34 +10,16 @@ CONFIG_CGROUPS=y
 CONFIG_CHECKPOINT_RESTORE=y
 CONFIG_BLK_DEV_INITRD=y
 CONFIG_EXPERT=y
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
-CONFIG_MODULE_FORCE_UNLOAD=y
-CONFIG_MODVERSIONS=y
-CONFIG_PARTITION_ADVANCED=y
 CONFIG_ARCH_MULTIPLATFORM=y
-CONFIG_ARCH_MULTI_V7=n
 CONFIG_ARCH_MULTI_V5=y
+# CONFIG_ARCH_MULTI_V7 is not set
 CONFIG_ARCH_DAVINCI=y
-CONFIG_ARCH_DAVINCI_DM644x=y
-CONFIG_ARCH_DAVINCI_DM355=y
-CONFIG_ARCH_DAVINCI_DM646x=y
 CONFIG_ARCH_DAVINCI_DA830=y
 CONFIG_ARCH_DAVINCI_DA850=y
-CONFIG_ARCH_DAVINCI_DM365=y
-CONFIG_MACH_SFFSDR=y
-CONFIG_MACH_NEUROS_OSD2=y
-CONFIG_MACH_DM355_LEOPARD=y
-CONFIG_MACH_MITYOMAPL138=y
-CONFIG_MACH_OMAPL138_HAWKBOARD=y
 CONFIG_DAVINCI_MUX_DEBUG=y
 CONFIG_DAVINCI_MUX_WARNINGS=y
-CONFIG_PREEMPT=y
 CONFIG_AEABI=y
-CONFIG_CMA=y
 CONFIG_SECCOMP=y
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
 CONFIG_ARM_APPENDED_DTB=y
 CONFIG_ARM_ATAG_DTB_COMPAT=y
 CONFIG_AUTO_ZRELADDR=y
@@ -48,6 +30,13 @@ CONFIG_CPU_FREQ_GOV_POWERSAVE=m
 CONFIG_CPU_FREQ_GOV_ONDEMAND=m
 CONFIG_CPUFREQ_DT=m
 CONFIG_CPU_IDLE=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_MODULE_FORCE_UNLOAD=y
+CONFIG_MODVERSIONS=y
+CONFIG_PARTITION_ADVANCED=y
+# CONFIG_SWAP is not set
+CONFIG_CMA=y
 CONFIG_NET=y
 CONFIG_PACKET=y
 CONFIG_UNIX=y
@@ -65,7 +54,6 @@ CONFIG_BT_HCIUART_LL=y
 CONFIG_DEVTMPFS=y
 CONFIG_DEVTMPFS_MOUNT=y
 CONFIG_FW_LOADER=m
-CONFIG_DMA_CMA=y
 CONFIG_DA8XX_MSTPRI=y
 CONFIG_MTD=m
 CONFIG_MTD_TESTS=m
@@ -95,8 +83,8 @@ CONFIG_NETCONSOLE=y
 CONFIG_TUN=m
 CONFIG_DM9000=y
 CONFIG_TI_DAVINCI_EMAC=y
-CONFIG_LSI_ET1011C_PHY=y
 CONFIG_LXT_PHY=y
+CONFIG_LSI_ET1011C_PHY=y
 CONFIG_SMSC_PHY=y
 CONFIG_PPP=m
 CONFIG_PPP_DEFLATE=m
@@ -113,7 +101,6 @@ CONFIG_KEYBOARD_XTKBD=m
 CONFIG_INPUT_TOUCHSCREEN=y
 CONFIG_INPUT_MISC=y
 CONFIG_INPUT_PWM_BEEPER=m
-CONFIG_INPUT_DM355EVM=m
 CONFIG_SERIO_LIBPS2=y
 # CONFIG_VT_CONSOLE is not set
 CONFIG_SERIAL_8250=y
@@ -141,7 +128,6 @@ CONFIG_SYSCON_REBOOT_MODE=m
 CONFIG_BATTERY_LEGO_EV3=m
 CONFIG_WATCHDOG=y
 CONFIG_DAVINCI_WATCHDOG=y
-CONFIG_MFD_DM355EVM_MSP=y
 CONFIG_TPS6507X=y
 CONFIG_REGULATOR=y
 CONFIG_REGULATOR_FIXED_VOLTAGE=y
@@ -258,15 +244,15 @@ CONFIG_MINIX_FS=m
 CONFIG_NFS_FS=y
 CONFIG_ROOT_NFS=y
 CONFIG_NFSD=m
-CONFIG_NFSD_V3=y
 CONFIG_NLS_CODEPAGE_437=y
 CONFIG_NLS_ASCII=m
 CONFIG_NLS_ISO8859_1=y
 CONFIG_NLS_UTF8=m
+# CONFIG_CRYPTO_HW is not set
+CONFIG_CRC_T10DIF=m
+CONFIG_DMA_CMA=y
 CONFIG_DEBUG_FS=y
 CONFIG_DEBUG_RT_MUTEXES=y
 CONFIG_DEBUG_MUTEXES=y
 # CONFIG_ARM_UNWIND is not set
 CONFIG_DEBUG_USER=y
-# CONFIG_CRYPTO_HW is not set
-CONFIG_CRC_T10DIF=m
diff --git a/arch/arm/configs/dove_defconfig b/arch/arm/configs/dove_defconfig
index 33074fdab2ea..ff37f46c82fb 100644
--- a/arch/arm/configs/dove_defconfig
+++ b/arch/arm/configs/dove_defconfig
@@ -1,27 +1,23 @@
 CONFIG_SYSVIPC=y
-CONFIG_NO_HZ=y
+CONFIG_NO_HZ_IDLE=y
 CONFIG_HIGH_RES_TIMERS=y
 CONFIG_LOG_BUF_SHIFT=14
 CONFIG_EXPERT=y
-CONFIG_SLAB=y
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
-# CONFIG_BLK_DEV_BSG is not set
-CONFIG_PARTITION_ADVANCED=y
+# CONFIG_ARCH_MULTI_V6 is not set
+CONFIG_ARCH_MULTI_V7=y
 CONFIG_ARCH_DOVE=y
 CONFIG_MACH_DOVE_DB=y
 CONFIG_MACH_CM_A510=y
 CONFIG_MACH_DOVE_DT=y
-CONFIG_PCI=y
-CONFIG_PCI_MSI=y
-CONFIG_PCI_MVEBU=y
 CONFIG_AEABI=y
 CONFIG_HIGHMEM=y
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
 CONFIG_ARM_APPENDED_DTB=y
 CONFIG_ARM_ATAG_DTB_COMPAT=y
 CONFIG_VFP=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_PARTITION_ADVANCED=y
+CONFIG_SLAB=y
 CONFIG_NET=y
 CONFIG_PACKET=y
 CONFIG_UNIX=y
@@ -31,6 +27,9 @@ CONFIG_IP_PNP=y
 CONFIG_IP_PNP_DHCP=y
 CONFIG_IP_PNP_BOOTP=y
 # CONFIG_IPV6 is not set
+CONFIG_PCI=y
+CONFIG_PCI_MSI=y
+CONFIG_PCI_MVEBU=y
 CONFIG_DEVTMPFS=y
 CONFIG_DEVTMPFS_MOUNT=y
 CONFIG_MTD=y
@@ -51,6 +50,7 @@ CONFIG_BLK_DEV_RAM=y
 CONFIG_BLK_DEV_RAM_COUNT=1
 # CONFIG_SCSI_PROC_FS is not set
 CONFIG_BLK_DEV_SD=y
+# CONFIG_BLK_DEV_BSG is not set
 # CONFIG_SCSI_LOWLEVEL is not set
 CONFIG_ATA=y
 CONFIG_SATA_MV=y
@@ -115,14 +115,7 @@ CONFIG_NLS_CODEPAGE_850=y
 CONFIG_NLS_ISO8859_1=y
 CONFIG_NLS_ISO8859_2=y
 CONFIG_NLS_UTF8=y
-CONFIG_PRINTK_TIME=y
-CONFIG_MAGIC_SYSRQ=y
-CONFIG_DEBUG_FS=y
-# CONFIG_SCHED_DEBUG is not set
 CONFIG_TIMER_STATS=y
-# CONFIG_DEBUG_BUGVERBOSE is not set
-CONFIG_DEBUG_INFO=y
-CONFIG_DEBUG_USER=y
 CONFIG_CRYPTO_NULL=y
 CONFIG_CRYPTO_ECB=m
 CONFIG_CRYPTO_PCBC=m
@@ -140,3 +133,10 @@ CONFIG_CRYPTO_LZO=y
 CONFIG_CRYPTO_DEV_MARVELL_CESA=y
 CONFIG_CRC_CCITT=y
 CONFIG_LIBCRC32C=y
+CONFIG_PRINTK_TIME=y
+# CONFIG_DEBUG_BUGVERBOSE is not set
+CONFIG_DEBUG_INFO_DWARF_TOOLCHAIN_DEFAULT=y
+CONFIG_MAGIC_SYSRQ=y
+CONFIG_DEBUG_FS=y
+# CONFIG_SCHED_DEBUG is not set
+CONFIG_DEBUG_USER=y
diff --git a/arch/arm/configs/ep93xx_defconfig b/arch/arm/configs/ep93xx_defconfig
index 88d5ecc2121e..3154125321c5 100644
--- a/arch/arm/configs/ep93xx_defconfig
+++ b/arch/arm/configs/ep93xx_defconfig
@@ -5,14 +5,9 @@ CONFIG_IKCONFIG=y
 CONFIG_IKCONFIG_PROC=y
 CONFIG_LOG_BUF_SHIFT=14
 CONFIG_EXPERT=y
-CONFIG_SLAB=y
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
-CONFIG_MODULE_FORCE_UNLOAD=y
-# CONFIG_BLK_DEV_BSG is not set
-CONFIG_PARTITION_ADVANCED=y
+CONFIG_ARCH_MULTI_V4T=y
+# CONFIG_ARCH_MULTI_V7 is not set
 CONFIG_ARCH_EP93XX=y
-CONFIG_MACH_ADSSPHERE=y
 CONFIG_MACH_EDB9301=y
 CONFIG_MACH_EDB9302=y
 CONFIG_MACH_EDB9302A=y
@@ -21,19 +16,15 @@ CONFIG_MACH_EDB9307A=y
 CONFIG_MACH_EDB9312=y
 CONFIG_MACH_EDB9315=y
 CONFIG_MACH_EDB9315A=y
-CONFIG_MACH_GESBC9312=y
-CONFIG_MACH_MICRO9H=y
-CONFIG_MACH_MICRO9M=y
-CONFIG_MACH_MICRO9L=y
-CONFIG_MACH_MICRO9S=y
-CONFIG_MACH_SIM_ONE=y
-CONFIG_MACH_SNAPPER_CL15=y
 CONFIG_MACH_TS72XX=y
 CONFIG_MACH_VISION_EP9307=y
 CONFIG_AEABI=y
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
 CONFIG_CMDLINE="console=ttyAM0,115200 root=/dev/nfs ip=bootp"
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_MODULE_FORCE_UNLOAD=y
+CONFIG_PARTITION_ADVANCED=y
+CONFIG_SLAB=y
 CONFIG_NET=y
 CONFIG_PACKET=y
 CONFIG_UNIX=y
@@ -50,8 +41,8 @@ CONFIG_IPV6=y
 # CONFIG_IPV6_SIT is not set
 # CONFIG_FW_LOADER is not set
 CONFIG_MTD=y
-CONFIG_MTD_REDBOOT_PARTS=y
 CONFIG_MTD_CMDLINE_PARTS=y
+CONFIG_MTD_REDBOOT_PARTS=y
 CONFIG_MTD_BLOCK=y
 CONFIG_MTD_CFI=y
 CONFIG_MTD_CFI_ADV_OPTIONS=y
@@ -66,6 +57,7 @@ CONFIG_EEPROM_LEGACY=y
 CONFIG_SCSI=y
 # CONFIG_SCSI_PROC_FS is not set
 CONFIG_BLK_DEV_SD=y
+# CONFIG_BLK_DEV_BSG is not set
 CONFIG_NETDEVICES=y
 CONFIG_EP93XX_ETH=y
 CONFIG_USB_RTL8150=y
@@ -122,6 +114,7 @@ CONFIG_NFS_FS=y
 CONFIG_ROOT_NFS=y
 CONFIG_NLS_CODEPAGE_437=y
 CONFIG_NLS_ISO8859_1=y
+CONFIG_LIBCRC32C=y
 CONFIG_MAGIC_SYSRQ=y
 CONFIG_DEBUG_SLAB=y
 CONFIG_DEBUG_SPINLOCK=y
@@ -129,4 +122,3 @@ CONFIG_DEBUG_MUTEXES=y
 CONFIG_DEBUG_USER=y
 CONFIG_DEBUG_LL=y
 # CONFIG_CRYPTO_ANSI_CPRNG is not set
-CONFIG_LIBCRC32C=y
diff --git a/arch/arm/configs/eseries_pxa_defconfig b/arch/arm/configs/eseries_pxa_defconfig
index 046f4dc2e18e..b4c2e6457e04 100644
--- a/arch/arm/configs/eseries_pxa_defconfig
+++ b/arch/arm/configs/eseries_pxa_defconfig
@@ -3,41 +3,33 @@ CONFIG_LOG_BUF_SHIFT=14
 # CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
 CONFIG_EXPERT=y
 # CONFIG_KALLSYMS is not set
-# CONFIG_COMPAT_BRK is not set
-CONFIG_SLAB=y
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
-CONFIG_MODULE_FORCE_UNLOAD=y
-# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_ARCH_MULTI_V7 is not set
 CONFIG_ARCH_PXA=y
 CONFIG_ARCH_PXA_ESERIES=y
-# CONFIG_ARM_THUMB is not set
 CONFIG_IWMMXT=y
-CONFIG_PCCARD=y
-CONFIG_PCMCIA=m
-CONFIG_PCMCIA_PXA2XX=m
 CONFIG_AEABI=y
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_UNUSED_BOARD_FILES=y
 CONFIG_KEXEC=y
 CONFIG_FPE_NWFPE=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_MODULE_FORCE_UNLOAD=y
+CONFIG_PARTITION_ADVANCED=y
 CONFIG_BINFMT_MISC=y
 CONFIG_PM=y
+CONFIG_SLAB=y
+# CONFIG_COMPAT_BRK is not set
 CONFIG_NET=y
 CONFIG_UNIX=y
 CONFIG_INET=y
 # CONFIG_IPV6 is not set
-CONFIG_IRDA=y
-CONFIG_IRLAN=m
-CONFIG_IRCOMM=m
-CONFIG_IRDA_ULTRA=y
-CONFIG_IRDA_CACHE_LAST_LSAP=y
-CONFIG_IRDA_FAST_RR=y
-CONFIG_PXA_FICP=y
 CONFIG_CFG80211=m
 CONFIG_MAC80211=m
 CONFIG_MAC80211_RC_PID=y
 # CONFIG_MAC80211_RC_MINSTREL is not set
+CONFIG_PCCARD=y
+CONFIG_PCMCIA=m
+CONFIG_PCMCIA_PXA2XX=m
 # CONFIG_STANDALONE is not set
 CONFIG_MTD=m
 CONFIG_MTD_RAW_NAND=m
@@ -45,6 +37,7 @@ CONFIG_MTD_NAND_TMIO=m
 CONFIG_BLK_DEV_LOOP=m
 # CONFIG_SCSI_PROC_FS is not set
 CONFIG_BLK_DEV_SD=m
+# CONFIG_BLK_DEV_BSG is not set
 # CONFIG_SCSI_LOWLEVEL is not set
 CONFIG_ATA=m
 # CONFIG_SATA_PMP is not set
@@ -61,8 +54,8 @@ CONFIG_KEYBOARD_GPIO=m
 CONFIG_INPUT_TOUCHSCREEN=y
 CONFIG_TOUCHSCREEN_WM97XX=m
 # CONFIG_SERIO is not set
-CONFIG_SERIAL_PXA=y
 # CONFIG_LEGACY_PTYS is not set
+CONFIG_SERIAL_PXA=y
 # CONFIG_HW_RANDOM is not set
 # CONFIG_HWMON is not set
 CONFIG_MFD_T7L66XB=y
@@ -75,8 +68,6 @@ CONFIG_LCD_CLASS_DEVICE=y
 CONFIG_BACKLIGHT_CLASS_DEVICE=y
 # CONFIG_VGA_CONSOLE is not set
 CONFIG_FRAMEBUFFER_CONSOLE=y
-CONFIG_FONTS=y
-CONFIG_FONT_MINI_4x6=y
 CONFIG_SOUND=y
 CONFIG_SND=m
 CONFIG_SND_MIXER_OSS=m
@@ -96,10 +87,11 @@ CONFIG_VFAT_FS=y
 CONFIG_TMPFS=y
 CONFIG_NFS_FS=y
 CONFIG_NFS_V3=y
-CONFIG_PARTITION_ADVANCED=y
 CONFIG_NLS_CODEPAGE_437=y
 CONFIG_NLS_ISO8859_1=y
 # CONFIG_ENABLE_MUST_CHECK is not set
 CONFIG_CRYPTO_CBC=m
 CONFIG_CRYPTO_PCBC=m
 # CONFIG_CRYPTO_ANSI_CPRNG is not set
+CONFIG_FONTS=y
+CONFIG_FONT_MINI_4x6=y
diff --git a/arch/arm/configs/exynos_defconfig b/arch/arm/configs/exynos_defconfig
index cae09010a799..31e8e0c0ee1b 100644
--- a/arch/arm/configs/exynos_defconfig
+++ b/arch/arm/configs/exynos_defconfig
@@ -1,5 +1,5 @@
 CONFIG_SYSVIPC=y
-CONFIG_NO_HZ=y
+CONFIG_NO_HZ_IDLE=y
 CONFIG_HIGH_RES_TIMERS=y
 CONFIG_PREEMPT=y
 CONFIG_CGROUPS=y
@@ -13,12 +13,9 @@ CONFIG_BIG_LITTLE=y
 CONFIG_NR_CPUS=8
 CONFIG_HIGHMEM=y
 CONFIG_SECCOMP=y
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
 CONFIG_ARM_APPENDED_DTB=y
 CONFIG_ARM_ATAG_DTB_COMPAT=y
 CONFIG_CMDLINE="root=/dev/ram0 rw ramdisk=8192 initrd=0x41000000,8M console=ttySAC1,115200 init=/linuxrc mem=256M"
-CONFIG_ENERGY_MODEL=y
 CONFIG_CPU_FREQ=y
 CONFIG_CPU_FREQ_STAT=y
 CONFIG_CPU_FREQ_DEFAULT_GOV_ONDEMAND=y
@@ -34,7 +31,7 @@ CONFIG_NEON=y
 CONFIG_KERNEL_MODE_NEON=y
 CONFIG_PM_DEBUG=y
 CONFIG_PM_ADVANCED_DEBUG=y
-CONFIG_ARM_CRYPTO=y
+CONFIG_ENERGY_MODEL=y
 CONFIG_CRYPTO_SHA1_ARM_NEON=m
 CONFIG_CRYPTO_SHA256_ARM=m
 CONFIG_CRYPTO_SHA512_ARM=m
@@ -158,6 +155,7 @@ CONFIG_CHARGER_MAX14577=y
 CONFIG_CHARGER_MAX77693=y
 CONFIG_CHARGER_MAX8997=y
 CONFIG_CHARGER_MAX8998=y
+CONFIG_CHARGER_SMB347=y
 CONFIG_CHARGER_TPS65090=y
 CONFIG_SENSORS_LM90=y
 CONFIG_SENSORS_NTC_THERMISTOR=y
@@ -169,8 +167,6 @@ CONFIG_THERMAL_EMULATION=y
 CONFIG_WATCHDOG=y
 CONFIG_S3C2410_WATCHDOG=y
 CONFIG_MFD_CROS_EC_DEV=y
-CONFIG_CHROME_PLATFORMS=y
-CONFIG_CROS_EC=y
 CONFIG_MFD_MAX14577=y
 CONFIG_MFD_MAX77686=y
 CONFIG_MFD_MAX77693=y
@@ -206,19 +202,19 @@ CONFIG_MEDIA_PLATFORM_SUPPORT=y
 CONFIG_MEDIA_USB_SUPPORT=y
 CONFIG_USB_VIDEO_CLASS=m
 CONFIG_V4L_PLATFORM_DRIVERS=y
+CONFIG_V4L_MEM2MEM_DRIVERS=y
+CONFIG_VIDEO_SAMSUNG_EXYNOS_GSC=m
 CONFIG_VIDEO_SAMSUNG_EXYNOS4_IS=m
 CONFIG_VIDEO_S5P_FIMC=m
 CONFIG_VIDEO_S5P_MIPI_CSIS=m
 CONFIG_VIDEO_EXYNOS_FIMC_LITE=m
 CONFIG_VIDEO_EXYNOS4_FIMC_IS=m
-CONFIG_V4L_MEM2MEM_DRIVERS=y
 CONFIG_VIDEO_SAMSUNG_S5P_JPEG=m
 CONFIG_VIDEO_SAMSUNG_S5P_MFC=m
-CONFIG_VIDEO_SAMSUNG_EXYNOS_GSC=m
 CONFIG_V4L_TEST_DRIVERS=y
 CONFIG_VIDEO_VIVID=m
-CONFIG_VIDEO_S5K6A3=m
 CONFIG_VIDEO_S5C73M3=m
+CONFIG_VIDEO_S5K6A3=m
 CONFIG_DRM=y
 CONFIG_DRM_EXYNOS=y
 CONFIG_DRM_EXYNOS_FIMD=y
@@ -294,11 +290,11 @@ CONFIG_MMC_DW_EXYNOS=y
 CONFIG_NEW_LEDS=y
 CONFIG_LEDS_CLASS=y
 CONFIG_LEDS_CLASS_FLASH=y
-CONFIG_LEDS_AAT1290=y
 CONFIG_LEDS_GPIO=y
 CONFIG_LEDS_PWM=y
-CONFIG_LEDS_MAX77693=y
 CONFIG_LEDS_MAX8997=y
+CONFIG_LEDS_AAT1290=y
+CONFIG_LEDS_MAX77693=y
 CONFIG_LEDS_TRIGGER_HEARTBEAT=y
 CONFIG_RTC_CLASS=y
 CONFIG_RTC_DRV_MAX8998=y
@@ -308,6 +304,8 @@ CONFIG_RTC_DRV_S5M=y
 CONFIG_RTC_DRV_S3C=y
 CONFIG_DMADEVICES=y
 CONFIG_PL330_DMA=y
+CONFIG_CHROME_PLATFORMS=y
+CONFIG_CROS_EC=y
 CONFIG_CROS_EC_I2C=y
 CONFIG_CROS_EC_SPI=y
 CONFIG_COMMON_CLK_MAX77686=y
@@ -318,12 +316,12 @@ CONFIG_DEVFREQ_GOV_PERFORMANCE=y
 CONFIG_DEVFREQ_GOV_POWERSAVE=y
 CONFIG_DEVFREQ_GOV_USERSPACE=y
 CONFIG_ARM_EXYNOS_BUS_DEVFREQ=y
-CONFIG_EXYNOS5422_DMC=y
 CONFIG_DEVFREQ_EVENT_EXYNOS_NOCP=y
 CONFIG_EXTCON=y
 CONFIG_EXTCON_MAX14577=y
 CONFIG_EXTCON_MAX77693=y
 CONFIG_EXTCON_MAX8997=y
+CONFIG_EXYNOS5422_DMC=y
 CONFIG_IIO=y
 CONFIG_EXYNOS_ADC=y
 CONFIG_STMPE_ADC=y
@@ -375,10 +373,10 @@ CONFIG_FONTS=y
 CONFIG_FONT_7x14=y
 CONFIG_PRINTK_TIME=y
 CONFIG_DYNAMIC_DEBUG=y
-CONFIG_DEBUG_INFO=y
+CONFIG_DEBUG_KERNEL=y
+CONFIG_DEBUG_INFO_DWARF_TOOLCHAIN_DEFAULT=y
 CONFIG_MAGIC_SYSRQ=y
 CONFIG_DEBUG_FS=y
-CONFIG_DEBUG_KERNEL=y
 CONFIG_SOFTLOCKUP_DETECTOR=y
 # CONFIG_DETECT_HUNG_TASK is not set
 CONFIG_PROVE_LOCKING=y
diff --git a/arch/arm/configs/ezx_defconfig b/arch/arm/configs/ezx_defconfig
index a49e699e52de..ef7b0a0aee3a 100644
--- a/arch/arm/configs/ezx_defconfig
+++ b/arch/arm/configs/ezx_defconfig
@@ -1,27 +1,21 @@
 CONFIG_LOCALVERSION="-ezx200910312315"
 # CONFIG_LOCALVERSION_AUTO is not set
 CONFIG_SYSVIPC=y
+CONFIG_NO_HZ_IDLE=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_PREEMPT=y
 CONFIG_LOG_BUF_SHIFT=14
 CONFIG_SYSFS_DEPRECATED_V2=y
 CONFIG_BLK_DEV_INITRD=y
 CONFIG_RD_BZIP2=y
 CONFIG_RD_LZMA=y
 CONFIG_EXPERT=y
-# CONFIG_COMPAT_BRK is not set
-CONFIG_SLAB=y
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
-CONFIG_MODULE_FORCE_UNLOAD=y
-CONFIG_MODVERSIONS=y
 # CONFIG_BLK_DEV_BSG is not set
+# CONFIG_ARCH_MULTI_V7 is not set
 CONFIG_ARCH_PXA=y
 CONFIG_PXA_EZX=y
-CONFIG_NO_HZ=y
-CONFIG_HIGH_RES_TIMERS=y
-CONFIG_PREEMPT=y
 CONFIG_AEABI=y
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_UNUSED_BOARD_FILES=y
 CONFIG_CMDLINE="console=tty1 root=/dev/mmcblk0p2 rootfstype=ext2 rootdelay=3 ip=192.168.0.202:192.168.0.200:192.168.0.200:255.255.255.0 debug"
 CONFIG_KEXEC=y
 CONFIG_CPU_FREQ=y
@@ -31,10 +25,15 @@ CONFIG_CPU_FREQ_GOV_ONDEMAND=m
 CONFIG_CPU_FREQ_GOV_CONSERVATIVE=m
 CONFIG_CPU_IDLE=y
 CONFIG_FPE_NWFPE=y
-CONFIG_BINFMT_AOUT=m
-CONFIG_BINFMT_MISC=m
 CONFIG_PM=y
 CONFIG_APM_EMULATION=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_MODULE_FORCE_UNLOAD=y
+CONFIG_MODVERSIONS=y
+CONFIG_BINFMT_MISC=m
+CONFIG_SLAB=y
+# CONFIG_COMPAT_BRK is not set
 CONFIG_NET=y
 CONFIG_PACKET=y
 CONFIG_UNIX=y
@@ -71,6 +70,7 @@ CONFIG_NF_CONNTRACK_SANE=m
 CONFIG_NF_CONNTRACK_SIP=m
 CONFIG_NF_CONNTRACK_TFTP=m
 CONFIG_NF_CT_NETLINK=m
+CONFIG_NF_NAT=m
 CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m
 CONFIG_NETFILTER_XT_TARGET_LED=m
 CONFIG_NETFILTER_XT_TARGET_MARK=m
@@ -112,7 +112,6 @@ CONFIG_IP_NF_MATCH_TTL=m
 CONFIG_IP_NF_FILTER=m
 CONFIG_IP_NF_TARGET_REJECT=m
 CONFIG_IP_NF_TARGET_LOG=m
-CONFIG_NF_NAT=m
 CONFIG_IP_NF_TARGET_MASQUERADE=m
 CONFIG_IP_NF_TARGET_NETMAP=m
 CONFIG_IP_NF_TARGET_REDIRECT=m
@@ -178,15 +177,15 @@ CONFIG_BLK_DEV_NBD=m
 CONFIG_BLK_DEV_RAM=y
 CONFIG_NETDEVICES=y
 CONFIG_DUMMY=y
-# CONFIG_WLAN is not set
 CONFIG_PPP=m
-CONFIG_PPP_MULTILINK=y
+CONFIG_PPP_BSDCOMP=m
+CONFIG_PPP_DEFLATE=m
 CONFIG_PPP_FILTER=y
+CONFIG_PPP_MULTILINK=y
 CONFIG_PPP_ASYNC=m
 CONFIG_PPP_SYNC_TTY=m
-CONFIG_PPP_DEFLATE=m
-CONFIG_PPP_BSDCOMP=m
 # CONFIG_INPUT_MOUSEDEV is not set
+# CONFIG_WLAN is not set
 CONFIG_INPUT_EVDEV=y
 # CONFIG_KEYBOARD_ATKBD is not set
 CONFIG_KEYBOARD_GPIO=y
@@ -198,9 +197,9 @@ CONFIG_INPUT_MISC=y
 CONFIG_INPUT_UINPUT=y
 CONFIG_INPUT_PCAP=y
 # CONFIG_SERIO is not set
+CONFIG_LEGACY_PTY_COUNT=8
 CONFIG_SERIAL_PXA=y
 CONFIG_SERIAL_PXA_CONSOLE=y
-CONFIG_LEGACY_PTY_COUNT=8
 # CONFIG_HW_RANDOM is not set
 CONFIG_I2C=y
 CONFIG_I2C_CHARDEV=y
@@ -217,27 +216,27 @@ CONFIG_REGULATOR_PCAP=y
 CONFIG_MEDIA_SUPPORT=y
 CONFIG_VIDEO_DEV=y
 CONFIG_MEDIA_TUNER_CUSTOMISE=y
+CONFIG_RADIO_TEA5764=y
+# CONFIG_MEDIA_TUNER_MC44S803 is not set
+# CONFIG_MEDIA_TUNER_MT2060 is not set
+# CONFIG_MEDIA_TUNER_MT20XX is not set
+# CONFIG_MEDIA_TUNER_MT2131 is not set
+# CONFIG_MEDIA_TUNER_MT2266 is not set
+# CONFIG_MEDIA_TUNER_MXL5005S is not set
+# CONFIG_MEDIA_TUNER_MXL5007T is not set
+# CONFIG_MEDIA_TUNER_QT1010 is not set
 # CONFIG_MEDIA_TUNER_SIMPLE is not set
-# CONFIG_MEDIA_TUNER_TDA8290 is not set
-# CONFIG_MEDIA_TUNER_TDA827X is not set
 # CONFIG_MEDIA_TUNER_TDA18271 is not set
+# CONFIG_MEDIA_TUNER_TDA827X is not set
+# CONFIG_MEDIA_TUNER_TDA8290 is not set
 # CONFIG_MEDIA_TUNER_TDA9887 is not set
 # CONFIG_MEDIA_TUNER_TEA5761 is not set
 # CONFIG_MEDIA_TUNER_TEA5767 is not set
-# CONFIG_MEDIA_TUNER_MT20XX is not set
-# CONFIG_MEDIA_TUNER_MT2060 is not set
-# CONFIG_MEDIA_TUNER_MT2266 is not set
-# CONFIG_MEDIA_TUNER_MT2131 is not set
-# CONFIG_MEDIA_TUNER_QT1010 is not set
 # CONFIG_MEDIA_TUNER_XC2028 is not set
 # CONFIG_MEDIA_TUNER_XC5000 is not set
-# CONFIG_MEDIA_TUNER_MXL5005S is not set
-# CONFIG_MEDIA_TUNER_MXL5007T is not set
-# CONFIG_MEDIA_TUNER_MC44S803 is not set
 # CONFIG_VIDEO_HELPER_CHIPS_AUTO is not set
 CONFIG_VIDEO_PXA27x=y
 # CONFIG_V4L_USB_DRIVERS is not set
-CONFIG_RADIO_TEA5764=y
 CONFIG_FB=y
 CONFIG_FB_PXA=y
 CONFIG_FB_PXA_OVERLAY=y
@@ -247,8 +246,6 @@ CONFIG_BACKLIGHT_CLASS_DEVICE=y
 CONFIG_BACKLIGHT_PWM=y
 # CONFIG_VGA_CONSOLE is not set
 CONFIG_FRAMEBUFFER_CONSOLE=y
-CONFIG_FONTS=y
-CONFIG_FONT_MINI_4x6=y
 CONFIG_SOUND=y
 CONFIG_SND=y
 CONFIG_SND_MIXER_OSS=y
@@ -259,8 +256,8 @@ CONFIG_SND_PCM_OSS=y
 # CONFIG_SND_USB is not set
 CONFIG_SND_SOC=y
 CONFIG_SND_PXA2XX_SOC=y
-# CONFIG_USB_HID is not set
 CONFIG_HID_APPLE=m
+# CONFIG_USB_HID is not set
 CONFIG_USB=y
 CONFIG_USB_OHCI_HCD=y
 CONFIG_USB_GADGET=y
@@ -309,12 +306,10 @@ CONFIG_NFS_FS=y
 CONFIG_NFS_V3=y
 CONFIG_NFS_V3_ACL=y
 CONFIG_NFSD=m
-CONFIG_NFSD_V3=y
 CONFIG_NFSD_V3_ACL=y
 CONFIG_SMB_FS=m
 CONFIG_CIFS=m
 CONFIG_CIFS_STATS=y
-CONFIG_CIFS_WEAK_PW_HASH=y
 CONFIG_CIFS_XATTR=y
 CONFIG_CIFS_POSIX=y
 CONFIG_NLS_CODEPAGE_437=m
@@ -355,14 +350,8 @@ CONFIG_NLS_ISO8859_15=m
 CONFIG_NLS_KOI8_R=m
 CONFIG_NLS_KOI8_U=m
 CONFIG_NLS_UTF8=m
-CONFIG_PRINTK_TIME=y
-CONFIG_DEBUG_FS=y
 CONFIG_DEBUG_KERNEL=y
-# CONFIG_SCHED_DEBUG is not set
 CONFIG_DEBUG_RT_MUTEXES=y
-CONFIG_PROVE_LOCKING=y
-# CONFIG_FTRACE is not set
-CONFIG_DEBUG_USER=y
 CONFIG_CRYPTO_NULL=m
 CONFIG_CRYPTO_CRYPTD=m
 CONFIG_CRYPTO_TEST=m
@@ -390,3 +379,11 @@ CONFIG_CRYPTO_SERPENT=m
 CONFIG_CRYPTO_TEA=m
 CONFIG_CRYPTO_TWOFISH=m
 # CONFIG_CRYPTO_ANSI_CPRNG is not set
+CONFIG_FONTS=y
+CONFIG_FONT_MINI_4x6=y
+CONFIG_PRINTK_TIME=y
+CONFIG_DEBUG_FS=y
+# CONFIG_SCHED_DEBUG is not set
+CONFIG_PROVE_LOCKING=y
+# CONFIG_FTRACE is not set
+CONFIG_DEBUG_USER=y
diff --git a/arch/arm/configs/footbridge_defconfig b/arch/arm/configs/footbridge_defconfig
index 7a32de51f0fa..87c489337d0e 100644
--- a/arch/arm/configs/footbridge_defconfig
+++ b/arch/arm/configs/footbridge_defconfig
@@ -4,18 +4,17 @@ CONFIG_LOG_BUF_SHIFT=14
 CONFIG_BLK_DEV_INITRD=y
 CONFIG_EXPERT=y
 # CONFIG_HOTPLUG is not set
-CONFIG_MODULES=y
+CONFIG_ARCH_MULTI_V4=y
+# CONFIG_ARCH_MULTI_V7 is not set
 CONFIG_ARCH_FOOTBRIDGE=y
-CONFIG_ARCH_CATS=y
 CONFIG_ARCH_EBSA285_HOST=y
 CONFIG_ARCH_NETWINDER=y
-CONFIG_LEDS=y
-CONFIG_LEDS_TIMER=y
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
 CONFIG_FPE_NWFPE=y
 CONFIG_FPE_NWFPE_XP=y
-CONFIG_BINFMT_AOUT=y
+CONFIG_MODULES=y
+CONFIG_PARTITION_ADVANCED=y
+CONFIG_ACORN_PARTITION=y
+CONFIG_ACORN_PARTITION_ADFS=y
 CONFIG_NET=y
 CONFIG_PACKET=y
 CONFIG_UNIX=y
@@ -26,15 +25,6 @@ CONFIG_IP_PNP_BOOTP=y
 CONFIG_SYN_COOKIES=y
 # CONFIG_IPV6 is not set
 CONFIG_ATM=y
-CONFIG_IRDA=m
-CONFIG_IRLAN=m
-CONFIG_IRNET=m
-CONFIG_IRCOMM=m
-CONFIG_IRDA_ULTRA=y
-CONFIG_IRDA_CACHE_LAST_LSAP=y
-CONFIG_IRDA_FAST_RR=y
-CONFIG_IRDA_DEBUG=y
-CONFIG_WINBOND_FIR=m
 CONFIG_PARPORT=y
 CONFIG_PARPORT_PC=y
 CONFIG_PARPORT_PC_FIFO=y
@@ -71,17 +61,17 @@ CONFIG_VORTEX=y
 CONFIG_NET_PCI=y
 CONFIG_NE2K_PCI=y
 CONFIG_PPP=m
-CONFIG_PPP_ASYNC=m
-CONFIG_PPP_DEFLATE=m
 CONFIG_PPP_BSDCOMP=m
+CONFIG_PPP_DEFLATE=m
 CONFIG_PPPOE=m
+CONFIG_PPP_ASYNC=m
 CONFIG_SLIP=m
 CONFIG_SLIP_COMPRESSED=y
 CONFIG_SLIP_SMART=y
 CONFIG_SLIP_MODE_SLIP6=y
-CONFIG_SERIAL_NONSTANDARD=y
 CONFIG_SERIAL_21285=y
 CONFIG_SERIAL_21285_CONSOLE=y
+CONFIG_SERIAL_NONSTANDARD=y
 CONFIG_PRINTER=m
 CONFIG_DS1620=y
 CONFIG_NWBUTTON=y
@@ -99,6 +89,10 @@ CONFIG_SOUND=m
 CONFIG_USB=m
 CONFIG_USB_MON=m
 CONFIG_USB_PRINTER=m
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=y
+CONFIG_LEDS_TRIGGERS=y
+CONFIG_LEDS_TRIGGER_TIMER=y
 CONFIG_EXT2_FS=y
 CONFIG_AUTOFS4_FS=y
 CONFIG_ISO9660_FS=m
@@ -109,9 +103,6 @@ CONFIG_ADFS_FS=m
 CONFIG_NFS_FS=y
 CONFIG_ROOT_NFS=y
 CONFIG_NFSD=m
-CONFIG_PARTITION_ADVANCED=y
-CONFIG_ACORN_PARTITION=y
-CONFIG_ACORN_PARTITION_ADFS=y
 CONFIG_NLS=y
 CONFIG_NLS_CODEPAGE_437=m
 CONFIG_NLS_CODEPAGE_850=m
diff --git a/arch/arm/configs/gemini_defconfig b/arch/arm/configs/gemini_defconfig
index e6ff844821cf..a80bc8a43091 100644
--- a/arch/arm/configs/gemini_defconfig
+++ b/arch/arm/configs/gemini_defconfig
@@ -49,11 +49,13 @@ CONFIG_ATA=y
 CONFIG_PATA_FTIDE010=y
 CONFIG_NETDEVICES=y
 CONFIG_TUN=y
+CONFIG_NET_DSA_REALTEK=y
 CONFIG_NET_DSA_REALTEK_SMI=y
+CONFIG_NET_DSA_REALTEK_RTL8366RB=y
 CONFIG_GEMINI_ETHERNET=y
+CONFIG_MARVELL_PHY=y
 CONFIG_MDIO_BITBANG=y
 CONFIG_MDIO_GPIO=y
-CONFIG_MARVELL_PHY=y
 CONFIG_INPUT_EVDEV=y
 CONFIG_KEYBOARD_GPIO=y
 # CONFIG_INPUT_MOUSE is not set
@@ -63,10 +65,10 @@ CONFIG_SERIAL_8250_CONSOLE=y
 CONFIG_SERIAL_8250_NR_UARTS=1
 CONFIG_SERIAL_8250_RUNTIME_UARTS=1
 CONFIG_SERIAL_OF_PLATFORM=y
-# CONFIG_HW_RANDOM is not set
 CONFIG_I2C_GPIO=y
 CONFIG_SPI=y
 CONFIG_SPI_GPIO=y
+CONFIG_SENSORS_DRIVETEMP=y
 CONFIG_SENSORS_GPIO_FAN=y
 CONFIG_SENSORS_LM75=y
 CONFIG_THERMAL=y
@@ -99,5 +101,5 @@ CONFIG_TMPFS_POSIX_ACL=y
 CONFIG_ROMFS_FS=y
 CONFIG_NLS_CODEPAGE_437=y
 CONFIG_NLS_ISO8859_1=y
-# CONFIG_ENABLE_MUST_CHECK is not set
+CONFIG_CRYPTO_DEV_SL3516=y
 CONFIG_DEBUG_FS=y
diff --git a/arch/arm/configs/h3600_defconfig b/arch/arm/configs/h3600_defconfig
index c02b3e409610..4e272875c797 100644
--- a/arch/arm/configs/h3600_defconfig
+++ b/arch/arm/configs/h3600_defconfig
@@ -1,28 +1,23 @@
 CONFIG_SYSVIPC=y
 CONFIG_NO_HZ_IDLE=y
 CONFIG_HIGH_RES_TIMERS=y
+CONFIG_PREEMPT=y
 CONFIG_LOG_BUF_SHIFT=14
 CONFIG_BLK_DEV_INITRD=y
-CONFIG_MODULES=y
-# CONFIG_BLK_DEV_BSG is not set
+CONFIG_ARCH_MULTI_V4=y
+# CONFIG_ARCH_MULTI_V7 is not set
 CONFIG_ARCH_SA1100=y
 CONFIG_SA1100_H3600=y
-CONFIG_PCCARD=y
-CONFIG_PCMCIA_SA1100=y
-CONFIG_PREEMPT=y
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
 # CONFIG_CPU_FREQ_STAT is not set
 CONFIG_FPE_NWFPE=y
+CONFIG_MODULES=y
 CONFIG_NET=y
 CONFIG_UNIX=y
 CONFIG_INET=y
 # CONFIG_IPV6 is not set
-CONFIG_IRDA=m
-CONFIG_IRLAN=m
-CONFIG_IRNET=m
-CONFIG_IRCOMM=m
 # CONFIG_WIRELESS is not set
+CONFIG_PCCARD=y
+CONFIG_PCMCIA_SA1100=y
 CONFIG_MTD=y
 CONFIG_MTD_REDBOOT_PARTS=y
 CONFIG_MTD_BLOCK=y
@@ -36,6 +31,7 @@ CONFIG_BLK_DEV_LOOP=m
 CONFIG_BLK_DEV_RAM=y
 CONFIG_BLK_DEV_RAM_SIZE=8192
 CONFIG_BLK_DEV_SD=y
+# CONFIG_BLK_DEV_BSG is not set
 CONFIG_ATA=y
 CONFIG_PATA_PCMCIA=y
 CONFIG_NETDEVICES=y
diff --git a/arch/arm/configs/h5000_defconfig b/arch/arm/configs/h5000_defconfig
index f5a338fefda8..d01f1a6bd04d 100644
--- a/arch/arm/configs/h5000_defconfig
+++ b/arch/arm/configs/h5000_defconfig
@@ -5,21 +5,21 @@ CONFIG_LOG_BUF_SHIFT=16
 # CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
 CONFIG_EXPERT=y
 # CONFIG_UID16 is not set
-CONFIG_SLAB=y
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
-CONFIG_MODULE_FORCE_UNLOAD=y
 # CONFIG_BLK_DEV_BSG is not set
+# CONFIG_ARCH_MULTI_V7 is not set
 CONFIG_ARCH_PXA=y
 CONFIG_MACH_H5000=y
 CONFIG_AEABI=y
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_UNUSED_BOARD_FILES=y
 CONFIG_CMDLINE="keepinitrd"
 CONFIG_KEXEC=y
 CONFIG_FPE_NWFPE=y
 CONFIG_PM=y
 CONFIG_APM_EMULATION=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_MODULE_FORCE_UNLOAD=y
+CONFIG_SLAB=y
 CONFIG_NET=y
 CONFIG_PACKET=y
 CONFIG_UNIX=y
@@ -42,9 +42,9 @@ CONFIG_MTD_PHYSMAP=y
 # CONFIG_INPUT_KEYBOARD is not set
 # CONFIG_INPUT_MOUSE is not set
 # CONFIG_SERIO is not set
+CONFIG_LEGACY_PTY_COUNT=32
 CONFIG_SERIAL_PXA=y
 CONFIG_SERIAL_PXA_CONSOLE=y
-CONFIG_LEGACY_PTY_COUNT=32
 # CONFIG_HW_RANDOM is not set
 # CONFIG_HWMON is not set
 # CONFIG_VGA_CONSOLE is not set
@@ -59,11 +59,7 @@ CONFIG_TMPFS=y
 CONFIG_JFFS2_FS=y
 CONFIG_JFFS2_COMPRESSION_OPTIONS=y
 # CONFIG_NETWORK_FILESYSTEMS is not set
-CONFIG_PRINTK_TIME=y
 CONFIG_DEBUG_KERNEL=y
-# CONFIG_SCHED_DEBUG is not set
-# CONFIG_DEBUG_BUGVERBOSE is not set
-# CONFIG_FTRACE is not set
 CONFIG_CRYPTO=y
 CONFIG_CRYPTO_HMAC=y
 CONFIG_CRYPTO_MD5=y
@@ -72,3 +68,7 @@ CONFIG_CRYPTO_DES=y
 CONFIG_CRYPTO_DEFLATE=y
 # CONFIG_CRYPTO_HW is not set
 CONFIG_CRC_CCITT=y
+CONFIG_PRINTK_TIME=y
+# CONFIG_DEBUG_BUGVERBOSE is not set
+# CONFIG_SCHED_DEBUG is not set
+# CONFIG_FTRACE is not set
diff --git a/arch/arm/configs/hackkit_defconfig b/arch/arm/configs/hackkit_defconfig
index 742d18cdabde..3c91a851fd08 100644
--- a/arch/arm/configs/hackkit_defconfig
+++ b/arch/arm/configs/hackkit_defconfig
@@ -1,17 +1,15 @@
 CONFIG_SYSVIPC=y
 CONFIG_LOG_BUF_SHIFT=14
 CONFIG_BLK_DEV_INITRD=y
-CONFIG_MODULES=y
+CONFIG_ARCH_MULTI_V4=y
+# CONFIG_ARCH_MULTI_V7 is not set
 CONFIG_ARCH_SA1100=y
 CONFIG_SA1100_HACKKIT=y
-CONFIG_LEDS=y
-CONFIG_LEDS_CPU=y
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_UNUSED_BOARD_FILES=y
 CONFIG_CMDLINE="console=ttySA0,115200 root=/dev/ram0 initrd=0xc0400000,8M init=/rootshell"
 CONFIG_CPU_FREQ_GOV_PERFORMANCE=y
 CONFIG_FPE_NWFPE=y
-CONFIG_BINFMT_AOUT=y
+CONFIG_MODULES=y
 CONFIG_NET=y
 CONFIG_PACKET=y
 CONFIG_UNIX=y
@@ -33,13 +31,17 @@ CONFIG_DUMMY=y
 CONFIG_SERIAL_SA1100=y
 CONFIG_SERIAL_SA1100_CONSOLE=y
 # CONFIG_VGA_CONSOLE is not set
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=y
+CONFIG_LEDS_TRIGGERS=y
+CONFIG_LEDS_TRIGGER_CPU=y
 CONFIG_EXT2_FS=y
 CONFIG_MSDOS_FS=y
 CONFIG_VFAT_FS=y
 CONFIG_TMPFS=y
 CONFIG_CRAMFS=y
-CONFIG_MAGIC_SYSRQ=y
 CONFIG_DEBUG_KERNEL=y
+CONFIG_MAGIC_SYSRQ=y
 CONFIG_DEBUG_SPINLOCK=y
 CONFIG_DEBUG_USER=y
 CONFIG_DEBUG_LL=y
diff --git a/arch/arm/configs/hisi_defconfig b/arch/arm/configs/hisi_defconfig
index 74d611e41e02..0376a65e8bc1 100644
--- a/arch/arm/configs/hisi_defconfig
+++ b/arch/arm/configs/hisi_defconfig
@@ -1,24 +1,25 @@
-CONFIG_NO_HZ=y
+CONFIG_NO_HZ_IDLE=y
 CONFIG_HIGH_RES_TIMERS=y
+CONFIG_PREEMPT=y
 CONFIG_BLK_DEV_INITRD=y
 CONFIG_RD_LZMA=y
 CONFIG_ARCH_HISI=y
 CONFIG_ARCH_HI3xxx=y
-CONFIG_PARTITION_ADVANCED=y
-CONFIG_CMDLINE_PARTITION=y
-CONFIG_ARCH_HIX5HD2=y
 CONFIG_ARCH_HIP01=y
 CONFIG_ARCH_HIP04=y
+CONFIG_ARCH_HIX5HD2=y
 CONFIG_SMP=y
 CONFIG_NR_CPUS=16
-CONFIG_PREEMPT=y
 CONFIG_AEABI=y
 CONFIG_HIGHMEM=y
 CONFIG_ARM_APPENDED_DTB=y
 CONFIG_ARM_ATAG_DTB_COMPAT=y
+CONFIG_VFP=y
 CONFIG_NEON=y
 CONFIG_ARM_ATAG_DTB_COMPAT_CMDLINE_FROM_BOOTLOADER=y
 CONFIG_PM=y
+CONFIG_PARTITION_ADVANCED=y
+CONFIG_CMDLINE_PARTITION=y
 CONFIG_NET=y
 CONFIG_PACKET=y
 CONFIG_UNIX=y
@@ -39,20 +40,20 @@ CONFIG_SERIAL_8250_CONSOLE=y
 CONFIG_SERIAL_8250_NR_UARTS=2
 CONFIG_SERIAL_8250_RUNTIME_UARTS=2
 CONFIG_SERIAL_8250_DW=y
+CONFIG_SERIAL_OF_PLATFORM=y
 CONFIG_SERIAL_AMBA_PL011=y
 CONFIG_SERIAL_AMBA_PL011_CONSOLE=y
-CONFIG_SERIAL_OF_PLATFORM=y
 CONFIG_I2C_DESIGNWARE_PLATFORM=y
 CONFIG_SPI=y
 CONFIG_SPI_PL022=y
 CONFIG_PINCTRL_SINGLE=y
-CONFIG_DEBUG_GPIO=y
 CONFIG_GPIO_SYSFS=y
 CONFIG_GPIOLIB=y
-CONFIG_GPIO_GENERIC_PLATFORM=y
 CONFIG_REGULATOR_GPIO=y
+CONFIG_DEBUG_GPIO=y
 CONFIG_GPIO_DWAPB=y
 CONFIG_MFD_SYSCON=y
+CONFIG_GPIO_GENERIC_PLATFORM=y
 CONFIG_POWER_RESET_SYSCON=y
 CONFIG_DRM=y
 CONFIG_FB_SIMPLE=y
@@ -66,13 +67,13 @@ CONFIG_USB_OHCI_HCD_PLATFORM=y
 CONFIG_USB_STORAGE=y
 CONFIG_NOP_USB_XCEIV=y
 CONFIG_MMC=y
-CONFIG_RTC_CLASS=y
 CONFIG_MMC_DW=y
 CONFIG_MMC_DW_PLTFM=y
+CONFIG_RTC_CLASS=y
 CONFIG_RTC_DRV_PL031=y
 CONFIG_DMADEVICES=y
-CONFIG_DW_DMAC=y
 CONFIG_PL330_DMA=y
+CONFIG_DW_DMAC=y
 CONFIG_PWM=y
 CONFIG_PHY_HIX5HD2_SATA=y
 CONFIG_EXT4_FS=y
@@ -81,11 +82,10 @@ CONFIG_NFS_FS=y
 CONFIG_NFS_V3_ACL=y
 CONFIG_NFS_V4=y
 CONFIG_ROOT_NFS=y
-CONFIG_PRINTK_TIME=y
-CONFIG_DEBUG_FS=y
 CONFIG_NLS_CODEPAGE_437=y
 CONFIG_NLS_ISO8859_1=y
+CONFIG_PRINTK_TIME=y
 CONFIG_DEBUG_KERNEL=y
 CONFIG_LOCKUP_DETECTOR=y
-CONFIG_VFP=y
 CONFIG_VFPv3=y
+CONFIG_DEBUG_FS=y
diff --git a/arch/arm/configs/imote2_defconfig b/arch/arm/configs/imote2_defconfig
deleted file mode 100644
index 118c4c927f26..000000000000
--- a/arch/arm/configs/imote2_defconfig
+++ /dev/null
@@ -1,367 +0,0 @@
-# CONFIG_LOCALVERSION_AUTO is not set
-CONFIG_SYSVIPC=y
-CONFIG_LOG_BUF_SHIFT=14
-CONFIG_SYSFS_DEPRECATED_V2=y
-CONFIG_BLK_DEV_INITRD=y
-CONFIG_RD_BZIP2=y
-CONFIG_RD_LZMA=y
-CONFIG_EXPERT=y
-# CONFIG_COMPAT_BRK is not set
-CONFIG_SLAB=y
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
-CONFIG_MODULE_FORCE_UNLOAD=y
-CONFIG_MODVERSIONS=y
-# CONFIG_BLK_DEV_BSG is not set
-CONFIG_ARCH_PXA=y
-CONFIG_MACH_INTELMOTE2=y
-CONFIG_NO_HZ=y
-CONFIG_HIGH_RES_TIMERS=y
-CONFIG_PREEMPT=y
-CONFIG_AEABI=y
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
-CONFIG_CMDLINE="root=/dev/mtdblock2 rootfstype=jffs2 console=ttyS2,115200 mem=32M"
-CONFIG_KEXEC=y
-CONFIG_FPE_NWFPE=y
-CONFIG_BINFMT_AOUT=m
-CONFIG_BINFMT_MISC=m
-CONFIG_PM=y
-CONFIG_APM_EMULATION=y
-CONFIG_NET=y
-CONFIG_PACKET=y
-CONFIG_UNIX=y
-CONFIG_INET=y
-CONFIG_IP_PNP=y
-CONFIG_IP_PNP_DHCP=y
-CONFIG_IP_PNP_BOOTP=y
-CONFIG_IP_PNP_RARP=y
-CONFIG_SYN_COOKIES=y
-# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
-# CONFIG_INET_XFRM_MODE_TUNNEL is not set
-# CONFIG_INET_XFRM_MODE_BEET is not set
-# CONFIG_INET_DIAG is not set
-CONFIG_INET6_AH=m
-CONFIG_INET6_ESP=m
-CONFIG_INET6_IPCOMP=m
-CONFIG_IPV6_MIP6=m
-CONFIG_IPV6_TUNNEL=m
-CONFIG_IPV6_MULTIPLE_TABLES=y
-CONFIG_IPV6_SUBTREES=y
-CONFIG_NETFILTER=y
-CONFIG_NETFILTER_NETLINK_QUEUE=m
-CONFIG_NF_CONNTRACK=m
-CONFIG_NF_CONNTRACK_EVENTS=y
-CONFIG_NF_CT_PROTO_SCTP=y
-CONFIG_NF_CT_PROTO_UDPLITE=y
-CONFIG_NF_CONNTRACK_AMANDA=m
-CONFIG_NF_CONNTRACK_FTP=m
-CONFIG_NF_CONNTRACK_H323=m
-CONFIG_NF_CONNTRACK_IRC=m
-CONFIG_NF_CONNTRACK_NETBIOS_NS=m
-CONFIG_NF_CONNTRACK_PPTP=m
-CONFIG_NF_CONNTRACK_SANE=m
-CONFIG_NF_CONNTRACK_SIP=m
-CONFIG_NF_CONNTRACK_TFTP=m
-CONFIG_NF_CT_NETLINK=m
-CONFIG_NETFILTER_XT_TARGET_CLASSIFY=m
-CONFIG_NETFILTER_XT_TARGET_LED=m
-CONFIG_NETFILTER_XT_TARGET_MARK=m
-CONFIG_NETFILTER_XT_TARGET_NFLOG=m
-CONFIG_NETFILTER_XT_TARGET_NFQUEUE=m
-CONFIG_NETFILTER_XT_TARGET_TCPMSS=m
-CONFIG_NETFILTER_XT_MATCH_COMMENT=m
-CONFIG_NETFILTER_XT_MATCH_CONNBYTES=m
-CONFIG_NETFILTER_XT_MATCH_CONNLIMIT=m
-CONFIG_NETFILTER_XT_MATCH_CONNMARK=m
-CONFIG_NETFILTER_XT_MATCH_CONNTRACK=m
-CONFIG_NETFILTER_XT_MATCH_DCCP=m
-CONFIG_NETFILTER_XT_MATCH_DSCP=m
-CONFIG_NETFILTER_XT_MATCH_ESP=m
-CONFIG_NETFILTER_XT_MATCH_HASHLIMIT=m
-CONFIG_NETFILTER_XT_MATCH_HELPER=m
-CONFIG_NETFILTER_XT_MATCH_LENGTH=m
-CONFIG_NETFILTER_XT_MATCH_LIMIT=m
-CONFIG_NETFILTER_XT_MATCH_MAC=m
-CONFIG_NETFILTER_XT_MATCH_MARK=m
-CONFIG_NETFILTER_XT_MATCH_MULTIPORT=m
-CONFIG_NETFILTER_XT_MATCH_POLICY=m
-CONFIG_NETFILTER_XT_MATCH_PKTTYPE=m
-CONFIG_NETFILTER_XT_MATCH_QUOTA=m
-CONFIG_NETFILTER_XT_MATCH_REALM=m
-CONFIG_NETFILTER_XT_MATCH_SCTP=m
-CONFIG_NETFILTER_XT_MATCH_STATE=m
-CONFIG_NETFILTER_XT_MATCH_STATISTIC=m
-CONFIG_NETFILTER_XT_MATCH_STRING=m
-CONFIG_NETFILTER_XT_MATCH_TCPMSS=m
-CONFIG_NETFILTER_XT_MATCH_TIME=m
-CONFIG_NETFILTER_XT_MATCH_U32=m
-CONFIG_NF_CONNTRACK_IPV4=m
-CONFIG_IP_NF_IPTABLES=m
-CONFIG_IP_NF_MATCH_ADDRTYPE=m
-CONFIG_IP_NF_MATCH_AH=m
-CONFIG_IP_NF_MATCH_ECN=m
-CONFIG_IP_NF_MATCH_TTL=m
-CONFIG_IP_NF_FILTER=m
-CONFIG_IP_NF_TARGET_REJECT=m
-CONFIG_IP_NF_TARGET_LOG=m
-CONFIG_NF_NAT=m
-CONFIG_IP_NF_TARGET_MASQUERADE=m
-CONFIG_IP_NF_TARGET_NETMAP=m
-CONFIG_IP_NF_TARGET_REDIRECT=m
-CONFIG_NF_NAT_SNMP_BASIC=m
-CONFIG_IP_NF_MANGLE=m
-CONFIG_IP_NF_TARGET_CLUSTERIP=m
-CONFIG_IP_NF_TARGET_ECN=m
-CONFIG_IP_NF_TARGET_TTL=m
-CONFIG_IP_NF_RAW=m
-CONFIG_IP_NF_ARPTABLES=m
-CONFIG_IP_NF_ARPFILTER=m
-CONFIG_IP_NF_ARP_MANGLE=m
-CONFIG_NF_CONNTRACK_IPV6=m
-CONFIG_IP6_NF_IPTABLES=m
-CONFIG_IP6_NF_MATCH_AH=m
-CONFIG_IP6_NF_MATCH_EUI64=m
-CONFIG_IP6_NF_MATCH_FRAG=m
-CONFIG_IP6_NF_MATCH_OPTS=m
-CONFIG_IP6_NF_MATCH_HL=m
-CONFIG_IP6_NF_MATCH_IPV6HEADER=m
-CONFIG_IP6_NF_MATCH_MH=m
-CONFIG_IP6_NF_MATCH_RT=m
-CONFIG_IP6_NF_TARGET_HL=m
-CONFIG_IP6_NF_FILTER=m
-CONFIG_IP6_NF_TARGET_REJECT=m
-CONFIG_IP6_NF_MANGLE=m
-CONFIG_IP6_NF_RAW=m
-CONFIG_BRIDGE=m
-# CONFIG_BRIDGE_IGMP_SNOOPING is not set
-CONFIG_IEEE802154=y
-# CONFIG_WIRELESS is not set
-CONFIG_DEVTMPFS=y
-CONFIG_DEVTMPFS_MOUNT=y
-CONFIG_FW_LOADER=m
-CONFIG_CONNECTOR=m
-CONFIG_MTD=y
-CONFIG_MTD_CMDLINE_PARTS=y
-CONFIG_MTD_AFS_PARTS=y
-CONFIG_MTD_AR7_PARTS=y
-CONFIG_MTD_BLOCK=y
-CONFIG_MTD_CFI=y
-CONFIG_MTD_CFI_ADV_OPTIONS=y
-CONFIG_MTD_CFI_GEOMETRY=y
-# CONFIG_MTD_MAP_BANK_WIDTH_1 is not set
-# CONFIG_MTD_MAP_BANK_WIDTH_4 is not set
-# CONFIG_MTD_CFI_I2 is not set
-CONFIG_MTD_OTP=y
-CONFIG_MTD_CFI_INTELEXT=y
-CONFIG_MTD_PXA2XX=y
-CONFIG_BLK_DEV_LOOP=m
-CONFIG_BLK_DEV_CRYPTOLOOP=m
-CONFIG_BLK_DEV_NBD=m
-CONFIG_BLK_DEV_RAM=y
-CONFIG_NETDEVICES=y
-CONFIG_DUMMY=y
-# CONFIG_WLAN is not set
-CONFIG_PPP=m
-CONFIG_PPP_MULTILINK=y
-CONFIG_PPP_FILTER=y
-CONFIG_PPP_ASYNC=m
-CONFIG_PPP_SYNC_TTY=m
-CONFIG_PPP_DEFLATE=m
-CONFIG_PPP_BSDCOMP=m
-# CONFIG_INPUT_MOUSEDEV is not set
-CONFIG_INPUT_EVDEV=y
-# CONFIG_KEYBOARD_ATKBD is not set
-CONFIG_KEYBOARD_GPIO=y
-CONFIG_KEYBOARD_PXA27x=y
-# CONFIG_INPUT_MOUSE is not set
-CONFIG_INPUT_TOUCHSCREEN=y
-CONFIG_INPUT_MISC=y
-CONFIG_INPUT_UINPUT=y
-# CONFIG_SERIO is not set
-CONFIG_SERIAL_PXA=y
-CONFIG_SERIAL_PXA_CONSOLE=y
-CONFIG_LEGACY_PTY_COUNT=8
-# CONFIG_HW_RANDOM is not set
-CONFIG_I2C=y
-CONFIG_I2C_CHARDEV=y
-CONFIG_I2C_PXA=y
-CONFIG_SPI=y
-CONFIG_SPI_PXA2XX=y
-CONFIG_GPIO_SYSFS=y
-CONFIG_POWER_SUPPLY=y
-# CONFIG_HWMON is not set
-CONFIG_PMIC_DA903X=y
-CONFIG_REGULATOR=y
-CONFIG_REGULATOR_DEBUG=y
-CONFIG_REGULATOR_DA903X=y
-CONFIG_MEDIA_SUPPORT=y
-CONFIG_VIDEO_DEV=y
-CONFIG_MEDIA_TUNER_CUSTOMISE=y
-# CONFIG_MEDIA_TUNER_SIMPLE is not set
-# CONFIG_MEDIA_TUNER_TDA8290 is not set
-# CONFIG_MEDIA_TUNER_TDA827X is not set
-# CONFIG_MEDIA_TUNER_TDA18271 is not set
-# CONFIG_MEDIA_TUNER_TDA9887 is not set
-# CONFIG_MEDIA_TUNER_TEA5761 is not set
-# CONFIG_MEDIA_TUNER_TEA5767 is not set
-# CONFIG_MEDIA_TUNER_MT20XX is not set
-# CONFIG_MEDIA_TUNER_MT2060 is not set
-# CONFIG_MEDIA_TUNER_MT2266 is not set
-# CONFIG_MEDIA_TUNER_MT2131 is not set
-# CONFIG_MEDIA_TUNER_QT1010 is not set
-# CONFIG_MEDIA_TUNER_XC2028 is not set
-# CONFIG_MEDIA_TUNER_XC5000 is not set
-# CONFIG_MEDIA_TUNER_MXL5005S is not set
-# CONFIG_MEDIA_TUNER_MXL5007T is not set
-# CONFIG_MEDIA_TUNER_MC44S803 is not set
-# CONFIG_VIDEO_HELPER_CHIPS_AUTO is not set
-CONFIG_VIDEO_PXA27x=y
-# CONFIG_V4L_USB_DRIVERS is not set
-# CONFIG_RADIO_ADAPTERS is not set
-CONFIG_FB=y
-CONFIG_FB_PXA=y
-CONFIG_FB_PXA_OVERLAY=y
-CONFIG_FB_PXA_PARAMETERS=y
-# CONFIG_LCD_CLASS_DEVICE is not set
-CONFIG_BACKLIGHT_CLASS_DEVICE=y
-# CONFIG_VGA_CONSOLE is not set
-CONFIG_FRAMEBUFFER_CONSOLE=y
-CONFIG_FONTS=y
-CONFIG_FONT_MINI_4x6=y
-CONFIG_SOUND=y
-CONFIG_SND=y
-CONFIG_SND_MIXER_OSS=y
-CONFIG_SND_PCM_OSS=y
-# CONFIG_SND_DRIVERS is not set
-# CONFIG_SND_ARM is not set
-# CONFIG_SND_SPI is not set
-# CONFIG_SND_USB is not set
-CONFIG_SND_SOC=y
-CONFIG_SND_PXA2XX_SOC=y
-# CONFIG_USB_HID is not set
-CONFIG_USB=y
-CONFIG_USB_OHCI_HCD=y
-CONFIG_USB_GADGET=y
-CONFIG_USB_PXA27X=y
-CONFIG_USB_ETH=m
-# CONFIG_USB_ETH_RNDIS is not set
-CONFIG_MMC=y
-CONFIG_SDIO_UART=m
-CONFIG_MMC_PXA=y
-CONFIG_MMC_SPI=y
-CONFIG_NEW_LEDS=y
-CONFIG_LEDS_CLASS=y
-CONFIG_LEDS_LP3944=y
-CONFIG_LEDS_TRIGGERS=y
-CONFIG_LEDS_TRIGGER_TIMER=y
-CONFIG_LEDS_TRIGGER_HEARTBEAT=y
-CONFIG_LEDS_TRIGGER_BACKLIGHT=y
-CONFIG_LEDS_TRIGGER_GPIO=y
-CONFIG_LEDS_TRIGGER_DEFAULT_ON=y
-CONFIG_RTC_CLASS=y
-CONFIG_RTC_DRV_PXA=y
-CONFIG_EXT2_FS=y
-CONFIG_EXT3_FS=m
-CONFIG_AUTOFS4_FS=y
-CONFIG_FUSE_FS=m
-CONFIG_CUSE=m
-CONFIG_MSDOS_FS=m
-CONFIG_VFAT_FS=m
-CONFIG_TMPFS=y
-CONFIG_JFFS2_FS=y
-CONFIG_JFFS2_FS_WBUF_VERIFY=y
-CONFIG_JFFS2_SUMMARY=y
-CONFIG_JFFS2_FS_XATTR=y
-CONFIG_JFFS2_COMPRESSION_OPTIONS=y
-CONFIG_JFFS2_LZO=y
-CONFIG_JFFS2_RUBIN=y
-CONFIG_CRAMFS=m
-CONFIG_SQUASHFS=m
-CONFIG_ROMFS_FS=m
-CONFIG_NFS_FS=y
-CONFIG_NFS_V3=y
-CONFIG_NFS_V3_ACL=y
-CONFIG_NFSD=m
-CONFIG_NFSD_V3=y
-CONFIG_NFSD_V3_ACL=y
-CONFIG_SMB_FS=m
-CONFIG_CIFS=m
-CONFIG_CIFS_STATS=y
-CONFIG_CIFS_WEAK_PW_HASH=y
-CONFIG_CIFS_XATTR=y
-CONFIG_CIFS_POSIX=y
-CONFIG_NLS_CODEPAGE_437=m
-CONFIG_NLS_CODEPAGE_737=m
-CONFIG_NLS_CODEPAGE_775=m
-CONFIG_NLS_CODEPAGE_850=m
-CONFIG_NLS_CODEPAGE_852=m
-CONFIG_NLS_CODEPAGE_855=m
-CONFIG_NLS_CODEPAGE_857=m
-CONFIG_NLS_CODEPAGE_860=m
-CONFIG_NLS_CODEPAGE_861=m
-CONFIG_NLS_CODEPAGE_862=m
-CONFIG_NLS_CODEPAGE_863=m
-CONFIG_NLS_CODEPAGE_864=m
-CONFIG_NLS_CODEPAGE_865=m
-CONFIG_NLS_CODEPAGE_866=m
-CONFIG_NLS_CODEPAGE_869=m
-CONFIG_NLS_CODEPAGE_936=m
-CONFIG_NLS_CODEPAGE_950=m
-CONFIG_NLS_CODEPAGE_932=m
-CONFIG_NLS_CODEPAGE_949=m
-CONFIG_NLS_CODEPAGE_874=m
-CONFIG_NLS_ISO8859_8=m
-CONFIG_NLS_CODEPAGE_1250=m
-CONFIG_NLS_CODEPAGE_1251=m
-CONFIG_NLS_ASCII=m
-CONFIG_NLS_ISO8859_1=m
-CONFIG_NLS_ISO8859_2=m
-CONFIG_NLS_ISO8859_3=m
-CONFIG_NLS_ISO8859_4=m
-CONFIG_NLS_ISO8859_5=m
-CONFIG_NLS_ISO8859_6=m
-CONFIG_NLS_ISO8859_7=m
-CONFIG_NLS_ISO8859_9=m
-CONFIG_NLS_ISO8859_13=m
-CONFIG_NLS_ISO8859_14=m
-CONFIG_NLS_ISO8859_15=m
-CONFIG_NLS_KOI8_R=m
-CONFIG_NLS_KOI8_U=m
-CONFIG_NLS_UTF8=m
-CONFIG_PRINTK_TIME=y
-CONFIG_DEBUG_FS=y
-CONFIG_DEBUG_KERNEL=y
-# CONFIG_SCHED_DEBUG is not set
-CONFIG_DEBUG_RT_MUTEXES=y
-CONFIG_PROVE_LOCKING=y
-# CONFIG_FTRACE is not set
-CONFIG_DEBUG_USER=y
-CONFIG_CRYPTO_NULL=m
-CONFIG_CRYPTO_CRYPTD=m
-CONFIG_CRYPTO_TEST=m
-CONFIG_CRYPTO_ECB=m
-CONFIG_CRYPTO_LRW=m
-CONFIG_CRYPTO_PCBC=m
-CONFIG_CRYPTO_XTS=m
-CONFIG_CRYPTO_XCBC=m
-CONFIG_CRYPTO_VMAC=m
-CONFIG_CRYPTO_GHASH=m
-CONFIG_CRYPTO_MD4=m
-CONFIG_CRYPTO_MICHAEL_MIC=m
-CONFIG_CRYPTO_SHA256=m
-CONFIG_CRYPTO_SHA512=m
-CONFIG_CRYPTO_TGR192=m
-CONFIG_CRYPTO_AES=m
-CONFIG_CRYPTO_ARC4=m
-CONFIG_CRYPTO_BLOWFISH=m
-CONFIG_CRYPTO_CAST5=m
-CONFIG_CRYPTO_CAST6=m
-CONFIG_CRYPTO_FCRYPT=m
-CONFIG_CRYPTO_KHAZAD=m
-CONFIG_CRYPTO_SEED=m
-CONFIG_CRYPTO_SERPENT=m
-CONFIG_CRYPTO_TEA=m
-CONFIG_CRYPTO_TWOFISH=m
-# CONFIG_CRYPTO_ANSI_CPRNG is not set
-CONFIG_CRC16=y
diff --git a/arch/arm/configs/imx_v4_v5_defconfig b/arch/arm/configs/imx_v4_v5_defconfig
index 1d9fa77bbafc..711a79e9be00 100644
--- a/arch/arm/configs/imx_v4_v5_defconfig
+++ b/arch/arm/configs/imx_v4_v5_defconfig
@@ -1,15 +1,12 @@
-# CONFIG_SWAP is not set
 CONFIG_SYSVIPC=y
 CONFIG_POSIX_MQUEUE=y
-CONFIG_NO_HZ=y
+CONFIG_NO_HZ_IDLE=y
 CONFIG_HIGH_RES_TIMERS=y
 CONFIG_PREEMPT=y
 CONFIG_LOG_BUF_SHIFT=14
 CONFIG_CGROUPS=y
 CONFIG_BLK_DEV_INITRD=y
 CONFIG_EXPERT=y
-# CONFIG_COMPAT_BRK is not set
-CONFIG_SLAB=y
 CONFIG_PROFILING=y
 CONFIG_ARCH_MULTI_V4T=y
 CONFIG_ARCH_MULTI_V5=y
@@ -24,13 +21,13 @@ CONFIG_SOC_IMX1=y
 CONFIG_SOC_IMX25=y
 CONFIG_SOC_IMX27=y
 CONFIG_AEABI=y
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
 CONFIG_PM_DEBUG=y
 CONFIG_KPROBES=y
 CONFIG_MODULES=y
 CONFIG_MODULE_UNLOAD=y
-# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_SWAP is not set
+CONFIG_SLAB=y
+# CONFIG_COMPAT_BRK is not set
 CONFIG_NET=y
 CONFIG_PACKET=y
 CONFIG_UNIX=y
@@ -63,6 +60,7 @@ CONFIG_MTD_UBI=y
 CONFIG_EEPROM_AT24=y
 CONFIG_EEPROM_AT25=y
 CONFIG_BLK_DEV_SD=y
+# CONFIG_BLK_DEV_BSG is not set
 CONFIG_ATA=y
 CONFIG_PATA_IMX=y
 CONFIG_NETDEVICES=y
diff --git a/arch/arm/configs/imx_v6_v7_defconfig b/arch/arm/configs/imx_v6_v7_defconfig
index 1fbb8e45e604..078d61b758a9 100644
--- a/arch/arm/configs/imx_v6_v7_defconfig
+++ b/arch/arm/configs/imx_v6_v7_defconfig
@@ -1,6 +1,6 @@
 CONFIG_KERNEL_LZO=y
 CONFIG_SYSVIPC=y
-CONFIG_NO_HZ=y
+CONFIG_NO_HZ_IDLE=y
 CONFIG_HIGH_RES_TIMERS=y
 CONFIG_BPF_SYSCALL=y
 CONFIG_PREEMPT_VOLUNTARY=y
@@ -13,8 +13,6 @@ CONFIG_RELAY=y
 CONFIG_BLK_DEV_INITRD=y
 CONFIG_EXPERT=y
 CONFIG_PERF_EVENTS=y
-# CONFIG_SLUB_DEBUG is not set
-# CONFIG_COMPAT_BRK is not set
 CONFIG_ARCH_MULTI_V6=y
 CONFIG_ARCH_MXC=y
 CONFIG_SOC_IMX31=y
@@ -33,7 +31,7 @@ CONFIG_SOC_VF610=y
 CONFIG_SMP=y
 CONFIG_ARM_PSCI=y
 CONFIG_HIGHMEM=y
-CONFIG_FORCE_MAX_ZONEORDER=14
+CONFIG_ARCH_FORCE_MAX_ORDER=14
 CONFIG_CMDLINE="noinitrd console=ttymxc0,115200"
 CONFIG_KEXEC=y
 CONFIG_CPU_FREQ=y
@@ -58,6 +56,7 @@ CONFIG_MODULE_UNLOAD=y
 CONFIG_MODVERSIONS=y
 CONFIG_MODULE_SRCVERSION_ALL=y
 CONFIG_BINFMT_MISC=m
+# CONFIG_COMPAT_BRK is not set
 CONFIG_NET=y
 CONFIG_PACKET=y
 CONFIG_UNIX=y
@@ -66,7 +65,6 @@ CONFIG_IP_PNP=y
 CONFIG_IP_PNP_DHCP=y
 CONFIG_NETFILTER=y
 CONFIG_CAN=y
-CONFIG_CAN_FLEXCAN=y
 CONFIG_BT=y
 CONFIG_BT_BNEP=m
 CONFIG_BT_HCIUART=y
@@ -137,6 +135,7 @@ CONFIG_SMSC911X=y
 # CONFIG_NET_VENDOR_STMICRO is not set
 CONFIG_MICREL_PHY=y
 CONFIG_AT803X_PHY=y
+CONFIG_CAN_FLEXCAN=y
 CONFIG_USB_PEGASUS=m
 CONFIG_USB_RTL8150=m
 CONFIG_USB_RTL8152=y
@@ -258,14 +257,14 @@ CONFIG_MEDIA_SUPPORT=y
 CONFIG_MEDIA_USB_SUPPORT=y
 CONFIG_USB_VIDEO_CLASS=m
 CONFIG_V4L_PLATFORM_DRIVERS=y
-CONFIG_VIDEO_MUX=y
 CONFIG_V4L_MEM2MEM_DRIVERS=y
+CONFIG_VIDEO_MUX=y
 CONFIG_VIDEO_CODA=m
 CONFIG_VIDEO_IMX_PXP=y
-CONFIG_VIDEO_ADV7180=m
 CONFIG_VIDEO_OV2680=m
 CONFIG_VIDEO_OV5640=m
 CONFIG_VIDEO_OV5645=m
+CONFIG_VIDEO_ADV7180=m
 CONFIG_IMX_IPUV3_CORE=y
 CONFIG_DRM=y
 CONFIG_DRM_MSM=y
@@ -378,6 +377,7 @@ CONFIG_RTC_DRV_PCF8523=y
 CONFIG_RTC_DRV_PCF8563=y
 CONFIG_RTC_DRV_M41T80=y
 CONFIG_RTC_DRV_RC5T619=y
+CONFIG_RTC_DRV_RV3029C2=y
 CONFIG_RTC_DRV_DA9063=y
 CONFIG_RTC_DRV_MC13XXX=y
 CONFIG_RTC_DRV_MXC=y
@@ -401,6 +401,7 @@ CONFIG_IIO=y
 CONFIG_MMA8452=y
 CONFIG_IMX7D_ADC=y
 CONFIG_RN5T618_ADC=y
+CONFIG_STMPE_ADC=y
 CONFIG_VF610_ADC=y
 CONFIG_SENSORS_ISL29018=y
 CONFIG_MAG3110=y
@@ -466,6 +467,7 @@ CONFIG_PRINTK_TIME=y
 # CONFIG_DEBUG_BUGVERBOSE is not set
 CONFIG_MAGIC_SYSRQ=y
 CONFIG_DEBUG_FS=y
+# CONFIG_SLUB_DEBUG is not set
 # CONFIG_SCHED_DEBUG is not set
 CONFIG_PROVE_LOCKING=y
 # CONFIG_FTRACE is not set
diff --git a/arch/arm/configs/imxrt_defconfig b/arch/arm/configs/imxrt_defconfig
new file mode 100644
index 000000000000..52dba3762996
--- /dev/null
+++ b/arch/arm/configs/imxrt_defconfig
@@ -0,0 +1,35 @@
+# CONFIG_LOCALVERSION_AUTO is not set
+CONFIG_BPF_SYSCALL=y
+CONFIG_SCHED_AUTOGROUP=y
+# CONFIG_MMU is not set
+CONFIG_ARCH_MXC=y
+CONFIG_SOC_IMXRT=y
+CONFIG_SET_MEM_PARAM=y
+CONFIG_DRAM_BASE=0x80000000
+CONFIG_DRAM_SIZE=0x02000000
+CONFIG_BINFMT_FLAT=y
+CONFIG_UEVENT_HELPER=y
+CONFIG_DEVTMPFS=y
+CONFIG_DEVTMPFS_MOUNT=y
+CONFIG_IMX_WEIM=y
+CONFIG_LEGACY_PTY_COUNT=2
+CONFIG_SERIAL_FSL_LPUART=y
+CONFIG_SERIAL_FSL_LPUART_CONSOLE=y
+CONFIG_SERIAL_DEV_BUS=y
+CONFIG_PINCTRL_IMXRT1050=y
+CONFIG_GPIO_MXC=y
+CONFIG_MMC=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_PLTFM=y
+CONFIG_MMC_SDHCI_ESDHC_IMX=y
+CONFIG_DMADEVICES=y
+CONFIG_FSL_EDMA=y
+CONFIG_CLK_IMXRT1050=y
+CONFIG_EXT4_FS=y
+CONFIG_EXT4_FS_POSIX_ACL=y
+CONFIG_EXT4_FS_SECURITY=y
+CONFIG_VFAT_FS=y
+CONFIG_FAT_DEFAULT_UTF8=y
+CONFIG_EXFAT_FS=y
+CONFIG_NLS_ASCII=y
+CONFIG_NLS_UTF8=y
diff --git a/arch/arm/configs/integrator_defconfig b/arch/arm/configs/integrator_defconfig
index 4dfe321a79f6..61711d4bbf74 100644
--- a/arch/arm/configs/integrator_defconfig
+++ b/arch/arm/configs/integrator_defconfig
@@ -1,5 +1,5 @@
 CONFIG_SYSVIPC=y
-CONFIG_NO_HZ=y
+CONFIG_NO_HZ_IDLE=y
 CONFIG_HIGH_RES_TIMERS=y
 CONFIG_PREEMPT=y
 CONFIG_IKCONFIG=y
@@ -79,8 +79,7 @@ CONFIG_CRAMFS=y
 CONFIG_NFS_FS=y
 CONFIG_ROOT_NFS=y
 CONFIG_NFSD=y
-CONFIG_NFSD_V3=y
 CONFIG_NLS_CODEPAGE_437=y
 CONFIG_NLS_ISO8859_1=y
-CONFIG_MAGIC_SYSRQ=y
 CONFIG_DEBUG_KERNEL=y
+CONFIG_MAGIC_SYSRQ=y
diff --git a/arch/arm/configs/iop32x_defconfig b/arch/arm/configs/iop32x_defconfig
index 18a21faa834c..19e30e790d35 100644
--- a/arch/arm/configs/iop32x_defconfig
+++ b/arch/arm/configs/iop32x_defconfig
@@ -3,21 +3,19 @@ CONFIG_BSD_PROCESS_ACCT=y
 CONFIG_LOG_BUF_SHIFT=14
 CONFIG_BLK_DEV_INITRD=y
 CONFIG_KALLSYMS_ALL=y
-CONFIG_SLAB=y
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
-# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_ARCH_MULTI_V7 is not set
 CONFIG_ARCH_IOP32X=y
 CONFIG_MACH_GLANTANK=y
 CONFIG_ARCH_IQ80321=y
 CONFIG_ARCH_IQ31244=y
 CONFIG_MACH_N2100=y
-# CONFIG_ARM_THUMB is not set
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_UNUSED_BOARD_FILES=y
 CONFIG_CMDLINE="console=ttyS0,115200 root=/dev/nfs ip=bootp cachepolicy=writealloc"
 CONFIG_FPE_NWFPE=y
-CONFIG_BINFMT_AOUT=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_PARTITION_ADVANCED=y
+CONFIG_SLAB=y
 CONFIG_NET=y
 CONFIG_PACKET=y
 CONFIG_UNIX=y
@@ -44,6 +42,7 @@ CONFIG_BLK_DEV_RAM=y
 CONFIG_BLK_DEV_RAM_SIZE=8192
 CONFIG_BLK_DEV_SD=y
 CONFIG_CHR_DEV_SG=y
+# CONFIG_BLK_DEV_BSG is not set
 CONFIG_ATA=y
 CONFIG_SATA_SIL=y
 CONFIG_SATA_VITESSE=y
@@ -94,13 +93,6 @@ CONFIG_NFS_FS=y
 CONFIG_NFS_V3=y
 CONFIG_ROOT_NFS=y
 CONFIG_NFSD=y
-CONFIG_NFSD_V3=y
-CONFIG_PARTITION_ADVANCED=y
-CONFIG_MAGIC_SYSRQ=y
-CONFIG_DEBUG_KERNEL=y
-CONFIG_DEBUG_USER=y
-CONFIG_DEBUG_LL=y
-CONFIG_DEBUG_LL_UART_8250=y
 CONFIG_KEYS=y
 CONFIG_CRYPTO_NULL=y
 CONFIG_CRYPTO_LRW=y
@@ -127,3 +119,8 @@ CONFIG_CRYPTO_TEA=y
 CONFIG_CRYPTO_TWOFISH=y
 CONFIG_CRYPTO_DEFLATE=y
 CONFIG_LIBCRC32C=y
+CONFIG_DEBUG_KERNEL=y
+CONFIG_MAGIC_SYSRQ=y
+CONFIG_DEBUG_USER=y
+CONFIG_DEBUG_LL=y
+CONFIG_DEBUG_LL_UART_8250=y
diff --git a/arch/arm/configs/ixp4xx_defconfig b/arch/arm/configs/ixp4xx_defconfig
index 9a7667383df9..3cb995b9616a 100644
--- a/arch/arm/configs/ixp4xx_defconfig
+++ b/arch/arm/configs/ixp4xx_defconfig
@@ -1,36 +1,21 @@
+CONFIG_KERNEL_XZ=y
 CONFIG_SYSVIPC=y
 CONFIG_BSD_PROCESS_ACCT=y
 CONFIG_LOG_BUF_SHIFT=14
+CONFIG_CGROUPS=y
 CONFIG_BLK_DEV_INITRD=y
+CONFIG_INITRAMFS_COMPRESSION_XZ=y
 CONFIG_EXPERT=y
-CONFIG_MODULES=y
-CONFIG_MODVERSIONS=y
-# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_ARCH_MULTI_V7 is not set
 CONFIG_ARCH_IXP4XX=y
-CONFIG_MACH_NSLU2=y
-CONFIG_MACH_AVILA=y
-CONFIG_MACH_LOFT=y
-CONFIG_ARCH_ADI_COYOTE=y
-CONFIG_MACH_GATEWAY7001=y
-CONFIG_MACH_WG302V2=y
-CONFIG_ARCH_IXDP425=y
-CONFIG_MACH_IXDPG425=y
-CONFIG_MACH_IXDP465=y
-CONFIG_MACH_KIXRP435=y
-CONFIG_ARCH_PRPMC1100=y
-CONFIG_MACH_NAS100D=y
-CONFIG_MACH_DSMG600=y
-CONFIG_MACH_FSG=y
-CONFIG_MACH_GTWX5715=y
-CONFIG_IXP4XX_QMGR=y
-CONFIG_IXP4XX_NPE=y
-# CONFIG_ARM_THUMB is not set
 CONFIG_CPU_BIG_ENDIAN=y
 CONFIG_AEABI=y
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
-CONFIG_CMDLINE="console=ttyS0,115200 ip=bootp root=/dev/nfs"
-CONFIG_FPE_NWFPE=y
+CONFIG_CMDLINE="console=ttyS0,115200"
+CONFIG_STRICT_KERNEL_RWX=y
+CONFIG_STRICT_MODULE_RWX=y
+CONFIG_MODULES=y
+CONFIG_MODVERSIONS=y
+CONFIG_PARTITION_ADVANCED=y
 CONFIG_NET=y
 CONFIG_PACKET=y
 CONFIG_UNIX=y
@@ -43,8 +28,6 @@ CONFIG_IP_ROUTE_VERBOSE=y
 CONFIG_IP_PNP=y
 CONFIG_IP_PNP_DHCP=y
 CONFIG_IP_PNP_BOOTP=y
-CONFIG_NET_IPGRE=m
-CONFIG_NET_IPGRE_BROADCAST=y
 CONFIG_IP_MROUTE=y
 CONFIG_IP_PIMSM_V1=y
 CONFIG_IP_PIMSM_V2=y
@@ -65,7 +48,6 @@ CONFIG_IP_NF_IPTABLES=m
 CONFIG_IP_NF_MATCH_TTL=m
 CONFIG_IP_NF_FILTER=m
 CONFIG_IP_NF_TARGET_REJECT=m
-CONFIG_IP_NF_TARGET_LOG=m
 CONFIG_IP_NF_MANGLE=m
 CONFIG_IP_NF_ARPTABLES=m
 CONFIG_IP_NF_ARPFILTER=m
@@ -76,14 +58,12 @@ CONFIG_ATM_MPOA=m
 CONFIG_ATM_BR2684=m
 CONFIG_BRIDGE=m
 CONFIG_VLAN_8021Q=m
-CONFIG_IPX=m
 CONFIG_ATALK=m
 CONFIG_DEV_APPLETALK=m
 CONFIG_IPDDP=m
 CONFIG_IPDDP_ENCAP=y
 CONFIG_X25=m
 CONFIG_LAPB=m
-CONFIG_WAN_ROUTER=m
 CONFIG_NET_SCHED=y
 CONFIG_NET_SCH_CBQ=m
 CONFIG_NET_SCH_HTB=m
@@ -104,91 +84,92 @@ CONFIG_NET_CLS_RSVP6=m
 CONFIG_NET_CLS_ACT=y
 CONFIG_NET_ACT_POLICE=y
 CONFIG_NET_PKTGEN=m
+CONFIG_DEVTMPFS=y
 CONFIG_MTD=y
 CONFIG_MTD_REDBOOT_PARTS=y
 CONFIG_MTD_BLOCK=y
 CONFIG_MTD_CFI=y
 CONFIG_MTD_CFI_INTELEXT=y
+CONFIG_MTD_COMPLEX_MAPPINGS=y
 CONFIG_MTD_PHYSMAP=y
 CONFIG_MTD_PHYSMAP_OF=y
-CONFIG_MTD_COMPLEX_MAPPINGS=y
-CONFIG_MTD_IXP4XX=y
+CONFIG_MTD_PHYSMAP_IXP4XX=y
 CONFIG_MTD_RAW_NAND=m
 CONFIG_BLK_DEV_LOOP=y
 CONFIG_BLK_DEV_RAM=y
 CONFIG_BLK_DEV_RAM_SIZE=8192
-CONFIG_EEPROM_LEGACY=y
+CONFIG_EEPROM_AT24=y
+# CONFIG_EEPROM_LEGACY is not set
 # CONFIG_SCSI_PROC_FS is not set
 CONFIG_BLK_DEV_SD=y
+# CONFIG_BLK_DEV_BSG is not set
 # CONFIG_SCSI_LOWLEVEL is not set
 CONFIG_ATA=y
-CONFIG_SATA_VIA=y
-CONFIG_PATA_ARTOP=y
-CONFIG_PATA_CMD64X=y
-CONFIG_PATA_HPT366=y
-CONFIG_PATA_HPT37X=y
-CONFIG_PATA_HPT3X2N=y
-CONFIG_PATA_PDC2027X=y
 CONFIG_PATA_IXP4XX_CF=y
 CONFIG_NETDEVICES=y
 CONFIG_DUMMY=y
-CONFIG_NET_ETHERNET=y
-CONFIG_MII=y
+CONFIG_ATM_TCP=m
 CONFIG_IXP4XX_ETH=y
-CONFIG_NET_PCI=y
 CONFIG_WAN=y
-CONFIG_HDLC=m
+CONFIG_HDLC=y
 CONFIG_HDLC_RAW=m
 CONFIG_HDLC_CISCO=m
 CONFIG_HDLC_FR=m
 CONFIG_HDLC_PPP=m
-CONFIG_HDLC_X25=m
-CONFIG_WAN_ROUTER_DRIVERS=m
-CONFIG_ATM_TCP=m
-# CONFIG_INPUT_KEYBOARD is not set
+CONFIG_IXP4XX_HSS=m
+# CONFIG_KEYBOARD_ATKBD is not set
+CONFIG_KEYBOARD_GPIO=y
 # CONFIG_INPUT_MOUSE is not set
 CONFIG_INPUT_MISC=y
-CONFIG_INPUT_IXP4XX_BEEPER=y
 # CONFIG_SERIO is not set
 # CONFIG_VT is not set
 CONFIG_SERIAL_8250=y
 CONFIG_SERIAL_8250_CONSOLE=y
 CONFIG_SERIAL_8250_NR_UARTS=2
+CONFIG_SERIAL_8250_RUNTIME_UARTS=2
 CONFIG_SERIAL_OF_PLATFORM=y
-CONFIG_I2C=y
+CONFIG_HW_RANDOM=y
 CONFIG_I2C_CHARDEV=y
+CONFIG_I2C_GPIO=y
+CONFIG_GPIO_GW_PLD=y
+CONFIG_GPIO_PCA953X=y
+CONFIG_SENSORS_AD7418=y
 CONFIG_SENSORS_W83781D=y
 CONFIG_WATCHDOG=y
 CONFIG_IXP4XX_WATCHDOG=y
 CONFIG_USB=y
 CONFIG_USB_EHCI_HCD=y
 CONFIG_USB_OHCI_HCD=y
-CONFIG_USB_UHCI_HCD=y
 CONFIG_USB_STORAGE=y
 CONFIG_NEW_LEDS=y
 CONFIG_LEDS_CLASS=y
-CONFIG_LEDS_FSG=y
 CONFIG_LEDS_GPIO=y
 CONFIG_LEDS_TRIGGERS=y
 CONFIG_LEDS_TRIGGER_TIMER=y
 CONFIG_LEDS_TRIGGER_DISK=y
 CONFIG_LEDS_TRIGGER_HEARTBEAT=y
 CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_DS1672=y
 CONFIG_RTC_DRV_ISL1208=y
 CONFIG_RTC_DRV_X1205=y
 CONFIG_RTC_DRV_PCF8563=y
+CONFIG_IXP4XX_QMGR=y
+CONFIG_IXP4XX_NPE=y
 CONFIG_EXT2_FS=y
 CONFIG_EXT2_FS_XATTR=y
 CONFIG_EXT2_FS_POSIX_ACL=y
 CONFIG_EXT3_FS=y
 CONFIG_EXT3_FS_POSIX_ACL=y
+CONFIG_OVERLAY_FS=y
 CONFIG_TMPFS=y
+CONFIG_TMPFS_POSIX_ACL=y
 CONFIG_JFFS2_FS=y
+CONFIG_SQUASHFS=y
+CONFIG_SQUASHFS_XZ=y
 CONFIG_NFS_FS=y
-CONFIG_NFS_V3=y
 CONFIG_ROOT_NFS=y
-CONFIG_PARTITION_ADVANCED=y
+CONFIG_CRYPTO_DEV_IXP4XX=y
 CONFIG_MAGIC_SYSRQ=y
-CONFIG_DEBUG_KERNEL=y
+CONFIG_DEBUG_FS=y
 CONFIG_DEBUG_LL=y
 CONFIG_DEBUG_LL_UART_8250=y
diff --git a/arch/arm/configs/jornada720_defconfig b/arch/arm/configs/jornada720_defconfig
index 069f60ffdcd8..ae1d68da4f2a 100644
--- a/arch/arm/configs/jornada720_defconfig
+++ b/arch/arm/configs/jornada720_defconfig
@@ -1,18 +1,15 @@
 CONFIG_SYSVIPC=y
 CONFIG_LOG_BUF_SHIFT=14
 CONFIG_SYSFS_DEPRECATED_V2=y
-CONFIG_MODULES=y
-# CONFIG_BLK_DEV_BSG is not set
+CONFIG_ARCH_MULTI_V4=y
+# CONFIG_ARCH_MULTI_V7 is not set
 CONFIG_ARCH_SA1100=y
 CONFIG_SA1100_JORNADA720=y
 CONFIG_SA1100_JORNADA720_SSP=y
-CONFIG_PCCARD=y
-CONFIG_PCMCIA_SA1100=y
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_UNUSED_BOARD_FILES=y
 CONFIG_FPE_NWFPE=y
-CONFIG_BINFMT_AOUT=y
 CONFIG_PM=y
+CONFIG_MODULES=y
 CONFIG_NET=y
 CONFIG_PACKET=y
 CONFIG_UNIX=y
@@ -20,13 +17,12 @@ CONFIG_INET=y
 CONFIG_IP_MULTICAST=y
 # CONFIG_IPV6 is not set
 CONFIG_NETFILTER=y
-CONFIG_IRDA=m
-CONFIG_IRLAN=m
-CONFIG_IRCOMM=m
-CONFIG_SA1100_FIR=m
+CONFIG_PCCARD=y
+CONFIG_PCMCIA_SA1100=y
 CONFIG_BLK_DEV_LOOP=y
 CONFIG_BLK_DEV_NBD=y
 CONFIG_BLK_DEV_SD=y
+# CONFIG_BLK_DEV_BSG is not set
 CONFIG_ATA=y
 CONFIG_PATA_PCMCIA=y
 CONFIG_NETDEVICES=y
@@ -40,9 +36,9 @@ CONFIG_KEYBOARD_HP7XX=y
 # CONFIG_INPUT_MOUSE is not set
 CONFIG_INPUT_TOUCHSCREEN=y
 CONFIG_TOUCHSCREEN_HP7XX=y
+CONFIG_LEGACY_PTY_COUNT=32
 CONFIG_SERIAL_SA1100=y
 CONFIG_SERIAL_SA1100_CONSOLE=y
-CONFIG_LEGACY_PTY_COUNT=32
 # CONFIG_HWMON is not set
 CONFIG_FB=y
 CONFIG_FB_S1D13XXX=y
diff --git a/arch/arm/configs/keystone_defconfig b/arch/arm/configs/keystone_defconfig
index 33c917df7b32..4a5b9adbf2a1 100644
--- a/arch/arm/configs/keystone_defconfig
+++ b/arch/arm/configs/keystone_defconfig
@@ -1,43 +1,41 @@
-# CONFIG_SWAP is not set
 CONFIG_POSIX_MQUEUE=y
 CONFIG_HIGH_RES_TIMERS=y
+CONFIG_PREEMPT=y
 CONFIG_IKCONFIG=y
 CONFIG_IKCONFIG_PROC=y
 CONFIG_LOG_BUF_SHIFT=14
 CONFIG_CGROUPS=y
+CONFIG_BLK_CGROUP=y
+CONFIG_CGROUP_SCHED=y
 CONFIG_CGROUP_FREEZER=y
 CONFIG_CGROUP_DEVICE=y
 CONFIG_CGROUP_CPUACCT=y
-CONFIG_CGROUP_SCHED=y
-CONFIG_BLK_CGROUP=y
 CONFIG_BLK_DEV_INITRD=y
-CONFIG_KALLSYMS_ALL=y
 # CONFIG_ELF_CORE is not set
 # CONFIG_BASE_FULL is not set
+CONFIG_KALLSYMS_ALL=y
 CONFIG_EMBEDDED=y
 CONFIG_PROFILING=y
-CONFIG_KPROBES=y
-CONFIG_MODULES=y
-CONFIG_MODULE_FORCE_LOAD=y
-CONFIG_MODULE_UNLOAD=y
-CONFIG_MODULE_FORCE_UNLOAD=y
-CONFIG_MODVERSIONS=y
 CONFIG_ARCH_KEYSTONE=y
 CONFIG_ARM_LPAE=y
-CONFIG_PCI=y
-CONFIG_PCI_MSI=y
 CONFIG_PCI_KEYSTONE=y
 CONFIG_SMP=y
 CONFIG_HOTPLUG_CPU=y
 CONFIG_ARM_PSCI=y
-CONFIG_PREEMPT=y
 CONFIG_AEABI=y
 CONFIG_HIGHMEM=y
-CONFIG_CMA=y
 CONFIG_VFP=y
 CONFIG_NEON=y
 # CONFIG_SUSPEND is not set
 CONFIG_PM=y
+CONFIG_KPROBES=y
+CONFIG_MODULES=y
+CONFIG_MODULE_FORCE_LOAD=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_MODULE_FORCE_UNLOAD=y
+CONFIG_MODVERSIONS=y
+# CONFIG_SWAP is not set
+CONFIG_CMA=y
 CONFIG_NET=y
 CONFIG_PACKET=y
 CONFIG_UNIX=y
@@ -111,11 +109,11 @@ CONFIG_IP6_NF_IPTABLES=m
 CONFIG_IP_SCTP=y
 CONFIG_VLAN_8021Q=y
 CONFIG_CAN=m
-CONFIG_CAN_C_CAN=m
-CONFIG_CAN_C_CAN_PLATFORM=m
+CONFIG_PCI=y
+CONFIG_PCI_MSI=y
 CONFIG_DEVTMPFS=y
 CONFIG_DEVTMPFS_MOUNT=y
-CONFIG_DMA_CMA=y
+CONFIG_TI_SCI_PROTOCOL=y
 CONFIG_MTD=y
 CONFIG_MTD_CMDLINE_PARTS=y
 CONFIG_MTD_BLOCK=y
@@ -131,10 +129,17 @@ CONFIG_EEPROM_AT24=y
 CONFIG_SCSI=y
 CONFIG_BLK_DEV_SD=y
 CONFIG_NETDEVICES=y
+CONFIG_TI_CPTS=y
 CONFIG_TI_KEYSTONE_NETCP=y
 CONFIG_TI_KEYSTONE_NETCP_ETHSS=y
-CONFIG_TI_CPTS=y
 CONFIG_MARVELL_PHY=y
+CONFIG_MICREL_PHY=y
+CONFIG_DP83867_PHY=y
+CONFIG_CAN_C_CAN=m
+CONFIG_CAN_C_CAN_PLATFORM=m
+CONFIG_INPUT_EVDEV=m
+CONFIG_INPUT_MISC=y
+CONFIG_INPUT_GPIO_DECODER=m
 CONFIG_SERIAL_8250=y
 CONFIG_SERIAL_8250_CONSOLE=y
 CONFIG_SERIAL_OF_PLATFORM=y
@@ -144,17 +149,18 @@ CONFIG_I2C=y
 CONFIG_I2C_CHARDEV=y
 CONFIG_I2C_DAVINCI=y
 CONFIG_SPI=y
+CONFIG_SPI_CADENCE_QUADSPI=y
 CONFIG_SPI_DAVINCI=y
 CONFIG_SPI_SPIDEV=y
-CONFIG_PTP_1588_CLOCK=y
 CONFIG_PINCTRL_SINGLE=y
 CONFIG_GPIOLIB=y
 CONFIG_GPIO_SYSFS=y
 CONFIG_GPIO_DAVINCI=y
 CONFIG_GPIO_SYSCON=y
-CONFIG_POWER_SUPPLY=y
+CONFIG_GPIO_PCA953X=m
 CONFIG_POWER_RESET=y
 CONFIG_POWER_RESET_KEYSTONE=y
+CONFIG_POWER_SUPPLY=y
 # CONFIG_HWMON is not set
 CONFIG_WATCHDOG=y
 CONFIG_DAVINCI_WATCHDOG=y
@@ -166,8 +172,8 @@ CONFIG_USB_MON=y
 CONFIG_USB_XHCI_HCD=y
 CONFIG_USB_STORAGE=y
 CONFIG_USB_DWC3=y
-CONFIG_NOP_USB_XCEIV=y
 CONFIG_KEYSTONE_USB_PHY=y
+CONFIG_NOP_USB_XCEIV=y
 CONFIG_MMC=y
 CONFIG_MMC_SDHCI=y
 CONFIG_MMC_SDHCI_PLTFM=y
@@ -180,6 +186,8 @@ CONFIG_LEDS_TRIGGERS=y
 CONFIG_LEDS_TRIGGER_ONESHOT=y
 CONFIG_LEDS_TRIGGER_HEARTBEAT=y
 CONFIG_LEDS_TRIGGER_BACKLIGHT=y
+CONFIG_LEDS_TRIGGER_CPU=y
+CONFIG_LEDS_TRIGGER_ACTIVITY=y
 CONFIG_LEDS_TRIGGER_GPIO=y
 CONFIG_DMADEVICES=y
 CONFIG_TI_EDMA=y
@@ -196,7 +204,6 @@ CONFIG_PWM_TIECAP=m
 CONFIG_KEYSTONE_IRQ=y
 CONFIG_RESET_TI_SCI=m
 CONFIG_RESET_TI_SYSCON=m
-CONFIG_TI_SCI_PROTOCOL=y
 CONFIG_EXT4_FS=y
 CONFIG_EXT4_FS_POSIX_ACL=y
 CONFIG_FANOTIFY=y
@@ -213,14 +220,9 @@ CONFIG_NFS_FS=y
 CONFIG_NFS_V3_ACL=y
 CONFIG_ROOT_NFS=y
 CONFIG_NFSD=y
-CONFIG_NFSD_V3=y
 CONFIG_NFSD_V3_ACL=y
 CONFIG_NLS_CODEPAGE_437=y
 CONFIG_NLS_ISO8859_1=y
-CONFIG_PRINTK_TIME=y
-CONFIG_DEBUG_INFO=y
-CONFIG_DEBUG_SHIRQ=y
-CONFIG_DEBUG_USER=y
 CONFIG_CRYPTO_USER=y
 CONFIG_CRYPTO_AUTHENC=y
 CONFIG_CRYPTO_CBC=y
@@ -230,12 +232,8 @@ CONFIG_CRYPTO_DES=y
 CONFIG_CRYPTO_ANSI_CPRNG=y
 CONFIG_CRYPTO_USER_API_HASH=y
 CONFIG_CRYPTO_USER_API_SKCIPHER=y
-CONFIG_SPI_CADENCE_QUADSPI=y
-CONFIG_INPUT_MISC=y
-CONFIG_INPUT_EVDEV=m
-CONFIG_INPUT_GPIO_DECODER=m
-CONFIG_GPIO_PCA953X=m
-CONFIG_LEDS_TRIGGER_ACTIVITY=y
-CONFIG_LEDS_TRIGGER_CPU=y
-CONFIG_MICREL_PHY=y
-CONFIG_DP83867_PHY=y
+CONFIG_DMA_CMA=y
+CONFIG_PRINTK_TIME=y
+CONFIG_DEBUG_INFO_DWARF_TOOLCHAIN_DEFAULT=y
+CONFIG_DEBUG_SHIRQ=y
+CONFIG_DEBUG_USER=y
diff --git a/arch/arm/configs/lart_defconfig b/arch/arm/configs/lart_defconfig
index b6ddb9884326..916177d07a39 100644
--- a/arch/arm/configs/lart_defconfig
+++ b/arch/arm/configs/lart_defconfig
@@ -1,32 +1,23 @@
 CONFIG_SYSVIPC=y
 CONFIG_LOG_BUF_SHIFT=14
 CONFIG_BLK_DEV_INITRD=y
-CONFIG_MODULES=y
+CONFIG_ARCH_MULTI_V4=y
+# CONFIG_ARCH_MULTI_V7 is not set
 CONFIG_ARCH_SA1100=y
 CONFIG_SA1100_LART=y
-CONFIG_LEDS=y
-CONFIG_LEDS_CPU=y
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_UNUSED_BOARD_FILES=y
 CONFIG_CMDLINE="console=ttySA0,9600 root=/dev/ram"
 CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE=y
 CONFIG_CPU_FREQ_GOV_USERSPACE=y
 CONFIG_FPE_NWFPE=y
-CONFIG_BINFMT_AOUT=y
 CONFIG_PM=y
+CONFIG_MODULES=y
 CONFIG_NET=y
 CONFIG_PACKET=m
 CONFIG_UNIX=y
 CONFIG_INET=y
 CONFIG_SYN_COOKIES=y
 # CONFIG_IPV6 is not set
-CONFIG_IRDA=m
-CONFIG_IRLAN=m
-CONFIG_IRNET=m
-CONFIG_IRCOMM=m
-CONFIG_IRDA_CACHE_LAST_LSAP=y
-CONFIG_IRDA_DEBUG=y
-CONFIG_SA1100_FIR=m
 CONFIG_MTD=y
 CONFIG_MTD_DEBUG=y
 CONFIG_MTD_DEBUG_VERBOSE=1
@@ -37,15 +28,19 @@ CONFIG_NETDEVICES=y
 CONFIG_DUMMY=m
 CONFIG_NET_ETHERNET=y
 CONFIG_PPP=m
-CONFIG_PPP_ASYNC=m
-CONFIG_PPP_DEFLATE=m
 CONFIG_PPP_BSDCOMP=m
+CONFIG_PPP_DEFLATE=m
+CONFIG_PPP_ASYNC=m
 CONFIG_SLIP=m
 CONFIG_SLIP_COMPRESSED=y
 CONFIG_SERIAL_SA1100=y
 CONFIG_SERIAL_SA1100_CONSOLE=y
 # CONFIG_VGA_CONSOLE is not set
 CONFIG_SOUND=m
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=y
+CONFIG_LEDS_TRIGGERS=y
+CONFIG_LEDS_TRIGGER_CPU=y
 CONFIG_EXT2_FS=y
 CONFIG_EXT3_FS=m
 CONFIG_REISERFS_FS=m
@@ -59,7 +54,6 @@ CONFIG_CRAMFS=m
 CONFIG_NFS_FS=m
 CONFIG_NFS_V3=y
 CONFIG_NFSD=m
-CONFIG_NFSD_V3=y
 CONFIG_NLS=y
 CONFIG_NLS_CODEPAGE_437=m
 CONFIG_NLS_CODEPAGE_850=m
diff --git a/arch/arm/configs/lpc18xx_defconfig b/arch/arm/configs/lpc18xx_defconfig
index be882ea0eee4..56eae6a0a311 100644
--- a/arch/arm/configs/lpc18xx_defconfig
+++ b/arch/arm/configs/lpc18xx_defconfig
@@ -15,8 +15,6 @@ CONFIG_CC_OPTIMIZE_FOR_SIZE=y
 # CONFIG_EVENTFD is not set
 # CONFIG_AIO is not set
 CONFIG_EMBEDDED=y
-# CONFIG_VM_EVENT_COUNTERS is not set
-# CONFIG_SLUB_DEBUG is not set
 # CONFIG_MMU is not set
 CONFIG_ARCH_LPC18XX=y
 CONFIG_SET_MEM_PARAM=y
@@ -24,14 +22,11 @@ CONFIG_DRAM_BASE=0x28000000
 CONFIG_DRAM_SIZE=0x02000000
 CONFIG_FLASH_MEM_BASE=0x1b000000
 CONFIG_FLASH_SIZE=0x00080000
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
 CONFIG_ARM_APPENDED_DTB=y
-# CONFIG_BLK_DEV_BSG is not set
 CONFIG_BINFMT_FLAT=y
 CONFIG_BINFMT_ZFLAT=y
-CONFIG_BINFMT_SHARED_FLAT=y
 # CONFIG_COREDUMP is not set
+# CONFIG_VM_EVENT_COUNTERS is not set
 CONFIG_NET=y
 CONFIG_PACKET=y
 CONFIG_UNIX=y
@@ -61,6 +56,7 @@ CONFIG_SRAM=y
 CONFIG_EEPROM_AT24=y
 CONFIG_SCSI=y
 CONFIG_BLK_DEV_SD=y
+# CONFIG_BLK_DEV_BSG is not set
 # CONFIG_SCSI_LOWLEVEL is not set
 CONFIG_NETDEVICES=y
 # CONFIG_NET_VENDOR_ARC is not set
@@ -93,11 +89,11 @@ CONFIG_KEYBOARD_GPIO_POLLED=y
 # CONFIG_VT is not set
 # CONFIG_UNIX98_PTYS is not set
 # CONFIG_LEGACY_PTYS is not set
-CONFIG_SERIAL_NONSTANDARD=y
 CONFIG_SERIAL_8250=y
 # CONFIG_SERIAL_8250_DEPRECATED_OPTIONS is not set
 CONFIG_SERIAL_8250_CONSOLE=y
 CONFIG_SERIAL_OF_PLATFORM=y
+CONFIG_SERIAL_NONSTANDARD=y
 # CONFIG_HW_RANDOM is not set
 CONFIG_I2C_LPC2K=y
 CONFIG_SPI=y
@@ -154,11 +150,12 @@ CONFIG_JFFS2_FS=y
 CONFIG_CRC_ITU_T=y
 CONFIG_CRC7=y
 CONFIG_PRINTK_TIME=y
-CONFIG_DEBUG_INFO=y
 # CONFIG_ENABLE_MUST_CHECK is not set
-CONFIG_DEBUG_FS=y
+# CONFIG_DEBUG_BUGVERBOSE is not set
+CONFIG_DEBUG_INFO_DWARF_TOOLCHAIN_DEFAULT=y
 CONFIG_MAGIC_SYSRQ=y
+CONFIG_DEBUG_FS=y
+# CONFIG_SLUB_DEBUG is not set
 # CONFIG_SCHED_DEBUG is not set
-# CONFIG_DEBUG_BUGVERBOSE is not set
 CONFIG_DEBUG_LL=y
 CONFIG_EARLY_PRINTK=y
diff --git a/arch/arm/configs/lpc32xx_defconfig b/arch/arm/configs/lpc32xx_defconfig
index 6c3e4a141963..fabb66a53350 100644
--- a/arch/arm/configs/lpc32xx_defconfig
+++ b/arch/arm/configs/lpc32xx_defconfig
@@ -1,5 +1,5 @@
 CONFIG_SYSVIPC=y
-CONFIG_NO_HZ=y
+CONFIG_NO_HZ_IDLE=y
 CONFIG_HIGH_RES_TIMERS=y
 CONFIG_PREEMPT=y
 CONFIG_IKCONFIG=y
@@ -10,12 +10,9 @@ CONFIG_SYSFS_DEPRECATED_V2=y
 CONFIG_BLK_DEV_INITRD=y
 CONFIG_CC_OPTIMIZE_FOR_SIZE=y
 CONFIG_EMBEDDED=y
-CONFIG_SLAB=y
 # CONFIG_ARCH_MULTI_V7 is not set
 CONFIG_ARCH_LPC32XX=y
 CONFIG_AEABI=y
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
 CONFIG_ARM_APPENDED_DTB=y
 CONFIG_ARM_ATAG_DTB_COMPAT=y
 CONFIG_CMDLINE="console=ttyS0,115200n81 root=/dev/ram0"
@@ -24,9 +21,9 @@ CONFIG_VFP=y
 CONFIG_JUMP_LABEL=y
 CONFIG_MODULES=y
 CONFIG_MODULE_UNLOAD=y
-# CONFIG_BLK_DEV_BSG is not set
 CONFIG_PARTITION_ADVANCED=y
 # CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+CONFIG_SLAB=y
 CONFIG_NET=y
 CONFIG_PACKET=y
 CONFIG_UNIX=y
@@ -60,6 +57,7 @@ CONFIG_EEPROM_AT24=y
 CONFIG_EEPROM_AT25=y
 CONFIG_SCSI=y
 CONFIG_BLK_DEV_SD=y
+# CONFIG_BLK_DEV_BSG is not set
 CONFIG_NETDEVICES=y
 # CONFIG_NET_VENDOR_BROADCOM is not set
 # CONFIG_NET_VENDOR_CIRRUS is not set
@@ -93,11 +91,11 @@ CONFIG_SERIAL_HS_LPC32XX_CONSOLE=y
 # CONFIG_HW_RANDOM is not set
 CONFIG_I2C_CHARDEV=y
 CONFIG_I2C_PNX=y
-CONFIG_GPIO_LPC32XX=y
 CONFIG_SPI=y
 CONFIG_SPI_PL022=y
 CONFIG_GPIO_SYSFS=y
 CONFIG_GPIO_GENERIC_PLATFORM=y
+CONFIG_GPIO_LPC32XX=y
 CONFIG_GPIO_PCA953X=y
 CONFIG_GPIO_PCF857X=y
 CONFIG_SENSORS_DS620=y
@@ -187,10 +185,10 @@ CONFIG_CRYPTO_ANSI_CPRNG=y
 CONFIG_CRC_CCITT=y
 CONFIG_PRINTK_TIME=y
 CONFIG_DYNAMIC_DEBUG=y
-CONFIG_DEBUG_INFO=y
+CONFIG_DEBUG_INFO_DWARF_TOOLCHAIN_DEFAULT=y
 CONFIG_GDB_SCRIPTS=y
-CONFIG_DEBUG_FS=y
 CONFIG_MAGIC_SYSRQ=y
+CONFIG_DEBUG_FS=y
 CONFIG_PANIC_ON_OOPS=y
 CONFIG_PANIC_TIMEOUT=5
 # CONFIG_SCHED_DEBUG is not set
diff --git a/arch/arm/configs/lpd270_defconfig b/arch/arm/configs/lpd270_defconfig
index 3a4d0e64cd6e..b0c21a99a0a8 100644
--- a/arch/arm/configs/lpd270_defconfig
+++ b/arch/arm/configs/lpd270_defconfig
@@ -1,14 +1,13 @@
 CONFIG_SYSVIPC=y
 CONFIG_LOG_BUF_SHIFT=14
-CONFIG_SLAB=y
-CONFIG_MODULES=y
+# CONFIG_ARCH_MULTI_V7 is not set
 CONFIG_ARCH_PXA=y
 CONFIG_MACH_LOGICPD_PXA270=y
-# CONFIG_ARM_THUMB is not set
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_UNUSED_BOARD_FILES=y
 CONFIG_CMDLINE="root=/dev/nfs ip=bootp console=ttyS0,115200 mem=64M"
 CONFIG_FPE_NWFPE=y
+CONFIG_MODULES=y
+CONFIG_SLAB=y
 CONFIG_NET=y
 CONFIG_UNIX=y
 CONFIG_INET=y
@@ -52,8 +51,8 @@ CONFIG_JFFS2_FS=y
 CONFIG_NFS_FS=y
 CONFIG_ROOT_NFS=y
 CONFIG_NLS_ISO8859_1=y
-CONFIG_MAGIC_SYSRQ=y
 CONFIG_DEBUG_KERNEL=y
-CONFIG_DEBUG_INFO=y
+CONFIG_DEBUG_INFO_DWARF_TOOLCHAIN_DEFAULT=y
+CONFIG_MAGIC_SYSRQ=y
 CONFIG_DEBUG_USER=y
 CONFIG_DEBUG_LL=y
diff --git a/arch/arm/configs/lubbock_defconfig b/arch/arm/configs/lubbock_defconfig
index 4ce2da2e76fa..4fc744c96196 100644
--- a/arch/arm/configs/lubbock_defconfig
+++ b/arch/arm/configs/lubbock_defconfig
@@ -1,23 +1,20 @@
 CONFIG_SYSVIPC=y
 CONFIG_LOG_BUF_SHIFT=14
-CONFIG_MODULES=y
+# CONFIG_ARCH_MULTI_V7 is not set
 CONFIG_ARCH_PXA=y
 CONFIG_ARCH_LUBBOCK=y
-# CONFIG_ARM_THUMB is not set
-CONFIG_PCCARD=y
-CONFIG_PCMCIA_PXA2XX=y
-CONFIG_LEDS=y
-CONFIG_LEDS_CPU=y
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_UNUSED_BOARD_FILES=y
 CONFIG_CMDLINE="root=/dev/nfs ip=bootp console=ttyS0,115200 mem=64M"
 CONFIG_FPE_NWFPE=y
+CONFIG_MODULES=y
 CONFIG_NET=y
 CONFIG_UNIX=y
 CONFIG_INET=y
 CONFIG_IP_PNP=y
 CONFIG_IP_PNP_BOOTP=y
 # CONFIG_IPV6 is not set
+CONFIG_PCCARD=y
+CONFIG_PCMCIA_PXA2XX=y
 CONFIG_MTD=y
 CONFIG_MTD_REDBOOT_PARTS=y
 CONFIG_MTD_BLOCK=y
@@ -28,9 +25,9 @@ CONFIG_MTD_CFI_GEOMETRY=y
 CONFIG_MTD_CFI_INTELEXT=y
 CONFIG_NETDEVICES=y
 CONFIG_NET_ETHERNET=y
-CONFIG_SMC91X=y
 CONFIG_NET_PCMCIA=y
 CONFIG_PCMCIA_PCNET=y
+CONFIG_SMC91X=y
 CONFIG_INPUT_EVDEV=y
 # CONFIG_SERIO_SERPORT is not set
 CONFIG_SERIO_SA1111=y
@@ -39,14 +36,18 @@ CONFIG_SERIAL_PXA_CONSOLE=y
 # CONFIG_VGA_CONSOLE is not set
 CONFIG_USB_GADGET=y
 CONFIG_USB_G_SERIAL=m
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=y
+CONFIG_LEDS_TRIGGERS=y
+CONFIG_LEDS_TRIGGER_CPU=y
 CONFIG_EXT2_FS=y
 CONFIG_MSDOS_FS=y
 CONFIG_JFFS2_FS=y
 CONFIG_NFS_FS=y
 CONFIG_ROOT_NFS=y
 CONFIG_NLS_ISO8859_1=y
-CONFIG_MAGIC_SYSRQ=y
 CONFIG_DEBUG_KERNEL=y
-CONFIG_DEBUG_INFO=y
+CONFIG_DEBUG_INFO_DWARF_TOOLCHAIN_DEFAULT=y
+CONFIG_MAGIC_SYSRQ=y
 CONFIG_DEBUG_USER=y
 CONFIG_DEBUG_LL=y
diff --git a/arch/arm/configs/magician_defconfig b/arch/arm/configs/magician_defconfig
index abde1fb23b20..5a8776f6aba3 100644
--- a/arch/arm/configs/magician_defconfig
+++ b/arch/arm/configs/magician_defconfig
@@ -1,28 +1,28 @@
 CONFIG_SYSVIPC=y
+CONFIG_NO_HZ_IDLE=y
+CONFIG_PREEMPT=y
 CONFIG_IKCONFIG=y
 CONFIG_IKCONFIG_PROC=y
 CONFIG_LOG_BUF_SHIFT=16
 CONFIG_BLK_DEV_INITRD=y
 CONFIG_EXPERT=y
 # CONFIG_UID16 is not set
-CONFIG_SLAB=y
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
 # CONFIG_BLK_DEV_BSG is not set
+# CONFIG_ARCH_MULTI_V7 is not set
 CONFIG_ARCH_PXA=y
 CONFIG_MACH_H4700=y
 CONFIG_MACH_MAGICIAN=y
-CONFIG_NO_HZ=y
-CONFIG_PREEMPT=y
 CONFIG_AEABI=y
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_UNUSED_BOARD_FILES=y
 CONFIG_CMDLINE="keepinitrd"
 CONFIG_KEXEC=y
 CONFIG_CPU_FREQ=y
 CONFIG_CPU_FREQ_GOV_ONDEMAND=y
 CONFIG_FPE_NWFPE=y
 CONFIG_PM=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_SLAB=y
 CONFIG_NET=y
 CONFIG_PACKET=y
 CONFIG_UNIX=y
@@ -34,15 +34,6 @@ CONFIG_IP_PNP=y
 # CONFIG_INET_XFRM_MODE_BEET is not set
 # CONFIG_INET_DIAG is not set
 # CONFIG_IPV6 is not set
-CONFIG_IRDA=m
-CONFIG_IRLAN=m
-CONFIG_IRCOMM=m
-CONFIG_IRDA_ULTRA=y
-CONFIG_IRDA_CACHE_LAST_LSAP=y
-CONFIG_IRDA_FAST_RR=y
-CONFIG_IRDA_DEBUG=y
-CONFIG_IRTTY_SIR=m
-CONFIG_PXA_FICP=m
 CONFIG_BT=m
 CONFIG_BT_RFCOMM=m
 CONFIG_BT_RFCOMM_TTY=y
@@ -59,11 +50,11 @@ CONFIG_MTD_CFI_INTELEXT=y
 CONFIG_MTD_PHYSMAP=y
 CONFIG_NETDEVICES=y
 CONFIG_PPP=m
-CONFIG_PPP_ASYNC=m
-CONFIG_PPP_DEFLATE=m
 CONFIG_PPP_BSDCOMP=m
+CONFIG_PPP_DEFLATE=m
 CONFIG_PPP_MPPE=m
 # CONFIG_INPUT_MOUSEDEV is not set
+CONFIG_PPP_ASYNC=m
 CONFIG_INPUT_EVDEV=y
 # CONFIG_KEYBOARD_ATKBD is not set
 CONFIG_KEYBOARD_GPIO=y
@@ -72,19 +63,19 @@ CONFIG_INPUT_TOUCHSCREEN=y
 CONFIG_INPUT_MISC=y
 CONFIG_INPUT_UINPUT=m
 # CONFIG_SERIO is not set
-CONFIG_SERIAL_PXA=y
 # CONFIG_LEGACY_PTYS is not set
+CONFIG_SERIAL_PXA=y
 # CONFIG_HW_RANDOM is not set
 CONFIG_I2C=y
 CONFIG_I2C_CHARDEV=m
 CONFIG_I2C_PXA=y
 CONFIG_W1_MASTER_DS1WM=y
+CONFIG_HTC_EGPIO=y
 CONFIG_POWER_SUPPLY=y
 CONFIG_PDA_POWER=y
 CONFIG_BATTERY_DS2760=y
 # CONFIG_HWMON is not set
 CONFIG_MFD_ASIC3=y
-CONFIG_HTC_EGPIO=y
 CONFIG_HTC_PASIC3=y
 CONFIG_REGULATOR=y
 CONFIG_REGULATOR_GPIO=y
@@ -98,8 +89,6 @@ CONFIG_BACKLIGHT_PWM=y
 # CONFIG_VGA_CONSOLE is not set
 CONFIG_FRAMEBUFFER_CONSOLE=y
 CONFIG_FRAMEBUFFER_CONSOLE_ROTATION=y
-CONFIG_FONTS=y
-CONFIG_FONT_MINI_4x6=y
 CONFIG_SOUND=y
 CONFIG_SND=m
 CONFIG_SND_MIXER_OSS=m
@@ -111,6 +100,7 @@ CONFIG_SND_PXA2XX_SOC=m
 CONFIG_USB=y
 CONFIG_USB_MON=m
 CONFIG_USB_OHCI_HCD=y
+CONFIG_USB_GPIO_VBUS=y
 CONFIG_USB_GADGET=y
 CONFIG_USB_GADGET_VBUS_DRAW=500
 CONFIG_USB_PXA27X=y
@@ -120,7 +110,6 @@ CONFIG_USB_GADGETFS=m
 CONFIG_USB_MASS_STORAGE=m
 CONFIG_USB_G_SERIAL=m
 CONFIG_USB_CDC_COMPOSITE=m
-CONFIG_USB_GPIO_VBUS=y
 CONFIG_MMC=y
 CONFIG_SDIO_UART=m
 CONFIG_MMC_PXA=y
@@ -147,6 +136,11 @@ CONFIG_NLS_CODEPAGE_437=y
 CONFIG_NLS_CODEPAGE_1251=m
 CONFIG_NLS_ISO8859_1=y
 CONFIG_NLS_UTF8=y
+CONFIG_CRYPTO=y
+# CONFIG_CRYPTO_HW is not set
+CONFIG_CRC_CCITT=y
+CONFIG_FONTS=y
+CONFIG_FONT_MINI_4x6=y
 CONFIG_PRINTK_TIME=y
 CONFIG_DEBUG_KERNEL=y
 # CONFIG_SCHED_DEBUG is not set
@@ -154,7 +148,4 @@ CONFIG_TIMER_STATS=y
 # CONFIG_DEBUG_PREEMPT is not set
 CONFIG_DEBUG_USER=y
 CONFIG_DEBUG_LL=y
-CONFIG_CRYPTO=y
 # CONFIG_CRYPTO_ANSI_CPRNG is not set
-# CONFIG_CRYPTO_HW is not set
-CONFIG_CRC_CCITT=y
diff --git a/arch/arm/configs/mainstone_defconfig b/arch/arm/configs/mainstone_defconfig
index 26499b697f9f..096cd7bc667a 100644
--- a/arch/arm/configs/mainstone_defconfig
+++ b/arch/arm/configs/mainstone_defconfig
@@ -1,15 +1,12 @@
 CONFIG_SYSVIPC=y
 CONFIG_LOG_BUF_SHIFT=14
-CONFIG_MODULES=y
+# CONFIG_ARCH_MULTI_V7 is not set
 CONFIG_ARCH_PXA=y
 CONFIG_MACH_MAINSTONE=y
-# CONFIG_ARM_THUMB is not set
-CONFIG_LEDS=y
-CONFIG_LEDS_CPU=y
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_UNUSED_BOARD_FILES=y
 CONFIG_CMDLINE="root=/dev/nfs ip=bootp console=ttyS0,115200 mem=64M"
 CONFIG_FPE_NWFPE=y
+CONFIG_MODULES=y
 CONFIG_NET=y
 CONFIG_UNIX=y
 CONFIG_INET=y
@@ -37,14 +34,18 @@ CONFIG_FB_PXA=y
 # CONFIG_VGA_CONSOLE is not set
 CONFIG_FRAMEBUFFER_CONSOLE=y
 CONFIG_LOGO=y
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=y
+CONFIG_LEDS_TRIGGERS=y
+CONFIG_LEDS_TRIGGER_CPU=y
 CONFIG_EXT2_FS=y
 CONFIG_MSDOS_FS=y
 CONFIG_JFFS2_FS=y
 CONFIG_NFS_FS=y
 CONFIG_ROOT_NFS=y
 CONFIG_NLS_ISO8859_1=y
-CONFIG_MAGIC_SYSRQ=y
 CONFIG_DEBUG_KERNEL=y
-CONFIG_DEBUG_INFO=y
+CONFIG_DEBUG_INFO_DWARF_TOOLCHAIN_DEFAULT=y
+CONFIG_MAGIC_SYSRQ=y
 CONFIG_DEBUG_USER=y
 CONFIG_DEBUG_LL=y
diff --git a/arch/arm/configs/milbeaut_m10v_defconfig b/arch/arm/configs/milbeaut_m10v_defconfig
index 7c07f9893a0f..a2e25bf843cc 100644
--- a/arch/arm/configs/milbeaut_m10v_defconfig
+++ b/arch/arm/configs/milbeaut_m10v_defconfig
@@ -1,5 +1,5 @@
 CONFIG_SYSVIPC=y
-CONFIG_NO_HZ=y
+CONFIG_NO_HZ_IDLE=y
 CONFIG_HIGH_RES_TIMERS=y
 CONFIG_CGROUPS=y
 CONFIG_BLK_DEV_INITRD=y
@@ -26,7 +26,7 @@ CONFIG_THUMB2_KERNEL=y
 # CONFIG_THUMB2_AVOID_R_ARM_THM_JUMP11 is not set
 # CONFIG_ARM_PATCH_IDIV is not set
 CONFIG_HIGHMEM=y
-CONFIG_FORCE_MAX_ZONEORDER=12
+CONFIG_ARCH_FORCE_MAX_ORDER=12
 CONFIG_SECCOMP=y
 CONFIG_KEXEC=y
 CONFIG_EFI=y
@@ -44,9 +44,6 @@ CONFIG_ARM_CPUIDLE=y
 CONFIG_VFP=y
 CONFIG_NEON=y
 CONFIG_KERNEL_MODE_NEON=y
-CONFIG_EFI_VARS=m
-CONFIG_EFI_CAPSULE_LOADER=m
-CONFIG_ARM_CRYPTO=y
 CONFIG_CRYPTO_SHA1_ARM_NEON=m
 CONFIG_CRYPTO_SHA1_ARM_CE=m
 CONFIG_CRYPTO_SHA2_ARM_CE=m
@@ -64,8 +61,7 @@ CONFIG_CMDLINE_PARTITION=y
 CONFIG_CMA=y
 CONFIG_DEVTMPFS=y
 CONFIG_DEVTMPFS_MOUNT=y
-CONFIG_DMA_CMA=y
-CONFIG_CMA_SIZE_MBYTES=64
+CONFIG_EFI_CAPSULE_LOADER=m
 CONFIG_OF_OVERLAY=y
 CONFIG_BLK_DEV_LOOP=y
 CONFIG_BLK_DEV_RAM=y
@@ -115,5 +111,7 @@ CONFIG_CRYPTO_AES=y
 # CONFIG_CRYPTO_HW is not set
 CONFIG_CRC_CCITT=m
 CONFIG_CRC_ITU_T=m
+CONFIG_DMA_CMA=y
+CONFIG_CMA_SIZE_MBYTES=64
 CONFIG_PRINTK_TIME=y
 CONFIG_MAGIC_SYSRQ=y
diff --git a/arch/arm/configs/mini2440_defconfig b/arch/arm/configs/mini2440_defconfig
index 898490aaa39e..86e00f684e16 100644
--- a/arch/arm/configs/mini2440_defconfig
+++ b/arch/arm/configs/mini2440_defconfig
@@ -3,14 +3,15 @@ CONFIG_SYSVIPC=y
 CONFIG_POSIX_MQUEUE=y
 CONFIG_RELAY=y
 CONFIG_BLK_DEV_INITRD=y
-# CONFIG_COMPAT_BRK is not set
+CONFIG_ARCH_MULTI_V4T=y
+# CONFIG_ARCH_MULTI_V7 is not set
 CONFIG_ARCH_S3C24XX=y
 CONFIG_S3C_ADC=y
-CONFIG_S3C24XX_PWM=y
 # CONFIG_CPU_S3C2410 is not set
 CONFIG_CPU_S3C2440=y
 CONFIG_MACH_MINI2440=y
 CONFIG_AEABI=y
+CONFIG_UNUSED_BOARD_FILES=y
 CONFIG_KEXEC=y
 CONFIG_CPU_IDLE=y
 CONFIG_APM_EMULATION=y
@@ -18,7 +19,6 @@ CONFIG_MODULES=y
 CONFIG_MODULE_FORCE_LOAD=y
 CONFIG_MODULE_UNLOAD=y
 CONFIG_MODULE_FORCE_UNLOAD=y
-# CONFIG_BLK_DEV_BSG is not set
 CONFIG_BLK_DEV_INTEGRITY=y
 CONFIG_PARTITION_ADVANCED=y
 CONFIG_BSD_DISKLABEL=y
@@ -27,6 +27,7 @@ CONFIG_SOLARIS_X86_PARTITION=y
 CONFIG_UNIXWARE_DISKLABEL=y
 CONFIG_LDM_PARTITION=y
 CONFIG_BINFMT_MISC=m
+# CONFIG_COMPAT_BRK is not set
 CONFIG_NET=y
 CONFIG_PACKET=y
 CONFIG_UNIX=y
@@ -103,6 +104,7 @@ CONFIG_SCSI=m
 # CONFIG_SCSI_PROC_FS is not set
 CONFIG_BLK_DEV_SD=m
 CONFIG_CHR_DEV_SG=m
+# CONFIG_BLK_DEV_BSG is not set
 # CONFIG_SCSI_LOWLEVEL is not set
 CONFIG_NETDEVICES=y
 CONFIG_TUN=m
@@ -228,6 +230,8 @@ CONFIG_RTC_INTF_DEV_UIE_EMUL=y
 CONFIG_RTC_DRV_S3C=y
 CONFIG_DMADEVICES=y
 CONFIG_S3C24XX_DMAC=y
+CONFIG_PWM=y
+CONFIG_PWM_SAMSUNG=y
 CONFIG_EXT2_FS=m
 CONFIG_EXT2_FS_XATTR=y
 CONFIG_EXT2_FS_POSIX_ACL=y
@@ -325,10 +329,10 @@ CONFIG_LIBCRC32C=m
 CONFIG_FONTS=y
 CONFIG_FONT_8x8=y
 CONFIG_FONT_MINI_4x6=y
-CONFIG_DEBUG_INFO=y
+CONFIG_DEBUG_INFO_DWARF_TOOLCHAIN_DEFAULT=y
 # CONFIG_ENABLE_MUST_CHECK is not set
+CONFIG_DEBUG_KERNEL=y
 CONFIG_STRIP_ASM_SYMS=y
 CONFIG_DEBUG_FS=y
-CONFIG_DEBUG_KERNEL=y
 # CONFIG_SCHED_DEBUG is not set
 CONFIG_DEBUG_USER=y
diff --git a/arch/arm/configs/mmp2_defconfig b/arch/arm/configs/mmp2_defconfig
index a5e8d2235a1a..7984640e994e 100644
--- a/arch/arm/configs/mmp2_defconfig
+++ b/arch/arm/configs/mmp2_defconfig
@@ -1,22 +1,18 @@
 CONFIG_SYSVIPC=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_PREEMPT=y
 CONFIG_LOG_BUF_SHIFT=14
 CONFIG_SYSFS_DEPRECATED_V2=y
-CONFIG_SLAB=y
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
-CONFIG_MODULE_FORCE_UNLOAD=y
 # CONFIG_BLK_DEV_BSG is not set
 CONFIG_ARCH_MMP=y
-CONFIG_MACH_BROWNSTONE=y
-CONFIG_MACH_FLINT=y
-CONFIG_MACH_MARVELL_JASPER=y
-CONFIG_HIGH_RES_TIMERS=y
-CONFIG_PREEMPT=y
 CONFIG_AEABI=y
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_MACH_MMP2_DT=y
 CONFIG_CMDLINE="root=/dev/nfs rootfstype=nfs nfsroot=192.168.1.100:/nfsroot/ ip=192.168.1.101:192.168.1.100::255.255.255.0::eth0:on console=ttyS2,38400 mem=128M user_debug=255 earlyprintk"
 CONFIG_VFP=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_MODULE_FORCE_UNLOAD=y
+CONFIG_SLAB=y
 CONFIG_NET=y
 CONFIG_PACKET=y
 CONFIG_UNIX=y
@@ -28,9 +24,9 @@ CONFIG_IP_PNP=y
 CONFIG_MTD=y
 CONFIG_MTD_CMDLINE_PARTS=y
 CONFIG_MTD_BLOCK=y
-CONFIG_MTD_RAW_NAND=y
 CONFIG_MTD_ONENAND=y
 CONFIG_MTD_ONENAND_GENERIC=y
+CONFIG_MTD_RAW_NAND=y
 # CONFIG_BLK_DEV is not set
 CONFIG_NETDEVICES=y
 CONFIG_NET_ETHERNET=y
@@ -39,9 +35,9 @@ CONFIG_SMC91X=y
 # CONFIG_INPUT_KEYBOARD is not set
 # CONFIG_INPUT_MOUSE is not set
 # CONFIG_SERIO is not set
+# CONFIG_LEGACY_PTYS is not set
 CONFIG_SERIAL_PXA=y
 CONFIG_SERIAL_PXA_CONSOLE=y
-# CONFIG_LEGACY_PTYS is not set
 # CONFIG_HW_RANDOM is not set
 CONFIG_I2C=y
 CONFIG_I2C_PXA=y
@@ -55,17 +51,18 @@ CONFIG_BACKLIGHT_CLASS_DEVICE=y
 CONFIG_BACKLIGHT_MAX8925=y
 # CONFIG_VGA_CONSOLE is not set
 # CONFIG_USB_SUPPORT is not set
+CONFIG_MMC=y
 CONFIG_RTC_CLASS=y
 CONFIG_RTC_DRV_MAX8925=y
-CONFIG_MMC=y
-# CONFIG_DNOTIFY is not set
-CONFIG_TMPFS=y
-CONFIG_TMPFS_POSIX_ACL=y
+# CONFIG_RESET_CONTROLLER is not set
 CONFIG_EXT2_FS=y
 CONFIG_EXT3_FS=y
 CONFIG_EXT4_FS=y
+# CONFIG_DNOTIFY is not set
 CONFIG_MSDOS_FS=y
 CONFIG_FAT_DEFAULT_CODEPAGE=437
+CONFIG_TMPFS=y
+CONFIG_TMPFS_POSIX_ACL=y
 CONFIG_JFFS2_FS=y
 CONFIG_CRAMFS=y
 CONFIG_NFS_FS=y
@@ -73,16 +70,16 @@ CONFIG_NFS_V3=y
 CONFIG_NFS_V3_ACL=y
 CONFIG_NFS_V4=y
 CONFIG_ROOT_NFS=y
+CONFIG_CRC_CCITT=y
 CONFIG_PRINTK_TIME=y
+CONFIG_DEBUG_KERNEL=y
+CONFIG_DEBUG_INFO_DWARF_TOOLCHAIN_DEFAULT=y
 CONFIG_MAGIC_SYSRQ=y
 CONFIG_DEBUG_FS=y
-CONFIG_DEBUG_KERNEL=y
 # CONFIG_DEBUG_PREEMPT is not set
-CONFIG_DEBUG_INFO=y
 # CONFIG_DYNAMIC_DEBUG is not set
 CONFIG_DEBUG_USER=y
 CONFIG_DEBUG_LL=y
 CONFIG_DEBUG_MMP_UART3=y
 CONFIG_EARLY_PRINTK=y
 # CONFIG_CRYPTO_ANSI_CPRNG is not set
-CONFIG_CRC_CCITT=y
diff --git a/arch/arm/configs/moxart_defconfig b/arch/arm/configs/moxart_defconfig
index eacc089d86c5..ea31f116d577 100644
--- a/arch/arm/configs/moxart_defconfig
+++ b/arch/arm/configs/moxart_defconfig
@@ -1,7 +1,7 @@
 # CONFIG_LOCALVERSION_AUTO is not set
-# CONFIG_SWAP is not set
 CONFIG_SYSVIPC=y
-CONFIG_NO_HZ=y
+CONFIG_NO_HZ_IDLE=y
+CONFIG_PREEMPT=y
 CONFIG_IKCONFIG=y
 CONFIG_IKCONFIG_PROC=y
 # CONFIG_ELF_CORE is not set
@@ -11,18 +11,17 @@ CONFIG_IKCONFIG_PROC=y
 # CONFIG_EVENTFD is not set
 # CONFIG_AIO is not set
 CONFIG_EMBEDDED=y
-# CONFIG_VM_EVENT_COUNTERS is not set
-# CONFIG_SLUB_DEBUG is not set
-# CONFIG_COMPAT_BRK is not set
 # CONFIG_BLK_DEV_BSG is not set
 CONFIG_ARCH_MULTI_V4=y
 # CONFIG_ARCH_MULTI_V7 is not set
 CONFIG_ARCH_MOXART=y
 CONFIG_MACH_UC7112LX=y
-CONFIG_PREEMPT=y
 CONFIG_AEABI=y
 # CONFIG_ATAGS is not set
 CONFIG_ARM_APPENDED_DTB=y
+# CONFIG_SWAP is not set
+# CONFIG_COMPAT_BRK is not set
+# CONFIG_VM_EVENT_COUNTERS is not set
 CONFIG_NET=y
 CONFIG_PACKET=y
 CONFIG_UNIX=y
@@ -118,10 +117,15 @@ CONFIG_EXT3_FS=y
 CONFIG_TMPFS=y
 CONFIG_CONFIGFS_FS=y
 CONFIG_JFFS2_FS=y
+CONFIG_KEYS=y
+CONFIG_CRC32_BIT=y
+CONFIG_DMA_API_DEBUG=y
 CONFIG_PRINTK_TIME=y
-CONFIG_DEBUG_INFO=y
+CONFIG_DEBUG_INFO_DWARF_TOOLCHAIN_DEFAULT=y
 # CONFIG_ENABLE_MUST_CHECK is not set
+CONFIG_KGDB=y
 CONFIG_DEBUG_PAGEALLOC=y
+# CONFIG_SLUB_DEBUG is not set
 CONFIG_DEBUG_OBJECTS=y
 CONFIG_DEBUG_KMEMLEAK=y
 CONFIG_DEBUG_STACK_USAGE=y
@@ -131,12 +135,8 @@ CONFIG_DETECT_HUNG_TASK=y
 # CONFIG_SCHED_DEBUG is not set
 # CONFIG_DEBUG_PREEMPT is not set
 CONFIG_PROVE_LOCKING=y
-CONFIG_DMA_API_DEBUG=y
-CONFIG_KGDB=y
 CONFIG_DEBUG_LL=y
 CONFIG_DEBUG_LL_UART_8250=y
 CONFIG_DEBUG_UART_PHYS=0x98200000
 CONFIG_DEBUG_UART_VIRT=0xf9820000
 CONFIG_EARLY_PRINTK=y
-CONFIG_KEYS=y
-CONFIG_CRC32_BIT=y
diff --git a/arch/arm/configs/mps2_defconfig b/arch/arm/configs/mps2_defconfig
index 89f4a6ff30bd..3ed73f184d83 100644
--- a/arch/arm/configs/mps2_defconfig
+++ b/arch/arm/configs/mps2_defconfig
@@ -1,5 +1,6 @@
 CONFIG_NO_HZ_IDLE=y
 CONFIG_HIGH_RES_TIMERS=y
+CONFIG_PREEMPT_VOLUNTARY=y
 CONFIG_LOG_BUF_SHIFT=16
 CONFIG_CC_OPTIMIZE_FOR_SIZE=y
 CONFIG_EXPERT=y
@@ -10,22 +11,17 @@ CONFIG_EXPERT=y
 # CONFIG_SIGNALFD is not set
 # CONFIG_EVENTFD is not set
 # CONFIG_AIO is not set
-# CONFIG_VM_EVENT_COUNTERS is not set
-# CONFIG_SLUB_DEBUG is not set
-# CONFIG_BLOCK is not set
 # CONFIG_MMU is not set
 CONFIG_ARCH_MPS2=y
 CONFIG_SET_MEM_PARAM=y
 CONFIG_DRAM_BASE=0x21000000
 CONFIG_DRAM_SIZE=0x1000000
-CONFIG_PREEMPT_VOLUNTARY=y
 # CONFIG_ATAGS is not set
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
+# CONFIG_SUSPEND is not set
+# CONFIG_BLOCK is not set
 CONFIG_BINFMT_FLAT=y
-CONFIG_BINFMT_SHARED_FLAT=y
 # CONFIG_COREDUMP is not set
-# CONFIG_SUSPEND is not set
+# CONFIG_VM_EVENT_COUNTERS is not set
 CONFIG_NET=y
 CONFIG_PACKET=y
 CONFIG_UNIX=y
@@ -68,9 +64,9 @@ CONFIG_SMSC911X=y
 # CONFIG_SERIO is not set
 # CONFIG_VT is not set
 # CONFIG_LEGACY_PTYS is not set
-CONFIG_SERIAL_NONSTANDARD=y
 CONFIG_SERIAL_MPS2_UART_CONSOLE=y
 CONFIG_SERIAL_MPS2_UART=y
+CONFIG_SERIAL_NONSTANDARD=y
 # CONFIG_HW_RANDOM is not set
 # CONFIG_HWMON is not set
 CONFIG_WATCHDOG=y
@@ -98,9 +94,10 @@ CONFIG_NFS_V4_2=y
 CONFIG_ROOT_NFS=y
 CONFIG_NLS=y
 CONFIG_PRINTK_TIME=y
-CONFIG_DEBUG_INFO=y
 # CONFIG_ENABLE_MUST_CHECK is not set
+# CONFIG_DEBUG_BUGVERBOSE is not set
+CONFIG_DEBUG_INFO_DWARF_TOOLCHAIN_DEFAULT=y
 CONFIG_DEBUG_FS=y
+# CONFIG_SLUB_DEBUG is not set
 # CONFIG_SCHED_DEBUG is not set
-# CONFIG_DEBUG_BUGVERBOSE is not set
 CONFIG_MEMTEST=y
diff --git a/arch/arm/configs/multi_v4t_defconfig b/arch/arm/configs/multi_v4t_defconfig
index e530107be412..e2fd822f741a 100644
--- a/arch/arm/configs/multi_v4t_defconfig
+++ b/arch/arm/configs/multi_v4t_defconfig
@@ -3,7 +3,6 @@ CONFIG_SYSVIPC=y
 CONFIG_LOG_BUF_SHIFT=14
 CONFIG_BLK_DEV_INITRD=y
 CONFIG_EMBEDDED=y
-CONFIG_SLOB=y
 CONFIG_ARCH_MULTI_V4T=y
 # CONFIG_ARCH_MULTI_V7 is not set
 CONFIG_ARCH_AT91=y
@@ -11,23 +10,22 @@ CONFIG_SOC_AT91RM9200=y
 CONFIG_ARCH_CLPS711X=y
 CONFIG_ARCH_MXC=y
 CONFIG_SOC_IMX1=y
+CONFIG_ARCH_NSPIRE=y
 CONFIG_ARCH_INTEGRATOR=y
 CONFIG_ARCH_INTEGRATOR_AP=y
 CONFIG_INTEGRATOR_IMPD1=y
 CONFIG_INTEGRATOR_CM720T=y
 CONFIG_INTEGRATOR_CM920T=y
 CONFIG_INTEGRATOR_CM922T_XA10=y
-CONFIG_ARCH_NSPIRE=y
 CONFIG_AEABI=y
 # CONFIG_ATAGS is not set
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
 CONFIG_CPU_IDLE=y
 CONFIG_ARM_CPUIDLE=y
 CONFIG_ARM_CLPS711X_CPUIDLE=y
 CONFIG_JUMP_LABEL=y
 CONFIG_PARTITION_ADVANCED=y
 # CONFIG_COREDUMP is not set
+CONFIG_SLOB=y
 CONFIG_MTD=y
 CONFIG_MTD_CMDLINE_PARTS=y
 CONFIG_MTD_BLOCK=y
@@ -73,8 +71,6 @@ CONFIG_POWER_RESET_SYSCON_POWEROFF=y
 CONFIG_WATCHDOG=y
 CONFIG_GPIO_WATCHDOG=y
 CONFIG_AT91RM9200_WATCHDOG=y
-CONFIG_REGULATOR=y
-CONFIG_REGULATOR_FIXED_VOLTAGE=y
 CONFIG_REGULATOR_GPIO=y
 CONFIG_FB=y
 CONFIG_FB_CLPS711X=y
diff --git a/arch/arm/configs/multi_v5_defconfig b/arch/arm/configs/multi_v5_defconfig
index fe8d760256a4..60fc52b95690 100644
--- a/arch/arm/configs/multi_v5_defconfig
+++ b/arch/arm/configs/multi_v5_defconfig
@@ -1,5 +1,5 @@
 CONFIG_SYSVIPC=y
-CONFIG_NO_HZ=y
+CONFIG_NO_HZ_IDLE=y
 CONFIG_HIGH_RES_TIMERS=y
 CONFIG_PREEMPT=y
 CONFIG_LOG_BUF_SHIFT=19
@@ -12,23 +12,9 @@ CONFIG_MACH_ASPEED_G4=y
 CONFIG_ARCH_AT91=y
 CONFIG_SOC_AT91SAM9=y
 CONFIG_ARCH_DAVINCI=y
-CONFIG_ARCH_DAVINCI_DM644x=y
-CONFIG_ARCH_DAVINCI_DM355=y
-CONFIG_ARCH_DAVINCI_DM646x=y
 CONFIG_ARCH_DAVINCI_DA830=y
 CONFIG_ARCH_DAVINCI_DA850=y
-CONFIG_ARCH_DAVINCI_DM365=y
-CONFIG_MACH_SFFSDR=y
-CONFIG_MACH_NEUROS_OSD2=y
-CONFIG_MACH_DM355_LEOPARD=y
-CONFIG_MACH_MITYOMAPL138=y
-CONFIG_MACH_OMAPL138_HAWKBOARD=y
 CONFIG_ARCH_MXC=y
-CONFIG_MACH_MX21ADS=y
-CONFIG_MACH_MX27ADS=y
-CONFIG_MACH_MX27_3DS=y
-CONFIG_MACH_IMX27_VISSTRIM_M10=y
-CONFIG_MACH_PCA100=y
 CONFIG_SOC_IMX25=y
 CONFIG_SOC_IMX27=y
 CONFIG_ARCH_MVEBU=y
@@ -36,8 +22,6 @@ CONFIG_MACH_KIRKWOOD=y
 CONFIG_ARCH_NPCM=y
 CONFIG_ARCH_WPCM450=y
 CONFIG_ARCH_ORION5X=y
-CONFIG_MACH_DB88F5281=y
-CONFIG_MACH_RD88F5182=y
 CONFIG_MACH_RD88F5182_DT=y
 CONFIG_MACH_KUROBOX_PRO=y
 CONFIG_MACH_DNS323=y
@@ -45,23 +29,16 @@ CONFIG_MACH_TS209=y
 CONFIG_MACH_TERASTATION_PRO2=y
 CONFIG_MACH_LINKSTATION_PRO=y
 CONFIG_MACH_LINKSTATION_MINI=y
-CONFIG_MACH_LINKSTATION_LS_HGL=y
 CONFIG_MACH_TS409=y
-CONFIG_MACH_WRT350N_V2=y
 CONFIG_MACH_TS78XX=y
 CONFIG_MACH_MV2120=y
 CONFIG_MACH_D2NET_DT=y
 CONFIG_MACH_NET2BIG=y
 CONFIG_MACH_MSS2_DT=y
-CONFIG_MACH_WNR854T=y
-CONFIG_MACH_RD88F5181L_GE=y
-CONFIG_MACH_RD88F5181L_FXO=y
-CONFIG_MACH_RD88F6183AP_GE=y
-CONFIG_ARCH_U300=y
+CONFIG_ARCH_SUNXI=y
+CONFIG_ARCH_VERSATILE=y
 CONFIG_AEABI=y
 CONFIG_HIGHMEM=y
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
 CONFIG_ARM_APPENDED_DTB=y
 CONFIG_ARM_ATAG_DTB_COMPAT=y
 CONFIG_CPU_FREQ=y
@@ -85,6 +62,7 @@ CONFIG_NET_PKTGEN=m
 CONFIG_CFG80211=y
 CONFIG_MAC80211=y
 CONFIG_PCI_MVEBU=y
+CONFIG_PCI_VERSATILE=y
 CONFIG_DEVTMPFS=y
 CONFIG_DEVTMPFS_MOUNT=y
 CONFIG_IMX_WEIM=y
@@ -103,9 +81,9 @@ CONFIG_MTD_RAW_NAND=y
 CONFIG_MTD_NAND_ATMEL=y
 CONFIG_MTD_NAND_ORION=y
 CONFIG_MTD_SPI_NOR=y
-CONFIG_SPI_ASPEED_SMC=y
 CONFIG_MTD_UBI=y
 CONFIG_BLK_DEV_LOOP=y
+CONFIG_VIRTIO_BLK=y
 CONFIG_ATMEL_SSC=m
 CONFIG_EEPROM_AT24=y
 # CONFIG_SCSI_PROC_FS is not set
@@ -143,7 +121,10 @@ CONFIG_SERIAL_8250_RUNTIME_UARTS=6
 CONFIG_SERIAL_8250_EXTENDED=y
 CONFIG_SERIAL_8250_MANY_PORTS=y
 CONFIG_SERIAL_8250_ASPEED_VUART=m
+CONFIG_SERIAL_8250_DW=y
 CONFIG_SERIAL_OF_PLATFORM=y
+CONFIG_SERIAL_AMBA_PL011=y
+CONFIG_SERIAL_AMBA_PL011_CONSOLE=y
 CONFIG_SERIAL_ATMEL=y
 CONFIG_SERIAL_ATMEL_CONSOLE=y
 CONFIG_SERIAL_ATMEL_TTYAT=y
@@ -159,15 +140,15 @@ CONFIG_I2C_ASPEED=m
 CONFIG_I2C_AT91=y
 CONFIG_I2C_IMX=y
 CONFIG_I2C_MV64XXX=y
-CONFIG_I2C_NOMADIK=y
 CONFIG_SPI=y
+CONFIG_SPI_ASPEED_SMC=y
 CONFIG_SPI_ATMEL=y
 CONFIG_SPI_IMX=y
 CONFIG_SPI_ORION=y
+CONFIG_SPI_SUN6I=y
 CONFIG_GPIO_ASPEED=m
 CONFIG_GPIO_ASPEED_SGPIO=y
 CONFIG_GPIO_MXC=y
-CONFIG_POWER_RESET=y
 CONFIG_POWER_RESET_GPIO=y
 CONFIG_POWER_RESET_QNAP=y
 CONFIG_SENSORS_ADT7475=y
@@ -180,14 +161,15 @@ CONFIG_THERMAL=y
 CONFIG_KIRKWOOD_THERMAL=y
 CONFIG_AT91SAM9X_WATCHDOG=y
 CONFIG_ORION_WATCHDOG=y
+CONFIG_SUNXI_WATCHDOG=y
 CONFIG_NPCM7XX_WATCHDOG=y
 CONFIG_IMX2_WDT=y
 CONFIG_MFD_ATMEL_HLCDC=y
-# CONFIG_ABX500_CORE is not set
 CONFIG_REGULATOR=y
 CONFIG_REGULATOR_FIXED_VOLTAGE=y
 CONFIG_MEDIA_SUPPORT=y
 CONFIG_MEDIA_CAMERA_SUPPORT=y
+CONFIG_MEDIA_PLATFORM_SUPPORT=y
 CONFIG_V4L_PLATFORM_DRIVERS=y
 CONFIG_VIDEO_ASPEED=m
 CONFIG_VIDEO_ATMEL_ISI=m
@@ -196,6 +178,7 @@ CONFIG_DRM_ATMEL_HLCDC=m
 CONFIG_DRM_PANEL_SIMPLE=y
 CONFIG_DRM_PANEL_EDP=y
 CONFIG_DRM_ASPEED_GFX=m
+CONFIG_FB=y
 CONFIG_FB_IMX=y
 CONFIG_FB_ATMEL=y
 CONFIG_BACKLIGHT_ATMEL_LCDC=y
@@ -208,7 +191,8 @@ CONFIG_SND_ATMEL_SOC_WM8904=m
 CONFIG_SND_AT91_SOC_SAM9X5_WM8731=m
 CONFIG_SND_KIRKWOOD_SOC=y
 CONFIG_SND_SOC_ALC5623=y
-CONFIG_SND_SOC_WM8731=y
+CONFIG_SND_SOC_WM8731_I2C=y
+CONFIG_SND_SOC_WM8731_SPI=y
 CONFIG_SND_SIMPLE_CARD=y
 CONFIG_HID_DRAGONRISE=y
 CONFIG_HID_GYRATION=y
@@ -249,6 +233,7 @@ CONFIG_MMC_SDHCI_PLTFM=m
 CONFIG_MMC_SDHCI_OF_ASPEED=m
 CONFIG_MMC_ATMELMCI=y
 CONFIG_MMC_MVSDIO=y
+CONFIG_MMC_SUNXI=y
 CONFIG_NEW_LEDS=y
 CONFIG_LEDS_CLASS=y
 CONFIG_LEDS_GPIO=y
@@ -268,6 +253,8 @@ CONFIG_RTC_DRV_ASPEED=m
 CONFIG_DMADEVICES=y
 CONFIG_AT_HDMAC=y
 CONFIG_MV_XOR=y
+CONFIG_VIRTIO_PCI=y
+CONFIG_VIRTIO_MMIO=y
 CONFIG_STAGING=y
 CONFIG_ASPEED_LPC_CTRL=m
 CONFIG_ASPEED_LPC_SNOOP=m
@@ -302,10 +289,10 @@ CONFIG_CRYPTO_PCBC=m
 CONFIG_CRYPTO_DEV_MARVELL_CESA=y
 CONFIG_CRC_CCITT=y
 CONFIG_LIBCRC32C=y
-CONFIG_DEBUG_INFO=y
-CONFIG_DEBUG_FS=y
-CONFIG_MAGIC_SYSRQ=y
 CONFIG_DEBUG_KERNEL=y
+CONFIG_DEBUG_INFO_DWARF_TOOLCHAIN_DEFAULT=y
+CONFIG_MAGIC_SYSRQ=y
+CONFIG_DEBUG_FS=y
 # CONFIG_SCHED_DEBUG is not set
 # CONFIG_DEBUG_PREEMPT is not set
 # CONFIG_FTRACE is not set
diff --git a/arch/arm/configs/multi_v7_defconfig b/arch/arm/configs/multi_v7_defconfig
index c951aeed2138..b61b2e3d116b 100644
--- a/arch/arm/configs/multi_v7_defconfig
+++ b/arch/arm/configs/multi_v7_defconfig
@@ -1,11 +1,12 @@
 CONFIG_SYSVIPC=y
-CONFIG_NO_HZ=y
+CONFIG_NO_HZ_IDLE=y
 CONFIG_HIGH_RES_TIMERS=y
 CONFIG_CGROUPS=y
 CONFIG_BLK_DEV_INITRD=y
 CONFIG_EMBEDDED=y
 CONFIG_PERF_EVENTS=y
 CONFIG_ARCH_VIRT=y
+CONFIG_ARCH_AIROHA=y
 CONFIG_ARCH_ACTIONS=y
 CONFIG_ARCH_ALPINE=y
 CONFIG_ARCH_ARTPEC=y
@@ -17,6 +18,7 @@ CONFIG_SOC_SAMA5D2=y
 CONFIG_SOC_SAMA5D3=y
 CONFIG_SOC_SAMA5D4=y
 CONFIG_SOC_SAMA7G5=y
+CONFIG_SOC_LAN966=y
 CONFIG_ARCH_BCM=y
 CONFIG_ARCH_BCM_CYGNUS=y
 CONFIG_ARCH_BCM_HR2=y
@@ -24,9 +26,14 @@ CONFIG_ARCH_BCM_NSP=y
 CONFIG_ARCH_BCM_5301X=y
 CONFIG_ARCH_BCM_281XX=y
 CONFIG_ARCH_BCM_21664=y
+CONFIG_ARCH_BCM_23550=y
 CONFIG_ARCH_BCM2835=y
-CONFIG_ARCH_BCM_63XX=y
+CONFIG_ARCH_BCM_53573=y
 CONFIG_ARCH_BRCMSTB=y
+CONFIG_ARCH_BCMBCA=y
+CONFIG_ARCH_BCMBCA_CORTEXA7=y
+CONFIG_ARCH_BCMBCA_CORTEXA9=y
+CONFIG_ARCH_BCMBCA_BRAHMAB15=y
 CONFIG_ARCH_BERLIN=y
 CONFIG_MACH_BERLIN_BG2=y
 CONFIG_MACH_BERLIN_BG2CD=y
@@ -39,6 +46,8 @@ CONFIG_ARCH_HI3xxx=y
 CONFIG_ARCH_HIP01=y
 CONFIG_ARCH_HIP04=y
 CONFIG_ARCH_HIX5HD2=y
+CONFIG_ARCH_HPE=y
+CONFIG_ARCH_HPE_GXP=y
 CONFIG_ARCH_MXC=y
 CONFIG_SOC_IMX50=y
 CONFIG_SOC_IMX51=y
@@ -75,6 +84,7 @@ CONFIG_SOC_AM43XX=y
 CONFIG_SOC_DRA7XX=y
 CONFIG_ARCH_QCOM=y
 CONFIG_ARCH_MSM8X60=y
+CONFIG_ARCH_MSM8916=y
 CONFIG_ARCH_MSM8960=y
 CONFIG_ARCH_MSM8974=y
 CONFIG_ARCH_ROCKCHIP=y
@@ -86,6 +96,7 @@ CONFIG_MACH_SPEAR1310=y
 CONFIG_MACH_SPEAR1340=y
 CONFIG_ARCH_STI=y
 CONFIG_ARCH_STM32=y
+CONFIG_ARCH_SUNPLUS=y
 CONFIG_ARCH_SUNXI=y
 CONFIG_ARCH_TEGRA=y
 CONFIG_ARCH_UNIPHIER=y
@@ -109,23 +120,18 @@ CONFIG_CPU_FREQ_GOV_CONSERVATIVE=m
 CONFIG_CPU_FREQ_GOV_SCHEDUTIL=y
 CONFIG_CPUFREQ_DT=y
 CONFIG_ARM_IMX6Q_CPUFREQ=y
+CONFIG_ARM_QCOM_CPUFREQ_NVMEM=y
 CONFIG_ARM_RASPBERRYPI_CPUFREQ=y
 CONFIG_ARM_SCMI_CPUFREQ=y
 CONFIG_QORIQ_CPUFREQ=y
 CONFIG_CPU_IDLE=y
 CONFIG_ARM_CPUIDLE=y
+CONFIG_ARM_PSCI_CPUIDLE=y
 CONFIG_ARM_ZYNQ_CPUIDLE=y
 CONFIG_ARM_EXYNOS_CPUIDLE=y
 CONFIG_ARM_TEGRA_CPUIDLE=y
 CONFIG_ARM_QCOM_SPM_CPUIDLE=y
 CONFIG_KERNEL_MODE_NEON=y
-CONFIG_ARM_SCMI_PROTOCOL=y
-CONFIG_RASPBERRYPI_FIRMWARE=y
-CONFIG_TRUSTED_FOUNDATIONS=y
-CONFIG_BCM47XX_NVRAM=y
-CONFIG_BCM47XX_SPROM=y
-CONFIG_EFI_CAPSULE_LOADER=m
-CONFIG_ARM_CRYPTO=y
 CONFIG_CRYPTO_SHA1_ARM_NEON=m
 CONFIG_CRYPTO_SHA1_ARM_CE=m
 CONFIG_CRYPTO_SHA2_ARM_CE=m
@@ -157,18 +163,15 @@ CONFIG_IPV6_MIP6=m
 CONFIG_IPV6_TUNNEL=m
 CONFIG_IPV6_MULTIPLE_TABLES=y
 CONFIG_NET_DSA=m
+CONFIG_QRTR=m
+CONFIG_QRTR_SMD=m
 CONFIG_CAN=y
-CONFIG_CAN_AT91=m
-CONFIG_CAN_FLEXCAN=m
-CONFIG_CAN_SUN4I=y
-CONFIG_CAN_XILINXCAN=y
-CONFIG_CAN_RCAR=m
-CONFIG_CAN_MCP251X=y
 CONFIG_BT=m
 CONFIG_BT_HCIUART=m
 CONFIG_BT_HCIUART_BCM=y
 CONFIG_BT_MRVL=m
 CONFIG_BT_MRVL_SDIO=m
+CONFIG_BT_QCOMSMD=m
 CONFIG_CFG80211=m
 CONFIG_MAC80211=m
 CONFIG_RFKILL=y
@@ -194,6 +197,12 @@ CONFIG_PCI_EPF_TEST=m
 CONFIG_DEVTMPFS=y
 CONFIG_DEVTMPFS_MOUNT=y
 CONFIG_OMAP_OCP2SCP=y
+CONFIG_ARM_SCMI_PROTOCOL=y
+CONFIG_RASPBERRYPI_FIRMWARE=y
+CONFIG_TRUSTED_FOUNDATIONS=y
+CONFIG_BCM47XX_NVRAM=y
+CONFIG_BCM47XX_SPROM=y
+CONFIG_EFI_CAPSULE_LOADER=m
 CONFIG_MTD=y
 CONFIG_MTD_CMDLINE_PARTS=y
 CONFIG_MTD_BLOCK=y
@@ -214,7 +223,6 @@ CONFIG_MTD_NAND_DAVINCI=y
 CONFIG_MTD_NAND_STM32_FMC2=y
 CONFIG_MTD_NAND_PL35X=y
 CONFIG_MTD_SPI_NOR=y
-CONFIG_SPI_ASPEED_SMC=m
 CONFIG_MTD_UBI=y
 CONFIG_BLK_DEV_LOOP=y
 CONFIG_BLK_DEV_RAM=y
@@ -225,6 +233,7 @@ CONFIG_AD525X_DPOT_I2C=y
 CONFIG_ICS932S401=y
 CONFIG_ATMEL_SSC=m
 CONFIG_QCOM_COINCELL=m
+CONFIG_QCOM_FASTRPC=m
 CONFIG_APDS9802ALS=y
 CONFIG_ISL29003=y
 CONFIG_PCI_ENDPOINT_TEST=m
@@ -244,14 +253,13 @@ CONFIG_SATA_HIGHBANK=y
 CONFIG_SATA_MV=y
 CONFIG_SATA_RCAR=y
 CONFIG_NETDEVICES=y
-CONFIG_NET_VENDOR_ASIX=y
-CONFIG_SPI_AX88796C=m
 CONFIG_VIRTIO_NET=y
 CONFIG_B53_SPI_DRIVER=m
 CONFIG_B53_MDIO_DRIVER=m
 CONFIG_B53_MMAP_DRIVER=m
 CONFIG_NET_DSA_BCM_SF2=m
 CONFIG_SUN4I_EMAC=y
+CONFIG_SPI_AX88796C=m
 CONFIG_BCMGENET=m
 CONFIG_BGMAC_BCMA=y
 CONFIG_SYSTEMPORT=m
@@ -266,6 +274,7 @@ CONFIG_MV643XX_ETH=y
 CONFIG_MVNETA=y
 CONFIG_PXA168_ETH=m
 CONFIG_KS8851=y
+CONFIG_LAN966X_SWITCH=m
 CONFIG_R8169=y
 CONFIG_SH_ETH=y
 CONFIG_SMSC911X=y
@@ -276,18 +285,27 @@ CONFIG_TI_CPSW=y
 CONFIG_TI_CPSW_SWITCHDEV=y
 CONFIG_TI_CPTS=y
 CONFIG_XILINX_EMACLITE=y
+CONFIG_SFP=m
 CONFIG_BROADCOM_PHY=y
 CONFIG_ICPLUS_PHY=y
 CONFIG_MARVELL_PHY=y
 CONFIG_AT803X_PHY=y
 CONFIG_ROCKCHIP_PHY=y
 CONFIG_DP83867_PHY=y
+CONFIG_CAN_AT91=m
+CONFIG_CAN_FLEXCAN=m
+CONFIG_CAN_SUN4I=y
+CONFIG_CAN_XILINXCAN=y
+CONFIG_CAN_RCAR=m
+CONFIG_CAN_MCP251X=y
+CONFIG_MDIO_MSCC_MIIM=m
 CONFIG_USB_PEGASUS=y
 CONFIG_USB_RTL8152=m
 CONFIG_USB_LAN78XX=m
 CONFIG_USB_USBNET=y
 CONFIG_USB_NET_SMSC75XX=y
 CONFIG_USB_NET_SMSC95XX=y
+CONFIG_WCN36XX=m
 CONFIG_BRCMFMAC=m
 CONFIG_MWIFIEX=m
 CONFIG_MWIFIEX_SDIO=m
@@ -316,6 +334,7 @@ CONFIG_TOUCHSCREEN_ST1232=m
 CONFIG_TOUCHSCREEN_STMPE=y
 CONFIG_TOUCHSCREEN_SUN4I=y
 CONFIG_INPUT_MISC=y
+CONFIG_INPUT_PM8941_PWRKEY=y
 CONFIG_INPUT_MAX77693_HAPTIC=m
 CONFIG_INPUT_MAX8997_HAPTIC=m
 CONFIG_INPUT_CPCAP_PWRBUTTON=m
@@ -357,8 +376,6 @@ CONFIG_SERIAL_MSM=y
 CONFIG_SERIAL_MSM_CONSOLE=y
 CONFIG_SERIAL_VT8500=y
 CONFIG_SERIAL_VT8500_CONSOLE=y
-CONFIG_SERIAL_OMAP=y
-CONFIG_SERIAL_OMAP_CONSOLE=y
 CONFIG_SERIAL_BCM63XX=y
 CONFIG_SERIAL_BCM63XX_CONSOLE=y
 CONFIG_SERIAL_XILINX_PS_UART=y
@@ -382,6 +399,7 @@ CONFIG_TCG_TPM=m
 CONFIG_TCG_TIS_I2C_INFINEON=m
 CONFIG_I2C_CHARDEV=y
 CONFIG_I2C_ARB_GPIO_CHALLENGE=m
+CONFIG_I2C_MUX_GPIO=y
 CONFIG_I2C_MUX_PCA954x=y
 CONFIG_I2C_MUX_PINCTRL=y
 CONFIG_I2C_DEMUX_PINCTRL=y
@@ -397,6 +415,8 @@ CONFIG_I2C_IMX=y
 CONFIG_I2C_MESON=y
 CONFIG_I2C_MV64XXX=y
 CONFIG_I2C_OWL=y
+CONFIG_I2C_QCOM_CCI=m
+CONFIG_I2C_QUP=y
 CONFIG_I2C_RIIC=y
 CONFIG_I2C_RK3X=y
 CONFIG_I2C_S3C2410=y
@@ -412,7 +432,9 @@ CONFIG_I2C_RCAR=y
 CONFIG_I2C_CROS_EC_TUNNEL=m
 CONFIG_I2C_SLAVE_EEPROM=y
 CONFIG_SPI=y
+CONFIG_SPI_ASPEED_SMC=m
 CONFIG_SPI_ATMEL=m
+CONFIG_SPI_ATMEL_QUADSPI=m
 CONFIG_SPI_BCM2835=y
 CONFIG_SPI_BCM2835AUX=y
 CONFIG_SPI_CADENCE=y
@@ -425,6 +447,7 @@ CONFIG_SPI_ORION=y
 CONFIG_SPI_PL022=y
 CONFIG_SPI_ROCKCHIP=m
 CONFIG_SPI_RSPI=y
+CONFIG_SPI_QUP=m
 CONFIG_SPI_S3C64XX=m
 CONFIG_SPI_SH_MSIOF=m
 CONFIG_SPI_SH_HSPI=y
@@ -438,10 +461,11 @@ CONFIG_SPI_TEGRA20_SLINK=y
 CONFIG_SPI_XILINX=y
 CONFIG_SPI_SPIDEV=y
 CONFIG_SPMI=y
-CONFIG_PTP_1588_CLOCK=y
 CONFIG_PINCTRL_AS3722=y
-CONFIG_PINCTRL_STMFX=y
+CONFIG_PINCTRL_MICROCHIP_SGPIO=y
+CONFIG_PINCTRL_OCELOT=y
 CONFIG_PINCTRL_PALMAS=y
+CONFIG_PINCTRL_STMFX=y
 CONFIG_PINCTRL_OWL=y
 CONFIG_PINCTRL_S500=y
 CONFIG_PINCTRL_MSM=y
@@ -475,6 +499,8 @@ CONFIG_GPIO_TWL4030=y
 CONFIG_POWER_RESET_AS3722=y
 CONFIG_POWER_RESET_GPIO=y
 CONFIG_POWER_RESET_GPIO_RESTART=y
+CONFIG_POWER_RESET_MSM=y
+CONFIG_POWER_RESET_QCOM_PON=y
 CONFIG_POWER_RESET_ST=y
 CONFIG_POWER_RESET_KEYSTONE=y
 CONFIG_POWER_RESET_RMOBILE=y
@@ -482,7 +508,6 @@ CONFIG_BATTERY_ACT8945A=y
 CONFIG_BATTERY_CPCAP=m
 CONFIG_BATTERY_SBS=y
 CONFIG_BATTERY_BQ27XXX=m
-CONFIG_BATTERY_ACER_A500=m
 CONFIG_AXP20X_POWER=m
 CONFIG_BATTERY_MAX17040=m
 CONFIG_BATTERY_MAX17042=m
@@ -492,10 +517,13 @@ CONFIG_CHARGER_MAX14577=m
 CONFIG_CHARGER_MAX77693=m
 CONFIG_CHARGER_MAX8997=m
 CONFIG_CHARGER_MAX8998=m
+CONFIG_CHARGER_SMB347=m
 CONFIG_CHARGER_TPS65090=y
+CONFIG_BATTERY_ACER_A500=m
 CONFIG_SENSORS_ARM_SCMI=y
 CONFIG_SENSORS_ASPEED=m
 CONFIG_SENSORS_IIO_HWMON=y
+CONFIG_SENSORS_LAN966X=m
 CONFIG_SENSORS_LM90=y
 CONFIG_SENSORS_LM95245=y
 CONFIG_SENSORS_NTC_THERMISTOR=m
@@ -515,6 +543,7 @@ CONFIG_ST_THERMAL_MEMMAP=y
 CONFIG_TEGRA_SOCTHERM=m
 CONFIG_TEGRA30_TSENSOR=m
 CONFIG_GENERIC_ADC_THERMAL=m
+CONFIG_QCOM_TSENS=y
 CONFIG_UNIPHIER_THERMAL=y
 CONFIG_DA9063_WATCHDOG=m
 CONFIG_XILINX_WATCHDOG=y
@@ -530,19 +559,21 @@ CONFIG_SUNXI_WATCHDOG=y
 CONFIG_IMX2_WDT=y
 CONFIG_ST_LPC_WATCHDOG=y
 CONFIG_TEGRA_WATCHDOG=m
+CONFIG_QCOM_WDT=m
 CONFIG_MESON_WATCHDOG=y
 CONFIG_DIGICOLOR_WATCHDOG=y
 CONFIG_RENESAS_WDT=m
 CONFIG_RENESAS_RZAWDT=m
 CONFIG_STPMIC1_WATCHDOG=y
+CONFIG_PM8916_WATCHDOG=m
 CONFIG_BCM47XX_WDT=y
 CONFIG_BCM2835_WDT=y
 CONFIG_BCM_KONA_WDT=y
 CONFIG_BCM7038_WDT=m
+CONFIG_GXP_WATCHDOG=y
 CONFIG_BCMA_HOST_SOC=y
 CONFIG_BCMA_DRIVER_GMAC_CMN=y
 CONFIG_BCMA_DRIVER_GPIO=y
-CONFIG_MFD_ACER_A500_EC=m
 CONFIG_MFD_ACT8945A=y
 CONFIG_MFD_AS3711=y
 CONFIG_MFD_AS3722=y
@@ -575,6 +606,7 @@ CONFIG_MFD_TPS6586X=y
 CONFIG_MFD_TPS65910=y
 CONFIG_MFD_STM32_LPTIMER=m
 CONFIG_MFD_STPMIC1=y
+CONFIG_MFD_ACER_A500_EC=m
 CONFIG_REGULATOR_ACT8865=y
 CONFIG_REGULATOR_ACT8945A=y
 CONFIG_REGULATOR_ANATOP=y
@@ -601,7 +633,8 @@ CONFIG_REGULATOR_PALMAS=y
 CONFIG_REGULATOR_PBIAS=y
 CONFIG_REGULATOR_PWM=y
 CONFIG_REGULATOR_QCOM_RPM=y
-CONFIG_REGULATOR_QCOM_SMD_RPM=m
+CONFIG_REGULATOR_QCOM_SMD_RPM=y
+CONFIG_REGULATOR_QCOM_SPMI=y
 CONFIG_REGULATOR_RK808=y
 CONFIG_REGULATOR_RN5T618=y
 CONFIG_REGULATOR_S2MPA01=m
@@ -628,27 +661,31 @@ CONFIG_MEDIA_SUPPORT=m
 CONFIG_MEDIA_USB_SUPPORT=y
 CONFIG_USB_VIDEO_CLASS=m
 CONFIG_V4L_PLATFORM_DRIVERS=y
-CONFIG_VIDEO_MMP_CAMERA=m
+CONFIG_V4L_MEM2MEM_DRIVERS=y
 CONFIG_VIDEO_ASPEED=m
-CONFIG_VIDEO_STM32_DCMI=m
+CONFIG_VIDEO_ATMEL_ISC=m
+CONFIG_VIDEO_ATMEL_XISC=m
+CONFIG_VIDEO_ATMEL_ISI=m
+CONFIG_VIDEO_MICROCHIP_CSI2DC=m
+CONFIG_VIDEO_MMP_CAMERA=m
+CONFIG_VIDEO_TEGRA_VDE=m
 CONFIG_VIDEO_RENESAS_CEU=m
+CONFIG_VIDEO_RCAR_VIN=m
+CONFIG_VIDEO_RENESAS_FDP1=m
+CONFIG_VIDEO_RENESAS_JPU=m
+CONFIG_VIDEO_RENESAS_VSP1=m
+CONFIG_VIDEO_SAMSUNG_EXYNOS_GSC=m
 CONFIG_VIDEO_SAMSUNG_EXYNOS4_IS=m
 CONFIG_VIDEO_S5P_FIMC=m
 CONFIG_VIDEO_S5P_MIPI_CSIS=m
 CONFIG_VIDEO_EXYNOS_FIMC_LITE=m
 CONFIG_VIDEO_EXYNOS4_FIMC_IS=m
-CONFIG_VIDEO_RCAR_VIN=m
-CONFIG_VIDEO_ATMEL_ISI=m
-CONFIG_V4L_MEM2MEM_DRIVERS=y
 CONFIG_VIDEO_SAMSUNG_S5P_JPEG=m
 CONFIG_VIDEO_SAMSUNG_S5P_MFC=m
-CONFIG_VIDEO_SAMSUNG_EXYNOS_GSC=m
 CONFIG_VIDEO_STI_BDISP=m
-CONFIG_VIDEO_STI_HVA=m
 CONFIG_VIDEO_STI_DELTA=m
-CONFIG_VIDEO_RENESAS_FDP1=m
-CONFIG_VIDEO_RENESAS_JPU=m
-CONFIG_VIDEO_RENESAS_VSP1=m
+CONFIG_VIDEO_STI_HVA=m
+CONFIG_VIDEO_STM32_DCMI=m
 CONFIG_V4L_TEST_DRIVERS=y
 CONFIG_VIDEO_VIVID=m
 CONFIG_VIDEO_ADV7180=m
@@ -659,6 +696,7 @@ CONFIG_IMX_IPUV3_CORE=m
 CONFIG_DRM=y
 # CONFIG_DRM_I2C_CH7006 is not set
 # CONFIG_DRM_I2C_SIL164 is not set
+CONFIG_DRM_I2C_NXP_TDA998X=m
 CONFIG_DRM_NOUVEAU=m
 CONFIG_DRM_EXYNOS=m
 CONFIG_DRM_EXYNOS_FIMD=y
@@ -673,13 +711,13 @@ CONFIG_ROCKCHIP_DW_MIPI_DSI=y
 CONFIG_ROCKCHIP_INNO_HDMI=y
 CONFIG_DRM_ATMEL_HLCDC=m
 CONFIG_DRM_RCAR_DU=m
-CONFIG_DRM_RCAR_LVDS=y
 CONFIG_DRM_SUN4I=m
 CONFIG_DRM_MSM=m
 CONFIG_DRM_FSL_DCU=m
 CONFIG_DRM_TEGRA=y
 CONFIG_DRM_STM=m
 CONFIG_DRM_STM_DSI=m
+CONFIG_DRM_PANEL_LVDS=m
 CONFIG_DRM_PANEL_SIMPLE=y
 CONFIG_DRM_PANEL_EDP=y
 CONFIG_DRM_PANEL_SAMSUNG_LD9040=m
@@ -687,12 +725,16 @@ CONFIG_DRM_PANEL_ORISETECH_OTM8009A=m
 CONFIG_DRM_PANEL_RAYDIUM_RM68200=m
 CONFIG_DRM_PANEL_SAMSUNG_S6E63J0X03=m
 CONFIG_DRM_PANEL_SAMSUNG_S6E8AA0=m
+CONFIG_DRM_PANEL_SHARP_LQ101R1SX01=m
+CONFIG_DRM_DISPLAY_CONNECTOR=m
+CONFIG_DRM_LVDS_CODEC=m
 CONFIG_DRM_NXP_PTN3460=m
 CONFIG_DRM_PARADE_PS8622=m
 CONFIG_DRM_SII902X=m
 CONFIG_DRM_SII9234=m
 CONFIG_DRM_SIMPLE_BRIDGE=m
 CONFIG_DRM_TOSHIBA_TC358764=m
+CONFIG_DRM_TOSHIBA_TC358768=m
 CONFIG_DRM_I2C_ADV7511=m
 CONFIG_DRM_I2C_ADV7511_AUDIO=y
 CONFIG_DRM_STI=m
@@ -701,6 +743,7 @@ CONFIG_DRM_IMX_PARALLEL_DISPLAY=m
 CONFIG_DRM_IMX_TVE=m
 CONFIG_DRM_IMX_LDB=m
 CONFIG_DRM_IMX_HDMI=m
+CONFIG_DRM_V3D=m
 CONFIG_DRM_VC4=m
 CONFIG_DRM_ETNAVIV=m
 CONFIG_DRM_MXSFB=m
@@ -732,10 +775,13 @@ CONFIG_SND_ATMEL_SOC_WM8904=m
 CONFIG_SND_ATMEL_SOC_PDMIC=m
 CONFIG_SND_ATMEL_SOC_I2S=m
 CONFIG_SND_BCM2835_SOC_I2S=m
-CONFIG_SND_SOC_FSL_SAI=m
+CONFIG_SND_IMX_SOC=m
+CONFIG_SND_SOC_FSL_ASOC_CARD=m
 CONFIG_SND_PXA_SOC_SSP=m
 CONFIG_SND_MMP_SOC_SSPA=m
 CONFIG_SND_PXA910_SOC=m
+CONFIG_SND_SOC_QCOM=m
+CONFIG_SND_SOC_APQ8016_SBC=m
 CONFIG_SND_SOC_ROCKCHIP=m
 CONFIG_SND_SOC_ROCKCHIP_SPDIF=m
 CONFIG_SND_SOC_ROCKCHIP_MAX98090=m
@@ -757,6 +803,7 @@ CONFIG_SND_SOC_STM32_DFSDM=m
 CONFIG_SND_SUN4I_CODEC=m
 CONFIG_SND_SOC_TEGRA=m
 CONFIG_SND_SOC_TEGRA20_I2S=m
+CONFIG_SND_SOC_TEGRA20_SPDIF=m
 CONFIG_SND_SOC_TEGRA30_I2S=m
 CONFIG_SND_SOC_TEGRA_RT5640=m
 CONFIG_SND_SOC_TEGRA_WM8753=m
@@ -765,9 +812,13 @@ CONFIG_SND_SOC_TEGRA_WM9712=m
 CONFIG_SND_SOC_TEGRA_TRIMSLICE=m
 CONFIG_SND_SOC_TEGRA_ALC5632=m
 CONFIG_SND_SOC_TEGRA_MAX98090=m
+CONFIG_SND_SOC_DAVINCI_MCASP=m
+CONFIG_SND_SOC_AC97_CODEC=m
 CONFIG_SND_SOC_AK4642=m
 CONFIG_SND_SOC_CPCAP=m
 CONFIG_SND_SOC_CS42L51_I2C=m
+CONFIG_SND_SOC_MSM8916_WCD_ANALOG=m
+CONFIG_SND_SOC_MSM8916_WCD_DIGITAL=m
 CONFIG_SND_SOC_SGTL5000=m
 CONFIG_SND_SOC_STI_SAS=m
 CONFIG_SND_SOC_WM8978=m
@@ -777,6 +828,7 @@ CONFIG_USB_OTG=y
 CONFIG_USB_XHCI_HCD=y
 CONFIG_USB_XHCI_MVEBU=y
 CONFIG_USB_XHCI_TEGRA=m
+CONFIG_USB_BRCMSTB=m
 CONFIG_USB_EHCI_HCD=y
 CONFIG_USB_EHCI_HCD_STI=y
 CONFIG_USB_EHCI_EXYNOS=m
@@ -806,6 +858,7 @@ CONFIG_USB_CHIPIDEA_UDC=y
 CONFIG_USB_CHIPIDEA_HOST=y
 CONFIG_USB_ISP1760=y
 CONFIG_USB_HSIC_USB3503=y
+CONFIG_USB_ONBOARD_HUB=m
 CONFIG_AB8500_USB=y
 CONFIG_KEYSTONE_USB_PHY=m
 CONFIG_NOP_USB_XCEIV=y
@@ -815,7 +868,6 @@ CONFIG_USB_GPIO_VBUS=y
 CONFIG_USB_ISP1301=y
 CONFIG_USB_MXS_PHY=y
 CONFIG_USB_GADGET=y
-CONFIG_USB_FSL_USB2=y
 CONFIG_USB_RENESAS_USBHS_UDC=m
 CONFIG_USB_ASPEED_VHUB=m
 CONFIG_USB_CONFIGFS=m
@@ -881,10 +933,10 @@ CONFIG_LEDS_CLASS_FLASH=m
 CONFIG_LEDS_CPCAP=m
 CONFIG_LEDS_GPIO=y
 CONFIG_LEDS_PWM=y
-CONFIG_LEDS_MAX77693=m
 CONFIG_LEDS_MAX8997=m
 CONFIG_LEDS_ACER_A500=m
 CONFIG_LEDS_TRIGGERS=y
+CONFIG_LEDS_MAX77693=m
 CONFIG_LEDS_TRIGGER_TIMER=y
 CONFIG_LEDS_TRIGGER_ONESHOT=y
 CONFIG_LEDS_TRIGGER_HEARTBEAT=y
@@ -930,6 +982,7 @@ CONFIG_RTC_DRV_AT91SAM9=m
 CONFIG_RTC_DRV_VT8500=y
 CONFIG_RTC_DRV_SUNXI=y
 CONFIG_RTC_DRV_MV=y
+CONFIG_RTC_DRV_PM8XXX=m
 CONFIG_RTC_DRV_TEGRA=y
 CONFIG_RTC_DRV_ST_LPC=y
 CONFIG_RTC_DRV_STM32=y
@@ -952,6 +1005,7 @@ CONFIG_ST_FDMA=m
 CONFIG_STM32_DMA=y
 CONFIG_STM32_DMAMUX=y
 CONFIG_STM32_MDMA=y
+CONFIG_TEGRA20_APB_DMA=y
 CONFIG_UNIPHIER_MDMAC=y
 CONFIG_XILINX_DMA=y
 CONFIG_QCOM_BAM_DMA=y
@@ -974,29 +1028,54 @@ CONFIG_CROS_EC_SPI=m
 CONFIG_COMMON_CLK_MAX77686=y
 CONFIG_COMMON_CLK_RK808=m
 CONFIG_COMMON_CLK_SCMI=y
+CONFIG_COMMON_CLK_LAN966X=y
 CONFIG_COMMON_CLK_S2MPS11=m
 CONFIG_CLK_RASPBERRYPI=y
 CONFIG_COMMON_CLK_QCOM=y
+CONFIG_QCOM_A53PLL=y
+CONFIG_QCOM_CLK_APCS_MSM8916=y
 CONFIG_QCOM_CLK_RPM=y
+CONFIG_QCOM_CLK_SMD_RPM=y
 CONFIG_APQ_MMCC_8084=y
 CONFIG_MSM_GCC_8660=y
+CONFIG_MSM_GCC_8916=y
 CONFIG_MSM_MMCC_8960=y
 CONFIG_MSM_MMCC_8974=y
-CONFIG_MICROCHIP_PIT64B=y
+CONFIG_HWSPINLOCK=y
+CONFIG_HWSPINLOCK_QCOM=y
 CONFIG_BCM2835_MBOX=y
+CONFIG_QCOM_APCS_IPC=y
+CONFIG_QCOM_IPCC=y
 CONFIG_ROCKCHIP_IOMMU=y
 CONFIG_TEGRA_IOMMU_GART=y
 CONFIG_TEGRA_IOMMU_SMMU=y
 CONFIG_EXYNOS_IOMMU=y
+CONFIG_QCOM_IOMMU=y
 CONFIG_REMOTEPROC=y
+CONFIG_QCOM_Q6V5_MSS=m
+CONFIG_QCOM_SYSMON=m
+CONFIG_QCOM_WCNSS_PIL=m
 CONFIG_ST_REMOTEPROC=m
+CONFIG_RPMSG_QCOM_SMD=y
 CONFIG_RPMSG_VIRTIO=m
 CONFIG_ASPEED_LPC_CTRL=m
 CONFIG_ASPEED_LPC_SNOOP=m
 CONFIG_ASPEED_P2A_CTRL=m
 CONFIG_RASPBERRYPI_POWER=y
+CONFIG_QCOM_COMMAND_DB=m
+CONFIG_QCOM_CPR=y
 CONFIG_QCOM_GSBI=y
-CONFIG_QCOM_SMD_RPM=m
+CONFIG_QCOM_OCMEM=m
+CONFIG_QCOM_RMTFS_MEM=m
+CONFIG_QCOM_RPMH=y
+CONFIG_QCOM_RPMHPD=y
+CONFIG_QCOM_RPMPD=y
+CONFIG_QCOM_SMEM=y
+CONFIG_QCOM_SMD_RPM=y
+CONFIG_QCOM_SMP2P=y
+CONFIG_QCOM_SMSM=y
+CONFIG_QCOM_SOCINFO=m
+CONFIG_QCOM_STATS=m
 CONFIG_QCOM_WCNSS_CTRL=m
 CONFIG_ARCH_EMEV2=y
 CONFIG_ARCH_R8A7794=y
@@ -1029,6 +1108,7 @@ CONFIG_DEVFREQ_EVENT_EXYNOS_NOCP=m
 CONFIG_EXTCON_MAX14577=m
 CONFIG_EXTCON_MAX77693=m
 CONFIG_EXTCON_MAX8997=m
+CONFIG_EXTCON_USB_GPIO=y
 CONFIG_TI_AEMIF=y
 CONFIG_STM32_FMC2_EBI=y
 CONFIG_EXYNOS5422_DMC=m
@@ -1041,6 +1121,7 @@ CONFIG_BERLIN2_ADC=m
 CONFIG_CPCAP_ADC=m
 CONFIG_EXYNOS_ADC=m
 CONFIG_MESON_SARADC=m
+CONFIG_QCOM_SPMI_VADC=m
 CONFIG_ROCKCHIP_SARADC=m
 CONFIG_STM32_ADC_CORE=m
 CONFIG_STM32_ADC=m
@@ -1078,14 +1159,18 @@ CONFIG_PWM_SUN4I=y
 CONFIG_PWM_TEGRA=y
 CONFIG_PWM_VT8500=y
 CONFIG_KEYSTONE_IRQ=y
+CONFIG_RESET_MCHP_SPARX5=y
 CONFIG_PHY_SUN4I_USB=y
 CONFIG_PHY_SUN9I_USB=y
+CONFIG_PHY_BRCM_USB=m
 CONFIG_PHY_HIX5HD2_SATA=y
 CONFIG_PHY_BERLIN_SATA=y
 CONFIG_PHY_BERLIN_USB=y
 CONFIG_PHY_MMP3_USB=m
+CONFIG_PHY_LAN966X_SERDES=m
 CONFIG_PHY_CPCAP_USB=m
 CONFIG_PHY_QCOM_APQ8064_SATA=m
+CONFIG_PHY_QCOM_USB_HS=y
 CONFIG_PHY_RCAR_GEN2=m
 CONFIG_PHY_ROCKCHIP_DP=m
 CONFIG_PHY_ROCKCHIP_USB=y
@@ -1103,10 +1188,11 @@ CONFIG_TI_PIPE3=y
 CONFIG_TWL4030_USB=m
 CONFIG_RAS=y
 CONFIG_NVMEM_IMX_OCOTP=y
-CONFIG_ROCKCHIP_EFUSE=m
+CONFIG_NVMEM_QCOM_QFPROM=y
+CONFIG_NVMEM_ROCKCHIP_EFUSE=m
 CONFIG_NVMEM_SUNXI_SID=y
 CONFIG_NVMEM_VF610_OCOTP=y
-CONFIG_MESON_MX_EFUSE=m
+CONFIG_NVMEM_MESON_MX_EFUSE=m
 CONFIG_NVMEM_RMEM=m
 CONFIG_FSI=m
 CONFIG_FSI_MASTER_GPIO=m
@@ -1115,6 +1201,8 @@ CONFIG_FSI_MASTER_ASPEED=m
 CONFIG_FSI_SCOM=m
 CONFIG_FSI_SBEFIFO=m
 CONFIG_FSI_OCC=m
+CONFIG_INTERCONNECT_QCOM=y
+CONFIG_INTERCONNECT_QCOM_MSM8916=y
 CONFIG_COUNTER=m
 CONFIG_STM32_TIMER_CNT=m
 CONFIG_STM32_LPTIMER_CNT=m
@@ -1154,6 +1242,8 @@ CONFIG_CRYPTO_DEV_ATMEL_AES=m
 CONFIG_CRYPTO_DEV_ATMEL_TDES=m
 CONFIG_CRYPTO_DEV_ATMEL_SHA=m
 CONFIG_CRYPTO_DEV_MARVELL_CESA=m
+CONFIG_CRYPTO_DEV_QCE=m
+CONFIG_CRYPTO_DEV_QCOM_RNG=m
 CONFIG_CRYPTO_DEV_ROCKCHIP=m
 CONFIG_CRYPTO_DEV_STM32_CRC=m
 CONFIG_CRYPTO_DEV_STM32_HASH=m
diff --git a/arch/arm/configs/mv78xx0_defconfig b/arch/arm/configs/mv78xx0_defconfig
index cd703c15798f..877c5150a987 100644
--- a/arch/arm/configs/mv78xx0_defconfig
+++ b/arch/arm/configs/mv78xx0_defconfig
@@ -1,14 +1,12 @@
 CONFIG_SYSVIPC=y
+CONFIG_NO_HZ_IDLE=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_PREEMPT=y
 CONFIG_LOG_BUF_SHIFT=14
 CONFIG_SYSFS_DEPRECATED_V2=y
 CONFIG_EXPERT=y
 CONFIG_KALLSYMS_ALL=y
-# CONFIG_SLUB_DEBUG is not set
 CONFIG_PROFILING=y
-CONFIG_KPROBES=y
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
-# CONFIG_BLK_DEV_BSG is not set
 CONFIG_ARCH_MULTI_V5=y
 # CONFIG_ARCH_MULTI_V6 is not set
 # CONFIG_ARCH_MULTI_V7 is not set
@@ -16,15 +14,16 @@ CONFIG_ARCH_MV78XX0=y
 CONFIG_MACH_DB78X00_BP=y
 CONFIG_MACH_RD78X00_MASA=y
 CONFIG_MACH_TERASTATION_WXL=y
-CONFIG_NO_HZ=y
-CONFIG_HIGH_RES_TIMERS=y
-CONFIG_PREEMPT=y
 CONFIG_AEABI=y
 CONFIG_HIGHMEM=y
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
 CONFIG_FPE_NWFPE=y
+CONFIG_UNUSED_BOARD_FILES=y
 CONFIG_VFP=y
+CONFIG_KPROBES=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_PARTITION_ADVANCED=y
+CONFIG_BSD_DISKLABEL=y
 CONFIG_NET=y
 CONFIG_PACKET=y
 CONFIG_UNIX=y
@@ -52,25 +51,26 @@ CONFIG_BLK_DEV_LOOP=y
 CONFIG_BLK_DEV_SD=y
 CONFIG_BLK_DEV_SR=m
 CONFIG_CHR_DEV_SG=m
+# CONFIG_BLK_DEV_BSG is not set
 CONFIG_ATA=y
 CONFIG_SATA_MV=y
 CONFIG_NETDEVICES=y
-CONFIG_MARVELL_PHY=y
 CONFIG_NET_ETHERNET=y
 CONFIG_MII=y
 CONFIG_NET_PCI=y
 CONFIG_MV643XX_ETH=y
 # CONFIG_INPUT_MOUSEDEV is not set
+CONFIG_MARVELL_PHY=y
 CONFIG_INPUT_EVDEV=y
 # CONFIG_INPUT_KEYBOARD is not set
 # CONFIG_INPUT_MOUSE is not set
 # CONFIG_SERIO is not set
 # CONFIG_VT is not set
+CONFIG_LEGACY_PTY_COUNT=16
 CONFIG_SERIAL_8250=y
 CONFIG_SERIAL_8250_CONSOLE=y
 # CONFIG_SERIAL_8250_PCI is not set
 CONFIG_SERIAL_8250_RUNTIME_UARTS=2
-CONFIG_LEGACY_PTY_COUNT=16
 # CONFIG_HW_RANDOM is not set
 CONFIG_I2C=y
 CONFIG_I2C_CHARDEV=y
@@ -110,21 +110,20 @@ CONFIG_CRAMFS=y
 CONFIG_NFS_FS=y
 CONFIG_NFS_V3=y
 CONFIG_ROOT_NFS=y
-CONFIG_PARTITION_ADVANCED=y
-CONFIG_BSD_DISKLABEL=y
 CONFIG_NLS_CODEPAGE_437=y
 CONFIG_NLS_CODEPAGE_850=y
 CONFIG_NLS_ISO8859_1=y
 CONFIG_NLS_ISO8859_2=y
+CONFIG_CRYPTO_CBC=m
+CONFIG_CRYPTO_ECB=m
+CONFIG_CRYPTO_PCBC=m
+# CONFIG_DEBUG_BUGVERBOSE is not set
 CONFIG_MAGIC_SYSRQ=y
 CONFIG_DEBUG_FS=y
 CONFIG_DEBUG_KERNEL=y
+# CONFIG_SLUB_DEBUG is not set
 CONFIG_SCHEDSTATS=y
-# CONFIG_DEBUG_BUGVERBOSE is not set
-CONFIG_DEBUG_INFO=y
+CONFIG_DEBUG_INFO_DWARF_TOOLCHAIN_DEFAULT=y
 CONFIG_DEBUG_USER=y
 CONFIG_DEBUG_LL=y
-CONFIG_CRYPTO_CBC=m
-CONFIG_CRYPTO_ECB=m
-CONFIG_CRYPTO_PCBC=m
 # CONFIG_CRYPTO_ANSI_CPRNG is not set
diff --git a/arch/arm/configs/mvebu_v5_defconfig b/arch/arm/configs/mvebu_v5_defconfig
index d57ff30dabff..2467afd32146 100644
--- a/arch/arm/configs/mvebu_v5_defconfig
+++ b/arch/arm/configs/mvebu_v5_defconfig
@@ -1,19 +1,14 @@
 CONFIG_SYSVIPC=y
 CONFIG_FHANDLE=y
-CONFIG_NO_HZ=y
+CONFIG_NO_HZ_IDLE=y
 CONFIG_HIGH_RES_TIMERS=y
+CONFIG_PREEMPT=y
 CONFIG_LOG_BUF_SHIFT=19
 CONFIG_PROFILING=y
-CONFIG_KPROBES=y
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
-# CONFIG_BLK_DEV_BSG is not set
 # CONFIG_ARCH_MULTI_V7 is not set
 CONFIG_ARCH_MVEBU=y
 CONFIG_MACH_KIRKWOOD=y
 CONFIG_ARCH_ORION5X=y
-CONFIG_MACH_DB88F5281=y
-CONFIG_MACH_RD88F5182=y
 CONFIG_MACH_RD88F5182_DT=y
 CONFIG_MACH_KUROBOX_PRO=y
 CONFIG_MACH_DNS323=y
@@ -22,24 +17,14 @@ CONFIG_MACH_TERASTATION_PRO2=y
 CONFIG_MACH_LINKSTATION_PRO=y
 CONFIG_MACH_LINKSTATION_LSCHL=y
 CONFIG_MACH_LINKSTATION_MINI=y
-CONFIG_MACH_LINKSTATION_LS_HGL=y
 CONFIG_MACH_TS409=y
-CONFIG_MACH_WRT350N_V2=y
 CONFIG_MACH_TS78XX=y
 CONFIG_MACH_MV2120=y
 CONFIG_MACH_D2NET_DT=y
 CONFIG_MACH_NET2BIG=y
 CONFIG_MACH_MSS2_DT=y
-CONFIG_MACH_WNR854T=y
-CONFIG_MACH_RD88F5181L_GE=y
-CONFIG_MACH_RD88F5181L_FXO=y
-CONFIG_MACH_RD88F6183AP_GE=y
-CONFIG_PCI_MVEBU=y
-CONFIG_PREEMPT=y
 CONFIG_AEABI=y
 CONFIG_HIGHMEM=y
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
 CONFIG_ARM_APPENDED_DTB=y
 CONFIG_ARM_ATAG_DTB_COMPAT=y
 CONFIG_CPU_FREQ=y
@@ -47,6 +32,9 @@ CONFIG_CPU_FREQ_STAT=y
 CONFIG_CPU_FREQ_DEFAULT_GOV_ONDEMAND=y
 CONFIG_CPU_IDLE=y
 CONFIG_ARM_KIRKWOOD_CPUIDLE=y
+CONFIG_KPROBES=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
 CONFIG_NET=y
 CONFIG_PACKET=y
 CONFIG_UNIX=y
@@ -61,6 +49,7 @@ CONFIG_NET_SWITCHDEV=y
 CONFIG_NET_PKTGEN=m
 CONFIG_CFG80211=y
 CONFIG_MAC80211=y
+CONFIG_PCI_MVEBU=y
 CONFIG_DEVTMPFS=y
 CONFIG_DEVTMPFS_MOUNT=y
 CONFIG_MTD=y
@@ -84,6 +73,7 @@ CONFIG_EEPROM_AT24=y
 CONFIG_BLK_DEV_SD=y
 CONFIG_BLK_DEV_SR=m
 CONFIG_CHR_DEV_SG=m
+# CONFIG_BLK_DEV_BSG is not set
 CONFIG_ATA=y
 CONFIG_SATA_AHCI=y
 CONFIG_SATA_MV=y
@@ -93,9 +83,9 @@ CONFIG_NET_DSA_MV88E6XXX=y
 CONFIG_MV643XX_ETH=y
 CONFIG_R8169=y
 CONFIG_MARVELL_PHY=y
-CONFIG_MWL8K=m
 CONFIG_LIBERTAS=y
 CONFIG_LIBERTAS_SDIO=y
+CONFIG_MWL8K=m
 CONFIG_INPUT_EVDEV=y
 CONFIG_KEYBOARD_GPIO=y
 # CONFIG_INPUT_MOUSE is not set
@@ -194,16 +184,16 @@ CONFIG_NLS_CODEPAGE_850=y
 CONFIG_NLS_ISO8859_1=y
 CONFIG_NLS_ISO8859_2=y
 CONFIG_NLS_UTF8=y
-CONFIG_DEBUG_INFO=y
-CONFIG_DEBUG_FS=y
-CONFIG_MAGIC_SYSRQ=y
+CONFIG_CRYPTO_CBC=m
+CONFIG_CRYPTO_PCBC=m
+CONFIG_CRYPTO_DEV_MARVELL_CESA=y
+CONFIG_CRC_CCITT=y
+CONFIG_LIBCRC32C=y
 CONFIG_DEBUG_KERNEL=y
+CONFIG_DEBUG_INFO_DWARF_TOOLCHAIN_DEFAULT=y
+CONFIG_MAGIC_SYSRQ=y
+CONFIG_DEBUG_FS=y
 # CONFIG_SCHED_DEBUG is not set
 # CONFIG_DEBUG_PREEMPT is not set
 # CONFIG_FTRACE is not set
 CONFIG_DEBUG_USER=y
-CONFIG_CRYPTO_DEV_MARVELL_CESA=y
-CONFIG_CRYPTO_CBC=m
-CONFIG_CRYPTO_PCBC=m
-CONFIG_CRC_CCITT=y
-CONFIG_LIBCRC32C=y
diff --git a/arch/arm/configs/mvebu_v7_defconfig b/arch/arm/configs/mvebu_v7_defconfig
index 7b713c083a2a..68a18264f31b 100644
--- a/arch/arm/configs/mvebu_v7_defconfig
+++ b/arch/arm/configs/mvebu_v7_defconfig
@@ -4,7 +4,6 @@ CONFIG_LOG_BUF_SHIFT=14
 CONFIG_BLK_DEV_INITRD=y
 CONFIG_EXPERT=y
 CONFIG_PERF_EVENTS=y
-CONFIG_SLAB=y
 CONFIG_ARCH_MVEBU=y
 CONFIG_MACH_ARMADA_370=y
 CONFIG_MACH_ARMADA_375=y
@@ -24,6 +23,7 @@ CONFIG_VFP=y
 CONFIG_NEON=y
 CONFIG_MODULES=y
 CONFIG_MODULE_UNLOAD=y
+CONFIG_SLAB=y
 # CONFIG_COMPACTION is not set
 CONFIG_NET=y
 CONFIG_PACKET=y
@@ -147,7 +147,7 @@ CONFIG_NLS_UTF8=y
 CONFIG_CRYPTO_DEV_MARVELL_CESA=y
 CONFIG_PRINTK_TIME=y
 # CONFIG_DEBUG_BUGVERBOSE is not set
-CONFIG_DEBUG_INFO=y
+CONFIG_DEBUG_INFO_DWARF_TOOLCHAIN_DEFAULT=y
 CONFIG_MAGIC_SYSRQ=y
 # CONFIG_SCHED_DEBUG is not set
 CONFIG_DEBUG_USER=y
diff --git a/arch/arm/configs/mxs_defconfig b/arch/arm/configs/mxs_defconfig
index ca32446b187f..feb38a94c1a7 100644
--- a/arch/arm/configs/mxs_defconfig
+++ b/arch/arm/configs/mxs_defconfig
@@ -1,5 +1,5 @@
 CONFIG_SYSVIPC=y
-CONFIG_NO_HZ=y
+CONFIG_NO_HZ_IDLE=y
 CONFIG_HIGH_RES_TIMERS=y
 CONFIG_PREEMPT_VOLUNTARY=y
 CONFIG_TASKSTATS=y
@@ -15,7 +15,6 @@ CONFIG_CGROUPS=y
 # CONFIG_NET_NS is not set
 CONFIG_BLK_DEV_INITRD=y
 CONFIG_PERF_EVENTS=y
-# CONFIG_COMPAT_BRK is not set
 # CONFIG_ARCH_MULTI_V7 is not set
 CONFIG_ARCH_MXS=y
 CONFIG_AEABI=y
@@ -25,6 +24,7 @@ CONFIG_MODULE_UNLOAD=y
 CONFIG_MODULE_FORCE_UNLOAD=y
 CONFIG_MODVERSIONS=y
 CONFIG_BLK_DEV_INTEGRITY=y
+# CONFIG_COMPAT_BRK is not set
 CONFIG_NET=y
 CONFIG_PACKET=y
 CONFIG_UNIX=y
@@ -38,7 +38,6 @@ CONFIG_SYN_COOKIES=y
 # CONFIG_INET_DIAG is not set
 # CONFIG_IPV6 is not set
 CONFIG_CAN=m
-CONFIG_CAN_FLEXCAN=m
 # CONFIG_WIRELESS is not set
 CONFIG_DEVTMPFS=y
 CONFIG_DEVTMPFS_MOUNT=y
@@ -62,6 +61,7 @@ CONFIG_ICPLUS_PHY=y
 CONFIG_MICREL_PHY=y
 CONFIG_REALTEK_PHY=y
 CONFIG_SMSC_PHY=y
+CONFIG_CAN_FLEXCAN=m
 CONFIG_USB_USBNET=y
 CONFIG_USB_NET_SMSC95XX=y
 # CONFIG_WLAN is not set
@@ -93,6 +93,7 @@ CONFIG_REGULATOR_FIXED_VOLTAGE=y
 CONFIG_DRM=y
 CONFIG_DRM_PANEL_SEIKO_43WVF1G=y
 CONFIG_DRM_MXSFB=y
+CONFIG_FB=y
 CONFIG_FB_MODE_HELPERS=y
 CONFIG_LCD_CLASS_DEVICE=y
 CONFIG_BACKLIGHT_CLASS_DEVICE=y
@@ -162,10 +163,10 @@ CONFIG_CRC_ITU_T=m
 CONFIG_CRC7=m
 CONFIG_FONTS=y
 CONFIG_PRINTK_TIME=y
-CONFIG_DEBUG_INFO=y
+CONFIG_DEBUG_KERNEL=y
+CONFIG_DEBUG_INFO_DWARF_TOOLCHAIN_DEFAULT=y
 CONFIG_FRAME_WARN=2048
 CONFIG_MAGIC_SYSRQ=y
-CONFIG_DEBUG_KERNEL=y
 CONFIG_SOFTLOCKUP_DETECTOR=y
 CONFIG_PROVE_LOCKING=y
 CONFIG_BLK_DEV_IO_TRACE=y
diff --git a/arch/arm/configs/neponset_defconfig b/arch/arm/configs/neponset_defconfig
index 018a1092d0e7..c333406ce5e3 100644
--- a/arch/arm/configs/neponset_defconfig
+++ b/arch/arm/configs/neponset_defconfig
@@ -1,31 +1,32 @@
 CONFIG_SYSVIPC=y
 CONFIG_LOG_BUF_SHIFT=14
 CONFIG_BLK_DEV_INITRD=y
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
+CONFIG_ARCH_MULTI_V4=y
+# CONFIG_ARCH_MULTI_V7 is not set
 CONFIG_ARCH_SA1100=y
 CONFIG_SA1100_ASSABET=y
 CONFIG_ASSABET_NEPONSET=y
-CONFIG_PCCARD=y
-CONFIG_PCMCIA_SA1100=y
-CONFIG_PCMCIA_SA1111=y
-CONFIG_LEDS=y
-CONFIG_LEDS_CPU=y
 CONFIG_ZBOOT_ROM_TEXT=0x80000
 CONFIG_ZBOOT_ROM_BSS=0xc1000000
 CONFIG_ZBOOT_ROM=y
 CONFIG_CMDLINE="console=ttySA0,38400n8 cpufreq=221200 rw root=/dev/mtdblock2 mtdparts=sa1100:512K(boot),1M(kernel),2560K(initrd),4M(root) load_ramdisk=1 prompt_ramdisk=0 mem=32M noinitrd initrd=0xc0800000,3M"
 CONFIG_FPE_NWFPE=y
-CONFIG_BINFMT_AOUT=y
 CONFIG_PM=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_PARTITION_ADVANCED=y
+# CONFIG_MSDOS_PARTITION is not set
 CONFIG_NET=y
 CONFIG_PACKET=y
 CONFIG_UNIX=y
 CONFIG_INET=y
 # CONFIG_IPV6 is not set
+CONFIG_PCCARD=y
+CONFIG_PCMCIA_SA1100=y
+CONFIG_PCMCIA_SA1111=y
 CONFIG_MTD=y
-CONFIG_MTD_REDBOOT_PARTS=y
 CONFIG_MTD_CMDLINE_PARTS=y
+CONFIG_MTD_REDBOOT_PARTS=y
 CONFIG_MTD_BLOCK=y
 CONFIG_MTD_CFI=y
 CONFIG_MTD_CFI_ADV_OPTIONS=y
@@ -39,20 +40,20 @@ CONFIG_BLK_DEV_SD=m
 CONFIG_NETDEVICES=y
 CONFIG_NET_ETHERNET=y
 CONFIG_NET_VENDOR_SMC=y
+CONFIG_PCMCIA_PCNET=y
 CONFIG_SMC9194=y
 CONFIG_SMC91X=y
 CONFIG_NET_PCMCIA=y
-CONFIG_PCMCIA_PCNET=y
 # CONFIG_INPUT_MOUSE is not set
 CONFIG_INPUT_TOUCHSCREEN=y
 CONFIG_SERIO_SERPORT=m
 CONFIG_SERIO_SA1111=y
-CONFIG_SERIAL_NONSTANDARD=y
+CONFIG_LEGACY_PTY_COUNT=64
 CONFIG_SERIAL_8250=y
 CONFIG_SERIAL_8250_CS=y
 CONFIG_SERIAL_SA1100=y
 CONFIG_SERIAL_SA1100_CONSOLE=y
-CONFIG_LEGACY_PTY_COUNT=64
+CONFIG_SERIAL_NONSTANDARD=y
 CONFIG_I2C=y
 CONFIG_I2C_CHARDEV=y
 CONFIG_WATCHDOG=y
@@ -68,17 +69,19 @@ CONFIG_USB=m
 CONFIG_USB_MON=m
 CONFIG_USB_OHCI_HCD=m
 CONFIG_USB_STORAGE=m
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=y
+CONFIG_LEDS_TRIGGERS=y
+CONFIG_LEDS_TRIGGER_CPU=y
 CONFIG_EXT2_FS=y
 CONFIG_MSDOS_FS=m
 CONFIG_VFAT_FS=m
 CONFIG_JFFS2_FS=y
 CONFIG_NFS_FS=y
-CONFIG_PARTITION_ADVANCED=y
-# CONFIG_MSDOS_PARTITION is not set
 CONFIG_NLS=y
 CONFIG_NLS_CODEPAGE_437=m
 CONFIG_NLS_ISO8859_1=m
-CONFIG_MAGIC_SYSRQ=y
 CONFIG_DEBUG_KERNEL=y
+CONFIG_MAGIC_SYSRQ=y
 CONFIG_DEBUG_USER=y
 CONFIG_DEBUG_LL=y
diff --git a/arch/arm/configs/netwinder_defconfig b/arch/arm/configs/netwinder_defconfig
index 2e3b20ef0db1..30ff6fbce5a3 100644
--- a/arch/arm/configs/netwinder_defconfig
+++ b/arch/arm/configs/netwinder_defconfig
@@ -1,15 +1,13 @@
 CONFIG_SYSVIPC=y
 CONFIG_LOG_BUF_SHIFT=14
+CONFIG_ARCH_MULTI_V4=y
+# CONFIG_ARCH_MULTI_V7 is not set
 CONFIG_ARCH_FOOTBRIDGE=y
 CONFIG_ARCH_NETWINDER=y
-CONFIG_LEDS=y
-CONFIG_LEDS_CPU=y
 CONFIG_DEPRECATED_PARAM_STRUCT=y
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
 CONFIG_CMDLINE="root=0x801"
 CONFIG_FPE_NWFPE=y
-CONFIG_BINFMT_AOUT=y
+CONFIG_PARTITION_ADVANCED=y
 CONFIG_NET=y
 CONFIG_PACKET=y
 CONFIG_UNIX=y
@@ -51,9 +49,6 @@ CONFIG_977_WATCHDOG=y
 CONFIG_FB=y
 CONFIG_FB_CYBER2000=y
 CONFIG_FRAMEBUFFER_CONSOLE=y
-CONFIG_FONTS=y
-CONFIG_FONT_8x8=y
-CONFIG_FONT_8x16=y
 CONFIG_LOGO=y
 CONFIG_SOUND=y
 CONFIG_SOUND_PRIME=y
@@ -62,6 +57,10 @@ CONFIG_SOUND_TRACEINIT=y
 CONFIG_SOUND_DMAP=y
 CONFIG_SOUND_YM3812=y
 CONFIG_SOUND_WAVEARTIST=y
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=y
+CONFIG_LEDS_TRIGGERS=y
+CONFIG_LEDS_TRIGGER_CPU=y
 CONFIG_EXT2_FS=y
 CONFIG_ISO9660_FS=y
 CONFIG_JOLIET=y
@@ -71,9 +70,7 @@ CONFIG_NFS_V3=y
 CONFIG_NFS_V4=y
 CONFIG_ROOT_NFS=y
 CONFIG_NFSD=y
-CONFIG_NFSD_V3=y
 CONFIG_SMB_FS=y
-CONFIG_PARTITION_ADVANCED=y
 CONFIG_NLS_CODEPAGE_437=y
 CONFIG_NLS_CODEPAGE_850=y
 CONFIG_NLS_CODEPAGE_852=y
@@ -81,6 +78,9 @@ CONFIG_NLS_ISO8859_1=y
 CONFIG_NLS_ISO8859_2=y
 CONFIG_NLS_ISO8859_15=y
 CONFIG_NLS_UTF8=y
-CONFIG_MAGIC_SYSRQ=y
+CONFIG_FONTS=y
+CONFIG_FONT_8x8=y
+CONFIG_FONT_8x16=y
 CONFIG_DEBUG_KERNEL=y
+CONFIG_MAGIC_SYSRQ=y
 CONFIG_DEBUG_USER=y
diff --git a/arch/arm/configs/nhk8815_defconfig b/arch/arm/configs/nhk8815_defconfig
index 23595fc5a29a..d5881de42018 100644
--- a/arch/arm/configs/nhk8815_defconfig
+++ b/arch/arm/configs/nhk8815_defconfig
@@ -1,5 +1,4 @@
 # CONFIG_LOCALVERSION_AUTO is not set
-# CONFIG_SWAP is not set
 CONFIG_SYSVIPC=y
 CONFIG_NO_HZ_IDLE=y
 CONFIG_HIGH_RES_TIMERS=y
@@ -10,14 +9,14 @@ CONFIG_LOG_BUF_SHIFT=14
 CONFIG_BLK_DEV_INITRD=y
 CONFIG_EXPERT=y
 CONFIG_KALLSYMS_ALL=y
-CONFIG_SLAB=y
 # CONFIG_ARCH_MULTI_V7 is not set
 CONFIG_ARCH_NOMADIK=y
 CONFIG_MACH_NOMADIK_8815NHK=y
 CONFIG_AEABI=y
 CONFIG_MODULES=y
 CONFIG_MODULE_UNLOAD=y
-# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_SWAP is not set
+CONFIG_SLAB=y
 CONFIG_CMA=y
 CONFIG_NET=y
 CONFIG_PACKET=y
@@ -59,6 +58,7 @@ CONFIG_BLK_DEV_RAM=y
 CONFIG_SCSI=y
 CONFIG_BLK_DEV_SD=y
 CONFIG_CHR_DEV_SG=y
+# CONFIG_BLK_DEV_BSG is not set
 CONFIG_SCSI_CONSTANTS=y
 CONFIG_SCSI_LOGGING=y
 CONFIG_SCSI_SCAN_ASYNC=y
@@ -127,7 +127,6 @@ CONFIG_NFS_FS=y
 CONFIG_NFS_V3_ACL=y
 CONFIG_ROOT_NFS=y
 CONFIG_CIFS=m
-CONFIG_CIFS_WEAK_PW_HASH=y
 CONFIG_NLS_CODEPAGE_437=y
 CONFIG_NLS_ASCII=y
 CONFIG_NLS_ISO8859_1=y
@@ -136,7 +135,7 @@ CONFIG_CRYPTO_MD5=y
 CONFIG_CRYPTO_SHA1=y
 CONFIG_CRYPTO_DES=y
 # CONFIG_DEBUG_BUGVERBOSE is not set
-CONFIG_DEBUG_INFO=y
+CONFIG_DEBUG_INFO_DWARF_TOOLCHAIN_DEFAULT=y
 CONFIG_DEBUG_FS=y
 # CONFIG_SCHED_DEBUG is not set
 # CONFIG_DEBUG_PREEMPT is not set
diff --git a/arch/arm/configs/omap1_defconfig b/arch/arm/configs/omap1_defconfig
index 3148567b66b6..70511fe4b3ec 100644
--- a/arch/arm/configs/omap1_defconfig
+++ b/arch/arm/configs/omap1_defconfig
@@ -1,61 +1,49 @@
-# CONFIG_SWAP is not set
 CONFIG_SYSVIPC=y
 CONFIG_POSIX_MQUEUE=y
+CONFIG_NO_HZ_IDLE=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_PREEMPT=y
 CONFIG_BSD_PROCESS_ACCT=y
 CONFIG_IKCONFIG=y
 CONFIG_LOG_BUF_SHIFT=14
 CONFIG_BLK_DEV_INITRD=y
 CONFIG_EXPERT=y
-# CONFIG_KALLSYMS is not set
 # CONFIG_ELF_CORE is not set
 # CONFIG_BASE_FULL is not set
 # CONFIG_SHMEM is not set
-# CONFIG_VM_EVENT_COUNTERS is not set
-CONFIG_SLOB=y
+# CONFIG_KALLSYMS is not set
 CONFIG_PROFILING=y
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
-CONFIG_MODULE_FORCE_UNLOAD=y
-# CONFIG_BLK_DEV_BSG is not set
+CONFIG_ARCH_MULTI_V4T=y
+CONFIG_ARCH_MULTI_V5=y
+# CONFIG_ARCH_MULTI_V7 is not set
 CONFIG_ARCH_OMAP=y
 CONFIG_ARCH_OMAP1=y
-CONFIG_OMAP_RESET_CLOCKS=y
-# CONFIG_OMAP_MUX is not set
 CONFIG_OMAP_32K_TIMER=y
 CONFIG_OMAP_DM_TIMER=y
 CONFIG_ARCH_OMAP730=y
 CONFIG_ARCH_OMAP850=y
 CONFIG_ARCH_OMAP16XX=y
-CONFIG_MACH_OMAP_INNOVATOR=y
-CONFIG_MACH_OMAP_H2=y
-CONFIG_MACH_OMAP_H3=y
-CONFIG_MACH_HERALD=y
+# CONFIG_OMAP_MUX is not set
+CONFIG_OMAP_RESET_CLOCKS=y
 CONFIG_MACH_OMAP_OSK=y
-CONFIG_MACH_OMAP_PERSEUS2=y
-CONFIG_MACH_OMAP_FSAMPLE=y
-CONFIG_MACH_VOICEBLUE=y
 CONFIG_MACH_OMAP_PALMTE=y
-CONFIG_MACH_OMAP_PALMZ71=y
-CONFIG_MACH_OMAP_PALMTT=y
 CONFIG_MACH_SX1=y
 CONFIG_MACH_NOKIA770=y
 CONFIG_MACH_AMS_DELTA=y
 CONFIG_MACH_OMAP_GENERIC=y
-# CONFIG_ARM_THUMB is not set
-CONFIG_PCCARD=y
-CONFIG_OMAP_CF=y
-CONFIG_NO_HZ=y
-CONFIG_HIGH_RES_TIMERS=y
-CONFIG_PREEMPT=y
 CONFIG_AEABI=y
-CONFIG_LEDS=y
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
 CONFIG_CMDLINE="root=1f03 rootfstype=jffs2"
 CONFIG_FPE_NWFPE=y
-CONFIG_BINFMT_MISC=y
-CONFIG_PM=y
 # CONFIG_SUSPEND is not set
+CONFIG_PM=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_MODULE_FORCE_UNLOAD=y
+CONFIG_PARTITION_ADVANCED=y
+CONFIG_BINFMT_MISC=y
+# CONFIG_SWAP is not set
+CONFIG_SLOB=y
+# CONFIG_VM_EVENT_COUNTERS is not set
 CONFIG_NET=y
 CONFIG_PACKET=y
 CONFIG_UNIX=y
@@ -76,6 +64,8 @@ CONFIG_BT_RFCOMM=y
 CONFIG_BT_RFCOMM_TTY=y
 CONFIG_BT_BNEP=y
 CONFIG_BT_HIDP=y
+CONFIG_PCCARD=y
+CONFIG_OMAP_CF=y
 # CONFIG_STANDALONE is not set
 # CONFIG_PREVENT_FIRMWARE_BUILD is not set
 CONFIG_CONNECTOR=y
@@ -96,12 +86,21 @@ CONFIG_BLK_DEV_SD=y
 CONFIG_CHR_DEV_ST=y
 CONFIG_BLK_DEV_SR=y
 CONFIG_CHR_DEV_SG=y
+# CONFIG_BLK_DEV_BSG is not set
 CONFIG_ATA=m
 CONFIG_PATA_PCMCIA=m
 CONFIG_NETDEVICES=y
 CONFIG_TUN=y
 CONFIG_PHYLIB=y
 CONFIG_SMC91X=y
+CONFIG_PPP=y
+CONFIG_PPP_BSDCOMP=y
+CONFIG_PPP_DEFLATE=y
+CONFIG_PPP_FILTER=y
+CONFIG_PPP_MULTILINK=y
+CONFIG_PPP_ASYNC=y
+CONFIG_SLIP=y
+CONFIG_SLIP_COMPRESSED=y
 CONFIG_USB_CATC=y
 CONFIG_USB_KAWETH=y
 CONFIG_USB_PEGASUS=y
@@ -109,14 +108,6 @@ CONFIG_USB_RTL8150=y
 CONFIG_USB_USBNET=y
 # CONFIG_USB_NET_AX8817X is not set
 # CONFIG_USB_NET_CDC_SUBSET is not set
-CONFIG_PPP=y
-CONFIG_PPP_MULTILINK=y
-CONFIG_PPP_FILTER=y
-CONFIG_PPP_ASYNC=y
-CONFIG_PPP_DEFLATE=y
-CONFIG_PPP_BSDCOMP=y
-CONFIG_SLIP=y
-CONFIG_SLIP_COMPRESSED=y
 # CONFIG_INPUT_MOUSEDEV is not set
 CONFIG_INPUT_EVDEV=y
 CONFIG_INPUT_EVBUG=y
@@ -127,11 +118,11 @@ CONFIG_TOUCHSCREEN_ADS7846=y
 CONFIG_INPUT_MISC=y
 CONFIG_INPUT_UINPUT=y
 # CONFIG_SERIO is not set
+# CONFIG_LEGACY_PTYS is not set
 CONFIG_SERIAL_8250=y
 CONFIG_SERIAL_8250_CONSOLE=y
 CONFIG_SERIAL_8250_NR_UARTS=3
 CONFIG_SERIAL_8250_RUNTIME_UARTS=3
-# CONFIG_LEGACY_PTYS is not set
 CONFIG_HW_RANDOM=y
 CONFIG_I2C=y
 CONFIG_I2C_CHARDEV=y
@@ -153,11 +144,6 @@ CONFIG_FB_OMAP_LCD_MIPID=y
 CONFIG_LCD_CLASS_DEVICE=y
 CONFIG_FRAMEBUFFER_CONSOLE=y
 CONFIG_FRAMEBUFFER_CONSOLE_ROTATION=y
-CONFIG_FONTS=y
-CONFIG_FONT_8x8=y
-CONFIG_FONT_8x16=y
-CONFIG_FONT_6x11=y
-CONFIG_FONT_MINI_4x6=y
 CONFIG_LOGO=y
 # CONFIG_LOGO_LINUX_MONO is not set
 # CONFIG_LOGO_LINUX_VGA16 is not set
@@ -219,7 +205,6 @@ CONFIG_NFS_FS=y
 CONFIG_NFS_V3=y
 CONFIG_NFS_V4=y
 CONFIG_ROOT_NFS=y
-CONFIG_PARTITION_ADVANCED=y
 CONFIG_NLS_CODEPAGE_437=y
 CONFIG_NLS_CODEPAGE_850=y
 CONFIG_NLS_CODEPAGE_852=y
@@ -232,13 +217,7 @@ CONFIG_NLS_ISO8859_15=y
 CONFIG_NLS_KOI8_R=y
 CONFIG_NLS_UTF8=y
 # CONFIG_ENABLE_MUST_CHECK is not set
-CONFIG_MAGIC_SYSRQ=y
 CONFIG_DEBUG_KERNEL=y
-CONFIG_DEBUG_SPINLOCK=y
-CONFIG_DEBUG_MUTEXES=y
-# CONFIG_DEBUG_BUGVERBOSE is not set
-CONFIG_DEBUG_INFO=y
-CONFIG_DEBUG_USER=y
 CONFIG_SECURITY=y
 CONFIG_CRYPTO_ECB=y
 CONFIG_CRYPTO_PCBC=y
@@ -246,3 +225,14 @@ CONFIG_CRYPTO_DEFLATE=y
 CONFIG_CRYPTO_LZO=y
 # CONFIG_CRYPTO_ANSI_CPRNG is not set
 CONFIG_LIBCRC32C=y
+CONFIG_FONTS=y
+CONFIG_FONT_8x8=y
+CONFIG_FONT_8x16=y
+CONFIG_FONT_6x11=y
+CONFIG_FONT_MINI_4x6=y
+# CONFIG_DEBUG_BUGVERBOSE is not set
+CONFIG_DEBUG_INFO_DWARF_TOOLCHAIN_DEFAULT=y
+CONFIG_MAGIC_SYSRQ=y
+CONFIG_DEBUG_SPINLOCK=y
+CONFIG_DEBUG_MUTEXES=y
+CONFIG_DEBUG_USER=y
diff --git a/arch/arm/configs/omap2plus_defconfig b/arch/arm/configs/omap2plus_defconfig
index d933b787d934..2a66850d3288 100644
--- a/arch/arm/configs/omap2plus_defconfig
+++ b/arch/arm/configs/omap2plus_defconfig
@@ -2,7 +2,7 @@ CONFIG_KERNEL_LZMA=y
 CONFIG_SYSVIPC=y
 CONFIG_POSIX_MQUEUE=y
 CONFIG_AUDIT=y
-CONFIG_NO_HZ=y
+CONFIG_NO_HZ_IDLE=y
 CONFIG_HIGH_RES_TIMERS=y
 CONFIG_BSD_PROCESS_ACCT=y
 CONFIG_IKCONFIG=y
@@ -22,11 +22,8 @@ CONFIG_CGROUP_PERF=y
 CONFIG_NAMESPACES=y
 CONFIG_BLK_DEV_INITRD=y
 CONFIG_EXPERT=y
-CONFIG_SLAB=y
 CONFIG_PROFILING=y
 CONFIG_ARCH_MULTI_V6=y
-CONFIG_POWER_AVS_OMAP=y
-CONFIG_POWER_AVS_OMAP_CLASS3=y
 CONFIG_OMAP_RESET_CLOCKS=y
 CONFIG_ARCH_OMAP2=y
 CONFIG_ARCH_OMAP3=y
@@ -35,6 +32,8 @@ CONFIG_SOC_OMAP5=y
 CONFIG_SOC_AM33XX=y
 CONFIG_SOC_AM43XX=y
 CONFIG_SOC_DRA7XX=y
+CONFIG_POWER_AVS_OMAP=y
+CONFIG_POWER_AVS_OMAP_CLASS3=y
 CONFIG_ARM_THUMBEE=y
 CONFIG_ARM_ERRATA_411920=y
 CONFIG_SMP=y
@@ -54,7 +53,6 @@ CONFIG_CPU_IDLE=y
 CONFIG_ARM_CPUIDLE=y
 CONFIG_KERNEL_MODE_NEON=y
 CONFIG_PM_DEBUG=y
-CONFIG_ARM_CRYPTO=y
 CONFIG_CRYPTO_SHA1_ARM_NEON=m
 CONFIG_CRYPTO_SHA256_ARM=m
 CONFIG_CRYPTO_SHA512_ARM=m
@@ -69,9 +67,9 @@ CONFIG_MODULE_UNLOAD=y
 CONFIG_MODULE_FORCE_UNLOAD=y
 CONFIG_MODVERSIONS=y
 CONFIG_MODULE_SRCVERSION_ALL=y
-# CONFIG_BLK_DEV_BSG is not set
 CONFIG_PARTITION_ADVANCED=y
 CONFIG_BINFMT_MISC=y
+CONFIG_SLAB=y
 CONFIG_CMA=y
 CONFIG_ZSMALLOC=m
 CONFIG_NET=y
@@ -250,8 +248,6 @@ CONFIG_NET_ACT_POLICE=m
 CONFIG_NET_ACT_GACT=m
 CONFIG_NET_SWITCHDEV=y
 CONFIG_CAN=m
-CONFIG_CAN_C_CAN=m
-CONFIG_CAN_C_CAN_PLATFORM=m
 CONFIG_BT=m
 CONFIG_BT_RFCOMM=m
 CONFIG_BT_RFCOMM_TTY=y
@@ -316,6 +312,7 @@ CONFIG_PCI_ENDPOINT_TEST=m
 CONFIG_EEPROM_AT24=m
 CONFIG_EEPROM_AT25=m
 CONFIG_BLK_DEV_SD=y
+# CONFIG_BLK_DEV_BSG is not set
 CONFIG_SCSI_SCAN_ASYNC=y
 CONFIG_ATA=y
 CONFIG_SATA_AHCI_PLATFORM=y
@@ -350,6 +347,8 @@ CONFIG_AT803X_PHY=y
 CONFIG_SMSC_PHY=y
 CONFIG_DP83848_PHY=y
 CONFIG_DP83867_PHY=y
+CONFIG_CAN_C_CAN=m
+CONFIG_CAN_C_CAN_PLATFORM=m
 CONFIG_PPP=m
 CONFIG_PPP_BSDCOMP=m
 CONFIG_PPP_DEFLATE=m
@@ -419,8 +418,6 @@ CONFIG_SERIAL_8250_DETECT_IRQ=y
 CONFIG_SERIAL_8250_RSA=y
 CONFIG_SERIAL_8250_OMAP=y
 CONFIG_SERIAL_OF_PLATFORM=y
-CONFIG_SERIAL_OMAP=y
-CONFIG_SERIAL_OMAP_CONSOLE=y
 CONFIG_SERIAL_DEV_BUS=y
 CONFIG_I2C_CHARDEV=y
 CONFIG_SPI=y
@@ -430,7 +427,6 @@ CONFIG_SPI_TI_QSPI=m
 CONFIG_HSI=m
 CONFIG_OMAP_SSI=m
 CONFIG_SSI_PROTOCOL=m
-CONFIG_PTP_1588_CLOCK=y
 CONFIG_PINCTRL_SINGLE=y
 CONFIG_DEBUG_GPIO=y
 CONFIG_GPIO_SYSFS=y
@@ -494,15 +490,15 @@ CONFIG_REGULATOR_TWL4030=y
 CONFIG_RC_CORE=m
 CONFIG_LIRC=y
 CONFIG_RC_DEVICES=y
-CONFIG_IR_SPI=m
-CONFIG_IR_RX51=m
 CONFIG_IR_GPIO_TX=m
 CONFIG_IR_PWM_TX=m
+CONFIG_IR_RX51=m
+CONFIG_IR_SPI=m
 CONFIG_MEDIA_SUPPORT=m
 CONFIG_V4L_PLATFORM_DRIVERS=y
 CONFIG_VIDEO_OMAP3=m
-CONFIG_VIDEO_TVP5150=m
 CONFIG_VIDEO_MT9P031=m
+CONFIG_VIDEO_TVP5150=m
 CONFIG_DRM=m
 CONFIG_DRM_OMAP=m
 CONFIG_OMAP5_DSS_HDMI=y
@@ -553,6 +549,8 @@ CONFIG_SND_SOC_OMAP_ABE_TWL6040=m
 CONFIG_SND_SOC_OMAP_HDMI=m
 CONFIG_SND_SOC_CPCAP=m
 CONFIG_SND_SOC_TLV320AIC23_I2C=m
+CONFIG_SND_SOC_TLV320AIC3X=m
+CONFIG_SND_SOC_TLV320AIC3X_I2C=m
 CONFIG_SND_SIMPLE_CARD=m
 CONFIG_SND_AUDIO_GRAPH_CARD=m
 CONFIG_HID_GENERIC=m
@@ -576,6 +574,7 @@ CONFIG_USB_INVENTRA_DMA=y
 CONFIG_USB_TI_CPPI41_DMA=y
 CONFIG_USB_TUSB_OMAP_DMA=y
 CONFIG_USB_DWC3=m
+CONFIG_USB_ISP1760=m
 CONFIG_USB_SERIAL=m
 CONFIG_USB_SERIAL_GENERIC=y
 CONFIG_USB_SERIAL_SIMPLE=m
@@ -723,9 +722,8 @@ CONFIG_FONT_8x8=y
 CONFIG_FONT_8x16=y
 CONFIG_PRINTK_TIME=y
 # CONFIG_DEBUG_BUGVERBOSE is not set
-CONFIG_DEBUG_INFO=y
-CONFIG_DEBUG_INFO_SPLIT=y
 CONFIG_DEBUG_INFO_DWARF4=y
+CONFIG_DEBUG_INFO_SPLIT=y
 CONFIG_MAGIC_SYSRQ=y
 CONFIG_DEBUG_FS=y
 CONFIG_SCHEDSTATS=y
diff --git a/arch/arm/configs/orion5x_defconfig b/arch/arm/configs/orion5x_defconfig
index b9e3b647e732..0629b088a584 100644
--- a/arch/arm/configs/orion5x_defconfig
+++ b/arch/arm/configs/orion5x_defconfig
@@ -1,23 +1,14 @@
 CONFIG_SYSVIPC=y
-CONFIG_NO_HZ=y
+CONFIG_NO_HZ_IDLE=y
 CONFIG_HIGH_RES_TIMERS=y
+CONFIG_PREEMPT=y
 CONFIG_LOG_BUF_SHIFT=14
 CONFIG_EXPERT=y
-# CONFIG_SLUB_DEBUG is not set
 CONFIG_PROFILING=y
-CONFIG_KPROBES=y
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
-# CONFIG_BLK_DEV_BSG is not set
-CONFIG_PARTITION_ADVANCED=y
-CONFIG_BSD_DISKLABEL=y
 CONFIG_ARCH_MULTI_V5=y
 # CONFIG_ARCH_MULTI_V6 is not set
 # CONFIG_ARCH_MULTI_V7 is not set
 CONFIG_ARCH_ORION5X=y
-CONFIG_ARCH_ORION5X_DT=y
-CONFIG_MACH_DB88F5281=y
-CONFIG_MACH_RD88F5182=y
 CONFIG_MACH_RD88F5182_DT=y
 CONFIG_MACH_KUROBOX_PRO=y
 CONFIG_MACH_DNS323=y
@@ -25,28 +16,20 @@ CONFIG_MACH_TS209=y
 CONFIG_MACH_TERASTATION_PRO2=y
 CONFIG_MACH_LINKSTATION_PRO=y
 CONFIG_MACH_LINKSTATION_MINI=y
-CONFIG_MACH_LINKSTATION_LS_HGL=y
 CONFIG_MACH_TS409=y
-CONFIG_MACH_WRT350N_V2=y
 CONFIG_MACH_TS78XX=y
 CONFIG_MACH_MV2120=y
-CONFIG_MACH_EDMINI_V2_DT=y
-CONFIG_MACH_D2NET=y
-CONFIG_MACH_BIGDISK=y
 CONFIG_MACH_NET2BIG=y
-CONFIG_MACH_MSS2=y
-CONFIG_MACH_WNR854T=y
-CONFIG_MACH_RD88F5181L_GE=y
-CONFIG_MACH_RD88F5181L_FXO=y
-CONFIG_MACH_RD88F6183AP_GE=y
-CONFIG_PREEMPT=y
 CONFIG_AEABI=y
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
 CONFIG_ARM_APPENDED_DTB=y
 CONFIG_ARM_ATAG_DTB_COMPAT=y
 CONFIG_FPE_NWFPE=y
 CONFIG_VFP=y
+CONFIG_KPROBES=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_PARTITION_ADVANCED=y
+CONFIG_BSD_DISKLABEL=y
 CONFIG_NET=y
 CONFIG_PACKET=y
 CONFIG_UNIX=y
@@ -58,6 +41,7 @@ CONFIG_IP_PNP_BOOTP=y
 # CONFIG_IPV6 is not set
 CONFIG_NET_DSA=y
 CONFIG_NET_PKTGEN=m
+# CONFIG_VGA_ARB is not set
 CONFIG_MTD=y
 CONFIG_MTD_CMDLINE_PARTS=y
 CONFIG_MTD_BLOCK=y
@@ -69,13 +53,14 @@ CONFIG_MTD_CFI_INTELEXT=y
 CONFIG_MTD_CFI_AMDSTD=y
 CONFIG_MTD_PHYSMAP=y
 CONFIG_MTD_RAW_NAND=y
-CONFIG_MTD_NAND_PLATFORM=y
 CONFIG_MTD_NAND_ORION=y
+CONFIG_MTD_NAND_PLATFORM=y
 CONFIG_BLK_DEV_LOOP=y
 # CONFIG_SCSI_PROC_FS is not set
 CONFIG_BLK_DEV_SD=y
 CONFIG_BLK_DEV_SR=m
 CONFIG_CHR_DEV_SG=m
+# CONFIG_BLK_DEV_BSG is not set
 CONFIG_ATA=y
 CONFIG_SATA_MV=y
 CONFIG_NETDEVICES=y
@@ -103,7 +88,6 @@ CONFIG_I2C_CHARDEV=y
 CONFIG_I2C_MV64XXX=y
 CONFIG_GPIO_SYSFS=y
 CONFIG_SENSORS_LM75=y
-# CONFIG_VGA_ARB is not set
 CONFIG_USB=y
 CONFIG_USB_EHCI_HCD=y
 CONFIG_USB_EHCI_ROOT_HUB_TT=y
@@ -148,17 +132,18 @@ CONFIG_NLS_CODEPAGE_437=y
 CONFIG_NLS_CODEPAGE_850=y
 CONFIG_NLS_ISO8859_1=y
 CONFIG_NLS_ISO8859_2=y
+CONFIG_CRYPTO_CBC=m
+CONFIG_CRYPTO_ECB=m
+CONFIG_CRYPTO_PCBC=m
+CONFIG_CRYPTO_DEV_MARVELL_CESA=y
+CONFIG_CRC_T10DIF=y
+# CONFIG_DEBUG_BUGVERBOSE is not set
+CONFIG_DEBUG_INFO_DWARF_TOOLCHAIN_DEFAULT=y
 CONFIG_MAGIC_SYSRQ=y
 CONFIG_DEBUG_FS=y
-# CONFIG_DEBUG_BUGVERBOSE is not set
-CONFIG_DEBUG_INFO=y
+# CONFIG_SLUB_DEBUG is not set
 CONFIG_LATENCYTOP=y
 # CONFIG_FTRACE is not set
 CONFIG_DEBUG_USER=y
 CONFIG_DEBUG_LL=y
-CONFIG_CRYPTO_CBC=m
-CONFIG_CRYPTO_ECB=m
-CONFIG_CRYPTO_PCBC=m
 # CONFIG_CRYPTO_ANSI_CPRNG is not set
-CONFIG_CRYPTO_DEV_MARVELL_CESA=y
-CONFIG_CRC_T10DIF=y
diff --git a/arch/arm/configs/oxnas_v6_defconfig b/arch/arm/configs/oxnas_v6_defconfig
index de37f7e90999..70a67b3fc91b 100644
--- a/arch/arm/configs/oxnas_v6_defconfig
+++ b/arch/arm/configs/oxnas_v6_defconfig
@@ -1,5 +1,5 @@
 CONFIG_SYSVIPC=y
-CONFIG_NO_HZ=y
+CONFIG_NO_HZ_IDLE=y
 CONFIG_HIGH_RES_TIMERS=y
 CONFIG_CGROUPS=y
 CONFIG_BLK_DEV_INITRD=y
@@ -7,17 +7,12 @@ CONFIG_EMBEDDED=y
 CONFIG_PERF_EVENTS=y
 CONFIG_STRICT_KERNEL_RWX=y
 CONFIG_STRICT_MODULE_RWX=y
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
-CONFIG_PARTITION_ADVANCED=y
-CONFIG_CMDLINE_PARTITION=y
 CONFIG_ARCH_MULTI_V6=y
 CONFIG_ARCH_OXNAS=y
 CONFIG_MACH_OX820=y
 CONFIG_SMP=y
 CONFIG_NR_CPUS=16
-CONFIG_CMA=y
-CONFIG_FORCE_MAX_ZONEORDER=12
+CONFIG_ARCH_FORCE_MAX_ORDER=12
 CONFIG_SECCOMP=y
 CONFIG_ARM_APPENDED_DTB=y
 CONFIG_ARM_ATAG_DTB_COMPAT=y
@@ -26,6 +21,11 @@ CONFIG_EFI=y
 CONFIG_CPU_IDLE=y
 CONFIG_ARM_CPUIDLE=y
 CONFIG_VFP=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_PARTITION_ADVANCED=y
+CONFIG_CMDLINE_PARTITION=y
+CONFIG_CMA=y
 CONFIG_NET=y
 CONFIG_PACKET=y
 CONFIG_UNIX=y
@@ -44,8 +44,6 @@ CONFIG_IPV6_TUNNEL=m
 CONFIG_IPV6_MULTIPLE_TABLES=y
 CONFIG_DEVTMPFS=y
 CONFIG_DEVTMPFS_MOUNT=y
-CONFIG_DMA_CMA=y
-CONFIG_CMA_SIZE_MBYTES=64
 CONFIG_MTD=y
 CONFIG_MTD_CMDLINE_PARTS=y
 CONFIG_MTD_BLOCK=y
@@ -88,5 +86,7 @@ CONFIG_PSTORE_RAM=y
 CONFIG_NLS_CODEPAGE_437=y
 CONFIG_NLS_ISO8859_1=y
 CONFIG_NLS_UTF8=y
+CONFIG_DMA_CMA=y
+CONFIG_CMA_SIZE_MBYTES=64
 CONFIG_PRINTK_TIME=y
 CONFIG_MAGIC_SYSRQ=y
diff --git a/arch/arm/configs/palmz72_defconfig b/arch/arm/configs/palmz72_defconfig
index b47c8abe85bc..a9a808bc2f70 100644
--- a/arch/arm/configs/palmz72_defconfig
+++ b/arch/arm/configs/palmz72_defconfig
@@ -1,23 +1,23 @@
 # CONFIG_LOCALVERSION_AUTO is not set
 CONFIG_SYSVIPC=y
+CONFIG_PREEMPT=y
 CONFIG_LOG_BUF_SHIFT=14
 CONFIG_SYSFS_DEPRECATED_V2=y
 CONFIG_BLK_DEV_INITRD=y
-CONFIG_SLAB=y
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
 # CONFIG_BLK_DEV_BSG is not set
+# CONFIG_ARCH_MULTI_V7 is not set
 CONFIG_ARCH_PXA=y
 CONFIG_ARCH_PXA_PALM=y
 # CONFIG_MACH_PALMTX is not set
-CONFIG_PREEMPT=y
 CONFIG_AEABI=y
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_UNUSED_BOARD_FILES=y
 CONFIG_CMDLINE="mem=32M console=tty root=/dev/mmcblk0"
 CONFIG_FPE_NWFPE=y
 CONFIG_PM=y
 CONFIG_APM_EMULATION=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_SLAB=y
 CONFIG_NET=y
 CONFIG_PACKET=y
 CONFIG_UNIX=y
@@ -51,8 +51,6 @@ CONFIG_BACKLIGHT_CLASS_DEVICE=y
 CONFIG_BACKLIGHT_PWM=y
 # CONFIG_VGA_CONSOLE is not set
 CONFIG_FRAMEBUFFER_CONSOLE=y
-CONFIG_FONTS=y
-CONFIG_FONT_8x8=y
 # CONFIG_USB_SUPPORT is not set
 CONFIG_MMC=y
 CONFIG_MMC_DEBUG=y
@@ -71,5 +69,7 @@ CONFIG_TMPFS=y
 CONFIG_NLS_DEFAULT="utf8"
 CONFIG_NLS_CODEPAGE_866=y
 CONFIG_NLS_UTF8=y
-CONFIG_DEBUG_USER=y
 CONFIG_CRC_T10DIF=y
+CONFIG_FONTS=y
+CONFIG_FONT_8x8=y
+CONFIG_DEBUG_USER=y
diff --git a/arch/arm/configs/pcm027_defconfig b/arch/arm/configs/pcm027_defconfig
index e97a158081fc..a392312a13ce 100644
--- a/arch/arm/configs/pcm027_defconfig
+++ b/arch/arm/configs/pcm027_defconfig
@@ -1,6 +1,8 @@
-# CONFIG_SWAP is not set
 CONFIG_SYSVIPC=y
 CONFIG_POSIX_MQUEUE=y
+CONFIG_NO_HZ_IDLE=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_PREEMPT=y
 CONFIG_BSD_PROCESS_ACCT=y
 CONFIG_IKCONFIG=y
 CONFIG_IKCONFIG_PROC=y
@@ -8,21 +10,19 @@ CONFIG_LOG_BUF_SHIFT=14
 # CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
 CONFIG_EXPERT=y
 # CONFIG_KALLSYMS is not set
-CONFIG_SLAB=y
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
-CONFIG_MODULE_FORCE_UNLOAD=y
-# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_ARCH_MULTI_V7 is not set
 CONFIG_ARCH_PXA=y
 CONFIG_MACH_PCM027=y
 CONFIG_MACH_PCM990_BASEBOARD=y
-CONFIG_NO_HZ=y
-CONFIG_HIGH_RES_TIMERS=y
-CONFIG_PREEMPT=y
 CONFIG_AEABI=y
 # CONFIG_OABI_COMPAT is not set
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_UNUSED_BOARD_FILES=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_MODULE_FORCE_UNLOAD=y
+CONFIG_PARTITION_ADVANCED=y
+# CONFIG_SWAP is not set
+CONFIG_SLAB=y
 CONFIG_NET=y
 CONFIG_PACKET=y
 CONFIG_UNIX=y
@@ -42,6 +42,7 @@ CONFIG_MTD_PHYSMAP=y
 # CONFIG_BLK_DEV is not set
 CONFIG_SCSI=y
 CONFIG_BLK_DEV_SD=y
+# CONFIG_BLK_DEV_BSG is not set
 # CONFIG_SCSI_LOWLEVEL is not set
 CONFIG_NETDEVICES=y
 CONFIG_NET_ETHERNET=y
@@ -50,9 +51,9 @@ CONFIG_SMC91X=y
 # CONFIG_INPUT_KEYBOARD is not set
 # CONFIG_INPUT_MOUSE is not set
 # CONFIG_SERIO is not set
+# CONFIG_LEGACY_PTYS is not set
 CONFIG_SERIAL_PXA=y
 CONFIG_SERIAL_PXA_CONSOLE=y
-# CONFIG_LEGACY_PTYS is not set
 # CONFIG_HW_RANDOM is not set
 CONFIG_I2C=y
 CONFIG_I2C_CHARDEV=y
@@ -83,7 +84,6 @@ CONFIG_JFFS2_FS=y
 CONFIG_NFS_FS=y
 CONFIG_NFS_V3=y
 CONFIG_ROOT_NFS=y
-CONFIG_PARTITION_ADVANCED=y
 CONFIG_NLS_DEFAULT="iso8859-15"
 CONFIG_NLS_CODEPAGE_850=y
 CONFIG_NLS_ISO8859_15=y
diff --git a/arch/arm/configs/pleb_defconfig b/arch/arm/configs/pleb_defconfig
index 2170148b975c..fd2667873273 100644
--- a/arch/arm/configs/pleb_defconfig
+++ b/arch/arm/configs/pleb_defconfig
@@ -1,19 +1,20 @@
-# CONFIG_SWAP is not set
 CONFIG_SYSVIPC=y
 CONFIG_LOG_BUF_SHIFT=14
 CONFIG_BLK_DEV_INITRD=y
 CONFIG_EXPERT=y
 # CONFIG_HOTPLUG is not set
 # CONFIG_SHMEM is not set
-CONFIG_MODULES=y
+CONFIG_ARCH_MULTI_V4=y
+# CONFIG_ARCH_MULTI_V7 is not set
 CONFIG_ARCH_SA1100=y
 CONFIG_SA1100_PLEB=y
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_UNUSED_BOARD_FILES=y
 CONFIG_CMDLINE="console=ttySA0,9600 mem=16M@0xc0000000 mem=16M@0xc8000000 root=/dev/ram initrd=0xc0400000,4M"
 CONFIG_CPU_FREQ_DEFAULT_GOV_PERFORMANCE=y
 CONFIG_CPU_FREQ_GOV_ONDEMAND=y
 CONFIG_FPE_NWFPE=y
+CONFIG_MODULES=y
+# CONFIG_SWAP is not set
 CONFIG_NET=y
 CONFIG_PACKET=y
 CONFIG_UNIX=y
@@ -21,9 +22,9 @@ CONFIG_INET=y
 CONFIG_SYN_COOKIES=y
 # CONFIG_IPV6 is not set
 CONFIG_MTD=y
+CONFIG_MTD_CMDLINE_PARTS=y
 CONFIG_MTD_REDBOOT_PARTS=y
 CONFIG_MTD_REDBOOT_PARTS_UNALLOCATED=y
-CONFIG_MTD_CMDLINE_PARTS=y
 CONFIG_MTD_BLOCK=y
 CONFIG_MTD_CFI=y
 CONFIG_MTD_CFI_INTELEXT=y
diff --git a/arch/arm/configs/pxa168_defconfig b/arch/arm/configs/pxa168_defconfig
index 0947f022954d..826ebbef2e3c 100644
--- a/arch/arm/configs/pxa168_defconfig
+++ b/arch/arm/configs/pxa168_defconfig
@@ -1,23 +1,21 @@
 CONFIG_SYSVIPC=y
-CONFIG_LOG_BUF_SHIFT=14
 CONFIG_SYSFS_DEPRECATED_V2=y
-CONFIG_SLAB=y
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
-CONFIG_MODULE_FORCE_UNLOAD=y
 # CONFIG_BLK_DEV_BSG is not set
-CONFIG_ARCH_MMP=y
 CONFIG_MACH_ASPENITE=y
 CONFIG_MACH_ZYLONITE2=y
 CONFIG_MACH_AVENGERS_LITE=y
-CONFIG_NO_HZ=y
+CONFIG_NO_HZ_IDLE=y
 CONFIG_HIGH_RES_TIMERS=y
 CONFIG_PREEMPT=y
 CONFIG_AEABI=y
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_LOG_BUF_SHIFT=14
+CONFIG_ARCH_MMP=y
 CONFIG_CMDLINE="root=/dev/nfs rootfstype=nfs nfsroot=192.168.2.100:/nfsroot/ ip=192.168.2.101:192.168.2.100::255.255.255.0::eth0:on console=ttyS0,115200 mem=128M"
 CONFIG_FPE_NWFPE=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_MODULE_FORCE_UNLOAD=y
+CONFIG_SLAB=y
 CONFIG_NET=y
 CONFIG_PACKET=y
 CONFIG_UNIX=y
@@ -34,9 +32,9 @@ CONFIG_SMC91X=y
 # CONFIG_INPUT_KEYBOARD is not set
 # CONFIG_INPUT_MOUSE is not set
 # CONFIG_SERIO is not set
+# CONFIG_LEGACY_PTYS is not set
 CONFIG_SERIAL_PXA=y
 CONFIG_SERIAL_PXA_CONSOLE=y
-# CONFIG_LEGACY_PTYS is not set
 # CONFIG_HW_RANDOM is not set
 # CONFIG_HWMON is not set
 # CONFIG_VGA_CONSOLE is not set
@@ -49,12 +47,12 @@ CONFIG_NFS_V3=y
 CONFIG_NFS_V3_ACL=y
 CONFIG_NFS_V4=y
 CONFIG_ROOT_NFS=y
+CONFIG_CRC_CCITT=y
 CONFIG_PRINTK_TIME=y
-CONFIG_MAGIC_SYSRQ=y
 CONFIG_DEBUG_KERNEL=y
+CONFIG_DEBUG_INFO_DWARF_TOOLCHAIN_DEFAULT=y
+CONFIG_MAGIC_SYSRQ=y
 # CONFIG_DEBUG_PREEMPT is not set
-CONFIG_DEBUG_INFO=y
 CONFIG_DEBUG_USER=y
 CONFIG_DEBUG_LL=y
 # CONFIG_CRYPTO_ANSI_CPRNG is not set
-CONFIG_CRC_CCITT=y
diff --git a/arch/arm/configs/pxa255-idp_defconfig b/arch/arm/configs/pxa255-idp_defconfig
index 4a383afa5e87..ae0444949a87 100644
--- a/arch/arm/configs/pxa255-idp_defconfig
+++ b/arch/arm/configs/pxa255-idp_defconfig
@@ -1,15 +1,12 @@
 CONFIG_SYSVIPC=y
 CONFIG_LOG_BUF_SHIFT=14
-CONFIG_MODULES=y
+# CONFIG_ARCH_MULTI_V7 is not set
 CONFIG_ARCH_PXA=y
 CONFIG_ARCH_PXA_IDP=y
-# CONFIG_ARM_THUMB is not set
-CONFIG_LEDS=y
-CONFIG_LEDS_CPU=y
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_UNUSED_BOARD_FILES=y
 CONFIG_CMDLINE="root=/dev/nfs ip=dhcp console=ttyS0,115200 mem=64M"
 CONFIG_FPE_NWFPE=y
+CONFIG_MODULES=y
 CONFIG_NET=y
 CONFIG_UNIX=y
 CONFIG_INET=y
@@ -37,18 +34,22 @@ CONFIG_FB=y
 CONFIG_FB_PXA=y
 # CONFIG_VGA_CONSOLE is not set
 CONFIG_FRAMEBUFFER_CONSOLE=y
-CONFIG_FONTS=y
-CONFIG_FONT_8x8=y
-CONFIG_FONT_8x16=y
 CONFIG_LOGO=y
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=y
+CONFIG_LEDS_TRIGGERS=y
+CONFIG_LEDS_TRIGGER_CPU=y
 CONFIG_EXT2_FS=y
 CONFIG_MSDOS_FS=y
 CONFIG_JFFS2_FS=y
 CONFIG_NFS_FS=y
 CONFIG_ROOT_NFS=y
 CONFIG_NLS_ISO8859_1=y
-CONFIG_MAGIC_SYSRQ=y
+CONFIG_FONTS=y
+CONFIG_FONT_8x8=y
+CONFIG_FONT_8x16=y
 CONFIG_DEBUG_KERNEL=y
-CONFIG_DEBUG_INFO=y
+CONFIG_DEBUG_INFO_DWARF_TOOLCHAIN_DEFAULT=y
+CONFIG_MAGIC_SYSRQ=y
 CONFIG_DEBUG_USER=y
 CONFIG_DEBUG_LL=y
diff --git a/arch/arm/configs/pxa3xx_defconfig b/arch/arm/configs/pxa3xx_defconfig
index f0c34017f2aa..d1e83b52e03a 100644
--- a/arch/arm/configs/pxa3xx_defconfig
+++ b/arch/arm/configs/pxa3xx_defconfig
@@ -1,21 +1,18 @@
 CONFIG_SYSVIPC=y
+CONFIG_PREEMPT=y
 CONFIG_LOG_BUF_SHIFT=18
 CONFIG_SYSFS_DEPRECATED_V2=y
 # CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
 CONFIG_KALLSYMS_ALL=y
-CONFIG_SLAB=y
-CONFIG_MODULES=y
 # CONFIG_BLK_DEV_BSG is not set
+# CONFIG_ARCH_MULTI_V7 is not set
 CONFIG_ARCH_PXA=y
-CONFIG_MACH_LITTLETON=y
-CONFIG_MACH_TAVOREVB=y
-CONFIG_MACH_SAAR=y
-CONFIG_PREEMPT=y
+CONFIG_MACH_PXA3XX_DT=y
 CONFIG_AEABI=y
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
 CONFIG_CMDLINE="root=/dev/nfs rootfstype=nfs nfsroot=192.168.1.100:/nfsroot/ ip=192.168.1.101:192.168.1.100::255.255.255.0::eth0:on console=ttyS0,115200 mem=64M debug"
 CONFIG_FPE_NWFPE=y
+CONFIG_MODULES=y
+CONFIG_SLAB=y
 CONFIG_NET=y
 CONFIG_PACKET=y
 CONFIG_UNIX=y
@@ -30,11 +27,11 @@ CONFIG_IP_PNP=y
 # CONFIG_PREVENT_FIRMWARE_BUILD is not set
 CONFIG_MTD=y
 CONFIG_MTD_BLOCK=y
-CONFIG_MTD_RAW_NAND=y
-CONFIG_MTD_NAND_MARVELL=y
 CONFIG_MTD_ONENAND=y
 CONFIG_MTD_ONENAND_VERIFY_WRITE=y
 CONFIG_MTD_ONENAND_GENERIC=y
+CONFIG_MTD_RAW_NAND=y
+CONFIG_MTD_NAND_MARVELL=y
 CONFIG_BLK_DEV_LOOP=y
 CONFIG_BLK_DEV_RAM=y
 CONFIG_NETDEVICES=y
@@ -44,12 +41,10 @@ CONFIG_SMC91X=y
 # CONFIG_KEYBOARD_ATKBD is not set
 CONFIG_KEYBOARD_GPIO=y
 CONFIG_KEYBOARD_PXA27x=y
-CONFIG_KEYBOARD_PXA930_ROTARY=y
-CONFIG_MOUSE_PXA930_TRKBALL=y
 CONFIG_INPUT_TOUCHSCREEN=y
+# CONFIG_LEGACY_PTYS is not set
 CONFIG_SERIAL_PXA=y
 CONFIG_SERIAL_PXA_CONSOLE=y
-# CONFIG_LEGACY_PTYS is not set
 # CONFIG_HW_RANDOM is not set
 CONFIG_I2C=y
 # CONFIG_I2C_HELPER_AUTO is not set
@@ -60,7 +55,6 @@ CONFIG_GPIO_MAX732X=y
 CONFIG_GPIO_PCA953X=y
 CONFIG_GPIO_PCF857X=y
 CONFIG_GPIO_MAX7301=y
-CONFIG_POWER_SUPPLY=y
 CONFIG_POWER_SUPPLY_DEBUG=y
 CONFIG_PDA_POWER=y
 CONFIG_BATTERY_DA9030=y
@@ -78,8 +72,6 @@ CONFIG_BACKLIGHT_DA903X=y
 # CONFIG_VGA_CONSOLE is not set
 CONFIG_FRAMEBUFFER_CONSOLE=y
 CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY=y
-CONFIG_FONTS=y
-CONFIG_FONT_6x11=y
 CONFIG_LOGO=y
 # CONFIG_USB_SUPPORT is not set
 CONFIG_MMC=y
@@ -105,9 +97,11 @@ CONFIG_NFS_V3_ACL=y
 CONFIG_NFS_V4=y
 CONFIG_ROOT_NFS=y
 CONFIG_NLS=y
+CONFIG_FONTS=y
+CONFIG_FONT_6x11=y
 CONFIG_PRINTK_TIME=y
-CONFIG_MAGIC_SYSRQ=y
 CONFIG_DEBUG_KERNEL=y
+CONFIG_MAGIC_SYSRQ=y
 CONFIG_DEBUG_SHIRQ=y
 CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC=y
 # CONFIG_SCHED_DEBUG is not set
diff --git a/arch/arm/configs/pxa910_defconfig b/arch/arm/configs/pxa910_defconfig
index b21196372158..353008de5678 100644
--- a/arch/arm/configs/pxa910_defconfig
+++ b/arch/arm/configs/pxa910_defconfig
@@ -1,23 +1,21 @@
 CONFIG_SYSVIPC=y
+CONFIG_NO_HZ_IDLE=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_PREEMPT=y
 CONFIG_LOG_BUF_SHIFT=14
 CONFIG_SYSFS_DEPRECATED_V2=y
 CONFIG_BLK_DEV_INITRD=y
-CONFIG_SLAB=y
+CONFIG_ARCH_MMP=y
+CONFIG_CMDLINE="root=/dev/nfs rootfstype=nfs nfsroot=192.168.2.100:/nfsroot/ ip=192.168.2.101:192.168.2.100::255.255.255.0::eth0:on console=ttyS0,115200 mem=128M earlyprintk"
 CONFIG_MODULES=y
 CONFIG_MODULE_UNLOAD=y
 CONFIG_MODULE_FORCE_UNLOAD=y
 # CONFIG_BLK_DEV_BSG is not set
-CONFIG_ARCH_MMP=y
 CONFIG_MACH_TAVOREVB=y
 CONFIG_MACH_TTC_DKB=y
-CONFIG_NO_HZ=y
-CONFIG_HIGH_RES_TIMERS=y
-CONFIG_PREEMPT=y
 CONFIG_AEABI=y
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
-CONFIG_CMDLINE="root=/dev/nfs rootfstype=nfs nfsroot=192.168.2.100:/nfsroot/ ip=192.168.2.101:192.168.2.100::255.255.255.0::eth0:on console=ttyS0,115200 mem=128M earlyprintk"
 CONFIG_FPE_NWFPE=y
+CONFIG_SLAB=y
 CONFIG_NET=y
 CONFIG_PACKET=y
 CONFIG_UNIX=y
@@ -34,9 +32,12 @@ CONFIG_SMC91X=y
 # CONFIG_INPUT_KEYBOARD is not set
 # CONFIG_INPUT_MOUSE is not set
 # CONFIG_SERIO is not set
+# CONFIG_LEGACY_PTYS is not set
 CONFIG_SERIAL_PXA=y
 CONFIG_SERIAL_PXA_CONSOLE=y
+# CONFIG_HW_RANDOM is not set
 CONFIG_SPI=y
+# CONFIG_HWMON is not set
 CONFIG_FB=y
 CONFIG_MMP_DISP=y
 CONFIG_MMP_DISP_CONTROLLER=y
@@ -44,9 +45,6 @@ CONFIG_MMP_SPI=y
 CONFIG_MMP_PANEL_TPOHVGA=y
 CONFIG_MMP_FB=y
 CONFIG_LOGO=y
-# CONFIG_LEGACY_PTYS is not set
-# CONFIG_HW_RANDOM is not set
-# CONFIG_HWMON is not set
 # CONFIG_VGA_CONSOLE is not set
 # CONFIG_USB_SUPPORT is not set
 CONFIG_TMPFS=y
@@ -57,14 +55,14 @@ CONFIG_NFS_V3=y
 CONFIG_NFS_V3_ACL=y
 CONFIG_NFS_V4=y
 CONFIG_ROOT_NFS=y
+CONFIG_CRC_CCITT=y
 CONFIG_PRINTK_TIME=y
-CONFIG_MAGIC_SYSRQ=y
 CONFIG_DEBUG_KERNEL=y
+CONFIG_DEBUG_INFO_DWARF_TOOLCHAIN_DEFAULT=y
+CONFIG_MAGIC_SYSRQ=y
 # CONFIG_DEBUG_PREEMPT is not set
-CONFIG_DEBUG_INFO=y
 CONFIG_DEBUG_USER=y
 CONFIG_DEBUG_LL=y
 CONFIG_DEBUG_MMP_UART2=y
 CONFIG_EARLY_PRINTK=y
 # CONFIG_CRYPTO_ANSI_CPRNG is not set
-CONFIG_CRC_CCITT=y
diff --git a/arch/arm/configs/pxa_defconfig b/arch/arm/configs/pxa_defconfig
index 58f4834289e6..d60cc9cc4c21 100644
--- a/arch/arm/configs/pxa_defconfig
+++ b/arch/arm/configs/pxa_defconfig
@@ -1,8 +1,9 @@
 CONFIG_SYSVIPC=y
 CONFIG_POSIX_MQUEUE=y
 CONFIG_FHANDLE=y
-CONFIG_NO_HZ=y
+CONFIG_NO_HZ_IDLE=y
 CONFIG_HIGH_RES_TIMERS=y
+CONFIG_PREEMPT=y
 CONFIG_BSD_PROCESS_ACCT=y
 CONFIG_BSD_PROCESS_ACCT_V3=y
 CONFIG_IKCONFIG=y
@@ -11,82 +12,16 @@ CONFIG_LOG_BUF_SHIFT=13
 CONFIG_BLK_DEV_INITRD=y
 CONFIG_KALLSYMS_ALL=y
 CONFIG_EMBEDDED=y
-CONFIG_SLOB=y
 CONFIG_PROFILING=y
-CONFIG_KPROBES=y
-CONFIG_MODULES=y
-CONFIG_MODULE_FORCE_LOAD=y
-CONFIG_MODULE_UNLOAD=y
-CONFIG_MODULE_FORCE_UNLOAD=y
-CONFIG_MODVERSIONS=y
-CONFIG_MODULE_SRCVERSION_ALL=y
-CONFIG_PARTITION_ADVANCED=y
-CONFIG_LDM_PARTITION=y
-CONFIG_CMDLINE_PARTITION=y
+# CONFIG_ARCH_MULTI_V7 is not set
 CONFIG_ARCH_PXA=y
-CONFIG_ARCH_LUBBOCK=y
-CONFIG_MACH_MAINSTONE=y
-CONFIG_MACH_ZYLONITE300=y
-CONFIG_MACH_ZYLONITE320=y
-CONFIG_MACH_LITTLETON=y
-CONFIG_MACH_TAVOREVB=y
-CONFIG_MACH_SAAR=y
-CONFIG_ARCH_PXA_IDP=y
-CONFIG_ARCH_VIPER=y
-CONFIG_MACH_ARCOM_ZEUS=y
-CONFIG_MACH_BALLOON3=y
-CONFIG_MACH_CSB726=y
-CONFIG_CSB726_CSB701=y
-CONFIG_MACH_EXEDA=y
-CONFIG_MACH_CM_X300=y
-CONFIG_MACH_CAPC7117=y
 CONFIG_ARCH_GUMSTIX=y
-CONFIG_MACH_INTELMOTE2=y
-CONFIG_MACH_STARGATE2=y
-CONFIG_MACH_XCEP=y
-CONFIG_TRIZEPS_PXA=y
-CONFIG_MACH_TRIZEPS4WL=y
-CONFIG_MACH_LOGICPD_PXA270=y
-CONFIG_MACH_PCM027=y
-CONFIG_MACH_PCM990_BASEBOARD=y
-CONFIG_MACH_COLIBRI=y
-CONFIG_MACH_COLIBRI_PXA270_INCOME=y
-CONFIG_MACH_COLIBRI300=y
-CONFIG_MACH_COLIBRI320=y
-CONFIG_MACH_COLIBRI_EVALBOARD=y
-CONFIG_MACH_VPAC270=y
-CONFIG_MACH_H4700=y
-CONFIG_MACH_H5000=y
-CONFIG_MACH_HIMALAYA=y
-CONFIG_MACH_MAGICIAN=y
-CONFIG_MACH_MIOA701=y
-CONFIG_PXA_EZX=y
-CONFIG_MACH_MP900C=y
-CONFIG_ARCH_PXA_PALM=y
 CONFIG_PXA_SHARPSL=y
-CONFIG_MACH_POODLE=y
-CONFIG_MACH_CORGI=y
-CONFIG_MACH_SHEPHERD=y
-CONFIG_MACH_HUSKY=y
 CONFIG_MACH_AKITA=y
 CONFIG_MACH_BORZOI=y
-CONFIG_MACH_TOSA=y
-CONFIG_TOSA_BT=m
-CONFIG_TOSA_USE_EXT_KEYCODES=y
-CONFIG_MACH_ICONTROL=y
-CONFIG_ARCH_PXA_ESERIES=y
-CONFIG_MACH_ZIPIT2=y
-CONFIG_PCI=y
-CONFIG_PCI_MSI=y
-CONFIG_PCIEPORTBUS=y
-CONFIG_PCCARD=m
-CONFIG_YENTA=m
-CONFIG_PCMCIA_PXA2XX=m
-CONFIG_PREEMPT=y
+CONFIG_PXA_SYSTEMS_CPLDS=y
 CONFIG_AEABI=y
-# CONFIG_COMPACTION is not set
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_ARCH_FORCE_MAX_ORDER=9
 CONFIG_CMDLINE="root=/dev/ram0 ro"
 CONFIG_KEXEC=y
 CONFIG_CPU_FREQ=y
@@ -99,7 +34,23 @@ CONFIG_CPUFREQ_DT=m
 CONFIG_ARM_PXA2xx_CPUFREQ=m
 CONFIG_CPU_IDLE=y
 CONFIG_ARM_CPUIDLE=y
+CONFIG_CRYPTO_SHA1_ARM=m
+CONFIG_CRYPTO_SHA256_ARM=m
+CONFIG_CRYPTO_SHA512_ARM=m
+CONFIG_CRYPTO_AES_ARM=m
+CONFIG_KPROBES=y
+CONFIG_MODULES=y
+CONFIG_MODULE_FORCE_LOAD=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_MODULE_FORCE_UNLOAD=y
+CONFIG_MODVERSIONS=y
+CONFIG_MODULE_SRCVERSION_ALL=y
+CONFIG_PARTITION_ADVANCED=y
+CONFIG_LDM_PARTITION=y
+CONFIG_CMDLINE_PARTITION=y
 CONFIG_BINFMT_MISC=y
+CONFIG_SLOB=y
+# CONFIG_COMPACTION is not set
 CONFIG_NET=y
 CONFIG_PACKET=y
 CONFIG_UNIX=y
@@ -117,16 +68,6 @@ CONFIG_BRIDGE=m
 CONFIG_VLAN_8021Q=m
 CONFIG_IEEE802154=y
 CONFIG_DNS_RESOLVER=y
-CONFIG_IRDA=m
-CONFIG_IRLAN=m
-CONFIG_IRNET=m
-CONFIG_IRCOMM=m
-CONFIG_IRDA_ULTRA=y
-CONFIG_IRDA_CACHE_LAST_LSAP=y
-CONFIG_IRDA_FAST_RR=y
-CONFIG_IRDA_DEBUG=y
-CONFIG_IRTTY_SIR=m
-CONFIG_PXA_FICP=m
 CONFIG_BT=m
 CONFIG_BT_RFCOMM=m
 CONFIG_BT_RFCOMM_TTY=y
@@ -153,51 +94,60 @@ CONFIG_MAC80211=m
 CONFIG_RFKILL=y
 CONFIG_RFKILL_INPUT=y
 CONFIG_RFKILL_GPIO=m
+CONFIG_PCI=y
+CONFIG_PCIEPORTBUS=y
+CONFIG_PCI_MSI=y
+CONFIG_PCCARD=m
+CONFIG_YENTA=m
+CONFIG_PCMCIA_PXA2XX=m
 CONFIG_DEVTMPFS=y
 CONFIG_DEVTMPFS_MOUNT=y
 CONFIG_CONNECTOR=y
+CONFIG_MTD=y
+CONFIG_MTD_AR7_PARTS=m
+CONFIG_MTD_CMDLINE_PARTS=m
+CONFIG_MTD_OF_PARTS=m
+CONFIG_MTD_AFS_PARTS=m
 CONFIG_MTD_REDBOOT_PARTS=m
 CONFIG_MTD_REDBOOT_DIRECTORY_BLOCK=0
 CONFIG_MTD_REDBOOT_PARTS_UNALLOCATED=y
 CONFIG_MTD_REDBOOT_PARTS_READONLY=y
-CONFIG_MTD_CMDLINE_PARTS=m
-CONFIG_MTD_AFS_PARTS=m
-CONFIG_MTD_OF_PARTS=m
-CONFIG_MTD_AR7_PARTS=m
 CONFIG_MTD_BLOCK=m
 CONFIG_NFTL=m
 CONFIG_NFTL_RW=y
+CONFIG_MTD_CFI=y
 CONFIG_MTD_JEDECPROBE=m
 CONFIG_MTD_CFI_ADV_OPTIONS=y
 CONFIG_MTD_CFI_LE_BYTE_SWAP=y
 CONFIG_MTD_CFI_GEOMETRY=y
 CONFIG_MTD_OTP=y
+CONFIG_MTD_CFI_INTELEXT=y
 CONFIG_MTD_CFI_AMDSTD=m
 CONFIG_MTD_CFI_STAA=m
 CONFIG_MTD_RAM=m
 CONFIG_MTD_ROM=m
 CONFIG_MTD_COMPLEX_MAPPINGS=y
+CONFIG_MTD_PHYSMAP=y
 CONFIG_MTD_PXA2XX=m
 CONFIG_MTD_M25P80=m
 CONFIG_MTD_BLOCK2MTD=y
 CONFIG_MTD_DOCG3=m
+CONFIG_MTD_ONENAND=m
+CONFIG_MTD_ONENAND_VERIFY_WRITE=y
+CONFIG_MTD_ONENAND_GENERIC=m
 CONFIG_MTD_RAW_NAND=m
-CONFIG_MTD_NAND_ECC_SW_BCH=y
+CONFIG_MTD_NAND_SHARPSL=m
+CONFIG_MTD_NAND_TMIO=m
+CONFIG_MTD_NAND_BRCMNAND=m
 CONFIG_MTD_NAND_GPIO=m
+CONFIG_MTD_NAND_PLATFORM=m
 CONFIG_MTD_NAND_DISKONCHIP=m
 CONFIG_MTD_NAND_DISKONCHIP_PROBE_ADVANCED=y
 CONFIG_MTD_NAND_DISKONCHIP_PROBE_ADDRESS=0x4000000
 CONFIG_MTD_NAND_DISKONCHIP_PROBE_HIGH=y
 CONFIG_MTD_NAND_DISKONCHIP_BBTWRITE=y
-CONFIG_MTD_NAND_SHARPSL=m
-CONFIG_MTD_NAND_MARVELL=m
 CONFIG_MTD_NAND_CM_X270=m
-CONFIG_MTD_NAND_TMIO=m
-CONFIG_MTD_NAND_BRCMNAND=m
-CONFIG_MTD_NAND_PLATFORM=m
-CONFIG_MTD_ONENAND=m
-CONFIG_MTD_ONENAND_VERIFY_WRITE=y
-CONFIG_MTD_ONENAND_GENERIC=m
+CONFIG_MTD_NAND_ECC_SW_BCH=y
 CONFIG_MTD_SPI_NOR=m
 CONFIG_MTD_UBI=m
 CONFIG_MTD_UBI_BLOCK=y
@@ -211,8 +161,6 @@ CONFIG_AD525X_DPOT_I2C=m
 CONFIG_ICS932S401=m
 CONFIG_APDS9802ALS=m
 CONFIG_ISL29003=m
-CONFIG_IIO=m
-CONFIG_AD5446=m
 CONFIG_EEPROM_AT24=m
 CONFIG_SENSORS_LIS3_SPI=m
 CONFIG_SCSI=y
@@ -243,13 +191,13 @@ CONFIG_SMC91X=m
 CONFIG_SMSC911X=m
 CONFIG_STMMAC_ETH=m
 CONFIG_PHYLIB=y
-CONFIG_AT803X_PHY=m
-CONFIG_MARVELL_PHY=m
 CONFIG_SMSC_PHY=m
 CONFIG_BROADCOM_PHY=y
 CONFIG_ICPLUS_PHY=m
 CONFIG_MICREL_PHY=m
 CONFIG_FIXED_PHY=m
+CONFIG_MARVELL_PHY=m
+CONFIG_AT803X_PHY=m
 CONFIG_MDIO_BITBANG=y
 CONFIG_PPP=m
 CONFIG_PPP_BSDCOMP=m
@@ -273,16 +221,16 @@ CONFIG_HOSTAP=m
 CONFIG_HOSTAP_FIRMWARE=y
 CONFIG_HOSTAP_FIRMWARE_NVRAM=y
 CONFIG_HOSTAP_CS=m
-CONFIG_LIBERTAS=m
-CONFIG_LIBERTAS_SDIO=m
 CONFIG_HERMES=m
 CONFIG_PCMCIA_HERMES=m
 CONFIG_PCMCIA_SPECTRUM=m
+CONFIG_LIBERTAS=m
+CONFIG_LIBERTAS_SDIO=m
+CONFIG_MWIFIEX=m
+CONFIG_MWIFIEX_SDIO=m
 CONFIG_RT2X00=m
 CONFIG_RT73USB=m
 CONFIG_RT2800USB=m
-CONFIG_MWIFIEX=m
-CONFIG_MWIFIEX_SDIO=m
 CONFIG_INPUT_FF_MEMLESS=m
 CONFIG_INPUT_MATRIXKMAP=y
 CONFIG_INPUT_MOUSEDEV=m
@@ -295,14 +243,12 @@ CONFIG_KEYBOARD_ATKBD=m
 CONFIG_KEYBOARD_QT1070=m
 CONFIG_KEYBOARD_GPIO=m
 CONFIG_KEYBOARD_PXA27x=m
-CONFIG_KEYBOARD_PXA930_ROTARY=m
 CONFIG_KEYBOARD_CROS_EC=m
 CONFIG_MOUSE_PS2=m
 CONFIG_MOUSE_PS2_ELANTECH=y
 CONFIG_MOUSE_SERIAL=m
 CONFIG_MOUSE_CYAPA=m
 CONFIG_MOUSE_ELAN_I2C=m
-CONFIG_MOUSE_PXA930_TRKBALL=m
 CONFIG_MOUSE_NAVPOINT_PXA27x=m
 CONFIG_INPUT_TOUCHSCREEN=y
 CONFIG_TOUCHSCREEN_ADS7846=m
@@ -313,12 +259,9 @@ CONFIG_TOUCHSCREEN_FUJITSU=m
 CONFIG_TOUCHSCREEN_ELO=m
 CONFIG_TOUCHSCREEN_MTOUCH=m
 CONFIG_TOUCHSCREEN_INEXIO=m
-CONFIG_TOUCHSCREEN_HTCPEN=m
 CONFIG_TOUCHSCREEN_PENMOUNT=m
 CONFIG_TOUCHSCREEN_TOUCHRIGHT=m
 CONFIG_TOUCHSCREEN_TOUCHWIN=m
-CONFIG_TOUCHSCREEN_UCB1400=m
-CONFIG_TOUCHSCREEN_WM97XX=m
 CONFIG_TOUCHSCREEN_TOUCHIT213=m
 CONFIG_TOUCHSCREEN_PCAP=m
 CONFIG_TOUCHSCREEN_ST1232=m
@@ -329,7 +272,6 @@ CONFIG_INPUT_GPIO_ROTARY_ENCODER=m
 CONFIG_INPUT_PCAP=m
 CONFIG_INPUT_ADXL34X=m
 CONFIG_SERIO=m
-CONFIG_SERIO_SA1111=m
 CONFIG_LEGACY_PTY_COUNT=8
 CONFIG_SERIAL_8250=m
 CONFIG_SERIAL_8250_CS=m
@@ -342,6 +284,7 @@ CONFIG_I2C_CHARDEV=m
 CONFIG_I2C_MUX_PCA954x=m
 CONFIG_I2C_MUX_PINCTRL=m
 CONFIG_I2C_DESIGNWARE_PLATFORM=m
+CONFIG_I2C_GPIO=y
 CONFIG_I2C_PXA_SLAVE=y
 CONFIG_I2C_XILINX=m
 CONFIG_I2C_CROS_EC_TUNNEL=m
@@ -355,16 +298,17 @@ CONFIG_SPI_XILINX=m
 CONFIG_SPI_SPIDEV=m
 CONFIG_PPS=y
 CONFIG_DEBUG_GPIO=y
+CONFIG_GPIO_SYSFS=y
 CONFIG_GPIO_DWAPB=m
 CONFIG_GPIO_GENERIC_PLATFORM=m
 CONFIG_GPIO_MAX732X=m
 CONFIG_GPIO_PCA953X=m
 CONFIG_GPIO_PCF857X=m
+CONFIG_HTC_EGPIO=y
 CONFIG_GPIO_PALMAS=y
 CONFIG_GPIO_TPS6586X=y
 CONFIG_GPIO_TPS65910=y
 CONFIG_GPIO_MAX7301=m
-CONFIG_GPIO_SYSFS=y
 CONFIG_POWER_SUPPLY_DEBUG=y
 CONFIG_PDA_POWER=m
 CONFIG_BATTERY_SBS=m
@@ -388,13 +332,8 @@ CONFIG_MFD_AS3711=y
 CONFIG_MFD_BCM590XX=m
 CONFIG_MFD_AXP20X=y
 CONFIG_MFD_CROS_EC_DEV=m
-CONFIG_CHROME_PLATFORMS=y
-CONFIG_CROS_EC=m
-CONFIG_CROS_EC_I2C=m
-CONFIG_CROS_EC_SPI=m
 CONFIG_MFD_ASIC3=y
 CONFIG_PMIC_DA903X=y
-CONFIG_HTC_EGPIO=y
 CONFIG_HTC_PASIC3=m
 CONFIG_MFD_MAX14577=y
 CONFIG_MFD_MAX77693=y
@@ -442,11 +381,13 @@ CONFIG_VIDEO_V4L2_SUBDEV_API=y
 CONFIG_MEDIA_USB_SUPPORT=y
 CONFIG_USB_VIDEO_CLASS=m
 CONFIG_V4L_PLATFORM_DRIVERS=y
-CONFIG_VIDEO_PXA27x=m
 CONFIG_V4L_MEM2MEM_DRIVERS=y
+CONFIG_VIDEO_PXA27x=m
 CONFIG_DRM=m
+CONFIG_FB=y
 CONFIG_FIRMWARE_EDID=y
 CONFIG_FB_TILEBLITTING=y
+CONFIG_FB_PXA=y
 CONFIG_FB_PXA_OVERLAY=y
 CONFIG_FB_PXA_PARAMETERS=y
 CONFIG_PXA3XX_GCU=m
@@ -463,32 +404,20 @@ CONFIG_FRAMEBUFFER_CONSOLE_ROTATION=y
 CONFIG_LOGO=y
 CONFIG_SOUND=m
 CONFIG_SND=m
-CONFIG_SND_SEQUENCER=m
 CONFIG_SND_MIXER_OSS=m
 CONFIG_SND_PCM_OSS=m
 CONFIG_SND_DYNAMIC_MINORS=y
 CONFIG_SND_VERBOSE_PRINTK=y
 CONFIG_SND_DEBUG=y
+CONFIG_SND_SEQUENCER=m
 CONFIG_SND_USB_AUDIO=m
 CONFIG_SND_SOC=m
 CONFIG_SND_ATMEL_SOC=m
 CONFIG_SND_PXA2XX_SOC=m
-CONFIG_SND_PXA2XX_SOC_CORGI=m
+CONFIG_SND_PXA_SOC_SSP=m
 CONFIG_SND_PXA2XX_SOC_SPITZ=m
-CONFIG_SND_PXA2XX_SOC_Z2=m
-CONFIG_SND_PXA2XX_SOC_POODLE=m
-CONFIG_SND_PXA2XX_SOC_TOSA=m
-CONFIG_SND_PXA2XX_SOC_E740=m
-CONFIG_SND_PXA2XX_SOC_E750=m
-CONFIG_SND_PXA2XX_SOC_E800=m
-CONFIG_SND_PXA2XX_SOC_EM_X270=m
-CONFIG_SND_PXA2XX_SOC_PALM27X=y
-CONFIG_SND_SOC_ZYLONITE=m
-CONFIG_SND_PXA2XX_SOC_HX4700=m
-CONFIG_SND_PXA2XX_SOC_MAGICIAN=m
-CONFIG_SND_PXA2XX_SOC_MIOA701=m
-CONFIG_SND_PXA2XX_SOC_IMOTE2=m
 CONFIG_SND_SOC_AK4642=m
+CONFIG_SND_SOC_WM8731_I2C=m
 CONFIG_SND_SOC_WM8978=m
 CONFIG_SND_SIMPLE_CARD=m
 CONFIG_SOUND_PRIME=m
@@ -577,6 +506,7 @@ CONFIG_USB_LCD=m
 CONFIG_USB_CYTHERM=m
 CONFIG_USB_IDMOUSE=m
 CONFIG_USB_GPIO_VBUS=y
+CONFIG_USB_GPIO_VBUS=m
 CONFIG_USB_ISP1301=m
 CONFIG_USB_GADGET=m
 CONFIG_USB_GADGET_VBUS_DRAW=500
@@ -623,9 +553,9 @@ CONFIG_RTC_DRV_DS1307=m
 CONFIG_RTC_DRV_MAX8907=m
 CONFIG_RTC_DRV_RS5C372=m
 CONFIG_RTC_DRV_ISL1208=m
-CONFIG_RTC_DRV_PALMAS=m
 CONFIG_RTC_DRV_PCF8563=m
 CONFIG_RTC_DRV_PCF8583=m
+CONFIG_RTC_DRV_PALMAS=m
 CONFIG_RTC_DRV_TPS6586X=m
 CONFIG_RTC_DRV_TPS65910=m
 CONFIG_RTC_DRV_S35390A=m
@@ -640,10 +570,16 @@ CONFIG_PXA_DMA=y
 CONFIG_DW_DMAC=m
 CONFIG_UIO=y
 CONFIG_CROS_EC_CHARDEV=m
+CONFIG_CHROME_PLATFORMS=y
+CONFIG_CROS_EC=m
+CONFIG_CROS_EC_I2C=m
+CONFIG_CROS_EC_SPI=m
 CONFIG_COMMON_CLK_S2MPS11=m
 CONFIG_PM_DEVFREQ=y
 CONFIG_EXTCON=y
 CONFIG_MEMORY=y
+CONFIG_IIO=m
+CONFIG_AD5446=m
 CONFIG_PWM=y
 CONFIG_PWM_PXA=m
 CONFIG_PHY_SAMSUNG_USB2=m
@@ -699,7 +635,6 @@ CONFIG_NFSD_V3_ACL=y
 CONFIG_NFSD_V4=y
 CONFIG_CIFS=m
 CONFIG_CIFS_STATS=y
-CONFIG_CIFS_WEAK_PW_HASH=y
 CONFIG_CIFS_XATTR=y
 CONFIG_CIFS_POSIX=y
 CONFIG_NLS_DEFAULT="utf8"
@@ -710,17 +645,7 @@ CONFIG_NLS_ASCII=m
 CONFIG_NLS_ISO8859_1=m
 CONFIG_NLS_ISO8859_15=m
 CONFIG_NLS_UTF8=m
-CONFIG_PRINTK_TIME=y
-CONFIG_DYNAMIC_DEBUG=y
-CONFIG_DEBUG_INFO=y
-CONFIG_FRAME_WARN=0
-CONFIG_STRIP_ASM_SYMS=y
-CONFIG_MAGIC_SYSRQ=y
-CONFIG_DEBUG_SHIRQ=y
 CONFIG_TIMER_STATS=y
-CONFIG_FUNCTION_TRACER=y
-CONFIG_FTRACE_SYSCALLS=y
-CONFIG_DEBUG_USER=y
 CONFIG_SECURITY=y
 CONFIG_CRYPTO_MANAGER=y
 CONFIG_CRYPTO_CRYPTD=m
@@ -746,11 +671,6 @@ CONFIG_CRYPTO_TEA=m
 CONFIG_CRYPTO_TWOFISH=m
 CONFIG_CRYPTO_DEFLATE=y
 CONFIG_CRYPTO_LZO=y
-CONFIG_ARM_CRYPTO=y
-CONFIG_CRYPTO_SHA1_ARM=m
-CONFIG_CRYPTO_SHA256_ARM=m
-CONFIG_CRYPTO_SHA512_ARM=m
-CONFIG_CRYPTO_AES_ARM=m
 CONFIG_CRC_CCITT=y
 CONFIG_CRC_T10DIF=m
 CONFIG_FONTS=y
@@ -758,3 +678,12 @@ CONFIG_FONT_8x8=y
 CONFIG_FONT_8x16=y
 CONFIG_FONT_6x11=y
 CONFIG_FONT_MINI_4x6=y
+CONFIG_PRINTK_TIME=y
+CONFIG_DYNAMIC_DEBUG=y
+CONFIG_DEBUG_INFO_DWARF_TOOLCHAIN_DEFAULT=y
+CONFIG_FRAME_WARN=0
+CONFIG_STRIP_ASM_SYMS=y
+CONFIG_MAGIC_SYSRQ=y
+CONFIG_DEBUG_SHIRQ=y
+CONFIG_FUNCTION_TRACER=y
+CONFIG_FTRACE_SYSCALLS=y
diff --git a/arch/arm/configs/qcom_defconfig b/arch/arm/configs/qcom_defconfig
index 0daa9c0d298e..7d8b6884fd00 100644
--- a/arch/arm/configs/qcom_defconfig
+++ b/arch/arm/configs/qcom_defconfig
@@ -1,40 +1,38 @@
 CONFIG_SYSVIPC=y
-CONFIG_NO_HZ=y
+CONFIG_NO_HZ_IDLE=y
 CONFIG_HIGH_RES_TIMERS=y
+CONFIG_PREEMPT=y
 CONFIG_IKCONFIG=y
 CONFIG_IKCONFIG_PROC=y
 CONFIG_CGROUPS=y
 CONFIG_BLK_DEV_INITRD=y
 CONFIG_KALLSYMS_ALL=y
 CONFIG_EMBEDDED=y
-# CONFIG_SLUB_DEBUG is not set
-# CONFIG_COMPAT_BRK is not set
 CONFIG_PROFILING=y
-CONFIG_KPROBES=y
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
-CONFIG_MODULE_FORCE_UNLOAD=y
-CONFIG_MODVERSIONS=y
-CONFIG_PARTITION_ADVANCED=y
 CONFIG_ARCH_QCOM=y
 CONFIG_ARCH_MSM8X60=y
 CONFIG_ARCH_MSM8960=y
 CONFIG_ARCH_MSM8974=y
 CONFIG_ARCH_MDM9615=y
-CONFIG_PCI=y
-CONFIG_PCI_MSI=y
-CONFIG_PCIE_QCOM=y
 CONFIG_SMP=y
-CONFIG_PREEMPT=y
+CONFIG_ARM_PSCI=y
 CONFIG_HIGHMEM=y
-CONFIG_CLEANCACHE=y
 CONFIG_ARM_APPENDED_DTB=y
 CONFIG_ARM_ATAG_DTB_COMPAT=y
+CONFIG_CPU_FREQ=y
+CONFIG_CPUFREQ_DT=y
 CONFIG_CPU_IDLE=y
 CONFIG_ARM_CPUIDLE=y
 CONFIG_VFP=y
 CONFIG_NEON=y
+CONFIG_KPROBES=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_MODULE_FORCE_UNLOAD=y
+CONFIG_MODVERSIONS=y
+CONFIG_PARTITION_ADVANCED=y
 # CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+# CONFIG_COMPAT_BRK is not set
 CONFIG_CMA=y
 CONFIG_NET=y
 CONFIG_PACKET=y
@@ -57,15 +55,18 @@ CONFIG_BT_HCIUART_BCM=y
 CONFIG_CFG80211=m
 CONFIG_MAC80211=m
 CONFIG_RFKILL=y
+CONFIG_PCI=y
+CONFIG_PCI_MSI=y
+CONFIG_PCIE_QCOM=y
 CONFIG_DEVTMPFS=y
 CONFIG_DEVTMPFS_MOUNT=y
 CONFIG_MTD=y
+CONFIG_MTD_QCOMSMEM_PARTS=y
 CONFIG_MTD_BLOCK=y
 CONFIG_MTD_M25P80=y
 CONFIG_MTD_RAW_NAND=y
 CONFIG_MTD_NAND_QCOM=y
 CONFIG_MTD_SPI_NOR=y
-CONFIG_MTD_QCOMSMEM_PARTS=y
 CONFIG_MTD_UBI=y
 CONFIG_BLK_DEV_LOOP=y
 CONFIG_BLK_DEV_RAM=y
@@ -134,10 +135,10 @@ CONFIG_PINCTRL_MSM8660=y
 CONFIG_PINCTRL_MSM8960=y
 CONFIG_PINCTRL_MDM9615=y
 CONFIG_PINCTRL_MSM8X74=y
-CONFIG_PINCTRL_SDX55=y
 CONFIG_PINCTRL_QCOM_SPMI_PMIC=y
 CONFIG_PINCTRL_QCOM_SSBI_PMIC=y
 CONFIG_GPIOLIB=y
+CONFIG_PINCTRL_SDX55=y
 CONFIG_GPIO_SYSFS=y
 CONFIG_POWER_RESET=y
 CONFIG_POWER_RESET_MSM=y
@@ -145,15 +146,17 @@ CONFIG_CHARGER_QCOM_SMBB=y
 CONFIG_CHARGER_BQ24190=m
 CONFIG_THERMAL=y
 CONFIG_QCOM_TSENS=y
+CONFIG_WATCHDOG=y
+CONFIG_QCOM_WDT=y
 CONFIG_MFD_PM8XXX=y
 CONFIG_MFD_QCOM_RPM=y
 CONFIG_MFD_SPMI_PMIC=y
 CONFIG_REGULATOR=y
 CONFIG_REGULATOR_FIXED_VOLTAGE=y
 CONFIG_REGULATOR_QCOM_RPM=y
+CONFIG_REGULATOR_QCOM_RPMH=y
 CONFIG_REGULATOR_QCOM_SMD_RPM=y
 CONFIG_REGULATOR_QCOM_SPMI=y
-CONFIG_REGULATOR_QCOM_RPMH=y
 CONFIG_MEDIA_SUPPORT=y
 CONFIG_DRM=y
 CONFIG_DRM_MSM=m
@@ -161,11 +164,11 @@ CONFIG_DRM_PANEL_SIMPLE=y
 CONFIG_DRM_PANEL_EDP=y
 CONFIG_DRM_ANALOGIX_ANX78XX=m
 CONFIG_FB=y
-CONFIG_FRAMEBUFFER_CONSOLE=y
 # CONFIG_LCD_CLASS_DEVICE is not set
 CONFIG_BACKLIGHT_CLASS_DEVICE=y
 CONFIG_BACKLIGHT_LM3630A=y
 CONFIG_BACKLIGHT_LP855X=y
+CONFIG_FRAMEBUFFER_CONSOLE=y
 CONFIG_SOUND=y
 CONFIG_SND=y
 CONFIG_SND_DYNAMIC_MINORS=y
@@ -181,6 +184,7 @@ CONFIG_USB_MON=y
 CONFIG_USB_EHCI_HCD=y
 CONFIG_USB_EHCI_MSM=y
 CONFIG_USB_ACM=y
+CONFIG_USB_DWC3=y
 CONFIG_USB_CHIPIDEA=y
 CONFIG_USB_CHIPIDEA_UDC=y
 CONFIG_USB_CHIPIDEA_HOST=y
@@ -197,7 +201,6 @@ CONFIG_USB_CONFIGFS_ECM=y
 CONFIG_USB_CONFIGFS_F_FS=y
 CONFIG_USB_ULPI_BUS=y
 CONFIG_USB_ETH=m
-CONFIG_USB_DWC3=y
 CONFIG_MMC=y
 CONFIG_MMC_BLOCK_MINORS=32
 CONFIG_MMC_ARMMMCI=y
@@ -219,8 +222,8 @@ CONFIG_COMMON_CLK_QCOM=y
 CONFIG_QCOM_A7PLL=y
 CONFIG_QCOM_CLK_APCS_SDX55=y
 CONFIG_QCOM_CLK_RPM=y
-CONFIG_QCOM_CLK_RPMH=y
 CONFIG_QCOM_CLK_SMD_RPM=y
+CONFIG_QCOM_CLK_RPMH=y
 CONFIG_APQ_MMCC_8084=y
 CONFIG_IPQ_GCC_4019=y
 CONFIG_IPQ_LCC_806X=y
@@ -230,30 +233,35 @@ CONFIG_MDM_LCC_9615=y
 CONFIG_MSM_MMCC_8960=y
 CONFIG_MSM_MMCC_8974=y
 CONFIG_SDX_GCC_55=y
-CONFIG_MSM_IOMMU=y
-CONFIG_ARM_SMMU=y
 CONFIG_HWSPINLOCK=y
 CONFIG_HWSPINLOCK_QCOM=y
 CONFIG_MAILBOX=y
 CONFIG_QCOM_APCS_IPC=y
+CONFIG_MSM_IOMMU=y
+CONFIG_ARM_SMMU=y
 CONFIG_REMOTEPROC=y
 CONFIG_QCOM_ADSP_PIL=y
 CONFIG_QCOM_Q6V5_PAS=y
 CONFIG_QCOM_Q6V5_PIL=y
 CONFIG_QCOM_WCNSS_PIL=y
 CONFIG_RPMSG_CHAR=y
+CONFIG_RPMSG_CTRL=y
 CONFIG_RPMSG_QCOM_GLINK_SMEM=y
 CONFIG_RPMSG_QCOM_SMD=y
 CONFIG_QCOM_COMMAND_DB=y
 CONFIG_QCOM_GSBI=y
 CONFIG_QCOM_OCMEM=y
 CONFIG_QCOM_PM=y
+CONFIG_QCOM_RPMH=y
+CONFIG_QCOM_RPMHPD=y
+CONFIG_QCOM_RMTFS_MEM=y
+CONFIG_QCOM_RPMPD=y
 CONFIG_QCOM_SMEM=y
 CONFIG_QCOM_SMD_RPM=y
 CONFIG_QCOM_SMP2P=y
 CONFIG_QCOM_SMSM=y
-CONFIG_QCOM_RPMH=y
-CONFIG_QCOM_RPMHPD=y
+CONFIG_QCOM_SOCINFO=y
+CONFIG_QCOM_STATS=y
 CONFIG_QCOM_WCNSS_CTRL=y
 CONFIG_EXTCON_QCOM_SPMI_MISC=y
 CONFIG_IIO=y
@@ -271,11 +279,11 @@ CONFIG_BMP280=y
 CONFIG_PWM=y
 CONFIG_PHY_QCOM_APQ8064_SATA=y
 CONFIG_PHY_QCOM_IPQ806X_SATA=y
-CONFIG_PHY_QCOM_USB_HS=y
-CONFIG_PHY_QCOM_USB_HSIC=y
 CONFIG_PHY_QCOM_QMP=y
+CONFIG_PHY_QCOM_USB_HS=y
 CONFIG_PHY_QCOM_USB_SNPS_FEMTO_V2=y
-CONFIG_QCOM_QFPROM=y
+CONFIG_PHY_QCOM_USB_HSIC=y
+CONFIG_NVMEM_QCOM_QFPROM=y
 CONFIG_INTERCONNECT=y
 CONFIG_INTERCONNECT_QCOM=y
 CONFIG_INTERCONNECT_QCOM_MSM8974=m
@@ -296,15 +304,19 @@ CONFIG_NLS_CODEPAGE_437=y
 CONFIG_NLS_ASCII=y
 CONFIG_NLS_ISO8859_1=y
 CONFIG_NLS_UTF8=y
+CONFIG_CRYPTO_USER=m
+CONFIG_CRYPTO_USER_API=m
+CONFIG_CRYPTO_USER_API_HASH=m
+CONFIG_CRYPTO_USER_API_SKCIPHER=m
+CONFIG_CRYPTO_USER_API_RNG=m
+CONFIG_CRYPTO_USER_API_AEAD=m
+CONFIG_CRYPTO_DEV_QCOM_RNG=m
 CONFIG_DMA_CMA=y
 CONFIG_CMA_SIZE_MBYTES=64
 CONFIG_PRINTK_TIME=y
 CONFIG_DYNAMIC_DEBUG=y
-CONFIG_DEBUG_INFO=y
+CONFIG_DEBUG_INFO_DWARF_TOOLCHAIN_DEFAULT=y
 CONFIG_MAGIC_SYSRQ=y
+CONFIG_DEBUG_FS=y
+# CONFIG_SLUB_DEBUG is not set
 # CONFIG_SCHED_DEBUG is not set
-CONFIG_WATCHDOG=y
-CONFIG_QCOM_WDT=y
-CONFIG_ARM_PSCI=y
-CONFIG_CPU_FREQ=y
-CONFIG_CPUFREQ_DT=y
diff --git a/arch/arm/configs/realview_defconfig b/arch/arm/configs/realview_defconfig
index 3ef3521c19db..92f803c2805c 100644
--- a/arch/arm/configs/realview_defconfig
+++ b/arch/arm/configs/realview_defconfig
@@ -1,10 +1,8 @@
-# CONFIG_SWAP is not set
 CONFIG_SYSVIPC=y
 CONFIG_NO_HZ_FULL=y
 CONFIG_HIGH_RES_TIMERS=y
 CONFIG_LOG_BUF_SHIFT=14
 CONFIG_PERF_EVENTS=y
-CONFIG_SLAB=y
 CONFIG_ARCH_MULTI_V6=y
 CONFIG_ARCH_REALVIEW=y
 CONFIG_MACH_REALVIEW_EB=y
@@ -21,7 +19,8 @@ CONFIG_CMDLINE="root=/dev/nfs nfsroot=10.1.69.3:/work/nfsroot ip=dhcp console=tt
 CONFIG_VFP=y
 CONFIG_MODULES=y
 CONFIG_MODULE_UNLOAD=y
-# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_SWAP is not set
+CONFIG_SLAB=y
 CONFIG_CMA=y
 CONFIG_NET=y
 CONFIG_PACKET=y
@@ -43,6 +42,7 @@ CONFIG_MTD_PHYSMAP=y
 CONFIG_MTD_PHYSMAP_OF=y
 CONFIG_SCSI=y
 CONFIG_BLK_DEV_SD=y
+# CONFIG_BLK_DEV_BSG is not set
 CONFIG_NETDEVICES=y
 CONFIG_SMC91X=y
 CONFIG_SMSC911X=y
@@ -95,9 +95,9 @@ CONFIG_NFS_FS=y
 CONFIG_ROOT_NFS=y
 CONFIG_NLS_CODEPAGE_437=y
 CONFIG_NLS_ISO8859_1=y
+CONFIG_DEBUG_KERNEL=y
 CONFIG_MAGIC_SYSRQ=y
 CONFIG_DEBUG_FS=y
-CONFIG_DEBUG_KERNEL=y
 # CONFIG_SCHED_DEBUG is not set
 # CONFIG_FTRACE is not set
 CONFIG_DEBUG_USER=y
diff --git a/arch/arm/configs/rpc_defconfig b/arch/arm/configs/rpc_defconfig
index c090643b1ecb..210974364d61 100644
--- a/arch/arm/configs/rpc_defconfig
+++ b/arch/arm/configs/rpc_defconfig
@@ -2,16 +2,16 @@
 CONFIG_SYSVIPC=y
 CONFIG_LOG_BUF_SHIFT=14
 CONFIG_BLK_DEV_INITRD=y
-CONFIG_SLAB=y
 CONFIG_MODULES=y
 CONFIG_MODULE_UNLOAD=y
-# CONFIG_BLK_DEV_BSG is not set
+CONFIG_ARCH_MULTI_V4=y
+# CONFIG_ARCH_MULTI_V7 is not set
 CONFIG_ARCH_RPC=y
 CONFIG_CPU_SA110=y
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
 CONFIG_FPE_NWFPE=y
-CONFIG_BINFMT_AOUT=y
+CONFIG_PARTITION_ADVANCED=y
+CONFIG_BSD_DISKLABEL=y
+CONFIG_SLAB=y
 CONFIG_NET=y
 CONFIG_PACKET=y
 CONFIG_UNIX=y
@@ -33,6 +33,7 @@ CONFIG_BLK_DEV_SD=y
 CONFIG_CHR_DEV_ST=m
 CONFIG_BLK_DEV_SR=y
 CONFIG_CHR_DEV_SG=y
+# CONFIG_BLK_DEV_BSG is not set
 CONFIG_SCSI_CONSTANTS=y
 CONFIG_SCSI_LOGGING=y
 CONFIG_SCSI_ARXESCSI=m
@@ -55,12 +56,12 @@ CONFIG_INPUT_EVDEV=y
 # CONFIG_MOUSE_PS2 is not set
 CONFIG_MOUSE_RISCPC=y
 # CONFIG_SERIO_SERPORT is not set
+CONFIG_LEGACY_PTY_COUNT=64
 CONFIG_SERIAL_8250=y
 CONFIG_SERIAL_8250_CONSOLE=y
 CONFIG_SERIAL_8250_NR_UARTS=16
 CONFIG_SERIAL_8250_RUNTIME_UARTS=8
 CONFIG_SERIAL_8250_ACORN=y
-CONFIG_LEGACY_PTY_COUNT=64
 CONFIG_PRINTER=m
 # CONFIG_HW_RANDOM is not set
 CONFIG_I2C=y
@@ -69,9 +70,6 @@ CONFIG_I2C_CHARDEV=y
 CONFIG_FB=y
 CONFIG_FB_ACORN=y
 CONFIG_FRAMEBUFFER_CONSOLE=y
-CONFIG_FONTS=y
-CONFIG_FONT_8x16=y
-CONFIG_FONT_ACORN_8x8=y
 CONFIG_LOGO=y
 CONFIG_SOUND=m
 CONFIG_SOUND_PRIME=m
@@ -89,10 +87,8 @@ CONFIG_MSDOS_FS=m
 CONFIG_VFAT_FS=m
 CONFIG_ADFS_FS=y
 CONFIG_NFS_FS=y
-CONFIG_PARTITION_ADVANCED=y
 # CONFIG_ACORN_PARTITION_CUMANA is not set
 # CONFIG_ACORN_PARTITION_EESOX is not set
-CONFIG_BSD_DISKLABEL=y
 CONFIG_NLS_CODEPAGE_437=m
 CONFIG_NLS_CODEPAGE_737=m
 CONFIG_NLS_CODEPAGE_775=m
@@ -120,8 +116,11 @@ CONFIG_NLS_ISO8859_6=m
 CONFIG_NLS_ISO8859_7=m
 CONFIG_NLS_ISO8859_9=m
 CONFIG_NLS_KOI8_R=m
-CONFIG_MAGIC_SYSRQ=y
+CONFIG_FONTS=y
+CONFIG_FONT_8x16=y
+CONFIG_FONT_ACORN_8x8=y
 CONFIG_DEBUG_KERNEL=y
+CONFIG_MAGIC_SYSRQ=y
 CONFIG_DEBUG_USER=y
 CONFIG_DEBUG_LL=y
 CONFIG_DEBUG_LL_UART_8250=y
diff --git a/arch/arm/configs/s3c2410_defconfig b/arch/arm/configs/s3c2410_defconfig
index 153009130dab..41b40863a78e 100644
--- a/arch/arm/configs/s3c2410_defconfig
+++ b/arch/arm/configs/s3c2410_defconfig
@@ -3,7 +3,9 @@ CONFIG_IKCONFIG=m
 CONFIG_IKCONFIG_PROC=y
 CONFIG_LOG_BUF_SHIFT=16
 CONFIG_BLK_DEV_INITRD=y
-CONFIG_SLAB=y
+CONFIG_ARCH_MULTI_V4T=y
+CONFIG_ARCH_MULTI_V5=y
+# CONFIG_ARCH_MULTI_V7 is not set
 CONFIG_ARCH_S3C24XX=y
 CONFIG_S3C_ADC=y
 CONFIG_CPU_S3C2412=y
@@ -35,18 +37,17 @@ CONFIG_ARCH_S3C2440=y
 CONFIG_MACH_NEO1973_GTA02=y
 CONFIG_MACH_RX1950=y
 CONFIG_MACH_SMDK2443=y
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_UNUSED_BOARD_FILES=y
 CONFIG_CMDLINE="root=/dev/hda1 ro init=/bin/bash console=ttySAC0"
 CONFIG_FPE_NWFPE=y
 CONFIG_FPE_NWFPE_XP=y
 CONFIG_APM_EMULATION=m
 CONFIG_MODULES=y
 CONFIG_MODULE_UNLOAD=y
-# CONFIG_BLK_DEV_BSG is not set
 CONFIG_PARTITION_ADVANCED=y
 CONFIG_BSD_DISKLABEL=y
 CONFIG_SOLARIS_X86_PARTITION=y
+CONFIG_SLAB=y
 CONFIG_NET=y
 CONFIG_PACKET=y
 CONFIG_UNIX=y
@@ -203,6 +204,7 @@ CONFIG_BLK_DEV_SD=y
 CONFIG_CHR_DEV_ST=m
 CONFIG_BLK_DEV_SR=y
 CONFIG_CHR_DEV_SG=y
+# CONFIG_BLK_DEV_BSG is not set
 CONFIG_CHR_DEV_SCH=m
 CONFIG_SCSI_CONSTANTS=y
 CONFIG_SCSI_SCAN_ASYNC=y
@@ -249,7 +251,6 @@ CONFIG_INPUT_YEALINK=m
 CONFIG_INPUT_CM109=m
 CONFIG_INPUT_UINPUT=m
 CONFIG_INPUT_GPIO_ROTARY_ENCODER=m
-CONFIG_SERIAL_NONSTANDARD=y
 CONFIG_SERIAL_8250=y
 CONFIG_SERIAL_8250_CONSOLE=y
 CONFIG_SERIAL_8250_NR_UARTS=8
@@ -258,6 +259,7 @@ CONFIG_SERIAL_8250_MANY_PORTS=y
 CONFIG_SERIAL_8250_SHARE_IRQ=y
 CONFIG_SERIAL_SAMSUNG=y
 CONFIG_SERIAL_SAMSUNG_CONSOLE=y
+CONFIG_SERIAL_NONSTANDARD=y
 CONFIG_SERIAL_DEV_BUS=m
 CONFIG_PRINTER=y
 CONFIG_PPDEV=y
@@ -358,6 +360,8 @@ CONFIG_RTC_CLASS=y
 CONFIG_RTC_DRV_S3C=y
 CONFIG_DMADEVICES=y
 CONFIG_S3C24XX_DMAC=y
+CONFIG_PWM=y
+CONFIG_PWM_SAMSUNG=y
 CONFIG_EXT2_FS=y
 CONFIG_EXT2_FS_XATTR=y
 CONFIG_EXT2_FS_POSIX_ACL=y
@@ -425,9 +429,9 @@ CONFIG_NLS_ISO8859_15=m
 CONFIG_NLS_KOI8_R=m
 CONFIG_NLS_KOI8_U=m
 CONFIG_NLS_UTF8=m
-CONFIG_DEBUG_INFO=y
-CONFIG_MAGIC_SYSRQ=y
+CONFIG_DEBUG_INFO_DWARF_TOOLCHAIN_DEFAULT=y
 CONFIG_DEBUG_KERNEL=y
+CONFIG_MAGIC_SYSRQ=y
 CONFIG_DEBUG_MUTEXES=y
 CONFIG_DEBUG_USER=y
 CONFIG_DEBUG_LL=y
diff --git a/arch/arm/configs/s3c6400_defconfig b/arch/arm/configs/s3c6400_defconfig
index 59a258d504aa..93258d5b57ff 100644
--- a/arch/arm/configs/s3c6400_defconfig
+++ b/arch/arm/configs/s3c6400_defconfig
@@ -5,15 +5,6 @@ CONFIG_KALLSYMS_ALL=y
 CONFIG_ARCH_MULTI_V6=y
 # CONFIG_ARCH_MULTI_V7 is not set
 CONFIG_ARCH_S3C64XX=y
-CONFIG_MACH_SMDK6400=y
-CONFIG_MACH_ANW6410=y
-CONFIG_MACH_MINI6410=y
-CONFIG_MACH_REAL6410=y
-CONFIG_MACH_SMDK6410=y
-CONFIG_MACH_NCP=y
-CONFIG_MACH_HMT=y
-CONFIG_MACH_SMARTQ5=y
-CONFIG_MACH_SMARTQ7=y
 CONFIG_MACH_WLF_CRAGG_6410=y
 CONFIG_CMDLINE="console=ttySAC0,115200 root=/dev/ram init=/linuxrc initrd=0x51000000,6M ramdisk_size=6144"
 CONFIG_VFP=y
@@ -71,9 +62,9 @@ CONFIG_TMPFS=y
 CONFIG_TMPFS_POSIX_ACL=y
 CONFIG_CRAMFS=y
 CONFIG_ROMFS_FS=y
-CONFIG_DEBUG_INFO=y
-CONFIG_MAGIC_SYSRQ=y
 CONFIG_DEBUG_KERNEL=y
+CONFIG_DEBUG_INFO_DWARF_TOOLCHAIN_DEFAULT=y
+CONFIG_MAGIC_SYSRQ=y
 CONFIG_DEBUG_RT_MUTEXES=y
 CONFIG_DEBUG_SPINLOCK=y
 CONFIG_DEBUG_MUTEXES=y
diff --git a/arch/arm/configs/s5pv210_defconfig b/arch/arm/configs/s5pv210_defconfig
index 70919716f815..4c1e480b5bbd 100644
--- a/arch/arm/configs/s5pv210_defconfig
+++ b/arch/arm/configs/s5pv210_defconfig
@@ -1,5 +1,5 @@
 CONFIG_SYSVIPC=y
-CONFIG_NO_HZ=y
+CONFIG_NO_HZ_IDLE=y
 CONFIG_HIGH_RES_TIMERS=y
 CONFIG_PREEMPT=y
 CONFIG_CGROUPS=y
@@ -21,7 +21,6 @@ CONFIG_VFP=y
 CONFIG_NEON=y
 CONFIG_MODULES=y
 CONFIG_MODULE_UNLOAD=y
-# CONFIG_BLK_DEV_BSG is not set
 CONFIG_PARTITION_ADVANCED=y
 CONFIG_BSD_DISKLABEL=y
 CONFIG_SOLARIS_X86_PARTITION=y
@@ -48,6 +47,7 @@ CONFIG_BLK_DEV_RAM_SIZE=8192
 CONFIG_SCSI=y
 CONFIG_BLK_DEV_SD=y
 CONFIG_CHR_DEV_SG=y
+# CONFIG_BLK_DEV_BSG is not set
 CONFIG_NETDEVICES=y
 CONFIG_BRCMFMAC=m
 CONFIG_INPUT_EVDEV=y
@@ -115,9 +115,9 @@ CONFIG_NLS_ASCII=y
 CONFIG_NLS_ISO8859_1=y
 CONFIG_NLS_UTF8=y
 CONFIG_CRC_CCITT=y
-CONFIG_DEBUG_INFO=y
-CONFIG_MAGIC_SYSRQ=y
 CONFIG_DEBUG_KERNEL=y
+CONFIG_DEBUG_INFO_DWARF_TOOLCHAIN_DEFAULT=y
+CONFIG_MAGIC_SYSRQ=y
 # CONFIG_DEBUG_PREEMPT is not set
 CONFIG_DEBUG_RT_MUTEXES=y
 CONFIG_DEBUG_SPINLOCK=y
diff --git a/arch/arm/configs/sama5_defconfig b/arch/arm/configs/sama5_defconfig
index fe0d7ccc8fb2..877bbe7b777e 100644
--- a/arch/arm/configs/sama5_defconfig
+++ b/arch/arm/configs/sama5_defconfig
@@ -1,5 +1,4 @@
 # CONFIG_LOCALVERSION_AUTO is not set
-# CONFIG_SWAP is not set
 CONFIG_SYSVIPC=y
 CONFIG_NO_HZ_IDLE=y
 CONFIG_HIGH_RES_TIMERS=y
@@ -7,7 +6,6 @@ CONFIG_LOG_BUF_SHIFT=14
 CONFIG_CGROUPS=y
 CONFIG_BLK_DEV_INITRD=y
 CONFIG_EMBEDDED=y
-CONFIG_SLAB=y
 CONFIG_ARCH_AT91=y
 CONFIG_SOC_SAMA5D2=y
 CONFIG_SOC_SAMA5D3=y
@@ -26,8 +24,9 @@ CONFIG_MODULES=y
 CONFIG_MODULE_FORCE_LOAD=y
 CONFIG_MODULE_UNLOAD=y
 CONFIG_MODULE_FORCE_UNLOAD=y
-# CONFIG_BLK_DEV_BSG is not set
 # CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+# CONFIG_SWAP is not set
+CONFIG_SLAB=y
 CONFIG_NET=y
 CONFIG_PACKET=y
 CONFIG_UNIX=y
@@ -44,9 +43,6 @@ CONFIG_BRIDGE_VLAN_FILTERING=y
 CONFIG_NET_DSA=m
 CONFIG_VLAN_8021Q=m
 CONFIG_CAN=y
-CONFIG_CAN_AT91=y
-CONFIG_CAN_M_CAN=y
-CONFIG_CAN_M_CAN_PLATFORM=y
 CONFIG_CFG80211=y
 CONFIG_MAC80211=y
 CONFIG_MAC80211_LEDS=y
@@ -57,13 +53,13 @@ CONFIG_DEVTMPFS_MOUNT=y
 CONFIG_MTD=y
 CONFIG_MTD_TESTS=m
 CONFIG_MTD_CMDLINE_PARTS=y
-CONFIG_MTD_BLOCK=y
 CONFIG_MTD_CFI=y
 CONFIG_MTD_RAW_NAND=y
 CONFIG_MTD_NAND_ATMEL=y
 CONFIG_MTD_SPI_NOR=y
 CONFIG_MTD_UBI=y
 CONFIG_MTD_UBI_FASTMAP=y
+CONFIG_MTD_UBI_BLOCK=y
 CONFIG_BLK_DEV_LOOP=y
 CONFIG_BLK_DEV_RAM=y
 CONFIG_BLK_DEV_RAM_COUNT=4
@@ -72,6 +68,7 @@ CONFIG_ATMEL_SSC=y
 CONFIG_EEPROM_AT24=y
 CONFIG_SCSI=y
 CONFIG_BLK_DEV_SD=y
+# CONFIG_BLK_DEV_BSG is not set
 # CONFIG_SCSI_LOWLEVEL is not set
 CONFIG_NETDEVICES=y
 CONFIG_NET_DSA_MICROCHIP_KSZ9477=m
@@ -90,6 +87,9 @@ CONFIG_MACB=y
 # CONFIG_NET_VENDOR_STMICRO is not set
 # CONFIG_NET_VENDOR_WIZNET is not set
 CONFIG_MICREL_PHY=y
+CONFIG_CAN_AT91=y
+CONFIG_CAN_M_CAN=y
+CONFIG_CAN_M_CAN_PLATFORM=y
 CONFIG_USB_LAN78XX=m
 CONFIG_LIBERTAS_THINFIRM=m
 CONFIG_LIBERTAS_THINFIRM_USB=m
@@ -152,11 +152,11 @@ CONFIG_USB_VIDEO_CLASS=m
 CONFIG_V4L_PLATFORM_DRIVERS=y
 CONFIG_VIDEO_ATMEL_ISC=y
 CONFIG_VIDEO_ATMEL_ISI=y
+CONFIG_VIDEO_MT9V032=m
 CONFIG_VIDEO_OV2640=m
 CONFIG_VIDEO_OV5640=m
 CONFIG_VIDEO_OV7670=m
 CONFIG_VIDEO_OV7740=m
-CONFIG_VIDEO_MT9V032=m
 CONFIG_DRM=y
 CONFIG_DRM_ATMEL_HLCDC=y
 CONFIG_DRM_PANEL_SIMPLE=y
@@ -222,6 +222,7 @@ CONFIG_PWM_ATMEL_HLCDC_PWM=y
 CONFIG_PWM_ATMEL_TCB=y
 CONFIG_EXT4_FS=y
 CONFIG_FANOTIFY=y
+CONFIG_AUTOFS_FS=m
 CONFIG_VFAT_FS=y
 CONFIG_TMPFS=y
 CONFIG_UBIFS_FS=y
@@ -232,6 +233,14 @@ CONFIG_NLS_CODEPAGE_437=y
 CONFIG_NLS_CODEPAGE_850=y
 CONFIG_NLS_ISO8859_1=y
 CONFIG_NLS_UTF8=y
+CONFIG_CRYPTO_CBC=y
+CONFIG_CRYPTO_CFB=y
+CONFIG_CRYPTO_OFB=y
+CONFIG_CRYPTO_XTS=y
+CONFIG_CRYPTO_HMAC=y
+CONFIG_CRYPTO_SHA1=y
+CONFIG_CRYPTO_SHA512=y
+CONFIG_CRYPTO_DES=y
 CONFIG_CRYPTO_USER_API_HASH=m
 CONFIG_CRYPTO_USER_API_SKCIPHER=m
 CONFIG_CRYPTO_DEV_ATMEL_AES=y
diff --git a/arch/arm/configs/sama7_defconfig b/arch/arm/configs/sama7_defconfig
index 938aae4bd80b..8f28c9d443f0 100644
--- a/arch/arm/configs/sama7_defconfig
+++ b/arch/arm/configs/sama7_defconfig
@@ -1,5 +1,4 @@
 # CONFIG_LOCALVERSION_AUTO is not set
-# CONFIG_SWAP is not set
 CONFIG_SYSVIPC=y
 CONFIG_NO_HZ_IDLE=y
 CONFIG_HIGH_RES_TIMERS=y
@@ -14,18 +13,23 @@ CONFIG_BLK_DEV_INITRD=y
 # CONFIG_IO_URING is not set
 CONFIG_KALLSYMS_ALL=y
 CONFIG_EMBEDDED=y
-# CONFIG_VM_EVENT_COUNTERS is not set
-CONFIG_SLAB=y
 CONFIG_ARCH_AT91=y
 CONFIG_SOC_SAMA7G5=y
 CONFIG_ATMEL_CLOCKSOURCE_TCB=y
 # CONFIG_CACHE_L2X0 is not set
 # CONFIG_ARM_PATCH_IDIV is not set
 # CONFIG_CPU_SW_DOMAIN_PAN is not set
-CONFIG_FORCE_MAX_ZONEORDER=15
+CONFIG_ARCH_FORCE_MAX_ORDER=15
 CONFIG_UACCESS_WITH_MEMCPY=y
 # CONFIG_ATAGS is not set
 CONFIG_CMDLINE="console=ttyS0,115200 earlyprintk ignore_loglevel"
+CONFIG_CPU_FREQ=y
+CONFIG_CPU_FREQ_DEFAULT_GOV_CONSERVATIVE=y
+CONFIG_CPU_FREQ_GOV_POWERSAVE=y
+CONFIG_CPU_FREQ_GOV_USERSPACE=y
+CONFIG_CPU_FREQ_GOV_ONDEMAND=y
+CONFIG_CPUFREQ_DT=y
+CONFIG_CPU_IDLE=y
 CONFIG_VFP=y
 CONFIG_NEON=y
 CONFIG_KERNEL_MODE_NEON=y
@@ -33,12 +37,14 @@ CONFIG_MODULES=y
 CONFIG_MODULE_FORCE_LOAD=y
 CONFIG_MODULE_UNLOAD=y
 CONFIG_MODULE_FORCE_UNLOAD=y
-# CONFIG_BLK_DEV_BSG is not set
 CONFIG_PARTITION_ADVANCED=y
 # CONFIG_EFI_PARTITION is not set
 # CONFIG_COREDUMP is not set
+# CONFIG_SWAP is not set
+CONFIG_SLAB=y
 # CONFIG_COMPACTION is not set
 CONFIG_CMA=y
+# CONFIG_VM_EVENT_COUNTERS is not set
 CONFIG_NET=y
 CONFIG_PACKET=y
 CONFIG_UNIX=y
@@ -53,8 +59,6 @@ CONFIG_BRIDGE_VLAN_FILTERING=y
 CONFIG_NET_DSA=m
 CONFIG_VLAN_8021Q=m
 CONFIG_CAN=y
-CONFIG_CAN_M_CAN=y
-CONFIG_CAN_M_CAN_PLATFORM=y
 CONFIG_BT=y
 CONFIG_BT_RFCOMM=y
 CONFIG_BT_RFCOMM_TTY=y
@@ -83,6 +87,13 @@ CONFIG_DEVTMPFS_MOUNT=y
 CONFIG_MTD=y
 CONFIG_MTD_TESTS=m
 CONFIG_MTD_CMDLINE_PARTS=y
+CONFIG_MTD_RAW_NAND=y
+CONFIG_MTD_NAND_ATMEL=y
+# CONFIG_MTD_NAND_ECC_SW_HAMMING is not set
+CONFIG_MTD_SPI_NOR=y
+CONFIG_MTD_UBI=y
+CONFIG_MTD_UBI_FASTMAP=y
+CONFIG_MTD_UBI_BLOCK=y
 CONFIG_BLK_DEV_LOOP=y
 CONFIG_BLK_DEV_RAM=y
 CONFIG_BLK_DEV_RAM_COUNT=1
@@ -90,9 +101,12 @@ CONFIG_BLK_DEV_RAM_SIZE=8192
 CONFIG_EEPROM_AT24=y
 CONFIG_SCSI=y
 CONFIG_BLK_DEV_SD=y
+# CONFIG_BLK_DEV_BSG is not set
 CONFIG_NETDEVICES=y
 CONFIG_MACB=y
 CONFIG_MICREL_PHY=y
+CONFIG_CAN_M_CAN=y
+CONFIG_CAN_M_CAN_PLATFORM=y
 CONFIG_INPUT_EVDEV=y
 CONFIG_KEYBOARD_GPIO=y
 # CONFIG_INPUT_MOUSE is not set
@@ -104,8 +118,8 @@ CONFIG_I2C=y
 CONFIG_I2C_CHARDEV=y
 CONFIG_I2C_AT91=y
 CONFIG_SPI=y
-CONFIG_SPI_MEM=y
 CONFIG_SPI_ATMEL=y
+CONFIG_SPI_ATMEL_QUADSPI=y
 CONFIG_SPI_GPIO=y
 CONFIG_PINCTRL_AT91=y
 CONFIG_PINCTRL_AT91PIO4=y
@@ -126,6 +140,8 @@ CONFIG_MEDIA_SUPPORT_FILTER=y
 CONFIG_MEDIA_CAMERA_SUPPORT=y
 CONFIG_MEDIA_PLATFORM_SUPPORT=y
 CONFIG_V4L_PLATFORM_DRIVERS=y
+CONFIG_VIDEO_ATMEL_XISC=y
+CONFIG_VIDEO_MICROCHIP_CSI2DC=y
 CONFIG_VIDEO_IMX219=m
 CONFIG_VIDEO_IMX274=m
 CONFIG_VIDEO_OV5647=m
@@ -137,6 +153,8 @@ CONFIG_SND_SOC_MIKROE_PROTO=m
 CONFIG_SND_MCHP_SOC_I2S_MCC=y
 CONFIG_SND_MCHP_SOC_SPDIFTX=y
 CONFIG_SND_MCHP_SOC_SPDIFRX=y
+CONFIG_SND_MCHP_SOC_PDMC=y
+CONFIG_SND_SOC_DMIC=y
 CONFIG_SND_SOC_PCM5102A=y
 CONFIG_SND_SOC_SPDIF=y
 CONFIG_SND_SIMPLE_CARD=y
@@ -169,21 +187,22 @@ CONFIG_RTC_DRV_AT91RM9200=y
 CONFIG_RTC_DRV_AT91SAM9=y
 CONFIG_DMADEVICES=y
 CONFIG_AT_XDMAC=y
-CONFIG_DMATEST=y
 CONFIG_STAGING=y
-CONFIG_MICROCHIP_PIT64B=y
 # CONFIG_IOMMU_SUPPORT is not set
-# CONFIG_ATMEL_EBI is not set
 CONFIG_IIO=y
 CONFIG_IIO_SW_TRIGGER=y
 CONFIG_AT91_SAMA5D2_ADC=y
 CONFIG_PWM=y
 CONFIG_PWM_ATMEL=y
+CONFIG_MCHP_EIC=y
+CONFIG_RESET_CONTROLLER=y
 CONFIG_EXT2_FS=y
 CONFIG_EXT3_FS=y
 CONFIG_FANOTIFY=y
+CONFIG_AUTOFS_FS=m
 CONFIG_VFAT_FS=y
 CONFIG_TMPFS=y
+CONFIG_UBIFS_FS=y
 CONFIG_NFS_FS=y
 CONFIG_ROOT_NFS=y
 CONFIG_NLS_CODEPAGE_437=y
@@ -191,17 +210,27 @@ CONFIG_NLS_CODEPAGE_850=y
 CONFIG_NLS_ISO8859_1=y
 CONFIG_NLS_UTF8=y
 CONFIG_LSM="N"
-CONFIG_CRYPTO_DEFLATE=y
-CONFIG_CRYPTO_LZO=y
-# CONFIG_CRYPTO_HW is not set
+CONFIG_CRYPTO_AUTHENC=y
+CONFIG_CRYPTO_GCM=y
+CONFIG_CRYPTO_CBC=y
+CONFIG_CRYPTO_CFB=y
+CONFIG_CRYPTO_OFB=y
+CONFIG_CRYPTO_XTS=y
+CONFIG_CRYPTO_SHA1=y
+CONFIG_CRYPTO_DES=y
+CONFIG_CRYPTO_USER_API_HASH=m
+CONFIG_CRYPTO_USER_API_SKCIPHER=m
+CONFIG_CRYPTO_DEV_ATMEL_AES=y
+CONFIG_CRYPTO_DEV_ATMEL_TDES=y
+CONFIG_CRYPTO_DEV_ATMEL_SHA=y
 CONFIG_CRC_CCITT=y
 CONFIG_CRC_ITU_T=y
 CONFIG_DMA_CMA=y
 CONFIG_CMA_SIZE_MBYTES=32
 CONFIG_CMA_ALIGNMENT=9
+# CONFIG_DEBUG_MISC is not set
 # CONFIG_SECTION_MISMATCH_WARN_ONLY is not set
 CONFIG_DEBUG_FS=y
-# CONFIG_DEBUG_MISC is not set
 # CONFIG_SCHED_DEBUG is not set
 CONFIG_STACKTRACE=y
 # CONFIG_FTRACE is not set
diff --git a/arch/arm/configs/shannon_defconfig b/arch/arm/configs/shannon_defconfig
index de33abdeb6fa..dfcea70b8034 100644
--- a/arch/arm/configs/shannon_defconfig
+++ b/arch/arm/configs/shannon_defconfig
@@ -1,20 +1,22 @@
 CONFIG_SYSVIPC=y
 CONFIG_LOG_BUF_SHIFT=14
 CONFIG_BLK_DEV_INITRD=y
-CONFIG_MODULES=y
+CONFIG_ARCH_MULTI_V4=y
+# CONFIG_ARCH_MULTI_V7 is not set
 CONFIG_ARCH_SA1100=y
 CONFIG_SA1100_SHANNON=y
-CONFIG_PCCARD=y
-CONFIG_PCMCIA_SA1100=y
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_UNUSED_BOARD_FILES=y
 CONFIG_CMDLINE="console=ttySA0,9600 console=tty1 root=/dev/mtdblock2 init=/linuxrc"
 CONFIG_FPE_NWFPE=y
+CONFIG_MODULES=y
+CONFIG_PARTITION_ADVANCED=y
 CONFIG_NET=y
 CONFIG_PACKET=y
 CONFIG_UNIX=y
 CONFIG_INET=y
 # CONFIG_IPV6 is not set
+CONFIG_PCCARD=y
+CONFIG_PCMCIA_SA1100=y
 CONFIG_MTD=y
 CONFIG_MTD_BLOCK=y
 CONFIG_MTD_CFI=y
@@ -40,5 +42,4 @@ CONFIG_VFAT_FS=y
 CONFIG_JFFS2_FS=y
 CONFIG_MINIX_FS=y
 CONFIG_NFS_FS=y
-CONFIG_PARTITION_ADVANCED=y
 CONFIG_DEBUG_USER=y
diff --git a/arch/arm/configs/shmobile_defconfig b/arch/arm/configs/shmobile_defconfig
index 2c2702ec6d02..452aef74cc5c 100644
--- a/arch/arm/configs/shmobile_defconfig
+++ b/arch/arm/configs/shmobile_defconfig
@@ -1,12 +1,11 @@
 CONFIG_SYSVIPC=y
-CONFIG_NO_HZ=y
+CONFIG_NO_HZ_IDLE=y
 CONFIG_IKCONFIG=y
 CONFIG_IKCONFIG_PROC=y
 CONFIG_CGROUPS=y
 CONFIG_BLK_DEV_INITRD=y
 CONFIG_CC_OPTIMIZE_FOR_SIZE=y
 CONFIG_PERF_EVENTS=y
-CONFIG_SLAB=y
 CONFIG_ARCH_RENESAS=y
 CONFIG_PL310_ERRATA_588369=y
 CONFIG_SMP=y
@@ -25,6 +24,7 @@ CONFIG_CPUFREQ_DT=y
 CONFIG_VFP=y
 CONFIG_NEON=y
 # CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+CONFIG_SLAB=y
 CONFIG_CMA=y
 CONFIG_NET=y
 CONFIG_PACKET=y
@@ -32,8 +32,8 @@ CONFIG_UNIX=y
 CONFIG_INET=y
 CONFIG_IP_PNP=y
 CONFIG_IP_PNP_DHCP=y
+CONFIG_NET_DSA=y
 CONFIG_CAN=y
-CONFIG_CAN_RCAR=y
 CONFIG_PCI=y
 CONFIG_PCI_MSI=y
 CONFIG_PCI_RCAR_GEN2=y
@@ -52,11 +52,14 @@ CONFIG_BLK_DEV_SD=y
 CONFIG_ATA=y
 CONFIG_SATA_RCAR=y
 CONFIG_NETDEVICES=y
+CONFIG_NET_DSA_RZN1_A5PSW=y
 CONFIG_SH_ETH=y
 CONFIG_RAVB=y
 CONFIG_SMSC911X=y
+CONFIG_STMMAC_ETH=y
 CONFIG_MICREL_PHY=y
 CONFIG_SMSC_PHY=y
+CONFIG_CAN_RCAR=y
 CONFIG_INPUT_EVDEV=y
 CONFIG_KEYBOARD_GPIO=y
 # CONFIG_INPUT_MOUSE is not set
@@ -69,9 +72,13 @@ CONFIG_INPUT_DA9063_ONKEY=y
 CONFIG_INPUT_ADXL34X=y
 # CONFIG_LEGACY_PTYS is not set
 CONFIG_SERIAL_8250=y
+# CONFIG_SERIAL_8250_DEPRECATED_OPTIONS is not set
+# CONFIG_SERIAL_8250_16550A_VARIANTS is not set
 CONFIG_SERIAL_8250_CONSOLE=y
+# CONFIG_SERIAL_8250_PCI is not set
 CONFIG_SERIAL_8250_DW=y
 CONFIG_SERIAL_8250_EM=y
+# CONFIG_SERIAL_8250_PERICOM is not set
 CONFIG_SERIAL_SH_SCI=y
 CONFIG_I2C_CHARDEV=y
 CONFIG_I2C_DEMUX_PINCTRL=y
@@ -87,6 +94,7 @@ CONFIG_SPI_SH_MSIOF=y
 CONFIG_SPI_SH_HSPI=y
 CONFIG_PINCTRL_RZA1=y
 CONFIG_PINCTRL_RZA2=y
+CONFIG_PINCTRL_RZN1=y
 CONFIG_GPIO_EM=y
 CONFIG_GPIO_RCAR=y
 CONFIG_GPIO_PCA953X=y
@@ -102,6 +110,7 @@ CONFIG_WATCHDOG=y
 CONFIG_DA9063_WATCHDOG=y
 CONFIG_RENESAS_WDT=y
 CONFIG_RENESAS_RZAWDT=y
+CONFIG_RENESAS_RZN1WDT=y
 CONFIG_MFD_AS3711=y
 CONFIG_MFD_DA9063=y
 CONFIG_MFD_STMPE=y
@@ -115,9 +124,9 @@ CONFIG_MEDIA_SUPPORT=y
 CONFIG_MEDIA_CAMERA_SUPPORT=y
 CONFIG_MEDIA_PLATFORM_SUPPORT=y
 CONFIG_V4L_PLATFORM_DRIVERS=y
+CONFIG_V4L_MEM2MEM_DRIVERS=y
 CONFIG_VIDEO_RENESAS_CEU=y
 CONFIG_VIDEO_RCAR_VIN=y
-CONFIG_V4L_MEM2MEM_DRIVERS=y
 CONFIG_VIDEO_RENESAS_FDP1=y
 CONFIG_VIDEO_RENESAS_JPU=y
 CONFIG_VIDEO_RENESAS_VSP1=y
@@ -173,7 +182,10 @@ CONFIG_RTC_DRV_S35390A=y
 CONFIG_RTC_DRV_RX8581=y
 CONFIG_RTC_DRV_DA9063=y
 CONFIG_RTC_DRV_SH=y
+CONFIG_RTC_DRV_RZN1=y
 CONFIG_DMADEVICES=y
+CONFIG_DW_DMAC=y
+CONFIG_RZN1_DMAMUX=y
 CONFIG_RCAR_DMAC=y
 CONFIG_RENESAS_USB_DMAC=y
 CONFIG_STAGING=y
@@ -220,5 +232,5 @@ CONFIG_NLS_ISO8859_1=y
 CONFIG_DMA_CMA=y
 CONFIG_CMA_SIZE_MBYTES=64
 CONFIG_PRINTK_TIME=y
-CONFIG_DEBUG_FS=y
 CONFIG_DEBUG_KERNEL=y
+CONFIG_DEBUG_FS=y
diff --git a/arch/arm/configs/simpad_defconfig b/arch/arm/configs/simpad_defconfig
index 28d99d8895f9..4e00a4c2c287 100644
--- a/arch/arm/configs/simpad_defconfig
+++ b/arch/arm/configs/simpad_defconfig
@@ -1,20 +1,18 @@
 CONFIG_LOCALVERSION="oe1"
 CONFIG_SYSVIPC=y
+CONFIG_PREEMPT=y
 CONFIG_LOG_BUF_SHIFT=14
 CONFIG_EXPERT=y
 CONFIG_KALLSYMS_ALL=y
 CONFIG_KALLSYMS_EXTRA_PASS=y
-CONFIG_MODULES=y
+CONFIG_ARCH_MULTI_V4=y
+# CONFIG_ARCH_MULTI_V7 is not set
 CONFIG_ARCH_SA1100=y
 CONFIG_SA1100_SIMPAD=y
-CONFIG_PCCARD=y
-CONFIG_PCMCIA_SA1100=y
-CONFIG_PREEMPT=y
-CONFIG_LEDS=y
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_UNUSED_BOARD_FILES=y
 CONFIG_CMDLINE="mtdparts=sa1100:512k(boot),1m(kernel),-(root) console=ttySA0 root=1f02 noinitrd mem=64M jffs2_orphaned_inodes=delete rootfstype=jffs2"
 CONFIG_FPE_NWFPE=y
+CONFIG_MODULES=y
 CONFIG_BINFMT_MISC=m
 CONFIG_PM=y
 CONFIG_NET=y
@@ -25,18 +23,14 @@ CONFIG_IP_PNP=y
 CONFIG_IP_PNP_DHCP=y
 CONFIG_IP_PNP_BOOTP=y
 # CONFIG_IPV6 is not set
-CONFIG_IRDA=m
-CONFIG_IRLAN=m
-CONFIG_IRNET=m
-CONFIG_IRCOMM=m
-CONFIG_IRTTY_SIR=m
-CONFIG_SA1100_FIR=m
 CONFIG_BT=m
 CONFIG_BT_RFCOMM=m
 CONFIG_BT_RFCOMM_TTY=y
 CONFIG_BT_BNEP=m
 CONFIG_BT_BNEP_MC_FILTER=y
 CONFIG_BT_BNEP_PROTO_FILTER=y
+CONFIG_PCCARD=y
+CONFIG_PCMCIA_SA1100=y
 CONFIG_MTD=y
 CONFIG_MTD_CMDLINE_PARTS=y
 CONFIG_MTD_BLOCK=y
@@ -56,19 +50,19 @@ CONFIG_DUMMY=y
 CONFIG_NET_ETHERNET=y
 CONFIG_NET_PCI=y
 CONFIG_NET_PCMCIA=y
-CONFIG_PCMCIA_3C589=m
 CONFIG_PCMCIA_3C574=m
+CONFIG_PCMCIA_3C589=m
 CONFIG_PCMCIA_PCNET=m
 CONFIG_PCMCIA_SMC91C92=m
 CONFIG_PCMCIA_XIRC2PS=m
 CONFIG_PPP=m
-CONFIG_PPP_MULTILINK=y
+CONFIG_PPP_BSDCOMP=m
+CONFIG_PPP_DEFLATE=m
 CONFIG_PPP_FILTER=y
+CONFIG_PPP_MULTILINK=y
+CONFIG_PPPOE=m
 CONFIG_PPP_ASYNC=m
 CONFIG_PPP_SYNC_TTY=m
-CONFIG_PPP_DEFLATE=m
-CONFIG_PPP_BSDCOMP=m
-CONFIG_PPPOE=m
 CONFIG_INPUT_MOUSEDEV_SCREEN_X=800
 CONFIG_INPUT_MOUSEDEV_SCREEN_Y=600
 CONFIG_INPUT_EVDEV=m
@@ -83,6 +77,8 @@ CONFIG_FB=y
 CONFIG_FRAMEBUFFER_CONSOLE=y
 CONFIG_LOGO=y
 CONFIG_SOUND=y
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=y
 CONFIG_EXT2_FS=m
 CONFIG_EXT3_FS=m
 CONFIG_REISERFS_FS=m
diff --git a/arch/arm/configs/socfpga_defconfig b/arch/arm/configs/socfpga_defconfig
index 2d9404ea52c6..70739e09d0f4 100644
--- a/arch/arm/configs/socfpga_defconfig
+++ b/arch/arm/configs/socfpga_defconfig
@@ -14,13 +14,10 @@ CONFIG_ARM_THUMBEE=y
 CONFIG_SMP=y
 CONFIG_NR_CPUS=2
 CONFIG_HIGHMEM=y
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
 CONFIG_VFP=y
 CONFIG_NEON=y
 CONFIG_MODULES=y
 CONFIG_MODULE_UNLOAD=y
-# CONFIG_BLK_DEV_BSG is not set
 CONFIG_NET=y
 CONFIG_PACKET=y
 CONFIG_UNIX=y
@@ -36,9 +33,6 @@ CONFIG_NETWORK_PHY_TIMESTAMPING=y
 CONFIG_VLAN_8021Q=y
 CONFIG_VLAN_8021Q_GVRP=y
 CONFIG_CAN=y
-CONFIG_CAN_C_CAN=y
-CONFIG_CAN_C_CAN_PLATFORM=y
-CONFIG_CAN_DEBUG_DEVICES=y
 CONFIG_PCI=y
 CONFIG_PCI_MSI=y
 CONFIG_PCIE_ALTERA=y
@@ -52,7 +46,6 @@ CONFIG_MTD_RAW_NAND=y
 CONFIG_MTD_NAND_DENALI_DT=y
 CONFIG_MTD_SPI_NOR=y
 # CONFIG_MTD_SPI_NOR_USE_4K_SECTORS is not set
-CONFIG_SPI_CADENCE_QUADSPI=y
 CONFIG_OF_OVERLAY=y
 CONFIG_BLK_DEV_LOOP=y
 CONFIG_BLK_DEV_RAM=y
@@ -64,6 +57,7 @@ CONFIG_EEPROM_AT24=y
 CONFIG_SCSI=y
 # CONFIG_SCSI_PROC_FS is not set
 CONFIG_BLK_DEV_SD=y
+# CONFIG_BLK_DEV_BSG is not set
 # CONFIG_SCSI_LOWLEVEL is not set
 CONFIG_NETDEVICES=y
 CONFIG_ALTERA_TSE=m
@@ -73,6 +67,9 @@ CONFIG_IXGBE=m
 CONFIG_STMMAC_ETH=y
 CONFIG_MARVELL_PHY=y
 CONFIG_MICREL_PHY=y
+CONFIG_CAN_C_CAN=y
+CONFIG_CAN_C_CAN_PLATFORM=y
+CONFIG_CAN_DEBUG_DEVICES=y
 CONFIG_INPUT_EVDEV=y
 CONFIG_INPUT_TOUCHSCREEN=y
 CONFIG_TOUCHSCREEN_STMPE=y
@@ -88,6 +85,7 @@ CONFIG_I2C=y
 CONFIG_I2C_CHARDEV=y
 CONFIG_I2C_DESIGNWARE_PLATFORM=y
 CONFIG_SPI=y
+CONFIG_SPI_CADENCE_QUADSPI=y
 CONFIG_SPI_DESIGNWARE=y
 CONFIG_SPI_DW_MMIO=y
 CONFIG_SPI_SPIDEV=y
@@ -154,7 +152,7 @@ CONFIG_NFSD_V4=y
 CONFIG_NLS_CODEPAGE_437=y
 CONFIG_NLS_ISO8859_1=y
 CONFIG_PRINTK_TIME=y
-CONFIG_DEBUG_INFO=y
+CONFIG_DEBUG_INFO_DWARF_TOOLCHAIN_DEFAULT=y
 CONFIG_MAGIC_SYSRQ=y
 CONFIG_DEBUG_FS=y
 CONFIG_DETECT_HUNG_TASK=y
diff --git a/arch/arm/configs/sp7021_defconfig b/arch/arm/configs/sp7021_defconfig
new file mode 100644
index 000000000000..5bca2eb59b86
--- /dev/null
+++ b/arch/arm/configs/sp7021_defconfig
@@ -0,0 +1,59 @@
+CONFIG_SYSVIPC=y
+CONFIG_NO_HZ_IDLE=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_PREEMPT=y
+CONFIG_IKCONFIG=y
+CONFIG_IKCONFIG_PROC=y
+CONFIG_LOG_BUF_SHIFT=14
+# CONFIG_RD_GZIP is not set
+# CONFIG_RD_BZIP2 is not set
+# CONFIG_RD_LZMA is not set
+# CONFIG_RD_XZ is not set
+# CONFIG_RD_LZO is not set
+# CONFIG_RD_LZ4 is not set
+CONFIG_CC_OPTIMIZE_FOR_SIZE=y
+CONFIG_PERF_EVENTS=y
+CONFIG_ARCH_SUNPLUS=y
+# CONFIG_VDSO is not set
+CONFIG_SMP=y
+CONFIG_THUMB2_KERNEL=y
+CONFIG_ARCH_FORCE_MAX_ORDER=12
+CONFIG_VFP=y
+CONFIG_NEON=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_MODVERSIONS=y
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+CONFIG_SLAB=y
+CONFIG_UEVENT_HELPER=y
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_DEVTMPFS=y
+CONFIG_DEVTMPFS_MOUNT=y
+CONFIG_BLK_DEV_LOOP=y
+CONFIG_INPUT_SPARSEKMAP=y
+CONFIG_INPUT_EVDEV=y
+# CONFIG_INPUT_KEYBOARD is not set
+# CONFIG_INPUT_MOUSE is not set
+# CONFIG_LEGACY_PTYS is not set
+# CONFIG_HW_RANDOM is not set
+# CONFIG_HWMON is not set
+# CONFIG_IOMMU_SUPPORT is not set
+CONFIG_RESET_CONTROLLER=y
+CONFIG_EXT4_FS=y
+# CONFIG_DNOTIFY is not set
+CONFIG_FANOTIFY=y
+CONFIG_VFAT_FS=y
+CONFIG_FAT_DEFAULT_IOCHARSET="utf8"
+CONFIG_EXFAT_FS=y
+CONFIG_TMPFS=y
+CONFIG_TMPFS_POSIX_ACL=y
+# CONFIG_MISC_FILESYSTEMS is not set
+CONFIG_NLS_CODEPAGE_437=y
+CONFIG_NLS_ASCII=y
+CONFIG_NLS_ISO8859_1=y
+CONFIG_NLS_UTF8=y
+CONFIG_PRINTK_TIME=y
+CONFIG_DYNAMIC_DEBUG=y
+CONFIG_MAGIC_SYSRQ=y
+CONFIG_DEBUG_FS=y
+CONFIG_DEBUG_USER=y
diff --git a/arch/arm/configs/spear13xx_defconfig b/arch/arm/configs/spear13xx_defconfig
index 3b206a31902f..bfde0c86cdc5 100644
--- a/arch/arm/configs/spear13xx_defconfig
+++ b/arch/arm/configs/spear13xx_defconfig
@@ -1,18 +1,11 @@
 CONFIG_SYSVIPC=y
 CONFIG_BSD_PROCESS_ACCT=y
 CONFIG_BLK_DEV_INITRD=y
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
-CONFIG_MODVERSIONS=y
-CONFIG_PARTITION_ADVANCED=y
 CONFIG_PLAT_SPEAR=y
 CONFIG_ARCH_SPEAR13XX=y
 CONFIG_MACH_SPEAR1310=y
 CONFIG_MACH_SPEAR1340=y
 # CONFIG_SWP_EMULATE is not set
-CONFIG_PCI=y
-CONFIG_PCI_MSI=y
-CONFIG_PCIE_SPEAR13XX=y
 CONFIG_SMP=y
 # CONFIG_SMP_ON_UP is not set
 # CONFIG_ARM_CPU_TOPOLOGY is not set
@@ -20,6 +13,10 @@ CONFIG_AEABI=y
 CONFIG_ARM_APPENDED_DTB=y
 CONFIG_ARM_ATAG_DTB_COMPAT=y
 CONFIG_VFP=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_MODVERSIONS=y
+CONFIG_PARTITION_ADVANCED=y
 CONFIG_BINFMT_MISC=y
 CONFIG_NET=y
 CONFIG_UNIX=y
@@ -28,6 +25,9 @@ CONFIG_IP_PNP=y
 CONFIG_IP_PNP_DHCP=y
 CONFIG_IP_PNP_BOOTP=y
 CONFIG_NET_IPIP=y
+CONFIG_PCI=y
+CONFIG_PCI_MSI=y
+CONFIG_PCIE_SPEAR13XX=y
 CONFIG_MTD=y
 CONFIG_MTD_OF_PARTS=y
 CONFIG_MTD_BLOCK=y
@@ -61,7 +61,6 @@ CONFIG_SERIAL_AMBA_PL011=y
 CONFIG_SERIAL_AMBA_PL011_CONSOLE=y
 # CONFIG_HW_RANDOM is not set
 CONFIG_RAW_DRIVER=y
-CONFIG_MAX_RAW_DEVS=8192
 CONFIG_I2C=y
 CONFIG_I2C_DESIGNWARE_PLATFORM=y
 CONFIG_SPI=y
@@ -98,8 +97,8 @@ CONFIG_ROOT_NFS=y
 CONFIG_NLS_DEFAULT="utf8"
 CONFIG_NLS_CODEPAGE_437=y
 CONFIG_NLS_ASCII=m
+CONFIG_DEBUG_KERNEL=y
+CONFIG_DEBUG_INFO_DWARF_TOOLCHAIN_DEFAULT=y
 CONFIG_MAGIC_SYSRQ=y
 CONFIG_DEBUG_FS=y
-CONFIG_DEBUG_KERNEL=y
 CONFIG_DEBUG_SPINLOCK=y
-CONFIG_DEBUG_INFO=y
diff --git a/arch/arm/configs/spear3xx_defconfig b/arch/arm/configs/spear3xx_defconfig
index fc5f71c765ed..a96ed5cf778e 100644
--- a/arch/arm/configs/spear3xx_defconfig
+++ b/arch/arm/configs/spear3xx_defconfig
@@ -1,16 +1,16 @@
 CONFIG_SYSVIPC=y
 CONFIG_BSD_PROCESS_ACCT=y
 CONFIG_BLK_DEV_INITRD=y
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
-CONFIG_MODVERSIONS=y
-CONFIG_PARTITION_ADVANCED=y
 # CONFIG_ARCH_MULTI_V7 is not set
 CONFIG_PLAT_SPEAR=y
 CONFIG_ARCH_SPEAR3XX=y
 CONFIG_MACH_SPEAR300=y
 CONFIG_MACH_SPEAR310=y
 CONFIG_MACH_SPEAR320=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_MODVERSIONS=y
+CONFIG_PARTITION_ADVANCED=y
 CONFIG_BINFMT_MISC=y
 CONFIG_NET=y
 CONFIG_MTD=y
@@ -41,7 +41,6 @@ CONFIG_SERIAL_AMBA_PL011=y
 CONFIG_SERIAL_AMBA_PL011_CONSOLE=y
 # CONFIG_HW_RANDOM is not set
 CONFIG_RAW_DRIVER=y
-CONFIG_MAX_RAW_DEVS=8192
 CONFIG_I2C=y
 CONFIG_I2C_DESIGNWARE_PLATFORM=y
 CONFIG_SPI=y
@@ -78,8 +77,8 @@ CONFIG_JFFS2_FS=y
 CONFIG_NLS_DEFAULT="utf8"
 CONFIG_NLS_CODEPAGE_437=y
 CONFIG_NLS_ASCII=m
+CONFIG_DEBUG_KERNEL=y
+CONFIG_DEBUG_INFO_DWARF_TOOLCHAIN_DEFAULT=y
 CONFIG_MAGIC_SYSRQ=y
 CONFIG_DEBUG_FS=y
-CONFIG_DEBUG_KERNEL=y
 CONFIG_DEBUG_SPINLOCK=y
-CONFIG_DEBUG_INFO=y
diff --git a/arch/arm/configs/spear6xx_defconfig b/arch/arm/configs/spear6xx_defconfig
index 52a56b8ce6a7..3d631b1f3cfa 100644
--- a/arch/arm/configs/spear6xx_defconfig
+++ b/arch/arm/configs/spear6xx_defconfig
@@ -1,13 +1,13 @@
 CONFIG_SYSVIPC=y
 CONFIG_BSD_PROCESS_ACCT=y
 CONFIG_BLK_DEV_INITRD=y
+# CONFIG_ARCH_MULTI_V7 is not set
+CONFIG_PLAT_SPEAR=y
+CONFIG_ARCH_SPEAR6XX=y
 CONFIG_MODULES=y
 CONFIG_MODULE_UNLOAD=y
 CONFIG_MODVERSIONS=y
 CONFIG_PARTITION_ADVANCED=y
-# CONFIG_ARCH_MULTI_V7 is not set
-CONFIG_PLAT_SPEAR=y
-CONFIG_ARCH_SPEAR6XX=y
 CONFIG_BINFMT_MISC=y
 CONFIG_NET=y
 CONFIG_MTD=y
@@ -36,7 +36,6 @@ CONFIG_INPUT_FF_MEMLESS=y
 CONFIG_SERIAL_AMBA_PL011=y
 CONFIG_SERIAL_AMBA_PL011_CONSOLE=y
 CONFIG_RAW_DRIVER=y
-CONFIG_MAX_RAW_DEVS=8192
 CONFIG_I2C=y
 CONFIG_I2C_DESIGNWARE_PLATFORM=y
 CONFIG_SPI=y
@@ -67,8 +66,8 @@ CONFIG_JFFS2_FS=y
 CONFIG_NLS_DEFAULT="utf8"
 CONFIG_NLS_CODEPAGE_437=y
 CONFIG_NLS_ASCII=m
+CONFIG_DEBUG_KERNEL=y
+CONFIG_DEBUG_INFO_DWARF_TOOLCHAIN_DEFAULT=y
 CONFIG_MAGIC_SYSRQ=y
 CONFIG_DEBUG_FS=y
-CONFIG_DEBUG_KERNEL=y
 CONFIG_DEBUG_SPINLOCK=y
-CONFIG_DEBUG_INFO=y
diff --git a/arch/arm/configs/spitz_defconfig b/arch/arm/configs/spitz_defconfig
index f42c7a502b6e..66d74653f3fb 100644
--- a/arch/arm/configs/spitz_defconfig
+++ b/arch/arm/configs/spitz_defconfig
@@ -1,26 +1,22 @@
 CONFIG_SYSVIPC=y
+CONFIG_PREEMPT=y
 CONFIG_BSD_PROCESS_ACCT=y
 CONFIG_LOG_BUF_SHIFT=14
 CONFIG_SYSFS_DEPRECATED_V2=y
 # CONFIG_CC_OPTIMIZE_FOR_SIZE is not set
 CONFIG_EXPERT=y
 CONFIG_PROFILING=y
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
-CONFIG_MODULE_FORCE_UNLOAD=y
-# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_ARCH_MULTI_V7 is not set
 CONFIG_ARCH_PXA=y
 CONFIG_PXA_SHARPSL=y
 CONFIG_MACH_AKITA=y
 CONFIG_MACH_BORZOI=y
-CONFIG_PCCARD=y
-CONFIG_PCMCIA_PXA2XX=y
-CONFIG_PREEMPT=y
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
 CONFIG_CMDLINE="console=ttyS0,115200n8 console=tty1 noinitrd root=/dev/mtdblock2 rootfstype=jffs2   debug"
 CONFIG_FPE_NWFPE=y
-CONFIG_BINFMT_AOUT=m
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_MODULE_FORCE_UNLOAD=y
+CONFIG_PARTITION_ADVANCED=y
 CONFIG_BINFMT_MISC=m
 CONFIG_PM=y
 CONFIG_NET=y
@@ -54,11 +50,6 @@ CONFIG_IP6_NF_MATCH_RT=m
 CONFIG_IP6_NF_FILTER=m
 CONFIG_IP6_NF_MANGLE=m
 CONFIG_IP6_NF_RAW=m
-CONFIG_IRDA=m
-CONFIG_IRLAN=m
-CONFIG_IRNET=m
-CONFIG_IRCOMM=m
-CONFIG_PXA_FICP=m
 CONFIG_BT=m
 CONFIG_BT_RFCOMM=m
 CONFIG_BT_RFCOMM_TTY=y
@@ -77,6 +68,8 @@ CONFIG_BT_HCIBT3C=m
 CONFIG_BT_HCIBLUECARD=m
 CONFIG_BT_HCIBTUART=m
 CONFIG_BT_HCIVHCI=m
+CONFIG_PCCARD=y
+CONFIG_PCMCIA_PXA2XX=y
 CONFIG_MTD=y
 CONFIG_MTD_CMDLINE_PARTS=y
 CONFIG_MTD_BLOCK=y
@@ -90,10 +83,15 @@ CONFIG_CHR_DEV_ST=m
 CONFIG_CHR_DEV_OSST=m
 CONFIG_BLK_DEV_SR=m
 CONFIG_CHR_DEV_SG=m
+# CONFIG_BLK_DEV_BSG is not set
 CONFIG_ATA=y
 CONFIG_PATA_PCMCIA=y
 CONFIG_NETDEVICES=y
 CONFIG_NET_ETHERNET=y
+CONFIG_PCMCIA_PCNET=m
+CONFIG_PPP=m
+CONFIG_PPP_BSDCOMP=m
+CONFIG_PPP_ASYNC=m
 CONFIG_USB_CATC=m
 CONFIG_USB_KAWETH=m
 CONFIG_USB_PEGASUS=m
@@ -101,10 +99,6 @@ CONFIG_USB_RTL8150=m
 CONFIG_USB_USBNET=m
 # CONFIG_USB_NET_CDC_SUBSET is not set
 CONFIG_NET_PCMCIA=y
-CONFIG_PCMCIA_PCNET=m
-CONFIG_PPP=m
-CONFIG_PPP_ASYNC=m
-CONFIG_PPP_BSDCOMP=m
 CONFIG_INPUT_FF_MEMLESS=m
 # CONFIG_INPUT_MOUSEDEV is not set
 CONFIG_INPUT_EVDEV=y
@@ -115,11 +109,11 @@ CONFIG_TOUCHSCREEN_ADS7846=y
 CONFIG_INPUT_MISC=y
 CONFIG_INPUT_UINPUT=m
 # CONFIG_SERIO is not set
+# CONFIG_LEGACY_PTYS is not set
 CONFIG_SERIAL_8250=m
 CONFIG_SERIAL_8250_CS=m
 CONFIG_SERIAL_PXA=y
 CONFIG_SERIAL_PXA_CONSOLE=y
-# CONFIG_LEGACY_PTYS is not set
 CONFIG_SPI=y
 CONFIG_SPI_PXA2XX=y
 CONFIG_FB=y
@@ -130,11 +124,6 @@ CONFIG_BACKLIGHT_CLASS_DEVICE=y
 # CONFIG_VGA_CONSOLE is not set
 CONFIG_FRAMEBUFFER_CONSOLE=y
 CONFIG_FRAMEBUFFER_CONSOLE_ROTATION=y
-CONFIG_FONTS=y
-CONFIG_FONT_8x8=y
-CONFIG_FONT_8x16=y
-CONFIG_USB_KBD=m
-CONFIG_USB_MOUSE=m
 CONFIG_HID_A4TECH=m
 CONFIG_HID_APPLE=m
 CONFIG_HID_BELKIN=m
@@ -151,6 +140,8 @@ CONFIG_HID_PETALYNX=m
 CONFIG_HID_SAMSUNG=m
 CONFIG_HID_SONY=m
 CONFIG_HID_SUNPLUS=m
+CONFIG_USB_KBD=m
+CONFIG_USB_MOUSE=m
 CONFIG_USB=m
 CONFIG_USB_MON=m
 CONFIG_USB_OHCI_HCD=m
@@ -219,16 +210,12 @@ CONFIG_NFS_V3=y
 CONFIG_NFS_V4=y
 CONFIG_SMB_FS=m
 CONFIG_SMB_NLS_DEFAULT=y
-CONFIG_PARTITION_ADVANCED=y
+CONFIG_NFS_V4=m
 CONFIG_NLS_DEFAULT="cp437"
 CONFIG_NLS_CODEPAGE_437=y
 CONFIG_NLS_ISO8859_1=y
 CONFIG_NLS_UTF8=y
-CONFIG_MAGIC_SYSRQ=y
 CONFIG_DEBUG_KERNEL=y
-# CONFIG_DEBUG_PREEMPT is not set
-# CONFIG_FTRACE is not set
-CONFIG_DEBUG_LL=y
 CONFIG_CRYPTO_NULL=m
 CONFIG_CRYPTO_TEST=m
 CONFIG_CRYPTO_ECB=m
@@ -251,3 +238,9 @@ CONFIG_CRYPTO_TWOFISH=m
 # CONFIG_CRYPTO_ANSI_CPRNG is not set
 CONFIG_CRC_CCITT=y
 CONFIG_LIBCRC32C=m
+CONFIG_FONTS=y
+CONFIG_FONT_8x8=y
+CONFIG_FONT_8x16=y
+CONFIG_MAGIC_SYSRQ=y
+# CONFIG_DEBUG_PREEMPT is not set
+# CONFIG_FTRACE is not set
diff --git a/arch/arm/configs/stm32_defconfig b/arch/arm/configs/stm32_defconfig
index 551db328009d..dc1a32f50b7e 100644
--- a/arch/arm/configs/stm32_defconfig
+++ b/arch/arm/configs/stm32_defconfig
@@ -1,5 +1,6 @@
 CONFIG_NO_HZ_IDLE=y
 CONFIG_HIGH_RES_TIMERS=y
+CONFIG_PREEMPT=y
 CONFIG_LOG_BUF_SHIFT=16
 CONFIG_BLK_DEV_INITRD=y
 CONFIG_CC_OPTIMIZE_FOR_SIZE=y
@@ -11,8 +12,6 @@ CONFIG_CC_OPTIMIZE_FOR_SIZE=y
 # CONFIG_EVENTFD is not set
 # CONFIG_AIO is not set
 CONFIG_EMBEDDED=y
-# CONFIG_VM_EVENT_COUNTERS is not set
-# CONFIG_SLUB_DEBUG is not set
 # CONFIG_BLK_DEV_BSG is not set
 # CONFIG_MMU is not set
 CONFIG_ARCH_STM32=y
@@ -21,15 +20,12 @@ CONFIG_SET_MEM_PARAM=y
 CONFIG_DRAM_BASE=0x90000000
 CONFIG_FLASH_MEM_BASE=0x08000000
 CONFIG_FLASH_SIZE=0x00200000
-CONFIG_PREEMPT=y
 # CONFIG_ATAGS is not set
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
 CONFIG_XIP_KERNEL=y
 CONFIG_XIP_PHYS_ADDR=0x08008000
 CONFIG_BINFMT_FLAT=y
-CONFIG_BINFMT_SHARED_FLAT=y
 # CONFIG_COREDUMP is not set
+# CONFIG_VM_EVENT_COUNTERS is not set
 CONFIG_DEVTMPFS=y
 CONFIG_DEVTMPFS_MOUNT=y
 # CONFIG_FW_LOADER is not set
@@ -39,9 +35,9 @@ CONFIG_KEYBOARD_GPIO=y
 # CONFIG_VT is not set
 # CONFIG_UNIX98_PTYS is not set
 # CONFIG_LEGACY_PTYS is not set
-CONFIG_SERIAL_NONSTANDARD=y
 CONFIG_SERIAL_STM32=y
 CONFIG_SERIAL_STM32_CONSOLE=y
+CONFIG_SERIAL_NONSTANDARD=y
 # CONFIG_HW_RANDOM is not set
 CONFIG_I2C=y
 CONFIG_I2C_CHARDEV=y
@@ -75,12 +71,13 @@ CONFIG_EXT3_FS=y
 # CONFIG_DNOTIFY is not set
 # CONFIG_INOTIFY_USER is not set
 CONFIG_NLS=y
+CONFIG_CRC_ITU_T=y
+CONFIG_CRC7=y
 CONFIG_PRINTK_TIME=y
-CONFIG_DEBUG_INFO=y
 # CONFIG_ENABLE_MUST_CHECK is not set
+# CONFIG_DEBUG_BUGVERBOSE is not set
+CONFIG_DEBUG_INFO_DWARF_TOOLCHAIN_DEFAULT=y
 CONFIG_MAGIC_SYSRQ=y
+# CONFIG_SLUB_DEBUG is not set
 # CONFIG_SCHED_DEBUG is not set
-# CONFIG_DEBUG_BUGVERBOSE is not set
 CONFIG_CRYPTO=y
-CONFIG_CRC_ITU_T=y
-CONFIG_CRC7=y
diff --git a/arch/arm/configs/sunxi_defconfig b/arch/arm/configs/sunxi_defconfig
index 8ba7935bd039..bddc82f78942 100644
--- a/arch/arm/configs/sunxi_defconfig
+++ b/arch/arm/configs/sunxi_defconfig
@@ -1,4 +1,4 @@
-CONFIG_NO_HZ=y
+CONFIG_NO_HZ_IDLE=y
 CONFIG_HIGH_RES_TIMERS=y
 CONFIG_CGROUPS=y
 CONFIG_BLK_DEV_INITRD=y
@@ -26,7 +26,6 @@ CONFIG_IP_PNP_BOOTP=y
 # CONFIG_INET_DIAG is not set
 # CONFIG_IPV6 is not set
 CONFIG_CAN=y
-CONFIG_CAN_SUN4I=y
 # CONFIG_WIRELESS is not set
 CONFIG_DEVTMPFS=y
 CONFIG_DEVTMPFS_MOUNT=y
@@ -52,6 +51,7 @@ CONFIG_STMMAC_ETH=y
 # CONFIG_NET_VENDOR_WIZNET is not set
 CONFIG_MICREL_PHY=y
 CONFIG_REALTEK_PHY=y
+CONFIG_CAN_SUN4I=y
 # CONFIG_WLAN is not set
 CONFIG_INPUT_EVDEV=y
 CONFIG_KEYBOARD_SUN4I_LRADC=y
@@ -97,9 +97,9 @@ CONFIG_IR_SUNXI=y
 CONFIG_MEDIA_SUPPORT=y
 CONFIG_MEDIA_PLATFORM_SUPPORT=y
 CONFIG_V4L_PLATFORM_DRIVERS=y
+CONFIG_V4L_MEM2MEM_DRIVERS=y
 CONFIG_VIDEO_SUN4I_CSI=y
 CONFIG_VIDEO_SUN6I_CSI=y
-CONFIG_V4L_MEM2MEM_DRIVERS=y
 CONFIG_VIDEO_SUN8I_DEINTERLACE=y
 CONFIG_VIDEO_SUN8I_ROTATE=y
 CONFIG_DRM=y
diff --git a/arch/arm/configs/tct_hammer_defconfig b/arch/arm/configs/tct_hammer_defconfig
index 3a9503fe84cb..3b29ae1fb750 100644
--- a/arch/arm/configs/tct_hammer_defconfig
+++ b/arch/arm/configs/tct_hammer_defconfig
@@ -1,24 +1,25 @@
 # CONFIG_LOCALVERSION_AUTO is not set
-# CONFIG_SWAP is not set
 CONFIG_SYSVIPC=y
 CONFIG_LOG_BUF_SHIFT=14
 CONFIG_SYSFS_DEPRECATED=y
 CONFIG_SYSFS_DEPRECATED_V2=y
 CONFIG_BLK_DEV_INITRD=y
 CONFIG_EXPERT=y
-# CONFIG_KALLSYMS is not set
 # CONFIG_ELF_CORE is not set
 # CONFIG_SHMEM is not set
-CONFIG_SLOB=y
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
 # CONFIG_BLK_DEV_BSG is not set
+# CONFIG_KALLSYMS is not set
+CONFIG_ARCH_MULTI_V4T=y
+# CONFIG_ARCH_MULTI_V7 is not set
 CONFIG_ARCH_S3C24XX=y
 CONFIG_MACH_TCT_HAMMER=y
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_UNUSED_BOARD_FILES=y
 CONFIG_CMDLINE="mem=64M root=/dev/ram0 init=/linuxrc rw"
 CONFIG_FPE_NWFPE=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+# CONFIG_SWAP is not set
+CONFIG_SLOB=y
 CONFIG_NET=y
 CONFIG_PACKET=y
 CONFIG_UNIX=y
@@ -53,5 +54,5 @@ CONFIG_JFFS2_FS=y
 CONFIG_NLS_CODEPAGE_437=y
 CONFIG_NLS_ISO8859_1=y
 # CONFIG_ENABLE_MUST_CHECK is not set
-CONFIG_DEBUG_LL=y
 CONFIG_CRC_CCITT=y
+CONFIG_DEBUG_LL=y
diff --git a/arch/arm/configs/tegra_defconfig b/arch/arm/configs/tegra_defconfig
index 8a8f12b3e6dd..f32047e24b63 100644
--- a/arch/arm/configs/tegra_defconfig
+++ b/arch/arm/configs/tegra_defconfig
@@ -1,5 +1,5 @@
 CONFIG_SYSVIPC=y
-CONFIG_NO_HZ=y
+CONFIG_NO_HZ_IDLE=y
 CONFIG_HIGH_RES_TIMERS=y
 CONFIG_PREEMPT=y
 CONFIG_IKCONFIG=y
@@ -16,7 +16,6 @@ CONFIG_BLK_DEV_INITRD=y
 # CONFIG_ELF_CORE is not set
 CONFIG_EMBEDDED=y
 CONFIG_PERF_EVENTS=y
-CONFIG_SLAB=y
 CONFIG_ARCH_TEGRA=y
 CONFIG_SMP=y
 CONFIG_HIGHMEM=y
@@ -29,12 +28,11 @@ CONFIG_CPU_IDLE=y
 CONFIG_ARM_TEGRA_CPUIDLE=y
 CONFIG_VFP=y
 CONFIG_NEON=y
-CONFIG_TRUSTED_FOUNDATIONS=y
 CONFIG_MODULES=y
 CONFIG_MODULE_UNLOAD=y
 CONFIG_MODULE_FORCE_UNLOAD=y
-# CONFIG_BLK_DEV_BSG is not set
 CONFIG_PARTITION_ADVANCED=y
+CONFIG_SLAB=y
 CONFIG_CMA=y
 CONFIG_NET=y
 CONFIG_PACKET=y
@@ -56,7 +54,6 @@ CONFIG_IPV6_MIP6=y
 CONFIG_IPV6_TUNNEL=y
 CONFIG_IPV6_MULTIPLE_TABLES=y
 CONFIG_CAN=y
-CONFIG_CAN_MCP251X=y
 CONFIG_BT=y
 CONFIG_BT_RFCOMM=y
 CONFIG_BT_BNEP=y
@@ -80,6 +77,7 @@ CONFIG_PCI_TEGRA=y
 CONFIG_DEVTMPFS=y
 CONFIG_DEVTMPFS_MOUNT=y
 CONFIG_TEGRA_GMI=y
+CONFIG_TRUSTED_FOUNDATIONS=y
 CONFIG_MTD=y
 CONFIG_MTD_SPI_NOR=y
 CONFIG_BLK_DEV_LOOP=y
@@ -91,6 +89,7 @@ CONFIG_ISL29003=y
 CONFIG_EEPROM_AT24=y
 CONFIG_BLK_DEV_SD=y
 CONFIG_BLK_DEV_SR=y
+# CONFIG_BLK_DEV_BSG is not set
 # CONFIG_SCSI_LOWLEVEL is not set
 CONFIG_ATA=y
 CONFIG_SATA_AHCI=y
@@ -99,11 +98,14 @@ CONFIG_NETDEVICES=y
 CONFIG_DUMMY=y
 CONFIG_IGB=y
 CONFIG_R8169=y
+CONFIG_CAN_MCP251X=y
 CONFIG_USB_PEGASUS=y
 CONFIG_USB_USBNET=y
 CONFIG_USB_NET_SMSC75XX=y
 CONFIG_USB_NET_SMSC95XX=y
 CONFIG_BRCMFMAC=m
+CONFIG_MWIFIEX=m
+CONFIG_MWIFIEX_SDIO=m
 CONFIG_RT2X00=y
 CONFIG_RT2800USB=m
 CONFIG_INPUT_JOYDEV=y
@@ -113,6 +115,8 @@ CONFIG_KEYBOARD_TEGRA=y
 CONFIG_KEYBOARD_CROS_EC=y
 CONFIG_KEYBOARD_CAP11XX=y
 CONFIG_MOUSE_PS2_ELANTECH=y
+CONFIG_MOUSE_ELAN_I2C=m
+CONFIG_MOUSE_ELAN_I2C_SMBUS=y
 CONFIG_INPUT_TOUCHSCREEN=y
 CONFIG_TOUCHSCREEN_ATMEL_MXT=y
 CONFIG_TOUCHSCREEN_ELAN=y
@@ -131,9 +135,11 @@ CONFIG_SERIAL_DEV_BUS=y
 # CONFIG_HW_RANDOM is not set
 # CONFIG_I2C_COMPAT is not set
 CONFIG_I2C_CHARDEV=y
+CONFIG_I2C_MUX_GPIO=y
 CONFIG_I2C_MUX_PCA954x=y
 CONFIG_I2C_MUX_PINCTRL=y
 CONFIG_I2C_TEGRA=y
+CONFIG_I2C_CROS_EC_TUNNEL=m
 CONFIG_SPI=y
 CONFIG_SPI_TEGRA114=y
 CONFIG_SPI_TEGRA20_SFLASH=y
@@ -151,9 +157,11 @@ CONFIG_GPIO_TPS65910=y
 CONFIG_POWER_RESET=y
 CONFIG_POWER_RESET_AS3722=y
 CONFIG_POWER_RESET_GPIO=y
+CONFIG_POWER_RESET_GPIO_RESTART=y
 CONFIG_BATTERY_SBS=y
 CONFIG_BATTERY_BQ27XXX=y
 CONFIG_CHARGER_GPIO=y
+CONFIG_CHARGER_BQ24735=y
 CONFIG_CHARGER_SMB347=y
 CONFIG_CHARGER_TPS65090=y
 CONFIG_BATTERY_ACER_A500=y
@@ -191,8 +199,10 @@ CONFIG_REGULATOR_TPS6586X=y
 CONFIG_REGULATOR_TPS65910=y
 CONFIG_MEDIA_SUPPORT=y
 CONFIG_MEDIA_USB_SUPPORT=y
-CONFIG_USB_VIDEO_CLASS=y
 CONFIG_USB_GSPCA=y
+CONFIG_USB_VIDEO_CLASS=y
+CONFIG_V4L_MEM2MEM_DRIVERS=y
+CONFIG_VIDEO_TEGRA_VDE=y
 CONFIG_DRM=y
 CONFIG_DRM_NOUVEAU=m
 CONFIG_DRM_TEGRA=y
@@ -200,7 +210,9 @@ CONFIG_DRM_TEGRA_STAGING=y
 CONFIG_DRM_PANEL_LVDS=y
 CONFIG_DRM_PANEL_SIMPLE=y
 CONFIG_DRM_PANEL_EDP=y
+CONFIG_DRM_PANEL_SHARP_LQ101R1SX01=y
 CONFIG_DRM_LVDS_CODEC=y
+CONFIG_DRM_TOSHIBA_TC358768=y
 CONFIG_FB=y
 CONFIG_BACKLIGHT_CLASS_DEVICE=y
 CONFIG_BACKLIGHT_PWM=y
@@ -222,6 +234,7 @@ CONFIG_SND_HDA_CODEC_HDMI=y
 CONFIG_SND_SOC=y
 CONFIG_SND_SOC_TEGRA=y
 CONFIG_SND_SOC_TEGRA20_I2S=y
+CONFIG_SND_SOC_TEGRA20_SPDIF=y
 CONFIG_SND_SOC_TEGRA30_I2S=y
 CONFIG_SND_SOC_TEGRA_RT5640=y
 CONFIG_SND_SOC_TEGRA_WM8753=y
@@ -276,9 +289,10 @@ CONFIG_SERIO_NVEC_PS2=y
 CONFIG_NVEC_POWER=y
 CONFIG_NVEC_PAZ00=y
 CONFIG_STAGING_MEDIA=y
-CONFIG_TEGRA_VDE=y
 CONFIG_CHROME_PLATFORMS=y
 CONFIG_CROS_EC=y
+CONFIG_CROS_EC_I2C=m
+CONFIG_CROS_EC_SPI=m
 CONFIG_TEGRA_IOMMU_GART=y
 CONFIG_TEGRA_IOMMU_SMMU=y
 CONFIG_ARCH_TEGRA_2x_SOC=y
@@ -329,7 +343,7 @@ CONFIG_CRYPTO_TWOFISH=y
 CONFIG_DMA_CMA=y
 CONFIG_CMA_SIZE_MBYTES=64
 CONFIG_PRINTK_TIME=y
-CONFIG_DEBUG_INFO=y
+CONFIG_DEBUG_INFO_DWARF_TOOLCHAIN_DEFAULT=y
 CONFIG_MAGIC_SYSRQ=y
 CONFIG_DEBUG_SLAB=y
 CONFIG_DEBUG_VM=y
diff --git a/arch/arm/configs/trizeps4_defconfig b/arch/arm/configs/trizeps4_defconfig
index d66f0c287d41..009abe1e49ef 100644
--- a/arch/arm/configs/trizeps4_defconfig
+++ b/arch/arm/configs/trizeps4_defconfig
@@ -1,5 +1,6 @@
 CONFIG_SYSVIPC=y
 CONFIG_POSIX_MQUEUE=y
+CONFIG_PREEMPT=y
 CONFIG_BSD_PROCESS_ACCT=y
 CONFIG_BSD_PROCESS_ACCT_V3=y
 CONFIG_IKCONFIG=y
@@ -8,24 +9,24 @@ CONFIG_LOG_BUF_SHIFT=14
 CONFIG_BLK_DEV_INITRD=y
 CONFIG_EXPERT=y
 CONFIG_KALLSYMS_EXTRA_PASS=y
-CONFIG_SLAB=y
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
-CONFIG_MODULE_FORCE_UNLOAD=y
-CONFIG_MODVERSIONS=y
-CONFIG_MODULE_SRCVERSION_ALL=y
+# CONFIG_ARCH_MULTI_V7 is not set
 CONFIG_ARCH_PXA=y
 CONFIG_TRIZEPS_PXA=y
 CONFIG_MACH_TRIZEPS4=y
-CONFIG_PCCARD=y
-# CONFIG_PCMCIA_LOAD_CIS is not set
-CONFIG_PCMCIA_PXA2XX=y
-CONFIG_PREEMPT=y
 CONFIG_AEABI=y
+CONFIG_UNUSED_BOARD_FILES=y
 CONFIG_CMDLINE="root=fe01 console=ttyS0,38400n8 loglevel=5"
 CONFIG_FPE_NWFPE=y
 CONFIG_FPE_NWFPE_XP=y
 CONFIG_PM=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_MODULE_FORCE_UNLOAD=y
+CONFIG_MODVERSIONS=y
+CONFIG_MODULE_SRCVERSION_ALL=y
+CONFIG_PARTITION_ADVANCED=y
+CONFIG_LDM_PARTITION=y
+CONFIG_SLAB=y
 CONFIG_NET=y
 CONFIG_PACKET=y
 CONFIG_UNIX=y
@@ -38,14 +39,6 @@ CONFIG_IP_PNP_BOOTP=y
 # CONFIG_IPV6 is not set
 CONFIG_NETFILTER=y
 CONFIG_VLAN_8021Q=m
-CONFIG_IRDA=m
-CONFIG_IRLAN=m
-CONFIG_IRNET=m
-CONFIG_IRCOMM=m
-CONFIG_IRDA_ULTRA=y
-CONFIG_IRDA_CACHE_LAST_LSAP=y
-CONFIG_IRDA_FAST_RR=y
-CONFIG_IRTTY_SIR=m
 CONFIG_BT=m
 CONFIG_BT_RFCOMM=m
 CONFIG_BT_RFCOMM_TTY=y
@@ -54,6 +47,9 @@ CONFIG_BT_BNEP_MC_FILTER=y
 CONFIG_BT_BNEP_PROTO_FILTER=y
 CONFIG_BT_HIDP=m
 CONFIG_CFG80211=y
+CONFIG_PCCARD=y
+# CONFIG_PCMCIA_LOAD_CIS is not set
+CONFIG_PCMCIA_PXA2XX=y
 CONFIG_CONNECTOR=y
 CONFIG_MTD=y
 CONFIG_MTD_REDBOOT_PARTS=y
@@ -76,13 +72,13 @@ CONFIG_MTD_DOC2001PLUS=y
 CONFIG_MTD_DOCPROBE_ADVANCED=y
 CONFIG_MTD_DOCPROBE_ADDRESS=0x4000000
 CONFIG_MTD_DOCPROBE_HIGH=y
+CONFIG_MTD_ONENAND=y
 CONFIG_MTD_RAW_NAND=y
 CONFIG_MTD_NAND_DISKONCHIP=y
 CONFIG_MTD_NAND_DISKONCHIP_PROBE_ADVANCED=y
 CONFIG_MTD_NAND_DISKONCHIP_PROBE_ADDRESS=0x4000000
 CONFIG_MTD_NAND_DISKONCHIP_PROBE_HIGH=y
 CONFIG_MTD_NAND_DISKONCHIP_BBTWRITE=y
-CONFIG_MTD_ONENAND=y
 CONFIG_BLK_DEV_LOOP=y
 CONFIG_BLK_DEV_CRYPTOLOOP=m
 CONFIG_BLK_DEV_NBD=y
@@ -96,9 +92,17 @@ CONFIG_ATA=m
 CONFIG_PATA_PCMCIA=m
 CONFIG_PATA_PLATFORM=m
 CONFIG_NETDEVICES=y
-CONFIG_PHYLIB=y
 CONFIG_NET_ETHERNET=y
 CONFIG_DM9000=y
+CONFIG_PHYLIB=y
+CONFIG_PPP=m
+CONFIG_PPP_BSDCOMP=m
+CONFIG_PPP_DEFLATE=m
+CONFIG_PPP_FILTER=y
+CONFIG_PPP_MPPE=m
+CONFIG_PPP_MULTILINK=y
+CONFIG_PPP_ASYNC=m
+CONFIG_PPP_SYNC_TTY=m
 CONFIG_HOSTAP=y
 CONFIG_HOSTAP_FIRMWARE=y
 CONFIG_HOSTAP_FIRMWARE_NVRAM=y
@@ -106,14 +110,6 @@ CONFIG_HOSTAP_CS=y
 CONFIG_HERMES=y
 CONFIG_PCMCIA_HERMES=y
 CONFIG_PCMCIA_SPECTRUM=y
-CONFIG_PPP=m
-CONFIG_PPP_MULTILINK=y
-CONFIG_PPP_FILTER=y
-CONFIG_PPP_ASYNC=m
-CONFIG_PPP_SYNC_TTY=m
-CONFIG_PPP_DEFLATE=m
-CONFIG_PPP_BSDCOMP=m
-CONFIG_PPP_MPPE=m
 CONFIG_INPUT_MOUSEDEV_SCREEN_X=640
 CONFIG_INPUT_MOUSEDEV_SCREEN_Y=480
 CONFIG_INPUT_EVDEV=y
@@ -141,17 +137,14 @@ CONFIG_BACKLIGHT_CLASS_DEVICE=y
 # CONFIG_VGA_CONSOLE is not set
 CONFIG_FRAMEBUFFER_CONSOLE=y
 CONFIG_FRAMEBUFFER_CONSOLE_ROTATION=y
-CONFIG_FONTS=y
-CONFIG_FONT_8x8=y
-CONFIG_FONT_8x16=y
 CONFIG_LOGO=y
 CONFIG_SOUND=y
 CONFIG_SND=y
-CONFIG_SND_SEQUENCER=y
 CONFIG_SND_MIXER_OSS=y
 CONFIG_SND_PCM_OSS=y
 CONFIG_SND_VERBOSE_PRINTK=y
 CONFIG_SND_DEBUG=y
+CONFIG_SND_SEQUENCER=y
 CONFIG_SND_PXA2XX_AC97=y
 CONFIG_SND_USB_AUDIO=m
 # CONFIG_USB_HID is not set
@@ -190,8 +183,6 @@ CONFIG_NFSD=y
 CONFIG_NFSD_V4=y
 CONFIG_SMB_FS=m
 CONFIG_CIFS=m
-CONFIG_PARTITION_ADVANCED=y
-CONFIG_LDM_PARTITION=y
 CONFIG_NLS_DEFAULT="iso8859-15"
 CONFIG_NLS_CODEPAGE_437=y
 CONFIG_NLS_CODEPAGE_850=y
@@ -199,9 +190,6 @@ CONFIG_NLS_ASCII=y
 CONFIG_NLS_ISO8859_1=m
 CONFIG_NLS_ISO8859_15=m
 CONFIG_NLS_UTF8=m
-CONFIG_MAGIC_SYSRQ=y
-CONFIG_DEBUG_FS=y
-CONFIG_DEBUG_USER=y
 CONFIG_KEYS=y
 CONFIG_SECURITY=y
 CONFIG_CRYPTO_PCBC=m
@@ -211,3 +199,9 @@ CONFIG_CRYPTO_DEFLATE=m
 CONFIG_CRC_CCITT=y
 CONFIG_CRC16=y
 CONFIG_LIBCRC32C=y
+CONFIG_FONTS=y
+CONFIG_FONT_8x8=y
+CONFIG_FONT_8x16=y
+CONFIG_MAGIC_SYSRQ=y
+CONFIG_DEBUG_FS=y
+CONFIG_DEBUG_USER=y
diff --git a/arch/arm/configs/u8500_defconfig b/arch/arm/configs/u8500_defconfig
index 3b30913d7d8d..3bdc217667a6 100644
--- a/arch/arm/configs/u8500_defconfig
+++ b/arch/arm/configs/u8500_defconfig
@@ -1,4 +1,3 @@
-# CONFIG_SWAP is not set
 CONFIG_SYSVIPC=y
 CONFIG_NO_HZ_IDLE=y
 CONFIG_HIGH_RES_TIMERS=y
@@ -20,8 +19,8 @@ CONFIG_VFP=y
 CONFIG_NEON=y
 CONFIG_MODULES=y
 CONFIG_MODULE_UNLOAD=y
-# CONFIG_BLK_DEV_BSG is not set
 CONFIG_PARTITION_ADVANCED=y
+# CONFIG_SWAP is not set
 CONFIG_CMA=y
 CONFIG_NET=y
 CONFIG_PACKET=y
@@ -41,6 +40,8 @@ CONFIG_MAC80211_LEDS=y
 CONFIG_CAIF=y
 CONFIG_DEVTMPFS=y
 CONFIG_DEVTMPFS_MOUNT=y
+CONFIG_GNSS=y
+CONFIG_GNSS_SIRF_SERIAL=y
 CONFIG_BLK_DEV_RAM=y
 CONFIG_BLK_DEV_RAM_SIZE=65536
 CONFIG_NETDEVICES=y
@@ -83,6 +84,8 @@ CONFIG_SPI_GPIO=y
 CONFIG_SPI_PL022=y
 CONFIG_GPIO_STMPE=y
 CONFIG_GPIO_TC3589X=y
+CONFIG_BATTERY_SAMSUNG_SDI=y
+CONFIG_AB8500_BM=y
 CONFIG_SENSORS_IIO_HWMON=y
 CONFIG_SENSORS_NTC_THERMISTOR=y
 CONFIG_THERMAL=y
@@ -98,10 +101,13 @@ CONFIG_VIDEO_V4L2_SUBDEV_API=y
 CONFIG_V4L2_FLASH_LED_CLASS=y
 CONFIG_DRM=y
 CONFIG_DRM_PANEL_NOVATEK_NT35510=y
+CONFIG_DRM_PANEL_NOVATEK_NT35560=y
+CONFIG_DRM_PANEL_SAMSUNG_DB7430=y
 CONFIG_DRM_PANEL_SAMSUNG_S6D16D0=y
+CONFIG_DRM_PANEL_SAMSUNG_S6D27A1=y
 CONFIG_DRM_PANEL_SAMSUNG_S6E63M0=y
 CONFIG_DRM_PANEL_SAMSUNG_S6E63M0_DSI=y
-CONFIG_DRM_PANEL_SONY_ACX424AKP=y
+CONFIG_DRM_PANEL_WIDECHIPS_WS2401=y
 CONFIG_DRM_LIMA=y
 CONFIG_DRM_MCDE=y
 CONFIG_FB=y
@@ -129,6 +135,7 @@ CONFIG_LEDS_LM3530=y
 CONFIG_LEDS_GPIO=y
 CONFIG_LEDS_LP55XX_COMMON=y
 CONFIG_LEDS_LP5521=y
+CONFIG_LEDS_REGULATOR=y
 CONFIG_LEDS_RT8515=y
 CONFIG_LEDS_TRIGGER_HEARTBEAT=y
 CONFIG_RTC_CLASS=y
@@ -144,17 +151,22 @@ CONFIG_IIO_SW_TRIGGER=y
 CONFIG_BMA180=y
 CONFIG_BMC150_ACCEL=y
 CONFIG_IIO_ST_ACCEL_3AXIS=y
+# CONFIG_IIO_ST_ACCEL_SPI_3AXIS is not set
 CONFIG_IIO_RESCALE=y
 CONFIG_MPU3050_I2C=y
 CONFIG_IIO_ST_GYRO_3AXIS=y
+# CONFIG_IIO_ST_GYRO_SPI_3AXIS is not set
 CONFIG_INV_MPU6050_I2C=y
 CONFIG_BH1780=y
 CONFIG_GP2AP002=y
+CONFIG_TSL2772=y
 CONFIG_AK8974=y
 CONFIG_IIO_ST_MAGN_3AXIS=y
+# CONFIG_IIO_ST_MAGN_SPI_3AXIS is not set
 CONFIG_YAMAHA_YAS530=y
 CONFIG_IIO_HRTIMER_TRIGGER=y
 CONFIG_IIO_ST_PRESS=y
+# CONFIG_IIO_ST_PRESS_SPI is not set
 CONFIG_EXT2_FS=y
 CONFIG_EXT2_FS_XATTR=y
 CONFIG_EXT2_FS_POSIX_ACL=y
@@ -173,10 +185,9 @@ CONFIG_CRYPTO_DEV_UX500_CRYP=y
 CONFIG_CRYPTO_DEV_UX500_HASH=y
 CONFIG_CRYPTO_DEV_UX500_DEBUG=y
 CONFIG_PRINTK_TIME=y
-CONFIG_DEBUG_INFO=y
+CONFIG_DEBUG_KERNEL=y
 CONFIG_MAGIC_SYSRQ=y
 CONFIG_DEBUG_FS=y
-CONFIG_DEBUG_KERNEL=y
 # CONFIG_SCHED_DEBUG is not set
 # CONFIG_FTRACE is not set
 CONFIG_DEBUG_USER=y
diff --git a/arch/arm/configs/versatile_defconfig b/arch/arm/configs/versatile_defconfig
index d06aa64e05a1..67e3f9138306 100644
--- a/arch/arm/configs/versatile_defconfig
+++ b/arch/arm/configs/versatile_defconfig
@@ -4,7 +4,6 @@ CONFIG_NO_HZ_IDLE=y
 CONFIG_HIGH_RES_TIMERS=y
 CONFIG_LOG_BUF_SHIFT=14
 CONFIG_BLK_DEV_INITRD=y
-CONFIG_SLAB=y
 # CONFIG_ARCH_MULTI_V7 is not set
 CONFIG_ARCH_VERSATILE=y
 CONFIG_AEABI=y
@@ -15,6 +14,7 @@ CONFIG_VFP=y
 CONFIG_MODULES=y
 CONFIG_MODULE_UNLOAD=y
 CONFIG_PARTITION_ADVANCED=y
+CONFIG_SLAB=y
 CONFIG_CMA=y
 CONFIG_NET=y
 CONFIG_PACKET=y
@@ -86,11 +86,10 @@ CONFIG_ROMFS_FS=y
 CONFIG_NFS_FS=y
 CONFIG_ROOT_NFS=y
 CONFIG_NFSD=y
-CONFIG_NFSD_V3=y
 CONFIG_NLS_CODEPAGE_850=m
 CONFIG_NLS_ISO8859_1=m
+CONFIG_DEBUG_KERNEL=y
 CONFIG_MAGIC_SYSRQ=y
 CONFIG_DEBUG_FS=y
-CONFIG_DEBUG_KERNEL=y
 CONFIG_DEBUG_USER=y
 CONFIG_DEBUG_LL=y
diff --git a/arch/arm/configs/vexpress_defconfig b/arch/arm/configs/vexpress_defconfig
index 947987730eb7..ac3fd7523698 100644
--- a/arch/arm/configs/vexpress_defconfig
+++ b/arch/arm/configs/vexpress_defconfig
@@ -20,15 +20,12 @@ CONFIG_MCPM=y
 CONFIG_VMSPLIT_2G=y
 CONFIG_NR_CPUS=8
 CONFIG_ARM_PSCI=y
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
 CONFIG_CMDLINE="console=ttyAMA0"
 CONFIG_CPU_IDLE=y
 CONFIG_VFP=y
 CONFIG_NEON=y
 CONFIG_MODULES=y
 CONFIG_MODULE_UNLOAD=y
-# CONFIG_BLK_DEV_BSG is not set
 # CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
 CONFIG_CMA=y
 CONFIG_NET=y
@@ -56,6 +53,7 @@ CONFIG_MTD_UBI=y
 CONFIG_VIRTIO_BLK=y
 # CONFIG_SCSI_PROC_FS is not set
 CONFIG_BLK_DEV_SD=y
+# CONFIG_BLK_DEV_BSG is not set
 CONFIG_SCSI_VIRTIO=y
 CONFIG_ATA=y
 CONFIG_NETDEVICES=y
@@ -135,9 +133,9 @@ CONFIG_NLS_CODEPAGE_437=y
 CONFIG_NLS_ISO8859_1=y
 # CONFIG_CRYPTO_HW is not set
 CONFIG_DMA_CMA=y
-CONFIG_DEBUG_INFO=y
-CONFIG_MAGIC_SYSRQ=y
 CONFIG_DEBUG_KERNEL=y
+CONFIG_DEBUG_INFO_DWARF_TOOLCHAIN_DEFAULT=y
+CONFIG_MAGIC_SYSRQ=y
 CONFIG_DETECT_HUNG_TASK=y
 # CONFIG_SCHED_DEBUG is not set
 CONFIG_DEBUG_USER=y
diff --git a/arch/arm/configs/vf610m4_defconfig b/arch/arm/configs/vf610m4_defconfig
index a89f035c3b01..2e47cc57a928 100644
--- a/arch/arm/configs/vf610m4_defconfig
+++ b/arch/arm/configs/vf610m4_defconfig
@@ -16,10 +16,9 @@ CONFIG_FLASH_SIZE=0x01000000
 CONFIG_CMDLINE="console=/dev/ttyLP2"
 CONFIG_XIP_KERNEL=y
 CONFIG_XIP_PHYS_ADDR=0x0f000080
+# CONFIG_SUSPEND is not set
 CONFIG_BINFMT_FLAT=y
 CONFIG_BINFMT_ZFLAT=y
-CONFIG_BINFMT_SHARED_FLAT=y
-# CONFIG_SUSPEND is not set
 # CONFIG_UEVENT_HELPER is not set
 # CONFIG_STANDALONE is not set
 # CONFIG_PREVENT_FIRMWARE_BUILD is not set
diff --git a/arch/arm/configs/viper_defconfig b/arch/arm/configs/viper_defconfig
index 989599ce5300..02f9849893b2 100644
--- a/arch/arm/configs/viper_defconfig
+++ b/arch/arm/configs/viper_defconfig
@@ -1,22 +1,15 @@
-# CONFIG_SWAP is not set
 CONFIG_SYSVIPC=y
 CONFIG_LOG_BUF_SHIFT=13
 CONFIG_SYSFS_DEPRECATED_V2=y
 CONFIG_EXPERT=y
 # CONFIG_ELF_CORE is not set
 # CONFIG_SHMEM is not set
-CONFIG_SLAB=y
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
-# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_ARCH_MULTI_V7 is not set
 CONFIG_ARCH_PXA=y
 CONFIG_ARCH_VIPER=y
 CONFIG_IWMMXT=y
-CONFIG_PCCARD=m
-CONFIG_PCMCIA_PXA2XX=m
 CONFIG_AEABI=y
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_UNUSED_BOARD_FILES=y
 CONFIG_CMDLINE="root=31:02 rootfstype=jffs2 ro console=ttyS0,115200"
 CONFIG_CPU_FREQ=y
 CONFIG_CPU_FREQ_GOV_POWERSAVE=m
@@ -25,6 +18,11 @@ CONFIG_CPU_FREQ_GOV_ONDEMAND=m
 CONFIG_CPU_FREQ_GOV_CONSERVATIVE=m
 CONFIG_FPE_FASTFPE=y
 CONFIG_PM=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_PARTITION_ADVANCED=y
+# CONFIG_SWAP is not set
+CONFIG_SLAB=y
 CONFIG_NET=y
 CONFIG_PACKET=y
 CONFIG_UNIX=y
@@ -40,6 +38,8 @@ CONFIG_BT_BNEP=m
 CONFIG_BT_HCIUART=m
 CONFIG_BT_HCIUART_H4=y
 CONFIG_BT_HCIUART_BCSP=y
+CONFIG_PCCARD=m
+CONFIG_PCMCIA_PXA2XX=m
 CONFIG_FW_LOADER=m
 CONFIG_MTD=y
 CONFIG_MTD_REDBOOT_PARTS=y
@@ -60,20 +60,21 @@ CONFIG_MTD_PXA2XX=y
 CONFIG_BLK_DEV_LOOP=m
 # CONFIG_SCSI_PROC_FS is not set
 CONFIG_BLK_DEV_SD=m
+# CONFIG_BLK_DEV_BSG is not set
 CONFIG_ATA=m
 # CONFIG_SATA_PMP is not set
 CONFIG_PATA_PCMCIA=m
 CONFIG_NETDEVICES=y
 CONFIG_NET_ETHERNET=y
 CONFIG_SMC91X=y
+CONFIG_PPP=m
+CONFIG_PPP_BSDCOMP=m
+CONFIG_PPP_DEFLATE=m
+CONFIG_PPP_ASYNC=m
 CONFIG_USB_PEGASUS=m
 CONFIG_USB_USBNET=m
 # CONFIG_USB_NET_CDC_SUBSET is not set
 CONFIG_NET_PCMCIA=y
-CONFIG_PPP=m
-CONFIG_PPP_ASYNC=m
-CONFIG_PPP_DEFLATE=m
-CONFIG_PPP_BSDCOMP=m
 CONFIG_INPUT_MOUSEDEV=m
 # CONFIG_INPUT_MOUSEDEV_PSAUX is not set
 CONFIG_INPUT_EVDEV=m
@@ -93,12 +94,12 @@ CONFIG_INPUT_MISC=y
 CONFIG_INPUT_UINPUT=m
 # CONFIG_CONSOLE_TRANSLATIONS is not set
 # CONFIG_VT_CONSOLE is not set
+# CONFIG_LEGACY_PTYS is not set
 CONFIG_SERIAL_8250=m
 CONFIG_SERIAL_8250_NR_UARTS=5
 CONFIG_SERIAL_8250_RUNTIME_UARTS=5
 CONFIG_SERIAL_PXA=y
 CONFIG_SERIAL_PXA_CONSOLE=y
-# CONFIG_LEGACY_PTYS is not set
 CONFIG_I2C=y
 CONFIG_I2C_CHARDEV=y
 # CONFIG_I2C_HELPER_AUTO is not set
@@ -145,17 +146,15 @@ CONFIG_NFS_FS=y
 CONFIG_NFS_V3=y
 CONFIG_ROOT_NFS=y
 CONFIG_NFSD=m
-CONFIG_NFSD_V3=y
-CONFIG_PARTITION_ADVANCED=y
 CONFIG_NLS_CODEPAGE_437=m
 CONFIG_NLS_CODEPAGE_850=m
 CONFIG_NLS_ISO8859_1=m
 CONFIG_NLS_ISO8859_15=m
 CONFIG_NLS_UTF8=m
+CONFIG_CRC_T10DIF=m
 CONFIG_MAGIC_SYSRQ=y
 CONFIG_DEBUG_KERNEL=y
 CONFIG_DEBUG_MUTEXES=y
 # CONFIG_FTRACE is not set
 CONFIG_CRYPTO_ECB=m
 CONFIG_CRYPTO_ARC4=m
-CONFIG_CRC_T10DIF=m
diff --git a/arch/arm/configs/vt8500_v6_v7_defconfig b/arch/arm/configs/vt8500_v6_v7_defconfig
index 9b85326ba287..41607a84abc8 100644
--- a/arch/arm/configs/vt8500_v6_v7_defconfig
+++ b/arch/arm/configs/vt8500_v6_v7_defconfig
@@ -1,4 +1,4 @@
-CONFIG_NO_HZ=y
+CONFIG_NO_HZ_IDLE=y
 CONFIG_HIGH_RES_TIMERS=y
 CONFIG_BLK_DEV_INITRD=y
 CONFIG_ARCH_MULTI_V6=y
@@ -50,8 +50,8 @@ CONFIG_I2C_WMT=y
 CONFIG_PINCTRL_SINGLE=y
 CONFIG_PINCTRL_WM8750=y
 CONFIG_GPIO_GENERIC_PLATFORM=y
-CONFIG_POWER_SUPPLY=y
 CONFIG_POWER_RESET=y
+CONFIG_POWER_SUPPLY=y
 CONFIG_MFD_SYSCON=y
 CONFIG_REGULATOR=y
 CONFIG_REGULATOR_FIXED_VOLTAGE=y
diff --git a/arch/arm/configs/xcep_defconfig b/arch/arm/configs/xcep_defconfig
index 4d8e7f2eaef7..ea59e4b6bfc5 100644
--- a/arch/arm/configs/xcep_defconfig
+++ b/arch/arm/configs/xcep_defconfig
@@ -1,6 +1,8 @@
 CONFIG_LOCALVERSION=".xcep-itech"
 # CONFIG_LOCALVERSION_AUTO is not set
 CONFIG_SYSVIPC=y
+CONFIG_NO_HZ_IDLE=y
+CONFIG_HIGH_RES_TIMERS=y
 CONFIG_BSD_PROCESS_ACCT=y
 CONFIG_IKCONFIG=y
 CONFIG_IKCONFIG_PROC=y
@@ -10,25 +12,23 @@ CONFIG_BLK_DEV_INITRD=y
 CONFIG_EXPERT=y
 # CONFIG_UID16 is not set
 # CONFIG_SHMEM is not set
-# CONFIG_VM_EVENT_COUNTERS is not set
-# CONFIG_COMPAT_BRK is not set
-CONFIG_SLOB=y
-CONFIG_KPROBES=y
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
-CONFIG_MODVERSIONS=y
-CONFIG_MODULE_SRCVERSION_ALL=y
-# CONFIG_BLOCK is not set
+# CONFIG_ARCH_MULTI_V7 is not set
 CONFIG_ARCH_PXA=y
 CONFIG_MACH_XCEP=y
 CONFIG_IWMMXT=y
-CONFIG_NO_HZ=y
-CONFIG_HIGH_RES_TIMERS=y
 CONFIG_AEABI=y
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_UNUSED_BOARD_FILES=y
 CONFIG_CMDLINE="root=mtd4 rootfstype=jffs2 ro console=ttyS0,115200"
 CONFIG_FPE_NWFPE=y
+CONFIG_KPROBES=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_MODVERSIONS=y
+CONFIG_MODULE_SRCVERSION_ALL=y
+# CONFIG_BLOCK is not set
+CONFIG_SLOB=y
+# CONFIG_COMPAT_BRK is not set
+# CONFIG_VM_EVENT_COUNTERS is not set
 CONFIG_NET=y
 CONFIG_PACKET=m
 CONFIG_UNIX=y
@@ -53,9 +53,9 @@ CONFIG_NET_ETHERNET=y
 # CONFIG_INPUT_KEYBOARD is not set
 # CONFIG_INPUT_MOUSE is not set
 # CONFIG_SERIO is not set
+# CONFIG_LEGACY_PTYS is not set
 CONFIG_SERIAL_PXA=y
 CONFIG_SERIAL_PXA_CONSOLE=y
-# CONFIG_LEGACY_PTYS is not set
 # CONFIG_HW_RANDOM is not set
 CONFIG_I2C=m
 CONFIG_I2C_CHARDEV=m
@@ -77,13 +77,13 @@ CONFIG_NFS_V3=y
 CONFIG_NLS=m
 CONFIG_NLS_DEFAULT="utf8"
 CONFIG_NLS_UTF8=m
+# CONFIG_CRYPTO_HW is not set
+CONFIG_LIBCRC32C=m
 CONFIG_PRINTK_TIME=y
+# CONFIG_DEBUG_BUGVERBOSE is not set
 CONFIG_STRIP_ASM_SYMS=y
 CONFIG_DEBUG_KERNEL=y
 # CONFIG_SCHED_DEBUG is not set
-# CONFIG_DEBUG_BUGVERBOSE is not set
 # CONFIG_FTRACE is not set
 # CONFIG_ARM_UNWIND is not set
 # CONFIG_CRYPTO_ANSI_CPRNG is not set
-# CONFIG_CRYPTO_HW is not set
-CONFIG_LIBCRC32C=m
diff --git a/arch/arm/configs/zeus_defconfig b/arch/arm/configs/zeus_defconfig
index d3b98c4d225b..c4535315e216 100644
--- a/arch/arm/configs/zeus_defconfig
+++ b/arch/arm/configs/zeus_defconfig
@@ -1,16 +1,11 @@
 CONFIG_SYSVIPC=y
 CONFIG_TINY_RCU=y
 CONFIG_LOG_BUF_SHIFT=13
-CONFIG_MODULES=y
-CONFIG_MODULE_UNLOAD=y
-# CONFIG_BLK_DEV_BSG is not set
+# CONFIG_ARCH_MULTI_V7 is not set
 CONFIG_ARCH_PXA=y
 CONFIG_MACH_ARCOM_ZEUS=y
-CONFIG_PCCARD=m
-CONFIG_PCMCIA_PXA2XX=m
 CONFIG_AEABI=y
-CONFIG_ZBOOT_ROM_TEXT=0x0
-CONFIG_ZBOOT_ROM_BSS=0x0
+CONFIG_UNUSED_BOARD_FILES=y
 CONFIG_CMDLINE="root=31:02 rootfstype=jffs2 ro console=ttyS0,115200"
 CONFIG_CPU_FREQ=y
 CONFIG_CPU_FREQ_GOV_POWERSAVE=m
@@ -20,6 +15,9 @@ CONFIG_CPU_FREQ_GOV_CONSERVATIVE=m
 CONFIG_FPE_NWFPE=y
 CONFIG_PM=y
 CONFIG_APM_EMULATION=y
+CONFIG_MODULES=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_PARTITION_ADVANCED=y
 CONFIG_NET=y
 CONFIG_PACKET=y
 CONFIG_UNIX=y
@@ -38,6 +36,8 @@ CONFIG_BT_HCIUART_BCSP=y
 CONFIG_CFG80211=m
 CONFIG_LIB80211=m
 CONFIG_MAC80211=m
+CONFIG_PCCARD=m
+CONFIG_PCMCIA_PXA2XX=m
 CONFIG_MTD=y
 CONFIG_MTD_REDBOOT_PARTS=y
 CONFIG_MTD_REDBOOT_PARTS_READONLY=y
@@ -58,21 +58,22 @@ CONFIG_BLK_DEV_LOOP=m
 CONFIG_EEPROM_AT24=m
 # CONFIG_SCSI_PROC_FS is not set
 CONFIG_BLK_DEV_SD=m
+# CONFIG_BLK_DEV_BSG is not set
 CONFIG_ATA=m
 # CONFIG_SATA_PMP is not set
 CONFIG_PATA_PCMCIA=m
 CONFIG_NETDEVICES=y
 CONFIG_NET_ETHERNET=y
 CONFIG_DM9000=y
+CONFIG_PPP=m
+CONFIG_PPP_BSDCOMP=m
+CONFIG_PPP_DEFLATE=m
+CONFIG_PPP_ASYNC=m
 CONFIG_HERMES=m
 CONFIG_PCMCIA_HERMES=m
 CONFIG_RT2X00=m
 CONFIG_RT73USB=m
 CONFIG_NET_PCMCIA=y
-CONFIG_PPP=m
-CONFIG_PPP_ASYNC=m
-CONFIG_PPP_DEFLATE=m
-CONFIG_PPP_BSDCOMP=m
 # CONFIG_INPUT_MOUSEDEV_PSAUX is not set
 CONFIG_INPUT_EVDEV=m
 # CONFIG_INPUT_KEYBOARD is not set
@@ -89,11 +90,11 @@ CONFIG_TOUCHSCREEN_TOUCHWIN=m
 CONFIG_TOUCHSCREEN_TOUCHIT213=m
 CONFIG_INPUT_MISC=y
 CONFIG_INPUT_UINPUT=m
+# CONFIG_LEGACY_PTYS is not set
 CONFIG_SERIAL_8250=y
 CONFIG_SERIAL_8250_CONSOLE=y
 CONFIG_SERIAL_8250_NR_UARTS=7
 CONFIG_SERIAL_8250_RUNTIME_UARTS=7
-# CONFIG_LEGACY_PTYS is not set
 CONFIG_I2C=y
 CONFIG_I2C_CHARDEV=y
 # CONFIG_I2C_HELPER_AUTO is not set
@@ -160,15 +161,13 @@ CONFIG_NFS_FS=y
 CONFIG_NFS_V3=y
 CONFIG_ROOT_NFS=y
 CONFIG_NFSD=m
-CONFIG_NFSD_V3=y
-CONFIG_PARTITION_ADVANCED=y
 CONFIG_NLS_CODEPAGE_437=m
 CONFIG_NLS_CODEPAGE_850=m
 CONFIG_NLS_ISO8859_1=m
 CONFIG_NLS_ISO8859_15=m
 CONFIG_NLS_UTF8=m
-CONFIG_MAGIC_SYSRQ=y
+CONFIG_CRC_T10DIF=m
 CONFIG_DEBUG_KERNEL=y
+CONFIG_MAGIC_SYSRQ=y
 CONFIG_DEBUG_MUTEXES=y
 # CONFIG_CRYPTO_ANSI_CPRNG is not set
-CONFIG_CRC_T10DIF=m
diff --git a/arch/arm/crypto/Kconfig b/arch/arm/crypto/Kconfig
index 2b575792363e..3858c4d4cb98 100644
--- a/arch/arm/crypto/Kconfig
+++ b/arch/arm/crypto/Kconfig
@@ -1,92 +1,156 @@
 # SPDX-License-Identifier: GPL-2.0
 
-menuconfig ARM_CRYPTO
-	bool "ARM Accelerated Cryptographic Algorithms"
-	depends on ARM
+menu "Accelerated Cryptographic Algorithms for CPU (arm)"
+
+config CRYPTO_CURVE25519_NEON
+	tristate "Public key crypto: Curve25519 (NEON)"
+	depends on KERNEL_MODE_NEON
+	select CRYPTO_LIB_CURVE25519_GENERIC
+	select CRYPTO_ARCH_HAVE_LIB_CURVE25519
+	help
+	  Curve25519 algorithm
+
+	  Architecture: arm with
+	  - NEON (Advanced SIMD) extensions
+
+config CRYPTO_GHASH_ARM_CE
+	tristate "Hash functions: GHASH (PMULL/NEON/ARMv8 Crypto Extensions)"
+	depends on KERNEL_MODE_NEON
+	select CRYPTO_HASH
+	select CRYPTO_CRYPTD
+	select CRYPTO_GF128MUL
 	help
-	  Say Y here to choose from a selection of cryptographic algorithms
-	  implemented using ARM specific CPU features or instructions.
+	  GCM GHASH function (NIST SP800-38D)
 
-if ARM_CRYPTO
+	  Architecture: arm using
+	  - PMULL (Polynomial Multiply Long) instructions
+	  - NEON (Advanced SIMD) extensions
+	  - ARMv8 Crypto Extensions
+
+	  Use an implementation of GHASH (used by the GCM AEAD chaining mode)
+	  that uses the 64x64 to 128 bit polynomial multiplication (vmull.p64)
+	  that is part of the ARMv8 Crypto Extensions, or a slower variant that
+	  uses the vmull.p8 instruction that is part of the basic NEON ISA.
+
+config CRYPTO_NHPOLY1305_NEON
+	tristate "Hash functions: NHPoly1305 (NEON)"
+	depends on KERNEL_MODE_NEON
+	select CRYPTO_NHPOLY1305
+	help
+	  NHPoly1305 hash function (Adiantum)
+
+	  Architecture: arm using:
+	  - NEON (Advanced SIMD) extensions
+
+config CRYPTO_POLY1305_ARM
+	tristate "Hash functions: Poly1305 (NEON)"
+	select CRYPTO_HASH
+	select CRYPTO_ARCH_HAVE_LIB_POLY1305
+	help
+	  Poly1305 authenticator algorithm (RFC7539)
+
+	  Architecture: arm optionally using
+	  - NEON (Advanced SIMD) extensions
+
+config CRYPTO_BLAKE2S_ARM
+	bool "Hash functions: BLAKE2s"
+	select CRYPTO_ARCH_HAVE_LIB_BLAKE2S
+	help
+	  BLAKE2s cryptographic hash function (RFC 7693)
+
+	  Architecture: arm
+
+	  This is faster than the generic implementations of BLAKE2s and
+	  BLAKE2b, but slower than the NEON implementation of BLAKE2b.
+	  There is no NEON implementation of BLAKE2s, since NEON doesn't
+	  really help with it.
+
+config CRYPTO_BLAKE2B_NEON
+	tristate "Hash functions: BLAKE2b (NEON)"
+	depends on KERNEL_MODE_NEON
+	select CRYPTO_BLAKE2B
+	help
+	  BLAKE2b cryptographic hash function (RFC 7693)
+
+	  Architecture: arm using
+	  - NEON (Advanced SIMD) extensions
+
+	  BLAKE2b digest algorithm optimized with ARM NEON instructions.
+	  On ARM processors that have NEON support but not the ARMv8
+	  Crypto Extensions, typically this BLAKE2b implementation is
+	  much faster than the SHA-2 family and slightly faster than
+	  SHA-1.
 
 config CRYPTO_SHA1_ARM
-	tristate "SHA1 digest algorithm (ARM-asm)"
+	tristate "Hash functions: SHA-1"
 	select CRYPTO_SHA1
 	select CRYPTO_HASH
 	help
-	  SHA-1 secure hash standard (FIPS 180-1/DFIPS 180-2) implemented
-	  using optimized ARM assembler.
+	  SHA-1 secure hash algorithm (FIPS 180)
+
+	  Architecture: arm
 
 config CRYPTO_SHA1_ARM_NEON
-	tristate "SHA1 digest algorithm (ARM NEON)"
+	tristate "Hash functions: SHA-1 (NEON)"
 	depends on KERNEL_MODE_NEON
 	select CRYPTO_SHA1_ARM
 	select CRYPTO_SHA1
 	select CRYPTO_HASH
 	help
-	  SHA-1 secure hash standard (FIPS 180-1/DFIPS 180-2) implemented
-	  using optimized ARM NEON assembly, when NEON instructions are
-	  available.
+	  SHA-1 secure hash algorithm (FIPS 180)
+
+	  Architecture: arm using
+	  - NEON (Advanced SIMD) extensions
 
 config CRYPTO_SHA1_ARM_CE
-	tristate "SHA1 digest algorithm (ARM v8 Crypto Extensions)"
+	tristate "Hash functions: SHA-1 (ARMv8 Crypto Extensions)"
 	depends on KERNEL_MODE_NEON
 	select CRYPTO_SHA1_ARM
 	select CRYPTO_HASH
 	help
-	  SHA-1 secure hash standard (FIPS 180-1/DFIPS 180-2) implemented
-	  using special ARMv8 Crypto Extensions.
+	  SHA-1 secure hash algorithm (FIPS 180)
+
+	  Architecture: arm using ARMv8 Crypto Extensions
 
 config CRYPTO_SHA2_ARM_CE
-	tristate "SHA-224/256 digest algorithm (ARM v8 Crypto Extensions)"
+	tristate "Hash functions: SHA-224 and SHA-256 (ARMv8 Crypto Extensions)"
 	depends on KERNEL_MODE_NEON
 	select CRYPTO_SHA256_ARM
 	select CRYPTO_HASH
 	help
-	  SHA-256 secure hash standard (DFIPS 180-2) implemented
-	  using special ARMv8 Crypto Extensions.
+	  SHA-224 and SHA-256 secure hash algorithms (FIPS 180)
+
+	  Architecture: arm using
+	  - ARMv8 Crypto Extensions
 
 config CRYPTO_SHA256_ARM
-	tristate "SHA-224/256 digest algorithm (ARM-asm and NEON)"
+	tristate "Hash functions: SHA-224 and SHA-256 (NEON)"
 	select CRYPTO_HASH
 	depends on !CPU_V7M
 	help
-	  SHA-256 secure hash standard (DFIPS 180-2) implemented
-	  using optimized ARM assembler and NEON, when available.
+	  SHA-224 and SHA-256 secure hash algorithms (FIPS 180)
+
+	  Architecture: arm using
+	  - NEON (Advanced SIMD) extensions
 
 config CRYPTO_SHA512_ARM
-	tristate "SHA-384/512 digest algorithm (ARM-asm and NEON)"
+	tristate "Hash functions: SHA-384 and SHA-512 (NEON)"
 	select CRYPTO_HASH
 	depends on !CPU_V7M
 	help
-	  SHA-512 secure hash standard (DFIPS 180-2) implemented
-	  using optimized ARM assembler and NEON, when available.
+	  SHA-384 and SHA-512 secure hash algorithms (FIPS 180)
 
-config CRYPTO_BLAKE2S_ARM
-	tristate "BLAKE2s digest algorithm (ARM)"
-	select CRYPTO_ARCH_HAVE_LIB_BLAKE2S
-	help
-	  BLAKE2s digest algorithm optimized with ARM scalar instructions.  This
-	  is faster than the generic implementations of BLAKE2s and BLAKE2b, but
-	  slower than the NEON implementation of BLAKE2b.  (There is no NEON
-	  implementation of BLAKE2s, since NEON doesn't really help with it.)
-
-config CRYPTO_BLAKE2B_NEON
-	tristate "BLAKE2b digest algorithm (ARM NEON)"
-	depends on KERNEL_MODE_NEON
-	select CRYPTO_BLAKE2B
-	help
-	  BLAKE2b digest algorithm optimized with ARM NEON instructions.
-	  On ARM processors that have NEON support but not the ARMv8
-	  Crypto Extensions, typically this BLAKE2b implementation is
-	  much faster than SHA-2 and slightly faster than SHA-1.
+	  Architecture: arm using
+	  - NEON (Advanced SIMD) extensions
 
 config CRYPTO_AES_ARM
-	tristate "Scalar AES cipher for ARM"
+	tristate "Ciphers: AES"
 	select CRYPTO_ALGAPI
 	select CRYPTO_AES
 	help
-	  Use optimized AES assembler routines for ARM platforms.
+	  Block ciphers: AES cipher algorithms (FIPS-197)
+
+	  Architecture: arm
 
 	  On ARM processors without the Crypto Extensions, this is the
 	  fastest AES implementation for single blocks.  For multiple
@@ -98,14 +162,21 @@ config CRYPTO_AES_ARM
 	  such attacks very difficult.
 
 config CRYPTO_AES_ARM_BS
-	tristate "Bit sliced AES using NEON instructions"
+	tristate "Ciphers: AES, modes: ECB/CBC/CTR/XTS (bit-sliced NEON)"
 	depends on KERNEL_MODE_NEON
 	select CRYPTO_SKCIPHER
 	select CRYPTO_LIB_AES
+	select CRYPTO_AES
+	select CRYPTO_CBC
 	select CRYPTO_SIMD
 	help
-	  Use a faster and more secure NEON based implementation of AES in CBC,
-	  CTR and XTS modes
+	  Length-preserving ciphers: AES cipher algorithms (FIPS-197)
+	  with block cipher modes:
+	   - ECB (Electronic Codebook) mode (NIST SP800-38A)
+	   - CBC (Cipher Block Chaining) mode (NIST SP800-38A)
+	   - CTR (Counter) mode (NIST SP800-38A)
+	   - XTS (XOR Encrypt XOR with ciphertext stealing) mode (NIST SP800-38E
+	     and IEEE 1619)
 
 	  Bit sliced AES gives around 45% speedup on Cortex-A15 for CTR mode
 	  and for XTS mode encryption, CBC and XTS mode decryption speedup is
@@ -114,58 +185,59 @@ config CRYPTO_AES_ARM_BS
 	  believed to be invulnerable to cache timing attacks.
 
 config CRYPTO_AES_ARM_CE
-	tristate "Accelerated AES using ARMv8 Crypto Extensions"
+	tristate "Ciphers: AES, modes: ECB/CBC/CTS/CTR/XTS (ARMv8 Crypto Extensions)"
 	depends on KERNEL_MODE_NEON
 	select CRYPTO_SKCIPHER
 	select CRYPTO_LIB_AES
 	select CRYPTO_SIMD
 	help
-	  Use an implementation of AES in CBC, CTR and XTS modes that uses
-	  ARMv8 Crypto Extensions
+	  Length-preserving ciphers: AES cipher algorithms (FIPS-197)
+	   with block cipher modes:
+	   - ECB (Electronic Codebook) mode (NIST SP800-38A)
+	   - CBC (Cipher Block Chaining) mode (NIST SP800-38A)
+	   - CTR (Counter) mode (NIST SP800-38A)
+	   - CTS (Cipher Text Stealing) mode (NIST SP800-38A)
+	   - XTS (XOR Encrypt XOR with ciphertext stealing) mode (NIST SP800-38E
+	     and IEEE 1619)
+
+	  Architecture: arm using:
+	  - ARMv8 Crypto Extensions
 
-config CRYPTO_GHASH_ARM_CE
-	tristate "PMULL-accelerated GHASH using NEON/ARMv8 Crypto Extensions"
-	depends on KERNEL_MODE_NEON
-	select CRYPTO_HASH
-	select CRYPTO_CRYPTD
-	select CRYPTO_GF128MUL
+config CRYPTO_CHACHA20_NEON
+	tristate "Ciphers: ChaCha20, XChaCha20, XChaCha12 (NEON)"
+	select CRYPTO_SKCIPHER
+	select CRYPTO_ARCH_HAVE_LIB_CHACHA
 	help
-	  Use an implementation of GHASH (used by the GCM AEAD chaining mode)
-	  that uses the 64x64 to 128 bit polynomial multiplication (vmull.p64)
-	  that is part of the ARMv8 Crypto Extensions, or a slower variant that
-	  uses the vmull.p8 instruction that is part of the basic NEON ISA.
+	  Length-preserving ciphers: ChaCha20, XChaCha20, and XChaCha12
+	  stream cipher algorithms
 
-config CRYPTO_CRCT10DIF_ARM_CE
-	tristate "CRCT10DIF digest algorithm using PMULL instructions"
-	depends on KERNEL_MODE_NEON
-	depends on CRC_T10DIF
-	select CRYPTO_HASH
+	  Architecture: arm using:
+	  - NEON (Advanced SIMD) extensions
 
 config CRYPTO_CRC32_ARM_CE
-	tristate "CRC32(C) digest algorithm using CRC and/or PMULL instructions"
+	tristate "CRC32C and CRC32"
 	depends on KERNEL_MODE_NEON
 	depends on CRC32
 	select CRYPTO_HASH
+	help
+	  CRC32c CRC algorithm with the iSCSI polynomial (RFC 3385 and RFC 3720)
+	  and CRC32 CRC algorithm (IEEE 802.3)
 
-config CRYPTO_CHACHA20_NEON
-	tristate "NEON and scalar accelerated ChaCha stream cipher algorithms"
-	select CRYPTO_SKCIPHER
-	select CRYPTO_ARCH_HAVE_LIB_CHACHA
+	  Architecture: arm using:
+	  - CRC and/or PMULL instructions
 
-config CRYPTO_POLY1305_ARM
-	tristate "Accelerated scalar and SIMD Poly1305 hash implementations"
-	select CRYPTO_HASH
-	select CRYPTO_ARCH_HAVE_LIB_POLY1305
+	  Drivers: crc32-arm-ce and crc32c-arm-ce
 
-config CRYPTO_NHPOLY1305_NEON
-	tristate "NEON accelerated NHPoly1305 hash function (for Adiantum)"
+config CRYPTO_CRCT10DIF_ARM_CE
+	tristate "CRCT10DIF"
 	depends on KERNEL_MODE_NEON
-	select CRYPTO_NHPOLY1305
+	depends on CRC_T10DIF
+	select CRYPTO_HASH
+	help
+	  CRC16 CRC algorithm used for the T10 (SCSI) Data Integrity Field (DIF)
 
-config CRYPTO_CURVE25519_NEON
-	tristate "NEON accelerated Curve25519 scalar multiplication library"
-	depends on KERNEL_MODE_NEON
-	select CRYPTO_LIB_CURVE25519_GENERIC
-	select CRYPTO_ARCH_HAVE_LIB_CURVE25519
+	  Architecture: arm using:
+	  - PMULL (Polynomial Multiply Long) instructions
+
+endmenu
 
-endif
diff --git a/arch/arm/crypto/Makefile b/arch/arm/crypto/Makefile
index eafa898ba6a7..971e74546fb1 100644
--- a/arch/arm/crypto/Makefile
+++ b/arch/arm/crypto/Makefile
@@ -9,7 +9,7 @@ obj-$(CONFIG_CRYPTO_SHA1_ARM) += sha1-arm.o
 obj-$(CONFIG_CRYPTO_SHA1_ARM_NEON) += sha1-arm-neon.o
 obj-$(CONFIG_CRYPTO_SHA256_ARM) += sha256-arm.o
 obj-$(CONFIG_CRYPTO_SHA512_ARM) += sha512-arm.o
-obj-$(CONFIG_CRYPTO_BLAKE2S_ARM) += blake2s-arm.o
+obj-$(CONFIG_CRYPTO_BLAKE2S_ARM) += libblake2s-arm.o
 obj-$(CONFIG_CRYPTO_BLAKE2B_NEON) += blake2b-neon.o
 obj-$(CONFIG_CRYPTO_CHACHA20_NEON) += chacha-neon.o
 obj-$(CONFIG_CRYPTO_POLY1305_ARM) += poly1305-arm.o
@@ -31,7 +31,7 @@ sha256-arm-neon-$(CONFIG_KERNEL_MODE_NEON) := sha256_neon_glue.o
 sha256-arm-y	:= sha256-core.o sha256_glue.o $(sha256-arm-neon-y)
 sha512-arm-neon-$(CONFIG_KERNEL_MODE_NEON) := sha512-neon-glue.o
 sha512-arm-y	:= sha512-core.o sha512-glue.o $(sha512-arm-neon-y)
-blake2s-arm-y   := blake2s-core.o blake2s-glue.o
+libblake2s-arm-y:= blake2s-core.o blake2s-glue.o
 blake2b-neon-y  := blake2b-neon-core.o blake2b-neon-glue.o
 sha1-arm-ce-y	:= sha1-ce-core.o sha1-ce-glue.o
 sha2-arm-ce-y	:= sha2-ce-core.o sha2-ce-glue.o
diff --git a/arch/arm/crypto/aes-neonbs-core.S b/arch/arm/crypto/aes-neonbs-core.S
index 7d0cc7f226a5..7b61032f29fa 100644
--- a/arch/arm/crypto/aes-neonbs-core.S
+++ b/arch/arm/crypto/aes-neonbs-core.S
@@ -758,29 +758,24 @@ ENTRY(aesbs_cbc_decrypt)
 ENDPROC(aesbs_cbc_decrypt)
 
 	.macro		next_ctr, q
-	vmov.32		\q\()h[1], r10
+	vmov		\q\()h, r9, r10
 	adds		r10, r10, #1
-	vmov.32		\q\()h[0], r9
 	adcs		r9, r9, #0
-	vmov.32		\q\()l[1], r8
+	vmov		\q\()l, r7, r8
 	adcs		r8, r8, #0
-	vmov.32		\q\()l[0], r7
 	adc		r7, r7, #0
 	vrev32.8	\q, \q
 	.endm
 
 	/*
 	 * aesbs_ctr_encrypt(u8 out[], u8 const in[], u8 const rk[],
-	 *		     int rounds, int blocks, u8 ctr[], u8 final[])
+	 *		     int rounds, int bytes, u8 ctr[])
 	 */
 ENTRY(aesbs_ctr_encrypt)
 	mov		ip, sp
 	push		{r4-r10, lr}
 
-	ldm		ip, {r5-r7}		// load args 4-6
-	teq		r7, #0
-	addne		r5, r5, #1		// one extra block if final != 0
-
+	ldm		ip, {r5, r6}		// load args 4-5
 	vld1.8		{q0}, [r6]		// load counter
 	vrev32.8	q1, q0
 	vmov		r9, r10, d3
@@ -792,20 +787,19 @@ ENTRY(aesbs_ctr_encrypt)
 	adc		r7, r7, #0
 
 99:	vmov		q1, q0
+	sub		lr, r5, #1
 	vmov		q2, q0
+	adr		ip, 0f
 	vmov		q3, q0
+	and		lr, lr, #112
 	vmov		q4, q0
+	cmp		r5, #112
 	vmov		q5, q0
+	sub		ip, ip, lr, lsl #1
 	vmov		q6, q0
+	add		ip, ip, lr, lsr #2
 	vmov		q7, q0
-
-	adr		ip, 0f
-	sub		lr, r5, #1
-	and		lr, lr, #7
-	cmp		r5, #8
-	sub		ip, ip, lr, lsl #5
-	sub		ip, ip, lr, lsl #2
-	movlt		pc, ip			// computed goto if blocks < 8
+	movle		pc, ip			// computed goto if bytes < 112
 
 	next_ctr	q1
 	next_ctr	q2
@@ -820,12 +814,14 @@ ENTRY(aesbs_ctr_encrypt)
 	bl		aesbs_encrypt8
 
 	adr		ip, 1f
-	and		lr, r5, #7
-	cmp		r5, #8
-	movgt		r4, #0
-	ldrle		r4, [sp, #40]		// load final in the last round
-	sub		ip, ip, lr, lsl #2
-	movlt		pc, ip			// computed goto if blocks < 8
+	sub		lr, r5, #1
+	cmp		r5, #128
+	bic		lr, lr, #15
+	ands		r4, r5, #15		// preserves C flag
+	teqcs		r5, r5			// set Z flag if not last iteration
+	sub		ip, ip, lr, lsr #2
+	rsb		r4, r4, #16
+	movcc		pc, ip			// computed goto if bytes < 128
 
 	vld1.8		{q8}, [r1]!
 	vld1.8		{q9}, [r1]!
@@ -834,46 +830,70 @@ ENTRY(aesbs_ctr_encrypt)
 	vld1.8		{q12}, [r1]!
 	vld1.8		{q13}, [r1]!
 	vld1.8		{q14}, [r1]!
-	teq		r4, #0			// skip last block if 'final'
-1:	bne		2f
+1:	subne		r1, r1, r4
 	vld1.8		{q15}, [r1]!
 
-2:	adr		ip, 3f
-	cmp		r5, #8
-	sub		ip, ip, lr, lsl #3
-	movlt		pc, ip			// computed goto if blocks < 8
+	add		ip, ip, #2f - 1b
 
 	veor		q0, q0, q8
-	vst1.8		{q0}, [r0]!
 	veor		q1, q1, q9
-	vst1.8		{q1}, [r0]!
 	veor		q4, q4, q10
-	vst1.8		{q4}, [r0]!
 	veor		q6, q6, q11
-	vst1.8		{q6}, [r0]!
 	veor		q3, q3, q12
-	vst1.8		{q3}, [r0]!
 	veor		q7, q7, q13
-	vst1.8		{q7}, [r0]!
 	veor		q2, q2, q14
+	bne		3f
+	veor		q5, q5, q15
+
+	movcc		pc, ip			// computed goto if bytes < 128
+
+	vst1.8		{q0}, [r0]!
+	vst1.8		{q1}, [r0]!
+	vst1.8		{q4}, [r0]!
+	vst1.8		{q6}, [r0]!
+	vst1.8		{q3}, [r0]!
+	vst1.8		{q7}, [r0]!
 	vst1.8		{q2}, [r0]!
-	teq		r4, #0			// skip last block if 'final'
-	W(bne)		5f
-3:	veor		q5, q5, q15
+2:	subne		r0, r0, r4
 	vst1.8		{q5}, [r0]!
 
-4:	next_ctr	q0
+	next_ctr	q0
 
-	subs		r5, r5, #8
+	subs		r5, r5, #128
 	bgt		99b
 
 	vst1.8		{q0}, [r6]
 	pop		{r4-r10, pc}
 
-5:	vst1.8		{q5}, [r4]
-	b		4b
+3:	adr		lr, .Lpermute_table + 16
+	cmp		r5, #16			// Z flag remains cleared
+	sub		lr, lr, r4
+	vld1.8		{q8-q9}, [lr]
+	vtbl.8		d16, {q5}, d16
+	vtbl.8		d17, {q5}, d17
+	veor		q5, q8, q15
+	bcc		4f			// have to reload prev if R5 < 16
+	vtbx.8		d10, {q2}, d18
+	vtbx.8		d11, {q2}, d19
+	mov		pc, ip			// branch back to VST sequence
+
+4:	sub		r0, r0, r4
+	vshr.s8		q9, q9, #7		// create mask for VBIF
+	vld1.8		{q8}, [r0]		// reload
+	vbif		q5, q8, q9
+	vst1.8		{q5}, [r0]
+	pop		{r4-r10, pc}
 ENDPROC(aesbs_ctr_encrypt)
 
+	.align		6
+.Lpermute_table:
+	.byte		0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff
+	.byte		0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff
+	.byte		0x00, 0x01, 0x02, 0x03, 0x04, 0x05, 0x06, 0x07
+	.byte		0x08, 0x09, 0x0a, 0x0b, 0x0c, 0x0d, 0x0e, 0x0f
+	.byte		0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff
+	.byte		0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff
+
 	.macro		next_tweak, out, in, const, tmp
 	vshr.s64	\tmp, \in, #63
 	vand		\tmp, \tmp, \const
@@ -888,6 +908,7 @@ ENDPROC(aesbs_ctr_encrypt)
 	 * aesbs_xts_decrypt(u8 out[], u8 const in[], u8 const rk[], int rounds,
 	 *		     int blocks, u8 iv[], int reorder_last_tweak)
 	 */
+	.align		6
 __xts_prepare8:
 	vld1.8		{q14}, [r7]		// load iv
 	vmov.i32	d30, #0x87		// compose tweak mask vector
diff --git a/arch/arm/crypto/aes-neonbs-glue.c b/arch/arm/crypto/aes-neonbs-glue.c
index 5c6cd3c63cbc..f00f042ef357 100644
--- a/arch/arm/crypto/aes-neonbs-glue.c
+++ b/arch/arm/crypto/aes-neonbs-glue.c
@@ -37,7 +37,7 @@ asmlinkage void aesbs_cbc_decrypt(u8 out[], u8 const in[], u8 const rk[],
 				  int rounds, int blocks, u8 iv[]);
 
 asmlinkage void aesbs_ctr_encrypt(u8 out[], u8 const in[], u8 const rk[],
-				  int rounds, int blocks, u8 ctr[], u8 final[]);
+				  int rounds, int blocks, u8 ctr[]);
 
 asmlinkage void aesbs_xts_encrypt(u8 out[], u8 const in[], u8 const rk[],
 				  int rounds, int blocks, u8 iv[], int);
@@ -243,32 +243,25 @@ static int ctr_encrypt(struct skcipher_request *req)
 	err = skcipher_walk_virt(&walk, req, false);
 
 	while (walk.nbytes > 0) {
-		unsigned int blocks = walk.nbytes / AES_BLOCK_SIZE;
-		u8 *final = (walk.total % AES_BLOCK_SIZE) ? buf : NULL;
+		const u8 *src = walk.src.virt.addr;
+		u8 *dst = walk.dst.virt.addr;
+		int bytes = walk.nbytes;
 
-		if (walk.nbytes < walk.total) {
-			blocks = round_down(blocks,
-					    walk.stride / AES_BLOCK_SIZE);
-			final = NULL;
-		}
+		if (unlikely(bytes < AES_BLOCK_SIZE))
+			src = dst = memcpy(buf + sizeof(buf) - bytes,
+					   src, bytes);
+		else if (walk.nbytes < walk.total)
+			bytes &= ~(8 * AES_BLOCK_SIZE - 1);
 
 		kernel_neon_begin();
-		aesbs_ctr_encrypt(walk.dst.virt.addr, walk.src.virt.addr,
-				  ctx->rk, ctx->rounds, blocks, walk.iv, final);
+		aesbs_ctr_encrypt(dst, src, ctx->rk, ctx->rounds, bytes, walk.iv);
 		kernel_neon_end();
 
-		if (final) {
-			u8 *dst = walk.dst.virt.addr + blocks * AES_BLOCK_SIZE;
-			u8 *src = walk.src.virt.addr + blocks * AES_BLOCK_SIZE;
+		if (unlikely(bytes < AES_BLOCK_SIZE))
+			memcpy(walk.dst.virt.addr,
+			       buf + sizeof(buf) - bytes, bytes);
 
-			crypto_xor_cpy(dst, src, final,
-				       walk.total % AES_BLOCK_SIZE);
-
-			err = skcipher_walk_done(&walk, 0);
-			break;
-		}
-		err = skcipher_walk_done(&walk,
-					 walk.nbytes - blocks * AES_BLOCK_SIZE);
+		err = skcipher_walk_done(&walk, walk.nbytes - bytes);
 	}
 
 	return err;
diff --git a/arch/arm/crypto/blake2s-core.S b/arch/arm/crypto/blake2s-core.S
index 86345751bbf3..df40e46601f1 100644
--- a/arch/arm/crypto/blake2s-core.S
+++ b/arch/arm/crypto/blake2s-core.S
@@ -167,8 +167,8 @@
 .endm
 
 //
-// void blake2s_compress_arch(struct blake2s_state *state,
-//			      const u8 *block, size_t nblocks, u32 inc);
+// void blake2s_compress(struct blake2s_state *state,
+//			 const u8 *block, size_t nblocks, u32 inc);
 //
 // Only the first three fields of struct blake2s_state are used:
 //	u32 h[8];	(inout)
@@ -176,7 +176,7 @@
 //	u32 f[2];	(in)
 //
 	.align		5
-ENTRY(blake2s_compress_arch)
+ENTRY(blake2s_compress)
 	push		{r0-r2,r4-r11,lr}	// keep this an even number
 
 .Lnext_block:
@@ -303,4 +303,4 @@ ENTRY(blake2s_compress_arch)
 	str		r3, [r12], #4
 	bne		1b
 	b		.Lcopy_block_done
-ENDPROC(blake2s_compress_arch)
+ENDPROC(blake2s_compress)
diff --git a/arch/arm/crypto/blake2s-glue.c b/arch/arm/crypto/blake2s-glue.c
index f2cc1e5fc9ec..0238a70d9581 100644
--- a/arch/arm/crypto/blake2s-glue.c
+++ b/arch/arm/crypto/blake2s-glue.c
@@ -1,78 +1,7 @@
 // SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * BLAKE2s digest algorithm, ARM scalar implementation
- *
- * Copyright 2020 Google LLC
- */
 
 #include <crypto/internal/blake2s.h>
-#include <crypto/internal/hash.h>
-
 #include <linux/module.h>
 
 /* defined in blake2s-core.S */
-EXPORT_SYMBOL(blake2s_compress_arch);
-
-static int crypto_blake2s_update_arm(struct shash_desc *desc,
-				     const u8 *in, unsigned int inlen)
-{
-	return crypto_blake2s_update(desc, in, inlen, blake2s_compress_arch);
-}
-
-static int crypto_blake2s_final_arm(struct shash_desc *desc, u8 *out)
-{
-	return crypto_blake2s_final(desc, out, blake2s_compress_arch);
-}
-
-#define BLAKE2S_ALG(name, driver_name, digest_size)			\
-	{								\
-		.base.cra_name		= name,				\
-		.base.cra_driver_name	= driver_name,			\
-		.base.cra_priority	= 200,				\
-		.base.cra_flags		= CRYPTO_ALG_OPTIONAL_KEY,	\
-		.base.cra_blocksize	= BLAKE2S_BLOCK_SIZE,		\
-		.base.cra_ctxsize	= sizeof(struct blake2s_tfm_ctx), \
-		.base.cra_module	= THIS_MODULE,			\
-		.digestsize		= digest_size,			\
-		.setkey			= crypto_blake2s_setkey,	\
-		.init			= crypto_blake2s_init,		\
-		.update			= crypto_blake2s_update_arm,	\
-		.final			= crypto_blake2s_final_arm,	\
-		.descsize		= sizeof(struct blake2s_state),	\
-	}
-
-static struct shash_alg blake2s_arm_algs[] = {
-	BLAKE2S_ALG("blake2s-128", "blake2s-128-arm", BLAKE2S_128_HASH_SIZE),
-	BLAKE2S_ALG("blake2s-160", "blake2s-160-arm", BLAKE2S_160_HASH_SIZE),
-	BLAKE2S_ALG("blake2s-224", "blake2s-224-arm", BLAKE2S_224_HASH_SIZE),
-	BLAKE2S_ALG("blake2s-256", "blake2s-256-arm", BLAKE2S_256_HASH_SIZE),
-};
-
-static int __init blake2s_arm_mod_init(void)
-{
-	return IS_REACHABLE(CONFIG_CRYPTO_HASH) ?
-		crypto_register_shashes(blake2s_arm_algs,
-					ARRAY_SIZE(blake2s_arm_algs)) : 0;
-}
-
-static void __exit blake2s_arm_mod_exit(void)
-{
-	if (IS_REACHABLE(CONFIG_CRYPTO_HASH))
-		crypto_unregister_shashes(blake2s_arm_algs,
-					  ARRAY_SIZE(blake2s_arm_algs));
-}
-
-module_init(blake2s_arm_mod_init);
-module_exit(blake2s_arm_mod_exit);
-
-MODULE_DESCRIPTION("BLAKE2s digest algorithm, ARM scalar implementation");
-MODULE_LICENSE("GPL");
-MODULE_AUTHOR("Eric Biggers <ebiggers@google.com>");
-MODULE_ALIAS_CRYPTO("blake2s-128");
-MODULE_ALIAS_CRYPTO("blake2s-128-arm");
-MODULE_ALIAS_CRYPTO("blake2s-160");
-MODULE_ALIAS_CRYPTO("blake2s-160-arm");
-MODULE_ALIAS_CRYPTO("blake2s-224");
-MODULE_ALIAS_CRYPTO("blake2s-224-arm");
-MODULE_ALIAS_CRYPTO("blake2s-256");
-MODULE_ALIAS_CRYPTO("blake2s-256-arm");
+EXPORT_SYMBOL(blake2s_compress);
diff --git a/arch/arm/include/asm/arch_gicv3.h b/arch/arm/include/asm/arch_gicv3.h
index 413abfb42989..f82a819eb0db 100644
--- a/arch/arm/include/asm/arch_gicv3.h
+++ b/arch/arm/include/asm/arch_gicv3.h
@@ -48,6 +48,7 @@ static inline u32 read_ ## a64(void)		\
 	return read_sysreg(a32); 		\
 }						\
 
+CPUIF_MAP(ICC_EOIR1, ICC_EOIR1_EL1)
 CPUIF_MAP(ICC_PMR, ICC_PMR_EL1)
 CPUIF_MAP(ICC_AP0R0, ICC_AP0R0_EL1)
 CPUIF_MAP(ICC_AP0R1, ICC_AP0R1_EL1)
@@ -63,12 +64,6 @@ CPUIF_MAP(ICC_AP1R3, ICC_AP1R3_EL1)
 
 /* Low-level accessors */
 
-static inline void gic_write_eoir(u32 irq)
-{
-	write_sysreg(irq, ICC_EOIR1);
-	isb();
-}
-
 static inline void gic_write_dir(u32 val)
 {
 	write_sysreg(val, ICC_DIR);
diff --git a/arch/arm/include/asm/archrandom.h b/arch/arm/include/asm/archrandom.h
index a8e84ca5c2ee..cc4714eb1a75 100644
--- a/arch/arm/include/asm/archrandom.h
+++ b/arch/arm/include/asm/archrandom.h
@@ -7,4 +7,6 @@ static inline bool __init smccc_probe_trng(void)
 	return false;
 }
 
+#include <asm-generic/archrandom.h>
+
 #endif /* _ASM_ARCHRANDOM_H */
diff --git a/arch/arm/include/asm/assembler.h b/arch/arm/include/asm/assembler.h
index 7d23d4bb2168..90fbe4a3f9c8 100644
--- a/arch/arm/include/asm/assembler.h
+++ b/arch/arm/include/asm/assembler.h
@@ -86,6 +86,10 @@
 
 #define IMM12_MASK 0xfff
 
+/* the frame pointer used for stack unwinding */
+ARM(	fpreg	.req	r11	)
+THUMB(	fpreg	.req	r7	)
+
 /*
  * Enable and disable interrupts
  */
@@ -107,6 +111,16 @@
 	.endm
 #endif
 
+#if __LINUX_ARM_ARCH__ < 7
+	.macro	dsb, args
+	mcr	p15, 0, r0, c7, c10, 4
+	.endm
+
+	.macro	isb, args
+	mcr	p15, 0, r0, c7, c5, 4
+	.endm
+#endif
+
 	.macro asm_trace_hardirqs_off, save=1
 #if defined(CONFIG_TRACE_IRQFLAGS)
 	.if \save
@@ -199,43 +213,12 @@
 	.endm
 	.endr
 
-	.macro	get_current, rd
-#ifdef CONFIG_CURRENT_POINTER_IN_TPIDRURO
-	mrc	p15, 0, \rd, c13, c0, 3		@ get TPIDRURO register
-#else
-	get_thread_info \rd
-	ldr	\rd, [\rd, #TI_TASK]
-#endif
-	.endm
-
-	.macro	set_current, rn
-#ifdef CONFIG_CURRENT_POINTER_IN_TPIDRURO
-	mcr	p15, 0, \rn, c13, c0, 3		@ set TPIDRURO register
-#endif
-	.endm
-
-	.macro	reload_current, t1:req, t2:req
-#ifdef CONFIG_CURRENT_POINTER_IN_TPIDRURO
-	adr_l	\t1, __entry_task		@ get __entry_task base address
-	mrc	p15, 0, \t2, c13, c0, 4		@ get per-CPU offset
-	ldr	\t1, [\t1, \t2]			@ load variable
-	mcr	p15, 0, \t1, c13, c0, 3		@ store in TPIDRURO
-#endif
-	.endm
-
 /*
  * Get current thread_info.
  */
 	.macro	get_thread_info, rd
-#ifdef CONFIG_THREAD_INFO_IN_TASK
 	/* thread_info is the first member of struct task_struct */
 	get_current \rd
-#else
- ARM(	mov	\rd, sp, lsr #THREAD_SIZE_ORDER + PAGE_SHIFT	)
- THUMB(	mov	\rd, sp			)
- THUMB(	lsr	\rd, \rd, #THREAD_SIZE_ORDER + PAGE_SHIFT	)
-	mov	\rd, \rd, lsl #THREAD_SIZE_ORDER + PAGE_SHIFT
-#endif
 	.endm
 
 /*
@@ -288,6 +271,7 @@
  */
 #define ALT_UP(instr...)					\
 	.pushsection ".alt.smp.init", "a"			;\
+	.align	2						;\
 	.long	9998b - .					;\
 9997:	instr							;\
 	.if . - 9997b == 2					;\
@@ -299,6 +283,7 @@
 	.popsection
 #define ALT_UP_B(label)					\
 	.pushsection ".alt.smp.init", "a"			;\
+	.align	2						;\
 	.long	9998b - .					;\
 	W(b)	. + (label - 9998b)					;\
 	.popsection
@@ -308,6 +293,80 @@
 #define ALT_UP_B(label) b label
 #endif
 
+	/*
+	 * this_cpu_offset - load the per-CPU offset of this CPU into
+	 * 		     register 'rd'
+	 */
+	.macro		this_cpu_offset, rd:req
+#ifdef CONFIG_SMP
+ALT_SMP(mrc		p15, 0, \rd, c13, c0, 4)
+#ifdef CONFIG_CPU_V6
+ALT_UP_B(.L1_\@)
+.L0_\@:
+	.subsection	1
+.L1_\@: ldr_va		\rd, __per_cpu_offset
+	b		.L0_\@
+	.previous
+#endif
+#else
+	mov		\rd, #0
+#endif
+	.endm
+
+	/*
+	 * set_current - store the task pointer of this CPU's current task
+	 */
+	.macro		set_current, rn:req, tmp:req
+#if defined(CONFIG_CURRENT_POINTER_IN_TPIDRURO) || defined(CONFIG_SMP)
+9998:	mcr		p15, 0, \rn, c13, c0, 3		@ set TPIDRURO register
+#ifdef CONFIG_CPU_V6
+ALT_UP_B(.L0_\@)
+	.subsection	1
+.L0_\@: str_va		\rn, __current, \tmp
+	b		.L1_\@
+	.previous
+.L1_\@:
+#endif
+#else
+	str_va		\rn, __current, \tmp
+#endif
+	.endm
+
+	/*
+	 * get_current - load the task pointer of this CPU's current task
+	 */
+	.macro		get_current, rd:req
+#if defined(CONFIG_CURRENT_POINTER_IN_TPIDRURO) || defined(CONFIG_SMP)
+9998:	mrc		p15, 0, \rd, c13, c0, 3		@ get TPIDRURO register
+#ifdef CONFIG_CPU_V6
+ALT_UP_B(.L0_\@)
+	.subsection	1
+.L0_\@: ldr_va		\rd, __current
+	b		.L1_\@
+	.previous
+.L1_\@:
+#endif
+#else
+	ldr_va		\rd, __current
+#endif
+	.endm
+
+	/*
+	 * reload_current - reload the task pointer of this CPU's current task
+	 *		    into the TLS register
+	 */
+	.macro		reload_current, t1:req, t2:req
+#if defined(CONFIG_CURRENT_POINTER_IN_TPIDRURO) || defined(CONFIG_SMP)
+#ifdef CONFIG_CPU_V6
+ALT_SMP(nop)
+ALT_UP_B(.L0_\@)
+#endif
+	ldr_this_cpu	\t1, __entry_task, \t1, \t2
+	mcr		p15, 0, \t1, c13, c0, 3		@ store in TPIDRURO
+.L0_\@:
+#endif
+	.endm
+
 /*
  * Instruction barrier
  */
@@ -564,12 +623,12 @@ THUMB(	orr	\reg , \reg , #PSR_T_BIT	)
 	/*
 	 * mov_l - move a constant value or [relocated] address into a register
 	 */
-	.macro		mov_l, dst:req, imm:req
+	.macro		mov_l, dst:req, imm:req, cond
 	.if		__LINUX_ARM_ARCH__ < 7
-	ldr		\dst, =\imm
+	ldr\cond	\dst, =\imm
 	.else
-	movw		\dst, #:lower16:\imm
-	movt		\dst, #:upper16:\imm
+	movw\cond	\dst, #:lower16:\imm
+	movt\cond	\dst, #:upper16:\imm
 	.endif
 	.endm
 
@@ -607,6 +666,84 @@ THUMB(	orr	\reg , \reg , #PSR_T_BIT	)
 	__adldst_l	str, \src, \sym, \tmp, \cond
 	.endm
 
+	.macro		__ldst_va, op, reg, tmp, sym, cond, offset
+#if __LINUX_ARM_ARCH__ >= 7 || \
+    !defined(CONFIG_ARM_HAS_GROUP_RELOCS) || \
+    (defined(MODULE) && defined(CONFIG_ARM_MODULE_PLTS))
+	mov_l		\tmp, \sym, \cond
+#else
+	/*
+	 * Avoid a literal load, by emitting a sequence of ADD/LDR instructions
+	 * with the appropriate relocations. The combined sequence has a range
+	 * of -/+ 256 MiB, which should be sufficient for the core kernel and
+	 * for modules loaded into the module region.
+	 */
+	.globl		\sym
+	.reloc		.L0_\@, R_ARM_ALU_PC_G0_NC, \sym
+	.reloc		.L1_\@, R_ARM_ALU_PC_G1_NC, \sym
+	.reloc		.L2_\@, R_ARM_LDR_PC_G2, \sym
+.L0_\@: sub\cond	\tmp, pc, #8 - \offset
+.L1_\@: sub\cond	\tmp, \tmp, #4 - \offset
+.L2_\@:
+#endif
+	\op\cond	\reg, [\tmp, #\offset]
+	.endm
+
+	/*
+	 * ldr_va - load a 32-bit word from the virtual address of \sym
+	 */
+	.macro		ldr_va, rd:req, sym:req, cond, tmp, offset=0
+	.ifnb		\tmp
+	__ldst_va	ldr, \rd, \tmp, \sym, \cond, \offset
+	.else
+	__ldst_va	ldr, \rd, \rd, \sym, \cond, \offset
+	.endif
+	.endm
+
+	/*
+	 * str_va - store a 32-bit word to the virtual address of \sym
+	 */
+	.macro		str_va, rn:req, sym:req, tmp:req, cond
+	__ldst_va	str, \rn, \tmp, \sym, \cond, 0
+	.endm
+
+	/*
+	 * ldr_this_cpu_armv6 - Load a 32-bit word from the per-CPU variable 'sym',
+	 *			without using a temp register. Supported in ARM mode
+	 *			only.
+	 */
+	.macro		ldr_this_cpu_armv6, rd:req, sym:req
+	this_cpu_offset	\rd
+	.globl		\sym
+	.reloc		.L0_\@, R_ARM_ALU_PC_G0_NC, \sym
+	.reloc		.L1_\@, R_ARM_ALU_PC_G1_NC, \sym
+	.reloc		.L2_\@, R_ARM_LDR_PC_G2, \sym
+	add		\rd, \rd, pc
+.L0_\@: sub		\rd, \rd, #4
+.L1_\@: sub		\rd, \rd, #0
+.L2_\@: ldr		\rd, [\rd, #4]
+	.endm
+
+	/*
+	 * ldr_this_cpu - Load a 32-bit word from the per-CPU variable 'sym'
+	 *		  into register 'rd', which may be the stack pointer,
+	 *		  using 't1' and 't2' as general temp registers. These
+	 *		  are permitted to overlap with 'rd' if != sp
+	 */
+	.macro		ldr_this_cpu, rd:req, sym:req, t1:req, t2:req
+#ifndef CONFIG_SMP
+	ldr_va		\rd, \sym, tmp=\t1
+#elif __LINUX_ARM_ARCH__ >= 7 || \
+      !defined(CONFIG_ARM_HAS_GROUP_RELOCS) || \
+      (defined(MODULE) && defined(CONFIG_ARM_MODULE_PLTS))
+	this_cpu_offset	\t1
+	mov_l		\t2, \sym
+	ldr		\rd, [\t1, \t2]
+#else
+	ldr_this_cpu_armv6 \rd, \sym
+#endif
+	.endm
+
 	/*
 	 * rev_l - byte-swap a 32-bit value
 	 *
@@ -624,4 +761,19 @@ THUMB(	orr	\reg , \reg , #PSR_T_BIT	)
 	.endif
 	.endm
 
+	/*
+	 * bl_r - branch and link to register
+	 *
+	 * @dst: target to branch to
+	 * @c: conditional opcode suffix
+	 */
+	.macro		bl_r, dst:req, c
+	.if		__LINUX_ARM_ARCH__ < 6
+	mov\c		lr, pc
+	mov\c		pc, \dst
+	.else
+	blx\c		\dst
+	.endif
+	.endm
+
 #endif /* __ASM_ASSEMBLER_H__ */
diff --git a/arch/arm/include/asm/bitops.h b/arch/arm/include/asm/bitops.h
index c92e42a5c8f7..714440fa2fc6 100644
--- a/arch/arm/include/asm/bitops.h
+++ b/arch/arm/include/asm/bitops.h
@@ -160,18 +160,20 @@ extern int _test_and_change_bit(int nr, volatile unsigned long * p);
 /*
  * Little endian assembly bitops.  nr = 0 -> byte 0 bit 0.
  */
-extern int _find_first_zero_bit_le(const unsigned long *p, unsigned size);
-extern int _find_next_zero_bit_le(const unsigned long *p, int size, int offset);
-extern int _find_first_bit_le(const unsigned long *p, unsigned size);
-extern int _find_next_bit_le(const unsigned long *p, int size, int offset);
+unsigned long _find_first_zero_bit_le(const unsigned long *p, unsigned long size);
+unsigned long _find_next_zero_bit_le(const unsigned long *p,
+				     unsigned long size, unsigned long offset);
+unsigned long _find_first_bit_le(const unsigned long *p, unsigned long size);
+unsigned long _find_next_bit_le(const unsigned long *p, unsigned long size, unsigned long offset);
 
 /*
  * Big endian assembly bitops.  nr = 0 -> byte 3 bit 0.
  */
-extern int _find_first_zero_bit_be(const unsigned long *p, unsigned size);
-extern int _find_next_zero_bit_be(const unsigned long *p, int size, int offset);
-extern int _find_first_bit_be(const unsigned long *p, unsigned size);
-extern int _find_next_bit_be(const unsigned long *p, int size, int offset);
+unsigned long _find_first_zero_bit_be(const unsigned long *p, unsigned long size);
+unsigned long _find_next_zero_bit_be(const unsigned long *p,
+				     unsigned long size, unsigned long offset);
+unsigned long _find_first_bit_be(const unsigned long *p, unsigned long size);
+unsigned long _find_next_bit_be(const unsigned long *p, unsigned long size, unsigned long offset);
 
 #ifndef CONFIG_SMP
 /*
@@ -264,7 +266,6 @@ static inline int find_next_bit_le(const void *p, int size, int offset)
 
 #endif
 
-#include <asm-generic/bitops/find.h>
 #include <asm-generic/bitops/le.h>
 
 /*
diff --git a/arch/arm/include/asm/cacheflush.h b/arch/arm/include/asm/cacheflush.h
index 5e56288e343b..a094f964c869 100644
--- a/arch/arm/include/asm/cacheflush.h
+++ b/arch/arm/include/asm/cacheflush.h
@@ -445,15 +445,10 @@ static inline void __sync_cache_range_r(volatile void *p, size_t size)
  *   however some exceptions may exist.  Caveat emptor.
  *
  * - The clobber list is dictated by the call to v7_flush_dcache_*.
- *   fp is preserved to the stack explicitly prior disabling the cache
- *   since adding it to the clobber list is incompatible with having
- *   CONFIG_FRAME_POINTER=y.  ip is saved as well if ever r12-clobbering
- *   trampoline are inserted by the linker and to keep sp 64-bit aligned.
  */
 #define v7_exit_coherency_flush(level) \
 	asm volatile( \
 	".arch	armv7-a \n\t" \
-	"stmfd	sp!, {fp, ip} \n\t" \
 	"mrc	p15, 0, r0, c1, c0, 0	@ get SCTLR \n\t" \
 	"bic	r0, r0, #"__stringify(CR_C)" \n\t" \
 	"mcr	p15, 0, r0, c1, c0, 0	@ set SCTLR \n\t" \
@@ -463,10 +458,9 @@ static inline void __sync_cache_range_r(volatile void *p, size_t size)
 	"bic	r0, r0, #(1 << 6)	@ disable local coherency \n\t" \
 	"mcr	p15, 0, r0, c1, c0, 1	@ set ACTLR \n\t" \
 	"isb	\n\t" \
-	"dsb	\n\t" \
-	"ldmfd	sp!, {fp, ip}" \
-	: : : "r0","r1","r2","r3","r4","r5","r6","r7", \
-	      "r9","r10","lr","memory" )
+	"dsb" \
+	: : : "r0","r1","r2","r3","r4","r5","r6", \
+	      "r9","r10","ip","lr","memory" )
 
 void flush_uprobe_xol_access(struct page *page, unsigned long uaddr,
 			     void *kaddr, unsigned long len);
diff --git a/arch/arm/include/asm/current.h b/arch/arm/include/asm/current.h
index 6bf0aad672c3..1e1178bf176d 100644
--- a/arch/arm/include/asm/current.h
+++ b/arch/arm/include/asm/current.h
@@ -8,25 +8,18 @@
 #define _ASM_ARM_CURRENT_H
 
 #ifndef __ASSEMBLY__
+#include <asm/insn.h>
 
 struct task_struct;
 
-static inline void set_current(struct task_struct *cur)
-{
-	if (!IS_ENABLED(CONFIG_CURRENT_POINTER_IN_TPIDRURO))
-		return;
-
-	/* Set TPIDRURO */
-	asm("mcr p15, 0, %0, c13, c0, 3" :: "r"(cur) : "memory");
-}
-
-#ifdef CONFIG_CURRENT_POINTER_IN_TPIDRURO
+extern struct task_struct *__current;
 
-static inline struct task_struct *get_current(void)
+static __always_inline __attribute_const__ struct task_struct *get_current(void)
 {
 	struct task_struct *cur;
 
 #if __has_builtin(__builtin_thread_pointer) && \
+    defined(CONFIG_CURRENT_POINTER_IN_TPIDRURO) && \
     !(defined(CONFIG_THUMB2_KERNEL) && \
       defined(CONFIG_CC_IS_CLANG) && CONFIG_CLANG_VERSION < 130001)
 	/*
@@ -39,16 +32,39 @@ static inline struct task_struct *get_current(void)
 	 * https://github.com/ClangBuiltLinux/linux/issues/1485
 	 */
 	cur = __builtin_thread_pointer();
+#elif defined(CONFIG_CURRENT_POINTER_IN_TPIDRURO) || defined(CONFIG_SMP)
+	asm("0:	mrc p15, 0, %0, c13, c0, 3			\n\t"
+#ifdef CONFIG_CPU_V6
+	    "1:							\n\t"
+	    "	.subsection 1					\n\t"
+#if defined(CONFIG_ARM_HAS_GROUP_RELOCS) && \
+    !(defined(MODULE) && defined(CONFIG_ARM_MODULE_PLTS))
+	    "2: " LOAD_SYM_ARMV6(%0, __current) "		\n\t"
+	    "	b	1b					\n\t"
 #else
-	asm("mrc p15, 0, %0, c13, c0, 3" : "=r"(cur));
+	    "2:	ldr	%0, 3f					\n\t"
+	    "	ldr	%0, [%0]				\n\t"
+	    "	b	1b					\n\t"
+	    "3:	.long	__current				\n\t"
+#endif
+	    "	.previous					\n\t"
+	    "	.pushsection \".alt.smp.init\", \"a\"		\n\t"
+	    "	.long	0b - .					\n\t"
+	    "	b	. + (2b - 0b)				\n\t"
+	    "	.popsection					\n\t"
+#endif
+	    : "=r"(cur));
+#elif __LINUX_ARM_ARCH__>= 7 || \
+      !defined(CONFIG_ARM_HAS_GROUP_RELOCS) || \
+      (defined(MODULE) && defined(CONFIG_ARM_MODULE_PLTS))
+	cur = __current;
+#else
+	asm(LOAD_SYM_ARMV6(%0, __current) : "=r"(cur));
 #endif
 	return cur;
 }
 
 #define current get_current()
-#else
-#include <asm-generic/current.h>
-#endif /* CONFIG_CURRENT_POINTER_IN_TPIDRURO */
 
 #endif /* __ASSEMBLY__ */
 
diff --git a/arch/arm/include/asm/device.h b/arch/arm/include/asm/device.h
index be666f58bf7a..c6beb1708c64 100644
--- a/arch/arm/include/asm/device.h
+++ b/arch/arm/include/asm/device.h
@@ -6,13 +6,9 @@
 #define ASMARM_DEVICE_H
 
 struct dev_archdata {
-#ifdef CONFIG_DMABOUNCE
-	struct dmabounce_device_info *dmabounce;
-#endif
 #ifdef CONFIG_ARM_DMA_USE_IOMMU
 	struct dma_iommu_mapping	*mapping;
 #endif
-	unsigned int dma_coherent:1;
 	unsigned int dma_ops_setup:1;
 };
 
diff --git a/arch/arm/include/asm/dma-direct.h b/arch/arm/include/asm/dma-direct.h
deleted file mode 100644
index 77fcb7ee5ec9..000000000000
--- a/arch/arm/include/asm/dma-direct.h
+++ /dev/null
@@ -1,48 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-#ifndef ASM_ARM_DMA_DIRECT_H
-#define ASM_ARM_DMA_DIRECT_H 1
-
-#include <asm/memory.h>
-
-/*
- * dma_to_pfn/pfn_to_dma/virt_to_dma are architecture private
- * functions used internally by the DMA-mapping API to provide DMA
- * addresses. They must not be used by drivers.
- */
-static inline dma_addr_t pfn_to_dma(struct device *dev, unsigned long pfn)
-{
-	if (dev && dev->dma_range_map)
-		pfn = PFN_DOWN(translate_phys_to_dma(dev, PFN_PHYS(pfn)));
-	return (dma_addr_t)__pfn_to_bus(pfn);
-}
-
-static inline unsigned long dma_to_pfn(struct device *dev, dma_addr_t addr)
-{
-	unsigned long pfn = __bus_to_pfn(addr);
-
-	if (dev && dev->dma_range_map)
-		pfn = PFN_DOWN(translate_dma_to_phys(dev, PFN_PHYS(pfn)));
-	return pfn;
-}
-
-static inline dma_addr_t virt_to_dma(struct device *dev, void *addr)
-{
-	if (dev)
-		return pfn_to_dma(dev, virt_to_pfn(addr));
-
-	return (dma_addr_t)__virt_to_bus((unsigned long)(addr));
-}
-
-static inline dma_addr_t phys_to_dma(struct device *dev, phys_addr_t paddr)
-{
-	unsigned int offset = paddr & ~PAGE_MASK;
-	return pfn_to_dma(dev, __phys_to_pfn(paddr)) + offset;
-}
-
-static inline phys_addr_t dma_to_phys(struct device *dev, dma_addr_t dev_addr)
-{
-	unsigned int offset = dev_addr & ~PAGE_MASK;
-	return __pfn_to_phys(dma_to_pfn(dev, dev_addr)) + offset;
-}
-
-#endif /* ASM_ARM_DMA_DIRECT_H */
diff --git a/arch/arm/include/asm/dma-mapping.h b/arch/arm/include/asm/dma-mapping.h
deleted file mode 100644
index 77082246a5e1..000000000000
--- a/arch/arm/include/asm/dma-mapping.h
+++ /dev/null
@@ -1,128 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-#ifndef ASMARM_DMA_MAPPING_H
-#define ASMARM_DMA_MAPPING_H
-
-#ifdef __KERNEL__
-
-#include <linux/mm_types.h>
-#include <linux/scatterlist.h>
-
-#include <xen/xen.h>
-#include <asm/xen/hypervisor.h>
-
-extern const struct dma_map_ops arm_dma_ops;
-extern const struct dma_map_ops arm_coherent_dma_ops;
-
-static inline const struct dma_map_ops *get_arch_dma_ops(struct bus_type *bus)
-{
-	if (IS_ENABLED(CONFIG_MMU) && !IS_ENABLED(CONFIG_ARM_LPAE))
-		return &arm_dma_ops;
-	return NULL;
-}
-
-/**
- * arm_dma_alloc - allocate consistent memory for DMA
- * @dev: valid struct device pointer, or NULL for ISA and EISA-like devices
- * @size: required memory size
- * @handle: bus-specific DMA address
- * @attrs: optinal attributes that specific mapping properties
- *
- * Allocate some memory for a device for performing DMA.  This function
- * allocates pages, and will return the CPU-viewed address, and sets @handle
- * to be the device-viewed address.
- */
-extern void *arm_dma_alloc(struct device *dev, size_t size, dma_addr_t *handle,
-			   gfp_t gfp, unsigned long attrs);
-
-/**
- * arm_dma_free - free memory allocated by arm_dma_alloc
- * @dev: valid struct device pointer, or NULL for ISA and EISA-like devices
- * @size: size of memory originally requested in dma_alloc_coherent
- * @cpu_addr: CPU-view address returned from dma_alloc_coherent
- * @handle: device-view address returned from dma_alloc_coherent
- * @attrs: optinal attributes that specific mapping properties
- *
- * Free (and unmap) a DMA buffer previously allocated by
- * arm_dma_alloc().
- *
- * References to memory and mappings associated with cpu_addr/handle
- * during and after this call executing are illegal.
- */
-extern void arm_dma_free(struct device *dev, size_t size, void *cpu_addr,
-			 dma_addr_t handle, unsigned long attrs);
-
-/**
- * arm_dma_mmap - map a coherent DMA allocation into user space
- * @dev: valid struct device pointer, or NULL for ISA and EISA-like devices
- * @vma: vm_area_struct describing requested user mapping
- * @cpu_addr: kernel CPU-view address returned from dma_alloc_coherent
- * @handle: device-view address returned from dma_alloc_coherent
- * @size: size of memory originally requested in dma_alloc_coherent
- * @attrs: optinal attributes that specific mapping properties
- *
- * Map a coherent DMA buffer previously allocated by dma_alloc_coherent
- * into user space.  The coherent DMA buffer must not be freed by the
- * driver until the user space mapping has been released.
- */
-extern int arm_dma_mmap(struct device *dev, struct vm_area_struct *vma,
-			void *cpu_addr, dma_addr_t dma_addr, size_t size,
-			unsigned long attrs);
-
-/*
- * For SA-1111, IXP425, and ADI systems  the dma-mapping functions are "magic"
- * and utilize bounce buffers as needed to work around limited DMA windows.
- *
- * On the SA-1111, a bug limits DMA to only certain regions of RAM.
- * On the IXP425, the PCI inbound window is 64MB (256MB total RAM)
- * On some ADI engineering systems, PCI inbound window is 32MB (12MB total RAM)
- *
- * The following are helper functions used by the dmabounce subystem
- *
- */
-
-/**
- * dmabounce_register_dev
- *
- * @dev: valid struct device pointer
- * @small_buf_size: size of buffers to use with small buffer pool
- * @large_buf_size: size of buffers to use with large buffer pool (can be 0)
- * @needs_bounce_fn: called to determine whether buffer needs bouncing
- *
- * This function should be called by low-level platform code to register
- * a device as requireing DMA buffer bouncing. The function will allocate
- * appropriate DMA pools for the device.
- */
-extern int dmabounce_register_dev(struct device *, unsigned long,
-		unsigned long, int (*)(struct device *, dma_addr_t, size_t));
-
-/**
- * dmabounce_unregister_dev
- *
- * @dev: valid struct device pointer
- *
- * This function should be called by low-level platform code when device
- * that was previously registered with dmabounce_register_dev is removed
- * from the system.
- *
- */
-extern void dmabounce_unregister_dev(struct device *);
-
-
-
-/*
- * The scatter list versions of the above methods.
- */
-extern int arm_dma_map_sg(struct device *, struct scatterlist *, int,
-		enum dma_data_direction, unsigned long attrs);
-extern void arm_dma_unmap_sg(struct device *, struct scatterlist *, int,
-		enum dma_data_direction, unsigned long attrs);
-extern void arm_dma_sync_sg_for_cpu(struct device *, struct scatterlist *, int,
-		enum dma_data_direction);
-extern void arm_dma_sync_sg_for_device(struct device *, struct scatterlist *, int,
-		enum dma_data_direction);
-extern int arm_dma_get_sgtable(struct device *dev, struct sg_table *sgt,
-		void *cpu_addr, dma_addr_t dma_addr, size_t size,
-		unsigned long attrs);
-
-#endif /* __KERNEL__ */
-#endif
diff --git a/arch/arm/include/asm/dma.h b/arch/arm/include/asm/dma.h
index a81dda65c576..c6aded1b069c 100644
--- a/arch/arm/include/asm/dma.h
+++ b/arch/arm/include/asm/dma.h
@@ -10,7 +10,7 @@
 #else
 #define MAX_DMA_ADDRESS	({ \
 	extern phys_addr_t arm_dma_zone_size; \
-	arm_dma_zone_size && arm_dma_zone_size < (0x10000000 - PAGE_OFFSET) ? \
+	arm_dma_zone_size && arm_dma_zone_size < (0x100000000ULL - PAGE_OFFSET) ? \
 		(PAGE_OFFSET + arm_dma_zone_size) : 0xffffffffUL; })
 #endif
 
@@ -106,7 +106,7 @@ extern void set_dma_sg(unsigned int chan, struct scatterlist *sg, int nr_sg);
  */
 extern void __set_dma_addr(unsigned int chan, void *addr);
 #define set_dma_addr(chan, addr)				\
-	__set_dma_addr(chan, (void *)__bus_to_virt(addr))
+	__set_dma_addr(chan, (void *)isa_bus_to_virt(addr))
 
 /* Set the DMA byte count for this channel
  *
@@ -143,10 +143,4 @@ extern int  get_dma_residue(unsigned int chan);
 
 #endif /* CONFIG_ISA_DMA_API */
 
-#ifdef CONFIG_PCI
-extern int isa_dma_bridge_buggy;
-#else
-#define isa_dma_bridge_buggy    (0)
-#endif
-
 #endif /* __ASM_ARM_DMA_H */
diff --git a/arch/arm/include/asm/domain.h b/arch/arm/include/asm/domain.h
index f1d0a7807cd0..41536feb4392 100644
--- a/arch/arm/include/asm/domain.h
+++ b/arch/arm/include/asm/domain.h
@@ -112,19 +112,6 @@ static __always_inline void set_domain(unsigned int val)
 }
 #endif
 
-#ifdef CONFIG_CPU_USE_DOMAINS
-#define modify_domain(dom,type)					\
-	do {							\
-		unsigned int domain = get_domain();		\
-		domain &= ~domain_mask(dom);			\
-		domain = domain | domain_val(dom, type);	\
-		set_domain(domain);				\
-	} while (0)
-
-#else
-static inline void modify_domain(unsigned dom, unsigned type)	{ }
-#endif
-
 /*
  * Generate the T (user) versions of the LDR/STR and related
  * instructions (inline assembly)
diff --git a/arch/arm/include/asm/efi.h b/arch/arm/include/asm/efi.h
index a6f3b179e8a9..4bdd930167c0 100644
--- a/arch/arm/include/asm/efi.h
+++ b/arch/arm/include/asm/efi.h
@@ -17,7 +17,7 @@
 
 #ifdef CONFIG_EFI
 void efi_init(void);
-extern void efifb_setup_from_dmi(struct screen_info *si, const char *opt);
+void arm_efi_init(void);
 
 int efi_create_mapping(struct mm_struct *mm, efi_memory_desc_t *md);
 int efi_set_mapping_permissions(struct mm_struct *mm, efi_memory_desc_t *md);
@@ -25,13 +25,6 @@ int efi_set_mapping_permissions(struct mm_struct *mm, efi_memory_desc_t *md);
 #define arch_efi_call_virt_setup()	efi_virtmap_load()
 #define arch_efi_call_virt_teardown()	efi_virtmap_unload()
 
-#define arch_efi_call_virt(p, f, args...)				\
-({									\
-	efi_##f##_t *__f;						\
-	__f = p->f;							\
-	__f(args);							\
-})
-
 #define ARCH_EFI_IRQ_FLAGS_MASK \
 	(PSR_J_BIT | PSR_E_BIT | PSR_A_BIT | PSR_I_BIT | PSR_F_BIT | \
 	 PSR_T_BIT | MODE_MASK)
@@ -45,7 +38,7 @@ void efi_virtmap_load(void);
 void efi_virtmap_unload(void);
 
 #else
-#define efi_init()
+#define arm_efi_init()
 #endif /* CONFIG_EFI */
 
 /* arch specific definitions used by the stub code */
diff --git a/arch/arm/include/asm/elf.h b/arch/arm/include/asm/elf.h
index b8102a6ddf16..d68101655b74 100644
--- a/arch/arm/include/asm/elf.h
+++ b/arch/arm/include/asm/elf.h
@@ -61,6 +61,9 @@ typedef struct user_fp elf_fpregset_t;
 #define R_ARM_MOVT_ABS		44
 #define R_ARM_MOVW_PREL_NC	45
 #define R_ARM_MOVT_PREL		46
+#define R_ARM_ALU_PC_G0_NC	57
+#define R_ARM_ALU_PC_G1_NC	59
+#define R_ARM_LDR_PC_G2		63
 
 #define R_ARM_THM_CALL		10
 #define R_ARM_THM_JUMP24	30
diff --git a/arch/arm/include/asm/entry-macro-multi.S b/arch/arm/include/asm/entry-macro-multi.S
deleted file mode 100644
index dfc6bfa43012..000000000000
--- a/arch/arm/include/asm/entry-macro-multi.S
+++ /dev/null
@@ -1,40 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-#include <asm/assembler.h>
-
-/*
- * Interrupt handling.  Preserves r7, r8, r9
- */
-	.macro	arch_irq_handler_default
-	get_irqnr_preamble r6, lr
-1:	get_irqnr_and_base r0, r2, r6, lr
-	movne	r1, sp
-	@
-	@ routine called with r0 = irq number, r1 = struct pt_regs *
-	@
-	badrne	lr, 1b
-	bne	asm_do_IRQ
-
-#ifdef CONFIG_SMP
-	/*
-	 * XXX
-	 *
-	 * this macro assumes that irqstat (r2) and base (r6) are
-	 * preserved from get_irqnr_and_base above
-	 */
-	ALT_SMP(test_for_ipi r0, r2, r6, lr)
-	ALT_UP_B(9997f)
-	movne	r1, sp
-	badrne	lr, 1b
-	bne	do_IPI
-#endif
-9997:
-	.endm
-
-	.macro	arch_irq_handler, symbol_name
-	.align	5
-	.global \symbol_name
-\symbol_name:
-	mov	r8, lr
-	arch_irq_handler_default
-	ret	r8
-	.endm
diff --git a/arch/arm/include/asm/fpstate.h b/arch/arm/include/asm/fpstate.h
index ca42fd9ae0b3..e29d9c7a5238 100644
--- a/arch/arm/include/asm/fpstate.h
+++ b/arch/arm/include/asm/fpstate.h
@@ -46,9 +46,6 @@ union vfp_state {
 	struct vfp_hard_struct	hard;
 };
 
-extern void vfp_flush_thread(union vfp_state *);
-extern void vfp_release_thread(union vfp_state *);
-
 #define FP_HARD_SIZE 35
 
 struct fp_hard_struct {
diff --git a/arch/arm/include/asm/ftrace.h b/arch/arm/include/asm/ftrace.h
index a4dbac07e4ef..7e9251ca29fe 100644
--- a/arch/arm/include/asm/ftrace.h
+++ b/arch/arm/include/asm/ftrace.h
@@ -2,6 +2,8 @@
 #ifndef _ASM_ARM_FTRACE
 #define _ASM_ARM_FTRACE
 
+#define HAVE_FUNCTION_GRAPH_FP_TEST
+
 #ifdef CONFIG_DYNAMIC_FTRACE_WITH_REGS
 #define ARCH_SUPPORTS_FTRACE_OPS 1
 #endif
@@ -48,7 +50,7 @@ void *return_address(unsigned int);
 
 static inline void *return_address(unsigned int level)
 {
-	return NULL;
+       return NULL;
 }
 
 #endif
diff --git a/arch/arm/include/asm/hardware/cache-aurora-l2.h b/arch/arm/include/asm/hardware/cache-aurora-l2.h
index 39769ffa0051..9694808ee97c 100644
--- a/arch/arm/include/asm/hardware/cache-aurora-l2.h
+++ b/arch/arm/include/asm/hardware/cache-aurora-l2.h
@@ -1,3 +1,4 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * AURORA shared L2 cache controller support
  *
@@ -5,10 +6,6 @@
  *
  * Yehuda Yitschak <yehuday@marvell.com>
  * Gregory CLEMENT <gregory.clement@free-electrons.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #ifndef __ASM_ARM_HARDWARE_AURORA_L2_H
diff --git a/arch/arm/include/asm/hardware/cache-feroceon-l2.h b/arch/arm/include/asm/hardware/cache-feroceon-l2.h
index 12e1588dc4f1..eb2e7b7f70a8 100644
--- a/arch/arm/include/asm/hardware/cache-feroceon-l2.h
+++ b/arch/arm/include/asm/hardware/cache-feroceon-l2.h
@@ -1,13 +1,9 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * arch/arm/include/asm/hardware/cache-feroceon-l2.h
  *
  * Copyright (C) 2008 Marvell Semiconductor
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 extern void __init feroceon_l2_init(int l2_wt_override);
 extern int __init feroceon_of_init(void);
-
diff --git a/arch/arm/include/asm/hardware/cache-tauros2.h b/arch/arm/include/asm/hardware/cache-tauros2.h
index 295e2e40151b..4e493facaa31 100644
--- a/arch/arm/include/asm/hardware/cache-tauros2.h
+++ b/arch/arm/include/asm/hardware/cache-tauros2.h
@@ -1,11 +1,8 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * arch/arm/include/asm/hardware/cache-tauros2.h
  *
  * Copyright (C) 2008 Marvell Semiconductor
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #define CACHE_TAUROS2_PREFETCH_ON	(1 << 0)
diff --git a/arch/arm/include/asm/hardware/dec21285.h b/arch/arm/include/asm/hardware/dec21285.h
index 3f18a56a025d..894f2a635cbb 100644
--- a/arch/arm/include/asm/hardware/dec21285.h
+++ b/arch/arm/include/asm/hardware/dec21285.h
@@ -22,6 +22,13 @@
 #define DC21285_IO(x)		(x)
 #endif
 
+/*
+ * The footbridge is programmed to expose the system RAM at 0xe0000000.
+ * The requirement is that the RAM isn't placed at bus address 0, which
+ * would clash with VGA cards.
+ */
+#define BUS_OFFSET 0xe0000000
+
 #define CSR_PCICMD		DC21285_IO(0x0004)
 #define CSR_CLASSREV		DC21285_IO(0x0008)
 #define CSR_PCICACHELINESIZE	DC21285_IO(0x000c)
@@ -81,19 +88,6 @@
 #define SA110_CNTL_XCSDIR(x)		((x)<<28)
 #define SA110_CNTL_PCICFN		(1 << 31)
 
-/*
- * footbridge_cfn_mode() is used when we want
- * to check whether we are the central function
- */
-#define __footbridge_cfn_mode() (*CSR_SA110_CNTL & SA110_CNTL_PCICFN)
-#if defined(CONFIG_FOOTBRIDGE_HOST) && defined(CONFIG_FOOTBRIDGE_ADDIN)
-#define footbridge_cfn_mode() __footbridge_cfn_mode()
-#elif defined(CONFIG_FOOTBRIDGE_HOST)
-#define footbridge_cfn_mode() (1)
-#else
-#define footbridge_cfn_mode() (0)
-#endif
-
 #define CSR_PCIADDR_EXTN	DC21285_IO(0x0140)
 #define CSR_PREFETCHMEMRANGE	DC21285_IO(0x0144)
 #define CSR_XBUS_CYCLE		DC21285_IO(0x0148)
diff --git a/arch/arm/include/asm/hardware/entry-macro-iomd.S b/arch/arm/include/asm/hardware/entry-macro-iomd.S
deleted file mode 100644
index f7692731e514..000000000000
--- a/arch/arm/include/asm/hardware/entry-macro-iomd.S
+++ /dev/null
@@ -1,131 +0,0 @@
-/*
- * arch/arm/include/asm/hardware/entry-macro-iomd.S
- *
- * Low-level IRQ helper macros for IOC/IOMD based platforms
- *
- * This file is licensed under  the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-/* IOC / IOMD based hardware */
-#include <asm/hardware/iomd.h>
-
-		.macro	get_irqnr_and_base, irqnr, irqstat, base, tmp
-		ldrb	\irqstat, [\base, #IOMD_IRQREQB]	@ get high priority first
-		ldr	\tmp, =irq_prio_h
-		teq	\irqstat, #0
-#ifdef IOMD_BASE
-		ldrbeq	\irqstat, [\base, #IOMD_DMAREQ]	@ get dma
-		addeq	\tmp, \tmp, #256		@ irq_prio_h table size
-		teqeq	\irqstat, #0
-		bne	2406f
-#endif
-		ldrbeq	\irqstat, [\base, #IOMD_IRQREQA]	@ get low priority
-		addeq	\tmp, \tmp, #256		@ irq_prio_d table size
-		teqeq	\irqstat, #0
-#ifdef IOMD_IRQREQC
-		ldrbeq	\irqstat, [\base, #IOMD_IRQREQC]
-		addeq	\tmp, \tmp, #256		@ irq_prio_l table size
-		teqeq	\irqstat, #0
-#endif
-#ifdef IOMD_IRQREQD
-		ldrbeq	\irqstat, [\base, #IOMD_IRQREQD]
-		addeq	\tmp, \tmp, #256		@ irq_prio_lc table size
-		teqeq	\irqstat, #0
-#endif
-2406:		ldrbne	\irqnr, [\tmp, \irqstat]	@ get IRQ number
-		.endm
-
-/*
- * Interrupt table (incorporates priority).  Please note that we
- * rely on the order of these tables (see above code).
- */
-		.align	5
-irq_prio_h:	.byte	 0, 8, 9, 8,10,10,10,10,11,11,11,11,10,10,10,10
-		.byte	12, 8, 9, 8,10,10,10,10,11,11,11,11,10,10,10,10
-		.byte	13,13,13,13,10,10,10,10,11,11,11,11,10,10,10,10
-		.byte	13,13,13,13,10,10,10,10,11,11,11,11,10,10,10,10
-		.byte	14,14,14,14,10,10,10,10,11,11,11,11,10,10,10,10
-		.byte	14,14,14,14,10,10,10,10,11,11,11,11,10,10,10,10
-		.byte	13,13,13,13,10,10,10,10,11,11,11,11,10,10,10,10
-		.byte	13,13,13,13,10,10,10,10,11,11,11,11,10,10,10,10
-		.byte	15,15,15,15,10,10,10,10,11,11,11,11,10,10,10,10
-		.byte	15,15,15,15,10,10,10,10,11,11,11,11,10,10,10,10
-		.byte	13,13,13,13,10,10,10,10,11,11,11,11,10,10,10,10
-		.byte	13,13,13,13,10,10,10,10,11,11,11,11,10,10,10,10
-		.byte	15,15,15,15,10,10,10,10,11,11,11,11,10,10,10,10
-		.byte	15,15,15,15,10,10,10,10,11,11,11,11,10,10,10,10
-		.byte	13,13,13,13,10,10,10,10,11,11,11,11,10,10,10,10
-		.byte	13,13,13,13,10,10,10,10,11,11,11,11,10,10,10,10
-#ifdef IOMD_BASE
-irq_prio_d:	.byte	 0,16,17,16,18,16,17,16,19,16,17,16,18,16,17,16
-		.byte	20,16,17,16,18,16,17,16,19,16,17,16,18,16,17,16
-		.byte	21,16,17,16,18,16,17,16,19,16,17,16,18,16,17,16
-		.byte	21,16,17,16,18,16,17,16,19,16,17,16,18,16,17,16
-		.byte	22,16,17,16,18,16,17,16,19,16,17,16,18,16,17,16
-		.byte	22,16,17,16,18,16,17,16,19,16,17,16,18,16,17,16
-		.byte	21,16,17,16,18,16,17,16,19,16,17,16,18,16,17,16
-		.byte	21,16,17,16,18,16,17,16,19,16,17,16,18,16,17,16
-		.byte	23,16,17,16,18,16,17,16,19,16,17,16,18,16,17,16
-		.byte	23,16,17,16,18,16,17,16,19,16,17,16,18,16,17,16
-		.byte	21,16,17,16,18,16,17,16,19,16,17,16,18,16,17,16
-		.byte	21,16,17,16,18,16,17,16,19,16,17,16,18,16,17,16
-		.byte	22,16,17,16,18,16,17,16,19,16,17,16,18,16,17,16
-		.byte	22,16,17,16,18,16,17,16,19,16,17,16,18,16,17,16
-		.byte	21,16,17,16,18,16,17,16,19,16,17,16,18,16,17,16
-		.byte	21,16,17,16,18,16,17,16,19,16,17,16,18,16,17,16
-#endif
-irq_prio_l:	.byte	 0, 0, 1, 0, 2, 2, 2, 2, 3, 3, 3, 3, 3, 3, 3, 3
-		.byte	 4, 0, 1, 0, 2, 2, 2, 2, 3, 3, 3, 3, 3, 3, 3, 3
-		.byte	 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5
-		.byte	 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5
-		.byte	 6, 6, 6, 6, 6, 6, 6, 6, 3, 3, 3, 3, 3, 3, 3, 3
-		.byte	 6, 6, 6, 6, 6, 6, 6, 6, 3, 3, 3, 3, 3, 3, 3, 3
-		.byte	 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5
-		.byte	 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5
-		.byte	 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7
-		.byte	 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7
-		.byte	 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7
-		.byte	 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7
-		.byte	 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7
-		.byte	 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7
-		.byte	 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7
-		.byte	 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7
-#ifdef IOMD_IRQREQC
-irq_prio_lc:	.byte	24,24,25,24,26,26,26,26,27,27,27,27,27,27,27,27
-		.byte	28,24,25,24,26,26,26,26,27,27,27,27,27,27,27,27
-		.byte	29,29,29,29,29,29,29,29,29,29,29,29,29,29,29,29
-		.byte	29,29,29,29,29,29,29,29,29,29,29,29,29,29,29,29
-		.byte	30,30,30,30,30,30,30,30,27,27,27,27,27,27,27,27
-		.byte	30,30,30,30,30,30,30,30,27,27,27,27,27,27,27,27
-		.byte	29,29,29,29,29,29,29,29,29,29,29,29,29,29,29,29
-		.byte	29,29,29,29,29,29,29,29,29,29,29,29,29,29,29,29
-		.byte	31,31,31,31,31,31,31,31,31,31,31,31,31,31,31,31
-		.byte	31,31,31,31,31,31,31,31,31,31,31,31,31,31,31,31
-		.byte	31,31,31,31,31,31,31,31,31,31,31,31,31,31,31,31
-		.byte	31,31,31,31,31,31,31,31,31,31,31,31,31,31,31,31
-		.byte	31,31,31,31,31,31,31,31,31,31,31,31,31,31,31,31
-		.byte	31,31,31,31,31,31,31,31,31,31,31,31,31,31,31,31
-		.byte	31,31,31,31,31,31,31,31,31,31,31,31,31,31,31,31
-		.byte	31,31,31,31,31,31,31,31,31,31,31,31,31,31,31,31
-#endif
-#ifdef IOMD_IRQREQD
-irq_prio_ld:	.byte	40,40,41,40,42,42,42,42,43,43,43,43,43,43,43,43
-		.byte	44,40,41,40,42,42,42,42,43,43,43,43,43,43,43,43
-		.byte	45,45,45,45,45,45,45,45,45,45,45,45,45,45,45,45
-		.byte	45,45,45,45,45,45,45,45,45,45,45,45,45,45,45,45
-		.byte	46,46,46,46,46,46,46,46,43,43,43,43,43,43,43,43
-		.byte	46,46,46,46,46,46,46,46,43,43,43,43,43,43,43,43
-		.byte	45,45,45,45,45,45,45,45,45,45,45,45,45,45,45,45
-		.byte	45,45,45,45,45,45,45,45,45,45,45,45,45,45,45,45
-		.byte	47,47,47,47,47,47,47,47,47,47,47,47,47,47,47,47
-		.byte	47,47,47,47,47,47,47,47,47,47,47,47,47,47,47,47
-		.byte	47,47,47,47,47,47,47,47,47,47,47,47,47,47,47,47
-		.byte	47,47,47,47,47,47,47,47,47,47,47,47,47,47,47,47
-		.byte	47,47,47,47,47,47,47,47,47,47,47,47,47,47,47,47
-		.byte	47,47,47,47,47,47,47,47,47,47,47,47,47,47,47,47
-		.byte	47,47,47,47,47,47,47,47,47,47,47,47,47,47,47,47
-		.byte	47,47,47,47,47,47,47,47,47,47,47,47,47,47,47,47
-#endif
-
diff --git a/arch/arm/include/asm/hardware/sa1111.h b/arch/arm/include/asm/hardware/sa1111.h
index 2e70db6f22ea..d8c6f8a99dfa 100644
--- a/arch/arm/include/asm/hardware/sa1111.h
+++ b/arch/arm/include/asm/hardware/sa1111.h
@@ -13,8 +13,6 @@
 #ifndef _ASM_ARCH_SA1111
 #define _ASM_ARCH_SA1111
 
-#include <mach/bitfield.h>
-
 /*
  * Don't ask the (SAC) DMA engines to move less than this amount.
  */
diff --git a/arch/arm/include/asm/insn.h b/arch/arm/include/asm/insn.h
index 5475cbf9fb6b..faf3d1c28368 100644
--- a/arch/arm/include/asm/insn.h
+++ b/arch/arm/include/asm/insn.h
@@ -2,6 +2,23 @@
 #ifndef __ASM_ARM_INSN_H
 #define __ASM_ARM_INSN_H
 
+#include <linux/types.h>
+
+/*
+ * Avoid a literal load by emitting a sequence of ADD/LDR instructions with the
+ * appropriate relocations. The combined sequence has a range of -/+ 256 MiB,
+ * which should be sufficient for the core kernel as well as modules loaded
+ * into the module region. (Not supported by LLD before release 14)
+ */
+#define LOAD_SYM_ARMV6(reg, sym)					\
+	"	.globl	" #sym "				\n\t"	\
+	"	.reloc	10f, R_ARM_ALU_PC_G0_NC, " #sym "	\n\t"	\
+	"	.reloc	11f, R_ARM_ALU_PC_G1_NC, " #sym "	\n\t"	\
+	"	.reloc	12f, R_ARM_LDR_PC_G2, " #sym "		\n\t"	\
+	"10:	sub	" #reg ", pc, #8			\n\t"	\
+	"11:	sub	" #reg ", " #reg ", #4			\n\t"	\
+	"12:	ldr	" #reg ", [" #reg ", #0]		\n\t"
+
 static inline unsigned long
 arm_gen_nop(void)
 {
diff --git a/arch/arm/include/asm/io.h b/arch/arm/include/asm/io.h
index c576fa7d9bf8..7fcdc785366c 100644
--- a/arch/arm/include/asm/io.h
+++ b/arch/arm/include/asm/io.h
@@ -139,11 +139,9 @@ extern void __iomem *__arm_ioremap_caller(phys_addr_t, size_t, unsigned int,
 extern void __iomem *__arm_ioremap_pfn(unsigned long, unsigned long, size_t, unsigned int);
 extern void __iomem *__arm_ioremap_exec(phys_addr_t, size_t, bool cached);
 void __arm_iomem_set_ro(void __iomem *ptr, size_t size);
-extern void __iounmap(volatile void __iomem *addr);
 
 extern void __iomem * (*arch_ioremap_caller)(phys_addr_t, size_t,
 	unsigned int, void *);
-extern void (*arch_iounmap)(volatile void __iomem *);
 
 /*
  * Bad read/write accesses...
@@ -174,13 +172,16 @@ static inline void __iomem *__typesafe_io(unsigned long addr)
 #define PCI_IO_VIRT_BASE	0xfee00000
 #define PCI_IOBASE		((void __iomem *)PCI_IO_VIRT_BASE)
 
-#if defined(CONFIG_PCI)
+#if defined(CONFIG_PCI) || IS_ENABLED(CONFIG_PCMCIA)
 void pci_ioremap_set_mem_type(int mem_type);
 #else
 static inline void pci_ioremap_set_mem_type(int mem_type) {}
 #endif
 
-extern int pci_ioremap_io(unsigned int offset, phys_addr_t phys_addr);
+struct resource;
+
+#define pci_remap_iospace pci_remap_iospace
+int pci_remap_iospace(const struct resource *res, phys_addr_t phys_addr);
 
 /*
  * PCI configuration space mapping function.
@@ -197,32 +198,13 @@ void __iomem *pci_remap_cfgspace(resource_size_t res_cookie, size_t size);
  */
 #ifdef CONFIG_NEED_MACH_IO_H
 #include <mach/io.h>
-#elif defined(CONFIG_PCI)
-#define IO_SPACE_LIMIT	((resource_size_t)0xfffff)
-#define __io(a)		__typesafe_io(PCI_IO_VIRT_BASE + ((a) & IO_SPACE_LIMIT))
 #else
-#define __io(a)		__typesafe_io((a) & IO_SPACE_LIMIT)
-#endif
-
-/*
- * This is the limit of PC card/PCI/ISA IO space, which is by default
- * 64K if we have PC card, PCI or ISA support.  Otherwise, default to
- * zero to prevent ISA/PCI drivers claiming IO space (and potentially
- * oopsing.)
- *
- * Only set this larger if you really need inb() et.al. to operate over
- * a larger address space.  Note that SOC_COMMON ioremaps each sockets
- * IO space area, and so inb() et.al. must be defined to operate as per
- * readb() et.al. on such platforms.
- */
-#ifndef IO_SPACE_LIMIT
-#if defined(CONFIG_PCMCIA_SOC_COMMON) || defined(CONFIG_PCMCIA_SOC_COMMON_MODULE)
-#define IO_SPACE_LIMIT ((resource_size_t)0xffffffff)
-#elif defined(CONFIG_PCI) || defined(CONFIG_ISA) || defined(CONFIG_PCCARD)
-#define IO_SPACE_LIMIT ((resource_size_t)0xffff)
+#if IS_ENABLED(CONFIG_PCMCIA) || defined(CONFIG_PCI)
+#define IO_SPACE_LIMIT	((resource_size_t)0xfffff)
 #else
 #define IO_SPACE_LIMIT ((resource_size_t)0)
 #endif
+#define __io(a)		__typesafe_io(PCI_IO_VIRT_BASE + ((a) & IO_SPACE_LIMIT))
 #endif
 
 /*
@@ -396,7 +378,7 @@ void __iomem *ioremap_wc(resource_size_t res_cookie, size_t size);
 #define ioremap_wc ioremap_wc
 #define ioremap_wt ioremap_wc
 
-void iounmap(volatile void __iomem *iomem_cookie);
+void iounmap(volatile void __iomem *io_addr);
 #define iounmap iounmap
 
 void *arch_memremap_wb(phys_addr_t phys_addr, size_t size);
@@ -437,6 +419,9 @@ extern void pci_iounmap(struct pci_dev *dev, void __iomem *addr);
 #define ARCH_HAS_VALID_PHYS_ADDR_RANGE
 extern int valid_phys_addr_range(phys_addr_t addr, size_t size);
 extern int valid_mmap_phys_addr_range(unsigned long pfn, size_t size);
+extern bool arch_memremap_can_ram_remap(resource_size_t offset, size_t size,
+					unsigned long flags);
+#define arch_memremap_can_ram_remap arch_memremap_can_ram_remap
 #endif
 
 /*
diff --git a/arch/arm/include/asm/irq.h b/arch/arm/include/asm/irq.h
index 1cbcc462b07e..a7c2337b0c7d 100644
--- a/arch/arm/include/asm/irq.h
+++ b/arch/arm/include/asm/irq.h
@@ -26,7 +26,6 @@
 struct irqaction;
 struct pt_regs;
 
-extern void asm_do_IRQ(unsigned int, struct pt_regs *);
 void handle_IRQ(unsigned int, struct pt_regs *);
 void init_IRQ(void);
 
diff --git a/arch/arm/include/asm/irq_work.h b/arch/arm/include/asm/irq_work.h
index 8895999834cc..3149e4dc1b54 100644
--- a/arch/arm/include/asm/irq_work.h
+++ b/arch/arm/include/asm/irq_work.h
@@ -9,4 +9,6 @@ static inline bool arch_irq_work_has_interrupt(void)
 	return is_smp();
 }
 
+extern void arch_irq_work_raise(void);
+
 #endif /* _ASM_ARM_IRQ_WORK_H */
diff --git a/arch/arm/include/asm/kfence.h b/arch/arm/include/asm/kfence.h
new file mode 100644
index 000000000000..7980d0f2271f
--- /dev/null
+++ b/arch/arm/include/asm/kfence.h
@@ -0,0 +1,53 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+
+#ifndef __ASM_ARM_KFENCE_H
+#define __ASM_ARM_KFENCE_H
+
+#include <linux/kfence.h>
+
+#include <asm/pgalloc.h>
+#include <asm/set_memory.h>
+
+static inline int split_pmd_page(pmd_t *pmd, unsigned long addr)
+{
+	int i;
+	unsigned long pfn = PFN_DOWN(__pa(addr));
+	pte_t *pte = pte_alloc_one_kernel(&init_mm);
+
+	if (!pte)
+		return -ENOMEM;
+
+	for (i = 0; i < PTRS_PER_PTE; i++)
+		set_pte_ext(pte + i, pfn_pte(pfn + i, PAGE_KERNEL), 0);
+	pmd_populate_kernel(&init_mm, pmd, pte);
+
+	flush_tlb_kernel_range(addr, addr + PMD_SIZE);
+	return 0;
+}
+
+static inline bool arch_kfence_init_pool(void)
+{
+	unsigned long addr;
+	pmd_t *pmd;
+
+	for (addr = (unsigned long)__kfence_pool; is_kfence_address((void *)addr);
+	     addr += PAGE_SIZE) {
+		pmd = pmd_off_k(addr);
+
+		if (pmd_leaf(*pmd)) {
+			if (split_pmd_page(pmd, addr & PMD_MASK))
+				return false;
+		}
+	}
+
+	return true;
+}
+
+static inline bool kfence_protect_page(unsigned long addr, bool protect)
+{
+	set_memory_valid(addr, 1, !protect);
+
+	return true;
+}
+
+#endif /* __ASM_ARM_KFENCE_H */
diff --git a/arch/arm/include/asm/mach/arch.h b/arch/arm/include/asm/mach/arch.h
index eec0c0bda766..9349e7a82c9c 100644
--- a/arch/arm/include/asm/mach/arch.h
+++ b/arch/arm/include/asm/mach/arch.h
@@ -56,9 +56,7 @@ struct machine_desc {
 	void			(*init_time)(void);
 	void			(*init_machine)(void);
 	void			(*init_late)(void);
-#ifdef CONFIG_GENERIC_IRQ_MULTI_HANDLER
 	void			(*handle_irq)(struct pt_regs *);
-#endif
 	void			(*restart)(enum reboot_mode, const char *);
 };
 
diff --git a/arch/arm/include/asm/mach/dma.h b/arch/arm/include/asm/mach/dma.h
index 1506422af383..5ec11d7f0d04 100644
--- a/arch/arm/include/asm/mach/dma.h
+++ b/arch/arm/include/asm/mach/dma.h
@@ -44,8 +44,3 @@ struct dma_struct {
  * isa_dma_add - add an ISA-style DMA channel
  */
 extern int isa_dma_add(unsigned int, dma_t *dma);
-
-/*
- * Add the ISA DMA controller.  Always takes channels 0-7.
- */
-extern void isa_init_dma(void);
diff --git a/arch/arm/include/asm/mach/map.h b/arch/arm/include/asm/mach/map.h
index 92282558caf7..2b8970d8e5a2 100644
--- a/arch/arm/include/asm/mach/map.h
+++ b/arch/arm/include/asm/mach/map.h
@@ -27,6 +27,7 @@ enum {
 	MT_HIGH_VECTORS,
 	MT_MEMORY_RWX,
 	MT_MEMORY_RW,
+	MT_MEMORY_RO,
 	MT_ROM,
 	MT_MEMORY_RWX_NONCACHED,
 	MT_MEMORY_RW_DTCM,
diff --git a/arch/arm/include/asm/memory.h b/arch/arm/include/asm/memory.h
index f673e13e0f94..d8eef4bd8c71 100644
--- a/arch/arm/include/asm/memory.h
+++ b/arch/arm/include/asm/memory.h
@@ -370,19 +370,6 @@ static inline unsigned long __virt_to_idmap(unsigned long x)
 #define virt_to_idmap(x)	__virt_to_idmap((unsigned long)(x))
 
 /*
- * Virtual <-> DMA view memory address translations
- * Again, these are *only* valid on the kernel direct mapped RAM
- * memory.  Use of these is *deprecated* (and that doesn't mean
- * use the __ prefixed forms instead.)  See dma-mapping.h.
- */
-#ifndef __virt_to_bus
-#define __virt_to_bus	__virt_to_phys
-#define __bus_to_virt	__phys_to_virt
-#define __pfn_to_bus(x)	__pfn_to_phys(x)
-#define __bus_to_pfn(x)	__phys_to_pfn(x)
-#endif
-
-/*
  * Conversion between a struct page and a physical address.
  *
  *  page_to_pfn(page)	convert a struct page * to a PFN number
diff --git a/arch/arm/include/asm/mmu.h b/arch/arm/include/asm/mmu.h
index 1592a4264488..e049723840d3 100644
--- a/arch/arm/include/asm/mmu.h
+++ b/arch/arm/include/asm/mmu.h
@@ -10,7 +10,7 @@ typedef struct {
 #else
 	int		switch_pending;
 #endif
-	unsigned int	vmalloc_seq;
+	atomic_t	vmalloc_seq;
 	unsigned long	sigpage;
 #ifdef CONFIG_VDSO
 	unsigned long	vdso;
diff --git a/arch/arm/include/asm/mmu_context.h b/arch/arm/include/asm/mmu_context.h
index 84e58956fcab..db2cb06aa8cf 100644
--- a/arch/arm/include/asm/mmu_context.h
+++ b/arch/arm/include/asm/mmu_context.h
@@ -23,6 +23,16 @@
 
 void __check_vmalloc_seq(struct mm_struct *mm);
 
+#ifdef CONFIG_MMU
+static inline void check_vmalloc_seq(struct mm_struct *mm)
+{
+	if (!IS_ENABLED(CONFIG_ARM_LPAE) &&
+	    unlikely(atomic_read(&mm->context.vmalloc_seq) !=
+		     atomic_read(&init_mm.context.vmalloc_seq)))
+		__check_vmalloc_seq(mm);
+}
+#endif
+
 #ifdef CONFIG_CPU_HAS_ASID
 
 void check_and_switch_context(struct mm_struct *mm, struct task_struct *tsk);
@@ -52,8 +62,7 @@ static inline void a15_erratum_get_cpumask(int this_cpu, struct mm_struct *mm,
 static inline void check_and_switch_context(struct mm_struct *mm,
 					    struct task_struct *tsk)
 {
-	if (unlikely(mm->context.vmalloc_seq != init_mm.context.vmalloc_seq))
-		__check_vmalloc_seq(mm);
+	check_vmalloc_seq(mm);
 
 	if (irqs_disabled())
 		/*
@@ -129,6 +138,15 @@ switch_mm(struct mm_struct *prev, struct mm_struct *next,
 #endif
 }
 
+#ifdef CONFIG_VMAP_STACK
+static inline void enter_lazy_tlb(struct mm_struct *mm, struct task_struct *tsk)
+{
+	if (mm != &init_mm)
+		check_vmalloc_seq(mm);
+}
+#define enter_lazy_tlb enter_lazy_tlb
+#endif
+
 #include <asm-generic/mmu_context.h>
 
 #endif
diff --git a/arch/arm/include/asm/module.h b/arch/arm/include/asm/module.h
index cfffae67c04e..5546c9751478 100644
--- a/arch/arm/include/asm/module.h
+++ b/arch/arm/include/asm/module.h
@@ -3,20 +3,10 @@
 #define _ASM_ARM_MODULE_H
 
 #include <asm-generic/module.h>
-
-struct unwind_table;
+#include <asm/unwind.h>
 
 #ifdef CONFIG_ARM_UNWIND
-enum {
-	ARM_SEC_INIT,
-	ARM_SEC_DEVINIT,
-	ARM_SEC_CORE,
-	ARM_SEC_EXIT,
-	ARM_SEC_DEVEXIT,
-	ARM_SEC_HOT,
-	ARM_SEC_UNLIKELY,
-	ARM_SEC_MAX,
-};
+#define ELF_SECTION_UNWIND 0x70000001
 #endif
 
 #define PLT_ENT_STRIDE		L1_CACHE_BYTES
@@ -36,7 +26,8 @@ struct mod_plt_sec {
 
 struct mod_arch_specific {
 #ifdef CONFIG_ARM_UNWIND
-	struct unwind_table *unwind[ARM_SEC_MAX];
+	struct list_head unwind_list;
+	struct unwind_table *init_table;
 #endif
 #ifdef CONFIG_ARM_MODULE_PLTS
 	struct mod_plt_sec	core;
diff --git a/arch/arm/include/asm/page.h b/arch/arm/include/asm/page.h
index 11b058a72a5b..5fcc8a600e36 100644
--- a/arch/arm/include/asm/page.h
+++ b/arch/arm/include/asm/page.h
@@ -147,6 +147,9 @@ extern void copy_page(void *to, const void *from);
 #include <asm/pgtable-3level-types.h>
 #else
 #include <asm/pgtable-2level-types.h>
+#ifdef CONFIG_VMAP_STACK
+#define ARCH_PAGE_TABLE_SYNC_MASK	PGTBL_PMD_MODIFIED
+#endif
 #endif
 
 #endif /* CONFIG_MMU */
diff --git a/arch/arm/include/asm/paravirt_api_clock.h b/arch/arm/include/asm/paravirt_api_clock.h
new file mode 100644
index 000000000000..65ac7cee0dad
--- /dev/null
+++ b/arch/arm/include/asm/paravirt_api_clock.h
@@ -0,0 +1 @@
+#include <asm/paravirt.h>
diff --git a/arch/arm/include/asm/pci.h b/arch/arm/include/asm/pci.h
index 68e6f25784a4..5916b88d4c94 100644
--- a/arch/arm/include/asm/pci.h
+++ b/arch/arm/include/asm/pci.h
@@ -22,11 +22,6 @@ static inline int pci_proc_domain(struct pci_bus *bus)
 #define HAVE_PCI_MMAP
 #define ARCH_GENERIC_PCI_MMAP_RESOURCE
 
-static inline int pci_get_legacy_ide_irq(struct pci_dev *dev, int channel)
-{
-	return channel ? 15 : 14;
-}
-
 extern void pcibios_report_status(unsigned int status_mask, int warn);
 
 #endif /* __KERNEL__ */
diff --git a/arch/arm/include/asm/percpu.h b/arch/arm/include/asm/percpu.h
index e2fcb3cfd3de..7545c87c251f 100644
--- a/arch/arm/include/asm/percpu.h
+++ b/arch/arm/include/asm/percpu.h
@@ -5,20 +5,27 @@
 #ifndef _ASM_ARM_PERCPU_H_
 #define _ASM_ARM_PERCPU_H_
 
+#include <asm/insn.h>
+
 register unsigned long current_stack_pointer asm ("sp");
 
 /*
  * Same as asm-generic/percpu.h, except that we store the per cpu offset
  * in the TPIDRPRW. TPIDRPRW only exists on V6K and V7
  */
-#if defined(CONFIG_SMP) && !defined(CONFIG_CPU_V6)
+#ifdef CONFIG_SMP
 static inline void set_my_cpu_offset(unsigned long off)
 {
+	extern unsigned int smp_on_up;
+
+	if (IS_ENABLED(CONFIG_CPU_V6) && !smp_on_up)
+		return;
+
 	/* Set TPIDRPRW */
 	asm volatile("mcr p15, 0, %0, c13, c0, 4" : : "r" (off) : "memory");
 }
 
-static inline unsigned long __my_cpu_offset(void)
+static __always_inline unsigned long __my_cpu_offset(void)
 {
 	unsigned long off;
 
@@ -27,8 +34,28 @@ static inline unsigned long __my_cpu_offset(void)
 	 * We want to allow caching the value, so avoid using volatile and
 	 * instead use a fake stack read to hazard against barrier().
 	 */
-	asm("mrc p15, 0, %0, c13, c0, 4" : "=r" (off)
-		: "Q" (*(const unsigned long *)current_stack_pointer));
+	asm("0:	mrc p15, 0, %0, c13, c0, 4			\n\t"
+#ifdef CONFIG_CPU_V6
+	    "1:							\n\t"
+	    "	.subsection 1					\n\t"
+#if defined(CONFIG_ARM_HAS_GROUP_RELOCS) && \
+    !(defined(MODULE) && defined(CONFIG_ARM_MODULE_PLTS))
+	    "2: " LOAD_SYM_ARMV6(%0, __per_cpu_offset) "	\n\t"
+	    "	b	1b					\n\t"
+#else
+	    "2: ldr	%0, 3f					\n\t"
+	    "	ldr	%0, [%0]				\n\t"
+	    "	b	1b					\n\t"
+	    "3:	.long	__per_cpu_offset			\n\t"
+#endif
+	    "	.previous					\n\t"
+	    "	.pushsection \".alt.smp.init\", \"a\"		\n\t"
+	    "	.long	0b - .					\n\t"
+	    "	b	. + (2b - 0b)				\n\t"
+	    "	.popsection					\n\t"
+#endif
+	     : "=r" (off)
+	     : "Q" (*(const unsigned long *)current_stack_pointer));
 
 	return off;
 }
diff --git a/arch/arm/include/asm/pgtable-2level.h b/arch/arm/include/asm/pgtable-2level.h
index 70fe69bdcce2..92abd4cd8ca2 100644
--- a/arch/arm/include/asm/pgtable-2level.h
+++ b/arch/arm/include/asm/pgtable-2level.h
@@ -208,6 +208,8 @@ static inline pmd_t *pmd_offset(pud_t *pud, unsigned long addr)
 }
 #define pmd_offset pmd_offset
 
+#define pmd_pfn(pmd)		(__phys_to_pfn(pmd_val(pmd) & PHYS_MASK))
+
 #define pmd_large(pmd)		(pmd_val(pmd) & 2)
 #define pmd_leaf(pmd)		(pmd_val(pmd) & 2)
 #define pmd_bad(pmd)		(pmd_val(pmd) & 2)
diff --git a/arch/arm/include/asm/pgtable.h b/arch/arm/include/asm/pgtable.h
index cd1f84bb40ae..78a532068fec 100644
--- a/arch/arm/include/asm/pgtable.h
+++ b/arch/arm/include/asm/pgtable.h
@@ -137,23 +137,6 @@ extern pgprot_t phys_mem_access_prot(struct file *file, unsigned long pfn,
  *  2) If we could do execute protection, then read is implied
  *  3) write implies read permissions
  */
-#define __P000  __PAGE_NONE
-#define __P001  __PAGE_READONLY
-#define __P010  __PAGE_COPY
-#define __P011  __PAGE_COPY
-#define __P100  __PAGE_READONLY_EXEC
-#define __P101  __PAGE_READONLY_EXEC
-#define __P110  __PAGE_COPY_EXEC
-#define __P111  __PAGE_COPY_EXEC
-
-#define __S000  __PAGE_NONE
-#define __S001  __PAGE_READONLY
-#define __S010  __PAGE_SHARED
-#define __S011  __PAGE_SHARED
-#define __S100  __PAGE_READONLY_EXEC
-#define __S101  __PAGE_READONLY_EXEC
-#define __S110  __PAGE_SHARED_EXEC
-#define __S111  __PAGE_SHARED_EXEC
 
 #ifndef __ASSEMBLY__
 /*
diff --git a/arch/arm/include/asm/processor.h b/arch/arm/include/asm/processor.h
index 6af68edfa53a..326864f79d18 100644
--- a/arch/arm/include/asm/processor.h
+++ b/arch/arm/include/asm/processor.h
@@ -81,9 +81,6 @@ static inline void arch_thread_struct_whitelist(unsigned long *offset,
 /* Forward declaration, a strange C thing */
 struct task_struct;
 
-/* Free all resources held by a thread. */
-extern void release_thread(struct task_struct *);
-
 unsigned long __get_wchan(struct task_struct *p);
 
 #define task_pt_regs(p) \
@@ -96,6 +93,7 @@ unsigned long __get_wchan(struct task_struct *p);
 #define __ALT_SMP_ASM(smp, up)						\
 	"9998:	" smp "\n"						\
 	"	.pushsection \".alt.smp.init\", \"a\"\n"		\
+	"	.align	2\n"						\
 	"	.long	9998b - .\n"					\
 	"	" up "\n"						\
 	"	.popsection\n"
diff --git a/arch/arm/include/asm/ptrace.h b/arch/arm/include/asm/ptrace.h
index 93051e2f402c..1408a6a15d0e 100644
--- a/arch/arm/include/asm/ptrace.h
+++ b/arch/arm/include/asm/ptrace.h
@@ -163,5 +163,31 @@ static inline unsigned long user_stack_pointer(struct pt_regs *regs)
 		((current_stack_pointer | (THREAD_SIZE - 1)) - 7) - 1;	\
 })
 
+
+/*
+ * Update ITSTATE after normal execution of an IT block instruction.
+ *
+ * The 8 IT state bits are split into two parts in CPSR:
+ *	ITSTATE<1:0> are in CPSR<26:25>
+ *	ITSTATE<7:2> are in CPSR<15:10>
+ */
+static inline unsigned long it_advance(unsigned long cpsr)
+{
+	if ((cpsr & 0x06000400) == 0) {
+		/* ITSTATE<2:0> == 0 means end of IT block, so clear IT state */
+		cpsr &= ~PSR_IT_MASK;
+	} else {
+		/* We need to shift left ITSTATE<4:0> */
+		const unsigned long mask = 0x06001c00;  /* Mask ITSTATE<4:0> */
+		unsigned long it = cpsr & mask;
+		it <<= 1;
+		it |= it >> (27 - 10);  /* Carry ITSTATE<2> to correct place */
+		it &= mask;
+		cpsr &= ~mask;
+		cpsr |= it;
+	}
+	return cpsr;
+}
+
 #endif /* __ASSEMBLY__ */
 #endif
diff --git a/arch/arm/include/asm/set_memory.h b/arch/arm/include/asm/set_memory.h
index ec17fc0fda7a..0211b9c5b14d 100644
--- a/arch/arm/include/asm/set_memory.h
+++ b/arch/arm/include/asm/set_memory.h
@@ -11,6 +11,7 @@ int set_memory_ro(unsigned long addr, int numpages);
 int set_memory_rw(unsigned long addr, int numpages);
 int set_memory_x(unsigned long addr, int numpages);
 int set_memory_nx(unsigned long addr, int numpages);
+int set_memory_valid(unsigned long addr, int numpages, int enable);
 #else
 static inline int set_memory_ro(unsigned long addr, int numpages) { return 0; }
 static inline int set_memory_rw(unsigned long addr, int numpages) { return 0; }
diff --git a/arch/arm/include/asm/smp.h b/arch/arm/include/asm/smp.h
index f16cbbd5cda4..7c1c90d9f582 100644
--- a/arch/arm/include/asm/smp.h
+++ b/arch/arm/include/asm/smp.h
@@ -25,11 +25,6 @@ struct seq_file;
 extern void show_ipi_list(struct seq_file *, int);
 
 /*
- * Called from assembly code, this handles an IPI.
- */
-asmlinkage void do_IPI(int ipinr, struct pt_regs *regs);
-
-/*
  * Called from C code, this handles an IPI.
  */
 void handle_IPI(int ipinr, struct pt_regs *regs);
diff --git a/arch/arm/include/asm/spectre.h b/arch/arm/include/asm/spectre.h
new file mode 100644
index 000000000000..85f9e538fb32
--- /dev/null
+++ b/arch/arm/include/asm/spectre.h
@@ -0,0 +1,38 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+
+#ifndef __ASM_SPECTRE_H
+#define __ASM_SPECTRE_H
+
+enum {
+	SPECTRE_UNAFFECTED,
+	SPECTRE_MITIGATED,
+	SPECTRE_VULNERABLE,
+};
+
+enum {
+	__SPECTRE_V2_METHOD_BPIALL,
+	__SPECTRE_V2_METHOD_ICIALLU,
+	__SPECTRE_V2_METHOD_SMC,
+	__SPECTRE_V2_METHOD_HVC,
+	__SPECTRE_V2_METHOD_LOOP8,
+};
+
+enum {
+	SPECTRE_V2_METHOD_BPIALL = BIT(__SPECTRE_V2_METHOD_BPIALL),
+	SPECTRE_V2_METHOD_ICIALLU = BIT(__SPECTRE_V2_METHOD_ICIALLU),
+	SPECTRE_V2_METHOD_SMC = BIT(__SPECTRE_V2_METHOD_SMC),
+	SPECTRE_V2_METHOD_HVC = BIT(__SPECTRE_V2_METHOD_HVC),
+	SPECTRE_V2_METHOD_LOOP8 = BIT(__SPECTRE_V2_METHOD_LOOP8),
+};
+
+#ifdef CONFIG_GENERIC_CPU_VULNERABILITIES
+void spectre_v2_update_state(unsigned int state, unsigned int methods);
+#else
+static inline void spectre_v2_update_state(unsigned int state,
+					   unsigned int methods)
+{}
+#endif
+
+int spectre_bhb_update_vectors(unsigned int method);
+
+#endif
diff --git a/arch/arm/include/asm/stacktrace.h b/arch/arm/include/asm/stacktrace.h
index 8f54f9ad8a9b..36b2ff44fcbb 100644
--- a/arch/arm/include/asm/stacktrace.h
+++ b/arch/arm/include/asm/stacktrace.h
@@ -14,10 +14,16 @@ struct stackframe {
 	unsigned long sp;
 	unsigned long lr;
 	unsigned long pc;
+
+	/* address of the LR value on the stack */
+	unsigned long *lr_addr;
 #ifdef CONFIG_KRETPROBES
 	struct llist_node *kr_cur;
 	struct task_struct *tsk;
 #endif
+#ifdef CONFIG_UNWINDER_FRAME_POINTER
+	bool ex_frame;
+#endif
 };
 
 static __always_inline
@@ -31,10 +37,17 @@ void arm_get_current_stackframe(struct pt_regs *regs, struct stackframe *frame)
 		frame->kr_cur = NULL;
 		frame->tsk = current;
 #endif
+#ifdef CONFIG_UNWINDER_FRAME_POINTER
+		frame->ex_frame = in_entry_text(frame->pc);
+#endif
 }
 
 extern int unwind_frame(struct stackframe *frame);
 extern void walk_stackframe(struct stackframe *frame,
 			    int (*fn)(struct stackframe *, void *), void *data);
+extern void dump_mem(const char *lvl, const char *str, unsigned long bottom,
+		     unsigned long top);
+extern void dump_backtrace(struct pt_regs *regs, struct task_struct *tsk,
+			   const char *loglvl);
 
 #endif	/* __ASM_STACKTRACE_H */
diff --git a/arch/arm/include/asm/switch_to.h b/arch/arm/include/asm/switch_to.h
index b55c7b2755e4..9372348516ce 100644
--- a/arch/arm/include/asm/switch_to.h
+++ b/arch/arm/include/asm/switch_to.h
@@ -3,6 +3,7 @@
 #define __ASM_ARM_SWITCH_TO_H
 
 #include <linux/thread_info.h>
+#include <asm/smp_plat.h>
 
 /*
  * For v7 SMP cores running a preemptible kernel we may be pre-empted
@@ -23,24 +24,10 @@
  */
 extern struct task_struct *__switch_to(struct task_struct *, struct thread_info *, struct thread_info *);
 
-static inline void set_ti_cpu(struct task_struct *p)
-{
-#ifdef CONFIG_THREAD_INFO_IN_TASK
-	/*
-	 * The core code no longer maintains the thread_info::cpu field once
-	 * CONFIG_THREAD_INFO_IN_TASK is in effect, but we rely on it for
-	 * raw_smp_processor_id(), which cannot access struct task_struct*
-	 * directly for reasons of circular #inclusion hell.
-	 */
-	task_thread_info(p)->cpu = task_cpu(p);
-#endif
-}
-
 #define switch_to(prev,next,last)					\
 do {									\
 	__complete_pending_tlbi();					\
-	set_ti_cpu(next);						\
-	if (IS_ENABLED(CONFIG_CURRENT_POINTER_IN_TPIDRURO))		\
+	if (IS_ENABLED(CONFIG_CURRENT_POINTER_IN_TPIDRURO) || is_smp())	\
 		__this_cpu_write(__entry_task, next);			\
 	last = __switch_to(prev,task_thread_info(prev), task_thread_info(next));	\
 } while (0)
diff --git a/arch/arm/include/asm/thread_info.h b/arch/arm/include/asm/thread_info.h
index 164e15f26485..aecc403b2880 100644
--- a/arch/arm/include/asm/thread_info.h
+++ b/arch/arm/include/asm/thread_info.h
@@ -25,6 +25,14 @@
 #define THREAD_SIZE		(PAGE_SIZE << THREAD_SIZE_ORDER)
 #define THREAD_START_SP		(THREAD_SIZE - 8)
 
+#ifdef CONFIG_VMAP_STACK
+#define THREAD_ALIGN		(2 * THREAD_SIZE)
+#else
+#define THREAD_ALIGN		THREAD_SIZE
+#endif
+
+#define OVERFLOW_STACK_SIZE	SZ_4K
+
 #ifndef __ASSEMBLY__
 
 struct task_struct;
@@ -54,9 +62,6 @@ struct cpu_context_save {
 struct thread_info {
 	unsigned long		flags;		/* low level flags */
 	int			preempt_count;	/* 0 => preemptable, <0 => bug */
-#ifndef CONFIG_THREAD_INFO_IN_TASK
-	struct task_struct	*task;		/* main task structure */
-#endif
 	__u32			cpu;		/* cpu */
 	__u32			cpu_domain;	/* cpu domain */
 	struct cpu_context_save	cpu_context;	/* cpu context */
@@ -72,39 +77,15 @@ struct thread_info {
 
 #define INIT_THREAD_INFO(tsk)						\
 {									\
-	INIT_THREAD_INFO_TASK(tsk)					\
 	.flags		= 0,						\
 	.preempt_count	= INIT_PREEMPT_COUNT,				\
 }
 
-#ifdef CONFIG_THREAD_INFO_IN_TASK
-#define INIT_THREAD_INFO_TASK(tsk)
-
 static inline struct task_struct *thread_task(struct thread_info* ti)
 {
 	return (struct task_struct *)ti;
 }
 
-#else
-#define INIT_THREAD_INFO_TASK(tsk)	.task = &(tsk),
-
-static inline struct task_struct *thread_task(struct thread_info* ti)
-{
-	return ti->task;
-}
-
-/*
- * how to get the thread information struct from C
- */
-static inline struct thread_info *current_thread_info(void) __attribute_const__;
-
-static inline struct thread_info *current_thread_info(void)
-{
-	return (struct thread_info *)
-		(current_stack_pointer & ~(THREAD_SIZE - 1));
-}
-#endif
-
 #define thread_saved_pc(tsk)	\
 	((unsigned long)(task_thread_info(tsk)->cpu_context.pc))
 #define thread_saved_sp(tsk)	\
diff --git a/arch/arm/include/asm/timex.h b/arch/arm/include/asm/timex.h
index 7c3b3671d6c2..6d1337c169cd 100644
--- a/arch/arm/include/asm/timex.h
+++ b/arch/arm/include/asm/timex.h
@@ -11,5 +11,6 @@
 
 typedef unsigned long cycles_t;
 #define get_cycles()	({ cycles_t c; read_current_timer(&c) ? 0 : c; })
+#define random_get_entropy() (((unsigned long)get_cycles()) ?: random_get_entropy_fallback())
 
 #endif
diff --git a/arch/arm/include/asm/tls.h b/arch/arm/include/asm/tls.h
index c3296499176c..3dcd0f71a0da 100644
--- a/arch/arm/include/asm/tls.h
+++ b/arch/arm/include/asm/tls.h
@@ -18,21 +18,32 @@
 	.endm
 
 	.macro switch_tls_v6, base, tp, tpuser, tmp1, tmp2
-	ldr	\tmp1, =elf_hwcap
-	ldr	\tmp1, [\tmp1, #0]
+#ifdef CONFIG_SMP
+ALT_SMP(nop)
+ALT_UP_B(.L0_\@)
+	.subsection 1
+#endif
+.L0_\@:
+	ldr_va	\tmp1, elf_hwcap
 	mov	\tmp2, #0xffff0fff
 	tst	\tmp1, #HWCAP_TLS		@ hardware TLS available?
 	streq	\tp, [\tmp2, #-15]		@ set TLS value at 0xffff0ff0
-	mrcne	p15, 0, \tmp2, c13, c0, 2	@ get the user r/w register
-	mcrne	p15, 0, \tp, c13, c0, 3		@ yes, set TLS register
-	mcrne	p15, 0, \tpuser, c13, c0, 2	@ set user r/w register
-	strne	\tmp2, [\base, #TI_TP_VALUE + 4] @ save it
+	beq	.L2_\@
+	mcr	p15, 0, \tp, c13, c0, 3		@ yes, set TLS register
+#ifdef CONFIG_SMP
+	b	.L1_\@
+	.previous
+#endif
+.L1_\@: switch_tls_v6k \base, \tp, \tpuser, \tmp1, \tmp2
+.L2_\@:
 	.endm
 
 	.macro switch_tls_software, base, tp, tpuser, tmp1, tmp2
 	mov	\tmp1, #0xffff0fff
 	str	\tp, [\tmp1, #-15]		@ set TLS value at 0xffff0ff0
 	.endm
+#else
+#include <asm/smp_plat.h>
 #endif
 
 #ifdef CONFIG_TLS_REG_EMUL
@@ -43,7 +54,7 @@
 #elif defined(CONFIG_CPU_V6)
 #define tls_emu		0
 #define has_tls_reg		(elf_hwcap & HWCAP_TLS)
-#define defer_tls_reg_update	0
+#define defer_tls_reg_update	is_smp()
 #define switch_tls	switch_tls_v6
 #elif defined(CONFIG_CPU_32v6K)
 #define tls_emu		0
@@ -81,11 +92,11 @@ static inline void set_tls(unsigned long val)
 	 */
 	barrier();
 
-	if (!tls_emu && !defer_tls_reg_update) {
-		if (has_tls_reg) {
+	if (!tls_emu) {
+		if (has_tls_reg && !defer_tls_reg_update) {
 			asm("mcr p15, 0, %0, c13, c0, 3"
 			    : : "r" (val));
-		} else {
+		} else if (!has_tls_reg) {
 #ifdef CONFIG_KUSER_HELPERS
 			/*
 			 * User space must never try to access this
diff --git a/arch/arm/include/asm/topology.h b/arch/arm/include/asm/topology.h
index 470299ee2fba..c7d2510e5a78 100644
--- a/arch/arm/include/asm/topology.h
+++ b/arch/arm/include/asm/topology.h
@@ -23,7 +23,7 @@
 
 /* Replace task scheduler's default thermal pressure API */
 #define arch_scale_thermal_pressure topology_get_thermal_pressure
-#define arch_set_thermal_pressure   topology_set_thermal_pressure
+#define arch_update_thermal_pressure	topology_update_thermal_pressure
 
 #else
 
diff --git a/arch/arm/include/asm/uaccess.h b/arch/arm/include/asm/uaccess.h
index 36fbc3329252..2fcbec9c306c 100644
--- a/arch/arm/include/asm/uaccess.h
+++ b/arch/arm/include/asm/uaccess.h
@@ -11,6 +11,7 @@
 #include <linux/string.h>
 #include <asm/memory.h>
 #include <asm/domain.h>
+#include <asm/unaligned.h>
 #include <asm/unified.h>
 #include <asm/compiler.h>
 
@@ -55,21 +56,6 @@ extern int __put_user_bad(void);
 #ifdef CONFIG_MMU
 
 /*
- * We use 33-bit arithmetic here.  Success returns zero, failure returns
- * addr_limit.  We take advantage that addr_limit will be zero for KERNEL_DS,
- * so this will always return success in that case.
- */
-#define __range_ok(addr, size) ({ \
-	unsigned long flag, roksum; \
-	__chk_user_ptr(addr);	\
-	__asm__(".syntax unified\n" \
-		"adds %1, %2, %3; sbcscc %1, %1, %0; movcc %0, #0" \
-		: "=&r" (flag), "=&r" (roksum) \
-		: "r" (addr), "Ir" (size), "0" (TASK_SIZE) \
-		: "cc"); \
-	flag; })
-
-/*
  * This is a type: either unsigned long, if the argument fits into
  * that type, or otherwise unsigned long long.
  */
@@ -240,15 +226,12 @@ extern int __put_user_8(void *, unsigned long long);
 
 #else /* CONFIG_MMU */
 
-#define __addr_ok(addr)		((void)(addr), 1)
-#define __range_ok(addr, size)	((void)(addr), 0)
-
 #define get_user(x, p)	__get_user(x, p)
 #define __put_user_check __put_user_nocheck
 
 #endif /* CONFIG_MMU */
 
-#define access_ok(addr, size)	(__range_ok(addr, size) == 0)
+#include <asm-generic/access_ok.h>
 
 #ifdef CONFIG_CPU_SPECTRE
 /*
@@ -475,8 +458,6 @@ do {									\
 	: "r" (x), "i" (-EFAULT)				\
 	: "cc")
 
-#define HAVE_GET_KERNEL_NOFAULT
-
 #define __get_kernel_nofault(dst, src, type, err_label)			\
 do {									\
 	const type *__pk_ptr = (src);					\
@@ -497,7 +478,10 @@ do {									\
 	}								\
 	default: __err = __get_user_bad(); break;			\
 	}								\
-	*(type *)(dst) = __val;						\
+	if (IS_ENABLED(CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS))		\
+		put_unaligned(__val, (type *)(dst));			\
+	else								\
+		*(type *)(dst) = __val; /* aligned by caller */		\
 	if (__err)							\
 		goto err_label;						\
 } while (0)
@@ -507,7 +491,9 @@ do {									\
 	const type *__pk_ptr = (dst);					\
 	unsigned long __dst = (unsigned long)__pk_ptr;			\
 	int __err = 0;							\
-	type __val = *(type *)src;					\
+	type __val = IS_ENABLED(CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS)	\
+		     ? get_unaligned((type *)(src))			\
+		     : *(type *)(src);	/* aligned by caller */		\
 	switch (sizeof(type)) {						\
 	case 1: __put_user_asm_byte(__val, __dst, __err, ""); break;	\
 	case 2:	__put_user_asm_half(__val, __dst, __err, ""); break;	\
diff --git a/arch/arm/include/asm/unwind.h b/arch/arm/include/asm/unwind.h
index 0f8a3439902d..b51f85417f58 100644
--- a/arch/arm/include/asm/unwind.h
+++ b/arch/arm/include/asm/unwind.h
@@ -24,6 +24,7 @@ struct unwind_idx {
 
 struct unwind_table {
 	struct list_head list;
+	struct list_head mod_list;
 	const struct unwind_idx *start;
 	const struct unwind_idx *origin;
 	const struct unwind_idx *stop;
diff --git a/arch/arm/include/asm/user.h b/arch/arm/include/asm/user.h
index c799a3c49342..167d44b550f4 100644
--- a/arch/arm/include/asm/user.h
+++ b/arch/arm/include/asm/user.h
@@ -77,10 +77,6 @@ struct user{
   struct user_fp_struct * u_fp0;/* Used by gdb to help find the values for */
   				/* the FP registers. */
 };
-#define NBPG PAGE_SIZE
-#define UPAGES 1
-#define HOST_TEXT_START_ADDR (u.start_code)
-#define HOST_STACK_END_ADDR (u.start_stack + u.u_ssize * NBPG)
 
 /*
  * User specific VFP registers. If only VFPv2 is present, registers 16 to 31
diff --git a/arch/arm/include/asm/v7m.h b/arch/arm/include/asm/v7m.h
index 2cb00d15831b..4512f7e1918f 100644
--- a/arch/arm/include/asm/v7m.h
+++ b/arch/arm/include/asm/v7m.h
@@ -13,6 +13,7 @@
 #define V7M_SCB_ICSR_PENDSVSET			(1 << 28)
 #define V7M_SCB_ICSR_PENDSVCLR			(1 << 27)
 #define V7M_SCB_ICSR_RETTOBASE			(1 << 11)
+#define V7M_SCB_ICSR_VECTACTIVE			0x000001ff
 
 #define V7M_SCB_VTOR			0x08
 
@@ -38,7 +39,7 @@
 #define V7M_SCB_SHCSR_MEMFAULTENA		(1 << 16)
 
 #define V7M_xPSR_FRAMEPTRALIGN			0x00000200
-#define V7M_xPSR_EXCEPTIONNO			0x000001ff
+#define V7M_xPSR_EXCEPTIONNO			V7M_SCB_ICSR_VECTACTIVE
 
 /*
  * When branching to an address that has bits [31:28] == 0xf an exception return
diff --git a/arch/arm/include/asm/vmlinux.lds.h b/arch/arm/include/asm/vmlinux.lds.h
index 4a91428c324d..fad45c884e98 100644
--- a/arch/arm/include/asm/vmlinux.lds.h
+++ b/arch/arm/include/asm/vmlinux.lds.h
@@ -26,6 +26,19 @@
 #define ARM_MMU_DISCARD(x)	x
 #endif
 
+/*
+ * ld.lld does not support NOCROSSREFS:
+ * https://github.com/ClangBuiltLinux/linux/issues/1609
+ */
+#ifdef CONFIG_LD_IS_LLD
+#define NOCROSSREFS
+#endif
+
+/* Set start/end symbol names to the LMA for the section */
+#define ARM_LMA(sym, section)						\
+	sym##_start = LOADADDR(section);				\
+	sym##_end = LOADADDR(section) + SIZEOF(section)
+
 #define PROC_INFO							\
 		. = ALIGN(4);						\
 		__proc_info_begin = .;					\
@@ -110,19 +123,31 @@
  * only thing that matters is their relative offsets
  */
 #define ARM_VECTORS							\
-	__vectors_start = .;						\
-	.vectors 0xffff0000 : AT(__vectors_start) {			\
-		*(.vectors)						\
+	__vectors_lma = .;						\
+	OVERLAY 0xffff0000 : NOCROSSREFS AT(__vectors_lma) {		\
+		.vectors {						\
+			*(.vectors)					\
+		}							\
+		.vectors.bhb.loop8 {					\
+			*(.vectors.bhb.loop8)				\
+		}							\
+		.vectors.bhb.bpiall {					\
+			*(.vectors.bhb.bpiall)				\
+		}							\
 	}								\
-	. = __vectors_start + SIZEOF(.vectors);				\
-	__vectors_end = .;						\
+	ARM_LMA(__vectors, .vectors);					\
+	ARM_LMA(__vectors_bhb_loop8, .vectors.bhb.loop8);		\
+	ARM_LMA(__vectors_bhb_bpiall, .vectors.bhb.bpiall);		\
+	. = __vectors_lma + SIZEOF(.vectors) +				\
+		SIZEOF(.vectors.bhb.loop8) +				\
+		SIZEOF(.vectors.bhb.bpiall);				\
 									\
-	__stubs_start = .;						\
-	.stubs ADDR(.vectors) + 0x1000 : AT(__stubs_start) {		\
+	__stubs_lma = .;						\
+	.stubs ADDR(.vectors) + 0x1000 : AT(__stubs_lma) {		\
 		*(.stubs)						\
 	}								\
-	. = __stubs_start + SIZEOF(.stubs);				\
-	__stubs_end = .;						\
+	ARM_LMA(__stubs, .stubs);					\
+	. = __stubs_lma + SIZEOF(.stubs);				\
 									\
 	PROVIDE(vector_fiq_offset = vector_fiq - ADDR(.vectors));
 
diff --git a/arch/arm/include/asm/xen/page-coherent.h b/arch/arm/include/asm/xen/page-coherent.h
deleted file mode 100644
index 27e984977402..000000000000
--- a/arch/arm/include/asm/xen/page-coherent.h
+++ /dev/null
@@ -1,2 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-#include <xen/arm/page-coherent.h>
diff --git a/arch/arm/include/asm/xen/xen-ops.h b/arch/arm/include/asm/xen/xen-ops.h
new file mode 100644
index 000000000000..7ebb7eb0bd93
--- /dev/null
+++ b/arch/arm/include/asm/xen/xen-ops.h
@@ -0,0 +1,2 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#include <xen/arm/xen-ops.h>
diff --git a/arch/arm/include/asm/xor.h b/arch/arm/include/asm/xor.h
index aefddec79286..669cad5194d3 100644
--- a/arch/arm/include/asm/xor.h
+++ b/arch/arm/include/asm/xor.h
@@ -44,7 +44,8 @@
 		: "0" (dst), "r" (a1), "r" (a2), "r" (a3), "r" (a4))
 
 static void
-xor_arm4regs_2(unsigned long bytes, unsigned long *p1, unsigned long *p2)
+xor_arm4regs_2(unsigned long bytes, unsigned long * __restrict p1,
+	       const unsigned long * __restrict p2)
 {
 	unsigned int lines = bytes / sizeof(unsigned long) / 4;
 	register unsigned int a1 __asm__("r4");
@@ -64,8 +65,9 @@ xor_arm4regs_2(unsigned long bytes, unsigned long *p1, unsigned long *p2)
 }
 
 static void
-xor_arm4regs_3(unsigned long bytes, unsigned long *p1, unsigned long *p2,
-		unsigned long *p3)
+xor_arm4regs_3(unsigned long bytes, unsigned long * __restrict p1,
+	       const unsigned long * __restrict p2,
+	       const unsigned long * __restrict p3)
 {
 	unsigned int lines = bytes / sizeof(unsigned long) / 4;
 	register unsigned int a1 __asm__("r4");
@@ -86,8 +88,10 @@ xor_arm4regs_3(unsigned long bytes, unsigned long *p1, unsigned long *p2,
 }
 
 static void
-xor_arm4regs_4(unsigned long bytes, unsigned long *p1, unsigned long *p2,
-		unsigned long *p3, unsigned long *p4)
+xor_arm4regs_4(unsigned long bytes, unsigned long * __restrict p1,
+	       const unsigned long * __restrict p2,
+	       const unsigned long * __restrict p3,
+	       const unsigned long * __restrict p4)
 {
 	unsigned int lines = bytes / sizeof(unsigned long) / 2;
 	register unsigned int a1 __asm__("r8");
@@ -105,8 +109,11 @@ xor_arm4regs_4(unsigned long bytes, unsigned long *p1, unsigned long *p2,
 }
 
 static void
-xor_arm4regs_5(unsigned long bytes, unsigned long *p1, unsigned long *p2,
-		unsigned long *p3, unsigned long *p4, unsigned long *p5)
+xor_arm4regs_5(unsigned long bytes, unsigned long * __restrict p1,
+	       const unsigned long * __restrict p2,
+	       const unsigned long * __restrict p3,
+	       const unsigned long * __restrict p4,
+	       const unsigned long * __restrict p5)
 {
 	unsigned int lines = bytes / sizeof(unsigned long) / 2;
 	register unsigned int a1 __asm__("r8");
@@ -146,7 +153,8 @@ static struct xor_block_template xor_block_arm4regs = {
 extern struct xor_block_template const xor_block_neon_inner;
 
 static void
-xor_neon_2(unsigned long bytes, unsigned long *p1, unsigned long *p2)
+xor_neon_2(unsigned long bytes, unsigned long * __restrict p1,
+	   const unsigned long * __restrict p2)
 {
 	if (in_interrupt()) {
 		xor_arm4regs_2(bytes, p1, p2);
@@ -158,8 +166,9 @@ xor_neon_2(unsigned long bytes, unsigned long *p1, unsigned long *p2)
 }
 
 static void
-xor_neon_3(unsigned long bytes, unsigned long *p1, unsigned long *p2,
-		unsigned long *p3)
+xor_neon_3(unsigned long bytes, unsigned long * __restrict p1,
+	   const unsigned long * __restrict p2,
+	   const unsigned long * __restrict p3)
 {
 	if (in_interrupt()) {
 		xor_arm4regs_3(bytes, p1, p2, p3);
@@ -171,8 +180,10 @@ xor_neon_3(unsigned long bytes, unsigned long *p1, unsigned long *p2,
 }
 
 static void
-xor_neon_4(unsigned long bytes, unsigned long *p1, unsigned long *p2,
-		unsigned long *p3, unsigned long *p4)
+xor_neon_4(unsigned long bytes, unsigned long * __restrict p1,
+	   const unsigned long * __restrict p2,
+	   const unsigned long * __restrict p3,
+	   const unsigned long * __restrict p4)
 {
 	if (in_interrupt()) {
 		xor_arm4regs_4(bytes, p1, p2, p3, p4);
@@ -184,8 +195,11 @@ xor_neon_4(unsigned long bytes, unsigned long *p1, unsigned long *p2,
 }
 
 static void
-xor_neon_5(unsigned long bytes, unsigned long *p1, unsigned long *p2,
-		unsigned long *p3, unsigned long *p4, unsigned long *p5)
+xor_neon_5(unsigned long bytes, unsigned long * __restrict p1,
+	   const unsigned long * __restrict p2,
+	   const unsigned long * __restrict p3,
+	   const unsigned long * __restrict p4,
+	   const unsigned long * __restrict p5)
 {
 	if (in_interrupt()) {
 		xor_arm4regs_5(bytes, p1, p2, p3, p4, p5);
diff --git a/arch/arm/include/debug/brcmstb.S b/arch/arm/include/debug/brcmstb.S
index f684e3a815f6..f6175e6e28cd 100644
--- a/arch/arm/include/debug/brcmstb.S
+++ b/arch/arm/include/debug/brcmstb.S
@@ -1,15 +1,5 @@
-/*
- * Copyright (C) 2016 Broadcom
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation version 2.
- *
- * This program is distributed "as is" WITHOUT ANY WARRANTY of any
- * kind, whether express or implied; without even the implied warranty
- * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- */
+/* SPDX-License-Identifier: GPL-2.0-only */
+/* Copyright (C) 2016 Broadcom */
 #include <linux/serial_reg.h>
 #include <asm/cputype.h>
 
diff --git a/arch/arm/include/debug/imx-uart.h b/arch/arm/include/debug/imx-uart.h
index c8eb83d4b896..3edbb3c5b42b 100644
--- a/arch/arm/include/debug/imx-uart.h
+++ b/arch/arm/include/debug/imx-uart.h
@@ -11,13 +11,6 @@
 #define IMX1_UART_BASE_ADDR(n)	IMX1_UART##n##_BASE_ADDR
 #define IMX1_UART_BASE(n)	IMX1_UART_BASE_ADDR(n)
 
-#define IMX21_UART1_BASE_ADDR	0x1000a000
-#define IMX21_UART2_BASE_ADDR	0x1000b000
-#define IMX21_UART3_BASE_ADDR	0x1000c000
-#define IMX21_UART4_BASE_ADDR	0x1000d000
-#define IMX21_UART_BASE_ADDR(n)	IMX21_UART##n##_BASE_ADDR
-#define IMX21_UART_BASE(n)	IMX21_UART_BASE_ADDR(n)
-
 #define IMX25_UART1_BASE_ADDR	0x43f90000
 #define IMX25_UART2_BASE_ADDR	0x43f94000
 #define IMX25_UART3_BASE_ADDR	0x5000c000
@@ -26,6 +19,13 @@
 #define IMX25_UART_BASE_ADDR(n)	IMX25_UART##n##_BASE_ADDR
 #define IMX25_UART_BASE(n)	IMX25_UART_BASE_ADDR(n)
 
+#define IMX27_UART1_BASE_ADDR	0x1000a000
+#define IMX27_UART2_BASE_ADDR	0x1000b000
+#define IMX27_UART3_BASE_ADDR	0x1000c000
+#define IMX27_UART4_BASE_ADDR	0x1000d000
+#define IMX27_UART_BASE_ADDR(n)	IMX27_UART##n##_BASE_ADDR
+#define IMX27_UART_BASE(n)	IMX27_UART_BASE_ADDR(n)
+
 #define IMX31_UART1_BASE_ADDR	0x43f90000
 #define IMX31_UART2_BASE_ADDR	0x43f94000
 #define IMX31_UART3_BASE_ADDR	0x5000c000
@@ -112,10 +112,10 @@
 
 #ifdef CONFIG_DEBUG_IMX1_UART
 #define UART_PADDR	IMX_DEBUG_UART_BASE(IMX1)
-#elif defined(CONFIG_DEBUG_IMX21_IMX27_UART)
-#define UART_PADDR	IMX_DEBUG_UART_BASE(IMX21)
 #elif defined(CONFIG_DEBUG_IMX25_UART)
 #define UART_PADDR	IMX_DEBUG_UART_BASE(IMX25)
+#elif defined(CONFIG_DEBUG_IMX27_UART)
+#define UART_PADDR	IMX_DEBUG_UART_BASE(IMX27)
 #elif defined(CONFIG_DEBUG_IMX31_UART)
 #define UART_PADDR	IMX_DEBUG_UART_BASE(IMX31)
 #elif defined(CONFIG_DEBUG_IMX35_UART)
diff --git a/arch/arm/include/debug/pl01x.S b/arch/arm/include/debug/pl01x.S
index 0c7bfa4c10db..c7e02d0628bf 100644
--- a/arch/arm/include/debug/pl01x.S
+++ b/arch/arm/include/debug/pl01x.S
@@ -8,13 +8,6 @@
 */
 #include <linux/amba/serial.h>
 
-#ifdef CONFIG_DEBUG_ZTE_ZX
-#undef UART01x_DR
-#undef UART01x_FR
-#define UART01x_DR     0x04
-#define UART01x_FR     0x14
-#endif
-
 #ifdef CONFIG_DEBUG_UART_PHYS
 		.macro	addruart, rp, rv, tmp
 		ldr	\rp, =CONFIG_DEBUG_UART_PHYS
diff --git a/arch/arm/include/uapi/asm/signal.h b/arch/arm/include/uapi/asm/signal.h
index c9a3ea1d8d41..9e2178420db2 100644
--- a/arch/arm/include/uapi/asm/signal.h
+++ b/arch/arm/include/uapi/asm/signal.h
@@ -93,7 +93,7 @@ struct sigaction {
 typedef struct sigaltstack {
 	void __user *ss_sp;
 	int ss_flags;
-	size_t ss_size;
+	__kernel_size_t ss_size;
 } stack_t;
 
 
diff --git a/arch/arm/kernel/Makefile b/arch/arm/kernel/Makefile
index ae295a3bcfef..48737ec800eb 100644
--- a/arch/arm/kernel/Makefile
+++ b/arch/arm/kernel/Makefile
@@ -10,6 +10,7 @@ ifdef CONFIG_FUNCTION_TRACER
 CFLAGS_REMOVE_ftrace.o = -pg
 CFLAGS_REMOVE_insn.o = -pg
 CFLAGS_REMOVE_patch.o = -pg
+CFLAGS_REMOVE_unwind.o = -pg
 endif
 
 CFLAGS_REMOVE_return_address.o = -pg
@@ -44,7 +45,6 @@ obj-$(CONFIG_ISA_DMA_API)	+= dma.o
 obj-$(CONFIG_FIQ)		+= fiq.o fiqasm.o
 obj-$(CONFIG_MODULES)		+= armksyms.o module.o
 obj-$(CONFIG_ARM_MODULE_PLTS)	+= module-plts.o
-obj-$(CONFIG_ISA_DMA)		+= dma-isa.o
 obj-$(CONFIG_PCI)		+= bios32.o isa.o
 obj-$(CONFIG_ARM_CPU_SUSPEND)	+= sleep.o suspend.o
 obj-$(CONFIG_HIBERNATION)	+= hibernate.o
@@ -88,7 +88,7 @@ obj-$(CONFIG_VDSO)		+= vdso.o
 obj-$(CONFIG_EFI)		+= efi.o
 obj-$(CONFIG_PARAVIRT)	+= paravirt.o
 
-head-y			:= head$(MMUEXT).o
+obj-y			+= head$(MMUEXT).o
 obj-$(CONFIG_DEBUG_LL)	+= debug.o
 obj-$(CONFIG_EARLY_PRINTK)	+= early_printk.o
 obj-$(CONFIG_ARM_PATCH_PHYS_VIRT)	+= phys2virt.o
@@ -106,4 +106,6 @@ endif
 
 obj-$(CONFIG_HAVE_ARM_SMCCC)	+= smccc-call.o
 
-extra-y := $(head-y) vmlinux.lds
+obj-$(CONFIG_GENERIC_CPU_VULNERABILITIES) += spectre.o
+
+extra-y := vmlinux.lds
diff --git a/arch/arm/kernel/asm-offsets.c b/arch/arm/kernel/asm-offsets.c
index 645845e4982a..2c8d76fd7c66 100644
--- a/arch/arm/kernel/asm-offsets.c
+++ b/arch/arm/kernel/asm-offsets.c
@@ -43,9 +43,6 @@ int main(void)
   BLANK();
   DEFINE(TI_FLAGS,		offsetof(struct thread_info, flags));
   DEFINE(TI_PREEMPT,		offsetof(struct thread_info, preempt_count));
-#ifndef CONFIG_THREAD_INFO_IN_TASK
-  DEFINE(TI_TASK,		offsetof(struct thread_info, task));
-#endif
   DEFINE(TI_CPU,		offsetof(struct thread_info, cpu));
   DEFINE(TI_CPU_DOMAIN,		offsetof(struct thread_info, cpu_domain));
   DEFINE(TI_CPU_SAVE,		offsetof(struct thread_info, cpu_context));
diff --git a/arch/arm/kernel/atags_proc.c b/arch/arm/kernel/atags_proc.c
index 3c2faf2bd124..3ec2afe78423 100644
--- a/arch/arm/kernel/atags_proc.c
+++ b/arch/arm/kernel/atags_proc.c
@@ -13,7 +13,7 @@ struct buffer {
 static ssize_t atags_read(struct file *file, char __user *buf,
 			  size_t count, loff_t *ppos)
 {
-	struct buffer *b = PDE_DATA(file_inode(file));
+	struct buffer *b = pde_data(file_inode(file));
 	return simple_read_from_buffer(buf, count, ppos, b->data, b->size);
 }
 
diff --git a/arch/arm/kernel/crash_dump.c b/arch/arm/kernel/crash_dump.c
index 53cb92435392..938bd932df9a 100644
--- a/arch/arm/kernel/crash_dump.c
+++ b/arch/arm/kernel/crash_dump.c
@@ -14,22 +14,10 @@
 #include <linux/crash_dump.h>
 #include <linux/uaccess.h>
 #include <linux/io.h>
+#include <linux/uio.h>
 
-/**
- * copy_oldmem_page() - copy one page from old kernel memory
- * @pfn: page frame number to be copied
- * @buf: buffer where the copied page is placed
- * @csize: number of bytes to copy
- * @offset: offset in bytes into the page
- * @userbuf: if set, @buf is int he user address space
- *
- * This function copies one page from old kernel memory into buffer pointed by
- * @buf. If @buf is in userspace, set @userbuf to %1. Returns number of bytes
- * copied or negative error in case of failure.
- */
-ssize_t copy_oldmem_page(unsigned long pfn, char *buf,
-			 size_t csize, unsigned long offset,
-			 int userbuf)
+ssize_t copy_oldmem_page(struct iov_iter *iter, unsigned long pfn,
+			 size_t csize, unsigned long offset)
 {
 	void *vaddr;
 
@@ -40,14 +28,7 @@ ssize_t copy_oldmem_page(unsigned long pfn, char *buf,
 	if (!vaddr)
 		return -ENOMEM;
 
-	if (userbuf) {
-		if (copy_to_user(buf, vaddr + offset, csize)) {
-			iounmap(vaddr);
-			return -EFAULT;
-		}
-	} else {
-		memcpy(buf, vaddr + offset, csize);
-	}
+	csize = copy_to_iter(vaddr + offset, csize, iter);
 
 	iounmap(vaddr);
 	return csize;
diff --git a/arch/arm/kernel/devtree.c b/arch/arm/kernel/devtree.c
index 02839d8b6202..264827281113 100644
--- a/arch/arm/kernel/devtree.c
+++ b/arch/arm/kernel/devtree.c
@@ -194,14 +194,12 @@ const struct machine_desc * __init setup_machine_fdt(void *dt_virt)
 {
 	const struct machine_desc *mdesc, *mdesc_best = NULL;
 
-#if defined(CONFIG_ARCH_MULTIPLATFORM) || defined(CONFIG_ARM_SINGLE_ARMV7M)
 	DT_MACHINE_START(GENERIC_DT, "Generic DT based system")
 		.l2c_aux_val = 0x0,
 		.l2c_aux_mask = ~0x0,
 	MACHINE_END
 
 	mdesc_best = &__mach_desc_GENERIC_DT;
-#endif
 
 	if (!dt_virt || !early_init_dt_verify(dt_virt))
 		return NULL;
diff --git a/arch/arm/kernel/efi.c b/arch/arm/kernel/efi.c
index e57dbcc89123..e50ad7eefc02 100644
--- a/arch/arm/kernel/efi.c
+++ b/arch/arm/kernel/efi.c
@@ -4,6 +4,7 @@
  */
 
 #include <linux/efi.h>
+#include <linux/memblock.h>
 #include <asm/efi.h>
 #include <asm/mach/map.h>
 #include <asm/mmu_context.h>
@@ -73,3 +74,81 @@ int __init efi_create_mapping(struct mm_struct *mm, efi_memory_desc_t *md)
 		return efi_set_mapping_permissions(mm, md);
 	return 0;
 }
+
+static unsigned long __initdata screen_info_table = EFI_INVALID_TABLE_ADDR;
+static unsigned long __initdata cpu_state_table = EFI_INVALID_TABLE_ADDR;
+
+const efi_config_table_type_t efi_arch_tables[] __initconst = {
+	{LINUX_EFI_ARM_SCREEN_INFO_TABLE_GUID, &screen_info_table},
+	{LINUX_EFI_ARM_CPU_STATE_TABLE_GUID, &cpu_state_table},
+	{}
+};
+
+static void __init load_screen_info_table(void)
+{
+	struct screen_info *si;
+
+	if (screen_info_table != EFI_INVALID_TABLE_ADDR) {
+		si = early_memremap_ro(screen_info_table, sizeof(*si));
+		if (!si) {
+			pr_err("Could not map screen_info config table\n");
+			return;
+		}
+		screen_info = *si;
+		early_memunmap(si, sizeof(*si));
+
+		/* dummycon on ARM needs non-zero values for columns/lines */
+		screen_info.orig_video_cols = 80;
+		screen_info.orig_video_lines = 25;
+
+		if (memblock_is_map_memory(screen_info.lfb_base))
+			memblock_mark_nomap(screen_info.lfb_base,
+					    screen_info.lfb_size);
+	}
+}
+
+static void __init load_cpu_state_table(void)
+{
+	if (cpu_state_table != EFI_INVALID_TABLE_ADDR) {
+		struct efi_arm_entry_state *state;
+		bool dump_state = true;
+
+		state = early_memremap_ro(cpu_state_table,
+					  sizeof(struct efi_arm_entry_state));
+		if (state == NULL) {
+			pr_warn("Unable to map CPU entry state table.\n");
+			return;
+		}
+
+		if ((state->sctlr_before_ebs & 1) == 0)
+			pr_warn(FW_BUG "EFI stub was entered with MMU and Dcache disabled, please fix your firmware!\n");
+		else if ((state->sctlr_after_ebs & 1) == 0)
+			pr_warn(FW_BUG "ExitBootServices() returned with MMU and Dcache disabled, please fix your firmware!\n");
+		else
+			dump_state = false;
+
+		if (dump_state || efi_enabled(EFI_DBG)) {
+			pr_info("CPSR at EFI stub entry        : 0x%08x\n",
+				state->cpsr_before_ebs);
+			pr_info("SCTLR at EFI stub entry       : 0x%08x\n",
+				state->sctlr_before_ebs);
+			pr_info("CPSR after ExitBootServices() : 0x%08x\n",
+				state->cpsr_after_ebs);
+			pr_info("SCTLR after ExitBootServices(): 0x%08x\n",
+				state->sctlr_after_ebs);
+		}
+		early_memunmap(state, sizeof(struct efi_arm_entry_state));
+	}
+}
+
+void __init arm_efi_init(void)
+{
+	efi_init();
+
+	load_screen_info_table();
+
+	/* ARM does not permit early mappings to persist across paging_init() */
+	efi_memmap_unmap();
+
+	load_cpu_state_table();
+}
diff --git a/arch/arm/kernel/entry-armv.S b/arch/arm/kernel/entry-armv.S
index deff286eb5ea..c39303e5c234 100644
--- a/arch/arm/kernel/entry-armv.S
+++ b/arch/arm/kernel/entry-armv.S
@@ -19,9 +19,6 @@
 #include <asm/glue-df.h>
 #include <asm/glue-pf.h>
 #include <asm/vfpmacros.h>
-#ifndef CONFIG_GENERIC_IRQ_MULTI_HANDLER
-#include <mach/entry-macro.S>
-#endif
 #include <asm/thread_notify.h>
 #include <asm/unwind.h>
 #include <asm/unistd.h>
@@ -30,27 +27,42 @@
 #include <asm/uaccess-asm.h>
 
 #include "entry-header.S"
-#include <asm/entry-macro-multi.S>
 #include <asm/probes.h>
 
 /*
  * Interrupt handling.
  */
-	.macro	irq_handler
-#ifdef CONFIG_GENERIC_IRQ_MULTI_HANDLER
-	mov	r0, sp
-	bl	generic_handle_arch_irq
-#else
-	arch_irq_handler_default
+	.macro	irq_handler, from_user:req
+	mov	r1, sp
+	ldr_this_cpu r2, irq_stack_ptr, r2, r3
+	.if	\from_user == 0
+	@
+	@ If we took the interrupt while running in the kernel, we may already
+	@ be using the IRQ stack, so revert to the original value in that case.
+	@
+	subs	r3, r2, r1		@ SP above bottom of IRQ stack?
+	rsbscs	r3, r3, #THREAD_SIZE	@ ... and below the top?
+#ifdef CONFIG_VMAP_STACK
+	ldr_va	r3, high_memory, cc	@ End of the linear region
+	cmpcc	r3, r1			@ Stack pointer was below it?
 #endif
+	bcc	0f			@ If not, switch to the IRQ stack
+	mov	r0, r1
+	bl	generic_handle_arch_irq
+	b	1f
+0:
+	.endif
+
+	mov_l	r0, generic_handle_arch_irq
+	bl	call_with_stack
+1:
 	.endm
 
 	.macro	pabt_helper
 	@ PABORT handler takes pt_regs in r2, fault address in r4 and psr in r5
 #ifdef MULTI_PABORT
-	ldr	ip, .LCprocfns
-	mov	lr, pc
-	ldr	pc, [ip, #PROCESSOR_PABT_FUNC]
+	ldr_va	ip, processor, offset=PROCESSOR_PABT_FUNC
+	bl_r	ip
 #else
 	bl	CPU_PABORT_HANDLER
 #endif
@@ -69,9 +81,8 @@
 	@ the fault status register in r1.  r9 must be preserved.
 	@
 #ifdef MULTI_DABORT
-	ldr	ip, .LCprocfns
-	mov	lr, pc
-	ldr	pc, [ip, #PROCESSOR_DABT_FUNC]
+	ldr_va	ip, processor, offset=PROCESSOR_DABT_FUNC
+	bl_r	ip
 #else
 	bl	CPU_DABORT_HANDLER
 #endif
@@ -140,27 +151,35 @@ ENDPROC(__und_invalid)
 #define SPFIX(code...)
 #endif
 
-	.macro	svc_entry, stack_hole=0, trace=1, uaccess=1
+	.macro	svc_entry, stack_hole=0, trace=1, uaccess=1, overflow_check=1
  UNWIND(.fnstart		)
- UNWIND(.save {r0 - pc}		)
-	sub	sp, sp, #(SVC_REGS_SIZE + \stack_hole - 4)
+	sub	sp, sp, #(SVC_REGS_SIZE + \stack_hole)
+ THUMB(	add	sp, r1		)	@ get SP in a GPR without
+ THUMB(	sub	r1, sp, r1	)	@ using a temp register
+
+	.if	\overflow_check
+ UNWIND(.save	{r0 - pc}	)
+	do_overflow_check (SVC_REGS_SIZE + \stack_hole)
+	.endif
+
 #ifdef CONFIG_THUMB2_KERNEL
- SPFIX(	str	r0, [sp]	)	@ temporarily saved
- SPFIX(	mov	r0, sp		)
- SPFIX(	tst	r0, #4		)	@ test original stack alignment
- SPFIX(	ldr	r0, [sp]	)	@ restored
+	tst	r1, #4			@ test stack pointer alignment
+	sub	r1, sp, r1		@ restore original R1
+	sub	sp, r1			@ restore original SP
 #else
  SPFIX(	tst	sp, #4		)
 #endif
- SPFIX(	subeq	sp, sp, #4	)
-	stmia	sp, {r1 - r12}
+ SPFIX(	subne	sp, sp, #4	)
+
+ ARM(	stmib	sp, {r1 - r12}	)
+ THUMB(	stmia	sp, {r0 - r12}	)	@ No STMIB in Thumb-2
 
 	ldmia	r0, {r3 - r5}
-	add	r7, sp, #S_SP - 4	@ here for interlock avoidance
+	add	r7, sp, #S_SP		@ here for interlock avoidance
 	mov	r6, #-1			@  ""  ""      ""       ""
-	add	r2, sp, #(SVC_REGS_SIZE + \stack_hole - 4)
- SPFIX(	addeq	r2, r2, #4	)
-	str	r3, [sp, #-4]!		@ save the "real" r0 copied
+	add	r2, sp, #(SVC_REGS_SIZE + \stack_hole)
+ SPFIX(	addne	r2, r2, #4	)
+	str	r3, [sp]		@ save the "real" r0 copied
 					@ from the exception stack
 
 	mov	r3, lr
@@ -199,7 +218,7 @@ ENDPROC(__dabt_svc)
 	.align	5
 __irq_svc:
 	svc_entry
-	irq_handler
+	irq_handler from_user=0
 
 #ifdef CONFIG_PREEMPTION
 	ldr	r8, [tsk, #TI_PREEMPT]		@ get preempt count
@@ -281,16 +300,6 @@ __fiq_svc:
  UNWIND(.fnend		)
 ENDPROC(__fiq_svc)
 
-	.align	5
-.LCcralign:
-	.word	cr_alignment
-#ifdef MULTI_DABORT
-.LCprocfns:
-	.word	processor
-#endif
-.LCfp:
-	.word	fp_enter
-
 /*
  * Abort mode handlers
  */
@@ -349,7 +358,7 @@ ENDPROC(__fiq_abt)
  THUMB(	stmia	sp, {r0 - r12}	)
 
  ATRAP(	mrc	p15, 0, r7, c1, c0, 0)
- ATRAP(	ldr	r8, .LCcralign)
+ ATRAP(	ldr_va	r8, cr_alignment)
 
 	ldmia	r0, {r3 - r5}
 	add	r0, sp, #S_PC		@ here for interlock avoidance
@@ -358,8 +367,6 @@ ENDPROC(__fiq_abt)
 	str	r3, [sp]		@ save the "real" r0 copied
 					@ from the exception stack
 
- ATRAP(	ldr	r8, [r8, #0])
-
 	@
 	@ We are now ready to fill in the remaining blanks on the stack:
 	@
@@ -426,7 +433,7 @@ ENDPROC(__dabt_usr)
 __irq_usr:
 	usr_entry
 	kuser_cmpxchg_check
-	irq_handler
+	irq_handler from_user=1
 	get_thread_info tsk
 	mov	why, #0
 	b	ret_to_user_from_irq
@@ -484,9 +491,7 @@ __und_usr_thumb:
  */
 #if __LINUX_ARM_ARCH__ < 7
 /* If the target CPU may not be Thumb-2-capable, a run-time check is needed: */
-#define NEED_CPU_ARCHITECTURE
-	ldr	r5, .LCcpu_architecture
-	ldr	r5, [r5]
+	ldr_va	r5, cpu_architecture
 	cmp	r5, #CPU_ARCH_ARMv7
 	blo	__und_usr_fault_16		@ 16bit undefined instruction
 /*
@@ -596,11 +601,9 @@ call_fpe:
 	tstne	r0, #0x04000000			@ bit 26 set on both ARM and Thumb-2
 	reteq	lr
 	and	r8, r0, #0x00000f00		@ mask out CP number
- THUMB(	lsr	r8, r8, #8		)
 	mov	r7, #1
-	add	r6, r10, #TI_USED_CP
- ARM(	strb	r7, [r6, r8, lsr #8]	)	@ set appropriate used_cp[]
- THUMB(	strb	r7, [r6, r8]		)	@ set appropriate used_cp[]
+	add	r6, r10, r8, lsr #8		@ add used_cp[] array offset first
+	strb	r7, [r6, #TI_USED_CP]		@ set appropriate used_cp[]
 #ifdef CONFIG_IWMMXT
 	@ Test if we need to give access to iWMMXt coprocessors
 	ldr	r5, [r10, #TI_FLAGS]
@@ -609,7 +612,7 @@ call_fpe:
 	bcs	iwmmxt_task_enable
 #endif
  ARM(	add	pc, pc, r8, lsr #6	)
- THUMB(	lsl	r8, r8, #2		)
+ THUMB(	lsr	r8, r8, #6		)
  THUMB(	add	pc, r8			)
 	nop
 
@@ -635,12 +638,6 @@ call_fpe:
 	ret.w	lr				@ CP#14 (Debug)
 	ret.w	lr				@ CP#15 (Control)
 
-#ifdef NEED_CPU_ARCHITECTURE
-	.align	2
-.LCcpu_architecture:
-	.word	__cpu_architecture
-#endif
-
 #ifdef CONFIG_NEON
 	.align	6
 
@@ -666,9 +663,8 @@ call_fpe:
 #endif
 
 do_fpe:
-	ldr	r4, .LCfp
 	add	r10, r10, #TI_FPSTATE		@ r10 = workspace
-	ldr	pc, [r4]			@ Call FP module USR entry point
+	ldr_va	pc, fp_enter, tmp=r4		@ Call FP module USR entry point
 
 /*
  * The FP module is called with these registers set:
@@ -754,16 +750,17 @@ ENTRY(__switch_to)
 	ldr	r6, [r2, #TI_CPU_DOMAIN]
 #endif
 	switch_tls r1, r4, r5, r3, r7
-#if defined(CONFIG_STACKPROTECTOR) && !defined(CONFIG_SMP)
-	ldr	r7, [r2, #TI_TASK]
+#if defined(CONFIG_STACKPROTECTOR) && !defined(CONFIG_SMP) && \
+    !defined(CONFIG_STACKPROTECTOR_PER_TASK)
 	ldr	r8, =__stack_chk_guard
 	.if (TSK_STACK_CANARY > IMM12_MASK)
-	add	r7, r7, #TSK_STACK_CANARY & ~IMM12_MASK
+	add	r9, r2, #TSK_STACK_CANARY & ~IMM12_MASK
+	ldr	r9, [r9, #TSK_STACK_CANARY & IMM12_MASK]
+	.else
+	ldr	r9, [r2, #TSK_STACK_CANARY & IMM12_MASK]
 	.endif
-	ldr	r7, [r7, #TSK_STACK_CANARY & IMM12_MASK]
-#elif defined(CONFIG_CURRENT_POINTER_IN_TPIDRURO)
-	mov	r7, r2				@ Preserve 'next'
 #endif
+	mov	r7, r2				@ Preserve 'next'
 #ifdef CONFIG_CPU_USE_DOMAINS
 	mcr	p15, 0, r6, c3, c0, 0		@ Set domain register
 #endif
@@ -772,19 +769,102 @@ ENTRY(__switch_to)
 	ldr	r0, =thread_notify_head
 	mov	r1, #THREAD_NOTIFY_SWITCH
 	bl	atomic_notifier_call_chain
-#if defined(CONFIG_STACKPROTECTOR) && !defined(CONFIG_SMP)
-	str	r7, [r8]
+#if defined(CONFIG_STACKPROTECTOR) && !defined(CONFIG_SMP) && \
+    !defined(CONFIG_STACKPROTECTOR_PER_TASK)
+	str	r9, [r8]
 #endif
- THUMB(	mov	ip, r4			   )
 	mov	r0, r5
-	set_current r7
- ARM(	ldmia	r4, {r4 - sl, fp, sp, pc}  )	@ Load all regs saved previously
- THUMB(	ldmia	ip!, {r4 - sl, fp}	   )	@ Load all regs saved previously
- THUMB(	ldr	sp, [ip], #4		   )
- THUMB(	ldr	pc, [ip]		   )
+#if !defined(CONFIG_THUMB2_KERNEL) && !defined(CONFIG_VMAP_STACK)
+	set_current r7, r8
+	ldmia	r4, {r4 - sl, fp, sp, pc}	@ Load all regs saved previously
+#else
+	mov	r1, r7
+	ldmia	r4, {r4 - sl, fp, ip, lr}	@ Load all regs saved previously
+#ifdef CONFIG_VMAP_STACK
+	@
+	@ Do a dummy read from the new stack while running from the old one so
+	@ that we can rely on do_translation_fault() to fix up any stale PMD
+	@ entries covering the vmalloc region.
+	@
+	ldr	r2, [ip]
+#endif
+
+	@ When CONFIG_THREAD_INFO_IN_TASK=n, the update of SP itself is what
+	@ effectuates the task switch, as that is what causes the observable
+	@ values of current and current_thread_info to change. When
+	@ CONFIG_THREAD_INFO_IN_TASK=y, setting current (and therefore
+	@ current_thread_info) is done explicitly, and the update of SP just
+	@ switches us to another stack, with few other side effects. In order
+	@ to prevent this distinction from causing any inconsistencies, let's
+	@ keep the 'set_current' call as close as we can to the update of SP.
+	set_current r1, r2
+	mov	sp, ip
+	ret	lr
+#endif
  UNWIND(.fnend		)
 ENDPROC(__switch_to)
 
+#ifdef CONFIG_VMAP_STACK
+	.text
+	.align	2
+__bad_stack:
+	@
+	@ We've just detected an overflow. We need to load the address of this
+	@ CPU's overflow stack into the stack pointer register. We have only one
+	@ scratch register so let's use a sequence of ADDs including one
+	@ involving the PC, and decorate them with PC-relative group
+	@ relocations. As these are ARM only, switch to ARM mode first.
+	@
+	@ We enter here with IP clobbered and its value stashed on the mode
+	@ stack.
+	@
+THUMB(	bx	pc		)
+THUMB(	nop			)
+THUMB(	.arm			)
+	ldr_this_cpu_armv6 ip, overflow_stack_ptr
+
+	str	sp, [ip, #-4]!			@ Preserve original SP value
+	mov	sp, ip				@ Switch to overflow stack
+	pop	{ip}				@ Original SP in IP
+
+#if defined(CONFIG_UNWINDER_FRAME_POINTER) && defined(CONFIG_CC_IS_GCC)
+	mov	ip, ip				@ mov expected by unwinder
+	push	{fp, ip, lr, pc}		@ GCC flavor frame record
+#else
+	str	ip, [sp, #-8]!			@ store original SP
+	push	{fpreg, lr}			@ Clang flavor frame record
+#endif
+UNWIND( ldr	ip, [r0, #4]	)		@ load exception LR
+UNWIND( str	ip, [sp, #12]	)		@ store in the frame record
+	ldr	ip, [r0, #12]			@ reload IP
+
+	@ Store the original GPRs to the new stack.
+	svc_entry uaccess=0, overflow_check=0
+
+UNWIND( .save   {sp, pc}	)
+UNWIND( .save   {fpreg, lr}	)
+UNWIND( .setfp  fpreg, sp	)
+
+	ldr	fpreg, [sp, #S_SP]		@ Add our frame record
+						@ to the linked list
+#if defined(CONFIG_UNWINDER_FRAME_POINTER) && defined(CONFIG_CC_IS_GCC)
+	ldr	r1, [fp, #4]			@ reload SP at entry
+	add	fp, fp, #12
+#else
+	ldr	r1, [fpreg, #8]
+#endif
+	str	r1, [sp, #S_SP]			@ store in pt_regs
+
+	@ Stash the regs for handle_bad_stack
+	mov	r0, sp
+
+	@ Time to die
+	bl	handle_bad_stack
+	nop
+UNWIND( .fnend			)
+ENDPROC(__bad_stack)
+#endif
+
 	__INIT
 
 /*
@@ -998,17 +1078,23 @@ __kuser_helper_end:
  */
 	.macro	vector_stub, name, mode, correction=0
 	.align	5
+#ifdef CONFIG_HARDEN_BRANCH_HISTORY
+vector_bhb_bpiall_\name:
+	mcr	p15, 0, r0, c7, c5, 6	@ BPIALL
+	@ isb not needed due to "movs pc, lr" in the vector stub
+	@ which gives a "context synchronisation".
+#endif
 
 vector_\name:
 	.if \correction
 	sub	lr, lr, #\correction
 	.endif
 
-	@
-	@ Save r0, lr_<exception> (parent PC) and spsr_<exception>
-	@ (parent CPSR)
-	@
+	@ Save r0, lr_<exception> (parent PC)
 	stmia	sp, {r0, lr}		@ save r0, lr
+
+	@ Save spsr_<exception> (parent CPSR)
+.Lvec_\name:
 	mrs	lr, spsr
 	str	lr, [sp, #8]		@ save spsr
 
@@ -1030,14 +1116,47 @@ vector_\name:
 	movs	pc, lr			@ branch to handler in SVC mode
 ENDPROC(vector_\name)
 
+#ifdef CONFIG_HARDEN_BRANCH_HISTORY
+	.subsection 1
+	.align 5
+vector_bhb_loop8_\name:
+	.if \correction
+	sub	lr, lr, #\correction
+	.endif
+
+	@ Save r0, lr_<exception> (parent PC)
+	stmia	sp, {r0, lr}
+
+	@ bhb workaround
+	mov	r0, #8
+3:	W(b)	. + 4
+	subs	r0, r0, #1
+	bne	3b
+	dsb	nsh
+	@ isb not needed due to "movs pc, lr" in the vector stub
+	@ which gives a "context synchronisation".
+	b	.Lvec_\name
+ENDPROC(vector_bhb_loop8_\name)
+	.previous
+#endif
+
 	.align	2
 	@ handler addresses follow this label
 1:
 	.endm
 
 	.section .stubs, "ax", %progbits
-	@ This must be the first word
+	@ These need to remain at the start of the section so that
+	@ they are in range of the 'SWI' entries in the vector tables
+	@ located 4k down.
+.L__vector_swi:
 	.word	vector_swi
+#ifdef CONFIG_HARDEN_BRANCH_HISTORY
+.L__vector_bhb_loop8_swi:
+	.word	vector_bhb_loop8_swi
+.L__vector_bhb_bpiall_swi:
+	.word	vector_bhb_bpiall_swi
+#endif
 
 vector_rst:
  ARM(	swi	SYS_ERROR0	)
@@ -1152,8 +1271,10 @@ vector_addrexcptn:
  * FIQ "NMI" handler
  *-----------------------------------------------------------------------------
  * Handle a FIQ using the SVC stack allowing FIQ act like NMI on x86
- * systems.
+ * systems. This must be the last vector stub, so lets place it in its own
+ * subsection.
  */
+	.subsection 2
 	vector_stub	fiq, FIQ_MODE, 4
 
 	.long	__fiq_usr			@  0  (USR_26 / USR_32)
@@ -1176,16 +1297,43 @@ vector_addrexcptn:
 	.globl	vector_fiq
 
 	.section .vectors, "ax", %progbits
-.L__vectors_start:
 	W(b)	vector_rst
 	W(b)	vector_und
-	W(ldr)	pc, .L__vectors_start + 0x1000
+ARM(	.reloc	., R_ARM_LDR_PC_G0, .L__vector_swi		)
+THUMB(	.reloc	., R_ARM_THM_PC12, .L__vector_swi		)
+	W(ldr)	pc, .
 	W(b)	vector_pabt
 	W(b)	vector_dabt
 	W(b)	vector_addrexcptn
 	W(b)	vector_irq
 	W(b)	vector_fiq
 
+#ifdef CONFIG_HARDEN_BRANCH_HISTORY
+	.section .vectors.bhb.loop8, "ax", %progbits
+	W(b)	vector_rst
+	W(b)	vector_bhb_loop8_und
+ARM(	.reloc	., R_ARM_LDR_PC_G0, .L__vector_bhb_loop8_swi	)
+THUMB(	.reloc	., R_ARM_THM_PC12, .L__vector_bhb_loop8_swi	)
+	W(ldr)	pc, .
+	W(b)	vector_bhb_loop8_pabt
+	W(b)	vector_bhb_loop8_dabt
+	W(b)	vector_addrexcptn
+	W(b)	vector_bhb_loop8_irq
+	W(b)	vector_bhb_loop8_fiq
+
+	.section .vectors.bhb.bpiall, "ax", %progbits
+	W(b)	vector_rst
+	W(b)	vector_bhb_bpiall_und
+ARM(	.reloc	., R_ARM_LDR_PC_G0, .L__vector_bhb_bpiall_swi	)
+THUMB(	.reloc	., R_ARM_THM_PC12, .L__vector_bhb_bpiall_swi	)
+	W(ldr)	pc, .
+	W(b)	vector_bhb_bpiall_pabt
+	W(b)	vector_bhb_bpiall_dabt
+	W(b)	vector_addrexcptn
+	W(b)	vector_bhb_bpiall_irq
+	W(b)	vector_bhb_bpiall_fiq
+#endif
+
 	.data
 	.align	2
 
diff --git a/arch/arm/kernel/entry-common.S b/arch/arm/kernel/entry-common.S
index ac86c34682bb..405a607b754f 100644
--- a/arch/arm/kernel/entry-common.S
+++ b/arch/arm/kernel/entry-common.S
@@ -16,17 +16,19 @@
 
 	.equ	NR_syscalls, __NR_syscalls
 
-#ifdef CONFIG_NEED_RET_TO_USER
-#include <mach/entry-macro.S>
-#else
-	.macro  arch_ret_to_user, tmp1, tmp2
-	.endm
+	.macro  arch_ret_to_user, tmp
+#ifdef CONFIG_ARCH_IOP32X
+	mrc	p15, 0, \tmp, c15, c1, 0
+	tst	\tmp, #(1 << 6)
+	bicne	\tmp, \tmp, #(1 << 6)
+	mcrne	p15, 0, \tmp, c15, c1, 0	@ Disable cp6 access
 #endif
+	.endm
 
 #include "entry-header.S"
 
 saved_psr	.req	r8
-#if defined(CONFIG_TRACE_IRQFLAGS) || defined(CONFIG_CONTEXT_TRACKING)
+#if defined(CONFIG_TRACE_IRQFLAGS) || defined(CONFIG_CONTEXT_TRACKING_USER)
 saved_pc	.req	r9
 #define TRACE(x...) x
 #else
@@ -36,7 +38,7 @@ saved_pc	.req	lr
 
 	.section .entry.text,"ax",%progbits
 	.align	5
-#if !(IS_ENABLED(CONFIG_TRACE_IRQFLAGS) || IS_ENABLED(CONFIG_CONTEXT_TRACKING) || \
+#if !(IS_ENABLED(CONFIG_TRACE_IRQFLAGS) || IS_ENABLED(CONFIG_CONTEXT_TRACKING_USER) || \
 	IS_ENABLED(CONFIG_DEBUG_RSEQ))
 /*
  * This is the fast syscall return path.  We do as little as possible here,
@@ -55,7 +57,7 @@ __ret_fast_syscall:
 
 
 	/* perform architecture specific actions before user return */
-	arch_ret_to_user r1, lr
+	arch_ret_to_user r1
 
 	restore_user_regs fast = 1, offset = S_OFF
  UNWIND(.fnend		)
@@ -128,7 +130,7 @@ no_work_pending:
 	asm_trace_hardirqs_on save = 0
 
 	/* perform architecture specific actions before user return */
-	arch_ret_to_user r1, lr
+	arch_ret_to_user r1
 	ct_user_enter save = 0
 
 	restore_user_regs fast = 0, offset = 0
@@ -154,12 +156,36 @@ ENDPROC(ret_from_fork)
  */
 
 	.align	5
+#ifdef CONFIG_HARDEN_BRANCH_HISTORY
+ENTRY(vector_bhb_loop8_swi)
+	sub	sp, sp, #PT_REGS_SIZE
+	stmia	sp, {r0 - r12}
+	mov	r8, #8
+1:	b	2f
+2:	subs	r8, r8, #1
+	bne	1b
+	dsb	nsh
+	isb
+	b	3f
+ENDPROC(vector_bhb_loop8_swi)
+
+	.align	5
+ENTRY(vector_bhb_bpiall_swi)
+	sub	sp, sp, #PT_REGS_SIZE
+	stmia	sp, {r0 - r12}
+	mcr	p15, 0, r8, c7, c5, 6	@ BPIALL
+	isb
+	b	3f
+ENDPROC(vector_bhb_bpiall_swi)
+#endif
+	.align	5
 ENTRY(vector_swi)
 #ifdef CONFIG_CPU_V7M
 	v7m_exception_entry
 #else
 	sub	sp, sp, #PT_REGS_SIZE
 	stmia	sp, {r0 - r12}			@ Calling r0 - r12
+3:
  ARM(	add	r8, sp, #S_PC		)
  ARM(	stmdb	r8, {sp, lr}^		)	@ Calling sp, lr
  THUMB(	mov	r8, sp			)
@@ -172,7 +198,7 @@ ENTRY(vector_swi)
 #endif
 	reload_current r10, ip
 	zero_fp
-	alignment_trap r10, ip, __cr_alignment
+	alignment_trap r10, ip, cr_alignment
 	asm_trace_hardirqs_on save=0
 	enable_irq_notrace
 	ct_user_exit save=0
@@ -276,6 +302,7 @@ local_restart:
 	b	ret_fast_syscall
 #endif
 ENDPROC(vector_swi)
+	.ltorg
 
 	/*
 	 * This is the really slow path.  We're going to be doing
@@ -302,14 +329,6 @@ __sys_trace_return:
 	bl	syscall_trace_exit
 	b	ret_slow_syscall
 
-	.align	5
-#ifdef CONFIG_ALIGNMENT_TRAP
-	.type	__cr_alignment, #object
-__cr_alignment:
-	.word	cr_alignment
-#endif
-	.ltorg
-
 	.macro	syscall_table_start, sym
 	.equ	__sys_nr, 0
 	.type	\sym, #object
diff --git a/arch/arm/kernel/entry-ftrace.S b/arch/arm/kernel/entry-ftrace.S
index a74289ebc803..3e7bcaca5e07 100644
--- a/arch/arm/kernel/entry-ftrace.S
+++ b/arch/arm/kernel/entry-ftrace.S
@@ -22,12 +22,9 @@
  * mcount can be thought of as a function called in the middle of a subroutine
  * call.  As such, it needs to be transparent for both the caller and the
  * callee: the original lr needs to be restored when leaving mcount, and no
- * registers should be clobbered.  (In the __gnu_mcount_nc implementation, we
- * clobber the ip register.  This is OK because the ARM calling convention
- * allows it to be clobbered in subroutines and doesn't use it to hold
- * parameters.)
+ * registers should be clobbered.
  *
- * When using dynamic ftrace, we patch out the mcount call by a "pop {lr}"
+ * When using dynamic ftrace, we patch out the mcount call by a "add sp, #4"
  * instead of the __gnu_mcount_nc call (see arch/arm/kernel/ftrace.c).
  */
 
@@ -38,23 +35,20 @@
 
 .macro __mcount suffix
 	mcount_enter
-	ldr	r0, =ftrace_trace_function
-	ldr	r2, [r0]
-	adr	r0, .Lftrace_stub
+	ldr_va	r2, ftrace_trace_function
+	badr	r0, .Lftrace_stub
 	cmp	r0, r2
 	bne	1f
 
 #ifdef CONFIG_FUNCTION_GRAPH_TRACER
-	ldr     r1, =ftrace_graph_return
-	ldr     r2, [r1]
-	cmp     r0, r2
-	bne     ftrace_graph_caller\suffix
-
-	ldr     r1, =ftrace_graph_entry
-	ldr     r2, [r1]
-	ldr     r0, =ftrace_graph_entry_stub
-	cmp     r0, r2
-	bne     ftrace_graph_caller\suffix
+	ldr_va	r2, ftrace_graph_return
+	cmp	r0, r2
+	bne	ftrace_graph_caller\suffix
+
+	ldr_va	r2, ftrace_graph_entry
+	mov_l	r0, ftrace_graph_entry_stub
+	cmp	r0, r2
+	bne	ftrace_graph_caller\suffix
 #endif
 
 	mcount_exit
@@ -70,29 +64,27 @@
 
 .macro __ftrace_regs_caller
 
-	sub	sp, sp, #8	@ space for PC and CPSR OLD_R0,
+	str	lr, [sp, #-8]!	@ store LR as PC and make space for CPSR/OLD_R0,
 				@ OLD_R0 will overwrite previous LR
 
-	add 	ip, sp, #12	@ move in IP the value of SP as it was
-				@ before the push {lr} of the mcount mechanism
+	ldr	lr, [sp, #8]    @ get previous LR
 
-	str     lr, [sp, #0]    @ store LR instead of PC
+	str	r0, [sp, #8]	@ write r0 as OLD_R0 over previous LR
 
-	ldr     lr, [sp, #8]    @ get previous LR
+	str	lr, [sp, #-4]!	@ store previous LR as LR
 
-	str	r0, [sp, #8]	@ write r0 as OLD_R0 over previous LR
+	add 	lr, sp, #16	@ move in LR the value of SP as it was
+				@ before the push {lr} of the mcount mechanism
 
-	stmdb   sp!, {ip, lr}
-	stmdb   sp!, {r0-r11, lr}
+	push	{r0-r11, ip, lr}
 
 	@ stack content at this point:
 	@ 0  4          48   52       56            60   64    68       72
-	@ R0 | R1 | ... | LR | SP + 4 | previous LR | LR | PSR | OLD_R0 |
+	@ R0 | R1 | ... | IP | SP + 4 | previous LR | LR | PSR | OLD_R0 |
 
-	mov r3, sp				@ struct pt_regs*
+	mov	r3, sp				@ struct pt_regs*
 
-	ldr r2, =function_trace_op
-	ldr r2, [r2]				@ pointer to the current
+	ldr_va	r2, function_trace_op		@ pointer to the current
 						@ function tracing op
 
 	ldr	r1, [sp, #S_LR]			@ lr of instrumented func
@@ -108,35 +100,37 @@ ftrace_regs_call:
 #ifdef CONFIG_FUNCTION_GRAPH_TRACER
 	.globl ftrace_graph_regs_call
 ftrace_graph_regs_call:
-	mov	r0, r0
+ARM(	mov	r0, r0	)
+THUMB(	nop.w		)
 #endif
 
 	@ pop saved regs
-	ldmia   sp!, {r0-r12}			@ restore r0 through r12
-	ldr	ip, [sp, #8]			@ restore PC
-	ldr	lr, [sp, #4]			@ restore LR
-	ldr	sp, [sp, #0]			@ restore SP
-	mov	pc, ip				@ return
+	pop	{r0-r11, ip, lr}		@ restore r0 through r12
+	ldr	lr, [sp], #4			@ restore LR
+	ldr	pc, [sp], #12
 .endm
 
 #ifdef CONFIG_FUNCTION_GRAPH_TRACER
 .macro __ftrace_graph_regs_caller
 
-	sub     r0, fp, #4              @ lr of instrumented routine (parent)
+#ifdef CONFIG_UNWINDER_FRAME_POINTER
+	sub	r0, fp, #4		@ lr of instrumented routine (parent)
+#else
+	add	r0, sp, #S_LR
+#endif
 
 	@ called from __ftrace_regs_caller
-	ldr     r1, [sp, #S_PC]		@ instrumented routine (func)
+	ldr	r1, [sp, #S_PC]		@ instrumented routine (func)
 	mcount_adjust_addr	r1, r1
 
-	mov	r2, fp			@ frame pointer
+	mov	r2, fpreg		@ frame pointer
+	add	r3, sp, #PT_REGS_SIZE
 	bl	prepare_ftrace_return
 
 	@ pop registers saved in ftrace_regs_caller
-	ldmia   sp!, {r0-r12}			@ restore r0 through r12
-	ldr	ip, [sp, #8]			@ restore PC
-	ldr	lr, [sp, #4]			@ restore LR
-	ldr	sp, [sp, #0]			@ restore SP
-	mov	pc, ip				@ return
+	pop	{r0-r11, ip, lr}		@ restore r0 through r12
+	ldr	lr, [sp], #4			@ restore LR
+	ldr	pc, [sp], #12
 
 .endm
 #endif
@@ -149,8 +143,7 @@ ftrace_graph_regs_call:
 	mcount_adjust_addr	r0, lr		@ instrumented function
 
 #ifdef CONFIG_DYNAMIC_FTRACE_WITH_REGS
-	ldr r2, =function_trace_op
-	ldr r2, [r2]				@ pointer to the current
+	ldr_va	r2, function_trace_op		@ pointer to the current
 						@ function tracing op
 	mov r3, #0				@ regs is NULL
 #endif
@@ -162,14 +155,19 @@ ftrace_call\suffix:
 #ifdef CONFIG_FUNCTION_GRAPH_TRACER
 	.globl ftrace_graph_call\suffix
 ftrace_graph_call\suffix:
-	mov	r0, r0
+ARM(	mov	r0, r0	)
+THUMB(	nop.w		)
 #endif
 
 	mcount_exit
 .endm
 
 .macro __ftrace_graph_caller
+#ifdef CONFIG_UNWINDER_FRAME_POINTER
 	sub	r0, fp, #4		@ &lr of instrumented routine (&parent)
+#else
+	add	r0, sp, #20
+#endif
 #ifdef CONFIG_DYNAMIC_FTRACE
 	@ called from __ftrace_caller, saved in mcount_enter
 	ldr	r1, [sp, #16]		@ instrumented routine (func)
@@ -178,7 +176,8 @@ ftrace_graph_call\suffix:
 	@ called from __mcount, untouched in lr
 	mcount_adjust_addr	r1, lr	@ instrumented routine (func)
 #endif
-	mov	r2, fp			@ frame pointer
+	mov	r2, fpreg		@ frame pointer
+	add	r3, sp, #24
 	bl	prepare_ftrace_return
 	mcount_exit
 .endm
@@ -202,16 +201,17 @@ ftrace_graph_call\suffix:
 .endm
 
 .macro mcount_exit
-	ldmia	sp!, {r0-r3, ip, lr}
-	ret	ip
+	ldmia	sp!, {r0-r3}
+	ldr	lr, [sp, #4]
+	ldr	pc, [sp], #8
 .endm
 
 ENTRY(__gnu_mcount_nc)
 UNWIND(.fnstart)
 #ifdef CONFIG_DYNAMIC_FTRACE
-	mov	ip, lr
-	ldmia	sp!, {lr}
-	ret	ip
+	push	{lr}
+	ldr	lr, [sp, #4]
+	ldr	pc, [sp], #8
 #else
 	__mcount
 #endif
@@ -256,17 +256,33 @@ ENDPROC(ftrace_graph_regs_caller)
 .purgem mcount_exit
 
 #ifdef CONFIG_FUNCTION_GRAPH_TRACER
-	.globl return_to_handler
-return_to_handler:
+ENTRY(return_to_handler)
 	stmdb	sp!, {r0-r3}
-	mov	r0, fp			@ frame pointer
+	add	r0, sp, #16		@ sp at exit of instrumented routine
 	bl	ftrace_return_to_handler
 	mov	lr, r0			@ r0 has real ret addr
 	ldmia	sp!, {r0-r3}
 	ret	lr
+ENDPROC(return_to_handler)
 #endif
 
 ENTRY(ftrace_stub)
 .Lftrace_stub:
 	ret	lr
 ENDPROC(ftrace_stub)
+
+#ifdef CONFIG_DYNAMIC_FTRACE
+
+	__INIT
+
+	.macro	init_tramp, dst:req
+ENTRY(\dst\()_from_init)
+	ldr	pc, =\dst
+ENDPROC(\dst\()_from_init)
+	.endm
+
+	init_tramp	ftrace_caller
+#ifdef CONFIG_DYNAMIC_FTRACE_WITH_REGS
+	init_tramp	ftrace_regs_caller
+#endif
+#endif
diff --git a/arch/arm/kernel/entry-header.S b/arch/arm/kernel/entry-header.S
index ae24dd54e9ef..99411fa91350 100644
--- a/arch/arm/kernel/entry-header.S
+++ b/arch/arm/kernel/entry-header.S
@@ -48,8 +48,7 @@
 	.macro	alignment_trap, rtmp1, rtmp2, label
 #ifdef CONFIG_ALIGNMENT_TRAP
 	mrc	p15, 0, \rtmp2, c1, c0, 0
-	ldr	\rtmp1, \label
-	ldr	\rtmp1, [\rtmp1]
+	ldr_va	\rtmp1, \label
 	teq	\rtmp1, \rtmp2
 	mcrne	p15, 0, \rtmp1, c1, c0, 0
 #endif
@@ -292,12 +291,18 @@
 
 
 	.macro	restore_user_regs, fast = 0, offset = 0
-#if defined(CONFIG_CPU_32v6K) && !defined(CONFIG_CPU_V6)
+#if defined(CONFIG_CPU_32v6K) && \
+    (!defined(CONFIG_CPU_V6) || defined(CONFIG_SMP))
+#ifdef CONFIG_CPU_V6
+ALT_SMP(nop)
+ALT_UP_B(.L1_\@)
+#endif
 	@ The TLS register update is deferred until return to user space so we
 	@ can use it for other things while running in the kernel
-	get_thread_info r1
+	mrc	p15, 0, r1, c13, c0, 3		@ get current_thread_info pointer
 	ldr	r1, [r1, #TI_TP_VALUE]
 	mcr	p15, 0, r1, c13, c0, 3		@ set TLS register
+.L1_\@:
 #endif
 
 	uaccess_enable r1, isb=0
@@ -361,25 +366,25 @@
  * between user and kernel mode.
  */
 	.macro ct_user_exit, save = 1
-#ifdef CONFIG_CONTEXT_TRACKING
+#ifdef CONFIG_CONTEXT_TRACKING_USER
 	.if	\save
 	stmdb   sp!, {r0-r3, ip, lr}
-	bl	context_tracking_user_exit
+	bl	user_exit_callable
 	ldmia	sp!, {r0-r3, ip, lr}
 	.else
-	bl	context_tracking_user_exit
+	bl	user_exit_callable
 	.endif
 #endif
 	.endm
 
 	.macro ct_user_enter, save = 1
-#ifdef CONFIG_CONTEXT_TRACKING
+#ifdef CONFIG_CONTEXT_TRACKING_USER
 	.if	\save
 	stmdb   sp!, {r0-r3, ip, lr}
-	bl	context_tracking_user_enter
+	bl	user_enter_callable
 	ldmia	sp!, {r0-r3, ip, lr}
 	.else
-	bl	context_tracking_user_enter
+	bl	user_enter_callable
 	.endif
 #endif
 	.endm
@@ -423,3 +428,40 @@ scno	.req	r7		@ syscall number
 tbl	.req	r8		@ syscall table pointer
 why	.req	r8		@ Linux syscall (!= 0)
 tsk	.req	r9		@ current thread_info
+
+	.macro	do_overflow_check, frame_size:req
+#ifdef CONFIG_VMAP_STACK
+	@
+	@ Test whether the SP has overflowed. Task and IRQ stacks are aligned
+	@ so that SP & BIT(THREAD_SIZE_ORDER + PAGE_SHIFT) should always be
+	@ zero.
+	@
+ARM(	tst	sp, #1 << (THREAD_SIZE_ORDER + PAGE_SHIFT)	)
+THUMB(	tst	r1, #1 << (THREAD_SIZE_ORDER + PAGE_SHIFT)	)
+THUMB(	it	ne						)
+	bne	.Lstack_overflow_check\@
+
+	.pushsection	.text
+.Lstack_overflow_check\@:
+	@
+	@ The stack pointer is not pointing to a valid vmap'ed stack, but it
+	@ may be pointing into the linear map instead, which may happen if we
+	@ are already running from the overflow stack. We cannot detect overflow
+	@ in such cases so just carry on.
+	@
+	str	ip, [r0, #12]			@ Stash IP on the mode stack
+	ldr_va	ip, high_memory			@ Start of VMALLOC space
+ARM(	cmp	sp, ip			)	@ SP in vmalloc space?
+THUMB(	cmp	r1, ip			)
+THUMB(	itt	lo			)
+	ldrlo	ip, [r0, #12]			@ Restore IP
+	blo	.Lout\@				@ Carry on
+
+THUMB(	sub	r1, sp, r1		)	@ Restore original R1
+THUMB(	sub	sp, r1			)	@ Restore original SP
+	add	sp, sp, #\frame_size		@ Undo svc_entry's SP change
+	b	__bad_stack			@ Handle VMAP stack overflow
+	.popsection
+.Lout\@:
+#endif
+	.endm
diff --git a/arch/arm/kernel/entry-v7m.S b/arch/arm/kernel/entry-v7m.S
index 7bde93c10962..de8a60363c85 100644
--- a/arch/arm/kernel/entry-v7m.S
+++ b/arch/arm/kernel/entry-v7m.S
@@ -39,16 +39,25 @@ __irq_entry:
 	@
 	@ Invoke the IRQ handler
 	@
-	mrs	r0, ipsr
-	ldr	r1, =V7M_xPSR_EXCEPTIONNO
-	and	r0, r1
-	sub	r0, #16
-	mov	r1, sp
-	stmdb	sp!, {lr}
-	@ routine called with r0 = irq number, r1 = struct pt_regs *
-	bl	nvic_handle_irq
-
-	pop	{lr}
+	mov	r0, sp
+	ldr_this_cpu sp, irq_stack_ptr, r1, r2
+
+	@
+	@ If we took the interrupt while running in the kernel, we may already
+	@ be using the IRQ stack, so revert to the original value in that case.
+	@
+	subs	r2, sp, r0		@ SP above bottom of IRQ stack?
+	rsbscs	r2, r2, #THREAD_SIZE	@ ... and below the top?
+	movcs	sp, r0
+
+	push	{r0, lr}		@ preserve LR and original SP
+
+	@ routine called with r0 = struct pt_regs *
+	bl	generic_handle_arch_irq
+
+	pop	{r0, lr}
+	mov	sp, r0
+
 	@
 	@ Check for any pending work if returning to user
 	@
@@ -101,15 +110,17 @@ ENTRY(__switch_to)
 	str	sp, [ip], #4
 	str	lr, [ip], #4
 	mov	r5, r0
+	mov	r6, r2			@ Preserve 'next'
 	add	r4, r2, #TI_CPU_SAVE
 	ldr	r0, =thread_notify_head
 	mov	r1, #THREAD_NOTIFY_SWITCH
 	bl	atomic_notifier_call_chain
-	mov	ip, r4
 	mov	r0, r5
-	ldmia	ip!, {r4 - r11}		@ Load all regs saved previously
-	ldr	sp, [ip]
-	ldr	pc, [ip, #4]!
+	mov	r1, r6
+	ldmia	r4, {r4 - r12, lr}	@ Load all regs saved previously
+	set_current r1, r2
+	mov	sp, ip
+	bx	lr
 	.fnend
 ENDPROC(__switch_to)
 
diff --git a/arch/arm/kernel/ftrace.c b/arch/arm/kernel/ftrace.c
index a006585e1c09..a0b6d1e3812f 100644
--- a/arch/arm/kernel/ftrace.c
+++ b/arch/arm/kernel/ftrace.c
@@ -22,12 +22,24 @@
 #include <asm/ftrace.h>
 #include <asm/insn.h>
 #include <asm/set_memory.h>
+#include <asm/stacktrace.h>
 #include <asm/patch.h>
 
+/*
+ * The compiler emitted profiling hook consists of
+ *
+ *   PUSH    {LR}
+ *   BL	     __gnu_mcount_nc
+ *
+ * To turn this combined sequence into a NOP, we need to restore the value of
+ * SP before the PUSH. Let's use an ADD rather than a POP into LR, as LR is not
+ * modified anyway, and reloading LR from memory is highly likely to be less
+ * efficient.
+ */
 #ifdef CONFIG_THUMB2_KERNEL
-#define	NOP		0xf85deb04	/* pop.w {lr} */
+#define	NOP		0xf10d0d04	/* add.w sp, sp, #4 */
 #else
-#define	NOP		0xe8bd4000	/* pop {lr} */
+#define	NOP		0xe28dd004	/* add   sp, sp, #4 */
 #endif
 
 #ifdef CONFIG_DYNAMIC_FTRACE
@@ -51,21 +63,30 @@ static unsigned long ftrace_nop_replace(struct dyn_ftrace *rec)
 	return NOP;
 }
 
-static unsigned long adjust_address(struct dyn_ftrace *rec, unsigned long addr)
+void ftrace_caller_from_init(void);
+void ftrace_regs_caller_from_init(void);
+
+static unsigned long __ref adjust_address(struct dyn_ftrace *rec,
+					  unsigned long addr)
 {
-	return addr;
+	if (!IS_ENABLED(CONFIG_DYNAMIC_FTRACE) ||
+	    system_state >= SYSTEM_FREEING_INITMEM ||
+	    likely(!is_kernel_inittext(rec->ip)))
+		return addr;
+	if (!IS_ENABLED(CONFIG_DYNAMIC_FTRACE_WITH_REGS) ||
+	    addr == (unsigned long)&ftrace_caller)
+		return (unsigned long)&ftrace_caller_from_init;
+	return (unsigned long)&ftrace_regs_caller_from_init;
 }
 
-int ftrace_arch_code_modify_prepare(void)
+void ftrace_arch_code_modify_prepare(void)
 {
-	return 0;
 }
 
-int ftrace_arch_code_modify_post_process(void)
+void ftrace_arch_code_modify_post_process(void)
 {
 	/* Make sure any TLB misses during machine stop are cleared. */
 	flush_tlb_all();
-	return 0;
 }
 
 static unsigned long ftrace_call_replace(unsigned long pc, unsigned long addr,
@@ -189,15 +210,23 @@ int ftrace_make_nop(struct module *mod,
 #endif
 
 	new = ftrace_nop_replace(rec);
-	ret = ftrace_modify_code(ip, old, new, true);
+	/*
+	 * Locations in .init.text may call __gnu_mcount_mc via a linker
+	 * emitted veneer if they are too far away from its implementation, and
+	 * so validation may fail spuriously in such cases. Let's work around
+	 * this by omitting those from validation.
+	 */
+	ret = ftrace_modify_code(ip, old, new, !is_kernel_inittext(ip));
 
 	return ret;
 }
 #endif /* CONFIG_DYNAMIC_FTRACE */
 
 #ifdef CONFIG_FUNCTION_GRAPH_TRACER
+asmlinkage
 void prepare_ftrace_return(unsigned long *parent, unsigned long self_addr,
-			   unsigned long frame_pointer)
+			   unsigned long frame_pointer,
+			   unsigned long stack_pointer)
 {
 	unsigned long return_hooker = (unsigned long) &return_to_handler;
 	unsigned long old;
@@ -205,6 +234,23 @@ void prepare_ftrace_return(unsigned long *parent, unsigned long self_addr,
 	if (unlikely(atomic_read(&current->tracing_graph_pause)))
 		return;
 
+	if (IS_ENABLED(CONFIG_UNWINDER_FRAME_POINTER)) {
+		/* FP points one word below parent's top of stack */
+		frame_pointer += 4;
+	} else {
+		struct stackframe frame = {
+			.fp = frame_pointer,
+			.sp = stack_pointer,
+			.lr = self_addr,
+			.pc = self_addr,
+		};
+		if (unwind_frame(&frame) < 0)
+			return;
+		if (frame.lr != self_addr)
+			parent = frame.lr_addr;
+		frame_pointer = frame.sp;
+	}
+
 	old = *parent;
 	*parent = return_hooker;
 
@@ -225,7 +271,7 @@ static int __ftrace_modify_caller(unsigned long *callsite,
 	unsigned long caller_fn = (unsigned long) func;
 	unsigned long pc = (unsigned long) callsite;
 	unsigned long branch = arm_gen_branch(pc, caller_fn);
-	unsigned long nop = 0xe1a00000;	/* mov r0, r0 */
+	unsigned long nop = arm_gen_nop();
 	unsigned long old = enable ? nop : branch;
 	unsigned long new = enable ? branch : nop;
 
diff --git a/arch/arm/kernel/head-common.S b/arch/arm/kernel/head-common.S
index da18e0a17dc2..42cae73fcc19 100644
--- a/arch/arm/kernel/head-common.S
+++ b/arch/arm/kernel/head-common.S
@@ -105,10 +105,8 @@ __mmap_switched:
 	mov	r1, #0
 	bl	__memset			@ clear .bss
 
-#ifdef CONFIG_CURRENT_POINTER_IN_TPIDRURO
 	adr_l	r0, init_task			@ get swapper task_struct
-	set_current r0
-#endif
+	set_current r0, r1
 
 	ldmia	r4, {r0, r1, r2, r3}
 	str	r9, [r0]			@ Save processor ID
diff --git a/arch/arm/kernel/head-nommu.S b/arch/arm/kernel/head-nommu.S
index fadfee9e2b45..950bef83339f 100644
--- a/arch/arm/kernel/head-nommu.S
+++ b/arch/arm/kernel/head-nommu.S
@@ -114,6 +114,7 @@ ENTRY(secondary_startup)
 	add	r12, r12, r10
 	ret	r12
 1:	bl	__after_proc_init
+	ldr	r7, __secondary_data		@ reload r7
 	ldr	sp, [r7, #12]			@ set up the stack pointer
 	ldr	r0, [r7, #16]			@ set up task pointer
 	mov	fp, #0
diff --git a/arch/arm/kernel/head.S b/arch/arm/kernel/head.S
index c04dd94630c7..29e2900178a1 100644
--- a/arch/arm/kernel/head.S
+++ b/arch/arm/kernel/head.S
@@ -38,10 +38,10 @@
 #ifdef CONFIG_ARM_LPAE
 	/* LPAE requires an additional page for the PGD */
 #define PG_DIR_SIZE	0x5000
-#define PMD_ORDER	3
+#define PMD_ENTRY_ORDER	3	/* PMD entry size is 2^PMD_ENTRY_ORDER */
 #else
 #define PG_DIR_SIZE	0x4000
-#define PMD_ORDER	2
+#define PMD_ENTRY_ORDER	2
 #endif
 
 	.globl	swapper_pg_dir
@@ -240,7 +240,7 @@ __create_page_tables:
 	mov	r6, r6, lsr #SECTION_SHIFT
 
 1:	orr	r3, r7, r5, lsl #SECTION_SHIFT	@ flags + kernel base
-	str	r3, [r4, r5, lsl #PMD_ORDER]	@ identity mapping
+	str	r3, [r4, r5, lsl #PMD_ENTRY_ORDER]	@ identity mapping
 	cmp	r5, r6
 	addlo	r5, r5, #1			@ next section
 	blo	1b
@@ -250,7 +250,7 @@ __create_page_tables:
 	 * set two variables to indicate the physical start and end of the
 	 * kernel.
 	 */
-	add	r0, r4, #KERNEL_OFFSET >> (SECTION_SHIFT - PMD_ORDER)
+	add	r0, r4, #KERNEL_OFFSET >> (SECTION_SHIFT - PMD_ENTRY_ORDER)
 	ldr	r6, =(_end - 1)
 	adr_l	r5, kernel_sec_start		@ _pa(kernel_sec_start)
 #if defined CONFIG_CPU_ENDIAN_BE8 || defined CONFIG_CPU_ENDIAN_BE32
@@ -259,8 +259,8 @@ __create_page_tables:
 	str	r8, [r5]			@ Save physical start of kernel (LE)
 #endif
 	orr	r3, r8, r7			@ Add the MMU flags
-	add	r6, r4, r6, lsr #(SECTION_SHIFT - PMD_ORDER)
-1:	str	r3, [r0], #1 << PMD_ORDER
+	add	r6, r4, r6, lsr #(SECTION_SHIFT - PMD_ENTRY_ORDER)
+1:	str	r3, [r0], #1 << PMD_ENTRY_ORDER
 	add	r3, r3, #1 << SECTION_SHIFT
 	cmp	r0, r6
 	bls	1b
@@ -280,14 +280,14 @@ __create_page_tables:
 	mov	r3, pc
 	mov	r3, r3, lsr #SECTION_SHIFT
 	orr	r3, r7, r3, lsl #SECTION_SHIFT
-	add	r0, r4,  #(XIP_START & 0xff000000) >> (SECTION_SHIFT - PMD_ORDER)
-	str	r3, [r0, #((XIP_START & 0x00f00000) >> SECTION_SHIFT) << PMD_ORDER]!
+	add	r0, r4,  #(XIP_START & 0xff000000) >> (SECTION_SHIFT - PMD_ENTRY_ORDER)
+	str	r3, [r0, #((XIP_START & 0x00f00000) >> SECTION_SHIFT) << PMD_ENTRY_ORDER]!
 	ldr	r6, =(_edata_loc - 1)
-	add	r0, r0, #1 << PMD_ORDER
-	add	r6, r4, r6, lsr #(SECTION_SHIFT - PMD_ORDER)
+	add	r0, r0, #1 << PMD_ENTRY_ORDER
+	add	r6, r4, r6, lsr #(SECTION_SHIFT - PMD_ENTRY_ORDER)
 1:	cmp	r0, r6
 	add	r3, r3, #1 << SECTION_SHIFT
-	strls	r3, [r0], #1 << PMD_ORDER
+	strls	r3, [r0], #1 << PMD_ENTRY_ORDER
 	bls	1b
 #endif
 
@@ -297,10 +297,10 @@ __create_page_tables:
 	 */
 	mov	r0, r2, lsr #SECTION_SHIFT
 	cmp	r2, #0
-	ldrne	r3, =FDT_FIXED_BASE >> (SECTION_SHIFT - PMD_ORDER)
+	ldrne	r3, =FDT_FIXED_BASE >> (SECTION_SHIFT - PMD_ENTRY_ORDER)
 	addne	r3, r3, r4
 	orrne	r6, r7, r0, lsl #SECTION_SHIFT
-	strne	r6, [r3], #1 << PMD_ORDER
+	strne	r6, [r3], #1 << PMD_ENTRY_ORDER
 	addne	r6, r6, #1 << SECTION_SHIFT
 	strne	r6, [r3]
 
@@ -319,7 +319,7 @@ __create_page_tables:
 	addruart r7, r3, r0
 
 	mov	r3, r3, lsr #SECTION_SHIFT
-	mov	r3, r3, lsl #PMD_ORDER
+	mov	r3, r3, lsl #PMD_ENTRY_ORDER
 
 	add	r0, r4, r3
 	mov	r3, r7, lsr #SECTION_SHIFT
@@ -349,7 +349,7 @@ __create_page_tables:
 	 * If we're using the NetWinder or CATS, we also need to map
 	 * in the 16550-type serial port for the debug messages
 	 */
-	add	r0, r4, #0xff000000 >> (SECTION_SHIFT - PMD_ORDER)
+	add	r0, r4, #0xff000000 >> (SECTION_SHIFT - PMD_ENTRY_ORDER)
 	orr	r3, r7, #0x7c000000
 	str	r3, [r0]
 #endif
@@ -359,10 +359,10 @@ __create_page_tables:
 	 * Similar reasons here - for debug.  This is
 	 * only for Acorn RiscPC architectures.
 	 */
-	add	r0, r4, #0x02000000 >> (SECTION_SHIFT - PMD_ORDER)
+	add	r0, r4, #0x02000000 >> (SECTION_SHIFT - PMD_ENTRY_ORDER)
 	orr	r3, r7, #0x02000000
 	str	r3, [r0]
-	add	r0, r4, #0xd8000000 >> (SECTION_SHIFT - PMD_ORDER)
+	add	r0, r4, #0xd8000000 >> (SECTION_SHIFT - PMD_ENTRY_ORDER)
 	str	r3, [r0]
 #endif
 #endif
@@ -424,6 +424,13 @@ ENDPROC(secondary_startup)
 ENDPROC(secondary_startup_arm)
 
 ENTRY(__secondary_switched)
+#if defined(CONFIG_VMAP_STACK) && !defined(CONFIG_ARM_LPAE)
+	@ Before using the vmap'ed stack, we have to switch to swapper_pg_dir
+	@ as the ID map does not cover the vmalloc region.
+	mrc	p15, 0, ip, c2, c0, 1	@ read TTBR1
+	mcr	p15, 0, ip, c2, c0, 0	@ set TTBR0
+	instr_sync
+#endif
 	adr_l	r7, secondary_data + 12		@ get secondary_data.stack
 	ldr	sp, [r7]
 	ldr	r0, [r7, #4]			@ get secondary_data.task
diff --git a/arch/arm/kernel/hw_breakpoint.c b/arch/arm/kernel/hw_breakpoint.c
index b1423fb130ea..054e9199f30d 100644
--- a/arch/arm/kernel/hw_breakpoint.c
+++ b/arch/arm/kernel/hw_breakpoint.c
@@ -941,6 +941,23 @@ static int hw_breakpoint_pending(unsigned long addr, unsigned int fsr,
 	return ret;
 }
 
+#ifdef CONFIG_ARM_ERRATA_764319
+static int oslsr_fault;
+
+static int debug_oslsr_trap(struct pt_regs *regs, unsigned int instr)
+{
+	oslsr_fault = 1;
+	instruction_pointer(regs) += 4;
+	return 0;
+}
+
+static struct undef_hook debug_oslsr_hook = {
+	.instr_mask  = 0xffffffff,
+	.instr_val = 0xee115e91,
+	.fn = debug_oslsr_trap,
+};
+#endif
+
 /*
  * One-time initialisation.
  */
@@ -974,7 +991,16 @@ static bool core_has_os_save_restore(void)
 	case ARM_DEBUG_ARCH_V7_1:
 		return true;
 	case ARM_DEBUG_ARCH_V7_ECP14:
+#ifdef CONFIG_ARM_ERRATA_764319
+		oslsr_fault = 0;
+		register_undef_hook(&debug_oslsr_hook);
 		ARM_DBG_READ(c1, c1, 4, oslsr);
+		unregister_undef_hook(&debug_oslsr_hook);
+		if (oslsr_fault)
+			return false;
+#else
+		ARM_DBG_READ(c1, c1, 4, oslsr);
+#endif
 		if (oslsr & ARM_OSLSR_OSLM0)
 			return true;
 		fallthrough;
diff --git a/arch/arm/kernel/irq.c b/arch/arm/kernel/irq.c
index b79975bd988c..fe28fc1f759d 100644
--- a/arch/arm/kernel/irq.c
+++ b/arch/arm/kernel/irq.c
@@ -36,13 +36,54 @@
 #include <asm/hardware/cache-l2x0.h>
 #include <asm/hardware/cache-uniphier.h>
 #include <asm/outercache.h>
+#include <asm/softirq_stack.h>
 #include <asm/exception.h>
 #include <asm/mach/arch.h>
 #include <asm/mach/irq.h>
 #include <asm/mach/time.h>
 
+#include "reboot.h"
+
 unsigned long irq_err_count;
 
+#ifdef CONFIG_IRQSTACKS
+
+asmlinkage DEFINE_PER_CPU_READ_MOSTLY(u8 *, irq_stack_ptr);
+
+static void __init init_irq_stacks(void)
+{
+	u8 *stack;
+	int cpu;
+
+	for_each_possible_cpu(cpu) {
+		if (!IS_ENABLED(CONFIG_VMAP_STACK))
+			stack = (u8 *)__get_free_pages(GFP_KERNEL,
+						       THREAD_SIZE_ORDER);
+		else
+			stack = __vmalloc_node(THREAD_SIZE, THREAD_ALIGN,
+					       THREADINFO_GFP, NUMA_NO_NODE,
+					       __builtin_return_address(0));
+
+		if (WARN_ON(!stack))
+			break;
+		per_cpu(irq_stack_ptr, cpu) = &stack[THREAD_SIZE];
+	}
+}
+
+#ifdef CONFIG_SOFTIRQ_ON_OWN_STACK
+static void ____do_softirq(void *arg)
+{
+	__do_softirq();
+}
+
+void do_softirq_own_stack(void)
+{
+	call_with_stack(____do_softirq, NULL,
+			__this_cpu_read(irq_stack_ptr));
+}
+#endif
+#endif
+
 int arch_show_interrupts(struct seq_file *p, int prec)
 {
 #ifdef CONFIG_FIQ
@@ -80,27 +121,14 @@ void handle_IRQ(unsigned int irq, struct pt_regs *regs)
 		ack_bad_irq(irq);
 }
 
-/*
- * asm_do_IRQ is the interface to be used from assembly code.
- */
-asmlinkage void __exception_irq_entry
-asm_do_IRQ(unsigned int irq, struct pt_regs *regs)
-{
-	struct pt_regs *old_regs;
-
-	irq_enter();
-	old_regs = set_irq_regs(regs);
-
-	handle_IRQ(irq, regs);
-
-	set_irq_regs(old_regs);
-	irq_exit();
-}
-
 void __init init_IRQ(void)
 {
 	int ret;
 
+#ifdef CONFIG_IRQSTACKS
+	init_irq_stacks();
+#endif
+
 	if (IS_ENABLED(CONFIG_OF) && !machine_desc->init_irq)
 		irqchip_init();
 	else
diff --git a/arch/arm/kernel/jump_label.c b/arch/arm/kernel/jump_label.c
index 303b3ab87f7e..eb9c24b6e8e2 100644
--- a/arch/arm/kernel/jump_label.c
+++ b/arch/arm/kernel/jump_label.c
@@ -27,9 +27,3 @@ void arch_jump_label_transform(struct jump_entry *entry,
 {
 	__arch_jump_label_transform(entry, type, false);
 }
-
-void arch_jump_label_transform_static(struct jump_entry *entry,
-				      enum jump_label_type type)
-{
-	__arch_jump_label_transform(entry, type, true);
-}
diff --git a/arch/arm/kernel/kgdb.c b/arch/arm/kernel/kgdb.c
index 7bd30c0a4280..22f937e6f3ff 100644
--- a/arch/arm/kernel/kgdb.c
+++ b/arch/arm/kernel/kgdb.c
@@ -154,22 +154,38 @@ static int kgdb_compiled_brk_fn(struct pt_regs *regs, unsigned int instr)
 	return 0;
 }
 
-static struct undef_hook kgdb_brkpt_hook = {
+static struct undef_hook kgdb_brkpt_arm_hook = {
 	.instr_mask		= 0xffffffff,
 	.instr_val		= KGDB_BREAKINST,
-	.cpsr_mask		= MODE_MASK,
+	.cpsr_mask		= PSR_T_BIT | MODE_MASK,
 	.cpsr_val		= SVC_MODE,
 	.fn			= kgdb_brk_fn
 };
 
-static struct undef_hook kgdb_compiled_brkpt_hook = {
+static struct undef_hook kgdb_brkpt_thumb_hook = {
+	.instr_mask		= 0xffff,
+	.instr_val		= KGDB_BREAKINST & 0xffff,
+	.cpsr_mask		= PSR_T_BIT | MODE_MASK,
+	.cpsr_val		= PSR_T_BIT | SVC_MODE,
+	.fn			= kgdb_brk_fn
+};
+
+static struct undef_hook kgdb_compiled_brkpt_arm_hook = {
 	.instr_mask		= 0xffffffff,
 	.instr_val		= KGDB_COMPILED_BREAK,
-	.cpsr_mask		= MODE_MASK,
+	.cpsr_mask		= PSR_T_BIT | MODE_MASK,
 	.cpsr_val		= SVC_MODE,
 	.fn			= kgdb_compiled_brk_fn
 };
 
+static struct undef_hook kgdb_compiled_brkpt_thumb_hook = {
+	.instr_mask		= 0xffff,
+	.instr_val		= KGDB_COMPILED_BREAK & 0xffff,
+	.cpsr_mask		= PSR_T_BIT | MODE_MASK,
+	.cpsr_val		= PSR_T_BIT | SVC_MODE,
+	.fn			= kgdb_compiled_brk_fn
+};
+
 static int __kgdb_notify(struct die_args *args, unsigned long cmd)
 {
 	struct pt_regs *regs = args->regs;
@@ -210,8 +226,10 @@ int kgdb_arch_init(void)
 	if (ret != 0)
 		return ret;
 
-	register_undef_hook(&kgdb_brkpt_hook);
-	register_undef_hook(&kgdb_compiled_brkpt_hook);
+	register_undef_hook(&kgdb_brkpt_arm_hook);
+	register_undef_hook(&kgdb_brkpt_thumb_hook);
+	register_undef_hook(&kgdb_compiled_brkpt_arm_hook);
+	register_undef_hook(&kgdb_compiled_brkpt_thumb_hook);
 
 	return 0;
 }
@@ -224,8 +242,10 @@ int kgdb_arch_init(void)
  */
 void kgdb_arch_exit(void)
 {
-	unregister_undef_hook(&kgdb_brkpt_hook);
-	unregister_undef_hook(&kgdb_compiled_brkpt_hook);
+	unregister_undef_hook(&kgdb_brkpt_arm_hook);
+	unregister_undef_hook(&kgdb_brkpt_thumb_hook);
+	unregister_undef_hook(&kgdb_compiled_brkpt_arm_hook);
+	unregister_undef_hook(&kgdb_compiled_brkpt_thumb_hook);
 	unregister_die_notifier(&kgdb_notifier);
 }
 
diff --git a/arch/arm/kernel/module.c b/arch/arm/kernel/module.c
index beac45e89ba6..d59c36dc0494 100644
--- a/arch/arm/kernel/module.c
+++ b/arch/arm/kernel/module.c
@@ -68,6 +68,44 @@ bool module_exit_section(const char *name)
 		strstarts(name, ".ARM.exidx.exit");
 }
 
+#ifdef CONFIG_ARM_HAS_GROUP_RELOCS
+/*
+ * This implements the partitioning algorithm for group relocations as
+ * documented in the ARM AArch32 ELF psABI (IHI 0044).
+ *
+ * A single PC-relative symbol reference is divided in up to 3 add or subtract
+ * operations, where the final one could be incorporated into a load/store
+ * instruction with immediate offset. E.g.,
+ *
+ *   ADD	Rd, PC, #...		or	ADD	Rd, PC, #...
+ *   ADD	Rd, Rd, #...			ADD	Rd, Rd, #...
+ *   LDR	Rd, [Rd, #...]			ADD	Rd, Rd, #...
+ *
+ * The latter has a guaranteed range of only 16 MiB (3x8 == 24 bits), so it is
+ * of limited use in the kernel. However, the ADD/ADD/LDR combo has a range of
+ * -/+ 256 MiB, (2x8 + 12 == 28 bits), which means it has sufficient range for
+ * any in-kernel symbol reference (unless module PLTs are being used).
+ *
+ * The main advantage of this approach over the typical pattern using a literal
+ * load is that literal loads may miss in the D-cache, and generally lead to
+ * lower cache efficiency for variables that are referenced often from many
+ * different places in the code.
+ */
+static u32 get_group_rem(u32 group, u32 *offset)
+{
+	u32 val = *offset;
+	u32 shift;
+	do {
+		shift = val ? (31 - __fls(val)) & ~1 : 32;
+		*offset = val;
+		if (!val)
+			break;
+		val &= 0xffffff >> shift;
+	} while (group--);
+	return shift;
+}
+#endif
+
 int
 apply_relocate(Elf32_Shdr *sechdrs, const char *strtab, unsigned int symindex,
 	       unsigned int relindex, struct module *module)
@@ -82,6 +120,9 @@ apply_relocate(Elf32_Shdr *sechdrs, const char *strtab, unsigned int symindex,
 		unsigned long loc;
 		Elf32_Sym *sym;
 		const char *symname;
+#ifdef CONFIG_ARM_HAS_GROUP_RELOCS
+		u32 shift, group = 1;
+#endif
 		s32 offset;
 		u32 tmp;
 #ifdef CONFIG_THUMB2_KERNEL
@@ -212,6 +253,55 @@ apply_relocate(Elf32_Shdr *sechdrs, const char *strtab, unsigned int symindex,
 			*(u32 *)loc = __opcode_to_mem_arm(tmp);
 			break;
 
+#ifdef CONFIG_ARM_HAS_GROUP_RELOCS
+		case R_ARM_ALU_PC_G0_NC:
+			group = 0;
+			fallthrough;
+		case R_ARM_ALU_PC_G1_NC:
+			tmp = __mem_to_opcode_arm(*(u32 *)loc);
+			offset = ror32(tmp & 0xff, (tmp & 0xf00) >> 7);
+			if (tmp & BIT(22))
+				offset = -offset;
+			offset += sym->st_value - loc;
+			if (offset < 0) {
+				offset = -offset;
+				tmp = (tmp & ~BIT(23)) | BIT(22); // SUB opcode
+			} else {
+				tmp = (tmp & ~BIT(22)) | BIT(23); // ADD opcode
+			}
+
+			shift = get_group_rem(group, &offset);
+			if (shift < 24) {
+				offset >>= 24 - shift;
+				offset |= (shift + 8) << 7;
+			}
+			*(u32 *)loc = __opcode_to_mem_arm((tmp & ~0xfff) | offset);
+			break;
+
+		case R_ARM_LDR_PC_G2:
+			tmp = __mem_to_opcode_arm(*(u32 *)loc);
+			offset = tmp & 0xfff;
+			if (~tmp & BIT(23))		// U bit cleared?
+				offset = -offset;
+			offset += sym->st_value - loc;
+			if (offset < 0) {
+				offset = -offset;
+				tmp &= ~BIT(23);	// clear U bit
+			} else {
+				tmp |= BIT(23);		// set U bit
+			}
+			get_group_rem(2, &offset);
+
+			if (offset > 0xfff) {
+				pr_err("%s: section %u reloc %u sym '%s': relocation %u out of range (%#lx -> %#x)\n",
+				       module->name, relindex, i, symname,
+				       ELF32_R_TYPE(rel->r_info), loc,
+				       sym->st_value);
+				return -ENOEXEC;
+			}
+			*(u32 *)loc = __opcode_to_mem_arm((tmp & ~0xfff) | offset);
+			break;
+#endif
 #ifdef CONFIG_THUMB2_KERNEL
 		case R_ARM_THM_CALL:
 		case R_ARM_THM_JUMP24:
@@ -369,46 +459,40 @@ int module_finalize(const Elf32_Ehdr *hdr, const Elf_Shdr *sechdrs,
 #ifdef CONFIG_ARM_UNWIND
 	const char *secstrs = (void *)hdr + sechdrs[hdr->e_shstrndx].sh_offset;
 	const Elf_Shdr *sechdrs_end = sechdrs + hdr->e_shnum;
-	struct mod_unwind_map maps[ARM_SEC_MAX];
-	int i;
+	struct list_head *unwind_list = &mod->arch.unwind_list;
 
-	memset(maps, 0, sizeof(maps));
+	INIT_LIST_HEAD(unwind_list);
+	mod->arch.init_table = NULL;
 
 	for (s = sechdrs; s < sechdrs_end; s++) {
 		const char *secname = secstrs + s->sh_name;
+		const char *txtname;
+		const Elf_Shdr *txt_sec;
 
-		if (!(s->sh_flags & SHF_ALLOC))
+		if (!(s->sh_flags & SHF_ALLOC) ||
+		    s->sh_type != ELF_SECTION_UNWIND)
 			continue;
 
-		if (strcmp(".ARM.exidx.init.text", secname) == 0)
-			maps[ARM_SEC_INIT].unw_sec = s;
-		else if (strcmp(".ARM.exidx", secname) == 0)
-			maps[ARM_SEC_CORE].unw_sec = s;
-		else if (strcmp(".ARM.exidx.exit.text", secname) == 0)
-			maps[ARM_SEC_EXIT].unw_sec = s;
-		else if (strcmp(".ARM.exidx.text.unlikely", secname) == 0)
-			maps[ARM_SEC_UNLIKELY].unw_sec = s;
-		else if (strcmp(".ARM.exidx.text.hot", secname) == 0)
-			maps[ARM_SEC_HOT].unw_sec = s;
-		else if (strcmp(".init.text", secname) == 0)
-			maps[ARM_SEC_INIT].txt_sec = s;
-		else if (strcmp(".text", secname) == 0)
-			maps[ARM_SEC_CORE].txt_sec = s;
-		else if (strcmp(".exit.text", secname) == 0)
-			maps[ARM_SEC_EXIT].txt_sec = s;
-		else if (strcmp(".text.unlikely", secname) == 0)
-			maps[ARM_SEC_UNLIKELY].txt_sec = s;
-		else if (strcmp(".text.hot", secname) == 0)
-			maps[ARM_SEC_HOT].txt_sec = s;
-	}
+		if (!strcmp(".ARM.exidx", secname))
+			txtname = ".text";
+		else
+			txtname = secname + strlen(".ARM.exidx");
+		txt_sec = find_mod_section(hdr, sechdrs, txtname);
+
+		if (txt_sec) {
+			struct unwind_table *table =
+				unwind_table_add(s->sh_addr,
+						s->sh_size,
+						txt_sec->sh_addr,
+						txt_sec->sh_size);
+
+			list_add(&table->mod_list, unwind_list);
 
-	for (i = 0; i < ARM_SEC_MAX; i++)
-		if (maps[i].unw_sec && maps[i].txt_sec)
-			mod->arch.unwind[i] =
-				unwind_table_add(maps[i].unw_sec->sh_addr,
-					         maps[i].unw_sec->sh_size,
-					         maps[i].txt_sec->sh_addr,
-					         maps[i].txt_sec->sh_size);
+			/* save init table for module_arch_freeing_init */
+			if (strcmp(".ARM.exidx.init.text", secname) == 0)
+				mod->arch.init_table = table;
+		}
+	}
 #endif
 #ifdef CONFIG_ARM_PATCH_PHYS_VIRT
 	s = find_mod_section(hdr, sechdrs, ".pv_table");
@@ -429,19 +513,27 @@ void
 module_arch_cleanup(struct module *mod)
 {
 #ifdef CONFIG_ARM_UNWIND
-	int i;
+	struct unwind_table *tmp;
+	struct unwind_table *n;
 
-	for (i = 0; i < ARM_SEC_MAX; i++) {
-		unwind_table_del(mod->arch.unwind[i]);
-		mod->arch.unwind[i] = NULL;
+	list_for_each_entry_safe(tmp, n,
+			&mod->arch.unwind_list, mod_list) {
+		list_del(&tmp->mod_list);
+		unwind_table_del(tmp);
 	}
+	mod->arch.init_table = NULL;
 #endif
 }
 
 void __weak module_arch_freeing_init(struct module *mod)
 {
 #ifdef CONFIG_ARM_UNWIND
-	unwind_table_del(mod->arch.unwind[ARM_SEC_INIT]);
-	mod->arch.unwind[ARM_SEC_INIT] = NULL;
+	struct unwind_table *init = mod->arch.init_table;
+
+	if (init) {
+		mod->arch.init_table = NULL;
+		list_del(&init->mod_list);
+		unwind_table_del(init);
+	}
 #endif
 }
diff --git a/arch/arm/kernel/perf_callchain.c b/arch/arm/kernel/perf_callchain.c
index 3b69a76d341e..bc6b246ab55e 100644
--- a/arch/arm/kernel/perf_callchain.c
+++ b/arch/arm/kernel/perf_callchain.c
@@ -64,11 +64,6 @@ perf_callchain_user(struct perf_callchain_entry_ctx *entry, struct pt_regs *regs
 {
 	struct frame_tail __user *tail;
 
-	if (perf_guest_cbs && perf_guest_cbs->is_in_guest()) {
-		/* We don't support guest os callchain now */
-		return;
-	}
-
 	perf_callchain_store(entry, regs->ARM_pc);
 
 	if (!current->mm)
@@ -100,20 +95,12 @@ perf_callchain_kernel(struct perf_callchain_entry_ctx *entry, struct pt_regs *re
 {
 	struct stackframe fr;
 
-	if (perf_guest_cbs && perf_guest_cbs->is_in_guest()) {
-		/* We don't support guest os callchain now */
-		return;
-	}
-
 	arm_get_current_stackframe(regs, &fr);
 	walk_stackframe(&fr, callchain_trace, entry);
 }
 
 unsigned long perf_instruction_pointer(struct pt_regs *regs)
 {
-	if (perf_guest_cbs && perf_guest_cbs->is_in_guest())
-		return perf_guest_cbs->get_guest_ip();
-
 	return instruction_pointer(regs);
 }
 
@@ -121,17 +108,10 @@ unsigned long perf_misc_flags(struct pt_regs *regs)
 {
 	int misc = 0;
 
-	if (perf_guest_cbs && perf_guest_cbs->is_in_guest()) {
-		if (perf_guest_cbs->is_user_mode())
-			misc |= PERF_RECORD_MISC_GUEST_USER;
-		else
-			misc |= PERF_RECORD_MISC_GUEST_KERNEL;
-	} else {
-		if (user_mode(regs))
-			misc |= PERF_RECORD_MISC_USER;
-		else
-			misc |= PERF_RECORD_MISC_KERNEL;
-	}
+	if (user_mode(regs))
+		misc |= PERF_RECORD_MISC_USER;
+	else
+		misc |= PERF_RECORD_MISC_KERNEL;
 
 	return misc;
 }
diff --git a/arch/arm/kernel/process.c b/arch/arm/kernel/process.c
index d47159f3791c..a2b31d91a1b6 100644
--- a/arch/arm/kernel/process.c
+++ b/arch/arm/kernel/process.c
@@ -36,7 +36,7 @@
 
 #include "signal.h"
 
-#ifdef CONFIG_CURRENT_POINTER_IN_TPIDRURO
+#if defined(CONFIG_CURRENT_POINTER_IN_TPIDRURO) || defined(CONFIG_SMP)
 DEFINE_PER_CPU(struct task_struct *, __entry_task);
 #endif
 
@@ -46,6 +46,11 @@ unsigned long __stack_chk_guard __read_mostly;
 EXPORT_SYMBOL(__stack_chk_guard);
 #endif
 
+#ifndef CONFIG_CURRENT_POINTER_IN_TPIDRURO
+asmlinkage struct task_struct *__current;
+EXPORT_SYMBOL(__current);
+#endif
+
 static const char *processor_modes[] __maybe_unused = {
   "USER_26", "FIQ_26" , "IRQ_26" , "SVC_26" , "UK4_26" , "UK5_26" , "UK6_26" , "UK7_26" ,
   "UK8_26" , "UK9_26" , "UK10_26", "UK11_26", "UK12_26", "UK13_26", "UK14_26", "UK15_26",
@@ -196,7 +201,7 @@ void __show_regs(struct pt_regs *regs)
 void show_regs(struct pt_regs * regs)
 {
 	__show_regs(regs);
-	dump_stack();
+	dump_backtrace(regs, NULL, KERN_DEFAULT);
 }
 
 ATOMIC_NOTIFIER_HEAD(thread_notify_head);
@@ -227,15 +232,13 @@ void flush_thread(void)
 	thread_notify(THREAD_NOTIFY_FLUSH, thread);
 }
 
-void release_thread(struct task_struct *dead_task)
-{
-}
-
 asmlinkage void ret_from_fork(void) __asm__("ret_from_fork");
 
-int copy_thread(unsigned long clone_flags, unsigned long stack_start,
-		unsigned long stk_sz, struct task_struct *p, unsigned long tls)
+int copy_thread(struct task_struct *p, const struct kernel_clone_args *args)
 {
+	unsigned long clone_flags = args->flags;
+	unsigned long stack_start = args->stack;
+	unsigned long tls = args->tls;
 	struct thread_info *thread = task_thread_info(p);
 	struct pt_regs *childregs = task_pt_regs(p);
 
@@ -251,15 +254,15 @@ int copy_thread(unsigned long clone_flags, unsigned long stack_start,
 	thread->cpu_domain = get_domain();
 #endif
 
-	if (likely(!(p->flags & (PF_KTHREAD | PF_IO_WORKER)))) {
+	if (likely(!args->fn)) {
 		*childregs = *current_pt_regs();
 		childregs->ARM_r0 = 0;
 		if (stack_start)
 			childregs->ARM_sp = stack_start;
 	} else {
 		memset(childregs, 0, sizeof(struct pt_regs));
-		thread->cpu_context.r4 = stk_sz;
-		thread->cpu_context.r5 = stack_start;
+		thread->cpu_context.r4 = (unsigned long)args->fn_arg;
+		thread->cpu_context.r5 = (unsigned long)args->fn;
 		childregs->ARM_cpsr = SVC_MODE;
 	}
 	thread->cpu_context.pc = (unsigned long)ret_from_fork;
@@ -368,7 +371,7 @@ static unsigned long sigpage_addr(const struct mm_struct *mm,
 
 	slots = ((last - first) >> PAGE_SHIFT) + 1;
 
-	offset = get_random_int() % slots;
+	offset = prandom_u32_max(slots);
 
 	addr = first + (offset << PAGE_SHIFT);
 
diff --git a/arch/arm/kernel/ptrace.c b/arch/arm/kernel/ptrace.c
index 43b963ea4a0e..bfe88c6e60d5 100644
--- a/arch/arm/kernel/ptrace.c
+++ b/arch/arm/kernel/ptrace.c
@@ -22,7 +22,6 @@
 #include <linux/hw_breakpoint.h>
 #include <linux/regset.h>
 #include <linux/audit.h>
-#include <linux/tracehook.h>
 #include <linux/unistd.h>
 
 #include <asm/syscall.h>
@@ -831,8 +830,7 @@ enum ptrace_syscall_dir {
 	PTRACE_SYSCALL_EXIT,
 };
 
-static void tracehook_report_syscall(struct pt_regs *regs,
-				    enum ptrace_syscall_dir dir)
+static void report_syscall(struct pt_regs *regs, enum ptrace_syscall_dir dir)
 {
 	unsigned long ip;
 
@@ -844,8 +842,8 @@ static void tracehook_report_syscall(struct pt_regs *regs,
 	regs->ARM_ip = dir;
 
 	if (dir == PTRACE_SYSCALL_EXIT)
-		tracehook_report_syscall_exit(regs, 0);
-	else if (tracehook_report_syscall_entry(regs))
+		ptrace_report_syscall_exit(regs, 0);
+	else if (ptrace_report_syscall_entry(regs))
 		current_thread_info()->abi_syscall = -1;
 
 	regs->ARM_ip = ip;
@@ -856,7 +854,7 @@ asmlinkage int syscall_trace_enter(struct pt_regs *regs)
 	int scno;
 
 	if (test_thread_flag(TIF_SYSCALL_TRACE))
-		tracehook_report_syscall(regs, PTRACE_SYSCALL_ENTER);
+		report_syscall(regs, PTRACE_SYSCALL_ENTER);
 
 	/* Do seccomp after ptrace; syscall may have changed. */
 #ifdef CONFIG_HAVE_ARCH_SECCOMP_FILTER
@@ -897,5 +895,5 @@ asmlinkage void syscall_trace_exit(struct pt_regs *regs)
 		trace_sys_exit(regs, regs_return_value(regs));
 
 	if (test_thread_flag(TIF_SYSCALL_TRACE))
-		tracehook_report_syscall(regs, PTRACE_SYSCALL_EXIT);
+		report_syscall(regs, PTRACE_SYSCALL_EXIT);
 }
diff --git a/arch/arm/kernel/reboot.c b/arch/arm/kernel/reboot.c
index 3044fcb8d073..3f0d5c3dae11 100644
--- a/arch/arm/kernel/reboot.c
+++ b/arch/arm/kernel/reboot.c
@@ -10,6 +10,7 @@
 #include <asm/cacheflush.h>
 #include <asm/idmap.h>
 #include <asm/virt.h>
+#include <asm/system_misc.h>
 
 #include "reboot.h"
 
@@ -116,9 +117,7 @@ void machine_power_off(void)
 {
 	local_irq_disable();
 	smp_send_stop();
-
-	if (pm_power_off)
-		pm_power_off();
+	do_kernel_power_off();
 }
 
 /*
diff --git a/arch/arm/kernel/return_address.c b/arch/arm/kernel/return_address.c
index 00c11579406c..38f1ea9c724d 100644
--- a/arch/arm/kernel/return_address.c
+++ b/arch/arm/kernel/return_address.c
@@ -41,11 +41,13 @@ void *return_address(unsigned int level)
 	frame.fp = (unsigned long)__builtin_frame_address(0);
 	frame.sp = current_stack_pointer;
 	frame.lr = (unsigned long)__builtin_return_address(0);
-	frame.pc = (unsigned long)return_address;
+here:
+	frame.pc = (unsigned long)&&here;
 #ifdef CONFIG_KRETPROBES
 	frame.kr_cur = NULL;
 	frame.tsk = current;
 #endif
+	frame.ex_frame = false;
 
 	walk_stackframe(&frame, save_return_addr, &data);
 
diff --git a/arch/arm/kernel/setup.c b/arch/arm/kernel/setup.c
index 284a80c0b6e1..cb88c6e69377 100644
--- a/arch/arm/kernel/setup.c
+++ b/arch/arm/kernel/setup.c
@@ -141,10 +141,10 @@ EXPORT_SYMBOL(outer_cache);
 int __cpu_architecture __read_mostly = CPU_ARCH_UNKNOWN;
 
 struct stack {
-	u32 irq[3];
-	u32 abt[3];
-	u32 und[3];
-	u32 fiq[3];
+	u32 irq[4];
+	u32 abt[4];
+	u32 und[4];
+	u32 fiq[4];
 } ____cacheline_aligned;
 
 #ifndef CONFIG_CPU_V7M
@@ -1004,7 +1004,8 @@ static void __init reserve_crashkernel(void)
 	total_mem = get_total_mem();
 	ret = parse_crashkernel(boot_command_line, total_mem,
 				&crash_size, &crash_base);
-	if (ret)
+	/* invalid value specified or crashkernel=0 */
+	if (ret || !crash_size)
 		return;
 
 	if (crash_base <= 0) {
@@ -1140,7 +1141,7 @@ void __init setup_arch(char **cmdline_p)
 #endif
 	setup_dma_zone(mdesc);
 	xen_early_init();
-	efi_init();
+	arm_efi_init();
 	/*
 	 * Make sure the calculation for lowmem/highmem is set appropriately
 	 * before reserving/allocating any memory
diff --git a/arch/arm/kernel/signal.c b/arch/arm/kernel/signal.c
index a41e27ace391..e07f359254c3 100644
--- a/arch/arm/kernel/signal.c
+++ b/arch/arm/kernel/signal.c
@@ -9,7 +9,7 @@
 #include <linux/signal.h>
 #include <linux/personality.h>
 #include <linux/uaccess.h>
-#include <linux/tracehook.h>
+#include <linux/resume_user_mode.h>
 #include <linux/uprobes.h>
 #include <linux/syscalls.h>
 
@@ -627,11 +627,11 @@ do_work_pending(struct pt_regs *regs, unsigned int thread_flags, int syscall)
 			} else if (thread_flags & _TIF_UPROBE) {
 				uprobe_notify_resume(regs);
 			} else {
-				tracehook_notify_resume(regs);
+				resume_user_mode_work(regs);
 			}
 		}
 		local_irq_disable();
-		thread_flags = current_thread_info()->flags;
+		thread_flags = read_thread_flags();
 	} while (thread_flags & _TIF_WORK_MASK);
 	return 0;
 }
@@ -655,7 +655,7 @@ struct page *get_signal_page(void)
 		 PAGE_SIZE / sizeof(u32));
 
 	/* Give the signal return code some randomness */
-	offset = 0x200 + (get_random_int() & 0x7fc);
+	offset = 0x200 + (get_random_u16() & 0x7fc);
 	signal_return_offset = offset;
 
 	/* Copy signal return handlers into the page */
@@ -708,6 +708,7 @@ static_assert(offsetof(siginfo_t, si_upper)	== 0x18);
 static_assert(offsetof(siginfo_t, si_pkey)	== 0x14);
 static_assert(offsetof(siginfo_t, si_perf_data)	== 0x10);
 static_assert(offsetof(siginfo_t, si_perf_type)	== 0x14);
+static_assert(offsetof(siginfo_t, si_perf_flags) == 0x18);
 static_assert(offsetof(siginfo_t, si_band)	== 0x0c);
 static_assert(offsetof(siginfo_t, si_fd)	== 0x10);
 static_assert(offsetof(siginfo_t, si_call_addr)	== 0x0c);
diff --git a/arch/arm/kernel/sleep.S b/arch/arm/kernel/sleep.S
index 43077e11dafd..a86a1d4f3461 100644
--- a/arch/arm/kernel/sleep.S
+++ b/arch/arm/kernel/sleep.S
@@ -67,6 +67,12 @@ ENTRY(__cpu_suspend)
 	ldr	r4, =cpu_suspend_size
 #endif
 	mov	r5, sp			@ current virtual SP
+#ifdef CONFIG_VMAP_STACK
+	@ Run the suspend code from the overflow stack so we don't have to rely
+	@ on vmalloc-to-phys conversions anywhere in the arch suspend code.
+	@ The original SP value captured in R5 will be restored on the way out.
+	ldr_this_cpu sp, overflow_stack_ptr, r6, r7
+#endif
 	add	r4, r4, #12		@ Space for pgd, virt sp, phys resume fn
 	sub	sp, sp, r4		@ allocate CPU state on stack
 	ldr	r3, =sleep_save_sp
@@ -113,6 +119,13 @@ ENTRY(cpu_resume_mmu)
 ENDPROC(cpu_resume_mmu)
 	.popsection
 cpu_resume_after_mmu:
+#if defined(CONFIG_VMAP_STACK) && !defined(CONFIG_ARM_LPAE)
+	@ Before using the vmap'ed stack, we have to switch to swapper_pg_dir
+	@ as the ID map does not cover the vmalloc region.
+	mrc	p15, 0, ip, c2, c0, 1	@ read TTBR1
+	mcr	p15, 0, ip, c2, c0, 0	@ set TTBR0
+	instr_sync
+#endif
 	bl	cpu_init		@ restore the und/abt/irq banked regs
 	mov	r0, #0			@ return zero on success
 	ldmfd	sp!, {r4 - r11, pc}
diff --git a/arch/arm/kernel/smp.c b/arch/arm/kernel/smp.c
index cde5b6d8bac5..978db2d96b44 100644
--- a/arch/arm/kernel/smp.c
+++ b/arch/arm/kernel/smp.c
@@ -154,9 +154,6 @@ int __cpu_up(unsigned int cpu, struct task_struct *idle)
 	secondary_data.swapper_pg_dir = get_arch_pgd(swapper_pg_dir);
 #endif
 	secondary_data.task = idle;
-	if (IS_ENABLED(CONFIG_THREAD_INFO_IN_TASK))
-		task_thread_info(idle)->cpu = cpu;
-
 	sync_cache_w(&secondary_data);
 
 	/*
@@ -403,6 +400,12 @@ static void smp_store_cpu_info(unsigned int cpuid)
 	check_cpu_icache_size(cpuid);
 }
 
+static void set_current(struct task_struct *cur)
+{
+	/* Set TPIDRURO */
+	asm("mcr p15, 0, %0, c13, c0, 3" :: "r"(cur) : "memory");
+}
+
 /*
  * This is the secondary CPU boot entry.  We're using this CPUs
  * idle thread stack, but a set of temporary page tables.
@@ -631,11 +634,6 @@ static void ipi_complete(unsigned int cpu)
 /*
  * Main handler for inter-processor interrupts
  */
-asmlinkage void __exception_irq_entry do_IPI(int ipinr, struct pt_regs *regs)
-{
-	handle_IPI(ipinr, regs);
-}
-
 static void do_handle_IPI(int ipinr)
 {
 	unsigned int cpu = smp_processor_id();
@@ -789,14 +787,6 @@ void panic_smp_self_stop(void)
 		cpu_relax();
 }
 
-/*
- * not supported here
- */
-int setup_profiling_timer(unsigned int multiplier)
-{
-	return -EINVAL;
-}
-
 #ifdef CONFIG_CPU_FREQ
 
 static DEFINE_PER_CPU(unsigned long, l_p_j_ref);
diff --git a/arch/arm/kernel/spectre.c b/arch/arm/kernel/spectre.c
new file mode 100644
index 000000000000..0dcefc36fb7a
--- /dev/null
+++ b/arch/arm/kernel/spectre.c
@@ -0,0 +1,71 @@
+// SPDX-License-Identifier: GPL-2.0-only
+#include <linux/bpf.h>
+#include <linux/cpu.h>
+#include <linux/device.h>
+
+#include <asm/spectre.h>
+
+static bool _unprivileged_ebpf_enabled(void)
+{
+#ifdef CONFIG_BPF_SYSCALL
+	return !sysctl_unprivileged_bpf_disabled;
+#else
+	return false;
+#endif
+}
+
+ssize_t cpu_show_spectre_v1(struct device *dev, struct device_attribute *attr,
+			    char *buf)
+{
+	return sprintf(buf, "Mitigation: __user pointer sanitization\n");
+}
+
+static unsigned int spectre_v2_state;
+static unsigned int spectre_v2_methods;
+
+void spectre_v2_update_state(unsigned int state, unsigned int method)
+{
+	if (state > spectre_v2_state)
+		spectre_v2_state = state;
+	spectre_v2_methods |= method;
+}
+
+ssize_t cpu_show_spectre_v2(struct device *dev, struct device_attribute *attr,
+			    char *buf)
+{
+	const char *method;
+
+	if (spectre_v2_state == SPECTRE_UNAFFECTED)
+		return sprintf(buf, "%s\n", "Not affected");
+
+	if (spectre_v2_state != SPECTRE_MITIGATED)
+		return sprintf(buf, "%s\n", "Vulnerable");
+
+	if (_unprivileged_ebpf_enabled())
+		return sprintf(buf, "Vulnerable: Unprivileged eBPF enabled\n");
+
+	switch (spectre_v2_methods) {
+	case SPECTRE_V2_METHOD_BPIALL:
+		method = "Branch predictor hardening";
+		break;
+
+	case SPECTRE_V2_METHOD_ICIALLU:
+		method = "I-cache invalidation";
+		break;
+
+	case SPECTRE_V2_METHOD_SMC:
+	case SPECTRE_V2_METHOD_HVC:
+		method = "Firmware call";
+		break;
+
+	case SPECTRE_V2_METHOD_LOOP8:
+		method = "History overwrite";
+		break;
+
+	default:
+		method = "Multiple mitigations";
+		break;
+	}
+
+	return sprintf(buf, "Mitigation: %s\n", method);
+}
diff --git a/arch/arm/kernel/stacktrace.c b/arch/arm/kernel/stacktrace.c
index 75e905508f27..85443b5d1922 100644
--- a/arch/arm/kernel/stacktrace.c
+++ b/arch/arm/kernel/stacktrace.c
@@ -9,6 +9,8 @@
 #include <asm/stacktrace.h>
 #include <asm/traps.h>
 
+#include "reboot.h"
+
 #if defined(CONFIG_FRAME_POINTER) && !defined(CONFIG_ARM_UNWIND)
 /*
  * Unwind the current stack frame and store the new register values in the
@@ -39,32 +41,77 @@
  * Note that with framepointer enabled, even the leaf functions have the same
  * prologue and epilogue, therefore we can ignore the LR value in this case.
  */
-int notrace unwind_frame(struct stackframe *frame)
+
+extern unsigned long call_with_stack_end;
+
+static int frame_pointer_check(struct stackframe *frame)
 {
 	unsigned long high, low;
 	unsigned long fp = frame->fp;
+	unsigned long pc = frame->pc;
+
+	/*
+	 * call_with_stack() is the only place we allow SP to jump from one
+	 * stack to another, with FP and SP pointing to different stacks,
+	 * skipping the FP boundary check at this point.
+	 */
+	if (pc >= (unsigned long)&call_with_stack &&
+			pc < (unsigned long)&call_with_stack_end)
+		return 0;
 
 	/* only go to a higher address on the stack */
 	low = frame->sp;
 	high = ALIGN(low, THREAD_SIZE);
 
-#ifdef CONFIG_CC_IS_CLANG
 	/* check current frame pointer is within bounds */
+#ifdef CONFIG_CC_IS_CLANG
 	if (fp < low + 4 || fp > high - 4)
 		return -EINVAL;
-
-	frame->sp = frame->fp;
-	frame->fp = *(unsigned long *)(fp);
-	frame->pc = *(unsigned long *)(fp + 4);
 #else
-	/* check current frame pointer is within bounds */
 	if (fp < low + 12 || fp > high - 4)
 		return -EINVAL;
+#endif
+
+	return 0;
+}
+
+int notrace unwind_frame(struct stackframe *frame)
+{
+	unsigned long fp = frame->fp;
+
+	if (frame_pointer_check(frame))
+		return -EINVAL;
+
+	/*
+	 * When we unwind through an exception stack, include the saved PC
+	 * value into the stack trace.
+	 */
+	if (frame->ex_frame) {
+		struct pt_regs *regs = (struct pt_regs *)frame->sp;
+
+		/*
+		 * We check that 'regs + sizeof(struct pt_regs)' (that is,
+		 * &regs[1]) does not exceed the bottom of the stack to avoid
+		 * accessing data outside the task's stack. This may happen
+		 * when frame->ex_frame is a false positive.
+		 */
+		if ((unsigned long)&regs[1] > ALIGN(frame->sp, THREAD_SIZE))
+			return -EINVAL;
+
+		frame->pc = regs->ARM_pc;
+		frame->ex_frame = false;
+		return 0;
+	}
 
 	/* restore the registers from the stack frame */
-	frame->fp = *(unsigned long *)(fp - 12);
-	frame->sp = *(unsigned long *)(fp - 8);
-	frame->pc = *(unsigned long *)(fp - 4);
+#ifdef CONFIG_CC_IS_CLANG
+	frame->sp = frame->fp;
+	frame->fp = READ_ONCE_NOCHECK(*(unsigned long *)(fp));
+	frame->pc = READ_ONCE_NOCHECK(*(unsigned long *)(fp + 4));
+#else
+	frame->fp = READ_ONCE_NOCHECK(*(unsigned long *)(fp - 12));
+	frame->sp = READ_ONCE_NOCHECK(*(unsigned long *)(fp - 8));
+	frame->pc = READ_ONCE_NOCHECK(*(unsigned long *)(fp - 4));
 #endif
 #ifdef CONFIG_KRETPROBES
 	if (is_kretprobe_trampoline(frame->pc))
@@ -72,6 +119,9 @@ int notrace unwind_frame(struct stackframe *frame)
 					(void *)frame->fp, &frame->kr_cur);
 #endif
 
+	if (in_entry_text(frame->pc))
+		frame->ex_frame = true;
+
 	return 0;
 }
 #endif
@@ -102,7 +152,6 @@ static int save_trace(struct stackframe *frame, void *d)
 {
 	struct stack_trace_data *data = d;
 	struct stack_trace *trace = data->trace;
-	struct pt_regs *regs;
 	unsigned long addr = frame->pc;
 
 	if (data->no_sched_functions && in_sched_functions(addr))
@@ -113,19 +162,6 @@ static int save_trace(struct stackframe *frame, void *d)
 	}
 
 	trace->entries[trace->nr_entries++] = addr;
-
-	if (trace->nr_entries >= trace->max_entries)
-		return 1;
-
-	if (!in_entry_text(frame->pc))
-		return 0;
-
-	regs = (struct pt_regs *)frame->sp;
-	if ((unsigned long)&regs[1] > ALIGN(frame->sp, THREAD_SIZE))
-		return 0;
-
-	trace->entries[trace->nr_entries++] = regs->ARM_pc;
-
 	return trace->nr_entries >= trace->max_entries;
 }
 
@@ -160,12 +196,16 @@ static noinline void __save_stack_trace(struct task_struct *tsk,
 		frame.fp = (unsigned long)__builtin_frame_address(0);
 		frame.sp = current_stack_pointer;
 		frame.lr = (unsigned long)__builtin_return_address(0);
-		frame.pc = (unsigned long)__save_stack_trace;
+here:
+		frame.pc = (unsigned long)&&here;
 	}
 #ifdef CONFIG_KRETPROBES
 	frame.kr_cur = NULL;
 	frame.tsk = tsk;
 #endif
+#ifdef CONFIG_UNWINDER_FRAME_POINTER
+	frame.ex_frame = false;
+#endif
 
 	walk_stackframe(&frame, save_trace, &data);
 }
@@ -187,6 +227,9 @@ void save_stack_trace_regs(struct pt_regs *regs, struct stack_trace *trace)
 	frame.kr_cur = NULL;
 	frame.tsk = current;
 #endif
+#ifdef CONFIG_UNWINDER_FRAME_POINTER
+	frame.ex_frame = in_entry_text(frame.pc);
+#endif
 
 	walk_stackframe(&frame, save_trace, &data);
 }
diff --git a/arch/arm/kernel/swp_emulate.c b/arch/arm/kernel/swp_emulate.c
index 6166ba38bf99..b74bfcf94fb1 100644
--- a/arch/arm/kernel/swp_emulate.c
+++ b/arch/arm/kernel/swp_emulate.c
@@ -195,7 +195,7 @@ static int swp_handler(struct pt_regs *regs, unsigned int instr)
 		 destreg, EXTRACT_REG_NUM(instr, RT2_OFFSET), data);
 
 	/* Check access in reasonable access range for both SWP and SWPB */
-	if (!access_ok((address & ~3), 4)) {
+	if (!access_ok((void __user *)(address & ~3), 4)) {
 		pr_debug("SWP{B} emulation: access to %p not allowed!\n",
 			 (void *)address);
 		res = -EFAULT;
diff --git a/arch/arm/kernel/traps.c b/arch/arm/kernel/traps.c
index 195dff58bafc..20b2db6dcd1c 100644
--- a/arch/arm/kernel/traps.c
+++ b/arch/arm/kernel/traps.c
@@ -30,11 +30,13 @@
 #include <linux/atomic.h>
 #include <asm/cacheflush.h>
 #include <asm/exception.h>
+#include <asm/spectre.h>
 #include <asm/unistd.h>
 #include <asm/traps.h>
 #include <asm/ptrace.h>
 #include <asm/unwind.h>
 #include <asm/tls.h>
+#include <asm/stacktrace.h>
 #include <asm/system_misc.h>
 #include <asm/opcodes.h>
 
@@ -60,19 +62,32 @@ static int __init user_debug_setup(char *str)
 __setup("user_debug=", user_debug_setup);
 #endif
 
-static void dump_mem(const char *, const char *, unsigned long, unsigned long);
-
 void dump_backtrace_entry(unsigned long where, unsigned long from,
 			  unsigned long frame, const char *loglvl)
 {
 	unsigned long end = frame + 4 + sizeof(struct pt_regs);
 
-#ifdef CONFIG_KALLSYMS
+	if (IS_ENABLED(CONFIG_UNWINDER_FRAME_POINTER) &&
+	    IS_ENABLED(CONFIG_CC_IS_GCC) &&
+	    end > ALIGN(frame, THREAD_SIZE)) {
+		/*
+		 * If we are walking past the end of the stack, it may be due
+		 * to the fact that we are on an IRQ or overflow stack. In this
+		 * case, we can load the address of the other stack from the
+		 * frame record.
+		 */
+		frame = ((unsigned long *)frame)[-2] - 4;
+		end = frame + 4 + sizeof(struct pt_regs);
+	}
+
+#ifndef CONFIG_KALLSYMS
+	printk("%sFunction entered at [<%08lx>] from [<%08lx>]\n",
+		loglvl, where, from);
+#elif defined CONFIG_BACKTRACE_VERBOSE
 	printk("%s[<%08lx>] (%ps) from [<%08lx>] (%pS)\n",
 		loglvl, where, (void *)where, from, (void *)from);
 #else
-	printk("%sFunction entered at [<%08lx>] from [<%08lx>]\n",
-		loglvl, where, from);
+	printk("%s %ps from %pS\n", loglvl, (void *)where, (void *)from);
 #endif
 
 	if (in_entry_text(from) && end <= ALIGN(frame, THREAD_SIZE))
@@ -108,7 +123,8 @@ void dump_backtrace_stm(u32 *stack, u32 instruction, const char *loglvl)
 static int verify_stack(unsigned long sp)
 {
 	if (sp < PAGE_OFFSET ||
-	    (sp > (unsigned long)high_memory && high_memory != NULL))
+	    (!IS_ENABLED(CONFIG_VMAP_STACK) &&
+	     sp > (unsigned long)high_memory && high_memory != NULL))
 		return -EFAULT;
 
 	return 0;
@@ -118,8 +134,8 @@ static int verify_stack(unsigned long sp)
 /*
  * Dump out the contents of some memory nicely...
  */
-static void dump_mem(const char *lvl, const char *str, unsigned long bottom,
-		     unsigned long top)
+void dump_mem(const char *lvl, const char *str, unsigned long bottom,
+	      unsigned long top)
 {
 	unsigned long first;
 	int i;
@@ -189,14 +205,14 @@ static void dump_instr(const char *lvl, struct pt_regs *regs)
 }
 
 #ifdef CONFIG_ARM_UNWIND
-static inline void dump_backtrace(struct pt_regs *regs, struct task_struct *tsk,
-				  const char *loglvl)
+void dump_backtrace(struct pt_regs *regs, struct task_struct *tsk,
+		    const char *loglvl)
 {
 	unwind_backtrace(regs, tsk, loglvl);
 }
 #else
-static void dump_backtrace(struct pt_regs *regs, struct task_struct *tsk,
-			   const char *loglvl)
+void dump_backtrace(struct pt_regs *regs, struct task_struct *tsk,
+		    const char *loglvl)
 {
 	unsigned int fp, mode;
 	int ok = 1;
@@ -278,7 +294,8 @@ static int __die(const char *str, int err, struct pt_regs *regs)
 
 	if (!user_mode(regs) || in_interrupt()) {
 		dump_mem(KERN_EMERG, "Stack: ", regs->ARM_sp,
-			 THREAD_SIZE + (unsigned long)task_stack_page(tsk));
+			 ALIGN(regs->ARM_sp - THREAD_SIZE, THREAD_ALIGN)
+			 + THREAD_SIZE);
 		dump_backtrace(regs, tsk, KERN_EMERG);
 		dump_instr(KERN_EMERG, regs);
 	}
@@ -333,7 +350,7 @@ static void oops_end(unsigned long flags, struct pt_regs *regs, int signr)
 	if (panic_on_oops)
 		panic("Fatal exception");
 	if (signr)
-		do_exit(signr);
+		make_task_dead(signr);
 }
 
 /*
@@ -470,7 +487,7 @@ asmlinkage void do_undefinstr(struct pt_regs *regs)
 die_sig:
 #ifdef CONFIG_DEBUG_USER
 	if (user_debug & UDBG_UNDEFINED) {
-		pr_info("%s (%d): undefined instruction: pc=%p\n",
+		pr_info("%s (%d): undefined instruction: pc=%px\n",
 			current->comm, task_pid_nr(current), pc);
 		__show_regs(regs);
 		dump_instr(KERN_INFO, regs);
@@ -574,7 +591,7 @@ do_cache_op(unsigned long start, unsigned long end, int flags)
 	if (end < start || flags)
 		return -EINVAL;
 
-	if (!access_ok(start, end - start))
+	if (!access_ok((void __user *)start, end - start))
 		return -EFAULT;
 
 	return __do_cache_op(start, end);
@@ -787,10 +804,59 @@ static inline void __init kuser_init(void *vectors)
 }
 #endif
 
+#ifndef CONFIG_CPU_V7M
+static void copy_from_lma(void *vma, void *lma_start, void *lma_end)
+{
+	memcpy(vma, lma_start, lma_end - lma_start);
+}
+
+static void flush_vectors(void *vma, size_t offset, size_t size)
+{
+	unsigned long start = (unsigned long)vma + offset;
+	unsigned long end = start + size;
+
+	flush_icache_range(start, end);
+}
+
+#ifdef CONFIG_HARDEN_BRANCH_HISTORY
+int spectre_bhb_update_vectors(unsigned int method)
+{
+	extern char __vectors_bhb_bpiall_start[], __vectors_bhb_bpiall_end[];
+	extern char __vectors_bhb_loop8_start[], __vectors_bhb_loop8_end[];
+	void *vec_start, *vec_end;
+
+	if (system_state >= SYSTEM_FREEING_INITMEM) {
+		pr_err("CPU%u: Spectre BHB workaround too late - system vulnerable\n",
+		       smp_processor_id());
+		return SPECTRE_VULNERABLE;
+	}
+
+	switch (method) {
+	case SPECTRE_V2_METHOD_LOOP8:
+		vec_start = __vectors_bhb_loop8_start;
+		vec_end = __vectors_bhb_loop8_end;
+		break;
+
+	case SPECTRE_V2_METHOD_BPIALL:
+		vec_start = __vectors_bhb_bpiall_start;
+		vec_end = __vectors_bhb_bpiall_end;
+		break;
+
+	default:
+		pr_err("CPU%u: unknown Spectre BHB state %d\n",
+		       smp_processor_id(), method);
+		return SPECTRE_VULNERABLE;
+	}
+
+	copy_from_lma(vectors_page, vec_start, vec_end);
+	flush_vectors(vectors_page, 0, vec_end - vec_start);
+
+	return SPECTRE_MITIGATED;
+}
+#endif
+
 void __init early_trap_init(void *vectors_base)
 {
-#ifndef CONFIG_CPU_V7M
-	unsigned long vectors = (unsigned long)vectors_base;
 	extern char __stubs_start[], __stubs_end[];
 	extern char __vectors_start[], __vectors_end[];
 	unsigned i;
@@ -811,17 +877,87 @@ void __init early_trap_init(void *vectors_base)
 	 * into the vector page, mapped at 0xffff0000, and ensure these
 	 * are visible to the instruction stream.
 	 */
-	memcpy((void *)vectors, __vectors_start, __vectors_end - __vectors_start);
-	memcpy((void *)vectors + 0x1000, __stubs_start, __stubs_end - __stubs_start);
+	copy_from_lma(vectors_base, __vectors_start, __vectors_end);
+	copy_from_lma(vectors_base + 0x1000, __stubs_start, __stubs_end);
 
 	kuser_init(vectors_base);
 
-	flush_icache_range(vectors, vectors + PAGE_SIZE * 2);
+	flush_vectors(vectors_base, 0, PAGE_SIZE * 2);
+}
 #else /* ifndef CONFIG_CPU_V7M */
+void __init early_trap_init(void *vectors_base)
+{
 	/*
 	 * on V7-M there is no need to copy the vector table to a dedicated
 	 * memory area. The address is configurable and so a table in the kernel
 	 * image can be used.
 	 */
+}
+#endif
+
+#ifdef CONFIG_VMAP_STACK
+
+DECLARE_PER_CPU(u8 *, irq_stack_ptr);
+
+asmlinkage DEFINE_PER_CPU(u8 *, overflow_stack_ptr);
+
+static int __init allocate_overflow_stacks(void)
+{
+	u8 *stack;
+	int cpu;
+
+	for_each_possible_cpu(cpu) {
+		stack = (u8 *)__get_free_page(GFP_KERNEL);
+		if (WARN_ON(!stack))
+			return -ENOMEM;
+		per_cpu(overflow_stack_ptr, cpu) = &stack[OVERFLOW_STACK_SIZE];
+	}
+	return 0;
+}
+early_initcall(allocate_overflow_stacks);
+
+asmlinkage void handle_bad_stack(struct pt_regs *regs)
+{
+	unsigned long tsk_stk = (unsigned long)current->stack;
+#ifdef CONFIG_IRQSTACKS
+	unsigned long irq_stk = (unsigned long)raw_cpu_read(irq_stack_ptr);
+#endif
+	unsigned long ovf_stk = (unsigned long)raw_cpu_read(overflow_stack_ptr);
+
+	console_verbose();
+	pr_emerg("Insufficient stack space to handle exception!");
+
+	pr_emerg("Task stack:     [0x%08lx..0x%08lx]\n",
+		 tsk_stk, tsk_stk + THREAD_SIZE);
+#ifdef CONFIG_IRQSTACKS
+	pr_emerg("IRQ stack:      [0x%08lx..0x%08lx]\n",
+		 irq_stk - THREAD_SIZE, irq_stk);
 #endif
+	pr_emerg("Overflow stack: [0x%08lx..0x%08lx]\n",
+		 ovf_stk - OVERFLOW_STACK_SIZE, ovf_stk);
+
+	die("kernel stack overflow", regs, 0);
 }
+
+#ifndef CONFIG_ARM_LPAE
+/*
+ * Normally, we rely on the logic in do_translation_fault() to update stale PMD
+ * entries covering the vmalloc space in a task's page tables when it first
+ * accesses the region in question. Unfortunately, this is not sufficient when
+ * the task stack resides in the vmalloc region, as do_translation_fault() is a
+ * C function that needs a stack to run.
+ *
+ * So we need to ensure that these PMD entries are up to date *before* the MM
+ * switch. As we already have some logic in the MM switch path that takes care
+ * of this, let's trigger it by bumping the counter every time the core vmalloc
+ * code modifies a PMD entry in the vmalloc region. Use release semantics on
+ * the store so that other CPUs observing the counter's new value are
+ * guaranteed to see the updated page table entries as well.
+ */
+void arch_sync_kernel_mappings(unsigned long start, unsigned long end)
+{
+	if (start < VMALLOC_END && end > VMALLOC_START)
+		atomic_inc_return_release(&init_mm.context.vmalloc_seq);
+}
+#endif
+#endif
diff --git a/arch/arm/kernel/unwind.c b/arch/arm/kernel/unwind.c
index 59fdf257bf8b..a37ea6c772cd 100644
--- a/arch/arm/kernel/unwind.c
+++ b/arch/arm/kernel/unwind.c
@@ -33,6 +33,8 @@
 #include <asm/traps.h>
 #include <asm/unwind.h>
 
+#include "reboot.h"
+
 /* Dummy functions to avoid linker complaints */
 void __aeabi_unwind_cpp_pr0(void)
 {
@@ -53,6 +55,7 @@ struct unwind_ctrl_block {
 	unsigned long vrs[16];		/* virtual register set */
 	const unsigned long *insn;	/* pointer to the current instructions word */
 	unsigned long sp_high;		/* highest value of sp allowed */
+	unsigned long *lr_addr;		/* address of LR value on the stack */
 	/*
 	 * 1 : check for stack overflow for each register pop.
 	 * 0 : save overhead if there is plenty of stack remaining.
@@ -237,6 +240,8 @@ static int unwind_pop_register(struct unwind_ctrl_block *ctrl,
 	 * from being tracked by KASAN.
 	 */
 	ctrl->vrs[reg] = READ_ONCE_NOCHECK(*(*vsp));
+	if (reg == 14)
+		ctrl->lr_addr = *vsp;
 	(*vsp)++;
 	return URC_OK;
 }
@@ -256,8 +261,9 @@ static int unwind_exec_pop_subset_r4_to_r13(struct unwind_ctrl_block *ctrl,
 		mask >>= 1;
 		reg++;
 	}
-	if (!load_sp)
+	if (!load_sp) {
 		ctrl->vrs[SP] = (unsigned long)vsp;
+	}
 
 	return URC_OK;
 }
@@ -313,9 +319,9 @@ static int unwind_exec_insn(struct unwind_ctrl_block *ctrl)
 
 	if ((insn & 0xc0) == 0x00)
 		ctrl->vrs[SP] += ((insn & 0x3f) << 2) + 4;
-	else if ((insn & 0xc0) == 0x40)
+	else if ((insn & 0xc0) == 0x40) {
 		ctrl->vrs[SP] -= ((insn & 0x3f) << 2) + 4;
-	else if ((insn & 0xf0) == 0x80) {
+	} else if ((insn & 0xf0) == 0x80) {
 		unsigned long mask;
 
 		insn = (insn << 8) | unwind_get_byte(ctrl);
@@ -330,9 +336,9 @@ static int unwind_exec_insn(struct unwind_ctrl_block *ctrl)
 		if (ret)
 			goto error;
 	} else if ((insn & 0xf0) == 0x90 &&
-		   (insn & 0x0d) != 0x0d)
+		   (insn & 0x0d) != 0x0d) {
 		ctrl->vrs[SP] = ctrl->vrs[insn & 0x0f];
-	else if ((insn & 0xf0) == 0xa0) {
+	} else if ((insn & 0xf0) == 0xa0) {
 		ret = unwind_exec_pop_r4_to_rN(ctrl, insn);
 		if (ret)
 			goto error;
@@ -375,23 +381,22 @@ error:
  */
 int unwind_frame(struct stackframe *frame)
 {
-	unsigned long low;
 	const struct unwind_idx *idx;
 	struct unwind_ctrl_block ctrl;
+	unsigned long sp_low;
 
 	/* store the highest address on the stack to avoid crossing it*/
-	low = frame->sp;
-	ctrl.sp_high = ALIGN(low, THREAD_SIZE);
+	sp_low = frame->sp;
+	ctrl.sp_high = ALIGN(sp_low - THREAD_SIZE, THREAD_ALIGN)
+		       + THREAD_SIZE;
 
 	pr_debug("%s(pc = %08lx lr = %08lx sp = %08lx)\n", __func__,
 		 frame->pc, frame->lr, frame->sp);
 
-	if (!kernel_text_address(frame->pc))
-		return -URC_FAILURE;
-
 	idx = unwind_find_idx(frame->pc);
 	if (!idx) {
-		pr_warn("unwind: Index not found %08lx\n", frame->pc);
+		if (frame->pc && kernel_text_address(frame->pc))
+			pr_warn("unwind: Index not found %08lx\n", frame->pc);
 		return -URC_FAILURE;
 	}
 
@@ -403,7 +408,20 @@ int unwind_frame(struct stackframe *frame)
 	if (idx->insn == 1)
 		/* can't unwind */
 		return -URC_FAILURE;
-	else if ((idx->insn & 0x80000000) == 0)
+	else if (frame->pc == prel31_to_addr(&idx->addr_offset)) {
+		/*
+		 * Unwinding is tricky when we're halfway through the prologue,
+		 * since the stack frame that the unwinder expects may not be
+		 * fully set up yet. However, one thing we do know for sure is
+		 * that if we are unwinding from the very first instruction of
+		 * a function, we are still effectively in the stack frame of
+		 * the caller, and the unwind info has no relevance yet.
+		 */
+		if (frame->pc == frame->lr)
+			return -URC_FAILURE;
+		frame->pc = frame->lr;
+		return URC_OK;
+	} else if ((idx->insn & 0x80000000) == 0)
 		/* prel31 to the unwind table */
 		ctrl.insn = (unsigned long *)prel31_to_addr(&idx->insn);
 	else if ((idx->insn & 0xff000000) == 0x80000000)
@@ -430,6 +448,16 @@ int unwind_frame(struct stackframe *frame)
 
 	ctrl.check_each_pop = 0;
 
+	if (prel31_to_addr(&idx->addr_offset) == (u32)&call_with_stack) {
+		/*
+		 * call_with_stack() is the only place where we permit SP to
+		 * jump from one stack to another, and since we know it is
+		 * guaranteed to happen, set up the SP bounds accordingly.
+		 */
+		sp_low = frame->fp;
+		ctrl.sp_high = ALIGN(frame->fp, THREAD_SIZE);
+	}
+
 	while (ctrl.entries > 0) {
 		int urc;
 		if ((ctrl.sp_high - ctrl.vrs[SP]) < sizeof(ctrl.vrs))
@@ -437,7 +465,7 @@ int unwind_frame(struct stackframe *frame)
 		urc = unwind_exec_insn(&ctrl);
 		if (urc < 0)
 			return urc;
-		if (ctrl.vrs[SP] < low || ctrl.vrs[SP] >= ctrl.sp_high)
+		if (ctrl.vrs[SP] < sp_low || ctrl.vrs[SP] > ctrl.sp_high)
 			return -URC_FAILURE;
 	}
 
@@ -452,6 +480,7 @@ int unwind_frame(struct stackframe *frame)
 	frame->sp = ctrl.vrs[SP];
 	frame->lr = ctrl.vrs[LR];
 	frame->pc = ctrl.vrs[PC];
+	frame->lr_addr = ctrl.lr_addr;
 
 	return URC_OK;
 }
@@ -475,7 +504,12 @@ void unwind_backtrace(struct pt_regs *regs, struct task_struct *tsk,
 		frame.fp = (unsigned long)__builtin_frame_address(0);
 		frame.sp = current_stack_pointer;
 		frame.lr = (unsigned long)__builtin_return_address(0);
-		frame.pc = (unsigned long)unwind_backtrace;
+		/* We are saving the stack and execution state at this
+		 * point, so we should ensure that frame.pc is within
+		 * this block of code.
+		 */
+here:
+		frame.pc = (unsigned long)&&here;
 	} else {
 		/* task blocked in __switch_to */
 		frame.fp = thread_saved_fp(tsk);
diff --git a/arch/arm/kernel/vmlinux.lds.S b/arch/arm/kernel/vmlinux.lds.S
index f02d617e3359..aa12b65a7fd6 100644
--- a/arch/arm/kernel/vmlinux.lds.S
+++ b/arch/arm/kernel/vmlinux.lds.S
@@ -138,12 +138,12 @@ SECTIONS
 #ifdef CONFIG_STRICT_KERNEL_RWX
 	. = ALIGN(1<<SECTION_SHIFT);
 #else
-	. = ALIGN(THREAD_SIZE);
+	. = ALIGN(THREAD_ALIGN);
 #endif
 	__init_end = .;
 
 	_sdata = .;
-	RW_DATA(L1_CACHE_BYTES, PAGE_SIZE, THREAD_SIZE)
+	RW_DATA(L1_CACHE_BYTES, PAGE_SIZE, THREAD_ALIGN)
 	_edata = .;
 
 	BSS_SECTION(0, 0, 0)
diff --git a/arch/arm/lib/backtrace-clang.S b/arch/arm/lib/backtrace-clang.S
index 5b2cdb1003e3..290c52a60fc6 100644
--- a/arch/arm/lib/backtrace-clang.S
+++ b/arch/arm/lib/backtrace-clang.S
@@ -144,7 +144,7 @@ for_each_frame:	tst	frame, mask		@ Check for address exceptions
  */
 1003:		ldr	sv_lr, [sv_fp, #4]	@ get saved lr from next frame
 
-		ldr	r0, [sv_lr, #-4]	@ get call instruction
+1004:		ldr	r0, [sv_lr, #-4]	@ get call instruction
 		ldr	r3, .Lopcode+4
 		and	r2, r3, r0		@ is this a bl call
 		teq	r2, r3
@@ -164,7 +164,7 @@ finished_setup:
 /*
  * Print the function (sv_pc) and where it was called from (sv_lr).
  */
-1004:		mov	r0, sv_pc
+		mov	r0, sv_pc
 
 		mov	r1, sv_lr
 		mov	r2, frame
@@ -197,6 +197,14 @@ finished_setup:
 
 		cmp	sv_fp, frame		@ next frame must be
 		mov	frame, sv_fp		@ above the current frame
+#ifdef CONFIG_IRQSTACKS
+		@
+		@ Kernel stacks may be discontiguous in memory. If the next
+		@ frame is below the previous frame, accept it as long as it
+		@ lives in kernel memory.
+		@
+		cmpls	sv_fp, #PAGE_OFFSET
+#endif
 		bhi	for_each_frame
 
 1006:		adr	r0, .Lbad
@@ -210,7 +218,7 @@ ENDPROC(c_backtrace)
 		.long	1001b, 1006b
 		.long	1002b, 1006b
 		.long	1003b, 1006b
-		.long	1004b, 1006b
+		.long	1004b, finished_setup
 		.long   1005b, 1006b
 		.popsection
 
diff --git a/arch/arm/lib/backtrace.S b/arch/arm/lib/backtrace.S
index e8408f22d4dc..293a2716bd20 100644
--- a/arch/arm/lib/backtrace.S
+++ b/arch/arm/lib/backtrace.S
@@ -98,6 +98,14 @@ for_each_frame:	tst	frame, mask		@ Check for address exceptions
 
 		cmp	sv_fp, frame		@ next frame must be
 		mov	frame, sv_fp		@ above the current frame
+#ifdef CONFIG_IRQSTACKS
+		@
+		@ Kernel stacks may be discontiguous in memory. If the next
+		@ frame is below the previous frame, accept it as long as it
+		@ lives in kernel memory.
+		@
+		cmpls	sv_fp, #PAGE_OFFSET
+#endif
 		bhi	for_each_frame
 
 1006:		adr	r0, .Lbad
diff --git a/arch/arm/lib/call_with_stack.S b/arch/arm/lib/call_with_stack.S
index 28b0341ae786..5030d4e8d126 100644
--- a/arch/arm/lib/call_with_stack.S
+++ b/arch/arm/lib/call_with_stack.S
@@ -8,25 +8,44 @@
 
 #include <linux/linkage.h>
 #include <asm/assembler.h>
+#include <asm/unwind.h>
 
 /*
  * void call_with_stack(void (*fn)(void *), void *arg, void *sp)
  *
  * Change the stack to that pointed at by sp, then invoke fn(arg) with
  * the new stack.
+ *
+ * The sequence below follows the APCS frame convention for frame pointer
+ * unwinding, and implements the unwinder annotations needed by the EABI
+ * unwinder.
  */
-ENTRY(call_with_stack)
-	str	sp, [r2, #-4]!
-	str	lr, [r2, #-4]!
 
+ENTRY(call_with_stack)
+#if defined(CONFIG_UNWINDER_FRAME_POINTER) && defined(CONFIG_CC_IS_GCC)
+	mov	ip, sp
+	push	{fp, ip, lr, pc}
+	sub	fp, ip, #4
+#else
+UNWIND( .fnstart		)
+UNWIND( .save	{fpreg, lr}	)
+	push	{fpreg, lr}
+UNWIND( .setfp	fpreg, sp	)
+	mov	fpreg, sp
+#endif
 	mov	sp, r2
 	mov	r2, r0
 	mov	r0, r1
 
-	badr	lr, 1f
-	ret	r2
+	bl_r	r2
 
-1:	ldr	lr, [sp]
-	ldr	sp, [sp, #4]
-	ret	lr
+#if defined(CONFIG_UNWINDER_FRAME_POINTER) && defined(CONFIG_CC_IS_GCC)
+	ldmdb	fp, {fp, sp, pc}
+#else
+	mov	sp, fpreg
+	pop	{fpreg, pc}
+UNWIND( .fnend			)
+#endif
+	.globl call_with_stack_end
+call_with_stack_end:
 ENDPROC(call_with_stack)
diff --git a/arch/arm/lib/copy_from_user.S b/arch/arm/lib/copy_from_user.S
index 480a20766137..270de7debd0f 100644
--- a/arch/arm/lib/copy_from_user.S
+++ b/arch/arm/lib/copy_from_user.S
@@ -91,18 +91,15 @@
 	strb\cond \reg, [\ptr], #1
 	.endm
 
-	.macro enter reg1 reg2
+	.macro enter regs:vararg
 	mov	r3, #0
-	stmdb	sp!, {r0, r2, r3, \reg1, \reg2}
+UNWIND( .save	{r0, r2, r3, \regs}		)
+	stmdb	sp!, {r0, r2, r3, \regs}
 	.endm
 
-	.macro usave reg1 reg2
-	UNWIND(	.save {r0, r2, r3, \reg1, \reg2}	)
-	.endm
-
-	.macro exit reg1 reg2
+	.macro exit regs:vararg
 	add	sp, sp, #8
-	ldmfd	sp!, {r0, \reg1, \reg2}
+	ldmfd	sp!, {r0, \regs}
 	.endm
 
 	.text
diff --git a/arch/arm/lib/copy_template.S b/arch/arm/lib/copy_template.S
index 810a805d36dc..8fbafb074fe9 100644
--- a/arch/arm/lib/copy_template.S
+++ b/arch/arm/lib/copy_template.S
@@ -69,13 +69,10 @@
  *	than one 32bit instruction in Thumb-2)
  */
 
-
-	UNWIND(	.fnstart			)
-		enter	r4, lr
-	UNWIND(	.fnend				)
-
 	UNWIND(	.fnstart			)
-		usave	r4, lr			  @ in first stmdb block
+		enter	r4, UNWIND(fpreg,) lr
+	UNWIND(	.setfp	fpreg, sp		)
+	UNWIND(	mov	fpreg, sp		)
 
 		subs	r2, r2, #4
 		blt	8f
@@ -86,12 +83,7 @@
 		bne	10f
 
 1:		subs	r2, r2, #(28)
-		stmfd	sp!, {r5 - r8}
-	UNWIND(	.fnend				)
-
-	UNWIND(	.fnstart			)
-		usave	r4, lr
-	UNWIND(	.save	{r5 - r8}		) @ in second stmfd block
+		stmfd	sp!, {r5, r6, r8, r9}
 		blt	5f
 
 	CALGN(	ands	ip, r0, #31		)
@@ -110,9 +102,9 @@
 	PLD(	pld	[r1, #92]		)
 
 3:	PLD(	pld	[r1, #124]		)
-4:		ldr8w	r1, r3, r4, r5, r6, r7, r8, ip, lr, abort=20f
+4:		ldr8w	r1, r3, r4, r5, r6, r8, r9, ip, lr, abort=20f
 		subs	r2, r2, #32
-		str8w	r0, r3, r4, r5, r6, r7, r8, ip, lr, abort=20f
+		str8w	r0, r3, r4, r5, r6, r8, r9, ip, lr, abort=20f
 		bge	3b
 	PLD(	cmn	r2, #96			)
 	PLD(	bge	4b			)
@@ -132,8 +124,8 @@
 		ldr1w	r1, r4, abort=20f
 		ldr1w	r1, r5, abort=20f
 		ldr1w	r1, r6, abort=20f
-		ldr1w	r1, r7, abort=20f
 		ldr1w	r1, r8, abort=20f
+		ldr1w	r1, r9, abort=20f
 		ldr1w	r1, lr, abort=20f
 
 #if LDR1W_SHIFT < STR1W_SHIFT
@@ -150,17 +142,14 @@
 		str1w	r0, r4, abort=20f
 		str1w	r0, r5, abort=20f
 		str1w	r0, r6, abort=20f
-		str1w	r0, r7, abort=20f
 		str1w	r0, r8, abort=20f
+		str1w	r0, r9, abort=20f
 		str1w	r0, lr, abort=20f
 
 	CALGN(	bcs	2b			)
 
-7:		ldmfd	sp!, {r5 - r8}
-	UNWIND(	.fnend				) @ end of second stmfd block
+7:		ldmfd	sp!, {r5, r6, r8, r9}
 
-	UNWIND(	.fnstart			)
-		usave	r4, lr			  @ still in first stmdb block
 8:		movs	r2, r2, lsl #31
 		ldr1b	r1, r3, ne, abort=21f
 		ldr1b	r1, r4, cs, abort=21f
@@ -169,7 +158,7 @@
 		str1b	r0, r4, cs, abort=21f
 		str1b	r0, ip, cs, abort=21f
 
-		exit	r4, pc
+		exit	r4, UNWIND(fpreg,) pc
 
 9:		rsb	ip, ip, #4
 		cmp	ip, #2
@@ -189,13 +178,10 @@
 		ldr1w	r1, lr, abort=21f
 		beq	17f
 		bgt	18f
-	UNWIND(	.fnend				)
 
 
 		.macro	forward_copy_shift pull push
 
-	UNWIND(	.fnstart			)
-		usave	r4, lr			  @ still in first stmdb block
 		subs	r2, r2, #28
 		blt	14f
 
@@ -205,12 +191,8 @@
 	CALGN(	subcc	r2, r2, ip		)
 	CALGN(	bcc	15f			)
 
-11:		stmfd	sp!, {r5 - r9}
-	UNWIND(	.fnend				)
+11:		stmfd	sp!, {r5, r6, r8 - r10}
 
-	UNWIND(	.fnstart			)
-		usave	r4, lr
-	UNWIND(	.save	{r5 - r9}		) @ in new second stmfd block
 	PLD(	pld	[r1, #0]		)
 	PLD(	subs	r2, r2, #96		)
 	PLD(	pld	[r1, #28]		)
@@ -219,35 +201,32 @@
 	PLD(	pld	[r1, #92]		)
 
 12:	PLD(	pld	[r1, #124]		)
-13:		ldr4w	r1, r4, r5, r6, r7, abort=19f
+13:		ldr4w	r1, r4, r5, r6, r8, abort=19f
 		mov	r3, lr, lspull #\pull
 		subs	r2, r2, #32
-		ldr4w	r1, r8, r9, ip, lr, abort=19f
+		ldr4w	r1, r9, r10, ip, lr, abort=19f
 		orr	r3, r3, r4, lspush #\push
 		mov	r4, r4, lspull #\pull
 		orr	r4, r4, r5, lspush #\push
 		mov	r5, r5, lspull #\pull
 		orr	r5, r5, r6, lspush #\push
 		mov	r6, r6, lspull #\pull
-		orr	r6, r6, r7, lspush #\push
-		mov	r7, r7, lspull #\pull
-		orr	r7, r7, r8, lspush #\push
+		orr	r6, r6, r8, lspush #\push
 		mov	r8, r8, lspull #\pull
 		orr	r8, r8, r9, lspush #\push
 		mov	r9, r9, lspull #\pull
-		orr	r9, r9, ip, lspush #\push
+		orr	r9, r9, r10, lspush #\push
+		mov	r10, r10, lspull #\pull
+		orr	r10, r10, ip, lspush #\push
 		mov	ip, ip, lspull #\pull
 		orr	ip, ip, lr, lspush #\push
-		str8w	r0, r3, r4, r5, r6, r7, r8, r9, ip, abort=19f
+		str8w	r0, r3, r4, r5, r6, r8, r9, r10, ip, abort=19f
 		bge	12b
 	PLD(	cmn	r2, #96			)
 	PLD(	bge	13b			)
 
-		ldmfd	sp!, {r5 - r9}
-	UNWIND(	.fnend				) @ end of the second stmfd block
+		ldmfd	sp!, {r5, r6, r8 - r10}
 
-	UNWIND(	.fnstart			)
-		usave	r4, lr			  @ still in first stmdb block
 14:		ands	ip, r2, #28
 		beq	16f
 
@@ -262,7 +241,6 @@
 
 16:		sub	r1, r1, #(\push / 8)
 		b	8b
-	UNWIND(	.fnend				)
 
 		.endm
 
@@ -273,6 +251,7 @@
 
 18:		forward_copy_shift	pull=24	push=8
 
+	UNWIND(	.fnend				)
 
 /*
  * Abort preamble and completion macros.
@@ -282,13 +261,13 @@
  */
 
 	.macro	copy_abort_preamble
-19:	ldmfd	sp!, {r5 - r9}
+19:	ldmfd	sp!, {r5, r6, r8 - r10}
 	b	21f
-20:	ldmfd	sp!, {r5 - r8}
+20:	ldmfd	sp!, {r5, r6, r8, r9}
 21:
 	.endm
 
 	.macro	copy_abort_end
-	ldmfd	sp!, {r4, pc}
+	ldmfd	sp!, {r4, UNWIND(fpreg,) pc}
 	.endm
 
diff --git a/arch/arm/lib/copy_to_user.S b/arch/arm/lib/copy_to_user.S
index 842ea5ede485..fac49e57cc0b 100644
--- a/arch/arm/lib/copy_to_user.S
+++ b/arch/arm/lib/copy_to_user.S
@@ -90,18 +90,15 @@
 	strusr	\reg, \ptr, 1, \cond, abort=\abort
 	.endm
 
-	.macro enter reg1 reg2
+	.macro enter regs:vararg
 	mov	r3, #0
-	stmdb	sp!, {r0, r2, r3, \reg1, \reg2}
+UNWIND( .save	{r0, r2, r3, \regs}		)
+	stmdb	sp!, {r0, r2, r3, \regs}
 	.endm
 
-	.macro usave reg1 reg2
-	UNWIND(	.save {r0, r2, r3, \reg1, \reg2}	)
-	.endm
-
-	.macro exit reg1 reg2
+	.macro exit regs:vararg
 	add	sp, sp, #8
-	ldmfd	sp!, {r0, \reg1, \reg2}
+	ldmfd	sp!, {r0, \regs}
 	.endm
 
 	.text
diff --git a/arch/arm/lib/findbit.S b/arch/arm/lib/findbit.S
index b5e8b9ae4c7d..7fd3600db8ef 100644
--- a/arch/arm/lib/findbit.S
+++ b/arch/arm/lib/findbit.S
@@ -40,8 +40,8 @@ ENDPROC(_find_first_zero_bit_le)
  * Prototype: int find_next_zero_bit(void *addr, unsigned int maxbit, int offset)
  */
 ENTRY(_find_next_zero_bit_le)
-		teq	r1, #0
-		beq	3b
+		cmp	r2, r1
+		bhs	3b
 		ands	ip, r2, #7
 		beq	1b			@ If new byte, goto old routine
  ARM(		ldrb	r3, [r0, r2, lsr #3]	)
@@ -81,8 +81,8 @@ ENDPROC(_find_first_bit_le)
  * Prototype: int find_next_zero_bit(void *addr, unsigned int maxbit, int offset)
  */
 ENTRY(_find_next_bit_le)
-		teq	r1, #0
-		beq	3b
+		cmp	r2, r1
+		bhs	3b
 		ands	ip, r2, #7
 		beq	1b			@ If new byte, goto old routine
  ARM(		ldrb	r3, [r0, r2, lsr #3]	)
@@ -115,8 +115,8 @@ ENTRY(_find_first_zero_bit_be)
 ENDPROC(_find_first_zero_bit_be)
 
 ENTRY(_find_next_zero_bit_be)
-		teq	r1, #0
-		beq	3b
+		cmp	r2, r1
+		bhs	3b
 		ands	ip, r2, #7
 		beq	1b			@ If new byte, goto old routine
 		eor	r3, r2, #0x18		@ big endian byte ordering
@@ -149,8 +149,8 @@ ENTRY(_find_first_bit_be)
 ENDPROC(_find_first_bit_be)
 
 ENTRY(_find_next_bit_be)
-		teq	r1, #0
-		beq	3b
+		cmp	r2, r1
+		bhs	3b
 		ands	ip, r2, #7
 		beq	1b			@ If new byte, goto old routine
 		eor	r3, r2, #0x18		@ big endian byte ordering
diff --git a/arch/arm/lib/memcpy.S b/arch/arm/lib/memcpy.S
index e4caf48c089f..90f2b645aa0d 100644
--- a/arch/arm/lib/memcpy.S
+++ b/arch/arm/lib/memcpy.S
@@ -42,16 +42,13 @@
 	strb\cond \reg, [\ptr], #1
 	.endm
 
-	.macro enter reg1 reg2
-	stmdb sp!, {r0, \reg1, \reg2}
+	.macro enter regs:vararg
+UNWIND( .save	{r0, \regs}		)
+	stmdb sp!, {r0, \regs}
 	.endm
 
-	.macro usave reg1 reg2
-	UNWIND(	.save	{r0, \reg1, \reg2}	)
-	.endm
-
-	.macro exit reg1 reg2
-	ldmfd sp!, {r0, \reg1, \reg2}
+	.macro exit regs:vararg
+	ldmfd sp!, {r0, \regs}
 	.endm
 
 	.text
diff --git a/arch/arm/lib/memmove.S b/arch/arm/lib/memmove.S
index 6fecc12a1f51..6410554039fd 100644
--- a/arch/arm/lib/memmove.S
+++ b/arch/arm/lib/memmove.S
@@ -31,12 +31,13 @@ WEAK(memmove)
 		subs	ip, r0, r1
 		cmphi	r2, ip
 		bls	__memcpy
-
-		stmfd	sp!, {r0, r4, lr}
 	UNWIND(	.fnend				)
 
 	UNWIND(	.fnstart			)
-	UNWIND(	.save	{r0, r4, lr}		) @ in first stmfd block
+	UNWIND(	.save	{r0, r4, fpreg, lr}	)
+		stmfd	sp!, {r0, r4, UNWIND(fpreg,) lr}
+	UNWIND(	.setfp	fpreg, sp		)
+	UNWIND(	mov	fpreg, sp		)
 		add	r1, r1, r2
 		add	r0, r0, r2
 		subs	r2, r2, #4
@@ -48,12 +49,7 @@ WEAK(memmove)
 		bne	10f
 
 1:		subs	r2, r2, #(28)
-		stmfd	sp!, {r5 - r8}
-	UNWIND(	.fnend				)
-
-	UNWIND(	.fnstart			)
-	UNWIND(	.save	{r0, r4, lr}		)
-	UNWIND(	.save	{r5 - r8}		) @ in second stmfd block
+		stmfd	sp!, {r5, r6, r8, r9}
 		blt	5f
 
 	CALGN(	ands	ip, r0, #31		)
@@ -72,9 +68,9 @@ WEAK(memmove)
 	PLD(	pld	[r1, #-96]		)
 
 3:	PLD(	pld	[r1, #-128]		)
-4:		ldmdb	r1!, {r3, r4, r5, r6, r7, r8, ip, lr}
+4:		ldmdb	r1!, {r3, r4, r5, r6, r8, r9, ip, lr}
 		subs	r2, r2, #32
-		stmdb	r0!, {r3, r4, r5, r6, r7, r8, ip, lr}
+		stmdb	r0!, {r3, r4, r5, r6, r8, r9, ip, lr}
 		bge	3b
 	PLD(	cmn	r2, #96			)
 	PLD(	bge	4b			)
@@ -88,8 +84,8 @@ WEAK(memmove)
 		W(ldr)	r4, [r1, #-4]!
 		W(ldr)	r5, [r1, #-4]!
 		W(ldr)	r6, [r1, #-4]!
-		W(ldr)	r7, [r1, #-4]!
 		W(ldr)	r8, [r1, #-4]!
+		W(ldr)	r9, [r1, #-4]!
 		W(ldr)	lr, [r1, #-4]!
 
 		add	pc, pc, ip
@@ -99,17 +95,13 @@ WEAK(memmove)
 		W(str)	r4, [r0, #-4]!
 		W(str)	r5, [r0, #-4]!
 		W(str)	r6, [r0, #-4]!
-		W(str)	r7, [r0, #-4]!
 		W(str)	r8, [r0, #-4]!
+		W(str)	r9, [r0, #-4]!
 		W(str)	lr, [r0, #-4]!
 
 	CALGN(	bcs	2b			)
 
-7:		ldmfd	sp!, {r5 - r8}
-	UNWIND(	.fnend				) @ end of second stmfd block
-
-	UNWIND(	.fnstart			)
-	UNWIND(	.save	{r0, r4, lr}		) @ still in first stmfd block
+7:		ldmfd	sp!, {r5, r6, r8, r9}
 
 8:		movs	r2, r2, lsl #31
 		ldrbne	r3, [r1, #-1]!
@@ -118,7 +110,7 @@ WEAK(memmove)
 		strbne	r3, [r0, #-1]!
 		strbcs	r4, [r0, #-1]!
 		strbcs	ip, [r0, #-1]
-		ldmfd	sp!, {r0, r4, pc}
+		ldmfd	sp!, {r0, r4, UNWIND(fpreg,) pc}
 
 9:		cmp	ip, #2
 		ldrbgt	r3, [r1, #-1]!
@@ -137,13 +129,10 @@ WEAK(memmove)
 		ldr	r3, [r1, #0]
 		beq	17f
 		blt	18f
-	UNWIND(	.fnend				)
 
 
 		.macro	backward_copy_shift push pull
 
-	UNWIND(	.fnstart			)
-	UNWIND(	.save	{r0, r4, lr}		) @ still in first stmfd block
 		subs	r2, r2, #28
 		blt	14f
 
@@ -152,12 +141,7 @@ WEAK(memmove)
 	CALGN(	subcc	r2, r2, ip		)
 	CALGN(	bcc	15f			)
 
-11:		stmfd	sp!, {r5 - r9}
-	UNWIND(	.fnend				)
-
-	UNWIND(	.fnstart			)
-	UNWIND(	.save	{r0, r4, lr}		)
-	UNWIND(	.save	{r5 - r9}		) @ in new second stmfd block
+11:		stmfd	sp!, {r5, r6, r8 - r10}
 
 	PLD(	pld	[r1, #-4]		)
 	PLD(	subs	r2, r2, #96		)
@@ -167,35 +151,31 @@ WEAK(memmove)
 	PLD(	pld	[r1, #-96]		)
 
 12:	PLD(	pld	[r1, #-128]		)
-13:		ldmdb   r1!, {r7, r8, r9, ip}
+13:		ldmdb   r1!, {r8, r9, r10, ip}
 		mov     lr, r3, lspush #\push
 		subs    r2, r2, #32
 		ldmdb   r1!, {r3, r4, r5, r6}
 		orr     lr, lr, ip, lspull #\pull
 		mov     ip, ip, lspush #\push
-		orr     ip, ip, r9, lspull #\pull
+		orr     ip, ip, r10, lspull #\pull
+		mov     r10, r10, lspush #\push
+		orr     r10, r10, r9, lspull #\pull
 		mov     r9, r9, lspush #\push
 		orr     r9, r9, r8, lspull #\pull
 		mov     r8, r8, lspush #\push
-		orr     r8, r8, r7, lspull #\pull
-		mov     r7, r7, lspush #\push
-		orr     r7, r7, r6, lspull #\pull
+		orr     r8, r8, r6, lspull #\pull
 		mov     r6, r6, lspush #\push
 		orr     r6, r6, r5, lspull #\pull
 		mov     r5, r5, lspush #\push
 		orr     r5, r5, r4, lspull #\pull
 		mov     r4, r4, lspush #\push
 		orr     r4, r4, r3, lspull #\pull
-		stmdb   r0!, {r4 - r9, ip, lr}
+		stmdb   r0!, {r4 - r6, r8 - r10, ip, lr}
 		bge	12b
 	PLD(	cmn	r2, #96			)
 	PLD(	bge	13b			)
 
-		ldmfd	sp!, {r5 - r9}
-	UNWIND(	.fnend				) @ end of the second stmfd block
-
-	UNWIND(	.fnstart			)
-	UNWIND(	.save {r0, r4, lr}		) @ still in first stmfd block
+		ldmfd	sp!, {r5, r6, r8 - r10}
 
 14:		ands	ip, r2, #28
 		beq	16f
@@ -211,7 +191,6 @@ WEAK(memmove)
 
 16:		add	r1, r1, #(\pull / 8)
 		b	8b
-	UNWIND(	.fnend				)
 
 		.endm
 
@@ -222,5 +201,6 @@ WEAK(memmove)
 
 18:		backward_copy_shift	push=24	pull=8
 
+	UNWIND(	.fnend				)
 ENDPROC(memmove)
 ENDPROC(__memmove)
diff --git a/arch/arm/lib/memset.S b/arch/arm/lib/memset.S
index 9817cb258c1a..d71ab61430b2 100644
--- a/arch/arm/lib/memset.S
+++ b/arch/arm/lib/memset.S
@@ -28,16 +28,16 @@ UNWIND( .fnstart         )
 	mov	r3, r1
 7:	cmp	r2, #16
 	blt	4f
+UNWIND( .fnend              )
 
 #if ! CALGN(1)+0
 
 /*
  * We need 2 extra registers for this loop - use r8 and the LR
  */
-	stmfd	sp!, {r8, lr}
-UNWIND( .fnend              )
 UNWIND( .fnstart            )
 UNWIND( .save {r8, lr}      )
+	stmfd	sp!, {r8, lr}
 	mov	r8, r1
 	mov	lr, r3
 
@@ -66,10 +66,9 @@ UNWIND( .fnend              )
  * whole cache lines at once.
  */
 
-	stmfd	sp!, {r4-r8, lr}
-UNWIND( .fnend                 )
 UNWIND( .fnstart               )
 UNWIND( .save {r4-r8, lr}      )
+	stmfd	sp!, {r4-r8, lr}
 	mov	r4, r1
 	mov	r5, r3
 	mov	r6, r1
diff --git a/arch/arm/lib/uaccess_with_memcpy.c b/arch/arm/lib/uaccess_with_memcpy.c
index 106f83a5ea6d..14eecaaf295f 100644
--- a/arch/arm/lib/uaccess_with_memcpy.c
+++ b/arch/arm/lib/uaccess_with_memcpy.c
@@ -92,11 +92,6 @@ __copy_to_user_memcpy(void __user *to, const void *from, unsigned long n)
 	unsigned long ua_flags;
 	int atomic;
 
-	if (uaccess_kernel()) {
-		memcpy((void *)to, from, n);
-		return 0;
-	}
-
 	/* the mmap semaphore is taken only if not in an atomic context */
 	atomic = faulthandler_disabled();
 
@@ -165,11 +160,6 @@ __clear_user_memset(void __user *addr, unsigned long n)
 {
 	unsigned long ua_flags;
 
-	if (uaccess_kernel()) {
-		memset((void *)addr, 0, n);
-		return 0;
-	}
-
 	mmap_read_lock(current->mm);
 	while (n) {
 		pte_t *pte;
@@ -247,7 +237,7 @@ static int __init test_size_treshold(void)
 	if (!dst_page)
 		goto no_dst;
 	kernel_ptr = page_address(src_page);
-	user_ptr = vmap(&dst_page, 1, VM_IOREMAP, __pgprot(__P010));
+	user_ptr = vmap(&dst_page, 1, VM_IOREMAP, __pgprot(__PAGE_COPY));
 	if (!user_ptr)
 		goto no_vmap;
 
diff --git a/arch/arm/lib/xor-neon.c b/arch/arm/lib/xor-neon.c
index b99dd8e1c93f..522510baed49 100644
--- a/arch/arm/lib/xor-neon.c
+++ b/arch/arm/lib/xor-neon.c
@@ -17,17 +17,11 @@ MODULE_LICENSE("GPL");
 /*
  * Pull in the reference implementations while instructing GCC (through
  * -ftree-vectorize) to attempt to exploit implicit parallelism and emit
- * NEON instructions.
+ * NEON instructions. Clang does this by default at O2 so no pragma is
+ * needed.
  */
-#if __GNUC__ > 4 || (__GNUC__ == 4 && __GNUC_MINOR__ >= 6)
+#ifdef CONFIG_CC_IS_GCC
 #pragma GCC optimize "tree-vectorize"
-#else
-/*
- * While older versions of GCC do not generate incorrect code, they fail to
- * recognize the parallel nature of these functions, and emit plain ARM code,
- * which is known to be slower than the optimized ARM code in asm-arm/xor.h.
- */
-#warning This code requires at least version 4.6 of GCC
 #endif
 
 #pragma GCC diagnostic ignored "-Wunused-variable"
diff --git a/arch/arm/mach-airoha/Makefile b/arch/arm/mach-airoha/Makefile
new file mode 100644
index 000000000000..a5857d0d02eb
--- /dev/null
+++ b/arch/arm/mach-airoha/Makefile
@@ -0,0 +1,2 @@
+# SPDX-License-Identifier: GPL-2.0-only
+obj-y			+= airoha.o
diff --git a/arch/arm/mach-airoha/airoha.c b/arch/arm/mach-airoha/airoha.c
new file mode 100644
index 000000000000..ea23b5abb478
--- /dev/null
+++ b/arch/arm/mach-airoha/airoha.c
@@ -0,0 +1,16 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Device Tree support for Airoha SoCs
+ *
+ * Copyright (c) 2022 Felix Fietkau <nbd@nbd.name>
+ */
+#include <asm/mach/arch.h>
+
+static const char * const airoha_board_dt_compat[] = {
+	"airoha,en7523",
+	NULL,
+};
+
+DT_MACHINE_START(MEDIATEK_DT, "Airoha Cortex-A53 (Device Tree)")
+	.dt_compat	= airoha_board_dt_compat,
+MACHINE_END
diff --git a/arch/arm/mach-asm9260/Kconfig b/arch/arm/mach-asm9260/Kconfig
index a2e1d0aaf252..74e0f61c74c8 100644
--- a/arch/arm/mach-asm9260/Kconfig
+++ b/arch/arm/mach-asm9260/Kconfig
@@ -2,6 +2,7 @@
 config MACH_ASM9260
 	bool "Alphascale ASM9260"
 	depends on ARCH_MULTI_V5
+	depends on CPU_LITTLE_ENDIAN
 	select CPU_ARM926T
 	select ASM9260_TIMER
 	help
diff --git a/arch/arm/mach-aspeed/Kconfig b/arch/arm/mach-aspeed/Kconfig
index ea96d11b8502..080019aa6fcd 100644
--- a/arch/arm/mach-aspeed/Kconfig
+++ b/arch/arm/mach-aspeed/Kconfig
@@ -1,7 +1,7 @@
 # SPDX-License-Identifier: GPL-2.0-only
 menuconfig ARCH_ASPEED
 	bool "Aspeed BMC architectures"
-	depends on ARCH_MULTI_V5 || ARCH_MULTI_V6 || ARCH_MULTI_V7
+	depends on (CPU_LITTLE_ENDIAN && ARCH_MULTI_V5) || ARCH_MULTI_V6 || ARCH_MULTI_V7
 	select SRAM
 	select WATCHDOG
 	select ASPEED_WATCHDOG
@@ -19,9 +19,9 @@ config MACH_ASPEED_G4
 	select PINCTRL_ASPEED_G4
 	select FTTMR010_TIMER
 	help
-	 Say yes if you intend to run on an Aspeed ast2400 or similar
-	 fourth generation BMCs, such as those used by OpenPower Power8
-	 systems.
+	  Say yes if you intend to run on an Aspeed ast2400 or similar
+	  fourth generation BMCs, such as those used by OpenPower Power8
+	  systems.
 
 config MACH_ASPEED_G5
 	bool "Aspeed SoC 5th Generation"
@@ -29,8 +29,8 @@ config MACH_ASPEED_G5
 	select PINCTRL_ASPEED_G5
 	select FTTMR010_TIMER
 	help
-	 Say yes if you intend to run on an Aspeed ast2500 or similar
-	 fifth generation Aspeed BMCs.
+	  Say yes if you intend to run on an Aspeed ast2500 or similar
+	  fifth generation Aspeed BMCs.
 
 config MACH_ASPEED_G6
 	bool "Aspeed SoC 6th Generation"
@@ -40,7 +40,7 @@ config MACH_ASPEED_G6
 	select ARM_GIC
 	select HAVE_ARM_ARCH_TIMER
 	help
-	 Say yes if you intend to run on an Aspeed ast2600 or similar
-	 sixth generation Aspeed BMCs.
+	  Say yes if you intend to run on an Aspeed ast2600 or similar
+	  sixth generation Aspeed BMCs.
 
 endif
diff --git a/arch/arm/mach-at91/Kconfig b/arch/arm/mach-at91/Kconfig
index 02f6b108fd5d..3dd9e718661b 100644
--- a/arch/arm/mach-at91/Kconfig
+++ b/arch/arm/mach-at91/Kconfig
@@ -1,7 +1,8 @@
 # SPDX-License-Identifier: GPL-2.0-only
 menuconfig ARCH_AT91
 	bool "AT91/Microchip SoCs"
-	depends on ARCH_MULTI_V4T || ARCH_MULTI_V5 || ARCH_MULTI_V7 || ARM_SINGLE_ARMV7M
+	depends on (CPU_LITTLE_ENDIAN && (ARCH_MULTI_V4T || ARCH_MULTI_V5)) || \
+		ARCH_MULTI_V7 || ARM_SINGLE_ARMV7M
 	select ARM_CPU_SUSPEND if PM && ARCH_MULTI_V7
 	select COMMON_CLK_AT91
 	select GPIOLIB
@@ -63,6 +64,7 @@ config SOC_SAMA7G5
 	select HAVE_AT91_GENERATED_CLK
 	select HAVE_AT91_SAM9X60_PLL
 	select HAVE_AT91_UTMI
+	select PM_OPP
 	select SOC_SAMA7
 	help
 	  Select this if you are using one of Microchip's SAMA7G5 family SoC.
@@ -164,6 +166,15 @@ config ATMEL_CLOCKSOURCE_TCB
 	  to make a single 32-bit timer.
 	  It can also be used as a clock event device supporting oneshot mode.
 
+config MICROCHIP_CLOCKSOURCE_PIT64B
+	bool "64-bit Periodic Interval Timer (PIT64B) support"
+	default SOC_SAM9X60 || SOC_SAMA7
+	select MICROCHIP_PIT64B
+	help
+	  Select this to get a high resolution clockevent (SAM9X60) or
+	  clocksource and clockevent (SAMA7G5) based on Microchip 64-bit
+	  Periodic Interval Timer.
+
 config HAVE_AT91_UTMI
 	bool
 
@@ -210,6 +221,15 @@ config SOC_SAMA5
 config ATMEL_PM
 	bool
 
+config ATMEL_SECURE_PM
+	bool "Atmel Secure PM support"
+	depends on SOC_SAMA5D2 && ATMEL_PM
+	select ARM_PSCI
+	help
+	  When running under a TEE, the suspend mode must be requested to be set
+	  at TEE level. When enable, this option will use secure monitor calls
+	  to set the suspend level. PSCI is then used to enter suspend.
+
 config SOC_SAMA7
 	bool
 	select ARM_GIC
diff --git a/arch/arm/mach-at91/Makefile b/arch/arm/mach-at91/Makefile
index 522b680b6446..0dcc37180588 100644
--- a/arch/arm/mach-at91/Makefile
+++ b/arch/arm/mach-at91/Makefile
@@ -7,7 +7,7 @@
 obj-$(CONFIG_SOC_AT91RM9200)	+= at91rm9200.o
 obj-$(CONFIG_SOC_AT91SAM9)	+= at91sam9.o
 obj-$(CONFIG_SOC_SAM9X60)	+= sam9x60.o
-obj-$(CONFIG_SOC_SAMA5)		+= sama5.o
+obj-$(CONFIG_SOC_SAMA5)		+= sama5.o sam_secure.o
 obj-$(CONFIG_SOC_SAMA7)		+= sama7.o
 obj-$(CONFIG_SOC_SAMV7)		+= samv7.o
 
diff --git a/arch/arm/mach-at91/Makefile.boot b/arch/arm/mach-at91/Makefile.boot
deleted file mode 100644
index 5dde7328a7a9..000000000000
--- a/arch/arm/mach-at91/Makefile.boot
+++ /dev/null
@@ -1,4 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0-only
-# Empty file waiting for deletion once Makefile.boot isn't needed any more.
-# Patch waits for application at
-# https://www.arm.linux.org.uk/developer/patches/viewpatch.php?id=7889/1 .
diff --git a/arch/arm/mach-at91/pm.c b/arch/arm/mach-at91/pm.c
index 8711d6824c1f..60dc56d8acfb 100644
--- a/arch/arm/mach-at91/pm.c
+++ b/arch/arm/mach-at91/pm.c
@@ -15,11 +15,10 @@
 #include <linux/parser.h>
 #include <linux/suspend.h>
 
+#include <linux/clk.h>
 #include <linux/clk/at91_pmc.h>
 #include <linux/platform_data/atmel.h>
 
-#include <soc/at91/pm.h>
-
 #include <asm/cacheflush.h>
 #include <asm/fncpy.h>
 #include <asm/system_misc.h>
@@ -27,6 +26,7 @@
 
 #include "generic.h"
 #include "pm.h"
+#include "sam_secure.h"
 
 #define BACKUP_DDR_PHY_CALIBRATION	(9)
 
@@ -47,8 +47,8 @@ struct at91_pm_bu {
 	unsigned long ddr_phy_calibration[BACKUP_DDR_PHY_CALIBRATION];
 };
 
-/*
- * struct at91_pm_sfrbu_offsets: registers mapping for SFRBU
+/**
+ * struct at91_pm_sfrbu_regs - registers mapping for SFRBU
  * @pswbu: power switch BU control registers
  */
 struct at91_pm_sfrbu_regs {
@@ -61,13 +61,64 @@ struct at91_pm_sfrbu_regs {
 };
 
 /**
+ * enum at91_pm_eth_clk - Ethernet clock indexes
+ * @AT91_PM_ETH_PCLK: pclk index
+ * @AT91_PM_ETH_HCLK: hclk index
+ * @AT91_PM_ETH_MAX_CLK: max index
+ */
+enum at91_pm_eth_clk {
+	AT91_PM_ETH_PCLK,
+	AT91_PM_ETH_HCLK,
+	AT91_PM_ETH_MAX_CLK,
+};
+
+/**
+ * enum at91_pm_eth - Ethernet controller indexes
+ * @AT91_PM_G_ETH: gigabit Ethernet controller index
+ * @AT91_PM_E_ETH: megabit Ethernet controller index
+ * @AT91_PM_MAX_ETH: max index
+ */
+enum at91_pm_eth {
+	AT91_PM_G_ETH,
+	AT91_PM_E_ETH,
+	AT91_PM_MAX_ETH,
+};
+
+/**
+ * struct at91_pm_quirk_eth - AT91 PM Ethernet quirks
+ * @dev: Ethernet device
+ * @np: Ethernet device node
+ * @clks: Ethernet clocks
+ * @modes: power management mode that this quirk applies to
+ * @dns_modes: do not suspend modes: stop suspending if Ethernet is configured
+ *	       as wakeup source but buggy and no other wakeup source is
+ *	       available
+ */
+struct at91_pm_quirk_eth {
+	struct device *dev;
+	struct device_node *np;
+	struct clk_bulk_data clks[AT91_PM_ETH_MAX_CLK];
+	u32 modes;
+	u32 dns_modes;
+};
+
+/**
+ * struct at91_pm_quirks - AT91 PM quirks
+ * @eth: Ethernet quirks
+ */
+struct at91_pm_quirks {
+	struct at91_pm_quirk_eth eth[AT91_PM_MAX_ETH];
+};
+
+/**
  * struct at91_soc_pm - AT91 SoC power management data structure
  * @config_shdwc_ws: wakeup sources configuration function for SHDWC
  * @config_pmc_ws: wakeup srouces configuration function for PMC
  * @ws_ids: wakup sources of_device_id array
+ * @bu: backup unit mapped data (for backup mode)
+ * @quirks: PM quirks
  * @data: PM data to be used on last phase of suspend
  * @sfrbu_regs: SFRBU registers mapping
- * @bu: backup unit mapped data (for backup mode)
  * @memcs: memory chip select
  */
 struct at91_soc_pm {
@@ -75,19 +126,22 @@ struct at91_soc_pm {
 	int (*config_pmc_ws)(void __iomem *pmc, u32 mode, u32 polarity);
 	const struct of_device_id *ws_ids;
 	struct at91_pm_bu *bu;
+	struct at91_pm_quirks quirks;
 	struct at91_pm_data data;
 	struct at91_pm_sfrbu_regs sfrbu_regs;
 	void *memcs;
 };
 
 /**
- * enum at91_pm_iomaps:	IOs that needs to be mapped for different PM modes
+ * enum at91_pm_iomaps - IOs that needs to be mapped for different PM modes
  * @AT91_PM_IOMAP_SHDWC:	SHDWC controller
  * @AT91_PM_IOMAP_SFRBU:	SFRBU controller
+ * @AT91_PM_IOMAP_ETHC:		Ethernet controller
  */
 enum at91_pm_iomaps {
 	AT91_PM_IOMAP_SHDWC,
 	AT91_PM_IOMAP_SFRBU,
+	AT91_PM_IOMAP_ETHC,
 };
 
 #define AT91_PM_IOMAP(name)	BIT(AT91_PM_IOMAP_##name)
@@ -146,7 +200,7 @@ static const struct wakeup_source_info ws_info[] = {
 
 static const struct of_device_id sama5d2_ws_ids[] = {
 	{ .compatible = "atmel,sama5d2-gem",		.data = &ws_info[0] },
-	{ .compatible = "atmel,at91rm9200-rtc",		.data = &ws_info[1] },
+	{ .compatible = "atmel,sama5d2-rtc",		.data = &ws_info[1] },
 	{ .compatible = "atmel,sama5d3-udc",		.data = &ws_info[2] },
 	{ .compatible = "atmel,at91rm9200-ohci",	.data = &ws_info[2] },
 	{ .compatible = "usb-ohci",			.data = &ws_info[2] },
@@ -157,24 +211,24 @@ static const struct of_device_id sama5d2_ws_ids[] = {
 };
 
 static const struct of_device_id sam9x60_ws_ids[] = {
-	{ .compatible = "atmel,at91sam9x5-rtc",		.data = &ws_info[1] },
+	{ .compatible = "microchip,sam9x60-rtc",	.data = &ws_info[1] },
 	{ .compatible = "atmel,at91rm9200-ohci",	.data = &ws_info[2] },
 	{ .compatible = "usb-ohci",			.data = &ws_info[2] },
 	{ .compatible = "atmel,at91sam9g45-ehci",	.data = &ws_info[2] },
 	{ .compatible = "usb-ehci",			.data = &ws_info[2] },
-	{ .compatible = "atmel,at91sam9260-rtt",	.data = &ws_info[4] },
+	{ .compatible = "microchip,sam9x60-rtt",	.data = &ws_info[4] },
 	{ .compatible = "cdns,sam9x60-macb",		.data = &ws_info[5] },
 	{ /* sentinel */ }
 };
 
 static const struct of_device_id sama7g5_ws_ids[] = {
-	{ .compatible = "atmel,at91sam9x5-rtc",		.data = &ws_info[1] },
+	{ .compatible = "microchip,sama7g5-rtc",	.data = &ws_info[1] },
 	{ .compatible = "microchip,sama7g5-ohci",	.data = &ws_info[2] },
 	{ .compatible = "usb-ohci",			.data = &ws_info[2] },
 	{ .compatible = "atmel,at91sam9g45-ehci",	.data = &ws_info[2] },
 	{ .compatible = "usb-ehci",			.data = &ws_info[2] },
 	{ .compatible = "microchip,sama7g5-sdhci",	.data = &ws_info[3] },
-	{ .compatible = "atmel,at91sam9260-rtt",	.data = &ws_info[4] },
+	{ .compatible = "microchip,sama7g5-rtt",	.data = &ws_info[4] },
 	{ /* sentinel */ }
 };
 
@@ -263,6 +317,141 @@ static int at91_sam9x60_config_pmc_ws(void __iomem *pmc, u32 mode, u32 polarity)
 	return 0;
 }
 
+static bool at91_pm_eth_quirk_is_valid(struct at91_pm_quirk_eth *eth)
+{
+	struct platform_device *pdev;
+
+	/* Interface NA in DT. */
+	if (!eth->np)
+		return false;
+
+	/* No quirks for this interface and current suspend mode. */
+	if (!(eth->modes & BIT(soc_pm.data.mode)))
+		return false;
+
+	if (!eth->dev) {
+		/* Driver not probed. */
+		pdev = of_find_device_by_node(eth->np);
+		if (!pdev)
+			return false;
+		eth->dev = &pdev->dev;
+	}
+
+	/* No quirks if device isn't a wakeup source. */
+	if (!device_may_wakeup(eth->dev)) {
+		put_device(eth->dev);
+		return false;
+	}
+
+	/* put_device(eth->dev) is called at the end of suspend. */
+	return true;
+}
+
+static int at91_pm_config_quirks(bool suspend)
+{
+	struct at91_pm_quirk_eth *eth;
+	int i, j, ret, tmp;
+
+	/*
+	 * Ethernet IPs who's device_node pointers are stored into
+	 * soc_pm.quirks.eth[].np cannot handle WoL packets while in ULP0, ULP1
+	 * or both due to a hardware bug. If they receive WoL packets while in
+	 * ULP0 or ULP1 IPs could stop working or the whole system could stop
+	 * working. We cannot handle this scenario in the ethernet driver itself
+	 * as the driver is common to multiple vendors and also we only know
+	 * here, in this file, if we suspend to ULP0 or ULP1 mode. Thus handle
+	 * these scenarios here, as quirks.
+	 */
+	for (i = 0; i < AT91_PM_MAX_ETH; i++) {
+		eth = &soc_pm.quirks.eth[i];
+
+		if (!at91_pm_eth_quirk_is_valid(eth))
+			continue;
+
+		/*
+		 * For modes in dns_modes mask the system blocks if quirk is not
+		 * applied but if applied the interface doesn't act at WoL
+		 * events. Thus take care to avoid suspending if this interface
+		 * is the only configured wakeup source.
+		 */
+		if (suspend && eth->dns_modes & BIT(soc_pm.data.mode)) {
+			int ws_count = 0;
+#ifdef CONFIG_PM_SLEEP
+			struct wakeup_source *ws;
+
+			for_each_wakeup_source(ws) {
+				if (ws->dev == eth->dev)
+					continue;
+
+				ws_count++;
+				break;
+			}
+#endif
+
+			/*
+			 * Checking !ws is good for all platforms with issues
+			 * even when both G_ETH and E_ETH are available as dns_modes
+			 * is populated only on G_ETH interface.
+			 */
+			if (!ws_count) {
+				pr_err("AT91: PM: Ethernet cannot resume from WoL!");
+				ret = -EPERM;
+				put_device(eth->dev);
+				eth->dev = NULL;
+				/* No need to revert clock settings for this eth. */
+				i--;
+				goto clk_unconfigure;
+			}
+		}
+
+		if (suspend) {
+			clk_bulk_disable_unprepare(AT91_PM_ETH_MAX_CLK, eth->clks);
+		} else {
+			ret = clk_bulk_prepare_enable(AT91_PM_ETH_MAX_CLK,
+						      eth->clks);
+			if (ret)
+				goto clk_unconfigure;
+			/*
+			 * Release the reference to eth->dev taken in
+			 * at91_pm_eth_quirk_is_valid().
+			 */
+			put_device(eth->dev);
+			eth->dev = NULL;
+		}
+	}
+
+	return 0;
+
+clk_unconfigure:
+	/*
+	 * In case of resume we reach this point if clk_prepare_enable() failed.
+	 * we don't want to revert the previous clk_prepare_enable() for the
+	 * other IP.
+	 */
+	for (j = i; j >= 0; j--) {
+		eth = &soc_pm.quirks.eth[j];
+		if (suspend) {
+			if (!at91_pm_eth_quirk_is_valid(eth))
+				continue;
+
+			tmp = clk_bulk_prepare_enable(AT91_PM_ETH_MAX_CLK, eth->clks);
+			if (tmp) {
+				pr_err("AT91: PM: failed to enable %s clocks\n",
+				       j == AT91_PM_G_ETH ? "geth" : "eth");
+			}
+		} else {
+			/*
+			 * Release the reference to eth->dev taken in
+			 * at91_pm_eth_quirk_is_valid().
+			 */
+			put_device(eth->dev);
+			eth->dev = NULL;
+		}
+	}
+
+	return ret;
+}
+
 /*
  * Called after processes are frozen, but before we shutdown devices.
  */
@@ -350,10 +539,42 @@ extern u32 at91_pm_suspend_in_sram_sz;
 
 static int at91_suspend_finish(unsigned long val)
 {
+	unsigned char modified_gray_code[] = {
+		0x00, 0x01, 0x02, 0x03, 0x06, 0x07, 0x04, 0x05, 0x0c, 0x0d,
+		0x0e, 0x0f, 0x0a, 0x0b, 0x08, 0x09, 0x18, 0x19, 0x1a, 0x1b,
+		0x1e, 0x1f, 0x1c, 0x1d, 0x14, 0x15, 0x16, 0x17, 0x12, 0x13,
+		0x10, 0x11,
+	};
+	unsigned int tmp, index;
 	int i;
 
 	if (soc_pm.data.mode == AT91_PM_BACKUP && soc_pm.data.ramc_phy) {
 		/*
+		 * Bootloader will perform DDR recalibration and will try to
+		 * restore the ZQ0SR0 with the value saved here. But the
+		 * calibration is buggy and restoring some values from ZQ0SR0
+		 * is forbidden and risky thus we need to provide processed
+		 * values for these (modified gray code values).
+		 */
+		tmp = readl(soc_pm.data.ramc_phy + DDR3PHY_ZQ0SR0);
+
+		/* Store pull-down output impedance select. */
+		index = (tmp >> DDR3PHY_ZQ0SR0_PDO_OFF) & 0x1f;
+		soc_pm.bu->ddr_phy_calibration[0] = modified_gray_code[index];
+
+		/* Store pull-up output impedance select. */
+		index = (tmp >> DDR3PHY_ZQ0SR0_PUO_OFF) & 0x1f;
+		soc_pm.bu->ddr_phy_calibration[0] |= modified_gray_code[index];
+
+		/* Store pull-down on-die termination impedance select. */
+		index = (tmp >> DDR3PHY_ZQ0SR0_PDODT_OFF) & 0x1f;
+		soc_pm.bu->ddr_phy_calibration[0] |= modified_gray_code[index];
+
+		/* Store pull-up on-die termination impedance select. */
+		index = (tmp >> DDR3PHY_ZQ0SRO_PUODT_OFF) & 0x1f;
+		soc_pm.bu->ddr_phy_calibration[0] |= modified_gray_code[index];
+
+		/*
 		 * The 1st 8 words of memory might get corrupted in the process
 		 * of DDR PHY recalibration; it is saved here in securam and it
 		 * will be restored later, after recalibration, by bootloader
@@ -427,15 +648,11 @@ static void at91_pm_suspend(suspend_state_t state)
  */
 static int at91_pm_enter(suspend_state_t state)
 {
-#ifdef CONFIG_PINCTRL_AT91
-	/*
-	 * FIXME: this is needed to communicate between the pinctrl driver and
-	 * the PM implementation in the machine. Possibly part of the PM
-	 * implementation should be moved down into the pinctrl driver and get
-	 * called as part of the generic suspend/resume path.
-	 */
-	at91_pinctrl_gpio_suspend();
-#endif
+	int ret;
+
+	ret = at91_pm_config_quirks(true);
+	if (ret)
+		return ret;
 
 	switch (state) {
 	case PM_SUSPEND_MEM:
@@ -461,9 +678,7 @@ static int at91_pm_enter(suspend_state_t state)
 	}
 
 error:
-#ifdef CONFIG_PINCTRL_AT91
-	at91_pinctrl_gpio_resume();
-#endif
+	at91_pm_config_quirks(false);
 	return 0;
 }
 
@@ -605,6 +820,30 @@ static void at91sam9_sdram_standby(void)
 		at91_ramc_write(1, AT91_SDRAMC_LPR, saved_lpr1);
 }
 
+static void sama7g5_standby(void)
+{
+	int pwrtmg, ratio;
+
+	pwrtmg = readl(soc_pm.data.ramc[0] + UDDRC_PWRCTL);
+	ratio = readl(soc_pm.data.pmc + AT91_PMC_RATIO);
+
+	/*
+	 * Place RAM into self-refresh after a maximum idle clocks. The maximum
+	 * idle clocks is configured by bootloader in
+	 * UDDRC_PWRMGT.SELFREF_TO_X32.
+	 */
+	writel(pwrtmg | UDDRC_PWRCTL_SELFREF_EN,
+	       soc_pm.data.ramc[0] + UDDRC_PWRCTL);
+	/* Divide CPU clock by 16. */
+	writel(ratio & ~AT91_PMC_RATIO_RATIO, soc_pm.data.pmc + AT91_PMC_RATIO);
+
+	cpu_do_idle();
+
+	/* Restore previous configuration. */
+	writel(ratio, soc_pm.data.pmc + AT91_PMC_RATIO);
+	writel(pwrtmg, soc_pm.data.ramc[0] + UDDRC_PWRCTL);
+}
+
 struct ramc_info {
 	void (*idle)(void);
 	unsigned int memctrl;
@@ -615,6 +854,7 @@ static const struct ramc_info ramc_infos[] __initconst = {
 	{ .idle = at91sam9_sdram_standby, .memctrl = AT91_MEMCTRL_SDRAMC},
 	{ .idle = at91_ddr_standby, .memctrl = AT91_MEMCTRL_DDRSDR},
 	{ .idle = sama5d3_ddr_standby, .memctrl = AT91_MEMCTRL_DDRSDR},
+	{ .idle = sama7g5_standby, },
 };
 
 static const struct of_device_id ramc_ids[] __initconst = {
@@ -622,7 +862,7 @@ static const struct of_device_id ramc_ids[] __initconst = {
 	{ .compatible = "atmel,at91sam9260-sdramc", .data = &ramc_infos[1] },
 	{ .compatible = "atmel,at91sam9g45-ddramc", .data = &ramc_infos[2] },
 	{ .compatible = "atmel,sama5d3-ddramc", .data = &ramc_infos[3] },
-	{ .compatible = "microchip,sama7g5-uddrc", },
+	{ .compatible = "microchip,sama7g5-uddrc", .data = &ramc_infos[4], },
 	{ /*sentinel*/ }
 };
 
@@ -645,6 +885,7 @@ static __init int at91_dt_ramc(bool phy_mandatory)
 		if (!soc_pm.data.ramc[idx]) {
 			pr_err("unable to map ramc[%d] cpu registers\n", idx);
 			ret = -ENOMEM;
+			of_node_put(np);
 			goto unmap_ramc;
 		}
 
@@ -670,6 +911,7 @@ static __init int at91_dt_ramc(bool phy_mandatory)
 		if (!soc_pm.data.ramc_phy) {
 			pr_err("unable to map ramc phy cpu registers\n");
 			ret = -ENOMEM;
+			of_node_put(np);
 			goto unmap_ramc;
 		}
 	}
@@ -841,10 +1083,6 @@ static int __init at91_pm_backup_init(void)
 		of_scan_flat_dt(at91_pm_backup_scan_memcs, &located);
 		if (!located)
 			goto securam_fail;
-
-		/* DDR3PHY_ZQ0SR0 */
-		soc_pm.bu->ddr_phy_calibration[0] = readl(soc_pm.data.ramc_phy +
-							  0x188);
 	}
 
 	return 0;
@@ -854,6 +1092,35 @@ securam_fail:
 	return ret;
 }
 
+static void __init at91_pm_secure_init(void)
+{
+	int suspend_mode;
+	struct arm_smccc_res res;
+
+	suspend_mode = soc_pm.data.suspend_mode;
+
+	res = sam_smccc_call(SAMA5_SMC_SIP_SET_SUSPEND_MODE,
+			     suspend_mode, 0);
+	if (res.a0 == 0) {
+		pr_info("AT91: Secure PM: suspend mode set to %s\n",
+			pm_modes[suspend_mode].pattern);
+		return;
+	}
+
+	pr_warn("AT91: Secure PM: %s mode not supported !\n",
+		pm_modes[suspend_mode].pattern);
+
+	res = sam_smccc_call(SAMA5_SMC_SIP_GET_SUSPEND_MODE, 0, 0);
+	if (res.a0 == 0) {
+		pr_warn("AT91: Secure PM: failed to get default mode\n");
+		return;
+	}
+
+	pr_info("AT91: Secure PM: using default suspend mode %s\n",
+		pm_modes[suspend_mode].pattern);
+
+	soc_pm.data.suspend_mode = res.a1;
+}
 static const struct of_device_id atmel_shdwc_ids[] = {
 	{ .compatible = "atmel,sama5d2-shdwc" },
 	{ .compatible = "microchip,sam9x60-shdwc" },
@@ -861,10 +1128,99 @@ static const struct of_device_id atmel_shdwc_ids[] = {
 	{ /* sentinel. */ }
 };
 
+static const struct of_device_id gmac_ids[] __initconst = {
+	{ .compatible = "atmel,sama5d3-gem" },
+	{ .compatible = "atmel,sama5d2-gem" },
+	{ .compatible = "atmel,sama5d29-gem" },
+	{ .compatible = "microchip,sama7g5-gem" },
+	{ },
+};
+
+static const struct of_device_id emac_ids[] __initconst = {
+	{ .compatible = "atmel,sama5d3-macb" },
+	{ .compatible = "microchip,sama7g5-emac" },
+	{ },
+};
+
+/*
+ * Replaces _mode_to_replace with a supported mode that doesn't depend
+ * on controller pointed by _map_bitmask
+ * @_maps: u32 array containing AT91_PM_IOMAP() flags and indexed by AT91
+ * PM mode
+ * @_map_bitmask: AT91_PM_IOMAP() bitmask; if _mode_to_replace depends on
+ * controller represented by _map_bitmask, _mode_to_replace needs to be
+ * updated
+ * @_mode_to_replace: standby_mode or suspend_mode that need to be
+ * updated
+ * @_mode_to_check: standby_mode or suspend_mode; this is needed here
+ * to avoid having standby_mode and suspend_mode set with the same AT91
+ * PM mode
+ */
+#define AT91_PM_REPLACE_MODE(_maps, _map_bitmask, _mode_to_replace,	\
+			     _mode_to_check)				\
+	do {								\
+		if (((_maps)[(_mode_to_replace)]) & (_map_bitmask)) {	\
+			int _mode_to_use, _mode_complementary;		\
+			/* Use ULP0 if it doesn't need _map_bitmask. */	\
+			if (!((_maps)[AT91_PM_ULP0] & (_map_bitmask))) {\
+				_mode_to_use = AT91_PM_ULP0;		\
+				_mode_complementary = AT91_PM_STANDBY;	\
+			} else {					\
+				_mode_to_use = AT91_PM_STANDBY;		\
+				_mode_complementary = AT91_PM_STANDBY;	\
+			}						\
+									\
+			if ((_mode_to_check) != _mode_to_use)		\
+				(_mode_to_replace) = _mode_to_use;	\
+			else						\
+				(_mode_to_replace) = _mode_complementary;\
+		}							\
+	} while (0)
+
+/*
+ * Replaces standby and suspend modes with default supported modes:
+ * ULP0 and STANDBY.
+ * @_maps: u32 array indexed by AT91 PM mode containing AT91_PM_IOMAP()
+ * flags
+ * @_map: controller specific name; standby and suspend mode need to be
+ * replaced in order to not depend on this controller
+ */
+#define AT91_PM_REPLACE_MODES(_maps, _map)				\
+	do {								\
+		AT91_PM_REPLACE_MODE((_maps), BIT(AT91_PM_IOMAP_##_map),\
+				     (soc_pm.data.standby_mode),	\
+				     (soc_pm.data.suspend_mode));	\
+		AT91_PM_REPLACE_MODE((_maps), BIT(AT91_PM_IOMAP_##_map),\
+				     (soc_pm.data.suspend_mode),	\
+				     (soc_pm.data.standby_mode));	\
+	} while (0)
+
+static int __init at91_pm_get_eth_clks(struct device_node *np,
+				       struct clk_bulk_data *clks)
+{
+	clks[AT91_PM_ETH_PCLK].clk = of_clk_get_by_name(np, "pclk");
+	if (IS_ERR(clks[AT91_PM_ETH_PCLK].clk))
+		return PTR_ERR(clks[AT91_PM_ETH_PCLK].clk);
+
+	clks[AT91_PM_ETH_HCLK].clk = of_clk_get_by_name(np, "hclk");
+	if (IS_ERR(clks[AT91_PM_ETH_HCLK].clk))
+		return PTR_ERR(clks[AT91_PM_ETH_HCLK].clk);
+
+	return 0;
+}
+
+static int __init at91_pm_eth_clks_empty(struct clk_bulk_data *clks)
+{
+	return IS_ERR(clks[AT91_PM_ETH_PCLK].clk) ||
+	       IS_ERR(clks[AT91_PM_ETH_HCLK].clk);
+}
+
 static void __init at91_pm_modes_init(const u32 *maps, int len)
 {
+	struct at91_pm_quirk_eth *gmac = &soc_pm.quirks.eth[AT91_PM_G_ETH];
+	struct at91_pm_quirk_eth *emac = &soc_pm.quirks.eth[AT91_PM_E_ETH];
 	struct device_node *np;
-	int ret, mode;
+	int ret;
 
 	ret = at91_pm_backup_init();
 	if (ret) {
@@ -879,17 +1235,7 @@ static void __init at91_pm_modes_init(const u32 *maps, int len)
 		np = of_find_matching_node(NULL, atmel_shdwc_ids);
 		if (!np) {
 			pr_warn("%s: failed to find shdwc!\n", __func__);
-
-			/* Use ULP0 if it doesn't needs SHDWC.*/
-			if (!(maps[AT91_PM_ULP0] & AT91_PM_IOMAP(SHDWC)))
-				mode = AT91_PM_ULP0;
-			else
-				mode = AT91_PM_STANDBY;
-
-			if (maps[soc_pm.data.standby_mode] & AT91_PM_IOMAP(SHDWC))
-				soc_pm.data.standby_mode = mode;
-			if (maps[soc_pm.data.suspend_mode] & AT91_PM_IOMAP(SHDWC))
-				soc_pm.data.suspend_mode = mode;
+			AT91_PM_REPLACE_MODES(maps, SHDWC);
 		} else {
 			soc_pm.data.shdwc = of_iomap(np, 0);
 			of_node_put(np);
@@ -901,27 +1247,48 @@ static void __init at91_pm_modes_init(const u32 *maps, int len)
 		np = of_find_compatible_node(NULL, NULL, "atmel,sama5d2-sfrbu");
 		if (!np) {
 			pr_warn("%s: failed to find sfrbu!\n", __func__);
-
-			/*
-			 * Use ULP0 if it doesn't need SHDWC or if SHDWC
-			 * was already located.
-			 */
-			if (!(maps[AT91_PM_ULP0] & AT91_PM_IOMAP(SHDWC)) ||
-			    soc_pm.data.shdwc)
-				mode = AT91_PM_ULP0;
-			else
-				mode = AT91_PM_STANDBY;
-
-			if (maps[soc_pm.data.standby_mode] & AT91_PM_IOMAP(SFRBU))
-				soc_pm.data.standby_mode = mode;
-			if (maps[soc_pm.data.suspend_mode] & AT91_PM_IOMAP(SFRBU))
-				soc_pm.data.suspend_mode = mode;
+			AT91_PM_REPLACE_MODES(maps, SFRBU);
 		} else {
 			soc_pm.data.sfrbu = of_iomap(np, 0);
 			of_node_put(np);
 		}
 	}
 
+	if ((at91_is_pm_mode_active(AT91_PM_ULP1) ||
+	     at91_is_pm_mode_active(AT91_PM_ULP0) ||
+	     at91_is_pm_mode_active(AT91_PM_ULP0_FAST)) &&
+	    (maps[soc_pm.data.standby_mode] & AT91_PM_IOMAP(ETHC) ||
+	     maps[soc_pm.data.suspend_mode] & AT91_PM_IOMAP(ETHC))) {
+		np = of_find_matching_node(NULL, gmac_ids);
+		if (!np) {
+			np = of_find_matching_node(NULL, emac_ids);
+			if (np)
+				goto get_emac_clks;
+			AT91_PM_REPLACE_MODES(maps, ETHC);
+			goto unmap_unused_nodes;
+		} else {
+			gmac->np = np;
+			at91_pm_get_eth_clks(np, gmac->clks);
+		}
+
+		np = of_find_matching_node(NULL, emac_ids);
+		if (!np) {
+			if (at91_pm_eth_clks_empty(gmac->clks))
+				AT91_PM_REPLACE_MODES(maps, ETHC);
+		} else {
+get_emac_clks:
+			emac->np = np;
+			ret = at91_pm_get_eth_clks(np, emac->clks);
+			if (ret && at91_pm_eth_clks_empty(gmac->clks)) {
+				of_node_put(gmac->np);
+				of_node_put(emac->np);
+				gmac->np = NULL;
+				emac->np = NULL;
+			}
+		}
+	}
+
+unmap_unused_nodes:
 	/* Unmap all unnecessary. */
 	if (soc_pm.data.shdwc &&
 	    !(maps[soc_pm.data.standby_mode] & AT91_PM_IOMAP(SHDWC) ||
@@ -1157,17 +1524,30 @@ void __init sama5_pm_init(void)
 	static const int modes[] __initconst = {
 		AT91_PM_STANDBY, AT91_PM_ULP0, AT91_PM_ULP0_FAST,
 	};
+	static const u32 iomaps[] __initconst = {
+		[AT91_PM_ULP0]		= AT91_PM_IOMAP(ETHC),
+		[AT91_PM_ULP0_FAST]	= AT91_PM_IOMAP(ETHC),
+	};
 	int ret;
 
 	if (!IS_ENABLED(CONFIG_SOC_SAMA5))
 		return;
 
 	at91_pm_modes_validate(modes, ARRAY_SIZE(modes));
+	at91_pm_modes_init(iomaps, ARRAY_SIZE(iomaps));
 	ret = at91_dt_ramc(false);
 	if (ret)
 		return;
 
 	at91_pm_init(NULL);
+
+	/* Quirks applies to ULP0, ULP0 fast and ULP1 modes. */
+	soc_pm.quirks.eth[AT91_PM_G_ETH].modes = BIT(AT91_PM_ULP0) |
+						 BIT(AT91_PM_ULP0_FAST) |
+						 BIT(AT91_PM_ULP1);
+	/* Do not suspend in ULP0, ULP0 fast if GETH is the only wakeup source. */
+	soc_pm.quirks.eth[AT91_PM_G_ETH].dns_modes = BIT(AT91_PM_ULP0) |
+						     BIT(AT91_PM_ULP0_FAST);
 }
 
 void __init sama5d2_pm_init(void)
@@ -1177,7 +1557,10 @@ void __init sama5d2_pm_init(void)
 		AT91_PM_BACKUP,
 	};
 	static const u32 iomaps[] __initconst = {
-		[AT91_PM_ULP1]		= AT91_PM_IOMAP(SHDWC),
+		[AT91_PM_ULP0]		= AT91_PM_IOMAP(ETHC),
+		[AT91_PM_ULP0_FAST]	= AT91_PM_IOMAP(ETHC),
+		[AT91_PM_ULP1]		= AT91_PM_IOMAP(SHDWC) |
+					  AT91_PM_IOMAP(ETHC),
 		[AT91_PM_BACKUP]	= AT91_PM_IOMAP(SHDWC) |
 					  AT91_PM_IOMAP(SFRBU),
 	};
@@ -1186,6 +1569,12 @@ void __init sama5d2_pm_init(void)
 	if (!IS_ENABLED(CONFIG_SOC_SAMA5D2))
 		return;
 
+	if (IS_ENABLED(CONFIG_ATMEL_SECURE_PM)) {
+		pr_warn("AT91: Secure PM: ignoring standby mode\n");
+		at91_pm_secure_init();
+		return;
+	}
+
 	at91_pm_modes_validate(modes, ARRAY_SIZE(modes));
 	at91_pm_modes_init(iomaps, ARRAY_SIZE(iomaps));
 	ret = at91_dt_ramc(false);
@@ -1202,6 +1591,17 @@ void __init sama5d2_pm_init(void)
 	soc_pm.sfrbu_regs.pswbu.ctrl = BIT(0);
 	soc_pm.sfrbu_regs.pswbu.softsw = BIT(1);
 	soc_pm.sfrbu_regs.pswbu.state = BIT(3);
+
+	/* Quirk applies to ULP0, ULP0 fast and ULP1 modes. */
+	soc_pm.quirks.eth[AT91_PM_G_ETH].modes = BIT(AT91_PM_ULP0) |
+						 BIT(AT91_PM_ULP0_FAST) |
+						 BIT(AT91_PM_ULP1);
+	/*
+	 * Do not suspend in ULP0, ULP0 fast if GETH is the only wakeup
+	 * source.
+	 */
+	soc_pm.quirks.eth[AT91_PM_G_ETH].dns_modes = BIT(AT91_PM_ULP0) |
+						     BIT(AT91_PM_ULP0_FAST);
 }
 
 void __init sama7_pm_init(void)
@@ -1212,7 +1612,8 @@ void __init sama7_pm_init(void)
 	static const u32 iomaps[] __initconst = {
 		[AT91_PM_ULP0]		= AT91_PM_IOMAP(SFRBU),
 		[AT91_PM_ULP1]		= AT91_PM_IOMAP(SFRBU) |
-					  AT91_PM_IOMAP(SHDWC),
+					  AT91_PM_IOMAP(SHDWC) |
+					  AT91_PM_IOMAP(ETHC),
 		[AT91_PM_BACKUP]	= AT91_PM_IOMAP(SFRBU) |
 					  AT91_PM_IOMAP(SHDWC),
 	};
@@ -1237,6 +1638,10 @@ void __init sama7_pm_init(void)
 	soc_pm.sfrbu_regs.pswbu.ctrl = BIT(0);
 	soc_pm.sfrbu_regs.pswbu.softsw = BIT(1);
 	soc_pm.sfrbu_regs.pswbu.state = BIT(2);
+
+	/* Quirks applies to ULP1 for both Ethernet interfaces. */
+	soc_pm.quirks.eth[AT91_PM_E_ETH].modes = BIT(AT91_PM_ULP1);
+	soc_pm.quirks.eth[AT91_PM_G_ETH].modes = BIT(AT91_PM_ULP1);
 }
 
 static int __init at91_pm_modes_select(char *str)
diff --git a/arch/arm/mach-at91/pm_suspend.S b/arch/arm/mach-at91/pm_suspend.S
index fdb4f63ecde4..ffed4d949042 100644
--- a/arch/arm/mach-at91/pm_suspend.S
+++ b/arch/arm/mach-at91/pm_suspend.S
@@ -159,7 +159,7 @@ sr_ena_1:
 
 	/* Switch to self-refresh. */
 	ldr	tmp1, [r2, #UDDRC_PWRCTL]
-	orr	tmp1, tmp1, #UDDRC_PWRCTRL_SELFREF_SW
+	orr	tmp1, tmp1, #UDDRC_PWRCTL_SELFREF_SW
 	str	tmp1, [r2, #UDDRC_PWRCTL]
 
 sr_ena_2:
@@ -172,9 +172,15 @@ sr_ena_2:
 	/* Put DDR PHY's DLL in bypass mode for non-backup modes. */
 	cmp	r7, #AT91_PM_BACKUP
 	beq	sr_ena_3
-	ldr	tmp1, [r3, #DDR3PHY_PIR]
-	orr	tmp1, tmp1, #DDR3PHY_PIR_DLLBYP
-	str	tmp1, [r3, #DDR3PHY_PIR]
+
+	/* Disable DX DLLs. */
+	ldr	tmp1, [r3, #DDR3PHY_DX0DLLCR]
+	orr	tmp1, tmp1, #DDR3PHY_DXDLLCR_DLLDIS
+	str	tmp1, [r3, #DDR3PHY_DX0DLLCR]
+
+	ldr	tmp1, [r3, #DDR3PHY_DX1DLLCR]
+	orr	tmp1, tmp1, #DDR3PHY_DXDLLCR_DLLDIS
+	str	tmp1, [r3, #DDR3PHY_DX1DLLCR]
 
 sr_ena_3:
 	/* Power down DDR PHY data receivers. */
@@ -221,10 +227,14 @@ sr_ena_3:
 	bic	tmp1, tmp1, #DDR3PHY_DSGCR_ODTPDD_ODT0
 	str	tmp1, [r3, #DDR3PHY_DSGCR]
 
-	/* Take DDR PHY's DLL out of bypass mode. */
-	ldr	tmp1, [r3, #DDR3PHY_PIR]
-	bic	tmp1, tmp1, #DDR3PHY_PIR_DLLBYP
-	str	tmp1, [r3, #DDR3PHY_PIR]
+	/* Enable DX DLLs. */
+	ldr	tmp1, [r3, #DDR3PHY_DX0DLLCR]
+	bic	tmp1, tmp1, #DDR3PHY_DXDLLCR_DLLDIS
+	str	tmp1, [r3, #DDR3PHY_DX0DLLCR]
+
+	ldr	tmp1, [r3, #DDR3PHY_DX1DLLCR]
+	bic	tmp1, tmp1, #DDR3PHY_DXDLLCR_DLLDIS
+	str	tmp1, [r3, #DDR3PHY_DX1DLLCR]
 
 	/* Enable quasi-dynamic programming. */
 	mov	tmp1, #0
@@ -276,7 +286,7 @@ sr_dis_5:
 
 	/* Trigger self-refresh exit. */
 	ldr	tmp1, [r2, #UDDRC_PWRCTL]
-	bic	tmp1, tmp1, #UDDRC_PWRCTRL_SELFREF_SW
+	bic	tmp1, tmp1, #UDDRC_PWRCTL_SELFREF_SW
 	str	tmp1, [r2, #UDDRC_PWRCTL]
 
 sr_dis_6:
diff --git a/arch/arm/mach-at91/sam_secure.c b/arch/arm/mach-at91/sam_secure.c
new file mode 100644
index 000000000000..f7789cbe289f
--- /dev/null
+++ b/arch/arm/mach-at91/sam_secure.c
@@ -0,0 +1,52 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (C) 2022, Microchip
+ */
+
+#include <linux/arm-smccc.h>
+#include <linux/of.h>
+
+#include "sam_secure.h"
+
+static bool optee_available;
+
+#define SAM_SIP_SMC_STD_CALL_VAL(func_num) \
+	ARM_SMCCC_CALL_VAL(ARM_SMCCC_STD_CALL, ARM_SMCCC_SMC_32, \
+	ARM_SMCCC_OWNER_SIP, (func_num))
+
+struct arm_smccc_res sam_smccc_call(u32 fn, u32 arg0, u32 arg1)
+{
+	struct arm_smccc_res res = {.a0 = -1};
+
+	if (WARN_ON(!optee_available))
+		return res;
+
+	arm_smccc_smc(SAM_SIP_SMC_STD_CALL_VAL(fn), arg0, arg1, 0, 0, 0, 0, 0,
+		      &res);
+
+	return res;
+}
+
+bool sam_linux_is_optee_available(void)
+{
+	/* If optee has been detected, then we are running in normal world */
+	return optee_available;
+}
+
+void __init sam_secure_init(void)
+{
+	struct device_node *np;
+
+	/*
+	 * We only check that the OP-TEE node is present and available. The
+	 * OP-TEE kernel driver is not needed for the type of interaction made
+	 * with OP-TEE here so the driver's status is not checked.
+	 */
+	np = of_find_node_by_path("/firmware/optee");
+	if (np && of_device_is_available(np))
+		optee_available = true;
+	of_node_put(np);
+
+	if (optee_available)
+		pr_info("Running under OP-TEE firmware\n");
+}
diff --git a/arch/arm/mach-at91/sam_secure.h b/arch/arm/mach-at91/sam_secure.h
new file mode 100644
index 000000000000..1a0b5ebbfc39
--- /dev/null
+++ b/arch/arm/mach-at91/sam_secure.h
@@ -0,0 +1,19 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Copyright (C) 2022, Microchip
+ */
+
+#ifndef SAM_SECURE_H
+#define SAM_SECURE_H
+
+#include <linux/arm-smccc.h>
+
+/* Secure Monitor mode APIs */
+#define SAMA5_SMC_SIP_SET_SUSPEND_MODE	0x400
+#define SAMA5_SMC_SIP_GET_SUSPEND_MODE	0x401
+
+void __init sam_secure_init(void);
+struct arm_smccc_res sam_smccc_call(u32 fn, u32 arg0, u32 arg1);
+bool sam_linux_is_optee_available(void);
+
+#endif /* SAM_SECURE_H */
diff --git a/arch/arm/mach-at91/sama5.c b/arch/arm/mach-at91/sama5.c
index 89dab7cf01e8..67ed68fbe3a5 100644
--- a/arch/arm/mach-at91/sama5.c
+++ b/arch/arm/mach-at91/sama5.c
@@ -9,11 +9,26 @@
 #include <linux/of.h>
 #include <linux/of_platform.h>
 
+#include <asm/hardware/cache-l2x0.h>
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
+#include <asm/outercache.h>
 #include <asm/system_misc.h>
 
 #include "generic.h"
+#include "sam_secure.h"
+
+static void sama5_l2c310_write_sec(unsigned long val, unsigned reg)
+{
+	/* OP-TEE configures the L2 cache and does not allow modifying it yet */
+}
+
+static void __init sama5_secure_cache_init(void)
+{
+	sam_secure_init();
+	if (sam_linux_is_optee_available())
+		outer_cache.write_sec = sama5_l2c310_write_sec;
+}
 
 static void __init sama5_dt_device_init(void)
 {
@@ -58,6 +73,7 @@ static const char *const sama5d2_compat[] __initconst = {
 DT_MACHINE_START(sama5d2, "Atmel SAMA5")
 	/* Maintainer: Atmel */
 	.init_machine	= sama5d2_init,
+	.init_early	= sama5_secure_cache_init,
 	.dt_compat	= sama5d2_compat,
 	.l2c_aux_mask	= ~0UL,
 MACHINE_END
diff --git a/arch/arm/mach-axxia/platsmp.c b/arch/arm/mach-axxia/platsmp.c
index 512943eae30a..2e203626eda5 100644
--- a/arch/arm/mach-axxia/platsmp.c
+++ b/arch/arm/mach-axxia/platsmp.c
@@ -39,6 +39,7 @@ static int axxia_boot_secondary(unsigned int cpu, struct task_struct *idle)
 		return -ENOENT;
 
 	syscon = of_iomap(syscon_np, 0);
+	of_node_put(syscon_np);
 	if (!syscon)
 		return -ENOMEM;
 
diff --git a/arch/arm/mach-bcm/Kconfig b/arch/arm/mach-bcm/Kconfig
index bd3f82788ebc..8789d93a7c04 100644
--- a/arch/arm/mach-bcm/Kconfig
+++ b/arch/arm/mach-bcm/Kconfig
@@ -54,8 +54,6 @@ config ARCH_BCM_NSP
 	select ARM_ERRATA_775420
 	select ARM_ERRATA_764369 if SMP
 	select ARM_TIMER_SP804
-	select THERMAL
-	select THERMAL_OF
 	help
 	  Support for Broadcom Northstar Plus SoC.
 	  Broadcom Northstar Plus family of SoCs are used for switching control
@@ -182,24 +180,6 @@ config ARCH_BCM_53573
 	  The base chip is BCM53573 and there are some packaging modifications
 	  like BCM47189 and BCM47452.
 
-config ARCH_BCM_63XX
-	bool "Broadcom BCM63xx DSL SoC"
-	depends on ARCH_MULTI_V7
-	depends on MMU
-	select ARCH_HAS_RESET_CONTROLLER
-	select ARM_ERRATA_754322
-	select ARM_ERRATA_764369 if SMP
-	select ARM_GIC
-	select ARM_GLOBAL_TIMER
-	select CACHE_L2X0
-	select HAVE_ARM_ARCH_TIMER
-	select HAVE_ARM_TWD if SMP
-	select HAVE_ARM_SCU if SMP
-	help
-	  This enables support for systems based on Broadcom DSL SoCs.
-	  It currently supports the 'BCM63XX' ARM-based family, which includes
-	  the BCM63138 variant.
-
 config ARCH_BRCMSTB
 	bool "Broadcom BCM7XXX based boards"
 	depends on ARCH_MULTI_V7
@@ -219,4 +199,58 @@ config ARCH_BRCMSTB
 	  This enables support for Broadcom ARM-based set-top box chipsets,
 	  including the 7445 family of chips.
 
+menuconfig ARCH_BCMBCA
+	bool "Broadcom Broadband Carrier Access (BCA) origin SoC"
+	depends on ARCH_MULTI_V7
+	select ARM_AMBA
+	select ARM_GIC
+	select HAVE_ARM_ARCH_TIMER
+	help
+	  Say Y if you intend to run the kernel on a Broadcom Broadband ARM-based
+	  BCA chipset.
+
+	  This enables support for Broadcom BCA ARM-based broadband chipsets,
+	  including the DSL, PON and Wireless family of chips.
+
+comment "BCMBCA sub platforms"
+
+if ARCH_BCMBCA
+
+config ARCH_BCMBCA_CORTEXA7
+	bool "Cortex-A7 SoCs"
+	help
+	  Say Y if you intend to run the kernel on a Broadcom Broadband ARM A7
+	  based chipset.
+
+	  This enables support for Broadcom BCA ARM A7 broadband chipsets,
+	  including various DSL, PON and Wireless family of chips.
+
+config ARCH_BCMBCA_CORTEXA9
+	bool "Cortex-A9 SoCS"
+	select ARM_ERRATA_754322
+	select ARM_ERRATA_764369 if SMP
+	select ARCH_HAS_RESET_CONTROLLER
+	select ARM_GLOBAL_TIMER
+	select CACHE_L2X0
+	select HAVE_ARM_TWD if SMP
+	select HAVE_ARM_SCU if SMP
+	help
+	  Say Y if you intend to run the kernel on a Broadcom Broadband ARM A9
+	  based BCA chipset.
+
+	  This enables support for Broadcom BCA ARM A9 broadband chipset. Currently
+	  only DSL chip BCM63138.
+
+config ARCH_BCMBCA_BRAHMAB15
+	bool "Brahma-B15 SoCs"
+	select ARM_ERRATA_798181 if SMP
+	help
+	  Say Y if you intend to run the kernel on a Broadcom Broadband ARM B15
+	  based BCA chipset.
+
+	  This enables support for Broadcom BCA ARM B15 broadband chipset. Currently
+	  only DSL chip BCM63148.
+
+endif
+
 endif
diff --git a/arch/arm/mach-bcm/Makefile b/arch/arm/mach-bcm/Makefile
index 7baa8c9427d5..2e523f29ec3b 100644
--- a/arch/arm/mach-bcm/Makefile
+++ b/arch/arm/mach-bcm/Makefile
@@ -1,14 +1,7 @@
+# SPDX-License-Identifier: GPL-2.0-only
 #
 # Copyright (C) 2012-2015 Broadcom Corporation
 #
-# This program is free software; you can redistribute it and/or
-# modify it under the terms of the GNU General Public License as
-# published by the Free Software Foundation version 2.
-#
-# This program is distributed "as is" WITHOUT ANY WARRANTY of any
-# kind, whether express or implied; without even the implied warranty
-# of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
-# GNU General Public License for more details.
 
 # Cygnus
 obj-$(CONFIG_ARCH_BCM_CYGNUS) +=  bcm_cygnus.o
@@ -40,6 +33,7 @@ obj-$(CONFIG_ARCH_BCM_MOBILE_L2_CACHE) += kona_l2_cache.o
 
 # Support for secure monitor traps
 obj-$(CONFIG_ARCH_BCM_MOBILE_SMC) += bcm_kona_smc.o
+CFLAGS_REMOVE_bcm_kona_smc.o += $(CC_FLAGS_FTRACE)
 
 # BCM2835
 ifeq ($(CONFIG_ARCH_BCM2835),y)
@@ -56,14 +50,13 @@ ifeq ($(CONFIG_ARCH_BCM_5301X),y)
 obj-$(CONFIG_SMP)		+= platsmp.o
 endif
 
-# BCM63XXx
-ifeq ($(CONFIG_ARCH_BCM_63XX),y)
-obj-y				+= bcm63xx.o
-obj-$(CONFIG_SMP)		+= bcm63xx_smp.o bcm63xx_pmb.o
-endif
-
 ifeq ($(CONFIG_ARCH_BRCMSTB),y)
 CFLAGS_platsmp-brcmstb.o	+= -march=armv7-a
 obj-y				+= brcmstb.o
 obj-$(CONFIG_SMP)		+= platsmp-brcmstb.o
 endif
+
+# BCMBCA
+ifeq ($(CONFIG_ARCH_BCMBCA),y)
+obj-$(CONFIG_SMP)		+= bcm63xx_smp.o bcm63xx_pmb.o
+endif
diff --git a/arch/arm/mach-bcm/bcm63xx.c b/arch/arm/mach-bcm/bcm63xx.c
deleted file mode 100644
index c4c66ae51308..000000000000
--- a/arch/arm/mach-bcm/bcm63xx.c
+++ /dev/null
@@ -1,27 +0,0 @@
-/*
- * Copyright (C) 2014 Broadcom Corporation
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation version 2.
- *
- * This program is distributed "as is" WITHOUT ANY WARRANTY of any
- * kind, whether express or implied; without even the implied warranty
- * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- */
-
-#include <linux/of_platform.h>
-
-#include <asm/mach/arch.h>
-
-static const char * const bcm63xx_dt_compat[] = {
-	"brcm,bcm63138",
-	NULL
-};
-
-DT_MACHINE_START(BCM63XXX_DT, "BCM63xx DSL SoC")
-	.dt_compat	= bcm63xx_dt_compat,
-	.l2c_aux_val	= 0,
-	.l2c_aux_mask	= ~0,
-MACHINE_END
diff --git a/arch/arm/mach-bcm/bcm_cygnus.c b/arch/arm/mach-bcm/bcm_cygnus.c
index 7ae894c7849b..2469b66cc59e 100644
--- a/arch/arm/mach-bcm/bcm_cygnus.c
+++ b/arch/arm/mach-bcm/bcm_cygnus.c
@@ -1,15 +1,5 @@
-/*
- * Copyright (C) 2014 Broadcom Corporation
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation version 2.
- *
- * This program is distributed "as is" WITHOUT ANY WARRANTY of any
- * kind, whether express or implied; without even the implied warranty
- * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- */
+// SPDX-License-Identifier: GPL-2.0-only
+// Copyright (C) 2014 Broadcom Corporation
 
 #include <asm/mach/arch.h>
 
diff --git a/arch/arm/mach-bcm/bcm_hr2.c b/arch/arm/mach-bcm/bcm_hr2.c
index c104f28995d7..a19cc206ec76 100644
--- a/arch/arm/mach-bcm/bcm_hr2.c
+++ b/arch/arm/mach-bcm/bcm_hr2.c
@@ -1,15 +1,5 @@
-/*
- * Copyright (C) 2017 Broadcom
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation version 2.
- *
- * This program is distributed "as is" WITHOUT ANY WARRANTY of any
- * kind, whether express or implied; without even the implied warranty
- * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- */
+// SPDX-License-Identifier: GPL-2.0-only
+// Copyright (C) 2017 Broadcom
 
 #include <asm/mach/arch.h>
 
diff --git a/arch/arm/mach-bcm/bcm_kona_smc.c b/arch/arm/mach-bcm/bcm_kona_smc.c
index 43829e49ad93..185335843bbd 100644
--- a/arch/arm/mach-bcm/bcm_kona_smc.c
+++ b/arch/arm/mach-bcm/bcm_kona_smc.c
@@ -1,15 +1,5 @@
-/*
- * Copyright (C) 2013 Broadcom Corporation
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation version 2.
- *
- * This program is distributed "as is" WITHOUT ANY WARRANTY of any
- * kind, whether express or implied; without even the implied warranty
- * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- */
+// SPDX-License-Identifier: GPL-2.0-only
+// Copyright (C) 2013 Broadcom Corporation
 #include <linux/smp.h>
 #include <linux/io.h>
 #include <linux/ioport.h>
@@ -52,6 +42,7 @@ int __init bcm_kona_smc_init(void)
 		return -ENODEV;
 
 	prop_val = of_get_address(node, 0, &prop_size, NULL);
+	of_node_put(node);
 	if (!prop_val)
 		return -EINVAL;
 
diff --git a/arch/arm/mach-bcm/bcm_kona_smc.h b/arch/arm/mach-bcm/bcm_kona_smc.h
index 2e29ec67e414..17f3811fa543 100644
--- a/arch/arm/mach-bcm/bcm_kona_smc.h
+++ b/arch/arm/mach-bcm/bcm_kona_smc.h
@@ -1,15 +1,5 @@
-/*
- * Copyright (C) 2013 Broadcom Corporation
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation version 2.
- *
- * This program is distributed "as is" WITHOUT ANY WARRANTY of any
- * kind, whether express or implied; without even the implied warranty
- * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- */
+/* SPDX-License-Identifier: GPL-2.0-only */
+/* Copyright (C) 2013 Broadcom Corporation */
 
 #ifndef BCM_KONA_SMC_H
 #define BCM_KONA_SMC_H
diff --git a/arch/arm/mach-bcm/bcm_nsp.c b/arch/arm/mach-bcm/bcm_nsp.c
index a1101a3d318e..65ed9f8a518a 100644
--- a/arch/arm/mach-bcm/bcm_nsp.c
+++ b/arch/arm/mach-bcm/bcm_nsp.c
@@ -1,15 +1,5 @@
-/*
- * Copyright (C) 2015 Broadcom Corporation
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation version 2.
- *
- * This program is distributed "as is" WITHOUT ANY WARRANTY of any
- * kind, whether express or implied; without even the implied warranty
- * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- */
+// SPDX-License-Identifier: GPL-2.0-only
+// Copyright (C) 2015 Broadcom Corporation
 
 #include <asm/mach/arch.h>
 
diff --git a/arch/arm/mach-bcm/board_bcm21664.c b/arch/arm/mach-bcm/board_bcm21664.c
index c5bf01641172..9ce9ed092b09 100644
--- a/arch/arm/mach-bcm/board_bcm21664.c
+++ b/arch/arm/mach-bcm/board_bcm21664.c
@@ -1,15 +1,5 @@
-/*
- * Copyright (C) 2014 Broadcom Corporation
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation version 2.
- *
- * This program is distributed "as is" WITHOUT ANY WARRANTY of any
- * kind, whether express or implied; without even the implied warranty
- * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- */
+// SPDX-License-Identifier: GPL-2.0-only
+// Copyright (C) 2014 Broadcom Corporation
 
 #include <asm/mach/arch.h>
 
diff --git a/arch/arm/mach-bcm/board_bcm23550.c b/arch/arm/mach-bcm/board_bcm23550.c
index 0ac01debd077..dd6e9cb785e0 100644
--- a/arch/arm/mach-bcm/board_bcm23550.c
+++ b/arch/arm/mach-bcm/board_bcm23550.c
@@ -1,15 +1,5 @@
-/*
- * Copyright (C) 2016 Broadcom
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation version 2.
- *
- * This program is distributed "as is" WITHOUT ANY WARRANTY of any
- * kind, whether express or implied; without even the implied warranty
- * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- */
+// SPDX-License-Identifier: GPL-2.0-only
+// Copyright (C) 2016 Broadcom
 
 #include <linux/of_platform.h>
 
diff --git a/arch/arm/mach-bcm/board_bcm281xx.c b/arch/arm/mach-bcm/board_bcm281xx.c
index 1238ac801530..91f6d633ee8e 100644
--- a/arch/arm/mach-bcm/board_bcm281xx.c
+++ b/arch/arm/mach-bcm/board_bcm281xx.c
@@ -1,15 +1,5 @@
-/*
- * Copyright (C) 2012-2014 Broadcom Corporation
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation version 2.
- *
- * This program is distributed "as is" WITHOUT ANY WARRANTY of any
- * kind, whether express or implied; without even the implied warranty
- * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- */
+// SPDX-License-Identifier: GPL-2.0-only
+// Copyright (C) 2012-2014 Broadcom Corporation
 
 #include <linux/clocksource.h>
 #include <linux/of_address.h>
diff --git a/arch/arm/mach-bcm/brcmstb.c b/arch/arm/mach-bcm/brcmstb.c
index 5f127d5f1045..2e3385ced82a 100644
--- a/arch/arm/mach-bcm/brcmstb.c
+++ b/arch/arm/mach-bcm/brcmstb.c
@@ -1,15 +1,5 @@
-/*
- * Copyright (C) 2013-2014 Broadcom Corporation
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation version 2.
- *
- * This program is distributed "as is" WITHOUT ANY WARRANTY of any
- * kind, whether express or implied; without even the implied warranty
- * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- */
+// SPDX-License-Identifier: GPL-2.0-only
+// Copyright (C) 2013-2014 Broadcom Corporation
 
 #include <linux/init.h>
 #include <linux/irqchip.h>
diff --git a/arch/arm/mach-bcm/kona_l2_cache.c b/arch/arm/mach-bcm/kona_l2_cache.c
index 59ad86304092..457c66e1d7ae 100644
--- a/arch/arm/mach-bcm/kona_l2_cache.c
+++ b/arch/arm/mach-bcm/kona_l2_cache.c
@@ -1,15 +1,5 @@
-/*
- * Copyright (C) 2012-2014 Broadcom Corporation
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation version 2.
- *
- * This program is distributed "as is" WITHOUT ANY WARRANTY of any
- * kind, whether express or implied; without even the implied warranty
- * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- */
+// SPDX-License-Identifier: GPL-2.0-only
+// Copyright (C) 2012-2014 Broadcom Corporation
 
 
 #include <linux/init.h>
diff --git a/arch/arm/mach-bcm/kona_l2_cache.h b/arch/arm/mach-bcm/kona_l2_cache.h
index 46f84a95ab1c..77c5dc033910 100644
--- a/arch/arm/mach-bcm/kona_l2_cache.h
+++ b/arch/arm/mach-bcm/kona_l2_cache.h
@@ -1,15 +1,5 @@
-/*
- * Copyright (C) 2012-2014 Broadcom Corporation
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation version 2.
- *
- * This program is distributed "as is" WITHOUT ANY WARRANTY of any
- * kind, whether express or implied; without even the implied warranty
- * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- */
+/* SPDX-License-Identifier: GPL-2.0-only */
+/* Copyright (C) 2012-2014 Broadcom Corporation */
 
 #ifdef CONFIG_ARCH_BCM_MOBILE_L2_CACHE
 void	kona_l2_cache_init(void);
diff --git a/arch/arm/mach-bcm/platsmp-brcmstb.c b/arch/arm/mach-bcm/platsmp-brcmstb.c
index 4555f21e7077..8989299ebdd6 100644
--- a/arch/arm/mach-bcm/platsmp-brcmstb.c
+++ b/arch/arm/mach-bcm/platsmp-brcmstb.c
@@ -1,16 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Broadcom STB CPU SMP and hotplug support for ARM
  *
  * Copyright (C) 2013-2014 Broadcom Corporation
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation version 2.
- *
- * This program is distributed "as is" WITHOUT ANY WARRANTY of any
- * kind, whether express or implied; without even the implied warranty
- * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
  */
 
 #include <linux/delay.h>
@@ -59,7 +51,7 @@ static u32 hif_cont_reg;
 /*
  * We must quiesce a dying CPU before it can be killed by the boot CPU. Because
  * one or more cache may be disabled, we must flush to ensure coherency. We
- * cannot use traditionl completion structures or spinlocks as they rely on
+ * cannot use traditional completion structures or spinlocks as they rely on
  * coherency.
  */
 static DEFINE_PER_CPU_ALIGNED(int, per_cpu_sw_state);
diff --git a/arch/arm/mach-clps711x/Kconfig b/arch/arm/mach-clps711x/Kconfig
index 314de9477b84..fd32e576ecd0 100644
--- a/arch/arm/mach-clps711x/Kconfig
+++ b/arch/arm/mach-clps711x/Kconfig
@@ -2,6 +2,7 @@
 menuconfig ARCH_CLPS711X
 	bool "Cirrus Logic EP721x/EP731x-based"
 	depends on ARCH_MULTI_V4T
+	depends on CPU_LITTLE_ENDIAN
 	select CLPS711X_TIMER
 	select CPU_ARM720T
 	select GPIOLIB
diff --git a/arch/arm/mach-cns3xxx/Kconfig b/arch/arm/mach-cns3xxx/Kconfig
index 1ecf5466931e..1f85deff2486 100644
--- a/arch/arm/mach-cns3xxx/Kconfig
+++ b/arch/arm/mach-cns3xxx/Kconfig
@@ -2,6 +2,7 @@
 menuconfig ARCH_CNS3XXX
 	bool "Cavium Networks CNS3XXX family"
 	depends on ARCH_MULTI_V6
+	depends on ATAGS && UNUSED_BOARD_FILES
 	select ARM_GIC
 	help
 	  Support for Cavium Networks CNS3XXX platform.
diff --git a/arch/arm/mach-cns3xxx/core.c b/arch/arm/mach-cns3xxx/core.c
index e4f4b20b83a2..3fc4ec830e3a 100644
--- a/arch/arm/mach-cns3xxx/core.c
+++ b/arch/arm/mach-cns3xxx/core.c
@@ -372,6 +372,7 @@ static void __init cns3xxx_init(void)
 		/* De-Asscer SATA Reset */
 		cns3xxx_pwr_soft_rst(CNS3XXX_PWR_SOFTWARE_RST(SATA));
 	}
+	of_node_put(dn);
 
 	dn = of_find_compatible_node(NULL, NULL, "cavium,cns3420-sdhci");
 	if (of_device_is_available(dn)) {
@@ -385,6 +386,7 @@ static void __init cns3xxx_init(void)
 		cns3xxx_pwr_clk_en(CNS3XXX_PWR_CLK_EN(SDIO));
 		cns3xxx_pwr_soft_rst(CNS3XXX_PWR_SOFTWARE_RST(SDIO));
 	}
+	of_node_put(dn);
 
 	pm_power_off = cns3xxx_power_off;
 
diff --git a/arch/arm/mach-davinci/Kconfig b/arch/arm/mach-davinci/Kconfig
index 1d3aef84287d..c8cbd9a30791 100644
--- a/arch/arm/mach-davinci/Kconfig
+++ b/arch/arm/mach-davinci/Kconfig
@@ -3,6 +3,7 @@
 menuconfig ARCH_DAVINCI
 	bool "TI DaVinci"
 	depends on ARCH_MULTI_V5
+	depends on CPU_LITTLE_ENDIAN
 	select DAVINCI_TIMER
 	select ZONE_DMA
 	select PM_GENERIC_DOMAINS if PM
@@ -18,24 +19,16 @@ config ARCH_DAVINCI_DMx
 
 comment "DaVinci Core Type"
 
-config ARCH_DAVINCI_DM644x
-	bool "DaVinci 644x based system"
-	select DAVINCI_AINTC
-	select ARCH_DAVINCI_DMx
-
 config ARCH_DAVINCI_DM355
 	bool "DaVinci 355 based system"
-	select DAVINCI_AINTC
-	select ARCH_DAVINCI_DMx
-
-config ARCH_DAVINCI_DM646x
-	bool "DaVinci 646x based system"
+	depends on ATAGS && UNUSED_BOARD_FILES
 	select DAVINCI_AINTC
 	select ARCH_DAVINCI_DMx
 
 config ARCH_DAVINCI_DA830
 	bool "DA830/OMAP-L137/AM17x based system"
 	depends on !ARCH_DAVINCI_DMx || (AUTO_ZRELADDR && ARM_PATCH_PHYS_VIRT)
+	depends on ATAGS
 	select ARCH_DAVINCI_DA8XX
 	# needed on silicon revs 1.0, 1.1:
 	select CPU_DCACHE_WRITETHROUGH if !CPU_DCACHE_DISABLE
@@ -44,6 +37,7 @@ config ARCH_DAVINCI_DA830
 config ARCH_DAVINCI_DA850
 	bool "DA850/OMAP-L138/AM18x based system"
 	depends on !ARCH_DAVINCI_DMx || (AUTO_ZRELADDR && ARM_PATCH_PHYS_VIRT)
+	depends on ATAGS
 	select ARCH_DAVINCI_DA8XX
 	select DAVINCI_CP_INTC
 
@@ -52,6 +46,7 @@ config ARCH_DAVINCI_DA8XX
 
 config ARCH_DAVINCI_DM365
 	bool "DaVinci 365 based system"
+	depends on ATAGS && UNUSED_BOARD_FILES
 	select DAVINCI_AINTC
 	select ARCH_DAVINCI_DMx
 
@@ -66,28 +61,6 @@ config MACH_DA8XX_DT
 	  Say y here to include support for TI DaVinci DA850 based using
 	  Flattened Device Tree. More information at Documentation/devicetree
 
-config MACH_DAVINCI_EVM
-	bool "TI DM644x EVM"
-	default ARCH_DAVINCI_DM644x
-	depends on ARCH_DAVINCI_DM644x
-	help
-	  Configure this option to specify the whether the board used
-	  for development is a DM644x EVM
-
-config MACH_SFFSDR
-	bool "Lyrtech SFFSDR"
-	depends on ARCH_DAVINCI_DM644x
-	help
-	  Say Y here to select the Lyrtech Small Form Factor
-	  Software Defined Radio (SFFSDR) board.
-
-config MACH_NEUROS_OSD2
-	bool "Neuros OSD2 Open Television Set Top Box"
-	depends on ARCH_DAVINCI_DM644x
-	help
-	  Configure this option to specify the whether the board used
-	  for development is a Neuros OSD2 Open Set Top Box.
-
 config MACH_DAVINCI_DM355_EVM
 	bool "TI DM355 EVM"
 	default ARCH_DAVINCI_DM355
@@ -103,18 +76,6 @@ config MACH_DM355_LEOPARD
 	  Configure this option to specify the whether the board used
 	  for development is a DM355 Leopard board.
 
-config MACH_DAVINCI_DM6467_EVM
-	bool "TI DM6467 EVM"
-	default ARCH_DAVINCI_DM646x
-	depends on ARCH_DAVINCI_DM646x
-	select MACH_DAVINCI_DM6467TEVM
-	help
-	  Configure this option to specify the whether the board used
-	  for development is a DM6467 EVM
-
-config MACH_DAVINCI_DM6467TEVM
-	bool
-
 config MACH_DAVINCI_DM365_EVM
 	bool "TI DM365 EVM"
 	default ARCH_DAVINCI_DM365
@@ -126,6 +87,7 @@ config MACH_DAVINCI_DM365_EVM
 config MACH_DAVINCI_DA830_EVM
 	bool "TI DA830/OMAP-L137/AM17x Reference Platform"
 	default ARCH_DAVINCI_DA830
+	depends on ATAGS && UNUSED_BOARD_FILES
 	depends on ARCH_DAVINCI_DA830
 	select GPIO_PCF857X if I2C
 	help
@@ -155,6 +117,7 @@ endchoice
 
 config MACH_DAVINCI_DA850_EVM
 	bool "TI DA850/OMAP-L138/AM18x Reference Platform"
+	depends on ATAGS && UNUSED_BOARD_FILES
 	default ARCH_DAVINCI_DA850
 	depends on ARCH_DAVINCI_DA850
 	help
@@ -196,6 +159,7 @@ endchoice
 config MACH_MITYOMAPL138
 	bool "Critical Link MityDSP-L138/MityARM-1808 SoM"
 	depends on ARCH_DAVINCI_DA850
+	depends on ATAGS && UNUSED_BOARD_FILES
 	help
 	  Say Y here to select the Critical Link MityDSP-L138/MityARM-1808
 	  System on Module.  Information on this SoM may be found at
@@ -204,6 +168,7 @@ config MACH_MITYOMAPL138
 config MACH_OMAPL138_HAWKBOARD
 	bool "TI AM1808 / OMAPL-138 Hawkboard platform"
 	depends on ARCH_DAVINCI_DA850
+	depends on ATAGS && UNUSED_BOARD_FILES
 	help
 	  Say Y here to select the TI AM1808 / OMAPL-138 Hawkboard platform .
 
diff --git a/arch/arm/mach-davinci/Makefile b/arch/arm/mach-davinci/Makefile
index 58838a9de651..3f4894aa7528 100644
--- a/arch/arm/mach-davinci/Makefile
+++ b/arch/arm/mach-davinci/Makefile
@@ -3,30 +3,22 @@
 # Makefile for the linux kernel.
 #
 #
-
-ccflags-$(CONFIG_ARCH_MULTIPLATFORM) := -I$(srctree)/$(src)/include
-
+#
 # Common objects
 obj-y 					:= serial.o usb.o common.o sram.o
 
 obj-$(CONFIG_DAVINCI_MUX)		+= mux.o
 
 # Chip specific
-obj-$(CONFIG_ARCH_DAVINCI_DM644x)       += dm644x.o devices.o
 obj-$(CONFIG_ARCH_DAVINCI_DM355)        += dm355.o devices.o
-obj-$(CONFIG_ARCH_DAVINCI_DM646x)       += dm646x.o devices.o
 obj-$(CONFIG_ARCH_DAVINCI_DM365)	+= dm365.o devices.o
 obj-$(CONFIG_ARCH_DAVINCI_DA830)	+= da830.o devices-da8xx.o usb-da8xx.o
 obj-$(CONFIG_ARCH_DAVINCI_DA850)	+= da850.o devices-da8xx.o usb-da8xx.o
 
 # Board specific
 obj-$(CONFIG_MACH_DA8XX_DT)		+= da8xx-dt.o pdata-quirks.o
-obj-$(CONFIG_MACH_DAVINCI_EVM)  	+= board-dm644x-evm.o
-obj-$(CONFIG_MACH_SFFSDR)		+= board-sffsdr.o
-obj-$(CONFIG_MACH_NEUROS_OSD2)		+= board-neuros-osd2.o
 obj-$(CONFIG_MACH_DAVINCI_DM355_EVM)	+= board-dm355-evm.o
 obj-$(CONFIG_MACH_DM355_LEOPARD)	+= board-dm355-leopard.o
-obj-$(CONFIG_MACH_DAVINCI_DM6467_EVM)	+= board-dm646x-evm.o
 obj-$(CONFIG_MACH_DAVINCI_DM365_EVM)	+= board-dm365-evm.o
 obj-$(CONFIG_MACH_DAVINCI_DA830_EVM)	+= board-da830-evm.o
 obj-$(CONFIG_MACH_DAVINCI_DA850_EVM)	+= board-da850-evm.o
diff --git a/arch/arm/mach-davinci/Makefile.boot b/arch/arm/mach-davinci/Makefile.boot
deleted file mode 100644
index d36b251f325b..000000000000
--- a/arch/arm/mach-davinci/Makefile.boot
+++ /dev/null
@@ -1,8 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0
-zreladdr-$(CONFIG_ARCH_DAVINCI_DA8XX)		+= 0xc0008000
-params_phys-$(CONFIG_ARCH_DAVINCI_DA8XX)	:= 0xc0000100
-initrd_phys-$(CONFIG_ARCH_DAVINCI_DA8XX)	:= 0xc0800000
-
-zreladdr-$(CONFIG_ARCH_DAVINCI_DMx)		+= 0x80008000
-params_phys-$(CONFIG_ARCH_DAVINCI_DMx)		:= 0x80000100
-initrd_phys-$(CONFIG_ARCH_DAVINCI_DMx)		:= 0x80800000
diff --git a/arch/arm/mach-davinci/board-da830-evm.c b/arch/arm/mach-davinci/board-da830-evm.c
index 823c9cc98f18..6299e5c8f4ea 100644
--- a/arch/arm/mach-davinci/board-da830-evm.c
+++ b/arch/arm/mach-davinci/board-da830-evm.c
@@ -1,13 +1,11 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * TI DA830/OMAP L137 EVM board
  *
  * Author: Mark A. Greer <mgreer@mvista.com>
  * Derived from: arch/arm/mach-davinci/board-dm644x-evm.c
  *
- * 2007, 2009 (c) MontaVista Software, Inc. This file is licensed under
- * the terms of the GNU General Public License version 2. This program
- * is licensed "as is" without any warranty of any kind, whether express
- * or implied.
+ * 2007, 2009 (c) MontaVista Software, Inc.
  */
 #include <linux/kernel.h>
 #include <linux/init.h>
@@ -36,10 +34,9 @@
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
 
-#include <mach/common.h>
-#include <mach/mux.h>
-#include <mach/da8xx.h>
-
+#include "common.h"
+#include "mux.h"
+#include "da8xx.h"
 #include "irqs.h"
 
 #define DA830_EVM_PHY_ID		""
@@ -473,11 +470,10 @@ static int __init da830_evm_ui_expander_setup(struct i2c_client *client,
 	return 0;
 }
 
-static int da830_evm_ui_expander_teardown(struct i2c_client *client, int gpio,
+static void da830_evm_ui_expander_teardown(struct i2c_client *client, int gpio,
 		unsigned ngpio, void *context)
 {
 	gpio_free(gpio + 6);
-	return 0;
 }
 
 static struct pcf857x_platform_data __initdata da830_evm_ui_expander_info = {
diff --git a/arch/arm/mach-davinci/board-da850-evm.c b/arch/arm/mach-davinci/board-da850-evm.c
index 428012687a80..d752ee2b30ff 100644
--- a/arch/arm/mach-davinci/board-da850-evm.c
+++ b/arch/arm/mach-davinci/board-da850-evm.c
@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * TI DA850/OMAP-L138 EVM board
  *
@@ -6,10 +7,7 @@
  * Derived from: arch/arm/mach-davinci/board-da830-evm.c
  * Original Copyrights follow:
  *
- * 2007, 2009 (c) MontaVista Software, Inc. This file is licensed under
- * the terms of the GNU General Public License version 2. This program
- * is licensed "as is" without any warranty of any kind, whether express
- * or implied.
+ * 2007, 2009 (c) MontaVista Software, Inc.
  */
 #include <linux/console.h>
 #include <linux/delay.h>
@@ -43,10 +41,9 @@
 #include <linux/spi/spi.h>
 #include <linux/spi/flash.h>
 
-#include <mach/common.h>
-#include <mach/da8xx.h>
-#include <mach/mux.h>
-
+#include "common.h"
+#include "da8xx.h"
+#include "mux.h"
 #include "irqs.h"
 #include "sram.h"
 
@@ -519,8 +516,8 @@ exp_setup_sela_fail:
 	return ret;
 }
 
-static int da850_evm_ui_expander_teardown(struct i2c_client *client,
-					unsigned gpio, unsigned ngpio, void *c)
+static void da850_evm_ui_expander_teardown(struct i2c_client *client,
+					   unsigned gpio, unsigned ngpio, void *c)
 {
 	platform_device_unregister(&da850_evm_ui_keys_device);
 
@@ -532,8 +529,6 @@ static int da850_evm_ui_expander_teardown(struct i2c_client *client,
 	gpio_free(gpio + DA850_EVM_UI_EXP_SEL_C);
 	gpio_free(gpio + DA850_EVM_UI_EXP_SEL_B);
 	gpio_free(gpio + DA850_EVM_UI_EXP_SEL_A);
-
-	return 0;
 }
 
 /* assign the baseboard expander's GPIOs after the UI board's */
@@ -700,13 +695,11 @@ io_exp_setup_sw_fail:
 	return ret;
 }
 
-static int da850_evm_bb_expander_teardown(struct i2c_client *client,
-					unsigned gpio, unsigned ngpio, void *c)
+static void da850_evm_bb_expander_teardown(struct i2c_client *client,
+					   unsigned gpio, unsigned ngpio, void *c)
 {
 	platform_device_unregister(&da850_evm_bb_leds_device);
 	platform_device_unregister(&da850_evm_bb_keys_device);
-
-	return 0;
 }
 
 static struct pca953x_platform_data da850_evm_ui_expander_info = {
@@ -1101,11 +1094,13 @@ static int __init da850_evm_config_emac(void)
 	int ret;
 	u32 val;
 	struct davinci_soc_info *soc_info = &davinci_soc_info;
-	u8 rmii_en = soc_info->emac_pdata->rmii_en;
+	u8 rmii_en;
 
 	if (!machine_is_davinci_da850_evm())
 		return 0;
 
+	rmii_en = soc_info->emac_pdata->rmii_en;
+
 	cfg_chip3_base = DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP3_REG);
 
 	val = __raw_readl(cfg_chip3_base);
diff --git a/arch/arm/mach-davinci/board-dm355-evm.c b/arch/arm/mach-davinci/board-dm355-evm.c
index 3c5a9e3c128a..b48ab1c3e48b 100644
--- a/arch/arm/mach-davinci/board-dm355-evm.c
+++ b/arch/arm/mach-davinci/board-dm355-evm.c
@@ -1,12 +1,10 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * TI DaVinci EVM board support
  *
  * Author: Kevin Hilman, Deep Root Systems, LLC
  *
- * 2007 (c) MontaVista Software, Inc. This file is licensed under
- * the terms of the GNU General Public License version 2. This program
- * is licensed "as is" without any warranty of any kind, whether express
- * or implied.
+ * 2007 (c) MontaVista Software, Inc.
  */
 #include <linux/kernel.h>
 #include <linux/init.h>
@@ -33,9 +31,8 @@
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
 
-#include <mach/serial.h>
-#include <mach/common.h>
-
+#include "serial.h"
+#include "common.h"
 #include "davinci.h"
 
 /* NOTE:  this is geared for the standard config, with a socketed
diff --git a/arch/arm/mach-davinci/board-dm355-leopard.c b/arch/arm/mach-davinci/board-dm355-leopard.c
index e475b2113e70..32b9d607d025 100644
--- a/arch/arm/mach-davinci/board-dm355-leopard.c
+++ b/arch/arm/mach-davinci/board-dm355-leopard.c
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * DM355 leopard board support
  *
  * Based on board-dm355-evm.c
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 #include <linux/kernel.h>
 #include <linux/init.h>
@@ -27,9 +24,8 @@
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
 
-#include <mach/common.h>
-#include <mach/serial.h>
-
+#include "common.h"
+#include "serial.h"
 #include "davinci.h"
 
 /* NOTE:  this is geared for the standard config, with a socketed
diff --git a/arch/arm/mach-davinci/board-dm365-evm.c b/arch/arm/mach-davinci/board-dm365-evm.c
index b3bef74c982a..d8c6c360818b 100644
--- a/arch/arm/mach-davinci/board-dm365-evm.c
+++ b/arch/arm/mach-davinci/board-dm365-evm.c
@@ -1,16 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * TI DaVinci DM365 EVM board support
  *
  * Copyright (C) 2009 Texas Instruments Incorporated
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation version 2.
- *
- * This program is distributed "as is" WITHOUT ANY WARRANTY of any
- * kind, whether express or implied; without even the implied warranty
- * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
  */
 #include <linux/kernel.h>
 #include <linux/init.h>
@@ -36,10 +28,7 @@
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
 
-#include <mach/mux.h>
-#include <mach/common.h>
 #include <linux/platform_data/i2c-davinci.h>
-#include <mach/serial.h>
 #include <linux/platform_data/mmc-davinci.h>
 #include <linux/platform_data/mtd-davinci.h>
 #include <linux/platform_data/keyscan-davinci.h>
@@ -47,6 +36,9 @@
 #include <media/i2c/ths7303.h>
 #include <media/i2c/tvp514x.h>
 
+#include "mux.h"
+#include "common.h"
+#include "serial.h"
 #include "davinci.h"
 
 static inline int have_imager(void)
@@ -861,4 +853,3 @@ MACHINE_START(DAVINCI_DM365_EVM, "DaVinci DM365 EVM")
 	.init_late	= davinci_init_late,
 	.dma_zone_size	= SZ_128M,
 MACHINE_END
-
diff --git a/arch/arm/mach-davinci/board-dm644x-evm.c b/arch/arm/mach-davinci/board-dm644x-evm.c
deleted file mode 100644
index cce3a621eb20..000000000000
--- a/arch/arm/mach-davinci/board-dm644x-evm.c
+++ /dev/null
@@ -1,932 +0,0 @@
-/*
- * TI DaVinci EVM board support
- *
- * Author: Kevin Hilman, MontaVista Software, Inc. <source@mvista.com>
- *
- * 2007 (c) MontaVista Software, Inc. This file is licensed under
- * the terms of the GNU General Public License version 2. This program
- * is licensed "as is" without any warranty of any kind, whether express
- * or implied.
- */
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/dma-mapping.h>
-#include <linux/platform_device.h>
-#include <linux/gpio.h>
-#include <linux/gpio/machine.h>
-#include <linux/i2c.h>
-#include <linux/platform_data/pcf857x.h>
-#include <linux/platform_data/gpio-davinci.h>
-#include <linux/property.h>
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/rawnand.h>
-#include <linux/mtd/partitions.h>
-#include <linux/mtd/physmap.h>
-#include <linux/nvmem-provider.h>
-#include <linux/phy.h>
-#include <linux/clk.h>
-#include <linux/videodev2.h>
-#include <linux/v4l2-dv-timings.h>
-#include <linux/export.h>
-#include <linux/leds.h>
-#include <linux/regulator/fixed.h>
-#include <linux/regulator/machine.h>
-
-#include <media/i2c/tvp514x.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-
-#include <mach/common.h>
-#include <mach/mux.h>
-#include <mach/serial.h>
-
-#include <linux/platform_data/i2c-davinci.h>
-#include <linux/platform_data/mtd-davinci.h>
-#include <linux/platform_data/mmc-davinci.h>
-#include <linux/platform_data/usb-davinci.h>
-#include <linux/platform_data/mtd-davinci-aemif.h>
-#include <linux/platform_data/ti-aemif.h>
-
-#include "davinci.h"
-#include "irqs.h"
-
-#define DM644X_EVM_PHY_ID		"davinci_mdio-0:01"
-#define LXT971_PHY_ID	(0x001378e2)
-#define LXT971_PHY_MASK	(0xfffffff0)
-
-static struct mtd_partition davinci_evm_norflash_partitions[] = {
-	/* bootloader (UBL, U-Boot, etc) in first 5 sectors */
-	{
-		.name		= "bootloader",
-		.offset		= 0,
-		.size		= 5 * SZ_64K,
-		.mask_flags	= MTD_WRITEABLE, /* force read-only */
-	},
-	/* bootloader params in the next 1 sectors */
-	{
-		.name		= "params",
-		.offset		= MTDPART_OFS_APPEND,
-		.size		= SZ_64K,
-		.mask_flags	= 0,
-	},
-	/* kernel */
-	{
-		.name		= "kernel",
-		.offset		= MTDPART_OFS_APPEND,
-		.size		= SZ_2M,
-		.mask_flags	= 0
-	},
-	/* file system */
-	{
-		.name		= "filesystem",
-		.offset		= MTDPART_OFS_APPEND,
-		.size		= MTDPART_SIZ_FULL,
-		.mask_flags	= 0
-	}
-};
-
-static struct physmap_flash_data davinci_evm_norflash_data = {
-	.width		= 2,
-	.parts		= davinci_evm_norflash_partitions,
-	.nr_parts	= ARRAY_SIZE(davinci_evm_norflash_partitions),
-};
-
-/* NOTE: CFI probe will correctly detect flash part as 32M, but EMIF
- * limits addresses to 16M, so using addresses past 16M will wrap */
-static struct resource davinci_evm_norflash_resource = {
-	.start		= DM644X_ASYNC_EMIF_DATA_CE0_BASE,
-	.end		= DM644X_ASYNC_EMIF_DATA_CE0_BASE + SZ_16M - 1,
-	.flags		= IORESOURCE_MEM,
-};
-
-static struct platform_device davinci_evm_norflash_device = {
-	.name		= "physmap-flash",
-	.id		= 0,
-	.dev		= {
-		.platform_data	= &davinci_evm_norflash_data,
-	},
-	.num_resources	= 1,
-	.resource	= &davinci_evm_norflash_resource,
-};
-
-/* DM644x EVM includes a 64 MByte small-page NAND flash (16K blocks).
- * It may used instead of the (default) NOR chip to boot, using TI's
- * tools to install the secondary boot loader (UBL) and U-Boot.
- */
-static struct mtd_partition davinci_evm_nandflash_partition[] = {
-	/* Bootloader layout depends on whose u-boot is installed, but we
-	 * can hide all the details.
-	 *  - block 0 for u-boot environment ... in mainline u-boot
-	 *  - block 1 for UBL (plus up to four backup copies in blocks 2..5)
-	 *  - blocks 6...? for u-boot
-	 *  - blocks 16..23 for u-boot environment ... in TI's u-boot
-	 */
-	{
-		.name		= "bootloader",
-		.offset		= 0,
-		.size		= SZ_256K + SZ_128K,
-		.mask_flags	= MTD_WRITEABLE,	/* force read-only */
-	},
-	/* Kernel */
-	{
-		.name		= "kernel",
-		.offset		= MTDPART_OFS_APPEND,
-		.size		= SZ_4M,
-		.mask_flags	= 0,
-	},
-	/* File system (older GIT kernels started this on the 5MB mark) */
-	{
-		.name		= "filesystem",
-		.offset		= MTDPART_OFS_APPEND,
-		.size		= MTDPART_SIZ_FULL,
-		.mask_flags	= 0,
-	}
-	/* A few blocks at end hold a flash BBT ... created by TI's CCS
-	 * using flashwriter_nand.out, but ignored by TI's versions of
-	 * Linux and u-boot.  We boot faster by using them.
-	 */
-};
-
-static struct davinci_aemif_timing davinci_evm_nandflash_timing = {
-	.wsetup		= 20,
-	.wstrobe	= 40,
-	.whold		= 20,
-	.rsetup		= 10,
-	.rstrobe	= 40,
-	.rhold		= 10,
-	.ta		= 40,
-};
-
-static struct davinci_nand_pdata davinci_evm_nandflash_data = {
-	.core_chipsel	= 0,
-	.parts		= davinci_evm_nandflash_partition,
-	.nr_parts	= ARRAY_SIZE(davinci_evm_nandflash_partition),
-	.engine_type	= NAND_ECC_ENGINE_TYPE_ON_HOST,
-	.ecc_bits	= 1,
-	.bbt_options	= NAND_BBT_USE_FLASH,
-	.timing		= &davinci_evm_nandflash_timing,
-};
-
-static struct resource davinci_evm_nandflash_resource[] = {
-	{
-		.start		= DM644X_ASYNC_EMIF_DATA_CE0_BASE,
-		.end		= DM644X_ASYNC_EMIF_DATA_CE0_BASE + SZ_16M - 1,
-		.flags		= IORESOURCE_MEM,
-	}, {
-		.start		= DM644X_ASYNC_EMIF_CONTROL_BASE,
-		.end		= DM644X_ASYNC_EMIF_CONTROL_BASE + SZ_4K - 1,
-		.flags		= IORESOURCE_MEM,
-	},
-};
-
-static struct resource davinci_evm_aemif_resource[] = {
-	{
-		.start		= DM644X_ASYNC_EMIF_CONTROL_BASE,
-		.end		= DM644X_ASYNC_EMIF_CONTROL_BASE + SZ_4K - 1,
-		.flags		= IORESOURCE_MEM,
-	},
-};
-
-static struct aemif_abus_data davinci_evm_aemif_abus_data[] = {
-	{
-		.cs		= 1,
-	},
-};
-
-static struct platform_device davinci_evm_nandflash_devices[] = {
-	{
-		.name		= "davinci_nand",
-		.id		= 0,
-		.dev		= {
-			.platform_data	= &davinci_evm_nandflash_data,
-		},
-		.num_resources	= ARRAY_SIZE(davinci_evm_nandflash_resource),
-		.resource	= davinci_evm_nandflash_resource,
-	},
-};
-
-static struct aemif_platform_data davinci_evm_aemif_pdata = {
-	.abus_data = davinci_evm_aemif_abus_data,
-	.num_abus_data = ARRAY_SIZE(davinci_evm_aemif_abus_data),
-	.sub_devices = davinci_evm_nandflash_devices,
-	.num_sub_devices = ARRAY_SIZE(davinci_evm_nandflash_devices),
-};
-
-static struct platform_device davinci_evm_aemif_device = {
-	.name			= "ti-aemif",
-	.id			= -1,
-	.dev = {
-		.platform_data	= &davinci_evm_aemif_pdata,
-	},
-	.resource		= davinci_evm_aemif_resource,
-	.num_resources		= ARRAY_SIZE(davinci_evm_aemif_resource),
-};
-
-static u64 davinci_fb_dma_mask = DMA_BIT_MASK(32);
-
-static struct platform_device davinci_fb_device = {
-	.name		= "davincifb",
-	.id		= -1,
-	.dev = {
-		.dma_mask		= &davinci_fb_dma_mask,
-		.coherent_dma_mask      = DMA_BIT_MASK(32),
-	},
-	.num_resources = 0,
-};
-
-static struct tvp514x_platform_data dm644xevm_tvp5146_pdata = {
-	.clk_polarity = 0,
-	.hs_polarity = 1,
-	.vs_polarity = 1
-};
-
-#define TVP514X_STD_ALL	(V4L2_STD_NTSC | V4L2_STD_PAL)
-/* Inputs available at the TVP5146 */
-static struct v4l2_input dm644xevm_tvp5146_inputs[] = {
-	{
-		.index = 0,
-		.name = "Composite",
-		.type = V4L2_INPUT_TYPE_CAMERA,
-		.std = TVP514X_STD_ALL,
-	},
-	{
-		.index = 1,
-		.name = "S-Video",
-		.type = V4L2_INPUT_TYPE_CAMERA,
-		.std = TVP514X_STD_ALL,
-	},
-};
-
-/*
- * this is the route info for connecting each input to decoder
- * ouput that goes to vpfe. There is a one to one correspondence
- * with tvp5146_inputs
- */
-static struct vpfe_route dm644xevm_tvp5146_routes[] = {
-	{
-		.input = INPUT_CVBS_VI2B,
-		.output = OUTPUT_10BIT_422_EMBEDDED_SYNC,
-	},
-	{
-		.input = INPUT_SVIDEO_VI2C_VI1C,
-		.output = OUTPUT_10BIT_422_EMBEDDED_SYNC,
-	},
-};
-
-static struct vpfe_subdev_info dm644xevm_vpfe_sub_devs[] = {
-	{
-		.name = "tvp5146",
-		.grp_id = 0,
-		.num_inputs = ARRAY_SIZE(dm644xevm_tvp5146_inputs),
-		.inputs = dm644xevm_tvp5146_inputs,
-		.routes = dm644xevm_tvp5146_routes,
-		.can_route = 1,
-		.ccdc_if_params = {
-			.if_type = VPFE_BT656,
-			.hdpol = VPFE_PINPOL_POSITIVE,
-			.vdpol = VPFE_PINPOL_POSITIVE,
-		},
-		.board_info = {
-			I2C_BOARD_INFO("tvp5146", 0x5d),
-			.platform_data = &dm644xevm_tvp5146_pdata,
-		},
-	},
-};
-
-static struct vpfe_config dm644xevm_capture_cfg = {
-	.num_subdevs = ARRAY_SIZE(dm644xevm_vpfe_sub_devs),
-	.i2c_adapter_id = 1,
-	.sub_devs = dm644xevm_vpfe_sub_devs,
-	.card_name = "DM6446 EVM",
-	.ccdc = "DM6446 CCDC",
-};
-
-static struct platform_device rtc_dev = {
-	.name           = "rtc_davinci_evm",
-	.id             = -1,
-};
-
-/*----------------------------------------------------------------------*/
-#ifdef CONFIG_I2C
-/*
- * I2C GPIO expanders
- */
-
-#define PCF_Uxx_BASE(x)	(DAVINCI_N_GPIO + ((x) * 8))
-
-
-/* U2 -- LEDs */
-
-static struct gpio_led evm_leds[] = {
-	{ .name = "DS8", .active_low = 1,
-		.default_trigger = "heartbeat", },
-	{ .name = "DS7", .active_low = 1, },
-	{ .name = "DS6", .active_low = 1, },
-	{ .name = "DS5", .active_low = 1, },
-	{ .name = "DS4", .active_low = 1, },
-	{ .name = "DS3", .active_low = 1, },
-	{ .name = "DS2", .active_low = 1,
-		.default_trigger = "mmc0", },
-	{ .name = "DS1", .active_low = 1,
-		.default_trigger = "disk-activity", },
-};
-
-static const struct gpio_led_platform_data evm_led_data = {
-	.num_leds	= ARRAY_SIZE(evm_leds),
-	.leds		= evm_leds,
-};
-
-static struct platform_device *evm_led_dev;
-
-static int
-evm_led_setup(struct i2c_client *client, int gpio, unsigned ngpio, void *c)
-{
-	struct gpio_led *leds = evm_leds;
-	int status;
-
-	while (ngpio--) {
-		leds->gpio = gpio++;
-		leds++;
-	}
-
-	/* what an extremely annoying way to be forced to handle
-	 * device unregistration ...
-	 */
-	evm_led_dev = platform_device_alloc("leds-gpio", 0);
-	platform_device_add_data(evm_led_dev,
-			&evm_led_data, sizeof evm_led_data);
-
-	evm_led_dev->dev.parent = &client->dev;
-	status = platform_device_add(evm_led_dev);
-	if (status < 0) {
-		platform_device_put(evm_led_dev);
-		evm_led_dev = NULL;
-	}
-	return status;
-}
-
-static int
-evm_led_teardown(struct i2c_client *client, int gpio, unsigned ngpio, void *c)
-{
-	if (evm_led_dev) {
-		platform_device_unregister(evm_led_dev);
-		evm_led_dev = NULL;
-	}
-	return 0;
-}
-
-static struct pcf857x_platform_data pcf_data_u2 = {
-	.gpio_base	= PCF_Uxx_BASE(0),
-	.setup		= evm_led_setup,
-	.teardown	= evm_led_teardown,
-};
-
-
-/* U18 - A/V clock generator and user switch */
-
-static int sw_gpio;
-
-static ssize_t
-sw_show(struct device *d, struct device_attribute *a, char *buf)
-{
-	char *s = gpio_get_value_cansleep(sw_gpio) ? "on\n" : "off\n";
-
-	strcpy(buf, s);
-	return strlen(s);
-}
-
-static DEVICE_ATTR(user_sw, S_IRUGO, sw_show, NULL);
-
-static int
-evm_u18_setup(struct i2c_client *client, int gpio, unsigned ngpio, void *c)
-{
-	int	status;
-
-	/* export dip switch option */
-	sw_gpio = gpio + 7;
-	status = gpio_request(sw_gpio, "user_sw");
-	if (status == 0)
-		status = gpio_direction_input(sw_gpio);
-	if (status == 0)
-		status = device_create_file(&client->dev, &dev_attr_user_sw);
-	else
-		gpio_free(sw_gpio);
-	if (status != 0)
-		sw_gpio = -EINVAL;
-
-	/* audio PLL:  48 kHz (vs 44.1 or 32), single rate (vs double) */
-	gpio_request(gpio + 3, "pll_fs2");
-	gpio_direction_output(gpio + 3, 0);
-
-	gpio_request(gpio + 2, "pll_fs1");
-	gpio_direction_output(gpio + 2, 0);
-
-	gpio_request(gpio + 1, "pll_sr");
-	gpio_direction_output(gpio + 1, 0);
-
-	return 0;
-}
-
-static int
-evm_u18_teardown(struct i2c_client *client, int gpio, unsigned ngpio, void *c)
-{
-	gpio_free(gpio + 1);
-	gpio_free(gpio + 2);
-	gpio_free(gpio + 3);
-
-	if (sw_gpio > 0) {
-		device_remove_file(&client->dev, &dev_attr_user_sw);
-		gpio_free(sw_gpio);
-	}
-	return 0;
-}
-
-static struct pcf857x_platform_data pcf_data_u18 = {
-	.gpio_base	= PCF_Uxx_BASE(1),
-	.n_latch	= (1 << 3) | (1 << 2) | (1 << 1),
-	.setup		= evm_u18_setup,
-	.teardown	= evm_u18_teardown,
-};
-
-
-/* U35 - various I/O signals used to manage USB, CF, ATA, etc */
-
-static int
-evm_u35_setup(struct i2c_client *client, int gpio, unsigned ngpio, void *c)
-{
-	/* p0 = nDRV_VBUS (initial:  don't supply it) */
-	gpio_request(gpio + 0, "nDRV_VBUS");
-	gpio_direction_output(gpio + 0, 1);
-
-	/* p1 = VDDIMX_EN */
-	gpio_request(gpio + 1, "VDDIMX_EN");
-	gpio_direction_output(gpio + 1, 1);
-
-	/* p2 = VLYNQ_EN */
-	gpio_request(gpio + 2, "VLYNQ_EN");
-	gpio_direction_output(gpio + 2, 1);
-
-	/* p3 = n3V3_CF_RESET (initial: stay in reset) */
-	gpio_request(gpio + 3, "nCF_RESET");
-	gpio_direction_output(gpio + 3, 0);
-
-	/* (p4 unused) */
-
-	/* p5 = 1V8_WLAN_RESET (initial: stay in reset) */
-	gpio_request(gpio + 5, "WLAN_RESET");
-	gpio_direction_output(gpio + 5, 1);
-
-	/* p6 = nATA_SEL (initial: select) */
-	gpio_request(gpio + 6, "nATA_SEL");
-	gpio_direction_output(gpio + 6, 0);
-
-	/* p7 = nCF_SEL (initial: deselect) */
-	gpio_request(gpio + 7, "nCF_SEL");
-	gpio_direction_output(gpio + 7, 1);
-
-	return 0;
-}
-
-static int
-evm_u35_teardown(struct i2c_client *client, int gpio, unsigned ngpio, void *c)
-{
-	gpio_free(gpio + 7);
-	gpio_free(gpio + 6);
-	gpio_free(gpio + 5);
-	gpio_free(gpio + 3);
-	gpio_free(gpio + 2);
-	gpio_free(gpio + 1);
-	gpio_free(gpio + 0);
-	return 0;
-}
-
-static struct pcf857x_platform_data pcf_data_u35 = {
-	.gpio_base	= PCF_Uxx_BASE(2),
-	.setup		= evm_u35_setup,
-	.teardown	= evm_u35_teardown,
-};
-
-/*----------------------------------------------------------------------*/
-
-/* Most of this EEPROM is unused, but U-Boot uses some data:
- *  - 0x7f00, 6 bytes Ethernet Address
- *  - 0x0039, 1 byte NTSC vs PAL (bit 0x80 == PAL)
- *  - ... newer boards may have more
- */
-
-static struct nvmem_cell_info dm644evm_nvmem_cells[] = {
-	{
-		.name		= "macaddr",
-		.offset		= 0x7f00,
-		.bytes		= ETH_ALEN,
-	}
-};
-
-static struct nvmem_cell_table dm644evm_nvmem_cell_table = {
-	.nvmem_name	= "1-00500",
-	.cells		= dm644evm_nvmem_cells,
-	.ncells		= ARRAY_SIZE(dm644evm_nvmem_cells),
-};
-
-static struct nvmem_cell_lookup dm644evm_nvmem_cell_lookup = {
-	.nvmem_name	= "1-00500",
-	.cell_name	= "macaddr",
-	.dev_id		= "davinci_emac.1",
-	.con_id		= "mac-address",
-};
-
-static const struct property_entry eeprom_properties[] = {
-	PROPERTY_ENTRY_U32("pagesize", 64),
-	{ }
-};
-
-static const struct software_node eeprom_node = {
-	.properties = eeprom_properties,
-};
-
-/*
- * MSP430 supports RTC, card detection, input from IR remote, and
- * a bit more.  It triggers interrupts on GPIO(7) from pressing
- * buttons on the IR remote, and for card detect switches.
- */
-static struct i2c_client *dm6446evm_msp;
-
-static int dm6446evm_msp_probe(struct i2c_client *client)
-{
-	dm6446evm_msp = client;
-	return 0;
-}
-
-static int dm6446evm_msp_remove(struct i2c_client *client)
-{
-	dm6446evm_msp = NULL;
-	return 0;
-}
-
-static const struct i2c_device_id dm6446evm_msp_ids[] = {
-	{ "dm6446evm_msp", 0, },
-	{ /* end of list */ },
-};
-
-static struct i2c_driver dm6446evm_msp_driver = {
-	.driver.name	= "dm6446evm_msp",
-	.id_table	= dm6446evm_msp_ids,
-	.probe_new	= dm6446evm_msp_probe,
-	.remove		= dm6446evm_msp_remove,
-};
-
-static int dm6444evm_msp430_get_pins(void)
-{
-	static const char txbuf[2] = { 2, 4, };
-	char buf[4];
-	struct i2c_msg msg[2] = {
-		{
-			.flags = 0,
-			.len = 2,
-			.buf = (void __force *)txbuf,
-		},
-		{
-			.flags = I2C_M_RD,
-			.len = 4,
-			.buf = buf,
-		},
-	};
-	int status;
-
-	if (!dm6446evm_msp)
-		return -ENXIO;
-
-	msg[0].addr = dm6446evm_msp->addr;
-	msg[1].addr = dm6446evm_msp->addr;
-
-	/* Command 4 == get input state, returns port 2 and port3 data
-	 *   S Addr W [A] len=2 [A] cmd=4 [A]
-	 *   RS Addr R [A] [len=4] A [cmd=4] A [port2] A [port3] N P
-	 */
-	status = i2c_transfer(dm6446evm_msp->adapter, msg, 2);
-	if (status < 0)
-		return status;
-
-	dev_dbg(&dm6446evm_msp->dev, "PINS: %4ph\n", buf);
-
-	return (buf[3] << 8) | buf[2];
-}
-
-static int dm6444evm_mmc_get_cd(int module)
-{
-	int status = dm6444evm_msp430_get_pins();
-
-	return (status < 0) ? status : !(status & BIT(1));
-}
-
-static int dm6444evm_mmc_get_ro(int module)
-{
-	int status = dm6444evm_msp430_get_pins();
-
-	return (status < 0) ? status : status & BIT(6 + 8);
-}
-
-static struct davinci_mmc_config dm6446evm_mmc_config = {
-	.get_cd		= dm6444evm_mmc_get_cd,
-	.get_ro		= dm6444evm_mmc_get_ro,
-	.wires		= 4,
-};
-
-static struct i2c_board_info __initdata i2c_info[] =  {
-	{
-		I2C_BOARD_INFO("dm6446evm_msp", 0x23),
-	},
-	{
-		I2C_BOARD_INFO("pcf8574", 0x38),
-		.platform_data	= &pcf_data_u2,
-	},
-	{
-		I2C_BOARD_INFO("pcf8574", 0x39),
-		.platform_data	= &pcf_data_u18,
-	},
-	{
-		I2C_BOARD_INFO("pcf8574", 0x3a),
-		.platform_data	= &pcf_data_u35,
-	},
-	{
-		I2C_BOARD_INFO("24c256", 0x50),
-		.swnode = &eeprom_node,
-	},
-	{
-		I2C_BOARD_INFO("tlv320aic33", 0x1b),
-	},
-};
-
-#define DM644X_I2C_SDA_PIN	GPIO_TO_PIN(2, 12)
-#define DM644X_I2C_SCL_PIN	GPIO_TO_PIN(2, 11)
-
-static struct gpiod_lookup_table i2c_recovery_gpiod_table = {
-	.dev_id = "i2c_davinci.1",
-	.table = {
-		GPIO_LOOKUP("davinci_gpio", DM644X_I2C_SDA_PIN, "sda",
-			    GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN),
-		GPIO_LOOKUP("davinci_gpio", DM644X_I2C_SCL_PIN, "scl",
-			    GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN),
-		{ }
-	},
-};
-
-/* The msp430 uses a slow bitbanged I2C implementation (ergo 20 KHz),
- * which requires 100 usec of idle bus after i2c writes sent to it.
- */
-static struct davinci_i2c_platform_data i2c_pdata = {
-	.bus_freq	= 20 /* kHz */,
-	.bus_delay	= 100 /* usec */,
-	.gpio_recovery	= true,
-};
-
-static void __init evm_init_i2c(void)
-{
-	gpiod_add_lookup_table(&i2c_recovery_gpiod_table);
-	davinci_init_i2c(&i2c_pdata);
-	i2c_add_driver(&dm6446evm_msp_driver);
-	i2c_register_board_info(1, i2c_info, ARRAY_SIZE(i2c_info));
-}
-#endif
-
-/* Fixed regulator support */
-static struct regulator_consumer_supply fixed_supplies_3_3v[] = {
-	/* Baseboard 3.3V: 5V -> TPS54310PWP -> 3.3V */
-	REGULATOR_SUPPLY("AVDD", "1-001b"),
-	REGULATOR_SUPPLY("DRVDD", "1-001b"),
-};
-
-static struct regulator_consumer_supply fixed_supplies_1_8v[] = {
-	/* Baseboard 1.8V: 5V -> TPS54310PWP -> 1.8V */
-	REGULATOR_SUPPLY("IOVDD", "1-001b"),
-	REGULATOR_SUPPLY("DVDD", "1-001b"),
-};
-
-#define VENC_STD_ALL	(V4L2_STD_NTSC | V4L2_STD_PAL)
-
-/* venc standard timings */
-static struct vpbe_enc_mode_info dm644xevm_enc_std_timing[] = {
-	{
-		.name		= "ntsc",
-		.timings_type	= VPBE_ENC_STD,
-		.std_id		= V4L2_STD_NTSC,
-		.interlaced	= 1,
-		.xres		= 720,
-		.yres		= 480,
-		.aspect		= {11, 10},
-		.fps		= {30000, 1001},
-		.left_margin	= 0x79,
-		.upper_margin	= 0x10,
-	},
-	{
-		.name		= "pal",
-		.timings_type	= VPBE_ENC_STD,
-		.std_id		= V4L2_STD_PAL,
-		.interlaced	= 1,
-		.xres		= 720,
-		.yres		= 576,
-		.aspect		= {54, 59},
-		.fps		= {25, 1},
-		.left_margin	= 0x7e,
-		.upper_margin	= 0x16,
-	},
-};
-
-/* venc dv preset timings */
-static struct vpbe_enc_mode_info dm644xevm_enc_preset_timing[] = {
-	{
-		.name		= "480p59_94",
-		.timings_type	= VPBE_ENC_DV_TIMINGS,
-		.dv_timings	= V4L2_DV_BT_CEA_720X480P59_94,
-		.interlaced	= 0,
-		.xres		= 720,
-		.yres		= 480,
-		.aspect		= {1, 1},
-		.fps		= {5994, 100},
-		.left_margin	= 0x80,
-		.upper_margin	= 0x20,
-	},
-	{
-		.name		= "576p50",
-		.timings_type	= VPBE_ENC_DV_TIMINGS,
-		.dv_timings	= V4L2_DV_BT_CEA_720X576P50,
-		.interlaced	= 0,
-		.xres		= 720,
-		.yres		= 576,
-		.aspect		= {1, 1},
-		.fps		= {50, 1},
-		.left_margin	= 0x7e,
-		.upper_margin	= 0x30,
-	},
-};
-
-/*
- * The outputs available from VPBE + encoders. Keep the order same
- * as that of encoders. First those from venc followed by that from
- * encoders. Index in the output refers to index on a particular encoder.
- * Driver uses this index to pass it to encoder when it supports more
- * than one output. Userspace applications use index of the array to
- * set an output.
- */
-static struct vpbe_output dm644xevm_vpbe_outputs[] = {
-	{
-		.output		= {
-			.index		= 0,
-			.name		= "Composite",
-			.type		= V4L2_OUTPUT_TYPE_ANALOG,
-			.std		= VENC_STD_ALL,
-			.capabilities	= V4L2_OUT_CAP_STD,
-		},
-		.subdev_name	= DM644X_VPBE_VENC_SUBDEV_NAME,
-		.default_mode	= "ntsc",
-		.num_modes	= ARRAY_SIZE(dm644xevm_enc_std_timing),
-		.modes		= dm644xevm_enc_std_timing,
-	},
-	{
-		.output		= {
-			.index		= 1,
-			.name		= "Component",
-			.type		= V4L2_OUTPUT_TYPE_ANALOG,
-			.capabilities	= V4L2_OUT_CAP_DV_TIMINGS,
-		},
-		.subdev_name	= DM644X_VPBE_VENC_SUBDEV_NAME,
-		.default_mode	= "480p59_94",
-		.num_modes	= ARRAY_SIZE(dm644xevm_enc_preset_timing),
-		.modes		= dm644xevm_enc_preset_timing,
-	},
-};
-
-static struct vpbe_config dm644xevm_display_cfg = {
-	.module_name	= "dm644x-vpbe-display",
-	.i2c_adapter_id	= 1,
-	.osd		= {
-		.module_name	= DM644X_VPBE_OSD_SUBDEV_NAME,
-	},
-	.venc		= {
-		.module_name	= DM644X_VPBE_VENC_SUBDEV_NAME,
-	},
-	.num_outputs	= ARRAY_SIZE(dm644xevm_vpbe_outputs),
-	.outputs	= dm644xevm_vpbe_outputs,
-};
-
-static struct platform_device *davinci_evm_devices[] __initdata = {
-	&davinci_fb_device,
-	&rtc_dev,
-};
-
-static void __init
-davinci_evm_map_io(void)
-{
-	dm644x_init();
-}
-
-static int davinci_phy_fixup(struct phy_device *phydev)
-{
-	unsigned int control;
-	/* CRITICAL: Fix for increasing PHY signal drive strength for
-	 * TX lockup issue. On DaVinci EVM, the Intel LXT971 PHY
-	 * signal strength was low causing  TX to fail randomly. The
-	 * fix is to Set bit 11 (Increased MII drive strength) of PHY
-	 * register 26 (Digital Config register) on this phy. */
-	control = phy_read(phydev, 26);
-	phy_write(phydev, 26, (control | 0x800));
-	return 0;
-}
-
-#define HAS_ATA		(IS_ENABLED(CONFIG_BLK_DEV_PALMCHIP_BK3710) || \
-			 IS_ENABLED(CONFIG_PATA_BK3710))
-
-#define HAS_NOR		IS_ENABLED(CONFIG_MTD_PHYSMAP)
-
-#define HAS_NAND	IS_ENABLED(CONFIG_MTD_NAND_DAVINCI)
-
-#define GPIO_nVBUS_DRV		160
-
-static struct gpiod_lookup_table dm644evm_usb_gpio_table = {
-	.dev_id = "musb-davinci",
-	.table = {
-		GPIO_LOOKUP("davinci_gpio", GPIO_nVBUS_DRV, NULL,
-			    GPIO_ACTIVE_HIGH),
-		{ }
-	},
-};
-
-static __init void davinci_evm_init(void)
-{
-	int ret;
-	struct clk *aemif_clk;
-	struct davinci_soc_info *soc_info = &davinci_soc_info;
-
-	dm644x_register_clocks();
-
-	regulator_register_always_on(0, "fixed-dummy", fixed_supplies_1_8v,
-				     ARRAY_SIZE(fixed_supplies_1_8v), 1800000);
-	regulator_register_always_on(1, "fixed-dummy", fixed_supplies_3_3v,
-				     ARRAY_SIZE(fixed_supplies_3_3v), 3300000);
-
-	dm644x_init_devices();
-
-	ret = dm644x_gpio_register();
-	if (ret)
-		pr_warn("%s: GPIO init failed: %d\n", __func__, ret);
-
-	aemif_clk = clk_get(NULL, "aemif");
-	clk_prepare_enable(aemif_clk);
-
-	if (HAS_ATA) {
-		if (HAS_NAND || HAS_NOR)
-			pr_warn("WARNING: both IDE and Flash are enabled, but they share AEMIF pins\n"
-				"\tDisable IDE for NAND/NOR support\n");
-		davinci_init_ide();
-	} else if (HAS_NAND || HAS_NOR) {
-		davinci_cfg_reg(DM644X_HPIEN_DISABLE);
-		davinci_cfg_reg(DM644X_ATAEN_DISABLE);
-
-		/* only one device will be jumpered and detected */
-		if (HAS_NAND) {
-			platform_device_register(&davinci_evm_aemif_device);
-#ifdef CONFIG_I2C
-			evm_leds[7].default_trigger = "nand-disk";
-#endif
-			if (HAS_NOR)
-				pr_warn("WARNING: both NAND and NOR flash are enabled; disable one of them.\n");
-		} else if (HAS_NOR)
-			platform_device_register(&davinci_evm_norflash_device);
-	}
-
-	platform_add_devices(davinci_evm_devices,
-			     ARRAY_SIZE(davinci_evm_devices));
-#ifdef CONFIG_I2C
-	nvmem_add_cell_table(&dm644evm_nvmem_cell_table);
-	nvmem_add_cell_lookups(&dm644evm_nvmem_cell_lookup, 1);
-	evm_init_i2c();
-	davinci_setup_mmc(0, &dm6446evm_mmc_config);
-#endif
-	dm644x_init_video(&dm644xevm_capture_cfg, &dm644xevm_display_cfg);
-
-	davinci_serial_init(dm644x_serial_device);
-	dm644x_init_asp();
-
-	/* irlml6401 switches over 1A, in under 8 msec */
-	gpiod_add_lookup_table(&dm644evm_usb_gpio_table);
-	davinci_setup_usb(1000, 8);
-
-	if (IS_BUILTIN(CONFIG_PHYLIB)) {
-		soc_info->emac_pdata->phy_id = DM644X_EVM_PHY_ID;
-		/* Register the fixup for PHY on DaVinci */
-		phy_register_fixup_for_uid(LXT971_PHY_ID, LXT971_PHY_MASK,
-						davinci_phy_fixup);
-	}
-}
-
-MACHINE_START(DAVINCI_EVM, "DaVinci DM644x EVM")
-	/* Maintainer: MontaVista Software <source@mvista.com> */
-	.atag_offset  = 0x100,
-	.map_io	      = davinci_evm_map_io,
-	.init_irq     = dm644x_init_irq,
-	.init_time	= dm644x_init_time,
-	.init_machine = davinci_evm_init,
-	.init_late	= davinci_init_late,
-	.dma_zone_size	= SZ_128M,
-MACHINE_END
diff --git a/arch/arm/mach-davinci/board-dm646x-evm.c b/arch/arm/mach-davinci/board-dm646x-evm.c
deleted file mode 100644
index ee91d81ebbfd..000000000000
--- a/arch/arm/mach-davinci/board-dm646x-evm.c
+++ /dev/null
@@ -1,876 +0,0 @@
-/*
- * TI DaVinci DM646X EVM board
- *
- * Derived from: arch/arm/mach-davinci/board-evm.c
- * Copyright (C) 2006 Texas Instruments.
- *
- * (C) 2007-2008, MontaVista Software, Inc.
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2. This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
- *
- */
-
-/**************************************************************************
- * Included Files
- **************************************************************************/
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/leds.h>
-#include <linux/gpio.h>
-#include <linux/platform_device.h>
-#include <linux/i2c.h>
-#include <linux/property.h>
-#include <linux/platform_data/pcf857x.h>
-#include <linux/platform_data/ti-aemif.h>
-
-#include <media/i2c/tvp514x.h>
-#include <media/i2c/adv7343.h>
-
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/rawnand.h>
-#include <linux/mtd/partitions.h>
-#include <linux/nvmem-provider.h>
-#include <linux/clk.h>
-#include <linux/export.h>
-#include <linux/platform_data/gpio-davinci.h>
-#include <linux/platform_data/i2c-davinci.h>
-#include <linux/platform_data/mtd-davinci.h>
-#include <linux/platform_data/mtd-davinci-aemif.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-
-#include <mach/common.h>
-#include <mach/serial.h>
-
-#include "davinci.h"
-#include "irqs.h"
-
-#define NAND_BLOCK_SIZE		SZ_128K
-
-/* Note: We are setting first partition as 'bootloader' constituting UBL, U-Boot
- * and U-Boot environment this avoids dependency on any particular combination
- * of UBL, U-Boot or flashing tools etc.
- */
-static struct mtd_partition davinci_nand_partitions[] = {
-	{
-		/* UBL, U-Boot with environment */
-		.name		= "bootloader",
-		.offset		= MTDPART_OFS_APPEND,
-		.size		= 16 * NAND_BLOCK_SIZE,
-		.mask_flags	= MTD_WRITEABLE,	/* force read-only */
-	}, {
-		.name		= "kernel",
-		.offset		= MTDPART_OFS_APPEND,
-		.size		= SZ_4M,
-		.mask_flags	= 0,
-	}, {
-		.name		= "filesystem",
-		.offset		= MTDPART_OFS_APPEND,
-		.size		= MTDPART_SIZ_FULL,
-		.mask_flags	= 0,
-	}
-};
-
-static struct davinci_aemif_timing dm6467tevm_nandflash_timing = {
-	.wsetup		= 29,
-	.wstrobe	= 24,
-	.whold		= 14,
-	.rsetup		= 19,
-	.rstrobe	= 33,
-	.rhold		= 0,
-	.ta		= 29,
-};
-
-static struct davinci_nand_pdata davinci_nand_data = {
-	.core_chipsel		= 0,
-	.mask_cle 		= 0x80000,
-	.mask_ale 		= 0x40000,
-	.parts			= davinci_nand_partitions,
-	.nr_parts		= ARRAY_SIZE(davinci_nand_partitions),
-	.engine_type		= NAND_ECC_ENGINE_TYPE_ON_HOST,
-	.ecc_bits		= 1,
-	.options		= 0,
-};
-
-static struct resource davinci_nand_resources[] = {
-	{
-		.start		= DM646X_ASYNC_EMIF_CS2_SPACE_BASE,
-		.end		= DM646X_ASYNC_EMIF_CS2_SPACE_BASE + SZ_32M - 1,
-		.flags		= IORESOURCE_MEM,
-	}, {
-		.start		= DM646X_ASYNC_EMIF_CONTROL_BASE,
-		.end		= DM646X_ASYNC_EMIF_CONTROL_BASE + SZ_4K - 1,
-		.flags		= IORESOURCE_MEM,
-	},
-};
-
-static struct platform_device davinci_aemif_devices[] = {
-	{
-		.name		= "davinci_nand",
-		.id		= 0,
-		.num_resources	= ARRAY_SIZE(davinci_nand_resources),
-		.resource	= davinci_nand_resources,
-		.dev		= {
-			.platform_data	= &davinci_nand_data,
-		},
-	},
-};
-
-static struct resource davinci_aemif_resources[] = {
-	{
-		.start	= DM646X_ASYNC_EMIF_CONTROL_BASE,
-		.end	= DM646X_ASYNC_EMIF_CONTROL_BASE + SZ_4K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-};
-
-static struct aemif_abus_data davinci_aemif_abus_data[] = {
-	{
-		.cs	= 1,
-	},
-};
-
-static struct aemif_platform_data davinci_aemif_pdata = {
-	.abus_data		= davinci_aemif_abus_data,
-	.num_abus_data		= ARRAY_SIZE(davinci_aemif_abus_data),
-	.sub_devices		= davinci_aemif_devices,
-	.num_sub_devices	= ARRAY_SIZE(davinci_aemif_devices),
-};
-
-static struct platform_device davinci_aemif_device = {
-	.name		= "ti-aemif",
-	.id		= -1,
-	.dev = {
-		.platform_data	= &davinci_aemif_pdata,
-	},
-	.resource	= davinci_aemif_resources,
-	.num_resources	= ARRAY_SIZE(davinci_aemif_resources),
-};
-
-#define HAS_ATA		(IS_ENABLED(CONFIG_BLK_DEV_PALMCHIP_BK3710) || \
-			 IS_ENABLED(CONFIG_PATA_BK3710))
-
-#ifdef CONFIG_I2C
-/* CPLD Register 0 bits to control ATA */
-#define DM646X_EVM_ATA_RST		BIT(0)
-#define DM646X_EVM_ATA_PWD		BIT(1)
-
-/* CPLD Register 0 Client: used for I/O Control */
-static int cpld_reg0_probe(struct i2c_client *client)
-{
-	if (HAS_ATA) {
-		u8 data;
-		struct i2c_msg msg[2] = {
-			{
-				.addr = client->addr,
-				.flags = I2C_M_RD,
-				.len = 1,
-				.buf = &data,
-			},
-			{
-				.addr = client->addr,
-				.flags = 0,
-				.len = 1,
-				.buf = &data,
-			},
-		};
-
-		/* Clear ATA_RSTn and ATA_PWD bits to enable ATA operation. */
-		i2c_transfer(client->adapter, msg, 1);
-		data &= ~(DM646X_EVM_ATA_RST | DM646X_EVM_ATA_PWD);
-		i2c_transfer(client->adapter, msg + 1, 1);
-	}
-
-	return 0;
-}
-
-static const struct i2c_device_id cpld_reg_ids[] = {
-	{ "cpld_reg0", 0, },
-	{ },
-};
-
-static struct i2c_driver dm6467evm_cpld_driver = {
-	.driver.name	= "cpld_reg0",
-	.id_table	= cpld_reg_ids,
-	.probe_new	= cpld_reg0_probe,
-};
-
-/* LEDS */
-
-static struct gpio_led evm_leds[] = {
-	{ .name = "DS1", .active_low = 1, },
-	{ .name = "DS2", .active_low = 1, },
-	{ .name = "DS3", .active_low = 1, },
-	{ .name = "DS4", .active_low = 1, },
-};
-
-static const struct gpio_led_platform_data evm_led_data = {
-	.num_leds = ARRAY_SIZE(evm_leds),
-	.leds     = evm_leds,
-};
-
-static struct platform_device *evm_led_dev;
-
-static int evm_led_setup(struct i2c_client *client, int gpio,
-			unsigned int ngpio, void *c)
-{
-	struct gpio_led *leds = evm_leds;
-	int status;
-
-	while (ngpio--) {
-		leds->gpio = gpio++;
-		leds++;
-	}
-
-	evm_led_dev = platform_device_alloc("leds-gpio", 0);
-	platform_device_add_data(evm_led_dev, &evm_led_data,
-				sizeof(evm_led_data));
-
-	evm_led_dev->dev.parent = &client->dev;
-	status = platform_device_add(evm_led_dev);
-	if (status < 0) {
-		platform_device_put(evm_led_dev);
-		evm_led_dev = NULL;
-	}
-	return status;
-}
-
-static int evm_led_teardown(struct i2c_client *client, int gpio,
-				unsigned ngpio, void *c)
-{
-	if (evm_led_dev) {
-		platform_device_unregister(evm_led_dev);
-		evm_led_dev = NULL;
-	}
-	return 0;
-}
-
-static int evm_sw_gpio[4] = { -EINVAL, -EINVAL, -EINVAL, -EINVAL };
-
-static int evm_sw_setup(struct i2c_client *client, int gpio,
-			unsigned ngpio, void *c)
-{
-	int status;
-	int i;
-	char label[10];
-
-	for (i = 0; i < 4; ++i) {
-		snprintf(label, 10, "user_sw%d", i);
-		status = gpio_request(gpio, label);
-		if (status)
-			goto out_free;
-		evm_sw_gpio[i] = gpio++;
-
-		status = gpio_direction_input(evm_sw_gpio[i]);
-		if (status)
-			goto out_free;
-
-		status = gpio_export(evm_sw_gpio[i], 0);
-		if (status)
-			goto out_free;
-	}
-	return 0;
-
-out_free:
-	for (i = 0; i < 4; ++i) {
-		if (evm_sw_gpio[i] != -EINVAL) {
-			gpio_free(evm_sw_gpio[i]);
-			evm_sw_gpio[i] = -EINVAL;
-		}
-	}
-	return status;
-}
-
-static int evm_sw_teardown(struct i2c_client *client, int gpio,
-			unsigned ngpio, void *c)
-{
-	int i;
-
-	for (i = 0; i < 4; ++i) {
-		if (evm_sw_gpio[i] != -EINVAL) {
-			gpio_unexport(evm_sw_gpio[i]);
-			gpio_free(evm_sw_gpio[i]);
-			evm_sw_gpio[i] = -EINVAL;
-		}
-	}
-	return 0;
-}
-
-static int evm_pcf_setup(struct i2c_client *client, int gpio,
-			unsigned int ngpio, void *c)
-{
-	int status;
-
-	if (ngpio < 8)
-		return -EINVAL;
-
-	status = evm_sw_setup(client, gpio, 4, c);
-	if (status)
-		return status;
-
-	return evm_led_setup(client, gpio+4, 4, c);
-}
-
-static int evm_pcf_teardown(struct i2c_client *client, int gpio,
-			unsigned int ngpio, void *c)
-{
-	BUG_ON(ngpio < 8);
-
-	evm_sw_teardown(client, gpio, 4, c);
-	evm_led_teardown(client, gpio+4, 4, c);
-
-	return 0;
-}
-
-static struct pcf857x_platform_data pcf_data = {
-	.gpio_base	= DAVINCI_N_GPIO+1,
-	.setup		= evm_pcf_setup,
-	.teardown	= evm_pcf_teardown,
-};
-
-/* Most of this EEPROM is unused, but U-Boot uses some data:
- *  - 0x7f00, 6 bytes Ethernet Address
- *  - ... newer boards may have more
- */
-
-static struct nvmem_cell_info dm646x_evm_nvmem_cells[] = {
-	{
-		.name		= "macaddr",
-		.offset		= 0x7f00,
-		.bytes		= ETH_ALEN,
-	}
-};
-
-static struct nvmem_cell_table dm646x_evm_nvmem_cell_table = {
-	.nvmem_name	= "1-00500",
-	.cells		= dm646x_evm_nvmem_cells,
-	.ncells		= ARRAY_SIZE(dm646x_evm_nvmem_cells),
-};
-
-static struct nvmem_cell_lookup dm646x_evm_nvmem_cell_lookup = {
-	.nvmem_name	= "1-00500",
-	.cell_name	= "macaddr",
-	.dev_id		= "davinci_emac.1",
-	.con_id		= "mac-address",
-};
-
-static const struct property_entry eeprom_properties[] = {
-	PROPERTY_ENTRY_U32("pagesize", 64),
-	{ }
-};
-
-static const struct software_node eeprom_node = {
-	.properties = eeprom_properties,
-};
-#endif
-
-static u8 dm646x_iis_serializer_direction[] = {
-       TX_MODE, RX_MODE, INACTIVE_MODE, INACTIVE_MODE,
-};
-
-static u8 dm646x_dit_serializer_direction[] = {
-       TX_MODE,
-};
-
-static struct snd_platform_data dm646x_evm_snd_data[] = {
-	{
-		.tx_dma_offset  = 0x400,
-		.rx_dma_offset  = 0x400,
-		.op_mode        = DAVINCI_MCASP_IIS_MODE,
-		.num_serializer = ARRAY_SIZE(dm646x_iis_serializer_direction),
-		.tdm_slots      = 2,
-		.serial_dir     = dm646x_iis_serializer_direction,
-		.asp_chan_q     = EVENTQ_0,
-	},
-	{
-		.tx_dma_offset  = 0x400,
-		.rx_dma_offset  = 0,
-		.op_mode        = DAVINCI_MCASP_DIT_MODE,
-		.num_serializer = ARRAY_SIZE(dm646x_dit_serializer_direction),
-		.tdm_slots      = 32,
-		.serial_dir     = dm646x_dit_serializer_direction,
-		.asp_chan_q     = EVENTQ_0,
-	},
-};
-
-#ifdef CONFIG_I2C
-static struct i2c_client *cpld_client;
-
-static int cpld_video_probe(struct i2c_client *client)
-{
-	cpld_client = client;
-	return 0;
-}
-
-static int cpld_video_remove(struct i2c_client *client)
-{
-	cpld_client = NULL;
-	return 0;
-}
-
-static const struct i2c_device_id cpld_video_id[] = {
-	{ "cpld_video", 0 },
-	{ }
-};
-
-static struct i2c_driver cpld_video_driver = {
-	.driver = {
-		.name	= "cpld_video",
-	},
-	.probe_new	= cpld_video_probe,
-	.remove		= cpld_video_remove,
-	.id_table	= cpld_video_id,
-};
-
-static void evm_init_cpld(void)
-{
-	i2c_add_driver(&cpld_video_driver);
-}
-
-static struct i2c_board_info __initdata i2c_info[] =  {
-	{
-		I2C_BOARD_INFO("24c256", 0x50),
-		.swnode = &eeprom_node,
-	},
-	{
-		I2C_BOARD_INFO("pcf8574a", 0x38),
-		.platform_data	= &pcf_data,
-	},
-	{
-		I2C_BOARD_INFO("cpld_reg0", 0x3a),
-	},
-	{
-		I2C_BOARD_INFO("tlv320aic33", 0x18),
-	},
-	{
-		I2C_BOARD_INFO("cpld_video", 0x3b),
-	},
-};
-
-static struct davinci_i2c_platform_data i2c_pdata = {
-	.bus_freq       = 100 /* kHz */,
-	.bus_delay      = 0 /* usec */,
-};
-
-#define VCH2CLK_MASK		(BIT_MASK(10) | BIT_MASK(9) | BIT_MASK(8))
-#define VCH2CLK_SYSCLK8		(BIT(9))
-#define VCH2CLK_AUXCLK		(BIT(9) | BIT(8))
-#define VCH3CLK_MASK		(BIT_MASK(14) | BIT_MASK(13) | BIT_MASK(12))
-#define VCH3CLK_SYSCLK8		(BIT(13))
-#define VCH3CLK_AUXCLK		(BIT(14) | BIT(13))
-
-#define VIDCH2CLK		(BIT(10))
-#define VIDCH3CLK		(BIT(11))
-#define VIDCH1CLK		(BIT(4))
-#define TVP7002_INPUT		(BIT(4))
-#define TVP5147_INPUT		(~BIT(4))
-#define VPIF_INPUT_ONE_CHANNEL	(BIT(5))
-#define VPIF_INPUT_TWO_CHANNEL	(~BIT(5))
-#define TVP5147_CH0		"tvp514x-0"
-#define TVP5147_CH1		"tvp514x-1"
-
-/* spin lock for updating above registers */
-static spinlock_t vpif_reg_lock;
-
-static int set_vpif_clock(int mux_mode, int hd)
-{
-	unsigned long flags;
-	unsigned int value;
-	int val = 0;
-	int err = 0;
-
-	if (!cpld_client)
-		return -ENXIO;
-
-	/* disable the clock */
-	spin_lock_irqsave(&vpif_reg_lock, flags);
-	value = __raw_readl(DAVINCI_SYSMOD_VIRT(SYSMOD_VSCLKDIS));
-	value |= (VIDCH3CLK | VIDCH2CLK);
-	__raw_writel(value, DAVINCI_SYSMOD_VIRT(SYSMOD_VSCLKDIS));
-	spin_unlock_irqrestore(&vpif_reg_lock, flags);
-
-	val = i2c_smbus_read_byte(cpld_client);
-	if (val < 0)
-		return val;
-
-	if (mux_mode == 1)
-		val &= ~0x40;
-	else
-		val |= 0x40;
-
-	err = i2c_smbus_write_byte(cpld_client, val);
-	if (err)
-		return err;
-
-	value = __raw_readl(DAVINCI_SYSMOD_VIRT(SYSMOD_VIDCLKCTL));
-	value &= ~(VCH2CLK_MASK);
-	value &= ~(VCH3CLK_MASK);
-
-	if (hd >= 1)
-		value |= (VCH2CLK_SYSCLK8 | VCH3CLK_SYSCLK8);
-	else
-		value |= (VCH2CLK_AUXCLK | VCH3CLK_AUXCLK);
-
-	__raw_writel(value, DAVINCI_SYSMOD_VIRT(SYSMOD_VIDCLKCTL));
-
-	spin_lock_irqsave(&vpif_reg_lock, flags);
-	value = __raw_readl(DAVINCI_SYSMOD_VIRT(SYSMOD_VSCLKDIS));
-	/* enable the clock */
-	value &= ~(VIDCH3CLK | VIDCH2CLK);
-	__raw_writel(value, DAVINCI_SYSMOD_VIRT(SYSMOD_VSCLKDIS));
-	spin_unlock_irqrestore(&vpif_reg_lock, flags);
-
-	return 0;
-}
-
-static struct vpif_subdev_info dm646x_vpif_subdev[] = {
-	{
-		.name	= "adv7343",
-		.board_info = {
-			I2C_BOARD_INFO("adv7343", 0x2a),
-		},
-	},
-	{
-		.name	= "ths7303",
-		.board_info = {
-			I2C_BOARD_INFO("ths7303", 0x2c),
-		},
-	},
-};
-
-static const struct vpif_output dm6467_ch0_outputs[] = {
-	{
-		.output = {
-			.index = 0,
-			.name = "Composite",
-			.type = V4L2_OUTPUT_TYPE_ANALOG,
-			.capabilities = V4L2_OUT_CAP_STD,
-			.std = V4L2_STD_ALL,
-		},
-		.subdev_name = "adv7343",
-		.output_route = ADV7343_COMPOSITE_ID,
-	},
-	{
-		.output = {
-			.index = 1,
-			.name = "Component",
-			.type = V4L2_OUTPUT_TYPE_ANALOG,
-			.capabilities = V4L2_OUT_CAP_DV_TIMINGS,
-		},
-		.subdev_name = "adv7343",
-		.output_route = ADV7343_COMPONENT_ID,
-	},
-	{
-		.output = {
-			.index = 2,
-			.name = "S-Video",
-			.type = V4L2_OUTPUT_TYPE_ANALOG,
-			.capabilities = V4L2_OUT_CAP_STD,
-			.std = V4L2_STD_ALL,
-		},
-		.subdev_name = "adv7343",
-		.output_route = ADV7343_SVIDEO_ID,
-	},
-};
-
-static struct vpif_display_config dm646x_vpif_display_config = {
-	.set_clock	= set_vpif_clock,
-	.subdevinfo	= dm646x_vpif_subdev,
-	.subdev_count	= ARRAY_SIZE(dm646x_vpif_subdev),
-	.i2c_adapter_id = 1,
-	.chan_config[0] = {
-		.outputs = dm6467_ch0_outputs,
-		.output_count = ARRAY_SIZE(dm6467_ch0_outputs),
-	},
-	.card_name	= "DM646x EVM Video Display",
-};
-
-/**
- * setup_vpif_input_path()
- * @channel: channel id (0 - CH0, 1 - CH1)
- * @sub_dev_name: ptr sub device name
- *
- * This will set vpif input to capture data from tvp514x or
- * tvp7002.
- */
-static int setup_vpif_input_path(int channel, const char *sub_dev_name)
-{
-	int err = 0;
-	int val;
-
-	/* for channel 1, we don't do anything */
-	if (channel != 0)
-		return 0;
-
-	if (!cpld_client)
-		return -ENXIO;
-
-	val = i2c_smbus_read_byte(cpld_client);
-	if (val < 0)
-		return val;
-
-	if (!strcmp(sub_dev_name, TVP5147_CH0) ||
-	    !strcmp(sub_dev_name, TVP5147_CH1))
-		val &= TVP5147_INPUT;
-	else
-		val |= TVP7002_INPUT;
-
-	err = i2c_smbus_write_byte(cpld_client, val);
-	if (err)
-		return err;
-	return 0;
-}
-
-/**
- * setup_vpif_input_channel_mode()
- * @mux_mode:  mux mode. 0 - 1 channel or (1) - 2 channel
- *
- * This will setup input mode to one channel (TVP7002) or 2 channel (TVP5147)
- */
-static int setup_vpif_input_channel_mode(int mux_mode)
-{
-	unsigned long flags;
-	int err = 0;
-	int val;
-	u32 value;
-
-	if (!cpld_client)
-		return -ENXIO;
-
-	val = i2c_smbus_read_byte(cpld_client);
-	if (val < 0)
-		return val;
-
-	spin_lock_irqsave(&vpif_reg_lock, flags);
-	value = __raw_readl(DAVINCI_SYSMOD_VIRT(SYSMOD_VIDCLKCTL));
-	if (mux_mode) {
-		val &= VPIF_INPUT_TWO_CHANNEL;
-		value |= VIDCH1CLK;
-	} else {
-		val |= VPIF_INPUT_ONE_CHANNEL;
-		value &= ~VIDCH1CLK;
-	}
-	__raw_writel(value, DAVINCI_SYSMOD_VIRT(SYSMOD_VIDCLKCTL));
-	spin_unlock_irqrestore(&vpif_reg_lock, flags);
-
-	err = i2c_smbus_write_byte(cpld_client, val);
-	if (err)
-		return err;
-
-	return 0;
-}
-
-static struct tvp514x_platform_data tvp5146_pdata = {
-	.clk_polarity = 0,
-	.hs_polarity = 1,
-	.vs_polarity = 1
-};
-
-#define TVP514X_STD_ALL (V4L2_STD_NTSC | V4L2_STD_PAL)
-
-static struct vpif_subdev_info vpif_capture_sdev_info[] = {
-	{
-		.name	= TVP5147_CH0,
-		.board_info = {
-			I2C_BOARD_INFO("tvp5146", 0x5d),
-			.platform_data = &tvp5146_pdata,
-		},
-	},
-	{
-		.name	= TVP5147_CH1,
-		.board_info = {
-			I2C_BOARD_INFO("tvp5146", 0x5c),
-			.platform_data = &tvp5146_pdata,
-		},
-	},
-};
-
-static struct vpif_input dm6467_ch0_inputs[] = {
-	{
-		.input = {
-			.index = 0,
-			.name = "Composite",
-			.type = V4L2_INPUT_TYPE_CAMERA,
-			.capabilities = V4L2_IN_CAP_STD,
-			.std = TVP514X_STD_ALL,
-		},
-		.subdev_name = TVP5147_CH0,
-		.input_route = INPUT_CVBS_VI2B,
-		.output_route = OUTPUT_10BIT_422_EMBEDDED_SYNC,
-	},
-};
-
-static struct vpif_input dm6467_ch1_inputs[] = {
-       {
-		.input = {
-			.index = 0,
-			.name = "S-Video",
-			.type = V4L2_INPUT_TYPE_CAMERA,
-			.capabilities = V4L2_IN_CAP_STD,
-			.std = TVP514X_STD_ALL,
-		},
-		.subdev_name = TVP5147_CH1,
-		.input_route = INPUT_SVIDEO_VI2C_VI1C,
-		.output_route = OUTPUT_10BIT_422_EMBEDDED_SYNC,
-	},
-};
-
-static struct vpif_capture_config dm646x_vpif_capture_cfg = {
-	.setup_input_path = setup_vpif_input_path,
-	.setup_input_channel_mode = setup_vpif_input_channel_mode,
-	.subdev_info = vpif_capture_sdev_info,
-	.subdev_count = ARRAY_SIZE(vpif_capture_sdev_info),
-	.i2c_adapter_id = 1,
-	.chan_config[0] = {
-		.inputs = dm6467_ch0_inputs,
-		.input_count = ARRAY_SIZE(dm6467_ch0_inputs),
-		.vpif_if = {
-			.if_type = VPIF_IF_BT656,
-			.hd_pol = 1,
-			.vd_pol = 1,
-			.fid_pol = 0,
-		},
-	},
-	.chan_config[1] = {
-		.inputs = dm6467_ch1_inputs,
-		.input_count = ARRAY_SIZE(dm6467_ch1_inputs),
-		.vpif_if = {
-			.if_type = VPIF_IF_BT656,
-			.hd_pol = 1,
-			.vd_pol = 1,
-			.fid_pol = 0,
-		},
-	},
-	.card_name = "DM646x EVM Video Capture",
-};
-
-static void __init evm_init_video(void)
-{
-	spin_lock_init(&vpif_reg_lock);
-
-	dm646x_setup_vpif(&dm646x_vpif_display_config,
-			  &dm646x_vpif_capture_cfg);
-}
-
-static void __init evm_init_i2c(void)
-{
-	davinci_init_i2c(&i2c_pdata);
-	i2c_add_driver(&dm6467evm_cpld_driver);
-	i2c_register_board_info(1, i2c_info, ARRAY_SIZE(i2c_info));
-	evm_init_cpld();
-	evm_init_video();
-}
-#endif
-
-#define DM646X_REF_FREQ			27000000
-#define DM646X_AUX_FREQ			24000000
-#define DM6467T_EVM_REF_FREQ		33000000
-
-static void __init davinci_map_io(void)
-{
-	dm646x_init();
-}
-
-static void __init dm646x_evm_init_time(void)
-{
-	dm646x_init_time(DM646X_REF_FREQ, DM646X_AUX_FREQ);
-}
-
-static void __init dm6467t_evm_init_time(void)
-{
-	dm646x_init_time(DM6467T_EVM_REF_FREQ, DM646X_AUX_FREQ);
-}
-
-#define DM646X_EVM_PHY_ID		"davinci_mdio-0:01"
-/*
- * The following EDMA channels/slots are not being used by drivers (for
- * example: Timer, GPIO, UART events etc) on dm646x, hence they are being
- * reserved for codecs on the DSP side.
- */
-static const s16 dm646x_dma_rsv_chans[][2] = {
-	/* (offset, number) */
-	{ 0,  4},
-	{13,  3},
-	{24,  4},
-	{30,  2},
-	{54,  3},
-	{-1, -1}
-};
-
-static const s16 dm646x_dma_rsv_slots[][2] = {
-	/* (offset, number) */
-	{ 0,  4},
-	{13,  3},
-	{24,  4},
-	{30,  2},
-	{54,  3},
-	{128, 384},
-	{-1, -1}
-};
-
-static struct edma_rsv_info dm646x_edma_rsv[] = {
-	{
-		.rsv_chans	= dm646x_dma_rsv_chans,
-		.rsv_slots	= dm646x_dma_rsv_slots,
-	},
-};
-
-static __init void evm_init(void)
-{
-	int ret;
-	struct davinci_soc_info *soc_info = &davinci_soc_info;
-
-	dm646x_register_clocks();
-
-	ret = dm646x_gpio_register();
-	if (ret)
-		pr_warn("%s: GPIO init failed: %d\n", __func__, ret);
-
-#ifdef CONFIG_I2C
-	nvmem_add_cell_table(&dm646x_evm_nvmem_cell_table);
-	nvmem_add_cell_lookups(&dm646x_evm_nvmem_cell_lookup, 1);
-	evm_init_i2c();
-#endif
-
-	davinci_serial_init(dm646x_serial_device);
-	dm646x_init_mcasp0(&dm646x_evm_snd_data[0]);
-	dm646x_init_mcasp1(&dm646x_evm_snd_data[1]);
-
-	if (machine_is_davinci_dm6467tevm())
-		davinci_nand_data.timing = &dm6467tevm_nandflash_timing;
-
-	if (platform_device_register(&davinci_aemif_device))
-		pr_warn("%s: Cannot register AEMIF device.\n", __func__);
-
-	dm646x_init_edma(dm646x_edma_rsv);
-
-	if (HAS_ATA)
-		davinci_init_ide();
-
-	soc_info->emac_pdata->phy_id = DM646X_EVM_PHY_ID;
-}
-
-MACHINE_START(DAVINCI_DM6467_EVM, "DaVinci DM646x EVM")
-	.atag_offset  = 0x100,
-	.map_io       = davinci_map_io,
-	.init_irq     = dm646x_init_irq,
-	.init_time	= dm646x_evm_init_time,
-	.init_machine = evm_init,
-	.init_late	= davinci_init_late,
-	.dma_zone_size	= SZ_128M,
-MACHINE_END
-
-MACHINE_START(DAVINCI_DM6467TEVM, "DaVinci DM6467T EVM")
-	.atag_offset  = 0x100,
-	.map_io       = davinci_map_io,
-	.init_irq     = dm646x_init_irq,
-	.init_time	= dm6467t_evm_init_time,
-	.init_machine = evm_init,
-	.init_late	= davinci_init_late,
-	.dma_zone_size	= SZ_128M,
-MACHINE_END
-
diff --git a/arch/arm/mach-davinci/board-mityomapl138.c b/arch/arm/mach-davinci/board-mityomapl138.c
index 2127969beb96..a46e7b9ff8e0 100644
--- a/arch/arm/mach-davinci/board-mityomapl138.c
+++ b/arch/arm/mach-davinci/board-mityomapl138.c
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Critical Link MityOMAP-L138 SoM
  *
  * Copyright (C) 2010 Critical Link LLC - https://www.criticallink.com
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2. This program is licensed "as is" without any warranty of
- * any kind, whether express or implied.
  */
 
 #define pr_fmt(fmt) "MityOMAPL138: " fmt
@@ -28,12 +25,14 @@
 #include <asm/io.h>
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
-#include <mach/common.h>
-#include <mach/da8xx.h>
+
+#include "common.h"
+#include "da8xx.h"
+#include "mux.h"
+
 #include <linux/platform_data/mtd-davinci.h>
 #include <linux/platform_data/mtd-davinci-aemif.h>
 #include <linux/platform_data/ti-aemif.h>
-#include <mach/mux.h>
 #include <linux/platform_data/spi-davinci.h>
 
 #define MITYOMAPL138_PHY_ID		""
diff --git a/arch/arm/mach-davinci/board-neuros-osd2.c b/arch/arm/mach-davinci/board-neuros-osd2.c
deleted file mode 100644
index b4843f68bb57..000000000000
--- a/arch/arm/mach-davinci/board-neuros-osd2.c
+++ /dev/null
@@ -1,239 +0,0 @@
-/*
- * Neuros Technologies OSD2 board support
- *
- * Modified from original 644X-EVM board support.
- * 2008 (c) Neuros Technology, LLC.
- * 2009 (c) Jorge Luis Zapata Muga <jorgeluis.zapata@gmail.com>
- * 2009 (c) Andrey A. Porodko <Andrey.Porodko@gmail.com>
- *
- * The Neuros OSD 2.0 is the hardware component of the Neuros Open
- * Internet Television Platform. Hardware is very close to TI
- * DM644X-EVM board. It has:
- * 	DM6446M02 module with 256MB NAND, 256MB RAM, TLV320AIC32 AIC,
- * 	USB, Ethernet, SD/MMC, UART, THS8200, TVP7000 for video.
- * 	Additionally realtime clock, IR remote control receiver,
- * 	IR Blaster based on MSP430 (firmware although is different
- * 	from used in DM644X-EVM), internal ATA-6 3.5” HDD drive
- * 	with PATA interface, two muxed red-green leds.
- *
- * For more information please refer to
- * 		http://wiki.neurostechnology.com/index.php/OSD_2.0_HD
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-#include <linux/platform_device.h>
-#include <linux/gpio.h>
-#include <linux/leds.h>
-#include <linux/mtd/partitions.h>
-#include <linux/platform_data/gpio-davinci.h>
-#include <linux/platform_data/i2c-davinci.h>
-#include <linux/platform_data/mmc-davinci.h>
-#include <linux/platform_data/mtd-davinci.h>
-#include <linux/platform_data/usb-davinci.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-
-#include <mach/common.h>
-#include <mach/serial.h>
-#include <mach/mux.h>
-
-#include "davinci.h"
-
-#define NEUROS_OSD2_PHY_ID		"davinci_mdio-0:01"
-#define LXT971_PHY_ID			0x001378e2
-#define LXT971_PHY_MASK			0xfffffff0
-
-#define	NTOSD2_AUDIOSOC_I2C_ADDR	0x18
-#define	NTOSD2_MSP430_I2C_ADDR		0x59
-#define	NTOSD2_MSP430_IRQ		2
-
-/* Neuros OSD2 has a Samsung 256 MByte NAND flash (Dev ID of 0xAA,
- * 2048 blocks in the device, 64 pages per block, 2048 bytes per
- * page.
- */
-
-#define NAND_BLOCK_SIZE		SZ_128K
-
-static struct mtd_partition davinci_ntosd2_nandflash_partition[] = {
-	{
-		/* UBL (a few copies) plus U-Boot */
-		.name		= "bootloader",
-		.offset		= 0,
-		.size		= 15 * NAND_BLOCK_SIZE,
-		.mask_flags	= MTD_WRITEABLE, /* force read-only */
-	}, {
-		/* U-Boot environment */
-		.name		= "params",
-		.offset		= MTDPART_OFS_APPEND,
-		.size		= 1 * NAND_BLOCK_SIZE,
-		.mask_flags	= 0,
-	}, {
-		/* Kernel */
-		.name		= "kernel",
-		.offset		= MTDPART_OFS_APPEND,
-		.size		= SZ_4M,
-		.mask_flags	= 0,
-	}, {
-		/* File System */
-		.name		= "filesystem",
-		.offset		= MTDPART_OFS_APPEND,
-		.size		= MTDPART_SIZ_FULL,
-		.mask_flags	= 0,
-	}
-	/* A few blocks at end hold a flash Bad Block Table. */
-};
-
-static struct davinci_nand_pdata davinci_ntosd2_nandflash_data = {
-	.core_chipsel	= 0,
-	.parts		= davinci_ntosd2_nandflash_partition,
-	.nr_parts	= ARRAY_SIZE(davinci_ntosd2_nandflash_partition),
-	.engine_type	= NAND_ECC_ENGINE_TYPE_ON_HOST,
-	.ecc_bits	= 1,
-	.bbt_options	= NAND_BBT_USE_FLASH,
-};
-
-static struct resource davinci_ntosd2_nandflash_resource[] = {
-	{
-		.start		= DM644X_ASYNC_EMIF_DATA_CE0_BASE,
-		.end		= DM644X_ASYNC_EMIF_DATA_CE0_BASE + SZ_16M - 1,
-		.flags		= IORESOURCE_MEM,
-	}, {
-		.start		= DM644X_ASYNC_EMIF_CONTROL_BASE,
-		.end		= DM644X_ASYNC_EMIF_CONTROL_BASE + SZ_4K - 1,
-		.flags		= IORESOURCE_MEM,
-	},
-};
-
-static struct platform_device davinci_ntosd2_nandflash_device = {
-	.name		= "davinci_nand",
-	.id		= 0,
-	.dev		= {
-		.platform_data	= &davinci_ntosd2_nandflash_data,
-	},
-	.num_resources	= ARRAY_SIZE(davinci_ntosd2_nandflash_resource),
-	.resource	= davinci_ntosd2_nandflash_resource,
-};
-
-static u64 davinci_fb_dma_mask = DMA_BIT_MASK(32);
-
-static struct platform_device davinci_fb_device = {
-	.name		= "davincifb",
-	.id		= -1,
-	.dev = {
-		.dma_mask		= &davinci_fb_dma_mask,
-		.coherent_dma_mask	= DMA_BIT_MASK(32),
-	},
-	.num_resources = 0,
-};
-
-static const struct gpio_led ntosd2_leds[] = {
-	{ .name = "led1_green", .gpio = 10, },
-	{ .name = "led1_red",   .gpio = 11, },
-	{ .name = "led2_green", .gpio = 12, },
-	{ .name = "led2_red",   .gpio = 13, },
-};
-
-static struct gpio_led_platform_data ntosd2_leds_data = {
-	.num_leds	= ARRAY_SIZE(ntosd2_leds),
-	.leds		= ntosd2_leds,
-};
-
-static struct platform_device ntosd2_leds_dev = {
-	.name = "leds-gpio",
-	.id   = -1,
-	.dev = {
-		.platform_data 		= &ntosd2_leds_data,
-	},
-};
-
-
-static struct platform_device *davinci_ntosd2_devices[] __initdata = {
-	&davinci_fb_device,
-	&ntosd2_leds_dev,
-};
-
-static void __init davinci_ntosd2_map_io(void)
-{
-	dm644x_init();
-}
-
-static struct davinci_mmc_config davinci_ntosd2_mmc_config = {
-	.wires		= 4,
-};
-
-#define HAS_ATA		(IS_ENABLED(CONFIG_BLK_DEV_PALMCHIP_BK3710) || \
-			 IS_ENABLED(CONFIG_PATA_BK3710))
-
-#define HAS_NAND	IS_ENABLED(CONFIG_MTD_NAND_DAVINCI)
-
-static __init void davinci_ntosd2_init(void)
-{
-	int ret;
-	struct clk *aemif_clk;
-	struct davinci_soc_info *soc_info = &davinci_soc_info;
-
-	dm644x_register_clocks();
-
-	dm644x_init_devices();
-
-	ret = dm644x_gpio_register();
-	if (ret)
-		pr_warn("%s: GPIO init failed: %d\n", __func__, ret);
-
-	aemif_clk = clk_get(NULL, "aemif");
-	clk_prepare_enable(aemif_clk);
-
-	if (HAS_ATA) {
-		if (HAS_NAND)
-			pr_warn("WARNING: both IDE and Flash are enabled, but they share AEMIF pins\n"
-				"\tDisable IDE for NAND/NOR support\n");
-		davinci_init_ide();
-	} else if (HAS_NAND) {
-		davinci_cfg_reg(DM644X_HPIEN_DISABLE);
-		davinci_cfg_reg(DM644X_ATAEN_DISABLE);
-
-		/* only one device will be jumpered and detected */
-		if (HAS_NAND)
-			platform_device_register(
-					&davinci_ntosd2_nandflash_device);
-	}
-
-	platform_add_devices(davinci_ntosd2_devices,
-				ARRAY_SIZE(davinci_ntosd2_devices));
-
-	davinci_serial_init(dm644x_serial_device);
-	dm644x_init_asp();
-
-	soc_info->emac_pdata->phy_id = NEUROS_OSD2_PHY_ID;
-
-	davinci_setup_usb(1000, 8);
-	/*
-	 * Mux the pins to be GPIOs, VLYNQEN is already done at startup.
-	 * The AEAWx are five new AEAW pins that can be muxed by separately.
-	 * They are a bitmask for GPIO management. According TI
-	 * documentation (https://www.ti.com/lit/gpn/tms320dm6446) to employ
-	 * gpio(10,11,12,13) for leds any combination of bits works except
-	 * four last. So we are to reset all five.
-	 */
-	davinci_cfg_reg(DM644X_AEAW0);
-	davinci_cfg_reg(DM644X_AEAW1);
-	davinci_cfg_reg(DM644X_AEAW2);
-	davinci_cfg_reg(DM644X_AEAW3);
-	davinci_cfg_reg(DM644X_AEAW4);
-
-	davinci_setup_mmc(0, &davinci_ntosd2_mmc_config);
-}
-
-MACHINE_START(NEUROS_OSD2, "Neuros OSD2")
-	/* Maintainer: Neuros Technologies <neuros@groups.google.com> */
-	.atag_offset	= 0x100,
-	.map_io		 = davinci_ntosd2_map_io,
-	.init_irq	= dm644x_init_irq,
-	.init_time	= dm644x_init_time,
-	.init_machine = davinci_ntosd2_init,
-	.init_late	= davinci_init_late,
-	.dma_zone_size	= SZ_128M,
-MACHINE_END
diff --git a/arch/arm/mach-davinci/board-omapl138-hawk.c b/arch/arm/mach-davinci/board-omapl138-hawk.c
index 88df8011a4e6..8a80115999ad 100644
--- a/arch/arm/mach-davinci/board-omapl138-hawk.c
+++ b/arch/arm/mach-davinci/board-omapl138-hawk.c
@@ -1,13 +1,10 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Hawkboard.org based on TI's OMAP-L138 Platform
  *
  * Initial code: Syed Mohammed Khasim
  *
  * Copyright (C) 2009 Texas Instruments Incorporated - https://www.ti.com
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2. This program is licensed "as is" without any warranty of
- * any kind, whether express or implied.
  */
 #include <linux/kernel.h>
 #include <linux/init.h>
@@ -27,9 +24,9 @@
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
 
-#include <mach/common.h>
-#include <mach/da8xx.h>
-#include <mach/mux.h>
+#include "common.h"
+#include "da8xx.h"
+#include "mux.h"
 
 #define HAWKBOARD_PHY_ID		"davinci_mdio-0:07"
 
diff --git a/arch/arm/mach-davinci/board-sffsdr.c b/arch/arm/mach-davinci/board-sffsdr.c
deleted file mode 100644
index 6930b2f485d1..000000000000
--- a/arch/arm/mach-davinci/board-sffsdr.c
+++ /dev/null
@@ -1,151 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later
-/*
- * Lyrtech SFFSDR board support.
- *
- * Copyright (C) 2008 Philip Balister, OpenSDR <philip@opensdr.com>
- * Copyright (C) 2008 Lyrtech <www.lyrtech.com>
- *
- * Based on DV-EVM platform, original copyright follows:
- *
- * Copyright (C) 2007 MontaVista Software, Inc.
- */
-
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/i2c.h>
-#include <linux/property.h>
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/rawnand.h>
-#include <linux/mtd/partitions.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/flash.h>
-
-#include <mach/common.h>
-#include <linux/platform_data/i2c-davinci.h>
-#include <mach/serial.h>
-#include <mach/mux.h>
-#include <linux/platform_data/usb-davinci.h>
-
-#include "davinci.h"
-
-#define SFFSDR_PHY_ID		"davinci_mdio-0:01"
-static struct mtd_partition davinci_sffsdr_nandflash_partition[] = {
-	/* U-Boot Environment: Block 0
-	 * UBL:                Block 1
-	 * U-Boot:             Blocks 6-7 (256 kb)
-	 * Integrity Kernel:   Blocks 8-31 (3 Mb)
-	 * Integrity Data:     Blocks 100-END
-	 */
-	{
-		.name		= "Linux Kernel",
-		.offset		= 32 * SZ_128K,
-		.size		= 16 * SZ_128K, /* 2 Mb */
-		.mask_flags	= MTD_WRITEABLE, /* Force read-only */
-	},
-	{
-		.name		= "Linux ROOT",
-		.offset		= MTDPART_OFS_APPEND,
-		.size		= 256 * SZ_128K, /* 32 Mb */
-		.mask_flags	= 0, /* R/W */
-	},
-};
-
-static struct flash_platform_data davinci_sffsdr_nandflash_data = {
-	.parts		= davinci_sffsdr_nandflash_partition,
-	.nr_parts	= ARRAY_SIZE(davinci_sffsdr_nandflash_partition),
-};
-
-static struct resource davinci_sffsdr_nandflash_resource[] = {
-	{
-		.start		= DM644X_ASYNC_EMIF_DATA_CE0_BASE,
-		.end		= DM644X_ASYNC_EMIF_DATA_CE0_BASE + SZ_16M - 1,
-		.flags		= IORESOURCE_MEM,
-	}, {
-		.start		= DM644X_ASYNC_EMIF_CONTROL_BASE,
-		.end		= DM644X_ASYNC_EMIF_CONTROL_BASE + SZ_4K - 1,
-		.flags		= IORESOURCE_MEM,
-	},
-};
-
-static struct platform_device davinci_sffsdr_nandflash_device = {
-	.name		= "davinci_nand", /* Name of driver */
-	.id		= 0,
-	.dev		= {
-		.platform_data	= &davinci_sffsdr_nandflash_data,
-	},
-	.num_resources	= ARRAY_SIZE(davinci_sffsdr_nandflash_resource),
-	.resource	= davinci_sffsdr_nandflash_resource,
-};
-
-static const struct property_entry eeprom_properties[] = {
-	PROPERTY_ENTRY_U32("pagesize", 32),
-	{ }
-};
-
-static const struct software_node eeprom_node = {
-	.properties = eeprom_properties,
-};
-
-static struct i2c_board_info __initdata i2c_info[] =  {
-	{
-		I2C_BOARD_INFO("24c64", 0x50),
-		.swnode = &eeprom_node,
-	},
-	/* Other I2C devices:
-	 * MSP430,  addr 0x23 (not used)
-	 * PCA9543, addr 0x70 (setup done by U-Boot)
-	 * ADS7828, addr 0x48 (ADC for voltage monitoring.)
-	 */
-};
-
-static struct davinci_i2c_platform_data i2c_pdata = {
-	.bus_freq	= 20 /* kHz */,
-	.bus_delay	= 100 /* usec */,
-};
-
-static void __init sffsdr_init_i2c(void)
-{
-	davinci_init_i2c(&i2c_pdata);
-	i2c_register_board_info(1, i2c_info, ARRAY_SIZE(i2c_info));
-}
-
-static struct platform_device *davinci_sffsdr_devices[] __initdata = {
-	&davinci_sffsdr_nandflash_device,
-};
-
-static void __init davinci_sffsdr_map_io(void)
-{
-	dm644x_init();
-}
-
-static __init void davinci_sffsdr_init(void)
-{
-	struct davinci_soc_info *soc_info = &davinci_soc_info;
-
-	dm644x_register_clocks();
-
-	dm644x_init_devices();
-
-	platform_add_devices(davinci_sffsdr_devices,
-			     ARRAY_SIZE(davinci_sffsdr_devices));
-	sffsdr_init_i2c();
-	davinci_serial_init(dm644x_serial_device);
-	soc_info->emac_pdata->phy_id = SFFSDR_PHY_ID;
-	davinci_setup_usb(0, 0); /* We support only peripheral mode. */
-
-	/* mux VLYNQ pins */
-	davinci_cfg_reg(DM644X_VLYNQEN);
-	davinci_cfg_reg(DM644X_VLYNQWD);
-}
-
-MACHINE_START(SFFSDR, "Lyrtech SFFSDR")
-	.atag_offset  = 0x100,
-	.map_io	      = davinci_sffsdr_map_io,
-	.init_irq     = dm644x_init_irq,
-	.init_time	= dm644x_init_time,
-	.init_machine = davinci_sffsdr_init,
-	.init_late	= davinci_init_late,
-	.dma_zone_size	= SZ_128M,
-MACHINE_END
diff --git a/arch/arm/mach-davinci/common.c b/arch/arm/mach-davinci/common.c
index ae61d19f9b3a..c1ce6b2a8d48 100644
--- a/arch/arm/mach-davinci/common.c
+++ b/arch/arm/mach-davinci/common.c
@@ -1,12 +1,10 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Code commons to all DaVinci SoCs.
  *
  * Author: Mark A. Greer <mgreer@mvista.com>
  *
- * 2009 (c) MontaVista Software, Inc. This file is licensed under
- * the terms of the GNU General Public License version 2. This program
- * is licensed "as is" without any warranty of any kind, whether express
- * or implied.
+ * 2009 (c) MontaVista Software, Inc.
  */
 #include <linux/module.h>
 #include <linux/io.h>
@@ -17,8 +15,8 @@
 #include <asm/tlb.h>
 #include <asm/mach/map.h>
 
-#include <mach/common.h>
-#include <mach/cputype.h>
+#include "common.h"
+#include "cputype.h"
 
 struct davinci_soc_info davinci_soc_info;
 EXPORT_SYMBOL(davinci_soc_info);
diff --git a/arch/arm/mach-davinci/common.h b/arch/arm/mach-davinci/common.h
new file mode 100644
index 000000000000..772b51e0ac5e
--- /dev/null
+++ b/arch/arm/mach-davinci/common.h
@@ -0,0 +1,77 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Header for code common to all DaVinci machines.
+ *
+ * Author: Kevin Hilman, MontaVista Software, Inc. <source@mvista.com>
+ *
+ * 2007 (c) MontaVista Software, Inc.
+ */
+
+#ifndef __ARCH_ARM_MACH_DAVINCI_COMMON_H
+#define __ARCH_ARM_MACH_DAVINCI_COMMON_H
+
+#include <linux/clk.h>
+#include <linux/compiler.h>
+#include <linux/types.h>
+#include <linux/reboot.h>
+
+#include <asm/irq.h>
+
+#define DAVINCI_INTC_START		NR_IRQS
+#define DAVINCI_INTC_IRQ(_irqnum)	(DAVINCI_INTC_START + (_irqnum))
+
+struct davinci_gpio_controller;
+
+/*
+ * SoC info passed into common davinci modules.
+ *
+ * Base addresses in this structure should be physical and not virtual.
+ * Modules that take such base addresses, should internally ioremap() them to
+ * use.
+ */
+struct davinci_soc_info {
+	struct map_desc			*io_desc;
+	unsigned long			io_desc_num;
+	u32				cpu_id;
+	u32				jtag_id;
+	u32				jtag_id_reg;
+	struct davinci_id		*ids;
+	unsigned long			ids_num;
+	u32				pinmux_base;
+	const struct mux_config		*pinmux_pins;
+	unsigned long			pinmux_pins_num;
+	int				gpio_type;
+	u32				gpio_base;
+	unsigned			gpio_num;
+	unsigned			gpio_irq;
+	unsigned			gpio_unbanked;
+	struct davinci_gpio_controller	*gpio_ctlrs;
+	int				gpio_ctlrs_num;
+	struct emac_platform_data	*emac_pdata;
+	dma_addr_t			sram_dma;
+	unsigned			sram_len;
+};
+
+extern struct davinci_soc_info davinci_soc_info;
+
+extern void davinci_common_init(const struct davinci_soc_info *soc_info);
+extern void davinci_init_ide(void);
+void davinci_init_late(void);
+
+#ifdef CONFIG_CPU_FREQ
+int davinci_cpufreq_init(void);
+#else
+static inline int davinci_cpufreq_init(void) { return 0; }
+#endif
+
+#ifdef CONFIG_SUSPEND
+int davinci_pm_init(void);
+#else
+static inline int davinci_pm_init(void) { return 0; }
+#endif
+
+void __init pdata_quirks_init(void);
+
+#define SRAM_SIZE	SZ_128K
+
+#endif /* __ARCH_ARM_MACH_DAVINCI_COMMON_H */
diff --git a/arch/arm/mach-davinci/cpuidle.h b/arch/arm/mach-davinci/cpuidle.h
index 0d9193aefab5..976d43073597 100644
--- a/arch/arm/mach-davinci/cpuidle.h
+++ b/arch/arm/mach-davinci/cpuidle.h
@@ -1,11 +1,8 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * TI DaVinci cpuidle platform support
  *
  * 2009 (C) Texas Instruments, Inc. https://www.ti.com/
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2. This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
  */
 #ifndef _MACH_DAVINCI_CPUIDLE_H
 #define _MACH_DAVINCI_CPUIDLE_H
diff --git a/arch/arm/mach-davinci/cputype.h b/arch/arm/mach-davinci/cputype.h
new file mode 100644
index 000000000000..4590afdbe449
--- /dev/null
+++ b/arch/arm/mach-davinci/cputype.h
@@ -0,0 +1,84 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * DaVinci CPU type detection
+ *
+ * Author: Kevin Hilman, Deep Root Systems, LLC
+ *
+ * Defines the cpu_is_*() macros for runtime detection of DaVinci
+ * device type.  In addition, if support for a given device is not
+ * compiled in to the kernel, the macros return 0 so that
+ * resulting code can be optimized out.
+ *
+ * 2009 (c) Deep Root Systems, LLC.
+ */
+#ifndef _ASM_ARCH_CPU_H
+#define _ASM_ARCH_CPU_H
+
+#include "common.h"
+
+struct davinci_id {
+	u8	variant;	/* JTAG ID bits 31:28 */
+	u16	part_no;	/* JTAG ID bits 27:12 */
+	u16	manufacturer;	/* JTAG ID bits 11:1 */
+	u32	cpu_id;
+	char	*name;
+};
+
+/* Can use lower 16 bits of cpu id  for a variant when required */
+#define	DAVINCI_CPU_ID_DM6446		0x64460000
+#define	DAVINCI_CPU_ID_DM6467		0x64670000
+#define	DAVINCI_CPU_ID_DM355		0x03550000
+#define	DAVINCI_CPU_ID_DM365		0x03650000
+#define	DAVINCI_CPU_ID_DA830		0x08300000
+#define	DAVINCI_CPU_ID_DA850		0x08500000
+
+#define IS_DAVINCI_CPU(type, id)					\
+static inline int is_davinci_ ##type(void)				\
+{									\
+	return (davinci_soc_info.cpu_id == (id));			\
+}
+
+IS_DAVINCI_CPU(dm644x, DAVINCI_CPU_ID_DM6446)
+IS_DAVINCI_CPU(dm646x, DAVINCI_CPU_ID_DM6467)
+IS_DAVINCI_CPU(dm355, DAVINCI_CPU_ID_DM355)
+IS_DAVINCI_CPU(dm365, DAVINCI_CPU_ID_DM365)
+IS_DAVINCI_CPU(da830, DAVINCI_CPU_ID_DA830)
+IS_DAVINCI_CPU(da850, DAVINCI_CPU_ID_DA850)
+
+#ifdef CONFIG_ARCH_DAVINCI_DM644x
+#define cpu_is_davinci_dm644x() is_davinci_dm644x()
+#else
+#define cpu_is_davinci_dm644x() 0
+#endif
+
+#ifdef CONFIG_ARCH_DAVINCI_DM646x
+#define cpu_is_davinci_dm646x() is_davinci_dm646x()
+#else
+#define cpu_is_davinci_dm646x() 0
+#endif
+
+#ifdef CONFIG_ARCH_DAVINCI_DM355
+#define cpu_is_davinci_dm355() is_davinci_dm355()
+#else
+#define cpu_is_davinci_dm355() 0
+#endif
+
+#ifdef CONFIG_ARCH_DAVINCI_DM365
+#define cpu_is_davinci_dm365() is_davinci_dm365()
+#else
+#define cpu_is_davinci_dm365() 0
+#endif
+
+#ifdef CONFIG_ARCH_DAVINCI_DA830
+#define cpu_is_davinci_da830() is_davinci_da830()
+#else
+#define cpu_is_davinci_da830() 0
+#endif
+
+#ifdef CONFIG_ARCH_DAVINCI_DA850
+#define cpu_is_davinci_da850() is_davinci_da850()
+#else
+#define cpu_is_davinci_da850() 0
+#endif
+
+#endif
diff --git a/arch/arm/mach-davinci/da830.c b/arch/arm/mach-davinci/da830.c
index 018ab4b549f1..eab5fac18806 100644
--- a/arch/arm/mach-davinci/da830.c
+++ b/arch/arm/mach-davinci/da830.c
@@ -1,12 +1,10 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * TI DA830/OMAP L137 chip specific setup
  *
  * Author: Mark A. Greer <mgreer@mvista.com>
  *
- * 2009 (c) MontaVista Software, Inc. This file is licensed under
- * the terms of the GNU General Public License version 2. This program
- * is licensed "as is" without any warranty of any kind, whether express
- * or implied.
+ * 2009 (c) MontaVista Software, Inc.
  */
 #include <linux/clk-provider.h>
 #include <linux/clk/davinci.h>
@@ -16,14 +14,13 @@
 #include <linux/irqchip/irq-davinci-cp-intc.h>
 #include <linux/platform_data/gpio-davinci.h>
 
-#include <asm/mach/map.h>
-
-#include <mach/common.h>
-#include <mach/cputype.h>
-#include <mach/da8xx.h>
-
 #include <clocksource/timer-davinci.h>
 
+#include <asm/mach/map.h>
+
+#include "common.h"
+#include "cputype.h"
+#include "da8xx.h"
 #include "irqs.h"
 #include "mux.h"
 
diff --git a/arch/arm/mach-davinci/da850.c b/arch/arm/mach-davinci/da850.c
index 68156e7239a6..635e88daf5dd 100644
--- a/arch/arm/mach-davinci/da850.c
+++ b/arch/arm/mach-davinci/da850.c
@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * TI DA850/OMAP-L138 chip specific setup
  *
@@ -6,10 +7,7 @@
  * Derived from: arch/arm/mach-davinci/da830.c
  * Original Copyrights follow:
  *
- * 2009 (c) MontaVista Software, Inc. This file is licensed under
- * the terms of the GNU General Public License version 2. This program
- * is licensed "as is" without any warranty of any kind, whether express
- * or implied.
+ * 2009 (c) MontaVista Software, Inc.
  */
 
 #include <linux/clk-provider.h>
@@ -28,16 +26,14 @@
 #include <linux/platform_device.h>
 #include <linux/regmap.h>
 #include <linux/regulator/consumer.h>
+#include <clocksource/timer-davinci.h>
 
 #include <asm/mach/map.h>
 
-#include <mach/common.h>
-#include <mach/cputype.h>
-#include <mach/da8xx.h>
-#include <mach/pm.h>
-
-#include <clocksource/timer-davinci.h>
-
+#include "common.h"
+#include "cputype.h"
+#include "da8xx.h"
+#include "pm.h"
 #include "irqs.h"
 #include "mux.h"
 
diff --git a/arch/arm/mach-davinci/da8xx-dt.c b/arch/arm/mach-davinci/da8xx-dt.c
index 0cd2f30aeb9c..45763a9b37ee 100644
--- a/arch/arm/mach-davinci/da8xx-dt.c
+++ b/arch/arm/mach-davinci/da8xx-dt.c
@@ -7,8 +7,8 @@
 
 #include <asm/mach/arch.h>
 
-#include <mach/common.h>
-#include <mach/da8xx.h>
+#include "common.h"
+#include "da8xx.h"
 
 #ifdef CONFIG_ARCH_DAVINCI_DA850
 
diff --git a/arch/arm/mach-davinci/include/mach/da8xx.h b/arch/arm/mach-davinci/da8xx.h
index 1618b30661a9..382811dbbc3b 100644
--- a/arch/arm/mach-davinci/include/mach/da8xx.h
+++ b/arch/arm/mach-davinci/da8xx.h
@@ -1,12 +1,10 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * Chip specific defines for DA8XX/OMAP L1XX SoC
  *
  * Author: Mark A. Greer <mgreer@mvista.com>
  *
- * 2007, 2009-2010 (c) MontaVista Software, Inc. This file is licensed under
- * the terms of the GNU General Public License version 2. This program
- * is licensed "as is" without any warranty of any kind, whether express
- * or implied.
+ * 2007, 2009-2010 (c) MontaVista Software, Inc.
  */
 #ifndef __ASM_ARCH_DAVINCI_DA8XX_H
 #define __ASM_ARCH_DAVINCI_DA8XX_H
@@ -21,8 +19,9 @@
 #include <linux/regmap.h>
 #include <linux/videodev2.h>
 
-#include <mach/serial.h>
-#include <mach/pm.h>
+#include "serial.h"
+#include "pm.h"
+
 #include <linux/platform_data/edma.h>
 #include <linux/platform_data/i2c-davinci.h>
 #include <linux/platform_data/mmc-davinci.h>
diff --git a/arch/arm/mach-davinci/davinci.h b/arch/arm/mach-davinci/davinci.h
index 208d7a4d3597..b7172797692b 100644
--- a/arch/arm/mach-davinci/davinci.h
+++ b/arch/arm/mach-davinci/davinci.h
@@ -1,18 +1,10 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * This file contains the processor specific definitions
  * of the TI DM644x, DM355, DM365, and DM646x.
  *
  * Copyright (C) 2011 Texas Instruments Incorporated
  * Copyright (c) 2007 Deep Root Systems, LLC
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation version 2.
- *
- * This program is distributed "as is" WITHOUT ANY WARRANTY of any
- * kind, whether express or implied; without even the implied warranty
- * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
  */
 #ifndef __DAVINCI_H
 #define __DAVINCI_H
@@ -25,7 +17,8 @@
 #include <linux/platform_data/davinci_asp.h>
 #include <linux/platform_data/edma.h>
 #include <linux/platform_data/keyscan-davinci.h>
-#include <mach/hardware.h>
+
+#include "hardware.h"
 
 #include <media/davinci/vpfe_capture.h>
 #include <media/davinci/vpif_types.h>
diff --git a/arch/arm/mach-davinci/devices-da8xx.c b/arch/arm/mach-davinci/devices-da8xx.c
index bb368938fc49..ef9593558e5f 100644
--- a/arch/arm/mach-davinci/devices-da8xx.c
+++ b/arch/arm/mach-davinci/devices-da8xx.c
@@ -18,10 +18,9 @@
 #include <linux/reboot.h>
 #include <linux/serial_8250.h>
 
-#include <mach/common.h>
-#include <mach/cputype.h>
-#include <mach/da8xx.h>
-
+#include "common.h"
+#include "cputype.h"
+#include "da8xx.h"
 #include "asp.h"
 #include "cpuidle.h"
 #include "irqs.h"
diff --git a/arch/arm/mach-davinci/devices.c b/arch/arm/mach-davinci/devices.c
index 849e811fade7..199c26d9a2b6 100644
--- a/arch/arm/mach-davinci/devices.c
+++ b/arch/arm/mach-davinci/devices.c
@@ -14,10 +14,9 @@
 #include <linux/io.h>
 #include <linux/reboot.h>
 
-#include <mach/hardware.h>
-#include <mach/cputype.h>
-#include <mach/mux.h>
-
+#include "hardware.h"
+#include "cputype.h"
+#include "mux.h"
 #include "davinci.h"
 #include "irqs.h"
 
diff --git a/arch/arm/mach-davinci/dm355.c b/arch/arm/mach-davinci/dm355.c
index 5de72d2fa8f0..a12ba859beca 100644
--- a/arch/arm/mach-davinci/dm355.c
+++ b/arch/arm/mach-davinci/dm355.c
@@ -1,12 +1,10 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * TI DaVinci DM355 chip specific setup
  *
  * Author: Kevin Hilman, Deep Root Systems, LLC
  *
- * 2007 (c) Deep Root Systems, LLC. This file is licensed under
- * the terms of the GNU General Public License version 2. This program
- * is licensed "as is" without any warranty of any kind, whether express
- * or implied.
+ * 2007 (c) Deep Root Systems, LLC.
  */
 
 #include <linux/clk-provider.h>
@@ -24,15 +22,13 @@
 #include <linux/serial_8250.h>
 #include <linux/spi/spi.h>
 
-#include <asm/mach/map.h>
-
-#include <mach/common.h>
-#include <mach/cputype.h>
-#include <mach/mux.h>
-#include <mach/serial.h>
-
 #include <clocksource/timer-davinci.h>
 
+#include <asm/mach/map.h>
+
+#include "common.h"
+#include "cputype.h"
+#include "serial.h"
 #include "asp.h"
 #include "davinci.h"
 #include "irqs.h"
diff --git a/arch/arm/mach-davinci/dm365.c b/arch/arm/mach-davinci/dm365.c
index c1e0d46996e4..7538bb87f373 100644
--- a/arch/arm/mach-davinci/dm365.c
+++ b/arch/arm/mach-davinci/dm365.c
@@ -1,16 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * TI DaVinci DM365 chip specific setup
  *
  * Copyright (C) 2009 Texas Instruments
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation version 2.
- *
- * This program is distributed "as is" WITHOUT ANY WARRANTY of any
- * kind, whether express or implied; without even the implied warranty
- * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
  */
 
 #include <linux/clk-provider.h>
@@ -29,15 +21,13 @@
 #include <linux/serial_8250.h>
 #include <linux/spi/spi.h>
 
-#include <asm/mach/map.h>
-
-#include <mach/common.h>
-#include <mach/cputype.h>
-#include <mach/mux.h>
-#include <mach/serial.h>
-
 #include <clocksource/timer-davinci.h>
 
+#include <asm/mach/map.h>
+
+#include "common.h"
+#include "cputype.h"
+#include "serial.h"
 #include "asp.h"
 #include "davinci.h"
 #include "irqs.h"
diff --git a/arch/arm/mach-davinci/dm644x.c b/arch/arm/mach-davinci/dm644x.c
deleted file mode 100644
index 24988939ae46..000000000000
--- a/arch/arm/mach-davinci/dm644x.c
+++ /dev/null
@@ -1,767 +0,0 @@
-/*
- * TI DaVinci DM644x chip specific setup
- *
- * Author: Kevin Hilman, Deep Root Systems, LLC
- *
- * 2007 (c) Deep Root Systems, LLC. This file is licensed under
- * the terms of the GNU General Public License version 2. This program
- * is licensed "as is" without any warranty of any kind, whether express
- * or implied.
- */
-
-#include <linux/clk-provider.h>
-#include <linux/clk/davinci.h>
-#include <linux/clkdev.h>
-#include <linux/dmaengine.h>
-#include <linux/init.h>
-#include <linux/io.h>
-#include <linux/irqchip/irq-davinci-aintc.h>
-#include <linux/platform_data/edma.h>
-#include <linux/platform_data/gpio-davinci.h>
-#include <linux/platform_device.h>
-#include <linux/serial_8250.h>
-
-#include <asm/mach/map.h>
-
-#include <mach/common.h>
-#include <mach/cputype.h>
-#include <mach/mux.h>
-#include <mach/serial.h>
-
-#include <clocksource/timer-davinci.h>
-
-#include "asp.h"
-#include "davinci.h"
-#include "irqs.h"
-#include "mux.h"
-
-/*
- * Device specific clocks
- */
-#define DM644X_REF_FREQ		27000000
-
-#define DM644X_EMAC_BASE		0x01c80000
-#define DM644X_EMAC_MDIO_BASE		(DM644X_EMAC_BASE + 0x4000)
-#define DM644X_EMAC_CNTRL_OFFSET	0x0000
-#define DM644X_EMAC_CNTRL_MOD_OFFSET	0x1000
-#define DM644X_EMAC_CNTRL_RAM_OFFSET	0x2000
-#define DM644X_EMAC_CNTRL_RAM_SIZE	0x2000
-
-static struct emac_platform_data dm644x_emac_pdata = {
-	.ctrl_reg_offset	= DM644X_EMAC_CNTRL_OFFSET,
-	.ctrl_mod_reg_offset	= DM644X_EMAC_CNTRL_MOD_OFFSET,
-	.ctrl_ram_offset	= DM644X_EMAC_CNTRL_RAM_OFFSET,
-	.ctrl_ram_size		= DM644X_EMAC_CNTRL_RAM_SIZE,
-	.version		= EMAC_VERSION_1,
-};
-
-static struct resource dm644x_emac_resources[] = {
-	{
-		.start	= DM644X_EMAC_BASE,
-		.end	= DM644X_EMAC_BASE + SZ_16K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	{
-		.start = DAVINCI_INTC_IRQ(IRQ_EMACINT),
-		.end   = DAVINCI_INTC_IRQ(IRQ_EMACINT),
-		.flags = IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device dm644x_emac_device = {
-       .name		= "davinci_emac",
-       .id		= 1,
-       .dev = {
-	       .platform_data	= &dm644x_emac_pdata,
-       },
-       .num_resources	= ARRAY_SIZE(dm644x_emac_resources),
-       .resource	= dm644x_emac_resources,
-};
-
-static struct resource dm644x_mdio_resources[] = {
-	{
-		.start	= DM644X_EMAC_MDIO_BASE,
-		.end	= DM644X_EMAC_MDIO_BASE + SZ_4K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-};
-
-static struct platform_device dm644x_mdio_device = {
-	.name		= "davinci_mdio",
-	.id		= 0,
-	.num_resources	= ARRAY_SIZE(dm644x_mdio_resources),
-	.resource	= dm644x_mdio_resources,
-};
-
-/*
- * Device specific mux setup
- *
- *	soc	description	mux  mode   mode  mux	 dbg
- *				reg  offset mask  mode
- */
-static const struct mux_config dm644x_pins[] = {
-#ifdef CONFIG_DAVINCI_MUX
-MUX_CFG(DM644X, HDIREN,		0,   16,    1,	  1,	 true)
-MUX_CFG(DM644X, ATAEN,		0,   17,    1,	  1,	 true)
-MUX_CFG(DM644X, ATAEN_DISABLE,	0,   17,    1,	  0,	 true)
-
-MUX_CFG(DM644X, HPIEN_DISABLE,	0,   29,    1,	  0,	 true)
-
-MUX_CFG(DM644X, AEAW,		0,   0,     31,	  31,	 true)
-MUX_CFG(DM644X, AEAW0,		0,   0,     1,	  0,	 true)
-MUX_CFG(DM644X, AEAW1,		0,   1,     1,	  0,	 true)
-MUX_CFG(DM644X, AEAW2,		0,   2,     1,	  0,	 true)
-MUX_CFG(DM644X, AEAW3,		0,   3,     1,	  0,	 true)
-MUX_CFG(DM644X, AEAW4,		0,   4,     1,	  0,	 true)
-
-MUX_CFG(DM644X, MSTK,		1,   9,     1,	  0,	 false)
-
-MUX_CFG(DM644X, I2C,		1,   7,     1,	  1,	 false)
-
-MUX_CFG(DM644X, MCBSP,		1,   10,    1,	  1,	 false)
-
-MUX_CFG(DM644X, UART1,		1,   1,     1,	  1,	 true)
-MUX_CFG(DM644X, UART2,		1,   2,     1,	  1,	 true)
-
-MUX_CFG(DM644X, PWM0,		1,   4,     1,	  1,	 false)
-
-MUX_CFG(DM644X, PWM1,		1,   5,     1,	  1,	 false)
-
-MUX_CFG(DM644X, PWM2,		1,   6,     1,	  1,	 false)
-
-MUX_CFG(DM644X, VLYNQEN,	0,   15,    1,	  1,	 false)
-MUX_CFG(DM644X, VLSCREN,	0,   14,    1,	  1,	 false)
-MUX_CFG(DM644X, VLYNQWD,	0,   12,    3,	  3,	 false)
-
-MUX_CFG(DM644X, EMACEN,		0,   31,    1,	  1,	 true)
-
-MUX_CFG(DM644X, GPIO3V,		0,   31,    1,	  0,	 true)
-
-MUX_CFG(DM644X, GPIO0,		0,   24,    1,	  0,	 true)
-MUX_CFG(DM644X, GPIO3,		0,   25,    1,	  0,	 false)
-MUX_CFG(DM644X, GPIO43_44,	1,   7,     1,	  0,	 false)
-MUX_CFG(DM644X, GPIO46_47,	0,   22,    1,	  0,	 true)
-
-MUX_CFG(DM644X, RGB666,		0,   22,    1,	  1,	 true)
-
-MUX_CFG(DM644X, LOEEN,		0,   24,    1,	  1,	 true)
-MUX_CFG(DM644X, LFLDEN,		0,   25,    1,	  1,	 false)
-#endif
-};
-
-/* FIQ are pri 0-1; otherwise 2-7, with 7 lowest priority */
-static u8 dm644x_default_priorities[DAVINCI_N_AINTC_IRQ] = {
-	[IRQ_VDINT0]		= 2,
-	[IRQ_VDINT1]		= 6,
-	[IRQ_VDINT2]		= 6,
-	[IRQ_HISTINT]		= 6,
-	[IRQ_H3AINT]		= 6,
-	[IRQ_PRVUINT]		= 6,
-	[IRQ_RSZINT]		= 6,
-	[7]			= 7,
-	[IRQ_VENCINT]		= 6,
-	[IRQ_ASQINT]		= 6,
-	[IRQ_IMXINT]		= 6,
-	[IRQ_VLCDINT]		= 6,
-	[IRQ_USBINT]		= 4,
-	[IRQ_EMACINT]		= 4,
-	[14]			= 7,
-	[15]			= 7,
-	[IRQ_CCINT0]		= 5,	/* dma */
-	[IRQ_CCERRINT]		= 5,	/* dma */
-	[IRQ_TCERRINT0]		= 5,	/* dma */
-	[IRQ_TCERRINT]		= 5,	/* dma */
-	[IRQ_PSCIN]		= 7,
-	[21]			= 7,
-	[IRQ_IDE]		= 4,
-	[23]			= 7,
-	[IRQ_MBXINT]		= 7,
-	[IRQ_MBRINT]		= 7,
-	[IRQ_MMCINT]		= 7,
-	[IRQ_SDIOINT]		= 7,
-	[28]			= 7,
-	[IRQ_DDRINT]		= 7,
-	[IRQ_AEMIFINT]		= 7,
-	[IRQ_VLQINT]		= 4,
-	[IRQ_TINT0_TINT12]	= 2,	/* clockevent */
-	[IRQ_TINT0_TINT34]	= 2,	/* clocksource */
-	[IRQ_TINT1_TINT12]	= 7,	/* DSP timer */
-	[IRQ_TINT1_TINT34]	= 7,	/* system tick */
-	[IRQ_PWMINT0]		= 7,
-	[IRQ_PWMINT1]		= 7,
-	[IRQ_PWMINT2]		= 7,
-	[IRQ_I2C]		= 3,
-	[IRQ_UARTINT0]		= 3,
-	[IRQ_UARTINT1]		= 3,
-	[IRQ_UARTINT2]		= 3,
-	[IRQ_SPINT0]		= 3,
-	[IRQ_SPINT1]		= 3,
-	[45]			= 7,
-	[IRQ_DSP2ARM0]		= 4,
-	[IRQ_DSP2ARM1]		= 4,
-	[IRQ_GPIO0]		= 7,
-	[IRQ_GPIO1]		= 7,
-	[IRQ_GPIO2]		= 7,
-	[IRQ_GPIO3]		= 7,
-	[IRQ_GPIO4]		= 7,
-	[IRQ_GPIO5]		= 7,
-	[IRQ_GPIO6]		= 7,
-	[IRQ_GPIO7]		= 7,
-	[IRQ_GPIOBNK0]		= 7,
-	[IRQ_GPIOBNK1]		= 7,
-	[IRQ_GPIOBNK2]		= 7,
-	[IRQ_GPIOBNK3]		= 7,
-	[IRQ_GPIOBNK4]		= 7,
-	[IRQ_COMMTX]		= 7,
-	[IRQ_COMMRX]		= 7,
-	[IRQ_EMUINT]		= 7,
-};
-
-/*----------------------------------------------------------------------*/
-
-static s8 queue_priority_mapping[][2] = {
-	/* {event queue no, Priority} */
-	{0, 3},
-	{1, 7},
-	{-1, -1},
-};
-
-static const struct dma_slave_map dm644x_edma_map[] = {
-	{ "davinci-mcbsp", "tx", EDMA_FILTER_PARAM(0, 2) },
-	{ "davinci-mcbsp", "rx", EDMA_FILTER_PARAM(0, 3) },
-	{ "spi_davinci", "tx", EDMA_FILTER_PARAM(0, 16) },
-	{ "spi_davinci", "rx", EDMA_FILTER_PARAM(0, 17) },
-	{ "dm6441-mmc.0", "rx", EDMA_FILTER_PARAM(0, 26) },
-	{ "dm6441-mmc.0", "tx", EDMA_FILTER_PARAM(0, 27) },
-};
-
-static struct edma_soc_info dm644x_edma_pdata = {
-	.queue_priority_mapping	= queue_priority_mapping,
-	.default_queue		= EVENTQ_1,
-	.slave_map		= dm644x_edma_map,
-	.slavecnt		= ARRAY_SIZE(dm644x_edma_map),
-};
-
-static struct resource edma_resources[] = {
-	{
-		.name	= "edma3_cc",
-		.start	= 0x01c00000,
-		.end	= 0x01c00000 + SZ_64K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	{
-		.name	= "edma3_tc0",
-		.start	= 0x01c10000,
-		.end	= 0x01c10000 + SZ_1K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	{
-		.name	= "edma3_tc1",
-		.start	= 0x01c10400,
-		.end	= 0x01c10400 + SZ_1K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	{
-		.name	= "edma3_ccint",
-		.start	= DAVINCI_INTC_IRQ(IRQ_CCINT0),
-		.flags	= IORESOURCE_IRQ,
-	},
-	{
-		.name	= "edma3_ccerrint",
-		.start	= DAVINCI_INTC_IRQ(IRQ_CCERRINT),
-		.flags	= IORESOURCE_IRQ,
-	},
-	/* not using TC*_ERR */
-};
-
-static const struct platform_device_info dm644x_edma_device __initconst = {
-	.name		= "edma",
-	.id		= 0,
-	.dma_mask	= DMA_BIT_MASK(32),
-	.res		= edma_resources,
-	.num_res	= ARRAY_SIZE(edma_resources),
-	.data		= &dm644x_edma_pdata,
-	.size_data	= sizeof(dm644x_edma_pdata),
-};
-
-/* DM6446 EVM uses ASP0; line-out is a pair of RCA jacks */
-static struct resource dm644x_asp_resources[] = {
-	{
-		.name	= "mpu",
-		.start	= DAVINCI_ASP0_BASE,
-		.end	= DAVINCI_ASP0_BASE + SZ_8K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	{
-		.start	= DAVINCI_DMA_ASP0_TX,
-		.end	= DAVINCI_DMA_ASP0_TX,
-		.flags	= IORESOURCE_DMA,
-	},
-	{
-		.start	= DAVINCI_DMA_ASP0_RX,
-		.end	= DAVINCI_DMA_ASP0_RX,
-		.flags	= IORESOURCE_DMA,
-	},
-};
-
-static struct platform_device dm644x_asp_device = {
-	.name		= "davinci-mcbsp",
-	.id		= -1,
-	.num_resources	= ARRAY_SIZE(dm644x_asp_resources),
-	.resource	= dm644x_asp_resources,
-};
-
-#define DM644X_VPSS_BASE	0x01c73400
-
-static struct resource dm644x_vpss_resources[] = {
-	{
-		/* VPSS Base address */
-		.name		= "vpss",
-		.start		= DM644X_VPSS_BASE,
-		.end		= DM644X_VPSS_BASE + 0xff,
-		.flags		= IORESOURCE_MEM,
-	},
-};
-
-static struct platform_device dm644x_vpss_device = {
-	.name			= "vpss",
-	.id			= -1,
-	.dev.platform_data	= "dm644x_vpss",
-	.num_resources		= ARRAY_SIZE(dm644x_vpss_resources),
-	.resource		= dm644x_vpss_resources,
-};
-
-static struct resource dm644x_vpfe_resources[] = {
-	{
-		.start          = DAVINCI_INTC_IRQ(IRQ_VDINT0),
-		.end            = DAVINCI_INTC_IRQ(IRQ_VDINT0),
-		.flags          = IORESOURCE_IRQ,
-	},
-	{
-		.start          = DAVINCI_INTC_IRQ(IRQ_VDINT1),
-		.end            = DAVINCI_INTC_IRQ(IRQ_VDINT1),
-		.flags          = IORESOURCE_IRQ,
-	},
-};
-
-static u64 dm644x_video_dma_mask = DMA_BIT_MASK(32);
-static struct resource dm644x_ccdc_resource[] = {
-	/* CCDC Base address */
-	{
-		.start          = 0x01c70400,
-		.end            = 0x01c70400 + 0xff,
-		.flags          = IORESOURCE_MEM,
-	},
-};
-
-static struct platform_device dm644x_ccdc_dev = {
-	.name           = "dm644x_ccdc",
-	.id             = -1,
-	.num_resources  = ARRAY_SIZE(dm644x_ccdc_resource),
-	.resource       = dm644x_ccdc_resource,
-	.dev = {
-		.dma_mask               = &dm644x_video_dma_mask,
-		.coherent_dma_mask      = DMA_BIT_MASK(32),
-	},
-};
-
-static struct platform_device dm644x_vpfe_dev = {
-	.name		= CAPTURE_DRV_NAME,
-	.id		= -1,
-	.num_resources	= ARRAY_SIZE(dm644x_vpfe_resources),
-	.resource	= dm644x_vpfe_resources,
-	.dev = {
-		.dma_mask		= &dm644x_video_dma_mask,
-		.coherent_dma_mask	= DMA_BIT_MASK(32),
-	},
-};
-
-#define DM644X_OSD_BASE		0x01c72600
-
-static struct resource dm644x_osd_resources[] = {
-	{
-		.start	= DM644X_OSD_BASE,
-		.end	= DM644X_OSD_BASE + 0x1ff,
-		.flags	= IORESOURCE_MEM,
-	},
-};
-
-static struct platform_device dm644x_osd_dev = {
-	.name		= DM644X_VPBE_OSD_SUBDEV_NAME,
-	.id		= -1,
-	.num_resources	= ARRAY_SIZE(dm644x_osd_resources),
-	.resource	= dm644x_osd_resources,
-	.dev		= {
-		.dma_mask		= &dm644x_video_dma_mask,
-		.coherent_dma_mask	= DMA_BIT_MASK(32),
-	},
-};
-
-#define DM644X_VENC_BASE		0x01c72400
-
-static struct resource dm644x_venc_resources[] = {
-	{
-		.start	= DM644X_VENC_BASE,
-		.end	= DM644X_VENC_BASE + 0x17f,
-		.flags	= IORESOURCE_MEM,
-	},
-};
-
-#define DM644X_VPSS_MUXSEL_PLL2_MODE          BIT(0)
-#define DM644X_VPSS_MUXSEL_VPBECLK_MODE       BIT(1)
-#define DM644X_VPSS_VENCLKEN                  BIT(3)
-#define DM644X_VPSS_DACCLKEN                  BIT(4)
-
-static int dm644x_venc_setup_clock(enum vpbe_enc_timings_type type,
-				   unsigned int pclock)
-{
-	int ret = 0;
-	u32 v = DM644X_VPSS_VENCLKEN;
-
-	switch (type) {
-	case VPBE_ENC_STD:
-		v |= DM644X_VPSS_DACCLKEN;
-		writel(v, DAVINCI_SYSMOD_VIRT(SYSMOD_VPSS_CLKCTL));
-		break;
-	case VPBE_ENC_DV_TIMINGS:
-		if (pclock <= 27000000) {
-			v |= DM644X_VPSS_DACCLKEN;
-			writel(v, DAVINCI_SYSMOD_VIRT(SYSMOD_VPSS_CLKCTL));
-		} else {
-			/*
-			 * For HD, use external clock source since
-			 * HD requires higher clock rate
-			 */
-			v |= DM644X_VPSS_MUXSEL_VPBECLK_MODE;
-			writel(v, DAVINCI_SYSMOD_VIRT(SYSMOD_VPSS_CLKCTL));
-		}
-		break;
-	default:
-		ret  = -EINVAL;
-	}
-
-	return ret;
-}
-
-static struct resource dm644x_v4l2_disp_resources[] = {
-	{
-		.start	= DAVINCI_INTC_IRQ(IRQ_VENCINT),
-		.end	= DAVINCI_INTC_IRQ(IRQ_VENCINT),
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device dm644x_vpbe_display = {
-	.name		= "vpbe-v4l2",
-	.id		= -1,
-	.num_resources	= ARRAY_SIZE(dm644x_v4l2_disp_resources),
-	.resource	= dm644x_v4l2_disp_resources,
-	.dev		= {
-		.dma_mask		= &dm644x_video_dma_mask,
-		.coherent_dma_mask	= DMA_BIT_MASK(32),
-	},
-};
-
-static struct venc_platform_data dm644x_venc_pdata = {
-	.setup_clock	= dm644x_venc_setup_clock,
-};
-
-static struct platform_device dm644x_venc_dev = {
-	.name		= DM644X_VPBE_VENC_SUBDEV_NAME,
-	.id		= -1,
-	.num_resources	= ARRAY_SIZE(dm644x_venc_resources),
-	.resource	= dm644x_venc_resources,
-	.dev		= {
-		.dma_mask		= &dm644x_video_dma_mask,
-		.coherent_dma_mask	= DMA_BIT_MASK(32),
-		.platform_data		= &dm644x_venc_pdata,
-	},
-};
-
-static struct platform_device dm644x_vpbe_dev = {
-	.name		= "vpbe_controller",
-	.id		= -1,
-	.dev		= {
-		.dma_mask		= &dm644x_video_dma_mask,
-		.coherent_dma_mask	= DMA_BIT_MASK(32),
-	},
-};
-
-static struct resource dm644_gpio_resources[] = {
-	{	/* registers */
-		.start	= DAVINCI_GPIO_BASE,
-		.end	= DAVINCI_GPIO_BASE + SZ_4K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	{	/* interrupt */
-		.start	= DAVINCI_INTC_IRQ(IRQ_GPIOBNK0),
-		.end	= DAVINCI_INTC_IRQ(IRQ_GPIOBNK0),
-		.flags	= IORESOURCE_IRQ,
-	},
-	{
-		.start	= DAVINCI_INTC_IRQ(IRQ_GPIOBNK1),
-		.end	= DAVINCI_INTC_IRQ(IRQ_GPIOBNK1),
-		.flags	= IORESOURCE_IRQ,
-	},
-	{
-		.start	= DAVINCI_INTC_IRQ(IRQ_GPIOBNK2),
-		.end	= DAVINCI_INTC_IRQ(IRQ_GPIOBNK2),
-		.flags	= IORESOURCE_IRQ,
-	},
-	{
-		.start	= DAVINCI_INTC_IRQ(IRQ_GPIOBNK3),
-		.end	= DAVINCI_INTC_IRQ(IRQ_GPIOBNK3),
-		.flags	= IORESOURCE_IRQ,
-	},
-	{
-		.start	= DAVINCI_INTC_IRQ(IRQ_GPIOBNK4),
-		.end	= DAVINCI_INTC_IRQ(IRQ_GPIOBNK4),
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct davinci_gpio_platform_data dm644_gpio_platform_data = {
-	.no_auto_base	= true,
-	.base		= 0,
-	.ngpio		= 71,
-};
-
-int __init dm644x_gpio_register(void)
-{
-	return davinci_gpio_register(dm644_gpio_resources,
-				     ARRAY_SIZE(dm644_gpio_resources),
-				     &dm644_gpio_platform_data);
-}
-/*----------------------------------------------------------------------*/
-
-static struct map_desc dm644x_io_desc[] = {
-	{
-		.virtual	= IO_VIRT,
-		.pfn		= __phys_to_pfn(IO_PHYS),
-		.length		= IO_SIZE,
-		.type		= MT_DEVICE
-	},
-};
-
-/* Contents of JTAG ID register used to identify exact cpu type */
-static struct davinci_id dm644x_ids[] = {
-	{
-		.variant	= 0x0,
-		.part_no	= 0xb700,
-		.manufacturer	= 0x017,
-		.cpu_id		= DAVINCI_CPU_ID_DM6446,
-		.name		= "dm6446",
-	},
-	{
-		.variant	= 0x1,
-		.part_no	= 0xb700,
-		.manufacturer	= 0x017,
-		.cpu_id		= DAVINCI_CPU_ID_DM6446,
-		.name		= "dm6446a",
-	},
-};
-
-/*
- * Bottom half of timer0 is used for clockevent, top half is used for
- * clocksource.
- */
-static const struct davinci_timer_cfg dm644x_timer_cfg = {
-	.reg = DEFINE_RES_IO(DAVINCI_TIMER0_BASE, SZ_4K),
-	.irq = {
-		DEFINE_RES_IRQ(DAVINCI_INTC_IRQ(IRQ_TINT0_TINT12)),
-		DEFINE_RES_IRQ(DAVINCI_INTC_IRQ(IRQ_TINT0_TINT34)),
-	},
-};
-
-static struct plat_serial8250_port dm644x_serial0_platform_data[] = {
-	{
-		.mapbase	= DAVINCI_UART0_BASE,
-		.irq		= DAVINCI_INTC_IRQ(IRQ_UARTINT0),
-		.flags		= UPF_BOOT_AUTOCONF | UPF_SKIP_TEST |
-				  UPF_IOREMAP,
-		.iotype		= UPIO_MEM,
-		.regshift	= 2,
-	},
-	{
-		.flags	= 0,
-	}
-};
-static struct plat_serial8250_port dm644x_serial1_platform_data[] = {
-	{
-		.mapbase	= DAVINCI_UART1_BASE,
-		.irq		= DAVINCI_INTC_IRQ(IRQ_UARTINT1),
-		.flags		= UPF_BOOT_AUTOCONF | UPF_SKIP_TEST |
-				  UPF_IOREMAP,
-		.iotype		= UPIO_MEM,
-		.regshift	= 2,
-	},
-	{
-		.flags	= 0,
-	}
-};
-static struct plat_serial8250_port dm644x_serial2_platform_data[] = {
-	{
-		.mapbase	= DAVINCI_UART2_BASE,
-		.irq		= DAVINCI_INTC_IRQ(IRQ_UARTINT2),
-		.flags		= UPF_BOOT_AUTOCONF | UPF_SKIP_TEST |
-				  UPF_IOREMAP,
-		.iotype		= UPIO_MEM,
-		.regshift	= 2,
-	},
-	{
-		.flags	= 0,
-	}
-};
-
-struct platform_device dm644x_serial_device[] = {
-	{
-		.name			= "serial8250",
-		.id			= PLAT8250_DEV_PLATFORM,
-		.dev			= {
-			.platform_data	= dm644x_serial0_platform_data,
-		}
-	},
-	{
-		.name			= "serial8250",
-		.id			= PLAT8250_DEV_PLATFORM1,
-		.dev			= {
-			.platform_data	= dm644x_serial1_platform_data,
-		}
-	},
-	{
-		.name			= "serial8250",
-		.id			= PLAT8250_DEV_PLATFORM2,
-		.dev			= {
-			.platform_data	= dm644x_serial2_platform_data,
-		}
-	},
-	{
-	}
-};
-
-static const struct davinci_soc_info davinci_soc_info_dm644x = {
-	.io_desc		= dm644x_io_desc,
-	.io_desc_num		= ARRAY_SIZE(dm644x_io_desc),
-	.jtag_id_reg		= 0x01c40028,
-	.ids			= dm644x_ids,
-	.ids_num		= ARRAY_SIZE(dm644x_ids),
-	.pinmux_base		= DAVINCI_SYSTEM_MODULE_BASE,
-	.pinmux_pins		= dm644x_pins,
-	.pinmux_pins_num	= ARRAY_SIZE(dm644x_pins),
-	.emac_pdata		= &dm644x_emac_pdata,
-	.sram_dma		= 0x00008000,
-	.sram_len		= SZ_16K,
-};
-
-void __init dm644x_init_asp(void)
-{
-	davinci_cfg_reg(DM644X_MCBSP);
-	platform_device_register(&dm644x_asp_device);
-}
-
-void __init dm644x_init(void)
-{
-	davinci_common_init(&davinci_soc_info_dm644x);
-	davinci_map_sysmod();
-}
-
-void __init dm644x_init_time(void)
-{
-	void __iomem *pll1, *psc;
-	struct clk *clk;
-	int rv;
-
-	clk_register_fixed_rate(NULL, "ref_clk", NULL, 0, DM644X_REF_FREQ);
-
-	pll1 = ioremap(DAVINCI_PLL1_BASE, SZ_1K);
-	dm644x_pll1_init(NULL, pll1, NULL);
-
-	psc = ioremap(DAVINCI_PWR_SLEEP_CNTRL_BASE, SZ_4K);
-	dm644x_psc_init(NULL, psc);
-
-	clk = clk_get(NULL, "timer0");
-	if (WARN_ON(IS_ERR(clk))) {
-		pr_err("Unable to get the timer clock\n");
-		return;
-	}
-
-	rv = davinci_timer_register(clk, &dm644x_timer_cfg);
-	WARN(rv, "Unable to register the timer: %d\n", rv);
-}
-
-static struct resource dm644x_pll2_resources[] = {
-	{
-		.start	= DAVINCI_PLL2_BASE,
-		.end	= DAVINCI_PLL2_BASE + SZ_1K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-};
-
-static struct platform_device dm644x_pll2_device = {
-	.name		= "dm644x-pll2",
-	.id		= -1,
-	.resource	= dm644x_pll2_resources,
-	.num_resources	= ARRAY_SIZE(dm644x_pll2_resources),
-};
-
-void __init dm644x_register_clocks(void)
-{
-	/* PLL1 and PSC are registered in dm644x_init_time() */
-	platform_device_register(&dm644x_pll2_device);
-}
-
-int __init dm644x_init_video(struct vpfe_config *vpfe_cfg,
-				struct vpbe_config *vpbe_cfg)
-{
-	if (vpfe_cfg || vpbe_cfg)
-		platform_device_register(&dm644x_vpss_device);
-
-	if (vpfe_cfg) {
-		dm644x_vpfe_dev.dev.platform_data = vpfe_cfg;
-		platform_device_register(&dm644x_ccdc_dev);
-		platform_device_register(&dm644x_vpfe_dev);
-	}
-
-	if (vpbe_cfg) {
-		dm644x_vpbe_dev.dev.platform_data = vpbe_cfg;
-		platform_device_register(&dm644x_osd_dev);
-		platform_device_register(&dm644x_venc_dev);
-		platform_device_register(&dm644x_vpbe_dev);
-		platform_device_register(&dm644x_vpbe_display);
-	}
-
-	return 0;
-}
-
-static const struct davinci_aintc_config dm644x_aintc_config = {
-	.reg = {
-		.start		= DAVINCI_ARM_INTC_BASE,
-		.end		= DAVINCI_ARM_INTC_BASE + SZ_4K - 1,
-		.flags		= IORESOURCE_MEM,
-	},
-	.num_irqs		= 64,
-	.prios			= dm644x_default_priorities,
-};
-
-void __init dm644x_init_irq(void)
-{
-	davinci_aintc_init(&dm644x_aintc_config);
-}
-
-void __init dm644x_init_devices(void)
-{
-	struct platform_device *edma_pdev;
-	int ret;
-
-	edma_pdev = platform_device_register_full(&dm644x_edma_device);
-	if (IS_ERR(edma_pdev))
-		pr_warn("%s: Failed to register eDMA\n", __func__);
-
-	platform_device_register(&dm644x_mdio_device);
-	platform_device_register(&dm644x_emac_device);
-
-	ret = davinci_init_wdt();
-	if (ret)
-		pr_warn("%s: watchdog init failed: %d\n", __func__, ret);
-
-}
diff --git a/arch/arm/mach-davinci/dm646x.c b/arch/arm/mach-davinci/dm646x.c
deleted file mode 100644
index 4ffd028ed997..000000000000
--- a/arch/arm/mach-davinci/dm646x.c
+++ /dev/null
@@ -1,728 +0,0 @@
-/*
- * TI DaVinci DM646x chip specific setup
- *
- * Author: Kevin Hilman, Deep Root Systems, LLC
- *
- * 2007 (c) Deep Root Systems, LLC. This file is licensed under
- * the terms of the GNU General Public License version 2. This program
- * is licensed "as is" without any warranty of any kind, whether express
- * or implied.
- */
-
-#include <linux/clk-provider.h>
-#include <linux/clk/davinci.h>
-#include <linux/clkdev.h>
-#include <linux/dma-mapping.h>
-#include <linux/dmaengine.h>
-#include <linux/init.h>
-#include <linux/io.h>
-#include <linux/irqchip/irq-davinci-aintc.h>
-#include <linux/platform_data/edma.h>
-#include <linux/platform_data/gpio-davinci.h>
-#include <linux/platform_device.h>
-#include <linux/serial_8250.h>
-
-#include <asm/mach/map.h>
-
-#include <mach/common.h>
-#include <mach/cputype.h>
-#include <mach/mux.h>
-#include <mach/serial.h>
-
-#include <clocksource/timer-davinci.h>
-
-#include "asp.h"
-#include "davinci.h"
-#include "irqs.h"
-#include "mux.h"
-
-#define DAVINCI_VPIF_BASE       (0x01C12000)
-
-#define VDD3P3V_VID_MASK	(BIT_MASK(3) | BIT_MASK(2) | BIT_MASK(1) |\
-					BIT_MASK(0))
-#define VSCLKDIS_MASK		(BIT_MASK(11) | BIT_MASK(10) | BIT_MASK(9) |\
-					BIT_MASK(8))
-
-#define DM646X_EMAC_BASE		0x01c80000
-#define DM646X_EMAC_MDIO_BASE		(DM646X_EMAC_BASE + 0x4000)
-#define DM646X_EMAC_CNTRL_OFFSET	0x0000
-#define DM646X_EMAC_CNTRL_MOD_OFFSET	0x1000
-#define DM646X_EMAC_CNTRL_RAM_OFFSET	0x2000
-#define DM646X_EMAC_CNTRL_RAM_SIZE	0x2000
-
-static struct emac_platform_data dm646x_emac_pdata = {
-	.ctrl_reg_offset	= DM646X_EMAC_CNTRL_OFFSET,
-	.ctrl_mod_reg_offset	= DM646X_EMAC_CNTRL_MOD_OFFSET,
-	.ctrl_ram_offset	= DM646X_EMAC_CNTRL_RAM_OFFSET,
-	.ctrl_ram_size		= DM646X_EMAC_CNTRL_RAM_SIZE,
-	.version		= EMAC_VERSION_2,
-};
-
-static struct resource dm646x_emac_resources[] = {
-	{
-		.start	= DM646X_EMAC_BASE,
-		.end	= DM646X_EMAC_BASE + SZ_16K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	{
-		.start	= DAVINCI_INTC_IRQ(IRQ_DM646X_EMACRXTHINT),
-		.end	= DAVINCI_INTC_IRQ(IRQ_DM646X_EMACRXTHINT),
-		.flags	= IORESOURCE_IRQ,
-	},
-	{
-		.start	= DAVINCI_INTC_IRQ(IRQ_DM646X_EMACRXINT),
-		.end	= DAVINCI_INTC_IRQ(IRQ_DM646X_EMACRXINT),
-		.flags	= IORESOURCE_IRQ,
-	},
-	{
-		.start	= DAVINCI_INTC_IRQ(IRQ_DM646X_EMACTXINT),
-		.end	= DAVINCI_INTC_IRQ(IRQ_DM646X_EMACTXINT),
-		.flags	= IORESOURCE_IRQ,
-	},
-	{
-		.start	= DAVINCI_INTC_IRQ(IRQ_DM646X_EMACMISCINT),
-		.end	= DAVINCI_INTC_IRQ(IRQ_DM646X_EMACMISCINT),
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device dm646x_emac_device = {
-	.name		= "davinci_emac",
-	.id		= 1,
-	.dev = {
-		.platform_data	= &dm646x_emac_pdata,
-	},
-	.num_resources	= ARRAY_SIZE(dm646x_emac_resources),
-	.resource	= dm646x_emac_resources,
-};
-
-static struct resource dm646x_mdio_resources[] = {
-	{
-		.start	= DM646X_EMAC_MDIO_BASE,
-		.end	= DM646X_EMAC_MDIO_BASE + SZ_4K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-};
-
-static struct platform_device dm646x_mdio_device = {
-	.name		= "davinci_mdio",
-	.id		= 0,
-	.num_resources	= ARRAY_SIZE(dm646x_mdio_resources),
-	.resource	= dm646x_mdio_resources,
-};
-
-/*
- * Device specific mux setup
- *
- *	soc	description	mux  mode   mode  mux	 dbg
- *				reg  offset mask  mode
- */
-static const struct mux_config dm646x_pins[] = {
-#ifdef CONFIG_DAVINCI_MUX
-MUX_CFG(DM646X, ATAEN,		0,   0,     5,	  1,	 true)
-
-MUX_CFG(DM646X, AUDCK1,		0,   29,    1,	  0,	 false)
-
-MUX_CFG(DM646X, AUDCK0,		0,   28,    1,	  0,	 false)
-
-MUX_CFG(DM646X, CRGMUX,			0,   24,    7,    5,	 true)
-
-MUX_CFG(DM646X, STSOMUX_DISABLE,	0,   22,    3,    0,	 true)
-
-MUX_CFG(DM646X, STSIMUX_DISABLE,	0,   20,    3,    0,	 true)
-
-MUX_CFG(DM646X, PTSOMUX_DISABLE,	0,   18,    3,    0,	 true)
-
-MUX_CFG(DM646X, PTSIMUX_DISABLE,	0,   16,    3,    0,	 true)
-
-MUX_CFG(DM646X, STSOMUX,		0,   22,    3,    2,	 true)
-
-MUX_CFG(DM646X, STSIMUX,		0,   20,    3,    2,	 true)
-
-MUX_CFG(DM646X, PTSOMUX_PARALLEL,	0,   18,    3,    2,	 true)
-
-MUX_CFG(DM646X, PTSIMUX_PARALLEL,	0,   16,    3,    2,	 true)
-
-MUX_CFG(DM646X, PTSOMUX_SERIAL,		0,   18,    3,    3,	 true)
-
-MUX_CFG(DM646X, PTSIMUX_SERIAL,		0,   16,    3,    3,	 true)
-#endif
-};
-
-static u8 dm646x_default_priorities[DAVINCI_N_AINTC_IRQ] = {
-	[IRQ_DM646X_VP_VERTINT0]        = 7,
-	[IRQ_DM646X_VP_VERTINT1]        = 7,
-	[IRQ_DM646X_VP_VERTINT2]        = 7,
-	[IRQ_DM646X_VP_VERTINT3]        = 7,
-	[IRQ_DM646X_VP_ERRINT]          = 7,
-	[IRQ_DM646X_RESERVED_1]         = 7,
-	[IRQ_DM646X_RESERVED_2]         = 7,
-	[IRQ_DM646X_WDINT]              = 7,
-	[IRQ_DM646X_CRGENINT0]          = 7,
-	[IRQ_DM646X_CRGENINT1]          = 7,
-	[IRQ_DM646X_TSIFINT0]           = 7,
-	[IRQ_DM646X_TSIFINT1]           = 7,
-	[IRQ_DM646X_VDCEINT]            = 7,
-	[IRQ_DM646X_USBINT]             = 7,
-	[IRQ_DM646X_USBDMAINT]          = 7,
-	[IRQ_DM646X_PCIINT]             = 7,
-	[IRQ_CCINT0]                    = 7,    /* dma */
-	[IRQ_CCERRINT]                  = 7,    /* dma */
-	[IRQ_TCERRINT0]                 = 7,    /* dma */
-	[IRQ_TCERRINT]                  = 7,    /* dma */
-	[IRQ_DM646X_TCERRINT2]          = 7,
-	[IRQ_DM646X_TCERRINT3]          = 7,
-	[IRQ_DM646X_IDE]                = 7,
-	[IRQ_DM646X_HPIINT]             = 7,
-	[IRQ_DM646X_EMACRXTHINT]        = 7,
-	[IRQ_DM646X_EMACRXINT]          = 7,
-	[IRQ_DM646X_EMACTXINT]          = 7,
-	[IRQ_DM646X_EMACMISCINT]        = 7,
-	[IRQ_DM646X_MCASP0TXINT]        = 7,
-	[IRQ_DM646X_MCASP0RXINT]        = 7,
-	[IRQ_DM646X_RESERVED_3]         = 7,
-	[IRQ_DM646X_MCASP1TXINT]        = 7,
-	[IRQ_TINT0_TINT12]              = 7,    /* clockevent */
-	[IRQ_TINT0_TINT34]              = 7,    /* clocksource */
-	[IRQ_TINT1_TINT12]              = 7,    /* DSP timer */
-	[IRQ_TINT1_TINT34]              = 7,    /* system tick */
-	[IRQ_PWMINT0]                   = 7,
-	[IRQ_PWMINT1]                   = 7,
-	[IRQ_DM646X_VLQINT]             = 7,
-	[IRQ_I2C]                       = 7,
-	[IRQ_UARTINT0]                  = 7,
-	[IRQ_UARTINT1]                  = 7,
-	[IRQ_DM646X_UARTINT2]           = 7,
-	[IRQ_DM646X_SPINT0]             = 7,
-	[IRQ_DM646X_SPINT1]             = 7,
-	[IRQ_DM646X_DSP2ARMINT]         = 7,
-	[IRQ_DM646X_RESERVED_4]         = 7,
-	[IRQ_DM646X_PSCINT]             = 7,
-	[IRQ_DM646X_GPIO0]              = 7,
-	[IRQ_DM646X_GPIO1]              = 7,
-	[IRQ_DM646X_GPIO2]              = 7,
-	[IRQ_DM646X_GPIO3]              = 7,
-	[IRQ_DM646X_GPIO4]              = 7,
-	[IRQ_DM646X_GPIO5]              = 7,
-	[IRQ_DM646X_GPIO6]              = 7,
-	[IRQ_DM646X_GPIO7]              = 7,
-	[IRQ_DM646X_GPIOBNK0]           = 7,
-	[IRQ_DM646X_GPIOBNK1]           = 7,
-	[IRQ_DM646X_GPIOBNK2]           = 7,
-	[IRQ_DM646X_DDRINT]             = 7,
-	[IRQ_DM646X_AEMIFINT]           = 7,
-	[IRQ_COMMTX]                    = 7,
-	[IRQ_COMMRX]                    = 7,
-	[IRQ_EMUINT]                    = 7,
-};
-
-/*----------------------------------------------------------------------*/
-
-/* Four Transfer Controllers on DM646x */
-static s8 dm646x_queue_priority_mapping[][2] = {
-	/* {event queue no, Priority} */
-	{0, 4},
-	{1, 0},
-	{2, 5},
-	{3, 1},
-	{-1, -1},
-};
-
-static const struct dma_slave_map dm646x_edma_map[] = {
-	{ "davinci-mcasp.0", "tx", EDMA_FILTER_PARAM(0, 6) },
-	{ "davinci-mcasp.0", "rx", EDMA_FILTER_PARAM(0, 9) },
-	{ "davinci-mcasp.1", "tx", EDMA_FILTER_PARAM(0, 12) },
-	{ "spi_davinci", "tx", EDMA_FILTER_PARAM(0, 16) },
-	{ "spi_davinci", "rx", EDMA_FILTER_PARAM(0, 17) },
-};
-
-static struct edma_soc_info dm646x_edma_pdata = {
-	.queue_priority_mapping	= dm646x_queue_priority_mapping,
-	.default_queue		= EVENTQ_1,
-	.slave_map		= dm646x_edma_map,
-	.slavecnt		= ARRAY_SIZE(dm646x_edma_map),
-};
-
-static struct resource edma_resources[] = {
-	{
-		.name	= "edma3_cc",
-		.start	= 0x01c00000,
-		.end	= 0x01c00000 + SZ_64K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	{
-		.name	= "edma3_tc0",
-		.start	= 0x01c10000,
-		.end	= 0x01c10000 + SZ_1K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	{
-		.name	= "edma3_tc1",
-		.start	= 0x01c10400,
-		.end	= 0x01c10400 + SZ_1K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	{
-		.name	= "edma3_tc2",
-		.start	= 0x01c10800,
-		.end	= 0x01c10800 + SZ_1K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	{
-		.name	= "edma3_tc3",
-		.start	= 0x01c10c00,
-		.end	= 0x01c10c00 + SZ_1K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	{
-		.name	= "edma3_ccint",
-		.start	= DAVINCI_INTC_IRQ(IRQ_CCINT0),
-		.flags	= IORESOURCE_IRQ,
-	},
-	{
-		.name	= "edma3_ccerrint",
-		.start	= DAVINCI_INTC_IRQ(IRQ_CCERRINT),
-		.flags	= IORESOURCE_IRQ,
-	},
-	/* not using TC*_ERR */
-};
-
-static const struct platform_device_info dm646x_edma_device __initconst = {
-	.name		= "edma",
-	.id		= 0,
-	.dma_mask	= DMA_BIT_MASK(32),
-	.res		= edma_resources,
-	.num_res	= ARRAY_SIZE(edma_resources),
-	.data		= &dm646x_edma_pdata,
-	.size_data	= sizeof(dm646x_edma_pdata),
-};
-
-static struct resource dm646x_mcasp0_resources[] = {
-	{
-		.name	= "mpu",
-		.start 	= DAVINCI_DM646X_MCASP0_REG_BASE,
-		.end 	= DAVINCI_DM646X_MCASP0_REG_BASE + (SZ_1K << 1) - 1,
-		.flags 	= IORESOURCE_MEM,
-	},
-	{
-		.name	= "tx",
-		.start	= DAVINCI_DM646X_DMA_MCASP0_AXEVT0,
-		.end	= DAVINCI_DM646X_DMA_MCASP0_AXEVT0,
-		.flags	= IORESOURCE_DMA,
-	},
-	{
-		.name	= "rx",
-		.start	= DAVINCI_DM646X_DMA_MCASP0_AREVT0,
-		.end	= DAVINCI_DM646X_DMA_MCASP0_AREVT0,
-		.flags	= IORESOURCE_DMA,
-	},
-	{
-		.name	= "tx",
-		.start	= DAVINCI_INTC_IRQ(IRQ_DM646X_MCASP0TXINT),
-		.flags	= IORESOURCE_IRQ,
-	},
-	{
-		.name	= "rx",
-		.start	= DAVINCI_INTC_IRQ(IRQ_DM646X_MCASP0RXINT),
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-/* DIT mode only, rx is not supported */
-static struct resource dm646x_mcasp1_resources[] = {
-	{
-		.name	= "mpu",
-		.start	= DAVINCI_DM646X_MCASP1_REG_BASE,
-		.end	= DAVINCI_DM646X_MCASP1_REG_BASE + (SZ_1K << 1) - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	{
-		.name	= "tx",
-		.start	= DAVINCI_DM646X_DMA_MCASP1_AXEVT1,
-		.end	= DAVINCI_DM646X_DMA_MCASP1_AXEVT1,
-		.flags	= IORESOURCE_DMA,
-	},
-	{
-		.name	= "tx",
-		.start	= DAVINCI_INTC_IRQ(IRQ_DM646X_MCASP1TXINT),
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device dm646x_mcasp0_device = {
-	.name		= "davinci-mcasp",
-	.id		= 0,
-	.num_resources	= ARRAY_SIZE(dm646x_mcasp0_resources),
-	.resource	= dm646x_mcasp0_resources,
-};
-
-static struct platform_device dm646x_mcasp1_device = {
-	.name		= "davinci-mcasp",
-	.id		= 1,
-	.num_resources	= ARRAY_SIZE(dm646x_mcasp1_resources),
-	.resource	= dm646x_mcasp1_resources,
-};
-
-static struct platform_device dm646x_dit_device = {
-	.name	= "spdif-dit",
-	.id	= -1,
-};
-
-static u64 vpif_dma_mask = DMA_BIT_MASK(32);
-
-static struct resource vpif_resource[] = {
-	{
-		.start	= DAVINCI_VPIF_BASE,
-		.end	= DAVINCI_VPIF_BASE + 0x03ff,
-		.flags	= IORESOURCE_MEM,
-	}
-};
-
-static struct platform_device vpif_dev = {
-	.name		= "vpif",
-	.id		= -1,
-	.dev		= {
-			.dma_mask 		= &vpif_dma_mask,
-			.coherent_dma_mask	= DMA_BIT_MASK(32),
-	},
-	.resource	= vpif_resource,
-	.num_resources	= ARRAY_SIZE(vpif_resource),
-};
-
-static struct resource vpif_display_resource[] = {
-	{
-		.start = DAVINCI_INTC_IRQ(IRQ_DM646X_VP_VERTINT2),
-		.end   = DAVINCI_INTC_IRQ(IRQ_DM646X_VP_VERTINT2),
-		.flags = IORESOURCE_IRQ,
-	},
-	{
-		.start = DAVINCI_INTC_IRQ(IRQ_DM646X_VP_VERTINT3),
-		.end   = DAVINCI_INTC_IRQ(IRQ_DM646X_VP_VERTINT3),
-		.flags = IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device vpif_display_dev = {
-	.name		= "vpif_display",
-	.id		= -1,
-	.dev		= {
-			.dma_mask 		= &vpif_dma_mask,
-			.coherent_dma_mask	= DMA_BIT_MASK(32),
-	},
-	.resource	= vpif_display_resource,
-	.num_resources	= ARRAY_SIZE(vpif_display_resource),
-};
-
-static struct resource vpif_capture_resource[] = {
-	{
-		.start = DAVINCI_INTC_IRQ(IRQ_DM646X_VP_VERTINT0),
-		.end   = DAVINCI_INTC_IRQ(IRQ_DM646X_VP_VERTINT0),
-		.flags = IORESOURCE_IRQ,
-	},
-	{
-		.start = DAVINCI_INTC_IRQ(IRQ_DM646X_VP_VERTINT1),
-		.end   = DAVINCI_INTC_IRQ(IRQ_DM646X_VP_VERTINT1),
-		.flags = IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device vpif_capture_dev = {
-	.name		= "vpif_capture",
-	.id		= -1,
-	.dev		= {
-			.dma_mask 		= &vpif_dma_mask,
-			.coherent_dma_mask	= DMA_BIT_MASK(32),
-	},
-	.resource	= vpif_capture_resource,
-	.num_resources	= ARRAY_SIZE(vpif_capture_resource),
-};
-
-static struct resource dm646x_gpio_resources[] = {
-	{	/* registers */
-		.start	= DAVINCI_GPIO_BASE,
-		.end	= DAVINCI_GPIO_BASE + SZ_4K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-	{	/* interrupt */
-		.start	= DAVINCI_INTC_IRQ(IRQ_DM646X_GPIOBNK0),
-		.end	= DAVINCI_INTC_IRQ(IRQ_DM646X_GPIOBNK0),
-		.flags	= IORESOURCE_IRQ,
-	},
-	{
-		.start	= DAVINCI_INTC_IRQ(IRQ_DM646X_GPIOBNK1),
-		.end	= DAVINCI_INTC_IRQ(IRQ_DM646X_GPIOBNK1),
-		.flags	= IORESOURCE_IRQ,
-	},
-	{
-		.start	= DAVINCI_INTC_IRQ(IRQ_DM646X_GPIOBNK2),
-		.end	= DAVINCI_INTC_IRQ(IRQ_DM646X_GPIOBNK2),
-		.flags	= IORESOURCE_IRQ,
-	},
-};
-
-static struct davinci_gpio_platform_data dm646x_gpio_platform_data = {
-	.no_auto_base	= true,
-	.base		= 0,
-	.ngpio		= 43,
-};
-
-int __init dm646x_gpio_register(void)
-{
-	return davinci_gpio_register(dm646x_gpio_resources,
-				     ARRAY_SIZE(dm646x_gpio_resources),
-				     &dm646x_gpio_platform_data);
-}
-/*----------------------------------------------------------------------*/
-
-static struct map_desc dm646x_io_desc[] = {
-	{
-		.virtual	= IO_VIRT,
-		.pfn		= __phys_to_pfn(IO_PHYS),
-		.length		= IO_SIZE,
-		.type		= MT_DEVICE
-	},
-};
-
-/* Contents of JTAG ID register used to identify exact cpu type */
-static struct davinci_id dm646x_ids[] = {
-	{
-		.variant	= 0x0,
-		.part_no	= 0xb770,
-		.manufacturer	= 0x017,
-		.cpu_id		= DAVINCI_CPU_ID_DM6467,
-		.name		= "dm6467_rev1.x",
-	},
-	{
-		.variant	= 0x1,
-		.part_no	= 0xb770,
-		.manufacturer	= 0x017,
-		.cpu_id		= DAVINCI_CPU_ID_DM6467,
-		.name		= "dm6467_rev3.x",
-	},
-};
-
-/*
- * Bottom half of timer0 is used for clockevent, top half is used for
- * clocksource.
- */
-static const struct davinci_timer_cfg dm646x_timer_cfg = {
-	.reg = DEFINE_RES_IO(DAVINCI_TIMER0_BASE, SZ_4K),
-	.irq = {
-		DEFINE_RES_IRQ(DAVINCI_INTC_IRQ(IRQ_TINT0_TINT12)),
-		DEFINE_RES_IRQ(DAVINCI_INTC_IRQ(IRQ_TINT0_TINT34)),
-	},
-};
-
-static struct plat_serial8250_port dm646x_serial0_platform_data[] = {
-	{
-		.mapbase	= DAVINCI_UART0_BASE,
-		.irq		= DAVINCI_INTC_IRQ(IRQ_UARTINT0),
-		.flags		= UPF_BOOT_AUTOCONF | UPF_SKIP_TEST |
-				  UPF_IOREMAP,
-		.iotype		= UPIO_MEM32,
-		.regshift	= 2,
-	},
-	{
-		.flags	= 0,
-	}
-};
-static struct plat_serial8250_port dm646x_serial1_platform_data[] = {
-	{
-		.mapbase	= DAVINCI_UART1_BASE,
-		.irq		= DAVINCI_INTC_IRQ(IRQ_UARTINT1),
-		.flags		= UPF_BOOT_AUTOCONF | UPF_SKIP_TEST |
-				  UPF_IOREMAP,
-		.iotype		= UPIO_MEM32,
-		.regshift	= 2,
-	},
-	{
-		.flags	= 0,
-	}
-};
-static struct plat_serial8250_port dm646x_serial2_platform_data[] = {
-	{
-		.mapbase	= DAVINCI_UART2_BASE,
-		.irq		= DAVINCI_INTC_IRQ(IRQ_DM646X_UARTINT2),
-		.flags		= UPF_BOOT_AUTOCONF | UPF_SKIP_TEST |
-				  UPF_IOREMAP,
-		.iotype		= UPIO_MEM32,
-		.regshift	= 2,
-	},
-	{
-		.flags	= 0,
-	}
-};
-
-struct platform_device dm646x_serial_device[] = {
-	{
-		.name			= "serial8250",
-		.id			= PLAT8250_DEV_PLATFORM,
-		.dev			= {
-			.platform_data	= dm646x_serial0_platform_data,
-		}
-	},
-	{
-		.name			= "serial8250",
-		.id			= PLAT8250_DEV_PLATFORM1,
-		.dev			= {
-			.platform_data	= dm646x_serial1_platform_data,
-		}
-	},
-	{
-		.name			= "serial8250",
-		.id			= PLAT8250_DEV_PLATFORM2,
-		.dev			= {
-			.platform_data	= dm646x_serial2_platform_data,
-		}
-	},
-	{
-	}
-};
-
-static const struct davinci_soc_info davinci_soc_info_dm646x = {
-	.io_desc		= dm646x_io_desc,
-	.io_desc_num		= ARRAY_SIZE(dm646x_io_desc),
-	.jtag_id_reg		= 0x01c40028,
-	.ids			= dm646x_ids,
-	.ids_num		= ARRAY_SIZE(dm646x_ids),
-	.pinmux_base		= DAVINCI_SYSTEM_MODULE_BASE,
-	.pinmux_pins		= dm646x_pins,
-	.pinmux_pins_num	= ARRAY_SIZE(dm646x_pins),
-	.emac_pdata		= &dm646x_emac_pdata,
-	.sram_dma		= 0x10010000,
-	.sram_len		= SZ_32K,
-};
-
-void __init dm646x_init_mcasp0(struct snd_platform_data *pdata)
-{
-	dm646x_mcasp0_device.dev.platform_data = pdata;
-	platform_device_register(&dm646x_mcasp0_device);
-}
-
-void __init dm646x_init_mcasp1(struct snd_platform_data *pdata)
-{
-	dm646x_mcasp1_device.dev.platform_data = pdata;
-	platform_device_register(&dm646x_mcasp1_device);
-	platform_device_register(&dm646x_dit_device);
-}
-
-void dm646x_setup_vpif(struct vpif_display_config *display_config,
-		       struct vpif_capture_config *capture_config)
-{
-	unsigned int value;
-
-	value = __raw_readl(DAVINCI_SYSMOD_VIRT(SYSMOD_VSCLKDIS));
-	value &= ~VSCLKDIS_MASK;
-	__raw_writel(value, DAVINCI_SYSMOD_VIRT(SYSMOD_VSCLKDIS));
-
-	value = __raw_readl(DAVINCI_SYSMOD_VIRT(SYSMOD_VDD3P3VPWDN));
-	value &= ~VDD3P3V_VID_MASK;
-	__raw_writel(value, DAVINCI_SYSMOD_VIRT(SYSMOD_VDD3P3VPWDN));
-
-	davinci_cfg_reg(DM646X_STSOMUX_DISABLE);
-	davinci_cfg_reg(DM646X_STSIMUX_DISABLE);
-	davinci_cfg_reg(DM646X_PTSOMUX_DISABLE);
-	davinci_cfg_reg(DM646X_PTSIMUX_DISABLE);
-
-	vpif_display_dev.dev.platform_data = display_config;
-	vpif_capture_dev.dev.platform_data = capture_config;
-	platform_device_register(&vpif_dev);
-	platform_device_register(&vpif_display_dev);
-	platform_device_register(&vpif_capture_dev);
-}
-
-int __init dm646x_init_edma(struct edma_rsv_info *rsv)
-{
-	struct platform_device *edma_pdev;
-
-	dm646x_edma_pdata.rsv = rsv;
-
-	edma_pdev = platform_device_register_full(&dm646x_edma_device);
-	return PTR_ERR_OR_ZERO(edma_pdev);
-}
-
-void __init dm646x_init(void)
-{
-	davinci_common_init(&davinci_soc_info_dm646x);
-	davinci_map_sysmod();
-}
-
-void __init dm646x_init_time(unsigned long ref_clk_rate,
-			     unsigned long aux_clkin_rate)
-{
-	void __iomem *pll1, *psc;
-	struct clk *clk;
-	int rv;
-
-	clk_register_fixed_rate(NULL, "ref_clk", NULL, 0, ref_clk_rate);
-	clk_register_fixed_rate(NULL, "aux_clkin", NULL, 0, aux_clkin_rate);
-
-	pll1 = ioremap(DAVINCI_PLL1_BASE, SZ_1K);
-	dm646x_pll1_init(NULL, pll1, NULL);
-
-	psc = ioremap(DAVINCI_PWR_SLEEP_CNTRL_BASE, SZ_4K);
-	dm646x_psc_init(NULL, psc);
-
-	clk = clk_get(NULL, "timer0");
-	if (WARN_ON(IS_ERR(clk))) {
-		pr_err("Unable to get the timer clock\n");
-		return;
-	}
-
-	rv = davinci_timer_register(clk, &dm646x_timer_cfg);
-	WARN(rv, "Unable to register the timer: %d\n", rv);
-}
-
-static struct resource dm646x_pll2_resources[] = {
-	{
-		.start	= DAVINCI_PLL2_BASE,
-		.end	= DAVINCI_PLL2_BASE + SZ_1K - 1,
-		.flags	= IORESOURCE_MEM,
-	},
-};
-
-static struct platform_device dm646x_pll2_device = {
-	.name		= "dm646x-pll2",
-	.id		= -1,
-	.resource	= dm646x_pll2_resources,
-	.num_resources	= ARRAY_SIZE(dm646x_pll2_resources),
-};
-
-void __init dm646x_register_clocks(void)
-{
-	/* PLL1 and PSC are registered in dm646x_init_time() */
-	platform_device_register(&dm646x_pll2_device);
-}
-
-static const struct davinci_aintc_config dm646x_aintc_config = {
-	.reg = {
-		.start		= DAVINCI_ARM_INTC_BASE,
-		.end		= DAVINCI_ARM_INTC_BASE + SZ_4K - 1,
-		.flags		= IORESOURCE_MEM,
-	},
-	.num_irqs		= 64,
-	.prios			= dm646x_default_priorities,
-};
-
-void __init dm646x_init_irq(void)
-{
-	davinci_aintc_init(&dm646x_aintc_config);
-}
-
-static int __init dm646x_init_devices(void)
-{
-	int ret = 0;
-
-	if (!cpu_is_davinci_dm646x())
-		return 0;
-
-	platform_device_register(&dm646x_mdio_device);
-	platform_device_register(&dm646x_emac_device);
-
-	ret = davinci_init_wdt();
-	if (ret)
-		pr_warn("%s: watchdog init failed: %d\n", __func__, ret);
-
-	return ret;
-}
-postcore_initcall(dm646x_init_devices);
diff --git a/arch/arm/mach-davinci/hardware.h b/arch/arm/mach-davinci/hardware.h
new file mode 100644
index 000000000000..7848b6a240b4
--- /dev/null
+++ b/arch/arm/mach-davinci/hardware.h
@@ -0,0 +1,31 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Hardware definitions common to all DaVinci family processors
+ *
+ * Author: Kevin Hilman, Deep Root Systems, LLC
+ *
+ * 2007 (c) Deep Root Systems, LLC.
+ */
+#ifndef __ASM_ARCH_HARDWARE_H
+#define __ASM_ARCH_HARDWARE_H
+
+/*
+ * Before you add anything to ths file:
+ *
+ * This header is for defines common to ALL DaVinci family chips.
+ * Anything that is chip specific should go in <chipname>.h,
+ * and the chip/board init code should then explicitly include
+ * <chipname>.h
+ */
+/*
+ * I/O mapping
+ */
+#define IO_PHYS				UL(0x01c00000)
+#define IO_OFFSET			0xfd000000 /* Virtual IO = 0xfec00000 */
+#define IO_SIZE				0x00400000
+#define IO_VIRT				(IO_PHYS + IO_OFFSET)
+#define io_v2p(va)			((va) - IO_OFFSET)
+#define __IO_ADDRESS(x)			((x) + IO_OFFSET)
+#define IO_ADDRESS(pa)			IOMEM(__IO_ADDRESS(pa))
+
+#endif /* __ASM_ARCH_HARDWARE_H */
diff --git a/arch/arm/mach-davinci/include/mach/common.h b/arch/arm/mach-davinci/include/mach/common.h
deleted file mode 100644
index 139b83de011d..000000000000
--- a/arch/arm/mach-davinci/include/mach/common.h
+++ /dev/null
@@ -1,79 +0,0 @@
-/*
- * Header for code common to all DaVinci machines.
- *
- * Author: Kevin Hilman, MontaVista Software, Inc. <source@mvista.com>
- *
- * 2007 (c) MontaVista Software, Inc. This file is licensed under
- * the terms of the GNU General Public License version 2. This program
- * is licensed "as is" without any warranty of any kind, whether express
- * or implied.
- */
-
-#ifndef __ARCH_ARM_MACH_DAVINCI_COMMON_H
-#define __ARCH_ARM_MACH_DAVINCI_COMMON_H
-
-#include <linux/clk.h>
-#include <linux/compiler.h>
-#include <linux/types.h>
-#include <linux/reboot.h>
-
-#include <asm/irq.h>
-
-#define DAVINCI_INTC_START		NR_IRQS
-#define DAVINCI_INTC_IRQ(_irqnum)	(DAVINCI_INTC_START + (_irqnum))
-
-struct davinci_gpio_controller;
-
-/*
- * SoC info passed into common davinci modules.
- *
- * Base addresses in this structure should be physical and not virtual.
- * Modules that take such base addresses, should internally ioremap() them to
- * use.
- */
-struct davinci_soc_info {
-	struct map_desc			*io_desc;
-	unsigned long			io_desc_num;
-	u32				cpu_id;
-	u32				jtag_id;
-	u32				jtag_id_reg;
-	struct davinci_id		*ids;
-	unsigned long			ids_num;
-	u32				pinmux_base;
-	const struct mux_config		*pinmux_pins;
-	unsigned long			pinmux_pins_num;
-	int				gpio_type;
-	u32				gpio_base;
-	unsigned			gpio_num;
-	unsigned			gpio_irq;
-	unsigned			gpio_unbanked;
-	struct davinci_gpio_controller	*gpio_ctlrs;
-	int				gpio_ctlrs_num;
-	struct emac_platform_data	*emac_pdata;
-	dma_addr_t			sram_dma;
-	unsigned			sram_len;
-};
-
-extern struct davinci_soc_info davinci_soc_info;
-
-extern void davinci_common_init(const struct davinci_soc_info *soc_info);
-extern void davinci_init_ide(void);
-void davinci_init_late(void);
-
-#ifdef CONFIG_CPU_FREQ
-int davinci_cpufreq_init(void);
-#else
-static inline int davinci_cpufreq_init(void) { return 0; }
-#endif
-
-#ifdef CONFIG_SUSPEND
-int davinci_pm_init(void);
-#else
-static inline int davinci_pm_init(void) { return 0; }
-#endif
-
-void __init pdata_quirks_init(void);
-
-#define SRAM_SIZE	SZ_128K
-
-#endif /* __ARCH_ARM_MACH_DAVINCI_COMMON_H */
diff --git a/arch/arm/mach-davinci/include/mach/cputype.h b/arch/arm/mach-davinci/include/mach/cputype.h
deleted file mode 100644
index 1fc84e21664d..000000000000
--- a/arch/arm/mach-davinci/include/mach/cputype.h
+++ /dev/null
@@ -1,86 +0,0 @@
-/*
- * DaVinci CPU type detection
- *
- * Author: Kevin Hilman, Deep Root Systems, LLC
- *
- * Defines the cpu_is_*() macros for runtime detection of DaVinci
- * device type.  In addition, if support for a given device is not
- * compiled in to the kernel, the macros return 0 so that
- * resulting code can be optimized out.
- *
- * 2009 (c) Deep Root Systems, LLC. This file is licensed under
- * the terms of the GNU General Public License version 2. This program
- * is licensed "as is" without any warranty of any kind, whether express
- * or implied.
- */
-#ifndef _ASM_ARCH_CPU_H
-#define _ASM_ARCH_CPU_H
-
-#include <mach/common.h>
-
-struct davinci_id {
-	u8	variant;	/* JTAG ID bits 31:28 */
-	u16	part_no;	/* JTAG ID bits 27:12 */
-	u16	manufacturer;	/* JTAG ID bits 11:1 */
-	u32	cpu_id;
-	char	*name;
-};
-
-/* Can use lower 16 bits of cpu id  for a variant when required */
-#define	DAVINCI_CPU_ID_DM6446		0x64460000
-#define	DAVINCI_CPU_ID_DM6467		0x64670000
-#define	DAVINCI_CPU_ID_DM355		0x03550000
-#define	DAVINCI_CPU_ID_DM365		0x03650000
-#define	DAVINCI_CPU_ID_DA830		0x08300000
-#define	DAVINCI_CPU_ID_DA850		0x08500000
-
-#define IS_DAVINCI_CPU(type, id)					\
-static inline int is_davinci_ ##type(void)				\
-{									\
-	return (davinci_soc_info.cpu_id == (id));			\
-}
-
-IS_DAVINCI_CPU(dm644x, DAVINCI_CPU_ID_DM6446)
-IS_DAVINCI_CPU(dm646x, DAVINCI_CPU_ID_DM6467)
-IS_DAVINCI_CPU(dm355, DAVINCI_CPU_ID_DM355)
-IS_DAVINCI_CPU(dm365, DAVINCI_CPU_ID_DM365)
-IS_DAVINCI_CPU(da830, DAVINCI_CPU_ID_DA830)
-IS_DAVINCI_CPU(da850, DAVINCI_CPU_ID_DA850)
-
-#ifdef CONFIG_ARCH_DAVINCI_DM644x
-#define cpu_is_davinci_dm644x() is_davinci_dm644x()
-#else
-#define cpu_is_davinci_dm644x() 0
-#endif
-
-#ifdef CONFIG_ARCH_DAVINCI_DM646x
-#define cpu_is_davinci_dm646x() is_davinci_dm646x()
-#else
-#define cpu_is_davinci_dm646x() 0
-#endif
-
-#ifdef CONFIG_ARCH_DAVINCI_DM355
-#define cpu_is_davinci_dm355() is_davinci_dm355()
-#else
-#define cpu_is_davinci_dm355() 0
-#endif
-
-#ifdef CONFIG_ARCH_DAVINCI_DM365
-#define cpu_is_davinci_dm365() is_davinci_dm365()
-#else
-#define cpu_is_davinci_dm365() 0
-#endif
-
-#ifdef CONFIG_ARCH_DAVINCI_DA830
-#define cpu_is_davinci_da830() is_davinci_da830()
-#else
-#define cpu_is_davinci_da830() 0
-#endif
-
-#ifdef CONFIG_ARCH_DAVINCI_DA850
-#define cpu_is_davinci_da850() is_davinci_da850()
-#else
-#define cpu_is_davinci_da850() 0
-#endif
-
-#endif
diff --git a/arch/arm/mach-davinci/include/mach/hardware.h b/arch/arm/mach-davinci/include/mach/hardware.h
deleted file mode 100644
index 16bb42291d39..000000000000
--- a/arch/arm/mach-davinci/include/mach/hardware.h
+++ /dev/null
@@ -1,33 +0,0 @@
-/*
- * Hardware definitions common to all DaVinci family processors
- *
- * Author: Kevin Hilman, Deep Root Systems, LLC
- *
- * 2007 (c) Deep Root Systems, LLC. This file is licensed under
- * the terms of the GNU General Public License version 2. This program
- * is licensed "as is" without any warranty of any kind, whether express
- * or implied.
- */
-#ifndef __ASM_ARCH_HARDWARE_H
-#define __ASM_ARCH_HARDWARE_H
-
-/*
- * Before you add anything to ths file:
- *
- * This header is for defines common to ALL DaVinci family chips.
- * Anything that is chip specific should go in <chipname>.h,
- * and the chip/board init code should then explicitly include
- * <chipname>.h
- */
-/*
- * I/O mapping
- */
-#define IO_PHYS				UL(0x01c00000)
-#define IO_OFFSET			0xfd000000 /* Virtual IO = 0xfec00000 */
-#define IO_SIZE				0x00400000
-#define IO_VIRT				(IO_PHYS + IO_OFFSET)
-#define io_v2p(va)			((va) - IO_OFFSET)
-#define __IO_ADDRESS(x)			((x) + IO_OFFSET)
-#define IO_ADDRESS(pa)			IOMEM(__IO_ADDRESS(pa))
-
-#endif /* __ASM_ARCH_HARDWARE_H */
diff --git a/arch/arm/mach-davinci/include/mach/mux.h b/arch/arm/mach-davinci/include/mach/mux.h
deleted file mode 100644
index 631655e68ae0..000000000000
--- a/arch/arm/mach-davinci/include/mach/mux.h
+++ /dev/null
@@ -1,990 +0,0 @@
-/*
- * Table of the DAVINCI register configurations for the PINMUX combinations
- *
- * Author: Vladimir Barinov, MontaVista Software, Inc. <source@mvista.com>
- *
- * Based on linux/include/asm-arm/arch-omap/mux.h:
- * Copyright (C) 2003 - 2005 Nokia Corporation
- *
- * Written by Tony Lindgren
- *
- * 2007 (c) MontaVista Software, Inc. This file is licensed under
- * the terms of the GNU General Public License version 2. This program
- * is licensed "as is" without any warranty of any kind, whether express
- * or implied.
- *
- * Copyright (C) 2008 Texas Instruments.
- */
-
-#ifndef __INC_MACH_MUX_H
-#define __INC_MACH_MUX_H
-
-struct mux_config {
-	const char *name;
-	const char *mux_reg_name;
-	const unsigned char mux_reg;
-	const unsigned char mask_offset;
-	const unsigned char mask;
-	const unsigned char mode;
-	bool debug;
-};
-
-enum davinci_dm644x_index {
-	/* ATA and HDDIR functions */
-	DM644X_HDIREN,
-	DM644X_ATAEN,
-	DM644X_ATAEN_DISABLE,
-
-	/* HPI functions */
-	DM644X_HPIEN_DISABLE,
-
-	/* AEAW functions */
-	DM644X_AEAW,
-	DM644X_AEAW0,
-	DM644X_AEAW1,
-	DM644X_AEAW2,
-	DM644X_AEAW3,
-	DM644X_AEAW4,
-
-	/* Memory Stick */
-	DM644X_MSTK,
-
-	/* I2C */
-	DM644X_I2C,
-
-	/* ASP function */
-	DM644X_MCBSP,
-
-	/* UART1 */
-	DM644X_UART1,
-
-	/* UART2 */
-	DM644X_UART2,
-
-	/* PWM0 */
-	DM644X_PWM0,
-
-	/* PWM1 */
-	DM644X_PWM1,
-
-	/* PWM2 */
-	DM644X_PWM2,
-
-	/* VLYNQ function */
-	DM644X_VLYNQEN,
-	DM644X_VLSCREN,
-	DM644X_VLYNQWD,
-
-	/* EMAC and MDIO function */
-	DM644X_EMACEN,
-
-	/* GPIO3V[0:16] pins */
-	DM644X_GPIO3V,
-
-	/* GPIO pins */
-	DM644X_GPIO0,
-	DM644X_GPIO3,
-	DM644X_GPIO43_44,
-	DM644X_GPIO46_47,
-
-	/* VPBE */
-	DM644X_RGB666,
-
-	/* LCD */
-	DM644X_LOEEN,
-	DM644X_LFLDEN,
-};
-
-enum davinci_dm646x_index {
-	/* ATA function */
-	DM646X_ATAEN,
-
-	/* AUDIO Clock */
-	DM646X_AUDCK1,
-	DM646X_AUDCK0,
-
-	/* CRGEN Control */
-	DM646X_CRGMUX,
-
-	/* VPIF Control */
-	DM646X_STSOMUX_DISABLE,
-	DM646X_STSIMUX_DISABLE,
-	DM646X_PTSOMUX_DISABLE,
-	DM646X_PTSIMUX_DISABLE,
-
-	/* TSIF Control */
-	DM646X_STSOMUX,
-	DM646X_STSIMUX,
-	DM646X_PTSOMUX_PARALLEL,
-	DM646X_PTSIMUX_PARALLEL,
-	DM646X_PTSOMUX_SERIAL,
-	DM646X_PTSIMUX_SERIAL,
-};
-
-enum davinci_dm355_index {
-	/* MMC/SD 0 */
-	DM355_MMCSD0,
-
-	/* MMC/SD 1 */
-	DM355_SD1_CLK,
-	DM355_SD1_CMD,
-	DM355_SD1_DATA3,
-	DM355_SD1_DATA2,
-	DM355_SD1_DATA1,
-	DM355_SD1_DATA0,
-
-	/* I2C */
-	DM355_I2C_SDA,
-	DM355_I2C_SCL,
-
-	/* ASP0 function */
-	DM355_MCBSP0_BDX,
-	DM355_MCBSP0_X,
-	DM355_MCBSP0_BFSX,
-	DM355_MCBSP0_BDR,
-	DM355_MCBSP0_R,
-	DM355_MCBSP0_BFSR,
-
-	/* SPI0 */
-	DM355_SPI0_SDI,
-	DM355_SPI0_SDENA0,
-	DM355_SPI0_SDENA1,
-
-	/* IRQ muxing */
-	DM355_INT_EDMA_CC,
-	DM355_INT_EDMA_TC0_ERR,
-	DM355_INT_EDMA_TC1_ERR,
-
-	/* EDMA event muxing */
-	DM355_EVT8_ASP1_TX,
-	DM355_EVT9_ASP1_RX,
-	DM355_EVT26_MMC0_RX,
-
-	/* Video Out */
-	DM355_VOUT_FIELD,
-	DM355_VOUT_FIELD_G70,
-	DM355_VOUT_HVSYNC,
-	DM355_VOUT_COUTL_EN,
-	DM355_VOUT_COUTH_EN,
-
-	/* Video In Pin Mux */
-	DM355_VIN_PCLK,
-	DM355_VIN_CAM_WEN,
-	DM355_VIN_CAM_VD,
-	DM355_VIN_CAM_HD,
-	DM355_VIN_YIN_EN,
-	DM355_VIN_CINL_EN,
-	DM355_VIN_CINH_EN,
-};
-
-enum davinci_dm365_index {
-	/* MMC/SD 0 */
-	DM365_MMCSD0,
-
-	/* MMC/SD 1 */
-	DM365_SD1_CLK,
-	DM365_SD1_CMD,
-	DM365_SD1_DATA3,
-	DM365_SD1_DATA2,
-	DM365_SD1_DATA1,
-	DM365_SD1_DATA0,
-
-	/* I2C */
-	DM365_I2C_SDA,
-	DM365_I2C_SCL,
-
-	/* AEMIF */
-	DM365_AEMIF_AR_A14,
-	DM365_AEMIF_AR_BA0,
-	DM365_AEMIF_A3,
-	DM365_AEMIF_A7,
-	DM365_AEMIF_D15_8,
-	DM365_AEMIF_CE0,
-	DM365_AEMIF_CE1,
-	DM365_AEMIF_WE_OE,
-
-	/* ASP0 function */
-	DM365_MCBSP0_BDX,
-	DM365_MCBSP0_X,
-	DM365_MCBSP0_BFSX,
-	DM365_MCBSP0_BDR,
-	DM365_MCBSP0_R,
-	DM365_MCBSP0_BFSR,
-
-	/* SPI0 */
-	DM365_SPI0_SCLK,
-	DM365_SPI0_SDI,
-	DM365_SPI0_SDO,
-	DM365_SPI0_SDENA0,
-	DM365_SPI0_SDENA1,
-
-	/* UART */
-	DM365_UART0_RXD,
-	DM365_UART0_TXD,
-	DM365_UART1_RXD,
-	DM365_UART1_TXD,
-	DM365_UART1_RTS,
-	DM365_UART1_CTS,
-
-	/* EMAC */
-	DM365_EMAC_TX_EN,
-	DM365_EMAC_TX_CLK,
-	DM365_EMAC_COL,
-	DM365_EMAC_TXD3,
-	DM365_EMAC_TXD2,
-	DM365_EMAC_TXD1,
-	DM365_EMAC_TXD0,
-	DM365_EMAC_RXD3,
-	DM365_EMAC_RXD2,
-	DM365_EMAC_RXD1,
-	DM365_EMAC_RXD0,
-	DM365_EMAC_RX_CLK,
-	DM365_EMAC_RX_DV,
-	DM365_EMAC_RX_ER,
-	DM365_EMAC_CRS,
-	DM365_EMAC_MDIO,
-	DM365_EMAC_MDCLK,
-
-	/* Key Scan */
-	DM365_KEYSCAN,
-
-	/* PWM */
-	DM365_PWM0,
-	DM365_PWM0_G23,
-	DM365_PWM1,
-	DM365_PWM1_G25,
-	DM365_PWM2_G87,
-	DM365_PWM2_G88,
-	DM365_PWM2_G89,
-	DM365_PWM2_G90,
-	DM365_PWM3_G80,
-	DM365_PWM3_G81,
-	DM365_PWM3_G85,
-	DM365_PWM3_G86,
-
-	/* SPI1 */
-	DM365_SPI1_SCLK,
-	DM365_SPI1_SDO,
-	DM365_SPI1_SDI,
-	DM365_SPI1_SDENA0,
-	DM365_SPI1_SDENA1,
-
-	/* SPI2 */
-	DM365_SPI2_SCLK,
-	DM365_SPI2_SDO,
-	DM365_SPI2_SDI,
-	DM365_SPI2_SDENA0,
-	DM365_SPI2_SDENA1,
-
-	/* SPI3 */
-	DM365_SPI3_SCLK,
-	DM365_SPI3_SDO,
-	DM365_SPI3_SDI,
-	DM365_SPI3_SDENA0,
-	DM365_SPI3_SDENA1,
-
-	/* SPI4 */
-	DM365_SPI4_SCLK,
-	DM365_SPI4_SDO,
-	DM365_SPI4_SDI,
-	DM365_SPI4_SDENA0,
-	DM365_SPI4_SDENA1,
-
-	/* Clock */
-	DM365_CLKOUT0,
-	DM365_CLKOUT1,
-	DM365_CLKOUT2,
-
-	/* GPIO */
-	DM365_GPIO20,
-	DM365_GPIO30,
-	DM365_GPIO31,
-	DM365_GPIO32,
-	DM365_GPIO33,
-	DM365_GPIO40,
-	DM365_GPIO64_57,
-
-	/* Video */
-	DM365_VOUT_FIELD,
-	DM365_VOUT_FIELD_G81,
-	DM365_VOUT_HVSYNC,
-	DM365_VOUT_COUTL_EN,
-	DM365_VOUT_COUTH_EN,
-	DM365_VIN_CAM_WEN,
-	DM365_VIN_CAM_VD,
-	DM365_VIN_CAM_HD,
-	DM365_VIN_YIN4_7_EN,
-	DM365_VIN_YIN0_3_EN,
-
-	/* IRQ muxing */
-	DM365_INT_EDMA_CC,
-	DM365_INT_EDMA_TC0_ERR,
-	DM365_INT_EDMA_TC1_ERR,
-	DM365_INT_EDMA_TC2_ERR,
-	DM365_INT_EDMA_TC3_ERR,
-	DM365_INT_PRTCSS,
-	DM365_INT_EMAC_RXTHRESH,
-	DM365_INT_EMAC_RXPULSE,
-	DM365_INT_EMAC_TXPULSE,
-	DM365_INT_EMAC_MISCPULSE,
-	DM365_INT_IMX0_ENABLE,
-	DM365_INT_IMX0_DISABLE,
-	DM365_INT_HDVICP_ENABLE,
-	DM365_INT_HDVICP_DISABLE,
-	DM365_INT_IMX1_ENABLE,
-	DM365_INT_IMX1_DISABLE,
-	DM365_INT_NSF_ENABLE,
-	DM365_INT_NSF_DISABLE,
-
-	/* EDMA event muxing */
-	DM365_EVT2_ASP_TX,
-	DM365_EVT3_ASP_RX,
-	DM365_EVT2_VC_TX,
-	DM365_EVT3_VC_RX,
-	DM365_EVT26_MMC0_RX,
-};
-
-enum da830_index {
-	DA830_GPIO7_14,
-	DA830_RTCK,
-	DA830_GPIO7_15,
-	DA830_EMU_0,
-	DA830_EMB_SDCKE,
-	DA830_EMB_CLK_GLUE,
-	DA830_EMB_CLK,
-	DA830_NEMB_CS_0,
-	DA830_NEMB_CAS,
-	DA830_NEMB_RAS,
-	DA830_NEMB_WE,
-	DA830_EMB_BA_1,
-	DA830_EMB_BA_0,
-	DA830_EMB_A_0,
-	DA830_EMB_A_1,
-	DA830_EMB_A_2,
-	DA830_EMB_A_3,
-	DA830_EMB_A_4,
-	DA830_EMB_A_5,
-	DA830_GPIO7_0,
-	DA830_GPIO7_1,
-	DA830_GPIO7_2,
-	DA830_GPIO7_3,
-	DA830_GPIO7_4,
-	DA830_GPIO7_5,
-	DA830_GPIO7_6,
-	DA830_GPIO7_7,
-	DA830_EMB_A_6,
-	DA830_EMB_A_7,
-	DA830_EMB_A_8,
-	DA830_EMB_A_9,
-	DA830_EMB_A_10,
-	DA830_EMB_A_11,
-	DA830_EMB_A_12,
-	DA830_EMB_D_31,
-	DA830_GPIO7_8,
-	DA830_GPIO7_9,
-	DA830_GPIO7_10,
-	DA830_GPIO7_11,
-	DA830_GPIO7_12,
-	DA830_GPIO7_13,
-	DA830_GPIO3_13,
-	DA830_EMB_D_30,
-	DA830_EMB_D_29,
-	DA830_EMB_D_28,
-	DA830_EMB_D_27,
-	DA830_EMB_D_26,
-	DA830_EMB_D_25,
-	DA830_EMB_D_24,
-	DA830_EMB_D_23,
-	DA830_EMB_D_22,
-	DA830_EMB_D_21,
-	DA830_EMB_D_20,
-	DA830_EMB_D_19,
-	DA830_EMB_D_18,
-	DA830_EMB_D_17,
-	DA830_EMB_D_16,
-	DA830_NEMB_WE_DQM_3,
-	DA830_NEMB_WE_DQM_2,
-	DA830_EMB_D_0,
-	DA830_EMB_D_1,
-	DA830_EMB_D_2,
-	DA830_EMB_D_3,
-	DA830_EMB_D_4,
-	DA830_EMB_D_5,
-	DA830_EMB_D_6,
-	DA830_GPIO6_0,
-	DA830_GPIO6_1,
-	DA830_GPIO6_2,
-	DA830_GPIO6_3,
-	DA830_GPIO6_4,
-	DA830_GPIO6_5,
-	DA830_GPIO6_6,
-	DA830_EMB_D_7,
-	DA830_EMB_D_8,
-	DA830_EMB_D_9,
-	DA830_EMB_D_10,
-	DA830_EMB_D_11,
-	DA830_EMB_D_12,
-	DA830_EMB_D_13,
-	DA830_EMB_D_14,
-	DA830_GPIO6_7,
-	DA830_GPIO6_8,
-	DA830_GPIO6_9,
-	DA830_GPIO6_10,
-	DA830_GPIO6_11,
-	DA830_GPIO6_12,
-	DA830_GPIO6_13,
-	DA830_GPIO6_14,
-	DA830_EMB_D_15,
-	DA830_NEMB_WE_DQM_1,
-	DA830_NEMB_WE_DQM_0,
-	DA830_SPI0_SOMI_0,
-	DA830_SPI0_SIMO_0,
-	DA830_SPI0_CLK,
-	DA830_NSPI0_ENA,
-	DA830_NSPI0_SCS_0,
-	DA830_EQEP0I,
-	DA830_EQEP0S,
-	DA830_EQEP1I,
-	DA830_NUART0_CTS,
-	DA830_NUART0_RTS,
-	DA830_EQEP0A,
-	DA830_EQEP0B,
-	DA830_GPIO6_15,
-	DA830_GPIO5_14,
-	DA830_GPIO5_15,
-	DA830_GPIO5_0,
-	DA830_GPIO5_1,
-	DA830_GPIO5_2,
-	DA830_GPIO5_3,
-	DA830_GPIO5_4,
-	DA830_SPI1_SOMI_0,
-	DA830_SPI1_SIMO_0,
-	DA830_SPI1_CLK,
-	DA830_UART0_RXD,
-	DA830_UART0_TXD,
-	DA830_AXR1_10,
-	DA830_AXR1_11,
-	DA830_NSPI1_ENA,
-	DA830_I2C1_SCL,
-	DA830_I2C1_SDA,
-	DA830_EQEP1S,
-	DA830_I2C0_SDA,
-	DA830_I2C0_SCL,
-	DA830_UART2_RXD,
-	DA830_TM64P0_IN12,
-	DA830_TM64P0_OUT12,
-	DA830_GPIO5_5,
-	DA830_GPIO5_6,
-	DA830_GPIO5_7,
-	DA830_GPIO5_8,
-	DA830_GPIO5_9,
-	DA830_GPIO5_10,
-	DA830_GPIO5_11,
-	DA830_GPIO5_12,
-	DA830_NSPI1_SCS_0,
-	DA830_USB0_DRVVBUS,
-	DA830_AHCLKX0,
-	DA830_ACLKX0,
-	DA830_AFSX0,
-	DA830_AHCLKR0,
-	DA830_ACLKR0,
-	DA830_AFSR0,
-	DA830_UART2_TXD,
-	DA830_AHCLKX2,
-	DA830_ECAP0_APWM0,
-	DA830_RMII_MHZ_50_CLK,
-	DA830_ECAP1_APWM1,
-	DA830_USB_REFCLKIN,
-	DA830_GPIO5_13,
-	DA830_GPIO4_15,
-	DA830_GPIO2_11,
-	DA830_GPIO2_12,
-	DA830_GPIO2_13,
-	DA830_GPIO2_14,
-	DA830_GPIO2_15,
-	DA830_GPIO3_12,
-	DA830_AMUTE0,
-	DA830_AXR0_0,
-	DA830_AXR0_1,
-	DA830_AXR0_2,
-	DA830_AXR0_3,
-	DA830_AXR0_4,
-	DA830_AXR0_5,
-	DA830_AXR0_6,
-	DA830_RMII_TXD_0,
-	DA830_RMII_TXD_1,
-	DA830_RMII_TXEN,
-	DA830_RMII_CRS_DV,
-	DA830_RMII_RXD_0,
-	DA830_RMII_RXD_1,
-	DA830_RMII_RXER,
-	DA830_AFSR2,
-	DA830_ACLKX2,
-	DA830_AXR2_3,
-	DA830_AXR2_2,
-	DA830_AXR2_1,
-	DA830_AFSX2,
-	DA830_ACLKR2,
-	DA830_NRESETOUT,
-	DA830_GPIO3_0,
-	DA830_GPIO3_1,
-	DA830_GPIO3_2,
-	DA830_GPIO3_3,
-	DA830_GPIO3_4,
-	DA830_GPIO3_5,
-	DA830_GPIO3_6,
-	DA830_AXR0_7,
-	DA830_AXR0_8,
-	DA830_UART1_RXD,
-	DA830_UART1_TXD,
-	DA830_AXR0_11,
-	DA830_AHCLKX1,
-	DA830_ACLKX1,
-	DA830_AFSX1,
-	DA830_MDIO_CLK,
-	DA830_MDIO_D,
-	DA830_AXR0_9,
-	DA830_AXR0_10,
-	DA830_EPWM0B,
-	DA830_EPWM0A,
-	DA830_EPWMSYNCI,
-	DA830_AXR2_0,
-	DA830_EPWMSYNC0,
-	DA830_GPIO3_7,
-	DA830_GPIO3_8,
-	DA830_GPIO3_9,
-	DA830_GPIO3_10,
-	DA830_GPIO3_11,
-	DA830_GPIO3_14,
-	DA830_GPIO3_15,
-	DA830_GPIO4_10,
-	DA830_AHCLKR1,
-	DA830_ACLKR1,
-	DA830_AFSR1,
-	DA830_AMUTE1,
-	DA830_AXR1_0,
-	DA830_AXR1_1,
-	DA830_AXR1_2,
-	DA830_AXR1_3,
-	DA830_ECAP2_APWM2,
-	DA830_EHRPWMGLUETZ,
-	DA830_EQEP1A,
-	DA830_GPIO4_11,
-	DA830_GPIO4_12,
-	DA830_GPIO4_13,
-	DA830_GPIO4_14,
-	DA830_GPIO4_0,
-	DA830_GPIO4_1,
-	DA830_GPIO4_2,
-	DA830_GPIO4_3,
-	DA830_AXR1_4,
-	DA830_AXR1_5,
-	DA830_AXR1_6,
-	DA830_AXR1_7,
-	DA830_AXR1_8,
-	DA830_AXR1_9,
-	DA830_EMA_D_0,
-	DA830_EMA_D_1,
-	DA830_EQEP1B,
-	DA830_EPWM2B,
-	DA830_EPWM2A,
-	DA830_EPWM1B,
-	DA830_EPWM1A,
-	DA830_MMCSD_DAT_0,
-	DA830_MMCSD_DAT_1,
-	DA830_UHPI_HD_0,
-	DA830_UHPI_HD_1,
-	DA830_GPIO4_4,
-	DA830_GPIO4_5,
-	DA830_GPIO4_6,
-	DA830_GPIO4_7,
-	DA830_GPIO4_8,
-	DA830_GPIO4_9,
-	DA830_GPIO0_0,
-	DA830_GPIO0_1,
-	DA830_EMA_D_2,
-	DA830_EMA_D_3,
-	DA830_EMA_D_4,
-	DA830_EMA_D_5,
-	DA830_EMA_D_6,
-	DA830_EMA_D_7,
-	DA830_EMA_D_8,
-	DA830_EMA_D_9,
-	DA830_MMCSD_DAT_2,
-	DA830_MMCSD_DAT_3,
-	DA830_MMCSD_DAT_4,
-	DA830_MMCSD_DAT_5,
-	DA830_MMCSD_DAT_6,
-	DA830_MMCSD_DAT_7,
-	DA830_UHPI_HD_8,
-	DA830_UHPI_HD_9,
-	DA830_UHPI_HD_2,
-	DA830_UHPI_HD_3,
-	DA830_UHPI_HD_4,
-	DA830_UHPI_HD_5,
-	DA830_UHPI_HD_6,
-	DA830_UHPI_HD_7,
-	DA830_LCD_D_8,
-	DA830_LCD_D_9,
-	DA830_GPIO0_2,
-	DA830_GPIO0_3,
-	DA830_GPIO0_4,
-	DA830_GPIO0_5,
-	DA830_GPIO0_6,
-	DA830_GPIO0_7,
-	DA830_GPIO0_8,
-	DA830_GPIO0_9,
-	DA830_EMA_D_10,
-	DA830_EMA_D_11,
-	DA830_EMA_D_12,
-	DA830_EMA_D_13,
-	DA830_EMA_D_14,
-	DA830_EMA_D_15,
-	DA830_EMA_A_0,
-	DA830_EMA_A_1,
-	DA830_UHPI_HD_10,
-	DA830_UHPI_HD_11,
-	DA830_UHPI_HD_12,
-	DA830_UHPI_HD_13,
-	DA830_UHPI_HD_14,
-	DA830_UHPI_HD_15,
-	DA830_LCD_D_7,
-	DA830_MMCSD_CLK,
-	DA830_LCD_D_10,
-	DA830_LCD_D_11,
-	DA830_LCD_D_12,
-	DA830_LCD_D_13,
-	DA830_LCD_D_14,
-	DA830_LCD_D_15,
-	DA830_UHPI_HCNTL0,
-	DA830_GPIO0_10,
-	DA830_GPIO0_11,
-	DA830_GPIO0_12,
-	DA830_GPIO0_13,
-	DA830_GPIO0_14,
-	DA830_GPIO0_15,
-	DA830_GPIO1_0,
-	DA830_GPIO1_1,
-	DA830_EMA_A_2,
-	DA830_EMA_A_3,
-	DA830_EMA_A_4,
-	DA830_EMA_A_5,
-	DA830_EMA_A_6,
-	DA830_EMA_A_7,
-	DA830_EMA_A_8,
-	DA830_EMA_A_9,
-	DA830_MMCSD_CMD,
-	DA830_LCD_D_6,
-	DA830_LCD_D_3,
-	DA830_LCD_D_2,
-	DA830_LCD_D_1,
-	DA830_LCD_D_0,
-	DA830_LCD_PCLK,
-	DA830_LCD_HSYNC,
-	DA830_UHPI_HCNTL1,
-	DA830_GPIO1_2,
-	DA830_GPIO1_3,
-	DA830_GPIO1_4,
-	DA830_GPIO1_5,
-	DA830_GPIO1_6,
-	DA830_GPIO1_7,
-	DA830_GPIO1_8,
-	DA830_GPIO1_9,
-	DA830_EMA_A_10,
-	DA830_EMA_A_11,
-	DA830_EMA_A_12,
-	DA830_EMA_BA_1,
-	DA830_EMA_BA_0,
-	DA830_EMA_CLK,
-	DA830_EMA_SDCKE,
-	DA830_NEMA_CAS,
-	DA830_LCD_VSYNC,
-	DA830_NLCD_AC_ENB_CS,
-	DA830_LCD_MCLK,
-	DA830_LCD_D_5,
-	DA830_LCD_D_4,
-	DA830_OBSCLK,
-	DA830_NEMA_CS_4,
-	DA830_UHPI_HHWIL,
-	DA830_AHCLKR2,
-	DA830_GPIO1_10,
-	DA830_GPIO1_11,
-	DA830_GPIO1_12,
-	DA830_GPIO1_13,
-	DA830_GPIO1_14,
-	DA830_GPIO1_15,
-	DA830_GPIO2_0,
-	DA830_GPIO2_1,
-	DA830_NEMA_RAS,
-	DA830_NEMA_WE,
-	DA830_NEMA_CS_0,
-	DA830_NEMA_CS_2,
-	DA830_NEMA_CS_3,
-	DA830_NEMA_OE,
-	DA830_NEMA_WE_DQM_1,
-	DA830_NEMA_WE_DQM_0,
-	DA830_NEMA_CS_5,
-	DA830_UHPI_HRNW,
-	DA830_NUHPI_HAS,
-	DA830_NUHPI_HCS,
-	DA830_NUHPI_HDS1,
-	DA830_NUHPI_HDS2,
-	DA830_NUHPI_HINT,
-	DA830_AXR0_12,
-	DA830_AMUTE2,
-	DA830_AXR0_13,
-	DA830_AXR0_14,
-	DA830_AXR0_15,
-	DA830_GPIO2_2,
-	DA830_GPIO2_3,
-	DA830_GPIO2_4,
-	DA830_GPIO2_5,
-	DA830_GPIO2_6,
-	DA830_GPIO2_7,
-	DA830_GPIO2_8,
-	DA830_GPIO2_9,
-	DA830_EMA_WAIT_0,
-	DA830_NUHPI_HRDY,
-	DA830_GPIO2_10,
-};
-
-enum davinci_da850_index {
-	/* UART0 function */
-	DA850_NUART0_CTS,
-	DA850_NUART0_RTS,
-	DA850_UART0_RXD,
-	DA850_UART0_TXD,
-
-	/* UART1 function */
-	DA850_NUART1_CTS,
-	DA850_NUART1_RTS,
-	DA850_UART1_RXD,
-	DA850_UART1_TXD,
-
-	/* UART2 function */
-	DA850_NUART2_CTS,
-	DA850_NUART2_RTS,
-	DA850_UART2_RXD,
-	DA850_UART2_TXD,
-
-	/* I2C1 function */
-	DA850_I2C1_SCL,
-	DA850_I2C1_SDA,
-
-	/* I2C0 function */
-	DA850_I2C0_SDA,
-	DA850_I2C0_SCL,
-
-	/* EMAC function */
-	DA850_MII_TXEN,
-	DA850_MII_TXCLK,
-	DA850_MII_COL,
-	DA850_MII_TXD_3,
-	DA850_MII_TXD_2,
-	DA850_MII_TXD_1,
-	DA850_MII_TXD_0,
-	DA850_MII_RXER,
-	DA850_MII_CRS,
-	DA850_MII_RXCLK,
-	DA850_MII_RXDV,
-	DA850_MII_RXD_3,
-	DA850_MII_RXD_2,
-	DA850_MII_RXD_1,
-	DA850_MII_RXD_0,
-	DA850_MDIO_CLK,
-	DA850_MDIO_D,
-	DA850_RMII_TXD_0,
-	DA850_RMII_TXD_1,
-	DA850_RMII_TXEN,
-	DA850_RMII_CRS_DV,
-	DA850_RMII_RXD_0,
-	DA850_RMII_RXD_1,
-	DA850_RMII_RXER,
-	DA850_RMII_MHZ_50_CLK,
-
-	/* McASP function */
-	DA850_ACLKR,
-	DA850_ACLKX,
-	DA850_AFSR,
-	DA850_AFSX,
-	DA850_AHCLKR,
-	DA850_AHCLKX,
-	DA850_AMUTE,
-	DA850_AXR_15,
-	DA850_AXR_14,
-	DA850_AXR_13,
-	DA850_AXR_12,
-	DA850_AXR_11,
-	DA850_AXR_10,
-	DA850_AXR_9,
-	DA850_AXR_8,
-	DA850_AXR_7,
-	DA850_AXR_6,
-	DA850_AXR_5,
-	DA850_AXR_4,
-	DA850_AXR_3,
-	DA850_AXR_2,
-	DA850_AXR_1,
-	DA850_AXR_0,
-
-	/* LCD function */
-	DA850_LCD_D_7,
-	DA850_LCD_D_6,
-	DA850_LCD_D_5,
-	DA850_LCD_D_4,
-	DA850_LCD_D_3,
-	DA850_LCD_D_2,
-	DA850_LCD_D_1,
-	DA850_LCD_D_0,
-	DA850_LCD_D_15,
-	DA850_LCD_D_14,
-	DA850_LCD_D_13,
-	DA850_LCD_D_12,
-	DA850_LCD_D_11,
-	DA850_LCD_D_10,
-	DA850_LCD_D_9,
-	DA850_LCD_D_8,
-	DA850_LCD_PCLK,
-	DA850_LCD_HSYNC,
-	DA850_LCD_VSYNC,
-	DA850_NLCD_AC_ENB_CS,
-
-	/* MMC/SD0 function */
-	DA850_MMCSD0_DAT_0,
-	DA850_MMCSD0_DAT_1,
-	DA850_MMCSD0_DAT_2,
-	DA850_MMCSD0_DAT_3,
-	DA850_MMCSD0_CLK,
-	DA850_MMCSD0_CMD,
-
-	/* MMC/SD1 function */
-	DA850_MMCSD1_DAT_0,
-	DA850_MMCSD1_DAT_1,
-	DA850_MMCSD1_DAT_2,
-	DA850_MMCSD1_DAT_3,
-	DA850_MMCSD1_CLK,
-	DA850_MMCSD1_CMD,
-
-	/* EMIF2.5/EMIFA function */
-	DA850_EMA_D_7,
-	DA850_EMA_D_6,
-	DA850_EMA_D_5,
-	DA850_EMA_D_4,
-	DA850_EMA_D_3,
-	DA850_EMA_D_2,
-	DA850_EMA_D_1,
-	DA850_EMA_D_0,
-	DA850_EMA_A_1,
-	DA850_EMA_A_2,
-	DA850_NEMA_CS_3,
-	DA850_NEMA_CS_4,
-	DA850_NEMA_WE,
-	DA850_NEMA_OE,
-	DA850_EMA_D_15,
-	DA850_EMA_D_14,
-	DA850_EMA_D_13,
-	DA850_EMA_D_12,
-	DA850_EMA_D_11,
-	DA850_EMA_D_10,
-	DA850_EMA_D_9,
-	DA850_EMA_D_8,
-	DA850_EMA_A_0,
-	DA850_EMA_A_3,
-	DA850_EMA_A_4,
-	DA850_EMA_A_5,
-	DA850_EMA_A_6,
-	DA850_EMA_A_7,
-	DA850_EMA_A_8,
-	DA850_EMA_A_9,
-	DA850_EMA_A_10,
-	DA850_EMA_A_11,
-	DA850_EMA_A_12,
-	DA850_EMA_A_13,
-	DA850_EMA_A_14,
-	DA850_EMA_A_15,
-	DA850_EMA_A_16,
-	DA850_EMA_A_17,
-	DA850_EMA_A_18,
-	DA850_EMA_A_19,
-	DA850_EMA_A_20,
-	DA850_EMA_A_21,
-	DA850_EMA_A_22,
-	DA850_EMA_A_23,
-	DA850_EMA_BA_1,
-	DA850_EMA_CLK,
-	DA850_EMA_WAIT_1,
-	DA850_NEMA_CS_2,
-
-	/* GPIO function */
-	DA850_GPIO2_4,
-	DA850_GPIO2_6,
-	DA850_GPIO2_8,
-	DA850_GPIO2_15,
-	DA850_GPIO3_12,
-	DA850_GPIO3_13,
-	DA850_GPIO4_0,
-	DA850_GPIO4_1,
-	DA850_GPIO6_9,
-	DA850_GPIO6_10,
-	DA850_GPIO6_13,
-	DA850_RTC_ALARM,
-
-	/* VPIF Capture */
-	DA850_VPIF_DIN0,
-	DA850_VPIF_DIN1,
-	DA850_VPIF_DIN2,
-	DA850_VPIF_DIN3,
-	DA850_VPIF_DIN4,
-	DA850_VPIF_DIN5,
-	DA850_VPIF_DIN6,
-	DA850_VPIF_DIN7,
-	DA850_VPIF_DIN8,
-	DA850_VPIF_DIN9,
-	DA850_VPIF_DIN10,
-	DA850_VPIF_DIN11,
-	DA850_VPIF_DIN12,
-	DA850_VPIF_DIN13,
-	DA850_VPIF_DIN14,
-	DA850_VPIF_DIN15,
-	DA850_VPIF_CLKIN0,
-	DA850_VPIF_CLKIN1,
-	DA850_VPIF_CLKIN2,
-	DA850_VPIF_CLKIN3,
-
-	/* VPIF Display */
-	DA850_VPIF_DOUT0,
-	DA850_VPIF_DOUT1,
-	DA850_VPIF_DOUT2,
-	DA850_VPIF_DOUT3,
-	DA850_VPIF_DOUT4,
-	DA850_VPIF_DOUT5,
-	DA850_VPIF_DOUT6,
-	DA850_VPIF_DOUT7,
-	DA850_VPIF_DOUT8,
-	DA850_VPIF_DOUT9,
-	DA850_VPIF_DOUT10,
-	DA850_VPIF_DOUT11,
-	DA850_VPIF_DOUT12,
-	DA850_VPIF_DOUT13,
-	DA850_VPIF_DOUT14,
-	DA850_VPIF_DOUT15,
-	DA850_VPIF_CLKO2,
-	DA850_VPIF_CLKO3,
-};
-
-#define PINMUX(x)		(4 * (x))
-
-#ifdef CONFIG_DAVINCI_MUX
-/* setup pin muxing */
-extern int davinci_cfg_reg(unsigned long reg_cfg);
-extern int davinci_cfg_reg_list(const short pins[]);
-#else
-/* boot loader does it all (no warnings from CONFIG_DAVINCI_MUX_WARNINGS) */
-static inline int davinci_cfg_reg(unsigned long reg_cfg) { return 0; }
-static inline int davinci_cfg_reg_list(const short pins[])
-{
-	return 0;
-}
-#endif
-
-#endif /* __INC_MACH_MUX_H */
diff --git a/arch/arm/mach-davinci/include/mach/pm.h b/arch/arm/mach-davinci/include/mach/pm.h
deleted file mode 100644
index 5a5f0ecc0704..000000000000
--- a/arch/arm/mach-davinci/include/mach/pm.h
+++ /dev/null
@@ -1,54 +0,0 @@
-/*
- * TI DaVinci platform support for power management.
- *
- * Copyright (C) 2009 Texas Instruments, Inc. https://www.ti.com/
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation version 2.
- *
- * This program is distributed "as is" WITHOUT ANY WARRANTY of any
- * kind, whether express or implied; without even the implied warranty
- * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- */
-#ifndef _MACH_DAVINCI_PM_H
-#define _MACH_DAVINCI_PM_H
-
-/*
- * Caution: Assembly code in sleep.S makes assumtion on the order
- * of the members of this structure.
- */
-struct davinci_pm_config {
-	void __iomem *ddr2_ctlr_base;
-	void __iomem *ddrpsc_reg_base;
-	int ddrpsc_num;
-	void __iomem *ddrpll_reg_base;
-	void __iomem *deepsleep_reg;
-	void __iomem *cpupll_reg_base;
-	/*
-	 * Note on SLEEPCOUNT:
-	 * The SLEEPCOUNT feature is mainly intended for cases in which
-	 * the internal oscillator is used. The internal oscillator is
-	 * fully disabled in deep sleep mode.  When you exist deep sleep
-	 * mode, the oscillator will be turned on and will generate very
-	 * small oscillations which will not be detected by the deep sleep
-	 * counter.  Eventually those oscillations will grow to an amplitude
-	 * large enough to start incrementing the deep sleep counter.
-	 * In this case recommendation from hardware engineers is that the
-	 * SLEEPCOUNT be set to 4096.  This means that 4096 valid clock cycles
-	 * must be detected before the clock is passed to the rest of the
-	 * system.
-	 * In the case that the internal oscillator is not used and the
-	 * clock is generated externally, the SLEEPCOUNT value can be very
-	 * small since the clock input is assumed to be stable before SoC
-	 * is taken out of deepsleep mode.  A value of 128 would be more than
-	 * adequate.
-	 */
-	int sleepcount;
-};
-
-extern unsigned int davinci_cpu_suspend_sz;
-extern void davinci_cpu_suspend(struct davinci_pm_config *);
-
-#endif
diff --git a/arch/arm/mach-davinci/include/mach/serial.h b/arch/arm/mach-davinci/include/mach/serial.h
deleted file mode 100644
index d4b4aa87964f..000000000000
--- a/arch/arm/mach-davinci/include/mach/serial.h
+++ /dev/null
@@ -1,37 +0,0 @@
-/*
- * DaVinci serial device definitions
- *
- * Author: Kevin Hilman, MontaVista Software, Inc. <source@mvista.com>
- *
- * 2007 (c) MontaVista Software, Inc. This file is licensed under
- * the terms of the GNU General Public License version 2. This program
- * is licensed "as is" without any warranty of any kind, whether express
- * or implied.
- */
-#ifndef __ASM_ARCH_SERIAL_H
-#define __ASM_ARCH_SERIAL_H
-
-#include <asm/memory.h>
-
-#include <mach/hardware.h>
-
-#define DAVINCI_UART0_BASE	(IO_PHYS + 0x20000)
-#define DAVINCI_UART1_BASE	(IO_PHYS + 0x20400)
-#define DAVINCI_UART2_BASE	(IO_PHYS + 0x20800)
-
-#define DA8XX_UART0_BASE	(IO_PHYS + 0x042000)
-#define DA8XX_UART1_BASE	(IO_PHYS + 0x10c000)
-#define DA8XX_UART2_BASE	(IO_PHYS + 0x10d000)
-
-/* DaVinci UART register offsets */
-#define UART_DAVINCI_PWREMU		0x0c
-#define UART_DM646X_SCR			0x10
-#define UART_DM646X_SCR_TX_WATERMARK	0x08
-
-#ifndef __ASSEMBLY__
-#include <linux/platform_device.h>
-
-extern int davinci_serial_init(struct platform_device *);
-#endif
-
-#endif /* __ASM_ARCH_SERIAL_H */
diff --git a/arch/arm/mach-davinci/include/mach/uncompress.h b/arch/arm/mach-davinci/include/mach/uncompress.h
deleted file mode 100644
index 53b456a5bbe0..000000000000
--- a/arch/arm/mach-davinci/include/mach/uncompress.h
+++ /dev/null
@@ -1,97 +0,0 @@
-/*
- * Serial port stubs for kernel decompress status messages
- *
- * Initially based on:
- * arch/arm/plat-omap/include/mach/uncompress.h
- *
- * Original copyrights follow.
- *
- * Copyright (C) 2000 RidgeRun, Inc.
- * Author: Greg Lonnon <glonnon@ridgerun.com>
- *
- * Rewritten by:
- * Author: <source@mvista.com>
- * 2004 (c) MontaVista Software, Inc.
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2. This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
- */
-
-#include <linux/types.h>
-#include <linux/serial_reg.h>
-
-#include <asm/mach-types.h>
-
-#include <mach/serial.h>
-
-#define IOMEM(x)	((void __force __iomem *)(x))
-
-u32 *uart;
-
-/* PORT_16C550A, in polled non-fifo mode */
-static inline void putc(char c)
-{
-	if (!uart)
-		return;
-
-	while (!(uart[UART_LSR] & UART_LSR_THRE))
-		barrier();
-	uart[UART_TX] = c;
-}
-
-static inline void flush(void)
-{
-	if (!uart)
-		return;
-
-	while (!(uart[UART_LSR] & UART_LSR_THRE))
-		barrier();
-}
-
-static inline void set_uart_info(u32 phys)
-{
-	uart = (u32 *)phys;
-}
-
-#define _DEBUG_LL_ENTRY(machine, phys)				\
-	{							\
-		if (machine_is_##machine()) {			\
-			set_uart_info(phys);			\
-			break;					\
-		}						\
-	}
-
-#define DEBUG_LL_DAVINCI(machine, port)				\
-	_DEBUG_LL_ENTRY(machine, DAVINCI_UART##port##_BASE)
-
-#define DEBUG_LL_DA8XX(machine, port)				\
-	_DEBUG_LL_ENTRY(machine, DA8XX_UART##port##_BASE)
-
-static inline void __arch_decomp_setup(unsigned long arch_id)
-{
-	/*
-	 * Initialize the port based on the machine ID from the bootloader.
-	 * Note that we're using macros here instead of switch statement
-	 * as machine_is functions are optimized out for the boards that
-	 * are not selected.
-	 */
-	do {
-		/* Davinci boards */
-		DEBUG_LL_DAVINCI(davinci_evm,		0);
-		DEBUG_LL_DAVINCI(sffsdr,		0);
-		DEBUG_LL_DAVINCI(neuros_osd2,		0);
-		DEBUG_LL_DAVINCI(davinci_dm355_evm,	0);
-		DEBUG_LL_DAVINCI(dm355_leopard,		0);
-		DEBUG_LL_DAVINCI(davinci_dm6467_evm,	0);
-		DEBUG_LL_DAVINCI(davinci_dm365_evm,	0);
-
-		/* DA8xx boards */
-		DEBUG_LL_DA8XX(davinci_da830_evm,	2);
-		DEBUG_LL_DA8XX(davinci_da850_evm,	2);
-		DEBUG_LL_DA8XX(mityomapl138,		1);
-		DEBUG_LL_DA8XX(omapl138_hawkboard,	2);
-	} while (0);
-}
-
-#define arch_decomp_setup()	__arch_decomp_setup(arch_id)
diff --git a/arch/arm/mach-davinci/mux.c b/arch/arm/mach-davinci/mux.c
index 6a2ff0a654a5..814a6b714010 100644
--- a/arch/arm/mach-davinci/mux.c
+++ b/arch/arm/mach-davinci/mux.c
@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Utility to set the DAVINCI MUX register from a table in mux.h
  *
@@ -8,10 +9,7 @@
  *
  * Written by Tony Lindgren
  *
- * 2007 (c) MontaVista Software, Inc. This file is licensed under
- * the terms of the GNU General Public License version 2. This program
- * is licensed "as is" without any warranty of any kind, whether express
- * or implied.
+ * 2007 (c) MontaVista Software, Inc.
  *
  * Copyright (C) 2008 Texas Instruments.
  */
@@ -22,8 +20,8 @@
 #include <linux/module.h>
 #include <linux/spinlock.h>
 
-#include <mach/mux.h>
-#include <mach/common.h>
+#include "mux.h"
+#include "common.h"
 
 static void __iomem *pinmux_base;
 
diff --git a/arch/arm/mach-davinci/mux.h b/arch/arm/mach-davinci/mux.h
index 5aad1e7dd210..b5effe16402c 100644
--- a/arch/arm/mach-davinci/mux.h
+++ b/arch/arm/mach-davinci/mux.h
@@ -1,19 +1,984 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * Pin-multiplex helper macros for TI DaVinci family devices
  *
  * Author: Vladimir Barinov, MontaVista Software, Inc. <source@mvista.com>
  *
- * 2007 (c) MontaVista Software, Inc. This file is licensed under
- * the terms of the GNU General Public License version 2. This program
- * is licensed "as is" without any warranty of any kind, whether express
- * or implied.
+ * 2007 (c) MontaVista Software, Inc.
  *
  * Copyright (C) 2008 Texas Instruments.
  */
 #ifndef _MACH_DAVINCI_MUX_H_
 #define _MACH_DAVINCI_MUX_H_
 
-#include <mach/mux.h>
+struct mux_config {
+	const char *name;
+	const char *mux_reg_name;
+	const unsigned char mux_reg;
+	const unsigned char mask_offset;
+	const unsigned char mask;
+	const unsigned char mode;
+	bool debug;
+};
+
+enum davinci_dm644x_index {
+	/* ATA and HDDIR functions */
+	DM644X_HDIREN,
+	DM644X_ATAEN,
+	DM644X_ATAEN_DISABLE,
+
+	/* HPI functions */
+	DM644X_HPIEN_DISABLE,
+
+	/* AEAW functions */
+	DM644X_AEAW,
+	DM644X_AEAW0,
+	DM644X_AEAW1,
+	DM644X_AEAW2,
+	DM644X_AEAW3,
+	DM644X_AEAW4,
+
+	/* Memory Stick */
+	DM644X_MSTK,
+
+	/* I2C */
+	DM644X_I2C,
+
+	/* ASP function */
+	DM644X_MCBSP,
+
+	/* UART1 */
+	DM644X_UART1,
+
+	/* UART2 */
+	DM644X_UART2,
+
+	/* PWM0 */
+	DM644X_PWM0,
+
+	/* PWM1 */
+	DM644X_PWM1,
+
+	/* PWM2 */
+	DM644X_PWM2,
+
+	/* VLYNQ function */
+	DM644X_VLYNQEN,
+	DM644X_VLSCREN,
+	DM644X_VLYNQWD,
+
+	/* EMAC and MDIO function */
+	DM644X_EMACEN,
+
+	/* GPIO3V[0:16] pins */
+	DM644X_GPIO3V,
+
+	/* GPIO pins */
+	DM644X_GPIO0,
+	DM644X_GPIO3,
+	DM644X_GPIO43_44,
+	DM644X_GPIO46_47,
+
+	/* VPBE */
+	DM644X_RGB666,
+
+	/* LCD */
+	DM644X_LOEEN,
+	DM644X_LFLDEN,
+};
+
+enum davinci_dm646x_index {
+	/* ATA function */
+	DM646X_ATAEN,
+
+	/* AUDIO Clock */
+	DM646X_AUDCK1,
+	DM646X_AUDCK0,
+
+	/* CRGEN Control */
+	DM646X_CRGMUX,
+
+	/* VPIF Control */
+	DM646X_STSOMUX_DISABLE,
+	DM646X_STSIMUX_DISABLE,
+	DM646X_PTSOMUX_DISABLE,
+	DM646X_PTSIMUX_DISABLE,
+
+	/* TSIF Control */
+	DM646X_STSOMUX,
+	DM646X_STSIMUX,
+	DM646X_PTSOMUX_PARALLEL,
+	DM646X_PTSIMUX_PARALLEL,
+	DM646X_PTSOMUX_SERIAL,
+	DM646X_PTSIMUX_SERIAL,
+};
+
+enum davinci_dm355_index {
+	/* MMC/SD 0 */
+	DM355_MMCSD0,
+
+	/* MMC/SD 1 */
+	DM355_SD1_CLK,
+	DM355_SD1_CMD,
+	DM355_SD1_DATA3,
+	DM355_SD1_DATA2,
+	DM355_SD1_DATA1,
+	DM355_SD1_DATA0,
+
+	/* I2C */
+	DM355_I2C_SDA,
+	DM355_I2C_SCL,
+
+	/* ASP0 function */
+	DM355_MCBSP0_BDX,
+	DM355_MCBSP0_X,
+	DM355_MCBSP0_BFSX,
+	DM355_MCBSP0_BDR,
+	DM355_MCBSP0_R,
+	DM355_MCBSP0_BFSR,
+
+	/* SPI0 */
+	DM355_SPI0_SDI,
+	DM355_SPI0_SDENA0,
+	DM355_SPI0_SDENA1,
+
+	/* IRQ muxing */
+	DM355_INT_EDMA_CC,
+	DM355_INT_EDMA_TC0_ERR,
+	DM355_INT_EDMA_TC1_ERR,
+
+	/* EDMA event muxing */
+	DM355_EVT8_ASP1_TX,
+	DM355_EVT9_ASP1_RX,
+	DM355_EVT26_MMC0_RX,
+
+	/* Video Out */
+	DM355_VOUT_FIELD,
+	DM355_VOUT_FIELD_G70,
+	DM355_VOUT_HVSYNC,
+	DM355_VOUT_COUTL_EN,
+	DM355_VOUT_COUTH_EN,
+
+	/* Video In Pin Mux */
+	DM355_VIN_PCLK,
+	DM355_VIN_CAM_WEN,
+	DM355_VIN_CAM_VD,
+	DM355_VIN_CAM_HD,
+	DM355_VIN_YIN_EN,
+	DM355_VIN_CINL_EN,
+	DM355_VIN_CINH_EN,
+};
+
+enum davinci_dm365_index {
+	/* MMC/SD 0 */
+	DM365_MMCSD0,
+
+	/* MMC/SD 1 */
+	DM365_SD1_CLK,
+	DM365_SD1_CMD,
+	DM365_SD1_DATA3,
+	DM365_SD1_DATA2,
+	DM365_SD1_DATA1,
+	DM365_SD1_DATA0,
+
+	/* I2C */
+	DM365_I2C_SDA,
+	DM365_I2C_SCL,
+
+	/* AEMIF */
+	DM365_AEMIF_AR_A14,
+	DM365_AEMIF_AR_BA0,
+	DM365_AEMIF_A3,
+	DM365_AEMIF_A7,
+	DM365_AEMIF_D15_8,
+	DM365_AEMIF_CE0,
+	DM365_AEMIF_CE1,
+	DM365_AEMIF_WE_OE,
+
+	/* ASP0 function */
+	DM365_MCBSP0_BDX,
+	DM365_MCBSP0_X,
+	DM365_MCBSP0_BFSX,
+	DM365_MCBSP0_BDR,
+	DM365_MCBSP0_R,
+	DM365_MCBSP0_BFSR,
+
+	/* SPI0 */
+	DM365_SPI0_SCLK,
+	DM365_SPI0_SDI,
+	DM365_SPI0_SDO,
+	DM365_SPI0_SDENA0,
+	DM365_SPI0_SDENA1,
+
+	/* UART */
+	DM365_UART0_RXD,
+	DM365_UART0_TXD,
+	DM365_UART1_RXD,
+	DM365_UART1_TXD,
+	DM365_UART1_RTS,
+	DM365_UART1_CTS,
+
+	/* EMAC */
+	DM365_EMAC_TX_EN,
+	DM365_EMAC_TX_CLK,
+	DM365_EMAC_COL,
+	DM365_EMAC_TXD3,
+	DM365_EMAC_TXD2,
+	DM365_EMAC_TXD1,
+	DM365_EMAC_TXD0,
+	DM365_EMAC_RXD3,
+	DM365_EMAC_RXD2,
+	DM365_EMAC_RXD1,
+	DM365_EMAC_RXD0,
+	DM365_EMAC_RX_CLK,
+	DM365_EMAC_RX_DV,
+	DM365_EMAC_RX_ER,
+	DM365_EMAC_CRS,
+	DM365_EMAC_MDIO,
+	DM365_EMAC_MDCLK,
+
+	/* Key Scan */
+	DM365_KEYSCAN,
+
+	/* PWM */
+	DM365_PWM0,
+	DM365_PWM0_G23,
+	DM365_PWM1,
+	DM365_PWM1_G25,
+	DM365_PWM2_G87,
+	DM365_PWM2_G88,
+	DM365_PWM2_G89,
+	DM365_PWM2_G90,
+	DM365_PWM3_G80,
+	DM365_PWM3_G81,
+	DM365_PWM3_G85,
+	DM365_PWM3_G86,
+
+	/* SPI1 */
+	DM365_SPI1_SCLK,
+	DM365_SPI1_SDO,
+	DM365_SPI1_SDI,
+	DM365_SPI1_SDENA0,
+	DM365_SPI1_SDENA1,
+
+	/* SPI2 */
+	DM365_SPI2_SCLK,
+	DM365_SPI2_SDO,
+	DM365_SPI2_SDI,
+	DM365_SPI2_SDENA0,
+	DM365_SPI2_SDENA1,
+
+	/* SPI3 */
+	DM365_SPI3_SCLK,
+	DM365_SPI3_SDO,
+	DM365_SPI3_SDI,
+	DM365_SPI3_SDENA0,
+	DM365_SPI3_SDENA1,
+
+	/* SPI4 */
+	DM365_SPI4_SCLK,
+	DM365_SPI4_SDO,
+	DM365_SPI4_SDI,
+	DM365_SPI4_SDENA0,
+	DM365_SPI4_SDENA1,
+
+	/* Clock */
+	DM365_CLKOUT0,
+	DM365_CLKOUT1,
+	DM365_CLKOUT2,
+
+	/* GPIO */
+	DM365_GPIO20,
+	DM365_GPIO30,
+	DM365_GPIO31,
+	DM365_GPIO32,
+	DM365_GPIO33,
+	DM365_GPIO40,
+	DM365_GPIO64_57,
+
+	/* Video */
+	DM365_VOUT_FIELD,
+	DM365_VOUT_FIELD_G81,
+	DM365_VOUT_HVSYNC,
+	DM365_VOUT_COUTL_EN,
+	DM365_VOUT_COUTH_EN,
+	DM365_VIN_CAM_WEN,
+	DM365_VIN_CAM_VD,
+	DM365_VIN_CAM_HD,
+	DM365_VIN_YIN4_7_EN,
+	DM365_VIN_YIN0_3_EN,
+
+	/* IRQ muxing */
+	DM365_INT_EDMA_CC,
+	DM365_INT_EDMA_TC0_ERR,
+	DM365_INT_EDMA_TC1_ERR,
+	DM365_INT_EDMA_TC2_ERR,
+	DM365_INT_EDMA_TC3_ERR,
+	DM365_INT_PRTCSS,
+	DM365_INT_EMAC_RXTHRESH,
+	DM365_INT_EMAC_RXPULSE,
+	DM365_INT_EMAC_TXPULSE,
+	DM365_INT_EMAC_MISCPULSE,
+	DM365_INT_IMX0_ENABLE,
+	DM365_INT_IMX0_DISABLE,
+	DM365_INT_HDVICP_ENABLE,
+	DM365_INT_HDVICP_DISABLE,
+	DM365_INT_IMX1_ENABLE,
+	DM365_INT_IMX1_DISABLE,
+	DM365_INT_NSF_ENABLE,
+	DM365_INT_NSF_DISABLE,
+
+	/* EDMA event muxing */
+	DM365_EVT2_ASP_TX,
+	DM365_EVT3_ASP_RX,
+	DM365_EVT2_VC_TX,
+	DM365_EVT3_VC_RX,
+	DM365_EVT26_MMC0_RX,
+};
+
+enum da830_index {
+	DA830_GPIO7_14,
+	DA830_RTCK,
+	DA830_GPIO7_15,
+	DA830_EMU_0,
+	DA830_EMB_SDCKE,
+	DA830_EMB_CLK_GLUE,
+	DA830_EMB_CLK,
+	DA830_NEMB_CS_0,
+	DA830_NEMB_CAS,
+	DA830_NEMB_RAS,
+	DA830_NEMB_WE,
+	DA830_EMB_BA_1,
+	DA830_EMB_BA_0,
+	DA830_EMB_A_0,
+	DA830_EMB_A_1,
+	DA830_EMB_A_2,
+	DA830_EMB_A_3,
+	DA830_EMB_A_4,
+	DA830_EMB_A_5,
+	DA830_GPIO7_0,
+	DA830_GPIO7_1,
+	DA830_GPIO7_2,
+	DA830_GPIO7_3,
+	DA830_GPIO7_4,
+	DA830_GPIO7_5,
+	DA830_GPIO7_6,
+	DA830_GPIO7_7,
+	DA830_EMB_A_6,
+	DA830_EMB_A_7,
+	DA830_EMB_A_8,
+	DA830_EMB_A_9,
+	DA830_EMB_A_10,
+	DA830_EMB_A_11,
+	DA830_EMB_A_12,
+	DA830_EMB_D_31,
+	DA830_GPIO7_8,
+	DA830_GPIO7_9,
+	DA830_GPIO7_10,
+	DA830_GPIO7_11,
+	DA830_GPIO7_12,
+	DA830_GPIO7_13,
+	DA830_GPIO3_13,
+	DA830_EMB_D_30,
+	DA830_EMB_D_29,
+	DA830_EMB_D_28,
+	DA830_EMB_D_27,
+	DA830_EMB_D_26,
+	DA830_EMB_D_25,
+	DA830_EMB_D_24,
+	DA830_EMB_D_23,
+	DA830_EMB_D_22,
+	DA830_EMB_D_21,
+	DA830_EMB_D_20,
+	DA830_EMB_D_19,
+	DA830_EMB_D_18,
+	DA830_EMB_D_17,
+	DA830_EMB_D_16,
+	DA830_NEMB_WE_DQM_3,
+	DA830_NEMB_WE_DQM_2,
+	DA830_EMB_D_0,
+	DA830_EMB_D_1,
+	DA830_EMB_D_2,
+	DA830_EMB_D_3,
+	DA830_EMB_D_4,
+	DA830_EMB_D_5,
+	DA830_EMB_D_6,
+	DA830_GPIO6_0,
+	DA830_GPIO6_1,
+	DA830_GPIO6_2,
+	DA830_GPIO6_3,
+	DA830_GPIO6_4,
+	DA830_GPIO6_5,
+	DA830_GPIO6_6,
+	DA830_EMB_D_7,
+	DA830_EMB_D_8,
+	DA830_EMB_D_9,
+	DA830_EMB_D_10,
+	DA830_EMB_D_11,
+	DA830_EMB_D_12,
+	DA830_EMB_D_13,
+	DA830_EMB_D_14,
+	DA830_GPIO6_7,
+	DA830_GPIO6_8,
+	DA830_GPIO6_9,
+	DA830_GPIO6_10,
+	DA830_GPIO6_11,
+	DA830_GPIO6_12,
+	DA830_GPIO6_13,
+	DA830_GPIO6_14,
+	DA830_EMB_D_15,
+	DA830_NEMB_WE_DQM_1,
+	DA830_NEMB_WE_DQM_0,
+	DA830_SPI0_SOMI_0,
+	DA830_SPI0_SIMO_0,
+	DA830_SPI0_CLK,
+	DA830_NSPI0_ENA,
+	DA830_NSPI0_SCS_0,
+	DA830_EQEP0I,
+	DA830_EQEP0S,
+	DA830_EQEP1I,
+	DA830_NUART0_CTS,
+	DA830_NUART0_RTS,
+	DA830_EQEP0A,
+	DA830_EQEP0B,
+	DA830_GPIO6_15,
+	DA830_GPIO5_14,
+	DA830_GPIO5_15,
+	DA830_GPIO5_0,
+	DA830_GPIO5_1,
+	DA830_GPIO5_2,
+	DA830_GPIO5_3,
+	DA830_GPIO5_4,
+	DA830_SPI1_SOMI_0,
+	DA830_SPI1_SIMO_0,
+	DA830_SPI1_CLK,
+	DA830_UART0_RXD,
+	DA830_UART0_TXD,
+	DA830_AXR1_10,
+	DA830_AXR1_11,
+	DA830_NSPI1_ENA,
+	DA830_I2C1_SCL,
+	DA830_I2C1_SDA,
+	DA830_EQEP1S,
+	DA830_I2C0_SDA,
+	DA830_I2C0_SCL,
+	DA830_UART2_RXD,
+	DA830_TM64P0_IN12,
+	DA830_TM64P0_OUT12,
+	DA830_GPIO5_5,
+	DA830_GPIO5_6,
+	DA830_GPIO5_7,
+	DA830_GPIO5_8,
+	DA830_GPIO5_9,
+	DA830_GPIO5_10,
+	DA830_GPIO5_11,
+	DA830_GPIO5_12,
+	DA830_NSPI1_SCS_0,
+	DA830_USB0_DRVVBUS,
+	DA830_AHCLKX0,
+	DA830_ACLKX0,
+	DA830_AFSX0,
+	DA830_AHCLKR0,
+	DA830_ACLKR0,
+	DA830_AFSR0,
+	DA830_UART2_TXD,
+	DA830_AHCLKX2,
+	DA830_ECAP0_APWM0,
+	DA830_RMII_MHZ_50_CLK,
+	DA830_ECAP1_APWM1,
+	DA830_USB_REFCLKIN,
+	DA830_GPIO5_13,
+	DA830_GPIO4_15,
+	DA830_GPIO2_11,
+	DA830_GPIO2_12,
+	DA830_GPIO2_13,
+	DA830_GPIO2_14,
+	DA830_GPIO2_15,
+	DA830_GPIO3_12,
+	DA830_AMUTE0,
+	DA830_AXR0_0,
+	DA830_AXR0_1,
+	DA830_AXR0_2,
+	DA830_AXR0_3,
+	DA830_AXR0_4,
+	DA830_AXR0_5,
+	DA830_AXR0_6,
+	DA830_RMII_TXD_0,
+	DA830_RMII_TXD_1,
+	DA830_RMII_TXEN,
+	DA830_RMII_CRS_DV,
+	DA830_RMII_RXD_0,
+	DA830_RMII_RXD_1,
+	DA830_RMII_RXER,
+	DA830_AFSR2,
+	DA830_ACLKX2,
+	DA830_AXR2_3,
+	DA830_AXR2_2,
+	DA830_AXR2_1,
+	DA830_AFSX2,
+	DA830_ACLKR2,
+	DA830_NRESETOUT,
+	DA830_GPIO3_0,
+	DA830_GPIO3_1,
+	DA830_GPIO3_2,
+	DA830_GPIO3_3,
+	DA830_GPIO3_4,
+	DA830_GPIO3_5,
+	DA830_GPIO3_6,
+	DA830_AXR0_7,
+	DA830_AXR0_8,
+	DA830_UART1_RXD,
+	DA830_UART1_TXD,
+	DA830_AXR0_11,
+	DA830_AHCLKX1,
+	DA830_ACLKX1,
+	DA830_AFSX1,
+	DA830_MDIO_CLK,
+	DA830_MDIO_D,
+	DA830_AXR0_9,
+	DA830_AXR0_10,
+	DA830_EPWM0B,
+	DA830_EPWM0A,
+	DA830_EPWMSYNCI,
+	DA830_AXR2_0,
+	DA830_EPWMSYNC0,
+	DA830_GPIO3_7,
+	DA830_GPIO3_8,
+	DA830_GPIO3_9,
+	DA830_GPIO3_10,
+	DA830_GPIO3_11,
+	DA830_GPIO3_14,
+	DA830_GPIO3_15,
+	DA830_GPIO4_10,
+	DA830_AHCLKR1,
+	DA830_ACLKR1,
+	DA830_AFSR1,
+	DA830_AMUTE1,
+	DA830_AXR1_0,
+	DA830_AXR1_1,
+	DA830_AXR1_2,
+	DA830_AXR1_3,
+	DA830_ECAP2_APWM2,
+	DA830_EHRPWMGLUETZ,
+	DA830_EQEP1A,
+	DA830_GPIO4_11,
+	DA830_GPIO4_12,
+	DA830_GPIO4_13,
+	DA830_GPIO4_14,
+	DA830_GPIO4_0,
+	DA830_GPIO4_1,
+	DA830_GPIO4_2,
+	DA830_GPIO4_3,
+	DA830_AXR1_4,
+	DA830_AXR1_5,
+	DA830_AXR1_6,
+	DA830_AXR1_7,
+	DA830_AXR1_8,
+	DA830_AXR1_9,
+	DA830_EMA_D_0,
+	DA830_EMA_D_1,
+	DA830_EQEP1B,
+	DA830_EPWM2B,
+	DA830_EPWM2A,
+	DA830_EPWM1B,
+	DA830_EPWM1A,
+	DA830_MMCSD_DAT_0,
+	DA830_MMCSD_DAT_1,
+	DA830_UHPI_HD_0,
+	DA830_UHPI_HD_1,
+	DA830_GPIO4_4,
+	DA830_GPIO4_5,
+	DA830_GPIO4_6,
+	DA830_GPIO4_7,
+	DA830_GPIO4_8,
+	DA830_GPIO4_9,
+	DA830_GPIO0_0,
+	DA830_GPIO0_1,
+	DA830_EMA_D_2,
+	DA830_EMA_D_3,
+	DA830_EMA_D_4,
+	DA830_EMA_D_5,
+	DA830_EMA_D_6,
+	DA830_EMA_D_7,
+	DA830_EMA_D_8,
+	DA830_EMA_D_9,
+	DA830_MMCSD_DAT_2,
+	DA830_MMCSD_DAT_3,
+	DA830_MMCSD_DAT_4,
+	DA830_MMCSD_DAT_5,
+	DA830_MMCSD_DAT_6,
+	DA830_MMCSD_DAT_7,
+	DA830_UHPI_HD_8,
+	DA830_UHPI_HD_9,
+	DA830_UHPI_HD_2,
+	DA830_UHPI_HD_3,
+	DA830_UHPI_HD_4,
+	DA830_UHPI_HD_5,
+	DA830_UHPI_HD_6,
+	DA830_UHPI_HD_7,
+	DA830_LCD_D_8,
+	DA830_LCD_D_9,
+	DA830_GPIO0_2,
+	DA830_GPIO0_3,
+	DA830_GPIO0_4,
+	DA830_GPIO0_5,
+	DA830_GPIO0_6,
+	DA830_GPIO0_7,
+	DA830_GPIO0_8,
+	DA830_GPIO0_9,
+	DA830_EMA_D_10,
+	DA830_EMA_D_11,
+	DA830_EMA_D_12,
+	DA830_EMA_D_13,
+	DA830_EMA_D_14,
+	DA830_EMA_D_15,
+	DA830_EMA_A_0,
+	DA830_EMA_A_1,
+	DA830_UHPI_HD_10,
+	DA830_UHPI_HD_11,
+	DA830_UHPI_HD_12,
+	DA830_UHPI_HD_13,
+	DA830_UHPI_HD_14,
+	DA830_UHPI_HD_15,
+	DA830_LCD_D_7,
+	DA830_MMCSD_CLK,
+	DA830_LCD_D_10,
+	DA830_LCD_D_11,
+	DA830_LCD_D_12,
+	DA830_LCD_D_13,
+	DA830_LCD_D_14,
+	DA830_LCD_D_15,
+	DA830_UHPI_HCNTL0,
+	DA830_GPIO0_10,
+	DA830_GPIO0_11,
+	DA830_GPIO0_12,
+	DA830_GPIO0_13,
+	DA830_GPIO0_14,
+	DA830_GPIO0_15,
+	DA830_GPIO1_0,
+	DA830_GPIO1_1,
+	DA830_EMA_A_2,
+	DA830_EMA_A_3,
+	DA830_EMA_A_4,
+	DA830_EMA_A_5,
+	DA830_EMA_A_6,
+	DA830_EMA_A_7,
+	DA830_EMA_A_8,
+	DA830_EMA_A_9,
+	DA830_MMCSD_CMD,
+	DA830_LCD_D_6,
+	DA830_LCD_D_3,
+	DA830_LCD_D_2,
+	DA830_LCD_D_1,
+	DA830_LCD_D_0,
+	DA830_LCD_PCLK,
+	DA830_LCD_HSYNC,
+	DA830_UHPI_HCNTL1,
+	DA830_GPIO1_2,
+	DA830_GPIO1_3,
+	DA830_GPIO1_4,
+	DA830_GPIO1_5,
+	DA830_GPIO1_6,
+	DA830_GPIO1_7,
+	DA830_GPIO1_8,
+	DA830_GPIO1_9,
+	DA830_EMA_A_10,
+	DA830_EMA_A_11,
+	DA830_EMA_A_12,
+	DA830_EMA_BA_1,
+	DA830_EMA_BA_0,
+	DA830_EMA_CLK,
+	DA830_EMA_SDCKE,
+	DA830_NEMA_CAS,
+	DA830_LCD_VSYNC,
+	DA830_NLCD_AC_ENB_CS,
+	DA830_LCD_MCLK,
+	DA830_LCD_D_5,
+	DA830_LCD_D_4,
+	DA830_OBSCLK,
+	DA830_NEMA_CS_4,
+	DA830_UHPI_HHWIL,
+	DA830_AHCLKR2,
+	DA830_GPIO1_10,
+	DA830_GPIO1_11,
+	DA830_GPIO1_12,
+	DA830_GPIO1_13,
+	DA830_GPIO1_14,
+	DA830_GPIO1_15,
+	DA830_GPIO2_0,
+	DA830_GPIO2_1,
+	DA830_NEMA_RAS,
+	DA830_NEMA_WE,
+	DA830_NEMA_CS_0,
+	DA830_NEMA_CS_2,
+	DA830_NEMA_CS_3,
+	DA830_NEMA_OE,
+	DA830_NEMA_WE_DQM_1,
+	DA830_NEMA_WE_DQM_0,
+	DA830_NEMA_CS_5,
+	DA830_UHPI_HRNW,
+	DA830_NUHPI_HAS,
+	DA830_NUHPI_HCS,
+	DA830_NUHPI_HDS1,
+	DA830_NUHPI_HDS2,
+	DA830_NUHPI_HINT,
+	DA830_AXR0_12,
+	DA830_AMUTE2,
+	DA830_AXR0_13,
+	DA830_AXR0_14,
+	DA830_AXR0_15,
+	DA830_GPIO2_2,
+	DA830_GPIO2_3,
+	DA830_GPIO2_4,
+	DA830_GPIO2_5,
+	DA830_GPIO2_6,
+	DA830_GPIO2_7,
+	DA830_GPIO2_8,
+	DA830_GPIO2_9,
+	DA830_EMA_WAIT_0,
+	DA830_NUHPI_HRDY,
+	DA830_GPIO2_10,
+};
+
+enum davinci_da850_index {
+	/* UART0 function */
+	DA850_NUART0_CTS,
+	DA850_NUART0_RTS,
+	DA850_UART0_RXD,
+	DA850_UART0_TXD,
+
+	/* UART1 function */
+	DA850_NUART1_CTS,
+	DA850_NUART1_RTS,
+	DA850_UART1_RXD,
+	DA850_UART1_TXD,
+
+	/* UART2 function */
+	DA850_NUART2_CTS,
+	DA850_NUART2_RTS,
+	DA850_UART2_RXD,
+	DA850_UART2_TXD,
+
+	/* I2C1 function */
+	DA850_I2C1_SCL,
+	DA850_I2C1_SDA,
+
+	/* I2C0 function */
+	DA850_I2C0_SDA,
+	DA850_I2C0_SCL,
+
+	/* EMAC function */
+	DA850_MII_TXEN,
+	DA850_MII_TXCLK,
+	DA850_MII_COL,
+	DA850_MII_TXD_3,
+	DA850_MII_TXD_2,
+	DA850_MII_TXD_1,
+	DA850_MII_TXD_0,
+	DA850_MII_RXER,
+	DA850_MII_CRS,
+	DA850_MII_RXCLK,
+	DA850_MII_RXDV,
+	DA850_MII_RXD_3,
+	DA850_MII_RXD_2,
+	DA850_MII_RXD_1,
+	DA850_MII_RXD_0,
+	DA850_MDIO_CLK,
+	DA850_MDIO_D,
+	DA850_RMII_TXD_0,
+	DA850_RMII_TXD_1,
+	DA850_RMII_TXEN,
+	DA850_RMII_CRS_DV,
+	DA850_RMII_RXD_0,
+	DA850_RMII_RXD_1,
+	DA850_RMII_RXER,
+	DA850_RMII_MHZ_50_CLK,
+
+	/* McASP function */
+	DA850_ACLKR,
+	DA850_ACLKX,
+	DA850_AFSR,
+	DA850_AFSX,
+	DA850_AHCLKR,
+	DA850_AHCLKX,
+	DA850_AMUTE,
+	DA850_AXR_15,
+	DA850_AXR_14,
+	DA850_AXR_13,
+	DA850_AXR_12,
+	DA850_AXR_11,
+	DA850_AXR_10,
+	DA850_AXR_9,
+	DA850_AXR_8,
+	DA850_AXR_7,
+	DA850_AXR_6,
+	DA850_AXR_5,
+	DA850_AXR_4,
+	DA850_AXR_3,
+	DA850_AXR_2,
+	DA850_AXR_1,
+	DA850_AXR_0,
+
+	/* LCD function */
+	DA850_LCD_D_7,
+	DA850_LCD_D_6,
+	DA850_LCD_D_5,
+	DA850_LCD_D_4,
+	DA850_LCD_D_3,
+	DA850_LCD_D_2,
+	DA850_LCD_D_1,
+	DA850_LCD_D_0,
+	DA850_LCD_D_15,
+	DA850_LCD_D_14,
+	DA850_LCD_D_13,
+	DA850_LCD_D_12,
+	DA850_LCD_D_11,
+	DA850_LCD_D_10,
+	DA850_LCD_D_9,
+	DA850_LCD_D_8,
+	DA850_LCD_PCLK,
+	DA850_LCD_HSYNC,
+	DA850_LCD_VSYNC,
+	DA850_NLCD_AC_ENB_CS,
+
+	/* MMC/SD0 function */
+	DA850_MMCSD0_DAT_0,
+	DA850_MMCSD0_DAT_1,
+	DA850_MMCSD0_DAT_2,
+	DA850_MMCSD0_DAT_3,
+	DA850_MMCSD0_CLK,
+	DA850_MMCSD0_CMD,
+
+	/* MMC/SD1 function */
+	DA850_MMCSD1_DAT_0,
+	DA850_MMCSD1_DAT_1,
+	DA850_MMCSD1_DAT_2,
+	DA850_MMCSD1_DAT_3,
+	DA850_MMCSD1_CLK,
+	DA850_MMCSD1_CMD,
+
+	/* EMIF2.5/EMIFA function */
+	DA850_EMA_D_7,
+	DA850_EMA_D_6,
+	DA850_EMA_D_5,
+	DA850_EMA_D_4,
+	DA850_EMA_D_3,
+	DA850_EMA_D_2,
+	DA850_EMA_D_1,
+	DA850_EMA_D_0,
+	DA850_EMA_A_1,
+	DA850_EMA_A_2,
+	DA850_NEMA_CS_3,
+	DA850_NEMA_CS_4,
+	DA850_NEMA_WE,
+	DA850_NEMA_OE,
+	DA850_EMA_D_15,
+	DA850_EMA_D_14,
+	DA850_EMA_D_13,
+	DA850_EMA_D_12,
+	DA850_EMA_D_11,
+	DA850_EMA_D_10,
+	DA850_EMA_D_9,
+	DA850_EMA_D_8,
+	DA850_EMA_A_0,
+	DA850_EMA_A_3,
+	DA850_EMA_A_4,
+	DA850_EMA_A_5,
+	DA850_EMA_A_6,
+	DA850_EMA_A_7,
+	DA850_EMA_A_8,
+	DA850_EMA_A_9,
+	DA850_EMA_A_10,
+	DA850_EMA_A_11,
+	DA850_EMA_A_12,
+	DA850_EMA_A_13,
+	DA850_EMA_A_14,
+	DA850_EMA_A_15,
+	DA850_EMA_A_16,
+	DA850_EMA_A_17,
+	DA850_EMA_A_18,
+	DA850_EMA_A_19,
+	DA850_EMA_A_20,
+	DA850_EMA_A_21,
+	DA850_EMA_A_22,
+	DA850_EMA_A_23,
+	DA850_EMA_BA_1,
+	DA850_EMA_CLK,
+	DA850_EMA_WAIT_1,
+	DA850_NEMA_CS_2,
+
+	/* GPIO function */
+	DA850_GPIO2_4,
+	DA850_GPIO2_6,
+	DA850_GPIO2_8,
+	DA850_GPIO2_15,
+	DA850_GPIO3_12,
+	DA850_GPIO3_13,
+	DA850_GPIO4_0,
+	DA850_GPIO4_1,
+	DA850_GPIO6_9,
+	DA850_GPIO6_10,
+	DA850_GPIO6_13,
+	DA850_RTC_ALARM,
+
+	/* VPIF Capture */
+	DA850_VPIF_DIN0,
+	DA850_VPIF_DIN1,
+	DA850_VPIF_DIN2,
+	DA850_VPIF_DIN3,
+	DA850_VPIF_DIN4,
+	DA850_VPIF_DIN5,
+	DA850_VPIF_DIN6,
+	DA850_VPIF_DIN7,
+	DA850_VPIF_DIN8,
+	DA850_VPIF_DIN9,
+	DA850_VPIF_DIN10,
+	DA850_VPIF_DIN11,
+	DA850_VPIF_DIN12,
+	DA850_VPIF_DIN13,
+	DA850_VPIF_DIN14,
+	DA850_VPIF_DIN15,
+	DA850_VPIF_CLKIN0,
+	DA850_VPIF_CLKIN1,
+	DA850_VPIF_CLKIN2,
+	DA850_VPIF_CLKIN3,
+
+	/* VPIF Display */
+	DA850_VPIF_DOUT0,
+	DA850_VPIF_DOUT1,
+	DA850_VPIF_DOUT2,
+	DA850_VPIF_DOUT3,
+	DA850_VPIF_DOUT4,
+	DA850_VPIF_DOUT5,
+	DA850_VPIF_DOUT6,
+	DA850_VPIF_DOUT7,
+	DA850_VPIF_DOUT8,
+	DA850_VPIF_DOUT9,
+	DA850_VPIF_DOUT10,
+	DA850_VPIF_DOUT11,
+	DA850_VPIF_DOUT12,
+	DA850_VPIF_DOUT13,
+	DA850_VPIF_DOUT14,
+	DA850_VPIF_DOUT15,
+	DA850_VPIF_CLKO2,
+	DA850_VPIF_CLKO3,
+};
+
+#define PINMUX(x)		(4 * (x))
+
+#ifdef CONFIG_DAVINCI_MUX
+/* setup pin muxing */
+extern int davinci_cfg_reg(unsigned long reg_cfg);
+extern int davinci_cfg_reg_list(const short pins[]);
+#else
+/* boot loader does it all (no warnings from CONFIG_DAVINCI_MUX_WARNINGS) */
+static inline int davinci_cfg_reg(unsigned long reg_cfg) { return 0; }
+static inline int davinci_cfg_reg_list(const short pins[])
+{
+	return 0;
+}
+#endif
+
 
 #define MUX_CFG(soc, desc, muxreg, mode_offset, mode_mask, mux_mode, dbg)\
 [soc##_##desc] = {							\
diff --git a/arch/arm/mach-davinci/pdata-quirks.c b/arch/arm/mach-davinci/pdata-quirks.c
index 67f1c8537354..b8b5f1a5e092 100644
--- a/arch/arm/mach-davinci/pdata-quirks.c
+++ b/arch/arm/mach-davinci/pdata-quirks.c
@@ -10,8 +10,8 @@
 #include <media/i2c/tvp514x.h>
 #include <media/i2c/adv7343.h>
 
-#include <mach/common.h>
-#include <mach/da8xx.h>
+#include "common.h"
+#include "da8xx.h"
 
 struct pdata_init {
 	const char *compatible;
diff --git a/arch/arm/mach-davinci/pm.c b/arch/arm/mach-davinci/pm.c
index 323ee4e657c4..8aa39db095d7 100644
--- a/arch/arm/mach-davinci/pm.c
+++ b/arch/arm/mach-davinci/pm.c
@@ -16,11 +16,10 @@
 #include <asm/delay.h>
 #include <asm/io.h>
 
-#include <mach/common.h>
-#include <mach/da8xx.h>
-#include <mach/mux.h>
-#include <mach/pm.h>
-
+#include "common.h"
+#include "da8xx.h"
+#include "mux.h"
+#include "pm.h"
 #include "clock.h"
 #include "psc.h"
 #include "sram.h"
diff --git a/arch/arm/mach-davinci/pm.h b/arch/arm/mach-davinci/pm.h
new file mode 100644
index 000000000000..6f50d6eb8da8
--- /dev/null
+++ b/arch/arm/mach-davinci/pm.h
@@ -0,0 +1,46 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * TI DaVinci platform support for power management.
+ *
+ * Copyright (C) 2009 Texas Instruments, Inc. https://www.ti.com/
+ */
+#ifndef _MACH_DAVINCI_PM_H
+#define _MACH_DAVINCI_PM_H
+
+/*
+ * Caution: Assembly code in sleep.S makes assumtion on the order
+ * of the members of this structure.
+ */
+struct davinci_pm_config {
+	void __iomem *ddr2_ctlr_base;
+	void __iomem *ddrpsc_reg_base;
+	int ddrpsc_num;
+	void __iomem *ddrpll_reg_base;
+	void __iomem *deepsleep_reg;
+	void __iomem *cpupll_reg_base;
+	/*
+	 * Note on SLEEPCOUNT:
+	 * The SLEEPCOUNT feature is mainly intended for cases in which
+	 * the internal oscillator is used. The internal oscillator is
+	 * fully disabled in deep sleep mode.  When you exist deep sleep
+	 * mode, the oscillator will be turned on and will generate very
+	 * small oscillations which will not be detected by the deep sleep
+	 * counter.  Eventually those oscillations will grow to an amplitude
+	 * large enough to start incrementing the deep sleep counter.
+	 * In this case recommendation from hardware engineers is that the
+	 * SLEEPCOUNT be set to 4096.  This means that 4096 valid clock cycles
+	 * must be detected before the clock is passed to the rest of the
+	 * system.
+	 * In the case that the internal oscillator is not used and the
+	 * clock is generated externally, the SLEEPCOUNT value can be very
+	 * small since the clock input is assumed to be stable before SoC
+	 * is taken out of deepsleep mode.  A value of 128 would be more than
+	 * adequate.
+	 */
+	int sleepcount;
+};
+
+extern unsigned int davinci_cpu_suspend_sz;
+extern void davinci_cpu_suspend(struct davinci_pm_config *);
+
+#endif
diff --git a/arch/arm/mach-davinci/pm_domain.c b/arch/arm/mach-davinci/pm_domain.c
index e251fd593bfd..6b21d5bd999c 100644
--- a/arch/arm/mach-davinci/pm_domain.c
+++ b/arch/arm/mach-davinci/pm_domain.c
@@ -1,13 +1,10 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Runtime PM support code for DaVinci
  *
  * Author: Kevin Hilman
  *
  * Copyright (C) 2012 Texas Instruments, Inc.
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 #include <linux/init.h>
 #include <linux/pm_runtime.h>
diff --git a/arch/arm/mach-davinci/serial.c b/arch/arm/mach-davinci/serial.c
index 127b62ce7b1e..7f7814807bb5 100644
--- a/arch/arm/mach-davinci/serial.c
+++ b/arch/arm/mach-davinci/serial.c
@@ -14,8 +14,8 @@
 #include <linux/clk.h>
 #include <linux/io.h>
 
-#include <mach/serial.h>
-#include <mach/cputype.h>
+#include "serial.h"
+#include "cputype.h"
 
 static inline void serial_write_reg(struct plat_serial8250_port *p, int offset,
 				    int value)
diff --git a/arch/arm/mach-davinci/serial.h b/arch/arm/mach-davinci/serial.h
new file mode 100644
index 000000000000..c4a4ba553d45
--- /dev/null
+++ b/arch/arm/mach-davinci/serial.h
@@ -0,0 +1,35 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * DaVinci serial device definitions
+ *
+ * Author: Kevin Hilman, MontaVista Software, Inc. <source@mvista.com>
+ *
+ * 2007 (c) MontaVista Software, Inc.
+ */
+#ifndef __ASM_ARCH_SERIAL_H
+#define __ASM_ARCH_SERIAL_H
+
+#include <asm/memory.h>
+
+#include "hardware.h"
+
+#define DAVINCI_UART0_BASE	(IO_PHYS + 0x20000)
+#define DAVINCI_UART1_BASE	(IO_PHYS + 0x20400)
+#define DAVINCI_UART2_BASE	(IO_PHYS + 0x20800)
+
+#define DA8XX_UART0_BASE	(IO_PHYS + 0x042000)
+#define DA8XX_UART1_BASE	(IO_PHYS + 0x10c000)
+#define DA8XX_UART2_BASE	(IO_PHYS + 0x10d000)
+
+/* DaVinci UART register offsets */
+#define UART_DAVINCI_PWREMU		0x0c
+#define UART_DM646X_SCR			0x10
+#define UART_DM646X_SCR_TX_WATERMARK	0x08
+
+#ifndef __ASSEMBLY__
+#include <linux/platform_device.h>
+
+extern int davinci_serial_init(struct platform_device *);
+#endif
+
+#endif /* __ASM_ARCH_SERIAL_H */
diff --git a/arch/arm/mach-davinci/sram.c b/arch/arm/mach-davinci/sram.c
index bbae190fd82c..d04f39fc84b6 100644
--- a/arch/arm/mach-davinci/sram.c
+++ b/arch/arm/mach-davinci/sram.c
@@ -9,7 +9,7 @@
 #include <linux/io.h>
 #include <linux/genalloc.h>
 
-#include <mach/common.h>
+#include "common.h"
 #include "sram.h"
 
 static struct gen_pool *sram_pool;
diff --git a/arch/arm/mach-davinci/usb-da8xx.c b/arch/arm/mach-davinci/usb-da8xx.c
index 25f21ee86f1a..9c8fc5031907 100644
--- a/arch/arm/mach-davinci/usb-da8xx.c
+++ b/arch/arm/mach-davinci/usb-da8xx.c
@@ -15,10 +15,9 @@
 #include <linux/platform_device.h>
 #include <linux/usb/musb.h>
 
-#include <mach/common.h>
-#include <mach/cputype.h>
-#include <mach/da8xx.h>
-
+#include "common.h"
+#include "cputype.h"
+#include "da8xx.h"
 #include "irqs.h"
 
 #define DA8XX_USB0_BASE		0x01e00000
diff --git a/arch/arm/mach-davinci/usb.c b/arch/arm/mach-davinci/usb.c
index dd8db61cdd1c..a9e5c6e91e5d 100644
--- a/arch/arm/mach-davinci/usb.c
+++ b/arch/arm/mach-davinci/usb.c
@@ -8,9 +8,8 @@
 #include <linux/platform_data/usb-davinci.h>
 #include <linux/usb/musb.h>
 
-#include <mach/common.h>
-#include <mach/cputype.h>
-
+#include "common.h"
+#include "cputype.h"
 #include "irqs.h"
 
 #define DAVINCI_USB_OTG_BASE	0x01c64000
diff --git a/arch/arm/mach-dove/Kconfig b/arch/arm/mach-dove/Kconfig
index 7747fe64420a..2252f465cafd 100644
--- a/arch/arm/mach-dove/Kconfig
+++ b/arch/arm/mach-dove/Kconfig
@@ -1,7 +1,19 @@
 # SPDX-License-Identifier: GPL-2.0
-if ARCH_DOVE
+menuconfig ARCH_DOVE
+	bool "Marvell Dove" if ARCH_MULTI_V7
+	depends on ATAGS
+	select CPU_PJ4
+	select GPIOLIB
+	select MVEBU_MBUS
+	select PINCTRL
+	select PINCTRL_DOVE
+	select PLAT_ORION_LEGACY
+	select PM_GENERIC_DOMAINS if PM
+	select PCI_QUIRKS if PCI
+	help
+	  Support for the Marvell Dove SoC 88AP510
 
-menu "Marvell Dove Implementations"
+if ARCH_DOVE
 
 config DOVE_LEGACY
 	bool
@@ -21,6 +33,4 @@ config MACH_CM_A510
 	  Say 'Y' here if you want your kernel to support the
 	  CompuLab CM-A510 Board.
 
-endmenu
-
 endif
diff --git a/arch/arm/mach-dove/Makefile b/arch/arm/mach-dove/Makefile
index cdf163cab738..da373a5768ba 100644
--- a/arch/arm/mach-dove/Makefile
+++ b/arch/arm/mach-dove/Makefile
@@ -1,4 +1,6 @@
 # SPDX-License-Identifier: GPL-2.0
+ccflags-y := -I$(srctree)/arch/arm/plat-orion/include
+
 obj-y				+= common.o
 obj-$(CONFIG_DOVE_LEGACY)	+= irq.o mpp.o
 obj-$(CONFIG_PCI)		+= pcie.o
diff --git a/arch/arm/mach-dove/Makefile.boot b/arch/arm/mach-dove/Makefile.boot
deleted file mode 100644
index e4dd1d26038f..000000000000
--- a/arch/arm/mach-dove/Makefile.boot
+++ /dev/null
@@ -1,4 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0-only
-   zreladdr-y	+= 0x00008000
-params_phys-y	:= 0x00000100
-initrd_phys-y	:= 0x00800000
diff --git a/arch/arm/mach-dove/bridge-regs.h b/arch/arm/mach-dove/bridge-regs.h
index ace0b0bfbf11..6fbc152d0950 100644
--- a/arch/arm/mach-dove/bridge-regs.h
+++ b/arch/arm/mach-dove/bridge-regs.h
@@ -1,10 +1,5 @@
-/*
- * Mbus-L to Mbus Bridge Registers
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
+/* SPDX-License-Identifier: GPL-2.0-only */
+/* Mbus-L to Mbus Bridge Registers */
 
 #ifndef __ASM_ARCH_BRIDGE_REGS_H
 #define __ASM_ARCH_BRIDGE_REGS_H
diff --git a/arch/arm/mach-dove/cm-a510.c b/arch/arm/mach-dove/cm-a510.c
index 9f25c993d863..beb532537c22 100644
--- a/arch/arm/mach-dove/cm-a510.c
+++ b/arch/arm/mach-dove/cm-a510.c
@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/mach-dove/cm-a510.c
  *
@@ -5,10 +6,6 @@
  * Konstantin Sinyuk <kostyas@compulab.co.il>
  *
  * Based on Marvell DB-MV88AP510-BP Development Board Setup
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #include <linux/kernel.h>
diff --git a/arch/arm/mach-dove/common.c b/arch/arm/mach-dove/common.c
index dbe970e37895..cd4ae7e4768d 100644
--- a/arch/arm/mach-dove/common.c
+++ b/arch/arm/mach-dove/common.c
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/mach-dove/common.c
  *
  * Core functions for Marvell Dove 88AP510 System On Chip
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #include <linux/clk-provider.h>
diff --git a/arch/arm/mach-dove/common.h b/arch/arm/mach-dove/common.h
index 1d725224d146..57ebc413d68c 100644
--- a/arch/arm/mach-dove/common.h
+++ b/arch/arm/mach-dove/common.h
@@ -1,11 +1,8 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * arch/arm/mach-dove/common.h
  *
  * Core functions for Marvell Dove 88AP510 System On Chip
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #ifndef __ARCH_DOVE_COMMON_H
diff --git a/arch/arm/mach-dove/dove-db-setup.c b/arch/arm/mach-dove/dove-db-setup.c
index 418ab21b9d9b..d5bf54040577 100644
--- a/arch/arm/mach-dove/dove-db-setup.c
+++ b/arch/arm/mach-dove/dove-db-setup.c
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/mach-dove/dove-db-setup.c
  *
  * Marvell DB-MV88AP510-BP Development Board Setup
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #include <linux/kernel.h>
diff --git a/arch/arm/mach-dove/dove.h b/arch/arm/mach-dove/dove.h
index 320ed1696abd..e5054e3b0b78 100644
--- a/arch/arm/mach-dove/dove.h
+++ b/arch/arm/mach-dove/dove.h
@@ -1,10 +1,5 @@
-/*
- * Generic definitions for Marvell Dove 88AP510 SoC
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
+/* SPDX-License-Identifier: GPL-2.0-only */
+/* Generic definitions for Marvell Dove 88AP510 SoC */
 
 #ifndef __ASM_ARCH_DOVE_H
 #define __ASM_ARCH_DOVE_H
diff --git a/arch/arm/mach-dove/include/mach/uncompress.h b/arch/arm/mach-dove/include/mach/uncompress.h
deleted file mode 100644
index ddf873f35e2b..000000000000
--- a/arch/arm/mach-dove/include/mach/uncompress.h
+++ /dev/null
@@ -1,34 +0,0 @@
-/*
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#define UART0_PHYS_BASE (0xf1000000 + 0x12000)
-
-#define UART_THR ((volatile unsigned char *)(UART0_PHYS_BASE + 0x0))
-#define UART_LSR ((volatile unsigned char *)(UART0_PHYS_BASE + 0x14))
-
-#define LSR_THRE	0x20
-
-static inline void putc(const char c)
-{
-	int i;
-
-	for (i = 0; i < 0x1000; i++) {
-		/* Transmit fifo not full? */
-		if (*UART_LSR & LSR_THRE)
-			break;
-	}
-
-	*UART_THR = c;
-}
-
-static inline void flush(void)
-{
-}
-
-/*
- * nothing to do
- */
-#define arch_decomp_setup()
diff --git a/arch/arm/mach-dove/irq.c b/arch/arm/mach-dove/irq.c
index 31ccbcee2627..027a8f87bc2e 100644
--- a/arch/arm/mach-dove/irq.c
+++ b/arch/arm/mach-dove/irq.c
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/mach-dove/irq.c
  *
  * Dove IRQ handling.
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 #include <linux/init.h>
 #include <linux/irq.h>
@@ -73,12 +70,12 @@ void __init dove_init_irq(void)
 	/*
 	 * Initialize gpiolib for GPIOs 0-71.
 	 */
-	orion_gpio_init(NULL, 0, 32, DOVE_GPIO_LO_VIRT_BASE, 0,
+	orion_gpio_init(0, 32, DOVE_GPIO_LO_VIRT_BASE, 0,
 			IRQ_DOVE_GPIO_START, gpio0_irqs);
 
-	orion_gpio_init(NULL, 32, 32, DOVE_GPIO_HI_VIRT_BASE, 0,
+	orion_gpio_init(32, 32, DOVE_GPIO_HI_VIRT_BASE, 0,
 			IRQ_DOVE_GPIO_START + 32, gpio1_irqs);
 
-	orion_gpio_init(NULL, 64, 8, DOVE_GPIO2_VIRT_BASE, 0,
+	orion_gpio_init(64, 8, DOVE_GPIO2_VIRT_BASE, 0,
 			IRQ_DOVE_GPIO_START + 64, gpio2_irqs);
 }
diff --git a/arch/arm/mach-dove/irqs.h b/arch/arm/mach-dove/irqs.h
index a0742179faff..5467098c7042 100644
--- a/arch/arm/mach-dove/irqs.h
+++ b/arch/arm/mach-dove/irqs.h
@@ -1,10 +1,5 @@
-/*
- * IRQ definitions for Marvell Dove 88AP510 SoC
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
+/* SPDX-License-Identifier: GPL-2.0-only */
+/* IRQ definitions for Marvell Dove 88AP510 SoC */
 
 #ifndef __ASM_ARCH_IRQS_H
 #define __ASM_ARCH_IRQS_H
diff --git a/arch/arm/mach-dove/mpp.c b/arch/arm/mach-dove/mpp.c
index 6acd8488bb05..93cb137da5f8 100644
--- a/arch/arm/mach-dove/mpp.c
+++ b/arch/arm/mach-dove/mpp.c
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/mach-dove/mpp.c
  *
  * MPP functions for Marvell Dove SoCs
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #include <linux/kernel.h>
diff --git a/arch/arm/mach-dove/pcie.c b/arch/arm/mach-dove/pcie.c
index ee91ac6b5ebf..754ca381f600 100644
--- a/arch/arm/mach-dove/pcie.c
+++ b/arch/arm/mach-dove/pcie.c
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/mach-dove/pcie.c
  *
  * PCIe functions for Marvell Dove 88AP510 SoC
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #include <linux/kernel.h>
@@ -38,6 +35,7 @@ static int num_pcie_ports;
 static int __init dove_pcie_setup(int nr, struct pci_sys_data *sys)
 {
 	struct pcie_port *pp;
+	struct resource realio;
 
 	if (nr >= num_pcie_ports)
 		return 0;
@@ -53,10 +51,10 @@ static int __init dove_pcie_setup(int nr, struct pci_sys_data *sys)
 
 	orion_pcie_setup(pp->base);
 
-	if (pp->index == 0)
-		pci_ioremap_io(sys->busnr * SZ_64K, DOVE_PCIE0_IO_PHYS_BASE);
-	else
-		pci_ioremap_io(sys->busnr * SZ_64K, DOVE_PCIE1_IO_PHYS_BASE);
+	realio.start = sys->busnr * SZ_64K;
+	realio.end = realio.start + SZ_64K - 1;
+	pci_remap_iospace(&realio, pp->index == 0 ? DOVE_PCIE0_IO_PHYS_BASE :
+						    DOVE_PCIE1_IO_PHYS_BASE);
 
 	/*
 	 * IORESOURCE_MEM
@@ -135,14 +133,19 @@ static struct pci_ops pcie_ops = {
 	.write = pcie_wr_conf,
 };
 
+/*
+ * The root complex has a hardwired class of PCI_CLASS_MEMORY_OTHER, when it
+ * is operating as a root complex this needs to be switched to
+ * PCI_CLASS_BRIDGE_HOST or Linux will errantly try to process the BAR's on
+ * the device. Decoding setup is handled by the orion code.
+ */
 static void rc_pci_fixup(struct pci_dev *dev)
 {
-	/*
-	 * Prevent enumeration of root complex.
-	 */
 	if (dev->bus->parent == NULL && dev->devfn == 0) {
 		int i;
 
+		dev->class &= 0xff;
+		dev->class |= PCI_CLASS_BRIDGE_HOST << 8;
 		for (i = 0; i < DEVICE_COUNT_RESOURCE; i++) {
 			dev->resource[i].start = 0;
 			dev->resource[i].end   = 0;
diff --git a/arch/arm/mach-dove/pm.h b/arch/arm/mach-dove/pm.h
index 01267746d707..a4c3aba1e2d0 100644
--- a/arch/arm/mach-dove/pm.h
+++ b/arch/arm/mach-dove/pm.h
@@ -1,8 +1,4 @@
-/*
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
+/* SPDX-License-Identifier: GPL-2.0-only */
 
 #ifndef __ASM_ARCH_PM_H
 #define __ASM_ARCH_PM_H
diff --git a/arch/arm/mach-ep93xx/Kconfig b/arch/arm/mach-ep93xx/Kconfig
index 15c68a646d51..2c40996a444b 100644
--- a/arch/arm/mach-ep93xx/Kconfig
+++ b/arch/arm/mach-ep93xx/Kconfig
@@ -1,4 +1,18 @@
 # SPDX-License-Identifier: GPL-2.0-only
+menuconfig ARCH_EP93XX
+	bool "EP93xx-based"
+	depends on ATAGS
+	depends on ARCH_MULTI_V4T
+	depends on CPU_LITTLE_ENDIAN
+	select ARCH_SPARSEMEM_ENABLE
+	select ARM_AMBA
+	select ARM_VIC
+	select CLKSRC_MMIO
+	select CPU_ARM920T
+	select GPIOLIB
+	help
+	  This enables support for the Cirrus EP93xx series of CPUs.
+
 if ARCH_EP93XX
 
 menu "Cirrus EP93xx Implementation Options"
@@ -13,6 +27,7 @@ comment "EP93xx Platforms"
 
 config MACH_ADSSPHERE
 	bool "Support ADS Sphere"
+	depends on UNUSED_BOARD_FILES
 	help
 	  Say 'Y' here if you want your kernel to support the ADS
 	  Sphere board.
@@ -85,6 +100,7 @@ config MACH_EDB9315A
 
 config MACH_GESBC9312
 	bool "Support Glomation GESBC-9312-sx"
+	depends on UNUSED_BOARD_FILES
 	help
 	  Say 'Y' here if you want your kernel to support the Glomation
 	  GESBC-9312-sx board.
@@ -95,6 +111,7 @@ config MACH_MICRO9
 config MACH_MICRO9H
 	bool "Support Contec Micro9-High"
 	select MACH_MICRO9
+	depends on UNUSED_BOARD_FILES
 	help
 	  Say 'Y' here if you want your kernel to support the
 	  Contec Micro9-High board.
@@ -102,6 +119,7 @@ config MACH_MICRO9H
 config MACH_MICRO9M
 	bool "Support Contec Micro9-Mid"
 	select MACH_MICRO9
+	depends on UNUSED_BOARD_FILES
 	help
 	  Say 'Y' here if you want your kernel to support the
 	  Contec Micro9-Mid board.
@@ -109,6 +127,7 @@ config MACH_MICRO9M
 config MACH_MICRO9L
 	bool "Support Contec Micro9-Lite"
 	select MACH_MICRO9
+	depends on UNUSED_BOARD_FILES
 	help
 	  Say 'Y' here if you want your kernel to support the
 	  Contec Micro9-Lite board.
@@ -116,18 +135,21 @@ config MACH_MICRO9L
 config MACH_MICRO9S
 	bool "Support Contec Micro9-Slim"
 	select MACH_MICRO9
+	depends on UNUSED_BOARD_FILES
 	help
 	  Say 'Y' here if you want your kernel to support the
 	  Contec Micro9-Slim board.
 
 config MACH_SIM_ONE
         bool "Support Simplemachines Sim.One board"
+	depends on UNUSED_BOARD_FILES
         help
           Say 'Y' here if you want your kernel to support the
           Simplemachines Sim.One board.
 
 config MACH_SNAPPER_CL15
 	bool "Support Bluewater Systems Snapper CL15 Module"
+	depends on UNUSED_BOARD_FILES
 	help
 	  Say 'Y' here if you want your kernel to support the Bluewater
 	  Systems Snapper CL15 Module.
diff --git a/arch/arm/mach-ep93xx/Makefile.boot b/arch/arm/mach-ep93xx/Makefile.boot
deleted file mode 100644
index 4c0a039a5027..000000000000
--- a/arch/arm/mach-ep93xx/Makefile.boot
+++ /dev/null
@@ -1,2 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0-only
-# Empty file waiting for deletion once Makefile.boot isn't needed any more.
diff --git a/arch/arm/mach-ep93xx/adssphere.c b/arch/arm/mach-ep93xx/adssphere.c
index 8d5e349a7a6d..0c48d3c5b8e7 100644
--- a/arch/arm/mach-ep93xx/adssphere.c
+++ b/arch/arm/mach-ep93xx/adssphere.c
@@ -32,6 +32,7 @@ static void __init adssphere_init_machine(void)
 MACHINE_START(ADSSPHERE, "ADS Sphere board")
 	/* Maintainer: Lennert Buytenhek <buytenh@wantstofly.org> */
 	.atag_offset	= 0x100,
+	.nr_irqs	= NR_EP93XX_IRQS,
 	.map_io		= ep93xx_map_io,
 	.init_irq	= ep93xx_init_irq,
 	.init_time	= ep93xx_timer_init,
diff --git a/arch/arm/mach-ep93xx/clock.c b/arch/arm/mach-ep93xx/clock.c
index cc75087134d3..85a496ddc619 100644
--- a/arch/arm/mach-ep93xx/clock.c
+++ b/arch/arm/mach-ep93xx/clock.c
@@ -148,8 +148,10 @@ static struct clk_hw *ep93xx_clk_register_gate(const char *name,
 	psc->lock = &clk_lock;
 
 	clk = clk_register(NULL, &psc->hw);
-	if (IS_ERR(clk))
+	if (IS_ERR(clk)) {
 		kfree(psc);
+		return ERR_CAST(clk);
+	}
 
 	return &psc->hw;
 }
@@ -207,7 +209,7 @@ static int ep93xx_mux_determine_rate(struct clk_hw *hw,
 				struct clk_rate_request *req)
 {
 	unsigned long rate = req->rate;
-	struct clk *best_parent = 0;
+	struct clk *best_parent = NULL;
 	unsigned long __parent_rate;
 	unsigned long best_rate = 0, actual_rate, mclk_rate;
 	unsigned long best_parent_rate;
@@ -343,9 +345,10 @@ static struct clk_hw *clk_hw_register_ddiv(const char *name,
 	psc->hw.init = &init;
 
 	clk = clk_register(NULL, &psc->hw);
-	if (IS_ERR(clk))
+	if (IS_ERR(clk)) {
 		kfree(psc);
-
+		return ERR_CAST(clk);
+	}
 	return &psc->hw;
 }
 
@@ -450,9 +453,10 @@ static struct clk_hw *clk_hw_register_div(const char *name,
 	psc->hw.init = &init;
 
 	clk = clk_register(NULL, &psc->hw);
-	if (IS_ERR(clk))
+	if (IS_ERR(clk)) {
 		kfree(psc);
-
+		return ERR_CAST(clk);
+	}
 	return &psc->hw;
 }
 
diff --git a/arch/arm/mach-ep93xx/core.c b/arch/arm/mach-ep93xx/core.c
index a3b4e843456a..95e731676cea 100644
--- a/arch/arm/mach-ep93xx/core.c
+++ b/arch/arm/mach-ep93xx/core.c
@@ -22,6 +22,7 @@
 #include <linux/io.h>
 #include <linux/gpio.h>
 #include <linux/leds.h>
+#include <linux/uaccess.h>
 #include <linux/termios.h>
 #include <linux/amba/bus.h>
 #include <linux/amba/serial.h>
@@ -47,6 +48,7 @@
 #include <asm/mach/map.h>
 
 #include "soc.h"
+#include "irqs.h"
 
 /*************************************************************************
  * Static I/O mappings that are needed for all EP93xx platforms
@@ -75,8 +77,8 @@ void __init ep93xx_map_io(void)
  *************************************************************************/
 void __init ep93xx_init_irq(void)
 {
-	vic_init(EP93XX_VIC1_BASE, 0, EP93XX_VIC1_VALID_IRQ_MASK, 0);
-	vic_init(EP93XX_VIC2_BASE, 32, EP93XX_VIC2_VALID_IRQ_MASK, 0);
+	vic_init(EP93XX_VIC1_BASE, IRQ_EP93XX_VIC0, EP93XX_VIC1_VALID_IRQ_MASK, 0);
+	vic_init(EP93XX_VIC2_BASE, IRQ_EP93XX_VIC1, EP93XX_VIC2_VALID_IRQ_MASK, 0);
 }
 
 
diff --git a/arch/arm/mach-ep93xx/edb93xx.c b/arch/arm/mach-ep93xx/edb93xx.c
index af0e22471ebd..4b90899a66e9 100644
--- a/arch/arm/mach-ep93xx/edb93xx.c
+++ b/arch/arm/mach-ep93xx/edb93xx.c
@@ -243,6 +243,7 @@ static void __init edb93xx_init_machine(void)
 MACHINE_START(EDB9301, "Cirrus Logic EDB9301 Evaluation Board")
 	/* Maintainer: H Hartley Sweeten <hsweeten@visionengravers.com> */
 	.atag_offset	= 0x100,
+	.nr_irqs	= NR_EP93XX_IRQS,
 	.map_io		= ep93xx_map_io,
 	.init_irq	= ep93xx_init_irq,
 	.init_time	= ep93xx_timer_init,
@@ -255,6 +256,7 @@ MACHINE_END
 MACHINE_START(EDB9302, "Cirrus Logic EDB9302 Evaluation Board")
 	/* Maintainer: George Kashperko <george@chas.com.ua> */
 	.atag_offset	= 0x100,
+	.nr_irqs	= NR_EP93XX_IRQS,
 	.map_io		= ep93xx_map_io,
 	.init_irq	= ep93xx_init_irq,
 	.init_time	= ep93xx_timer_init,
@@ -267,6 +269,7 @@ MACHINE_END
 MACHINE_START(EDB9302A, "Cirrus Logic EDB9302A Evaluation Board")
 	/* Maintainer: Lennert Buytenhek <buytenh@wantstofly.org> */
 	.atag_offset	= 0x100,
+	.nr_irqs	= NR_EP93XX_IRQS,
 	.map_io		= ep93xx_map_io,
 	.init_irq	= ep93xx_init_irq,
 	.init_time	= ep93xx_timer_init,
@@ -279,6 +282,7 @@ MACHINE_END
 MACHINE_START(EDB9307, "Cirrus Logic EDB9307 Evaluation Board")
 	/* Maintainer: Herbert Valerio Riedel <hvr@gnu.org> */
 	.atag_offset	= 0x100,
+	.nr_irqs	= NR_EP93XX_IRQS,
 	.map_io		= ep93xx_map_io,
 	.init_irq	= ep93xx_init_irq,
 	.init_time	= ep93xx_timer_init,
@@ -291,6 +295,7 @@ MACHINE_END
 MACHINE_START(EDB9307A, "Cirrus Logic EDB9307A Evaluation Board")
 	/* Maintainer: H Hartley Sweeten <hsweeten@visionengravers.com> */
 	.atag_offset	= 0x100,
+	.nr_irqs	= NR_EP93XX_IRQS,
 	.map_io		= ep93xx_map_io,
 	.init_irq	= ep93xx_init_irq,
 	.init_time	= ep93xx_timer_init,
@@ -303,6 +308,7 @@ MACHINE_END
 MACHINE_START(EDB9312, "Cirrus Logic EDB9312 Evaluation Board")
 	/* Maintainer: Toufeeq Hussain <toufeeq_hussain@infosys.com> */
 	.atag_offset	= 0x100,
+	.nr_irqs	= NR_EP93XX_IRQS,
 	.map_io		= ep93xx_map_io,
 	.init_irq	= ep93xx_init_irq,
 	.init_time	= ep93xx_timer_init,
@@ -315,6 +321,7 @@ MACHINE_END
 MACHINE_START(EDB9315, "Cirrus Logic EDB9315 Evaluation Board")
 	/* Maintainer: Lennert Buytenhek <buytenh@wantstofly.org> */
 	.atag_offset	= 0x100,
+	.nr_irqs	= NR_EP93XX_IRQS,
 	.map_io		= ep93xx_map_io,
 	.init_irq	= ep93xx_init_irq,
 	.init_time	= ep93xx_timer_init,
@@ -327,6 +334,7 @@ MACHINE_END
 MACHINE_START(EDB9315A, "Cirrus Logic EDB9315A Evaluation Board")
 	/* Maintainer: Lennert Buytenhek <buytenh@wantstofly.org> */
 	.atag_offset	= 0x100,
+	.nr_irqs	= NR_EP93XX_IRQS,
 	.map_io		= ep93xx_map_io,
 	.init_irq	= ep93xx_init_irq,
 	.init_time	= ep93xx_timer_init,
diff --git a/arch/arm/mach-ep93xx/include/mach/ep93xx-regs.h b/arch/arm/mach-ep93xx/ep93xx-regs.h
index 6839ea032e58..8fa3646de0a4 100644
--- a/arch/arm/mach-ep93xx/include/mach/ep93xx-regs.h
+++ b/arch/arm/mach-ep93xx/ep93xx-regs.h
@@ -1,8 +1,4 @@
 /* SPDX-License-Identifier: GPL-2.0 */
-/*
- * arch/arm/mach-ep93xx/include/mach/ep93xx-regs.h
- */
-
 #ifndef __ASM_ARCH_EP93XX_REGS_H
 #define __ASM_ARCH_EP93XX_REGS_H
 
diff --git a/arch/arm/mach-ep93xx/gesbc9312.c b/arch/arm/mach-ep93xx/gesbc9312.c
index d7f9890321eb..0b7043e3e178 100644
--- a/arch/arm/mach-ep93xx/gesbc9312.c
+++ b/arch/arm/mach-ep93xx/gesbc9312.c
@@ -32,6 +32,7 @@ static void __init gesbc9312_init_machine(void)
 MACHINE_START(GESBC9312, "Glomation GESBC-9312-sx")
 	/* Maintainer: Lennert Buytenhek <buytenh@wantstofly.org> */
 	.atag_offset	= 0x100,
+	.nr_irqs	= NR_EP93XX_IRQS,
 	.map_io		= ep93xx_map_io,
 	.init_irq	= ep93xx_init_irq,
 	.init_time	= ep93xx_timer_init,
diff --git a/arch/arm/mach-ep93xx/gpio-ep93xx.h b/arch/arm/mach-ep93xx/gpio-ep93xx.h
index 242af4a401ea..7b46eb7e5507 100644
--- a/arch/arm/mach-ep93xx/gpio-ep93xx.h
+++ b/arch/arm/mach-ep93xx/gpio-ep93xx.h
@@ -4,7 +4,7 @@
 #ifndef __GPIO_EP93XX_H
 #define __GPIO_EP93XX_H
 
-#include <mach/ep93xx-regs.h>
+#include "ep93xx-regs.h"
 
 #define EP93XX_GPIO_PHYS_BASE		EP93XX_APB_PHYS(0x00040000)
 #define EP93XX_GPIO_BASE		EP93XX_APB_IOMEM(0x00040000)
diff --git a/arch/arm/mach-ep93xx/include/mach/irqs.h b/arch/arm/mach-ep93xx/include/mach/irqs.h
deleted file mode 100644
index 244daf83ce6d..000000000000
--- a/arch/arm/mach-ep93xx/include/mach/irqs.h
+++ /dev/null
@@ -1,79 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-/*
- * arch/arm/mach-ep93xx/include/mach/irqs.h
- */
-
-#ifndef __ASM_ARCH_IRQS_H
-#define __ASM_ARCH_IRQS_H
-
-#define IRQ_EP93XX_COMMRX		2
-#define IRQ_EP93XX_COMMTX		3
-#define IRQ_EP93XX_TIMER1		4
-#define IRQ_EP93XX_TIMER2		5
-#define IRQ_EP93XX_AACINTR		6
-#define IRQ_EP93XX_DMAM2P0		7
-#define IRQ_EP93XX_DMAM2P1		8
-#define IRQ_EP93XX_DMAM2P2		9
-#define IRQ_EP93XX_DMAM2P3		10
-#define IRQ_EP93XX_DMAM2P4		11
-#define IRQ_EP93XX_DMAM2P5		12
-#define IRQ_EP93XX_DMAM2P6		13
-#define IRQ_EP93XX_DMAM2P7		14
-#define IRQ_EP93XX_DMAM2P8		15
-#define IRQ_EP93XX_DMAM2P9		16
-#define IRQ_EP93XX_DMAM2M0		17
-#define IRQ_EP93XX_DMAM2M1		18
-#define IRQ_EP93XX_GPIO0MUX		19
-#define IRQ_EP93XX_GPIO1MUX		20
-#define IRQ_EP93XX_GPIO2MUX		21
-#define IRQ_EP93XX_GPIO3MUX		22
-#define IRQ_EP93XX_UART1RX		23
-#define IRQ_EP93XX_UART1TX		24
-#define IRQ_EP93XX_UART2RX		25
-#define IRQ_EP93XX_UART2TX		26
-#define IRQ_EP93XX_UART3RX		27
-#define IRQ_EP93XX_UART3TX		28
-#define IRQ_EP93XX_KEY			29
-#define IRQ_EP93XX_TOUCH		30
-#define EP93XX_VIC1_VALID_IRQ_MASK	0x7ffffffc
-
-#define IRQ_EP93XX_EXT0			32
-#define IRQ_EP93XX_EXT1			33
-#define IRQ_EP93XX_EXT2			34
-#define IRQ_EP93XX_64HZ			35
-#define IRQ_EP93XX_WATCHDOG		36
-#define IRQ_EP93XX_RTC			37
-#define IRQ_EP93XX_IRDA			38
-#define IRQ_EP93XX_ETHERNET		39
-#define IRQ_EP93XX_EXT3			40
-#define IRQ_EP93XX_PROG			41
-#define IRQ_EP93XX_1HZ			42
-#define IRQ_EP93XX_VSYNC		43
-#define IRQ_EP93XX_VIDEO_FIFO		44
-#define IRQ_EP93XX_SSP1RX		45
-#define IRQ_EP93XX_SSP1TX		46
-#define IRQ_EP93XX_GPIO4MUX		47
-#define IRQ_EP93XX_GPIO5MUX		48
-#define IRQ_EP93XX_GPIO6MUX		49
-#define IRQ_EP93XX_GPIO7MUX		50
-#define IRQ_EP93XX_TIMER3		51
-#define IRQ_EP93XX_UART1		52
-#define IRQ_EP93XX_SSP			53
-#define IRQ_EP93XX_UART2		54
-#define IRQ_EP93XX_UART3		55
-#define IRQ_EP93XX_USB			56
-#define IRQ_EP93XX_ETHERNET_PME		57
-#define IRQ_EP93XX_DSP			58
-#define IRQ_EP93XX_GPIO_AB		59
-#define IRQ_EP93XX_SAI			60
-#define EP93XX_VIC2_VALID_IRQ_MASK	0x1fffffff
-
-#define NR_EP93XX_IRQS			(64 + 24)
-
-#define EP93XX_BOARD_IRQ(x)		(NR_EP93XX_IRQS + (x))
-#define EP93XX_BOARD_IRQS		32
-
-#define NR_IRQS				(NR_EP93XX_IRQS + EP93XX_BOARD_IRQS)
-
-
-#endif
diff --git a/arch/arm/mach-ep93xx/include/mach/uncompress.h b/arch/arm/mach-ep93xx/include/mach/uncompress.h
deleted file mode 100644
index b3ec1db988db..000000000000
--- a/arch/arm/mach-ep93xx/include/mach/uncompress.h
+++ /dev/null
@@ -1,90 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-or-later */
-/*
- * arch/arm/mach-ep93xx/include/mach/uncompress.h
- *
- * Copyright (C) 2006 Lennert Buytenhek <buytenh@wantstofly.org>
- */
-
-#include <mach/ep93xx-regs.h>
-#include <asm/mach-types.h>
-
-static unsigned char __raw_readb(unsigned int ptr)
-{
-	return *((volatile unsigned char *)ptr);
-}
-
-static unsigned int __raw_readl(unsigned int ptr)
-{
-	return *((volatile unsigned int *)ptr);
-}
-
-static void __raw_writeb(unsigned char value, unsigned int ptr)
-{
-	*((volatile unsigned char *)ptr) = value;
-}
-
-static void __raw_writel(unsigned int value, unsigned int ptr)
-{
-	*((volatile unsigned int *)ptr) = value;
-}
-
-#define PHYS_UART_DATA		(CONFIG_DEBUG_UART_PHYS + 0x00)
-#define PHYS_UART_FLAG		(CONFIG_DEBUG_UART_PHYS + 0x18)
-#define UART_FLAG_TXFF		0x20
-
-static inline void putc(int c)
-{
-	int i;
-
-	for (i = 0; i < 10000; i++) {
-		/* Transmit fifo not full? */
-		if (!(__raw_readb(PHYS_UART_FLAG) & UART_FLAG_TXFF))
-			break;
-	}
-
-	__raw_writeb(c, PHYS_UART_DATA);
-}
-
-static inline void flush(void)
-{
-}
-
-
-/*
- * Some bootloaders don't turn off DMA from the ethernet MAC before
- * jumping to linux, which means that we might end up with bits of RX
- * status and packet data scribbled over the uncompressed kernel image.
- * Work around this by resetting the ethernet MAC before we uncompress.
- */
-#define PHYS_ETH_SELF_CTL		0x80010020
-#define ETH_SELF_CTL_RESET		0x00000001
-
-static void ethernet_reset(void)
-{
-	unsigned int v;
-
-	/* Reset the ethernet MAC.  */
-	v = __raw_readl(PHYS_ETH_SELF_CTL);
-	__raw_writel(v | ETH_SELF_CTL_RESET, PHYS_ETH_SELF_CTL);
-
-	/* Wait for reset to finish.  */
-	while (__raw_readl(PHYS_ETH_SELF_CTL) & ETH_SELF_CTL_RESET)
-		;
-}
-
-#define TS72XX_WDT_CONTROL_PHYS_BASE	0x23800000
-#define TS72XX_WDT_FEED_PHYS_BASE	0x23c00000
-#define TS72XX_WDT_FEED_VAL		0x05
-
-static void __maybe_unused ts72xx_watchdog_disable(void)
-{
-	__raw_writeb(TS72XX_WDT_FEED_VAL, TS72XX_WDT_FEED_PHYS_BASE);
-	__raw_writeb(0, TS72XX_WDT_CONTROL_PHYS_BASE);
-}
-
-static void arch_decomp_setup(void)
-{
-	if (machine_is_ts72xx())
-		ts72xx_watchdog_disable();
-	ethernet_reset();
-}
diff --git a/arch/arm/mach-ep93xx/irqs.h b/arch/arm/mach-ep93xx/irqs.h
new file mode 100644
index 000000000000..353201b90c66
--- /dev/null
+++ b/arch/arm/mach-ep93xx/irqs.h
@@ -0,0 +1,76 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __ASM_ARCH_IRQS_H
+#define __ASM_ARCH_IRQS_H
+
+#define IRQ_EP93XX_VIC0			1
+
+#define IRQ_EP93XX_COMMRX		(IRQ_EP93XX_VIC0 + 2)
+#define IRQ_EP93XX_COMMTX		(IRQ_EP93XX_VIC0 + 3)
+#define IRQ_EP93XX_TIMER1		(IRQ_EP93XX_VIC0 + 4)
+#define IRQ_EP93XX_TIMER2		(IRQ_EP93XX_VIC0 + 5)
+#define IRQ_EP93XX_AACINTR		(IRQ_EP93XX_VIC0 + 6)
+#define IRQ_EP93XX_DMAM2P0		(IRQ_EP93XX_VIC0 + 7)
+#define IRQ_EP93XX_DMAM2P1		(IRQ_EP93XX_VIC0 + 8)
+#define IRQ_EP93XX_DMAM2P2		(IRQ_EP93XX_VIC0 + 9)
+#define IRQ_EP93XX_DMAM2P3		(IRQ_EP93XX_VIC0 + 10)
+#define IRQ_EP93XX_DMAM2P4		(IRQ_EP93XX_VIC0 + 11)
+#define IRQ_EP93XX_DMAM2P5		(IRQ_EP93XX_VIC0 + 12)
+#define IRQ_EP93XX_DMAM2P6		(IRQ_EP93XX_VIC0 + 13)
+#define IRQ_EP93XX_DMAM2P7		(IRQ_EP93XX_VIC0 + 14)
+#define IRQ_EP93XX_DMAM2P8		(IRQ_EP93XX_VIC0 + 15)
+#define IRQ_EP93XX_DMAM2P9		(IRQ_EP93XX_VIC0 + 16)
+#define IRQ_EP93XX_DMAM2M0		(IRQ_EP93XX_VIC0 + 17)
+#define IRQ_EP93XX_DMAM2M1		(IRQ_EP93XX_VIC0 + 18)
+#define IRQ_EP93XX_GPIO0MUX		(IRQ_EP93XX_VIC0 + 19)
+#define IRQ_EP93XX_GPIO1MUX		(IRQ_EP93XX_VIC0 + 20)
+#define IRQ_EP93XX_GPIO2MUX		(IRQ_EP93XX_VIC0 + 21)
+#define IRQ_EP93XX_GPIO3MUX		(IRQ_EP93XX_VIC0 + 22)
+#define IRQ_EP93XX_UART1RX		(IRQ_EP93XX_VIC0 + 23)
+#define IRQ_EP93XX_UART1TX		(IRQ_EP93XX_VIC0 + 24)
+#define IRQ_EP93XX_UART2RX		(IRQ_EP93XX_VIC0 + 25)
+#define IRQ_EP93XX_UART2TX		(IRQ_EP93XX_VIC0 + 26)
+#define IRQ_EP93XX_UART3RX		(IRQ_EP93XX_VIC0 + 27)
+#define IRQ_EP93XX_UART3TX		(IRQ_EP93XX_VIC0 + 28)
+#define IRQ_EP93XX_KEY			(IRQ_EP93XX_VIC0 + 29)
+#define IRQ_EP93XX_TOUCH		(IRQ_EP93XX_VIC0 + 30)
+#define EP93XX_VIC1_VALID_IRQ_MASK	0x7ffffffc
+
+#define IRQ_EP93XX_VIC1			(IRQ_EP93XX_VIC0 + 32)
+
+#define IRQ_EP93XX_EXT0			(IRQ_EP93XX_VIC1 + 0)
+#define IRQ_EP93XX_EXT1			(IRQ_EP93XX_VIC1 + 1)
+#define IRQ_EP93XX_EXT2			(IRQ_EP93XX_VIC1 + 2)
+#define IRQ_EP93XX_64HZ			(IRQ_EP93XX_VIC1 + 3)
+#define IRQ_EP93XX_WATCHDOG		(IRQ_EP93XX_VIC1 + 4)
+#define IRQ_EP93XX_RTC			(IRQ_EP93XX_VIC1 + 5)
+#define IRQ_EP93XX_IRDA			(IRQ_EP93XX_VIC1 + 6)
+#define IRQ_EP93XX_ETHERNET		(IRQ_EP93XX_VIC1 + 7)
+#define IRQ_EP93XX_EXT3			(IRQ_EP93XX_VIC1 + 8)
+#define IRQ_EP93XX_PROG			(IRQ_EP93XX_VIC1 + 9)
+#define IRQ_EP93XX_1HZ			(IRQ_EP93XX_VIC1 + 10)
+#define IRQ_EP93XX_VSYNC		(IRQ_EP93XX_VIC1 + 11)
+#define IRQ_EP93XX_VIDEO_FIFO		(IRQ_EP93XX_VIC1 + 12)
+#define IRQ_EP93XX_SSP1RX		(IRQ_EP93XX_VIC1 + 13)
+#define IRQ_EP93XX_SSP1TX		(IRQ_EP93XX_VIC1 + 14)
+#define IRQ_EP93XX_GPIO4MUX		(IRQ_EP93XX_VIC1 + 15)
+#define IRQ_EP93XX_GPIO5MUX		(IRQ_EP93XX_VIC1 + 16)
+#define IRQ_EP93XX_GPIO6MUX		(IRQ_EP93XX_VIC1 + 17)
+#define IRQ_EP93XX_GPIO7MUX		(IRQ_EP93XX_VIC1 + 18)
+#define IRQ_EP93XX_TIMER3		(IRQ_EP93XX_VIC1 + 19)
+#define IRQ_EP93XX_UART1		(IRQ_EP93XX_VIC1 + 20)
+#define IRQ_EP93XX_SSP			(IRQ_EP93XX_VIC1 + 21)
+#define IRQ_EP93XX_UART2		(IRQ_EP93XX_VIC1 + 22)
+#define IRQ_EP93XX_UART3		(IRQ_EP93XX_VIC1 + 23)
+#define IRQ_EP93XX_USB			(IRQ_EP93XX_VIC1 + 24)
+#define IRQ_EP93XX_ETHERNET_PME		(IRQ_EP93XX_VIC1 + 25)
+#define IRQ_EP93XX_DSP			(IRQ_EP93XX_VIC1 + 26)
+#define IRQ_EP93XX_GPIO_AB		(IRQ_EP93XX_VIC1 + 27)
+#define IRQ_EP93XX_SAI			(IRQ_EP93XX_VIC1 + 28)
+#define EP93XX_VIC2_VALID_IRQ_MASK	0x1fffffff
+
+#define NR_EP93XX_IRQS			(IRQ_EP93XX_VIC1 + 32 + 24)
+
+#define EP93XX_BOARD_IRQ(x)		(NR_EP93XX_IRQS + (x))
+#define EP93XX_BOARD_IRQS		32
+
+#endif
diff --git a/arch/arm/mach-ep93xx/micro9.c b/arch/arm/mach-ep93xx/micro9.c
index e6ead8ded6ee..c121c459aa17 100644
--- a/arch/arm/mach-ep93xx/micro9.c
+++ b/arch/arm/mach-ep93xx/micro9.c
@@ -76,6 +76,7 @@ static void __init micro9_init_machine(void)
 MACHINE_START(MICRO9, "Contec Micro9-High")
 	/* Maintainer: Hubert Feurstein <hubert.feurstein@contec.at> */
 	.atag_offset	= 0x100,
+	.nr_irqs	= NR_EP93XX_IRQS,
 	.map_io		= ep93xx_map_io,
 	.init_irq	= ep93xx_init_irq,
 	.init_time	= ep93xx_timer_init,
@@ -88,6 +89,7 @@ MACHINE_END
 MACHINE_START(MICRO9M, "Contec Micro9-Mid")
 	/* Maintainer: Hubert Feurstein <hubert.feurstein@contec.at> */
 	.atag_offset	= 0x100,
+	.nr_irqs	= NR_EP93XX_IRQS,
 	.map_io		= ep93xx_map_io,
 	.init_irq	= ep93xx_init_irq,
 	.init_time	= ep93xx_timer_init,
@@ -100,6 +102,7 @@ MACHINE_END
 MACHINE_START(MICRO9L, "Contec Micro9-Lite")
 	/* Maintainer: Hubert Feurstein <hubert.feurstein@contec.at> */
 	.atag_offset	= 0x100,
+	.nr_irqs	= NR_EP93XX_IRQS,
 	.map_io		= ep93xx_map_io,
 	.init_irq	= ep93xx_init_irq,
 	.init_time	= ep93xx_timer_init,
@@ -112,6 +115,7 @@ MACHINE_END
 MACHINE_START(MICRO9S, "Contec Micro9-Slim")
 	/* Maintainer: Hubert Feurstein <hubert.feurstein@contec.at> */
 	.atag_offset	= 0x100,
+	.nr_irqs	= NR_EP93XX_IRQS,
 	.map_io		= ep93xx_map_io,
 	.init_irq	= ep93xx_init_irq,
 	.init_time	= ep93xx_timer_init,
diff --git a/arch/arm/mach-ep93xx/simone.c b/arch/arm/mach-ep93xx/simone.c
index 5291053023b2..569e72413561 100644
--- a/arch/arm/mach-ep93xx/simone.c
+++ b/arch/arm/mach-ep93xx/simone.c
@@ -119,6 +119,7 @@ static void __init simone_init_machine(void)
 MACHINE_START(SIM_ONE, "Simplemachines Sim.One Board")
 	/* Maintainer: Ryan Mallon */
 	.atag_offset	= 0x100,
+	.nr_irqs	= NR_EP93XX_IRQS,
 	.map_io		= ep93xx_map_io,
 	.init_irq	= ep93xx_init_irq,
 	.init_time	= ep93xx_timer_init,
diff --git a/arch/arm/mach-ep93xx/snappercl15.c b/arch/arm/mach-ep93xx/snappercl15.c
index e200d69471e9..1dfb725671b1 100644
--- a/arch/arm/mach-ep93xx/snappercl15.c
+++ b/arch/arm/mach-ep93xx/snappercl15.c
@@ -153,6 +153,7 @@ static void __init snappercl15_init_machine(void)
 MACHINE_START(SNAPPER_CL15, "Bluewater Systems Snapper CL15")
 	/* Maintainer: Ryan Mallon */
 	.atag_offset	= 0x100,
+	.nr_irqs	= NR_EP93XX_IRQS,
 	.map_io		= ep93xx_map_io,
 	.init_irq	= ep93xx_init_irq,
 	.init_time	= ep93xx_timer_init,
diff --git a/arch/arm/mach-ep93xx/soc.h b/arch/arm/mach-ep93xx/soc.h
index 94ef7f275f94..3245ebbd5069 100644
--- a/arch/arm/mach-ep93xx/soc.h
+++ b/arch/arm/mach-ep93xx/soc.h
@@ -9,7 +9,8 @@
 #ifndef _EP93XX_SOC_H
 #define _EP93XX_SOC_H
 
-#include <mach/ep93xx-regs.h>
+#include "ep93xx-regs.h"
+#include "irqs.h"
 
 /*
  * EP93xx Physical Memory Map:
diff --git a/arch/arm/mach-ep93xx/ts72xx.c b/arch/arm/mach-ep93xx/ts72xx.c
index 12eff8c8074d..d3de7283ecb3 100644
--- a/arch/arm/mach-ep93xx/ts72xx.c
+++ b/arch/arm/mach-ep93xx/ts72xx.c
@@ -22,7 +22,6 @@
 
 #include "gpio-ep93xx.h"
 #include "hardware.h"
-#include <mach/irqs.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/map.h>
@@ -151,7 +150,7 @@ static struct platform_device ts72xx_nand_flash = {
 	.num_resources		= ARRAY_SIZE(ts72xx_nand_resource),
 };
 
-void __init ts72xx_register_flash(struct mtd_partition *parts, int n,
+static void __init ts72xx_register_flash(struct mtd_partition *parts, int n,
 				  resource_size_t start)
 {
 	/*
@@ -350,6 +349,7 @@ static void __init ts72xx_init_machine(void)
 MACHINE_START(TS72XX, "Technologic Systems TS-72xx SBC")
 	/* Maintainer: Lennert Buytenhek <buytenh@wantstofly.org> */
 	.atag_offset	= 0x100,
+	.nr_irqs	= NR_EP93XX_IRQS,
 	.map_io		= ts72xx_map_io,
 	.init_irq	= ep93xx_init_irq,
 	.init_time	= ep93xx_timer_init,
@@ -413,6 +413,7 @@ static void __init bk3_init_machine(void)
 MACHINE_START(BK3, "Liebherr controller BK3.1")
 	/* Maintainer: Lukasz Majewski <lukma@denx.de> */
 	.atag_offset	= 0x100,
+	.nr_irqs	= NR_EP93XX_IRQS,
 	.map_io		= ts72xx_map_io,
 	.init_irq	= ep93xx_init_irq,
 	.init_time	= ep93xx_timer_init,
diff --git a/arch/arm/mach-ep93xx/vision_ep9307.c b/arch/arm/mach-ep93xx/vision_ep9307.c
index e46281e60bf7..30d9cf3791eb 100644
--- a/arch/arm/mach-ep93xx/vision_ep9307.c
+++ b/arch/arm/mach-ep93xx/vision_ep9307.c
@@ -302,6 +302,7 @@ static void __init vision_init_machine(void)
 MACHINE_START(VISION_EP9307, "Vision Engraving Systems EP9307")
 	/* Maintainer: H Hartley Sweeten <hsweeten@visionengravers.com> */
 	.atag_offset	= 0x100,
+	.nr_irqs	= NR_EP93XX_IRQS + EP93XX_BOARD_IRQS,
 	.map_io		= vision_map_io,
 	.init_irq	= ep93xx_init_irq,
 	.init_time	= ep93xx_timer_init,
diff --git a/arch/arm/mach-exynos/Kconfig b/arch/arm/mach-exynos/Kconfig
index dd1ae5571f43..4d3b40e4049a 100644
--- a/arch/arm/mach-exynos/Kconfig
+++ b/arch/arm/mach-exynos/Kconfig
@@ -8,7 +8,6 @@
 menuconfig ARCH_EXYNOS
 	bool "Samsung Exynos"
 	depends on ARCH_MULTI_V7
-	select ARCH_SUPPORTS_BIG_ENDIAN
 	select ARM_AMBA
 	select ARM_GIC
 	select EXYNOS_IRQ_COMBINER
@@ -17,10 +16,8 @@ menuconfig ARCH_EXYNOS
 	select EXYNOS_PMU
 	select EXYNOS_SROM
 	select EXYNOS_PM_DOMAINS if PM_GENERIC_DOMAINS
-	select GPIOLIB
 	select HAVE_ARM_ARCH_TIMER if ARCH_EXYNOS5
 	select HAVE_ARM_SCU if SMP
-	select HAVE_S3C2410_I2C if I2C
 	select PINCTRL
 	select PINCTRL_EXYNOS
 	select PM_GENERIC_DOMAINS if PM
diff --git a/arch/arm/mach-exynos/exynos.c b/arch/arm/mach-exynos/exynos.c
index 8b48326be9fd..51a247ca4da8 100644
--- a/arch/arm/mach-exynos/exynos.c
+++ b/arch/arm/mach-exynos/exynos.c
@@ -149,6 +149,7 @@ static void exynos_map_pmu(void)
 	np = of_find_matching_node(NULL, exynos_dt_pmu_match);
 	if (np)
 		pmu_base_addr = of_iomap(np, 0);
+	of_node_put(np);
 }
 
 static void __init exynos_init_irq(void)
diff --git a/arch/arm/mach-exynos/firmware.c b/arch/arm/mach-exynos/firmware.c
index 2eaf2dbb8e81..2da5b60b59e2 100644
--- a/arch/arm/mach-exynos/firmware.c
+++ b/arch/arm/mach-exynos/firmware.c
@@ -60,8 +60,10 @@ static int exynos_cpu_boot(int cpu)
 	/*
 	 * Exynos3250 doesn't need to send smc command for secondary CPU boot
 	 * because Exynos3250 removes WFE in secure mode.
+	 *
+	 * On Exynos5 devices the call is ignored by trustzone firmware.
 	 */
-	if (soc_is_exynos3250())
+	if (!soc_is_exynos4210() && !soc_is_exynos4412())
 		return 0;
 
 	/*
diff --git a/arch/arm/mach-exynos/mcpm-exynos.c b/arch/arm/mach-exynos/mcpm-exynos.c
index cd861c57d5ad..fd0dbeb93357 100644
--- a/arch/arm/mach-exynos/mcpm-exynos.c
+++ b/arch/arm/mach-exynos/mcpm-exynos.c
@@ -35,7 +35,6 @@ static bool secure_firmware __ro_after_init;
  */
 #define exynos_v7_exit_coherency_flush(level) \
 	asm volatile( \
-	"stmfd	sp!, {fp, ip}\n\t"\
 	"mrc	p15, 0, r0, c1, c0, 0	@ get SCTLR\n\t" \
 	"bic	r0, r0, #"__stringify(CR_C)"\n\t" \
 	"mcr	p15, 0, r0, c1, c0, 0	@ set SCTLR\n\t" \
@@ -50,11 +49,10 @@ static bool secure_firmware __ro_after_init;
 	"mcr	p15, 0, r0, c1, c0, 1	@ set ACTLR\n\t" \
 	"isb\n\t" \
 	"dsb\n\t" \
-	"ldmfd	sp!, {fp, ip}" \
 	: \
 	: "Ir" (pmu_base_addr + S5P_INFORM0) \
-	: "r0", "r1", "r2", "r3", "r4", "r5", "r6", "r7", \
-	  "r9", "r10", "lr", "memory")
+	: "r0", "r1", "r2", "r3", "r4", "r5", "r6", \
+	  "r9", "r10", "ip", "lr", "memory")
 
 static int exynos_cpu_powerup(unsigned int cpu, unsigned int cluster)
 {
diff --git a/arch/arm/mach-footbridge/Kconfig b/arch/arm/mach-footbridge/Kconfig
index 728aff93fba9..b5e7cbfed119 100644
--- a/arch/arm/mach-footbridge/Kconfig
+++ b/arch/arm/mach-footbridge/Kconfig
@@ -1,37 +1,37 @@
 # SPDX-License-Identifier: GPL-2.0-only
-if ARCH_FOOTBRIDGE
+menuconfig ARCH_FOOTBRIDGE
+	bool "FootBridge Implementations"
+	depends on ARCH_MULTI_V4 && !(ARCH_MULTI_V4T || ARCH_MULTI_V5)
+	depends on !(ARCH_MOXART || ARCH_GEMINI || ARCH_SA1100)
+	depends on ATAGS
+	depends on CPU_LITTLE_ENDIAN
+	depends on MMU
+	select ARCH_NO_SG_CHAIN
+	select CPU_SA110
+	select FOOTBRIDGE
+	select NEED_MACH_MEMORY_H
+	help
+	  Support for systems based on the DC21285 companion chip
+	  ("FootBridge"), such as the Simtec CATS and the Rebel NetWinder.
 
-menu "Footbridge Implementations"
+if ARCH_FOOTBRIDGE
 
 config ARCH_CATS
 	bool "CATS"
+	depends on UNUSED_BOARD_FILES
 	select CLKEVT_I8253
 	select CLKSRC_I8253
-	select FOOTBRIDGE_HOST
 	select ISA
-	select ISA_DMA
 	select FORCE_PCI
 	help
 	  Say Y here if you intend to run this kernel on the CATS.
 
 	  Saying N will reduce the size of the Footbridge kernel.
 
-config ARCH_EBSA285_ADDIN
-	bool "EBSA285 (addin mode)"
-	select ARCH_EBSA285
-	select FOOTBRIDGE_ADDIN
-	help
-	  Say Y here if you intend to run this kernel on the EBSA285 card
-	  in addin mode.
-
-	  Saying N will reduce the size of the Footbridge kernel.
-
 config ARCH_EBSA285_HOST
 	bool "EBSA285 (host mode)"
 	select ARCH_EBSA285
-	select FOOTBRIDGE_HOST
 	select ISA
-	select ISA_DMA
 	select ARCH_MAY_HAVE_PC_FDC
 	select FORCE_PCI
 	help
@@ -44,9 +44,7 @@ config ARCH_NETWINDER
 	bool "NetWinder"
 	select CLKEVT_I8253
 	select CLKSRC_I8253
-	select FOOTBRIDGE_HOST
 	select ISA
-	select ISA_DMA
 	select FORCE_PCI
 	help
 	  Say Y here if you intend to run this kernel on the Rebel.COM
@@ -56,22 +54,12 @@ config ARCH_NETWINDER
 
 	  Saying N will reduce the size of the Footbridge kernel.
 
-endmenu
-
 # Footbridge support
 config FOOTBRIDGE
-	bool
-
-# Footbridge in host mode
-config FOOTBRIDGE_HOST
-	bool
+	def_bool y
 	select ARCH_MIGHT_HAVE_PC_SERIO
+	select ISA_DMA_API
 
-# Footbridge in addin mode
-config FOOTBRIDGE_ADDIN
-	bool
-
-# EBSA285 board in either host or addin mode
 config ARCH_EBSA285
 	bool
 
diff --git a/arch/arm/mach-footbridge/Makefile b/arch/arm/mach-footbridge/Makefile
index 6262993c0555..55d570739f19 100644
--- a/arch/arm/mach-footbridge/Makefile
+++ b/arch/arm/mach-footbridge/Makefile
@@ -5,11 +5,11 @@
 
 # Object file lists.
 
-obj-y			:= common.o dma.o isa-irq.o
+obj-y			:= common.o isa-irq.o isa.o isa-rtc.o dma-isa.o
 
 pci-y			+= dc21285.o
 pci-$(CONFIG_ARCH_CATS) += cats-pci.o
-pci-$(CONFIG_ARCH_EBSA285_HOST) += ebsa285-pci.o
+pci-$(CONFIG_ARCH_EBSA285) += ebsa285-pci.o
 pci-$(CONFIG_ARCH_NETWINDER) += netwinder-pci.o
 
 obj-$(CONFIG_ARCH_CATS) += cats-hw.o isa-timer.o
@@ -18,4 +18,3 @@ obj-$(CONFIG_ARCH_NETWINDER) += netwinder-hw.o isa-timer.o
 
 obj-$(CONFIG_PCI)	+=$(pci-y)
 
-obj-$(CONFIG_ISA)	+= isa.o isa-rtc.o
diff --git a/arch/arm/mach-footbridge/Makefile.boot b/arch/arm/mach-footbridge/Makefile.boot
deleted file mode 100644
index e4313e912cac..000000000000
--- a/arch/arm/mach-footbridge/Makefile.boot
+++ /dev/null
@@ -1,5 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0-only
-   zreladdr-y	+= 0x00008000
-params_phys-y	:= 0x00000100
-initrd_phys-y	:= 0x00800000
-
diff --git a/arch/arm/mach-footbridge/common.c b/arch/arm/mach-footbridge/common.c
index eee095f0e2f6..629e4676ed77 100644
--- a/arch/arm/mach-footbridge/common.c
+++ b/arch/arm/mach-footbridge/common.c
@@ -12,6 +12,7 @@
 #include <linux/init.h>
 #include <linux/io.h>
 #include <linux/spinlock.h>
+#include <linux/dma-direct.h>
 #include <video/vga.h>
 
 #include <asm/page.h>
@@ -27,6 +28,91 @@
 
 #include "common.h"
 
+#include <mach/hardware.h>
+#include <mach/irqs.h>
+#include <asm/hardware/dec21285.h>
+
+static int dc21285_get_irq(void)
+{
+	void __iomem *irqstatus = (void __iomem *)CSR_IRQ_STATUS;
+	u32 mask = readl(irqstatus);
+
+	if (mask & IRQ_MASK_SDRAMPARITY)
+		return IRQ_SDRAMPARITY;
+
+	if (mask & IRQ_MASK_UART_RX)
+		return IRQ_CONRX;
+
+	if (mask & IRQ_MASK_DMA1)
+		return IRQ_DMA1;
+
+	if (mask & IRQ_MASK_DMA2)
+		return IRQ_DMA2;
+
+	if (mask & IRQ_MASK_IN0)
+		return IRQ_IN0;
+
+	if (mask & IRQ_MASK_IN1)
+		return IRQ_IN1;
+
+	if (mask & IRQ_MASK_IN2)
+		return IRQ_IN2;
+
+	if (mask & IRQ_MASK_IN3)
+		return IRQ_IN3;
+
+	if (mask & IRQ_MASK_PCI)
+		return IRQ_PCI;
+
+	if (mask & IRQ_MASK_DOORBELLHOST)
+		return IRQ_DOORBELLHOST;
+
+	if (mask & IRQ_MASK_I2OINPOST)
+		return IRQ_I2OINPOST;
+
+	if (mask & IRQ_MASK_TIMER1)
+		return IRQ_TIMER1;
+
+	if (mask & IRQ_MASK_TIMER2)
+		return IRQ_TIMER2;
+
+	if (mask & IRQ_MASK_TIMER3)
+		return IRQ_TIMER3;
+
+	if (mask & IRQ_MASK_UART_TX)
+		return IRQ_CONTX;
+
+	if (mask & IRQ_MASK_PCI_ABORT)
+		return IRQ_PCI_ABORT;
+
+	if (mask & IRQ_MASK_PCI_SERR)
+		return IRQ_PCI_SERR;
+
+	if (mask & IRQ_MASK_DISCARD_TIMER)
+		return IRQ_DISCARD_TIMER;
+
+	if (mask & IRQ_MASK_PCI_DPERR)
+		return IRQ_PCI_DPERR;
+
+	if (mask & IRQ_MASK_PCI_PERR)
+		return IRQ_PCI_PERR;
+
+	return 0;
+}
+
+static void dc21285_handle_irq(struct pt_regs *regs)
+{
+	int irq;
+	do {
+		irq = dc21285_get_irq();
+		if (!irq)
+			break;
+
+		generic_handle_irq(irq);
+	} while (1);
+}
+
+
 unsigned int mem_fclk_21285 = 50000000;
 
 EXPORT_SYMBOL(mem_fclk_21285);
@@ -108,10 +194,9 @@ static void __init __fb_init_irq(void)
 
 void __init footbridge_init_irq(void)
 {
-	__fb_init_irq();
+	set_handle_irq(dc21285_handle_irq);
 
-	if (!footbridge_cfn_mode())
-		return;
+	__fb_init_irq();
 
 	if (machine_is_ebsa285())
 		/* The following is dependent on which slot
@@ -133,21 +218,13 @@ void __init footbridge_init_irq(void)
  * commented out since there is a "No Fix" problem with it.  Not mapping
  * it means that we have extra bullet protection on our feet.
  */
-static struct map_desc fb_common_io_desc[] __initdata = {
+static struct map_desc ebsa285_host_io_desc[] __initdata = {
 	{
 		.virtual	= ARMCSR_BASE,
 		.pfn		= __phys_to_pfn(DC21285_ARMCSR_BASE),
 		.length		= ARMCSR_SIZE,
 		.type		= MT_DEVICE,
-	}
-};
-
-/*
- * The mapping when the footbridge is in host mode.  We don't map any of
- * this when we are in add-in mode.
- */
-static struct map_desc ebsa285_host_io_desc[] __initdata = {
-#if defined(CONFIG_ARCH_FOOTBRIDGE) && defined(CONFIG_FOOTBRIDGE_HOST)
+	},
 	{
 		.virtual	= PCIMEM_BASE,
 		.pfn		= __phys_to_pfn(DC21285_PCI_MEM),
@@ -169,26 +246,12 @@ static struct map_desc ebsa285_host_io_desc[] __initdata = {
 		.length		= PCIIACK_SIZE,
 		.type		= MT_DEVICE,
 	},
-#endif
 };
 
 void __init footbridge_map_io(void)
 {
-	/*
-	 * Set up the common mapping first; we need this to
-	 * determine whether we're in host mode or not.
-	 */
-	iotable_init(fb_common_io_desc, ARRAY_SIZE(fb_common_io_desc));
-
-	/*
-	 * Now, work out what we've got to map in addition on this
-	 * platform.
-	 */
-	if (footbridge_cfn_mode()) {
-		iotable_init(ebsa285_host_io_desc, ARRAY_SIZE(ebsa285_host_io_desc));
-		pci_map_io_early(__phys_to_pfn(DC21285_PCI_IO));
-	}
-
+	iotable_init(ebsa285_host_io_desc, ARRAY_SIZE(ebsa285_host_io_desc));
+	pci_map_io_early(__phys_to_pfn(DC21285_PCI_IO));
 	vga_base = PCIMEM_BASE;
 }
 
@@ -218,47 +281,3 @@ void footbridge_restart(enum reboot_mode mode, const char *cmd)
 		*CSR_SA110_CNTL |= (1 << 13);
 	}
 }
-
-#ifdef CONFIG_FOOTBRIDGE_ADDIN
-
-static inline unsigned long fb_bus_sdram_offset(void)
-{
-	return *CSR_PCISDRAMBASE & 0xfffffff0;
-}
-
-/*
- * These two functions convert virtual addresses to PCI addresses and PCI
- * addresses to virtual addresses.  Note that it is only legal to use these
- * on memory obtained via get_zeroed_page or kmalloc.
- */
-unsigned long __virt_to_bus(unsigned long res)
-{
-	WARN_ON(res < PAGE_OFFSET || res >= (unsigned long)high_memory);
-
-	return res + (fb_bus_sdram_offset() - PAGE_OFFSET);
-}
-EXPORT_SYMBOL(__virt_to_bus);
-
-unsigned long __bus_to_virt(unsigned long res)
-{
-	res = res - (fb_bus_sdram_offset() - PAGE_OFFSET);
-
-	WARN_ON(res < PAGE_OFFSET || res >= (unsigned long)high_memory);
-
-	return res;
-}
-EXPORT_SYMBOL(__bus_to_virt);
-
-unsigned long __pfn_to_bus(unsigned long pfn)
-{
-	return __pfn_to_phys(pfn) + (fb_bus_sdram_offset() - PHYS_OFFSET);
-}
-EXPORT_SYMBOL(__pfn_to_bus);
-
-unsigned long __bus_to_pfn(unsigned long bus)
-{
-	return __phys_to_pfn(bus - (fb_bus_sdram_offset() - PHYS_OFFSET));
-}
-EXPORT_SYMBOL(__bus_to_pfn);
-
-#endif
diff --git a/arch/arm/mach-footbridge/dc21285.c b/arch/arm/mach-footbridge/dc21285.c
index f9713dc561cf..f8920d0010de 100644
--- a/arch/arm/mach-footbridge/dc21285.c
+++ b/arch/arm/mach-footbridge/dc21285.c
@@ -5,6 +5,7 @@
  *  Copyright (C) 1998-2001 Russell King
  *  Copyright (C) 1998-2000 Phil Blundell
  */
+#include <linux/dma-map-ops.h>
 #include <linux/kernel.h>
 #include <linux/pci.h>
 #include <linux/interrupt.h>
@@ -241,13 +242,26 @@ static irqreturn_t dc21285_parity_irq(int irq, void *dev_id)
 	return IRQ_HANDLED;
 }
 
+static int dc21285_pci_bus_notifier(struct notifier_block *nb,
+				    unsigned long action,
+				    void *data)
+{
+	if (action != BUS_NOTIFY_ADD_DEVICE)
+		return NOTIFY_DONE;
+
+	dma_direct_set_offset(data, PHYS_OFFSET, BUS_OFFSET, SZ_256M);
+
+	return NOTIFY_OK;
+}
+
+static struct notifier_block dc21285_pci_bus_nb = {
+	.notifier_call = dc21285_pci_bus_notifier,
+};
+
 int __init dc21285_setup(int nr, struct pci_sys_data *sys)
 {
 	struct resource *res;
 
-	if (nr || !footbridge_cfn_mode())
-		return 0;
-
 	res = kcalloc(2, sizeof(struct resource), GFP_KERNEL);
 	if (!res) {
 		printk("out of memory for root bus resources");
@@ -269,6 +283,8 @@ int __init dc21285_setup(int nr, struct pci_sys_data *sys)
 	pci_add_resource_offset(&sys->resources, &res[0], sys->mem_offset);
 	pci_add_resource_offset(&sys->resources, &res[1], sys->mem_offset);
 
+	bus_register_notifier(&pci_bus_type, &dc21285_pci_bus_nb);
+
 	return 1;
 }
 
@@ -278,7 +294,6 @@ int __init dc21285_setup(int nr, struct pci_sys_data *sys)
 void __init dc21285_preinit(void)
 {
 	unsigned int mem_size, mem_mask;
-	int cfn_mode;
 
 	pcibios_min_mem = 0x81000000;
 
@@ -298,21 +313,15 @@ void __init dc21285_preinit(void)
 	*CSR_CSRBASEOFFSET    = 0;
 	*CSR_PCIADDR_EXTN     = 0;
 
-	cfn_mode = __footbridge_cfn_mode();
-
 	printk(KERN_INFO "PCI: DC21285 footbridge, revision %02lX, in "
-		"%s mode\n", *CSR_CLASSREV & 0xff, cfn_mode ?
-		"central function" : "addin");
-
-	if (footbridge_cfn_mode()) {
-		/*
-		 * Clear any existing errors - we aren't
-		 * interested in historical data...
-		 */
-		*CSR_SA110_CNTL	= (*CSR_SA110_CNTL & 0xffffde07) |
-				  SA110_CNTL_RXSERR;
-		*CSR_PCICMD = (*CSR_PCICMD & 0xffff) | PCICMD_ERROR_BITS;
-	}
+		"central function mode\n", *CSR_CLASSREV & 0xff);
+
+	/*
+	 * Clear any existing errors - we aren't
+	 * interested in historical data...
+	 */
+	*CSR_SA110_CNTL	= (*CSR_SA110_CNTL & 0xffffde07) | SA110_CNTL_RXSERR;
+	*CSR_PCICMD = (*CSR_PCICMD & 0xffff) | PCICMD_ERROR_BITS;
 
 	timer_setup(&serr_timer, dc21285_enable_error, 0);
 	timer_setup(&perr_timer, dc21285_enable_error, 0);
@@ -331,29 +340,18 @@ void __init dc21285_preinit(void)
 	dc21285_request_irq(IRQ_PCI_DPERR, dc21285_dparity_irq, 0,
 			    "PCI data parity", NULL);
 
-	if (cfn_mode) {
-		/*
-		 * Map our SDRAM at a known address in PCI space, just in case
-		 * the firmware had other ideas.  Using a nonzero base is
-		 * necessary, since some VGA cards forcefully use PCI addresses
-		 * in the range 0x000a0000 to 0x000c0000. (eg, S3 cards).
-		 */
-		*CSR_PCICSRBASE       = 0xf4000000;
-		*CSR_PCICSRIOBASE     = 0;
-		*CSR_PCISDRAMBASE     = __virt_to_bus(PAGE_OFFSET);
-		*CSR_PCIROMBASE       = 0;
-		*CSR_PCICMD = PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER |
-			      PCI_COMMAND_INVALIDATE | PCICMD_ERROR_BITS;
-	} else if (footbridge_cfn_mode() != 0) {
-		/*
-		 * If we are not compiled to accept "add-in" mode, then
-		 * we are using a constant virt_to_bus translation which
-		 * can not hope to cater for the way the host BIOS  has
-		 * set up the machine.
-		 */
-		panic("PCI: this kernel is compiled for central "
-			"function mode only");
-	}
+	/*
+	 * Map our SDRAM at a known address in PCI space, just in case
+	 * the firmware had other ideas.  Using a nonzero base is
+	 * necessary, since some VGA cards forcefully use PCI addresses
+	 * in the range 0x000a0000 to 0x000c0000. (eg, S3 cards).
+	 */
+	*CSR_PCICSRBASE       = 0xf4000000;
+	*CSR_PCICSRIOBASE     = 0;
+	*CSR_PCISDRAMBASE     = BUS_OFFSET;
+	*CSR_PCIROMBASE       = 0;
+	*CSR_PCICMD = PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER |
+		      PCI_COMMAND_INVALIDATE | PCICMD_ERROR_BITS;
 }
 
 void __init dc21285_postinit(void)
diff --git a/arch/arm/kernel/dma-isa.c b/arch/arm/mach-footbridge/dma-isa.c
index 2d90ecce5a11..937f5376d5e7 100644
--- a/arch/arm/kernel/dma-isa.c
+++ b/arch/arm/mach-footbridge/dma-isa.c
@@ -1,7 +1,5 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- *  linux/arch/arm/kernel/dma-isa.c
- *
  *  Copyright (C) 1999-2000 Russell King
  *
  *  ISA DMA primitives
@@ -13,6 +11,7 @@
  *   arch/arm/kernel/dma-ebsa285.c
  *   Copyright (C) 1998 Phil Blundell
  */
+#include <linux/dma-map-ops.h>
 #include <linux/ioport.h>
 #include <linux/init.h>
 #include <linux/dma-mapping.h>
@@ -20,6 +19,7 @@
 
 #include <asm/dma.h>
 #include <asm/mach/dma.h>
+#include <asm/hardware/dec21285.h>
 
 #define ISA_DMA_MASK		0
 #define ISA_DMA_MODE		1
@@ -157,7 +157,7 @@ static dma_t isa_dma[8];
 /*
  * ISA DMA always starts at channel 0
  */
-void __init isa_init_dma(void)
+static int __init isa_dma_init(void)
 {
 	/*
 	 * Try to autodetect presence of an ISA DMA controller.
@@ -222,4 +222,9 @@ void __init isa_init_dma(void)
 
 		request_dma(DMA_ISA_CASCADE, "cascade");
 	}
+
+	dma_direct_set_offset(&isa_dma_dev, PHYS_OFFSET, BUS_OFFSET, SZ_256M);
+
+	return 0;
 }
+core_initcall(isa_dma_init);
diff --git a/arch/arm/mach-footbridge/dma.c b/arch/arm/mach-footbridge/dma.c
deleted file mode 100644
index 86618074a7a5..000000000000
--- a/arch/arm/mach-footbridge/dma.c
+++ /dev/null
@@ -1,58 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- *  linux/arch/arm/kernel/dma-ebsa285.c
- *
- *  Copyright (C) 1998 Phil Blundell
- *
- * DMA functions specific to EBSA-285/CATS architectures
- *
- *  Changelog:
- *   09-Nov-1998 RMK	Split out ISA DMA functions to dma-isa.c
- *   17-Mar-1999 RMK	Allow any EBSA285-like architecture to have
- *			ISA DMA controllers.
- */
-#include <linux/init.h>
-#include <linux/io.h>
-#include <linux/spinlock.h>
-#include <linux/scatterlist.h>
-
-#include <asm/dma.h>
-
-#include <asm/mach/dma.h>
-#include <asm/hardware/dec21285.h>
-
-#if 0
-static int fb_dma_request(unsigned int chan, dma_t *dma)
-{
-	return -EINVAL;
-}
-
-static void fb_dma_enable(unsigned int chan, dma_t *dma)
-{
-}
-
-static void fb_dma_disable(unsigned int chan, dma_t *dma)
-{
-}
-
-static struct dma_ops fb_dma_ops = {
-	.type		= "fb",
-	.request	= fb_dma_request,
-	.enable		= fb_dma_enable,
-	.disable	= fb_dma_disable,
-};
-#endif
-
-static int __init fb_dma_init(void)
-{
-#if 0
-	dma[_DC21285_DMA(0)].d_ops = &fb_dma_ops;
-	dma[_DC21285_DMA(1)].d_ops = &fb_dma_ops;
-#endif
-#ifdef CONFIG_ISA_DMA
-	if (footbridge_cfn_mode())
-		isa_init_dma();
-#endif
-	return 0;
-}
-core_initcall(fb_dma_init);
diff --git a/arch/arm/mach-footbridge/include/mach/entry-macro.S b/arch/arm/mach-footbridge/include/mach/entry-macro.S
deleted file mode 100644
index dabbd5c54a78..000000000000
--- a/arch/arm/mach-footbridge/include/mach/entry-macro.S
+++ /dev/null
@@ -1,107 +0,0 @@
-/*
- * arch/arm/mach-footbridge/include/mach/entry-macro.S
- *
- * Low-level IRQ helper macros for footbridge-based platforms
- *
- * This file is licensed under  the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-#include <mach/hardware.h>
-#include <mach/irqs.h>
-#include <asm/hardware/dec21285.h>
-
-		.equ	dc21285_high, ARMCSR_BASE & 0xff000000
-		.equ	dc21285_low, ARMCSR_BASE & 0x00ffffff
-
-		.macro  get_irqnr_preamble, base, tmp
-		mov	\base, #dc21285_high
-		.if	dc21285_low
-		orr	\base, \base, #dc21285_low
-		.endif
-		.endm
-
-		.macro	get_irqnr_and_base, irqnr, irqstat, base, tmp
-		ldr	\irqstat, [\base, #0x180]	@ get interrupts
-
-		mov	\irqnr, #IRQ_SDRAMPARITY
-		tst	\irqstat, #IRQ_MASK_SDRAMPARITY
-		bne	1001f
-
-		tst	\irqstat, #IRQ_MASK_UART_RX
-		movne	\irqnr, #IRQ_CONRX
-		bne	1001f
-
-		tst	\irqstat, #IRQ_MASK_DMA1
-		movne	\irqnr, #IRQ_DMA1
-		bne	1001f
-
-		tst	\irqstat, #IRQ_MASK_DMA2
-		movne	\irqnr, #IRQ_DMA2
-		bne	1001f
-
-		tst	\irqstat, #IRQ_MASK_IN0
-		movne	\irqnr, #IRQ_IN0
-		bne	1001f
-
-		tst	\irqstat, #IRQ_MASK_IN1
-		movne	\irqnr, #IRQ_IN1
-		bne	1001f
-
-		tst	\irqstat, #IRQ_MASK_IN2
-		movne	\irqnr, #IRQ_IN2
-		bne	1001f
-
-		tst	\irqstat, #IRQ_MASK_IN3
-		movne	\irqnr, #IRQ_IN3
-		bne	1001f
-
-		tst	\irqstat, #IRQ_MASK_PCI
-		movne	\irqnr, #IRQ_PCI
-		bne	1001f
-
-		tst	\irqstat, #IRQ_MASK_DOORBELLHOST
-		movne	\irqnr, #IRQ_DOORBELLHOST
-		bne     1001f
-
-		tst	\irqstat, #IRQ_MASK_I2OINPOST
-		movne	\irqnr, #IRQ_I2OINPOST
-		bne	1001f
-
-		tst	\irqstat, #IRQ_MASK_TIMER1
-		movne	\irqnr, #IRQ_TIMER1
-		bne	1001f
-
-		tst	\irqstat, #IRQ_MASK_TIMER2
-		movne	\irqnr, #IRQ_TIMER2
-		bne	1001f
-
-		tst	\irqstat, #IRQ_MASK_TIMER3
-		movne	\irqnr, #IRQ_TIMER3
-		bne	1001f
-
-		tst	\irqstat, #IRQ_MASK_UART_TX
-		movne	\irqnr, #IRQ_CONTX
-		bne	1001f
-
-		tst	\irqstat, #IRQ_MASK_PCI_ABORT
-		movne	\irqnr, #IRQ_PCI_ABORT
-		bne	1001f
-
-		tst	\irqstat, #IRQ_MASK_PCI_SERR
-		movne	\irqnr, #IRQ_PCI_SERR
-		bne	1001f
-
-		tst	\irqstat, #IRQ_MASK_DISCARD_TIMER
-		movne	\irqnr, #IRQ_DISCARD_TIMER
-		bne	1001f
-
-		tst	\irqstat, #IRQ_MASK_PCI_DPERR
-		movne	\irqnr, #IRQ_PCI_DPERR
-		bne	1001f
-
-		tst	\irqstat, #IRQ_MASK_PCI_PERR
-		movne	\irqnr, #IRQ_PCI_PERR
-1001:
-		.endm
-
diff --git a/arch/arm/mach-footbridge/include/mach/hardware.h b/arch/arm/mach-footbridge/include/mach/hardware.h
index ecaf6e7388d9..985ad3a95671 100644
--- a/arch/arm/mach-footbridge/include/mach/hardware.h
+++ b/arch/arm/mach-footbridge/include/mach/hardware.h
@@ -21,32 +21,26 @@
  * 0xf0000000	0x80000000	16MB	ISA memory
  */
 
-#ifdef CONFIG_MMU
-#define MMU_IO(a, b)	(a)
-#else
-#define MMU_IO(a, b)	(b)
-#endif
-
 #define XBUS_SIZE		0x00100000
-#define XBUS_BASE		MMU_IO(0xff800000, 0x40000000)
+#define XBUS_BASE		0xff800000
 
 #define ARMCSR_SIZE		0x00100000
-#define ARMCSR_BASE		MMU_IO(0xfe000000, 0x42000000)
+#define ARMCSR_BASE		0xfe000000
 
 #define WFLUSH_SIZE		0x00100000
-#define WFLUSH_BASE		MMU_IO(0xfd000000, 0x78000000)
+#define WFLUSH_BASE		0xfd000000
 
 #define PCIIACK_SIZE		0x00100000
-#define PCIIACK_BASE		MMU_IO(0xfc000000, 0x79000000)
+#define PCIIACK_BASE		0xfc000000
 
 #define PCICFG1_SIZE		0x01000000
-#define PCICFG1_BASE		MMU_IO(0xfb000000, 0x7a000000)
+#define PCICFG1_BASE		0xfb000000
 
 #define PCICFG0_SIZE		0x01000000
-#define PCICFG0_BASE		MMU_IO(0xfa000000, 0x7b000000)
+#define PCICFG0_BASE		0xfa000000
 
 #define PCIMEM_SIZE		0x01000000
-#define PCIMEM_BASE		MMU_IO(0xf0000000, 0x80000000)
+#define PCIMEM_BASE		0xf0000000
 
 #define XBUS_CS2		0x40012000
 
diff --git a/arch/arm/mach-footbridge/include/mach/io.h b/arch/arm/mach-footbridge/include/mach/io.h
deleted file mode 100644
index 4e18b921373f..000000000000
--- a/arch/arm/mach-footbridge/include/mach/io.h
+++ /dev/null
@@ -1,20 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-only */
-/*
- *  arch/arm/mach-footbridge/include/mach/io.h
- *
- *  Copyright (C) 1997-1999 Russell King
- *
- *  Modifications:
- *   06-12-1997	RMK	Created.
- *   07-04-1999	RMK	Major cleanup
- */
-#ifndef __ASM_ARM_ARCH_IO_H
-#define __ASM_ARM_ARCH_IO_H
-
-/*
- * Translation of various i/o addresses to host addresses for !CONFIG_MMU
- */
-#define PCIO_BASE       0x7c000000
-#define __io(a)			((void __iomem *)(PCIO_BASE + (a)))
-
-#endif
diff --git a/arch/arm/mach-footbridge/include/mach/isa-dma.h b/arch/arm/mach-footbridge/include/mach/isa-dma.h
index 8a1b991076e1..b10731a1f66a 100644
--- a/arch/arm/mach-footbridge/include/mach/isa-dma.h
+++ b/arch/arm/mach-footbridge/include/mach/isa-dma.h
@@ -10,17 +10,9 @@
 #ifndef __ASM_ARCH_DMA_H
 #define __ASM_ARCH_DMA_H
 
-/*
- * The 21285 has two internal DMA channels; we call these 8 and 9.
- * On CATS hardware we have an additional eight ISA dma channels
- * numbered 0..7.
- */
-#define _ISA_DMA(x)		(0+(x))
-#define _DC21285_DMA(x)		(8+(x))
-
-#define MAX_DMA_CHANNELS	10
+#define MAX_DMA_CHANNELS	8
 
-#define DMA_FLOPPY		_ISA_DMA(2)
-#define DMA_ISA_CASCADE		_ISA_DMA(4)
+#define DMA_FLOPPY		(2)
+#define DMA_ISA_CASCADE		(4)
 
 #endif /* _ASM_ARCH_DMA_H */
diff --git a/arch/arm/mach-footbridge/include/mach/memory.h b/arch/arm/mach-footbridge/include/mach/memory.h
index 46fd4a8872b9..9516877667d7 100644
--- a/arch/arm/mach-footbridge/include/mach/memory.h
+++ b/arch/arm/mach-footbridge/include/mach/memory.h
@@ -16,41 +16,6 @@
 #ifndef __ASM_ARCH_MEMORY_H
 #define __ASM_ARCH_MEMORY_H
 
-
-#if defined(CONFIG_FOOTBRIDGE_ADDIN)
-/*
- * If we may be using add-in footbridge mode, then we must
- * use the out-of-line translation that makes use of the
- * PCI BAR
- */
-#ifndef __ASSEMBLY__
-extern unsigned long __virt_to_bus(unsigned long);
-extern unsigned long __bus_to_virt(unsigned long);
-extern unsigned long __pfn_to_bus(unsigned long);
-extern unsigned long __bus_to_pfn(unsigned long);
-#endif
-#define __virt_to_bus	__virt_to_bus
-#define __bus_to_virt	__bus_to_virt
-
-#elif defined(CONFIG_FOOTBRIDGE_HOST)
-
-/*
- * The footbridge is programmed to expose the system RAM at 0xe0000000.
- * The requirement is that the RAM isn't placed at bus address 0, which
- * would clash with VGA cards.
- */
-#define BUS_OFFSET		0xe0000000
-#define __virt_to_bus(x)	((x) + (BUS_OFFSET - PAGE_OFFSET))
-#define __bus_to_virt(x)	((x) - (BUS_OFFSET - PAGE_OFFSET))
-#define __pfn_to_bus(x)		(__pfn_to_phys(x) + (BUS_OFFSET - PHYS_OFFSET))
-#define __bus_to_pfn(x)		__phys_to_pfn((x) - (BUS_OFFSET - PHYS_OFFSET))
-
-#else
-
-#error "Undefined footbridge mode"
-
-#endif
-
 /*
  * Cache flushing area.
  */
diff --git a/arch/arm/mach-footbridge/isa.c b/arch/arm/mach-footbridge/isa.c
index ec5af521cf95..84caccddce44 100644
--- a/arch/arm/mach-footbridge/isa.c
+++ b/arch/arm/mach-footbridge/isa.c
@@ -79,16 +79,12 @@ static int __init footbridge_isa_init(void)
 {
 	int err = 0;
 
-	if (!footbridge_cfn_mode())
-		return 0;
-
 	/* Personal server doesn't have RTC */
-	if (!machine_is_personal_server()) {
-		isa_rtc_init();
-		err = platform_device_register(&rtc_device);
-		if (err)
-			printk(KERN_ERR "Unable to register RTC device: %d\n", err);
-	}
+	isa_rtc_init();
+	err = platform_device_register(&rtc_device);
+	if (err)
+		printk(KERN_ERR "Unable to register RTC device: %d\n", err);
+
 	err = platform_device_register(&serial_device);
 	if (err)
 		printk(KERN_ERR "Unable to register serial device: %d\n", err);
diff --git a/arch/arm/mach-gemini/Kconfig b/arch/arm/mach-gemini/Kconfig
index 969674ea5f17..f436a2009eca 100644
--- a/arch/arm/mach-gemini/Kconfig
+++ b/arch/arm/mach-gemini/Kconfig
@@ -2,6 +2,7 @@
 menuconfig ARCH_GEMINI
 	bool "Cortina Systems Gemini"
 	depends on ARCH_MULTI_V4
+	depends on CPU_LITTLE_ENDIAN
 	select ARCH_HAS_RESET_CONTROLLER
 	select ARM_AMBA
 	select ARM_APPENDED_DTB # Old Redboot bootloaders deployed
diff --git a/arch/arm/mach-highbank/Kconfig b/arch/arm/mach-highbank/Kconfig
index 9de38ce8124f..c2d6ef6b3927 100644
--- a/arch/arm/mach-highbank/Kconfig
+++ b/arch/arm/mach-highbank/Kconfig
@@ -2,7 +2,6 @@
 config ARCH_HIGHBANK
 	bool "Calxeda ECX-1000/2000 (Highbank/Midway)"
 	depends on ARCH_MULTI_V7
-	select ARCH_SUPPORTS_BIG_ENDIAN
 	select ARM_AMBA
 	select ARM_ERRATA_764369 if SMP
 	select ARM_ERRATA_775420
diff --git a/arch/arm/mach-highbank/highbank.c b/arch/arm/mach-highbank/highbank.c
index db607955a7e4..5d4f977ac7d2 100644
--- a/arch/arm/mach-highbank/highbank.c
+++ b/arch/arm/mach-highbank/highbank.c
@@ -98,7 +98,7 @@ static int highbank_platform_notifier(struct notifier_block *nb,
 	if (of_property_read_bool(dev->of_node, "dma-coherent")) {
 		val = readl(sregs_base + reg);
 		writel(val | 0xff01, sregs_base + reg);
-		set_dma_ops(dev, &arm_coherent_dma_ops);
+		dev->dma_coherent = true;
 	}
 
 	return NOTIFY_OK;
diff --git a/arch/arm/mach-hisi/Kconfig b/arch/arm/mach-hisi/Kconfig
index 2e980f834a6a..7b3440687176 100644
--- a/arch/arm/mach-hisi/Kconfig
+++ b/arch/arm/mach-hisi/Kconfig
@@ -1,7 +1,7 @@
 # SPDX-License-Identifier: GPL-2.0-only
 config ARCH_HISI
 	bool "Hisilicon SoC Support"
-	depends on ARCH_MULTI_V7 || ARCH_MULTI_V5
+	depends on ARCH_MULTI_V7 || (ARCH_MULTI_V5 && CPU_LITTLE_ENDIAN)
 	select ARM_AMBA
 	select ARM_GIC if ARCH_MULTI_V7
 	select ARM_TIMER_SP804
@@ -40,7 +40,7 @@ config ARCH_HIP04
 	select HAVE_ARM_ARCH_TIMER
 	select MCPM if SMP
 	select MCPM_QUAD_CLUSTER if SMP
-	select GENERIC_IRQ_EFFECTIVE_AFF_MASK
+	select GENERIC_IRQ_EFFECTIVE_AFF_MASK if SMP
 	help
 	  Support for Hisilicon HiP04 SoC family
 
diff --git a/arch/arm/mach-hisi/platsmp.c b/arch/arm/mach-hisi/platsmp.c
index a56cc64deeb8..9ce93e0b6cdc 100644
--- a/arch/arm/mach-hisi/platsmp.c
+++ b/arch/arm/mach-hisi/platsmp.c
@@ -67,14 +67,17 @@ static void __init hi3xxx_smp_prepare_cpus(unsigned int max_cpus)
 		}
 		ctrl_base = of_iomap(np, 0);
 		if (!ctrl_base) {
+			of_node_put(np);
 			pr_err("failed to map address\n");
 			return;
 		}
 		if (of_property_read_u32(np, "smp-offset", &offset) < 0) {
+			of_node_put(np);
 			pr_err("failed to find smp-offset property\n");
 			return;
 		}
 		ctrl_base += offset;
+		of_node_put(np);
 	}
 }
 
@@ -160,6 +163,7 @@ static int hip01_boot_secondary(unsigned int cpu, struct task_struct *idle)
 	if (WARN_ON(!node))
 		return -1;
 	ctrl_base = of_iomap(node, 0);
+	of_node_put(node);
 
 	/* set the secondary core boot from DDR */
 	remap_reg_value = readl_relaxed(ctrl_base + REG_SC_CTRL);
diff --git a/arch/arm/mach-hpe/Kconfig b/arch/arm/mach-hpe/Kconfig
new file mode 100644
index 000000000000..3372bbf38d38
--- /dev/null
+++ b/arch/arm/mach-hpe/Kconfig
@@ -0,0 +1,23 @@
+menuconfig ARCH_HPE
+	bool "HPE SoC support"
+	depends on ARCH_MULTI_V7
+	help
+	  This enables support for HPE ARM based BMC chips.
+if ARCH_HPE
+
+config ARCH_HPE_GXP
+	bool "HPE GXP SoC"
+	depends on ARCH_MULTI_V7
+	select ARM_VIC
+	select GENERIC_IRQ_CHIP
+	select CLKSRC_MMIO
+	help
+	  HPE GXP is the name of the HPE Soc. This SoC is used to implement many
+	  BMC features at HPE. It supports ARMv7 architecture based on the Cortex
+	  A9 core. It is capable of using an AXI bus to which a memory controller
+	  is attached. It has multiple SPI interfaces to connect boot flash and
+	  BIOS flash. It uses a 10/100/1000 MAC for network connectivity. It
+	  has multiple i2c engines to drive connectivity with a host
+	  infrastructure.
+
+endif
diff --git a/arch/arm/mach-hpe/Makefile b/arch/arm/mach-hpe/Makefile
new file mode 100644
index 000000000000..8b0a91234df4
--- /dev/null
+++ b/arch/arm/mach-hpe/Makefile
@@ -0,0 +1 @@
+obj-$(CONFIG_ARCH_HPE_GXP) += gxp.o
diff --git a/arch/arm/mach-hpe/gxp.c b/arch/arm/mach-hpe/gxp.c
new file mode 100644
index 000000000000..ef3341373006
--- /dev/null
+++ b/arch/arm/mach-hpe/gxp.c
@@ -0,0 +1,16 @@
+// SPDX-License-Identifier: GPL-2.0
+/* Copyright (C) 2022 Hewlett-Packard Enterprise Development Company, L.P. */
+
+#include <linux/of_platform.h>
+#include <asm/mach/arch.h>
+
+static const char * const gxp_board_dt_compat[] = {
+	"hpe,gxp",
+	NULL,
+};
+
+DT_MACHINE_START(GXP_DT, "HPE GXP")
+	.dt_compat	= gxp_board_dt_compat,
+	.l2c_aux_val = 0,
+	.l2c_aux_mask = ~0,
+MACHINE_END
diff --git a/arch/arm/mach-imx/Kconfig b/arch/arm/mach-imx/Kconfig
index b407b024dde3..ab767f059929 100644
--- a/arch/arm/mach-imx/Kconfig
+++ b/arch/arm/mach-imx/Kconfig
@@ -1,8 +1,8 @@
 # SPDX-License-Identifier: GPL-2.0-only
 menuconfig ARCH_MXC
 	bool "Freescale i.MX family"
-	depends on ARCH_MULTI_V4_V5 || ARCH_MULTI_V6_V7 || ARM_SINGLE_ARMV7M
-	select ARCH_SUPPORTS_BIG_ENDIAN
+	depends on ((ARCH_MULTI_V4T || ARCH_MULTI_V5) && CPU_LITTLE_ENDIAN) || \
+		ARCH_MULTI_V6_V7 || ARM_SINGLE_ARMV7M
 	select CLKSRC_IMX_GPT
 	select GENERIC_IRQ_CHIP
 	select GPIOLIB
@@ -21,18 +21,6 @@ config MXC_TZIC
 config MXC_AVIC
 	bool
 
-config MXC_DEBUG_BOARD
-	bool "Enable MXC debug board(for 3-stack)"
-	depends on MACH_MX27_3DS || MACH_MX31_3DS || MACH_MX35_3DS
-	help
-	  The debug board is an integral part of the MXC 3-stack(PDK)
-	  platforms, it can be attached or removed from the peripheral
-	  board. On debug board, several debug devices(ethernet, UART,
-	  buttons, LEDs and JTAG) are implemented. Between the MCU and
-	  these devices, a CPLD is added as a bridge which performs
-	  data/address de-multiplexing and decode, signal level shift,
-	  interrupt control and various board functions.
-
 config HAVE_IMX_ANATOP
 	bool
 
@@ -108,7 +96,7 @@ config SOC_IMX5
 	select HAVE_IMX_SRC
 	select MXC_TZIC
 
-config	SOC_IMX50
+config SOC_IMX50
 	bool "i.MX50 support"
 	select PINCTRL_IMX50
 	select SOC_IMX5
@@ -123,7 +111,7 @@ config SOC_IMX51
 	help
 	  This enables support for Freescale i.MX51 processor
 
-config	SOC_IMX53
+config SOC_IMX53
 	bool "i.MX53 support"
 	select PINCTRL_IMX53
 	select SOC_IMX5
@@ -228,7 +216,7 @@ config SOC_IMX7D
 	select SOC_IMX7D_CM4 if ARM_SINGLE_ARMV7M
 	select ARM_ERRATA_814220 if ARCH_MULTI_V7
 	help
-		This enables support for Freescale i.MX7 Dual processor.
+	  This enables support for Freescale i.MX7 Dual processor.
 
 config SOC_IMX7ULP
 	bool "i.MX7ULP support"
@@ -239,6 +227,13 @@ config SOC_IMX7ULP
 	help
 	  This enables support for Freescale i.MX7 Ultra Low Power processor.
 
+config SOC_IMXRT
+	bool "i.MXRT support"
+	depends on ARM_SINGLE_ARMV7M
+	select ARMV7M_SYSTICK if ARM_SINGLE_ARMV7M
+	help
+	  This enables support for Freescale i.MXRT Crossover processor.
+
 config SOC_VF610
 	bool "Vybrid Family VF610 support"
 	select ARM_GIC if ARCH_MULTI_V7
diff --git a/arch/arm/mach-imx/Makefile b/arch/arm/mach-imx/Makefile
index d1506ef7a537..6fb3965b9ae6 100644
--- a/arch/arm/mach-imx/Makefile
+++ b/arch/arm/mach-imx/Makefile
@@ -14,8 +14,6 @@ obj-$(CONFIG_SOC_IMX5) += cpu-imx5.o $(imx5-pm-y)
 obj-$(CONFIG_MXC_TZIC) += tzic.o
 obj-$(CONFIG_MXC_AVIC) += avic.o
 
-obj-$(CONFIG_MXC_DEBUG_BOARD) += 3ds_debugboard.o
-
 ifeq ($(CONFIG_CPU_IDLE),y)
 obj-$(CONFIG_SOC_IMX5) += cpuidle-imx5.o
 obj-$(CONFIG_SOC_IMX6Q) += cpuidle-imx6q.o
@@ -65,6 +63,8 @@ obj-$(CONFIG_SOC_IMX50) += mach-imx50.o
 obj-$(CONFIG_SOC_IMX51) += mach-imx51.o
 obj-$(CONFIG_SOC_IMX53) += mach-imx53.o
 
+obj-$(CONFIG_SOC_IMXRT) += mach-imxrt.o
+
 obj-$(CONFIG_SOC_VF610) += mach-vf610.o
 
 obj-$(CONFIG_SOC_LS1021A) += mach-ls1021a.o
diff --git a/arch/arm/mach-imx/cpu-imx25.c b/arch/arm/mach-imx/cpu-imx25.c
index b2e1963f473d..3e63445cde06 100644
--- a/arch/arm/mach-imx/cpu-imx25.c
+++ b/arch/arm/mach-imx/cpu-imx25.c
@@ -32,6 +32,8 @@ static int mx25_read_cpu_rev(void)
 		return IMX_CHIP_REVISION_1_0;
 	case 0x01:
 		return IMX_CHIP_REVISION_1_1;
+	case 0x02:
+		return IMX_CHIP_REVISION_1_2;
 	default:
 		return IMX_CHIP_REVISION_UNKNOWN;
 	}
diff --git a/arch/arm/mach-imx/cpuidle-imx6q.c b/arch/arm/mach-imx/cpuidle-imx6q.c
index 094337dc1bc7..d086cbae09c3 100644
--- a/arch/arm/mach-imx/cpuidle-imx6q.c
+++ b/arch/arm/mach-imx/cpuidle-imx6q.c
@@ -3,6 +3,7 @@
  * Copyright (C) 2012 Freescale Semiconductor, Inc.
  */
 
+#include <linux/context_tracking.h>
 #include <linux/cpuidle.h>
 #include <linux/module.h>
 #include <asm/cpuidle.h>
@@ -24,9 +25,9 @@ static int imx6q_enter_wait(struct cpuidle_device *dev,
 		imx6_set_lpm(WAIT_UNCLOCKED);
 	raw_spin_unlock(&cpuidle_lock);
 
-	rcu_idle_enter();
+	ct_idle_enter();
 	cpu_do_idle();
-	rcu_idle_exit();
+	ct_idle_exit();
 
 	raw_spin_lock(&cpuidle_lock);
 	if (num_idle_cpus-- == num_online_cpus())
diff --git a/arch/arm/mach-imx/mach-imxrt.c b/arch/arm/mach-imx/mach-imxrt.c
new file mode 100644
index 000000000000..2063a3059c84
--- /dev/null
+++ b/arch/arm/mach-imx/mach-imxrt.c
@@ -0,0 +1,19 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2019
+ * Author(s): Giulio Benetti <giulio.benetti@benettiengineering.com>
+ */
+
+#include <linux/kernel.h>
+#include <asm/mach/arch.h>
+#include <asm/v7m.h>
+
+static const char *const imxrt_compat[] __initconst = {
+	"fsl,imxrt1050",
+	NULL
+};
+
+DT_MACHINE_START(IMXRTDT, "IMXRT (Device Tree Support)")
+	.dt_compat = imxrt_compat,
+	.restart = armv7m_restart,
+MACHINE_END
diff --git a/arch/arm/mach-integrator/Kconfig b/arch/arm/mach-integrator/Kconfig
deleted file mode 100644
index 63a0ca82659a..000000000000
--- a/arch/arm/mach-integrator/Kconfig
+++ /dev/null
@@ -1,160 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0-only
-menuconfig ARCH_INTEGRATOR
-	bool "ARM Ltd. Integrator family"
-	depends on ARCH_MULTI_V4T || ARCH_MULTI_V5 || ARCH_MULTI_V6
-	select ARM_AMBA
-	select CMA
-	select DMA_CMA
-	select HAVE_TCM
-	select CLK_ICST
-	select MFD_SYSCON
-	select PLAT_VERSATILE
-	select POWER_RESET
-	select POWER_RESET_VERSATILE
-	select POWER_SUPPLY
-	select SOC_INTEGRATOR_CM
-	select VERSATILE_FPGA_IRQ
-	help
-	  Support for ARM's Integrator platform.
-
-if ARCH_INTEGRATOR
-
-config ARCH_INTEGRATOR_AP
-	bool "Support Integrator/AP and Integrator/PP2 platforms"
-	select INTEGRATOR_AP_TIMER
-	select SERIAL_AMBA_PL010 if TTY
-	select SERIAL_AMBA_PL010_CONSOLE if TTY
-	select SOC_BUS
-	help
-	  Include support for the ARM(R) Integrator/AP and
-	  Integrator/PP2 platforms.
-
-config INTEGRATOR_IMPD1
-	bool "Include support for Integrator/IM-PD1"
-	depends on ARCH_INTEGRATOR_AP
-	select ARM_VIC
-	select GPIO_PL061
-	select GPIOLIB
-	select REGULATOR
-	select REGULATOR_FIXED_VOLTAGE
-	help
-	  The IM-PD1 is an add-on logic module for the Integrator which
-	  allows ARM(R) Ltd PrimeCells to be developed and evaluated.
-	  The IM-PD1 can be found on the Integrator/PP2 platform.
-
-config INTEGRATOR_CM7TDMI
-	bool "Integrator/CM7TDMI core module"
-	depends on ARCH_INTEGRATOR_AP
-	depends on ARCH_MULTI_V4 && !MMU
-	select CPU_ARM7TDMI
-
-config INTEGRATOR_CM720T
-	bool "Integrator/CM720T core module"
-	depends on ARCH_INTEGRATOR_AP
-	depends on ARCH_MULTI_V4T
-	select CPU_ARM720T
-
-config INTEGRATOR_CM740T
-	bool "Integrator/CM740T core module"
-	depends on ARCH_INTEGRATOR_AP
-	depends on ARCH_MULTI_V4T && !MMU
-	select CPU_ARM740T
-
-config INTEGRATOR_CM920T
-	bool "Integrator/CM920T core module"
-	depends on ARCH_INTEGRATOR_AP
-	depends on ARCH_MULTI_V4T
-	select CPU_ARM920T
-
-config INTEGRATOR_CM922T_XA10
-	bool "Integrator/CM922T-XA10 core module"
-	depends on ARCH_MULTI_V4T
-	depends on ARCH_INTEGRATOR_AP
-	select CPU_ARM922T
-
-config INTEGRATOR_CM926EJS
-	bool "Integrator/CM926EJ-S core module"
-	depends on ARCH_INTEGRATOR_AP
-	depends on ARCH_MULTI_V5
-	select CPU_ARM926T
-
-config INTEGRATOR_CM940T
-	bool "Integrator/CM940T core module"
-	depends on ARCH_INTEGRATOR_AP
-	depends on ARCH_MULTI_V4T && !MMU
-	select CPU_ARM940T
-
-config INTEGRATOR_CM946ES
-	bool "Integrator/CM946E-S core module"
-	depends on ARCH_INTEGRATOR_AP
-	depends on ARCH_MULTI_V5 && !MMU
-	select CPU_ARM946E
-
-config INTEGRATOR_CM966ES
-	bool "Integrator/CM966E-S core module"
-	depends on ARCH_INTEGRATOR_AP
-	depends on BROKEN # no kernel support
-
-config INTEGRATOR_CM10200E_REV0
-	bool "Integrator/CM10200E rev.0 core module"
-	depends on ARCH_INTEGRATOR_AP && n
-	depends on ARCH_MULTI_V5
-	select CPU_ARM1020
-
-config INTEGRATOR_CM10200E
-	bool "Integrator/CM10200E core module"
-	depends on ARCH_INTEGRATOR_AP && n
-	depends on ARCH_MULTI_V5
-	select CPU_ARM1020E
-
-config INTEGRATOR_CM10220E
-	bool "Integrator/CM10220E core module"
-	depends on ARCH_INTEGRATOR_AP
-	depends on ARCH_MULTI_V5
-	select CPU_ARM1022
-
-config INTEGRATOR_CM1026EJS
-	bool "Integrator/CM1026EJ-S core module"
-	depends on ARCH_INTEGRATOR_AP
-	depends on ARCH_MULTI_V5
-	select CPU_ARM1026
-
-config INTEGRATOR_CM1136JFS
-	bool "Integrator/CM1136JF-S core module"
-	depends on ARCH_INTEGRATOR_AP
-	depends on ARCH_MULTI_V6
-	select CPU_V6
-
-config ARCH_INTEGRATOR_CP
-	bool "Support Integrator/CP platform"
-	depends on (!MMU || ARCH_MULTI_V5 || ARCH_MULTI_V6)
-	select ARM_TIMER_SP804
-	select SERIAL_AMBA_PL011 if TTY
-	select SERIAL_AMBA_PL011_CONSOLE if TTY
-	select SOC_BUS
-	help
-	  Include support for the ARM(R) Integrator CP platform.
-
-config INTEGRATOR_CT7T
-	bool "Integrator/CT7TD (ARM7TDMI) core tile"
-	depends on ARCH_INTEGRATOR_CP
-	depends on ARCH_MULTI_V4T && !MMU
-	select CPU_ARM7TDMI
-
-config INTEGRATOR_CT926
-	bool "Integrator/CT926 (ARM926EJ-S) core tile"
-	depends on ARCH_INTEGRATOR_CP
-	depends on ARCH_MULTI_V5
-	select CPU_ARM926T
-
-config INTEGRATOR_CTB36
-	bool "Integrator/CTB36 (ARM1136JF-S) core tile"
-	depends on ARCH_INTEGRATOR_CP
-	depends on ARCH_MULTI_V6
-	select CPU_V6
-
-config ARCH_CINTEGRATOR
-	depends on ARCH_INTEGRATOR_CP
-	def_bool y
-
-endif
diff --git a/arch/arm/mach-integrator/Makefile b/arch/arm/mach-integrator/Makefile
deleted file mode 100644
index 7857a55c90b0..000000000000
--- a/arch/arm/mach-integrator/Makefile
+++ /dev/null
@@ -1,10 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0
-#
-# Makefile for the linux kernel.
-#
-
-# Object file lists.
-
-obj-y					:= core.o
-obj-$(CONFIG_ARCH_INTEGRATOR_AP)	+= integrator_ap.o
-obj-$(CONFIG_ARCH_INTEGRATOR_CP)	+= integrator_cp.o
diff --git a/arch/arm/mach-integrator/core.c b/arch/arm/mach-integrator/core.c
deleted file mode 100644
index 0fe5e1dc9d89..000000000000
--- a/arch/arm/mach-integrator/core.c
+++ /dev/null
@@ -1,96 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- *  linux/arch/arm/mach-integrator/core.c
- *
- *  Copyright (C) 2000-2003 Deep Blue Solutions Ltd
- */
-#include <linux/types.h>
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/device.h>
-#include <linux/export.h>
-#include <linux/spinlock.h>
-#include <linux/interrupt.h>
-#include <linux/irq.h>
-#include <linux/memblock.h>
-#include <linux/sched.h>
-#include <linux/smp.h>
-#include <linux/amba/bus.h>
-#include <linux/amba/serial.h>
-#include <linux/io.h>
-#include <linux/stat.h>
-#include <linux/of.h>
-#include <linux/of_address.h>
-#include <linux/pgtable.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/time.h>
-
-#include "hardware.h"
-#include "cm.h"
-#include "common.h"
-
-static DEFINE_RAW_SPINLOCK(cm_lock);
-static void __iomem *cm_base;
-
-/**
- * cm_get - get the value from the CM_CTRL register
- */
-u32 cm_get(void)
-{
-	return readl(cm_base + INTEGRATOR_HDR_CTRL_OFFSET);
-}
-
-/**
- * cm_control - update the CM_CTRL register.
- * @mask: bits to change
- * @set: bits to set
- */
-void cm_control(u32 mask, u32 set)
-{
-	unsigned long flags;
-	u32 val;
-
-	raw_spin_lock_irqsave(&cm_lock, flags);
-	val = readl(cm_base + INTEGRATOR_HDR_CTRL_OFFSET) & ~mask;
-	writel(val | set, cm_base + INTEGRATOR_HDR_CTRL_OFFSET);
-	raw_spin_unlock_irqrestore(&cm_lock, flags);
-}
-
-void cm_clear_irqs(void)
-{
-	/* disable core module IRQs */
-	writel(0xffffffffU, cm_base + INTEGRATOR_HDR_IC_OFFSET +
-		IRQ_ENABLE_CLEAR);
-}
-
-static const struct of_device_id cm_match[] = {
-	{ .compatible = "arm,core-module-integrator"},
-	{ },
-};
-
-void cm_init(void)
-{
-	struct device_node *cm = of_find_matching_node(NULL, cm_match);
-
-	if (!cm) {
-		pr_crit("no core module node found in device tree\n");
-		return;
-	}
-	cm_base = of_iomap(cm, 0);
-	if (!cm_base) {
-		pr_crit("could not remap core module\n");
-		return;
-	}
-	cm_clear_irqs();
-}
-
-/*
- * We need to stop things allocating the low memory; ideally we need a
- * better implementation of GFP_DMA which does not assume that DMA-able
- * memory starts at zero.
- */
-void __init integrator_reserve(void)
-{
-	memblock_reserve(PHYS_OFFSET, __pa(swapper_pg_dir) - PHYS_OFFSET);
-}
diff --git a/arch/arm/mach-integrator/hardware.h b/arch/arm/mach-integrator/hardware.h
deleted file mode 100644
index 4d6ade3dd4ee..000000000000
--- a/arch/arm/mach-integrator/hardware.h
+++ /dev/null
@@ -1,341 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-or-later */
-/*
- *  This file contains the hardware definitions of the Integrator.
- *
- *  Copyright (C) 1998-1999 ARM Limited.
- */
-#ifndef INTEGRATOR_HARDWARE_H
-#define INTEGRATOR_HARDWARE_H
-
-/*
- * Where in virtual memory the IO devices (timers, system controllers
- * and so on)
- */
-#define IO_BASE			0xF0000000                 // VA of IO
-#define IO_SIZE			0x0B000000                 // How much?
-#define IO_START		INTEGRATOR_HDR_BASE        // PA of IO
-
-/* macro to get at IO space when running virtually */
-#ifdef CONFIG_MMU
-#define IO_ADDRESS(x)	(((x) & 0x000fffff) | (((x) >> 4) & 0x0ff00000) | IO_BASE)
-#else
-#define IO_ADDRESS(x)	(x)
-#endif
-
-#define __io_address(n)		((void __iomem *)IO_ADDRESS(n))
-
-/*
- *  Integrator memory map
- */
-#define INTEGRATOR_BOOT_ROM_LO          0x00000000
-#define INTEGRATOR_BOOT_ROM_HI          0x20000000
-#define INTEGRATOR_BOOT_ROM_BASE        INTEGRATOR_BOOT_ROM_HI	 /*  Normal position */
-#define INTEGRATOR_BOOT_ROM_SIZE        SZ_512K
-
-/*
- * New Core Modules have different amounts of SSRAM, the amount of SSRAM
- * fitted can be found in HDR_STAT.
- *
- * The symbol INTEGRATOR_SSRAM_SIZE is kept, however this now refers to
- * the minimum amount of SSRAM fitted on any core module.
- *
- * New Core Modules also alias the SSRAM.
- *
- */
-#define INTEGRATOR_SSRAM_BASE           0x00000000
-#define INTEGRATOR_SSRAM_ALIAS_BASE     0x10800000
-#define INTEGRATOR_SSRAM_SIZE           SZ_256K
-
-#define INTEGRATOR_FLASH_BASE           0x24000000
-#define INTEGRATOR_FLASH_SIZE           SZ_32M
-
-#define INTEGRATOR_MBRD_SSRAM_BASE      0x28000000
-#define INTEGRATOR_MBRD_SSRAM_SIZE      SZ_512K
-
-/*
- *  SDRAM is a SIMM therefore the size is not known.
- */
-#define INTEGRATOR_SDRAM_BASE           0x00040000
-
-#define INTEGRATOR_SDRAM_ALIAS_BASE     0x80000000
-#define INTEGRATOR_HDR0_SDRAM_BASE      0x80000000
-#define INTEGRATOR_HDR1_SDRAM_BASE      0x90000000
-#define INTEGRATOR_HDR2_SDRAM_BASE      0xA0000000
-#define INTEGRATOR_HDR3_SDRAM_BASE      0xB0000000
-
-/*
- *  Logic expansion modules
- *
- */
-#define INTEGRATOR_LOGIC_MODULES_BASE   0xC0000000
-#define INTEGRATOR_LOGIC_MODULE0_BASE   0xC0000000
-#define INTEGRATOR_LOGIC_MODULE1_BASE   0xD0000000
-#define INTEGRATOR_LOGIC_MODULE2_BASE   0xE0000000
-#define INTEGRATOR_LOGIC_MODULE3_BASE   0xF0000000
-
-/*
- * Integrator header card registers
- */
-#define INTEGRATOR_HDR_ID_OFFSET        0x00
-#define INTEGRATOR_HDR_PROC_OFFSET      0x04
-#define INTEGRATOR_HDR_OSC_OFFSET       0x08
-#define INTEGRATOR_HDR_CTRL_OFFSET      0x0C
-#define INTEGRATOR_HDR_STAT_OFFSET      0x10
-#define INTEGRATOR_HDR_LOCK_OFFSET      0x14
-#define INTEGRATOR_HDR_SDRAM_OFFSET     0x20
-#define INTEGRATOR_HDR_INIT_OFFSET      0x24	 /*  CM9x6 */
-#define INTEGRATOR_HDR_IC_OFFSET        0x40
-#define INTEGRATOR_HDR_SPDBASE_OFFSET   0x100
-#define INTEGRATOR_HDR_SPDTOP_OFFSET    0x200
-
-#define INTEGRATOR_HDR_BASE             0x10000000
-#define INTEGRATOR_HDR_ID               (INTEGRATOR_HDR_BASE + INTEGRATOR_HDR_ID_OFFSET)
-#define INTEGRATOR_HDR_PROC             (INTEGRATOR_HDR_BASE + INTEGRATOR_HDR_PROC_OFFSET)
-#define INTEGRATOR_HDR_OSC              (INTEGRATOR_HDR_BASE + INTEGRATOR_HDR_OSC_OFFSET)
-#define INTEGRATOR_HDR_CTRL             (INTEGRATOR_HDR_BASE + INTEGRATOR_HDR_CTRL_OFFSET)
-#define INTEGRATOR_HDR_STAT             (INTEGRATOR_HDR_BASE + INTEGRATOR_HDR_STAT_OFFSET)
-#define INTEGRATOR_HDR_LOCK             (INTEGRATOR_HDR_BASE + INTEGRATOR_HDR_LOCK_OFFSET)
-#define INTEGRATOR_HDR_SDRAM            (INTEGRATOR_HDR_BASE + INTEGRATOR_HDR_SDRAM_OFFSET)
-#define INTEGRATOR_HDR_INIT             (INTEGRATOR_HDR_BASE + INTEGRATOR_HDR_INIT_OFFSET)
-#define INTEGRATOR_HDR_IC               (INTEGRATOR_HDR_BASE + INTEGRATOR_HDR_IC_OFFSET)
-#define INTEGRATOR_HDR_SPDBASE          (INTEGRATOR_HDR_BASE + INTEGRATOR_HDR_SPDBASE_OFFSET)
-#define INTEGRATOR_HDR_SPDTOP           (INTEGRATOR_HDR_BASE + INTEGRATOR_HDR_SPDTOP_OFFSET)
-
-#define INTEGRATOR_HDR_CTRL_LED         0x01
-#define INTEGRATOR_HDR_CTRL_MBRD_DETECH 0x02
-#define INTEGRATOR_HDR_CTRL_REMAP       0x04
-#define INTEGRATOR_HDR_CTRL_RESET       0x08
-#define INTEGRATOR_HDR_CTRL_HIGHVECTORS 0x10
-#define INTEGRATOR_HDR_CTRL_BIG_ENDIAN  0x20
-#define INTEGRATOR_HDR_CTRL_FASTBUS     0x40
-#define INTEGRATOR_HDR_CTRL_SYNC        0x80
-
-#define INTEGRATOR_HDR_OSC_CORE_10MHz   0x102
-#define INTEGRATOR_HDR_OSC_CORE_15MHz   0x107
-#define INTEGRATOR_HDR_OSC_CORE_20MHz   0x10C
-#define INTEGRATOR_HDR_OSC_CORE_25MHz   0x111
-#define INTEGRATOR_HDR_OSC_CORE_30MHz   0x116
-#define INTEGRATOR_HDR_OSC_CORE_35MHz   0x11B
-#define INTEGRATOR_HDR_OSC_CORE_40MHz   0x120
-#define INTEGRATOR_HDR_OSC_CORE_45MHz   0x125
-#define INTEGRATOR_HDR_OSC_CORE_50MHz   0x12A
-#define INTEGRATOR_HDR_OSC_CORE_55MHz   0x12F
-#define INTEGRATOR_HDR_OSC_CORE_60MHz   0x134
-#define INTEGRATOR_HDR_OSC_CORE_65MHz   0x139
-#define INTEGRATOR_HDR_OSC_CORE_70MHz   0x13E
-#define INTEGRATOR_HDR_OSC_CORE_75MHz   0x143
-#define INTEGRATOR_HDR_OSC_CORE_80MHz   0x148
-#define INTEGRATOR_HDR_OSC_CORE_85MHz   0x14D
-#define INTEGRATOR_HDR_OSC_CORE_90MHz   0x152
-#define INTEGRATOR_HDR_OSC_CORE_95MHz   0x157
-#define INTEGRATOR_HDR_OSC_CORE_100MHz  0x15C
-#define INTEGRATOR_HDR_OSC_CORE_105MHz  0x161
-#define INTEGRATOR_HDR_OSC_CORE_110MHz  0x166
-#define INTEGRATOR_HDR_OSC_CORE_115MHz  0x16B
-#define INTEGRATOR_HDR_OSC_CORE_120MHz  0x170
-#define INTEGRATOR_HDR_OSC_CORE_125MHz  0x175
-#define INTEGRATOR_HDR_OSC_CORE_130MHz  0x17A
-#define INTEGRATOR_HDR_OSC_CORE_135MHz  0x17F
-#define INTEGRATOR_HDR_OSC_CORE_140MHz  0x184
-#define INTEGRATOR_HDR_OSC_CORE_145MHz  0x189
-#define INTEGRATOR_HDR_OSC_CORE_150MHz  0x18E
-#define INTEGRATOR_HDR_OSC_CORE_155MHz  0x193
-#define INTEGRATOR_HDR_OSC_CORE_160MHz  0x198
-#define INTEGRATOR_HDR_OSC_CORE_MASK    0x7FF
-
-#define INTEGRATOR_HDR_OSC_MEM_10MHz    0x10C000
-#define INTEGRATOR_HDR_OSC_MEM_15MHz    0x116000
-#define INTEGRATOR_HDR_OSC_MEM_20MHz    0x120000
-#define INTEGRATOR_HDR_OSC_MEM_25MHz    0x12A000
-#define INTEGRATOR_HDR_OSC_MEM_30MHz    0x134000
-#define INTEGRATOR_HDR_OSC_MEM_33MHz    0x13A000
-#define INTEGRATOR_HDR_OSC_MEM_40MHz    0x148000
-#define INTEGRATOR_HDR_OSC_MEM_50MHz    0x15C000
-#define INTEGRATOR_HDR_OSC_MEM_60MHz    0x170000
-#define INTEGRATOR_HDR_OSC_MEM_66MHz    0x17C000
-#define INTEGRATOR_HDR_OSC_MEM_MASK     0x7FF000
-
-#define INTEGRATOR_HDR_OSC_BUS_MODE_CM7x0  0x0
-#define INTEGRATOR_HDR_OSC_BUS_MODE_CM9x0  0x0800000
-#define INTEGRATOR_HDR_OSC_BUS_MODE_CM9x6  0x1000000
-#define INTEGRATOR_HDR_OSC_BUS_MODE_CM10x00  0x1800000
-#define INTEGRATOR_HDR_OSC_BUS_MODE_MASK  0x1800000
-
-#define INTEGRATOR_HDR_SDRAM_SPD_OK     (1 << 5)
-
-/*
- * Integrator system registers
- */
-
-/*
- *  System Controller
- */
-#define INTEGRATOR_SC_ID_OFFSET         0x00
-#define INTEGRATOR_SC_OSC_OFFSET        0x04
-#define INTEGRATOR_SC_CTRLS_OFFSET      0x08
-#define INTEGRATOR_SC_CTRLC_OFFSET      0x0C
-#define INTEGRATOR_SC_DEC_OFFSET        0x10
-#define INTEGRATOR_SC_ARB_OFFSET        0x14
-#define INTEGRATOR_SC_LOCK_OFFSET       0x1C
-
-#define INTEGRATOR_SC_BASE              0x11000000
-#define INTEGRATOR_SC_ID                (INTEGRATOR_SC_BASE + INTEGRATOR_SC_ID_OFFSET)
-#define INTEGRATOR_SC_OSC               (INTEGRATOR_SC_BASE + INTEGRATOR_SC_OSC_OFFSET)
-#define INTEGRATOR_SC_CTRLS             (INTEGRATOR_SC_BASE + INTEGRATOR_SC_CTRLS_OFFSET)
-#define INTEGRATOR_SC_CTRLC             (INTEGRATOR_SC_BASE + INTEGRATOR_SC_CTRLC_OFFSET)
-#define INTEGRATOR_SC_DEC               (INTEGRATOR_SC_BASE + INTEGRATOR_SC_DEC_OFFSET)
-#define INTEGRATOR_SC_ARB               (INTEGRATOR_SC_BASE + INTEGRATOR_SC_ARB_OFFSET)
-#define INTEGRATOR_SC_PCIENABLE         (INTEGRATOR_SC_BASE + INTEGRATOR_SC_PCIENABLE_OFFSET)
-#define INTEGRATOR_SC_LOCK              (INTEGRATOR_SC_BASE + INTEGRATOR_SC_LOCK_OFFSET)
-
-#define INTEGRATOR_SC_OSC_SYS_10MHz     0x20
-#define INTEGRATOR_SC_OSC_SYS_15MHz     0x34
-#define INTEGRATOR_SC_OSC_SYS_20MHz     0x48
-#define INTEGRATOR_SC_OSC_SYS_25MHz     0x5C
-#define INTEGRATOR_SC_OSC_SYS_33MHz     0x7C
-#define INTEGRATOR_SC_OSC_SYS_MASK      0xFF
-
-#define INTEGRATOR_SC_OSC_PCI_25MHz     0x100
-#define INTEGRATOR_SC_OSC_PCI_33MHz     0x0
-#define INTEGRATOR_SC_OSC_PCI_MASK      0x100
-
-#define INTEGRATOR_SC_CTRL_SOFTRST      (1 << 0)
-#define INTEGRATOR_SC_CTRL_nFLVPPEN     (1 << 1)
-#define INTEGRATOR_SC_CTRL_nFLWP        (1 << 2)
-#define INTEGRATOR_SC_CTRL_URTS0        (1 << 4)
-#define INTEGRATOR_SC_CTRL_UDTR0        (1 << 5)
-#define INTEGRATOR_SC_CTRL_URTS1        (1 << 6)
-#define INTEGRATOR_SC_CTRL_UDTR1        (1 << 7)
-
-/*
- *  External Bus Interface
- */
-#define INTEGRATOR_EBI_BASE             0x12000000
-
-#define INTEGRATOR_EBI_CSR0_OFFSET      0x00
-#define INTEGRATOR_EBI_CSR1_OFFSET      0x04
-#define INTEGRATOR_EBI_CSR2_OFFSET      0x08
-#define INTEGRATOR_EBI_CSR3_OFFSET      0x0C
-#define INTEGRATOR_EBI_LOCK_OFFSET      0x20
-
-#define INTEGRATOR_EBI_CSR0             (INTEGRATOR_EBI_BASE + INTEGRATOR_EBI_CSR0_OFFSET)
-#define INTEGRATOR_EBI_CSR1             (INTEGRATOR_EBI_BASE + INTEGRATOR_EBI_CSR1_OFFSET)
-#define INTEGRATOR_EBI_CSR2             (INTEGRATOR_EBI_BASE + INTEGRATOR_EBI_CSR2_OFFSET)
-#define INTEGRATOR_EBI_CSR3             (INTEGRATOR_EBI_BASE + INTEGRATOR_EBI_CSR3_OFFSET)
-#define INTEGRATOR_EBI_LOCK             (INTEGRATOR_EBI_BASE + INTEGRATOR_EBI_LOCK_OFFSET)
-
-#define INTEGRATOR_EBI_8_BIT            0x00
-#define INTEGRATOR_EBI_16_BIT           0x01
-#define INTEGRATOR_EBI_32_BIT           0x02
-#define INTEGRATOR_EBI_WRITE_ENABLE     0x04
-#define INTEGRATOR_EBI_SYNC             0x08
-#define INTEGRATOR_EBI_WS_2             0x00
-#define INTEGRATOR_EBI_WS_3             0x10
-#define INTEGRATOR_EBI_WS_4             0x20
-#define INTEGRATOR_EBI_WS_5             0x30
-#define INTEGRATOR_EBI_WS_6             0x40
-#define INTEGRATOR_EBI_WS_7             0x50
-#define INTEGRATOR_EBI_WS_8             0x60
-#define INTEGRATOR_EBI_WS_9             0x70
-#define INTEGRATOR_EBI_WS_10            0x80
-#define INTEGRATOR_EBI_WS_11            0x90
-#define INTEGRATOR_EBI_WS_12            0xA0
-#define INTEGRATOR_EBI_WS_13            0xB0
-#define INTEGRATOR_EBI_WS_14            0xC0
-#define INTEGRATOR_EBI_WS_15            0xD0
-#define INTEGRATOR_EBI_WS_16            0xE0
-#define INTEGRATOR_EBI_WS_17            0xF0
-
-
-#define INTEGRATOR_CT_BASE              0x13000000	 /*  Counter/Timers */
-#define INTEGRATOR_IC_BASE              0x14000000	 /*  Interrupt Controller */
-#define INTEGRATOR_RTC_BASE             0x15000000	 /*  Real Time Clock */
-#define INTEGRATOR_UART0_BASE           0x16000000	 /*  UART 0 */
-#define INTEGRATOR_UART1_BASE           0x17000000	 /*  UART 1 */
-#define INTEGRATOR_KBD_BASE             0x18000000	 /*  Keyboard */
-#define INTEGRATOR_MOUSE_BASE           0x19000000	 /*  Mouse */
-
-/*
- *  LED's & Switches
- */
-#define INTEGRATOR_DBG_ALPHA_OFFSET     0x00
-#define INTEGRATOR_DBG_LEDS_OFFSET      0x04
-#define INTEGRATOR_DBG_SWITCH_OFFSET    0x08
-
-#define INTEGRATOR_DBG_BASE             0x1A000000
-#define INTEGRATOR_DBG_ALPHA            (INTEGRATOR_DBG_BASE + INTEGRATOR_DBG_ALPHA_OFFSET)
-#define INTEGRATOR_DBG_LEDS             (INTEGRATOR_DBG_BASE + INTEGRATOR_DBG_LEDS_OFFSET)
-#define INTEGRATOR_DBG_SWITCH           (INTEGRATOR_DBG_BASE + INTEGRATOR_DBG_SWITCH_OFFSET)
-
-#define INTEGRATOR_AP_GPIO_BASE		0x1B000000	/* GPIO */
-
-#define INTEGRATOR_CP_MMC_BASE		0x1C000000	/* MMC */
-#define INTEGRATOR_CP_AACI_BASE		0x1D000000	/* AACI */
-#define INTEGRATOR_CP_ETH_BASE		0xC8000000	/* Ethernet */
-#define INTEGRATOR_CP_GPIO_BASE		0xC9000000	/* GPIO */
-#define INTEGRATOR_CP_SIC_BASE		0xCA000000	/* SIC */
-#define INTEGRATOR_CP_CTL_BASE		0xCB000000	/* CP system control */
-
-/* PS2 Keyboard interface */
-#define KMI0_BASE                       INTEGRATOR_KBD_BASE
-
-/* PS2 Mouse interface */
-#define KMI1_BASE                       INTEGRATOR_MOUSE_BASE
-
-/*
- * Integrator Interrupt Controllers
- *
- *
- * Offsets from interrupt controller base
- *
- * System Controller interrupt controller base is
- *
- * 	INTEGRATOR_IC_BASE + (header_number << 6)
- *
- * Core Module interrupt controller base is
- *
- * 	INTEGRATOR_HDR_IC
- */
-#define IRQ_STATUS                      0
-#define IRQ_RAW_STATUS                  0x04
-#define IRQ_ENABLE                      0x08
-#define IRQ_ENABLE_SET                  0x08
-#define IRQ_ENABLE_CLEAR                0x0C
-
-#define INT_SOFT_SET                    0x10
-#define INT_SOFT_CLEAR                  0x14
-
-#define FIQ_STATUS                      0x20
-#define FIQ_RAW_STATUS                  0x24
-#define FIQ_ENABLE                      0x28
-#define FIQ_ENABLE_SET                  0x28
-#define FIQ_ENABLE_CLEAR                0x2C
-
-
-/*
- * LED's
- */
-#define GREEN_LED                       0x01
-#define YELLOW_LED                      0x02
-#define RED_LED                         0x04
-#define GREEN_LED_2                     0x08
-#define ALL_LEDS                        0x0F
-
-#define LED_BANK                        INTEGRATOR_DBG_LEDS
-
-/*
- *  Timer definitions
- *
- *  Only use timer 1 & 2
- *  (both run at 24MHz and will need the clock divider set to 16).
- *
- *  Timer 0 runs at bus frequency
- */
-#define INTEGRATOR_TIMER0_BASE          INTEGRATOR_CT_BASE
-#define INTEGRATOR_TIMER1_BASE          (INTEGRATOR_CT_BASE + 0x100)
-#define INTEGRATOR_TIMER2_BASE          (INTEGRATOR_CT_BASE + 0x200)
-
-#define INTEGRATOR_CSR_BASE             0x10000000
-#define INTEGRATOR_CSR_SIZE             0x10000000
-
-#endif /* INTEGRATOR_HARDWARE_H */
diff --git a/arch/arm/mach-iop32x/Kconfig b/arch/arm/mach-iop32x/Kconfig
index f1f342cb0509..761fbb04faa1 100644
--- a/arch/arm/mach-iop32x/Kconfig
+++ b/arch/arm/mach-iop32x/Kconfig
@@ -1,9 +1,18 @@
 # SPDX-License-Identifier: GPL-2.0
-if ARCH_IOP32X
-
-menu "IOP32x Implementation Options"
+menuconfig ARCH_IOP32X
+	bool "IOP32x-based platforms"
+	depends on ARCH_MULTI_V5
+	depends on CPU_LITTLE_ENDIAN
+	depends on ATAGS && UNUSED_BOARD_FILES
+	select CPU_XSCALE
+	select GPIO_IOP
+	select GPIOLIB
+	select FORCE_PCI
+	help
+	  Support for Intel's 80219 and IOP32X (XScale) family of
+	  processors.
 
-comment "IOP32x Platform Types"
+if ARCH_IOP32X
 
 config MACH_EP80219
 	bool
@@ -42,6 +51,4 @@ config MACH_EM7210
 	  board. Say also Y here if you have a SS4000e Baxter Creek NAS
 	  appliance."
 
-endmenu
-
 endif
diff --git a/arch/arm/mach-iop32x/Makefile.boot b/arch/arm/mach-iop32x/Makefile.boot
deleted file mode 100644
index 5c3af01c4000..000000000000
--- a/arch/arm/mach-iop32x/Makefile.boot
+++ /dev/null
@@ -1,4 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0-only
-   zreladdr-y	+= 0xa0008000
-params_phys-y	:= 0xa0000100
-initrd_phys-y	:= 0xa0800000
diff --git a/arch/arm/mach-iop32x/cp6.c b/arch/arm/mach-iop32x/cp6.c
index ec74b07fb7e3..7135a0ac9949 100644
--- a/arch/arm/mach-iop32x/cp6.c
+++ b/arch/arm/mach-iop32x/cp6.c
@@ -7,7 +7,9 @@
 #include <asm/traps.h>
 #include <asm/ptrace.h>
 
-static int cp6_trap(struct pt_regs *regs, unsigned int instr)
+#include "iop3xx.h"
+
+void iop_enable_cp6(void)
 {
 	u32 temp;
 
@@ -16,7 +18,15 @@ static int cp6_trap(struct pt_regs *regs, unsigned int instr)
 		"mrc	p15, 0, %0, c15, c1, 0\n\t"
 		"orr	%0, %0, #(1 << 6)\n\t"
 		"mcr	p15, 0, %0, c15, c1, 0\n\t"
+		"mrc	p15, 0, %0, c15, c1, 0\n\t"
+		"mov	%0, %0\n\t"
+		"sub	pc, pc, #4  @ cp_wait\n\t"
 		: "=r"(temp));
+}
+
+static int cp6_trap(struct pt_regs *regs, unsigned int instr)
+{
+	iop_enable_cp6();
 
 	return 0;
 }
diff --git a/arch/arm/mach-iop32x/em7210.c b/arch/arm/mach-iop32x/em7210.c
index d43ced3cd4e7..ac130aba5a6e 100644
--- a/arch/arm/mach-iop32x/em7210.c
+++ b/arch/arm/mach-iop32x/em7210.c
@@ -223,6 +223,7 @@ static void __init em7210_init_machine(void)
 
 MACHINE_START(EM7210, "Lanner EM7210")
 	.atag_offset	= 0x100,
+	.nr_irqs	= IOP32X_NR_IRQS,
 	.map_io		= em7210_map_io,
 	.init_irq	= iop32x_init_irq,
 	.init_time	= em7210_timer_init,
diff --git a/arch/arm/mach-iop32x/glantank.c b/arch/arm/mach-iop32x/glantank.c
index 2fe0f77d1f1d..cd6e7da2ea10 100644
--- a/arch/arm/mach-iop32x/glantank.c
+++ b/arch/arm/mach-iop32x/glantank.c
@@ -205,6 +205,7 @@ static void __init glantank_init_machine(void)
 MACHINE_START(GLANTANK, "GLAN Tank")
 	/* Maintainer: Lennert Buytenhek <buytenh@wantstofly.org> */
 	.atag_offset	= 0x100,
+	.nr_irqs	= IOP32X_NR_IRQS,
 	.map_io		= glantank_map_io,
 	.init_irq	= iop32x_init_irq,
 	.init_time	= glantank_timer_init,
diff --git a/arch/arm/mach-iop32x/include/mach/entry-macro.S b/arch/arm/mach-iop32x/include/mach/entry-macro.S
deleted file mode 100644
index 8e6766d4621e..000000000000
--- a/arch/arm/mach-iop32x/include/mach/entry-macro.S
+++ /dev/null
@@ -1,31 +0,0 @@
-/*
- * arch/arm/mach-iop32x/include/mach/entry-macro.S
- *
- * Low-level IRQ helper macros for IOP32x-based platforms
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-	.macro get_irqnr_preamble, base, tmp
-	mrc	p15, 0, \tmp, c15, c1, 0
-	orr	\tmp, \tmp, #(1 << 6)
-	mcr	p15, 0, \tmp, c15, c1, 0	@ Enable cp6 access
-	mrc	p15, 0, \tmp, c15, c1, 0
-	mov	\tmp, \tmp
-	sub	pc, pc, #4			@ cp_wait
-	.endm
-
-	.macro  get_irqnr_and_base, irqnr, irqstat, base, tmp
-	mrc     p6, 0, \irqstat, c8, c0, 0	@ Read IINTSRC
-	cmp     \irqstat, #0
-	clzne   \irqnr, \irqstat
-	rsbne   \irqnr, \irqnr, #31
-	.endm
-
-	.macro arch_ret_to_user, tmp1, tmp2
-	mrc	p15, 0, \tmp1, c15, c1, 0
-	ands	\tmp2, \tmp1, #(1 << 6)
-	bicne	\tmp1, \tmp1, #(1 << 6)
-	mcrne	p15, 0, \tmp1, c15, c1, 0	@ Disable cp6 access
-	.endm
diff --git a/arch/arm/mach-iop32x/include/mach/irqs.h b/arch/arm/mach-iop32x/include/mach/irqs.h
deleted file mode 100644
index c4e78df428e8..000000000000
--- a/arch/arm/mach-iop32x/include/mach/irqs.h
+++ /dev/null
@@ -1,14 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-only */
-/*
- * arch/arm/mach-iop32x/include/mach/irqs.h
- *
- * Author:	Rory Bolt <rorybolt@pacbell.net>
- * Copyright:	(C) 2002 Rory Bolt
- */
-
-#ifndef __IRQS_H
-#define __IRQS_H
-
-#define NR_IRQS			32
-
-#endif
diff --git a/arch/arm/mach-iop32x/include/mach/uncompress.h b/arch/arm/mach-iop32x/include/mach/uncompress.h
deleted file mode 100644
index c8548875d942..000000000000
--- a/arch/arm/mach-iop32x/include/mach/uncompress.h
+++ /dev/null
@@ -1,25 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-/*
- * arch/arm/mach-iop32x/include/mach/uncompress.h
- */
-
-#include <asm/types.h>
-#include <asm/mach-types.h>
-#include <linux/serial_reg.h>
-
-#define uart_base ((volatile u8 *)0xfe800000)
-
-#define TX_DONE		(UART_LSR_TEMT | UART_LSR_THRE)
-
-static inline void putc(char c)
-{
-	while ((uart_base[UART_LSR] & TX_DONE) != TX_DONE)
-		barrier();
-	uart_base[UART_TX] = c;
-}
-
-static inline void flush(void)
-{
-}
-
-#define arch_decomp_setup() do { } while (0)
diff --git a/arch/arm/mach-iop32x/iop3xx.h b/arch/arm/mach-iop32x/iop3xx.h
index 46b4b34a4ad2..a6ec7ebadb35 100644
--- a/arch/arm/mach-iop32x/iop3xx.h
+++ b/arch/arm/mach-iop32x/iop3xx.h
@@ -225,6 +225,7 @@ extern int iop3xx_get_init_atu(void);
 #include <linux/reboot.h>
 
 void iop3xx_map_io(void);
+void iop_enable_cp6(void);
 void iop_init_cp6_handler(void);
 void iop_init_time(unsigned long tickrate);
 void iop3xx_restart(enum reboot_mode, const char *);
diff --git a/arch/arm/mach-iop32x/iq31244.c b/arch/arm/mach-iop32x/iq31244.c
index 49caaa703881..8b4c29d17265 100644
--- a/arch/arm/mach-iop32x/iq31244.c
+++ b/arch/arm/mach-iop32x/iq31244.c
@@ -324,6 +324,7 @@ MACHINE_END
 MACHINE_START(EP80219, "Intel EP80219")
 	/* Maintainer: Intel Corp. */
 	.atag_offset	= 0x100,
+	.nr_irqs	= IOP32X_NR_IRQS,
 	.map_io		= iq31244_map_io,
 	.init_irq	= iop32x_init_irq,
 	.init_time	= iq31244_timer_init,
diff --git a/arch/arm/mach-iop32x/iq80321.c b/arch/arm/mach-iop32x/iq80321.c
index b455d7073296..d9780c4660cb 100644
--- a/arch/arm/mach-iop32x/iq80321.c
+++ b/arch/arm/mach-iop32x/iq80321.c
@@ -183,6 +183,7 @@ static void __init iq80321_init_machine(void)
 MACHINE_START(IQ80321, "Intel IQ80321")
 	/* Maintainer: Intel Corp. */
 	.atag_offset	= 0x100,
+	.nr_irqs	= IOP32X_NR_IRQS,
 	.map_io		= iq80321_map_io,
 	.init_irq	= iop32x_init_irq,
 	.init_time	= iq80321_timer_init,
diff --git a/arch/arm/mach-iop32x/irq.c b/arch/arm/mach-iop32x/irq.c
index 2d48bf1398c1..6dca7e97d81f 100644
--- a/arch/arm/mach-iop32x/irq.c
+++ b/arch/arm/mach-iop32x/irq.c
@@ -29,17 +29,26 @@ static void intstr_write(u32 val)
 	asm volatile("mcr p6, 0, %0, c4, c0, 0" : : "r" (val));
 }
 
+static u32 iintsrc_read(void)
+{
+	int irq;
+
+	asm volatile("mrc p6, 0, %0, c8, c0, 0" : "=r" (irq));
+
+	return irq;
+}
+
 static void
 iop32x_irq_mask(struct irq_data *d)
 {
-	iop32x_mask &= ~(1 << d->irq);
+	iop32x_mask &= ~(1 << (d->irq - 1));
 	intctl_write(iop32x_mask);
 }
 
 static void
 iop32x_irq_unmask(struct irq_data *d)
 {
-	iop32x_mask |= 1 << d->irq;
+	iop32x_mask |= 1 << (d->irq - 1);
 	intctl_write(iop32x_mask);
 }
 
@@ -50,11 +59,25 @@ struct irq_chip ext_chip = {
 	.irq_unmask	= iop32x_irq_unmask,
 };
 
+static void iop_handle_irq(struct pt_regs *regs)
+{
+	u32 mask;
+
+	iop_enable_cp6();
+
+	do {
+		mask = iintsrc_read();
+		if (mask)
+			generic_handle_irq(fls(mask));
+	} while (mask);
+}
+
 void __init iop32x_init_irq(void)
 {
 	int i;
 
 	iop_init_cp6_handler();
+	set_handle_irq(iop_handle_irq);
 
 	intctl_write(0);
 	intstr_write(0);
@@ -65,7 +88,7 @@ void __init iop32x_init_irq(void)
 	    machine_is_em7210())
 		*IOP3XX_PCIIRSR = 0x0f;
 
-	for (i = 0; i < NR_IRQS; i++) {
+	for (i = 1; i < NR_IRQS; i++) {
 		irq_set_chip_and_handler(i, &ext_chip, handle_level_irq);
 		irq_clear_status_flags(i, IRQ_NOREQUEST | IRQ_NOPROBE);
 	}
diff --git a/arch/arm/mach-iop32x/irqs.h b/arch/arm/mach-iop32x/irqs.h
index 69858e4e905d..e9fc88e09189 100644
--- a/arch/arm/mach-iop32x/irqs.h
+++ b/arch/arm/mach-iop32x/irqs.h
@@ -7,36 +7,42 @@
 #ifndef __IOP32X_IRQS_H
 #define __IOP32X_IRQS_H
 
+/* Interrupts in Linux start at 1, hardware starts at 0 */
+
+#define IOP_IRQ(x) ((x) + 1)
+
 /*
  * IOP80321 chipset interrupts
  */
-#define IRQ_IOP32X_DMA0_EOT	0
-#define IRQ_IOP32X_DMA0_EOC	1
-#define IRQ_IOP32X_DMA1_EOT	2
-#define IRQ_IOP32X_DMA1_EOC	3
-#define IRQ_IOP32X_AA_EOT	6
-#define IRQ_IOP32X_AA_EOC	7
-#define IRQ_IOP32X_CORE_PMON	8
-#define IRQ_IOP32X_TIMER0	9
-#define IRQ_IOP32X_TIMER1	10
-#define IRQ_IOP32X_I2C_0	11
-#define IRQ_IOP32X_I2C_1	12
-#define IRQ_IOP32X_MESSAGING	13
-#define IRQ_IOP32X_ATU_BIST	14
-#define IRQ_IOP32X_PERFMON	15
-#define IRQ_IOP32X_CORE_PMU	16
-#define IRQ_IOP32X_BIU_ERR	17
-#define IRQ_IOP32X_ATU_ERR	18
-#define IRQ_IOP32X_MCU_ERR	19
-#define IRQ_IOP32X_DMA0_ERR	20
-#define IRQ_IOP32X_DMA1_ERR	21
-#define IRQ_IOP32X_AA_ERR	23
-#define IRQ_IOP32X_MSG_ERR	24
-#define IRQ_IOP32X_SSP		25
-#define IRQ_IOP32X_XINT0	27
-#define IRQ_IOP32X_XINT1	28
-#define IRQ_IOP32X_XINT2	29
-#define IRQ_IOP32X_XINT3	30
-#define IRQ_IOP32X_HPI		31
+#define IRQ_IOP32X_DMA0_EOT	IOP_IRQ(0)
+#define IRQ_IOP32X_DMA0_EOC	IOP_IRQ(1)
+#define IRQ_IOP32X_DMA1_EOT	IOP_IRQ(2)
+#define IRQ_IOP32X_DMA1_EOC	IOP_IRQ(3)
+#define IRQ_IOP32X_AA_EOT	IOP_IRQ(6)
+#define IRQ_IOP32X_AA_EOC	IOP_IRQ(7)
+#define IRQ_IOP32X_CORE_PMON	IOP_IRQ(8)
+#define IRQ_IOP32X_TIMER0	IOP_IRQ(9)
+#define IRQ_IOP32X_TIMER1	IOP_IRQ(10)
+#define IRQ_IOP32X_I2C_0	IOP_IRQ(11)
+#define IRQ_IOP32X_I2C_1	IOP_IRQ(12)
+#define IRQ_IOP32X_MESSAGING	IOP_IRQ(13)
+#define IRQ_IOP32X_ATU_BIST	IOP_IRQ(14)
+#define IRQ_IOP32X_PERFMON	IOP_IRQ(15)
+#define IRQ_IOP32X_CORE_PMU	IOP_IRQ(16)
+#define IRQ_IOP32X_BIU_ERR	IOP_IRQ(17)
+#define IRQ_IOP32X_ATU_ERR	IOP_IRQ(18)
+#define IRQ_IOP32X_MCU_ERR	IOP_IRQ(19)
+#define IRQ_IOP32X_DMA0_ERR	IOP_IRQ(20)
+#define IRQ_IOP32X_DMA1_ERR	IOP_IRQ(21)
+#define IRQ_IOP32X_AA_ERR	IOP_IRQ(23)
+#define IRQ_IOP32X_MSG_ERR	IOP_IRQ(24)
+#define IRQ_IOP32X_SSP		IOP_IRQ(25)
+#define IRQ_IOP32X_XINT0	IOP_IRQ(27)
+#define IRQ_IOP32X_XINT1	IOP_IRQ(28)
+#define IRQ_IOP32X_XINT2	IOP_IRQ(29)
+#define IRQ_IOP32X_XINT3	IOP_IRQ(30)
+#define IRQ_IOP32X_HPI		IOP_IRQ(31)
+
+#define IOP32X_NR_IRQS		(IRQ_IOP32X_HPI + 1)
 
 #endif
diff --git a/arch/arm/mach-iop32x/n2100.c b/arch/arm/mach-iop32x/n2100.c
index bf99e718f8b8..bb1e2e11bf35 100644
--- a/arch/arm/mach-iop32x/n2100.c
+++ b/arch/arm/mach-iop32x/n2100.c
@@ -358,6 +358,7 @@ static void __init n2100_init_machine(void)
 MACHINE_START(N2100, "Thecus N2100")
 	/* Maintainer: Lennert Buytenhek <buytenh@wantstofly.org> */
 	.atag_offset	= 0x100,
+	.nr_irqs	= IOP32X_NR_IRQS,
 	.map_io		= n2100_map_io,
 	.init_irq	= iop32x_init_irq,
 	.init_time	= n2100_timer_init,
diff --git a/arch/arm/mach-iop32x/pci.c b/arch/arm/mach-iop32x/pci.c
index ab0010dc3145..7a215d2ee7e2 100644
--- a/arch/arm/mach-iop32x/pci.c
+++ b/arch/arm/mach-iop32x/pci.c
@@ -185,6 +185,7 @@ iop3xx_pci_abort(unsigned long addr, unsigned int fsr, struct pt_regs *regs)
 int iop3xx_pci_setup(int nr, struct pci_sys_data *sys)
 {
 	struct resource *res;
+	struct resource realio;
 
 	if (nr != 0)
 		return 0;
@@ -206,7 +207,9 @@ int iop3xx_pci_setup(int nr, struct pci_sys_data *sys)
 
 	pci_add_resource_offset(&sys->resources, res, sys->mem_offset);
 
-	pci_ioremap_io(0, IOP3XX_PCI_LOWER_IO_PA);
+	realio.start = 0;
+	realio.end = realio.start + SZ_64K - 1;
+	pci_remap_iospace(&realio, IOP3XX_PCI_LOWER_IO_PA);
 
 	return 1;
 }
diff --git a/arch/arm/mach-ixp4xx/Kconfig b/arch/arm/mach-ixp4xx/Kconfig
index 365a5853d310..cb46802f5ce5 100644
--- a/arch/arm/mach-ixp4xx/Kconfig
+++ b/arch/arm/mach-ixp4xx/Kconfig
@@ -1,92 +1,19 @@
 # SPDX-License-Identifier: GPL-2.0-only
-if ARCH_IXP4XX
-
-menu "Intel IXP4xx Implementation Options"
-
-comment "IXP4xx Platforms"
-
-config MACH_IXP4XX_OF
-	bool
-	prompt "Device Tree IXP4xx boards"
-	default y
+menuconfig ARCH_IXP4XX
+	bool "IXP4xx-based platforms"
+	depends on ARCH_MULTI_V5
+	depends on CPU_BIG_ENDIAN
 	select ARM_APPENDED_DTB # Old Redboot bootloaders deployed
+	select CPU_XSCALE
+	select GPIO_IXP4XX
+	select GPIOLIB
+	select FORCE_PCI
 	select I2C
 	select I2C_IOP3XX
-	select PCI
+	select IXP4XX_IRQ
+	select IXP4XX_TIMER
+	select USB_EHCI_BIG_ENDIAN_DESC
+	select USB_EHCI_BIG_ENDIAN_MMIO
 	select USE_OF
 	help
-	  Say 'Y' here to support Device Tree-based IXP4xx platforms.
-
-config MACH_GATEWAY7001
-	bool "Gateway 7001"
-	depends on IXP4XX_PCI_LEGACY
-	help
-	  Say 'Y' here if you want your kernel to support Gateway's
-	  7001 Access Point. For more information on this platform,
-	  see http://openwrt.org
-
-config MACH_GORAMO_MLR
-	bool "GORAMO Multi Link Router"
-	depends on IXP4XX_PCI_LEGACY
-	help
-	  Say 'Y' here if you want your kernel to support GORAMO
-	  MultiLink router.
-
-config ARCH_PRPMC1100
-	bool "PrPMC1100"
-	help
-	  Say 'Y' here if you want your kernel to support the Motorola
-	  PrPCM1100 Processor Mezanine Module. For more information on
-	  this platform, see <file:Documentation/arm/ixp4xx.rst>.
-
-#
-# Certain registers and IRQs are only enabled if supporting IXP465 CPUs
-#
-config CPU_IXP46X
-	bool
-	depends on MACH_IXDP465
-	default y
-
-config CPU_IXP43X
-	bool
-	depends on MACH_KIXRP435
-	default y
-
-comment "IXP4xx Options"
-
-config IXP4XX_PCI_LEGACY
-	bool "IXP4xx legacy PCI driver support"
-	depends on PCI
-	help
-	  Selects legacy PCI driver.
-	  Not recommended for new development.
-
-config IXP4XX_INDIRECT_PCI
-	bool "Use indirect PCI memory access"
-	depends on IXP4XX_PCI_LEGACY
-	help
-          IXP4xx provides two methods of accessing PCI memory space:
-
-          1) A direct mapped window from 0x48000000 to 0x4BFFFFFF (64MB).
-             To access PCI via this space, we simply ioremap() the BAR
-             into the kernel and we can use the standard read[bwl]/write[bwl]
-             macros. This is the preferred method due to speed but it
-             limits the system to just 64MB of PCI memory. This can be
-             problematic if using video cards and other memory-heavy devices.
-
-	  2) If > 64MB of memory space is required, the IXP4xx can be
-	     configured to use indirect registers to access the whole PCI
-	     memory space. This currently allows for up to 1 GB (0x10000000
-	     to 0x4FFFFFFF) of memory on the bus. The disadvantage of this
-	     is that every PCI access requires three local register accesses
-	     plus a spinlock, but in some cases the performance hit is
-	     acceptable. In addition, you cannot mmap() PCI devices in this
-	     case due to the indirect nature of the PCI window.
-
-	  By default, the direct method is used. Choose this option if you
-	  need to use the indirect method instead. If you don't know
-	  what you need, leave this option unselected.
-
-endmenu
-
-endif
+	  Support for Intel's IXP4XX (XScale) family of processors.
diff --git a/arch/arm/mach-ixp4xx/Makefile b/arch/arm/mach-ixp4xx/Makefile
index b241094c9649..3d1c9d854c7f 100644
--- a/arch/arm/mach-ixp4xx/Makefile
+++ b/arch/arm/mach-ixp4xx/Makefile
@@ -1,19 +1,2 @@
 # SPDX-License-Identifier: GPL-2.0
-#
-# Makefile for the linux kernel.
-#
-
-obj-pci-y	:=
-obj-pci-n	:=
-
-# Device tree platform
-obj-pci-$(CONFIG_MACH_IXP4XX_OF)	+= ixp4xx-of.o
-
-obj-pci-$(CONFIG_MACH_GATEWAY7001)	+= gateway7001-pci.o
-
-obj-y	+= common.o
-
-obj-$(CONFIG_MACH_GATEWAY7001)	+= gateway7001-setup.o
-obj-$(CONFIG_MACH_GORAMO_MLR)	+= goramo_mlr.o
-
-obj-$(CONFIG_PCI)		+= $(obj-pci-$(CONFIG_PCI)) common-pci.o
+obj-y	+= ixp4xx-of.o
diff --git a/arch/arm/mach-ixp4xx/Makefile.boot b/arch/arm/mach-ixp4xx/Makefile.boot
deleted file mode 100644
index 9b015bd1ef27..000000000000
--- a/arch/arm/mach-ixp4xx/Makefile.boot
+++ /dev/null
@@ -1,4 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0-only
-   zreladdr-y	+= 0x00008000
-params_phys-y	:= 0x00000100
-
diff --git a/arch/arm/mach-ixp4xx/common-pci.c b/arch/arm/mach-ixp4xx/common-pci.c
deleted file mode 100644
index 893c19c254e3..000000000000
--- a/arch/arm/mach-ixp4xx/common-pci.c
+++ /dev/null
@@ -1,451 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * arch/arm/mach-ixp4xx/common-pci.c 
- *
- * IXP4XX PCI routines for all platforms
- *
- * Maintainer: Deepak Saxena <dsaxena@plexity.net>
- *
- * Copyright (C) 2002 Intel Corporation.
- * Copyright (C) 2003 Greg Ungerer <gerg@snapgear.com>
- * Copyright (C) 2003-2004 MontaVista Software, Inc.
- */
-
-#include <linux/sched.h>
-#include <linux/kernel.h>
-#include <linux/pci.h>
-#include <linux/interrupt.h>
-#include <linux/mm.h>
-#include <linux/init.h>
-#include <linux/ioport.h>
-#include <linux/slab.h>
-#include <linux/delay.h>
-#include <linux/device.h>
-#include <linux/io.h>
-#include <linux/export.h>
-#include <asm/dma-mapping.h>
-
-#include <asm/cputype.h>
-#include <asm/irq.h>
-#include <linux/sizes.h>
-#include <asm/mach/pci.h>
-#include <mach/hardware.h>
-
-
-/*
- * IXP4xx PCI read function is dependent on whether we are 
- * running A0 or B0 (AppleGate) silicon.
- */
-int (*ixp4xx_pci_read)(u32 addr, u32 cmd, u32* data);
-
-/*
- * Base address for PCI register region
- */
-unsigned long ixp4xx_pci_reg_base = 0;
-
-/*
- * PCI cfg an I/O routines are done by programming a 
- * command/byte enable register, and then read/writing
- * the data from a data register. We need to ensure
- * these transactions are atomic or we will end up
- * with corrupt data on the bus or in a driver.
- */
-static DEFINE_RAW_SPINLOCK(ixp4xx_pci_lock);
-
-/*
- * Read from PCI config space
- */
-static void crp_read(u32 ad_cbe, u32 *data)
-{
-	unsigned long flags;
-	raw_spin_lock_irqsave(&ixp4xx_pci_lock, flags);
-	*PCI_CRP_AD_CBE = ad_cbe;
-	*data = *PCI_CRP_RDATA;
-	raw_spin_unlock_irqrestore(&ixp4xx_pci_lock, flags);
-}
-
-/*
- * Write to PCI config space
- */
-static void crp_write(u32 ad_cbe, u32 data)
-{ 
-	unsigned long flags;
-	raw_spin_lock_irqsave(&ixp4xx_pci_lock, flags);
-	*PCI_CRP_AD_CBE = CRP_AD_CBE_WRITE | ad_cbe;
-	*PCI_CRP_WDATA = data;
-	raw_spin_unlock_irqrestore(&ixp4xx_pci_lock, flags);
-}
-
-static inline int check_master_abort(void)
-{
-	/* check Master Abort bit after access */
-	unsigned long isr = *PCI_ISR;
-
-	if (isr & PCI_ISR_PFE) {
-		/* make sure the Master Abort bit is reset */    
-		*PCI_ISR = PCI_ISR_PFE;
-		pr_debug("%s failed\n", __func__);
-		return 1;
-	}
-
-	return 0;
-}
-
-int ixp4xx_pci_read_errata(u32 addr, u32 cmd, u32* data)
-{
-	unsigned long flags;
-	int retval = 0;
-	int i;
-
-	raw_spin_lock_irqsave(&ixp4xx_pci_lock, flags);
-
-	*PCI_NP_AD = addr;
-
-	/* 
-	 * PCI workaround  - only works if NP PCI space reads have 
-	 * no side effects!!! Read 8 times. last one will be good.
-	 */
-	for (i = 0; i < 8; i++) {
-		*PCI_NP_CBE = cmd;
-		*data = *PCI_NP_RDATA;
-		*data = *PCI_NP_RDATA;
-	}
-
-	if(check_master_abort())
-		retval = 1;
-
-	raw_spin_unlock_irqrestore(&ixp4xx_pci_lock, flags);
-	return retval;
-}
-
-int ixp4xx_pci_read_no_errata(u32 addr, u32 cmd, u32* data)
-{
-	unsigned long flags;
-	int retval = 0;
-
-	raw_spin_lock_irqsave(&ixp4xx_pci_lock, flags);
-
-	*PCI_NP_AD = addr;
-
-	/* set up and execute the read */    
-	*PCI_NP_CBE = cmd;
-
-	/* the result of the read is now in NP_RDATA */
-	*data = *PCI_NP_RDATA; 
-
-	if(check_master_abort())
-		retval = 1;
-
-	raw_spin_unlock_irqrestore(&ixp4xx_pci_lock, flags);
-	return retval;
-}
-
-int ixp4xx_pci_write(u32 addr, u32 cmd, u32 data)
-{    
-	unsigned long flags;
-	int retval = 0;
-
-	raw_spin_lock_irqsave(&ixp4xx_pci_lock, flags);
-
-	*PCI_NP_AD = addr;
-
-	/* set up the write */
-	*PCI_NP_CBE = cmd;
-
-	/* execute the write by writing to NP_WDATA */
-	*PCI_NP_WDATA = data;
-
-	if(check_master_abort())
-		retval = 1;
-
-	raw_spin_unlock_irqrestore(&ixp4xx_pci_lock, flags);
-	return retval;
-}
-
-static u32 ixp4xx_config_addr(u8 bus_num, u16 devfn, int where)
-{
-	u32 addr;
-	if (!bus_num) {
-		/* type 0 */
-		addr = BIT(32-PCI_SLOT(devfn)) | ((PCI_FUNC(devfn)) << 8) | 
-		    (where & ~3);	
-	} else {
-		/* type 1 */
-		addr = (bus_num << 16) | ((PCI_SLOT(devfn)) << 11) | 
-			((PCI_FUNC(devfn)) << 8) | (where & ~3) | 1;
-	}
-	return addr;
-}
-
-/*
- * Mask table, bits to mask for quantity of size 1, 2 or 4 bytes.
- * 0 and 3 are not valid indexes...
- */
-static u32 bytemask[] = {
-	/*0*/	0,
-	/*1*/	0xff,
-	/*2*/	0xffff,
-	/*3*/	0,
-	/*4*/	0xffffffff,
-};
-
-static u32 local_byte_lane_enable_bits(u32 n, int size)
-{
-	if (size == 1)
-		return (0xf & ~BIT(n)) << CRP_AD_CBE_BESL;
-	if (size == 2)
-		return (0xf & ~(BIT(n) | BIT(n+1))) << CRP_AD_CBE_BESL;
-	if (size == 4)
-		return 0;
-	return 0xffffffff;
-}
-
-static int local_read_config(int where, int size, u32 *value)
-{ 
-	u32 n, data;
-	pr_debug("local_read_config from %d size %d\n", where, size);
-	n = where % 4;
-	crp_read(where & ~3, &data);
-	*value = (data >> (8*n)) & bytemask[size];
-	pr_debug("local_read_config read %#x\n", *value);
-	return PCIBIOS_SUCCESSFUL;
-}
-
-static int local_write_config(int where, int size, u32 value)
-{
-	u32 n, byte_enables, data;
-	pr_debug("local_write_config %#x to %d size %d\n", value, where, size);
-	n = where % 4;
-	byte_enables = local_byte_lane_enable_bits(n, size);
-	if (byte_enables == 0xffffffff)
-		return PCIBIOS_BAD_REGISTER_NUMBER;
-	data = value << (8*n);
-	crp_write((where & ~3) | byte_enables, data);
-	return PCIBIOS_SUCCESSFUL;
-}
-
-static u32 byte_lane_enable_bits(u32 n, int size)
-{
-	if (size == 1)
-		return (0xf & ~BIT(n)) << 4;
-	if (size == 2)
-		return (0xf & ~(BIT(n) | BIT(n+1))) << 4;
-	if (size == 4)
-		return 0;
-	return 0xffffffff;
-}
-
-static int ixp4xx_pci_read_config(struct pci_bus *bus, unsigned int devfn, int where, int size, u32 *value)
-{
-	u32 n, byte_enables, addr, data;
-	u8 bus_num = bus->number;
-
-	pr_debug("read_config from %d size %d dev %d:%d:%d\n", where, size,
-		bus_num, PCI_SLOT(devfn), PCI_FUNC(devfn));
-
-	*value = 0xffffffff;
-	n = where % 4;
-	byte_enables = byte_lane_enable_bits(n, size);
-	if (byte_enables == 0xffffffff)
-		return PCIBIOS_BAD_REGISTER_NUMBER;
-
-	addr = ixp4xx_config_addr(bus_num, devfn, where);
-	if (ixp4xx_pci_read(addr, byte_enables | NP_CMD_CONFIGREAD, &data))
-		return PCIBIOS_DEVICE_NOT_FOUND;
-
-	*value = (data >> (8*n)) & bytemask[size];
-	pr_debug("read_config_byte read %#x\n", *value);
-	return PCIBIOS_SUCCESSFUL;
-}
-
-static int ixp4xx_pci_write_config(struct pci_bus *bus,  unsigned int devfn, int where, int size, u32 value)
-{
-	u32 n, byte_enables, addr, data;
-	u8 bus_num = bus->number;
-
-	pr_debug("write_config_byte %#x to %d size %d dev %d:%d:%d\n", value, where,
-		size, bus_num, PCI_SLOT(devfn), PCI_FUNC(devfn));
-
-	n = where % 4;
-	byte_enables = byte_lane_enable_bits(n, size);
-	if (byte_enables == 0xffffffff)
-		return PCIBIOS_BAD_REGISTER_NUMBER;
-
-	addr = ixp4xx_config_addr(bus_num, devfn, where);
-	data = value << (8*n);
-	if (ixp4xx_pci_write(addr, byte_enables | NP_CMD_CONFIGWRITE, data))
-		return PCIBIOS_DEVICE_NOT_FOUND;
-
-	return PCIBIOS_SUCCESSFUL;
-}
-
-struct pci_ops ixp4xx_ops = {
-	.read =  ixp4xx_pci_read_config,
-	.write = ixp4xx_pci_write_config,
-};
-
-/*
- * PCI abort handler
- */
-static int abort_handler(unsigned long addr, unsigned int fsr, struct pt_regs *regs)
-{
-	u32 isr, status;
-
-	isr = *PCI_ISR;
-	local_read_config(PCI_STATUS, 2, &status);
-	pr_debug("PCI: abort_handler addr = %#lx, isr = %#x, "
-		"status = %#x\n", addr, isr, status);
-
-	/* make sure the Master Abort bit is reset */    
-	*PCI_ISR = PCI_ISR_PFE;
-	status |= PCI_STATUS_REC_MASTER_ABORT;
-	local_write_config(PCI_STATUS, 2, status);
-
-	/*
-	 * If it was an imprecise abort, then we need to correct the
-	 * return address to be _after_ the instruction.
-	 */
-	if (fsr & (1 << 10))
-		regs->ARM_pc += 4;
-
-	return 0;
-}
-
-void __init ixp4xx_pci_preinit(void)
-{
-	unsigned long cpuid = read_cpuid_id();
-
-#ifdef CONFIG_IXP4XX_INDIRECT_PCI
-	pcibios_min_mem = 0x10000000; /* 1 GB of indirect PCI MMIO space */
-#else
-	pcibios_min_mem = 0x48000000; /* 64 MB of PCI MMIO space */
-#endif
-	/*
-	 * Determine which PCI read method to use.
-	 * Rev 0 IXP425 requires workaround.
-	 */
-	if (!(cpuid & 0xf) && cpu_is_ixp42x()) {
-		printk("PCI: IXP42x A0 silicon detected - "
-			"PCI Non-Prefetch Workaround Enabled\n");
-		ixp4xx_pci_read = ixp4xx_pci_read_errata;
-	} else
-		ixp4xx_pci_read = ixp4xx_pci_read_no_errata;
-
-
-	/* hook in our fault handler for PCI errors */
-	hook_fault_code(16+6, abort_handler, SIGBUS, 0,
-			"imprecise external abort");
-
-	pr_debug("setup PCI-AHB(inbound) and AHB-PCI(outbound) address mappings\n");
-
-	/*
-	 * We use identity AHB->PCI address translation
-	 * in the 0x48000000 to 0x4bffffff address space
-	 */
-	*PCI_PCIMEMBASE = 0x48494A4B;
-
-	/*
-	 * We also use identity PCI->AHB address translation
-	 * in 4 16MB BARs that begin at the physical memory start
-	 */
-	*PCI_AHBMEMBASE = (PHYS_OFFSET & 0xFF000000) +
-		((PHYS_OFFSET & 0xFF000000) >> 8) +
-		((PHYS_OFFSET & 0xFF000000) >> 16) +
-		((PHYS_OFFSET & 0xFF000000) >> 24) +
-		0x00010203;
-
-	if (*PCI_CSR & PCI_CSR_HOST) {
-		printk("PCI: IXP4xx is host\n");
-
-		pr_debug("setup BARs in controller\n");
-
-		/*
-		 * We configure the PCI inbound memory windows to be
-		 * 1:1 mapped to SDRAM
-		 */
-		local_write_config(PCI_BASE_ADDRESS_0, 4, PHYS_OFFSET);
-		local_write_config(PCI_BASE_ADDRESS_1, 4, PHYS_OFFSET + SZ_16M);
-		local_write_config(PCI_BASE_ADDRESS_2, 4, PHYS_OFFSET + SZ_32M);
-		local_write_config(PCI_BASE_ADDRESS_3, 4,
-					PHYS_OFFSET + SZ_32M + SZ_16M);
-
-		/*
-		 * Enable CSR window at 64 MiB to allow PCI masters
-		 * to continue prefetching past 64 MiB boundary.
-		 */
-		local_write_config(PCI_BASE_ADDRESS_4, 4, PHYS_OFFSET + SZ_64M);
-
-		/*
-		 * Enable the IO window to be way up high, at 0xfffffc00
-		 */
-		local_write_config(PCI_BASE_ADDRESS_5, 4, 0xfffffc01);
-		local_write_config(0x40, 4, 0x000080FF); /* No TRDY time limit */
-	} else {
-		printk("PCI: IXP4xx is target - No bus scan performed\n");
-	}
-
-	printk("PCI: IXP4xx Using %s access for memory space\n",
-#ifndef CONFIG_IXP4XX_INDIRECT_PCI
-			"direct"
-#else
-			"indirect"
-#endif
-		);
-
-	pr_debug("clear error bits in ISR\n");
-	*PCI_ISR = PCI_ISR_PSE | PCI_ISR_PFE | PCI_ISR_PPE | PCI_ISR_AHBE;
-
-	/*
-	 * Set Initialize Complete in PCI Control Register: allow IXP4XX to
-	 * respond to PCI configuration cycles. Specify that the AHB bus is
-	 * operating in big endian mode. Set up byte lane swapping between 
-	 * little-endian PCI and the big-endian AHB bus 
-	 */
-#ifdef __ARMEB__
-	*PCI_CSR = PCI_CSR_IC | PCI_CSR_ABE | PCI_CSR_PDS | PCI_CSR_ADS;
-#else
-	*PCI_CSR = PCI_CSR_IC | PCI_CSR_ABE;
-#endif
-
-	pr_debug("DONE\n");
-}
-
-int ixp4xx_setup(int nr, struct pci_sys_data *sys)
-{
-	struct resource *res;
-
-	if (nr >= 1)
-		return 0;
-
-	res = kcalloc(2, sizeof(*res), GFP_KERNEL);
-	if (res == NULL) {
-		/* 
-		 * If we're out of memory this early, something is wrong,
-		 * so we might as well catch it here.
-		 */
-		panic("PCI: unable to allocate resources?\n");
-	}
-
-	local_write_config(PCI_COMMAND, 2, PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY);
-
-	res[0].name = "PCI I/O Space";
-	res[0].start = 0x00000000;
-	res[0].end = 0x0000ffff;
-	res[0].flags = IORESOURCE_IO;
-
-	res[1].name = "PCI Memory Space";
-	res[1].start = PCIBIOS_MIN_MEM;
-	res[1].end = PCIBIOS_MAX_MEM;
-	res[1].flags = IORESOURCE_MEM;
-
-	request_resource(&ioport_resource, &res[0]);
-	request_resource(&iomem_resource, &res[1]);
-
-	pci_add_resource_offset(&sys->resources, &res[0], sys->io_offset);
-	pci_add_resource_offset(&sys->resources, &res[1], sys->mem_offset);
-
-	return 1;
-}
-
-EXPORT_SYMBOL(ixp4xx_pci_read);
-EXPORT_SYMBOL(ixp4xx_pci_write);
diff --git a/arch/arm/mach-ixp4xx/common.c b/arch/arm/mach-ixp4xx/common.c
deleted file mode 100644
index cdc720f54daa..000000000000
--- a/arch/arm/mach-ixp4xx/common.c
+++ /dev/null
@@ -1,448 +0,0 @@
-/*
- * arch/arm/mach-ixp4xx/common.c
- *
- * Generic code shared across all IXP4XX platforms
- *
- * Maintainer: Deepak Saxena <dsaxena@plexity.net>
- *
- * Copyright 2002 (c) Intel Corporation
- * Copyright 2003-2004 (c) MontaVista, Software, Inc. 
- * 
- * This file is licensed under  the terms of the GNU General Public 
- * License version 2. This program is licensed "as is" without any 
- * warranty of any kind, whether express or implied.
- */
-
-#include <linux/kernel.h>
-#include <linux/mm.h>
-#include <linux/init.h>
-#include <linux/serial.h>
-#include <linux/tty.h>
-#include <linux/platform_device.h>
-#include <linux/serial_core.h>
-#include <linux/interrupt.h>
-#include <linux/bitops.h>
-#include <linux/io.h>
-#include <linux/export.h>
-#include <linux/cpu.h>
-#include <linux/pci.h>
-#include <linux/sched_clock.h>
-#include <linux/soc/ixp4xx/cpu.h>
-#include <linux/irqchip/irq-ixp4xx.h>
-#include <linux/platform_data/timer-ixp4xx.h>
-#include <linux/dma-map-ops.h>
-#include <mach/udc.h>
-#include <mach/hardware.h>
-#include <linux/uaccess.h>
-#include <asm/page.h>
-#include <asm/exception.h>
-#include <asm/irq.h>
-#include <asm/system_misc.h>
-#include <asm/mach/map.h>
-#include <asm/mach/irq.h>
-#include <asm/mach/time.h>
-
-#include "irqs.h"
-
-u32 ixp4xx_read_feature_bits(void)
-{
-	u32 val = ~__raw_readl(IXP4XX_EXP_CFG2);
-
-	if (cpu_is_ixp42x_rev_a0())
-		return IXP42X_FEATURE_MASK & ~(IXP4XX_FEATURE_RCOMP |
-					       IXP4XX_FEATURE_AES);
-	if (cpu_is_ixp42x())
-		return val & IXP42X_FEATURE_MASK;
-	if (cpu_is_ixp43x())
-		return val & IXP43X_FEATURE_MASK;
-	return val & IXP46X_FEATURE_MASK;
-}
-EXPORT_SYMBOL(ixp4xx_read_feature_bits);
-
-void ixp4xx_write_feature_bits(u32 value)
-{
-	__raw_writel(~value, IXP4XX_EXP_CFG2);
-}
-EXPORT_SYMBOL(ixp4xx_write_feature_bits);
-
-#define IXP4XX_TIMER_FREQ 66666000
-
-/*************************************************************************
- * IXP4xx chipset I/O mapping
- *************************************************************************/
-static struct map_desc ixp4xx_io_desc[] __initdata = {
-	{	/* UART, Interrupt ctrl, GPIO, timers, NPEs, MACs, USB .... */
-		.virtual	= (unsigned long)IXP4XX_PERIPHERAL_BASE_VIRT,
-		.pfn		= __phys_to_pfn(IXP4XX_PERIPHERAL_BASE_PHYS),
-		.length		= IXP4XX_PERIPHERAL_REGION_SIZE,
-		.type		= MT_DEVICE
-	}, {	/* Expansion Bus Config Registers */
-		.virtual	= (unsigned long)IXP4XX_EXP_CFG_BASE_VIRT,
-		.pfn		= __phys_to_pfn(IXP4XX_EXP_CFG_BASE_PHYS),
-		.length		= IXP4XX_EXP_CFG_REGION_SIZE,
-		.type		= MT_DEVICE
-	}, {	/* PCI Registers */
-		.virtual	= (unsigned long)IXP4XX_PCI_CFG_BASE_VIRT,
-		.pfn		= __phys_to_pfn(IXP4XX_PCI_CFG_BASE_PHYS),
-		.length		= IXP4XX_PCI_CFG_REGION_SIZE,
-		.type		= MT_DEVICE
-	},
-};
-
-void __init ixp4xx_map_io(void)
-{
-  	iotable_init(ixp4xx_io_desc, ARRAY_SIZE(ixp4xx_io_desc));
-}
-
-void __init ixp4xx_init_irq(void)
-{
-	/*
-	 * ixp4xx does not implement the XScale PWRMODE register
-	 * so it must not call cpu_do_idle().
-	 */
-	cpu_idle_poll_ctrl(true);
-
-	ixp4xx_irq_init(IXP4XX_INTC_BASE_PHYS,
-			(cpu_is_ixp46x() || cpu_is_ixp43x()));
-}
-
-void __init ixp4xx_timer_init(void)
-{
-	return ixp4xx_timer_setup(IXP4XX_TIMER_BASE_PHYS,
-				  IRQ_IXP4XX_TIMER1,
-				  IXP4XX_TIMER_FREQ);
-}
-
-static struct pxa2xx_udc_mach_info ixp4xx_udc_info;
-
-void __init ixp4xx_set_udc_info(struct pxa2xx_udc_mach_info *info)
-{
-	memcpy(&ixp4xx_udc_info, info, sizeof *info);
-}
-
-static struct resource ixp4xx_udc_resources[] = {
-	[0] = {
-		.start  = 0xc800b000,
-		.end    = 0xc800bfff,
-		.flags  = IORESOURCE_MEM,
-	},
-	[1] = {
-		.start  = IRQ_IXP4XX_USB,
-		.end    = IRQ_IXP4XX_USB,
-		.flags  = IORESOURCE_IRQ,
-	},
-};
-
-static struct resource ixp4xx_gpio_resource[] = {
-	{
-		.start = IXP4XX_GPIO_BASE_PHYS,
-		.end = IXP4XX_GPIO_BASE_PHYS + 0xfff,
-		.flags = IORESOURCE_MEM,
-	},
-};
-
-static struct platform_device ixp4xx_gpio_device = {
-	.name           = "ixp4xx-gpio",
-	.id             = -1,
-	.dev = {
-		.coherent_dma_mask      = DMA_BIT_MASK(32),
-	},
-	.resource = ixp4xx_gpio_resource,
-	.num_resources  = ARRAY_SIZE(ixp4xx_gpio_resource),
-};
-
-/*
- * USB device controller. The IXP4xx uses the same controller as PXA25X,
- * so we just use the same device.
- */
-static struct platform_device ixp4xx_udc_device = {
-	.name           = "pxa25x-udc",
-	.id             = -1,
-	.num_resources  = 2,
-	.resource       = ixp4xx_udc_resources,
-	.dev            = {
-		.platform_data = &ixp4xx_udc_info,
-	},
-};
-
-static struct resource ixp4xx_npe_resources[] = {
-	{
-		.start = IXP4XX_NPEA_BASE_PHYS,
-		.end = IXP4XX_NPEA_BASE_PHYS + 0xfff,
-		.flags = IORESOURCE_MEM,
-	},
-	{
-		.start = IXP4XX_NPEB_BASE_PHYS,
-		.end = IXP4XX_NPEB_BASE_PHYS + 0xfff,
-		.flags = IORESOURCE_MEM,
-	},
-	{
-		.start = IXP4XX_NPEC_BASE_PHYS,
-		.end = IXP4XX_NPEC_BASE_PHYS + 0xfff,
-		.flags = IORESOURCE_MEM,
-	},
-
-};
-
-static struct platform_device ixp4xx_npe_device = {
-	.name           = "ixp4xx-npe",
-	.id             = -1,
-	.num_resources  = ARRAY_SIZE(ixp4xx_npe_resources),
-	.resource       = ixp4xx_npe_resources,
-};
-
-static struct resource ixp4xx_qmgr_resources[] = {
-	{
-		.start = IXP4XX_QMGR_BASE_PHYS,
-		.end = IXP4XX_QMGR_BASE_PHYS + 0x3fff,
-		.flags = IORESOURCE_MEM,
-	},
-	{
-		.start = IRQ_IXP4XX_QM1,
-		.end = IRQ_IXP4XX_QM1,
-		.flags = IORESOURCE_IRQ,
-	},
-	{
-		.start = IRQ_IXP4XX_QM2,
-		.end = IRQ_IXP4XX_QM2,
-		.flags = IORESOURCE_IRQ,
-	},
-};
-
-static struct platform_device ixp4xx_qmgr_device = {
-	.name           = "ixp4xx-qmgr",
-	.id             = -1,
-	.num_resources  = ARRAY_SIZE(ixp4xx_qmgr_resources),
-	.resource       = ixp4xx_qmgr_resources,
-};
-
-static struct platform_device *ixp4xx_devices[] __initdata = {
-	&ixp4xx_npe_device,
-	&ixp4xx_qmgr_device,
-	&ixp4xx_gpio_device,
-	&ixp4xx_udc_device,
-};
-
-static struct resource ixp46x_i2c_resources[] = {
-	[0] = {
-		.start 	= 0xc8011000,
-		.end	= 0xc801101c,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start 	= IRQ_IXP4XX_I2C,
-		.end	= IRQ_IXP4XX_I2C,
-		.flags	= IORESOURCE_IRQ
-	}
-};
-
-/* A single 32-bit register on IXP46x */
-#define IXP4XX_HWRANDOM_BASE_PHYS	0x70002100
-
-static struct resource ixp46x_hwrandom_resource[] = {
-	{
-		.start = IXP4XX_HWRANDOM_BASE_PHYS,
-		.end = IXP4XX_HWRANDOM_BASE_PHYS + 0x3,
-		.flags = IORESOURCE_MEM,
-	},
-};
-
-static struct platform_device ixp46x_hwrandom_device = {
-	.name           = "ixp4xx-hwrandom",
-	.id             = -1,
-	.dev = {
-		.coherent_dma_mask      = DMA_BIT_MASK(32),
-	},
-	.resource = ixp46x_hwrandom_resource,
-	.num_resources  = ARRAY_SIZE(ixp46x_hwrandom_resource),
-};
-
-/*
- * I2C controller. The IXP46x uses the same block as the IOP3xx, so
- * we just use the same device name.
- */
-static struct platform_device ixp46x_i2c_controller = {
-	.name		= "IOP3xx-I2C",
-	.id		= 0,
-	.num_resources	= 2,
-	.resource	= ixp46x_i2c_resources
-};
-
-static struct resource ixp46x_ptp_resources[] = {
-	DEFINE_RES_MEM(IXP4XX_TIMESYNC_BASE_PHYS, SZ_4K),
-	DEFINE_RES_IRQ_NAMED(IRQ_IXP4XX_GPIO8, "master"),
-	DEFINE_RES_IRQ_NAMED(IRQ_IXP4XX_GPIO7, "slave"),
-};
-
-static struct platform_device ixp46x_ptp = {
-	.name		= "ptp-ixp46x",
-	.id		= -1,
-	.resource	= ixp46x_ptp_resources,
-	.num_resources	= ARRAY_SIZE(ixp46x_ptp_resources),
-};
-
-static struct platform_device *ixp46x_devices[] __initdata = {
-	&ixp46x_hwrandom_device,
-	&ixp46x_i2c_controller,
-	&ixp46x_ptp,
-};
-
-unsigned long ixp4xx_exp_bus_size;
-EXPORT_SYMBOL(ixp4xx_exp_bus_size);
-
-static struct platform_device_info ixp_dev_info __initdata = {
-	.name		= "ixp4xx_crypto",
-	.id		= 0,
-	.dma_mask	= DMA_BIT_MASK(32),
-};
-
-static int __init ixp_crypto_register(void)
-{
-	struct platform_device *pdev;
-
-	if (!(~(*IXP4XX_EXP_CFG2) & (IXP4XX_FEATURE_HASH |
-				IXP4XX_FEATURE_AES | IXP4XX_FEATURE_DES))) {
-		printk(KERN_ERR "ixp_crypto: No HW crypto available\n");
-		return -ENODEV;
-	}
-
-	pdev = platform_device_register_full(&ixp_dev_info);
-	if (IS_ERR(pdev))
-		return PTR_ERR(pdev);
-
-	return 0;
-}
-
-void __init ixp4xx_sys_init(void)
-{
-	ixp4xx_exp_bus_size = SZ_16M;
-
-	platform_add_devices(ixp4xx_devices, ARRAY_SIZE(ixp4xx_devices));
-
-	if (IS_ENABLED(CONFIG_CRYPTO_DEV_IXP4XX))
-		ixp_crypto_register();
-
-	if (cpu_is_ixp46x()) {
-		int region;
-
-		platform_add_devices(ixp46x_devices,
-				ARRAY_SIZE(ixp46x_devices));
-
-		for (region = 0; region < 7; region++) {
-			if((*(IXP4XX_EXP_REG(0x4 * region)) & 0x200)) {
-				ixp4xx_exp_bus_size = SZ_32M;
-				break;
-			}
-		}
-	}
-
-	printk("IXP4xx: Using %luMiB expansion bus window size\n",
-			ixp4xx_exp_bus_size >> 20);
-}
-
-unsigned long ixp4xx_timer_freq = IXP4XX_TIMER_FREQ;
-EXPORT_SYMBOL(ixp4xx_timer_freq);
-
-void ixp4xx_restart(enum reboot_mode mode, const char *cmd)
-{
-	if (mode == REBOOT_SOFT) {
-		/* Jump into ROM at address 0 */
-		soft_restart(0);
-	} else {
-		/* Use on-chip reset capability */
-
-		/* set the "key" register to enable access to
-		 * "timer" and "enable" registers
-		 */
-		*IXP4XX_OSWK = IXP4XX_WDT_KEY;
-
-		/* write 0 to the timer register for an immediate reset */
-		*IXP4XX_OSWT = 0;
-
-		*IXP4XX_OSWE = IXP4XX_WDT_RESET_ENABLE | IXP4XX_WDT_COUNT_ENABLE;
-	}
-}
-
-#ifdef CONFIG_PCI
-static int ixp4xx_needs_bounce(struct device *dev, dma_addr_t dma_addr, size_t size)
-{
-	return (dma_addr + size) > SZ_64M;
-}
-
-static int ixp4xx_platform_notify_remove(struct device *dev)
-{
-	if (dev_is_pci(dev))
-		dmabounce_unregister_dev(dev);
-
-	return 0;
-}
-#endif
-
-/*
- * Setup DMA mask to 64MB on PCI devices and 4 GB on all other things.
- */
-static int ixp4xx_platform_notify(struct device *dev)
-{
-	dev->dma_mask = &dev->coherent_dma_mask;
-
-#ifdef CONFIG_PCI
-	if (dev_is_pci(dev)) {
-		dev->coherent_dma_mask = DMA_BIT_MASK(28); /* 64 MB */
-		dmabounce_register_dev(dev, 2048, 4096, ixp4xx_needs_bounce);
-		return 0;
-	}
-#endif
-
-	dev->coherent_dma_mask = DMA_BIT_MASK(32);
-	return 0;
-}
-
-int dma_set_coherent_mask(struct device *dev, u64 mask)
-{
-	if (dev_is_pci(dev))
-		mask &= DMA_BIT_MASK(28); /* 64 MB */
-
-	if ((mask & DMA_BIT_MASK(28)) == DMA_BIT_MASK(28)) {
-		dev->coherent_dma_mask = mask;
-		return 0;
-	}
-
-	return -EIO;		/* device wanted sub-64MB mask */
-}
-EXPORT_SYMBOL(dma_set_coherent_mask);
-
-#ifdef CONFIG_IXP4XX_INDIRECT_PCI
-/*
- * In the case of using indirect PCI, we simply return the actual PCI
- * address and our read/write implementation use that to drive the
- * access registers. If something outside of PCI is ioremap'd, we
- * fallback to the default.
- */
-
-static void __iomem *ixp4xx_ioremap_caller(phys_addr_t addr, size_t size,
-					   unsigned int mtype, void *caller)
-{
-	if (!is_pci_memory(addr))
-		return __arm_ioremap_caller(addr, size, mtype, caller);
-
-	return (void __iomem *)addr;
-}
-
-static void ixp4xx_iounmap(volatile void __iomem *addr)
-{
-	if (!is_pci_memory((__force u32)addr))
-		__iounmap(addr);
-}
-#endif
-
-void __init ixp4xx_init_early(void)
-{
-	platform_notify = ixp4xx_platform_notify;
-#ifdef CONFIG_PCI
-	platform_notify_remove = ixp4xx_platform_notify_remove;
-#endif
-#ifdef CONFIG_IXP4XX_INDIRECT_PCI
-	arch_ioremap_caller = ixp4xx_ioremap_caller;
-	arch_iounmap = ixp4xx_iounmap;
-#endif
-}
diff --git a/arch/arm/mach-ixp4xx/gateway7001-pci.c b/arch/arm/mach-ixp4xx/gateway7001-pci.c
deleted file mode 100644
index 3c3ee9dad6d8..000000000000
--- a/arch/arm/mach-ixp4xx/gateway7001-pci.c
+++ /dev/null
@@ -1,61 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * arch/arch/mach-ixp4xx/gateway7001-pci.c
- *
- * PCI setup routines for Gateway 7001
- *
- * Copyright (C) 2007 Imre Kaloz <kaloz@openwrt.org>
- *
- * based on coyote-pci.c:
- *	Copyright (C) 2002 Jungo Software Technologies.
- *	Copyright (C) 2003 MontaVista Softwrae, Inc.
- *
- * Maintainer: Imre Kaloz <kaloz@openwrt.org>
- */
-
-#include <linux/kernel.h>
-#include <linux/pci.h>
-#include <linux/init.h>
-#include <linux/irq.h>
-
-#include <asm/mach-types.h>
-#include <mach/hardware.h>
-
-#include <asm/mach/pci.h>
-
-#include "irqs.h"
-
-void __init gateway7001_pci_preinit(void)
-{
-	irq_set_irq_type(IRQ_IXP4XX_GPIO10, IRQ_TYPE_LEVEL_LOW);
-	irq_set_irq_type(IRQ_IXP4XX_GPIO11, IRQ_TYPE_LEVEL_LOW);
-
-	ixp4xx_pci_preinit();
-}
-
-static int __init gateway7001_map_irq(const struct pci_dev *dev, u8 slot,
-	u8 pin)
-{
-	if (slot == 1)
-		return IRQ_IXP4XX_GPIO11;
-	else if (slot == 2)
-		return IRQ_IXP4XX_GPIO10;
-	else return -1;
-}
-
-struct hw_pci gateway7001_pci __initdata = {
-	.nr_controllers = 1,
-	.ops		= &ixp4xx_ops,
-	.preinit =        gateway7001_pci_preinit,
-	.setup =          ixp4xx_setup,
-	.map_irq =        gateway7001_map_irq,
-};
-
-int __init gateway7001_pci_init(void)
-{
-	if (machine_is_gateway7001())
-		pci_common_init(&gateway7001_pci);
-	return 0;
-}
-
-subsys_initcall(gateway7001_pci_init);
diff --git a/arch/arm/mach-ixp4xx/gateway7001-setup.c b/arch/arm/mach-ixp4xx/gateway7001-setup.c
deleted file mode 100644
index 678e7dfff0e5..000000000000
--- a/arch/arm/mach-ixp4xx/gateway7001-setup.c
+++ /dev/null
@@ -1,113 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * arch/arm/mach-ixp4xx/gateway7001-setup.c
- *
- * Board setup for the Gateway 7001 board
- *
- * Copyright (C) 2007 Imre Kaloz <kaloz@openwrt.org>
- *
- * based on coyote-setup.c:
- *      Copyright (C) 2003-2005 MontaVista Software, Inc.
- *
- * Author: Imre Kaloz <Kaloz@openwrt.org>
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/device.h>
-#include <linux/serial.h>
-#include <linux/tty.h>
-#include <linux/serial_8250.h>
-
-#include <asm/types.h>
-#include <asm/setup.h>
-#include <asm/memory.h>
-#include <mach/hardware.h>
-#include <asm/irq.h>
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/flash.h>
-
-#include "irqs.h"
-
-static struct flash_platform_data gateway7001_flash_data = {
-	.map_name	= "cfi_probe",
-	.width		= 2,
-};
-
-static struct resource gateway7001_flash_resource = {
-	.flags		= IORESOURCE_MEM,
-};
-
-static struct platform_device gateway7001_flash = {
-	.name		= "IXP4XX-Flash",
-	.id		= 0,
-	.dev		= {
-		.platform_data = &gateway7001_flash_data,
-	},
-	.num_resources	= 1,
-	.resource	= &gateway7001_flash_resource,
-};
-
-static struct resource gateway7001_uart_resource = {
-	.start	= IXP4XX_UART2_BASE_PHYS,
-	.end	= IXP4XX_UART2_BASE_PHYS + 0x0fff,
-	.flags	= IORESOURCE_MEM,
-};
-
-static struct plat_serial8250_port gateway7001_uart_data[] = {
-	{
-		.mapbase	= IXP4XX_UART2_BASE_PHYS,
-		.membase	= (char *)IXP4XX_UART2_BASE_VIRT + REG_OFFSET,
-		.irq		= IRQ_IXP4XX_UART2,
-		.flags		= UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
-		.iotype		= UPIO_MEM,
-		.regshift	= 2,
-		.uartclk	= IXP4XX_UART_XTAL,
-	},
-	{ },
-};
-
-static struct platform_device gateway7001_uart = {
-	.name		= "serial8250",
-	.id		= PLAT8250_DEV_PLATFORM,
-	.dev			= {
-		.platform_data	= gateway7001_uart_data,
-	},
-	.num_resources	= 1,
-	.resource	= &gateway7001_uart_resource,
-};
-
-static struct platform_device *gateway7001_devices[] __initdata = {
-	&gateway7001_flash,
-	&gateway7001_uart
-};
-
-static void __init gateway7001_init(void)
-{
-	ixp4xx_sys_init();
-
-	gateway7001_flash_resource.start = IXP4XX_EXP_BUS_BASE(0);
-	gateway7001_flash_resource.end = IXP4XX_EXP_BUS_BASE(0) + SZ_32M - 1;
-
-	*IXP4XX_EXP_CS0 |= IXP4XX_FLASH_WRITABLE;
-	*IXP4XX_EXP_CS1 = *IXP4XX_EXP_CS0;
-
-	platform_add_devices(gateway7001_devices, ARRAY_SIZE(gateway7001_devices));
-}
-
-#ifdef CONFIG_MACH_GATEWAY7001
-MACHINE_START(GATEWAY7001, "Gateway 7001 AP")
-	/* Maintainer: Imre Kaloz <kaloz@openwrt.org> */
-	.map_io		= ixp4xx_map_io,
-	.init_early	= ixp4xx_init_early,
-	.init_irq	= ixp4xx_init_irq,
-	.init_time	= ixp4xx_timer_init,
-	.atag_offset	= 0x100,
-	.init_machine	= gateway7001_init,
-#if defined(CONFIG_PCI)
-	.dma_zone_size	= SZ_64M,
-#endif
-	.restart	= ixp4xx_restart,
-MACHINE_END
-#endif
diff --git a/arch/arm/mach-ixp4xx/goramo_mlr.c b/arch/arm/mach-ixp4xx/goramo_mlr.c
deleted file mode 100644
index 07b50dfcc489..000000000000
--- a/arch/arm/mach-ixp4xx/goramo_mlr.c
+++ /dev/null
@@ -1,532 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Goramo MultiLink router platform code
- * Copyright (C) 2006-2009 Krzysztof Halasa <khc@pm.waw.pl>
- */
-
-#include <linux/delay.h>
-#include <linux/gpio.h>
-#include <linux/hdlc.h>
-#include <linux/io.h>
-#include <linux/irq.h>
-#include <linux/kernel.h>
-#include <linux/pci.h>
-#include <linux/platform_data/wan_ixp4xx_hss.h>
-#include <linux/serial_8250.h>
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/flash.h>
-#include <asm/mach/pci.h>
-#include <asm/system_info.h>
-
-#include "irqs.h"
-
-#define SLOT_ETHA		0x0B	/* IDSEL = AD21 */
-#define SLOT_ETHB		0x0C	/* IDSEL = AD20 */
-#define SLOT_MPCI		0x0D	/* IDSEL = AD19 */
-#define SLOT_NEC		0x0E	/* IDSEL = AD18 */
-
-/* GPIO lines */
-#define GPIO_SCL		0
-#define GPIO_SDA		1
-#define GPIO_STR		2
-#define GPIO_IRQ_NEC		3
-#define GPIO_IRQ_ETHA		4
-#define GPIO_IRQ_ETHB		5
-#define GPIO_HSS0_DCD_N		6
-#define GPIO_HSS1_DCD_N		7
-#define GPIO_UART0_DCD		8
-#define GPIO_UART1_DCD		9
-#define GPIO_HSS0_CTS_N		10
-#define GPIO_HSS1_CTS_N		11
-#define GPIO_IRQ_MPCI		12
-#define GPIO_HSS1_RTS_N		13
-#define GPIO_HSS0_RTS_N		14
-/* GPIO15 is not connected */
-
-/* Control outputs from 74HC4094 */
-#define CONTROL_HSS0_CLK_INT	0
-#define CONTROL_HSS1_CLK_INT	1
-#define CONTROL_HSS0_DTR_N	2
-#define CONTROL_HSS1_DTR_N	3
-#define CONTROL_EXT		4
-#define CONTROL_AUTO_RESET	5
-#define CONTROL_PCI_RESET_N	6
-#define CONTROL_EEPROM_WC_N	7
-
-/* offsets from start of flash ROM = 0x50000000 */
-#define CFG_ETH0_ADDRESS	0x40 /* 6 bytes */
-#define CFG_ETH1_ADDRESS	0x46 /* 6 bytes */
-#define CFG_REV			0x4C /* u32 */
-#define CFG_SDRAM_SIZE		0x50 /* u32 */
-#define CFG_SDRAM_CONF		0x54 /* u32 */
-#define CFG_SDRAM_MODE		0x58 /* u32 */
-#define CFG_SDRAM_REFRESH	0x5C /* u32 */
-
-#define CFG_HW_BITS		0x60 /* u32 */
-#define  CFG_HW_USB_PORTS	0x00000007 /* 0 = no NEC chip, 1-5 = ports # */
-#define  CFG_HW_HAS_PCI_SLOT	0x00000008
-#define  CFG_HW_HAS_ETH0	0x00000010
-#define  CFG_HW_HAS_ETH1	0x00000020
-#define  CFG_HW_HAS_HSS0	0x00000040
-#define  CFG_HW_HAS_HSS1	0x00000080
-#define  CFG_HW_HAS_UART0	0x00000100
-#define  CFG_HW_HAS_UART1	0x00000200
-#define  CFG_HW_HAS_EEPROM	0x00000400
-
-#define FLASH_CMD_READ_ARRAY	0xFF
-#define FLASH_CMD_READ_ID	0x90
-#define FLASH_SER_OFF		0x102 /* 0x81 in 16-bit mode */
-
-static u32 hw_bits = 0xFFFFFFFD;    /* assume all hardware present */;
-static u8 control_value;
-
-/*
- * FIXME: this is reimplementing I2C bit-bangining. Move this
- * over to using driver/i2c/busses/i2c-gpio.c like all other boards
- * and register proper I2C device(s) on the bus for this. (See
- * other IXP4xx boards for examples.)
- */
-static void set_scl(u8 value)
-{
-	gpio_set_value(GPIO_SCL, !!value);
-	udelay(3);
-}
-
-static void set_sda(u8 value)
-{
-	gpio_set_value(GPIO_SDA, !!value);
-	udelay(3);
-}
-
-static void set_str(u8 value)
-{
-	gpio_set_value(GPIO_STR, !!value);
-	udelay(3);
-}
-
-static inline void set_control(int line, int value)
-{
-	if (value)
-		control_value |=  (1 << line);
-	else
-		control_value &= ~(1 << line);
-}
-
-
-static void output_control(void)
-{
-	int i;
-
-	gpio_direction_output(GPIO_SCL, 1);
-	gpio_direction_output(GPIO_SDA, 1);
-
-	for (i = 0; i < 8; i++) {
-		set_scl(0);
-		set_sda(control_value & (0x80 >> i)); /* MSB first */
-		set_scl(1);	/* active edge */
-	}
-
-	set_str(1);
-	set_str(0);
-
-	set_scl(0);
-	set_sda(1);		/* Be ready for START */
-	set_scl(1);
-}
-
-
-static void (*set_carrier_cb_tab[2])(void *pdev, int carrier);
-
-static int hss_set_clock(int port, unsigned int clock_type)
-{
-	int ctrl_int = port ? CONTROL_HSS1_CLK_INT : CONTROL_HSS0_CLK_INT;
-
-	switch (clock_type) {
-	case CLOCK_DEFAULT:
-	case CLOCK_EXT:
-		set_control(ctrl_int, 0);
-		output_control();
-		return CLOCK_EXT;
-
-	case CLOCK_INT:
-		set_control(ctrl_int, 1);
-		output_control();
-		return CLOCK_INT;
-
-	default:
-		return -EINVAL;
-	}
-}
-
-static irqreturn_t hss_dcd_irq(int irq, void *pdev)
-{
-	int port = (irq == IXP4XX_GPIO_IRQ(GPIO_HSS1_DCD_N));
-	int i = gpio_get_value(port ? GPIO_HSS1_DCD_N : GPIO_HSS0_DCD_N);
-	set_carrier_cb_tab[port](pdev, !i);
-	return IRQ_HANDLED;
-}
-
-
-static int hss_open(int port, void *pdev,
-		    void (*set_carrier_cb)(void *pdev, int carrier))
-{
-	int i, irq;
-
-	if (!port)
-		irq = IXP4XX_GPIO_IRQ(GPIO_HSS0_DCD_N);
-	else
-		irq = IXP4XX_GPIO_IRQ(GPIO_HSS1_DCD_N);
-
-	i = gpio_get_value(port ? GPIO_HSS1_DCD_N : GPIO_HSS0_DCD_N);
-	set_carrier_cb(pdev, !i);
-
-	set_carrier_cb_tab[!!port] = set_carrier_cb;
-
-	if ((i = request_irq(irq, hss_dcd_irq, 0, "IXP4xx HSS", pdev)) != 0) {
-		printk(KERN_ERR "ixp4xx_hss: failed to request IRQ%i (%i)\n",
-		       irq, i);
-		return i;
-	}
-
-	set_control(port ? CONTROL_HSS1_DTR_N : CONTROL_HSS0_DTR_N, 0);
-	output_control();
-	gpio_set_value(port ? GPIO_HSS1_RTS_N : GPIO_HSS0_RTS_N, 0);
-	return 0;
-}
-
-static void hss_close(int port, void *pdev)
-{
-	free_irq(port ? IXP4XX_GPIO_IRQ(GPIO_HSS1_DCD_N) :
-		 IXP4XX_GPIO_IRQ(GPIO_HSS0_DCD_N), pdev);
-	set_carrier_cb_tab[!!port] = NULL; /* catch bugs */
-
-	set_control(port ? CONTROL_HSS1_DTR_N : CONTROL_HSS0_DTR_N, 1);
-	output_control();
-	gpio_set_value(port ? GPIO_HSS1_RTS_N : GPIO_HSS0_RTS_N, 1);
-}
-
-
-/* Flash memory */
-static struct flash_platform_data flash_data = {
-	.map_name	= "cfi_probe",
-	.width		= 2,
-};
-
-static struct resource flash_resource = {
-	.flags		= IORESOURCE_MEM,
-};
-
-static struct platform_device device_flash = {
-	.name		= "IXP4XX-Flash",
-	.id		= 0,
-	.dev		= { .platform_data = &flash_data },
-	.num_resources	= 1,
-	.resource	= &flash_resource,
-};
-
-/* IXP425 2 UART ports */
-static struct resource uart_resources[] = {
-	{
-		.start		= IXP4XX_UART1_BASE_PHYS,
-		.end		= IXP4XX_UART1_BASE_PHYS + 0x0fff,
-		.flags		= IORESOURCE_MEM,
-	},
-	{
-		.start		= IXP4XX_UART2_BASE_PHYS,
-		.end		= IXP4XX_UART2_BASE_PHYS + 0x0fff,
-		.flags		= IORESOURCE_MEM,
-	}
-};
-
-static struct plat_serial8250_port uart_data[] = {
-	{
-		.mapbase	= IXP4XX_UART1_BASE_PHYS,
-		.membase	= (char __iomem *)IXP4XX_UART1_BASE_VIRT +
-			REG_OFFSET,
-		.irq		= IRQ_IXP4XX_UART1,
-		.flags		= UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
-		.iotype		= UPIO_MEM,
-		.regshift	= 2,
-		.uartclk	= IXP4XX_UART_XTAL,
-	},
-	{
-		.mapbase	= IXP4XX_UART2_BASE_PHYS,
-		.membase	= (char __iomem *)IXP4XX_UART2_BASE_VIRT +
-			REG_OFFSET,
-		.irq		= IRQ_IXP4XX_UART2,
-		.flags		= UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
-		.iotype		= UPIO_MEM,
-		.regshift	= 2,
-		.uartclk	= IXP4XX_UART_XTAL,
-	},
-	{ },
-};
-
-static struct platform_device device_uarts = {
-	.name			= "serial8250",
-	.id			= PLAT8250_DEV_PLATFORM,
-	.dev.platform_data	= uart_data,
-	.num_resources		= 2,
-	.resource		= uart_resources,
-};
-
-
-/* Built-in 10/100 Ethernet MAC interfaces */
-static struct resource eth_npeb_resources[] = {
-	{
-		.start		= IXP4XX_EthB_BASE_PHYS,
-		.end		= IXP4XX_EthB_BASE_PHYS + 0x0fff,
-		.flags		= IORESOURCE_MEM,
-	},
-};
-
-static struct resource eth_npec_resources[] = {
-	{
-		.start		= IXP4XX_EthC_BASE_PHYS,
-		.end		= IXP4XX_EthC_BASE_PHYS + 0x0fff,
-		.flags		= IORESOURCE_MEM,
-	},
-};
-
-static struct eth_plat_info eth_plat[] = {
-	{
-		.phy		= 0,
-		.rxq		= 3,
-		.txreadyq	= 32,
-	}, {
-		.phy		= 1,
-		.rxq		= 4,
-		.txreadyq	= 33,
-	}
-};
-
-static struct platform_device device_eth_tab[] = {
-	{
-		.name			= "ixp4xx_eth",
-		.id			= IXP4XX_ETH_NPEB,
-		.dev.platform_data	= eth_plat,
-		.num_resources		= ARRAY_SIZE(eth_npeb_resources),
-		.resource		= eth_npeb_resources,
-	}, {
-		.name			= "ixp4xx_eth",
-		.id			= IXP4XX_ETH_NPEC,
-		.dev.platform_data	= eth_plat + 1,
-		.num_resources		= ARRAY_SIZE(eth_npec_resources),
-		.resource		= eth_npec_resources,
-	}
-};
-
-
-/* IXP425 2 synchronous serial ports */
-static struct hss_plat_info hss_plat[] = {
-	{
-		.set_clock	= hss_set_clock,
-		.open		= hss_open,
-		.close		= hss_close,
-		.txreadyq	= 34,
-	}, {
-		.set_clock	= hss_set_clock,
-		.open		= hss_open,
-		.close		= hss_close,
-		.txreadyq	= 35,
-	}
-};
-
-static struct platform_device device_hss_tab[] = {
-	{
-		.name			= "ixp4xx_hss",
-		.id			= 0,
-		.dev.platform_data	= hss_plat,
-	}, {
-		.name			= "ixp4xx_hss",
-		.id			= 1,
-		.dev.platform_data	= hss_plat + 1,
-	}
-};
-
-
-static struct platform_device *device_tab[7] __initdata = {
-	&device_flash,		/* index 0 */
-};
-
-static inline u8 __init flash_readb(u8 __iomem *flash, u32 addr)
-{
-#ifdef __ARMEB__
-	return __raw_readb(flash + addr);
-#else
-	return __raw_readb(flash + (addr ^ 3));
-#endif
-}
-
-static inline u16 __init flash_readw(u8 __iomem *flash, u32 addr)
-{
-#ifdef __ARMEB__
-	return __raw_readw(flash + addr);
-#else
-	return __raw_readw(flash + (addr ^ 2));
-#endif
-}
-
-static void __init gmlr_init(void)
-{
-	u8 __iomem *flash;
-	int i, devices = 1; /* flash */
-
-	ixp4xx_sys_init();
-
-	if ((flash = ioremap(IXP4XX_EXP_BUS_BASE_PHYS, 0x80)) == NULL)
-		printk(KERN_ERR "goramo-mlr: unable to access system"
-		       " configuration data\n");
-	else {
-		system_rev = __raw_readl(flash + CFG_REV);
-		hw_bits = __raw_readl(flash + CFG_HW_BITS);
-
-		for (i = 0; i < ETH_ALEN; i++) {
-			eth_plat[0].hwaddr[i] =
-				flash_readb(flash, CFG_ETH0_ADDRESS + i);
-			eth_plat[1].hwaddr[i] =
-				flash_readb(flash, CFG_ETH1_ADDRESS + i);
-		}
-
-		__raw_writew(FLASH_CMD_READ_ID, flash);
-		system_serial_high = flash_readw(flash, FLASH_SER_OFF);
-		system_serial_high <<= 16;
-		system_serial_high |= flash_readw(flash, FLASH_SER_OFF + 2);
-		system_serial_low = flash_readw(flash, FLASH_SER_OFF + 4);
-		system_serial_low <<= 16;
-		system_serial_low |= flash_readw(flash, FLASH_SER_OFF + 6);
-		__raw_writew(FLASH_CMD_READ_ARRAY, flash);
-
-		iounmap(flash);
-	}
-
-	switch (hw_bits & (CFG_HW_HAS_UART0 | CFG_HW_HAS_UART1)) {
-	case CFG_HW_HAS_UART0:
-		memset(&uart_data[1], 0, sizeof(uart_data[1]));
-		device_uarts.num_resources = 1;
-		break;
-
-	case CFG_HW_HAS_UART1:
-		device_uarts.dev.platform_data = &uart_data[1];
-		device_uarts.resource = &uart_resources[1];
-		device_uarts.num_resources = 1;
-		break;
-	}
-	if (hw_bits & (CFG_HW_HAS_UART0 | CFG_HW_HAS_UART1))
-		device_tab[devices++] = &device_uarts; /* max index 1 */
-
-	if (hw_bits & CFG_HW_HAS_ETH0)
-		device_tab[devices++] = &device_eth_tab[0]; /* max index 2 */
-	if (hw_bits & CFG_HW_HAS_ETH1)
-		device_tab[devices++] = &device_eth_tab[1]; /* max index 3 */
-
-	if (hw_bits & CFG_HW_HAS_HSS0)
-		device_tab[devices++] = &device_hss_tab[0]; /* max index 4 */
-	if (hw_bits & CFG_HW_HAS_HSS1)
-		device_tab[devices++] = &device_hss_tab[1]; /* max index 5 */
-
-	hss_plat[0].timer_freq = ixp4xx_timer_freq;
-	hss_plat[1].timer_freq = ixp4xx_timer_freq;
-
-	gpio_request(GPIO_SCL, "SCL/clock");
-	gpio_request(GPIO_SDA, "SDA/data");
-	gpio_request(GPIO_STR, "strobe");
-	gpio_request(GPIO_HSS0_RTS_N, "HSS0 RTS");
-	gpio_request(GPIO_HSS1_RTS_N, "HSS1 RTS");
-	gpio_request(GPIO_HSS0_DCD_N, "HSS0 DCD");
-	gpio_request(GPIO_HSS1_DCD_N, "HSS1 DCD");
-
-	gpio_direction_output(GPIO_SCL, 1);
-	gpio_direction_output(GPIO_SDA, 1);
-	gpio_direction_output(GPIO_STR, 0);
-	gpio_direction_output(GPIO_HSS0_RTS_N, 1);
-	gpio_direction_output(GPIO_HSS1_RTS_N, 1);
-	gpio_direction_input(GPIO_HSS0_DCD_N);
-	gpio_direction_input(GPIO_HSS1_DCD_N);
-	irq_set_irq_type(IXP4XX_GPIO_IRQ(GPIO_HSS0_DCD_N), IRQ_TYPE_EDGE_BOTH);
-	irq_set_irq_type(IXP4XX_GPIO_IRQ(GPIO_HSS1_DCD_N), IRQ_TYPE_EDGE_BOTH);
-
-	set_control(CONTROL_HSS0_DTR_N, 1);
-	set_control(CONTROL_HSS1_DTR_N, 1);
-	set_control(CONTROL_EEPROM_WC_N, 1);
-	set_control(CONTROL_PCI_RESET_N, 1);
-	output_control();
-
-	msleep(1);	      /* Wait for PCI devices to initialize */
-
-	flash_resource.start = IXP4XX_EXP_BUS_BASE(0);
-	flash_resource.end = IXP4XX_EXP_BUS_BASE(0) + ixp4xx_exp_bus_size - 1;
-
-	platform_add_devices(device_tab, devices);
-}
-
-
-#ifdef CONFIG_PCI
-static void __init gmlr_pci_preinit(void)
-{
-	irq_set_irq_type(IXP4XX_GPIO_IRQ(GPIO_IRQ_ETHA), IRQ_TYPE_LEVEL_LOW);
-	irq_set_irq_type(IXP4XX_GPIO_IRQ(GPIO_IRQ_ETHB), IRQ_TYPE_LEVEL_LOW);
-	irq_set_irq_type(IXP4XX_GPIO_IRQ(GPIO_IRQ_NEC), IRQ_TYPE_LEVEL_LOW);
-	irq_set_irq_type(IXP4XX_GPIO_IRQ(GPIO_IRQ_MPCI), IRQ_TYPE_LEVEL_LOW);
-	ixp4xx_pci_preinit();
-}
-
-static void __init gmlr_pci_postinit(void)
-{
-	if ((hw_bits & CFG_HW_USB_PORTS) >= 2 &&
-	    (hw_bits & CFG_HW_USB_PORTS) < 5) {
-		/* need to adjust number of USB ports on NEC chip */
-		u32 value, addr = BIT(32 - SLOT_NEC) | 0xE0;
-		if (!ixp4xx_pci_read(addr, NP_CMD_CONFIGREAD, &value)) {
-			value &= ~7;
-			value |= (hw_bits & CFG_HW_USB_PORTS);
-			ixp4xx_pci_write(addr, NP_CMD_CONFIGWRITE, value);
-		}
-	}
-}
-
-static int __init gmlr_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
-{
-	switch(slot) {
-	case SLOT_ETHA:	return IXP4XX_GPIO_IRQ(GPIO_IRQ_ETHA);
-	case SLOT_ETHB:	return IXP4XX_GPIO_IRQ(GPIO_IRQ_ETHB);
-	case SLOT_NEC:	return IXP4XX_GPIO_IRQ(GPIO_IRQ_NEC);
-	default:	return IXP4XX_GPIO_IRQ(GPIO_IRQ_MPCI);
-	}
-}
-
-static struct hw_pci gmlr_hw_pci __initdata = {
-	.nr_controllers = 1,
-	.ops		= &ixp4xx_ops,
-	.preinit	= gmlr_pci_preinit,
-	.postinit	= gmlr_pci_postinit,
-	.setup		= ixp4xx_setup,
-	.map_irq	= gmlr_map_irq,
-};
-
-static int __init gmlr_pci_init(void)
-{
-	if (machine_is_goramo_mlr() &&
-	    (hw_bits & (CFG_HW_USB_PORTS | CFG_HW_HAS_PCI_SLOT)))
-		pci_common_init(&gmlr_hw_pci);
-	return 0;
-}
-
-subsys_initcall(gmlr_pci_init);
-#endif /* CONFIG_PCI */
-
-
-MACHINE_START(GORAMO_MLR, "MultiLink")
-	/* Maintainer: Krzysztof Halasa */
-	.map_io		= ixp4xx_map_io,
-	.init_early	= ixp4xx_init_early,
-	.init_irq	= ixp4xx_init_irq,
-	.init_time	= ixp4xx_timer_init,
-	.atag_offset	= 0x100,
-	.init_machine	= gmlr_init,
-#if defined(CONFIG_PCI)
-	.dma_zone_size	= SZ_64M,
-#endif
-	.restart	= ixp4xx_restart,
-MACHINE_END
diff --git a/arch/arm/mach-ixp4xx/include/mach/hardware.h b/arch/arm/mach-ixp4xx/include/mach/hardware.h
deleted file mode 100644
index b2b7301ce503..000000000000
--- a/arch/arm/mach-ixp4xx/include/mach/hardware.h
+++ /dev/null
@@ -1,32 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-only */
-/*
- * arch/arm/mach-ixp4xx/include/mach/hardware.h 
- *
- * Copyright (C) 2002 Intel Corporation.
- * Copyright (C) 2003-2004 MontaVista Software, Inc.
- */
-
-/*
- * Hardware definitions for IXP4xx based systems
- */
-
-#ifndef __ASM_ARCH_HARDWARE_H__
-#define __ASM_ARCH_HARDWARE_H__
-
-#ifdef CONFIG_IXP4XX_INDIRECT_PCI
-#define PCIBIOS_MAX_MEM		0x4FFFFFFF
-#else
-#define PCIBIOS_MAX_MEM		0x4BFFFFFF
-#endif
-
-/* Register locations and bits */
-#include "ixp4xx-regs.h"
-
-#ifndef __ASSEMBLER__
-#include <linux/soc/ixp4xx/cpu.h>
-#endif
-
-/* Platform helper functions and definitions */
-#include "platform.h"
-
-#endif  /* _ASM_ARCH_HARDWARE_H */
diff --git a/arch/arm/mach-ixp4xx/include/mach/io.h b/arch/arm/mach-ixp4xx/include/mach/io.h
deleted file mode 100644
index 014cf6dcaf8b..000000000000
--- a/arch/arm/mach-ixp4xx/include/mach/io.h
+++ /dev/null
@@ -1,545 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-only */
-/*
- * arch/arm/mach-ixp4xx/include/mach/io.h
- *
- * Author: Deepak Saxena <dsaxena@plexity.net>
- *
- * Copyright (C) 2002-2005  MontaVista Software, Inc.
- */
-
-#ifndef __ASM_ARM_ARCH_IO_H
-#define __ASM_ARM_ARCH_IO_H
-
-#include <linux/bitops.h>
-
-#include <mach/hardware.h>
-
-extern int (*ixp4xx_pci_read)(u32 addr, u32 cmd, u32* data);
-extern int ixp4xx_pci_write(u32 addr, u32 cmd, u32 data);
-
-
-/*
- * IXP4xx provides two methods of accessing PCI memory space:
- *
- * 1) A direct mapped window from 0x48000000 to 0x4BFFFFFF (64MB).
- *    To access PCI via this space, we simply ioremap() the BAR
- *    into the kernel and we can use the standard read[bwl]/write[bwl]
- *    macros. This is the preffered method due to speed but it
- *    limits the system to just 64MB of PCI memory. This can be
- *    problematic if using video cards and other memory-heavy targets.
- *
- * 2) If > 64MB of memory space is required, the IXP4xx can use indirect
- *    registers to access the whole 4 GB of PCI memory space (as we do below
- *    for I/O transactions). This allows currently for up to 1 GB (0x10000000
- *    to 0x4FFFFFFF) of memory on the bus. The disadvantage of this is that
- *    every PCI access requires three local register accesses plus a spinlock,
- *    but in some cases the performance hit is acceptable. In addition, you
- *    cannot mmap() PCI devices in this case.
- */
-#ifdef	CONFIG_IXP4XX_INDIRECT_PCI
-
-/*
- * In the case of using indirect PCI, we simply return the actual PCI
- * address and our read/write implementation use that to drive the 
- * access registers. If something outside of PCI is ioremap'd, we
- * fallback to the default.
- */
-
-extern unsigned long pcibios_min_mem;
-static inline int is_pci_memory(u32 addr)
-{
-	return (addr >= pcibios_min_mem) && (addr <= 0x4FFFFFFF);
-}
-
-#define writeb(v, p)			__indirect_writeb(v, p)
-#define writew(v, p)			__indirect_writew(v, p)
-#define writel(v, p)			__indirect_writel(v, p)
-
-#define writeb_relaxed(v, p)		__indirect_writeb(v, p)
-#define writew_relaxed(v, p)		__indirect_writew(v, p)
-#define writel_relaxed(v, p)		__indirect_writel(v, p)
-
-#define writesb(p, v, l)		__indirect_writesb(p, v, l)
-#define writesw(p, v, l)		__indirect_writesw(p, v, l)
-#define writesl(p, v, l)		__indirect_writesl(p, v, l)
-
-#define readb(p)			__indirect_readb(p)
-#define readw(p)			__indirect_readw(p)
-#define readl(p)			__indirect_readl(p)
-
-#define readb_relaxed(p)		__indirect_readb(p)
-#define readw_relaxed(p)		__indirect_readw(p)
-#define readl_relaxed(p)		__indirect_readl(p)
-
-#define readsb(p, v, l)			__indirect_readsb(p, v, l)
-#define readsw(p, v, l)			__indirect_readsw(p, v, l)
-#define readsl(p, v, l)			__indirect_readsl(p, v, l)
-
-static inline void __indirect_writeb(u8 value, volatile void __iomem *p)
-{
-	u32 addr = (u32)p;
-	u32 n, byte_enables, data;
-
-	if (!is_pci_memory(addr)) {
-		__raw_writeb(value, p);
-		return;
-	}
-
-	n = addr % 4;
-	byte_enables = (0xf & ~BIT(n)) << IXP4XX_PCI_NP_CBE_BESL;
-	data = value << (8*n);
-	ixp4xx_pci_write(addr, byte_enables | NP_CMD_MEMWRITE, data);
-}
-
-static inline void __indirect_writesb(volatile void __iomem *bus_addr,
-				      const void *p, int count)
-{
-	const u8 *vaddr = p;
-
-	while (count--)
-		writeb(*vaddr++, bus_addr);
-}
-
-static inline void __indirect_writew(u16 value, volatile void __iomem *p)
-{
-	u32 addr = (u32)p;
-	u32 n, byte_enables, data;
-
-	if (!is_pci_memory(addr)) {
-		__raw_writew(value, p);
-		return;
-	}
-
-	n = addr % 4;
-	byte_enables = (0xf & ~(BIT(n) | BIT(n+1))) << IXP4XX_PCI_NP_CBE_BESL;
-	data = value << (8*n);
-	ixp4xx_pci_write(addr, byte_enables | NP_CMD_MEMWRITE, data);
-}
-
-static inline void __indirect_writesw(volatile void __iomem *bus_addr,
-				      const void *p, int count)
-{
-	const u16 *vaddr = p;
-
-	while (count--)
-		writew(*vaddr++, bus_addr);
-}
-
-static inline void __indirect_writel(u32 value, volatile void __iomem *p)
-{
-	u32 addr = (__force u32)p;
-
-	if (!is_pci_memory(addr)) {
-		__raw_writel(value, p);
-		return;
-	}
-
-	ixp4xx_pci_write(addr, NP_CMD_MEMWRITE, value);
-}
-
-static inline void __indirect_writesl(volatile void __iomem *bus_addr,
-				      const void *p, int count)
-{
-	const u32 *vaddr = p;
-	while (count--)
-		writel(*vaddr++, bus_addr);
-}
-
-static inline u8 __indirect_readb(const volatile void __iomem *p)
-{
-	u32 addr = (u32)p;
-	u32 n, byte_enables, data;
-
-	if (!is_pci_memory(addr))
-		return __raw_readb(p);
-
-	n = addr % 4;
-	byte_enables = (0xf & ~BIT(n)) << IXP4XX_PCI_NP_CBE_BESL;
-	if (ixp4xx_pci_read(addr, byte_enables | NP_CMD_MEMREAD, &data))
-		return 0xff;
-
-	return data >> (8*n);
-}
-
-static inline void __indirect_readsb(const volatile void __iomem *bus_addr,
-				     void *p, u32 count)
-{
-	u8 *vaddr = p;
-
-	while (count--)
-		*vaddr++ = readb(bus_addr);
-}
-
-static inline u16 __indirect_readw(const volatile void __iomem *p)
-{
-	u32 addr = (u32)p;
-	u32 n, byte_enables, data;
-
-	if (!is_pci_memory(addr))
-		return __raw_readw(p);
-
-	n = addr % 4;
-	byte_enables = (0xf & ~(BIT(n) | BIT(n+1))) << IXP4XX_PCI_NP_CBE_BESL;
-	if (ixp4xx_pci_read(addr, byte_enables | NP_CMD_MEMREAD, &data))
-		return 0xffff;
-
-	return data>>(8*n);
-}
-
-static inline void __indirect_readsw(const volatile void __iomem *bus_addr,
-				     void *p, u32 count)
-{
-	u16 *vaddr = p;
-
-	while (count--)
-		*vaddr++ = readw(bus_addr);
-}
-
-static inline u32 __indirect_readl(const volatile void __iomem *p)
-{
-	u32 addr = (__force u32)p;
-	u32 data;
-
-	if (!is_pci_memory(addr))
-		return __raw_readl(p);
-
-	if (ixp4xx_pci_read(addr, NP_CMD_MEMREAD, &data))
-		return 0xffffffff;
-
-	return data;
-}
-
-static inline void __indirect_readsl(const volatile void __iomem *bus_addr,
-				     void *p, u32 count)
-{
-	u32 *vaddr = p;
-
-	while (count--)
-		*vaddr++ = readl(bus_addr);
-}
-
-
-/*
- * We can use the built-in functions b/c they end up calling writeb/readb
- */
-#define memset_io(c,v,l)		_memset_io((c),(v),(l))
-#define memcpy_fromio(a,c,l)		_memcpy_fromio((a),(c),(l))
-#define memcpy_toio(c,a,l)		_memcpy_toio((c),(a),(l))
-
-#endif /* CONFIG_IXP4XX_INDIRECT_PCI */
-
-#ifndef CONFIG_PCI
-
-#define	__io(v)		__typesafe_io(v)
-
-#else
-
-/*
- * IXP4xx does not have a transparent cpu -> PCI I/O translation
- * window.  Instead, it has a set of registers that must be tweaked
- * with the proper byte lanes, command types, and address for the
- * transaction.  This means that we need to override the default
- * I/O functions.
- */
-
-#define outb outb
-static inline void outb(u8 value, u32 addr)
-{
-	u32 n, byte_enables, data;
-	n = addr % 4;
-	byte_enables = (0xf & ~BIT(n)) << IXP4XX_PCI_NP_CBE_BESL;
-	data = value << (8*n);
-	ixp4xx_pci_write(addr, byte_enables | NP_CMD_IOWRITE, data);
-}
-
-#define outsb outsb
-static inline void outsb(u32 io_addr, const void *p, u32 count)
-{
-	const u8 *vaddr = p;
-
-	while (count--)
-		outb(*vaddr++, io_addr);
-}
-
-#define outw outw
-static inline void outw(u16 value, u32 addr)
-{
-	u32 n, byte_enables, data;
-	n = addr % 4;
-	byte_enables = (0xf & ~(BIT(n) | BIT(n+1))) << IXP4XX_PCI_NP_CBE_BESL;
-	data = value << (8*n);
-	ixp4xx_pci_write(addr, byte_enables | NP_CMD_IOWRITE, data);
-}
-
-#define outsw outsw
-static inline void outsw(u32 io_addr, const void *p, u32 count)
-{
-	const u16 *vaddr = p;
-	while (count--)
-		outw(cpu_to_le16(*vaddr++), io_addr);
-}
-
-#define outl outl
-static inline void outl(u32 value, u32 addr)
-{
-	ixp4xx_pci_write(addr, NP_CMD_IOWRITE, value);
-}
-
-#define outsl outsl
-static inline void outsl(u32 io_addr, const void *p, u32 count)
-{
-	const u32 *vaddr = p;
-	while (count--)
-		outl(cpu_to_le32(*vaddr++), io_addr);
-}
-
-#define inb inb
-static inline u8 inb(u32 addr)
-{
-	u32 n, byte_enables, data;
-	n = addr % 4;
-	byte_enables = (0xf & ~BIT(n)) << IXP4XX_PCI_NP_CBE_BESL;
-	if (ixp4xx_pci_read(addr, byte_enables | NP_CMD_IOREAD, &data))
-		return 0xff;
-
-	return data >> (8*n);
-}
-
-#define insb insb
-static inline void insb(u32 io_addr, void *p, u32 count)
-{
-	u8 *vaddr = p;
-	while (count--)
-		*vaddr++ = inb(io_addr);
-}
-
-#define inw inw
-static inline u16 inw(u32 addr)
-{
-	u32 n, byte_enables, data;
-	n = addr % 4;
-	byte_enables = (0xf & ~(BIT(n) | BIT(n+1))) << IXP4XX_PCI_NP_CBE_BESL;
-	if (ixp4xx_pci_read(addr, byte_enables | NP_CMD_IOREAD, &data))
-		return 0xffff;
-
-	return data>>(8*n);
-}
-
-#define insw insw
-static inline void insw(u32 io_addr, void *p, u32 count)
-{
-	u16 *vaddr = p;
-	while (count--)
-		*vaddr++ = le16_to_cpu(inw(io_addr));
-}
-
-#define inl inl
-static inline u32 inl(u32 addr)
-{
-	u32 data;
-	if (ixp4xx_pci_read(addr, NP_CMD_IOREAD, &data))
-		return 0xffffffff;
-
-	return data;
-}
-
-#define insl insl
-static inline void insl(u32 io_addr, void *p, u32 count)
-{
-	u32 *vaddr = p;
-	while (count--)
-		*vaddr++ = le32_to_cpu(inl(io_addr));
-}
-
-#define PIO_OFFSET      0x10000UL
-#define PIO_MASK        0x0ffffUL
-
-#define	__is_io_address(p)	(((unsigned long)p >= PIO_OFFSET) && \
-					((unsigned long)p <= (PIO_MASK + PIO_OFFSET)))
-
-#define	ioread8(p)			ioread8(p)
-static inline u8 ioread8(const void __iomem *addr)
-{
-	unsigned long port = (unsigned long __force)addr;
-	if (__is_io_address(port))
-		return (unsigned int)inb(port & PIO_MASK);
-	else
-#ifndef CONFIG_IXP4XX_INDIRECT_PCI
-		return (unsigned int)__raw_readb(addr);
-#else
-		return (unsigned int)__indirect_readb(addr);
-#endif
-}
-
-#define	ioread8_rep(p, v, c)		ioread8_rep(p, v, c)
-static inline void ioread8_rep(const void __iomem *addr, void *vaddr, u32 count)
-{
-	unsigned long port = (unsigned long __force)addr;
-	if (__is_io_address(port))
-		insb(port & PIO_MASK, vaddr, count);
-	else
-#ifndef	CONFIG_IXP4XX_INDIRECT_PCI
-		__raw_readsb(addr, vaddr, count);
-#else
-		__indirect_readsb(addr, vaddr, count);
-#endif
-}
-
-#define	ioread16(p)			ioread16(p)
-static inline u16 ioread16(const void __iomem *addr)
-{
-	unsigned long port = (unsigned long __force)addr;
-	if (__is_io_address(port))
-		return	(unsigned int)inw(port & PIO_MASK);
-	else
-#ifndef CONFIG_IXP4XX_INDIRECT_PCI
-		return le16_to_cpu((__force __le16)__raw_readw(addr));
-#else
-		return (unsigned int)__indirect_readw(addr);
-#endif
-}
-
-#define	ioread16_rep(p, v, c)		ioread16_rep(p, v, c)
-static inline void ioread16_rep(const void __iomem *addr, void *vaddr,
-				u32 count)
-{
-	unsigned long port = (unsigned long __force)addr;
-	if (__is_io_address(port))
-		insw(port & PIO_MASK, vaddr, count);
-	else
-#ifndef	CONFIG_IXP4XX_INDIRECT_PCI
-		__raw_readsw(addr, vaddr, count);
-#else
-		__indirect_readsw(addr, vaddr, count);
-#endif
-}
-
-#define	ioread32(p)			ioread32(p)
-static inline u32 ioread32(const void __iomem *addr)
-{
-	unsigned long port = (unsigned long __force)addr;
-	if (__is_io_address(port))
-		return	(unsigned int)inl(port & PIO_MASK);
-	else {
-#ifndef CONFIG_IXP4XX_INDIRECT_PCI
-		return le32_to_cpu((__force __le32)__raw_readl(addr));
-#else
-		return (unsigned int)__indirect_readl(addr);
-#endif
-	}
-}
-
-#define	ioread32_rep(p, v, c)		ioread32_rep(p, v, c)
-static inline void ioread32_rep(const void __iomem *addr, void *vaddr,
-				u32 count)
-{
-	unsigned long port = (unsigned long __force)addr;
-	if (__is_io_address(port))
-		insl(port & PIO_MASK, vaddr, count);
-	else
-#ifndef	CONFIG_IXP4XX_INDIRECT_PCI
-		__raw_readsl(addr, vaddr, count);
-#else
-		__indirect_readsl(addr, vaddr, count);
-#endif
-}
-
-#define	iowrite8(v, p)			iowrite8(v, p)
-static inline void iowrite8(u8 value, void __iomem *addr)
-{
-	unsigned long port = (unsigned long __force)addr;
-	if (__is_io_address(port))
-		outb(value, port & PIO_MASK);
-	else
-#ifndef CONFIG_IXP4XX_INDIRECT_PCI
-		__raw_writeb(value, addr);
-#else
-		__indirect_writeb(value, addr);
-#endif
-}
-
-#define	iowrite8_rep(p, v, c)		iowrite8_rep(p, v, c)
-static inline void iowrite8_rep(void __iomem *addr, const void *vaddr,
-				u32 count)
-{
-	unsigned long port = (unsigned long __force)addr;
-	if (__is_io_address(port))
-		outsb(port & PIO_MASK, vaddr, count);
-	else
-#ifndef CONFIG_IXP4XX_INDIRECT_PCI
-		__raw_writesb(addr, vaddr, count);
-#else
-		__indirect_writesb(addr, vaddr, count);
-#endif
-}
-
-#define	iowrite16(v, p)			iowrite16(v, p)
-static inline void iowrite16(u16 value, void __iomem *addr)
-{
-	unsigned long port = (unsigned long __force)addr;
-	if (__is_io_address(port))
-		outw(value, port & PIO_MASK);
-	else
-#ifndef CONFIG_IXP4XX_INDIRECT_PCI
-		__raw_writew(cpu_to_le16(value), addr);
-#else
-		__indirect_writew(value, addr);
-#endif
-}
-
-#define	iowrite16_rep(p, v, c)		iowrite16_rep(p, v, c)
-static inline void iowrite16_rep(void __iomem *addr, const void *vaddr,
-				 u32 count)
-{
-	unsigned long port = (unsigned long __force)addr;
-	if (__is_io_address(port))
-		outsw(port & PIO_MASK, vaddr, count);
-	else
-#ifndef CONFIG_IXP4XX_INDIRECT_PCI
-		__raw_writesw(addr, vaddr, count);
-#else
-		__indirect_writesw(addr, vaddr, count);
-#endif
-}
-
-#define	iowrite32(v, p)			iowrite32(v, p)
-static inline void iowrite32(u32 value, void __iomem *addr)
-{
-	unsigned long port = (unsigned long __force)addr;
-	if (__is_io_address(port))
-		outl(value, port & PIO_MASK);
-	else
-#ifndef CONFIG_IXP4XX_INDIRECT_PCI
-		__raw_writel((u32 __force)cpu_to_le32(value), addr);
-#else
-		__indirect_writel(value, addr);
-#endif
-}
-
-#define	iowrite32_rep(p, v, c)		iowrite32_rep(p, v, c)
-static inline void iowrite32_rep(void __iomem *addr, const void *vaddr,
-				 u32 count)
-{
-	unsigned long port = (unsigned long __force)addr;
-	if (__is_io_address(port))
-		outsl(port & PIO_MASK, vaddr, count);
-	else
-#ifndef CONFIG_IXP4XX_INDIRECT_PCI
-		__raw_writesl(addr, vaddr, count);
-#else
-		__indirect_writesl(addr, vaddr, count);
-#endif
-}
-
-#define ioport_map(port, nr) ioport_map(port, nr)
-static inline void __iomem *ioport_map(unsigned long port, unsigned int nr)
-{
-	return ((void __iomem*)((port) + PIO_OFFSET));
-}
-#define	ioport_unmap(addr) ioport_unmap(addr)
-static inline void ioport_unmap(void __iomem *addr)
-{
-}
-#endif /* CONFIG_PCI */
-
-#endif /* __ASM_ARM_ARCH_IO_H */
diff --git a/arch/arm/mach-ixp4xx/include/mach/ixp4xx-regs.h b/arch/arm/mach-ixp4xx/include/mach/ixp4xx-regs.h
deleted file mode 100644
index 74e63d4531aa..000000000000
--- a/arch/arm/mach-ixp4xx/include/mach/ixp4xx-regs.h
+++ /dev/null
@@ -1,303 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-only */
-/*
- * arch/arm/mach-ixp4xx/include/mach/ixp4xx-regs.h
- *
- * Register definitions for IXP4xx chipset. This file contains 
- * register location and bit definitions only. Platform specific 
- * definitions and helper function declarations are in platform.h 
- * and machine-name.h.
- *
- * Copyright (C) 2002 Intel Corporation.
- * Copyright (C) 2003-2004 MontaVista Software, Inc.
- */
-
-#ifndef _ASM_ARM_IXP4XX_H_
-#define _ASM_ARM_IXP4XX_H_
-
-/*
- * IXP4xx Linux Memory Map:
- *
- * Phy		Size		Virt		Description
- * =========================================================================
- *
- * 0x00000000	0x10000000(max)	PAGE_OFFSET	System RAM
- *
- * 0x48000000	0x04000000	ioremap'd	PCI Memory Space
- *
- * 0x50000000	0x10000000	ioremap'd	EXP BUS
- *
- * 0xC8000000	0x00013000	0xFEF00000	On-Chip Peripherals
- *
- * 0xC0000000	0x00001000	0xFEF13000	PCI CFG
- *
- * 0xC4000000	0x00001000	0xFEF14000	EXP CFG
- *
- * 0x60000000	0x00004000	0xFEF15000	QMgr
- */
-
-/*
- * Queue Manager
- */
-#define IXP4XX_QMGR_BASE_PHYS		0x60000000
-
-/*
- * Peripheral space, including debug UART. Must be section-aligned so that
- * it can be used with the low-level debug code.
- */
-#define IXP4XX_PERIPHERAL_BASE_PHYS	0xC8000000
-#define IXP4XX_PERIPHERAL_BASE_VIRT	IOMEM(0xFEC00000)
-#define IXP4XX_PERIPHERAL_REGION_SIZE	0x00013000
-
-/*
- * PCI Config registers
- */
-#define IXP4XX_PCI_CFG_BASE_PHYS	0xC0000000
-#define IXP4XX_PCI_CFG_BASE_VIRT	IOMEM(0xFEC13000)
-#define IXP4XX_PCI_CFG_REGION_SIZE	0x00001000
-
-/*
- * Expansion BUS Configuration registers
- */
-#define IXP4XX_EXP_CFG_BASE_PHYS	0xC4000000
-#define IXP4XX_EXP_CFG_BASE_VIRT	0xFEC14000
-#define IXP4XX_EXP_CFG_REGION_SIZE	0x00001000
-
-#define IXP4XX_EXP_CS0_OFFSET	0x00
-#define IXP4XX_EXP_CS1_OFFSET   0x04
-#define IXP4XX_EXP_CS2_OFFSET   0x08
-#define IXP4XX_EXP_CS3_OFFSET   0x0C
-#define IXP4XX_EXP_CS4_OFFSET   0x10
-#define IXP4XX_EXP_CS5_OFFSET   0x14
-#define IXP4XX_EXP_CS6_OFFSET   0x18
-#define IXP4XX_EXP_CS7_OFFSET   0x1C
-#define IXP4XX_EXP_CFG0_OFFSET	0x20
-#define IXP4XX_EXP_CFG1_OFFSET	0x24
-#define IXP4XX_EXP_CFG2_OFFSET	0x28
-#define IXP4XX_EXP_CFG3_OFFSET	0x2C
-
-/*
- * Expansion Bus Controller registers.
- */
-#define IXP4XX_EXP_REG(x) ((volatile u32 __iomem *)(IXP4XX_EXP_CFG_BASE_VIRT+(x)))
-
-#define IXP4XX_EXP_CS0      IXP4XX_EXP_REG(IXP4XX_EXP_CS0_OFFSET)
-#define IXP4XX_EXP_CS1      IXP4XX_EXP_REG(IXP4XX_EXP_CS1_OFFSET)
-#define IXP4XX_EXP_CS2      IXP4XX_EXP_REG(IXP4XX_EXP_CS2_OFFSET) 
-#define IXP4XX_EXP_CS3      IXP4XX_EXP_REG(IXP4XX_EXP_CS3_OFFSET)
-#define IXP4XX_EXP_CS4      IXP4XX_EXP_REG(IXP4XX_EXP_CS4_OFFSET)
-#define IXP4XX_EXP_CS5      IXP4XX_EXP_REG(IXP4XX_EXP_CS5_OFFSET)
-#define IXP4XX_EXP_CS6      IXP4XX_EXP_REG(IXP4XX_EXP_CS6_OFFSET)     
-#define IXP4XX_EXP_CS7      IXP4XX_EXP_REG(IXP4XX_EXP_CS7_OFFSET)
-
-#define IXP4XX_EXP_CFG0     IXP4XX_EXP_REG(IXP4XX_EXP_CFG0_OFFSET) 
-#define IXP4XX_EXP_CFG1     IXP4XX_EXP_REG(IXP4XX_EXP_CFG1_OFFSET) 
-#define IXP4XX_EXP_CFG2     IXP4XX_EXP_REG(IXP4XX_EXP_CFG2_OFFSET) 
-#define IXP4XX_EXP_CFG3     IXP4XX_EXP_REG(IXP4XX_EXP_CFG3_OFFSET)
-
-
-/*
- * Peripheral Space Register Region Base Addresses
- */
-#define IXP4XX_UART1_BASE_PHYS		(IXP4XX_PERIPHERAL_BASE_PHYS + 0x0000)
-#define IXP4XX_UART2_BASE_PHYS		(IXP4XX_PERIPHERAL_BASE_PHYS + 0x1000)
-#define IXP4XX_PMU_BASE_PHYS		(IXP4XX_PERIPHERAL_BASE_PHYS + 0x2000)
-#define IXP4XX_INTC_BASE_PHYS		(IXP4XX_PERIPHERAL_BASE_PHYS + 0x3000)
-#define IXP4XX_GPIO_BASE_PHYS		(IXP4XX_PERIPHERAL_BASE_PHYS + 0x4000)
-#define IXP4XX_TIMER_BASE_PHYS		(IXP4XX_PERIPHERAL_BASE_PHYS + 0x5000)
-#define IXP4XX_NPEA_BASE_PHYS   	(IXP4XX_PERIPHERAL_BASE_PHYS + 0x6000)
-#define IXP4XX_NPEB_BASE_PHYS   	(IXP4XX_PERIPHERAL_BASE_PHYS + 0x7000)
-#define IXP4XX_NPEC_BASE_PHYS   	(IXP4XX_PERIPHERAL_BASE_PHYS + 0x8000)
-#define IXP4XX_EthB_BASE_PHYS		(IXP4XX_PERIPHERAL_BASE_PHYS + 0x9000)
-#define IXP4XX_EthC_BASE_PHYS		(IXP4XX_PERIPHERAL_BASE_PHYS + 0xA000)
-#define IXP4XX_USB_BASE_PHYS		(IXP4XX_PERIPHERAL_BASE_PHYS + 0xB000)
-/* ixp46X only */
-#define IXP4XX_EthA_BASE_PHYS		(IXP4XX_PERIPHERAL_BASE_PHYS + 0xC000)
-#define IXP4XX_EthB1_BASE_PHYS		(IXP4XX_PERIPHERAL_BASE_PHYS + 0xD000)
-#define IXP4XX_EthB2_BASE_PHYS		(IXP4XX_PERIPHERAL_BASE_PHYS + 0xE000)
-#define IXP4XX_EthB3_BASE_PHYS		(IXP4XX_PERIPHERAL_BASE_PHYS + 0xF000)
-#define IXP4XX_TIMESYNC_BASE_PHYS	(IXP4XX_PERIPHERAL_BASE_PHYS + 0x10000)
-#define IXP4XX_I2C_BASE_PHYS		(IXP4XX_PERIPHERAL_BASE_PHYS + 0x11000)
-#define IXP4XX_SSP_BASE_PHYS		(IXP4XX_PERIPHERAL_BASE_PHYS + 0x12000)
-
-
-/* The UART is explicitly put in the beginning of fixmap */
-#define IXP4XX_UART1_BASE_VIRT		(IXP4XX_PERIPHERAL_BASE_VIRT + 0x0000)
-#define IXP4XX_UART2_BASE_VIRT		(IXP4XX_PERIPHERAL_BASE_VIRT + 0x1000)
-#define IXP4XX_PMU_BASE_VIRT		(IXP4XX_PERIPHERAL_BASE_VIRT + 0x2000)
-#define IXP4XX_INTC_BASE_VIRT		(IXP4XX_PERIPHERAL_BASE_VIRT + 0x3000)
-#define IXP4XX_GPIO_BASE_VIRT		(IXP4XX_PERIPHERAL_BASE_VIRT + 0x4000)
-#define IXP4XX_TIMER_BASE_VIRT		(IXP4XX_PERIPHERAL_BASE_VIRT + 0x5000)
-#define IXP4XX_EthB_BASE_VIRT		(IXP4XX_PERIPHERAL_BASE_VIRT + 0x9000)
-#define IXP4XX_EthC_BASE_VIRT		(IXP4XX_PERIPHERAL_BASE_VIRT + 0xA000)
-#define IXP4XX_USB_BASE_VIRT		(IXP4XX_PERIPHERAL_BASE_VIRT + 0xB000)
-/* ixp46X only */
-#define IXP4XX_EthA_BASE_VIRT		(IXP4XX_PERIPHERAL_BASE_VIRT + 0xC000)
-#define IXP4XX_EthB1_BASE_VIRT		(IXP4XX_PERIPHERAL_BASE_VIRT + 0xD000)
-#define IXP4XX_EthB2_BASE_VIRT		(IXP4XX_PERIPHERAL_BASE_VIRT + 0xE000)
-#define IXP4XX_EthB3_BASE_VIRT		(IXP4XX_PERIPHERAL_BASE_VIRT + 0xF000)
-#define IXP4XX_TIMESYNC_BASE_VIRT	(IXP4XX_PERIPHERAL_BASE_VIRT + 0x10000)
-#define IXP4XX_I2C_BASE_VIRT		(IXP4XX_PERIPHERAL_BASE_VIRT + 0x11000)
-#define IXP4XX_SSP_BASE_VIRT		(IXP4XX_PERIPHERAL_BASE_VIRT + 0x12000)
-
-/*
- * Constants to make it easy to access Timer Control/Status registers
- */
-#define IXP4XX_OSTS_OFFSET	0x00  /* Continious TimeStamp */
-#define IXP4XX_OST1_OFFSET	0x04  /* Timer 1 Timestamp */
-#define IXP4XX_OSRT1_OFFSET	0x08  /* Timer 1 Reload */
-#define IXP4XX_OST2_OFFSET	0x0C  /* Timer 2 Timestamp */
-#define IXP4XX_OSRT2_OFFSET	0x10  /* Timer 2 Reload */
-#define IXP4XX_OSWT_OFFSET	0x14  /* Watchdog Timer */
-#define IXP4XX_OSWE_OFFSET	0x18  /* Watchdog Enable */
-#define IXP4XX_OSWK_OFFSET	0x1C  /* Watchdog Key */
-#define IXP4XX_OSST_OFFSET	0x20  /* Timer Status */
-
-/*
- * Operating System Timer Register Definitions.
- */
-
-#define IXP4XX_TIMER_REG(x) ((volatile u32 *)(IXP4XX_TIMER_BASE_VIRT+(x)))
-
-#define IXP4XX_OSTS	IXP4XX_TIMER_REG(IXP4XX_OSTS_OFFSET)
-#define IXP4XX_OST1	IXP4XX_TIMER_REG(IXP4XX_OST1_OFFSET)
-#define IXP4XX_OSRT1	IXP4XX_TIMER_REG(IXP4XX_OSRT1_OFFSET)
-#define IXP4XX_OST2	IXP4XX_TIMER_REG(IXP4XX_OST2_OFFSET)
-#define IXP4XX_OSRT2	IXP4XX_TIMER_REG(IXP4XX_OSRT2_OFFSET)
-#define IXP4XX_OSWT	IXP4XX_TIMER_REG(IXP4XX_OSWT_OFFSET)
-#define IXP4XX_OSWE	IXP4XX_TIMER_REG(IXP4XX_OSWE_OFFSET)
-#define IXP4XX_OSWK	IXP4XX_TIMER_REG(IXP4XX_OSWK_OFFSET)
-#define IXP4XX_OSST	IXP4XX_TIMER_REG(IXP4XX_OSST_OFFSET)
-
-/*
- * Timer register values and bit definitions 
- */
-#define IXP4XX_OST_ENABLE		0x00000001
-#define IXP4XX_OST_ONE_SHOT		0x00000002
-/* Low order bits of reload value ignored */
-#define IXP4XX_OST_RELOAD_MASK		0x00000003
-#define IXP4XX_OST_DISABLED		0x00000000
-#define IXP4XX_OSST_TIMER_1_PEND	0x00000001
-#define IXP4XX_OSST_TIMER_2_PEND	0x00000002
-#define IXP4XX_OSST_TIMER_TS_PEND	0x00000004
-#define IXP4XX_OSST_TIMER_WDOG_PEND	0x00000008
-#define IXP4XX_OSST_TIMER_WARM_RESET	0x00000010
-
-#define	IXP4XX_WDT_KEY			0x0000482E
-
-#define	IXP4XX_WDT_RESET_ENABLE		0x00000001
-#define	IXP4XX_WDT_IRQ_ENABLE		0x00000002
-#define	IXP4XX_WDT_COUNT_ENABLE		0x00000004
-
-
-/*
- * Constants to make it easy to access PCI Control/Status registers
- */
-#define PCI_NP_AD_OFFSET            0x00
-#define PCI_NP_CBE_OFFSET           0x04
-#define PCI_NP_WDATA_OFFSET         0x08
-#define PCI_NP_RDATA_OFFSET         0x0c
-#define PCI_CRP_AD_CBE_OFFSET       0x10
-#define PCI_CRP_WDATA_OFFSET        0x14
-#define PCI_CRP_RDATA_OFFSET        0x18
-#define PCI_CSR_OFFSET              0x1c
-#define PCI_ISR_OFFSET              0x20
-#define PCI_INTEN_OFFSET            0x24
-#define PCI_DMACTRL_OFFSET          0x28
-#define PCI_AHBMEMBASE_OFFSET       0x2c
-#define PCI_AHBIOBASE_OFFSET        0x30
-#define PCI_PCIMEMBASE_OFFSET       0x34
-#define PCI_AHBDOORBELL_OFFSET      0x38
-#define PCI_PCIDOORBELL_OFFSET      0x3C
-#define PCI_ATPDMA0_AHBADDR_OFFSET  0x40
-#define PCI_ATPDMA0_PCIADDR_OFFSET  0x44
-#define PCI_ATPDMA0_LENADDR_OFFSET  0x48
-#define PCI_ATPDMA1_AHBADDR_OFFSET  0x4C
-#define PCI_ATPDMA1_PCIADDR_OFFSET  0x50
-#define PCI_ATPDMA1_LENADDR_OFFSET	0x54
-
-/*
- * PCI Control/Status Registers
- */
-#define _IXP4XX_PCI_CSR(x) ((volatile u32 *)(IXP4XX_PCI_CFG_BASE_VIRT+(x)))
-
-#define PCI_NP_AD               _IXP4XX_PCI_CSR(PCI_NP_AD_OFFSET)
-#define PCI_NP_CBE              _IXP4XX_PCI_CSR(PCI_NP_CBE_OFFSET)
-#define PCI_NP_WDATA            _IXP4XX_PCI_CSR(PCI_NP_WDATA_OFFSET)
-#define PCI_NP_RDATA            _IXP4XX_PCI_CSR(PCI_NP_RDATA_OFFSET)
-#define PCI_CRP_AD_CBE          _IXP4XX_PCI_CSR(PCI_CRP_AD_CBE_OFFSET)
-#define PCI_CRP_WDATA           _IXP4XX_PCI_CSR(PCI_CRP_WDATA_OFFSET)
-#define PCI_CRP_RDATA           _IXP4XX_PCI_CSR(PCI_CRP_RDATA_OFFSET)
-#define PCI_CSR                 _IXP4XX_PCI_CSR(PCI_CSR_OFFSET) 
-#define PCI_ISR                 _IXP4XX_PCI_CSR(PCI_ISR_OFFSET)
-#define PCI_INTEN               _IXP4XX_PCI_CSR(PCI_INTEN_OFFSET)
-#define PCI_DMACTRL             _IXP4XX_PCI_CSR(PCI_DMACTRL_OFFSET)
-#define PCI_AHBMEMBASE          _IXP4XX_PCI_CSR(PCI_AHBMEMBASE_OFFSET)
-#define PCI_AHBIOBASE           _IXP4XX_PCI_CSR(PCI_AHBIOBASE_OFFSET)
-#define PCI_PCIMEMBASE          _IXP4XX_PCI_CSR(PCI_PCIMEMBASE_OFFSET)
-#define PCI_AHBDOORBELL         _IXP4XX_PCI_CSR(PCI_AHBDOORBELL_OFFSET)
-#define PCI_PCIDOORBELL         _IXP4XX_PCI_CSR(PCI_PCIDOORBELL_OFFSET)
-#define PCI_ATPDMA0_AHBADDR     _IXP4XX_PCI_CSR(PCI_ATPDMA0_AHBADDR_OFFSET)
-#define PCI_ATPDMA0_PCIADDR     _IXP4XX_PCI_CSR(PCI_ATPDMA0_PCIADDR_OFFSET)
-#define PCI_ATPDMA0_LENADDR     _IXP4XX_PCI_CSR(PCI_ATPDMA0_LENADDR_OFFSET)
-#define PCI_ATPDMA1_AHBADDR     _IXP4XX_PCI_CSR(PCI_ATPDMA1_AHBADDR_OFFSET)
-#define PCI_ATPDMA1_PCIADDR     _IXP4XX_PCI_CSR(PCI_ATPDMA1_PCIADDR_OFFSET)
-#define PCI_ATPDMA1_LENADDR     _IXP4XX_PCI_CSR(PCI_ATPDMA1_LENADDR_OFFSET)
-
-/*
- * PCI register values and bit definitions 
- */
-
-/* CSR bit definitions */
-#define PCI_CSR_HOST    	0x00000001
-#define PCI_CSR_ARBEN   	0x00000002
-#define PCI_CSR_ADS     	0x00000004
-#define PCI_CSR_PDS     	0x00000008
-#define PCI_CSR_ABE     	0x00000010
-#define PCI_CSR_DBT     	0x00000020
-#define PCI_CSR_ASE     	0x00000100
-#define PCI_CSR_IC      	0x00008000
-
-/* ISR (Interrupt status) Register bit definitions */
-#define PCI_ISR_PSE     	0x00000001
-#define PCI_ISR_PFE     	0x00000002
-#define PCI_ISR_PPE     	0x00000004
-#define PCI_ISR_AHBE    	0x00000008
-#define PCI_ISR_APDC    	0x00000010
-#define PCI_ISR_PADC    	0x00000020
-#define PCI_ISR_ADB     	0x00000040
-#define PCI_ISR_PDB     	0x00000080
-
-/* INTEN (Interrupt Enable) Register bit definitions */
-#define PCI_INTEN_PSE   	0x00000001
-#define PCI_INTEN_PFE   	0x00000002
-#define PCI_INTEN_PPE   	0x00000004
-#define PCI_INTEN_AHBE  	0x00000008
-#define PCI_INTEN_APDC  	0x00000010
-#define PCI_INTEN_PADC  	0x00000020
-#define PCI_INTEN_ADB   	0x00000040
-#define PCI_INTEN_PDB   	0x00000080
-
-/*
- * Shift value for byte enable on NP cmd/byte enable register
- */
-#define IXP4XX_PCI_NP_CBE_BESL		4
-
-/*
- * PCI commands supported by NP access unit
- */
-#define NP_CMD_IOREAD			0x2
-#define NP_CMD_IOWRITE			0x3
-#define NP_CMD_CONFIGREAD		0xa
-#define NP_CMD_CONFIGWRITE		0xb
-#define NP_CMD_MEMREAD			0x6
-#define	NP_CMD_MEMWRITE			0x7
-
-/*
- * Constants for CRP access into local config space
- */
-#define CRP_AD_CBE_BESL         20
-#define CRP_AD_CBE_WRITE	0x00010000
-
-#define DCMD_LENGTH	0x01fff		/* length mask (max = 8K - 1) */
-
-#endif
diff --git a/arch/arm/mach-ixp4xx/include/mach/platform.h b/arch/arm/mach-ixp4xx/include/mach/platform.h
deleted file mode 100644
index d8b4df96db08..000000000000
--- a/arch/arm/mach-ixp4xx/include/mach/platform.h
+++ /dev/null
@@ -1,102 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-/*
- * arch/arm/mach-ixp4xx/include/mach/platform.h
- *
- * Constants and functions that are useful to IXP4xx platform-specific code
- * and device drivers.
- *
- * Copyright (C) 2004 MontaVista Software, Inc.
- */
-
-#ifndef __ASM_ARCH_HARDWARE_H__
-#error "Do not include this directly, instead #include <mach/hardware.h>"
-#endif
-
-#ifndef __ASSEMBLY__
-
-#include <linux/reboot.h>
-#include <linux/platform_data/eth_ixp4xx.h>
-
-#include <asm/types.h>
-
-#ifndef	__ARMEB__
-#define	REG_OFFSET	0
-#else
-#define	REG_OFFSET	3
-#endif
-
-/*
- * Expansion bus memory regions
- */
-#define IXP4XX_EXP_BUS_BASE_PHYS	(0x50000000)
-
-/*
- * The expansion bus on the IXP4xx can be configured for either 16 or
- * 32MB windows and the CS offset for each region changes based on the
- * current configuration. This means that we cannot simply hardcode
- * each offset. ixp4xx_sys_init() looks at the expansion bus configuration
- * as setup by the bootloader to determine our window size.
- */
-extern unsigned long ixp4xx_exp_bus_size;
-
-#define	IXP4XX_EXP_BUS_BASE(region)\
-		(IXP4XX_EXP_BUS_BASE_PHYS + ((region) * ixp4xx_exp_bus_size))
-
-#define IXP4XX_EXP_BUS_END(region)\
-		(IXP4XX_EXP_BUS_BASE(region) + ixp4xx_exp_bus_size - 1)
-
-/* Those macros can be used to adjust timing and configure
- * other features for each region.
- */
-
-#define IXP4XX_EXP_BUS_RECOVERY_T(x)	(((x) & 0x0f) << 16)
-#define IXP4XX_EXP_BUS_HOLD_T(x)	(((x) & 0x03) << 20)
-#define IXP4XX_EXP_BUS_STROBE_T(x)	(((x) & 0x0f) << 22)
-#define IXP4XX_EXP_BUS_SETUP_T(x)	(((x) & 0x03) << 26)
-#define IXP4XX_EXP_BUS_ADDR_T(x)	(((x) & 0x03) << 28)
-#define IXP4XX_EXP_BUS_SIZE(x)		(((x) & 0x0f) << 10)
-#define IXP4XX_EXP_BUS_CYCLES(x)	(((x) & 0x03) << 14)
-
-#define IXP4XX_EXP_BUS_CS_EN		(1L << 31)
-#define IXP4XX_EXP_BUS_BYTE_RD16	(1L << 6)
-#define IXP4XX_EXP_BUS_HRDY_POL		(1L << 5)
-#define IXP4XX_EXP_BUS_MUX_EN		(1L << 4)
-#define IXP4XX_EXP_BUS_SPLT_EN		(1L << 3)
-#define IXP4XX_EXP_BUS_WR_EN		(1L << 1)
-#define IXP4XX_EXP_BUS_BYTE_EN		(1L << 0)
-
-#define IXP4XX_EXP_BUS_CYCLES_INTEL	0x00
-#define IXP4XX_EXP_BUS_CYCLES_MOTOROLA	0x01
-#define IXP4XX_EXP_BUS_CYCLES_HPI	0x02
-
-#define IXP4XX_FLASH_WRITABLE	(0x2)
-#define IXP4XX_FLASH_DEFAULT	(0xbcd23c40)
-#define IXP4XX_FLASH_WRITE	(0xbcd23c42)
-
-/*
- * Clock Speed Definitions.
- */
-#define IXP4XX_PERIPHERAL_BUS_CLOCK 	(66) /* 66MHzi APB BUS   */ 
-#define IXP4XX_UART_XTAL        	14745600
-
-/*
- * Frequency of clock used for primary clocksource
- */
-extern unsigned long ixp4xx_timer_freq;
-
-/*
- * Functions used by platform-level setup code
- */
-extern void ixp4xx_map_io(void);
-extern void ixp4xx_init_early(void);
-extern void ixp4xx_init_irq(void);
-extern void ixp4xx_sys_init(void);
-extern void ixp4xx_timer_init(void);
-extern void ixp4xx_restart(enum reboot_mode, const char *);
-extern void ixp4xx_pci_preinit(void);
-struct pci_sys_data;
-extern int ixp4xx_setup(int nr, struct pci_sys_data *sys);
-extern struct pci_ops ixp4xx_ops;
-
-#endif // __ASSEMBLY__
-
diff --git a/arch/arm/mach-ixp4xx/include/mach/udc.h b/arch/arm/mach-ixp4xx/include/mach/udc.h
deleted file mode 100644
index 7bd8b96c8843..000000000000
--- a/arch/arm/mach-ixp4xx/include/mach/udc.h
+++ /dev/null
@@ -1,8 +0,0 @@
-/*
- * arch/arm/mach-ixp4xx/include/mach/udc.h
- *
- */
-#include <linux/platform_data/pxa2xx_udc.h>
-
-extern void ixp4xx_set_udc_info(struct pxa2xx_udc_mach_info *info);
-
diff --git a/arch/arm/mach-ixp4xx/include/mach/uncompress.h b/arch/arm/mach-ixp4xx/include/mach/uncompress.h
deleted file mode 100644
index 9e08b270cfc7..000000000000
--- a/arch/arm/mach-ixp4xx/include/mach/uncompress.h
+++ /dev/null
@@ -1,52 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-only */
-/*
- * arch/arm/mach-ixp4xx/include/mach/uncompress.h 
- *
- * Copyright (C) 2002 Intel Corporation.
- * Copyright (C) 2003-2004 MontaVista Software, Inc.
- */
-
-#ifndef _ARCH_UNCOMPRESS_H_
-#define _ARCH_UNCOMPRESS_H_
-
-#include "ixp4xx-regs.h"
-#include <asm/mach-types.h>
-#include <linux/serial_reg.h>
-
-#define TX_DONE (UART_LSR_TEMT|UART_LSR_THRE)
-
-volatile u32* uart_base;
-
-static inline void putc(int c)
-{
-	/* Check THRE and TEMT bits before we transmit the character.
-	 */
-	while ((uart_base[UART_LSR] & TX_DONE) != TX_DONE)
-		barrier();
-
-	*uart_base = c;
-}
-
-static void flush(void)
-{
-}
-
-static __inline__ void __arch_decomp_setup(unsigned long arch_id)
-{
-	/*
-	 * Some boards are using UART2 as console
-	 */
-	if (machine_is_adi_coyote() || machine_is_gtwx5715() ||
-	    machine_is_gateway7001() || machine_is_wg302v2() ||
-	    machine_is_devixp() || machine_is_miccpt() || machine_is_mic256())
-		uart_base = (volatile u32*) IXP4XX_UART2_BASE_PHYS;
-	else
-		uart_base = (volatile u32*) IXP4XX_UART1_BASE_PHYS;
-}
-
-/*
- * arch_id is a variable in decompress_kernel()
- */
-#define arch_decomp_setup()	__arch_decomp_setup(arch_id)
-
-#endif
diff --git a/arch/arm/mach-ixp4xx/irqs.h b/arch/arm/mach-ixp4xx/irqs.h
deleted file mode 100644
index a3e8d6408c56..000000000000
--- a/arch/arm/mach-ixp4xx/irqs.h
+++ /dev/null
@@ -1,64 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-only */
-/*
- * arch/arm/mach-ixp4xx/include/mach/irqs.h 
- *
- * IRQ definitions for IXP4XX based systems
- *
- * Copyright (C) 2002 Intel Corporation.
- * Copyright (C) 2003 MontaVista Software, Inc.
- */
-
-#ifndef _ARCH_IXP4XX_IRQS_H_
-#define _ARCH_IXP4XX_IRQS_H_
-
-#define IRQ_IXP4XX_BASE		16
-
-#define IRQ_IXP4XX_NPEA		(IRQ_IXP4XX_BASE + 0)
-#define IRQ_IXP4XX_NPEB		(IRQ_IXP4XX_BASE + 1)
-#define IRQ_IXP4XX_NPEC		(IRQ_IXP4XX_BASE + 2)
-#define IRQ_IXP4XX_QM1		(IRQ_IXP4XX_BASE + 3)
-#define IRQ_IXP4XX_QM2		(IRQ_IXP4XX_BASE + 4)
-#define IRQ_IXP4XX_TIMER1	(IRQ_IXP4XX_BASE + 5)
-#define IRQ_IXP4XX_GPIO0	(IRQ_IXP4XX_BASE + 6)
-#define IRQ_IXP4XX_GPIO1	(IRQ_IXP4XX_BASE + 7)
-#define IRQ_IXP4XX_PCI_INT	(IRQ_IXP4XX_BASE + 8)
-#define IRQ_IXP4XX_PCI_DMA1	(IRQ_IXP4XX_BASE + 9)
-#define IRQ_IXP4XX_PCI_DMA2	(IRQ_IXP4XX_BASE + 10)
-#define IRQ_IXP4XX_TIMER2	(IRQ_IXP4XX_BASE + 11)
-#define IRQ_IXP4XX_USB		(IRQ_IXP4XX_BASE + 12)
-#define IRQ_IXP4XX_UART2	(IRQ_IXP4XX_BASE + 13)
-#define IRQ_IXP4XX_TIMESTAMP	(IRQ_IXP4XX_BASE + 14)
-#define IRQ_IXP4XX_UART1	(IRQ_IXP4XX_BASE + 15)
-#define IRQ_IXP4XX_WDOG		(IRQ_IXP4XX_BASE + 16)
-#define IRQ_IXP4XX_AHB_PMU	(IRQ_IXP4XX_BASE + 17)
-#define IRQ_IXP4XX_XSCALE_PMU	(IRQ_IXP4XX_BASE + 18)
-#define IRQ_IXP4XX_GPIO2	(IRQ_IXP4XX_BASE + 19)
-#define IRQ_IXP4XX_GPIO3	(IRQ_IXP4XX_BASE + 20)
-#define IRQ_IXP4XX_GPIO4	(IRQ_IXP4XX_BASE + 21)
-#define IRQ_IXP4XX_GPIO5	(IRQ_IXP4XX_BASE + 22)
-#define IRQ_IXP4XX_GPIO6	(IRQ_IXP4XX_BASE + 23)
-#define IRQ_IXP4XX_GPIO7	(IRQ_IXP4XX_BASE + 24)
-#define IRQ_IXP4XX_GPIO8	(IRQ_IXP4XX_BASE + 25)
-#define IRQ_IXP4XX_GPIO9	(IRQ_IXP4XX_BASE + 26)
-#define IRQ_IXP4XX_GPIO10	(IRQ_IXP4XX_BASE + 27)
-#define IRQ_IXP4XX_GPIO11	(IRQ_IXP4XX_BASE + 28)
-#define IRQ_IXP4XX_GPIO12	(IRQ_IXP4XX_BASE + 29)
-#define IRQ_IXP4XX_SW_INT1	(IRQ_IXP4XX_BASE + 30)
-#define IRQ_IXP4XX_SW_INT2	(IRQ_IXP4XX_BASE + 31)
-#define IRQ_IXP4XX_USB_HOST	(IRQ_IXP4XX_BASE + 32)
-#define IRQ_IXP4XX_I2C		(IRQ_IXP4XX_BASE + 33)
-#define IRQ_IXP4XX_SSP		(IRQ_IXP4XX_BASE + 34)
-#define IRQ_IXP4XX_TSYNC	(IRQ_IXP4XX_BASE + 35)
-#define IRQ_IXP4XX_EAU_DONE	(IRQ_IXP4XX_BASE + 36)
-#define IRQ_IXP4XX_SHA_DONE	(IRQ_IXP4XX_BASE + 37)
-#define IRQ_IXP4XX_SWCP_PE	(IRQ_IXP4XX_BASE + 58)
-#define IRQ_IXP4XX_QM_PE	(IRQ_IXP4XX_BASE + 60)
-#define IRQ_IXP4XX_MCU_ECC	(IRQ_IXP4XX_BASE + 61)
-#define IRQ_IXP4XX_EXP_PE	(IRQ_IXP4XX_BASE + 62)
-
-#define _IXP4XX_GPIO_IRQ(n)	(IRQ_IXP4XX_GPIO ## n)
-#define IXP4XX_GPIO_IRQ(n)	_IXP4XX_GPIO_IRQ(n)
-
-#define	XSCALE_PMU_IRQ		(IRQ_IXP4XX_XSCALE_PMU)
-
-#endif
diff --git a/arch/arm/mach-ixp4xx/ixp4xx-of.c b/arch/arm/mach-ixp4xx/ixp4xx-of.c
index f9904716ec7f..f543e2adae0c 100644
--- a/arch/arm/mach-ixp4xx/ixp4xx-of.c
+++ b/arch/arm/mach-ixp4xx/ixp4xx-of.c
@@ -46,7 +46,7 @@ static void __init ixp4xx_of_map_io(void)
 }
 
 /*
- * We handle 4 differen SoC families. These compatible strings are enough
+ * We handle 4 different SoC families. These compatible strings are enough
  * to provide the core so that different boards can add their more detailed
  * specifics.
  */
diff --git a/arch/arm/mach-keystone/Kconfig b/arch/arm/mach-keystone/Kconfig
index cfd39f729f8e..de69cc2dd483 100644
--- a/arch/arm/mach-keystone/Kconfig
+++ b/arch/arm/mach-keystone/Kconfig
@@ -8,7 +8,6 @@ config ARCH_KEYSTONE
 	select ARCH_HAS_RESET_CONTROLLER
 	select ARM_ERRATA_798181 if SMP
 	select COMMON_CLK_KEYSTONE
-	select ARCH_SUPPORTS_BIG_ENDIAN
 	select ZONE_DMA if ARM_LPAE
 	select PINCTRL
 	select PM_GENERIC_DOMAINS if PM
diff --git a/arch/arm/mach-lpc18xx/Makefile.boot b/arch/arm/mach-lpc18xx/Makefile.boot
deleted file mode 100644
index cec195d4fcba..000000000000
--- a/arch/arm/mach-lpc18xx/Makefile.boot
+++ /dev/null
@@ -1,4 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0-only
-# Empty file waiting for deletion once Makefile.boot isn't needed any more.
-# Patch waits for application at
-# http://www.arm.linux.org.uk/developer/patches/viewpatch.php?id=7889/1 .
diff --git a/arch/arm/mach-lpc18xx/board-dt.c b/arch/arm/mach-lpc18xx/board-dt.c
index fdcee78d1bc4..4729eb83401a 100644
--- a/arch/arm/mach-lpc18xx/board-dt.c
+++ b/arch/arm/mach-lpc18xx/board-dt.c
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Device Tree board file for NXP LPC18xx/43xx
  *
  * Copyright (C) 2015 Joachim Eastwood <manabian@gmail.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #include <asm/mach/arch.h>
diff --git a/arch/arm/mach-lpc32xx/Kconfig b/arch/arm/mach-lpc32xx/Kconfig
index ec87c65f4536..35730d3696d0 100644
--- a/arch/arm/mach-lpc32xx/Kconfig
+++ b/arch/arm/mach-lpc32xx/Kconfig
@@ -3,6 +3,7 @@
 config ARCH_LPC32XX
 	bool "NXP LPC32XX"
 	depends on ARCH_MULTI_V5
+	depends on CPU_LITTLE_ENDIAN
 	select ARM_AMBA
 	select CLKSRC_LPC32XX
 	select CPU_ARM926T
diff --git a/arch/arm/mach-lpc32xx/Makefile.boot b/arch/arm/mach-lpc32xx/Makefile.boot
deleted file mode 100644
index 37d09ddb27f8..000000000000
--- a/arch/arm/mach-lpc32xx/Makefile.boot
+++ /dev/null
@@ -1,4 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0-only
-   zreladdr-y	+= 0x80008000
-params_phys-y	:= 0x80000100
-initrd_phys-y	:= 0x82000000
diff --git a/arch/arm/mach-lpc32xx/pm.c b/arch/arm/mach-lpc32xx/pm.c
index b27fa1b9f56c..2572bd89a5e8 100644
--- a/arch/arm/mach-lpc32xx/pm.c
+++ b/arch/arm/mach-lpc32xx/pm.c
@@ -1,13 +1,11 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/mach-lpc32xx/pm.c
  *
  * Original authors: Vitaly Wool, Dmitry Chigirev <source@mvista.com>
  * Modified by Kevin Wells <kevin.wells@nxp.com>
  *
- * 2005 (c) MontaVista Software, Inc. This file is licensed under
- * the terms of the GNU General Public License version 2. This program
- * is licensed "as is" without any warranty of any kind, whether express
- * or implied.
+ * 2005 (c) MontaVista Software, Inc.
  */
 
 /*
diff --git a/arch/arm/mach-lpc32xx/suspend.S b/arch/arm/mach-lpc32xx/suspend.S
index 3f0a8282ef6f..a95c5e0e4038 100644
--- a/arch/arm/mach-lpc32xx/suspend.S
+++ b/arch/arm/mach-lpc32xx/suspend.S
@@ -1,13 +1,11 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * arch/arm/mach-lpc32xx/suspend.S
  *
  * Original authors: Dmitry Chigirev, Vitaly Wool <source@mvista.com>
  * Modified by Kevin Wells <kevin.wells@nxp.com>
  *
- * 2005 (c) MontaVista Software, Inc. This file is licensed under
- * the terms of the GNU General Public License version 2. This program
- * is licensed "as is" without any warranty of any kind, whether express
- * or implied.
+ * 2005 (c) MontaVista Software, Inc.
  */
 #include <linux/linkage.h>
 #include <asm/assembler.h>
diff --git a/arch/arm/mach-mediatek/Kconfig b/arch/arm/mach-mediatek/Kconfig
index 9e0f592d87d8..35a3430c7942 100644
--- a/arch/arm/mach-mediatek/Kconfig
+++ b/arch/arm/mach-mediatek/Kconfig
@@ -30,6 +30,7 @@ config MACH_MT7623
 config MACH_MT7629
 	bool "MediaTek MT7629 SoCs support"
 	default ARCH_MEDIATEK
+	select HAVE_ARM_ARCH_TIMER
 
 config MACH_MT8127
 	bool "MediaTek MT8127 SoCs support"
diff --git a/arch/arm/mach-meson/platsmp.c b/arch/arm/mach-meson/platsmp.c
index 4b8ad728bb42..32ac60b89fdc 100644
--- a/arch/arm/mach-meson/platsmp.c
+++ b/arch/arm/mach-meson/platsmp.c
@@ -71,6 +71,7 @@ static void __init meson_smp_prepare_cpus(const char *scu_compatible,
 	}
 
 	sram_base = of_iomap(node, 0);
+	of_node_put(node);
 	if (!sram_base) {
 		pr_err("Couldn't map SRAM registers\n");
 		return;
@@ -91,6 +92,7 @@ static void __init meson_smp_prepare_cpus(const char *scu_compatible,
 	}
 
 	scu_base = of_iomap(node, 0);
+	of_node_put(node);
 	if (!scu_base) {
 		pr_err("Couldn't map SCU registers\n");
 		return;
diff --git a/arch/arm/mach-mmp/Kconfig b/arch/arm/mach-mmp/Kconfig
index 0dd999212944..d71417d57961 100644
--- a/arch/arm/mach-mmp/Kconfig
+++ b/arch/arm/mach-mmp/Kconfig
@@ -1,7 +1,7 @@
 # SPDX-License-Identifier: GPL-2.0-only
 menuconfig ARCH_MMP
 	bool "Marvell PXA168/910/MMP2/MMP3"
-	depends on ARCH_MULTI_V5 || ARCH_MULTI_V7
+	depends on (CPU_LITTLE_ENDIAN && ARCH_MULTI_V5) || ARCH_MULTI_V7
 	select GPIO_PXA
 	select GPIOLIB
 	select PINCTRL
@@ -18,6 +18,7 @@ if ATAGS
 config MACH_ASPENITE
 	bool "Marvell's PXA168 Aspenite Development Board"
 	depends on ARCH_MULTI_V5
+	depends on UNUSED_BOARD_FILES
 	select CPU_PXA168
 	help
 	  Say 'Y' here if you want to support the Marvell PXA168-based
@@ -26,6 +27,7 @@ config MACH_ASPENITE
 config MACH_ZYLONITE2
 	bool "Marvell's PXA168 Zylonite2 Development Board"
 	depends on ARCH_MULTI_V5
+	depends on UNUSED_BOARD_FILES
 	select CPU_PXA168
 	help
 	  Say 'Y' here if you want to support the Marvell PXA168-based
@@ -34,22 +36,16 @@ config MACH_ZYLONITE2
 config MACH_AVENGERS_LITE
 	bool "Marvell's PXA168 Avengers Lite Development Board"
 	depends on ARCH_MULTI_V5
+	depends on UNUSED_BOARD_FILES
 	select CPU_PXA168
 	help
 	  Say 'Y' here if you want to support the Marvell PXA168-based
 	  Avengers Lite Development Board.
 
-config MACH_TAVOREVB
-	bool "Marvell's PXA910 TavorEVB Development Board"
-	depends on ARCH_MULTI_V5
-	select CPU_PXA910
-	help
-	  Say 'Y' here if you want to support the Marvell PXA910-based
-	  TavorEVB Development Board.
-
 config MACH_TTC_DKB
-	bool "Marvell's PXA910 TavorEVB Development Board"
+	bool "Marvell's PXA910 TavorEVB/TTC_DKB Development Board"
 	depends on ARCH_MULTI_V5
+	depends on UNUSED_BOARD_FILES
 	select CPU_PXA910
 	help
 	  Say 'Y' here if you want to support the Marvell PXA910-based
@@ -58,6 +54,7 @@ config MACH_TTC_DKB
 config MACH_BROWNSTONE
 	bool "Marvell's Brownstone Development Platform"
 	depends on ARCH_MULTI_V7
+	depends on UNUSED_BOARD_FILES
 	select CPU_MMP2
 	help
 	  Say 'Y' here if you want to support the Marvell MMP2-based
@@ -69,6 +66,7 @@ config MACH_BROWNSTONE
 config MACH_FLINT
 	bool "Marvell's Flint Development Platform"
 	depends on ARCH_MULTI_V7
+	depends on UNUSED_BOARD_FILES
 	select CPU_MMP2
 	help
 	  Say 'Y' here if you want to support the Marvell MMP2-based
@@ -80,6 +78,7 @@ config MACH_FLINT
 config MACH_MARVELL_JASPER
 	bool "Marvell's Jasper Development Platform"
 	depends on ARCH_MULTI_V7
+	depends on UNUSED_BOARD_FILES
 	select CPU_MMP2
 	help
 	  Say 'Y' here if you want to support the Marvell MMP2-base
@@ -91,6 +90,7 @@ config MACH_MARVELL_JASPER
 config MACH_TETON_BGA
 	bool "Marvell's PXA168 Teton BGA Development Board"
 	depends on ARCH_MULTI_V5
+	depends on UNUSED_BOARD_FILES
 	select CPU_PXA168
 	help
 	  Say 'Y' here if you want to support the Marvell PXA168-based
@@ -99,6 +99,7 @@ config MACH_TETON_BGA
 config MACH_GPLUGD
 	bool "Marvell's PXA168 GuruPlug Display (gplugD) Board"
 	depends on ARCH_MULTI_V5
+	depends on UNUSED_BOARD_FILES
 	select CPU_PXA168
 	help
 	  Say 'Y' here if you want to support the Marvell PXA168-based
diff --git a/arch/arm/mach-mmp/Makefile b/arch/arm/mach-mmp/Makefile
index e3758f7e1fe7..539d750aaf10 100644
--- a/arch/arm/mach-mmp/Makefile
+++ b/arch/arm/mach-mmp/Makefile
@@ -2,8 +2,6 @@
 #
 # Makefile for Marvell's PXA168 processors line
 #
-ccflags-$(CONFIG_ARCH_MULTIPLATFORM) := -I$(srctree)/arch/arm/plat-pxa/include
-
 obj-y				+= common.o devices.o time.o
 
 # SoC support
@@ -24,7 +22,6 @@ endif
 obj-$(CONFIG_MACH_ASPENITE)	+= aspenite.o
 obj-$(CONFIG_MACH_ZYLONITE2)	+= aspenite.o
 obj-$(CONFIG_MACH_AVENGERS_LITE)+= avengers_lite.o
-obj-$(CONFIG_MACH_TAVOREVB)	+= tavorevb.o
 obj-$(CONFIG_MACH_TTC_DKB)	+= ttc_dkb.o
 obj-$(CONFIG_MACH_BROWNSTONE)	+= brownstone.o
 obj-$(CONFIG_MACH_FLINT)	+= flint.o
diff --git a/arch/arm/mach-mmp/devices.c b/arch/arm/mach-mmp/devices.c
index 18bee66a671f..9968239d8041 100644
--- a/arch/arm/mach-mmp/devices.c
+++ b/arch/arm/mach-mmp/devices.c
@@ -14,7 +14,7 @@
 #include <linux/soc/mmp/cputype.h>
 #include "regs-usb.h"
 
-int __init pxa_register_device(struct pxa_device_desc *desc,
+int __init mmp_register_device(struct mmp_device_desc *desc,
 				void *data, size_t size)
 {
 	struct platform_device *pdev;
@@ -238,7 +238,7 @@ void pxa_usb_phy_deinit(void __iomem *phy_reg)
 static u64 __maybe_unused usb_dma_mask = ~(u32)0;
 
 #if IS_ENABLED(CONFIG_PHY_PXA_USB)
-struct resource pxa168_usb_phy_resources[] = {
+static struct resource pxa168_usb_phy_resources[] = {
 	[0] = {
 		.start	= PXA168_U2O_PHYBASE,
 		.end	= PXA168_U2O_PHYBASE + USB_PHY_RANGE,
@@ -259,7 +259,7 @@ struct platform_device pxa168_device_usb_phy = {
 #endif /* CONFIG_PHY_PXA_USB */
 
 #if IS_ENABLED(CONFIG_USB_MV_UDC)
-struct resource pxa168_u2o_resources[] = {
+static struct resource pxa168_u2o_resources[] = {
 	/* regbase */
 	[0] = {
 		.start	= PXA168_U2O_REGBASE + U2x_CAPREGS_OFFSET,
@@ -294,7 +294,7 @@ struct platform_device pxa168_device_u2o = {
 #endif /* CONFIG_USB_MV_UDC */
 
 #if IS_ENABLED(CONFIG_USB_EHCI_MV_U2O)
-struct resource pxa168_u2oehci_resources[] = {
+static struct resource pxa168_u2oehci_resources[] = {
 	[0] = {
 		.start	= PXA168_U2O_REGBASE,
 		.end	= PXA168_U2O_REGBASE + USB_REG_RANGE,
@@ -321,7 +321,7 @@ struct platform_device pxa168_device_u2oehci = {
 #endif
 
 #if IS_ENABLED(CONFIG_USB_MV_OTG)
-struct resource pxa168_u2ootg_resources[] = {
+static struct resource pxa168_u2ootg_resources[] = {
 	/* regbase */
 	[0] = {
 		.start	= PXA168_U2O_REGBASE + U2x_CAPREGS_OFFSET,
diff --git a/arch/arm/mach-mmp/devices.h b/arch/arm/mach-mmp/devices.h
index 4df596c5c201..d4920ebfebc5 100644
--- a/arch/arm/mach-mmp/devices.h
+++ b/arch/arm/mach-mmp/devices.h
@@ -7,7 +7,7 @@
 #define MAX_RESOURCE_DMA	2
 
 /* structure for describing the on-chip devices */
-struct pxa_device_desc {
+struct mmp_device_desc {
 	const char	*dev_name;
 	const char	*drv_name;
 	int		id;
@@ -18,7 +18,7 @@ struct pxa_device_desc {
 };
 
 #define PXA168_DEVICE(_name, _drv, _id, _irq, _start, _size, _dma...)	\
-struct pxa_device_desc pxa168_device_##_name __initdata = {		\
+struct mmp_device_desc pxa168_device_##_name __initdata = {		\
 	.dev_name	= "pxa168-" #_name,				\
 	.drv_name	= _drv,						\
 	.id		= _id,						\
@@ -29,7 +29,7 @@ struct pxa_device_desc pxa168_device_##_name __initdata = {		\
 };
 
 #define PXA910_DEVICE(_name, _drv, _id, _irq, _start, _size, _dma...)	\
-struct pxa_device_desc pxa910_device_##_name __initdata = {		\
+struct mmp_device_desc pxa910_device_##_name __initdata = {		\
 	.dev_name	= "pxa910-" #_name,				\
 	.drv_name	= _drv,						\
 	.id		= _id,						\
@@ -40,7 +40,7 @@ struct pxa_device_desc pxa910_device_##_name __initdata = {		\
 };
 
 #define MMP2_DEVICE(_name, _drv, _id, _irq, _start, _size, _dma...)	\
-struct pxa_device_desc mmp2_device_##_name __initdata = {		\
+struct mmp_device_desc mmp2_device_##_name __initdata = {		\
 	.dev_name	= "mmp2-" #_name,				\
 	.drv_name	= _drv,						\
 	.id		= _id,						\
@@ -50,7 +50,7 @@ struct pxa_device_desc mmp2_device_##_name __initdata = {		\
 	.dma		= { _dma },					\
 }
 
-extern int pxa_register_device(struct pxa_device_desc *, void *, size_t);
+extern int mmp_register_device(struct mmp_device_desc *, void *, size_t);
 extern int pxa_usb_phy_init(void __iomem *phy_reg);
 extern void pxa_usb_phy_deinit(void __iomem *phy_reg);
 
diff --git a/arch/arm/mach-mmp/mfp.h b/arch/arm/mach-mmp/mfp.h
index 75a4acb33b1b..6f3057987756 100644
--- a/arch/arm/mach-mmp/mfp.h
+++ b/arch/arm/mach-mmp/mfp.h
@@ -2,7 +2,7 @@
 #ifndef __ASM_MACH_MFP_H
 #define __ASM_MACH_MFP_H
 
-#include <plat/mfp.h>
+#include <linux/soc/pxa/mfp.h>
 
 /*
  * NOTE: the MFPR register bit definitions on PXA168 processor lines are a
diff --git a/arch/arm/mach-mmp/mmp2.h b/arch/arm/mach-mmp/mmp2.h
index adafc4fba8f4..7f80b90248fb 100644
--- a/arch/arm/mach-mmp/mmp2.h
+++ b/arch/arm/mach-mmp/mmp2.h
@@ -5,38 +5,38 @@
 #include <linux/platform_data/pxa_sdhci.h>
 
 extern void mmp2_timer_init(void);
-extern void __init mmp2_init_icu(void);
 extern void __init mmp2_init_irq(void);
 extern void mmp2_clear_pmic_int(void);
 
 #include <linux/i2c.h>
 #include <linux/platform_data/i2c-pxa.h>
 #include <linux/platform_data/dma-mmp_tdma.h>
+#include <linux/irqchip/mmp.h>
 
 #include "devices.h"
 
-extern struct pxa_device_desc mmp2_device_uart1;
-extern struct pxa_device_desc mmp2_device_uart2;
-extern struct pxa_device_desc mmp2_device_uart3;
-extern struct pxa_device_desc mmp2_device_uart4;
-extern struct pxa_device_desc mmp2_device_twsi1;
-extern struct pxa_device_desc mmp2_device_twsi2;
-extern struct pxa_device_desc mmp2_device_twsi3;
-extern struct pxa_device_desc mmp2_device_twsi4;
-extern struct pxa_device_desc mmp2_device_twsi5;
-extern struct pxa_device_desc mmp2_device_twsi6;
-extern struct pxa_device_desc mmp2_device_sdh0;
-extern struct pxa_device_desc mmp2_device_sdh1;
-extern struct pxa_device_desc mmp2_device_sdh2;
-extern struct pxa_device_desc mmp2_device_sdh3;
-extern struct pxa_device_desc mmp2_device_asram;
-extern struct pxa_device_desc mmp2_device_isram;
+extern struct mmp_device_desc mmp2_device_uart1;
+extern struct mmp_device_desc mmp2_device_uart2;
+extern struct mmp_device_desc mmp2_device_uart3;
+extern struct mmp_device_desc mmp2_device_uart4;
+extern struct mmp_device_desc mmp2_device_twsi1;
+extern struct mmp_device_desc mmp2_device_twsi2;
+extern struct mmp_device_desc mmp2_device_twsi3;
+extern struct mmp_device_desc mmp2_device_twsi4;
+extern struct mmp_device_desc mmp2_device_twsi5;
+extern struct mmp_device_desc mmp2_device_twsi6;
+extern struct mmp_device_desc mmp2_device_sdh0;
+extern struct mmp_device_desc mmp2_device_sdh1;
+extern struct mmp_device_desc mmp2_device_sdh2;
+extern struct mmp_device_desc mmp2_device_sdh3;
+extern struct mmp_device_desc mmp2_device_asram;
+extern struct mmp_device_desc mmp2_device_isram;
 
 extern struct platform_device mmp2_device_gpio;
 
 static inline int mmp2_add_uart(int id)
 {
-	struct pxa_device_desc *d = NULL;
+	struct mmp_device_desc *d = NULL;
 
 	switch (id) {
 	case 1: d = &mmp2_device_uart1; break;
@@ -47,13 +47,13 @@ static inline int mmp2_add_uart(int id)
 		return -EINVAL;
 	}
 
-	return pxa_register_device(d, NULL, 0);
+	return mmp_register_device(d, NULL, 0);
 }
 
 static inline int mmp2_add_twsi(int id, struct i2c_pxa_platform_data *data,
 				  struct i2c_board_info *info, unsigned size)
 {
-	struct pxa_device_desc *d = NULL;
+	struct mmp_device_desc *d = NULL;
 	int ret;
 
 	switch (id) {
@@ -71,12 +71,12 @@ static inline int mmp2_add_twsi(int id, struct i2c_pxa_platform_data *data,
 	if (ret)
 		return ret;
 
-	return pxa_register_device(d, data, sizeof(*data));
+	return mmp_register_device(d, data, sizeof(*data));
 }
 
 static inline int mmp2_add_sdhost(int id, struct sdhci_pxa_platdata *data)
 {
-	struct pxa_device_desc *d = NULL;
+	struct mmp_device_desc *d = NULL;
 
 	switch (id) {
 	case 0: d = &mmp2_device_sdh0; break;
@@ -87,17 +87,17 @@ static inline int mmp2_add_sdhost(int id, struct sdhci_pxa_platdata *data)
 		return -EINVAL;
 	}
 
-	return pxa_register_device(d, data, sizeof(*data));
+	return mmp_register_device(d, data, sizeof(*data));
 }
 
 static inline int mmp2_add_asram(struct sram_platdata *data)
 {
-	return pxa_register_device(&mmp2_device_asram, data, sizeof(*data));
+	return mmp_register_device(&mmp2_device_asram, data, sizeof(*data));
 }
 
 static inline int mmp2_add_isram(struct sram_platdata *data)
 {
-	return pxa_register_device(&mmp2_device_isram, data, sizeof(*data));
+	return mmp_register_device(&mmp2_device_isram, data, sizeof(*data));
 }
 
 #endif /* __ASM_MACH_MMP2_H */
diff --git a/arch/arm/mach-mmp/pxa168.h b/arch/arm/mach-mmp/pxa168.h
index dff651b9f252..c1547e098f09 100644
--- a/arch/arm/mach-mmp/pxa168.h
+++ b/arch/arm/mach-mmp/pxa168.h
@@ -5,7 +5,6 @@
 #include <linux/reboot.h>
 
 extern void pxa168_timer_init(void);
-extern void __init icu_init_irq(void);
 extern void __init pxa168_init_irq(void);
 extern void pxa168_restart(enum reboot_mode, const char *);
 extern void pxa168_clear_keypad_wakeup(void);
@@ -18,27 +17,28 @@ extern void pxa168_clear_keypad_wakeup(void);
 #include <linux/pxa168_eth.h>
 #include <linux/platform_data/mv_usb.h>
 #include <linux/soc/mmp/cputype.h>
+#include <linux/irqchip/mmp.h>
 
 #include "devices.h"
 
-extern struct pxa_device_desc pxa168_device_uart1;
-extern struct pxa_device_desc pxa168_device_uart2;
-extern struct pxa_device_desc pxa168_device_uart3;
-extern struct pxa_device_desc pxa168_device_twsi0;
-extern struct pxa_device_desc pxa168_device_twsi1;
-extern struct pxa_device_desc pxa168_device_pwm1;
-extern struct pxa_device_desc pxa168_device_pwm2;
-extern struct pxa_device_desc pxa168_device_pwm3;
-extern struct pxa_device_desc pxa168_device_pwm4;
-extern struct pxa_device_desc pxa168_device_ssp1;
-extern struct pxa_device_desc pxa168_device_ssp2;
-extern struct pxa_device_desc pxa168_device_ssp3;
-extern struct pxa_device_desc pxa168_device_ssp4;
-extern struct pxa_device_desc pxa168_device_ssp5;
-extern struct pxa_device_desc pxa168_device_nand;
-extern struct pxa_device_desc pxa168_device_fb;
-extern struct pxa_device_desc pxa168_device_keypad;
-extern struct pxa_device_desc pxa168_device_eth;
+extern struct mmp_device_desc pxa168_device_uart1;
+extern struct mmp_device_desc pxa168_device_uart2;
+extern struct mmp_device_desc pxa168_device_uart3;
+extern struct mmp_device_desc pxa168_device_twsi0;
+extern struct mmp_device_desc pxa168_device_twsi1;
+extern struct mmp_device_desc pxa168_device_pwm1;
+extern struct mmp_device_desc pxa168_device_pwm2;
+extern struct mmp_device_desc pxa168_device_pwm3;
+extern struct mmp_device_desc pxa168_device_pwm4;
+extern struct mmp_device_desc pxa168_device_ssp1;
+extern struct mmp_device_desc pxa168_device_ssp2;
+extern struct mmp_device_desc pxa168_device_ssp3;
+extern struct mmp_device_desc pxa168_device_ssp4;
+extern struct mmp_device_desc pxa168_device_ssp5;
+extern struct mmp_device_desc pxa168_device_nand;
+extern struct mmp_device_desc pxa168_device_fb;
+extern struct mmp_device_desc pxa168_device_keypad;
+extern struct mmp_device_desc pxa168_device_eth;
 
 /* pdata can be NULL */
 extern int __init pxa168_add_usb_host(struct mv_usb_platform_data *pdata);
@@ -48,7 +48,7 @@ extern struct platform_device pxa168_device_gpio;
 
 static inline int pxa168_add_uart(int id)
 {
-	struct pxa_device_desc *d = NULL;
+	struct mmp_device_desc *d = NULL;
 
 	switch (id) {
 	case 1: d = &pxa168_device_uart1; break;
@@ -59,13 +59,13 @@ static inline int pxa168_add_uart(int id)
 	if (d == NULL)
 		return -EINVAL;
 
-	return pxa_register_device(d, NULL, 0);
+	return mmp_register_device(d, NULL, 0);
 }
 
 static inline int pxa168_add_twsi(int id, struct i2c_pxa_platform_data *data,
 				  struct i2c_board_info *info, unsigned size)
 {
-	struct pxa_device_desc *d = NULL;
+	struct mmp_device_desc *d = NULL;
 	int ret;
 
 	switch (id) {
@@ -79,12 +79,12 @@ static inline int pxa168_add_twsi(int id, struct i2c_pxa_platform_data *data,
 	if (ret)
 		return ret;
 
-	return pxa_register_device(d, data, sizeof(*data));
+	return mmp_register_device(d, data, sizeof(*data));
 }
 
 static inline int pxa168_add_pwm(int id)
 {
-	struct pxa_device_desc *d = NULL;
+	struct mmp_device_desc *d = NULL;
 
 	switch (id) {
 	case 1: d = &pxa168_device_pwm1; break;
@@ -95,12 +95,12 @@ static inline int pxa168_add_pwm(int id)
 		return -EINVAL;
 	}
 
-	return pxa_register_device(d, NULL, 0);
+	return mmp_register_device(d, NULL, 0);
 }
 
 static inline int pxa168_add_ssp(int id)
 {
-	struct pxa_device_desc *d = NULL;
+	struct mmp_device_desc *d = NULL;
 
 	switch (id) {
 	case 1: d = &pxa168_device_ssp1; break;
@@ -111,17 +111,17 @@ static inline int pxa168_add_ssp(int id)
 	default:
 		return -EINVAL;
 	}
-	return pxa_register_device(d, NULL, 0);
+	return mmp_register_device(d, NULL, 0);
 }
 
 static inline int pxa168_add_nand(struct pxa3xx_nand_platform_data *info)
 {
-	return pxa_register_device(&pxa168_device_nand, info, sizeof(*info));
+	return mmp_register_device(&pxa168_device_nand, info, sizeof(*info));
 }
 
 static inline int pxa168_add_fb(struct pxa168fb_mach_info *mi)
 {
-	return pxa_register_device(&pxa168_device_fb, mi, sizeof(*mi));
+	return mmp_register_device(&pxa168_device_fb, mi, sizeof(*mi));
 }
 
 static inline int pxa168_add_keypad(struct pxa27x_keypad_platform_data *data)
@@ -129,11 +129,11 @@ static inline int pxa168_add_keypad(struct pxa27x_keypad_platform_data *data)
 	if (cpu_is_pxa168())
 		data->clear_wakeup_event = pxa168_clear_keypad_wakeup;
 
-	return pxa_register_device(&pxa168_device_keypad, data, sizeof(*data));
+	return mmp_register_device(&pxa168_device_keypad, data, sizeof(*data));
 }
 
 static inline int pxa168_add_eth(struct pxa168_eth_platform_data *data)
 {
-	return pxa_register_device(&pxa168_device_eth, data, sizeof(*data));
+	return mmp_register_device(&pxa168_device_eth, data, sizeof(*data));
 }
 #endif /* __ASM_MACH_PXA168_H */
diff --git a/arch/arm/mach-mmp/pxa910.h b/arch/arm/mach-mmp/pxa910.h
index 2dfe38e4acc1..7d229214065a 100644
--- a/arch/arm/mach-mmp/pxa910.h
+++ b/arch/arm/mach-mmp/pxa910.h
@@ -3,38 +3,38 @@
 #define __ASM_MACH_PXA910_H
 
 extern void pxa910_timer_init(void);
-extern void __init icu_init_irq(void);
 extern void __init pxa910_init_irq(void);
 
 #include <linux/i2c.h>
 #include <linux/platform_data/i2c-pxa.h>
 #include <linux/platform_data/mtd-nand-pxa3xx.h>
 #include <video/mmp_disp.h>
+#include <linux/irqchip/mmp.h>
 
 #include "devices.h"
 
-extern struct pxa_device_desc pxa910_device_uart1;
-extern struct pxa_device_desc pxa910_device_uart2;
-extern struct pxa_device_desc pxa910_device_twsi0;
-extern struct pxa_device_desc pxa910_device_twsi1;
-extern struct pxa_device_desc pxa910_device_pwm1;
-extern struct pxa_device_desc pxa910_device_pwm2;
-extern struct pxa_device_desc pxa910_device_pwm3;
-extern struct pxa_device_desc pxa910_device_pwm4;
-extern struct pxa_device_desc pxa910_device_nand;
+extern struct mmp_device_desc pxa910_device_uart1;
+extern struct mmp_device_desc pxa910_device_uart2;
+extern struct mmp_device_desc pxa910_device_twsi0;
+extern struct mmp_device_desc pxa910_device_twsi1;
+extern struct mmp_device_desc pxa910_device_pwm1;
+extern struct mmp_device_desc pxa910_device_pwm2;
+extern struct mmp_device_desc pxa910_device_pwm3;
+extern struct mmp_device_desc pxa910_device_pwm4;
+extern struct mmp_device_desc pxa910_device_nand;
 extern struct platform_device pxa168_device_usb_phy;
 extern struct platform_device pxa168_device_u2o;
 extern struct platform_device pxa168_device_u2ootg;
 extern struct platform_device pxa168_device_u2oehci;
-extern struct pxa_device_desc pxa910_device_disp;
-extern struct pxa_device_desc pxa910_device_fb;
-extern struct pxa_device_desc pxa910_device_panel;
+extern struct mmp_device_desc pxa910_device_disp;
+extern struct mmp_device_desc pxa910_device_fb;
+extern struct mmp_device_desc pxa910_device_panel;
 extern struct platform_device pxa910_device_gpio;
 extern struct platform_device pxa910_device_rtc;
 
 static inline int pxa910_add_uart(int id)
 {
-	struct pxa_device_desc *d = NULL;
+	struct mmp_device_desc *d = NULL;
 
 	switch (id) {
 	case 1: d = &pxa910_device_uart1; break;
@@ -44,13 +44,13 @@ static inline int pxa910_add_uart(int id)
 	if (d == NULL)
 		return -EINVAL;
 
-	return pxa_register_device(d, NULL, 0);
+	return mmp_register_device(d, NULL, 0);
 }
 
 static inline int pxa910_add_twsi(int id, struct i2c_pxa_platform_data *data,
 				  struct i2c_board_info *info, unsigned size)
 {
-	struct pxa_device_desc *d = NULL;
+	struct mmp_device_desc *d = NULL;
 	int ret;
 
 	switch (id) {
@@ -64,12 +64,12 @@ static inline int pxa910_add_twsi(int id, struct i2c_pxa_platform_data *data,
 	if (ret)
 		return ret;
 
-	return pxa_register_device(d, data, sizeof(*data));
+	return mmp_register_device(d, data, sizeof(*data));
 }
 
 static inline int pxa910_add_pwm(int id)
 {
-	struct pxa_device_desc *d = NULL;
+	struct mmp_device_desc *d = NULL;
 
 	switch (id) {
 	case 1: d = &pxa910_device_pwm1; break;
@@ -80,11 +80,11 @@ static inline int pxa910_add_pwm(int id)
 		return -EINVAL;
 	}
 
-	return pxa_register_device(d, NULL, 0);
+	return mmp_register_device(d, NULL, 0);
 }
 
 static inline int pxa910_add_nand(struct pxa3xx_nand_platform_data *info)
 {
-	return pxa_register_device(&pxa910_device_nand, info, sizeof(*info));
+	return mmp_register_device(&pxa910_device_nand, info, sizeof(*info));
 }
 #endif /* __ASM_MACH_PXA910_H */
diff --git a/arch/arm/mach-mmp/sram.c b/arch/arm/mach-mmp/sram.c
index 6794e2db1ad5..ecc46c31004f 100644
--- a/arch/arm/mach-mmp/sram.c
+++ b/arch/arm/mach-mmp/sram.c
@@ -72,6 +72,8 @@ static int sram_probe(struct platform_device *pdev)
 	if (!info)
 		return -ENOMEM;
 
+	platform_set_drvdata(pdev, info);
+
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	if (res == NULL) {
 		dev_err(&pdev->dev, "no memory resource defined\n");
@@ -107,8 +109,6 @@ static int sram_probe(struct platform_device *pdev)
 	list_add(&info->node, &sram_bank_list);
 	mutex_unlock(&sram_lock);
 
-	platform_set_drvdata(pdev, info);
-
 	dev_info(&pdev->dev, "initialized\n");
 	return 0;
 
@@ -127,17 +127,19 @@ static int sram_remove(struct platform_device *pdev)
 	struct sram_bank_info *info;
 
 	info = platform_get_drvdata(pdev);
-	if (info == NULL)
-		return -ENODEV;
 
-	mutex_lock(&sram_lock);
-	list_del(&info->node);
-	mutex_unlock(&sram_lock);
+	if (info->sram_size) {
+		mutex_lock(&sram_lock);
+		list_del(&info->node);
+		mutex_unlock(&sram_lock);
+
+		gen_pool_destroy(info->gpool);
+		iounmap(info->sram_virt);
+		kfree(info->pool_name);
+	}
 
-	gen_pool_destroy(info->gpool);
-	iounmap(info->sram_virt);
-	kfree(info->pool_name);
 	kfree(info);
+
 	return 0;
 }
 
diff --git a/arch/arm/mach-mmp/tavorevb.c b/arch/arm/mach-mmp/tavorevb.c
deleted file mode 100644
index 3261d2322198..000000000000
--- a/arch/arm/mach-mmp/tavorevb.c
+++ /dev/null
@@ -1,113 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- *  linux/arch/arm/mach-mmp/tavorevb.c
- *
- *  Support for the Marvell PXA910-based TavorEVB Development Platform.
- */
-#include <linux/gpio.h>
-#include <linux/gpio-pxa.h>
-#include <linux/init.h>
-#include <linux/kernel.h>
-#include <linux/platform_device.h>
-#include <linux/smc91x.h>
-
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include "addr-map.h"
-#include "mfp-pxa910.h"
-#include "pxa910.h"
-#include "irqs.h"
-
-#include "common.h"
-
-static unsigned long tavorevb_pin_config[] __initdata = {
-	/* UART2 */
-	GPIO47_UART2_RXD,
-	GPIO48_UART2_TXD,
-
-	/* SMC */
-	SM_nCS0_nCS0,
-	SM_ADV_SM_ADV,
-	SM_SCLK_SM_SCLK,
-	SM_SCLK_SM_SCLK,
-	SM_BE0_SM_BE0,
-	SM_BE1_SM_BE1,
-
-	/* DFI */
-	DF_IO0_ND_IO0,
-	DF_IO1_ND_IO1,
-	DF_IO2_ND_IO2,
-	DF_IO3_ND_IO3,
-	DF_IO4_ND_IO4,
-	DF_IO5_ND_IO5,
-	DF_IO6_ND_IO6,
-	DF_IO7_ND_IO7,
-	DF_IO8_ND_IO8,
-	DF_IO9_ND_IO9,
-	DF_IO10_ND_IO10,
-	DF_IO11_ND_IO11,
-	DF_IO12_ND_IO12,
-	DF_IO13_ND_IO13,
-	DF_IO14_ND_IO14,
-	DF_IO15_ND_IO15,
-	DF_nCS0_SM_nCS2_nCS0,
-	DF_ALE_SM_WEn_ND_ALE,
-	DF_CLE_SM_OEn_ND_CLE,
-	DF_WEn_DF_WEn,
-	DF_REn_DF_REn,
-	DF_RDY0_DF_RDY0,
-};
-
-static struct pxa_gpio_platform_data pxa910_gpio_pdata = {
-	.irq_base	= MMP_GPIO_TO_IRQ(0),
-};
-
-static struct smc91x_platdata tavorevb_smc91x_info = {
-	.flags	= SMC91X_USE_16BIT | SMC91X_NOWAIT,
-};
-
-static struct resource smc91x_resources[] = {
-	[0] = {
-		.start	= SMC_CS1_PHYS_BASE + 0x300,
-		.end	= SMC_CS1_PHYS_BASE + 0xfffff,
-		.flags	= IORESOURCE_MEM,
-	},
-	[1] = {
-		.start	= MMP_GPIO_TO_IRQ(80),
-		.end	= MMP_GPIO_TO_IRQ(80),
-		.flags	= IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE,
-	}
-};
-
-static struct platform_device smc91x_device = {
-	.name		= "smc91x",
-	.id		= 0,
-	.dev		= {
-		.platform_data = &tavorevb_smc91x_info,
-	},
-	.num_resources	= ARRAY_SIZE(smc91x_resources),
-	.resource	= smc91x_resources,
-};
-
-static void __init tavorevb_init(void)
-{
-	mfp_config(ARRAY_AND_SIZE(tavorevb_pin_config));
-
-	/* on-chip devices */
-	pxa910_add_uart(1);
-	platform_device_add_data(&pxa910_device_gpio, &pxa910_gpio_pdata,
-				 sizeof(struct pxa_gpio_platform_data));
-	platform_device_register(&pxa910_device_gpio);
-
-	/* off-chip devices */
-	platform_device_register(&smc91x_device);
-}
-
-MACHINE_START(TAVOREVB, "PXA910 Evaluation Board (aka TavorEVB)")
-	.map_io		= mmp_map_io,
-	.nr_irqs	= MMP_NR_IRQS,
-	.init_irq       = pxa910_init_irq,
-	.init_time	= pxa910_timer_init,
-	.init_machine   = tavorevb_init,
-	.restart	= mmp_restart,
-MACHINE_END
diff --git a/arch/arm/mach-mmp/ttc_dkb.c b/arch/arm/mach-mmp/ttc_dkb.c
index 4f240760d4aa..345b2e6d5c7e 100644
--- a/arch/arm/mach-mmp/ttc_dkb.c
+++ b/arch/arm/mach-mmp/ttc_dkb.c
@@ -253,12 +253,12 @@ static struct spi_board_info spi_board_info[] __initdata = {
 
 static void __init add_disp(void)
 {
-	pxa_register_device(&pxa910_device_disp,
+	mmp_register_device(&pxa910_device_disp,
 		&dkb_disp_info, sizeof(dkb_disp_info));
 	spi_register_board_info(spi_board_info, ARRAY_SIZE(spi_board_info));
-	pxa_register_device(&pxa910_device_fb,
+	mmp_register_device(&pxa910_device_fb,
 		&dkb_fb_info, sizeof(dkb_fb_info));
-	pxa_register_device(&pxa910_device_panel,
+	mmp_register_device(&pxa910_device_panel,
 		&dkb_tpo_panel_info, sizeof(dkb_tpo_panel_info));
 }
 #endif
diff --git a/arch/arm/mach-moxart/Kconfig b/arch/arm/mach-moxart/Kconfig
index 31ada63ba51b..909c6573ba8b 100644
--- a/arch/arm/mach-moxart/Kconfig
+++ b/arch/arm/mach-moxart/Kconfig
@@ -2,6 +2,7 @@
 menuconfig ARCH_MOXART
 	bool "MOXA ART SoC"
 	depends on ARCH_MULTI_V4
+	depends on CPU_LITTLE_ENDIAN
 	select CPU_FA526
 	select ARM_DMA_MEM_BUFFERABLE
 	select FARADAY_FTINTC010
diff --git a/arch/arm/mach-mstar/Kconfig b/arch/arm/mach-mstar/Kconfig
index cd300eeedc20..5dbea7b485af 100644
--- a/arch/arm/mach-mstar/Kconfig
+++ b/arch/arm/mach-mstar/Kconfig
@@ -1,8 +1,10 @@
 menuconfig ARCH_MSTARV7
 	bool "MStar/Sigmastar Armv7 SoC Support"
 	depends on ARCH_MULTI_V7
+	select ARM_ERRATA_814220
 	select ARM_GIC
 	select ARM_HEAVY_MB
+	select HAVE_ARM_ARCH_TIMER
 	select MST_IRQ
 	select MSTAR_MSC313_MPLL
 	help
diff --git a/arch/arm/mach-mv78xx0/Kconfig b/arch/arm/mach-mv78xx0/Kconfig
index ea52c7fabb79..da92f94494cc 100644
--- a/arch/arm/mach-mv78xx0/Kconfig
+++ b/arch/arm/mach-mv78xx0/Kconfig
@@ -2,6 +2,8 @@
 menuconfig ARCH_MV78XX0
 	bool "Marvell MV78xx0"
 	depends on ARCH_MULTI_V5
+	depends on CPU_LITTLE_ENDIAN
+	depends on ATAGS && UNUSED_BOARD_FILES
 	select CPU_FEROCEON
 	select GPIOLIB
 	select MVEBU_MBUS
diff --git a/arch/arm/mach-mv78xx0/Makefile b/arch/arm/mach-mv78xx0/Makefile
index a839e960b8c6..50aff70065f2 100644
--- a/arch/arm/mach-mv78xx0/Makefile
+++ b/arch/arm/mach-mv78xx0/Makefile
@@ -1,5 +1,5 @@
 # SPDX-License-Identifier: GPL-2.0
-ccflags-$(CONFIG_ARCH_MULTIPLATFORM) := -I$(srctree)/arch/arm/plat-orion/include
+ccflags-y := -I$(srctree)/arch/arm/plat-orion/include
 
 obj-y				+= common.o mpp.o irq.o pcie.o
 obj-$(CONFIG_MACH_DB78X00_BP)	+= db78x00-bp-setup.o
diff --git a/arch/arm/mach-mv78xx0/bridge-regs.h b/arch/arm/mach-mv78xx0/bridge-regs.h
index 2f54e1753d45..d57ac967c4b3 100644
--- a/arch/arm/mach-mv78xx0/bridge-regs.h
+++ b/arch/arm/mach-mv78xx0/bridge-regs.h
@@ -1,8 +1,4 @@
-/*
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
+/* SPDX-License-Identifier: GPL-2.0-only */
 
 #ifndef __ASM_ARCH_BRIDGE_REGS_H
 #define __ASM_ARCH_BRIDGE_REGS_H
diff --git a/arch/arm/mach-mv78xx0/buffalo-wxl-setup.c b/arch/arm/mach-mv78xx0/buffalo-wxl-setup.c
index e112f2e7cc9a..9aa765d4cdc8 100644
--- a/arch/arm/mach-mv78xx0/buffalo-wxl-setup.c
+++ b/arch/arm/mach-mv78xx0/buffalo-wxl-setup.c
@@ -1,13 +1,10 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/mach-mv78xx0/buffalo-wxl-setup.c
  *
  * Buffalo WXL (Terastation Duo) Setup routines
  *
  * sebastien requiem <sebastien@requiem.fr>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #include <linux/kernel.h>
diff --git a/arch/arm/mach-mv78xx0/common.c b/arch/arm/mach-mv78xx0/common.c
index dd762d1b083f..461a68945c26 100644
--- a/arch/arm/mach-mv78xx0/common.c
+++ b/arch/arm/mach-mv78xx0/common.c
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/mach-mv78xx0/common.c
  *
  * Core functions for Marvell MV78xx0 SoCs
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #include <linux/kernel.h>
diff --git a/arch/arm/mach-mv78xx0/common.h b/arch/arm/mach-mv78xx0/common.h
index 6889af26077d..d8c6c2400e27 100644
--- a/arch/arm/mach-mv78xx0/common.h
+++ b/arch/arm/mach-mv78xx0/common.h
@@ -1,11 +1,8 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * arch/arm/mach-mv78xx0/common.h
  *
  * Core functions for Marvell MV78xx0 SoCs
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #ifndef __ARCH_MV78XX0_COMMON_H
diff --git a/arch/arm/mach-mv78xx0/db78x00-bp-setup.c b/arch/arm/mach-mv78xx0/db78x00-bp-setup.c
index cf16e08d4cf5..da633a33a0c1 100644
--- a/arch/arm/mach-mv78xx0/db78x00-bp-setup.c
+++ b/arch/arm/mach-mv78xx0/db78x00-bp-setup.c
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/mach-mv78xx0/db78x00-bp-setup.c
  *
  * Marvell DB-78x00-BP Development Board Setup
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #include <linux/kernel.h>
diff --git a/arch/arm/mach-mv78xx0/irq.c b/arch/arm/mach-mv78xx0/irq.c
index 788569e960e1..a34b6855fb19 100644
--- a/arch/arm/mach-mv78xx0/irq.c
+++ b/arch/arm/mach-mv78xx0/irq.c
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/mach-mv78xx0/irq.c
  *
  * MV78xx0 IRQ handling.
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 #include <linux/gpio.h>
 #include <linux/kernel.h>
@@ -67,7 +64,6 @@ void __init mv78xx0_init_irq(void)
 	 * registers for core #1 are at an offset of 0x18 from those of
 	 * core #0.)
 	 */
-	orion_gpio_init(NULL, 0, 32, GPIO_VIRT_BASE,
-			mv78xx0_core_index() ? 0x18 : 0,
+	orion_gpio_init(0, 32, GPIO_VIRT_BASE, mv78xx0_core_index() ? 0x18 : 0,
 			IRQ_MV78XX0_GPIO_START, gpio0_irqs);
 }
diff --git a/arch/arm/mach-mv78xx0/irqs.h b/arch/arm/mach-mv78xx0/irqs.h
index 67e0fe730a13..12b357d383d8 100644
--- a/arch/arm/mach-mv78xx0/irqs.h
+++ b/arch/arm/mach-mv78xx0/irqs.h
@@ -1,10 +1,5 @@
-/*
- * IRQ definitions for Marvell MV78xx0 SoCs
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
+/* SPDX-License-Identifier: GPL-2.0-only */
+/* IRQ definitions for Marvell MV78xx0 SoCs */
 
 #ifndef __ASM_ARCH_IRQS_H
 #define __ASM_ARCH_IRQS_H
diff --git a/arch/arm/mach-mv78xx0/mpp.c b/arch/arm/mach-mv78xx0/mpp.c
index 72843c02e95a..aff0e612cbba 100644
--- a/arch/arm/mach-mv78xx0/mpp.c
+++ b/arch/arm/mach-mv78xx0/mpp.c
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/mach-mv78x00/mpp.c
  *
  * MPP functions for Marvell MV78x00 SoCs
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 #include <linux/gpio.h>
 #include <linux/kernel.h>
diff --git a/arch/arm/mach-mv78xx0/mpp.h b/arch/arm/mach-mv78xx0/mpp.h
index 3752302ae2ee..47db52f45546 100644
--- a/arch/arm/mach-mv78xx0/mpp.h
+++ b/arch/arm/mach-mv78xx0/mpp.h
@@ -1,12 +1,8 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * linux/arch/arm/mach-mv78xx0/mpp.h -- Multi Purpose Pins
  *
- *
  * sebastien requiem <sebastien@requiem.fr>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #ifndef __MV78X00_MPP_H
diff --git a/arch/arm/mach-mv78xx0/mv78xx0.h b/arch/arm/mach-mv78xx0/mv78xx0.h
index c1a9a1d1b295..3f19bef7d7ac 100644
--- a/arch/arm/mach-mv78xx0/mv78xx0.h
+++ b/arch/arm/mach-mv78xx0/mv78xx0.h
@@ -1,10 +1,7 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * Generic definitions for Marvell MV78xx0 SoC flavors:
  *  MV781x0 and MV782x0.
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #ifndef __ASM_ARCH_MV78XX0_H
diff --git a/arch/arm/mach-mv78xx0/pcie.c b/arch/arm/mach-mv78xx0/pcie.c
index 636d84b40466..6190f538a124 100644
--- a/arch/arm/mach-mv78xx0/pcie.c
+++ b/arch/arm/mach-mv78xx0/pcie.c
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/mach-mv78xx0/pcie.c
  *
  * PCIe functions for Marvell MV78xx0 SoCs
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #include <linux/kernel.h>
@@ -101,6 +98,7 @@ static void __init mv78xx0_pcie_preinit(void)
 static int __init mv78xx0_pcie_setup(int nr, struct pci_sys_data *sys)
 {
 	struct pcie_port *pp;
+	struct resource realio;
 
 	if (nr >= num_pcie_ports)
 		return 0;
@@ -115,7 +113,9 @@ static int __init mv78xx0_pcie_setup(int nr, struct pci_sys_data *sys)
 	orion_pcie_set_local_bus_nr(pp->base, sys->busnr);
 	orion_pcie_setup(pp->base);
 
-	pci_ioremap_io(nr * SZ_64K, MV78XX0_PCIE_IO_PHYS_BASE(nr));
+	realio.start = nr * SZ_64K;
+	realio.end = realio.start + SZ_64K - 1;
+	pci_remap_iospace(&realio, MV78XX0_PCIE_IO_PHYS_BASE(nr));
 
 	pci_add_resource_offset(&sys->resources, &pp->res, sys->mem_offset);
 
@@ -177,14 +177,19 @@ static struct pci_ops pcie_ops = {
 	.write = pcie_wr_conf,
 };
 
+/*
+ * The root complex has a hardwired class of PCI_CLASS_MEMORY_OTHER, when it
+ * is operating as a root complex this needs to be switched to
+ * PCI_CLASS_BRIDGE_HOST or Linux will errantly try to process the BAR's on
+ * the device. Decoding setup is handled by the orion code.
+ */
 static void rc_pci_fixup(struct pci_dev *dev)
 {
-	/*
-	 * Prevent enumeration of root complex.
-	 */
 	if (dev->bus->parent == NULL && dev->devfn == 0) {
 		int i;
 
+		dev->class &= 0xff;
+		dev->class |= PCI_CLASS_BRIDGE_HOST << 8;
 		for (i = 0; i < DEVICE_COUNT_RESOURCE; i++) {
 			dev->resource[i].start = 0;
 			dev->resource[i].end   = 0;
diff --git a/arch/arm/mach-mv78xx0/rd78x00-masa-setup.c b/arch/arm/mach-mv78xx0/rd78x00-masa-setup.c
index 308ab71ec822..80ca8b1a81de 100644
--- a/arch/arm/mach-mv78xx0/rd78x00-masa-setup.c
+++ b/arch/arm/mach-mv78xx0/rd78x00-masa-setup.c
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/mach-mv78x00/rd78x00-masa-setup.c
  *
  * Marvell RD-78x00-mASA Development Board Setup
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #include <linux/kernel.h>
diff --git a/arch/arm/mach-mvebu/Kconfig b/arch/arm/mach-mvebu/Kconfig
index 34dbeaab94b0..9f60a6fe0eaf 100644
--- a/arch/arm/mach-mvebu/Kconfig
+++ b/arch/arm/mach-mvebu/Kconfig
@@ -1,8 +1,7 @@
 # SPDX-License-Identifier: GPL-2.0-only
 menuconfig ARCH_MVEBU
 	bool "Marvell Engineering Business Unit (MVEBU) SoCs"
-	depends on ARCH_MULTI_V7 || ARCH_MULTI_V5
-	select ARCH_SUPPORTS_BIG_ENDIAN
+	depends on ARCH_MULTI_V7 || (ARCH_MULTI_V5 && CPU_LITTLE_ENDIAN)
 	select CLKSRC_MMIO
 	select PINCTRL
 	select PLAT_ORION
diff --git a/arch/arm/mach-mvebu/Makefile b/arch/arm/mach-mvebu/Makefile
index cb106899dd7c..c21733cbb4fa 100644
--- a/arch/arm/mach-mvebu/Makefile
+++ b/arch/arm/mach-mvebu/Makefile
@@ -1,5 +1,5 @@
 # SPDX-License-Identifier: GPL-2.0
-ccflags-$(CONFIG_ARCH_MULTIPLATFORM) := -I$(srctree)/arch/arm/plat-orion/include
+ccflags-y := -I$(srctree)/arch/arm/plat-orion/include
 
 AFLAGS_coherency_ll.o		:= -Wa,-march=armv7-a
 CFLAGS_pmsu.o			:= -march=armv7-a
diff --git a/arch/arm/mach-mvebu/armada-370-xp.h b/arch/arm/mach-mvebu/armada-370-xp.h
index 09413b678409..c96ecdafe31f 100644
--- a/arch/arm/mach-mvebu/armada-370-xp.h
+++ b/arch/arm/mach-mvebu/armada-370-xp.h
@@ -1,3 +1,4 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * Generic definitions for Marvell Armada_370_XP SoCs
  *
@@ -6,10 +7,6 @@
  * Lior Amsalem <alior@marvell.com>
  * Gregory CLEMENT <gregory.clement@free-electrons.com>
  * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #ifndef __MACH_ARMADA_370_XP_H
diff --git a/arch/arm/mach-mvebu/board-v7.c b/arch/arm/mach-mvebu/board-v7.c
index d2df5ef9382b..fd5d0c8ff695 100644
--- a/arch/arm/mach-mvebu/board-v7.c
+++ b/arch/arm/mach-mvebu/board-v7.c
@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Device Tree support for Armada 370 and XP platforms.
  *
@@ -6,10 +7,6 @@
  * Lior Amsalem <alior@marvell.com>
  * Gregory CLEMENT <gregory.clement@free-electrons.com>
  * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #include <linux/kernel.h>
diff --git a/arch/arm/mach-mvebu/coherency.c b/arch/arm/mach-mvebu/coherency.c
index 49e3c8d20c2f..a6b621ff0b87 100644
--- a/arch/arm/mach-mvebu/coherency.c
+++ b/arch/arm/mach-mvebu/coherency.c
@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Coherency fabric (Aurora) support for Armada 370, 375, 38x and XP
  * platforms.
@@ -8,10 +9,6 @@
  * Gregory Clement <gregory.clement@free-electrons.com>
  * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
  *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- *
  * The Armada 370, 375, 38x and XP SOCs have a coherency fabric which is
  * responsible for ensuring hardware coherency between all CPUs and between
  * CPUs and I/O masters. This file initializes the coherency fabric and
@@ -98,7 +95,7 @@ static int mvebu_hwcc_notifier(struct notifier_block *nb,
 
 	if (event != BUS_NOTIFY_ADD_DEVICE)
 		return NOTIFY_DONE;
-	set_dma_ops(dev, &arm_coherent_dma_ops);
+	dev->dma_coherent = true;
 
 	return NOTIFY_OK;
 }
diff --git a/arch/arm/mach-mvebu/coherency.h b/arch/arm/mach-mvebu/coherency.h
index 6067f14263f7..cae866ab4867 100644
--- a/arch/arm/mach-mvebu/coherency.h
+++ b/arch/arm/mach-mvebu/coherency.h
@@ -1,14 +1,10 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * arch/arm/mach-mvebu/include/mach/coherency.h
  *
- *
  * Coherency fabric (Aurora) support for Armada 370 and XP platforms.
  *
  * Copyright (C) 2012 Marvell
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #ifndef __MACH_370_XP_COHERENCY_H
diff --git a/arch/arm/mach-mvebu/coherency_ll.S b/arch/arm/mach-mvebu/coherency_ll.S
index a3a64bf97250..eb81656e32d4 100644
--- a/arch/arm/mach-mvebu/coherency_ll.S
+++ b/arch/arm/mach-mvebu/coherency_ll.S
@@ -1,3 +1,4 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * Coherency fabric: low level functions
  *
@@ -5,10 +6,6 @@
  *
  * Gregory CLEMENT <gregory.clement@free-electrons.com>
  *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- *
  * This file implements the assembly function to add a CPU to the
  * coherency fabric. This function is called by each of the secondary
  * CPUs during their early boot in an SMP kernel, this why this
diff --git a/arch/arm/mach-mvebu/common.h b/arch/arm/mach-mvebu/common.h
index 6b775492cfad..fbfa3c4f30df 100644
--- a/arch/arm/mach-mvebu/common.h
+++ b/arch/arm/mach-mvebu/common.h
@@ -1,3 +1,4 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * Core functions for Marvell System On Chip
  *
@@ -6,10 +7,6 @@
  * Lior Amsalem <alior@marvell.com>
  * Gregory CLEMENT <gregory.clement@free-electrons.com>
  * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #ifndef __ARCH_MVEBU_COMMON_H
diff --git a/arch/arm/mach-mvebu/cpu-reset.c b/arch/arm/mach-mvebu/cpu-reset.c
index f33a31c6aff8..66b6c0c6ce1d 100644
--- a/arch/arm/mach-mvebu/cpu-reset.c
+++ b/arch/arm/mach-mvebu/cpu-reset.c
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Copyright (C) 2014 Marvell
  *
  * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #define pr_fmt(fmt) "mvebu-cpureset: " fmt
diff --git a/arch/arm/mach-mvebu/dove.c b/arch/arm/mach-mvebu/dove.c
index d076c5771adc..c938ba725d3e 100644
--- a/arch/arm/mach-mvebu/dove.c
+++ b/arch/arm/mach-mvebu/dove.c
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/mach-mvebu/dove.c
  *
  * Marvell Dove 88AP510 System On Chip FDT Board
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #include <linux/init.h>
diff --git a/arch/arm/mach-mvebu/headsmp-a9.S b/arch/arm/mach-mvebu/headsmp-a9.S
index b093a196e801..df723cf85cae 100644
--- a/arch/arm/mach-mvebu/headsmp-a9.S
+++ b/arch/arm/mach-mvebu/headsmp-a9.S
@@ -1,3 +1,4 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * SMP support: Entry point for secondary CPUs of Marvell EBU
  * Cortex-A9 based SOCs (Armada 375 and Armada 38x).
@@ -6,10 +7,6 @@
  *
  * Gregory CLEMENT <gregory.clement@free-electrons.com>
  * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #include <linux/linkage.h>
diff --git a/arch/arm/mach-mvebu/headsmp.S b/arch/arm/mach-mvebu/headsmp.S
index 2c4032e368ba..f05c59dad32a 100644
--- a/arch/arm/mach-mvebu/headsmp.S
+++ b/arch/arm/mach-mvebu/headsmp.S
@@ -1,3 +1,4 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * SMP support: Entry point for secondary CPUs
  *
@@ -7,10 +8,6 @@
  * Gregory CLEMENT <gregory.clement@free-electrons.com>
  * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
  *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- *
  * This file implements the assembly entry point for secondary CPUs in
  * an SMP kernel. The only thing we need to do is to add the CPU to
  * the coherency fabric by writing to 2 registers. Currently the base
diff --git a/arch/arm/mach-mvebu/kirkwood.c b/arch/arm/mach-mvebu/kirkwood.c
index 06b1706595f4..8ff34753e760 100644
--- a/arch/arm/mach-mvebu/kirkwood.c
+++ b/arch/arm/mach-mvebu/kirkwood.c
@@ -1,13 +1,10 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Copyright 2012 (C), Jason Cooper <jason@lakedaemon.net>
  *
  * arch/arm/mach-mvebu/kirkwood.c
  *
  * Flattened Device Tree board initialization
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #include <linux/clk.h>
diff --git a/arch/arm/mach-mvebu/kirkwood.h b/arch/arm/mach-mvebu/kirkwood.h
index 89f3d1f51643..15135994ce2f 100644
--- a/arch/arm/mach-mvebu/kirkwood.h
+++ b/arch/arm/mach-mvebu/kirkwood.h
@@ -1,12 +1,9 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * arch/arm/mach-mvebu/kirkwood.h
  *
  * Generic definitions for Marvell Kirkwood SoC flavors:
  * 88F6180, 88F6192 and 88F6281.
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #define KIRKWOOD_REGS_PHYS_BASE	0xf1000000
diff --git a/arch/arm/mach-mvebu/mvebu-soc-id.c b/arch/arm/mach-mvebu/mvebu-soc-id.c
index a99434bcee84..f436c7b8c7ae 100644
--- a/arch/arm/mach-mvebu/mvebu-soc-id.c
+++ b/arch/arm/mach-mvebu/mvebu-soc-id.c
@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * ID and revision information for mvebu SoCs
  *
@@ -5,10 +6,6 @@
  *
  * Gregory CLEMENT <gregory.clement@free-electrons.com>
  *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- *
  * All the mvebu SoCs have information related to their variant and
  * revision that can be read from the PCI control register. This is
  * done before the PCI initialization to avoid any conflict. Once the
diff --git a/arch/arm/mach-mvebu/mvebu-soc-id.h b/arch/arm/mach-mvebu/mvebu-soc-id.h
index e124a0b82a3e..225649b2288a 100644
--- a/arch/arm/mach-mvebu/mvebu-soc-id.h
+++ b/arch/arm/mach-mvebu/mvebu-soc-id.h
@@ -1,11 +1,8 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * Marvell EBU SoC ID and revision definitions.
  *
  * Copyright (C) 2014 Marvell Semiconductor
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #ifndef __LINUX_MVEBU_SOC_ID_H
diff --git a/arch/arm/mach-mvebu/platsmp-a9.c b/arch/arm/mach-mvebu/platsmp-a9.c
index d715dec1c197..785ee2af5baa 100644
--- a/arch/arm/mach-mvebu/platsmp-a9.c
+++ b/arch/arm/mach-mvebu/platsmp-a9.c
@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Symmetric Multi Processing (SMP) support for Marvell EBU Cortex-A9
  * based SOCs (Armada 375/38x).
@@ -6,10 +7,6 @@
  *
  * Gregory CLEMENT <gregory.clement@free-electrons.com>
  * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #include <linux/init.h>
diff --git a/arch/arm/mach-mvebu/platsmp.c b/arch/arm/mach-mvebu/platsmp.c
index c130497dc6cc..18384ea6862c 100644
--- a/arch/arm/mach-mvebu/platsmp.c
+++ b/arch/arm/mach-mvebu/platsmp.c
@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Symmetric Multi Processing (SMP) support for Armada XP
  *
@@ -8,10 +9,6 @@
  * Gregory CLEMENT <gregory.clement@free-electrons.com>
  * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
  *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- *
  * The Armada XP SoC has 4 ARMv7 PJ4B CPUs running in full HW coherency
  * This file implements the routines for preparing the SMP infrastructure
  * and waking up the secondary CPUs
diff --git a/arch/arm/mach-mvebu/pm-board.c b/arch/arm/mach-mvebu/pm-board.c
index 070552511699..7fa1806acd65 100644
--- a/arch/arm/mach-mvebu/pm-board.c
+++ b/arch/arm/mach-mvebu/pm-board.c
@@ -1,13 +1,10 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Board-level suspend/resume support.
  *
  * Copyright (C) 2014-2015 Marvell
  *
  * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #include <linux/delay.h>
diff --git a/arch/arm/mach-mvebu/pm.c b/arch/arm/mach-mvebu/pm.c
index c487be61d6d8..b149d9b77505 100644
--- a/arch/arm/mach-mvebu/pm.c
+++ b/arch/arm/mach-mvebu/pm.c
@@ -1,13 +1,10 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Suspend/resume support. Currently supporting Armada XP only.
  *
  * Copyright (C) 2014 Marvell
  *
  * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #include <linux/cpu_pm.h>
diff --git a/arch/arm/mach-mvebu/pmsu.c b/arch/arm/mach-mvebu/pmsu.c
index 73d5d72dfc3e..af27a7156675 100644
--- a/arch/arm/mach-mvebu/pmsu.c
+++ b/arch/arm/mach-mvebu/pmsu.c
@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Power Management Service Unit(PMSU) support for Armada 370/XP platforms.
  *
@@ -7,10 +8,6 @@
  * Gregory Clement <gregory.clement@free-electrons.com>
  * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
  *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- *
  * The Armada 370 and Armada XP SOCs have a power management service
  * unit which is responsible for powering down and waking up CPUs and
  * other SOC units
diff --git a/arch/arm/mach-mvebu/pmsu.h b/arch/arm/mach-mvebu/pmsu.h
index ea79269c2702..1e847388e8dd 100644
--- a/arch/arm/mach-mvebu/pmsu.h
+++ b/arch/arm/mach-mvebu/pmsu.h
@@ -1,11 +1,8 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * Power Management Service Unit (PMSU) support for Armada 370/XP platforms.
  *
  * Copyright (C) 2012 Marvell
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #ifndef __MACH_MVEBU_PMSU_H
diff --git a/arch/arm/mach-mvebu/pmsu_ll.S b/arch/arm/mach-mvebu/pmsu_ll.S
index 7aae9a25cfeb..f7d21385fd88 100644
--- a/arch/arm/mach-mvebu/pmsu_ll.S
+++ b/arch/arm/mach-mvebu/pmsu_ll.S
@@ -1,12 +1,9 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * Copyright (C) 2014 Marvell
  *
  * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
  * Gregory Clement <gregory.clement@free-electrons.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #include <linux/linkage.h>
diff --git a/arch/arm/mach-mvebu/system-controller.c b/arch/arm/mach-mvebu/system-controller.c
index 04d9ebe6a90a..48224b6ed6dc 100644
--- a/arch/arm/mach-mvebu/system-controller.c
+++ b/arch/arm/mach-mvebu/system-controller.c
@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * System controller support for Armada 370, 375 and XP platforms.
  *
@@ -7,10 +8,6 @@
  * Gregory CLEMENT <gregory.clement@free-electrons.com>
  * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
  *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- *
  * The Armada 370, 375 and Armada XP SoCs have a range of
  * miscellaneous registers, that do not belong to a particular device,
  * but rather provide system-level features. This basic
diff --git a/arch/arm/mach-mxs/Kconfig b/arch/arm/mach-mxs/Kconfig
index be1c1388055a..26dd8b9b7321 100644
--- a/arch/arm/mach-mxs/Kconfig
+++ b/arch/arm/mach-mxs/Kconfig
@@ -16,6 +16,7 @@ config SOC_IMX28
 config ARCH_MXS
 	bool "Freescale MXS (i.MX23, i.MX28) support"
 	depends on ARCH_MULTI_V5
+	depends on CPU_LITTLE_ENDIAN
 	select GPIOLIB
 	select MXS_TIMER
 	select PINCTRL
diff --git a/arch/arm/mach-nomadik/Kconfig b/arch/arm/mach-nomadik/Kconfig
index e98429be2b18..f5c4df6d2aad 100644
--- a/arch/arm/mach-nomadik/Kconfig
+++ b/arch/arm/mach-nomadik/Kconfig
@@ -2,10 +2,10 @@
 menuconfig ARCH_NOMADIK
 	bool "ST-Ericsson Nomadik"
 	depends on ARCH_MULTI_V5
+	depends on CPU_LITTLE_ENDIAN
 	select ARM_AMBA
 	select ARM_VIC
 	select CLKSRC_NOMADIK_MTU
-	select CLKSRC_NOMADIK_MTU_SCHED_CLOCK
 	select CPU_ARM926T
 	select GPIOLIB
 	select MFD_SYSCON
diff --git a/arch/arm/mach-npcm/Kconfig b/arch/arm/mach-npcm/Kconfig
index a71cf1d189ae..63b42a19d1b8 100644
--- a/arch/arm/mach-npcm/Kconfig
+++ b/arch/arm/mach-npcm/Kconfig
@@ -1,7 +1,7 @@
 # SPDX-License-Identifier: GPL-2.0-only
 menuconfig ARCH_NPCM
 	bool "Nuvoton NPCM Architecture"
-	depends on ARCH_MULTI_V5 || ARCH_MULTI_V7
+	depends on (ARCH_MULTI_V5 && CPU_LITTLE_ENDIAN) || ARCH_MULTI_V7
 	select PINCTRL
 
 if ARCH_NPCM
diff --git a/arch/arm/mach-nspire/Kconfig b/arch/arm/mach-nspire/Kconfig
index b3d161e8e2fb..b7a3871876d7 100644
--- a/arch/arm/mach-nspire/Kconfig
+++ b/arch/arm/mach-nspire/Kconfig
@@ -1,8 +1,8 @@
 # SPDX-License-Identifier: GPL-2.0-only
 config ARCH_NSPIRE
 	bool "TI-NSPIRE based"
-	depends on ARCH_MULTI_V4_V5
-	depends on MMU
+	depends on ARCH_MULTI_V4T
+	depends on CPU_LITTLE_ENDIAN
 	select CPU_ARM926T
 	select GENERIC_IRQ_CHIP
 	select ARM_AMBA
diff --git a/arch/arm/mach-omap1/Kconfig b/arch/arm/mach-omap1/Kconfig
index 208c700c2455..538a960257cc 100644
--- a/arch/arm/mach-omap1/Kconfig
+++ b/arch/arm/mach-omap1/Kconfig
@@ -1,4 +1,17 @@
 # SPDX-License-Identifier: GPL-2.0-only
+menuconfig ARCH_OMAP1
+	bool "TI OMAP1"
+	depends on ARCH_MULTI_V4T || ARCH_MULTI_V5
+	depends on CPU_LITTLE_ENDIAN
+	depends on ATAGS
+	select ARCH_HAS_HOLES_MEMORYMODEL
+	select ARCH_OMAP
+	select CLKSRC_MMIO
+	select FORCE_PCI if PCCARD
+	select GPIOLIB
+	help
+	  Support for older TI OMAP1 (omap7xx, omap15xx or omap16xx)
+
 if ARCH_OMAP1
 
 menu "TI OMAP1 specific features"
@@ -6,28 +19,41 @@ menu "TI OMAP1 specific features"
 comment "OMAP Core Type"
 
 config ARCH_OMAP730
+	depends on ARCH_MULTI_V5
 	bool "OMAP730 Based System"
 	select ARCH_OMAP_OTG
 	select CPU_ARM926T
 	select OMAP_MPU_TIMER
 
 config ARCH_OMAP850
+	depends on ARCH_MULTI_V5
 	bool "OMAP850 Based System"
 	select ARCH_OMAP_OTG
 	select CPU_ARM926T
 
 config ARCH_OMAP15XX
+	depends on ARCH_MULTI_V4T
 	default y
 	bool "OMAP15xx Based System"
 	select CPU_ARM925T
 	select OMAP_MPU_TIMER
 
 config ARCH_OMAP16XX
+	depends on ARCH_MULTI_V5
 	bool "OMAP16xx Based System"
 	select ARCH_OMAP_OTG
 	select CPU_ARM926T
 	select OMAP_DM_TIMER
 
+config ARCH_OMAP1_ANY
+	select ARCH_OMAP
+	def_bool ARCH_OMAP730 || ARCH_OMAP850 || ARCH_OMAP15XX || ARCH_OMAP16XX
+
+config ARCH_OMAP
+	bool
+
+comment "OMAP Feature Selections"
+
 config OMAP_MUX
 	bool "OMAP multiplexing support"
 	default y
@@ -53,11 +79,60 @@ config OMAP_MUX_WARNINGS
 	  to change the pin multiplexing setup.	 When there are no warnings
 	  printed, it's safe to deselect OMAP_MUX for your product.
 
+config OMAP_32K_TIMER
+	bool "Use 32KHz timer"
+	depends on ARCH_OMAP16XX
+	default ARCH_OMAP16XX
+	help
+	  Select this option if you want to enable the OMAP 32KHz timer.
+	  This timer saves power compared to the OMAP_MPU_TIMER, and has
+	  support for no tick during idle. The 32KHz timer provides less
+	  intra-tick resolution than OMAP_MPU_TIMER. The 32KHz timer is
+	  currently only available for OMAP16XX, 24XX, 34XX, OMAP4/5 and DRA7XX.
+
+	  On OMAP2PLUS this value is only used for CONFIG_HZ and
+	  CLOCK_TICK_RATE compile time calculation.
+	  The actual timer selection is done in the board file
+	  through the (DT_)MACHINE_START structure.
+
+config OMAP_MPU_TIMER
+	bool "Use mpu timer"
+	depends on ARCH_OMAP1
+	help
+	  Select this option if you want to use the OMAP mpu timer. This
+	  timer provides more intra-tick resolution than the 32KHz timer,
+	  but consumes more power.
+
+config OMAP_SERIAL_WAKE
+	bool "Enable wake-up events for serial ports"
+	depends on ARCH_OMAP1 && OMAP_MUX
+	default y
+	help
+	  Select this option if you want to have your system wake up
+	  to data on the serial RX line. This allows you to wake the
+	  system from serial console.
+
+config OMAP_RESET_CLOCKS
+	bool "Reset unused clocks during boot"
+	depends on ARCH_OMAP
+	help
+	  Say Y if you want to reset unused clocks during boot.
+	  This option saves power, but assumes all drivers are
+	  using the clock framework. Broken drivers that do not
+	  yet use clock framework may not work with this option.
+	  If you are booting from another operating system, you
+	  probably do not want this option enabled until your
+	  device drivers work properly.
+
+config ARCH_OMAP_OTG
+	bool
+
 comment "OMAP Board Type"
 
 config MACH_OMAP_INNOVATOR
 	bool "TI Innovator"
 	depends on ARCH_OMAP15XX || ARCH_OMAP16XX
+	depends on UNUSED_BOARD_FILES
 	help
           TI OMAP 1510 or 1610 Innovator board support. Say Y here if you
           have such a board.
@@ -65,6 +140,7 @@ config MACH_OMAP_INNOVATOR
 config MACH_OMAP_H2
 	bool "TI H2 Support"
 	depends on ARCH_OMAP16XX
+	depends on UNUSED_BOARD_FILES
 	help
 	  TI OMAP 1610/1611B H2 board support. Say Y here if you have such
 	  a board.
@@ -72,6 +148,7 @@ config MACH_OMAP_H2
 config MACH_OMAP_H3
 	bool "TI H3 Support"
 	depends on ARCH_OMAP16XX
+	depends on UNUSED_BOARD_FILES
 	help
 	  TI OMAP 1710 H3 board support. Say Y here if you have such
 	  a board.
@@ -79,6 +156,7 @@ config MACH_OMAP_H3
 config MACH_HERALD
 	bool "HTC Herald"
 	depends on ARCH_OMAP850
+	depends on UNUSED_BOARD_FILES
 	help
 	  HTC Herald smartphone support (AKA T-Mobile Wing, ...)
 
@@ -92,6 +170,7 @@ config MACH_OMAP_OSK
 config OMAP_OSK_MISTRAL
 	bool "Mistral QVGA board Support"
 	depends on MACH_OMAP_OSK
+	depends on UNUSED_BOARD_FILES
 	help
 	  The OSK supports an optional add-on board with a Quarter-VGA
 	  touchscreen, PDA-ish buttons, a resume button, bicolor LED,
@@ -100,6 +179,7 @@ config OMAP_OSK_MISTRAL
 config MACH_OMAP_PERSEUS2
 	bool "TI Perseus2"
 	depends on ARCH_OMAP730
+	depends on UNUSED_BOARD_FILES
 	help
 	  Support for TI OMAP 730 Perseus2 board. Say Y here if you have such
 	  a board.
@@ -107,6 +187,7 @@ config MACH_OMAP_PERSEUS2
 config MACH_OMAP_FSAMPLE
 	bool "TI F-Sample"
 	depends on ARCH_OMAP730
+	depends on UNUSED_BOARD_FILES
 	help
 	  Support for TI OMAP 850 F-Sample board. Say Y here if you have such
 	  a board.
@@ -123,6 +204,7 @@ config MACH_OMAP_PALMTE
 config MACH_OMAP_PALMZ71
 	bool "Palm Zire71"
 	depends on ARCH_OMAP15XX
+	depends on UNUSED_BOARD_FILES
 	help
 	 Support for the Palm Zire71 PDA. To boot the kernel,
 	 you'll need a PalmOS compatible bootloader; check out
@@ -132,6 +214,7 @@ config MACH_OMAP_PALMZ71
 config MACH_OMAP_PALMTT
 	bool "Palm Tungsten|T"
 	depends on ARCH_OMAP15XX
+	depends on UNUSED_BOARD_FILES
 	help
 	  Support for the Palm Tungsten|T PDA. To boot the kernel, you'll
 	  need a PalmOS compatible bootloader (Garux); check out
@@ -172,6 +255,7 @@ config MACH_AMS_DELTA
 config MACH_OMAP_GENERIC
 	bool "Generic OMAP board"
 	depends on ARCH_OMAP15XX || ARCH_OMAP16XX
+	depends on UNUSED_BOARD_FILES
 	help
           Support for generic OMAP-1510, 1610 or 1710 board with
           no FPGA. Can be used as template for porting Linux to
diff --git a/arch/arm/mach-omap1/Makefile b/arch/arm/mach-omap1/Makefile
index c757a52d0801..506074b86333 100644
--- a/arch/arm/mach-omap1/Makefile
+++ b/arch/arm/mach-omap1/Makefile
@@ -3,9 +3,11 @@
 # Makefile for the linux kernel.
 #
 
+ifdef CONFIG_ARCH_OMAP1_ANY
+
 # Common support
 obj-y := io.o id.o sram-init.o sram.o time.o irq.o mux.o flash.o \
-	 serial.o devices.o dma.o fb.o
+	 serial.o devices.o dma.o omap-dma.o fb.o
 obj-y += clock.o clock_data.o opp_data.o reset.o pm_bus.o timer.o
 
 ifneq ($(CONFIG_SND_SOC_OMAP_MCBSP),)
@@ -58,6 +60,4 @@ obj-$(CONFIG_ARCH_OMAP850)		+= gpio7xx.o
 obj-$(CONFIG_ARCH_OMAP15XX)		+= gpio15xx.o
 obj-$(CONFIG_ARCH_OMAP16XX)		+= gpio16xx.o
 
-ifneq ($(CONFIG_FB_OMAP),)
-obj-y += lcd_dma.o
 endif
diff --git a/arch/arm/mach-omap1/Makefile.boot b/arch/arm/mach-omap1/Makefile.boot
deleted file mode 100644
index 2c771515a606..000000000000
--- a/arch/arm/mach-omap1/Makefile.boot
+++ /dev/null
@@ -1,4 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0-only
-   zreladdr-y		+= 0x10008000
-params_phys-y		:= 0x10000100
-initrd_phys-y		:= 0x10800000
diff --git a/arch/arm/mach-omap1/ams-delta-fiq-handler.S b/arch/arm/mach-omap1/ams-delta-fiq-handler.S
index f745a65d3bd7..35c2f9574dbd 100644
--- a/arch/arm/mach-omap1/ams-delta-fiq-handler.S
+++ b/arch/arm/mach-omap1/ams-delta-fiq-handler.S
@@ -13,14 +13,15 @@
 #include <linux/linkage.h>
 #include <linux/platform_data/ams-delta-fiq.h>
 #include <linux/platform_data/gpio-omap.h>
+#include <linux/soc/ti/omap1-io.h>
 
 #include <asm/assembler.h>
 #include <asm/irq.h>
 
+#include "hardware.h"
 #include "ams-delta-fiq.h"
 #include "board-ams-delta.h"
 #include "iomap.h"
-#include "soc.h"
 
 /*
  * OMAP1510 GPIO related symbol copied from arch/arm/mach-omap1/gpio15xx.c.
diff --git a/arch/arm/mach-omap1/ams-delta-fiq.c b/arch/arm/mach-omap1/ams-delta-fiq.c
index 4eea3e39e633..1f5852be057e 100644
--- a/arch/arm/mach-omap1/ams-delta-fiq.c
+++ b/arch/arm/mach-omap1/ams-delta-fiq.c
@@ -21,7 +21,9 @@
 #include <linux/platform_device.h>
 
 #include <asm/fiq.h>
+#include <linux/soc/ti/omap1-io.h>
 
+#include "hardware.h"
 #include "ams-delta-fiq.h"
 #include "board-ams-delta.h"
 
diff --git a/arch/arm/mach-omap1/ams-delta-fiq.h b/arch/arm/mach-omap1/ams-delta-fiq.h
index fd76df3cce37..7f843caedb7c 100644
--- a/arch/arm/mach-omap1/ams-delta-fiq.h
+++ b/arch/arm/mach-omap1/ams-delta-fiq.h
@@ -16,7 +16,7 @@
 #ifndef __AMS_DELTA_FIQ_H
 #define __AMS_DELTA_FIQ_H
 
-#include <mach/irqs.h>
+#include "irqs.h"
 
 /*
  * Interrupt number used for passing control from FIQ to IRQ.
diff --git a/arch/arm/mach-omap1/board-ams-delta.c b/arch/arm/mach-omap1/board-ams-delta.c
index 1026a816dcc0..651c28d81132 100644
--- a/arch/arm/mach-omap1/board-ams-delta.c
+++ b/arch/arm/mach-omap1/board-ams-delta.c
@@ -28,6 +28,7 @@
 #include <linux/omapfb.h>
 #include <linux/io.h>
 #include <linux/platform_data/gpio-omap.h>
+#include <linux/soc/ti/omap1-mux.h>
 
 #include <asm/serial.h>
 #include <asm/mach-types.h>
@@ -35,11 +36,9 @@
 #include <asm/mach/map.h>
 
 #include <linux/platform_data/keypad-omap.h>
-#include <mach/mux.h>
-
-#include <mach/hardware.h>
-#include <mach/usb.h>
 
+#include "hardware.h"
+#include "usb.h"
 #include "ams-delta-fiq.h"
 #include "board-ams-delta.h"
 #include "iomap.h"
@@ -407,9 +406,6 @@ static struct gpio_led gpio_leds[] __initdata = {
 	[LATCH1_PIN_LED_CAMERA] = {
 		.name		 = "camera",
 		.default_state	 = LEDS_GPIO_DEFSTATE_OFF,
-#ifdef CONFIG_LEDS_TRIGGERS
-		.default_trigger = "ams_delta_camera",
-#endif
 	},
 	[LATCH1_PIN_LED_ADVERT] = {
 		.name		 = "advert",
@@ -456,10 +452,6 @@ static struct gpiod_lookup_table leds_gpio_table = {
 	},
 };
 
-#ifdef CONFIG_LEDS_TRIGGERS
-DEFINE_LED_TRIGGER(ams_delta_camera_led_trigger);
-#endif
-
 static struct platform_device ams_delta_audio_device = {
 	.name   = "ams-delta-audio",
 	.id     = -1,
@@ -672,7 +664,7 @@ static void __init ams_delta_latch2_init(void)
 {
 	u16 latch2 = 1 << LATCH2_PIN_MODEM_NRESET | 1 << LATCH2_PIN_MODEM_CODEC;
 
-	__raw_writew(latch2, LATCH2_VIRT);
+	__raw_writew(latch2, IOMEM(LATCH2_VIRT));
 }
 
 static void __init ams_delta_init(void)
@@ -705,10 +697,6 @@ static void __init ams_delta_init(void)
 	omap_register_i2c_bus(1, 100, NULL, 0);
 
 	omap1_usb_init(&ams_delta_usb_config);
-#ifdef CONFIG_LEDS_TRIGGERS
-	led_trigger_register_simple("ams_delta_camera",
-			&ams_delta_camera_led_trigger);
-#endif
 	platform_add_devices(ams_delta_devices, ARRAY_SIZE(ams_delta_devices));
 
 	/*
diff --git a/arch/arm/mach-omap1/board-fsample.c b/arch/arm/mach-omap1/board-fsample.c
index c3aa6f2e5546..f21e15c7b973 100644
--- a/arch/arm/mach-omap1/board-fsample.c
+++ b/arch/arm/mach-omap1/board-fsample.c
@@ -23,13 +23,13 @@
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
 
-#include <mach/tc.h>
-#include <mach/mux.h>
-#include "flash.h"
+#include <linux/soc/ti/omap1-io.h>
 #include <linux/platform_data/keypad-omap.h>
+#include "tc.h"
 
-#include <mach/hardware.h>
-
+#include "mux.h"
+#include "flash.h"
+#include "hardware.h"
 #include "iomap.h"
 #include "common.h"
 #include "fpga.h"
diff --git a/arch/arm/mach-omap1/board-generic.c b/arch/arm/mach-omap1/board-generic.c
index c62554990115..3b2bcaf4bb01 100644
--- a/arch/arm/mach-omap1/board-generic.c
+++ b/arch/arm/mach-omap1/board-generic.c
@@ -14,15 +14,13 @@
 #include <linux/init.h>
 #include <linux/platform_device.h>
 
-#include <mach/hardware.h>
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
 
-#include <mach/mux.h>
-
-#include <mach/usb.h>
-
+#include "hardware.h"
+#include "mux.h"
+#include "usb.h"
 #include "common.h"
 
 /* assume no Mini-AB port */
diff --git a/arch/arm/mach-omap1/board-h2.c b/arch/arm/mach-omap1/board-h2.c
index 977b0b744c22..f28a4c3ea501 100644
--- a/arch/arm/mach-omap1/board-h2.c
+++ b/arch/arm/mach-omap1/board-h2.c
@@ -28,22 +28,20 @@
 #include <linux/mfd/tps65010.h>
 #include <linux/smc91x.h>
 #include <linux/omapfb.h>
+#include <linux/omap-dma.h>
 #include <linux/platform_data/gpio-omap.h>
+#include <linux/platform_data/keypad-omap.h>
 #include <linux/leds.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
 
-#include <mach/mux.h>
-#include <linux/omap-dma.h>
-#include <mach/tc.h>
-#include <linux/platform_data/keypad-omap.h>
+#include "tc.h"
+#include "mux.h"
 #include "flash.h"
-
-#include <mach/hardware.h>
-#include <mach/usb.h>
-
+#include "hardware.h"
+#include "usb.h"
 #include "common.h"
 #include "board-h2.h"
 
diff --git a/arch/arm/mach-omap1/board-h3.c b/arch/arm/mach-omap1/board-h3.c
index 4249984f9c30..1e4c57710fcc 100644
--- a/arch/arm/mach-omap1/board-h3.c
+++ b/arch/arm/mach-omap1/board-h3.c
@@ -29,6 +29,8 @@
 #include <linux/smc91x.h>
 #include <linux/omapfb.h>
 #include <linux/platform_data/gpio-omap.h>
+#include <linux/platform_data/keypad-omap.h>
+#include <linux/omap-dma.h>
 #include <linux/leds.h>
 
 #include <asm/setup.h>
@@ -37,16 +39,12 @@
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
 
-#include <mach/mux.h>
-#include <mach/tc.h>
-#include <linux/platform_data/keypad-omap.h>
-#include <linux/omap-dma.h>
+#include "tc.h"
+#include "mux.h"
 #include "flash.h"
-
-#include <mach/hardware.h>
-#include <mach/irqs.h>
-#include <mach/usb.h>
-
+#include "hardware.h"
+#include "irqs.h"
+#include "usb.h"
 #include "common.h"
 #include "board-h3.h"
 
diff --git a/arch/arm/mach-omap1/board-htcherald.c b/arch/arm/mach-omap1/board-htcherald.c
index 258304edf23e..291d294b5824 100644
--- a/arch/arm/mach-omap1/board-htcherald.c
+++ b/arch/arm/mach-omap1/board-htcherald.c
@@ -23,16 +23,16 @@
 #include <linux/spi/ads7846.h>
 #include <linux/omapfb.h>
 #include <linux/platform_data/keypad-omap.h>
+#include <linux/soc/ti/omap1-io.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
 
-#include <mach/omap7xx.h>
+#include "hardware.h"
+#include "omap7xx.h"
 #include "mmc.h"
-
-#include <mach/irqs.h>
-#include <mach/usb.h>
-
+#include "irqs.h"
+#include "usb.h"
 #include "common.h"
 
 /* LCD register definition */
@@ -141,13 +141,6 @@
 #define HTCPLD_GPIO_DOWN_DPAD		HTCPLD_BASE(7, 4)
 #define HTCPLD_GPIO_ENTER_DPAD		HTCPLD_BASE(7, 3)
 
-/*
- * The htcpld chip requires a gpio write to a specific line
- * to re-enable interrupts after one has occurred.
- */
-#define HTCPLD_GPIO_INT_RESET_HI	HTCPLD_BASE(2, 7)
-#define HTCPLD_GPIO_INT_RESET_LO	HTCPLD_BASE(2, 0)
-
 /* Chip 5 */
 #define HTCPLD_IRQ_RIGHT_KBD		HTCPLD_IRQ(0, 7)
 #define HTCPLD_IRQ_UP_KBD		HTCPLD_IRQ(0, 6)
@@ -170,7 +163,7 @@ static const unsigned int htc_herald_keymap[] = {
 	KEY(3, 0, KEY_VOLUMEUP), /* Volume up */
 	KEY(4, 0, KEY_F2),  /* Right bar (landscape) */
 	KEY(5, 0, KEY_MAIL), /* Win key (portrait) */
-	KEY(6, 0, KEY_DIRECTORY), /* Right bar (protrait) */
+	KEY(6, 0, KEY_DIRECTORY), /* Right bar (portrait) */
 	KEY(0, 1, KEY_LEFTCTRL), /* Windows key */
 	KEY(1, 1, KEY_COMMA),
 	KEY(2, 1, KEY_M),
@@ -348,8 +341,6 @@ static struct htcpld_chip_platform_data htcpld_chips[] = {
 };
 
 static struct htcpld_core_platform_data htcpld_pfdata = {
-	.int_reset_gpio_hi = HTCPLD_GPIO_INT_RESET_HI,
-	.int_reset_gpio_lo = HTCPLD_GPIO_INT_RESET_LO,
 	.i2c_adapter_id	   = 1,
 
 	.chip		   = htcpld_chips,
diff --git a/arch/arm/mach-omap1/board-innovator.c b/arch/arm/mach-omap1/board-innovator.c
index cbe093f969d5..6deb4ca079e9 100644
--- a/arch/arm/mach-omap1/board-innovator.c
+++ b/arch/arm/mach-omap1/board-innovator.c
@@ -23,19 +23,17 @@
 #include <linux/input.h>
 #include <linux/smc91x.h>
 #include <linux/omapfb.h>
+#include <linux/platform_data/keypad-omap.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
 
-#include <mach/mux.h>
+#include "tc.h"
+#include "mux.h"
 #include "flash.h"
-#include <mach/tc.h>
-#include <linux/platform_data/keypad-omap.h>
-
-#include <mach/hardware.h>
-#include <mach/usb.h>
-
+#include "hardware.h"
+#include "usb.h"
 #include "iomap.h"
 #include "common.h"
 #include "mmc.h"
@@ -194,6 +192,9 @@ static struct platform_device innovator1510_smc91x_device = {
 static struct platform_device innovator1510_lcd_device = {
 	.name		= "lcd_inn1510",
 	.id		= -1,
+	.dev	= {
+		.platform_data = (void __force *)OMAP1510_FPGA_LCD_PANEL_CONTROL,
+	}
 };
 
 static struct platform_device innovator1510_spi_device = {
@@ -287,6 +288,23 @@ static void __init innovator_init_smc91x(void)
 }
 
 #ifdef CONFIG_ARCH_OMAP15XX
+/*
+ * Board specific gang-switched transceiver power on/off.
+ */
+static int innovator_omap_ohci_transceiver_power(int on)
+{
+	if (on)
+		__raw_writeb(__raw_readb(INNOVATOR_FPGA_CAM_USB_CONTROL)
+				| ((1 << 5/*usb1*/) | (1 << 3/*usb2*/)),
+			       INNOVATOR_FPGA_CAM_USB_CONTROL);
+	else
+		__raw_writeb(__raw_readb(INNOVATOR_FPGA_CAM_USB_CONTROL)
+				& ~((1 << 5/*usb1*/) | (1 << 3/*usb2*/)),
+			       INNOVATOR_FPGA_CAM_USB_CONTROL);
+
+	return 0;
+}
+
 static struct omap_usb_config innovator1510_usb_config __initdata = {
 	/* for bundled non-standard host and peripheral cables */
 	.hmc_mode	= 4,
@@ -297,6 +315,8 @@ static struct omap_usb_config innovator1510_usb_config __initdata = {
 
 	.register_dev	= 1,
 	.pins[0]	= 2,
+
+	.transceiver_power = innovator_omap_ohci_transceiver_power,
 };
 
 static const struct omap_lcd_config innovator1510_lcd_config __initconst = {
diff --git a/arch/arm/mach-omap1/board-nokia770.c b/arch/arm/mach-omap1/board-nokia770.c
index 11511ae2e0a2..8e0e58495023 100644
--- a/arch/arm/mach-omap1/board-nokia770.c
+++ b/arch/arm/mach-omap1/board-nokia770.c
@@ -28,11 +28,9 @@
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
 
-#include <mach/mux.h>
-
-#include <mach/hardware.h>
-#include <mach/usb.h>
-
+#include "mux.h"
+#include "hardware.h"
+#include "usb.h"
 #include "common.h"
 #include "clock.h"
 #include "mmc.h"
diff --git a/arch/arm/mach-omap1/board-osk.c b/arch/arm/mach-omap1/board-osk.c
index e18b6f13300e..76684b7a4e87 100644
--- a/arch/arm/mach-omap1/board-osk.c
+++ b/arch/arm/mach-omap1/board-osk.c
@@ -42,18 +42,17 @@
 #include <linux/mfd/tps65010.h>
 #include <linux/platform_data/gpio-omap.h>
 #include <linux/platform_data/omap1_bl.h>
+#include <linux/soc/ti/omap1-io.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
 
+#include "tc.h"
 #include "flash.h"
-#include <mach/mux.h>
-#include <mach/tc.h>
-
-#include <mach/hardware.h>
-#include <mach/usb.h>
-
+#include "mux.h"
+#include "hardware.h"
+#include "usb.h"
 #include "common.h"
 
 /* Name of the GPIO chip used by the OMAP for GPIOs 0..15 */
@@ -153,14 +152,14 @@ static struct resource osk5912_cf_resources[] = {
 	[0] = {
 		.flags	= IORESOURCE_IRQ,
 	},
+	[1] = {
+		.flags = IORESOURCE_MEM,
+	},
 };
 
 static struct platform_device osk5912_cf_device = {
 	.name		= "omap_cf",
 	.id		= -1,
-	.dev = {
-		.platform_data	= (void *) 2 /* CS2 */,
-	},
 	.num_resources	= ARRAY_SIZE(osk5912_cf_resources),
 	.resource	= osk5912_cf_resources,
 };
@@ -275,13 +274,41 @@ static void __init osk_init_smc91x(void)
 	omap_writel(l, EMIFS_CCS(1));
 }
 
-static void __init osk_init_cf(void)
+static void __init osk_init_cf(int seg)
 {
+	struct resource *res = &osk5912_cf_resources[1];
+
 	omap_cfg_reg(M7_1610_GPIO62);
 	if ((gpio_request(62, "cf_irq")) < 0) {
 		printk("Error requesting gpio 62 for CF irq\n");
 		return;
 	}
+
+	switch (seg) {
+	/* NOTE: CS0 could be configured too ... */
+	case 1:
+		res->start = OMAP_CS1_PHYS;
+		break;
+	case 2:
+		res->start = OMAP_CS2_PHYS;
+		break;
+	case 3:
+		res->start = omap_cs3_phys();
+		break;
+	}
+
+	res->end = res->start + SZ_8K - 1;
+	osk5912_cf_device.dev.platform_data = (void *)(uintptr_t)seg;
+
+	/* NOTE:  better EMIFS setup might support more cards; but the
+	 * TRM only shows how to affect regular flash signals, not their
+	 * CF/PCMCIA variants...
+	 */
+	pr_debug("%s: cs%d, previous ccs %08x acs %08x\n", __func__,
+		seg, omap_readl(EMIFS_CCS(seg)), omap_readl(EMIFS_ACS(seg)));
+	omap_writel(0x0004a1b3, EMIFS_CCS(seg));	/* synch mode 4 etc */
+	omap_writel(0x00000000, EMIFS_ACS(seg));	/* OE hold/setup */
+
 	/* the CF I/O IRQ is really active-low */
 	irq_set_irq_type(gpio_to_irq(62), IRQ_TYPE_EDGE_FALLING);
 }
@@ -580,7 +607,7 @@ static void __init osk_init(void)
 	u32 l;
 
 	osk_init_smc91x();
-	osk_init_cf();
+	osk_init_cf(2); /* CS2 */
 
 	/* Workaround for wrong CS3 (NOR flash) timing
 	 * There are some U-Boot versions out there which configure
diff --git a/arch/arm/mach-omap1/board-palmte.c b/arch/arm/mach-omap1/board-palmte.c
index ce6f0fcd9d12..72e1979c7a8b 100644
--- a/arch/arm/mach-omap1/board-palmte.c
+++ b/arch/arm/mach-omap1/board-palmte.c
@@ -25,21 +25,19 @@
 #include <linux/interrupt.h>
 #include <linux/apm-emulation.h>
 #include <linux/omapfb.h>
+#include <linux/omap-dma.h>
+#include <linux/platform_data/keypad-omap.h>
 #include <linux/platform_data/omap1_bl.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
 
+#include "tc.h"
 #include "flash.h"
-#include <mach/mux.h>
-#include <mach/tc.h>
-#include <linux/omap-dma.h>
-#include <linux/platform_data/keypad-omap.h>
-
-#include <mach/hardware.h>
-#include <mach/usb.h>
-
+#include "mux.h"
+#include "hardware.h"
+#include "usb.h"
 #include "mmc.h"
 #include "common.h"
 
diff --git a/arch/arm/mach-omap1/board-palmtt.c b/arch/arm/mach-omap1/board-palmtt.c
index 8a08311c4e05..537f0e6a2ff7 100644
--- a/arch/arm/mach-omap1/board-palmtt.c
+++ b/arch/arm/mach-omap1/board-palmtt.c
@@ -24,22 +24,20 @@
 #include <linux/omapfb.h>
 #include <linux/spi/spi.h>
 #include <linux/spi/ads7846.h>
+#include <linux/omap-dma.h>
 #include <linux/platform_data/omap1_bl.h>
 #include <linux/platform_data/leds-omap.h>
+#include <linux/platform_data/keypad-omap.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
 
+#include "tc.h"
 #include "flash.h"
-#include <mach/mux.h>
-#include <linux/omap-dma.h>
-#include <mach/tc.h>
-#include <linux/platform_data/keypad-omap.h>
-
-#include <mach/hardware.h>
-#include <mach/usb.h>
-
+#include "mux.h"
+#include "hardware.h"
+#include "usb.h"
 #include "common.h"
 
 #define PALMTT_USBDETECT_GPIO	0
diff --git a/arch/arm/mach-omap1/board-palmz71.c b/arch/arm/mach-omap1/board-palmz71.c
index 034e5bc6a029..47f08ae5a2f3 100644
--- a/arch/arm/mach-omap1/board-palmz71.c
+++ b/arch/arm/mach-omap1/board-palmz71.c
@@ -28,20 +28,18 @@
 #include <linux/spi/spi.h>
 #include <linux/spi/ads7846.h>
 #include <linux/platform_data/omap1_bl.h>
+#include <linux/platform_data/keypad-omap.h>
+#include <linux/omap-dma.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
 
+#include "tc.h"
 #include "flash.h"
-#include <mach/mux.h>
-#include <linux/omap-dma.h>
-#include <mach/tc.h>
-#include <linux/platform_data/keypad-omap.h>
-
-#include <mach/hardware.h>
-#include <mach/usb.h>
-
+#include "mux.h"
+#include "hardware.h"
+#include "usb.h"
 #include "common.h"
 
 #define PALMZ71_USBDETECT_GPIO	0
diff --git a/arch/arm/mach-omap1/board-perseus2.c b/arch/arm/mach-omap1/board-perseus2.c
index 1aeeb7337d29..b041e6f6e9cf 100644
--- a/arch/arm/mach-omap1/board-perseus2.c
+++ b/arch/arm/mach-omap1/board-perseus2.c
@@ -19,17 +19,16 @@
 #include <linux/smc91x.h>
 #include <linux/omapfb.h>
 #include <linux/platform_data/keypad-omap.h>
+#include <linux/soc/ti/omap1-io.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
 
-#include <mach/tc.h>
-#include <mach/mux.h>
+#include "tc.h"
+#include "mux.h"
 #include "flash.h"
-
-#include <mach/hardware.h>
-
+#include "hardware.h"
 #include "iomap.h"
 #include "common.h"
 #include "fpga.h"
@@ -289,6 +288,12 @@ static void __init omap_perseus2_init(void)
 	omap_cfg_reg(F4_7XX_KBC3);
 	omap_cfg_reg(E3_7XX_KBC4);
 
+	if (IS_ENABLED(CONFIG_SPI_OMAP_UWIRE)) {
+		/* configure pins: MPU_UW_nSCS1, MPU_UW_SDO, MPU_UW_SCLK */
+		int val = omap_readl(OMAP7XX_IO_CONF_9) & ~0x00EEE000;
+		omap_writel(val | 0x00AAA000, OMAP7XX_IO_CONF_9);
+	}
+
 	platform_add_devices(devices, ARRAY_SIZE(devices));
 
 	omap_serial_init();
diff --git a/arch/arm/mach-omap1/board-sx1-mmc.c b/arch/arm/mach-omap1/board-sx1-mmc.c
index 6192b1da75cb..f1c160924dfe 100644
--- a/arch/arm/mach-omap1/board-sx1-mmc.c
+++ b/arch/arm/mach-omap1/board-sx1-mmc.c
@@ -12,9 +12,8 @@
 #include <linux/gpio.h>
 #include <linux/platform_device.h>
 
-#include <mach/hardware.h>
+#include "hardware.h"
 #include "board-sx1.h"
-
 #include "mmc.h"
 
 #if IS_ENABLED(CONFIG_MMC_OMAP)
diff --git a/arch/arm/mach-omap1/board-sx1.c b/arch/arm/mach-omap1/board-sx1.c
index bb9ec345e204..f0dbb0e8d8e7 100644
--- a/arch/arm/mach-omap1/board-sx1.c
+++ b/arch/arm/mach-omap1/board-sx1.c
@@ -26,20 +26,18 @@
 #include <linux/export.h>
 #include <linux/omapfb.h>
 #include <linux/platform_data/keypad-omap.h>
+#include <linux/omap-dma.h>
+#include "tc.h"
 
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
 
 #include "flash.h"
-#include <mach/mux.h>
-#include <linux/omap-dma.h>
-#include <mach/tc.h>
+#include "mux.h"
 #include "board-sx1.h"
-
-#include <mach/hardware.h>
-#include <mach/usb.h>
-
+#include "hardware.h"
+#include "usb.h"
 #include "common.h"
 
 /* Write to I2C device */
diff --git a/arch/arm/mach-omap1/board-sx1.h b/arch/arm/mach-omap1/board-sx1.h
index 355adbdaae33..fafe54a2e444 100644
--- a/arch/arm/mach-omap1/board-sx1.h
+++ b/arch/arm/mach-omap1/board-sx1.h
@@ -1,15 +1,8 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * Siemens SX1 board definitions
  *
  * Copyright: Vovan888 at gmail com
- *
- * This package is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- * THIS PACKAGE IS PROVIDED ``AS IS'' AND WITHOUT ANY EXPRESS OR
- * IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED
- * WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR A PARTICULAR PURPOSE.
  */
 
 #ifndef __ASM_ARCH_SX1_I2C_CHIPS_H
diff --git a/arch/arm/mach-omap1/clock.c b/arch/arm/mach-omap1/clock.c
index 9d4a0ab50a46..83381e23fab9 100644
--- a/arch/arm/mach-omap1/clock.c
+++ b/arch/arm/mach-omap1/clock.c
@@ -16,11 +16,13 @@
 #include <linux/io.h>
 #include <linux/clk.h>
 #include <linux/clkdev.h>
+#include <linux/clk-provider.h>
+#include <linux/soc/ti/omap1-io.h>
+#include <linux/spinlock.h>
 
 #include <asm/mach-types.h>
 
-#include <mach/hardware.h>
-
+#include "hardware.h"
 #include "soc.h"
 #include "iomap.h"
 #include "clock.h"
@@ -28,33 +30,37 @@
 #include "sram.h"
 
 __u32 arm_idlect1_mask;
-struct clk *api_ck_p, *ck_dpll1_p, *ck_ref_p;
+/* provide direct internal access (not via clk API) to some clocks */
+struct omap1_clk *api_ck_p, *ck_dpll1_p, *ck_ref_p;
 
-static LIST_HEAD(clocks);
-static DEFINE_MUTEX(clocks_mutex);
-static DEFINE_SPINLOCK(clockfw_lock);
+/* protect registeres shared among clk_enable/disable() and clk_set_rate() operations */
+static DEFINE_SPINLOCK(arm_ckctl_lock);
+static DEFINE_SPINLOCK(arm_idlect2_lock);
+static DEFINE_SPINLOCK(mod_conf_ctrl_0_lock);
+static DEFINE_SPINLOCK(mod_conf_ctrl_1_lock);
+static DEFINE_SPINLOCK(swd_clk_div_ctrl_sel_lock);
 
 /*
  * Omap1 specific clock functions
  */
 
-unsigned long omap1_uart_recalc(struct clk *clk)
+unsigned long omap1_uart_recalc(struct omap1_clk *clk, unsigned long p_rate)
 {
 	unsigned int val = __raw_readl(clk->enable_reg);
-	return val & clk->enable_bit ? 48000000 : 12000000;
+	return val & 1 << clk->enable_bit ? 48000000 : 12000000;
 }
 
-unsigned long omap1_sossi_recalc(struct clk *clk)
+unsigned long omap1_sossi_recalc(struct omap1_clk *clk, unsigned long p_rate)
 {
 	u32 div = omap_readl(MOD_CONF_CTRL_1);
 
 	div = (div >> 17) & 0x7;
 	div++;
 
-	return clk->parent->rate / div;
+	return p_rate / div;
 }
 
-static void omap1_clk_allow_idle(struct clk *clk)
+static void omap1_clk_allow_idle(struct omap1_clk *clk)
 {
 	struct arm_idlect1_clk * iclk = (struct arm_idlect1_clk *)clk;
 
@@ -65,7 +71,7 @@ static void omap1_clk_allow_idle(struct clk *clk)
 		arm_idlect1_mask |= 1 << iclk->idlect_shift;
 }
 
-static void omap1_clk_deny_idle(struct clk *clk)
+static void omap1_clk_deny_idle(struct omap1_clk *clk)
 {
 	struct arm_idlect1_clk * iclk = (struct arm_idlect1_clk *)clk;
 
@@ -129,7 +135,7 @@ static __u16 verify_ckctl_value(__u16 newval)
 	return newval;
 }
 
-static int calc_dsor_exp(struct clk *clk, unsigned long rate)
+static int calc_dsor_exp(unsigned long rate, unsigned long realrate)
 {
 	/* Note: If target frequency is too low, this function will return 4,
 	 * which is invalid value. Caller must check for this value and act
@@ -142,15 +148,11 @@ static int calc_dsor_exp(struct clk *clk, unsigned long rate)
 	 * DSP_CK >= TC_CK
 	 * DSPMMU_CK >= TC_CK
 	 */
-	unsigned long realrate;
-	struct clk * parent;
 	unsigned  dsor_exp;
 
-	parent = clk->parent;
-	if (unlikely(parent == NULL))
+	if (unlikely(realrate == 0))
 		return -EIO;
 
-	realrate = parent->rate;
 	for (dsor_exp=0; dsor_exp<4; dsor_exp++) {
 		if (realrate <= rate)
 			break;
@@ -161,16 +163,50 @@ static int calc_dsor_exp(struct clk *clk, unsigned long rate)
 	return dsor_exp;
 }
 
-unsigned long omap1_ckctl_recalc(struct clk *clk)
+unsigned long omap1_ckctl_recalc(struct omap1_clk *clk, unsigned long p_rate)
 {
 	/* Calculate divisor encoded as 2-bit exponent */
 	int dsor = 1 << (3 & (omap_readw(ARM_CKCTL) >> clk->rate_offset));
 
-	return clk->parent->rate / dsor;
+	/* update locally maintained rate, required by arm_ck for omap1_show_rates() */
+	clk->rate = p_rate / dsor;
+	return clk->rate;
+}
+
+static int omap1_clk_is_enabled(struct clk_hw *hw)
+{
+	struct omap1_clk *clk = to_omap1_clk(hw);
+	bool api_ck_was_enabled = true;
+	__u32 regval32;
+	int ret;
+
+	if (!clk->ops)	/* no gate -- always enabled */
+		return 1;
+
+	if (clk->ops == &clkops_dspck) {
+		api_ck_was_enabled = omap1_clk_is_enabled(&api_ck_p->hw);
+		if (!api_ck_was_enabled)
+			if (api_ck_p->ops->enable(api_ck_p) < 0)
+				return 0;
+	}
+
+	if (clk->flags & ENABLE_REG_32BIT)
+		regval32 = __raw_readl(clk->enable_reg);
+	else
+		regval32 = __raw_readw(clk->enable_reg);
+
+	ret = regval32 & (1 << clk->enable_bit);
+
+	if (!api_ck_was_enabled)
+		api_ck_p->ops->disable(api_ck_p);
+
+	return ret;
 }
 
-unsigned long omap1_ckctl_recalc_dsp_domain(struct clk *clk)
+
+unsigned long omap1_ckctl_recalc_dsp_domain(struct omap1_clk *clk, unsigned long p_rate)
 {
+	bool api_ck_was_enabled;
 	int dsor;
 
 	/* Calculate divisor encoded as 2-bit exponent
@@ -180,15 +216,18 @@ unsigned long omap1_ckctl_recalc_dsp_domain(struct clk *clk)
 	 * Note that DSP_CKCTL virt addr = phys addr, so
 	 * we must use __raw_readw() instead of omap_readw().
 	 */
-	omap1_clk_enable(api_ck_p);
+	api_ck_was_enabled = omap1_clk_is_enabled(&api_ck_p->hw);
+	if (!api_ck_was_enabled)
+		api_ck_p->ops->enable(api_ck_p);
 	dsor = 1 << (3 & (__raw_readw(DSP_CKCTL) >> clk->rate_offset));
-	omap1_clk_disable(api_ck_p);
+	if (!api_ck_was_enabled)
+		api_ck_p->ops->disable(api_ck_p);
 
-	return clk->parent->rate / dsor;
+	return p_rate / dsor;
 }
 
 /* MPU virtual clock functions */
-int omap1_select_table_rate(struct clk *clk, unsigned long rate)
+int omap1_select_table_rate(struct omap1_clk *clk, unsigned long rate, unsigned long p_rate)
 {
 	/* Find the highest supported frequency <= rate and switch to it */
 	struct mpu_rate * ptr;
@@ -223,12 +262,12 @@ int omap1_select_table_rate(struct clk *clk, unsigned long rate)
 	return 0;
 }
 
-int omap1_clk_set_rate_dsp_domain(struct clk *clk, unsigned long rate)
+int omap1_clk_set_rate_dsp_domain(struct omap1_clk *clk, unsigned long rate, unsigned long p_rate)
 {
 	int dsor_exp;
 	u16 regval;
 
-	dsor_exp = calc_dsor_exp(clk, rate);
+	dsor_exp = calc_dsor_exp(rate, p_rate);
 	if (dsor_exp > 3)
 		dsor_exp = -EINVAL;
 	if (dsor_exp < 0)
@@ -238,42 +277,51 @@ int omap1_clk_set_rate_dsp_domain(struct clk *clk, unsigned long rate)
 	regval &= ~(3 << clk->rate_offset);
 	regval |= dsor_exp << clk->rate_offset;
 	__raw_writew(regval, DSP_CKCTL);
-	clk->rate = clk->parent->rate / (1 << dsor_exp);
+	clk->rate = p_rate / (1 << dsor_exp);
 
 	return 0;
 }
 
-long omap1_clk_round_rate_ckctl_arm(struct clk *clk, unsigned long rate)
+long omap1_clk_round_rate_ckctl_arm(struct omap1_clk *clk, unsigned long rate,
+				    unsigned long *p_rate)
 {
-	int dsor_exp = calc_dsor_exp(clk, rate);
+	int dsor_exp = calc_dsor_exp(rate, *p_rate);
+
 	if (dsor_exp < 0)
 		return dsor_exp;
 	if (dsor_exp > 3)
 		dsor_exp = 3;
-	return clk->parent->rate / (1 << dsor_exp);
+	return *p_rate / (1 << dsor_exp);
 }
 
-int omap1_clk_set_rate_ckctl_arm(struct clk *clk, unsigned long rate)
+int omap1_clk_set_rate_ckctl_arm(struct omap1_clk *clk, unsigned long rate, unsigned long p_rate)
 {
+	unsigned long flags;
 	int dsor_exp;
 	u16 regval;
 
-	dsor_exp = calc_dsor_exp(clk, rate);
+	dsor_exp = calc_dsor_exp(rate, p_rate);
 	if (dsor_exp > 3)
 		dsor_exp = -EINVAL;
 	if (dsor_exp < 0)
 		return dsor_exp;
 
+	/* protect ARM_CKCTL register from concurrent access via clk_enable/disable() */
+	spin_lock_irqsave(&arm_ckctl_lock, flags);
+
 	regval = omap_readw(ARM_CKCTL);
 	regval &= ~(3 << clk->rate_offset);
 	regval |= dsor_exp << clk->rate_offset;
 	regval = verify_ckctl_value(regval);
 	omap_writew(regval, ARM_CKCTL);
-	clk->rate = clk->parent->rate / (1 << dsor_exp);
+	clk->rate = p_rate / (1 << dsor_exp);
+
+	spin_unlock_irqrestore(&arm_ckctl_lock, flags);
+
 	return 0;
 }
 
-long omap1_round_to_table_rate(struct clk *clk, unsigned long rate)
+long omap1_round_to_table_rate(struct omap1_clk *clk, unsigned long rate, unsigned long *p_rate)
 {
 	/* Find the highest supported frequency <= rate */
 	struct mpu_rate * ptr;
@@ -324,26 +372,40 @@ static unsigned calc_ext_dsor(unsigned long rate)
 }
 
 /* XXX Only needed on 1510 */
-int omap1_set_uart_rate(struct clk *clk, unsigned long rate)
+long omap1_round_uart_rate(struct omap1_clk *clk, unsigned long rate, unsigned long *p_rate)
+{
+	return rate > 24000000 ? 48000000 : 12000000;
+}
+
+int omap1_set_uart_rate(struct omap1_clk *clk, unsigned long rate, unsigned long p_rate)
 {
+	unsigned long flags;
 	unsigned int val;
 
-	val = __raw_readl(clk->enable_reg);
 	if (rate == 12000000)
-		val &= ~(1 << clk->enable_bit);
+		val = 0;
 	else if (rate == 48000000)
-		val |= (1 << clk->enable_bit);
+		val = 1 << clk->enable_bit;
 	else
 		return -EINVAL;
+
+	/* protect MOD_CONF_CTRL_0 register from concurrent access via clk_enable/disable() */
+	spin_lock_irqsave(&mod_conf_ctrl_0_lock, flags);
+
+	val |= __raw_readl(clk->enable_reg) & ~(1 << clk->enable_bit);
 	__raw_writel(val, clk->enable_reg);
+
+	spin_unlock_irqrestore(&mod_conf_ctrl_0_lock, flags);
+
 	clk->rate = rate;
 
 	return 0;
 }
 
 /* External clock (MCLK & BCLK) functions */
-int omap1_set_ext_clk_rate(struct clk *clk, unsigned long rate)
+int omap1_set_ext_clk_rate(struct omap1_clk *clk, unsigned long rate, unsigned long p_rate)
 {
+	unsigned long flags;
 	unsigned dsor;
 	__u16 ratio_bits;
 
@@ -354,25 +416,53 @@ int omap1_set_ext_clk_rate(struct clk *clk, unsigned long rate)
 	else
 		ratio_bits = (dsor - 2) << 2;
 
+	/* protect SWD_CLK_DIV_CTRL_SEL register from concurrent access via clk_enable/disable() */
+	spin_lock_irqsave(&swd_clk_div_ctrl_sel_lock, flags);
+
 	ratio_bits |= __raw_readw(clk->enable_reg) & ~0xfd;
 	__raw_writew(ratio_bits, clk->enable_reg);
 
+	spin_unlock_irqrestore(&swd_clk_div_ctrl_sel_lock, flags);
+
 	return 0;
 }
 
-int omap1_set_sossi_rate(struct clk *clk, unsigned long rate)
+static int calc_div_sossi(unsigned long rate, unsigned long p_rate)
 {
-	u32 l;
 	int div;
-	unsigned long p_rate;
 
-	p_rate = clk->parent->rate;
 	/* Round towards slower frequency */
 	div = (p_rate + rate - 1) / rate;
-	div--;
+
+	return --div;
+}
+
+long omap1_round_sossi_rate(struct omap1_clk *clk, unsigned long rate, unsigned long *p_rate)
+{
+	int div;
+
+	div = calc_div_sossi(rate, *p_rate);
+	if (div < 0)
+		div = 0;
+	else if (div > 7)
+		div = 7;
+
+	return *p_rate / (div + 1);
+}
+
+int omap1_set_sossi_rate(struct omap1_clk *clk, unsigned long rate, unsigned long p_rate)
+{
+	unsigned long flags;
+	u32 l;
+	int div;
+
+	div = calc_div_sossi(rate, p_rate);
 	if (div < 0 || div > 7)
 		return -EINVAL;
 
+	/* protect MOD_CONF_CTRL_1 register from concurrent access via clk_enable/disable() */
+	spin_lock_irqsave(&mod_conf_ctrl_1_lock, flags);
+
 	l = omap_readl(MOD_CONF_CTRL_1);
 	l &= ~(7 << 17);
 	l |= div << 17;
@@ -380,15 +470,17 @@ int omap1_set_sossi_rate(struct clk *clk, unsigned long rate)
 
 	clk->rate = p_rate / (div + 1);
 
+	spin_unlock_irqrestore(&mod_conf_ctrl_1_lock, flags);
+
 	return 0;
 }
 
-long omap1_round_ext_clk_rate(struct clk *clk, unsigned long rate)
+long omap1_round_ext_clk_rate(struct omap1_clk *clk, unsigned long rate, unsigned long *p_rate)
 {
 	return 96000000 / calc_ext_dsor(rate);
 }
 
-void omap1_init_ext_clk(struct clk *clk)
+int omap1_init_ext_clk(struct omap1_clk *clk)
 {
 	unsigned dsor;
 	__u16 ratio_bits;
@@ -404,59 +496,59 @@ void omap1_init_ext_clk(struct clk *clk)
 		dsor = ratio_bits + 2;
 
 	clk-> rate = 96000000 / dsor;
+
+	return 0;
 }
 
-int omap1_clk_enable(struct clk *clk)
+static int omap1_clk_enable(struct clk_hw *hw)
 {
+	struct omap1_clk *clk = to_omap1_clk(hw), *parent = to_omap1_clk(clk_hw_get_parent(hw));
 	int ret = 0;
 
-	if (clk->usecount++ == 0) {
-		if (clk->parent) {
-			ret = omap1_clk_enable(clk->parent);
-			if (ret)
-				goto err;
-
-			if (clk->flags & CLOCK_NO_IDLE_PARENT)
-				omap1_clk_deny_idle(clk->parent);
-		}
+	if (parent && clk->flags & CLOCK_NO_IDLE_PARENT)
+		omap1_clk_deny_idle(parent);
 
+	if (clk->ops && !(WARN_ON(!clk->ops->enable)))
 		ret = clk->ops->enable(clk);
-		if (ret) {
-			if (clk->parent)
-				omap1_clk_disable(clk->parent);
-			goto err;
-		}
-	}
-	return ret;
 
-err:
-	clk->usecount--;
 	return ret;
 }
 
-void omap1_clk_disable(struct clk *clk)
+static void omap1_clk_disable(struct clk_hw *hw)
 {
-	if (clk->usecount > 0 && !(--clk->usecount)) {
+	struct omap1_clk *clk = to_omap1_clk(hw), *parent = to_omap1_clk(clk_hw_get_parent(hw));
+
+	if (clk->ops && !(WARN_ON(!clk->ops->disable)))
 		clk->ops->disable(clk);
-		if (likely(clk->parent)) {
-			omap1_clk_disable(clk->parent);
-			if (clk->flags & CLOCK_NO_IDLE_PARENT)
-				omap1_clk_allow_idle(clk->parent);
-		}
-	}
+
+	if (likely(parent) && clk->flags & CLOCK_NO_IDLE_PARENT)
+		omap1_clk_allow_idle(parent);
 }
 
-static int omap1_clk_enable_generic(struct clk *clk)
+static int omap1_clk_enable_generic(struct omap1_clk *clk)
 {
+	unsigned long flags;
 	__u16 regval16;
 	__u32 regval32;
 
 	if (unlikely(clk->enable_reg == NULL)) {
 		printk(KERN_ERR "clock.c: Enable for %s without enable code\n",
-		       clk->name);
+		       clk_hw_get_name(&clk->hw));
 		return -EINVAL;
 	}
 
+	/* protect clk->enable_reg from concurrent access via clk_set_rate() */
+	if (clk->enable_reg == OMAP1_IO_ADDRESS(ARM_CKCTL))
+		spin_lock_irqsave(&arm_ckctl_lock, flags);
+	else if (clk->enable_reg == OMAP1_IO_ADDRESS(ARM_IDLECT2))
+		spin_lock_irqsave(&arm_idlect2_lock, flags);
+	else if (clk->enable_reg == OMAP1_IO_ADDRESS(MOD_CONF_CTRL_0))
+		spin_lock_irqsave(&mod_conf_ctrl_0_lock, flags);
+	else if (clk->enable_reg == OMAP1_IO_ADDRESS(MOD_CONF_CTRL_1))
+		spin_lock_irqsave(&mod_conf_ctrl_1_lock, flags);
+	else if (clk->enable_reg == OMAP1_IO_ADDRESS(SWD_CLK_DIV_CTRL_SEL))
+		spin_lock_irqsave(&swd_clk_div_ctrl_sel_lock, flags);
+
 	if (clk->flags & ENABLE_REG_32BIT) {
 		regval32 = __raw_readl(clk->enable_reg);
 		regval32 |= (1 << clk->enable_bit);
@@ -467,17 +559,41 @@ static int omap1_clk_enable_generic(struct clk *clk)
 		__raw_writew(regval16, clk->enable_reg);
 	}
 
+	if (clk->enable_reg == OMAP1_IO_ADDRESS(ARM_CKCTL))
+		spin_unlock_irqrestore(&arm_ckctl_lock, flags);
+	else if (clk->enable_reg == OMAP1_IO_ADDRESS(ARM_IDLECT2))
+		spin_unlock_irqrestore(&arm_idlect2_lock, flags);
+	else if (clk->enable_reg == OMAP1_IO_ADDRESS(MOD_CONF_CTRL_0))
+		spin_unlock_irqrestore(&mod_conf_ctrl_0_lock, flags);
+	else if (clk->enable_reg == OMAP1_IO_ADDRESS(MOD_CONF_CTRL_1))
+		spin_unlock_irqrestore(&mod_conf_ctrl_1_lock, flags);
+	else if (clk->enable_reg == OMAP1_IO_ADDRESS(SWD_CLK_DIV_CTRL_SEL))
+		spin_unlock_irqrestore(&swd_clk_div_ctrl_sel_lock, flags);
+
 	return 0;
 }
 
-static void omap1_clk_disable_generic(struct clk *clk)
+static void omap1_clk_disable_generic(struct omap1_clk *clk)
 {
+	unsigned long flags;
 	__u16 regval16;
 	__u32 regval32;
 
 	if (clk->enable_reg == NULL)
 		return;
 
+	/* protect clk->enable_reg from concurrent access via clk_set_rate() */
+	if (clk->enable_reg == OMAP1_IO_ADDRESS(ARM_CKCTL))
+		spin_lock_irqsave(&arm_ckctl_lock, flags);
+	else if (clk->enable_reg == OMAP1_IO_ADDRESS(ARM_IDLECT2))
+		spin_lock_irqsave(&arm_idlect2_lock, flags);
+	else if (clk->enable_reg == OMAP1_IO_ADDRESS(MOD_CONF_CTRL_0))
+		spin_lock_irqsave(&mod_conf_ctrl_0_lock, flags);
+	else if (clk->enable_reg == OMAP1_IO_ADDRESS(MOD_CONF_CTRL_1))
+		spin_lock_irqsave(&mod_conf_ctrl_1_lock, flags);
+	else if (clk->enable_reg == OMAP1_IO_ADDRESS(SWD_CLK_DIV_CTRL_SEL))
+		spin_lock_irqsave(&swd_clk_div_ctrl_sel_lock, flags);
+
 	if (clk->flags & ENABLE_REG_32BIT) {
 		regval32 = __raw_readl(clk->enable_reg);
 		regval32 &= ~(1 << clk->enable_bit);
@@ -487,6 +603,17 @@ static void omap1_clk_disable_generic(struct clk *clk)
 		regval16 &= ~(1 << clk->enable_bit);
 		__raw_writew(regval16, clk->enable_reg);
 	}
+
+	if (clk->enable_reg == OMAP1_IO_ADDRESS(ARM_CKCTL))
+		spin_unlock_irqrestore(&arm_ckctl_lock, flags);
+	else if (clk->enable_reg == OMAP1_IO_ADDRESS(ARM_IDLECT2))
+		spin_unlock_irqrestore(&arm_idlect2_lock, flags);
+	else if (clk->enable_reg == OMAP1_IO_ADDRESS(MOD_CONF_CTRL_0))
+		spin_unlock_irqrestore(&mod_conf_ctrl_0_lock, flags);
+	else if (clk->enable_reg == OMAP1_IO_ADDRESS(MOD_CONF_CTRL_1))
+		spin_unlock_irqrestore(&mod_conf_ctrl_1_lock, flags);
+	else if (clk->enable_reg == OMAP1_IO_ADDRESS(SWD_CLK_DIV_CTRL_SEL))
+		spin_unlock_irqrestore(&swd_clk_div_ctrl_sel_lock, flags);
 }
 
 const struct clkops clkops_generic = {
@@ -494,25 +621,38 @@ const struct clkops clkops_generic = {
 	.disable	= omap1_clk_disable_generic,
 };
 
-static int omap1_clk_enable_dsp_domain(struct clk *clk)
+static int omap1_clk_enable_dsp_domain(struct omap1_clk *clk)
 {
-	int retval;
+	bool api_ck_was_enabled;
+	int retval = 0;
+
+	api_ck_was_enabled = omap1_clk_is_enabled(&api_ck_p->hw);
+	if (!api_ck_was_enabled)
+		retval = api_ck_p->ops->enable(api_ck_p);
 
-	retval = omap1_clk_enable(api_ck_p);
 	if (!retval) {
 		retval = omap1_clk_enable_generic(clk);
-		omap1_clk_disable(api_ck_p);
+
+		if (!api_ck_was_enabled)
+			api_ck_p->ops->disable(api_ck_p);
 	}
 
 	return retval;
 }
 
-static void omap1_clk_disable_dsp_domain(struct clk *clk)
+static void omap1_clk_disable_dsp_domain(struct omap1_clk *clk)
 {
-	if (omap1_clk_enable(api_ck_p) == 0) {
-		omap1_clk_disable_generic(clk);
-		omap1_clk_disable(api_ck_p);
-	}
+	bool api_ck_was_enabled;
+
+	api_ck_was_enabled = omap1_clk_is_enabled(&api_ck_p->hw);
+	if (!api_ck_was_enabled)
+		if (api_ck_p->ops->enable(api_ck_p) < 0)
+			return;
+
+	omap1_clk_disable_generic(clk);
+
+	if (!api_ck_was_enabled)
+		api_ck_p->ops->disable(api_ck_p);
 }
 
 const struct clkops clkops_dspck = {
@@ -521,7 +661,7 @@ const struct clkops clkops_dspck = {
 };
 
 /* XXX SYSC register handling does not belong in the clock framework */
-static int omap1_clk_enable_uart_functional_16xx(struct clk *clk)
+static int omap1_clk_enable_uart_functional_16xx(struct omap1_clk *clk)
 {
 	int ret;
 	struct uart_clk *uclk;
@@ -538,7 +678,7 @@ static int omap1_clk_enable_uart_functional_16xx(struct clk *clk)
 }
 
 /* XXX SYSC register handling does not belong in the clock framework */
-static void omap1_clk_disable_uart_functional_16xx(struct clk *clk)
+static void omap1_clk_disable_uart_functional_16xx(struct omap1_clk *clk)
 {
 	struct uart_clk *uclk;
 
@@ -555,20 +695,33 @@ const struct clkops clkops_uart_16xx = {
 	.disable	= omap1_clk_disable_uart_functional_16xx,
 };
 
-long omap1_clk_round_rate(struct clk *clk, unsigned long rate)
+static unsigned long omap1_clk_recalc_rate(struct clk_hw *hw, unsigned long p_rate)
 {
-	if (clk->round_rate != NULL)
-		return clk->round_rate(clk, rate);
+	struct omap1_clk *clk = to_omap1_clk(hw);
+
+	if (clk->recalc)
+		return clk->recalc(clk, p_rate);
 
 	return clk->rate;
 }
 
-int omap1_clk_set_rate(struct clk *clk, unsigned long rate)
+static long omap1_clk_round_rate(struct clk_hw *hw, unsigned long rate, unsigned long *p_rate)
+{
+	struct omap1_clk *clk = to_omap1_clk(hw);
+
+	if (clk->round_rate != NULL)
+		return clk->round_rate(clk, rate, p_rate);
+
+	return omap1_clk_recalc_rate(hw, *p_rate);
+}
+
+static int omap1_clk_set_rate(struct clk_hw *hw, unsigned long rate, unsigned long p_rate)
 {
+	struct omap1_clk *clk = to_omap1_clk(hw);
 	int  ret = -EINVAL;
 
 	if (clk->set_rate)
-		ret = clk->set_rate(clk, rate);
+		ret = clk->set_rate(clk, rate, p_rate);
 	return ret;
 }
 
@@ -576,340 +729,105 @@ int omap1_clk_set_rate(struct clk *clk, unsigned long rate)
  * Omap1 clock reset and init functions
  */
 
+static int omap1_clk_init_op(struct clk_hw *hw)
+{
+	struct omap1_clk *clk = to_omap1_clk(hw);
+
+	if (clk->init)
+		return clk->init(clk);
+
+	return 0;
+}
+
 #ifdef CONFIG_OMAP_RESET_CLOCKS
 
-void omap1_clk_disable_unused(struct clk *clk)
+static void omap1_clk_disable_unused(struct clk_hw *hw)
 {
-	__u32 regval32;
+	struct omap1_clk *clk = to_omap1_clk(hw);
+	const char *name = clk_hw_get_name(hw);
 
 	/* Clocks in the DSP domain need api_ck. Just assume bootloader
 	 * has not enabled any DSP clocks */
 	if (clk->enable_reg == DSP_IDLECT2) {
-		pr_info("Skipping reset check for DSP domain clock \"%s\"\n",
-			clk->name);
+		pr_info("Skipping reset check for DSP domain clock \"%s\"\n", name);
 		return;
 	}
 
-	/* Is the clock already disabled? */
-	if (clk->flags & ENABLE_REG_32BIT)
-		regval32 = __raw_readl(clk->enable_reg);
-	else
-		regval32 = __raw_readw(clk->enable_reg);
-
-	if ((regval32 & (1 << clk->enable_bit)) == 0)
-		return;
-
-	printk(KERN_INFO "Disabling unused clock \"%s\"... ", clk->name);
-	clk->ops->disable(clk);
+	pr_info("Disabling unused clock \"%s\"... ", name);
+	omap1_clk_disable(hw);
 	printk(" done\n");
 }
 
 #endif
 
+const struct clk_ops omap1_clk_gate_ops = {
+	.enable		= omap1_clk_enable,
+	.disable	= omap1_clk_disable,
+	.is_enabled	= omap1_clk_is_enabled,
+#ifdef CONFIG_OMAP_RESET_CLOCKS
+	.disable_unused	= omap1_clk_disable_unused,
+#endif
+};
 
-int clk_enable(struct clk *clk)
-{
-	unsigned long flags;
-	int ret;
-
-	if (IS_ERR_OR_NULL(clk))
-		return -EINVAL;
-
-	spin_lock_irqsave(&clockfw_lock, flags);
-	ret = omap1_clk_enable(clk);
-	spin_unlock_irqrestore(&clockfw_lock, flags);
-
-	return ret;
-}
-EXPORT_SYMBOL(clk_enable);
-
-void clk_disable(struct clk *clk)
-{
-	unsigned long flags;
-
-	if (IS_ERR_OR_NULL(clk))
-		return;
-
-	spin_lock_irqsave(&clockfw_lock, flags);
-	if (clk->usecount == 0) {
-		pr_err("Trying disable clock %s with 0 usecount\n",
-		       clk->name);
-		WARN_ON(1);
-		goto out;
-	}
-
-	omap1_clk_disable(clk);
-
-out:
-	spin_unlock_irqrestore(&clockfw_lock, flags);
-}
-EXPORT_SYMBOL(clk_disable);
-
-unsigned long clk_get_rate(struct clk *clk)
-{
-	unsigned long flags;
-	unsigned long ret;
-
-	if (IS_ERR_OR_NULL(clk))
-		return 0;
-
-	spin_lock_irqsave(&clockfw_lock, flags);
-	ret = clk->rate;
-	spin_unlock_irqrestore(&clockfw_lock, flags);
-
-	return ret;
-}
-EXPORT_SYMBOL(clk_get_rate);
-
-/*
- * Optional clock functions defined in include/linux/clk.h
- */
-
-long clk_round_rate(struct clk *clk, unsigned long rate)
-{
-	unsigned long flags;
-	long ret;
-
-	if (IS_ERR_OR_NULL(clk))
-		return 0;
-
-	spin_lock_irqsave(&clockfw_lock, flags);
-	ret = omap1_clk_round_rate(clk, rate);
-	spin_unlock_irqrestore(&clockfw_lock, flags);
-
-	return ret;
-}
-EXPORT_SYMBOL(clk_round_rate);
-
-int clk_set_rate(struct clk *clk, unsigned long rate)
-{
-	unsigned long flags;
-	int ret = -EINVAL;
-
-	if (IS_ERR_OR_NULL(clk))
-		return ret;
-
-	spin_lock_irqsave(&clockfw_lock, flags);
-	ret = omap1_clk_set_rate(clk, rate);
-	if (ret == 0)
-		propagate_rate(clk);
-	spin_unlock_irqrestore(&clockfw_lock, flags);
-
-	return ret;
-}
-EXPORT_SYMBOL(clk_set_rate);
-
-int clk_set_parent(struct clk *clk, struct clk *parent)
-{
-	WARN_ONCE(1, "clk_set_parent() not implemented for OMAP1\n");
-
-	return -EINVAL;
-}
-EXPORT_SYMBOL(clk_set_parent);
+const struct clk_ops omap1_clk_rate_ops = {
+	.recalc_rate	= omap1_clk_recalc_rate,
+	.round_rate	= omap1_clk_round_rate,
+	.set_rate	= omap1_clk_set_rate,
+	.init		= omap1_clk_init_op,
+};
 
-struct clk *clk_get_parent(struct clk *clk)
-{
-	return clk->parent;
-}
-EXPORT_SYMBOL(clk_get_parent);
+const struct clk_ops omap1_clk_full_ops = {
+	.enable		= omap1_clk_enable,
+	.disable	= omap1_clk_disable,
+	.is_enabled	= omap1_clk_is_enabled,
+#ifdef CONFIG_OMAP_RESET_CLOCKS
+	.disable_unused	= omap1_clk_disable_unused,
+#endif
+	.recalc_rate	= omap1_clk_recalc_rate,
+	.round_rate	= omap1_clk_round_rate,
+	.set_rate	= omap1_clk_set_rate,
+	.init		= omap1_clk_init_op,
+};
 
 /*
  * OMAP specific clock functions shared between omap1 and omap2
  */
 
 /* Used for clocks that always have same value as the parent clock */
-unsigned long followparent_recalc(struct clk *clk)
+unsigned long followparent_recalc(struct omap1_clk *clk, unsigned long p_rate)
 {
-	return clk->parent->rate;
+	return p_rate;
 }
 
 /*
  * Used for clocks that have the same value as the parent clock,
  * divided by some factor
  */
-unsigned long omap_fixed_divisor_recalc(struct clk *clk)
+unsigned long omap_fixed_divisor_recalc(struct omap1_clk *clk, unsigned long p_rate)
 {
 	WARN_ON(!clk->fixed_div);
 
-	return clk->parent->rate / clk->fixed_div;
-}
-
-void clk_reparent(struct clk *child, struct clk *parent)
-{
-	list_del_init(&child->sibling);
-	if (parent)
-		list_add(&child->sibling, &parent->children);
-	child->parent = parent;
-
-	/* now do the debugfs renaming to reattach the child
-	   to the proper parent */
+	return p_rate / clk->fixed_div;
 }
 
 /* Propagate rate to children */
-void propagate_rate(struct clk *tclk)
-{
-	struct clk *clkp;
-
-	list_for_each_entry(clkp, &tclk->children, sibling) {
-		if (clkp->recalc)
-			clkp->rate = clkp->recalc(clkp);
-		propagate_rate(clkp);
-	}
-}
-
-static LIST_HEAD(root_clks);
-
-/**
- * recalculate_root_clocks - recalculate and propagate all root clocks
- *
- * Recalculates all root clocks (clocks with no parent), which if the
- * clock's .recalc is set correctly, should also propagate their rates.
- * Called at init.
- */
-void recalculate_root_clocks(void)
+void propagate_rate(struct omap1_clk *tclk)
 {
 	struct clk *clkp;
 
-	list_for_each_entry(clkp, &root_clks, sibling) {
-		if (clkp->recalc)
-			clkp->rate = clkp->recalc(clkp);
-		propagate_rate(clkp);
-	}
-}
-
-/**
- * clk_preinit - initialize any fields in the struct clk before clk init
- * @clk: struct clk * to initialize
- *
- * Initialize any struct clk fields needed before normal clk initialization
- * can run.  No return value.
- */
-void clk_preinit(struct clk *clk)
-{
-	INIT_LIST_HEAD(&clk->children);
-}
-
-int clk_register(struct clk *clk)
-{
-	if (IS_ERR_OR_NULL(clk))
-		return -EINVAL;
-
-	/*
-	 * trap out already registered clocks
-	 */
-	if (clk->node.next || clk->node.prev)
-		return 0;
-
-	mutex_lock(&clocks_mutex);
-	if (clk->parent)
-		list_add(&clk->sibling, &clk->parent->children);
-	else
-		list_add(&clk->sibling, &root_clks);
-
-	list_add(&clk->node, &clocks);
-	if (clk->init)
-		clk->init(clk);
-	mutex_unlock(&clocks_mutex);
-
-	return 0;
-}
-EXPORT_SYMBOL(clk_register);
-
-void clk_unregister(struct clk *clk)
-{
-	if (IS_ERR_OR_NULL(clk))
+	/* depend on CCF ability to recalculate new rates across whole clock subtree */
+	if (WARN_ON(!(clk_hw_get_flags(&tclk->hw) & CLK_GET_RATE_NOCACHE)))
 		return;
 
-	mutex_lock(&clocks_mutex);
-	list_del(&clk->sibling);
-	list_del(&clk->node);
-	mutex_unlock(&clocks_mutex);
-}
-EXPORT_SYMBOL(clk_unregister);
-
-void clk_enable_init_clocks(void)
-{
-	struct clk *clkp;
-
-	list_for_each_entry(clkp, &clocks, node)
-		if (clkp->flags & ENABLE_ON_INIT)
-			clk_enable(clkp);
-}
-
-/**
- * omap_clk_get_by_name - locate OMAP struct clk by its name
- * @name: name of the struct clk to locate
- *
- * Locate an OMAP struct clk by its name.  Assumes that struct clk
- * names are unique.  Returns NULL if not found or a pointer to the
- * struct clk if found.
- */
-struct clk *omap_clk_get_by_name(const char *name)
-{
-	struct clk *c;
-	struct clk *ret = NULL;
-
-	mutex_lock(&clocks_mutex);
-
-	list_for_each_entry(c, &clocks, node) {
-		if (!strcmp(c->name, name)) {
-			ret = c;
-			break;
-		}
-	}
-
-	mutex_unlock(&clocks_mutex);
-
-	return ret;
-}
-
-int omap_clk_enable_autoidle_all(void)
-{
-	struct clk *c;
-	unsigned long flags;
-
-	spin_lock_irqsave(&clockfw_lock, flags);
-
-	list_for_each_entry(c, &clocks, node)
-		if (c->ops->allow_idle)
-			c->ops->allow_idle(c);
-
-	spin_unlock_irqrestore(&clockfw_lock, flags);
-
-	return 0;
-}
-
-int omap_clk_disable_autoidle_all(void)
-{
-	struct clk *c;
-	unsigned long flags;
-
-	spin_lock_irqsave(&clockfw_lock, flags);
-
-	list_for_each_entry(c, &clocks, node)
-		if (c->ops->deny_idle)
-			c->ops->deny_idle(c);
-
-	spin_unlock_irqrestore(&clockfw_lock, flags);
-
-	return 0;
-}
-
-/*
- * Low level helpers
- */
-static int clkll_enable_null(struct clk *clk)
-{
-	return 0;
-}
+	clkp = clk_get_sys(NULL, clk_hw_get_name(&tclk->hw));
+	if (WARN_ON(!clkp))
+		return;
 
-static void clkll_disable_null(struct clk *clk)
-{
+	clk_get_rate(clkp);
+	clk_put(clkp);
 }
 
-const struct clkops clkops_null = {
-	.enable		= clkll_enable_null,
-	.disable	= clkll_disable_null,
+const struct clk_ops omap1_clk_null_ops = {
 };
 
 /*
@@ -917,115 +835,6 @@ const struct clkops clkops_null = {
  *
  * Used for clock aliases that are needed on some OMAPs, but not others
  */
-struct clk dummy_ck = {
-	.name	= "dummy",
-	.ops	= &clkops_null,
+struct omap1_clk dummy_ck __refdata = {
+	.hw.init	= CLK_HW_INIT_NO_PARENT("dummy", &omap1_clk_null_ops, 0),
 };
-
-/*
- *
- */
-
-#ifdef CONFIG_OMAP_RESET_CLOCKS
-/*
- * Disable any unused clocks left on by the bootloader
- */
-static int __init clk_disable_unused(void)
-{
-	struct clk *ck;
-	unsigned long flags;
-
-	pr_info("clock: disabling unused clocks to save power\n");
-
-	spin_lock_irqsave(&clockfw_lock, flags);
-	list_for_each_entry(ck, &clocks, node) {
-		if (ck->ops == &clkops_null)
-			continue;
-
-		if (ck->usecount > 0 || !ck->enable_reg)
-			continue;
-
-		omap1_clk_disable_unused(ck);
-	}
-	spin_unlock_irqrestore(&clockfw_lock, flags);
-
-	return 0;
-}
-late_initcall(clk_disable_unused);
-late_initcall(omap_clk_enable_autoidle_all);
-#endif
-
-#if defined(CONFIG_PM_DEBUG) && defined(CONFIG_DEBUG_FS)
-/*
- *	debugfs support to trace clock tree hierarchy and attributes
- */
-
-#include <linux/debugfs.h>
-#include <linux/seq_file.h>
-
-static struct dentry *clk_debugfs_root;
-
-static int debug_clock_show(struct seq_file *s, void *unused)
-{
-	struct clk *c;
-	struct clk *pa;
-
-	mutex_lock(&clocks_mutex);
-	seq_printf(s, "%-30s %-30s %-10s %s\n",
-		   "clock-name", "parent-name", "rate", "use-count");
-
-	list_for_each_entry(c, &clocks, node) {
-		pa = c->parent;
-		seq_printf(s, "%-30s %-30s %-10lu %d\n",
-			   c->name, pa ? pa->name : "none", c->rate,
-			   c->usecount);
-	}
-	mutex_unlock(&clocks_mutex);
-
-	return 0;
-}
-
-DEFINE_SHOW_ATTRIBUTE(debug_clock);
-
-static void clk_debugfs_register_one(struct clk *c)
-{
-	struct dentry *d;
-	struct clk *pa = c->parent;
-
-	d = debugfs_create_dir(c->name, pa ? pa->dent : clk_debugfs_root);
-	c->dent = d;
-
-	debugfs_create_u8("usecount", S_IRUGO, c->dent, &c->usecount);
-	debugfs_create_ulong("rate", S_IRUGO, c->dent, &c->rate);
-	debugfs_create_x8("flags", S_IRUGO, c->dent, &c->flags);
-}
-
-static void clk_debugfs_register(struct clk *c)
-{
-	struct clk *pa = c->parent;
-
-	if (pa && !pa->dent)
-		clk_debugfs_register(pa);
-
-	if (!c->dent)
-		clk_debugfs_register_one(c);
-}
-
-static int __init clk_debugfs_init(void)
-{
-	struct clk *c;
-	struct dentry *d;
-
-	d = debugfs_create_dir("clock", NULL);
-	clk_debugfs_root = d;
-
-	list_for_each_entry(c, &clocks, node)
-		clk_debugfs_register(c);
-
-	debugfs_create_file("summary", S_IRUGO, d, NULL, &debug_clock_fops);
-
-	return 0;
-}
-late_initcall(clk_debugfs_init);
-
-#endif /* defined(CONFIG_PM_DEBUG) && defined(CONFIG_DEBUG_FS) */
diff --git a/arch/arm/mach-omap1/clock.h b/arch/arm/mach-omap1/clock.h
index f3b8811f5ac0..16cfb2e86ee4 100644
--- a/arch/arm/mach-omap1/clock.h
+++ b/arch/arm/mach-omap1/clock.h
@@ -11,12 +11,11 @@
 #define __ARCH_ARM_MACH_OMAP1_CLOCK_H
 
 #include <linux/clk.h>
-#include <linux/list.h>
-
 #include <linux/clkdev.h>
+#include <linux/clk-provider.h>
 
 struct module;
-struct clk;
+struct omap1_clk;
 
 struct omap_clk {
 	u16				cpu;
@@ -29,7 +28,7 @@ struct omap_clk {
 		.lk = {			\
 			.dev_id = dev,	\
 			.con_id = con,	\
-			.clk = ck,	\
+			.clk_hw = ck,	\
 		},			\
 	}
 
@@ -40,68 +39,30 @@ struct omap_clk {
 #define CK_16XX		(1 << 3)	/* 16xx, 17xx, 5912 */
 #define CK_1710		(1 << 4)	/* 1710 extra for rate selection */
 
-
-/* Temporary, needed during the common clock framework conversion */
-#define __clk_get_name(clk)	(clk->name)
-#define __clk_get_parent(clk)	(clk->parent)
-#define __clk_get_rate(clk)	(clk->rate)
-
 /**
  * struct clkops - some clock function pointers
  * @enable: fn ptr that enables the current clock in hardware
  * @disable: fn ptr that enables the current clock in hardware
- * @find_idlest: function returning the IDLEST register for the clock's IP blk
- * @find_companion: function returning the "companion" clk reg for the clock
  * @allow_idle: fn ptr that enables autoidle for the current clock in hardware
- * @deny_idle: fn ptr that disables autoidle for the current clock in hardware
- *
- * A "companion" clk is an accompanying clock to the one being queried
- * that must be enabled for the IP module connected to the clock to
- * become accessible by the hardware.  Neither @find_idlest nor
- * @find_companion should be needed; that information is IP
- * block-specific; the hwmod code has been created to handle this, but
- * until hwmod data is ready and drivers have been converted to use PM
- * runtime calls in place of clk_enable()/clk_disable(), @find_idlest and
- * @find_companion must, unfortunately, remain.
  */
 struct clkops {
-	int			(*enable)(struct clk *);
-	void			(*disable)(struct clk *);
-	void			(*find_idlest)(struct clk *, void __iomem **,
-					       u8 *, u8 *);
-	void			(*find_companion)(struct clk *, void __iomem **,
-						  u8 *);
-	void			(*allow_idle)(struct clk *);
-	void			(*deny_idle)(struct clk *);
+	int			(*enable)(struct omap1_clk *clk);
+	void			(*disable)(struct omap1_clk *clk);
 };
 
 /*
  * struct clk.flags possibilities
  *
  * XXX document the rest of the clock flags here
- *
- * CLOCK_CLKOUTX2: (OMAP4 only) DPLL CLKOUT and CLKOUTX2 GATE_CTRL
- *     bits share the same register.  This flag allows the
- *     omap4_dpllmx*() code to determine which GATE_CTRL bit field
- *     should be used.  This is a temporary solution - a better approach
- *     would be to associate clock type-specific data with the clock,
- *     similar to the struct dpll_data approach.
  */
 #define ENABLE_REG_32BIT	(1 << 0)	/* Use 32-bit access */
 #define CLOCK_IDLE_CONTROL	(1 << 1)
 #define CLOCK_NO_IDLE_PARENT	(1 << 2)
-#define ENABLE_ON_INIT		(1 << 3)	/* Enable upon framework init */
-#define INVERT_ENABLE		(1 << 4)	/* 0 enables, 1 disables */
-#define CLOCK_CLKOUTX2		(1 << 5)
 
 /**
- * struct clk - OMAP struct clk
- * @node: list_head connecting this clock into the full clock list
+ * struct omap1_clk - OMAP1 struct clk
+ * @hw: struct clk_hw for common clock framework integration
  * @ops: struct clkops * for this clock
- * @name: the name of the clock in the hardware (used in hwmod data and debug)
- * @parent: pointer to this clock's parent struct clk
- * @children: list_head connecting to the child clks' @sibling list_heads
- * @sibling: list_head connecting this clk to its parent clk's @children
  * @rate: current clock rate
  * @enable_reg: register to write to enable the clock (see @enable_bit)
  * @recalc: fn ptr that returns the clock's current rate
@@ -109,123 +70,65 @@ struct clkops {
  * @round_rate: fn ptr that can round the clock's current rate
  * @init: fn ptr to do clock-specific initialization
  * @enable_bit: bitshift to write to enable/disable the clock (see @enable_reg)
- * @usecount: number of users that have requested this clock to be enabled
  * @fixed_div: when > 0, this clock's rate is its parent's rate / @fixed_div
  * @flags: see "struct clk.flags possibilities" above
  * @rate_offset: bitshift for rate selection bitfield (OMAP1 only)
- * @src_offset: bitshift for source selection bitfield (OMAP1 only)
- *
- * XXX @rate_offset, @src_offset should probably be removed and OMAP1
- * clock code converted to use clksel.
- *
- * XXX @usecount is poorly named.  It should be "enable_count" or
- * something similar.  "users" in the description refers to kernel
- * code (core code or drivers) that have called clk_enable() and not
- * yet called clk_disable(); the usecount of parent clocks is also
- * incremented by the clock code when clk_enable() is called on child
- * clocks and decremented by the clock code when clk_disable() is
- * called on child clocks.
- *
- * XXX @clkdm, @usecount, @children, @sibling should be marked for
- * internal use only.
- *
- * @children and @sibling are used to optimize parent-to-child clock
- * tree traversals.  (child-to-parent traversals use @parent.)
- *
- * XXX The notion of the clock's current rate probably needs to be
- * separated from the clock's target rate.
  */
-struct clk {
-	struct list_head	node;
+struct omap1_clk {
+	struct clk_hw		hw;
 	const struct clkops	*ops;
-	const char		*name;
-	struct clk		*parent;
-	struct list_head	children;
-	struct list_head	sibling;	/* node for children */
 	unsigned long		rate;
 	void __iomem		*enable_reg;
-	unsigned long		(*recalc)(struct clk *);
-	int			(*set_rate)(struct clk *, unsigned long);
-	long			(*round_rate)(struct clk *, unsigned long);
-	void			(*init)(struct clk *);
+	unsigned long		(*recalc)(struct omap1_clk *clk, unsigned long rate);
+	int			(*set_rate)(struct omap1_clk *clk, unsigned long rate,
+					    unsigned long p_rate);
+	long			(*round_rate)(struct omap1_clk *clk, unsigned long rate,
+					      unsigned long *p_rate);
+	int			(*init)(struct omap1_clk *clk);
 	u8			enable_bit;
-	s8			usecount;
 	u8			fixed_div;
 	u8			flags;
 	u8			rate_offset;
-	u8			src_offset;
-#if defined(CONFIG_PM_DEBUG) && defined(CONFIG_DEBUG_FS)
-	struct dentry		*dent;	/* For visible tree hierarchy */
-#endif
-};
-
-struct clk_functions {
-	int		(*clk_enable)(struct clk *clk);
-	void		(*clk_disable)(struct clk *clk);
-	long		(*clk_round_rate)(struct clk *clk, unsigned long rate);
-	int		(*clk_set_rate)(struct clk *clk, unsigned long rate);
-	int		(*clk_set_parent)(struct clk *clk, struct clk *parent);
-	void		(*clk_allow_idle)(struct clk *clk);
-	void		(*clk_deny_idle)(struct clk *clk);
-	void		(*clk_disable_unused)(struct clk *clk);
 };
+#define to_omap1_clk(_hw)	container_of(_hw, struct omap1_clk, hw)
 
-extern int clk_init(struct clk_functions *custom_clocks);
-extern void clk_preinit(struct clk *clk);
-extern int clk_register(struct clk *clk);
-extern void clk_reparent(struct clk *child, struct clk *parent);
-extern void clk_unregister(struct clk *clk);
-extern void propagate_rate(struct clk *clk);
-extern void recalculate_root_clocks(void);
-extern unsigned long followparent_recalc(struct clk *clk);
-extern void clk_enable_init_clocks(void);
-unsigned long omap_fixed_divisor_recalc(struct clk *clk);
-extern struct clk *omap_clk_get_by_name(const char *name);
-extern int omap_clk_enable_autoidle_all(void);
-extern int omap_clk_disable_autoidle_all(void);
+void propagate_rate(struct omap1_clk *clk);
+unsigned long followparent_recalc(struct omap1_clk *clk, unsigned long p_rate);
+unsigned long omap_fixed_divisor_recalc(struct omap1_clk *clk, unsigned long p_rate);
 
-extern const struct clkops clkops_null;
-
-extern struct clk dummy_ck;
+extern struct omap1_clk dummy_ck;
 
 int omap1_clk_init(void);
 void omap1_clk_late_init(void);
-extern int omap1_clk_enable(struct clk *clk);
-extern void omap1_clk_disable(struct clk *clk);
-extern long omap1_clk_round_rate(struct clk *clk, unsigned long rate);
-extern int omap1_clk_set_rate(struct clk *clk, unsigned long rate);
-extern unsigned long omap1_ckctl_recalc(struct clk *clk);
-extern int omap1_set_sossi_rate(struct clk *clk, unsigned long rate);
-extern unsigned long omap1_sossi_recalc(struct clk *clk);
-extern unsigned long omap1_ckctl_recalc_dsp_domain(struct clk *clk);
-extern int omap1_clk_set_rate_dsp_domain(struct clk *clk, unsigned long rate);
-extern int omap1_set_uart_rate(struct clk *clk, unsigned long rate);
-extern unsigned long omap1_uart_recalc(struct clk *clk);
-extern int omap1_set_ext_clk_rate(struct clk *clk, unsigned long rate);
-extern long omap1_round_ext_clk_rate(struct clk *clk, unsigned long rate);
-extern void omap1_init_ext_clk(struct clk *clk);
-extern int omap1_select_table_rate(struct clk *clk, unsigned long rate);
-extern long omap1_round_to_table_rate(struct clk *clk, unsigned long rate);
-extern int omap1_clk_set_rate_ckctl_arm(struct clk *clk, unsigned long rate);
-extern long omap1_clk_round_rate_ckctl_arm(struct clk *clk, unsigned long rate);
-extern unsigned long omap1_watchdog_recalc(struct clk *clk);
-
-#ifdef CONFIG_OMAP_RESET_CLOCKS
-extern void omap1_clk_disable_unused(struct clk *clk);
-#else
-#define omap1_clk_disable_unused	NULL
-#endif
+unsigned long omap1_ckctl_recalc(struct omap1_clk *clk, unsigned long p_rate);
+long omap1_round_sossi_rate(struct omap1_clk *clk, unsigned long rate, unsigned long *p_rate);
+int omap1_set_sossi_rate(struct omap1_clk *clk, unsigned long rate, unsigned long p_rate);
+unsigned long omap1_sossi_recalc(struct omap1_clk *clk, unsigned long p_rate);
+unsigned long omap1_ckctl_recalc_dsp_domain(struct omap1_clk *clk, unsigned long p_rate);
+int omap1_clk_set_rate_dsp_domain(struct omap1_clk *clk, unsigned long rate,
+				  unsigned long p_rate);
+long omap1_round_uart_rate(struct omap1_clk *clk, unsigned long rate, unsigned long *p_rate);
+int omap1_set_uart_rate(struct omap1_clk *clk, unsigned long rate, unsigned long p_rate);
+unsigned long omap1_uart_recalc(struct omap1_clk *clk, unsigned long p_rate);
+int omap1_set_ext_clk_rate(struct omap1_clk *clk, unsigned long rate, unsigned long p_rate);
+long omap1_round_ext_clk_rate(struct omap1_clk *clk, unsigned long rate, unsigned long *p_rate);
+int omap1_init_ext_clk(struct omap1_clk *clk);
+int omap1_select_table_rate(struct omap1_clk *clk, unsigned long rate, unsigned long p_rate);
+long omap1_round_to_table_rate(struct omap1_clk *clk, unsigned long rate, unsigned long *p_rate);
+int omap1_clk_set_rate_ckctl_arm(struct omap1_clk *clk, unsigned long rate, unsigned long p_rate);
+long omap1_clk_round_rate_ckctl_arm(struct omap1_clk *clk, unsigned long rate,
+				    unsigned long *p_rate);
 
 struct uart_clk {
-	struct clk	clk;
-	unsigned long	sysc_addr;
+	struct omap1_clk	clk;
+	unsigned long		sysc_addr;
 };
 
 /* Provide a method for preventing idling some ARM IDLECT clocks */
 struct arm_idlect1_clk {
-	struct clk	clk;
-	unsigned long	no_idle_count;
-	__u8		idlect_shift;
+	struct omap1_clk	clk;
+	unsigned long		no_idle_count;
+	__u8			idlect_shift;
 };
 
 /* ARM_CKCTL bit shifts */
@@ -275,14 +178,18 @@ struct arm_idlect1_clk {
 #define SOFT_REQ_REG2		0xfffe0880
 
 extern __u32 arm_idlect1_mask;
-extern struct clk *api_ck_p, *ck_dpll1_p, *ck_ref_p;
+extern struct omap1_clk *api_ck_p, *ck_dpll1_p, *ck_ref_p;
 
 extern const struct clkops clkops_dspck;
-extern const struct clkops clkops_dummy;
 extern const struct clkops clkops_uart_16xx;
 extern const struct clkops clkops_generic;
 
 /* used for passing SoC type to omap1_{select,round_to}_table_rate() */
 extern u32 cpu_mask;
 
+extern const struct clk_ops omap1_clk_null_ops;
+extern const struct clk_ops omap1_clk_gate_ops;
+extern const struct clk_ops omap1_clk_rate_ops;
+extern const struct clk_ops omap1_clk_full_ops;
+
 #endif
diff --git a/arch/arm/mach-omap1/clock_data.c b/arch/arm/mach-omap1/clock_data.c
index 3ebcd96efbff..96d846c37c43 100644
--- a/arch/arm/mach-omap1/clock_data.c
+++ b/arch/arm/mach-omap1/clock_data.c
@@ -14,16 +14,17 @@
 #include <linux/kernel.h>
 #include <linux/io.h>
 #include <linux/clk.h>
+#include <linux/clkdev.h>
+#include <linux/clk-provider.h>
 #include <linux/cpufreq.h>
 #include <linux/delay.h>
+#include <linux/soc/ti/omap1-io.h>
 
 #include <asm/mach-types.h>  /* for machine_is_* */
 
 #include "soc.h"
-
-#include <mach/hardware.h>
-#include <mach/usb.h>   /* for OTG_BASE */
-
+#include "hardware.h"
+#include "usb.h"   /* for OTG_BASE */
 #include "iomap.h"
 #include "clock.h"
 #include "sram.h"
@@ -72,16 +73,18 @@
  * Omap1 clocks
  */
 
-static struct clk ck_ref = {
-	.name		= "ck_ref",
-	.ops		= &clkops_null,
+static struct omap1_clk ck_ref = {
+	.hw.init	= CLK_HW_INIT_NO_PARENT("ck_ref", &omap1_clk_rate_ops, 0),
 	.rate		= 12000000,
 };
 
-static struct clk ck_dpll1 = {
-	.name		= "ck_dpll1",
-	.ops		= &clkops_null,
-	.parent		= &ck_ref,
+static struct omap1_clk ck_dpll1 = {
+	.hw.init	= CLK_HW_INIT("ck_dpll1", "ck_ref", &omap1_clk_rate_ops,
+				      /*
+				       * force recursive refresh of rates of the clock
+				       * and its children when clk_get_rate() is called
+				       */
+				      CLK_GET_RATE_NOCACHE),
 };
 
 /*
@@ -90,33 +93,28 @@ static struct clk ck_dpll1 = {
  */
 static struct arm_idlect1_clk ck_dpll1out = {
 	.clk = {
-		.name		= "ck_dpll1out",
+		.hw.init	= CLK_HW_INIT("ck_dpll1out", "ck_dpll1", &omap1_clk_gate_ops, 0),
 		.ops		= &clkops_generic,
-		.parent		= &ck_dpll1,
-		.flags		= CLOCK_IDLE_CONTROL | ENABLE_REG_32BIT |
-				  ENABLE_ON_INIT,
+		.flags		= CLOCK_IDLE_CONTROL | ENABLE_REG_32BIT,
 		.enable_reg	= OMAP1_IO_ADDRESS(ARM_IDLECT2),
 		.enable_bit	= EN_CKOUT_ARM,
-		.recalc		= &followparent_recalc,
 	},
 	.idlect_shift	= IDL_CLKOUT_ARM_SHIFT,
 };
 
-static struct clk sossi_ck = {
-	.name		= "ck_sossi",
+static struct omap1_clk sossi_ck = {
+	.hw.init	= CLK_HW_INIT("ck_sossi", "ck_dpll1out", &omap1_clk_full_ops, 0),
 	.ops		= &clkops_generic,
-	.parent		= &ck_dpll1out.clk,
 	.flags		= CLOCK_NO_IDLE_PARENT | ENABLE_REG_32BIT,
 	.enable_reg	= OMAP1_IO_ADDRESS(MOD_CONF_CTRL_1),
 	.enable_bit	= CONF_MOD_SOSSI_CLK_EN_R,
 	.recalc		= &omap1_sossi_recalc,
+	.round_rate	= &omap1_round_sossi_rate,
 	.set_rate	= &omap1_set_sossi_rate,
 };
 
-static struct clk arm_ck = {
-	.name		= "arm_ck",
-	.ops		= &clkops_null,
-	.parent		= &ck_dpll1,
+static struct omap1_clk arm_ck = {
+	.hw.init	= CLK_HW_INIT("arm_ck", "ck_dpll1", &omap1_clk_rate_ops, 0),
 	.rate_offset	= CKCTL_ARMDIV_OFFSET,
 	.recalc		= &omap1_ckctl_recalc,
 	.round_rate	= omap1_clk_round_rate_ckctl_arm,
@@ -125,9 +123,9 @@ static struct clk arm_ck = {
 
 static struct arm_idlect1_clk armper_ck = {
 	.clk = {
-		.name		= "armper_ck",
+		.hw.init	= CLK_HW_INIT("armper_ck", "ck_dpll1", &omap1_clk_full_ops,
+					      CLK_IS_CRITICAL),
 		.ops		= &clkops_generic,
-		.parent		= &ck_dpll1,
 		.flags		= CLOCK_IDLE_CONTROL,
 		.enable_reg	= OMAP1_IO_ADDRESS(ARM_IDLECT2),
 		.enable_bit	= EN_PERCK,
@@ -143,47 +141,41 @@ static struct arm_idlect1_clk armper_ck = {
  * FIXME: This clock seems to be necessary but no-one has asked for its
  * activation.  [ GPIO code for 1510 ]
  */
-static struct clk arm_gpio_ck = {
-	.name		= "ick",
+static struct omap1_clk arm_gpio_ck = {
+	.hw.init	= CLK_HW_INIT("ick", "ck_dpll1", &omap1_clk_gate_ops, CLK_IS_CRITICAL),
 	.ops		= &clkops_generic,
-	.parent		= &ck_dpll1,
-	.flags		= ENABLE_ON_INIT,
 	.enable_reg	= OMAP1_IO_ADDRESS(ARM_IDLECT2),
 	.enable_bit	= EN_GPIOCK,
-	.recalc		= &followparent_recalc,
 };
 
 static struct arm_idlect1_clk armxor_ck = {
 	.clk = {
-		.name		= "armxor_ck",
+		.hw.init	= CLK_HW_INIT("armxor_ck", "ck_ref", &omap1_clk_gate_ops,
+					      CLK_IS_CRITICAL),
 		.ops		= &clkops_generic,
-		.parent		= &ck_ref,
 		.flags		= CLOCK_IDLE_CONTROL,
 		.enable_reg	= OMAP1_IO_ADDRESS(ARM_IDLECT2),
 		.enable_bit	= EN_XORPCK,
-		.recalc		= &followparent_recalc,
 	},
 	.idlect_shift	= IDLXORP_ARM_SHIFT,
 };
 
 static struct arm_idlect1_clk armtim_ck = {
 	.clk = {
-		.name		= "armtim_ck",
+		.hw.init	= CLK_HW_INIT("armtim_ck", "ck_ref", &omap1_clk_gate_ops,
+					      CLK_IS_CRITICAL),
 		.ops		= &clkops_generic,
-		.parent		= &ck_ref,
 		.flags		= CLOCK_IDLE_CONTROL,
 		.enable_reg	= OMAP1_IO_ADDRESS(ARM_IDLECT2),
 		.enable_bit	= EN_TIMCK,
-		.recalc		= &followparent_recalc,
 	},
 	.idlect_shift	= IDLTIM_ARM_SHIFT,
 };
 
 static struct arm_idlect1_clk armwdt_ck = {
 	.clk = {
-		.name		= "armwdt_ck",
+		.hw.init	= CLK_HW_INIT("armwdt_ck", "ck_ref", &omap1_clk_full_ops, 0),
 		.ops		= &clkops_generic,
-		.parent		= &ck_ref,
 		.flags		= CLOCK_IDLE_CONTROL,
 		.enable_reg	= OMAP1_IO_ADDRESS(ARM_IDLECT2),
 		.enable_bit	= EN_WDTCK,
@@ -193,11 +185,8 @@ static struct arm_idlect1_clk armwdt_ck = {
 	.idlect_shift	= IDLWDT_ARM_SHIFT,
 };
 
-static struct clk arminth_ck16xx = {
-	.name		= "arminth_ck",
-	.ops		= &clkops_null,
-	.parent		= &arm_ck,
-	.recalc		= &followparent_recalc,
+static struct omap1_clk arminth_ck16xx = {
+	.hw.init	= CLK_HW_INIT("arminth_ck", "arm_ck", &omap1_clk_null_ops, 0),
 	/* Note: On 16xx the frequency can be divided by 2 by programming
 	 * ARM_CKCTL:ARM_INTHCK_SEL(14) to 1
 	 *
@@ -205,10 +194,9 @@ static struct clk arminth_ck16xx = {
 	 */
 };
 
-static struct clk dsp_ck = {
-	.name		= "dsp_ck",
+static struct omap1_clk dsp_ck = {
+	.hw.init	= CLK_HW_INIT("dsp_ck", "ck_dpll1", &omap1_clk_full_ops, 0),
 	.ops		= &clkops_generic,
-	.parent		= &ck_dpll1,
 	.enable_reg	= OMAP1_IO_ADDRESS(ARM_CKCTL),
 	.enable_bit	= EN_DSPCK,
 	.rate_offset	= CKCTL_DSPDIV_OFFSET,
@@ -217,20 +205,17 @@ static struct clk dsp_ck = {
 	.set_rate	= omap1_clk_set_rate_ckctl_arm,
 };
 
-static struct clk dspmmu_ck = {
-	.name		= "dspmmu_ck",
-	.ops		= &clkops_null,
-	.parent		= &ck_dpll1,
+static struct omap1_clk dspmmu_ck = {
+	.hw.init	= CLK_HW_INIT("dspmmu_ck", "ck_dpll1", &omap1_clk_rate_ops, 0),
 	.rate_offset	= CKCTL_DSPMMUDIV_OFFSET,
 	.recalc		= &omap1_ckctl_recalc,
 	.round_rate	= omap1_clk_round_rate_ckctl_arm,
 	.set_rate	= omap1_clk_set_rate_ckctl_arm,
 };
 
-static struct clk dspper_ck = {
-	.name		= "dspper_ck",
+static struct omap1_clk dspper_ck = {
+	.hw.init	= CLK_HW_INIT("dspper_ck", "ck_dpll1", &omap1_clk_full_ops, 0),
 	.ops		= &clkops_dspck,
-	.parent		= &ck_dpll1,
 	.enable_reg	= DSP_IDLECT2,
 	.enable_bit	= EN_PERCK,
 	.rate_offset	= CKCTL_PERDIV_OFFSET,
@@ -239,29 +224,23 @@ static struct clk dspper_ck = {
 	.set_rate	= &omap1_clk_set_rate_dsp_domain,
 };
 
-static struct clk dspxor_ck = {
-	.name		= "dspxor_ck",
+static struct omap1_clk dspxor_ck = {
+	.hw.init	= CLK_HW_INIT("dspxor_ck", "ck_ref", &omap1_clk_gate_ops, 0),
 	.ops		= &clkops_dspck,
-	.parent		= &ck_ref,
 	.enable_reg	= DSP_IDLECT2,
 	.enable_bit	= EN_XORPCK,
-	.recalc		= &followparent_recalc,
 };
 
-static struct clk dsptim_ck = {
-	.name		= "dsptim_ck",
+static struct omap1_clk dsptim_ck = {
+	.hw.init	= CLK_HW_INIT("dsptim_ck", "ck_ref", &omap1_clk_gate_ops, 0),
 	.ops		= &clkops_dspck,
-	.parent		= &ck_ref,
 	.enable_reg	= DSP_IDLECT2,
 	.enable_bit	= EN_DSPTIMCK,
-	.recalc		= &followparent_recalc,
 };
 
 static struct arm_idlect1_clk tc_ck = {
 	.clk = {
-		.name		= "tc_ck",
-		.ops		= &clkops_null,
-		.parent		= &ck_dpll1,
+		.hw.init	= CLK_HW_INIT("tc_ck", "ck_dpll1", &omap1_clk_rate_ops, 0),
 		.flags		= CLOCK_IDLE_CONTROL,
 		.rate_offset	= CKCTL_TCDIV_OFFSET,
 		.recalc		= &omap1_ckctl_recalc,
@@ -271,117 +250,88 @@ static struct arm_idlect1_clk tc_ck = {
 	.idlect_shift	= IDLIF_ARM_SHIFT,
 };
 
-static struct clk arminth_ck1510 = {
-	.name		= "arminth_ck",
-	.ops		= &clkops_null,
-	.parent		= &tc_ck.clk,
-	.recalc		= &followparent_recalc,
+static struct omap1_clk arminth_ck1510 = {
+	.hw.init	= CLK_HW_INIT("arminth_ck", "tc_ck", &omap1_clk_null_ops, 0),
 	/* Note: On 1510 the frequency follows TC_CK
 	 *
 	 * 16xx version is in MPU clocks.
 	 */
 };
 
-static struct clk tipb_ck = {
+static struct omap1_clk tipb_ck = {
 	/* No-idle controlled by "tc_ck" */
-	.name		= "tipb_ck",
-	.ops		= &clkops_null,
-	.parent		= &tc_ck.clk,
-	.recalc		= &followparent_recalc,
+	.hw.init	= CLK_HW_INIT("tipb_ck", "tc_ck", &omap1_clk_null_ops, 0),
 };
 
-static struct clk l3_ocpi_ck = {
+static struct omap1_clk l3_ocpi_ck = {
 	/* No-idle controlled by "tc_ck" */
-	.name		= "l3_ocpi_ck",
+	.hw.init	= CLK_HW_INIT("l3_ocpi_ck", "tc_ck", &omap1_clk_gate_ops, 0),
 	.ops		= &clkops_generic,
-	.parent		= &tc_ck.clk,
 	.enable_reg	= OMAP1_IO_ADDRESS(ARM_IDLECT3),
 	.enable_bit	= EN_OCPI_CK,
-	.recalc		= &followparent_recalc,
 };
 
-static struct clk tc1_ck = {
-	.name		= "tc1_ck",
+static struct omap1_clk tc1_ck = {
+	.hw.init	= CLK_HW_INIT("tc1_ck", "tc_ck", &omap1_clk_gate_ops, 0),
 	.ops		= &clkops_generic,
-	.parent		= &tc_ck.clk,
 	.enable_reg	= OMAP1_IO_ADDRESS(ARM_IDLECT3),
 	.enable_bit	= EN_TC1_CK,
-	.recalc		= &followparent_recalc,
 };
 
 /*
  * FIXME: This clock seems to be necessary but no-one has asked for its
  * activation.  [ pm.c (SRAM), CCP, Camera ]
  */
-static struct clk tc2_ck = {
-	.name		= "tc2_ck",
+
+static struct omap1_clk tc2_ck = {
+	.hw.init	= CLK_HW_INIT("tc2_ck", "tc_ck", &omap1_clk_gate_ops, CLK_IS_CRITICAL),
 	.ops		= &clkops_generic,
-	.parent		= &tc_ck.clk,
-	.flags		= ENABLE_ON_INIT,
 	.enable_reg	= OMAP1_IO_ADDRESS(ARM_IDLECT3),
 	.enable_bit	= EN_TC2_CK,
-	.recalc		= &followparent_recalc,
 };
 
-static struct clk dma_ck = {
+static struct omap1_clk dma_ck = {
 	/* No-idle controlled by "tc_ck" */
-	.name		= "dma_ck",
-	.ops		= &clkops_null,
-	.parent		= &tc_ck.clk,
-	.recalc		= &followparent_recalc,
+	.hw.init	= CLK_HW_INIT("dma_ck", "tc_ck", &omap1_clk_null_ops, 0),
 };
 
-static struct clk dma_lcdfree_ck = {
-	.name		= "dma_lcdfree_ck",
-	.ops		= &clkops_null,
-	.parent		= &tc_ck.clk,
-	.recalc		= &followparent_recalc,
+static struct omap1_clk dma_lcdfree_ck = {
+	.hw.init	= CLK_HW_INIT("dma_lcdfree_ck", "tc_ck", &omap1_clk_null_ops, 0),
 };
 
 static struct arm_idlect1_clk api_ck = {
 	.clk = {
-		.name		= "api_ck",
+		.hw.init	= CLK_HW_INIT("api_ck", "tc_ck", &omap1_clk_gate_ops, 0),
 		.ops		= &clkops_generic,
-		.parent		= &tc_ck.clk,
 		.flags		= CLOCK_IDLE_CONTROL,
 		.enable_reg	= OMAP1_IO_ADDRESS(ARM_IDLECT2),
 		.enable_bit	= EN_APICK,
-		.recalc		= &followparent_recalc,
 	},
 	.idlect_shift	= IDLAPI_ARM_SHIFT,
 };
 
 static struct arm_idlect1_clk lb_ck = {
 	.clk = {
-		.name		= "lb_ck",
+		.hw.init	= CLK_HW_INIT("lb_ck", "tc_ck", &omap1_clk_gate_ops, 0),
 		.ops		= &clkops_generic,
-		.parent		= &tc_ck.clk,
 		.flags		= CLOCK_IDLE_CONTROL,
 		.enable_reg	= OMAP1_IO_ADDRESS(ARM_IDLECT2),
 		.enable_bit	= EN_LBCK,
-		.recalc		= &followparent_recalc,
 	},
 	.idlect_shift	= IDLLB_ARM_SHIFT,
 };
 
-static struct clk rhea1_ck = {
-	.name		= "rhea1_ck",
-	.ops		= &clkops_null,
-	.parent		= &tc_ck.clk,
-	.recalc		= &followparent_recalc,
+static struct omap1_clk rhea1_ck = {
+	.hw.init	= CLK_HW_INIT("rhea1_ck", "tc_ck", &omap1_clk_null_ops, 0),
 };
 
-static struct clk rhea2_ck = {
-	.name		= "rhea2_ck",
-	.ops		= &clkops_null,
-	.parent		= &tc_ck.clk,
-	.recalc		= &followparent_recalc,
+static struct omap1_clk rhea2_ck = {
+	.hw.init	= CLK_HW_INIT("rhea2_ck", "tc_ck", &omap1_clk_null_ops, 0),
 };
 
-static struct clk lcd_ck_16xx = {
-	.name		= "lcd_ck",
+static struct omap1_clk lcd_ck_16xx = {
+	.hw.init	= CLK_HW_INIT("lcd_ck", "ck_dpll1", &omap1_clk_full_ops, 0),
 	.ops		= &clkops_generic,
-	.parent		= &ck_dpll1,
 	.enable_reg	= OMAP1_IO_ADDRESS(ARM_IDLECT2),
 	.enable_bit	= EN_LCDCK,
 	.rate_offset	= CKCTL_LCDDIV_OFFSET,
@@ -392,9 +342,8 @@ static struct clk lcd_ck_16xx = {
 
 static struct arm_idlect1_clk lcd_ck_1510 = {
 	.clk = {
-		.name		= "lcd_ck",
+		.hw.init	= CLK_HW_INIT("lcd_ck", "ck_dpll1", &omap1_clk_full_ops, 0),
 		.ops		= &clkops_generic,
-		.parent		= &ck_dpll1,
 		.flags		= CLOCK_IDLE_CONTROL,
 		.enable_reg	= OMAP1_IO_ADDRESS(ARM_IDLECT2),
 		.enable_bit	= EN_LCDCK,
@@ -406,37 +355,35 @@ static struct arm_idlect1_clk lcd_ck_1510 = {
 	.idlect_shift	= OMAP1510_IDLLCD_ARM_SHIFT,
 };
 
+
 /*
  * XXX The enable_bit here is misused - it simply switches between 12MHz
- * and 48MHz.  Reimplement with clksel.
+ * and 48MHz.  Reimplement with clk_mux.
  *
  * XXX does this need SYSC register handling?
  */
-static struct clk uart1_1510 = {
-	.name		= "uart1_ck",
-	.ops		= &clkops_null,
+static struct omap1_clk uart1_1510 = {
 	/* Direct from ULPD, no real parent */
-	.parent		= &armper_ck.clk,
-	.rate		= 12000000,
+	.hw.init	= CLK_HW_INIT("uart1_ck", "armper_ck", &omap1_clk_full_ops, 0),
 	.flags		= ENABLE_REG_32BIT | CLOCK_NO_IDLE_PARENT,
 	.enable_reg	= OMAP1_IO_ADDRESS(MOD_CONF_CTRL_0),
 	.enable_bit	= CONF_MOD_UART1_CLK_MODE_R,
+	.round_rate	= &omap1_round_uart_rate,
 	.set_rate	= &omap1_set_uart_rate,
 	.recalc		= &omap1_uart_recalc,
 };
 
 /*
  * XXX The enable_bit here is misused - it simply switches between 12MHz
- * and 48MHz.  Reimplement with clksel.
+ * and 48MHz.  Reimplement with clk_mux.
  *
  * XXX SYSC register handling does not belong in the clock framework
  */
 static struct uart_clk uart1_16xx = {
 	.clk	= {
-		.name		= "uart1_ck",
 		.ops		= &clkops_uart_16xx,
 		/* Direct from ULPD, no real parent */
-		.parent		= &armper_ck.clk,
+		.hw.init	= CLK_HW_INIT("uart1_ck", "armper_ck", &omap1_clk_full_ops, 0),
 		.rate		= 48000000,
 		.flags		= ENABLE_REG_32BIT | CLOCK_NO_IDLE_PARENT,
 		.enable_reg	= OMAP1_IO_ADDRESS(MOD_CONF_CTRL_0),
@@ -447,54 +394,49 @@ static struct uart_clk uart1_16xx = {
 
 /*
  * XXX The enable_bit here is misused - it simply switches between 12MHz
- * and 48MHz.  Reimplement with clksel.
+ * and 48MHz.  Reimplement with clk_mux.
  *
  * XXX does this need SYSC register handling?
  */
-static struct clk uart2_ck = {
-	.name		= "uart2_ck",
-	.ops		= &clkops_null,
+static struct omap1_clk uart2_ck = {
 	/* Direct from ULPD, no real parent */
-	.parent		= &armper_ck.clk,
-	.rate		= 12000000,
+	.hw.init	= CLK_HW_INIT("uart2_ck", "armper_ck", &omap1_clk_full_ops, 0),
 	.flags		= ENABLE_REG_32BIT | CLOCK_NO_IDLE_PARENT,
 	.enable_reg	= OMAP1_IO_ADDRESS(MOD_CONF_CTRL_0),
 	.enable_bit	= CONF_MOD_UART2_CLK_MODE_R,
+	.round_rate	= &omap1_round_uart_rate,
 	.set_rate	= &omap1_set_uart_rate,
 	.recalc		= &omap1_uart_recalc,
 };
 
 /*
  * XXX The enable_bit here is misused - it simply switches between 12MHz
- * and 48MHz.  Reimplement with clksel.
+ * and 48MHz.  Reimplement with clk_mux.
  *
  * XXX does this need SYSC register handling?
  */
-static struct clk uart3_1510 = {
-	.name		= "uart3_ck",
-	.ops		= &clkops_null,
+static struct omap1_clk uart3_1510 = {
 	/* Direct from ULPD, no real parent */
-	.parent		= &armper_ck.clk,
-	.rate		= 12000000,
+	.hw.init	= CLK_HW_INIT("uart3_ck", "armper_ck", &omap1_clk_full_ops, 0),
 	.flags		= ENABLE_REG_32BIT | CLOCK_NO_IDLE_PARENT,
 	.enable_reg	= OMAP1_IO_ADDRESS(MOD_CONF_CTRL_0),
 	.enable_bit	= CONF_MOD_UART3_CLK_MODE_R,
+	.round_rate	= &omap1_round_uart_rate,
 	.set_rate	= &omap1_set_uart_rate,
 	.recalc		= &omap1_uart_recalc,
 };
 
 /*
  * XXX The enable_bit here is misused - it simply switches between 12MHz
- * and 48MHz.  Reimplement with clksel.
+ * and 48MHz.  Reimplement with clk_mux.
  *
  * XXX SYSC register handling does not belong in the clock framework
  */
 static struct uart_clk uart3_16xx = {
 	.clk	= {
-		.name		= "uart3_ck",
 		.ops		= &clkops_uart_16xx,
 		/* Direct from ULPD, no real parent */
-		.parent		= &armper_ck.clk,
+		.hw.init	= CLK_HW_INIT("uart3_ck", "armper_ck", &omap1_clk_full_ops, 0),
 		.rate		= 48000000,
 		.flags		= ENABLE_REG_32BIT | CLOCK_NO_IDLE_PARENT,
 		.enable_reg	= OMAP1_IO_ADDRESS(MOD_CONF_CTRL_0),
@@ -503,30 +445,30 @@ static struct uart_clk uart3_16xx = {
 	.sysc_addr	= 0xfffb9854,
 };
 
-static struct clk usb_clko = {	/* 6 MHz output on W4_USB_CLKO */
-	.name		= "usb_clko",
+static struct omap1_clk usb_clko = {	/* 6 MHz output on W4_USB_CLKO */
 	.ops		= &clkops_generic,
 	/* Direct from ULPD, no parent */
+	.hw.init	= CLK_HW_INIT_NO_PARENT("usb_clko", &omap1_clk_full_ops, 0),
 	.rate		= 6000000,
 	.flags		= ENABLE_REG_32BIT,
 	.enable_reg	= OMAP1_IO_ADDRESS(ULPD_CLOCK_CTRL),
 	.enable_bit	= USB_MCLK_EN_BIT,
 };
 
-static struct clk usb_hhc_ck1510 = {
-	.name		= "usb_hhc_ck",
+static struct omap1_clk usb_hhc_ck1510 = {
 	.ops		= &clkops_generic,
 	/* Direct from ULPD, no parent */
+	.hw.init	= CLK_HW_INIT_NO_PARENT("usb_hhc_ck", &omap1_clk_full_ops, 0),
 	.rate		= 48000000, /* Actually 2 clocks, 12MHz and 48MHz */
 	.flags		= ENABLE_REG_32BIT,
 	.enable_reg	= OMAP1_IO_ADDRESS(MOD_CONF_CTRL_0),
 	.enable_bit	= USB_HOST_HHC_UHOST_EN,
 };
 
-static struct clk usb_hhc_ck16xx = {
-	.name		= "usb_hhc_ck",
+static struct omap1_clk usb_hhc_ck16xx = {
 	.ops		= &clkops_generic,
 	/* Direct from ULPD, no parent */
+	.hw.init	= CLK_HW_INIT_NO_PARENT("usb_hhc_ck", &omap1_clk_full_ops, 0),
 	.rate		= 48000000,
 	/* OTG_SYSCON_2.OTG_PADEN == 0 (not 1510-compatible) */
 	.flags		= ENABLE_REG_32BIT,
@@ -534,46 +476,46 @@ static struct clk usb_hhc_ck16xx = {
 	.enable_bit	= OTG_SYSCON_2_UHOST_EN_SHIFT
 };
 
-static struct clk usb_dc_ck = {
-	.name		= "usb_dc_ck",
+static struct omap1_clk usb_dc_ck = {
 	.ops		= &clkops_generic,
 	/* Direct from ULPD, no parent */
+	.hw.init	= CLK_HW_INIT_NO_PARENT("usb_dc_ck", &omap1_clk_full_ops, 0),
 	.rate		= 48000000,
 	.enable_reg	= OMAP1_IO_ADDRESS(SOFT_REQ_REG),
 	.enable_bit	= SOFT_USB_OTG_DPLL_REQ_SHIFT,
 };
 
-static struct clk uart1_7xx = {
-	.name		= "uart1_ck",
+static struct omap1_clk uart1_7xx = {
 	.ops		= &clkops_generic,
 	/* Direct from ULPD, no parent */
+	.hw.init	= CLK_HW_INIT_NO_PARENT("uart1_ck", &omap1_clk_full_ops, 0),
 	.rate		= 12000000,
 	.enable_reg	= OMAP1_IO_ADDRESS(SOFT_REQ_REG),
 	.enable_bit	= 9,
 };
 
-static struct clk uart2_7xx = {
-	.name		= "uart2_ck",
+static struct omap1_clk uart2_7xx = {
 	.ops		= &clkops_generic,
 	/* Direct from ULPD, no parent */
+	.hw.init	= CLK_HW_INIT_NO_PARENT("uart2_ck", &omap1_clk_full_ops, 0),
 	.rate		= 12000000,
 	.enable_reg	= OMAP1_IO_ADDRESS(SOFT_REQ_REG),
 	.enable_bit	= 11,
 };
 
-static struct clk mclk_1510 = {
-	.name		= "mclk",
+static struct omap1_clk mclk_1510 = {
 	.ops		= &clkops_generic,
 	/* Direct from ULPD, no parent. May be enabled by ext hardware. */
+	.hw.init	= CLK_HW_INIT_NO_PARENT("mclk", &omap1_clk_full_ops, 0),
 	.rate		= 12000000,
 	.enable_reg	= OMAP1_IO_ADDRESS(SOFT_REQ_REG),
 	.enable_bit	= SOFT_COM_MCKO_REQ_SHIFT,
 };
 
-static struct clk mclk_16xx = {
-	.name		= "mclk",
+static struct omap1_clk mclk_16xx = {
 	.ops		= &clkops_generic,
 	/* Direct from ULPD, no parent. May be enabled by ext hardware. */
+	.hw.init	= CLK_HW_INIT_NO_PARENT("mclk", &omap1_clk_full_ops, 0),
 	.enable_reg	= OMAP1_IO_ADDRESS(COM_CLK_DIV_CTRL_SEL),
 	.enable_bit	= COM_ULPD_PLL_CLK_REQ,
 	.set_rate	= &omap1_set_ext_clk_rate,
@@ -581,17 +523,16 @@ static struct clk mclk_16xx = {
 	.init		= &omap1_init_ext_clk,
 };
 
-static struct clk bclk_1510 = {
-	.name		= "bclk",
-	.ops		= &clkops_generic,
+static struct omap1_clk bclk_1510 = {
 	/* Direct from ULPD, no parent. May be enabled by ext hardware. */
+	.hw.init	= CLK_HW_INIT_NO_PARENT("bclk", &omap1_clk_rate_ops, 0),
 	.rate		= 12000000,
 };
 
-static struct clk bclk_16xx = {
-	.name		= "bclk",
+static struct omap1_clk bclk_16xx = {
 	.ops		= &clkops_generic,
 	/* Direct from ULPD, no parent. May be enabled by ext hardware. */
+	.hw.init	= CLK_HW_INIT_NO_PARENT("bclk", &omap1_clk_full_ops, 0),
 	.enable_reg	= OMAP1_IO_ADDRESS(SWD_CLK_DIV_CTRL_SEL),
 	.enable_bit	= SWD_ULPD_PLL_CLK_REQ,
 	.set_rate	= &omap1_set_ext_clk_rate,
@@ -599,11 +540,10 @@ static struct clk bclk_16xx = {
 	.init		= &omap1_init_ext_clk,
 };
 
-static struct clk mmc1_ck = {
-	.name		= "mmc1_ck",
+static struct omap1_clk mmc1_ck = {
 	.ops		= &clkops_generic,
 	/* Functional clock is direct from ULPD, interface clock is ARMPER */
-	.parent		= &armper_ck.clk,
+	.hw.init	= CLK_HW_INIT("mmc1_ck", "armper_ck", &omap1_clk_full_ops, 0),
 	.rate		= 48000000,
 	.flags		= ENABLE_REG_32BIT | CLOCK_NO_IDLE_PARENT,
 	.enable_reg	= OMAP1_IO_ADDRESS(MOD_CONF_CTRL_0),
@@ -614,32 +554,29 @@ static struct clk mmc1_ck = {
  * XXX MOD_CONF_CTRL_0 bit 20 is defined in the 1510 TRM as
  * CONF_MOD_MCBSP3_AUXON ??
  */
-static struct clk mmc2_ck = {
-	.name		= "mmc2_ck",
+static struct omap1_clk mmc2_ck = {
 	.ops		= &clkops_generic,
 	/* Functional clock is direct from ULPD, interface clock is ARMPER */
-	.parent		= &armper_ck.clk,
+	.hw.init	= CLK_HW_INIT("mmc2_ck", "armper_ck", &omap1_clk_full_ops, 0),
 	.rate		= 48000000,
 	.flags		= ENABLE_REG_32BIT | CLOCK_NO_IDLE_PARENT,
 	.enable_reg	= OMAP1_IO_ADDRESS(MOD_CONF_CTRL_0),
 	.enable_bit	= 20,
 };
 
-static struct clk mmc3_ck = {
-	.name		= "mmc3_ck",
+static struct omap1_clk mmc3_ck = {
 	.ops		= &clkops_generic,
 	/* Functional clock is direct from ULPD, interface clock is ARMPER */
-	.parent		= &armper_ck.clk,
+	.hw.init	= CLK_HW_INIT("mmc3_ck", "armper_ck", &omap1_clk_full_ops, 0),
 	.rate		= 48000000,
 	.flags		= ENABLE_REG_32BIT | CLOCK_NO_IDLE_PARENT,
 	.enable_reg	= OMAP1_IO_ADDRESS(SOFT_REQ_REG),
 	.enable_bit	= SOFT_MMC_DPLL_REQ_SHIFT,
 };
 
-static struct clk virtual_ck_mpu = {
-	.name		= "mpu",
-	.ops		= &clkops_null,
-	.parent		= &arm_ck, /* Is smarter alias for */
+static struct omap1_clk virtual_ck_mpu = {
+	/* Is smarter alias for arm_ck */
+	.hw.init	= CLK_HW_INIT("mpu", "arm_ck", &omap1_clk_rate_ops, 0),
 	.recalc		= &followparent_recalc,
 	.set_rate	= &omap1_select_table_rate,
 	.round_rate	= &omap1_round_to_table_rate,
@@ -647,20 +584,14 @@ static struct clk virtual_ck_mpu = {
 
 /* virtual functional clock domain for I2C. Just for making sure that ARMXOR_CK
 remains active during MPU idle whenever this is enabled */
-static struct clk i2c_fck = {
-	.name		= "i2c_fck",
-	.ops		= &clkops_null,
+static struct omap1_clk i2c_fck = {
+	.hw.init	= CLK_HW_INIT("i2c_fck", "armxor_ck", &omap1_clk_gate_ops, 0),
 	.flags		= CLOCK_NO_IDLE_PARENT,
-	.parent		= &armxor_ck.clk,
-	.recalc		= &followparent_recalc,
 };
 
-static struct clk i2c_ick = {
-	.name		= "i2c_ick",
-	.ops		= &clkops_null,
+static struct omap1_clk i2c_ick = {
+	.hw.init	= CLK_HW_INIT("i2c_ick", "armper_ck", &omap1_clk_gate_ops, 0),
 	.flags		= CLOCK_NO_IDLE_PARENT,
-	.parent		= &armper_ck.clk,
-	.recalc		= &followparent_recalc,
 };
 
 /*
@@ -669,81 +600,81 @@ static struct clk i2c_ick = {
 
 static struct omap_clk omap_clks[] = {
 	/* non-ULPD clocks */
-	CLK(NULL,	"ck_ref",	&ck_ref,	CK_16XX | CK_1510 | CK_310 | CK_7XX),
-	CLK(NULL,	"ck_dpll1",	&ck_dpll1,	CK_16XX | CK_1510 | CK_310 | CK_7XX),
+	CLK(NULL,	"ck_ref",	&ck_ref.hw,	CK_16XX | CK_1510 | CK_310 | CK_7XX),
+	CLK(NULL,	"ck_dpll1",	&ck_dpll1.hw,	CK_16XX | CK_1510 | CK_310 | CK_7XX),
 	/* CK_GEN1 clocks */
-	CLK(NULL,	"ck_dpll1out",	&ck_dpll1out.clk, CK_16XX),
-	CLK(NULL,	"ck_sossi",	&sossi_ck,	CK_16XX),
-	CLK(NULL,	"arm_ck",	&arm_ck,	CK_16XX | CK_1510 | CK_310),
-	CLK(NULL,	"armper_ck",	&armper_ck.clk,	CK_16XX | CK_1510 | CK_310),
-	CLK("omap_gpio.0", "ick",	&arm_gpio_ck,	CK_1510 | CK_310),
-	CLK(NULL,	"armxor_ck",	&armxor_ck.clk,	CK_16XX | CK_1510 | CK_310 | CK_7XX),
-	CLK(NULL,	"armtim_ck",	&armtim_ck.clk,	CK_16XX | CK_1510 | CK_310),
-	CLK("omap_wdt",	"fck",		&armwdt_ck.clk,	CK_16XX | CK_1510 | CK_310),
-	CLK("omap_wdt",	"ick",		&armper_ck.clk,	CK_16XX),
-	CLK("omap_wdt", "ick",		&dummy_ck,	CK_1510 | CK_310),
-	CLK(NULL,	"arminth_ck",	&arminth_ck1510, CK_1510 | CK_310),
-	CLK(NULL,	"arminth_ck",	&arminth_ck16xx, CK_16XX),
+	CLK(NULL,	"ck_dpll1out",	&ck_dpll1out.clk.hw, CK_16XX),
+	CLK(NULL,	"ck_sossi",	&sossi_ck.hw,	CK_16XX),
+	CLK(NULL,	"arm_ck",	&arm_ck.hw,	CK_16XX | CK_1510 | CK_310),
+	CLK(NULL,	"armper_ck",	&armper_ck.clk.hw, CK_16XX | CK_1510 | CK_310),
+	CLK("omap_gpio.0", "ick",	&arm_gpio_ck.hw, CK_1510 | CK_310),
+	CLK(NULL,	"armxor_ck",	&armxor_ck.clk.hw, CK_16XX | CK_1510 | CK_310 | CK_7XX),
+	CLK(NULL,	"armtim_ck",	&armtim_ck.clk.hw, CK_16XX | CK_1510 | CK_310),
+	CLK("omap_wdt",	"fck",		&armwdt_ck.clk.hw, CK_16XX | CK_1510 | CK_310),
+	CLK("omap_wdt",	"ick",		&armper_ck.clk.hw, CK_16XX),
+	CLK("omap_wdt", "ick",		&dummy_ck.hw,	CK_1510 | CK_310),
+	CLK(NULL,	"arminth_ck",	&arminth_ck1510.hw, CK_1510 | CK_310),
+	CLK(NULL,	"arminth_ck",	&arminth_ck16xx.hw, CK_16XX),
 	/* CK_GEN2 clocks */
-	CLK(NULL,	"dsp_ck",	&dsp_ck,	CK_16XX | CK_1510 | CK_310),
-	CLK(NULL,	"dspmmu_ck",	&dspmmu_ck,	CK_16XX | CK_1510 | CK_310),
-	CLK(NULL,	"dspper_ck",	&dspper_ck,	CK_16XX | CK_1510 | CK_310),
-	CLK(NULL,	"dspxor_ck",	&dspxor_ck,	CK_16XX | CK_1510 | CK_310),
-	CLK(NULL,	"dsptim_ck",	&dsptim_ck,	CK_16XX | CK_1510 | CK_310),
+	CLK(NULL,	"dsp_ck",	&dsp_ck.hw,	CK_16XX | CK_1510 | CK_310),
+	CLK(NULL,	"dspmmu_ck",	&dspmmu_ck.hw,	CK_16XX | CK_1510 | CK_310),
+	CLK(NULL,	"dspper_ck",	&dspper_ck.hw,	CK_16XX | CK_1510 | CK_310),
+	CLK(NULL,	"dspxor_ck",	&dspxor_ck.hw,	CK_16XX | CK_1510 | CK_310),
+	CLK(NULL,	"dsptim_ck",	&dsptim_ck.hw,	CK_16XX | CK_1510 | CK_310),
 	/* CK_GEN3 clocks */
-	CLK(NULL,	"tc_ck",	&tc_ck.clk,	CK_16XX | CK_1510 | CK_310 | CK_7XX),
-	CLK(NULL,	"tipb_ck",	&tipb_ck,	CK_1510 | CK_310),
-	CLK(NULL,	"l3_ocpi_ck",	&l3_ocpi_ck,	CK_16XX | CK_7XX),
-	CLK(NULL,	"tc1_ck",	&tc1_ck,	CK_16XX),
-	CLK(NULL,	"tc2_ck",	&tc2_ck,	CK_16XX),
-	CLK(NULL,	"dma_ck",	&dma_ck,	CK_16XX | CK_1510 | CK_310),
-	CLK(NULL,	"dma_lcdfree_ck", &dma_lcdfree_ck, CK_16XX),
-	CLK(NULL,	"api_ck",	&api_ck.clk,	CK_16XX | CK_1510 | CK_310 | CK_7XX),
-	CLK(NULL,	"lb_ck",	&lb_ck.clk,	CK_1510 | CK_310),
-	CLK(NULL,	"rhea1_ck",	&rhea1_ck,	CK_16XX),
-	CLK(NULL,	"rhea2_ck",	&rhea2_ck,	CK_16XX),
-	CLK(NULL,	"lcd_ck",	&lcd_ck_16xx,	CK_16XX | CK_7XX),
-	CLK(NULL,	"lcd_ck",	&lcd_ck_1510.clk, CK_1510 | CK_310),
+	CLK(NULL,	"tc_ck",	&tc_ck.clk.hw,	CK_16XX | CK_1510 | CK_310 | CK_7XX),
+	CLK(NULL,	"tipb_ck",	&tipb_ck.hw,	CK_1510 | CK_310),
+	CLK(NULL,	"l3_ocpi_ck",	&l3_ocpi_ck.hw,	CK_16XX | CK_7XX),
+	CLK(NULL,	"tc1_ck",	&tc1_ck.hw,	CK_16XX),
+	CLK(NULL,	"tc2_ck",	&tc2_ck.hw,	CK_16XX),
+	CLK(NULL,	"dma_ck",	&dma_ck.hw,	CK_16XX | CK_1510 | CK_310),
+	CLK(NULL,	"dma_lcdfree_ck", &dma_lcdfree_ck.hw, CK_16XX),
+	CLK(NULL,	"api_ck",	&api_ck.clk.hw,	CK_16XX | CK_1510 | CK_310 | CK_7XX),
+	CLK(NULL,	"lb_ck",	&lb_ck.clk.hw,	CK_1510 | CK_310),
+	CLK(NULL,	"rhea1_ck",	&rhea1_ck.hw,	CK_16XX),
+	CLK(NULL,	"rhea2_ck",	&rhea2_ck.hw,	CK_16XX),
+	CLK(NULL,	"lcd_ck",	&lcd_ck_16xx.hw, CK_16XX | CK_7XX),
+	CLK(NULL,	"lcd_ck",	&lcd_ck_1510.clk.hw, CK_1510 | CK_310),
 	/* ULPD clocks */
-	CLK(NULL,	"uart1_ck",	&uart1_1510,	CK_1510 | CK_310),
-	CLK(NULL,	"uart1_ck",	&uart1_16xx.clk, CK_16XX),
-	CLK(NULL,	"uart1_ck",	&uart1_7xx,	CK_7XX),
-	CLK(NULL,	"uart2_ck",	&uart2_ck,	CK_16XX | CK_1510 | CK_310),
-	CLK(NULL,	"uart2_ck",	&uart2_7xx,	CK_7XX),
-	CLK(NULL,	"uart3_ck",	&uart3_1510,	CK_1510 | CK_310),
-	CLK(NULL,	"uart3_ck",	&uart3_16xx.clk, CK_16XX),
-	CLK(NULL,	"usb_clko",	&usb_clko,	CK_16XX | CK_1510 | CK_310),
-	CLK(NULL,	"usb_hhc_ck",	&usb_hhc_ck1510, CK_1510 | CK_310),
-	CLK(NULL,	"usb_hhc_ck",	&usb_hhc_ck16xx, CK_16XX),
-	CLK(NULL,	"usb_dc_ck",	&usb_dc_ck,	CK_16XX | CK_7XX),
-	CLK(NULL,	"mclk",		&mclk_1510,	CK_1510 | CK_310),
-	CLK(NULL,	"mclk",		&mclk_16xx,	CK_16XX),
-	CLK(NULL,	"bclk",		&bclk_1510,	CK_1510 | CK_310),
-	CLK(NULL,	"bclk",		&bclk_16xx,	CK_16XX),
-	CLK("mmci-omap.0", "fck",	&mmc1_ck,	CK_16XX | CK_1510 | CK_310),
-	CLK("mmci-omap.0", "fck",	&mmc3_ck,	CK_7XX),
-	CLK("mmci-omap.0", "ick",	&armper_ck.clk,	CK_16XX | CK_1510 | CK_310 | CK_7XX),
-	CLK("mmci-omap.1", "fck",	&mmc2_ck,	CK_16XX),
-	CLK("mmci-omap.1", "ick",	&armper_ck.clk,	CK_16XX),
+	CLK(NULL,	"uart1_ck",	&uart1_1510.hw,	CK_1510 | CK_310),
+	CLK(NULL,	"uart1_ck",	&uart1_16xx.clk.hw, CK_16XX),
+	CLK(NULL,	"uart1_ck",	&uart1_7xx.hw,	CK_7XX),
+	CLK(NULL,	"uart2_ck",	&uart2_ck.hw,	CK_16XX | CK_1510 | CK_310),
+	CLK(NULL,	"uart2_ck",	&uart2_7xx.hw,	CK_7XX),
+	CLK(NULL,	"uart3_ck",	&uart3_1510.hw,	CK_1510 | CK_310),
+	CLK(NULL,	"uart3_ck",	&uart3_16xx.clk.hw, CK_16XX),
+	CLK(NULL,	"usb_clko",	&usb_clko.hw,	CK_16XX | CK_1510 | CK_310),
+	CLK(NULL,	"usb_hhc_ck",	&usb_hhc_ck1510.hw, CK_1510 | CK_310),
+	CLK(NULL,	"usb_hhc_ck",	&usb_hhc_ck16xx.hw, CK_16XX),
+	CLK(NULL,	"usb_dc_ck",	&usb_dc_ck.hw,	CK_16XX | CK_7XX),
+	CLK(NULL,	"mclk",		&mclk_1510.hw,	CK_1510 | CK_310),
+	CLK(NULL,	"mclk",		&mclk_16xx.hw,	CK_16XX),
+	CLK(NULL,	"bclk",		&bclk_1510.hw,	CK_1510 | CK_310),
+	CLK(NULL,	"bclk",		&bclk_16xx.hw,	CK_16XX),
+	CLK("mmci-omap.0", "fck",	&mmc1_ck.hw,	CK_16XX | CK_1510 | CK_310),
+	CLK("mmci-omap.0", "fck",	&mmc3_ck.hw,	CK_7XX),
+	CLK("mmci-omap.0", "ick",	&armper_ck.clk.hw, CK_16XX | CK_1510 | CK_310 | CK_7XX),
+	CLK("mmci-omap.1", "fck",	&mmc2_ck.hw,	CK_16XX),
+	CLK("mmci-omap.1", "ick",	&armper_ck.clk.hw, CK_16XX),
 	/* Virtual clocks */
-	CLK(NULL,	"mpu",		&virtual_ck_mpu, CK_16XX | CK_1510 | CK_310),
-	CLK("omap_i2c.1", "fck",	&i2c_fck,	CK_16XX | CK_1510 | CK_310 | CK_7XX),
-	CLK("omap_i2c.1", "ick",	&i2c_ick,	CK_16XX),
-	CLK("omap_i2c.1", "ick",	&dummy_ck,	CK_1510 | CK_310 | CK_7XX),
-	CLK("omap1_spi100k.1", "fck",	&dummy_ck,	CK_7XX),
-	CLK("omap1_spi100k.1", "ick",	&dummy_ck,	CK_7XX),
-	CLK("omap1_spi100k.2", "fck",	&dummy_ck,	CK_7XX),
-	CLK("omap1_spi100k.2", "ick",	&dummy_ck,	CK_7XX),
-	CLK("omap_uwire", "fck",	&armxor_ck.clk,	CK_16XX | CK_1510 | CK_310),
-	CLK("omap-mcbsp.1", "ick",	&dspper_ck,	CK_16XX),
-	CLK("omap-mcbsp.1", "ick",	&dummy_ck,	CK_1510 | CK_310),
-	CLK("omap-mcbsp.2", "ick",	&armper_ck.clk,	CK_16XX),
-	CLK("omap-mcbsp.2", "ick",	&dummy_ck,	CK_1510 | CK_310),
-	CLK("omap-mcbsp.3", "ick",	&dspper_ck,	CK_16XX),
-	CLK("omap-mcbsp.3", "ick",	&dummy_ck,	CK_1510 | CK_310),
-	CLK("omap-mcbsp.1", "fck",	&dspxor_ck,	CK_16XX | CK_1510 | CK_310),
-	CLK("omap-mcbsp.2", "fck",	&armper_ck.clk,	CK_16XX | CK_1510 | CK_310),
-	CLK("omap-mcbsp.3", "fck",	&dspxor_ck,	CK_16XX | CK_1510 | CK_310),
+	CLK(NULL,	"mpu",		&virtual_ck_mpu.hw, CK_16XX | CK_1510 | CK_310),
+	CLK("omap_i2c.1", "fck",	&i2c_fck.hw,	CK_16XX | CK_1510 | CK_310 | CK_7XX),
+	CLK("omap_i2c.1", "ick",	&i2c_ick.hw,	CK_16XX),
+	CLK("omap_i2c.1", "ick",	&dummy_ck.hw,	CK_1510 | CK_310 | CK_7XX),
+	CLK("omap1_spi100k.1", "fck",	&dummy_ck.hw,	CK_7XX),
+	CLK("omap1_spi100k.1", "ick",	&dummy_ck.hw,	CK_7XX),
+	CLK("omap1_spi100k.2", "fck",	&dummy_ck.hw,	CK_7XX),
+	CLK("omap1_spi100k.2", "ick",	&dummy_ck.hw,	CK_7XX),
+	CLK("omap_uwire", "fck",	&armxor_ck.clk.hw, CK_16XX | CK_1510 | CK_310),
+	CLK("omap-mcbsp.1", "ick",	&dspper_ck.hw,	CK_16XX),
+	CLK("omap-mcbsp.1", "ick",	&dummy_ck.hw,	CK_1510 | CK_310),
+	CLK("omap-mcbsp.2", "ick",	&armper_ck.clk.hw, CK_16XX),
+	CLK("omap-mcbsp.2", "ick",	&dummy_ck.hw,	CK_1510 | CK_310),
+	CLK("omap-mcbsp.3", "ick",	&dspper_ck.hw,	CK_16XX),
+	CLK("omap-mcbsp.3", "ick",	&dummy_ck.hw,	CK_1510 | CK_310),
+	CLK("omap-mcbsp.1", "fck",	&dspxor_ck.hw,	CK_16XX | CK_1510 | CK_310),
+	CLK("omap-mcbsp.2", "fck",	&armper_ck.clk.hw, CK_16XX | CK_1510 | CK_310),
+	CLK("omap-mcbsp.3", "fck",	&dspxor_ck.hw,	CK_16XX | CK_1510 | CK_310),
 };
 
 /*
@@ -763,15 +694,14 @@ u32 cpu_mask;
 int __init omap1_clk_init(void)
 {
 	struct omap_clk *c;
-	int crystal_type = 0; /* Default 12 MHz */
 	u32 reg;
 
 #ifdef CONFIG_DEBUG_LL
-	/*
-	 * Resets some clocks that may be left on from bootloader,
-	 * but leaves serial clocks on.
-	 */
-	omap_writel(0x3 << 29, MOD_CONF_CTRL_0);
+	/* Make sure UART clocks are enabled early */
+	if (cpu_is_omap16xx())
+		omap_writel(omap_readl(MOD_CONF_CTRL_0) |
+			    CONF_MOD_UART1_CLK_MODE_R |
+			    CONF_MOD_UART3_CLK_MODE_R, MOD_CONF_CTRL_0);
 #endif
 
 	/* USB_REQ_EN will be disabled later if necessary (usb_dc_ck) */
@@ -783,9 +713,6 @@ int __init omap1_clk_init(void)
 	/* By default all idlect1 clocks are allowed to idle */
 	arm_idlect1_mask = ~0;
 
-	for (c = omap_clks; c < omap_clks + ARRAY_SIZE(omap_clks); c++)
-		clk_preinit(c->lk.clk);
-
 	cpu_mask = 0;
 	if (cpu_is_omap1710())
 		cpu_mask |= CK_1710;
@@ -798,27 +725,19 @@ int __init omap1_clk_init(void)
 	if (cpu_is_omap310())
 		cpu_mask |= CK_310;
 
-	for (c = omap_clks; c < omap_clks + ARRAY_SIZE(omap_clks); c++)
-		if (c->cpu & cpu_mask) {
-			clkdev_add(&c->lk);
-			clk_register(c->lk.clk);
-		}
-
 	/* Pointers to these clocks are needed by code in clock.c */
-	api_ck_p = clk_get(NULL, "api_ck");
-	ck_dpll1_p = clk_get(NULL, "ck_dpll1");
-	ck_ref_p = clk_get(NULL, "ck_ref");
+	api_ck_p = &api_ck.clk;
+	ck_dpll1_p = &ck_dpll1;
+	ck_ref_p = &ck_ref;
 
 	if (cpu_is_omap7xx())
 		ck_ref.rate = 13000000;
-	if (cpu_is_omap16xx() && crystal_type == 2)
-		ck_ref.rate = 19200000;
 
 	pr_info("Clocks: ARM_SYSST: 0x%04x DPLL_CTL: 0x%04x ARM_CKCTL: 0x%04x\n",
 		omap_readw(ARM_SYSST), omap_readw(DPLL_CTL),
 		omap_readw(ARM_CKCTL));
 
-	/* We want to be in syncronous scalable mode */
+	/* We want to be in synchronous scalable mode */
 	omap_writew(0x1000, ARM_SYSST);
 
 
@@ -851,10 +770,7 @@ int __init omap1_clk_init(void)
 			}
 		}
 	}
-	propagate_rate(&ck_dpll1);
-	/* Cache rates for clocks connected to ck_ref (not dpll1) */
-	propagate_rate(&ck_ref);
-	omap1_show_rates();
+
 	if (machine_is_omap_perseus2() || machine_is_omap_fsample()) {
 		/* Select slicer output as OMAP input clock */
 		omap_writew(omap_readw(OMAP7XX_PCC_UPLD_CTRL) & ~0x1,
@@ -886,16 +802,28 @@ int __init omap1_clk_init(void)
 	 */
 	omap_writew(0x0000, ARM_IDLECT2);	/* Turn LCD clock off also */
 
-	/*
-	 * Only enable those clocks we will need, let the drivers
-	 * enable other clocks as necessary
-	 */
-	clk_enable(&armper_ck.clk);
-	clk_enable(&armxor_ck.clk);
-	clk_enable(&armtim_ck.clk); /* This should be done by timer code */
+	for (c = omap_clks; c < omap_clks + ARRAY_SIZE(omap_clks); c++) {
+		if (!(c->cpu & cpu_mask))
+			continue;
+
+		if (c->lk.clk_hw->init) { /* NULL if provider already registered */
+			const struct clk_init_data *init = c->lk.clk_hw->init;
+			const char *name = c->lk.clk_hw->init->name;
+			int err;
+
+			err = clk_hw_register(NULL, c->lk.clk_hw);
+			if (err < 0) {
+				pr_err("failed to register clock \"%s\"! (%d)\n", name, err);
+				/* may be tried again, restore init data */
+				c->lk.clk_hw->init = init;
+				continue;
+			}
+		}
+
+		clk_hw_register_clkdev(c->lk.clk_hw, c->lk.con_id, c->lk.dev_id);
+	}
 
-	if (cpu_is_omap15xx())
-		clk_enable(&arm_gpio_ck);
+	omap1_show_rates();
 
 	return 0;
 }
@@ -907,7 +835,7 @@ void __init omap1_clk_late_init(void)
 	unsigned long rate = ck_dpll1.rate;
 
 	/* Find the highest supported frequency and enable it */
-	if (omap1_select_table_rate(&virtual_ck_mpu, ~0)) {
+	if (omap1_select_table_rate(&virtual_ck_mpu, ~0, arm_ck.rate)) {
 		pr_err("System frequencies not set, using default. Check your config.\n");
 		/*
 		 * Reprogramming the DPLL is tricky, it must be done from SRAM.
diff --git a/arch/arm/mach-omap1/common.h b/arch/arm/mach-omap1/common.h
index 504b959ba5cf..5ceff05e15c0 100644
--- a/arch/arm/mach-omap1/common.h
+++ b/arch/arm/mach-omap1/common.h
@@ -31,8 +31,7 @@
 
 #include <asm/exception.h>
 
-#include <mach/irqs.h>
-
+#include "irqs.h"
 #include "soc.h"
 #include "i2c.h"
 
diff --git a/arch/arm/mach-omap1/devices.c b/arch/arm/mach-omap1/devices.c
index eb0f09edb3d1..80e94770582a 100644
--- a/arch/arm/mach-omap1/devices.c
+++ b/arch/arm/mach-omap1/devices.c
@@ -14,15 +14,15 @@
 #include <linux/spi/spi.h>
 
 #include <linux/platform_data/omap-wd-timer.h>
+#include <linux/soc/ti/omap1-io.h>
 
 #include <asm/mach/map.h>
 
-#include <mach/tc.h>
-#include <mach/mux.h>
-
-#include <mach/omap7xx.h>
-#include <mach/hardware.h>
+#include "tc.h"
+#include "mux.h"
 
+#include "omap7xx.h"
+#include "hardware.h"
 #include "common.h"
 #include "clock.h"
 #include "mmc.h"
@@ -356,7 +356,7 @@ static int __init omap1_init_devices(void)
 	if (!cpu_class_is_omap1())
 		return -ENODEV;
 
-	omap_sram_init();
+	omap1_sram_init();
 	omap1_clk_late_init();
 
 	/* please keep these calls, and their implementations above,
diff --git a/arch/arm/mach-omap1/dma.c b/arch/arm/mach-omap1/dma.c
index 2bf659fb6099..c3f280c3c5d7 100644
--- a/arch/arm/mach-omap1/dma.c
+++ b/arch/arm/mach-omap1/dma.c
@@ -24,7 +24,7 @@
 #include <linux/dma-mapping.h>
 #include <linux/dmaengine.h>
 #include <linux/omap-dma.h>
-#include <mach/tc.h>
+#include "tc.h"
 
 #include "soc.h"
 
diff --git a/arch/arm/mach-omap1/fb.c b/arch/arm/mach-omap1/fb.c
index 0e32a959f254..b6e952b03838 100644
--- a/arch/arm/mach-omap1/fb.c
+++ b/arch/arm/mach-omap1/fb.c
@@ -17,9 +17,12 @@
 #include <linux/io.h>
 #include <linux/omapfb.h>
 #include <linux/dma-mapping.h>
+#include <linux/irq.h>
 
 #include <asm/mach/map.h>
 
+#include "irqs.h"
+
 #if IS_ENABLED(CONFIG_FB_OMAP)
 
 static bool omapfb_lcd_configured;
@@ -27,6 +30,19 @@ static struct omapfb_platform_data omapfb_config;
 
 static u64 omap_fb_dma_mask = ~(u32)0;
 
+static struct resource omap_fb_resources[] = {
+	{
+		.name  = "irq",
+		.start = INT_LCD_CTRL,
+		.flags = IORESOURCE_IRQ,
+	},
+	{
+		.name  = "irq",
+		.start = INT_SOSSI_MATCH,
+		.flags = IORESOURCE_IRQ,
+	},
+};
+
 static struct platform_device omap_fb_device = {
 	.name		= "omapfb",
 	.id		= -1,
@@ -35,7 +51,8 @@ static struct platform_device omap_fb_device = {
 		.coherent_dma_mask	= DMA_BIT_MASK(32),
 		.platform_data		= &omapfb_config,
 	},
-	.num_resources = 0,
+	.num_resources = ARRAY_SIZE(omap_fb_resources),
+	.resource = omap_fb_resources,
 };
 
 void __init omapfb_set_lcd_config(const struct omap_lcd_config *config)
diff --git a/arch/arm/mach-omap1/flash.c b/arch/arm/mach-omap1/flash.c
index 40e43ce5329f..0a3ddb3b66eb 100644
--- a/arch/arm/mach-omap1/flash.c
+++ b/arch/arm/mach-omap1/flash.c
@@ -6,11 +6,12 @@
 #include <linux/io.h>
 #include <linux/mtd/mtd.h>
 #include <linux/mtd/map.h>
+#include <linux/soc/ti/omap1-io.h>
+
+#include "tc.h"
 
-#include <mach/tc.h>
 #include "flash.h"
 
-#include <mach/hardware.h>
 
 void omap1_set_vpp(struct platform_device *pdev, int enable)
 {
diff --git a/arch/arm/mach-omap1/fpga.c b/arch/arm/mach-omap1/fpga.c
index f03ed523f20f..4c71a195969f 100644
--- a/arch/arm/mach-omap1/fpga.c
+++ b/arch/arm/mach-omap1/fpga.c
@@ -24,8 +24,7 @@
 #include <asm/irq.h>
 #include <asm/mach/irq.h>
 
-#include <mach/hardware.h>
-
+#include "hardware.h"
 #include "iomap.h"
 #include "common.h"
 #include "fpga.h"
diff --git a/arch/arm/mach-omap1/gpio15xx.c b/arch/arm/mach-omap1/gpio15xx.c
index 3ec08bd5d8a0..c675f11de99d 100644
--- a/arch/arm/mach-omap1/gpio15xx.c
+++ b/arch/arm/mach-omap1/gpio15xx.c
@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * OMAP15xx specific gpio init
  *
@@ -5,21 +6,13 @@
  *
  * Author:
  *	Charulatha V <charu@ti.com>
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation version 2.
- *
- * This program is distributed "as is" WITHOUT ANY WARRANTY of any
- * kind, whether express or implied; without even the implied warranty
- * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
  */
 
 #include <linux/gpio.h>
 #include <linux/platform_data/gpio-omap.h>
+#include <linux/soc/ti/omap1-soc.h>
 
-#include <mach/irqs.h>
+#include "irqs.h"
 
 #define OMAP1_MPUIO_VBASE		OMAP1_MPUIO_BASE
 #define OMAP1510_GPIO_BASE		0xFFFCE000
diff --git a/arch/arm/mach-omap1/gpio16xx.c b/arch/arm/mach-omap1/gpio16xx.c
index 500cfd416c42..cf052714b3f8 100644
--- a/arch/arm/mach-omap1/gpio16xx.c
+++ b/arch/arm/mach-omap1/gpio16xx.c
@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * OMAP16xx specific gpio init
  *
@@ -5,22 +6,14 @@
  *
  * Author:
  *	Charulatha V <charu@ti.com>
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation version 2.
- *
- * This program is distributed "as is" WITHOUT ANY WARRANTY of any
- * kind, whether express or implied; without even the implied warranty
- * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
  */
 
 #include <linux/gpio.h>
 #include <linux/platform_data/gpio-omap.h>
+#include <linux/soc/ti/omap1-io.h>
 
-#include <mach/irqs.h>
-
+#include "hardware.h"
+#include "irqs.h"
 #include "soc.h"
 
 #define OMAP1610_GPIO1_BASE		0xfffbe400
diff --git a/arch/arm/mach-omap1/gpio7xx.c b/arch/arm/mach-omap1/gpio7xx.c
index aeb81c18ffcc..c372b357eab4 100644
--- a/arch/arm/mach-omap1/gpio7xx.c
+++ b/arch/arm/mach-omap1/gpio7xx.c
@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * OMAP7xx specific gpio init
  *
@@ -5,22 +6,12 @@
  *
  * Author:
  *	Charulatha V <charu@ti.com>
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation version 2.
- *
- * This program is distributed "as is" WITHOUT ANY WARRANTY of any
- * kind, whether express or implied; without even the implied warranty
- * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
  */
 
 #include <linux/gpio.h>
 #include <linux/platform_data/gpio-omap.h>
 
-#include <mach/irqs.h>
-
+#include "irqs.h"
 #include "soc.h"
 
 #define OMAP7XX_GPIO1_BASE		0xfffbc000
diff --git a/arch/arm/mach-omap1/hardware.h b/arch/arm/mach-omap1/hardware.h
new file mode 100644
index 000000000000..c228234a1ed4
--- /dev/null
+++ b/arch/arm/mach-omap1/hardware.h
@@ -0,0 +1,195 @@
+/*
+ * Hardware definitions for TI OMAP processors and boards
+ *
+ * NOTE: Please put device driver specific defines into a separate header
+ *	 file for each driver.
+ *
+ * Copyright (C) 2001 RidgeRun, Inc.
+ * Author: RidgeRun, Inc. Greg Lonnon <glonnon@ridgerun.com>
+ *
+ * Reorganized for Linux-2.6 by Tony Lindgren <tony@atomide.com>
+ *                          and Dirk Behme <dirk.behme@de.bosch.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License as published by the
+ * Free Software Foundation; either version 2 of the License, or (at your
+ * option) any later version.
+ *
+ * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
+ * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
+ * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
+ * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
+ * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
+ * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
+ * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
+ * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
+ * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program; if not, write to the Free Software Foundation, Inc.,
+ * 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#ifndef __ASM_ARCH_OMAP_HARDWARE_H
+#define __ASM_ARCH_OMAP_HARDWARE_H
+
+#include <linux/sizes.h>
+#include <linux/soc/ti/omap1-io.h>
+#ifndef __ASSEMBLER__
+#include <asm/types.h>
+#include <linux/soc/ti/omap1-soc.h>
+
+#include "tc.h"
+
+/* Almost all documentation for chip and board memory maps assumes
+ * BM is clear.  Most devel boards have a switch to control booting
+ * from NOR flash (using external chipselect 3) rather than mask ROM,
+ * which uses BM to interchange the physical CS0 and CS3 addresses.
+ */
+static inline u32 omap_cs0m_phys(void)
+{
+	return (omap_readl(EMIFS_CONFIG) & OMAP_EMIFS_CONFIG_BM)
+			?  OMAP_CS3_PHYS : 0;
+}
+
+static inline u32 omap_cs3_phys(void)
+{
+	return (omap_readl(EMIFS_CONFIG) & OMAP_EMIFS_CONFIG_BM)
+			? 0 : OMAP_CS3_PHYS;
+}
+
+#endif	/* ifndef __ASSEMBLER__ */
+
+#define OMAP1_IO_OFFSET		0x00f00000	/* Virtual IO = 0xff0b0000 */
+#define OMAP1_IO_ADDRESS(pa)	IOMEM((pa) - OMAP1_IO_OFFSET)
+
+#include "serial.h"
+
+/*
+ * ---------------------------------------------------------------------------
+ * Common definitions for all OMAP processors
+ * NOTE: Put all processor or board specific parts to the special header
+ *	 files.
+ * ---------------------------------------------------------------------------
+ */
+
+/*
+ * ----------------------------------------------------------------------------
+ * Timers
+ * ----------------------------------------------------------------------------
+ */
+#define OMAP_MPU_TIMER1_BASE	(0xfffec500)
+#define OMAP_MPU_TIMER2_BASE	(0xfffec600)
+#define OMAP_MPU_TIMER3_BASE	(0xfffec700)
+#define MPU_TIMER_FREE		(1 << 6)
+#define MPU_TIMER_CLOCK_ENABLE	(1 << 5)
+#define MPU_TIMER_AR		(1 << 1)
+#define MPU_TIMER_ST		(1 << 0)
+
+/*
+ * ---------------------------------------------------------------------------
+ * Watchdog timer
+ * ---------------------------------------------------------------------------
+ */
+
+/* Watchdog timer within the OMAP3.2 gigacell */
+#define OMAP_MPU_WATCHDOG_BASE	(0xfffec800)
+#define OMAP_WDT_TIMER		(OMAP_MPU_WATCHDOG_BASE + 0x0)
+#define OMAP_WDT_LOAD_TIM	(OMAP_MPU_WATCHDOG_BASE + 0x4)
+#define OMAP_WDT_READ_TIM	(OMAP_MPU_WATCHDOG_BASE + 0x4)
+#define OMAP_WDT_TIMER_MODE	(OMAP_MPU_WATCHDOG_BASE + 0x8)
+
+/*
+ * ---------------------------------------------------------------------------
+ * Interrupts
+ * ---------------------------------------------------------------------------
+ */
+#ifdef CONFIG_ARCH_OMAP1
+
+/*
+ * XXX: These probably want to be moved to arch/arm/mach-omap/omap1/irq.c
+ * or something similar.. -- PFM.
+ */
+
+#define OMAP_IH1_BASE		0xfffecb00
+#define OMAP_IH2_BASE		0xfffe0000
+
+#define OMAP_IH1_ITR		(OMAP_IH1_BASE + 0x00)
+#define OMAP_IH1_MIR		(OMAP_IH1_BASE + 0x04)
+#define OMAP_IH1_SIR_IRQ	(OMAP_IH1_BASE + 0x10)
+#define OMAP_IH1_SIR_FIQ	(OMAP_IH1_BASE + 0x14)
+#define OMAP_IH1_CONTROL	(OMAP_IH1_BASE + 0x18)
+#define OMAP_IH1_ILR0		(OMAP_IH1_BASE + 0x1c)
+#define OMAP_IH1_ISR		(OMAP_IH1_BASE + 0x9c)
+
+#define OMAP_IH2_ITR		(OMAP_IH2_BASE + 0x00)
+#define OMAP_IH2_MIR		(OMAP_IH2_BASE + 0x04)
+#define OMAP_IH2_SIR_IRQ	(OMAP_IH2_BASE + 0x10)
+#define OMAP_IH2_SIR_FIQ	(OMAP_IH2_BASE + 0x14)
+#define OMAP_IH2_CONTROL	(OMAP_IH2_BASE + 0x18)
+#define OMAP_IH2_ILR0		(OMAP_IH2_BASE + 0x1c)
+#define OMAP_IH2_ISR		(OMAP_IH2_BASE + 0x9c)
+
+#define IRQ_ITR_REG_OFFSET	0x00
+#define IRQ_MIR_REG_OFFSET	0x04
+#define IRQ_SIR_IRQ_REG_OFFSET	0x10
+#define IRQ_SIR_FIQ_REG_OFFSET	0x14
+#define IRQ_CONTROL_REG_OFFSET	0x18
+#define IRQ_ISR_REG_OFFSET	0x9c
+#define IRQ_ILR0_REG_OFFSET	0x1c
+#define IRQ_GMR_REG_OFFSET	0xa0
+
+#endif
+
+/* Timer32K for 1610 and 1710*/
+#define OMAP_TIMER32K_BASE	0xFFFBC400
+
+/*
+ * ---------------------------------------------------------------------------
+ * TIPB bus interface
+ * ---------------------------------------------------------------------------
+ */
+#define TIPB_PUBLIC_CNTL_BASE		0xfffed300
+#define MPU_PUBLIC_TIPB_CNTL		(TIPB_PUBLIC_CNTL_BASE + 0x8)
+#define TIPB_PRIVATE_CNTL_BASE		0xfffeca00
+#define MPU_PRIVATE_TIPB_CNTL		(TIPB_PRIVATE_CNTL_BASE + 0x8)
+
+/*
+ * ----------------------------------------------------------------------------
+ * MPUI interface
+ * ----------------------------------------------------------------------------
+ */
+#define MPUI_BASE			(0xfffec900)
+#define MPUI_CTRL			(MPUI_BASE + 0x0)
+#define MPUI_DEBUG_ADDR			(MPUI_BASE + 0x4)
+#define MPUI_DEBUG_DATA			(MPUI_BASE + 0x8)
+#define MPUI_DEBUG_FLAG			(MPUI_BASE + 0xc)
+#define MPUI_STATUS_REG			(MPUI_BASE + 0x10)
+#define MPUI_DSP_STATUS			(MPUI_BASE + 0x14)
+#define MPUI_DSP_BOOT_CONFIG		(MPUI_BASE + 0x18)
+#define MPUI_DSP_API_CONFIG		(MPUI_BASE + 0x1c)
+
+/*
+ * ----------------------------------------------------------------------------
+ * LED Pulse Generator
+ * ----------------------------------------------------------------------------
+ */
+#define OMAP_LPG1_BASE			0xfffbd000
+#define OMAP_LPG2_BASE			0xfffbd800
+#define OMAP_LPG1_LCR			(OMAP_LPG1_BASE + 0x00)
+#define OMAP_LPG1_PMR			(OMAP_LPG1_BASE + 0x04)
+#define OMAP_LPG2_LCR			(OMAP_LPG2_BASE + 0x00)
+#define OMAP_LPG2_PMR			(OMAP_LPG2_BASE + 0x04)
+
+/*
+ * ---------------------------------------------------------------------------
+ * Processor specific defines
+ * ---------------------------------------------------------------------------
+ */
+
+#include "omap7xx.h"
+#include "omap1510.h"
+#include "omap16xx.h"
+
+#endif	/* __ASM_ARCH_OMAP_HARDWARE_H */
diff --git a/arch/arm/mach-omap1/i2c.c b/arch/arm/mach-omap1/i2c.c
index 5e6d81b1624c..22f945360599 100644
--- a/arch/arm/mach-omap1/i2c.c
+++ b/arch/arm/mach-omap1/i2c.c
@@ -7,8 +7,10 @@
 
 #include <linux/i2c.h>
 #include <linux/platform_data/i2c-omap.h>
-#include <mach/mux.h>
+
+#include "mux.h"
 #include "soc.h"
+#include "i2c.h"
 
 #define OMAP_I2C_SIZE		0x3f
 #define OMAP1_I2C_BASE		0xfffb3800
diff --git a/arch/arm/mach-omap1/id.c b/arch/arm/mach-omap1/id.c
index 91556e374152..c3bb1b71fdf3 100644
--- a/arch/arm/mach-omap1/id.c
+++ b/arch/arm/mach-omap1/id.c
@@ -12,12 +12,11 @@
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/io.h>
+#include <linux/soc/ti/omap1-io.h>
 #include <asm/system_info.h>
 
 #include "soc.h"
-
-#include <mach/hardware.h>
-
+#include "hardware.h"
 #include "common.h"
 
 #define OMAP_DIE_ID_0		0xfffe1800
diff --git a/arch/arm/mach-omap1/include/mach/hardware.h b/arch/arm/mach-omap1/include/mach/hardware.h
deleted file mode 100644
index e7c8ac7d83e3..000000000000
--- a/arch/arm/mach-omap1/include/mach/hardware.h
+++ /dev/null
@@ -1,321 +0,0 @@
-/*
- * arch/arm/mach-omap1/include/mach/hardware.h
- *
- * Hardware definitions for TI OMAP processors and boards
- *
- * NOTE: Please put device driver specific defines into a separate header
- *	 file for each driver.
- *
- * Copyright (C) 2001 RidgeRun, Inc.
- * Author: RidgeRun, Inc. Greg Lonnon <glonnon@ridgerun.com>
- *
- * Reorganized for Linux-2.6 by Tony Lindgren <tony@atomide.com>
- *                          and Dirk Behme <dirk.behme@de.bosch.com>
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
- * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
- * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- */
-
-#ifndef __ASM_ARCH_OMAP_HARDWARE_H
-#define __ASM_ARCH_OMAP_HARDWARE_H
-
-#include <linux/sizes.h>
-#ifndef __ASSEMBLER__
-#include <asm/types.h>
-#include <mach/soc.h>
-
-/*
- * NOTE: Please use ioremap + __raw_read/write where possible instead of these
- */
-extern u8 omap_readb(u32 pa);
-extern u16 omap_readw(u32 pa);
-extern u32 omap_readl(u32 pa);
-extern void omap_writeb(u8 v, u32 pa);
-extern void omap_writew(u16 v, u32 pa);
-extern void omap_writel(u32 v, u32 pa);
-
-#include <mach/tc.h>
-
-/* Almost all documentation for chip and board memory maps assumes
- * BM is clear.  Most devel boards have a switch to control booting
- * from NOR flash (using external chipselect 3) rather than mask ROM,
- * which uses BM to interchange the physical CS0 and CS3 addresses.
- */
-static inline u32 omap_cs0m_phys(void)
-{
-	return (omap_readl(EMIFS_CONFIG) & OMAP_EMIFS_CONFIG_BM)
-			?  OMAP_CS3_PHYS : 0;
-}
-
-static inline u32 omap_cs3_phys(void)
-{
-	return (omap_readl(EMIFS_CONFIG) & OMAP_EMIFS_CONFIG_BM)
-			? 0 : OMAP_CS3_PHYS;
-}
-
-#endif	/* ifndef __ASSEMBLER__ */
-
-#define OMAP1_IO_OFFSET		0x01000000	/* Virtual IO = 0xfefb0000 */
-#define OMAP1_IO_ADDRESS(pa)	IOMEM((pa) - OMAP1_IO_OFFSET)
-
-#include <mach/serial.h>
-
-/*
- * ---------------------------------------------------------------------------
- * Common definitions for all OMAP processors
- * NOTE: Put all processor or board specific parts to the special header
- *	 files.
- * ---------------------------------------------------------------------------
- */
-
-/*
- * ----------------------------------------------------------------------------
- * Timers
- * ----------------------------------------------------------------------------
- */
-#define OMAP_MPU_TIMER1_BASE	(0xfffec500)
-#define OMAP_MPU_TIMER2_BASE	(0xfffec600)
-#define OMAP_MPU_TIMER3_BASE	(0xfffec700)
-#define MPU_TIMER_FREE		(1 << 6)
-#define MPU_TIMER_CLOCK_ENABLE	(1 << 5)
-#define MPU_TIMER_AR		(1 << 1)
-#define MPU_TIMER_ST		(1 << 0)
-
-/*
- * ----------------------------------------------------------------------------
- * Clocks
- * ----------------------------------------------------------------------------
- */
-#define CLKGEN_REG_BASE		(0xfffece00)
-#define ARM_CKCTL		(CLKGEN_REG_BASE + 0x0)
-#define ARM_IDLECT1		(CLKGEN_REG_BASE + 0x4)
-#define ARM_IDLECT2		(CLKGEN_REG_BASE + 0x8)
-#define ARM_EWUPCT		(CLKGEN_REG_BASE + 0xC)
-#define ARM_RSTCT1		(CLKGEN_REG_BASE + 0x10)
-#define ARM_RSTCT2		(CLKGEN_REG_BASE + 0x14)
-#define ARM_SYSST		(CLKGEN_REG_BASE + 0x18)
-#define ARM_IDLECT3		(CLKGEN_REG_BASE + 0x24)
-
-#define CK_RATEF		1
-#define CK_IDLEF		2
-#define CK_ENABLEF		4
-#define CK_SELECTF		8
-#define SETARM_IDLE_SHIFT
-
-/* DPLL control registers */
-#define DPLL_CTL		(0xfffecf00)
-
-/* DSP clock control. Must use __raw_readw() and __raw_writew() with these */
-#define DSP_CONFIG_REG_BASE     IOMEM(0xe1008000)
-#define DSP_CKCTL		(DSP_CONFIG_REG_BASE + 0x0)
-#define DSP_IDLECT1		(DSP_CONFIG_REG_BASE + 0x4)
-#define DSP_IDLECT2		(DSP_CONFIG_REG_BASE + 0x8)
-#define DSP_RSTCT2		(DSP_CONFIG_REG_BASE + 0x14)
-
-/*
- * ---------------------------------------------------------------------------
- * UPLD
- * ---------------------------------------------------------------------------
- */
-#define ULPD_REG_BASE		(0xfffe0800)
-#define ULPD_IT_STATUS		(ULPD_REG_BASE + 0x14)
-#define ULPD_SETUP_ANALOG_CELL_3	(ULPD_REG_BASE + 0x24)
-#define ULPD_CLOCK_CTRL		(ULPD_REG_BASE + 0x30)
-#	define DIS_USB_PVCI_CLK		(1 << 5)	/* no USB/FAC synch */
-#	define USB_MCLK_EN		(1 << 4)	/* enable W4_USB_CLKO */
-#define ULPD_SOFT_REQ		(ULPD_REG_BASE + 0x34)
-#	define SOFT_UDC_REQ		(1 << 4)
-#	define SOFT_USB_CLK_REQ		(1 << 3)
-#	define SOFT_DPLL_REQ		(1 << 0)
-#define ULPD_DPLL_CTRL		(ULPD_REG_BASE + 0x3c)
-#define ULPD_STATUS_REQ		(ULPD_REG_BASE + 0x40)
-#define ULPD_APLL_CTRL		(ULPD_REG_BASE + 0x4c)
-#define ULPD_POWER_CTRL		(ULPD_REG_BASE + 0x50)
-#define ULPD_SOFT_DISABLE_REQ_REG	(ULPD_REG_BASE + 0x68)
-#	define DIS_MMC2_DPLL_REQ	(1 << 11)
-#	define DIS_MMC1_DPLL_REQ	(1 << 10)
-#	define DIS_UART3_DPLL_REQ	(1 << 9)
-#	define DIS_UART2_DPLL_REQ	(1 << 8)
-#	define DIS_UART1_DPLL_REQ	(1 << 7)
-#	define DIS_USB_HOST_DPLL_REQ	(1 << 6)
-#define ULPD_SDW_CLK_DIV_CTRL_SEL	(ULPD_REG_BASE + 0x74)
-#define ULPD_CAM_CLK_CTRL	(ULPD_REG_BASE + 0x7c)
-
-/*
- * ---------------------------------------------------------------------------
- * Watchdog timer
- * ---------------------------------------------------------------------------
- */
-
-/* Watchdog timer within the OMAP3.2 gigacell */
-#define OMAP_MPU_WATCHDOG_BASE	(0xfffec800)
-#define OMAP_WDT_TIMER		(OMAP_MPU_WATCHDOG_BASE + 0x0)
-#define OMAP_WDT_LOAD_TIM	(OMAP_MPU_WATCHDOG_BASE + 0x4)
-#define OMAP_WDT_READ_TIM	(OMAP_MPU_WATCHDOG_BASE + 0x4)
-#define OMAP_WDT_TIMER_MODE	(OMAP_MPU_WATCHDOG_BASE + 0x8)
-
-/*
- * ---------------------------------------------------------------------------
- * Interrupts
- * ---------------------------------------------------------------------------
- */
-#ifdef CONFIG_ARCH_OMAP1
-
-/*
- * XXX: These probably want to be moved to arch/arm/mach-omap/omap1/irq.c
- * or something similar.. -- PFM.
- */
-
-#define OMAP_IH1_BASE		0xfffecb00
-#define OMAP_IH2_BASE		0xfffe0000
-
-#define OMAP_IH1_ITR		(OMAP_IH1_BASE + 0x00)
-#define OMAP_IH1_MIR		(OMAP_IH1_BASE + 0x04)
-#define OMAP_IH1_SIR_IRQ	(OMAP_IH1_BASE + 0x10)
-#define OMAP_IH1_SIR_FIQ	(OMAP_IH1_BASE + 0x14)
-#define OMAP_IH1_CONTROL	(OMAP_IH1_BASE + 0x18)
-#define OMAP_IH1_ILR0		(OMAP_IH1_BASE + 0x1c)
-#define OMAP_IH1_ISR		(OMAP_IH1_BASE + 0x9c)
-
-#define OMAP_IH2_ITR		(OMAP_IH2_BASE + 0x00)
-#define OMAP_IH2_MIR		(OMAP_IH2_BASE + 0x04)
-#define OMAP_IH2_SIR_IRQ	(OMAP_IH2_BASE + 0x10)
-#define OMAP_IH2_SIR_FIQ	(OMAP_IH2_BASE + 0x14)
-#define OMAP_IH2_CONTROL	(OMAP_IH2_BASE + 0x18)
-#define OMAP_IH2_ILR0		(OMAP_IH2_BASE + 0x1c)
-#define OMAP_IH2_ISR		(OMAP_IH2_BASE + 0x9c)
-
-#define IRQ_ITR_REG_OFFSET	0x00
-#define IRQ_MIR_REG_OFFSET	0x04
-#define IRQ_SIR_IRQ_REG_OFFSET	0x10
-#define IRQ_SIR_FIQ_REG_OFFSET	0x14
-#define IRQ_CONTROL_REG_OFFSET	0x18
-#define IRQ_ISR_REG_OFFSET	0x9c
-#define IRQ_ILR0_REG_OFFSET	0x1c
-#define IRQ_GMR_REG_OFFSET	0xa0
-
-#endif
-
-/*
- * ----------------------------------------------------------------------------
- * System control registers
- * ----------------------------------------------------------------------------
- */
-#define MOD_CONF_CTRL_0		0xfffe1080
-#define MOD_CONF_CTRL_1		0xfffe1110
-
-/*
- * ----------------------------------------------------------------------------
- * Pin multiplexing registers
- * ----------------------------------------------------------------------------
- */
-#define FUNC_MUX_CTRL_0		0xfffe1000
-#define FUNC_MUX_CTRL_1		0xfffe1004
-#define FUNC_MUX_CTRL_2		0xfffe1008
-#define COMP_MODE_CTRL_0	0xfffe100c
-#define FUNC_MUX_CTRL_3		0xfffe1010
-#define FUNC_MUX_CTRL_4		0xfffe1014
-#define FUNC_MUX_CTRL_5		0xfffe1018
-#define FUNC_MUX_CTRL_6		0xfffe101C
-#define FUNC_MUX_CTRL_7		0xfffe1020
-#define FUNC_MUX_CTRL_8		0xfffe1024
-#define FUNC_MUX_CTRL_9		0xfffe1028
-#define FUNC_MUX_CTRL_A		0xfffe102C
-#define FUNC_MUX_CTRL_B		0xfffe1030
-#define FUNC_MUX_CTRL_C		0xfffe1034
-#define FUNC_MUX_CTRL_D		0xfffe1038
-#define PULL_DWN_CTRL_0		0xfffe1040
-#define PULL_DWN_CTRL_1		0xfffe1044
-#define PULL_DWN_CTRL_2		0xfffe1048
-#define PULL_DWN_CTRL_3		0xfffe104c
-#define PULL_DWN_CTRL_4		0xfffe10ac
-
-/* OMAP-1610 specific multiplexing registers */
-#define FUNC_MUX_CTRL_E		0xfffe1090
-#define FUNC_MUX_CTRL_F		0xfffe1094
-#define FUNC_MUX_CTRL_10	0xfffe1098
-#define FUNC_MUX_CTRL_11	0xfffe109c
-#define FUNC_MUX_CTRL_12	0xfffe10a0
-#define PU_PD_SEL_0		0xfffe10b4
-#define PU_PD_SEL_1		0xfffe10b8
-#define PU_PD_SEL_2		0xfffe10bc
-#define PU_PD_SEL_3		0xfffe10c0
-#define PU_PD_SEL_4		0xfffe10c4
-
-/* Timer32K for 1610 and 1710*/
-#define OMAP_TIMER32K_BASE	0xFFFBC400
-
-/*
- * ---------------------------------------------------------------------------
- * TIPB bus interface
- * ---------------------------------------------------------------------------
- */
-#define TIPB_PUBLIC_CNTL_BASE		0xfffed300
-#define MPU_PUBLIC_TIPB_CNTL		(TIPB_PUBLIC_CNTL_BASE + 0x8)
-#define TIPB_PRIVATE_CNTL_BASE		0xfffeca00
-#define MPU_PRIVATE_TIPB_CNTL		(TIPB_PRIVATE_CNTL_BASE + 0x8)
-
-/*
- * ----------------------------------------------------------------------------
- * MPUI interface
- * ----------------------------------------------------------------------------
- */
-#define MPUI_BASE			(0xfffec900)
-#define MPUI_CTRL			(MPUI_BASE + 0x0)
-#define MPUI_DEBUG_ADDR			(MPUI_BASE + 0x4)
-#define MPUI_DEBUG_DATA			(MPUI_BASE + 0x8)
-#define MPUI_DEBUG_FLAG			(MPUI_BASE + 0xc)
-#define MPUI_STATUS_REG			(MPUI_BASE + 0x10)
-#define MPUI_DSP_STATUS			(MPUI_BASE + 0x14)
-#define MPUI_DSP_BOOT_CONFIG		(MPUI_BASE + 0x18)
-#define MPUI_DSP_API_CONFIG		(MPUI_BASE + 0x1c)
-
-/*
- * ----------------------------------------------------------------------------
- * LED Pulse Generator
- * ----------------------------------------------------------------------------
- */
-#define OMAP_LPG1_BASE			0xfffbd000
-#define OMAP_LPG2_BASE			0xfffbd800
-#define OMAP_LPG1_LCR			(OMAP_LPG1_BASE + 0x00)
-#define OMAP_LPG1_PMR			(OMAP_LPG1_BASE + 0x04)
-#define OMAP_LPG2_LCR			(OMAP_LPG2_BASE + 0x00)
-#define OMAP_LPG2_PMR			(OMAP_LPG2_BASE + 0x04)
-
-/*
- * ----------------------------------------------------------------------------
- * Pulse-Width Light
- * ----------------------------------------------------------------------------
- */
-#define OMAP_PWL_BASE			0xfffb5800
-#define OMAP_PWL_ENABLE			(OMAP_PWL_BASE + 0x00)
-#define OMAP_PWL_CLK_ENABLE		(OMAP_PWL_BASE + 0x04)
-
-/*
- * ---------------------------------------------------------------------------
- * Processor specific defines
- * ---------------------------------------------------------------------------
- */
-
-#include "omap7xx.h"
-#include "omap1510.h"
-#include "omap16xx.h"
-
-#endif	/* __ASM_ARCH_OMAP_HARDWARE_H */
diff --git a/arch/arm/mach-omap1/include/mach/io.h b/arch/arm/mach-omap1/include/mach/io.h
deleted file mode 100644
index ce4f8005b26f..000000000000
--- a/arch/arm/mach-omap1/include/mach/io.h
+++ /dev/null
@@ -1,45 +0,0 @@
-/*
- * arch/arm/mach-omap1/include/mach/io.h
- *
- * IO definitions for TI OMAP processors and boards
- *
- * Copied from arch/arm/mach-sa1100/include/mach/io.h
- * Copyright (C) 1997-1999 Russell King
- *
- * This program is free software; you can redistribute it and/or modify it
- * under the terms of the GNU General Public License as published by the
- * Free Software Foundation; either version 2 of the License, or (at your
- * option) any later version.
- *
- * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
- * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN
- * NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT, INDIRECT,
- * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
- * NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF
- * USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
- * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
- * THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
- *
- * You should have received a copy of the GNU General Public License along
- * with this program; if not, write to the Free Software Foundation, Inc.,
- * 675 Mass Ave, Cambridge, MA 02139, USA.
- *
- * Modifications:
- *  06-12-1997	RMK	Created.
- *  07-04-1999	RMK	Major cleanup
- */
-
-#ifndef __ASM_ARM_ARCH_IO_H
-#define __ASM_ARM_ARCH_IO_H
-
-#define IO_SPACE_LIMIT 0xffffffff
-
-/*
- * We don't actually have real ISA nor PCI buses, but there is so many
- * drivers out there that might just work if we fake them...
- */
-#define __io(a)		__typesafe_io(a)
-
-#endif
diff --git a/arch/arm/mach-omap1/include/mach/irqs.h b/arch/arm/mach-omap1/include/mach/irqs.h
deleted file mode 100644
index 30bf007700cf..000000000000
--- a/arch/arm/mach-omap1/include/mach/irqs.h
+++ /dev/null
@@ -1,251 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-or-later */
-/*
- *  arch/arm/plat-omap/include/mach/irqs.h
- *
- *  Copyright (C) Greg Lonnon 2001
- *  Updated for OMAP-1610 by Tony Lindgren <tony@atomide.com>
- *
- * Copyright (C) 2009 Texas Instruments
- * Added OMAP4 support - Santosh Shilimkar <santosh.shilimkar@ti.com>
- *
- * NOTE: The interrupt vectors for the OMAP-1509, OMAP-1510, and OMAP-1610
- *	 are different.
- */
-
-#ifndef __ASM_ARCH_OMAP15XX_IRQS_H
-#define __ASM_ARCH_OMAP15XX_IRQS_H
-
-/*
- * IRQ numbers for interrupt handler 1
- *
- * NOTE: See also the OMAP-1510 and 1610 specific IRQ numbers below
- *
- */
-#define INT_CAMERA		(NR_IRQS_LEGACY + 1)
-#define INT_FIQ			(NR_IRQS_LEGACY + 3)
-#define INT_RTDX		(NR_IRQS_LEGACY + 6)
-#define INT_DSP_MMU_ABORT	(NR_IRQS_LEGACY + 7)
-#define INT_HOST		(NR_IRQS_LEGACY + 8)
-#define INT_ABORT		(NR_IRQS_LEGACY + 9)
-#define INT_BRIDGE_PRIV		(NR_IRQS_LEGACY + 13)
-#define INT_GPIO_BANK1		(NR_IRQS_LEGACY + 14)
-#define INT_UART3		(NR_IRQS_LEGACY + 15)
-#define INT_TIMER3		(NR_IRQS_LEGACY + 16)
-#define INT_DMA_CH0_6		(NR_IRQS_LEGACY + 19)
-#define INT_DMA_CH1_7		(NR_IRQS_LEGACY + 20)
-#define INT_DMA_CH2_8		(NR_IRQS_LEGACY + 21)
-#define INT_DMA_CH3		(NR_IRQS_LEGACY + 22)
-#define INT_DMA_CH4		(NR_IRQS_LEGACY + 23)
-#define INT_DMA_CH5		(NR_IRQS_LEGACY + 24)
-#define INT_TIMER1		(NR_IRQS_LEGACY + 26)
-#define INT_WD_TIMER		(NR_IRQS_LEGACY + 27)
-#define INT_BRIDGE_PUB		(NR_IRQS_LEGACY + 28)
-#define INT_TIMER2		(NR_IRQS_LEGACY + 30)
-#define INT_LCD_CTRL		(NR_IRQS_LEGACY + 31)
-
-/*
- * OMAP-1510 specific IRQ numbers for interrupt handler 1
- */
-#define INT_1510_IH2_IRQ	(NR_IRQS_LEGACY + 0)
-#define INT_1510_RES2		(NR_IRQS_LEGACY + 2)
-#define INT_1510_SPI_TX		(NR_IRQS_LEGACY + 4)
-#define INT_1510_SPI_RX		(NR_IRQS_LEGACY + 5)
-#define INT_1510_DSP_MAILBOX1	(NR_IRQS_LEGACY + 10)
-#define INT_1510_DSP_MAILBOX2	(NR_IRQS_LEGACY + 11)
-#define INT_1510_RES12		(NR_IRQS_LEGACY + 12)
-#define INT_1510_LB_MMU		(NR_IRQS_LEGACY + 17)
-#define INT_1510_RES18		(NR_IRQS_LEGACY + 18)
-#define INT_1510_LOCAL_BUS	(NR_IRQS_LEGACY + 29)
-
-/*
- * OMAP-1610 specific IRQ numbers for interrupt handler 1
- */
-#define INT_1610_IH2_IRQ	INT_1510_IH2_IRQ
-#define INT_1610_IH2_FIQ	(NR_IRQS_LEGACY + 2)
-#define INT_1610_McBSP2_TX	(NR_IRQS_LEGACY + 4)
-#define INT_1610_McBSP2_RX	(NR_IRQS_LEGACY + 5)
-#define INT_1610_DSP_MAILBOX1	(NR_IRQS_LEGACY + 10)
-#define INT_1610_DSP_MAILBOX2	(NR_IRQS_LEGACY + 11)
-#define INT_1610_LCD_LINE	(NR_IRQS_LEGACY + 12)
-#define INT_1610_GPTIMER1	(NR_IRQS_LEGACY + 17)
-#define INT_1610_GPTIMER2	(NR_IRQS_LEGACY + 18)
-#define INT_1610_SSR_FIFO_0	(NR_IRQS_LEGACY + 29)
-
-/*
- * OMAP-7xx specific IRQ numbers for interrupt handler 1
- */
-#define INT_7XX_IH2_FIQ		(NR_IRQS_LEGACY + 0)
-#define INT_7XX_IH2_IRQ		(NR_IRQS_LEGACY + 1)
-#define INT_7XX_USB_NON_ISO	(NR_IRQS_LEGACY + 2)
-#define INT_7XX_USB_ISO		(NR_IRQS_LEGACY + 3)
-#define INT_7XX_ICR		(NR_IRQS_LEGACY + 4)
-#define INT_7XX_EAC		(NR_IRQS_LEGACY + 5)
-#define INT_7XX_GPIO_BANK1	(NR_IRQS_LEGACY + 6)
-#define INT_7XX_GPIO_BANK2	(NR_IRQS_LEGACY + 7)
-#define INT_7XX_GPIO_BANK3	(NR_IRQS_LEGACY + 8)
-#define INT_7XX_McBSP2TX	(NR_IRQS_LEGACY + 10)
-#define INT_7XX_McBSP2RX	(NR_IRQS_LEGACY + 11)
-#define INT_7XX_McBSP2RX_OVF	(NR_IRQS_LEGACY + 12)
-#define INT_7XX_LCD_LINE	(NR_IRQS_LEGACY + 14)
-#define INT_7XX_GSM_PROTECT	(NR_IRQS_LEGACY + 15)
-#define INT_7XX_TIMER3		(NR_IRQS_LEGACY + 16)
-#define INT_7XX_GPIO_BANK5	(NR_IRQS_LEGACY + 17)
-#define INT_7XX_GPIO_BANK6	(NR_IRQS_LEGACY + 18)
-#define INT_7XX_SPGIO_WR	(NR_IRQS_LEGACY + 29)
-
-/*
- * IRQ numbers for interrupt handler 2
- *
- * NOTE: See also the OMAP-1510 and 1610 specific IRQ numbers below
- */
-#define IH2_BASE		(NR_IRQS_LEGACY + 32)
-
-#define INT_KEYBOARD		(1 + IH2_BASE)
-#define INT_uWireTX		(2 + IH2_BASE)
-#define INT_uWireRX		(3 + IH2_BASE)
-#define INT_I2C			(4 + IH2_BASE)
-#define INT_MPUIO		(5 + IH2_BASE)
-#define INT_USB_HHC_1		(6 + IH2_BASE)
-#define INT_McBSP3TX		(10 + IH2_BASE)
-#define INT_McBSP3RX		(11 + IH2_BASE)
-#define INT_McBSP1TX		(12 + IH2_BASE)
-#define INT_McBSP1RX		(13 + IH2_BASE)
-#define INT_UART1		(14 + IH2_BASE)
-#define INT_UART2		(15 + IH2_BASE)
-#define INT_BT_MCSI1TX		(16 + IH2_BASE)
-#define INT_BT_MCSI1RX		(17 + IH2_BASE)
-#define INT_SOSSI_MATCH		(19 + IH2_BASE)
-#define INT_USB_W2FC		(20 + IH2_BASE)
-#define INT_1WIRE		(21 + IH2_BASE)
-#define INT_OS_TIMER		(22 + IH2_BASE)
-#define INT_MMC			(23 + IH2_BASE)
-#define INT_GAUGE_32K		(24 + IH2_BASE)
-#define INT_RTC_TIMER		(25 + IH2_BASE)
-#define INT_RTC_ALARM		(26 + IH2_BASE)
-#define INT_MEM_STICK		(27 + IH2_BASE)
-
-/*
- * OMAP-1510 specific IRQ numbers for interrupt handler 2
- */
-#define INT_1510_DSP_MMU	(28 + IH2_BASE)
-#define INT_1510_COM_SPI_RO	(31 + IH2_BASE)
-
-/*
- * OMAP-1610 specific IRQ numbers for interrupt handler 2
- */
-#define INT_1610_FAC		(0 + IH2_BASE)
-#define INT_1610_USB_HHC_2	(7 + IH2_BASE)
-#define INT_1610_USB_OTG	(8 + IH2_BASE)
-#define INT_1610_SoSSI		(9 + IH2_BASE)
-#define INT_1610_SoSSI_MATCH	(19 + IH2_BASE)
-#define INT_1610_DSP_MMU	(28 + IH2_BASE)
-#define INT_1610_McBSP2RX_OF	(31 + IH2_BASE)
-#define INT_1610_STI		(32 + IH2_BASE)
-#define INT_1610_STI_WAKEUP	(33 + IH2_BASE)
-#define INT_1610_GPTIMER3	(34 + IH2_BASE)
-#define INT_1610_GPTIMER4	(35 + IH2_BASE)
-#define INT_1610_GPTIMER5	(36 + IH2_BASE)
-#define INT_1610_GPTIMER6	(37 + IH2_BASE)
-#define INT_1610_GPTIMER7	(38 + IH2_BASE)
-#define INT_1610_GPTIMER8	(39 + IH2_BASE)
-#define INT_1610_GPIO_BANK2	(40 + IH2_BASE)
-#define INT_1610_GPIO_BANK3	(41 + IH2_BASE)
-#define INT_1610_MMC2		(42 + IH2_BASE)
-#define INT_1610_CF		(43 + IH2_BASE)
-#define INT_1610_WAKE_UP_REQ	(46 + IH2_BASE)
-#define INT_1610_GPIO_BANK4	(48 + IH2_BASE)
-#define INT_1610_SPI		(49 + IH2_BASE)
-#define INT_1610_DMA_CH6	(53 + IH2_BASE)
-#define INT_1610_DMA_CH7	(54 + IH2_BASE)
-#define INT_1610_DMA_CH8	(55 + IH2_BASE)
-#define INT_1610_DMA_CH9	(56 + IH2_BASE)
-#define INT_1610_DMA_CH10	(57 + IH2_BASE)
-#define INT_1610_DMA_CH11	(58 + IH2_BASE)
-#define INT_1610_DMA_CH12	(59 + IH2_BASE)
-#define INT_1610_DMA_CH13	(60 + IH2_BASE)
-#define INT_1610_DMA_CH14	(61 + IH2_BASE)
-#define INT_1610_DMA_CH15	(62 + IH2_BASE)
-#define INT_1610_NAND		(63 + IH2_BASE)
-#define INT_1610_SHA1MD5	(91 + IH2_BASE)
-
-/*
- * OMAP-7xx specific IRQ numbers for interrupt handler 2
- */
-#define INT_7XX_HW_ERRORS	(0 + IH2_BASE)
-#define INT_7XX_NFIQ_PWR_FAIL	(1 + IH2_BASE)
-#define INT_7XX_CFCD		(2 + IH2_BASE)
-#define INT_7XX_CFIREQ		(3 + IH2_BASE)
-#define INT_7XX_I2C		(4 + IH2_BASE)
-#define INT_7XX_PCC		(5 + IH2_BASE)
-#define INT_7XX_MPU_EXT_NIRQ	(6 + IH2_BASE)
-#define INT_7XX_SPI_100K_1	(7 + IH2_BASE)
-#define INT_7XX_SYREN_SPI	(8 + IH2_BASE)
-#define INT_7XX_VLYNQ		(9 + IH2_BASE)
-#define INT_7XX_GPIO_BANK4	(10 + IH2_BASE)
-#define INT_7XX_McBSP1TX	(11 + IH2_BASE)
-#define INT_7XX_McBSP1RX	(12 + IH2_BASE)
-#define INT_7XX_McBSP1RX_OF	(13 + IH2_BASE)
-#define INT_7XX_UART_MODEM_IRDA_2 (14 + IH2_BASE)
-#define INT_7XX_UART_MODEM_1	(15 + IH2_BASE)
-#define INT_7XX_MCSI		(16 + IH2_BASE)
-#define INT_7XX_uWireTX		(17 + IH2_BASE)
-#define INT_7XX_uWireRX		(18 + IH2_BASE)
-#define INT_7XX_SMC_CD		(19 + IH2_BASE)
-#define INT_7XX_SMC_IREQ	(20 + IH2_BASE)
-#define INT_7XX_HDQ_1WIRE	(21 + IH2_BASE)
-#define INT_7XX_TIMER32K	(22 + IH2_BASE)
-#define INT_7XX_MMC_SDIO	(23 + IH2_BASE)
-#define INT_7XX_UPLD		(24 + IH2_BASE)
-#define INT_7XX_USB_HHC_1	(27 + IH2_BASE)
-#define INT_7XX_USB_HHC_2	(28 + IH2_BASE)
-#define INT_7XX_USB_GENI	(29 + IH2_BASE)
-#define INT_7XX_USB_OTG		(30 + IH2_BASE)
-#define INT_7XX_CAMERA_IF	(31 + IH2_BASE)
-#define INT_7XX_RNG		(32 + IH2_BASE)
-#define INT_7XX_DUAL_MODE_TIMER (33 + IH2_BASE)
-#define INT_7XX_DBB_RF_EN	(34 + IH2_BASE)
-#define INT_7XX_MPUIO_KEYPAD	(35 + IH2_BASE)
-#define INT_7XX_SHA1_MD5	(36 + IH2_BASE)
-#define INT_7XX_SPI_100K_2	(37 + IH2_BASE)
-#define INT_7XX_RNG_IDLE	(38 + IH2_BASE)
-#define INT_7XX_MPUIO		(39 + IH2_BASE)
-#define INT_7XX_LLPC_LCD_CTRL_CAN_BE_OFF	(40 + IH2_BASE)
-#define INT_7XX_LLPC_OE_FALLING (41 + IH2_BASE)
-#define INT_7XX_LLPC_OE_RISING	(42 + IH2_BASE)
-#define INT_7XX_LLPC_VSYNC	(43 + IH2_BASE)
-#define INT_7XX_WAKE_UP_REQ	(46 + IH2_BASE)
-#define INT_7XX_DMA_CH6		(53 + IH2_BASE)
-#define INT_7XX_DMA_CH7		(54 + IH2_BASE)
-#define INT_7XX_DMA_CH8		(55 + IH2_BASE)
-#define INT_7XX_DMA_CH9		(56 + IH2_BASE)
-#define INT_7XX_DMA_CH10	(57 + IH2_BASE)
-#define INT_7XX_DMA_CH11	(58 + IH2_BASE)
-#define INT_7XX_DMA_CH12	(59 + IH2_BASE)
-#define INT_7XX_DMA_CH13	(60 + IH2_BASE)
-#define INT_7XX_DMA_CH14	(61 + IH2_BASE)
-#define INT_7XX_DMA_CH15	(62 + IH2_BASE)
-#define INT_7XX_NAND		(63 + IH2_BASE)
-
-/* Max. 128 level 2 IRQs (OMAP1610), 192 GPIOs (OMAP730/850) and
- * 16 MPUIO lines */
-#define OMAP_MAX_GPIO_LINES	192
-#define IH_GPIO_BASE		(128 + IH2_BASE)
-#define IH_MPUIO_BASE		(OMAP_MAX_GPIO_LINES + IH_GPIO_BASE)
-#define OMAP_IRQ_END		(IH_MPUIO_BASE + 16)
-
-/* External FPGA handles interrupts on Innovator boards */
-#define	OMAP_FPGA_IRQ_BASE	(OMAP_IRQ_END)
-#ifdef	CONFIG_MACH_OMAP_INNOVATOR
-#define OMAP_FPGA_NR_IRQS	24
-#else
-#define OMAP_FPGA_NR_IRQS	0
-#endif
-#define OMAP_FPGA_IRQ_END	(OMAP_FPGA_IRQ_BASE + OMAP_FPGA_NR_IRQS)
-
-#define OMAP_IRQ_BIT(irq)	(1 << ((irq - NR_IRQS_LEGACY) % 32))
-
-#ifdef CONFIG_FIQ
-#define FIQ_START		1024
-#endif
-
-#endif
diff --git a/arch/arm/mach-omap1/include/mach/lcdc.h b/arch/arm/mach-omap1/include/mach/lcdc.h
deleted file mode 100644
index 7152db1f5361..000000000000
--- a/arch/arm/mach-omap1/include/mach/lcdc.h
+++ /dev/null
@@ -1,44 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-or-later */
-/*
- * arch/arm/mach-omap1/include/mach/lcdc.h
- *
- * Extracted from drivers/video/omap/lcdc.c
- * Copyright (C) 2004 Nokia Corporation
- * Author: Imre Deak <imre.deak@nokia.com>
- */
-#ifndef __MACH_LCDC_H__
-#define __MACH_LCDC_H__
-
-#define OMAP_LCDC_BASE			0xfffec000
-#define OMAP_LCDC_SIZE			256
-#define OMAP_LCDC_IRQ			INT_LCD_CTRL
-
-#define OMAP_LCDC_CONTROL		(OMAP_LCDC_BASE + 0x00)
-#define OMAP_LCDC_TIMING0		(OMAP_LCDC_BASE + 0x04)
-#define OMAP_LCDC_TIMING1		(OMAP_LCDC_BASE + 0x08)
-#define OMAP_LCDC_TIMING2		(OMAP_LCDC_BASE + 0x0c)
-#define OMAP_LCDC_STATUS		(OMAP_LCDC_BASE + 0x10)
-#define OMAP_LCDC_SUBPANEL		(OMAP_LCDC_BASE + 0x14)
-#define OMAP_LCDC_LINE_INT		(OMAP_LCDC_BASE + 0x18)
-#define OMAP_LCDC_DISPLAY_STATUS	(OMAP_LCDC_BASE + 0x1c)
-
-#define OMAP_LCDC_STAT_DONE		(1 << 0)
-#define OMAP_LCDC_STAT_VSYNC		(1 << 1)
-#define OMAP_LCDC_STAT_SYNC_LOST	(1 << 2)
-#define OMAP_LCDC_STAT_ABC		(1 << 3)
-#define OMAP_LCDC_STAT_LINE_INT		(1 << 4)
-#define OMAP_LCDC_STAT_FUF		(1 << 5)
-#define OMAP_LCDC_STAT_LOADED_PALETTE	(1 << 6)
-
-#define OMAP_LCDC_CTRL_LCD_EN		(1 << 0)
-#define OMAP_LCDC_CTRL_LCD_TFT		(1 << 7)
-#define OMAP_LCDC_CTRL_LINE_IRQ_CLR_SEL	(1 << 10)
-
-#define OMAP_LCDC_IRQ_VSYNC		(1 << 2)
-#define OMAP_LCDC_IRQ_DONE		(1 << 3)
-#define OMAP_LCDC_IRQ_LOADED_PALETTE	(1 << 4)
-#define OMAP_LCDC_IRQ_LINE_NIRQ		(1 << 5)
-#define OMAP_LCDC_IRQ_LINE		(1 << 6)
-#define OMAP_LCDC_IRQ_MASK		(((1 << 5) - 1) << 2)
-
-#endif /* __MACH_LCDC_H__ */
diff --git a/arch/arm/mach-omap1/include/mach/memory.h b/arch/arm/mach-omap1/include/mach/memory.h
deleted file mode 100644
index ba3a350479c8..000000000000
--- a/arch/arm/mach-omap1/include/mach/memory.h
+++ /dev/null
@@ -1,12 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-/*
- * arch/arm/mach-omap1/include/mach/memory.h
- */
-
-#ifndef __ASM_ARCH_MEMORY_H
-#define __ASM_ARCH_MEMORY_H
-
-/* REVISIT: omap1 legacy drivers still rely on this */
-#include <mach/soc.h>
-
-#endif
diff --git a/arch/arm/mach-omap1/include/mach/mtd-xip.h b/arch/arm/mach-omap1/include/mach/mtd-xip.h
deleted file mode 100644
index d09b2bc4920f..000000000000
--- a/arch/arm/mach-omap1/include/mach/mtd-xip.h
+++ /dev/null
@@ -1,61 +0,0 @@
-/*
- * MTD primitives for XIP support. Architecture specific functions.
- *
- * Do not include this file directly. It's included from linux/mtd/xip.h
- *
- * Author: Vladimir Barinov <vbarinov@embeddedalley.com>
- *
- * (c) 2005 MontaVista Software, Inc.  This file is licensed under the
- * terms of the GNU General Public License version 2.  This program is
- * licensed "as is" without any warranty of any kind, whether express or
- * implied.
- */
-
-#ifndef __ARCH_OMAP_MTD_XIP_H__
-#define __ARCH_OMAP_MTD_XIP_H__
-
-#include <mach/hardware.h>
-#define OMAP_MPU_TIMER_BASE	(0xfffec500)
-#define OMAP_MPU_TIMER_OFFSET	0x100
-
-typedef struct {
-	u32 cntl;			/* CNTL_TIMER, R/W */
-	u32 load_tim;			/* LOAD_TIM,   W */
-	u32 read_tim;			/* READ_TIM,   R */
-} xip_omap_mpu_timer_regs_t;
-
-#define xip_omap_mpu_timer_base(n)					\
-((volatile xip_omap_mpu_timer_regs_t*)OMAP1_IO_ADDRESS(OMAP_MPU_TIMER_BASE +	\
-	(n)*OMAP_MPU_TIMER_OFFSET))
-
-static inline unsigned long xip_omap_mpu_timer_read(int nr)
-{
-	volatile xip_omap_mpu_timer_regs_t* timer = xip_omap_mpu_timer_base(nr);
-	return timer->read_tim;
-}
-
-#define xip_irqpending()	\
-	(omap_readl(OMAP_IH1_ITR) & ~omap_readl(OMAP_IH1_MIR))
-#define xip_currtime()		(~xip_omap_mpu_timer_read(0))
-
-/*
- * It's permitted to do approximation for xip_elapsed_since macro
- * (see linux/mtd/xip.h)
- */
-
-#ifdef CONFIG_MACH_OMAP_PERSEUS2
-#define xip_elapsed_since(x)	(signed)((~xip_omap_mpu_timer_read(0) - (x)) / 7)
-#else
-#define xip_elapsed_since(x)	(signed)((~xip_omap_mpu_timer_read(0) - (x)) / 6)
-#endif
-
-/*
- * xip_cpu_idle() is used when waiting for a delay equal or larger than
- * the system timer tick period.  This should put the CPU into idle mode
- * to save power and to be woken up only when some interrupts are pending.
- * As above, this should not rely upon standard kernel code.
- */
-
-#define xip_cpu_idle()  asm volatile ("mcr p15, 0, %0, c7, c0, 4" :: "r" (1))
-
-#endif /* __ARCH_OMAP_MTD_XIP_H__ */
diff --git a/arch/arm/mach-omap1/include/mach/mux.h b/arch/arm/mach-omap1/include/mach/mux.h
deleted file mode 100644
index 3f6dc55d9898..000000000000
--- a/arch/arm/mach-omap1/include/mach/mux.h
+++ /dev/null
@@ -1,441 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-or-later */
-/*
- * arch/arm/plat-omap/include/mach/mux.h
- *
- * Table of the Omap register configurations for the FUNC_MUX and
- * PULL_DWN combinations.
- *
- * Copyright (C) 2004 - 2008 Texas Instruments Inc.
- * Copyright (C) 2003 - 2008 Nokia Corporation
- *
- * Written by Tony Lindgren
- *
- * NOTE: Please use the following naming style for new pin entries.
- *	 For example, W8_1610_MMC2_DAT0, where:
- *	 - W8	     = ball
- *	 - 1610	     = 1510 or 1610, none if common for both 1510 and 1610
- *	 - MMC2_DAT0 = function
- */
-
-#ifndef __ASM_ARCH_MUX_H
-#define __ASM_ARCH_MUX_H
-
-#define PU_PD_SEL_NA		0	/* No pu_pd reg available */
-#define PULL_DWN_CTRL_NA	0	/* No pull-down control needed */
-
-#ifdef	CONFIG_OMAP_MUX_DEBUG
-#define MUX_REG(reg, mode_offset, mode) .mux_reg_name = "FUNC_MUX_CTRL_"#reg, \
-					.mux_reg = FUNC_MUX_CTRL_##reg, \
-					.mask_offset = mode_offset, \
-					.mask = mode,
-
-#define PULL_REG(reg, bit, status)	.pull_name = "PULL_DWN_CTRL_"#reg, \
-					.pull_reg = PULL_DWN_CTRL_##reg, \
-					.pull_bit = bit, \
-					.pull_val = status,
-
-#define PU_PD_REG(reg, status)		.pu_pd_name = "PU_PD_SEL_"#reg, \
-					.pu_pd_reg = PU_PD_SEL_##reg, \
-					.pu_pd_val = status,
-
-#define MUX_REG_7XX(reg, mode_offset, mode) .mux_reg_name = "OMAP7XX_IO_CONF_"#reg, \
-					.mux_reg = OMAP7XX_IO_CONF_##reg, \
-					.mask_offset = mode_offset, \
-					.mask = mode,
-
-#define PULL_REG_7XX(reg, bit, status)	.pull_name = "OMAP7XX_IO_CONF_"#reg, \
-					.pull_reg = OMAP7XX_IO_CONF_##reg, \
-					.pull_bit = bit, \
-					.pull_val = status,
-
-#else
-
-#define MUX_REG(reg, mode_offset, mode) .mux_reg = FUNC_MUX_CTRL_##reg, \
-					.mask_offset = mode_offset, \
-					.mask = mode,
-
-#define PULL_REG(reg, bit, status)	.pull_reg = PULL_DWN_CTRL_##reg, \
-					.pull_bit = bit, \
-					.pull_val = status,
-
-#define PU_PD_REG(reg, status)		.pu_pd_reg = PU_PD_SEL_##reg, \
-					.pu_pd_val = status,
-
-#define MUX_REG_7XX(reg, mode_offset, mode) \
-					.mux_reg = OMAP7XX_IO_CONF_##reg, \
-					.mask_offset = mode_offset, \
-					.mask = mode,
-
-#define PULL_REG_7XX(reg, bit, status)	.pull_reg = OMAP7XX_IO_CONF_##reg, \
-					.pull_bit = bit, \
-					.pull_val = status,
-
-#endif /* CONFIG_OMAP_MUX_DEBUG */
-
-#define MUX_CFG(desc, mux_reg, mode_offset, mode,	\
-		pull_reg, pull_bit, pull_status,	\
-		pu_pd_reg, pu_pd_status, debug_status)	\
-{							\
-	.name =	 desc,					\
-	.debug = debug_status,				\
-	MUX_REG(mux_reg, mode_offset, mode)		\
-	PULL_REG(pull_reg, pull_bit, pull_status)	\
-	PU_PD_REG(pu_pd_reg, pu_pd_status)		\
-},
-
-
-/*
- * OMAP730/850 has a slightly different config for the pin mux.
- * - config regs are the OMAP7XX_IO_CONF_x regs (see omap7xx.h) regs and
- *   not the FUNC_MUX_CTRL_x regs from hardware.h
- * - for pull-up/down, only has one enable bit which is in the same register
- *   as mux config
- */
-#define MUX_CFG_7XX(desc, mux_reg, mode_offset, mode,	\
-		   pull_bit, pull_status, debug_status)\
-{							\
-	.name =	 desc,					\
-	.debug = debug_status,				\
-	MUX_REG_7XX(mux_reg, mode_offset, mode)		\
-	PULL_REG_7XX(mux_reg, pull_bit, pull_status)	\
-	PU_PD_REG(NA, 0)		\
-},
-
-struct pin_config {
-	char 			*name;
-	const unsigned int 	mux_reg;
-	unsigned char		debug;
-
-	const unsigned char mask_offset;
-	const unsigned char mask;
-
-	const char *pull_name;
-	const unsigned int pull_reg;
-	const unsigned char pull_val;
-	const unsigned char pull_bit;
-
-	const char *pu_pd_name;
-	const unsigned int pu_pd_reg;
-	const unsigned char pu_pd_val;
-
-#if	defined(CONFIG_OMAP_MUX_DEBUG) || defined(CONFIG_OMAP_MUX_WARNINGS)
-	const char *mux_reg_name;
-#endif
-
-};
-
-enum omap7xx_index {
-	/* OMAP 730 keyboard */
-	E2_7XX_KBR0,
-	J7_7XX_KBR1,
-	E1_7XX_KBR2,
-	F3_7XX_KBR3,
-	D2_7XX_KBR4,
-	C2_7XX_KBC0,
-	D3_7XX_KBC1,
-	E4_7XX_KBC2,
-	F4_7XX_KBC3,
-	E3_7XX_KBC4,
-
-	/* USB */
-	AA17_7XX_USB_DM,
-	W16_7XX_USB_PU_EN,
-	W17_7XX_USB_VBUSI,
-	W18_7XX_USB_DMCK_OUT,
-	W19_7XX_USB_DCRST,
-
-	/* MMC */
-	MMC_7XX_CMD,
-	MMC_7XX_CLK,
-	MMC_7XX_DAT0,
-
-	/* I2C */
-	I2C_7XX_SCL,
-	I2C_7XX_SDA,
-
-	/* SPI */
-	SPI_7XX_1,
-	SPI_7XX_2,
-	SPI_7XX_3,
-	SPI_7XX_4,
-	SPI_7XX_5,
-	SPI_7XX_6,
-
-	/* UART */
-	UART_7XX_1,
-	UART_7XX_2,
-};
-
-enum omap1xxx_index {
-	/* UART1 (BT_UART_GATING)*/
-	UART1_TX = 0,
-	UART1_RTS,
-
-	/* UART2 (COM_UART_GATING)*/
-	UART2_TX,
-	UART2_RX,
-	UART2_CTS,
-	UART2_RTS,
-
-	/* UART3 (GIGA_UART_GATING) */
-	UART3_TX,
-	UART3_RX,
-	UART3_CTS,
-	UART3_RTS,
-	UART3_CLKREQ,
-	UART3_BCLK,	/* 12MHz clock out */
-	Y15_1610_UART3_RTS,
-
-	/* PWT & PWL */
-	PWT,
-	PWL,
-
-	/* USB master generic */
-	R18_USB_VBUS,
-	R18_1510_USB_GPIO0,
-	W4_USB_PUEN,
-	W4_USB_CLKO,
-	W4_USB_HIGHZ,
-	W4_GPIO58,
-
-	/* USB1 master */
-	USB1_SUSP,
-	USB1_SEO,
-	W13_1610_USB1_SE0,
-	USB1_TXEN,
-	USB1_TXD,
-	USB1_VP,
-	USB1_VM,
-	USB1_RCV,
-	USB1_SPEED,
-	R13_1610_USB1_SPEED,
-	R13_1710_USB1_SE0,
-
-	/* USB2 master */
-	USB2_SUSP,
-	USB2_VP,
-	USB2_TXEN,
-	USB2_VM,
-	USB2_RCV,
-	USB2_SEO,
-	USB2_TXD,
-
-	/* OMAP-1510 GPIO */
-	R18_1510_GPIO0,
-	R19_1510_GPIO1,
-	M14_1510_GPIO2,
-
-	/* OMAP1610 GPIO */
-	P18_1610_GPIO3,
-	Y15_1610_GPIO17,
-
-	/* OMAP-1710 GPIO */
-	R18_1710_GPIO0,
-	V2_1710_GPIO10,
-	N21_1710_GPIO14,
-	W15_1710_GPIO40,
-
-	/* MPUIO */
-	MPUIO2,
-	N15_1610_MPUIO2,
-	MPUIO4,
-	MPUIO5,
-	T20_1610_MPUIO5,
-	W11_1610_MPUIO6,
-	V10_1610_MPUIO7,
-	W11_1610_MPUIO9,
-	V10_1610_MPUIO10,
-	W10_1610_MPUIO11,
-	E20_1610_MPUIO13,
-	U20_1610_MPUIO14,
-	E19_1610_MPUIO15,
-
-	/* MCBSP2 */
-	MCBSP2_CLKR,
-	MCBSP2_CLKX,
-	MCBSP2_DR,
-	MCBSP2_DX,
-	MCBSP2_FSR,
-	MCBSP2_FSX,
-
-	/* MCBSP3 */
-	MCBSP3_CLKX,
-
-	/* Misc ballouts */
-	BALLOUT_V8_ARMIO3,
-	N20_HDQ,
-
-	/* OMAP-1610 MMC2 */
-	W8_1610_MMC2_DAT0,
-	V8_1610_MMC2_DAT1,
-	W15_1610_MMC2_DAT2,
-	R10_1610_MMC2_DAT3,
-	Y10_1610_MMC2_CLK,
-	Y8_1610_MMC2_CMD,
-	V9_1610_MMC2_CMDDIR,
-	V5_1610_MMC2_DATDIR0,
-	W19_1610_MMC2_DATDIR1,
-	R18_1610_MMC2_CLKIN,
-
-	/* OMAP-1610 External Trace Interface */
-	M19_1610_ETM_PSTAT0,
-	L15_1610_ETM_PSTAT1,
-	L18_1610_ETM_PSTAT2,
-	L19_1610_ETM_D0,
-	J19_1610_ETM_D6,
-	J18_1610_ETM_D7,
-
-	/* OMAP16XX GPIO */
-	P20_1610_GPIO4,
-	V9_1610_GPIO7,
-	W8_1610_GPIO9,
-	N20_1610_GPIO11,
-	N19_1610_GPIO13,
-	P10_1610_GPIO22,
-	V5_1610_GPIO24,
-	AA20_1610_GPIO_41,
-	W19_1610_GPIO48,
-	M7_1610_GPIO62,
-	V14_16XX_GPIO37,
-	R9_16XX_GPIO18,
-	L14_16XX_GPIO49,
-
-	/* OMAP-1610 uWire */
-	V19_1610_UWIRE_SCLK,
-	U18_1610_UWIRE_SDI,
-	W21_1610_UWIRE_SDO,
-	N14_1610_UWIRE_CS0,
-	P15_1610_UWIRE_CS3,
-	N15_1610_UWIRE_CS1,
-
-	/* OMAP-1610 SPI */
-	U19_1610_SPIF_SCK,
-	U18_1610_SPIF_DIN,
-	P20_1610_SPIF_DIN,
-	W21_1610_SPIF_DOUT,
-	R18_1610_SPIF_DOUT,
-	N14_1610_SPIF_CS0,
-	N15_1610_SPIF_CS1,
-	T19_1610_SPIF_CS2,
-	P15_1610_SPIF_CS3,
-
-	/* OMAP-1610 Flash */
-	L3_1610_FLASH_CS2B_OE,
-	M8_1610_FLASH_CS2B_WE,
-
-	/* First MMC */
-	MMC_CMD,
-	MMC_DAT1,
-	MMC_DAT2,
-	MMC_DAT0,
-	MMC_CLK,
-	MMC_DAT3,
-
-	/* OMAP-1710 MMC CMDDIR and DATDIR0 */
-	M15_1710_MMC_CLKI,
-	P19_1710_MMC_CMDDIR,
-	P20_1710_MMC_DATDIR0,
-
-	/* OMAP-1610 USB0 alternate pin configuration */
-	W9_USB0_TXEN,
-	AA9_USB0_VP,
-	Y5_USB0_RCV,
-	R9_USB0_VM,
-	V6_USB0_TXD,
-	W5_USB0_SE0,
-	V9_USB0_SPEED,
-	V9_USB0_SUSP,
-
-	/* USB2 */
-	W9_USB2_TXEN,
-	AA9_USB2_VP,
-	Y5_USB2_RCV,
-	R9_USB2_VM,
-	V6_USB2_TXD,
-	W5_USB2_SE0,
-
-	/* 16XX UART */
-	R13_1610_UART1_TX,
-	V14_16XX_UART1_RX,
-	R14_1610_UART1_CTS,
-	AA15_1610_UART1_RTS,
-	R9_16XX_UART2_RX,
-	L14_16XX_UART3_RX,
-
-	/* I2C OMAP-1610 */
-	I2C_SCL,
-	I2C_SDA,
-
-	/* Keypad */
-	F18_1610_KBC0,
-	D20_1610_KBC1,
-	D19_1610_KBC2,
-	E18_1610_KBC3,
-	C21_1610_KBC4,
-	G18_1610_KBR0,
-	F19_1610_KBR1,
-	H14_1610_KBR2,
-	E20_1610_KBR3,
-	E19_1610_KBR4,
-	N19_1610_KBR5,
-
-	/* Power management */
-	T20_1610_LOW_PWR,
-
-	/* MCLK Settings */
-	V5_1710_MCLK_ON,
-	V5_1710_MCLK_OFF,
-	R10_1610_MCLK_ON,
-	R10_1610_MCLK_OFF,
-
-	/* CompactFlash controller */
-	P11_1610_CF_CD2,
-	R11_1610_CF_IOIS16,
-	V10_1610_CF_IREQ,
-	W10_1610_CF_RESET,
-	W11_1610_CF_CD1,
-
-	/* parallel camera */
-	J15_1610_CAM_LCLK,
-	J18_1610_CAM_D7,
-	J19_1610_CAM_D6,
-	J14_1610_CAM_D5,
-	K18_1610_CAM_D4,
-	K19_1610_CAM_D3,
-	K15_1610_CAM_D2,
-	K14_1610_CAM_D1,
-	L19_1610_CAM_D0,
-	L18_1610_CAM_VS,
-	L15_1610_CAM_HS,
-	M19_1610_CAM_RSTZ,
-	Y15_1610_CAM_OUTCLK,
-
-	/* serial camera */
-	H19_1610_CAM_EXCLK,
-	Y12_1610_CCP_CLKP,
-	W13_1610_CCP_CLKM,
-	W14_1610_CCP_DATAP,
-	Y14_1610_CCP_DATAM,
-
-};
-
-struct omap_mux_cfg {
-	struct pin_config	*pins;
-	unsigned long		size;
-	int			(*cfg_reg)(const struct pin_config *cfg);
-};
-
-#ifdef	CONFIG_OMAP_MUX
-/* setup pin muxing in Linux */
-extern int omap1_mux_init(void);
-extern int omap_mux_register(struct omap_mux_cfg *);
-extern int omap_cfg_reg(unsigned long reg_cfg);
-#else
-/* boot loader does it all (no warnings from CONFIG_OMAP_MUX_WARNINGS) */
-static inline int omap1_mux_init(void) { return 0; }
-static inline int omap_cfg_reg(unsigned long reg_cfg) { return 0; }
-#endif
-
-extern int omap2_mux_init(void);
-
-#endif
diff --git a/arch/arm/mach-omap1/include/mach/soc.h b/arch/arm/mach-omap1/include/mach/soc.h
deleted file mode 100644
index 1897cbabfc93..000000000000
--- a/arch/arm/mach-omap1/include/mach/soc.h
+++ /dev/null
@@ -1,220 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-or-later */
-/*
- * OMAP cpu type detection
- *
- * Copyright (C) 2004, 2008 Nokia Corporation
- *
- * Copyright (C) 2009-11 Texas Instruments.
- *
- * Written by Tony Lindgren <tony.lindgren@nokia.com>
- *
- * Added OMAP4/5 specific defines - Santosh Shilimkar<santosh.shilimkar@ti.com>
- */
-
-#ifndef __ASM_ARCH_OMAP_CPU_H
-#define __ASM_ARCH_OMAP_CPU_H
-
-#include <asm/irq.h>
-#include <mach/hardware.h>
-#include <mach/irqs.h>
-
-#ifndef __ASSEMBLY__
-
-#include <linux/bitops.h>
-
-/*
- * Test if multicore OMAP support is needed
- */
-#undef MULTI_OMAP1
-#undef OMAP_NAME
-
-#ifdef CONFIG_ARCH_OMAP730
-# ifdef OMAP_NAME
-#  undef  MULTI_OMAP1
-#  define MULTI_OMAP1
-# else
-#  define OMAP_NAME omap730
-# endif
-#endif
-#ifdef CONFIG_ARCH_OMAP850
-# ifdef OMAP_NAME
-#  undef  MULTI_OMAP1
-#  define MULTI_OMAP1
-# else
-#  define OMAP_NAME omap850
-# endif
-#endif
-#ifdef CONFIG_ARCH_OMAP15XX
-# ifdef OMAP_NAME
-#  undef  MULTI_OMAP1
-#  define MULTI_OMAP1
-# else
-#  define OMAP_NAME omap1510
-# endif
-#endif
-#ifdef CONFIG_ARCH_OMAP16XX
-# ifdef OMAP_NAME
-#  undef  MULTI_OMAP1
-#  define MULTI_OMAP1
-# else
-#  define OMAP_NAME omap16xx
-# endif
-#endif
-
-/*
- * omap_rev bits:
- * CPU id bits	(0730, 1510, 1710, 2422...)	[31:16]
- * CPU revision	(See _REV_ defined in cpu.h)	[15:08]
- * CPU class bits (15xx, 16xx, 24xx, 34xx...)	[07:00]
- */
-unsigned int omap_rev(void);
-
-/*
- * Get the CPU revision for OMAP devices
- */
-#define GET_OMAP_REVISION()	((omap_rev() >> 8) & 0xff)
-
-/*
- * Macros to group OMAP into cpu classes.
- * These can be used in most places.
- * cpu_is_omap7xx():	True for OMAP730, OMAP850
- * cpu_is_omap15xx():	True for OMAP1510, OMAP5910 and OMAP310
- * cpu_is_omap16xx():	True for OMAP1610, OMAP5912 and OMAP1710
- */
-#define GET_OMAP_CLASS	(omap_rev() & 0xff)
-
-#define IS_OMAP_CLASS(class, id)			\
-static inline int is_omap ##class (void)		\
-{							\
-	return (GET_OMAP_CLASS == (id)) ? 1 : 0;	\
-}
-
-#define GET_OMAP_SUBCLASS	((omap_rev() >> 20) & 0x0fff)
-
-#define IS_OMAP_SUBCLASS(subclass, id)			\
-static inline int is_omap ##subclass (void)		\
-{							\
-	return (GET_OMAP_SUBCLASS == (id)) ? 1 : 0;	\
-}
-
-IS_OMAP_CLASS(7xx, 0x07)
-IS_OMAP_CLASS(15xx, 0x15)
-IS_OMAP_CLASS(16xx, 0x16)
-
-#define cpu_is_omap7xx()		0
-#define cpu_is_omap15xx()		0
-#define cpu_is_omap16xx()		0
-
-#if defined(MULTI_OMAP1)
-# if defined(CONFIG_ARCH_OMAP730)
-#  undef  cpu_is_omap7xx
-#  define cpu_is_omap7xx()		is_omap7xx()
-# endif
-# if defined(CONFIG_ARCH_OMAP850)
-#  undef  cpu_is_omap7xx
-#  define cpu_is_omap7xx()		is_omap7xx()
-# endif
-# if defined(CONFIG_ARCH_OMAP15XX)
-#  undef  cpu_is_omap15xx
-#  define cpu_is_omap15xx()		is_omap15xx()
-# endif
-# if defined(CONFIG_ARCH_OMAP16XX)
-#  undef  cpu_is_omap16xx
-#  define cpu_is_omap16xx()		is_omap16xx()
-# endif
-#else
-# if defined(CONFIG_ARCH_OMAP730)
-#  undef  cpu_is_omap7xx
-#  define cpu_is_omap7xx()		1
-# endif
-# if defined(CONFIG_ARCH_OMAP850)
-#  undef  cpu_is_omap7xx
-#  define cpu_is_omap7xx()		1
-# endif
-# if defined(CONFIG_ARCH_OMAP15XX)
-#  undef  cpu_is_omap15xx
-#  define cpu_is_omap15xx()		1
-# endif
-# if defined(CONFIG_ARCH_OMAP16XX)
-#  undef  cpu_is_omap16xx
-#  define cpu_is_omap16xx()		1
-# endif
-#endif
-
-/*
- * Macros to detect individual cpu types.
- * These are only rarely needed.
- * cpu_is_omap310():	True for OMAP310
- * cpu_is_omap1510():	True for OMAP1510
- * cpu_is_omap1610():	True for OMAP1610
- * cpu_is_omap1611():	True for OMAP1611
- * cpu_is_omap5912():	True for OMAP5912
- * cpu_is_omap1621():	True for OMAP1621
- * cpu_is_omap1710():	True for OMAP1710
- */
-#define GET_OMAP_TYPE	((omap_rev() >> 16) & 0xffff)
-
-#define IS_OMAP_TYPE(type, id)				\
-static inline int is_omap ##type (void)			\
-{							\
-	return (GET_OMAP_TYPE == (id)) ? 1 : 0;		\
-}
-
-IS_OMAP_TYPE(310, 0x0310)
-IS_OMAP_TYPE(1510, 0x1510)
-IS_OMAP_TYPE(1610, 0x1610)
-IS_OMAP_TYPE(1611, 0x1611)
-IS_OMAP_TYPE(5912, 0x1611)
-IS_OMAP_TYPE(1621, 0x1621)
-IS_OMAP_TYPE(1710, 0x1710)
-
-#define cpu_is_omap310()		0
-#define cpu_is_omap1510()		0
-#define cpu_is_omap1610()		0
-#define cpu_is_omap5912()		0
-#define cpu_is_omap1611()		0
-#define cpu_is_omap1621()		0
-#define cpu_is_omap1710()		0
-
-/* These are needed to compile common code */
-#ifdef CONFIG_ARCH_OMAP1
-#define cpu_is_omap242x()		0
-#define cpu_is_omap2430()		0
-#define cpu_is_omap243x()		0
-#define cpu_is_omap24xx()		0
-#define cpu_is_omap34xx()		0
-#define cpu_is_omap44xx()		0
-#define soc_is_omap54xx()		0
-#define soc_is_dra7xx()			0
-#define soc_is_am33xx()			0
-#define cpu_class_is_omap1()		1
-#define cpu_class_is_omap2()		0
-#endif
-
-/*
- * Whether we have MULTI_OMAP1 or not, we still need to distinguish
- * between 310 vs. 1510 and 1611B/5912 vs. 1710.
- */
-
-#if defined(CONFIG_ARCH_OMAP15XX)
-# undef  cpu_is_omap310
-# undef  cpu_is_omap1510
-# define cpu_is_omap310()		is_omap310()
-# define cpu_is_omap1510()		is_omap1510()
-#endif
-
-#if defined(CONFIG_ARCH_OMAP16XX)
-# undef  cpu_is_omap1610
-# undef  cpu_is_omap1611
-# undef  cpu_is_omap5912
-# undef  cpu_is_omap1621
-# undef  cpu_is_omap1710
-# define cpu_is_omap1610()		is_omap1610()
-# define cpu_is_omap1611()		is_omap1611()
-# define cpu_is_omap5912()		is_omap5912()
-# define cpu_is_omap1621()		is_omap1621()
-# define cpu_is_omap1710()		is_omap1710()
-#endif
-
-#endif	/* __ASSEMBLY__ */
-#endif
diff --git a/arch/arm/mach-omap1/include/mach/tc.h b/arch/arm/mach-omap1/include/mach/tc.h
deleted file mode 100644
index adaab6a0bd08..000000000000
--- a/arch/arm/mach-omap1/include/mach/tc.h
+++ /dev/null
@@ -1,76 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-or-later */
-/*
- * arch/arm/plat-omap/include/mach/tc.h
- *
- * OMAP Traffic Controller
- *
- * Copyright (C) 2004 Nokia Corporation
- * Author: Imre Deak <imre.deak@nokia.com>
- */
-
-#ifndef __ASM_ARCH_TC_H
-#define __ASM_ARCH_TC_H
-
-#define TCMIF_BASE		0xfffecc00
-#define OMAP_TC_OCPT1_PRIOR	(TCMIF_BASE + 0x00)
-#define OMAP_TC_EMIFS_PRIOR	(TCMIF_BASE + 0x04)
-#define OMAP_TC_EMIFF_PRIOR	(TCMIF_BASE + 0x08)
-#define EMIFS_CONFIG		(TCMIF_BASE + 0x0c)
-#define EMIFS_CS0_CONFIG	(TCMIF_BASE + 0x10)
-#define EMIFS_CS1_CONFIG	(TCMIF_BASE + 0x14)
-#define EMIFS_CS2_CONFIG	(TCMIF_BASE + 0x18)
-#define EMIFS_CS3_CONFIG	(TCMIF_BASE + 0x1c)
-#define EMIFF_SDRAM_CONFIG	(TCMIF_BASE + 0x20)
-#define EMIFF_MRS		(TCMIF_BASE + 0x24)
-#define TC_TIMEOUT1		(TCMIF_BASE + 0x28)
-#define TC_TIMEOUT2		(TCMIF_BASE + 0x2c)
-#define TC_TIMEOUT3		(TCMIF_BASE + 0x30)
-#define TC_ENDIANISM		(TCMIF_BASE + 0x34)
-#define EMIFF_SDRAM_CONFIG_2	(TCMIF_BASE + 0x3c)
-#define EMIF_CFG_DYNAMIC_WS	(TCMIF_BASE + 0x40)
-#define EMIFS_ACS0		(TCMIF_BASE + 0x50)
-#define EMIFS_ACS1		(TCMIF_BASE + 0x54)
-#define EMIFS_ACS2		(TCMIF_BASE + 0x58)
-#define EMIFS_ACS3		(TCMIF_BASE + 0x5c)
-#define OMAP_TC_OCPT2_PRIOR	(TCMIF_BASE + 0xd0)
-
-/* external EMIFS chipselect regions */
-#define	OMAP_CS0_PHYS		0x00000000
-#define	OMAP_CS0_SIZE		SZ_64M
-
-#define	OMAP_CS1_PHYS		0x04000000
-#define	OMAP_CS1_SIZE		SZ_64M
-
-#define	OMAP_CS1A_PHYS		OMAP_CS1_PHYS
-#define	OMAP_CS1A_SIZE		SZ_32M
-
-#define	OMAP_CS1B_PHYS		(OMAP_CS1A_PHYS + OMAP_CS1A_SIZE)
-#define	OMAP_CS1B_SIZE		SZ_32M
-
-#define	OMAP_CS2_PHYS		0x08000000
-#define	OMAP_CS2_SIZE		SZ_64M
-
-#define	OMAP_CS2A_PHYS		OMAP_CS2_PHYS
-#define	OMAP_CS2A_SIZE		SZ_32M
-
-#define	OMAP_CS2B_PHYS		(OMAP_CS2A_PHYS + OMAP_CS2A_SIZE)
-#define	OMAP_CS2B_SIZE		SZ_32M
-
-#define	OMAP_CS3_PHYS		0x0c000000
-#define	OMAP_CS3_SIZE		SZ_64M
-
-#ifndef	__ASSEMBLER__
-
-/* EMIF Slow Interface Configuration Register */
-#define OMAP_EMIFS_CONFIG_FR		(1 << 4)
-#define OMAP_EMIFS_CONFIG_PDE		(1 << 3)
-#define OMAP_EMIFS_CONFIG_PWD_EN	(1 << 2)
-#define OMAP_EMIFS_CONFIG_BM		(1 << 1)
-#define OMAP_EMIFS_CONFIG_WP		(1 << 0)
-
-#define EMIFS_CCS(n)		(EMIFS_CS0_CONFIG + (4 * (n)))
-#define EMIFS_ACS(n)		(EMIFS_ACS0 + (4 * (n)))
-
-#endif	/* __ASSEMBLER__ */
-
-#endif	/* __ASM_ARCH_TC_H */
diff --git a/arch/arm/mach-omap1/include/mach/uncompress.h b/arch/arm/mach-omap1/include/mach/uncompress.h
deleted file mode 100644
index 9cca6a56788f..000000000000
--- a/arch/arm/mach-omap1/include/mach/uncompress.h
+++ /dev/null
@@ -1,117 +0,0 @@
-/*
- * arch/arm/plat-omap/include/mach/uncompress.h
- *
- * Serial port stubs for kernel decompress status messages
- *
- * Initially based on:
- * linux-2.4.15-rmk1-dsplinux1.6/arch/arm/plat-omap/include/mach1510/uncompress.h
- * Copyright (C) 2000 RidgeRun, Inc.
- * Author: Greg Lonnon <glonnon@ridgerun.com>
- *
- * Rewritten by:
- * Author: <source@mvista.com>
- * 2004 (c) MontaVista Software, Inc.
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2. This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
- */
-
-#include <linux/types.h>
-#include <linux/serial_reg.h>
-
-#include <asm/memory.h>
-#include <asm/mach-types.h>
-
-#include "serial.h"
-
-#define MDR1_MODE_MASK			0x07
-
-volatile u8 *uart_base;
-int uart_shift;
-
-/*
- * Store the DEBUG_LL uart number into memory.
- * See also debug-macro.S, and serial.c for related code.
- */
-static void set_omap_uart_info(unsigned char port)
-{
-	/*
-	 * Get address of some.bss variable and round it down
-	 * a la CONFIG_AUTO_ZRELADDR.
-	 */
-	u32 ram_start = (u32)&uart_shift & 0xf8000000;
-	u32 *uart_info = (u32 *)(ram_start + OMAP_UART_INFO_OFS);
-	*uart_info = port;
-}
-
-static inline void putc(int c)
-{
-	if (!uart_base)
-		return;
-
-	/* Check for UART 16x mode */
-	if ((uart_base[UART_OMAP_MDR1 << uart_shift] & MDR1_MODE_MASK) != 0)
-		return;
-
-	while (!(uart_base[UART_LSR << uart_shift] & UART_LSR_THRE))
-		barrier();
-	uart_base[UART_TX << uart_shift] = c;
-}
-
-static inline void flush(void)
-{
-}
-
-/*
- * Macros to configure UART1 and debug UART
- */
-#define _DEBUG_LL_ENTRY(mach, dbg_uart, dbg_shft, dbg_id)		\
-	if (machine_is_##mach()) {					\
-		uart_base = (volatile u8 *)(dbg_uart);			\
-		uart_shift = (dbg_shft);				\
-		port = (dbg_id);					\
-		set_omap_uart_info(port);				\
-		break;							\
-	}
-
-#define DEBUG_LL_OMAP7XX(p, mach)					\
-	_DEBUG_LL_ENTRY(mach, OMAP1_UART##p##_BASE, OMAP7XX_PORT_SHIFT,	\
-		OMAP1UART##p)
-
-#define DEBUG_LL_OMAP1(p, mach)						\
-	_DEBUG_LL_ENTRY(mach, OMAP1_UART##p##_BASE, OMAP_PORT_SHIFT,	\
-		OMAP1UART##p)
-
-static inline void arch_decomp_setup(void)
-{
-	int port = 0;
-
-	/*
-	 * Initialize the port based on the machine ID from the bootloader.
-	 * Note that we're using macros here instead of switch statement
-	 * as machine_is functions are optimized out for the boards that
-	 * are not selected.
-	 */
-	do {
-		/* omap7xx/8xx based boards using UART1 with shift 0 */
-		DEBUG_LL_OMAP7XX(1, herald);
-		DEBUG_LL_OMAP7XX(1, omap_perseus2);
-
-		/* omap15xx/16xx based boards using UART1 */
-		DEBUG_LL_OMAP1(1, ams_delta);
-		DEBUG_LL_OMAP1(1, nokia770);
-		DEBUG_LL_OMAP1(1, omap_h2);
-		DEBUG_LL_OMAP1(1, omap_h3);
-		DEBUG_LL_OMAP1(1, omap_innovator);
-		DEBUG_LL_OMAP1(1, omap_osk);
-		DEBUG_LL_OMAP1(1, omap_palmte);
-		DEBUG_LL_OMAP1(1, omap_palmz71);
-
-		/* omap15xx/16xx based boards using UART2 */
-		DEBUG_LL_OMAP1(2, omap_palmtt);
-
-		/* omap15xx/16xx based boards using UART3 */
-		DEBUG_LL_OMAP1(3, sx1);
-	} while (0);
-}
diff --git a/arch/arm/mach-omap1/include/mach/usb.h b/arch/arm/mach-omap1/include/mach/usb.h
deleted file mode 100644
index 5429d86c7190..000000000000
--- a/arch/arm/mach-omap1/include/mach/usb.h
+++ /dev/null
@@ -1,128 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-/*
- * FIXME correct answer depends on hmc_mode,
- * as does (on omap1) any nonzero value for config->otg port number
- */
-#if IS_ENABLED(CONFIG_USB_OMAP)
-#define	is_usb0_device(config)	1
-#else
-#define	is_usb0_device(config)	0
-#endif
-
-#include <linux/platform_data/usb-omap1.h>
-
-#if IS_ENABLED(CONFIG_USB_SUPPORT)
-void omap1_usb_init(struct omap_usb_config *pdata);
-#else
-static inline void omap1_usb_init(struct omap_usb_config *pdata)
-{
-}
-#endif
-
-#define OMAP1_OTG_BASE			0xfffb0400
-#define OMAP1_UDC_BASE			0xfffb4000
-#define OMAP1_OHCI_BASE			0xfffba000
-
-#define OMAP2_OHCI_BASE			0x4805e000
-#define OMAP2_UDC_BASE			0x4805e200
-#define OMAP2_OTG_BASE			0x4805e300
-#define OTG_BASE			OMAP1_OTG_BASE
-#define UDC_BASE			OMAP1_UDC_BASE
-#define OMAP_OHCI_BASE			OMAP1_OHCI_BASE
-
-/*
- * OTG and transceiver registers, for OMAPs starting with ARM926
- */
-#define OTG_REV				(OTG_BASE + 0x00)
-#define OTG_SYSCON_1			(OTG_BASE + 0x04)
-#	define	 USB2_TRX_MODE(w)	(((w)>>24)&0x07)
-#	define	 USB1_TRX_MODE(w)	(((w)>>20)&0x07)
-#	define	 USB0_TRX_MODE(w)	(((w)>>16)&0x07)
-#	define	 OTG_IDLE_EN		(1 << 15)
-#	define	 HST_IDLE_EN		(1 << 14)
-#	define	 DEV_IDLE_EN		(1 << 13)
-#	define	 OTG_RESET_DONE		(1 << 2)
-#	define	 OTG_SOFT_RESET		(1 << 1)
-#define OTG_SYSCON_2			(OTG_BASE + 0x08)
-#	define	 OTG_EN			(1 << 31)
-#	define	 USBX_SYNCHRO		(1 << 30)
-#	define	 OTG_MST16		(1 << 29)
-#	define	 SRP_GPDATA		(1 << 28)
-#	define	 SRP_GPDVBUS		(1 << 27)
-#	define	 SRP_GPUVBUS(w)		(((w)>>24)&0x07)
-#	define	 A_WAIT_VRISE(w)	(((w)>>20)&0x07)
-#	define	 B_ASE_BRST(w)		(((w)>>16)&0x07)
-#	define	 SRP_DPW		(1 << 14)
-#	define	 SRP_DATA		(1 << 13)
-#	define	 SRP_VBUS		(1 << 12)
-#	define	 OTG_PADEN		(1 << 10)
-#	define	 HMC_PADEN		(1 << 9)
-#	define	 UHOST_EN		(1 << 8)
-#	define	 HMC_TLLSPEED		(1 << 7)
-#	define	 HMC_TLLATTACH		(1 << 6)
-#	define	 OTG_HMC(w)		(((w)>>0)&0x3f)
-#define OTG_CTRL			(OTG_BASE + 0x0c)
-#	define	 OTG_USB2_EN		(1 << 29)
-#	define	 OTG_USB2_DP		(1 << 28)
-#	define	 OTG_USB2_DM		(1 << 27)
-#	define	 OTG_USB1_EN		(1 << 26)
-#	define	 OTG_USB1_DP		(1 << 25)
-#	define	 OTG_USB1_DM		(1 << 24)
-#	define	 OTG_USB0_EN		(1 << 23)
-#	define	 OTG_USB0_DP		(1 << 22)
-#	define	 OTG_USB0_DM		(1 << 21)
-#	define	 OTG_ASESSVLD		(1 << 20)
-#	define	 OTG_BSESSEND		(1 << 19)
-#	define	 OTG_BSESSVLD		(1 << 18)
-#	define	 OTG_VBUSVLD		(1 << 17)
-#	define	 OTG_ID			(1 << 16)
-#	define	 OTG_DRIVER_SEL		(1 << 15)
-#	define	 OTG_A_SETB_HNPEN	(1 << 12)
-#	define	 OTG_A_BUSREQ		(1 << 11)
-#	define	 OTG_B_HNPEN		(1 << 9)
-#	define	 OTG_B_BUSREQ		(1 << 8)
-#	define	 OTG_BUSDROP		(1 << 7)
-#	define	 OTG_PULLDOWN		(1 << 5)
-#	define	 OTG_PULLUP		(1 << 4)
-#	define	 OTG_DRV_VBUS		(1 << 3)
-#	define	 OTG_PD_VBUS		(1 << 2)
-#	define	 OTG_PU_VBUS		(1 << 1)
-#	define	 OTG_PU_ID		(1 << 0)
-#define OTG_IRQ_EN			(OTG_BASE + 0x10)	/* 16-bit */
-#	define	 DRIVER_SWITCH		(1 << 15)
-#	define	 A_VBUS_ERR		(1 << 13)
-#	define	 A_REQ_TMROUT		(1 << 12)
-#	define	 A_SRP_DETECT		(1 << 11)
-#	define	 B_HNP_FAIL		(1 << 10)
-#	define	 B_SRP_TMROUT		(1 << 9)
-#	define	 B_SRP_DONE		(1 << 8)
-#	define	 B_SRP_STARTED		(1 << 7)
-#	define	 OPRT_CHG		(1 << 0)
-#define OTG_IRQ_SRC			(OTG_BASE + 0x14)	/* 16-bit */
-	// same bits as in IRQ_EN
-#define OTG_OUTCTRL			(OTG_BASE + 0x18)	/* 16-bit */
-#	define	 OTGVPD			(1 << 14)
-#	define	 OTGVPU			(1 << 13)
-#	define	 OTGPUID		(1 << 12)
-#	define	 USB2VDR		(1 << 10)
-#	define	 USB2PDEN		(1 << 9)
-#	define	 USB2PUEN		(1 << 8)
-#	define	 USB1VDR		(1 << 6)
-#	define	 USB1PDEN		(1 << 5)
-#	define	 USB1PUEN		(1 << 4)
-#	define	 USB0VDR		(1 << 2)
-#	define	 USB0PDEN		(1 << 1)
-#	define	 USB0PUEN		(1 << 0)
-#define OTG_TEST			(OTG_BASE + 0x20)	/* 16-bit */
-#define OTG_VENDOR_CODE			(OTG_BASE + 0xfc)	/* 16-bit */
-
-/*-------------------------------------------------------------------------*/
-
-/* OMAP1 */
-#define	USB_TRANSCEIVER_CTRL		(0xfffe1000 + 0x0064)
-#	define	CONF_USB2_UNI_R		(1 << 8)
-#	define	CONF_USB1_UNI_R		(1 << 7)
-#	define	CONF_USB_PORT0_R(x)	(((x)>>4)&0x7)
-#	define	CONF_USB0_ISOLATE_R	(1 << 3)
-#	define	CONF_USB_PWRDN_DM_R	(1 << 2)
-#	define	CONF_USB_PWRDN_DP_R	(1 << 1)
diff --git a/arch/arm/mach-omap1/io.c b/arch/arm/mach-omap1/io.c
index 5a173fc2a1ca..d2db9b8aed3f 100644
--- a/arch/arm/mach-omap1/io.c
+++ b/arch/arm/mach-omap1/io.c
@@ -9,17 +9,14 @@
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/io.h>
+#include <linux/omap-dma.h>
 
 #include <asm/tlb.h>
 #include <asm/mach/map.h>
 
-#include <mach/mux.h>
-#include <mach/tc.h>
-#include <linux/omap-dma.h>
-
+#include "tc.h"
 #include "iomap.h"
 #include "common.h"
-#include "clock.h"
 
 /*
  * The machine specific code may provide the extra mapping besides the
@@ -126,11 +123,6 @@ void __init omap1_init_early(void)
 	 */
 	omap_writew(0x0, MPU_PUBLIC_TIPB_CNTL);
 	omap_writew(0x0, MPU_PRIVATE_TIPB_CNTL);
-
-	/* Must init clocks early to assure that timer interrupt works
-	 */
-	omap1_clk_init();
-	omap1_mux_init();
 }
 
 void __init omap1_init_late(void)
diff --git a/arch/arm/mach-omap1/irq.c b/arch/arm/mach-omap1/irq.c
index ee6a93083154..70868e9f19ac 100644
--- a/arch/arm/mach-omap1/irq.c
+++ b/arch/arm/mach-omap1/irq.c
@@ -47,9 +47,7 @@
 #include <asm/mach/irq.h>
 
 #include "soc.h"
-
-#include <mach/hardware.h>
-
+#include "hardware.h"
 #include "common.h"
 
 #define IRQ_BANK(irq) ((irq) >> 5)
diff --git a/arch/arm/mach-omap1/irqs.h b/arch/arm/mach-omap1/irqs.h
new file mode 100644
index 000000000000..2851acfe5ff3
--- /dev/null
+++ b/arch/arm/mach-omap1/irqs.h
@@ -0,0 +1,249 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ *  Copyright (C) Greg Lonnon 2001
+ *  Updated for OMAP-1610 by Tony Lindgren <tony@atomide.com>
+ *
+ * Copyright (C) 2009 Texas Instruments
+ * Added OMAP4 support - Santosh Shilimkar <santosh.shilimkar@ti.com>
+ *
+ * NOTE: The interrupt vectors for the OMAP-1509, OMAP-1510, and OMAP-1610
+ *	 are different.
+ */
+
+#ifndef __ASM_ARCH_OMAP15XX_IRQS_H
+#define __ASM_ARCH_OMAP15XX_IRQS_H
+
+/*
+ * IRQ numbers for interrupt handler 1
+ *
+ * NOTE: See also the OMAP-1510 and 1610 specific IRQ numbers below
+ *
+ */
+#define INT_CAMERA		(NR_IRQS_LEGACY + 1)
+#define INT_FIQ			(NR_IRQS_LEGACY + 3)
+#define INT_RTDX		(NR_IRQS_LEGACY + 6)
+#define INT_DSP_MMU_ABORT	(NR_IRQS_LEGACY + 7)
+#define INT_HOST		(NR_IRQS_LEGACY + 8)
+#define INT_ABORT		(NR_IRQS_LEGACY + 9)
+#define INT_BRIDGE_PRIV		(NR_IRQS_LEGACY + 13)
+#define INT_GPIO_BANK1		(NR_IRQS_LEGACY + 14)
+#define INT_UART3		(NR_IRQS_LEGACY + 15)
+#define INT_TIMER3		(NR_IRQS_LEGACY + 16)
+#define INT_DMA_CH0_6		(NR_IRQS_LEGACY + 19)
+#define INT_DMA_CH1_7		(NR_IRQS_LEGACY + 20)
+#define INT_DMA_CH2_8		(NR_IRQS_LEGACY + 21)
+#define INT_DMA_CH3		(NR_IRQS_LEGACY + 22)
+#define INT_DMA_CH4		(NR_IRQS_LEGACY + 23)
+#define INT_DMA_CH5		(NR_IRQS_LEGACY + 24)
+#define INT_TIMER1		(NR_IRQS_LEGACY + 26)
+#define INT_WD_TIMER		(NR_IRQS_LEGACY + 27)
+#define INT_BRIDGE_PUB		(NR_IRQS_LEGACY + 28)
+#define INT_TIMER2		(NR_IRQS_LEGACY + 30)
+#define INT_LCD_CTRL		(NR_IRQS_LEGACY + 31)
+
+/*
+ * OMAP-1510 specific IRQ numbers for interrupt handler 1
+ */
+#define INT_1510_IH2_IRQ	(NR_IRQS_LEGACY + 0)
+#define INT_1510_RES2		(NR_IRQS_LEGACY + 2)
+#define INT_1510_SPI_TX		(NR_IRQS_LEGACY + 4)
+#define INT_1510_SPI_RX		(NR_IRQS_LEGACY + 5)
+#define INT_1510_DSP_MAILBOX1	(NR_IRQS_LEGACY + 10)
+#define INT_1510_DSP_MAILBOX2	(NR_IRQS_LEGACY + 11)
+#define INT_1510_RES12		(NR_IRQS_LEGACY + 12)
+#define INT_1510_LB_MMU		(NR_IRQS_LEGACY + 17)
+#define INT_1510_RES18		(NR_IRQS_LEGACY + 18)
+#define INT_1510_LOCAL_BUS	(NR_IRQS_LEGACY + 29)
+
+/*
+ * OMAP-1610 specific IRQ numbers for interrupt handler 1
+ */
+#define INT_1610_IH2_IRQ	INT_1510_IH2_IRQ
+#define INT_1610_IH2_FIQ	(NR_IRQS_LEGACY + 2)
+#define INT_1610_McBSP2_TX	(NR_IRQS_LEGACY + 4)
+#define INT_1610_McBSP2_RX	(NR_IRQS_LEGACY + 5)
+#define INT_1610_DSP_MAILBOX1	(NR_IRQS_LEGACY + 10)
+#define INT_1610_DSP_MAILBOX2	(NR_IRQS_LEGACY + 11)
+#define INT_1610_LCD_LINE	(NR_IRQS_LEGACY + 12)
+#define INT_1610_GPTIMER1	(NR_IRQS_LEGACY + 17)
+#define INT_1610_GPTIMER2	(NR_IRQS_LEGACY + 18)
+#define INT_1610_SSR_FIFO_0	(NR_IRQS_LEGACY + 29)
+
+/*
+ * OMAP-7xx specific IRQ numbers for interrupt handler 1
+ */
+#define INT_7XX_IH2_FIQ		(NR_IRQS_LEGACY + 0)
+#define INT_7XX_IH2_IRQ		(NR_IRQS_LEGACY + 1)
+#define INT_7XX_USB_NON_ISO	(NR_IRQS_LEGACY + 2)
+#define INT_7XX_USB_ISO		(NR_IRQS_LEGACY + 3)
+#define INT_7XX_ICR		(NR_IRQS_LEGACY + 4)
+#define INT_7XX_EAC		(NR_IRQS_LEGACY + 5)
+#define INT_7XX_GPIO_BANK1	(NR_IRQS_LEGACY + 6)
+#define INT_7XX_GPIO_BANK2	(NR_IRQS_LEGACY + 7)
+#define INT_7XX_GPIO_BANK3	(NR_IRQS_LEGACY + 8)
+#define INT_7XX_McBSP2TX	(NR_IRQS_LEGACY + 10)
+#define INT_7XX_McBSP2RX	(NR_IRQS_LEGACY + 11)
+#define INT_7XX_McBSP2RX_OVF	(NR_IRQS_LEGACY + 12)
+#define INT_7XX_LCD_LINE	(NR_IRQS_LEGACY + 14)
+#define INT_7XX_GSM_PROTECT	(NR_IRQS_LEGACY + 15)
+#define INT_7XX_TIMER3		(NR_IRQS_LEGACY + 16)
+#define INT_7XX_GPIO_BANK5	(NR_IRQS_LEGACY + 17)
+#define INT_7XX_GPIO_BANK6	(NR_IRQS_LEGACY + 18)
+#define INT_7XX_SPGIO_WR	(NR_IRQS_LEGACY + 29)
+
+/*
+ * IRQ numbers for interrupt handler 2
+ *
+ * NOTE: See also the OMAP-1510 and 1610 specific IRQ numbers below
+ */
+#define IH2_BASE		(NR_IRQS_LEGACY + 32)
+
+#define INT_KEYBOARD		(1 + IH2_BASE)
+#define INT_uWireTX		(2 + IH2_BASE)
+#define INT_uWireRX		(3 + IH2_BASE)
+#define INT_I2C			(4 + IH2_BASE)
+#define INT_MPUIO		(5 + IH2_BASE)
+#define INT_USB_HHC_1		(6 + IH2_BASE)
+#define INT_McBSP3TX		(10 + IH2_BASE)
+#define INT_McBSP3RX		(11 + IH2_BASE)
+#define INT_McBSP1TX		(12 + IH2_BASE)
+#define INT_McBSP1RX		(13 + IH2_BASE)
+#define INT_UART1		(14 + IH2_BASE)
+#define INT_UART2		(15 + IH2_BASE)
+#define INT_BT_MCSI1TX		(16 + IH2_BASE)
+#define INT_BT_MCSI1RX		(17 + IH2_BASE)
+#define INT_SOSSI_MATCH		(19 + IH2_BASE)
+#define INT_USB_W2FC		(20 + IH2_BASE)
+#define INT_1WIRE		(21 + IH2_BASE)
+#define INT_OS_TIMER		(22 + IH2_BASE)
+#define INT_MMC			(23 + IH2_BASE)
+#define INT_GAUGE_32K		(24 + IH2_BASE)
+#define INT_RTC_TIMER		(25 + IH2_BASE)
+#define INT_RTC_ALARM		(26 + IH2_BASE)
+#define INT_MEM_STICK		(27 + IH2_BASE)
+
+/*
+ * OMAP-1510 specific IRQ numbers for interrupt handler 2
+ */
+#define INT_1510_DSP_MMU	(28 + IH2_BASE)
+#define INT_1510_COM_SPI_RO	(31 + IH2_BASE)
+
+/*
+ * OMAP-1610 specific IRQ numbers for interrupt handler 2
+ */
+#define INT_1610_FAC		(0 + IH2_BASE)
+#define INT_1610_USB_HHC_2	(7 + IH2_BASE)
+#define INT_1610_USB_OTG	(8 + IH2_BASE)
+#define INT_1610_SoSSI		(9 + IH2_BASE)
+#define INT_1610_SoSSI_MATCH	(19 + IH2_BASE)
+#define INT_1610_DSP_MMU	(28 + IH2_BASE)
+#define INT_1610_McBSP2RX_OF	(31 + IH2_BASE)
+#define INT_1610_STI		(32 + IH2_BASE)
+#define INT_1610_STI_WAKEUP	(33 + IH2_BASE)
+#define INT_1610_GPTIMER3	(34 + IH2_BASE)
+#define INT_1610_GPTIMER4	(35 + IH2_BASE)
+#define INT_1610_GPTIMER5	(36 + IH2_BASE)
+#define INT_1610_GPTIMER6	(37 + IH2_BASE)
+#define INT_1610_GPTIMER7	(38 + IH2_BASE)
+#define INT_1610_GPTIMER8	(39 + IH2_BASE)
+#define INT_1610_GPIO_BANK2	(40 + IH2_BASE)
+#define INT_1610_GPIO_BANK3	(41 + IH2_BASE)
+#define INT_1610_MMC2		(42 + IH2_BASE)
+#define INT_1610_CF		(43 + IH2_BASE)
+#define INT_1610_WAKE_UP_REQ	(46 + IH2_BASE)
+#define INT_1610_GPIO_BANK4	(48 + IH2_BASE)
+#define INT_1610_SPI		(49 + IH2_BASE)
+#define INT_1610_DMA_CH6	(53 + IH2_BASE)
+#define INT_1610_DMA_CH7	(54 + IH2_BASE)
+#define INT_1610_DMA_CH8	(55 + IH2_BASE)
+#define INT_1610_DMA_CH9	(56 + IH2_BASE)
+#define INT_1610_DMA_CH10	(57 + IH2_BASE)
+#define INT_1610_DMA_CH11	(58 + IH2_BASE)
+#define INT_1610_DMA_CH12	(59 + IH2_BASE)
+#define INT_1610_DMA_CH13	(60 + IH2_BASE)
+#define INT_1610_DMA_CH14	(61 + IH2_BASE)
+#define INT_1610_DMA_CH15	(62 + IH2_BASE)
+#define INT_1610_NAND		(63 + IH2_BASE)
+#define INT_1610_SHA1MD5	(91 + IH2_BASE)
+
+/*
+ * OMAP-7xx specific IRQ numbers for interrupt handler 2
+ */
+#define INT_7XX_HW_ERRORS	(0 + IH2_BASE)
+#define INT_7XX_NFIQ_PWR_FAIL	(1 + IH2_BASE)
+#define INT_7XX_CFCD		(2 + IH2_BASE)
+#define INT_7XX_CFIREQ		(3 + IH2_BASE)
+#define INT_7XX_I2C		(4 + IH2_BASE)
+#define INT_7XX_PCC		(5 + IH2_BASE)
+#define INT_7XX_MPU_EXT_NIRQ	(6 + IH2_BASE)
+#define INT_7XX_SPI_100K_1	(7 + IH2_BASE)
+#define INT_7XX_SYREN_SPI	(8 + IH2_BASE)
+#define INT_7XX_VLYNQ		(9 + IH2_BASE)
+#define INT_7XX_GPIO_BANK4	(10 + IH2_BASE)
+#define INT_7XX_McBSP1TX	(11 + IH2_BASE)
+#define INT_7XX_McBSP1RX	(12 + IH2_BASE)
+#define INT_7XX_McBSP1RX_OF	(13 + IH2_BASE)
+#define INT_7XX_UART_MODEM_IRDA_2 (14 + IH2_BASE)
+#define INT_7XX_UART_MODEM_1	(15 + IH2_BASE)
+#define INT_7XX_MCSI		(16 + IH2_BASE)
+#define INT_7XX_uWireTX		(17 + IH2_BASE)
+#define INT_7XX_uWireRX		(18 + IH2_BASE)
+#define INT_7XX_SMC_CD		(19 + IH2_BASE)
+#define INT_7XX_SMC_IREQ	(20 + IH2_BASE)
+#define INT_7XX_HDQ_1WIRE	(21 + IH2_BASE)
+#define INT_7XX_TIMER32K	(22 + IH2_BASE)
+#define INT_7XX_MMC_SDIO	(23 + IH2_BASE)
+#define INT_7XX_UPLD		(24 + IH2_BASE)
+#define INT_7XX_USB_HHC_1	(27 + IH2_BASE)
+#define INT_7XX_USB_HHC_2	(28 + IH2_BASE)
+#define INT_7XX_USB_GENI	(29 + IH2_BASE)
+#define INT_7XX_USB_OTG		(30 + IH2_BASE)
+#define INT_7XX_CAMERA_IF	(31 + IH2_BASE)
+#define INT_7XX_RNG		(32 + IH2_BASE)
+#define INT_7XX_DUAL_MODE_TIMER (33 + IH2_BASE)
+#define INT_7XX_DBB_RF_EN	(34 + IH2_BASE)
+#define INT_7XX_MPUIO_KEYPAD	(35 + IH2_BASE)
+#define INT_7XX_SHA1_MD5	(36 + IH2_BASE)
+#define INT_7XX_SPI_100K_2	(37 + IH2_BASE)
+#define INT_7XX_RNG_IDLE	(38 + IH2_BASE)
+#define INT_7XX_MPUIO		(39 + IH2_BASE)
+#define INT_7XX_LLPC_LCD_CTRL_CAN_BE_OFF	(40 + IH2_BASE)
+#define INT_7XX_LLPC_OE_FALLING (41 + IH2_BASE)
+#define INT_7XX_LLPC_OE_RISING	(42 + IH2_BASE)
+#define INT_7XX_LLPC_VSYNC	(43 + IH2_BASE)
+#define INT_7XX_WAKE_UP_REQ	(46 + IH2_BASE)
+#define INT_7XX_DMA_CH6		(53 + IH2_BASE)
+#define INT_7XX_DMA_CH7		(54 + IH2_BASE)
+#define INT_7XX_DMA_CH8		(55 + IH2_BASE)
+#define INT_7XX_DMA_CH9		(56 + IH2_BASE)
+#define INT_7XX_DMA_CH10	(57 + IH2_BASE)
+#define INT_7XX_DMA_CH11	(58 + IH2_BASE)
+#define INT_7XX_DMA_CH12	(59 + IH2_BASE)
+#define INT_7XX_DMA_CH13	(60 + IH2_BASE)
+#define INT_7XX_DMA_CH14	(61 + IH2_BASE)
+#define INT_7XX_DMA_CH15	(62 + IH2_BASE)
+#define INT_7XX_NAND		(63 + IH2_BASE)
+
+/* Max. 128 level 2 IRQs (OMAP1610), 192 GPIOs (OMAP730/850) and
+ * 16 MPUIO lines */
+#define OMAP_MAX_GPIO_LINES	192
+#define IH_GPIO_BASE		(128 + IH2_BASE)
+#define IH_MPUIO_BASE		(OMAP_MAX_GPIO_LINES + IH_GPIO_BASE)
+#define OMAP_IRQ_END		(IH_MPUIO_BASE + 16)
+
+/* External FPGA handles interrupts on Innovator boards */
+#define	OMAP_FPGA_IRQ_BASE	(OMAP_IRQ_END)
+#ifdef	CONFIG_MACH_OMAP_INNOVATOR
+#define OMAP_FPGA_NR_IRQS	24
+#else
+#define OMAP_FPGA_NR_IRQS	0
+#endif
+#define OMAP_FPGA_IRQ_END	(OMAP_FPGA_IRQ_BASE + OMAP_FPGA_NR_IRQS)
+
+#define OMAP_IRQ_BIT(irq)	(1 << ((irq - NR_IRQS_LEGACY) % 32))
+
+#ifdef CONFIG_FIQ
+#define FIQ_START		1024
+#endif
+
+#endif
diff --git a/arch/arm/mach-omap1/mcbsp.c b/arch/arm/mach-omap1/mcbsp.c
index f36c34f47f11..05c25c432449 100644
--- a/arch/arm/mach-omap1/mcbsp.c
+++ b/arch/arm/mach-omap1/mcbsp.c
@@ -15,14 +15,13 @@
 #include <linux/io.h>
 #include <linux/platform_device.h>
 #include <linux/slab.h>
-
 #include <linux/omap-dma.h>
-#include <mach/mux.h>
-#include "soc.h"
+#include <linux/soc/ti/omap1-io.h>
 #include <linux/platform_data/asoc-ti-mcbsp.h>
 
-#include <mach/irqs.h>
-
+#include "mux.h"
+#include "soc.h"
+#include "irqs.h"
 #include "iomap.h"
 
 #define DPS_RSTCT2_PER_EN	(1 << 0)
@@ -44,8 +43,8 @@ static void omap1_mcbsp_request(unsigned int id)
 			api_clk = clk_get(NULL, "api_ck");
 			dsp_clk = clk_get(NULL, "dsp_ck");
 			if (!IS_ERR(api_clk) && !IS_ERR(dsp_clk)) {
-				clk_enable(api_clk);
-				clk_enable(dsp_clk);
+				clk_prepare_enable(api_clk);
+				clk_prepare_enable(dsp_clk);
 
 				/*
 				 * DSP external peripheral reset
@@ -63,11 +62,11 @@ static void omap1_mcbsp_free(unsigned int id)
 	if (id == 0 || id == 2) {
 		if (--dsp_use == 0) {
 			if (!IS_ERR(api_clk)) {
-				clk_disable(api_clk);
+				clk_disable_unprepare(api_clk);
 				clk_put(api_clk);
 			}
 			if (!IS_ERR(dsp_clk)) {
-				clk_disable(dsp_clk);
+				clk_disable_unprepare(dsp_clk);
 				clk_put(dsp_clk);
 			}
 		}
diff --git a/arch/arm/mach-omap1/mtd-xip.h b/arch/arm/mach-omap1/mtd-xip.h
new file mode 100644
index 000000000000..5ae312ff08a1
--- /dev/null
+++ b/arch/arm/mach-omap1/mtd-xip.h
@@ -0,0 +1,60 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * MTD primitives for XIP support. Architecture specific functions.
+ *
+ * Do not include this file directly. It's included from linux/mtd/xip.h
+ *
+ * Author: Vladimir Barinov <vbarinov@embeddedalley.com>
+ *
+ * (c) 2005 MontaVista Software, Inc.
+ */
+
+#ifndef __ARCH_OMAP_MTD_XIP_H__
+#define __ARCH_OMAP_MTD_XIP_H__
+
+#include "hardware.h"
+#include <linux/soc/ti/omap1-io.h>
+#define OMAP_MPU_TIMER_BASE	(0xfffec500)
+#define OMAP_MPU_TIMER_OFFSET	0x100
+
+typedef struct {
+	u32 cntl;			/* CNTL_TIMER, R/W */
+	u32 load_tim;			/* LOAD_TIM,   W */
+	u32 read_tim;			/* READ_TIM,   R */
+} xip_omap_mpu_timer_regs_t;
+
+#define xip_omap_mpu_timer_base(n)					\
+((volatile xip_omap_mpu_timer_regs_t*)OMAP1_IO_ADDRESS(OMAP_MPU_TIMER_BASE +	\
+	(n)*OMAP_MPU_TIMER_OFFSET))
+
+static inline unsigned long xip_omap_mpu_timer_read(int nr)
+{
+	volatile xip_omap_mpu_timer_regs_t* timer = xip_omap_mpu_timer_base(nr);
+	return timer->read_tim;
+}
+
+#define xip_irqpending()	\
+	(omap_readl(OMAP_IH1_ITR) & ~omap_readl(OMAP_IH1_MIR))
+#define xip_currtime()		(~xip_omap_mpu_timer_read(0))
+
+/*
+ * It's permitted to do approximation for xip_elapsed_since macro
+ * (see linux/mtd/xip.h)
+ */
+
+#ifdef CONFIG_MACH_OMAP_PERSEUS2
+#define xip_elapsed_since(x)	(signed)((~xip_omap_mpu_timer_read(0) - (x)) / 7)
+#else
+#define xip_elapsed_since(x)	(signed)((~xip_omap_mpu_timer_read(0) - (x)) / 6)
+#endif
+
+/*
+ * xip_cpu_idle() is used when waiting for a delay equal or larger than
+ * the system timer tick period.  This should put the CPU into idle mode
+ * to save power and to be woken up only when some interrupts are pending.
+ * As above, this should not rely upon standard kernel code.
+ */
+
+#define xip_cpu_idle()  asm volatile ("mcr p15, 0, %0, c7, c0, 4" :: "r" (1))
+
+#endif /* __ARCH_OMAP_MTD_XIP_H__ */
diff --git a/arch/arm/mach-omap1/mux.c b/arch/arm/mach-omap1/mux.c
index 972665bf52d6..2d9458ff1d29 100644
--- a/arch/arm/mach-omap1/mux.c
+++ b/arch/arm/mach-omap1/mux.c
@@ -12,10 +12,10 @@
 #include <linux/init.h>
 #include <linux/io.h>
 #include <linux/spinlock.h>
+#include <linux/soc/ti/omap1-io.h>
 
-#include <mach/hardware.h>
-
-#include <mach/mux.h>
+#include "hardware.h"
+#include "mux.h"
 
 #ifdef CONFIG_OMAP_MUX
 
diff --git a/arch/arm/mach-omap1/mux.h b/arch/arm/mach-omap1/mux.h
new file mode 100644
index 000000000000..3e7ed3348a55
--- /dev/null
+++ b/arch/arm/mach-omap1/mux.h
@@ -0,0 +1,144 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * Table of the Omap register configurations for the FUNC_MUX and
+ * PULL_DWN combinations.
+ *
+ * Copyright (C) 2004 - 2008 Texas Instruments Inc.
+ * Copyright (C) 2003 - 2008 Nokia Corporation
+ *
+ * Written by Tony Lindgren
+ *
+ * NOTE: Please use the following naming style for new pin entries.
+ *	 For example, W8_1610_MMC2_DAT0, where:
+ *	 - W8	     = ball
+ *	 - 1610	     = 1510 or 1610, none if common for both 1510 and 1610
+ *	 - MMC2_DAT0 = function
+ */
+
+#ifndef __ASM_ARCH_MUX_H
+#define __ASM_ARCH_MUX_H
+
+#include <linux/soc/ti/omap1-mux.h>
+
+#define PU_PD_SEL_NA		0	/* No pu_pd reg available */
+#define PULL_DWN_CTRL_NA	0	/* No pull-down control needed */
+
+#ifdef	CONFIG_OMAP_MUX_DEBUG
+#define MUX_REG(reg, mode_offset, mode) .mux_reg_name = "FUNC_MUX_CTRL_"#reg, \
+					.mux_reg = FUNC_MUX_CTRL_##reg, \
+					.mask_offset = mode_offset, \
+					.mask = mode,
+
+#define PULL_REG(reg, bit, status)	.pull_name = "PULL_DWN_CTRL_"#reg, \
+					.pull_reg = PULL_DWN_CTRL_##reg, \
+					.pull_bit = bit, \
+					.pull_val = status,
+
+#define PU_PD_REG(reg, status)		.pu_pd_name = "PU_PD_SEL_"#reg, \
+					.pu_pd_reg = PU_PD_SEL_##reg, \
+					.pu_pd_val = status,
+
+#define MUX_REG_7XX(reg, mode_offset, mode) .mux_reg_name = "OMAP7XX_IO_CONF_"#reg, \
+					.mux_reg = OMAP7XX_IO_CONF_##reg, \
+					.mask_offset = mode_offset, \
+					.mask = mode,
+
+#define PULL_REG_7XX(reg, bit, status)	.pull_name = "OMAP7XX_IO_CONF_"#reg, \
+					.pull_reg = OMAP7XX_IO_CONF_##reg, \
+					.pull_bit = bit, \
+					.pull_val = status,
+
+#else
+
+#define MUX_REG(reg, mode_offset, mode) .mux_reg = FUNC_MUX_CTRL_##reg, \
+					.mask_offset = mode_offset, \
+					.mask = mode,
+
+#define PULL_REG(reg, bit, status)	.pull_reg = PULL_DWN_CTRL_##reg, \
+					.pull_bit = bit, \
+					.pull_val = status,
+
+#define PU_PD_REG(reg, status)		.pu_pd_reg = PU_PD_SEL_##reg, \
+					.pu_pd_val = status,
+
+#define MUX_REG_7XX(reg, mode_offset, mode) \
+					.mux_reg = OMAP7XX_IO_CONF_##reg, \
+					.mask_offset = mode_offset, \
+					.mask = mode,
+
+#define PULL_REG_7XX(reg, bit, status)	.pull_reg = OMAP7XX_IO_CONF_##reg, \
+					.pull_bit = bit, \
+					.pull_val = status,
+
+#endif /* CONFIG_OMAP_MUX_DEBUG */
+
+#define MUX_CFG(desc, mux_reg, mode_offset, mode,	\
+		pull_reg, pull_bit, pull_status,	\
+		pu_pd_reg, pu_pd_status, debug_status)	\
+{							\
+	.name =	 desc,					\
+	.debug = debug_status,				\
+	MUX_REG(mux_reg, mode_offset, mode)		\
+	PULL_REG(pull_reg, pull_bit, pull_status)	\
+	PU_PD_REG(pu_pd_reg, pu_pd_status)		\
+},
+
+
+/*
+ * OMAP730/850 has a slightly different config for the pin mux.
+ * - config regs are the OMAP7XX_IO_CONF_x regs (see omap7xx.h) regs and
+ *   not the FUNC_MUX_CTRL_x regs from hardware.h
+ * - for pull-up/down, only has one enable bit which is in the same register
+ *   as mux config
+ */
+#define MUX_CFG_7XX(desc, mux_reg, mode_offset, mode,	\
+		   pull_bit, pull_status, debug_status)\
+{							\
+	.name =	 desc,					\
+	.debug = debug_status,				\
+	MUX_REG_7XX(mux_reg, mode_offset, mode)		\
+	PULL_REG_7XX(mux_reg, pull_bit, pull_status)	\
+	PU_PD_REG(NA, 0)		\
+},
+
+struct pin_config {
+	char 			*name;
+	const unsigned int 	mux_reg;
+	unsigned char		debug;
+
+	const unsigned char mask_offset;
+	const unsigned char mask;
+
+	const char *pull_name;
+	const unsigned int pull_reg;
+	const unsigned char pull_val;
+	const unsigned char pull_bit;
+
+	const char *pu_pd_name;
+	const unsigned int pu_pd_reg;
+	const unsigned char pu_pd_val;
+
+#if	defined(CONFIG_OMAP_MUX_DEBUG) || defined(CONFIG_OMAP_MUX_WARNINGS)
+	const char *mux_reg_name;
+#endif
+
+};
+
+struct omap_mux_cfg {
+	struct pin_config	*pins;
+	unsigned long		size;
+	int			(*cfg_reg)(const struct pin_config *cfg);
+};
+
+#ifdef	CONFIG_OMAP_MUX
+/* setup pin muxing in Linux */
+extern int omap1_mux_init(void);
+extern int omap_mux_register(struct omap_mux_cfg *);
+#else
+/* boot loader does it all (no warnings from CONFIG_OMAP_MUX_WARNINGS) */
+static inline int omap1_mux_init(void) { return 0; }
+#endif
+
+extern int omap2_mux_init(void);
+
+#endif
diff --git a/arch/arm/mach-omap1/ocpi.c b/arch/arm/mach-omap1/ocpi.c
index 380ea2de58c1..d48f726571a4 100644
--- a/arch/arm/mach-omap1/ocpi.c
+++ b/arch/arm/mach-omap1/ocpi.c
@@ -20,9 +20,9 @@
 #include <linux/err.h>
 #include <linux/clk.h>
 #include <linux/io.h>
+#include <linux/soc/ti/omap1-io.h>
 
-#include <mach/hardware.h>
-
+#include "hardware.h"
 #include "common.h"
 
 #define OCPI_BASE		0xfffec320
@@ -73,7 +73,7 @@ static int __init omap_ocpi_init(void)
 	if (IS_ERR(ocpi_ck))
 		return PTR_ERR(ocpi_ck);
 
-	clk_enable(ocpi_ck);
+	clk_prepare_enable(ocpi_ck);
 	ocpi_enable();
 	pr_info("OMAP OCPI interconnect driver loaded\n");
 
@@ -87,7 +87,7 @@ static void __exit omap_ocpi_exit(void)
 	if (!cpu_is_omap16xx())
 		return;
 
-	clk_disable(ocpi_ck);
+	clk_disable_unprepare(ocpi_ck);
 	clk_put(ocpi_ck);
 }
 
diff --git a/arch/arm/mach-omap1/omap-dma.c b/arch/arm/mach-omap1/omap-dma.c
new file mode 100644
index 000000000000..f7e62de427f3
--- /dev/null
+++ b/arch/arm/mach-omap1/omap-dma.c
@@ -0,0 +1,884 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * linux/arch/arm/plat-omap/dma.c
+ *
+ * Copyright (C) 2003 - 2008 Nokia Corporation
+ * Author: Juha Yrjölä <juha.yrjola@nokia.com>
+ * DMA channel linking for 1610 by Samuel Ortiz <samuel.ortiz@nokia.com>
+ * Graphics DMA and LCD DMA graphics tranformations
+ * by Imre Deak <imre.deak@nokia.com>
+ * OMAP2/3 support Copyright (C) 2004-2007 Texas Instruments, Inc.
+ * Merged to support both OMAP1 and OMAP2 by Tony Lindgren <tony@atomide.com>
+ * Some functions based on earlier dma-omap.c Copyright (C) 2001 RidgeRun, Inc.
+ *
+ * Copyright (C) 2009 Texas Instruments
+ * Added OMAP4 support - Santosh Shilimkar <santosh.shilimkar@ti.com>
+ *
+ * Support functions for the OMAP internal DMA channels.
+ *
+ * Copyright (C) 2010 Texas Instruments Incorporated - https://www.ti.com/
+ * Converted DMA library into DMA platform driver.
+ *	- G, Manjunath Kondaiah <manjugk@ti.com>
+ */
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/sched.h>
+#include <linux/spinlock.h>
+#include <linux/errno.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/io.h>
+#include <linux/slab.h>
+#include <linux/delay.h>
+
+#include <linux/omap-dma.h>
+
+#include <linux/soc/ti/omap1-io.h>
+#include <linux/soc/ti/omap1-soc.h>
+
+#include "tc.h"
+
+/*
+ * MAX_LOGICAL_DMA_CH_COUNT: the maximum number of logical DMA
+ * channels that an instance of the SDMA IP block can support.  Used
+ * to size arrays.  (The actual maximum on a particular SoC may be less
+ * than this -- for example, OMAP1 SDMA instances only support 17 logical
+ * DMA channels.)
+ */
+#define MAX_LOGICAL_DMA_CH_COUNT		32
+
+#undef DEBUG
+
+#define OMAP_DMA_ACTIVE			0x01
+
+#define OMAP_FUNC_MUX_ARM_BASE		(0xfffe1000 + 0xec)
+
+static struct omap_system_dma_plat_info *p;
+static struct omap_dma_dev_attr *d;
+static int enable_1510_mode;
+static u32 errata;
+
+struct dma_link_info {
+	int *linked_dmach_q;
+	int no_of_lchs_linked;
+
+	int q_count;
+	int q_tail;
+	int q_head;
+
+	int chain_state;
+	int chain_mode;
+
+};
+
+static int dma_lch_count;
+static int dma_chan_count;
+static int omap_dma_reserve_channels;
+
+static DEFINE_SPINLOCK(dma_chan_lock);
+static struct omap_dma_lch *dma_chan;
+
+static inline void omap_disable_channel_irq(int lch)
+{
+	/* disable channel interrupts */
+	p->dma_write(0, CICR, lch);
+	/* Clear CSR */
+	p->dma_read(CSR, lch);
+}
+
+static inline void set_gdma_dev(int req, int dev)
+{
+	u32 reg = OMAP_FUNC_MUX_ARM_BASE + ((req - 1) / 5) * 4;
+	int shift = ((req - 1) % 5) * 6;
+	u32 l;
+
+	l = omap_readl(reg);
+	l &= ~(0x3f << shift);
+	l |= (dev - 1) << shift;
+	omap_writel(l, reg);
+}
+
+#if IS_ENABLED(CONFIG_FB_OMAP)
+void omap_set_dma_priority(int lch, int dst_port, int priority)
+{
+	unsigned long reg;
+	u32 l;
+
+	if (dma_omap1()) {
+		switch (dst_port) {
+		case OMAP_DMA_PORT_OCP_T1:	/* FFFECC00 */
+			reg = OMAP_TC_OCPT1_PRIOR;
+			break;
+		case OMAP_DMA_PORT_OCP_T2:	/* FFFECCD0 */
+			reg = OMAP_TC_OCPT2_PRIOR;
+			break;
+		case OMAP_DMA_PORT_EMIFF:	/* FFFECC08 */
+			reg = OMAP_TC_EMIFF_PRIOR;
+			break;
+		case OMAP_DMA_PORT_EMIFS:	/* FFFECC04 */
+			reg = OMAP_TC_EMIFS_PRIOR;
+			break;
+		default:
+			BUG();
+			return;
+		}
+		l = omap_readl(reg);
+		l &= ~(0xf << 8);
+		l |= (priority & 0xf) << 8;
+		omap_writel(l, reg);
+	}
+}
+EXPORT_SYMBOL(omap_set_dma_priority);
+#endif
+
+#if IS_ENABLED(CONFIG_USB_OMAP)
+#ifdef CONFIG_ARCH_OMAP15XX
+/* Returns 1 if the DMA module is in OMAP1510-compatible mode, 0 otherwise */
+static int omap_dma_in_1510_mode(void)
+{
+	return enable_1510_mode;
+}
+#else
+#define omap_dma_in_1510_mode()		0
+#endif
+
+void omap_set_dma_transfer_params(int lch, int data_type, int elem_count,
+				  int frame_count, int sync_mode,
+				  int dma_trigger, int src_or_dst_synch)
+{
+	u32 l;
+	u16 ccr;
+
+	l = p->dma_read(CSDP, lch);
+	l &= ~0x03;
+	l |= data_type;
+	p->dma_write(l, CSDP, lch);
+
+	ccr = p->dma_read(CCR, lch);
+	ccr &= ~(1 << 5);
+	if (sync_mode == OMAP_DMA_SYNC_FRAME)
+		ccr |= 1 << 5;
+	p->dma_write(ccr, CCR, lch);
+
+	ccr = p->dma_read(CCR2, lch);
+	ccr &= ~(1 << 2);
+	if (sync_mode == OMAP_DMA_SYNC_BLOCK)
+		ccr |= 1 << 2;
+	p->dma_write(ccr, CCR2, lch);
+	p->dma_write(elem_count, CEN, lch);
+	p->dma_write(frame_count, CFN, lch);
+}
+EXPORT_SYMBOL(omap_set_dma_transfer_params);
+
+void omap_set_dma_channel_mode(int lch, enum omap_dma_channel_mode mode)
+{
+	if (!dma_omap15xx()) {
+		u32 l;
+
+		l = p->dma_read(LCH_CTRL, lch);
+		l &= ~0x7;
+		l |= mode;
+		p->dma_write(l, LCH_CTRL, lch);
+	}
+}
+EXPORT_SYMBOL(omap_set_dma_channel_mode);
+
+/* Note that src_port is only for omap1 */
+void omap_set_dma_src_params(int lch, int src_port, int src_amode,
+			     unsigned long src_start,
+			     int src_ei, int src_fi)
+{
+	u32 l;
+	u16 w;
+
+	w = p->dma_read(CSDP, lch);
+	w &= ~(0x1f << 2);
+	w |= src_port << 2;
+	p->dma_write(w, CSDP, lch);
+
+	l = p->dma_read(CCR, lch);
+	l &= ~(0x03 << 12);
+	l |= src_amode << 12;
+	p->dma_write(l, CCR, lch);
+
+	p->dma_write(src_start, CSSA, lch);
+
+	p->dma_write(src_ei, CSEI, lch);
+	p->dma_write(src_fi, CSFI, lch);
+}
+EXPORT_SYMBOL(omap_set_dma_src_params);
+
+void omap_set_dma_src_data_pack(int lch, int enable)
+{
+	u32 l;
+
+	l = p->dma_read(CSDP, lch);
+	l &= ~(1 << 6);
+	if (enable)
+		l |= (1 << 6);
+	p->dma_write(l, CSDP, lch);
+}
+EXPORT_SYMBOL(omap_set_dma_src_data_pack);
+
+void omap_set_dma_src_burst_mode(int lch, enum omap_dma_burst_mode burst_mode)
+{
+	unsigned int burst = 0;
+	u32 l;
+
+	l = p->dma_read(CSDP, lch);
+	l &= ~(0x03 << 7);
+
+	switch (burst_mode) {
+	case OMAP_DMA_DATA_BURST_DIS:
+		break;
+	case OMAP_DMA_DATA_BURST_4:
+		burst = 0x2;
+		break;
+	case OMAP_DMA_DATA_BURST_8:
+		/*
+		 * not supported by current hardware on OMAP1
+		 * w |= (0x03 << 7);
+		 */
+		fallthrough;
+	case OMAP_DMA_DATA_BURST_16:
+		/* OMAP1 don't support burst 16 */
+		fallthrough;
+	default:
+		BUG();
+	}
+
+	l |= (burst << 7);
+	p->dma_write(l, CSDP, lch);
+}
+EXPORT_SYMBOL(omap_set_dma_src_burst_mode);
+
+/* Note that dest_port is only for OMAP1 */
+void omap_set_dma_dest_params(int lch, int dest_port, int dest_amode,
+			      unsigned long dest_start,
+			      int dst_ei, int dst_fi)
+{
+	u32 l;
+
+	l = p->dma_read(CSDP, lch);
+	l &= ~(0x1f << 9);
+	l |= dest_port << 9;
+	p->dma_write(l, CSDP, lch);
+
+	l = p->dma_read(CCR, lch);
+	l &= ~(0x03 << 14);
+	l |= dest_amode << 14;
+	p->dma_write(l, CCR, lch);
+
+	p->dma_write(dest_start, CDSA, lch);
+
+	p->dma_write(dst_ei, CDEI, lch);
+	p->dma_write(dst_fi, CDFI, lch);
+}
+EXPORT_SYMBOL(omap_set_dma_dest_params);
+
+void omap_set_dma_dest_data_pack(int lch, int enable)
+{
+	u32 l;
+
+	l = p->dma_read(CSDP, lch);
+	l &= ~(1 << 13);
+	if (enable)
+		l |= 1 << 13;
+	p->dma_write(l, CSDP, lch);
+}
+EXPORT_SYMBOL(omap_set_dma_dest_data_pack);
+
+void omap_set_dma_dest_burst_mode(int lch, enum omap_dma_burst_mode burst_mode)
+{
+	unsigned int burst = 0;
+	u32 l;
+
+	l = p->dma_read(CSDP, lch);
+	l &= ~(0x03 << 14);
+
+	switch (burst_mode) {
+	case OMAP_DMA_DATA_BURST_DIS:
+		break;
+	case OMAP_DMA_DATA_BURST_4:
+		burst = 0x2;
+		break;
+	case OMAP_DMA_DATA_BURST_8:
+		burst = 0x3;
+		break;
+	case OMAP_DMA_DATA_BURST_16:
+		/* OMAP1 don't support burst 16 */
+		fallthrough;
+	default:
+		printk(KERN_ERR "Invalid DMA burst mode\n");
+		BUG();
+		return;
+	}
+	l |= (burst << 14);
+	p->dma_write(l, CSDP, lch);
+}
+EXPORT_SYMBOL(omap_set_dma_dest_burst_mode);
+
+static inline void omap_enable_channel_irq(int lch)
+{
+	/* Clear CSR */
+	p->dma_read(CSR, lch);
+
+	/* Enable some nice interrupts. */
+	p->dma_write(dma_chan[lch].enabled_irqs, CICR, lch);
+}
+
+void omap_disable_dma_irq(int lch, u16 bits)
+{
+	dma_chan[lch].enabled_irqs &= ~bits;
+}
+EXPORT_SYMBOL(omap_disable_dma_irq);
+
+static inline void enable_lnk(int lch)
+{
+	u32 l;
+
+	l = p->dma_read(CLNK_CTRL, lch);
+
+	l &= ~(1 << 14);
+
+	/* Set the ENABLE_LNK bits */
+	if (dma_chan[lch].next_lch != -1)
+		l = dma_chan[lch].next_lch | (1 << 15);
+
+	p->dma_write(l, CLNK_CTRL, lch);
+}
+
+static inline void disable_lnk(int lch)
+{
+	u32 l;
+
+	l = p->dma_read(CLNK_CTRL, lch);
+
+	/* Disable interrupts */
+	omap_disable_channel_irq(lch);
+
+	/* Set the STOP_LNK bit */
+	l |= 1 << 14;
+
+	p->dma_write(l, CLNK_CTRL, lch);
+	dma_chan[lch].flags &= ~OMAP_DMA_ACTIVE;
+}
+#endif
+
+int omap_request_dma(int dev_id, const char *dev_name,
+		     void (*callback)(int lch, u16 ch_status, void *data),
+		     void *data, int *dma_ch_out)
+{
+	int ch, free_ch = -1;
+	unsigned long flags;
+	struct omap_dma_lch *chan;
+
+	WARN(strcmp(dev_name, "DMA engine"), "Using deprecated platform DMA API - please update to DMA engine");
+
+	spin_lock_irqsave(&dma_chan_lock, flags);
+	for (ch = 0; ch < dma_chan_count; ch++) {
+		if (free_ch == -1 && dma_chan[ch].dev_id == -1) {
+			free_ch = ch;
+			/* Exit after first free channel found */
+			break;
+		}
+	}
+	if (free_ch == -1) {
+		spin_unlock_irqrestore(&dma_chan_lock, flags);
+		return -EBUSY;
+	}
+	chan = dma_chan + free_ch;
+	chan->dev_id = dev_id;
+
+	if (p->clear_lch_regs)
+		p->clear_lch_regs(free_ch);
+
+	spin_unlock_irqrestore(&dma_chan_lock, flags);
+
+	chan->dev_name = dev_name;
+	chan->callback = callback;
+	chan->data = data;
+	chan->flags = 0;
+
+	chan->enabled_irqs = OMAP_DMA_DROP_IRQ | OMAP_DMA_BLOCK_IRQ;
+
+	chan->enabled_irqs |= OMAP1_DMA_TOUT_IRQ;
+
+	if (dma_omap16xx()) {
+		/* If the sync device is set, configure it dynamically. */
+		if (dev_id != 0) {
+			set_gdma_dev(free_ch + 1, dev_id);
+			dev_id = free_ch + 1;
+		}
+		/*
+		 * Disable the 1510 compatibility mode and set the sync device
+		 * id.
+		 */
+		p->dma_write(dev_id | (1 << 10), CCR, free_ch);
+	} else {
+		p->dma_write(dev_id, CCR, free_ch);
+	}
+
+	*dma_ch_out = free_ch;
+
+	return 0;
+}
+EXPORT_SYMBOL(omap_request_dma);
+
+void omap_free_dma(int lch)
+{
+	unsigned long flags;
+
+	if (dma_chan[lch].dev_id == -1) {
+		pr_err("omap_dma: trying to free unallocated DMA channel %d\n",
+		       lch);
+		return;
+	}
+
+	/* Disable all DMA interrupts for the channel. */
+	omap_disable_channel_irq(lch);
+
+	/* Make sure the DMA transfer is stopped. */
+	p->dma_write(0, CCR, lch);
+
+	spin_lock_irqsave(&dma_chan_lock, flags);
+	dma_chan[lch].dev_id = -1;
+	dma_chan[lch].next_lch = -1;
+	dma_chan[lch].callback = NULL;
+	spin_unlock_irqrestore(&dma_chan_lock, flags);
+}
+EXPORT_SYMBOL(omap_free_dma);
+
+/*
+ * Clears any DMA state so the DMA engine is ready to restart with new buffers
+ * through omap_start_dma(). Any buffers in flight are discarded.
+ */
+static void omap_clear_dma(int lch)
+{
+	unsigned long flags;
+
+	local_irq_save(flags);
+	p->clear_dma(lch);
+	local_irq_restore(flags);
+}
+
+#if IS_ENABLED(CONFIG_USB_OMAP)
+void omap_start_dma(int lch)
+{
+	u32 l;
+
+	/*
+	 * The CPC/CDAC register needs to be initialized to zero
+	 * before starting dma transfer.
+	 */
+	if (dma_omap15xx())
+		p->dma_write(0, CPC, lch);
+	else
+		p->dma_write(0, CDAC, lch);
+
+	if (!omap_dma_in_1510_mode() && dma_chan[lch].next_lch != -1) {
+		int next_lch, cur_lch;
+		char dma_chan_link_map[MAX_LOGICAL_DMA_CH_COUNT];
+
+		/* Set the link register of the first channel */
+		enable_lnk(lch);
+
+		memset(dma_chan_link_map, 0, sizeof(dma_chan_link_map));
+		dma_chan_link_map[lch] = 1;
+
+		cur_lch = dma_chan[lch].next_lch;
+		do {
+			next_lch = dma_chan[cur_lch].next_lch;
+
+			/* The loop case: we've been here already */
+			if (dma_chan_link_map[cur_lch])
+				break;
+			/* Mark the current channel */
+			dma_chan_link_map[cur_lch] = 1;
+
+			enable_lnk(cur_lch);
+			omap_enable_channel_irq(cur_lch);
+
+			cur_lch = next_lch;
+		} while (next_lch != -1);
+	} else if (IS_DMA_ERRATA(DMA_ERRATA_PARALLEL_CHANNELS))
+		p->dma_write(lch, CLNK_CTRL, lch);
+
+	omap_enable_channel_irq(lch);
+
+	l = p->dma_read(CCR, lch);
+
+	if (IS_DMA_ERRATA(DMA_ERRATA_IFRAME_BUFFERING))
+			l |= OMAP_DMA_CCR_BUFFERING_DISABLE;
+	l |= OMAP_DMA_CCR_EN;
+
+	/*
+	 * As dma_write() uses IO accessors which are weakly ordered, there
+	 * is no guarantee that data in coherent DMA memory will be visible
+	 * to the DMA device.  Add a memory barrier here to ensure that any
+	 * such data is visible prior to enabling DMA.
+	 */
+	mb();
+	p->dma_write(l, CCR, lch);
+
+	dma_chan[lch].flags |= OMAP_DMA_ACTIVE;
+}
+EXPORT_SYMBOL(omap_start_dma);
+
+void omap_stop_dma(int lch)
+{
+	u32 l;
+
+	/* Disable all interrupts on the channel */
+	omap_disable_channel_irq(lch);
+
+	l = p->dma_read(CCR, lch);
+	if (IS_DMA_ERRATA(DMA_ERRATA_i541) &&
+			(l & OMAP_DMA_CCR_SEL_SRC_DST_SYNC)) {
+		int i = 0;
+		u32 sys_cf;
+
+		/* Configure No-Standby */
+		l = p->dma_read(OCP_SYSCONFIG, lch);
+		sys_cf = l;
+		l &= ~DMA_SYSCONFIG_MIDLEMODE_MASK;
+		l |= DMA_SYSCONFIG_MIDLEMODE(DMA_IDLEMODE_NO_IDLE);
+		p->dma_write(l , OCP_SYSCONFIG, 0);
+
+		l = p->dma_read(CCR, lch);
+		l &= ~OMAP_DMA_CCR_EN;
+		p->dma_write(l, CCR, lch);
+
+		/* Wait for sDMA FIFO drain */
+		l = p->dma_read(CCR, lch);
+		while (i < 100 && (l & (OMAP_DMA_CCR_RD_ACTIVE |
+					OMAP_DMA_CCR_WR_ACTIVE))) {
+			udelay(5);
+			i++;
+			l = p->dma_read(CCR, lch);
+		}
+		if (i >= 100)
+			pr_err("DMA drain did not complete on lch %d\n", lch);
+		/* Restore OCP_SYSCONFIG */
+		p->dma_write(sys_cf, OCP_SYSCONFIG, lch);
+	} else {
+		l &= ~OMAP_DMA_CCR_EN;
+		p->dma_write(l, CCR, lch);
+	}
+
+	/*
+	 * Ensure that data transferred by DMA is visible to any access
+	 * after DMA has been disabled.  This is important for coherent
+	 * DMA regions.
+	 */
+	mb();
+
+	if (!omap_dma_in_1510_mode() && dma_chan[lch].next_lch != -1) {
+		int next_lch, cur_lch = lch;
+		char dma_chan_link_map[MAX_LOGICAL_DMA_CH_COUNT];
+
+		memset(dma_chan_link_map, 0, sizeof(dma_chan_link_map));
+		do {
+			/* The loop case: we've been here already */
+			if (dma_chan_link_map[cur_lch])
+				break;
+			/* Mark the current channel */
+			dma_chan_link_map[cur_lch] = 1;
+
+			disable_lnk(cur_lch);
+
+			next_lch = dma_chan[cur_lch].next_lch;
+			cur_lch = next_lch;
+		} while (next_lch != -1);
+	}
+
+	dma_chan[lch].flags &= ~OMAP_DMA_ACTIVE;
+}
+EXPORT_SYMBOL(omap_stop_dma);
+
+/*
+ * Allows changing the DMA callback function or data. This may be needed if
+ * the driver shares a single DMA channel for multiple dma triggers.
+ */
+/*
+ * Returns current physical source address for the given DMA channel.
+ * If the channel is running the caller must disable interrupts prior calling
+ * this function and process the returned value before re-enabling interrupt to
+ * prevent races with the interrupt handler. Note that in continuous mode there
+ * is a chance for CSSA_L register overflow between the two reads resulting
+ * in incorrect return value.
+ */
+dma_addr_t omap_get_dma_src_pos(int lch)
+{
+	dma_addr_t offset = 0;
+
+	if (dma_omap15xx())
+		offset = p->dma_read(CPC, lch);
+	else
+		offset = p->dma_read(CSAC, lch);
+
+	if (IS_DMA_ERRATA(DMA_ERRATA_3_3) && offset == 0)
+		offset = p->dma_read(CSAC, lch);
+
+	if (!dma_omap15xx()) {
+		/*
+		 * CDAC == 0 indicates that the DMA transfer on the channel has
+		 * not been started (no data has been transferred so far).
+		 * Return the programmed source start address in this case.
+		 */
+		if (likely(p->dma_read(CDAC, lch)))
+			offset = p->dma_read(CSAC, lch);
+		else
+			offset = p->dma_read(CSSA, lch);
+	}
+
+	offset |= (p->dma_read(CSSA, lch) & 0xFFFF0000);
+
+	return offset;
+}
+EXPORT_SYMBOL(omap_get_dma_src_pos);
+
+/*
+ * Returns current physical destination address for the given DMA channel.
+ * If the channel is running the caller must disable interrupts prior calling
+ * this function and process the returned value before re-enabling interrupt to
+ * prevent races with the interrupt handler. Note that in continuous mode there
+ * is a chance for CDSA_L register overflow between the two reads resulting
+ * in incorrect return value.
+ */
+dma_addr_t omap_get_dma_dst_pos(int lch)
+{
+	dma_addr_t offset = 0;
+
+	if (dma_omap15xx())
+		offset = p->dma_read(CPC, lch);
+	else
+		offset = p->dma_read(CDAC, lch);
+
+	/*
+	 * omap 3.2/3.3 erratum: sometimes 0 is returned if CSAC/CDAC is
+	 * read before the DMA controller finished disabling the channel.
+	 */
+	if (!dma_omap15xx() && offset == 0) {
+		offset = p->dma_read(CDAC, lch);
+		/*
+		 * CDAC == 0 indicates that the DMA transfer on the channel has
+		 * not been started (no data has been transferred so far).
+		 * Return the programmed destination start address in this case.
+		 */
+		if (unlikely(!offset))
+			offset = p->dma_read(CDSA, lch);
+	}
+
+	offset |= (p->dma_read(CDSA, lch) & 0xFFFF0000);
+
+	return offset;
+}
+EXPORT_SYMBOL(omap_get_dma_dst_pos);
+
+int omap_get_dma_active_status(int lch)
+{
+	return (p->dma_read(CCR, lch) & OMAP_DMA_CCR_EN) != 0;
+}
+EXPORT_SYMBOL(omap_get_dma_active_status);
+#endif
+
+int omap_dma_running(void)
+{
+	int lch;
+
+	if (omap_lcd_dma_running())
+		return 1;
+
+	for (lch = 0; lch < dma_chan_count; lch++)
+		if (p->dma_read(CCR, lch) & OMAP_DMA_CCR_EN)
+			return 1;
+
+	return 0;
+}
+
+/*----------------------------------------------------------------------------*/
+
+static int omap1_dma_handle_ch(int ch)
+{
+	u32 csr;
+
+	if (enable_1510_mode && ch >= 6) {
+		csr = dma_chan[ch].saved_csr;
+		dma_chan[ch].saved_csr = 0;
+	} else
+		csr = p->dma_read(CSR, ch);
+	if (enable_1510_mode && ch <= 2 && (csr >> 7) != 0) {
+		dma_chan[ch + 6].saved_csr = csr >> 7;
+		csr &= 0x7f;
+	}
+	if ((csr & 0x3f) == 0)
+		return 0;
+	if (unlikely(dma_chan[ch].dev_id == -1)) {
+		pr_warn("Spurious interrupt from DMA channel %d (CSR %04x)\n",
+			ch, csr);
+		return 0;
+	}
+	if (unlikely(csr & OMAP1_DMA_TOUT_IRQ))
+		pr_warn("DMA timeout with device %d\n", dma_chan[ch].dev_id);
+	if (unlikely(csr & OMAP_DMA_DROP_IRQ))
+		pr_warn("DMA synchronization event drop occurred with device %d\n",
+			dma_chan[ch].dev_id);
+	if (likely(csr & OMAP_DMA_BLOCK_IRQ))
+		dma_chan[ch].flags &= ~OMAP_DMA_ACTIVE;
+	if (likely(dma_chan[ch].callback != NULL))
+		dma_chan[ch].callback(ch, csr, dma_chan[ch].data);
+
+	return 1;
+}
+
+static irqreturn_t omap1_dma_irq_handler(int irq, void *dev_id)
+{
+	int ch = ((int) dev_id) - 1;
+	int handled = 0;
+
+	for (;;) {
+		int handled_now = 0;
+
+		handled_now += omap1_dma_handle_ch(ch);
+		if (enable_1510_mode && dma_chan[ch + 6].saved_csr)
+			handled_now += omap1_dma_handle_ch(ch + 6);
+		if (!handled_now)
+			break;
+		handled += handled_now;
+	}
+
+	return handled ? IRQ_HANDLED : IRQ_NONE;
+}
+
+struct omap_system_dma_plat_info *omap_get_plat_info(void)
+{
+	return p;
+}
+EXPORT_SYMBOL_GPL(omap_get_plat_info);
+
+static int omap_system_dma_probe(struct platform_device *pdev)
+{
+	int ch, ret = 0;
+	int dma_irq;
+	char irq_name[4];
+
+	p = pdev->dev.platform_data;
+	if (!p) {
+		dev_err(&pdev->dev,
+			"%s: System DMA initialized without platform data\n",
+			__func__);
+		return -EINVAL;
+	}
+
+	d			= p->dma_attr;
+	errata			= p->errata;
+
+	if ((d->dev_caps & RESERVE_CHANNEL) && omap_dma_reserve_channels
+			&& (omap_dma_reserve_channels < d->lch_count))
+		d->lch_count	= omap_dma_reserve_channels;
+
+	dma_lch_count		= d->lch_count;
+	dma_chan_count		= dma_lch_count;
+	enable_1510_mode	= d->dev_caps & ENABLE_1510_MODE;
+
+	dma_chan = devm_kcalloc(&pdev->dev, dma_lch_count,
+				sizeof(*dma_chan), GFP_KERNEL);
+	if (!dma_chan)
+		return -ENOMEM;
+
+	for (ch = 0; ch < dma_chan_count; ch++) {
+		omap_clear_dma(ch);
+
+		dma_chan[ch].dev_id = -1;
+		dma_chan[ch].next_lch = -1;
+
+		if (ch >= 6 && enable_1510_mode)
+			continue;
+
+		/*
+		 * request_irq() doesn't like dev_id (ie. ch) being
+		 * zero, so we have to kludge around this.
+		 */
+		sprintf(&irq_name[0], "%d", ch);
+		dma_irq = platform_get_irq_byname(pdev, irq_name);
+
+		if (dma_irq < 0) {
+			ret = dma_irq;
+			goto exit_dma_irq_fail;
+		}
+
+		/* INT_DMA_LCD is handled in lcd_dma.c */
+		if (dma_irq == INT_DMA_LCD)
+			continue;
+
+		ret = request_irq(dma_irq,
+				omap1_dma_irq_handler, 0, "DMA",
+				(void *) (ch + 1));
+		if (ret != 0)
+			goto exit_dma_irq_fail;
+	}
+
+	/* reserve dma channels 0 and 1 in high security devices on 34xx */
+	if (d->dev_caps & HS_CHANNELS_RESERVED) {
+		pr_info("Reserving DMA channels 0 and 1 for HS ROM code\n");
+		dma_chan[0].dev_id = 0;
+		dma_chan[1].dev_id = 1;
+	}
+	p->show_dma_caps();
+	return 0;
+
+exit_dma_irq_fail:
+	return ret;
+}
+
+static int omap_system_dma_remove(struct platform_device *pdev)
+{
+	int dma_irq, irq_rel = 0;
+
+	for ( ; irq_rel < dma_chan_count; irq_rel++) {
+		dma_irq = platform_get_irq(pdev, irq_rel);
+		free_irq(dma_irq, (void *)(irq_rel + 1));
+	}
+
+	return 0;
+}
+
+static struct platform_driver omap_system_dma_driver = {
+	.probe		= omap_system_dma_probe,
+	.remove		= omap_system_dma_remove,
+	.driver		= {
+		.name	= "omap_dma_system"
+	},
+};
+
+static int __init omap_system_dma_init(void)
+{
+	return platform_driver_register(&omap_system_dma_driver);
+}
+arch_initcall(omap_system_dma_init);
+
+static void __exit omap_system_dma_exit(void)
+{
+	platform_driver_unregister(&omap_system_dma_driver);
+}
+
+MODULE_DESCRIPTION("OMAP SYSTEM DMA DRIVER");
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Texas Instruments Inc");
+
+/*
+ * Reserve the omap SDMA channels using cmdline bootarg
+ * "omap_dma_reserve_ch=". The valid range is 1 to 32
+ */
+static int __init omap_dma_cmdline_reserve_ch(char *str)
+{
+	if (get_option(&str, &omap_dma_reserve_channels) != 1)
+		omap_dma_reserve_channels = 0;
+	return 1;
+}
+
+__setup("omap_dma_reserve_ch=", omap_dma_cmdline_reserve_ch);
+
+
diff --git a/arch/arm/mach-omap1/include/mach/omap1510.h b/arch/arm/mach-omap1/omap1510.h
index 3d235244bf5c..3d235244bf5c 100644
--- a/arch/arm/mach-omap1/include/mach/omap1510.h
+++ b/arch/arm/mach-omap1/omap1510.h
diff --git a/arch/arm/mach-omap1/include/mach/omap16xx.h b/arch/arm/mach-omap1/omap16xx.h
index cd1c724869c7..cd1c724869c7 100644
--- a/arch/arm/mach-omap1/include/mach/omap16xx.h
+++ b/arch/arm/mach-omap1/omap16xx.h
diff --git a/arch/arm/mach-omap1/include/mach/omap7xx.h b/arch/arm/mach-omap1/omap7xx.h
index 63da994bc609..63da994bc609 100644
--- a/arch/arm/mach-omap1/include/mach/omap7xx.h
+++ b/arch/arm/mach-omap1/omap7xx.h
diff --git a/arch/arm/mach-omap1/pm.c b/arch/arm/mach-omap1/pm.c
index a745d64d4699..fce7d2b572bf 100644
--- a/arch/arm/mach-omap1/pm.c
+++ b/arch/arm/mach-omap1/pm.c
@@ -52,13 +52,14 @@
 #include <asm/mach/time.h>
 #include <asm/mach/irq.h>
 
-#include <mach/tc.h>
-#include <mach/mux.h>
+#include <linux/soc/ti/omap1-io.h>
+#include "tc.h"
 #include <linux/omap-dma.h>
 #include <clocksource/timer-ti-dm.h>
 
-#include <mach/irqs.h>
-
+#include "hardware.h"
+#include "mux.h"
+#include "irqs.h"
 #include "iomap.h"
 #include "clock.h"
 #include "pm.h"
diff --git a/arch/arm/mach-omap1/pm.h b/arch/arm/mach-omap1/pm.h
index cd926dcb5e7f..d9165709c532 100644
--- a/arch/arm/mach-omap1/pm.h
+++ b/arch/arm/mach-omap1/pm.h
@@ -34,6 +34,8 @@
 #ifndef __ARCH_ARM_MACH_OMAP1_PM_H
 #define __ARCH_ARM_MACH_OMAP1_PM_H
 
+#include <linux/soc/ti/omap1-io.h>
+
 /*
  * ----------------------------------------------------------------------------
  * Register and offset definitions to be used in PM assembler code
diff --git a/arch/arm/mach-omap1/pm_bus.c b/arch/arm/mach-omap1/pm_bus.c
index 667c1637ff91..c04619ac0631 100644
--- a/arch/arm/mach-omap1/pm_bus.c
+++ b/arch/arm/mach-omap1/pm_bus.c
@@ -1,13 +1,10 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Runtime PM support code for OMAP1
  *
  * Author: Kevin Hilman, Deep Root Systems, LLC
  *
  * Copyright (C) 2010 Texas Instruments, Inc.
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 #include <linux/init.h>
 #include <linux/kernel.h>
@@ -43,4 +40,3 @@ static int __init omap1_pm_runtime_init(void)
 	return 0;
 }
 core_initcall(omap1_pm_runtime_init);
-
diff --git a/arch/arm/mach-omap1/reset.c b/arch/arm/mach-omap1/reset.c
index af2c120b0c4e..2eee6a6965ff 100644
--- a/arch/arm/mach-omap1/reset.c
+++ b/arch/arm/mach-omap1/reset.c
@@ -6,8 +6,7 @@
 #include <linux/io.h>
 #include <linux/reboot.h>
 
-#include <mach/hardware.h>
-
+#include "hardware.h"
 #include "iomap.h"
 #include "common.h"
 
diff --git a/arch/arm/mach-omap1/serial.c b/arch/arm/mach-omap1/serial.c
index 9eb591fbfd89..88928fc33b2e 100644
--- a/arch/arm/mach-omap1/serial.c
+++ b/arch/arm/mach-omap1/serial.c
@@ -19,8 +19,8 @@
 
 #include <asm/mach-types.h>
 
-#include <mach/mux.h>
-
+#include "serial.h"
+#include "mux.h"
 #include "pm.h"
 #include "soc.h"
 
@@ -141,7 +141,7 @@ void __init omap_serial_init(void)
 			if (IS_ERR(uart1_ck))
 				printk("Could not get uart1_ck\n");
 			else {
-				clk_enable(uart1_ck);
+				clk_prepare_enable(uart1_ck);
 				if (cpu_is_omap15xx())
 					clk_set_rate(uart1_ck, 12000000);
 			}
@@ -151,7 +151,7 @@ void __init omap_serial_init(void)
 			if (IS_ERR(uart2_ck))
 				printk("Could not get uart2_ck\n");
 			else {
-				clk_enable(uart2_ck);
+				clk_prepare_enable(uart2_ck);
 				if (cpu_is_omap15xx())
 					clk_set_rate(uart2_ck, 12000000);
 				else
@@ -163,7 +163,7 @@ void __init omap_serial_init(void)
 			if (IS_ERR(uart3_ck))
 				printk("Could not get uart3_ck\n");
 			else {
-				clk_enable(uart3_ck);
+				clk_prepare_enable(uart3_ck);
 				if (cpu_is_omap15xx())
 					clk_set_rate(uart3_ck, 12000000);
 			}
diff --git a/arch/arm/mach-omap1/include/mach/serial.h b/arch/arm/mach-omap1/serial.h
index 4700e384c3d9..4700e384c3d9 100644
--- a/arch/arm/mach-omap1/include/mach/serial.h
+++ b/arch/arm/mach-omap1/serial.h
diff --git a/arch/arm/mach-omap1/sleep.S b/arch/arm/mach-omap1/sleep.S
index a908c51839a4..f111b79512ce 100644
--- a/arch/arm/mach-omap1/sleep.S
+++ b/arch/arm/mach-omap1/sleep.S
@@ -36,7 +36,7 @@
 
 #include <asm/assembler.h>
 
-#include <mach/hardware.h>
+#include "hardware.h"
 
 #include "iomap.h"
 #include "pm.h"
diff --git a/arch/arm/mach-omap1/soc.h b/arch/arm/mach-omap1/soc.h
index 69daf0187b1d..5fb57fdd9c2b 100644
--- a/arch/arm/mach-omap1/soc.h
+++ b/arch/arm/mach-omap1/soc.h
@@ -1,4 +1,6 @@
 /*
- * We can move mach/soc.h here once the drivers are fixed
+ * We can move linux/soc/ti/omap1-soc.h here once the drivers are fixed
  */
-#include <mach/soc.h>
+#include "hardware.h"
+#include "irqs.h"
+#include <asm/irq.h>
diff --git a/arch/arm/mach-omap1/sram-init.c b/arch/arm/mach-omap1/sram-init.c
index 3bd60708c345..27c42e2a21cc 100644
--- a/arch/arm/mach-omap1/sram-init.c
+++ b/arch/arm/mach-omap1/sram-init.c
@@ -14,6 +14,7 @@
 #include <asm/fncpy.h>
 #include <asm/tlb.h>
 #include <asm/cacheflush.h>
+#include <asm/set_memory.h>
 
 #include <asm/mach/map.h>
 
@@ -22,18 +23,77 @@
 
 #define OMAP1_SRAM_PA		0x20000000
 #define SRAM_BOOTLOADER_SZ	0x80
+#define ROUND_DOWN(value,boundary)	((value) & (~((boundary)-1)))
+
+static void __iomem *omap_sram_base;
+static unsigned long omap_sram_start;
+static unsigned long omap_sram_skip;
+static unsigned long omap_sram_size;
+static void __iomem *omap_sram_ceil;
+
+/*
+ * Memory allocator for SRAM: calculates the new ceiling address
+ * for pushing a function using the fncpy API.
+ *
+ * Note that fncpy requires the returned address to be aligned
+ * to an 8-byte boundary.
+ */
+static void *omap_sram_push_address(unsigned long size)
+{
+	unsigned long available, new_ceil = (unsigned long)omap_sram_ceil;
+
+	available = omap_sram_ceil - (omap_sram_base + omap_sram_skip);
+
+	if (size > available) {
+		pr_err("Not enough space in SRAM\n");
+		return NULL;
+	}
+
+	new_ceil -= size;
+	new_ceil = ROUND_DOWN(new_ceil, FNCPY_ALIGN);
+	omap_sram_ceil = IOMEM(new_ceil);
+
+	return (void __force *)omap_sram_ceil;
+}
+
+void *omap_sram_push(void *funcp, unsigned long size)
+{
+	void *sram;
+	unsigned long base;
+	int pages;
+	void *dst = NULL;
+
+	sram = omap_sram_push_address(size);
+	if (!sram)
+		return NULL;
+
+	base = (unsigned long)sram & PAGE_MASK;
+	pages = PAGE_ALIGN(size) / PAGE_SIZE;
+
+	set_memory_rw(base, pages);
+
+	dst = fncpy(sram, funcp, size);
+
+	set_memory_ro(base, pages);
+	set_memory_x(base, pages);
+
+	return dst;
+}
 
 /*
  * The amount of SRAM depends on the core type.
  * Note that we cannot try to test for SRAM here because writes
  * to secure SRAM will hang the system. Also the SRAM is not
  * yet mapped at this point.
+ * Note that we cannot use ioremap for SRAM, as clock init needs SRAM early.
  */
 static void __init omap_detect_and_map_sram(void)
 {
-	unsigned long omap_sram_skip = SRAM_BOOTLOADER_SZ;
-	unsigned long omap_sram_start = OMAP1_SRAM_PA;
-	unsigned long omap_sram_size;
+	unsigned long base;
+	int pages;
+
+	omap_sram_skip = SRAM_BOOTLOADER_SZ;
+	omap_sram_start = OMAP1_SRAM_PA;
 
 	if (cpu_is_omap7xx())
 		omap_sram_size = 0x32000;	/* 200K */
@@ -47,8 +107,27 @@ static void __init omap_detect_and_map_sram(void)
 		omap_sram_size = 0x4000;
 	}
 
-	omap_map_sram(omap_sram_start, omap_sram_size,
-		omap_sram_skip, 1);
+	omap_sram_start = ROUND_DOWN(omap_sram_start, PAGE_SIZE);
+	omap_sram_base = __arm_ioremap_exec(omap_sram_start, omap_sram_size, 1);
+	if (!omap_sram_base) {
+		pr_err("SRAM: Could not map\n");
+		return;
+	}
+
+	omap_sram_ceil = omap_sram_base + omap_sram_size;
+
+	/*
+	 * Looks like we need to preserve some bootloader code at the
+	 * beginning of SRAM for jumping to flash for reboot to work...
+	 */
+	memset_io(omap_sram_base + omap_sram_skip, 0,
+		  omap_sram_size - omap_sram_skip);
+
+	base = (unsigned long)omap_sram_base;
+	pages = PAGE_ALIGN(omap_sram_size) / PAGE_SIZE;
+
+	set_memory_ro(base, pages);
+	set_memory_x(base, pages);
 }
 
 static void (*_omap_sram_reprogram_clock)(u32 dpllctl, u32 ckctl);
@@ -62,7 +141,7 @@ void omap_sram_reprogram_clock(u32 dpllctl, u32 ckctl)
 	_omap_sram_reprogram_clock(dpllctl, ckctl);
 }
 
-int __init omap_sram_init(void)
+int __init omap1_sram_init(void)
 {
 	omap_detect_and_map_sram();
 	_omap_sram_reprogram_clock =
diff --git a/arch/arm/mach-omap1/sram.S b/arch/arm/mach-omap1/sram.S
index 37f34fcd65fb..89f4dc1b70f0 100644
--- a/arch/arm/mach-omap1/sram.S
+++ b/arch/arm/mach-omap1/sram.S
@@ -6,11 +6,11 @@
  */
 
 #include <linux/linkage.h>
+#include <linux/soc/ti/omap1-io.h>
 
 #include <asm/assembler.h>
 
-#include <mach/hardware.h>
-
+#include "hardware.h"
 #include "iomap.h"
 
 	.text
diff --git a/arch/arm/mach-omap1/sram.h b/arch/arm/mach-omap1/sram.h
index 73efabd119e8..f45e6dd6d7e5 100644
--- a/arch/arm/mach-omap1/sram.h
+++ b/arch/arm/mach-omap1/sram.h
@@ -1,8 +1,10 @@
 /* SPDX-License-Identifier: GPL-2.0 */
-#include <plat/sram.h>
 
 extern void omap_sram_reprogram_clock(u32 dpllctl, u32 ckctl);
 
+int omap1_sram_init(void);
+void *omap_sram_push(void *funcp, unsigned long size);
+
 /* Do not use these */
 extern void omap1_sram_reprogram_clock(u32 ckctl, u32 dpllctl);
 extern unsigned long omap1_sram_reprogram_clock_sz;
diff --git a/arch/arm/mach-omap1/tc.h b/arch/arm/mach-omap1/tc.h
new file mode 100644
index 000000000000..243454bc0684
--- /dev/null
+++ b/arch/arm/mach-omap1/tc.h
@@ -0,0 +1,74 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * OMAP Traffic Controller
+ *
+ * Copyright (C) 2004 Nokia Corporation
+ * Author: Imre Deak <imre.deak@nokia.com>
+ */
+
+#ifndef __ASM_ARCH_TC_H
+#define __ASM_ARCH_TC_H
+
+#define TCMIF_BASE		0xfffecc00
+#define OMAP_TC_OCPT1_PRIOR	(TCMIF_BASE + 0x00)
+#define OMAP_TC_EMIFS_PRIOR	(TCMIF_BASE + 0x04)
+#define OMAP_TC_EMIFF_PRIOR	(TCMIF_BASE + 0x08)
+#define EMIFS_CONFIG		(TCMIF_BASE + 0x0c)
+#define EMIFS_CS0_CONFIG	(TCMIF_BASE + 0x10)
+#define EMIFS_CS1_CONFIG	(TCMIF_BASE + 0x14)
+#define EMIFS_CS2_CONFIG	(TCMIF_BASE + 0x18)
+#define EMIFS_CS3_CONFIG	(TCMIF_BASE + 0x1c)
+#define EMIFF_SDRAM_CONFIG	(TCMIF_BASE + 0x20)
+#define EMIFF_MRS		(TCMIF_BASE + 0x24)
+#define TC_TIMEOUT1		(TCMIF_BASE + 0x28)
+#define TC_TIMEOUT2		(TCMIF_BASE + 0x2c)
+#define TC_TIMEOUT3		(TCMIF_BASE + 0x30)
+#define TC_ENDIANISM		(TCMIF_BASE + 0x34)
+#define EMIFF_SDRAM_CONFIG_2	(TCMIF_BASE + 0x3c)
+#define EMIF_CFG_DYNAMIC_WS	(TCMIF_BASE + 0x40)
+#define EMIFS_ACS0		(TCMIF_BASE + 0x50)
+#define EMIFS_ACS1		(TCMIF_BASE + 0x54)
+#define EMIFS_ACS2		(TCMIF_BASE + 0x58)
+#define EMIFS_ACS3		(TCMIF_BASE + 0x5c)
+#define OMAP_TC_OCPT2_PRIOR	(TCMIF_BASE + 0xd0)
+
+/* external EMIFS chipselect regions */
+#define	OMAP_CS0_PHYS		0x00000000
+#define	OMAP_CS0_SIZE		SZ_64M
+
+#define	OMAP_CS1_PHYS		0x04000000
+#define	OMAP_CS1_SIZE		SZ_64M
+
+#define	OMAP_CS1A_PHYS		OMAP_CS1_PHYS
+#define	OMAP_CS1A_SIZE		SZ_32M
+
+#define	OMAP_CS1B_PHYS		(OMAP_CS1A_PHYS + OMAP_CS1A_SIZE)
+#define	OMAP_CS1B_SIZE		SZ_32M
+
+#define	OMAP_CS2_PHYS		0x08000000
+#define	OMAP_CS2_SIZE		SZ_64M
+
+#define	OMAP_CS2A_PHYS		OMAP_CS2_PHYS
+#define	OMAP_CS2A_SIZE		SZ_32M
+
+#define	OMAP_CS2B_PHYS		(OMAP_CS2A_PHYS + OMAP_CS2A_SIZE)
+#define	OMAP_CS2B_SIZE		SZ_32M
+
+#define	OMAP_CS3_PHYS		0x0c000000
+#define	OMAP_CS3_SIZE		SZ_64M
+
+#ifndef	__ASSEMBLER__
+
+/* EMIF Slow Interface Configuration Register */
+#define OMAP_EMIFS_CONFIG_FR		(1 << 4)
+#define OMAP_EMIFS_CONFIG_PDE		(1 << 3)
+#define OMAP_EMIFS_CONFIG_PWD_EN	(1 << 2)
+#define OMAP_EMIFS_CONFIG_BM		(1 << 1)
+#define OMAP_EMIFS_CONFIG_WP		(1 << 0)
+
+#define EMIFS_CCS(n)		(EMIFS_CS0_CONFIG + (4 * (n)))
+#define EMIFS_ACS(n)		(EMIFS_ACS0 + (4 * (n)))
+
+#endif	/* __ASSEMBLER__ */
+
+#endif	/* __ASM_ARCH_TC_H */
diff --git a/arch/arm/mach-omap1/time.c b/arch/arm/mach-omap1/time.c
index de590a85a42b..d5e127851dc7 100644
--- a/arch/arm/mach-omap1/time.c
+++ b/arch/arm/mach-omap1/time.c
@@ -47,12 +47,14 @@
 
 #include <asm/irq.h>
 
-#include <mach/hardware.h>
 #include <asm/mach/irq.h>
 #include <asm/mach/time.h>
 
+#include "hardware.h"
+#include "mux.h"
 #include "iomap.h"
 #include "common.h"
+#include "clock.h"
 
 #ifdef CONFIG_OMAP_MPU_TIMER
 
@@ -224,6 +226,9 @@ static inline void omap_mpu_timer_init(void)
  */
 void __init omap1_timer_init(void)
 {
+	omap1_clk_init();
+	omap1_mux_init();
+
 	if (omap_32k_timer_init() != 0)
 		omap_mpu_timer_init();
 }
diff --git a/arch/arm/mach-omap1/timer.c b/arch/arm/mach-omap1/timer.c
index 0411d5508d63..f5cd4bbf7566 100644
--- a/arch/arm/mach-omap1/timer.c
+++ b/arch/arm/mach-omap1/timer.c
@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * OMAP1 Dual-Mode Timers - platform device registration
  *
@@ -9,15 +10,6 @@
  * Copyright (C) 2011 Texas Instruments Incorporated - https://www.ti.com/
  * Tarun Kanti DebBarma <tarun.kanti@ti.com>
  * Thara Gopinath <thara@ti.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- * This program is distributed "as is" WITHOUT ANY WARRANTY of any
- * kind, whether express or implied; without even the implied warranty
- * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
  */
 
 #include <linux/clk.h>
@@ -26,6 +18,7 @@
 #include <linux/slab.h>
 #include <linux/platform_device.h>
 #include <linux/platform_data/dmtimer-omap.h>
+#include <linux/soc/ti/omap1-io.h>
 
 #include <clocksource/timer-ti-dm.h>
 
diff --git a/arch/arm/mach-omap1/timer32k.c b/arch/arm/mach-omap1/timer32k.c
index 780fdf03c3ce..410d17d1d443 100644
--- a/arch/arm/mach-omap1/timer32k.c
+++ b/arch/arm/mach-omap1/timer32k.c
@@ -45,15 +45,13 @@
 #include <linux/clocksource.h>
 #include <linux/clockchips.h>
 #include <linux/io.h>
+#include <linux/sched_clock.h>
 
 #include <asm/irq.h>
 #include <asm/mach/irq.h>
 #include <asm/mach/time.h>
 
-#include <plat/counter-32k.h>
-
-#include <mach/hardware.h>
-
+#include "hardware.h"
 #include "common.h"
 
 /*
@@ -159,6 +157,98 @@ static __init void omap_init_32k_timer(void)
 					OMAP_32K_TICKS_PER_SEC, 1, 0xfffffffe);
 }
 
+/* OMAP2_32KSYNCNT_CR_OFF: offset of 32ksync counter register */
+#define OMAP2_32KSYNCNT_REV_OFF		0x0
+#define OMAP2_32KSYNCNT_REV_SCHEME	(0x3 << 30)
+#define OMAP2_32KSYNCNT_CR_OFF_LOW	0x10
+#define OMAP2_32KSYNCNT_CR_OFF_HIGH	0x30
+
+/*
+ * 32KHz clocksource ... always available, on pretty most chips except
+ * OMAP 730 and 1510.  Other timers could be used as clocksources, with
+ * higher resolution in free-running counter modes (e.g. 12 MHz xtal),
+ * but systems won't necessarily want to spend resources that way.
+ */
+static void __iomem *sync32k_cnt_reg;
+
+static u64 notrace omap_32k_read_sched_clock(void)
+{
+	return sync32k_cnt_reg ? readl_relaxed(sync32k_cnt_reg) : 0;
+}
+
+/**
+ * omap_read_persistent_clock64 -  Return time from a persistent clock.
+ *
+ * Reads the time from a source which isn't disabled during PM, the
+ * 32k sync timer.  Convert the cycles elapsed since last read into
+ * nsecs and adds to a monotonically increasing timespec64.
+ */
+static struct timespec64 persistent_ts;
+static cycles_t cycles;
+static unsigned int persistent_mult, persistent_shift;
+
+static void omap_read_persistent_clock64(struct timespec64 *ts)
+{
+	unsigned long long nsecs;
+	cycles_t last_cycles;
+
+	last_cycles = cycles;
+	cycles = sync32k_cnt_reg ? readl_relaxed(sync32k_cnt_reg) : 0;
+
+	nsecs = clocksource_cyc2ns(cycles - last_cycles,
+					persistent_mult, persistent_shift);
+
+	timespec64_add_ns(&persistent_ts, nsecs);
+
+	*ts = persistent_ts;
+}
+
+/**
+ * omap_init_clocksource_32k - setup and register counter 32k as a
+ * kernel clocksource
+ * @pbase: base addr of counter_32k module
+ * @size: size of counter_32k to map
+ *
+ * Returns 0 upon success or negative error code upon failure.
+ *
+ */
+static int __init omap_init_clocksource_32k(void __iomem *vbase)
+{
+	int ret;
+
+	/*
+	 * 32k sync Counter IP register offsets vary between the
+	 * highlander version and the legacy ones.
+	 * The 'SCHEME' bits(30-31) of the revision register is used
+	 * to identify the version.
+	 */
+	if (readl_relaxed(vbase + OMAP2_32KSYNCNT_REV_OFF) &
+						OMAP2_32KSYNCNT_REV_SCHEME)
+		sync32k_cnt_reg = vbase + OMAP2_32KSYNCNT_CR_OFF_HIGH;
+	else
+		sync32k_cnt_reg = vbase + OMAP2_32KSYNCNT_CR_OFF_LOW;
+
+	/*
+	 * 120000 rough estimate from the calculations in
+	 * __clocksource_update_freq_scale.
+	 */
+	clocks_calc_mult_shift(&persistent_mult, &persistent_shift,
+			32768, NSEC_PER_SEC, 120000);
+
+	ret = clocksource_mmio_init(sync32k_cnt_reg, "32k_counter", 32768,
+				250, 32, clocksource_mmio_readl_up);
+	if (ret) {
+		pr_err("32k_counter: can't register clocksource\n");
+		return ret;
+	}
+
+	sched_clock_register(omap_32k_read_sched_clock, 32, 32768);
+	register_persistent_clock(omap_read_persistent_clock64);
+	pr_info("OMAP clocksource: 32k_counter at 32768 Hz\n");
+
+	return 0;
+}
+
 /*
  * ---------------------------------------------------------------------------
  * Timer initialization
@@ -180,7 +270,7 @@ int __init omap_32k_timer_init(void)
 
 		sync32k_ick = clk_get(NULL, "omap_32ksync_ick");
 		if (!IS_ERR(sync32k_ick))
-			clk_enable(sync32k_ick);
+			clk_prepare_enable(sync32k_ick);
 
 		ret = omap_init_clocksource_32k(base);
 	}
diff --git a/arch/arm/mach-omap1/usb.c b/arch/arm/mach-omap1/usb.c
index e60831c82b78..0119f3ddb7a6 100644
--- a/arch/arm/mach-omap1/usb.c
+++ b/arch/arm/mach-omap1/usb.c
@@ -12,13 +12,13 @@
 #include <linux/dma-map-ops.h>
 #include <linux/io.h>
 #include <linux/delay.h>
+#include <linux/soc/ti/omap1-io.h>
 
 #include <asm/irq.h>
 
-#include <mach/mux.h>
-
-#include <mach/usb.h>
-
+#include "hardware.h"
+#include "mux.h"
+#include "usb.h"
 #include "common.h"
 
 /* These routines should handle the standard chip-specific modes
diff --git a/arch/arm/mach-omap1/usb.h b/arch/arm/mach-omap1/usb.h
new file mode 100644
index 000000000000..08c9344c46e3
--- /dev/null
+++ b/arch/arm/mach-omap1/usb.h
@@ -0,0 +1,25 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * fixme correct answer depends on hmc_mode,
+ * as does (on omap1) any nonzero value for config->otg port number
+ */
+#include <linux/platform_data/usb-omap1.h>
+#include <linux/soc/ti/omap1-usb.h>
+
+#if IS_ENABLED(CONFIG_USB_OMAP)
+#define	is_usb0_device(config)	1
+#else
+#define	is_usb0_device(config)	0
+#endif
+
+#if IS_ENABLED(CONFIG_USB_SUPPORT)
+void omap1_usb_init(struct omap_usb_config *pdata);
+#else
+static inline void omap1_usb_init(struct omap_usb_config *pdata)
+{
+}
+#endif
+
+#define OMAP1_OHCI_BASE			0xfffba000
+#define OMAP2_OHCI_BASE			0x4805e000
+#define OMAP_OHCI_BASE			OMAP1_OHCI_BASE
diff --git a/arch/arm/mach-omap2/Kconfig b/arch/arm/mach-omap2/Kconfig
index 02c253de9b6e..3b53dda9ec79 100644
--- a/arch/arm/mach-omap2/Kconfig
+++ b/arch/arm/mach-omap2/Kconfig
@@ -105,6 +105,7 @@ config ARCH_OMAP2PLUS
 	select MACH_OMAP_GENERIC
 	select MEMORY
 	select MFD_SYSCON
+	select OMAP_DM_SYSTIMER
 	select OMAP_DM_TIMER
 	select OMAP_GPMC
 	select PINCTRL
@@ -122,7 +123,9 @@ config ARCH_OMAP2PLUS
 config OMAP_INTERCONNECT_BARRIER
 	bool
 	select ARM_HEAVY_MB
-	
+
+config ARCH_OMAP
+	bool
 
 if ARCH_OMAP2PLUS
 
@@ -153,6 +156,53 @@ config SOC_HAS_REALTIME_COUNTER
 	depends on SOC_OMAP5 || SOC_DRA7XX
 	default y
 
+config POWER_AVS_OMAP
+	bool "AVS(Adaptive Voltage Scaling) support for OMAP IP versions 1&2"
+	depends on (ARCH_OMAP3 || ARCH_OMAP4) && PM
+	select POWER_SUPPLY
+	help
+	  Say Y to enable AVS(Adaptive Voltage Scaling)
+	  support on OMAP containing the version 1 or
+	  version 2 of the SmartReflex IP.
+	  V1 is the 65nm version used in OMAP3430.
+	  V2 is the update for the 45nm version of the IP used in OMAP3630
+	  and OMAP4430
+
+	  Please note, that by default SmartReflex is only
+	  initialized and not enabled. To enable the automatic voltage
+	  compensation for vdd mpu and vdd core from user space,
+	  user must write 1 to
+		/debug/smartreflex/sr_<X>/autocomp,
+	  where X is mpu_iva or core for OMAP3.
+	  Optionally autocompensation can be enabled in the kernel
+	  by default during system init via the enable_on_init flag
+	  which an be passed as platform data to the smartreflex driver.
+
+config POWER_AVS_OMAP_CLASS3
+	bool "Class 3 mode of Smartreflex Implementation"
+	depends on POWER_AVS_OMAP && TWL4030_CORE
+	help
+	  Say Y to enable Class 3 implementation of Smartreflex
+
+	  Class 3 implementation of Smartreflex employs continuous hardware
+	  voltage calibration.
+
+config OMAP3_L2_AUX_SECURE_SAVE_RESTORE
+	bool "OMAP3 HS/EMU save and restore for L2 AUX control register"
+	depends on ARCH_OMAP3 && PM
+	help
+	  Without this option, L2 Auxiliary control register contents are
+	  lost during off-mode entry on HS/EMU devices. This feature
+	  requires support from PPA / boot-loader in HS/EMU devices, which
+	  currently does not exist by default.
+
+config OMAP3_L2_AUX_SECURE_SERVICE_SET_ID
+	int "Service ID for the support routine to set L2 AUX control"
+	depends on OMAP3_L2_AUX_SECURE_SAVE_RESTORE
+	default 43
+	help
+	  PPA routine service ID for setting L2 auxiliary control register.
+
 comment "OMAP Core Type"
 	depends on ARCH_OMAP2
 
@@ -160,6 +210,7 @@ config SOC_OMAP2420
 	bool "OMAP2420 support"
 	depends on ARCH_OMAP2
 	default y
+	select OMAP_DM_SYSTIMER
 	select OMAP_DM_TIMER
 	select SOC_HAS_OMAP2_SDRC
 
@@ -192,10 +243,10 @@ config MACH_OMAP2_TUSB6010
 	default y if MACH_NOKIA_N8X0
 
 config MACH_NOKIA_N810
-       bool
+	bool
 
 config MACH_NOKIA_N810_WIMAX
-       bool
+	bool
 
 config MACH_NOKIA_N8X0
 	bool "Nokia N800/N810"
diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile
index 8306ad686bc8..2feb9f6630af 100644
--- a/arch/arm/mach-omap2/Makefile
+++ b/arch/arm/mach-omap2/Makefile
@@ -3,9 +3,6 @@
 # Makefile for the linux kernel.
 #
 
-ccflags-y := -I$(srctree)/$(src)/include \
-	-I$(srctree)/arch/arm/plat-omap/include
-
 # Common support
 obj-y := id.o io.o control.o devices.o fb.o pm.o \
 	 common.o dma.o omap-headsmp.o sram.o
diff --git a/arch/arm/mach-omap2/am33xx.h b/arch/arm/mach-omap2/am33xx.h
index bf2b5f87e404..32bcfcf34817 100644
--- a/arch/arm/mach-omap2/am33xx.h
+++ b/arch/arm/mach-omap2/am33xx.h
@@ -1,16 +1,8 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * This file contains the address info for various AM33XX modules.
  *
  * Copyright (C) 2011 Texas Instruments, Inc. - https://www.ti.com/
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation version 2.
- *
- * This program is distributed "as is" WITHOUT ANY WARRANTY of any
- * kind, whether express or implied; without even the implied warranty
- * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
  */
 
 #ifndef __ASM_ARCH_AM33XX_H
diff --git a/arch/arm/mach-omap2/clockdomains33xx_data.c b/arch/arm/mach-omap2/clockdomains33xx_data.c
index b4d5144df445..87f4e927eb18 100644
--- a/arch/arm/mach-omap2/clockdomains33xx_data.c
+++ b/arch/arm/mach-omap2/clockdomains33xx_data.c
@@ -1,17 +1,9 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * AM33XX Clock Domain data.
  *
  * Copyright (C) 2011-2012 Texas Instruments Incorporated - https://www.ti.com/
  * Vaibhav Hiremath <hvaibhav@ti.com>
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation version 2.
- *
- * This program is distributed "as is" WITHOUT ANY WARRANTY of any
- * kind, whether express or implied; without even the implied warranty
- * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
  */
 
 #include <linux/kernel.h>
diff --git a/arch/arm/mach-omap2/clockdomains81xx_data.c b/arch/arm/mach-omap2/clockdomains81xx_data.c
index 127dc7ace71f..549cf61487a5 100644
--- a/arch/arm/mach-omap2/clockdomains81xx_data.c
+++ b/arch/arm/mach-omap2/clockdomains81xx_data.c
@@ -1,17 +1,9 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * TI81XX Clock Domain data.
  *
  * Copyright (C) 2010 Texas Instruments, Inc. - https://www.ti.com/
  * Copyright (C) 2013 SKTB SKiT, http://www.skitlab.ru/
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation version 2.
- *
- * This program is distributed "as is" WITHOUT ANY WARRANTY of any
- * kind, whether express or implied; without even the implied warranty
- * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
  */
 
 #ifndef __ARCH_ARM_MACH_OMAP2_CLOCKDOMAINS_81XX_H
diff --git a/arch/arm/mach-omap2/cm-regbits-33xx.h b/arch/arm/mach-omap2/cm-regbits-33xx.h
index e7ae2bb515e3..1b97219aaba4 100644
--- a/arch/arm/mach-omap2/cm-regbits-33xx.h
+++ b/arch/arm/mach-omap2/cm-regbits-33xx.h
@@ -1,3 +1,4 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * AM33XX Power Management register bits
  *
@@ -5,15 +6,6 @@
  * Vaibhav Hiremath <hvaibhav@ti.com>
  *
  * Copyright (C) 2011-2012 Texas Instruments Incorporated - https://www.ti.com/
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation version 2.
- *
- * This program is distributed "as is" WITHOUT ANY WARRANTY of any
- * kind, whether express or implied; without even the implied warranty
- * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
  */
 
 
diff --git a/arch/arm/mach-omap2/cm33xx.c b/arch/arm/mach-omap2/cm33xx.c
index ac4882ebdca3..d61fa06117b4 100644
--- a/arch/arm/mach-omap2/cm33xx.c
+++ b/arch/arm/mach-omap2/cm33xx.c
@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * AM33XX CM functions
  *
@@ -5,15 +6,6 @@
  * Vaibhav Hiremath <hvaibhav@ti.com>
  *
  * Reference taken from from OMAP4 cminst44xx.c
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation version 2.
- *
- * This program is distributed "as is" WITHOUT ANY WARRANTY of any
- * kind, whether express or implied; without even the implied warranty
- * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
  */
 
 #include <linux/kernel.h>
diff --git a/arch/arm/mach-omap2/cm33xx.h b/arch/arm/mach-omap2/cm33xx.h
index af63d1892c33..456267a7af71 100644
--- a/arch/arm/mach-omap2/cm33xx.h
+++ b/arch/arm/mach-omap2/cm33xx.h
@@ -1,17 +1,9 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * AM33XX CM offset macros
  *
  * Copyright (C) 2011-2012 Texas Instruments Incorporated - https://www.ti.com/
  * Vaibhav Hiremath <hvaibhav@ti.com>
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation version 2.
- *
- * This program is distributed "as is" WITHOUT ANY WARRANTY of any
- * kind, whether express or implied; without even the implied warranty
- * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
  */
 
 #ifndef __ARCH_ARM_MACH_OMAP2_CM_33XX_H
diff --git a/arch/arm/mach-omap2/cm81xx.h b/arch/arm/mach-omap2/cm81xx.h
index bd91223e838e..ffcde1812c6c 100644
--- a/arch/arm/mach-omap2/cm81xx.h
+++ b/arch/arm/mach-omap2/cm81xx.h
@@ -1,17 +1,9 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * Clock domain register offsets for TI81XX.
  *
  * Copyright (C) 2010 Texas Instruments, Inc. - https://www.ti.com/
  * Copyright (C) 2013 SKTB SKiT, http://www.skitlab.ru/
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation version 2.
- *
- * This program is distributed "as is" WITHOUT ANY WARRANTY of any
- * kind, whether express or implied; without even the implied warranty
- * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
  */
 
 #ifndef __ARCH_ARM_MACH_OMAP2_CM_TI81XX_H
diff --git a/arch/arm/mach-omap2/cm_common.c b/arch/arm/mach-omap2/cm_common.c
index e2d069fe67f1..87f2c2d2d754 100644
--- a/arch/arm/mach-omap2/cm_common.c
+++ b/arch/arm/mach-omap2/cm_common.c
@@ -320,8 +320,10 @@ int __init omap2_cm_base_init(void)
 		data = (struct omap_prcm_init_data *)match->data;
 
 		ret = of_address_to_resource(np, 0, &res);
-		if (ret)
+		if (ret) {
+			of_node_put(np);
 			return ret;
+		}
 
 		if (data->index == TI_CLKM_CM)
 			mem = &cm_base;
@@ -367,8 +369,10 @@ int __init omap_cm_init(void)
 			continue;
 
 		ret = omap2_clk_provider_init(np, data->index, NULL, data->mem);
-		if (ret)
+		if (ret) {
+			of_node_put(np);
 			return ret;
+		}
 	}
 
 	return 0;
diff --git a/arch/arm/mach-omap2/common.h b/arch/arm/mach-omap2/common.h
index 32f58f58515e..bd5981945239 100644
--- a/arch/arm/mach-omap2/common.h
+++ b/arch/arm/mach-omap2/common.h
@@ -266,7 +266,7 @@ extern void omap4_sar_ram_init(void);
 extern void __iomem *omap4_get_sar_ram_base(void);
 extern void omap4_mpuss_early_init(void);
 extern void omap_do_wfi(void);
-
+extern void omap_interconnect_sync(void);
 
 #ifdef CONFIG_SMP
 /* Needed for secondary core boot */
@@ -360,5 +360,16 @@ extern int omap_dss_reset(struct omap_hwmod *);
 /* SoC specific clock initializer */
 int omap_clk_init(void);
 
+#if IS_ENABLED(CONFIG_OMAP_IOMMU)
+int omap_iommu_set_pwrdm_constraint(struct platform_device *pdev, bool request,
+				    u8 *pwrst);
+#else
+static inline int omap_iommu_set_pwrdm_constraint(struct platform_device *pdev,
+						  bool request, u8 *pwrst)
+{
+	return 0;
+}
+#endif
+
 #endif /* __ASSEMBLER__ */
 #endif /* __ARCH_ARM_MACH_OMAP2PLUS_COMMON_H */
diff --git a/arch/arm/mach-omap2/control.c b/arch/arm/mach-omap2/control.c
index 062d431fc33a..c514a9602269 100644
--- a/arch/arm/mach-omap2/control.c
+++ b/arch/arm/mach-omap2/control.c
@@ -769,8 +769,10 @@ int __init omap2_control_base_init(void)
 		data = (struct control_init_data *)match->data;
 
 		mem = of_iomap(np, 0);
-		if (!mem)
+		if (!mem) {
+			of_node_put(np);
 			return -ENOMEM;
+		}
 
 		if (data->index == TI_CLKM_CTRL) {
 			omap2_ctrl_base = mem;
@@ -810,22 +812,24 @@ int __init omap_control_init(void)
 		if (scm_conf) {
 			syscon = syscon_node_to_regmap(scm_conf);
 
-			if (IS_ERR(syscon))
-				return PTR_ERR(syscon);
+			if (IS_ERR(syscon)) {
+				ret = PTR_ERR(syscon);
+				goto of_node_put;
+			}
 
 			if (of_get_child_by_name(scm_conf, "clocks")) {
 				ret = omap2_clk_provider_init(scm_conf,
 							      data->index,
 							      syscon, NULL);
 				if (ret)
-					return ret;
+					goto of_node_put;
 			}
 		} else {
 			/* No scm_conf found, direct access */
 			ret = omap2_clk_provider_init(np, data->index, NULL,
 						      data->mem);
 			if (ret)
-				return ret;
+				goto of_node_put;
 		}
 	}
 
@@ -836,6 +840,11 @@ int __init omap_control_init(void)
 	}
 
 	return 0;
+
+of_node_put:
+	of_node_put(np);
+	return ret;
+
 }
 
 /**
diff --git a/arch/arm/mach-omap2/display.c b/arch/arm/mach-omap2/display.c
index 6daaa645ae5d..dbec3bb9fbf4 100644
--- a/arch/arm/mach-omap2/display.c
+++ b/arch/arm/mach-omap2/display.c
@@ -1,18 +1,10 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * OMAP2plus display device setup / initialization.
  *
  * Copyright (C) 2010 Texas Instruments Incorporated - https://www.ti.com/
  *	Senthilvadivu Guruswamy
  *	Sumit Semwal
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- * This program is distributed "as is" WITHOUT ANY WARRANTY of any
- * kind, whether express or implied; without even the implied warranty
- * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
  */
 
 #include <linux/string.h>
@@ -211,6 +203,7 @@ static int __init omapdss_init_fbdev(void)
 	node = of_find_node_by_name(NULL, "omap4_padconf_global");
 	if (node)
 		omap4_dsi_mux_syscon = syscon_node_to_regmap(node);
+	of_node_put(node);
 
 	return 0;
 }
@@ -259,13 +252,15 @@ static int __init omapdss_init_of(void)
 
 	if (!pdev) {
 		pr_err("Unable to find DSS platform device\n");
+		of_node_put(node);
 		return -ENODEV;
 	}
 
 	r = of_platform_populate(node, NULL, NULL, &pdev->dev);
+	put_device(&pdev->dev);
+	of_node_put(node);
 	if (r) {
 		pr_err("Unable to populate DSS submodule devices\n");
-		put_device(&pdev->dev);
 		return r;
 	}
 
diff --git a/arch/arm/mach-omap2/dma.c b/arch/arm/mach-omap2/dma.c
index dfc9b21ff19b..830cd4e7eb44 100644
--- a/arch/arm/mach-omap2/dma.c
+++ b/arch/arm/mach-omap2/dma.c
@@ -30,6 +30,7 @@
 #include <linux/omap-dma.h>
 
 #include "soc.h"
+#include "common.h"
 
 static const struct omap_dma_reg reg_map[] = {
 	[REVISION]	= { 0x0000, 0x00, OMAP_DMA_REG_32BIT },
diff --git a/arch/arm/mach-omap2/include/mach/hardware.h b/arch/arm/mach-omap2/include/mach/hardware.h
deleted file mode 100644
index 54492dbf6973..000000000000
--- a/arch/arm/mach-omap2/include/mach/hardware.h
+++ /dev/null
@@ -1,3 +0,0 @@
-/*
- * arch/arm/mach-omap2/include/mach/hardware.h
- */
diff --git a/arch/arm/mach-omap2/include/mach/irqs.h b/arch/arm/mach-omap2/include/mach/irqs.h
deleted file mode 100644
index ba5282cafa42..000000000000
--- a/arch/arm/mach-omap2/include/mach/irqs.h
+++ /dev/null
@@ -1,3 +0,0 @@
-/*
- * arch/arm/mach-omap2/include/mach/irqs.h
- */
diff --git a/arch/arm/mach-omap2/include/mach/serial.h b/arch/arm/mach-omap2/include/mach/serial.h
deleted file mode 100644
index 7ca1fcff453b..000000000000
--- a/arch/arm/mach-omap2/include/mach/serial.h
+++ /dev/null
@@ -1,66 +0,0 @@
-/*
- * Copyright (C) 2009 Texas Instruments
- * Added OMAP4 support- Santosh Shilimkar <santosh.shilimkar@ti.com>
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- */
-
-/* OMAP2 serial ports */
-#define OMAP2_UART1_BASE	0x4806a000
-#define OMAP2_UART2_BASE	0x4806c000
-#define OMAP2_UART3_BASE	0x4806e000
-
-/* OMAP3 serial ports */
-#define OMAP3_UART1_BASE	OMAP2_UART1_BASE
-#define OMAP3_UART2_BASE	OMAP2_UART2_BASE
-#define OMAP3_UART3_BASE	0x49020000
-#define OMAP3_UART4_BASE	0x49042000	/* Only on 36xx */
-#define OMAP3_UART4_AM35XX_BASE	0x4809E000	/* Only on AM35xx */
-
-/* OMAP4 serial ports */
-#define OMAP4_UART1_BASE	OMAP2_UART1_BASE
-#define OMAP4_UART2_BASE	OMAP2_UART2_BASE
-#define OMAP4_UART3_BASE	0x48020000
-#define OMAP4_UART4_BASE	0x4806e000
-
-/* TI81XX serial ports */
-#define TI81XX_UART1_BASE	0x48020000
-#define TI81XX_UART2_BASE	0x48022000
-#define TI81XX_UART3_BASE	0x48024000
-
-/* AM3505/3517 UART4 */
-#define AM35XX_UART4_BASE	0x4809E000	/* Only on AM3505/3517 */
-
-/* AM33XX serial port */
-#define AM33XX_UART1_BASE	0x44E09000
-
-/* OMAP5 serial ports */
-#define OMAP5_UART1_BASE	OMAP2_UART1_BASE
-#define OMAP5_UART2_BASE	OMAP2_UART2_BASE
-#define OMAP5_UART3_BASE	OMAP4_UART3_BASE
-#define OMAP5_UART4_BASE	OMAP4_UART4_BASE
-#define OMAP5_UART5_BASE	0x48066000
-#define OMAP5_UART6_BASE	0x48068000
-
-/* External port on Zoom2/3 */
-#define ZOOM_UART_BASE		0x10000000
-#define ZOOM_UART_VIRT		0xfa400000
-
-#define OMAP_PORT_SHIFT		2
-#define ZOOM_PORT_SHIFT		1
-
-#define OMAP24XX_BASE_BAUD	(48000000/16)
-
-#ifndef __ASSEMBLER__
-
-struct omap_board_data;
-struct omap_uart_port_info;
-
-extern void omap_serial_init(void);
-extern void omap_serial_board_init(struct omap_uart_port_info *platform_data);
-extern void omap_serial_init_port(struct omap_board_data *bdata,
-		struct omap_uart_port_info *platform_data);
-#endif
diff --git a/arch/arm/mach-omap2/omap-iommu.c b/arch/arm/mach-omap2/omap-iommu.c
index 93c20bbd7b7e..9c8a85198e16 100644
--- a/arch/arm/mach-omap2/omap-iommu.c
+++ b/arch/arm/mach-omap2/omap-iommu.c
@@ -13,6 +13,7 @@
 
 #include "clockdomain.h"
 #include "powerdomain.h"
+#include "common.h"
 
 struct pwrdm_link {
 	struct device *dev;
diff --git a/arch/arm/mach-omap2/omap-secure.c b/arch/arm/mach-omap2/omap-secure.c
index 0659ab4cb0af..fb9c114b9dd7 100644
--- a/arch/arm/mach-omap2/omap-secure.c
+++ b/arch/arm/mach-omap2/omap-secure.c
@@ -59,8 +59,13 @@ static void __init omap_optee_init_check(void)
 u32 omap_secure_dispatcher(u32 idx, u32 flag, u32 nargs, u32 arg1, u32 arg2,
 							 u32 arg3, u32 arg4)
 {
+	static u32 buf[NR_CPUS][5];
+	u32 *param;
+	int cpu;
 	u32 ret;
-	u32 param[5];
+
+	cpu = get_cpu();
+	param = buf[cpu];
 
 	param[0] = nargs;
 	param[1] = arg1;
@@ -76,6 +81,8 @@ u32 omap_secure_dispatcher(u32 idx, u32 flag, u32 nargs, u32 arg1, u32 arg2,
 	outer_clean_range(__pa(param), __pa(param + 5));
 	ret = omap_smc2(idx, flag, __pa(param));
 
+	put_cpu();
+
 	return ret;
 }
 
@@ -117,10 +124,10 @@ phys_addr_t omap_secure_ram_mempool_base(void)
 }
 
 #if defined(CONFIG_ARCH_OMAP3) && defined(CONFIG_PM)
-u32 omap3_save_secure_ram(void __iomem *addr, int size)
+u32 omap3_save_secure_ram(void *addr, int size)
 {
+	static u32 param[5];
 	u32 ret;
-	u32 param[5];
 
 	if (size != OMAP3_SAVE_SECURE_RAM_SZ)
 		return OMAP3_SAVE_SECURE_RAM_SZ;
@@ -153,8 +160,8 @@ u32 omap3_save_secure_ram(void __iomem *addr, int size)
 u32 rx51_secure_dispatcher(u32 idx, u32 process, u32 flag, u32 nargs,
 			   u32 arg1, u32 arg2, u32 arg3, u32 arg4)
 {
+	static u32 param[5];
 	u32 ret;
-	u32 param[5];
 
 	param[0] = nargs+1; /* RX-51 needs number of arguments + 1 */
 	param[1] = arg1;
diff --git a/arch/arm/mach-omap2/omap-secure.h b/arch/arm/mach-omap2/omap-secure.h
index 172069f31616..9e67d4efdd0c 100644
--- a/arch/arm/mach-omap2/omap-secure.h
+++ b/arch/arm/mach-omap2/omap-secure.h
@@ -73,7 +73,7 @@ extern u32 omap_smc3(u32 id, u32 process, u32 flag, u32 pargs);
 extern phys_addr_t omap_secure_ram_mempool_base(void);
 extern int omap_secure_ram_reserve_memblock(void);
 extern u32 save_secure_ram_context(u32 args_pa);
-extern u32 omap3_save_secure_ram(void __iomem *save_regs, int size);
+extern u32 omap3_save_secure_ram(void *save_regs, int size);
 
 extern u32 rx51_secure_dispatcher(u32 idx, u32 process, u32 flag, u32 nargs,
 				  u32 arg1, u32 arg2, u32 arg3, u32 arg4);
diff --git a/arch/arm/mach-omap2/omap4-common.c b/arch/arm/mach-omap2/omap4-common.c
index 5c3845730dbf..6d1eb4eefefe 100644
--- a/arch/arm/mach-omap2/omap4-common.c
+++ b/arch/arm/mach-omap2/omap4-common.c
@@ -139,7 +139,7 @@ static int __init omap4_sram_init(void)
 		pr_warn("%s:Unable to get sram pool needed to handle errata I688\n",
 			__func__);
 	else
-		sram_sync = (void *)gen_pool_alloc(sram_pool, PAGE_SIZE);
+		sram_sync = (void __iomem *)gen_pool_alloc(sram_pool, PAGE_SIZE);
 
 	return 0;
 }
@@ -314,10 +314,12 @@ void __init omap_gic_of_init(void)
 
 	np = of_find_compatible_node(NULL, NULL, "arm,cortex-a9-gic");
 	gic_dist_base_addr = of_iomap(np, 0);
+	of_node_put(np);
 	WARN_ON(!gic_dist_base_addr);
 
 	np = of_find_compatible_node(NULL, NULL, "arm,cortex-a9-twd-timer");
 	twd_base = of_iomap(np, 0);
+	of_node_put(np);
 	WARN_ON(!twd_base);
 
 skip_errata_init:
diff --git a/arch/arm/mach-omap2/omap_device.c b/arch/arm/mach-omap2/omap_device.c
index 56d6814bec26..8b3701901991 100644
--- a/arch/arm/mach-omap2/omap_device.c
+++ b/arch/arm/mach-omap2/omap_device.c
@@ -96,9 +96,6 @@ static void _add_clkdev(struct omap_device *od, const char *clk_alias,
  * omap_device, this function adds an entry in the clkdev table of the
  * form <dev-id=dev_name, con-id=role> if it does not exist already.
  *
- * The function is called from inside omap_device_build_ss(), after
- * omap_device_register.
- *
  * This allows drivers to get a pointer to its optional clocks based on its role
  * by calling clk_get(<dev*>, <role>).
  * In the case of the main clock, a "fck" alias is used.
@@ -473,23 +470,6 @@ struct dev_pm_domain omap_device_pm_domain = {
 	}
 };
 
-/**
- * omap_device_register - register an omap_device with one omap_hwmod
- * @pdev: the platform device (omap_device) to register.
- *
- * Register the omap_device structure.  This currently just calls
- * platform_device_register() on the underlying platform_device.
- * Returns the return value of platform_device_register().
- */
-int omap_device_register(struct platform_device *pdev)
-{
-	pr_debug("omap_device: %s: registering\n", pdev->name);
-
-	dev_pm_domain_set(&pdev->dev, &omap_device_pm_domain);
-	return platform_device_add(pdev);
-}
-
-
 /* Public functions for use by device drivers through struct platform_data */
 
 /**
diff --git a/arch/arm/mach-omap2/omap_device.h b/arch/arm/mach-omap2/omap_device.h
index f77e76a7841a..d607532cf5e0 100644
--- a/arch/arm/mach-omap2/omap_device.h
+++ b/arch/arm/mach-omap2/omap_device.h
@@ -71,7 +71,6 @@ int omap_device_idle(struct platform_device *pdev);
 struct omap_device *omap_device_alloc(struct platform_device *pdev,
 				      struct omap_hwmod **ohs, int oh_cnt);
 void omap_device_delete(struct omap_device *od);
-int omap_device_register(struct platform_device *pdev);
 
 struct device *omap_device_get_by_hwmod_name(const char *oh_name);
 
diff --git a/arch/arm/mach-omap2/omap_hwmod.c b/arch/arm/mach-omap2/omap_hwmod.c
index ccb0e3732c0d..31d1a21f6041 100644
--- a/arch/arm/mach-omap2/omap_hwmod.c
+++ b/arch/arm/mach-omap2/omap_hwmod.c
@@ -752,8 +752,10 @@ static int __init _init_clkctrl_providers(void)
 
 	for_each_matching_node(np, ti_clkctrl_match_table) {
 		ret = _setup_clkctrl_provider(np);
-		if (ret)
+		if (ret) {
+			of_node_put(np);
 			break;
+		}
 	}
 
 	return ret;
diff --git a/arch/arm/mach-omap2/omap_hwmod_81xx_data.c b/arch/arm/mach-omap2/omap_hwmod_81xx_data.c
index 450ab990c66a..9b5c728fb7da 100644
--- a/arch/arm/mach-omap2/omap_hwmod_81xx_data.c
+++ b/arch/arm/mach-omap2/omap_hwmod_81xx_data.c
@@ -1,18 +1,9 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * DM81xx hwmod data.
  *
  * Copyright (C) 2010 Texas Instruments, Inc. - https://www.ti.com/
  * Copyright (C) 2013 SKTB SKiT, http://www.skitlab.ru/
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation version 2.
- *
- * This program is distributed "as is" WITHOUT ANY WARRANTY of any
- * kind, whether express or implied; without even the implied warranty
- * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
  */
 
 #include <linux/types.h>
diff --git a/arch/arm/mach-omap2/omap_opp_data.h b/arch/arm/mach-omap2/omap_opp_data.h
index 533dd643069a..88375ab38e31 100644
--- a/arch/arm/mach-omap2/omap_opp_data.h
+++ b/arch/arm/mach-omap2/omap_opp_data.h
@@ -1,3 +1,4 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * OMAP SoC specific OPP Data helpers
  *
@@ -6,15 +7,6 @@
  *	Kevin Hilman
  * Copyright (C) 2010 Nokia Corporation.
  *      Eduardo Valentin
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- * This program is distributed "as is" WITHOUT ANY WARRANTY of any
- * kind, whether express or implied; without even the implied warranty
- * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
  */
 #ifndef __ARCH_ARM_MACH_OMAP2_OMAP_OPP_DATA_H
 #define __ARCH_ARM_MACH_OMAP2_OMAP_OPP_DATA_H
diff --git a/arch/arm/mach-omap2/opp3xxx_data.c b/arch/arm/mach-omap2/opp3xxx_data.c
index b610c5fb423b..90257e2fb3d6 100644
--- a/arch/arm/mach-omap2/opp3xxx_data.c
+++ b/arch/arm/mach-omap2/opp3xxx_data.c
@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * OMAP3 OPP table definitions.
  *
@@ -7,15 +8,6 @@
  * Copyright (C) 2010-2011 Nokia Corporation.
  *      Eduardo Valentin
  *      Paul Walmsley
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- * This program is distributed "as is" WITHOUT ANY WARRANTY of any
- * kind, whether express or implied; without even the implied warranty
- * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
  */
 #include <linux/module.h>
 
diff --git a/arch/arm/mach-omap2/opp4xxx_data.c b/arch/arm/mach-omap2/opp4xxx_data.c
index d937c5ef41c6..a9851886017d 100644
--- a/arch/arm/mach-omap2/opp4xxx_data.c
+++ b/arch/arm/mach-omap2/opp4xxx_data.c
@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * OMAP4 OPP table definitions.
  *
@@ -8,15 +9,6 @@
  * Copyright (C) 2010-2011 Nokia Corporation.
  *      Eduardo Valentin
  *      Paul Walmsley
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- * This program is distributed "as is" WITHOUT ANY WARRANTY of any
- * kind, whether express or implied; without even the implied warranty
- * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
  */
 #include <linux/module.h>
 
diff --git a/arch/arm/mach-omap2/pdata-quirks.c b/arch/arm/mach-omap2/pdata-quirks.c
index e7fd29a502a0..5b99d602c87b 100644
--- a/arch/arm/mach-omap2/pdata-quirks.c
+++ b/arch/arm/mach-omap2/pdata-quirks.c
@@ -43,17 +43,6 @@ struct pdata_init {
 static struct of_dev_auxdata omap_auxdata_lookup[];
 static struct twl4030_gpio_platform_data twl_gpio_auxdata;
 
-#if IS_ENABLED(CONFIG_OMAP_IOMMU)
-int omap_iommu_set_pwrdm_constraint(struct platform_device *pdev, bool request,
-				    u8 *pwrst);
-#else
-static inline int omap_iommu_set_pwrdm_constraint(struct platform_device *pdev,
-						  bool request, u8 *pwrst)
-{
-	return 0;
-}
-#endif
-
 #ifdef CONFIG_MACH_NOKIA_N8X0
 static void __init omap2420_n8x0_legacy_init(void)
 {
@@ -551,6 +540,8 @@ pdata_quirks_init_clocks(const struct of_device_id *omap_dt_match_table)
 
 		of_platform_populate(np, omap_dt_match_table,
 				     omap_auxdata_lookup, NULL);
+
+		of_node_put(np);
 	}
 }
 
diff --git a/arch/arm/mach-omap2/powerdomains33xx_data.c b/arch/arm/mach-omap2/powerdomains33xx_data.c
index 626055e59aed..1d58fd1a2dce 100644
--- a/arch/arm/mach-omap2/powerdomains33xx_data.c
+++ b/arch/arm/mach-omap2/powerdomains33xx_data.c
@@ -1,16 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * AM33XX Power domain data
  *
  * Copyright (C) 2011-2012 Texas Instruments Incorporated - https://www.ti.com/
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation version 2.
- *
- * This program is distributed "as is" WITHOUT ANY WARRANTY of any
- * kind, whether express or implied; without even the implied warranty
- * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
  */
 
 #include <linux/kernel.h>
diff --git a/arch/arm/mach-omap2/prcm43xx.h b/arch/arm/mach-omap2/prcm43xx.h
index b65cccab6ad9..38ed69b150cb 100644
--- a/arch/arm/mach-omap2/prcm43xx.h
+++ b/arch/arm/mach-omap2/prcm43xx.h
@@ -1,11 +1,8 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * AM43x PRCM defines
  *
  * Copyright (C) 2013 Texas Instruments Incorporated - https://www.ti.com/
- *
- * This file is licensed under the terms of the GNU General Public License
- * version 2.  This program is licensed "as is" without any warranty of any
- * kind, whether express or implied.
  */
 
 #ifndef __ARCH_ARM_MACH_OMAP2_PRCM_43XX_H
diff --git a/arch/arm/mach-omap2/prm-regbits-33xx.h b/arch/arm/mach-omap2/prm-regbits-33xx.h
index 7dfdff09ddeb..3748c5266ae1 100644
--- a/arch/arm/mach-omap2/prm-regbits-33xx.h
+++ b/arch/arm/mach-omap2/prm-regbits-33xx.h
@@ -1,16 +1,8 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * AM33XX PRM_XXX register bits
  *
  * Copyright (C) 2011-2012 Texas Instruments Incorporated - https://www.ti.com/
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation version 2.
- *
- * This program is distributed "as is" WITHOUT ANY WARRANTY of any
- * kind, whether express or implied; without even the implied warranty
- * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
  */
 
 #ifndef __ARCH_ARM_MACH_OMAP2_PRM_REGBITS_33XX_H
diff --git a/arch/arm/mach-omap2/prm33xx.c b/arch/arm/mach-omap2/prm33xx.c
index 9144cc0479af..4b65a0f9cf7d 100644
--- a/arch/arm/mach-omap2/prm33xx.c
+++ b/arch/arm/mach-omap2/prm33xx.c
@@ -1,16 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * AM33XX PRM functions
  *
  * Copyright (C) 2011-2012 Texas Instruments Incorporated - https://www.ti.com/
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation version 2.
- *
- * This program is distributed "as is" WITHOUT ANY WARRANTY of any
- * kind, whether express or implied; without even the implied warranty
- * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
  */
 
 #include <linux/kernel.h>
diff --git a/arch/arm/mach-omap2/prm33xx.h b/arch/arm/mach-omap2/prm33xx.h
index a469a36c00d8..3081f3deb650 100644
--- a/arch/arm/mach-omap2/prm33xx.h
+++ b/arch/arm/mach-omap2/prm33xx.h
@@ -1,16 +1,8 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * AM33XX PRM instance offset macros
  *
  * Copyright (C) 2011-2012 Texas Instruments Incorporated - https://www.ti.com/
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation version 2.
- *
- * This program is distributed "as is" WITHOUT ANY WARRANTY of any
- * kind, whether express or implied; without even the implied warranty
- * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
  */
 
 #ifndef __ARCH_ARM_MACH_OMAP2_PRM33XX_H
diff --git a/arch/arm/mach-omap2/prm3xxx.c b/arch/arm/mach-omap2/prm3xxx.c
index 1b442b128569..63e73e9b82bc 100644
--- a/arch/arm/mach-omap2/prm3xxx.c
+++ b/arch/arm/mach-omap2/prm3xxx.c
@@ -708,6 +708,7 @@ static int omap3xxx_prm_late_init(void)
 	}
 
 	irq_num = of_irq_get(np, 0);
+	of_node_put(np);
 	if (irq_num == -EPROBE_DEFER)
 		return irq_num;
 
diff --git a/arch/arm/mach-omap2/prm_common.c b/arch/arm/mach-omap2/prm_common.c
index 65b2d82efa27..fb2d48cfe756 100644
--- a/arch/arm/mach-omap2/prm_common.c
+++ b/arch/arm/mach-omap2/prm_common.c
@@ -752,8 +752,10 @@ int __init omap2_prm_base_init(void)
 		data = (struct omap_prcm_init_data *)match->data;
 
 		ret = of_address_to_resource(np, 0, &res);
-		if (ret)
+		if (ret) {
+			of_node_put(np);
 			return ret;
+		}
 
 		data->mem = ioremap(res.start, resource_size(&res));
 
@@ -799,8 +801,10 @@ int __init omap_prcm_init(void)
 		data = match->data;
 
 		ret = omap2_clk_provider_init(np, data->index, NULL, data->mem);
-		if (ret)
+		if (ret) {
+			of_node_put(np);
 			return ret;
+		}
 	}
 
 	omap_cm_init();
diff --git a/arch/arm/mach-omap2/serial.h b/arch/arm/mach-omap2/serial.h
index c4014f013df0..7ca1fcff453b 100644
--- a/arch/arm/mach-omap2/serial.h
+++ b/arch/arm/mach-omap2/serial.h
@@ -1 +1,66 @@
-#include <mach/serial.h>
+/*
+ * Copyright (C) 2009 Texas Instruments
+ * Added OMAP4 support- Santosh Shilimkar <santosh.shilimkar@ti.com>
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+/* OMAP2 serial ports */
+#define OMAP2_UART1_BASE	0x4806a000
+#define OMAP2_UART2_BASE	0x4806c000
+#define OMAP2_UART3_BASE	0x4806e000
+
+/* OMAP3 serial ports */
+#define OMAP3_UART1_BASE	OMAP2_UART1_BASE
+#define OMAP3_UART2_BASE	OMAP2_UART2_BASE
+#define OMAP3_UART3_BASE	0x49020000
+#define OMAP3_UART4_BASE	0x49042000	/* Only on 36xx */
+#define OMAP3_UART4_AM35XX_BASE	0x4809E000	/* Only on AM35xx */
+
+/* OMAP4 serial ports */
+#define OMAP4_UART1_BASE	OMAP2_UART1_BASE
+#define OMAP4_UART2_BASE	OMAP2_UART2_BASE
+#define OMAP4_UART3_BASE	0x48020000
+#define OMAP4_UART4_BASE	0x4806e000
+
+/* TI81XX serial ports */
+#define TI81XX_UART1_BASE	0x48020000
+#define TI81XX_UART2_BASE	0x48022000
+#define TI81XX_UART3_BASE	0x48024000
+
+/* AM3505/3517 UART4 */
+#define AM35XX_UART4_BASE	0x4809E000	/* Only on AM3505/3517 */
+
+/* AM33XX serial port */
+#define AM33XX_UART1_BASE	0x44E09000
+
+/* OMAP5 serial ports */
+#define OMAP5_UART1_BASE	OMAP2_UART1_BASE
+#define OMAP5_UART2_BASE	OMAP2_UART2_BASE
+#define OMAP5_UART3_BASE	OMAP4_UART3_BASE
+#define OMAP5_UART4_BASE	OMAP4_UART4_BASE
+#define OMAP5_UART5_BASE	0x48066000
+#define OMAP5_UART6_BASE	0x48068000
+
+/* External port on Zoom2/3 */
+#define ZOOM_UART_BASE		0x10000000
+#define ZOOM_UART_VIRT		0xfa400000
+
+#define OMAP_PORT_SHIFT		2
+#define ZOOM_PORT_SHIFT		1
+
+#define OMAP24XX_BASE_BAUD	(48000000/16)
+
+#ifndef __ASSEMBLER__
+
+struct omap_board_data;
+struct omap_uart_port_info;
+
+extern void omap_serial_init(void);
+extern void omap_serial_board_init(struct omap_uart_port_info *platform_data);
+extern void omap_serial_init_port(struct omap_board_data *bdata,
+		struct omap_uart_port_info *platform_data);
+#endif
diff --git a/arch/arm/mach-omap2/sram.c b/arch/arm/mach-omap2/sram.c
index c98855f5594b..39cf270da718 100644
--- a/arch/arm/mach-omap2/sram.c
+++ b/arch/arm/mach-omap2/sram.c
@@ -18,6 +18,7 @@
 #include <asm/fncpy.h>
 #include <asm/tlb.h>
 #include <asm/cacheflush.h>
+#include <asm/set_memory.h>
 
 #include <asm/mach/map.h>
 
@@ -47,8 +48,68 @@
 #define ROUND_DOWN(value,boundary)	((value) & (~((boundary)-1)))
 
 static unsigned long omap_sram_start;
-static unsigned long omap_sram_skip;
 static unsigned long omap_sram_size;
+static void __iomem *omap_sram_base;
+static unsigned long omap_sram_skip;
+static void __iomem *omap_sram_ceil;
+
+/*
+ * Memory allocator for SRAM: calculates the new ceiling address
+ * for pushing a function using the fncpy API.
+ *
+ * Note that fncpy requires the returned address to be aligned
+ * to an 8-byte boundary.
+ */
+static void *omap_sram_push_address(unsigned long size)
+{
+	unsigned long available, new_ceil = (unsigned long)omap_sram_ceil;
+
+	available = omap_sram_ceil - (omap_sram_base + omap_sram_skip);
+
+	if (size > available) {
+		pr_err("Not enough space in SRAM\n");
+		return NULL;
+	}
+
+	new_ceil -= size;
+	new_ceil = ROUND_DOWN(new_ceil, FNCPY_ALIGN);
+	omap_sram_ceil = IOMEM(new_ceil);
+
+	return (void __force *)omap_sram_ceil;
+}
+
+void *omap_sram_push(void *funcp, unsigned long size)
+{
+	void *sram;
+	unsigned long base;
+	int pages;
+	void *dst = NULL;
+
+	sram = omap_sram_push_address(size);
+	if (!sram)
+		return NULL;
+
+	base = (unsigned long)sram & PAGE_MASK;
+	pages = PAGE_ALIGN(size) / PAGE_SIZE;
+
+	set_memory_rw(base, pages);
+
+	dst = fncpy(sram, funcp, size);
+
+	set_memory_ro(base, pages);
+	set_memory_x(base, pages);
+
+	return dst;
+}
+
+/*
+ * The SRAM context is lost during off-idle and stack
+ * needs to be reset.
+ */
+static void omap_sram_reset(void)
+{
+	omap_sram_ceil = omap_sram_base + omap_sram_size;
+}
 
 /*
  * Depending on the target RAMFS firewall setup, the public usable amount of
@@ -119,6 +180,8 @@ static void __init omap_detect_sram(void)
  */
 static void __init omap2_map_sram(void)
 {
+	unsigned long base;
+	int pages;
 	int cached = 1;
 
 	if (cpu_is_omap34xx()) {
@@ -132,8 +195,30 @@ static void __init omap2_map_sram(void)
 		cached = 0;
 	}
 
-	omap_map_sram(omap_sram_start, omap_sram_size,
-			omap_sram_skip, cached);
+	if (omap_sram_size == 0)
+		return;
+
+	omap_sram_start = ROUND_DOWN(omap_sram_start, PAGE_SIZE);
+	omap_sram_base = __arm_ioremap_exec(omap_sram_start, omap_sram_size, cached);
+	if (!omap_sram_base) {
+		pr_err("SRAM: Could not map\n");
+		return;
+	}
+
+	omap_sram_reset();
+
+	/*
+	 * Looks like we need to preserve some bootloader code at the
+	 * beginning of SRAM for jumping to flash for reboot to work...
+	 */
+	memset_io(omap_sram_base + omap_sram_skip, 0,
+		  omap_sram_size - omap_sram_skip);
+
+	base = (unsigned long)omap_sram_base;
+	pages = PAGE_ALIGN(omap_sram_size) / PAGE_SIZE;
+
+	set_memory_ro(base, pages);
+	set_memory_x(base, pages);
 }
 
 static void (*_omap2_sram_ddr_init)(u32 *slow_dll_ctrl, u32 fast_dll_ctrl,
diff --git a/arch/arm/mach-omap2/sram.h b/arch/arm/mach-omap2/sram.h
index 447bd3eed0fd..271062f23482 100644
--- a/arch/arm/mach-omap2/sram.h
+++ b/arch/arm/mach-omap2/sram.h
@@ -4,7 +4,6 @@
  */
 
 #ifndef __ASSEMBLY__
-#include <plat/sram.h>
 
 extern void omap2_sram_ddr_init(u32 *slow_dll_ctrl, u32 fast_dll_ctrl,
 				u32 base_cs, u32 force_unlock);
@@ -14,6 +13,10 @@ extern u32 omap2_set_prcm(u32 dpll_ctrl_val, u32 sdrc_rfr_val, int bypass);
 
 extern void omap3_sram_restore_context(void);
 
+extern int __init omap_sram_init(void);
+
+extern void *omap_sram_push(void *funcp, unsigned long size);
+
 /* Do not use these */
 extern void omap24xx_sram_reprogram_clock(u32 ckctl, u32 dpllctl);
 extern unsigned long omap24xx_sram_reprogram_clock_sz;
diff --git a/arch/arm/mach-omap2/ti81xx.h b/arch/arm/mach-omap2/ti81xx.h
index 192b0e7d3eb4..fe9f7f388cbd 100644
--- a/arch/arm/mach-omap2/ti81xx.h
+++ b/arch/arm/mach-omap2/ti81xx.h
@@ -1,16 +1,8 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * This file contains the address data for various TI81XX modules.
  *
  * Copyright (C) 2010 Texas Instruments, Inc. - https://www.ti.com/
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation version 2.
- *
- * This program is distributed "as is" WITHOUT ANY WARRANTY of any
- * kind, whether express or implied; without even the implied warranty
- * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
  */
 
 #ifndef __ASM_ARCH_TI81XX_H
diff --git a/arch/arm/mach-omap2/vc.c b/arch/arm/mach-omap2/vc.c
index 86f1ac4c2412..ea02d40405c4 100644
--- a/arch/arm/mach-omap2/vc.c
+++ b/arch/arm/mach-omap2/vc.c
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * OMAP Voltage Controller (VC) interface
  *
  * Copyright (C) 2011 Texas Instruments, Inc.
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 #include <linux/kernel.h>
 #include <linux/delay.h>
@@ -895,4 +892,3 @@ void __init omap_vc_init_channel(struct voltagedomain *voltdm)
 	else if (cpu_is_omap44xx())
 		omap4_vc_init_channel(voltdm);
 }
-
diff --git a/arch/arm/mach-orion5x/Kconfig b/arch/arm/mach-orion5x/Kconfig
index e94a61901ffd..0044b2823710 100644
--- a/arch/arm/mach-orion5x/Kconfig
+++ b/arch/arm/mach-orion5x/Kconfig
@@ -1,11 +1,13 @@
 # SPDX-License-Identifier: GPL-2.0-only
 menuconfig ARCH_ORION5X
 	bool "Marvell Orion"
-	depends on MMU && ARCH_MULTI_V5
+	depends on ARCH_MULTI_V5
+	depends on CPU_LITTLE_ENDIAN
 	select CPU_FEROCEON
 	select GPIOLIB
 	select MVEBU_MBUS
 	select FORCE_PCI
+	select PCI_QUIRKS
 	select PHYLIB if NETDEVICES
 	select PLAT_ORION_LEGACY
 	help
@@ -29,6 +31,7 @@ config ARCH_ORION5X_DT
 config MACH_DB88F5281
 	bool "Marvell Orion-2 Development Board"
 	select I2C_BOARDINFO if I2C
+	depends on ATAGS && UNUSED_BOARD_FILES
 	help
 	  Say 'Y' here if you want your kernel to support the
 	  Marvell Orion-2 (88F5281) Development Board
@@ -36,6 +39,7 @@ config MACH_DB88F5281
 config MACH_RD88F5182
 	bool "Marvell Orion-NAS Reference Design"
 	select I2C_BOARDINFO if I2C
+	depends on ATAGS && UNUSED_BOARD_FILES
 	help
 	  Say 'Y' here if you want your kernel to support the
 	  Marvell Orion-NAS (88F5182) RD2
@@ -51,6 +55,7 @@ config MACH_RD88F5182_DT
 config MACH_KUROBOX_PRO
 	bool "KuroBox Pro"
 	select I2C_BOARDINFO if I2C
+	depends on ATAGS
 	help
 	  Say 'Y' here if you want your kernel to support the
 	  KuroBox Pro platform.
@@ -58,24 +63,28 @@ config MACH_KUROBOX_PRO
 config MACH_DNS323
 	bool "D-Link DNS-323"
 	select I2C_BOARDINFO if I2C
+	depends on ATAGS
 	help
 	  Say 'Y' here if you want your kernel to support the
 	  D-Link DNS-323 platform.
 
 config MACH_TS209
 	bool "QNAP TS-109/TS-209"
+	depends on ATAGS
 	help
 	  Say 'Y' here if you want your kernel to support the
 	  QNAP TS-109/TS-209 platform.
 
 config MACH_TERASTATION_PRO2
 	bool "Buffalo Terastation Pro II/Live"
+	depends on ATAGS
 	help
 	  Say 'Y' here if you want your kernel to support the
 	  Buffalo Terastation Pro II/Live platform.
 
 config MACH_LINKSTATION_PRO
 	bool "Buffalo Linkstation Pro/Live"
+	depends on ATAGS
 	select I2C_BOARDINFO if I2C
 	help
 	  Say 'Y' here if you want your kernel to support the
@@ -91,6 +100,7 @@ config MACH_LINKSTATION_MINI
 
 config MACH_LINKSTATION_LS_HGL
 	bool "Buffalo Linkstation LS-HGL"
+	depends on ATAGS && UNUSED_BOARD_FILES
 	select I2C_BOARDINFO if I2C
 	help
 	  Say 'Y' here if you want your kernel to support the
@@ -98,24 +108,28 @@ config MACH_LINKSTATION_LS_HGL
 
 config MACH_TS409
 	bool "QNAP TS-409"
+	depends on ATAGS
 	help
 	  Say 'Y' here if you want your kernel to support the
 	  QNAP TS-409 platform.
 
 config MACH_WRT350N_V2
 	bool "Linksys WRT350N v2"
+	depends on ATAGS && UNUSED_BOARD_FILES
 	help
 	  Say 'Y' here if you want your kernel to support the
 	  Linksys WRT350N v2 platform.
 
 config MACH_TS78XX
 	bool "Technologic Systems TS-78xx"
+	depends on ATAGS
 	help
 	  Say 'Y' here if you want your kernel to support the
 	  Technologic Systems TS-78xx platform.
 
 config MACH_MV2120
 	bool "HP Media Vault mv2120"
+	depends on ATAGS
 	help
 	  Say 'Y' here if you want your kernel to support the
 	  HP Media Vault mv2120 or mv5100.
@@ -129,6 +143,7 @@ config MACH_D2NET_DT
 
 config MACH_NET2BIG
 	bool "LaCie 2Big Network"
+	depends on ATAGS
 	select I2C_BOARDINFO if I2C
 	help
 	  Say 'Y' here if you want your kernel to support the
@@ -143,24 +158,28 @@ config MACH_MSS2_DT
 
 config MACH_WNR854T
 	bool "Netgear WNR854T"
+	depends on ATAGS && UNUSED_BOARD_FILES
 	help
 	  Say 'Y' here if you want your kernel to support the
 	  Netgear WNR854T platform.
 
 config MACH_RD88F5181L_GE
 	bool "Marvell Orion-VoIP GE Reference Design"
+	depends on ATAGS && UNUSED_BOARD_FILES
 	help
 	  Say 'Y' here if you want your kernel to support the
 	  Marvell Orion-VoIP GE (88F5181L) RD.
 
 config MACH_RD88F5181L_FXO
 	bool "Marvell Orion-VoIP FXO Reference Design"
+	depends on ATAGS && UNUSED_BOARD_FILES
 	help
 	  Say 'Y' here if you want your kernel to support the
 	  Marvell Orion-VoIP FXO (88F5181L) RD.
 
 config MACH_RD88F6183AP_GE
 	bool "Marvell Orion-1-90 AP GE Reference Design"
+	depends on ATAGS && UNUSED_BOARD_FILES
 	help
 	  Say 'Y' here if you want your kernel to support the
 	  Marvell Orion-1-90 (88F6183) AP GE RD.
diff --git a/arch/arm/mach-orion5x/Makefile b/arch/arm/mach-orion5x/Makefile
index 1a585a62d5e6..572c3520f7fe 100644
--- a/arch/arm/mach-orion5x/Makefile
+++ b/arch/arm/mach-orion5x/Makefile
@@ -1,5 +1,5 @@
 # SPDX-License-Identifier: GPL-2.0
-ccflags-$(CONFIG_ARCH_MULTIPLATFORM) := -I$(srctree)/arch/arm/plat-orion/include
+ccflags-y := -I$(srctree)/arch/arm/plat-orion/include
 
 obj-y				+= common.o pci.o irq.o mpp.o
 obj-$(CONFIG_MACH_DB88F5281)	+= db88f5281-setup.o
diff --git a/arch/arm/mach-orion5x/board-d2net.c b/arch/arm/mach-orion5x/board-d2net.c
index a89376a5cd92..0297e302d7bc 100644
--- a/arch/arm/mach-orion5x/board-d2net.c
+++ b/arch/arm/mach-orion5x/board-d2net.c
@@ -1,13 +1,10 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/mach-orion5x/board-d2net.c
  *
  * LaCie d2Network and Big Disk Network NAS setup
  *
  * Copyright (C) 2009 Simon Guinot <sguinot@lacie.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #include <linux/kernel.h>
diff --git a/arch/arm/mach-orion5x/board-dt.c b/arch/arm/mach-orion5x/board-dt.c
index 3d36f1d95196..e3736ffc8347 100644
--- a/arch/arm/mach-orion5x/board-dt.c
+++ b/arch/arm/mach-orion5x/board-dt.c
@@ -1,13 +1,10 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Copyright 2012 (C), Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
  *
  * arch/arm/mach-orion5x/board-dt.c
  *
  * Flattened Device Tree board initialization
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #include <linux/kernel.h>
diff --git a/arch/arm/mach-orion5x/board-rd88f5182.c b/arch/arm/mach-orion5x/board-rd88f5182.c
index b7b0f52f4c0a..596601367989 100644
--- a/arch/arm/mach-orion5x/board-rd88f5182.c
+++ b/arch/arm/mach-orion5x/board-rd88f5182.c
@@ -1,13 +1,10 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/mach-orion5x/rd88f5182-setup.c
  *
  * Marvell Orion-NAS Reference Design Setup
  *
  * Maintainer: Ronen Shitrit <rshitrit@marvell.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 #include <linux/gpio.h>
 #include <linux/kernel.h>
diff --git a/arch/arm/mach-orion5x/bridge-regs.h b/arch/arm/mach-orion5x/bridge-regs.h
index 305598eaaee1..fe85bc5b131f 100644
--- a/arch/arm/mach-orion5x/bridge-regs.h
+++ b/arch/arm/mach-orion5x/bridge-regs.h
@@ -1,10 +1,5 @@
-/*
- * Orion CPU Bridge Registers
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
+/* SPDX-License-Identifier: GPL-2.0-only */
+/* Orion CPU Bridge Registers */
 
 #ifndef __ASM_ARCH_BRIDGE_REGS_H
 #define __ASM_ARCH_BRIDGE_REGS_H
diff --git a/arch/arm/mach-orion5x/common.c b/arch/arm/mach-orion5x/common.c
index 7bcb41137bbf..2e711b7252c6 100644
--- a/arch/arm/mach-orion5x/common.c
+++ b/arch/arm/mach-orion5x/common.c
@@ -1,13 +1,10 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/mach-orion5x/common.c
  *
  * Core functions for Marvell Orion 5x SoCs
  *
  * Maintainer: Tzachi Perelstein <tzachi@marvell.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #include <linux/kernel.h>
diff --git a/arch/arm/mach-orion5x/db88f5281-setup.c b/arch/arm/mach-orion5x/db88f5281-setup.c
index 39eae10ac8de..fe1a4cef1ba2 100644
--- a/arch/arm/mach-orion5x/db88f5281-setup.c
+++ b/arch/arm/mach-orion5x/db88f5281-setup.c
@@ -1,13 +1,10 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/mach-orion5x/db88f5281-setup.c
  *
  * Marvell Orion-2 Development Board Setup
  *
  * Maintainer: Tzachi Perelstein <tzachi@marvell.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 #include <linux/gpio.h>
 #include <linux/kernel.h>
diff --git a/arch/arm/mach-orion5x/dns323-setup.c b/arch/arm/mach-orion5x/dns323-setup.c
index 87cb47220e82..d69259b6b60d 100644
--- a/arch/arm/mach-orion5x/dns323-setup.c
+++ b/arch/arm/mach-orion5x/dns323-setup.c
@@ -696,12 +696,12 @@ static void __init dns323_init(void)
 			pr_err("DNS-323: failed to setup power-off GPIO\n");
 		pm_power_off = dns323c_power_off;
 
-		/* Now, -this- should theorically be done by the sata_mv driver
+		/* Now, -this- should theoretically be done by the sata_mv driver
 		 * once I figure out what's going on there. Maybe the behaviour
 		 * of the LEDs should be somewhat passed via the platform_data.
 		 * for now, just whack the register and make the LEDs happy
 		 *
-		 * Note: AFAIK, rev B1 needs the same treatement but I'll let
+		 * Note: AFAIK, rev B1 needs the same treatment but I'll let
 		 * somebody else test it.
 		 */
 		writel(0x5, ORION5X_SATA_VIRT_BASE + 0x2c);
diff --git a/arch/arm/mach-orion5x/irq.c b/arch/arm/mach-orion5x/irq.c
index ac4af2283bef..e17727e53cb4 100644
--- a/arch/arm/mach-orion5x/irq.c
+++ b/arch/arm/mach-orion5x/irq.c
@@ -1,13 +1,10 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/mach-orion5x/irq.c
  *
  * Core IRQ functions for Marvell Orion System On Chip
  *
  * Maintainer: Tzachi Perelstein <tzachi@marvell.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 #include <linux/gpio.h>
 #include <linux/kernel.h>
@@ -49,6 +46,6 @@ void __init orion5x_init_irq(void)
 	/*
 	 * Initialize gpiolib for GPIOs 0-31.
 	 */
-	orion_gpio_init(NULL, 0, 32, GPIO_VIRT_BASE, 0,
+	orion_gpio_init(0, 32, GPIO_VIRT_BASE, 0,
 			IRQ_ORION5X_GPIO_START, gpio0_irqs);
 }
diff --git a/arch/arm/mach-orion5x/irqs.h b/arch/arm/mach-orion5x/irqs.h
index 506c8e0b30c4..a70c47cfa6bc 100644
--- a/arch/arm/mach-orion5x/irqs.h
+++ b/arch/arm/mach-orion5x/irqs.h
@@ -1,11 +1,8 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * IRQ definitions for Orion SoC
  *
  *  Maintainer: Tzachi Perelstein <tzachi@marvell.com>
- *
- *  This file is licensed under the terms of the GNU General Public
- *  License version 2. This program is licensed "as is" without any
- *  warranty of any kind, whether express or implied.
  */
 
 #ifndef __ASM_ARCH_IRQS_H
diff --git a/arch/arm/mach-orion5x/kurobox_pro-setup.c b/arch/arm/mach-orion5x/kurobox_pro-setup.c
index 83d43cff4bd7..acba06618080 100644
--- a/arch/arm/mach-orion5x/kurobox_pro-setup.c
+++ b/arch/arm/mach-orion5x/kurobox_pro-setup.c
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/mach-orion5x/kurobox_pro-setup.c
  *
  * Maintainer: Ronen Shitrit <rshitrit@marvell.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 #include <linux/gpio.h>
 #include <linux/kernel.h>
diff --git a/arch/arm/mach-orion5x/ls_hgl-setup.c b/arch/arm/mach-orion5x/ls_hgl-setup.c
index 47ba6e0502f5..af07f617465f 100644
--- a/arch/arm/mach-orion5x/ls_hgl-setup.c
+++ b/arch/arm/mach-orion5x/ls_hgl-setup.c
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/mach-orion5x/ls_hgl-setup.c
  *
  * Maintainer: Zhu Qingsen <zhuqs@cn.fujitsu.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #include <linux/kernel.h>
diff --git a/arch/arm/mach-orion5x/mpp.c b/arch/arm/mach-orion5x/mpp.c
index 19ef18594415..b9855dce6ba0 100644
--- a/arch/arm/mach-orion5x/mpp.c
+++ b/arch/arm/mach-orion5x/mpp.c
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/mach-orion5x/mpp.c
  *
  * MPP functions for Marvell Orion 5x SoCs
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #include <linux/kernel.h>
diff --git a/arch/arm/mach-orion5x/net2big-setup.c b/arch/arm/mach-orion5x/net2big-setup.c
index bf6be4cfd238..695cc683cd83 100644
--- a/arch/arm/mach-orion5x/net2big-setup.c
+++ b/arch/arm/mach-orion5x/net2big-setup.c
@@ -1,13 +1,10 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/mach-orion5x/net2big-setup.c
  *
  * LaCie 2Big Network NAS setup
  *
  * Copyright (C) 2009 Simon Guinot <sguinot@lacie.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #include <linux/kernel.h>
@@ -432,4 +429,3 @@ MACHINE_START(NET2BIG, "LaCie 2Big Network")
 	.fixup		= tag_fixup_mem32,
 	.restart	= orion5x_restart,
 MACHINE_END
-
diff --git a/arch/arm/mach-orion5x/orion5x.h b/arch/arm/mach-orion5x/orion5x.h
index 2b66120fba86..26f1ccb8cb28 100644
--- a/arch/arm/mach-orion5x/orion5x.h
+++ b/arch/arm/mach-orion5x/orion5x.h
@@ -1,12 +1,9 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * Generic definitions of Orion SoC flavors:
  *  Orion-1, Orion-VoIP, Orion-NAS, Orion-2, and Orion-1-90.
  *
  * Maintainer: Tzachi Perelstein <tzachi@marvell.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #ifndef __ASM_ARCH_ORION5X_H
diff --git a/arch/arm/mach-orion5x/pci.c b/arch/arm/mach-orion5x/pci.c
index 76951bfbacf5..888fdc9099c5 100644
--- a/arch/arm/mach-orion5x/pci.c
+++ b/arch/arm/mach-orion5x/pci.c
@@ -1,13 +1,10 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/mach-orion5x/pci.c
  *
  * PCI and PCIe functions for Marvell Orion System On Chip
  *
  * Maintainer: Tzachi Perelstein <tzachi@marvell.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #include <linux/kernel.h>
@@ -142,6 +139,7 @@ static struct pci_ops pcie_ops = {
 static int __init pcie_setup(struct pci_sys_data *sys)
 {
 	struct resource *res;
+	struct resource realio;
 	int dev;
 
 	/*
@@ -164,7 +162,9 @@ static int __init pcie_setup(struct pci_sys_data *sys)
 		pcie_ops.read = pcie_rd_conf_wa;
 	}
 
-	pci_ioremap_io(sys->busnr * SZ_64K, ORION5X_PCIE_IO_PHYS_BASE);
+	realio.start = sys->busnr * SZ_64K;
+	realio.end = realio.start + SZ_64K - 1;
+	pci_remap_iospace(&realio, ORION5X_PCIE_IO_PHYS_BASE);
 
 	/*
 	 * Request resources.
@@ -466,6 +466,7 @@ static void __init orion5x_setup_pci_wins(void)
 static int __init pci_setup(struct pci_sys_data *sys)
 {
 	struct resource *res;
+	struct resource realio;
 
 	/*
 	 * Point PCI unit MBUS decode windows to DRAM space.
@@ -482,7 +483,9 @@ static int __init pci_setup(struct pci_sys_data *sys)
 	 */
 	orion5x_setbits(PCI_CMD, PCI_CMD_HOST_REORDER);
 
-	pci_ioremap_io(sys->busnr * SZ_64K, ORION5X_PCI_IO_PHYS_BASE);
+	realio.start = sys->busnr * SZ_64K;
+	realio.end = realio.start + SZ_64K - 1;
+	pci_remap_iospace(&realio, ORION5X_PCI_IO_PHYS_BASE);
 
 	/*
 	 * Request resources
@@ -509,14 +512,20 @@ static int __init pci_setup(struct pci_sys_data *sys)
 /*****************************************************************************
  * General PCIe + PCI
  ****************************************************************************/
+
+/*
+ * The root complex has a hardwired class of PCI_CLASS_MEMORY_OTHER, when it
+ * is operating as a root complex this needs to be switched to
+ * PCI_CLASS_BRIDGE_HOST or Linux will errantly try to process the BAR's on
+ * the device. Decoding setup is handled by the orion code.
+ */
 static void rc_pci_fixup(struct pci_dev *dev)
 {
-	/*
-	 * Prevent enumeration of root complex.
-	 */
 	if (dev->bus->parent == NULL && dev->devfn == 0) {
 		int i;
 
+		dev->class &= 0xff;
+		dev->class |= PCI_CLASS_BRIDGE_HOST << 8;
 		for (i = 0; i < DEVICE_COUNT_RESOURCE; i++) {
 			dev->resource[i].start = 0;
 			dev->resource[i].end   = 0;
diff --git a/arch/arm/mach-orion5x/rd88f5181l-fxo-setup.c b/arch/arm/mach-orion5x/rd88f5181l-fxo-setup.c
index c65ab7db36ad..432fc8357d9e 100644
--- a/arch/arm/mach-orion5x/rd88f5181l-fxo-setup.c
+++ b/arch/arm/mach-orion5x/rd88f5181l-fxo-setup.c
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/mach-orion5x/rd88f5181l-fxo-setup.c
  *
  * Marvell Orion-VoIP FXO Reference Design Setup
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 #include <linux/gpio.h>
 #include <linux/kernel.h>
diff --git a/arch/arm/mach-orion5x/rd88f5181l-ge-setup.c b/arch/arm/mach-orion5x/rd88f5181l-ge-setup.c
index 76b8138d9d79..d4b1a9c3cd36 100644
--- a/arch/arm/mach-orion5x/rd88f5181l-ge-setup.c
+++ b/arch/arm/mach-orion5x/rd88f5181l-ge-setup.c
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/mach-orion5x/rd88f5181l-ge-setup.c
  *
  * Marvell Orion-VoIP GE Reference Design Setup
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 #include <linux/gpio.h>
 #include <linux/kernel.h>
diff --git a/arch/arm/mach-orion5x/rd88f5182-setup.c b/arch/arm/mach-orion5x/rd88f5182-setup.c
index fe3e67c81fb8..6ffcfc6445e2 100644
--- a/arch/arm/mach-orion5x/rd88f5182-setup.c
+++ b/arch/arm/mach-orion5x/rd88f5182-setup.c
@@ -1,13 +1,10 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/mach-orion5x/rd88f5182-setup.c
  *
  * Marvell Orion-NAS Reference Design Setup
  *
  * Maintainer: Ronen Shitrit <rshitrit@marvell.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 #include <linux/gpio.h>
 #include <linux/kernel.h>
diff --git a/arch/arm/mach-orion5x/rd88f6183ap-ge-setup.c b/arch/arm/mach-orion5x/rd88f6183ap-ge-setup.c
index 5f388a1ed1e4..93f74fd6b4da 100644
--- a/arch/arm/mach-orion5x/rd88f6183ap-ge-setup.c
+++ b/arch/arm/mach-orion5x/rd88f6183ap-ge-setup.c
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/mach-orion5x/rd88f6183-ap-ge-setup.c
  *
  * Marvell Orion-1-90 AP GE Reference Design Setup
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 #include <linux/gpio.h>
 #include <linux/kernel.h>
diff --git a/arch/arm/mach-orion5x/ts78xx-setup.c b/arch/arm/mach-orion5x/ts78xx-setup.c
index a39764faf2a0..af810e7ccd79 100644
--- a/arch/arm/mach-orion5x/ts78xx-setup.c
+++ b/arch/arm/mach-orion5x/ts78xx-setup.c
@@ -1,11 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/mach-orion5x/ts78xx-setup.c
  *
  * Maintainer: Alexander Clouter <alex@digriz.org.uk>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
diff --git a/arch/arm/mach-orion5x/wnr854t-setup.c b/arch/arm/mach-orion5x/wnr854t-setup.c
index 83589a28a491..e5f327054dd3 100644
--- a/arch/arm/mach-orion5x/wnr854t-setup.c
+++ b/arch/arm/mach-orion5x/wnr854t-setup.c
@@ -1,10 +1,5 @@
-/*
- * arch/arm/mach-orion5x/wnr854t-setup.c
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
+// SPDX-License-Identifier: GPL-2.0-only
+// arch/arm/mach-orion5x/wnr854t-setup.c
 #include <linux/gpio.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
diff --git a/arch/arm/mach-orion5x/wrt350n-v2-setup.c b/arch/arm/mach-orion5x/wrt350n-v2-setup.c
index cea08d4a2597..e6a2da6662df 100644
--- a/arch/arm/mach-orion5x/wrt350n-v2-setup.c
+++ b/arch/arm/mach-orion5x/wrt350n-v2-setup.c
@@ -1,10 +1,5 @@
-/*
- * arch/arm/mach-orion5x/wrt350n-v2-setup.c
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
+// SPDX-License-Identifier: GPL-2.0-only
+// arch/arm/mach-orion5x/wrt350n-v2-setup.c
 #include <linux/gpio.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
diff --git a/arch/arm/mach-oxnas/Kconfig b/arch/arm/mach-oxnas/Kconfig
index bee5f64c2e5f..a9ded7079268 100644
--- a/arch/arm/mach-oxnas/Kconfig
+++ b/arch/arm/mach-oxnas/Kconfig
@@ -1,6 +1,7 @@
 # SPDX-License-Identifier: GPL-2.0-only
 menuconfig ARCH_OXNAS
 	bool "Oxford Semiconductor OXNAS Family SoCs"
+	depends on (ARCH_MULTI_V5 && CPU_LITTLE_ENDIAN) || ARCH_MULTI_V6
 	select ARCH_HAS_RESET_CONTROLLER
 	select COMMON_CLK_OXNAS
 	select GPIOLIB
@@ -11,7 +12,6 @@ menuconfig ARCH_OXNAS
 	select RESET_OXNAS
 	select VERSATILE_FPGA_IRQ
 	select PINCTRL
-	depends on ARCH_MULTI_V5 || ARCH_MULTI_V6
 	help
 	  Support for OxNas SoC family developed by Oxford Semiconductor.
 
diff --git a/arch/arm/mach-pxa/Kconfig b/arch/arm/mach-pxa/Kconfig
index f7520a6cc7d4..b90d98bae68d 100644
--- a/arch/arm/mach-pxa/Kconfig
+++ b/arch/arm/mach-pxa/Kconfig
@@ -1,4 +1,19 @@
 # SPDX-License-Identifier: GPL-2.0-only
+menuconfig ARCH_PXA
+	bool "PXA2xx/PXA3xx-based"
+	depends on ARCH_MULTI_V5
+	depends on CPU_LITTLE_ENDIAN
+	select ARM_CPU_SUSPEND if PM
+	select CLKSRC_PXA
+	select CLKSRC_MMIO
+	select TIMER_OF
+	select CPU_XSCALE if !CPU_XSC3
+	select GPIO_PXA
+	select GPIOLIB
+	select PLAT_PXA
+	help
+	  Support for Intel/Marvell's PXA2xx/PXA3xx processor line.
+
 if ARCH_PXA
 
 menu "Intel PXA2xx/PXA3xx Implementations"
@@ -39,14 +54,18 @@ config MACH_PXA3XX_DT
 	  the device tree. Needn't select any other machine while
 	  MACH_PXA3XX_DT is enabled.
 
+if ATAGS
+
 config ARCH_LUBBOCK
 	bool "Intel DBPXA250 Development Platform (aka Lubbock)"
+	depends on UNUSED_BOARD_FILES
 	select GPIO_REG
 	select PXA25x
 	select SA1111
 
 config MACH_MAINSTONE
 	bool "Intel HCDDBBVA0 Development Platform (aka Mainstone)"
+	depends on UNUSED_BOARD_FILES
 	select GPIO_REG
 	select PXA27x
 
@@ -56,23 +75,27 @@ config MACH_ZYLONITE
 
 config MACH_ZYLONITE300
 	bool "PXA3xx Development Platform (aka Zylonite) PXA300/310"
+	depends on UNUSED_BOARD_FILES
 	select CPU_PXA300
 	select CPU_PXA310
 	select MACH_ZYLONITE
 
 config MACH_ZYLONITE320
 	bool "PXA3xx Development Platform (aka Zylonite) PXA320"
+	depends on UNUSED_BOARD_FILES
 	select CPU_PXA320
 	select MACH_ZYLONITE
 
 config MACH_LITTLETON
 	bool "PXA3xx Form Factor Platform (aka Littleton)"
+	depends on UNUSED_BOARD_FILES
 	select CPU_PXA300
 	select CPU_PXA310
 	select PXA3xx
 
 config MACH_TAVOREVB
 	bool "PXA930 Evaluation Board (aka TavorEVB)"
+	depends on UNUSED_BOARD_FILES
 	select CPU_PXA930
 	select CPU_PXA935
 	select PXA3xx
@@ -81,6 +104,7 @@ config MACH_TAVOREVB
 
 config MACH_SAAR
 	bool "PXA930 Handheld Platform (aka SAAR)"
+	depends on UNUSED_BOARD_FILES
 	select CPU_PXA930
 	select CPU_PXA935
 	select PXA3xx
@@ -91,10 +115,12 @@ comment "Third Party Dev Platforms (sorted by vendor name)"
 
 config ARCH_PXA_IDP
 	bool "Accelent Xscale IDP"
+	depends on UNUSED_BOARD_FILES
 	select PXA25x
 
 config ARCH_VIPER
 	bool "Arcom/Eurotech VIPER SBC"
+	depends on UNUSED_BOARD_FILES
 	select ARCOM_PCMCIA
 	select I2C_GPIO if I2C=y
 	select ISA
@@ -102,17 +128,20 @@ config ARCH_VIPER
 
 config MACH_ARCOM_ZEUS
 	bool "Arcom/Eurotech ZEUS SBC"
+	depends on UNUSED_BOARD_FILES
 	select ARCOM_PCMCIA
 	select ISA
 	select PXA27x
 
 config MACH_BALLOON3
 	bool "Balloon 3 board"
+	depends on UNUSED_BOARD_FILES
 	select IWMMXT
 	select PXA27x
 
 config MACH_CSB726
 	bool "Enable Cogent CSB726 System On a Module"
+	depends on UNUSED_BOARD_FILES
 	select IWMMXT
 	select PXA27x
 	help
@@ -121,16 +150,19 @@ config MACH_CSB726
 
 config CSB726_CSB701
 	bool "Enable support for CSB701 baseboard"
+	depends on UNUSED_BOARD_FILES
 	depends on MACH_CSB726
 
 config MACH_CM_X300
 	bool "CompuLab CM-X300 modules"
+	depends on UNUSED_BOARD_FILES
 	select CPU_PXA300
 	select CPU_PXA310
 	select PXA3xx
 
 config MACH_CAPC7117
 	bool "Embedian CAPC-7117 evaluation kit based on the MXM-8x10 CoM"
+	depends on UNUSED_BOARD_FILES
 	select CPU_PXA320
 	select PXA3xx
 
@@ -153,18 +185,9 @@ config GUMSTIX_AM300EPD
 
 endchoice
 
-config MACH_INTELMOTE2
-	bool "Intel Mote 2 Platform"
-	select IWMMXT
-	select PXA27x
-
-config MACH_STARGATE2
-	bool "Intel Stargate 2 Platform"
-	select IWMMXT
-	select PXA27x
-
 config MACH_XCEP
 	bool "Iskratel Electronics XCEP"
+	depends on UNUSED_BOARD_FILES
 	select MTD
 	select MTD_CFI
 	select MTD_CFI_INTELEXT
@@ -176,6 +199,7 @@ config MACH_XCEP
 
 config TRIZEPS_PXA
 	bool "PXA based Keith und Koep Trizeps DIMM-Modules"
+	depends on UNUSED_BOARD_FILES
 
 config MACH_TRIZEPS4
 	bool "Keith und Koep Trizeps4 DIMM-Module"
@@ -217,15 +241,18 @@ config TRIZEPS_PCMCIA
 
 config MACH_LOGICPD_PXA270
 	bool "LogicPD PXA270 Card Engine Development Platform"
+	depends on UNUSED_BOARD_FILES
 	select PXA27x
 
 config MACH_PCM027
 	bool "Phytec phyCORE-PXA270 CPU module (PCM-027)"
+	depends on UNUSED_BOARD_FILES
 	select IWMMXT
 	select PXA27x
 
 config MACH_PCM990_BASEBOARD
 	bool "PHYTEC PCM-990 development board"
+	depends on UNUSED_BOARD_FILES
 	depends on MACH_PCM027
 
 choice
@@ -245,30 +272,36 @@ endchoice
 
 config MACH_COLIBRI
 	bool "Toradex Colibri PXA270"
+	depends on UNUSED_BOARD_FILES
 	select PXA27x
 
 config MACH_COLIBRI_PXA270_INCOME
 	bool "Income s.r.o. PXA270 SBC"
+	depends on UNUSED_BOARD_FILES
 	depends on MACH_COLIBRI
 	select PXA27x
 
 config MACH_COLIBRI300
 	bool "Toradex Colibri PXA300/310"
+	depends on UNUSED_BOARD_FILES
 	select CPU_PXA300
 	select CPU_PXA310
 	select PXA3xx
 
 config MACH_COLIBRI320
 	bool "Toradex Colibri PXA320"
+	depends on UNUSED_BOARD_FILES
 	select CPU_PXA320
 	select PXA3xx
 
 config MACH_COLIBRI_EVALBOARD
 	bool "Toradex Colibri Evaluation Carrier Board support"
+	depends on UNUSED_BOARD_FILES
 	depends on MACH_COLIBRI || MACH_COLIBRI300 || MACH_COLIBRI320
 
 config MACH_VPAC270
 	bool "Voipac PXA270"
+	depends on UNUSED_BOARD_FILES
 	select HAVE_PATA_PLATFORM
 	select PXA27x
 	help
@@ -278,24 +311,29 @@ comment "End-user Products (sorted by vendor name)"
 
 config MACH_H4700
 	bool "HP iPAQ hx4700"
+	depends on UNUSED_BOARD_FILES
 	select IWMMXT
 	select PXA27x
 
 config MACH_H5000
 	bool "HP iPAQ h5000"
+	depends on UNUSED_BOARD_FILES
 	select PXA25x
 
 config MACH_HIMALAYA
 	bool "HTC Himalaya Support"
+	depends on UNUSED_BOARD_FILES
 	select CPU_PXA26x
 
 config MACH_MAGICIAN
 	bool "Enable HTC Magician Support"
+	depends on UNUSED_BOARD_FILES
 	select IWMMXT
 	select PXA27x
 
 config MACH_MIOA701
 	bool "Mitac Mio A701 Support"
+	depends on UNUSED_BOARD_FILES
 	select IWMMXT
 	select PXA27x
 	help
@@ -305,6 +343,7 @@ config MACH_MIOA701
 
 config PXA_EZX
 	bool "Motorola EZX Platform"
+	depends on UNUSED_BOARD_FILES
 	select IWMMXT
 	select PXA27x
 
@@ -340,16 +379,19 @@ config MACH_EZX_E2
 
 config MACH_MP900C
 	bool "Nec Mobilepro 900/c"
+	depends on UNUSED_BOARD_FILES
 	select PXA25x
 
 config ARCH_PXA_PALM
 	bool "PXA based Palm PDAs"
+	depends on UNUSED_BOARD_FILES
 
 config MACH_PALM27X
 	bool
 
 config MACH_PALMTE2
 	bool "Palm Tungsten|E2"
+	depends on UNUSED_BOARD_FILES
 	default y
 	depends on ARCH_PXA_PALM
 	select PXA25x
@@ -368,6 +410,7 @@ config MACH_PALMTC
 
 config MACH_PALMT5
 	bool "Palm Tungsten|T5"
+	depends on UNUSED_BOARD_FILES
 	default y
 	depends on ARCH_PXA_PALM
 	select IWMMXT
@@ -379,6 +422,7 @@ config MACH_PALMT5
 
 config MACH_PALMTX
 	bool "Palm T|X"
+	depends on UNUSED_BOARD_FILES
 	default y
 	depends on ARCH_PXA_PALM
 	select IWMMXT
@@ -390,6 +434,7 @@ config MACH_PALMTX
 
 config MACH_PALMZ72
 	bool "Palm Zire 72"
+	depends on UNUSED_BOARD_FILES
 	default y
 	depends on ARCH_PXA_PALM
 	select IWMMXT
@@ -401,6 +446,7 @@ config MACH_PALMZ72
 
 config MACH_PALMLD
 	bool "Palm LifeDrive"
+	depends on UNUSED_BOARD_FILES
 	default y
 	depends on ARCH_PXA_PALM
 	select IWMMXT
@@ -416,6 +462,7 @@ config PALM_TREO
 
 config MACH_CENTRO
 	bool "Palm Centro 685 (GSM)"
+	depends on UNUSED_BOARD_FILES
 	default y
 	depends on ARCH_PXA_PALM
 	select IWMMXT
@@ -428,6 +475,7 @@ config MACH_CENTRO
 
 config MACH_TREO680
 	bool "Palm Treo 680"
+	depends on UNUSED_BOARD_FILES
 	default y
 	depends on ARCH_PXA_PALM
 	select IWMMXT
@@ -460,24 +508,28 @@ config PXA_SHARPSL_DETECT_MACH_ID
 config MACH_POODLE
 	bool "Enable Sharp SL-5600 (Poodle) Support"
 	depends on PXA_SHARPSL
+	depends on UNUSED_BOARD_FILES
 	select PXA25x
 	select SHARP_LOCOMO
 
 config MACH_CORGI
 	bool "Enable Sharp SL-C700 (Corgi) Support"
 	depends on PXA_SHARPSL
+	depends on UNUSED_BOARD_FILES
 	select PXA25x
 	select PXA_SHARP_C7xx
 
 config MACH_SHEPHERD
 	bool "Enable Sharp SL-C750 (Shepherd) Support"
 	depends on PXA_SHARPSL
+	depends on UNUSED_BOARD_FILES
 	select PXA25x
 	select PXA_SHARP_C7xx
 
 config MACH_HUSKY
 	bool "Enable Sharp SL-C760 (Husky) Support"
 	depends on PXA_SHARPSL
+	depends on UNUSED_BOARD_FILES
 	select PXA25x
 	select PXA_SHARP_C7xx
 
@@ -504,6 +556,7 @@ config MACH_BORZOI
 
 config MACH_TOSA
 	bool "Enable Sharp SL-6000x (Tosa) Support"
+	depends on UNUSED_BOARD_FILES
 	depends on PXA_SHARPSL
 	select PXA25x
 
@@ -527,11 +580,13 @@ config TOSA_USE_EXT_KEYCODES
 
 config MACH_ICONTROL
 	bool "TMT iControl/SafeTCam based on the MXM-8x10 CoM"
+	depends on UNUSED_BOARD_FILES
 	select CPU_PXA320
 	select PXA3xx
 
 config ARCH_PXA_ESERIES
 	bool "PXA based Toshiba e-series PDAs"
+	depends on UNUSED_BOARD_FILES
 	select FB_W100
 	select FB
 	select PXA25x
@@ -586,7 +641,10 @@ config MACH_E800
 
 config MACH_ZIPIT2
 	bool "Zipit Z2 Handheld"
+	depends on UNUSED_BOARD_FILES
 	select PXA27x
+
+endif # ATAGS
 endmenu
 
 config PXA25x
diff --git a/arch/arm/mach-pxa/Makefile b/arch/arm/mach-pxa/Makefile
index 177abe584dd5..0aec36e67dc1 100644
--- a/arch/arm/mach-pxa/Makefile
+++ b/arch/arm/mach-pxa/Makefile
@@ -37,7 +37,8 @@ obj-$(CONFIG_MACH_SAAR)		+= saar.o
 obj-$(CONFIG_ARCH_PXA_IDP)	+= idp.o
 obj-$(CONFIG_ARCH_VIPER)	+= viper.o
 obj-$(CONFIG_MACH_ARCOM_ZEUS)	+= zeus.o
-obj-$(CONFIG_MACH_BALLOON3)	+= balloon3.o
+obj-$(CONFIG_ARCOM_PCMCIA)	+= viper-pcmcia.o
+obj-$(CONFIG_MACH_BALLOON3)	+= balloon3.o balloon3-pcmcia.o
 obj-$(CONFIG_MACH_CSB726)	+= csb726.o
 obj-$(CONFIG_CSB726_CSB701)	+= csb701.o
 obj-$(CONFIG_MACH_CM_X300)      += cm-x300.o
@@ -45,22 +46,22 @@ obj-$(CONFIG_MACH_CAPC7117)     += capc7117.o mxm8x10.o
 obj-$(CONFIG_ARCH_GUMSTIX)	+= gumstix.o
 obj-$(CONFIG_GUMSTIX_AM200EPD)	+= am200epd.o
 obj-$(CONFIG_GUMSTIX_AM300EPD)	+= am300epd.o
-obj-$(CONFIG_MACH_INTELMOTE2)	+= stargate2.o
-obj-$(CONFIG_MACH_STARGATE2)	+= stargate2.o
 obj-$(CONFIG_MACH_XCEP)         += xcep.o
 obj-$(CONFIG_MACH_TRIZEPS4)	+= trizeps4.o
+obj-$(CONFIG_TRIZEPS_PCMCIA)	+= trizeps4-pcmcia.o
 obj-$(CONFIG_MACH_LOGICPD_PXA270)	+= lpd270.o
 obj-$(CONFIG_MACH_PCM027)		+= pcm027.o
 obj-$(CONFIG_MACH_PCM990_BASEBOARD)	+= pcm990-baseboard.o
-obj-$(CONFIG_MACH_COLIBRI)			+= colibri-pxa270.o
+obj-$(CONFIG_MACH_COLIBRI)		+= colibri-pxa270.o colibri-pcmcia.o
 obj-$(CONFIG_MACH_COLIBRI_EVALBOARD)	+= colibri-evalboard.o
 obj-$(CONFIG_MACH_COLIBRI_PXA270_INCOME)	+= colibri-pxa270-income.o
 obj-$(CONFIG_MACH_COLIBRI300)	+= colibri-pxa3xx.o colibri-pxa300.o
-obj-$(CONFIG_MACH_COLIBRI320)	+= colibri-pxa3xx.o colibri-pxa320.o
-obj-$(CONFIG_MACH_VPAC270)	+= vpac270.o
+obj-$(CONFIG_MACH_COLIBRI320)	+= colibri-pxa3xx.o colibri-pxa320.o colibri-pcmcia.o
+obj-$(CONFIG_MACH_VPAC270)	+= vpac270.o vpac270-pcmcia.o
 
 # End-user Products
 obj-$(CONFIG_MACH_H4700)	+= hx4700.o
+obj-$(CONFIG_MACH_H4700)	+= hx4700-pcmcia.o
 obj-$(CONFIG_MACH_H5000)	+= h5000.o
 obj-$(CONFIG_MACH_HIMALAYA)	+= himalaya.o
 obj-$(CONFIG_MACH_MAGICIAN)	+= magician.o
@@ -68,12 +69,12 @@ obj-$(CONFIG_MACH_MIOA701)	+= mioa701.o mioa701_bootresume.o
 obj-$(CONFIG_PXA_EZX)           += ezx.o
 obj-$(CONFIG_MACH_MP900C)	+= mp900.o
 obj-$(CONFIG_MACH_PALMTE2)	+= palmte2.o
-obj-$(CONFIG_MACH_PALMTC)	+= palmtc.o
+obj-$(CONFIG_MACH_PALMTC)	+= palmtc.o palmtc-pcmcia.o
 obj-$(CONFIG_MACH_PALM27X)	+= palm27x.o
 obj-$(CONFIG_MACH_PALMT5)	+= palmt5.o
-obj-$(CONFIG_MACH_PALMTX)	+= palmtx.o
+obj-$(CONFIG_MACH_PALMTX)	+= palmtx.o palmtx-pcmcia.o
 obj-$(CONFIG_MACH_PALMZ72)	+= palmz72.o
-obj-$(CONFIG_MACH_PALMLD)	+= palmld.o
+obj-$(CONFIG_MACH_PALMLD)	+= palmld.o palmld-pcmcia.o
 obj-$(CONFIG_PALM_TREO)		+= palmtreo.o
 obj-$(CONFIG_PXA_SHARP_C7xx)	+= corgi.o sharpsl_pm.o corgi_pm.o
 obj-$(CONFIG_PXA_SHARP_Cxx00)	+= spitz.o sharpsl_pm.o spitz_pm.o
@@ -81,6 +82,7 @@ obj-$(CONFIG_MACH_POODLE)	+= poodle.o
 obj-$(CONFIG_MACH_TOSA)		+= tosa.o
 obj-$(CONFIG_MACH_ICONTROL)     += icontrol.o mxm8x10.o
 obj-$(CONFIG_ARCH_PXA_ESERIES)	+= eseries.o
+obj-$(CONFIG_MACH_E740)		+= e740-pcmcia.o
 obj-$(CONFIG_MACH_ZIPIT2)	+= z2.o
 
 obj-$(CONFIG_PXA_SYSTEMS_CPLDS)	+= pxa_cplds_irqs.o
diff --git a/arch/arm/mach-pxa/Makefile.boot b/arch/arm/mach-pxa/Makefile.boot
deleted file mode 100644
index bb6e353ecf06..000000000000
--- a/arch/arm/mach-pxa/Makefile.boot
+++ /dev/null
@@ -1,3 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0-only
-   zreladdr-y	+= 0xa0008000
-
diff --git a/arch/arm/mach-pxa/include/mach/addr-map.h b/arch/arm/mach-pxa/addr-map.h
index 93cfe7dbfec6..93cfe7dbfec6 100644
--- a/arch/arm/mach-pxa/include/mach/addr-map.h
+++ b/arch/arm/mach-pxa/addr-map.h
diff --git a/arch/arm/mach-pxa/am300epd.c b/arch/arm/mach-pxa/am300epd.c
index 17d08abeeb17..4b55bc89db8f 100644
--- a/arch/arm/mach-pxa/am300epd.c
+++ b/arch/arm/mach-pxa/am300epd.c
@@ -30,7 +30,7 @@
 
 #include "gumstix.h"
 #include "mfp-pxa25x.h"
-#include <mach/irqs.h>
+#include "irqs.h"
 #include <linux/platform_data/video-pxafb.h>
 
 #include "generic.h"
diff --git a/arch/arm/mach-pxa/balloon3-pcmcia.c b/arch/arm/mach-pxa/balloon3-pcmcia.c
new file mode 100644
index 000000000000..6a27b76cc603
--- /dev/null
+++ b/arch/arm/mach-pxa/balloon3-pcmcia.c
@@ -0,0 +1,137 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * linux/drivers/pcmcia/pxa2xx_balloon3.c
+ *
+ * Balloon3 PCMCIA specific routines.
+ *
+ *  Author:	Nick Bane
+ *  Created:	June, 2006
+ *  Copyright:	Toby Churchill Ltd
+ *  Derived from pxa2xx_mainstone.c, by Nico Pitre
+ *
+ * Various modification by Marek Vasut <marek.vasut@gmail.com>
+ */
+
+#include <linux/module.h>
+#include <linux/gpio.h>
+#include <linux/errno.h>
+#include <linux/interrupt.h>
+#include <linux/platform_device.h>
+#include <linux/irq.h>
+#include <linux/io.h>
+
+#include "balloon3.h"
+
+#include <asm/mach-types.h>
+
+#include <pcmcia/soc_common.h>
+
+static int balloon3_pcmcia_hw_init(struct soc_pcmcia_socket *skt)
+{
+	uint16_t ver;
+
+	ver = __raw_readw(BALLOON3_FPGA_VER);
+	if (ver < 0x4f08)
+		pr_warn("The FPGA code, version 0x%04x, is too old. "
+			"PCMCIA/CF support might be broken in this version!",
+			ver);
+
+	skt->socket.pci_irq = BALLOON3_BP_CF_NRDY_IRQ;
+	skt->stat[SOC_STAT_CD].gpio = BALLOON3_GPIO_S0_CD;
+	skt->stat[SOC_STAT_CD].name = "PCMCIA0 CD";
+	skt->stat[SOC_STAT_BVD1].irq = BALLOON3_BP_NSTSCHG_IRQ;
+	skt->stat[SOC_STAT_BVD1].name = "PCMCIA0 STSCHG";
+
+	return 0;
+}
+
+static unsigned long balloon3_pcmcia_status[2] = {
+	BALLOON3_CF_nSTSCHG_BVD1,
+	BALLOON3_CF_nSTSCHG_BVD1
+};
+
+static void balloon3_pcmcia_socket_state(struct soc_pcmcia_socket *skt,
+				    struct pcmcia_state *state)
+{
+	uint16_t status;
+	int flip;
+
+	/* This actually reads the STATUS register */
+	status = __raw_readw(BALLOON3_CF_STATUS_REG);
+	flip = (status ^ balloon3_pcmcia_status[skt->nr])
+		& BALLOON3_CF_nSTSCHG_BVD1;
+	/*
+	 * Workaround for STSCHG which can't be deasserted:
+	 * We therefore disable/enable corresponding IRQs
+	 * as needed to avoid IRQ locks.
+	 */
+	if (flip) {
+		balloon3_pcmcia_status[skt->nr] = status;
+		if (status & BALLOON3_CF_nSTSCHG_BVD1)
+			enable_irq(BALLOON3_BP_NSTSCHG_IRQ);
+		else
+			disable_irq(BALLOON3_BP_NSTSCHG_IRQ);
+	}
+
+	state->ready	= !!(status & BALLOON3_CF_nIRQ);
+	state->bvd1	= !!(status & BALLOON3_CF_nSTSCHG_BVD1);
+	state->bvd2	= 0;	/* not available */
+	state->vs_3v	= 1;	/* Always true its a CF card */
+	state->vs_Xv	= 0;	/* not available */
+}
+
+static int balloon3_pcmcia_configure_socket(struct soc_pcmcia_socket *skt,
+				       const socket_state_t *state)
+{
+	__raw_writew(BALLOON3_CF_RESET, BALLOON3_CF_CONTROL_REG +
+			((state->flags & SS_RESET) ?
+			BALLOON3_FPGA_SETnCLR : 0));
+	return 0;
+}
+
+static struct pcmcia_low_level balloon3_pcmcia_ops = {
+	.owner			= THIS_MODULE,
+	.hw_init		= balloon3_pcmcia_hw_init,
+	.socket_state		= balloon3_pcmcia_socket_state,
+	.configure_socket	= balloon3_pcmcia_configure_socket,
+	.first			= 0,
+	.nr			= 1,
+};
+
+static struct platform_device *balloon3_pcmcia_device;
+
+static int __init balloon3_pcmcia_init(void)
+{
+	int ret;
+
+	if (!machine_is_balloon3())
+		return -ENODEV;
+
+	balloon3_pcmcia_device = platform_device_alloc("pxa2xx-pcmcia", -1);
+	if (!balloon3_pcmcia_device)
+		return -ENOMEM;
+
+	ret = platform_device_add_data(balloon3_pcmcia_device,
+			&balloon3_pcmcia_ops, sizeof(balloon3_pcmcia_ops));
+
+	if (!ret)
+		ret = platform_device_add(balloon3_pcmcia_device);
+
+	if (ret)
+		platform_device_put(balloon3_pcmcia_device);
+
+	return ret;
+}
+
+static void __exit balloon3_pcmcia_exit(void)
+{
+	platform_device_unregister(balloon3_pcmcia_device);
+}
+
+module_init(balloon3_pcmcia_init);
+module_exit(balloon3_pcmcia_exit);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Nick Bane <nick@cecomputing.co.uk>");
+MODULE_ALIAS("platform:pxa2xx-pcmcia");
+MODULE_DESCRIPTION("Balloon3 board CF/PCMCIA driver");
diff --git a/arch/arm/mach-pxa/balloon3.c b/arch/arm/mach-pxa/balloon3.c
index 26140249c784..896d47d9a8dc 100644
--- a/arch/arm/mach-pxa/balloon3.c
+++ b/arch/arm/mach-pxa/balloon3.c
@@ -40,8 +40,8 @@
 #include <asm/mach/flash.h>
 
 #include "pxa27x.h"
-#include <mach/balloon3.h>
-#include <mach/audio.h>
+#include "balloon3.h"
+#include <linux/platform_data/asoc-pxa.h>
 #include <linux/platform_data/video-pxafb.h>
 #include <linux/platform_data/mmc-pxamci.h>
 #include "udc.h"
diff --git a/arch/arm/mach-pxa/include/mach/balloon3.h b/arch/arm/mach-pxa/balloon3.h
index 04f3639c4082..04f3639c4082 100644
--- a/arch/arm/mach-pxa/include/mach/balloon3.h
+++ b/arch/arm/mach-pxa/balloon3.h
diff --git a/arch/arm/mach-pxa/cm-x300.c b/arch/arm/mach-pxa/cm-x300.c
index 2e35354b61f5..01f364a66446 100644
--- a/arch/arm/mach-pxa/cm-x300.c
+++ b/arch/arm/mach-pxa/cm-x300.c
@@ -40,6 +40,8 @@
 #include <linux/spi/spi_gpio.h>
 #include <linux/spi/tdo24m.h>
 
+#include <linux/soc/pxa/cpu.h>
+
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
 #include <asm/setup.h>
@@ -51,7 +53,7 @@
 #include <linux/platform_data/mmc-pxamci.h>
 #include <linux/platform_data/usb-ohci-pxa27x.h>
 #include <linux/platform_data/mtd-nand-pxa3xx.h>
-#include <mach/audio.h>
+#include <linux/platform_data/asoc-pxa.h>
 #include <linux/platform_data/usb-pxa3xx-ulpi.h>
 
 #include <asm/mach/map.h>
@@ -354,13 +356,13 @@ static struct platform_device cm_x300_spi_gpio = {
 static struct gpiod_lookup_table cm_x300_spi_gpiod_table = {
 	.dev_id         = "spi_gpio",
 	.table          = {
-		GPIO_LOOKUP("gpio-pxa", GPIO_LCD_SCL,
+		GPIO_LOOKUP("pca9555.1", GPIO_LCD_SCL - GPIO_LCD_BASE,
 			    "sck", GPIO_ACTIVE_HIGH),
-		GPIO_LOOKUP("gpio-pxa", GPIO_LCD_DIN,
+		GPIO_LOOKUP("pca9555.1", GPIO_LCD_DIN - GPIO_LCD_BASE,
 			    "mosi", GPIO_ACTIVE_HIGH),
-		GPIO_LOOKUP("gpio-pxa", GPIO_LCD_DOUT,
+		GPIO_LOOKUP("pca9555.1", GPIO_LCD_DOUT - GPIO_LCD_BASE,
 			    "miso", GPIO_ACTIVE_HIGH),
-		GPIO_LOOKUP("gpio-pxa", GPIO_LCD_CS,
+		GPIO_LOOKUP("pca9555.1", GPIO_LCD_CS - GPIO_LCD_BASE,
 			    "cs", GPIO_ACTIVE_HIGH),
 		{ },
 	},
diff --git a/arch/arm/mach-pxa/colibri-evalboard.c b/arch/arm/mach-pxa/colibri-evalboard.c
index b9c173ede891..b62af07b8f96 100644
--- a/arch/arm/mach-pxa/colibri-evalboard.c
+++ b/arch/arm/mach-pxa/colibri-evalboard.c
@@ -13,7 +13,6 @@
 #include <linux/interrupt.h>
 #include <linux/gpio/machine.h>
 #include <asm/mach-types.h>
-#include <mach/hardware.h>
 #include <asm/mach/arch.h>
 #include <linux/i2c.h>
 #include <linux/platform_data/i2c-pxa.h>
diff --git a/arch/arm/mach-pxa/colibri-pcmcia.c b/arch/arm/mach-pxa/colibri-pcmcia.c
new file mode 100644
index 000000000000..9da7b478e5eb
--- /dev/null
+++ b/arch/arm/mach-pxa/colibri-pcmcia.c
@@ -0,0 +1,165 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * linux/drivers/pcmcia/pxa2xx_colibri.c
+ *
+ * Driver for Toradex Colibri PXA270 CF socket
+ *
+ * Copyright (C) 2010 Marek Vasut <marek.vasut@gmail.com>
+ */
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/delay.h>
+#include <linux/gpio.h>
+
+#include <asm/mach-types.h>
+
+#include <pcmcia/soc_common.h>
+
+#define	COLIBRI270_RESET_GPIO	53
+#define	COLIBRI270_PPEN_GPIO	107
+#define	COLIBRI270_BVD1_GPIO	83
+#define	COLIBRI270_BVD2_GPIO	82
+#define	COLIBRI270_DETECT_GPIO	84
+#define	COLIBRI270_READY_GPIO	1
+
+#define	COLIBRI320_RESET_GPIO	77
+#define	COLIBRI320_PPEN_GPIO	57
+#define	COLIBRI320_BVD1_GPIO	53
+#define	COLIBRI320_BVD2_GPIO	79
+#define	COLIBRI320_DETECT_GPIO	81
+#define	COLIBRI320_READY_GPIO	29
+
+enum {
+	DETECT = 0,
+	READY = 1,
+	BVD1 = 2,
+	BVD2 = 3,
+	PPEN = 4,
+	RESET = 5,
+};
+
+/* Contents of this array are configured on-the-fly in init function */
+static struct gpio colibri_pcmcia_gpios[] = {
+	{ 0,	GPIOF_IN,	"PCMCIA Detect" },
+	{ 0,	GPIOF_IN,	"PCMCIA Ready" },
+	{ 0,	GPIOF_IN,	"PCMCIA BVD1" },
+	{ 0,	GPIOF_IN,	"PCMCIA BVD2" },
+	{ 0,	GPIOF_INIT_LOW,	"PCMCIA PPEN" },
+	{ 0,	GPIOF_INIT_HIGH,"PCMCIA Reset" },
+};
+
+static int colibri_pcmcia_hw_init(struct soc_pcmcia_socket *skt)
+{
+	int ret;
+
+	ret = gpio_request_array(colibri_pcmcia_gpios,
+				ARRAY_SIZE(colibri_pcmcia_gpios));
+	if (ret)
+		goto err1;
+
+	skt->socket.pci_irq = gpio_to_irq(colibri_pcmcia_gpios[READY].gpio);
+	skt->stat[SOC_STAT_CD].irq = gpio_to_irq(colibri_pcmcia_gpios[DETECT].gpio);
+	skt->stat[SOC_STAT_CD].name = "PCMCIA CD";
+
+err1:
+	return ret;
+}
+
+static void colibri_pcmcia_hw_shutdown(struct soc_pcmcia_socket *skt)
+{
+	gpio_free_array(colibri_pcmcia_gpios,
+			ARRAY_SIZE(colibri_pcmcia_gpios));
+}
+
+static void colibri_pcmcia_socket_state(struct soc_pcmcia_socket *skt,
+					struct pcmcia_state *state)
+{
+
+	state->detect = !!gpio_get_value(colibri_pcmcia_gpios[DETECT].gpio);
+	state->ready  = !!gpio_get_value(colibri_pcmcia_gpios[READY].gpio);
+	state->bvd1   = !!gpio_get_value(colibri_pcmcia_gpios[BVD1].gpio);
+	state->bvd2   = !!gpio_get_value(colibri_pcmcia_gpios[BVD2].gpio);
+	state->vs_3v  = 1;
+	state->vs_Xv  = 0;
+}
+
+static int
+colibri_pcmcia_configure_socket(struct soc_pcmcia_socket *skt,
+				const socket_state_t *state)
+{
+	gpio_set_value(colibri_pcmcia_gpios[PPEN].gpio,
+			!(state->Vcc == 33 && state->Vpp < 50));
+	gpio_set_value(colibri_pcmcia_gpios[RESET].gpio,
+			state->flags & SS_RESET);
+	return 0;
+}
+
+static struct pcmcia_low_level colibri_pcmcia_ops = {
+	.owner			= THIS_MODULE,
+
+	.first			= 0,
+	.nr			= 1,
+
+	.hw_init		= colibri_pcmcia_hw_init,
+	.hw_shutdown		= colibri_pcmcia_hw_shutdown,
+
+	.socket_state		= colibri_pcmcia_socket_state,
+	.configure_socket	= colibri_pcmcia_configure_socket,
+};
+
+static struct platform_device *colibri_pcmcia_device;
+
+static int __init colibri_pcmcia_init(void)
+{
+	int ret;
+
+	if (!machine_is_colibri() && !machine_is_colibri320())
+		return -ENODEV;
+
+	colibri_pcmcia_device = platform_device_alloc("pxa2xx-pcmcia", -1);
+	if (!colibri_pcmcia_device)
+		return -ENOMEM;
+
+	/* Colibri PXA270 */
+	if (machine_is_colibri()) {
+		colibri_pcmcia_gpios[RESET].gpio	= COLIBRI270_RESET_GPIO;
+		colibri_pcmcia_gpios[PPEN].gpio		= COLIBRI270_PPEN_GPIO;
+		colibri_pcmcia_gpios[BVD1].gpio		= COLIBRI270_BVD1_GPIO;
+		colibri_pcmcia_gpios[BVD2].gpio		= COLIBRI270_BVD2_GPIO;
+		colibri_pcmcia_gpios[DETECT].gpio	= COLIBRI270_DETECT_GPIO;
+		colibri_pcmcia_gpios[READY].gpio	= COLIBRI270_READY_GPIO;
+	/* Colibri PXA320 */
+	} else if (machine_is_colibri320()) {
+		colibri_pcmcia_gpios[RESET].gpio	= COLIBRI320_RESET_GPIO;
+		colibri_pcmcia_gpios[PPEN].gpio		= COLIBRI320_PPEN_GPIO;
+		colibri_pcmcia_gpios[BVD1].gpio		= COLIBRI320_BVD1_GPIO;
+		colibri_pcmcia_gpios[BVD2].gpio		= COLIBRI320_BVD2_GPIO;
+		colibri_pcmcia_gpios[DETECT].gpio	= COLIBRI320_DETECT_GPIO;
+		colibri_pcmcia_gpios[READY].gpio	= COLIBRI320_READY_GPIO;
+	}
+
+	ret = platform_device_add_data(colibri_pcmcia_device,
+		&colibri_pcmcia_ops, sizeof(colibri_pcmcia_ops));
+
+	if (!ret)
+		ret = platform_device_add(colibri_pcmcia_device);
+
+	if (ret)
+		platform_device_put(colibri_pcmcia_device);
+
+	return ret;
+}
+
+static void __exit colibri_pcmcia_exit(void)
+{
+	platform_device_unregister(colibri_pcmcia_device);
+}
+
+module_init(colibri_pcmcia_init);
+module_exit(colibri_pcmcia_exit);
+
+MODULE_AUTHOR("Marek Vasut <marek.vasut@gmail.com>");
+MODULE_DESCRIPTION("PCMCIA support for Toradex Colibri PXA270/PXA320");
+MODULE_ALIAS("platform:pxa2xx-pcmcia");
+MODULE_LICENSE("GPL");
diff --git a/arch/arm/mach-pxa/colibri-pxa270-income.c b/arch/arm/mach-pxa/colibri-pxa270-income.c
index e5879e8b0682..f6eaf464ca83 100644
--- a/arch/arm/mach-pxa/colibri-pxa270-income.c
+++ b/arch/arm/mach-pxa/colibri-pxa270-income.c
@@ -25,7 +25,6 @@
 #include <asm/irq.h>
 #include <asm/mach-types.h>
 
-#include <mach/hardware.h>
 #include <linux/platform_data/mmc-pxamci.h>
 #include <linux/platform_data/usb-ohci-pxa27x.h>
 #include "pxa27x.h"
diff --git a/arch/arm/mach-pxa/colibri-pxa270.c b/arch/arm/mach-pxa/colibri-pxa270.c
index 2f2cd2ae4187..5dc669752836 100644
--- a/arch/arm/mach-pxa/colibri-pxa270.c
+++ b/arch/arm/mach-pxa/colibri-pxa270.c
@@ -23,7 +23,7 @@
 #include <asm/mach-types.h>
 #include <linux/sizes.h>
 
-#include <mach/audio.h>
+#include <linux/platform_data/asoc-pxa.h>
 #include "colibri.h"
 #include "pxa27x.h"
 
diff --git a/arch/arm/mach-pxa/colibri-pxa300.c b/arch/arm/mach-pxa/colibri-pxa300.c
index 82052dfd96b6..11ca6c4795e7 100644
--- a/arch/arm/mach-pxa/colibri-pxa300.c
+++ b/arch/arm/mach-pxa/colibri-pxa300.c
@@ -13,6 +13,7 @@
 #include <linux/platform_device.h>
 #include <linux/gpio.h>
 #include <linux/interrupt.h>
+#include <linux/soc/pxa/cpu.h>
 
 #include <asm/mach-types.h>
 #include <linux/sizes.h>
@@ -23,7 +24,7 @@
 #include "colibri.h"
 #include <linux/platform_data/usb-ohci-pxa27x.h>
 #include <linux/platform_data/video-pxafb.h>
-#include <mach/audio.h>
+#include <linux/platform_data/asoc-pxa.h>
 
 #include "generic.h"
 #include "devices.h"
diff --git a/arch/arm/mach-pxa/colibri-pxa320.c b/arch/arm/mach-pxa/colibri-pxa320.c
index 35dd3adb7712..1a59056e181e 100644
--- a/arch/arm/mach-pxa/colibri-pxa320.c
+++ b/arch/arm/mach-pxa/colibri-pxa320.c
@@ -24,7 +24,7 @@
 #include "colibri.h"
 #include <linux/platform_data/video-pxafb.h>
 #include <linux/platform_data/usb-ohci-pxa27x.h>
-#include <mach/audio.h>
+#include <linux/platform_data/asoc-pxa.h>
 #include "pxa27x-udc.h"
 #include "udc.h"
 
diff --git a/arch/arm/mach-pxa/colibri-pxa3xx.c b/arch/arm/mach-pxa/colibri-pxa3xx.c
index 3cead80a2b37..77d6ef5fa42d 100644
--- a/arch/arm/mach-pxa/colibri-pxa3xx.c
+++ b/arch/arm/mach-pxa/colibri-pxa3xx.c
@@ -13,12 +13,11 @@
 #include <linux/gpio.h>
 #include <linux/etherdevice.h>
 #include <asm/mach-types.h>
-#include <mach/hardware.h>
 #include <linux/sizes.h>
 #include <asm/system_info.h>
 #include <asm/mach/arch.h>
 #include <asm/mach/irq.h>
-#include <mach/pxa3xx-regs.h>
+#include "pxa3xx-regs.h"
 #include "mfp-pxa300.h"
 #include "colibri.h"
 #include <linux/platform_data/mmc-pxamci.h>
diff --git a/arch/arm/mach-pxa/colibri.h b/arch/arm/mach-pxa/colibri.h
index 85525d49e321..01a46f36cc1f 100644
--- a/arch/arm/mach-pxa/colibri.h
+++ b/arch/arm/mach-pxa/colibri.h
@@ -3,7 +3,7 @@
 #define _COLIBRI_H_
 
 #include <net/ax88796.h>
-#include <mach/mfp.h>
+#include "mfp.h"
 
 /*
  * base board glue for PXA270 module
diff --git a/arch/arm/mach-pxa/corgi.c b/arch/arm/mach-pxa/corgi.c
index 593c7f793da5..5738496717e2 100644
--- a/arch/arm/mach-pxa/corgi.c
+++ b/arch/arm/mach-pxa/corgi.c
@@ -39,7 +39,6 @@
 #include <asm/setup.h>
 #include <asm/memory.h>
 #include <asm/mach-types.h>
-#include <mach/hardware.h>
 #include <asm/irq.h>
 
 #include <asm/mach/arch.h>
@@ -50,7 +49,7 @@
 #include <linux/platform_data/irda-pxaficp.h>
 #include <linux/platform_data/mmc-pxamci.h>
 #include "udc.h"
-#include <mach/corgi.h>
+#include "corgi.h"
 #include "sharpsl_pm.h"
 
 #include <asm/mach/sharpsl_param.h>
@@ -473,6 +472,25 @@ static struct platform_device corgiled_device = {
 	},
 };
 
+static struct gpiod_lookup_table corgi_audio_gpio_table = {
+	.dev_id = "corgi-audio",
+	.table = {
+		GPIO_LOOKUP("sharp-scoop",
+			    CORGI_GPIO_MUTE_L - CORGI_SCOOP_GPIO_BASE,
+			    "mute-l", GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP("sharp-scoop",
+			    CORGI_GPIO_MUTE_R - CORGI_SCOOP_GPIO_BASE,
+			    "mute-r", GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP("sharp-scoop",
+			    CORGI_GPIO_APM_ON - CORGI_SCOOP_GPIO_BASE,
+			    "apm-on", GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP("sharp-scoop",
+			    CORGI_GPIO_MIC_BIAS - CORGI_SCOOP_GPIO_BASE,
+			    "mic-bias", GPIO_ACTIVE_HIGH),
+		{ },
+	},
+};
+
 /*
  * Corgi Audio
  */
@@ -530,6 +548,16 @@ static struct pxa2xx_spi_controller corgi_spi_info = {
 	.num_chipselect	= 3,
 };
 
+static struct gpiod_lookup_table corgi_spi_gpio_table = {
+	.dev_id = "spi1",
+	.table = {
+		GPIO_LOOKUP_IDX("gpio-pxa", CORGI_GPIO_ADS7846_CS, "cs", 0, GPIO_ACTIVE_LOW),
+		GPIO_LOOKUP_IDX("gpio-pxa", CORGI_GPIO_LCDCON_CS, "cs", 1, GPIO_ACTIVE_LOW),
+		GPIO_LOOKUP_IDX("gpio-pxa", CORGI_GPIO_MAX1111_CS, "cs", 2, GPIO_ACTIVE_LOW),
+		{ },
+	},
+};
+
 static void corgi_wait_for_hsync(void)
 {
 	while (gpio_get_value(CORGI_GPIO_HSYNC))
@@ -548,10 +576,6 @@ static struct ads7846_platform_data corgi_ads7846_info = {
 	.wait_for_sync		= corgi_wait_for_hsync,
 };
 
-static struct pxa2xx_spi_chip corgi_ads7846_chip = {
-	.gpio_cs	= CORGI_GPIO_ADS7846_CS,
-};
-
 static void corgi_bl_kick_battery(void)
 {
 	void (*kick_batt)(void);
@@ -580,14 +604,6 @@ static struct corgi_lcd_platform_data corgi_lcdcon_info = {
 	.kick_battery		= corgi_bl_kick_battery,
 };
 
-static struct pxa2xx_spi_chip corgi_lcdcon_chip = {
-	.gpio_cs	= CORGI_GPIO_LCDCON_CS,
-};
-
-static struct pxa2xx_spi_chip corgi_max1111_chip = {
-	.gpio_cs	= CORGI_GPIO_MAX1111_CS,
-};
-
 static struct spi_board_info corgi_spi_devices[] = {
 	{
 		.modalias	= "ads7846",
@@ -595,7 +611,6 @@ static struct spi_board_info corgi_spi_devices[] = {
 		.bus_num	= 1,
 		.chip_select	= 0,
 		.platform_data	= &corgi_ads7846_info,
-		.controller_data= &corgi_ads7846_chip,
 		.irq		= PXA_GPIO_TO_IRQ(CORGI_GPIO_TP_INT),
 	}, {
 		.modalias	= "corgi-lcd",
@@ -603,18 +618,17 @@ static struct spi_board_info corgi_spi_devices[] = {
 		.bus_num	= 1,
 		.chip_select	= 1,
 		.platform_data	= &corgi_lcdcon_info,
-		.controller_data= &corgi_lcdcon_chip,
 	}, {
 		.modalias	= "max1111",
 		.max_speed_hz	= 450000,
 		.bus_num	= 1,
 		.chip_select	= 2,
-		.controller_data= &corgi_max1111_chip,
 	},
 };
 
 static void __init corgi_init_spi(void)
 {
+	gpiod_add_lookup_table(&corgi_spi_gpio_table);
 	pxa2xx_set_spi_info(1, &corgi_spi_info);
 	gpiod_add_lookup_table(&corgi_lcdcon_gpio_table);
 	spi_register_board_info(ARRAY_AND_SIZE(corgi_spi_devices));
@@ -749,6 +763,7 @@ static void __init corgi_init(void)
 
  	pxa_set_udc_info(&udc_info);
 	gpiod_add_lookup_table(&corgi_mci_gpio_table);
+	gpiod_add_lookup_table(&corgi_audio_gpio_table);
 	pxa_set_mci_info(&corgi_mci_platform_data);
 	pxa_set_ficp_info(&corgi_ficp_platform_data);
 	pxa_set_i2c_info(NULL);
diff --git a/arch/arm/mach-pxa/include/mach/corgi.h b/arch/arm/mach-pxa/corgi.h
index b565ca7b8cda..b565ca7b8cda 100644
--- a/arch/arm/mach-pxa/include/mach/corgi.h
+++ b/arch/arm/mach-pxa/corgi.h
diff --git a/arch/arm/mach-pxa/corgi_pm.c b/arch/arm/mach-pxa/corgi_pm.c
index 092dcb9fced5..555a5c1afd96 100644
--- a/arch/arm/mach-pxa/corgi_pm.c
+++ b/arch/arm/mach-pxa/corgi_pm.c
@@ -19,10 +19,9 @@
 
 #include <asm/irq.h>
 #include <asm/mach-types.h>
-#include <mach/hardware.h>
 
-#include <mach/corgi.h>
-#include <mach/pxa2xx-regs.h>
+#include "corgi.h"
+#include "pxa2xx-regs.h"
 #include "sharpsl_pm.h"
 
 #include "generic.h"
diff --git a/arch/arm/mach-pxa/csb726.c b/arch/arm/mach-pxa/csb726.c
index 98fcdc6e2944..410b1af87d55 100644
--- a/arch/arm/mach-pxa/csb726.c
+++ b/arch/arm/mach-pxa/csb726.c
@@ -17,12 +17,13 @@
 
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
+
 #include "csb726.h"
 #include "pxa27x.h"
 #include <linux/platform_data/mmc-pxamci.h>
 #include <linux/platform_data/usb-ohci-pxa27x.h>
-#include <mach/audio.h>
-#include <mach/smemc.h>
+#include <linux/platform_data/asoc-pxa.h>
+#include "smemc.h"
 
 #include "generic.h"
 #include "devices.h"
diff --git a/arch/arm/mach-pxa/csb726.h b/arch/arm/mach-pxa/csb726.h
index 30d7cf926b84..628928743bd5 100644
--- a/arch/arm/mach-pxa/csb726.h
+++ b/arch/arm/mach-pxa/csb726.h
@@ -7,7 +7,7 @@
 #ifndef CSB726_H
 #define CSB726_H
 
-#include <mach/irqs.h> /* PXA_GPIO_TO_IRQ */
+#include "irqs.h" /* PXA_GPIO_TO_IRQ */
 
 #define CSB726_GPIO_IRQ_LAN	52
 #define CSB726_GPIO_IRQ_SM501	53
diff --git a/arch/arm/mach-pxa/devices.c b/arch/arm/mach-pxa/devices.c
index 09b8495f3fd9..a7b92dd1ca9e 100644
--- a/arch/arm/mach-pxa/devices.c
+++ b/arch/arm/mach-pxa/devices.c
@@ -9,21 +9,23 @@
 #include <linux/dmaengine.h>
 #include <linux/spi/pxa2xx_spi.h>
 #include <linux/platform_data/i2c-pxa.h>
+#include <linux/soc/pxa/cpu.h>
 
 #include "udc.h"
 #include <linux/platform_data/usb-pxa3xx-ulpi.h>
 #include <linux/platform_data/video-pxafb.h>
 #include <linux/platform_data/mmc-pxamci.h>
 #include <linux/platform_data/irda-pxaficp.h>
-#include <mach/irqs.h>
+#include "irqs.h"
 #include <linux/platform_data/usb-ohci-pxa27x.h>
 #include <linux/platform_data/keypad-pxa27x.h>
 #include <linux/platform_data/media/camera-pxa.h>
-#include <mach/audio.h>
-#include <mach/hardware.h>
+#include <linux/platform_data/asoc-pxa.h>
 #include <linux/platform_data/mmp_dma.h>
 #include <linux/platform_data/mtd-nand-pxa3xx.h>
 
+#include "regs-ost.h"
+#include "reset.h"
 #include "devices.h"
 #include "generic.h"
 
@@ -1118,3 +1120,12 @@ void __init pxa2xx_set_dmac_info(struct mmp_dma_platdata *dma_pdata)
 {
 	pxa_register_device(&pxa2xx_pxa_dma, dma_pdata);
 }
+
+void __init pxa_register_wdt(unsigned int reset_status)
+{
+	struct resource res = DEFINE_RES_MEM(OST_PHYS, OST_LEN);
+
+	reset_status &= RESET_STATUS_WATCHDOG;
+	platform_device_register_resndata(NULL, "sa1100_wdt", -1, &res, 1,
+					  &reset_status, sizeof(reset_status));
+}
diff --git a/arch/arm/mach-pxa/e740-pcmcia.c b/arch/arm/mach-pxa/e740-pcmcia.c
new file mode 100644
index 000000000000..11a2c5d42920
--- /dev/null
+++ b/arch/arm/mach-pxa/e740-pcmcia.c
@@ -0,0 +1,127 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Toshiba e740 PCMCIA specific routines.
+ *
+ * (c) 2004 Ian Molton <spyro@f2s.com>
+ */
+
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/errno.h>
+#include <linux/gpio.h>
+#include <linux/interrupt.h>
+#include <linux/platform_device.h>
+
+#include "eseries-gpio.h"
+
+#include <asm/irq.h>
+#include <asm/mach-types.h>
+
+#include <pcmcia/soc_common.h>
+
+static int e740_pcmcia_hw_init(struct soc_pcmcia_socket *skt)
+{
+	if (skt->nr == 0) {
+		skt->stat[SOC_STAT_CD].gpio = GPIO_E740_PCMCIA_CD0;
+		skt->stat[SOC_STAT_CD].name = "CF card detect";
+		skt->stat[SOC_STAT_RDY].gpio = GPIO_E740_PCMCIA_RDY0;
+		skt->stat[SOC_STAT_RDY].name = "CF ready";
+	} else {
+		skt->stat[SOC_STAT_CD].gpio = GPIO_E740_PCMCIA_CD1;
+		skt->stat[SOC_STAT_CD].name = "Wifi switch";
+		skt->stat[SOC_STAT_RDY].gpio = GPIO_E740_PCMCIA_RDY1;
+		skt->stat[SOC_STAT_RDY].name = "Wifi ready";
+	}
+
+	return 0;
+}
+
+static void e740_pcmcia_socket_state(struct soc_pcmcia_socket *skt,
+					struct pcmcia_state *state)
+{
+	state->vs_3v  = 1;
+	state->vs_Xv  = 0;
+}
+
+static int e740_pcmcia_configure_socket(struct soc_pcmcia_socket *skt,
+					const socket_state_t *state)
+{
+	if (state->flags & SS_RESET) {
+		if (skt->nr == 0)
+			gpio_set_value(GPIO_E740_PCMCIA_RST0, 1);
+		else
+			gpio_set_value(GPIO_E740_PCMCIA_RST1, 1);
+	} else {
+		if (skt->nr == 0)
+			gpio_set_value(GPIO_E740_PCMCIA_RST0, 0);
+		else
+			gpio_set_value(GPIO_E740_PCMCIA_RST1, 0);
+	}
+
+	switch (state->Vcc) {
+	case 0:	/* Socket off */
+		if (skt->nr == 0)
+			gpio_set_value(GPIO_E740_PCMCIA_PWR0, 0);
+		else
+			gpio_set_value(GPIO_E740_PCMCIA_PWR1, 1);
+		break;
+	case 50:
+	case 33: /* socket on */
+		if (skt->nr == 0)
+			gpio_set_value(GPIO_E740_PCMCIA_PWR0, 1);
+		else
+			gpio_set_value(GPIO_E740_PCMCIA_PWR1, 0);
+		break;
+	default:
+		printk(KERN_ERR "e740_cs: Unsupported Vcc: %d\n", state->Vcc);
+	}
+
+	return 0;
+}
+
+static struct pcmcia_low_level e740_pcmcia_ops = {
+	.owner            = THIS_MODULE,
+	.hw_init          = e740_pcmcia_hw_init,
+	.socket_state     = e740_pcmcia_socket_state,
+	.configure_socket = e740_pcmcia_configure_socket,
+	.nr               = 2,
+};
+
+static struct platform_device *e740_pcmcia_device;
+
+static int __init e740_pcmcia_init(void)
+{
+	int ret;
+
+	if (!machine_is_e740())
+		return -ENODEV;
+
+	e740_pcmcia_device = platform_device_alloc("pxa2xx-pcmcia", -1);
+	if (!e740_pcmcia_device)
+		return -ENOMEM;
+
+	ret = platform_device_add_data(e740_pcmcia_device, &e740_pcmcia_ops,
+					sizeof(e740_pcmcia_ops));
+
+	if (!ret)
+		ret = platform_device_add(e740_pcmcia_device);
+
+	if (ret)
+		platform_device_put(e740_pcmcia_device);
+
+	return ret;
+}
+
+static void __exit e740_pcmcia_exit(void)
+{
+	platform_device_unregister(e740_pcmcia_device);
+}
+
+module_init(e740_pcmcia_init);
+module_exit(e740_pcmcia_exit);
+
+MODULE_LICENSE("GPL v2");
+MODULE_AUTHOR("Ian Molton <spyro@f2s.com>");
+MODULE_ALIAS("platform:pxa2xx-pcmcia");
+MODULE_DESCRIPTION("e740 PCMCIA platform support");
diff --git a/arch/arm/mach-pxa/include/mach/eseries-gpio.h b/arch/arm/mach-pxa/eseries-gpio.h
index 5c645600d401..5c645600d401 100644
--- a/arch/arm/mach-pxa/include/mach/eseries-gpio.h
+++ b/arch/arm/mach-pxa/eseries-gpio.h
diff --git a/arch/arm/mach-pxa/eseries.c b/arch/arm/mach-pxa/eseries.c
index f37c44b6139d..2e4daeab6278 100644
--- a/arch/arm/mach-pxa/eseries.c
+++ b/arch/arm/mach-pxa/eseries.c
@@ -1,13 +1,8 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Hardware definitions for the Toshiba eseries PDAs
  *
  * Copyright (c) 2003 Ian Molton <spyro@f2s.com>
- *
- * This file is licensed under
- * the terms of the GNU General Public License version 2. This program
- * is licensed "as is" without any warranty of any kind, whether express
- * or implied.
- *
  */
 
 #include <linux/clkdev.h>
@@ -24,6 +19,7 @@
 #include <linux/mtd/rawnand.h>
 #include <linux/mtd/partitions.h>
 #include <linux/memblock.h>
+#include <linux/gpio/machine.h>
 
 #include <video/w100fb.h>
 
@@ -32,9 +28,9 @@
 #include <asm/mach-types.h>
 
 #include "pxa25x.h"
-#include <mach/eseries-gpio.h>
+#include "eseries-gpio.h"
 #include "eseries-irq.h"
-#include <mach/audio.h>
+#include <linux/platform_data/asoc-pxa.h>
 #include <linux/platform_data/video-pxafb.h>
 #include "udc.h"
 #include <linux/platform_data/irda-pxaficp.h>
@@ -85,11 +81,10 @@ int eseries_tmio_enable(struct platform_device *dev)
 	return 0;
 }
 
-int eseries_tmio_disable(struct platform_device *dev)
+void eseries_tmio_disable(struct platform_device *dev)
 {
 	gpio_set_value(GPIO_ESERIES_TMIO_SUSPEND, 0);
 	gpio_set_value(GPIO_ESERIES_TMIO_PCLR, 0);
-	return 0;
 }
 
 int eseries_tmio_suspend(struct platform_device *dev)
@@ -138,7 +133,6 @@ static void __init __maybe_unused eseries_register_clks(void)
 
 static struct tc6387xb_platform_data e330_tc6387xb_info = {
 	.enable   = &eseries_tmio_enable,
-	.disable  = &eseries_tmio_disable,
 	.suspend  = &eseries_tmio_suspend,
 	.resume   = &eseries_tmio_resume,
 };
@@ -520,6 +514,16 @@ static struct platform_device e740_audio_device = {
 	.id		= -1,
 };
 
+static struct gpiod_lookup_table e740_audio_gpio_table = {
+	.dev_id = "e740-audio",
+	.table = {
+		GPIO_LOOKUP("gpio-pxa",  GPIO_E740_WM9705_nAVDD2, "Audio power",  GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP("gpio-pxa",  GPIO_E740_AMP_ON, "Output amp",  GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP("gpio-pxa",  GPIO_E740_MIC_ON, "Mic amp", GPIO_ACTIVE_HIGH),
+		{ },
+	},
+};
+
 /* ----------------------------------------------------------------------- */
 
 static struct platform_device *e740_devices[] __initdata = {
@@ -540,6 +544,7 @@ static void __init e740_init(void)
 			"UDCCLK", &pxa25x_device_udc.dev),
 	eseries_get_tmio_gpios();
 	gpiod_add_lookup_table(&e7xx_gpio_vbus_gpiod_table);
+	gpiod_add_lookup_table(&e740_audio_gpio_table);
 	platform_add_devices(ARRAY_AND_SIZE(e740_devices));
 	pxa_set_ac97_info(NULL);
 	pxa_set_ficp_info(&e7xx_ficp_platform_data);
@@ -699,7 +704,6 @@ static struct tc6393xb_platform_data e750_tc6393xb_info = {
 	.irq_base       = IRQ_BOARD_START,
 	.scr_pll2cr     = 0x0cc1,
 	.scr_gper       = 0,
-	.gpio_base      = -1,
 	.suspend        = &eseries_tmio_suspend,
 	.resume         = &eseries_tmio_resume,
 	.enable         = &eseries_tmio_enable,
@@ -716,6 +720,15 @@ static struct platform_device e750_tc6393xb_device = {
 	.resource      = eseries_tmio_resources,
 };
 
+static struct gpiod_lookup_table e750_audio_gpio_table = {
+	.dev_id = "e750-audio",
+	.table = {
+		GPIO_LOOKUP("gpio-pxa",  GPIO_E750_HP_AMP_OFF, "Output amp",  GPIO_ACTIVE_LOW),
+		GPIO_LOOKUP("gpio-pxa",  GPIO_E750_SPK_AMP_OFF, "Mic amp", GPIO_ACTIVE_LOW),
+		{ },
+	},
+};
+
 static struct platform_device e750_audio_device = {
 	.name		= "e750-audio",
 	.id		= -1,
@@ -740,6 +753,7 @@ static void __init e750_init(void)
 			"GPIO11_CLK", NULL),
 	eseries_get_tmio_gpios();
 	gpiod_add_lookup_table(&e7xx_gpio_vbus_gpiod_table);
+	gpiod_add_lookup_table(&e750_audio_gpio_table);
 	platform_add_devices(ARRAY_AND_SIZE(e750_devices));
 	pxa_set_ac97_info(NULL);
 	pxa_set_ficp_info(&e7xx_ficp_platform_data);
@@ -918,7 +932,6 @@ static struct tc6393xb_platform_data e800_tc6393xb_info = {
 	.irq_base       = IRQ_BOARD_START,
 	.scr_pll2cr     = 0x0cc1,
 	.scr_gper       = 0,
-	.gpio_base      = -1,
 	.suspend        = &eseries_tmio_suspend,
 	.resume         = &eseries_tmio_resume,
 	.enable         = &eseries_tmio_enable,
@@ -935,6 +948,15 @@ static struct platform_device e800_tc6393xb_device = {
 	.resource      = eseries_tmio_resources,
 };
 
+static struct gpiod_lookup_table e800_audio_gpio_table = {
+	.dev_id = "e800-audio",
+	.table = {
+		GPIO_LOOKUP("gpio-pxa",  GPIO_E800_HP_AMP_OFF, "Output amp",  GPIO_ACTIVE_LOW),
+		GPIO_LOOKUP("gpio-pxa",  GPIO_E800_SPK_AMP_ON, "Mic amp", GPIO_ACTIVE_HIGH),
+		{ },
+	},
+};
+
 static struct platform_device e800_audio_device = {
 	.name		= "e800-audio",
 	.id		= -1,
@@ -959,6 +981,7 @@ static void __init e800_init(void)
 			"GPIO11_CLK", NULL),
 	eseries_get_tmio_gpios();
 	gpiod_add_lookup_table(&e800_gpio_vbus_gpiod_table);
+	gpiod_add_lookup_table(&e800_audio_gpio_table);
 	platform_add_devices(ARRAY_AND_SIZE(e800_devices));
 	pxa_set_ac97_info(NULL);
 }
diff --git a/arch/arm/mach-pxa/ezx.c b/arch/arm/mach-pxa/ezx.c
index eb85950e7c0e..69c2ec02a16c 100644
--- a/arch/arm/mach-pxa/ezx.c
+++ b/arch/arm/mach-pxa/ezx.c
@@ -29,7 +29,6 @@
 #include "pxa27x.h"
 #include <linux/platform_data/video-pxafb.h>
 #include <linux/platform_data/usb-ohci-pxa27x.h>
-#include <mach/hardware.h>
 #include <linux/platform_data/keypad-pxa27x.h>
 #include <linux/platform_data/media/camera-pxa.h>
 
diff --git a/arch/arm/mach-pxa/generic.c b/arch/arm/mach-pxa/generic.c
index ab7cdffd7ea8..02fdde7e3e34 100644
--- a/arch/arm/mach-pxa/generic.c
+++ b/arch/arm/mach-pxa/generic.c
@@ -17,15 +17,18 @@
 #include <linux/module.h>
 #include <linux/kernel.h>
 #include <linux/init.h>
+#include <linux/soc/pxa/cpu.h>
+#include <linux/soc/pxa/smemc.h>
+#include <linux/clk/pxa.h>
 
-#include <mach/hardware.h>
 #include <asm/mach/map.h>
 #include <asm/mach-types.h>
 
-#include <mach/irqs.h>
-#include <mach/reset.h>
-#include <mach/smemc.h>
-#include <mach/pxa3xx-regs.h>
+#include "addr-map.h"
+#include "irqs.h"
+#include "reset.h"
+#include "smemc.h"
+#include "pxa3xx-regs.h"
 
 #include "generic.h"
 #include <clocksource/pxa.h>
@@ -46,28 +49,47 @@ void clear_reset_status(unsigned int mask)
 void __init pxa_timer_init(void)
 {
 	if (cpu_is_pxa25x())
-		pxa25x_clocks_init();
+		pxa25x_clocks_init(io_p2v(0x41300000));
 	if (cpu_is_pxa27x())
-		pxa27x_clocks_init();
+		pxa27x_clocks_init(io_p2v(0x41300000));
 	if (cpu_is_pxa3xx())
-		pxa3xx_clocks_init();
+		pxa3xx_clocks_init(io_p2v(0x41340000), io_p2v(0x41350000));
 	pxa_timer_nodt_init(IRQ_OST0, io_p2v(0x40a00000));
 }
 
-/*
- * Get the clock frequency as reflected by CCCR and the turbo flag.
- * We assume these values have been applied via a fcs.
- * If info is not 0 we also display the current settings.
- */
-unsigned int get_clk_frequency_khz(int info)
+void pxa_smemc_set_pcmcia_timing(int sock, u32 mcmem, u32 mcatt, u32 mcio)
 {
-	if (cpu_is_pxa25x())
-		return pxa25x_get_clk_frequency_khz(info);
-	else if (cpu_is_pxa27x())
-		return pxa27x_get_clk_frequency_khz(info);
-	return 0;
+	__raw_writel(mcmem, MCMEM(sock));
+	__raw_writel(mcatt, MCATT(sock));
+	__raw_writel(mcio, MCIO(sock));
+}
+EXPORT_SYMBOL_GPL(pxa_smemc_set_pcmcia_timing);
+
+void pxa_smemc_set_pcmcia_socket(int nr)
+{
+	switch (nr) {
+	case 0:
+		__raw_writel(0, MECR);
+		break;
+	case 1:
+		/*
+		 * We have at least one socket, so set MECR:CIT
+		 * (Card Is There)
+		 */
+		__raw_writel(MECR_CIT, MECR);
+		break;
+	case 2:
+		/* Set CIT and MECR:NOS (Number Of Sockets) */
+		__raw_writel(MECR_CIT | MECR_NOS, MECR);
+		break;
+	}
+}
+EXPORT_SYMBOL_GPL(pxa_smemc_set_pcmcia_socket);
+
+void __iomem *pxa_smemc_get_mdrefr(void)
+{
+	return MDREFR;
 }
-EXPORT_SYMBOL(get_clk_frequency_khz);
 
 /*
  * Intel PXA2xx internal register mapping.
diff --git a/arch/arm/mach-pxa/generic.h b/arch/arm/mach-pxa/generic.h
index 3b7873f8e1f8..7bb1499de4c5 100644
--- a/arch/arm/mach-pxa/generic.h
+++ b/arch/arm/mach-pxa/generic.h
@@ -10,7 +10,6 @@
 
 struct irq_data;
 
-extern unsigned int get_clk_frequency_khz(int info);
 extern void __init pxa_dt_irq_init(int (*fn)(struct irq_data *,
 					     unsigned int));
 extern void __init pxa_map_io(void);
@@ -23,19 +22,16 @@ extern void pxa_timer_init(void);
 #define ARRAY_AND_SIZE(x)	(x), ARRAY_SIZE(x)
 
 #define pxa25x_handle_irq icip_handle_irq
-extern int __init pxa25x_clocks_init(void);
 extern void __init pxa25x_init_irq(void);
 extern void __init pxa25x_map_io(void);
 extern void __init pxa26x_init_irq(void);
 
 #define pxa27x_handle_irq ichp_handle_irq
-extern int __init pxa27x_clocks_init(void);
 extern unsigned	pxa27x_get_clk_frequency_khz(int);
 extern void __init pxa27x_init_irq(void);
 extern void __init pxa27x_map_io(void);
 
 #define pxa3xx_handle_irq ichp_handle_irq
-extern int __init pxa3xx_clocks_init(void);
 extern void __init pxa3xx_init_irq(void);
 extern void __init pxa3xx_map_io(void);
 
@@ -71,8 +67,3 @@ extern unsigned pxa25x_get_clk_frequency_khz(int);
 #define pxa27x_get_clk_frequency_khz(x)		(0)
 #endif
 
-#ifdef CONFIG_PXA3xx
-extern unsigned	pxa3xx_get_clk_frequency_khz(int);
-#else
-#define pxa3xx_get_clk_frequency_khz(x)		(0)
-#endif
diff --git a/arch/arm/mach-pxa/gumstix.c b/arch/arm/mach-pxa/gumstix.c
index 49dd618b10f7..72b08a9bf0fd 100644
--- a/arch/arm/mach-pxa/gumstix.c
+++ b/arch/arm/mach-pxa/gumstix.c
@@ -28,7 +28,6 @@
 #include <asm/setup.h>
 #include <asm/memory.h>
 #include <asm/mach-types.h>
-#include <mach/hardware.h>
 #include <asm/irq.h>
 #include <linux/sizes.h>
 
diff --git a/arch/arm/mach-pxa/gumstix.h b/arch/arm/mach-pxa/gumstix.h
index 470250cdee16..9005b3c0aabd 100644
--- a/arch/arm/mach-pxa/gumstix.h
+++ b/arch/arm/mach-pxa/gumstix.h
@@ -3,7 +3,7 @@
  *  arch/arm/mach-pxa/include/mach/gumstix.h
  */
 
-#include <mach/irqs.h> /* PXA_GPIO_TO_IRQ */
+#include "irqs.h" /* PXA_GPIO_TO_IRQ */
 
 /* BTRESET - Reset line to Bluetooth module, active low signal. */
 #define GPIO_GUMSTIX_BTRESET          7
diff --git a/arch/arm/mach-pxa/h5000.c b/arch/arm/mach-pxa/h5000.c
index ece1e71c90a9..212efe24aedb 100644
--- a/arch/arm/mach-pxa/h5000.c
+++ b/arch/arm/mach-pxa/h5000.c
@@ -29,7 +29,7 @@
 #include "pxa25x.h"
 #include "h5000.h"
 #include "udc.h"
-#include <mach/smemc.h>
+#include "smemc.h"
 
 #include "generic.h"
 
diff --git a/arch/arm/mach-pxa/hx4700-pcmcia.c b/arch/arm/mach-pxa/hx4700-pcmcia.c
new file mode 100644
index 000000000000..e2331dfe427d
--- /dev/null
+++ b/arch/arm/mach-pxa/hx4700-pcmcia.c
@@ -0,0 +1,118 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ *  Copyright (C) 2012 Paul Parsons <lost.distance@yahoo.com>
+ */
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/err.h>
+#include <linux/gpio.h>
+#include <linux/irq.h>
+
+#include <asm/mach-types.h>
+#include "hx4700.h"
+
+#include <pcmcia/soc_common.h>
+
+static struct gpio gpios[] = {
+	{ GPIO114_HX4700_CF_RESET,    GPIOF_OUT_INIT_LOW,   "CF reset"        },
+	{ EGPIO4_CF_3V3_ON,           GPIOF_OUT_INIT_LOW,   "CF 3.3V enable"  },
+};
+
+static int hx4700_pcmcia_hw_init(struct soc_pcmcia_socket *skt)
+{
+	int ret;
+
+	ret = gpio_request_array(gpios, ARRAY_SIZE(gpios));
+	if (ret)
+		goto out;
+
+	/*
+	 * IRQ type must be set before soc_pcmcia_hw_init() calls request_irq().
+	 * The asic3 default IRQ type is level trigger low level detect, exactly
+	 * the the signal present on GPIOD4_CF_nCD when a CF card is inserted.
+	 * If the IRQ type is not changed, the asic3 interrupt handler will loop
+	 * repeatedly because it is unable to clear the level trigger interrupt.
+	 */
+	irq_set_irq_type(gpio_to_irq(GPIOD4_CF_nCD), IRQ_TYPE_EDGE_BOTH);
+
+	skt->stat[SOC_STAT_CD].gpio = GPIOD4_CF_nCD;
+	skt->stat[SOC_STAT_CD].name = "PCMCIA CD";
+	skt->stat[SOC_STAT_RDY].gpio = GPIO60_HX4700_CF_RNB;
+	skt->stat[SOC_STAT_RDY].name = "PCMCIA Ready";
+
+out:
+	return ret;
+}
+
+static void hx4700_pcmcia_hw_shutdown(struct soc_pcmcia_socket *skt)
+{
+	gpio_free_array(gpios, ARRAY_SIZE(gpios));
+}
+
+static void hx4700_pcmcia_socket_state(struct soc_pcmcia_socket *skt,
+	struct pcmcia_state *state)
+{
+	state->vs_3v = 1;
+	state->vs_Xv = 0;
+}
+
+static int hx4700_pcmcia_configure_socket(struct soc_pcmcia_socket *skt,
+	const socket_state_t *state)
+{
+	switch (state->Vcc) {
+	case 0:
+		gpio_set_value(EGPIO4_CF_3V3_ON, 0);
+		break;
+	case 33:
+		gpio_set_value(EGPIO4_CF_3V3_ON, 1);
+		break;
+	default:
+		printk(KERN_ERR "pcmcia: Unsupported Vcc: %d\n", state->Vcc);
+		return -EINVAL;
+	}
+
+	gpio_set_value(GPIO114_HX4700_CF_RESET, (state->flags & SS_RESET) != 0);
+
+	return 0;
+}
+
+static struct pcmcia_low_level hx4700_pcmcia_ops = {
+	.owner          = THIS_MODULE,
+	.nr             = 1,
+	.hw_init        = hx4700_pcmcia_hw_init,
+	.hw_shutdown    = hx4700_pcmcia_hw_shutdown,
+	.socket_state   = hx4700_pcmcia_socket_state,
+	.configure_socket = hx4700_pcmcia_configure_socket,
+};
+
+static struct platform_device *hx4700_pcmcia_device;
+
+static int __init hx4700_pcmcia_init(void)
+{
+	struct platform_device *pdev;
+
+	if (!machine_is_h4700())
+		return -ENODEV;
+
+	pdev = platform_device_register_data(NULL, "pxa2xx-pcmcia", -1,
+		&hx4700_pcmcia_ops, sizeof(hx4700_pcmcia_ops));
+	if (IS_ERR(pdev))
+		return PTR_ERR(pdev);
+
+	hx4700_pcmcia_device = pdev;
+
+	return 0;
+}
+
+static void __exit hx4700_pcmcia_exit(void)
+{
+	platform_device_unregister(hx4700_pcmcia_device);
+}
+
+module_init(hx4700_pcmcia_init);
+module_exit(hx4700_pcmcia_exit);
+
+MODULE_AUTHOR("Paul Parsons <lost.distance@yahoo.com>");
+MODULE_DESCRIPTION("HP iPAQ hx4700 PCMCIA driver");
+MODULE_LICENSE("GPL");
diff --git a/arch/arm/mach-pxa/hx4700.c b/arch/arm/mach-pxa/hx4700.c
index 1d4c5db54be2..2fd665944103 100644
--- a/arch/arm/mach-pxa/hx4700.c
+++ b/arch/arm/mach-pxa/hx4700.c
@@ -36,12 +36,12 @@
 #include <linux/spi/pxa2xx_spi.h>
 #include <linux/platform_data/i2c-pxa.h>
 
-#include <mach/hardware.h>
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
 
 #include "pxa27x.h"
-#include <mach/hx4700.h>
+#include "addr-map.h"
+#include "hx4700.h"
 #include <linux/platform_data/irda-pxaficp.h>
 
 #include <sound/ak4641.h>
@@ -616,7 +616,6 @@ static struct pxa2xx_spi_chip tsc2046_chip = {
 	.tx_threshold = 1,
 	.rx_threshold = 2,
 	.timeout      = 64,
-	.gpio_cs      = GPIO88_HX4700_TSC2046_CS,
 };
 
 static struct spi_board_info tsc2046_board_info[] __initdata = {
@@ -635,6 +634,14 @@ static struct pxa2xx_spi_controller pxa_ssp2_master_info = {
 	.enable_dma     = 1,
 };
 
+static struct gpiod_lookup_table pxa_ssp2_gpio_table = {
+	.dev_id = "spi2",
+	.table = {
+		GPIO_LOOKUP_IDX("gpio-pxa", GPIO88_HX4700_TSC2046_CS, "cs", 0, GPIO_ACTIVE_LOW),
+		{ },
+	},
+};
+
 /*
  * External power
  */
@@ -827,6 +834,19 @@ static struct i2c_board_info i2c_board_info[] __initdata = {
 	},
 };
 
+static struct gpiod_lookup_table hx4700_audio_gpio_table = {
+	.dev_id = "hx4700-audio",
+	.table = {
+		GPIO_LOOKUP("gpio-pxa", GPIO75_HX4700_EARPHONE_nDET,
+			    "earphone-det", GPIO_ACTIVE_LOW),
+		GPIO_LOOKUP("gpio-pxa", GPIO92_HX4700_HP_DRIVER,
+			    "hp-driver", GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP("gpio-pxa", GPIO107_HX4700_SPK_nSD,
+			    "spk-sd", GPIO_ACTIVE_LOW),
+		{ },
+	},
+};
+
 static struct platform_device audio = {
 	.name	= "hx4700-audio",
 	.id	= -1,
@@ -888,6 +908,7 @@ static void __init hx4700_init(void)
 
 	gpiod_add_lookup_table(&bq24022_gpiod_table);
 	gpiod_add_lookup_table(&gpio_vbus_gpiod_table);
+	gpiod_add_lookup_table(&hx4700_audio_gpio_table);
 	platform_add_devices(devices, ARRAY_SIZE(devices));
 	pwm_add_table(hx4700_pwm_lookup, ARRAY_SIZE(hx4700_pwm_lookup));
 
@@ -896,6 +917,7 @@ static void __init hx4700_init(void)
 	pxa_set_i2c_info(NULL);
 	i2c_register_board_info(0, ARRAY_AND_SIZE(i2c_board_info));
 	i2c_register_board_info(1, ARRAY_AND_SIZE(pi2c_board_info));
+	gpiod_add_lookup_table(&pxa_ssp2_gpio_table);
 	pxa2xx_set_spi_info(2, &pxa_ssp2_master_info);
 	spi_register_board_info(ARRAY_AND_SIZE(tsc2046_board_info));
 
diff --git a/arch/arm/mach-pxa/include/mach/hx4700.h b/arch/arm/mach-pxa/hx4700.h
index 0c30e6d9c660..0c30e6d9c660 100644
--- a/arch/arm/mach-pxa/include/mach/hx4700.h
+++ b/arch/arm/mach-pxa/hx4700.h
diff --git a/arch/arm/mach-pxa/icontrol.c b/arch/arm/mach-pxa/icontrol.c
index 04a12523cdee..624088257cfc 100644
--- a/arch/arm/mach-pxa/icontrol.c
+++ b/arch/arm/mach-pxa/icontrol.c
@@ -13,7 +13,7 @@
 #include <linux/irq.h>
 #include <linux/platform_device.h>
 #include <linux/property.h>
-#include <linux/gpio.h>
+#include <linux/gpio/machine.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
@@ -42,7 +42,6 @@ static struct pxa2xx_spi_chip mcp251x_chip_info1 = {
 	.rx_threshold   = 128,
 	.dma_burst_size = 8,
 	.timeout        = 235,
-	.gpio_cs        = ICONTROL_MCP251x_nCS1
 };
 
 static struct pxa2xx_spi_chip mcp251x_chip_info2 = {
@@ -50,7 +49,6 @@ static struct pxa2xx_spi_chip mcp251x_chip_info2 = {
 	.rx_threshold   = 128,
 	.dma_burst_size = 8,
 	.timeout        = 235,
-	.gpio_cs        = ICONTROL_MCP251x_nCS2
 };
 
 static struct pxa2xx_spi_chip mcp251x_chip_info3 = {
@@ -58,7 +56,6 @@ static struct pxa2xx_spi_chip mcp251x_chip_info3 = {
 	.rx_threshold   = 128,
 	.dma_burst_size = 8,
 	.timeout        = 235,
-	.gpio_cs        = ICONTROL_MCP251x_nCS3
 };
 
 static struct pxa2xx_spi_chip mcp251x_chip_info4 = {
@@ -66,7 +63,6 @@ static struct pxa2xx_spi_chip mcp251x_chip_info4 = {
 	.rx_threshold   = 128,
 	.dma_burst_size = 8,
 	.timeout        = 235,
-	.gpio_cs        = ICONTROL_MCP251x_nCS4
 };
 
 static const struct property_entry mcp251x_properties[] = {
@@ -143,6 +139,24 @@ struct platform_device pxa_spi_ssp4 = {
 	}
 };
 
+static struct gpiod_lookup_table pxa_ssp3_gpio_table = {
+	.dev_id = "spi3",
+	.table = {
+		GPIO_LOOKUP_IDX("gpio-pxa", ICONTROL_MCP251x_nCS1, "cs", 0, GPIO_ACTIVE_LOW),
+		GPIO_LOOKUP_IDX("gpio-pxa", ICONTROL_MCP251x_nCS2, "cs", 1, GPIO_ACTIVE_LOW),
+		{ },
+	},
+};
+
+static struct gpiod_lookup_table pxa_ssp4_gpio_table = {
+	.dev_id = "spi4",
+	.table = {
+		GPIO_LOOKUP_IDX("gpio-pxa", ICONTROL_MCP251x_nCS3, "cs", 0, GPIO_ACTIVE_LOW),
+		GPIO_LOOKUP_IDX("gpio-pxa", ICONTROL_MCP251x_nCS4, "cs", 1, GPIO_ACTIVE_LOW),
+		{ },
+	},
+};
+
 static struct platform_device *icontrol_spi_devices[] __initdata = {
 	&pxa_spi_ssp3,
 	&pxa_spi_ssp4,
@@ -175,6 +189,8 @@ static mfp_cfg_t mfp_can_cfg[] __initdata = {
 static void __init icontrol_can_init(void)
 {
 	pxa3xx_mfp_config(ARRAY_AND_SIZE(mfp_can_cfg));
+	gpiod_add_lookup_table(&pxa_ssp3_gpio_table);
+	gpiod_add_lookup_table(&pxa_ssp4_gpio_table);
 	platform_add_devices(ARRAY_AND_SIZE(icontrol_spi_devices));
 	spi_register_board_info(ARRAY_AND_SIZE(mcp251x_board_info));
 }
diff --git a/arch/arm/mach-pxa/idp.c b/arch/arm/mach-pxa/idp.c
index fb0850af8496..525d01ddfbbb 100644
--- a/arch/arm/mach-pxa/idp.c
+++ b/arch/arm/mach-pxa/idp.c
@@ -22,7 +22,6 @@
 #include <asm/setup.h>
 #include <asm/memory.h>
 #include <asm/mach-types.h>
-#include <mach/hardware.h>
 #include <asm/irq.h>
 
 #include <asm/mach/arch.h>
@@ -31,7 +30,6 @@
 #include "pxa25x.h"
 #include "idp.h"
 #include <linux/platform_data/video-pxafb.h>
-#include <mach/bitfield.h>
 #include <linux/platform_data/mmc-pxamci.h>
 #include <linux/smc91x.h>
 
diff --git a/arch/arm/mach-pxa/idp.h b/arch/arm/mach-pxa/idp.h
index a89e6723b1a1..81b9bd9ba754 100644
--- a/arch/arm/mach-pxa/idp.h
+++ b/arch/arm/mach-pxa/idp.h
@@ -20,7 +20,7 @@
  * IDP hardware.
  */
 
-#include <mach/irqs.h> /* PXA_GPIO_TO_IRQ */
+#include "irqs.h" /* PXA_GPIO_TO_IRQ */
 
 #define IDP_FLASH_PHYS		(PXA_CS0_PHYS)
 #define IDP_ALT_FLASH_PHYS	(PXA_CS1_PHYS)
diff --git a/arch/arm/mach-pxa/include/mach/audio.h b/arch/arm/mach-pxa/include/mach/audio.h
deleted file mode 100644
index 7beebf7297b5..000000000000
--- a/arch/arm/mach-pxa/include/mach/audio.h
+++ /dev/null
@@ -1,31 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-#ifndef __ASM_ARCH_AUDIO_H__
-#define __ASM_ARCH_AUDIO_H__
-
-#include <sound/core.h>
-#include <sound/pcm.h>
-#include <sound/ac97_codec.h>
-
-/*
- * @reset_gpio: AC97 reset gpio (normally gpio113 or gpio95)
- *              a -1 value means no gpio will be used for reset
- * @codec_pdata: AC97 codec platform_data
-
- * reset_gpio should only be specified for pxa27x CPUs where a silicon
- * bug prevents correct operation of the reset line. If not specified,
- * the default behaviour on these CPUs is to consider gpio 113 as the
- * AC97 reset line, which is the default on most boards.
- */
-typedef struct {
-	int (*startup)(struct snd_pcm_substream *, void *);
-	void (*shutdown)(struct snd_pcm_substream *, void *);
-	void (*suspend)(void *);
-	void (*resume)(void *);
-	void *priv;
-	int reset_gpio;
-	void *codec_pdata[AC97_BUS_MAX_DEVICES];
-} pxa2xx_audio_ops_t;
-
-extern void pxa_set_ac97_info(pxa2xx_audio_ops_t *ops);
-
-#endif
diff --git a/arch/arm/mach-pxa/include/mach/bitfield.h b/arch/arm/mach-pxa/include/mach/bitfield.h
deleted file mode 100644
index fe2ca441bc0a..000000000000
--- a/arch/arm/mach-pxa/include/mach/bitfield.h
+++ /dev/null
@@ -1,114 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-/*
- *	FILE    	bitfield.h
- *
- *	Version 	1.1
- *	Author  	Copyright (c) Marc A. Viredaz, 1998
- *	        	DEC Western Research Laboratory, Palo Alto, CA
- *	Date    	April 1998 (April 1997)
- *	System  	Advanced RISC Machine (ARM)
- *	Language	C or ARM Assembly
- *	Purpose 	Definition of macros to operate on bit fields.
- */
-
-
-
-#ifndef __BITFIELD_H
-#define __BITFIELD_H
-
-#ifndef __ASSEMBLY__
-#define UData(Data)	((unsigned long) (Data))
-#else
-#define UData(Data)	(Data)
-#endif
-
-
-/*
- * MACRO: Fld
- *
- * Purpose
- *    The macro "Fld" encodes a bit field, given its size and its shift value
- *    with respect to bit 0.
- *
- * Note
- *    A more intuitive way to encode bit fields would have been to use their
- *    mask. However, extracting size and shift value information from a bit
- *    field's mask is cumbersome and might break the assembler (255-character
- *    line-size limit).
- *
- * Input
- *    Size      	Size of the bit field, in number of bits.
- *    Shft      	Shift value of the bit field with respect to bit 0.
- *
- * Output
- *    Fld       	Encoded bit field.
- */
-
-#define Fld(Size, Shft)	(((Size) << 16) + (Shft))
-
-
-/*
- * MACROS: FSize, FShft, FMsk, FAlnMsk, F1stBit
- *
- * Purpose
- *    The macros "FSize", "FShft", "FMsk", "FAlnMsk", and "F1stBit" return
- *    the size, shift value, mask, aligned mask, and first bit of a
- *    bit field.
- *
- * Input
- *    Field     	Encoded bit field (using the macro "Fld").
- *
- * Output
- *    FSize     	Size of the bit field, in number of bits.
- *    FShft     	Shift value of the bit field with respect to bit 0.
- *    FMsk      	Mask for the bit field.
- *    FAlnMsk   	Mask for the bit field, aligned on bit 0.
- *    F1stBit   	First bit of the bit field.
- */
-
-#define FSize(Field)	((Field) >> 16)
-#define FShft(Field)	((Field) & 0x0000FFFF)
-#define FMsk(Field)	(((UData (1) << FSize (Field)) - 1) << FShft (Field))
-#define FAlnMsk(Field)	((UData (1) << FSize (Field)) - 1)
-#define F1stBit(Field)	(UData (1) << FShft (Field))
-
-
-/*
- * MACRO: FInsrt
- *
- * Purpose
- *    The macro "FInsrt" inserts a value into a bit field by shifting the
- *    former appropriately.
- *
- * Input
- *    Value     	Bit-field value.
- *    Field     	Encoded bit field (using the macro "Fld").
- *
- * Output
- *    FInsrt    	Bit-field value positioned appropriately.
- */
-
-#define FInsrt(Value, Field) \
-                	(UData (Value) << FShft (Field))
-
-
-/*
- * MACRO: FExtr
- *
- * Purpose
- *    The macro "FExtr" extracts the value of a bit field by masking and
- *    shifting it appropriately.
- *
- * Input
- *    Data      	Data containing the bit-field to be extracted.
- *    Field     	Encoded bit field (using the macro "Fld").
- *
- * Output
- *    FExtr     	Bit-field value.
- */
-
-#define FExtr(Data, Field) \
-                	((UData (Data) >> FShft (Field)) & FAlnMsk (Field))
-
-
-#endif /* __BITFIELD_H */
diff --git a/arch/arm/mach-pxa/include/mach/dma.h b/arch/arm/mach-pxa/include/mach/dma.h
deleted file mode 100644
index 79f9842a7e1c..000000000000
--- a/arch/arm/mach-pxa/include/mach/dma.h
+++ /dev/null
@@ -1,17 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-only */
-/*
- *  arch/arm/mach-pxa/include/mach/dma.h
- *
- *  Author:	Nicolas Pitre
- *  Created:	Jun 15, 2001
- *  Copyright:	MontaVista Software, Inc.
- */
-#ifndef __ASM_ARCH_DMA_H
-#define __ASM_ARCH_DMA_H
-
-#include <mach/hardware.h>
-
-/* DMA Controller Registers Definitions */
-#define DMAC_REGS_VIRT	io_p2v(0x40000000)
-
-#endif /* _ASM_ARCH_DMA_H */
diff --git a/arch/arm/mach-pxa/include/mach/generic.h b/arch/arm/mach-pxa/include/mach/generic.h
deleted file mode 100644
index 665542e0c9e2..000000000000
--- a/arch/arm/mach-pxa/include/mach/generic.h
+++ /dev/null
@@ -1 +0,0 @@
-#include "../../generic.h"
diff --git a/arch/arm/mach-pxa/include/mach/hardware.h b/arch/arm/mach-pxa/include/mach/hardware.h
deleted file mode 100644
index ee7eab16135f..000000000000
--- a/arch/arm/mach-pxa/include/mach/hardware.h
+++ /dev/null
@@ -1,305 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-only */
-/*
- *  arch/arm/mach-pxa/include/mach/hardware.h
- *
- *  Author:	Nicolas Pitre
- *  Created:	Jun 15, 2001
- *  Copyright:	MontaVista Software Inc.
- */
-
-#ifndef __ASM_ARCH_HARDWARE_H
-#define __ASM_ARCH_HARDWARE_H
-
-#include <mach/addr-map.h>
-
-/*
- * Workarounds for at least 2 errata so far require this.
- * The mapping is set in mach-pxa/generic.c.
- */
-#define UNCACHED_PHYS_0		0xfe000000
-#define UNCACHED_PHYS_0_SIZE	0x00100000
-
-/*
- * Intel PXA2xx internal register mapping:
- *
- * 0x40000000 - 0x41ffffff <--> 0xf2000000 - 0xf3ffffff
- * 0x44000000 - 0x45ffffff <--> 0xf4000000 - 0xf5ffffff
- * 0x48000000 - 0x49ffffff <--> 0xf6000000 - 0xf7ffffff
- * 0x4c000000 - 0x4dffffff <--> 0xf8000000 - 0xf9ffffff
- * 0x50000000 - 0x51ffffff <--> 0xfa000000 - 0xfbffffff
- * 0x54000000 - 0x55ffffff <--> 0xfc000000 - 0xfdffffff
- * 0x58000000 - 0x59ffffff <--> 0xfe000000 - 0xffffffff
- *
- * Note that not all PXA2xx chips implement all those addresses, and the
- * kernel only maps the minimum needed range of this mapping.
- */
-#define io_v2p(x) (0x3c000000 + ((x) & 0x01ffffff) + (((x) & 0x0e000000) << 1))
-#define io_p2v(x) IOMEM(0xf2000000 + ((x) & 0x01ffffff) + (((x) & 0x1c000000) >> 1))
-
-#ifndef __ASSEMBLY__
-# define __REG(x)	(*((volatile u32 __iomem *)io_p2v(x)))
-
-/* With indexed regs we don't want to feed the index through io_p2v()
-   especially if it is a variable, otherwise horrible code will result. */
-# define __REG2(x,y)	\
-	(*(volatile u32 __iomem*)((u32)&__REG(x) + (y)))
-
-# define __PREG(x)	(io_v2p((u32)&(x)))
-
-#else
-
-# define __REG(x)	io_p2v(x)
-# define __PREG(x)	io_v2p(x)
-
-#endif
-
-#ifndef __ASSEMBLY__
-
-#include <asm/cputype.h>
-
-/*
- *   CPU     Stepping     CPU_ID         JTAG_ID
- *
- *  PXA210	B0	0x69052922	0x2926C013
- *  PXA210	B1	0x69052923	0x3926C013
- *  PXA210	B2	0x69052924	0x4926C013
- *  PXA210	C0	0x69052D25	0x5926C013
- *
- *  PXA250	A0	0x69052100	0x09264013
- *  PXA250	A1	0x69052101	0x19264013
- *  PXA250	B0	0x69052902	0x29264013
- *  PXA250	B1	0x69052903	0x39264013
- *  PXA250	B2	0x69052904	0x49264013
- *  PXA250	C0	0x69052D05	0x59264013
- *
- *  PXA255	A0	0x69052D06	0x69264013
- *
- *  PXA26x	A0	0x69052903	0x39264013
- *  PXA26x	B0	0x69052D05	0x59264013
- *
- *  PXA27x	A0	0x69054110	0x09265013
- *  PXA27x	A1	0x69054111	0x19265013
- *  PXA27x	B0	0x69054112	0x29265013
- *  PXA27x	B1	0x69054113	0x39265013
- *  PXA27x	C0	0x69054114	0x49265013
- *  PXA27x	C5	0x69054117	0x79265013
- *
- *  PXA30x	A0	0x69056880	0x0E648013
- *  PXA30x	A1	0x69056881	0x1E648013
- *  PXA31x	A0	0x69056890	0x0E649013
- *  PXA31x	A1	0x69056891	0x1E649013
- *  PXA31x	A2	0x69056892	0x2E649013
- *  PXA32x	B1	0x69056825	0x5E642013
- *  PXA32x	B2	0x69056826	0x6E642013
- *
- *  PXA930	B0	0x69056835	0x5E643013
- *  PXA930	B1	0x69056837	0x7E643013
- *  PXA930	B2	0x69056838	0x8E643013
- *
- *  PXA935	A0	0x56056931	0x1E653013
- *  PXA935	B0	0x56056936	0x6E653013
- *  PXA935	B1	0x56056938	0x8E653013
- */
-#ifdef CONFIG_PXA25x
-#define __cpu_is_pxa210(id)				\
-	({						\
-		unsigned int _id = (id) & 0xf3f0;	\
-		_id == 0x2120;				\
-	})
-
-#define __cpu_is_pxa250(id)				\
-	({						\
-		unsigned int _id = (id) & 0xf3ff;	\
-		_id <= 0x2105;				\
-	})
-
-#define __cpu_is_pxa255(id)				\
-	({						\
-		unsigned int _id = (id) & 0xffff;	\
-		_id == 0x2d06;				\
-	})
-
-#define __cpu_is_pxa25x(id)				\
-	({						\
-		unsigned int _id = (id) & 0xf300;	\
-		_id == 0x2100;				\
-	})
-#else
-#define __cpu_is_pxa210(id)	(0)
-#define __cpu_is_pxa250(id)	(0)
-#define __cpu_is_pxa255(id)	(0)
-#define __cpu_is_pxa25x(id)	(0)
-#endif
-
-#ifdef CONFIG_PXA27x
-#define __cpu_is_pxa27x(id)				\
-	({						\
-		unsigned int _id = (id) >> 4 & 0xfff;	\
-		_id == 0x411;				\
-	})
-#else
-#define __cpu_is_pxa27x(id)	(0)
-#endif
-
-#ifdef CONFIG_CPU_PXA300
-#define __cpu_is_pxa300(id)				\
-	({						\
-		unsigned int _id = (id) >> 4 & 0xfff;	\
-		_id == 0x688;				\
-	 })
-#else
-#define __cpu_is_pxa300(id)	(0)
-#endif
-
-#ifdef CONFIG_CPU_PXA310
-#define __cpu_is_pxa310(id)				\
-	({						\
-		unsigned int _id = (id) >> 4 & 0xfff;	\
-		_id == 0x689;				\
-	 })
-#else
-#define __cpu_is_pxa310(id)	(0)
-#endif
-
-#ifdef CONFIG_CPU_PXA320
-#define __cpu_is_pxa320(id)				\
-	({						\
-		unsigned int _id = (id) >> 4 & 0xfff;	\
-		_id == 0x603 || _id == 0x682;		\
-	 })
-#else
-#define __cpu_is_pxa320(id)	(0)
-#endif
-
-#ifdef CONFIG_CPU_PXA930
-#define __cpu_is_pxa930(id)				\
-	({						\
-		unsigned int _id = (id) >> 4 & 0xfff;	\
-		_id == 0x683;				\
-	 })
-#else
-#define __cpu_is_pxa930(id)	(0)
-#endif
-
-#ifdef CONFIG_CPU_PXA935
-#define __cpu_is_pxa935(id)				\
-	({						\
-		unsigned int _id = (id) >> 4 & 0xfff;	\
-		_id == 0x693;				\
-	 })
-#else
-#define __cpu_is_pxa935(id)	(0)
-#endif
-
-#define cpu_is_pxa210()					\
-	({						\
-		__cpu_is_pxa210(read_cpuid_id());	\
-	})
-
-#define cpu_is_pxa250()					\
-	({						\
-		__cpu_is_pxa250(read_cpuid_id());	\
-	})
-
-#define cpu_is_pxa255()                                 \
-	({                                              \
-		__cpu_is_pxa255(read_cpuid_id());       \
-	})
-
-#define cpu_is_pxa25x()					\
-	({						\
-		__cpu_is_pxa25x(read_cpuid_id());	\
-	})
-
-#define cpu_is_pxa27x()					\
-	({						\
-		__cpu_is_pxa27x(read_cpuid_id());	\
-	})
-
-#define cpu_is_pxa300()					\
-	({						\
-		__cpu_is_pxa300(read_cpuid_id());	\
-	 })
-
-#define cpu_is_pxa310()					\
-	({						\
-		__cpu_is_pxa310(read_cpuid_id());	\
-	 })
-
-#define cpu_is_pxa320()					\
-	({						\
-		__cpu_is_pxa320(read_cpuid_id());	\
-	 })
-
-#define cpu_is_pxa930()					\
-	({						\
-		__cpu_is_pxa930(read_cpuid_id());	\
-	 })
-
-#define cpu_is_pxa935()					\
-	({						\
-		__cpu_is_pxa935(read_cpuid_id());	\
-	 })
-
-
-
-/*
- * CPUID Core Generation Bit
- * <= 0x2 for pxa21x/pxa25x/pxa26x/pxa27x
- */
-#if defined(CONFIG_PXA25x) || defined(CONFIG_PXA27x)
-#define __cpu_is_pxa2xx(id)				\
-	({						\
-		unsigned int _id = (id) >> 13 & 0x7;	\
-		_id <= 0x2;				\
-	 })
-#else
-#define __cpu_is_pxa2xx(id)	(0)
-#endif
-
-#ifdef CONFIG_PXA3xx
-#define __cpu_is_pxa3xx(id)				\
-	({						\
-		__cpu_is_pxa300(id)			\
-			|| __cpu_is_pxa310(id)		\
-			|| __cpu_is_pxa320(id)		\
-			|| __cpu_is_pxa93x(id);		\
-	 })
-#else
-#define __cpu_is_pxa3xx(id)	(0)
-#endif
-
-#if defined(CONFIG_CPU_PXA930) || defined(CONFIG_CPU_PXA935)
-#define __cpu_is_pxa93x(id)				\
-	({						\
-		__cpu_is_pxa930(id)			\
-			|| __cpu_is_pxa935(id);		\
-	 })
-#else
-#define __cpu_is_pxa93x(id)	(0)
-#endif
-
-#define cpu_is_pxa2xx()					\
-	({						\
-		__cpu_is_pxa2xx(read_cpuid_id());	\
-	 })
-
-#define cpu_is_pxa3xx()					\
-	({						\
-		__cpu_is_pxa3xx(read_cpuid_id());	\
-	 })
-
-#define cpu_is_pxa93x()					\
-	({						\
-		__cpu_is_pxa93x(read_cpuid_id());	\
-	 })
-
-
-/*
- * return current memory and LCD clock frequency in units of 10kHz
- */
-extern unsigned int get_memclk_frequency_10khz(void);
-
-#endif
-
-#endif  /* _ASM_ARCH_HARDWARE_H */
diff --git a/arch/arm/mach-pxa/include/mach/mfp.h b/arch/arm/mach-pxa/include/mach/mfp.h
deleted file mode 100644
index dbb961fb570e..000000000000
--- a/arch/arm/mach-pxa/include/mach/mfp.h
+++ /dev/null
@@ -1,18 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-only */
-/*
- * arch/arm/mach-pxa/include/mach/mfp.h
- *
- * Multi-Function Pin Definitions
- *
- * Copyright (C) 2007 Marvell International Ltd.
- *
- * 2007-8-21: eric miao <eric.miao@marvell.com>
- *            initial version
- */
-
-#ifndef __ASM_ARCH_MFP_H
-#define __ASM_ARCH_MFP_H
-
-#include <plat/mfp.h>
-
-#endif /* __ASM_ARCH_MFP_H */
diff --git a/arch/arm/mach-pxa/include/mach/mtd-xip.h b/arch/arm/mach-pxa/include/mach/mtd-xip.h
deleted file mode 100644
index 4b31bef9e50a..000000000000
--- a/arch/arm/mach-pxa/include/mach/mtd-xip.h
+++ /dev/null
@@ -1,36 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-only */
-/*
- * MTD primitives for XIP support. Architecture specific functions
- *
- * Do not include this file directly. It's included from linux/mtd/xip.h
- * 
- * Author:	Nicolas Pitre
- * Created:	Nov 2, 2004
- * Copyright:	(C) 2004 MontaVista Software, Inc.
- */
-
-#ifndef __ARCH_PXA_MTD_XIP_H__
-#define __ARCH_PXA_MTD_XIP_H__
-
-#include <mach/regs-ost.h>
-
-/* restored July 2017, this did not build since 2011! */
-
-#define ICIP			io_p2v(0x40d00000)
-#define ICMR			io_p2v(0x40d00004)
-#define xip_irqpending()	(readl(ICIP) & readl(ICMR))
-
-/* we sample OSCR and convert desired delta to usec (1/4 ~= 1000000/3686400) */
-#define xip_currtime()		readl(OSCR)
-#define xip_elapsed_since(x)	(signed)((readl(OSCR) - (x)) / 4)
-
-/*
- * xip_cpu_idle() is used when waiting for a delay equal or larger than
- * the system timer tick period.  This should put the CPU into idle mode
- * to save power and to be woken up only when some interrupts are pending.
- * As above, this should not rely upon standard kernel code.
- */
-
-#define xip_cpu_idle()  asm volatile ("mcr p14, 0, %0, c7, c0, 0" :: "r" (1))
-
-#endif /* __ARCH_PXA_MTD_XIP_H__ */
diff --git a/arch/arm/mach-pxa/include/mach/pxa3xx-regs.h b/arch/arm/mach-pxa/include/mach/pxa3xx-regs.h
deleted file mode 100644
index 070f6c74196e..000000000000
--- a/arch/arm/mach-pxa/include/mach/pxa3xx-regs.h
+++ /dev/null
@@ -1,203 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-only */
-/*
- * arch/arm/mach-pxa/include/mach/pxa3xx-regs.h
- *
- * PXA3xx specific register definitions
- *
- * Copyright (C) 2007 Marvell International Ltd.
- */
-
-#ifndef __ASM_ARCH_PXA3XX_REGS_H
-#define __ASM_ARCH_PXA3XX_REGS_H
-
-#include <mach/hardware.h>
-
-/*
- * Oscillator Configuration Register (OSCC)
- */
-#define OSCC           io_p2v(0x41350000)  /* Oscillator Configuration Register */
-
-#define OSCC_PEN       (1 << 11)       /* 13MHz POUT */
-
-
-/*
- * Service Power Management Unit (MPMU)
- */
-#define PMCR		__REG(0x40F50000)	/* Power Manager Control Register */
-#define PSR		__REG(0x40F50004)	/* Power Manager S2 Status Register */
-#define PSPR		__REG(0x40F50008)	/* Power Manager Scratch Pad Register */
-#define PCFR		__REG(0x40F5000C)	/* Power Manager General Configuration Register */
-#define PWER		__REG(0x40F50010)	/* Power Manager Wake-up Enable Register */
-#define PWSR		__REG(0x40F50014)	/* Power Manager Wake-up Status Register */
-#define PECR		__REG(0x40F50018)	/* Power Manager EXT_WAKEUP[1:0] Control Register */
-#define DCDCSR		__REG(0x40F50080)	/* DC-DC Controller Status Register */
-#define PVCR		__REG(0x40F50100)	/* Power Manager Voltage Change Control Register */
-#define PCMD(x)		__REG(0x40F50110 + ((x) << 2))
-
-/*
- * Slave Power Management Unit
- */
-#define ASCR		__REG(0x40f40000)	/* Application Subsystem Power Status/Configuration */
-#define ARSR		__REG(0x40f40004)	/* Application Subsystem Reset Status */
-#define AD3ER		__REG(0x40f40008)	/* Application Subsystem Wake-Up from D3 Enable */
-#define AD3SR		__REG(0x40f4000c)	/* Application Subsystem Wake-Up from D3 Status */
-#define AD2D0ER		__REG(0x40f40010)	/* Application Subsystem Wake-Up from D2 to D0 Enable */
-#define AD2D0SR		__REG(0x40f40014)	/* Application Subsystem Wake-Up from D2 to D0 Status */
-#define AD2D1ER		__REG(0x40f40018)	/* Application Subsystem Wake-Up from D2 to D1 Enable */
-#define AD2D1SR		__REG(0x40f4001c)	/* Application Subsystem Wake-Up from D2 to D1 Status */
-#define AD1D0ER		__REG(0x40f40020)	/* Application Subsystem Wake-Up from D1 to D0 Enable */
-#define AD1D0SR		__REG(0x40f40024)	/* Application Subsystem Wake-Up from D1 to D0 Status */
-#define AGENP		__REG(0x40f4002c)	/* Application Subsystem General Purpose */
-#define AD3R		__REG(0x40f40030)	/* Application Subsystem D3 Configuration */
-#define AD2R		__REG(0x40f40034)	/* Application Subsystem D2 Configuration */
-#define AD1R		__REG(0x40f40038)	/* Application Subsystem D1 Configuration */
-
-/*
- * Application Subsystem Configuration bits.
- */
-#define ASCR_RDH		(1 << 31)
-#define ASCR_D1S		(1 << 2)
-#define ASCR_D2S		(1 << 1)
-#define ASCR_D3S		(1 << 0)
-
-/*
- * Application Reset Status bits.
- */
-#define ARSR_GPR		(1 << 3)
-#define ARSR_LPMR		(1 << 2)
-#define ARSR_WDT		(1 << 1)
-#define ARSR_HWR		(1 << 0)
-
-/*
- * Application Subsystem Wake-Up bits.
- */
-#define ADXER_WRTC		(1 << 31)	/* RTC */
-#define ADXER_WOST		(1 << 30)	/* OS Timer */
-#define ADXER_WTSI		(1 << 29)	/* Touchscreen */
-#define ADXER_WUSBH		(1 << 28)	/* USB host */
-#define ADXER_WUSB2		(1 << 26)	/* USB client 2.0 */
-#define ADXER_WMSL0		(1 << 24)	/* MSL port 0*/
-#define ADXER_WDMUX3		(1 << 23)	/* USB EDMUX3 */
-#define ADXER_WDMUX2		(1 << 22)	/* USB EDMUX2 */
-#define ADXER_WKP		(1 << 21)	/* Keypad */
-#define ADXER_WUSIM1		(1 << 20)	/* USIM Port 1 */
-#define ADXER_WUSIM0		(1 << 19)	/* USIM Port 0 */
-#define ADXER_WOTG		(1 << 16)	/* USBOTG input */
-#define ADXER_MFP_WFLASH	(1 << 15)	/* MFP: Data flash busy */
-#define ADXER_MFP_GEN12		(1 << 14)	/* MFP: MMC3/GPIO/OST inputs */
-#define ADXER_MFP_WMMC2		(1 << 13)	/* MFP: MMC2 */
-#define ADXER_MFP_WMMC1		(1 << 12)	/* MFP: MMC1 */
-#define ADXER_MFP_WI2C		(1 << 11)	/* MFP: I2C */
-#define ADXER_MFP_WSSP4		(1 << 10)	/* MFP: SSP4 */
-#define ADXER_MFP_WSSP3		(1 << 9)	/* MFP: SSP3 */
-#define ADXER_MFP_WMAXTRIX	(1 << 8)	/* MFP: matrix keypad */
-#define ADXER_MFP_WUART3	(1 << 7)	/* MFP: UART3 */
-#define ADXER_MFP_WUART2	(1 << 6)	/* MFP: UART2 */
-#define ADXER_MFP_WUART1	(1 << 5)	/* MFP: UART1 */
-#define ADXER_MFP_WSSP2		(1 << 4)	/* MFP: SSP2 */
-#define ADXER_MFP_WSSP1		(1 << 3)	/* MFP: SSP1 */
-#define ADXER_MFP_WAC97		(1 << 2)	/* MFP: AC97 */
-#define ADXER_WEXTWAKE1		(1 << 1)	/* External Wake 1 */
-#define ADXER_WEXTWAKE0		(1 << 0)	/* External Wake 0 */
-
-/*
- * AD3R/AD2R/AD1R bits.  R2-R5 are only defined for PXA320.
- */
-#define ADXR_L2			(1 << 8)
-#define ADXR_R5			(1 << 5)
-#define ADXR_R4			(1 << 4)
-#define ADXR_R3			(1 << 3)
-#define ADXR_R2			(1 << 2)
-#define ADXR_R1			(1 << 1)
-#define ADXR_R0			(1 << 0)
-
-/*
- * Values for PWRMODE CP15 register
- */
-#define PXA3xx_PM_S3D4C4	0x07	/* aka deep sleep */
-#define PXA3xx_PM_S2D3C4	0x06	/* aka sleep */
-#define PXA3xx_PM_S0D2C2	0x03	/* aka standby */
-#define PXA3xx_PM_S0D1C2	0x02	/* aka LCD refresh */
-#define PXA3xx_PM_S0D0C1	0x01
-
-/*
- * Application Subsystem Clock
- */
-#define ACCR		__REG(0x41340000)	/* Application Subsystem Clock Configuration Register */
-#define ACSR		__REG(0x41340004)	/* Application Subsystem Clock Status Register */
-#define AICSR		__REG(0x41340008)	/* Application Subsystem Interrupt Control/Status Register */
-#define CKENA		__REG(0x4134000C)	/* A Clock Enable Register */
-#define CKENB		__REG(0x41340010)	/* B Clock Enable Register */
-#define CKENC		__REG(0x41340024)	/* C Clock Enable Register */
-#define AC97_DIV	__REG(0x41340014)	/* AC97 clock divisor value register */
-
-#define ACCR_XPDIS		(1 << 31)	/* Core PLL Output Disable */
-#define ACCR_SPDIS		(1 << 30)	/* System PLL Output Disable */
-#define ACCR_D0CS		(1 << 26)	/* D0 Mode Clock Select */
-#define ACCR_PCCE		(1 << 11)	/* Power Mode Change Clock Enable */
-#define ACCR_DDR_D0CS		(1 << 7)	/* DDR SDRAM clock frequency in D0CS (PXA31x only) */
-
-#define ACCR_SMCFS_MASK		(0x7 << 23)	/* Static Memory Controller Frequency Select */
-#define ACCR_SFLFS_MASK		(0x3 << 18)	/* Frequency Select for Internal Memory Controller */
-#define ACCR_XSPCLK_MASK	(0x3 << 16)	/* Core Frequency during Frequency Change */
-#define ACCR_HSS_MASK		(0x3 << 14)	/* System Bus-Clock Frequency Select */
-#define ACCR_DMCFS_MASK		(0x3 << 12)	/* Dynamic Memory Controller Clock Frequency Select */
-#define ACCR_XN_MASK		(0x7 << 8)	/* Core PLL Turbo-Mode-to-Run-Mode Ratio */
-#define ACCR_XL_MASK		(0x1f)		/* Core PLL Run-Mode-to-Oscillator Ratio */
-
-#define ACCR_SMCFS(x)		(((x) & 0x7) << 23)
-#define ACCR_SFLFS(x)		(((x) & 0x3) << 18)
-#define ACCR_XSPCLK(x)		(((x) & 0x3) << 16)
-#define ACCR_HSS(x)		(((x) & 0x3) << 14)
-#define ACCR_DMCFS(x)		(((x) & 0x3) << 12)
-#define ACCR_XN(x)		(((x) & 0x7) << 8)
-#define ACCR_XL(x)		((x) & 0x1f)
-
-/*
- * Clock Enable Bit
- */
-#define CKEN_LCD	1	/* < LCD Clock Enable */
-#define CKEN_USBH	2	/* < USB host clock enable */
-#define CKEN_CAMERA	3	/* < Camera interface clock enable */
-#define CKEN_NAND	4	/* < NAND Flash Controller Clock Enable */
-#define CKEN_USB2	6	/* < USB 2.0 client clock enable. */
-#define CKEN_DMC	8	/* < Dynamic Memory Controller clock enable */
-#define CKEN_SMC	9	/* < Static Memory Controller clock enable */
-#define CKEN_ISC	10	/* < Internal SRAM Controller clock enable */
-#define CKEN_BOOT	11	/* < Boot rom clock enable */
-#define CKEN_MMC1	12	/* < MMC1 Clock enable */
-#define CKEN_MMC2	13	/* < MMC2 clock enable */
-#define CKEN_KEYPAD	14	/* < Keypand Controller Clock Enable */
-#define CKEN_CIR	15	/* < Consumer IR Clock Enable */
-#define CKEN_USIM0	17	/* < USIM[0] Clock Enable */
-#define CKEN_USIM1	18	/* < USIM[1] Clock Enable */
-#define CKEN_TPM	19	/* < TPM clock enable */
-#define CKEN_UDC	20	/* < UDC clock enable */
-#define CKEN_BTUART	21	/* < BTUART clock enable */
-#define CKEN_FFUART	22	/* < FFUART clock enable */
-#define CKEN_STUART	23	/* < STUART clock enable */
-#define CKEN_AC97	24	/* < AC97 clock enable */
-#define CKEN_TOUCH	25	/* < Touch screen Interface Clock Enable */
-#define CKEN_SSP1	26	/* < SSP1 clock enable */
-#define CKEN_SSP2	27	/* < SSP2 clock enable */
-#define CKEN_SSP3	28	/* < SSP3 clock enable */
-#define CKEN_SSP4	29	/* < SSP4 clock enable */
-#define CKEN_MSL0	30	/* < MSL0 clock enable */
-#define CKEN_PWM0	32	/* < PWM[0] clock enable */
-#define CKEN_PWM1	33	/* < PWM[1] clock enable */
-#define CKEN_I2C	36	/* < I2C clock enable */
-#define CKEN_INTC	38	/* < Interrupt controller clock enable */
-#define CKEN_GPIO	39	/* < GPIO clock enable */
-#define CKEN_1WIRE	40	/* < 1-wire clock enable */
-#define CKEN_HSIO2	41	/* < HSIO2 clock enable */
-#define CKEN_MINI_IM	48	/* < Mini-IM */
-#define CKEN_MINI_LCD	49	/* < Mini LCD */
-
-#define CKEN_MMC3	5	/* < MMC3 Clock Enable */
-#define CKEN_MVED	43	/* < MVED clock enable */
-
-/* Note: GCU clock enable bit differs on PXA300/PXA310 and PXA320 */
-#define CKEN_PXA300_GCU		42	/* Graphics controller clock enable */
-#define CKEN_PXA320_GCU		7	/* Graphics controller clock enable */
-
-#endif /* __ASM_ARCH_PXA3XX_REGS_H */
diff --git a/arch/arm/mach-pxa/include/mach/regs-ac97.h b/arch/arm/mach-pxa/include/mach/regs-ac97.h
deleted file mode 100644
index 1db96fd4df32..000000000000
--- a/arch/arm/mach-pxa/include/mach/regs-ac97.h
+++ /dev/null
@@ -1,102 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-#ifndef __ASM_ARCH_REGS_AC97_H
-#define __ASM_ARCH_REGS_AC97_H
-
-#include <mach/hardware.h>
-
-/*
- * AC97 Controller registers
- */
-
-#define POCR		__REG(0x40500000)  /* PCM Out Control Register */
-#define POCR_FEIE	(1 << 3)	/* FIFO Error Interrupt Enable */
-#define POCR_FSRIE	(1 << 1)	/* FIFO Service Request Interrupt Enable */
-
-#define PICR		__REG(0x40500004)  /* PCM In Control Register */
-#define PICR_FEIE	(1 << 3)	/* FIFO Error Interrupt Enable */
-#define PICR_FSRIE	(1 << 1)	/* FIFO Service Request Interrupt Enable */
-
-#define MCCR		__REG(0x40500008)  /* Mic In Control Register */
-#define MCCR_FEIE	(1 << 3)	/* FIFO Error Interrupt Enable */
-#define MCCR_FSRIE	(1 << 1)	/* FIFO Service Request Interrupt Enable */
-
-#define GCR		__REG(0x4050000C)  /* Global Control Register */
-#ifdef CONFIG_PXA3xx
-#define GCR_CLKBPB	(1 << 31)	/* Internal clock enable */
-#endif
-#define GCR_nDMAEN	(1 << 24)	/* non DMA Enable */
-#define GCR_CDONE_IE	(1 << 19)	/* Command Done Interrupt Enable */
-#define GCR_SDONE_IE	(1 << 18)	/* Status Done Interrupt Enable */
-#define GCR_SECRDY_IEN	(1 << 9)	/* Secondary Ready Interrupt Enable */
-#define GCR_PRIRDY_IEN	(1 << 8)	/* Primary Ready Interrupt Enable */
-#define GCR_SECRES_IEN	(1 << 5)	/* Secondary Resume Interrupt Enable */
-#define GCR_PRIRES_IEN	(1 << 4)	/* Primary Resume Interrupt Enable */
-#define GCR_ACLINK_OFF	(1 << 3)	/* AC-link Shut Off */
-#define GCR_WARM_RST	(1 << 2)	/* AC97 Warm Reset */
-#define GCR_COLD_RST	(1 << 1)	/* AC'97 Cold Reset (0 = active) */
-#define GCR_GIE		(1 << 0)	/* Codec GPI Interrupt Enable */
-
-#define POSR		__REG(0x40500010)  /* PCM Out Status Register */
-#define POSR_FIFOE	(1 << 4)	/* FIFO error */
-#define POSR_FSR	(1 << 2)	/* FIFO Service Request */
-
-#define PISR		__REG(0x40500014)  /* PCM In Status Register */
-#define PISR_FIFOE	(1 << 4)	/* FIFO error */
-#define PISR_EOC	(1 << 3)	/* DMA End-of-Chain (exclusive clear) */
-#define PISR_FSR	(1 << 2)	/* FIFO Service Request */
-
-#define MCSR		__REG(0x40500018)  /* Mic In Status Register */
-#define MCSR_FIFOE	(1 << 4)	/* FIFO error */
-#define MCSR_EOC	(1 << 3)	/* DMA End-of-Chain (exclusive clear) */
-#define MCSR_FSR	(1 << 2)	/* FIFO Service Request */
-
-#define GSR		__REG(0x4050001C)  /* Global Status Register */
-#define GSR_CDONE	(1 << 19)	/* Command Done */
-#define GSR_SDONE	(1 << 18)	/* Status Done */
-#define GSR_RDCS	(1 << 15)	/* Read Completion Status */
-#define GSR_BIT3SLT12	(1 << 14)	/* Bit 3 of slot 12 */
-#define GSR_BIT2SLT12	(1 << 13)	/* Bit 2 of slot 12 */
-#define GSR_BIT1SLT12	(1 << 12)	/* Bit 1 of slot 12 */
-#define GSR_SECRES	(1 << 11)	/* Secondary Resume Interrupt */
-#define GSR_PRIRES	(1 << 10)	/* Primary Resume Interrupt */
-#define GSR_SCR		(1 << 9)	/* Secondary Codec Ready */
-#define GSR_PCR		(1 << 8)	/*  Primary Codec Ready */
-#define GSR_MCINT	(1 << 7)	/* Mic In Interrupt */
-#define GSR_POINT	(1 << 6)	/* PCM Out Interrupt */
-#define GSR_PIINT	(1 << 5)	/* PCM In Interrupt */
-#define GSR_ACOFFD	(1 << 3)	/* AC-link Shut Off Done */
-#define GSR_MOINT	(1 << 2)	/* Modem Out Interrupt */
-#define GSR_MIINT	(1 << 1)	/* Modem In Interrupt */
-#define GSR_GSCI	(1 << 0)	/* Codec GPI Status Change Interrupt */
-
-#define CAR		__REG(0x40500020)  /* CODEC Access Register */
-#define CAR_CAIP	(1 << 0)	/* Codec Access In Progress */
-
-#define PCDR		__REG(0x40500040)  /* PCM FIFO Data Register */
-#define MCDR		__REG(0x40500060)  /* Mic-in FIFO Data Register */
-
-#define MOCR		__REG(0x40500100)  /* Modem Out Control Register */
-#define MOCR_FEIE	(1 << 3)	/* FIFO Error */
-#define MOCR_FSRIE	(1 << 1)	/* FIFO Service Request Interrupt Enable */
-
-#define MICR		__REG(0x40500108)  /* Modem In Control Register */
-#define MICR_FEIE	(1 << 3)	/* FIFO Error */
-#define MICR_FSRIE	(1 << 1)	/* FIFO Service Request Interrupt Enable */
-
-#define MOSR		__REG(0x40500110)  /* Modem Out Status Register */
-#define MOSR_FIFOE	(1 << 4)	/* FIFO error */
-#define MOSR_FSR	(1 << 2)	/* FIFO Service Request */
-
-#define MISR		__REG(0x40500118)  /* Modem In Status Register */
-#define MISR_FIFOE	(1 << 4)	/* FIFO error */
-#define MISR_EOC	(1 << 3)	/* DMA End-of-Chain (exclusive clear) */
-#define MISR_FSR	(1 << 2)	/* FIFO Service Request */
-
-#define MODR		__REG(0x40500140)  /* Modem FIFO Data Register */
-
-#define PAC_REG_BASE	__REG(0x40500200)  /* Primary Audio Codec */
-#define SAC_REG_BASE	__REG(0x40500300)  /* Secondary Audio Codec */
-#define PMC_REG_BASE	__REG(0x40500400)  /* Primary Modem Codec */
-#define SMC_REG_BASE	__REG(0x40500500)  /* Secondary Modem Codec */
-
-#endif /* __ASM_ARCH_REGS_AC97_H */
diff --git a/arch/arm/mach-pxa/include/mach/regs-lcd.h b/arch/arm/mach-pxa/include/mach/regs-lcd.h
deleted file mode 100644
index e2b6e3d1f625..000000000000
--- a/arch/arm/mach-pxa/include/mach/regs-lcd.h
+++ /dev/null
@@ -1,198 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-#ifndef __ASM_ARCH_REGS_LCD_H
-#define __ASM_ARCH_REGS_LCD_H
-
-#include <mach/bitfield.h>
-
-/*
- * LCD Controller Registers and Bits Definitions
- */
-#define LCCR0		(0x000)	/* LCD Controller Control Register 0 */
-#define LCCR1		(0x004)	/* LCD Controller Control Register 1 */
-#define LCCR2		(0x008)	/* LCD Controller Control Register 2 */
-#define LCCR3		(0x00C)	/* LCD Controller Control Register 3 */
-#define LCCR4		(0x010)	/* LCD Controller Control Register 4 */
-#define LCCR5		(0x014)	/* LCD Controller Control Register 5 */
-#define LCSR		(0x038)	/* LCD Controller Status Register 0 */
-#define LCSR1		(0x034)	/* LCD Controller Status Register 1 */
-#define LIIDR		(0x03C)	/* LCD Controller Interrupt ID Register */
-#define TMEDRGBR	(0x040)	/* TMED RGB Seed Register */
-#define TMEDCR		(0x044)	/* TMED Control Register */
-
-#define FBR0		(0x020)	/* DMA Channel 0 Frame Branch Register */
-#define FBR1		(0x024)	/* DMA Channel 1 Frame Branch Register */
-#define FBR2		(0x028) /* DMA Channel 2 Frame Branch Register */
-#define FBR3		(0x02C) /* DMA Channel 2 Frame Branch Register */
-#define FBR4		(0x030) /* DMA Channel 2 Frame Branch Register */
-#define FBR5		(0x110) /* DMA Channel 2 Frame Branch Register */
-#define FBR6		(0x114) /* DMA Channel 2 Frame Branch Register */
-
-#define OVL1C1		(0x050)	/* Overlay 1 Control Register 1 */
-#define OVL1C2		(0x060)	/* Overlay 1 Control Register 2 */
-#define OVL2C1		(0x070)	/* Overlay 2 Control Register 1 */
-#define OVL2C2		(0x080)	/* Overlay 2 Control Register 2 */
-
-#define CMDCR		(0x100)	/* Command Control Register */
-#define PRSR		(0x104)	/* Panel Read Status Register */
-
-#define LCCR3_BPP(x)	((((x) & 0x7) << 24) | (((x) & 0x8) ? (1 << 29) : 0))
-
-#define LCCR3_PDFOR_0	(0 << 30)
-#define LCCR3_PDFOR_1	(1 << 30)
-#define LCCR3_PDFOR_2	(2 << 30)
-#define LCCR3_PDFOR_3	(3 << 30)
-
-#define LCCR4_PAL_FOR_0	(0 << 15)
-#define LCCR4_PAL_FOR_1	(1 << 15)
-#define LCCR4_PAL_FOR_2	(2 << 15)
-#define LCCR4_PAL_FOR_3	(3 << 15)
-#define LCCR4_PAL_FOR_MASK	(3 << 15)
-
-#define FDADR0		(0x200)	/* DMA Channel 0 Frame Descriptor Address Register */
-#define FDADR1		(0x210)	/* DMA Channel 1 Frame Descriptor Address Register */
-#define FDADR2		(0x220)	/* DMA Channel 2 Frame Descriptor Address Register */
-#define FDADR3		(0x230)	/* DMA Channel 3 Frame Descriptor Address Register */
-#define FDADR4		(0x240)	/* DMA Channel 4 Frame Descriptor Address Register */
-#define FDADR5		(0x250)	/* DMA Channel 5 Frame Descriptor Address Register */
-#define FDADR6		(0x260) /* DMA Channel 6 Frame Descriptor Address Register */
-
-#define LCCR0_ENB	(1 << 0)	/* LCD Controller enable */
-#define LCCR0_CMS	(1 << 1)	/* Color/Monochrome Display Select */
-#define LCCR0_Color	(LCCR0_CMS*0)	/*  Color display */
-#define LCCR0_Mono	(LCCR0_CMS*1)	/*  Monochrome display */
-#define LCCR0_SDS	(1 << 2)	/* Single/Dual Panel Display Select */
-#define LCCR0_Sngl	(LCCR0_SDS*0)	/*  Single panel display */
-#define LCCR0_Dual	(LCCR0_SDS*1)	/*  Dual panel display */
-
-#define LCCR0_LDM	(1 << 3)	/* LCD Disable Done Mask */
-#define LCCR0_SFM	(1 << 4)	/* Start of frame mask */
-#define LCCR0_IUM	(1 << 5)	/* Input FIFO underrun mask */
-#define LCCR0_EFM	(1 << 6)	/* End of Frame mask */
-#define LCCR0_PAS	(1 << 7)	/* Passive/Active display Select */
-#define LCCR0_Pas	(LCCR0_PAS*0)	/*  Passive display (STN) */
-#define LCCR0_Act	(LCCR0_PAS*1)	/*  Active display (TFT) */
-#define LCCR0_DPD	(1 << 9)	/* Double Pixel Data (monochrome) */
-#define LCCR0_4PixMono	(LCCR0_DPD*0)	/*  4-Pixel/clock Monochrome display */
-#define LCCR0_8PixMono	(LCCR0_DPD*1)	/*  8-Pixel/clock Monochrome display */
-#define LCCR0_DIS	(1 << 10)	/* LCD Disable */
-#define LCCR0_QDM	(1 << 11)	/* LCD Quick Disable mask */
-#define LCCR0_PDD	(0xff << 12)	/* Palette DMA request delay */
-#define LCCR0_PDD_S	12
-#define LCCR0_BM	(1 << 20)	/* Branch mask */
-#define LCCR0_OUM	(1 << 21)	/* Output FIFO underrun mask */
-#define LCCR0_LCDT	(1 << 22)	/* LCD panel type */
-#define LCCR0_RDSTM	(1 << 23)	/* Read status interrupt mask */
-#define LCCR0_CMDIM	(1 << 24)	/* Command interrupt mask */
-#define LCCR0_OUC	(1 << 25)	/* Overlay Underlay control bit */
-#define LCCR0_LDDALT	(1 << 26)	/* LDD alternate mapping control */
-
-#define LCCR1_PPL	Fld (10, 0)	/* Pixels Per Line - 1 */
-#define LCCR1_DisWdth(Pixel)	(((Pixel) - 1) << FShft (LCCR1_PPL))
-
-#define LCCR1_HSW	Fld (6, 10)	/* Horizontal Synchronization */
-#define LCCR1_HorSnchWdth(Tpix)	(((Tpix) - 1) << FShft (LCCR1_HSW))
-
-#define LCCR1_ELW	Fld (8, 16)	/* End-of-Line pixel clock Wait - 1 */
-#define LCCR1_EndLnDel(Tpix)	(((Tpix) - 1) << FShft (LCCR1_ELW))
-
-#define LCCR1_BLW	Fld (8, 24)	/* Beginning-of-Line pixel clock */
-#define LCCR1_BegLnDel(Tpix)	(((Tpix) - 1) << FShft (LCCR1_BLW))
-
-#define LCCR2_LPP	Fld (10, 0)	/* Line Per Panel - 1 */
-#define LCCR2_DisHght(Line)	(((Line) - 1) << FShft (LCCR2_LPP))
-
-#define LCCR2_VSW	Fld (6, 10)	/* Vertical Synchronization pulse - 1 */
-#define LCCR2_VrtSnchWdth(Tln)	(((Tln) - 1) << FShft (LCCR2_VSW))
-
-#define LCCR2_EFW	Fld (8, 16)	/* End-of-Frame line clock Wait */
-#define LCCR2_EndFrmDel(Tln)	((Tln) << FShft (LCCR2_EFW))
-
-#define LCCR2_BFW	Fld (8, 24)	/* Beginning-of-Frame line clock */
-#define LCCR2_BegFrmDel(Tln)	((Tln) << FShft (LCCR2_BFW))
-
-#define LCCR3_API	(0xf << 16)	/* AC Bias pin trasitions per interrupt */
-#define LCCR3_API_S	16
-#define LCCR3_VSP	(1 << 20)	/* vertical sync polarity */
-#define LCCR3_HSP	(1 << 21)	/* horizontal sync polarity */
-#define LCCR3_PCP	(1 << 22)	/* Pixel Clock Polarity (L_PCLK) */
-#define LCCR3_PixRsEdg	(LCCR3_PCP*0)	/*  Pixel clock Rising-Edge */
-#define LCCR3_PixFlEdg	(LCCR3_PCP*1)	/*  Pixel clock Falling-Edge */
-
-#define LCCR3_OEP	(1 << 23)	/* Output Enable Polarity */
-#define LCCR3_OutEnH	(LCCR3_OEP*0)	/*  Output Enable active High */
-#define LCCR3_OutEnL	(LCCR3_OEP*1)	/*  Output Enable active Low */
-
-#define LCCR3_DPC	(1 << 27)	/* double pixel clock mode */
-#define LCCR3_PCD	Fld (8, 0)	/* Pixel Clock Divisor */
-#define LCCR3_PixClkDiv(Div)	(((Div) << FShft (LCCR3_PCD)))
-
-#define LCCR3_ACB	Fld (8, 8)	/* AC Bias */
-#define LCCR3_Acb(Acb)	(((Acb) << FShft (LCCR3_ACB)))
-
-#define LCCR3_HorSnchH	(LCCR3_HSP*0)	/*  HSP Active High */
-#define LCCR3_HorSnchL	(LCCR3_HSP*1)	/*  HSP Active Low */
-
-#define LCCR3_VrtSnchH	(LCCR3_VSP*0)	/*  VSP Active High */
-#define LCCR3_VrtSnchL	(LCCR3_VSP*1)	/*  VSP Active Low */
-
-#define LCCR5_IUM(x)	(1 << ((x) + 23)) /* input underrun mask */
-#define LCCR5_BSM(x)	(1 << ((x) + 15)) /* branch mask */
-#define LCCR5_EOFM(x)	(1 << ((x) + 7))  /* end of frame mask */
-#define LCCR5_SOFM(x)	(1 << ((x) + 0))  /* start of frame mask */
-
-#define LCSR_LDD	(1 << 0)	/* LCD Disable Done */
-#define LCSR_SOF	(1 << 1)	/* Start of frame */
-#define LCSR_BER	(1 << 2)	/* Bus error */
-#define LCSR_ABC	(1 << 3)	/* AC Bias count */
-#define LCSR_IUL	(1 << 4)	/* input FIFO underrun Lower panel */
-#define LCSR_IUU	(1 << 5)	/* input FIFO underrun Upper panel */
-#define LCSR_OU		(1 << 6)	/* output FIFO underrun */
-#define LCSR_QD		(1 << 7)	/* quick disable */
-#define LCSR_EOF	(1 << 8)	/* end of frame */
-#define LCSR_BS		(1 << 9)	/* branch status */
-#define LCSR_SINT	(1 << 10)	/* subsequent interrupt */
-#define LCSR_RD_ST	(1 << 11)	/* read status */
-#define LCSR_CMD_INT	(1 << 12)	/* command interrupt */
-
-#define LCSR1_IU(x)	(1 << ((x) + 23)) /* Input FIFO underrun */
-#define LCSR1_BS(x)	(1 << ((x) + 15)) /* Branch Status */
-#define LCSR1_EOF(x)	(1 << ((x) + 7))  /* End of Frame Status */
-#define LCSR1_SOF(x)	(1 << ((x) - 1))  /* Start of Frame Status */
-
-#define LDCMD_PAL	(1 << 26)	/* instructs DMA to load palette buffer */
-
-/* overlay control registers */
-#define OVLxC1_PPL(x)	((((x) - 1) & 0x3ff) << 0)	/* Pixels Per Line */
-#define OVLxC1_LPO(x)	((((x) - 1) & 0x3ff) << 10)	/* Number of Lines */
-#define OVLxC1_BPP(x)	(((x) & 0xf) << 20)	/* Bits Per Pixel */
-#define OVLxC1_OEN	(1 << 31)		/* Enable bit for Overlay */
-#define OVLxC2_XPOS(x)	(((x) & 0x3ff) << 0)	/* Horizontal Position */
-#define OVLxC2_YPOS(x)	(((x) & 0x3ff) << 10)	/* Vertical Position */
-#define OVL2C2_PFOR(x)	(((x) & 0x7) << 20)	/* Pixel Format */
-
-/* smartpanel related */
-#define PRSR_DATA(x)	((x) & 0xff)	/* Panel Data */
-#define PRSR_A0		(1 << 8)	/* Read Data Source */
-#define PRSR_ST_OK	(1 << 9)	/* Status OK */
-#define PRSR_CON_NT	(1 << 10)	/* Continue to Next Command */
-
-#define SMART_CMD_A0			 (0x1 << 8)
-#define SMART_CMD_READ_STATUS_REG	 (0x0 << 9)
-#define SMART_CMD_READ_FRAME_BUFFER	((0x0 << 9) | SMART_CMD_A0)
-#define SMART_CMD_WRITE_COMMAND		 (0x1 << 9)
-#define SMART_CMD_WRITE_DATA		((0x1 << 9) | SMART_CMD_A0)
-#define SMART_CMD_WRITE_FRAME		((0x2 << 9) | SMART_CMD_A0)
-#define SMART_CMD_WAIT_FOR_VSYNC	 (0x3 << 9)
-#define SMART_CMD_NOOP			 (0x4 << 9)
-#define SMART_CMD_INTERRUPT		 (0x5 << 9)
-
-#define SMART_CMD(x)	(SMART_CMD_WRITE_COMMAND | ((x) & 0xff))
-#define SMART_DAT(x)	(SMART_CMD_WRITE_DATA | ((x) & 0xff))
-
-/* SMART_DELAY() is introduced for software controlled delay primitive which
- * can be inserted between command sequences, unused command 0x6 is used here
- * and delay ranges from 0ms ~ 255ms
- */
-#define SMART_CMD_DELAY		(0x6 << 9)
-#define SMART_DELAY(ms)		(SMART_CMD_DELAY | ((ms) & 0xff))
-#endif /* __ASM_ARCH_REGS_LCD_H */
diff --git a/arch/arm/mach-pxa/include/mach/reset.h b/arch/arm/mach-pxa/include/mach/reset.h
deleted file mode 100644
index e1c4d100fd45..000000000000
--- a/arch/arm/mach-pxa/include/mach/reset.h
+++ /dev/null
@@ -1,22 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-#ifndef __ASM_ARCH_RESET_H
-#define __ASM_ARCH_RESET_H
-
-#define RESET_STATUS_HARDWARE	(1 << 0)	/* Hardware Reset */
-#define RESET_STATUS_WATCHDOG	(1 << 1)	/* Watchdog Reset */
-#define RESET_STATUS_LOWPOWER	(1 << 2)	/* Low Power/Sleep Exit */
-#define RESET_STATUS_GPIO	(1 << 3)	/* GPIO Reset */
-#define RESET_STATUS_ALL	(0xf)
-
-extern unsigned int reset_status;
-extern void clear_reset_status(unsigned int mask);
-
-/**
- * init_gpio_reset() - register GPIO as reset generator
- * @gpio: gpio nr
- * @output: set gpio as output instead of input during normal work
- * @level: output level
- */
-extern int init_gpio_reset(int gpio, int output, int level);
-
-#endif /* __ASM_ARCH_RESET_H */
diff --git a/arch/arm/mach-pxa/include/mach/uncompress.h b/arch/arm/mach-pxa/include/mach/uncompress.h
deleted file mode 100644
index c36306064eee..000000000000
--- a/arch/arm/mach-pxa/include/mach/uncompress.h
+++ /dev/null
@@ -1,71 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-only */
-/*
- * arch/arm/mach-pxa/include/mach/uncompress.h
- *
- * Author:	Nicolas Pitre
- * Copyright:	(C) 2001 MontaVista Software Inc.
- */
-
-#include <linux/serial_reg.h>
-#include <asm/mach-types.h>
-
-#define FFUART_BASE	(0x40100000)
-#define BTUART_BASE	(0x40200000)
-#define STUART_BASE	(0x40700000)
-
-unsigned long uart_base;
-unsigned int uart_shift;
-unsigned int uart_is_pxa;
-
-static inline unsigned char uart_read(int offset)
-{
-	return *(volatile unsigned char *)(uart_base + (offset << uart_shift));
-}
-
-static inline void uart_write(unsigned char val, int offset)
-{
-	*(volatile unsigned char *)(uart_base + (offset << uart_shift)) = val;
-}
-
-static inline int uart_is_enabled(void)
-{
-	/* assume enabled by default for non-PXA uarts */
-	return uart_is_pxa ? uart_read(UART_IER) & UART_IER_UUE : 1;
-}
-
-static inline void putc(char c)
-{
-	if (!uart_is_enabled())
-		return;
-
-	while (!(uart_read(UART_LSR) & UART_LSR_THRE))
-		barrier();
-
-	uart_write(c, UART_TX);
-}
-
-/*
- * This does not append a newline
- */
-static inline void flush(void)
-{
-}
-
-static inline void arch_decomp_setup(void)
-{
-	/* initialize to default */
-	uart_base = FFUART_BASE;
-	uart_shift = 2;
-	uart_is_pxa = 1;
-
-	if (machine_is_littleton() || machine_is_intelmote2()
-	    || machine_is_csb726() || machine_is_stargate2()
-	    || machine_is_cm_x300() || machine_is_balloon3())
-		uart_base = STUART_BASE;
-
-	if (machine_is_arcom_zeus()) {
-		uart_base = 0x10000000;	/* nCS4 */
-		uart_shift = 1;
-		uart_is_pxa = 0;
-	}
-}
diff --git a/arch/arm/mach-pxa/irq.c b/arch/arm/mach-pxa/irq.c
index 74efc3ab595f..96f33ef1d9ea 100644
--- a/arch/arm/mach-pxa/irq.c
+++ b/arch/arm/mach-pxa/irq.c
@@ -17,13 +17,14 @@
 #include <linux/irq.h>
 #include <linux/of_address.h>
 #include <linux/of_irq.h>
+#include <linux/soc/pxa/cpu.h>
 
 #include <asm/exception.h>
 
-#include <mach/hardware.h>
-#include <mach/irqs.h>
+#include "irqs.h"
 
 #include "generic.h"
+#include "pxa-regs.h"
 
 #define ICIP			(0x000)
 #define ICMR			(0x004)
diff --git a/arch/arm/mach-pxa/include/mach/irqs.h b/arch/arm/mach-pxa/irqs.h
index 22bf536a462d..22bf536a462d 100644
--- a/arch/arm/mach-pxa/include/mach/irqs.h
+++ b/arch/arm/mach-pxa/irqs.h
diff --git a/arch/arm/mach-pxa/littleton.c b/arch/arm/mach-pxa/littleton.c
index 793f61375ee8..98423a96f440 100644
--- a/arch/arm/mach-pxa/littleton.c
+++ b/arch/arm/mach-pxa/littleton.c
@@ -31,7 +31,6 @@
 #include <asm/setup.h>
 #include <asm/memory.h>
 #include <asm/mach-types.h>
-#include <mach/hardware.h>
 #include <asm/irq.h>
 
 #include <asm/mach/arch.h>
@@ -195,7 +194,6 @@ static struct pxa2xx_spi_controller littleton_spi_info = {
 static struct pxa2xx_spi_chip littleton_tdo24m_chip = {
 	.rx_threshold	= 1,
 	.tx_threshold	= 1,
-	.gpio_cs	= LITTLETON_GPIO_LCD_CS,
 };
 
 static struct spi_board_info littleton_spi_devices[] __initdata = {
@@ -208,8 +206,17 @@ static struct spi_board_info littleton_spi_devices[] __initdata = {
 	},
 };
 
+static struct gpiod_lookup_table littleton_spi_gpio_table = {
+	.dev_id = "spi2",
+	.table = {
+		GPIO_LOOKUP_IDX("gpio-pxa", LITTLETON_GPIO_LCD_CS, "cs", 0, GPIO_ACTIVE_LOW),
+		{ },
+	},
+};
+
 static void __init littleton_init_spi(void)
 {
+	gpiod_add_lookup_table(&littleton_spi_gpio_table);
 	pxa2xx_set_spi_info(2, &littleton_spi_info);
 	spi_register_board_info(ARRAY_AND_SIZE(littleton_spi_devices));
 }
diff --git a/arch/arm/mach-pxa/lpd270.c b/arch/arm/mach-pxa/lpd270.c
index 6fc40bc06910..0e4123c5fd42 100644
--- a/arch/arm/mach-pxa/lpd270.c
+++ b/arch/arm/mach-pxa/lpd270.c
@@ -28,7 +28,6 @@
 #include <asm/setup.h>
 #include <asm/memory.h>
 #include <asm/mach-types.h>
-#include <mach/hardware.h>
 #include <asm/irq.h>
 #include <linux/sizes.h>
 
@@ -39,12 +38,13 @@
 
 #include "pxa27x.h"
 #include "lpd270.h"
-#include <mach/audio.h>
+#include "addr-map.h"
+#include <linux/platform_data/asoc-pxa.h>
 #include <linux/platform_data/video-pxafb.h>
 #include <linux/platform_data/mmc-pxamci.h>
 #include <linux/platform_data/irda-pxaficp.h>
 #include <linux/platform_data/usb-ohci-pxa27x.h>
-#include <mach/smemc.h>
+#include "smemc.h"
 
 #include "generic.h"
 #include "devices.h"
diff --git a/arch/arm/mach-pxa/lubbock.c b/arch/arm/mach-pxa/lubbock.c
index 742d18a1f7dc..4f0944f3b262 100644
--- a/arch/arm/mach-pxa/lubbock.c
+++ b/arch/arm/mach-pxa/lubbock.c
@@ -34,7 +34,6 @@
 #include <asm/setup.h>
 #include <asm/memory.h>
 #include <asm/mach-types.h>
-#include <mach/hardware.h>
 #include <asm/irq.h>
 #include <linux/sizes.h>
 
@@ -46,14 +45,14 @@
 #include <asm/hardware/sa1111.h>
 
 #include "pxa25x.h"
-#include <mach/audio.h>
-#include <mach/lubbock.h>
+#include <linux/platform_data/asoc-pxa.h>
+#include "lubbock.h"
 #include "udc.h"
 #include <linux/platform_data/irda-pxaficp.h>
 #include <linux/platform_data/video-pxafb.h>
 #include <linux/platform_data/mmc-pxamci.h>
 #include "pm.h"
-#include <mach/smemc.h>
+#include "smemc.h"
 
 #include "generic.h"
 #include "devices.h"
@@ -132,6 +131,13 @@ static struct pxa2xx_udc_mach_info udc_info __initdata = {
 	// no D+ pullup; lubbock can't connect/disconnect in software
 };
 
+static struct resource lubbock_udc_resources[] = {
+	DEFINE_RES_MEM(0x40600000, 0x10000),
+	DEFINE_RES_IRQ(IRQ_USB),
+	DEFINE_RES_IRQ(LUBBOCK_USB_IRQ),
+	DEFINE_RES_IRQ(LUBBOCK_USB_DISC_IRQ),
+};
+
 /* GPIOs for SA1111 PCMCIA */
 static struct gpiod_lookup_table sa1111_pcmcia_gpio_table = {
 	.dev_id = "1800",
@@ -211,16 +217,17 @@ static struct ads7846_platform_data ads_info = {
 	// .y_plate_ohms		= 500,	/* GUESS! */
 };
 
-static void ads7846_cs(u32 command)
-{
-	static const unsigned	TS_nCS = 1 << 11;
-	lubbock_set_misc_wr(TS_nCS, (command == PXA2XX_CS_ASSERT) ? 0 : TS_nCS);
-}
+static struct gpiod_lookup_table ads7846_cs_gpios = {
+	.dev_id		= "ads7846",
+	.table		= {
+		GPIO_LOOKUP("lubbock", 11, "cs", GPIO_ACTIVE_LOW),
+		{}
+	},
+};
 
 static struct pxa2xx_spi_chip ads_hw = {
 	.tx_threshold		= 1,
 	.rx_threshold		= 2,
-	.cs_control		= ads7846_cs,
 };
 
 static struct spi_board_info spi_board_info[] __initdata = { {
@@ -496,6 +503,9 @@ static void __init lubbock_init(void)
 	lubbock_init_pcmcia();
 
 	clk_add_alias("SA1111_CLK", NULL, "GPIO11_CLK", NULL);
+	/* lubbock has two extra IRQs */
+	pxa25x_device_udc.resource = lubbock_udc_resources;
+	pxa25x_device_udc.num_resources = ARRAY_SIZE(lubbock_udc_resources);
 	pxa_set_udc_info(&udc_info);
 	pxa_set_fb_info(NULL, &sharp_lm8v31);
 	pxa_set_mci_info(&lubbock_mci_platform_data);
@@ -512,6 +522,8 @@ static void __init lubbock_init(void)
 	lubbock_flash_data[flashboot].name = "boot-rom";
 	(void) platform_add_devices(devices, ARRAY_SIZE(devices));
 
+	gpiod_add_lookup_table(&ads7846_cs_gpios);
+
 	pxa2xx_set_spi_info(1, &pxa_ssp_master_info);
 	spi_register_board_info(spi_board_info, ARRAY_SIZE(spi_board_info));
 }
diff --git a/arch/arm/mach-pxa/include/mach/lubbock.h b/arch/arm/mach-pxa/lubbock.h
index a3af4a2f9446..55cf91e22ae2 100644
--- a/arch/arm/mach-pxa/include/mach/lubbock.h
+++ b/arch/arm/mach-pxa/lubbock.h
@@ -1,13 +1,11 @@
 /* SPDX-License-Identifier: GPL-2.0-only */
 /*
- *  arch/arm/mach-pxa/include/mach/lubbock.h
- *
  *  Author:	Nicolas Pitre
  *  Created:	Jun 15, 2001
  *  Copyright:	MontaVista Software Inc.
  */
 
-#include <mach/irqs.h>
+#include "irqs.h"
 
 #define LUBBOCK_ETH_PHYS	PXA_CS3_PHYS
 
diff --git a/arch/arm/mach-pxa/magician.c b/arch/arm/mach-pxa/magician.c
index cd9fa465b9b2..0827ebca1d38 100644
--- a/arch/arm/mach-pxa/magician.c
+++ b/arch/arm/mach-pxa/magician.c
@@ -29,13 +29,13 @@
 #include <linux/regulator/machine.h>
 #include <linux/platform_data/i2c-pxa.h>
 
-#include <mach/hardware.h>
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
 #include <asm/system_info.h>
 
 #include "pxa27x.h"
-#include <mach/magician.h>
+#include "addr-map.h"
+#include "magician.h"
 #include <linux/platform_data/video-pxafb.h>
 #include <linux/platform_data/mmc-pxamci.h>
 #include <linux/platform_data/irda-pxaficp.h>
@@ -53,6 +53,7 @@
 #include <linux/spi/spi.h>
 #include <linux/spi/pxa2xx_spi.h>
 #include <linux/spi/ads7846.h>
+#include <sound/uda1380.h>
 
 static unsigned long magician_pin_config[] __initdata = {
 
@@ -681,7 +682,7 @@ static struct platform_device bq24022 = {
 static struct gpiod_lookup_table bq24022_gpiod_table = {
 	.dev_id = "gpio-regulator",
 	.table = {
-		GPIO_LOOKUP("gpio-pxa", EGPIO_MAGICIAN_BQ24022_ISET2,
+		GPIO_LOOKUP("htc-egpio-0", EGPIO_MAGICIAN_BQ24022_ISET2 - MAGICIAN_EGPIO_BASE,
 			    NULL, GPIO_ACTIVE_HIGH),
 		GPIO_LOOKUP("gpio-pxa", GPIO30_MAGICIAN_BQ24022_nCHARGE_EN,
 			    "enable", GPIO_ACTIVE_LOW),
@@ -899,6 +900,53 @@ static struct platform_device strataflash = {
 };
 
 /*
+ * audio support
+ */
+static struct uda1380_platform_data uda1380_info = {
+	.gpio_power = EGPIO_MAGICIAN_CODEC_POWER,
+	.gpio_reset = EGPIO_MAGICIAN_CODEC_RESET,
+	.dac_clk    = UDA1380_DAC_CLK_WSPLL,
+};
+
+static struct i2c_board_info magician_audio_i2c_board_info[] = {
+	{
+		I2C_BOARD_INFO("uda1380", 0x18),
+		.platform_data = &uda1380_info,
+	},
+};
+
+static struct gpiod_lookup_table magician_audio_gpio_table = {
+	.dev_id = "magician-audio",
+	.table = {
+		GPIO_LOOKUP("htc-egpio-0",
+			    EGPIO_MAGICIAN_SPK_POWER - MAGICIAN_EGPIO_BASE,
+			    "SPK_POWER", GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP("htc-egpio-0",
+			    EGPIO_MAGICIAN_EP_POWER - MAGICIAN_EGPIO_BASE,
+			    "EP_POWER", GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP("htc-egpio-0",
+			    EGPIO_MAGICIAN_MIC_POWER - MAGICIAN_EGPIO_BASE,
+			    "MIC_POWER", GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP("htc-egpio-0",
+			    EGPIO_MAGICIAN_IN_SEL0 - MAGICIAN_EGPIO_BASE,
+			    "IN_SEL0", GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP("htc-egpio-0",
+			    EGPIO_MAGICIAN_IN_SEL1 - MAGICIAN_EGPIO_BASE,
+			    "IN_SEL1", GPIO_ACTIVE_HIGH),
+		{ },
+	},
+};
+
+static void magician_audio_init(void)
+{
+	i2c_register_board_info(0,
+		ARRAY_AND_SIZE(magician_audio_i2c_board_info));
+
+	gpiod_add_lookup_table(&magician_audio_gpio_table);
+	platform_device_register_simple("magician-audio", -1, NULL, 0);
+}
+
+/*
  * PXA I2C main controller
  */
 
@@ -938,8 +986,6 @@ struct pxa2xx_spi_chip tsc2046_chip_info = {
 	.tx_threshold	= 1,
 	.rx_threshold	= 2,
 	.timeout	= 64,
-	/* NOTICE must be GPIO, incompatibility with hw PXA SPI framing */
-	.gpio_cs	= GPIO14_MAGICIAN_TSC2046_CS,
 };
 
 static struct pxa2xx_spi_controller magician_spi_info = {
@@ -947,6 +993,15 @@ static struct pxa2xx_spi_controller magician_spi_info = {
 	.enable_dma	= 1,
 };
 
+static struct gpiod_lookup_table magician_spi_gpio_table = {
+	.dev_id = "spi2",
+	.table = {
+		/* NOTICE must be GPIO, incompatibility with hw PXA SPI framing */
+		GPIO_LOOKUP_IDX("gpio-pxa", GPIO14_MAGICIAN_TSC2046_CS, "cs", 0, GPIO_ACTIVE_LOW),
+		{ },
+	},
+};
+
 static struct spi_board_info ads7846_spi_board_info[] __initdata = {
 	{
 		.modalias		= "ads7846",
@@ -1031,6 +1086,7 @@ static void __init magician_init(void)
 	} else
 		pr_err("LCD detection: CPLD mapping failed\n");
 
+	gpiod_add_lookup_table(&magician_spi_gpio_table);
 	pxa2xx_set_spi_info(2, &magician_spi_info);
 	spi_register_board_info(ARRAY_AND_SIZE(ads7846_spi_board_info));
 
@@ -1040,6 +1096,8 @@ static void __init magician_init(void)
 	gpiod_add_lookup_table(&bq24022_gpiod_table);
 	gpiod_add_lookup_table(&gpio_vbus_gpiod_table);
 	platform_add_devices(ARRAY_AND_SIZE(devices));
+
+	magician_audio_init();
 }
 
 MACHINE_START(MAGICIAN, "HTC Magician")
diff --git a/arch/arm/mach-pxa/include/mach/magician.h b/arch/arm/mach-pxa/magician.h
index 7d3af561af6f..e1e4f9f6b22b 100644
--- a/arch/arm/mach-pxa/include/mach/magician.h
+++ b/arch/arm/mach-pxa/magician.h
@@ -9,7 +9,7 @@
 #define _MAGICIAN_H_
 
 #include <linux/gpio.h>
-#include <mach/irqs.h>
+#include "irqs.h"
 
 /*
  * PXA GPIOs
diff --git a/arch/arm/mach-pxa/mainstone.c b/arch/arm/mach-pxa/mainstone.c
index d237bd030238..fd386f1c414c 100644
--- a/arch/arm/mach-pxa/mainstone.c
+++ b/arch/arm/mach-pxa/mainstone.c
@@ -35,7 +35,6 @@
 #include <asm/setup.h>
 #include <asm/memory.h>
 #include <asm/mach-types.h>
-#include <mach/hardware.h>
 #include <asm/irq.h>
 #include <linux/sizes.h>
 
@@ -45,14 +44,15 @@
 #include <asm/mach/flash.h>
 
 #include "pxa27x.h"
-#include <mach/mainstone.h>
-#include <mach/audio.h>
+#include "mainstone.h"
+#include <linux/platform_data/asoc-pxa.h>
 #include <linux/platform_data/video-pxafb.h>
 #include <linux/platform_data/mmc-pxamci.h>
 #include <linux/platform_data/irda-pxaficp.h>
 #include <linux/platform_data/usb-ohci-pxa27x.h>
 #include <linux/platform_data/keypad-pxa27x.h>
-#include <mach/smemc.h>
+#include "addr-map.h"
+#include "smemc.h"
 
 #include "generic.h"
 #include "devices.h"
@@ -548,6 +548,14 @@ static struct gpiod_lookup_table mainstone_pcmcia_gpio_table = {
 	},
 };
 
+static struct gpiod_lookup_table mainstone_wm97xx_gpio_table = {
+	.dev_id = "wm97xx-touch",
+	.table = {
+		GPIO_LOOKUP("gpio-pxa", 4, "touch", GPIO_ACTIVE_HIGH),
+		{ },
+	},
+};
+
 static void __init mainstone_init(void)
 {
 	int SW7 = 0;  /* FIXME: get from SCR (Mst doc section 3.2.1.1) */
@@ -562,6 +570,7 @@ static void __init mainstone_init(void)
 		      "mst-pcmcia1", MST_PCMCIA_INPUTS, 0, NULL,
 		      NULL, mst_pcmcia1_irqs);
 	gpiod_add_lookup_table(&mainstone_pcmcia_gpio_table);
+	gpiod_add_lookup_table(&mainstone_wm97xx_gpio_table);
 
 	pxa_set_ffuart_info(NULL);
 	pxa_set_btuart_info(NULL);
diff --git a/arch/arm/mach-pxa/include/mach/mainstone.h b/arch/arm/mach-pxa/mainstone.h
index 1698f2ffd7c7..f116c56cf5d9 100644
--- a/arch/arm/mach-pxa/include/mach/mainstone.h
+++ b/arch/arm/mach-pxa/mainstone.h
@@ -1,7 +1,5 @@
 /* SPDX-License-Identifier: GPL-2.0-only */
 /*
- *  arch/arm/mach-pxa/include/mach/mainstone.h
- *
  *  Author:	Nicolas Pitre
  *  Created:	Nov 14, 2002
  *  Copyright:	MontaVista Software Inc.
@@ -10,7 +8,7 @@
 #ifndef ASM_ARCH_MAINSTONE_H
 #define ASM_ARCH_MAINSTONE_H
 
-#include <mach/irqs.h>
+#include "irqs.h"
 
 #define MST_ETH_PHYS		PXA_CS4_PHYS
 
diff --git a/arch/arm/mach-pxa/mfp-pxa2xx.c b/arch/arm/mach-pxa/mfp-pxa2xx.c
index 6a5451b186c2..57b0782880de 100644
--- a/arch/arm/mach-pxa/mfp-pxa2xx.c
+++ b/arch/arm/mach-pxa/mfp-pxa2xx.c
@@ -16,8 +16,9 @@
 #include <linux/init.h>
 #include <linux/io.h>
 #include <linux/syscore_ops.h>
+#include <linux/soc/pxa/cpu.h>
 
-#include <mach/pxa2xx-regs.h>
+#include "pxa2xx-regs.h"
 #include "mfp-pxa2xx.h"
 
 #include "generic.h"
diff --git a/arch/arm/mach-pxa/mfp-pxa2xx.h b/arch/arm/mach-pxa/mfp-pxa2xx.h
index 980145e7ee99..683a3ea5f154 100644
--- a/arch/arm/mach-pxa/mfp-pxa2xx.h
+++ b/arch/arm/mach-pxa/mfp-pxa2xx.h
@@ -2,7 +2,7 @@
 #ifndef __ASM_ARCH_MFP_PXA2XX_H
 #define __ASM_ARCH_MFP_PXA2XX_H
 
-#include <plat/mfp.h>
+#include <linux/soc/pxa/mfp.h>
 
 /*
  * the following MFP_xxx bit definitions in mfp.h are re-used for pxa2xx:
diff --git a/arch/arm/mach-pxa/mfp-pxa3xx.c b/arch/arm/mach-pxa/mfp-pxa3xx.c
index 56114df9700d..d16ab7451efe 100644
--- a/arch/arm/mach-pxa/mfp-pxa3xx.c
+++ b/arch/arm/mach-pxa/mfp-pxa3xx.c
@@ -16,9 +16,8 @@
 #include <linux/io.h>
 #include <linux/syscore_ops.h>
 
-#include <mach/hardware.h>
 #include "mfp-pxa3xx.h"
-#include <mach/pxa3xx-regs.h>
+#include "pxa3xx-regs.h"
 
 #ifdef CONFIG_PM
 /*
diff --git a/arch/arm/mach-pxa/mfp-pxa3xx.h b/arch/arm/mach-pxa/mfp-pxa3xx.h
index cdd830926d1c..81fec4fa5a0f 100644
--- a/arch/arm/mach-pxa/mfp-pxa3xx.h
+++ b/arch/arm/mach-pxa/mfp-pxa3xx.h
@@ -2,7 +2,7 @@
 #ifndef __ASM_ARCH_MFP_PXA3XX_H
 #define __ASM_ARCH_MFP_PXA3XX_H
 
-#include <plat/mfp.h>
+#include <linux/soc/pxa/mfp.h>
 
 #define MFPR_BASE	(0x40e10000)
 
diff --git a/arch/arm/mach-pxa/mfp.h b/arch/arm/mach-pxa/mfp.h
new file mode 100644
index 000000000000..7e0879bd4102
--- /dev/null
+++ b/arch/arm/mach-pxa/mfp.h
@@ -0,0 +1,18 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * arch/arm/mach-pxa/include/mach/mfp.h
+ *
+ * Multi-Function Pin Definitions
+ *
+ * Copyright (C) 2007 Marvell International Ltd.
+ *
+ * 2007-8-21: eric miao <eric.miao@marvell.com>
+ *            initial version
+ */
+
+#ifndef __ASM_ARCH_MFP_H
+#define __ASM_ARCH_MFP_H
+
+#include <linux/soc/pxa/mfp.h>
+
+#endif /* __ASM_ARCH_MFP_H */
diff --git a/arch/arm/mach-pxa/mioa701.c b/arch/arm/mach-pxa/mioa701.c
index a79f296e81e0..d08f962ffb04 100644
--- a/arch/arm/mach-pxa/mioa701.c
+++ b/arch/arm/mach-pxa/mioa701.c
@@ -41,8 +41,8 @@
 #include "udc.h"
 #include "pxa27x-udc.h"
 #include <linux/platform_data/media/camera-pxa.h>
-#include <mach/audio.h>
-#include <mach/smemc.h>
+#include <linux/platform_data/asoc-pxa.h>
+#include "smemc.h"
 
 #include "mioa701.h"
 
diff --git a/arch/arm/mach-pxa/mxm8x10.c b/arch/arm/mach-pxa/mxm8x10.c
index fde386f6cffe..35546b59c88e 100644
--- a/arch/arm/mach-pxa/mxm8x10.c
+++ b/arch/arm/mach-pxa/mxm8x10.c
@@ -26,6 +26,7 @@
 #include <linux/platform_data/video-pxafb.h>
 #include <linux/platform_data/mmc-pxamci.h>
 #include <linux/platform_data/usb-ohci-pxa27x.h>
+#include <linux/platform_data/asoc-pxa.h>
 #include "pxa320.h"
 
 #include "mxm8x10.h"
@@ -356,14 +357,9 @@ void __init mxm_8x10_usb_host_init(void)
 	pxa_set_ohci_info(&mxm_8x10_ohci_platform_data);
 }
 
-/* AC97 Sound Support */
-static struct platform_device mxm_8x10_ac97_device = {
-	.name = "pxa2xx-ac97"
-};
-
 void __init mxm_8x10_ac97_init(void)
 {
-	platform_device_register(&mxm_8x10_ac97_device);
+	pxa_set_ac97_info(NULL);
 }
 
 /* NAND flash Support */
diff --git a/arch/arm/mach-pxa/palm27x.c b/arch/arm/mach-pxa/palm27x.c
index 6230381a7ca0..1a8d25eecac3 100644
--- a/arch/arm/mach-pxa/palm27x.c
+++ b/arch/arm/mach-pxa/palm27x.c
@@ -25,7 +25,7 @@
 #include <asm/mach/map.h>
 
 #include "pxa27x.h"
-#include <mach/audio.h>
+#include <linux/platform_data/asoc-pxa.h>
 #include <linux/platform_data/mmc-pxamci.h>
 #include <linux/platform_data/video-pxafb.h>
 #include <linux/platform_data/irda-pxaficp.h>
diff --git a/arch/arm/mach-pxa/palmld-pcmcia.c b/arch/arm/mach-pxa/palmld-pcmcia.c
new file mode 100644
index 000000000000..720294a50864
--- /dev/null
+++ b/arch/arm/mach-pxa/palmld-pcmcia.c
@@ -0,0 +1,111 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * linux/drivers/pcmcia/pxa2xx_palmld.c
+ *
+ * Driver for Palm LifeDrive PCMCIA
+ *
+ * Copyright (C) 2006 Alex Osborne <ato@meshy.org>
+ * Copyright (C) 2007-2011 Marek Vasut <marek.vasut@gmail.com>
+ */
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/gpio.h>
+
+#include <asm/mach-types.h>
+#include <pcmcia/soc_common.h>
+
+#include "palmld.h"
+
+static struct gpio palmld_pcmcia_gpios[] = {
+	{ GPIO_NR_PALMLD_PCMCIA_POWER,	GPIOF_INIT_LOW,	"PCMCIA Power" },
+	{ GPIO_NR_PALMLD_PCMCIA_RESET,	GPIOF_INIT_HIGH,"PCMCIA Reset" },
+};
+
+static int palmld_pcmcia_hw_init(struct soc_pcmcia_socket *skt)
+{
+	int ret;
+
+	ret = gpio_request_array(palmld_pcmcia_gpios,
+				ARRAY_SIZE(palmld_pcmcia_gpios));
+
+	skt->stat[SOC_STAT_RDY].gpio = GPIO_NR_PALMLD_PCMCIA_READY;
+	skt->stat[SOC_STAT_RDY].name = "PCMCIA Ready";
+
+	return ret;
+}
+
+static void palmld_pcmcia_hw_shutdown(struct soc_pcmcia_socket *skt)
+{
+	gpio_free_array(palmld_pcmcia_gpios, ARRAY_SIZE(palmld_pcmcia_gpios));
+}
+
+static void palmld_pcmcia_socket_state(struct soc_pcmcia_socket *skt,
+					struct pcmcia_state *state)
+{
+	state->detect = 1; /* always inserted */
+	state->vs_3v  = 1;
+	state->vs_Xv  = 0;
+}
+
+static int palmld_pcmcia_configure_socket(struct soc_pcmcia_socket *skt,
+					const socket_state_t *state)
+{
+	gpio_set_value(GPIO_NR_PALMLD_PCMCIA_POWER, 1);
+	gpio_set_value(GPIO_NR_PALMLD_PCMCIA_RESET,
+			!!(state->flags & SS_RESET));
+
+	return 0;
+}
+
+static struct pcmcia_low_level palmld_pcmcia_ops = {
+	.owner			= THIS_MODULE,
+
+	.first			= 1,
+	.nr			= 1,
+
+	.hw_init		= palmld_pcmcia_hw_init,
+	.hw_shutdown		= palmld_pcmcia_hw_shutdown,
+
+	.socket_state		= palmld_pcmcia_socket_state,
+	.configure_socket	= palmld_pcmcia_configure_socket,
+};
+
+static struct platform_device *palmld_pcmcia_device;
+
+static int __init palmld_pcmcia_init(void)
+{
+	int ret;
+
+	if (!machine_is_palmld())
+		return -ENODEV;
+
+	palmld_pcmcia_device = platform_device_alloc("pxa2xx-pcmcia", -1);
+	if (!palmld_pcmcia_device)
+		return -ENOMEM;
+
+	ret = platform_device_add_data(palmld_pcmcia_device, &palmld_pcmcia_ops,
+					sizeof(palmld_pcmcia_ops));
+
+	if (!ret)
+		ret = platform_device_add(palmld_pcmcia_device);
+
+	if (ret)
+		platform_device_put(palmld_pcmcia_device);
+
+	return ret;
+}
+
+static void __exit palmld_pcmcia_exit(void)
+{
+	platform_device_unregister(palmld_pcmcia_device);
+}
+
+module_init(palmld_pcmcia_init);
+module_exit(palmld_pcmcia_exit);
+
+MODULE_AUTHOR("Alex Osborne <ato@meshy.org>,"
+	    " Marek Vasut <marek.vasut@gmail.com>");
+MODULE_DESCRIPTION("PCMCIA support for Palm LifeDrive");
+MODULE_ALIAS("platform:pxa2xx-pcmcia");
+MODULE_LICENSE("GPL");
diff --git a/arch/arm/mach-pxa/palmld.c b/arch/arm/mach-pxa/palmld.c
index 5f73716a77f0..32308c63884e 100644
--- a/arch/arm/mach-pxa/palmld.c
+++ b/arch/arm/mach-pxa/palmld.c
@@ -29,8 +29,8 @@
 #include <asm/mach/map.h>
 
 #include "pxa27x.h"
-#include <mach/audio.h>
-#include <mach/palmld.h>
+#include "palmld.h"
+#include <linux/platform_data/asoc-pxa.h>
 #include <linux/platform_data/mmc-pxamci.h>
 #include <linux/platform_data/video-pxafb.h>
 #include <linux/platform_data/irda-pxaficp.h>
@@ -279,9 +279,15 @@ static inline void palmld_leds_init(void) {}
  * HDD
  ******************************************************************************/
 #if defined(CONFIG_PATA_PALMLD) || defined(CONFIG_PATA_PALMLD_MODULE)
+static struct resource palmld_ide_resources[] = {
+	DEFINE_RES_MEM(PALMLD_IDE_PHYS, 0x1000),
+};
+
 static struct platform_device palmld_ide_device = {
-	.name	= "pata_palmld",
-	.id	= -1,
+	.name		= "pata_palmld",
+	.id		= -1,
+	.resource	= palmld_ide_resources,
+	.num_resources	= ARRAY_SIZE(palmld_ide_resources),
 };
 
 static struct gpiod_lookup_table palmld_ide_gpio_table = {
@@ -341,6 +347,14 @@ static struct gpiod_lookup_table palmld_mci_gpio_table = {
 	},
 };
 
+static struct gpiod_lookup_table palmld_wm97xx_touch_gpio_table = {
+	.dev_id = "wm97xx-touch",
+	.table = {
+		GPIO_LOOKUP("gpio-pxa", 27, "touch", GPIO_ACTIVE_HIGH),
+		{ },
+	},
+};
+
 static void __init palmld_init(void)
 {
 	pxa2xx_mfp_config(ARRAY_AND_SIZE(palmld_pin_config));
@@ -349,6 +363,7 @@ static void __init palmld_init(void)
 	pxa_set_stuart_info(NULL);
 
 	palm27x_mmc_init(&palmld_mci_gpio_table);
+	gpiod_add_lookup_table(&palmld_wm97xx_touch_gpio_table);
 	palm27x_pm_init(PALMLD_STR_BASE);
 	palm27x_lcd_init(-1, &palm_320x480_lcd_mode);
 	palm27x_irda_init(GPIO_NR_PALMLD_IR_DISABLE);
diff --git a/arch/arm/mach-pxa/include/mach/palmld.h b/arch/arm/mach-pxa/palmld.h
index 99a6d8b3a1e3..99a6d8b3a1e3 100644
--- a/arch/arm/mach-pxa/include/mach/palmld.h
+++ b/arch/arm/mach-pxa/palmld.h
diff --git a/arch/arm/mach-pxa/palmt5.c b/arch/arm/mach-pxa/palmt5.c
index 7c7cbb4e677e..463b62ec1b01 100644
--- a/arch/arm/mach-pxa/palmt5.c
+++ b/arch/arm/mach-pxa/palmt5.c
@@ -29,7 +29,7 @@
 #include <asm/mach/map.h>
 
 #include "pxa27x.h"
-#include <mach/audio.h>
+#include <linux/platform_data/asoc-pxa.h>
 #include "palmt5.h"
 #include <linux/platform_data/mmc-pxamci.h>
 #include <linux/platform_data/video-pxafb.h>
@@ -190,6 +190,14 @@ static struct gpiod_lookup_table palmt5_mci_gpio_table = {
 	},
 };
 
+static struct gpiod_lookup_table palmt5_wm97xx_touch_gpio_table = {
+	.dev_id = "wm97xx-touch",
+	.table = {
+		GPIO_LOOKUP("gpio-pxa", 27, "touch", GPIO_ACTIVE_HIGH),
+		{ },
+	},
+};
+
 static void __init palmt5_init(void)
 {
 	pxa2xx_mfp_config(ARRAY_AND_SIZE(palmt5_pin_config));
@@ -198,6 +206,7 @@ static void __init palmt5_init(void)
 	pxa_set_stuart_info(NULL);
 
 	palm27x_mmc_init(&palmt5_mci_gpio_table);
+	gpiod_add_lookup_table(&palmt5_wm97xx_touch_gpio_table);
 	palm27x_pm_init(PALMT5_STR_BASE);
 	palm27x_lcd_init(-1, &palm_320x480_lcd_mode);
 	palm27x_udc_init(GPIO_NR_PALMT5_USB_DETECT_N,
diff --git a/arch/arm/mach-pxa/palmt5.h b/arch/arm/mach-pxa/palmt5.h
index 1fb1da7c8da3..cf84aedca717 100644
--- a/arch/arm/mach-pxa/palmt5.h
+++ b/arch/arm/mach-pxa/palmt5.h
@@ -11,7 +11,7 @@
 #ifndef _INCLUDE_PALMT5_H_
 #define _INCLUDE_PALMT5_H_
 
-#include <mach/irqs.h> /* PXA_GPIO_TO_IRQ */
+#include "irqs.h" /* PXA_GPIO_TO_IRQ */
 
 /** HERE ARE GPIOs **/
 
diff --git a/arch/arm/mach-pxa/palmtc-pcmcia.c b/arch/arm/mach-pxa/palmtc-pcmcia.c
new file mode 100644
index 000000000000..8e3f382343fe
--- /dev/null
+++ b/arch/arm/mach-pxa/palmtc-pcmcia.c
@@ -0,0 +1,162 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * linux/drivers/pcmcia/pxa2xx_palmtc.c
+ *
+ * Driver for Palm Tungsten|C PCMCIA
+ *
+ * Copyright (C) 2008 Alex Osborne <ato@meshy.org>
+ * Copyright (C) 2009-2011 Marek Vasut <marek.vasut@gmail.com>
+ */
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/gpio.h>
+#include <linux/delay.h>
+
+#include <asm/mach-types.h>
+#include "palmtc.h"
+#include <pcmcia/soc_common.h>
+
+static struct gpio palmtc_pcmcia_gpios[] = {
+	{ GPIO_NR_PALMTC_PCMCIA_POWER1,	GPIOF_INIT_LOW,	"PCMCIA Power 1" },
+	{ GPIO_NR_PALMTC_PCMCIA_POWER2,	GPIOF_INIT_LOW,	"PCMCIA Power 2" },
+	{ GPIO_NR_PALMTC_PCMCIA_POWER3,	GPIOF_INIT_LOW,	"PCMCIA Power 3" },
+	{ GPIO_NR_PALMTC_PCMCIA_RESET,	GPIOF_INIT_HIGH,"PCMCIA Reset" },
+	{ GPIO_NR_PALMTC_PCMCIA_PWRREADY, GPIOF_IN,	"PCMCIA Power Ready" },
+};
+
+static int palmtc_pcmcia_hw_init(struct soc_pcmcia_socket *skt)
+{
+	int ret;
+
+	ret = gpio_request_array(palmtc_pcmcia_gpios,
+				ARRAY_SIZE(palmtc_pcmcia_gpios));
+
+	skt->stat[SOC_STAT_RDY].gpio = GPIO_NR_PALMTC_PCMCIA_READY;
+	skt->stat[SOC_STAT_RDY].name = "PCMCIA Ready";
+
+	return ret;
+}
+
+static void palmtc_pcmcia_hw_shutdown(struct soc_pcmcia_socket *skt)
+{
+	gpio_free_array(palmtc_pcmcia_gpios, ARRAY_SIZE(palmtc_pcmcia_gpios));
+}
+
+static void palmtc_pcmcia_socket_state(struct soc_pcmcia_socket *skt,
+					struct pcmcia_state *state)
+{
+	state->detect = 1; /* always inserted */
+	state->vs_3v  = 1;
+	state->vs_Xv  = 0;
+}
+
+static int palmtc_wifi_powerdown(void)
+{
+	gpio_set_value(GPIO_NR_PALMTC_PCMCIA_RESET, 1);
+	gpio_set_value(GPIO_NR_PALMTC_PCMCIA_POWER2, 0);
+	mdelay(40);
+	gpio_set_value(GPIO_NR_PALMTC_PCMCIA_POWER1, 0);
+	return 0;
+}
+
+static int palmtc_wifi_powerup(void)
+{
+	int timeout = 50;
+
+	gpio_set_value(GPIO_NR_PALMTC_PCMCIA_POWER3, 1);
+	mdelay(50);
+
+	/* Power up the card, 1.8V first, after a while 3.3V */
+	gpio_set_value(GPIO_NR_PALMTC_PCMCIA_POWER1, 1);
+	mdelay(100);
+	gpio_set_value(GPIO_NR_PALMTC_PCMCIA_POWER2, 1);
+
+	/* Wait till the card is ready */
+	while (!gpio_get_value(GPIO_NR_PALMTC_PCMCIA_PWRREADY) &&
+		timeout) {
+		mdelay(1);
+		timeout--;
+	}
+
+	/* Power down the WiFi in case of error */
+	if (!timeout) {
+		palmtc_wifi_powerdown();
+		return 1;
+	}
+
+	/* Reset the card */
+	gpio_set_value(GPIO_NR_PALMTC_PCMCIA_RESET, 1);
+	mdelay(20);
+	gpio_set_value(GPIO_NR_PALMTC_PCMCIA_RESET, 0);
+	mdelay(25);
+
+	gpio_set_value(GPIO_NR_PALMTC_PCMCIA_POWER3, 0);
+
+	return 0;
+}
+
+static int palmtc_pcmcia_configure_socket(struct soc_pcmcia_socket *skt,
+					const socket_state_t *state)
+{
+	int ret = 1;
+
+	if (state->Vcc == 0)
+		ret = palmtc_wifi_powerdown();
+	else if (state->Vcc == 33)
+		ret = palmtc_wifi_powerup();
+
+	return ret;
+}
+
+static struct pcmcia_low_level palmtc_pcmcia_ops = {
+	.owner			= THIS_MODULE,
+
+	.first			= 0,
+	.nr			= 1,
+
+	.hw_init		= palmtc_pcmcia_hw_init,
+	.hw_shutdown		= palmtc_pcmcia_hw_shutdown,
+
+	.socket_state		= palmtc_pcmcia_socket_state,
+	.configure_socket	= palmtc_pcmcia_configure_socket,
+};
+
+static struct platform_device *palmtc_pcmcia_device;
+
+static int __init palmtc_pcmcia_init(void)
+{
+	int ret;
+
+	if (!machine_is_palmtc())
+		return -ENODEV;
+
+	palmtc_pcmcia_device = platform_device_alloc("pxa2xx-pcmcia", -1);
+	if (!palmtc_pcmcia_device)
+		return -ENOMEM;
+
+	ret = platform_device_add_data(palmtc_pcmcia_device, &palmtc_pcmcia_ops,
+					sizeof(palmtc_pcmcia_ops));
+
+	if (!ret)
+		ret = platform_device_add(palmtc_pcmcia_device);
+
+	if (ret)
+		platform_device_put(palmtc_pcmcia_device);
+
+	return ret;
+}
+
+static void __exit palmtc_pcmcia_exit(void)
+{
+	platform_device_unregister(palmtc_pcmcia_device);
+}
+
+module_init(palmtc_pcmcia_init);
+module_exit(palmtc_pcmcia_exit);
+
+MODULE_AUTHOR("Alex Osborne <ato@meshy.org>,"
+	    " Marek Vasut <marek.vasut@gmail.com>");
+MODULE_DESCRIPTION("PCMCIA support for Palm Tungsten|C");
+MODULE_ALIAS("platform:pxa2xx-pcmcia");
+MODULE_LICENSE("GPL");
diff --git a/arch/arm/mach-pxa/palmtc.c b/arch/arm/mach-pxa/palmtc.c
index 455cb8ccaf26..3054ffa397ad 100644
--- a/arch/arm/mach-pxa/palmtc.c
+++ b/arch/arm/mach-pxa/palmtc.c
@@ -29,8 +29,8 @@
 #include <asm/mach/map.h>
 
 #include "pxa25x.h"
-#include <mach/audio.h>
-#include <mach/palmtc.h>
+#include <linux/platform_data/asoc-pxa.h>
+#include "palmtc.h"
 #include <linux/platform_data/mmc-pxamci.h>
 #include <linux/platform_data/video-pxafb.h>
 #include <linux/platform_data/irda-pxaficp.h>
diff --git a/arch/arm/mach-pxa/include/mach/palmtc.h b/arch/arm/mach-pxa/palmtc.h
index 9257a02c46e5..9257a02c46e5 100644
--- a/arch/arm/mach-pxa/include/mach/palmtc.h
+++ b/arch/arm/mach-pxa/palmtc.h
diff --git a/arch/arm/mach-pxa/palmte2.c b/arch/arm/mach-pxa/palmte2.c
index a2b10db4aacc..fedac670a8af 100644
--- a/arch/arm/mach-pxa/palmte2.c
+++ b/arch/arm/mach-pxa/palmte2.c
@@ -29,7 +29,7 @@
 #include <asm/mach/map.h>
 
 #include "pxa25x.h"
-#include <mach/audio.h>
+#include <linux/platform_data/asoc-pxa.h>
 #include "palmte2.h"
 #include <linux/platform_data/mmc-pxamci.h>
 #include <linux/platform_data/video-pxafb.h>
diff --git a/arch/arm/mach-pxa/palmtreo.c b/arch/arm/mach-pxa/palmtreo.c
index 2bf0f7f3ea24..238a31f32cba 100644
--- a/arch/arm/mach-pxa/palmtreo.c
+++ b/arch/arm/mach-pxa/palmtreo.c
@@ -29,7 +29,7 @@
 
 #include "pxa27x.h"
 #include "pxa27x-udc.h"
-#include <mach/audio.h>
+#include <linux/platform_data/asoc-pxa.h>
 #include "palmtreo.h"
 #include <linux/platform_data/mmc-pxamci.h>
 #include <linux/platform_data/video-pxafb.h>
@@ -37,7 +37,7 @@
 #include <linux/platform_data/keypad-pxa27x.h>
 #include "udc.h"
 #include <linux/platform_data/usb-ohci-pxa27x.h>
-#include <mach/pxa2xx-regs.h>
+#include "pxa2xx-regs.h"
 #include <linux/platform_data/asoc-palm27x.h>
 #include <linux/platform_data/media/camera-pxa.h>
 #include "palm27x.h"
diff --git a/arch/arm/mach-pxa/palmtx-pcmcia.c b/arch/arm/mach-pxa/palmtx-pcmcia.c
new file mode 100644
index 000000000000..8c2aaad93043
--- /dev/null
+++ b/arch/arm/mach-pxa/palmtx-pcmcia.c
@@ -0,0 +1,111 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * linux/drivers/pcmcia/pxa2xx_palmtx.c
+ *
+ * Driver for Palm T|X PCMCIA
+ *
+ * Copyright (C) 2007-2011 Marek Vasut <marek.vasut@gmail.com>
+ */
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/gpio.h>
+
+#include <asm/mach-types.h>
+#include "palmtx.h"
+#include <pcmcia/soc_common.h>
+
+static struct gpio palmtx_pcmcia_gpios[] = {
+	{ GPIO_NR_PALMTX_PCMCIA_POWER1,	GPIOF_INIT_LOW,	"PCMCIA Power 1" },
+	{ GPIO_NR_PALMTX_PCMCIA_POWER2,	GPIOF_INIT_LOW,	"PCMCIA Power 2" },
+	{ GPIO_NR_PALMTX_PCMCIA_RESET,	GPIOF_INIT_HIGH,"PCMCIA Reset" },
+};
+
+static int palmtx_pcmcia_hw_init(struct soc_pcmcia_socket *skt)
+{
+	int ret;
+
+	ret = gpio_request_array(palmtx_pcmcia_gpios,
+				ARRAY_SIZE(palmtx_pcmcia_gpios));
+
+	skt->stat[SOC_STAT_RDY].gpio = GPIO_NR_PALMTX_PCMCIA_READY;
+	skt->stat[SOC_STAT_RDY].name = "PCMCIA Ready";
+
+	return ret;
+}
+
+static void palmtx_pcmcia_hw_shutdown(struct soc_pcmcia_socket *skt)
+{
+	gpio_free_array(palmtx_pcmcia_gpios, ARRAY_SIZE(palmtx_pcmcia_gpios));
+}
+
+static void palmtx_pcmcia_socket_state(struct soc_pcmcia_socket *skt,
+					struct pcmcia_state *state)
+{
+	state->detect = 1; /* always inserted */
+	state->vs_3v  = 1;
+	state->vs_Xv  = 0;
+}
+
+static int
+palmtx_pcmcia_configure_socket(struct soc_pcmcia_socket *skt,
+				const socket_state_t *state)
+{
+	gpio_set_value(GPIO_NR_PALMTX_PCMCIA_POWER1, 1);
+	gpio_set_value(GPIO_NR_PALMTX_PCMCIA_POWER2, 1);
+	gpio_set_value(GPIO_NR_PALMTX_PCMCIA_RESET,
+			!!(state->flags & SS_RESET));
+
+	return 0;
+}
+
+static struct pcmcia_low_level palmtx_pcmcia_ops = {
+	.owner			= THIS_MODULE,
+
+	.first			= 0,
+	.nr			= 1,
+
+	.hw_init		= palmtx_pcmcia_hw_init,
+	.hw_shutdown		= palmtx_pcmcia_hw_shutdown,
+
+	.socket_state		= palmtx_pcmcia_socket_state,
+	.configure_socket	= palmtx_pcmcia_configure_socket,
+};
+
+static struct platform_device *palmtx_pcmcia_device;
+
+static int __init palmtx_pcmcia_init(void)
+{
+	int ret;
+
+	if (!machine_is_palmtx())
+		return -ENODEV;
+
+	palmtx_pcmcia_device = platform_device_alloc("pxa2xx-pcmcia", -1);
+	if (!palmtx_pcmcia_device)
+		return -ENOMEM;
+
+	ret = platform_device_add_data(palmtx_pcmcia_device, &palmtx_pcmcia_ops,
+					sizeof(palmtx_pcmcia_ops));
+
+	if (!ret)
+		ret = platform_device_add(palmtx_pcmcia_device);
+
+	if (ret)
+		platform_device_put(palmtx_pcmcia_device);
+
+	return ret;
+}
+
+static void __exit palmtx_pcmcia_exit(void)
+{
+	platform_device_unregister(palmtx_pcmcia_device);
+}
+
+module_init(palmtx_pcmcia_init);
+module_exit(palmtx_pcmcia_exit);
+
+MODULE_AUTHOR("Marek Vasut <marek.vasut@gmail.com>");
+MODULE_DESCRIPTION("PCMCIA support for Palm T|X");
+MODULE_ALIAS("platform:pxa2xx-pcmcia");
+MODULE_LICENSE("GPL");
diff --git a/arch/arm/mach-pxa/palmtx.c b/arch/arm/mach-pxa/palmtx.c
index 07332c92c9f7..c0d0762540ab 100644
--- a/arch/arm/mach-pxa/palmtx.c
+++ b/arch/arm/mach-pxa/palmtx.c
@@ -32,8 +32,8 @@
 #include <asm/mach/map.h>
 
 #include "pxa27x.h"
-#include <mach/audio.h>
-#include <mach/palmtx.h>
+#include <linux/platform_data/asoc-pxa.h>
+#include "palmtx.h"
 #include <linux/platform_data/mmc-pxamci.h>
 #include <linux/platform_data/video-pxafb.h>
 #include <linux/platform_data/irda-pxaficp.h>
@@ -345,6 +345,14 @@ static struct gpiod_lookup_table palmtx_mci_gpio_table = {
 	},
 };
 
+static struct gpiod_lookup_table palmtx_wm97xx_touch_gpio_table = {
+	.dev_id = "wm97xx-touch",
+	.table = {
+		GPIO_LOOKUP("gpio-pxa", 27, "touch", GPIO_ACTIVE_HIGH),
+		{ },
+	},
+};
+
 static void __init palmtx_init(void)
 {
 	pxa2xx_mfp_config(ARRAY_AND_SIZE(palmtx_pin_config));
@@ -353,6 +361,7 @@ static void __init palmtx_init(void)
 	pxa_set_stuart_info(NULL);
 
 	palm27x_mmc_init(&palmtx_mci_gpio_table);
+	gpiod_add_lookup_table(&palmtx_wm97xx_touch_gpio_table);
 	palm27x_pm_init(PALMTX_STR_BASE);
 	palm27x_lcd_init(-1, &palm_320x480_lcd_mode);
 	palm27x_udc_init(GPIO_NR_PALMTX_USB_DETECT_N,
diff --git a/arch/arm/mach-pxa/include/mach/palmtx.h b/arch/arm/mach-pxa/palmtx.h
index ec88abf0fc6c..ec88abf0fc6c 100644
--- a/arch/arm/mach-pxa/include/mach/palmtx.h
+++ b/arch/arm/mach-pxa/palmtx.h
diff --git a/arch/arm/mach-pxa/palmz72.c b/arch/arm/mach-pxa/palmz72.c
index b4a5fe02a0af..66e8fe6f1661 100644
--- a/arch/arm/mach-pxa/palmz72.c
+++ b/arch/arm/mach-pxa/palmz72.c
@@ -34,7 +34,7 @@
 #include <asm/mach/map.h>
 
 #include "pxa27x.h"
-#include <mach/audio.h>
+#include <linux/platform_data/asoc-pxa.h>
 #include "palmz72.h"
 #include <linux/platform_data/mmc-pxamci.h>
 #include <linux/platform_data/video-pxafb.h>
diff --git a/arch/arm/mach-pxa/pcm027.h b/arch/arm/mach-pxa/pcm027.h
index 0c4ab636ce4e..58ade4ad6ba3 100644
--- a/arch/arm/mach-pxa/pcm027.h
+++ b/arch/arm/mach-pxa/pcm027.h
@@ -10,7 +10,7 @@
  * Definitions of CPU card resources only
  */
 
-#include <mach/irqs.h> /* PXA_GPIO_TO_IRQ */
+#include "irqs.h" /* PXA_GPIO_TO_IRQ */
 
 /* phyCORE-PXA270 (PCM027) Interrupts */
 #define PCM027_IRQ(x)          (IRQ_BOARD_START + (x))
diff --git a/arch/arm/mach-pxa/pcm990-baseboard.c b/arch/arm/mach-pxa/pcm990-baseboard.c
index 8dfcc366d0fe..33a9d2eeca1c 100644
--- a/arch/arm/mach-pxa/pcm990-baseboard.c
+++ b/arch/arm/mach-pxa/pcm990-baseboard.c
@@ -26,7 +26,7 @@
 
 #include <asm/mach/map.h>
 #include "pxa27x.h"
-#include <mach/audio.h>
+#include <linux/platform_data/asoc-pxa.h>
 #include <linux/platform_data/mmc-pxamci.h>
 #include <linux/platform_data/usb-ohci-pxa27x.h>
 #include "pcm990_baseboard.h"
diff --git a/arch/arm/mach-pxa/pcm990_baseboard.h b/arch/arm/mach-pxa/pcm990_baseboard.h
index 5be11d1b7019..18cf71decb03 100644
--- a/arch/arm/mach-pxa/pcm990_baseboard.h
+++ b/arch/arm/mach-pxa/pcm990_baseboard.h
@@ -7,7 +7,7 @@
  */
 
 #include "pcm027.h"
-#include <mach/irqs.h> /* PXA_GPIO_TO_IRQ */
+#include "irqs.h" /* PXA_GPIO_TO_IRQ */
 
 /*
  * definitions relevant only when the PCM-990
diff --git a/arch/arm/mach-pxa/poodle.c b/arch/arm/mach-pxa/poodle.c
index 3a4ecc3c8f8b..7772a39430ed 100644
--- a/arch/arm/mach-pxa/poodle.c
+++ b/arch/arm/mach-pxa/poodle.c
@@ -30,7 +30,6 @@
 #include <linux/mtd/sharpsl.h>
 #include <linux/memblock.h>
 
-#include <mach/hardware.h>
 #include <asm/mach-types.h>
 #include <asm/irq.h>
 #include <asm/setup.h>
@@ -40,11 +39,13 @@
 #include <asm/mach/irq.h>
 
 #include "pxa25x.h"
-#include <linux/platform_data/mmc-pxamci.h>
 #include "udc.h"
+#include "poodle.h"
+
+#include <linux/platform_data/mmc-pxamci.h>
 #include <linux/platform_data/irda-pxaficp.h>
-#include <mach/poodle.h>
 #include <linux/platform_data/video-pxafb.h>
+#include <linux/platform_data/asoc-poodle.h>
 
 #include <asm/hardware/scoop.h>
 #include <asm/hardware/locomo.h>
@@ -156,12 +157,6 @@ static struct scoop_pcmcia_config poodle_pcmcia_config = {
 
 EXPORT_SYMBOL(poodle_scoop_device);
 
-
-static struct platform_device poodle_audio_device = {
-	.name	= "poodle-audio",
-	.id	= -1,
-};
-
 /* LoCoMo device */
 static struct resource locomo_resources[] = {
 	[0] = {
@@ -180,7 +175,7 @@ static struct locomo_platform_data locomo_info = {
 	.irq_base	= IRQ_BOARD_START,
 };
 
-struct platform_device poodle_locomo_device = {
+static struct platform_device poodle_locomo_device = {
 	.name		= "locomo",
 	.id		= 0,
 	.num_resources	= ARRAY_SIZE(locomo_resources),
@@ -190,13 +185,35 @@ struct platform_device poodle_locomo_device = {
 	},
 };
 
-EXPORT_SYMBOL(poodle_locomo_device);
+static struct poodle_audio_platform_data poodle_audio_pdata = {
+	.locomo_dev	= &poodle_locomo_device.dev,
+
+	.gpio_amp_on   	= POODLE_LOCOMO_GPIO_AMP_ON,
+	.gpio_mute_l   	= POODLE_LOCOMO_GPIO_MUTE_L,
+	.gpio_mute_r   	= POODLE_LOCOMO_GPIO_MUTE_R,
+	.gpio_232vcc_on	= POODLE_LOCOMO_GPIO_232VCC_ON,
+	.gpio_jk_b     	= POODLE_LOCOMO_GPIO_JK_B,
+};
+
+static struct platform_device poodle_audio_device = {
+	.name	= "poodle-audio",
+	.id	= -1,
+	.dev.platform_data = &poodle_audio_pdata,
+};
 
 #if defined(CONFIG_SPI_PXA2XX) || defined(CONFIG_SPI_PXA2XX_MODULE)
 static struct pxa2xx_spi_controller poodle_spi_info = {
 	.num_chipselect	= 1,
 };
 
+static struct gpiod_lookup_table poodle_spi_gpio_table = {
+	.dev_id = "pxa2xx-spi.1",
+	.table = {
+		GPIO_LOOKUP_IDX("gpio-pxa", POODLE_GPIO_TP_CS, "cs", 0, GPIO_ACTIVE_LOW),
+		{ },
+	},
+};
+
 static struct ads7846_platform_data poodle_ads7846_info = {
 	.model			= 7846,
 	.vref_delay_usecs	= 100,
@@ -205,23 +222,19 @@ static struct ads7846_platform_data poodle_ads7846_info = {
 	.gpio_pendown		= POODLE_GPIO_TP_INT,
 };
 
-static struct pxa2xx_spi_chip poodle_ads7846_chip = {
-	.gpio_cs		= POODLE_GPIO_TP_CS,
-};
-
 static struct spi_board_info poodle_spi_devices[] = {
 	{
 		.modalias	= "ads7846",
 		.max_speed_hz	= 10000,
 		.bus_num	= 1,
 		.platform_data	= &poodle_ads7846_info,
-		.controller_data= &poodle_ads7846_chip,
 		.irq		= PXA_GPIO_TO_IRQ(POODLE_GPIO_TP_INT),
 	},
 };
 
 static void __init poodle_init_spi(void)
 {
+	gpiod_add_lookup_table(&poodle_spi_gpio_table);
 	pxa2xx_set_spi_info(1, &poodle_spi_info);
 	spi_register_board_info(ARRAY_AND_SIZE(poodle_spi_devices));
 }
diff --git a/arch/arm/mach-pxa/include/mach/poodle.h b/arch/arm/mach-pxa/poodle.h
index b56b19351a03..00798b44f204 100644
--- a/arch/arm/mach-pxa/include/mach/poodle.h
+++ b/arch/arm/mach-pxa/poodle.h
@@ -89,6 +89,4 @@
 
 #define POODLE_NR_IRQS		(IRQ_BOARD_START + 4)	/* 4 for LoCoMo */
 
-extern struct platform_device poodle_locomo_device;
-
 #endif /* __ASM_ARCH_POODLE_H  */
diff --git a/arch/arm/mach-pxa/pxa-dt.c b/arch/arm/mach-pxa/pxa-dt.c
index d32d5c8e966f..5e5d543fdf46 100644
--- a/arch/arm/mach-pxa/pxa-dt.c
+++ b/arch/arm/mach-pxa/pxa-dt.c
@@ -11,7 +11,7 @@
 #include <linux/of_platform.h>
 #include <asm/mach/arch.h>
 #include <asm/mach/time.h>
-#include <mach/irqs.h>
+#include "irqs.h"
 
 #include "generic.h"
 
diff --git a/arch/arm/mach-pxa/pxa-regs.h b/arch/arm/mach-pxa/pxa-regs.h
new file mode 100644
index 000000000000..ba5120c06b8a
--- /dev/null
+++ b/arch/arm/mach-pxa/pxa-regs.h
@@ -0,0 +1,52 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ *  Author:	Nicolas Pitre
+ *  Created:	Jun 15, 2001
+ *  Copyright:	MontaVista Software Inc.
+ */
+#ifndef __ASM_MACH_PXA_REGS_H
+#define __ASM_MACH_PXA_REGS_H
+
+/*
+ * Workarounds for at least 2 errata so far require this.
+ * The mapping is set in mach-pxa/generic.c.
+ */
+#define UNCACHED_PHYS_0		0xfe000000
+#define UNCACHED_PHYS_0_SIZE	0x00100000
+
+/*
+ * Intel PXA2xx internal register mapping:
+ *
+ * 0x40000000 - 0x41ffffff <--> 0xf2000000 - 0xf3ffffff
+ * 0x44000000 - 0x45ffffff <--> 0xf4000000 - 0xf5ffffff
+ * 0x48000000 - 0x49ffffff <--> 0xf6000000 - 0xf7ffffff
+ * 0x4c000000 - 0x4dffffff <--> 0xf8000000 - 0xf9ffffff
+ * 0x50000000 - 0x51ffffff <--> 0xfa000000 - 0xfbffffff
+ * 0x54000000 - 0x55ffffff <--> 0xfc000000 - 0xfdffffff
+ * 0x58000000 - 0x59ffffff <--> 0xfe000000 - 0xffffffff
+ *
+ * Note that not all PXA2xx chips implement all those addresses, and the
+ * kernel only maps the minimum needed range of this mapping.
+ */
+#define io_v2p(x) (0x3c000000 + ((x) & 0x01ffffff) + (((x) & 0x0e000000) << 1))
+#define io_p2v(x) IOMEM(0xf2000000 + ((x) & 0x01ffffff) + (((x) & 0x1c000000) >> 1))
+
+#ifndef __ASSEMBLY__
+# define __REG(x)	(*((volatile u32 __iomem *)io_p2v(x)))
+
+/* With indexed regs we don't want to feed the index through io_p2v()
+   especially if it is a variable, otherwise horrible code will result. */
+# define __REG2(x,y)	\
+	(*(volatile u32 __iomem*)((u32)&__REG(x) + (y)))
+
+# define __PREG(x)	(io_v2p((u32)&(x)))
+
+#else
+
+# define __REG(x)	io_p2v(x)
+# define __PREG(x)	io_v2p(x)
+
+#endif
+
+
+#endif
diff --git a/arch/arm/mach-pxa/pxa25x.c b/arch/arm/mach-pxa/pxa25x.c
index 678641ab46e5..6b34d7c169ea 100644
--- a/arch/arm/mach-pxa/pxa25x.c
+++ b/arch/arm/mach-pxa/pxa25x.c
@@ -26,16 +26,16 @@
 #include <linux/irq.h>
 #include <linux/irqchip.h>
 #include <linux/platform_data/mmp_dma.h>
+#include <linux/soc/pxa/cpu.h>
 
 #include <asm/mach/map.h>
 #include <asm/suspend.h>
-#include <mach/hardware.h>
-#include <mach/irqs.h>
+#include "irqs.h"
 #include "pxa25x.h"
-#include <mach/reset.h>
+#include "reset.h"
 #include "pm.h"
-#include <mach/dma.h>
-#include <mach/smemc.h>
+#include "addr-map.h"
+#include "smemc.h"
 
 #include "generic.h"
 #include "devices.h"
@@ -240,7 +240,7 @@ static int __init pxa25x_init(void)
 
 	if (cpu_is_pxa25x()) {
 
-		reset_status = RCSR;
+		pxa_register_wdt(RCSR);
 
 		pxa25x_init_pm();
 
diff --git a/arch/arm/mach-pxa/pxa25x.h b/arch/arm/mach-pxa/pxa25x.h
index b58d0fbdb4db..eaaa87666324 100644
--- a/arch/arm/mach-pxa/pxa25x.h
+++ b/arch/arm/mach-pxa/pxa25x.h
@@ -2,9 +2,9 @@
 #ifndef __MACH_PXA25x_H
 #define __MACH_PXA25x_H
 
-#include <mach/hardware.h>
-#include <mach/pxa2xx-regs.h>
+#include "addr-map.h"
+#include "pxa2xx-regs.h"
 #include "mfp-pxa25x.h"
-#include <mach/irqs.h>
+#include "irqs.h"
 
 #endif /* __MACH_PXA25x_H */
diff --git a/arch/arm/mach-pxa/pxa27x-udc.h b/arch/arm/mach-pxa/pxa27x-udc.h
index faf73804697f..2d3df3b1cb68 100644
--- a/arch/arm/mach-pxa/pxa27x-udc.h
+++ b/arch/arm/mach-pxa/pxa27x-udc.h
@@ -2,6 +2,8 @@
 #ifndef _ASM_ARCH_PXA27X_UDC_H
 #define _ASM_ARCH_PXA27X_UDC_H
 
+#include "pxa-regs.h"
+
 #ifdef _ASM_ARCH_PXA25X_UDC_H
 #error You cannot include both PXA25x and PXA27x UDC support
 #endif
diff --git a/arch/arm/mach-pxa/pxa27x.c b/arch/arm/mach-pxa/pxa27x.c
index f0ba7ed24cb6..afbf6ace954f 100644
--- a/arch/arm/mach-pxa/pxa27x.c
+++ b/arch/arm/mach-pxa/pxa27x.c
@@ -23,18 +23,18 @@
 #include <linux/irq.h>
 #include <linux/platform_data/i2c-pxa.h>
 #include <linux/platform_data/mmp_dma.h>
+#include <linux/soc/pxa/cpu.h>
 
 #include <asm/mach/map.h>
-#include <mach/hardware.h>
 #include <asm/irq.h>
 #include <asm/suspend.h>
-#include <mach/irqs.h>
+#include "irqs.h"
 #include "pxa27x.h"
-#include <mach/reset.h>
+#include "reset.h"
 #include <linux/platform_data/usb-ohci-pxa27x.h>
 #include "pm.h"
-#include <mach/dma.h>
-#include <mach/smemc.h>
+#include "addr-map.h"
+#include "smemc.h"
 
 #include "generic.h"
 #include "devices.h"
@@ -337,7 +337,7 @@ static int __init pxa27x_init(void)
 
 	if (cpu_is_pxa27x()) {
 
-		reset_status = RCSR;
+		pxa_register_wdt(RCSR);
 
 		pxa27x_init_pm();
 
diff --git a/arch/arm/mach-pxa/pxa27x.h b/arch/arm/mach-pxa/pxa27x.h
index abdc02fb4f03..ede96f3f7214 100644
--- a/arch/arm/mach-pxa/pxa27x.h
+++ b/arch/arm/mach-pxa/pxa27x.h
@@ -3,10 +3,10 @@
 #define __MACH_PXA27x_H
 
 #include <linux/suspend.h>
-#include <mach/hardware.h>
-#include <mach/pxa2xx-regs.h>
+#include "addr-map.h"
+#include "pxa2xx-regs.h"
 #include "mfp-pxa27x.h"
-#include <mach/irqs.h>
+#include "irqs.h"
 
 #define ARB_CNTRL	__REG(0x48000048)  /* Arbiter Control Register */
 
diff --git a/arch/arm/mach-pxa/include/mach/pxa2xx-regs.h b/arch/arm/mach-pxa/pxa2xx-regs.h
index fa121e135915..0b7eaf6b5813 100644
--- a/arch/arm/mach-pxa/include/mach/pxa2xx-regs.h
+++ b/arch/arm/mach-pxa/pxa2xx-regs.h
@@ -11,7 +11,7 @@
 #ifndef __PXA2XX_REGS_H
 #define __PXA2XX_REGS_H
 
-#include <mach/hardware.h>
+#include "pxa-regs.h"
 
 /*
  * Power Manager
@@ -136,51 +136,6 @@
 #define CKEN		io_p2v(0x41300004)  /* Clock Enable Register */
 #define OSCC		io_p2v(0x41300008)  /* Oscillator Configuration Register */
 
-#define CCCR_N_MASK	0x0380	/* Run Mode Frequency to Turbo Mode Frequency Multiplier */
-#define CCCR_M_MASK	0x0060	/* Memory Frequency to Run Mode Frequency Multiplier */
-#define CCCR_L_MASK	0x001f	/* Crystal Frequency to Memory Frequency Multiplier */
-
-#define CCCR_CPDIS_BIT	(31)
-#define CCCR_PPDIS_BIT	(30)
-#define CCCR_LCD_26_BIT	(27)
-#define CCCR_A_BIT	(25)
-
-#define CCSR_N2_MASK	CCCR_N_MASK
-#define CCSR_M_MASK	CCCR_M_MASK
-#define CCSR_L_MASK	CCCR_L_MASK
-#define CCSR_N2_SHIFT	7
-
-#define CKEN_AC97CONF   (31)    /* AC97 Controller Configuration */
-#define CKEN_CAMERA	(24)	/* Camera Interface Clock Enable */
-#define CKEN_SSP1	(23)	/* SSP1 Unit Clock Enable */
-#define CKEN_MEMC	(22)	/* Memory Controller Clock Enable */
-#define CKEN_MEMSTK	(21)	/* Memory Stick Host Controller */
-#define CKEN_IM		(20)	/* Internal Memory Clock Enable */
-#define CKEN_KEYPAD	(19)	/* Keypad Interface Clock Enable */
-#define CKEN_USIM	(18)	/* USIM Unit Clock Enable */
-#define CKEN_MSL	(17)	/* MSL Unit Clock Enable */
-#define CKEN_LCD	(16)	/* LCD Unit Clock Enable */
-#define CKEN_PWRI2C	(15)	/* PWR I2C Unit Clock Enable */
-#define CKEN_I2C	(14)	/* I2C Unit Clock Enable */
-#define CKEN_FICP	(13)	/* FICP Unit Clock Enable */
-#define CKEN_MMC	(12)	/* MMC Unit Clock Enable */
-#define CKEN_USB	(11)	/* USB Unit Clock Enable */
-#define CKEN_ASSP	(10)	/* ASSP (SSP3) Clock Enable */
-#define CKEN_USBHOST	(10)	/* USB Host Unit Clock Enable */
-#define CKEN_OSTIMER	(9)	/* OS Timer Unit Clock Enable */
-#define CKEN_NSSP	(9)	/* NSSP (SSP2) Clock Enable */
-#define CKEN_I2S	(8)	/* I2S Unit Clock Enable */
-#define CKEN_BTUART	(7)	/* BTUART Unit Clock Enable */
-#define CKEN_FFUART	(6)	/* FFUART Unit Clock Enable */
-#define CKEN_STUART	(5)	/* STUART Unit Clock Enable */
-#define CKEN_HWUART	(4)	/* HWUART Unit Clock Enable */
-#define CKEN_SSP3	(4)	/* SSP3 Unit Clock Enable */
-#define CKEN_SSP	(3)	/* SSP Unit Clock Enable */
-#define CKEN_SSP2	(3)	/* SSP2 Unit Clock Enable */
-#define CKEN_AC97	(2)	/* AC97 Unit Clock Enable */
-#define CKEN_PWM1	(1)	/* PWM1 Clock Enable */
-#define CKEN_PWM0	(0)	/* PWM0 Clock Enable */
-
 #define OSCC_OON	(1 << 1)	/* 32.768kHz OON (write-once only bit) */
 #define OSCC_OOK	(1 << 0)	/* 32.768kHz OOK (read-only bit) */
 
diff --git a/arch/arm/mach-pxa/pxa2xx.c b/arch/arm/mach-pxa/pxa2xx.c
index 2d26cd2afbf3..4aafd692c1e8 100644
--- a/arch/arm/mach-pxa/pxa2xx.c
+++ b/arch/arm/mach-pxa/pxa2xx.c
@@ -12,10 +12,12 @@
 #include <linux/device.h>
 #include <linux/io.h>
 
-#include <mach/hardware.h>
-#include <mach/pxa2xx-regs.h>
+#include "pxa2xx-regs.h"
 #include "mfp-pxa25x.h"
-#include <mach/reset.h>
+#include "generic.h"
+#include "reset.h"
+#include "smemc.h"
+#include <linux/soc/pxa/smemc.h>
 #include <linux/platform_data/irda-pxaficp.h>
 
 void pxa2xx_clear_reset_status(unsigned int mask)
@@ -51,3 +53,27 @@ void pxa2xx_transceiver_mode(struct device *dev, int mode)
 		BUG();
 }
 EXPORT_SYMBOL_GPL(pxa2xx_transceiver_mode);
+
+#define MDCNFG_DRAC2(mdcnfg)	(((mdcnfg) >> 21) & 0x3)
+#define MDCNFG_DRAC0(mdcnfg)	(((mdcnfg) >> 5) & 0x3)
+
+int pxa2xx_smemc_get_sdram_rows(void)
+{
+	static int sdram_rows;
+	unsigned int drac2 = 0, drac0 = 0;
+	u32 mdcnfg;
+
+	if (sdram_rows)
+		return sdram_rows;
+
+	mdcnfg = readl_relaxed(MDCNFG);
+
+	if (mdcnfg & (MDCNFG_DE2 | MDCNFG_DE3))
+		drac2 = MDCNFG_DRAC2(mdcnfg);
+
+	if (mdcnfg & (MDCNFG_DE0 | MDCNFG_DE1))
+		drac0 = MDCNFG_DRAC0(mdcnfg);
+
+	sdram_rows = 1 << (11 + max(drac0, drac2));
+	return sdram_rows;
+}
diff --git a/arch/arm/mach-pxa/pxa300.c b/arch/arm/mach-pxa/pxa300.c
index 7f2f5a6a2263..f77ec118d5b9 100644
--- a/arch/arm/mach-pxa/pxa300.c
+++ b/arch/arm/mach-pxa/pxa300.c
@@ -14,6 +14,7 @@
 #include <linux/kernel.h>
 #include <linux/platform_device.h>
 #include <linux/io.h>
+#include <linux/soc/pxa/cpu.h>
 
 #include "pxa300.h"
 
diff --git a/arch/arm/mach-pxa/pxa320.c b/arch/arm/mach-pxa/pxa320.c
index 78abcc741df7..e372e6c118de 100644
--- a/arch/arm/mach-pxa/pxa320.c
+++ b/arch/arm/mach-pxa/pxa320.c
@@ -14,6 +14,7 @@
 #include <linux/kernel.h>
 #include <linux/platform_device.h>
 #include <linux/io.h>
+#include <linux/soc/pxa/cpu.h>
 
 #include "pxa320.h"
 
diff --git a/arch/arm/mach-pxa/pxa3xx-regs.h b/arch/arm/mach-pxa/pxa3xx-regs.h
new file mode 100644
index 000000000000..4b11cf81a9e6
--- /dev/null
+++ b/arch/arm/mach-pxa/pxa3xx-regs.h
@@ -0,0 +1,134 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * arch/arm/mach-pxa/include/mach/pxa3xx-regs.h
+ *
+ * PXA3xx specific register definitions
+ *
+ * Copyright (C) 2007 Marvell International Ltd.
+ */
+
+#ifndef __ASM_ARCH_PXA3XX_REGS_H
+#define __ASM_ARCH_PXA3XX_REGS_H
+
+#include "pxa-regs.h"
+
+/*
+ * Oscillator Configuration Register (OSCC)
+ */
+#define OSCC           io_p2v(0x41350000)  /* Oscillator Configuration Register */
+
+#define OSCC_PEN       (1 << 11)       /* 13MHz POUT */
+
+
+/*
+ * Service Power Management Unit (MPMU)
+ */
+#define PMCR		__REG(0x40F50000)	/* Power Manager Control Register */
+#define PSR		__REG(0x40F50004)	/* Power Manager S2 Status Register */
+#define PSPR		__REG(0x40F50008)	/* Power Manager Scratch Pad Register */
+#define PCFR		__REG(0x40F5000C)	/* Power Manager General Configuration Register */
+#define PWER		__REG(0x40F50010)	/* Power Manager Wake-up Enable Register */
+#define PWSR		__REG(0x40F50014)	/* Power Manager Wake-up Status Register */
+#define PECR		__REG(0x40F50018)	/* Power Manager EXT_WAKEUP[1:0] Control Register */
+#define DCDCSR		__REG(0x40F50080)	/* DC-DC Controller Status Register */
+#define PVCR		__REG(0x40F50100)	/* Power Manager Voltage Change Control Register */
+#define PCMD(x)		__REG(0x40F50110 + ((x) << 2))
+
+/*
+ * Slave Power Management Unit
+ */
+#define ASCR		__REG(0x40f40000)	/* Application Subsystem Power Status/Configuration */
+#define ARSR		__REG(0x40f40004)	/* Application Subsystem Reset Status */
+#define AD3ER		__REG(0x40f40008)	/* Application Subsystem Wake-Up from D3 Enable */
+#define AD3SR		__REG(0x40f4000c)	/* Application Subsystem Wake-Up from D3 Status */
+#define AD2D0ER		__REG(0x40f40010)	/* Application Subsystem Wake-Up from D2 to D0 Enable */
+#define AD2D0SR		__REG(0x40f40014)	/* Application Subsystem Wake-Up from D2 to D0 Status */
+#define AD2D1ER		__REG(0x40f40018)	/* Application Subsystem Wake-Up from D2 to D1 Enable */
+#define AD2D1SR		__REG(0x40f4001c)	/* Application Subsystem Wake-Up from D2 to D1 Status */
+#define AD1D0ER		__REG(0x40f40020)	/* Application Subsystem Wake-Up from D1 to D0 Enable */
+#define AD1D0SR		__REG(0x40f40024)	/* Application Subsystem Wake-Up from D1 to D0 Status */
+#define AGENP		__REG(0x40f4002c)	/* Application Subsystem General Purpose */
+#define AD3R		__REG(0x40f40030)	/* Application Subsystem D3 Configuration */
+#define AD2R		__REG(0x40f40034)	/* Application Subsystem D2 Configuration */
+#define AD1R		__REG(0x40f40038)	/* Application Subsystem D1 Configuration */
+
+/*
+ * Application Subsystem Configuration bits.
+ */
+#define ASCR_RDH		(1 << 31)
+#define ASCR_D1S		(1 << 2)
+#define ASCR_D2S		(1 << 1)
+#define ASCR_D3S		(1 << 0)
+
+/*
+ * Application Reset Status bits.
+ */
+#define ARSR_GPR		(1 << 3)
+#define ARSR_LPMR		(1 << 2)
+#define ARSR_WDT		(1 << 1)
+#define ARSR_HWR		(1 << 0)
+
+/*
+ * Application Subsystem Wake-Up bits.
+ */
+#define ADXER_WRTC		(1 << 31)	/* RTC */
+#define ADXER_WOST		(1 << 30)	/* OS Timer */
+#define ADXER_WTSI		(1 << 29)	/* Touchscreen */
+#define ADXER_WUSBH		(1 << 28)	/* USB host */
+#define ADXER_WUSB2		(1 << 26)	/* USB client 2.0 */
+#define ADXER_WMSL0		(1 << 24)	/* MSL port 0*/
+#define ADXER_WDMUX3		(1 << 23)	/* USB EDMUX3 */
+#define ADXER_WDMUX2		(1 << 22)	/* USB EDMUX2 */
+#define ADXER_WKP		(1 << 21)	/* Keypad */
+#define ADXER_WUSIM1		(1 << 20)	/* USIM Port 1 */
+#define ADXER_WUSIM0		(1 << 19)	/* USIM Port 0 */
+#define ADXER_WOTG		(1 << 16)	/* USBOTG input */
+#define ADXER_MFP_WFLASH	(1 << 15)	/* MFP: Data flash busy */
+#define ADXER_MFP_GEN12		(1 << 14)	/* MFP: MMC3/GPIO/OST inputs */
+#define ADXER_MFP_WMMC2		(1 << 13)	/* MFP: MMC2 */
+#define ADXER_MFP_WMMC1		(1 << 12)	/* MFP: MMC1 */
+#define ADXER_MFP_WI2C		(1 << 11)	/* MFP: I2C */
+#define ADXER_MFP_WSSP4		(1 << 10)	/* MFP: SSP4 */
+#define ADXER_MFP_WSSP3		(1 << 9)	/* MFP: SSP3 */
+#define ADXER_MFP_WMAXTRIX	(1 << 8)	/* MFP: matrix keypad */
+#define ADXER_MFP_WUART3	(1 << 7)	/* MFP: UART3 */
+#define ADXER_MFP_WUART2	(1 << 6)	/* MFP: UART2 */
+#define ADXER_MFP_WUART1	(1 << 5)	/* MFP: UART1 */
+#define ADXER_MFP_WSSP2		(1 << 4)	/* MFP: SSP2 */
+#define ADXER_MFP_WSSP1		(1 << 3)	/* MFP: SSP1 */
+#define ADXER_MFP_WAC97		(1 << 2)	/* MFP: AC97 */
+#define ADXER_WEXTWAKE1		(1 << 1)	/* External Wake 1 */
+#define ADXER_WEXTWAKE0		(1 << 0)	/* External Wake 0 */
+
+/*
+ * AD3R/AD2R/AD1R bits.  R2-R5 are only defined for PXA320.
+ */
+#define ADXR_L2			(1 << 8)
+#define ADXR_R5			(1 << 5)
+#define ADXR_R4			(1 << 4)
+#define ADXR_R3			(1 << 3)
+#define ADXR_R2			(1 << 2)
+#define ADXR_R1			(1 << 1)
+#define ADXR_R0			(1 << 0)
+
+/*
+ * Values for PWRMODE CP15 register
+ */
+#define PXA3xx_PM_S3D4C4	0x07	/* aka deep sleep */
+#define PXA3xx_PM_S2D3C4	0x06	/* aka sleep */
+#define PXA3xx_PM_S0D2C2	0x03	/* aka standby */
+#define PXA3xx_PM_S0D1C2	0x02	/* aka LCD refresh */
+#define PXA3xx_PM_S0D0C1	0x01
+
+/*
+ * Application Subsystem Clock
+ */
+#define ACCR		__REG(0x41340000)	/* Application Subsystem Clock Configuration Register */
+#define ACSR		__REG(0x41340004)	/* Application Subsystem Clock Status Register */
+#define AICSR		__REG(0x41340008)	/* Application Subsystem Interrupt Control/Status Register */
+#define CKENA		__REG(0x4134000C)	/* A Clock Enable Register */
+#define CKENB		__REG(0x41340010)	/* B Clock Enable Register */
+#define CKENC		__REG(0x41340024)	/* C Clock Enable Register */
+#define AC97_DIV	__REG(0x41340014)	/* AC97 clock divisor value register */
+
+#endif /* __ASM_ARCH_PXA3XX_REGS_H */
diff --git a/arch/arm/mach-pxa/pxa3xx-ulpi.c b/arch/arm/mach-pxa/pxa3xx-ulpi.c
index 4bd7da1f8657..c29a7f0fa1b0 100644
--- a/arch/arm/mach-pxa/pxa3xx-ulpi.c
+++ b/arch/arm/mach-pxa/pxa3xx-ulpi.c
@@ -21,8 +21,8 @@
 #include <linux/clk.h>
 #include <linux/usb.h>
 #include <linux/usb/otg.h>
+#include <linux/soc/pxa/cpu.h>
 
-#include <mach/hardware.h>
 #include "regs-u2d.h"
 #include <linux/platform_data/usb-pxa3xx-ulpi.h>
 
diff --git a/arch/arm/mach-pxa/pxa3xx.c b/arch/arm/mach-pxa/pxa3xx.c
index 560160682df6..979642aa7ffe 100644
--- a/arch/arm/mach-pxa/pxa3xx.c
+++ b/arch/arm/mach-pxa/pxa3xx.c
@@ -24,17 +24,18 @@
 #include <linux/syscore_ops.h>
 #include <linux/platform_data/i2c-pxa.h>
 #include <linux/platform_data/mmp_dma.h>
+#include <linux/soc/pxa/cpu.h>
+#include <linux/clk/pxa.h>
 
 #include <asm/mach/map.h>
 #include <asm/suspend.h>
-#include <mach/hardware.h>
-#include <mach/pxa3xx-regs.h>
-#include <mach/reset.h>
+#include "pxa3xx-regs.h"
+#include "reset.h"
 #include <linux/platform_data/usb-ohci-pxa27x.h>
 #include "pm.h"
-#include <mach/dma.h>
-#include <mach/smemc.h>
-#include <mach/irqs.h>
+#include "addr-map.h"
+#include "smemc.h"
+#include "irqs.h"
 
 #include "generic.h"
 #include "devices.h"
@@ -51,6 +52,10 @@ extern void __init pxa_dt_irq_init(int (*fn)(struct irq_data *, unsigned int));
 #define NDCR_ND_ARB_EN		(1 << 12)
 #define NDCR_ND_ARB_CNTL	(1 << 19)
 
+#define CKEN_BOOT  		11      /* < Boot rom clock enable */
+#define CKEN_TPM   		19      /* < TPM clock enable */
+#define CKEN_HSIO2 		41      /* < HSIO2 clock enable */
+
 #ifdef CONFIG_PM
 
 #define ISRAM_START	0x5c000000
@@ -463,7 +468,7 @@ static int __init pxa3xx_init(void)
 
 	if (cpu_is_pxa3xx()) {
 
-		reset_status = ARSR;
+		pxa_register_wdt(ARSR);
 
 		/*
 		 * clear RDH bit every time after reset
diff --git a/arch/arm/mach-pxa/pxa3xx.h b/arch/arm/mach-pxa/pxa3xx.h
index 6d4502aa9d06..81825f7ad258 100644
--- a/arch/arm/mach-pxa/pxa3xx.h
+++ b/arch/arm/mach-pxa/pxa3xx.h
@@ -2,8 +2,8 @@
 #ifndef __MACH_PXA3XX_H	
 #define __MACH_PXA3XX_H
 
-#include <mach/hardware.h>
-#include <mach/pxa3xx-regs.h>
-#include <mach/irqs.h>
+#include "addr-map.h"
+#include "pxa3xx-regs.h"
+#include "irqs.h"
 
 #endif /* __MACH_PXA3XX_H */
diff --git a/arch/arm/mach-pxa/pxa930.c b/arch/arm/mach-pxa/pxa930.c
index bf91de4267e5..b9021a40cbd1 100644
--- a/arch/arm/mach-pxa/pxa930.c
+++ b/arch/arm/mach-pxa/pxa930.c
@@ -13,6 +13,7 @@
 #include <linux/irq.h>
 #include <linux/gpio-pxa.h>
 #include <linux/platform_device.h>
+#include <linux/soc/pxa/cpu.h>
 
 #include "pxa930.h"
 
diff --git a/arch/arm/mach-pxa/include/mach/regs-ost.h b/arch/arm/mach-pxa/regs-ost.h
index deb564ed8ee7..c8001cfc8d6b 100644
--- a/arch/arm/mach-pxa/include/mach/regs-ost.h
+++ b/arch/arm/mach-pxa/regs-ost.h
@@ -2,11 +2,13 @@
 #ifndef __ASM_MACH_REGS_OST_H
 #define __ASM_MACH_REGS_OST_H
 
-#include <mach/hardware.h>
+#include "pxa-regs.h"
 
 /*
  * OS Timer & Match Registers
  */
+#define OST_PHYS	0x40A00000
+#define OST_LEN		0x00000020
 
 #define OSMR0		io_p2v(0x40A00000)  /* */
 #define OSMR1		io_p2v(0x40A00004)  /* */
diff --git a/arch/arm/mach-pxa/regs-rtc.h b/arch/arm/mach-pxa/regs-rtc.h
index b1f9ff14e335..96255a0f595e 100644
--- a/arch/arm/mach-pxa/regs-rtc.h
+++ b/arch/arm/mach-pxa/regs-rtc.h
@@ -2,7 +2,7 @@
 #ifndef __ASM_MACH_REGS_RTC_H
 #define __ASM_MACH_REGS_RTC_H
 
-#include <mach/hardware.h>
+#include "pxa-regs.h"
 
 /*
  * Real Time Clock
diff --git a/arch/arm/mach-pxa/regs-u2d.h b/arch/arm/mach-pxa/regs-u2d.h
index fe4c80ad87ec..ab517ba62c9a 100644
--- a/arch/arm/mach-pxa/regs-u2d.h
+++ b/arch/arm/mach-pxa/regs-u2d.h
@@ -2,8 +2,6 @@
 #ifndef __ASM_ARCH_PXA3xx_U2D_H
 #define __ASM_ARCH_PXA3xx_U2D_H
 
-#include <mach/bitfield.h>
-
 /*
  * USB2 device controller registers and bits definitions
  */
diff --git a/arch/arm/mach-pxa/include/mach/regs-uart.h b/arch/arm/mach-pxa/regs-uart.h
index 9a168f83afeb..490e9ca16297 100644
--- a/arch/arm/mach-pxa/include/mach/regs-uart.h
+++ b/arch/arm/mach-pxa/regs-uart.h
@@ -2,6 +2,8 @@
 #ifndef __ASM_ARCH_REGS_UART_H
 #define __ASM_ARCH_REGS_UART_H
 
+#include "pxa-regs.h"
+
 /*
  * UARTs
  */
diff --git a/arch/arm/mach-pxa/reset.c b/arch/arm/mach-pxa/reset.c
index af78405aa4e9..f0be90573ad3 100644
--- a/arch/arm/mach-pxa/reset.c
+++ b/arch/arm/mach-pxa/reset.c
@@ -7,12 +7,9 @@
 #include <asm/proc-fns.h>
 #include <asm/system_misc.h>
 
-#include <mach/regs-ost.h>
-#include <mach/reset.h>
-#include <mach/smemc.h>
-
-unsigned int reset_status;
-EXPORT_SYMBOL(reset_status);
+#include "regs-ost.h"
+#include "reset.h"
+#include "smemc.h"
 
 static void do_hw_reset(void);
 
diff --git a/arch/arm/mach-pxa/reset.h b/arch/arm/mach-pxa/reset.h
new file mode 100644
index 000000000000..963dd190bc13
--- /dev/null
+++ b/arch/arm/mach-pxa/reset.h
@@ -0,0 +1,22 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __ASM_ARCH_RESET_H
+#define __ASM_ARCH_RESET_H
+
+#define RESET_STATUS_HARDWARE	(1 << 0)	/* Hardware Reset */
+#define RESET_STATUS_WATCHDOG	(1 << 1)	/* Watchdog Reset */
+#define RESET_STATUS_LOWPOWER	(1 << 2)	/* Low Power/Sleep Exit */
+#define RESET_STATUS_GPIO	(1 << 3)	/* GPIO Reset */
+#define RESET_STATUS_ALL	(0xf)
+
+extern void clear_reset_status(unsigned int mask);
+extern void pxa_register_wdt(unsigned int reset_status);
+
+/**
+ * init_gpio_reset() - register GPIO as reset generator
+ * @gpio: gpio nr
+ * @output: set gpio as output instead of input during normal work
+ * @level: output level
+ */
+extern int init_gpio_reset(int gpio, int output, int level);
+
+#endif /* __ASM_ARCH_RESET_H */
diff --git a/arch/arm/mach-pxa/sharpsl_pm.c b/arch/arm/mach-pxa/sharpsl_pm.c
index 83cfbb882a2d..a829baf8d922 100644
--- a/arch/arm/mach-pxa/sharpsl_pm.c
+++ b/arch/arm/mach-pxa/sharpsl_pm.c
@@ -24,7 +24,7 @@
 
 #include <asm/mach-types.h>
 #include "pm.h"
-#include <mach/pxa2xx-regs.h>
+#include "pxa2xx-regs.h"
 #include "regs-rtc.h"
 #include "sharpsl_pm.h"
 
diff --git a/arch/arm/mach-pxa/sleep.S b/arch/arm/mach-pxa/sleep.S
index 6c5b3ffd2cd3..d58cf52e3848 100644
--- a/arch/arm/mach-pxa/sleep.S
+++ b/arch/arm/mach-pxa/sleep.S
@@ -13,13 +13,14 @@
 
 #include <linux/linkage.h>
 #include <asm/assembler.h>
-#include <mach/hardware.h>
-#include <mach/smemc.h>
-#include <mach/pxa2xx-regs.h>
+#include "smemc.h"
+#include "pxa2xx-regs.h"
 
 #define MDREFR_KDIV	0x200a4000	// all banks
 #define CCCR_SLEEP	0x00000107	// L=7 2N=2 A=0 PPDIS=0 CPDIS=0
-
+#define CCCR_N_MASK     0x00000380
+#define CCCR_M_MASK     0x00000060
+#define CCCR_L_MASK     0x0000001f
 		.text
 
 #ifdef CONFIG_PXA3xx
diff --git a/arch/arm/mach-pxa/smemc.c b/arch/arm/mach-pxa/smemc.c
index 32e82cc92ea5..2d2a321d82f8 100644
--- a/arch/arm/mach-pxa/smemc.c
+++ b/arch/arm/mach-pxa/smemc.c
@@ -8,9 +8,10 @@
 #include <linux/init.h>
 #include <linux/io.h>
 #include <linux/syscore_ops.h>
+#include <linux/soc/pxa/cpu.h>
 
-#include <mach/hardware.h>
-#include <mach/smemc.h>
+#include "smemc.h"
+#include <linux/soc/pxa/smemc.h>
 
 #ifdef CONFIG_PM
 static unsigned long msc[2];
@@ -70,3 +71,11 @@ static int __init smemc_init(void)
 }
 subsys_initcall(smemc_init);
 #endif
+
+static const unsigned int df_clkdiv[4] = { 1, 2, 4, 1 };
+unsigned int pxa3xx_smemc_get_memclkdiv(void)
+{
+	unsigned long memclkcfg = __raw_readl(MEMCLKCFG);
+
+	return	df_clkdiv[(memclkcfg >> 16) & 0x3];
+}
diff --git a/arch/arm/mach-pxa/include/mach/smemc.h b/arch/arm/mach-pxa/smemc.h
index 9b2453a7ab23..9b2453a7ab23 100644
--- a/arch/arm/mach-pxa/include/mach/smemc.h
+++ b/arch/arm/mach-pxa/smemc.h
diff --git a/arch/arm/mach-pxa/spitz.c b/arch/arm/mach-pxa/spitz.c
index 371008e9bb02..9964729cd428 100644
--- a/arch/arm/mach-pxa/spitz.c
+++ b/arch/arm/mach-pxa/spitz.c
@@ -39,14 +39,14 @@
 
 #include "pxa27x.h"
 #include "pxa27x-udc.h"
-#include <mach/reset.h>
+#include "reset.h"
 #include <linux/platform_data/irda-pxaficp.h>
 #include <linux/platform_data/mmc-pxamci.h>
 #include <linux/platform_data/usb-ohci-pxa27x.h>
 #include <linux/platform_data/video-pxafb.h>
-#include <mach/spitz.h>
+#include "spitz.h"
 #include "sharpsl_pm.h"
-#include <mach/smemc.h>
+#include "smemc.h"
 
 #include "generic.h"
 #include "devices.h"
@@ -510,10 +510,6 @@ static struct ads7846_platform_data spitz_ads7846_info = {
 	.wait_for_sync		= spitz_ads7846_wait_for_hsync,
 };
 
-static struct pxa2xx_spi_chip spitz_ads7846_chip = {
-	.gpio_cs		= SPITZ_GPIO_ADS7846_CS,
-};
-
 static void spitz_bl_kick_battery(void)
 {
 	void (*kick_batt)(void);
@@ -555,14 +551,6 @@ static struct corgi_lcd_platform_data spitz_lcdcon_info = {
 	.kick_battery		= spitz_bl_kick_battery,
 };
 
-static struct pxa2xx_spi_chip spitz_lcdcon_chip = {
-	.gpio_cs	= SPITZ_GPIO_LCDCON_CS,
-};
-
-static struct pxa2xx_spi_chip spitz_max1111_chip = {
-	.gpio_cs	= SPITZ_GPIO_MAX1111_CS,
-};
-
 static struct spi_board_info spitz_spi_devices[] = {
 	{
 		.modalias		= "ads7846",
@@ -570,7 +558,6 @@ static struct spi_board_info spitz_spi_devices[] = {
 		.bus_num		= 2,
 		.chip_select		= 0,
 		.platform_data		= &spitz_ads7846_info,
-		.controller_data	= &spitz_ads7846_chip,
 		.irq			= PXA_GPIO_TO_IRQ(SPITZ_GPIO_TP_INT),
 	}, {
 		.modalias		= "corgi-lcd",
@@ -578,13 +565,11 @@ static struct spi_board_info spitz_spi_devices[] = {
 		.bus_num		= 2,
 		.chip_select		= 1,
 		.platform_data		= &spitz_lcdcon_info,
-		.controller_data	= &spitz_lcdcon_chip,
 	}, {
 		.modalias		= "max1111",
 		.max_speed_hz		= 450000,
 		.bus_num		= 2,
 		.chip_select		= 2,
-		.controller_data	= &spitz_max1111_chip,
 	},
 };
 
@@ -592,6 +577,16 @@ static struct pxa2xx_spi_controller spitz_spi_info = {
 	.num_chipselect	= 3,
 };
 
+static struct gpiod_lookup_table spitz_spi_gpio_table = {
+	.dev_id = "spi2",
+	.table = {
+		GPIO_LOOKUP_IDX("gpio-pxa", SPITZ_GPIO_ADS7846_CS, "cs", 0, GPIO_ACTIVE_LOW),
+		GPIO_LOOKUP_IDX("gpio-pxa", SPITZ_GPIO_LCDCON_CS, "cs", 1, GPIO_ACTIVE_LOW),
+		GPIO_LOOKUP_IDX("gpio-pxa", SPITZ_GPIO_MAX1111_CS, "cs", 2, GPIO_ACTIVE_LOW),
+		{ },
+	},
+};
+
 static void __init spitz_spi_init(void)
 {
 	if (machine_is_akita())
@@ -599,6 +594,7 @@ static void __init spitz_spi_init(void)
 	else
 		gpiod_add_lookup_table(&spitz_lcdcon_gpio_table);
 
+	gpiod_add_lookup_table(&spitz_spi_gpio_table);
 	pxa2xx_set_spi_info(2, &spitz_spi_info);
 	spi_register_board_info(ARRAY_AND_SIZE(spitz_spi_devices));
 }
@@ -966,11 +962,42 @@ static void __init spitz_i2c_init(void)
 static inline void spitz_i2c_init(void) {}
 #endif
 
+static struct gpiod_lookup_table spitz_audio_gpio_table = {
+	.dev_id = "spitz-audio",
+	.table = {
+		GPIO_LOOKUP("sharp-scoop.0", SPITZ_GPIO_MUTE_L - SPITZ_SCP_GPIO_BASE,
+			    "mute-l", GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP("sharp-scoop.0", SPITZ_GPIO_MUTE_R - SPITZ_SCP_GPIO_BASE,
+			    "mute-r", GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP("sharp-scoop.1", SPITZ_GPIO_MIC_BIAS - SPITZ_SCP2_GPIO_BASE,
+			    "mic", GPIO_ACTIVE_HIGH),
+		{ },
+	},
+};
+
+static struct gpiod_lookup_table akita_audio_gpio_table = {
+	.dev_id = "spitz-audio",
+	.table = {
+		GPIO_LOOKUP("sharp-scoop.0", SPITZ_GPIO_MUTE_L - SPITZ_SCP_GPIO_BASE,
+			    "mute-l", GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP("sharp-scoop.0", SPITZ_GPIO_MUTE_R - SPITZ_SCP_GPIO_BASE,
+			    "mute-r", GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP("i2c-max7310", AKITA_GPIO_MIC_BIAS - AKITA_IOEXP_GPIO_BASE,
+			    "mic", GPIO_ACTIVE_HIGH),
+		{ },
+	},
+};
+
 /******************************************************************************
  * Audio devices
  ******************************************************************************/
 static inline void spitz_audio_init(void)
 {
+	if (machine_is_akita())
+		gpiod_add_lookup_table(&akita_audio_gpio_table);
+	else
+		gpiod_add_lookup_table(&spitz_audio_gpio_table);
+
 	platform_device_register_simple("spitz-audio", -1, NULL, 0);
 }
 
diff --git a/arch/arm/mach-pxa/include/mach/spitz.h b/arch/arm/mach-pxa/spitz.h
index 04828d8918aa..04828d8918aa 100644
--- a/arch/arm/mach-pxa/include/mach/spitz.h
+++ b/arch/arm/mach-pxa/spitz.h
diff --git a/arch/arm/mach-pxa/spitz_pm.c b/arch/arm/mach-pxa/spitz_pm.c
index 25a1f8c5a738..6689b67f9ce5 100644
--- a/arch/arm/mach-pxa/spitz_pm.c
+++ b/arch/arm/mach-pxa/spitz_pm.c
@@ -18,9 +18,8 @@
 
 #include <asm/irq.h>
 #include <asm/mach-types.h>
-#include <mach/hardware.h>
 
-#include <mach/spitz.h>
+#include "spitz.h"
 #include "pxa27x.h"
 #include "sharpsl_pm.h"
 
diff --git a/arch/arm/mach-pxa/standby.S b/arch/arm/mach-pxa/standby.S
index eab1645bb4ad..ad32b9c0ebce 100644
--- a/arch/arm/mach-pxa/standby.S
+++ b/arch/arm/mach-pxa/standby.S
@@ -1,19 +1,16 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * PXA27x standby mode
  *
  * Author: David Burrage
  *
- * 2005 (c) MontaVista Software, Inc. This file is licensed under
- * the terms of the GNU General Public License version 2. This program
- * is licensed "as is" without any warranty of any kind, whether express
- * or implied.
+ * 2005 (c) MontaVista Software, Inc.
  */
 
 #include <linux/linkage.h>
 #include <asm/assembler.h>
-#include <mach/hardware.h>
 
-#include <mach/pxa2xx-regs.h>
+#include "pxa2xx-regs.h"
 
 		.text
 
diff --git a/arch/arm/mach-pxa/stargate2.c b/arch/arm/mach-pxa/stargate2.c
deleted file mode 100644
index 7ad627465768..000000000000
--- a/arch/arm/mach-pxa/stargate2.c
+++ /dev/null
@@ -1,1030 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- *  linux/arch/arm/mach-pxa/stargate2.c
- *
- *  Author:	Ed C. Epp
- *  Created:	Nov 05, 2002
- *  Copyright:	Intel Corp.
- *
- *  Modified 2009:  Jonathan Cameron <jic23@cam.ac.uk>
- */
-
-#include <linux/init.h>
-#include <linux/device.h>
-#include <linux/interrupt.h>
-#include <linux/sched.h>
-#include <linux/bitops.h>
-#include <linux/fb.h>
-#include <linux/delay.h>
-#include <linux/platform_device.h>
-#include <linux/regulator/machine.h>
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/plat-ram.h>
-#include <linux/mtd/partitions.h>
-
-#include <linux/platform_data/i2c-pxa.h>
-#include <linux/platform_data/pcf857x.h>
-#include <linux/smc91x.h>
-#include <linux/gpio/machine.h>
-#include <linux/gpio.h>
-#include <linux/leds.h>
-#include <linux/property.h>
-
-#include <asm/types.h>
-#include <asm/setup.h>
-#include <asm/memory.h>
-#include <asm/mach-types.h>
-#include <asm/irq.h>
-
-#include <asm/mach/arch.h>
-#include <asm/mach/map.h>
-#include <asm/mach/irq.h>
-#include <asm/mach/flash.h>
-
-#include "pxa27x.h"
-#include <linux/platform_data/mmc-pxamci.h>
-#include "udc.h"
-#include "pxa27x-udc.h"
-#include <mach/smemc.h>
-
-#include <linux/spi/spi.h>
-#include <linux/spi/pxa2xx_spi.h>
-#include <linux/mfd/da903x.h>
-
-#include "devices.h"
-#include "generic.h"
-
-#define STARGATE_NR_IRQS	(IRQ_BOARD_START + 8)
-
-/* Bluetooth */
-#define SG2_BT_RESET		81
-
-/* SD */
-#define SG2_GPIO_nSD_DETECT	90
-#define SG2_SD_POWER_ENABLE	89
-
-static unsigned long sg2_im2_unified_pin_config[] __initdata = {
-	/* Device Identification for wakeup*/
-	GPIO102_GPIO,
-	/* DA9030 */
-	GPIO1_GPIO,
-
-	/* MMC */
-	GPIO32_MMC_CLK,
-	GPIO112_MMC_CMD,
-	GPIO92_MMC_DAT_0,
-	GPIO109_MMC_DAT_1,
-	GPIO110_MMC_DAT_2,
-	GPIO111_MMC_DAT_3,
-
-	/* 802.15.4 radio - driver out of mainline */
-	GPIO22_GPIO,			/* CC_RSTN */
-	GPIO114_GPIO,			/* CC_FIFO */
-	GPIO116_GPIO,			/* CC_CCA */
-	GPIO0_GPIO,			/* CC_FIFOP */
-	GPIO16_GPIO,			/* CCSFD */
-	GPIO115_GPIO,			/* Power enable */
-
-	/* I2C */
-	GPIO117_I2C_SCL,
-	GPIO118_I2C_SDA,
-
-	/* SSP 3 - 802.15.4 radio */
-	GPIO39_GPIO,			/* Chip Select */
-	GPIO34_SSP3_SCLK,
-	GPIO35_SSP3_TXD,
-	GPIO41_SSP3_RXD,
-
-	/* SSP 2 to daughter boards */
-	GPIO11_SSP2_RXD,
-	GPIO38_SSP2_TXD,
-	GPIO36_SSP2_SCLK,
-	GPIO37_GPIO, /* chip select */
-
-	/* SSP 1 - to daughter boards */
-	GPIO24_GPIO,			/* Chip Select */
-	GPIO23_SSP1_SCLK,
-	GPIO25_SSP1_TXD,
-	GPIO26_SSP1_RXD,
-
-	/* BTUART Basic Connector*/
-	GPIO42_BTUART_RXD,
-	GPIO43_BTUART_TXD,
-	GPIO44_BTUART_CTS,
-	GPIO45_BTUART_RTS,
-
-	/* STUART  - IM2 via debug board not sure on SG2*/
-	GPIO46_STUART_RXD,
-	GPIO47_STUART_TXD,
-
-	/* Basic sensor board */
-	GPIO96_GPIO,	/* accelerometer interrupt */
-	GPIO99_GPIO,	/* ADC interrupt */
-
-	/* SHT15 */
-	GPIO100_GPIO,
-	GPIO98_GPIO,
-
-	/* Basic sensor board */
-	GPIO96_GPIO,	/* accelerometer interrupt */
-	GPIO99_GPIO,	/* ADC interrupt */
-
-	/* Connector pins specified as gpios */
-	GPIO94_GPIO, /* large basic connector pin 14 */
-	GPIO10_GPIO, /* large basic connector pin 23 */
-};
-
-static struct gpiod_lookup_table sht15_gpiod_table = {
-	.dev_id = "sht15",
-	.table = {
-		/* FIXME: should this have |GPIO_OPEN_DRAIN set? */
-		GPIO_LOOKUP("gpio-pxa", 100, "data", GPIO_ACTIVE_HIGH),
-		GPIO_LOOKUP("gpio-pxa", 98, "clk", GPIO_ACTIVE_HIGH),
-	},
-};
-
-static struct platform_device sht15 = {
-	.name = "sht15",
-	.id = -1,
-};
-
-static struct regulator_consumer_supply stargate2_sensor_3_con[] = {
-	REGULATOR_SUPPLY("vcc", "sht15"),
-};
-
-enum stargate2_ldos{
-	vcc_vref,
-	vcc_cc2420,
-	/* a mote connector? */
-	vcc_mica,
-	/* the CSR bluecore chip */
-	vcc_bt,
-	/* The two voltages available to sensor boards */
-	vcc_sensor_1_8,
-	vcc_sensor_3,
-	/* directly connected to the pxa27x */
-	vcc_sram_ext,
-	vcc_pxa_pll,
-	vcc_pxa_usim, /* Reference voltage for certain gpios */
-	vcc_pxa_mem,
-	vcc_pxa_flash,
-	vcc_pxa_core, /*Dc-Dc buck not yet supported */
-	vcc_lcd,
-	vcc_bb,
-	vcc_bbio, /*not sure!*/
-	vcc_io, /* cc2420 802.15.4 radio and pxa vcc_io ?*/
-};
-
-/* The values of the various regulator constraints are obviously dependent
- * on exactly what is wired to each ldo.  Unfortunately this information is
- * not generally available.  More information has been requested from Xbow.
- */
-static struct regulator_init_data stargate2_ldo_init_data[] = {
-	[vcc_bbio] = {
-		.constraints = { /* board default 1.8V */
-			.name = "vcc_bbio",
-			.min_uV = 1800000,
-			.max_uV = 1800000,
-		},
-	},
-	[vcc_bb] = {
-		.constraints = { /* board default 2.8V */
-			.name = "vcc_bb",
-			.min_uV = 2700000,
-			.max_uV = 3000000,
-		},
-	},
-	[vcc_pxa_flash] = {
-		.constraints = {/* default is 1.8V */
-			.name = "vcc_pxa_flash",
-			.min_uV = 1800000,
-			.max_uV = 1800000,
-		},
-	},
-	[vcc_cc2420] = { /* also vcc_io */
-		.constraints = {
-			/* board default is 2.8V */
-			.name = "vcc_cc2420",
-			.min_uV = 2700000,
-			.max_uV = 3300000,
-		},
-	},
-	[vcc_vref] = { /* Reference for what? */
-		.constraints = { /* default 1.8V */
-			.name = "vcc_vref",
-			.min_uV = 1800000,
-			.max_uV = 1800000,
-		},
-	},
-	[vcc_sram_ext] = {
-		.constraints = { /* default 2.8V */
-			.name = "vcc_sram_ext",
-			.min_uV = 2800000,
-			.max_uV = 2800000,
-		},
-	},
-	[vcc_mica] = {
-		.constraints = { /* default 2.8V */
-			.name = "vcc_mica",
-			.min_uV = 2800000,
-			.max_uV = 2800000,
-		},
-	},
-	[vcc_bt] = {
-		.constraints = { /* default 2.8V */
-			.name = "vcc_bt",
-			.min_uV = 2800000,
-			.max_uV = 2800000,
-		},
-	},
-	[vcc_lcd] = {
-		.constraints = { /* default 2.8V */
-			.name = "vcc_lcd",
-			.min_uV = 2700000,
-			.max_uV = 3300000,
-		},
-	},
-	[vcc_io] = { /* Same or higher than everything
-			  * bar vccbat and vccusb */
-		.constraints = { /* default 2.8V */
-			.name = "vcc_io",
-			.min_uV = 2692000,
-			.max_uV = 3300000,
-		},
-	},
-	[vcc_sensor_1_8] = {
-		.constraints = { /* default 1.8V */
-			.name = "vcc_sensor_1_8",
-			.min_uV = 1800000,
-			.max_uV = 1800000,
-		},
-	},
-	[vcc_sensor_3] = { /* curiously default 2.8V */
-		.constraints = {
-			.name = "vcc_sensor_3",
-			.min_uV = 2800000,
-			.max_uV = 3000000,
-		},
-		.num_consumer_supplies = ARRAY_SIZE(stargate2_sensor_3_con),
-		.consumer_supplies = stargate2_sensor_3_con,
-	},
-	[vcc_pxa_pll] = { /* 1.17V - 1.43V, default 1.3V*/
-		.constraints = {
-			.name = "vcc_pxa_pll",
-			.min_uV = 1170000,
-			.max_uV = 1430000,
-		},
-	},
-	[vcc_pxa_usim] = {
-		.constraints = { /* default 1.8V */
-			.name = "vcc_pxa_usim",
-			.min_uV = 1710000,
-			.max_uV = 2160000,
-		},
-	},
-	[vcc_pxa_mem] = {
-		.constraints = { /* default 1.8V */
-			.name = "vcc_pxa_mem",
-			.min_uV = 1800000,
-			.max_uV = 1800000,
-		},
-	},
-};
-
-static struct mtd_partition stargate2flash_partitions[] = {
-	{
-		.name = "Bootloader",
-		.size = 0x00040000,
-		.offset = 0,
-		.mask_flags = 0,
-	}, {
-		.name = "Kernel",
-		.size = 0x00200000,
-		.offset = 0x00040000,
-		.mask_flags = 0
-	}, {
-		.name = "Filesystem",
-		.size = 0x01DC0000,
-		.offset = 0x00240000,
-		.mask_flags = 0
-	},
-};
-
-static struct resource flash_resources = {
-	.start = PXA_CS0_PHYS,
-	.end = PXA_CS0_PHYS + SZ_32M - 1,
-	.flags = IORESOURCE_MEM,
-};
-
-static struct flash_platform_data stargate2_flash_data = {
-	.map_name = "cfi_probe",
-	.parts = stargate2flash_partitions,
-	.nr_parts = ARRAY_SIZE(stargate2flash_partitions),
-	.name = "PXA27xOnChipROM",
-	.width = 2,
-};
-
-static struct platform_device stargate2_flash_device = {
-	.name = "pxa2xx-flash",
-	.id = 0,
-	.dev = {
-		.platform_data = &stargate2_flash_data,
-	},
-	.resource = &flash_resources,
-	.num_resources = 1,
-};
-
-static struct pxa2xx_spi_controller pxa_ssp_master_0_info = {
-	.num_chipselect = 1,
-};
-
-static struct pxa2xx_spi_controller pxa_ssp_master_1_info = {
-	.num_chipselect = 1,
-};
-
-static struct pxa2xx_spi_controller pxa_ssp_master_2_info = {
-	.num_chipselect = 1,
-};
-
-/* An upcoming kernel change will scrap SFRM usage so these
- * drivers have been moved to use gpio's via cs_control */
-static struct pxa2xx_spi_chip staccel_chip_info = {
-	.tx_threshold = 8,
-	.rx_threshold = 8,
-	.dma_burst_size = 8,
-	.timeout = 235,
-	.gpio_cs = 24,
-};
-
-static struct pxa2xx_spi_chip cc2420_info = {
-	.tx_threshold = 8,
-	.rx_threshold = 8,
-	.dma_burst_size = 8,
-	.timeout = 235,
-	.gpio_cs = 39,
-};
-
-static struct spi_board_info spi_board_info[] __initdata = {
-	{
-		.modalias = "lis3l02dq",
-		.max_speed_hz = 8000000,/* 8MHz max spi frequency at 3V */
-		.bus_num = 1,
-		.chip_select = 0,
-		.controller_data = &staccel_chip_info,
-		.irq = PXA_GPIO_TO_IRQ(96),
-	}, {
-		.modalias = "cc2420",
-		.max_speed_hz = 6500000,
-		.bus_num = 3,
-		.chip_select = 0,
-		.controller_data = &cc2420_info,
-	},
-};
-
-static void sg2_udc_command(int cmd)
-{
-	switch (cmd) {
-	case PXA2XX_UDC_CMD_CONNECT:
-		UP2OCR |=  UP2OCR_HXOE  | UP2OCR_DPPUE | UP2OCR_DPPUBE;
-		break;
-	case PXA2XX_UDC_CMD_DISCONNECT:
-		UP2OCR &= ~(UP2OCR_HXOE  | UP2OCR_DPPUE | UP2OCR_DPPUBE);
-		break;
-	}
-}
-
-static struct i2c_pxa_platform_data i2c_pwr_pdata = {
-	.fast_mode = 1,
-};
-
-static struct i2c_pxa_platform_data i2c_pdata = {
-	.fast_mode = 1,
-};
-
-static void __init imote2_stargate2_init(void)
-{
-
-	pxa2xx_mfp_config(ARRAY_AND_SIZE(sg2_im2_unified_pin_config));
-
-	pxa_set_ffuart_info(NULL);
-	pxa_set_btuart_info(NULL);
-	pxa_set_stuart_info(NULL);
-
-	pxa2xx_set_spi_info(1, &pxa_ssp_master_0_info);
-	pxa2xx_set_spi_info(2, &pxa_ssp_master_1_info);
-	pxa2xx_set_spi_info(3, &pxa_ssp_master_2_info);
-	spi_register_board_info(spi_board_info, ARRAY_SIZE(spi_board_info));
-
-
-	pxa27x_set_i2c_power_info(&i2c_pwr_pdata);
-	pxa_set_i2c_info(&i2c_pdata);
-}
-
-#ifdef CONFIG_MACH_INTELMOTE2
-/* As the the imote2 doesn't currently have a conventional SD slot
- * there is no option to hotplug cards, making all this rather simple
- */
-static int imote2_mci_get_ro(struct device *dev)
-{
-	return 0;
-}
-
-/* Rather simple case as hotplugging not possible */
-static struct pxamci_platform_data imote2_mci_platform_data = {
-	.ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34, /* default anyway */
-	.get_ro = imote2_mci_get_ro,
-};
-
-static struct gpio_led imote2_led_pins[] = {
-	{
-		.name       =  "imote2:red",
-		.gpio       = 103,
-		.active_low = 1,
-	}, {
-		.name       = "imote2:green",
-		.gpio       = 104,
-		.active_low = 1,
-	}, {
-		.name       = "imote2:blue",
-		.gpio       = 105,
-		.active_low = 1,
-	},
-};
-
-static struct gpio_led_platform_data imote2_led_data = {
-	.num_leds = ARRAY_SIZE(imote2_led_pins),
-	.leds     = imote2_led_pins,
-};
-
-static struct platform_device imote2_leds = {
-	.name = "leds-gpio",
-	.id   = -1,
-	.dev = {
-		.platform_data = &imote2_led_data,
-	},
-};
-
-static struct da903x_subdev_info imote2_da9030_subdevs[] = {
-	{
-		.name = "da903x-regulator",
-		.id = DA9030_ID_LDO2,
-		.platform_data = &stargate2_ldo_init_data[vcc_bbio],
-	}, {
-		.name = "da903x-regulator",
-		.id = DA9030_ID_LDO3,
-		.platform_data = &stargate2_ldo_init_data[vcc_bb],
-	}, {
-		.name = "da903x-regulator",
-		.id = DA9030_ID_LDO4,
-		.platform_data = &stargate2_ldo_init_data[vcc_pxa_flash],
-	}, {
-		.name = "da903x-regulator",
-		.id = DA9030_ID_LDO5,
-		.platform_data = &stargate2_ldo_init_data[vcc_cc2420],
-	}, {
-		.name = "da903x-regulator",
-		.id = DA9030_ID_LDO6,
-		.platform_data = &stargate2_ldo_init_data[vcc_vref],
-	}, {
-		.name = "da903x-regulator",
-		.id = DA9030_ID_LDO7,
-		.platform_data = &stargate2_ldo_init_data[vcc_sram_ext],
-	}, {
-		.name = "da903x-regulator",
-		.id = DA9030_ID_LDO8,
-		.platform_data = &stargate2_ldo_init_data[vcc_mica],
-	}, {
-		.name = "da903x-regulator",
-		.id = DA9030_ID_LDO9,
-		.platform_data = &stargate2_ldo_init_data[vcc_bt],
-	}, {
-		.name = "da903x-regulator",
-		.id = DA9030_ID_LDO10,
-		.platform_data = &stargate2_ldo_init_data[vcc_sensor_1_8],
-	}, {
-		.name = "da903x-regulator",
-		.id = DA9030_ID_LDO11,
-		.platform_data = &stargate2_ldo_init_data[vcc_sensor_3],
-	}, {
-		.name = "da903x-regulator",
-		.id = DA9030_ID_LDO12,
-		.platform_data = &stargate2_ldo_init_data[vcc_lcd],
-	}, {
-		.name = "da903x-regulator",
-		.id = DA9030_ID_LDO15,
-		.platform_data = &stargate2_ldo_init_data[vcc_pxa_pll],
-	}, {
-		.name = "da903x-regulator",
-		.id = DA9030_ID_LDO17,
-		.platform_data = &stargate2_ldo_init_data[vcc_pxa_usim],
-	}, {
-		.name = "da903x-regulator", /*pxa vcc i/o and cc2420 vcc i/o */
-		.id = DA9030_ID_LDO18,
-		.platform_data = &stargate2_ldo_init_data[vcc_io],
-	}, {
-		.name = "da903x-regulator",
-		.id = DA9030_ID_LDO19,
-		.platform_data = &stargate2_ldo_init_data[vcc_pxa_mem],
-	},
-};
-
-static struct da903x_platform_data imote2_da9030_pdata = {
-	.num_subdevs = ARRAY_SIZE(imote2_da9030_subdevs),
-	.subdevs = imote2_da9030_subdevs,
-};
-
-static struct i2c_board_info __initdata imote2_pwr_i2c_board_info[] = {
-	{
-		.type = "da9030",
-		.addr = 0x49,
-		.platform_data = &imote2_da9030_pdata,
-		.irq = PXA_GPIO_TO_IRQ(1),
-	},
-};
-
-static struct i2c_board_info __initdata imote2_i2c_board_info[] = {
-	{ /* UCAM sensor board */
-		.type = "max1239",
-		.addr = 0x35,
-	}, { /* ITS400 Sensor board only */
-		.type = "max1363",
-		.addr = 0x34,
-		/* Through a nand gate - Also beware, on V2 sensor board the
-		 * pull up resistors are missing.
-		 */
-		.irq = PXA_GPIO_TO_IRQ(99),
-	}, { /* ITS400 Sensor board only */
-		.type = "tsl2561",
-		.addr = 0x49,
-		/* Through a nand gate - Also beware, on V2 sensor board the
-		 * pull up resistors are missing.
-		 */
-		.irq = PXA_GPIO_TO_IRQ(99),
-	}, { /* ITS400 Sensor board only */
-		.type = "tmp175",
-		.addr = 0x4A,
-		.irq = PXA_GPIO_TO_IRQ(96),
-	}, { /* IMB400 Multimedia board */
-		.type = "wm8940",
-		.addr = 0x1A,
-	},
-};
-
-static unsigned long imote2_pin_config[] __initdata = {
-
-	/* Button */
-	GPIO91_GPIO,
-
-	/* LEDS */
-	GPIO103_GPIO, /* red led */
-	GPIO104_GPIO, /* green led */
-	GPIO105_GPIO, /* blue led */
-};
-
-static struct pxa2xx_udc_mach_info imote2_udc_info __initdata = {
-	.udc_command		= sg2_udc_command,
-};
-
-static struct platform_device imote2_audio_device = {
-	.name = "imote2-audio",
-	.id   = -1,
-};
-
-static struct platform_device *imote2_devices[] = {
-	&stargate2_flash_device,
-	&imote2_leds,
-	&sht15,
-	&imote2_audio_device,
-};
-
-static void __init imote2_init(void)
-{
-	pxa2xx_mfp_config(ARRAY_AND_SIZE(imote2_pin_config));
-
-	imote2_stargate2_init();
-
-	gpiod_add_lookup_table(&sht15_gpiod_table);
-	platform_add_devices(imote2_devices, ARRAY_SIZE(imote2_devices));
-
-	i2c_register_board_info(0, imote2_i2c_board_info,
-				ARRAY_SIZE(imote2_i2c_board_info));
-	i2c_register_board_info(1, imote2_pwr_i2c_board_info,
-				ARRAY_SIZE(imote2_pwr_i2c_board_info));
-
-	pxa_set_mci_info(&imote2_mci_platform_data);
-	pxa_set_udc_info(&imote2_udc_info);
-}
-#endif
-
-#ifdef CONFIG_MACH_STARGATE2
-
-static unsigned long stargate2_pin_config[] __initdata = {
-
-	GPIO15_nCS_1, /* SRAM */
-	/* SMC91x */
-	GPIO80_nCS_4,
-	GPIO40_GPIO, /*cable detect?*/
-
-	/* Button */
-	GPIO91_GPIO | WAKEUP_ON_LEVEL_HIGH,
-
-	/* Compact Flash */
-	GPIO79_PSKTSEL,
-	GPIO48_nPOE,
-	GPIO49_nPWE,
-	GPIO50_nPIOR,
-	GPIO51_nPIOW,
-	GPIO85_nPCE_1,
-	GPIO54_nPCE_2,
-	GPIO55_nPREG,
-	GPIO56_nPWAIT,
-	GPIO57_nIOIS16,
-	GPIO120_GPIO, /* Buff ctrl */
-	GPIO108_GPIO, /* Power ctrl */
-	GPIO82_GPIO, /* Reset */
-	GPIO53_GPIO, /* SG2_S0_GPIO_DETECT */
-
-	/* MMC not shared with imote2 */
-	GPIO90_GPIO, /* nSD detect */
-	GPIO89_GPIO, /* SD_POWER_ENABLE */
-
-	/* Bluetooth */
-	GPIO81_GPIO, /* reset */
-};
-
-static struct resource smc91x_resources[] = {
-	[0] = {
-		.name = "smc91x-regs",
-		.start = (PXA_CS4_PHYS + 0x300),
-		.end = (PXA_CS4_PHYS + 0xfffff),
-		.flags = IORESOURCE_MEM,
-	},
-	[1] = {
-		.start = PXA_GPIO_TO_IRQ(40),
-		.end = PXA_GPIO_TO_IRQ(40),
-		.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE,
-	}
-};
-
-static struct smc91x_platdata stargate2_smc91x_info = {
-	.flags = SMC91X_USE_8BIT | SMC91X_USE_16BIT | SMC91X_USE_32BIT
-	| SMC91X_NOWAIT | SMC91X_USE_DMA,
-	.pxa_u16_align4 = true,
-};
-
-static struct platform_device smc91x_device = {
-	.name = "smc91x",
-	.id = -1,
-	.num_resources = ARRAY_SIZE(smc91x_resources),
-	.resource = smc91x_resources,
-	.dev = {
-		.platform_data = &stargate2_smc91x_info,
-	},
-};
-
-
-/*
- * The card detect interrupt isn't debounced so we delay it by 250ms
- * to give the card a chance to fully insert / eject.
- */
-static int stargate2_mci_init(struct device *dev,
-			      irq_handler_t stargate2_detect_int,
-			      void *data)
-{
-	int err;
-
-	err = gpio_request(SG2_SD_POWER_ENABLE, "SG2_sd_power_enable");
-	if (err) {
-		printk(KERN_ERR "Can't get the gpio for SD power control");
-		goto return_err;
-	}
-	gpio_direction_output(SG2_SD_POWER_ENABLE, 0);
-
-	err = gpio_request(SG2_GPIO_nSD_DETECT, "SG2_sd_detect");
-	if (err) {
-		printk(KERN_ERR "Can't get the sd detect gpio");
-		goto free_power_en;
-	}
-	gpio_direction_input(SG2_GPIO_nSD_DETECT);
-
-	err = request_irq(PXA_GPIO_TO_IRQ(SG2_GPIO_nSD_DETECT),
-			  stargate2_detect_int,
-			  IRQ_TYPE_EDGE_BOTH,
-			  "MMC card detect",
-			  data);
-	if (err) {
-		printk(KERN_ERR "can't request MMC card detect IRQ\n");
-		goto free_nsd_detect;
-	}
-	return 0;
-
- free_nsd_detect:
-	gpio_free(SG2_GPIO_nSD_DETECT);
- free_power_en:
-	gpio_free(SG2_SD_POWER_ENABLE);
- return_err:
-	return err;
-}
-
-/**
- * stargate2_mci_setpower() - set state of mmc power supply
- *
- * Very simple control. Either it is on or off and is controlled by
- * a gpio pin */
-static int stargate2_mci_setpower(struct device *dev, unsigned int vdd)
-{
-	gpio_set_value(SG2_SD_POWER_ENABLE, !!vdd);
-	return 0;
-}
-
-static void stargate2_mci_exit(struct device *dev, void *data)
-{
-	free_irq(PXA_GPIO_TO_IRQ(SG2_GPIO_nSD_DETECT), data);
-	gpio_free(SG2_SD_POWER_ENABLE);
-	gpio_free(SG2_GPIO_nSD_DETECT);
-}
-
-static struct pxamci_platform_data stargate2_mci_platform_data = {
-	.detect_delay_ms = 250,
-	.ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34,
-	.init = stargate2_mci_init,
-	.setpower = stargate2_mci_setpower,
-	.exit = stargate2_mci_exit,
-};
-
-
-/*
- * SRAM - The Stargate 2 has 32MB of SRAM.
- *
- * Here it is made available as an MTD. This will then
- * typically have a cifs filesystem created on it to provide
- * fast temporary storage.
- */
-static struct resource sram_resources = {
-	.start = PXA_CS1_PHYS,
-	.end = PXA_CS1_PHYS + SZ_32M-1,
-	.flags = IORESOURCE_MEM,
-};
-
-static struct platdata_mtd_ram stargate2_sram_pdata = {
-	.mapname = "Stargate2 SRAM",
-	.bankwidth = 2,
-};
-
-static struct platform_device stargate2_sram = {
-	.name = "mtd-ram",
-	.id = 0,
-	.resource = &sram_resources,
-	.num_resources = 1,
-	.dev = {
-		.platform_data = &stargate2_sram_pdata,
-	},
-};
-
-static struct pcf857x_platform_data platform_data_pcf857x = {
-	.gpio_base = 128,
-	.n_latch = 0,
-	.setup = NULL,
-	.teardown = NULL,
-	.context = NULL,
-};
-
-static const struct property_entry pca9500_eeprom_properties[] = {
-	PROPERTY_ENTRY_U32("pagesize", 4),
-	{ }
-};
-
-static const struct software_node pca9500_eeprom_node = {
-	.properties = pca9500_eeprom_properties,
-};
-
-/**
- * stargate2_reset_bluetooth() reset the bluecore to ensure consistent state
- **/
-static int stargate2_reset_bluetooth(void)
-{
-	int err;
-	err = gpio_request(SG2_BT_RESET, "SG2_BT_RESET");
-	if (err) {
-		printk(KERN_ERR "Could not get gpio for bluetooth reset\n");
-		return err;
-	}
-	gpio_direction_output(SG2_BT_RESET, 1);
-	mdelay(5);
-	/* now reset it - 5 msec minimum */
-	gpio_set_value(SG2_BT_RESET, 0);
-	mdelay(10);
-	gpio_set_value(SG2_BT_RESET, 1);
-	gpio_free(SG2_BT_RESET);
-	return 0;
-}
-
-static struct led_info stargate2_leds[] = {
-	{
-		.name = "sg2:red",
-		.flags = DA9030_LED_RATE_ON,
-	}, {
-		.name = "sg2:blue",
-		.flags = DA9030_LED_RATE_ON,
-	}, {
-		.name = "sg2:green",
-		.flags = DA9030_LED_RATE_ON,
-	},
-};
-
-static struct da903x_subdev_info stargate2_da9030_subdevs[] = {
-	{
-		.name = "da903x-led",
-		.id = DA9030_ID_LED_2,
-		.platform_data = &stargate2_leds[0],
-	}, {
-		.name = "da903x-led",
-		.id = DA9030_ID_LED_3,
-		.platform_data = &stargate2_leds[2],
-	}, {
-		.name = "da903x-led",
-		.id = DA9030_ID_LED_4,
-		.platform_data = &stargate2_leds[1],
-	}, {
-		.name = "da903x-regulator",
-		.id = DA9030_ID_LDO2,
-		.platform_data = &stargate2_ldo_init_data[vcc_bbio],
-	}, {
-		.name = "da903x-regulator",
-		.id = DA9030_ID_LDO3,
-		.platform_data = &stargate2_ldo_init_data[vcc_bb],
-	}, {
-		.name = "da903x-regulator",
-		.id = DA9030_ID_LDO4,
-		.platform_data = &stargate2_ldo_init_data[vcc_pxa_flash],
-	}, {
-		.name = "da903x-regulator",
-		.id = DA9030_ID_LDO5,
-		.platform_data = &stargate2_ldo_init_data[vcc_cc2420],
-	}, {
-		.name = "da903x-regulator",
-		.id = DA9030_ID_LDO6,
-		.platform_data = &stargate2_ldo_init_data[vcc_vref],
-	}, {
-		.name = "da903x-regulator",
-		.id = DA9030_ID_LDO7,
-		.platform_data = &stargate2_ldo_init_data[vcc_sram_ext],
-	}, {
-		.name = "da903x-regulator",
-		.id = DA9030_ID_LDO8,
-		.platform_data = &stargate2_ldo_init_data[vcc_mica],
-	}, {
-		.name = "da903x-regulator",
-		.id = DA9030_ID_LDO9,
-		.platform_data = &stargate2_ldo_init_data[vcc_bt],
-	}, {
-		.name = "da903x-regulator",
-		.id = DA9030_ID_LDO10,
-		.platform_data = &stargate2_ldo_init_data[vcc_sensor_1_8],
-	}, {
-		.name = "da903x-regulator",
-		.id = DA9030_ID_LDO11,
-		.platform_data = &stargate2_ldo_init_data[vcc_sensor_3],
-	}, {
-		.name = "da903x-regulator",
-		.id = DA9030_ID_LDO12,
-		.platform_data = &stargate2_ldo_init_data[vcc_lcd],
-	}, {
-		.name = "da903x-regulator",
-		.id = DA9030_ID_LDO15,
-		.platform_data = &stargate2_ldo_init_data[vcc_pxa_pll],
-	}, {
-		.name = "da903x-regulator",
-		.id = DA9030_ID_LDO17,
-		.platform_data = &stargate2_ldo_init_data[vcc_pxa_usim],
-	}, {
-		.name = "da903x-regulator", /*pxa vcc i/o and cc2420 vcc i/o */
-		.id = DA9030_ID_LDO18,
-		.platform_data = &stargate2_ldo_init_data[vcc_io],
-	}, {
-		.name = "da903x-regulator",
-		.id = DA9030_ID_LDO19,
-		.platform_data = &stargate2_ldo_init_data[vcc_pxa_mem],
-	},
-};
-
-static struct da903x_platform_data stargate2_da9030_pdata = {
-	.num_subdevs = ARRAY_SIZE(stargate2_da9030_subdevs),
-	.subdevs = stargate2_da9030_subdevs,
-};
-
-static struct i2c_board_info __initdata stargate2_pwr_i2c_board_info[] = {
-	{
-		.type = "da9030",
-		.addr = 0x49,
-		.platform_data = &stargate2_da9030_pdata,
-		.irq = PXA_GPIO_TO_IRQ(1),
-	},
-};
-
-static struct i2c_board_info __initdata stargate2_i2c_board_info[] = {
-	/* Techically this a pca9500 - but it's compatible with the 8574
-	 * for gpio expansion and the 24c02 for eeprom access.
-	 */
-	{
-		.type = "pcf8574",
-		.addr =  0x27,
-		.platform_data = &platform_data_pcf857x,
-	}, {
-		.type = "24c02",
-		.addr = 0x57,
-		.swnode = &pca9500_eeprom_node,
-	}, {
-		.type = "max1238",
-		.addr = 0x35,
-	}, { /* ITS400 Sensor board only */
-		.type = "max1363",
-		.addr = 0x34,
-		/* Through a nand gate - Also beware, on V2 sensor board the
-		 * pull up resistors are missing.
-		 */
-		.irq = PXA_GPIO_TO_IRQ(99),
-	}, { /* ITS400 Sensor board only */
-		.type = "tsl2561",
-		.addr = 0x49,
-		/* Through a nand gate - Also beware, on V2 sensor board the
-		 * pull up resistors are missing.
-		 */
-		.irq = PXA_GPIO_TO_IRQ(99),
-	}, { /* ITS400 Sensor board only */
-		.type = "tmp175",
-		.addr = 0x4A,
-		.irq = PXA_GPIO_TO_IRQ(96),
-	},
-};
-
-/* Board doesn't support cable detection - so always lie and say
- * something is there.
- */
-static int sg2_udc_detect(void)
-{
-	return 1;
-}
-
-static struct pxa2xx_udc_mach_info stargate2_udc_info __initdata = {
-	.udc_is_connected	= sg2_udc_detect,
-	.udc_command		= sg2_udc_command,
-};
-
-static struct platform_device *stargate2_devices[] = {
-	&stargate2_flash_device,
-	&stargate2_sram,
-	&smc91x_device,
-	&sht15,
-};
-
-static void __init stargate2_init(void)
-{
-	/* This is probably a board specific hack as this must be set
-	   prior to connecting the MFP stuff up. */
-	__raw_writel(__raw_readl(MECR) & ~MECR_NOS, MECR);
-
-	pxa2xx_mfp_config(ARRAY_AND_SIZE(stargate2_pin_config));
-
-	imote2_stargate2_init();
-
-	gpiod_add_lookup_table(&sht15_gpiod_table);
-	platform_add_devices(ARRAY_AND_SIZE(stargate2_devices));
-
-	i2c_register_board_info(0, ARRAY_AND_SIZE(stargate2_i2c_board_info));
-	i2c_register_board_info(1, stargate2_pwr_i2c_board_info,
-				ARRAY_SIZE(stargate2_pwr_i2c_board_info));
-
-	pxa_set_mci_info(&stargate2_mci_platform_data);
-
-	pxa_set_udc_info(&stargate2_udc_info);
-
-	stargate2_reset_bluetooth();
-}
-#endif
-
-#ifdef CONFIG_MACH_INTELMOTE2
-MACHINE_START(INTELMOTE2, "IMOTE 2")
-	.map_io		= pxa27x_map_io,
-	.nr_irqs	= PXA_NR_IRQS,
-	.init_irq	= pxa27x_init_irq,
-	.handle_irq	= pxa27x_handle_irq,
-	.init_time	= pxa_timer_init,
-	.init_machine	= imote2_init,
-	.atag_offset	= 0x100,
-	.restart	= pxa_restart,
-MACHINE_END
-#endif
-
-#ifdef CONFIG_MACH_STARGATE2
-MACHINE_START(STARGATE2, "Stargate 2")
-	.map_io = pxa27x_map_io,
-	.nr_irqs = STARGATE_NR_IRQS,
-	.init_irq = pxa27x_init_irq,
-	.handle_irq = pxa27x_handle_irq,
-	.init_time	= pxa_timer_init,
-	.init_machine = stargate2_init,
-	.atag_offset = 0x100,
-	.restart	= pxa_restart,
-MACHINE_END
-#endif
diff --git a/arch/arm/mach-pxa/tosa.c b/arch/arm/mach-pxa/tosa.c
index 431709725d02..d41641d6cfcd 100644
--- a/arch/arm/mach-pxa/tosa.c
+++ b/arch/arm/mach-pxa/tosa.c
@@ -40,16 +40,16 @@
 #include <asm/mach-types.h>
 
 #include "pxa25x.h"
-#include <mach/reset.h>
+#include "reset.h"
 #include <linux/platform_data/irda-pxaficp.h>
 #include <linux/platform_data/mmc-pxamci.h>
 #include "udc.h"
 #include "tosa_bt.h"
-#include <mach/audio.h>
-#include <mach/smemc.h>
+#include <linux/platform_data/asoc-pxa.h>
+#include "smemc.h"
 
 #include <asm/mach/arch.h>
-#include <mach/tosa.h>
+#include "tosa.h"
 
 #include <asm/hardware/scoop.h>
 #include <asm/mach/sharpsl_param.h>
@@ -296,9 +296,9 @@ static struct gpiod_lookup_table tosa_mci_gpio_table = {
 	.table = {
 		GPIO_LOOKUP("gpio-pxa", TOSA_GPIO_nSD_DETECT,
 			    "cd", GPIO_ACTIVE_LOW),
-		GPIO_LOOKUP("gpio-pxa", TOSA_GPIO_SD_WP,
+		GPIO_LOOKUP("sharp-scoop.0", TOSA_GPIO_SD_WP - TOSA_SCOOP_GPIO_BASE,
 			    "wp", GPIO_ACTIVE_LOW),
-		GPIO_LOOKUP("gpio-pxa", TOSA_GPIO_PWR_ON,
+		GPIO_LOOKUP("sharp-scoop.0", TOSA_GPIO_PWR_ON - TOSA_SCOOP_GPIO_BASE,
 			    "power", GPIO_ACTIVE_HIGH),
 		{ },
 	},
@@ -616,6 +616,22 @@ static struct resource tc6393xb_resources[] = {
 	},
 };
 
+static struct gpiod_lookup_table tosa_battery_gpio_table = {
+	.dev_id = "wm97xx-battery",
+	.table = {
+		GPIO_LOOKUP("gpio-pxa", TOSA_GPIO_BAT0_CRG,
+			    "main battery full", GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP("gpio-pxa", TOSA_GPIO_BAT1_CRG,
+			    "jacket battery full", GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP("gpio-pxa", TOSA_GPIO_BAT0_LOW,
+			    "main battery low", GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP("gpio-pxa", TOSA_GPIO_BAT1_LOW,
+			    "jacket battery low", GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP("gpio-pxa", TOSA_GPIO_JACKET_DETECT,
+			    "jacket detect", GPIO_ACTIVE_HIGH),
+		{ },
+	},
+};
 
 static int tosa_tc6393xb_enable(struct platform_device *dev)
 {
@@ -662,13 +678,11 @@ err_req_pclr:
 	return rc;
 }
 
-static int tosa_tc6393xb_disable(struct platform_device *dev)
+static void tosa_tc6393xb_disable(struct platform_device *dev)
 {
 	gpio_free(TOSA_GPIO_TC6393XB_L3V_ON);
 	gpio_free(TOSA_GPIO_TC6393XB_SUSPEND);
 	gpio_free(TOSA_GPIO_TC6393XB_REST_IN);
-
-	return 0;
 }
 
 static int tosa_tc6393xb_resume(struct platform_device *dev)
@@ -709,31 +723,6 @@ static struct tmio_nand_data tosa_tc6393xb_nand_config = {
 	.part_parsers = probes,
 };
 
-static int tosa_tc6393xb_setup(struct platform_device *dev)
-{
-	int rc;
-
-	rc = gpio_request(TOSA_GPIO_CARD_VCC_ON, "CARD_VCC_ON");
-	if (rc)
-		goto err_req;
-
-	rc = gpio_direction_output(TOSA_GPIO_CARD_VCC_ON, 1);
-	if (rc)
-		goto err_dir;
-
-	return rc;
-
-err_dir:
-	gpio_free(TOSA_GPIO_CARD_VCC_ON);
-err_req:
-	return rc;
-}
-
-static void tosa_tc6393xb_teardown(struct platform_device *dev)
-{
-	gpio_free(TOSA_GPIO_CARD_VCC_ON);
-}
-
 #ifdef CONFIG_MFD_TC6393XB
 static struct fb_videomode tosa_tc6393xb_lcd_mode[] = {
 	{
@@ -778,9 +767,6 @@ static struct tc6393xb_platform_data tosa_tc6393xb_data = {
 	.scr_gper	= 0x3300,
 
 	.irq_base	= IRQ_BOARD_START,
-	.gpio_base	= TOSA_TC6393XB_GPIO_BASE,
-	.setup		= tosa_tc6393xb_setup,
-	.teardown	= tosa_tc6393xb_teardown,
 
 	.enable		= tosa_tc6393xb_enable,
 	.disable	= tosa_tc6393xb_disable,
@@ -821,26 +807,6 @@ static struct pxa2xx_spi_controller pxa_ssp_master_info = {
 	.num_chipselect	= 1,
 };
 
-static struct gpiod_lookup_table tosa_lcd_gpio_table = {
-	.dev_id = "spi2.0",
-	.table = {
-		GPIO_LOOKUP("tc6393xb",
-			    TOSA_GPIO_TG_ON - TOSA_TC6393XB_GPIO_BASE,
-			    "tg #pwr", GPIO_ACTIVE_HIGH),
-		{ },
-	},
-};
-
-static struct gpiod_lookup_table tosa_lcd_bl_gpio_table = {
-	.dev_id = "i2c-tosa-bl",
-	.table = {
-		GPIO_LOOKUP("tc6393xb",
-			    TOSA_GPIO_BL_C20MA - TOSA_TC6393XB_GPIO_BASE,
-			    "backlight", GPIO_ACTIVE_HIGH),
-		{ },
-	},
-};
-
 static struct spi_board_info spi_board_info[] __initdata = {
 	{
 		.modalias	= "tosa-lcd",
@@ -943,6 +909,8 @@ static void __init tosa_init(void)
 	/* enable batt_fault */
 	PMCR = 0x01;
 
+	gpiod_add_lookup_table(&tosa_battery_gpio_table);
+
 	gpiod_add_lookup_table(&tosa_mci_gpio_table);
 	pxa_set_mci_info(&tosa_mci_platform_data);
 	pxa_set_ficp_info(&tosa_ficp_platform_data);
@@ -951,8 +919,6 @@ static void __init tosa_init(void)
 	platform_scoop_config = &tosa_pcmcia_config;
 
 	pxa2xx_set_spi_info(2, &pxa_ssp_master_info);
-	gpiod_add_lookup_table(&tosa_lcd_gpio_table);
-	gpiod_add_lookup_table(&tosa_lcd_bl_gpio_table);
 	spi_register_board_info(spi_board_info, ARRAY_SIZE(spi_board_info));
 
 	clk_add_alias("CLK_CK3P6MI", tc6393xb_device.name, "GPIO11_CLK", NULL);
diff --git a/arch/arm/mach-pxa/include/mach/tosa.h b/arch/arm/mach-pxa/tosa.h
index 8bfaca3a8b64..3b3efa0a0e22 100644
--- a/arch/arm/mach-pxa/include/mach/tosa.h
+++ b/arch/arm/mach-pxa/tosa.h
@@ -55,24 +55,6 @@
 #define TOSA_SCOOP_JC_IO_DIR (TOSA_SCOOP_JC_CARD_LIMIT_SEL)
 
 /*
- * TC6393XB GPIOs
- */
-#define TOSA_TC6393XB_GPIO_BASE		(PXA_NR_BUILTIN_GPIO + 2 * 12)
-
-#define TOSA_GPIO_TG_ON			(TOSA_TC6393XB_GPIO_BASE + 0)
-#define TOSA_GPIO_L_MUTE		(TOSA_TC6393XB_GPIO_BASE + 1)
-#define TOSA_GPIO_BL_C20MA		(TOSA_TC6393XB_GPIO_BASE + 3)
-#define TOSA_GPIO_CARD_VCC_ON		(TOSA_TC6393XB_GPIO_BASE + 4)
-#define TOSA_GPIO_CHARGE_OFF		(TOSA_TC6393XB_GPIO_BASE + 6)
-#define TOSA_GPIO_CHARGE_OFF_JC		(TOSA_TC6393XB_GPIO_BASE + 7)
-#define TOSA_GPIO_BAT0_V_ON		(TOSA_TC6393XB_GPIO_BASE + 9)
-#define TOSA_GPIO_BAT1_V_ON		(TOSA_TC6393XB_GPIO_BASE + 10)
-#define TOSA_GPIO_BU_CHRG_ON		(TOSA_TC6393XB_GPIO_BASE + 11)
-#define TOSA_GPIO_BAT_SW_ON		(TOSA_TC6393XB_GPIO_BASE + 12)
-#define TOSA_GPIO_BAT0_TH_ON		(TOSA_TC6393XB_GPIO_BASE + 14)
-#define TOSA_GPIO_BAT1_TH_ON		(TOSA_TC6393XB_GPIO_BASE + 15)
-
-/*
  * PXA GPIOs
  */
 #define TOSA_GPIO_POWERON		(0)
diff --git a/arch/arm/mach-pxa/trizeps4-pcmcia.c b/arch/arm/mach-pxa/trizeps4-pcmcia.c
new file mode 100644
index 000000000000..25e363770565
--- /dev/null
+++ b/arch/arm/mach-pxa/trizeps4-pcmcia.c
@@ -0,0 +1,200 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * linux/drivers/pcmcia/pxa2xx_trizeps4.c
+ *
+ * TRIZEPS PCMCIA specific routines.
+ *
+ * Author:	Jürgen Schindele
+ * Created:	20 02, 2006
+ * Copyright:	Jürgen Schindele
+ */
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/gpio.h>
+#include <linux/interrupt.h>
+#include <linux/platform_device.h>
+
+#include <asm/mach-types.h>
+#include <asm/irq.h>
+
+#include "pxa2xx-regs.h"
+#include "trizeps4.h"
+
+#include <pcmcia/soc_common.h>
+
+extern void board_pcmcia_power(int power);
+
+static int trizeps_pcmcia_hw_init(struct soc_pcmcia_socket *skt)
+{
+	/* we dont have voltage/card/ready detection
+	 * so we dont need interrupts for it
+	 */
+	switch (skt->nr) {
+	case 0:
+		skt->stat[SOC_STAT_CD].gpio = GPIO_PCD;
+		skt->stat[SOC_STAT_CD].name = "cs0_cd";
+		skt->stat[SOC_STAT_RDY].gpio = GPIO_PRDY;
+		skt->stat[SOC_STAT_RDY].name = "cs0_rdy";
+		break;
+	default:
+		break;
+	}
+	/* release the reset of this card */
+	pr_debug("%s: sock %d irq %d\n", __func__, skt->nr, skt->socket.pci_irq);
+
+	return 0;
+}
+
+static unsigned long trizeps_pcmcia_status[2];
+
+static void trizeps_pcmcia_socket_state(struct soc_pcmcia_socket *skt,
+				struct pcmcia_state *state)
+{
+	unsigned short status = 0, change;
+	status = CFSR_readw();
+	change = (status ^ trizeps_pcmcia_status[skt->nr]) &
+				ConXS_CFSR_BVD_MASK;
+	if (change) {
+		trizeps_pcmcia_status[skt->nr] = status;
+		if (status & ConXS_CFSR_BVD1) {
+			/* enable_irq empty */
+		} else {
+			/* disable_irq empty */
+		}
+	}
+
+	switch (skt->nr) {
+	case 0:
+		/* just fill in fix states */
+		state->bvd1   = (status & ConXS_CFSR_BVD1) ? 1 : 0;
+		state->bvd2   = (status & ConXS_CFSR_BVD2) ? 1 : 0;
+		state->vs_3v  = (status & ConXS_CFSR_VS1) ? 0 : 1;
+		state->vs_Xv  = (status & ConXS_CFSR_VS2) ? 0 : 1;
+		break;
+
+#ifndef CONFIG_MACH_TRIZEPS_CONXS
+	/* on ConXS we only have one slot. Second is inactive */
+	case 1:
+		state->detect = 0;
+		state->ready  = 0;
+		state->bvd1   = 0;
+		state->bvd2   = 0;
+		state->vs_3v  = 0;
+		state->vs_Xv  = 0;
+		break;
+
+#endif
+	}
+}
+
+static int trizeps_pcmcia_configure_socket(struct soc_pcmcia_socket *skt,
+				const socket_state_t *state)
+{
+	int ret = 0;
+	unsigned short power = 0;
+
+	/* we do nothing here just check a bit */
+	switch (state->Vcc) {
+	case 0:  power &= 0xfc; break;
+	case 33: power |= ConXS_BCR_S0_VCC_3V3; break;
+	case 50:
+		pr_err("%s(): Vcc 5V not supported in socket\n", __func__);
+		break;
+	default:
+		pr_err("%s(): bad Vcc %u\n", __func__, state->Vcc);
+		ret = -1;
+	}
+
+	switch (state->Vpp) {
+	case 0:  power &= 0xf3; break;
+	case 33: power |= ConXS_BCR_S0_VPP_3V3; break;
+	case 120:
+		pr_err("%s(): Vpp 12V not supported in socket\n", __func__);
+		break;
+	default:
+		if (state->Vpp != state->Vcc) {
+			pr_err("%s(): bad Vpp %u\n", __func__, state->Vpp);
+			ret = -1;
+		}
+	}
+
+	switch (skt->nr) {
+	case 0:			 /* we only have 3.3V */
+		board_pcmcia_power(power);
+		break;
+
+#ifndef CONFIG_MACH_TRIZEPS_CONXS
+	/* on ConXS we only have one slot. Second is inactive */
+	case 1:
+#endif
+	default:
+		break;
+	}
+
+	return ret;
+}
+
+static void trizeps_pcmcia_socket_init(struct soc_pcmcia_socket *skt)
+{
+	/* default is on */
+	board_pcmcia_power(0x9);
+}
+
+static void trizeps_pcmcia_socket_suspend(struct soc_pcmcia_socket *skt)
+{
+	board_pcmcia_power(0x0);
+}
+
+static struct pcmcia_low_level trizeps_pcmcia_ops = {
+	.owner			= THIS_MODULE,
+	.hw_init		= trizeps_pcmcia_hw_init,
+	.socket_state		= trizeps_pcmcia_socket_state,
+	.configure_socket	= trizeps_pcmcia_configure_socket,
+	.socket_init		= trizeps_pcmcia_socket_init,
+	.socket_suspend		= trizeps_pcmcia_socket_suspend,
+#ifdef CONFIG_MACH_TRIZEPS_CONXS
+	.nr			= 1,
+#else
+	.nr			= 2,
+#endif
+	.first			= 0,
+};
+
+static struct platform_device *trizeps_pcmcia_device;
+
+static int __init trizeps_pcmcia_init(void)
+{
+	int ret;
+
+	if (!machine_is_trizeps4() && !machine_is_trizeps4wl())
+		return -ENODEV;
+
+	trizeps_pcmcia_device = platform_device_alloc("pxa2xx-pcmcia", -1);
+	if (!trizeps_pcmcia_device)
+		return -ENOMEM;
+
+	ret = platform_device_add_data(trizeps_pcmcia_device,
+			&trizeps_pcmcia_ops, sizeof(trizeps_pcmcia_ops));
+
+	if (ret == 0)
+		ret = platform_device_add(trizeps_pcmcia_device);
+
+	if (ret)
+		platform_device_put(trizeps_pcmcia_device);
+
+	return ret;
+}
+
+static void __exit trizeps_pcmcia_exit(void)
+{
+	platform_device_unregister(trizeps_pcmcia_device);
+}
+
+fs_initcall(trizeps_pcmcia_init);
+module_exit(trizeps_pcmcia_exit);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Juergen Schindele");
+MODULE_ALIAS("platform:pxa2xx-pcmcia");
diff --git a/arch/arm/mach-pxa/trizeps4.c b/arch/arm/mach-pxa/trizeps4.c
index f76f8be09554..716cce885379 100644
--- a/arch/arm/mach-pxa/trizeps4.c
+++ b/arch/arm/mach-pxa/trizeps4.c
@@ -40,13 +40,13 @@
 #include <asm/mach/flash.h>
 
 #include "pxa27x.h"
-#include <mach/trizeps4.h>
-#include <mach/audio.h>
+#include "trizeps4.h"
+#include <linux/platform_data/asoc-pxa.h>
 #include <linux/platform_data/video-pxafb.h>
 #include <linux/platform_data/mmc-pxamci.h>
 #include <linux/platform_data/irda-pxaficp.h>
 #include <linux/platform_data/usb-ohci-pxa27x.h>
-#include <mach/smemc.h>
+#include "smemc.h"
 
 #include "generic.h"
 #include "devices.h"
diff --git a/arch/arm/mach-pxa/include/mach/trizeps4.h b/arch/arm/mach-pxa/trizeps4.h
index 3cddb1428c5e..b6c19d155ef9 100644
--- a/arch/arm/mach-pxa/include/mach/trizeps4.h
+++ b/arch/arm/mach-pxa/trizeps4.h
@@ -11,6 +11,7 @@
 #ifndef _TRIPEPS4_H_
 #define _TRIPEPS4_H_
 
+#include "addr-map.h"
 #include "irqs.h" /* PXA_GPIO_TO_IRQ */
 
 /* physical memory regions */
diff --git a/arch/arm/mach-pxa/viper-pcmcia.c b/arch/arm/mach-pxa/viper-pcmcia.c
new file mode 100644
index 000000000000..26599dcc49b3
--- /dev/null
+++ b/arch/arm/mach-pxa/viper-pcmcia.c
@@ -0,0 +1,180 @@
+/*
+ * Viper/Zeus PCMCIA support
+ *   Copyright 2004 Arcom Control Systems
+ *
+ * Maintained by Marc Zyngier <maz@misterjones.org>
+ *
+ * Based on:
+ *   iPAQ h2200 PCMCIA support
+ *   Copyright 2004 Koen Kooi <koen@vestingbar.nl>
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file COPYING in the main directory of this archive for
+ * more details.
+ */
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/errno.h>
+#include <linux/interrupt.h>
+#include <linux/platform_device.h>
+#include <linux/gpio.h>
+
+#include <pcmcia/ss.h>
+#include <pcmcia/soc_common.h>
+
+#include <asm/irq.h>
+
+#include "viper-pcmcia.h"
+
+static struct platform_device *arcom_pcmcia_dev;
+
+static inline struct arcom_pcmcia_pdata *viper_get_pdata(void)
+{
+	return arcom_pcmcia_dev->dev.platform_data;
+}
+
+static int viper_pcmcia_hw_init(struct soc_pcmcia_socket *skt)
+{
+	struct arcom_pcmcia_pdata *pdata = viper_get_pdata();
+	unsigned long flags;
+
+	skt->stat[SOC_STAT_CD].gpio = pdata->cd_gpio;
+	skt->stat[SOC_STAT_CD].name = "PCMCIA_CD";
+	skt->stat[SOC_STAT_RDY].gpio = pdata->rdy_gpio;
+	skt->stat[SOC_STAT_RDY].name = "CF ready";
+
+	if (gpio_request(pdata->pwr_gpio, "CF power"))
+		goto err_request_pwr;
+
+	local_irq_save(flags);
+
+	if (gpio_direction_output(pdata->pwr_gpio, 0)) {
+		local_irq_restore(flags);
+		goto err_dir;
+	}
+
+	local_irq_restore(flags);
+
+	return 0;
+
+err_dir:
+	gpio_free(pdata->pwr_gpio);
+err_request_pwr:
+	dev_err(&arcom_pcmcia_dev->dev, "Failed to setup PCMCIA GPIOs\n");
+	return -1;
+}
+
+/*
+ * Release all resources.
+ */
+static void viper_pcmcia_hw_shutdown(struct soc_pcmcia_socket *skt)
+{
+	struct arcom_pcmcia_pdata *pdata = viper_get_pdata();
+
+	gpio_free(pdata->pwr_gpio);
+}
+
+static void viper_pcmcia_socket_state(struct soc_pcmcia_socket *skt,
+				      struct pcmcia_state *state)
+{
+	state->vs_3v  = 1; /* Can only apply 3.3V */
+	state->vs_Xv  = 0;
+}
+
+static int viper_pcmcia_configure_socket(struct soc_pcmcia_socket *skt,
+					 const socket_state_t *state)
+{
+	struct arcom_pcmcia_pdata *pdata = viper_get_pdata();
+
+	/* Silently ignore Vpp, output enable, speaker enable. */
+	pdata->reset(state->flags & SS_RESET);
+
+	/* Apply socket voltage */
+	switch (state->Vcc) {
+	case 0:
+		gpio_set_value(pdata->pwr_gpio, 0);
+		break;
+	case 33:
+		gpio_set_value(pdata->pwr_gpio, 1);
+		break;
+	default:
+		dev_err(&arcom_pcmcia_dev->dev, "Unsupported Vcc:%d\n", state->Vcc);
+		return -1;
+	}
+
+	return 0;
+}
+
+static struct pcmcia_low_level viper_pcmcia_ops = {
+	.owner          	= THIS_MODULE,
+	.hw_init        	= viper_pcmcia_hw_init,
+	.hw_shutdown		= viper_pcmcia_hw_shutdown,
+	.socket_state		= viper_pcmcia_socket_state,
+	.configure_socket	= viper_pcmcia_configure_socket,
+	.nr         		= 1,
+};
+
+static struct platform_device *viper_pcmcia_device;
+
+static int viper_pcmcia_probe(struct platform_device *pdev)
+{
+	int ret;
+
+	/* I can't imagine more than one device, but you never know... */
+	if (arcom_pcmcia_dev)
+		return -EEXIST;
+
+	if (!pdev->dev.platform_data)
+		return -EINVAL;
+
+	viper_pcmcia_device = platform_device_alloc("pxa2xx-pcmcia", -1);
+	if (!viper_pcmcia_device)
+		return -ENOMEM;
+
+	arcom_pcmcia_dev = pdev;
+
+	viper_pcmcia_device->dev.parent = &pdev->dev;
+
+	ret = platform_device_add_data(viper_pcmcia_device,
+				       &viper_pcmcia_ops,
+				       sizeof(viper_pcmcia_ops));
+
+	if (!ret)
+		ret = platform_device_add(viper_pcmcia_device);
+
+	if (ret) {
+		platform_device_put(viper_pcmcia_device);
+		arcom_pcmcia_dev = NULL;
+	}
+
+	return ret;
+}
+
+static int viper_pcmcia_remove(struct platform_device *pdev)
+{
+	platform_device_unregister(viper_pcmcia_device);
+	arcom_pcmcia_dev = NULL;
+	return 0;
+}
+
+static struct platform_device_id viper_pcmcia_id_table[] = {
+	{ .name = "viper-pcmcia", },
+	{ .name = "zeus-pcmcia",  },
+	{ },
+};
+
+static struct platform_driver viper_pcmcia_driver = {
+	.probe		= viper_pcmcia_probe,
+	.remove		= viper_pcmcia_remove,
+	.driver		= {
+		.name	= "arcom-pcmcia",
+	},
+	.id_table	= viper_pcmcia_id_table,
+};
+
+module_platform_driver(viper_pcmcia_driver);
+
+MODULE_DEVICE_TABLE(platform, viper_pcmcia_id_table);
+MODULE_LICENSE("GPL");
diff --git a/include/linux/platform_data/pcmcia-pxa2xx_viper.h b/arch/arm/mach-pxa/viper-pcmcia.h
index a23b58aff9e1..a23b58aff9e1 100644
--- a/include/linux/platform_data/pcmcia-pxa2xx_viper.h
+++ b/arch/arm/mach-pxa/viper-pcmcia.h
diff --git a/arch/arm/mach-pxa/viper.c b/arch/arm/mach-pxa/viper.c
index 3aa34e9a15d3..5b43351ee840 100644
--- a/arch/arm/mach-pxa/viper.c
+++ b/arch/arm/mach-pxa/viper.c
@@ -46,10 +46,10 @@
 #include <linux/syscore_ops.h>
 
 #include "pxa25x.h"
-#include <mach/audio.h>
+#include <linux/platform_data/asoc-pxa.h>
 #include <linux/platform_data/video-pxafb.h>
-#include <mach/regs-uart.h>
-#include <linux/platform_data/pcmcia-pxa2xx_viper.h>
+#include "regs-uart.h"
+#include "viper-pcmcia.h"
 #include "viper.h"
 
 #include <asm/setup.h>
@@ -851,7 +851,7 @@ static void __init viper_init_vcore_gpios(void)
 		goto err_dir;
 
 	/* c/should assume redboot set the correct level ??? */
-	viper_set_core_cpu_voltage(get_clk_frequency_khz(0), 1);
+	viper_set_core_cpu_voltage(pxa25x_get_clk_frequency_khz(0), 1);
 
 	return;
 
@@ -998,6 +998,18 @@ static struct map_desc viper_io_desc[] __initdata = {
 		.length  = 0x00800000,
 		.type    = MT_DEVICE,
 	},
+	{
+		/*
+		 * ISA I/O space mapping:
+		 * -  ports 0x0000-0x0fff are PC/104
+		 * -  ports 0x10000-0x10fff are PCMCIA slot 1
+		 * -  ports 0x11000-0x11fff are PC/104
+		 */
+		.virtual = PCI_IO_VIRT_BASE,
+		.pfn     = __phys_to_pfn(0x30000000),
+		.length  = 0x1000,
+		.type    = MT_DEVICE,
+	},
 };
 
 static void __init viper_map_io(void)
diff --git a/arch/arm/mach-pxa/vpac270-pcmcia.c b/arch/arm/mach-pxa/vpac270-pcmcia.c
new file mode 100644
index 000000000000..9fd990c8a5fb
--- /dev/null
+++ b/arch/arm/mach-pxa/vpac270-pcmcia.c
@@ -0,0 +1,137 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * linux/drivers/pcmcia/pxa2xx_vpac270.c
+ *
+ * Driver for Voipac PXA270 PCMCIA and CF sockets
+ *
+ * Copyright (C) 2010-2011 Marek Vasut <marek.vasut@gmail.com>
+ */
+
+#include <linux/gpio.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+
+#include <asm/mach-types.h>
+
+#include "vpac270.h"
+
+#include <pcmcia/soc_common.h>
+
+static struct gpio vpac270_pcmcia_gpios[] = {
+	{ GPIO107_VPAC270_PCMCIA_PPEN,	GPIOF_INIT_LOW,	"PCMCIA PPEN" },
+	{ GPIO11_VPAC270_PCMCIA_RESET,	GPIOF_INIT_LOW,	"PCMCIA Reset" },
+};
+
+static struct gpio vpac270_cf_gpios[] = {
+	{ GPIO16_VPAC270_CF_RESET,	GPIOF_INIT_LOW,	"CF Reset" },
+};
+
+static int vpac270_pcmcia_hw_init(struct soc_pcmcia_socket *skt)
+{
+	int ret;
+
+	if (skt->nr == 0) {
+		ret = gpio_request_array(vpac270_pcmcia_gpios,
+				ARRAY_SIZE(vpac270_pcmcia_gpios));
+
+		skt->stat[SOC_STAT_CD].gpio = GPIO84_VPAC270_PCMCIA_CD;
+		skt->stat[SOC_STAT_CD].name = "PCMCIA CD";
+		skt->stat[SOC_STAT_RDY].gpio = GPIO35_VPAC270_PCMCIA_RDY;
+		skt->stat[SOC_STAT_RDY].name = "PCMCIA Ready";
+	} else {
+		ret = gpio_request_array(vpac270_cf_gpios,
+				ARRAY_SIZE(vpac270_cf_gpios));
+
+		skt->stat[SOC_STAT_CD].gpio = GPIO17_VPAC270_CF_CD;
+		skt->stat[SOC_STAT_CD].name = "CF CD";
+		skt->stat[SOC_STAT_RDY].gpio = GPIO12_VPAC270_CF_RDY;
+		skt->stat[SOC_STAT_RDY].name = "CF Ready";
+	}
+
+	return ret;
+}
+
+static void vpac270_pcmcia_hw_shutdown(struct soc_pcmcia_socket *skt)
+{
+	if (skt->nr == 0)
+		gpio_free_array(vpac270_pcmcia_gpios,
+					ARRAY_SIZE(vpac270_pcmcia_gpios));
+	else
+		gpio_free_array(vpac270_cf_gpios,
+					ARRAY_SIZE(vpac270_cf_gpios));
+}
+
+static void vpac270_pcmcia_socket_state(struct soc_pcmcia_socket *skt,
+					struct pcmcia_state *state)
+{
+	state->vs_3v  = 1;
+	state->vs_Xv  = 0;
+}
+
+static int
+vpac270_pcmcia_configure_socket(struct soc_pcmcia_socket *skt,
+				const socket_state_t *state)
+{
+	if (skt->nr == 0) {
+		gpio_set_value(GPIO11_VPAC270_PCMCIA_RESET,
+			(state->flags & SS_RESET));
+		gpio_set_value(GPIO107_VPAC270_PCMCIA_PPEN,
+			!(state->Vcc == 33 || state->Vcc == 50));
+	} else {
+		gpio_set_value(GPIO16_VPAC270_CF_RESET,
+			(state->flags & SS_RESET));
+	}
+
+	return 0;
+}
+
+static struct pcmcia_low_level vpac270_pcmcia_ops = {
+	.owner			= THIS_MODULE,
+
+	.first			= 0,
+	.nr			= 2,
+
+	.hw_init		= vpac270_pcmcia_hw_init,
+	.hw_shutdown		= vpac270_pcmcia_hw_shutdown,
+
+	.socket_state		= vpac270_pcmcia_socket_state,
+	.configure_socket	= vpac270_pcmcia_configure_socket,
+};
+
+static struct platform_device *vpac270_pcmcia_device;
+
+static int __init vpac270_pcmcia_init(void)
+{
+	int ret;
+
+	if (!machine_is_vpac270())
+		return -ENODEV;
+
+	vpac270_pcmcia_device = platform_device_alloc("pxa2xx-pcmcia", -1);
+	if (!vpac270_pcmcia_device)
+		return -ENOMEM;
+
+	ret = platform_device_add_data(vpac270_pcmcia_device,
+		&vpac270_pcmcia_ops, sizeof(vpac270_pcmcia_ops));
+
+	if (!ret)
+		ret = platform_device_add(vpac270_pcmcia_device);
+
+	if (ret)
+		platform_device_put(vpac270_pcmcia_device);
+
+	return ret;
+}
+
+static void __exit vpac270_pcmcia_exit(void)
+{
+	platform_device_unregister(vpac270_pcmcia_device);
+}
+
+module_init(vpac270_pcmcia_init);
+module_exit(vpac270_pcmcia_exit);
+
+MODULE_AUTHOR("Marek Vasut <marek.vasut@gmail.com>");
+MODULE_DESCRIPTION("PCMCIA support for Voipac PXA270");
+MODULE_ALIAS("platform:pxa2xx-pcmcia");
+MODULE_LICENSE("GPL");
diff --git a/arch/arm/mach-pxa/vpac270.c b/arch/arm/mach-pxa/vpac270.c
index 14505e83479e..8f74bafcf1f9 100644
--- a/arch/arm/mach-pxa/vpac270.c
+++ b/arch/arm/mach-pxa/vpac270.c
@@ -29,8 +29,8 @@
 #include <asm/mach/arch.h>
 
 #include "pxa27x.h"
-#include <mach/audio.h>
-#include <mach/vpac270.h>
+#include <linux/platform_data/asoc-pxa.h>
+#include "vpac270.h"
 #include <linux/platform_data/mmc-pxamci.h>
 #include <linux/platform_data/video-pxafb.h>
 #include <linux/platform_data/usb-ohci-pxa27x.h>
diff --git a/arch/arm/mach-pxa/include/mach/vpac270.h b/arch/arm/mach-pxa/vpac270.h
index 0cd094d8c553..0cd094d8c553 100644
--- a/arch/arm/mach-pxa/include/mach/vpac270.h
+++ b/arch/arm/mach-pxa/vpac270.h
diff --git a/arch/arm/mach-pxa/xcep.c b/arch/arm/mach-pxa/xcep.c
index f485146b899f..6bb02b65fb82 100644
--- a/arch/arm/mach-pxa/xcep.c
+++ b/arch/arm/mach-pxa/xcep.c
@@ -24,9 +24,9 @@
 #include <asm/mach/irq.h>
 #include <asm/mach/map.h>
 
-#include <mach/hardware.h>
 #include "pxa25x.h"
-#include <mach/smemc.h>
+#include "addr-map.h"
+#include "smemc.h"
 
 #include "generic.h"
 #include "devices.h"
diff --git a/arch/arm/mach-pxa/z2.c b/arch/arm/mach-pxa/z2.c
index 8e74fbb0a96e..c4d4162a7e6e 100644
--- a/arch/arm/mach-pxa/z2.c
+++ b/arch/arm/mach-pxa/z2.c
@@ -34,7 +34,7 @@
 
 #include "pxa27x.h"
 #include "mfp-pxa27x.h"
-#include <mach/z2.h>
+#include "z2.h"
 #include <linux/platform_data/video-pxafb.h>
 #include <linux/platform_data/mmc-pxamci.h>
 #include <linux/platform_data/keypad-pxa27x.h>
@@ -570,7 +570,6 @@ static struct pxa2xx_spi_chip z2_lbs_chip_info = {
 	.rx_threshold	= 8,
 	.tx_threshold	= 8,
 	.timeout	= 1000,
-	.gpio_cs	= GPIO24_ZIPITZ2_WIFI_CS,
 };
 
 static struct libertas_spi_platform_data z2_lbs_pdata = {
@@ -584,7 +583,6 @@ static struct pxa2xx_spi_chip lms283_chip_info = {
 	.rx_threshold	= 1,
 	.tx_threshold	= 1,
 	.timeout	= 64,
-	.gpio_cs	= GPIO88_ZIPITZ2_LCD_CS,
 };
 
 static struct gpiod_lookup_table lms283_gpio_table = {
@@ -624,8 +622,26 @@ static struct pxa2xx_spi_controller pxa_ssp2_master_info = {
 	.num_chipselect	= 1,
 };
 
+static struct gpiod_lookup_table pxa_ssp1_gpio_table = {
+	.dev_id = "spi1",
+	.table = {
+		GPIO_LOOKUP_IDX("gpio-pxa", GPIO24_ZIPITZ2_WIFI_CS, "cs", 0, GPIO_ACTIVE_LOW),
+		{ },
+	},
+};
+
+static struct gpiod_lookup_table pxa_ssp2_gpio_table = {
+	.dev_id = "spi2",
+	.table = {
+		GPIO_LOOKUP_IDX("gpio-pxa", GPIO88_ZIPITZ2_LCD_CS, "cs", 0, GPIO_ACTIVE_LOW),
+		{ },
+	},
+};
+
 static void __init z2_spi_init(void)
 {
+	gpiod_add_lookup_table(&pxa_ssp1_gpio_table);
+	gpiod_add_lookup_table(&pxa_ssp2_gpio_table);
 	pxa2xx_set_spi_info(1, &pxa_ssp1_master_info);
 	pxa2xx_set_spi_info(2, &pxa_ssp2_master_info);
 	gpiod_add_lookup_table(&lms283_gpio_table);
@@ -635,6 +651,15 @@ static void __init z2_spi_init(void)
 static inline void z2_spi_init(void) {}
 #endif
 
+static struct gpiod_lookup_table z2_audio_gpio_table = {
+	.dev_id = "soc-audio",
+	.table = {
+		GPIO_LOOKUP("gpio-pxa", GPIO37_ZIPITZ2_HEADSET_DETECT,
+			    "hsdet-gpio", GPIO_ACTIVE_HIGH),
+		{ },
+	},
+};
+
 /******************************************************************************
  * Core power regulator
  ******************************************************************************/
@@ -739,6 +764,8 @@ static void __init z2_init(void)
 	z2_keys_init();
 	z2_pmic_init();
 
+	gpiod_add_lookup_table(&z2_audio_gpio_table);
+
 	pm_power_off = z2_power_off;
 }
 
diff --git a/arch/arm/mach-pxa/include/mach/z2.h b/arch/arm/mach-pxa/z2.h
index a78b2e28b1db..a78b2e28b1db 100644
--- a/arch/arm/mach-pxa/include/mach/z2.h
+++ b/arch/arm/mach-pxa/z2.h
diff --git a/arch/arm/mach-pxa/zeus.c b/arch/arm/mach-pxa/zeus.c
index 97700429633e..ff0d8bb9f557 100644
--- a/arch/arm/mach-pxa/zeus.c
+++ b/arch/arm/mach-pxa/zeus.c
@@ -39,17 +39,17 @@
 
 #include "pxa27x.h"
 #include "devices.h"
-#include <mach/regs-uart.h>
+#include "regs-uart.h"
 #include <linux/platform_data/usb-ohci-pxa27x.h>
 #include <linux/platform_data/mmc-pxamci.h>
 #include "pxa27x-udc.h"
 #include "udc.h"
 #include <linux/platform_data/video-pxafb.h>
 #include "pm.h"
-#include <mach/audio.h>
-#include <linux/platform_data/pcmcia-pxa2xx_viper.h>
+#include <linux/platform_data/asoc-pxa.h>
+#include "viper-pcmcia.h"
 #include "zeus.h"
-#include <mach/smemc.h>
+#include "smemc.h"
 
 #include "generic.h"
 
@@ -929,6 +929,18 @@ static struct map_desc zeus_io_desc[] __initdata = {
 		.length  = 0x00800000,
 		.type    = MT_DEVICE,
 	},
+	{
+		/*
+		 * ISA I/O space mapping:
+		 * -  ports 0x0000-0x0fff are PC/104
+		 * -  ports 0x10000-0x10fff are PCMCIA slot 1
+		 * -  ports 0x11000-0x11fff are PC/104
+		 */
+		.virtual = PCI_IO_VIRT_BASE,
+		.pfn     = __phys_to_pfn(ZEUS_PC104IO_PHYS),
+		.length  = 0x1000,
+		.type    = MT_DEVICE,
+	},
 };
 
 static void __init zeus_map_io(void)
diff --git a/arch/arm/mach-pxa/zylonite.c b/arch/arm/mach-pxa/zylonite.c
index 79f0025fa17a..8ed75ac29b1a 100644
--- a/arch/arm/mach-pxa/zylonite.c
+++ b/arch/arm/mach-pxa/zylonite.c
@@ -20,17 +20,19 @@
 #include <linux/pwm.h>
 #include <linux/pwm_backlight.h>
 #include <linux/smc91x.h>
+#include <linux/soc/pxa/cpu.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
 #include "pxa3xx.h"
-#include <mach/audio.h>
+#include <linux/platform_data/asoc-pxa.h>
 #include <linux/platform_data/video-pxafb.h>
 #include "zylonite.h"
 #include <linux/platform_data/mmc-pxamci.h>
 #include <linux/platform_data/usb-ohci-pxa27x.h>
 #include <linux/platform_data/keypad-pxa27x.h>
 #include <linux/platform_data/mtd-nand-pxa3xx.h>
+#include "mfp.h"
 
 #include "devices.h"
 #include "generic.h"
@@ -424,6 +426,35 @@ static void __init zylonite_init_ohci(void)
 static inline void zylonite_init_ohci(void) {}
 #endif /* CONFIG_USB_OHCI_HCD || CONFIG_USB_OHCI_HCD_MODULE */
 
+static struct gpiod_lookup_table zylonite_wm97xx_touch_gpio15_table = {
+	.dev_id = "wm97xx-touch.0",
+	.table = {
+		GPIO_LOOKUP("gpio-pxa", mfp_to_gpio(MFP_PIN_GPIO15),
+			    "touch", GPIO_ACTIVE_LOW),
+		{ },
+	},
+};
+
+static struct gpiod_lookup_table zylonite_wm97xx_touch_gpio26_table = {
+	.dev_id = "wm97xx-touch.0",
+	.table = {
+		GPIO_LOOKUP("gpio-pxa", mfp_to_gpio(MFP_PIN_GPIO26),
+			    "touch", GPIO_ACTIVE_LOW),
+		{ },
+	},
+};
+
+static void __init zylonite_init_wm97xx_touch(void)
+{
+	if (!IS_ENABLED(CONFIG_TOUCHSCREEN_WM97XX_ZYLONITE))
+		return;
+
+	if (cpu_is_pxa320())
+		gpiod_add_lookup_table(&zylonite_wm97xx_touch_gpio15_table);
+	else
+		gpiod_add_lookup_table(&zylonite_wm97xx_touch_gpio26_table);
+}
+
 static void __init zylonite_init(void)
 {
 	pxa_set_ffuart_info(NULL);
@@ -449,6 +480,7 @@ static void __init zylonite_init(void)
 	zylonite_init_nand();
 	zylonite_init_leds();
 	zylonite_init_ohci();
+	zylonite_init_wm97xx_touch();
 }
 
 MACHINE_START(ZYLONITE, "PXA3xx Platform Development Kit (aka Zylonite)")
diff --git a/arch/arm/mach-pxa/zylonite.h b/arch/arm/mach-pxa/zylonite.h
index 7300ec2aac0d..afe3efcb8e04 100644
--- a/arch/arm/mach-pxa/zylonite.h
+++ b/arch/arm/mach-pxa/zylonite.h
@@ -2,6 +2,8 @@
 #ifndef __ASM_ARCH_ZYLONITE_H
 #define __ASM_ARCH_ZYLONITE_H
 
+#include <linux/soc/pxa/cpu.h>
+
 #define ZYLONITE_ETH_PHYS	0x14000000
 
 #define EXT_GPIO(x)		(128 + (x))
diff --git a/arch/arm/mach-pxa/zylonite_pxa300.c b/arch/arm/mach-pxa/zylonite_pxa300.c
index 956fec1c4940..50a8a3547dbc 100644
--- a/arch/arm/mach-pxa/zylonite_pxa300.c
+++ b/arch/arm/mach-pxa/zylonite_pxa300.c
@@ -17,6 +17,7 @@
 #include <linux/platform_data/i2c-pxa.h>
 #include <linux/platform_data/pca953x.h>
 #include <linux/gpio.h>
+#include <linux/soc/pxa/cpu.h>
 
 #include "pxa300.h"
 #include "devices.h"
diff --git a/arch/arm/mach-pxa/zylonite_pxa320.c b/arch/arm/mach-pxa/zylonite_pxa320.c
index 94cb834f36cd..67cab4f1194b 100644
--- a/arch/arm/mach-pxa/zylonite_pxa320.c
+++ b/arch/arm/mach-pxa/zylonite_pxa320.c
@@ -14,6 +14,7 @@
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/gpio.h>
+#include <linux/soc/pxa/cpu.h>
 
 #include "pxa320.h"
 #include "zylonite.h"
diff --git a/arch/arm/mach-qcom/Kconfig b/arch/arm/mach-qcom/Kconfig
index 466acc4a5e0c..12a812e61c16 100644
--- a/arch/arm/mach-qcom/Kconfig
+++ b/arch/arm/mach-qcom/Kconfig
@@ -2,7 +2,6 @@
 menuconfig ARCH_QCOM
 	bool "Qualcomm Support"
 	depends on ARCH_MULTI_V7
-	select ARCH_SUPPORTS_BIG_ENDIAN
 	select ARM_GIC
 	select ARM_AMBA
 	select PINCTRL
@@ -21,6 +20,10 @@ config ARCH_MSM8X60
 	bool "Enable support for MSM8X60"
 	select CLKSRC_QCOM
 
+config ARCH_MSM8909
+	bool "Enable support for MSM8909"
+	select HAVE_ARM_ARCH_TIMER
+
 config ARCH_MSM8916
 	bool "Enable support for MSM8916"
 	select HAVE_ARM_ARCH_TIMER
diff --git a/arch/arm/mach-qcom/platsmp.c b/arch/arm/mach-qcom/platsmp.c
index 58a4228455ce..5d2f386a46d8 100644
--- a/arch/arm/mach-qcom/platsmp.c
+++ b/arch/arm/mach-qcom/platsmp.c
@@ -357,8 +357,7 @@ static void __init qcom_smp_prepare_cpus(unsigned int max_cpus)
 {
 	int cpu;
 
-	if (qcom_scm_set_cold_boot_addr(secondary_startup_arm,
-					cpu_present_mask)) {
+	if (qcom_scm_set_cold_boot_addr(secondary_startup_arm)) {
 		for_each_present_cpu(cpu) {
 			if (cpu == smp_processor_id())
 				continue;
@@ -385,6 +384,7 @@ static const struct smp_operations qcom_smp_cortex_a7_ops __initconst = {
 #endif
 };
 CPU_METHOD_OF_DECLARE(qcom_smp_msm8226, "qcom,msm8226-smp", &qcom_smp_cortex_a7_ops);
+CPU_METHOD_OF_DECLARE(qcom_smp_msm8909, "qcom,msm8909-smp", &qcom_smp_cortex_a7_ops);
 CPU_METHOD_OF_DECLARE(qcom_smp_msm8916, "qcom,msm8916-smp", &qcom_smp_cortex_a7_ops);
 
 static const struct smp_operations qcom_smp_kpssv1_ops __initconst = {
diff --git a/arch/arm/mach-realview/Kconfig b/arch/arm/mach-realview/Kconfig
deleted file mode 100644
index a4c36024b5e8..000000000000
--- a/arch/arm/mach-realview/Kconfig
+++ /dev/null
@@ -1,103 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0-only
-menuconfig ARCH_REALVIEW
-	bool "ARM Ltd. RealView family"
-	depends on ARCH_MULTI_V5 || ARCH_MULTI_V6 || ARCH_MULTI_V7
-	select ARM_AMBA
-	select ARM_GIC
-	select ARM_TIMER_SP804
-	select CLK_SP810
-	select GPIO_PL061 if GPIOLIB
-	select HAVE_ARM_SCU if SMP
-	select HAVE_ARM_TWD if SMP
-	select HAVE_PATA_PLATFORM
-	select HAVE_TCM
-	select CLK_ICST
-	select MACH_REALVIEW_EB if ARCH_MULTI_V5
-	select MFD_SYSCON
-	select PLAT_VERSATILE
-	select POWER_RESET
-	select POWER_RESET_VERSATILE
-	select POWER_SUPPLY
-	select SOC_REALVIEW
-	help
-	  This enables support for ARM Ltd RealView boards.
-
-if ARCH_REALVIEW
-
-config MACH_REALVIEW_EB
-	bool "Support RealView(R) Emulation Baseboard"
-	select ARM_GIC
-	select CPU_ARM926T if ARCH_MULTI_V5
-	help
-	  Include support for the ARM(R) RealView(R) Emulation Baseboard
-	  platform. On an ARMv5 kernel, this will include support for
-	  the ARM926EJ-S core tile, while on an ARMv6/v7 kernel, at least
-	  one of the ARM1136, ARM1176, ARM11MPCore or Cortex-A9MPCore
-	  core tile options should be enabled.
-
-config REALVIEW_EB_ARM1136
-	bool "Support ARM1136J(F)-S Tile"
-	depends on MACH_REALVIEW_EB && ARCH_MULTI_V6
-	select CPU_V6
-	help
-	  Enable support for the ARM1136 tile fitted to the
-	  Realview(R) Emulation Baseboard platform.
-
-config REALVIEW_EB_ARM1176
-	bool "Support ARM1176JZ(F)-S Tile"
-	depends on MACH_REALVIEW_EB && ARCH_MULTI_V6
-	help
-	  Enable support for the ARM1176 tile fitted to the
-	  Realview(R) Emulation Baseboard platform.
-
-config REALVIEW_EB_A9MP
-	bool "Support Multicore Cortex-A9 Tile"
-	depends on MACH_REALVIEW_EB && ARCH_MULTI_V7
-	help
-	  Enable support for the Cortex-A9MPCore tile fitted to the
-	  Realview(R) Emulation Baseboard platform.
-
-config REALVIEW_EB_ARM11MP
-	bool "Support ARM11MPCore Tile"
-	depends on MACH_REALVIEW_EB && ARCH_MULTI_V6
-	select HAVE_SMP
-	help
-	  Enable support for the ARM11MPCore tile fitted to the Realview(R)
-	  Emulation Baseboard platform.
-
-config MACH_REALVIEW_PB11MP
-	bool "Support RealView(R) Platform Baseboard for ARM11MPCore"
-	depends on ARCH_MULTI_V6
-	select HAVE_SMP
-	help
-	  Include support for the ARM(R) RealView(R) Platform Baseboard for
-	  the ARM11MPCore.  This platform has an on-board ARM11MPCore and has
-	  support for PCI-E and Compact Flash.
-
-# ARMv6 CPU without K extensions, but does have the new exclusive ops
-config MACH_REALVIEW_PB1176
-	bool "Support RealView(R) Platform Baseboard for ARM1176JZF-S"
-	depends on ARCH_MULTI_V6
-	select CPU_V6
-	select HAVE_TCM
-	help
-	  Include support for the ARM(R) RealView(R) Platform Baseboard for
-	  ARM1176JZF-S.
-
-config MACH_REALVIEW_PBA8
-	bool "Support RealView(R) Platform Baseboard for Cortex(tm)-A8 platform"
-	depends on ARCH_MULTI_V7
-	help
-	  Include support for the ARM(R) RealView Platform Baseboard for
-	  Cortex(tm)-A8.  This platform has an on-board Cortex-A8 and has
-	  support for PCI-E and Compact Flash.
-
-config MACH_REALVIEW_PBX
-	bool "Support RealView(R) Platform Baseboard Explore for Cortex-A9"
-	depends on ARCH_MULTI_V7
-	select ZONE_DMA
-	help
-	  Include support for the ARM(R) RealView(R) Platform Baseboard
-	  Explore.
-
-endif
diff --git a/arch/arm/mach-realview/Makefile b/arch/arm/mach-realview/Makefile
deleted file mode 100644
index e259091591b8..000000000000
--- a/arch/arm/mach-realview/Makefile
+++ /dev/null
@@ -1,8 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0-only
-#
-# Makefile for the linux kernel.
-#
-ccflags-$(CONFIG_ARCH_MULTIPLATFORM) := -I$(srctree)/arch/arm/plat-versatile/include
-
-obj-y					+= realview-dt.o
-obj-$(CONFIG_SMP)			+= platsmp-dt.o
diff --git a/arch/arm/mach-realview/platsmp-dt.c b/arch/arm/mach-realview/platsmp-dt.c
deleted file mode 100644
index 5ae783767a5d..000000000000
--- a/arch/arm/mach-realview/platsmp-dt.c
+++ /dev/null
@@ -1,93 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (C) 2015 Linus Walleij
- */
-#include <linux/smp.h>
-#include <linux/io.h>
-#include <linux/of.h>
-#include <linux/of_address.h>
-#include <linux/regmap.h>
-#include <linux/mfd/syscon.h>
-
-#include <asm/cacheflush.h>
-#include <asm/smp_plat.h>
-#include <asm/smp_scu.h>
-
-#include <plat/platsmp.h>
-
-#define REALVIEW_SYS_FLAGSSET_OFFSET	0x30
-
-static const struct of_device_id realview_scu_match[] = {
-	{ .compatible = "arm,arm11mp-scu", },
-	{ .compatible = "arm,cortex-a9-scu", },
-	{ .compatible = "arm,cortex-a5-scu", },
-	{ }
-};
-
-static const struct of_device_id realview_syscon_match[] = {
-        { .compatible = "arm,core-module-integrator", },
-        { .compatible = "arm,realview-eb-syscon", },
-        { .compatible = "arm,realview-pb11mp-syscon", },
-        { .compatible = "arm,realview-pbx-syscon", },
-        { },
-};
-
-static void __init realview_smp_prepare_cpus(unsigned int max_cpus)
-{
-	struct device_node *np;
-	void __iomem *scu_base;
-	struct regmap *map;
-	unsigned int ncores;
-	int i;
-
-	np = of_find_matching_node(NULL, realview_scu_match);
-	if (!np) {
-		pr_err("PLATSMP: No SCU base address\n");
-		return;
-	}
-	scu_base = of_iomap(np, 0);
-	of_node_put(np);
-	if (!scu_base) {
-		pr_err("PLATSMP: No SCU remap\n");
-		return;
-	}
-
-	scu_enable(scu_base);
-	ncores = scu_get_core_count(scu_base);
-	pr_info("SCU: %d cores detected\n", ncores);
-	for (i = 0; i < ncores; i++)
-		set_cpu_possible(i, true);
-	iounmap(scu_base);
-
-	/* The syscon contains the magic SMP start address registers */
-	np = of_find_matching_node(NULL, realview_syscon_match);
-	if (!np) {
-		pr_err("PLATSMP: No syscon match\n");
-		return;
-	}
-	map = syscon_node_to_regmap(np);
-	if (IS_ERR(map)) {
-		pr_err("PLATSMP: No syscon regmap\n");
-		return;
-	}
-	/* Put the boot address in this magic register */
-	regmap_write(map, REALVIEW_SYS_FLAGSSET_OFFSET,
-		     __pa_symbol(versatile_secondary_startup));
-}
-
-#ifdef CONFIG_HOTPLUG_CPU
-static void realview_cpu_die(unsigned int cpu)
-{
-	return versatile_immitation_cpu_die(cpu, 0x20);
-}
-#endif
-
-static const struct smp_operations realview_dt_smp_ops __initconst = {
-	.smp_prepare_cpus	= realview_smp_prepare_cpus,
-	.smp_secondary_init	= versatile_secondary_init,
-	.smp_boot_secondary	= versatile_boot_secondary,
-#ifdef CONFIG_HOTPLUG_CPU
-	.cpu_die		= realview_cpu_die,
-#endif
-};
-CPU_METHOD_OF_DECLARE(realview_smp, "arm,realview-smp", &realview_dt_smp_ops);
diff --git a/arch/arm/mach-rockchip/platsmp.c b/arch/arm/mach-rockchip/platsmp.c
index d60856898d97..36915a073c23 100644
--- a/arch/arm/mach-rockchip/platsmp.c
+++ b/arch/arm/mach-rockchip/platsmp.c
@@ -137,7 +137,7 @@ static int rockchip_boot_secondary(unsigned int cpu, struct task_struct *idle)
 		/*
 		 * We communicate with the bootrom to active the cpus other
 		 * than cpu0, after a blob of initialize code, they will
-		 * stay at wfe state, once they are actived, they will check
+		 * stay at wfe state, once they are activated, they will check
 		 * the mailbox:
 		 * sram_base_addr + 4: 0xdeadbeaf
 		 * sram_base_addr + 8: start address for pc
@@ -189,7 +189,7 @@ static int __init rockchip_smp_prepare_sram(struct device_node *node)
 	rockchip_boot_fn = __pa_symbol(secondary_startup);
 
 	/* copy the trampoline to sram, that runs during startup of the core */
-	memcpy(sram_base_addr, &rockchip_secondary_trampoline, trampoline_sz);
+	memcpy_toio(sram_base_addr, &rockchip_secondary_trampoline, trampoline_sz);
 	flush_cache_all();
 	outer_clean_range(0, trampoline_sz);
 
diff --git a/arch/arm/mach-rockchip/pm.c b/arch/arm/mach-rockchip/pm.c
index 87389d9456b9..30d781d80fe0 100644
--- a/arch/arm/mach-rockchip/pm.c
+++ b/arch/arm/mach-rockchip/pm.c
@@ -311,7 +311,7 @@ void __init rockchip_suspend_init(void)
 					     &match);
 	if (!match) {
 		pr_err("Failed to find PMU node\n");
-		return;
+		goto out_put;
 	}
 	pm_data = (struct rockchip_pm_data *) match->data;
 
@@ -320,9 +320,12 @@ void __init rockchip_suspend_init(void)
 
 		if (ret) {
 			pr_err("%s: matches init error %d\n", __func__, ret);
-			return;
+			goto out_put;
 		}
 	}
 
 	suspend_set_ops(pm_data->ops);
+
+out_put:
+	of_node_put(np);
 }
diff --git a/arch/arm/mach-rpc/Kconfig b/arch/arm/mach-rpc/Kconfig
new file mode 100644
index 000000000000..55f6d829b677
--- /dev/null
+++ b/arch/arm/mach-rpc/Kconfig
@@ -0,0 +1,21 @@
+config ARCH_RPC
+	bool "RiscPC"
+	depends on ARCH_MULTI_V4 && !(ARCH_MULTI_V4T || ARCH_MULTI_V5)
+	depends on !(ARCH_FOOTBRIDGE || ARCH_SA1100 || ARCH_MOXART || ARCH_GEMINI)
+	depends on !CC_IS_CLANG && GCC_VERSION < 90100 && GCC_VERSION >= 60000
+	depends on CPU_LITTLE_ENDIAN
+	depends on ATAGS
+	depends on MMU
+	select ARCH_ACORN
+	select ARCH_MAY_HAVE_PC_FDC
+	select CPU_SA110
+	select FIQ
+	select HAVE_PATA_PLATFORM
+	select ISA_DMA_API
+	select LEGACY_TIMER_TICK
+	select NEED_MACH_IO_H
+	select NEED_MACH_MEMORY_H
+	select NO_IOPORT_MAP
+	help
+	  On the Acorn Risc-PC, Linux can support the internal IDE disk and
+	  CD-ROM interface, serial and parallel port, and the floppy drive.
diff --git a/arch/arm/mach-rpc/Makefile.boot b/arch/arm/mach-rpc/Makefile.boot
deleted file mode 100644
index 0ed8e8fbde99..000000000000
--- a/arch/arm/mach-rpc/Makefile.boot
+++ /dev/null
@@ -1,5 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0-only
-   zreladdr-y	+= 0x10008000
-params_phys-y	:= 0x10000100
-initrd_phys-y	:= 0x18000000
-
diff --git a/arch/arm/mach-rpc/fiq.S b/arch/arm/mach-rpc/fiq.S
index 0de83e9b0b39..087bdf4bc093 100644
--- a/arch/arm/mach-rpc/fiq.S
+++ b/arch/arm/mach-rpc/fiq.S
@@ -2,10 +2,11 @@
 #include <linux/linkage.h>
 #include <asm/assembler.h>
 #include <mach/hardware.h>
-#include <mach/entry-macro.S>
 
-	.text
+	.equ	ioc_base_high, IOC_BASE & 0xff000000
+	.equ	ioc_base_low, IOC_BASE & 0x00ff0000
 
+	.text
 	.global	rpc_default_fiq_end
 ENTRY(rpc_default_fiq_start)
 	mov	r12, #ioc_base_high
diff --git a/arch/arm/mach-rpc/include/mach/entry-macro.S b/arch/arm/mach-rpc/include/mach/entry-macro.S
deleted file mode 100644
index a6d1a9f4bb79..000000000000
--- a/arch/arm/mach-rpc/include/mach/entry-macro.S
+++ /dev/null
@@ -1,13 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-#include <mach/hardware.h>
-#include <asm/hardware/entry-macro-iomd.S>
-
-	.equ	ioc_base_high, IOC_BASE & 0xff000000
-	.equ	ioc_base_low, IOC_BASE & 0x00ff0000
-
-	.macro  get_irqnr_preamble, base, tmp
-	mov	\base, #ioc_base_high		@ point at IOC
-	.if	ioc_base_low
-	orr	\base, \base, #ioc_base_low
-	.endif
-	.endm
diff --git a/arch/arm/mach-rpc/irq.c b/arch/arm/mach-rpc/irq.c
index 803aeb126f0e..dc29384b6ef8 100644
--- a/arch/arm/mach-rpc/irq.c
+++ b/arch/arm/mach-rpc/irq.c
@@ -14,6 +14,99 @@
 #define CLR	0x04
 #define MASK	0x08
 
+static const u8 irq_prio_h[256] = {
+	 0, 8, 9, 8,10,10,10,10,11,11,11,11,10,10,10,10,
+	12, 8, 9, 8,10,10,10,10,11,11,11,11,10,10,10,10,
+	13,13,13,13,10,10,10,10,11,11,11,11,10,10,10,10,
+	13,13,13,13,10,10,10,10,11,11,11,11,10,10,10,10,
+	14,14,14,14,10,10,10,10,11,11,11,11,10,10,10,10,
+	14,14,14,14,10,10,10,10,11,11,11,11,10,10,10,10,
+	13,13,13,13,10,10,10,10,11,11,11,11,10,10,10,10,
+	13,13,13,13,10,10,10,10,11,11,11,11,10,10,10,10,
+	15,15,15,15,10,10,10,10,11,11,11,11,10,10,10,10,
+	15,15,15,15,10,10,10,10,11,11,11,11,10,10,10,10,
+	13,13,13,13,10,10,10,10,11,11,11,11,10,10,10,10,
+	13,13,13,13,10,10,10,10,11,11,11,11,10,10,10,10,
+	15,15,15,15,10,10,10,10,11,11,11,11,10,10,10,10,
+	15,15,15,15,10,10,10,10,11,11,11,11,10,10,10,10,
+	13,13,13,13,10,10,10,10,11,11,11,11,10,10,10,10,
+	13,13,13,13,10,10,10,10,11,11,11,11,10,10,10,10,
+};
+
+static const u8 irq_prio_d[256] = {
+	 0,16,17,16,18,16,17,16,19,16,17,16,18,16,17,16,
+	20,16,17,16,18,16,17,16,19,16,17,16,18,16,17,16,
+	21,16,17,16,18,16,17,16,19,16,17,16,18,16,17,16,
+	21,16,17,16,18,16,17,16,19,16,17,16,18,16,17,16,
+	22,16,17,16,18,16,17,16,19,16,17,16,18,16,17,16,
+	22,16,17,16,18,16,17,16,19,16,17,16,18,16,17,16,
+	21,16,17,16,18,16,17,16,19,16,17,16,18,16,17,16,
+	21,16,17,16,18,16,17,16,19,16,17,16,18,16,17,16,
+	23,16,17,16,18,16,17,16,19,16,17,16,18,16,17,16,
+	23,16,17,16,18,16,17,16,19,16,17,16,18,16,17,16,
+	21,16,17,16,18,16,17,16,19,16,17,16,18,16,17,16,
+	21,16,17,16,18,16,17,16,19,16,17,16,18,16,17,16,
+	22,16,17,16,18,16,17,16,19,16,17,16,18,16,17,16,
+	22,16,17,16,18,16,17,16,19,16,17,16,18,16,17,16,
+	21,16,17,16,18,16,17,16,19,16,17,16,18,16,17,16,
+	21,16,17,16,18,16,17,16,19,16,17,16,18,16,17,16,
+};
+
+static const u8 irq_prio_l[256] = {
+	 0, 0, 1, 0, 2, 2, 2, 2, 3, 3, 3, 3, 3, 3, 3, 3,
+	 4, 0, 1, 0, 2, 2, 2, 2, 3, 3, 3, 3, 3, 3, 3, 3,
+	 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5,
+	 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5,
+	 6, 6, 6, 6, 6, 6, 6, 6, 3, 3, 3, 3, 3, 3, 3, 3,
+	 6, 6, 6, 6, 6, 6, 6, 6, 3, 3, 3, 3, 3, 3, 3, 3,
+	 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5,
+	 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5,
+	 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7,
+	 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7,
+	 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7,
+	 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7,
+	 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7,
+	 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7,
+	 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7,
+	 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7, 7,
+};
+
+static int iomd_get_irq_nr(void)
+{
+	int irq;
+	u8 reg;
+
+	/* get highest priority first */
+	reg = readb(IOC_BASE + IOMD_IRQREQB);
+	irq = irq_prio_h[reg];
+	if (irq)
+		return irq;
+
+	/* get DMA  */
+	reg = readb(IOC_BASE + IOMD_DMAREQ);
+	irq = irq_prio_d[reg];
+	if (irq)
+		return irq;
+
+	/* get low priority */
+	reg = readb(IOC_BASE + IOMD_IRQREQA);
+	irq = irq_prio_l[reg];
+	if (irq)
+		return irq;
+	return 0;
+}
+
+static void iomd_handle_irq(struct pt_regs *regs)
+{
+	int irq;
+
+	do {
+		irq = iomd_get_irq_nr();
+		if (irq)
+			generic_handle_irq(irq);
+	} while (irq);
+}
+
 static void __iomem *iomd_get_base(struct irq_data *d)
 {
 	void *cd = irq_data_get_irq_chip_data(d);
@@ -82,6 +175,8 @@ void __init rpc_init_irq(void)
 	set_fiq_handler(&rpc_default_fiq_start,
 		&rpc_default_fiq_end - &rpc_default_fiq_start);
 
+	set_handle_irq(iomd_handle_irq);
+
 	for (irq = 0; irq < NR_IRQS; irq++) {
 		clr = IRQ_NOREQUEST;
 		set = 0;
diff --git a/arch/arm/mach-s3c/Kconfig b/arch/arm/mach-s3c/Kconfig
index 25606e668cf9..a64143574546 100644
--- a/arch/arm/mach-s3c/Kconfig
+++ b/arch/arm/mach-s3c/Kconfig
@@ -43,12 +43,12 @@ config SAMSUNG_ATAGS
 	def_bool n
 	depends on ATAGS
 	help
-	   This option enables ATAGS based boot support code for
-	   Samsung platforms, including static platform devices, legacy
-	   clock, timer and interrupt initialization, etc.
+	  This option enables ATAGS based boot support code for
+	  Samsung platforms, including static platform devices, legacy
+	  clock, timer and interrupt initialization, etc.
 
-	   Platforms that support only DT based boot need not to select
-	   this option.
+	  Platforms that support only DT based boot need not to select
+	  this option.
 
 if SAMSUNG_ATAGS
 
@@ -102,7 +102,7 @@ config S3C_DEV_HSMMC3
 config S3C_DEV_HWMON
 	bool
 	help
-	    Compile in platform device definitions for HWMON
+	  Compile in platform device definitions for HWMON
 
 config S3C_DEV_I2C1
 	bool
@@ -191,22 +191,10 @@ config S3C64XX_DEV_SPI0
 	  Compile in platform device definitions for S3C64XX's type
 	  SPI controller 0
 
-config S3C64XX_DEV_SPI1
-	bool
-	help
-	  Compile in platform device definitions for S3C64XX's type
-	  SPI controller 1
-
-config S3C64XX_DEV_SPI2
-	bool
-	help
-	  Compile in platform device definitions for S3C64XX's type
-	  SPI controller 2
-
 config SAMSUNG_DEV_TS
 	bool
 	help
-	    Common in platform device definitions for touchscreen device
+	  Common in platform device definitions for touchscreen device
 
 config SAMSUNG_DEV_KEYPAD
 	bool
@@ -219,14 +207,6 @@ config SAMSUNG_DEV_PWM
 	help
 	  Compile in platform device definition for PWM Timer
 
-config S3C24XX_PWM
-	bool "PWM device support"
-	select PWM
-	select PWM_SAMSUNG
-	help
-	  Support for exporting the PWM timer blocks via the pwm device
-	  system
-
 config GPIO_SAMSUNG
 	def_bool y
 
diff --git a/arch/arm/mach-s3c/Kconfig.s3c24xx b/arch/arm/mach-s3c/Kconfig.s3c24xx
index 000e3e234f71..7287e173f30e 100644
--- a/arch/arm/mach-s3c/Kconfig.s3c24xx
+++ b/arch/arm/mach-s3c/Kconfig.s3c24xx
@@ -4,6 +4,27 @@
 #		http://www.samsung.com/
 #
 # Copyright 2007 Simtec Electronics
+menuconfig ARCH_S3C24XX
+	bool "Samsung S3C24XX SoCs (deprecated, see help)"
+	depends on ARCH_MULTI_V4T || ARCH_MULTI_V5
+	depends on CPU_LITTLE_ENDIAN
+	depends on ATAGS && UNUSED_BOARD_FILES
+	select CLKSRC_SAMSUNG_PWM
+	select GPIO_SAMSUNG
+	select GPIOLIB
+	select S3C2410_WATCHDOG
+	select SAMSUNG_ATAGS
+	select WATCHDOG
+	help
+	  Samsung S3C2410, S3C2412, S3C2413, S3C2416, S3C2440, S3C2442, S3C2443
+	  and S3C2450 SoCs based systems, such as the Simtec Electronics BAST
+	  (<http://www.simtec.co.uk/products/EB110ITX/>), the IPAQ 1940 or the
+	  Samsung SMDK2410 development board (and derivatives).
+
+	  The platform is deprecated and scheduled for removal. Please reach to
+	  the maintainers of the platform and linux-samsung-soc@vger.kernel.org if
+	  you still use it.
+	  Without such feedback, the platform will be removed after 2022.
 
 if ARCH_S3C24XX
 
@@ -12,19 +33,17 @@ config PLAT_S3C24XX
 	select GPIOLIB
 	select NO_IOPORT_MAP
 	select S3C_DEV_NAND
-	select IRQ_DOMAIN
 	select COMMON_CLK
 	help
 	  Base platform code for any Samsung S3C24XX device
 
-
-
 menu "Samsung S3C24XX SoCs Support"
 
 comment "S3C24XX SoCs"
 
 config CPU_S3C2410
 	bool "Samsung S3C2410"
+	depends on ARCH_MULTI_V4T
 	default y
 	select CPU_ARM920T
 	select S3C2410_COMMON_CLK
@@ -36,6 +55,7 @@ config CPU_S3C2410
 
 config CPU_S3C2412
 	bool "Samsung S3C2412"
+	depends on ARCH_MULTI_V5
 	select CPU_ARM926T
 	select S3C2412_COMMON_CLK
 	select S3C2412_PM if PM_SLEEP
@@ -44,6 +64,7 @@ config CPU_S3C2412
 
 config CPU_S3C2416
 	bool "Samsung S3C2416/S3C2450"
+	depends on ARCH_MULTI_V5
 	select CPU_ARM926T
 	select S3C2416_PM if PM_SLEEP
 	select S3C2443_COMMON_CLK
@@ -52,6 +73,7 @@ config CPU_S3C2416
 
 config CPU_S3C2440
 	bool "Samsung S3C2440"
+	depends on ARCH_MULTI_V4T
 	select CPU_ARM920T
 	select S3C2410_COMMON_CLK
 	select S3C2410_PM if PM_SLEEP
@@ -60,6 +82,7 @@ config CPU_S3C2440
 
 config CPU_S3C2442
 	bool "Samsung S3C2442"
+	depends on ARCH_MULTI_V4T
 	select CPU_ARM920T
 	select S3C2410_COMMON_CLK
 	select S3C2410_PM if PM_SLEEP
@@ -72,6 +95,7 @@ config CPU_S3C244X
 
 config CPU_S3C2443
 	bool "Samsung S3C2443"
+	depends on ARCH_MULTI_V4T
 	select CPU_ARM920T
 	select S3C2443_COMMON_CLK
 	help
@@ -181,7 +205,6 @@ config MACH_AML_M5900
 
 config ARCH_BAST
 	bool "Simtec Electronics BAST (EB2410ITX)"
-	select ISA
 	select MACH_BAST_IDE
 	select S3C2410_COMMON_DCLK
 	select S3C2410_IOTIMING if ARM_S3C2410_CPUFREQ
@@ -268,7 +291,7 @@ config MACH_VR1000
 	help
 	  Say Y here if you are using the Thorcom VR1000 board.
 
-endif	# CPU_S3C2410
+endif # CPU_S3C2410
 
 config S3C2412_PM_SLEEP
 	bool
@@ -342,7 +365,7 @@ config MACH_VSTMS
 	help
 	  Say Y here if you are using an VSTMS board
 
-endif	# CPU_S3C2412
+endif # CPU_S3C2412
 
 if CPU_S3C2416
 
@@ -390,7 +413,7 @@ config MACH_S3C2416_DT
 	  Note: This is under development and not all peripherals can be supported
 	  with this machine file.
 
-endif	# CPU_S3C2416
+endif # CPU_S3C2416
 
 if CPU_S3C2440 || CPU_S3C2442
 
@@ -419,7 +442,7 @@ config S3C2440_PLL_16934400
 	default y if S3C24XX_PLL
 	help
 	  PLL tables for S3C2440 or S3C2442 CPUs with 16.934MHz crystals.
-endif
+endif # CPU_S3C2440 || CPU_S3C2442
 
 if CPU_S3C2440
 
@@ -515,7 +538,7 @@ config SMDK2440_CPU2440
 	default y if ARCH_S3C2440
 	select S3C2440_XTAL_16934400
 
-endif	# CPU_S3C2440
+endif # CPU_S3C2440
 
 if CPU_S3C2442
 
@@ -532,10 +555,9 @@ config MACH_NEO1973_GTA02
 	select MFD_PCF50633
 	select PCF50633_GPIO
 	select POWER_SUPPLY
-	select S3C24XX_PWM
 	select S3C_DEV_USB_HOST
 	help
-	   Say Y here if you are using the Openmoko GTA02 / Freerunner GSM Phone
+	  Say Y here if you are using the Openmoko GTA02 / Freerunner GSM Phone
 
 config MACH_RX1950
 	bool "HP iPAQ rx1950"
@@ -544,12 +566,11 @@ config MACH_RX1950
 	select S3C2410_COMMON_DCLK
 	select S3C2410_IOTIMING if ARM_S3C2440_CPUFREQ
 	select S3C2440_XTAL_16934400
-	select S3C24XX_PWM
 	select S3C_DEV_NAND
 	help
-	   Say Y here if you're using HP iPAQ rx1950
+	  Say Y here if you're using HP iPAQ rx1950
 
-endif	# CPU_S3C2442
+endif # CPU_S3C2442
 
 if CPU_S3C2443 || CPU_S3C2416
 
@@ -558,7 +579,7 @@ config S3C2443_SETUP_SPI
 	help
 	  Common setup code for SPI GPIO configurations
 
-endif	# CPU_S3C2443 || CPU_S3C2416
+endif # CPU_S3C2443 || CPU_S3C2416
 
 if CPU_S3C2443
 
@@ -571,13 +592,13 @@ config MACH_SMDK2443
 	help
 	  Say Y here if you are using an SMDK2443
 
-endif	# CPU_S3C2443
+endif # CPU_S3C2443
 
 config PM_H1940
 	bool
 	help
 	  Internal node for H1940 and related PM
 
-endmenu	# Samsung S3C24XX SoCs Support
+endmenu # "Samsung S3C24XX SoCs Support"
 
-endif	# ARCH_S3C24XX
+endif # ARCH_S3C24XX
diff --git a/arch/arm/mach-s3c/Kconfig.s3c64xx b/arch/arm/mach-s3c/Kconfig.s3c64xx
index f3fcb570edf5..0c1b91c3ac5f 100644
--- a/arch/arm/mach-s3c/Kconfig.s3c64xx
+++ b/arch/arm/mach-s3c/Kconfig.s3c64xx
@@ -4,7 +4,7 @@
 #	Simtec Electronics, Ben Dooks <ben@simtec.co.uk>
 
 menuconfig ARCH_S3C64XX
-	bool "Samsung S3C64XX"
+	bool "Samsung S3C64XX (deprecated, see help)"
 	depends on ARCH_MULTI_V6
 	select ARM_AMBA
 	select ARM_VIC
@@ -12,7 +12,6 @@ menuconfig ARCH_S3C64XX
 	select COMMON_CLK_SAMSUNG
 	select GPIO_SAMSUNG if ATAGS
 	select GPIOLIB
-	select HAVE_S3C2410_I2C if I2C
 	select HAVE_TCM
 	select PLAT_SAMSUNG
 	select PM_GENERIC_DOMAINS if PM
@@ -25,6 +24,11 @@ menuconfig ARCH_S3C64XX
 	help
 	  Samsung S3C64XX series based systems
 
+	  The platform is deprecated and scheduled for removal. Please reach to
+	  the maintainers of the platform and linux-samsung-soc@vger.kernel.org if
+	  you still use it.
+	  Without such feedback, the platform will be removed after 2024.
+
 if ARCH_S3C64XX
 
 # Configuration options for the S3C6410 CPU
@@ -100,7 +104,7 @@ config S3C64XX_SETUP_SDHCI_GPIO
 config S3C64XX_SETUP_SPI
 	bool
 	help
-	 Common setup code for SPI GPIO configurations
+	  Common setup code for SPI GPIO configurations
 
 config S3C64XX_SETUP_USB_PHY
 	bool
@@ -110,8 +114,8 @@ config S3C64XX_SETUP_USB_PHY
 # S36400 Macchine support
 
 config MACH_SMDK6400
-       bool "SMDK6400"
-	depends on ATAGS
+	bool "SMDK6400"
+	depends on ATAGS && UNUSED_BOARD_FILES
 	select CPU_S3C6400
 	select S3C64XX_SETUP_SDHCI
 	select S3C_DEV_HSMMC1
@@ -122,7 +126,7 @@ config MACH_SMDK6400
 
 config MACH_ANW6410
 	bool "A&W6410"
-	depends on ATAGS
+	depends on ATAGS && UNUSED_BOARD_FILES
 	select CPU_S3C6410
 	select S3C64XX_SETUP_FB_24BPP
 	select S3C_DEV_FB
@@ -131,7 +135,7 @@ config MACH_ANW6410
 
 config MACH_MINI6410
 	bool "MINI6410"
-	depends on ATAGS
+	depends on ATAGS && UNUSED_BOARD_FILES
 	select CPU_S3C6410
 	select S3C64XX_SETUP_FB_24BPP
 	select S3C64XX_SETUP_SDHCI
@@ -147,7 +151,7 @@ config MACH_MINI6410
 
 config MACH_REAL6410
 	bool "REAL6410"
-	depends on ATAGS
+	depends on ATAGS && UNUSED_BOARD_FILES
 	select CPU_S3C6410
 	select S3C64XX_SETUP_FB_24BPP
 	select S3C64XX_SETUP_SDHCI
@@ -163,7 +167,7 @@ config MACH_REAL6410
 
 config MACH_SMDK6410
 	bool "SMDK6410"
-	depends on ATAGS
+	depends on ATAGS && UNUSED_BOARD_FILES
 	select CPU_S3C6410
 	select S3C64XX_SETUP_FB_24BPP
 	select S3C64XX_SETUP_I2C1
@@ -201,7 +205,7 @@ config SMDK6410_SD_CH0
 	bool "Use channel 0 only"
 	depends on MACH_SMDK6410
 	help
-          Select CON7 (channel 0) as the MMC/SD slot, as
+	  Select CON7 (channel 0) as the MMC/SD slot, as
 	  at least some SMDK6410 boards come with the
 	  resistors fitted so that the card detects for
 	  channels 0 and 1 are the same.
@@ -210,7 +214,7 @@ config SMDK6410_SD_CH1
 	bool "Use channel 1 only"
 	depends on MACH_SMDK6410
 	help
-          Select CON6 (channel 1) as the MMC/SD slot, as
+	  Select CON6 (channel 1) as the MMC/SD slot, as
 	  at least some SMDK6410 boards come with the
 	  resistors fitted so that the card detects for
 	  channels 0 and 1 are the same.
@@ -250,17 +254,17 @@ config SMDK6410_WM1192_EV1
 
 config MACH_NCP
 	bool "NCP"
-	depends on ATAGS
+	depends on ATAGS && UNUSED_BOARD_FILES
 	select CPU_S3C6410
 	select S3C64XX_SETUP_I2C1
 	select S3C_DEV_HSMMC1
 	select S3C_DEV_I2C1
 	help
-          Machine support for the Samsung NCP
+	  Machine support for the Samsung NCP
 
 config MACH_HMT
 	bool "Airgoo HMT"
-	depends on ATAGS
+	depends on ATAGS && UNUSED_BOARD_FILES
 	select CPU_S3C6410
 	select S3C64XX_SETUP_FB_24BPP
 	select S3C_DEV_FB
@@ -288,21 +292,21 @@ config MACH_SMARTQ
 	select SAMSUNG_DEV_PWM
 	select SAMSUNG_DEV_TS
 	help
-	    Shared machine support for SmartQ 5/7
+	  Shared machine support for SmartQ 5/7
 
 config MACH_SMARTQ5
 	bool "SmartQ 5"
-	depends on ATAGS
+	depends on ATAGS && UNUSED_BOARD_FILES
 	select MACH_SMARTQ
 	help
-	    Machine support for the SmartQ 5
+	  Machine support for the SmartQ 5
 
 config MACH_SMARTQ7
 	bool "SmartQ 7"
-	depends on ATAGS
+	depends on ATAGS && UNUSED_BOARD_FILES
 	select MACH_SMARTQ
 	help
-	    Machine support for the SmartQ 7
+	  Machine support for the SmartQ 7
 
 config MACH_WLF_CRAGG_6410
 	bool "Wolfson Cragganmore 6410"
diff --git a/arch/arm/mach-s3c/Makefile b/arch/arm/mach-s3c/Makefile
index 54188d10ab2e..7c7d3318fd61 100644
--- a/arch/arm/mach-s3c/Makefile
+++ b/arch/arm/mach-s3c/Makefile
@@ -2,8 +2,6 @@
 #
 # Copyright 2009 Simtec Electronics
 
-ccflags-$(CONFIG_ARCH_MULTIPLATFORM) += -I$(srctree)/$(src)/include
-
 ifdef CONFIG_ARCH_S3C24XX
 include $(src)/Makefile.s3c24xx
 endif
diff --git a/arch/arm/mach-s3c/Makefile.boot b/arch/arm/mach-s3c/Makefile.boot
deleted file mode 100644
index 7f19e226035e..000000000000
--- a/arch/arm/mach-s3c/Makefile.boot
+++ /dev/null
@@ -1,9 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0
-
-ifeq ($(CONFIG_PM_H1940),y)
-	zreladdr-y	+= 0x30108000
-	params_phys-y	:= 0x30100100
-else
-	zreladdr-y	+= 0x30008000
-	params_phys-y	:= 0x30000100
-endif
diff --git a/arch/arm/mach-s3c/Makefile.s3c64xx b/arch/arm/mach-s3c/Makefile.s3c64xx
index 0c18e31936df..21e919bf2cd1 100644
--- a/arch/arm/mach-s3c/Makefile.s3c64xx
+++ b/arch/arm/mach-s3c/Makefile.s3c64xx
@@ -3,9 +3,6 @@
 # Copyright 2008 Openmoko, Inc.
 # Copyright 2008 Simtec Electronics
 
-ccflags-$(CONFIG_ARCH_MULTIPLATFORM) := -I$(srctree)/$(src)/include
-asflags-$(CONFIG_ARCH_MULTIPLATFORM) := -I$(srctree)/$(src)/include
-
 # PM
 
 obj-$(CONFIG_PM)		+= pm-s3c64xx.o
diff --git a/arch/arm/mach-s3c/bast-ide.c b/arch/arm/mach-s3c/bast-ide.c
index da64db1811d8..67f0adc1fec0 100644
--- a/arch/arm/mach-s3c/bast-ide.c
+++ b/arch/arm/mach-s3c/bast-ide.c
@@ -20,7 +20,7 @@
 #include <asm/mach/irq.h>
 
 #include "map.h"
-#include <mach/irqs.h>
+#include "irqs.h"
 
 #include "bast.h"
 
diff --git a/arch/arm/mach-s3c/bast-irq.c b/arch/arm/mach-s3c/bast-irq.c
index d299f124e6dc..cfc2ddc65513 100644
--- a/arch/arm/mach-s3c/bast-irq.c
+++ b/arch/arm/mach-s3c/bast-irq.c
@@ -16,7 +16,7 @@
 #include <asm/mach/irq.h>
 
 #include "regs-irq.h"
-#include <mach/irqs.h>
+#include "irqs.h"
 
 #include "bast.h"
 
diff --git a/arch/arm/mach-s3c/cpu.c b/arch/arm/mach-s3c/cpu.c
index 6e9772555f0d..3491f790d575 100644
--- a/arch/arm/mach-s3c/cpu.c
+++ b/arch/arm/mach-s3c/cpu.c
@@ -10,7 +10,7 @@
 #include <linux/init.h>
 #include <linux/io.h>
 
-#include <mach/map-base.h>
+#include "map-base.h"
 #include "cpu.h"
 
 unsigned long samsung_cpu_id;
@@ -28,4 +28,5 @@ void __init s3c64xx_init_cpu(void)
 	}
 
 	pr_info("Samsung CPU ID: 0x%08lx\n", samsung_cpu_id);
+	pr_err("The platform is deprecated and scheduled for removal. Please reach to the maintainers of the platform and linux-samsung-soc@vger.kernel.org if you still use it.  Without such feedback, the platform will be removed after 2022.\n");
 }
diff --git a/arch/arm/mach-s3c/dev-audio-s3c64xx.c b/arch/arm/mach-s3c/dev-audio-s3c64xx.c
index fc2f077afd24..909e82c148ba 100644
--- a/arch/arm/mach-s3c/dev-audio-s3c64xx.c
+++ b/arch/arm/mach-s3c/dev-audio-s3c64xx.c
@@ -10,7 +10,7 @@
 #include <linux/gpio.h>
 #include <linux/export.h>
 
-#include <mach/irqs.h>
+#include "irqs.h"
 #include "map.h"
 
 #include "devs.h"
diff --git a/arch/arm/mach-s3c/dev-uart-s3c64xx.c b/arch/arm/mach-s3c/dev-uart-s3c64xx.c
index 8288e8d6c092..f9c947b8971b 100644
--- a/arch/arm/mach-s3c/dev-uart-s3c64xx.c
+++ b/arch/arm/mach-s3c/dev-uart-s3c64xx.c
@@ -16,7 +16,7 @@
 #include <asm/mach/arch.h>
 #include <asm/mach/irq.h>
 #include "map.h"
-#include <mach/irqs.h>
+#include "irqs.h"
 
 #include "devs.h"
 
diff --git a/arch/arm/mach-s3c/devs.c b/arch/arm/mach-s3c/devs.c
index 06dec64848f9..9ac07c023adf 100644
--- a/arch/arm/mach-s3c/devs.c
+++ b/arch/arm/mach-s3c/devs.c
@@ -38,7 +38,7 @@
 #include <asm/mach/map.h>
 #include <asm/mach/irq.h>
 
-#include <mach/irqs.h>
+#include "irqs.h"
 #include "map.h"
 #include "gpio-samsung.h"
 #include "gpio-cfg.h"
@@ -1107,8 +1107,7 @@ struct platform_device s3c64xx_device_spi0 = {
 	},
 };
 
-void __init s3c64xx_spi0_set_platdata(int (*cfg_gpio)(void), int src_clk_nr,
-						int num_cs)
+void __init s3c64xx_spi0_set_platdata(int src_clk_nr, int num_cs)
 {
 	struct s3c64xx_spi_info pd;
 
@@ -1120,80 +1119,8 @@ void __init s3c64xx_spi0_set_platdata(int (*cfg_gpio)(void), int src_clk_nr,
 
 	pd.num_cs = num_cs;
 	pd.src_clk_nr = src_clk_nr;
-	pd.cfg_gpio = (cfg_gpio) ? cfg_gpio : s3c64xx_spi0_cfg_gpio;
+	pd.cfg_gpio = s3c64xx_spi0_cfg_gpio;
 
 	s3c_set_platdata(&pd, sizeof(pd), &s3c64xx_device_spi0);
 }
 #endif /* CONFIG_S3C64XX_DEV_SPI0 */
-
-#ifdef CONFIG_S3C64XX_DEV_SPI1
-static struct resource s3c64xx_spi1_resource[] = {
-	[0] = DEFINE_RES_MEM(S3C_PA_SPI1, SZ_256),
-	[1] = DEFINE_RES_IRQ(IRQ_SPI1),
-};
-
-struct platform_device s3c64xx_device_spi1 = {
-	.name		= "s3c6410-spi",
-	.id		= 1,
-	.num_resources	= ARRAY_SIZE(s3c64xx_spi1_resource),
-	.resource	= s3c64xx_spi1_resource,
-	.dev = {
-		.dma_mask		= &samsung_device_dma_mask,
-		.coherent_dma_mask	= DMA_BIT_MASK(32),
-	},
-};
-
-void __init s3c64xx_spi1_set_platdata(int (*cfg_gpio)(void), int src_clk_nr,
-						int num_cs)
-{
-	struct s3c64xx_spi_info pd;
-
-	/* Reject invalid configuration */
-	if (!num_cs || src_clk_nr < 0) {
-		pr_err("%s: Invalid SPI configuration\n", __func__);
-		return;
-	}
-
-	pd.num_cs = num_cs;
-	pd.src_clk_nr = src_clk_nr;
-	pd.cfg_gpio = (cfg_gpio) ? cfg_gpio : s3c64xx_spi1_cfg_gpio;
-
-	s3c_set_platdata(&pd, sizeof(pd), &s3c64xx_device_spi1);
-}
-#endif /* CONFIG_S3C64XX_DEV_SPI1 */
-
-#ifdef CONFIG_S3C64XX_DEV_SPI2
-static struct resource s3c64xx_spi2_resource[] = {
-	[0] = DEFINE_RES_MEM(S3C_PA_SPI2, SZ_256),
-	[1] = DEFINE_RES_IRQ(IRQ_SPI2),
-};
-
-struct platform_device s3c64xx_device_spi2 = {
-	.name		= "s3c6410-spi",
-	.id		= 2,
-	.num_resources	= ARRAY_SIZE(s3c64xx_spi2_resource),
-	.resource	= s3c64xx_spi2_resource,
-	.dev = {
-		.dma_mask		= &samsung_device_dma_mask,
-		.coherent_dma_mask	= DMA_BIT_MASK(32),
-	},
-};
-
-void __init s3c64xx_spi2_set_platdata(int (*cfg_gpio)(void), int src_clk_nr,
-						int num_cs)
-{
-	struct s3c64xx_spi_info pd;
-
-	/* Reject invalid configuration */
-	if (!num_cs || src_clk_nr < 0) {
-		pr_err("%s: Invalid SPI configuration\n", __func__);
-		return;
-	}
-
-	pd.num_cs = num_cs;
-	pd.src_clk_nr = src_clk_nr;
-	pd.cfg_gpio = (cfg_gpio) ? cfg_gpio : s3c64xx_spi2_cfg_gpio;
-
-	s3c_set_platdata(&pd, sizeof(pd), &s3c64xx_device_spi2);
-}
-#endif /* CONFIG_S3C64XX_DEV_SPI2 */
diff --git a/arch/arm/mach-s3c/devs.h b/arch/arm/mach-s3c/devs.h
index 02b0c5750572..991b9b2006a1 100644
--- a/arch/arm/mach-s3c/devs.h
+++ b/arch/arm/mach-s3c/devs.h
@@ -33,8 +33,6 @@ extern struct platform_device s3c64xx_device_onenand1;
 extern struct platform_device s3c64xx_device_pcm0;
 extern struct platform_device s3c64xx_device_pcm1;
 extern struct platform_device s3c64xx_device_spi0;
-extern struct platform_device s3c64xx_device_spi1;
-extern struct platform_device s3c64xx_device_spi2;
 
 extern struct platform_device s3c_device_adc;
 extern struct platform_device s3c_device_cfcon;
diff --git a/arch/arm/mach-s3c/gpio-samsung.c b/arch/arm/mach-s3c/gpio-samsung.c
index 76ef415789f2..b7fc7c41309c 100644
--- a/arch/arm/mach-s3c/gpio-samsung.c
+++ b/arch/arm/mach-s3c/gpio-samsung.c
@@ -26,7 +26,7 @@
 
 #include <asm/irq.h>
 
-#include <mach/irqs.h>
+#include "irqs.h"
 #include "map.h"
 #include "regs-gpio.h"
 #include "gpio-samsung.h"
@@ -35,6 +35,7 @@
 #include "gpio-core.h"
 #include "gpio-cfg.h"
 #include "gpio-cfg-helpers.h"
+#include "hardware-s3c24xx.h"
 #include "pm.h"
 
 int samsung_gpio_setpull_updown(struct samsung_gpio_chip *chip,
diff --git a/arch/arm/mach-s3c/include/mach/io-s3c24xx.h b/arch/arm/mach-s3c/include/mach/io-s3c24xx.h
deleted file mode 100644
index 738b775d3336..000000000000
--- a/arch/arm/mach-s3c/include/mach/io-s3c24xx.h
+++ /dev/null
@@ -1,50 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-/*
- * arch/arm/mach-s3c2410/include/mach/io.h
- *  from arch/arm/mach-rpc/include/mach/io.h
- *
- * Copyright (C) 1997 Russell King
- *	     (C) 2003 Simtec Electronics
-*/
-
-#ifndef __ASM_ARM_ARCH_IO_S3C24XX_H
-#define __ASM_ARM_ARCH_IO_S3C24XX_H
-
-#include <mach/map-base.h>
-
-/*
- * ISA style IO, for each machine to sort out mappings for,
- * if it implements it. We reserve two 16M regions for ISA,
- * so the PC/104 can use separate addresses for 8-bit and
- * 16-bit port I/O.
- */
-#define PCIO_BASE		S3C_ADDR(0x02000000)
-#define IO_SPACE_LIMIT		0x00ffffff
-#define S3C24XX_VA_ISA_WORD	(PCIO_BASE)
-#define S3C24XX_VA_ISA_BYTE	(PCIO_BASE + 0x01000000)
-
-#ifdef CONFIG_ISA
-
-#define inb(p)		readb(S3C24XX_VA_ISA_BYTE + (p))
-#define inw(p)		readw(S3C24XX_VA_ISA_WORD + (p))
-#define inl(p)		readl(S3C24XX_VA_ISA_WORD + (p))
-
-#define outb(v,p)	writeb((v), S3C24XX_VA_ISA_BYTE + (p))
-#define outw(v,p)	writew((v), S3C24XX_VA_ISA_WORD + (p))
-#define outl(v,p)	writel((v), S3C24XX_VA_ISA_WORD + (p))
-
-#define insb(p,d,l)	readsb(S3C24XX_VA_ISA_BYTE + (p),d,l)
-#define insw(p,d,l)	readsw(S3C24XX_VA_ISA_WORD + (p),d,l)
-#define insl(p,d,l)	readsl(S3C24XX_VA_ISA_WORD + (p),d,l)
-
-#define outsb(p,d,l)	writesb(S3C24XX_VA_ISA_BYTE + (p),d,l)
-#define outsw(p,d,l)	writesw(S3C24XX_VA_ISA_WORD + (p),d,l)
-#define outsl(p,d,l)	writesl(S3C24XX_VA_ISA_WORD + (p),d,l)
-
-#else
-
-#define __io(x) (PCIO_BASE + (x))
-
-#endif
-
-#endif
diff --git a/arch/arm/mach-s3c/include/mach/io.h b/arch/arm/mach-s3c/include/mach/io.h
deleted file mode 100644
index 30a0135708dc..000000000000
--- a/arch/arm/mach-s3c/include/mach/io.h
+++ /dev/null
@@ -1,8 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-/*
- * Copyright (c) 2020 Krzysztof Kozlowski <krzk@kernel.org>
- */
-
-#ifdef CONFIG_ARCH_S3C24XX
-#include "io-s3c24xx.h"
-#endif
diff --git a/arch/arm/mach-s3c/init.c b/arch/arm/mach-s3c/init.c
index 9d92f03e9bc1..bf513616f55d 100644
--- a/arch/arm/mach-s3c/init.c
+++ b/arch/arm/mach-s3c/init.c
@@ -59,6 +59,8 @@ void __init s3c_init_cpu(unsigned long idcode,
 
 	if (cpu->map_io)
 		cpu->map_io();
+
+	pr_err("The platform is deprecated and scheduled for removal. Please reach to the maintainers of the platform and linux-samsung-soc@vger.kernel.org if you still use it.  Without such feedback, the platform will be removed after 2022.\n");
 }
 
 /* s3c24xx_init_clocks
diff --git a/arch/arm/mach-s3c/iotiming-s3c2410.c b/arch/arm/mach-s3c/iotiming-s3c2410.c
index 28d9f473e24a..09f388d8f824 100644
--- a/arch/arm/mach-s3c/iotiming-s3c2410.c
+++ b/arch/arm/mach-s3c/iotiming-s3c2410.c
@@ -259,7 +259,7 @@ static const unsigned int tacc_tab[] = {
 /**
  * get_tacc - turn tACC value into cycle time
  * @hclk_tns: The cycle time for HCLK, in 10ths of nanoseconds.
- * @val: The bank timing register value, shifed down.
+ * @val: The bank timing register value, shifted down.
  */
 static unsigned int get_tacc(unsigned long hclk_tns,
 			     unsigned long val)
diff --git a/arch/arm/mach-s3c/irq-pm-s3c24xx.c b/arch/arm/mach-s3c/irq-pm-s3c24xx.c
index 4d5e28312d91..55f41135ad70 100644
--- a/arch/arm/mach-s3c/irq-pm-s3c24xx.c
+++ b/arch/arm/mach-s3c/irq-pm-s3c24xx.c
@@ -15,7 +15,7 @@
 
 #include "cpu.h"
 #include "pm.h"
-#include <mach/map-base.h>
+#include "map-base.h"
 #include "map-s3c.h"
 
 #include "regs-irq.h"
diff --git a/arch/arm/mach-s3c/irq-s3c24xx.c b/arch/arm/mach-s3c/irq-s3c24xx.c
index 3776d5206f9b..088cc04b7431 100644
--- a/arch/arm/mach-s3c/irq-s3c24xx.c
+++ b/arch/arm/mach-s3c/irq-s3c24xx.c
@@ -26,7 +26,7 @@
 #include <asm/exception.h>
 #include <asm/mach/irq.h>
 
-#include <mach/irqs.h>
+#include "irqs.h"
 #include "regs-irq.h"
 #include "regs-gpio.h"
 
diff --git a/arch/arm/mach-s3c/include/mach/irqs-s3c24xx.h b/arch/arm/mach-s3c/irqs-s3c24xx.h
index aaf3bae08b52..fecbf7e440c6 100644
--- a/arch/arm/mach-s3c/include/mach/irqs-s3c24xx.h
+++ b/arch/arm/mach-s3c/irqs-s3c24xx.h
@@ -108,6 +108,8 @@
 #define IRQ_TC			S3C2410_IRQSUB(9)
 #define IRQ_ADC			S3C2410_IRQSUB(10)
 
+#define NR_IRQS_S3C2410		(S3C2410_IRQSUB(10) + 1)
+
 /* extra irqs for s3c2412 */
 
 #define IRQ_S3C2412_CFSDI	S3C2410_IRQ(21)
@@ -115,6 +117,7 @@
 #define IRQ_S3C2412_SDI		S3C2410_IRQSUB(13)
 #define IRQ_S3C2412_CF		S3C2410_IRQSUB(14)
 
+#define NR_IRQS_S3C2412		(S3C2410_IRQSUB(14) + 1)
 
 #define IRQ_S3C2416_EINT8t15	S3C2410_IRQ(5)
 #define IRQ_S3C2416_DMA		S3C2410_IRQ(17)
@@ -146,13 +149,20 @@
 #define IRQ_S3C2416_I2S0	S3C2416_IRQ(6)
 #define IRQ_S3C2416_I2S1	S3C2416_IRQ(7)
 
-/* extra irqs for s3c2440 */
+#define NR_IRQS_S3C2416		(S3C2416_IRQ(7) + 1)
+
+/* extra irqs for s3c2440/s3c2442 */
 
 #define IRQ_S3C2440_CAM_C	S3C2410_IRQSUB(11)	/* S3C2443 too */
 #define IRQ_S3C2440_CAM_P	S3C2410_IRQSUB(12)	/* S3C2443 too */
+
+#define NR_IRQS_S3C2442		(S3C2410_IRQSUB(12) + 1)
+
 #define IRQ_S3C2440_WDT		S3C2410_IRQSUB(13)
 #define IRQ_S3C2440_AC97	S3C2410_IRQSUB(14)
 
+#define NR_IRQS_S3C2440		(S3C2410_IRQSUB(14) + 1)
+
 /* irqs for s3c2443 */
 
 #define IRQ_S3C2443_DMA		S3C2410_IRQ(17)		/* IRQ_DMA1 */
@@ -186,11 +196,7 @@
 #define IRQ_S3C2443_WDT		S3C2410_IRQSUB(27)
 #define IRQ_S3C2443_AC97	S3C2410_IRQSUB(28)
 
-#if defined(CONFIG_CPU_S3C2416)
-#define NR_IRQS (IRQ_S3C2416_I2S1 + 1)
-#else
-#define NR_IRQS (IRQ_S3C2443_AC97 + 1)
-#endif
+#define NR_IRQS_S3C2443		(S3C2410_IRQSUB(28) + 1)
 
 /* compatibility define. */
 #define IRQ_UART3		IRQ_S3C2443_UART3
diff --git a/arch/arm/mach-s3c/include/mach/irqs-s3c64xx.h b/arch/arm/mach-s3c/irqs-s3c64xx.h
index c244e480e6b3..c244e480e6b3 100644
--- a/arch/arm/mach-s3c/include/mach/irqs-s3c64xx.h
+++ b/arch/arm/mach-s3c/irqs-s3c64xx.h
diff --git a/arch/arm/mach-s3c/include/mach/irqs.h b/arch/arm/mach-s3c/irqs.h
index 0bff1c1c8eb0..0bff1c1c8eb0 100644
--- a/arch/arm/mach-s3c/include/mach/irqs.h
+++ b/arch/arm/mach-s3c/irqs.h
diff --git a/arch/arm/mach-s3c/mach-amlm5900.c b/arch/arm/mach-s3c/mach-amlm5900.c
index 94c4512ace17..f85e5885e9b4 100644
--- a/arch/arm/mach-s3c/mach-amlm5900.c
+++ b/arch/arm/mach-s3c/mach-amlm5900.c
@@ -239,7 +239,9 @@ static void __init amlm5900_init(void)
 
 MACHINE_START(AML_M5900, "AML_M5900")
 	.atag_offset	= 0x100,
+	.nr_irqs	= NR_IRQS_S3C2410,
 	.map_io		= amlm5900_map_io,
+	.nr_irqs	= NR_IRQS_S3C2410,
 	.init_irq	= s3c2410_init_irq,
 	.init_machine	= amlm5900_init,
 	.init_time	= amlm5900_init_time,
diff --git a/arch/arm/mach-s3c/mach-anubis.c b/arch/arm/mach-s3c/mach-anubis.c
index 04147cc0adcc..4536f3e66e27 100644
--- a/arch/arm/mach-s3c/mach-anubis.c
+++ b/arch/arm/mach-s3c/mach-anubis.c
@@ -57,11 +57,6 @@ static struct map_desc anubis_iodesc[] __initdata = {
 	.pfn		= __phys_to_pfn(0x0),
 	.length		= SZ_4M,
 	.type		= MT_DEVICE,
-  }, {
-	.virtual	= (u32)S3C24XX_VA_ISA_WORD,
-	.pfn		= __phys_to_pfn(0x0),
-	.length 	= SZ_4M,
-	.type		= MT_DEVICE,
   },
 
   /* we could possibly compress the next set down into a set of smaller tables
@@ -419,6 +414,7 @@ static void __init anubis_init(void)
 MACHINE_START(ANUBIS, "Simtec-Anubis")
 	/* Maintainer: Ben Dooks <ben@simtec.co.uk> */
 	.atag_offset	= 0x100,
+	.nr_irqs	= NR_IRQS_S3C2440,
 	.map_io		= anubis_map_io,
 	.init_machine	= anubis_init,
 	.init_irq	= s3c2440_init_irq,
diff --git a/arch/arm/mach-s3c/mach-anw6410.c b/arch/arm/mach-s3c/mach-anw6410.c
index 825714e9ac66..b67eae43e04f 100644
--- a/arch/arm/mach-s3c/mach-anw6410.c
+++ b/arch/arm/mach-s3c/mach-anw6410.c
@@ -40,7 +40,7 @@
 
 #include "devs.h"
 #include "cpu.h"
-#include <mach/irqs.h>
+#include "irqs.h"
 #include "regs-gpio.h"
 #include "gpio-samsung.h"
 
diff --git a/arch/arm/mach-s3c/mach-at2440evb.c b/arch/arm/mach-s3c/mach-at2440evb.c
index c6a5a51d84aa..743403d873e0 100644
--- a/arch/arm/mach-s3c/mach-at2440evb.c
+++ b/arch/arm/mach-s3c/mach-at2440evb.c
@@ -225,6 +225,7 @@ static void __init at2440evb_init(void)
 
 MACHINE_START(AT2440EVB, "AT2440EVB")
 	.atag_offset	= 0x100,
+	.nr_irqs	= NR_IRQS_S3C2440,
 	.map_io		= at2440evb_map_io,
 	.init_machine	= at2440evb_init,
 	.init_irq	= s3c2440_init_irq,
diff --git a/arch/arm/mach-s3c/mach-bast.c b/arch/arm/mach-s3c/mach-bast.c
index 27e8d5950228..a33ceab81e09 100644
--- a/arch/arm/mach-s3c/mach-bast.c
+++ b/arch/arm/mach-s3c/mach-bast.c
@@ -75,11 +75,6 @@ static struct map_desc bast_iodesc[] __initdata = {
 	  .pfn		= PA_CS2(BAST_PA_ISAIO),
 	  .length	= SZ_16M,
 	  .type		= MT_DEVICE,
-  }, {
-	  .virtual	= (u32)S3C24XX_VA_ISA_WORD,
-	  .pfn		= PA_CS3(BAST_PA_ISAIO),
-	  .length	= SZ_16M,
-	  .type		= MT_DEVICE,
   },
   /* bast CPLD control registers, and external interrupt controls */
   {
@@ -580,6 +575,7 @@ static void __init bast_init(void)
 MACHINE_START(BAST, "Simtec-BAST")
 	/* Maintainer: Ben Dooks <ben@simtec.co.uk> */
 	.atag_offset	= 0x100,
+	.nr_irqs	= NR_IRQS_S3C2410,
 	.map_io		= bast_map_io,
 	.init_irq	= s3c2410_init_irq,
 	.init_machine	= bast_init,
diff --git a/arch/arm/mach-s3c/mach-crag6410-module.c b/arch/arm/mach-s3c/mach-crag6410-module.c
index 407ad493493e..4edde13b89b5 100644
--- a/arch/arm/mach-s3c/mach-crag6410-module.c
+++ b/arch/arm/mach-s3c/mach-crag6410-module.c
@@ -28,14 +28,10 @@
 #include <linux/platform_data/spi-s3c64xx.h>
 
 #include "cpu.h"
-#include <mach/irqs.h>
+#include "irqs.h"
 
 #include "crag6410.h"
 
-static struct s3c64xx_spi_csinfo wm0010_spi_csinfo = {
-	.line = S3C64XX_GPC(3),
-};
-
 static struct wm0010_pdata wm0010_pdata = {
 	.gpio_reset = S3C64XX_GPN(6),
 	.reset_active_high = 1, /* Active high for Glenfarclas Rev 2 */
@@ -49,7 +45,6 @@ static struct spi_board_info wm1253_devs[] = {
 		.chip_select	= 0,
 		.mode		= SPI_MODE_0,
 		.irq		= S3C_EINT(4),
-		.controller_data = &wm0010_spi_csinfo,
 		.platform_data = &wm0010_pdata,
 	},
 };
@@ -62,7 +57,6 @@ static struct spi_board_info balblair_devs[] = {
 		.chip_select	= 0,
 		.mode		= SPI_MODE_0,
 		.irq		= S3C_EINT(4),
-		.controller_data = &wm0010_spi_csinfo,
 		.platform_data = &wm0010_pdata,
 	},
 };
@@ -229,10 +223,6 @@ static struct arizona_pdata wm5102_reva_pdata = {
 	},
 };
 
-static struct s3c64xx_spi_csinfo codec_spi_csinfo = {
-	.line = S3C64XX_GPN(5),
-};
-
 static struct spi_board_info wm5102_reva_spi_devs[] = {
 	[0] = {
 		.modalias	= "wm5102",
@@ -242,7 +232,6 @@ static struct spi_board_info wm5102_reva_spi_devs[] = {
 		.mode		= SPI_MODE_0,
 		.irq		= GLENFARCLAS_PMIC_IRQ_BASE +
 				  WM831X_IRQ_GPIO_2,
-		.controller_data = &codec_spi_csinfo,
 		.platform_data = &wm5102_reva_pdata,
 	},
 };
@@ -275,7 +264,6 @@ static struct spi_board_info wm5102_spi_devs[] = {
 		.mode		= SPI_MODE_0,
 		.irq		= GLENFARCLAS_PMIC_IRQ_BASE +
 				  WM831X_IRQ_GPIO_2,
-		.controller_data = &codec_spi_csinfo,
 		.platform_data = &wm5102_pdata,
 	},
 };
@@ -298,7 +286,6 @@ static struct spi_board_info wm5110_spi_devs[] = {
 		.mode		= SPI_MODE_0,
 		.irq		= GLENFARCLAS_PMIC_IRQ_BASE +
 				  WM831X_IRQ_GPIO_2,
-		.controller_data = &codec_spi_csinfo,
 		.platform_data = &wm5102_reva_pdata,
 	},
 };
diff --git a/arch/arm/mach-s3c/mach-crag6410.c b/arch/arm/mach-s3c/mach-crag6410.c
index 4a12c75d407f..9a45474d1bf7 100644
--- a/arch/arm/mach-s3c/mach-crag6410.c
+++ b/arch/arm/mach-s3c/mach-crag6410.c
@@ -47,7 +47,7 @@
 #include "map.h"
 #include "regs-gpio.h"
 #include "gpio-samsung.h"
-#include <mach/irqs.h>
+#include "irqs.h"
 
 #include "fb.h"
 #include "sdhci.h"
@@ -825,6 +825,15 @@ static const struct gpio_led_platform_data gpio_leds_pdata = {
 
 static struct dwc2_hsotg_plat crag6410_hsotg_pdata;
 
+static struct gpiod_lookup_table crag_spi0_gpiod_table = {
+	.dev_id = "s3c6410-spi.0",
+	.table = {
+		GPIO_LOOKUP_IDX("GPIOC", 3, "cs", 0, GPIO_ACTIVE_LOW),
+		GPIO_LOOKUP_IDX("GPION", 5, "cs", 1, GPIO_ACTIVE_LOW),
+		{ },
+	},
+};
+
 static void __init crag6410_machine_init(void)
 {
 	/* Open drain IRQs need pullups */
@@ -856,7 +865,9 @@ static void __init crag6410_machine_init(void)
 	i2c_register_board_info(1, i2c_devs1, ARRAY_SIZE(i2c_devs1));
 
 	samsung_keypad_set_platdata(&crag6410_keypad_data);
-	s3c64xx_spi0_set_platdata(NULL, 0, 2);
+
+	gpiod_add_lookup_table(&crag_spi0_gpiod_table);
+	s3c64xx_spi0_set_platdata(0, 2);
 
 	pwm_add_table(crag6410_pwm_lookup, ARRAY_SIZE(crag6410_pwm_lookup));
 	platform_add_devices(crag6410_devices, ARRAY_SIZE(crag6410_devices));
diff --git a/arch/arm/mach-s3c/mach-gta02.c b/arch/arm/mach-s3c/mach-gta02.c
index 418939ce0fc3..d50a81d85ae1 100644
--- a/arch/arm/mach-s3c/mach-gta02.c
+++ b/arch/arm/mach-s3c/mach-gta02.c
@@ -421,7 +421,14 @@ static struct s3c2410_platform_nand __initdata gta02_nand_info = {
 /* Get PMU to set USB current limit accordingly. */
 static struct s3c2410_udc_mach_info gta02_udc_cfg __initdata = {
 	.vbus_draw	= gta02_udc_vbus_draw,
-	.pullup_pin = GTA02_GPIO_USB_PULLUP,
+};
+
+static struct gpiod_lookup_table gta02_udc_gpio_table = {
+	.dev_id = "s3c2410-usbgadget",
+	.table = {
+		GPIO_LOOKUP("GPIOB", 9, "pullup", GPIO_ACTIVE_HIGH),
+		{ },
+	},
 };
 
 /* USB */
@@ -555,6 +562,7 @@ static void __init gta02_machine_init(void)
 	s3c_gpio_cfgall_range(S3C2410_GPE(0), 5, S3C_GPIO_SFN(2),
 			      S3C_GPIO_PULL_NONE);
 
+	gpiod_add_lookup_table(&gta02_udc_gpio_table);
 	gpiod_add_lookup_table(&gta02_audio_gpio_table);
 	gpiod_add_lookup_table(&gta02_mmc_gpio_table);
 	platform_add_devices(gta02_devices, ARRAY_SIZE(gta02_devices));
@@ -572,6 +580,7 @@ static void __init gta02_init_time(void)
 MACHINE_START(NEO1973_GTA02, "GTA02")
 	/* Maintainer: Nelson Castillo <arhuaco@freaks-unidos.net> */
 	.atag_offset	= 0x100,
+	.nr_irqs	= NR_IRQS_S3C2442,
 	.map_io		= gta02_map_io,
 	.init_irq	= s3c2442_init_irq,
 	.init_machine	= gta02_machine_init,
diff --git a/arch/arm/mach-s3c/mach-h1940.c b/arch/arm/mach-s3c/mach-h1940.c
index 8a43ed1c4c4d..83ac6cfdb1d8 100644
--- a/arch/arm/mach-s3c/mach-h1940.c
+++ b/arch/arm/mach-s3c/mach-h1940.c
@@ -167,9 +167,15 @@ static struct gpio_chip h1940_latch_gpiochip = {
 };
 
 static struct s3c2410_udc_mach_info h1940_udc_cfg __initdata = {
-	.vbus_pin		= S3C2410_GPG(5),
-	.vbus_pin_inverted	= 1,
-	.pullup_pin		= H1940_LATCH_USB_DP,
+};
+
+static struct gpiod_lookup_table h1940_udc_gpio_table = {
+	.dev_id = "s3c2410-usbgadget",
+	.table = {
+		GPIO_LOOKUP("GPIOG", 5, "vbus", GPIO_ACTIVE_LOW),
+		GPIO_LOOKUP("H1940_LATCH", 7, "pullup", GPIO_ACTIVE_HIGH),
+		{ },
+	},
 };
 
 static struct s3c2410_ts_mach_info h1940_ts_cfg __initdata = {
@@ -725,6 +731,7 @@ static void __init h1940_init(void)
 	u32 tmp;
 
 	s3c24xx_fb_set_platdata(&h1940_fb_info);
+	gpiod_add_lookup_table(&h1940_udc_gpio_table);
 	gpiod_add_lookup_table(&h1940_mmc_gpio_table);
 	gpiod_add_lookup_table(&h1940_audio_gpio_table);
 	gpiod_add_lookup_table(&h1940_bat_gpio_table);
@@ -793,6 +800,7 @@ static void __init h1940_init(void)
 MACHINE_START(H1940, "IPAQ-H1940")
 	/* Maintainer: Ben Dooks <ben-linux@fluff.org> */
 	.atag_offset	= 0x100,
+	.nr_irqs	= NR_IRQS_S3C2410,
 	.map_io		= h1940_map_io,
 	.reserve	= h1940_reserve,
 	.init_irq	= s3c2410_init_irq,
diff --git a/arch/arm/mach-s3c/mach-hmt.c b/arch/arm/mach-s3c/mach-hmt.c
index b287e9987311..49ba16c447aa 100644
--- a/arch/arm/mach-s3c/mach-hmt.c
+++ b/arch/arm/mach-s3c/mach-hmt.c
@@ -26,7 +26,7 @@
 
 #include <video/samsung_fimd.h>
 #include "map.h"
-#include <mach/irqs.h>
+#include "irqs.h"
 
 #include <asm/irq.h>
 #include <asm/mach-types.h>
diff --git a/arch/arm/mach-s3c/mach-jive.c b/arch/arm/mach-s3c/mach-jive.c
index 0785638a9069..16859bb3bb13 100644
--- a/arch/arm/mach-s3c/mach-jive.c
+++ b/arch/arm/mach-s3c/mach-jive.c
@@ -236,17 +236,18 @@ static int __init jive_mtdset(char *options)
 	unsigned long set;
 
 	if (options == NULL || options[0] == '\0')
-		return 0;
+		return 1;
 
 	if (kstrtoul(options, 10, &set)) {
 		printk(KERN_ERR "failed to parse mtdset=%s\n", options);
-		return 0;
+		return 1;
 	}
 
 	switch (set) {
 	case 1:
 		nand->nr_partitions = ARRAY_SIZE(jive_imageB_nand_part);
 		nand->partitions = jive_imageB_nand_part;
+		break;
 	case 0:
 		/* this is already setup in the nand info */
 		break;
@@ -255,7 +256,7 @@ static int __init jive_mtdset(char *options)
 		       "using default.", set);
 	}
 
-	return 0;
+	return 1;
 }
 
 /* parse the mtdset= option given to the kernel command line */
@@ -492,7 +493,14 @@ static struct platform_device *jive_devices[] __initdata = {
 };
 
 static struct s3c2410_udc_mach_info jive_udc_cfg __initdata = {
-	.vbus_pin	= S3C2410_GPG(1),		/* detect is on GPG1 */
+};
+
+static struct gpiod_lookup_table jive_udc_gpio_table = {
+	.dev_id = "s3c2410-usbgadget",
+	.table = {
+		GPIO_LOOKUP("GPIOG", 1, "vbus", GPIO_ACTIVE_HIGH),
+		{ },
+	},
 };
 
 /* Jive power management device */
@@ -668,6 +676,7 @@ static void __init jive_machine_init(void)
 
 	pm_power_off = jive_power_off;
 
+	gpiod_add_lookup_table(&jive_udc_gpio_table);
 	gpiod_add_lookup_table(&jive_lcdspi_gpiod_table);
 	gpiod_add_lookup_table(&jive_wm8750_gpiod_table);
 	platform_add_devices(jive_devices, ARRAY_SIZE(jive_devices));
@@ -676,7 +685,7 @@ static void __init jive_machine_init(void)
 MACHINE_START(JIVE, "JIVE")
 	/* Maintainer: Ben Dooks <ben-linux@fluff.org> */
 	.atag_offset	= 0x100,
-
+	.nr_irqs	= NR_IRQS_S3C2412,
 	.init_irq	= s3c2412_init_irq,
 	.map_io		= jive_map_io,
 	.init_machine	= jive_machine_init,
diff --git a/arch/arm/mach-s3c/mach-mini2440.c b/arch/arm/mach-s3c/mach-mini2440.c
index 551ec660ab59..283be70ca622 100644
--- a/arch/arm/mach-s3c/mach-mini2440.c
+++ b/arch/arm/mach-s3c/mach-mini2440.c
@@ -35,7 +35,7 @@
 
 #include "regs-gpio.h"
 #include <linux/platform_data/leds-s3c24xx.h>
-#include <mach/irqs.h>
+#include "irqs.h"
 #include "gpio-samsung.h"
 #include <linux/platform_data/mtd-nand-s3c2410.h>
 #include <linux/platform_data/i2c-s3c2410.h>
@@ -93,9 +93,15 @@ static struct s3c2410_uartcfg mini2440_uartcfgs[] __initdata = {
 /* USB device UDC support */
 
 static struct s3c2410_udc_mach_info mini2440_udc_cfg __initdata = {
-	.pullup_pin = S3C2410_GPC(5),
 };
 
+static struct gpiod_lookup_table mini2440_udc_gpio_table = {
+	.dev_id = "s3c2410-usbgadget",
+	.table = {
+		GPIO_LOOKUP("GPIOC", 5, "pullup", GPIO_ACTIVE_HIGH),
+		{ },
+	},
+};
 
 /* LCD timing and setup */
 
@@ -624,7 +630,7 @@ static char mini2440_features_str[12] __initdata = "0tb";
 static int __init mini2440_features_setup(char *str)
 {
 	if (str)
-		strlcpy(mini2440_features_str, str,
+		strscpy(mini2440_features_str, str,
 			sizeof(mini2440_features_str));
 	return 1;
 }
@@ -755,6 +761,7 @@ static void __init mini2440_init(void)
 		s3c24xx_fb_set_platdata(&mini2440_fb_info);
 	}
 
+	gpiod_add_lookup_table(&mini2440_udc_gpio_table);
 	s3c24xx_udc_set_platdata(&mini2440_udc_cfg);
 	gpiod_add_lookup_table(&mini2440_mmc_gpio_table);
 	s3c24xx_mci_set_platdata(&mini2440_mmc_cfg);
@@ -789,6 +796,7 @@ static void __init mini2440_init(void)
 MACHINE_START(MINI2440, "MINI2440")
 	/* Maintainer: Michel Pollet <buserror@gmail.com> */
 	.atag_offset	= 0x100,
+	.nr_irqs	= NR_IRQS_S3C2440,
 	.map_io		= mini2440_map_io,
 	.init_machine	= mini2440_init,
 	.init_irq	= s3c2440_init_irq,
diff --git a/arch/arm/mach-s3c/mach-mini6410.c b/arch/arm/mach-s3c/mach-mini6410.c
index c14c2e27127b..058ae9e8b89f 100644
--- a/arch/arm/mach-s3c/mach-mini6410.c
+++ b/arch/arm/mach-s3c/mach-mini6410.c
@@ -35,7 +35,7 @@
 #include <linux/platform_data/mmc-sdhci-s3c.h>
 #include "sdhci.h"
 #include <linux/platform_data/touchscreen-s3c2410.h>
-#include <mach/irqs.h>
+#include "irqs.h"
 
 #include <video/platform_lcd.h>
 #include <video/samsung_fimd.h>
diff --git a/arch/arm/mach-s3c/mach-n30.c b/arch/arm/mach-s3c/mach-n30.c
index e40c1fcf418c..90122fc6b2aa 100644
--- a/arch/arm/mach-s3c/mach-n30.c
+++ b/arch/arm/mach-s3c/mach-n30.c
@@ -84,9 +84,15 @@ static struct s3c2410_uartcfg n30_uartcfgs[] = {
 };
 
 static struct s3c2410_udc_mach_info n30_udc_cfg __initdata = {
-	.vbus_pin		= S3C2410_GPG(1),
-	.vbus_pin_inverted	= 0,
-	.pullup_pin		= S3C2410_GPB(3),
+};
+
+static struct gpiod_lookup_table n30_udc_gpio_table = {
+	.dev_id = "s3c2410-usbgadget",
+	.table = {
+		GPIO_LOOKUP("GPIOG", 1, "vbus", GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP("GPIOB", 3, "pullup", GPIO_ACTIVE_HIGH),
+		{ },
+	},
 };
 
 static struct gpio_keys_button n30_buttons[] = {
@@ -595,6 +601,7 @@ static void __init n30_init(void)
 	WARN_ON(gpio_request(S3C2410_GPG(4), "mmc power"));
 
 	s3c24xx_fb_set_platdata(&n30_fb_info);
+	gpiod_add_lookup_table(&n30_udc_gpio_table);
 	s3c24xx_udc_set_platdata(&n30_udc_cfg);
 	gpiod_add_lookup_table(&n30_mci_gpio_table);
 	s3c24xx_mci_set_platdata(&n30_mci_cfg);
@@ -656,6 +663,7 @@ MACHINE_START(N30, "Acer-N30")
 				Ben Dooks <ben-linux@fluff.org>
 	*/
 	.atag_offset	= 0x100,
+	.nr_irqs	= NR_IRQS_S3C2410,
 	.init_time	= n30_init_time,
 	.init_machine	= n30_init,
 	.init_irq	= s3c2410_init_irq,
@@ -666,6 +674,7 @@ MACHINE_START(N35, "Acer-N35")
 	/* Maintainer: Christer Weinigel <christer@weinigel.se>
 	*/
 	.atag_offset	= 0x100,
+	.nr_irqs	= NR_IRQS_S3C2410,
 	.init_time	= n30_init_time,
 	.init_machine	= n30_init,
 	.init_irq	= s3c2410_init_irq,
diff --git a/arch/arm/mach-s3c/mach-ncp.c b/arch/arm/mach-s3c/mach-ncp.c
index 1a45bed56622..1e65f8bce5c4 100644
--- a/arch/arm/mach-s3c/mach-ncp.c
+++ b/arch/arm/mach-s3c/mach-ncp.c
@@ -24,7 +24,7 @@
 #include <asm/mach/map.h>
 #include <asm/mach/irq.h>
 
-#include <mach/irqs.h>
+#include "irqs.h"
 #include "map.h"
 
 #include <asm/irq.h>
diff --git a/arch/arm/mach-s3c/mach-nexcoder.c b/arch/arm/mach-s3c/mach-nexcoder.c
index 2a454c919658..d17a3fcb7425 100644
--- a/arch/arm/mach-s3c/mach-nexcoder.c
+++ b/arch/arm/mach-s3c/mach-nexcoder.c
@@ -154,6 +154,7 @@ static void __init nexcoder_init(void)
 MACHINE_START(NEXCODER_2440, "NexVision - Nexcoder 2440")
 	/* Maintainer: Guillaume GOURAT <guillaume.gourat@nexvision.tv> */
 	.atag_offset	= 0x100,
+	.nr_irqs	= NR_IRQS_S3C2440,
 	.map_io		= nexcoder_map_io,
 	.init_machine	= nexcoder_init,
 	.init_irq	= s3c2440_init_irq,
diff --git a/arch/arm/mach-s3c/mach-osiris.c b/arch/arm/mach-s3c/mach-osiris.c
index 3aefb9d22340..d900d1354de1 100644
--- a/arch/arm/mach-s3c/mach-osiris.c
+++ b/arch/arm/mach-s3c/mach-osiris.c
@@ -58,11 +58,6 @@ static struct map_desc osiris_iodesc[] __initdata = {
 	  .pfn		= __phys_to_pfn(S3C2410_CS5),
 	  .length	= SZ_16M,
 	  .type		= MT_DEVICE,
-  }, {
-	  .virtual	= (u32)S3C24XX_VA_ISA_WORD,
-	  .pfn		= __phys_to_pfn(S3C2410_CS5),
-	  .length	= SZ_16M,
-	  .type		= MT_DEVICE,
   },
 
   /* CPLD control registers */
@@ -402,6 +397,7 @@ static void __init osiris_init(void)
 MACHINE_START(OSIRIS, "Simtec-OSIRIS")
 	/* Maintainer: Ben Dooks <ben@simtec.co.uk> */
 	.atag_offset	= 0x100,
+	.nr_irqs	= NR_IRQS_S3C2440,
 	.map_io		= osiris_map_io,
 	.init_irq	= s3c2440_init_irq,
 	.init_machine	= osiris_init,
diff --git a/arch/arm/mach-s3c/mach-otom.c b/arch/arm/mach-s3c/mach-otom.c
index 460ee97766cd..3a2db2f58833 100644
--- a/arch/arm/mach-s3c/mach-otom.c
+++ b/arch/arm/mach-s3c/mach-otom.c
@@ -116,6 +116,7 @@ static void __init otom11_init(void)
 MACHINE_START(OTOM, "Nex Vision - Otom 1.1")
 	/* Maintainer: Guillaume GOURAT <guillaume.gourat@nexvision.tv> */
 	.atag_offset	= 0x100,
+	.nr_irqs	= NR_IRQS_S3C2410,
 	.map_io		= otom11_map_io,
 	.init_machine	= otom11_init,
 	.init_irq	= s3c2410_init_irq,
diff --git a/arch/arm/mach-s3c/mach-qt2410.c b/arch/arm/mach-s3c/mach-qt2410.c
index f88b961798fd..36fe0684a438 100644
--- a/arch/arm/mach-s3c/mach-qt2410.c
+++ b/arch/arm/mach-s3c/mach-qt2410.c
@@ -367,6 +367,7 @@ static void __init qt2410_machine_init(void)
 
 MACHINE_START(QT2410, "QT2410")
 	.atag_offset	= 0x100,
+	.nr_irqs	= NR_IRQS_S3C2410,
 	.map_io		= qt2410_map_io,
 	.init_irq	= s3c2410_init_irq,
 	.init_machine	= qt2410_machine_init,
diff --git a/arch/arm/mach-s3c/mach-real6410.c b/arch/arm/mach-s3c/mach-real6410.c
index 9d218a53d631..8c10ebc38a9c 100644
--- a/arch/arm/mach-s3c/mach-real6410.c
+++ b/arch/arm/mach-s3c/mach-real6410.c
@@ -27,7 +27,7 @@
 #include "map.h"
 #include "regs-gpio.h"
 #include "gpio-samsung.h"
-#include <mach/irqs.h>
+#include "irqs.h"
 
 #include <linux/soc/samsung/s3c-adc.h>
 #include "cpu.h"
diff --git a/arch/arm/mach-s3c/mach-rx1950.c b/arch/arm/mach-s3c/mach-rx1950.c
index 313e080e179e..d8c49e562660 100644
--- a/arch/arm/mach-s3c/mach-rx1950.c
+++ b/arch/arm/mach-s3c/mach-rx1950.c
@@ -643,9 +643,15 @@ static struct s3c2410_platform_nand rx1950_nand_info = {
 };
 
 static struct s3c2410_udc_mach_info rx1950_udc_cfg __initdata = {
-	.vbus_pin = S3C2410_GPG(5),
-	.vbus_pin_inverted = 1,
-	.pullup_pin = S3C2410_GPJ(5),
+};
+
+static struct gpiod_lookup_table rx1950_udc_gpio_table = {
+	.dev_id = "s3c2410-usbgadget",
+	.table = {
+		GPIO_LOOKUP("GPIOG", 5, "vbus", GPIO_ACTIVE_LOW),
+		GPIO_LOOKUP("GPIOJ", 5, "pullup", GPIO_ACTIVE_HIGH),
+		{ },
+	},
 };
 
 static struct s3c2410_ts_mach_info rx1950_ts_cfg __initdata = {
@@ -847,6 +853,7 @@ static void __init rx1950_init_machine(void)
 	gpio_direction_output(S3C2410_GPJ(6), 0);
 
 	pwm_add_table(rx1950_pwm_lookup, ARRAY_SIZE(rx1950_pwm_lookup));
+	gpiod_add_lookup_table(&rx1950_udc_gpio_table);
 	gpiod_add_lookup_table(&rx1950_audio_gpio_table);
 	gpiod_add_lookup_table(&rx1950_bat_gpio_table);
 	/* Configure the I2S pins (GPE0...GPE4) in correct mode */
@@ -868,6 +875,7 @@ static void __init rx1950_reserve(void)
 MACHINE_START(RX1950, "HP iPAQ RX1950")
     /* Maintainers: Vasily Khoruzhick */
 	.atag_offset = 0x100,
+	.nr_irqs	= NR_IRQS_S3C2442,
 	.map_io = rx1950_map_io,
 	.reserve	= rx1950_reserve,
 	.init_irq	= s3c2442_init_irq,
diff --git a/arch/arm/mach-s3c/mach-rx3715.c b/arch/arm/mach-s3c/mach-rx3715.c
index 9fd2d9dc3689..52b3c38acbb2 100644
--- a/arch/arm/mach-s3c/mach-rx3715.c
+++ b/arch/arm/mach-s3c/mach-rx3715.c
@@ -48,13 +48,7 @@
 
 static struct map_desc rx3715_iodesc[] __initdata = {
 	/* dump ISA space somewhere unused */
-
 	{
-		.virtual	= (u32)S3C24XX_VA_ISA_WORD,
-		.pfn		= __phys_to_pfn(S3C2410_CS3),
-		.length		= SZ_1M,
-		.type		= MT_DEVICE,
-	}, {
 		.virtual	= (u32)S3C24XX_VA_ISA_BYTE,
 		.pfn		= __phys_to_pfn(S3C2410_CS3),
 		.length		= SZ_1M,
@@ -210,6 +204,7 @@ static void __init rx3715_init_machine(void)
 MACHINE_START(RX3715, "IPAQ-RX3715")
 	/* Maintainer: Ben Dooks <ben-linux@fluff.org> */
 	.atag_offset	= 0x100,
+	.nr_irqs	= NR_IRQS_S3C2440,
 	.map_io		= rx3715_map_io,
 	.reserve	= rx3715_reserve,
 	.init_irq	= s3c2440_init_irq,
diff --git a/arch/arm/mach-s3c/mach-smartq5.c b/arch/arm/mach-s3c/mach-smartq5.c
index 8c940227e810..ce3fce0bba20 100644
--- a/arch/arm/mach-s3c/mach-smartq5.c
+++ b/arch/arm/mach-s3c/mach-smartq5.c
@@ -14,7 +14,7 @@
 #include <asm/mach/arch.h>
 
 #include <video/samsung_fimd.h>
-#include <mach/irqs.h>
+#include "irqs.h"
 #include "map.h"
 #include "regs-gpio.h"
 #include "gpio-samsung.h"
diff --git a/arch/arm/mach-s3c/mach-smartq7.c b/arch/arm/mach-s3c/mach-smartq7.c
index ab243969d6d0..78ca0e704797 100644
--- a/arch/arm/mach-s3c/mach-smartq7.c
+++ b/arch/arm/mach-s3c/mach-smartq7.c
@@ -14,7 +14,7 @@
 #include <asm/mach/arch.h>
 
 #include <video/samsung_fimd.h>
-#include <mach/irqs.h>
+#include "irqs.h"
 #include "map.h"
 #include "regs-gpio.h"
 #include "gpio-samsung.h"
diff --git a/arch/arm/mach-s3c/mach-smdk2410.c b/arch/arm/mach-s3c/mach-smdk2410.c
index ca83d5a7d101..76b0a8846616 100644
--- a/arch/arm/mach-s3c/mach-smdk2410.c
+++ b/arch/arm/mach-s3c/mach-smdk2410.c
@@ -104,6 +104,7 @@ MACHINE_START(SMDK2410, "SMDK2410") /* @TODO: request a new identifier and switc
 				    * to SMDK2410 */
 	/* Maintainer: Jonas Dietsche */
 	.atag_offset	= 0x100,
+	.nr_irqs	= NR_IRQS_S3C2410,
 	.map_io		= smdk2410_map_io,
 	.init_irq	= s3c2410_init_irq,
 	.init_machine	= smdk2410_init,
diff --git a/arch/arm/mach-s3c/mach-smdk2413.c b/arch/arm/mach-s3c/mach-smdk2413.c
index c43095b321d7..2b4e20aaa346 100644
--- a/arch/arm/mach-s3c/mach-smdk2413.c
+++ b/arch/arm/mach-s3c/mach-smdk2413.c
@@ -12,7 +12,7 @@
 #include <linux/list.h>
 #include <linux/timer.h>
 #include <linux/init.h>
-#include <linux/gpio.h>
+#include <linux/gpio/machine.h>
 #include <linux/serial_core.h>
 #include <linux/serial_s3c.h>
 #include <linux/platform_device.h>
@@ -74,9 +74,15 @@ static struct s3c2410_uartcfg smdk2413_uartcfgs[] __initdata = {
 
 
 static struct s3c2410_udc_mach_info smdk2413_udc_cfg __initdata = {
-	.pullup_pin = S3C2410_GPF(2),
 };
 
+static struct gpiod_lookup_table smdk2413_udc_gpio_table = {
+	.dev_id = "s3c2410-usbgadget",
+	.table = {
+		GPIO_LOOKUP("GPIOF", 2, "pullup", GPIO_ACTIVE_HIGH),
+		{ },
+	},
+};
 
 static struct platform_device *smdk2413_devices[] __initdata = {
 	&s3c_device_ohci,
@@ -115,7 +121,7 @@ static void __init smdk2413_machine_init(void)
 			      S3C2410_MISCCR_USBSUSPND0 |
 			      S3C2410_MISCCR_USBSUSPND1, 0x0);
 
-
+	gpiod_add_lookup_table(&smdk2413_udc_gpio_table);
  	s3c24xx_udc_set_platdata(&smdk2413_udc_cfg);
 	s3c_i2c0_set_platdata(NULL);
 	/* Configure the I2S pins (GPE0...GPE4) in correct mode */
@@ -129,6 +135,7 @@ static void __init smdk2413_machine_init(void)
 MACHINE_START(S3C2413, "S3C2413")
 	/* Maintainer: Ben Dooks <ben-linux@fluff.org> */
 	.atag_offset	= 0x100,
+	.nr_irqs	= NR_IRQS_S3C2412,
 
 	.fixup		= smdk2413_fixup,
 	.init_irq	= s3c2412_init_irq,
@@ -140,6 +147,7 @@ MACHINE_END
 MACHINE_START(SMDK2412, "SMDK2412")
 	/* Maintainer: Ben Dooks <ben-linux@fluff.org> */
 	.atag_offset	= 0x100,
+	.nr_irqs	= NR_IRQS_S3C2412,
 
 	.fixup		= smdk2413_fixup,
 	.init_irq	= s3c2412_init_irq,
@@ -151,6 +159,7 @@ MACHINE_END
 MACHINE_START(SMDK2413, "SMDK2413")
 	/* Maintainer: Ben Dooks <ben-linux@fluff.org> */
 	.atag_offset	= 0x100,
+	.nr_irqs	= NR_IRQS_S3C2412,
 
 	.fixup		= smdk2413_fixup,
 	.init_irq	= s3c2412_init_irq,
diff --git a/arch/arm/mach-s3c/mach-smdk2416.c b/arch/arm/mach-s3c/mach-smdk2416.c
index 4d883a792cc6..329fe26be268 100644
--- a/arch/arm/mach-s3c/mach-smdk2416.c
+++ b/arch/arm/mach-s3c/mach-smdk2416.c
@@ -53,16 +53,6 @@ static struct map_desc smdk2416_iodesc[] __initdata = {
 	/* ISA IO Space map (memory space selected by A24) */
 
 	{
-		.virtual	= (u32)S3C24XX_VA_ISA_WORD,
-		.pfn		= __phys_to_pfn(S3C2410_CS2),
-		.length		= 0x10000,
-		.type		= MT_DEVICE,
-	}, {
-		.virtual	= (u32)S3C24XX_VA_ISA_WORD + 0x10000,
-		.pfn		= __phys_to_pfn(S3C2410_CS2 + (1<<24)),
-		.length		= SZ_4M,
-		.type		= MT_DEVICE,
-	}, {
 		.virtual	= (u32)S3C24XX_VA_ISA_BYTE,
 		.pfn		= __phys_to_pfn(S3C2410_CS2),
 		.length		= 0x10000,
@@ -249,6 +239,7 @@ static void __init smdk2416_machine_init(void)
 MACHINE_START(SMDK2416, "SMDK2416")
 	/* Maintainer: Yauhen Kharuzhy <jekhor@gmail.com> */
 	.atag_offset	= 0x100,
+	.nr_irqs	= NR_IRQS_S3C2416,
 
 	.init_irq	= s3c2416_init_irq,
 	.map_io		= smdk2416_map_io,
diff --git a/arch/arm/mach-s3c/mach-smdk2440.c b/arch/arm/mach-s3c/mach-smdk2440.c
index 7f6fe0db04f3..6aea769ebde1 100644
--- a/arch/arm/mach-s3c/mach-smdk2440.c
+++ b/arch/arm/mach-s3c/mach-smdk2440.c
@@ -43,16 +43,6 @@ static struct map_desc smdk2440_iodesc[] __initdata = {
 	/* ISA IO Space map (memory space selected by A24) */
 
 	{
-		.virtual	= (u32)S3C24XX_VA_ISA_WORD,
-		.pfn		= __phys_to_pfn(S3C2410_CS2),
-		.length		= 0x10000,
-		.type		= MT_DEVICE,
-	}, {
-		.virtual	= (u32)S3C24XX_VA_ISA_WORD + 0x10000,
-		.pfn		= __phys_to_pfn(S3C2410_CS2 + (1<<24)),
-		.length		= SZ_4M,
-		.type		= MT_DEVICE,
-	}, {
 		.virtual	= (u32)S3C24XX_VA_ISA_BYTE,
 		.pfn		= __phys_to_pfn(S3C2410_CS2),
 		.length		= 0x10000,
@@ -181,6 +171,7 @@ static void __init smdk2440_machine_init(void)
 MACHINE_START(S3C2440, "SMDK2440")
 	/* Maintainer: Ben Dooks <ben-linux@fluff.org> */
 	.atag_offset	= 0x100,
+	.nr_irqs	= NR_IRQS_S3C2440,
 
 	.init_irq	= s3c2440_init_irq,
 	.map_io		= smdk2440_map_io,
diff --git a/arch/arm/mach-s3c/mach-smdk2443.c b/arch/arm/mach-s3c/mach-smdk2443.c
index fc54c91ade56..075140f8f760 100644
--- a/arch/arm/mach-s3c/mach-smdk2443.c
+++ b/arch/arm/mach-s3c/mach-smdk2443.c
@@ -40,16 +40,6 @@ static struct map_desc smdk2443_iodesc[] __initdata = {
 	/* ISA IO Space map (memory space selected by A24) */
 
 	{
-		.virtual	= (u32)S3C24XX_VA_ISA_WORD,
-		.pfn		= __phys_to_pfn(S3C2410_CS2),
-		.length		= 0x10000,
-		.type		= MT_DEVICE,
-	}, {
-		.virtual	= (u32)S3C24XX_VA_ISA_WORD + 0x10000,
-		.pfn		= __phys_to_pfn(S3C2410_CS2 + (1<<24)),
-		.length		= SZ_4M,
-		.type		= MT_DEVICE,
-	}, {
 		.virtual	= (u32)S3C24XX_VA_ISA_BYTE,
 		.pfn		= __phys_to_pfn(S3C2410_CS2),
 		.length		= 0x10000,
@@ -128,7 +118,7 @@ static void __init smdk2443_machine_init(void)
 MACHINE_START(SMDK2443, "SMDK2443")
 	/* Maintainer: Ben Dooks <ben-linux@fluff.org> */
 	.atag_offset	= 0x100,
-
+	.nr_irqs	= NR_IRQS_S3C2443,
 	.init_irq	= s3c2443_init_irq,
 	.map_io		= smdk2443_map_io,
 	.init_machine	= smdk2443_machine_init,
diff --git a/arch/arm/mach-s3c/mach-smdk6400.c b/arch/arm/mach-s3c/mach-smdk6400.c
index 827221398d6c..a3c1b2a82455 100644
--- a/arch/arm/mach-s3c/mach-smdk6400.c
+++ b/arch/arm/mach-s3c/mach-smdk6400.c
@@ -22,7 +22,7 @@
 #include <asm/mach/map.h>
 #include <asm/mach/irq.h>
 
-#include <mach/irqs.h>
+#include "irqs.h"
 #include "map.h"
 
 #include "devs.h"
diff --git a/arch/arm/mach-s3c/mach-smdk6410.c b/arch/arm/mach-s3c/mach-smdk6410.c
index ae18c1375c9c..e57b2bb61484 100644
--- a/arch/arm/mach-s3c/mach-smdk6410.c
+++ b/arch/arm/mach-s3c/mach-smdk6410.c
@@ -45,7 +45,7 @@
 #include <asm/mach/map.h>
 #include <asm/mach/irq.h>
 
-#include <mach/irqs.h>
+#include "irqs.h"
 #include "map.h"
 
 #include <asm/irq.h>
diff --git a/arch/arm/mach-s3c/mach-tct_hammer.c b/arch/arm/mach-s3c/mach-tct_hammer.c
index 2a61df316e8c..93ab1abd8bd3 100644
--- a/arch/arm/mach-s3c/mach-tct_hammer.c
+++ b/arch/arm/mach-s3c/mach-tct_hammer.c
@@ -149,6 +149,7 @@ static void __init tct_hammer_init(void)
 
 MACHINE_START(TCT_HAMMER, "TCT_HAMMER")
 	.atag_offset	= 0x100,
+	.nr_irqs	= NR_IRQS_S3C2410,
 	.map_io		= tct_hammer_map_io,
 	.init_irq	= s3c2410_init_irq,
 	.init_machine	= tct_hammer_init,
diff --git a/arch/arm/mach-s3c/mach-vr1000.c b/arch/arm/mach-s3c/mach-vr1000.c
index 5c3d07cf2e79..c85033e6ef8f 100644
--- a/arch/arm/mach-s3c/mach-vr1000.c
+++ b/arch/arm/mach-s3c/mach-vr1000.c
@@ -67,11 +67,6 @@ static struct map_desc vr1000_iodesc[] __initdata = {
 	  .pfn		= PA_CS2(BAST_PA_ISAIO),
 	  .length	= SZ_16M,
 	  .type		= MT_DEVICE,
-  }, {
-	  .virtual	= (u32)S3C24XX_VA_ISA_WORD,
-	  .pfn		= PA_CS3(BAST_PA_ISAIO),
-	  .length	= SZ_16M,
-	  .type		= MT_DEVICE,
   },
 
   /*  CPLD control registers, and external interrupt controls */
@@ -361,6 +356,7 @@ static void __init vr1000_init(void)
 MACHINE_START(VR1000, "Thorcom-VR1000")
 	/* Maintainer: Ben Dooks <ben@simtec.co.uk> */
 	.atag_offset	= 0x100,
+	.nr_irqs	= NR_IRQS_S3C2410,
 	.map_io		= vr1000_map_io,
 	.init_machine	= vr1000_init,
 	.init_irq	= s3c2410_init_irq,
diff --git a/arch/arm/mach-s3c/mach-vstms.c b/arch/arm/mach-s3c/mach-vstms.c
index ec024af7b0ce..6f878418be3e 100644
--- a/arch/arm/mach-s3c/mach-vstms.c
+++ b/arch/arm/mach-s3c/mach-vstms.c
@@ -156,6 +156,7 @@ static void __init vstms_init(void)
 
 MACHINE_START(VSTMS, "VSTMS")
 	.atag_offset	= 0x100,
+	.nr_irqs	= NR_IRQS_S3C2412,
 
 	.fixup		= vstms_fixup,
 	.init_irq	= s3c2412_init_irq,
diff --git a/arch/arm/mach-s3c/include/mach/map-base.h b/arch/arm/mach-s3c/map-base.h
index 34b39ded0e2e..463a995b399b 100644
--- a/arch/arm/mach-s3c/include/mach/map-base.h
+++ b/arch/arm/mach-s3c/map-base.h
@@ -33,6 +33,12 @@
 #define S3C_VA_WATCHDOG	S3C_ADDR(0x00400000)	/* watchdog */
 #define S3C_VA_UART	S3C_ADDR(0x01000000)	/* UART */
 
+/* ISA device mapping for BAST to use with inb()/outb() on 8-bit I/O.
+ * 16-bit I/O on BAST now requires driver modifications to manually
+ * ioremap CS3.
+ */
+#define S3C24XX_VA_ISA_BYTE	PCI_IOBASE
+
 /* This is used for the CPU specific mappings that may be needed, so that
  * they do not need to directly used S3C_ADDR() and thus make it easier to
  * modify the space for mapping.
diff --git a/arch/arm/mach-s3c/map-s3c24xx.h b/arch/arm/mach-s3c/map-s3c24xx.h
index b5dba78a9dd7..f8d075b11d6f 100644
--- a/arch/arm/mach-s3c/map-s3c24xx.h
+++ b/arch/arm/mach-s3c/map-s3c24xx.h
@@ -9,7 +9,7 @@
 #ifndef __ASM_ARCH_MAP_H
 #define __ASM_ARCH_MAP_H
 
-#include <mach/map-base.h>
+#include "map-base.h"
 #include "map-s3c.h"
 
 /*
diff --git a/arch/arm/mach-s3c/map-s3c64xx.h b/arch/arm/mach-s3c/map-s3c64xx.h
index d7740d2a77c4..9de1c58bcb06 100644
--- a/arch/arm/mach-s3c/map-s3c64xx.h
+++ b/arch/arm/mach-s3c/map-s3c64xx.h
@@ -11,7 +11,7 @@
 #ifndef __ASM_ARCH_MAP_H
 #define __ASM_ARCH_MAP_H __FILE__
 
-#include <mach/map-base.h>
+#include "map-base.h"
 #include "map-s3c.h"
 
 /*
diff --git a/arch/arm/mach-s3c/pl080.c b/arch/arm/mach-s3c/pl080.c
index 4730f080c736..0a14f77b24c1 100644
--- a/arch/arm/mach-s3c/pl080.c
+++ b/arch/arm/mach-s3c/pl080.c
@@ -11,7 +11,7 @@
 #include <linux/of.h>
 
 #include "cpu.h"
-#include <mach/irqs.h>
+#include "irqs.h"
 #include "map.h"
 
 #include "regs-sys-s3c64xx.h"
diff --git a/arch/arm/mach-s3c/pm-core-s3c24xx.h b/arch/arm/mach-s3c/pm-core-s3c24xx.h
index bcb7978a4e85..a71ed5711019 100644
--- a/arch/arm/mach-s3c/pm-core-s3c24xx.h
+++ b/arch/arm/mach-s3c/pm-core-s3c24xx.h
@@ -12,7 +12,7 @@
 
 #include "regs-clock.h"
 #include "regs-irq-s3c24xx.h"
-#include <mach/irqs.h>
+#include "irqs.h"
 
 static inline void s3c_pm_debug_init_uart(void)
 {
diff --git a/arch/arm/mach-s3c/pm-s3c2412.c b/arch/arm/mach-s3c/pm-s3c2412.c
index 6a9604477c9e..ed3b4cfc7c0f 100644
--- a/arch/arm/mach-s3c/pm-s3c2412.c
+++ b/arch/arm/mach-s3c/pm-s3c2412.c
@@ -19,7 +19,7 @@
 #include <asm/cacheflush.h>
 #include <asm/irq.h>
 
-#include <mach/irqs.h>
+#include "irqs.h"
 #include "regs-gpio.h"
 
 #include "cpu.h"
diff --git a/arch/arm/mach-s3c/pm-s3c64xx.c b/arch/arm/mach-s3c/pm-s3c64xx.c
index 4f1778123dee..7bc7417fd803 100644
--- a/arch/arm/mach-s3c/pm-s3c64xx.c
+++ b/arch/arm/mach-s3c/pm-s3c64xx.c
@@ -15,7 +15,7 @@
 #include <linux/pm_domain.h>
 
 #include "map.h"
-#include <mach/irqs.h>
+#include "irqs.h"
 
 #include "cpu.h"
 #include "devs.h"
@@ -323,7 +323,7 @@ void s3c_pm_arch_update_uart(void __iomem *regs, struct pm_uart_save *save)
 
 	/* S3C64XX UART blocks only support level interrupts, so ensure that
 	 * when we restore unused UART blocks we force the level interrupt
-	 * settigs. */
+	 * settings. */
 	save->ucon |= S3C2410_UCON_TXILEVEL | S3C2410_UCON_RXILEVEL;
 
 	/* We have a constraint on changing the clock type of the UART
diff --git a/arch/arm/mach-s3c/pm.c b/arch/arm/mach-s3c/pm.c
index c563bb9d92be..06f019690d81 100644
--- a/arch/arm/mach-s3c/pm.c
+++ b/arch/arm/mach-s3c/pm.c
@@ -21,7 +21,7 @@
 #include "map.h"
 #include "regs-clock.h"
 #include "regs-irq.h"
-#include <mach/irqs.h>
+#include "irqs.h"
 
 #include <asm/irq.h>
 
diff --git a/arch/arm/mach-s3c/s3c2443.c b/arch/arm/mach-s3c/s3c2443.c
index 08f910144246..05c3c298b9f8 100644
--- a/arch/arm/mach-s3c/s3c2443.c
+++ b/arch/arm/mach-s3c/s3c2443.c
@@ -25,7 +25,7 @@
 
 #include "map.h"
 #include "gpio-samsung.h"
-#include <mach/irqs.h>
+#include "irqs.h"
 #include <asm/irq.h>
 #include <asm/system_misc.h>
 
diff --git a/arch/arm/mach-s3c/s3c24xx.c b/arch/arm/mach-s3c/s3c24xx.c
index ccfed48c98aa..819a95364af9 100644
--- a/arch/arm/mach-s3c/s3c24xx.c
+++ b/arch/arm/mach-s3c/s3c24xx.c
@@ -146,7 +146,7 @@ static struct map_desc s3c_iodesc[] __initdata __maybe_unused = {
 	IODESC_ENT(UART)
 };
 
-/* read cpu identificaiton code */
+/* read cpu identification code */
 
 static unsigned long s3c24xx_read_idcode_v5(void)
 {
@@ -678,3 +678,10 @@ struct platform_device s3c2410_device_dclk = {
 	},
 };
 #endif
+
+#ifndef CONFIG_COMPILE_TEST
+#pragma message "The platform is deprecated and scheduled for removal. " \
+		"Please reach to the maintainers of the platform " \
+		"and linux-samsung-soc@vger.kernel.org if you still use it." \
+		"Without such feedback, the platform will be removed after 2022."
+#endif
diff --git a/arch/arm/mach-s3c/s3c24xx.h b/arch/arm/mach-s3c/s3c24xx.h
index 5848bef5bb49..34dd4ac507e9 100644
--- a/arch/arm/mach-s3c/s3c24xx.h
+++ b/arch/arm/mach-s3c/s3c24xx.h
@@ -10,7 +10,7 @@
 #define __ARCH_ARM_MACH_S3C24XX_COMMON_H __FILE__
 
 #include <linux/reboot.h>
-#include <mach/irqs.h>
+#include "irqs.h"
 
 struct s3c2410_uartcfg;
 
diff --git a/arch/arm/mach-s3c/s3c64xx.c b/arch/arm/mach-s3c/s3c64xx.c
index 4dfb648142f2..0a8116c108fe 100644
--- a/arch/arm/mach-s3c/s3c64xx.c
+++ b/arch/arm/mach-s3c/s3c64xx.c
@@ -36,7 +36,7 @@
 #include <asm/system_misc.h>
 
 #include "map.h"
-#include <mach/irqs.h>
+#include "irqs.h"
 #include "regs-gpio.h"
 #include "gpio-samsung.h"
 
@@ -425,3 +425,10 @@ static int __init s3c64xx_init_irq_eint(void)
 	return 0;
 }
 arch_initcall(s3c64xx_init_irq_eint);
+
+#ifndef CONFIG_COMPILE_TEST
+#pragma message "The platform is deprecated and scheduled for removal. " \
+		"Please reach to the maintainers of the platform " \
+		"and linux-samsung-soc@vger.kernel.org if you still use it." \
+		"Without such feedback, the platform will be removed after 2024."
+#endif
diff --git a/arch/arm/mach-s3c/setup-spi-s3c64xx.c b/arch/arm/mach-s3c/setup-spi-s3c64xx.c
index efcf78d41585..497aff71c29c 100644
--- a/arch/arm/mach-s3c/setup-spi-s3c64xx.c
+++ b/arch/arm/mach-s3c/setup-spi-s3c64xx.c
@@ -16,12 +16,3 @@ int s3c64xx_spi0_cfg_gpio(void)
 	return 0;
 }
 #endif
-
-#ifdef CONFIG_S3C64XX_DEV_SPI1
-int s3c64xx_spi1_cfg_gpio(void)
-{
-	s3c_gpio_cfgall_range(S3C64XX_GPC(4), 3,
-				S3C_GPIO_SFN(2), S3C_GPIO_PULL_UP);
-	return 0;
-}
-#endif
diff --git a/arch/arm/mach-s3c/simtec-usb.c b/arch/arm/mach-s3c/simtec-usb.c
index 18fe0642743a..76cedb5c7373 100644
--- a/arch/arm/mach-s3c/simtec-usb.c
+++ b/arch/arm/mach-s3c/simtec-usb.c
@@ -24,7 +24,7 @@
 #include <asm/mach/irq.h>
 
 #include "gpio-samsung.h"
-#include <mach/irqs.h>
+#include "irqs.h"
 #include <asm/irq.h>
 
 #include <linux/platform_data/usb-ohci-s3c2410.h>
diff --git a/arch/arm/mach-s3c/spi-core-s3c24xx.h b/arch/arm/mach-s3c/spi-core-s3c24xx.h
index 057667469cc3..919c5fd0c9af 100644
--- a/arch/arm/mach-s3c/spi-core-s3c24xx.h
+++ b/arch/arm/mach-s3c/spi-core-s3c24xx.h
@@ -16,12 +16,6 @@ static inline void s3c24xx_spi_setname(char *name)
 #ifdef CONFIG_S3C64XX_DEV_SPI0
 	s3c64xx_device_spi0.name = name;
 #endif
-#ifdef CONFIG_S3C64XX_DEV_SPI1
-	s3c64xx_device_spi1.name = name;
-#endif
-#ifdef CONFIG_S3C64XX_DEV_SPI2
-	s3c64xx_device_spi2.name = name;
-#endif
 }
 
 #endif /* __PLAT_S3C_SPI_CORE_S3C24XX_H */
diff --git a/arch/arm/mach-s5pv210/Kconfig b/arch/arm/mach-s5pv210/Kconfig
index 5a96099af991..055de578b57f 100644
--- a/arch/arm/mach-s5pv210/Kconfig
+++ b/arch/arm/mach-s5pv210/Kconfig
@@ -12,7 +12,6 @@ config ARCH_S5PV210
 	select CLKSRC_SAMSUNG_PWM
 	select COMMON_CLK_SAMSUNG
 	select GPIOLIB
-	select HAVE_S3C2410_I2C if I2C
 	select PINCTRL
 	select PINCTRL_EXYNOS
 	select SOC_SAMSUNG
diff --git a/arch/arm/mach-sa1100/Kconfig b/arch/arm/mach-sa1100/Kconfig
index 66e79fa9ba2b..fb9cd10705de 100644
--- a/arch/arm/mach-sa1100/Kconfig
+++ b/arch/arm/mach-sa1100/Kconfig
@@ -1,7 +1,25 @@
 # SPDX-License-Identifier: GPL-2.0-only
-if ARCH_SA1100
+menuconfig ARCH_SA1100
+	bool "SA11x0 Implementations"
+	depends on ARCH_MULTI_V4 && !(ARCH_MULTI_V4T || ARCH_MULTI_V5)
+	depends on !(ARCH_MOXART || ARCH_GEMINI)
+	depends on ATAGS
+	depends on CPU_LITTLE_ENDIAN
+	depends on MMU
+	select ARCH_NO_SG_CHAIN
+	select ARCH_MTD_XIP
+	select CLKSRC_MMIO
+	select CLKSRC_PXA
+	select CPU_FREQ
+	select CPU_SA1100
+	select GPIOLIB
+	select IRQ_DOMAIN
+	select ISA
+	select NEED_MACH_MEMORY_H
+	help
+	  Support for StrongARM 11x0 based boards.
 
-menu "SA11x0 Implementations"
+if ARCH_SA1100
 
 config SA1100_ASSABET
 	bool "Assabet"
@@ -25,6 +43,7 @@ config ASSABET_NEPONSET
 
 config SA1100_CERF
 	bool "CerfBoard"
+	depends on UNUSED_BOARD_FILES
 	select ARM_SA1110_CPUFREQ
 	select LEDS_GPIO_REGISTER
 	help
@@ -62,6 +81,7 @@ config SA1100_COLLIE
 
 config SA1100_H3100
 	bool "Compaq iPAQ H3100"
+	depends on UNUSED_BOARD_FILES
 	select ARM_SA1110_CPUFREQ
 	select HTC_EGPIO
 	select MFD_IPAQ_MICRO
@@ -80,6 +100,7 @@ config SA1100_H3600
 
 config SA1100_BADGE4
 	bool "HP Labs BadgePAD 4"
+	depends on UNUSED_BOARD_FILES
 	select ARM_SA1100_CPUFREQ
 	select SA1111
 	help
@@ -88,6 +109,7 @@ config SA1100_BADGE4
 
 config SA1100_JORNADA720
 	bool "HP Jornada 720"
+	depends on UNUSED_BOARD_FILES
 	# FIXME: select ARM_SA11x0_CPUFREQ
 	select SA1111
 	help
@@ -107,6 +129,7 @@ config SA1100_JORNADA720_SSP
 
 config SA1100_HACKKIT
 	bool "HackKit Core CPU Board"
+	depends on UNUSED_BOARD_FILES
 	select ARM_SA1100_CPUFREQ
 	help
 	  Say Y here to support the HackKit Core CPU Board
@@ -114,6 +137,7 @@ config SA1100_HACKKIT
 
 config SA1100_LART
 	bool "LART"
+	depends on UNUSED_BOARD_FILES
 	select ARM_SA1100_CPUFREQ
 	help
 	  Say Y here if you are using the Linux Advanced Radio Terminal
@@ -122,6 +146,7 @@ config SA1100_LART
 
 config SA1100_NANOENGINE
 	bool "nanoEngine"
+	depends on UNUSED_BOARD_FILES
 	select ARM_SA1110_CPUFREQ
 	select FORCE_PCI
 	select PCI_NANOENGINE
@@ -132,6 +157,7 @@ config SA1100_NANOENGINE
 
 config SA1100_PLEB
 	bool "PLEB"
+	depends on UNUSED_BOARD_FILES
 	select ARM_SA1100_CPUFREQ
 	help
 	  Say Y here if you are using version 1 of the Portable Linux
@@ -141,6 +167,7 @@ config SA1100_PLEB
 
 config SA1100_SHANNON
 	bool "Shannon"
+	depends on UNUSED_BOARD_FILES
 	select ARM_SA1100_CPUFREQ
 	select REGULATOR
 	select REGULATOR_FIXED_VOLTAGE
@@ -152,6 +179,7 @@ config SA1100_SHANNON
 
 config SA1100_SIMPAD
 	bool "Simpad"
+	depends on UNUSED_BOARD_FILES
 	select ARM_SA1110_CPUFREQ
 	help
 	  The SIEMENS webpad SIMpad is based on the StrongARM 1110. There
@@ -163,12 +191,10 @@ config SA1100_SIMPAD
 
 config SA1100_SSP
 	tristate "Generic PIO SSP"
+	depends on UNUSED_BOARD_FILES
 	help
 	  Say Y here to enable support for the generic PIO SSP driver.
 	  This isn't for audio support, but for attached sensors and
 	  other devices, eg for BadgePAD 4 sensor support.
 
-endmenu
-
 endif
-
diff --git a/arch/arm/mach-sa1100/Makefile.boot b/arch/arm/mach-sa1100/Makefile.boot
deleted file mode 100644
index 9d8246f2cab4..000000000000
--- a/arch/arm/mach-sa1100/Makefile.boot
+++ /dev/null
@@ -1,9 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0-only
-ifeq ($(CONFIG_SA1111),y)
-   zreladdr-y	+= 0xc0208000
-else
-   zreladdr-y	+= 0xc0008000
-endif
-params_phys-y	:= 0xc0000100
-initrd_phys-y	:= 0xc0800000
-
diff --git a/arch/arm/mach-sa1100/generic.c b/arch/arm/mach-sa1100/generic.c
index 4dfb7554649d..6c21f214cd60 100644
--- a/arch/arm/mach-sa1100/generic.c
+++ b/arch/arm/mach-sa1100/generic.c
@@ -39,9 +39,6 @@
 #include "generic.h"
 #include <clocksource/pxa.h>
 
-unsigned int reset_status;
-EXPORT_SYMBOL(reset_status);
-
 #define NR_FREQS	16
 
 /*
@@ -319,10 +316,13 @@ static struct platform_device *sa11x0_devices[] __initdata = {
 
 static int __init sa1100_init(void)
 {
+	struct resource wdt_res = DEFINE_RES_MEM(0x90000000, 0x20);
 	pm_power_off = sa1100_power_off;
 
 	regulator_has_full_constraints();
 
+	platform_device_register_simple("sa1100_wdt", -1, &wdt_res, 1);
+
 	return platform_add_devices(sa11x0_devices, ARRAY_SIZE(sa11x0_devices));
 }
 
diff --git a/arch/arm/mach-sa1100/include/mach/reset.h b/arch/arm/mach-sa1100/include/mach/reset.h
index 27695650a567..a6723d45ae2a 100644
--- a/arch/arm/mach-sa1100/include/mach/reset.h
+++ b/arch/arm/mach-sa1100/include/mach/reset.h
@@ -10,7 +10,6 @@
 #define RESET_STATUS_GPIO	(1 << 3)	/* GPIO Reset */
 #define RESET_STATUS_ALL	(0xf)
 
-extern unsigned int reset_status;
 static inline void clear_reset_status(unsigned int mask)
 {
 	RCSR = mask;
diff --git a/arch/arm/mach-shmobile/Kconfig b/arch/arm/mach-shmobile/Kconfig
index 3683d6f10973..37f862f13c8d 100644
--- a/arch/arm/mach-shmobile/Kconfig
+++ b/arch/arm/mach-shmobile/Kconfig
@@ -1,10 +1,9 @@
 # SPDX-License-Identifier: GPL-2.0
 menuconfig ARCH_RENESAS
 	bool "Renesas ARM SoCs"
-	depends on ARCH_MULTI_V7 && MMU
+	depends on ARCH_MULTI_V7
 	select ARM_GIC
 	select GPIOLIB
 	select NO_IOPORT_MAP
 	select PINCTRL
-	select SOC_BUS
 	select ZONE_DMA if ARM_LPAE
diff --git a/arch/arm/mach-shmobile/regulator-quirk-rcar-gen2.c b/arch/arm/mach-shmobile/regulator-quirk-rcar-gen2.c
index ee949255ced3..117e7b07995b 100644
--- a/arch/arm/mach-shmobile/regulator-quirk-rcar-gen2.c
+++ b/arch/arm/mach-shmobile/regulator-quirk-rcar-gen2.c
@@ -67,7 +67,7 @@ static const struct of_device_id rcar_gen2_quirk_match[] = {
 	{ .compatible = "dlg,da9063", .data = &da9063_msg },
 	{ .compatible = "dlg,da9063l", .data = &da9063_msg },
 	{ .compatible = "dlg,da9210", .data = &da9210_msg },
-	{},
+	{ /* sentinel */ }
 };
 
 static int regulator_quirk_notify(struct notifier_block *nb,
@@ -125,6 +125,7 @@ remove:
 
 	list_for_each_entry_safe(pos, tmp, &quirk_list, list) {
 		list_del(&pos->list);
+		of_node_put(pos->np);
 		kfree(pos);
 	}
 
@@ -154,8 +155,10 @@ static int __init rcar_gen2_regulator_quirk(void)
 		return -ENODEV;
 
 	for_each_matching_node_and_match(np, rcar_gen2_quirk_match, &id) {
-		if (!of_device_is_available(np))
+		if (!of_device_is_available(np)) {
+			of_node_put(np);
 			break;
+		}
 
 		ret = of_property_read_u32(np, "reg", &addr);
 		if (ret)	/* Skip invalid entry and continue */
@@ -164,6 +167,7 @@ static int __init rcar_gen2_regulator_quirk(void)
 		quirk = kzalloc(sizeof(*quirk), GFP_KERNEL);
 		if (!quirk) {
 			ret = -ENOMEM;
+			of_node_put(np);
 			goto err_mem;
 		}
 
@@ -171,11 +175,12 @@ static int __init rcar_gen2_regulator_quirk(void)
 		memcpy(&quirk->i2c_msg, id->data, sizeof(quirk->i2c_msg));
 
 		quirk->id = id;
-		quirk->np = np;
+		quirk->np = of_node_get(np);
 		quirk->i2c_msg.addr = addr;
 
 		ret = of_irq_parse_one(np, 0, argsa);
 		if (ret) {	/* Skip invalid entry and continue */
+			of_node_put(np);
 			kfree(quirk);
 			continue;
 		}
@@ -222,6 +227,7 @@ err_free:
 err_mem:
 	list_for_each_entry_safe(pos, tmp, &quirk_list, list) {
 		list_del(&pos->list);
+		of_node_put(pos->np);
 		kfree(pos);
 	}
 
diff --git a/arch/arm/mach-shmobile/setup-emev2.c b/arch/arm/mach-shmobile/setup-emev2.c
index a328d2f52678..ed82d6429623 100644
--- a/arch/arm/mach-shmobile/setup-emev2.c
+++ b/arch/arm/mach-shmobile/setup-emev2.c
@@ -16,7 +16,7 @@
 
 static const char *const emev2_boards_compat_dt[] __initconst = {
 	"renesas,emev2",
-	NULL,
+	NULL
 };
 
 DT_MACHINE_START(EMEV2_DT, "Generic Emma Mobile EV2 (Flattened Device Tree)")
diff --git a/arch/arm/mach-shmobile/setup-r7s72100.c b/arch/arm/mach-shmobile/setup-r7s72100.c
index 14867226f8f4..a70b99495e2e 100644
--- a/arch/arm/mach-shmobile/setup-r7s72100.c
+++ b/arch/arm/mach-shmobile/setup-r7s72100.c
@@ -14,7 +14,7 @@
 
 static const char *const r7s72100_boards_compat_dt[] __initconst = {
 	"renesas,r7s72100",
-	NULL,
+	NULL
 };
 
 DT_MACHINE_START(R7S72100_DT, "Generic R7S72100 (Flattened Device Tree)")
diff --git a/arch/arm/mach-shmobile/setup-r7s9210.c b/arch/arm/mach-shmobile/setup-r7s9210.c
index 573fb9955e7e..90add728bc3d 100644
--- a/arch/arm/mach-shmobile/setup-r7s9210.c
+++ b/arch/arm/mach-shmobile/setup-r7s9210.c
@@ -15,7 +15,7 @@
 
 static const char *const r7s9210_boards_compat_dt[] __initconst = {
 	"renesas,r7s9210",
-	NULL,
+	NULL
 };
 
 DT_MACHINE_START(R7S72100_DT, "Generic R7S9210 (Flattened Device Tree)")
diff --git a/arch/arm/mach-shmobile/setup-r8a73a4.c b/arch/arm/mach-shmobile/setup-r8a73a4.c
index 23a29a0ea9c9..9e3f4dc08372 100644
--- a/arch/arm/mach-shmobile/setup-r8a73a4.c
+++ b/arch/arm/mach-shmobile/setup-r8a73a4.c
@@ -14,7 +14,7 @@
 
 static const char *const r8a73a4_boards_compat_dt[] __initconst = {
 	"renesas,r8a73a4",
-	NULL,
+	NULL
 };
 
 DT_MACHINE_START(R8A73A4_DT, "Generic R8A73A4 (Flattened Device Tree)")
diff --git a/arch/arm/mach-shmobile/setup-r8a7740.c b/arch/arm/mach-shmobile/setup-r8a7740.c
index f760c27c9907..9ac2b8a2aa6a 100644
--- a/arch/arm/mach-shmobile/setup-r8a7740.c
+++ b/arch/arm/mach-shmobile/setup-r8a7740.c
@@ -72,7 +72,7 @@ static void __init r8a7740_generic_init(void)
 
 static const char *const r8a7740_boards_compat_dt[] __initconst = {
 	"renesas,r8a7740",
-	NULL,
+	NULL
 };
 
 DT_MACHINE_START(R8A7740_DT, "Generic R8A7740 (Flattened Device Tree)")
diff --git a/arch/arm/mach-shmobile/setup-r8a7778.c b/arch/arm/mach-shmobile/setup-r8a7778.c
index 02cda9cada4c..445017e8cfe8 100644
--- a/arch/arm/mach-shmobile/setup-r8a7778.c
+++ b/arch/arm/mach-shmobile/setup-r8a7778.c
@@ -43,7 +43,7 @@ static void __init r8a7778_init_irq_dt(void)
 
 static const char *const r8a7778_compat_dt[] __initconst = {
 	"renesas,r8a7778",
-	NULL,
+	NULL
 };
 
 DT_MACHINE_START(R8A7778_DT, "Generic R8A7778 (Flattened Device Tree)")
diff --git a/arch/arm/mach-shmobile/setup-r8a7779.c b/arch/arm/mach-shmobile/setup-r8a7779.c
index b6e282116d66..c3af2c8925ba 100644
--- a/arch/arm/mach-shmobile/setup-r8a7779.c
+++ b/arch/arm/mach-shmobile/setup-r8a7779.c
@@ -49,7 +49,7 @@ static void __init r8a7779_init_irq_dt(void)
 
 static const char *const r8a7779_compat_dt[] __initconst = {
 	"renesas,r8a7779",
-	NULL,
+	NULL
 };
 
 DT_MACHINE_START(R8A7779_DT, "Generic R8A7779 (Flattened Device Tree)")
diff --git a/arch/arm/mach-shmobile/setup-rcar-gen2.c b/arch/arm/mach-shmobile/setup-rcar-gen2.c
index d42d93443f2f..3edbf0719fb3 100644
--- a/arch/arm/mach-shmobile/setup-rcar-gen2.c
+++ b/arch/arm/mach-shmobile/setup-rcar-gen2.c
@@ -199,7 +199,7 @@ static const char * const rcar_gen2_boards_compat_dt[] __initconst = {
 	"renesas,r8a7792",
 	"renesas,r8a7793",
 	"renesas,r8a7794",
-	NULL,
+	NULL
 };
 
 DT_MACHINE_START(RCAR_GEN2_DT, "Generic R-Car Gen2 (Flattened Device Tree)")
@@ -215,7 +215,7 @@ static const char * const rz_g1_boards_compat_dt[] __initconst = {
 	"renesas,r8a7744",
 	"renesas,r8a7745",
 	"renesas,r8a77470",
-	NULL,
+	NULL
 };
 
 DT_MACHINE_START(RZ_G1_DT, "Generic RZ/G1 (Flattened Device Tree)")
diff --git a/arch/arm/mach-shmobile/setup-sh73a0.c b/arch/arm/mach-shmobile/setup-sh73a0.c
index 890bf537b7de..7fb27240e907 100644
--- a/arch/arm/mach-shmobile/setup-sh73a0.c
+++ b/arch/arm/mach-shmobile/setup-sh73a0.c
@@ -32,7 +32,7 @@ static void __init sh73a0_generic_init(void)
 
 static const char *const sh73a0_boards_compat_dt[] __initconst = {
 	"renesas,sh73a0",
-	NULL,
+	NULL
 };
 
 DT_MACHINE_START(SH73A0_DT, "Generic SH73A0 (Flattened Device Tree)")
diff --git a/arch/arm/mach-socfpga/Kconfig b/arch/arm/mach-socfpga/Kconfig
index 43ddec677c0b..eb72c240c248 100644
--- a/arch/arm/mach-socfpga/Kconfig
+++ b/arch/arm/mach-socfpga/Kconfig
@@ -2,7 +2,7 @@
 menuconfig ARCH_INTEL_SOCFPGA
 	bool "Altera SOCFPGA family"
 	depends on ARCH_MULTI_V7
-	select ARCH_SUPPORTS_BIG_ENDIAN
+	select ARCH_HAS_RESET_CONTROLLER
 	select ARM_AMBA
 	select ARM_GIC
 	select CACHE_L2X0
@@ -18,6 +18,7 @@ menuconfig ARCH_INTEL_SOCFPGA
 	select PL310_ERRATA_727915
 	select PL310_ERRATA_753970 if PL310
 	select PL310_ERRATA_769419
+	select RESET_CONTROLLER
 
 if ARCH_INTEL_SOCFPGA
 config SOCFPGA_SUSPEND
diff --git a/arch/arm/mach-spear/Kconfig b/arch/arm/mach-spear/Kconfig
index 20e284563a80..1add7ee49b63 100644
--- a/arch/arm/mach-spear/Kconfig
+++ b/arch/arm/mach-spear/Kconfig
@@ -5,7 +5,7 @@
 
 menuconfig PLAT_SPEAR
 	bool "ST SPEAr Family"
-	depends on ARCH_MULTI_V7 || ARCH_MULTI_V5
+	depends on ARCH_MULTI_V7 || (ARCH_MULTI_V5 && CPU_LITTLE_ENDIAN)
 	select ARM_AMBA
 	select CLKSRC_MMIO
 	select GPIOLIB
diff --git a/arch/arm/mach-spear/Makefile b/arch/arm/mach-spear/Makefile
index 176b14f83089..c6101a843601 100644
--- a/arch/arm/mach-spear/Makefile
+++ b/arch/arm/mach-spear/Makefile
@@ -3,8 +3,6 @@
 # SPEAr Platform specific Makefile
 #
 
-ccflags-$(CONFIG_ARCH_MULTIPLATFORM) := -I$(srctree)/$(src)/include
-
 # Common support
 obj-y	:= restart.o time.o
 
diff --git a/arch/arm/mach-spear/generic.h b/arch/arm/mach-spear/generic.h
index 8ec2b92dca19..9e36920d4cfd 100644
--- a/arch/arm/mach-spear/generic.h
+++ b/arch/arm/mach-spear/generic.h
@@ -1,13 +1,10 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * spear machine family generic header file
  *
  * Copyright (C) 2009-2012 ST Microelectronics
  * Rajeev Kumar <rajeev-dlh.kumar@st.com>
  * Viresh Kumar <vireshk@kernel.org>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #ifndef __MACH_GENERIC_H
@@ -28,11 +25,8 @@ extern struct pl022_ssp_controller pl022_plat_data;
 extern struct pl08x_platform_data pl080_plat_data;
 
 void __init spear_setup_of_timer(void);
-void __init spear3xx_clk_init(void __iomem *misc_base,
-			      void __iomem *soc_config_base);
 void __init spear3xx_map_io(void);
 void __init spear3xx_dt_init_irq(void);
-void __init spear6xx_clk_init(void __iomem *misc_base);
 void __init spear13xx_map_io(void);
 void __init spear13xx_l2x0_init(void);
 
diff --git a/arch/arm/mach-spear/include/mach/irqs.h b/arch/arm/mach-spear/include/mach/irqs.h
deleted file mode 100644
index 7058720c5278..000000000000
--- a/arch/arm/mach-spear/include/mach/irqs.h
+++ /dev/null
@@ -1,35 +0,0 @@
-/*
- * IRQ helper macros for spear machine family
- *
- * Copyright (C) 2009-2012 ST Microelectronics
- * Rajeev Kumar <rajeev-dlh.kumar@st.com>
- * Viresh Kumar <vireshk@kernel.org>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#ifndef __MACH_IRQS_H
-#define __MACH_IRQS_H
-
-#ifdef CONFIG_ARCH_SPEAR3XX
-#define NR_IRQS			256
-#endif
-
-#ifdef CONFIG_ARCH_SPEAR6XX
-/* IRQ definitions */
-/* VIC 1 */
-#define IRQ_VIC_END				64
-
-/* GPIO pins virtual irqs */
-#define VIRTUAL_IRQS				24
-#define NR_IRQS					(IRQ_VIC_END + VIRTUAL_IRQS)
-#endif
-
-#ifdef CONFIG_ARCH_SPEAR13XX
-#define IRQ_GIC_END			160
-#define NR_IRQS				IRQ_GIC_END
-#endif
-
-#endif /* __MACH_IRQS_H */
diff --git a/arch/arm/mach-spear/include/mach/misc_regs.h b/arch/arm/mach-spear/include/mach/misc_regs.h
deleted file mode 100644
index cfaf7c665b58..000000000000
--- a/arch/arm/mach-spear/include/mach/misc_regs.h
+++ /dev/null
@@ -1,22 +0,0 @@
-/*
- * arch/arm/mach-spear3xx/include/mach/misc_regs.h
- *
- * Miscellaneous registers definitions for SPEAr3xx machine family
- *
- * Copyright (C) 2009 ST Microelectronics
- * Viresh Kumar <vireshk@kernel.org>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#ifndef __MACH_MISC_REGS_H
-#define __MACH_MISC_REGS_H
-
-#include <mach/spear.h>
-
-#define MISC_BASE		(VA_SPEAR_ICM3_MISC_REG_BASE)
-#define DMA_CHN_CFG		(MISC_BASE + 0x0A0)
-
-#endif /* __MACH_MISC_REGS_H */
diff --git a/arch/arm/mach-spear/include/mach/uncompress.h b/arch/arm/mach-spear/include/mach/uncompress.h
deleted file mode 100644
index 8439b9c12edb..000000000000
--- a/arch/arm/mach-spear/include/mach/uncompress.h
+++ /dev/null
@@ -1,42 +0,0 @@
-/*
- * arch/arm/plat-spear/include/plat/uncompress.h
- *
- * Serial port stubs for kernel decompress status messages
- *
- * Copyright (C) 2009 ST Microelectronics
- * Viresh Kumar <vireshk@kernel.org>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-
-#include <linux/io.h>
-#include <linux/amba/serial.h>
-#include <mach/spear.h>
-
-#ifndef __PLAT_UNCOMPRESS_H
-#define __PLAT_UNCOMPRESS_H
-/*
- * This does not append a newline
- */
-static inline void putc(int c)
-{
-	void __iomem *base = (void __iomem *)SPEAR_DBG_UART_BASE;
-
-	while (readl_relaxed(base + UART01x_FR) & UART01x_FR_TXFF)
-		barrier();
-
-	writel_relaxed(c, base + UART01x_DR);
-}
-
-static inline void flush(void)
-{
-}
-
-/*
- * nothing to do
- */
-#define arch_decomp_setup()
-
-#endif /* __PLAT_UNCOMPRESS_H */
diff --git a/arch/arm/mach-spear/misc_regs.h b/arch/arm/mach-spear/misc_regs.h
new file mode 100644
index 000000000000..72aa801a3a89
--- /dev/null
+++ b/arch/arm/mach-spear/misc_regs.h
@@ -0,0 +1,17 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Miscellaneous registers definitions for SPEAr3xx machine family
+ *
+ * Copyright (C) 2009 ST Microelectronics
+ * Viresh Kumar <vireshk@kernel.org>
+ */
+
+#ifndef __MACH_MISC_REGS_H
+#define __MACH_MISC_REGS_H
+
+#include "spear.h"
+
+#define MISC_BASE		(VA_SPEAR_ICM3_MISC_REG_BASE)
+#define DMA_CHN_CFG		(MISC_BASE + 0x0A0)
+
+#endif /* __MACH_MISC_REGS_H */
diff --git a/arch/arm/mach-spear/pl080.c b/arch/arm/mach-spear/pl080.c
index b4529f3e0ee9..d6b8627d2544 100644
--- a/arch/arm/mach-spear/pl080.c
+++ b/arch/arm/mach-spear/pl080.c
@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/plat-spear/pl080.c
  *
@@ -5,10 +6,6 @@
  *
  * Copyright (C) 2012 ST Microelectronics
  * Viresh Kumar <vireshk@kernel.org>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #include <linux/amba/pl08x.h>
@@ -17,8 +14,8 @@
 #include <linux/err.h>
 #include <linux/io.h>
 #include <linux/spinlock_types.h>
-#include <mach/spear.h>
-#include <mach/misc_regs.h>
+#include "spear.h"
+#include "misc_regs.h"
 
 static spinlock_t lock = __SPIN_LOCK_UNLOCKED(x);
 
diff --git a/arch/arm/mach-spear/pl080.h b/arch/arm/mach-spear/pl080.h
index 608dec6725ae..3732d940dbfb 100644
--- a/arch/arm/mach-spear/pl080.h
+++ b/arch/arm/mach-spear/pl080.h
@@ -1,3 +1,4 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * arch/arm/plat-spear/include/plat/pl080.h
  *
@@ -5,10 +6,6 @@
  *
  * Copyright (C) 2012 ST Microelectronics
  * Viresh Kumar <vireshk@kernel.org>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #ifndef __PLAT_PL080_H
diff --git a/arch/arm/mach-spear/platsmp.c b/arch/arm/mach-spear/platsmp.c
index e33a85c28c95..97fbda998df9 100644
--- a/arch/arm/mach-spear/platsmp.c
+++ b/arch/arm/mach-spear/platsmp.c
@@ -14,7 +14,7 @@
 #include <linux/smp.h>
 #include <asm/cacheflush.h>
 #include <asm/smp_scu.h>
-#include <mach/spear.h>
+#include "spear.h"
 #include "generic.h"
 
 /* XXX spear_pen_release is cargo culted code - DO NOT COPY XXX */
diff --git a/arch/arm/mach-spear/restart.c b/arch/arm/mach-spear/restart.c
index b4342155a783..76fb16cc8132 100644
--- a/arch/arm/mach-spear/restart.c
+++ b/arch/arm/mach-spear/restart.c
@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/plat-spear/restart.c
  *
@@ -5,16 +6,12 @@
  *
  * Copyright (C) 2009 ST Microelectronics
  * Viresh Kumar <vireshk@kernel.org>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 #include <linux/io.h>
 #include <linux/amba/sp810.h>
 #include <linux/reboot.h>
 #include <asm/system_misc.h>
-#include <mach/spear.h>
+#include "spear.h"
 #include "generic.h"
 
 #define SPEAR13XX_SYS_SW_RES			(VA_MISC_BASE + 0x204)
diff --git a/arch/arm/mach-spear/include/mach/spear.h b/arch/arm/mach-spear/spear.h
index 5ed841ccf8a3..432efd407c76 100644
--- a/arch/arm/mach-spear/include/mach/spear.h
+++ b/arch/arm/mach-spear/spear.h
@@ -1,13 +1,10 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * SPEAr3xx/6xx Machine family specific definition
  *
  * Copyright (C) 2009,2012 ST Microelectronics
  * Rajeev Kumar<rajeev-dlh.kumar@st.com>
  * Viresh Kumar <vireshk@kernel.org>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #ifndef __MACH_SPEAR_H
diff --git a/arch/arm/mach-spear/spear1310.c b/arch/arm/mach-spear/spear1310.c
index a7d4f136836f..89d388388e02 100644
--- a/arch/arm/mach-spear/spear1310.c
+++ b/arch/arm/mach-spear/spear1310.c
@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/mach-spear13xx/spear1310.c
  *
@@ -5,10 +6,6 @@
  *
  * Copyright (C) 2012 ST Microelectronics
  * Viresh Kumar <vireshk@kernel.org>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #define pr_fmt(fmt) "SPEAr1310: " fmt
@@ -18,7 +15,7 @@
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
 #include "generic.h"
-#include <mach/spear.h>
+#include "spear.h"
 
 /* Base addresses */
 #define SPEAR1310_RAS_GRP1_BASE			UL(0xD8000000)
diff --git a/arch/arm/mach-spear/spear1340.c b/arch/arm/mach-spear/spear1340.c
index a212af90c0bc..a391f154eff9 100644
--- a/arch/arm/mach-spear/spear1340.c
+++ b/arch/arm/mach-spear/spear1340.c
@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/mach-spear13xx/spear1340.c
  *
@@ -5,10 +6,6 @@
  *
  * Copyright (C) 2012 ST Microelectronics
  * Viresh Kumar <vireshk@kernel.org>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #define pr_fmt(fmt) "SPEAr1340: " fmt
diff --git a/arch/arm/mach-spear/spear13xx.c b/arch/arm/mach-spear/spear13xx.c
index 74d1ca2a529a..ac5b76bbeab5 100644
--- a/arch/arm/mach-spear/spear13xx.c
+++ b/arch/arm/mach-spear/spear13xx.c
@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/mach-spear13xx/spear13xx.c
  *
@@ -5,10 +6,6 @@
  *
  * Copyright (C) 2012 ST Microelectronics
  * Viresh Kumar <vireshk@kernel.org>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #define pr_fmt(fmt) "SPEAr13xx: " fmt
@@ -21,7 +18,7 @@
 #include <linux/of.h>
 #include <asm/hardware/cache-l2x0.h>
 #include <asm/mach/map.h>
-#include <mach/spear.h>
+#include "spear.h"
 #include "generic.h"
 
 void __init spear13xx_l2x0_init(void)
@@ -29,7 +26,7 @@ void __init spear13xx_l2x0_init(void)
 	/*
 	 * 512KB (64KB/way), 8-way associativity, parity supported
 	 *
-	 * FIXME: 9th bit, of Auxillary Controller register must be set
+	 * FIXME: 9th bit, of Auxiliary Controller register must be set
 	 * for some spear13xx devices for stable L2 operation.
 	 *
 	 * Enable Early BRESP, L2 prefetch for Instruction and Data,
diff --git a/arch/arm/mach-spear/spear300.c b/arch/arm/mach-spear/spear300.c
index 325b89579be1..1d6b6e10fcf6 100644
--- a/arch/arm/mach-spear/spear300.c
+++ b/arch/arm/mach-spear/spear300.c
@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/mach-spear3xx/spear300.c
  *
@@ -5,10 +6,6 @@
  *
  * Copyright (C) 2009-2012 ST Microelectronics
  * Viresh Kumar <vireshk@kernel.org>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #define pr_fmt(fmt) "SPEAr300: " fmt
@@ -17,7 +14,7 @@
 #include <linux/of_platform.h>
 #include <asm/mach/arch.h>
 #include "generic.h"
-#include <mach/spear.h>
+#include "spear.h"
 
 /* DMAC platform data's slave info */
 struct pl08x_channel_data spear300_dma_info[] = {
diff --git a/arch/arm/mach-spear/spear310.c b/arch/arm/mach-spear/spear310.c
index 59e173dc85cf..da4643b9f3bb 100644
--- a/arch/arm/mach-spear/spear310.c
+++ b/arch/arm/mach-spear/spear310.c
@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/mach-spear3xx/spear310.c
  *
@@ -5,10 +6,6 @@
  *
  * Copyright (C) 2009-2012 ST Microelectronics
  * Viresh Kumar <vireshk@kernel.org>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #define pr_fmt(fmt) "SPEAr310: " fmt
@@ -18,7 +15,7 @@
 #include <linux/of_platform.h>
 #include <asm/mach/arch.h>
 #include "generic.h"
-#include <mach/spear.h>
+#include "spear.h"
 
 #define SPEAR310_UART1_BASE		UL(0xB2000000)
 #define SPEAR310_UART2_BASE		UL(0xB2080000)
diff --git a/arch/arm/mach-spear/spear320.c b/arch/arm/mach-spear/spear320.c
index 926d5a243238..12aa82b987ac 100644
--- a/arch/arm/mach-spear/spear320.c
+++ b/arch/arm/mach-spear/spear320.c
@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/mach-spear3xx/spear320.c
  *
@@ -5,10 +6,6 @@
  *
  * Copyright (C) 2009-2012 ST Microelectronics
  * Viresh Kumar <vireshk@kernel.org>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #define pr_fmt(fmt) "SPEAr320: " fmt
@@ -20,7 +17,7 @@
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
 #include "generic.h"
-#include <mach/spear.h>
+#include "spear.h"
 
 #define SPEAR320_UART1_BASE		UL(0xA3000000)
 #define SPEAR320_UART2_BASE		UL(0xA4000000)
diff --git a/arch/arm/mach-spear/spear3xx.c b/arch/arm/mach-spear/spear3xx.c
index f83321d5e353..7ef9670d3029 100644
--- a/arch/arm/mach-spear/spear3xx.c
+++ b/arch/arm/mach-spear/spear3xx.c
@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/mach-spear3xx/spear3xx.c
  *
@@ -5,10 +6,6 @@
  *
  * Copyright (C) 2009-2012 ST Microelectronics
  * Viresh Kumar <vireshk@kernel.org>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #define pr_fmt(fmt) "SPEAr3xx: " fmt
@@ -16,12 +13,13 @@
 #include <linux/amba/pl022.h>
 #include <linux/amba/pl080.h>
 #include <linux/clk.h>
+#include <linux/clk/spear.h>
 #include <linux/io.h>
 #include <asm/mach/map.h>
 #include "pl080.h"
 #include "generic.h"
-#include <mach/spear.h>
-#include <mach/misc_regs.h>
+#include "spear.h"
+#include "misc_regs.h"
 
 /* ssp device registration */
 struct pl022_ssp_controller pl022_plat_data = {
diff --git a/arch/arm/mach-spear/spear6xx.c b/arch/arm/mach-spear/spear6xx.c
index c5fc110134ba..f0a1e704cceb 100644
--- a/arch/arm/mach-spear/spear6xx.c
+++ b/arch/arm/mach-spear/spear6xx.c
@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/mach-spear6xx/spear6xx.c
  *
@@ -7,14 +8,11 @@
  * Rajeev Kumar<rajeev-dlh.kumar@st.com>
  *
  * Copyright 2012 Stefan Roese <sr@denx.de>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #include <linux/amba/pl08x.h>
 #include <linux/clk.h>
+#include <linux/clk/spear.h>
 #include <linux/err.h>
 #include <linux/of.h>
 #include <linux/of_address.h>
@@ -25,8 +23,8 @@
 #include <asm/mach/map.h>
 #include "pl080.h"
 #include "generic.h"
-#include <mach/spear.h>
-#include <mach/misc_regs.h>
+#include "spear.h"
+#include "misc_regs.h"
 
 /* dmac device registration */
 static struct pl08x_channel_data spear600_dma_info[] = {
@@ -342,7 +340,7 @@ static struct pl08x_platform_data spear6xx_pl080_plat_data = {
  * 0xD0000000		0xFD000000
  * 0xFC000000		0xFC000000
  */
-struct map_desc spear6xx_io_desc[] __initdata = {
+static struct map_desc spear6xx_io_desc[] __initdata = {
 	{
 		.virtual	= (unsigned long)VA_SPEAR6XX_ML_CPU_BASE,
 		.pfn		= __phys_to_pfn(SPEAR_ICM3_ML1_2_BASE),
@@ -362,12 +360,12 @@ struct map_desc spear6xx_io_desc[] __initdata = {
 };
 
 /* This will create static memory mapping for selected devices */
-void __init spear6xx_map_io(void)
+static void __init spear6xx_map_io(void)
 {
 	iotable_init(spear6xx_io_desc, ARRAY_SIZE(spear6xx_io_desc));
 }
 
-void __init spear6xx_timer_init(void)
+static void __init spear6xx_timer_init(void)
 {
 	char pclk_name[] = "pll3_clk";
 	struct clk *gpt_clk, *pclk;
@@ -397,7 +395,7 @@ void __init spear6xx_timer_init(void)
 }
 
 /* Add auxdata to pass platform data */
-struct of_dev_auxdata spear6xx_auxdata_lookup[] __initdata = {
+static struct of_dev_auxdata spear6xx_auxdata_lookup[] __initdata = {
 	OF_DEV_AUXDATA("arm,pl080", SPEAR_ICM3_DMA_BASE, NULL,
 			&spear6xx_pl080_plat_data),
 	{}
diff --git a/arch/arm/mach-spear/time.c b/arch/arm/mach-spear/time.c
index d1fdb6066f7b..e979e2197f8e 100644
--- a/arch/arm/mach-spear/time.c
+++ b/arch/arm/mach-spear/time.c
@@ -1,12 +1,9 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/plat-spear/time.c
  *
  * Copyright (C) 2010 ST Microelectronics
  * Shiraz Hashim<shiraz.linux.kernel@gmail.com>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
  */
 
 #include <linux/clk.h>
@@ -218,13 +215,13 @@ void __init spear_setup_of_timer(void)
 	irq = irq_of_parse_and_map(np, 0);
 	if (!irq) {
 		pr_err("%s: No irq passed for timer via DT\n", __func__);
-		return;
+		goto err_put_np;
 	}
 
 	gpt_base = of_iomap(np, 0);
 	if (!gpt_base) {
 		pr_err("%s: of iomap failed\n", __func__);
-		return;
+		goto err_put_np;
 	}
 
 	gpt_clk = clk_get_sys("gpt0", NULL);
@@ -239,6 +236,8 @@ void __init spear_setup_of_timer(void)
 		goto err_prepare_enable_clk;
 	}
 
+	of_node_put(np);
+
 	spear_clockevent_init(irq);
 	spear_clocksource_init();
 
@@ -248,4 +247,6 @@ err_prepare_enable_clk:
 	clk_put(gpt_clk);
 err_iomap:
 	iounmap(gpt_base);
+err_put_np:
+	of_node_put(np);
 }
diff --git a/arch/arm/mach-stm32/Makefile.boot b/arch/arm/mach-stm32/Makefile.boot
deleted file mode 100644
index 5dde7328a7a9..000000000000
--- a/arch/arm/mach-stm32/Makefile.boot
+++ /dev/null
@@ -1,4 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0-only
-# Empty file waiting for deletion once Makefile.boot isn't needed any more.
-# Patch waits for application at
-# https://www.arm.linux.org.uk/developer/patches/viewpatch.php?id=7889/1 .
diff --git a/arch/arm/mach-sunplus/Kconfig b/arch/arm/mach-sunplus/Kconfig
new file mode 100644
index 000000000000..d0c2416e6f24
--- /dev/null
+++ b/arch/arm/mach-sunplus/Kconfig
@@ -0,0 +1,27 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+
+menuconfig ARCH_SUNPLUS
+	bool "Sunplus SoCs"
+	depends on ARCH_MULTI_V7
+	help
+	  Support for Sunplus SoC family: SP7021 and succeeding SoC-based systems,
+	  such as the Banana Pi BPI-F2S development board (and derivatives).
+	  (<http://www.sinovoip.com.cn/ecp_view.asp?id=586>)
+	  (<https://tibbo.com/store/plus1.html>)
+
+config SOC_SP7021
+	bool "Sunplus SP7021 SoC support"
+	depends on ARCH_SUNPLUS
+	default ARCH_SUNPLUS
+	select HAVE_ARM_ARCH_TIMER
+	select ARM_GIC
+	select ARM_PSCI
+	select PINCTRL
+	select PINCTRL_SPPCTL
+	select SERIAL_SUNPLUS if TTY
+	select SERIAL_SUNPLUS_CONSOLE if TTY
+	help
+	  Support for Sunplus SP7021 SoC. It is based on ARM 4-core
+	  Cortex-A7 with various peripherals (e.g.: I2C, SPI, SDIO,
+	  Ethernet, etc.), FPGA interface,  chip-to-chip bus.
+	  It is designed for industrial control.
diff --git a/arch/arm/mach-sunplus/Makefile b/arch/arm/mach-sunplus/Makefile
new file mode 100644
index 000000000000..d211de6af2db
--- /dev/null
+++ b/arch/arm/mach-sunplus/Makefile
@@ -0,0 +1,8 @@
+# SPDX-License-Identifier: GPL-2.0
+#
+# Makefile for the linux kernel.
+#
+
+# Object file lists.
+
+obj-$(CONFIG_SOC_SP7021)	+= sp7021.o
diff --git a/arch/arm/mach-sunplus/sp7021.c b/arch/arm/mach-sunplus/sp7021.c
new file mode 100644
index 000000000000..774d0a5bd4eb
--- /dev/null
+++ b/arch/arm/mach-sunplus/sp7021.c
@@ -0,0 +1,16 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+/*
+ * Copyright (C) Sunplus Technology Co., Ltd.
+ *       All rights reserved.
+ */
+#include <linux/kernel.h>
+#include <asm/mach/arch.h>
+
+static const char *sp7021_compat[] __initconst = {
+	"sunplus,sp7021",
+	NULL
+};
+
+DT_MACHINE_START(SP7021_DT, "SP7021")
+	.dt_compat	= sp7021_compat,
+MACHINE_END
diff --git a/arch/arm/mach-sunxi/Kconfig b/arch/arm/mach-sunxi/Kconfig
index e5c2fce281cd..e015f2497111 100644
--- a/arch/arm/mach-sunxi/Kconfig
+++ b/arch/arm/mach-sunxi/Kconfig
@@ -1,13 +1,10 @@
 # SPDX-License-Identifier: GPL-2.0-only
 menuconfig ARCH_SUNXI
 	bool "Allwinner SoCs"
-	depends on ARCH_MULTI_V5 || ARCH_MULTI_V7
+	depends on (CPU_LITTLE_ENDIAN && ARCH_MULTI_V5) || ARCH_MULTI_V7
 	select ARCH_HAS_RESET_CONTROLLER
 	select CLKSRC_MMIO
-	select GENERIC_IRQ_CHIP
 	select GPIOLIB
-	select IRQ_DOMAIN_HIERARCHY
-	select IRQ_FASTEOI_HIERARCHY_HANDLERS
 	select PINCTRL
 	select PM_OPP
 	select SUN4I_TIMER
@@ -22,10 +19,12 @@ if ARCH_MULTI_V7
 config MACH_SUN4I
 	bool "Allwinner A10 (sun4i) SoCs support"
 	default ARCH_SUNXI
+	select SUN4I_INTC
 
 config MACH_SUN5I
 	bool "Allwinner A10s / A13 (sun5i) SoCs support"
 	default ARCH_SUNXI
+	select SUN4I_INTC
 	select SUN5I_HSTIMER
 
 config MACH_SUN6I
@@ -34,26 +33,31 @@ config MACH_SUN6I
 	select ARM_GIC
 	select MFD_SUN6I_PRCM
 	select SUN5I_HSTIMER
+	select SUN6I_R_INTC
+	select SUNXI_NMI_INTC
 
 config MACH_SUN7I
 	bool "Allwinner A20 (sun7i) SoCs support"
 	default ARCH_SUNXI
 	select ARM_GIC
 	select ARM_PSCI
-	select ARCH_SUPPORTS_BIG_ENDIAN
 	select HAVE_ARM_ARCH_TIMER
 	select SUN5I_HSTIMER
+	select SUNXI_NMI_INTC
 
 config MACH_SUN8I
 	bool "Allwinner sun8i Family SoCs support"
 	default ARCH_SUNXI
 	select ARM_GIC
 	select MFD_SUN6I_PRCM
+	select SUN6I_R_INTC
+	select SUNXI_NMI_INTC
 
 config MACH_SUN9I
 	bool "Allwinner (sun9i) SoCs support"
 	default ARCH_SUNXI
 	select ARM_GIC
+	select SUNXI_NMI_INTC
 
 config ARCH_SUNXI_MC_SMP
 	bool
@@ -69,6 +73,7 @@ if ARCH_MULTI_V5
 config MACH_SUNIV
 	bool "Allwinner ARMv5 F-series (suniv) SoCs support"
 	default ARCH_SUNXI
+	select SUN4I_INTC
 	help
 	  Support for Allwinner suniv ARMv5 SoCs.
 	  (F1C100A, F1C100s, F1C200s, F1C500, F1C600)
diff --git a/arch/arm/mach-tegra/platsmp.c b/arch/arm/mach-tegra/platsmp.c
index e6911a14c096..1f57e7c0feae 100644
--- a/arch/arm/mach-tegra/platsmp.c
+++ b/arch/arm/mach-tegra/platsmp.c
@@ -83,7 +83,7 @@ static int tegra30_boot_secondary(unsigned int cpu, struct task_struct *idle)
 	 * For warm boot CPU that was resumed from CPU hotplug, the
 	 * power will be resumed automatically after un-halting the
 	 * flow controller of the warm boot CPU. We need to wait for
-	 * the confirmaiton that the CPU is powered then removing
+	 * the confirmation that the CPU is powered then removing
 	 * the IO clamps.
 	 * For cold boot CPU, do not wait. After the cold boot CPU be
 	 * booted, it will run to tegra_secondary_init() and set
diff --git a/arch/arm/mach-ux500/Kconfig b/arch/arm/mach-ux500/Kconfig
index 24ed7f4a87a4..c18def269137 100644
--- a/arch/arm/mach-ux500/Kconfig
+++ b/arch/arm/mach-ux500/Kconfig
@@ -1,7 +1,7 @@
 # SPDX-License-Identifier: GPL-2.0
 menuconfig ARCH_U8500
 	bool "ST-Ericsson U8500 Series"
-	depends on ARCH_MULTI_V7 && MMU
+	depends on ARCH_MULTI_V7
 	select AB8500_CORE
 	select ABX500_CORE
 	select ARM_AMBA
diff --git a/arch/arm/mach-versatile/Kconfig b/arch/arm/mach-versatile/Kconfig
index f78a1d358031..b1519b4dc03a 100644
--- a/arch/arm/mach-versatile/Kconfig
+++ b/arch/arm/mach-versatile/Kconfig
@@ -2,6 +2,7 @@
 config ARCH_VERSATILE
 	bool "ARM Ltd. Versatile family"
 	depends on ARCH_MULTI_V5
+	depends on CPU_LITTLE_ENDIAN
 	select ARM_AMBA
 	select ARM_TIMER_SP804
 	select ARM_VIC
@@ -16,3 +17,310 @@ config ARCH_VERSATILE
 	help
 	  This enables support for ARM Ltd Versatile board.
 
+menuconfig ARCH_INTEGRATOR
+	bool "ARM Ltd. Integrator family"
+	depends on ARCH_MULTI_V4T || ARCH_MULTI_V5 || ARCH_MULTI_V6
+	depends on CPU_LITTLE_ENDIAN || ARCH_MULTI_V6
+	select ARM_AMBA
+	select CMA
+	select DMA_CMA
+	select HAVE_TCM
+	select CLK_ICST
+	select MFD_SYSCON
+	select PLAT_VERSATILE
+	select POWER_RESET
+	select POWER_RESET_VERSATILE
+	select POWER_SUPPLY
+	select SOC_INTEGRATOR_CM
+	select VERSATILE_FPGA_IRQ
+	help
+	  Support for ARM's Integrator platform.
+
+if ARCH_INTEGRATOR
+
+config ARCH_INTEGRATOR_AP
+	bool "Support Integrator/AP and Integrator/PP2 platforms"
+	select INTEGRATOR_AP_TIMER
+	select SERIAL_AMBA_PL010 if TTY
+	select SERIAL_AMBA_PL010_CONSOLE if TTY
+	select SOC_BUS
+	help
+	  Include support for the ARM(R) Integrator/AP and
+	  Integrator/PP2 platforms.
+
+config INTEGRATOR_IMPD1
+	bool "Include support for Integrator/IM-PD1"
+	depends on ARCH_INTEGRATOR_AP
+	select ARM_VIC
+	select GPIO_PL061
+	select GPIOLIB
+	select REGULATOR
+	select REGULATOR_FIXED_VOLTAGE
+	help
+	  The IM-PD1 is an add-on logic module for the Integrator which
+	  allows ARM(R) Ltd PrimeCells to be developed and evaluated.
+	  The IM-PD1 can be found on the Integrator/PP2 platform.
+
+config INTEGRATOR_CM720T
+	bool "Integrator/CM720T core module"
+	depends on ARCH_INTEGRATOR_AP
+	depends on ARCH_MULTI_V4T
+	select CPU_ARM720T
+
+config INTEGRATOR_CM920T
+	bool "Integrator/CM920T core module"
+	depends on ARCH_INTEGRATOR_AP
+	depends on ARCH_MULTI_V4T
+	select CPU_ARM920T
+
+config INTEGRATOR_CM922T_XA10
+	bool "Integrator/CM922T-XA10 core module"
+	depends on ARCH_MULTI_V4T
+	depends on ARCH_INTEGRATOR_AP
+	select CPU_ARM922T
+
+config INTEGRATOR_CM926EJS
+	bool "Integrator/CM926EJ-S core module"
+	depends on ARCH_INTEGRATOR_AP
+	depends on ARCH_MULTI_V5
+	select CPU_ARM926T
+
+config INTEGRATOR_CM10200E_REV0
+	bool "Integrator/CM10200E rev.0 core module"
+	depends on ARCH_INTEGRATOR_AP && n
+	depends on ARCH_MULTI_V5
+	select CPU_ARM1020
+
+config INTEGRATOR_CM10200E
+	bool "Integrator/CM10200E core module"
+	depends on ARCH_INTEGRATOR_AP && n
+	depends on ARCH_MULTI_V5
+	select CPU_ARM1020E
+
+config INTEGRATOR_CM10220E
+	bool "Integrator/CM10220E core module"
+	depends on ARCH_INTEGRATOR_AP
+	depends on ARCH_MULTI_V5
+	select CPU_ARM1022
+
+config INTEGRATOR_CM1026EJS
+	bool "Integrator/CM1026EJ-S core module"
+	depends on ARCH_INTEGRATOR_AP
+	depends on ARCH_MULTI_V5
+	select CPU_ARM1026
+
+config INTEGRATOR_CM1136JFS
+	bool "Integrator/CM1136JF-S core module"
+	depends on ARCH_INTEGRATOR_AP
+	depends on ARCH_MULTI_V6
+	select CPU_V6
+
+config ARCH_INTEGRATOR_CP
+	bool "Support Integrator/CP platform"
+	depends on ARCH_MULTI_V5 || ARCH_MULTI_V6
+	select ARM_TIMER_SP804
+	select SERIAL_AMBA_PL011 if TTY
+	select SERIAL_AMBA_PL011_CONSOLE if TTY
+	select SOC_BUS
+	help
+	  Include support for the ARM(R) Integrator CP platform.
+
+config INTEGRATOR_CT926
+	bool "Integrator/CT926 (ARM926EJ-S) core tile"
+	depends on ARCH_INTEGRATOR_CP
+	depends on ARCH_MULTI_V5
+	select CPU_ARM926T
+
+config INTEGRATOR_CTB36
+	bool "Integrator/CTB36 (ARM1136JF-S) core tile"
+	depends on ARCH_INTEGRATOR_CP
+	depends on ARCH_MULTI_V6
+	select CPU_V6
+
+config ARCH_CINTEGRATOR
+	depends on ARCH_INTEGRATOR_CP
+	def_bool y
+
+endif
+
+menuconfig ARCH_REALVIEW
+	bool "ARM Ltd. RealView family"
+	depends on (CPU_LITTLE_ENDIAN && ARCH_MULTI_V5) || ARCH_MULTI_V6 || ARCH_MULTI_V7
+	select ARM_AMBA
+	select ARM_GIC
+	select ARM_TIMER_SP804
+	select CLK_SP810
+	select GPIO_PL061 if GPIOLIB
+	select HAVE_ARM_SCU if SMP
+	select HAVE_ARM_TWD if SMP
+	select HAVE_PATA_PLATFORM
+	select HAVE_TCM
+	select CLK_ICST
+	select MACH_REALVIEW_EB if ARCH_MULTI_V5
+	select MFD_SYSCON
+	select PLAT_VERSATILE
+	select POWER_RESET
+	select POWER_RESET_VERSATILE
+	select POWER_SUPPLY
+	select SOC_REALVIEW
+	help
+	  This enables support for ARM Ltd RealView boards.
+
+if ARCH_REALVIEW
+
+config MACH_REALVIEW_EB
+	bool "Support RealView(R) Emulation Baseboard"
+	select ARM_GIC
+	select CPU_ARM926T if ARCH_MULTI_V5
+	help
+	  Include support for the ARM(R) RealView(R) Emulation Baseboard
+	  platform. On an ARMv5 kernel, this will include support for
+	  the ARM926EJ-S core tile, while on an ARMv6/v7 kernel, at least
+	  one of the ARM1136, ARM1176, ARM11MPCore or Cortex-A9MPCore
+	  core tile options should be enabled.
+
+config REALVIEW_EB_ARM1136
+	bool "Support ARM1136J(F)-S Tile"
+	depends on MACH_REALVIEW_EB && ARCH_MULTI_V6
+	select CPU_V6
+	help
+	  Enable support for the ARM1136 tile fitted to the
+	  Realview(R) Emulation Baseboard platform.
+
+config REALVIEW_EB_ARM1176
+	bool "Support ARM1176JZ(F)-S Tile"
+	depends on MACH_REALVIEW_EB && ARCH_MULTI_V6
+	help
+	  Enable support for the ARM1176 tile fitted to the
+	  Realview(R) Emulation Baseboard platform.
+
+config REALVIEW_EB_A9MP
+	bool "Support Multicore Cortex-A9 Tile"
+	depends on MACH_REALVIEW_EB && ARCH_MULTI_V7
+	help
+	  Enable support for the Cortex-A9MPCore tile fitted to the
+	  Realview(R) Emulation Baseboard platform.
+
+config REALVIEW_EB_ARM11MP
+	bool "Support ARM11MPCore Tile"
+	depends on MACH_REALVIEW_EB && ARCH_MULTI_V6
+	select HAVE_SMP
+	help
+	  Enable support for the ARM11MPCore tile fitted to the Realview(R)
+	  Emulation Baseboard platform.
+
+config MACH_REALVIEW_PB11MP
+	bool "Support RealView(R) Platform Baseboard for ARM11MPCore"
+	depends on ARCH_MULTI_V6
+	select HAVE_SMP
+	help
+	  Include support for the ARM(R) RealView(R) Platform Baseboard for
+	  the ARM11MPCore.  This platform has an on-board ARM11MPCore and has
+	  support for PCI-E and Compact Flash.
+
+# ARMv6 CPU without K extensions, but does have the new exclusive ops
+config MACH_REALVIEW_PB1176
+	bool "Support RealView(R) Platform Baseboard for ARM1176JZF-S"
+	depends on ARCH_MULTI_V6
+	select CPU_V6
+	select HAVE_TCM
+	help
+	  Include support for the ARM(R) RealView(R) Platform Baseboard for
+	  ARM1176JZF-S.
+
+config MACH_REALVIEW_PBA8
+	bool "Support RealView(R) Platform Baseboard for Cortex(tm)-A8 platform"
+	depends on ARCH_MULTI_V7
+	help
+	  Include support for the ARM(R) RealView Platform Baseboard for
+	  Cortex(tm)-A8.  This platform has an on-board Cortex-A8 and has
+	  support for PCI-E and Compact Flash.
+
+config MACH_REALVIEW_PBX
+	bool "Support RealView(R) Platform Baseboard Explore for Cortex-A9"
+	depends on ARCH_MULTI_V7
+	select ZONE_DMA
+	help
+	  Include support for the ARM(R) RealView(R) Platform Baseboard
+	  Explore.
+
+endif
+
+menuconfig ARCH_VEXPRESS
+	bool "ARM Ltd. Versatile Express family"
+	depends on ARCH_MULTI_V7
+	select ARM_AMBA
+	select ARM_GIC
+	select ARM_GLOBAL_TIMER
+	select ARM_TIMER_SP804
+	select GPIOLIB
+	select HAVE_ARM_SCU if SMP
+	select HAVE_ARM_TWD if SMP
+	select CLK_ICST
+	select NO_IOPORT_MAP
+	select PLAT_VERSATILE
+	select POWER_RESET
+	select POWER_RESET_VEXPRESS
+	select POWER_SUPPLY
+	select REGULATOR if MMC_ARMMMCI
+	select REGULATOR_FIXED_VOLTAGE if REGULATOR
+	select VEXPRESS_CONFIG
+	help
+	  This option enables support for systems using Cortex processor based
+	  ARM core and logic (FPGA) tiles on the Versatile Express motherboard,
+	  for example:
+
+	  - CoreTile Express A5x2 (V2P-CA5s)
+	  - CoreTile Express A9x4 (V2P-CA9)
+	  - CoreTile Express A15x2 (V2P-CA15)
+	  - LogicTile Express 13MG (V2F-2XV6) with A5, A7, A9 or A15 SMMs
+	    (Soft Macrocell Models)
+	  - Versatile Express RTSMs (Models)
+
+	  You must boot using a Flattened Device Tree in order to use these
+	  platforms. The traditional (ATAGs) boot method is not usable on
+	  these boards with this option.
+
+if ARCH_VEXPRESS
+
+config ARCH_VEXPRESS_CORTEX_A5_A9_ERRATA
+	bool "Enable A5 and A9 only errata work-arounds"
+	default y
+	select ARM_ERRATA_643719 if SMP
+	select ARM_ERRATA_720789
+	select PL310_ERRATA_753970 if CACHE_L2X0
+	help
+	  Provides common dependencies for Versatile Express platforms
+	  based on Cortex-A5 and Cortex-A9 processors. In order to
+	  build a working kernel, you must also enable relevant core
+	  tile support or Flattened Device Tree based support options.
+
+config ARCH_VEXPRESS_DCSCB
+	bool "Dual Cluster System Control Block (DCSCB) support"
+	depends on MCPM
+	select ARM_CCI400_PORT_CTRL
+	help
+	  Support for the Dual Cluster System Configuration Block (DCSCB).
+	  This is needed to provide CPU and cluster power management
+	  on RTSM implementing big.LITTLE.
+
+config ARCH_VEXPRESS_SPC
+	bool "Versatile Express Serial Power Controller (SPC)"
+	select PM_OPP
+	help
+	  The TC2 (A15x2 A7x3) versatile express core tile integrates a logic
+	  block called Serial Power Controller (SPC) that provides the interface
+	  between the dual cluster test-chip and the M3 microcontroller that
+	  carries out power management.
+
+config ARCH_VEXPRESS_TC2_PM
+	bool "Versatile Express TC2 power management"
+	depends on MCPM
+	select ARM_CCI400_PORT_CTRL
+	select ARCH_VEXPRESS_SPC
+	select ARM_CPU_SUSPEND
+	help
+	  Support for CPU and cluster power management on Versatile Express
+	  with a TC2 (A15x2 A7x3) big.LITTLE core tile.
+
+endif
diff --git a/arch/arm/mach-versatile/Makefile b/arch/arm/mach-versatile/Makefile
index 2b907718d467..27d712bcf1af 100644
--- a/arch/arm/mach-versatile/Makefile
+++ b/arch/arm/mach-versatile/Makefile
@@ -3,4 +3,34 @@
 # Makefile for the linux kernel.
 #
 
-obj-y					:= versatile_dt.o
+# versatile
+obj-$(CONFIG_ARCH_VERSATILE)		+= versatile.o
+
+# integrator
+obj-$(CONFIG_ARCH_INTEGRATOR)		+= integrator.o
+obj-$(CONFIG_ARCH_INTEGRATOR_AP)	+= integrator_ap.o
+obj-$(CONFIG_ARCH_INTEGRATOR_CP)	+= integrator_cp.o
+
+# realview
+obj-$(CONFIG_ARCH_REALVIEW)		+= realview.o
+
+# vexpress
+obj-$(CONFIG_ARCH_VEXPRESS)		:= v2m.o
+obj-$(CONFIG_ARCH_VEXPRESS_DCSCB)	+= dcscb.o	dcscb_setup.o
+CFLAGS_dcscb.o				+= -march=armv7-a
+CFLAGS_REMOVE_dcscb.o			= -pg
+obj-$(CONFIG_ARCH_VEXPRESS_SPC)		+= spc.o
+CFLAGS_REMOVE_spc.o			= -pg
+obj-$(CONFIG_ARCH_VEXPRESS_TC2_PM)	+= tc2_pm.o
+CFLAGS_tc2_pm.o				+= -march=armv7-a
+CFLAGS_REMOVE_tc2_pm.o			= -pg
+
+# mps2
+obj-$(CONFIG_ARCH_MPS2)			+= v2m-mps2.o
+
+ifdef CONFIG_SMP
+obj-y					+= headsmp.o platsmp.o
+obj-$(CONFIG_ARCH_REALVIEW)		+= platsmp-realview.o
+obj-$(CONFIG_ARCH_VEXPRESS)		+= platsmp-vexpress.o
+obj-$(CONFIG_HOTPLUG_CPU)		+= hotplug.o
+endif
diff --git a/arch/arm/mach-vexpress/dcscb.c b/arch/arm/mach-versatile/dcscb.c
index a0554d7d04f7..d8797350996d 100644
--- a/arch/arm/mach-vexpress/dcscb.c
+++ b/arch/arm/mach-versatile/dcscb.c
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * arch/arm/mach-vexpress/dcscb.c - Dual Cluster System Configuration Block
+ * dcscb.c - Dual Cluster System Configuration Block
  *
  * Created by:	Nicolas Pitre, May 2012
  * Copyright:	(C) 2012-2013  Linaro Limited
@@ -20,7 +20,7 @@
 #include <asm/cputype.h>
 #include <asm/cp15.h>
 
-#include "core.h"
+#include "vexpress.h"
 
 #define RST_HOLD0	0x0
 #define RST_HOLD1	0x4
@@ -144,6 +144,7 @@ static int __init dcscb_init(void)
 	if (!node)
 		return -ENODEV;
 	dcscb_base = of_iomap(node, 0);
+	of_node_put(node);
 	if (!dcscb_base)
 		return -EADDRNOTAVAIL;
 	cfg = readl_relaxed(dcscb_base + DCS_CFG_R);
diff --git a/arch/arm/mach-vexpress/dcscb_setup.S b/arch/arm/mach-versatile/dcscb_setup.S
index 0614b2ebd354..92d1fd9d7f6a 100644
--- a/arch/arm/mach-vexpress/dcscb_setup.S
+++ b/arch/arm/mach-versatile/dcscb_setup.S
@@ -1,7 +1,5 @@
 /* SPDX-License-Identifier: GPL-2.0-only */
 /*
- * arch/arm/include/asm/dcscb_setup.S
- *
  * Created by:  Dave Martin, 2012-06-22
  * Copyright:   (C) 2012-2013  Linaro Limited
  */
diff --git a/arch/arm/plat-versatile/headsmp.S b/arch/arm/mach-versatile/headsmp.S
index 09d9fc30c8ca..99c32db412ae 100644
--- a/arch/arm/plat-versatile/headsmp.S
+++ b/arch/arm/mach-versatile/headsmp.S
@@ -1,7 +1,5 @@
 /* SPDX-License-Identifier: GPL-2.0-only */
 /*
- *  linux/arch/arm/plat-versatile/headsmp.S
- *
  *  Copyright (c) 2003 ARM Limited
  *  All Rights Reserved
  */
diff --git a/arch/arm/plat-versatile/hotplug.c b/arch/arm/mach-versatile/hotplug.c
index 2e9dca38bec0..5a152175578b 100644
--- a/arch/arm/plat-versatile/hotplug.c
+++ b/arch/arm/mach-versatile/hotplug.c
@@ -15,7 +15,7 @@
 #include <asm/smp_plat.h>
 #include <asm/cp15.h>
 
-#include <plat/platsmp.h>
+#include "platsmp.h"
 
 static inline void versatile_immitation_enter_lowpower(unsigned int actrl_mask)
 {
diff --git a/arch/arm/mach-integrator/cm.h b/arch/arm/mach-versatile/integrator-cm.h
index f09ea18a50f8..f09ea18a50f8 100644
--- a/arch/arm/mach-integrator/cm.h
+++ b/arch/arm/mach-versatile/integrator-cm.h
diff --git a/arch/arm/mach-versatile/integrator-hardware.h b/arch/arm/mach-versatile/integrator-hardware.h
new file mode 100644
index 000000000000..81ce09e3ad45
--- /dev/null
+++ b/arch/arm/mach-versatile/integrator-hardware.h
@@ -0,0 +1,336 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ *  This file contains the hardware definitions of the Integrator.
+ *
+ *  Copyright (C) 1998-1999 ARM Limited.
+ */
+#ifndef INTEGRATOR_HARDWARE_H
+#define INTEGRATOR_HARDWARE_H
+
+/*
+ * Where in virtual memory the IO devices (timers, system controllers
+ * and so on)
+ */
+#define IO_BASE			0xF0000000                 // VA of IO
+#define IO_SIZE			0x0B000000                 // How much?
+#define IO_START		INTEGRATOR_HDR_BASE        // PA of IO
+
+/* macro to get at IO space when running virtually */
+#define IO_ADDRESS(x)	(((x) & 0x000fffff) | (((x) >> 4) & 0x0ff00000) | IO_BASE)
+#define __io_address(n)		((void __iomem *)IO_ADDRESS(n))
+
+/*
+ *  Integrator memory map
+ */
+#define INTEGRATOR_BOOT_ROM_LO          0x00000000
+#define INTEGRATOR_BOOT_ROM_HI          0x20000000
+#define INTEGRATOR_BOOT_ROM_BASE        INTEGRATOR_BOOT_ROM_HI	 /*  Normal position */
+#define INTEGRATOR_BOOT_ROM_SIZE        SZ_512K
+
+/*
+ * New Core Modules have different amounts of SSRAM, the amount of SSRAM
+ * fitted can be found in HDR_STAT.
+ *
+ * The symbol INTEGRATOR_SSRAM_SIZE is kept, however this now refers to
+ * the minimum amount of SSRAM fitted on any core module.
+ *
+ * New Core Modules also alias the SSRAM.
+ *
+ */
+#define INTEGRATOR_SSRAM_BASE           0x00000000
+#define INTEGRATOR_SSRAM_ALIAS_BASE     0x10800000
+#define INTEGRATOR_SSRAM_SIZE           SZ_256K
+
+#define INTEGRATOR_FLASH_BASE           0x24000000
+#define INTEGRATOR_FLASH_SIZE           SZ_32M
+
+#define INTEGRATOR_MBRD_SSRAM_BASE      0x28000000
+#define INTEGRATOR_MBRD_SSRAM_SIZE      SZ_512K
+
+/*
+ *  SDRAM is a SIMM therefore the size is not known.
+ */
+#define INTEGRATOR_SDRAM_BASE           0x00040000
+
+#define INTEGRATOR_SDRAM_ALIAS_BASE     0x80000000
+#define INTEGRATOR_HDR0_SDRAM_BASE      0x80000000
+#define INTEGRATOR_HDR1_SDRAM_BASE      0x90000000
+#define INTEGRATOR_HDR2_SDRAM_BASE      0xA0000000
+#define INTEGRATOR_HDR3_SDRAM_BASE      0xB0000000
+
+/*
+ *  Logic expansion modules
+ *
+ */
+#define INTEGRATOR_LOGIC_MODULES_BASE   0xC0000000
+#define INTEGRATOR_LOGIC_MODULE0_BASE   0xC0000000
+#define INTEGRATOR_LOGIC_MODULE1_BASE   0xD0000000
+#define INTEGRATOR_LOGIC_MODULE2_BASE   0xE0000000
+#define INTEGRATOR_LOGIC_MODULE3_BASE   0xF0000000
+
+/*
+ * Integrator header card registers
+ */
+#define INTEGRATOR_HDR_ID_OFFSET        0x00
+#define INTEGRATOR_HDR_PROC_OFFSET      0x04
+#define INTEGRATOR_HDR_OSC_OFFSET       0x08
+#define INTEGRATOR_HDR_CTRL_OFFSET      0x0C
+#define INTEGRATOR_HDR_STAT_OFFSET      0x10
+#define INTEGRATOR_HDR_LOCK_OFFSET      0x14
+#define INTEGRATOR_HDR_SDRAM_OFFSET     0x20
+#define INTEGRATOR_HDR_INIT_OFFSET      0x24	 /*  CM9x6 */
+#define INTEGRATOR_HDR_IC_OFFSET        0x40
+#define INTEGRATOR_HDR_SPDBASE_OFFSET   0x100
+#define INTEGRATOR_HDR_SPDTOP_OFFSET    0x200
+
+#define INTEGRATOR_HDR_BASE             0x10000000
+#define INTEGRATOR_HDR_ID               (INTEGRATOR_HDR_BASE + INTEGRATOR_HDR_ID_OFFSET)
+#define INTEGRATOR_HDR_PROC             (INTEGRATOR_HDR_BASE + INTEGRATOR_HDR_PROC_OFFSET)
+#define INTEGRATOR_HDR_OSC              (INTEGRATOR_HDR_BASE + INTEGRATOR_HDR_OSC_OFFSET)
+#define INTEGRATOR_HDR_CTRL             (INTEGRATOR_HDR_BASE + INTEGRATOR_HDR_CTRL_OFFSET)
+#define INTEGRATOR_HDR_STAT             (INTEGRATOR_HDR_BASE + INTEGRATOR_HDR_STAT_OFFSET)
+#define INTEGRATOR_HDR_LOCK             (INTEGRATOR_HDR_BASE + INTEGRATOR_HDR_LOCK_OFFSET)
+#define INTEGRATOR_HDR_SDRAM            (INTEGRATOR_HDR_BASE + INTEGRATOR_HDR_SDRAM_OFFSET)
+#define INTEGRATOR_HDR_INIT             (INTEGRATOR_HDR_BASE + INTEGRATOR_HDR_INIT_OFFSET)
+#define INTEGRATOR_HDR_IC               (INTEGRATOR_HDR_BASE + INTEGRATOR_HDR_IC_OFFSET)
+#define INTEGRATOR_HDR_SPDBASE          (INTEGRATOR_HDR_BASE + INTEGRATOR_HDR_SPDBASE_OFFSET)
+#define INTEGRATOR_HDR_SPDTOP           (INTEGRATOR_HDR_BASE + INTEGRATOR_HDR_SPDTOP_OFFSET)
+
+#define INTEGRATOR_HDR_CTRL_LED         0x01
+#define INTEGRATOR_HDR_CTRL_MBRD_DETECH 0x02
+#define INTEGRATOR_HDR_CTRL_REMAP       0x04
+#define INTEGRATOR_HDR_CTRL_RESET       0x08
+#define INTEGRATOR_HDR_CTRL_HIGHVECTORS 0x10
+#define INTEGRATOR_HDR_CTRL_BIG_ENDIAN  0x20
+#define INTEGRATOR_HDR_CTRL_FASTBUS     0x40
+#define INTEGRATOR_HDR_CTRL_SYNC        0x80
+
+#define INTEGRATOR_HDR_OSC_CORE_10MHz   0x102
+#define INTEGRATOR_HDR_OSC_CORE_15MHz   0x107
+#define INTEGRATOR_HDR_OSC_CORE_20MHz   0x10C
+#define INTEGRATOR_HDR_OSC_CORE_25MHz   0x111
+#define INTEGRATOR_HDR_OSC_CORE_30MHz   0x116
+#define INTEGRATOR_HDR_OSC_CORE_35MHz   0x11B
+#define INTEGRATOR_HDR_OSC_CORE_40MHz   0x120
+#define INTEGRATOR_HDR_OSC_CORE_45MHz   0x125
+#define INTEGRATOR_HDR_OSC_CORE_50MHz   0x12A
+#define INTEGRATOR_HDR_OSC_CORE_55MHz   0x12F
+#define INTEGRATOR_HDR_OSC_CORE_60MHz   0x134
+#define INTEGRATOR_HDR_OSC_CORE_65MHz   0x139
+#define INTEGRATOR_HDR_OSC_CORE_70MHz   0x13E
+#define INTEGRATOR_HDR_OSC_CORE_75MHz   0x143
+#define INTEGRATOR_HDR_OSC_CORE_80MHz   0x148
+#define INTEGRATOR_HDR_OSC_CORE_85MHz   0x14D
+#define INTEGRATOR_HDR_OSC_CORE_90MHz   0x152
+#define INTEGRATOR_HDR_OSC_CORE_95MHz   0x157
+#define INTEGRATOR_HDR_OSC_CORE_100MHz  0x15C
+#define INTEGRATOR_HDR_OSC_CORE_105MHz  0x161
+#define INTEGRATOR_HDR_OSC_CORE_110MHz  0x166
+#define INTEGRATOR_HDR_OSC_CORE_115MHz  0x16B
+#define INTEGRATOR_HDR_OSC_CORE_120MHz  0x170
+#define INTEGRATOR_HDR_OSC_CORE_125MHz  0x175
+#define INTEGRATOR_HDR_OSC_CORE_130MHz  0x17A
+#define INTEGRATOR_HDR_OSC_CORE_135MHz  0x17F
+#define INTEGRATOR_HDR_OSC_CORE_140MHz  0x184
+#define INTEGRATOR_HDR_OSC_CORE_145MHz  0x189
+#define INTEGRATOR_HDR_OSC_CORE_150MHz  0x18E
+#define INTEGRATOR_HDR_OSC_CORE_155MHz  0x193
+#define INTEGRATOR_HDR_OSC_CORE_160MHz  0x198
+#define INTEGRATOR_HDR_OSC_CORE_MASK    0x7FF
+
+#define INTEGRATOR_HDR_OSC_MEM_10MHz    0x10C000
+#define INTEGRATOR_HDR_OSC_MEM_15MHz    0x116000
+#define INTEGRATOR_HDR_OSC_MEM_20MHz    0x120000
+#define INTEGRATOR_HDR_OSC_MEM_25MHz    0x12A000
+#define INTEGRATOR_HDR_OSC_MEM_30MHz    0x134000
+#define INTEGRATOR_HDR_OSC_MEM_33MHz    0x13A000
+#define INTEGRATOR_HDR_OSC_MEM_40MHz    0x148000
+#define INTEGRATOR_HDR_OSC_MEM_50MHz    0x15C000
+#define INTEGRATOR_HDR_OSC_MEM_60MHz    0x170000
+#define INTEGRATOR_HDR_OSC_MEM_66MHz    0x17C000
+#define INTEGRATOR_HDR_OSC_MEM_MASK     0x7FF000
+
+#define INTEGRATOR_HDR_OSC_BUS_MODE_CM7x0  0x0
+#define INTEGRATOR_HDR_OSC_BUS_MODE_CM9x0  0x0800000
+#define INTEGRATOR_HDR_OSC_BUS_MODE_CM9x6  0x1000000
+#define INTEGRATOR_HDR_OSC_BUS_MODE_CM10x00  0x1800000
+#define INTEGRATOR_HDR_OSC_BUS_MODE_MASK  0x1800000
+
+#define INTEGRATOR_HDR_SDRAM_SPD_OK     (1 << 5)
+
+/*
+ * Integrator system registers
+ */
+
+/*
+ *  System Controller
+ */
+#define INTEGRATOR_SC_ID_OFFSET         0x00
+#define INTEGRATOR_SC_OSC_OFFSET        0x04
+#define INTEGRATOR_SC_CTRLS_OFFSET      0x08
+#define INTEGRATOR_SC_CTRLC_OFFSET      0x0C
+#define INTEGRATOR_SC_DEC_OFFSET        0x10
+#define INTEGRATOR_SC_ARB_OFFSET        0x14
+#define INTEGRATOR_SC_LOCK_OFFSET       0x1C
+
+#define INTEGRATOR_SC_BASE              0x11000000
+#define INTEGRATOR_SC_ID                (INTEGRATOR_SC_BASE + INTEGRATOR_SC_ID_OFFSET)
+#define INTEGRATOR_SC_OSC               (INTEGRATOR_SC_BASE + INTEGRATOR_SC_OSC_OFFSET)
+#define INTEGRATOR_SC_CTRLS             (INTEGRATOR_SC_BASE + INTEGRATOR_SC_CTRLS_OFFSET)
+#define INTEGRATOR_SC_CTRLC             (INTEGRATOR_SC_BASE + INTEGRATOR_SC_CTRLC_OFFSET)
+#define INTEGRATOR_SC_DEC               (INTEGRATOR_SC_BASE + INTEGRATOR_SC_DEC_OFFSET)
+#define INTEGRATOR_SC_ARB               (INTEGRATOR_SC_BASE + INTEGRATOR_SC_ARB_OFFSET)
+#define INTEGRATOR_SC_PCIENABLE         (INTEGRATOR_SC_BASE + INTEGRATOR_SC_PCIENABLE_OFFSET)
+#define INTEGRATOR_SC_LOCK              (INTEGRATOR_SC_BASE + INTEGRATOR_SC_LOCK_OFFSET)
+
+#define INTEGRATOR_SC_OSC_SYS_10MHz     0x20
+#define INTEGRATOR_SC_OSC_SYS_15MHz     0x34
+#define INTEGRATOR_SC_OSC_SYS_20MHz     0x48
+#define INTEGRATOR_SC_OSC_SYS_25MHz     0x5C
+#define INTEGRATOR_SC_OSC_SYS_33MHz     0x7C
+#define INTEGRATOR_SC_OSC_SYS_MASK      0xFF
+
+#define INTEGRATOR_SC_OSC_PCI_25MHz     0x100
+#define INTEGRATOR_SC_OSC_PCI_33MHz     0x0
+#define INTEGRATOR_SC_OSC_PCI_MASK      0x100
+
+#define INTEGRATOR_SC_CTRL_SOFTRST      (1 << 0)
+#define INTEGRATOR_SC_CTRL_nFLVPPEN     (1 << 1)
+#define INTEGRATOR_SC_CTRL_nFLWP        (1 << 2)
+#define INTEGRATOR_SC_CTRL_URTS0        (1 << 4)
+#define INTEGRATOR_SC_CTRL_UDTR0        (1 << 5)
+#define INTEGRATOR_SC_CTRL_URTS1        (1 << 6)
+#define INTEGRATOR_SC_CTRL_UDTR1        (1 << 7)
+
+/*
+ *  External Bus Interface
+ */
+#define INTEGRATOR_EBI_BASE             0x12000000
+
+#define INTEGRATOR_EBI_CSR0_OFFSET      0x00
+#define INTEGRATOR_EBI_CSR1_OFFSET      0x04
+#define INTEGRATOR_EBI_CSR2_OFFSET      0x08
+#define INTEGRATOR_EBI_CSR3_OFFSET      0x0C
+#define INTEGRATOR_EBI_LOCK_OFFSET      0x20
+
+#define INTEGRATOR_EBI_CSR0             (INTEGRATOR_EBI_BASE + INTEGRATOR_EBI_CSR0_OFFSET)
+#define INTEGRATOR_EBI_CSR1             (INTEGRATOR_EBI_BASE + INTEGRATOR_EBI_CSR1_OFFSET)
+#define INTEGRATOR_EBI_CSR2             (INTEGRATOR_EBI_BASE + INTEGRATOR_EBI_CSR2_OFFSET)
+#define INTEGRATOR_EBI_CSR3             (INTEGRATOR_EBI_BASE + INTEGRATOR_EBI_CSR3_OFFSET)
+#define INTEGRATOR_EBI_LOCK             (INTEGRATOR_EBI_BASE + INTEGRATOR_EBI_LOCK_OFFSET)
+
+#define INTEGRATOR_EBI_8_BIT            0x00
+#define INTEGRATOR_EBI_16_BIT           0x01
+#define INTEGRATOR_EBI_32_BIT           0x02
+#define INTEGRATOR_EBI_WRITE_ENABLE     0x04
+#define INTEGRATOR_EBI_SYNC             0x08
+#define INTEGRATOR_EBI_WS_2             0x00
+#define INTEGRATOR_EBI_WS_3             0x10
+#define INTEGRATOR_EBI_WS_4             0x20
+#define INTEGRATOR_EBI_WS_5             0x30
+#define INTEGRATOR_EBI_WS_6             0x40
+#define INTEGRATOR_EBI_WS_7             0x50
+#define INTEGRATOR_EBI_WS_8             0x60
+#define INTEGRATOR_EBI_WS_9             0x70
+#define INTEGRATOR_EBI_WS_10            0x80
+#define INTEGRATOR_EBI_WS_11            0x90
+#define INTEGRATOR_EBI_WS_12            0xA0
+#define INTEGRATOR_EBI_WS_13            0xB0
+#define INTEGRATOR_EBI_WS_14            0xC0
+#define INTEGRATOR_EBI_WS_15            0xD0
+#define INTEGRATOR_EBI_WS_16            0xE0
+#define INTEGRATOR_EBI_WS_17            0xF0
+
+
+#define INTEGRATOR_CT_BASE              0x13000000	 /*  Counter/Timers */
+#define INTEGRATOR_IC_BASE              0x14000000	 /*  Interrupt Controller */
+#define INTEGRATOR_RTC_BASE             0x15000000	 /*  Real Time Clock */
+#define INTEGRATOR_UART0_BASE           0x16000000	 /*  UART 0 */
+#define INTEGRATOR_UART1_BASE           0x17000000	 /*  UART 1 */
+#define INTEGRATOR_KBD_BASE             0x18000000	 /*  Keyboard */
+#define INTEGRATOR_MOUSE_BASE           0x19000000	 /*  Mouse */
+
+/*
+ *  LED's & Switches
+ */
+#define INTEGRATOR_DBG_ALPHA_OFFSET     0x00
+#define INTEGRATOR_DBG_LEDS_OFFSET      0x04
+#define INTEGRATOR_DBG_SWITCH_OFFSET    0x08
+
+#define INTEGRATOR_DBG_BASE             0x1A000000
+#define INTEGRATOR_DBG_ALPHA            (INTEGRATOR_DBG_BASE + INTEGRATOR_DBG_ALPHA_OFFSET)
+#define INTEGRATOR_DBG_LEDS             (INTEGRATOR_DBG_BASE + INTEGRATOR_DBG_LEDS_OFFSET)
+#define INTEGRATOR_DBG_SWITCH           (INTEGRATOR_DBG_BASE + INTEGRATOR_DBG_SWITCH_OFFSET)
+
+#define INTEGRATOR_AP_GPIO_BASE		0x1B000000	/* GPIO */
+
+#define INTEGRATOR_CP_MMC_BASE		0x1C000000	/* MMC */
+#define INTEGRATOR_CP_AACI_BASE		0x1D000000	/* AACI */
+#define INTEGRATOR_CP_ETH_BASE		0xC8000000	/* Ethernet */
+#define INTEGRATOR_CP_GPIO_BASE		0xC9000000	/* GPIO */
+#define INTEGRATOR_CP_SIC_BASE		0xCA000000	/* SIC */
+#define INTEGRATOR_CP_CTL_BASE		0xCB000000	/* CP system control */
+
+/* PS2 Keyboard interface */
+#define KMI0_BASE                       INTEGRATOR_KBD_BASE
+
+/* PS2 Mouse interface */
+#define KMI1_BASE                       INTEGRATOR_MOUSE_BASE
+
+/*
+ * Integrator Interrupt Controllers
+ *
+ *
+ * Offsets from interrupt controller base
+ *
+ * System Controller interrupt controller base is
+ *
+ * 	INTEGRATOR_IC_BASE + (header_number << 6)
+ *
+ * Core Module interrupt controller base is
+ *
+ * 	INTEGRATOR_HDR_IC
+ */
+#define IRQ_STATUS                      0
+#define IRQ_RAW_STATUS                  0x04
+#define IRQ_ENABLE                      0x08
+#define IRQ_ENABLE_SET                  0x08
+#define IRQ_ENABLE_CLEAR                0x0C
+
+#define INT_SOFT_SET                    0x10
+#define INT_SOFT_CLEAR                  0x14
+
+#define FIQ_STATUS                      0x20
+#define FIQ_RAW_STATUS                  0x24
+#define FIQ_ENABLE                      0x28
+#define FIQ_ENABLE_SET                  0x28
+#define FIQ_ENABLE_CLEAR                0x2C
+
+
+/*
+ * LED's
+ */
+#define GREEN_LED                       0x01
+#define YELLOW_LED                      0x02
+#define RED_LED                         0x04
+#define GREEN_LED_2                     0x08
+#define ALL_LEDS                        0x0F
+
+#define LED_BANK                        INTEGRATOR_DBG_LEDS
+
+/*
+ *  Timer definitions
+ *
+ *  Only use timer 1 & 2
+ *  (both run at 24MHz and will need the clock divider set to 16).
+ *
+ *  Timer 0 runs at bus frequency
+ */
+#define INTEGRATOR_TIMER0_BASE          INTEGRATOR_CT_BASE
+#define INTEGRATOR_TIMER1_BASE          (INTEGRATOR_CT_BASE + 0x100)
+#define INTEGRATOR_TIMER2_BASE          (INTEGRATOR_CT_BASE + 0x200)
+
+#define INTEGRATOR_CSR_BASE             0x10000000
+#define INTEGRATOR_CSR_SIZE             0x10000000
+
+#endif /* INTEGRATOR_HARDWARE_H */
diff --git a/arch/arm/mach-versatile/integrator.c b/arch/arm/mach-versatile/integrator.c
new file mode 100644
index 000000000000..fdf9c4db08a7
--- /dev/null
+++ b/arch/arm/mach-versatile/integrator.c
@@ -0,0 +1,94 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ *  Copyright (C) 2000-2003 Deep Blue Solutions Ltd
+ */
+#include <linux/types.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/device.h>
+#include <linux/export.h>
+#include <linux/spinlock.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/memblock.h>
+#include <linux/sched.h>
+#include <linux/smp.h>
+#include <linux/amba/bus.h>
+#include <linux/amba/serial.h>
+#include <linux/io.h>
+#include <linux/stat.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/pgtable.h>
+
+#include <asm/mach-types.h>
+#include <asm/mach/time.h>
+
+#include "integrator-hardware.h"
+#include "integrator-cm.h"
+#include "integrator.h"
+
+static DEFINE_RAW_SPINLOCK(cm_lock);
+static void __iomem *cm_base;
+
+/**
+ * cm_get - get the value from the CM_CTRL register
+ */
+u32 cm_get(void)
+{
+	return readl(cm_base + INTEGRATOR_HDR_CTRL_OFFSET);
+}
+
+/**
+ * cm_control - update the CM_CTRL register.
+ * @mask: bits to change
+ * @set: bits to set
+ */
+void cm_control(u32 mask, u32 set)
+{
+	unsigned long flags;
+	u32 val;
+
+	raw_spin_lock_irqsave(&cm_lock, flags);
+	val = readl(cm_base + INTEGRATOR_HDR_CTRL_OFFSET) & ~mask;
+	writel(val | set, cm_base + INTEGRATOR_HDR_CTRL_OFFSET);
+	raw_spin_unlock_irqrestore(&cm_lock, flags);
+}
+
+void cm_clear_irqs(void)
+{
+	/* disable core module IRQs */
+	writel(0xffffffffU, cm_base + INTEGRATOR_HDR_IC_OFFSET +
+		IRQ_ENABLE_CLEAR);
+}
+
+static const struct of_device_id cm_match[] = {
+	{ .compatible = "arm,core-module-integrator"},
+	{ },
+};
+
+void cm_init(void)
+{
+	struct device_node *cm = of_find_matching_node(NULL, cm_match);
+
+	if (!cm) {
+		pr_crit("no core module node found in device tree\n");
+		return;
+	}
+	cm_base = of_iomap(cm, 0);
+	if (!cm_base) {
+		pr_crit("could not remap core module\n");
+		return;
+	}
+	cm_clear_irqs();
+}
+
+/*
+ * We need to stop things allocating the low memory; ideally we need a
+ * better implementation of GFP_DMA which does not assume that DMA-able
+ * memory starts at zero.
+ */
+void __init integrator_reserve(void)
+{
+	memblock_reserve(PHYS_OFFSET, __pa(swapper_pg_dir) - PHYS_OFFSET);
+}
diff --git a/arch/arm/mach-integrator/common.h b/arch/arm/mach-versatile/integrator.h
index f053aeebeb7a..f053aeebeb7a 100644
--- a/arch/arm/mach-integrator/common.h
+++ b/arch/arm/mach-versatile/integrator.h
diff --git a/arch/arm/mach-integrator/integrator_ap.c b/arch/arm/mach-versatile/integrator_ap.c
index 58b02cbbea72..4bd6712e9f52 100644
--- a/arch/arm/mach-integrator/integrator_ap.c
+++ b/arch/arm/mach-versatile/integrator_ap.c
@@ -1,7 +1,5 @@
 // SPDX-License-Identifier: GPL-2.0-or-later
 /*
- *  linux/arch/arm/mach-integrator/integrator_ap.c
- *
  *  Copyright (C) 2000-2003 Deep Blue Solutions Ltd
  */
 #include <linux/kernel.h>
@@ -13,6 +11,7 @@
 #include <linux/of_irq.h>
 #include <linux/of_address.h>
 #include <linux/of_platform.h>
+#include <linux/uaccess.h>
 #include <linux/termios.h>
 #include <linux/mfd/syscon.h>
 #include <linux/regmap.h>
@@ -20,9 +19,9 @@
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
 
-#include "hardware.h"
-#include "cm.h"
-#include "common.h"
+#include "integrator-hardware.h"
+#include "integrator-cm.h"
+#include "integrator.h"
 
 /* Regmap to the AP system controller */
 static struct regmap *ap_syscon_map;
@@ -147,10 +146,6 @@ struct amba_pl010_data ap_uart_data = {
 	.set_mctrl = integrator_uart_set_mctrl,
 };
 
-void __init ap_init_early(void)
-{
-}
-
 static void __init ap_init_irq_of(void)
 {
 	cm_init();
@@ -195,7 +190,6 @@ static const char * ap_dt_board_compat[] = {
 DT_MACHINE_START(INTEGRATOR_AP_DT, "ARM Integrator/AP (Device Tree)")
 	.reserve	= integrator_reserve,
 	.map_io		= ap_map_io,
-	.init_early	= ap_init_early,
 	.init_irq	= ap_init_irq_of,
 	.init_machine	= ap_init_of,
 	.dt_compat      = ap_dt_board_compat,
diff --git a/arch/arm/mach-integrator/integrator_cp.c b/arch/arm/mach-versatile/integrator_cp.c
index b7eb4038798b..2ed4ded56b3f 100644
--- a/arch/arm/mach-integrator/integrator_cp.c
+++ b/arch/arm/mach-versatile/integrator_cp.c
@@ -1,7 +1,5 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- *  linux/arch/arm/mach-integrator/integrator_cp.c
- *
  *  Copyright (C) 2003 Deep Blue Solutions Ltd
  */
 #include <linux/kernel.h>
@@ -18,9 +16,9 @@
 #include <asm/mach/arch.h>
 #include <asm/mach/map.h>
 
-#include "hardware.h"
-#include "cm.h"
-#include "common.h"
+#include "integrator-hardware.h"
+#include "integrator-cm.h"
+#include "integrator.h"
 
 /* Base address to the core module header */
 static struct regmap *cm_map;
diff --git a/arch/arm/mach-versatile/platsmp-realview.c b/arch/arm/mach-versatile/platsmp-realview.c
new file mode 100644
index 000000000000..5d363385c801
--- /dev/null
+++ b/arch/arm/mach-versatile/platsmp-realview.c
@@ -0,0 +1,93 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2015 Linus Walleij
+ */
+#include <linux/smp.h>
+#include <linux/io.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/regmap.h>
+#include <linux/mfd/syscon.h>
+
+#include <asm/cacheflush.h>
+#include <asm/smp_plat.h>
+#include <asm/smp_scu.h>
+
+#include "platsmp.h"
+
+#define REALVIEW_SYS_FLAGSSET_OFFSET	0x30
+
+static const struct of_device_id realview_scu_match[] = {
+	{ .compatible = "arm,arm11mp-scu", },
+	{ .compatible = "arm,cortex-a9-scu", },
+	{ .compatible = "arm,cortex-a5-scu", },
+	{ }
+};
+
+static const struct of_device_id realview_syscon_match[] = {
+        { .compatible = "arm,core-module-integrator", },
+        { .compatible = "arm,realview-eb-syscon", },
+        { .compatible = "arm,realview-pb11mp-syscon", },
+        { .compatible = "arm,realview-pbx-syscon", },
+        { },
+};
+
+static void __init realview_smp_prepare_cpus(unsigned int max_cpus)
+{
+	struct device_node *np;
+	void __iomem *scu_base;
+	struct regmap *map;
+	unsigned int ncores;
+	int i;
+
+	np = of_find_matching_node(NULL, realview_scu_match);
+	if (!np) {
+		pr_err("PLATSMP: No SCU base address\n");
+		return;
+	}
+	scu_base = of_iomap(np, 0);
+	of_node_put(np);
+	if (!scu_base) {
+		pr_err("PLATSMP: No SCU remap\n");
+		return;
+	}
+
+	scu_enable(scu_base);
+	ncores = scu_get_core_count(scu_base);
+	pr_info("SCU: %d cores detected\n", ncores);
+	for (i = 0; i < ncores; i++)
+		set_cpu_possible(i, true);
+	iounmap(scu_base);
+
+	/* The syscon contains the magic SMP start address registers */
+	np = of_find_matching_node(NULL, realview_syscon_match);
+	if (!np) {
+		pr_err("PLATSMP: No syscon match\n");
+		return;
+	}
+	map = syscon_node_to_regmap(np);
+	if (IS_ERR(map)) {
+		pr_err("PLATSMP: No syscon regmap\n");
+		return;
+	}
+	/* Put the boot address in this magic register */
+	regmap_write(map, REALVIEW_SYS_FLAGSSET_OFFSET,
+		     __pa_symbol(versatile_secondary_startup));
+}
+
+#ifdef CONFIG_HOTPLUG_CPU
+static void realview_cpu_die(unsigned int cpu)
+{
+	return versatile_immitation_cpu_die(cpu, 0x20);
+}
+#endif
+
+static const struct smp_operations realview_dt_smp_ops __initconst = {
+	.smp_prepare_cpus	= realview_smp_prepare_cpus,
+	.smp_secondary_init	= versatile_secondary_init,
+	.smp_boot_secondary	= versatile_boot_secondary,
+#ifdef CONFIG_HOTPLUG_CPU
+	.cpu_die		= realview_cpu_die,
+#endif
+};
+CPU_METHOD_OF_DECLARE(realview_smp, "arm,realview-smp", &realview_dt_smp_ops);
diff --git a/arch/arm/mach-versatile/platsmp-vexpress.c b/arch/arm/mach-versatile/platsmp-vexpress.c
new file mode 100644
index 000000000000..1ee3c45e71c9
--- /dev/null
+++ b/arch/arm/mach-versatile/platsmp-vexpress.c
@@ -0,0 +1,93 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ *  Copyright (C) 2002 ARM Ltd.
+ *  All Rights Reserved
+ */
+#include <linux/init.h>
+#include <linux/errno.h>
+#include <linux/smp.h>
+#include <linux/io.h>
+#include <linux/of_address.h>
+#include <linux/vexpress.h>
+
+#include <asm/mcpm.h>
+#include <asm/smp_scu.h>
+#include <asm/mach/map.h>
+
+#include "platsmp.h"
+#include "vexpress.h"
+
+bool __init vexpress_smp_init_ops(void)
+{
+#ifdef CONFIG_MCPM
+	int cpu;
+	struct device_node *cpu_node, *cci_node;
+
+	/*
+	 * The best way to detect a multi-cluster configuration
+	 * is to detect if the kernel can take over CCI ports
+	 * control. Loop over possible CPUs and check if CCI
+	 * port control is available.
+	 * Override the default vexpress_smp_ops if so.
+	 */
+	for_each_possible_cpu(cpu) {
+		bool available;
+
+		cpu_node = of_get_cpu_node(cpu, NULL);
+		if (WARN(!cpu_node, "Missing cpu device node!"))
+			return false;
+
+		cci_node = of_parse_phandle(cpu_node, "cci-control-port", 0);
+		available = cci_node && of_device_is_available(cci_node);
+		of_node_put(cci_node);
+		of_node_put(cpu_node);
+
+		if (!available)
+			return false;
+	}
+
+	mcpm_smp_set_ops();
+	return true;
+#else
+	return false;
+#endif
+}
+
+static const struct of_device_id vexpress_smp_dt_scu_match[] __initconst = {
+	{ .compatible = "arm,cortex-a5-scu", },
+	{ .compatible = "arm,cortex-a9-scu", },
+	{}
+};
+
+static void __init vexpress_smp_dt_prepare_cpus(unsigned int max_cpus)
+{
+	struct device_node *scu = of_find_matching_node(NULL,
+			vexpress_smp_dt_scu_match);
+
+	if (scu)
+		scu_enable(of_iomap(scu, 0));
+
+	/*
+	 * Write the address of secondary startup into the
+	 * system-wide flags register. The boot monitor waits
+	 * until it receives a soft interrupt, and then the
+	 * secondary CPU branches to this address.
+	 */
+	vexpress_flags_set(__pa_symbol(versatile_secondary_startup));
+}
+
+#ifdef CONFIG_HOTPLUG_CPU
+static void vexpress_cpu_die(unsigned int cpu)
+{
+	versatile_immitation_cpu_die(cpu, 0x40);
+}
+#endif
+
+const struct smp_operations vexpress_smp_dt_ops __initconst = {
+	.smp_prepare_cpus	= vexpress_smp_dt_prepare_cpus,
+	.smp_secondary_init	= versatile_secondary_init,
+	.smp_boot_secondary	= versatile_boot_secondary,
+#ifdef CONFIG_HOTPLUG_CPU
+	.cpu_die		= vexpress_cpu_die,
+#endif
+};
diff --git a/arch/arm/mach-versatile/platsmp.c b/arch/arm/mach-versatile/platsmp.c
new file mode 100644
index 000000000000..fa7378321e23
--- /dev/null
+++ b/arch/arm/mach-versatile/platsmp.c
@@ -0,0 +1,107 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ *  Copyright (C) 2002 ARM Ltd.
+ *  All Rights Reserved
+ *
+ * This code is specific to the hardware found on ARM Realview and
+ * Versatile Express platforms where the CPUs are unable to be individually
+ * woken, and where there is no way to hot-unplug CPUs.  Real platforms
+ * should not copy this code.
+ */
+#include <linux/init.h>
+#include <linux/errno.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/jiffies.h>
+#include <linux/smp.h>
+
+#include <asm/cacheflush.h>
+#include <asm/smp_plat.h>
+
+#include "platsmp.h"
+
+/*
+ * versatile_cpu_release controls the release of CPUs from the holding
+ * pen in headsmp.S, which exists because we are not always able to
+ * control the release of individual CPUs from the board firmware.
+ * Production platforms do not need this.
+ */
+volatile int versatile_cpu_release = -1;
+
+/*
+ * Write versatile_cpu_release in a way that is guaranteed to be visible to
+ * all observers, irrespective of whether they're taking part in coherency
+ * or not.  This is necessary for the hotplug code to work reliably.
+ */
+static void versatile_write_cpu_release(int val)
+{
+	versatile_cpu_release = val;
+	smp_wmb();
+	sync_cache_w(&versatile_cpu_release);
+}
+
+/*
+ * versatile_lock exists to avoid running the loops_per_jiffy delay loop
+ * calibrations on the secondary CPU while the requesting CPU is using
+ * the limited-bandwidth bus - which affects the calibration value.
+ * Production platforms do not need this.
+ */
+static DEFINE_RAW_SPINLOCK(versatile_lock);
+
+void versatile_secondary_init(unsigned int cpu)
+{
+	/*
+	 * let the primary processor know we're out of the
+	 * pen, then head off into the C entry point
+	 */
+	versatile_write_cpu_release(-1);
+
+	/*
+	 * Synchronise with the boot thread.
+	 */
+	raw_spin_lock(&versatile_lock);
+	raw_spin_unlock(&versatile_lock);
+}
+
+int versatile_boot_secondary(unsigned int cpu, struct task_struct *idle)
+{
+	unsigned long timeout;
+
+	/*
+	 * Set synchronisation state between this boot processor
+	 * and the secondary one
+	 */
+	raw_spin_lock(&versatile_lock);
+
+	/*
+	 * This is really belt and braces; we hold unintended secondary
+	 * CPUs in the holding pen until we're ready for them.  However,
+	 * since we haven't sent them a soft interrupt, they shouldn't
+	 * be there.
+	 */
+	versatile_write_cpu_release(cpu_logical_map(cpu));
+
+	/*
+	 * Send the secondary CPU a soft interrupt, thereby causing
+	 * the boot monitor to read the system wide flags register,
+	 * and branch to the address found there.
+	 */
+	arch_send_wakeup_ipi_mask(cpumask_of(cpu));
+
+	timeout = jiffies + (1 * HZ);
+	while (time_before(jiffies, timeout)) {
+		smp_rmb();
+		if (versatile_cpu_release == -1)
+			break;
+
+		udelay(10);
+	}
+
+	/*
+	 * now the secondary core is starting up let it run its
+	 * calibrations, then wait for it to finish
+	 */
+	raw_spin_unlock(&versatile_lock);
+
+	return versatile_cpu_release != -1 ? -ENOSYS : 0;
+}
diff --git a/arch/arm/plat-versatile/include/plat/platsmp.h b/arch/arm/mach-versatile/platsmp.h
index 500605f48b80..171a0ab72220 100644
--- a/arch/arm/plat-versatile/include/plat/platsmp.h
+++ b/arch/arm/mach-versatile/platsmp.h
@@ -1,7 +1,5 @@
 /* SPDX-License-Identifier: GPL-2.0-only */
 /*
- *  linux/arch/arm/plat-versatile/include/plat/platsmp.h
- *
  *  Copyright (C) 2011 ARM Ltd.
  *  All Rights Reserved
  */
diff --git a/arch/arm/mach-realview/realview-dt.c b/arch/arm/mach-versatile/realview.c
index feab66080ba2..feab66080ba2 100644
--- a/arch/arm/mach-realview/realview-dt.c
+++ b/arch/arm/mach-versatile/realview.c
diff --git a/arch/arm/mach-vexpress/spc.c b/arch/arm/mach-versatile/spc.c
index 1da11bdb1dfb..5e44170e1a9a 100644
--- a/arch/arm/mach-vexpress/spc.c
+++ b/arch/arm/mach-versatile/spc.c
@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Versatile Express Serial Power Controller (SPC) support
  *
@@ -6,15 +7,6 @@
  * Authors: Sudeep KarkadaNagesha <sudeep.karkadanagesha@arm.com>
  *          Achin Gupta           <achin.gupta@arm.com>
  *          Lorenzo Pieralisi     <lorenzo.pieralisi@arm.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- * This program is distributed "as is" WITHOUT ANY WARRANTY of any
- * kind, whether express or implied; without even the implied warranty
- * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
  */
 
 #include <linux/clk-provider.h>
@@ -122,13 +114,13 @@ static inline bool cluster_is_a15(u32 cluster)
 }
 
 /**
- * ve_spc_global_wakeup_irq()
+ * ve_spc_global_wakeup_irq() - sets/clears global wakeup IRQs
+ *
+ * @set: if true, global wake-up IRQs are set, if false they are cleared
  *
  * Function to set/clear global wakeup IRQs. Not protected by locking since
  * it might be used in code paths where normal cacheable locks are not
  * working. Locking must be provided by the caller to ensure atomicity.
- *
- * @set: if true, global wake-up IRQs are set, if false they are cleared
  */
 void ve_spc_global_wakeup_irq(bool set)
 {
@@ -145,15 +137,15 @@ void ve_spc_global_wakeup_irq(bool set)
 }
 
 /**
- * ve_spc_cpu_wakeup_irq()
- *
- * Function to set/clear per-CPU wake-up IRQs. Not protected by locking since
- * it might be used in code paths where normal cacheable locks are not
- * working. Locking must be provided by the caller to ensure atomicity.
+ * ve_spc_cpu_wakeup_irq() - sets/clears per-CPU wake-up IRQs
  *
  * @cluster: mpidr[15:8] bitfield describing cluster affinity level
  * @cpu: mpidr[7:0] bitfield describing cpu affinity level
  * @set: if true, wake-up IRQs are set, if false they are cleared
+ *
+ * Function to set/clear per-CPU wake-up IRQs. Not protected by locking since
+ * it might be used in code paths where normal cacheable locks are not
+ * working. Locking must be provided by the caller to ensure atomicity.
  */
 void ve_spc_cpu_wakeup_irq(u32 cluster, u32 cpu, bool set)
 {
@@ -200,14 +192,14 @@ void ve_spc_set_resume_addr(u32 cluster, u32 cpu, u32 addr)
 }
 
 /**
- * ve_spc_powerdown()
+ * ve_spc_powerdown() - enables/disables cluster powerdown
+ *
+ * @cluster: mpidr[15:8] bitfield describing cluster affinity level
+ * @enable: if true enables powerdown, if false disables it
  *
  * Function to enable/disable cluster powerdown. Not protected by locking
  * since it might be used in code paths where normal cacheable locks are not
  * working. Locking must be provided by the caller to ensure atomicity.
- *
- * @cluster: mpidr[15:8] bitfield describing cluster affinity level
- * @enable: if true enables powerdown, if false disables it
  */
 void ve_spc_powerdown(u32 cluster, bool enable)
 {
@@ -228,7 +220,7 @@ static u32 standbywfi_cpu_mask(u32 cpu, u32 cluster)
 }
 
 /**
- * ve_spc_cpu_in_wfi(u32 cpu, u32 cluster)
+ * ve_spc_cpu_in_wfi() - Checks if the specified CPU is in WFI or not
  *
  * @cpu: mpidr[7:0] bitfield describing CPU affinity level within cluster
  * @cluster: mpidr[15:8] bitfield describing cluster affinity level
@@ -580,7 +572,7 @@ static int __init ve_spc_clk_init(void)
 		}
 
 		cluster = topology_physical_package_id(cpu_dev->id);
-		if (init_opp_table[cluster])
+		if (cluster < 0 || init_opp_table[cluster])
 			continue;
 
 		if (ve_init_opp_table(cpu_dev))
diff --git a/arch/arm/mach-vexpress/spc.h b/arch/arm/mach-versatile/spc.h
index 288569fdfcb9..288569fdfcb9 100644
--- a/arch/arm/mach-vexpress/spc.h
+++ b/arch/arm/mach-versatile/spc.h
diff --git a/arch/arm/mach-vexpress/tc2_pm.c b/arch/arm/mach-versatile/tc2_pm.c
index e96c42ae3602..0fe78da0c109 100644
--- a/arch/arm/mach-vexpress/tc2_pm.c
+++ b/arch/arm/mach-versatile/tc2_pm.c
@@ -1,7 +1,5 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
- * arch/arm/mach-vexpress/tc2_pm.c - TC2 power management support
- *
  * Created by:	Nicolas Pitre, October 2012
  * Copyright:	(C) 2012-2013  Linaro Limited
  *
diff --git a/arch/arm/mach-vexpress/v2m-mps2.c b/arch/arm/mach-versatile/v2m-mps2.c
index 5b50d8e95cd7..5b50d8e95cd7 100644
--- a/arch/arm/mach-vexpress/v2m-mps2.c
+++ b/arch/arm/mach-versatile/v2m-mps2.c
diff --git a/arch/arm/mach-vexpress/v2m.c b/arch/arm/mach-versatile/v2m.c
index ffe7c7a85ae9..79afdf2a90b6 100644
--- a/arch/arm/mach-vexpress/v2m.c
+++ b/arch/arm/mach-versatile/v2m.c
@@ -3,7 +3,7 @@
 #include <linux/of_address.h>
 #include <asm/mach/arch.h>
 
-#include "core.h"
+#include "vexpress.h"
 
 #define SYS_FLAGSSET		0x030
 #define SYS_FLAGSCLR		0x034
diff --git a/arch/arm/mach-versatile/versatile_dt.c b/arch/arm/mach-versatile/versatile.c
index 02ba68abe533..02ba68abe533 100644
--- a/arch/arm/mach-versatile/versatile_dt.c
+++ b/arch/arm/mach-versatile/versatile.c
diff --git a/arch/arm/mach-vexpress/core.h b/arch/arm/mach-versatile/vexpress.h
index bda78675c55d..bda78675c55d 100644
--- a/arch/arm/mach-vexpress/core.h
+++ b/arch/arm/mach-versatile/vexpress.h
diff --git a/arch/arm/mach-vexpress/Kconfig b/arch/arm/mach-vexpress/Kconfig
deleted file mode 100644
index 2e6aff5a0f17..000000000000
--- a/arch/arm/mach-vexpress/Kconfig
+++ /dev/null
@@ -1,81 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0
-menuconfig ARCH_VEXPRESS
-	bool "ARM Ltd. Versatile Express family"
-	depends on ARCH_MULTI_V7
-	select ARCH_SUPPORTS_BIG_ENDIAN
-	select ARM_AMBA
-	select ARM_GIC
-	select ARM_GLOBAL_TIMER
-	select ARM_TIMER_SP804
-	select GPIOLIB
-	select HAVE_ARM_SCU if SMP
-	select HAVE_ARM_TWD if SMP
-	select HAVE_PATA_PLATFORM
-	select CLK_ICST
-	select NO_IOPORT_MAP
-	select PLAT_VERSATILE
-	select POWER_RESET
-	select POWER_RESET_VEXPRESS
-	select POWER_SUPPLY
-	select REGULATOR if MMC_ARMMMCI
-	select REGULATOR_FIXED_VOLTAGE if REGULATOR
-	select VEXPRESS_CONFIG
-	help
-	  This option enables support for systems using Cortex processor based
-	  ARM core and logic (FPGA) tiles on the Versatile Express motherboard,
-	  for example:
-
-	  - CoreTile Express A5x2 (V2P-CA5s)
-	  - CoreTile Express A9x4 (V2P-CA9)
-	  - CoreTile Express A15x2 (V2P-CA15)
-	  - LogicTile Express 13MG (V2F-2XV6) with A5, A7, A9 or A15 SMMs
-	    (Soft Macrocell Models)
-	  - Versatile Express RTSMs (Models)
-
-	  You must boot using a Flattened Device Tree in order to use these
-	  platforms. The traditional (ATAGs) boot method is not usable on
-	  these boards with this option.
-
-if ARCH_VEXPRESS
-
-config ARCH_VEXPRESS_CORTEX_A5_A9_ERRATA
-	bool "Enable A5 and A9 only errata work-arounds"
-	default y
-	select ARM_ERRATA_643719 if SMP
-	select ARM_ERRATA_720789
-	select PL310_ERRATA_753970 if CACHE_L2X0
-	help
-	  Provides common dependencies for Versatile Express platforms
-	  based on Cortex-A5 and Cortex-A9 processors. In order to
-	  build a working kernel, you must also enable relevant core
-	  tile support or Flattened Device Tree based support options.
-
-config ARCH_VEXPRESS_DCSCB
-	bool "Dual Cluster System Control Block (DCSCB) support"
-	depends on MCPM
-	select ARM_CCI400_PORT_CTRL
-	help
-	  Support for the Dual Cluster System Configuration Block (DCSCB).
-	  This is needed to provide CPU and cluster power management
-	  on RTSM implementing big.LITTLE.
-
-config ARCH_VEXPRESS_SPC
-	bool "Versatile Express Serial Power Controller (SPC)"
-	select PM_OPP
-	help
-	  The TC2 (A15x2 A7x3) versatile express core tile integrates a logic
-	  block called Serial Power Controller (SPC) that provides the interface
-	  between the dual cluster test-chip and the M3 microcontroller that
-	  carries out power management.
-
-config ARCH_VEXPRESS_TC2_PM
-	bool "Versatile Express TC2 power management"
-	depends on MCPM
-	select ARM_CCI400_PORT_CTRL
-	select ARCH_VEXPRESS_SPC
-	select ARM_CPU_SUSPEND
-	help
-	  Support for CPU and cluster power management on Versatile Express
-	  with a TC2 (A15x2 A7x3) big.LITTLE core tile.
-
-endif
diff --git a/arch/arm/mach-vexpress/Makefile b/arch/arm/mach-vexpress/Makefile
deleted file mode 100644
index 3651a1ed0f2b..000000000000
--- a/arch/arm/mach-vexpress/Makefile
+++ /dev/null
@@ -1,19 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0
-#
-# Makefile for the linux kernel.
-#
-ccflags-$(CONFIG_ARCH_MULTIPLATFORM) := \
-	-I$(srctree)/arch/arm/plat-versatile/include
-
-obj-$(CONFIG_ARCH_VEXPRESS)		:= v2m.o
-obj-$(CONFIG_ARCH_VEXPRESS_DCSCB)	+= dcscb.o	dcscb_setup.o
-CFLAGS_dcscb.o				+= -march=armv7-a
-CFLAGS_REMOVE_dcscb.o			= -pg
-obj-$(CONFIG_ARCH_VEXPRESS_SPC)		+= spc.o
-CFLAGS_REMOVE_spc.o			= -pg
-obj-$(CONFIG_ARCH_VEXPRESS_TC2_PM)	+= tc2_pm.o
-CFLAGS_tc2_pm.o				+= -march=armv7-a
-CFLAGS_REMOVE_tc2_pm.o			= -pg
-obj-$(CONFIG_SMP)			+= platsmp.o
-
-obj-$(CONFIG_ARCH_MPS2)			+= v2m-mps2.o
diff --git a/arch/arm/mach-vexpress/Makefile.boot b/arch/arm/mach-vexpress/Makefile.boot
deleted file mode 100644
index cec195d4fcba..000000000000
--- a/arch/arm/mach-vexpress/Makefile.boot
+++ /dev/null
@@ -1,4 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0-only
-# Empty file waiting for deletion once Makefile.boot isn't needed any more.
-# Patch waits for application at
-# http://www.arm.linux.org.uk/developer/patches/viewpatch.php?id=7889/1 .
diff --git a/arch/arm/mach-vexpress/platsmp.c b/arch/arm/mach-vexpress/platsmp.c
deleted file mode 100644
index 99c93124aa68..000000000000
--- a/arch/arm/mach-vexpress/platsmp.c
+++ /dev/null
@@ -1,96 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- *  linux/arch/arm/mach-vexpress/platsmp.c
- *
- *  Copyright (C) 2002 ARM Ltd.
- *  All Rights Reserved
- */
-#include <linux/init.h>
-#include <linux/errno.h>
-#include <linux/smp.h>
-#include <linux/io.h>
-#include <linux/of_address.h>
-#include <linux/vexpress.h>
-
-#include <asm/mcpm.h>
-#include <asm/smp_scu.h>
-#include <asm/mach/map.h>
-
-#include <plat/platsmp.h>
-
-#include "core.h"
-
-bool __init vexpress_smp_init_ops(void)
-{
-#ifdef CONFIG_MCPM
-	int cpu;
-	struct device_node *cpu_node, *cci_node;
-
-	/*
-	 * The best way to detect a multi-cluster configuration
-	 * is to detect if the kernel can take over CCI ports
-	 * control. Loop over possible CPUs and check if CCI
-	 * port control is available.
-	 * Override the default vexpress_smp_ops if so.
-	 */
-	for_each_possible_cpu(cpu) {
-		bool available;
-
-		cpu_node = of_get_cpu_node(cpu, NULL);
-		if (WARN(!cpu_node, "Missing cpu device node!"))
-			return false;
-
-		cci_node = of_parse_phandle(cpu_node, "cci-control-port", 0);
-		available = cci_node && of_device_is_available(cci_node);
-		of_node_put(cci_node);
-		of_node_put(cpu_node);
-
-		if (!available)
-			return false;
-	}
-
-	mcpm_smp_set_ops();
-	return true;
-#else
-	return false;
-#endif
-}
-
-static const struct of_device_id vexpress_smp_dt_scu_match[] __initconst = {
-	{ .compatible = "arm,cortex-a5-scu", },
-	{ .compatible = "arm,cortex-a9-scu", },
-	{}
-};
-
-static void __init vexpress_smp_dt_prepare_cpus(unsigned int max_cpus)
-{
-	struct device_node *scu = of_find_matching_node(NULL,
-			vexpress_smp_dt_scu_match);
-
-	if (scu)
-		scu_enable(of_iomap(scu, 0));
-
-	/*
-	 * Write the address of secondary startup into the
-	 * system-wide flags register. The boot monitor waits
-	 * until it receives a soft interrupt, and then the
-	 * secondary CPU branches to this address.
-	 */
-	vexpress_flags_set(__pa_symbol(versatile_secondary_startup));
-}
-
-#ifdef CONFIG_HOTPLUG_CPU
-static void vexpress_cpu_die(unsigned int cpu)
-{
-	versatile_immitation_cpu_die(cpu, 0x40);
-}
-#endif
-
-const struct smp_operations vexpress_smp_dt_ops __initconst = {
-	.smp_prepare_cpus	= vexpress_smp_dt_prepare_cpus,
-	.smp_secondary_init	= versatile_secondary_init,
-	.smp_boot_secondary	= versatile_boot_secondary,
-#ifdef CONFIG_HOTPLUG_CPU
-	.cpu_die		= vexpress_cpu_die,
-#endif
-};
diff --git a/arch/arm/mach-vt8500/Kconfig b/arch/arm/mach-vt8500/Kconfig
index d01cdd9ad9c7..1aad54ea3c3d 100644
--- a/arch/arm/mach-vt8500/Kconfig
+++ b/arch/arm/mach-vt8500/Kconfig
@@ -10,6 +10,7 @@ config ARCH_VT8500
 config ARCH_WM8505
 	bool "VIA/Wondermedia 85xx and WM8650"
  	depends on ARCH_MULTI_V5
+	depends on CPU_LITTLE_ENDIAN
  	select ARCH_VT8500
  	select CPU_ARM926T
 
diff --git a/arch/arm/mach-vt8500/Makefile.boot b/arch/arm/mach-vt8500/Makefile.boot
deleted file mode 100644
index 883985f4b6c1..000000000000
--- a/arch/arm/mach-vt8500/Makefile.boot
+++ /dev/null
@@ -1,4 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0-only
-   zreladdr-y	+= 0x00008000
-params_phys-y	:= 0x00000100
-initrd_phys-y	:= 0x01000000
diff --git a/arch/arm/mach-zynq/Kconfig b/arch/arm/mach-zynq/Kconfig
index a56748d671c4..05be5aa9b402 100644
--- a/arch/arm/mach-zynq/Kconfig
+++ b/arch/arm/mach-zynq/Kconfig
@@ -3,7 +3,6 @@ config ARCH_ZYNQ
 	bool "Xilinx Zynq ARM Cortex A9 Platform"
 	depends on ARCH_MULTI_V7
 	select ARCH_HAS_RESET_CONTROLLER
-	select ARCH_SUPPORTS_BIG_ENDIAN
 	select ARM_AMBA
 	select ARM_GIC
 	select ARM_GLOBAL_TIMER
diff --git a/arch/arm/mach-zynq/common.c b/arch/arm/mach-zynq/common.c
index e1ca6a5732d2..15e8a321a713 100644
--- a/arch/arm/mach-zynq/common.c
+++ b/arch/arm/mach-zynq/common.c
@@ -77,6 +77,7 @@ static int __init zynq_get_revision(void)
 	}
 
 	zynq_devcfg_base = of_iomap(np, 0);
+	of_node_put(np);
 	if (!zynq_devcfg_base) {
 		pr_err("%s: Unable to map I/O memory\n", __func__);
 		return -1;
diff --git a/arch/arm/mm/Kconfig b/arch/arm/mm/Kconfig
index 58afba346729..fc439c2c16f8 100644
--- a/arch/arm/mm/Kconfig
+++ b/arch/arm/mm/Kconfig
@@ -386,6 +386,7 @@ config CPU_V6
 	select CPU_PABRT_V6
 	select CPU_THUMB_CAPABLE
 	select CPU_TLB_V6 if MMU
+	select SMP_ON_UP if SMP
 
 # ARMv6k
 config CPU_V6K
@@ -630,7 +631,11 @@ config CPU_USE_DOMAINS
 	bool
 	help
 	  This option enables or disables the use of domain switching
-	  via the set_fs() function.
+	  using the DACR (domain access control register) to protect memory
+	  domains from each other. In Linux we use three domains: kernel, user
+	  and IO. The domains are used to protect userspace from kernelspace
+	  and to handle IO-space as a special type of memory by assigning
+	  manager or client roles to running code (such as a process).
 
 config CPU_V7M_NUM_IRQ
 	int "Number of external interrupts connected to the NVIC"
@@ -737,15 +742,29 @@ config SWP_EMULATE
 
 	  If unsure, say Y.
 
+choice
+	prompt "CPU Endianess"
+	default CPU_LITTLE_ENDIAN
+
+config CPU_LITTLE_ENDIAN
+	bool "Built little-endian kernel"
+	help
+	  Say Y if you plan on running a kernel in little-endian mode.
+	  This is the default and is used in practically all modern user
+	  space builds.
+
 config CPU_BIG_ENDIAN
 	bool "Build big-endian kernel"
-	depends on ARCH_SUPPORTS_BIG_ENDIAN
 	depends on !LD_IS_LLD
 	help
 	  Say Y if you plan on running a kernel in big-endian mode.
-	  Note that your board must be properly built and your board
-	  port must properly enable any big-endian related features
-	  of your chipset/board/processor.
+	  This works on many machines using ARMv6 or newer processors
+	  but requires big-endian user space.
+
+	  The only ARMv5 platform with big-endian support is
+	  Intel IXP4xx.
+
+endchoice
 
 config CPU_ENDIAN_BE8
 	bool
@@ -830,6 +849,7 @@ config CPU_BPREDICT_DISABLE
 
 config CPU_SPECTRE
 	bool
+	select GENERIC_CPU_VULNERABILITIES
 
 config HARDEN_BRANCH_PREDICTOR
 	bool "Harden the branch predictor against aliasing attacks" if EXPERT
@@ -850,6 +870,16 @@ config HARDEN_BRANCH_PREDICTOR
 
 	   If unsure, say Y.
 
+config HARDEN_BRANCH_HISTORY
+	bool "Harden Spectre style attacks against branch history" if EXPERT
+	depends on CPU_SPECTRE
+	default y
+	help
+	  Speculation attacks against some high-performance processors can
+	  make use of branch history to influence future speculation. When
+	  taking an exception, a sequence of branches overwrites the branch
+	  history, or branch history is invalidated.
+
 config TLS_REG_EMUL
 	bool
 	select NEED_KUSER_HELPERS
@@ -1110,12 +1140,6 @@ config ARM_DMA_MEM_BUFFERABLE
 config ARM_HEAVY_MB
 	bool
 
-config ARCH_SUPPORTS_BIG_ENDIAN
-	bool
-	help
-	  This option specifies the architecture can support big endian
-	  operation.
-
 config DEBUG_ALIGN_RODATA
 	bool "Make rodata strictly non-executable"
 	depends on STRICT_KERNEL_RWX
diff --git a/arch/arm/mm/alignment.c b/arch/arm/mm/alignment.c
index ea81e89e7740..f8dd0b3cc8e0 100644
--- a/arch/arm/mm/alignment.c
+++ b/arch/arm/mm/alignment.c
@@ -935,6 +935,9 @@ do_alignment(unsigned long addr, unsigned int fsr, struct pt_regs *regs)
 	if (type == TYPE_LDST)
 		do_alignment_finish_ldst(addr, instr, regs, offset);
 
+	if (thumb_mode(regs))
+		regs->ARM_cpsr = it_advance(regs->ARM_cpsr);
+
 	return 0;
 
  bad_or_fault:
@@ -990,7 +993,7 @@ do_alignment(unsigned long addr, unsigned int fsr, struct pt_regs *regs)
 		 * there is no work pending for this thread.
 		 */
 		raw_local_irq_disable();
-		if (!(current_thread_info()->flags & _TIF_WORK_MASK))
+		if (!(read_thread_flags() & _TIF_WORK_MASK))
 			set_cr(cr_no_alignment);
 	}
 
@@ -1005,7 +1008,7 @@ static int __init noalign_setup(char *__unused)
 __setup("noalign", noalign_setup);
 
 /*
- * This needs to be done after sysctl_init, otherwise sys/ will be
+ * This needs to be done after sysctl_init_bases(), otherwise sys/ will be
  * overwritten.  Actually, this shouldn't be in sys/ at all since
  * it isn't a sysctl, and it doesn't contain sysctl information.
  * We now locate it in /proc/cpu/alignment instead.
diff --git a/arch/arm/mm/cache-b15-rac.c b/arch/arm/mm/cache-b15-rac.c
index bdc07030997b..9c1172f26885 100644
--- a/arch/arm/mm/cache-b15-rac.c
+++ b/arch/arm/mm/cache-b15-rac.c
@@ -74,7 +74,7 @@ static inline void __b15_rac_flush(void)
 	__raw_writel(FLUSH_RAC, b15_rac_base + rac_flush_offset);
 	do {
 		/* This dmb() is required to force the Bus Interface Unit
-		 * to clean oustanding writes, and forces an idle cycle
+		 * to clean outstanding writes, and forces an idle cycle
 		 * to be inserted.
 		 */
 		dmb();
diff --git a/arch/arm/mm/cache-feroceon-l2.c b/arch/arm/mm/cache-feroceon-l2.c
index 5c1b7a7b9af6..25dbd84a1aaf 100644
--- a/arch/arm/mm/cache-feroceon-l2.c
+++ b/arch/arm/mm/cache-feroceon-l2.c
@@ -1,12 +1,9 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/mm/cache-feroceon-l2.c - Feroceon L2 cache controller support
  *
  * Copyright (C) 2008 Marvell Semiconductor
  *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- *
  * References:
  * - Unified Layer 2 Cache for Feroceon CPU Cores,
  *   Document ID MV-S104858-00, Rev. A, October 23 2007.
diff --git a/arch/arm/mm/cache-tauros2.c b/arch/arm/mm/cache-tauros2.c
index 88255bea65e4..b1e1aba602f7 100644
--- a/arch/arm/mm/cache-tauros2.c
+++ b/arch/arm/mm/cache-tauros2.c
@@ -1,12 +1,9 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * arch/arm/mm/cache-tauros2.c - Tauros2 L2 cache controller support
  *
  * Copyright (C) 2008 Marvell Semiconductor
  *
- * This file is licensed under the terms of the GNU General Public
- * License version 2.  This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- *
  * References:
  * - PJ1 CPU Core Datasheet,
  *   Document ID MV-S104837-01, Rev 0.7, January 24 2008.
diff --git a/arch/arm/mm/cache-v7.S b/arch/arm/mm/cache-v7.S
index 830bbfb26ca5..7c9499b728c4 100644
--- a/arch/arm/mm/cache-v7.S
+++ b/arch/arm/mm/cache-v7.S
@@ -90,7 +90,7 @@ ENDPROC(v7_flush_icache_all)
  *
  *     Flush the D-cache up to the Level of Unification Inner Shareable
  *
- *     Corrupted registers: r0-r7, r9-r11 (r6 only in Thumb mode)
+ *     Corrupted registers: r0-r6, r9-r10
  */
 
 ENTRY(v7_flush_dcache_louis)
@@ -117,7 +117,7 @@ ENDPROC(v7_flush_dcache_louis)
  *
  *	Flush the whole D-cache.
  *
- *	Corrupted registers: r0-r7, r9-r11 (r6 only in Thumb mode)
+ *	Corrupted registers: r0-r6, r9-r10
  *
  *	- mm    - mm_struct describing address space
  */
@@ -149,22 +149,22 @@ flush_levels:
 	movw	r4, #0x3ff
 	ands	r4, r4, r1, lsr #3		@ find maximum number on the way size
 	clz	r5, r4				@ find bit position of way size increment
-	movw	r7, #0x7fff
-	ands	r7, r7, r1, lsr #13		@ extract max number of the index size
+	movw	r6, #0x7fff
+	and	r1, r6, r1, lsr #13		@ extract max number of the index size
+	mov	r6, #1
+	movne	r4, r4, lsl r5			@ # of ways shifted into bits [31:...]
+	movne	r6, r6, lsl r5			@ 1 shifted left by same amount
 loop1:
-	mov	r9, r7				@ create working copy of max index
+	mov	r9, r1				@ create working copy of max index
 loop2:
- ARM(	orr	r11, r10, r4, lsl r5	)	@ factor way and cache number into r11
- THUMB(	lsl	r6, r4, r5		)
- THUMB(	orr	r11, r10, r6		)	@ factor way and cache number into r11
- ARM(	orr	r11, r11, r9, lsl r2	)	@ factor index number into r11
- THUMB(	lsl	r6, r9, r2		)
- THUMB(	orr	r11, r11, r6		)	@ factor index number into r11
-	mcr	p15, 0, r11, c7, c14, 2		@ clean & invalidate by set/way
+	mov	r5, r9, lsl r2			@ factor set number into r5
+	orr	r5, r5, r4			@ factor way number into r5
+	orr	r5, r5, r10			@ factor cache level into r5
+	mcr	p15, 0, r5, c7, c14, 2		@ clean & invalidate by set/way
 	subs	r9, r9, #1			@ decrement the index
 	bge	loop2
-	subs	r4, r4, #1			@ decrement the way
-	bge	loop1
+	subs	r4, r4, r6			@ decrement the way
+	bcs	loop1
 skip:
 	add	r10, r10, #2			@ increment cache number
 	cmp	r3, r10
@@ -192,14 +192,12 @@ ENDPROC(v7_flush_dcache_all)
  *
  */
 ENTRY(v7_flush_kern_cache_all)
- ARM(	stmfd	sp!, {r4-r5, r7, r9-r11, lr}	)
- THUMB(	stmfd	sp!, {r4-r7, r9-r11, lr}	)
+	stmfd	sp!, {r4-r6, r9-r10, lr}
 	bl	v7_flush_dcache_all
 	mov	r0, #0
 	ALT_SMP(mcr	p15, 0, r0, c7, c1, 0)	@ invalidate I-cache inner shareable
 	ALT_UP(mcr	p15, 0, r0, c7, c5, 0)	@ I+BTB cache invalidate
- ARM(	ldmfd	sp!, {r4-r5, r7, r9-r11, lr}	)
- THUMB(	ldmfd	sp!, {r4-r7, r9-r11, lr}	)
+	ldmfd	sp!, {r4-r6, r9-r10, lr}
 	ret	lr
 ENDPROC(v7_flush_kern_cache_all)
 
@@ -210,14 +208,12 @@ ENDPROC(v7_flush_kern_cache_all)
  *     Invalidate the I-cache to the point of unification.
  */
 ENTRY(v7_flush_kern_cache_louis)
- ARM(	stmfd	sp!, {r4-r5, r7, r9-r11, lr}	)
- THUMB(	stmfd	sp!, {r4-r7, r9-r11, lr}	)
+	stmfd	sp!, {r4-r6, r9-r10, lr}
 	bl	v7_flush_dcache_louis
 	mov	r0, #0
 	ALT_SMP(mcr	p15, 0, r0, c7, c1, 0)	@ invalidate I-cache inner shareable
 	ALT_UP(mcr	p15, 0, r0, c7, c5, 0)	@ I+BTB cache invalidate
- ARM(	ldmfd	sp!, {r4-r5, r7, r9-r11, lr}	)
- THUMB(	ldmfd	sp!, {r4-r7, r9-r11, lr}	)
+	ldmfd	sp!, {r4-r6, r9-r10, lr}
 	ret	lr
 ENDPROC(v7_flush_kern_cache_louis)
 
diff --git a/arch/arm/mm/context.c b/arch/arm/mm/context.c
index 48091870db89..4204ffa2d104 100644
--- a/arch/arm/mm/context.c
+++ b/arch/arm/mm/context.c
@@ -240,8 +240,7 @@ void check_and_switch_context(struct mm_struct *mm, struct task_struct *tsk)
 	unsigned int cpu = smp_processor_id();
 	u64 asid;
 
-	if (unlikely(mm->context.vmalloc_seq != init_mm.context.vmalloc_seq))
-		__check_vmalloc_seq(mm);
+	check_vmalloc_seq(mm);
 
 	/*
 	 * We cannot update the pgd and the ASID atomicly with classic
diff --git a/arch/arm/mm/copypage-xsc3.c b/arch/arm/mm/copypage-xsc3.c
index 6f0909dda2f9..c86e79677ff9 100644
--- a/arch/arm/mm/copypage-xsc3.c
+++ b/arch/arm/mm/copypage-xsc3.c
@@ -29,6 +29,7 @@ static void xsc3_mc_copy_user_page(void *kto, const void *kfrom)
 	int tmp;
 
 	asm volatile ("\
+.arch xscale					\n\
 	pld	[%1, #0]			\n\
 	pld	[%1, #32]			\n\
 1:	pld	[%1, #64]			\n\
@@ -80,6 +81,7 @@ void xsc3_mc_clear_user_highpage(struct page *page, unsigned long vaddr)
 {
 	void *ptr, *kaddr = kmap_atomic(page);
 	asm volatile ("\
+.arch xscale					\n\
 	mov	r1, %2				\n\
 	mov	r2, #0				\n\
 	mov	r3, #0				\n\
diff --git a/arch/arm/mm/dma-mapping.c b/arch/arm/mm/dma-mapping.c
index 4b61541853ea..d7909091cf97 100644
--- a/arch/arm/mm/dma-mapping.c
+++ b/arch/arm/mm/dma-mapping.c
@@ -33,7 +33,7 @@
 #include <asm/dma-iommu.h>
 #include <asm/mach/map.h>
 #include <asm/system_info.h>
-#include <xen/swiotlb-xen.h>
+#include <asm/xen/xen-ops.h>
 
 #include "dma.h"
 #include "mm.h"
@@ -103,139 +103,6 @@ static struct arm_dma_buffer *arm_dma_buffer_find(void *virt)
  * before transfers and delay cache invalidation until transfer completion.
  *
  */
-static void __dma_page_cpu_to_dev(struct page *, unsigned long,
-		size_t, enum dma_data_direction);
-static void __dma_page_dev_to_cpu(struct page *, unsigned long,
-		size_t, enum dma_data_direction);
-
-/**
- * arm_dma_map_page - map a portion of a page for streaming DMA
- * @dev: valid struct device pointer, or NULL for ISA and EISA-like devices
- * @page: page that buffer resides in
- * @offset: offset into page for start of buffer
- * @size: size of buffer to map
- * @dir: DMA transfer direction
- *
- * Ensure that any data held in the cache is appropriately discarded
- * or written back.
- *
- * The device owns this memory once this call has completed.  The CPU
- * can regain ownership by calling dma_unmap_page().
- */
-static dma_addr_t arm_dma_map_page(struct device *dev, struct page *page,
-	     unsigned long offset, size_t size, enum dma_data_direction dir,
-	     unsigned long attrs)
-{
-	if ((attrs & DMA_ATTR_SKIP_CPU_SYNC) == 0)
-		__dma_page_cpu_to_dev(page, offset, size, dir);
-	return pfn_to_dma(dev, page_to_pfn(page)) + offset;
-}
-
-static dma_addr_t arm_coherent_dma_map_page(struct device *dev, struct page *page,
-	     unsigned long offset, size_t size, enum dma_data_direction dir,
-	     unsigned long attrs)
-{
-	return pfn_to_dma(dev, page_to_pfn(page)) + offset;
-}
-
-/**
- * arm_dma_unmap_page - unmap a buffer previously mapped through dma_map_page()
- * @dev: valid struct device pointer, or NULL for ISA and EISA-like devices
- * @handle: DMA address of buffer
- * @size: size of buffer (same as passed to dma_map_page)
- * @dir: DMA transfer direction (same as passed to dma_map_page)
- *
- * Unmap a page streaming mode DMA translation.  The handle and size
- * must match what was provided in the previous dma_map_page() call.
- * All other usages are undefined.
- *
- * After this call, reads by the CPU to the buffer are guaranteed to see
- * whatever the device wrote there.
- */
-static void arm_dma_unmap_page(struct device *dev, dma_addr_t handle,
-		size_t size, enum dma_data_direction dir, unsigned long attrs)
-{
-	if ((attrs & DMA_ATTR_SKIP_CPU_SYNC) == 0)
-		__dma_page_dev_to_cpu(pfn_to_page(dma_to_pfn(dev, handle)),
-				      handle & ~PAGE_MASK, size, dir);
-}
-
-static void arm_dma_sync_single_for_cpu(struct device *dev,
-		dma_addr_t handle, size_t size, enum dma_data_direction dir)
-{
-	unsigned int offset = handle & (PAGE_SIZE - 1);
-	struct page *page = pfn_to_page(dma_to_pfn(dev, handle-offset));
-	__dma_page_dev_to_cpu(page, offset, size, dir);
-}
-
-static void arm_dma_sync_single_for_device(struct device *dev,
-		dma_addr_t handle, size_t size, enum dma_data_direction dir)
-{
-	unsigned int offset = handle & (PAGE_SIZE - 1);
-	struct page *page = pfn_to_page(dma_to_pfn(dev, handle-offset));
-	__dma_page_cpu_to_dev(page, offset, size, dir);
-}
-
-/*
- * Return whether the given device DMA address mask can be supported
- * properly.  For example, if your device can only drive the low 24-bits
- * during bus mastering, then you would pass 0x00ffffff as the mask
- * to this function.
- */
-static int arm_dma_supported(struct device *dev, u64 mask)
-{
-	unsigned long max_dma_pfn = min(max_pfn - 1, arm_dma_pfn_limit);
-
-	/*
-	 * Translate the device's DMA mask to a PFN limit.  This
-	 * PFN number includes the page which we can DMA to.
-	 */
-	return dma_to_pfn(dev, mask) >= max_dma_pfn;
-}
-
-const struct dma_map_ops arm_dma_ops = {
-	.alloc			= arm_dma_alloc,
-	.free			= arm_dma_free,
-	.alloc_pages		= dma_direct_alloc_pages,
-	.free_pages		= dma_direct_free_pages,
-	.mmap			= arm_dma_mmap,
-	.get_sgtable		= arm_dma_get_sgtable,
-	.map_page		= arm_dma_map_page,
-	.unmap_page		= arm_dma_unmap_page,
-	.map_sg			= arm_dma_map_sg,
-	.unmap_sg		= arm_dma_unmap_sg,
-	.map_resource		= dma_direct_map_resource,
-	.sync_single_for_cpu	= arm_dma_sync_single_for_cpu,
-	.sync_single_for_device	= arm_dma_sync_single_for_device,
-	.sync_sg_for_cpu	= arm_dma_sync_sg_for_cpu,
-	.sync_sg_for_device	= arm_dma_sync_sg_for_device,
-	.dma_supported		= arm_dma_supported,
-	.get_required_mask	= dma_direct_get_required_mask,
-};
-EXPORT_SYMBOL(arm_dma_ops);
-
-static void *arm_coherent_dma_alloc(struct device *dev, size_t size,
-	dma_addr_t *handle, gfp_t gfp, unsigned long attrs);
-static void arm_coherent_dma_free(struct device *dev, size_t size, void *cpu_addr,
-				  dma_addr_t handle, unsigned long attrs);
-static int arm_coherent_dma_mmap(struct device *dev, struct vm_area_struct *vma,
-		 void *cpu_addr, dma_addr_t dma_addr, size_t size,
-		 unsigned long attrs);
-
-const struct dma_map_ops arm_coherent_dma_ops = {
-	.alloc			= arm_coherent_dma_alloc,
-	.free			= arm_coherent_dma_free,
-	.alloc_pages		= dma_direct_alloc_pages,
-	.free_pages		= dma_direct_free_pages,
-	.mmap			= arm_coherent_dma_mmap,
-	.get_sgtable		= arm_dma_get_sgtable,
-	.map_page		= arm_coherent_dma_map_page,
-	.map_sg			= arm_dma_map_sg,
-	.map_resource		= dma_direct_map_resource,
-	.dma_supported		= arm_dma_supported,
-	.get_required_mask	= dma_direct_get_required_mask,
-};
-EXPORT_SYMBOL(arm_coherent_dma_ops);
 
 static void __dma_clear_buffer(struct page *page, size_t size, int coherent_flag)
 {
@@ -381,6 +248,7 @@ out:
  */
 postcore_initcall(atomic_pool_init);
 
+#ifdef CONFIG_CMA_AREAS
 struct dma_contig_early_reserve {
 	phys_addr_t base;
 	unsigned long size;
@@ -435,10 +303,11 @@ void __init dma_contiguous_remap(void)
 		iotable_init(&map, 1);
 	}
 }
+#endif
 
 static int __dma_update_pte(pte_t *pte, unsigned long addr, void *data)
 {
-	struct page *page = virt_to_page(addr);
+	struct page *page = virt_to_page((void *)addr);
 	pgprot_t prot = *(pgprot_t *)data;
 
 	set_pte_ext(pte, mk_pte(page, prot), 0);
@@ -707,7 +576,7 @@ static void *__dma_alloc(struct device *dev, size_t size, dma_addr_t *handle,
 
 	*handle = DMA_MAPPING_ERROR;
 	allowblock = gfpflags_allow_blocking(gfp);
-	cma = allowblock ? dev_get_cma_area(dev) : false;
+	cma = allowblock ? dev_get_cma_area(dev) : NULL;
 
 	if (cma)
 		buf->allocator = &cma_allocator;
@@ -723,7 +592,7 @@ static void *__dma_alloc(struct device *dev, size_t size, dma_addr_t *handle,
 	if (page) {
 		unsigned long flags;
 
-		*handle = pfn_to_dma(dev, page_to_pfn(page));
+		*handle = phys_to_dma(dev, page_to_phys(page));
 		buf->virt = args.want_vaddr ? addr : page;
 
 		spin_lock_irqsave(&arm_dma_bufs_lock, flags);
@@ -737,74 +606,13 @@ static void *__dma_alloc(struct device *dev, size_t size, dma_addr_t *handle,
 }
 
 /*
- * Allocate DMA-coherent memory space and return both the kernel remapped
- * virtual and bus address for that space.
- */
-void *arm_dma_alloc(struct device *dev, size_t size, dma_addr_t *handle,
-		    gfp_t gfp, unsigned long attrs)
-{
-	pgprot_t prot = __get_dma_pgprot(attrs, PAGE_KERNEL);
-
-	return __dma_alloc(dev, size, handle, gfp, prot, false,
-			   attrs, __builtin_return_address(0));
-}
-
-static void *arm_coherent_dma_alloc(struct device *dev, size_t size,
-	dma_addr_t *handle, gfp_t gfp, unsigned long attrs)
-{
-	return __dma_alloc(dev, size, handle, gfp, PAGE_KERNEL, true,
-			   attrs, __builtin_return_address(0));
-}
-
-static int __arm_dma_mmap(struct device *dev, struct vm_area_struct *vma,
-		 void *cpu_addr, dma_addr_t dma_addr, size_t size,
-		 unsigned long attrs)
-{
-	int ret = -ENXIO;
-	unsigned long nr_vma_pages = vma_pages(vma);
-	unsigned long nr_pages = PAGE_ALIGN(size) >> PAGE_SHIFT;
-	unsigned long pfn = dma_to_pfn(dev, dma_addr);
-	unsigned long off = vma->vm_pgoff;
-
-	if (dma_mmap_from_dev_coherent(dev, vma, cpu_addr, size, &ret))
-		return ret;
-
-	if (off < nr_pages && nr_vma_pages <= (nr_pages - off)) {
-		ret = remap_pfn_range(vma, vma->vm_start,
-				      pfn + off,
-				      vma->vm_end - vma->vm_start,
-				      vma->vm_page_prot);
-	}
-
-	return ret;
-}
-
-/*
- * Create userspace mapping for the DMA-coherent memory.
- */
-static int arm_coherent_dma_mmap(struct device *dev, struct vm_area_struct *vma,
-		 void *cpu_addr, dma_addr_t dma_addr, size_t size,
-		 unsigned long attrs)
-{
-	return __arm_dma_mmap(dev, vma, cpu_addr, dma_addr, size, attrs);
-}
-
-int arm_dma_mmap(struct device *dev, struct vm_area_struct *vma,
-		 void *cpu_addr, dma_addr_t dma_addr, size_t size,
-		 unsigned long attrs)
-{
-	vma->vm_page_prot = __get_dma_pgprot(attrs, vma->vm_page_prot);
-	return __arm_dma_mmap(dev, vma, cpu_addr, dma_addr, size, attrs);
-}
-
-/*
  * Free a buffer as defined by the above mapping.
  */
 static void __arm_dma_free(struct device *dev, size_t size, void *cpu_addr,
 			   dma_addr_t handle, unsigned long attrs,
 			   bool is_coherent)
 {
-	struct page *page = pfn_to_page(dma_to_pfn(dev, handle));
+	struct page *page = phys_to_page(dma_to_phys(dev, handle));
 	struct arm_dma_buffer *buf;
 	struct arm_dma_free_args args = {
 		.dev = dev,
@@ -822,40 +630,6 @@ static void __arm_dma_free(struct device *dev, size_t size, void *cpu_addr,
 	kfree(buf);
 }
 
-void arm_dma_free(struct device *dev, size_t size, void *cpu_addr,
-		  dma_addr_t handle, unsigned long attrs)
-{
-	__arm_dma_free(dev, size, cpu_addr, handle, attrs, false);
-}
-
-static void arm_coherent_dma_free(struct device *dev, size_t size, void *cpu_addr,
-				  dma_addr_t handle, unsigned long attrs)
-{
-	__arm_dma_free(dev, size, cpu_addr, handle, attrs, true);
-}
-
-int arm_dma_get_sgtable(struct device *dev, struct sg_table *sgt,
-		 void *cpu_addr, dma_addr_t handle, size_t size,
-		 unsigned long attrs)
-{
-	unsigned long pfn = dma_to_pfn(dev, handle);
-	struct page *page;
-	int ret;
-
-	/* If the PFN is not valid, we do not have a struct page */
-	if (!pfn_valid(pfn))
-		return -ENXIO;
-
-	page = pfn_to_page(pfn);
-
-	ret = sg_alloc_table(sgt, 1, GFP_KERNEL);
-	if (unlikely(ret))
-		return ret;
-
-	sg_set_page(sgt->sgl, page, PAGE_ALIGN(size), 0);
-	return 0;
-}
-
 static void dma_cache_maint_page(struct page *page, unsigned long offset,
 	size_t size, enum dma_data_direction dir,
 	void (*op)(const void *, size_t, int))
@@ -905,8 +679,7 @@ static void dma_cache_maint_page(struct page *page, unsigned long offset,
 
 /*
  * Make an area consistent for devices.
- * Note: Drivers should NOT use this function directly, as it will break
- * platforms with CONFIG_DMABOUNCE.
+ * Note: Drivers should NOT use this function directly.
  * Use the driver DMA support - see dma-mapping.h (dma_sync_*)
  */
 static void __dma_page_cpu_to_dev(struct page *page, unsigned long off,
@@ -959,122 +732,6 @@ static void __dma_page_dev_to_cpu(struct page *page, unsigned long off,
 	}
 }
 
-/**
- * arm_dma_map_sg - map a set of SG buffers for streaming mode DMA
- * @dev: valid struct device pointer, or NULL for ISA and EISA-like devices
- * @sg: list of buffers
- * @nents: number of buffers to map
- * @dir: DMA transfer direction
- *
- * Map a set of buffers described by scatterlist in streaming mode for DMA.
- * This is the scatter-gather version of the dma_map_single interface.
- * Here the scatter gather list elements are each tagged with the
- * appropriate dma address and length.  They are obtained via
- * sg_dma_{address,length}.
- *
- * Device ownership issues as mentioned for dma_map_single are the same
- * here.
- */
-int arm_dma_map_sg(struct device *dev, struct scatterlist *sg, int nents,
-		enum dma_data_direction dir, unsigned long attrs)
-{
-	const struct dma_map_ops *ops = get_dma_ops(dev);
-	struct scatterlist *s;
-	int i, j, ret;
-
-	for_each_sg(sg, s, nents, i) {
-#ifdef CONFIG_NEED_SG_DMA_LENGTH
-		s->dma_length = s->length;
-#endif
-		s->dma_address = ops->map_page(dev, sg_page(s), s->offset,
-						s->length, dir, attrs);
-		if (dma_mapping_error(dev, s->dma_address)) {
-			ret = -EIO;
-			goto bad_mapping;
-		}
-	}
-	return nents;
-
- bad_mapping:
-	for_each_sg(sg, s, i, j)
-		ops->unmap_page(dev, sg_dma_address(s), sg_dma_len(s), dir, attrs);
-	return ret;
-}
-
-/**
- * arm_dma_unmap_sg - unmap a set of SG buffers mapped by dma_map_sg
- * @dev: valid struct device pointer, or NULL for ISA and EISA-like devices
- * @sg: list of buffers
- * @nents: number of buffers to unmap (same as was passed to dma_map_sg)
- * @dir: DMA transfer direction (same as was passed to dma_map_sg)
- *
- * Unmap a set of streaming mode DMA translations.  Again, CPU access
- * rules concerning calls here are the same as for dma_unmap_single().
- */
-void arm_dma_unmap_sg(struct device *dev, struct scatterlist *sg, int nents,
-		enum dma_data_direction dir, unsigned long attrs)
-{
-	const struct dma_map_ops *ops = get_dma_ops(dev);
-	struct scatterlist *s;
-
-	int i;
-
-	for_each_sg(sg, s, nents, i)
-		ops->unmap_page(dev, sg_dma_address(s), sg_dma_len(s), dir, attrs);
-}
-
-/**
- * arm_dma_sync_sg_for_cpu
- * @dev: valid struct device pointer, or NULL for ISA and EISA-like devices
- * @sg: list of buffers
- * @nents: number of buffers to map (returned from dma_map_sg)
- * @dir: DMA transfer direction (same as was passed to dma_map_sg)
- */
-void arm_dma_sync_sg_for_cpu(struct device *dev, struct scatterlist *sg,
-			int nents, enum dma_data_direction dir)
-{
-	const struct dma_map_ops *ops = get_dma_ops(dev);
-	struct scatterlist *s;
-	int i;
-
-	for_each_sg(sg, s, nents, i)
-		ops->sync_single_for_cpu(dev, sg_dma_address(s), s->length,
-					 dir);
-}
-
-/**
- * arm_dma_sync_sg_for_device
- * @dev: valid struct device pointer, or NULL for ISA and EISA-like devices
- * @sg: list of buffers
- * @nents: number of buffers to map (returned from dma_map_sg)
- * @dir: DMA transfer direction (same as was passed to dma_map_sg)
- */
-void arm_dma_sync_sg_for_device(struct device *dev, struct scatterlist *sg,
-			int nents, enum dma_data_direction dir)
-{
-	const struct dma_map_ops *ops = get_dma_ops(dev);
-	struct scatterlist *s;
-	int i;
-
-	for_each_sg(sg, s, nents, i)
-		ops->sync_single_for_device(dev, sg_dma_address(s), s->length,
-					    dir);
-}
-
-static const struct dma_map_ops *arm_get_dma_map_ops(bool coherent)
-{
-	/*
-	 * When CONFIG_ARM_LPAE is set, physical address can extend above
-	 * 32-bits, which then can't be addressed by devices that only support
-	 * 32-bit DMA.
-	 * Use the generic dma-direct / swiotlb ops code in that case, as that
-	 * handles bounce buffering for us.
-	 */
-	if (IS_ENABLED(CONFIG_ARM_LPAE))
-		return NULL;
-	return coherent ? &arm_coherent_dma_ops : &arm_dma_ops;
-}
-
 #ifdef CONFIG_ARM_DMA_USE_IOMMU
 
 static int __dma_info_to_prot(enum dma_data_direction dir, unsigned long attrs)
@@ -1421,13 +1078,13 @@ static void __iommu_free_atomic(struct device *dev, void *cpu_addr,
 		__free_from_pool(cpu_addr, size);
 }
 
-static void *__arm_iommu_alloc_attrs(struct device *dev, size_t size,
-	    dma_addr_t *handle, gfp_t gfp, unsigned long attrs,
-	    int coherent_flag)
+static void *arm_iommu_alloc_attrs(struct device *dev, size_t size,
+	    dma_addr_t *handle, gfp_t gfp, unsigned long attrs)
 {
 	pgprot_t prot = __get_dma_pgprot(attrs, PAGE_KERNEL);
 	struct page **pages;
 	void *addr = NULL;
+	int coherent_flag = dev->dma_coherent ? COHERENT : NORMAL;
 
 	*handle = DMA_MAPPING_ERROR;
 	size = PAGE_ALIGN(size);
@@ -1470,19 +1127,7 @@ err_buffer:
 	return NULL;
 }
 
-static void *arm_iommu_alloc_attrs(struct device *dev, size_t size,
-	    dma_addr_t *handle, gfp_t gfp, unsigned long attrs)
-{
-	return __arm_iommu_alloc_attrs(dev, size, handle, gfp, attrs, NORMAL);
-}
-
-static void *arm_coherent_iommu_alloc_attrs(struct device *dev, size_t size,
-		    dma_addr_t *handle, gfp_t gfp, unsigned long attrs)
-{
-	return __arm_iommu_alloc_attrs(dev, size, handle, gfp, attrs, COHERENT);
-}
-
-static int __arm_iommu_mmap_attrs(struct device *dev, struct vm_area_struct *vma,
+static int arm_iommu_mmap_attrs(struct device *dev, struct vm_area_struct *vma,
 		    void *cpu_addr, dma_addr_t dma_addr, size_t size,
 		    unsigned long attrs)
 {
@@ -1496,35 +1141,24 @@ static int __arm_iommu_mmap_attrs(struct device *dev, struct vm_area_struct *vma
 	if (vma->vm_pgoff >= nr_pages)
 		return -ENXIO;
 
+	if (!dev->dma_coherent)
+		vma->vm_page_prot = __get_dma_pgprot(attrs, vma->vm_page_prot);
+
 	err = vm_map_pages(vma, pages, nr_pages);
 	if (err)
 		pr_err("Remapping memory failed: %d\n", err);
 
 	return err;
 }
-static int arm_iommu_mmap_attrs(struct device *dev,
-		struct vm_area_struct *vma, void *cpu_addr,
-		dma_addr_t dma_addr, size_t size, unsigned long attrs)
-{
-	vma->vm_page_prot = __get_dma_pgprot(attrs, vma->vm_page_prot);
-
-	return __arm_iommu_mmap_attrs(dev, vma, cpu_addr, dma_addr, size, attrs);
-}
-
-static int arm_coherent_iommu_mmap_attrs(struct device *dev,
-		struct vm_area_struct *vma, void *cpu_addr,
-		dma_addr_t dma_addr, size_t size, unsigned long attrs)
-{
-	return __arm_iommu_mmap_attrs(dev, vma, cpu_addr, dma_addr, size, attrs);
-}
 
 /*
  * free a page as defined by the above mapping.
  * Must not be called with IRQs disabled.
  */
-static void __arm_iommu_free_attrs(struct device *dev, size_t size, void *cpu_addr,
-	dma_addr_t handle, unsigned long attrs, int coherent_flag)
+static void arm_iommu_free_attrs(struct device *dev, size_t size, void *cpu_addr,
+	dma_addr_t handle, unsigned long attrs)
 {
+	int coherent_flag = dev->dma_coherent ? COHERENT : NORMAL;
 	struct page **pages;
 	size = PAGE_ALIGN(size);
 
@@ -1546,19 +1180,6 @@ static void __arm_iommu_free_attrs(struct device *dev, size_t size, void *cpu_ad
 	__iommu_free_buffer(dev, pages, size, attrs);
 }
 
-static void arm_iommu_free_attrs(struct device *dev, size_t size,
-				 void *cpu_addr, dma_addr_t handle,
-				 unsigned long attrs)
-{
-	__arm_iommu_free_attrs(dev, size, cpu_addr, handle, attrs, NORMAL);
-}
-
-static void arm_coherent_iommu_free_attrs(struct device *dev, size_t size,
-		    void *cpu_addr, dma_addr_t handle, unsigned long attrs)
-{
-	__arm_iommu_free_attrs(dev, size, cpu_addr, handle, attrs, COHERENT);
-}
-
 static int arm_iommu_get_sgtable(struct device *dev, struct sg_table *sgt,
 				 void *cpu_addr, dma_addr_t dma_addr,
 				 size_t size, unsigned long attrs)
@@ -1578,8 +1199,7 @@ static int arm_iommu_get_sgtable(struct device *dev, struct sg_table *sgt,
  */
 static int __map_sg_chunk(struct device *dev, struct scatterlist *sg,
 			  size_t size, dma_addr_t *handle,
-			  enum dma_data_direction dir, unsigned long attrs,
-			  bool is_coherent)
+			  enum dma_data_direction dir, unsigned long attrs)
 {
 	struct dma_iommu_mapping *mapping = to_dma_iommu_mapping(dev);
 	dma_addr_t iova, iova_base;
@@ -1599,7 +1219,7 @@ static int __map_sg_chunk(struct device *dev, struct scatterlist *sg,
 		phys_addr_t phys = page_to_phys(sg_page(s));
 		unsigned int len = PAGE_ALIGN(s->offset + s->length);
 
-		if (!is_coherent && (attrs & DMA_ATTR_SKIP_CPU_SYNC) == 0)
+		if (!dev->dma_coherent && !(attrs & DMA_ATTR_SKIP_CPU_SYNC))
 			__dma_page_cpu_to_dev(sg_page(s), s->offset, s->length, dir);
 
 		prot = __dma_info_to_prot(dir, attrs);
@@ -1619,9 +1239,20 @@ fail:
 	return ret;
 }
 
-static int __iommu_map_sg(struct device *dev, struct scatterlist *sg, int nents,
-		     enum dma_data_direction dir, unsigned long attrs,
-		     bool is_coherent)
+/**
+ * arm_iommu_map_sg - map a set of SG buffers for streaming mode DMA
+ * @dev: valid struct device pointer
+ * @sg: list of buffers
+ * @nents: number of buffers to map
+ * @dir: DMA transfer direction
+ *
+ * Map a set of buffers described by scatterlist in streaming mode for DMA.
+ * The scatter gather list elements are merged together (if possible) and
+ * tagged with the appropriate dma address and length. They are obtained via
+ * sg_dma_{address,length}.
+ */
+static int arm_iommu_map_sg(struct device *dev, struct scatterlist *sg,
+		int nents, enum dma_data_direction dir, unsigned long attrs)
 {
 	struct scatterlist *s = sg, *dma = sg, *start = sg;
 	int i, count = 0, ret;
@@ -1636,8 +1267,7 @@ static int __iommu_map_sg(struct device *dev, struct scatterlist *sg, int nents,
 
 		if (s->offset || (size & ~PAGE_MASK) || size + s->length > max) {
 			ret = __map_sg_chunk(dev, start, size,
-					     &dma->dma_address, dir, attrs,
-					     is_coherent);
+					     &dma->dma_address, dir, attrs);
 			if (ret < 0)
 				goto bad_mapping;
 
@@ -1651,8 +1281,7 @@ static int __iommu_map_sg(struct device *dev, struct scatterlist *sg, int nents,
 		}
 		size += s->length;
 	}
-	ret = __map_sg_chunk(dev, start, size, &dma->dma_address, dir, attrs,
-			     is_coherent);
+	ret = __map_sg_chunk(dev, start, size, &dma->dma_address, dir, attrs);
 	if (ret < 0)
 		goto bad_mapping;
 
@@ -1670,44 +1299,19 @@ bad_mapping:
 }
 
 /**
- * arm_coherent_iommu_map_sg - map a set of SG buffers for streaming mode DMA
- * @dev: valid struct device pointer
- * @sg: list of buffers
- * @nents: number of buffers to map
- * @dir: DMA transfer direction
- *
- * Map a set of i/o coherent buffers described by scatterlist in streaming
- * mode for DMA. The scatter gather list elements are merged together (if
- * possible) and tagged with the appropriate dma address and length. They are
- * obtained via sg_dma_{address,length}.
- */
-static int arm_coherent_iommu_map_sg(struct device *dev, struct scatterlist *sg,
-		int nents, enum dma_data_direction dir, unsigned long attrs)
-{
-	return __iommu_map_sg(dev, sg, nents, dir, attrs, true);
-}
-
-/**
- * arm_iommu_map_sg - map a set of SG buffers for streaming mode DMA
+ * arm_iommu_unmap_sg - unmap a set of SG buffers mapped by dma_map_sg
  * @dev: valid struct device pointer
  * @sg: list of buffers
- * @nents: number of buffers to map
- * @dir: DMA transfer direction
+ * @nents: number of buffers to unmap (same as was passed to dma_map_sg)
+ * @dir: DMA transfer direction (same as was passed to dma_map_sg)
  *
- * Map a set of buffers described by scatterlist in streaming mode for DMA.
- * The scatter gather list elements are merged together (if possible) and
- * tagged with the appropriate dma address and length. They are obtained via
- * sg_dma_{address,length}.
+ * Unmap a set of streaming mode DMA translations.  Again, CPU access
+ * rules concerning calls here are the same as for dma_unmap_single().
  */
-static int arm_iommu_map_sg(struct device *dev, struct scatterlist *sg,
-		int nents, enum dma_data_direction dir, unsigned long attrs)
-{
-	return __iommu_map_sg(dev, sg, nents, dir, attrs, false);
-}
-
-static void __iommu_unmap_sg(struct device *dev, struct scatterlist *sg,
-		int nents, enum dma_data_direction dir,
-		unsigned long attrs, bool is_coherent)
+static void arm_iommu_unmap_sg(struct device *dev,
+			       struct scatterlist *sg, int nents,
+			       enum dma_data_direction dir,
+			       unsigned long attrs)
 {
 	struct scatterlist *s;
 	int i;
@@ -1716,48 +1320,13 @@ static void __iommu_unmap_sg(struct device *dev, struct scatterlist *sg,
 		if (sg_dma_len(s))
 			__iommu_remove_mapping(dev, sg_dma_address(s),
 					       sg_dma_len(s));
-		if (!is_coherent && (attrs & DMA_ATTR_SKIP_CPU_SYNC) == 0)
+		if (!dev->dma_coherent && !(attrs & DMA_ATTR_SKIP_CPU_SYNC))
 			__dma_page_dev_to_cpu(sg_page(s), s->offset,
 					      s->length, dir);
 	}
 }
 
 /**
- * arm_coherent_iommu_unmap_sg - unmap a set of SG buffers mapped by dma_map_sg
- * @dev: valid struct device pointer
- * @sg: list of buffers
- * @nents: number of buffers to unmap (same as was passed to dma_map_sg)
- * @dir: DMA transfer direction (same as was passed to dma_map_sg)
- *
- * Unmap a set of streaming mode DMA translations.  Again, CPU access
- * rules concerning calls here are the same as for dma_unmap_single().
- */
-static void arm_coherent_iommu_unmap_sg(struct device *dev,
-		struct scatterlist *sg, int nents, enum dma_data_direction dir,
-		unsigned long attrs)
-{
-	__iommu_unmap_sg(dev, sg, nents, dir, attrs, true);
-}
-
-/**
- * arm_iommu_unmap_sg - unmap a set of SG buffers mapped by dma_map_sg
- * @dev: valid struct device pointer
- * @sg: list of buffers
- * @nents: number of buffers to unmap (same as was passed to dma_map_sg)
- * @dir: DMA transfer direction (same as was passed to dma_map_sg)
- *
- * Unmap a set of streaming mode DMA translations.  Again, CPU access
- * rules concerning calls here are the same as for dma_unmap_single().
- */
-static void arm_iommu_unmap_sg(struct device *dev,
-			       struct scatterlist *sg, int nents,
-			       enum dma_data_direction dir,
-			       unsigned long attrs)
-{
-	__iommu_unmap_sg(dev, sg, nents, dir, attrs, false);
-}
-
-/**
  * arm_iommu_sync_sg_for_cpu
  * @dev: valid struct device pointer
  * @sg: list of buffers
@@ -1771,6 +1340,9 @@ static void arm_iommu_sync_sg_for_cpu(struct device *dev,
 	struct scatterlist *s;
 	int i;
 
+	if (dev->dma_coherent)
+		return;
+
 	for_each_sg(sg, s, nents, i)
 		__dma_page_dev_to_cpu(sg_page(s), s->offset, s->length, dir);
 
@@ -1790,22 +1362,24 @@ static void arm_iommu_sync_sg_for_device(struct device *dev,
 	struct scatterlist *s;
 	int i;
 
+	if (dev->dma_coherent)
+		return;
+
 	for_each_sg(sg, s, nents, i)
 		__dma_page_cpu_to_dev(sg_page(s), s->offset, s->length, dir);
 }
 
-
 /**
- * arm_coherent_iommu_map_page
+ * arm_iommu_map_page
  * @dev: valid struct device pointer
  * @page: page that buffer resides in
  * @offset: offset into page for start of buffer
  * @size: size of buffer to map
  * @dir: DMA transfer direction
  *
- * Coherent IOMMU aware version of arm_dma_map_page()
+ * IOMMU aware version of arm_dma_map_page()
  */
-static dma_addr_t arm_coherent_iommu_map_page(struct device *dev, struct page *page,
+static dma_addr_t arm_iommu_map_page(struct device *dev, struct page *page,
 	     unsigned long offset, size_t size, enum dma_data_direction dir,
 	     unsigned long attrs)
 {
@@ -1813,6 +1387,9 @@ static dma_addr_t arm_coherent_iommu_map_page(struct device *dev, struct page *p
 	dma_addr_t dma_addr;
 	int ret, prot, len = PAGE_ALIGN(size + offset);
 
+	if (!dev->dma_coherent && !(attrs & DMA_ATTR_SKIP_CPU_SYNC))
+		__dma_page_cpu_to_dev(page, offset, size, dir);
+
 	dma_addr = __alloc_iova(mapping, len);
 	if (dma_addr == DMA_MAPPING_ERROR)
 		return dma_addr;
@@ -1830,50 +1407,6 @@ fail:
 }
 
 /**
- * arm_iommu_map_page
- * @dev: valid struct device pointer
- * @page: page that buffer resides in
- * @offset: offset into page for start of buffer
- * @size: size of buffer to map
- * @dir: DMA transfer direction
- *
- * IOMMU aware version of arm_dma_map_page()
- */
-static dma_addr_t arm_iommu_map_page(struct device *dev, struct page *page,
-	     unsigned long offset, size_t size, enum dma_data_direction dir,
-	     unsigned long attrs)
-{
-	if ((attrs & DMA_ATTR_SKIP_CPU_SYNC) == 0)
-		__dma_page_cpu_to_dev(page, offset, size, dir);
-
-	return arm_coherent_iommu_map_page(dev, page, offset, size, dir, attrs);
-}
-
-/**
- * arm_coherent_iommu_unmap_page
- * @dev: valid struct device pointer
- * @handle: DMA address of buffer
- * @size: size of buffer (same as passed to dma_map_page)
- * @dir: DMA transfer direction (same as passed to dma_map_page)
- *
- * Coherent IOMMU aware version of arm_dma_unmap_page()
- */
-static void arm_coherent_iommu_unmap_page(struct device *dev, dma_addr_t handle,
-		size_t size, enum dma_data_direction dir, unsigned long attrs)
-{
-	struct dma_iommu_mapping *mapping = to_dma_iommu_mapping(dev);
-	dma_addr_t iova = handle & PAGE_MASK;
-	int offset = handle & ~PAGE_MASK;
-	int len = PAGE_ALIGN(size + offset);
-
-	if (!iova)
-		return;
-
-	iommu_unmap(mapping->domain, iova, len);
-	__free_iova(mapping, iova, len);
-}
-
-/**
  * arm_iommu_unmap_page
  * @dev: valid struct device pointer
  * @handle: DMA address of buffer
@@ -1887,15 +1420,17 @@ static void arm_iommu_unmap_page(struct device *dev, dma_addr_t handle,
 {
 	struct dma_iommu_mapping *mapping = to_dma_iommu_mapping(dev);
 	dma_addr_t iova = handle & PAGE_MASK;
-	struct page *page = phys_to_page(iommu_iova_to_phys(mapping->domain, iova));
+	struct page *page;
 	int offset = handle & ~PAGE_MASK;
 	int len = PAGE_ALIGN(size + offset);
 
 	if (!iova)
 		return;
 
-	if ((attrs & DMA_ATTR_SKIP_CPU_SYNC) == 0)
+	if (!dev->dma_coherent && !(attrs & DMA_ATTR_SKIP_CPU_SYNC)) {
+		page = phys_to_page(iommu_iova_to_phys(mapping->domain, iova));
 		__dma_page_dev_to_cpu(page, offset, size, dir);
+	}
 
 	iommu_unmap(mapping->domain, iova, len);
 	__free_iova(mapping, iova, len);
@@ -1963,12 +1498,13 @@ static void arm_iommu_sync_single_for_cpu(struct device *dev,
 {
 	struct dma_iommu_mapping *mapping = to_dma_iommu_mapping(dev);
 	dma_addr_t iova = handle & PAGE_MASK;
-	struct page *page = phys_to_page(iommu_iova_to_phys(mapping->domain, iova));
+	struct page *page;
 	unsigned int offset = handle & ~PAGE_MASK;
 
-	if (!iova)
+	if (dev->dma_coherent || !iova)
 		return;
 
+	page = phys_to_page(iommu_iova_to_phys(mapping->domain, iova));
 	__dma_page_dev_to_cpu(page, offset, size, dir);
 }
 
@@ -1977,12 +1513,13 @@ static void arm_iommu_sync_single_for_device(struct device *dev,
 {
 	struct dma_iommu_mapping *mapping = to_dma_iommu_mapping(dev);
 	dma_addr_t iova = handle & PAGE_MASK;
-	struct page *page = phys_to_page(iommu_iova_to_phys(mapping->domain, iova));
+	struct page *page;
 	unsigned int offset = handle & ~PAGE_MASK;
 
-	if (!iova)
+	if (dev->dma_coherent || !iova)
 		return;
 
+	page = phys_to_page(iommu_iova_to_phys(mapping->domain, iova));
 	__dma_page_cpu_to_dev(page, offset, size, dir);
 }
 
@@ -2004,26 +1541,6 @@ static const struct dma_map_ops iommu_ops = {
 
 	.map_resource		= arm_iommu_map_resource,
 	.unmap_resource		= arm_iommu_unmap_resource,
-
-	.dma_supported		= arm_dma_supported,
-};
-
-static const struct dma_map_ops iommu_coherent_ops = {
-	.alloc		= arm_coherent_iommu_alloc_attrs,
-	.free		= arm_coherent_iommu_free_attrs,
-	.mmap		= arm_coherent_iommu_mmap_attrs,
-	.get_sgtable	= arm_iommu_get_sgtable,
-
-	.map_page	= arm_coherent_iommu_map_page,
-	.unmap_page	= arm_coherent_iommu_unmap_page,
-
-	.map_sg		= arm_coherent_iommu_map_sg,
-	.unmap_sg	= arm_coherent_iommu_unmap_sg,
-
-	.map_resource	= arm_iommu_map_resource,
-	.unmap_resource	= arm_iommu_unmap_resource,
-
-	.dma_supported		= arm_dma_supported,
 };
 
 /**
@@ -2199,40 +1716,32 @@ void arm_iommu_detach_device(struct device *dev)
 	iommu_detach_device(mapping->domain, dev);
 	kref_put(&mapping->kref, release_iommu_mapping);
 	to_dma_iommu_mapping(dev) = NULL;
-	set_dma_ops(dev, arm_get_dma_map_ops(dev->archdata.dma_coherent));
+	set_dma_ops(dev, NULL);
 
 	pr_debug("Detached IOMMU controller from %s device.\n", dev_name(dev));
 }
 EXPORT_SYMBOL_GPL(arm_iommu_detach_device);
 
-static const struct dma_map_ops *arm_get_iommu_dma_map_ops(bool coherent)
-{
-	return coherent ? &iommu_coherent_ops : &iommu_ops;
-}
-
-static bool arm_setup_iommu_dma_ops(struct device *dev, u64 dma_base, u64 size,
-				    const struct iommu_ops *iommu)
+static void arm_setup_iommu_dma_ops(struct device *dev, u64 dma_base, u64 size,
+				    const struct iommu_ops *iommu, bool coherent)
 {
 	struct dma_iommu_mapping *mapping;
 
-	if (!iommu)
-		return false;
-
 	mapping = arm_iommu_create_mapping(dev->bus, dma_base, size);
 	if (IS_ERR(mapping)) {
 		pr_warn("Failed to create %llu-byte IOMMU mapping for device %s\n",
 				size, dev_name(dev));
-		return false;
+		return;
 	}
 
 	if (__arm_iommu_attach_device(dev, mapping)) {
 		pr_warn("Failed to attached device %s to IOMMU_mapping\n",
 				dev_name(dev));
 		arm_iommu_release_mapping(mapping);
-		return false;
+		return;
 	}
 
-	return true;
+	set_dma_ops(dev, &iommu_ops);
 }
 
 static void arm_teardown_iommu_dma_ops(struct device *dev)
@@ -2248,27 +1757,26 @@ static void arm_teardown_iommu_dma_ops(struct device *dev)
 
 #else
 
-static bool arm_setup_iommu_dma_ops(struct device *dev, u64 dma_base, u64 size,
-				    const struct iommu_ops *iommu)
+static void arm_setup_iommu_dma_ops(struct device *dev, u64 dma_base, u64 size,
+				    const struct iommu_ops *iommu, bool coherent)
 {
-	return false;
 }
 
 static void arm_teardown_iommu_dma_ops(struct device *dev) { }
 
-#define arm_get_iommu_dma_map_ops arm_get_dma_map_ops
-
 #endif	/* CONFIG_ARM_DMA_USE_IOMMU */
 
 void arch_setup_dma_ops(struct device *dev, u64 dma_base, u64 size,
 			const struct iommu_ops *iommu, bool coherent)
 {
-	const struct dma_map_ops *dma_ops;
-
-	dev->archdata.dma_coherent = coherent;
-#ifdef CONFIG_SWIOTLB
-	dev->dma_coherent = coherent;
-#endif
+	/*
+	 * Due to legacy code that sets the ->dma_coherent flag from a bus
+	 * notifier we can't just assign coherent to the ->dma_coherent flag
+	 * here, but instead have to make sure we only set but never clear it
+	 * for now.
+	 */
+	if (coherent)
+		dev->dma_coherent = true;
 
 	/*
 	 * Don't override the dma_ops if they have already been set. Ideally
@@ -2278,17 +1786,10 @@ void arch_setup_dma_ops(struct device *dev, u64 dma_base, u64 size,
 	if (dev->dma_ops)
 		return;
 
-	if (arm_setup_iommu_dma_ops(dev, dma_base, size, iommu))
-		dma_ops = arm_get_iommu_dma_map_ops(coherent);
-	else
-		dma_ops = arm_get_dma_map_ops(coherent);
+	if (iommu)
+		arm_setup_iommu_dma_ops(dev, dma_base, size, iommu, coherent);
 
-	set_dma_ops(dev, dma_ops);
-
-#ifdef CONFIG_XEN
-	if (xen_initial_domain())
-		dev->dma_ops = &xen_swiotlb_dma_ops;
-#endif
+	xen_setup_dma_ops(dev);
 	dev->archdata.dma_ops_setup = true;
 }
 
@@ -2302,7 +1803,6 @@ void arch_teardown_dma_ops(struct device *dev)
 	set_dma_ops(dev, NULL);
 }
 
-#ifdef CONFIG_SWIOTLB
 void arch_sync_dma_for_device(phys_addr_t paddr, size_t size,
 		enum dma_data_direction dir)
 {
@@ -2330,4 +1830,3 @@ void arch_dma_free(struct device *dev, size_t size, void *cpu_addr,
 {
 	__arm_dma_free(dev, size, cpu_addr, dma_handle, attrs, false);
 }
-#endif /* CONFIG_SWIOTLB */
diff --git a/arch/arm/mm/dump.c b/arch/arm/mm/dump.c
index fb688003d156..059eb4cdc9c2 100644
--- a/arch/arm/mm/dump.c
+++ b/arch/arm/mm/dump.c
@@ -26,7 +26,7 @@ static struct addr_marker address_markers[] = {
 	{ MODULES_VADDR,	"Modules" },
 	{ PAGE_OFFSET,		"Kernel Mapping" },
 	{ 0,			"vmalloc() Area" },
-	{ VMALLOC_END,		"vmalloc() End" },
+	{ FDT_FIXED_BASE,	"FDT Area" },
 	{ FIXADDR_START,	"Fixmap Area" },
 	{ VECTORS_BASE,	"Vectors" },
 	{ VECTORS_BASE + PAGE_SIZE * 2, "Vectors End" },
@@ -200,6 +200,7 @@ static const struct prot_bits section_bits[] = {
 };
 
 struct pg_level {
+	const char *name;
 	const struct prot_bits *bits;
 	size_t num;
 	u64 mask;
@@ -213,9 +214,11 @@ static struct pg_level pg_level[] = {
 	}, { /* p4d */
 	}, { /* pud */
 	}, { /* pmd */
+		.name	= (CONFIG_PGTABLE_LEVELS > 2) ? "PMD" : "PGD",
 		.bits	= section_bits,
 		.num	= ARRAY_SIZE(section_bits),
 	}, { /* pte */
+		.name	= "PTE",
 		.bits	= pte_bits,
 		.num	= ARRAY_SIZE(pte_bits),
 	},
@@ -282,7 +285,8 @@ static void note_page(struct pg_state *st, unsigned long addr,
 				delta >>= 10;
 				unit++;
 			}
-			pt_dump_seq_printf(st->seq, "%9lu%c", delta, *unit);
+			pt_dump_seq_printf(st->seq, "%9lu%c %s", delta, *unit,
+					   pg_level[st->level].name);
 			if (st->current_domain)
 				pt_dump_seq_printf(st->seq, " %s",
 							st->current_domain);
@@ -346,7 +350,7 @@ static void walk_pmd(struct pg_state *st, pud_t *pud, unsigned long start)
 		addr = start + i * PMD_SIZE;
 		domain = get_domain_name(pmd);
 		if (pmd_none(*pmd) || pmd_large(*pmd) || !pmd_present(*pmd))
-			note_page(st, addr, 3, pmd_val(*pmd), domain);
+			note_page(st, addr, 4, pmd_val(*pmd), domain);
 		else
 			walk_pte(st, pmd, addr, domain);
 
diff --git a/arch/arm/mm/fault.c b/arch/arm/mm/fault.c
index bc8779d54a64..46cccd6bf705 100644
--- a/arch/arm/mm/fault.c
+++ b/arch/arm/mm/fault.c
@@ -17,6 +17,7 @@
 #include <linux/sched/debug.h>
 #include <linux/highmem.h>
 #include <linux/perf_event.h>
+#include <linux/kfence.h>
 
 #include <asm/system_misc.h>
 #include <asm/system_info.h>
@@ -99,6 +100,11 @@ void show_pte(const char *lvl, struct mm_struct *mm, unsigned long addr)
 { }
 #endif					/* CONFIG_MMU */
 
+static inline bool is_write_fault(unsigned int fsr)
+{
+	return (fsr & FSR_WRITE) && !(fsr & FSR_CM);
+}
+
 static void die_kernel_fault(const char *msg, struct mm_struct *mm,
 			     unsigned long addr, unsigned int fsr,
 			     struct pt_regs *regs)
@@ -111,7 +117,7 @@ static void die_kernel_fault(const char *msg, struct mm_struct *mm,
 	show_pte(KERN_ALERT, mm, addr);
 	die("Oops", regs, fsr);
 	bust_spinlocks(0);
-	do_exit(SIGKILL);
+	make_task_dead(SIGKILL);
 }
 
 /*
@@ -131,10 +137,14 @@ __do_kernel_fault(struct mm_struct *mm, unsigned long addr, unsigned int fsr,
 	/*
 	 * No handler, we'll have to terminate things with extreme prejudice.
 	 */
-	if (addr < PAGE_SIZE)
+	if (addr < PAGE_SIZE) {
 		msg = "NULL pointer dereference";
-	else
+	} else {
+		if (kfence_handle_page_fault(addr, is_write_fault(fsr), regs))
+			return;
+
 		msg = "paging request";
+	}
 
 	die_kernel_fault(msg, mm, addr, fsr, regs);
 }
@@ -191,8 +201,8 @@ void do_bad_area(unsigned long addr, unsigned int fsr, struct pt_regs *regs)
 }
 
 #ifdef CONFIG_MMU
-#define VM_FAULT_BADMAP		0x010000
-#define VM_FAULT_BADACCESS	0x020000
+#define VM_FAULT_BADMAP		((__force vm_fault_t)0x010000)
+#define VM_FAULT_BADACCESS	((__force vm_fault_t)0x020000)
 
 static inline bool is_permission_fault(unsigned int fsr)
 {
@@ -261,7 +271,7 @@ do_page_fault(unsigned long addr, unsigned int fsr, struct pt_regs *regs)
 	if (user_mode(regs))
 		flags |= FAULT_FLAG_USER;
 
-	if ((fsr & FSR_WRITE) && !(fsr & FSR_CM)) {
+	if (is_write_fault(fsr)) {
 		flags |= FAULT_FLAG_WRITE;
 		vm_flags = VM_WRITE;
 	}
@@ -312,7 +322,11 @@ retry:
 		return 0;
 	}
 
-	if (!(fault & VM_FAULT_ERROR) && flags & FAULT_FLAG_ALLOW_RETRY) {
+	/* The fault is fully completed (including releasing mmap lock) */
+	if (fault & VM_FAULT_COMPLETED)
+		return 0;
+
+	if (!(fault & VM_FAULT_ERROR)) {
 		if (fault & VM_FAULT_RETRY) {
 			flags |= FAULT_FLAG_TRIED;
 			goto retry;
diff --git a/arch/arm/mm/init.c b/arch/arm/mm/init.c
index 6d0cb0f7bc54..ce64bdb55a16 100644
--- a/arch/arm/mm/init.c
+++ b/arch/arm/mm/init.c
@@ -164,47 +164,6 @@ phys_addr_t __init arm_memblock_steal(phys_addr_t size, phys_addr_t align)
 	return phys;
 }
 
-static void __init arm_initrd_init(void)
-{
-#ifdef CONFIG_BLK_DEV_INITRD
-	phys_addr_t start;
-	unsigned long size;
-
-	initrd_start = initrd_end = 0;
-
-	if (!phys_initrd_size)
-		return;
-
-	/*
-	 * Round the memory region to page boundaries as per free_initrd_mem()
-	 * This allows us to detect whether the pages overlapping the initrd
-	 * are in use, but more importantly, reserves the entire set of pages
-	 * as we don't want these pages allocated for other purposes.
-	 */
-	start = round_down(phys_initrd_start, PAGE_SIZE);
-	size = phys_initrd_size + (phys_initrd_start - start);
-	size = round_up(size, PAGE_SIZE);
-
-	if (!memblock_is_region_memory(start, size)) {
-		pr_err("INITRD: 0x%08llx+0x%08lx is not a memory region - disabling initrd\n",
-		       (u64)start, size);
-		return;
-	}
-
-	if (memblock_is_region_reserved(start, size)) {
-		pr_err("INITRD: 0x%08llx+0x%08lx overlaps in-use memory region - disabling initrd\n",
-		       (u64)start, size);
-		return;
-	}
-
-	memblock_reserve(start, size);
-
-	/* Now convert initrd to virtual addresses */
-	initrd_start = __phys_to_virt(phys_initrd_start);
-	initrd_end = initrd_start + phys_initrd_size;
-#endif
-}
-
 #ifdef CONFIG_CPU_ICACHE_MISMATCH_WORKAROUND
 void check_cpu_icache_size(int cpuid)
 {
@@ -226,7 +185,7 @@ void __init arm_memblock_init(const struct machine_desc *mdesc)
 	/* Register the kernel text, kernel data and initrd with memblock. */
 	memblock_reserve(__pa(KERNEL_START), KERNEL_END - KERNEL_START);
 
-	arm_initrd_init();
+	reserve_initrd_mem();
 
 	arm_mm_memblock_reserve();
 
@@ -312,11 +271,7 @@ static void __init free_highpages(void)
 void __init mem_init(void)
 {
 #ifdef CONFIG_ARM_LPAE
-	if (swiotlb_force == SWIOTLB_FORCE ||
-	    max_pfn > arm_dma_pfn_limit)
-		swiotlb_init(1);
-	else
-		swiotlb_force = SWIOTLB_NO_FORCE;
+	swiotlb_init(max_pfn > arm_dma_pfn_limit, SWIOTLB_VERBOSE);
 #endif
 
 	set_max_mapnr(pfn_to_page(max_pfn) - mem_map);
diff --git a/arch/arm/mm/ioremap.c b/arch/arm/mm/ioremap.c
index 6e830b9418c9..2129070065c3 100644
--- a/arch/arm/mm/ioremap.c
+++ b/arch/arm/mm/ioremap.c
@@ -117,16 +117,21 @@ EXPORT_SYMBOL(ioremap_page);
 
 void __check_vmalloc_seq(struct mm_struct *mm)
 {
-	unsigned int seq;
+	int seq;
 
 	do {
-		seq = init_mm.context.vmalloc_seq;
+		seq = atomic_read(&init_mm.context.vmalloc_seq);
 		memcpy(pgd_offset(mm, VMALLOC_START),
 		       pgd_offset_k(VMALLOC_START),
 		       sizeof(pgd_t) * (pgd_index(VMALLOC_END) -
 					pgd_index(VMALLOC_START)));
-		mm->context.vmalloc_seq = seq;
-	} while (seq != init_mm.context.vmalloc_seq);
+		/*
+		 * Use a store-release so that other CPUs that observe the
+		 * counter's new value are guaranteed to see the results of the
+		 * memcpy as well.
+		 */
+		atomic_set_release(&mm->context.vmalloc_seq, seq);
+	} while (seq != atomic_read(&init_mm.context.vmalloc_seq));
 }
 
 #if !defined(CONFIG_SMP) && !defined(CONFIG_ARM_LPAE)
@@ -157,7 +162,7 @@ static void unmap_area_sections(unsigned long virt, unsigned long size)
 			 * Note: this is still racy on SMP machines.
 			 */
 			pmd_clear(pmdp);
-			init_mm.context.vmalloc_seq++;
+			atomic_inc_return_release(&init_mm.context.vmalloc_seq);
 
 			/*
 			 * Free the page table, if there was one.
@@ -174,8 +179,7 @@ static void unmap_area_sections(unsigned long virt, unsigned long size)
 	 * Ensure that the active_mm is up to date - we want to
 	 * catch any use-after-iounmap cases.
 	 */
-	if (current->active_mm->context.vmalloc_seq != init_mm.context.vmalloc_seq)
-		__check_vmalloc_seq(current->active_mm);
+	check_vmalloc_seq(current->active_mm);
 
 	flush_tlb_kernel_range(virt, end);
 }
@@ -414,7 +418,7 @@ void *arch_memremap_wb(phys_addr_t phys_addr, size_t size)
 						   __builtin_return_address(0));
 }
 
-void __iounmap(volatile void __iomem *io_addr)
+void iounmap(volatile void __iomem *io_addr)
 {
 	void *addr = (void *)(PAGE_MASK & (unsigned long)io_addr);
 	struct static_vm *svm;
@@ -442,16 +446,9 @@ void __iounmap(volatile void __iomem *io_addr)
 
 	vunmap(addr);
 }
-
-void (*arch_iounmap)(volatile void __iomem *) = __iounmap;
-
-void iounmap(volatile void __iomem *cookie)
-{
-	arch_iounmap(cookie);
-}
 EXPORT_SYMBOL(iounmap);
 
-#ifdef CONFIG_PCI
+#if defined(CONFIG_PCI) || IS_ENABLED(CONFIG_PCMCIA)
 static int pci_ioremap_mem_type = MT_DEVICE;
 
 void pci_ioremap_set_mem_type(int mem_type)
@@ -459,16 +456,20 @@ void pci_ioremap_set_mem_type(int mem_type)
 	pci_ioremap_mem_type = mem_type;
 }
 
-int pci_ioremap_io(unsigned int offset, phys_addr_t phys_addr)
+int pci_remap_iospace(const struct resource *res, phys_addr_t phys_addr)
 {
-	BUG_ON(offset + SZ_64K - 1 > IO_SPACE_LIMIT);
+	unsigned long vaddr = (unsigned long)PCI_IOBASE + res->start;
 
-	return ioremap_page_range(PCI_IO_VIRT_BASE + offset,
-				  PCI_IO_VIRT_BASE + offset + SZ_64K,
-				  phys_addr,
+	if (!(res->flags & IORESOURCE_IO))
+		return -EINVAL;
+
+	if (res->end > IO_SPACE_LIMIT)
+		return -EINVAL;
+
+	return ioremap_page_range(vaddr, vaddr + resource_size(res), phys_addr,
 				  __pgprot(get_mem_type(pci_ioremap_mem_type)->prot_pte));
 }
-EXPORT_SYMBOL_GPL(pci_ioremap_io);
+EXPORT_SYMBOL(pci_remap_iospace);
 
 void __iomem *pci_remap_cfgspace(resource_size_t res_cookie, size_t size)
 {
@@ -485,3 +486,11 @@ void __init early_ioremap_init(void)
 {
 	early_ioremap_setup();
 }
+
+bool arch_memremap_can_ram_remap(resource_size_t offset, size_t size,
+				 unsigned long flags)
+{
+	unsigned long pfn = PHYS_PFN(offset);
+
+	return memblock_is_map_memory(pfn);
+}
diff --git a/arch/arm/mm/kasan_init.c b/arch/arm/mm/kasan_init.c
index 5ad0d6c56d56..46d9f4a622cb 100644
--- a/arch/arm/mm/kasan_init.c
+++ b/arch/arm/mm/kasan_init.c
@@ -236,7 +236,11 @@ void __init kasan_init(void)
 
 	clear_pgds(KASAN_SHADOW_START, KASAN_SHADOW_END);
 
-	kasan_populate_early_shadow(kasan_mem_to_shadow((void *)VMALLOC_START),
+	if (!IS_ENABLED(CONFIG_KASAN_VMALLOC))
+		kasan_populate_early_shadow(kasan_mem_to_shadow((void *)VMALLOC_START),
+					    kasan_mem_to_shadow((void *)VMALLOC_END));
+
+	kasan_populate_early_shadow(kasan_mem_to_shadow((void *)VMALLOC_END),
 				    kasan_mem_to_shadow((void *)-1UL) + 1);
 
 	for_each_mem_range(i, &pa_start, &pa_end) {
@@ -264,12 +268,17 @@ void __init kasan_init(void)
 
 	/*
 	 * 1. The module global variables are in MODULES_VADDR ~ MODULES_END,
-	 *    so we need to map this area.
+	 *    so we need to map this area if CONFIG_KASAN_VMALLOC=n. With
+	 *    VMALLOC support KASAN will manage this region dynamically,
+	 *    refer to kasan_populate_vmalloc() and ARM's implementation of
+	 *    module_alloc().
 	 * 2. PKMAP_BASE ~ PKMAP_BASE+PMD_SIZE's shadow and MODULES_VADDR
 	 *    ~ MODULES_END's shadow is in the same PMD_SIZE, so we can't
 	 *    use kasan_populate_zero_shadow.
 	 */
-	create_mapping((void *)MODULES_VADDR, (void *)(PKMAP_BASE + PMD_SIZE));
+	if (!IS_ENABLED(CONFIG_KASAN_VMALLOC) && IS_ENABLED(CONFIG_MODULES))
+		create_mapping((void *)MODULES_VADDR, (void *)(MODULES_END));
+	create_mapping((void *)PKMAP_BASE, (void *)(PKMAP_BASE + PMD_SIZE));
 
 	/*
 	 * KAsan may reuse the contents of kasan_early_shadow_pte directly, so
diff --git a/arch/arm/mm/mm.h b/arch/arm/mm/mm.h
index 9ff683612f2a..d7ffccb7fea7 100644
--- a/arch/arm/mm/mm.h
+++ b/arch/arm/mm/mm.h
@@ -88,6 +88,10 @@ extern phys_addr_t arm_lowmem_limit;
 
 void __init bootmem_init(void);
 void arm_mm_memblock_reserve(void);
+#ifdef CONFIG_CMA_AREAS
 void dma_contiguous_remap(void);
+#else
+static inline void dma_contiguous_remap(void) { }
+#endif
 
 unsigned long __clear_cr(unsigned long mask);
diff --git a/arch/arm/mm/mmu.c b/arch/arm/mm/mmu.c
index 274e4f73fd33..463fc2a8448f 100644
--- a/arch/arm/mm/mmu.c
+++ b/arch/arm/mm/mmu.c
@@ -212,12 +212,14 @@ early_param("ecc", early_ecc);
 static int __init early_cachepolicy(char *p)
 {
 	pr_warn("cachepolicy kernel parameter not supported without cp15\n");
+	return 0;
 }
 early_param("cachepolicy", early_cachepolicy);
 
 static int __init noalign_setup(char *__unused)
 {
 	pr_warn("noalign kernel parameter not supported without cp15\n");
+	return 1;
 }
 __setup("noalign", noalign_setup);
 
@@ -294,6 +296,17 @@ static struct mem_type mem_types[] __ro_after_init = {
 		.prot_sect = PMD_TYPE_SECT | PMD_SECT_AP_WRITE,
 		.domain    = DOMAIN_KERNEL,
 	},
+	[MT_MEMORY_RO] = {
+		.prot_pte  = L_PTE_PRESENT | L_PTE_YOUNG | L_PTE_DIRTY |
+			     L_PTE_XN | L_PTE_RDONLY,
+		.prot_l1   = PMD_TYPE_TABLE,
+#ifdef CONFIG_ARM_LPAE
+		.prot_sect = PMD_TYPE_SECT | L_PMD_SECT_RDONLY | PMD_SECT_AP2,
+#else
+		.prot_sect = PMD_TYPE_SECT,
+#endif
+		.domain    = DOMAIN_KERNEL,
+	},
 	[MT_ROM] = {
 		.prot_sect = PMD_TYPE_SECT,
 		.domain    = DOMAIN_KERNEL,
@@ -403,6 +416,26 @@ void __set_fixmap(enum fixed_addresses idx, phys_addr_t phys, pgprot_t prot)
 	local_flush_tlb_kernel_range(vaddr, vaddr + PAGE_SIZE);
 }
 
+static pgprot_t protection_map[16] __ro_after_init = {
+	[VM_NONE]					= __PAGE_NONE,
+	[VM_READ]					= __PAGE_READONLY,
+	[VM_WRITE]					= __PAGE_COPY,
+	[VM_WRITE | VM_READ]				= __PAGE_COPY,
+	[VM_EXEC]					= __PAGE_READONLY_EXEC,
+	[VM_EXEC | VM_READ]				= __PAGE_READONLY_EXEC,
+	[VM_EXEC | VM_WRITE]				= __PAGE_COPY_EXEC,
+	[VM_EXEC | VM_WRITE | VM_READ]			= __PAGE_COPY_EXEC,
+	[VM_SHARED]					= __PAGE_NONE,
+	[VM_SHARED | VM_READ]				= __PAGE_READONLY,
+	[VM_SHARED | VM_WRITE]				= __PAGE_SHARED,
+	[VM_SHARED | VM_WRITE | VM_READ]		= __PAGE_SHARED,
+	[VM_SHARED | VM_EXEC]				= __PAGE_READONLY_EXEC,
+	[VM_SHARED | VM_EXEC | VM_READ]			= __PAGE_READONLY_EXEC,
+	[VM_SHARED | VM_EXEC | VM_WRITE]		= __PAGE_SHARED_EXEC,
+	[VM_SHARED | VM_EXEC | VM_WRITE | VM_READ]	= __PAGE_SHARED_EXEC
+};
+DECLARE_VM_GET_PAGE_PROT
+
 /*
  * Adjust the PMD section entries according to the CPU in use.
  */
@@ -487,6 +520,7 @@ static void __init build_mem_type_table(void)
 
 			/* Also setup NX memory mapping */
 			mem_types[MT_MEMORY_RW].prot_sect |= PMD_SECT_XN;
+			mem_types[MT_MEMORY_RO].prot_sect |= PMD_SECT_XN;
 		}
 		if (cpu_arch >= CPU_ARCH_ARMv7 && (cr & CR_TRE)) {
 			/*
@@ -566,6 +600,7 @@ static void __init build_mem_type_table(void)
 		mem_types[MT_ROM].prot_sect |= PMD_SECT_APX|PMD_SECT_AP_WRITE;
 		mem_types[MT_MINICLEAN].prot_sect |= PMD_SECT_APX|PMD_SECT_AP_WRITE;
 		mem_types[MT_CACHECLEAN].prot_sect |= PMD_SECT_APX|PMD_SECT_AP_WRITE;
+		mem_types[MT_MEMORY_RO].prot_sect |= PMD_SECT_APX|PMD_SECT_AP_WRITE;
 #endif
 
 		/*
@@ -585,6 +620,8 @@ static void __init build_mem_type_table(void)
 			mem_types[MT_MEMORY_RWX].prot_pte |= L_PTE_SHARED;
 			mem_types[MT_MEMORY_RW].prot_sect |= PMD_SECT_S;
 			mem_types[MT_MEMORY_RW].prot_pte |= L_PTE_SHARED;
+			mem_types[MT_MEMORY_RO].prot_sect |= PMD_SECT_S;
+			mem_types[MT_MEMORY_RO].prot_pte |= L_PTE_SHARED;
 			mem_types[MT_MEMORY_DMA_READY].prot_pte |= L_PTE_SHARED;
 			mem_types[MT_MEMORY_RWX_NONCACHED].prot_sect |= PMD_SECT_S;
 			mem_types[MT_MEMORY_RWX_NONCACHED].prot_pte |= L_PTE_SHARED;
@@ -645,6 +682,8 @@ static void __init build_mem_type_table(void)
 	mem_types[MT_MEMORY_RWX].prot_pte |= kern_pgprot;
 	mem_types[MT_MEMORY_RW].prot_sect |= ecc_mask | cp->pmd;
 	mem_types[MT_MEMORY_RW].prot_pte |= kern_pgprot;
+	mem_types[MT_MEMORY_RO].prot_sect |= ecc_mask | cp->pmd;
+	mem_types[MT_MEMORY_RO].prot_pte |= kern_pgprot;
 	mem_types[MT_MEMORY_DMA_READY].prot_pte |= kern_pgprot;
 	mem_types[MT_MEMORY_RWX_NONCACHED].prot_sect |= ecc_mask;
 	mem_types[MT_ROM].prot_sect |= cp->pmd;
@@ -1358,7 +1397,7 @@ static void __init devicemaps_init(const struct machine_desc *mdesc)
 		map.pfn = __phys_to_pfn(__atags_pointer & SECTION_MASK);
 		map.virtual = FDT_FIXED_BASE;
 		map.length = FDT_FIXED_SIZE;
-		map.type = MT_ROM;
+		map.type = MT_MEMORY_RO;
 		create_mapping(&map);
 	}
 
diff --git a/arch/arm/mm/nommu.c b/arch/arm/mm/nommu.c
index 2658f52903da..c42debaded95 100644
--- a/arch/arm/mm/nommu.c
+++ b/arch/arm/mm/nommu.c
@@ -230,14 +230,7 @@ void *arch_memremap_wb(phys_addr_t phys_addr, size_t size)
 	return (void *)phys_addr;
 }
 
-void __iounmap(volatile void __iomem *addr)
-{
-}
-EXPORT_SYMBOL(__iounmap);
-
-void (*arch_iounmap)(volatile void __iomem *);
-
-void iounmap(volatile void __iomem *addr)
+void iounmap(volatile void __iomem *io_addr)
 {
 }
 EXPORT_SYMBOL(iounmap);
diff --git a/arch/arm/mm/pageattr.c b/arch/arm/mm/pageattr.c
index 9790ae3a8c68..c3c34fe714b0 100644
--- a/arch/arm/mm/pageattr.c
+++ b/arch/arm/mm/pageattr.c
@@ -32,14 +32,31 @@ static bool in_range(unsigned long start, unsigned long size,
 		size <= range_end - start;
 }
 
+/*
+ * This function assumes that the range is mapped with PAGE_SIZE pages.
+ */
+static int __change_memory_common(unsigned long start, unsigned long size,
+				pgprot_t set_mask, pgprot_t clear_mask)
+{
+	struct page_change_data data;
+	int ret;
+
+	data.set_mask = set_mask;
+	data.clear_mask = clear_mask;
+
+	ret = apply_to_page_range(&init_mm, start, size, change_page_range,
+				  &data);
+
+	flush_tlb_kernel_range(start, start + size);
+	return ret;
+}
+
 static int change_memory_common(unsigned long addr, int numpages,
 				pgprot_t set_mask, pgprot_t clear_mask)
 {
 	unsigned long start = addr & PAGE_MASK;
 	unsigned long end = PAGE_ALIGN(addr) + numpages * PAGE_SIZE;
 	unsigned long size = end - start;
-	int ret;
-	struct page_change_data data;
 
 	WARN_ON_ONCE(start != addr);
 
@@ -50,14 +67,7 @@ static int change_memory_common(unsigned long addr, int numpages,
 	    !in_range(start, size, VMALLOC_START, VMALLOC_END))
 		return -EINVAL;
 
-	data.set_mask = set_mask;
-	data.clear_mask = clear_mask;
-
-	ret = apply_to_page_range(&init_mm, start, size, change_page_range,
-					&data);
-
-	flush_tlb_kernel_range(start, end);
-	return ret;
+	return __change_memory_common(start, size, set_mask, clear_mask);
 }
 
 int set_memory_ro(unsigned long addr, int numpages)
@@ -87,3 +97,15 @@ int set_memory_x(unsigned long addr, int numpages)
 					__pgprot(0),
 					__pgprot(L_PTE_XN));
 }
+
+int set_memory_valid(unsigned long addr, int numpages, int enable)
+{
+	if (enable)
+		return __change_memory_common(addr, PAGE_SIZE * numpages,
+					      __pgprot(L_PTE_VALID),
+					      __pgprot(0));
+	else
+		return __change_memory_common(addr, PAGE_SIZE * numpages,
+					      __pgprot(0),
+					      __pgprot(L_PTE_VALID));
+}
diff --git a/arch/arm/mm/proc-v7-bugs.c b/arch/arm/mm/proc-v7-bugs.c
index 114c05ab4dd9..8bc7a2d6d6c7 100644
--- a/arch/arm/mm/proc-v7-bugs.c
+++ b/arch/arm/mm/proc-v7-bugs.c
@@ -6,8 +6,35 @@
 #include <asm/cp15.h>
 #include <asm/cputype.h>
 #include <asm/proc-fns.h>
+#include <asm/spectre.h>
 #include <asm/system_misc.h>
 
+#ifdef CONFIG_ARM_PSCI
+static int __maybe_unused spectre_v2_get_cpu_fw_mitigation_state(void)
+{
+	struct arm_smccc_res res;
+
+	arm_smccc_1_1_invoke(ARM_SMCCC_ARCH_FEATURES_FUNC_ID,
+			     ARM_SMCCC_ARCH_WORKAROUND_1, &res);
+
+	switch ((int)res.a0) {
+	case SMCCC_RET_SUCCESS:
+		return SPECTRE_MITIGATED;
+
+	case SMCCC_ARCH_WORKAROUND_RET_UNAFFECTED:
+		return SPECTRE_UNAFFECTED;
+
+	default:
+		return SPECTRE_VULNERABLE;
+	}
+}
+#else
+static int __maybe_unused spectre_v2_get_cpu_fw_mitigation_state(void)
+{
+	return SPECTRE_VULNERABLE;
+}
+#endif
+
 #ifdef CONFIG_HARDEN_BRANCH_PREDICTOR
 DEFINE_PER_CPU(harden_branch_predictor_fn_t, harden_branch_predictor_fn);
 
@@ -36,13 +63,60 @@ static void __maybe_unused call_hvc_arch_workaround_1(void)
 	arm_smccc_1_1_hvc(ARM_SMCCC_ARCH_WORKAROUND_1, NULL);
 }
 
-static void cpu_v7_spectre_init(void)
+static unsigned int spectre_v2_install_workaround(unsigned int method)
 {
 	const char *spectre_v2_method = NULL;
 	int cpu = smp_processor_id();
 
 	if (per_cpu(harden_branch_predictor_fn, cpu))
-		return;
+		return SPECTRE_MITIGATED;
+
+	switch (method) {
+	case SPECTRE_V2_METHOD_BPIALL:
+		per_cpu(harden_branch_predictor_fn, cpu) =
+			harden_branch_predictor_bpiall;
+		spectre_v2_method = "BPIALL";
+		break;
+
+	case SPECTRE_V2_METHOD_ICIALLU:
+		per_cpu(harden_branch_predictor_fn, cpu) =
+			harden_branch_predictor_iciallu;
+		spectre_v2_method = "ICIALLU";
+		break;
+
+	case SPECTRE_V2_METHOD_HVC:
+		per_cpu(harden_branch_predictor_fn, cpu) =
+			call_hvc_arch_workaround_1;
+		cpu_do_switch_mm = cpu_v7_hvc_switch_mm;
+		spectre_v2_method = "hypervisor";
+		break;
+
+	case SPECTRE_V2_METHOD_SMC:
+		per_cpu(harden_branch_predictor_fn, cpu) =
+			call_smc_arch_workaround_1;
+		cpu_do_switch_mm = cpu_v7_smc_switch_mm;
+		spectre_v2_method = "firmware";
+		break;
+	}
+
+	if (spectre_v2_method)
+		pr_info("CPU%u: Spectre v2: using %s workaround\n",
+			smp_processor_id(), spectre_v2_method);
+
+	return SPECTRE_MITIGATED;
+}
+#else
+static unsigned int spectre_v2_install_workaround(unsigned int method)
+{
+	pr_info_once("Spectre V2: workarounds disabled by configuration\n");
+
+	return SPECTRE_VULNERABLE;
+}
+#endif
+
+static void cpu_v7_spectre_v2_init(void)
+{
+	unsigned int state, method = 0;
 
 	switch (read_cpuid_part()) {
 	case ARM_CPU_PART_CORTEX_A8:
@@ -51,69 +125,133 @@ static void cpu_v7_spectre_init(void)
 	case ARM_CPU_PART_CORTEX_A17:
 	case ARM_CPU_PART_CORTEX_A73:
 	case ARM_CPU_PART_CORTEX_A75:
-		per_cpu(harden_branch_predictor_fn, cpu) =
-			harden_branch_predictor_bpiall;
-		spectre_v2_method = "BPIALL";
+		state = SPECTRE_MITIGATED;
+		method = SPECTRE_V2_METHOD_BPIALL;
 		break;
 
 	case ARM_CPU_PART_CORTEX_A15:
 	case ARM_CPU_PART_BRAHMA_B15:
-		per_cpu(harden_branch_predictor_fn, cpu) =
-			harden_branch_predictor_iciallu;
-		spectre_v2_method = "ICIALLU";
+		state = SPECTRE_MITIGATED;
+		method = SPECTRE_V2_METHOD_ICIALLU;
 		break;
 
-#ifdef CONFIG_ARM_PSCI
 	case ARM_CPU_PART_BRAHMA_B53:
 		/* Requires no workaround */
+		state = SPECTRE_UNAFFECTED;
 		break;
+
 	default:
 		/* Other ARM CPUs require no workaround */
-		if (read_cpuid_implementor() == ARM_CPU_IMP_ARM)
+		if (read_cpuid_implementor() == ARM_CPU_IMP_ARM) {
+			state = SPECTRE_UNAFFECTED;
 			break;
+		}
+
 		fallthrough;
-		/* Cortex A57/A72 require firmware workaround */
-	case ARM_CPU_PART_CORTEX_A57:
-	case ARM_CPU_PART_CORTEX_A72: {
-		struct arm_smccc_res res;
 
-		arm_smccc_1_1_invoke(ARM_SMCCC_ARCH_FEATURES_FUNC_ID,
-				     ARM_SMCCC_ARCH_WORKAROUND_1, &res);
-		if ((int)res.a0 != 0)
-			return;
+	/* Cortex A57/A72 require firmware workaround */
+	case ARM_CPU_PART_CORTEX_A57:
+	case ARM_CPU_PART_CORTEX_A72:
+		state = spectre_v2_get_cpu_fw_mitigation_state();
+		if (state != SPECTRE_MITIGATED)
+			break;
 
 		switch (arm_smccc_1_1_get_conduit()) {
 		case SMCCC_CONDUIT_HVC:
-			per_cpu(harden_branch_predictor_fn, cpu) =
-				call_hvc_arch_workaround_1;
-			cpu_do_switch_mm = cpu_v7_hvc_switch_mm;
-			spectre_v2_method = "hypervisor";
+			method = SPECTRE_V2_METHOD_HVC;
 			break;
 
 		case SMCCC_CONDUIT_SMC:
-			per_cpu(harden_branch_predictor_fn, cpu) =
-				call_smc_arch_workaround_1;
-			cpu_do_switch_mm = cpu_v7_smc_switch_mm;
-			spectre_v2_method = "firmware";
+			method = SPECTRE_V2_METHOD_SMC;
 			break;
 
 		default:
+			state = SPECTRE_VULNERABLE;
 			break;
 		}
 	}
-#endif
+
+	if (state == SPECTRE_MITIGATED)
+		state = spectre_v2_install_workaround(method);
+
+	spectre_v2_update_state(state, method);
+}
+
+#ifdef CONFIG_HARDEN_BRANCH_HISTORY
+static int spectre_bhb_method;
+
+static const char *spectre_bhb_method_name(int method)
+{
+	switch (method) {
+	case SPECTRE_V2_METHOD_LOOP8:
+		return "loop";
+
+	case SPECTRE_V2_METHOD_BPIALL:
+		return "BPIALL";
+
+	default:
+		return "unknown";
 	}
+}
 
-	if (spectre_v2_method)
-		pr_info("CPU%u: Spectre v2: using %s workaround\n",
-			smp_processor_id(), spectre_v2_method);
+static int spectre_bhb_install_workaround(int method)
+{
+	if (spectre_bhb_method != method) {
+		if (spectre_bhb_method) {
+			pr_err("CPU%u: Spectre BHB: method disagreement, system vulnerable\n",
+			       smp_processor_id());
+
+			return SPECTRE_VULNERABLE;
+		}
+
+		if (spectre_bhb_update_vectors(method) == SPECTRE_VULNERABLE)
+			return SPECTRE_VULNERABLE;
+
+		spectre_bhb_method = method;
+
+		pr_info("CPU%u: Spectre BHB: enabling %s workaround for all CPUs\n",
+			smp_processor_id(), spectre_bhb_method_name(method));
+	}
+
+	return SPECTRE_MITIGATED;
 }
 #else
-static void cpu_v7_spectre_init(void)
+static int spectre_bhb_install_workaround(int method)
 {
+	return SPECTRE_VULNERABLE;
 }
 #endif
 
+static void cpu_v7_spectre_bhb_init(void)
+{
+	unsigned int state, method = 0;
+
+	switch (read_cpuid_part()) {
+	case ARM_CPU_PART_CORTEX_A15:
+	case ARM_CPU_PART_BRAHMA_B15:
+	case ARM_CPU_PART_CORTEX_A57:
+	case ARM_CPU_PART_CORTEX_A72:
+		state = SPECTRE_MITIGATED;
+		method = SPECTRE_V2_METHOD_LOOP8;
+		break;
+
+	case ARM_CPU_PART_CORTEX_A73:
+	case ARM_CPU_PART_CORTEX_A75:
+		state = SPECTRE_MITIGATED;
+		method = SPECTRE_V2_METHOD_BPIALL;
+		break;
+
+	default:
+		state = SPECTRE_UNAFFECTED;
+		break;
+	}
+
+	if (state == SPECTRE_MITIGATED)
+		state = spectre_bhb_install_workaround(method);
+
+	spectre_v2_update_state(state, method);
+}
+
 static __maybe_unused bool cpu_v7_check_auxcr_set(bool *warned,
 						  u32 mask, const char *msg)
 {
@@ -142,16 +280,18 @@ static bool check_spectre_auxcr(bool *warned, u32 bit)
 void cpu_v7_ca8_ibe(void)
 {
 	if (check_spectre_auxcr(this_cpu_ptr(&spectre_warned), BIT(6)))
-		cpu_v7_spectre_init();
+		cpu_v7_spectre_v2_init();
 }
 
 void cpu_v7_ca15_ibe(void)
 {
 	if (check_spectre_auxcr(this_cpu_ptr(&spectre_warned), BIT(0)))
-		cpu_v7_spectre_init();
+		cpu_v7_spectre_v2_init();
+	cpu_v7_spectre_bhb_init();
 }
 
 void cpu_v7_bugs_init(void)
 {
-	cpu_v7_spectre_init();
+	cpu_v7_spectre_v2_init();
+	cpu_v7_spectre_bhb_init();
 }
diff --git a/arch/arm/mm/proc-v7m.S b/arch/arm/mm/proc-v7m.S
index 84459c1d31b8..335144d50134 100644
--- a/arch/arm/mm/proc-v7m.S
+++ b/arch/arm/mm/proc-v7m.S
@@ -194,6 +194,26 @@ ENDPROC(__v7m_setup)
 .endm
 
 	/*
+	 * Match ARM Cortex-M55 processor.
+	 */
+	.type	__v7m_cm55_proc_info, #object
+__v7m_cm55_proc_info:
+	.long	0x410fd220		/* ARM Cortex-M55 0xD22 */
+	.long	0xff0ffff0		/* Mask off revision, patch release */
+	__v7m_proc __v7m_cm55_proc_info, __v7m_cm7_setup, hwcaps = HWCAP_EDSP, cache_fns = v7m_cache_fns, proc_fns = cm7_processor_functions
+	.size	__v7m_cm55_proc_info, . - __v7m_cm55_proc_info
+
+	/*
+	 * Match ARM Cortex-M33 processor.
+	 */
+	.type	__v7m_cm33_proc_info, #object
+__v7m_cm33_proc_info:
+	.long	0x410fd210		/* ARM Cortex-M33 0xD21 */
+	.long	0xff0ffff0		/* Mask off revision, patch release */
+	__v7m_proc __v7m_cm33_proc_info, __v7m_setup, hwcaps = HWCAP_EDSP
+	.size	__v7m_cm33_proc_info, . - __v7m_cm33_proc_info
+
+	/*
 	 * Match ARM Cortex-M7 processor.
 	 */
 	.type	__v7m_cm7_proc_info, #object
diff --git a/arch/arm/net/bpf_jit_32.c b/arch/arm/net/bpf_jit_32.c
index eeb6dc0ecf46..6a1c9fca5260 100644
--- a/arch/arm/net/bpf_jit_32.c
+++ b/arch/arm/net/bpf_jit_32.c
@@ -163,7 +163,7 @@ static const s8 bpf2a32[][2] = {
 	[BPF_REG_9] = {STACK_OFFSET(BPF_R9_HI), STACK_OFFSET(BPF_R9_LO)},
 	/* Read only Frame Pointer to access Stack */
 	[BPF_REG_FP] = {STACK_OFFSET(BPF_FP_HI), STACK_OFFSET(BPF_FP_LO)},
-	/* Temporary Register for internal BPF JIT, can be used
+	/* Temporary Register for BPF JIT, can be used
 	 * for constant blindings and others.
 	 */
 	[TMP_REG_1] = {ARM_R7, ARM_R6},
@@ -712,22 +712,6 @@ static inline void emit_alu_r(const u8 dst, const u8 src, const bool is64,
 	}
 }
 
-/* ALU operation (32 bit)
- * dst = dst (op) src
- */
-static inline void emit_a32_alu_r(const s8 dst, const s8 src,
-				  struct jit_ctx *ctx, const bool is64,
-				  const bool hi, const u8 op) {
-	const s8 *tmp = bpf2a32[TMP_REG_1];
-	s8 rn, rd;
-
-	rn = arm_bpf_get_reg32(src, tmp[1], ctx);
-	rd = arm_bpf_get_reg32(dst, tmp[0], ctx);
-	/* ALU operation */
-	emit_alu_r(rd, rn, is64, hi, op, ctx);
-	arm_bpf_put_reg32(dst, rd, ctx);
-}
-
 /* ALU operation (64 bit) */
 static inline void emit_a32_alu_r64(const bool is64, const s8 dst[],
 				  const s8 src[], struct jit_ctx *ctx,
@@ -1199,7 +1183,8 @@ static int emit_bpf_tail_call(struct jit_ctx *ctx)
 
 	/* tmp2[0] = array, tmp2[1] = index */
 
-	/* if (tail_call_cnt > MAX_TAIL_CALL_CNT)
+	/*
+	 * if (tail_call_cnt >= MAX_TAIL_CALL_CNT)
 	 *	goto out;
 	 * tail_call_cnt++;
 	 */
@@ -1208,7 +1193,7 @@ static int emit_bpf_tail_call(struct jit_ctx *ctx)
 	tc = arm_bpf_get_reg64(tcc, tmp, ctx);
 	emit(ARM_CMP_I(tc[0], hi), ctx);
 	_emit(ARM_COND_EQ, ARM_CMP_I(tc[1], lo), ctx);
-	_emit(ARM_COND_HI, ARM_B(jmp_offset), ctx);
+	_emit(ARM_COND_CS, ARM_B(jmp_offset), ctx);
 	emit(ARM_ADDS_I(tc[1], tc[1], 1), ctx);
 	emit(ARM_ADC_I(tc[0], tc[0], 0), ctx);
 	arm_bpf_put_reg64(tcc, tmp, ctx);
@@ -1863,7 +1848,7 @@ static int build_body(struct jit_ctx *ctx)
 		if (ctx->target == NULL)
 			ctx->offsets[i] = ctx->idx;
 
-		/* If unsuccesfull, return with error code */
+		/* If unsuccesful, return with error code */
 		if (ret)
 			return ret;
 	}
@@ -1972,7 +1957,7 @@ struct bpf_prog *bpf_int_jit_compile(struct bpf_prog *prog)
 	 * for jit, although it can decrease the size of the image.
 	 *
 	 * As each arm instruction is of length 32bit, we are translating
-	 * number of JITed intructions into the size required to store these
+	 * number of JITed instructions into the size required to store these
 	 * JITed code.
 	 */
 	image_size = sizeof(u32) * ctx.idx;
diff --git a/arch/arm/plat-omap/Kconfig b/arch/arm/plat-omap/Kconfig
deleted file mode 100644
index 272670ef1e92..000000000000
--- a/arch/arm/plat-omap/Kconfig
+++ /dev/null
@@ -1,119 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0
-config ARCH_OMAP
-	bool
-
-if ARCH_OMAP
-
-menu "TI OMAP Common Features"
-
-config ARCH_OMAP_OTG
-	bool
-
-comment "OMAP Feature Selections"
-
-config OMAP_DEBUG_DEVICES
-	bool
-	help
-	  For debug cards on TI reference boards.
-
-config OMAP_DEBUG_LEDS
-	def_bool y if NEW_LEDS
-	depends on OMAP_DEBUG_DEVICES
-	select LEDS_CLASS
-
-config POWER_AVS_OMAP
-	bool "AVS(Adaptive Voltage Scaling) support for OMAP IP versions 1&2"
-	depends on (ARCH_OMAP3 || ARCH_OMAP4) && PM
-	select POWER_SUPPLY
-	help
-	  Say Y to enable AVS(Adaptive Voltage Scaling)
-	  support on OMAP containing the version 1 or
-	  version 2 of the SmartReflex IP.
-	  V1 is the 65nm version used in OMAP3430.
-	  V2 is the update for the 45nm version of the IP used in OMAP3630
-	  and OMAP4430
-
-	  Please note, that by default SmartReflex is only
-	  initialized and not enabled. To enable the automatic voltage
-	  compensation for vdd mpu and vdd core from user space,
-	  user must write 1 to
-		/debug/smartreflex/sr_<X>/autocomp,
-	  where X is mpu_iva or core for OMAP3.
-	  Optionally autocompensation can be enabled in the kernel
-	  by default during system init via the enable_on_init flag
-	  which an be passed as platform data to the smartreflex driver.
-
-config POWER_AVS_OMAP_CLASS3
-	bool "Class 3 mode of Smartreflex Implementation"
-	depends on POWER_AVS_OMAP && TWL4030_CORE
-	help
-	  Say Y to enable Class 3 implementation of Smartreflex
-
-	  Class 3 implementation of Smartreflex employs continuous hardware
-	  voltage calibration.
-
-config OMAP_RESET_CLOCKS
-	bool "Reset unused clocks during boot"
-	depends on ARCH_OMAP
-	help
-	  Say Y if you want to reset unused clocks during boot.
-	  This option saves power, but assumes all drivers are
-	  using the clock framework. Broken drivers that do not
-	  yet use clock framework may not work with this option.
-	  If you are booting from another operating system, you
-	  probably do not want this option enabled until your
-	  device drivers work properly.
-
-config OMAP_MPU_TIMER
-	bool "Use mpu timer"
-	depends on ARCH_OMAP1
-	help
-	  Select this option if you want to use the OMAP mpu timer. This
-	  timer provides more intra-tick resolution than the 32KHz timer,
-	  but consumes more power.
-
-config OMAP_32K_TIMER
-	bool "Use 32KHz timer"
-	depends on ARCH_OMAP16XX || ARCH_OMAP2PLUS
-	default y if (ARCH_OMAP16XX || ARCH_OMAP2PLUS)
-	help
-	  Select this option if you want to enable the OMAP 32KHz timer.
-	  This timer saves power compared to the OMAP_MPU_TIMER, and has
-	  support for no tick during idle. The 32KHz timer provides less
-	  intra-tick resolution than OMAP_MPU_TIMER. The 32KHz timer is
-	  currently only available for OMAP16XX, 24XX, 34XX, OMAP4/5 and DRA7XX.
-
-	  On OMAP2PLUS this value is only used for CONFIG_HZ and
-	  CLOCK_TICK_RATE compile time calculation.
-	  The actual timer selection is done in the board file
-	  through the (DT_)MACHINE_START structure.
-
-
-config OMAP3_L2_AUX_SECURE_SAVE_RESTORE
-	bool "OMAP3 HS/EMU save and restore for L2 AUX control register"
-	depends on ARCH_OMAP3 && PM
-	help
-	  Without this option, L2 Auxiliary control register contents are
-	  lost during off-mode entry on HS/EMU devices. This feature
-	  requires support from PPA / boot-loader in HS/EMU devices, which
-	  currently does not exist by default.
-
-config OMAP3_L2_AUX_SECURE_SERVICE_SET_ID
-	int "Service ID for the support routine to set L2 AUX control"
-	depends on OMAP3_L2_AUX_SECURE_SAVE_RESTORE
-	default 43
-	help
-	  PPA routine service ID for setting L2 auxiliary control register.
-
-config OMAP_SERIAL_WAKE
-	bool "Enable wake-up events for serial ports"
-	depends on ARCH_OMAP1 && OMAP_MUX
-	default y
-	help
-	  Select this option if you want to have your system wake up
-	  to data on the serial RX line. This allows you to wake the
-	  system from serial console.
-
-endmenu
-
-endif
diff --git a/arch/arm/plat-omap/Makefile b/arch/arm/plat-omap/Makefile
deleted file mode 100644
index 371f2ed00eda..000000000000
--- a/arch/arm/plat-omap/Makefile
+++ /dev/null
@@ -1,13 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0-only
-#
-# Makefile for the linux kernel.
-#
-
-ccflags-$(CONFIG_ARCH_MULTIPLATFORM) := -I$(srctree)/arch/arm/plat-omap/include
-
-# Common support
-obj-y := sram.o dma.o counter_32k.o
-
-# omap_device support (OMAP2+ only at the moment)
-
-obj-$(CONFIG_OMAP_DEBUG_LEDS) += debug-leds.o
diff --git a/arch/arm/plat-omap/counter_32k.c b/arch/arm/plat-omap/counter_32k.c
deleted file mode 100644
index 7a729ade2105..000000000000
--- a/arch/arm/plat-omap/counter_32k.c
+++ /dev/null
@@ -1,114 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * OMAP 32ksynctimer/counter_32k-related code
- *
- * Copyright (C) 2009 Texas Instruments
- * Copyright (C) 2010 Nokia Corporation
- * Tony Lindgren <tony@atomide.com>
- * Added OMAP4 support - Santosh Shilimkar <santosh.shilimkar@ti.com>
- *
- * NOTE: This timer is not the same timer as the old OMAP1 MPU timer.
- */
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/clk.h>
-#include <linux/err.h>
-#include <linux/io.h>
-#include <linux/clocksource.h>
-#include <linux/sched_clock.h>
-
-#include <asm/mach/time.h>
-
-#include <plat/counter-32k.h>
-
-/* OMAP2_32KSYNCNT_CR_OFF: offset of 32ksync counter register */
-#define OMAP2_32KSYNCNT_REV_OFF		0x0
-#define OMAP2_32KSYNCNT_REV_SCHEME	(0x3 << 30)
-#define OMAP2_32KSYNCNT_CR_OFF_LOW	0x10
-#define OMAP2_32KSYNCNT_CR_OFF_HIGH	0x30
-
-/*
- * 32KHz clocksource ... always available, on pretty most chips except
- * OMAP 730 and 1510.  Other timers could be used as clocksources, with
- * higher resolution in free-running counter modes (e.g. 12 MHz xtal),
- * but systems won't necessarily want to spend resources that way.
- */
-static void __iomem *sync32k_cnt_reg;
-
-static u64 notrace omap_32k_read_sched_clock(void)
-{
-	return sync32k_cnt_reg ? readl_relaxed(sync32k_cnt_reg) : 0;
-}
-
-/**
- * omap_read_persistent_clock64 -  Return time from a persistent clock.
- *
- * Reads the time from a source which isn't disabled during PM, the
- * 32k sync timer.  Convert the cycles elapsed since last read into
- * nsecs and adds to a monotonically increasing timespec64.
- */
-static struct timespec64 persistent_ts;
-static cycles_t cycles;
-static unsigned int persistent_mult, persistent_shift;
-
-static void omap_read_persistent_clock64(struct timespec64 *ts)
-{
-	unsigned long long nsecs;
-	cycles_t last_cycles;
-
-	last_cycles = cycles;
-	cycles = sync32k_cnt_reg ? readl_relaxed(sync32k_cnt_reg) : 0;
-
-	nsecs = clocksource_cyc2ns(cycles - last_cycles,
-					persistent_mult, persistent_shift);
-
-	timespec64_add_ns(&persistent_ts, nsecs);
-
-	*ts = persistent_ts;
-}
-
-/**
- * omap_init_clocksource_32k - setup and register counter 32k as a
- * kernel clocksource
- * @pbase: base addr of counter_32k module
- * @size: size of counter_32k to map
- *
- * Returns 0 upon success or negative error code upon failure.
- *
- */
-int __init omap_init_clocksource_32k(void __iomem *vbase)
-{
-	int ret;
-
-	/*
-	 * 32k sync Counter IP register offsets vary between the
-	 * highlander version and the legacy ones.
-	 * The 'SCHEME' bits(30-31) of the revision register is used
-	 * to identify the version.
-	 */
-	if (readl_relaxed(vbase + OMAP2_32KSYNCNT_REV_OFF) &
-						OMAP2_32KSYNCNT_REV_SCHEME)
-		sync32k_cnt_reg = vbase + OMAP2_32KSYNCNT_CR_OFF_HIGH;
-	else
-		sync32k_cnt_reg = vbase + OMAP2_32KSYNCNT_CR_OFF_LOW;
-
-	/*
-	 * 120000 rough estimate from the calculations in
-	 * __clocksource_update_freq_scale.
-	 */
-	clocks_calc_mult_shift(&persistent_mult, &persistent_shift,
-			32768, NSEC_PER_SEC, 120000);
-
-	ret = clocksource_mmio_init(sync32k_cnt_reg, "32k_counter", 32768,
-				250, 32, clocksource_mmio_readl_up);
-	if (ret) {
-		pr_err("32k_counter: can't register clocksource\n");
-		return ret;
-	}
-
-	sched_clock_register(omap_32k_read_sched_clock, 32, 32768);
-	register_persistent_clock(omap_read_persistent_clock64);
-	pr_info("OMAP clocksource: 32k_counter at 32768 Hz\n");
-
-	return 0;
-}
diff --git a/arch/arm/plat-omap/debug-leds.c b/arch/arm/plat-omap/debug-leds.c
deleted file mode 100644
index 2b698d074874..000000000000
--- a/arch/arm/plat-omap/debug-leds.c
+++ /dev/null
@@ -1,171 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * linux/arch/arm/plat-omap/debug-leds.c
- *
- * Copyright 2011 by Bryan Wu <bryan.wu@canonical.com>
- * Copyright 2003 by Texas Instruments Incorporated
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/platform_device.h>
-#include <linux/leds.h>
-#include <linux/io.h>
-#include <linux/platform_data/gpio-omap.h>
-#include <linux/slab.h>
-
-#include <asm/mach-types.h>
-
-/* Many OMAP development platforms reuse the same "debug board"; these
- * platforms include H2, H3, H4, and Perseus2.  There are 16 LEDs on the
- * debug board (all green), accessed through FPGA registers.
- */
-
-/* NOTE:  most boards don't have a static mapping for the FPGA ... */
-struct h2p2_dbg_fpga {
-	/* offset 0x00 */
-	u16		smc91x[8];
-	/* offset 0x10 */
-	u16		fpga_rev;
-	u16		board_rev;
-	u16		gpio_outputs;
-	u16		leds;
-	/* offset 0x18 */
-	u16		misc_inputs;
-	u16		lan_status;
-	u16		lan_reset;
-	u16		reserved0;
-	/* offset 0x20 */
-	u16		ps2_data;
-	u16		ps2_ctrl;
-	/* plus also 4 rs232 ports ... */
-};
-
-static struct h2p2_dbg_fpga __iomem *fpga;
-
-static u16 fpga_led_state;
-
-struct dbg_led {
-	struct led_classdev	cdev;
-	u16			mask;
-};
-
-static const struct {
-	const char *name;
-	const char *trigger;
-} dbg_leds[] = {
-	{ "dbg:d4", "heartbeat", },
-	{ "dbg:d5", "cpu0", },
-	{ "dbg:d6", "default-on", },
-	{ "dbg:d7", },
-	{ "dbg:d8", },
-	{ "dbg:d9", },
-	{ "dbg:d10", },
-	{ "dbg:d11", },
-	{ "dbg:d12", },
-	{ "dbg:d13", },
-	{ "dbg:d14", },
-	{ "dbg:d15", },
-	{ "dbg:d16", },
-	{ "dbg:d17", },
-	{ "dbg:d18", },
-	{ "dbg:d19", },
-};
-
-/*
- * The triggers lines up below will only be used if the
- * LED triggers are compiled in.
- */
-static void dbg_led_set(struct led_classdev *cdev,
-			      enum led_brightness b)
-{
-	struct dbg_led *led = container_of(cdev, struct dbg_led, cdev);
-	u16 reg;
-
-	reg = readw_relaxed(&fpga->leds);
-	if (b != LED_OFF)
-		reg |= led->mask;
-	else
-		reg &= ~led->mask;
-	writew_relaxed(reg, &fpga->leds);
-}
-
-static enum led_brightness dbg_led_get(struct led_classdev *cdev)
-{
-	struct dbg_led *led = container_of(cdev, struct dbg_led, cdev);
-	u16 reg;
-
-	reg = readw_relaxed(&fpga->leds);
-	return (reg & led->mask) ? LED_FULL : LED_OFF;
-}
-
-static int fpga_probe(struct platform_device *pdev)
-{
-	struct resource	*iomem;
-	int i;
-
-	iomem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	if (!iomem)
-		return -ENODEV;
-
-	fpga = ioremap(iomem->start, resource_size(iomem));
-	writew_relaxed(0xff, &fpga->leds);
-
-	for (i = 0; i < ARRAY_SIZE(dbg_leds); i++) {
-		struct dbg_led *led;
-
-		led = kzalloc(sizeof(*led), GFP_KERNEL);
-		if (!led)
-			break;
-
-		led->cdev.name = dbg_leds[i].name;
-		led->cdev.brightness_set = dbg_led_set;
-		led->cdev.brightness_get = dbg_led_get;
-		led->cdev.default_trigger = dbg_leds[i].trigger;
-		led->mask = BIT(i);
-
-		if (led_classdev_register(NULL, &led->cdev) < 0) {
-			kfree(led);
-			break;
-		}
-	}
-
-	return 0;
-}
-
-static int fpga_suspend_noirq(struct device *dev)
-{
-	fpga_led_state = readw_relaxed(&fpga->leds);
-	writew_relaxed(0xff, &fpga->leds);
-
-	return 0;
-}
-
-static int fpga_resume_noirq(struct device *dev)
-{
-	writew_relaxed(~fpga_led_state, &fpga->leds);
-	return 0;
-}
-
-static const struct dev_pm_ops fpga_dev_pm_ops = {
-	.suspend_noirq = fpga_suspend_noirq,
-	.resume_noirq = fpga_resume_noirq,
-};
-
-static struct platform_driver led_driver = {
-	.driver.name	= "omap_dbg_led",
-	.driver.pm	= &fpga_dev_pm_ops,
-	.probe		= fpga_probe,
-};
-
-static int __init fpga_init(void)
-{
-	if (machine_is_omap_h4()
-			|| machine_is_omap_h3()
-			|| machine_is_omap_h2()
-			|| machine_is_omap_perseus2()
-			)
-		return platform_driver_register(&led_driver);
-	return 0;
-}
-fs_initcall(fpga_init);
diff --git a/arch/arm/plat-omap/dma.c b/arch/arm/plat-omap/dma.c
deleted file mode 100644
index 9f11de46aaa9..000000000000
--- a/arch/arm/plat-omap/dma.c
+++ /dev/null
@@ -1,1003 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * linux/arch/arm/plat-omap/dma.c
- *
- * Copyright (C) 2003 - 2008 Nokia Corporation
- * Author: Juha Yrjölä <juha.yrjola@nokia.com>
- * DMA channel linking for 1610 by Samuel Ortiz <samuel.ortiz@nokia.com>
- * Graphics DMA and LCD DMA graphics tranformations
- * by Imre Deak <imre.deak@nokia.com>
- * OMAP2/3 support Copyright (C) 2004-2007 Texas Instruments, Inc.
- * Merged to support both OMAP1 and OMAP2 by Tony Lindgren <tony@atomide.com>
- * Some functions based on earlier dma-omap.c Copyright (C) 2001 RidgeRun, Inc.
- *
- * Copyright (C) 2009 Texas Instruments
- * Added OMAP4 support - Santosh Shilimkar <santosh.shilimkar@ti.com>
- *
- * Support functions for the OMAP internal DMA channels.
- *
- * Copyright (C) 2010 Texas Instruments Incorporated - https://www.ti.com/
- * Converted DMA library into DMA platform driver.
- *	- G, Manjunath Kondaiah <manjugk@ti.com>
- */
-
-#include <linux/module.h>
-#include <linux/init.h>
-#include <linux/sched.h>
-#include <linux/spinlock.h>
-#include <linux/errno.h>
-#include <linux/interrupt.h>
-#include <linux/irq.h>
-#include <linux/io.h>
-#include <linux/slab.h>
-#include <linux/delay.h>
-
-#include <linux/omap-dma.h>
-
-#ifdef CONFIG_ARCH_OMAP1
-#include <mach/soc.h>
-#endif
-
-/*
- * MAX_LOGICAL_DMA_CH_COUNT: the maximum number of logical DMA
- * channels that an instance of the SDMA IP block can support.  Used
- * to size arrays.  (The actual maximum on a particular SoC may be less
- * than this -- for example, OMAP1 SDMA instances only support 17 logical
- * DMA channels.)
- */
-#define MAX_LOGICAL_DMA_CH_COUNT		32
-
-#undef DEBUG
-
-#ifndef CONFIG_ARCH_OMAP1
-enum { DMA_CH_ALLOC_DONE, DMA_CH_PARAMS_SET_DONE, DMA_CH_STARTED,
-	DMA_CH_QUEUED, DMA_CH_NOTSTARTED, DMA_CH_PAUSED, DMA_CH_LINK_ENABLED
-};
-
-enum { DMA_CHAIN_STARTED, DMA_CHAIN_NOTSTARTED };
-#endif
-
-#define OMAP_DMA_ACTIVE			0x01
-#define OMAP2_DMA_CSR_CLEAR_MASK	0xffffffff
-
-#define OMAP_FUNC_MUX_ARM_BASE		(0xfffe1000 + 0xec)
-
-static struct omap_system_dma_plat_info *p;
-static struct omap_dma_dev_attr *d;
-static void omap_clear_dma(int lch);
-static int enable_1510_mode;
-static u32 errata;
-
-struct dma_link_info {
-	int *linked_dmach_q;
-	int no_of_lchs_linked;
-
-	int q_count;
-	int q_tail;
-	int q_head;
-
-	int chain_state;
-	int chain_mode;
-
-};
-
-static int dma_lch_count;
-static int dma_chan_count;
-static int omap_dma_reserve_channels;
-
-static DEFINE_SPINLOCK(dma_chan_lock);
-static struct omap_dma_lch *dma_chan;
-
-static inline void disable_lnk(int lch);
-static void omap_disable_channel_irq(int lch);
-static inline void omap_enable_channel_irq(int lch);
-
-#ifdef CONFIG_ARCH_OMAP15XX
-/* Returns 1 if the DMA module is in OMAP1510-compatible mode, 0 otherwise */
-static int omap_dma_in_1510_mode(void)
-{
-	return enable_1510_mode;
-}
-#else
-#define omap_dma_in_1510_mode()		0
-#endif
-
-#ifdef CONFIG_ARCH_OMAP1
-static inline void set_gdma_dev(int req, int dev)
-{
-	u32 reg = OMAP_FUNC_MUX_ARM_BASE + ((req - 1) / 5) * 4;
-	int shift = ((req - 1) % 5) * 6;
-	u32 l;
-
-	l = omap_readl(reg);
-	l &= ~(0x3f << shift);
-	l |= (dev - 1) << shift;
-	omap_writel(l, reg);
-}
-#else
-#define set_gdma_dev(req, dev)	do {} while (0)
-#define omap_readl(reg)		0
-#define omap_writel(val, reg)	do {} while (0)
-#endif
-
-#ifdef CONFIG_ARCH_OMAP1
-void omap_set_dma_priority(int lch, int dst_port, int priority)
-{
-	unsigned long reg;
-	u32 l;
-
-	if (dma_omap1()) {
-		switch (dst_port) {
-		case OMAP_DMA_PORT_OCP_T1:	/* FFFECC00 */
-			reg = OMAP_TC_OCPT1_PRIOR;
-			break;
-		case OMAP_DMA_PORT_OCP_T2:	/* FFFECCD0 */
-			reg = OMAP_TC_OCPT2_PRIOR;
-			break;
-		case OMAP_DMA_PORT_EMIFF:	/* FFFECC08 */
-			reg = OMAP_TC_EMIFF_PRIOR;
-			break;
-		case OMAP_DMA_PORT_EMIFS:	/* FFFECC04 */
-			reg = OMAP_TC_EMIFS_PRIOR;
-			break;
-		default:
-			BUG();
-			return;
-		}
-		l = omap_readl(reg);
-		l &= ~(0xf << 8);
-		l |= (priority & 0xf) << 8;
-		omap_writel(l, reg);
-	}
-}
-#endif
-
-#ifdef CONFIG_ARCH_OMAP2PLUS
-void omap_set_dma_priority(int lch, int dst_port, int priority)
-{
-	u32 ccr;
-
-	ccr = p->dma_read(CCR, lch);
-	if (priority)
-		ccr |= (1 << 6);
-	else
-		ccr &= ~(1 << 6);
-	p->dma_write(ccr, CCR, lch);
-}
-#endif
-EXPORT_SYMBOL(omap_set_dma_priority);
-
-void omap_set_dma_transfer_params(int lch, int data_type, int elem_count,
-				  int frame_count, int sync_mode,
-				  int dma_trigger, int src_or_dst_synch)
-{
-	u32 l;
-
-	l = p->dma_read(CSDP, lch);
-	l &= ~0x03;
-	l |= data_type;
-	p->dma_write(l, CSDP, lch);
-
-	if (dma_omap1()) {
-		u16 ccr;
-
-		ccr = p->dma_read(CCR, lch);
-		ccr &= ~(1 << 5);
-		if (sync_mode == OMAP_DMA_SYNC_FRAME)
-			ccr |= 1 << 5;
-		p->dma_write(ccr, CCR, lch);
-
-		ccr = p->dma_read(CCR2, lch);
-		ccr &= ~(1 << 2);
-		if (sync_mode == OMAP_DMA_SYNC_BLOCK)
-			ccr |= 1 << 2;
-		p->dma_write(ccr, CCR2, lch);
-	}
-
-	if (dma_omap2plus() && dma_trigger) {
-		u32 val;
-
-		val = p->dma_read(CCR, lch);
-
-		/* DMA_SYNCHRO_CONTROL_UPPER depends on the channel number */
-		val &= ~((1 << 23) | (3 << 19) | 0x1f);
-		val |= (dma_trigger & ~0x1f) << 14;
-		val |= dma_trigger & 0x1f;
-
-		if (sync_mode & OMAP_DMA_SYNC_FRAME)
-			val |= 1 << 5;
-		else
-			val &= ~(1 << 5);
-
-		if (sync_mode & OMAP_DMA_SYNC_BLOCK)
-			val |= 1 << 18;
-		else
-			val &= ~(1 << 18);
-
-		if (src_or_dst_synch == OMAP_DMA_DST_SYNC_PREFETCH) {
-			val &= ~(1 << 24);	/* dest synch */
-			val |= (1 << 23);	/* Prefetch */
-		} else if (src_or_dst_synch) {
-			val |= 1 << 24;		/* source synch */
-		} else {
-			val &= ~(1 << 24);	/* dest synch */
-		}
-		p->dma_write(val, CCR, lch);
-	}
-
-	p->dma_write(elem_count, CEN, lch);
-	p->dma_write(frame_count, CFN, lch);
-}
-EXPORT_SYMBOL(omap_set_dma_transfer_params);
-
-void omap_set_dma_channel_mode(int lch, enum omap_dma_channel_mode mode)
-{
-	if (dma_omap1() && !dma_omap15xx()) {
-		u32 l;
-
-		l = p->dma_read(LCH_CTRL, lch);
-		l &= ~0x7;
-		l |= mode;
-		p->dma_write(l, LCH_CTRL, lch);
-	}
-}
-EXPORT_SYMBOL(omap_set_dma_channel_mode);
-
-/* Note that src_port is only for omap1 */
-void omap_set_dma_src_params(int lch, int src_port, int src_amode,
-			     unsigned long src_start,
-			     int src_ei, int src_fi)
-{
-	u32 l;
-
-	if (dma_omap1()) {
-		u16 w;
-
-		w = p->dma_read(CSDP, lch);
-		w &= ~(0x1f << 2);
-		w |= src_port << 2;
-		p->dma_write(w, CSDP, lch);
-	}
-
-	l = p->dma_read(CCR, lch);
-	l &= ~(0x03 << 12);
-	l |= src_amode << 12;
-	p->dma_write(l, CCR, lch);
-
-	p->dma_write(src_start, CSSA, lch);
-
-	p->dma_write(src_ei, CSEI, lch);
-	p->dma_write(src_fi, CSFI, lch);
-}
-EXPORT_SYMBOL(omap_set_dma_src_params);
-
-void omap_set_dma_src_data_pack(int lch, int enable)
-{
-	u32 l;
-
-	l = p->dma_read(CSDP, lch);
-	l &= ~(1 << 6);
-	if (enable)
-		l |= (1 << 6);
-	p->dma_write(l, CSDP, lch);
-}
-EXPORT_SYMBOL(omap_set_dma_src_data_pack);
-
-void omap_set_dma_src_burst_mode(int lch, enum omap_dma_burst_mode burst_mode)
-{
-	unsigned int burst = 0;
-	u32 l;
-
-	l = p->dma_read(CSDP, lch);
-	l &= ~(0x03 << 7);
-
-	switch (burst_mode) {
-	case OMAP_DMA_DATA_BURST_DIS:
-		break;
-	case OMAP_DMA_DATA_BURST_4:
-		if (dma_omap2plus())
-			burst = 0x1;
-		else
-			burst = 0x2;
-		break;
-	case OMAP_DMA_DATA_BURST_8:
-		if (dma_omap2plus()) {
-			burst = 0x2;
-			break;
-		}
-		/*
-		 * not supported by current hardware on OMAP1
-		 * w |= (0x03 << 7);
-		 */
-		fallthrough;
-	case OMAP_DMA_DATA_BURST_16:
-		if (dma_omap2plus()) {
-			burst = 0x3;
-			break;
-		}
-		/* OMAP1 don't support burst 16 */
-		fallthrough;
-	default:
-		BUG();
-	}
-
-	l |= (burst << 7);
-	p->dma_write(l, CSDP, lch);
-}
-EXPORT_SYMBOL(omap_set_dma_src_burst_mode);
-
-/* Note that dest_port is only for OMAP1 */
-void omap_set_dma_dest_params(int lch, int dest_port, int dest_amode,
-			      unsigned long dest_start,
-			      int dst_ei, int dst_fi)
-{
-	u32 l;
-
-	if (dma_omap1()) {
-		l = p->dma_read(CSDP, lch);
-		l &= ~(0x1f << 9);
-		l |= dest_port << 9;
-		p->dma_write(l, CSDP, lch);
-	}
-
-	l = p->dma_read(CCR, lch);
-	l &= ~(0x03 << 14);
-	l |= dest_amode << 14;
-	p->dma_write(l, CCR, lch);
-
-	p->dma_write(dest_start, CDSA, lch);
-
-	p->dma_write(dst_ei, CDEI, lch);
-	p->dma_write(dst_fi, CDFI, lch);
-}
-EXPORT_SYMBOL(omap_set_dma_dest_params);
-
-void omap_set_dma_dest_data_pack(int lch, int enable)
-{
-	u32 l;
-
-	l = p->dma_read(CSDP, lch);
-	l &= ~(1 << 13);
-	if (enable)
-		l |= 1 << 13;
-	p->dma_write(l, CSDP, lch);
-}
-EXPORT_SYMBOL(omap_set_dma_dest_data_pack);
-
-void omap_set_dma_dest_burst_mode(int lch, enum omap_dma_burst_mode burst_mode)
-{
-	unsigned int burst = 0;
-	u32 l;
-
-	l = p->dma_read(CSDP, lch);
-	l &= ~(0x03 << 14);
-
-	switch (burst_mode) {
-	case OMAP_DMA_DATA_BURST_DIS:
-		break;
-	case OMAP_DMA_DATA_BURST_4:
-		if (dma_omap2plus())
-			burst = 0x1;
-		else
-			burst = 0x2;
-		break;
-	case OMAP_DMA_DATA_BURST_8:
-		if (dma_omap2plus())
-			burst = 0x2;
-		else
-			burst = 0x3;
-		break;
-	case OMAP_DMA_DATA_BURST_16:
-		if (dma_omap2plus()) {
-			burst = 0x3;
-			break;
-		}
-		/* OMAP1 don't support burst 16 */
-		fallthrough;
-	default:
-		printk(KERN_ERR "Invalid DMA burst mode\n");
-		BUG();
-		return;
-	}
-	l |= (burst << 14);
-	p->dma_write(l, CSDP, lch);
-}
-EXPORT_SYMBOL(omap_set_dma_dest_burst_mode);
-
-static inline void omap_enable_channel_irq(int lch)
-{
-	/* Clear CSR */
-	if (dma_omap1())
-		p->dma_read(CSR, lch);
-	else
-		p->dma_write(OMAP2_DMA_CSR_CLEAR_MASK, CSR, lch);
-
-	/* Enable some nice interrupts. */
-	p->dma_write(dma_chan[lch].enabled_irqs, CICR, lch);
-}
-
-static inline void omap_disable_channel_irq(int lch)
-{
-	/* disable channel interrupts */
-	p->dma_write(0, CICR, lch);
-	/* Clear CSR */
-	if (dma_omap1())
-		p->dma_read(CSR, lch);
-	else
-		p->dma_write(OMAP2_DMA_CSR_CLEAR_MASK, CSR, lch);
-}
-
-void omap_disable_dma_irq(int lch, u16 bits)
-{
-	dma_chan[lch].enabled_irqs &= ~bits;
-}
-EXPORT_SYMBOL(omap_disable_dma_irq);
-
-static inline void enable_lnk(int lch)
-{
-	u32 l;
-
-	l = p->dma_read(CLNK_CTRL, lch);
-
-	if (dma_omap1())
-		l &= ~(1 << 14);
-
-	/* Set the ENABLE_LNK bits */
-	if (dma_chan[lch].next_lch != -1)
-		l = dma_chan[lch].next_lch | (1 << 15);
-
-	p->dma_write(l, CLNK_CTRL, lch);
-}
-
-static inline void disable_lnk(int lch)
-{
-	u32 l;
-
-	l = p->dma_read(CLNK_CTRL, lch);
-
-	/* Disable interrupts */
-	omap_disable_channel_irq(lch);
-
-	if (dma_omap1()) {
-		/* Set the STOP_LNK bit */
-		l |= 1 << 14;
-	}
-
-	if (dma_omap2plus()) {
-		/* Clear the ENABLE_LNK bit */
-		l &= ~(1 << 15);
-	}
-
-	p->dma_write(l, CLNK_CTRL, lch);
-	dma_chan[lch].flags &= ~OMAP_DMA_ACTIVE;
-}
-
-int omap_request_dma(int dev_id, const char *dev_name,
-		     void (*callback)(int lch, u16 ch_status, void *data),
-		     void *data, int *dma_ch_out)
-{
-	int ch, free_ch = -1;
-	unsigned long flags;
-	struct omap_dma_lch *chan;
-
-	WARN(strcmp(dev_name, "DMA engine"), "Using deprecated platform DMA API - please update to DMA engine");
-
-	spin_lock_irqsave(&dma_chan_lock, flags);
-	for (ch = 0; ch < dma_chan_count; ch++) {
-		if (free_ch == -1 && dma_chan[ch].dev_id == -1) {
-			free_ch = ch;
-			/* Exit after first free channel found */
-			break;
-		}
-	}
-	if (free_ch == -1) {
-		spin_unlock_irqrestore(&dma_chan_lock, flags);
-		return -EBUSY;
-	}
-	chan = dma_chan + free_ch;
-	chan->dev_id = dev_id;
-
-	if (p->clear_lch_regs)
-		p->clear_lch_regs(free_ch);
-
-	spin_unlock_irqrestore(&dma_chan_lock, flags);
-
-	chan->dev_name = dev_name;
-	chan->callback = callback;
-	chan->data = data;
-	chan->flags = 0;
-
-	chan->enabled_irqs = OMAP_DMA_DROP_IRQ | OMAP_DMA_BLOCK_IRQ;
-
-	if (dma_omap1())
-		chan->enabled_irqs |= OMAP1_DMA_TOUT_IRQ;
-
-	if (dma_omap16xx()) {
-		/* If the sync device is set, configure it dynamically. */
-		if (dev_id != 0) {
-			set_gdma_dev(free_ch + 1, dev_id);
-			dev_id = free_ch + 1;
-		}
-		/*
-		 * Disable the 1510 compatibility mode and set the sync device
-		 * id.
-		 */
-		p->dma_write(dev_id | (1 << 10), CCR, free_ch);
-	} else if (dma_omap1()) {
-		p->dma_write(dev_id, CCR, free_ch);
-	}
-
-	*dma_ch_out = free_ch;
-
-	return 0;
-}
-EXPORT_SYMBOL(omap_request_dma);
-
-void omap_free_dma(int lch)
-{
-	unsigned long flags;
-
-	if (dma_chan[lch].dev_id == -1) {
-		pr_err("omap_dma: trying to free unallocated DMA channel %d\n",
-		       lch);
-		return;
-	}
-
-	/* Disable all DMA interrupts for the channel. */
-	omap_disable_channel_irq(lch);
-
-	/* Make sure the DMA transfer is stopped. */
-	p->dma_write(0, CCR, lch);
-
-	spin_lock_irqsave(&dma_chan_lock, flags);
-	dma_chan[lch].dev_id = -1;
-	dma_chan[lch].next_lch = -1;
-	dma_chan[lch].callback = NULL;
-	spin_unlock_irqrestore(&dma_chan_lock, flags);
-}
-EXPORT_SYMBOL(omap_free_dma);
-
-/*
- * Clears any DMA state so the DMA engine is ready to restart with new buffers
- * through omap_start_dma(). Any buffers in flight are discarded.
- */
-static void omap_clear_dma(int lch)
-{
-	unsigned long flags;
-
-	local_irq_save(flags);
-	p->clear_dma(lch);
-	local_irq_restore(flags);
-}
-
-void omap_start_dma(int lch)
-{
-	u32 l;
-
-	/*
-	 * The CPC/CDAC register needs to be initialized to zero
-	 * before starting dma transfer.
-	 */
-	if (dma_omap15xx())
-		p->dma_write(0, CPC, lch);
-	else
-		p->dma_write(0, CDAC, lch);
-
-	if (!omap_dma_in_1510_mode() && dma_chan[lch].next_lch != -1) {
-		int next_lch, cur_lch;
-		char dma_chan_link_map[MAX_LOGICAL_DMA_CH_COUNT];
-
-		/* Set the link register of the first channel */
-		enable_lnk(lch);
-
-		memset(dma_chan_link_map, 0, sizeof(dma_chan_link_map));
-		dma_chan_link_map[lch] = 1;
-
-		cur_lch = dma_chan[lch].next_lch;
-		do {
-			next_lch = dma_chan[cur_lch].next_lch;
-
-			/* The loop case: we've been here already */
-			if (dma_chan_link_map[cur_lch])
-				break;
-			/* Mark the current channel */
-			dma_chan_link_map[cur_lch] = 1;
-
-			enable_lnk(cur_lch);
-			omap_enable_channel_irq(cur_lch);
-
-			cur_lch = next_lch;
-		} while (next_lch != -1);
-	} else if (IS_DMA_ERRATA(DMA_ERRATA_PARALLEL_CHANNELS))
-		p->dma_write(lch, CLNK_CTRL, lch);
-
-	omap_enable_channel_irq(lch);
-
-	l = p->dma_read(CCR, lch);
-
-	if (IS_DMA_ERRATA(DMA_ERRATA_IFRAME_BUFFERING))
-			l |= OMAP_DMA_CCR_BUFFERING_DISABLE;
-	l |= OMAP_DMA_CCR_EN;
-
-	/*
-	 * As dma_write() uses IO accessors which are weakly ordered, there
-	 * is no guarantee that data in coherent DMA memory will be visible
-	 * to the DMA device.  Add a memory barrier here to ensure that any
-	 * such data is visible prior to enabling DMA.
-	 */
-	mb();
-	p->dma_write(l, CCR, lch);
-
-	dma_chan[lch].flags |= OMAP_DMA_ACTIVE;
-}
-EXPORT_SYMBOL(omap_start_dma);
-
-void omap_stop_dma(int lch)
-{
-	u32 l;
-
-	/* Disable all interrupts on the channel */
-	omap_disable_channel_irq(lch);
-
-	l = p->dma_read(CCR, lch);
-	if (IS_DMA_ERRATA(DMA_ERRATA_i541) &&
-			(l & OMAP_DMA_CCR_SEL_SRC_DST_SYNC)) {
-		int i = 0;
-		u32 sys_cf;
-
-		/* Configure No-Standby */
-		l = p->dma_read(OCP_SYSCONFIG, lch);
-		sys_cf = l;
-		l &= ~DMA_SYSCONFIG_MIDLEMODE_MASK;
-		l |= DMA_SYSCONFIG_MIDLEMODE(DMA_IDLEMODE_NO_IDLE);
-		p->dma_write(l , OCP_SYSCONFIG, 0);
-
-		l = p->dma_read(CCR, lch);
-		l &= ~OMAP_DMA_CCR_EN;
-		p->dma_write(l, CCR, lch);
-
-		/* Wait for sDMA FIFO drain */
-		l = p->dma_read(CCR, lch);
-		while (i < 100 && (l & (OMAP_DMA_CCR_RD_ACTIVE |
-					OMAP_DMA_CCR_WR_ACTIVE))) {
-			udelay(5);
-			i++;
-			l = p->dma_read(CCR, lch);
-		}
-		if (i >= 100)
-			pr_err("DMA drain did not complete on lch %d\n", lch);
-		/* Restore OCP_SYSCONFIG */
-		p->dma_write(sys_cf, OCP_SYSCONFIG, lch);
-	} else {
-		l &= ~OMAP_DMA_CCR_EN;
-		p->dma_write(l, CCR, lch);
-	}
-
-	/*
-	 * Ensure that data transferred by DMA is visible to any access
-	 * after DMA has been disabled.  This is important for coherent
-	 * DMA regions.
-	 */
-	mb();
-
-	if (!omap_dma_in_1510_mode() && dma_chan[lch].next_lch != -1) {
-		int next_lch, cur_lch = lch;
-		char dma_chan_link_map[MAX_LOGICAL_DMA_CH_COUNT];
-
-		memset(dma_chan_link_map, 0, sizeof(dma_chan_link_map));
-		do {
-			/* The loop case: we've been here already */
-			if (dma_chan_link_map[cur_lch])
-				break;
-			/* Mark the current channel */
-			dma_chan_link_map[cur_lch] = 1;
-
-			disable_lnk(cur_lch);
-
-			next_lch = dma_chan[cur_lch].next_lch;
-			cur_lch = next_lch;
-		} while (next_lch != -1);
-	}
-
-	dma_chan[lch].flags &= ~OMAP_DMA_ACTIVE;
-}
-EXPORT_SYMBOL(omap_stop_dma);
-
-/*
- * Allows changing the DMA callback function or data. This may be needed if
- * the driver shares a single DMA channel for multiple dma triggers.
- */
-/*
- * Returns current physical source address for the given DMA channel.
- * If the channel is running the caller must disable interrupts prior calling
- * this function and process the returned value before re-enabling interrupt to
- * prevent races with the interrupt handler. Note that in continuous mode there
- * is a chance for CSSA_L register overflow between the two reads resulting
- * in incorrect return value.
- */
-dma_addr_t omap_get_dma_src_pos(int lch)
-{
-	dma_addr_t offset = 0;
-
-	if (dma_omap15xx())
-		offset = p->dma_read(CPC, lch);
-	else
-		offset = p->dma_read(CSAC, lch);
-
-	if (IS_DMA_ERRATA(DMA_ERRATA_3_3) && offset == 0)
-		offset = p->dma_read(CSAC, lch);
-
-	if (!dma_omap15xx()) {
-		/*
-		 * CDAC == 0 indicates that the DMA transfer on the channel has
-		 * not been started (no data has been transferred so far).
-		 * Return the programmed source start address in this case.
-		 */
-		if (likely(p->dma_read(CDAC, lch)))
-			offset = p->dma_read(CSAC, lch);
-		else
-			offset = p->dma_read(CSSA, lch);
-	}
-
-	if (dma_omap1())
-		offset |= (p->dma_read(CSSA, lch) & 0xFFFF0000);
-
-	return offset;
-}
-EXPORT_SYMBOL(omap_get_dma_src_pos);
-
-/*
- * Returns current physical destination address for the given DMA channel.
- * If the channel is running the caller must disable interrupts prior calling
- * this function and process the returned value before re-enabling interrupt to
- * prevent races with the interrupt handler. Note that in continuous mode there
- * is a chance for CDSA_L register overflow between the two reads resulting
- * in incorrect return value.
- */
-dma_addr_t omap_get_dma_dst_pos(int lch)
-{
-	dma_addr_t offset = 0;
-
-	if (dma_omap15xx())
-		offset = p->dma_read(CPC, lch);
-	else
-		offset = p->dma_read(CDAC, lch);
-
-	/*
-	 * omap 3.2/3.3 erratum: sometimes 0 is returned if CSAC/CDAC is
-	 * read before the DMA controller finished disabling the channel.
-	 */
-	if (!dma_omap15xx() && offset == 0) {
-		offset = p->dma_read(CDAC, lch);
-		/*
-		 * CDAC == 0 indicates that the DMA transfer on the channel has
-		 * not been started (no data has been transferred so far).
-		 * Return the programmed destination start address in this case.
-		 */
-		if (unlikely(!offset))
-			offset = p->dma_read(CDSA, lch);
-	}
-
-	if (dma_omap1())
-		offset |= (p->dma_read(CDSA, lch) & 0xFFFF0000);
-
-	return offset;
-}
-EXPORT_SYMBOL(omap_get_dma_dst_pos);
-
-int omap_get_dma_active_status(int lch)
-{
-	return (p->dma_read(CCR, lch) & OMAP_DMA_CCR_EN) != 0;
-}
-EXPORT_SYMBOL(omap_get_dma_active_status);
-
-int omap_dma_running(void)
-{
-	int lch;
-
-	if (dma_omap1())
-		if (omap_lcd_dma_running())
-			return 1;
-
-	for (lch = 0; lch < dma_chan_count; lch++)
-		if (p->dma_read(CCR, lch) & OMAP_DMA_CCR_EN)
-			return 1;
-
-	return 0;
-}
-
-/*----------------------------------------------------------------------------*/
-
-#ifdef CONFIG_ARCH_OMAP1
-
-static int omap1_dma_handle_ch(int ch)
-{
-	u32 csr;
-
-	if (enable_1510_mode && ch >= 6) {
-		csr = dma_chan[ch].saved_csr;
-		dma_chan[ch].saved_csr = 0;
-	} else
-		csr = p->dma_read(CSR, ch);
-	if (enable_1510_mode && ch <= 2 && (csr >> 7) != 0) {
-		dma_chan[ch + 6].saved_csr = csr >> 7;
-		csr &= 0x7f;
-	}
-	if ((csr & 0x3f) == 0)
-		return 0;
-	if (unlikely(dma_chan[ch].dev_id == -1)) {
-		pr_warn("Spurious interrupt from DMA channel %d (CSR %04x)\n",
-			ch, csr);
-		return 0;
-	}
-	if (unlikely(csr & OMAP1_DMA_TOUT_IRQ))
-		pr_warn("DMA timeout with device %d\n", dma_chan[ch].dev_id);
-	if (unlikely(csr & OMAP_DMA_DROP_IRQ))
-		pr_warn("DMA synchronization event drop occurred with device %d\n",
-			dma_chan[ch].dev_id);
-	if (likely(csr & OMAP_DMA_BLOCK_IRQ))
-		dma_chan[ch].flags &= ~OMAP_DMA_ACTIVE;
-	if (likely(dma_chan[ch].callback != NULL))
-		dma_chan[ch].callback(ch, csr, dma_chan[ch].data);
-
-	return 1;
-}
-
-static irqreturn_t omap1_dma_irq_handler(int irq, void *dev_id)
-{
-	int ch = ((int) dev_id) - 1;
-	int handled = 0;
-
-	for (;;) {
-		int handled_now = 0;
-
-		handled_now += omap1_dma_handle_ch(ch);
-		if (enable_1510_mode && dma_chan[ch + 6].saved_csr)
-			handled_now += omap1_dma_handle_ch(ch + 6);
-		if (!handled_now)
-			break;
-		handled += handled_now;
-	}
-
-	return handled ? IRQ_HANDLED : IRQ_NONE;
-}
-
-#else
-#define omap1_dma_irq_handler	NULL
-#endif
-
-struct omap_system_dma_plat_info *omap_get_plat_info(void)
-{
-	return p;
-}
-EXPORT_SYMBOL_GPL(omap_get_plat_info);
-
-static int omap_system_dma_probe(struct platform_device *pdev)
-{
-	int ch, ret = 0;
-	int dma_irq;
-	char irq_name[4];
-
-	p = pdev->dev.platform_data;
-	if (!p) {
-		dev_err(&pdev->dev,
-			"%s: System DMA initialized without platform data\n",
-			__func__);
-		return -EINVAL;
-	}
-
-	d			= p->dma_attr;
-	errata			= p->errata;
-
-	if ((d->dev_caps & RESERVE_CHANNEL) && omap_dma_reserve_channels
-			&& (omap_dma_reserve_channels < d->lch_count))
-		d->lch_count	= omap_dma_reserve_channels;
-
-	dma_lch_count		= d->lch_count;
-	dma_chan_count		= dma_lch_count;
-	enable_1510_mode	= d->dev_caps & ENABLE_1510_MODE;
-
-	dma_chan = devm_kcalloc(&pdev->dev, dma_lch_count,
-				sizeof(*dma_chan), GFP_KERNEL);
-	if (!dma_chan)
-		return -ENOMEM;
-
-	for (ch = 0; ch < dma_chan_count; ch++) {
-		omap_clear_dma(ch);
-
-		dma_chan[ch].dev_id = -1;
-		dma_chan[ch].next_lch = -1;
-
-		if (ch >= 6 && enable_1510_mode)
-			continue;
-
-		if (dma_omap1()) {
-			/*
-			 * request_irq() doesn't like dev_id (ie. ch) being
-			 * zero, so we have to kludge around this.
-			 */
-			sprintf(&irq_name[0], "%d", ch);
-			dma_irq = platform_get_irq_byname(pdev, irq_name);
-
-			if (dma_irq < 0) {
-				ret = dma_irq;
-				goto exit_dma_irq_fail;
-			}
-
-			/* INT_DMA_LCD is handled in lcd_dma.c */
-			if (dma_irq == INT_DMA_LCD)
-				continue;
-
-			ret = request_irq(dma_irq,
-					omap1_dma_irq_handler, 0, "DMA",
-					(void *) (ch + 1));
-			if (ret != 0)
-				goto exit_dma_irq_fail;
-		}
-	}
-
-	/* reserve dma channels 0 and 1 in high security devices on 34xx */
-	if (d->dev_caps & HS_CHANNELS_RESERVED) {
-		pr_info("Reserving DMA channels 0 and 1 for HS ROM code\n");
-		dma_chan[0].dev_id = 0;
-		dma_chan[1].dev_id = 1;
-	}
-	p->show_dma_caps();
-	return 0;
-
-exit_dma_irq_fail:
-	return ret;
-}
-
-static int omap_system_dma_remove(struct platform_device *pdev)
-{
-	int dma_irq, irq_rel = 0;
-
-	if (dma_omap2plus())
-		return 0;
-
-	for ( ; irq_rel < dma_chan_count; irq_rel++) {
-		dma_irq = platform_get_irq(pdev, irq_rel);
-		free_irq(dma_irq, (void *)(irq_rel + 1));
-	}
-
-	return 0;
-}
-
-static struct platform_driver omap_system_dma_driver = {
-	.probe		= omap_system_dma_probe,
-	.remove		= omap_system_dma_remove,
-	.driver		= {
-		.name	= "omap_dma_system"
-	},
-};
-
-static int __init omap_system_dma_init(void)
-{
-	return platform_driver_register(&omap_system_dma_driver);
-}
-arch_initcall(omap_system_dma_init);
-
-static void __exit omap_system_dma_exit(void)
-{
-	platform_driver_unregister(&omap_system_dma_driver);
-}
-
-MODULE_DESCRIPTION("OMAP SYSTEM DMA DRIVER");
-MODULE_LICENSE("GPL");
-MODULE_AUTHOR("Texas Instruments Inc");
-
-/*
- * Reserve the omap SDMA channels using cmdline bootarg
- * "omap_dma_reserve_ch=". The valid range is 1 to 32
- */
-static int __init omap_dma_cmdline_reserve_ch(char *str)
-{
-	if (get_option(&str, &omap_dma_reserve_channels) != 1)
-		omap_dma_reserve_channels = 0;
-	return 1;
-}
-
-__setup("omap_dma_reserve_ch=", omap_dma_cmdline_reserve_ch);
-
-
diff --git a/arch/arm/plat-omap/include/plat/counter-32k.h b/arch/arm/plat-omap/include/plat/counter-32k.h
deleted file mode 100644
index da000d482ff2..000000000000
--- a/arch/arm/plat-omap/include/plat/counter-32k.h
+++ /dev/null
@@ -1 +0,0 @@
-int omap_init_clocksource_32k(void __iomem *vbase);
diff --git a/arch/arm/plat-omap/include/plat/cpu.h b/arch/arm/plat-omap/include/plat/cpu.h
deleted file mode 100644
index 36f4c352cc66..000000000000
--- a/arch/arm/plat-omap/include/plat/cpu.h
+++ /dev/null
@@ -1,21 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-or-later */
-/*
- * OMAP cpu type detection
- *
- * Copyright (C) 2004, 2008 Nokia Corporation
- *
- * Copyright (C) 2009-11 Texas Instruments.
- *
- * Written by Tony Lindgren <tony.lindgren@nokia.com>
- *
- * Added OMAP4/5 specific defines - Santosh Shilimkar<santosh.shilimkar@ti.com>
- */
-
-#ifndef __ASM_ARCH_OMAP_CPU_H
-#define __ASM_ARCH_OMAP_CPU_H
-
-#ifdef CONFIG_ARCH_OMAP1
-#include <mach/soc.h>
-#endif
-
-#endif
diff --git a/arch/arm/plat-omap/include/plat/sram.h b/arch/arm/plat-omap/include/plat/sram.h
deleted file mode 100644
index 30a07730807a..000000000000
--- a/arch/arm/plat-omap/include/plat/sram.h
+++ /dev/null
@@ -1,8 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-int omap_sram_init(void);
-
-void omap_map_sram(unsigned long start, unsigned long size,
-			unsigned long skip, int cached);
-void omap_sram_reset(void);
-
-extern void *omap_sram_push(void *funcp, unsigned long size);
diff --git a/arch/arm/plat-omap/sram.c b/arch/arm/plat-omap/sram.c
deleted file mode 100644
index 0f1eacad7fe3..000000000000
--- a/arch/arm/plat-omap/sram.c
+++ /dev/null
@@ -1,129 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * linux/arch/arm/plat-omap/sram.c
- *
- * OMAP SRAM detection and management
- *
- * Copyright (C) 2005 Nokia Corporation
- * Written by Tony Lindgren <tony@atomide.com>
- *
- * Copyright (C) 2009-2012 Texas Instruments
- * Added OMAP4/5 support - Santosh Shilimkar <santosh.shilimkar@ti.com>
- */
-#undef DEBUG
-
-#include <linux/module.h>
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/io.h>
-
-#include <asm/fncpy.h>
-#include <asm/tlb.h>
-#include <asm/cacheflush.h>
-#include <asm/set_memory.h>
-
-#include <asm/mach/map.h>
-
-#include <plat/sram.h>
-
-#define ROUND_DOWN(value,boundary)	((value) & (~((boundary)-1)))
-
-static void __iomem *omap_sram_base;
-static unsigned long omap_sram_skip;
-static unsigned long omap_sram_size;
-static void __iomem *omap_sram_ceil;
-
-/*
- * Memory allocator for SRAM: calculates the new ceiling address
- * for pushing a function using the fncpy API.
- *
- * Note that fncpy requires the returned address to be aligned
- * to an 8-byte boundary.
- */
-static void *omap_sram_push_address(unsigned long size)
-{
-	unsigned long available, new_ceil = (unsigned long)omap_sram_ceil;
-
-	available = omap_sram_ceil - (omap_sram_base + omap_sram_skip);
-
-	if (size > available) {
-		pr_err("Not enough space in SRAM\n");
-		return NULL;
-	}
-
-	new_ceil -= size;
-	new_ceil = ROUND_DOWN(new_ceil, FNCPY_ALIGN);
-	omap_sram_ceil = IOMEM(new_ceil);
-
-	return (void *)omap_sram_ceil;
-}
-
-void *omap_sram_push(void *funcp, unsigned long size)
-{
-	void *sram;
-	unsigned long base;
-	int pages;
-	void *dst = NULL;
-
-	sram = omap_sram_push_address(size);
-	if (!sram)
-		return NULL;
-
-	base = (unsigned long)sram & PAGE_MASK;
-	pages = PAGE_ALIGN(size) / PAGE_SIZE;
-
-	set_memory_rw(base, pages);
-
-	dst = fncpy(sram, funcp, size);
-
-	set_memory_ro(base, pages);
-	set_memory_x(base, pages);
-
-	return dst;
-}
-
-/*
- * The SRAM context is lost during off-idle and stack
- * needs to be reset.
- */
-void omap_sram_reset(void)
-{
-	omap_sram_ceil = omap_sram_base + omap_sram_size;
-}
-
-/*
- * Note that we cannot use ioremap for SRAM, as clock init needs SRAM early.
- */
-void __init omap_map_sram(unsigned long start, unsigned long size,
-				 unsigned long skip, int cached)
-{
-	unsigned long base;
-	int pages;
-
-	if (size == 0)
-		return;
-
-	start = ROUND_DOWN(start, PAGE_SIZE);
-	omap_sram_size = size;
-	omap_sram_skip = skip;
-	omap_sram_base = __arm_ioremap_exec(start, size, cached);
-	if (!omap_sram_base) {
-		pr_err("SRAM: Could not map\n");
-		return;
-	}
-
-	omap_sram_reset();
-
-	/*
-	 * Looks like we need to preserve some bootloader code at the
-	 * beginning of SRAM for jumping to flash for reboot to work...
-	 */
-	memset_io(omap_sram_base + omap_sram_skip, 0,
-		  omap_sram_size - omap_sram_skip);
-
-	base = (unsigned long)omap_sram_base;
-	pages = PAGE_ALIGN(omap_sram_size) / PAGE_SIZE;
-
-	set_memory_ro(base, pages);
-	set_memory_x(base, pages);
-}
diff --git a/arch/arm/plat-orion/Makefile b/arch/arm/plat-orion/Makefile
index 4e3f25de13c1..830b0be038c6 100644
--- a/arch/arm/plat-orion/Makefile
+++ b/arch/arm/plat-orion/Makefile
@@ -2,7 +2,7 @@
 #
 # Makefile for the linux kernel.
 #
-ccflags-$(CONFIG_ARCH_MULTIPLATFORM) := -I$(srctree)/$(src)/include
+ccflags-y := -I$(srctree)/$(src)/include
 
 orion-gpio-$(CONFIG_GPIOLIB)      += gpio.o
 obj-$(CONFIG_PLAT_ORION_LEGACY)   += irq.o pcie.o time.o common.o mpp.o
diff --git a/arch/arm/plat-orion/gpio.c b/arch/arm/plat-orion/gpio.c
index 734f0be4f14a..3ef9ecdd6343 100644
--- a/arch/arm/plat-orion/gpio.c
+++ b/arch/arm/plat-orion/gpio.c
@@ -516,8 +516,7 @@ static void orion_gpio_mask_irq(struct irq_data *d)
 	irq_gc_unlock(gc);
 }
 
-void __init orion_gpio_init(struct device_node *np,
-			    int gpio_base, int ngpio,
+void __init orion_gpio_init(int gpio_base, int ngpio,
 			    void __iomem *base, int mask_offset,
 			    int secondary_irq_base,
 			    int irqs[4])
@@ -545,9 +544,6 @@ void __init orion_gpio_init(struct device_node *np,
 	ochip->chip.base = gpio_base;
 	ochip->chip.ngpio = ngpio;
 	ochip->chip.can_sleep = 0;
-#ifdef CONFIG_OF
-	ochip->chip.of_node = np;
-#endif
 	ochip->chip.dbg_show = orion_gpio_dbg_show;
 
 	spin_lock_init(&ochip->lock);
@@ -605,7 +601,7 @@ void __init orion_gpio_init(struct device_node *np,
 			       IRQ_NOREQUEST, IRQ_LEVEL | IRQ_NOPROBE);
 
 	/* Setup irq domain on top of the generic chip. */
-	ochip->domain = irq_domain_add_legacy(np,
+	ochip->domain = irq_domain_add_legacy(NULL,
 					      ochip->chip.ngpio,
 					      ochip->secondary_irq_base,
 					      ochip->secondary_irq_base,
diff --git a/arch/arm/plat-orion/include/plat/orion-gpio.h b/arch/arm/plat-orion/include/plat/orion-gpio.h
index e856b073a9c8..25a2963e0e0f 100644
--- a/arch/arm/plat-orion/include/plat/orion-gpio.h
+++ b/arch/arm/plat-orion/include/plat/orion-gpio.h
@@ -30,8 +30,7 @@ int orion_gpio_led_blink_set(struct gpio_desc *desc, int state,
 void orion_gpio_set_valid(unsigned pin, int mode);
 
 /* Initialize gpiolib. */
-void __init orion_gpio_init(struct device_node *np,
-			    int gpio_base, int ngpio,
+void __init orion_gpio_init(int gpio_base, int ngpio,
 			    void __iomem *base, int mask_offset,
 			    int secondary_irq_base,
 			    int irq[4]);
diff --git a/arch/arm/plat-pxa/Kconfig b/arch/arm/plat-pxa/Kconfig
deleted file mode 100644
index 6f7a0a39c2b9..000000000000
--- a/arch/arm/plat-pxa/Kconfig
+++ /dev/null
@@ -1,9 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0-only
-if PLAT_PXA
-
-config PXA_SSP
-	tristate
-	help
-	  Enable support for PXA2xx SSP ports
-
-endif
diff --git a/arch/arm/plat-pxa/Makefile b/arch/arm/plat-pxa/Makefile
deleted file mode 100644
index 349ea0af8450..000000000000
--- a/arch/arm/plat-pxa/Makefile
+++ /dev/null
@@ -1,10 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0-only
-#
-# Makefile for code common across different PXA processor families
-#
-ccflags-$(CONFIG_ARCH_MMP) := -I$(srctree)/$(src)/include
-
-obj-$(CONFIG_PXA3xx)		+= mfp.o
-obj-$(CONFIG_ARCH_MMP)		+= mfp.o
-
-obj-$(CONFIG_PXA_SSP)		+= ssp.o
diff --git a/arch/arm/plat-pxa/include/plat/mfp.h b/arch/arm/plat-pxa/include/plat/mfp.h
deleted file mode 100644
index 3accaa9ee781..000000000000
--- a/arch/arm/plat-pxa/include/plat/mfp.h
+++ /dev/null
@@ -1,472 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-only */
-/*
- * arch/arm/plat-pxa/include/plat/mfp.h
- *
- *   Common Multi-Function Pin Definitions
- *
- * Copyright (C) 2007 Marvell International Ltd.
- *
- * 2007-8-21: eric miao <eric.miao@marvell.com>
- *            initial version
- */
-
-#ifndef __ASM_PLAT_MFP_H
-#define __ASM_PLAT_MFP_H
-
-#define mfp_to_gpio(m)	((m) % 256)
-
-/* list of all the configurable MFP pins */
-enum {
-	MFP_PIN_INVALID = -1,
-
-	MFP_PIN_GPIO0 = 0,
-	MFP_PIN_GPIO1,
-	MFP_PIN_GPIO2,
-	MFP_PIN_GPIO3,
-	MFP_PIN_GPIO4,
-	MFP_PIN_GPIO5,
-	MFP_PIN_GPIO6,
-	MFP_PIN_GPIO7,
-	MFP_PIN_GPIO8,
-	MFP_PIN_GPIO9,
-	MFP_PIN_GPIO10,
-	MFP_PIN_GPIO11,
-	MFP_PIN_GPIO12,
-	MFP_PIN_GPIO13,
-	MFP_PIN_GPIO14,
-	MFP_PIN_GPIO15,
-	MFP_PIN_GPIO16,
-	MFP_PIN_GPIO17,
-	MFP_PIN_GPIO18,
-	MFP_PIN_GPIO19,
-	MFP_PIN_GPIO20,
-	MFP_PIN_GPIO21,
-	MFP_PIN_GPIO22,
-	MFP_PIN_GPIO23,
-	MFP_PIN_GPIO24,
-	MFP_PIN_GPIO25,
-	MFP_PIN_GPIO26,
-	MFP_PIN_GPIO27,
-	MFP_PIN_GPIO28,
-	MFP_PIN_GPIO29,
-	MFP_PIN_GPIO30,
-	MFP_PIN_GPIO31,
-	MFP_PIN_GPIO32,
-	MFP_PIN_GPIO33,
-	MFP_PIN_GPIO34,
-	MFP_PIN_GPIO35,
-	MFP_PIN_GPIO36,
-	MFP_PIN_GPIO37,
-	MFP_PIN_GPIO38,
-	MFP_PIN_GPIO39,
-	MFP_PIN_GPIO40,
-	MFP_PIN_GPIO41,
-	MFP_PIN_GPIO42,
-	MFP_PIN_GPIO43,
-	MFP_PIN_GPIO44,
-	MFP_PIN_GPIO45,
-	MFP_PIN_GPIO46,
-	MFP_PIN_GPIO47,
-	MFP_PIN_GPIO48,
-	MFP_PIN_GPIO49,
-	MFP_PIN_GPIO50,
-	MFP_PIN_GPIO51,
-	MFP_PIN_GPIO52,
-	MFP_PIN_GPIO53,
-	MFP_PIN_GPIO54,
-	MFP_PIN_GPIO55,
-	MFP_PIN_GPIO56,
-	MFP_PIN_GPIO57,
-	MFP_PIN_GPIO58,
-	MFP_PIN_GPIO59,
-	MFP_PIN_GPIO60,
-	MFP_PIN_GPIO61,
-	MFP_PIN_GPIO62,
-	MFP_PIN_GPIO63,
-	MFP_PIN_GPIO64,
-	MFP_PIN_GPIO65,
-	MFP_PIN_GPIO66,
-	MFP_PIN_GPIO67,
-	MFP_PIN_GPIO68,
-	MFP_PIN_GPIO69,
-	MFP_PIN_GPIO70,
-	MFP_PIN_GPIO71,
-	MFP_PIN_GPIO72,
-	MFP_PIN_GPIO73,
-	MFP_PIN_GPIO74,
-	MFP_PIN_GPIO75,
-	MFP_PIN_GPIO76,
-	MFP_PIN_GPIO77,
-	MFP_PIN_GPIO78,
-	MFP_PIN_GPIO79,
-	MFP_PIN_GPIO80,
-	MFP_PIN_GPIO81,
-	MFP_PIN_GPIO82,
-	MFP_PIN_GPIO83,
-	MFP_PIN_GPIO84,
-	MFP_PIN_GPIO85,
-	MFP_PIN_GPIO86,
-	MFP_PIN_GPIO87,
-	MFP_PIN_GPIO88,
-	MFP_PIN_GPIO89,
-	MFP_PIN_GPIO90,
-	MFP_PIN_GPIO91,
-	MFP_PIN_GPIO92,
-	MFP_PIN_GPIO93,
-	MFP_PIN_GPIO94,
-	MFP_PIN_GPIO95,
-	MFP_PIN_GPIO96,
-	MFP_PIN_GPIO97,
-	MFP_PIN_GPIO98,
-	MFP_PIN_GPIO99,
-	MFP_PIN_GPIO100,
-	MFP_PIN_GPIO101,
-	MFP_PIN_GPIO102,
-	MFP_PIN_GPIO103,
-	MFP_PIN_GPIO104,
-	MFP_PIN_GPIO105,
-	MFP_PIN_GPIO106,
-	MFP_PIN_GPIO107,
-	MFP_PIN_GPIO108,
-	MFP_PIN_GPIO109,
-	MFP_PIN_GPIO110,
-	MFP_PIN_GPIO111,
-	MFP_PIN_GPIO112,
-	MFP_PIN_GPIO113,
-	MFP_PIN_GPIO114,
-	MFP_PIN_GPIO115,
-	MFP_PIN_GPIO116,
-	MFP_PIN_GPIO117,
-	MFP_PIN_GPIO118,
-	MFP_PIN_GPIO119,
-	MFP_PIN_GPIO120,
-	MFP_PIN_GPIO121,
-	MFP_PIN_GPIO122,
-	MFP_PIN_GPIO123,
-	MFP_PIN_GPIO124,
-	MFP_PIN_GPIO125,
-	MFP_PIN_GPIO126,
-	MFP_PIN_GPIO127,
-
-	MFP_PIN_GPIO128,
-	MFP_PIN_GPIO129,
-	MFP_PIN_GPIO130,
-	MFP_PIN_GPIO131,
-	MFP_PIN_GPIO132,
-	MFP_PIN_GPIO133,
-	MFP_PIN_GPIO134,
-	MFP_PIN_GPIO135,
-	MFP_PIN_GPIO136,
-	MFP_PIN_GPIO137,
-	MFP_PIN_GPIO138,
-	MFP_PIN_GPIO139,
-	MFP_PIN_GPIO140,
-	MFP_PIN_GPIO141,
-	MFP_PIN_GPIO142,
-	MFP_PIN_GPIO143,
-	MFP_PIN_GPIO144,
-	MFP_PIN_GPIO145,
-	MFP_PIN_GPIO146,
-	MFP_PIN_GPIO147,
-	MFP_PIN_GPIO148,
-	MFP_PIN_GPIO149,
-	MFP_PIN_GPIO150,
-	MFP_PIN_GPIO151,
-	MFP_PIN_GPIO152,
-	MFP_PIN_GPIO153,
-	MFP_PIN_GPIO154,
-	MFP_PIN_GPIO155,
-	MFP_PIN_GPIO156,
-	MFP_PIN_GPIO157,
-	MFP_PIN_GPIO158,
-	MFP_PIN_GPIO159,
-	MFP_PIN_GPIO160,
-	MFP_PIN_GPIO161,
-	MFP_PIN_GPIO162,
-	MFP_PIN_GPIO163,
-	MFP_PIN_GPIO164,
-	MFP_PIN_GPIO165,
-	MFP_PIN_GPIO166,
-	MFP_PIN_GPIO167,
-	MFP_PIN_GPIO168,
-	MFP_PIN_GPIO169,
-	MFP_PIN_GPIO170,
-	MFP_PIN_GPIO171,
-	MFP_PIN_GPIO172,
-	MFP_PIN_GPIO173,
-	MFP_PIN_GPIO174,
-	MFP_PIN_GPIO175,
-	MFP_PIN_GPIO176,
-	MFP_PIN_GPIO177,
-	MFP_PIN_GPIO178,
-	MFP_PIN_GPIO179,
-	MFP_PIN_GPIO180,
-	MFP_PIN_GPIO181,
-	MFP_PIN_GPIO182,
-	MFP_PIN_GPIO183,
-	MFP_PIN_GPIO184,
-	MFP_PIN_GPIO185,
-	MFP_PIN_GPIO186,
-	MFP_PIN_GPIO187,
-	MFP_PIN_GPIO188,
-	MFP_PIN_GPIO189,
-	MFP_PIN_GPIO190,
-	MFP_PIN_GPIO191,
-
-	MFP_PIN_GPIO255 = 255,
-
-	MFP_PIN_GPIO0_2,
-	MFP_PIN_GPIO1_2,
-	MFP_PIN_GPIO2_2,
-	MFP_PIN_GPIO3_2,
-	MFP_PIN_GPIO4_2,
-	MFP_PIN_GPIO5_2,
-	MFP_PIN_GPIO6_2,
-	MFP_PIN_GPIO7_2,
-	MFP_PIN_GPIO8_2,
-	MFP_PIN_GPIO9_2,
-	MFP_PIN_GPIO10_2,
-	MFP_PIN_GPIO11_2,
-	MFP_PIN_GPIO12_2,
-	MFP_PIN_GPIO13_2,
-	MFP_PIN_GPIO14_2,
-	MFP_PIN_GPIO15_2,
-	MFP_PIN_GPIO16_2,
-	MFP_PIN_GPIO17_2,
-
-	MFP_PIN_ULPI_STP,
-	MFP_PIN_ULPI_NXT,
-	MFP_PIN_ULPI_DIR,
-
-	MFP_PIN_nXCVREN,
-	MFP_PIN_DF_CLE_nOE,
-	MFP_PIN_DF_nADV1_ALE,
-	MFP_PIN_DF_SCLK_E,
-	MFP_PIN_DF_SCLK_S,
-	MFP_PIN_nBE0,
-	MFP_PIN_nBE1,
-	MFP_PIN_DF_nADV2_ALE,
-	MFP_PIN_DF_INT_RnB,
-	MFP_PIN_DF_nCS0,
-	MFP_PIN_DF_nCS1,
-	MFP_PIN_nLUA,
-	MFP_PIN_nLLA,
-	MFP_PIN_DF_nWE,
-	MFP_PIN_DF_ALE_nWE,
-	MFP_PIN_DF_nRE_nOE,
-	MFP_PIN_DF_ADDR0,
-	MFP_PIN_DF_ADDR1,
-	MFP_PIN_DF_ADDR2,
-	MFP_PIN_DF_ADDR3,
-	MFP_PIN_DF_IO0,
-	MFP_PIN_DF_IO1,
-	MFP_PIN_DF_IO2,
-	MFP_PIN_DF_IO3,
-	MFP_PIN_DF_IO4,
-	MFP_PIN_DF_IO5,
-	MFP_PIN_DF_IO6,
-	MFP_PIN_DF_IO7,
-	MFP_PIN_DF_IO8,
-	MFP_PIN_DF_IO9,
-	MFP_PIN_DF_IO10,
-	MFP_PIN_DF_IO11,
-	MFP_PIN_DF_IO12,
-	MFP_PIN_DF_IO13,
-	MFP_PIN_DF_IO14,
-	MFP_PIN_DF_IO15,
-	MFP_PIN_DF_nCS0_SM_nCS2,
-	MFP_PIN_DF_nCS1_SM_nCS3,
-	MFP_PIN_SM_nCS0,
-	MFP_PIN_SM_nCS1,
-	MFP_PIN_DF_WEn,
-	MFP_PIN_DF_REn,
-	MFP_PIN_DF_CLE_SM_OEn,
-	MFP_PIN_DF_ALE_SM_WEn,
-	MFP_PIN_DF_RDY0,
-	MFP_PIN_DF_RDY1,
-
-	MFP_PIN_SM_SCLK,
-	MFP_PIN_SM_BE0,
-	MFP_PIN_SM_BE1,
-	MFP_PIN_SM_ADV,
-	MFP_PIN_SM_ADVMUX,
-	MFP_PIN_SM_RDY,
-
-	MFP_PIN_MMC1_DAT7,
-	MFP_PIN_MMC1_DAT6,
-	MFP_PIN_MMC1_DAT5,
-	MFP_PIN_MMC1_DAT4,
-	MFP_PIN_MMC1_DAT3,
-	MFP_PIN_MMC1_DAT2,
-	MFP_PIN_MMC1_DAT1,
-	MFP_PIN_MMC1_DAT0,
-	MFP_PIN_MMC1_CMD,
-	MFP_PIN_MMC1_CLK,
-	MFP_PIN_MMC1_CD,
-	MFP_PIN_MMC1_WP,
-
-	/* additional pins on PXA930 */
-	MFP_PIN_GSIM_UIO,
-	MFP_PIN_GSIM_UCLK,
-	MFP_PIN_GSIM_UDET,
-	MFP_PIN_GSIM_nURST,
-	MFP_PIN_PMIC_INT,
-	MFP_PIN_RDY,
-
-	/* additional pins on MMP2 */
-	MFP_PIN_TWSI1_SCL,
-	MFP_PIN_TWSI1_SDA,
-	MFP_PIN_TWSI4_SCL,
-	MFP_PIN_TWSI4_SDA,
-	MFP_PIN_CLK_REQ,
-
-	MFP_PIN_MAX,
-};
-
-/*
- * a possible MFP configuration is represented by a 32-bit integer
- *
- * bit  0.. 9 - MFP Pin Number (1024 Pins Maximum)
- * bit 10..12 - Alternate Function Selection
- * bit 13..15 - Drive Strength
- * bit 16..18 - Low Power Mode State
- * bit 19..20 - Low Power Mode Edge Detection
- * bit 21..22 - Run Mode Pull State
- *
- * to facilitate the definition, the following macros are provided
- *
- * MFP_CFG_DEFAULT - default MFP configuration value, with
- * 		  alternate function = 0,
- * 		  drive strength = fast 3mA (MFP_DS03X)
- * 		  low power mode = default
- * 		  edge detection = none
- *
- * MFP_CFG	- default MFPR value with alternate function
- * MFP_CFG_DRV	- default MFPR value with alternate function and
- * 		  pin drive strength
- * MFP_CFG_LPM	- default MFPR value with alternate function and
- * 		  low power mode
- * MFP_CFG_X	- default MFPR value with alternate function,
- * 		  pin drive strength and low power mode
- */
-
-typedef unsigned long mfp_cfg_t;
-
-#define MFP_PIN(x)		((x) & 0x3ff)
-
-#define MFP_AF0			(0x0 << 10)
-#define MFP_AF1			(0x1 << 10)
-#define MFP_AF2			(0x2 << 10)
-#define MFP_AF3			(0x3 << 10)
-#define MFP_AF4			(0x4 << 10)
-#define MFP_AF5			(0x5 << 10)
-#define MFP_AF6			(0x6 << 10)
-#define MFP_AF7			(0x7 << 10)
-#define MFP_AF_MASK		(0x7 << 10)
-#define MFP_AF(x)		(((x) >> 10) & 0x7)
-
-#define MFP_DS01X		(0x0 << 13)
-#define MFP_DS02X		(0x1 << 13)
-#define MFP_DS03X		(0x2 << 13)
-#define MFP_DS04X		(0x3 << 13)
-#define MFP_DS06X		(0x4 << 13)
-#define MFP_DS08X		(0x5 << 13)
-#define MFP_DS10X		(0x6 << 13)
-#define MFP_DS13X		(0x7 << 13)
-#define MFP_DS_MASK		(0x7 << 13)
-#define MFP_DS(x)		(((x) >> 13) & 0x7)
-
-#define MFP_LPM_DEFAULT		(0x0 << 16)
-#define MFP_LPM_DRIVE_LOW	(0x1 << 16)
-#define MFP_LPM_DRIVE_HIGH	(0x2 << 16)
-#define MFP_LPM_PULL_LOW	(0x3 << 16)
-#define MFP_LPM_PULL_HIGH	(0x4 << 16)
-#define MFP_LPM_FLOAT		(0x5 << 16)
-#define MFP_LPM_INPUT		(0x6 << 16)
-#define MFP_LPM_STATE_MASK	(0x7 << 16)
-#define MFP_LPM_STATE(x)	(((x) >> 16) & 0x7)
-
-#define MFP_LPM_EDGE_NONE	(0x0 << 19)
-#define MFP_LPM_EDGE_RISE	(0x1 << 19)
-#define MFP_LPM_EDGE_FALL	(0x2 << 19)
-#define MFP_LPM_EDGE_BOTH	(0x3 << 19)
-#define MFP_LPM_EDGE_MASK	(0x3 << 19)
-#define MFP_LPM_EDGE(x)		(((x) >> 19) & 0x3)
-
-#define MFP_PULL_NONE		(0x0 << 21)
-#define MFP_PULL_LOW		(0x1 << 21)
-#define MFP_PULL_HIGH		(0x2 << 21)
-#define MFP_PULL_BOTH		(0x3 << 21)
-#define MFP_PULL_FLOAT		(0x4 << 21)
-#define MFP_PULL_MASK		(0x7 << 21)
-#define MFP_PULL(x)		(((x) >> 21) & 0x7)
-
-#define MFP_CFG_DEFAULT		(MFP_AF0 | MFP_DS03X | MFP_LPM_DEFAULT |\
-				 MFP_LPM_EDGE_NONE | MFP_PULL_NONE)
-
-#define MFP_CFG(pin, af)		\
-	((MFP_CFG_DEFAULT & ~MFP_AF_MASK) |\
-	 (MFP_PIN(MFP_PIN_##pin) | MFP_##af))
-
-#define MFP_CFG_DRV(pin, af, drv)	\
-	((MFP_CFG_DEFAULT & ~(MFP_AF_MASK | MFP_DS_MASK)) |\
-	 (MFP_PIN(MFP_PIN_##pin) | MFP_##af | MFP_##drv))
-
-#define MFP_CFG_LPM(pin, af, lpm)	\
-	((MFP_CFG_DEFAULT & ~(MFP_AF_MASK | MFP_LPM_STATE_MASK)) |\
-	 (MFP_PIN(MFP_PIN_##pin) | MFP_##af | MFP_LPM_##lpm))
-
-#define MFP_CFG_X(pin, af, drv, lpm)	\
-	((MFP_CFG_DEFAULT & ~(MFP_AF_MASK | MFP_DS_MASK | MFP_LPM_STATE_MASK)) |\
-	 (MFP_PIN(MFP_PIN_##pin) | MFP_##af | MFP_##drv | MFP_LPM_##lpm))
-
-#if defined(CONFIG_PXA3xx) || defined(CONFIG_ARCH_MMP)
-/*
- * each MFP pin will have a MFPR register, since the offset of the
- * register varies between processors, the processor specific code
- * should initialize the pin offsets by mfp_init()
- *
- * mfp_init_base() - accepts a virtual base for all MFPR registers and
- * initialize the MFP table to a default state
- *
- * mfp_init_addr() - accepts a table of "mfp_addr_map" structure, which
- * represents a range of MFP pins from "start" to "end", with the offset
- * beginning at "offset", to define a single pin, let "end" = -1.
- *
- * use
- *
- * MFP_ADDR_X() to define a range of pins
- * MFP_ADDR()   to define a single pin
- * MFP_ADDR_END to signal the end of pin offset definitions
- */
-struct mfp_addr_map {
-	unsigned int	start;
-	unsigned int	end;
-	unsigned long	offset;
-};
-
-#define MFP_ADDR_X(start, end, offset) \
-	{ MFP_PIN_##start, MFP_PIN_##end, offset }
-
-#define MFP_ADDR(pin, offset) \
-	{ MFP_PIN_##pin, -1, offset }
-
-#define MFP_ADDR_END	{ MFP_PIN_INVALID, 0 }
-
-void __init mfp_init_base(void __iomem *mfpr_base);
-void __init mfp_init_addr(struct mfp_addr_map *map);
-
-/*
- * mfp_{read, write}()	- for direct read/write access to the MFPR register
- * mfp_config()		- for configuring a group of MFPR registers
- * mfp_config_lpm()	- configuring all low power MFPR registers for suspend
- * mfp_config_run()	- configuring all run time  MFPR registers after resume
- */
-unsigned long mfp_read(int mfp);
-void mfp_write(int mfp, unsigned long mfpr_val);
-void mfp_config(unsigned long *mfp_cfgs, int num);
-void mfp_config_run(void);
-void mfp_config_lpm(void);
-#endif /* CONFIG_PXA3xx || CONFIG_ARCH_MMP */
-
-#endif /* __ASM_PLAT_MFP_H */
diff --git a/arch/arm/plat-versatile/Makefile b/arch/arm/plat-versatile/Makefile
deleted file mode 100644
index 5de44a57c4de..000000000000
--- a/arch/arm/plat-versatile/Makefile
+++ /dev/null
@@ -1,5 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0-only
-ccflags-$(CONFIG_ARCH_MULTIPLATFORM) := -I$(srctree)/$(src)/include
-
-obj-$(CONFIG_SMP) += headsmp.o platsmp.o
-obj-$(CONFIG_HOTPLUG_CPU)		+= hotplug.o
diff --git a/arch/arm/plat-versatile/platsmp.c b/arch/arm/plat-versatile/platsmp.c
deleted file mode 100644
index 3567296cec2a..000000000000
--- a/arch/arm/plat-versatile/platsmp.c
+++ /dev/null
@@ -1,109 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- *  linux/arch/arm/plat-versatile/platsmp.c
- *
- *  Copyright (C) 2002 ARM Ltd.
- *  All Rights Reserved
- *
- * This code is specific to the hardware found on ARM Realview and
- * Versatile Express platforms where the CPUs are unable to be individually
- * woken, and where there is no way to hot-unplug CPUs.  Real platforms
- * should not copy this code.
- */
-#include <linux/init.h>
-#include <linux/errno.h>
-#include <linux/delay.h>
-#include <linux/device.h>
-#include <linux/jiffies.h>
-#include <linux/smp.h>
-
-#include <asm/cacheflush.h>
-#include <asm/smp_plat.h>
-
-#include <plat/platsmp.h>
-
-/*
- * versatile_cpu_release controls the release of CPUs from the holding
- * pen in headsmp.S, which exists because we are not always able to
- * control the release of individual CPUs from the board firmware.
- * Production platforms do not need this.
- */
-volatile int versatile_cpu_release = -1;
-
-/*
- * Write versatile_cpu_release in a way that is guaranteed to be visible to
- * all observers, irrespective of whether they're taking part in coherency
- * or not.  This is necessary for the hotplug code to work reliably.
- */
-static void versatile_write_cpu_release(int val)
-{
-	versatile_cpu_release = val;
-	smp_wmb();
-	sync_cache_w(&versatile_cpu_release);
-}
-
-/*
- * versatile_lock exists to avoid running the loops_per_jiffy delay loop
- * calibrations on the secondary CPU while the requesting CPU is using
- * the limited-bandwidth bus - which affects the calibration value.
- * Production platforms do not need this.
- */
-static DEFINE_RAW_SPINLOCK(versatile_lock);
-
-void versatile_secondary_init(unsigned int cpu)
-{
-	/*
-	 * let the primary processor know we're out of the
-	 * pen, then head off into the C entry point
-	 */
-	versatile_write_cpu_release(-1);
-
-	/*
-	 * Synchronise with the boot thread.
-	 */
-	raw_spin_lock(&versatile_lock);
-	raw_spin_unlock(&versatile_lock);
-}
-
-int versatile_boot_secondary(unsigned int cpu, struct task_struct *idle)
-{
-	unsigned long timeout;
-
-	/*
-	 * Set synchronisation state between this boot processor
-	 * and the secondary one
-	 */
-	raw_spin_lock(&versatile_lock);
-
-	/*
-	 * This is really belt and braces; we hold unintended secondary
-	 * CPUs in the holding pen until we're ready for them.  However,
-	 * since we haven't sent them a soft interrupt, they shouldn't
-	 * be there.
-	 */
-	versatile_write_cpu_release(cpu_logical_map(cpu));
-
-	/*
-	 * Send the secondary CPU a soft interrupt, thereby causing
-	 * the boot monitor to read the system wide flags register,
-	 * and branch to the address found there.
-	 */
-	arch_send_wakeup_ipi_mask(cpumask_of(cpu));
-
-	timeout = jiffies + (1 * HZ);
-	while (time_before(jiffies, timeout)) {
-		smp_rmb();
-		if (versatile_cpu_release == -1)
-			break;
-
-		udelay(10);
-	}
-
-	/*
-	 * now the secondary core is starting up let it run its
-	 * calibrations, then wait for it to finish
-	 */
-	raw_spin_unlock(&versatile_lock);
-
-	return versatile_cpu_release != -1 ? -ENOSYS : 0;
-}
diff --git a/arch/arm/probes/decode.h b/arch/arm/probes/decode.h
index 973173598992..facc889d05ee 100644
--- a/arch/arm/probes/decode.h
+++ b/arch/arm/probes/decode.h
@@ -14,6 +14,7 @@
 #include <linux/types.h>
 #include <linux/stddef.h>
 #include <asm/probes.h>
+#include <asm/ptrace.h>
 #include <asm/kprobes.h>
 
 void __init arm_probes_decode_init(void);
@@ -35,31 +36,6 @@ void __init find_str_pc_offset(void);
 #endif
 
 
-/*
- * Update ITSTATE after normal execution of an IT block instruction.
- *
- * The 8 IT state bits are split into two parts in CPSR:
- *	ITSTATE<1:0> are in CPSR<26:25>
- *	ITSTATE<7:2> are in CPSR<15:10>
- */
-static inline unsigned long it_advance(unsigned long cpsr)
-	{
-	if ((cpsr & 0x06000400) == 0) {
-		/* ITSTATE<2:0> == 0 means end of IT block, so clear IT state */
-		cpsr &= ~PSR_IT_MASK;
-	} else {
-		/* We need to shift left ITSTATE<4:0> */
-		const unsigned long mask = 0x06001c00;  /* Mask ITSTATE<4:0> */
-		unsigned long it = cpsr & mask;
-		it <<= 1;
-		it |= it >> (27 - 10);  /* Carry ITSTATE<2> to correct place */
-		it &= mask;
-		cpsr &= ~mask;
-		cpsr |= it;
-	}
-	return cpsr;
-}
-
 static inline void __kprobes bx_write_pc(long pcv, struct pt_regs *regs)
 {
 	long cpsr = regs->ARM_cpsr;
diff --git a/arch/arm/probes/kprobes/Makefile b/arch/arm/probes/kprobes/Makefile
index 14db56f49f0a..6159010dac4a 100644
--- a/arch/arm/probes/kprobes/Makefile
+++ b/arch/arm/probes/kprobes/Makefile
@@ -1,4 +1,7 @@
 # SPDX-License-Identifier: GPL-2.0
+KASAN_SANITIZE_actions-common.o := n
+KASAN_SANITIZE_actions-arm.o := n
+KASAN_SANITIZE_actions-thumb.o := n
 obj-$(CONFIG_KPROBES)		+= core.o actions-common.o checkers-common.o
 obj-$(CONFIG_ARM_KPROBES_TEST)	+= test-kprobes.o
 test-kprobes-objs		:= test-core.o
diff --git a/arch/arm/probes/kprobes/actions-common.c b/arch/arm/probes/kprobes/actions-common.c
index 836aebe596cd..79171344dbeb 100644
--- a/arch/arm/probes/kprobes/actions-common.c
+++ b/arch/arm/probes/kprobes/actions-common.c
@@ -84,7 +84,8 @@ emulate_generic_r0_12_noflags(probes_opcode_t insn,
 	register void *rfn asm("lr") = asi->insn_fn;
 
 	__asm__ __volatile__ (
-		"stmdb	sp!, {%[regs], r11}	\n\t"
+ARM(		"stmdb	sp!, {%[regs], r11}	\n\t"	)
+THUMB(		"stmdb	sp!, {%[regs], r7}	\n\t"	)
 		"ldmia	%[regs], {r0-r12}	\n\t"
 #if __LINUX_ARM_ARCH__ >= 6
 		"blx	%[fn]			\n\t"
@@ -96,10 +97,11 @@ emulate_generic_r0_12_noflags(probes_opcode_t insn,
 #endif
 		"ldr	lr, [sp], #4		\n\t" /* lr = regs */
 		"stmia	lr, {r0-r12}		\n\t"
-		"ldr	r11, [sp], #4		\n\t"
+ARM(		"ldr	r11, [sp], #4		\n\t"	)
+THUMB(		"ldr	r7, [sp], #4		\n\t"	)
 		: [regs] "=r" (rregs), [fn] "=r" (rfn)
 		: "0" (rregs), "1" (rfn)
-		: "r0", "r2", "r3", "r4", "r5", "r6", "r7",
+		: "r0", "r2", "r3", "r4", "r5", "r6", ARM("r7") THUMB("r11"),
 		  "r8", "r9", "r10", "r12", "memory", "cc"
 		);
 }
diff --git a/arch/arm/probes/kprobes/actions-thumb.c b/arch/arm/probes/kprobes/actions-thumb.c
index 7884fcb81c26..51624fc263fc 100644
--- a/arch/arm/probes/kprobes/actions-thumb.c
+++ b/arch/arm/probes/kprobes/actions-thumb.c
@@ -447,14 +447,16 @@ t16_emulate_loregs(probes_opcode_t insn,
 
 	__asm__ __volatile__ (
 		"msr	cpsr_fs, %[oldcpsr]	\n\t"
+		"mov	r11, r7			\n\t"
 		"ldmia	%[regs], {r0-r7}	\n\t"
 		"blx	%[fn]			\n\t"
 		"stmia	%[regs], {r0-r7}	\n\t"
+		"mov	r7, r11			\n\t"
 		"mrs	%[newcpsr], cpsr	\n\t"
 		: [newcpsr] "=r" (newcpsr)
 		: [oldcpsr] "r" (oldcpsr), [regs] "r" (regs),
 		  [fn] "r" (asi->insn_fn)
-		: "r0", "r1", "r2", "r3", "r4", "r5", "r6", "r7",
+		: "r0", "r1", "r2", "r3", "r4", "r5", "r6", "r11",
 		  "lr", "memory", "cc"
 		);
 
@@ -524,14 +526,16 @@ t16_emulate_push(probes_opcode_t insn,
 		struct arch_probes_insn *asi, struct pt_regs *regs)
 {
 	__asm__ __volatile__ (
+		"mov	r11, r7			\n\t"
 		"ldr	r9, [%[regs], #13*4]	\n\t"
 		"ldr	r8, [%[regs], #14*4]	\n\t"
 		"ldmia	%[regs], {r0-r7}	\n\t"
 		"blx	%[fn]			\n\t"
 		"str	r9, [%[regs], #13*4]	\n\t"
+		"mov	r7, r11			\n\t"
 		:
 		: [regs] "r" (regs), [fn] "r" (asi->insn_fn)
-		: "r0", "r1", "r2", "r3", "r4", "r5", "r6", "r7", "r8", "r9",
+		: "r0", "r1", "r2", "r3", "r4", "r5", "r6", "r8", "r9", "r11",
 		  "lr", "memory", "cc"
 		);
 }
@@ -558,14 +562,16 @@ t16_emulate_pop_nopc(probes_opcode_t insn,
 		struct arch_probes_insn *asi, struct pt_regs *regs)
 {
 	__asm__ __volatile__ (
+		"mov	r11, r7			\n\t"
 		"ldr	r9, [%[regs], #13*4]	\n\t"
 		"ldmia	%[regs], {r0-r7}	\n\t"
 		"blx	%[fn]			\n\t"
 		"stmia	%[regs], {r0-r7}	\n\t"
 		"str	r9, [%[regs], #13*4]	\n\t"
+		"mov	r7, r11			\n\t"
 		:
 		: [regs] "r" (regs), [fn] "r" (asi->insn_fn)
-		: "r0", "r1", "r2", "r3", "r4", "r5", "r6", "r7", "r9",
+		: "r0", "r1", "r2", "r3", "r4", "r5", "r6", "r9", "r11",
 		  "lr", "memory", "cc"
 		);
 }
@@ -577,14 +583,16 @@ t16_emulate_pop_pc(probes_opcode_t insn,
 	register unsigned long pc asm("r8");
 
 	__asm__ __volatile__ (
+		"mov	r11, r7			\n\t"
 		"ldr	r9, [%[regs], #13*4]	\n\t"
 		"ldmia	%[regs], {r0-r7}	\n\t"
 		"blx	%[fn]			\n\t"
 		"stmia	%[regs], {r0-r7}	\n\t"
 		"str	r9, [%[regs], #13*4]	\n\t"
+		"mov	r7, r11			\n\t"
 		: "=r" (pc)
 		: [regs] "r" (regs), [fn] "r" (asi->insn_fn)
-		: "r0", "r1", "r2", "r3", "r4", "r5", "r6", "r7", "r9",
+		: "r0", "r1", "r2", "r3", "r4", "r5", "r6", "r9", "r11",
 		  "lr", "memory", "cc"
 		);
 
diff --git a/arch/arm/tools/Makefile b/arch/arm/tools/Makefile
index 4a5c50f67ced..81f13bdf32f2 100644
--- a/arch/arm/tools/Makefile
+++ b/arch/arm/tools/Makefile
@@ -29,8 +29,7 @@ kapi:	$(kapi-hdrs-y) $(gen-y)
 uapi:	$(uapi-hdrs-y)
 
 # Create output directory if not already present
-_dummy := $(shell [ -d '$(kapi)' ] || mkdir -p '$(kapi)') \
-          $(shell [ -d '$(uapi)' ] || mkdir -p '$(uapi)')
+$(shell mkdir -p $(kapi) $(uapi))
 
 quiet_cmd_gen_mach = GEN     $@
       cmd_gen_mach = $(AWK) -f $(real-prereqs) > $@
diff --git a/arch/arm/tools/syscall.tbl b/arch/arm/tools/syscall.tbl
index 543100151f2b..ac964612d8b0 100644
--- a/arch/arm/tools/syscall.tbl
+++ b/arch/arm/tools/syscall.tbl
@@ -463,3 +463,4 @@
 # 447 reserved for memfd_secret
 448	common	process_mrelease		sys_process_mrelease
 449	common	futex_waitv			sys_futex_waitv
+450	common	set_mempolicy_home_node		sys_set_mempolicy_home_node
diff --git a/arch/arm/vdso/Makefile b/arch/arm/vdso/Makefile
index 7c9e395b77f7..8ca1c9f262a2 100644
--- a/arch/arm/vdso/Makefile
+++ b/arch/arm/vdso/Makefile
@@ -18,7 +18,7 @@ ccflags-y += -DDISABLE_BRANCH_PROFILING -DBUILD_VDSO32
 
 ldflags-$(CONFIG_CPU_ENDIAN_BE8) := --be8
 ldflags-y := -Bsymbolic --no-undefined -soname=linux-vdso.so.1 \
-	    -z max-page-size=4096 -nostdlib -shared $(ldflags-y) \
+	    -z max-page-size=4096 -shared $(ldflags-y) \
 	    --hash-style=sysv --build-id=sha1 \
 	    -T
 
@@ -28,7 +28,7 @@ CPPFLAGS_vdso.lds += -P -C -U$(ARCH)
 CFLAGS_REMOVE_vdso.o = -pg
 
 # Force -O2 to avoid libgcc dependencies
-CFLAGS_REMOVE_vgettimeofday.o = -pg -Os $(GCC_PLUGINS_CFLAGS)
+CFLAGS_REMOVE_vgettimeofday.o = -pg -Os $(RANDSTRUCT_CFLAGS) $(GCC_PLUGINS_CFLAGS)
 ifeq ($(c-gettimeofday-y),)
 CFLAGS_vgettimeofday.o = -O2
 else
diff --git a/arch/arm/xen/enlighten.c b/arch/arm/xen/enlighten.c
index 7619fbffcea2..93c8ccbf2982 100644
--- a/arch/arm/xen/enlighten.c
+++ b/arch/arm/xen/enlighten.c
@@ -34,6 +34,7 @@
 #include <linux/timekeeping.h>
 #include <linux/timekeeper_internal.h>
 #include <linux/acpi.h>
+#include <linux/virtio_anchor.h>
 
 #include <linux/mm.h>
 
@@ -59,6 +60,10 @@ unsigned long xen_released_pages;
 struct xen_memory_region xen_extra_mem[XEN_EXTRA_MEM_MAX_REGIONS] __initdata;
 
 static __read_mostly unsigned int xen_events_irq;
+static __read_mostly phys_addr_t xen_grant_frames;
+
+#define GRANT_TABLE_INDEX   0
+#define EXT_REGION_INDEX    1
 
 uint32_t xen_start_flags;
 EXPORT_SYMBOL(xen_start_flags);
@@ -300,9 +305,118 @@ static void __init xen_acpi_guest_init(void)
 #endif
 }
 
+#ifdef CONFIG_XEN_UNPOPULATED_ALLOC
+/*
+ * A type-less specific Xen resource which contains extended regions
+ * (unused regions of guest physical address space provided by the hypervisor).
+ */
+static struct resource xen_resource = {
+	.name = "Xen unused space",
+};
+
+int __init arch_xen_unpopulated_init(struct resource **res)
+{
+	struct device_node *np;
+	struct resource *regs, *tmp_res;
+	uint64_t min_gpaddr = -1, max_gpaddr = 0;
+	unsigned int i, nr_reg = 0;
+	int rc;
+
+	if (!xen_domain())
+		return -ENODEV;
+
+	if (!acpi_disabled)
+		return -ENODEV;
+
+	np = of_find_compatible_node(NULL, NULL, "xen,xen");
+	if (WARN_ON(!np))
+		return -ENODEV;
+
+	/* Skip region 0 which is reserved for grant table space */
+	while (of_get_address(np, nr_reg + EXT_REGION_INDEX, NULL, NULL))
+		nr_reg++;
+
+	if (!nr_reg) {
+		pr_err("No extended regions are found\n");
+		of_node_put(np);
+		return -EINVAL;
+	}
+
+	regs = kcalloc(nr_reg, sizeof(*regs), GFP_KERNEL);
+	if (!regs) {
+		of_node_put(np);
+		return -ENOMEM;
+	}
+
+	/*
+	 * Create resource from extended regions provided by the hypervisor to be
+	 * used as unused address space for Xen scratch pages.
+	 */
+	for (i = 0; i < nr_reg; i++) {
+		rc = of_address_to_resource(np, i + EXT_REGION_INDEX, &regs[i]);
+		if (rc)
+			goto err;
+
+		if (max_gpaddr < regs[i].end)
+			max_gpaddr = regs[i].end;
+		if (min_gpaddr > regs[i].start)
+			min_gpaddr = regs[i].start;
+	}
+
+	xen_resource.start = min_gpaddr;
+	xen_resource.end = max_gpaddr;
+
+	/*
+	 * Mark holes between extended regions as unavailable. The rest of that
+	 * address space will be available for the allocation.
+	 */
+	for (i = 1; i < nr_reg; i++) {
+		resource_size_t start, end;
+
+		/* There is an overlap between regions */
+		if (regs[i - 1].end + 1 > regs[i].start) {
+			rc = -EINVAL;
+			goto err;
+		}
+
+		/* There is no hole between regions */
+		if (regs[i - 1].end + 1 == regs[i].start)
+			continue;
+
+		start = regs[i - 1].end + 1;
+		end = regs[i].start - 1;
+
+		tmp_res = kzalloc(sizeof(*tmp_res), GFP_KERNEL);
+		if (!tmp_res) {
+			rc = -ENOMEM;
+			goto err;
+		}
+
+		tmp_res->name = "Unavailable space";
+		tmp_res->start = start;
+		tmp_res->end = end;
+
+		rc = insert_resource(&xen_resource, tmp_res);
+		if (rc) {
+			pr_err("Cannot insert resource %pR (%d)\n", tmp_res, rc);
+			kfree(tmp_res);
+			goto err;
+		}
+	}
+
+	*res = &xen_resource;
+
+err:
+	of_node_put(np);
+	kfree(regs);
+	return rc;
+}
+#endif
+
 static void __init xen_dt_guest_init(void)
 {
 	struct device_node *xen_node;
+	struct resource res;
 
 	xen_node = of_find_compatible_node(NULL, NULL, "xen,xen");
 	if (!xen_node) {
@@ -311,17 +425,28 @@ static void __init xen_dt_guest_init(void)
 	}
 
 	xen_events_irq = irq_of_parse_and_map(xen_node, 0);
+
+	if (of_address_to_resource(xen_node, GRANT_TABLE_INDEX, &res)) {
+		pr_err("Xen grant table region is not found\n");
+		of_node_put(xen_node);
+		return;
+	}
+	of_node_put(xen_node);
+	xen_grant_frames = res.start;
 }
 
 static int __init xen_guest_init(void)
 {
 	struct xen_add_to_physmap xatp;
 	struct shared_info *shared_info_page = NULL;
-	int cpu;
+	int rc, cpu;
 
 	if (!xen_domain())
 		return 0;
 
+	if (IS_ENABLED(CONFIG_XEN_VIRTIO))
+		virtio_set_mem_acc_cb(xen_virtio_mem_acc);
+
 	if (!acpi_disabled)
 		xen_acpi_guest_init();
 	else
@@ -370,12 +495,16 @@ static int __init xen_guest_init(void)
 	for_each_possible_cpu(cpu)
 		per_cpu(xen_vcpu_id, cpu) = cpu;
 
-	xen_auto_xlat_grant_frames.count = gnttab_max_grant_frames();
-	if (xen_xlate_map_ballooned_pages(&xen_auto_xlat_grant_frames.pfn,
-					  &xen_auto_xlat_grant_frames.vaddr,
-					  xen_auto_xlat_grant_frames.count)) {
+	if (!xen_grant_frames) {
+		xen_auto_xlat_grant_frames.count = gnttab_max_grant_frames();
+		rc = xen_xlate_map_ballooned_pages(&xen_auto_xlat_grant_frames.pfn,
+										   &xen_auto_xlat_grant_frames.vaddr,
+										   xen_auto_xlat_grant_frames.count);
+	} else
+		rc = gnttab_setup_auto_xlat_frames(xen_grant_frames);
+	if (rc) {
 		free_percpu(xen_vcpu_info);
-		return -ENOMEM;
+		return rc;
 	}
 	gnttab_init();
 
diff --git a/arch/arm/xen/mm.c b/arch/arm/xen/mm.c
index a7e54a087b80..3d826c0b5fee 100644
--- a/arch/arm/xen/mm.c
+++ b/arch/arm/xen/mm.c
@@ -23,22 +23,20 @@
 #include <asm/xen/hypercall.h>
 #include <asm/xen/interface.h>
 
-unsigned long xen_get_swiotlb_free_pages(unsigned int order)
+static gfp_t xen_swiotlb_gfp(void)
 {
 	phys_addr_t base;
-	gfp_t flags = __GFP_NOWARN|__GFP_KSWAPD_RECLAIM;
 	u64 i;
 
 	for_each_mem_range(i, &base, NULL) {
 		if (base < (phys_addr_t)0xffffffff) {
 			if (IS_ENABLED(CONFIG_ZONE_DMA32))
-				flags |= __GFP_DMA32;
-			else
-				flags |= __GFP_DMA;
-			break;
+				return __GFP_DMA32;
+			return __GFP_DMA;
 		}
 	}
-	return __get_free_pages(flags, order);
+
+	return GFP_KERNEL;
 }
 
 static bool hypercall_cflush = false;
@@ -118,23 +116,6 @@ bool xen_arch_need_swiotlb(struct device *dev,
 		!dev_is_dma_coherent(dev));
 }
 
-int xen_create_contiguous_region(phys_addr_t pstart, unsigned int order,
-				 unsigned int address_bits,
-				 dma_addr_t *dma_handle)
-{
-	if (!xen_initial_domain())
-		return -EINVAL;
-
-	/* we assume that dom0 is mapped 1:1 for now */
-	*dma_handle = pstart;
-	return 0;
-}
-
-void xen_destroy_contiguous_region(phys_addr_t pstart, unsigned int order)
-{
-	return;
-}
-
 static int __init xen_mm_init(void)
 {
 	struct gnttab_cache_flush cflush;
@@ -143,10 +124,13 @@ static int __init xen_mm_init(void)
 	if (!xen_swiotlb_detect())
 		return 0;
 
-	rc = xen_swiotlb_init();
 	/* we can work with the default swiotlb */
-	if (rc < 0 && rc != -EEXIST)
-		return rc;
+	if (!io_tlb_default_mem.nslabs) {
+		rc = swiotlb_init_late(swiotlb_size_or_default(),
+				       xen_swiotlb_gfp(), NULL);
+		if (rc < 0)
+			return rc;
+	}
 
 	cflush.op = 0;
 	cflush.a.dev_bus_addr = 0;
diff --git a/arch/arm/xen/p2m.c b/arch/arm/xen/p2m.c
index 84a1cea1f43b..309648c17f48 100644
--- a/arch/arm/xen/p2m.c
+++ b/arch/arm/xen/p2m.c
@@ -63,11 +63,12 @@ out:
 
 unsigned long __pfn_to_mfn(unsigned long pfn)
 {
-	struct rb_node *n = phys_to_mach.rb_node;
+	struct rb_node *n;
 	struct xen_p2m_entry *entry;
 	unsigned long irqflags;
 
 	read_lock_irqsave(&p2m_lock, irqflags);
+	n = phys_to_mach.rb_node;
 	while (n) {
 		entry = rb_entry(n, struct xen_p2m_entry, rbnode_phys);
 		if (entry->pfn <= pfn &&
@@ -152,10 +153,11 @@ bool __set_phys_to_machine_multi(unsigned long pfn,
 	int rc;
 	unsigned long irqflags;
 	struct xen_p2m_entry *p2m_entry;
-	struct rb_node *n = phys_to_mach.rb_node;
+	struct rb_node *n;
 
 	if (mfn == INVALID_P2M_ENTRY) {
 		write_lock_irqsave(&p2m_lock, irqflags);
+		n = phys_to_mach.rb_node;
 		while (n) {
 			p2m_entry = rb_entry(n, struct xen_p2m_entry, rbnode_phys);
 			if (p2m_entry->pfn <= pfn &&
diff --git a/arch/arm64/Kconfig b/arch/arm64/Kconfig
index 5e2dfef78956..505c8a1ccbe0 100644
--- a/arch/arm64/Kconfig
+++ b/arch/arm64/Kconfig
@@ -10,6 +10,7 @@ config ARM64
 	select ACPI_SPCR_TABLE if ACPI
 	select ACPI_PPTT if ACPI
 	select ARCH_HAS_DEBUG_WX
+	select ARCH_BINFMT_ELF_EXTRA_PHDRS
 	select ARCH_BINFMT_ELF_STATE
 	select ARCH_CORRECT_STACKTRACE_ON_KRETPROBE
 	select ARCH_ENABLE_HUGEPAGE_MIGRATION if HUGETLB_PAGE && MIGRATION
@@ -18,6 +19,7 @@ config ARM64
 	select ARCH_ENABLE_SPLIT_PMD_PTLOCK if PGTABLE_LEVELS > 2
 	select ARCH_ENABLE_THP_MIGRATION if TRANSPARENT_HUGEPAGE
 	select ARCH_HAS_CACHE_LINE_SIZE
+	select ARCH_HAS_CURRENT_STACK_POINTER
 	select ARCH_HAS_DEBUG_VIRTUAL
 	select ARCH_HAS_DEBUG_VM_PGTABLE
 	select ARCH_HAS_DMA_PREP_COHERENT
@@ -46,6 +48,7 @@ config ARM64
 	select ARCH_HAS_ZONE_DMA_SET if EXPERT
 	select ARCH_HAVE_ELF_PROT
 	select ARCH_HAVE_NMI_SAFE_CMPXCHG
+	select ARCH_HAVE_TRACE_MMIO_ACCESS
 	select ARCH_INLINE_READ_LOCK if !PREEMPTION
 	select ARCH_INLINE_READ_LOCK_BH if !PREEMPTION
 	select ARCH_INLINE_READ_LOCK_IRQ if !PREEMPTION
@@ -89,13 +92,16 @@ config ARM64
 	select ARCH_SUPPORTS_ATOMIC_RMW
 	select ARCH_SUPPORTS_INT128 if CC_HAS_INT128
 	select ARCH_SUPPORTS_NUMA_BALANCING
+	select ARCH_SUPPORTS_PAGE_TABLE_CHECK
 	select ARCH_WANT_COMPAT_IPC_PARSE_VERSION if COMPAT
 	select ARCH_WANT_DEFAULT_BPF_JIT
 	select ARCH_WANT_DEFAULT_TOPDOWN_MMAP_LAYOUT
 	select ARCH_WANT_FRAME_POINTERS
 	select ARCH_WANT_HUGE_PMD_SHARE if ARM64_4K_PAGES || (ARM64_16K_PAGES && !ARM64_VA_BITS_36)
+	select ARCH_WANT_HUGETLB_PAGE_OPTIMIZE_VMEMMAP
 	select ARCH_WANT_LD_ORPHAN_WARN
 	select ARCH_WANTS_NO_INSTR
+	select ARCH_WANTS_THP_SWAP if ARM64_4K_PAGES
 	select ARCH_HAS_UBSAN_SANITIZE_ALL
 	select ARM_AMBA
 	select ARM_ARCH_TIMER
@@ -120,8 +126,8 @@ config ARM64
 	select GENERIC_CPU_AUTOPROBE
 	select GENERIC_CPU_VULNERABILITIES
 	select GENERIC_EARLY_IOREMAP
-	select GENERIC_FIND_FIRST_BIT
 	select GENERIC_IDLE_POLL_SETUP
+	select GENERIC_IOREMAP
 	select GENERIC_IRQ_IPI
 	select GENERIC_IRQ_PROBE
 	select GENERIC_IRQ_SHOW
@@ -143,6 +149,7 @@ config ARM64
 	select HAVE_ARCH_AUDITSYSCALL
 	select HAVE_ARCH_BITREVERSE
 	select HAVE_ARCH_COMPILER_H
+	select HAVE_ARCH_HUGE_VMALLOC
 	select HAVE_ARCH_HUGE_VMAP
 	select HAVE_ARCH_JUMP_LABEL
 	select HAVE_ARCH_JUMP_LABEL_RELATIVE
@@ -150,6 +157,8 @@ config ARM64
 	select HAVE_ARCH_KASAN_VMALLOC if HAVE_ARCH_KASAN
 	select HAVE_ARCH_KASAN_SW_TAGS if HAVE_ARCH_KASAN
 	select HAVE_ARCH_KASAN_HW_TAGS if (HAVE_ARCH_KASAN && ARM64_MTE)
+	# Some instrumentation may be unsound, hence EXPERT
+	select HAVE_ARCH_KCSAN if EXPERT
 	select HAVE_ARCH_KFENCE
 	select HAVE_ARCH_KGDB
 	select HAVE_ARCH_MMAP_RND_BITS
@@ -168,12 +177,10 @@ config ARM64
 	select HAVE_C_RECORDMCOUNT
 	select HAVE_CMPXCHG_DOUBLE
 	select HAVE_CMPXCHG_LOCAL
-	select HAVE_CONTEXT_TRACKING
+	select HAVE_CONTEXT_TRACKING_USER
 	select HAVE_DEBUG_KMEMLEAK
 	select HAVE_DMA_CONTIGUOUS
 	select HAVE_DYNAMIC_FTRACE
-	select HAVE_DYNAMIC_FTRACE_WITH_REGS \
-		if $(cc-option,-fpatchable-function-entry=2)
 	select FTRACE_MCOUNT_USE_PATCHABLE_FUNCTION_ENTRY \
 		if DYNAMIC_FTRACE_WITH_REGS
 	select HAVE_EFFICIENT_UNALIGNED_ACCESS
@@ -184,13 +191,14 @@ config ARM64
 	select HAVE_FUNCTION_GRAPH_TRACER
 	select HAVE_GCC_PLUGINS
 	select HAVE_HW_BREAKPOINT if PERF_EVENTS
+	select HAVE_IOREMAP_PROT
 	select HAVE_IRQ_TIME_ACCOUNTING
 	select HAVE_KVM
 	select HAVE_NMI
-	select HAVE_PATA_PLATFORM
 	select HAVE_PERF_EVENTS
 	select HAVE_PERF_REGS
 	select HAVE_PERF_USER_STACK_DUMP
+	select HAVE_PREEMPT_DYNAMIC_KEY
 	select HAVE_REGS_AND_STACK_ACCESS_API
 	select HAVE_POSIX_CPU_TIMERS_TASK_WORK
 	select HAVE_FUNCTION_ARG_ACCESS_API
@@ -201,10 +209,9 @@ config ARM64
 	select HAVE_KPROBES
 	select HAVE_KRETPROBES
 	select HAVE_GENERIC_VDSO
-	select IOMMU_DMA if IOMMU_SUPPORT
 	select IRQ_DOMAIN
 	select IRQ_FORCED_THREADING
-	select KASAN_VMALLOC if KASAN_GENERIC
+	select KASAN_VMALLOC if KASAN
 	select MODULES_USE_ELF_RELA
 	select NEED_DMA_MAP_STATE
 	select NEED_SG_DMA_LENGTH
@@ -221,9 +228,22 @@ config ARM64
 	select THREAD_INFO_IN_TASK
 	select HAVE_ARCH_USERFAULTFD_MINOR if USERFAULTFD
 	select TRACE_IRQFLAGS_SUPPORT
+	select TRACE_IRQFLAGS_NMI_SUPPORT
+	select HAVE_SOFTIRQ_ON_OWN_STACK
 	help
 	  ARM 64-bit (AArch64) Linux support.
 
+config CLANG_SUPPORTS_DYNAMIC_FTRACE_WITH_REGS
+	def_bool CC_IS_CLANG
+	# https://github.com/ClangBuiltLinux/linux/issues/1507
+	depends on AS_IS_GNU || (AS_IS_LLVM && (LD_IS_LLD || LD_VERSION >= 23600))
+	select HAVE_DYNAMIC_FTRACE_WITH_REGS
+
+config GCC_SUPPORTS_DYNAMIC_FTRACE_WITH_REGS
+	def_bool CC_IS_GCC
+	depends on $(cc-option,-fpatchable-function-entry=2)
+	select HAVE_DYNAMIC_FTRACE_WITH_REGS
+
 config 64BIT
 	def_bool y
 
@@ -249,31 +269,31 @@ config ARM64_CONT_PMD_SHIFT
 	default 4
 
 config ARCH_MMAP_RND_BITS_MIN
-       default 14 if ARM64_64K_PAGES
-       default 16 if ARM64_16K_PAGES
-       default 18
+	default 14 if ARM64_64K_PAGES
+	default 16 if ARM64_16K_PAGES
+	default 18
 
 # max bits determined by the following formula:
 #  VA_BITS - PAGE_SHIFT - 3
 config ARCH_MMAP_RND_BITS_MAX
-       default 19 if ARM64_VA_BITS=36
-       default 24 if ARM64_VA_BITS=39
-       default 27 if ARM64_VA_BITS=42
-       default 30 if ARM64_VA_BITS=47
-       default 29 if ARM64_VA_BITS=48 && ARM64_64K_PAGES
-       default 31 if ARM64_VA_BITS=48 && ARM64_16K_PAGES
-       default 33 if ARM64_VA_BITS=48
-       default 14 if ARM64_64K_PAGES
-       default 16 if ARM64_16K_PAGES
-       default 18
+	default 19 if ARM64_VA_BITS=36
+	default 24 if ARM64_VA_BITS=39
+	default 27 if ARM64_VA_BITS=42
+	default 30 if ARM64_VA_BITS=47
+	default 29 if ARM64_VA_BITS=48 && ARM64_64K_PAGES
+	default 31 if ARM64_VA_BITS=48 && ARM64_16K_PAGES
+	default 33 if ARM64_VA_BITS=48
+	default 14 if ARM64_64K_PAGES
+	default 16 if ARM64_16K_PAGES
+	default 18
 
 config ARCH_MMAP_RND_COMPAT_BITS_MIN
-       default 7 if ARM64_64K_PAGES
-       default 9 if ARM64_16K_PAGES
-       default 11
+	default 7 if ARM64_64K_PAGES
+	default 9 if ARM64_16K_PAGES
+	default 11
 
 config ARCH_MMAP_RND_COMPAT_BITS_MAX
-       default 16
+	default 16
 
 config NO_IOPORT_MAP
 	def_bool y if !PCI
@@ -300,7 +320,7 @@ config GENERIC_HWEIGHT
 	def_bool y
 
 config GENERIC_CSUM
-        def_bool y
+	def_bool y
 
 config GENERIC_CALIBRATE_DELAY
 	def_bool y
@@ -487,6 +507,22 @@ config ARM64_ERRATUM_834220
 
 	  If unsure, say Y.
 
+config ARM64_ERRATUM_1742098
+	bool "Cortex-A57/A72: 1742098: ELR recorded incorrectly on interrupt taken between cryptographic instructions in a sequence"
+	depends on COMPAT
+	default y
+	help
+	  This option removes the AES hwcap for aarch32 user-space to
+	  workaround erratum 1742098 on Cortex-A57 and Cortex-A72.
+
+	  Affected parts may corrupt the AES state if an interrupt is
+	  taken between a pair of AES instructions. These instructions
+	  are only present if the cryptography extensions are present.
+	  All software should have a fallback implementation for CPUs
+	  that don't implement the cryptography extensions.
+
+	  If unsure, say Y.
+
 config ARM64_ERRATUM_845719
 	bool "Cortex-A53: 845719: a load might read incorrect data"
 	depends on COMPAT
@@ -596,6 +632,23 @@ config ARM64_ERRATUM_1530923
 config ARM64_WORKAROUND_REPEAT_TLBI
 	bool
 
+config ARM64_ERRATUM_2441007
+	bool "Cortex-A55: Completion of affected memory accesses might not be guaranteed by completion of a TLBI"
+	default y
+	select ARM64_WORKAROUND_REPEAT_TLBI
+	help
+	  This option adds a workaround for ARM Cortex-A55 erratum #2441007.
+
+	  Under very rare circumstances, affected Cortex-A55 CPUs
+	  may not handle a race between a break-before-make sequence on one
+	  CPU, and another CPU accessing the same page. This could allow a
+	  store to a page that has been unmapped.
+
+	  Work around this by adding the affected CPUs to the list that needs
+	  TLB sequences to be done twice.
+
+	  If unsure, say Y.
+
 config ARM64_ERRATUM_1286807
 	bool "Cortex-A76: Modification of the translation table for a virtual address might lead to read-after-read ordering violation"
 	default y
@@ -669,15 +722,56 @@ config ARM64_ERRATUM_1508412
 config ARM64_WORKAROUND_TRBE_OVERWRITE_FILL_MODE
 	bool
 
+config ARM64_ERRATUM_2051678
+	bool "Cortex-A510: 2051678: disable Hardware Update of the page table dirty bit"
+	default y
+	help
+	  This options adds the workaround for ARM Cortex-A510 erratum ARM64_ERRATUM_2051678.
+	  Affected Cortex-A510 might not respect the ordering rules for
+	  hardware update of the page table's dirty bit. The workaround
+	  is to not enable the feature on affected CPUs.
+
+	  If unsure, say Y.
+
+config ARM64_ERRATUM_2077057
+	bool "Cortex-A510: 2077057: workaround software-step corrupting SPSR_EL2"
+	default y
+	help
+	  This option adds the workaround for ARM Cortex-A510 erratum 2077057.
+	  Affected Cortex-A510 may corrupt SPSR_EL2 when the a step exception is
+	  expected, but a Pointer Authentication trap is taken instead. The
+	  erratum causes SPSR_EL1 to be copied to SPSR_EL2, which could allow
+	  EL1 to cause a return to EL2 with a guest controlled ELR_EL2.
+
+	  This can only happen when EL2 is stepping EL1.
+
+	  When these conditions occur, the SPSR_EL2 value is unchanged from the
+	  previous guest entry, and can be restored from the in-memory copy.
+
+	  If unsure, say Y.
+
+config ARM64_ERRATUM_2658417
+	bool "Cortex-A510: 2658417: remove BF16 support due to incorrect result"
+	default y
+	help
+	  This option adds the workaround for ARM Cortex-A510 erratum 2658417.
+	  Affected Cortex-A510 (r0p0 to r1p1) may produce the wrong result for
+	  BFMMLA or VMMLA instructions in rare circumstances when a pair of
+	  A510 CPUs are using shared neon hardware. As the sharing is not
+	  discoverable by the kernel, hide the BF16 HWCAP to indicate that
+	  user-space should not be using these instructions.
+
+	  If unsure, say Y.
+
 config ARM64_ERRATUM_2119858
-	bool "Cortex-A710: 2119858: workaround TRBE overwriting trace data in FILL mode"
+	bool "Cortex-A710/X2: 2119858: workaround TRBE overwriting trace data in FILL mode"
 	default y
 	depends on CORESIGHT_TRBE
 	select ARM64_WORKAROUND_TRBE_OVERWRITE_FILL_MODE
 	help
-	  This option adds the workaround for ARM Cortex-A710 erratum 2119858.
+	  This option adds the workaround for ARM Cortex-A710/X2 erratum 2119858.
 
-	  Affected Cortex-A710 cores could overwrite up to 3 cache lines of trace
+	  Affected Cortex-A710/X2 cores could overwrite up to 3 cache lines of trace
 	  data at the base of the buffer (pointed to by TRBASER_EL1) in FILL mode in
 	  the event of a WRAP event.
 
@@ -760,14 +854,14 @@ config ARM64_ERRATUM_2253138
 	  If unsure, say Y.
 
 config ARM64_ERRATUM_2224489
-	bool "Cortex-A710: 2224489: workaround TRBE writing to address out-of-range"
+	bool "Cortex-A710/X2: 2224489: workaround TRBE writing to address out-of-range"
 	depends on CORESIGHT_TRBE
 	default y
 	select ARM64_WORKAROUND_TRBE_WRITE_OUT_OF_RANGE
 	help
-	  This option adds the workaround for ARM Cortex-A710 erratum 2224489.
+	  This option adds the workaround for ARM Cortex-A710/X2 erratum 2224489.
 
-	  Affected Cortex-A710 cores might write to an out-of-range address, not reserved
+	  Affected Cortex-A710/X2 cores might write to an out-of-range address, not reserved
 	  for TRBE. Under some conditions, the TRBE might generate a write to the next
 	  virtually addressed page following the last page of the TRBE address space
 	  (i.e., the TRBLIMITR_EL1.LIMIT), instead of wrapping around to the base.
@@ -777,6 +871,99 @@ config ARM64_ERRATUM_2224489
 
 	  If unsure, say Y.
 
+config ARM64_ERRATUM_2441009
+	bool "Cortex-A510: Completion of affected memory accesses might not be guaranteed by completion of a TLBI"
+	default y
+	select ARM64_WORKAROUND_REPEAT_TLBI
+	help
+	  This option adds a workaround for ARM Cortex-A510 erratum #2441009.
+
+	  Under very rare circumstances, affected Cortex-A510 CPUs
+	  may not handle a race between a break-before-make sequence on one
+	  CPU, and another CPU accessing the same page. This could allow a
+	  store to a page that has been unmapped.
+
+	  Work around this by adding the affected CPUs to the list that needs
+	  TLB sequences to be done twice.
+
+	  If unsure, say Y.
+
+config ARM64_ERRATUM_2064142
+	bool "Cortex-A510: 2064142: workaround TRBE register writes while disabled"
+	depends on CORESIGHT_TRBE
+	default y
+	help
+	  This option adds the workaround for ARM Cortex-A510 erratum 2064142.
+
+	  Affected Cortex-A510 core might fail to write into system registers after the
+	  TRBE has been disabled. Under some conditions after the TRBE has been disabled
+	  writes into TRBE registers TRBLIMITR_EL1, TRBPTR_EL1, TRBBASER_EL1, TRBSR_EL1,
+	  and TRBTRG_EL1 will be ignored and will not be effected.
+
+	  Work around this in the driver by executing TSB CSYNC and DSB after collection
+	  is stopped and before performing a system register write to one of the affected
+	  registers.
+
+	  If unsure, say Y.
+
+config ARM64_ERRATUM_2038923
+	bool "Cortex-A510: 2038923: workaround TRBE corruption with enable"
+	depends on CORESIGHT_TRBE
+	default y
+	help
+	  This option adds the workaround for ARM Cortex-A510 erratum 2038923.
+
+	  Affected Cortex-A510 core might cause an inconsistent view on whether trace is
+	  prohibited within the CPU. As a result, the trace buffer or trace buffer state
+	  might be corrupted. This happens after TRBE buffer has been enabled by setting
+	  TRBLIMITR_EL1.E, followed by just a single context synchronization event before
+	  execution changes from a context, in which trace is prohibited to one where it
+	  isn't, or vice versa. In these mentioned conditions, the view of whether trace
+	  is prohibited is inconsistent between parts of the CPU, and the trace buffer or
+	  the trace buffer state might be corrupted.
+
+	  Work around this in the driver by preventing an inconsistent view of whether the
+	  trace is prohibited or not based on TRBLIMITR_EL1.E by immediately following a
+	  change to TRBLIMITR_EL1.E with at least one ISB instruction before an ERET, or
+	  two ISB instructions if no ERET is to take place.
+
+	  If unsure, say Y.
+
+config ARM64_ERRATUM_1902691
+	bool "Cortex-A510: 1902691: workaround TRBE trace corruption"
+	depends on CORESIGHT_TRBE
+	default y
+	help
+	  This option adds the workaround for ARM Cortex-A510 erratum 1902691.
+
+	  Affected Cortex-A510 core might cause trace data corruption, when being written
+	  into the memory. Effectively TRBE is broken and hence cannot be used to capture
+	  trace data.
+
+	  Work around this problem in the driver by just preventing TRBE initialization on
+	  affected cpus. The firmware must have disabled the access to TRBE for the kernel
+	  on such implementations. This will cover the kernel for any firmware that doesn't
+	  do this already.
+
+	  If unsure, say Y.
+
+config ARM64_ERRATUM_2457168
+	bool "Cortex-A510: 2457168: workaround for AMEVCNTR01 incrementing incorrectly"
+	depends on ARM64_AMU_EXTN
+	default y
+	help
+	  This option adds the workaround for ARM Cortex-A510 erratum 2457168.
+
+	  The AMU counter AMEVCNTR01 (constant counter) should increment at the same rate
+	  as the system counter. On affected Cortex-A510 cores AMEVCNTR01 increments
+	  incorrectly giving a significantly higher output value.
+
+	  Work around this problem by returning 0 when reading the affected counter in
+	  key locations that results in disabling all users of this counter. This effect
+	  is the same to firmware disabling affected counters.
+
+	  If unsure, say Y.
+
 config CAVIUM_ERRATUM_22375
 	bool "Cavium erratum 22375, 24313"
 	default y
@@ -804,13 +991,17 @@ config CAVIUM_ERRATUM_23144
 	  If unsure, say Y.
 
 config CAVIUM_ERRATUM_23154
-	bool "Cavium erratum 23154: Access to ICC_IAR1_EL1 is not sync'ed"
+	bool "Cavium errata 23154 and 38545: GICv3 lacks HW synchronisation"
 	default y
 	help
-	  The gicv3 of ThunderX requires a modified version for
+	  The ThunderX GICv3 implementation requires a modified version for
 	  reading the IAR status to ensure data synchronization
 	  (access to icc_iar1_el1 is not sync'ed before and after).
 
+	  It also suffers from erratum 38545 (also present on Marvell's
+	  OcteonTX and OcteonTX2), resulting in deactivated interrupts being
+	  spuriously presented to the CPU interface.
+
 	  If unsure, say Y.
 
 config CAVIUM_ERRATUM_27456
@@ -942,8 +1133,7 @@ config SOCIONEXT_SYNQUACER_PREITS
 
 	  If unsure, say Y.
 
-endmenu
-
+endmenu # "ARM errata workarounds via the alternatives framework"
 
 choice
 	prompt "Page size"
@@ -1134,6 +1324,10 @@ config NUMA
 	select GENERIC_ARCH_NUMA
 	select ACPI_NUMA if ACPI
 	select OF_NUMA
+	select HAVE_SETUP_PER_CPU_AREA
+	select NEED_PER_CPU_EMBED_FIRST_CHUNK
+	select NEED_PER_CPU_PAGE_FIRST_CHUNK
+	select USE_PERCPU_NUMA_NODE_ID
 	help
 	  Enable NUMA (Non-Uniform Memory Access) support.
 
@@ -1150,22 +1344,6 @@ config NODES_SHIFT
 	  Specify the maximum number of NUMA Nodes available on the target
 	  system.  Increases memory reserved to accommodate various tables.
 
-config USE_PERCPU_NUMA_NODE_ID
-	def_bool y
-	depends on NUMA
-
-config HAVE_SETUP_PER_CPU_AREA
-	def_bool y
-	depends on NUMA
-
-config NEED_PER_CPU_EMBED_FIRST_CHUNK
-	def_bool y
-	depends on NUMA
-
-config NEED_PER_CPU_PAGE_FIRST_CHUNK
-	def_bool y
-	depends on NUMA
-
 source "kernel/Kconfig.hz"
 
 config ARCH_SPARSEMEM_ENABLE
@@ -1177,10 +1355,7 @@ config HW_PERF_EVENTS
 	def_bool y
 	depends on ARM_PMU
 
-config ARCH_HAS_FILTER_PGPROT
-	def_bool y
-
-# Supported by clang >= 7.0
+# Supported by clang >= 7.0 or GCC >= 12.0.0
 config CC_HAVE_SHADOW_CALL_STACK
 	def_bool $(cc-option, -fsanitize=shadow-call-stack -ffixed-x18)
 
@@ -1273,7 +1448,7 @@ config XEN
 	help
 	  Say Y if you want to run Linux in a Virtual Machine on Xen on ARM64.
 
-config FORCE_MAX_ZONEORDER
+config ARCH_FORCE_MAX_ORDER
 	int
 	default "14" if ARM64_64K_PAGES
 	default "12" if ARM64_16K_PAGES
@@ -1308,6 +1483,15 @@ config UNMAP_KERNEL_AT_EL0
 
 	  If unsure, say Y.
 
+config MITIGATE_SPECTRE_BRANCH_HISTORY
+	bool "Mitigate Spectre style attacks against branch history" if EXPERT
+	default y
+	help
+	  Speculation attacks against some high-performance processors can
+	  make use of branch history to influence future speculation.
+	  When taking an exception from user-space, a sequence of branches
+	  or a firmware call overwrites the branch history.
+
 config RODATA_FULL_DEFAULT_ENABLED
 	bool "Apply r/o permissions of VM areas also to their linear aliases"
 	default y
@@ -1408,6 +1592,9 @@ config THUMB2_COMPAT_VDSO
 	  Compile the compat vDSO with '-mthumb -fomit-frame-pointer' if y,
 	  otherwise with '-marm'.
 
+config COMPAT_ALIGNMENT_FIXUPS
+	bool "Fix up misaligned multi-word loads and stores in user space"
+
 menuconfig ARMV8_DEPRECATED
 	bool "Emulate deprecated/obsolete ARMv8 instructions"
 	depends on SYSCTL
@@ -1477,9 +1664,9 @@ config SETEND_EMULATION
 	  be unexpected results in the applications.
 
 	  If unsure, say Y
-endif
+endif # ARMV8_DEPRECATED
 
-endif
+endif # COMPAT
 
 menu "ARMv8.1 architectural features"
 
@@ -1504,15 +1691,15 @@ config ARM64_PAN
 	bool "Enable support for Privileged Access Never (PAN)"
 	default y
 	help
-	 Privileged Access Never (PAN; part of the ARMv8.1 Extensions)
-	 prevents the kernel or hypervisor from accessing user-space (EL0)
-	 memory directly.
+	  Privileged Access Never (PAN; part of the ARMv8.1 Extensions)
+	  prevents the kernel or hypervisor from accessing user-space (EL0)
+	  memory directly.
 
-	 Choosing this option will cause any unprotected (not using
-	 copy_to_user et al) memory access to fail with a permission fault.
+	  Choosing this option will cause any unprotected (not using
+	  copy_to_user et al) memory access to fail with a permission fault.
 
-	 The feature is detected at runtime, and will remain as a 'nop'
-	 instruction if the cpu does not implement the feature.
+	  The feature is detected at runtime, and will remain as a 'nop'
+	  instruction if the cpu does not implement the feature.
 
 config AS_HAS_LDAPR
 	def_bool $(as-instr,.arch_extension rcpc)
@@ -1540,10 +1727,16 @@ config ARM64_USE_LSE_ATOMICS
 	  built with binutils >= 2.25 in order for the new instructions
 	  to be used.
 
-endmenu
+endmenu # "ARMv8.1 architectural features"
 
 menu "ARMv8.2 architectural features"
 
+config AS_HAS_ARMV8_2
+	def_bool $(cc-option,-Wa$(comma)-march=armv8.2-a)
+
+config AS_HAS_SHA3
+	def_bool $(as-instr,.arch armv8.2-a+sha3)
+
 config ARM64_PMEM
 	bool "Enable support for persistent memory"
 	select ARCH_HAS_PMEM_API
@@ -1586,7 +1779,7 @@ config ARM64_CNP
 	  at runtime, and does not affect PEs that do not implement
 	  this feature.
 
-endmenu
+endmenu # "ARMv8.2 architectural features"
 
 menu "ARMv8.3 architectural features"
 
@@ -1649,7 +1842,7 @@ config AS_HAS_PAC
 config AS_HAS_CFI_NEGATE_RA_STATE
 	def_bool $(as-instr,.cfi_startproc\n.cfi_negate_ra_state\n.cfi_endproc\n)
 
-endmenu
+endmenu # "ARMv8.3 architectural features"
 
 menu "ARMv8.4 architectural features"
 
@@ -1690,7 +1883,7 @@ config ARM64_TLB_RANGE
 	  The feature introduces new assembly instructions, and they were
 	  support when binutils >= 2.30.
 
-endmenu
+endmenu # "ARMv8.4 architectural features"
 
 menu "ARMv8.5 architectural features"
 
@@ -1727,6 +1920,8 @@ config ARM64_BTI_KERNEL
 	depends on CC_HAS_BRANCH_PROT_PAC_RET_BTI
 	# https://gcc.gnu.org/bugzilla/show_bug.cgi?id=94697
 	depends on !CC_IS_GCC || GCC_VERSION >= 100100
+	# https://gcc.gnu.org/bugzilla/show_bug.cgi?id=106671
+	depends on !CC_IS_GCC
 	# https://github.com/llvm/llvm-project/commit/a88c722e687e6780dcd6a58718350dc76fcc4cc9
 	depends on !CC_IS_CLANG || CLANG_VERSION >= 120000
 	depends on (!FUNCTION_GRAPH_TRACER || DYNAMIC_FTRACE_WITH_REGS)
@@ -1752,14 +1947,6 @@ config ARM64_E0PD
 
 	  This option enables E0PD for TTBR1 where available.
 
-config ARCH_RANDOM
-	bool "Enable support for random number generation"
-	default y
-	help
-	  Random number generation (part of the ARMv8.5 Extensions)
-	  provides a high bandwidth, cryptographically secure
-	  hardware random number generator.
-
 config ARM64_AS_HAS_MTE
 	# Initial support for MTE went in binutils 2.32.0, checked with
 	# ".arch armv8.5-a+memtag" below. However, this was incomplete
@@ -1776,6 +1963,7 @@ config ARM64_MTE
 	depends on AS_HAS_LSE_ATOMICS
 	# Required for tag checking in the uaccess routines
 	depends on ARM64_PAN
+	select ARCH_HAS_SUBPAGE_FAULTS
 	select ARCH_USES_HIGH_VMA_FLAGS
 	help
 	  Memory Tagging (part of the ARMv8.5 Extensions) provides
@@ -1797,7 +1985,7 @@ config ARM64_MTE
 
 	  Documentation/arm64/memory-tagging-extension.rst.
 
-endmenu
+endmenu # "ARMv8.5 architectural features"
 
 menu "ARMv8.7 architectural features"
 
@@ -1806,12 +1994,12 @@ config ARM64_EPAN
 	default y
 	depends on ARM64_PAN
 	help
-	 Enhanced Privileged Access Never (EPAN) allows Privileged
-	 Access Never to be used with Execute-only mappings.
+	  Enhanced Privileged Access Never (EPAN) allows Privileged
+	  Access Never to be used with Execute-only mappings.
 
-	 The feature is detected at runtime, and will remain disabled
-	 if the cpu does not implement the feature.
-endmenu
+	  The feature is detected at runtime, and will remain disabled
+	  if the cpu does not implement the feature.
+endmenu # "ARMv8.7 architectural features"
 
 config ARM64_SVE
 	bool "ARM Scalable Vector Extension support"
@@ -1844,6 +2032,17 @@ config ARM64_SVE
 	  booting the kernel.  If unsure and you are not observing these
 	  symptoms, you should assume that it is safe to say Y.
 
+config ARM64_SME
+	bool "ARM Scalable Matrix Extension support"
+	default y
+	depends on ARM64_SVE
+	help
+	  The Scalable Matrix Extension (SME) is an extension to the AArch64
+	  execution state which utilises a substantial subset of the SVE
+	  instruction set, together with the addition of new architectural
+	  register state capable of holding two dimensional matrix tiles to
+	  enable various matrix operations.
+
 config ARM64_MODULE_PLTS
 	bool "Use PLTs to allow module memory to spill over into vmalloc area"
 	depends on MODULES
@@ -1887,7 +2086,7 @@ config ARM64_DEBUG_PRIORITY_MASKING
 	  the validity of ICC_PMR_EL1 when calling concerned functions.
 
 	  If unsure, say N
-endif
+endif # ARM64_PSEUDO_NMI
 
 config RELOCATABLE
 	bool "Build a relocatable kernel image" if EXPERT
@@ -1946,7 +2145,19 @@ config STACKPROTECTOR_PER_TASK
 	def_bool y
 	depends on STACKPROTECTOR && CC_HAVE_STACKPROTECTOR_SYSREG
 
-endmenu
+# The GPIO number here must be sorted by descending number. In case of
+# a multiplatform kernel, we just want the highest value required by the
+# selected platforms.
+config ARCH_NR_GPIO
+        int
+        default 2048 if ARCH_APPLE
+        default 0
+        help
+          Maximum number of GPIOs in the system.
+
+          If unsure, leave the default value.
+
+endmenu # "Kernel Features"
 
 menu "Boot options"
 
@@ -2010,7 +2221,7 @@ config EFI
 	help
 	  This option provides support for runtime services provided
 	  by UEFI firmware (such as non-volatile variables, realtime
-          clock, and platform reset). A UEFI stub is also provided to
+	  clock, and platform reset). A UEFI stub is also provided to
 	  allow the kernel to be booted as an EFI application. This
 	  is only useful on systems that have UEFI firmware.
 
@@ -2025,11 +2236,7 @@ config DMI
 	  However, even with this option, the resultant kernel should
 	  continue to boot on existing non-UEFI platforms.
 
-endmenu
-
-config SYSVIPC_COMPAT
-	def_bool y
-	depends on COMPAT && SYSVIPC
+endmenu # "Boot options"
 
 menu "Power management options"
 
@@ -2046,7 +2253,7 @@ config ARCH_HIBERNATION_HEADER
 config ARCH_SUSPEND_POSSIBLE
 	def_bool y
 
-endmenu
+endmenu # "Power management options"
 
 menu "CPU Power Management"
 
@@ -2054,12 +2261,9 @@ source "drivers/cpuidle/Kconfig"
 
 source "drivers/cpufreq/Kconfig"
 
-endmenu
+endmenu # "CPU Power Management"
 
 source "drivers/acpi/Kconfig"
 
 source "arch/arm64/kvm/Kconfig"
 
-if CRYPTO
-source "arch/arm64/crypto/Kconfig"
-endif
diff --git a/arch/arm64/Kconfig.platforms b/arch/arm64/Kconfig.platforms
index 1aa8b7073218..76580b932e44 100644
--- a/arch/arm64/Kconfig.platforms
+++ b/arch/arm64/Kconfig.platforms
@@ -11,12 +11,11 @@ config ARCH_ACTIONS
 config ARCH_SUNXI
 	bool "Allwinner sunxi 64-bit SoC Family"
 	select ARCH_HAS_RESET_CONTROLLER
-	select GENERIC_IRQ_CHIP
-	select IRQ_DOMAIN_HIERARCHY
-	select IRQ_FASTEOI_HIERARCHY_HANDLERS
 	select PINCTRL
 	select RESET_CONTROLLER
 	select SUN4I_TIMER
+	select SUN6I_R_INTC
+	select SUNXI_NMI_INTC
 	help
 	  This enables support for Allwinner sunxi based SoCs like the A64.
 
@@ -34,6 +33,11 @@ config ARCH_APPLE
 	  This enables support for Apple's in-house ARM SoC family, starting
 	  with the Apple M1.
 
+menuconfig ARCH_BCM
+	bool "Broadcom SoC Support"
+
+if ARCH_BCM
+
 config ARCH_BCM2835
 	bool "Broadcom BCM2835 family"
 	select TIMER_OF
@@ -48,14 +52,6 @@ config ARCH_BCM2835
 	  This enables support for the Broadcom BCM2837 and BCM2711 SoC.
 	  These SoCs are used in the Raspberry Pi 3 and 4 devices.
 
-config ARCH_BCM4908
-	bool "Broadcom BCM4908 family"
-	select GPIOLIB
-	help
-	  This enables support for the Broadcom BCM4906, BCM4908 and
-	  BCM49408 SoCs. These SoCs use Brahma-B53 cores and can be
-	  found in home routers.
-
 config ARCH_BCM_IPROC
 	bool "Broadcom iProc SoC Family"
 	select COMMON_CLK_IPROC
@@ -64,6 +60,26 @@ config ARCH_BCM_IPROC
 	help
 	  This enables support for Broadcom iProc based SoCs
 
+config ARCH_BCMBCA
+	bool "Broadcom Broadband Carrier Access (BCA) origin SoC"
+	select GPIOLIB
+	help
+	  Say Y if you intend to run the kernel on a Broadcom Broadband ARM-based
+	  BCA chipset.
+
+	  This enables support for Broadcom BCA ARM-based broadband chipsets,
+	  including the DSL, PON and Wireless family of chips.
+
+config ARCH_BRCMSTB
+	bool "Broadcom Set-Top-Box SoCs"
+	select ARCH_HAS_RESET_CONTROLLER
+	select GENERIC_IRQ_CHIP
+	select PINCTRL
+	help
+	  This enables support for Broadcom's ARMv8 Set Top Box SoCs
+
+endif
+
 config ARCH_BERLIN
 	bool "Marvell Berlin SoC Family"
 	select DW_APB_ICTL
@@ -78,17 +94,10 @@ config ARCH_BITMAIN
 	help
 	  This enables support for the Bitmain SoC Family.
 
-config ARCH_BRCMSTB
-	bool "Broadcom Set-Top-Box SoCs"
-	select ARCH_HAS_RESET_CONTROLLER
-	select GENERIC_IRQ_CHIP
-	select PINCTRL
-	help
-	  This enables support for Broadcom's ARMv8 Set Top Box SoCs
-
 config ARCH_EXYNOS
 	bool "ARMv8 based Samsung Exynos SoC family"
 	select COMMON_CLK_SAMSUNG
+	select CLKSRC_EXYNOS_MCT
 	select EXYNOS_PM_DOMAINS if PM_GENERIC_DOMAINS
 	select EXYNOS_PMU
 	select PINCTRL
@@ -126,12 +135,6 @@ config ARCH_K3
 	  This enables support for Texas Instruments' K3 multicore SoC
 	  architecture.
 
-config ARCH_LAYERSCAPE
-	bool "ARMv8 based Freescale Layerscape SoC family"
-	select EDAC_SUPPORT
-	help
-	  This enables support for the Freescale Layerscape SoC family.
-
 config ARCH_LG1K
 	bool "LG Electronics LG1K SoC Family"
 	help
@@ -161,7 +164,6 @@ config ARCH_MEDIATEK
 
 config ARCH_MESON
 	bool "Amlogic Platforms"
-	select COMMON_CLK
 	help
 	  This enables support for the arm64 based Amlogic SoCs
 	  such as the s905, S905X/D, S912, A113X/D or S905X/D2
@@ -183,11 +185,24 @@ config ARCH_MVEBU
 	select PINCTRL_ARMADA_37XX
 	select PINCTRL_ARMADA_AP806
 	select PINCTRL_ARMADA_CP110
+	select PINCTRL_AC5
 	help
 	  This enables support for Marvell EBU familly, including:
 	   - Armada 3700 SoC Family
 	   - Armada 7K SoC Family
 	   - Armada 8K SoC Family
+	   - 98DX2530 SoC Family
+
+menuconfig ARCH_NXP
+	bool "NXP SoC support"
+
+if ARCH_NXP
+
+config ARCH_LAYERSCAPE
+	bool "ARMv8 based Freescale Layerscape SoC family"
+	select EDAC_SUPPORT
+	help
+	  This enables support for the Freescale Layerscape SoC family.
 
 config ARCH_MXC
 	bool "ARMv8 based NXP i.MX SoC family"
@@ -203,6 +218,24 @@ config ARCH_MXC
 	  This enables support for the ARMv8 based SoCs in the
 	  NXP i.MX family.
 
+config ARCH_S32
+	bool "NXP S32 SoC Family"
+	help
+	  This enables support for the NXP S32 family of processors.
+
+endif
+
+config ARCH_NPCM
+	bool "Nuvoton NPCM Architecture"
+	select PINCTRL
+	select GPIOLIB
+	select NPCM7XX_TIMER
+	select RESET_CONTROLLER
+	select MFD_SYSCON
+	help
+	  General support for NPCM8xx BMC (Arbel).
+	  Nuvoton NPCM8xx BMC based on the Cortex A35.
+
 config ARCH_QCOM
 	bool "Qualcomm Platforms"
 	select GPIOLIB
@@ -221,7 +254,6 @@ config ARCH_RENESAS
 	bool "Renesas SoC Platforms"
 	select GPIOLIB
 	select PINCTRL
-	select SOC_BUS
 	help
 	  This enables support for the ARMv8 based Renesas SoCs.
 
@@ -235,11 +267,6 @@ config ARCH_ROCKCHIP
 	  This enables support for the ARMv8 based Rockchip chipsets,
 	  like the RK3368.
 
-config ARCH_S32
-	bool "NXP S32 SoC Family"
-	help
-	  This enables support for the NXP S32 family of processors.
-
 config ARCH_SEATTLE
 	bool "AMD Seattle SoC Family"
 	help
@@ -249,10 +276,12 @@ config ARCH_INTEL_SOCFPGA
 	bool "Intel's SoCFPGA ARMv8 Families"
 	help
 	  This enables support for Intel's SoCFPGA ARMv8 families:
-	  Stratix 10 (ex. Altera), Agilex and eASIC N5X.
+	  Stratix 10 (ex. Altera), Stratix10 Software Virtual Platform,
+	  Agilex and eASIC N5X.
 
 config ARCH_SYNQUACER
 	bool "Socionext SynQuacer SoC Family"
+	select IRQ_FASTEOI_HIERARCHY_HANDLERS
 
 config ARCH_TEGRA
 	bool "NVIDIA Tegra SoC Family"
@@ -268,6 +297,12 @@ config ARCH_TEGRA
 	help
 	  This enables support for the NVIDIA Tegra SoC family.
 
+config ARCH_TESLA_FSD
+	bool "ARMv8 based Tesla platform"
+	depends on ARCH_EXYNOS
+	help
+	  Support for ARMv8 based Tesla platforms.
+
 config ARCH_SPRD
 	bool "Spreadtrum SoC platform"
 	help
@@ -309,9 +344,6 @@ config ARCH_VISCONTI
 	help
 	  This enables support for Toshiba Visconti SoCs Family.
 
-config ARCH_VULCAN
-	def_bool n
-
 config ARCH_XGENE
 	bool "AppliedMicro X-Gene SOC Family"
 	help
@@ -322,4 +354,4 @@ config ARCH_ZYNQMP
 	help
 	  This enables support for Xilinx ZynqMP Family
 
-endmenu
+endmenu # "Platform selection"
diff --git a/arch/arm64/Makefile b/arch/arm64/Makefile
index e8cfc5868aa8..5e56d26a2239 100644
--- a/arch/arm64/Makefile
+++ b/arch/arm64/Makefile
@@ -58,6 +58,11 @@ stack_protector_prepare: prepare0
 					include/generated/asm-offsets.h))
 endif
 
+ifeq ($(CONFIG_AS_HAS_ARMV8_2), y)
+# make sure to pass the newest target architecture to -march.
+asm-arch := armv8.2-a
+endif
+
 # Ensure that if the compiler supports branch protection we default it
 # off, this will be overridden if we are using branch protection.
 branch-prot-flags-y += $(call cc-option,-mbranch-protection=none)
@@ -128,9 +133,6 @@ ifeq ($(CONFIG_DYNAMIC_FTRACE_WITH_REGS),y)
   CC_FLAGS_FTRACE := -fpatchable-function-entry=2
 endif
 
-# Default value
-head-y		:= arch/arm64/kernel/head.o
-
 ifeq ($(CONFIG_KASAN_SW_TAGS), y)
 KASAN_SHADOW_SCALE_SHIFT := 4
 else ifeq ($(CONFIG_KASAN_GENERIC), y)
@@ -146,22 +148,25 @@ libs-$(CONFIG_EFI_STUB) += $(objtree)/drivers/firmware/efi/libstub/lib.a
 
 # Default target when executing plain make
 boot		:= arch/arm64/boot
+
+ifeq ($(CONFIG_EFI_ZBOOT),)
 KBUILD_IMAGE	:= $(boot)/Image.gz
+else
+KBUILD_IMAGE	:= $(boot)/vmlinuz.efi
+endif
 
-all:	Image.gz
+all:	$(notdir $(KBUILD_IMAGE))
 
 
-Image: vmlinux
+Image vmlinuz.efi: vmlinux
 	$(Q)$(MAKE) $(build)=$(boot) $(boot)/$@
 
 Image.%: Image
 	$(Q)$(MAKE) $(build)=$(boot) $(boot)/$@
 
-install: install-image := Image
-zinstall: install-image := Image.gz
+install: KBUILD_IMAGE := $(boot)/Image
 install zinstall:
-	$(CONFIG_SHELL) $(srctree)/$(boot)/install.sh $(KERNELRELEASE) \
-	$(boot)/$(install-image) System.map "$(INSTALL_PATH)"
+	$(call cmd,install)
 
 PHONY += vdso_install
 vdso_install:
diff --git a/arch/arm64/boot/.gitignore b/arch/arm64/boot/.gitignore
index 9a7a9009d43a..af5dc61f8b43 100644
--- a/arch/arm64/boot/.gitignore
+++ b/arch/arm64/boot/.gitignore
@@ -1,3 +1,4 @@
 # SPDX-License-Identifier: GPL-2.0-only
 Image
 Image.gz
+vmlinuz*
diff --git a/arch/arm64/boot/Makefile b/arch/arm64/boot/Makefile
index ebe80faab883..c65aee088410 100644
--- a/arch/arm64/boot/Makefile
+++ b/arch/arm64/boot/Makefile
@@ -16,7 +16,7 @@
 
 OBJCOPYFLAGS_Image :=-O binary -R .note -R .note.gnu.build-id -R .comment -S
 
-targets := Image Image.bz2 Image.gz Image.lz4 Image.lzma Image.lzo
+targets := Image Image.bz2 Image.gz Image.lz4 Image.lzma Image.lzo Image.zst
 
 $(obj)/Image: vmlinux FORCE
 	$(call if_changed,objcopy)
@@ -35,3 +35,12 @@ $(obj)/Image.lzma: $(obj)/Image FORCE
 
 $(obj)/Image.lzo: $(obj)/Image FORCE
 	$(call if_changed,lzo)
+
+$(obj)/Image.zst: $(obj)/Image FORCE
+	$(call if_changed,zstd)
+
+EFI_ZBOOT_PAYLOAD	:= Image
+EFI_ZBOOT_BFD_TARGET	:= elf64-littleaarch64
+EFI_ZBOOT_MACH_TYPE	:= ARM64
+
+include $(srctree)/drivers/firmware/efi/libstub/Makefile.zboot
diff --git a/arch/arm64/boot/dts/Makefile b/arch/arm64/boot/dts/Makefile
index 639e01a4d855..7b107fa7414b 100644
--- a/arch/arm64/boot/dts/Makefile
+++ b/arch/arm64/boot/dts/Makefile
@@ -19,6 +19,7 @@ subdir-y += lg
 subdir-y += marvell
 subdir-y += mediatek
 subdir-y += microchip
+subdir-y += nuvoton
 subdir-y += nvidia
 subdir-y += qcom
 subdir-y += realtek
@@ -27,6 +28,7 @@ subdir-y += rockchip
 subdir-y += socionext
 subdir-y += sprd
 subdir-y += synaptics
+subdir-y += tesla
 subdir-y += ti
 subdir-y += toshiba
 subdir-y += xilinx
diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
index a96d9d2d8dd8..6a96494a2e0a 100644
--- a/arch/arm64/boot/dts/allwinner/Makefile
+++ b/arch/arm64/boot/dts/allwinner/Makefile
@@ -37,3 +37,6 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-orangepi-one-plus.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64-model-b.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-tanix-tx6.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-tanix-tx6-mini.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-orangepi-zero2.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-x96-mate.dtb
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a100.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-a100.dtsi
index f6d7d7f7fdab..97e3e6907acd 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a100.dtsi
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a100.dtsi
@@ -101,6 +101,18 @@
 			#reset-cells = <1>;
 		};
 
+		dma: dma-controller@3002000 {
+			compatible = "allwinner,sun50i-a100-dma";
+			reg = <0x03002000 0x1000>;
+			interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_DMA>, <&ccu CLK_MBUS_DMA>;
+			clock-names = "bus", "mbus";
+			resets = <&ccu RST_BUS_DMA>;
+			dma-channels = <8>;
+			dma-requests = <52>;
+			#dma-cells = <1>;
+		};
+
 		gic: interrupt-controller@3021000 {
 			compatible = "arm,gic-400";
 			reg = <0x03021000 0x1000>, <0x03022000 0x2000>,
@@ -203,11 +215,14 @@
 
 		i2c0: i2c@5002000 {
 			compatible = "allwinner,sun50i-a100-i2c",
+				     "allwinner,sun8i-v536-i2c",
 				     "allwinner,sun6i-a31-i2c";
 			reg = <0x05002000 0x400>;
 			interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&ccu CLK_BUS_I2C0>;
 			resets = <&ccu RST_BUS_I2C0>;
+			dmas = <&dma 43>, <&dma 43>;
+			dma-names = "rx", "tx";
 			status = "disabled";
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -215,11 +230,14 @@
 
 		i2c1: i2c@5002400 {
 			compatible = "allwinner,sun50i-a100-i2c",
+				     "allwinner,sun8i-v536-i2c",
 				     "allwinner,sun6i-a31-i2c";
 			reg = <0x05002400 0x400>;
 			interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&ccu CLK_BUS_I2C1>;
 			resets = <&ccu RST_BUS_I2C1>;
+			dmas = <&dma 44>, <&dma 44>;
+			dma-names = "rx", "tx";
 			status = "disabled";
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -227,11 +245,14 @@
 
 		i2c2: i2c@5002800 {
 			compatible = "allwinner,sun50i-a100-i2c",
+				     "allwinner,sun8i-v536-i2c",
 				     "allwinner,sun6i-a31-i2c";
 			reg = <0x05002800 0x400>;
 			interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&ccu CLK_BUS_I2C2>;
 			resets = <&ccu RST_BUS_I2C2>;
+			dmas = <&dma 45>, <&dma 45>;
+			dma-names = "rx", "tx";
 			status = "disabled";
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -239,11 +260,14 @@
 
 		i2c3: i2c@5002c00 {
 			compatible = "allwinner,sun50i-a100-i2c",
+				     "allwinner,sun8i-v536-i2c",
 				     "allwinner,sun6i-a31-i2c";
 			reg = <0x05002c00 0x400>;
 			interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&ccu CLK_BUS_I2C3>;
 			resets = <&ccu RST_BUS_I2C3>;
+			dmas = <&dma 46>, <&dma 46>;
+			dma-names = "rx", "tx";
 			status = "disabled";
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -315,11 +339,14 @@
 
 		r_i2c0: i2c@7081400 {
 			compatible = "allwinner,sun50i-a100-i2c",
+				     "allwinner,sun8i-v536-i2c",
 				     "allwinner,sun6i-a31-i2c";
 			reg = <0x07081400 0x400>;
 			interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&r_ccu CLK_R_APB2_I2C0>;
 			resets = <&r_ccu RST_R_APB2_I2C0>;
+			dmas = <&dma 50>, <&dma 50>;
+			dma-names = "rx", "tx";
 			pinctrl-names = "default";
 			pinctrl-0 = <&r_i2c0_pins>;
 			status = "disabled";
@@ -329,11 +356,14 @@
 
 		r_i2c1: i2c@7081800 {
 			compatible = "allwinner,sun50i-a100-i2c",
+				     "allwinner,sun8i-v536-i2c",
 				     "allwinner,sun6i-a31-i2c";
 			reg = <0x07081800 0x400>;
 			interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&r_ccu CLK_R_APB2_I2C1>;
 			resets = <&r_ccu RST_R_APB2_I2C1>;
+			dmas = <&dma 51>, <&dma 51>;
+			dma-names = "rx", "tx";
 			pinctrl-names = "default";
 			pinctrl-0 = <&r_i2c1_pins>;
 			status = "disabled";
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-amarula-relic.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-amarula-relic.dts
index f17cc89f472d..8233582f6288 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64-amarula-relic.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-amarula-relic.dts
@@ -58,7 +58,7 @@
 
 	wifi_pwrseq: wifi-pwrseq {
 		compatible = "mmc-pwrseq-simple";
-		clocks = <&rtc 1>;
+		clocks = <&rtc CLK_OSC32K_FANOUT>;
 		clock-names = "ext_clock";
 		reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* WL-PMU-EN: PL2 */
 	};
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
index 997a19372683..e6d5bc0f7a61 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-bananapi-m64.dts
@@ -56,7 +56,7 @@
 	wifi_pwrseq: wifi_pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */
-		clocks = <&rtc 1>;
+		clocks = <&rtc CLK_OSC32K_FANOUT>;
 		clock-names = "ext_clock";
 	};
 };
@@ -355,7 +355,7 @@
 
 	bluetooth {
 		compatible = "brcm,bcm43438-bt";
-		clocks = <&rtc 1>;
+		clocks = <&rtc CLK_OSC32K_FANOUT>;
 		clock-names = "lpo";
 		vbat-supply = <&reg_dldo2>;
 		vddio-supply = <&reg_dldo4>;
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-nanopi-a64.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-nanopi-a64.dts
index e47ff06a6fa9..0af6dcdf7515 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64-nanopi-a64.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-nanopi-a64.dts
@@ -43,7 +43,7 @@
 
 	wifi_pwrseq: wifi_pwrseq {
 		compatible = "mmc-pwrseq-simple";
-		clocks = <&rtc 1>;
+		clocks = <&rtc CLK_OSC32K_FANOUT>;
 		clock-names = "ext_clock";
 		reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */
 	};
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-olinuxino.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-olinuxino.dts
index ec7e2c0e82c1..bfb806cf6d7a 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64-olinuxino.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-olinuxino.dts
@@ -58,6 +58,15 @@
 	};
 };
 
+&codec {
+	status = "okay";
+};
+
+&codec_analog {
+	cpvdd-supply = <&reg_eldo1>;
+	status = "okay";
+};
+
 &cpu0 {
 	cpu-supply = <&reg_dcdc2>;
 };
@@ -74,6 +83,10 @@
 	cpu-supply = <&reg_dcdc2>;
 };
 
+&dai {
+	status = "okay";
+};
+
 &de {
 	status = "okay";
 };
@@ -328,6 +341,23 @@
 	vcc-hdmi-supply = <&reg_dldo1>;
 };
 
+&sound {
+	simple-audio-card,aux-devs = <&codec_analog>;
+	simple-audio-card,widgets = "Microphone", "Microphone Jack Left",
+		    "Microphone", "Microphone Jack Right",
+		    "Headphone", "Headphone Jack";
+	simple-audio-card,routing = "Left DAC", "DACL",
+		    "Right DAC", "DACR",
+		    "Headphone Jack", "HP",
+		    "ADCL", "Left ADC",
+		    "ADCR", "Right ADC",
+		    "Microphone Jack Left", "MBIAS",
+		    "MIC1", "Microphone Jack Left",
+		    "Microphone Jack Right", "MBIAS",
+		    "MIC2", "Microphone Jack Right";
+	status = "okay";
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_pb_pins>;
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-orangepi-win.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-orangepi-win.dts
index c519d9fa6967..4f8529d5ac00 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64-orangepi-win.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-orangepi-win.dts
@@ -40,7 +40,7 @@
 	leds {
 		compatible = "gpio-leds";
 
-		status {
+		led-0 {
 			label = "orangepi:green:status";
 			gpios = <&pio 7 11 GPIO_ACTIVE_HIGH>; /* PH11 */
 		};
@@ -71,7 +71,7 @@
 	wifi_pwrseq: wifi_pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		reset-gpios = <&r_pio 0 8 GPIO_ACTIVE_LOW>; /* PL8 */
-		clocks = <&rtc 1>;
+		clocks = <&rtc CLK_OSC32K_FANOUT>;
 		clock-names = "ext_clock";
 	};
 };
@@ -369,7 +369,7 @@
 	bluetooth {
 		compatible = "brcm,bcm43438-bt";
 		max-speed = <1500000>;
-		clocks = <&rtc 1>;
+		clocks = <&rtc CLK_OSC32K_FANOUT>;
 		clock-names = "lpo";
 		vbat-supply = <&reg_dldo2>;
 		vddio-supply = <&reg_dldo4>;
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts
index 34e67f5f8297..620cb3ef5f6c 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinebook.dts
@@ -15,6 +15,7 @@
 / {
 	model = "Pinebook";
 	compatible = "pine64,pinebook", "allwinner,sun50i-a64";
+	chassis-type = "laptop";
 
 	aliases {
 		serial0 = &uart0;
@@ -34,10 +35,10 @@
 		stdout-path = "serial0:115200n8";
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
-		lid_switch {
+		lid-switch {
 			label = "Lid Switch";
 			gpios = <&r_pio 0 12 GPIO_ACTIVE_LOW>; /* PL12 */
 			linux,input-type = <EV_SW>;
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.0.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.0.dts
index fb65319a3bd3..219f720b8b7d 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.0.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.0.dts
@@ -10,6 +10,10 @@
 	compatible = "pine64,pinephone-1.0", "pine64,pinephone", "allwinner,sun50i-a64";
 };
 
+&codec_analog {
+	allwinner,internal-bias-resistor;
+};
+
 &sgm3140 {
 	enable-gpios = <&pio 2 3 GPIO_ACTIVE_HIGH>; /* PC3 */
 	flash-gpios = <&pio 3 24 GPIO_ACTIVE_HIGH>; /* PD24 */
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.1.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.1.dts
index 5e59d3752178..723af64a9cee 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.1.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone-1.1.dts
@@ -29,6 +29,10 @@
 	default-brightness-level = <400>;
 };
 
+&codec_analog {
+	allwinner,internal-bias-resistor;
+};
+
 &sgm3140 {
 	enable-gpios = <&pio 3 24 GPIO_ACTIVE_HIGH>; /* PD24 */
 	flash-gpios = <&pio 2 3 GPIO_ACTIVE_HIGH>; /* PC3 */
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi
index 5b44a979f250..87847116ab6d 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinephone.dtsi
@@ -12,6 +12,8 @@
 #include <dt-bindings/pwm/pwm.h>
 
 / {
+	chassis-type = "handset";
+
 	aliases {
 		ethernet0 = &rtl8723cs;
 		serial0 = &uart0;
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab.dts
index adb0b28b06d8..0a5607f73049 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-pinetab.dts
@@ -16,6 +16,7 @@
 / {
 	model = "PineTab, Development Sample";
 	compatible = "pine64,pinetab", "allwinner,sun50i-a64";
+	chassis-type = "tablet";
 
 	aliases {
 		serial0 = &uart0;
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-teres-i.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-teres-i.dts
index aef571acd67f..1128030e4c25 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64-teres-i.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-teres-i.dts
@@ -14,6 +14,7 @@
 / {
 	model = "Olimex A64 Teres-I";
 	compatible = "olimex,a64-teres-i", "allwinner,sun50i-a64";
+	chassis-type = "laptop";
 
 	aliases {
 		serial0 = &uart0;
@@ -196,6 +197,14 @@
 	status = "okay";
 };
 
+&pio {
+	vcc-pc-supply = <&reg_dcdc1>;
+	vcc-pd-supply = <&reg_dldo2>;
+	vcc-pe-supply = <&reg_aldo1>;
+	vcc-pf-supply = <&reg_dcdc1>;  /* No dedicated supply-pin for this */
+	vcc-pg-supply = <&reg_aldo2>;
+};
+
 &pwm {
 	status = "okay";
 };
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
index 5ba379078500..77b5349f6087 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64.dtsi
@@ -4,6 +4,7 @@
 //    Copyright (C) 2015 Jens Kuske <jenskuske@gmail.com>
 
 #include <dt-bindings/clock/sun50i-a64-ccu.h>
+#include <dt-bindings/clock/sun6i-rtc.h>
 #include <dt-bindings/clock/sun8i-de2.h>
 #include <dt-bindings/clock/sun8i-r-ccu.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
@@ -660,7 +661,7 @@
 		ccu: clock@1c20000 {
 			compatible = "allwinner,sun50i-a64-ccu";
 			reg = <0x01c20000 0x400>;
-			clocks = <&osc24M>, <&rtc 0>;
+			clocks = <&osc24M>, <&rtc CLK_OSC32K>;
 			clock-names = "hosc", "losc";
 			#clock-cells = <1>;
 			#reset-cells = <1>;
@@ -673,7 +674,8 @@
 			interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&ccu CLK_BUS_PIO>, <&osc24M>, <&rtc 0>;
+			clocks = <&ccu CLK_BUS_PIO>, <&osc24M>,
+				 <&rtc CLK_OSC32K>;
 			clock-names = "apb", "hosc", "losc";
 			gpio-controller;
 			#gpio-cells = <3>;
@@ -1146,8 +1148,14 @@
 
 		mbus: dram-controller@1c62000 {
 			compatible = "allwinner,sun50i-a64-mbus";
-			reg = <0x01c62000 0x1000>;
-			clocks = <&ccu 112>;
+			reg = <0x01c62000 0x1000>,
+			      <0x01c63000 0x1000>;
+			reg-names = "mbus", "dram";
+			clocks = <&ccu CLK_MBUS>,
+				 <&ccu CLK_DRAM>,
+				 <&ccu CLK_BUS_DRAM>;
+			clock-names = "mbus", "dram", "bus";
+			interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>;
 			#address-cells = <1>;
 			#size-cells = <1>;
 			dma-ranges = <0x00000000 0x40000000 0xc0000000>;
@@ -1220,8 +1228,8 @@
 			reg-io-width = <1>;
 			interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&ccu CLK_BUS_HDMI>, <&ccu CLK_HDMI_DDC>,
-				 <&ccu CLK_HDMI>;
-			clock-names = "iahb", "isfr", "tmds";
+				 <&ccu CLK_HDMI>, <&rtc CLK_OSC32K>;
+			clock-names = "iahb", "isfr", "tmds", "cec";
 			resets = <&ccu RST_BUS_HDMI1>;
 			reset-names = "ctrl";
 			phys = <&hdmi_phy>;
@@ -1281,7 +1289,7 @@
 		r_ccu: clock@1f01400 {
 			compatible = "allwinner,sun50i-a64-r-ccu";
 			reg = <0x01f01400 0x100>;
-			clocks = <&osc24M>, <&rtc 0>, <&rtc 2>,
+			clocks = <&osc24M>, <&rtc CLK_OSC32K>, <&rtc CLK_IOSC>,
 				 <&ccu CLK_PLL_PERIPH0>;
 			clock-names = "hosc", "losc", "iosc", "pll-periph";
 			#clock-cells = <1>;
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-r1s-h5.dts b/arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-r1s-h5.dts
index 55b369534a08..a3e040da38a0 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-r1s-h5.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-nanopi-r1s-h5.dts
@@ -52,10 +52,10 @@
 		};
 	};
 
-	r-gpio-keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
-		reset {
+		key-reset {
 			label = "reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts
index 1010c1b22d2e..b5c1ff19b4c4 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts
@@ -54,10 +54,10 @@
 		};
 	};
 
-	r-gpio-keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
-		sw4 {
+		key-sw4 {
 			label = "sw4";
 			linux,code = <BTN_0>;
 			gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-prime.dts b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-prime.dts
index 74e0444af19b..d7f8bad6bb98 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-prime.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-prime.dts
@@ -48,10 +48,10 @@
 		};
 	};
 
-	r-gpio-keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
-		sw4 {
+		key-sw4 {
 			label = "sw4";
 			linux,code = <BTN_0>;
 			gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-zero-plus.dts b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-zero-plus.dts
index d13980ed7a79..7ec5ac850a0d 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-zero-plus.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-zero-plus.dts
@@ -69,7 +69,7 @@
 	pinctrl-0 = <&emac_rgmii_pins>;
 	phy-supply = <&reg_gmac_3v3>;
 	phy-handle = <&ext_rgmii_phy>;
-	phy-mode = "rgmii";
+	phy-mode = "rgmii-id";
 	status = "okay";
 };
 
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi
index 9988e87ea7b3..a56fae761a1f 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi
@@ -233,6 +233,10 @@
 	compatible = "allwinner,sun50i-h5-de2-clk";
 };
 
+&mbus {
+	compatible = "allwinner,sun50i-h5-mbus";
+};
+
 &mmc0 {
 	compatible = "allwinner,sun50i-h5-mmc",
 		     "allwinner,sun50i-a64-mmc";
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dts b/arch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dts
index 6249e9e02928..9ec49ac2f6fd 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-beelink-gs1.dts
@@ -5,6 +5,7 @@
 
 #include "sun50i-h6.dtsi"
 #include "sun50i-h6-cpu-opp.dtsi"
+#include "sun50i-h6-gpu-opp.dtsi"
 
 #include <dt-bindings/gpio/gpio.h>
 
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-gpu-opp.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h6-gpu-opp.dtsi
new file mode 100644
index 000000000000..b48049c4fc85
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-gpu-opp.dtsi
@@ -0,0 +1,87 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+// Copyright (C) 2022 Clément Péron <peron.clem@gmail.com>
+
+/ {
+	gpu_opp_table: opp-table-gpu {
+		compatible = "operating-points-v2";
+
+		opp-216000000 {
+			opp-hz = /bits/ 64 <216000000>;
+			opp-microvolt = <810000 810000 1200000>;
+		};
+
+		opp-264000000 {
+			opp-hz = /bits/ 64 <264000000>;
+			opp-microvolt = <810000 810000 1200000>;
+		};
+
+		opp-312000000 {
+			opp-hz = /bits/ 64 <312000000>;
+			opp-microvolt = <810000 810000 1200000>;
+		};
+
+		opp-336000000 {
+			opp-hz = /bits/ 64 <336000000>;
+			opp-microvolt = <810000 810000 1200000>;
+		};
+
+		opp-360000000 {
+			opp-hz = /bits/ 64 <360000000>;
+			opp-microvolt = <820000 820000 1200000>;
+		};
+
+		opp-384000000 {
+			opp-hz = /bits/ 64 <384000000>;
+			opp-microvolt = <830000 830000 1200000>;
+		};
+
+		opp-408000000 {
+			opp-hz = /bits/ 64 <408000000>;
+			opp-microvolt = <840000 840000 1200000>;
+		};
+
+		opp-420000000 {
+			opp-hz = /bits/ 64 <420000000>;
+			opp-microvolt = <850000 850000 1200000>;
+		};
+
+		opp-432000000 {
+			opp-hz = /bits/ 64 <432000000>;
+			opp-microvolt = <860000 860000 1200000>;
+		};
+
+		opp-456000000 {
+			opp-hz = /bits/ 64 <456000000>;
+			opp-microvolt = <870000 870000 1200000>;
+		};
+
+		opp-504000000 {
+			opp-hz = /bits/ 64 <504000000>;
+			opp-microvolt = <890000 890000 1200000>;
+		};
+
+		opp-540000000 {
+			opp-hz = /bits/ 64 <540000000>;
+			opp-microvolt = <910000 910000 1200000>;
+		};
+
+		opp-576000000 {
+			opp-hz = /bits/ 64 <576000000>;
+			opp-microvolt = <930000 930000 1200000>;
+		};
+
+		opp-624000000 {
+			opp-hz = /bits/ 64 <624000000>;
+			opp-microvolt = <950000 950000 1200000>;
+		};
+
+		opp-756000000 {
+			opp-hz = /bits/ 64 <756000000>;
+			opp-microvolt = <1040000 1040000 1200000>;
+		};
+	};
+};
+
+&gpu {
+	operating-points-v2 = <&gpu_opp_table>;
+};
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts
index c45d7b7fb39a..6fc65e8db220 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts
@@ -86,7 +86,7 @@
 
 	wifi_pwrseq: wifi-pwrseq {
 		compatible = "mmc-pwrseq-simple";
-		clocks = <&rtc 1>;
+		clocks = <&rtc CLK_OSC32K_FANOUT>;
 		clock-names = "ext_clock";
 		reset-gpios = <&r_pio 1 3 GPIO_ACTIVE_LOW>; /* PM3 */
 		post-power-on-delay-ms = <200>;
@@ -314,7 +314,7 @@
 
 	bluetooth {
 		compatible = "brcm,bcm4345c5";
-		clocks = <&rtc 1>;
+		clocks = <&rtc CLK_OSC32K_FANOUT>;
 		clock-names = "lpo";
 		device-wakeup-gpios = <&r_pio 1 2 GPIO_ACTIVE_HIGH>; /* PM2 */
 		host-wakeup-gpios = <&r_pio 1 1 GPIO_ACTIVE_HIGH>; /* PM1 */
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-lite2.dts b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-lite2.dts
index e8770858b5d0..fb31dcb1cb6d 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-lite2.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-lite2.dts
@@ -13,7 +13,7 @@
 
 	wifi_pwrseq: wifi_pwrseq {
 		compatible = "mmc-pwrseq-simple";
-		clocks = <&rtc 1>;
+		clocks = <&rtc CLK_OSC32K_FANOUT>;
 		clock-names = "ext_clock";
 		reset-gpios = <&r_pio 1 3 GPIO_ACTIVE_LOW>; /* PM3 */
 		post-power-on-delay-ms = <200>;
@@ -64,7 +64,7 @@
 
 	bluetooth {
 		compatible = "brcm,bcm4345c5";
-		clocks = <&rtc 1>;
+		clocks = <&rtc CLK_OSC32K_FANOUT>;
 		clock-names = "lpo";
 		device-wakeup-gpios = <&r_pio 1 2 GPIO_ACTIVE_HIGH>; /* PM2 */
 		host-wakeup-gpios = <&r_pio 1 1 GPIO_ACTIVE_HIGH>; /* PM1 */
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-tanix-tx6-mini.dts b/arch/arm64/boot/dts/allwinner/sun50i-h6-tanix-tx6-mini.dts
new file mode 100644
index 000000000000..08d84160d88f
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-tanix-tx6-mini.dts
@@ -0,0 +1,15 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+// Copyright (c) 2021 Jernej Skrabec <jernej.skrabec@gmail.com>
+
+/dts-v1/;
+
+#include "sun50i-h6-tanix.dtsi"
+
+/ {
+	model = "Tanix TX6 mini";
+	compatible = "oranth,tanix-tx6-mini", "allwinner,sun50i-h6";
+};
+
+&r_ir {
+	linux,rc-map-name = "rc-tanix-tx3mini";
+};
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-tanix-tx6.dts b/arch/arm64/boot/dts/allwinner/sun50i-h6-tanix-tx6.dts
index 8f2a80f128de..9a38ff9b3fc7 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-h6-tanix-tx6.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-tanix-tx6.dts
@@ -3,145 +3,27 @@
 
 /dts-v1/;
 
-#include "sun50i-h6.dtsi"
-#include "sun50i-h6-cpu-opp.dtsi"
-
-#include <dt-bindings/gpio/gpio.h>
+#include "sun50i-h6-tanix.dtsi"
 
 / {
 	model = "Tanix TX6";
 	compatible = "oranth,tanix-tx6", "allwinner,sun50i-h6";
-
-	aliases {
-		serial0 = &uart0;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	connector {
-		compatible = "hdmi-connector";
-		ddc-en-gpios = <&pio 7 2 GPIO_ACTIVE_HIGH>; /* PH2 */
-		type = "a";
-
-		port {
-			hdmi_con_in: endpoint {
-				remote-endpoint = <&hdmi_out_con>;
-			};
-		};
-	};
-
-	reg_vcc1v8: regulator-vcc1v8 {
-		compatible = "regulator-fixed";
-		regulator-name = "vcc1v8";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <1800000>;
-	};
-
-	reg_vcc3v3: regulator-vcc3v3 {
-		compatible = "regulator-fixed";
-		regulator-name = "vcc3v3";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-	};
-
-	reg_vdd_cpu_gpu: regulator-vdd-cpu-gpu {
-		compatible = "regulator-fixed";
-		regulator-name = "vdd-cpu-gpu";
-		regulator-min-microvolt = <1135000>;
-		regulator-max-microvolt = <1135000>;
-	};
-};
-
-&cpu0 {
-	cpu-supply = <&reg_vdd_cpu_gpu>;
-};
-
-&de {
-	status = "okay";
-};
-
-&dwc3 {
-	status = "okay";
-};
-
-&ehci0 {
-	status = "okay";
-};
-
-&ehci3 {
-	status = "okay";
-};
-
-&gpu {
-	mali-supply = <&reg_vdd_cpu_gpu>;
-	status = "okay";
-};
-
-&hdmi {
-	status = "okay";
-};
-
-&hdmi_out {
-	hdmi_out_con: endpoint {
-		remote-endpoint = <&hdmi_con_in>;
-	};
-};
-
-&mmc0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc0_pins>;
-	vmmc-supply = <&reg_vcc3v3>;
-	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
-	bus-width = <4>;
-	status = "okay";
-};
-
-&mmc2 {
-	vmmc-supply = <&reg_vcc3v3>;
-	vqmmc-supply = <&reg_vcc1v8>;
-	bus-width = <8>;
-	non-removable;
-	cap-mmc-hw-reset;
-	mmc-hs200-1_8v;
-	status = "okay";
-};
-
-&ohci0 {
-	status = "okay";
-};
-
-&ohci3 {
-	status = "okay";
-};
-
-&pio {
-	vcc-pc-supply = <&reg_vcc1v8>;
-	vcc-pd-supply = <&reg_vcc3v3>;
-	vcc-pg-supply = <&reg_vcc1v8>;
 };
 
 &r_ir {
 	linux,rc-map-name = "rc-tanix-tx5max";
-	status = "okay";
 };
 
-&uart0 {
+&uart1 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&uart0_ph_pins>;
+	pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
+	uart-has-rtscts;
 	status = "okay";
-};
 
-&usb2otg {
-	dr_mode = "host";
-	status = "okay";
-};
-
-&usb2phy {
-	status = "okay";
-};
-
-&usb3phy {
-	status = "okay";
+	bluetooth {
+		compatible = "realtek,rtl8822cs-bt";
+		device-wake-gpios = <&r_pio 1 2 GPIO_ACTIVE_HIGH>; /* PM2 */
+		host-wake-gpios = <&r_pio 1 1 GPIO_ACTIVE_HIGH>; /* PM1 */
+		enable-gpios = <&r_pio 1 4 GPIO_ACTIVE_HIGH>; /* PM4 */
+	};
 };
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-tanix.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h6-tanix.dtsi
new file mode 100644
index 000000000000..4903d6358112
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-tanix.dtsi
@@ -0,0 +1,189 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+// Copyright (c) 2019 Jernej Skrabec <jernej.skrabec@siol.net>
+
+/dts-v1/;
+
+#include "sun50i-h6.dtsi"
+#include "sun50i-h6-cpu-opp.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	connector {
+		compatible = "hdmi-connector";
+		ddc-en-gpios = <&pio 7 2 GPIO_ACTIVE_HIGH>; /* PH2 */
+		type = "a";
+
+		port {
+			hdmi_con_in: endpoint {
+				remote-endpoint = <&hdmi_out_con>;
+			};
+		};
+	};
+
+	/* used for FD650 LED display driver */
+	i2c {
+		compatible = "i2c-gpio";
+		sda-gpios = <&pio 7 6 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; /* PH6 */
+		scl-gpios = <&pio 7 5 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; /* PH5 */
+		i2c-gpio,delay-us = <5>;
+	};
+
+	reg_vcc1v8: regulator-vcc1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc1v8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	reg_vcc3v3: regulator-vcc3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	reg_vdd_cpu_gpu: regulator-vdd-cpu-gpu {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd-cpu-gpu";
+		regulator-min-microvolt = <1135000>;
+		regulator-max-microvolt = <1135000>;
+	};
+
+	sound-spdif {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "sun50i-h6-spdif";
+
+		simple-audio-card,cpu {
+			sound-dai = <&spdif>;
+		};
+
+		simple-audio-card,codec {
+			sound-dai = <&spdif_out>;
+		};
+	};
+
+	spdif_out: spdif-out {
+		#sound-dai-cells = <0>;
+		compatible = "linux,spdif-dit";
+	};
+
+	wifi_pwrseq: wifi-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		clocks = <&rtc CLK_OSC32K_FANOUT>;
+		clock-names = "ext_clock";
+		reset-gpios = <&r_pio 1 3 GPIO_ACTIVE_LOW>; /* PM3 */
+	};
+};
+
+&cpu0 {
+	cpu-supply = <&reg_vdd_cpu_gpu>;
+};
+
+&de {
+	status = "okay";
+};
+
+&dwc3 {
+	status = "okay";
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&ehci3 {
+	status = "okay";
+};
+
+&gpu {
+	mali-supply = <&reg_vdd_cpu_gpu>;
+	status = "okay";
+};
+
+&hdmi {
+	status = "okay";
+};
+
+&hdmi_out {
+	hdmi_out_con: endpoint {
+		remote-endpoint = <&hdmi_con_in>;
+	};
+};
+
+&mmc0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_pins>;
+	vmmc-supply = <&reg_vcc3v3>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&mmc1 {
+	vmmc-supply = <&reg_vcc3v3>;
+	vqmmc-supply = <&reg_vcc1v8>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+};
+
+&mmc2 {
+	vmmc-supply = <&reg_vcc3v3>;
+	vqmmc-supply = <&reg_vcc1v8>;
+	bus-width = <8>;
+	non-removable;
+	cap-mmc-hw-reset;
+	mmc-hs200-1_8v;
+	status = "okay";
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&ohci3 {
+	status = "okay";
+};
+
+&pio {
+	vcc-pc-supply = <&reg_vcc1v8>;
+	vcc-pd-supply = <&reg_vcc3v3>;
+	vcc-pg-supply = <&reg_vcc1v8>;
+};
+
+&r_ir {
+	status = "okay";
+};
+
+&spdif {
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_ph_pins>;
+	status = "okay";
+};
+
+&usb2otg {
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usb2phy {
+	status = "okay";
+};
+
+&usb3phy {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi
index 46ed529a4dc2..53f6660656ac 100644
--- a/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi
@@ -4,6 +4,7 @@
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/clock/sun50i-h6-ccu.h>
 #include <dt-bindings/clock/sun50i-h6-r-ccu.h>
+#include <dt-bindings/clock/sun6i-rtc.h>
 #include <dt-bindings/clock/sun8i-de2.h>
 #include <dt-bindings/clock/sun8i-tcon-top.h>
 #include <dt-bindings/reset/sun50i-h6-ccu.h>
@@ -153,6 +154,15 @@
 			};
 		};
 
+		video-codec-g2@1c00000 {
+			compatible = "allwinner,sun50i-h6-vpu-g2";
+			reg = <0x01c00000 0x1000>;
+			interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_VP9>, <&ccu CLK_VP9>;
+			clock-names = "bus", "mod";
+			resets = <&ccu RST_BUS_VP9>;
+		};
+
 		video-codec@1c0e000 {
 			compatible = "allwinner,sun50i-h6-video-engine";
 			reg = <0x01c0e000 0x2000>;
@@ -176,6 +186,7 @@
 			clocks = <&ccu CLK_GPU>, <&ccu CLK_BUS_GPU>;
 			clock-names = "core", "bus";
 			resets = <&ccu RST_BUS_GPU>;
+			#cooling-cells = <2>;
 			status = "disabled";
 		};
 
@@ -228,7 +239,7 @@
 		ccu: clock@3001000 {
 			compatible = "allwinner,sun50i-h6-ccu";
 			reg = <0x03001000 0x1000>;
-			clocks = <&osc24M>, <&rtc 0>, <&rtc 2>;
+			clocks = <&osc24M>, <&rtc CLK_OSC32K>, <&rtc CLK_IOSC>;
 			clock-names = "hosc", "losc", "iosc";
 			#clock-cells = <1>;
 			#reset-cells = <1>;
@@ -308,7 +319,7 @@
 				     <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&ccu CLK_APB1>, <&osc24M>, <&rtc 0>;
+			clocks = <&ccu CLK_APB1>, <&osc24M>, <&rtc CLK_OSC32K>;
 			clock-names = "apb", "hosc", "losc";
 			gpio-controller;
 			#gpio-cells = <3>;
@@ -716,7 +727,7 @@
 			interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&ccu CLK_BUS_XHCI>,
 				 <&ccu CLK_BUS_XHCI>,
-				 <&rtc 0>;
+				 <&rtc CLK_OSC32K>;
 			clock-names = "ref", "bus_early", "suspend";
 			resets = <&ccu RST_BUS_XHCI>;
 			/*
@@ -922,7 +933,7 @@
 		r_ccu: clock@7010000 {
 			compatible = "allwinner,sun50i-h6-r-ccu";
 			reg = <0x07010000 0x400>;
-			clocks = <&osc24M>, <&rtc 0>, <&rtc 2>,
+			clocks = <&osc24M>, <&rtc CLK_OSC32K>, <&rtc CLK_IOSC>,
 				 <&ccu CLK_PLL_PERIPH0>;
 			clock-names = "hosc", "losc", "iosc", "pll-periph";
 			#clock-cells = <1>;
@@ -951,7 +962,8 @@
 			interrupt-parent = <&r_intc>;
 			interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&r_ccu CLK_R_APB1>, <&osc24M>, <&rtc 0>;
+			clocks = <&r_ccu CLK_R_APB1>, <&osc24M>,
+				 <&rtc CLK_OSC32K>;
 			clock-names = "apb", "hosc", "losc";
 			gpio-controller;
 			#gpio-cells = <3>;
@@ -1061,9 +1073,55 @@
 		};
 
 		gpu-thermal {
-			polling-delay-passive = <0>;
-			polling-delay = <0>;
+			polling-delay-passive = <1000>;
+			polling-delay = <2000>;
 			thermal-sensors = <&ths 1>;
+
+			trips {
+				gpu_alert0: gpu-alert-0 {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				gpu_alert1: gpu-alert-1 {
+					temperature = <100000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				gpu_alert2: gpu-alert-2 {
+					temperature = <105000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				gpu-crit {
+					temperature = <115000>;
+					hysteresis = <0>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				// Forbid the GPU to go over 756MHz
+				map0 {
+					trip = <&gpu_alert0>;
+					cooling-device = <&gpu 1 THERMAL_NO_LIMIT>;
+				};
+
+				// Forbid the GPU to go over 624MHz
+				map1 {
+					trip = <&gpu_alert1>;
+					cooling-device = <&gpu 2 THERMAL_NO_LIMIT>;
+				};
+
+				// Forbid the GPU to go over 576MHz
+				map2 {
+					trip = <&gpu_alert2>;
+					cooling-device = <&gpu 3 THERMAL_NO_LIMIT>;
+				};
+			};
 		};
 	};
 };
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts b/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts
new file mode 100644
index 000000000000..02893f3ac99d
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts
@@ -0,0 +1,213 @@
+// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+/*
+ * Copyright (C) 2020 Arm Ltd.
+ */
+
+/dts-v1/;
+
+#include "sun50i-h616.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+	model = "OrangePi Zero2";
+	compatible = "xunlong,orangepi-zero2", "allwinner,sun50i-h616";
+
+	aliases {
+		ethernet0 = &emac0;
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-0 {
+			function = LED_FUNCTION_POWER;
+			color = <LED_COLOR_ID_RED>;
+			gpios = <&pio 2 12 GPIO_ACTIVE_HIGH>; /* PC12 */
+			default-state = "on";
+		};
+
+		led-1 {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&pio 2 13 GPIO_ACTIVE_HIGH>; /* PC13 */
+		};
+	};
+
+	reg_vcc5v: vcc5v {
+		/* board wide 5V supply directly from the USB-C socket */
+		compatible = "regulator-fixed";
+		regulator-name = "vcc-5v";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+};
+
+&emac0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&ext_rgmii_pins>;
+	phy-mode = "rgmii";
+	phy-handle = <&ext_rgmii_phy>;
+	phy-supply = <&reg_dcdce>;
+	allwinner,rx-delay-ps = <3100>;
+	allwinner,tx-delay-ps = <700>;
+	status = "okay";
+};
+
+&mdio0 {
+	ext_rgmii_phy: ethernet-phy@1 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <1>;
+	};
+};
+
+&mmc0 {
+	vmmc-supply = <&reg_dcdce>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;	/* PF6 */
+	bus-width = <4>;
+	status = "okay";
+};
+
+&r_rsb {
+	status = "okay";
+
+	axp305: pmic@745 {
+		compatible = "x-powers,axp305", "x-powers,axp805",
+			     "x-powers,axp806";
+		interrupt-controller;
+		#interrupt-cells = <1>;
+		reg = <0x745>;
+
+		x-powers,self-working-mode;
+		vina-supply = <&reg_vcc5v>;
+		vinb-supply = <&reg_vcc5v>;
+		vinc-supply = <&reg_vcc5v>;
+		vind-supply = <&reg_vcc5v>;
+		vine-supply = <&reg_vcc5v>;
+		aldoin-supply = <&reg_vcc5v>;
+		bldoin-supply = <&reg_vcc5v>;
+		cldoin-supply = <&reg_vcc5v>;
+
+		regulators {
+			reg_aldo1: aldo1 {
+				regulator-always-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc-sys";
+			};
+
+			reg_aldo2: aldo2 {	/* 3.3V on headers */
+				regulator-always-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc3v3-ext";
+			};
+
+			reg_aldo3: aldo3 {	/* 3.3V on headers */
+				regulator-always-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc3v3-ext2";
+			};
+
+			reg_bldo1: bldo1 {
+				regulator-always-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcc1v8";
+			};
+
+			bldo2 {
+				/* unused */
+			};
+
+			bldo3 {
+				/* unused */
+			};
+
+			bldo4 {
+				/* unused */
+			};
+
+			cldo1 {
+				/* reserved */
+			};
+
+			cldo2 {
+				/* unused */
+			};
+
+			cldo3 {
+				/* unused */
+			};
+
+			reg_dcdca: dcdca {
+				regulator-always-on;
+				regulator-min-microvolt = <810000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-name = "vdd-cpu";
+			};
+
+			reg_dcdcc: dcdcc {
+				regulator-always-on;
+				regulator-min-microvolt = <810000>;
+				regulator-max-microvolt = <990000>;
+				regulator-name = "vdd-gpu-sys";
+			};
+
+			reg_dcdcd: dcdcd {
+				regulator-always-on;
+				regulator-min-microvolt = <1500000>;
+				regulator-max-microvolt = <1500000>;
+				regulator-name = "vdd-dram";
+			};
+
+			reg_dcdce: dcdce {
+				regulator-always-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc-eth-mmc";
+			};
+
+			sw {
+				/* unused */
+			};
+		};
+	};
+};
+
+&pio {
+	vcc-pc-supply = <&reg_aldo1>;
+	vcc-pf-supply = <&reg_aldo1>;
+	vcc-pg-supply = <&reg_bldo1>;
+	vcc-ph-supply = <&reg_aldo1>;
+	vcc-pi-supply = <&reg_aldo1>;
+};
+
+&spi0  {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_pins>, <&spi0_cs0_pin>;
+
+	flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <40000000>;
+	};
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_ph_pins>;
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h616-x96-mate.dts b/arch/arm64/boot/dts/allwinner/sun50i-h616-x96-mate.dts
new file mode 100644
index 000000000000..6619db34714a
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h616-x96-mate.dts
@@ -0,0 +1,177 @@
+// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+/*
+ * Copyright (C) 2021 Arm Ltd.
+ */
+
+/dts-v1/;
+
+#include "sun50i-h616.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+	model = "X96 Mate";
+	compatible = "hechuang,x96-mate", "allwinner,sun50i-h616";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	reg_vcc5v: vcc5v {
+		/* board wide 5V supply directly from the DC input */
+		compatible = "regulator-fixed";
+		regulator-name = "vcc-5v";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+};
+
+&ir {
+	status = "okay";
+};
+
+&mmc0 {
+	vmmc-supply = <&reg_dcdce>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;	/* PF6 */
+	bus-width = <4>;
+	status = "okay";
+};
+
+&mmc2 {
+	vmmc-supply = <&reg_dcdce>;
+	vqmmc-supply = <&reg_bldo1>;
+	bus-width = <8>;
+	non-removable;
+	cap-mmc-hw-reset;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+	status = "okay";
+};
+
+&r_rsb {
+	status = "okay";
+
+	axp305: pmic@745 {
+		compatible = "x-powers,axp305", "x-powers,axp805",
+			     "x-powers,axp806";
+		interrupt-controller;
+		#interrupt-cells = <1>;
+		reg = <0x745>;
+
+		x-powers,self-working-mode;
+		vina-supply = <&reg_vcc5v>;
+		vinb-supply = <&reg_vcc5v>;
+		vinc-supply = <&reg_vcc5v>;
+		vind-supply = <&reg_vcc5v>;
+		vine-supply = <&reg_vcc5v>;
+		aldoin-supply = <&reg_vcc5v>;
+		bldoin-supply = <&reg_vcc5v>;
+		cldoin-supply = <&reg_vcc5v>;
+
+		regulators {
+			reg_aldo1: aldo1 {
+				regulator-always-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc-sys";
+			};
+
+			/* Enabled by the Android BSP */
+			reg_aldo2: aldo2 {
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc3v3-ext";
+				status = "disabled";
+			};
+
+			/* Enabled by the Android BSP */
+			reg_aldo3: aldo3 {
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc3v3-ext2";
+				status = "disabled";
+			};
+
+			reg_bldo1: bldo1 {
+				regulator-always-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcc1v8";
+			};
+
+			/* Enabled by the Android BSP */
+			reg_bldo2: bldo2 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcc1v8-2";
+				status = "disabled";
+			};
+
+			bldo3 {
+				/* unused */
+			};
+
+			bldo4 {
+				/* unused */
+			};
+
+			cldo1 {
+				regulator-min-microvolt = <2500000>;
+				regulator-max-microvolt = <2500000>;
+				regulator-name = "vcc2v5";
+			};
+
+			cldo2 {
+				/* unused */
+			};
+
+			cldo3 {
+				/* unused */
+			};
+
+			reg_dcdca: dcdca {
+				regulator-always-on;
+				regulator-min-microvolt = <810000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-name = "vdd-cpu";
+			};
+
+			reg_dcdcc: dcdcc {
+				regulator-always-on;
+				regulator-min-microvolt = <810000>;
+				regulator-max-microvolt = <990000>;
+				regulator-name = "vdd-gpu-sys";
+			};
+
+			reg_dcdcd: dcdcd {
+				regulator-always-on;
+				regulator-min-microvolt = <1360000>;
+				regulator-max-microvolt = <1360000>;
+				regulator-name = "vdd-dram";
+			};
+
+			reg_dcdce: dcdce {
+				regulator-always-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc-eth-mmc";
+			};
+
+			sw {
+				/* unused */
+			};
+		};
+	};
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_ph_pins>;
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi
new file mode 100644
index 000000000000..622a1f7d1641
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi
@@ -0,0 +1,591 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+// Copyright (C) 2020 Arm Ltd.
+// based on the H6 dtsi, which is:
+//   Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io>
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/sun50i-h616-ccu.h>
+#include <dt-bindings/clock/sun50i-h6-r-ccu.h>
+#include <dt-bindings/clock/sun6i-rtc.h>
+#include <dt-bindings/reset/sun50i-h616-ccu.h>
+#include <dt-bindings/reset/sun50i-h6-r-ccu.h>
+
+/ {
+	interrupt-parent = <&gic>;
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			compatible = "arm,cortex-a53";
+			device_type = "cpu";
+			reg = <0>;
+			enable-method = "psci";
+			clocks = <&ccu CLK_CPUX>;
+		};
+
+		cpu1: cpu@1 {
+			compatible = "arm,cortex-a53";
+			device_type = "cpu";
+			reg = <1>;
+			enable-method = "psci";
+			clocks = <&ccu CLK_CPUX>;
+		};
+
+		cpu2: cpu@2 {
+			compatible = "arm,cortex-a53";
+			device_type = "cpu";
+			reg = <2>;
+			enable-method = "psci";
+			clocks = <&ccu CLK_CPUX>;
+		};
+
+		cpu3: cpu@3 {
+			compatible = "arm,cortex-a53";
+			device_type = "cpu";
+			reg = <3>;
+			enable-method = "psci";
+			clocks = <&ccu CLK_CPUX>;
+		};
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		/*
+		 * 256 KiB reserved for Trusted Firmware-A (BL31).
+		 * This is added by BL31 itself, but some bootloaders fail
+		 * to propagate this into the DTB handed to kernels.
+		 */
+		secmon@40000000 {
+			reg = <0x0 0x40000000 0x0 0x40000>;
+			no-map;
+		};
+	};
+
+	osc24M: osc24M-clk {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <24000000>;
+		clock-output-names = "osc24M";
+	};
+
+	pmu {
+		compatible = "arm,cortex-a53-pmu";
+		interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>;
+	};
+
+	psci {
+		compatible = "arm,psci-0.2";
+		method = "smc";
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		arm,no-tick-in-suspend;
+		interrupts = <GIC_PPI 13
+			(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
+			     <GIC_PPI 14
+			(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
+			     <GIC_PPI 11
+			(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
+			     <GIC_PPI 10
+			(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+	};
+
+	soc {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x0 0x0 0x40000000>;
+
+		syscon: syscon@3000000 {
+			compatible = "allwinner,sun50i-h616-system-control";
+			reg = <0x03000000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			sram_c: sram@28000 {
+				compatible = "mmio-sram";
+				reg = <0x00028000 0x30000>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0 0x00028000 0x30000>;
+			};
+		};
+
+		ccu: clock@3001000 {
+			compatible = "allwinner,sun50i-h616-ccu";
+			reg = <0x03001000 0x1000>;
+			clocks = <&osc24M>, <&rtc CLK_OSC32K>, <&rtc CLK_IOSC>;
+			clock-names = "hosc", "losc", "iosc";
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+		};
+
+		watchdog: watchdog@30090a0 {
+			compatible = "allwinner,sun50i-h616-wdt",
+				     "allwinner,sun6i-a31-wdt";
+			reg = <0x030090a0 0x20>;
+			interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&osc24M>;
+		};
+
+		pio: pinctrl@300b000 {
+			compatible = "allwinner,sun50i-h616-pinctrl";
+			reg = <0x0300b000 0x400>;
+			interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_APB1>, <&osc24M>, <&rtc CLK_OSC32K>;
+			clock-names = "apb", "hosc", "losc";
+			gpio-controller;
+			#gpio-cells = <3>;
+			interrupt-controller;
+			#interrupt-cells = <3>;
+
+			ext_rgmii_pins: rgmii-pins {
+				pins = "PI0", "PI1", "PI2", "PI3", "PI4",
+				       "PI5", "PI7", "PI8", "PI9", "PI10",
+				       "PI11", "PI12", "PI13", "PI14", "PI15",
+				       "PI16";
+				function = "emac0";
+				drive-strength = <40>;
+			};
+
+			i2c0_pins: i2c0-pins {
+				pins = "PI6", "PI7";
+				function = "i2c0";
+			};
+
+			i2c3_ph_pins: i2c3-ph-pins {
+				pins = "PH4", "PH5";
+				function = "i2c3";
+			};
+
+			ir_rx_pin: ir-rx-pin {
+				pins = "PH10";
+				function = "ir_rx";
+			};
+
+			mmc0_pins: mmc0-pins {
+				pins = "PF0", "PF1", "PF2", "PF3",
+				       "PF4", "PF5";
+				function = "mmc0";
+				drive-strength = <30>;
+				bias-pull-up;
+			};
+
+			/omit-if-no-ref/
+			mmc1_pins: mmc1-pins {
+				pins = "PG0", "PG1", "PG2", "PG3",
+				       "PG4", "PG5";
+				function = "mmc1";
+				drive-strength = <30>;
+				bias-pull-up;
+			};
+
+			mmc2_pins: mmc2-pins {
+				pins = "PC0", "PC1", "PC5", "PC6",
+				       "PC8", "PC9", "PC10", "PC11",
+				       "PC13", "PC14", "PC15", "PC16";
+				function = "mmc2";
+				drive-strength = <30>;
+				bias-pull-up;
+			};
+
+			/omit-if-no-ref/
+			spi0_pins: spi0-pins {
+				pins = "PC0", "PC2", "PC4";
+				function = "spi0";
+			};
+
+			/omit-if-no-ref/
+			spi0_cs0_pin: spi0-cs0-pin {
+				pins = "PC3";
+				function = "spi0";
+			};
+
+			/omit-if-no-ref/
+			spi1_pins: spi1-pins {
+				pins = "PH6", "PH7", "PH8";
+				function = "spi1";
+			};
+
+			/omit-if-no-ref/
+			spi1_cs0_pin: spi1-cs0-pin {
+				pins = "PH5";
+				function = "spi1";
+			};
+
+			uart0_ph_pins: uart0-ph-pins {
+				pins = "PH0", "PH1";
+				function = "uart0";
+			};
+
+			/omit-if-no-ref/
+			uart1_pins: uart1-pins {
+				pins = "PG6", "PG7";
+				function = "uart1";
+			};
+
+			/omit-if-no-ref/
+			uart1_rts_cts_pins: uart1-rts-cts-pins {
+				pins = "PG8", "PG9";
+				function = "uart1";
+			};
+		};
+
+		gic: interrupt-controller@3021000 {
+			compatible = "arm,gic-400";
+			reg = <0x03021000 0x1000>,
+			      <0x03022000 0x2000>,
+			      <0x03024000 0x2000>,
+			      <0x03026000 0x2000>;
+			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+			interrupt-controller;
+			#interrupt-cells = <3>;
+		};
+
+		mmc0: mmc@4020000 {
+			compatible = "allwinner,sun50i-h616-mmc",
+				     "allwinner,sun50i-a100-mmc";
+			reg = <0x04020000 0x1000>;
+			clocks = <&ccu CLK_BUS_MMC0>, <&ccu CLK_MMC0>;
+			clock-names = "ahb", "mmc";
+			resets = <&ccu RST_BUS_MMC0>;
+			reset-names = "ahb";
+			interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&mmc0_pins>;
+			status = "disabled";
+			max-frequency = <150000000>;
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			mmc-ddr-3_3v;
+			cap-sdio-irq;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		mmc1: mmc@4021000 {
+			compatible = "allwinner,sun50i-h616-mmc",
+				     "allwinner,sun50i-a100-mmc";
+			reg = <0x04021000 0x1000>;
+			clocks = <&ccu CLK_BUS_MMC1>, <&ccu CLK_MMC1>;
+			clock-names = "ahb", "mmc";
+			resets = <&ccu RST_BUS_MMC1>;
+			reset-names = "ahb";
+			interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&mmc1_pins>;
+			status = "disabled";
+			max-frequency = <150000000>;
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			mmc-ddr-3_3v;
+			cap-sdio-irq;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		mmc2: mmc@4022000 {
+			compatible = "allwinner,sun50i-h616-emmc",
+				     "allwinner,sun50i-a100-emmc";
+			reg = <0x04022000 0x1000>;
+			clocks = <&ccu CLK_BUS_MMC2>, <&ccu CLK_MMC2>;
+			clock-names = "ahb", "mmc";
+			resets = <&ccu RST_BUS_MMC2>;
+			reset-names = "ahb";
+			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&mmc2_pins>;
+			status = "disabled";
+			max-frequency = <150000000>;
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			mmc-ddr-3_3v;
+			cap-sdio-irq;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		uart0: serial@5000000 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x05000000 0x400>;
+			interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&ccu CLK_BUS_UART0>;
+			resets = <&ccu RST_BUS_UART0>;
+			status = "disabled";
+		};
+
+		uart1: serial@5000400 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x05000400 0x400>;
+			interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&ccu CLK_BUS_UART1>;
+			resets = <&ccu RST_BUS_UART1>;
+			status = "disabled";
+		};
+
+		uart2: serial@5000800 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x05000800 0x400>;
+			interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&ccu CLK_BUS_UART2>;
+			resets = <&ccu RST_BUS_UART2>;
+			status = "disabled";
+		};
+
+		uart3: serial@5000c00 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x05000c00 0x400>;
+			interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&ccu CLK_BUS_UART3>;
+			resets = <&ccu RST_BUS_UART3>;
+			status = "disabled";
+		};
+
+		uart4: serial@5001000 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x05001000 0x400>;
+			interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&ccu CLK_BUS_UART4>;
+			resets = <&ccu RST_BUS_UART4>;
+			status = "disabled";
+		};
+
+		uart5: serial@5001400 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x05001400 0x400>;
+			interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&ccu CLK_BUS_UART5>;
+			resets = <&ccu RST_BUS_UART5>;
+			status = "disabled";
+		};
+
+		i2c0: i2c@5002000 {
+			compatible = "allwinner,sun50i-h616-i2c",
+				     "allwinner,sun8i-v536-i2c",
+				     "allwinner,sun6i-a31-i2c";
+			reg = <0x05002000 0x400>;
+			interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_I2C0>;
+			resets = <&ccu RST_BUS_I2C0>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&i2c0_pins>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		i2c1: i2c@5002400 {
+			compatible = "allwinner,sun50i-h616-i2c",
+				     "allwinner,sun8i-v536-i2c",
+				     "allwinner,sun6i-a31-i2c";
+			reg = <0x05002400 0x400>;
+			interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_I2C1>;
+			resets = <&ccu RST_BUS_I2C1>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		i2c2: i2c@5002800 {
+			compatible = "allwinner,sun50i-h616-i2c",
+				     "allwinner,sun8i-v536-i2c",
+				     "allwinner,sun6i-a31-i2c";
+			reg = <0x05002800 0x400>;
+			interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_I2C2>;
+			resets = <&ccu RST_BUS_I2C2>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		i2c3: i2c@5002c00 {
+			compatible = "allwinner,sun50i-h616-i2c",
+				     "allwinner,sun8i-v536-i2c",
+				     "allwinner,sun6i-a31-i2c";
+			reg = <0x05002c00 0x400>;
+			interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_I2C3>;
+			resets = <&ccu RST_BUS_I2C3>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		i2c4: i2c@5003000 {
+			compatible = "allwinner,sun50i-h616-i2c",
+				     "allwinner,sun8i-v536-i2c",
+				     "allwinner,sun6i-a31-i2c";
+			reg = <0x05003000 0x400>;
+			interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_I2C4>;
+			resets = <&ccu RST_BUS_I2C4>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		spi0: spi@5010000 {
+			compatible = "allwinner,sun50i-h616-spi",
+				     "allwinner,sun8i-h3-spi";
+			reg = <0x05010000 0x1000>;
+			interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_SPI0>, <&ccu CLK_SPI0>;
+			clock-names = "ahb", "mod";
+			resets = <&ccu RST_BUS_SPI0>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		spi1: spi@5011000 {
+			compatible = "allwinner,sun50i-h616-spi",
+				     "allwinner,sun8i-h3-spi";
+			reg = <0x05011000 0x1000>;
+			interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_SPI1>, <&ccu CLK_SPI1>;
+			clock-names = "ahb", "mod";
+			resets = <&ccu RST_BUS_SPI1>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		emac0: ethernet@5020000 {
+			compatible = "allwinner,sun50i-h616-emac0",
+				     "allwinner,sun50i-a64-emac";
+			reg = <0x05020000 0x10000>;
+			interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "macirq";
+			clocks = <&ccu CLK_BUS_EMAC0>;
+			clock-names = "stmmaceth";
+			resets = <&ccu RST_BUS_EMAC0>;
+			reset-names = "stmmaceth";
+			syscon = <&syscon>;
+			status = "disabled";
+
+			mdio0: mdio {
+				compatible = "snps,dwmac-mdio";
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+
+		rtc: rtc@7000000 {
+			compatible = "allwinner,sun50i-h616-rtc";
+			reg = <0x07000000 0x400>;
+			interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&r_ccu CLK_R_APB1_RTC>, <&osc24M>,
+				 <&ccu CLK_PLL_SYSTEM_32K>;
+			clock-names = "bus", "hosc",
+				      "pll-32k";
+			#clock-cells = <1>;
+		};
+
+		r_ccu: clock@7010000 {
+			compatible = "allwinner,sun50i-h616-r-ccu";
+			reg = <0x07010000 0x210>;
+			clocks = <&osc24M>, <&rtc CLK_OSC32K>, <&rtc CLK_IOSC>,
+				 <&ccu CLK_PLL_PERIPH0>;
+			clock-names = "hosc", "losc", "iosc", "pll-periph";
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+		};
+
+		r_pio: pinctrl@7022000 {
+			compatible = "allwinner,sun50i-h616-r-pinctrl";
+			reg = <0x07022000 0x400>;
+			clocks = <&r_ccu CLK_R_APB1>, <&osc24M>,
+				 <&rtc CLK_OSC32K>;
+			clock-names = "apb", "hosc", "losc";
+			gpio-controller;
+			#gpio-cells = <3>;
+
+			/omit-if-no-ref/
+			r_i2c_pins: r-i2c-pins {
+				pins = "PL0", "PL1";
+				function = "s_i2c";
+			};
+
+			r_rsb_pins: r-rsb-pins {
+				pins = "PL0", "PL1";
+				function = "s_rsb";
+			};
+		};
+
+		ir: ir@7040000 {
+			compatible = "allwinner,sun50i-h616-ir",
+				     "allwinner,sun6i-a31-ir";
+			reg = <0x07040000 0x400>;
+			interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&r_ccu CLK_R_APB1_IR>,
+				 <&r_ccu CLK_IR>;
+			clock-names = "apb", "ir";
+			resets = <&r_ccu RST_R_APB1_IR>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&ir_rx_pin>;
+			status = "disabled";
+		};
+
+		r_i2c: i2c@7081400 {
+			compatible = "allwinner,sun50i-h616-i2c",
+				     "allwinner,sun8i-v536-i2c",
+				     "allwinner,sun6i-a31-i2c";
+			reg = <0x07081400 0x400>;
+			interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&r_ccu CLK_R_APB2_I2C>;
+			resets = <&r_ccu RST_R_APB2_I2C>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		r_rsb: rsb@7083000 {
+			compatible = "allwinner,sun50i-h616-rsb",
+				     "allwinner,sun8i-a23-rsb";
+			reg = <0x07083000 0x400>;
+			interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&r_ccu CLK_R_APB2_RSB>;
+			clock-frequency = <3000000>;
+			resets = <&r_ccu RST_R_APB2_RSB>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&r_rsb_pins>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+};
diff --git a/arch/arm64/boot/dts/altera/Makefile b/arch/arm64/boot/dts/altera/Makefile
index 4db83fbeb115..1bf0c472f6b4 100644
--- a/arch/arm64/boot/dts/altera/Makefile
+++ b/arch/arm64/boot/dts/altera/Makefile
@@ -1,3 +1,4 @@
 # SPDX-License-Identifier: GPL-2.0-only
 dtb-$(CONFIG_ARCH_INTEL_SOCFPGA) += socfpga_stratix10_socdk.dtb \
-				socfpga_stratix10_socdk_nand.dtb
+				socfpga_stratix10_socdk_nand.dtb \
+				socfpga_stratix10_swvp.dtb
diff --git a/arch/arm64/boot/dts/altera/socfpga_stratix10.dtsi b/arch/arm64/boot/dts/altera/socfpga_stratix10.dtsi
index d301ac0d406b..14c220d87807 100644
--- a/arch/arm64/boot/dts/altera/socfpga_stratix10.dtsi
+++ b/arch/arm64/boot/dts/altera/socfpga_stratix10.dtsi
@@ -77,6 +77,16 @@
 		method = "smc";
 	};
 
+	/* Local timer */
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupts = <1 13 0xf08>,
+			     <1 14 0xf08>,
+			     <1 11 0xf08>,
+			     <1 10 0xf08>;
+		interrupt-parent = <&intc>;
+	};
+
 	intc: interrupt-controller@fffc1000 {
 		compatible = "arm,gic-400", "arm,cortex-a15-gic";
 		#interrupt-cells = <3>;
@@ -87,6 +97,34 @@
 		      <0x0 0xfffc6000 0x0 0x2000>;
 	};
 
+	clocks {
+		cb_intosc_hs_div2_clk: cb-intosc-hs-div2-clk {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+		};
+
+		cb_intosc_ls_clk: cb-intosc-ls-clk {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+		};
+
+		f2s_free_clk: f2s-free-clk {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+		};
+
+		osc1: osc1 {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+		};
+
+		qspi_clk: qspi-clk {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <200000000>;
+		};
+	};
+
 	soc {
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -109,34 +147,6 @@
 			#clock-cells = <1>;
 		};
 
-		clocks {
-			cb_intosc_hs_div2_clk: cb-intosc-hs-div2-clk {
-				#clock-cells = <0>;
-				compatible = "fixed-clock";
-			};
-
-			cb_intosc_ls_clk: cb-intosc-ls-clk {
-				#clock-cells = <0>;
-				compatible = "fixed-clock";
-			};
-
-			f2s_free_clk: f2s-free-clk {
-				#clock-cells = <0>;
-				compatible = "fixed-clock";
-			};
-
-			osc1: osc1 {
-				#clock-cells = <0>;
-				compatible = "fixed-clock";
-			};
-
-			qspi_clk: qspi-clk {
-				#clock-cells = <0>;
-				compatible = "fixed-clock";
-				clock-frequency = <200000000>;
-			};
-		};
-
 		gmac0: ethernet@ff800000 {
 			compatible = "altr,socfpga-stmmac-a10-s10", "snps,dwmac-3.74a", "snps,dwmac";
 			reg = <0xff800000 0x2000>;
@@ -286,7 +296,7 @@
 			status = "disabled";
 		};
 
-		mmc: dwmmc0@ff808000 {
+		mmc: mmc@ff808000 {
 			#address-cells = <1>;
 			#size-cells = <0>;
 			compatible = "altr,socfpga-dw-mshc";
@@ -323,7 +333,7 @@
 			reg = <0xffe00000 0x100000>;
 		};
 
-		pdma: pdma@ffda0000 {
+		pdma: dma-controller@ffda0000 {
 			compatible = "arm,pl330", "arm,primecell";
 			reg = <0xffda0000 0x1000>;
 			interrupts = <0 81 4>,
@@ -336,8 +346,6 @@
 				     <0 88 4>,
 				     <0 89 4>;
 			#dma-cells = <1>;
-			#dma-channels = <8>;
-			#dma-requests = <32>;
 			clocks = <&clkmgr STRATIX10_L4_MAIN_CLK>;
 			clock-names = "apb_pclk";
 			resets = <&rst DMA_RESET>, <&rst DMA_OCP_RESET>;
@@ -406,15 +414,6 @@
 			reg = <0xffd12000 0x228>;
 		};
 
-		/* Local timer */
-		timer {
-			compatible = "arm,armv8-timer";
-			interrupts = <1 13 0xf08>,
-				     <1 14 0xf08>,
-				     <1 11 0xf08>,
-				     <1 10 0xf08>;
-		};
-
 		timer0: timer0@ffc03000 {
 			compatible = "snps,dw-apb-timer";
 			interrupts = <0 113 4>;
@@ -484,6 +483,7 @@
 			resets = <&rst USB0_RESET>, <&rst USB0_OCP_RESET>;
 			reset-names = "dwc2", "dwc2-ecc";
 			clocks = <&clkmgr STRATIX10_USB_CLK>;
+			clock-names = "otg";
 			iommus = <&smmu 6>;
 			status = "disabled";
 		};
@@ -594,7 +594,7 @@
 		};
 
 		qspi: spi@ff8d2000 {
-			compatible = "cdns,qspi-nor";
+			compatible = "intel,socfpga-qspi", "cdns,qspi-nor";
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <0xff8d2000 0x100>,
diff --git a/arch/arm64/boot/dts/altera/socfpga_stratix10_socdk.dts b/arch/arm64/boot/dts/altera/socfpga_stratix10_socdk.dts
index 46e558ab7729..48424e459f12 100644
--- a/arch/arm64/boot/dts/altera/socfpga_stratix10_socdk.dts
+++ b/arch/arm64/boot/dts/altera/socfpga_stratix10_socdk.dts
@@ -7,6 +7,7 @@
 
 / {
 	model = "SoCFPGA Stratix 10 SoCDK";
+	compatible = "altr,socfpga-stratix10-socdk", "altr,socfpga-stratix10";
 
 	aliases {
 		serial0 = &uart0;
@@ -43,7 +44,7 @@
 		reg = <0 0 0 0>;
 	};
 
-	ref_033v: 033-v-ref {
+	ref_033v: regulator-v-ref {
 		compatible = "regulator-fixed";
 		regulator-name = "0.33V";
 		regulator-min-microvolt = <330000>;
@@ -51,12 +52,6 @@
 	};
 
 	soc {
-		clocks {
-			osc1 {
-				clock-frequency = <25000000>;
-			};
-		};
-
 		eccmgr {
 			sdmmca-ecc@ff8c8c00 {
 				compatible = "altr,socfpga-s10-sdmmc-ecc",
@@ -112,6 +107,10 @@
 	bus-width = <4>;
 };
 
+&osc1 {
+	clock-frequency = <25000000>;
+};
+
 &uart0 {
 	status = "okay";
 };
diff --git a/arch/arm64/boot/dts/altera/socfpga_stratix10_socdk_nand.dts b/arch/arm64/boot/dts/altera/socfpga_stratix10_socdk_nand.dts
index f9b4a39683cf..847a7c01f5af 100644
--- a/arch/arm64/boot/dts/altera/socfpga_stratix10_socdk_nand.dts
+++ b/arch/arm64/boot/dts/altera/socfpga_stratix10_socdk_nand.dts
@@ -7,6 +7,7 @@
 
 / {
 	model = "SoCFPGA Stratix 10 SoCDK";
+	compatible = "altr,socfpga-stratix10-socdk", "altr,socfpga-stratix10";
 
 	aliases {
 		serial0 = &uart0;
@@ -43,7 +44,7 @@
 		reg = <0 0 0 0>;
 	};
 
-	ref_033v: 033-v-ref {
+	ref_033v: regulator-v-ref {
 		compatible = "regulator-fixed";
 		regulator-name = "0.33V";
 		regulator-min-microvolt = <330000>;
@@ -51,12 +52,6 @@
 	};
 
 	soc {
-		clocks {
-			osc1 {
-				clock-frequency = <25000000>;
-			};
-		};
-
 		eccmgr {
 			sdmmca-ecc@ff8c8c00 {
 				compatible = "altr,socfpga-s10-sdmmc-ecc",
@@ -119,32 +114,16 @@
 		};
 
 		partition@200000 {
-			label = "env";
-			reg = <0x200000 0x40000>;
-		};
-
-		partition@240000 {
-			label = "dtb";
-			reg = <0x240000 0x40000>;
-		};
-
-		partition@280000 {
-			label = "kernel";
-			reg = <0x280000 0x2000000>;
-		};
-
-		partition@2280000 {
-			label = "misc";
-			reg = <0x2280000 0x2000000>;
-		};
-
-		partition@4280000 {
-			label = "rootfs";
-			reg = <0x4280000 0x3bd80000>;
+			label = "root";
+			reg = <0x200000 0x3fe00000>;
 		};
 	};
 };
 
+&osc1 {
+	clock-frequency = <25000000>;
+};
+
 &uart0 {
 	status = "okay";
 };
diff --git a/arch/arm64/boot/dts/altera/socfpga_stratix10_swvp.dts b/arch/arm64/boot/dts/altera/socfpga_stratix10_swvp.dts
new file mode 100644
index 000000000000..a8db58573954
--- /dev/null
+++ b/arch/arm64/boot/dts/altera/socfpga_stratix10_swvp.dts
@@ -0,0 +1,117 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2022, Intel Corporation
+ */
+
+#include "socfpga_stratix10.dtsi"
+
+/ {
+	model = "SOCFPGA Stratix 10 SWVP";
+	compatible = "altr,socfpga-stratix10-swvp", "altr,socfpga-stratix10";
+
+	aliases {
+		serial0 = &uart0;
+		serial1 = &uart1;
+
+		timer0 = &timer0;
+		timer1 = &timer1;
+		timer2 = &timer2;
+		timer3 = &timer3;
+
+		ethernet0 = &gmac0;
+		ethernet1 = &gmac1;
+		ethernet2 = &gmac2;
+	};
+
+	chosen {
+		stdout-path = "serial1:115200n8";
+		linux,initrd-start = <0x10000000>;
+		linux,initrd-end = <0x125c8324>;
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x80000000>;
+	};
+};
+
+&cpu0 {
+	enable-method = "spin-table";
+	cpu-release-addr = <0x0 0x0000fff8>;
+};
+
+&cpu1 {
+	enable-method = "spin-table";
+	cpu-release-addr = <0x0 0x0000fff8>;
+};
+
+&cpu2 {
+	enable-method = "spin-table";
+	cpu-release-addr = <0x0 0x0000fff8>;
+};
+
+&cpu3 {
+	enable-method = "spin-table";
+	cpu-release-addr = <0x0 0x0000fff8>;
+};
+
+&osc1 {
+	clock-frequency = <25000000>;
+};
+
+&gmac0 {
+	status = "okay";
+	phy-mode = "rgmii";
+	phy-addr = <0xffffffff>;
+	snps,max-mtu = <0x0>;
+};
+
+&gmac1 {
+	status = "okay";
+	phy-mode = "rgmii";
+	phy-addr = <0xffffffff>;
+};
+
+&gmac2 {
+	status = "okay";
+	phy-mode = "rgmii";
+	phy-addr = <0xffffffff>;
+};
+
+&mmc {
+	status = "okay";
+	altr,dw-mshc-ciu-div = <0x3>;
+	altr,dw-mshc-sdr-timing = <0x0 0x3>;
+	cap-sd-highspeed;
+	cap-mmc-highspeed;
+	broken-cd;
+	bus-width = <4>;
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&usb0 {
+	clocks = <&clkmgr STRATIX10_L4_MP_CLK>;
+	status = "okay";
+};
+
+&usb1 {
+	clocks = <&clkmgr STRATIX10_L4_MP_CLK>;
+	status = "okay";
+};
+
+&rst {
+	altr,modrst-offset = <0x20>;
+};
+
+&sysmgr {
+	reg = <0xffd12000 0x1000>;
+	interrupts = <0x0 0x10 0x4>;
+	cpu1-start-addr = <0xffd06230>;
+};
diff --git a/arch/arm64/boot/dts/amd/Makefile b/arch/arm64/boot/dts/amd/Makefile
index 6a6093064a32..68103a8b0ef5 100644
--- a/arch/arm64/boot/dts/amd/Makefile
+++ b/arch/arm64/boot/dts/amd/Makefile
@@ -1,4 +1,2 @@
 # SPDX-License-Identifier: GPL-2.0
-dtb-$(CONFIG_ARCH_SEATTLE) += amd-overdrive.dtb \
-			amd-overdrive-rev-b0.dtb amd-overdrive-rev-b1.dtb \
-			husky.dtb
+dtb-$(CONFIG_ARCH_SEATTLE) += amd-overdrive-rev-b0.dtb amd-overdrive-rev-b1.dtb
diff --git a/arch/arm64/boot/dts/amd/amd-overdrive-rev-b0.dts b/arch/arm64/boot/dts/amd/amd-overdrive-rev-b0.dts
index 8e341be9a399..02bff65e5fd6 100644
--- a/arch/arm64/boot/dts/amd/amd-overdrive-rev-b0.dts
+++ b/arch/arm64/boot/dts/amd/amd-overdrive-rev-b0.dts
@@ -9,6 +9,7 @@
 /dts-v1/;
 
 /include/ "amd-seattle-soc.dtsi"
+/include/ "amd-seattle-cpus.dtsi"
 
 / {
 	model = "AMD Seattle (Rev.B0) Development Board (Overdrive)";
@@ -19,8 +20,8 @@
 	};
 
 	psci {
-		compatible   = "arm,psci-0.2";
-		method       = "smc";
+		compatible = "arm,psci-0.2";
+		method = "smc";
 	};
 };
 
@@ -36,14 +37,6 @@
 	status = "ok";
 };
 
-&gpio2 {
-	status = "ok";
-};
-
-&gpio3 {
-	status = "ok";
-};
-
 &gpio4 {
 	status = "ok";
 };
@@ -79,10 +72,6 @@
 	};
 };
 
-&ipmi_kcs {
-	status = "ok";
-};
-
 &smb0 {
 	/include/ "amd-seattle-xgbe-b.dtsi"
 };
diff --git a/arch/arm64/boot/dts/amd/amd-overdrive-rev-b1.dts b/arch/arm64/boot/dts/amd/amd-overdrive-rev-b1.dts
index 92cef05c6b74..07dab1f1e3c8 100644
--- a/arch/arm64/boot/dts/amd/amd-overdrive-rev-b1.dts
+++ b/arch/arm64/boot/dts/amd/amd-overdrive-rev-b1.dts
@@ -9,6 +9,7 @@
 /dts-v1/;
 
 /include/ "amd-seattle-soc.dtsi"
+/include/ "amd-seattle-cpus.dtsi"
 
 / {
 	model = "AMD Seattle (Rev.B1) Development Board (Overdrive)";
@@ -19,8 +20,8 @@
 	};
 
 	psci {
-		compatible   = "arm,psci-0.2";
-		method       = "smc";
+		compatible = "arm,psci-0.2";
+		method = "smc";
 	};
 };
 
diff --git a/arch/arm64/boot/dts/amd/amd-overdrive.dts b/arch/arm64/boot/dts/amd/amd-overdrive.dts
deleted file mode 100644
index 41b3a6c0993d..000000000000
--- a/arch/arm64/boot/dts/amd/amd-overdrive.dts
+++ /dev/null
@@ -1,66 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * DTS file for AMD Seattle Overdrive Development Board
- *
- * Copyright (C) 2014 Advanced Micro Devices, Inc.
- */
-
-/dts-v1/;
-
-/include/ "amd-seattle-soc.dtsi"
-
-/ {
-	model = "AMD Seattle Development Board (Overdrive)";
-	compatible = "amd,seattle-overdrive", "amd,seattle";
-
-	chosen {
-		stdout-path = &serial0;
-	};
-};
-
-&ccp0 {
-	status = "ok";
-};
-
-&gpio0 {
-	status = "ok";
-};
-
-&gpio1 {
-	status = "ok";
-};
-
-&i2c0 {
-	status = "ok";
-};
-
-&pcie0 {
-	status = "ok";
-};
-
-&spi0 {
-	status = "ok";
-};
-
-&spi1 {
-	status = "ok";
-	sdcard0: sdcard@0 {
-		compatible = "mmc-spi-slot";
-		reg = <0>;
-		spi-max-frequency = <20000000>;
-		voltage-ranges = <3200 3400>;
-		gpios = <&gpio0 7 0>;
-		interrupt-parent = <&gpio0>;
-		interrupts = <7 3>;
-		pl022,hierarchy = <0>;
-		pl022,interface = <0>;
-		pl022,com-mode = <0x0>;
-		pl022,rx-level-trig = <0>;
-		pl022,tx-level-trig = <0>;
-	};
-};
-
-&v2m0 {
-	arm,msi-base-spi = <64>;
-	arm,msi-num-spis = <256>;
-};
diff --git a/arch/arm64/boot/dts/amd/amd-seattle-cpus.dtsi b/arch/arm64/boot/dts/amd/amd-seattle-cpus.dtsi
new file mode 100644
index 000000000000..93688a0b6820
--- /dev/null
+++ b/arch/arm64/boot/dts/amd/amd-seattle-cpus.dtsi
@@ -0,0 +1,224 @@
+// SPDX-License-Identifier: GPL-2.0
+
+/ {
+	cpus {
+		#address-cells = <0x1>;
+		#size-cells = <0x0>;
+
+		cpu-map {
+			cluster0 {
+				core0 {
+					cpu = <&CPU0>;
+				};
+				core1 {
+					cpu = <&CPU1>;
+				};
+			};
+			cluster1 {
+				core0 {
+					cpu = <&CPU2>;
+				};
+				core1 {
+					cpu = <&CPU3>;
+				};
+			};
+			cluster2 {
+				core0 {
+					cpu = <&CPU4>;
+				};
+				core1 {
+					cpu = <&CPU5>;
+				};
+			};
+			cluster3 {
+				core0 {
+					cpu = <&CPU6>;
+				};
+				core1 {
+					cpu = <&CPU7>;
+				};
+			};
+		};
+
+		CPU0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a57";
+			reg = <0x0>;
+			enable-method = "psci";
+
+			i-cache-size = <0xC000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <256>;
+			l2-cache = <&L2_0>;
+
+		};
+
+		CPU1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a57";
+			reg = <0x1>;
+			enable-method = "psci";
+
+			i-cache-size = <0xC000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <256>;
+			l2-cache = <&L2_0>;
+		};
+
+		CPU2: cpu@100 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a57";
+			reg = <0x100>;
+			enable-method = "psci";
+
+			i-cache-size = <0xC000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <256>;
+			l2-cache = <&L2_1>;
+		};
+
+		CPU3: cpu@101 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a57";
+			reg = <0x101>;
+			enable-method = "psci";
+
+			i-cache-size = <0xC000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <256>;
+			l2-cache = <&L2_1>;
+		};
+
+		CPU4: cpu@200 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a57";
+			reg = <0x200>;
+			enable-method = "psci";
+
+			i-cache-size = <0xC000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <256>;
+			l2-cache = <&L2_2>;
+		};
+
+		CPU5: cpu@201 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a57";
+			reg = <0x201>;
+			enable-method = "psci";
+
+			i-cache-size = <0xC000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <256>;
+			l2-cache = <&L2_2>;
+		};
+
+		CPU6: cpu@300 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a57";
+			reg = <0x300>;
+			enable-method = "psci";
+
+			i-cache-size = <0xC000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <256>;
+			l2-cache = <&L2_3>;
+		};
+
+		CPU7: cpu@301 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a57";
+			reg = <0x301>;
+			enable-method = "psci";
+
+			i-cache-size = <0xC000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <256>;
+			l2-cache = <&L2_3>;
+		};
+	};
+
+	L2_0: l2-cache0 {
+		cache-size = <0x100000>;
+		cache-line-size = <64>;
+		cache-sets = <1024>;
+		cache-unified;
+		next-level-cache = <&L3>;
+	};
+
+	L2_1: l2-cache1 {
+		cache-size = <0x100000>;
+		cache-line-size = <64>;
+		cache-sets = <1024>;
+		cache-unified;
+		next-level-cache = <&L3>;
+	};
+
+	L2_2: l2-cache2 {
+		cache-size = <0x100000>;
+		cache-line-size = <64>;
+		cache-sets = <1024>;
+		cache-unified;
+		next-level-cache = <&L3>;
+	};
+
+	L2_3: l2-cache3 {
+		cache-size = <0x100000>;
+		cache-line-size = <64>;
+		cache-sets = <1024>;
+		cache-unified;
+		next-level-cache = <&L3>;
+	};
+
+	L3: l3-cache {
+		cache-level = <3>;
+		cache-size = <0x800000>;
+		cache-line-size = <64>;
+		cache-sets = <8192>;
+		cache-unified;
+	};
+
+	pmu {
+		compatible = "arm,cortex-a57-pmu";
+		interrupts = <0x0 0x7 0x4>,
+			     <0x0 0x8 0x4>,
+			     <0x0 0x9 0x4>,
+			     <0x0 0xa 0x4>,
+			     <0x0 0xb 0x4>,
+			     <0x0 0xc 0x4>,
+			     <0x0 0xd 0x4>,
+			     <0x0 0xe 0x4>;
+		interrupt-affinity = <&CPU0>,
+				     <&CPU1>,
+				     <&CPU2>,
+				     <&CPU3>,
+				     <&CPU4>,
+				     <&CPU5>,
+				     <&CPU6>,
+				     <&CPU7>;
+	};
+};
diff --git a/arch/arm64/boot/dts/amd/amd-seattle-soc.dtsi b/arch/arm64/boot/dts/amd/amd-seattle-soc.dtsi
index b664e7af74eb..690020589d41 100644
--- a/arch/arm64/boot/dts/amd/amd-seattle-soc.dtsi
+++ b/arch/arm64/boot/dts/amd/amd-seattle-soc.dtsi
@@ -38,18 +38,6 @@
 			     <1 10 0xff04>;
 	};
 
-	pmu {
-		compatible = "arm,armv8-pmuv3";
-		interrupts = <0 7 4>,
-			     <0 8 4>,
-			     <0 9 4>,
-			     <0 10 4>,
-			     <0 11 4>,
-			     <0 12 4>,
-			     <0 13 4>,
-			     <0 14 4>;
-	};
-
 	smb0: smb {
 		compatible = "simple-bus";
 		#address-cells = <2>;
@@ -70,6 +58,7 @@
 			reg = <0 0xe0300000 0 0xf0000>;
 			interrupts = <0 355 4>;
 			clocks = <&sataclk_333mhz>;
+			iommus = <&sata0_smmu 0x0 0x1f>;
 			dma-coherent;
 		};
 
@@ -80,6 +69,27 @@
 			reg = <0 0xe0d00000 0 0xf0000>;
 			interrupts = <0 354 4>;
 			clocks = <&sataclk_333mhz>;
+			iommus = <&sata1_smmu 0x0e>,
+				 <&sata1_smmu 0x0f>,
+				 <&sata1_smmu 0x1e>;
+			dma-coherent;
+		};
+
+		sata0_smmu: iommu@e0200000 {
+			compatible = "arm,mmu-401";
+			reg = <0 0xe0200000 0 0x10000>;
+			#global-interrupts = <1>;
+			interrupts = <0 332 4>, <0 332 4>;
+			#iommu-cells = <2>;
+			dma-coherent;
+		};
+
+		sata1_smmu: iommu@e0c00000 {
+			compatible = "arm,mmu-401";
+			reg = <0 0xe0c00000 0 0x10000>;
+			#global-interrupts = <1>;
+			interrupts = <0 331 4>, <0 331 4>;
+			#iommu-cells = <1>;
 			dma-coherent;
 		};
 
@@ -201,6 +211,10 @@
 			reg = <0 0xe0100000 0 0x10000>;
 			interrupts = <0 3 4>;
 			dma-coherent;
+			iommus = <&sata1_smmu 0x00>,
+				 <&sata1_smmu 0x02>,
+				 <&sata1_smmu 0x40>,
+				 <&sata1_smmu 0x42>;
 		};
 
 		pcie0: pcie@f0000000 {
@@ -213,12 +227,22 @@
 			msi-parent = <&v2m0>;
 			reg = <0 0xf0000000 0 0x10000000>;
 
-			interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
+			interrupt-map-mask = <0xff00 0x0 0x0 0x7>;
 			interrupt-map =
-				<0x1000 0x0 0x0 0x1 &gic0 0x0 0x0 0x0 0x120 0x1>,
-				<0x1000 0x0 0x0 0x2 &gic0 0x0 0x0 0x0 0x121 0x1>,
-				<0x1000 0x0 0x0 0x3 &gic0 0x0 0x0 0x0 0x122 0x1>,
-				<0x1000 0x0 0x0 0x4 &gic0 0x0 0x0 0x0 0x123 0x1>;
+				<0x1100 0x0 0x0 0x1 &gic0 0x0 0x0 0x0 0x120 0x1>,
+				<0x1100 0x0 0x0 0x2 &gic0 0x0 0x0 0x0 0x121 0x1>,
+				<0x1100 0x0 0x0 0x3 &gic0 0x0 0x0 0x0 0x122 0x1>,
+				<0x1100 0x0 0x0 0x4 &gic0 0x0 0x0 0x0 0x123 0x1>,
+
+				<0x1200 0x0 0x0 0x1 &gic0 0x0 0x0 0x0 0x124 0x1>,
+				<0x1200 0x0 0x0 0x2 &gic0 0x0 0x0 0x0 0x125 0x1>,
+				<0x1200 0x0 0x0 0x3 &gic0 0x0 0x0 0x0 0x126 0x1>,
+				<0x1200 0x0 0x0 0x4 &gic0 0x0 0x0 0x0 0x127 0x1>,
+
+				<0x1300 0x0 0x0 0x1 &gic0 0x0 0x0 0x0 0x128 0x1>,
+				<0x1300 0x0 0x0 0x2 &gic0 0x0 0x0 0x0 0x129 0x1>,
+				<0x1300 0x0 0x0 0x3 &gic0 0x0 0x0 0x0 0x12a 0x1>,
+				<0x1300 0x0 0x0 0x4 &gic0 0x0 0x0 0x0 0x12b 0x1>;
 
 			dma-coherent;
 			dma-ranges = <0x43000000 0x0 0x0 0x0 0x0 0x100 0x0>;
@@ -227,8 +251,18 @@
 				<0x01000000 0x00 0x00000000 0x00 0xefff0000 0x00 0x00010000>,
 				/* 32-bit MMIO (size=2G) */
 				<0x02000000 0x00 0x40000000 0x00 0x40000000 0x00 0x80000000>,
-				/* 64-bit MMIO (size= 124G) */
+				/* 64-bit MMIO (size= 508G) */
 				<0x03000000 0x01 0x00000000 0x01 0x00000000 0x7f 0x00000000>;
+			iommu-map = <0x0 &pcie_smmu 0x0 0x10000>;
+		};
+
+		pcie_smmu: iommu@e0a00000 {
+			compatible = "arm,mmu-401";
+			reg = <0 0xe0a00000 0 0x10000>;
+			#global-interrupts = <1>;
+			interrupts = <0 333 4>, <0 333 4>;
+			#iommu-cells = <1>;
+			dma-coherent;
 		};
 
 		/* Perf CCN504 PMU */
diff --git a/arch/arm64/boot/dts/amd/amd-seattle-xgbe-b.dtsi b/arch/arm64/boot/dts/amd/amd-seattle-xgbe-b.dtsi
index d97498361ce3..9259e547e2e8 100644
--- a/arch/arm64/boot/dts/amd/amd-seattle-xgbe-b.dtsi
+++ b/arch/arm64/boot/dts/amd/amd-seattle-xgbe-b.dtsi
@@ -55,7 +55,7 @@
 		clocks = <&xgmacclk0_dma_250mhz>, <&xgmacclk0_ptp_250mhz>;
 		clock-names = "dma_clk", "ptp_clk";
 		phy-mode = "xgmii";
-		#stream-id-cells = <16>;
+		iommus = <&xgmac0_smmu 0x00 0x17>; /* 0-7, 16-23 */
 		dma-coherent;
 	};
 
@@ -81,11 +81,11 @@
 		clocks = <&xgmacclk1_dma_250mhz>, <&xgmacclk1_ptp_250mhz>;
 		clock-names = "dma_clk", "ptp_clk";
 		phy-mode = "xgmii";
-		#stream-id-cells = <16>;
+		iommus = <&xgmac1_smmu 0x00 0x17>; /* 0-7, 16-23 */
 		dma-coherent;
 	};
 
-	xgmac0_smmu: smmu@e0600000 {
+	xgmac0_smmu: iommu@e0600000 {
 		 compatible = "arm,mmu-401";
 		 reg = <0 0xe0600000 0 0x10000>;
 		 #global-interrupts = <1>;
@@ -94,14 +94,11 @@
 			       */
 			      <0 336 4>,
 			      <0 336 4>;
-
-		 mmu-masters = <&xgmac0
-			  0  1  2  3  4  5  6  7
-			 16 17 18 19 20 21 22 23
-		 >;
+		#iommu-cells = <2>;
+		dma-coherent;
 	 };
 
-	 xgmac1_smmu: smmu@e0800000 {
+	 xgmac1_smmu: iommu@e0800000 {
 		 compatible = "arm,mmu-401";
 		 reg = <0 0xe0800000 0 0x10000>;
 		 #global-interrupts = <1>;
@@ -110,9 +107,6 @@
 			       */
 			      <0 335 4>,
 			      <0 335 4>;
-
-		 mmu-masters = <&xgmac1
-			  0  1  2  3  4  5  6  7
-			 16 17 18 19 20 21 22 23
-		 >;
+		#iommu-cells = <2>;
+		dma-coherent;
 	 };
diff --git a/arch/arm64/boot/dts/amd/husky.dts b/arch/arm64/boot/dts/amd/husky.dts
deleted file mode 100644
index 7acde34772cb..000000000000
--- a/arch/arm64/boot/dts/amd/husky.dts
+++ /dev/null
@@ -1,84 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * DTS file for AMD/Linaro 96Boards Enterprise Edition Server (Husky) Board
- * Note: Based-on AMD Seattle Rev.B0
- *
- * Copyright (C) 2015 Advanced Micro Devices, Inc.
- */
-
-/dts-v1/;
-
-/include/ "amd-seattle-soc.dtsi"
-
-/ {
-	model = "Linaro 96Boards Enterprise Edition Server (Husky) Board";
-	compatible = "amd,seattle-overdrive", "amd,seattle";
-
-	chosen {
-		stdout-path = &serial0;
-	};
-
-	psci {
-		compatible   = "arm,psci-0.2";
-		method       = "smc";
-	};
-};
-
-&ccp0 {
-	status = "ok";
-	amd,zlib-support = <1>;
-};
-
-/**
- * NOTE: In Rev.B, gpio0 is reserved.
- */
-&gpio1 {
-	status = "ok";
-};
-
-&gpio2 {
-	status = "ok";
-};
-
-&gpio3 {
-	status = "ok";
-};
-
-&gpio4 {
-	status = "ok";
-};
-
-&i2c0 {
-	status = "ok";
-};
-
-&i2c1 {
-	status = "ok";
-};
-
-&pcie0 {
-	status = "ok";
-};
-
-&spi0 {
-	status = "ok";
-};
-
-&spi1 {
-	status = "ok";
-	sdcard0: sdcard@0 {
-		compatible = "mmc-spi-slot";
-		reg = <0>;
-		spi-max-frequency = <20000000>;
-		voltage-ranges = <3200 3400>;
-		pl022,hierarchy = <0>;
-		pl022,interface = <0>;
-		pl022,com-mode = <0x0>;
-		pl022,rx-level-trig = <0>;
-		pl022,tx-level-trig = <0>;
-	};
-};
-
-&smb0 {
-	/include/ "amd-seattle-xgbe-b.dtsi"
-};
diff --git a/arch/arm64/boot/dts/amlogic/Makefile b/arch/arm64/boot/dts/amlogic/Makefile
index 5148cd9e5146..e213aeebb774 100644
--- a/arch/arm64/boot/dts/amlogic/Makefile
+++ b/arch/arm64/boot/dts/amlogic/Makefile
@@ -1,17 +1,20 @@
 # SPDX-License-Identifier: GPL-2.0
-dtb-$(CONFIG_ARCH_MESON) += meson-axg-s400.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-a1-ad401.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-axg-jethome-jethub-j100.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-axg-jethome-jethub-j110-rev-2.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-axg-jethome-jethub-j110-rev-3.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-axg-s400.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-g12a-radxa-zero.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-g12a-sei510.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-g12a-u200.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-g12a-x96-max.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-g12b-a311d-khadas-vim3.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-g12b-gsking-x.dtb
-dtb-$(CONFIG_ARCH_MESON) += meson-g12b-gtking.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-g12b-gtking-pro.dtb
-dtb-$(CONFIG_ARCH_MESON) += meson-g12b-a311d-khadas-vim3.dtb
-dtb-$(CONFIG_ARCH_MESON) += meson-g12b-s922x-khadas-vim3.dtb
-dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-n2.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-g12b-gtking.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-n2-plus.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-g12b-odroid-n2.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-g12b-s922x-khadas-vim3.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-g12b-ugoos-am6.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-kii-pro.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-nanopi-k2.dtb
@@ -19,28 +22,30 @@ dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-nexbox-a95x.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-odroidc2.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-p200.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-p201.dtb
-dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-vega-s95-pro.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-vega-s95-meta.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-vega-s95-pro.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-vega-s95-telos.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-wetek-hub.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxbb-wetek-play2.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s805x-libretech-ac.dtb
-dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905x-hwacom-amazetv.dtb
-dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905x-khadas-vim.dtb
-dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905x-libretech-cc.dtb
-dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905x-libretech-cc-v2.dtb
-dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905x-nexbox-a95x.dtb
-dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905x-p212.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s805x-p241.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-libretech-pc.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-mecool-kii-pro.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-p230.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-p231.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-phicomm-n1.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-sml5442tw.dtb
-dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s805x-p241.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-vero4k-plus.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905w-jethome-jethub-j80.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905w-p281.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905w-tx3-mini.dtb
-dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905d-libretech-pc.dtb
-dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905w-jethome-jethub-j80.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905x-hwacom-amazetv.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905x-khadas-vim.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905x-libretech-cc-v2.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905x-libretech-cc.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905x-nexbox-a95x.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-gxl-s905x-p212.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-gxm-gt1-ultimate.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxm-khadas-vim2.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxm-mecool-kiii-pro.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxm-minix-neo-u9h.dtb
@@ -51,9 +56,14 @@ dtb-$(CONFIG_ARCH_MESON) += meson-gxm-rbox-pro.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxm-s912-libretech-pc.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxm-vega-s96.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-gxm-wetek-core2.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-s4-s805x2-aq222.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-sm1-a95xf3-air-gbit.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-sm1-a95xf3-air.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-sm1-bananapi-m5.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-sm1-h96-max.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-sm1-khadas-vim3l.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-sm1-odroid-c4.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-sm1-odroid-hc4.dtb
 dtb-$(CONFIG_ARCH_MESON) += meson-sm1-sei610.dtb
-dtb-$(CONFIG_ARCH_MESON) += meson-a1-ad401.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-sm1-x96-air-gbit.dtb
+dtb-$(CONFIG_ARCH_MESON) += meson-sm1-x96-air.dtb
diff --git a/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts b/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts
index 52ebe371df26..b2d6ba660914 100644
--- a/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j100.dts
@@ -1,262 +1,29 @@
 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
 /*
- * Copyright (c) 2021 Vyacheslav Bocharov <adeep@lexina.in>
- * Copyright (c) 2020 JetHome
- * Author: Aleksandr Kazantsev <ak@tvip.ru>
- * Author: Alexey Shevelkin <ash@tvip.ru>
+ * Copyright (c) 2022 Vyacheslav Bocharov <adeep@lexina.in>
+ * Copyright (c) 2022 JetHome
  * Author: Vyacheslav Bocharov <adeep@lexina.in>
  */
 
 /dts-v1/;
 
-#include "meson-axg.dtsi"
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/thermal/thermal.h>
+#include "meson-axg-jethome-jethub-j1xx.dtsi"
 
 / {
 	compatible = "jethome,jethub-j100", "amlogic,a113d", "amlogic,meson-axg";
-	model = "JetHome JetHub J100";
-	aliases {
-		serial0 = &uart_AO;   /* Console */
-		serial1 = &uart_AO_B; /* External UART (Wireless Module) */
-		ethernet0 = &ethmac;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
+	model = "JetHome JetHub D1 (J100)";
 
 	/* 1024MB RAM */
 	memory@0 {
 		device_type = "memory";
 		reg = <0x0 0x0 0x0 0x40000000>;
 	};
-
-	reserved-memory {
-		linux,cma {
-			size = <0x0 0x400000>;
-		};
-	};
-
-	emmc_pwrseq: emmc-pwrseq {
-		compatible = "mmc-pwrseq-emmc";
-		reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
-	};
-
-	vcc_3v3: regulator-vcc_3v3 {
-		compatible = "regulator-fixed";
-		regulator-name = "VCC_3V3";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		vin-supply = <&vddao_3v3>;
-		regulator-always-on;
-	};
-
-	vcc_5v: regulator-vcc_5v {
-		compatible = "regulator-fixed";
-		regulator-name = "VCC5V";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-		regulator-always-on;
-	};
-
-	vddao_3v3: regulator-vddao_3v3 {
-		compatible = "regulator-fixed";
-		regulator-name = "VDDAO_3V3";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		vin-supply = <&vcc_5v>;
-		regulator-always-on;
-	};
-
-	vddio_ao18: regulator-vddio_ao18 {
-		compatible = "regulator-fixed";
-		regulator-name = "VDDIO_AO18";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <1800000>;
-		vin-supply = <&vddao_3v3>;
-		regulator-always-on;
-	};
-
-	vddio_boot: regulator-vddio_boot {
-		compatible = "regulator-fixed";
-		regulator-name = "VDDIO_BOOT";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <1800000>;
-		vin-supply = <&vddao_3v3>;
-		regulator-always-on;
-	};
-
-	usb_pwr: regulator-usb_pwr {
-		compatible = "regulator-fixed";
-		regulator-name = "USB_PWR";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-		vin-supply = <&vcc_5v>;
-		regulator-always-on;
-	};
-
-	sdio_pwrseq: sdio-pwrseq {
-		compatible = "mmc-pwrseq-simple";
-		reset-gpios = <&gpio GPIOX_7 GPIO_ACTIVE_LOW>;
-		clocks = <&wifi32k>;
-		clock-names = "ext_clock";
-	};
-
-	wifi32k: wifi32k {
-		compatible = "pwm-clock";
-		#clock-cells = <0>;
-		clock-frequency = <32768>;
-		pwms = <&pwm_ab 0 30518 0>; /* PWM_A at 32.768KHz */
-	};
-
-	thermal-zones {
-		cpu_thermal: cpu-thermal {
-			polling-delay-passive = <250>;
-			polling-delay = <1000>;
-			thermal-sensors = <&scpi_sensors 0>;
-			trips {
-				cpu_passive: cpu-passive {
-					temperature = <70000>; /* millicelsius */
-					hysteresis = <2000>; /* millicelsius */
-					type = "passive";
-				};
-
-				cpu_hot: cpu-hot {
-					temperature = <80000>; /* millicelsius */
-					hysteresis = <2000>; /* millicelsius */
-					type = "hot";
-				};
-
-				cpu_critical: cpu-critical {
-					temperature = <100000>; /* millicelsius */
-					hysteresis = <2000>; /* millicelsius */
-					type = "critical";
-				};
-			};
-		};
-
-		cpu_cooling_maps: cooling-maps {
-			map0 {
-				trip = <&cpu_passive>;
-				cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-						<&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-						<&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-						<&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
-			};
-
-			map1 {
-				trip = <&cpu_hot>;
-				cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-						<&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-						<&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
-						<&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
-			};
-		};
-	};
-
-	onewire {
-		compatible = "w1-gpio";
-		gpios = <&gpio GPIOA_14 GPIO_ACTIVE_HIGH>;
-		#gpio-cells = <1>;
-	};
-};
-
-&efuse {
-	sn: sn@32 {
-		reg = <0x32 0x20>;
-	};
-
-	eth_mac: eth_mac@0 {
-		reg = <0x0 0x6>;
-	};
-
-	bt_mac: bt_mac@6 {
-		reg = <0x6 0x6>;
-	};
-
-	wifi_mac: wifi_mac@c {
-		reg = <0xc 0x6>;
-	};
-
-	bid: bid@12 {
-		reg = <0x12 0x20>;
-	};
 };
 
-&ethmac {
-	status = "okay";
-	pinctrl-0 = <&eth_rmii_x_pins>;
-	pinctrl-names = "default";
-	phy-handle = <&eth_phy0>;
-	phy-mode = "rmii";
-
-	mdio {
-		compatible = "snps,dwmac-mdio";
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		/* ICPlus IP101A/G Ethernet PHY (vendor_id=0x0243, model_id=0x0c54) */
-		eth_phy0: ethernet-phy@0 {
-			/* compatible = "ethernet-phy-id0243.0c54";*/
-			max-speed = <100>;
-			reg = <0>;
-
-			reset-assert-us = <10000>;
-			reset-deassert-us = <10000>;
-			reset-gpios = <&gpio GPIOZ_5 GPIO_ACTIVE_LOW>;
-		};
-	};
-};
-
-/* Internal I2C bus (on CPU module) */
-&i2c1 {
-	status = "okay";
-	pinctrl-0 = <&i2c1_z_pins>;
-	pinctrl-names = "default";
-
-	/* RTC */
-	pcf8563: pcf8563@51 {
-		compatible = "nxp,pcf8563";
-		reg = <0x51>;
-		status = "okay";
-	};
-};
-
-/* Peripheral I2C bus (on motherboard) */
-&i2c_AO {
-	status = "okay";
-	pinctrl-0 = <&i2c_ao_sck_10_pins>, <&i2c_ao_sda_11_pins>;
-	pinctrl-names = "default";
-};
-
-&pwm_ab {
-	status = "okay";
-	pinctrl-0 = <&pwm_a_x20_pins>;
-	pinctrl-names = "default";
-};
 
 /* wifi module */
 &sd_emmc_b {
-	status = "okay";
-	#address-cells = <1>;
-	#size-cells = <0>;
-
-	pinctrl-0 = <&sdio_pins>;
-	pinctrl-1 = <&sdio_clk_gate_pins>;
-	pinctrl-names = "default", "clk-gate";
-
-	bus-width = <4>;
-	cap-sd-highspeed;
-	sd-uhs-sdr104;
-	max-frequency = <200000000>;
 	non-removable;
-	disable-wp;
-
-	mmc-pwrseq = <&sdio_pwrseq>;
-
-	vmmc-supply = <&vddao_3v3>;
-	vqmmc-supply = <&vddio_boot>;
 
 	brcmf: wifi@1 {
 		reg = <1>;
@@ -264,99 +31,10 @@
 	};
 };
 
-/* emmc storage */
-&sd_emmc_c {
-	status = "okay";
-	pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
-	pinctrl-1 = <&emmc_clk_gate_pins>;
-	pinctrl-names = "default", "clk-gate";
-
-	bus-width = <8>;
-	cap-mmc-highspeed;
-	max-frequency = <200000000>;
-	non-removable;
-	disable-wp;
-	mmc-ddr-1_8v;
-	mmc-hs200-1_8v;
-
-	mmc-pwrseq = <&emmc_pwrseq>;
-
-	vmmc-supply = <&vcc_3v3>;
-	vqmmc-supply = <&vddio_boot>;
-};
-
 /* UART Bluetooth */
 &uart_B {
-	status = "okay";
-	pinctrl-0 = <&uart_b_z_pins>, <&uart_b_z_cts_rts_pins>;
-	pinctrl-names = "default";
-	uart-has-rtscts;
-
 	bluetooth {
 		compatible = "brcm,bcm43438-bt";
 		shutdown-gpios = <&gpio GPIOZ_7 GPIO_ACTIVE_HIGH>;
 	};
 };
-
-/* UART Console */
-&uart_AO {
-	status = "okay";
-	pinctrl-0 = <&uart_ao_a_pins>;
-	pinctrl-names = "default";
-};
-
-/* UART Wireless module */
-&uart_AO_B {
-	status = "okay";
-	pinctrl-0 = <&uart_ao_b_pins>;
-	pinctrl-names = "default";
-};
-
-&usb {
-	status = "okay";
-	phy-supply = <&usb_pwr>;
-};
-
-&spicc1 {
-	status = "okay";
-	pinctrl-0 = <&spi1_x_pins>, <&spi1_ss0_x_pins>;
-	pinctrl-names = "default";
-};
-
-&gpio {
-	gpio-line-names =
-		"", "", "", "", "", // 0 - 4
-		"", "", "", "", "", // 5 - 9
-		"UserButton", "", "", "", "", // 10 - 14
-		"", "", "", "", "", // 15 - 19
-		"", "", "", "", "", // 20 - 24
-		"", "LedRed", "LedGreen", "Output3", "Output2", // 25 - 29
-		"Output1", "", "", "", "", // 30 - 34
-		"", "ZigBeeBOOT", "", "", "", // 35 - 39
-		"1Wire", "ZigBeeRESET", "", "Input4", "Input3", // 40 - 44
-		"Input2", "Input1", "", "", "", // 45 - 49
-		"", "", "", "", "", // 50 - 54
-		"", "", "", "", "", // 55 - 59
-		"", "", "", "", "", // 60 - 64
-		"", "", "", "", "", // 65 - 69
-		"", "", "", "", "", // 70 - 74
-		"", "", "", "", "", // 75 - 79
-		"", "", "", "", "", // 80 - 84
-		"", ""; // 85-86
-};
-
-&cpu0 {
-	#cooling-cells = <2>;
-};
-
-&cpu1 {
-	#cooling-cells = <2>;
-};
-
-&cpu2 {
-	#cooling-cells = <2>;
-};
-
-&cpu3 {
-	#cooling-cells = <2>;
-};
diff --git a/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j110-rev-2.dts b/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j110-rev-2.dts
new file mode 100644
index 000000000000..0062667c4f65
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j110-rev-2.dts
@@ -0,0 +1,37 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2022 Vyacheslav Bocharov <adeep@lexina.in>
+ * Copyright (c) 2022 JetHome
+ * Author: Vyacheslav Bocharov <adeep@lexina.in>
+ */
+
+/dts-v1/;
+
+#include "meson-axg-jethome-jethub-j1xx.dtsi"
+
+/ {
+	compatible = "jethome,jethub-j110", "amlogic,a113d", "amlogic,meson-axg";
+	model = "JetHome JetHub D1p (J110) HW rev.2";
+
+	/* 2GiB or 4GiB RAM */
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x80000000>;
+	};
+};
+
+
+/* wifi module */
+&sd_emmc_b {
+	broken-cd;/* cd-gpios = <&gpio_ao GPIOAO_3 GPIO_ACTIVE_LOW>;*/
+};
+
+/* UART Bluetooth */
+&uart_B {
+	bluetooth {
+		compatible = "realtek,rtl8822cs-bt";
+		enable-gpios  = <&gpio GPIOZ_7 GPIO_ACTIVE_HIGH>;
+		host-wake-gpios = <&gpio GPIOZ_8 GPIO_ACTIVE_HIGH>;
+		device-wake-gpios = <&gpio GPIOZ_6 GPIO_ACTIVE_HIGH>;
+	};
+};
diff --git a/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j110-rev-3.dts b/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j110-rev-3.dts
new file mode 100644
index 000000000000..c2d22b00c1cd
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j110-rev-3.dts
@@ -0,0 +1,27 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2022 Vyacheslav Bocharov <adeep@lexina.in>
+ * Copyright (c) 2022 JetHome
+ * Author: Vyacheslav Bocharov <adeep@lexina.in>
+ */
+
+/dts-v1/;
+
+#include "meson-axg-jethome-jethub-j1xx.dtsi"
+
+/ {
+	compatible = "jethome,jethub-j110", "amlogic,a113d", "amlogic,meson-axg";
+	model = "JetHome JetHub D1p (J110) Hw rev.3";
+
+	/* 2GiB or 4GiB RAM */
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x80000000>;
+	};
+};
+
+
+/* wifi module */
+&sd_emmc_b {
+	broken-cd;/* cd-gpios = <&gpio_ao GPIOAO_3 GPIO_ACTIVE_LOW>;*/
+};
diff --git a/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j1xx.dtsi b/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j1xx.dtsi
new file mode 100644
index 000000000000..5836b0030931
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-axg-jethome-jethub-j1xx.dtsi
@@ -0,0 +1,351 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2022 Vyacheslav Bocharov <adeep@lexina.in>
+ * Copyright (c) 2022 JetHome
+ * Author: Vyacheslav Bocharov <adeep@lexina.in>
+ * Author: Aleksandr Kazantsev <ak@tvip.ru>
+ * Author: Alexey Shevelkin <ash@tvip.ru>
+ */
+
+/dts-v1/;
+
+#include "meson-axg.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/thermal/thermal.h>
+
+/ {
+	aliases {
+		serial0 = &uart_AO;   /* Console */
+		serial2 = &uart_AO_B; /* External UART (Wireless Module) */
+		ethernet0 = &ethmac;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	reserved-memory {
+		linux,cma {
+			size = <0x0 0x400000>;
+		};
+	};
+
+	emmc_pwrseq: emmc-pwrseq {
+		compatible = "mmc-pwrseq-emmc";
+		reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
+	};
+
+	vcc_3v3: regulator-vcc_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vddao_3v3>;
+		regulator-always-on;
+	};
+
+	vcc_5v: regulator-vcc_5v {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+
+	vddao_3v3: regulator-vddao_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDAO_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc_5v>;
+		regulator-always-on;
+	};
+
+	vddio_ao18: regulator-vddio_ao18 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDIO_AO18";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vddao_3v3>;
+		regulator-always-on;
+	};
+
+	vddio_boot: regulator-vddio_boot {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDIO_BOOT";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vddao_3v3>;
+		regulator-always-on;
+	};
+
+	vccq_1v8: regulator-vccq_1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCCQ_1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vddao_3v3>;
+		regulator-always-on;
+	};
+
+	usb_pwr: regulator-usb_pwr {
+		compatible = "regulator-fixed";
+		regulator-name = "USB_PWR";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc_5v>;
+		regulator-always-on;
+	};
+
+	sdio_pwrseq: sdio-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&gpio GPIOX_7 GPIO_ACTIVE_LOW>;
+		clocks = <&wifi32k>;
+		clock-names = "ext_clock";
+	};
+
+	wifi32k: wifi32k {
+		compatible = "pwm-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		pwms = <&pwm_ab 0 30518 0>; /* PWM_A at 32.768KHz */
+	};
+
+	thermal-zones {
+		cpu_thermal: cpu-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+			thermal-sensors = <&scpi_sensors 0>;
+			trips {
+				cpu_passive: cpu-passive {
+					temperature = <70000>; /* millicelsius */
+					hysteresis = <2000>; /* millicelsius */
+					type = "passive";
+				};
+
+				cpu_hot: cpu-hot {
+					temperature = <80000>; /* millicelsius */
+					hysteresis = <2000>; /* millicelsius */
+					type = "hot";
+				};
+
+				cpu_critical: cpu-critical {
+					temperature = <100000>; /* millicelsius */
+					hysteresis = <2000>; /* millicelsius */
+					type = "critical";
+				};
+			};
+
+			cpu_cooling_maps: cooling-maps {
+				map0 {
+					trip = <&cpu_passive>;
+					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							<&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							<&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							<&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+
+				map1 {
+					trip = <&cpu_hot>;
+					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							<&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							<&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							<&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+	};
+
+	onewire {
+		compatible = "w1-gpio";
+		gpios = <&gpio GPIOA_14 GPIO_ACTIVE_HIGH>;
+		#gpio-cells = <1>;
+	};
+};
+
+&efuse {
+	sn: sn@32 {
+		reg = <0x32 0x20>;
+	};
+
+	eth_mac: eth_mac@0 {
+		reg = <0x0 0x6>;
+	};
+
+	bt_mac: bt_mac@6 {
+		reg = <0x6 0x6>;
+	};
+
+	wifi_mac: wifi_mac@c {
+		reg = <0xc 0x6>;
+	};
+
+	bid: bid@12 {
+		reg = <0x12 0x20>;
+	};
+};
+
+&ethmac {
+	status = "okay";
+	pinctrl-0 = <&eth_rmii_x_pins>;
+	pinctrl-names = "default";
+	phy-handle = <&eth_phy0>;
+	phy-mode = "rmii";
+
+	mdio {
+		compatible = "snps,dwmac-mdio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* ICPlus IP101A/G Ethernet PHY (vendor_id=0x0243, model_id=0x0c54) */
+		eth_phy0: ethernet-phy@0 {
+			/* compatible = "ethernet-phy-id0243.0c54";*/
+			max-speed = <100>;
+			reg = <0>;
+
+			reset-assert-us = <10000>;
+			reset-deassert-us = <10000>;
+			reset-gpios = <&gpio GPIOZ_5 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+/* Internal I2C bus (on CPU module) */
+&i2c1 {
+	status = "okay";
+	pinctrl-0 = <&i2c1_z_pins>;
+	pinctrl-names = "default";
+
+	/* RTC */
+	pcf8563: pcf8563@51 {
+		compatible = "nxp,pcf8563";
+		reg = <0x51>;
+		status = "okay";
+	};
+};
+
+/* Peripheral I2C bus (on motherboard) */
+&i2c_AO {
+	status = "okay";
+	pinctrl-0 = <&i2c_ao_sck_10_pins>, <&i2c_ao_sda_11_pins>;
+	pinctrl-names = "default";
+};
+
+&pwm_ab {
+	status = "okay";
+	pinctrl-0 = <&pwm_a_x20_pins>;
+	pinctrl-names = "default";
+};
+
+/* wifi module */
+&sd_emmc_b {
+	status = "okay";
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	pinctrl-0 = <&sdio_pins>;
+	pinctrl-1 = <&sdio_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <4>;
+	cap-sd-highspeed;
+	max-frequency = <50000000>;
+	disable-wp;
+
+	mmc-pwrseq = <&sdio_pwrseq>;
+
+	vmmc-supply = <&vddao_3v3>;
+	vqmmc-supply = <&vddio_boot>;
+};
+
+/* emmc storage */
+&sd_emmc_c {
+	status = "okay";
+	pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
+	pinctrl-1 = <&emmc_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <8>;
+	cap-mmc-highspeed;
+	max-frequency = <200000000>;
+	non-removable;
+	disable-wp;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+
+	mmc-pwrseq = <&emmc_pwrseq>;
+
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&vccq_1v8>;
+};
+
+/* UART Bluetooth */
+&uart_B {
+	status = "okay";
+	pinctrl-0 = <&uart_b_z_pins>, <&uart_b_z_cts_rts_pins>;
+	pinctrl-names = "default";
+	uart-has-rtscts;
+};
+
+/* UART Console */
+&uart_AO {
+	status = "okay";
+	pinctrl-0 = <&uart_ao_a_pins>;
+	pinctrl-names = "default";
+};
+
+/* UART Wireless module */
+&uart_AO_B {
+	status = "okay";
+	pinctrl-0 = <&uart_ao_b_pins>;
+	pinctrl-names = "default";
+};
+
+&usb {
+	status = "okay";
+	phy-supply = <&usb_pwr>;
+};
+
+&spicc1 {
+	status = "okay";
+	pinctrl-0 = <&spi1_x_pins>, <&spi1_ss0_x_pins>;
+	pinctrl-names = "default";
+};
+
+&gpio {
+	gpio-line-names =
+		"", "", "", "", "", // 0 - 4
+		"", "", "", "", "", // 5 - 9
+		"UserButton", "", "", "", "", // 10 - 14
+		"", "", "", "", "", // 15 - 19
+		"", "", "", "", "", // 20 - 24
+		"", "LedRed", "LedGreen", "Output3", "Output2", // 25 - 29
+		"Output1", "", "", "", "", // 30 - 34
+		"", "ZigBeeBOOT", "", "", "", // 35 - 39
+		"1Wire", "ZigBeeRESET", "", "Input4", "Input3", // 40 - 44
+		"Input2", "Input1", "", "", "", // 45 - 49
+		"", "", "", "", "", // 50 - 54
+		"", "", "", "", "", // 55 - 59
+		"", "", "", "", "", // 60 - 64
+		"", "", "", "", "", // 65 - 69
+		"", "", "", "", "", // 70 - 74
+		"", "", "", "", "", // 75 - 79
+		"", "", "", "", "", // 80 - 84
+		"", ""; // 85-86
+};
+
+&cpu0 {
+	#cooling-cells = <2>;
+};
+
+&cpu1 {
+	#cooling-cells = <2>;
+};
+
+&cpu2 {
+	#cooling-cells = <2>;
+};
+
+&cpu3 {
+	#cooling-cells = <2>;
+};
diff --git a/arch/arm64/boot/dts/amlogic/meson-axg.dtsi b/arch/arm64/boot/dts/amlogic/meson-axg.dtsi
index 3f5254eeb47b..04f797b5a012 100644
--- a/arch/arm64/boot/dts/amlogic/meson-axg.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-axg.dtsi
@@ -1535,7 +1535,7 @@
 
 			sysctrl_AO: sys-ctrl@0 {
 				compatible = "amlogic,meson-axg-ao-sysctrl", "simple-mfd", "syscon";
-				reg =  <0x0 0x0 0x0 0x100>;
+				reg = <0x0 0x0 0x0 0x100>;
 
 				clkc_AO: clock-controller {
 					compatible = "amlogic,meson-axg-aoclkc";
diff --git a/arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi b/arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi
index 00c6f53290d4..45947c1031c4 100644
--- a/arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-g12-common.dtsi
@@ -58,7 +58,7 @@
 		secure-monitor = <&sm>;
 	};
 
-	gpu_opp_table: gpu-opp-table {
+	gpu_opp_table: opp-table-gpu {
 		compatible = "operating-points-v2";
 
 		opp-124999998 {
@@ -107,6 +107,12 @@
 			no-map;
 		};
 
+		/* 32 MiB reserved for ARM Trusted Firmware (BL32) */
+		secmon_reserved_bl32: secmon@5300000 {
+			reg = <0x0 0x05300000 0x0 0x2000000>;
+			no-map;
+		};
+
 		linux,cma {
 			compatible = "shared-dma-pool";
 			reusable;
@@ -159,61 +165,6 @@
 			status = "disabled";
 		};
 
-		thermal-zones {
-			cpu_thermal: cpu-thermal {
-				polling-delay = <1000>;
-				polling-delay-passive = <100>;
-				thermal-sensors = <&cpu_temp>;
-
-				trips {
-					cpu_passive: cpu-passive {
-						temperature = <85000>; /* millicelsius */
-						hysteresis = <2000>; /* millicelsius */
-						type = "passive";
-					};
-
-					cpu_hot: cpu-hot {
-						temperature = <95000>; /* millicelsius */
-						hysteresis = <2000>; /* millicelsius */
-						type = "hot";
-					};
-
-					cpu_critical: cpu-critical {
-						temperature = <110000>; /* millicelsius */
-						hysteresis = <2000>; /* millicelsius */
-						type = "critical";
-					};
-				};
-			};
-
-			ddr_thermal: ddr-thermal {
-				polling-delay = <1000>;
-				polling-delay-passive = <100>;
-				thermal-sensors = <&ddr_temp>;
-
-				trips {
-					ddr_passive: ddr-passive {
-						temperature = <85000>; /* millicelsius */
-						hysteresis = <2000>; /* millicelsius */
-						type = "passive";
-					};
-
-					ddr_critical: ddr-critical {
-						temperature = <110000>; /* millicelsius */
-						hysteresis = <2000>; /* millicelsius */
-						type = "critical";
-					};
-				};
-
-				cooling-maps {
-					map {
-						trip = <&ddr_passive>;
-						cooling-device = <&mali THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
-					};
-				};
-			};
-		};
-
 		ethmac: ethernet@ff3f0000 {
 			compatible = "amlogic,meson-g12a-dwmac",
 				     "snps,dwmac-3.70a",
@@ -894,6 +845,22 @@
 						};
 					};
 
+					pwm_f_z_pins: pwm-f-z {
+						mux {
+							groups = "pwm_f_z";
+							function = "pwm_f";
+							bias-disable;
+						};
+					};
+
+					pwm_f_a_pins: pwm-f-a {
+						mux {
+							groups = "pwm_f_a";
+							function = "pwm_f";
+							bias-disable;
+						};
+					};
+
 					pwm_f_x_pins: pwm-f-x {
 						mux {
 							groups = "pwm_f_x";
@@ -1936,6 +1903,33 @@
 						};
 					};
 
+					uart_ao_b_2_3_pins: uart-ao-b-2-3 {
+						mux {
+							groups = "uart_ao_b_tx_2",
+								 "uart_ao_b_rx_3";
+							function = "uart_ao_b";
+							bias-disable;
+						};
+					};
+
+					uart_ao_b_8_9_pins: uart-ao-b-8-9 {
+						mux {
+							groups = "uart_ao_b_tx_8",
+								 "uart_ao_b_rx_9";
+							function = "uart_ao_b";
+							bias-disable;
+						};
+					};
+
+					uart_ao_b_cts_rts_pins: uart-ao-b-cts-rts {
+						mux {
+							groups = "uart_ao_b_cts",
+								 "uart_ao_b_rts";
+							function = "uart_ao_b";
+							bias-disable;
+						};
+					};
+
 					pwm_a_e_pins: pwm-a-e {
 						mux {
 							groups = "pwm_a_e";
@@ -2415,6 +2409,61 @@
 		};
 	};
 
+	thermal-zones {
+		cpu_thermal: cpu-thermal {
+			polling-delay = <1000>;
+			polling-delay-passive = <100>;
+			thermal-sensors = <&cpu_temp>;
+
+			trips {
+				cpu_passive: cpu-passive {
+					temperature = <85000>; /* millicelsius */
+					hysteresis = <2000>; /* millicelsius */
+					type = "passive";
+				};
+
+				cpu_hot: cpu-hot {
+					temperature = <95000>; /* millicelsius */
+					hysteresis = <2000>; /* millicelsius */
+					type = "hot";
+				};
+
+				cpu_critical: cpu-critical {
+					temperature = <110000>; /* millicelsius */
+					hysteresis = <2000>; /* millicelsius */
+					type = "critical";
+				};
+			};
+		};
+
+		ddr_thermal: ddr-thermal {
+			polling-delay = <1000>;
+			polling-delay-passive = <100>;
+			thermal-sensors = <&ddr_temp>;
+
+			trips {
+				ddr_passive: ddr-passive {
+					temperature = <85000>; /* millicelsius */
+					hysteresis = <2000>; /* millicelsius */
+					type = "passive";
+				};
+
+				ddr_critical: ddr-critical {
+					temperature = <110000>; /* millicelsius */
+					hysteresis = <2000>; /* millicelsius */
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				map {
+					trip = <&ddr_passive>;
+					cooling-device = <&mali THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+	};
+
 	timer {
 		compatible = "arm,armv8-timer";
 		interrupts = <GIC_PPI 13
diff --git a/arch/arm64/boot/dts/amlogic/meson-g12a-sei510.dts b/arch/arm64/boot/dts/amlogic/meson-g12a-sei510.dts
index d8838dde0f0f..4fb31c2ba31c 100644
--- a/arch/arm64/boot/dts/amlogic/meson-g12a-sei510.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-g12a-sei510.dts
@@ -157,14 +157,6 @@
 		regulator-always-on;
 	};
 
-	reserved-memory {
-		/* TEE Reserved Memory */
-		bl32_reserved: bl32@5000000 {
-			reg = <0x0 0x05300000 0x0 0x2000000>;
-			no-map;
-		};
-	};
-
 	sdio_pwrseq: sdio-pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm64/boot/dts/amlogic/meson-g12a-x96-max.dts b/arch/arm64/boot/dts/amlogic/meson-g12a-x96-max.dts
index b4e86196e346..b2bb94981838 100644
--- a/arch/arm64/boot/dts/amlogic/meson-g12a-x96-max.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-g12a-x96-max.dts
@@ -111,7 +111,6 @@
 		vin-supply = <&dc_in>;
 
 		gpio = <&gpio GPIOH_8 GPIO_OPEN_DRAIN>;
-		enable-active-low;
 	};
 
 	vddao_1v8: regulator-vddao_1v8 {
diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-a311d.dtsi b/arch/arm64/boot/dts/amlogic/meson-g12b-a311d.dtsi
index d61f43052a34..8e9ad1e51d66 100644
--- a/arch/arm64/boot/dts/amlogic/meson-g12b-a311d.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-g12b-a311d.dtsi
@@ -11,26 +11,6 @@
 		compatible = "operating-points-v2";
 		opp-shared;
 
-		opp-100000000 {
-			opp-hz = /bits/ 64 <100000000>;
-			opp-microvolt = <731000>;
-		};
-
-		opp-250000000 {
-			opp-hz = /bits/ 64 <250000000>;
-			opp-microvolt = <731000>;
-		};
-
-		opp-500000000 {
-			opp-hz = /bits/ 64 <500000000>;
-			opp-microvolt = <731000>;
-		};
-
-		opp-667000000 {
-			opp-hz = /bits/ 64 <667000000>;
-			opp-microvolt = <731000>;
-		};
-
 		opp-1000000000 {
 			opp-hz = /bits/ 64 <1000000000>;
 			opp-microvolt = <761000>;
@@ -71,26 +51,6 @@
 		compatible = "operating-points-v2";
 		opp-shared;
 
-		opp-100000000 {
-			opp-hz = /bits/ 64 <100000000>;
-			opp-microvolt = <731000>;
-		};
-
-		opp-250000000 {
-			opp-hz = /bits/ 64 <250000000>;
-			opp-microvolt = <731000>;
-		};
-
-		opp-500000000 {
-			opp-hz = /bits/ 64 <500000000>;
-			opp-microvolt = <731000>;
-		};
-
-		opp-667000000 {
-			opp-hz = /bits/ 64 <667000000>;
-			opp-microvolt = <731000>;
-		};
-
 		opp-1000000000 {
 			opp-hz = /bits/ 64 <1000000000>;
 			opp-microvolt = <731000>;
diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-gsking-x.dts b/arch/arm64/boot/dts/amlogic/meson-g12b-gsking-x.dts
index 6c7bfacbad78..1fa6e75abd21 100644
--- a/arch/arm64/boot/dts/amlogic/meson-g12b-gsking-x.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-g12b-gsking-x.dts
@@ -20,10 +20,16 @@
 		rtc1 = &vrtc;
 	};
 
+	gpio_fan: gpio-fan {
+		compatible = "gpio-fan";
+		gpios = <&gpio GPIOH_5 GPIO_ACTIVE_HIGH>;
+		/* Using Dummy Speed */
+		gpio-fan,speed-map = <0 0>, <1 1>;
+		#cooling-cells = <2>;
+	};
+
 	gpio-keys-polled {
 		compatible = "gpio-keys-polled";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		poll-interval = <100>;
 
 		power-button {
@@ -96,6 +102,23 @@
 	status = "okay";
 };
 
+&cpu_thermal {
+	trips {
+		cpu_active: cpu-active {
+			temperature = <70000>; /* millicelsius */
+			hysteresis = <2000>; /* millicelsius */
+			type = "active";
+		};
+	};
+
+	cooling-maps {
+		map {
+			trip = <&cpu_active>;
+			cooling-device = <&gpio_fan THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+		};
+	};
+};
+
 &frddr_a {
 	status = "okay";
 };
diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-gtking-pro.dts b/arch/arm64/boot/dts/amlogic/meson-g12b-gtking-pro.dts
index 707daf92787b..afe375fa83ca 100644
--- a/arch/arm64/boot/dts/amlogic/meson-g12b-gtking-pro.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-g12b-gtking-pro.dts
@@ -21,8 +21,6 @@
 
 	gpio-keys-polled {
 		compatible = "gpio-keys-polled";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		poll-interval = <100>;
 
 		power-button {
diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dtsi b/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dtsi
index e8a00a2f8812..fd3fa82e4c33 100644
--- a/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-g12b-odroid-n2.dtsi
@@ -17,7 +17,7 @@
 		rtc1 = &vrtc;
 	};
 
-	dioo2133: audio-amplifier-0 {
+	dio2133: audio-amplifier-0 {
 		compatible = "simple-audio-amplifier";
 		enable-gpios = <&gpio_ao GPIOAO_2 GPIO_ACTIVE_HIGH>;
 		VCC-supply = <&vcc_5v>;
@@ -219,7 +219,7 @@
 		audio-widgets = "Line", "Lineout";
 		audio-aux-devs = <&tdmout_b>, <&tdmout_c>, <&tdmin_a>,
 				 <&tdmin_b>, <&tdmin_c>, <&tdmin_lb>,
-				 <&dioo2133>;
+				 <&dio2133>;
 		audio-routing = "TDMOUT_B IN 0", "FRDDR_A OUT 1",
 				"TDMOUT_B IN 1", "FRDDR_B OUT 1",
 				"TDMOUT_B IN 2", "FRDDR_C OUT 1",
@@ -609,7 +609,7 @@
 	pinctrl-0 = <&nor_pins>;
 	pinctrl-names = "default";
 
-	mx25u64: spi-flash@0 {
+	mx25u64: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "mxicy,mx25u6435f", "jedec,spi-nor";
diff --git a/arch/arm64/boot/dts/amlogic/meson-g12b-s922x.dtsi b/arch/arm64/boot/dts/amlogic/meson-g12b-s922x.dtsi
index 1e5d0ee5d541..44c23c984034 100644
--- a/arch/arm64/boot/dts/amlogic/meson-g12b-s922x.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-g12b-s922x.dtsi
@@ -11,26 +11,6 @@
 		compatible = "operating-points-v2";
 		opp-shared;
 
-		opp-100000000 {
-			opp-hz = /bits/ 64 <100000000>;
-			opp-microvolt = <731000>;
-		};
-
-		opp-250000000 {
-			opp-hz = /bits/ 64 <250000000>;
-			opp-microvolt = <731000>;
-		};
-
-		opp-500000000 {
-			opp-hz = /bits/ 64 <500000000>;
-			opp-microvolt = <731000>;
-		};
-
-		opp-667000000 {
-			opp-hz = /bits/ 64 <667000000>;
-			opp-microvolt = <731000>;
-		};
-
 		opp-1000000000 {
 			opp-hz = /bits/ 64 <1000000000>;
 			opp-microvolt = <731000>;
@@ -76,26 +56,6 @@
 		compatible = "operating-points-v2";
 		opp-shared;
 
-		opp-100000000 {
-			opp-hz = /bits/ 64 <100000000>;
-			opp-microvolt = <751000>;
-		};
-
-		opp-250000000 {
-			opp-hz = /bits/ 64 <250000000>;
-			opp-microvolt = <751000>;
-		};
-
-		opp-500000000 {
-			opp-hz = /bits/ 64 <500000000>;
-			opp-microvolt = <751000>;
-		};
-
-		opp-667000000 {
-			opp-hz = /bits/ 64 <667000000>;
-			opp-microvolt = <751000>;
-		};
-
 		opp-1000000000 {
 			opp-hz = /bits/ 64 <1000000000>;
 			opp-microvolt = <771000>;
diff --git a/arch/arm64/boot/dts/amlogic/meson-gx-libretech-pc.dtsi b/arch/arm64/boot/dts/amlogic/meson-gx-libretech-pc.dtsi
index 2d7032f41e4b..bcdf55f48a83 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gx-libretech-pc.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-gx-libretech-pc.dtsi
@@ -416,7 +416,7 @@
 	pinctrl-names = "default";
 	status = "okay";
 
-	gd25lq128: spi-flash@0 {
+	gd25lq128: flash@0 {
 		compatible = "jedec,spi-nor";
 		#address-cells = <1>;
 		#size-cells = <1>;
diff --git a/arch/arm64/boot/dts/amlogic/meson-gx.dtsi b/arch/arm64/boot/dts/amlogic/meson-gx.dtsi
index 6b457b2c30a4..023a52005494 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gx.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-gx.dtsi
@@ -49,6 +49,12 @@
 			no-map;
 		};
 
+		/* 32 MiB reserved for ARM Trusted Firmware (BL32) */
+		secmon_reserved_bl32: secmon@5300000 {
+			reg = <0x0 0x05300000 0x0 0x2000000>;
+			no-map;
+		};
+
 		linux,cma {
 			compatible = "shared-dma-pool";
 			reusable;
@@ -444,7 +450,7 @@
 
 			sysctrl_AO: sys-ctrl@0 {
 				compatible = "amlogic,meson-gx-ao-sysctrl", "simple-mfd", "syscon";
-				reg =  <0x0 0x0 0x0 0x100>;
+				reg = <0x0 0x0 0x0 0x100>;
 
 				clkc_AO: clock-controller {
 					compatible = "amlogic,meson-gx-aoclkc";
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-kii-pro.dts b/arch/arm64/boot/dts/amlogic/meson-gxbb-kii-pro.dts
index e8394a8269ee..6d8cc00fedc7 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxbb-kii-pro.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-kii-pro.dts
@@ -26,8 +26,6 @@
 
 	gpio-keys-polled {
 		compatible = "gpio-keys-polled";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		poll-interval = <20>;
 
 		button-reset {
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts b/arch/arm64/boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts
index f887bfb445fd..63137ce3cb9d 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-nexbox-a95x.dts
@@ -42,11 +42,9 @@
 
 	gpio-keys-polled {
 		compatible = "gpio-keys-polled";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		poll-interval = <100>;
 
-		button@0 {
+		button {
 			label = "reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&gpio_ao GPIOAO_3 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-wetek-play2.dts b/arch/arm64/boot/dts/amlogic/meson-gxbb-wetek-play2.dts
index 6eae692792ec..505ffcd8eb76 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxbb-wetek-play2.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-wetek-play2.dts
@@ -37,11 +37,9 @@
 
 	gpio-keys-polled {
 		compatible = "gpio-keys-polled";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		poll-interval = <100>;
 
-		button@0 {
+		button {
 			label = "reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&gpio_ao GPIOAO_3 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxbb-wetek.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxbb-wetek.dtsi
index a350fee1264d..94dafb955301 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxbb-wetek.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-gxbb-wetek.dtsi
@@ -6,6 +6,8 @@
  */
 
 #include "meson-gxbb.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
 
 / {
 	aliases {
@@ -25,8 +27,10 @@
 	leds {
 		compatible = "gpio-leds";
 
-		led-system {
-			label = "wetek-play:system-status";
+		led-power {
+			/* red in suspend or power-off */
+			color = <LED_COLOR_ID_BLUE>;
+			function = LED_FUNCTION_POWER;
 			gpios = <&gpio_ao GPIOAO_13 GPIO_ACTIVE_HIGH>;
 			default-state = "on";
 			panic-indicator;
@@ -64,6 +68,7 @@
 		regulator-name = "VDDIO_AO18";
 		regulator-min-microvolt = <1800000>;
 		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
 	};
 
 	vcc_3v3: regulator-vcc_3v3 {
@@ -161,6 +166,7 @@
 	status = "okay";
 	pinctrl-0 = <&hdmi_hpd_pins>, <&hdmi_i2c_pins>;
 	pinctrl-names = "default";
+	hdmi-supply = <&vddio_ao18>;
 };
 
 &hdmi_tx_tmds_port {
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s805x-libretech-ac.dts b/arch/arm64/boot/dts/amlogic/meson-gxl-s805x-libretech-ac.dts
index 2d769203f671..213a0705ebdc 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxl-s805x-libretech-ac.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s805x-libretech-ac.dts
@@ -298,7 +298,7 @@
 	pinctrl-0 = <&nor_pins>;
 	pinctrl-names = "default";
 
-	w25q32: spi-flash@0 {
+	w25q32: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "jedec,spi-nor";
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s805x-p241.dts b/arch/arm64/boot/dts/amlogic/meson-gxl-s805x-p241.dts
index eb7f5a3fefd4..ff906becd2ab 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxl-s805x-p241.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s805x-p241.dts
@@ -8,6 +8,7 @@
 /dts-v1/;
 
 #include <dt-bindings/input/input.h>
+#include <dt-bindings/sound/meson-aiu.h>
 
 #include "meson-gxl-s805x.dtsi"
 
@@ -21,6 +22,13 @@
 		ethernet0 = &ethmac;
 	};
 
+	au2: analog-amplifier {
+		compatible = "simple-audio-amplifier";
+		sound-name-prefix = "AU2";
+		VCC-supply = <&vcc_5v>;
+		enable-gpios = <&gpio GPIOH_5 GPIO_ACTIVE_HIGH>;
+	};
+
 	chosen {
 		stdout-path = "serial0:115200n8";
 	};
@@ -84,6 +92,14 @@
 		regulator-max-microvolt = <3300000>;
 	};
 
+	vcc_5v: regulator-vcc-5v {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+
 	emmc_pwrseq: emmc-pwrseq {
 		compatible = "mmc-pwrseq-emmc";
 		reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
@@ -102,6 +118,68 @@
 		clocks = <&wifi32k>;
 		clock-names = "ext_clock";
 	};
+
+	sound {
+		compatible = "amlogic,gx-sound-card";
+		model = "GXL-P241";
+		audio-aux-devs = <&au2>;
+		audio-widgets = "Line", "Lineout";
+		audio-routing = "AU2 INL", "ACODEC LOLN",
+				"AU2 INR", "ACODEC LORN",
+				"Lineout", "AU2 OUTL",
+				"Lineout", "AU2 OUTR";
+		assigned-clocks = <&clkc CLKID_MPLL0>,
+				  <&clkc CLKID_MPLL1>,
+				  <&clkc CLKID_MPLL2>;
+		assigned-clock-parents = <0>, <0>, <0>;
+		assigned-clock-rates = <294912000>,
+				       <270950400>,
+				       <393216000>;
+		status = "okay";
+
+		dai-link-0 {
+			sound-dai = <&aiu AIU_CPU CPU_I2S_FIFO>;
+		};
+
+		dai-link-1 {
+			sound-dai = <&aiu AIU_CPU CPU_I2S_ENCODER>;
+			dai-format = "i2s";
+			mclk-fs = <256>;
+
+			codec-0 {
+				sound-dai = <&aiu AIU_HDMI CTRL_I2S>;
+			};
+
+			codec-1 {
+				sound-dai = <&aiu AIU_ACODEC CTRL_I2S>;
+			};
+		};
+
+		dai-link-2 {
+			sound-dai = <&aiu AIU_HDMI CTRL_OUT>;
+
+			codec-0 {
+				sound-dai = <&hdmi_tx>;
+			};
+		};
+
+		dai-link-3 {
+			sound-dai = <&aiu AIU_ACODEC CTRL_OUT>;
+
+			codec-0 {
+				sound-dai = <&acodec>;
+			};
+		};
+	};
+};
+
+&acodec {
+	AVDD-supply = <&vddio_ao18>;
+	status = "okay";
+};
+
+&aiu {
+	status = "okay";
 };
 
 &cec_AO {
@@ -136,6 +214,7 @@
 	status = "okay";
 	pinctrl-0 = <&hdmi_hpd_pins>, <&hdmi_i2c_pins>;
 	pinctrl-names = "default";
+	hdmi-supply = <&vcc_5v>;
 };
 
 &hdmi_tx_tmds_port {
@@ -220,3 +299,7 @@
 	status = "okay";
 	dr_mode = "host";
 };
+
+&usb2_phy0 {
+	phy-supply = <&vcc_5v>;
+};
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-mecool-kii-pro.dts b/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-mecool-kii-pro.dts
index c529b6c860a4..a4fa186f0458 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-mecool-kii-pro.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-mecool-kii-pro.dts
@@ -30,11 +30,9 @@
 
 	gpio-keys-polled {
 		compatible = "gpio-keys-polled";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		poll-interval = <100>;
 
-		button@0 {
+		button {
 			label = "power";
 			linux,code = <KEY_POWER>;
 			gpios = <&gpio_ao GPIOAO_2 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-p230.dts b/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-p230.dts
index b2ab05c22090..c1470416faad 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-p230.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-p230.dts
@@ -30,11 +30,9 @@
 
 	gpio-keys-polled {
 		compatible = "gpio-keys-polled";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		poll-interval = <100>;
 
-		button@0 {
+		button {
 			label = "power";
 			linux,code = <KEY_POWER>;
 			gpios = <&gpio_ao GPIOAO_2 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-vero4k-plus.dts b/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-vero4k-plus.dts
new file mode 100644
index 000000000000..595b49085074
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s905d-vero4k-plus.dts
@@ -0,0 +1,115 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Author: Christian Hewitt <christianshewitt@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "meson-gxl-s905d.dtsi"
+#include "meson-gx-p23x-q20x.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+	compatible = "osmc,vero4k-plus", "amlogic,s905d", "amlogic,meson-gxl";
+	model = "OSMC Vero 4K Plus";
+
+	gpio-keys-polled {
+		compatible = "gpio-keys-polled";
+		poll-interval = <20>;
+
+		button {
+			label = "power";
+			linux,code = <KEY_POWER>;
+			gpios = <&gpio_ao GPIOAO_2 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-standby {
+			color = <LED_COLOR_ID_RED>;
+			function = LED_FUNCTION_POWER;
+			gpios = <&gpio_ao GPIOAO_9 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+			panic-indicator;
+		};
+	};
+};
+
+&ethmac {
+	pinctrl-0 = <&eth_pins>;
+	pinctrl-names = "default";
+
+	phy-mode = "rgmii-txid";
+	phy-handle = <&external_phy>;
+
+	amlogic,tx-delay-ns = <0>;
+};
+
+&external_mdio {
+	external_phy: ethernet-phy@0 {
+		/* Realtek RTL8211F (0x001cc916) */
+		pinctrl-0 = <&eth_phy_irq_pin>;
+		pinctrl-names = "default";
+
+		reg = <0>;
+		max-speed = <1000>;
+
+		reset-assert-us = <10000>;
+		reset-deassert-us = <80000>;
+		reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>;
+
+		interrupt-parent = <&gpio_intc>;
+		interrupts = <25 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
+&pinctrl_periphs {
+	/* Ensure the phy irq pin is properly configured as input */
+	eth_phy_irq_pin: eth-phy-irq {
+		mux {
+			groups = "GPIOZ_15";
+			function = "gpio_periphs";
+			bias-disable;
+			output-disable;
+		};
+	};
+};
+
+&sd_emmc_a {
+	brcmf: wifi@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+	};
+};
+
+&uart_A {
+	status = "okay";
+	pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>;
+	pinctrl-names = "default";
+	uart-has-rtscts;
+
+	bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		shutdown-gpios = <&gpio GPIOX_17 GPIO_ACTIVE_HIGH>;
+		max-speed = <2000000>;
+		clocks = <&wifi32k>;
+		clock-names = "lpo";
+	};
+};
+
+&usb {
+	dr_mode = "host";
+};
+
+&usb2_phy0 {
+	/* HDMI_5V also supplies the USB VBUS */
+	phy-supply = <&hdmi_5v>;
+};
+
+&usb2_phy0 {
+	/* HDMI_5V also supplies the USB VBUS */
+	phy-supply = <&hdmi_5v>;
+};
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s905w-jethome-jethub-j80.dts b/arch/arm64/boot/dts/amlogic/meson-gxl-s905w-jethome-jethub-j80.dts
index 6eafb908695f..6831137c5c10 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxl-s905w-jethome-jethub-j80.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s905w-jethome-jethub-j80.dts
@@ -213,6 +213,12 @@
 	pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>;
 	pinctrl-names = "default";
 	uart-has-rtscts;
+
+	bluetooth {
+		compatible = "realtek,rtl8822cs-bt";
+		enable-gpios = <&gpio GPIOX_17 GPIO_ACTIVE_HIGH>;
+		host-wake-gpios = <&gpio GPIOX_18 GPIO_ACTIVE_HIGH>;
+       };
 };
 
 &uart_C {
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-libretech-cc-v2.dts b/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-libretech-cc-v2.dts
index 93d8f8aff70d..874f91c348ec 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-libretech-cc-v2.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-libretech-cc-v2.dts
@@ -284,7 +284,7 @@
 	pinctrl-0 = <&nor_pins>;
 	pinctrl-names = "default";
 
-	nor_4u1: spi-flash@0 {
+	nor_4u1: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "jedec,spi-nor";
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxm-gt1-ultimate.dts b/arch/arm64/boot/dts/amlogic/meson-gxm-gt1-ultimate.dts
new file mode 100644
index 000000000000..2c267884cc16
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-gxm-gt1-ultimate.dts
@@ -0,0 +1,91 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) Christian Hewitt <christianshewitt@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "meson-gxm.dtsi"
+#include "meson-gx-p23x-q20x.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+	compatible = "azw,gt1-ultimate", "amlogic,s912", "amlogic,meson-gxm";
+	model = "Beelink GT1 Ultimate";
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-white {
+			color = <LED_COLOR_ID_WHITE>;
+			function = LED_FUNCTION_POWER;
+			gpios = <&gpio_ao GPIOAO_9 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+			panic-indicator;
+		};
+	};
+
+	adc-keys {
+		compatible = "adc-keys";
+		io-channels = <&saradc 0>;
+		io-channel-names = "buttons";
+		keyup-threshold-microvolt = <1710000>;
+
+		button-function {
+			label = "update";
+			linux,code = <KEY_VENDOR>;
+			press-threshold-microvolt = <10000>;
+		};
+	};
+};
+
+&ethmac {
+	pinctrl-0 = <&eth_pins>;
+	pinctrl-names = "default";
+	phy-handle = <&external_phy>;
+	amlogic,tx-delay-ns = <2>;
+	phy-mode = "rgmii";
+};
+
+&external_mdio {
+	external_phy: ethernet-phy@0 {
+		/* Realtek RTL8211F (0x001cc916) */
+		reg = <0>;
+		max-speed = <1000>;
+
+		reset-assert-us = <10000>;
+		reset-deassert-us = <80000>;
+		reset-gpios = <&gpio GPIOZ_14 GPIO_ACTIVE_LOW>;
+
+		interrupt-parent = <&gpio_intc>;
+		/* MAC_INTR on GPIOZ_15 */
+		interrupts = <25 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
+&ir {
+	linux,rc-map-name = "rc-beelink-gs1";
+};
+
+&sd_emmc_a {
+	brcmf: wifi@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+	};
+};
+
+&uart_A {
+	status = "okay";
+	pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>;
+	pinctrl-names = "default";
+	uart-has-rtscts;
+
+	bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		shutdown-gpios = <&gpio GPIOX_17 GPIO_ACTIVE_HIGH>;
+		max-speed = <2000000>;
+		clocks = <&wifi32k>;
+		clock-names = "lpo";
+	};
+};
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxm-khadas-vim2.dts b/arch/arm64/boot/dts/amlogic/meson-gxm-khadas-vim2.dts
index 86bdc0baf032..f43c45daf7eb 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxm-khadas-vim2.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxm-khadas-vim2.dts
@@ -374,7 +374,7 @@
 	pinctrl-0 = <&nor_pins>;
 	pinctrl-names = "default";
 
-	w25q32: spi-flash@0 {
+	w25q32: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "winbond,w25q16", "jedec,spi-nor";
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxm-mecool-kiii-pro.dts b/arch/arm64/boot/dts/amlogic/meson-gxm-mecool-kiii-pro.dts
index ebebf344b715..f5b3424c0f61 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxm-mecool-kiii-pro.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxm-mecool-kiii-pro.dts
@@ -35,11 +35,9 @@
 
 	gpio-keys-polled {
 		compatible = "gpio-keys-polled";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		poll-interval = <100>;
 
-		button@0 {
+		button {
 			label = "power";
 			linux,code = <KEY_POWER>;
 			gpios = <&gpio_ao GPIOAO_2 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxm-minix-neo-u9h.dts b/arch/arm64/boot/dts/amlogic/meson-gxm-minix-neo-u9h.dts
index ea9f234d1fc7..b8ef3bd8b840 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxm-minix-neo-u9h.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxm-minix-neo-u9h.dts
@@ -41,11 +41,9 @@
 
 	gpio-keys-polled {
 		compatible = "gpio-keys-polled";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		poll-interval = <100>;
 
-		button@0 {
+		button {
 			label = "power";
 			linux,code = <KEY_POWER>;
 			gpios = <&gpio_ao GPIOAO_2 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxm-q200.dts b/arch/arm64/boot/dts/amlogic/meson-gxm-q200.dts
index 8edbfe040805..d4858afa0e9c 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxm-q200.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxm-q200.dts
@@ -30,11 +30,9 @@
 
 	gpio-keys-polled {
 		compatible = "gpio-keys-polled";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		poll-interval = <100>;
 
-		button@0 {
+		button {
 			label = "power";
 			linux,code = <KEY_POWER>;
 			gpios = <&gpio_ao GPIOAO_2 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm64/boot/dts/amlogic/meson-gxm-wetek-core2.dts b/arch/arm64/boot/dts/amlogic/meson-gxm-wetek-core2.dts
index 1e7f77f9b533..f8c40340b9c5 100644
--- a/arch/arm64/boot/dts/amlogic/meson-gxm-wetek-core2.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-gxm-wetek-core2.dts
@@ -45,8 +45,6 @@
 
 	gpio-keys-polled {
 		compatible = "gpio-keys-polled";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		poll-interval = <100>;
 
 		button-power {
diff --git a/arch/arm64/boot/dts/amlogic/meson-khadas-vim3.dtsi b/arch/arm64/boot/dts/amlogic/meson-khadas-vim3.dtsi
index 3cf4ecb6d52e..c9705941e4ab 100644
--- a/arch/arm64/boot/dts/amlogic/meson-khadas-vim3.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-khadas-vim3.dtsi
@@ -458,7 +458,7 @@
 	pinctrl-0 = <&nor_pins>;
 	pinctrl-names = "default";
 
-	w25q128: spi-flash@0 {
+	w25q128: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "winbond,w25q128fw", "jedec,spi-nor";
diff --git a/arch/arm64/boot/dts/amlogic/meson-s4-s805x2-aq222.dts b/arch/arm64/boot/dts/amlogic/meson-s4-s805x2-aq222.dts
new file mode 100644
index 000000000000..8ffbcb2b1ac5
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-s4-s805x2-aq222.dts
@@ -0,0 +1,30 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2021 Amlogic, Inc. All rights reserved.
+ */
+
+/dts-v1/;
+
+#include "meson-s4.dtsi"
+
+/ {
+	model = "Amlogic Meson S4 AQ222 Development Board";
+	compatible = "amlogic,aq222", "amlogic,s4";
+	interrupt-parent = <&gic>;
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	aliases {
+		serial0 = &uart_B;
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x40000000>;
+	};
+
+};
+
+&uart_B {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/amlogic/meson-s4.dtsi b/arch/arm64/boot/dts/amlogic/meson-s4.dtsi
new file mode 100644
index 000000000000..ad50cba42d19
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-s4.dtsi
@@ -0,0 +1,138 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2021 Amlogic, Inc. All rights reserved.
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	cpus {
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a35";
+			reg = <0x0 0x0>;
+			enable-method = "psci";
+		};
+
+		cpu1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a35";
+			reg = <0x0 0x1>;
+			enable-method = "psci";
+		};
+
+		cpu2: cpu@2 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a35";
+			reg = <0x0 0x2>;
+			enable-method = "psci";
+		};
+
+		cpu3: cpu@3 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a35";
+			reg = <0x0 0x3>;
+			enable-method = "psci";
+		};
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+	};
+
+	psci {
+		compatible = "arm,psci-1.0";
+		method = "smc";
+	};
+
+	xtal: xtal-clk {
+		compatible = "fixed-clock";
+		clock-frequency = <24000000>;
+		clock-output-names = "xtal";
+		#clock-cells = <0>;
+	};
+
+	pwrc: power-controller {
+		compatible = "amlogic,meson-s4-pwrc";
+		#power-domain-cells = <1>;
+		status = "okay";
+	};
+
+	soc {
+		compatible = "simple-bus";
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		gic: interrupt-controller@fff01000 {
+			compatible = "arm,gic-400";
+			#interrupt-cells = <3>;
+			#address-cells = <0>;
+			interrupt-controller;
+			reg = <0x0 0xfff01000 0 0x1000>,
+			      <0x0 0xfff02000 0 0x2000>,
+			      <0x0 0xfff04000 0 0x2000>,
+			      <0x0 0xfff06000 0 0x2000>;
+			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+		};
+
+		apb4: apb4@fe000000 {
+			compatible = "simple-bus";
+			reg = <0x0 0xfe000000 0x0 0x480000>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges = <0x0 0x0 0x0 0xfe000000 0x0 0x480000>;
+
+			periphs_pinctrl: pinctrl@4000 {
+				compatible = "amlogic,meson-s4-periphs-pinctrl";
+				#address-cells = <2>;
+				#size-cells = <2>;
+				ranges;
+
+				gpio: bank@4000 {
+					reg = <0x0 0x4000 0x0 0x004c>,
+					      <0x0 0x40c0 0x0 0x0220>;
+					reg-names = "mux", "gpio";
+					gpio-controller;
+					#gpio-cells = <2>;
+					gpio-ranges = <&periphs_pinctrl 0 0 82>;
+				};
+			};
+
+			gpio_intc: interrupt-controller@4080 {
+				compatible = "amlogic,meson-s4-gpio-intc",
+					     "amlogic,meson-gpio-intc";
+				reg = <0x0 0x4080 0x0 0x20>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				amlogic,channel-interrupts =
+					<10 11 12 13 14 15 16 17 18 19 20 21>;
+			};
+
+			uart_B: serial@7a000 {
+				compatible = "amlogic,meson-s4-uart",
+					     "amlogic,meson-ao-uart";
+				reg = <0x0 0x7a000 0x0 0x18>;
+				interrupts = <GIC_SPI 169 IRQ_TYPE_EDGE_RISING>;
+				status = "disabled";
+				clocks = <&xtal>, <&xtal>, <&xtal>;
+				clock-names = "xtal", "pclk", "baud";
+			};
+
+			reset: reset-controller@2000 {
+				compatible = "amlogic,meson-s4-reset";
+				reg = <0x0 0x2000 0x0 0x98>;
+				#reset-cells = <1>;
+			};
+		};
+	};
+};
diff --git a/arch/arm64/boot/dts/amlogic/meson-sm1-a95xf3-air-gbit.dts b/arch/arm64/boot/dts/amlogic/meson-sm1-a95xf3-air-gbit.dts
new file mode 100644
index 000000000000..d1debccdc1c2
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-sm1-a95xf3-air-gbit.dts
@@ -0,0 +1,129 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2019 BayLibre SAS. All rights reserved.
+ * Copyright (c) 2020 Christian Hewitt <christianshewitt@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "meson-sm1-ac2xx.dtsi"
+#include <dt-bindings/sound/meson-g12a-tohdmitx.h>
+
+/ {
+	compatible = "cyx,a95xf3-air-gbit", "amlogic,sm1";
+	model = "Shenzhen CYX Industrial Co., Ltd A95XF3-AIR";
+
+	sound {
+		compatible = "amlogic,axg-sound-card";
+		model = "A95XF3-AIR";
+		audio-aux-devs = <&tdmout_b>;
+		audio-routing = "TDMOUT_B IN 0", "FRDDR_A OUT 1",
+				"TDMOUT_B IN 1", "FRDDR_B OUT 1",
+				"TDMOUT_B IN 2", "FRDDR_C OUT 1",
+				"TDM_B Playback", "TDMOUT_B OUT";
+
+		assigned-clocks = <&clkc CLKID_MPLL2>,
+				  <&clkc CLKID_MPLL0>,
+				  <&clkc CLKID_MPLL1>;
+		assigned-clock-parents = <0>, <0>, <0>;
+		assigned-clock-rates = <294912000>,
+				       <270950400>,
+				       <393216000>;
+		status = "okay";
+
+		dai-link-0 {
+			sound-dai = <&frddr_a>;
+		};
+
+		dai-link-1 {
+			sound-dai = <&frddr_b>;
+		};
+
+		dai-link-2 {
+			sound-dai = <&frddr_c>;
+		};
+
+		/* 8ch hdmi interface */
+		dai-link-3 {
+			sound-dai = <&tdmif_b>;
+			dai-format = "i2s";
+			dai-tdm-slot-tx-mask-0 = <1 1>;
+			dai-tdm-slot-tx-mask-1 = <1 1>;
+			dai-tdm-slot-tx-mask-2 = <1 1>;
+			dai-tdm-slot-tx-mask-3 = <1 1>;
+			mclk-fs = <256>;
+
+			codec {
+				sound-dai = <&tohdmitx TOHDMITX_I2S_IN_B>;
+			};
+		};
+
+		/* hdmi glue */
+		dai-link-4 {
+			sound-dai = <&tohdmitx TOHDMITX_I2S_OUT>;
+
+			codec {
+				sound-dai = <&hdmi_tx>;
+			};
+		};
+	};
+};
+
+&arb {
+	status = "okay";
+};
+
+&clkc_audio {
+	status = "okay";
+};
+
+&ethmac {
+	status = "okay";
+
+	pinctrl-0 = <&eth_pins>, <&eth_rgmii_pins>;
+	pinctrl-names = "default";
+	phy-mode = "rgmii-txid";
+	phy-handle = <&external_phy>;
+
+	rx-internal-delay-ps = <800>;
+};
+
+&ext_mdio {
+	external_phy: ethernet-phy@0 {
+		/* Realtek RTL8211F (0x001cc916) */
+		reg = <0>;
+		max-speed = <1000>;
+
+		reset-assert-us = <10000>;
+		reset-deassert-us = <80000>;
+		reset-gpios = <&gpio GPIOZ_15 (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
+
+		interrupt-parent = <&gpio_intc>;
+		/* MAC_INTR on GPIOZ_14 */
+		interrupts = <26 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
+&frddr_a {
+	status = "okay";
+};
+
+&frddr_b {
+	status = "okay";
+};
+
+&frddr_c {
+	status = "okay";
+};
+
+&tdmif_b {
+	status = "okay";
+};
+
+&tdmout_b {
+	status = "okay";
+};
+
+&tohdmitx {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/amlogic/meson-sm1-a95xf3-air.dts b/arch/arm64/boot/dts/amlogic/meson-sm1-a95xf3-air.dts
new file mode 100644
index 000000000000..c94f2870b78b
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-sm1-a95xf3-air.dts
@@ -0,0 +1,108 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2019 BayLibre SAS. All rights reserved.
+ * Copyright (c) 2020 Christian Hewitt <christianshewitt@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "meson-sm1-ac2xx.dtsi"
+#include <dt-bindings/sound/meson-g12a-tohdmitx.h>
+
+/ {
+	compatible = "cyx,a95xf3-air", "amlogic,sm1";
+	model = "Shenzhen CYX Industrial Co., Ltd A95XF3-AIR";
+
+	sound {
+		compatible = "amlogic,axg-sound-card";
+		model = "A95XF3-AIR";
+		audio-aux-devs = <&tdmout_b>;
+		audio-routing = "TDMOUT_B IN 0", "FRDDR_A OUT 1",
+				"TDMOUT_B IN 1", "FRDDR_B OUT 1",
+				"TDMOUT_B IN 2", "FRDDR_C OUT 1",
+				"TDM_B Playback", "TDMOUT_B OUT";
+
+		assigned-clocks = <&clkc CLKID_MPLL2>,
+				  <&clkc CLKID_MPLL0>,
+				  <&clkc CLKID_MPLL1>;
+		assigned-clock-parents = <0>, <0>, <0>;
+		assigned-clock-rates = <294912000>,
+				       <270950400>,
+				       <393216000>;
+		status = "okay";
+
+		dai-link-0 {
+			sound-dai = <&frddr_a>;
+		};
+
+		dai-link-1 {
+			sound-dai = <&frddr_b>;
+		};
+
+		dai-link-2 {
+			sound-dai = <&frddr_c>;
+		};
+
+		/* 8ch hdmi interface */
+		dai-link-3 {
+			sound-dai = <&tdmif_b>;
+			dai-format = "i2s";
+			dai-tdm-slot-tx-mask-0 = <1 1>;
+			dai-tdm-slot-tx-mask-1 = <1 1>;
+			dai-tdm-slot-tx-mask-2 = <1 1>;
+			dai-tdm-slot-tx-mask-3 = <1 1>;
+			mclk-fs = <256>;
+
+			codec {
+				sound-dai = <&tohdmitx TOHDMITX_I2S_IN_B>;
+			};
+		};
+
+		/* hdmi glue */
+		dai-link-4 {
+			sound-dai = <&tohdmitx TOHDMITX_I2S_OUT>;
+
+			codec {
+				sound-dai = <&hdmi_tx>;
+			};
+		};
+	};
+};
+
+&arb {
+	status = "okay";
+};
+
+&clkc_audio {
+	status = "okay";
+};
+
+&ethmac {
+	status = "okay";
+	phy-handle = <&internal_ephy>;
+	phy-mode = "rmii";
+};
+
+&frddr_a {
+	status = "okay";
+};
+
+&frddr_b {
+	status = "okay";
+};
+
+&frddr_c {
+	status = "okay";
+};
+
+&tdmif_b {
+	status = "okay";
+};
+
+&tdmout_b {
+	status = "okay";
+};
+
+&tohdmitx {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/amlogic/meson-sm1-ac2xx.dtsi b/arch/arm64/boot/dts/amlogic/meson-sm1-ac2xx.dtsi
new file mode 100644
index 000000000000..46a34731f7e2
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-sm1-ac2xx.dtsi
@@ -0,0 +1,300 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2019 BayLibre SAS. All rights reserved.
+ * Copyright (c) 2020 Christian Hewitt <christianshewitt@gmail.com>
+ *
+ * AC200/AC202 = S905D3
+ * AC213/AC214 = S905X3
+ *
+ */
+
+#include "meson-sm1.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/gpio/meson-g12a-gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+	aliases {
+		serial0 = &uart_AO;
+		ethernet0 = &ethmac;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	emmc_pwrseq: emmc-pwrseq {
+		compatible = "mmc-pwrseq-emmc";
+		reset-gpios = <&gpio BOOT_12 GPIO_ACTIVE_LOW>;
+	};
+
+	cvbs-connector {
+		compatible = "composite-video-connector";
+
+		port {
+			cvbs_connector_in: endpoint {
+				remote-endpoint = <&cvbs_vdac_out>;
+			};
+		};
+	};
+
+	hdmi-connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_connector_in: endpoint {
+				remote-endpoint = <&hdmi_tx_tmds_out>;
+			};
+		};
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x40000000>;
+	};
+
+	ao_5v: regulator-ao_5v {
+		compatible = "regulator-fixed";
+		regulator-name = "AO_5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&dc_in>;
+		regulator-always-on;
+	};
+
+	dc_in: regulator-dc_in {
+		compatible = "regulator-fixed";
+		regulator-name = "DC_IN";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+	};
+
+	emmc_1v8: regulator-emmc_1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "EMMC_1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vddao_3v3>;
+		regulator-always-on;
+	};
+
+	vddao_3v3: regulator-vddao_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDAO_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&dc_in>;
+		regulator-always-on;
+	};
+
+	vddcpu: regulator-vddcpu {
+		compatible = "pwm-regulator";
+
+		regulator-name = "VDDCPU";
+		regulator-min-microvolt = <690000>;
+		regulator-max-microvolt = <1050000>;
+
+		vin-supply = <&dc_in>;
+
+		pwms = <&pwm_AO_cd 1 1500 0>;
+		pwm-dutycycle-range = <100 0>;
+
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	vddio_ao1v8: regulator-vddio_ao1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDIO_AO1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vddao_3v3>;
+		regulator-always-on;
+	};
+
+	sdio_pwrseq: sdio-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
+		clocks = <&wifi32k>;
+		clock-names = "ext_clock";
+	};
+
+	wifi32k: wifi32k {
+		compatible = "pwm-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */
+	};
+};
+
+&cec_AO {
+	pinctrl-0 = <&cec_ao_a_h_pins>;
+	pinctrl-names = "default";
+	status = "disabled";
+	hdmi-phandle = <&hdmi_tx>;
+};
+
+&cecb_AO {
+	pinctrl-0 = <&cec_ao_b_h_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+	hdmi-phandle = <&hdmi_tx>;
+};
+
+&cpu0 {
+	cpu-supply = <&vddcpu>;
+	operating-points-v2 = <&cpu_opp_table>;
+	clocks = <&clkc CLKID_CPU_CLK>;
+	clock-latency = <50000>;
+};
+
+&cpu1 {
+	cpu-supply = <&vddcpu>;
+	operating-points-v2 = <&cpu_opp_table>;
+	clocks = <&clkc CLKID_CPU1_CLK>;
+	clock-latency = <50000>;
+};
+
+&cpu2 {
+	cpu-supply = <&vddcpu>;
+	operating-points-v2 = <&cpu_opp_table>;
+	clocks = <&clkc CLKID_CPU2_CLK>;
+	clock-latency = <50000>;
+};
+
+&cpu3 {
+	cpu-supply = <&vddcpu>;
+	operating-points-v2 = <&cpu_opp_table>;
+	clocks = <&clkc CLKID_CPU3_CLK>;
+	clock-latency = <50000>;
+};
+
+&cvbs_vdac_port {
+	cvbs_vdac_out: endpoint {
+		remote-endpoint = <&cvbs_connector_in>;
+	};
+};
+
+&hdmi_tx {
+	status = "okay";
+	pinctrl-0 = <&hdmitx_hpd_pins>, <&hdmitx_ddc_pins>;
+	pinctrl-names = "default";
+};
+
+&hdmi_tx_tmds_port {
+	hdmi_tx_tmds_out: endpoint {
+		remote-endpoint = <&hdmi_connector_in>;
+	};
+};
+
+&ir {
+	status = "okay";
+	pinctrl-0 = <&remote_input_ao_pins>;
+	pinctrl-names = "default";
+};
+
+&pwm_AO_ab {
+	status = "okay";
+	pinctrl-0 = <&pwm_ao_a_pins>;
+	pinctrl-names = "default";
+	clocks = <&xtal>;
+	clock-names = "clkin0";
+};
+
+&pwm_AO_cd {
+	pinctrl-0 = <&pwm_ao_d_e_pins>;
+	pinctrl-names = "default";
+	clocks = <&xtal>;
+	clock-names = "clkin1";
+	status = "okay";
+};
+
+&pwm_ef {
+	status = "okay";
+	pinctrl-0 = <&pwm_e_pins>;
+	pinctrl-names = "default";
+	clocks = <&xtal>;
+	clock-names = "clkin0";
+};
+
+&saradc {
+	status = "okay";
+	vref-supply = <&vddio_ao1v8>;
+};
+
+/* SDIO */
+&sd_emmc_a {
+	status = "okay";
+	pinctrl-0 = <&sdio_pins>;
+	pinctrl-1 = <&sdio_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	bus-width = <4>;
+	cap-sd-highspeed;
+	sd-uhs-sdr104;
+	max-frequency = <200000000>;
+
+	non-removable;
+	disable-wp;
+
+	/* WiFi firmware requires power to be kept while in suspend */
+	keep-power-in-suspend;
+
+	mmc-pwrseq = <&sdio_pwrseq>;
+
+	vmmc-supply = <&vddao_3v3>;
+	vqmmc-supply = <&vddio_ao1v8>;
+};
+
+/* SD Card */
+&sd_emmc_b {
+	status = "okay";
+	pinctrl-0 = <&sdcard_c_pins>;
+	pinctrl-1 = <&sdcard_clk_gate_c_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <4>;
+	cap-sd-highspeed;
+	/* CRC errors are observed at 50MHz */
+	max-frequency = <35000000>;
+	disable-wp;
+
+	cd-gpios = <&gpio GPIOC_6 GPIO_ACTIVE_LOW>;
+	vmmc-supply = <&vddao_3v3>;
+	vqmmc-supply = <&vddao_3v3>;
+};
+
+/* eMMC */
+&sd_emmc_c {
+	status = "okay";
+	pinctrl-0 = <&emmc_ctrl_pins>, <&emmc_data_8b_pins>, <&emmc_ds_pins>;
+	pinctrl-1 = <&emmc_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <8>;
+	cap-mmc-highspeed;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+	max-frequency = <200000000>;
+	non-removable;
+	disable-wp;
+
+	mmc-pwrseq = <&emmc_pwrseq>;
+	vmmc-supply = <&vddao_3v3>;
+	vqmmc-supply = <&emmc_1v8>;
+};
+
+&uart_AO {
+	status = "okay";
+	pinctrl-0 = <&uart_ao_a_pins>;
+	pinctrl-names = "default";
+};
+
+&usb {
+	status = "okay";
+	dr_mode = "otg";
+};
diff --git a/arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m5.dts b/arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m5.dts
index 212c6aa5a3b8..cadba194b149 100644
--- a/arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m5.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-sm1-bananapi-m5.dts
@@ -123,7 +123,7 @@
 		regulator-min-microvolt = <1800000>;
 		regulator-max-microvolt = <3300000>;
 
-		enable-gpio = <&gpio GPIOE_2 GPIO_ACTIVE_HIGH>;
+		enable-gpio = <&gpio_ao GPIOE_2 GPIO_ACTIVE_HIGH>;
 		enable-active-high;
 		regulator-always-on;
 
@@ -437,6 +437,7 @@
 		"",
 		"eMMC_RST#", /* BOOT_12 */
 		"eMMC_DS", /* BOOT_13 */
+		"", "",
 		/* GPIOC */
 		"SD_D0_B", /* GPIOC_0 */
 		"SD_D1_B", /* GPIOC_1 */
diff --git a/arch/arm64/boot/dts/amlogic/meson-sm1-h96-max.dts b/arch/arm64/boot/dts/amlogic/meson-sm1-h96-max.dts
new file mode 100644
index 000000000000..0f6660e68e72
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-sm1-h96-max.dts
@@ -0,0 +1,145 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2019 BayLibre SAS. All rights reserved.
+ * Copyright (c) 2020 Christian Hewitt <christianshewitt@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "meson-sm1-ac2xx.dtsi"
+#include <dt-bindings/sound/meson-g12a-tohdmitx.h>
+
+/ {
+	compatible = "haochuangyi,h96-max", "amlogic,sm1";
+	model = "Shenzhen Haochuangyi Technology Co., Ltd H96 Max";
+
+	sound {
+		compatible = "amlogic,axg-sound-card";
+		model = "H96-MAX";
+		audio-aux-devs = <&tdmout_b>;
+		audio-routing = "TDMOUT_B IN 0", "FRDDR_A OUT 1",
+				"TDMOUT_B IN 1", "FRDDR_B OUT 1",
+				"TDMOUT_B IN 2", "FRDDR_C OUT 1",
+				"TDM_B Playback", "TDMOUT_B OUT";
+
+		assigned-clocks = <&clkc CLKID_MPLL2>,
+				  <&clkc CLKID_MPLL0>,
+				  <&clkc CLKID_MPLL1>;
+		assigned-clock-parents = <0>, <0>, <0>;
+		assigned-clock-rates = <294912000>,
+				       <270950400>,
+				       <393216000>;
+		status = "okay";
+
+		dai-link-0 {
+			sound-dai = <&frddr_a>;
+		};
+
+		dai-link-1 {
+			sound-dai = <&frddr_b>;
+		};
+
+		dai-link-2 {
+			sound-dai = <&frddr_c>;
+		};
+
+		/* 8ch hdmi interface */
+		dai-link-3 {
+			sound-dai = <&tdmif_b>;
+			dai-format = "i2s";
+			dai-tdm-slot-tx-mask-0 = <1 1>;
+			dai-tdm-slot-tx-mask-1 = <1 1>;
+			dai-tdm-slot-tx-mask-2 = <1 1>;
+			dai-tdm-slot-tx-mask-3 = <1 1>;
+			mclk-fs = <256>;
+
+			codec {
+				sound-dai = <&tohdmitx TOHDMITX_I2S_IN_B>;
+			};
+		};
+
+		/* hdmi glue */
+		dai-link-4 {
+			sound-dai = <&tohdmitx TOHDMITX_I2S_OUT>;
+
+			codec {
+				sound-dai = <&hdmi_tx>;
+			};
+		};
+	};
+};
+
+&arb {
+	status = "okay";
+};
+
+&clkc_audio {
+	status = "okay";
+};
+
+&ethmac {
+	status = "okay";
+
+	pinctrl-0 = <&eth_pins>, <&eth_rgmii_pins>;
+	pinctrl-names = "default";
+	phy-mode = "rgmii-txid";
+	phy-handle = <&external_phy>;
+
+	rx-internal-delay-ps = <800>;
+};
+
+&ext_mdio {
+	external_phy: ethernet-phy@0 {
+		/* Realtek RTL8211F (0x001cc916) */
+		reg = <0>;
+		max-speed = <1000>;
+
+		reset-assert-us = <10000>;
+		reset-deassert-us = <80000>;
+		reset-gpios = <&gpio GPIOZ_15 (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
+
+		interrupt-parent = <&gpio_intc>;
+		/* MAC_INTR on GPIOZ_14 */
+		interrupts = <26 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
+&frddr_a {
+	status = "okay";
+};
+
+&frddr_b {
+	status = "okay";
+};
+
+&frddr_c {
+	status = "okay";
+};
+
+&tdmif_b {
+	status = "okay";
+};
+
+&tdmout_b {
+	status = "okay";
+};
+
+&tohdmitx {
+	status = "okay";
+};
+
+&uart_A {
+	status = "okay";
+
+	pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>;
+	pinctrl-names = "default";
+	uart-has-rtscts;
+
+	bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		shutdown-gpios = <&gpio GPIOX_17 GPIO_ACTIVE_HIGH>;
+		max-speed = <2000000>;
+		clocks = <&wifi32k>;
+		clock-names = "lpo";
+	};
+};
diff --git a/arch/arm64/boot/dts/amlogic/meson-sm1-odroid-hc4.dts b/arch/arm64/boot/dts/amlogic/meson-sm1-odroid-hc4.dts
index f3f953225bf5..e3486f60645a 100644
--- a/arch/arm64/boot/dts/amlogic/meson-sm1-odroid-hc4.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-sm1-odroid-hc4.dts
@@ -121,7 +121,7 @@
 	pinctrl-0 = <&nor_pins>;
 	pinctrl-names = "default";
 
-	spi-flash@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "jedec,spi-nor";
diff --git a/arch/arm64/boot/dts/amlogic/meson-sm1-odroid.dtsi b/arch/arm64/boot/dts/amlogic/meson-sm1-odroid.dtsi
index 5779e70caccd..ddb1b345397f 100644
--- a/arch/arm64/boot/dts/amlogic/meson-sm1-odroid.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-sm1-odroid.dtsi
@@ -48,7 +48,7 @@
 		regulator-max-microvolt = <3300000>;
 		vin-supply = <&vcc_5v>;
 
-		enable-gpio = <&gpio GPIOE_2 GPIO_ACTIVE_HIGH>;
+		enable-gpio = <&gpio_ao GPIOE_2 GPIO_OPEN_DRAIN>;
 		enable-active-high;
 		regulator-always-on;
 
@@ -225,6 +225,20 @@
 	status = "okay";
 };
 
+&cec_AO {
+	pinctrl-0 = <&cec_ao_a_h_pins>;
+	pinctrl-names = "default";
+	status = "disabled";
+	hdmi-phandle = <&hdmi_tx>;
+};
+
+&cecb_AO {
+	pinctrl-0 = <&cec_ao_b_h_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+	hdmi-phandle = <&hdmi_tx>;
+};
+
 &clkc_audio {
 	status = "okay";
 };
diff --git a/arch/arm64/boot/dts/amlogic/meson-sm1-sei610.dts b/arch/arm64/boot/dts/amlogic/meson-sm1-sei610.dts
index 427475846fc7..9068a334ea57 100644
--- a/arch/arm64/boot/dts/amlogic/meson-sm1-sei610.dts
+++ b/arch/arm64/boot/dts/amlogic/meson-sm1-sei610.dts
@@ -48,7 +48,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		key1 {
+		key-1 {
 			label = "A";
 			linux,code = <BTN_0>;
 			gpios = <&gpio GPIOH_6 GPIO_ACTIVE_LOW>;
@@ -56,7 +56,7 @@
 			interrupts = <34 IRQ_TYPE_EDGE_BOTH>;
 		};
 
-		key2 {
+		key-2 {
 			label = "B";
 			linux,code = <BTN_1>;
 			gpios = <&gpio GPIOH_7 GPIO_ACTIVE_LOW>;
@@ -64,7 +64,7 @@
 			interrupts = <35 IRQ_TYPE_EDGE_BOTH>;
 		};
 
-		key3 {
+		key-3 {
 			label = "C";
 			linux,code = <BTN_2>;
 			gpios = <&gpio_ao GPIOAO_2 GPIO_ACTIVE_LOW>;
@@ -72,7 +72,7 @@
 			interrupts = <2 IRQ_TYPE_EDGE_BOTH>;
 		};
 
-		mic_mute {
+		key-mic-mute {
 			label = "MicMute";
 			linux,code = <SW_MUTE_DEVICE>;
 			linux,input-type = <EV_SW>;
@@ -81,7 +81,7 @@
 			interrupts = <99 IRQ_TYPE_EDGE_BOTH>;
 		};
 
-		power_key {
+		key-power {
 			label = "PowerKey";
 			linux,code = <KEY_POWER>;
 			gpios = <&gpio_ao GPIOAO_3 GPIO_ACTIVE_LOW>;
@@ -171,7 +171,6 @@
 		regulator-max-microvolt = <3300000>;
 		vin-supply = <&vddao_3v3>;
 		gpio = <&gpio GPIOH_8 GPIO_OPEN_DRAIN>;
-		enable-active-low;
 		regulator-always-on;
 	};
 
@@ -203,14 +202,6 @@
 		regulator-always-on;
 	};
 
-	reserved-memory {
-		/* TEE Reserved Memory */
-		bl32_reserved: bl32@5000000 {
-			reg = <0x0 0x05300000 0x0 0x2000000>;
-			no-map;
-		};
-	};
-
 	sdio_pwrseq: sdio-pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm64/boot/dts/amlogic/meson-sm1-x96-air-gbit.dts b/arch/arm64/boot/dts/amlogic/meson-sm1-x96-air-gbit.dts
new file mode 100644
index 000000000000..7e1a74046ba5
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-sm1-x96-air-gbit.dts
@@ -0,0 +1,133 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2019 BayLibre SAS. All rights reserved.
+ * Copyright (c) 2020 Christian Hewitt <christianshewitt@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "meson-sm1-ac2xx.dtsi"
+#include <dt-bindings/sound/meson-g12a-tohdmitx.h>
+
+/ {
+	compatible = "amediatech,x96-air-gbit", "amlogic,sm1";
+	model = "Shenzhen Amediatech Technology Co., Ltd X96 Air";
+
+	sound {
+		compatible = "amlogic,axg-sound-card";
+		model = "X96-AIR";
+		audio-aux-devs = <&tdmout_b>;
+		audio-routing = "TDMOUT_B IN 0", "FRDDR_A OUT 1",
+				"TDMOUT_B IN 1", "FRDDR_B OUT 1",
+				"TDMOUT_B IN 2", "FRDDR_C OUT 1",
+				"TDM_B Playback", "TDMOUT_B OUT";
+
+		assigned-clocks = <&clkc CLKID_MPLL2>,
+				  <&clkc CLKID_MPLL0>,
+				  <&clkc CLKID_MPLL1>;
+		assigned-clock-parents = <0>, <0>, <0>;
+		assigned-clock-rates = <294912000>,
+				       <270950400>,
+				       <393216000>;
+		status = "okay";
+
+		dai-link-0 {
+			sound-dai = <&frddr_a>;
+		};
+
+		dai-link-1 {
+			sound-dai = <&frddr_b>;
+		};
+
+		dai-link-2 {
+			sound-dai = <&frddr_c>;
+		};
+
+		/* 8ch hdmi interface */
+		dai-link-3 {
+			sound-dai = <&tdmif_b>;
+			dai-format = "i2s";
+			dai-tdm-slot-tx-mask-0 = <1 1>;
+			dai-tdm-slot-tx-mask-1 = <1 1>;
+			dai-tdm-slot-tx-mask-2 = <1 1>;
+			dai-tdm-slot-tx-mask-3 = <1 1>;
+			mclk-fs = <256>;
+
+			codec {
+				sound-dai = <&tohdmitx TOHDMITX_I2S_IN_B>;
+			};
+		};
+
+		/* hdmi glue */
+		dai-link-4 {
+			sound-dai = <&tohdmitx TOHDMITX_I2S_OUT>;
+
+			codec {
+				sound-dai = <&hdmi_tx>;
+			};
+		};
+	};
+};
+
+&arb {
+	status = "okay";
+};
+
+&clkc_audio {
+	status = "okay";
+};
+
+&ethmac {
+	status = "okay";
+
+	pinctrl-0 = <&eth_pins>, <&eth_rgmii_pins>;
+	pinctrl-names = "default";
+	phy-mode = "rgmii-txid";
+	phy-handle = <&external_phy>;
+
+	rx-internal-delay-ps = <800>;
+};
+
+&ext_mdio {
+	external_phy: ethernet-phy@0 {
+		/* Realtek RTL8211F (0x001cc916) */
+		reg = <0>;
+		max-speed = <1000>;
+
+		reset-assert-us = <10000>;
+		reset-deassert-us = <80000>;
+		reset-gpios = <&gpio GPIOZ_15 (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
+
+		interrupt-parent = <&gpio_intc>;
+		/* MAC_INTR on GPIOZ_14 */
+		interrupts = <26 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
+&frddr_a {
+	status = "okay";
+};
+
+&frddr_b {
+	status = "okay";
+};
+
+&frddr_c {
+	status = "okay";
+};
+
+&ir {
+	linux,rc-map-name = "rc-x96max";
+};
+
+&tdmif_b {
+	status = "okay";
+};
+
+&tdmout_b {
+	status = "okay";
+};
+
+&tohdmitx {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/amlogic/meson-sm1-x96-air.dts b/arch/arm64/boot/dts/amlogic/meson-sm1-x96-air.dts
new file mode 100644
index 000000000000..cd93d798f2a3
--- /dev/null
+++ b/arch/arm64/boot/dts/amlogic/meson-sm1-x96-air.dts
@@ -0,0 +1,112 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2019 BayLibre SAS. All rights reserved.
+ * Copyright (c) 2020 Christian Hewitt <christianshewitt@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "meson-sm1-ac2xx.dtsi"
+#include <dt-bindings/sound/meson-g12a-tohdmitx.h>
+
+/ {
+	compatible = "amediatech,x96-air", "amlogic,sm1";
+	model = "Shenzhen Amediatech Technology Co., Ltd X96 Air";
+
+	sound {
+		compatible = "amlogic,axg-sound-card";
+		model = "X96-AIR";
+		audio-aux-devs = <&tdmout_b>;
+		audio-routing = "TDMOUT_B IN 0", "FRDDR_A OUT 1",
+				"TDMOUT_B IN 1", "FRDDR_B OUT 1",
+				"TDMOUT_B IN 2", "FRDDR_C OUT 1",
+				"TDM_B Playback", "TDMOUT_B OUT";
+
+		assigned-clocks = <&clkc CLKID_MPLL2>,
+				  <&clkc CLKID_MPLL0>,
+				  <&clkc CLKID_MPLL1>;
+		assigned-clock-parents = <0>, <0>, <0>;
+		assigned-clock-rates = <294912000>,
+				       <270950400>,
+				       <393216000>;
+		status = "okay";
+
+		dai-link-0 {
+			sound-dai = <&frddr_a>;
+		};
+
+		dai-link-1 {
+			sound-dai = <&frddr_b>;
+		};
+
+		dai-link-2 {
+			sound-dai = <&frddr_c>;
+		};
+
+		/* 8ch hdmi interface */
+		dai-link-3 {
+			sound-dai = <&tdmif_b>;
+			dai-format = "i2s";
+			dai-tdm-slot-tx-mask-0 = <1 1>;
+			dai-tdm-slot-tx-mask-1 = <1 1>;
+			dai-tdm-slot-tx-mask-2 = <1 1>;
+			dai-tdm-slot-tx-mask-3 = <1 1>;
+			mclk-fs = <256>;
+
+			codec {
+				sound-dai = <&tohdmitx TOHDMITX_I2S_IN_B>;
+			};
+		};
+
+		/* hdmi glue */
+		dai-link-4 {
+			sound-dai = <&tohdmitx TOHDMITX_I2S_OUT>;
+
+			codec {
+				sound-dai = <&hdmi_tx>;
+			};
+		};
+	};
+};
+
+&arb {
+	status = "okay";
+};
+
+&clkc_audio {
+	status = "okay";
+};
+
+&ethmac {
+	status = "okay";
+	phy-handle = <&internal_ephy>;
+	phy-mode = "rmii";
+};
+
+&frddr_a {
+	status = "okay";
+};
+
+&frddr_b {
+	status = "okay";
+};
+
+&frddr_c {
+	status = "okay";
+};
+
+&ir {
+	linux,rc-map-name = "rc-beelink-gs1";
+};
+
+&tdmif_b {
+	status = "okay";
+};
+
+&tdmout_b {
+	status = "okay";
+};
+
+&tohdmitx {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/amlogic/meson-sm1.dtsi b/arch/arm64/boot/dts/amlogic/meson-sm1.dtsi
index 3d8b1f4f2001..80737731af3f 100644
--- a/arch/arm64/boot/dts/amlogic/meson-sm1.dtsi
+++ b/arch/arm64/boot/dts/amlogic/meson-sm1.dtsi
@@ -95,26 +95,6 @@
 		compatible = "operating-points-v2";
 		opp-shared;
 
-		opp-100000000 {
-			opp-hz = /bits/ 64 <100000000>;
-			opp-microvolt = <730000>;
-		};
-
-		opp-250000000 {
-			opp-hz = /bits/ 64 <250000000>;
-			opp-microvolt = <730000>;
-		};
-
-		opp-500000000 {
-			opp-hz = /bits/ 64 <500000000>;
-			opp-microvolt = <730000>;
-		};
-
-		opp-667000000 {
-			opp-hz = /bits/ 64 <666666666>;
-			opp-microvolt = <750000>;
-		};
-
 		opp-1000000000 {
 			opp-hz = /bits/ 64 <1000000000>;
 			opp-microvolt = <770000>;
@@ -356,6 +336,33 @@
 			status = "disabled";
 		};
 
+		spdifin: audio-controller@400 {
+			compatible = "amlogic,g12a-spdifin",
+				     "amlogic,axg-spdifin";
+			reg = <0x0 0x400 0x0 0x30>;
+			#sound-dai-cells = <0>;
+			sound-name-prefix = "SPDIFIN";
+			interrupts = <GIC_SPI 151 IRQ_TYPE_EDGE_RISING>;
+			clocks = <&clkc_audio AUD_CLKID_SPDIFIN>,
+			<&clkc_audio AUD_CLKID_SPDIFIN_CLK>;
+			clock-names = "pclk", "refclk";
+			resets = <&clkc_audio AUD_RESET_SPDIFIN>;
+			status = "disabled";
+		};
+
+		spdifout_a: audio-controller@480 {
+			compatible = "amlogic,g12a-spdifout",
+				     "amlogic,axg-spdifout";
+			reg = <0x0 0x480 0x0 0x50>;
+			#sound-dai-cells = <0>;
+			sound-name-prefix = "SPDIFOUT_A";
+			clocks = <&clkc_audio AUD_CLKID_SPDIFOUT>,
+			<&clkc_audio AUD_CLKID_SPDIFOUT_CLK>;
+			clock-names = "pclk", "mclk";
+			resets = <&clkc_audio AUD_RESET_SPDIFOUT>;
+			status = "disabled";
+		};
+
 		tdmout_a: audio-controller@500 {
 			compatible = "amlogic,sm1-tdmout";
 			reg = <0x0 0x500 0x0 0x40>;
diff --git a/arch/arm64/boot/dts/apm/apm-merlin.dts b/arch/arm64/boot/dts/apm/apm-merlin.dts
index 217d7728b63a..049e7a5edca7 100644
--- a/arch/arm64/boot/dts/apm/apm-merlin.dts
+++ b/arch/arm64/boot/dts/apm/apm-merlin.dts
@@ -22,7 +22,7 @@
 
 	gpio-keys {
 		compatible = "gpio-keys";
-		button@1 {
+		button {
 			label = "POWER";
 			linux,code = <116>;
 			linux,input-type = <0x1>;
diff --git a/arch/arm64/boot/dts/apm/apm-mustang.dts b/arch/arm64/boot/dts/apm/apm-mustang.dts
index e927811ade28..efac50aeca64 100644
--- a/arch/arm64/boot/dts/apm/apm-mustang.dts
+++ b/arch/arm64/boot/dts/apm/apm-mustang.dts
@@ -22,7 +22,7 @@
 
 	gpio-keys {
 		compatible = "gpio-keys";
-		button@1 {
+		button {
 			label = "POWER";
 			linux,code = <116>;
 			linux,input-type = <0x1>;
diff --git a/arch/arm64/boot/dts/apm/apm-shadowcat.dtsi b/arch/arm64/boot/dts/apm/apm-shadowcat.dtsi
index a83c82c50e29..a8526f8157ec 100644
--- a/arch/arm64/boot/dts/apm/apm-shadowcat.dtsi
+++ b/arch/arm64/boot/dts/apm/apm-shadowcat.dtsi
@@ -597,11 +597,11 @@
 			interrupts = <0x0 0x4c 0x4>;
 		};
 
-		/* Do not change dwusb name, coded for backward compatibility */
-		usb0: dwusb@19000000 {
+		/* Node-name might need to be coded as dwusb for backward compatibility */
+		usb0: usb@19000000 {
 			status = "disabled";
 			compatible = "snps,dwc3";
-			reg =  <0x0 0x19000000 0x0 0x100000>;
+			reg = <0x0 0x19000000 0x0 0x100000>;
 			interrupts = <0x0 0x5d 0x4>;
 			dma-coherent;
 			dr_mode = "host";
diff --git a/arch/arm64/boot/dts/apm/apm-storm.dtsi b/arch/arm64/boot/dts/apm/apm-storm.dtsi
index 0f37e77f5459..f56d687f772d 100644
--- a/arch/arm64/boot/dts/apm/apm-storm.dtsi
+++ b/arch/arm64/boot/dts/apm/apm-storm.dtsi
@@ -923,20 +923,20 @@
 			phy-names = "sata-phy";
 		};
 
-		/* Do not change dwusb name, coded for backward compatibility */
-		usb0: dwusb@19000000 {
+		/* Node-name might need to be coded as dwusb for backward compatibility */
+		usb0: usb@19000000 {
 			status = "disabled";
 			compatible = "snps,dwc3";
-			reg =  <0x0 0x19000000 0x0 0x100000>;
+			reg = <0x0 0x19000000 0x0 0x100000>;
 			interrupts = <0x0 0x89 0x4>;
 			dma-coherent;
 			dr_mode = "host";
 		};
 
-		usb1: dwusb@19800000 {
+		usb1: usb@19800000 {
 			status = "disabled";
 			compatible = "snps,dwc3";
-			reg =  <0x0 0x19800000 0x0 0x100000>;
+			reg = <0x0 0x19800000 0x0 0x100000>;
 			interrupts = <0x0 0x8a 0x4>;
 			dma-coherent;
 			dr_mode = "host";
diff --git a/arch/arm64/boot/dts/apple/Makefile b/arch/arm64/boot/dts/apple/Makefile
index cbbd701ebf05..c0510c25ca6a 100644
--- a/arch/arm64/boot/dts/apple/Makefile
+++ b/arch/arm64/boot/dts/apple/Makefile
@@ -1,2 +1,6 @@
 # SPDX-License-Identifier: GPL-2.0
 dtb-$(CONFIG_ARCH_APPLE) += t8103-j274.dtb
+dtb-$(CONFIG_ARCH_APPLE) += t8103-j293.dtb
+dtb-$(CONFIG_ARCH_APPLE) += t8103-j313.dtb
+dtb-$(CONFIG_ARCH_APPLE) += t8103-j456.dtb
+dtb-$(CONFIG_ARCH_APPLE) += t8103-j457.dtb
diff --git a/arch/arm64/boot/dts/apple/t8103-j274.dts b/arch/arm64/boot/dts/apple/t8103-j274.dts
index 33a80f9501dc..c1f3ba9c39f6 100644
--- a/arch/arm64/boot/dts/apple/t8103-j274.dts
+++ b/arch/arm64/boot/dts/apple/t8103-j274.dts
@@ -10,39 +10,19 @@
 /dts-v1/;
 
 #include "t8103.dtsi"
+#include "t8103-jxxx.dtsi"
 
 / {
 	compatible = "apple,j274", "apple,t8103", "apple,arm-platform";
 	model = "Apple Mac mini (M1, 2020)";
 
 	aliases {
-		serial0 = &serial0;
 		ethernet0 = &ethernet0;
 	};
-
-	chosen {
-		#address-cells = <2>;
-		#size-cells = <2>;
-		ranges;
-
-		stdout-path = "serial0";
-
-		framebuffer0: framebuffer@0 {
-			compatible = "apple,simple-framebuffer", "simple-framebuffer";
-			reg = <0 0 0 0>; /* To be filled by loader */
-			/* Format properties will be added by loader */
-			status = "disabled";
-		};
-	};
-
-	memory@800000000 {
-		device_type = "memory";
-		reg = <0x8 0 0x2 0>; /* To be filled by loader */
-	};
 };
 
-&serial0 {
-	status = "okay";
+&wifi0 {
+	brcm,board-type = "apple,atlantisb";
 };
 
 /*
@@ -50,9 +30,6 @@
  * on-board devices and properties that are populated by the bootloader
  * (such as MAC addresses).
  */
-&port00 {
-	bus-range = <1 1>;
-};
 
 &port01 {
 	bus-range = <2 2>;
@@ -60,9 +37,13 @@
 
 &port02 {
 	bus-range = <3 3>;
-	ethernet0: pci@0,0 {
+	ethernet0: ethernet@0,0 {
 		reg = <0x30000 0x0 0x0 0x0 0x0>;
 		/* To be filled by the loader */
 		local-mac-address = [00 10 18 00 00 00];
 	};
 };
+
+&i2c2 {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/apple/t8103-j293.dts b/arch/arm64/boot/dts/apple/t8103-j293.dts
new file mode 100644
index 000000000000..ecb10d237a05
--- /dev/null
+++ b/arch/arm64/boot/dts/apple/t8103-j293.dts
@@ -0,0 +1,45 @@
+// SPDX-License-Identifier: GPL-2.0+ OR MIT
+/*
+ * Apple MacBook Pro (13-inch, M1, 2020)
+ *
+ * target-type: J293
+ *
+ * Copyright The Asahi Linux Contributors
+ */
+
+/dts-v1/;
+
+#include "t8103.dtsi"
+#include "t8103-jxxx.dtsi"
+
+/ {
+	compatible = "apple,j293", "apple,t8103", "apple,arm-platform";
+	model = "Apple MacBook Pro (13-inch, M1, 2020)";
+};
+
+&wifi0 {
+	brcm,board-type = "apple,honshu";
+};
+
+/*
+ * Remove unused PCIe ports and disable the associated DARTs.
+ */
+
+&pcie0_dart_1 {
+	status = "disabled";
+};
+
+&pcie0_dart_2 {
+	status = "disabled";
+};
+
+/delete-node/ &port01;
+/delete-node/ &port02;
+
+&i2c2 {
+	status = "okay";
+};
+
+&i2c4 {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/apple/t8103-j313.dts b/arch/arm64/boot/dts/apple/t8103-j313.dts
new file mode 100644
index 000000000000..df741737b8e6
--- /dev/null
+++ b/arch/arm64/boot/dts/apple/t8103-j313.dts
@@ -0,0 +1,37 @@
+// SPDX-License-Identifier: GPL-2.0+ OR MIT
+/*
+ * Apple MacBook Air (M1, 2020)
+ *
+ * target-type: J313
+ *
+ * Copyright The Asahi Linux Contributors
+ */
+
+/dts-v1/;
+
+#include "t8103.dtsi"
+#include "t8103-jxxx.dtsi"
+
+/ {
+	compatible = "apple,j313", "apple,t8103", "apple,arm-platform";
+	model = "Apple MacBook Air (M1, 2020)";
+};
+
+&wifi0 {
+	brcm,board-type = "apple,shikoku";
+};
+
+/*
+ * Remove unused PCIe ports and disable the associated DARTs.
+ */
+
+&pcie0_dart_1 {
+	status = "disabled";
+};
+
+&pcie0_dart_2 {
+	status = "disabled";
+};
+
+/delete-node/ &port01;
+/delete-node/ &port02;
diff --git a/arch/arm64/boot/dts/apple/t8103-j456.dts b/arch/arm64/boot/dts/apple/t8103-j456.dts
new file mode 100644
index 000000000000..8c6bf9592510
--- /dev/null
+++ b/arch/arm64/boot/dts/apple/t8103-j456.dts
@@ -0,0 +1,63 @@
+// SPDX-License-Identifier: GPL-2.0+ OR MIT
+/*
+ * Apple iMac (24-inch, 4x USB-C, M1, 2020)
+ *
+ * target-type: J456
+ *
+ * Copyright The Asahi Linux Contributors
+ */
+
+/dts-v1/;
+
+#include "t8103.dtsi"
+#include "t8103-jxxx.dtsi"
+
+/ {
+	compatible = "apple,j456", "apple,t8103", "apple,arm-platform";
+	model = "Apple iMac (24-inch, 4x USB-C, M1, 2020)";
+
+	aliases {
+		ethernet0 = &ethernet0;
+	};
+};
+
+&wifi0 {
+	brcm,board-type = "apple,capri";
+};
+
+&i2c0 {
+	hpm2: usb-pd@3b {
+		compatible = "apple,cd321x";
+		reg = <0x3b>;
+		interrupt-parent = <&pinctrl_ap>;
+		interrupts = <106 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-names = "irq";
+	};
+
+	hpm3: usb-pd@3c {
+		compatible = "apple,cd321x";
+		reg = <0x3c>;
+		interrupt-parent = <&pinctrl_ap>;
+		interrupts = <106 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-names = "irq";
+	};
+};
+
+/*
+ * Force the bus number assignments so that we can declare some of the
+ * on-board devices and properties that are populated by the bootloader
+ * (such as MAC addresses).
+ */
+
+&port01 {
+	bus-range = <2 2>;
+};
+
+&port02 {
+	bus-range = <3 3>;
+	ethernet0: ethernet@0,0 {
+		reg = <0x30000 0x0 0x0 0x0 0x0>;
+		/* To be filled by the loader */
+		local-mac-address = [00 10 18 00 00 00];
+	};
+};
diff --git a/arch/arm64/boot/dts/apple/t8103-j457.dts b/arch/arm64/boot/dts/apple/t8103-j457.dts
new file mode 100644
index 000000000000..fe7c0aaf7d62
--- /dev/null
+++ b/arch/arm64/boot/dts/apple/t8103-j457.dts
@@ -0,0 +1,51 @@
+// SPDX-License-Identifier: GPL-2.0+ OR MIT
+/*
+ * Apple iMac (24-inch, 2x USB-C, M1, 2020)
+ *
+ * target-type: J457
+ *
+ * Copyright The Asahi Linux Contributors
+ */
+
+/dts-v1/;
+
+#include "t8103.dtsi"
+#include "t8103-jxxx.dtsi"
+
+/ {
+	compatible = "apple,j457", "apple,t8103", "apple,arm-platform";
+	model = "Apple iMac (24-inch, 2x USB-C, M1, 2020)";
+
+	aliases {
+		ethernet0 = &ethernet0;
+	};
+};
+
+&wifi0 {
+	brcm,board-type = "apple,santorini";
+};
+
+/*
+ * Force the bus number assignments so that we can declare some of the
+ * on-board devices and properties that are populated by the bootloader
+ * (such as MAC addresses).
+ */
+
+&port02 {
+	bus-range = <3 3>;
+	ethernet0: ethernet@0,0 {
+		reg = <0x30000 0x0 0x0 0x0 0x0>;
+		/* To be filled by the loader */
+		local-mac-address = [00 10 18 00 00 00];
+	};
+};
+
+/*
+ * Remove unused PCIe port and disable the associated DART.
+ */
+
+&pcie0_dart_1 {
+	status = "disabled";
+};
+
+/delete-node/ &port01;
diff --git a/arch/arm64/boot/dts/apple/t8103-jxxx.dtsi b/arch/arm64/boot/dts/apple/t8103-jxxx.dtsi
new file mode 100644
index 000000000000..3d15b8e2a6c1
--- /dev/null
+++ b/arch/arm64/boot/dts/apple/t8103-jxxx.dtsi
@@ -0,0 +1,80 @@
+// SPDX-License-Identifier: GPL-2.0+ OR MIT
+/*
+ * Apple M1 Mac mini, MacBook Air/Pro, iMac 24" (M1, 2020/2021)
+ *
+ * This file contains parts common to all Apple M1 devices using the t8103.
+ *
+ * target-type: J274, J293, J313, J456, J457
+ *
+ * Copyright The Asahi Linux Contributors
+ */
+
+/ {
+	aliases {
+		serial0 = &serial0;
+		serial2 = &serial2;
+		wifi0 = &wifi0;
+	};
+
+	chosen {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		stdout-path = "serial0";
+
+		framebuffer0: framebuffer@0 {
+			compatible = "apple,simple-framebuffer", "simple-framebuffer";
+			reg = <0 0 0 0>; /* To be filled by loader */
+			/* Format properties will be added by loader */
+			status = "disabled";
+		};
+	};
+
+	memory@800000000 {
+		device_type = "memory";
+		reg = <0x8 0 0x2 0>; /* To be filled by loader */
+	};
+};
+
+&serial0 {
+	status = "okay";
+};
+
+&serial2 {
+	status = "okay";
+};
+
+&i2c0 {
+	hpm0: usb-pd@38 {
+		compatible = "apple,cd321x";
+		reg = <0x38>;
+		interrupt-parent = <&pinctrl_ap>;
+		interrupts = <106 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-names = "irq";
+	};
+
+	hpm1: usb-pd@3f {
+		compatible = "apple,cd321x";
+		reg = <0x3f>;
+		interrupt-parent = <&pinctrl_ap>;
+		interrupts = <106 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-names = "irq";
+	};
+};
+
+/*
+ * Force the bus number assignments so that we can declare some of the
+ * on-board devices and properties that are populated by the bootloader
+ * (such as MAC addresses).
+ */
+&port00 {
+	bus-range = <1 1>;
+	wifi0: network@0,0 {
+		compatible = "pci14e4,4425";
+		reg = <0x10000 0x0 0x0 0x0 0x0>;
+		/* To be filled by the loader */
+		local-mac-address = [00 00 00 00 00 00];
+		apple,antenna-sku = "XX";
+	};
+};
diff --git a/arch/arm64/boot/dts/apple/t8103-pmgr.dtsi b/arch/arm64/boot/dts/apple/t8103-pmgr.dtsi
new file mode 100644
index 000000000000..a6dbb1f485d8
--- /dev/null
+++ b/arch/arm64/boot/dts/apple/t8103-pmgr.dtsi
@@ -0,0 +1,1133 @@
+// SPDX-License-Identifier: GPL-2.0+ OR MIT
+/*
+ * PMGR Power domains for the Apple T8103 "M1" SoC
+ *
+ * Copyright The Asahi Linux Contributors
+ */
+
+
+&pmgr {
+	ps_sbr: power-controller@100 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x100 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "sbr";
+		apple,always-on; /* Core device */
+	};
+
+	ps_aic: power-controller@108 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x108 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "aic";
+		apple,always-on; /* Core device */
+	};
+
+	ps_dwi: power-controller@110 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x110 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "dwi";
+		apple,always-on; /* Core device */
+	};
+
+	ps_soc_spmi0: power-controller@118 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x118 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "soc_spmi0";
+	};
+
+	ps_soc_spmi1: power-controller@120 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x120 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "soc_spmi1";
+	};
+
+	ps_soc_spmi2: power-controller@128 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x128 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "soc_spmi2";
+	};
+
+	ps_gpio: power-controller@130 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x130 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "gpio";
+	};
+
+	ps_pms_busif: power-controller@138 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x138 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "pms_busif";
+		apple,always-on; /* Core device */
+	};
+
+	ps_pms: power-controller@140 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x140 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "pms";
+		apple,always-on; /* Core device */
+	};
+
+	ps_pms_fpwm0: power-controller@148 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x148 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "pms_fpwm0";
+		power-domains = <&ps_pms>;
+	};
+
+	ps_pms_fpwm1: power-controller@150 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x150 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "pms_fpwm1";
+		power-domains = <&ps_pms>;
+	};
+
+	ps_pms_fpwm2: power-controller@158 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x158 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "pms_fpwm2";
+		power-domains = <&ps_pms>;
+	};
+
+	ps_pms_fpwm3: power-controller@160 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x160 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "pms_fpwm3";
+		power-domains = <&ps_pms>;
+	};
+
+	ps_pms_fpwm4: power-controller@168 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x168 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "pms_fpwm4";
+		power-domains = <&ps_pms>;
+	};
+
+	ps_soc_dpe: power-controller@170 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x170 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "soc_dpe";
+		apple,always-on; /* Core device */
+	};
+
+	ps_pmgr_soc_ocla: power-controller@178 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x178 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "pmgr_soc_ocla";
+	};
+
+	ps_ispsens0: power-controller@180 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x180 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "ispsens0";
+	};
+
+	ps_ispsens1: power-controller@188 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x188 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "ispsens1";
+	};
+
+	ps_ispsens2: power-controller@190 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x190 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "ispsens2";
+	};
+
+	ps_ispsens3: power-controller@198 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x198 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "ispsens3";
+	};
+
+	ps_pcie_ref: power-controller@1a0 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x1a0 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "pcie_ref";
+	};
+
+	ps_aft0: power-controller@1a8 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x1a8 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "aft0";
+	};
+
+	ps_devc0_ivdmc: power-controller@1b0 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x1b0 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "devc0_ivdmc";
+	};
+
+	ps_imx: power-controller@1b8 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x1b8 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "imx";
+		apple,always-on; /* Apple fabric, critical block */
+	};
+
+	ps_sio_busif: power-controller@1c0 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x1c0 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "sio_busif";
+	};
+
+	ps_sio: power-controller@1c8 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x1c8 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "sio";
+		power-domains = <&ps_sio_busif>;
+	};
+
+	ps_sio_cpu: power-controller@1d0 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x1d0 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "sio_cpu";
+		power-domains = <&ps_sio>;
+	};
+
+	ps_fpwm0: power-controller@1d8 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x1d8 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "fpwm0";
+	};
+
+	ps_fpwm1: power-controller@1e0 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x1e0 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "fpwm1";
+	};
+
+	ps_fpwm2: power-controller@1e8 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x1e8 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "fpwm2";
+	};
+
+	ps_i2c0: power-controller@1f0 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x1f0 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "i2c0";
+		power-domains = <&ps_sio>;
+	};
+
+	ps_i2c1: power-controller@1f8 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x1f8 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "i2c1";
+		power-domains = <&ps_sio>;
+	};
+
+	ps_i2c2: power-controller@200 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x200 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "i2c2";
+		power-domains = <&ps_sio>;
+	};
+
+	ps_i2c3: power-controller@208 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x208 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "i2c3";
+		power-domains = <&ps_sio>;
+	};
+
+	ps_i2c4: power-controller@210 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x210 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "i2c4";
+		power-domains = <&ps_sio>;
+	};
+
+	ps_spi_p: power-controller@218 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x218 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "spi_p";
+		power-domains = <&ps_sio>;
+	};
+
+	ps_uart_p: power-controller@220 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x220 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "uart_p";
+		power-domains = <&ps_sio>;
+	};
+
+	ps_audio_p: power-controller@228 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x228 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "audio_p";
+		power-domains = <&ps_sio>;
+	};
+
+	ps_sio_adma: power-controller@230 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x230 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "sio_adma";
+		power-domains = <&ps_sio>, <&ps_pms>;
+	};
+
+	ps_aes: power-controller@238 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x238 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "aes";
+		power-domains = <&ps_sio>;
+	};
+
+	ps_spi0: power-controller@240 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x240 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "spi0";
+		power-domains = <&ps_sio>, <&ps_spi_p>;
+	};
+
+	ps_spi1: power-controller@248 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x248 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "spi1";
+		power-domains = <&ps_sio>, <&ps_spi_p>;
+	};
+
+	ps_spi2: power-controller@250 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x250 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "spi2";
+		power-domains = <&ps_sio>, <&ps_spi_p>;
+	};
+
+	ps_spi3: power-controller@258 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x258 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "spi3";
+		power-domains = <&ps_sio>, <&ps_spi_p>;
+	};
+
+	ps_uart_n: power-controller@268 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x268 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "uart_n";
+		power-domains = <&ps_uart_p>;
+	};
+
+	ps_uart0: power-controller@270 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x270 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "uart0";
+		power-domains = <&ps_uart_p>;
+	};
+
+	ps_uart1: power-controller@278 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x278 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "uart1";
+		power-domains = <&ps_uart_p>;
+	};
+
+	ps_uart2: power-controller@280 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x280 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "uart2";
+		power-domains = <&ps_uart_p>;
+	};
+
+	ps_uart3: power-controller@288 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x288 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "uart3";
+		power-domains = <&ps_uart_p>;
+	};
+
+	ps_uart4: power-controller@290 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x290 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "uart4";
+		power-domains = <&ps_uart_p>;
+	};
+
+	ps_uart5: power-controller@298 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x298 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "uart5";
+		power-domains = <&ps_uart_p>;
+	};
+
+	ps_uart6: power-controller@2a0 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x2a0 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "uart6";
+		power-domains = <&ps_uart_p>;
+	};
+
+	ps_uart7: power-controller@2a8 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x2a8 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "uart7";
+		power-domains = <&ps_uart_p>;
+	};
+
+	ps_uart8: power-controller@2b0 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x2b0 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "uart8";
+		power-domains = <&ps_uart_p>;
+	};
+
+	ps_mca0: power-controller@2b8 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x2b8 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "mca0";
+		power-domains = <&ps_audio_p>, <&ps_sio_adma>;
+	};
+
+	ps_mca1: power-controller@2c0 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x2c0 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "mca1";
+		power-domains = <&ps_audio_p>, <&ps_sio_adma>;
+	};
+
+	ps_mca2: power-controller@2c8 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x2c8 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "mca2";
+		power-domains = <&ps_audio_p>, <&ps_sio_adma>;
+	};
+
+	ps_mca3: power-controller@2d0 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x2d0 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "mca3";
+		power-domains = <&ps_audio_p>, <&ps_sio_adma>;
+	};
+
+	ps_mca4: power-controller@2d8 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x2d8 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "mca4";
+		power-domains = <&ps_audio_p>, <&ps_sio_adma>;
+	};
+
+	ps_mca5: power-controller@2e0 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x2e0 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "mca5";
+		power-domains = <&ps_audio_p>, <&ps_sio_adma>;
+	};
+
+	ps_dpa0: power-controller@2e8 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x2e8 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "dpa0";
+		power-domains = <&ps_audio_p>;
+	};
+
+	ps_dpa1: power-controller@2f0 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x2f0 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "dpa1";
+		power-domains = <&ps_audio_p>;
+	};
+
+	ps_mcc: power-controller@2f8 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x2f8 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "mcc";
+		apple,always-on; /* Memory controller */
+	};
+
+	ps_spi4: power-controller@260 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x260 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "spi4";
+		power-domains = <&ps_sio>, <&ps_spi_p>;
+	};
+
+	ps_dcs0: power-controller@300 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x300 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "dcs0";
+		apple,always-on; /* LPDDR4 interface */
+	};
+
+	ps_dcs1: power-controller@310 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x310 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "dcs1";
+		apple,always-on; /* LPDDR4 interface */
+	};
+
+	ps_dcs2: power-controller@308 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x308 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "dcs2";
+		apple,always-on; /* LPDDR4 interface */
+	};
+
+	ps_dcs3: power-controller@318 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x318 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "dcs3";
+		apple,always-on; /* LPDDR4 interface */
+	};
+
+	ps_smx: power-controller@340 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x340 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "smx";
+		apple,always-on; /* Apple fabric, critical block */
+	};
+
+	ps_apcie: power-controller@348 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x348 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "apcie";
+		power-domains = <&ps_imx>, <&ps_pcie_ref>;
+	};
+
+	ps_rmx: power-controller@350 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x350 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "rmx";
+		/* Apple Fabric, display/image stuff: this can power down */
+	};
+
+	ps_mmx: power-controller@358 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x358 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "mmx";
+		/* Apple Fabric, media stuff: this can power down */
+	};
+
+	ps_disp0_fe: power-controller@360 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x360 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "disp0_fe";
+		power-domains = <&ps_rmx>;
+		apple,always-on; /* TODO: figure out if we can enable PM here */
+	};
+
+	ps_dispext_fe: power-controller@368 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x368 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "dispext_fe";
+		power-domains = <&ps_rmx>;
+	};
+
+	ps_dispext_cpu0: power-controller@378 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x378 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "dispext_cpu0";
+		power-domains = <&ps_dispext_fe>;
+		apple,min-state = <4>;
+	};
+
+	ps_jpg: power-controller@3c0 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x3c0 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "jpg";
+		power-domains = <&ps_mmx>;
+	};
+
+	ps_msr: power-controller@3c8 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x3c8 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "msr";
+		power-domains = <&ps_mmx>;
+	};
+
+	ps_msr_ase_core: power-controller@3d0 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x3d0 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "msr_ase_core";
+	};
+
+	ps_pmp: power-controller@3d8 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x3d8 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "pmp";
+	};
+
+	ps_pms_sram: power-controller@3e0 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x3e0 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "pms_sram";
+	};
+
+	ps_apcie_gp: power-controller@3e8 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x3e8 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "apcie_gp";
+		power-domains = <&ps_apcie>;
+	};
+
+	ps_ans2: power-controller@3f0 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x3f0 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "ans2";
+	};
+
+	ps_gfx: power-controller@3f8 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x3f8 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "gfx";
+	};
+
+	ps_dcs4: power-controller@320 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x320 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "dcs4";
+		apple,always-on; /* LPDDR4 interface */
+	};
+
+	ps_dcs5: power-controller@330 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x330 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "dcs5";
+		apple,always-on; /* LPDDR4 interface */
+	};
+
+	ps_dcs6: power-controller@328 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x328 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "dcs6";
+		apple,always-on; /* LPDDR4 interface */
+	};
+
+	ps_dcs7: power-controller@338 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x338 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "dcs7";
+		apple,always-on; /* LPDDR4 interface */
+	};
+
+	ps_dispdfr_fe: power-controller@3a8 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x3a8 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "dispdfr_fe";
+		power-domains = <&ps_rmx>;
+	};
+
+	ps_dispdfr_be: power-controller@3b0 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x3b0 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "dispdfr_be";
+		power-domains = <&ps_dispdfr_fe>;
+	};
+
+	ps_mipi_dsi: power-controller@3b8 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x3b8 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "mipi_dsi";
+		power-domains = <&ps_dispdfr_be>;
+	};
+
+	ps_isp_sys: power-controller@400 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x400 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "isp_sys";
+		power-domains = <&ps_rmx>;
+	};
+
+	ps_venc_sys: power-controller@408 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x408 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "venc_sys";
+		power-domains = <&ps_mmx>;
+	};
+
+	ps_avd_sys: power-controller@410 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x410 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "avd_sys";
+		power-domains = <&ps_mmx>;
+	};
+
+	ps_apcie_st: power-controller@418 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x418 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "apcie_st";
+		power-domains = <&ps_apcie>, <&ps_ans2>;
+	};
+
+	ps_ane_sys: power-controller@470 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x470 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "ane_sys";
+	};
+
+	ps_atc0_common: power-controller@420 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x420 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "atc0_common";
+	};
+
+	ps_atc0_pcie: power-controller@428 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x428 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "atc0_pcie";
+		power-domains = <&ps_atc0_common>;
+	};
+
+	ps_atc0_cio: power-controller@430 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x430 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "atc0_cio";
+		power-domains = <&ps_atc0_common>;
+	};
+
+	ps_atc0_cio_pcie: power-controller@438 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x438 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "atc0_cio_pcie";
+		power-domains = <&ps_atc0_cio>;
+	};
+
+	ps_atc0_cio_usb: power-controller@440 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x440 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "atc0_cio_usb";
+		power-domains = <&ps_atc0_cio>;
+	};
+
+	ps_atc1_common: power-controller@448 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x448 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "atc1_common";
+	};
+
+	ps_atc1_pcie: power-controller@450 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x450 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "atc1_pcie";
+		power-domains = <&ps_atc1_common>;
+	};
+
+	ps_atc1_cio: power-controller@458 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x458 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "atc1_cio";
+		power-domains = <&ps_atc1_common>;
+	};
+
+	ps_atc1_cio_pcie: power-controller@460 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x460 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "atc1_cio_pcie";
+		power-domains = <&ps_atc1_cio>;
+	};
+
+	ps_atc1_cio_usb: power-controller@468 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x468 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "atc1_cio_usb";
+		power-domains = <&ps_atc1_cio>;
+	};
+
+	ps_sep: power-controller@c00 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0xc00 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "sep";
+		apple,always-on; /* Locked on */
+	};
+
+	ps_venc_dma: power-controller@8000 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x8000 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "venc_dma";
+		power-domains = <&ps_venc_sys>;
+	};
+
+	ps_venc_pipe4: power-controller@8008 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x8008 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "venc_pipe4";
+		power-domains = <&ps_venc_dma>;
+	};
+
+	ps_venc_pipe5: power-controller@8010 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x8010 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "venc_pipe5";
+		power-domains = <&ps_venc_dma>;
+	};
+
+	ps_venc_me0: power-controller@8018 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x8018 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "venc_me0";
+		power-domains = <&ps_venc_pipe4>, <&ps_venc_pipe5>;
+	};
+
+	ps_venc_me1: power-controller@8020 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x8020 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "venc_me1";
+		power-domains = <&ps_venc_pipe4>, <&ps_venc_pipe5>;
+	};
+
+	ps_ane_sys_cpu: power-controller@c000 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0xc000 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "ane_sys_cpu";
+		power-domains = <&ps_ane_sys>;
+	};
+
+	ps_disp0_cpu0: power-controller@10018 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x10018 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "disp0_cpu0";
+		power-domains = <&ps_disp0_fe>;
+		apple,always-on; /* TODO: figure out if we can enable PM here */
+		apple,min-state = <4>;
+	};
+};
+
+&pmgr_mini {
+	ps_debug: power-controller@58 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x58 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "debug";
+		apple,always-on; /* Core AON device */
+	};
+
+	ps_nub_spmi0: power-controller@60 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x60 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "nub_spmi0";
+		apple,always-on; /* Core AON device */
+	};
+
+	ps_nub_aon: power-controller@70 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x70 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "nub_aon";
+		apple,always-on; /* Core AON device */
+	};
+
+	ps_nub_gpio: power-controller@80 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x80 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "nub_gpio";
+		apple,always-on; /* Core AON device */
+	};
+
+	ps_nub_fabric: power-controller@a8 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0xa8 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "nub_fabric";
+		apple,always-on; /* Core AON device */
+	};
+
+	ps_nub_sram: power-controller@b0 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0xb0 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "nub_sram";
+		apple,always-on; /* Core AON device */
+	};
+
+	ps_debug_usb: power-controller@b8 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0xb8 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "debug_usb";
+		apple,always-on; /* Core AON device */
+		power-domains = <&ps_debug>;
+	};
+
+	ps_debug_auth: power-controller@c0 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0xc0 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "debug_auth";
+		apple,always-on; /* Core AON device */
+		power-domains = <&ps_debug>;
+	};
+
+	ps_nub_spmi1: power-controller@68 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x68 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "nub_spmi1";
+		apple,always-on; /* Core AON device */
+	};
+
+	ps_msg: power-controller@78 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x78 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "msg";
+	};
+
+	ps_atc0_usb_aon: power-controller@88 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x88 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "atc0_usb_aon";
+	};
+
+	ps_atc1_usb_aon: power-controller@90 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x90 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "atc1_usb_aon";
+	};
+
+	ps_atc0_usb: power-controller@98 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0x98 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "atc0_usb";
+		power-domains = <&ps_atc0_usb_aon>, <&ps_atc0_common>;
+	};
+
+	ps_atc1_usb: power-controller@a0 {
+		compatible = "apple,t8103-pmgr-pwrstate", "apple,pmgr-pwrstate";
+		reg = <0xa0 4>;
+		#power-domain-cells = <0>;
+		#reset-cells = <0>;
+		label = "atc1_usb";
+		power-domains = <&ps_atc1_usb_aon>, <&ps_atc1_common>;
+	};
+};
diff --git a/arch/arm64/boot/dts/apple/t8103.dtsi b/arch/arm64/boot/dts/apple/t8103.dtsi
index e22c9433d5e0..51a63b29d404 100644
--- a/arch/arm64/boot/dts/apple/t8103.dtsi
+++ b/arch/arm64/boot/dts/apple/t8103.dtsi
@@ -97,11 +97,23 @@
 			     <AIC_FIQ AIC_TMR_HV_VIRT IRQ_TYPE_LEVEL_HIGH>;
 	};
 
-	clk24: clock-24m {
+	pmu-e {
+		compatible = "apple,icestorm-pmu";
+		interrupt-parent = <&aic>;
+		interrupts = <AIC_FIQ AIC_CPU_PMU_E IRQ_TYPE_LEVEL_HIGH>;
+	};
+
+	pmu-p {
+		compatible = "apple,firestorm-pmu";
+		interrupt-parent = <&aic>;
+		interrupts = <AIC_FIQ AIC_CPU_PMU_P IRQ_TYPE_LEVEL_HIGH>;
+	};
+
+	clkref: clock-ref {
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
 		clock-frequency = <24000000>;
-		clock-output-names = "clk24";
+		clock-output-names = "clkref";
 	};
 
 	soc {
@@ -112,6 +124,73 @@
 		ranges;
 		nonposted-mmio;
 
+		i2c0: i2c@235010000 {
+			compatible = "apple,t8103-i2c", "apple,i2c";
+			reg = <0x2 0x35010000 0x0 0x4000>;
+			clocks = <&clkref>;
+			interrupt-parent = <&aic>;
+			interrupts = <AIC_IRQ 627 IRQ_TYPE_LEVEL_HIGH>;
+			pinctrl-0 = <&i2c0_pins>;
+			pinctrl-names = "default";
+			#address-cells = <0x1>;
+			#size-cells = <0x0>;
+			power-domains = <&ps_i2c0>;
+		};
+
+		i2c1: i2c@235014000 {
+			compatible = "apple,t8103-i2c", "apple,i2c";
+			reg = <0x2 0x35014000 0x0 0x4000>;
+			clocks = <&clkref>;
+			interrupt-parent = <&aic>;
+			interrupts = <AIC_IRQ 628 IRQ_TYPE_LEVEL_HIGH>;
+			pinctrl-0 = <&i2c1_pins>;
+			pinctrl-names = "default";
+			#address-cells = <0x1>;
+			#size-cells = <0x0>;
+			power-domains = <&ps_i2c1>;
+		};
+
+		i2c2: i2c@235018000 {
+			compatible = "apple,t8103-i2c", "apple,i2c";
+			reg = <0x2 0x35018000 0x0 0x4000>;
+			clocks = <&clkref>;
+			interrupt-parent = <&aic>;
+			interrupts = <AIC_IRQ 629 IRQ_TYPE_LEVEL_HIGH>;
+			pinctrl-0 = <&i2c2_pins>;
+			pinctrl-names = "default";
+			#address-cells = <0x1>;
+			#size-cells = <0x0>;
+			status = "disabled"; /* not used in all devices */
+			power-domains = <&ps_i2c2>;
+		};
+
+		i2c3: i2c@23501c000 {
+			compatible = "apple,t8103-i2c", "apple,i2c";
+			reg = <0x2 0x3501c000 0x0 0x4000>;
+			clocks = <&clkref>;
+			interrupt-parent = <&aic>;
+			interrupts = <AIC_IRQ 630 IRQ_TYPE_LEVEL_HIGH>;
+			pinctrl-0 = <&i2c3_pins>;
+			pinctrl-names = "default";
+			#address-cells = <0x1>;
+			#size-cells = <0x0>;
+			power-domains = <&ps_i2c3>;
+		};
+
+		i2c4: i2c@235020000 {
+			compatible = "apple,t8103-i2c", "apple,i2c";
+			reg = <0x2 0x35020000 0x0 0x4000>;
+			clocks = <&clkref>;
+			interrupt-parent = <&aic>;
+			interrupts = <AIC_IRQ 631 IRQ_TYPE_LEVEL_HIGH>;
+			pinctrl-0 = <&i2c4_pins>;
+			pinctrl-names = "default";
+			#address-cells = <0x1>;
+			#size-cells = <0x0>;
+			power-domains = <&ps_i2c4>;
+			status = "disabled"; /* only used in J293 */
+		};
+
 		serial0: serial@235200000 {
 			compatible = "apple,s5l-uart";
 			reg = <0x2 0x35200000 0x0 0x1000>;
@@ -122,8 +201,21 @@
 			 * TODO: figure out the clocking properly, there may
 			 * be a third selectable clock.
 			 */
-			clocks = <&clk24>, <&clk24>;
+			clocks = <&clkref>, <&clkref>;
 			clock-names = "uart", "clk_uart_baud0";
+			power-domains = <&ps_uart0>;
+			status = "disabled";
+		};
+
+		serial2: serial@235208000 {
+			compatible = "apple,s5l-uart";
+			reg = <0x2 0x35208000 0x0 0x1000>;
+			reg-io-width = <4>;
+			interrupt-parent = <&aic>;
+			interrupts = <AIC_IRQ 607 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clkref>, <&clkref>;
+			clock-names = "uart", "clk_uart_baud0";
+			power-domains = <&ps_uart2>;
 			status = "disabled";
 		};
 
@@ -132,11 +224,32 @@
 			#interrupt-cells = <3>;
 			interrupt-controller;
 			reg = <0x2 0x3b100000 0x0 0x8000>;
+			power-domains = <&ps_aic>;
+
+			affinities {
+				e-core-pmu-affinity {
+					apple,fiq-index = <AIC_CPU_PMU_E>;
+					cpus = <&cpu0 &cpu1 &cpu2 &cpu3>;
+				};
+
+				p-core-pmu-affinity {
+					apple,fiq-index = <AIC_CPU_PMU_P>;
+					cpus = <&cpu4 &cpu5 &cpu6 &cpu7>;
+				};
+			};
+		};
+
+		pmgr: power-management@23b700000 {
+			compatible = "apple,t8103-pmgr", "apple,pmgr", "syscon", "simple-mfd";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			reg = <0x2 0x3b700000 0 0x14000>;
 		};
 
 		pinctrl_ap: pinctrl@23c100000 {
 			compatible = "apple,t8103-pinctrl", "apple,pinctrl";
 			reg = <0x2 0x3c100000 0x0 0x100000>;
+			power-domains = <&ps_gpio>;
 
 			gpio-controller;
 			#gpio-cells = <2>;
@@ -144,6 +257,7 @@
 			apple,npins = <212>;
 
 			interrupt-controller;
+			#interrupt-cells = <2>;
 			interrupt-parent = <&aic>;
 			interrupts = <AIC_IRQ 190 IRQ_TYPE_LEVEL_HIGH>,
 				     <AIC_IRQ 191 IRQ_TYPE_LEVEL_HIGH>,
@@ -153,6 +267,31 @@
 				     <AIC_IRQ 195 IRQ_TYPE_LEVEL_HIGH>,
 				     <AIC_IRQ 196 IRQ_TYPE_LEVEL_HIGH>;
 
+			i2c0_pins: i2c0-pins {
+				pinmux = <APPLE_PINMUX(192, 1)>,
+					 <APPLE_PINMUX(188, 1)>;
+			};
+
+			i2c1_pins: i2c1-pins {
+				pinmux = <APPLE_PINMUX(201, 1)>,
+					 <APPLE_PINMUX(199, 1)>;
+			};
+
+			i2c2_pins: i2c2-pins {
+				pinmux = <APPLE_PINMUX(163, 1)>,
+					 <APPLE_PINMUX(162, 1)>;
+			};
+
+			i2c3_pins: i2c3-pins {
+				pinmux = <APPLE_PINMUX(73, 1)>,
+					 <APPLE_PINMUX(72, 1)>;
+			};
+
+			i2c4_pins: i2c4-pins {
+				pinmux = <APPLE_PINMUX(135, 1)>,
+					 <APPLE_PINMUX(134, 1)>;
+			};
+
 			pcie_pins: pcie-pins {
 				pinmux = <APPLE_PINMUX(150, 1)>,
 					 <APPLE_PINMUX(151, 1)>,
@@ -160,29 +299,10 @@
 			};
 		};
 
-		pinctrl_aop: pinctrl@24a820000 {
-			compatible = "apple,t8103-pinctrl", "apple,pinctrl";
-			reg = <0x2 0x4a820000 0x0 0x4000>;
-
-			gpio-controller;
-			#gpio-cells = <2>;
-			gpio-ranges = <&pinctrl_aop 0 0 42>;
-			apple,npins = <42>;
-
-			interrupt-controller;
-			interrupt-parent = <&aic>;
-			interrupts = <AIC_IRQ 268 IRQ_TYPE_LEVEL_HIGH>,
-				     <AIC_IRQ 269 IRQ_TYPE_LEVEL_HIGH>,
-				     <AIC_IRQ 270 IRQ_TYPE_LEVEL_HIGH>,
-				     <AIC_IRQ 271 IRQ_TYPE_LEVEL_HIGH>,
-				     <AIC_IRQ 272 IRQ_TYPE_LEVEL_HIGH>,
-				     <AIC_IRQ 273 IRQ_TYPE_LEVEL_HIGH>,
-				     <AIC_IRQ 274 IRQ_TYPE_LEVEL_HIGH>;
-		};
-
 		pinctrl_nub: pinctrl@23d1f0000 {
 			compatible = "apple,t8103-pinctrl", "apple,pinctrl";
 			reg = <0x2 0x3d1f0000 0x0 0x4000>;
+			power-domains = <&ps_nub_gpio>;
 
 			gpio-controller;
 			#gpio-cells = <2>;
@@ -190,6 +310,7 @@
 			apple,npins = <23>;
 
 			interrupt-controller;
+			#interrupt-cells = <2>;
 			interrupt-parent = <&aic>;
 			interrupts = <AIC_IRQ 330 IRQ_TYPE_LEVEL_HIGH>,
 				     <AIC_IRQ 331 IRQ_TYPE_LEVEL_HIGH>,
@@ -200,6 +321,21 @@
 				     <AIC_IRQ 336 IRQ_TYPE_LEVEL_HIGH>;
 		};
 
+		pmgr_mini: power-management@23d280000 {
+			compatible = "apple,t8103-pmgr", "apple,pmgr", "syscon", "simple-mfd";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			reg = <0x2 0x3d280000 0 0x4000>;
+		};
+
+		wdt: watchdog@23d2b0000 {
+			compatible = "apple,t8103-wdt", "apple,wdt";
+			reg = <0x2 0x3d2b0000 0x0 0x4000>;
+			clocks = <&clkref>;
+			interrupt-parent = <&aic>;
+			interrupts = <AIC_IRQ 338 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
 		pinctrl_smc: pinctrl@23e820000 {
 			compatible = "apple,t8103-pinctrl", "apple,pinctrl";
 			reg = <0x2 0x3e820000 0x0 0x4000>;
@@ -210,6 +346,7 @@
 			apple,npins = <16>;
 
 			interrupt-controller;
+			#interrupt-cells = <2>;
 			interrupt-parent = <&aic>;
 			interrupts = <AIC_IRQ 391 IRQ_TYPE_LEVEL_HIGH>,
 				     <AIC_IRQ 392 IRQ_TYPE_LEVEL_HIGH>,
@@ -220,12 +357,68 @@
 				     <AIC_IRQ 397 IRQ_TYPE_LEVEL_HIGH>;
 		};
 
+		pinctrl_aop: pinctrl@24a820000 {
+			compatible = "apple,t8103-pinctrl", "apple,pinctrl";
+			reg = <0x2 0x4a820000 0x0 0x4000>;
+
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&pinctrl_aop 0 0 42>;
+			apple,npins = <42>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			interrupt-parent = <&aic>;
+			interrupts = <AIC_IRQ 268 IRQ_TYPE_LEVEL_HIGH>,
+				     <AIC_IRQ 269 IRQ_TYPE_LEVEL_HIGH>,
+				     <AIC_IRQ 270 IRQ_TYPE_LEVEL_HIGH>,
+				     <AIC_IRQ 271 IRQ_TYPE_LEVEL_HIGH>,
+				     <AIC_IRQ 272 IRQ_TYPE_LEVEL_HIGH>,
+				     <AIC_IRQ 273 IRQ_TYPE_LEVEL_HIGH>,
+				     <AIC_IRQ 274 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		ans_mbox: mbox@277408000 {
+			compatible = "apple,t8103-asc-mailbox", "apple,asc-mailbox-v4";
+			reg = <0x2 0x77408000 0x0 0x4000>;
+			interrupt-parent = <&aic>;
+			interrupts = <AIC_IRQ 583 IRQ_TYPE_LEVEL_HIGH>,
+				<AIC_IRQ 584 IRQ_TYPE_LEVEL_HIGH>,
+				<AIC_IRQ 585 IRQ_TYPE_LEVEL_HIGH>,
+				<AIC_IRQ 586 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "send-empty", "send-not-empty",
+				"recv-empty", "recv-not-empty";
+			#mbox-cells = <0>;
+			power-domains = <&ps_ans2>;
+		};
+
+		sart: iommu@27bc50000 {
+			compatible = "apple,t8103-sart";
+			reg = <0x2 0x7bc50000 0x0 0x10000>;
+			power-domains = <&ps_ans2>;
+		};
+
+		nvme@27bcc0000 {
+			compatible = "apple,t8103-nvme-ans2", "apple,nvme-ans2";
+			reg = <0x2 0x7bcc0000 0x0 0x40000>,
+				<0x2 0x77400000 0x0 0x4000>;
+			reg-names = "nvme", "ans";
+			interrupt-parent = <&aic>;
+			interrupts = <AIC_IRQ 590 IRQ_TYPE_LEVEL_HIGH>;
+			mboxes = <&ans_mbox>;
+			apple,sart = <&sart>;
+			power-domains = <&ps_ans2>, <&ps_apcie_st>;
+			power-domain-names = "ans", "apcie0";
+			resets = <&ps_ans2>;
+		};
+
 		pcie0_dart_0: dart@681008000 {
 			compatible = "apple,t8103-dart";
 			reg = <0x6 0x81008000 0x0 0x4000>;
 			#iommu-cells = <1>;
 			interrupt-parent = <&aic>;
 			interrupts = <AIC_IRQ 696 IRQ_TYPE_LEVEL_HIGH>;
+			power-domains = <&ps_apcie_gp>;
 		};
 
 		pcie0_dart_1: dart@682008000 {
@@ -234,6 +427,7 @@
 			#iommu-cells = <1>;
 			interrupt-parent = <&aic>;
 			interrupts = <AIC_IRQ 699 IRQ_TYPE_LEVEL_HIGH>;
+			power-domains = <&ps_apcie_gp>;
 		};
 
 		pcie0_dart_2: dart@683008000 {
@@ -242,6 +436,7 @@
 			#iommu-cells = <1>;
 			interrupt-parent = <&aic>;
 			interrupts = <AIC_IRQ 702 IRQ_TYPE_LEVEL_HIGH>;
+			power-domains = <&ps_apcie_gp>;
 		};
 
 		pcie0: pcie@690000000 {
@@ -276,6 +471,7 @@
 			ranges = <0x43000000 0x6 0xa0000000 0x6 0xa0000000 0x0 0x20000000>,
 				 <0x02000000 0x0 0xc0000000 0x6 0xc0000000 0x0 0x40000000>;
 
+			power-domains = <&ps_apcie_gp>;
 			pinctrl-0 = <&pcie_pins>;
 			pinctrl-names = "default";
 
@@ -283,7 +479,6 @@
 				device_type = "pci";
 				reg = <0x0 0x0 0x0 0x0 0x0>;
 				reset-gpios = <&pinctrl_ap 152 GPIO_ACTIVE_LOW>;
-				max-link-speed = <2>;
 
 				#address-cells = <3>;
 				#size-cells = <2>;
@@ -303,7 +498,6 @@
 				device_type = "pci";
 				reg = <0x800 0x0 0x0 0x0 0x0>;
 				reset-gpios = <&pinctrl_ap 153 GPIO_ACTIVE_LOW>;
-				max-link-speed = <2>;
 
 				#address-cells = <3>;
 				#size-cells = <2>;
@@ -323,7 +517,6 @@
 				device_type = "pci";
 				reg = <0x1000 0x0 0x0 0x0 0x0>;
 				reset-gpios = <&pinctrl_ap 33 GPIO_ACTIVE_LOW>;
-				max-link-speed = <1>;
 
 				#address-cells = <3>;
 				#size-cells = <2>;
@@ -341,3 +534,5 @@
 		};
 	};
 };
+
+#include "t8103-pmgr.dtsi"
diff --git a/arch/arm64/boot/dts/arm/Makefile b/arch/arm64/boot/dts/arm/Makefile
index 800da2e84f3f..d908e96d7ddc 100644
--- a/arch/arm64/boot/dts/arm/Makefile
+++ b/arch/arm64/boot/dts/arm/Makefile
@@ -2,7 +2,8 @@
 dtb-$(CONFIG_ARCH_VEXPRESS) += \
 	foundation-v8.dtb foundation-v8-psci.dtb \
 	foundation-v8-gicv3.dtb foundation-v8-gicv3-psci.dtb
-dtb-$(CONFIG_ARCH_VEXPRESS) += juno.dtb juno-r1.dtb juno-r2.dtb
+dtb-$(CONFIG_ARCH_VEXPRESS) += juno.dtb juno-r1.dtb juno-r2.dtb juno-scmi.dtb juno-r1-scmi.dtb juno-r2-scmi.dtb
 dtb-$(CONFIG_ARCH_VEXPRESS) += rtsm_ve-aemv8a.dtb
 dtb-$(CONFIG_ARCH_VEXPRESS) += vexpress-v2f-1xv7-ca53x2.dtb
 dtb-$(CONFIG_ARCH_VEXPRESS) += fvp-base-revc.dtb
+dtb-$(CONFIG_ARCH_VEXPRESS) += corstone1000-fvp.dtb corstone1000-mps3.dtb
diff --git a/arch/arm64/boot/dts/arm/corstone1000-fvp.dts b/arch/arm64/boot/dts/arm/corstone1000-fvp.dts
new file mode 100644
index 000000000000..26b0f1b3cea6
--- /dev/null
+++ b/arch/arm64/boot/dts/arm/corstone1000-fvp.dts
@@ -0,0 +1,51 @@
+// SPDX-License-Identifier: GPL-2.0 or MIT
+/*
+ * Copyright (c) 2022, Arm Limited. All rights reserved.
+ * Copyright (c) 2022, Linaro Limited. All rights reserved.
+ *
+ */
+
+/dts-v1/;
+
+#include "corstone1000.dtsi"
+
+/ {
+	model = "ARM Corstone1000 FVP (Fixed Virtual Platform)";
+	compatible = "arm,corstone1000-fvp";
+
+	smsc: ethernet@4010000 {
+		compatible = "smsc,lan91c111";
+		reg = <0x40100000 0x10000>;
+		phy-mode = "mii";
+		interrupts = <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>;
+		reg-io-width = <2>;
+	};
+
+	vmmc_v3_3d: fixed_v3_3d {
+		compatible = "regulator-fixed";
+		regulator-name = "vmmc_supply";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	sdmmc0: mmc@40300000 {
+		compatible = "arm,pl18x", "arm,primecell";
+		reg = <0x40300000 0x1000>;
+		interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
+		max-frequency = <12000000>;
+		vmmc-supply = <&vmmc_v3_3d>;
+		clocks = <&smbclk>, <&refclk100mhz>;
+		clock-names = "smclk", "apb_pclk";
+	};
+
+	sdmmc1: mmc@50000000 {
+		compatible = "arm,pl18x", "arm,primecell";
+		reg = <0x50000000 0x10000>;
+		interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>;
+		max-frequency = <12000000>;
+		vmmc-supply = <&vmmc_v3_3d>;
+		clocks = <&smbclk>, <&refclk100mhz>;
+		clock-names = "smclk", "apb_pclk";
+	};
+};
diff --git a/arch/arm64/boot/dts/arm/corstone1000-mps3.dts b/arch/arm64/boot/dts/arm/corstone1000-mps3.dts
new file mode 100644
index 000000000000..e3146747c2d9
--- /dev/null
+++ b/arch/arm64/boot/dts/arm/corstone1000-mps3.dts
@@ -0,0 +1,32 @@
+// SPDX-License-Identifier: GPL-2.0 or MIT
+/*
+ * Copyright (c) 2022, Arm Limited. All rights reserved.
+ * Copyright (c) 2022, Linaro Limited. All rights reserved.
+ *
+ */
+
+/dts-v1/;
+
+#include "corstone1000.dtsi"
+
+/ {
+	model = "ARM Corstone1000 FPGA MPS3 board";
+	compatible = "arm,corstone1000-mps3";
+
+	smsc: ethernet@4010000 {
+		compatible = "smsc,lan9220", "smsc,lan9115";
+		reg = <0x40100000 0x10000>;
+		phy-mode = "mii";
+		interrupts = <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>;
+		reg-io-width = <2>;
+		smsc,irq-push-pull;
+	};
+
+	usb_host: usb@40200000 {
+		compatible = "nxp,usb-isp1763";
+		reg = <0x40200000 0x100000>;
+		interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>;
+		bus-width = <16>;
+		dr_mode = "host";
+	};
+};
diff --git a/arch/arm64/boot/dts/arm/corstone1000.dtsi b/arch/arm64/boot/dts/arm/corstone1000.dtsi
new file mode 100644
index 000000000000..4e46826f883a
--- /dev/null
+++ b/arch/arm64/boot/dts/arm/corstone1000.dtsi
@@ -0,0 +1,164 @@
+// SPDX-License-Identifier: GPL-2.0 or MIT
+/*
+ * Copyright (c) 2022, Arm Limited. All rights reserved.
+ * Copyright (c) 2022, Linaro Limited. All rights reserved.
+ *
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+	interrupt-parent = <&gic>;
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	aliases {
+		serial0 = &uart0;
+		serial1 = &uart1;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a35";
+			reg = <0>;
+			next-level-cache = <&L2_0>;
+		};
+	};
+
+	memory@88200000 {
+		device_type = "memory";
+		reg = <0x88200000 0x77e00000>;
+	};
+
+	gic: interrupt-controller@1c000000 {
+		compatible = "arm,gic-400";
+		#interrupt-cells = <3>;
+		#address-cells = <0>;
+		interrupt-controller;
+		reg =	<0x1c010000 0x1000>,
+			<0x1c02f000 0x2000>,
+			<0x1c04f000 0x1000>,
+			<0x1c06f000 0x2000>;
+		interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(1) |
+			      IRQ_TYPE_LEVEL_LOW)>;
+	};
+
+	L2_0: l2-cache0 {
+		compatible = "cache";
+		cache-level = <2>;
+		cache-size = <0x80000>;
+		cache-line-size = <64>;
+		cache-sets = <1024>;
+	};
+
+	refclk100mhz: refclk100mhz {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <100000000>;
+		clock-output-names = "apb_pclk";
+	};
+
+	smbclk: refclk24mhzx2 {
+		/* Reference 24MHz clock x 2 */
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <48000000>;
+		clock-output-names = "smclk";
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupts =	<GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(1) |
+				 IRQ_TYPE_LEVEL_LOW)>,
+				<GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(1) |
+				 IRQ_TYPE_LEVEL_LOW)>,
+				<GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(1) |
+				 IRQ_TYPE_LEVEL_LOW)>,
+				<GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(1) |
+				 IRQ_TYPE_LEVEL_LOW)>;
+	};
+
+	uartclk: uartclk {
+		/* UART clock - 50MHz */
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <50000000>;
+		clock-output-names = "uartclk";
+	};
+
+	psci {
+		compatible = "arm,psci-1.0", "arm,psci-0.2";
+		method = "smc";
+	};
+
+	soc {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		interrupt-parent = <&gic>;
+		ranges;
+
+		timer@1a220000 {
+			compatible = "arm,armv7-timer-mem";
+			reg = <0x1a220000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			clock-frequency = <50000000>;
+			ranges;
+
+			frame@1a230000 {
+				frame-number = <0>;
+				interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x1a230000 0x1000>;
+			};
+		};
+
+		uart0: serial@1a510000 {
+			compatible = "arm,pl011", "arm,primecell";
+			reg = <0x1a510000 0x1000>;
+			interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&uartclk>, <&refclk100mhz>;
+			clock-names = "uartclk", "apb_pclk";
+		};
+
+		uart1: serial@1a520000 {
+			compatible = "arm,pl011", "arm,primecell";
+			reg = <0x1a520000 0x1000>;
+			interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&uartclk>, <&refclk100mhz>;
+			clock-names = "uartclk", "apb_pclk";
+		};
+
+		mhu_hse1: mailbox@1b820000 {
+			compatible = "arm,mhuv2-tx", "arm,primecell";
+			reg = <0x1b820000 0x1000>;
+			clocks = <&refclk100mhz>;
+			clock-names = "apb_pclk";
+			interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
+			#mbox-cells = <2>;
+			arm,mhuv2-protocols = <0 0>;
+			secure-status = "okay";     /* secure-world-only */
+			status = "disabled";
+		};
+
+		mhu_seh1: mailbox@1b830000 {
+			compatible = "arm,mhuv2-rx", "arm,primecell";
+			reg = <0x1b830000 0x1000>;
+			clocks = <&refclk100mhz>;
+			clock-names = "apb_pclk";
+			interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
+			#mbox-cells = <2>;
+			arm,mhuv2-protocols = <0 0>;
+			secure-status = "okay";     /* secure-world-only */
+			status = "disabled";
+		};
+	};
+};
diff --git a/arch/arm64/boot/dts/arm/foundation-v8.dtsi b/arch/arm64/boot/dts/arm/foundation-v8.dtsi
index fbf13f7c2baf..83e3e7e3984f 100644
--- a/arch/arm64/boot/dts/arm/foundation-v8.dtsi
+++ b/arch/arm64/boot/dts/arm/foundation-v8.dtsi
@@ -220,7 +220,7 @@
 				clock-names = "uartclk", "apb_pclk";
 			};
 
-			virtio-block@130000 {
+			virtio@130000 {
 				compatible = "virtio,mmio";
 				reg = <0x130000 0x200>;
 				interrupts = <42>;
diff --git a/arch/arm64/boot/dts/arm/fvp-base-revc.dts b/arch/arm64/boot/dts/arm/fvp-base-revc.dts
index 269b649934b5..5f6f30c801a7 100644
--- a/arch/arm64/boot/dts/arm/fvp-base-revc.dts
+++ b/arch/arm64/boot/dts/arm/fvp-base-revc.dts
@@ -186,7 +186,7 @@
 	};
 
 	panel {
-		compatible = "arm,rtsm-display", "panel-dpi";
+		compatible = "arm,rtsm-display";
 		port {
 			panel_in: endpoint {
 				remote-endpoint = <&clcd_pads>;
@@ -241,6 +241,7 @@
 				<0 0 41 &gic 0 0 GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>,
 				<0 0 42 &gic 0 0 GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>,
 				<0 0 43 &gic 0 0 GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>,
-				<0 0 44 &gic 0 0 GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
+				<0 0 44 &gic 0 0 GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>,
+				<0 0 46 &gic 0 0 GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
 	};
 };
diff --git a/arch/arm64/boot/dts/arm/juno-base.dtsi b/arch/arm64/boot/dts/arm/juno-base.dtsi
index 6288e104a089..8b4d280b1e7e 100644
--- a/arch/arm64/boot/dts/arm/juno-base.dtsi
+++ b/arch/arm64/boot/dts/arm/juno-base.dtsi
@@ -26,7 +26,8 @@
 		compatible = "arm,mhu", "arm,primecell";
 		reg = <0x0 0x2b1f0000 0x0 0x1000>;
 		interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>,
-			     <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
+			     <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
 		#mbox-cells = <1>;
 		clocks = <&soc_refclk100mhz>;
 		clock-names = "apb_pclk";
@@ -117,7 +118,7 @@
 	 * The actual size is just 4K though 64K is reserved. Access to the
 	 * unmapped reserved region results in a DECERR response.
 	 */
-	etf@20010000 { /* etf0 */
+	etf_sys0: etf@20010000 { /* etf0 */
 		compatible = "arm,coresight-tmc", "arm,primecell";
 		reg = <0 0x20010000 0 0x1000>;
 
@@ -141,7 +142,7 @@
 		};
 	};
 
-	tpiu@20030000 {
+	tpiu_sys: tpiu@20030000 {
 		compatible = "arm,coresight-tpiu", "arm,primecell";
 		reg = <0 0x20030000 0 0x1000>;
 
@@ -194,7 +195,7 @@
 		};
 	};
 
-	etr@20070000 {
+	etr_sys: etr@20070000 {
 		compatible = "arm,coresight-tmc", "arm,primecell";
 		reg = <0 0x20070000 0 0x1000>;
 		iommus = <&smmu_etr 0>;
@@ -212,7 +213,7 @@
 		};
 	};
 
-	stm@20100000 {
+	stm_sys: stm@20100000 {
 		compatible = "arm,coresight-stm", "arm,primecell";
 		reg = <0 0x20100000 0 0x1000>,
 		      <0 0x28000000 0 0x1000000>;
@@ -289,6 +290,18 @@
 		};
 	};
 
+	cti0: cti@22020000 {
+		compatible = "arm,coresight-cti-v8-arch", "arm,coresight-cti",
+			     "arm,primecell";
+		reg = <0 0x22020000 0 0x1000>;
+
+		clocks = <&soc_smc50mhz>;
+		clock-names = "apb_pclk";
+		power-domains = <&scpi_devpd 0>;
+
+		arm,cs-dev-assoc = <&etm0>;
+	};
+
 	funnel@220c0000 { /* cluster0 funnel */
 		compatible = "arm,coresight-dynamic-funnel", "arm,primecell";
 		reg = <0 0x220c0000 0 0x1000>;
@@ -349,6 +362,18 @@
 		};
 	};
 
+	cti1: cti@22120000 {
+		compatible = "arm,coresight-cti-v8-arch", "arm,coresight-cti",
+			     "arm,primecell";
+		reg = <0 0x22120000 0 0x1000>;
+
+		clocks = <&soc_smc50mhz>;
+		clock-names = "apb_pclk";
+		power-domains = <&scpi_devpd 0>;
+
+		arm,cs-dev-assoc = <&etm1>;
+	};
+
 	cpu_debug2: cpu-debug@23010000 {
 		compatible = "arm,coresight-cpu-debug", "arm,primecell";
 		reg = <0x0 0x23010000 0x0 0x1000>;
@@ -374,6 +399,18 @@
 		};
 	};
 
+	cti2: cti@23020000 {
+		compatible = "arm,coresight-cti-v8-arch", "arm,coresight-cti",
+			     "arm,primecell";
+		reg = <0 0x23020000 0 0x1000>;
+
+		clocks = <&soc_smc50mhz>;
+		clock-names = "apb_pclk";
+		power-domains = <&scpi_devpd 0>;
+
+		arm,cs-dev-assoc = <&etm2>;
+	};
+
 	funnel@230c0000 { /* cluster1 funnel */
 		compatible = "arm,coresight-dynamic-funnel", "arm,primecell";
 		reg = <0 0x230c0000 0 0x1000>;
@@ -446,6 +483,18 @@
 		};
 	};
 
+	cti3: cti@23120000 {
+		compatible = "arm,coresight-cti-v8-arch", "arm,coresight-cti",
+			     "arm,primecell";
+		reg = <0 0x23120000 0 0x1000>;
+
+		clocks = <&soc_smc50mhz>;
+		clock-names = "apb_pclk";
+		power-domains = <&scpi_devpd 0>;
+
+		arm,cs-dev-assoc = <&etm3>;
+	};
+
 	cpu_debug4: cpu-debug@23210000 {
 		compatible = "arm,coresight-cpu-debug", "arm,primecell";
 		reg = <0x0 0x23210000 0x0 0x1000>;
@@ -471,6 +520,18 @@
 		};
 	};
 
+	cti4: cti@23220000 {
+		compatible = "arm,coresight-cti-v8-arch", "arm,coresight-cti",
+			     "arm,primecell";
+		reg = <0 0x23220000 0 0x1000>;
+
+		clocks = <&soc_smc50mhz>;
+		clock-names = "apb_pclk";
+		power-domains = <&scpi_devpd 0>;
+
+		arm,cs-dev-assoc = <&etm4>;
+	};
+
 	cpu_debug5: cpu-debug@23310000 {
 		compatible = "arm,coresight-cpu-debug", "arm,primecell";
 		reg = <0x0 0x23310000 0x0 0x1000>;
@@ -496,6 +557,100 @@
 		};
 	};
 
+	cti5: cti@23320000 {
+		compatible = "arm,coresight-cti-v8-arch", "arm,coresight-cti",
+			     "arm,primecell";
+		reg = <0 0x23320000 0 0x1000>;
+
+		clocks = <&soc_smc50mhz>;
+		clock-names = "apb_pclk";
+		power-domains = <&scpi_devpd 0>;
+
+		arm,cs-dev-assoc = <&etm5>;
+	};
+
+	cti_sys0: cti@20020000 { /* sys_cti_0 */
+		compatible = "arm,coresight-cti", "arm,primecell";
+		reg = <0 0x20020000 0 0x1000>;
+
+		clocks = <&soc_smc50mhz>;
+		clock-names = "apb_pclk";
+		power-domains = <&scpi_devpd 0>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		trig-conns@0 {
+			reg = <0>;
+			arm,trig-in-sigs = <2 3>;
+			arm,trig-in-types = <SNK_FULL SNK_ACQCOMP>;
+			arm,trig-out-sigs = <0 1>;
+			arm,trig-out-types = <SNK_FLUSHIN SNK_TRIGIN>;
+			arm,cs-dev-assoc = <&etr_sys>;
+		};
+
+		trig-conns@1 {
+			reg = <1>;
+			arm,trig-in-sigs = <0 1>;
+			arm,trig-in-types = <SNK_FULL SNK_ACQCOMP>;
+			arm,trig-out-sigs = <7 6>;
+			arm,trig-out-types = <SNK_FLUSHIN SNK_TRIGIN>;
+			arm,cs-dev-assoc = <&etf_sys0>;
+		};
+
+		trig-conns@2 {
+			reg = <2>;
+			arm,trig-in-sigs = <4 5 6 7>;
+			arm,trig-in-types = <STM_TOUT_SPTE STM_TOUT_SW
+					   STM_TOUT_HETE STM_ASYNCOUT>;
+			arm,trig-out-sigs = <4 5>;
+			arm,trig-out-types = <STM_HWEVENT STM_HWEVENT>;
+			arm,cs-dev-assoc = <&stm_sys>;
+		};
+
+		trig-conns@3 {
+			reg = <3>;
+			arm,trig-out-sigs = <2 3>;
+			arm,trig-out-types = <SNK_FLUSHIN SNK_TRIGIN>;
+			arm,cs-dev-assoc = <&tpiu_sys>;
+		};
+	};
+
+	cti_sys1: cti@20110000 { /* sys_cti_1 */
+		compatible = "arm,coresight-cti", "arm,primecell";
+		reg = <0 0x20110000 0 0x1000>;
+
+		clocks = <&soc_smc50mhz>;
+		clock-names = "apb_pclk";
+		power-domains = <&scpi_devpd 0>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		trig-conns@0 {
+			reg = <0>;
+			arm,trig-in-sigs = <0>;
+			arm,trig-in-types = <GEN_INTREQ>;
+			arm,trig-out-sigs = <0>;
+			arm,trig-out-types = <GEN_HALTREQ>;
+			arm,trig-conn-name = "sys_profiler";
+		};
+
+		trig-conns@1 {
+			reg = <1>;
+			arm,trig-out-sigs = <2 3>;
+			arm,trig-out-types = <GEN_HALTREQ GEN_RESTARTREQ>;
+			arm,trig-conn-name = "watchdog";
+		};
+
+		trig-conns@2 {
+			reg = <2>;
+			arm,trig-out-sigs = <1 6>;
+			arm,trig-out-types = <GEN_HALTREQ GEN_RESTARTREQ>;
+			arm,trig-conn-name = "g_counter";
+		};
+	};
+
 	gpu: gpu@2d000000 {
 		compatible = "arm,juno-mali", "arm,mali-t624";
 		reg = <0 0x2d000000 0 0x10000>;
@@ -543,8 +698,7 @@
 			 <0x02000000 0x00 0x50000000 0x00 0x50000000 0x0 0x08000000>,
 			 <0x42000000 0x40 0x00000000 0x40 0x00000000 0x1 0x00000000>;
 		/* Standard AXI Translation entries as programmed by EDK2 */
-		dma-ranges = <0x02000000 0x0 0x2c1c0000 0x0 0x2c1c0000 0x0 0x00040000>,
-			     <0x02000000 0x0 0x80000000 0x0 0x80000000 0x0 0x80000000>,
+		dma-ranges = <0x02000000 0x0 0x80000000 0x0 0x80000000 0x0 0x80000000>,
 			     <0x43000000 0x8 0x00000000 0x8 0x00000000 0x2 0x00000000>;
 		#interrupt-cells = <1>;
 		interrupt-map-mask = <0 0 0 7>;
@@ -597,12 +751,26 @@
 			polling-delay = <1000>;
 			polling-delay-passive = <100>;
 			thermal-sensors = <&scpi_sensors0 0>;
+			trips {
+				pmic_crit0: trip0 {
+					temperature = <90000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
 		};
 
 		soc {
 			polling-delay = <1000>;
 			polling-delay-passive = <100>;
 			thermal-sensors = <&scpi_sensors0 3>;
+			trips {
+				soc_crit0: trip0 {
+					temperature = <80000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
 		};
 
 		big_cluster_thermal_zone: big-cluster {
@@ -672,12 +840,10 @@
 		dma-coherent;
 	};
 
-	dma@7ff00000 {
+	dma-controller@7ff00000 {
 		compatible = "arm,pl330", "arm,primecell";
 		reg = <0x0 0x7ff00000 0 0x1000>;
 		#dma-cells = <1>;
-		#dma-channels = <8>;
-		#dma-requests = <32>;
 		interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>,
 			     <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>,
 			     <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>,
diff --git a/arch/arm64/boot/dts/arm/juno-cs-r1r2.dtsi b/arch/arm64/boot/dts/arm/juno-cs-r1r2.dtsi
index eda3d9e18af6..09d2b692e9e1 100644
--- a/arch/arm64/boot/dts/arm/juno-cs-r1r2.dtsi
+++ b/arch/arm64/boot/dts/arm/juno-cs-r1r2.dtsi
@@ -23,7 +23,7 @@
 		};
 	};
 
-	etf@20140000 { /* etf1 */
+	etf_sys1: etf@20140000 { /* etf1 */
 		compatible = "arm,coresight-tmc", "arm,primecell";
 		reg = <0 0x20140000 0 0x1000>;
 
@@ -67,7 +67,6 @@
 			port@0 {
 				reg = <0>;
 				csys2_funnel_in_port0: endpoint {
-					slave-mode;
 					remote-endpoint = <&etf0_out_port>;
 				};
 			};
@@ -75,11 +74,45 @@
 			port@1 {
 				reg = <1>;
 				csys2_funnel_in_port1: endpoint {
-					slave-mode;
 					remote-endpoint = <&etf1_out_port>;
 				};
 			};
 
 		};
 	};
+
+	cti_sys2: cti@20160000 { /* sys_cti_2 */
+		compatible = "arm,coresight-cti", "arm,primecell";
+		reg = <0 0x20160000 0 0x1000>;
+
+		clocks = <&soc_smc50mhz>;
+		clock-names = "apb_pclk";
+		power-domains = <&scpi_devpd 0>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		trig-conns@0 {
+			reg = <0>;
+			arm,trig-in-sigs = <0 1>;
+			arm,trig-in-types = <SNK_FULL SNK_ACQCOMP>;
+			arm,trig-out-sigs = <0 1>;
+			arm,trig-out-types = <SNK_FLUSHIN SNK_TRIGIN>;
+			arm,cs-dev-assoc = <&etf_sys1>;
+		};
+
+		trig-conns@1 {
+			reg = <1>;
+			arm,trig-in-sigs = <2 3 4>;
+			arm,trig-in-types = <ELA_DBGREQ ELA_TSTART ELA_TSTOP>;
+			arm,trig-conn-name = "ela_clus_0";
+		};
+
+		trig-conns@2 {
+			reg = <2>;
+			arm,trig-in-sigs = <5 6 7>;
+			arm,trig-in-types = <ELA_DBGREQ ELA_TSTART ELA_TSTOP>;
+			arm,trig-conn-name = "ela_clus_1";
+		};
+	};
 };
diff --git a/arch/arm64/boot/dts/arm/juno-r1-scmi.dts b/arch/arm64/boot/dts/arm/juno-r1-scmi.dts
new file mode 100644
index 000000000000..dd9ea69f086f
--- /dev/null
+++ b/arch/arm64/boot/dts/arm/juno-r1-scmi.dts
@@ -0,0 +1,27 @@
+#include "juno-r1.dts"
+#include "juno-scmi.dtsi"
+
+/ {
+	funnel@20130000 {
+		power-domains = <&scmi_devpd 8>;
+	};
+
+	etf@20140000 {
+		power-domains = <&scmi_devpd 8>;
+	};
+
+	funnel@20150000 {
+		power-domains = <&scmi_devpd 8>;
+	};
+};
+
+&cti_sys2 {
+	power-domains = <&scmi_devpd 8>;
+};
+
+&A57_0 {
+	clocks = <&scmi_dvfs 0>;
+};
+&A57_1 {
+	clocks = <&scmi_dvfs 0>;
+};
diff --git a/arch/arm64/boot/dts/arm/juno-r1.dts b/arch/arm64/boot/dts/arm/juno-r1.dts
index 0e24e29eb9b1..6451c62146fd 100644
--- a/arch/arm64/boot/dts/arm/juno-r1.dts
+++ b/arch/arm64/boot/dts/arm/juno-r1.dts
@@ -9,6 +9,7 @@
 /dts-v1/;
 
 #include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/arm/coresight-cti-dt.h>
 #include "juno-base.dtsi"
 #include "juno-cs-r1r2.dtsi"
 
@@ -191,6 +192,7 @@
 			cache-size = <0x200000>;
 			cache-line-size = <64>;
 			cache-sets = <2048>;
+			cache-level = <2>;
 		};
 
 		A53_L2: l2-cache1 {
@@ -198,6 +200,7 @@
 			cache-size = <0x100000>;
 			cache-line-size = <64>;
 			cache-sets = <1024>;
+			cache-level = <2>;
 		};
 	};
 
@@ -313,3 +316,27 @@
 &cpu_debug5 {
 	cpu = <&A53_3>;
 };
+
+&cti0 {
+	cpu = <&A57_0>;
+};
+
+&cti1 {
+	cpu = <&A57_1>;
+};
+
+&cti2 {
+	cpu = <&A53_0>;
+};
+
+&cti3 {
+	cpu = <&A53_1>;
+};
+
+&cti4 {
+	cpu = <&A53_2>;
+};
+
+&cti5 {
+	cpu = <&A53_3>;
+};
diff --git a/arch/arm64/boot/dts/arm/juno-r2-scmi.dts b/arch/arm64/boot/dts/arm/juno-r2-scmi.dts
new file mode 100644
index 000000000000..de2cbac1d1c3
--- /dev/null
+++ b/arch/arm64/boot/dts/arm/juno-r2-scmi.dts
@@ -0,0 +1,27 @@
+#include "juno-r2.dts"
+#include "juno-scmi.dtsi"
+
+/ {
+	funnel@20130000 {
+		power-domains = <&scmi_devpd 8>;
+	};
+
+	etf@20140000 {
+		power-domains = <&scmi_devpd 8>;
+	};
+
+	funnel@20150000 {
+		power-domains = <&scmi_devpd 8>;
+	};
+};
+
+&cti_sys2 {
+	power-domains = <&scmi_devpd 8>;
+};
+
+&A72_0 {
+	clocks = <&scmi_dvfs 0>;
+};
+&A72_1 {
+	clocks = <&scmi_dvfs 0>;
+};
diff --git a/arch/arm64/boot/dts/arm/juno-r2.dts b/arch/arm64/boot/dts/arm/juno-r2.dts
index e609420ce3e4..438cd1ff4bd0 100644
--- a/arch/arm64/boot/dts/arm/juno-r2.dts
+++ b/arch/arm64/boot/dts/arm/juno-r2.dts
@@ -9,6 +9,7 @@
 /dts-v1/;
 
 #include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/arm/coresight-cti-dt.h>
 #include "juno-base.dtsi"
 #include "juno-cs-r1r2.dtsi"
 
@@ -197,6 +198,7 @@
 			cache-size = <0x200000>;
 			cache-line-size = <64>;
 			cache-sets = <2048>;
+			cache-level = <2>;
 		};
 
 		A53_L2: l2-cache1 {
@@ -204,6 +206,7 @@
 			cache-size = <0x100000>;
 			cache-line-size = <64>;
 			cache-sets = <1024>;
+			cache-level = <2>;
 		};
 	};
 
@@ -319,3 +322,27 @@
 &cpu_debug5 {
 	cpu = <&A53_3>;
 };
+
+&cti0 {
+	cpu = <&A72_0>;
+};
+
+&cti1 {
+	cpu = <&A72_1>;
+};
+
+&cti2 {
+	cpu = <&A53_0>;
+};
+
+&cti3 {
+	cpu = <&A53_1>;
+};
+
+&cti4 {
+	cpu = <&A53_2>;
+};
+
+&cti5 {
+	cpu = <&A53_3>;
+};
diff --git a/arch/arm64/boot/dts/arm/juno-scmi.dts b/arch/arm64/boot/dts/arm/juno-scmi.dts
new file mode 100644
index 000000000000..41588fa46d31
--- /dev/null
+++ b/arch/arm64/boot/dts/arm/juno-scmi.dts
@@ -0,0 +1,9 @@
+#include "juno.dts"
+#include "juno-scmi.dtsi"
+
+&A57_0 {
+	clocks = <&scmi_dvfs 0>;
+};
+&A57_1 {
+	clocks = <&scmi_dvfs 0>;
+};
diff --git a/arch/arm64/boot/dts/arm/juno-scmi.dtsi b/arch/arm64/boot/dts/arm/juno-scmi.dtsi
new file mode 100644
index 000000000000..ec85cd2c733c
--- /dev/null
+++ b/arch/arm64/boot/dts/arm/juno-scmi.dtsi
@@ -0,0 +1,223 @@
+/ {
+	etf@20010000 {
+		power-domains = <&scmi_devpd 8>;
+	};
+
+	tpiu@20030000 {
+		power-domains = <&scmi_devpd 8>;
+	};
+
+	funnel@20040000 {
+		power-domains = <&scmi_devpd 8>;
+	};
+
+	etr@20070000 {
+		power-domains = <&scmi_devpd 8>;
+	};
+
+	stm@20100000 {
+		power-domains = <&scmi_devpd 8>;
+	};
+
+	replicator@20120000 {
+		power-domains = <&scmi_devpd 8>;
+	};
+
+	funnel@220c0000 {
+		power-domains = <&scmi_devpd 8>;
+	};
+
+	funnel@230c0000 {
+		power-domains = <&scmi_devpd 8>;
+	};
+
+	hdlcd@7ff50000 {
+		clocks = <&scmi_clk 3>;
+	};
+
+	hdlcd@7ff60000 {
+		clocks = <&scmi_clk 3>;
+	};
+
+	/delete-node/ scpi;
+
+	firmware {
+		scmi {
+			compatible = "arm,scmi";
+			mbox-names = "tx", "rx";
+			mboxes = <&mailbox 0 0 &mailbox 0 1>;
+			shmem = <&cpu_scp_lpri0 &cpu_scp_lpri1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			scmi_devpd: protocol@11 {
+				reg = <0x11>;
+				#power-domain-cells = <1>;
+			};
+
+			scmi_dvfs: protocol@13 {
+				reg = <0x13>;
+				#clock-cells = <1>;
+				mbox-names = "tx", "rx";
+				mboxes = <&mailbox 1 0 &mailbox 1 1>;
+				shmem = <&cpu_scp_hpri0 &cpu_scp_hpri1>;
+			};
+
+			scmi_clk: protocol@14 {
+				reg = <0x14>;
+				#clock-cells = <1>;
+			};
+
+			scmi_sensors0: protocol@15 {
+				reg = <0x15>;
+				#thermal-sensor-cells = <1>;
+			};
+		};
+	};
+
+	thermal-zones {
+		pmic {
+			thermal-sensors = <&scmi_sensors0 0>;
+		};
+
+		soc {
+			thermal-sensors = <&scmi_sensors0 3>;
+		};
+
+		big-cluster {
+			thermal-sensors = <&scmi_sensors0 21>;
+		};
+
+		little-cluster {
+			thermal-sensors = <&scmi_sensors0 22>;
+		};
+
+		gpu0 {
+			thermal-sensors = <&scmi_sensors0 23>;
+		};
+
+		gpu1 {
+			thermal-sensors = <&scmi_sensors0 24>;
+		};
+	};
+
+};
+
+&A53_0 {
+	clocks = <&scmi_dvfs 1>;
+};
+&A53_1 {
+	clocks = <&scmi_dvfs 1>;
+};
+&A53_2 {
+	clocks = <&scmi_dvfs 1>;
+};
+&A53_3 {
+	clocks = <&scmi_dvfs 1>;
+};
+
+&cpu_debug0 {
+	power-domains = <&scmi_devpd 8>;
+};
+&cpu_debug1 {
+	power-domains = <&scmi_devpd 8>;
+};
+&cpu_debug2 {
+	power-domains = <&scmi_devpd 8>;
+};
+&cpu_debug3 {
+	power-domains = <&scmi_devpd 8>;
+};
+&cpu_debug4 {
+	power-domains = <&scmi_devpd 8>;
+};
+&cpu_debug5 {
+	power-domains = <&scmi_devpd 8>;
+};
+
+&etm0 {
+	power-domains = <&scmi_devpd 8>;
+};
+&etm1 {
+	power-domains = <&scmi_devpd 8>;
+};
+&etm2 {
+	power-domains = <&scmi_devpd 8>;
+};
+&etm3 {
+	power-domains = <&scmi_devpd 8>;
+};
+&etm4 {
+	power-domains = <&scmi_devpd 8>;
+};
+&etm5 {
+	power-domains = <&scmi_devpd 8>;
+};
+
+&cti0 {
+	power-domains = <&scmi_devpd 8>;
+};
+&cti1 {
+	power-domains = <&scmi_devpd 8>;
+};
+&cti2 {
+	power-domains = <&scmi_devpd 8>;
+};
+&cti3 {
+	power-domains = <&scmi_devpd 8>;
+};
+&cti4 {
+	power-domains = <&scmi_devpd 8>;
+};
+&cti5 {
+	power-domains = <&scmi_devpd 8>;
+};
+&cti_sys0 {
+	power-domains = <&scmi_devpd 8>;
+};
+&cti_sys1 {
+	power-domains = <&scmi_devpd 8>;
+};
+
+&gpu {
+	clocks = <&scmi_dvfs 2>;
+	power-domains = <&scmi_devpd 9>;
+};
+
+&mailbox {
+	compatible = "arm,mhu-doorbell", "arm,primecell";
+	#mbox-cells = <2>;
+};
+
+&smmu_etr {
+	power-domains = <&scmi_devpd 8>;
+};
+
+&smmu_gpu {
+	power-domains = <&scmi_devpd 9>;
+};
+
+&sram {
+	/delete-node/ scp-sram@0;
+	/delete-node/ scp-sram@200;
+
+	cpu_scp_lpri0: scp-sram@0 {
+		compatible = "arm,scmi-shmem";
+		reg = <0x0 0x80>;
+	};
+
+	cpu_scp_lpri1: scp-sram@80 {
+		compatible = "arm,scmi-shmem";
+		reg = <0x80 0x80>;
+	};
+
+	cpu_scp_hpri0: scp-sram@100 {
+		compatible = "arm,scmi-shmem";
+		reg = <0x100 0x80>;
+	};
+
+	cpu_scp_hpri1: scp-sram@180 {
+		compatible = "arm,scmi-shmem";
+		reg = <0x180 0x80>;
+	};
+};
diff --git a/arch/arm64/boot/dts/arm/juno.dts b/arch/arm64/boot/dts/arm/juno.dts
index f00cffbd032c..cf4a58211399 100644
--- a/arch/arm64/boot/dts/arm/juno.dts
+++ b/arch/arm64/boot/dts/arm/juno.dts
@@ -9,6 +9,7 @@
 /dts-v1/;
 
 #include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/arm/coresight-cti-dt.h>
 #include "juno-base.dtsi"
 
 / {
@@ -196,6 +197,7 @@
 			cache-size = <0x200000>;
 			cache-line-size = <64>;
 			cache-sets = <2048>;
+			cache-level = <2>;
 		};
 
 		A53_L2: l2-cache1 {
@@ -203,6 +205,7 @@
 			cache-size = <0x100000>;
 			cache-line-size = <64>;
 			cache-sets = <1024>;
+			cache-level = <2>;
 		};
 	};
 
@@ -295,3 +298,27 @@
 &cpu_debug5 {
 	cpu = <&A53_3>;
 };
+
+&cti0 {
+	cpu = <&A57_0>;
+};
+
+&cti1 {
+	cpu = <&A57_1>;
+};
+
+&cti2 {
+	cpu = <&A53_0>;
+};
+
+&cti3 {
+	cpu = <&A53_1>;
+};
+
+&cti4 {
+	cpu = <&A53_2>;
+};
+
+&cti5 {
+	cpu = <&A53_3>;
+};
diff --git a/arch/arm64/boot/dts/arm/rtsm_ve-motherboard-rs2.dtsi b/arch/arm64/boot/dts/arm/rtsm_ve-motherboard-rs2.dtsi
index 33182d9e5826..ec2d5280a30b 100644
--- a/arch/arm64/boot/dts/arm/rtsm_ve-motherboard-rs2.dtsi
+++ b/arch/arm64/boot/dts/arm/rtsm_ve-motherboard-rs2.dtsi
@@ -10,17 +10,24 @@
 			arm,v2m-memory-map = "rs2";
 
 			iofpga-bus@300000000 {
-				virtio-p9@140000 {
+				virtio@140000 {
 					compatible = "virtio,mmio";
 					reg = <0x140000 0x200>;
 					interrupts = <43>;
 				};
 
-				virtio-net@150000 {
+				virtio@150000 {
 					compatible = "virtio,mmio";
 					reg = <0x150000 0x200>;
 					interrupts = <44>;
 				};
+
+				virtio@200000 {
+					compatible = "virtio,mmio";
+					reg = <0x200000 0x200>;
+					interrupts = <46>;
+					status = "disabled";
+				};
 			};
 		};
 	};
diff --git a/arch/arm64/boot/dts/arm/rtsm_ve-motherboard.dtsi b/arch/arm64/boot/dts/arm/rtsm_ve-motherboard.dtsi
index 5f6cab668aa0..ba8beef3fe99 100644
--- a/arch/arm64/boot/dts/arm/rtsm_ve-motherboard.dtsi
+++ b/arch/arm64/boot/dts/arm/rtsm_ve-motherboard.dtsi
@@ -110,7 +110,7 @@
 				compatible = "simple-bus";
 				#address-cells = <1>;
 				#size-cells = <1>;
-				ranges = <0 3 0 0x200000>;
+				ranges = <0 3 0 0x210000>;
 
 				v2m_sysreg: sysreg@10000 {
 					compatible = "arm,vexpress-sysreg";
@@ -222,7 +222,7 @@
 					clock-names = "timclken1", "timclken2", "apb_pclk";
 				};
 
-				virtio-block@130000 {
+				virtio@130000 {
 					compatible = "virtio,mmio";
 					reg = <0x130000 0x200>;
 					interrupts = <42>;
diff --git a/arch/arm64/boot/dts/broadcom/Makefile b/arch/arm64/boot/dts/broadcom/Makefile
index c6882032a428..05d8c5ecf3b0 100644
--- a/arch/arm64/boot/dts/broadcom/Makefile
+++ b/arch/arm64/boot/dts/broadcom/Makefile
@@ -5,8 +5,9 @@ dtb-$(CONFIG_ARCH_BCM2835) += bcm2711-rpi-400.dtb \
 			      bcm2837-rpi-3-a-plus.dtb \
 			      bcm2837-rpi-3-b.dtb \
 			      bcm2837-rpi-3-b-plus.dtb \
-			      bcm2837-rpi-cm3-io3.dtb
+			      bcm2837-rpi-cm3-io3.dtb \
+			      bcm2837-rpi-zero-2-w.dtb
 
-subdir-y	+= bcm4908
+subdir-y	+= bcmbca
 subdir-y	+= northstar2
 subdir-y	+= stingray
diff --git a/arch/arm64/boot/dts/broadcom/bcm2837-rpi-zero-2-w.dts b/arch/arm64/boot/dts/broadcom/bcm2837-rpi-zero-2-w.dts
new file mode 100644
index 000000000000..307ae693e4a0
--- /dev/null
+++ b/arch/arm64/boot/dts/broadcom/bcm2837-rpi-zero-2-w.dts
@@ -0,0 +1,2 @@
+// SPDX-License-Identifier: GPL-2.0
+#include "arm/bcm2837-rpi-zero-2-w.dts"
diff --git a/arch/arm64/boot/dts/broadcom/bcm4908/Makefile b/arch/arm64/boot/dts/broadcom/bcm4908/Makefile
deleted file mode 100644
index cc75854519ac..000000000000
--- a/arch/arm64/boot/dts/broadcom/bcm4908/Makefile
+++ /dev/null
@@ -1,4 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0
-dtb-$(CONFIG_ARCH_BCM4908) += bcm4906-netgear-r8000p.dtb
-dtb-$(CONFIG_ARCH_BCM4908) += bcm4906-tplink-archer-c2300-v1.dtb
-dtb-$(CONFIG_ARCH_BCM4908) += bcm4908-asus-gt-ac5300.dtb
diff --git a/arch/arm64/boot/dts/broadcom/bcm4908/bcm4906.dtsi b/arch/arm64/boot/dts/broadcom/bcm4908/bcm4906.dtsi
deleted file mode 100644
index 66023d553524..000000000000
--- a/arch/arm64/boot/dts/broadcom/bcm4908/bcm4906.dtsi
+++ /dev/null
@@ -1,18 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
-
-#include "bcm4908.dtsi"
-
-/ {
-	cpus {
-		/delete-node/ cpu@2;
-
-		/delete-node/ cpu@3;
-	};
-
-	pmu {
-		compatible = "arm,cortex-a53-pmu";
-		interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
-			     <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
-		interrupt-affinity = <&cpu0>, <&cpu1>;
-	};
-};
diff --git a/arch/arm64/boot/dts/broadcom/bcm4908/bcm4908-asus-gt-ac5300.dts b/arch/arm64/boot/dts/broadcom/bcm4908/bcm4908-asus-gt-ac5300.dts
deleted file mode 100644
index 169fbb7cfd34..000000000000
--- a/arch/arm64/boot/dts/broadcom/bcm4908/bcm4908-asus-gt-ac5300.dts
+++ /dev/null
@@ -1,159 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
-
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-
-#include "bcm4908.dtsi"
-
-/ {
-	compatible = "asus,gt-ac5300", "brcm,bcm4908";
-	model = "Asus GT-AC5300";
-
-	memory@0 {
-		device_type = "memory";
-		reg = <0x00 0x00 0x00 0x40000000>;
-	};
-
-	gpio-keys-polled {
-		compatible = "gpio-keys-polled";
-		poll-interval = <100>;
-
-		wifi {
-			label = "WiFi";
-			linux,code = <KEY_RFKILL>;
-			gpios = <&gpio0 28 GPIO_ACTIVE_LOW>;
-		};
-
-		wps {
-			label = "WPS";
-			linux,code = <KEY_WPS_BUTTON>;
-			gpios = <&gpio0 29 GPIO_ACTIVE_LOW>;
-		};
-
-		restart {
-			label = "Reset";
-			linux,code = <KEY_RESTART>;
-			gpios = <&gpio0 30 GPIO_ACTIVE_LOW>;
-		};
-
-		brightness {
-			label = "LEDs";
-			linux,code = <KEY_BRIGHTNESS_ZERO>;
-			gpios = <&gpio0 31 GPIO_ACTIVE_LOW>;
-		};
-	};
-};
-
-&enet {
-	nvmem-cells = <&base_mac_addr>;
-	nvmem-cell-names = "mac-address";
-};
-
-&usb_phy {
-	brcm,ioc = <1>;
-	status = "okay";
-};
-
-&ehci {
-	status = "okay";
-};
-
-&ohci {
-	status = "okay";
-};
-
-&xhci {
-	status = "okay";
-};
-
-&ports {
-	port@0 {
-		label = "lan2";
-	};
-
-	port@1 {
-		label = "lan1";
-	};
-
-	port@2 {
-		label = "lan6";
-	};
-
-	port@3 {
-		label = "lan5";
-	};
-
-	/* External BCM53134S switch */
-	port@7 {
-		label = "sw";
-		reg = <7>;
-		phy-mode = "rgmii";
-
-		fixed-link {
-			speed = <1000>;
-			full-duplex;
-		};
-	};
-};
-
-&mdio {
-	/* lan8 */
-	ethernet-phy@0 {
-		reg = <0>;
-	};
-
-	/* lan7 */
-	ethernet-phy@1 {
-		reg = <1>;
-	};
-
-	/* lan4 */
-	ethernet-phy@2 {
-		reg = <2>;
-	};
-
-	/* lan3 */
-	ethernet-phy@3 {
-		reg = <3>;
-	};
-};
-
-&nandcs {
-	nand-ecc-strength = <4>;
-	nand-ecc-step-size = <512>;
-	nand-on-flash-bbt;
-	brcm,nand-has-wp;
-
-	#address-cells = <1>;
-	#size-cells = <0>;
-
-	partitions {
-		compatible = "brcm,bcm4908-partitions";
-		#address-cells = <1>;
-		#size-cells = <1>;
-
-		partition@0 {
-			compatible = "nvmem-cells";
-			label = "cferom";
-			reg = <0x0 0x100000>;
-
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges = <0 0x0 0x100000>;
-
-			base_mac_addr: mac@106a0 {
-				reg = <0x106a0 0x6>;
-			};
-		};
-
-		partition@100000 {
-			compatible = "brcm,bcm4908-firmware";
-			reg = <0x100000 0x5700000>;
-		};
-
-		partition@5800000 {
-			compatible = "brcm,bcm4908-firmware";
-			reg = <0x5800000 0x5700000>;
-		};
-	};
-};
diff --git a/arch/arm64/boot/dts/broadcom/bcm4908/bcm4908.dtsi b/arch/arm64/boot/dts/broadcom/bcm4908/bcm4908.dtsi
deleted file mode 100644
index 984c737fa627..000000000000
--- a/arch/arm64/boot/dts/broadcom/bcm4908/bcm4908.dtsi
+++ /dev/null
@@ -1,337 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
-
-#include <dt-bindings/interrupt-controller/irq.h>
-#include <dt-bindings/interrupt-controller/arm-gic.h>
-#include <dt-bindings/phy/phy.h>
-#include <dt-bindings/soc/bcm-pmb.h>
-
-/dts-v1/;
-
-/ {
-	interrupt-parent = <&gic>;
-
-	#address-cells = <2>;
-	#size-cells = <2>;
-
-	aliases {
-		serial0 = &uart0;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	cpus {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		cpu0: cpu@0 {
-			device_type = "cpu";
-			compatible = "brcm,brahma-b53";
-			reg = <0x0>;
-			next-level-cache = <&l2>;
-		};
-
-		cpu1: cpu@1 {
-			device_type = "cpu";
-			compatible = "brcm,brahma-b53";
-			reg = <0x1>;
-			enable-method = "spin-table";
-			cpu-release-addr = <0x0 0xfff8>;
-			next-level-cache = <&l2>;
-		};
-
-		cpu2: cpu@2 {
-			device_type = "cpu";
-			compatible = "brcm,brahma-b53";
-			reg = <0x2>;
-			enable-method = "spin-table";
-			cpu-release-addr = <0x0 0xfff8>;
-			next-level-cache = <&l2>;
-		};
-
-		cpu3: cpu@3 {
-			device_type = "cpu";
-			compatible = "brcm,brahma-b53";
-			reg = <0x3>;
-			enable-method = "spin-table";
-			cpu-release-addr = <0x0 0xfff8>;
-			next-level-cache = <&l2>;
-		};
-
-		l2: l2-cache0 {
-			compatible = "cache";
-		};
-	};
-
-	axi@81000000 {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges = <0x00 0x00 0x81000000 0x4000>;
-
-		gic: interrupt-controller@1000 {
-			compatible = "arm,gic-400";
-			#interrupt-cells = <3>;
-			#address-cells = <0>;
-			interrupt-controller;
-			reg = <0x1000 0x1000>,
-			      <0x2000 0x2000>;
-		};
-	};
-
-	timer {
-		compatible = "arm,armv8-timer";
-		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
-			     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
-			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
-			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
-	};
-
-	pmu {
-		compatible = "arm,cortex-a53-pmu";
-		interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
-			     <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,
-			     <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
-			     <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
-		interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>;
-	};
-
-	clocks {
-		periph_clk: periph_clk {
-			compatible = "fixed-clock";
-			#clock-cells = <0>;
-			clock-frequency = <50000000>;
-			clock-output-names = "periph";
-		};
-	};
-
-	soc {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges = <0x00 0x00 0x80000000 0x281000>;
-
-		enet: ethernet@2000 {
-			compatible = "brcm,bcm4908-enet";
-			reg = <0x2000 0x1000>;
-
-			interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "rx", "tx";
-		};
-
-		usb_phy: usb-phy@c200 {
-			compatible = "brcm,bcm4908-usb-phy";
-			reg = <0xc200 0x100>;
-			reg-names = "ctrl";
-			power-domains = <&pmb BCM_PMB_HOST_USB>;
-			dr_mode = "host";
-			brcm,has-xhci;
-			brcm,has-eohci;
-			#phy-cells = <1>;
-			status = "disabled";
-		};
-
-		ehci: usb@c300 {
-			compatible = "generic-ehci";
-			reg = <0xc300 0x100>;
-			interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
-			phys = <&usb_phy PHY_TYPE_USB2>;
-			status = "disabled";
-		};
-
-		ohci: usb@c400 {
-			compatible = "generic-ohci";
-			reg = <0xc400 0x100>;
-			interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
-			phys = <&usb_phy PHY_TYPE_USB2>;
-			status = "disabled";
-		};
-
-		xhci: usb@d000 {
-			compatible = "generic-xhci";
-			reg = <0xd000 0x8c8>;
-			interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
-			phys = <&usb_phy PHY_TYPE_USB3>;
-			status = "disabled";
-		};
-
-		bus@80000 {
-			compatible = "simple-bus";
-			#size-cells = <1>;
-			#address-cells = <1>;
-			ranges = <0 0x80000 0x50000>;
-
-			ethernet-switch@0 {
-				compatible = "brcm,bcm4908-switch";
-				reg = <0x0 0x40000>,
-				      <0x40000 0x110>,
-				      <0x40340 0x30>,
-				      <0x40380 0x30>,
-				      <0x40600 0x34>,
-				      <0x40800 0x208>;
-				reg-names = "core", "reg", "intrl2_0",
-					    "intrl2_1", "fcb", "acb";
-				interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>,
-					     <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>;
-				brcm,num-gphy = <5>;
-				brcm,num-rgmii-ports = <2>;
-
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				ports: ports {
-					#address-cells = <1>;
-					#size-cells = <0>;
-
-					port@0 {
-						reg = <0>;
-						phy-mode = "internal";
-						phy-handle = <&phy8>;
-					};
-
-					port@1 {
-						reg = <1>;
-						phy-mode = "internal";
-						phy-handle = <&phy9>;
-					};
-
-					port@2 {
-						reg = <2>;
-						phy-mode = "internal";
-						phy-handle = <&phy10>;
-					};
-
-					port@3 {
-						reg = <3>;
-						phy-mode = "internal";
-						phy-handle = <&phy11>;
-					};
-
-					port@8 {
-						reg = <8>;
-						phy-mode = "internal";
-						ethernet = <&enet>;
-
-						fixed-link {
-							speed = <1000>;
-							full-duplex;
-						};
-					};
-				};
-			};
-
-			mdio: mdio@405c0 {
-				compatible = "brcm,unimac-mdio";
-				reg = <0x405c0 0x8>;
-				reg-names = "mdio";
-				#size-cells = <0>;
-				#address-cells = <1>;
-
-				phy8: ethernet-phy@8 {
-					reg = <8>;
-				};
-
-				phy9: ethernet-phy@9 {
-					reg = <9>;
-				};
-
-				phy10: ethernet-phy@a {
-					reg = <10>;
-				};
-
-				phy11: ethernet-phy@b {
-					reg = <11>;
-				};
-
-				phy12: ethernet-phy@c {
-					reg = <12>;
-				};
-			};
-		};
-
-		procmon: syscon@280000 {
-			compatible = "simple-bus";
-			reg = <0x280000 0x1000>;
-			ranges;
-
-			#address-cells = <1>;
-			#size-cells = <1>;
-
-			pmb: power-controller@2800c0 {
-				compatible = "brcm,bcm4908-pmb";
-				reg = <0x2800c0 0x40>;
-				#power-domain-cells = <1>;
-			};
-		};
-	};
-
-	bus@ff800000 {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges = <0x00 0x00 0xff800000 0x3000>;
-
-		timer: timer@400 {
-			compatible = "brcm,bcm6328-timer", "syscon";
-			reg = <0x400 0x3c>;
-		};
-
-		gpio0: gpio-controller@500 {
-			compatible = "brcm,bcm6345-gpio";
-			reg-names = "dirout", "dat";
-			reg = <0x500 0x28>, <0x528 0x28>;
-
-			#gpio-cells = <2>;
-			gpio-controller;
-		};
-
-		uart0: serial@640 {
-			compatible = "brcm,bcm6345-uart";
-			reg = <0x640 0x18>;
-			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&periph_clk>;
-			clock-names = "refclk";
-			status = "okay";
-		};
-
-		nand-controller@1800 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			compatible = "brcm,nand-bcm63138", "brcm,brcmnand-v7.1", "brcm,brcmnand";
-			reg = <0x1800 0x600>, <0x2000 0x10>;
-			reg-names = "nand", "nand-int-base";
-			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "nand";
-			status = "okay";
-
-			nandcs: nand@0 {
-				compatible = "brcm,nandcs";
-				reg = <0>;
-			};
-		};
-
-		misc@2600 {
-			compatible = "brcm,misc", "simple-mfd";
-			reg = <0x2600 0xe4>;
-
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges = <0x00 0x2600 0xe4>;
-
-			reset-controller@2644 {
-				compatible = "brcm,bcm4908-misc-pcie-reset";
-				reg = <0x44 0x04>;
-				#reset-cells = <1>;
-			};
-		};
-	};
-
-	reboot {
-		compatible = "syscon-reboot";
-		regmap = <&timer>;
-		offset = <0x34>;
-		mask = <1>;
-	};
-};
diff --git a/arch/arm64/boot/dts/broadcom/bcmbca/Makefile b/arch/arm64/boot/dts/broadcom/bcmbca/Makefile
new file mode 100644
index 000000000000..27741b71ba9e
--- /dev/null
+++ b/arch/arm64/boot/dts/broadcom/bcmbca/Makefile
@@ -0,0 +1,14 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_BCMBCA) += \
+				bcm4906-netgear-r8000p.dtb \
+				bcm4906-tplink-archer-c2300-v1.dtb \
+				bcm4908-asus-gt-ac5300.dtb \
+				bcm4908-netgear-raxe500.dtb \
+				bcm94908.dtb \
+				bcm4912-asus-gt-ax6000.dtb \
+				bcm94912.dtb \
+				bcm963158.dtb \
+				bcm96858.dtb \
+				bcm963146.dtb \
+				bcm96856.dtb \
+				bcm96813.dtb
diff --git a/arch/arm64/boot/dts/broadcom/bcm4908/bcm4906-netgear-r8000p.dts b/arch/arm64/boot/dts/broadcom/bcmbca/bcm4906-netgear-r8000p.dts
index 2dd028438c22..d8b60575eb4f 100644
--- a/arch/arm64/boot/dts/broadcom/bcm4908/bcm4906-netgear-r8000p.dts
+++ b/arch/arm64/boot/dts/broadcom/bcmbca/bcm4906-netgear-r8000p.dts
@@ -7,7 +7,7 @@
 #include "bcm4906.dtsi"
 
 / {
-	compatible = "netgear,r8000p", "brcm,bcm4906", "brcm,bcm4908";
+	compatible = "netgear,r8000p", "brcm,bcm4906", "brcm,bcm4908", "brcm,bcmbca";
 	model = "Netgear R8000P";
 
 	memory@0 {
diff --git a/arch/arm64/boot/dts/broadcom/bcm4908/bcm4906-tplink-archer-c2300-v1.dts b/arch/arm64/boot/dts/broadcom/bcmbca/bcm4906-tplink-archer-c2300-v1.dts
index b63eefab48bd..296393d4aaab 100644
--- a/arch/arm64/boot/dts/broadcom/bcm4908/bcm4906-tplink-archer-c2300-v1.dts
+++ b/arch/arm64/boot/dts/broadcom/bcmbca/bcm4906-tplink-archer-c2300-v1.dts
@@ -7,7 +7,7 @@
 #include "bcm4906.dtsi"
 
 / {
-	compatible = "tplink,archer-c2300-v1", "brcm,bcm4906", "brcm,bcm4908";
+	compatible = "tplink,archer-c2300-v1", "brcm,bcm4906", "brcm,bcm4908", "brcm,bcmbca";
 	model = "TP-Link Archer C2300 V1";
 
 	memory@0 {
@@ -83,25 +83,25 @@
 		compatible = "gpio-keys-polled";
 		poll-interval = <100>;
 
-		brightness {
+		key-brightness {
 			label = "LEDs";
 			linux,code = <KEY_BRIGHTNESS_ZERO>;
 			gpios = <&gpio0 18 GPIO_ACTIVE_LOW>;
 		};
 
-		wps {
+		key-wps {
 			label = "WPS";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&gpio0 21 GPIO_ACTIVE_LOW>;
 		};
 
-		wifi {
+		key-wifi {
 			label = "WiFi";
 			linux,code = <KEY_RFKILL>;
 			gpios = <&gpio0 22 GPIO_ACTIVE_LOW>;
 		};
 
-		restart {
+		key-restart {
 			label = "Reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&gpio0 23 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm64/boot/dts/broadcom/bcmbca/bcm4906.dtsi b/arch/arm64/boot/dts/broadcom/bcmbca/bcm4906.dtsi
new file mode 100644
index 000000000000..d084c33d5ca8
--- /dev/null
+++ b/arch/arm64/boot/dts/broadcom/bcmbca/bcm4906.dtsi
@@ -0,0 +1,26 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "bcm4908.dtsi"
+
+/ {
+	cpus {
+		/delete-node/ cpu@2;
+
+		/delete-node/ cpu@3;
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>;
+	};
+
+	pmu {
+		compatible = "arm,cortex-a53-pmu";
+		interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&cpu0>, <&cpu1>;
+	};
+};
diff --git a/arch/arm64/boot/dts/broadcom/bcmbca/bcm4908-asus-gt-ac5300.dts b/arch/arm64/boot/dts/broadcom/bcmbca/bcm4908-asus-gt-ac5300.dts
new file mode 100644
index 000000000000..839ca33178b0
--- /dev/null
+++ b/arch/arm64/boot/dts/broadcom/bcmbca/bcm4908-asus-gt-ac5300.dts
@@ -0,0 +1,207 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+
+#include "bcm4908.dtsi"
+
+/ {
+	compatible = "asus,gt-ac5300", "brcm,bcm4908", "brcm,bcmbca";
+	model = "Asus GT-AC5300";
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00 0x00 0x00 0x40000000>;
+	};
+
+	gpio-keys-polled {
+		compatible = "gpio-keys-polled";
+		poll-interval = <100>;
+
+		key-wifi {
+			label = "WiFi";
+			linux,code = <KEY_RFKILL>;
+			gpios = <&gpio0 28 GPIO_ACTIVE_LOW>;
+		};
+
+		key-wps {
+			label = "WPS";
+			linux,code = <KEY_WPS_BUTTON>;
+			gpios = <&gpio0 29 GPIO_ACTIVE_LOW>;
+		};
+
+		key-restart {
+			label = "Reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&gpio0 30 GPIO_ACTIVE_LOW>;
+		};
+
+		key-brightness {
+			label = "LEDs";
+			linux,code = <KEY_BRIGHTNESS_ZERO>;
+			gpios = <&gpio0 31 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&enet {
+	nvmem-cells = <&base_mac_addr>;
+	nvmem-cell-names = "mac-address";
+};
+
+&usb_phy {
+	brcm,ioc = <1>;
+	status = "okay";
+};
+
+&ehci {
+	status = "okay";
+};
+
+&ohci {
+	status = "okay";
+};
+
+&xhci {
+	status = "okay";
+};
+
+&ports {
+	port@0 {
+		label = "lan2";
+	};
+
+	port@1 {
+		label = "lan1";
+	};
+
+	port@2 {
+		label = "lan6";
+	};
+
+	port@3 {
+		label = "lan5";
+	};
+
+	/* External BCM53134S switch */
+	port@7 {
+		label = "sw";
+		reg = <7>;
+		phy-mode = "rgmii";
+
+		fixed-link {
+			speed = <1000>;
+			full-duplex;
+		};
+	};
+};
+
+&mdio {
+	/* lan8 */
+	ethernet-phy@0 {
+		reg = <0>;
+	};
+
+	/* lan7 */
+	ethernet-phy@1 {
+		reg = <1>;
+	};
+
+	/* lan4 */
+	ethernet-phy@2 {
+		reg = <2>;
+	};
+
+	/* lan3 */
+	ethernet-phy@3 {
+		reg = <3>;
+	};
+};
+
+&leds {
+	led-power@11 {
+		reg = <0x11>;
+		function = LED_FUNCTION_POWER;
+		color = <LED_COLOR_ID_WHITE>;
+		default-state = "on";
+		active-low;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pins_led_17_a>;
+	};
+
+	led-wan-red@12 {
+		reg = <0x12>;
+		function = LED_FUNCTION_WAN;
+		color = <LED_COLOR_ID_RED>;
+		active-low;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pins_led_18_a>;
+	};
+
+	led-wps@14 {
+		reg = <0x14>;
+		function = LED_FUNCTION_WPS;
+		color = <LED_COLOR_ID_WHITE>;
+		active-low;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pins_led_20_a>;
+	};
+
+	led-wan-white@15 {
+		reg = <0x15>;
+		function = LED_FUNCTION_WAN;
+		color = <LED_COLOR_ID_WHITE>;
+		active-low;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pins_led_21_a>;
+	};
+
+	led-lan@19 {
+		reg = <0x19>;
+		function = LED_FUNCTION_LAN;
+		color = <LED_COLOR_ID_WHITE>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pins_led_25_a>;
+	};
+};
+
+&nandcs {
+	nand-ecc-strength = <4>;
+	nand-ecc-step-size = <512>;
+	nand-on-flash-bbt;
+	brcm,nand-has-wp;
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	partitions {
+		compatible = "brcm,bcm4908-partitions";
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		partition@0 {
+			compatible = "nvmem-cells";
+			label = "cferom";
+			reg = <0x0 0x100000>;
+
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x0 0x100000>;
+
+			base_mac_addr: mac@106a0 {
+				reg = <0x106a0 0x6>;
+			};
+		};
+
+		partition@100000 {
+			compatible = "brcm,bcm4908-firmware";
+			reg = <0x100000 0x5700000>;
+		};
+
+		partition@5800000 {
+			compatible = "brcm,bcm4908-firmware";
+			reg = <0x5800000 0x5700000>;
+		};
+	};
+};
diff --git a/arch/arm64/boot/dts/broadcom/bcmbca/bcm4908-netgear-raxe500.dts b/arch/arm64/boot/dts/broadcom/bcmbca/bcm4908-netgear-raxe500.dts
new file mode 100644
index 000000000000..23b96c663239
--- /dev/null
+++ b/arch/arm64/boot/dts/broadcom/bcmbca/bcm4908-netgear-raxe500.dts
@@ -0,0 +1,50 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "bcm4908.dtsi"
+
+/ {
+	compatible = "netgear,raxe500", "brcm,bcm4908", "brcm,bcmbca";
+	model = "Netgear RAXE500";
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00 0x00 0x00 0x40000000>;
+	};
+};
+
+&ehci {
+	status = "okay";
+};
+
+&ohci {
+	status = "okay";
+};
+
+&xhci {
+	status = "okay";
+};
+
+&ports {
+	port@0 {
+		label = "lan4";
+	};
+
+	port@1 {
+		label = "lan3";
+	};
+
+	port@2 {
+		label = "lan2";
+	};
+
+	port@3 {
+		label = "lan1";
+	};
+
+	port@7 {
+		reg = <7>;
+		phy-mode = "internal";
+		phy-handle = <&phy12>;
+		label = "wan";
+	};
+};
diff --git a/arch/arm64/boot/dts/broadcom/bcmbca/bcm4908.dtsi b/arch/arm64/boot/dts/broadcom/bcmbca/bcm4908.dtsi
new file mode 100644
index 000000000000..dac9d3b4e91d
--- /dev/null
+++ b/arch/arm64/boot/dts/broadcom/bcmbca/bcm4908.dtsi
@@ -0,0 +1,575 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/phy/phy.h>
+#include <dt-bindings/soc/bcm-pmb.h>
+
+/dts-v1/;
+
+/ {
+	interrupt-parent = <&gic>;
+
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "brcm,brahma-b53";
+			reg = <0x0>;
+			enable-method = "spin-table";
+			cpu-release-addr = <0x0 0xfff8>;
+			next-level-cache = <&l2>;
+		};
+
+		cpu1: cpu@1 {
+			device_type = "cpu";
+			compatible = "brcm,brahma-b53";
+			reg = <0x1>;
+			enable-method = "spin-table";
+			cpu-release-addr = <0x0 0xfff8>;
+			next-level-cache = <&l2>;
+		};
+
+		cpu2: cpu@2 {
+			device_type = "cpu";
+			compatible = "brcm,brahma-b53";
+			reg = <0x2>;
+			enable-method = "spin-table";
+			cpu-release-addr = <0x0 0xfff8>;
+			next-level-cache = <&l2>;
+		};
+
+		cpu3: cpu@3 {
+			device_type = "cpu";
+			compatible = "brcm,brahma-b53";
+			reg = <0x3>;
+			enable-method = "spin-table";
+			cpu-release-addr = <0x0 0xfff8>;
+			next-level-cache = <&l2>;
+		};
+
+		l2: l2-cache0 {
+			compatible = "cache";
+		};
+	};
+
+	axi@81000000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x00 0x00 0x81000000 0x4000>;
+
+		gic: interrupt-controller@1000 {
+			compatible = "arm,gic-400";
+			#interrupt-cells = <3>;
+			#address-cells = <0>;
+			interrupt-controller;
+			reg = <0x1000 0x1000>,
+			      <0x2000 0x2000>;
+		};
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+	};
+
+	pmu {
+		compatible = "arm,cortex-a53-pmu";
+		interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>;
+	};
+
+	clocks {
+		periph_clk: periph_clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <50000000>;
+			clock-output-names = "periph";
+		};
+	};
+
+	soc {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x00 0x00 0x80000000 0x281000>;
+
+		enet: ethernet@2000 {
+			compatible = "brcm,bcm4908-enet";
+			reg = <0x2000 0x1000>;
+
+			interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "rx", "tx";
+		};
+
+		usb_phy: usb-phy@c200 {
+			compatible = "brcm,bcm4908-usb-phy";
+			reg = <0xc200 0x100>;
+			reg-names = "ctrl";
+			power-domains = <&pmb BCM_PMB_HOST_USB>;
+			dr_mode = "host";
+			brcm,has-xhci;
+			brcm,has-eohci;
+			#phy-cells = <1>;
+			status = "disabled";
+		};
+
+		ehci: usb@c300 {
+			compatible = "generic-ehci";
+			reg = <0xc300 0x100>;
+			interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
+			phys = <&usb_phy PHY_TYPE_USB2>;
+			status = "disabled";
+		};
+
+		ohci: usb@c400 {
+			compatible = "generic-ohci";
+			reg = <0xc400 0x100>;
+			interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
+			phys = <&usb_phy PHY_TYPE_USB2>;
+			status = "disabled";
+		};
+
+		xhci: usb@d000 {
+			compatible = "generic-xhci";
+			reg = <0xd000 0x8c8>;
+			interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
+			phys = <&usb_phy PHY_TYPE_USB3>;
+			status = "disabled";
+		};
+
+		bus@80000 {
+			compatible = "simple-bus";
+			#size-cells = <1>;
+			#address-cells = <1>;
+			ranges = <0 0x80000 0x50000>;
+
+			ethernet-switch@0 {
+				compatible = "brcm,bcm4908-switch";
+				reg = <0x0 0x40000>,
+				      <0x40000 0x110>,
+				      <0x40340 0x30>,
+				      <0x40380 0x30>,
+				      <0x40600 0x34>,
+				      <0x40800 0x208>;
+				reg-names = "core", "reg", "intrl2_0",
+					    "intrl2_1", "fcb", "acb";
+				interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>;
+				brcm,num-gphy = <5>;
+				brcm,num-rgmii-ports = <2>;
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				ports: ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+						phy-mode = "internal";
+						phy-handle = <&phy8>;
+					};
+
+					port@1 {
+						reg = <1>;
+						phy-mode = "internal";
+						phy-handle = <&phy9>;
+					};
+
+					port@2 {
+						reg = <2>;
+						phy-mode = "internal";
+						phy-handle = <&phy10>;
+					};
+
+					port@3 {
+						reg = <3>;
+						phy-mode = "internal";
+						phy-handle = <&phy11>;
+					};
+
+					port@8 {
+						reg = <8>;
+						phy-mode = "internal";
+						ethernet = <&enet>;
+
+						fixed-link {
+							speed = <1000>;
+							full-duplex;
+						};
+					};
+				};
+			};
+
+			mdio: mdio@405c0 {
+				compatible = "brcm,unimac-mdio";
+				reg = <0x405c0 0x8>;
+				reg-names = "mdio";
+				#size-cells = <0>;
+				#address-cells = <1>;
+
+				phy8: ethernet-phy@8 {
+					reg = <8>;
+				};
+
+				phy9: ethernet-phy@9 {
+					reg = <9>;
+				};
+
+				phy10: ethernet-phy@a {
+					reg = <10>;
+				};
+
+				phy11: ethernet-phy@b {
+					reg = <11>;
+				};
+
+				phy12: ethernet-phy@c {
+					reg = <12>;
+				};
+			};
+		};
+
+		procmon: syscon@280000 {
+			compatible = "simple-bus";
+			reg = <0x280000 0x1000>;
+			ranges;
+
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			pmb: power-controller@2800c0 {
+				compatible = "brcm,bcm4908-pmb";
+				reg = <0x2800c0 0x40>;
+				#power-domain-cells = <1>;
+			};
+		};
+	};
+
+	bus@ff800000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x00 0x00 0xff800000 0x3000>;
+
+		twd: timer-mfd@400 {
+			compatible = "brcm,bcm4908-twd", "simple-mfd", "syscon";
+			reg = <0x400 0x4c>;
+			ranges = <0x0 0x400 0x4c>;
+
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			watchdog@28 {
+				compatible = "brcm,bcm6345-wdt";
+				reg = <0x28 0x8>;
+			};
+		};
+
+		gpio0: gpio-controller@500 {
+			compatible = "brcm,bcm6345-gpio";
+			reg-names = "dirout", "dat";
+			reg = <0x500 0x28>, <0x528 0x28>;
+
+			#gpio-cells = <2>;
+			gpio-controller;
+		};
+
+		pinctrl@560 {
+			compatible = "brcm,bcm4908-pinctrl";
+			reg = <0x560 0x10>;
+
+			pins_led_0_a: led_0-a-pins {
+				function = "led_0";
+				groups = "led_0_grp_a";
+			};
+
+			pins_led_1_a: led_1-a-pins {
+				function = "led_1";
+				groups = "led_1_grp_a";
+			};
+
+			pins_led_2_a: led_2-a-pins {
+				function = "led_2";
+				groups = "led_2_grp_a";
+			};
+
+			pins_led_3_a: led_3-a-pins {
+				function = "led_3";
+				groups = "led_3_grp_a";
+			};
+
+			pins_led_4_a: led_4-a-pins {
+				function = "led_4";
+				groups = "led_4_grp_a";
+			};
+
+			pins_led_5_a: led_5-a-pins {
+				function = "led_5";
+				groups = "led_5_grp_a";
+			};
+
+			pins_led_6_a: led_6-a-pins {
+				function = "led_6";
+				groups = "led_6_grp_a";
+			};
+
+			pins_led_7_a: led_7-a-pins {
+				function = "led_7";
+				groups = "led_7_grp_a";
+			};
+
+			pins_led_8_a: led_8-a-pins {
+				function = "led_8";
+				groups = "led_8_grp_a";
+			};
+
+			pins_led_9_a: led_9-a-pins {
+				function = "led_9";
+				groups = "led_9_grp_a";
+			};
+
+			pins_led_10_a: led_10-a-pins {
+				function = "led_10";
+				groups = "led_10_grp_a";
+			};
+
+			pins_led_11_a: led_11-a-pins {
+				function = "led_11";
+				groups = "led_11_grp_a";
+			};
+
+			pins_led_12_a: led_12-a-pins {
+				function = "led_12";
+				groups = "led_12_grp_a";
+			};
+
+			pins_led_13_a: led_13-a-pins {
+				function = "led_13";
+				groups = "led_13_grp_a";
+			};
+
+			pins_led_14_a: led_14-a-pins {
+				function = "led_14";
+				groups = "led_14_grp_a";
+			};
+
+			pins_led_15_a: led_15-a-pins {
+				function = "led_15";
+				groups = "led_15_grp_a";
+			};
+
+			pins_led_16_a: led_16-a-pins {
+				function = "led_16";
+				groups = "led_16_grp_a";
+			};
+
+			pins_led_17_a: led_17-a-pins {
+				function = "led_17";
+				groups = "led_17_grp_a";
+			};
+
+			pins_led_18_a: led_18-a-pins {
+				function = "led_18";
+				groups = "led_18_grp_a";
+			};
+
+			pins_led_19_a: led_19-a-pins {
+				function = "led_19";
+				groups = "led_19_grp_a";
+			};
+
+			pins_led_20_a: led_20-a-pins {
+				function = "led_20";
+				groups = "led_20_grp_a";
+			};
+
+			pins_led_21_a: led_21-a-pins {
+				function = "led_21";
+				groups = "led_21_grp_a";
+			};
+
+			pins_led_22_a: led_22-a-pins {
+				function = "led_22";
+				groups = "led_22_grp_a";
+			};
+
+			pins_led_23_a: led_23-a-pins {
+				function = "led_23";
+				groups = "led_23_grp_a";
+			};
+
+			pins_led_24_a: led_24-a-pins {
+				function = "led_24";
+				groups = "led_24_grp_a";
+			};
+
+			pins_led_25_a: led_25-a-pins {
+				function = "led_25";
+				groups = "led_25_grp_a";
+			};
+
+			pins_led_26_a: led_26-a-pins {
+				function = "led_26";
+				groups = "led_26_grp_a";
+			};
+
+			pins_led_27_a: led_27-a-pins {
+				function = "led_27";
+				groups = "led_27_grp_a";
+			};
+
+			pins_led_28_a: led_28-a-pins {
+				function = "led_28";
+				groups = "led_28_grp_a";
+			};
+
+			pins_led_29_a: led_29-a-pins {
+				function = "led_29";
+				groups = "led_29_grp_a";
+			};
+
+			pins_led_30_a: led_30-a-pins {
+				function = "led_30";
+				groups = "led_30_grp_a";
+			};
+
+			pins_led_31_a: led_31-a-pins {
+				function = "led_31";
+				groups = "led_31_grp_a";
+			};
+
+			pins_hs_uart: hs_uart-pins {
+				function = "hs_uart";
+				groups = "hs_uart_grp";
+			};
+
+			pins_i2c_a: i2c-a-pins {
+				function = "i2c";
+				groups = "i2c_grp_a";
+			};
+
+			pins_i2c_b: i2c-b-pins {
+				function = "i2c";
+				groups = "i2c_grp_b";
+			};
+
+			pins_i2s: i2s-pins {
+				function = "i2s";
+				groups = "i2s_grp";
+			};
+
+			pins_nand_ctrl: nand_ctrl-pins {
+				function = "nand_ctrl";
+				groups = "nand_ctrl_grp";
+			};
+
+			pins_nand_data: nand_data-pins {
+				function = "nand_data";
+				groups = "nand_data_grp";
+			};
+
+			pins_emmc_ctrl: emmc_ctrl-pins {
+				function = "emmc_ctrl";
+				groups = "emmc_ctrl_grp";
+			};
+
+			pins_usb0_pwr: usb0_pwr-pins {
+				function = "usb0_pwr";
+				groups = "usb0_pwr_grp";
+			};
+
+			pins_usb1_pwr: usb1_pwr-pins {
+				function = "usb1_pwr";
+				groups = "usb1_pwr_grp";
+			};
+		};
+
+		uart0: serial@640 {
+			compatible = "brcm,bcm6345-uart";
+			reg = <0x640 0x18>;
+			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&periph_clk>;
+			clock-names = "refclk";
+			status = "okay";
+		};
+
+		leds: leds@800 {
+			compatible = "brcm,bcm4908-leds", "brcm,bcm63138-leds";
+			reg = <0x800 0xdc>;
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		nand-controller@1800 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,nand-bcm63138", "brcm,brcmnand-v7.1", "brcm,brcmnand";
+			reg = <0x1800 0x600>, <0x2000 0x10>;
+			reg-names = "nand", "nand-int-base";
+			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "nand";
+			status = "okay";
+
+			nandcs: nand@0 {
+				compatible = "brcm,nandcs";
+				reg = <0>;
+			};
+		};
+
+		i2c@2100 {
+			compatible = "brcm,brcmper-i2c";
+			reg = <0x2100 0x58>;
+			clock-frequency = <97500>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pins_i2c_a>;
+			status = "disabled";
+		};
+
+		misc@2600 {
+			compatible = "brcm,misc", "simple-mfd";
+			reg = <0x2600 0xe4>;
+
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x00 0x2600 0xe4>;
+
+			reset-controller@2644 {
+				compatible = "brcm,bcm4908-misc-pcie-reset";
+				reg = <0x44 0x04>;
+				#reset-cells = <1>;
+			};
+		};
+	};
+
+	reboot {
+		compatible = "syscon-reboot";
+		regmap = <&twd>;
+		offset = <0x34>;
+		mask = <1>;
+	};
+};
diff --git a/arch/arm64/boot/dts/broadcom/bcmbca/bcm4912-asus-gt-ax6000.dts b/arch/arm64/boot/dts/broadcom/bcmbca/bcm4912-asus-gt-ax6000.dts
new file mode 100644
index 000000000000..ed554666e95e
--- /dev/null
+++ b/arch/arm64/boot/dts/broadcom/bcmbca/bcm4912-asus-gt-ax6000.dts
@@ -0,0 +1,19 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+/dts-v1/;
+
+#include "bcm4912.dtsi"
+
+/ {
+	compatible = "asus,gt-ax6000", "brcm,bcm4912", "brcm,bcmbca";
+	model = "Asus GT-AX6000";
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00 0x00 0x00 0x40000000>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/broadcom/bcmbca/bcm4912.dtsi b/arch/arm64/boot/dts/broadcom/bcmbca/bcm4912.dtsi
new file mode 100644
index 000000000000..3d016c2ce675
--- /dev/null
+++ b/arch/arm64/boot/dts/broadcom/bcmbca/bcm4912.dtsi
@@ -0,0 +1,128 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2022 Broadcom Ltd.
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+	compatible = "brcm,bcm4912", "brcm,bcmbca";
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	interrupt-parent = <&gic>;
+
+	cpus {
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		B53_0: cpu@0 {
+			compatible = "brcm,brahma-b53";
+			device_type = "cpu";
+			reg = <0x0 0x0>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		B53_1: cpu@1 {
+			compatible = "brcm,brahma-b53";
+			device_type = "cpu";
+			reg = <0x0 0x1>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		B53_2: cpu@2 {
+			compatible = "brcm,brahma-b53";
+			device_type = "cpu";
+			reg = <0x0 0x2>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		B53_3: cpu@3 {
+			compatible = "brcm,brahma-b53";
+			device_type = "cpu";
+			reg = <0x0 0x3>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		L2_0: l2-cache0 {
+			compatible = "cache";
+		};
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+	};
+
+	pmu: pmu {
+		compatible = "arm,cortex-a53-pmu";
+		interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&B53_0>, <&B53_1>,
+			<&B53_2>, <&B53_3>;
+	};
+
+	clocks: clocks {
+		periph_clk: periph-clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <200000000>;
+		};
+		uart_clk: uart-clk {
+			compatible = "fixed-factor-clock";
+			#clock-cells = <0>;
+			clocks = <&periph_clk>;
+			clock-div = <4>;
+			clock-mult = <1>;
+		};
+	};
+
+	psci {
+		compatible = "arm,psci-0.2";
+		method = "smc";
+	};
+
+	axi@81000000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x0 0x81000000 0x8000>;
+
+		gic: interrupt-controller@1000 {
+			compatible = "arm,gic-400";
+			#interrupt-cells = <3>;
+			interrupt-controller;
+			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+			reg = <0x1000 0x1000>,
+				<0x2000 0x2000>,
+				<0x4000 0x2000>,
+				<0x6000 0x2000>;
+		};
+	};
+
+	bus@ff800000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x0 0xff800000 0x800000>;
+
+		uart0: serial@12000 {
+			compatible = "arm,pl011", "arm,primecell";
+			reg = <0x12000 0x1000>;
+			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&uart_clk>, <&uart_clk>;
+			clock-names = "uartclk", "apb_pclk";
+			status = "disabled";
+		};
+	};
+};
diff --git a/arch/arm64/boot/dts/broadcom/bcmbca/bcm63146.dtsi b/arch/arm64/boot/dts/broadcom/bcmbca/bcm63146.dtsi
new file mode 100644
index 000000000000..04de96bd0a03
--- /dev/null
+++ b/arch/arm64/boot/dts/broadcom/bcmbca/bcm63146.dtsi
@@ -0,0 +1,110 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2022 Broadcom Ltd.
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+	compatible = "brcm,bcm63146", "brcm,bcmbca";
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	interrupt-parent = <&gic>;
+
+	cpus {
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		B53_0: cpu@0 {
+			compatible = "brcm,brahma-b53";
+			device_type = "cpu";
+			reg = <0x0 0x0>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		B53_1: cpu@1 {
+			compatible = "brcm,brahma-b53";
+			device_type = "cpu";
+			reg = <0x0 0x1>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		L2_0: l2-cache0 {
+			compatible = "cache";
+		};
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>;
+	};
+
+	pmu: pmu {
+		compatible = "arm,cortex-a53-pmu";
+		interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&B53_0>, <&B53_1>;
+	};
+
+	clocks: clocks {
+		periph_clk: periph-clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <200000000>;
+		};
+		uart_clk: uart-clk {
+			compatible = "fixed-factor-clock";
+			#clock-cells = <0>;
+			clocks = <&periph_clk>;
+			clock-div = <4>;
+			clock-mult = <1>;
+		};
+	};
+
+	psci {
+		compatible = "arm,psci-0.2";
+		method = "smc";
+	};
+
+	axi@81000000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x0 0x81000000 0x8000>;
+
+		gic: interrupt-controller@1000 {
+			compatible = "arm,gic-400";
+			#interrupt-cells = <3>;
+			interrupt-controller;
+			reg = <0x1000 0x1000>,
+				<0x2000 0x2000>,
+				<0x4000 0x2000>,
+				<0x6000 0x2000>;
+			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(2) |
+					IRQ_TYPE_LEVEL_HIGH)>;
+		};
+	};
+
+	bus@ff800000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x0 0xff800000 0x800000>;
+
+		uart0: serial@12000 {
+			compatible = "arm,pl011", "arm,primecell";
+			reg = <0x12000 0x1000>;
+			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&uart_clk>, <&uart_clk>;
+			clock-names = "uartclk", "apb_pclk";
+			status = "disabled";
+		};
+	};
+};
diff --git a/arch/arm64/boot/dts/broadcom/bcmbca/bcm63158.dtsi b/arch/arm64/boot/dts/broadcom/bcmbca/bcm63158.dtsi
new file mode 100644
index 000000000000..13629702f70b
--- /dev/null
+++ b/arch/arm64/boot/dts/broadcom/bcmbca/bcm63158.dtsi
@@ -0,0 +1,128 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2022 Broadcom Ltd.
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+	compatible = "brcm,bcm63158", "brcm,bcmbca";
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	interrupt-parent = <&gic>;
+
+	cpus {
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		B53_0: cpu@0 {
+			compatible = "brcm,brahma-b53";
+			device_type = "cpu";
+			reg = <0x0 0x0>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		B53_1: cpu@1 {
+			compatible = "brcm,brahma-b53";
+			device_type = "cpu";
+			reg = <0x0 0x1>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		B53_2: cpu@2 {
+			compatible = "brcm,brahma-b53";
+			device_type = "cpu";
+			reg = <0x0 0x2>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		B53_3: cpu@3 {
+			compatible = "brcm,brahma-b53";
+			device_type = "cpu";
+			reg = <0x0 0x3>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		L2_0: l2-cache0 {
+			compatible = "cache";
+		};
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+	};
+
+	pmu: pmu {
+		compatible = "arm,cortex-a53-pmu";
+		interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&B53_0>, <&B53_1>,
+			<&B53_2>, <&B53_3>;
+	};
+
+	clocks: clocks {
+		periph_clk: periph-clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <200000000>;
+		};
+		uart_clk: uart-clk {
+			compatible = "fixed-factor-clock";
+			#clock-cells = <0>;
+			clocks = <&periph_clk>;
+			clock-div = <4>;
+			clock-mult = <1>;
+		};
+	};
+
+	psci {
+		compatible = "arm,psci-0.2";
+		method = "smc";
+	};
+
+	axi@81000000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x0 0x81000000 0x8000>;
+
+		gic: interrupt-controller@1000 {
+			compatible = "arm,gic-400";
+			#interrupt-cells = <3>;
+			interrupt-controller;
+			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+			reg = <0x1000 0x1000>,
+				<0x2000 0x2000>,
+				<0x4000 0x2000>,
+				<0x6000 0x2000>;
+		};
+	};
+
+	bus@ff800000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x0 0xff800000 0x800000>;
+
+		uart0: serial@12000 {
+			compatible = "arm,pl011", "arm,primecell";
+			reg = <0x12000 0x1000>;
+			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&uart_clk>, <&uart_clk>;
+			clock-names = "uartclk", "apb_pclk";
+			status = "disabled";
+		};
+	};
+};
diff --git a/arch/arm64/boot/dts/broadcom/bcmbca/bcm6813.dtsi b/arch/arm64/boot/dts/broadcom/bcmbca/bcm6813.dtsi
new file mode 100644
index 000000000000..c3e6197be808
--- /dev/null
+++ b/arch/arm64/boot/dts/broadcom/bcmbca/bcm6813.dtsi
@@ -0,0 +1,128 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2022 Broadcom Ltd.
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+	compatible = "brcm,bcm6813", "brcm,bcmbca";
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	interrupt-parent = <&gic>;
+
+	cpus {
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		B53_0: cpu@0 {
+			compatible = "brcm,brahma-b53";
+			device_type = "cpu";
+			reg = <0x0 0x0>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		B53_1: cpu@1 {
+			compatible = "brcm,brahma-b53";
+			device_type = "cpu";
+			reg = <0x0 0x1>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		B53_2: cpu@2 {
+			compatible = "brcm,brahma-b53";
+			device_type = "cpu";
+			reg = <0x0 0x2>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		B53_3: cpu@3 {
+			compatible = "brcm,brahma-b53";
+			device_type = "cpu";
+			reg = <0x0 0x3>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		L2_0: l2-cache0 {
+			compatible = "cache";
+		};
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+	};
+
+	pmu: pmu {
+		compatible = "arm,cortex-a53-pmu";
+		interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&B53_0>, <&B53_1>,
+			<&B53_2>, <&B53_3>;
+	};
+
+	clocks: clocks {
+		periph_clk: periph-clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <200000000>;
+		};
+		uart_clk: uart-clk {
+			compatible = "fixed-factor-clock";
+			#clock-cells = <0>;
+			clocks = <&periph_clk>;
+			clock-div = <4>;
+			clock-mult = <1>;
+		};
+	};
+
+	psci {
+		compatible = "arm,psci-0.2";
+		method = "smc";
+	};
+
+	axi@81000000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x0 0x81000000 0x8000>;
+
+		gic: interrupt-controller@1000 {
+			compatible = "arm,gic-400";
+			#interrupt-cells = <3>;
+			interrupt-controller;
+			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+			reg = <0x1000 0x1000>,
+				<0x2000 0x2000>,
+				<0x4000 0x2000>,
+				<0x6000 0x2000>;
+		};
+	};
+
+	bus@ff800000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x0 0xff800000 0x800000>;
+
+		uart0: serial@12000 {
+			compatible = "arm,pl011", "arm,primecell";
+			reg = <0x12000 0x1000>;
+			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&uart_clk>, <&uart_clk>;
+			clock-names = "uartclk", "apb_pclk";
+			status = "disabled";
+		};
+	};
+};
diff --git a/arch/arm64/boot/dts/broadcom/bcmbca/bcm6856.dtsi b/arch/arm64/boot/dts/broadcom/bcmbca/bcm6856.dtsi
new file mode 100644
index 000000000000..0bce6497219f
--- /dev/null
+++ b/arch/arm64/boot/dts/broadcom/bcmbca/bcm6856.dtsi
@@ -0,0 +1,103 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2022 Broadcom Ltd.
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+	compatible = "brcm,bcm6856", "brcm,bcmbca";
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	interrupt-parent = <&gic>;
+
+	cpus {
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		B53_0: cpu@0 {
+			compatible = "brcm,brahma-b53";
+			device_type = "cpu";
+			reg = <0x0 0x0>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		B53_1: cpu@1 {
+			compatible = "brcm,brahma-b53";
+			device_type = "cpu";
+			reg = <0x0 0x1>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		L2_0: l2-cache0 {
+			compatible = "cache";
+		};
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>;
+	};
+
+	pmu: pmu {
+		compatible = "arm,cortex-a53-pmu";
+		interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&B53_0>, <&B53_1>;
+	};
+
+	clocks: clocks {
+		periph_clk:periph-clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <200000000>;
+		};
+	};
+
+	psci {
+		compatible = "arm,psci-0.2";
+		method = "smc";
+	};
+
+	axi@81000000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x0 0x81000000 0x8000>;
+
+		gic: interrupt-controller@1000 {
+			compatible = "arm,gic-400";
+			#interrupt-cells = <3>;
+			interrupt-controller;
+			reg = <0x1000 0x1000>, /* GICD */
+				<0x2000 0x2000>, /* GICC */
+				<0x4000 0x2000>, /* GICH */
+				<0x6000 0x2000>; /* GICV */
+			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(2) |
+					IRQ_TYPE_LEVEL_HIGH)>;
+		};
+	};
+
+	bus@ff800000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x0 0xff800000 0x800000>;
+
+		uart0: serial@640 {
+			compatible = "brcm,bcm6345-uart";
+			reg = <0x640 0x18>;
+			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&periph_clk>;
+			clock-names = "refclk";
+			status = "disabled";
+		};
+	};
+};
diff --git a/arch/arm64/boot/dts/broadcom/bcmbca/bcm6858.dtsi b/arch/arm64/boot/dts/broadcom/bcmbca/bcm6858.dtsi
new file mode 100644
index 000000000000..29a880c6c858
--- /dev/null
+++ b/arch/arm64/boot/dts/broadcom/bcmbca/bcm6858.dtsi
@@ -0,0 +1,121 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2022 Broadcom Ltd.
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+	compatible = "brcm,bcm6858", "brcm,bcmbca";
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	interrupt-parent = <&gic>;
+
+	cpus {
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		B53_0: cpu@0 {
+			compatible = "brcm,brahma-b53";
+			device_type = "cpu";
+			reg = <0x0 0x0>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		B53_1: cpu@1 {
+			compatible = "brcm,brahma-b53";
+			device_type = "cpu";
+			reg = <0x0 0x1>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		B53_2: cpu@2 {
+			compatible = "brcm,brahma-b53";
+			device_type = "cpu";
+			reg = <0x0 0x2>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+
+		B53_3: cpu@3 {
+			compatible = "brcm,brahma-b53";
+			device_type = "cpu";
+			reg = <0x0 0x3>;
+			next-level-cache = <&L2_0>;
+			enable-method = "psci";
+		};
+		L2_0: l2-cache0 {
+			compatible = "cache";
+		};
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			<GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+	};
+
+	pmu: pmu {
+		compatible = "arm,armv8-pmuv3";
+		interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
+			<GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&B53_0>, <&B53_1>,
+			<&B53_2>, <&B53_3>;
+	};
+
+	clocks: clocks {
+		periph_clk:periph-clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <200000000>;
+		};
+	};
+
+	psci {
+		compatible = "arm,psci-0.2";
+		method = "smc";
+	};
+
+	axi@81000000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x0 0x81000000 0x8000>;
+
+		gic: interrupt-controller@1000 {
+			compatible = "arm,gic-400";
+			#interrupt-cells = <3>;
+			interrupt-controller;
+			reg = <0x1000 0x1000>, /* GICD */
+				<0x2000 0x2000>, /* GICC */
+				<0x4000 0x2000>, /* GICH */
+				<0x6000 0x2000>; /* GICV */
+			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) |
+					IRQ_TYPE_LEVEL_HIGH)>;
+		};
+	};
+
+	bus@ff800000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x0 0xff800000 0x62000>;
+
+		uart0: serial@640 {
+			compatible = "brcm,bcm6345-uart";
+			reg = <0x640 0x18>;
+			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&periph_clk>;
+			clock-names = "refclk";
+			status = "disabled";
+		};
+	};
+};
diff --git a/arch/arm64/boot/dts/broadcom/bcmbca/bcm94908.dts b/arch/arm64/boot/dts/broadcom/bcmbca/bcm94908.dts
new file mode 100644
index 000000000000..fcbd3c430ace
--- /dev/null
+++ b/arch/arm64/boot/dts/broadcom/bcmbca/bcm94908.dts
@@ -0,0 +1,30 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2022 Broadcom Ltd.
+ */
+
+/dts-v1/;
+
+#include "bcm4908.dtsi"
+
+/ {
+	model = "Broadcom BCM94908 Reference Board";
+	compatible = "brcm,bcm94908", "brcm,bcm4908", "brcm,bcmbca";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x08000000>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/broadcom/bcmbca/bcm94912.dts b/arch/arm64/boot/dts/broadcom/bcmbca/bcm94912.dts
new file mode 100644
index 000000000000..a3623e6f6919
--- /dev/null
+++ b/arch/arm64/boot/dts/broadcom/bcmbca/bcm94912.dts
@@ -0,0 +1,30 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2022 Broadcom Ltd.
+ */
+
+/dts-v1/;
+
+#include "bcm4912.dtsi"
+
+/ {
+	model = "Broadcom BCM94912 Reference Board";
+	compatible = "brcm,bcm94912", "brcm,bcm4912", "brcm,bcmbca";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x08000000>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/broadcom/bcmbca/bcm963146.dts b/arch/arm64/boot/dts/broadcom/bcmbca/bcm963146.dts
new file mode 100644
index 000000000000..e39f1e6d4774
--- /dev/null
+++ b/arch/arm64/boot/dts/broadcom/bcmbca/bcm963146.dts
@@ -0,0 +1,30 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2022 Broadcom Ltd.
+ */
+
+/dts-v1/;
+
+#include "bcm63146.dtsi"
+
+/ {
+	model = "Broadcom BCM963146 Reference Board";
+	compatible = "brcm,bcm963146", "brcm,bcm63146", "brcm,bcmbca";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x08000000>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/broadcom/bcmbca/bcm963158.dts b/arch/arm64/boot/dts/broadcom/bcmbca/bcm963158.dts
new file mode 100644
index 000000000000..eba07e0b1ca6
--- /dev/null
+++ b/arch/arm64/boot/dts/broadcom/bcmbca/bcm963158.dts
@@ -0,0 +1,30 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2022 Broadcom Ltd.
+ */
+
+/dts-v1/;
+
+#include "bcm63158.dtsi"
+
+/ {
+	model = "Broadcom BCM963158 Reference Board";
+	compatible = "brcm,bcm963158", "brcm,bcm63158", "brcm,bcmbca";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x08000000>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/broadcom/bcmbca/bcm96813.dts b/arch/arm64/boot/dts/broadcom/bcmbca/bcm96813.dts
new file mode 100644
index 000000000000..af17091ae764
--- /dev/null
+++ b/arch/arm64/boot/dts/broadcom/bcmbca/bcm96813.dts
@@ -0,0 +1,30 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2022 Broadcom Ltd.
+ */
+
+/dts-v1/;
+
+#include "bcm6813.dtsi"
+
+/ {
+	model = "Broadcom BCM96813 Reference Board";
+	compatible = "brcm,bcm96813", "brcm,bcm6813", "brcm,bcmbca";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x08000000>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/broadcom/bcmbca/bcm96856.dts b/arch/arm64/boot/dts/broadcom/bcmbca/bcm96856.dts
new file mode 100644
index 000000000000..032aeb75c983
--- /dev/null
+++ b/arch/arm64/boot/dts/broadcom/bcmbca/bcm96856.dts
@@ -0,0 +1,30 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2022 Broadcom Ltd.
+ */
+
+/dts-v1/;
+
+#include "bcm6856.dtsi"
+
+/ {
+	model = "Broadcom BCM96856 Reference Board";
+	compatible = "brcm,bcm96856", "brcm,bcm6856", "brcm,bcmbca";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x08000000>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/broadcom/bcmbca/bcm96858.dts b/arch/arm64/boot/dts/broadcom/bcmbca/bcm96858.dts
new file mode 100644
index 000000000000..0cbf582f5d54
--- /dev/null
+++ b/arch/arm64/boot/dts/broadcom/bcmbca/bcm96858.dts
@@ -0,0 +1,30 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2022 Broadcom Ltd.
+ */
+
+/dts-v1/;
+
+#include "bcm6858.dtsi"
+
+/ {
+	model = "Broadcom BCM96858 Reference Board";
+	compatible = "brcm,bcm96858", "brcm,bcm6858", "brcm,bcmbca";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x08000000>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/broadcom/northstar2/ns2-svk.dts b/arch/arm64/boot/dts/broadcom/northstar2/ns2-svk.dts
index ec19fbf928a1..e34172e3117e 100644
--- a/arch/arm64/boot/dts/broadcom/northstar2/ns2-svk.dts
+++ b/arch/arm64/boot/dts/broadcom/northstar2/ns2-svk.dts
@@ -111,8 +111,8 @@
 		compatible = "silabs,si3226x";
 		reg = <0>;
 		spi-max-frequency = <5000000>;
-		spi-cpha = <1>;
-		spi-cpol = <1>;
+		spi-cpha;
+		spi-cpol;
 		pl022,hierarchy = <0>;
 		pl022,interface = <0>;
 		pl022,slave-tx-disable = <0>;
@@ -135,8 +135,8 @@
 		at25,byte-len = <0x8000>;
 		at25,addr-mode = <2>;
 		at25,page-size = <64>;
-		spi-cpha = <1>;
-		spi-cpol = <1>;
+		spi-cpha;
+		spi-cpol;
 		pl022,hierarchy = <0>;
 		pl022,interface = <0>;
 		pl022,slave-tx-disable = <0>;
@@ -203,7 +203,7 @@
 
 &qspi {
 	bspi-sel = <0>;
-	flash: m25p80@0 {
+	flash: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "m25p80";
diff --git a/arch/arm64/boot/dts/broadcom/northstar2/ns2-xmc.dts b/arch/arm64/boot/dts/broadcom/northstar2/ns2-xmc.dts
index f00c21e0767e..7bf26f3e36bf 100644
--- a/arch/arm64/boot/dts/broadcom/northstar2/ns2-xmc.dts
+++ b/arch/arm64/boot/dts/broadcom/northstar2/ns2-xmc.dts
@@ -146,7 +146,7 @@
 };
 
 &qspi {
-	flash: m25p80@0 {
+	flash: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "m25p80";
diff --git a/arch/arm64/boot/dts/broadcom/northstar2/ns2.dtsi b/arch/arm64/boot/dts/broadcom/northstar2/ns2.dtsi
index 2cfeaf3b0a87..fda97c47f4e9 100644
--- a/arch/arm64/boot/dts/broadcom/northstar2/ns2.dtsi
+++ b/arch/arm64/boot/dts/broadcom/northstar2/ns2.dtsi
@@ -276,7 +276,7 @@
 			mboxes = <&pdc3 0>;
 		};
 
-		dma0: dma@61360000 {
+		dma0: dma-controller@61360000 {
 			compatible = "arm,pl330", "arm,primecell";
 			reg = <0x61360000 0x1000>;
 			interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>,
@@ -289,8 +289,6 @@
 				     <GIC_SPI 215 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 216 IRQ_TYPE_LEVEL_HIGH>;
 			#dma-cells = <1>;
-			#dma-channels = <8>;
-			#dma-requests = <32>;
 			clocks = <&iprocslow>;
 			clock-names = "apb_pclk";
 		};
@@ -644,7 +642,7 @@
 			reg = <0x66180000 0x1000>;
 			interrupts = <GIC_SPI 404 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&iprocslow>, <&iprocslow>;
-			clock-names = "spiclk", "apb_pclk";
+			clock-names = "sspclk", "apb_pclk";
 			#address-cells = <1>;
 			#size-cells = <0>;
 			status = "disabled";
@@ -655,7 +653,7 @@
 			reg = <0x66190000 0x1000>;
 			interrupts = <GIC_SPI 405 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&iprocslow>, <&iprocslow>;
-			clock-names = "spiclk", "apb_pclk";
+			clock-names = "sspclk", "apb_pclk";
 			#address-cells = <1>;
 			#size-cells = <0>;
 			status = "disabled";
@@ -687,7 +685,7 @@
 			};
 		};
 
-		sata: ahci@663f2000 {
+		sata: sata@663f2000 {
 			compatible = "brcm,iproc-ahci", "generic-ahci";
 			reg = <0x663f2000 0x1000>;
 			dma-coherent;
diff --git a/arch/arm64/boot/dts/broadcom/stingray/bcm958742k.dts b/arch/arm64/boot/dts/broadcom/stingray/bcm958742k.dts
index 77efa28c4dd5..dfac910a45d6 100644
--- a/arch/arm64/boot/dts/broadcom/stingray/bcm958742k.dts
+++ b/arch/arm64/boot/dts/broadcom/stingray/bcm958742k.dts
@@ -61,7 +61,7 @@
 	cs-gpios = <&gpio_hsls 34 0>;
 	status = "okay";
 
-	spi-flash@0 {
+	flash@0 {
 		compatible = "jedec,spi-nor";
 		reg = <0>;
 		spi-max-frequency = <20000000>;
@@ -76,7 +76,7 @@
 	cs-gpios = <&gpio_hsls 96 0>;
 	status = "okay";
 
-	spi-flash@0 {
+	flash@0 {
 		compatible = "jedec,spi-nor";
 		reg = <0>;
 		spi-max-frequency = <20000000>;
diff --git a/arch/arm64/boot/dts/broadcom/stingray/stingray.dtsi b/arch/arm64/boot/dts/broadcom/stingray/stingray.dtsi
index 7b04dfe67bef..8f8c25e51194 100644
--- a/arch/arm64/boot/dts/broadcom/stingray/stingray.dtsi
+++ b/arch/arm64/boot/dts/broadcom/stingray/stingray.dtsi
@@ -519,7 +519,7 @@
 			reg = <0x00180000 0x1000>;
 			interrupts = <GIC_SPI 187 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&hsls_div2_clk>, <&hsls_div2_clk>;
-			clock-names = "spiclk", "apb_pclk";
+			clock-names = "sspclk", "apb_pclk";
 			num-cs = <1>;
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -531,7 +531,7 @@
 			reg = <0x00190000 0x1000>;
 			interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&hsls_div2_clk>, <&hsls_div2_clk>;
-			clock-names = "spiclk", "apb_pclk";
+			clock-names = "sspclk", "apb_pclk";
 			num-cs = <1>;
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -543,7 +543,7 @@
 			reg = <0x00220000 0x28>;
 		};
 
-		dma0: dma@310000 {
+		dma0: dma-controller@310000 {
 			compatible = "arm,pl330", "arm,primecell";
 			reg = <0x00310000 0x1000>;
 			interrupts = <GIC_SPI 193 IRQ_TYPE_LEVEL_HIGH>,
@@ -556,8 +556,6 @@
 				     <GIC_SPI 200 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 201 IRQ_TYPE_LEVEL_HIGH>;
 			#dma-cells = <1>;
-			#dma-channels = <8>;
-			#dma-requests = <32>;
 			clocks = <&hsls_div2_clk>;
 			clock-names = "apb_pclk";
 			iommus = <&smmu 0x6000 0x0000>;
@@ -569,7 +567,7 @@
 			reg-names = "amac_base";
 			dma-coherent;
 			interrupts = <GIC_SPI 213 IRQ_TYPE_LEVEL_HIGH>;
-			status= "disabled";
+			status = "disabled";
 		};
 
 		nand: nand@360000 {
diff --git a/arch/arm64/boot/dts/exynos/Makefile b/arch/arm64/boot/dts/exynos/Makefile
index b41e86df0a84..6e4ba69268e5 100644
--- a/arch/arm64/boot/dts/exynos/Makefile
+++ b/arch/arm64/boot/dts/exynos/Makefile
@@ -1,6 +1,8 @@
 # SPDX-License-Identifier: GPL-2.0
 dtb-$(CONFIG_ARCH_EXYNOS) += \
-	exynos5433-tm2.dtb	\
-	exynos5433-tm2e.dtb	\
-	exynos7-espresso.dtb	\
+	exynos5433-tm2.dtb		\
+	exynos5433-tm2e.dtb		\
+	exynos7-espresso.dtb		\
+	exynos7885-jackpotlte.dtb	\
+	exynos850-e850-96.dtb		\
 	exynosautov9-sadk.dtb
diff --git a/arch/arm64/boot/dts/exynos/exynos-pinctrl.h b/arch/arm64/boot/dts/exynos/exynos-pinctrl.h
new file mode 100644
index 000000000000..7dd94a9b3652
--- /dev/null
+++ b/arch/arm64/boot/dts/exynos/exynos-pinctrl.h
@@ -0,0 +1,79 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Samsung Exynos DTS pinctrl constants
+ *
+ * Copyright (c) 2016 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
+ * Copyright (c) 2022 Linaro Ltd
+ * Author: Krzysztof Kozlowski <krzk@kernel.org>
+ */
+
+#ifndef __DTS_ARM64_SAMSUNG_EXYNOS_PINCTRL_H__
+#define __DTS_ARM64_SAMSUNG_EXYNOS_PINCTRL_H__
+
+#define EXYNOS_PIN_PULL_NONE		0
+#define EXYNOS_PIN_PULL_DOWN		1
+#define EXYNOS_PIN_PULL_UP		3
+
+/* Pin function in power down mode */
+#define EXYNOS_PIN_PDN_OUT0		0
+#define EXYNOS_PIN_PDN_OUT1		1
+#define EXYNOS_PIN_PDN_INPUT		2
+#define EXYNOS_PIN_PDN_PREV		3
+
+/*
+ * Drive strengths for Exynos5410, Exynos542x, Exynos5800, Exynos7885, Exynos850
+ * (except GPIO_HSI block), ExynosAutov9 (FSI0, PERIC1)
+ */
+#define EXYNOS5420_PIN_DRV_LV1		0
+#define EXYNOS5420_PIN_DRV_LV2		1
+#define EXYNOS5420_PIN_DRV_LV3		2
+#define EXYNOS5420_PIN_DRV_LV4		3
+
+/* Drive strengths for Exynos5433 */
+#define EXYNOS5433_PIN_DRV_FAST_SR1	0
+#define EXYNOS5433_PIN_DRV_FAST_SR2	1
+#define EXYNOS5433_PIN_DRV_FAST_SR3	2
+#define EXYNOS5433_PIN_DRV_FAST_SR4	3
+#define EXYNOS5433_PIN_DRV_FAST_SR5	4
+#define EXYNOS5433_PIN_DRV_FAST_SR6	5
+#define EXYNOS5433_PIN_DRV_SLOW_SR1	8
+#define EXYNOS5433_PIN_DRV_SLOW_SR2	9
+#define EXYNOS5433_PIN_DRV_SLOW_SR3	0xa
+#define EXYNOS5433_PIN_DRV_SLOW_SR4	0xb
+#define EXYNOS5433_PIN_DRV_SLOW_SR5	0xc
+#define EXYNOS5433_PIN_DRV_SLOW_SR6	0xf
+
+/* Drive strengths for Exynos7 (except FSYS1) */
+#define EXYNOS7_PIN_DRV_LV1		0
+#define EXYNOS7_PIN_DRV_LV2		2
+#define EXYNOS7_PIN_DRV_LV3		1
+#define EXYNOS7_PIN_DRV_LV4		3
+
+/* Drive strengths for Exynos7 FSYS1 block */
+#define EXYNOS7_FSYS1_PIN_DRV_LV1	0
+#define EXYNOS7_FSYS1_PIN_DRV_LV2	4
+#define EXYNOS7_FSYS1_PIN_DRV_LV3	2
+#define EXYNOS7_FSYS1_PIN_DRV_LV4	6
+#define EXYNOS7_FSYS1_PIN_DRV_LV5	1
+#define EXYNOS7_FSYS1_PIN_DRV_LV6	5
+
+/* Drive strengths for Exynos850 GPIO_HSI block */
+#define EXYNOS850_HSI_PIN_DRV_LV1	0	/* 1x   */
+#define EXYNOS850_HSI_PIN_DRV_LV1_5	1	/* 1.5x */
+#define EXYNOS850_HSI_PIN_DRV_LV2	2	/* 2x   */
+#define EXYNOS850_HSI_PIN_DRV_LV2_5	3	/* 2.5x */
+#define EXYNOS850_HSI_PIN_DRV_LV3	4	/* 3x   */
+#define EXYNOS850_HSI_PIN_DRV_LV4	5	/* 4x   */
+
+#define EXYNOS_PIN_FUNC_INPUT		0
+#define EXYNOS_PIN_FUNC_OUTPUT		1
+#define EXYNOS_PIN_FUNC_2		2
+#define EXYNOS_PIN_FUNC_3		3
+#define EXYNOS_PIN_FUNC_4		4
+#define EXYNOS_PIN_FUNC_5		5
+#define EXYNOS_PIN_FUNC_6		6
+#define EXYNOS_PIN_FUNC_EINT		0xf
+#define EXYNOS_PIN_FUNC_F		EXYNOS_PIN_FUNC_EINT
+
+#endif /* __DTS_ARM64_SAMSUNG_EXYNOS_PINCTRL_H__ */
diff --git a/arch/arm64/boot/dts/exynos/exynos5433-pinctrl.dtsi b/arch/arm64/boot/dts/exynos/exynos5433-pinctrl.dtsi
index 32a6518517e5..681553577ebc 100644
--- a/arch/arm64/boot/dts/exynos/exynos5433-pinctrl.dtsi
+++ b/arch/arm64/boot/dts/exynos/exynos5433-pinctrl.dtsi
@@ -9,18 +9,27 @@
  * tree nodes are listed in this file.
  */
 
-#include <dt-bindings/pinctrl/samsung.h>
+#include "exynos-pinctrl.h"
 
-#define PIN(_func, _pin, _pull, _drv)					\
-	_pin {								\
+#define PIN(_pin, _func, _pull, _drv)					\
+	pin- ## _pin {							\
 		samsung,pins = #_pin;					\
 		samsung,pin-function = <EXYNOS_PIN_FUNC_ ##_func>;	\
 		samsung,pin-pud = <EXYNOS_PIN_PULL_ ##_pull>;		\
 		samsung,pin-drv = <EXYNOS5433_PIN_DRV_ ##_drv>;		\
 	}
 
+#define PIN_IN(_pin, _pull, _drv)					\
+	PIN(_pin, INPUT, _pull, _drv)
+
+#define PIN_OT(_pin, _pull, _drv)					\
+	PIN(_pin, OUTPUT, _pull, _drv)
+
+#define PIN_F2(_pin, _pull, _drv)					\
+	PIN(_pin, 2, _pull, _drv)
+
 &pinctrl_alive {
-	gpa0: gpa0 {
+	gpa0: gpa0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -37,7 +46,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpa1: gpa1 {
+	gpa1: gpa1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -54,7 +63,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpa2: gpa2 {
+	gpa2: gpa2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -62,7 +71,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpa3: gpa3 {
+	gpa3: gpa3-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -70,7 +79,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpf1: gpf1 {
+	gpf1: gpf1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -78,7 +87,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpf2: gpf2 {
+	gpf2: gpf2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -86,7 +95,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpf3: gpf3 {
+	gpf3: gpf3-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -94,7 +103,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpf4: gpf4 {
+	gpf4: gpf4-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -102,7 +111,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpf5: gpf5 {
+	gpf5: gpf5-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -112,7 +121,7 @@
 };
 
 &pinctrl_aud {
-	gpz0: gpz0 {
+	gpz0: gpz0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -120,7 +129,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpz1: gpz1 {
+	gpz1: gpz1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -128,7 +137,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	i2s0_bus: i2s0-bus {
+	i2s0_bus: i2s0-bus-pins {
 		samsung,pins = "gpz0-0", "gpz0-1", "gpz0-2", "gpz0-3",
 				"gpz0-4", "gpz0-5", "gpz0-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
@@ -136,14 +145,14 @@
 		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR1>;
 	};
 
-	pcm0_bus: pcm0-bus {
+	pcm0_bus: pcm0-bus-pins {
 		samsung,pins = "gpz1-0", "gpz1-1", "gpz1-2", "gpz1-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR1>;
 	};
 
-	uart_aud_bus: uart-aud-bus {
+	uart_aud_bus: uart-aud-bus-pins {
 		samsung,pins = "gpz1-3", "gpz1-2", "gpz1-1", "gpz1-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
@@ -152,7 +161,7 @@
 };
 
 &pinctrl_cpif {
-	gpv6: gpv6 {
+	gpv6: gpv6-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -162,7 +171,7 @@
 };
 
 &pinctrl_ese {
-	gpj2: gpj2 {
+	gpj2: gpj2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -172,7 +181,7 @@
 };
 
 &pinctrl_finger {
-	gpd5: gpd5 {
+	gpd5: gpd5-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -180,14 +189,14 @@
 		#interrupt-cells = <2>;
 	};
 
-	spi2_bus: spi2-bus {
+	spi2_bus: spi2-bus-pins {
 		samsung,pins = "gpd5-0", "gpd5-2", "gpd5-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR1>;
 	};
 
-	hs_i2c6_bus: hs-i2c6-bus {
+	hs_i2c6_bus: hs-i2c6-bus-pins {
 		samsung,pins = "gpd5-3", "gpd5-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
@@ -196,7 +205,7 @@
 };
 
 &pinctrl_fsys {
-	gph1: gph1 {
+	gph1: gph1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -204,7 +213,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpr4: gpr4 {
+	gpr4: gpr4-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -212,7 +221,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpr0: gpr0 {
+	gpr0: gpr0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -220,7 +229,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpr1: gpr1 {
+	gpr1: gpr1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -228,7 +237,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpr2: gpr2 {
+	gpr2: gpr2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -236,7 +245,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpr3: gpr3 {
+	gpr3: gpr3-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -244,139 +253,139 @@
 		#interrupt-cells = <2>;
 	};
 
-	sd0_clk: sd0-clk {
+	sd0_clk: sd0-clk-pins {
 		samsung,pins = "gpr0-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR4>;
 	};
 
-	sd0_cmd: sd0-cmd {
+	sd0_cmd: sd0-cmd-pins {
 		samsung,pins = "gpr0-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR4>;
 	};
 
-	sd0_rdqs: sd0-rdqs {
+	sd0_rdqs: sd0-rdqs-pins {
 		samsung,pins = "gpr0-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
 		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR4>;
 	};
 
-	sd0_qrdy: sd0-qrdy {
+	sd0_qrdy: sd0-qrdy-pins {
 		samsung,pins = "gpr0-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
 		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR4>;
 	};
 
-	sd0_bus1: sd0-bus-width1 {
+	sd0_bus1: sd0-bus-width1-pins {
 		samsung,pins = "gpr1-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR4>;
 	};
 
-	sd0_bus4: sd0-bus-width4 {
+	sd0_bus4: sd0-bus-width4-pins {
 		samsung,pins = "gpr1-1", "gpr1-2", "gpr1-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR4>;
 	};
 
-	sd0_bus8: sd0-bus-width8 {
+	sd0_bus8: sd0-bus-width8-pins {
 		samsung,pins = "gpr1-4", "gpr1-5", "gpr1-6", "gpr1-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR4>;
 	};
 
-	sd1_clk: sd1-clk {
+	sd1_clk: sd1-clk-pins {
 		samsung,pins = "gpr2-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR4>;
 	};
 
-	sd1_cmd: sd1-cmd {
+	sd1_cmd: sd1-cmd-pins {
 		samsung,pins = "gpr2-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR4>;
 	};
 
-	sd1_bus1: sd1-bus-width1 {
+	sd1_bus1: sd1-bus-width1-pins {
 		samsung,pins = "gpr3-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR4>;
 	};
 
-	sd1_bus4: sd1-bus-width4 {
+	sd1_bus4: sd1-bus-width4-pins {
 		samsung,pins = "gpr3-1", "gpr3-2", "gpr3-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR4>;
 	};
 
-	sd1_bus8: sd1-bus-width8 {
+	sd1_bus8: sd1-bus-width8-pins {
 		samsung,pins = "gpr3-4", "gpr3-5", "gpr3-6", "gpr3-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR4>;
 	};
 
-	pcie_bus: pcie_bus {
+	pcie_bus: pcie-bus-pins {
 		samsung,pins = "gpr3-4", "gpr3-5", "gpr3-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 	};
 
-	sd2_clk: sd2-clk {
+	sd2_clk: sd2-clk-pins {
 		samsung,pins = "gpr4-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR4>;
 	};
 
-	sd2_cmd: sd2-cmd {
+	sd2_cmd: sd2-cmd-pins {
 		samsung,pins = "gpr4-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR4>;
 	};
 
-	sd2_cd: sd2-cd {
+	sd2_cd: sd2-cd-pins {
 		samsung,pins = "gpr4-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR4>;
 	};
 
-	sd2_bus1: sd2-bus-width1 {
+	sd2_bus1: sd2-bus-width1-pins {
 		samsung,pins = "gpr4-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR4>;
 	};
 
-	sd2_bus4: sd2-bus-width4 {
+	sd2_bus4: sd2-bus-width4-pins {
 		samsung,pins = "gpr4-4", "gpr4-5", "gpr4-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR4>;
 	};
 
-	sd2_clk_output: sd2-clk-output {
+	sd2_clk_output: sd2-clk-output-pins {
 		samsung,pins = "gpr4-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR3>;
 	};
 
-	sd2_cmd_output: sd2-cmd-output {
+	sd2_cmd_output: sd2-cmd-output-pins {
 		samsung,pins = "gpr4-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
@@ -385,7 +394,7 @@
 };
 
 &pinctrl_imem {
-	gpf0: gpf0 {
+	gpf0: gpf0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -395,7 +404,7 @@
 };
 
 &pinctrl_nfc {
-	gpj0: gpj0 {
+	gpj0: gpj0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -403,7 +412,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	hs_i2c4_bus: hs-i2c4-bus {
+	hs_i2c4_bus: hs-i2c4-bus-pins {
 		samsung,pins = "gpj0-1", "gpj0-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
@@ -412,7 +421,7 @@
 };
 
 &pinctrl_peric {
-	gpv7: gpv7 {
+	gpv7: gpv7-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -420,7 +429,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpb0: gpb0 {
+	gpb0: gpb0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -428,7 +437,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpc0: gpc0 {
+	gpc0: gpc0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -436,7 +445,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpc1: gpc1 {
+	gpc1: gpc1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -444,7 +453,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpc2: gpc2 {
+	gpc2: gpc2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -452,7 +461,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpc3: gpc3 {
+	gpc3: gpc3-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -460,7 +469,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpg0: gpg0 {
+	gpg0: gpg0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -468,7 +477,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpd0: gpd0 {
+	gpd0: gpd0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -476,7 +485,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpd1: gpd1 {
+	gpd1: gpd1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -484,7 +493,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpd2: gpd2 {
+	gpd2: gpd2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -492,7 +501,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpd4: gpd4 {
+	gpd4: gpd4-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -500,7 +509,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpd8: gpd8 {
+	gpd8: gpd8-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -508,7 +517,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpd6: gpd6 {
+	gpd6: gpd6-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -516,7 +525,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpd7: gpd7 {
+	gpd7: gpd7-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -524,7 +533,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpg1: gpg1 {
+	gpg1: gpg1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -532,7 +541,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpg2: gpg2 {
+	gpg2: gpg2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -540,7 +549,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpg3: gpg3 {
+	gpg3: gpg3-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -548,21 +557,21 @@
 		#interrupt-cells = <2>;
 	};
 
-	hs_i2c8_bus: hs-i2c8-bus {
+	hs_i2c8_bus: hs-i2c8-bus-pins {
 		samsung,pins = "gpb0-1", "gpb0-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR1>;
 	};
 
-	hs_i2c9_bus: hs-i2c9-bus {
+	hs_i2c9_bus: hs-i2c9-bus-pins {
 		samsung,pins = "gpb0-3", "gpb0-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR1>;
 	};
 
-	i2s1_bus: i2s1-bus {
+	i2s1_bus: i2s1-bus-pins {
 		samsung,pins = "gpd4-0", "gpd4-1", "gpd4-2",
 				"gpd4-3", "gpd4-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
@@ -570,7 +579,7 @@
 		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR1>;
 	};
 
-	pcm1_bus: pcm1-bus {
+	pcm1_bus: pcm1-bus-pins {
 		samsung,pins = "gpd4-0", "gpd4-1", "gpd4-2",
 				"gpd4-3", "gpd4-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
@@ -578,193 +587,193 @@
 		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR1>;
 	};
 
-	spdif_bus: spdif-bus {
+	spdif_bus: spdif-bus-pins {
 		samsung,pins = "gpd4-3", "gpd4-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR1>;
 	};
 
-	fimc_is_spi_pin0: fimc-is-spi-pin0 {
+	fimc_is_spi_pin0: fimc-is-spi-pin0-pins {
 		samsung,pins = "gpc3-3", "gpc3-2", "gpc3-1", "gpc3-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR1>;
 	};
 
-	fimc_is_spi_pin1: fimc-is-spi-pin1 {
+	fimc_is_spi_pin1: fimc-is-spi-pin1-pins {
 		samsung,pins = "gpc3-7", "gpc3-6", "gpc3-5", "gpc3-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR1>;
 	};
 
-	uart0_bus: uart0-bus {
+	uart0_bus: uart0-bus-pins {
 		samsung,pins = "gpd0-3", "gpd0-2", "gpd0-1", "gpd0-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 	};
 
-	hs_i2c2_bus: hs-i2c2-bus {
+	hs_i2c2_bus: hs-i2c2-bus-pins {
 		samsung,pins = "gpd0-3", "gpd0-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR1>;
 	};
 
-	uart2_bus: uart2-bus {
+	uart2_bus: uart2-bus-pins {
 		samsung,pins = "gpd1-5", "gpd1-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 	};
 
-	uart1_bus: uart1-bus {
+	uart1_bus: uart1-bus-pins {
 		samsung,pins = "gpd1-3", "gpd1-2", "gpd1-1", "gpd1-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 	};
 
-	hs_i2c3_bus: hs-i2c3-bus {
+	hs_i2c3_bus: hs-i2c3-bus-pins {
 		samsung,pins = "gpd1-3", "gpd1-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR1>;
 	};
 
-	hs_i2c0_bus: hs-i2c0-bus {
+	hs_i2c0_bus: hs-i2c0-bus-pins {
 		samsung,pins = "gpd2-1", "gpd2-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR1>;
 	};
 
-	hs_i2c1_bus: hs-i2c1-bus {
+	hs_i2c1_bus: hs-i2c1-bus-pins {
 		samsung,pins = "gpd2-3", "gpd2-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR1>;
 	};
 
-	pwm0_out: pwm0-out {
+	pwm0_out: pwm0-out-pins {
 		samsung,pins = "gpd2-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR1>;
 	};
 
-	pwm1_out: pwm1-out {
+	pwm1_out: pwm1-out-pins {
 		samsung,pins = "gpd2-5";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR1>;
 	};
 
-	pwm2_out: pwm2-out {
+	pwm2_out: pwm2-out-pins {
 		samsung,pins = "gpd2-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR1>;
 	};
 
-	pwm3_out: pwm3-out {
+	pwm3_out: pwm3-out-pins {
 		samsung,pins = "gpd2-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR1>;
 	};
 
-	spi1_bus: spi1-bus {
+	spi1_bus: spi1-bus-pins {
 		samsung,pins = "gpd6-2", "gpd6-4", "gpd6-5";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR1>;
 	};
 
-	hs_i2c7_bus: hs-i2c7-bus {
+	hs_i2c7_bus: hs-i2c7-bus-pins {
 		samsung,pins = "gpd2-7", "gpd2-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR1>;
 	};
 
-	spi0_bus: spi0-bus {
+	spi0_bus: spi0-bus-pins {
 		samsung,pins = "gpd8-0", "gpd6-0", "gpd6-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR1>;
 	};
 
-	hs_i2c10_bus: hs-i2c10-bus {
+	hs_i2c10_bus: hs-i2c10-bus-pins {
 		samsung,pins = "gpg3-1", "gpg3-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR1>;
 	};
 
-	hs_i2c11_bus: hs-i2c11-bus {
+	hs_i2c11_bus: hs-i2c11-bus-pins {
 		samsung,pins = "gpg3-3", "gpg3-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR1>;
 	};
 
-	spi3_bus: spi3-bus {
+	spi3_bus: spi3-bus-pins {
 		samsung,pins = "gpg3-4", "gpg3-6", "gpg3-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR1>;
 	};
 
-	spi4_bus: spi4-bus {
+	spi4_bus: spi4-bus-pins {
 		samsung,pins = "gpv7-1", "gpv7-3", "gpv7-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR1>;
 	};
 
-	fimc_is_uart: fimc-is-uart {
+	fimc_is_uart: fimc-is-uart-pins {
 		samsung,pins = "gpc1-1", "gpc0-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR1>;
 	};
 
-	fimc_is_ch0_i2c: fimc-is-ch0_i2c {
+	fimc_is_ch0_i2c: fimc-is-ch0-i2c-pins {
 		samsung,pins = "gpc2-1", "gpc2-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR1>;
 	};
 
-	fimc_is_ch0_mclk: fimc-is-ch0_mclk {
+	fimc_is_ch0_mclk: fimc-is-ch0-mclk-pins {
 		samsung,pins = "gpd7-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR1>;
 	};
 
-	fimc_is_ch1_i2c: fimc-is-ch1-i2c {
+	fimc_is_ch1_i2c: fimc-is-ch1-i2c-pins {
 		samsung,pins = "gpc2-3", "gpc2-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR1>;
 	};
 
-	fimc_is_ch1_mclk: fimc-is-ch1-mclk {
+	fimc_is_ch1_mclk: fimc-is-ch1-mclk-pins {
 		samsung,pins = "gpd7-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR1>;
 	};
 
-	fimc_is_ch2_i2c: fimc-is-ch2-i2c {
+	fimc_is_ch2_i2c: fimc-is-ch2-i2c-pins {
 		samsung,pins = "gpc2-5", "gpc2-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR1>;
 	};
 
-	fimc_is_ch2_mclk: fimc-is-ch2-mclk {
+	fimc_is_ch2_mclk: fimc-is-ch2-mclk-pins {
 		samsung,pins = "gpd7-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
@@ -773,7 +782,7 @@
 };
 
 &pinctrl_touch {
-	gpj1: gpj1 {
+	gpj1: gpj1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -781,7 +790,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	hs_i2c5_bus: hs-i2c5-bus {
+	hs_i2c5_bus: hs-i2c5-bus-pins {
 		samsung,pins = "gpj1-1", "gpj1-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_4>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
diff --git a/arch/arm64/boot/dts/exynos/exynos5433-tm2-common.dtsi b/arch/arm64/boot/dts/exynos/exynos5433-tm2-common.dtsi
index cbcc01a66aab..bde6a6bb8dfc 100644
--- a/arch/arm64/boot/dts/exynos/exynos5433-tm2-common.dtsi
+++ b/arch/arm64/boot/dts/exynos/exynos5433-tm2-common.dtsi
@@ -795,7 +795,7 @@
 		reg = <0x27>;
 		interrupt-parent = <&gpa1>;
 		interrupts = <3 IRQ_TYPE_EDGE_RISING>;
-		en-gpios = <&gpf1 4 GPIO_ACTIVE_HIGH>;
+		en-gpios = <&gpf1 4 GPIO_ACTIVE_LOW>;
 		wake-gpios = <&gpj0 2 GPIO_ACTIVE_HIGH>;
 	};
 };
@@ -858,10 +858,10 @@
 		interrupts = <5 IRQ_TYPE_EDGE_FALLING>;
 		reg = <0x66>;
 
-		muic: max77843-muic {
+		muic: extcon {
 			compatible = "maxim,max77843-muic";
 
-			musb_con: musb-connector {
+			musb_con: connector {
 				compatible = "samsung,usb-connector-11pin",
 					     "usb-b-connector";
 				label = "micro-USB";
@@ -871,6 +871,17 @@
 					#address-cells = <1>;
 					#size-cells = <0>;
 
+					port@0 {
+						/*
+						 * TODO: The DTS this is based on does not have
+						 * port@0 which is a required property. The ports
+						 * look incomplete and need fixing.
+						 * Add a disabled port just to satisfy dtschema.
+						 */
+						reg = <0>;
+						status = "disabled";
+					};
+
 					port@3 {
 						reg = <3>;
 						musb_con_to_mhl: endpoint {
@@ -910,7 +921,7 @@
 			};
 		};
 
-		haptic: max77843-haptic {
+		haptic: motor-driver {
 			compatible = "maxim,max77843-haptic";
 			haptic-supply = <&ldo38_reg>;
 			pwms = <&pwm 0 33670 0>;
@@ -1011,80 +1022,80 @@
 	pinctrl-0 = <&initial_alive>;
 
 	initial_alive: initial-state {
-		PIN(INPUT, gpa0-0, DOWN, FAST_SR1);
-		PIN(INPUT, gpa0-1, NONE, FAST_SR1);
-		PIN(INPUT, gpa0-2, DOWN, FAST_SR1);
-		PIN(INPUT, gpa0-3, NONE, FAST_SR1);
-		PIN(INPUT, gpa0-4, NONE, FAST_SR1);
-		PIN(INPUT, gpa0-5, DOWN, FAST_SR1);
-		PIN(INPUT, gpa0-6, NONE, FAST_SR1);
-		PIN(INPUT, gpa0-7, NONE, FAST_SR1);
-
-		PIN(INPUT, gpa1-0, UP, FAST_SR1);
-		PIN(INPUT, gpa1-1, UP, FAST_SR1);
-		PIN(INPUT, gpa1-2, NONE, FAST_SR1);
-		PIN(INPUT, gpa1-3, DOWN, FAST_SR1);
-		PIN(INPUT, gpa1-4, DOWN, FAST_SR1);
-		PIN(INPUT, gpa1-5, NONE, FAST_SR1);
-		PIN(INPUT, gpa1-6, NONE, FAST_SR1);
-		PIN(INPUT, gpa1-7, NONE, FAST_SR1);
-
-		PIN(INPUT, gpa2-0, NONE, FAST_SR1);
-		PIN(INPUT, gpa2-1, NONE, FAST_SR1);
-		PIN(INPUT, gpa2-2, NONE, FAST_SR1);
-		PIN(INPUT, gpa2-3, DOWN, FAST_SR1);
-		PIN(INPUT, gpa2-4, NONE, FAST_SR1);
-		PIN(INPUT, gpa2-5, DOWN, FAST_SR1);
-		PIN(INPUT, gpa2-6, DOWN, FAST_SR1);
-		PIN(INPUT, gpa2-7, NONE, FAST_SR1);
-
-		PIN(INPUT, gpa3-0, DOWN, FAST_SR1);
-		PIN(INPUT, gpa3-1, DOWN, FAST_SR1);
-		PIN(INPUT, gpa3-2, NONE, FAST_SR1);
-		PIN(INPUT, gpa3-3, DOWN, FAST_SR1);
-		PIN(INPUT, gpa3-4, NONE, FAST_SR1);
-		PIN(INPUT, gpa3-5, DOWN, FAST_SR1);
-		PIN(INPUT, gpa3-6, DOWN, FAST_SR1);
-		PIN(INPUT, gpa3-7, DOWN, FAST_SR1);
-
-		PIN(INPUT, gpf1-0, NONE, FAST_SR1);
-		PIN(INPUT, gpf1-1, NONE, FAST_SR1);
-		PIN(INPUT, gpf1-2, DOWN, FAST_SR1);
-		PIN(INPUT, gpf1-4, UP, FAST_SR1);
-		PIN(OUTPUT, gpf1-5, NONE, FAST_SR1);
-		PIN(INPUT, gpf1-6, DOWN, FAST_SR1);
-		PIN(INPUT, gpf1-7, DOWN, FAST_SR1);
-
-		PIN(INPUT, gpf2-0, DOWN, FAST_SR1);
-		PIN(INPUT, gpf2-1, DOWN, FAST_SR1);
-		PIN(INPUT, gpf2-2, DOWN, FAST_SR1);
-		PIN(INPUT, gpf2-3, DOWN, FAST_SR1);
-
-		PIN(INPUT, gpf3-0, DOWN, FAST_SR1);
-		PIN(INPUT, gpf3-1, DOWN, FAST_SR1);
-		PIN(INPUT, gpf3-2, NONE, FAST_SR1);
-		PIN(INPUT, gpf3-3, DOWN, FAST_SR1);
-
-		PIN(INPUT, gpf4-0, DOWN, FAST_SR1);
-		PIN(INPUT, gpf4-1, DOWN, FAST_SR1);
-		PIN(INPUT, gpf4-2, DOWN, FAST_SR1);
-		PIN(INPUT, gpf4-3, DOWN, FAST_SR1);
-		PIN(INPUT, gpf4-4, DOWN, FAST_SR1);
-		PIN(INPUT, gpf4-5, DOWN, FAST_SR1);
-		PIN(INPUT, gpf4-6, DOWN, FAST_SR1);
-		PIN(INPUT, gpf4-7, DOWN, FAST_SR1);
-
-		PIN(INPUT, gpf5-0, DOWN, FAST_SR1);
-		PIN(INPUT, gpf5-1, DOWN, FAST_SR1);
-		PIN(INPUT, gpf5-2, DOWN, FAST_SR1);
-		PIN(INPUT, gpf5-3, DOWN, FAST_SR1);
-		PIN(OUTPUT, gpf5-4, NONE, FAST_SR1);
-		PIN(INPUT, gpf5-5, DOWN, FAST_SR1);
-		PIN(INPUT, gpf5-6, DOWN, FAST_SR1);
-		PIN(INPUT, gpf5-7, DOWN, FAST_SR1);
+		PIN_IN(gpa0-0, DOWN, FAST_SR1);
+		PIN_IN(gpa0-1, NONE, FAST_SR1);
+		PIN_IN(gpa0-2, DOWN, FAST_SR1);
+		PIN_IN(gpa0-3, NONE, FAST_SR1);
+		PIN_IN(gpa0-4, NONE, FAST_SR1);
+		PIN_IN(gpa0-5, DOWN, FAST_SR1);
+		PIN_IN(gpa0-6, NONE, FAST_SR1);
+		PIN_IN(gpa0-7, NONE, FAST_SR1);
+
+		PIN_IN(gpa1-0, UP, FAST_SR1);
+		PIN_IN(gpa1-1, UP, FAST_SR1);
+		PIN_IN(gpa1-2, NONE, FAST_SR1);
+		PIN_IN(gpa1-3, DOWN, FAST_SR1);
+		PIN_IN(gpa1-4, DOWN, FAST_SR1);
+		PIN_IN(gpa1-5, NONE, FAST_SR1);
+		PIN_IN(gpa1-6, NONE, FAST_SR1);
+		PIN_IN(gpa1-7, NONE, FAST_SR1);
+
+		PIN_IN(gpa2-0, NONE, FAST_SR1);
+		PIN_IN(gpa2-1, NONE, FAST_SR1);
+		PIN_IN(gpa2-2, NONE, FAST_SR1);
+		PIN_IN(gpa2-3, DOWN, FAST_SR1);
+		PIN_IN(gpa2-4, NONE, FAST_SR1);
+		PIN_IN(gpa2-5, DOWN, FAST_SR1);
+		PIN_IN(gpa2-6, DOWN, FAST_SR1);
+		PIN_IN(gpa2-7, NONE, FAST_SR1);
+
+		PIN_IN(gpa3-0, DOWN, FAST_SR1);
+		PIN_IN(gpa3-1, DOWN, FAST_SR1);
+		PIN_IN(gpa3-2, NONE, FAST_SR1);
+		PIN_IN(gpa3-3, DOWN, FAST_SR1);
+		PIN_IN(gpa3-4, NONE, FAST_SR1);
+		PIN_IN(gpa3-5, DOWN, FAST_SR1);
+		PIN_IN(gpa3-6, DOWN, FAST_SR1);
+		PIN_IN(gpa3-7, DOWN, FAST_SR1);
+
+		PIN_IN(gpf1-0, NONE, FAST_SR1);
+		PIN_IN(gpf1-1, NONE, FAST_SR1);
+		PIN_IN(gpf1-2, DOWN, FAST_SR1);
+		PIN_IN(gpf1-4, UP, FAST_SR1);
+		PIN_OT(gpf1-5, NONE, FAST_SR1);
+		PIN_IN(gpf1-6, DOWN, FAST_SR1);
+		PIN_IN(gpf1-7, DOWN, FAST_SR1);
+
+		PIN_IN(gpf2-0, DOWN, FAST_SR1);
+		PIN_IN(gpf2-1, DOWN, FAST_SR1);
+		PIN_IN(gpf2-2, DOWN, FAST_SR1);
+		PIN_IN(gpf2-3, DOWN, FAST_SR1);
+
+		PIN_IN(gpf3-0, DOWN, FAST_SR1);
+		PIN_IN(gpf3-1, DOWN, FAST_SR1);
+		PIN_IN(gpf3-2, NONE, FAST_SR1);
+		PIN_IN(gpf3-3, DOWN, FAST_SR1);
+
+		PIN_IN(gpf4-0, DOWN, FAST_SR1);
+		PIN_IN(gpf4-1, DOWN, FAST_SR1);
+		PIN_IN(gpf4-2, DOWN, FAST_SR1);
+		PIN_IN(gpf4-3, DOWN, FAST_SR1);
+		PIN_IN(gpf4-4, DOWN, FAST_SR1);
+		PIN_IN(gpf4-5, DOWN, FAST_SR1);
+		PIN_IN(gpf4-6, DOWN, FAST_SR1);
+		PIN_IN(gpf4-7, DOWN, FAST_SR1);
+
+		PIN_IN(gpf5-0, DOWN, FAST_SR1);
+		PIN_IN(gpf5-1, DOWN, FAST_SR1);
+		PIN_IN(gpf5-2, DOWN, FAST_SR1);
+		PIN_IN(gpf5-3, DOWN, FAST_SR1);
+		PIN_OT(gpf5-4, NONE, FAST_SR1);
+		PIN_IN(gpf5-5, DOWN, FAST_SR1);
+		PIN_IN(gpf5-6, DOWN, FAST_SR1);
+		PIN_IN(gpf5-7, DOWN, FAST_SR1);
 	};
 
-	te_irq: te-irq {
+	te_irq: te-irq-pins {
 		samsung,pins = "gpf1-3";
 		samsung,pin-function = <0xf>;
 	};
@@ -1095,8 +1106,8 @@
 	pinctrl-0 = <&initial_cpif>;
 
 	initial_cpif: initial-state {
-		PIN(INPUT, gpv6-0, DOWN, FAST_SR1);
-		PIN(INPUT, gpv6-1, DOWN, FAST_SR1);
+		PIN_IN(gpv6-0, DOWN, FAST_SR1);
+		PIN_IN(gpv6-1, DOWN, FAST_SR1);
 	};
 };
 
@@ -1104,13 +1115,16 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&initial_ese>;
 
-	pcie_wlanen: pcie-wlanen {
-		PIN(INPUT, gpj2-0, UP, FAST_SR4);
+	pcie_wlanen: pcie-wlanen-pins {
+		samsung,pins = "gpj2-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS5433_PIN_DRV_FAST_SR4>;
 	};
 
 	initial_ese: initial-state {
-		PIN(INPUT, gpj2-1, DOWN, FAST_SR1);
-		PIN(INPUT, gpj2-2, DOWN, FAST_SR1);
+		PIN_IN(gpj2-1, DOWN, FAST_SR1);
+		PIN_IN(gpj2-2, DOWN, FAST_SR1);
 	};
 };
 
@@ -1119,11 +1133,11 @@
 	pinctrl-0 = <&initial_fsys>;
 
 	initial_fsys: initial-state {
-		PIN(INPUT, gpr3-0, NONE, FAST_SR1);
-		PIN(INPUT, gpr3-1, DOWN, FAST_SR1);
-		PIN(INPUT, gpr3-2, DOWN, FAST_SR1);
-		PIN(INPUT, gpr3-3, DOWN, FAST_SR1);
-		PIN(INPUT, gpr3-7, NONE, FAST_SR1);
+		PIN_IN(gpr3-0, NONE, FAST_SR1);
+		PIN_IN(gpr3-1, DOWN, FAST_SR1);
+		PIN_IN(gpr3-2, DOWN, FAST_SR1);
+		PIN_IN(gpr3-3, DOWN, FAST_SR1);
+		PIN_IN(gpr3-7, NONE, FAST_SR1);
 	};
 };
 
@@ -1132,14 +1146,14 @@
 	pinctrl-0 = <&initial_imem>;
 
 	initial_imem: initial-state {
-		PIN(INPUT, gpf0-0, UP, FAST_SR1);
-		PIN(INPUT, gpf0-1, UP, FAST_SR1);
-		PIN(INPUT, gpf0-2, DOWN, FAST_SR1);
-		PIN(INPUT, gpf0-3, UP, FAST_SR1);
-		PIN(INPUT, gpf0-4, DOWN, FAST_SR1);
-		PIN(INPUT, gpf0-5, NONE, FAST_SR1);
-		PIN(INPUT, gpf0-6, DOWN, FAST_SR1);
-		PIN(INPUT, gpf0-7, UP, FAST_SR1);
+		PIN_IN(gpf0-0, UP, FAST_SR1);
+		PIN_IN(gpf0-1, UP, FAST_SR1);
+		PIN_IN(gpf0-2, DOWN, FAST_SR1);
+		PIN_IN(gpf0-3, UP, FAST_SR1);
+		PIN_IN(gpf0-4, DOWN, FAST_SR1);
+		PIN_IN(gpf0-5, NONE, FAST_SR1);
+		PIN_IN(gpf0-6, DOWN, FAST_SR1);
+		PIN_IN(gpf0-7, UP, FAST_SR1);
 	};
 };
 
@@ -1148,7 +1162,7 @@
 	pinctrl-0 = <&initial_nfc>;
 
 	initial_nfc: initial-state {
-		PIN(INPUT, gpj0-2, DOWN, FAST_SR1);
+		PIN_IN(gpj0-2, DOWN, FAST_SR1);
 	};
 };
 
@@ -1157,53 +1171,53 @@
 	pinctrl-0 = <&initial_peric>;
 
 	initial_peric: initial-state {
-		PIN(INPUT, gpv7-0, DOWN, FAST_SR1);
-		PIN(INPUT, gpv7-1, DOWN, FAST_SR1);
-		PIN(INPUT, gpv7-2, NONE, FAST_SR1);
-		PIN(INPUT, gpv7-3, DOWN, FAST_SR1);
-		PIN(INPUT, gpv7-4, DOWN, FAST_SR1);
-		PIN(INPUT, gpv7-5, DOWN, FAST_SR1);
+		PIN_IN(gpv7-0, DOWN, FAST_SR1);
+		PIN_IN(gpv7-1, DOWN, FAST_SR1);
+		PIN_IN(gpv7-2, NONE, FAST_SR1);
+		PIN_IN(gpv7-3, DOWN, FAST_SR1);
+		PIN_IN(gpv7-4, DOWN, FAST_SR1);
+		PIN_IN(gpv7-5, DOWN, FAST_SR1);
 
-		PIN(INPUT, gpb0-4, DOWN, FAST_SR1);
+		PIN_IN(gpb0-4, DOWN, FAST_SR1);
 
-		PIN(INPUT, gpc0-2, DOWN, FAST_SR1);
-		PIN(INPUT, gpc0-5, DOWN, FAST_SR1);
-		PIN(INPUT, gpc0-7, DOWN, FAST_SR1);
+		PIN_IN(gpc0-2, DOWN, FAST_SR1);
+		PIN_IN(gpc0-5, DOWN, FAST_SR1);
+		PIN_IN(gpc0-7, DOWN, FAST_SR1);
 
-		PIN(INPUT, gpc1-1, DOWN, FAST_SR1);
+		PIN_IN(gpc1-1, DOWN, FAST_SR1);
 
-		PIN(INPUT, gpc3-4, NONE, FAST_SR1);
-		PIN(INPUT, gpc3-5, NONE, FAST_SR1);
-		PIN(INPUT, gpc3-6, NONE, FAST_SR1);
-		PIN(INPUT, gpc3-7, NONE, FAST_SR1);
+		PIN_IN(gpc3-4, NONE, FAST_SR1);
+		PIN_IN(gpc3-5, NONE, FAST_SR1);
+		PIN_IN(gpc3-6, NONE, FAST_SR1);
+		PIN_IN(gpc3-7, NONE, FAST_SR1);
 
-		PIN(OUTPUT, gpg0-0, NONE, FAST_SR1);
-		PIN(2, gpg0-1, DOWN, FAST_SR1);
+		PIN_OT(gpg0-0, NONE, FAST_SR1);
+		PIN_F2(gpg0-1, DOWN, FAST_SR1);
 
-		PIN(INPUT, gpd2-5, DOWN, FAST_SR1);
+		PIN_IN(gpd2-5, DOWN, FAST_SR1);
 
-		PIN(INPUT, gpd4-0, NONE, FAST_SR1);
-		PIN(INPUT, gpd4-1, DOWN, FAST_SR1);
-		PIN(INPUT, gpd4-2, DOWN, FAST_SR1);
-		PIN(INPUT, gpd4-3, DOWN, FAST_SR1);
-		PIN(INPUT, gpd4-4, DOWN, FAST_SR1);
+		PIN_IN(gpd4-0, NONE, FAST_SR1);
+		PIN_IN(gpd4-1, DOWN, FAST_SR1);
+		PIN_IN(gpd4-2, DOWN, FAST_SR1);
+		PIN_IN(gpd4-3, DOWN, FAST_SR1);
+		PIN_IN(gpd4-4, DOWN, FAST_SR1);
 
-		PIN(INPUT, gpd6-3, DOWN, FAST_SR1);
+		PIN_IN(gpd6-3, DOWN, FAST_SR1);
 
-		PIN(INPUT, gpd8-1, UP, FAST_SR1);
+		PIN_IN(gpd8-1, UP, FAST_SR1);
 
-		PIN(INPUT, gpg1-0, DOWN, FAST_SR1);
-		PIN(INPUT, gpg1-1, DOWN, FAST_SR1);
-		PIN(INPUT, gpg1-2, DOWN, FAST_SR1);
-		PIN(INPUT, gpg1-3, DOWN, FAST_SR1);
-		PIN(INPUT, gpg1-4, DOWN, FAST_SR1);
+		PIN_IN(gpg1-0, DOWN, FAST_SR1);
+		PIN_IN(gpg1-1, DOWN, FAST_SR1);
+		PIN_IN(gpg1-2, DOWN, FAST_SR1);
+		PIN_IN(gpg1-3, DOWN, FAST_SR1);
+		PIN_IN(gpg1-4, DOWN, FAST_SR1);
 
-		PIN(INPUT, gpg2-0, DOWN, FAST_SR1);
-		PIN(INPUT, gpg2-1, DOWN, FAST_SR1);
+		PIN_IN(gpg2-0, DOWN, FAST_SR1);
+		PIN_IN(gpg2-1, DOWN, FAST_SR1);
 
-		PIN(INPUT, gpg3-0, DOWN, FAST_SR1);
-		PIN(INPUT, gpg3-1, DOWN, FAST_SR1);
-		PIN(INPUT, gpg3-5, DOWN, FAST_SR1);
+		PIN_IN(gpg3-0, DOWN, FAST_SR1);
+		PIN_IN(gpg3-1, DOWN, FAST_SR1);
+		PIN_IN(gpg3-5, DOWN, FAST_SR1);
 	};
 };
 
@@ -1212,7 +1226,7 @@
 	pinctrl-0 = <&initial_touch>;
 
 	initial_touch: initial-state {
-		PIN(INPUT, gpj1-2, DOWN, FAST_SR1);
+		PIN_IN(gpj1-2, DOWN, FAST_SR1);
 	};
 };
 
diff --git a/arch/arm64/boot/dts/exynos/exynos5433.dtsi b/arch/arm64/boot/dts/exynos/exynos5433.dtsi
index 4422021cf4b2..bd6a354b9cb5 100644
--- a/arch/arm64/boot/dts/exynos/exynos5433.dtsi
+++ b/arch/arm64/boot/dts/exynos/exynos5433.dtsi
@@ -806,7 +806,8 @@
 		};
 
 		timer@101c0000 {
-			compatible = "samsung,exynos4210-mct";
+			compatible = "samsung,exynos5433-mct",
+				     "samsung,exynos4210-mct";
 			reg = <0x101c0000 0x800>;
 			interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>,
 				<GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>,
@@ -1585,7 +1586,7 @@
 			status = "disabled";
 		};
 
-		hsi2c_0: hsi2c@14e40000 {
+		hsi2c_0: i2c@14e40000 {
 			compatible = "samsung,exynos7-hsi2c";
 			reg = <0x14e40000 0x1000>;
 			interrupts = <GIC_SPI 428 IRQ_TYPE_LEVEL_HIGH>;
@@ -1598,7 +1599,7 @@
 			status = "disabled";
 		};
 
-		hsi2c_1: hsi2c@14e50000 {
+		hsi2c_1: i2c@14e50000 {
 			compatible = "samsung,exynos7-hsi2c";
 			reg = <0x14e50000 0x1000>;
 			interrupts = <GIC_SPI 429 IRQ_TYPE_LEVEL_HIGH>;
@@ -1611,7 +1612,7 @@
 			status = "disabled";
 		};
 
-		hsi2c_2: hsi2c@14e60000 {
+		hsi2c_2: i2c@14e60000 {
 			compatible = "samsung,exynos7-hsi2c";
 			reg = <0x14e60000 0x1000>;
 			interrupts = <GIC_SPI 430 IRQ_TYPE_LEVEL_HIGH>;
@@ -1624,7 +1625,7 @@
 			status = "disabled";
 		};
 
-		hsi2c_3: hsi2c@14e70000 {
+		hsi2c_3: i2c@14e70000 {
 			compatible = "samsung,exynos7-hsi2c";
 			reg = <0x14e70000 0x1000>;
 			interrupts = <GIC_SPI 431 IRQ_TYPE_LEVEL_HIGH>;
@@ -1637,7 +1638,7 @@
 			status = "disabled";
 		};
 
-		hsi2c_4: hsi2c@14ec0000 {
+		hsi2c_4: i2c@14ec0000 {
 			compatible = "samsung,exynos7-hsi2c";
 			reg = <0x14ec0000 0x1000>;
 			interrupts = <GIC_SPI 424 IRQ_TYPE_LEVEL_HIGH>;
@@ -1650,7 +1651,7 @@
 			status = "disabled";
 		};
 
-		hsi2c_5: hsi2c@14ed0000 {
+		hsi2c_5: i2c@14ed0000 {
 			compatible = "samsung,exynos7-hsi2c";
 			reg = <0x14ed0000 0x1000>;
 			interrupts = <GIC_SPI 425 IRQ_TYPE_LEVEL_HIGH>;
@@ -1663,7 +1664,7 @@
 			status = "disabled";
 		};
 
-		hsi2c_6: hsi2c@14ee0000 {
+		hsi2c_6: i2c@14ee0000 {
 			compatible = "samsung,exynos7-hsi2c";
 			reg = <0x14ee0000 0x1000>;
 			interrupts = <GIC_SPI 426 IRQ_TYPE_LEVEL_HIGH>;
@@ -1676,7 +1677,7 @@
 			status = "disabled";
 		};
 
-		hsi2c_7: hsi2c@14ef0000 {
+		hsi2c_7: i2c@14ef0000 {
 			compatible = "samsung,exynos7-hsi2c";
 			reg = <0x14ef0000 0x1000>;
 			interrupts = <GIC_SPI 427 IRQ_TYPE_LEVEL_HIGH>;
@@ -1689,7 +1690,7 @@
 			status = "disabled";
 		};
 
-		hsi2c_8: hsi2c@14d90000 {
+		hsi2c_8: i2c@14d90000 {
 			compatible = "samsung,exynos7-hsi2c";
 			reg = <0x14d90000 0x1000>;
 			interrupts = <GIC_SPI 443 IRQ_TYPE_LEVEL_HIGH>;
@@ -1702,7 +1703,7 @@
 			status = "disabled";
 		};
 
-		hsi2c_9: hsi2c@14da0000 {
+		hsi2c_9: i2c@14da0000 {
 			compatible = "samsung,exynos7-hsi2c";
 			reg = <0x14da0000 0x1000>;
 			interrupts = <GIC_SPI 444 IRQ_TYPE_LEVEL_HIGH>;
@@ -1715,7 +1716,7 @@
 			status = "disabled";
 		};
 
-		hsi2c_10: hsi2c@14de0000 {
+		hsi2c_10: i2c@14de0000 {
 			compatible = "samsung,exynos7-hsi2c";
 			reg = <0x14de0000 0x1000>;
 			interrupts = <GIC_SPI 445 IRQ_TYPE_LEVEL_HIGH>;
@@ -1728,7 +1729,7 @@
 			status = "disabled";
 		};
 
-		hsi2c_11: hsi2c@14df0000 {
+		hsi2c_11: i2c@14df0000 {
 			compatible = "samsung,exynos7-hsi2c";
 			reg = <0x14df0000 0x1000>;
 			interrupts = <GIC_SPI 446 IRQ_TYPE_LEVEL_HIGH>;
@@ -1819,7 +1820,7 @@
 			};
 		};
 
-		mshc_0: mshc@15540000 {
+		mshc_0: mmc@15540000 {
 			compatible = "samsung,exynos7-dw-mshc-smu";
 			interrupts = <GIC_SPI 225 IRQ_TYPE_LEVEL_HIGH>;
 			#address-cells = <1>;
@@ -1832,7 +1833,7 @@
 			status = "disabled";
 		};
 
-		mshc_1: mshc@15550000 {
+		mshc_1: mmc@15550000 {
 			compatible = "samsung,exynos7-dw-mshc-smu";
 			interrupts = <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>;
 			#address-cells = <1>;
@@ -1845,7 +1846,7 @@
 			status = "disabled";
 		};
 
-		mshc_2: mshc@15560000 {
+		mshc_2: mmc@15560000 {
 			compatible = "samsung,exynos7-dw-mshc-smu";
 			interrupts = <GIC_SPI 227 IRQ_TYPE_LEVEL_HIGH>;
 			#address-cells = <1>;
@@ -1858,26 +1859,22 @@
 			status = "disabled";
 		};
 
-		pdma0: pdma@15610000 {
+		pdma0: dma-controller@15610000 {
 			compatible = "arm,pl330", "arm,primecell";
 			reg = <0x15610000 0x1000>;
 			interrupts = <GIC_SPI 228 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cmu_fsys CLK_PDMA0>;
 			clock-names = "apb_pclk";
 			#dma-cells = <1>;
-			#dma-channels = <8>;
-			#dma-requests = <32>;
 		};
 
-		pdma1: pdma@15600000 {
+		pdma1: dma-controller@15600000 {
 			compatible = "arm,pl330", "arm,primecell";
 			reg = <0x15600000 0x1000>;
 			interrupts = <GIC_SPI 246 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cmu_fsys CLK_PDMA1>;
 			clock-names = "apb_pclk";
 			#dma-cells = <1>;
-			#dma-channels = <8>;
-			#dma-requests = <32>;
 		};
 
 		audio-subsystem@11400000 {
@@ -1885,21 +1882,18 @@
 			reg = <0x11400000 0x100>, <0x11500000 0x08>;
 			clocks = <&cmu_aud CLK_PCLK_SFR0_CTRL>;
 			clock-names = "sfr0_ctrl";
-			samsung,pmu-syscon = <&pmu_system_controller>;
 			power-domains = <&pd_aud>;
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges;
 
-			adma: adma@11420000 {
+			adma: dma-controller@11420000 {
 				compatible = "arm,pl330", "arm,primecell";
 				reg = <0x11420000 0x1000>;
 				interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&cmu_aud CLK_ACLK_DMAC>;
 				clock-names = "apb_pclk";
 				#dma-cells = <1>;
-				#dma-channels = <8>;
-				#dma-requests = <32>;
 				power-domains = <&pd_aud>;
 			};
 
diff --git a/arch/arm64/boot/dts/exynos/exynos7-espresso.dts b/arch/arm64/boot/dts/exynos/exynos7-espresso.dts
index 125c03f351d9..e38c59cf18dc 100644
--- a/arch/arm64/boot/dts/exynos/exynos7-espresso.dts
+++ b/arch/arm64/boot/dts/exynos/exynos7-espresso.dts
@@ -354,10 +354,10 @@
 };
 
 &pinctrl_alive {
-	pmic_irq: pmic-irq {
+	pmic_irq: pmic-irq-pins {
 		samsung,pins = "gpa0-2";
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
+		samsung,pin-drv = <EXYNOS7_PIN_DRV_LV4>;
 	};
 };
 
@@ -393,18 +393,18 @@
 };
 
 &pinctrl_bus1 {
-	usb30_vbus_en: usb30-vbus-en {
+	usb30_vbus_en: usb30-vbus-en-pins {
 		samsung,pins = "gph1-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-drv = <EXYNOS7_PIN_DRV_LV1>;
 	};
 
-	usb3drd_boost_en: usb3drd-boost-en {
+	usb3drd_boost_en: usb3drd-boost-en-pins {
 		samsung,pins = "gpf4-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-drv = <EXYNOS7_PIN_DRV_LV1>;
 	};
 };
 
@@ -412,6 +412,11 @@
 	status = "okay";
 };
 
+&usbdrd {
+	vdd10-supply = <&ldo4_reg>;
+	vdd33-supply = <&ldo6_reg>;
+};
+
 &usbdrd_phy {
 	vbus-supply = <&usb30_vbus_reg>;
 	vbus-boost-supply = <&usb3drd_boost_5v>;
diff --git a/arch/arm64/boot/dts/exynos/exynos7-pinctrl.dtsi b/arch/arm64/boot/dts/exynos/exynos7-pinctrl.dtsi
index 472dd649aa7e..ee9c24a226f3 100644
--- a/arch/arm64/boot/dts/exynos/exynos7-pinctrl.dtsi
+++ b/arch/arm64/boot/dts/exynos/exynos7-pinctrl.dtsi
@@ -9,10 +9,10 @@
  * device tree nodes in this file.
  */
 
-#include <dt-bindings/pinctrl/samsung.h>
+#include "exynos-pinctrl.h"
 
 &pinctrl_alive {
-	gpa0: gpa0 {
+	gpa0: gpa0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -29,7 +29,7 @@
 			     <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
 	};
 
-	gpa1: gpa1 {
+	gpa1: gpa1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -46,7 +46,7 @@
 			     <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
 	};
 
-	gpa2: gpa2 {
+	gpa2: gpa2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -54,7 +54,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpa3: gpa3 {
+	gpa3: gpa3-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -64,7 +64,7 @@
 };
 
 &pinctrl_bus0 {
-	gpb0: gpb0 {
+	gpb0: gpb0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -72,7 +72,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpc0: gpc0 {
+	gpc0: gpc0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -80,7 +80,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpc1: gpc1 {
+	gpc1: gpc1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -88,7 +88,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpc2: gpc2 {
+	gpc2: gpc2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -96,7 +96,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpc3: gpc3 {
+	gpc3: gpc3-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -104,7 +104,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpd0: gpd0 {
+	gpd0: gpd0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -112,7 +112,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpd1: gpd1 {
+	gpd1: gpd1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -120,7 +120,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpd2: gpd2 {
+	gpd2: gpd2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -128,7 +128,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpd4: gpd4 {
+	gpd4: gpd4-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -136,7 +136,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpd5: gpd5 {
+	gpd5: gpd5-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -144,7 +144,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpd6: gpd6 {
+	gpd6: gpd6-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -152,7 +152,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpd7: gpd7 {
+	gpd7: gpd7-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -160,7 +160,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpd8: gpd8 {
+	gpd8: gpd8-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -168,7 +168,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpg0: gpg0 {
+	gpg0: gpg0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -176,7 +176,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpg3: gpg3 {
+	gpg3: gpg3-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -184,170 +184,170 @@
 		#interrupt-cells = <2>;
 	};
 
-	hs_i2c10_bus: hs-i2c10-bus {
+	hs_i2c10_bus: hs-i2c10-bus-pins {
 		samsung,pins = "gpb0-1", "gpb0-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-drv = <EXYNOS7_PIN_DRV_LV1>;
 	};
 
-	hs_i2c11_bus: hs-i2c11-bus {
+	hs_i2c11_bus: hs-i2c11-bus-pins {
 		samsung,pins = "gpb0-3", "gpb0-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-drv = <EXYNOS7_PIN_DRV_LV1>;
 	};
 
-	hs_i2c2_bus: hs-i2c2-bus {
+	hs_i2c2_bus: hs-i2c2-bus-pins {
 		samsung,pins = "gpd0-3", "gpd0-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-drv = <EXYNOS7_PIN_DRV_LV1>;
 	};
 
-	uart0_data: uart0-data {
+	uart0_data: uart0-data-pins {
 		samsung,pins = "gpd0-0", "gpd0-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-drv = <EXYNOS7_PIN_DRV_LV1>;
 	};
 
-	uart0_fctl: uart0-fctl {
+	uart0_fctl: uart0-fctl-pins {
 		samsung,pins = "gpd0-2", "gpd0-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-drv = <EXYNOS7_PIN_DRV_LV1>;
 	};
 
-	uart2_data: uart2-data {
+	uart2_data: uart2-data-pins {
 		samsung,pins = "gpd1-4", "gpd1-5";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-drv = <EXYNOS7_PIN_DRV_LV1>;
 	};
 
-	hs_i2c3_bus: hs-i2c3-bus {
+	hs_i2c3_bus: hs-i2c3-bus-pins {
 		samsung,pins = "gpd1-3", "gpd1-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-drv = <EXYNOS7_PIN_DRV_LV1>;
 	};
 
-	uart1_data: uart1-data {
+	uart1_data: uart1-data-pins {
 		samsung,pins = "gpd1-0", "gpd1-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-drv = <EXYNOS7_PIN_DRV_LV1>;
 	};
 
-	uart1_fctl: uart1-fctl {
+	uart1_fctl: uart1-fctl-pins {
 		samsung,pins = "gpd1-2", "gpd1-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-drv = <EXYNOS7_PIN_DRV_LV1>;
 	};
 
-	hs_i2c0_bus: hs-i2c0-bus {
+	hs_i2c0_bus: hs-i2c0-bus-pins {
 		samsung,pins = "gpd2-1", "gpd2-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-drv = <EXYNOS7_PIN_DRV_LV1>;
 	};
 
-	hs_i2c1_bus: hs-i2c1-bus {
+	hs_i2c1_bus: hs-i2c1-bus-pins {
 		samsung,pins = "gpd2-3", "gpd2-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-drv = <EXYNOS7_PIN_DRV_LV1>;
 	};
 
-	hs_i2c9_bus: hs-i2c9-bus {
+	hs_i2c9_bus: hs-i2c9-bus-pins {
 		samsung,pins = "gpd2-7", "gpd2-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-drv = <EXYNOS7_PIN_DRV_LV1>;
 	};
 
-	pwm0_out: pwm0-out {
+	pwm0_out: pwm0-out-pins {
 		samsung,pins = "gpd2-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-drv = <EXYNOS7_PIN_DRV_LV1>;
 	};
 
-	pwm1_out: pwm1-out {
+	pwm1_out: pwm1-out-pins {
 		samsung,pins = "gpd2-5";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-drv = <EXYNOS7_PIN_DRV_LV1>;
 	};
 
-	pwm2_out: pwm2-out {
+	pwm2_out: pwm2-out-pins {
 		samsung,pins = "gpd2-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-drv = <EXYNOS7_PIN_DRV_LV1>;
 	};
 
-	pwm3_out: pwm3-out {
+	pwm3_out: pwm3-out-pins {
 		samsung,pins = "gpd2-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-drv = <EXYNOS7_PIN_DRV_LV1>;
 	};
 
-	hs_i2c8_bus: hs-i2c8-bus {
+	hs_i2c8_bus: hs-i2c8-bus-pins {
 		samsung,pins = "gpd5-3", "gpd5-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-drv = <EXYNOS7_PIN_DRV_LV1>;
 	};
 
-	uart3_data: uart3-data {
+	uart3_data: uart3-data-pins {
 		samsung,pins = "gpd5-0", "gpd5-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-drv = <EXYNOS7_PIN_DRV_LV1>;
 	};
 
-	spi2_bus: spi2-bus {
+	spi2_bus: spi2-bus-pins {
 		samsung,pins = "gpd5-0", "gpd5-1", "gpd5-2", "gpd5-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-drv = <EXYNOS7_PIN_DRV_LV1>;
 	};
 
-	spi1_bus: spi1-bus {
+	spi1_bus: spi1-bus-pins {
 		samsung,pins = "gpd6-2", "gpd6-3", "gpd6-4", "gpd6-5";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-drv = <EXYNOS7_PIN_DRV_LV1>;
 	};
 
-	spi0_bus: spi0-bus {
+	spi0_bus: spi0-bus-pins {
 		samsung,pins = "gpd8-0", "gpd8-1", "gpd6-0", "gpd6-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-drv = <EXYNOS7_PIN_DRV_LV1>;
 	};
 
-	hs_i2c4_bus: hs-i2c4-bus {
+	hs_i2c4_bus: hs-i2c4-bus-pins {
 		samsung,pins = "gpg3-1", "gpg3-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-drv = <EXYNOS7_PIN_DRV_LV1>;
 	};
 
-	hs_i2c5_bus: hs-i2c5-bus {
+	hs_i2c5_bus: hs-i2c5-bus-pins {
 		samsung,pins = "gpg3-3", "gpg3-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-drv = <EXYNOS7_PIN_DRV_LV1>;
 	};
 };
 
 &pinctrl_nfc {
-	gpj0: gpj0 {
+	gpj0: gpj0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -355,16 +355,16 @@
 		#interrupt-cells = <2>;
 	};
 
-	hs_i2c6_bus: hs-i2c6-bus {
+	hs_i2c6_bus: hs-i2c6-bus-pins {
 		samsung,pins = "gpj0-1", "gpj0-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-drv = <EXYNOS7_PIN_DRV_LV1>;
 	};
 };
 
 &pinctrl_touch {
-	gpj1: gpj1 {
+	gpj1: gpj1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -372,16 +372,16 @@
 		#interrupt-cells = <2>;
 	};
 
-	hs_i2c7_bus: hs-i2c7-bus {
+	hs_i2c7_bus: hs-i2c7-bus-pins {
 		samsung,pins = "gpj1-1", "gpj1-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-drv = <EXYNOS7_PIN_DRV_LV1>;
 	};
 };
 
 &pinctrl_ff {
-	gpg4: gpg4 {
+	gpg4: gpg4-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -389,16 +389,16 @@
 		#interrupt-cells = <2>;
 	};
 
-	spi3_bus: spi3-bus {
+	spi3_bus: spi3-bus-pins {
 		samsung,pins = "gpg4-0", "gpg4-1", "gpg4-2", "gpg4-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-drv = <EXYNOS7_PIN_DRV_LV1>;
 	};
 };
 
 &pinctrl_ese {
-	gpv7: gpv7 {
+	gpv7: gpv7-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -406,16 +406,16 @@
 		#interrupt-cells = <2>;
 	};
 
-	spi4_bus: spi4-bus {
+	spi4_bus: spi4-bus-pins {
 		samsung,pins = "gpv7-0", "gpv7-1", "gpv7-2", "gpv7-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-drv = <EXYNOS7_PIN_DRV_LV1>;
 	};
 };
 
 &pinctrl_fsys0 {
-	gpr4: gpr4 {
+	gpr4: gpr4-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -423,44 +423,44 @@
 		#interrupt-cells = <2>;
 	};
 
-	sd2_clk: sd2-clk {
+	sd2_clk: sd2-clk-pins {
 		samsung,pins = "gpr4-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
+		samsung,pin-drv = <EXYNOS7_PIN_DRV_LV4>;
 	};
 
-	sd2_cmd: sd2-cmd {
+	sd2_cmd: sd2-cmd-pins {
 		samsung,pins = "gpr4-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
+		samsung,pin-drv = <EXYNOS7_PIN_DRV_LV4>;
 	};
 
-	sd2_cd: sd2-cd {
+	sd2_cd: sd2-cd-pins {
 		samsung,pins = "gpr4-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
+		samsung,pin-drv = <EXYNOS7_PIN_DRV_LV4>;
 	};
 
-	sd2_bus1: sd2-bus-width1 {
+	sd2_bus1: sd2-bus-width1-pins {
 		samsung,pins = "gpr4-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
+		samsung,pin-drv = <EXYNOS7_PIN_DRV_LV4>;
 	};
 
-	sd2_bus4: sd2-bus-width4 {
+	sd2_bus4: sd2-bus-width4-pins {
 		samsung,pins = "gpr4-4", "gpr4-5", "gpr4-6";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV4>;
+		samsung,pin-drv = <EXYNOS7_PIN_DRV_LV4>;
 	};
 };
 
 &pinctrl_fsys1 {
-	gpr0: gpr0 {
+	gpr0: gpr0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -468,7 +468,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpr1: gpr1 {
+	gpr1: gpr1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -476,7 +476,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpr2: gpr2 {
+	gpr2: gpr2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -484,7 +484,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpr3: gpr3 {
+	gpr3: gpr3-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -492,105 +492,105 @@
 		#interrupt-cells = <2>;
 	};
 
-	sd0_clk: sd0-clk {
+	sd0_clk: sd0-clk-pins {
 		samsung,pins = "gpr0-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS7_FSYS1_PIN_DRV_LV2>;
 	};
 
-	sd0_cmd: sd0-cmd {
+	sd0_cmd: sd0-cmd-pins {
 		samsung,pins = "gpr0-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS7_FSYS1_PIN_DRV_LV2>;
 	};
 
-	sd0_ds: sd0-ds {
+	sd0_ds: sd0-ds-pins {
 		samsung,pins = "gpr0-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
 		samsung,pin-drv = <EXYNOS7_FSYS1_PIN_DRV_LV2>;
 	};
 
-	sd0_qrdy: sd0-qrdy {
+	sd0_qrdy: sd0-qrdy-pins {
 		samsung,pins = "gpr0-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
 		samsung,pin-drv = <EXYNOS7_FSYS1_PIN_DRV_LV2>;
 	};
 
-	sd0_bus1: sd0-bus-width1 {
+	sd0_bus1: sd0-bus-width1-pins {
 		samsung,pins = "gpr1-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS7_FSYS1_PIN_DRV_LV2>;
 	};
 
-	sd0_bus4: sd0-bus-width4 {
+	sd0_bus4: sd0-bus-width4-pins {
 		samsung,pins = "gpr1-1", "gpr1-2", "gpr1-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS7_FSYS1_PIN_DRV_LV2>;
 	};
 
-	sd0_bus8: sd0-bus-width8 {
+	sd0_bus8: sd0-bus-width8-pins {
 		samsung,pins = "gpr1-4", "gpr1-5", "gpr1-6", "gpr1-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS7_FSYS1_PIN_DRV_LV2>;
 	};
 
-	sd1_clk: sd1-clk {
+	sd1_clk: sd1-clk-pins {
 		samsung,pins = "gpr2-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS7_FSYS1_PIN_DRV_LV3>;
 	};
 
-	sd1_cmd: sd1-cmd {
+	sd1_cmd: sd1-cmd-pins {
 		samsung,pins = "gpr2-1";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS7_FSYS1_PIN_DRV_LV3>;
 	};
 
-	sd1_ds: sd1-ds {
+	sd1_ds: sd1-ds-pins {
 		samsung,pins = "gpr2-2";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
 		samsung,pin-drv = <EXYNOS7_FSYS1_PIN_DRV_LV4>;
 	};
 
-	sd1_qrdy: sd1-qrdy {
+	sd1_qrdy: sd1-qrdy-pins {
 		samsung,pins = "gpr2-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
 		samsung,pin-drv = <EXYNOS7_FSYS1_PIN_DRV_LV4>;
 	};
 
-	sd1_int: sd1-int {
+	sd1_int: sd1-int-pins {
 		samsung,pins = "gpr2-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
 		samsung,pin-drv = <EXYNOS7_FSYS1_PIN_DRV_LV4>;
 	};
 
-	sd1_bus1: sd1-bus-width1 {
+	sd1_bus1: sd1-bus-width1-pins {
 		samsung,pins = "gpr3-0";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS7_FSYS1_PIN_DRV_LV3>;
 	};
 
-	sd1_bus4: sd1-bus-width4 {
+	sd1_bus4: sd1-bus-width4-pins {
 		samsung,pins = "gpr3-1", "gpr3-2", "gpr3-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
 		samsung,pin-drv = <EXYNOS7_FSYS1_PIN_DRV_LV3>;
 	};
 
-	sd1_bus8: sd1-bus-width8 {
+	sd1_bus8: sd1-bus-width8-pins {
 		samsung,pins = "gpr3-4", "gpr3-5", "gpr3-6", "gpr3-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
@@ -599,7 +599,7 @@
 };
 
 &pinctrl_bus1 {
-	gpf0: gpf0 {
+	gpf0: gpf0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -607,7 +607,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpf1: gpf1 {
+	gpf1: gpf1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -615,7 +615,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpf2: gpf2 {
+	gpf2: gpf2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -623,7 +623,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpf3: gpf3 {
+	gpf3: gpf3-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -631,7 +631,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpf4: gpf4 {
+	gpf4: gpf4-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -639,7 +639,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpf5: gpf5 {
+	gpf5: gpf5-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -647,7 +647,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpg1: gpg1 {
+	gpg1: gpg1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -655,7 +655,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpg2: gpg2 {
+	gpg2: gpg2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -663,7 +663,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gph1: gph1 {
+	gph1: gph1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -671,7 +671,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpv6: gpv6 {
+	gpv6: gpv6-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -679,24 +679,24 @@
 		#interrupt-cells = <2>;
 	};
 
-	spi5_bus: spi5-bus {
+	spi5_bus: spi5-bus-pins {
 		samsung,pins = "gpf2-0", "gpf2-1", "gpf2-2", "gpf2-3";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-drv = <EXYNOS7_PIN_DRV_LV1>;
 	};
 
-	ufs_refclk_out: ufs-refclk-out {
+	ufs_refclk_out: ufs-refclk-out-pins {
 		samsung,pins = "gpg2-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV2>;
+		samsung,pin-drv = <EXYNOS7_PIN_DRV_LV2>;
 	};
 
-	ufs_rst_n: ufs-rst-n {
+	ufs_rst_n: ufs-rst-n-pins {
 		samsung,pins = "gph1-5";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
-		samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
+		samsung,pin-drv = <EXYNOS7_PIN_DRV_LV1>;
 	};
 };
diff --git a/arch/arm64/boot/dts/exynos/exynos7.dtsi b/arch/arm64/boot/dts/exynos/exynos7.dtsi
index c73a597ca66e..1cd771c90b47 100644
--- a/arch/arm64/boot/dts/exynos/exynos7.dtsi
+++ b/arch/arm64/boot/dts/exynos/exynos7.dtsi
@@ -142,26 +142,22 @@
 				<0x11006000 0x2000>;
 		};
 
-		pdma0: pdma@10e10000 {
+		pdma0: dma-controller@10e10000 {
 			compatible = "arm,pl330", "arm,primecell";
 			reg = <0x10E10000 0x1000>;
 			interrupts = <GIC_SPI 225 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&clock_fsys0 ACLK_PDMA0>;
 			clock-names = "apb_pclk";
 			#dma-cells = <1>;
-			#dma-channels = <8>;
-			#dma-requests = <32>;
 		};
 
-		pdma1: pdma@10eb0000 {
+		pdma1: dma-controller@10eb0000 {
 			compatible = "arm,pl330", "arm,primecell";
 			reg = <0x10EB0000 0x1000>;
 			interrupts = <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&clock_fsys0 ACLK_PDMA1>;
 			clock-names = "apb_pclk";
 			#dma-cells = <1>;
-			#dma-channels = <8>;
-			#dma-requests = <32>;
 		};
 
 		clock_topc: clock-controller@10570000 {
@@ -177,10 +173,11 @@
 			clocks = <&fin_pll>, <&clock_topc DOUT_SCLK_BUS0_PLL>,
 				 <&clock_topc DOUT_SCLK_BUS1_PLL>,
 				 <&clock_topc DOUT_SCLK_CC_PLL>,
-				 <&clock_topc DOUT_SCLK_MFC_PLL>;
+				 <&clock_topc DOUT_SCLK_MFC_PLL>,
+				 <&clock_topc DOUT_SCLK_AUD_PLL>;
 			clock-names = "fin_pll", "dout_sclk_bus0_pll",
 				      "dout_sclk_bus1_pll", "dout_sclk_cc_pll",
-				      "dout_sclk_mfc_pll";
+				      "dout_sclk_mfc_pll", "dout_sclk_aud_pll";
 		};
 
 		clock_top1: clock-controller@105e0000 {
@@ -218,12 +215,32 @@
 			compatible = "samsung,exynos7-clock-peric1";
 			reg = <0x14c80000 0xd00>;
 			#clock-cells = <1>;
-			clocks = <&fin_pll>, <&clock_top0 DOUT_ACLK_PERIC1>,
+			clocks = <&fin_pll>,
+				 <&clock_top0 DOUT_ACLK_PERIC1>,
 				 <&clock_top0 CLK_SCLK_UART1>,
 				 <&clock_top0 CLK_SCLK_UART2>,
-				 <&clock_top0 CLK_SCLK_UART3>;
-			clock-names = "fin_pll", "dout_aclk_peric1_66",
-				      "sclk_uart1", "sclk_uart2", "sclk_uart3";
+				 <&clock_top0 CLK_SCLK_UART3>,
+				 <&clock_top0 CLK_SCLK_SPI0>,
+				 <&clock_top0 CLK_SCLK_SPI1>,
+				 <&clock_top0 CLK_SCLK_SPI2>,
+				 <&clock_top0 CLK_SCLK_SPI3>,
+				 <&clock_top0 CLK_SCLK_SPI4>,
+				 <&clock_top0 CLK_SCLK_I2S1>,
+				 <&clock_top0 CLK_SCLK_PCM1>,
+				 <&clock_top0 CLK_SCLK_SPDIF>;
+			clock-names = "fin_pll",
+				      "dout_aclk_peric1_66",
+				      "sclk_uart1",
+				      "sclk_uart2",
+				      "sclk_uart3",
+				      "sclk_spi0",
+				      "sclk_spi1",
+				      "sclk_spi2",
+				      "sclk_spi3",
+				      "sclk_spi4",
+				      "sclk_i2s1",
+				      "sclk_pcm1",
+				      "sclk_spdif";
 		};
 
 		clock_peris: clock-controller@10040000 {
@@ -359,7 +376,7 @@
 			interrupts = <GIC_SPI 384 IRQ_TYPE_LEVEL_HIGH>;
 		};
 
-		hsi2c_0: hsi2c@13640000 {
+		hsi2c_0: i2c@13640000 {
 			compatible = "samsung,exynos7-hsi2c";
 			reg = <0x13640000 0x1000>;
 			interrupts = <GIC_SPI 441 IRQ_TYPE_LEVEL_HIGH>;
@@ -372,7 +389,7 @@
 			status = "disabled";
 		};
 
-		hsi2c_1: hsi2c@13650000 {
+		hsi2c_1: i2c@13650000 {
 			compatible = "samsung,exynos7-hsi2c";
 			reg = <0x13650000 0x1000>;
 			interrupts = <GIC_SPI 442 IRQ_TYPE_LEVEL_HIGH>;
@@ -385,7 +402,7 @@
 			status = "disabled";
 		};
 
-		hsi2c_2: hsi2c@14e60000 {
+		hsi2c_2: i2c@14e60000 {
 			compatible = "samsung,exynos7-hsi2c";
 			reg = <0x14e60000 0x1000>;
 			interrupts = <GIC_SPI 459 IRQ_TYPE_LEVEL_HIGH>;
@@ -398,7 +415,7 @@
 			status = "disabled";
 		};
 
-		hsi2c_3: hsi2c@14e70000 {
+		hsi2c_3: i2c@14e70000 {
 			compatible = "samsung,exynos7-hsi2c";
 			reg = <0x14e70000 0x1000>;
 			interrupts = <GIC_SPI 460 IRQ_TYPE_LEVEL_HIGH>;
@@ -411,7 +428,7 @@
 			status = "disabled";
 		};
 
-		hsi2c_4: hsi2c@13660000 {
+		hsi2c_4: i2c@13660000 {
 			compatible = "samsung,exynos7-hsi2c";
 			reg = <0x13660000 0x1000>;
 			interrupts = <GIC_SPI 443 IRQ_TYPE_LEVEL_HIGH>;
@@ -424,7 +441,7 @@
 			status = "disabled";
 		};
 
-		hsi2c_5: hsi2c@13670000 {
+		hsi2c_5: i2c@13670000 {
 			compatible = "samsung,exynos7-hsi2c";
 			reg = <0x13670000 0x1000>;
 			interrupts = <GIC_SPI 444 IRQ_TYPE_LEVEL_HIGH>;
@@ -437,7 +454,7 @@
 			status = "disabled";
 		};
 
-		hsi2c_6: hsi2c@14e00000 {
+		hsi2c_6: i2c@14e00000 {
 			compatible = "samsung,exynos7-hsi2c";
 			reg = <0x14e00000 0x1000>;
 			interrupts = <GIC_SPI 461 IRQ_TYPE_LEVEL_HIGH>;
@@ -450,7 +467,7 @@
 			status = "disabled";
 		};
 
-		hsi2c_7: hsi2c@13e10000 {
+		hsi2c_7: i2c@13e10000 {
 			compatible = "samsung,exynos7-hsi2c";
 			reg = <0x13e10000 0x1000>;
 			interrupts = <GIC_SPI 462 IRQ_TYPE_LEVEL_HIGH>;
@@ -463,7 +480,7 @@
 			status = "disabled";
 		};
 
-		hsi2c_8: hsi2c@14e20000 {
+		hsi2c_8: i2c@14e20000 {
 			compatible = "samsung,exynos7-hsi2c";
 			reg = <0x14e20000 0x1000>;
 			interrupts = <GIC_SPI 463 IRQ_TYPE_LEVEL_HIGH>;
@@ -476,7 +493,7 @@
 			status = "disabled";
 		};
 
-		hsi2c_9: hsi2c@13680000 {
+		hsi2c_9: i2c@13680000 {
 			compatible = "samsung,exynos7-hsi2c";
 			reg = <0x13680000 0x1000>;
 			interrupts = <GIC_SPI 445 IRQ_TYPE_LEVEL_HIGH>;
@@ -489,7 +506,7 @@
 			status = "disabled";
 		};
 
-		hsi2c_10: hsi2c@13690000 {
+		hsi2c_10: i2c@13690000 {
 			compatible = "samsung,exynos7-hsi2c";
 			reg = <0x13690000 0x1000>;
 			interrupts = <GIC_SPI 446 IRQ_TYPE_LEVEL_HIGH>;
@@ -502,7 +519,7 @@
 			status = "disabled";
 		};
 
-		hsi2c_11: hsi2c@136a0000 {
+		hsi2c_11: i2c@136a0000 {
 			compatible = "samsung,exynos7-hsi2c";
 			reg = <0x136a0000 0x1000>;
 			interrupts = <GIC_SPI 447 IRQ_TYPE_LEVEL_HIGH>;
@@ -663,16 +680,15 @@
 			reg = <0x15500000 0x100>;
 			clocks = <&clock_fsys0 ACLK_USBDRD300>,
 			       <&clock_fsys0 OSCCLK_PHY_CLKOUT_USB30_PHY>,
-			       <&clock_fsys0 PHYCLK_USBDRD300_UDRD30_PIPE_PCLK_USER>,
 			       <&clock_fsys0 PHYCLK_USBDRD300_UDRD30_PHYCLK_USER>,
+			       <&clock_fsys0 PHYCLK_USBDRD300_UDRD30_PIPE_PCLK_USER>,
 			       <&clock_fsys0 SCLK_USBDRD300_REFCLK>;
-			clock-names = "phy", "ref", "phy_pipe",
-				"phy_utmi", "itp";
+			clock-names = "phy", "ref", "phy_utmi", "phy_pipe", "itp";
 			samsung,pmu-syscon = <&pmu_system_controller>;
 			#phy-cells = <1>;
 		};
 
-		usbdrd3 {
+		usbdrd: usb {
 			compatible = "samsung,exynos7-dwusb3";
 			clocks = <&clock_fsys0 ACLK_USBDRD300>,
 			       <&clock_fsys0 SCLK_USBDRD300_SUSPENDCLK>,
diff --git a/arch/arm64/boot/dts/exynos/exynos7885-jackpotlte.dts b/arch/arm64/boot/dts/exynos/exynos7885-jackpotlte.dts
new file mode 100644
index 000000000000..5db9a81ac7bb
--- /dev/null
+++ b/arch/arm64/boot/dts/exynos/exynos7885-jackpotlte.dts
@@ -0,0 +1,112 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Samsung Galaxy A8 2018 (jackpotlte/SM-A530F) device tree source
+ *
+ * Copyright (c) 2021 Samsung Electronics Co., Ltd.
+ * Copyright (c) 2021 Dávid Virág
+ */
+
+/dts-v1/;
+#include "exynos7885.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	model = "Samsung Galaxy A8 (2018)";
+	compatible = "samsung,jackpotlte", "samsung,exynos7885";
+	chassis-type = "handset";
+
+	aliases {
+		serial0 = &serial_0;
+		serial1 = &serial_1;
+		serial2 = &serial_2;
+	};
+
+	chosen {
+		stdout-path = &serial_2;
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x0 0x80000000 0x3da00000>,
+		      <0x0 0xc0000000 0x40000000>,
+		      <0x8 0x80000000 0x40000000>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&key_volup &key_voldown &key_power>;
+
+		volup-key {
+			label = "Volume Up";
+			linux,code = <KEY_VOLUMEUP>;
+			gpios = <&gpa1 5 GPIO_ACTIVE_LOW>;
+		};
+
+		voldown-key {
+			label = "Volume Down";
+			linux,code = <KEY_VOLUMEDOWN>;
+			gpios = <&gpa1 6 GPIO_ACTIVE_LOW>;
+		};
+
+		power-key {
+			label = "Power";
+			linux,code = <KEY_POWER>;
+			gpios = <&gpa1 7 GPIO_ACTIVE_LOW>;
+			wakeup-source;
+		};
+	};
+};
+
+&mmc_0 {
+	status = "okay";
+	mmc-hs200-1_8v;
+	mmc-hs400-1_8v;
+	cap-mmc-highspeed;
+	non-removable;
+	mmc-hs400-enhanced-strobe;
+	card-detect-delay = <200>;
+	clock-frequency = <800000000>;
+	bus-width = <8>;
+	samsung,dw-mshc-ciu-div = <3>;
+	samsung,dw-mshc-sdr-timing = <0 4>;
+	samsung,dw-mshc-ddr-timing = <2 4>;
+	samsung,dw-mshc-hs400-timing = <0 2>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&sd0_clk_fast_slew_rate_3x &sd0_cmd &sd0_rdqs
+		     &sd0_bus1 &sd0_bus4 &sd0_bus8>;
+};
+
+&oscclk {
+	clock-frequency = <26000000>;
+};
+
+&pinctrl_alive {
+	key_volup: key-volup-pins {
+		samsung,pins = "gpa1-5";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
+
+	key_voldown: key-voldown-pins {
+		samsung,pins = "gpa1-6";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
+
+	key_power: key-power-pins {
+		samsung,pins = "gpa1-7";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
+};
+
+&serial_2 {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/exynos/exynos7885-pinctrl.dtsi b/arch/arm64/boot/dts/exynos/exynos7885-pinctrl.dtsi
new file mode 100644
index 000000000000..34bb12191955
--- /dev/null
+++ b/arch/arm64/boot/dts/exynos/exynos7885-pinctrl.dtsi
@@ -0,0 +1,855 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Samsung Exynos7885 SoC pin-mux and pin-config device tree source
+ *
+ * Copyright (c) 2017 Samsung Electronics Co., Ltd.
+ * Copyright (c) 2021 Dávid Virág
+ *
+ * Samsung's Exynos7885 SoC pin-mux and pin-config options are listed as
+ * device tree nodes in this file.
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include "exynos-pinctrl.h"
+
+&pinctrl_alive {
+	etc0: etc0-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	etc1: etc1-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpa0: gpa0-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		interrupt-parent = <&gic>;
+		interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
+	gpa1: gpa1-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		interrupt-parent = <&gic>;
+		interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
+	gpa2: gpa2-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpq0: gpq0-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	sim1_det_gpio: sim1-det-gpio-pins {
+		samsung,pins = "gpa2-5";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	sim0_det_gpio: sim0-det-gpio-pins {
+		samsung,pins = "gpa2-6";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	speedy_bus: speedy-bus-pins {
+		samsung,pins = "gpq0-2";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-con-pdn = <EXYNOS_PIN_PDN_PREV>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
+
+	/* UART_DEBUG */
+	uart2_bus: uart2-bus-pins {
+		samsung,pins = "gpq0-4", "gpq0-3";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+};
+
+&pinctrl_dispaud {
+	gpb0: gpb0-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpb1: gpb1-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpb2: gpb2-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	aud_codec_mclk: aud-codec-mclk-pins {
+		samsung,pins = "gpb0-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+	};
+
+	aud_codec_mclk_idle: aud-codec-mclk-idle-pins {
+		samsung,pins = "gpb0-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+	};
+
+	aud_codec_bus: aud-codec-bus-pins {
+		samsung,pins = "gpb0-1", "gpb0-2", "gpb0-3", "gpb0-4";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+	};
+
+	aud_codec_bus_idle: aud-codec-bus-idle-pins {
+		samsung,pins = "gpb0-1", "gpb0-2", "gpb0-3", "gpb0-4";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+	};
+
+	aud_loopback_bus: aud-loopback-bus-pins {
+		samsung,pins = "gpb1-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+	};
+
+	aud_loopback_bus_idle: aud-loopback-bus-idle-pins {
+		samsung,pins = "gpb1-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+	};
+
+	aud_fm_bus: aud-fm-bus-pins {
+		samsung,pins = "gpb1-1", "gpb1-2", "gpb1-3";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+	};
+
+	aud_fm_bus_idle: aud-fm-bus-idle-pins {
+		samsung,pins = "gpb1-1", "gpb1-2", "gpb1-3";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+	};
+
+	aud_spk_bus: aud-spk-bus-pins {
+		samsung,pins = "gpb2-0", "gpb2-1", "gpb2-2", "gpb2-3";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+	};
+
+	aud_spk_bus_idle: aud-spk-bus-idle-pins {
+		samsung,pins = "gpb2-0", "gpb2-1", "gpb2-2", "gpb2-3";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+	};
+};
+
+&pinctrl_fsys {
+	gpf0: gpf0-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpf2: gpf2-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpf3: gpf3-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpf4: gpf4-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	sd0_clk: sd0-clk-pins {
+		samsung,pins = "gpf0-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
+	};
+
+	sd0_clk_fast_slew_rate_1x: sd0-clk-fast-slew-rate-1x-pins {
+		samsung,pins = "gpf0-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
+
+	sd0_clk_fast_slew_rate_2x: sd0-clk-fast-slew-rate-2x-pins {
+		samsung,pins = "gpf0-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV2>;
+	};
+
+	sd0_clk_fast_slew_rate_3x: sd0-clk-fast-slew-rate-3x-pins {
+		samsung,pins = "gpf0-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
+	};
+
+	sd0_clk_fast_slew_rate_4x: sd0-clk-fast-slew-rate-4x-pins {
+		samsung,pins = "gpf0-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
+	};
+
+	sd0_cmd: sd0-cmd-pins {
+		samsung,pins = "gpf0-1";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
+	};
+
+	sd0_rdqs: sd0-rdqs-pins {
+		samsung,pins = "gpf0-2";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
+	};
+
+	sd0_bus1: sd0-bus-width1-pins {
+		samsung,pins = "gpf2-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
+	};
+
+	sd0_bus4: sd0-bus-width4-pins {
+		samsung,pins = "gpf2-1", "gpf2-2", "gpf2-3";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
+	};
+
+	sd0_bus8: sd0-bus-width8-pins {
+		samsung,pins = "gpf2-4", "gpf2-5", "gpf2-6", "gpf2-7";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
+	};
+
+	sd1_clk: sd1-clk-pins {
+		samsung,pins = "gpf3-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
+	};
+
+	sd1_clk_fast_slew_rate_1x: sd1-clk-fast-slew-rate-1x-pins {
+		samsung,pins = "gpf3-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
+
+	sd1_clk_fast_slew_rate_2x: sd1-clk-fast-slew-rate-2x-pins {
+		samsung,pins = "gpf3-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV2>;
+	};
+
+	sd1_clk_fast_slew_rate_3x: sd1-clk-fast-slew-rate-3x-pins {
+		samsung,pins = "gpf3-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
+	};
+
+	sd1_clk_fast_slew_rate_4x: sd1-clk-fast-slew-rate-4x-pins {
+		samsung,pins = "gpf3-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
+	};
+
+	sd1_cmd: sd1-cmd-pins {
+		samsung,pins = "gpf3-1";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
+	};
+
+	sd1_bus1: sd1-bus-width1-pins {
+		samsung,pins = "gpf3-2";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
+	};
+
+	sd1_bus4: sd1-bus-width4-pins {
+		samsung,pins = "gpf3-3", "gpf3-5";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
+	};
+
+	sd2_clk: sd2-clk-pins {
+		samsung,pins = "gpf4-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
+	};
+
+	sd2_clk_fast_slew_rate_1x: sd2-clk-fast-slew-rate-1x-pins {
+		samsung,pins = "gpf4-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
+
+	sd2_clk_fast_slew_rate_2x: sd2-clk-fast-slew-rate-2x-pins {
+		samsung,pins = "gpf4-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV2>;
+	};
+
+	sd2_clk_fast_slew_rate_3x: sd2-clk-fast-slew-rate-3x-pins {
+		samsung,pins = "gpf4-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
+	};
+
+	sd2_clk_fast_slew_rate_4x: sd2-clk-fast-slew-rate-4x-pins {
+		samsung,pins = "gpf4-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
+	};
+
+	sd2_cmd: sd2-cmd-pins {
+		samsung,pins = "gpf4-1";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
+	};
+
+	sd2_bus1: sd2-bus-width1-pins {
+		samsung,pins = "gpf4-2";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
+	};
+
+	sd2_bus4: sd2-bus-width4-pins {
+		samsung,pins = "gpf4-3", "gpf4-4", "gpf4-5";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
+	};
+};
+
+&pinctrl_top {
+	gpc0: gpc0-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpc1: gpc1-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpc2: gpc2-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpg0: gpg0-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpg1: gpg1-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpg2: gpg2-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpg3: gpg3-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpg4: gpg4-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpp0: gpp0-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpp1: gpp1-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpp2: gpp2-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpp3: gpp3-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpp4: gpp4-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpp5: gpp5-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpp6: gpp6-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpp7: gpp7-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpp8: gpp8-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	hs_i2c0_bus: hs-i2c0-bus-pins {
+		samsung,pins = "gpc1-1", "gpc1-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-con-pdn = <EXYNOS_PIN_PDN_OUT1>;
+		samsung,pin-pud-pdn = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
+
+	hs_i2c1_bus: hs-i2c1-bus-pins {
+		samsung,pins = "gpc1-3", "gpc1-2";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+		samsung,pin-con-pdn = <EXYNOS_PIN_PDN_OUT1>;
+		samsung,pin-pud-pdn = <EXYNOS_PIN_PULL_UP>;
+	};
+
+	hs_i2c2_bus: hs-i2c2-bus-pins {
+		samsung,pins = "gpc1-5", "gpc1-4";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+		samsung,pin-con-pdn = <EXYNOS_PIN_PDN_OUT1>;
+		samsung,pin-pud-pdn = <EXYNOS_PIN_PULL_UP>;
+	};
+
+	hs_i2c3_bus: hs-i2c3-bus-pins {
+		samsung,pins = "gpc1-7", "gpc1-6";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+		samsung,pin-con-pdn = <EXYNOS_PIN_PDN_OUT1>;
+		samsung,pin-pud-pdn = <EXYNOS_PIN_PULL_UP>;
+	};
+
+	/* USI0 UART */
+	uart3_bus_single: uart3-bus-single-pins {
+		samsung,pins = "gpc2-3", "gpc2-2", "gpc2-1", "gpc2-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	/* USI0 UART_HSI2C1 */
+	uart3_bus_dual: uart3-bus-dual-pins {
+		samsung,pins = "gpc2-1", "gpc2-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	/* USI0 HSI2C0 */
+	hs_i2c4_bus: hs-i2c4-bus-pins {
+		samsung,pins = "gpc2-1", "gpc2-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+		samsung,pin-con-pdn = <EXYNOS_PIN_PDN_OUT1>;
+		samsung,pin-pud-pdn = <EXYNOS_PIN_PULL_UP>;
+	};
+
+	/* USI0 HSI2C1 */
+	hs_i2c5_bus: hs-i2c5-bus-pins {
+		samsung,pins = "gpc2-3", "gpc2-2";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+		samsung,pin-con-pdn = <EXYNOS_PIN_PDN_OUT1>;
+		samsung,pin-pud-pdn = <EXYNOS_PIN_PULL_UP>;
+	};
+
+	/* USI0 SPI */
+	spi2_bus: spi2-bus-pins {
+		samsung,pins = "gpc2-1", "gpc2-0", "gpc2-3";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
+
+	spi2_cs: spi2-cs-pins {
+		samsung,pins = "gpc2-2";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
+
+	/* USI1 UART */
+	uart4_bus_single: uart4-bus-single-pins {
+		samsung,pins = "gpc2-7", "gpc2-6", "gpc2-5", "gpc2-4";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	/* USI1 UART_HSI2C1*/
+	uart4_bus_dual: uart4-bus-dual-pins {
+		samsung,pins = "gpc2-5", "gpc2-4";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	/* USI1 HSI2C0 */
+	hs_i2c6_bus: hs-i2c6-bus-pins {
+		samsung,pins = "gpc2-5", "gpc2-4";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+		samsung,pin-con-pdn = <EXYNOS_PIN_PDN_OUT1>;
+		samsung,pin-pud-pdn = <EXYNOS_PIN_PULL_UP>;
+	};
+
+	/* USI1 HSI2C1 */
+	hs_i2c7_bus: hs-i2c7-bus-pins {
+		samsung,pins = "gpc2-7", "gpc2-6";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+		samsung,pin-con-pdn = <EXYNOS_PIN_PDN_OUT1>;
+		samsung,pin-pud-pdn = <EXYNOS_PIN_PULL_UP>;
+	};
+
+	/* USI1 SPI */
+	spi3_bus: spi3-bus-pins {
+		samsung,pins = "gpc2-5", "gpc2-4", "gpc2-7";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
+
+	spi3_cs: spi3-cs-pins {
+		samsung,pins = "gpc2-6";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
+
+	fm_lna_en: fm-lna-en-pins {
+		samsung,pins = "gpg0-2";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+		samsung,pin-con-pdn = <EXYNOS_PIN_PDN_PREV>;
+		samsung,pin-pud-pdn = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-val = <1>;
+	};
+
+	uart1_bus: uart1-bus-pins {
+		samsung,pins = "gpg1-3", "gpg1-2", "gpg1-1", "gpg1-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	i2c7_bus: i2c7-bus-pins {
+		samsung,pins = "gpg1-5", "gpg1-4";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
+
+	aud_dmic_on: aud-dmic-on-pins {
+		samsung,pins = "gpg2-1";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+		samsung,pin-con-pdn = <EXYNOS_PIN_PDN_PREV>;
+		samsung,pin-val = <1>;
+	};
+
+	aud_dmic_off: aud-dmic-off-pins {
+		samsung,pins = "gpg2-1";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+		samsung,pin-con-pdn = <EXYNOS_PIN_PDN_PREV>;
+		samsung,pin-val = <0>;
+	};
+
+	/* UART_HEALTH */
+	uart0_bus: uart0-bus-pins {
+		samsung,pins = "gpp0-3", "gpp0-2", "gpp0-1", "gpp0-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	i2c0_bus: i2c0-bus-pins {
+		samsung,pins = "gpp1-1", "gpp1-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-con-pdn = <EXYNOS_PIN_PDN_PREV>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
+
+	i2c1_bus: i2c1-bus-pins {
+		samsung,pins = "gpp1-3", "gpp1-2";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-con-pdn = <EXYNOS_PIN_PDN_PREV>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
+
+	i2c2_bus: i2c2-bus-pins {
+		samsung,pins = "gpp2-1", "gpp2-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
+
+	i2c3_bus: i2c3-bus-pins {
+		samsung,pins = "gpp3-1", "gpp3-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
+
+	i2c4_bus: i2c4-bus-pins {
+		samsung,pins = "gpp4-1", "gpp4-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
+
+	i2c5_bus: i2c5-bus-pins {
+		samsung,pins = "gpp4-3", "gpp4-2";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
+
+	i2c6_bus: i2c6-bus-pins {
+		samsung,pins = "gpp4-5", "gpp4-4";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
+
+	/* SPI_ESE */
+	spi0_bus: spi0-bus-pins {
+		samsung,pins = "gpp5-3", "gpp5-2", "gpp5-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
+
+	spi0_cs: spi0-cs-pins {
+		samsung,pins = "gpp5-1";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
+
+	/* SPI_FP */
+	spi1_bus: spi1-bus-pins {
+		samsung,pins = "gpp6-3", "gpp6-2", "gpp6-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
+
+	spi1_cs: spi1-cs-pins {
+		samsung,pins = "gpp6-1";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
+
+	/* USI2 UART */
+	uart5_bus_single: uart5-bus-single-pins {
+		samsung,pins = "gpp8-1", "gpp8-0", "gpp7-1", "gpp7-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	  };
+
+	/* USI2 UART_HSI2C1 */
+	uart5_bus_dual: uart5-bus-dual-pins {
+		samsung,pins = "gpp7-1", "gpp7-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	/* USI2 HSI2C0 */
+	hs_i2c8_bus: hs-i2c8-bus-pins {
+		samsung,pins = "gpp7-1", "gpp7-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+		samsung,pin-con-pdn = <EXYNOS_PIN_PDN_OUT1>;
+		samsung,pin-pud-pdn = <EXYNOS_PIN_PULL_UP>;
+	};
+
+	/* USI2 HSI2C1 */
+	hs_i2c9_bus: hs-i2c9-bus-pins {
+		samsung,pins = "gpp8-1", "gpp8-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+		samsung,pin-con-pdn = <EXYNOS_PIN_PDN_OUT1>;
+		samsung,pin-pud-pdn = <EXYNOS_PIN_PULL_UP>;
+	};
+
+	/* USI2 SPI */
+	spi4_bus: spi4-bus-pins {
+		samsung,pins = "gpp7-1", "gpp7-0", "gpp8-1";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
+
+	spi4_cs: spi4-cs-pins {
+		samsung,pins = "gpp8-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
+};
diff --git a/arch/arm64/boot/dts/exynos/exynos7885.dtsi b/arch/arm64/boot/dts/exynos/exynos7885.dtsi
new file mode 100644
index 000000000000..23c2e0bb0a2c
--- /dev/null
+++ b/arch/arm64/boot/dts/exynos/exynos7885.dtsi
@@ -0,0 +1,455 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Samsung Exynos7885 SoC device tree source
+ *
+ * Copyright (c) 2021 Samsung Electronics Co., Ltd.
+ * Copyright (c) 2021 Dávid Virág
+ */
+
+#include <dt-bindings/clock/exynos7885.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+	compatible = "samsung,exynos7885";
+	#address-cells = <2>;
+	#size-cells = <1>;
+
+	interrupt-parent = <&gic>;
+
+	aliases {
+		pinctrl0 = &pinctrl_alive;
+		pinctrl1 = &pinctrl_dispaud;
+		pinctrl2 = &pinctrl_fsys;
+		pinctrl3 = &pinctrl_top;
+	};
+
+	arm-a53-pmu {
+		compatible = "arm,cortex-a53-pmu";
+		interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 218 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 219 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&cpu0>,
+				     <&cpu1>,
+				     <&cpu2>,
+				     <&cpu3>,
+				     <&cpu4>,
+				     <&cpu5>;
+	};
+
+	arm-a73-pmu {
+		compatible = "arm,cortex-a73-pmu";
+		interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&cpu6>,
+				     <&cpu7>;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu-map {
+			cluster0 {
+				core0 {
+					cpu = <&cpu0>;
+				};
+				core1 {
+					cpu = <&cpu1>;
+				};
+				core2 {
+					cpu = <&cpu2>;
+				};
+				core3 {
+					cpu = <&cpu3>;
+				};
+				core4 {
+					cpu = <&cpu4>;
+				};
+				core5 {
+					cpu = <&cpu5>;
+				};
+			};
+
+			cluster1 {
+				core0 {
+					cpu = <&cpu6>;
+				};
+				core1 {
+					cpu = <&cpu7>;
+				};
+			};
+		};
+
+		cpu0: cpu@100 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0x100>;
+			enable-method = "psci";
+		};
+
+		cpu1: cpu@101 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0x101>;
+			enable-method = "psci";
+		};
+
+		cpu2: cpu@102 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0x102>;
+			enable-method = "psci";
+		};
+
+		cpu3: cpu@103 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0x103>;
+			enable-method = "psci";
+		};
+
+		cpu4: cpu@200 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0x200>;
+			enable-method = "psci";
+		};
+
+		cpu5: cpu@201 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0x201>;
+			enable-method = "psci";
+		};
+
+		cpu6: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a73";
+			reg = <0x0>;
+			enable-method = "psci";
+		};
+
+		cpu7: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a73";
+			reg = <0x1>;
+			enable-method = "psci";
+		};
+	};
+
+	psci {
+		compatible = "arm,psci";
+		method = "smc";
+		cpu_suspend = <0xc4000001>;
+		cpu_off = <0x84000002>;
+		cpu_on = <0xc4000003>;
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		/* Hypervisor Virtual Timer interrupt is not wired to GIC */
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>;
+	};
+
+	fixed-rate-clocks {
+		oscclk: osc-clock {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-output-names = "oscclk";
+		};
+	};
+
+	soc: soc@0 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x0 0x0 0x20000000>;
+
+		chipid@10000000 {
+			compatible = "samsung,exynos850-chipid";
+			reg = <0x10000000 0x24>;
+		};
+
+		gic: interrupt-controller@12301000 {
+			compatible = "arm,gic-400";
+			#interrupt-cells = <3>;
+			#address-cells = <0>;
+			interrupt-controller;
+			reg = <0x12301000 0x1000>,
+			      <0x12302000 0x2000>,
+			      <0x12304000 0x2000>,
+			      <0x12306000 0x2000>;
+			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(8) |
+						 IRQ_TYPE_LEVEL_HIGH)>;
+		};
+
+		cmu_peri: clock-controller@10010000 {
+			compatible = "samsung,exynos7885-cmu-peri";
+			reg = <0x10010000 0x8000>;
+			#clock-cells = <1>;
+
+			clocks = <&oscclk>,
+				 <&cmu_top CLK_DOUT_PERI_BUS>,
+				 <&cmu_top CLK_DOUT_PERI_SPI0>,
+				 <&cmu_top CLK_DOUT_PERI_SPI1>,
+				 <&cmu_top CLK_DOUT_PERI_UART0>,
+				 <&cmu_top CLK_DOUT_PERI_UART1>,
+				 <&cmu_top CLK_DOUT_PERI_UART2>,
+				 <&cmu_top CLK_DOUT_PERI_USI0>,
+				 <&cmu_top CLK_DOUT_PERI_USI1>,
+				 <&cmu_top CLK_DOUT_PERI_USI2>;
+			clock-names = "oscclk",
+				      "dout_peri_bus",
+				      "dout_peri_spi0",
+				      "dout_peri_spi1",
+				      "dout_peri_uart0",
+				      "dout_peri_uart1",
+				      "dout_peri_uart2",
+				      "dout_peri_usi0",
+				      "dout_peri_usi1",
+				      "dout_peri_usi2";
+		};
+
+		cmu_core: clock-controller@12000000 {
+			compatible = "samsung,exynos7885-cmu-core";
+			reg = <0x12000000 0x8000>;
+			#clock-cells = <1>;
+
+			clocks = <&oscclk>,
+				 <&cmu_top CLK_DOUT_CORE_BUS>,
+				 <&cmu_top CLK_DOUT_CORE_CCI>,
+				 <&cmu_top CLK_DOUT_CORE_G3D>;
+			clock-names = "oscclk",
+				      "dout_core_bus",
+				      "dout_core_cci",
+				      "dout_core_g3d";
+		};
+
+		cmu_top: clock-controller@12060000 {
+			compatible = "samsung,exynos7885-cmu-top";
+			reg = <0x12060000 0x8000>;
+			#clock-cells = <1>;
+
+			clocks = <&oscclk>;
+			clock-names = "oscclk";
+		};
+
+		cmu_fsys: clock-controller@13400000 {
+			compatible = "samsung,exynos7885-cmu-fsys";
+			reg = <0x13400000 0x8000>;
+			#clock-cells = <1>;
+
+			clocks = <&oscclk>,
+				 <&cmu_top CLK_DOUT_FSYS_BUS>,
+				 <&cmu_top CLK_DOUT_FSYS_MMC_CARD>,
+				 <&cmu_top CLK_DOUT_FSYS_MMC_EMBD>,
+				 <&cmu_top CLK_DOUT_FSYS_MMC_SDIO>,
+				 <&cmu_top CLK_DOUT_FSYS_USB30DRD>;
+			clock-names = "oscclk",
+				      "dout_fsys_bus",
+				      "dout_fsys_mmc_card",
+				      "dout_fsys_mmc_embd",
+				      "dout_fsys_mmc_sdio",
+				      "dout_fsys_usb30drd";
+		};
+
+		pinctrl_alive: pinctrl@11cb0000 {
+			compatible = "samsung,exynos7885-pinctrl";
+			reg = <0x11cb0000 0x1000>;
+
+			wakeup-interrupt-controller {
+				compatible = "samsung,exynos7-wakeup-eint";
+				interrupt-parent = <&gic>;
+				interrupts = <GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>;
+			};
+		};
+
+		pinctrl_fsys: pinctrl@13430000 {
+			compatible = "samsung,exynos7885-pinctrl";
+			reg = <0x13430000 0x1000>;
+			interrupts = <GIC_SPI 150 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		pinctrl_top: pinctrl@139b0000 {
+			compatible = "samsung,exynos7885-pinctrl";
+			reg = <0x139b0000 0x1000>;
+			interrupts = <GIC_SPI 266 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		pinctrl_dispaud: pinctrl@148f0000 {
+			compatible = "samsung,exynos7885-pinctrl";
+			reg = <0x148f0000 0x1000>;
+			interrupts = <GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		pmu_system_controller: system-controller@11c80000 {
+			compatible = "samsung,exynos7-pmu", "syscon";
+			reg = <0x11c80000 0x10000>;
+		};
+
+		mmc_0: mmc@13500000 {
+			compatible = "samsung,exynos7-dw-mshc-smu";
+			reg = <0x13500000 0x2000>;
+			interrupts = <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			clocks = <&cmu_fsys CLK_GOUT_MMC_EMBD_ACLK>,
+				 <&cmu_fsys CLK_GOUT_MMC_EMBD_SDCLKIN>;
+			clock-names = "biu", "ciu";
+			fifo-depth = <0x40>;
+			status = "disabled";
+		};
+
+		serial_0: serial@13800000 {
+			compatible = "samsung,exynos5433-uart";
+			reg = <0x13800000 0x100>;
+			interrupts = <GIC_SPI 246 IRQ_TYPE_LEVEL_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&uart0_bus>;
+			clocks = <&cmu_peri CLK_GOUT_UART0_PCLK>,
+				 <&cmu_peri CLK_GOUT_UART0_EXT_UCLK>;
+			clock-names = "uart", "clk_uart_baud0";
+			samsung,uart-fifosize = <64>;
+			status = "disabled";
+		};
+
+		serial_1: serial@13810000 {
+			compatible = "samsung,exynos5433-uart";
+			reg = <0x13810000 0x100>;
+			interrupts = <GIC_SPI 247 IRQ_TYPE_LEVEL_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&uart1_bus>;
+			clocks = <&cmu_peri CLK_GOUT_UART1_PCLK>,
+				 <&cmu_peri CLK_GOUT_UART1_EXT_UCLK>;
+			clock-names = "uart", "clk_uart_baud0";
+			samsung,uart-fifosize = <256>;
+			status = "disabled";
+		};
+
+		serial_2: serial@13820000 {
+			compatible = "samsung,exynos5433-uart";
+			reg = <0x13820000 0x100>;
+			interrupts = <GIC_SPI 279 IRQ_TYPE_LEVEL_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&uart2_bus>;
+			clocks = <&cmu_peri CLK_GOUT_UART2_PCLK>,
+				 <&cmu_peri CLK_GOUT_UART2_EXT_UCLK>;
+			clock-names = "uart", "clk_uart_baud0";
+			samsung,uart-fifosize = <256>;
+			status = "disabled";
+		};
+
+		i2c_0: i2c@13830000 {
+			compatible = "samsung,s3c2440-i2c";
+			reg = <0x13830000 0x100>;
+			interrupts = <GIC_SPI 248 IRQ_TYPE_LEVEL_HIGH>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&i2c0_bus>;
+			clocks = <&cmu_peri CLK_GOUT_I2C0_PCLK>;
+			clock-names = "i2c";
+			status = "disabled";
+		};
+
+		i2c_1: i2c@13840000 {
+			compatible = "samsung,s3c2440-i2c";
+			reg = <0x13840000 0x100>;
+			interrupts = <GIC_SPI 249 IRQ_TYPE_LEVEL_HIGH>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&i2c1_bus>;
+			clocks = <&cmu_peri CLK_GOUT_I2C1_PCLK>;
+			clock-names = "i2c";
+			status = "disabled";
+		};
+
+		i2c_2: i2c@13850000 {
+			compatible = "samsung,s3c2440-i2c";
+			reg = <0x13850000 0x100>;
+			interrupts = <GIC_SPI 250 IRQ_TYPE_LEVEL_HIGH>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&i2c2_bus>;
+			clocks = <&cmu_peri CLK_GOUT_I2C2_PCLK>;
+			clock-names = "i2c";
+			status = "disabled";
+		};
+
+		i2c_3: i2c@13860000 {
+			compatible = "samsung,s3c2440-i2c";
+			reg = <0x13860000 0x100>;
+			interrupts = <GIC_SPI 251 IRQ_TYPE_LEVEL_HIGH>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&i2c3_bus>;
+			clocks = <&cmu_peri CLK_GOUT_I2C3_PCLK>;
+			clock-names = "i2c";
+			status = "disabled";
+		};
+
+		i2c_4: i2c@13870000 {
+			compatible = "samsung,s3c2440-i2c";
+			reg = <0x13870000 0x100>;
+			interrupts = <GIC_SPI 252 IRQ_TYPE_LEVEL_HIGH>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&i2c4_bus>;
+			clocks = <&cmu_peri CLK_GOUT_I2C4_PCLK>;
+			clock-names = "i2c";
+			status = "disabled";
+		};
+
+		i2c_5: i2c@13880000 {
+			compatible = "samsung,s3c2440-i2c";
+			reg = <0x13880000 0x100>;
+			interrupts = <GIC_SPI 253 IRQ_TYPE_LEVEL_HIGH>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&i2c5_bus>;
+			clocks = <&cmu_peri CLK_GOUT_I2C5_PCLK>;
+			clock-names = "i2c";
+			status = "disabled";
+		};
+
+		i2c_6: i2c@13890000 {
+			compatible = "samsung,s3c2440-i2c";
+			reg = <0x13890000 0x100>;
+			interrupts = <GIC_SPI 254 IRQ_TYPE_LEVEL_HIGH>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&i2c6_bus>;
+			clocks = <&cmu_peri CLK_GOUT_I2C6_PCLK>;
+			clock-names = "i2c";
+			status = "disabled";
+		};
+
+		i2c_7: i2c@11cd0000 {
+			compatible = "samsung,s3c2440-i2c";
+			reg = <0x11cd0000 0x100>;
+			interrupts = <GIC_SPI 255 IRQ_TYPE_LEVEL_HIGH>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&i2c7_bus>;
+			clocks = <&cmu_peri CLK_GOUT_I2C7_PCLK>;
+			clock-names = "i2c";
+			status = "disabled";
+		};
+	};
+};
+
+#include "exynos7885-pinctrl.dtsi"
+#include "arm/exynos-syscon-restart.dtsi"
diff --git a/arch/arm64/boot/dts/exynos/exynos850-e850-96.dts b/arch/arm64/boot/dts/exynos/exynos850-e850-96.dts
new file mode 100644
index 000000000000..f52a55f644f7
--- /dev/null
+++ b/arch/arm64/boot/dts/exynos/exynos850-e850-96.dts
@@ -0,0 +1,200 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * WinLink E850-96 board device tree source
+ *
+ * Copyright (C) 2018 Samsung Electronics Co., Ltd.
+ * Copyright (C) 2021 Linaro Ltd.
+ *
+ * Device tree source file for WinLink's E850-96 board which is based on
+ * Samsung Exynos850 SoC.
+ */
+
+/dts-v1/;
+
+#include "exynos850.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+	model = "WinLink E850-96 board";
+	compatible = "winlink,e850-96", "samsung,exynos850";
+
+	aliases {
+		mmc0 = &mmc_0;
+		serial0 = &serial_0;
+	};
+
+	chosen {
+		stdout-path = &serial_0;
+	};
+
+	/*
+	 * RAM: 4 GiB (eMCP):
+	 *   - 2 GiB at 0x80000000
+	 *   - 2 GiB at 0x880000000
+	 *
+	 * 0xbab00000..0xbfffffff: secure memory (85 MiB).
+	 */
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x0 0x80000000 0x3ab00000>,
+		      <0x0 0xc0000000 0x40000000>,
+		      <0x8 0x80000000 0x80000000>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&key_voldown_pins &key_volup_pins>;
+
+		volume-down-key {
+			label = "Volume Down";
+			linux,code = <KEY_VOLUMEDOWN>;
+			gpios = <&gpa1 0 GPIO_ACTIVE_LOW>;
+		};
+
+		volume-up-key {
+			label = "Volume Up";
+			linux,code = <KEY_VOLUMEUP>;
+			gpios = <&gpa0 7 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		/* HEART_BEAT_LED */
+		user_led1: led-1 {
+			label = "yellow:user1";
+			gpios = <&gpg2 2 GPIO_ACTIVE_HIGH>;
+			color = <LED_COLOR_ID_YELLOW>;
+			function = LED_FUNCTION_HEARTBEAT;
+			linux,default-trigger = "heartbeat";
+		};
+
+		/* eMMC_LED */
+		user_led2: led-2 {
+			label = "yellow:user2";
+			gpios = <&gpg2 3 GPIO_ACTIVE_HIGH>;
+			color = <LED_COLOR_ID_YELLOW>;
+			linux,default-trigger = "mmc0";
+		};
+
+		/* SD_LED */
+		user_led3: led-3 {
+			label = "white:user3";
+			gpios = <&gpg2 4 GPIO_ACTIVE_HIGH>;
+			color = <LED_COLOR_ID_WHITE>;
+			function = LED_FUNCTION_SD;
+			linux,default-trigger = "mmc2";
+		};
+
+		/* WIFI_LED */
+		wlan_active_led: led-4 {
+			label = "yellow:wlan";
+			gpios = <&gpg2 6 GPIO_ACTIVE_HIGH>;
+			color = <LED_COLOR_ID_YELLOW>;
+			function = LED_FUNCTION_WLAN;
+			linux,default-trigger = "phy0tx";
+			default-state = "off";
+		};
+
+		/* BLUETOOTH_LED */
+		bt_active_led: led-5 {
+			label = "blue:bt";
+			gpios = <&gpg2 7 GPIO_ACTIVE_HIGH>;
+			color = <LED_COLOR_ID_BLUE>;
+			function = LED_FUNCTION_BLUETOOTH;
+			linux,default-trigger = "hci0rx";
+			default-state = "off";
+		};
+	};
+
+	/*
+	 * RTC clock (XrtcXTI); external, must be 32.768 kHz.
+	 *
+	 * TODO: Remove this once RTC clock is implemented properly as part of
+	 *       PMIC driver.
+	 */
+	rtcclk: clock-rtcclk {
+		compatible = "fixed-clock";
+		clock-output-names = "rtcclk";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+	};
+};
+
+&cmu_hsi {
+	clocks = <&oscclk>, <&rtcclk>,
+		 <&cmu_top CLK_DOUT_HSI_BUS>,
+		 <&cmu_top CLK_DOUT_HSI_MMC_CARD>,
+		 <&cmu_top CLK_DOUT_HSI_USB20DRD>;
+	clock-names = "oscclk", "rtcclk", "dout_hsi_bus",
+		      "dout_hsi_mmc_card", "dout_hsi_usb20drd";
+};
+
+&mmc_0 {
+	status = "okay";
+	mmc-hs200-1_8v;
+	mmc-hs400-1_8v;
+	cap-mmc-highspeed;
+	non-removable;
+	mmc-hs400-enhanced-strobe;
+	card-detect-delay = <200>;
+	clock-frequency = <800000000>;
+	bus-width = <8>;
+	samsung,dw-mshc-ciu-div = <3>;
+	samsung,dw-mshc-sdr-timing = <0 4>;
+	samsung,dw-mshc-ddr-timing = <2 4>;
+	samsung,dw-mshc-hs400-timing = <0 2>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&sd0_clk_pins &sd0_cmd_pins &sd0_rdqs_pins &sd0_nreset_pins
+		     &sd0_bus1_pins &sd0_bus4_pins &sd0_bus8_pins>;
+};
+
+&oscclk {
+	clock-frequency = <26000000>;
+};
+
+&pinctrl_alive {
+	key_voldown_pins: key-voldown-pins {
+		samsung,pins = "gpa1-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_EINT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
+
+	key_volup_pins: key-volup-pins {
+		samsung,pins = "gpa0-7";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_EINT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
+};
+
+&rtc {
+	status = "okay";
+	clocks = <&cmu_apm CLK_GOUT_RTC_PCLK>, <&rtcclk>;
+	clock-names = "rtc", "rtc_src";
+};
+
+&serial_0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>;
+};
+
+&usi_uart {
+	samsung,clkreq-on; /* needed for UART mode */
+	status = "okay";
+};
+
+&watchdog_cl0 {
+	status = "okay";
+};
+
+&watchdog_cl1 {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/exynos/exynos850-pinctrl.dtsi b/arch/arm64/boot/dts/exynos/exynos850-pinctrl.dtsi
new file mode 100644
index 000000000000..424bc80bde68
--- /dev/null
+++ b/arch/arm64/boot/dts/exynos/exynos850-pinctrl.dtsi
@@ -0,0 +1,663 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Samsung's Exynos850 SoC pin-mux and pin-config device tree source
+ *
+ * Copyright (C) 2017 Samsung Electronics Co., Ltd.
+ * Copyright (C) 2021 Linaro Ltd.
+ *
+ * Samsung's Exynos850 SoC pin-mux and pin-config options are listed as device
+ * tree nodes in this file.
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include "exynos-pinctrl.h"
+
+&pinctrl_alive {
+	gpa0: gpa0-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		interrupt-parent = <&gic>;
+		interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
+	gpa1: gpa1-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		interrupt-parent = <&gic>;
+		interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
+	gpa2: gpa2-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		interrupt-parent = <&gic>;
+		interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
+	gpa3: gpa3-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		interrupt-parent = <&gic>;
+		interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
+	gpa4: gpa4-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		interrupt-parent = <&gic>;
+		interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
+	gpq0: gpq0-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	/* I2C5 (also called CAM_PMIC_I2C in TRM) */
+	i2c5_pins: i2c5-pins {
+		samsung,pins = "gpa3-5", "gpa3-6";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
+
+	/* I2C6 (also called MOTOR_I2C in TRM) */
+	i2c6_pins: i2c6-pins {
+		samsung,pins = "gpa3-7", "gpa4-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_3>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
+
+	/* USI: UART_DEBUG_0 pins */
+	uart0_pins: uart0-pins {
+		samsung,pins = "gpq0-0", "gpq0-1";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	/* USI: UART_DEBUG_1 pins */
+	uart1_pins: uart1-pins {
+		samsung,pins = "gpa3-7", "gpa4-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+};
+
+&pinctrl_cmgp {
+	gpm0: gpm0-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		interrupt-parent = <&gic>;
+		interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
+	gpm1: gpm1-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		interrupt-parent = <&gic>;
+		interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
+	gpm2: gpm2-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		interrupt-parent = <&gic>;
+		interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
+	gpm3: gpm3-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		interrupt-parent = <&gic>;
+		interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
+	gpm4: gpm4-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		interrupt-parent = <&gic>;
+		interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
+	gpm5: gpm5-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		interrupt-parent = <&gic>;
+		interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
+	gpm6: gpm6-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		interrupt-parent = <&gic>;
+		interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
+	gpm7: gpm7-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		interrupt-parent = <&gic>;
+		interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
+	/* USI_CMGP0: HSI2C function */
+	hsi2c3_pins: hsi2c3-pins {
+		samsung,pins = "gpm0-0", "gpm1-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
+
+	/* USI_CMGP0: UART function (4 pins, Auto Flow Control) */
+	uart1_single_pins: uart1-single-pins {
+		samsung,pins = "gpm0-0", "gpm1-0", "gpm2-0", "gpm3-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	/* USI_CMGP0: UART function (2 pins, Non-Auto Flow Control) */
+	uart1_dual_pins: uart1-dual-pins {
+		samsung,pins = "gpm0-0", "gpm1-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	/* USI_CMGP0: SPI function */
+	spi1_pins: spi1-pins {
+		samsung,pins = "gpm0-0", "gpm1-0", "gpm2-0", "gpm3-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
+
+	/* USI_CMGP1: HSI2C function */
+	hsi2c4_pins: hsi2c4-pins {
+		samsung,pins = "gpm4-0", "gpm5-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
+
+	/* USI_CMGP1: UART function (4 pins, Auto Flow Control) */
+	uart2_single_pins: uart2-single-pins {
+		samsung,pins = "gpm4-0", "gpm5-0", "gpm6-0", "gpm7-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	/* USI_CMGP1: UART function (2 pins, Non-Auto Flow Control) */
+	uart2_dual_pins: uart2-dual-pins {
+		samsung,pins = "gpm4-0", "gpm5-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+
+	/* USI_CMGP1: SPI function */
+	spi2_pins: spi2-pins {
+		samsung,pins = "gpm4-0", "gpm5-0", "gpm6-0", "gpm7-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
+};
+
+&pinctrl_aud {
+	gpb0: gpb0-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpb1: gpb1-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	aud_codec_mclk_pins: aud-codec-mclk-pins {
+		samsung,pins = "gpb0-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+	};
+
+	aud_codec_mclk_idle_pins: aud-codec-mclk-idle-pins {
+		samsung,pins = "gpb0-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+	};
+
+	aud_i2s0_pins: aud-i2s0-pins {
+		samsung,pins = "gpb0-1", "gpb0-2", "gpb0-3", "gpb0-4";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+	};
+
+	aud_i2s0_idle_pins: aud-i2s0-idle-pins {
+		samsung,pins = "gpb0-1", "gpb0-2", "gpb0-3", "gpb0-4";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+	};
+
+	aud_i2s1_pins: aud-i2s1-pins {
+		samsung,pins = "gpb1-0", "gpb1-1", "gpb1-2", "gpb1-3";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+	};
+
+	aud_i2s1_idle_pins: aud-i2s1-idle-pins {
+		samsung,pins = "gpb1-0", "gpb1-1", "gpb1-2", "gpb1-3";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+	};
+
+	aud_fm_pins: aud-fm-pins {
+		samsung,pins = "gpb1-4";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+	};
+
+	aud_fm_idle_pins: aud-fm-idle-pins {
+		samsung,pins = "gpb1-4";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+	};
+};
+
+&pinctrl_hsi {
+	gpf2: gpf2-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	sd2_clk_pins: sd2-clk-pins {
+		samsung,pins = "gpf2-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS850_HSI_PIN_DRV_LV2>;
+	};
+
+	sd2_cmd_pins: sd2-cmd-pins {
+		samsung,pins = "gpf2-1";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS850_HSI_PIN_DRV_LV2>;
+	 };
+
+	sd2_bus1_pins: sd2-bus1-pins {
+		samsung,pins = "gpf2-2";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS850_HSI_PIN_DRV_LV2>;
+	};
+
+	sd2_bus4_pins: sd2-bus4-pins {
+		samsung,pins = "gpf2-3", "gpf2-4", "gpf2-5";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS850_HSI_PIN_DRV_LV2>;
+	};
+
+	sd2_pdn_pins: sd2-pdn-pins {
+		samsung,pins = "gpf2-0", "gpf2-1", "gpf2-2", "gpf2-3",
+			       "gpf2-4", "gpf2-5";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+	};
+};
+
+&pinctrl_core {
+	gpf0: gpf0-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpf1: gpf1-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	sd0_clk_pins: sd0-clk-pins {
+		samsung,pins = "gpf0-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
+	};
+
+	sd0_cmd_pins: sd0-cmd-pins {
+		samsung,pins = "gpf0-1";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
+	};
+
+	sd0_rdqs_pins: sd0-rdqs-pins {
+		samsung,pins = "gpf0-2";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
+	};
+
+	sd0_nreset_pins: sd0-nreset-pins {
+		samsung,pins = "gpf0-3";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
+	};
+
+	sd0_bus1_pins: sd0-bus1-pins {
+		samsung,pins = "gpf1-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
+	};
+
+	sd0_bus4_pins: sd0-bus4-pins {
+		samsung,pins = "gpf1-1", "gpf1-2", "gpf1-3";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
+	};
+
+	sd0_bus8_pins: sd0-bus8-pins {
+		samsung,pins = "gpf1-4", "gpf1-5", "gpf1-6", "gpf1-7";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV4>;
+	};
+};
+
+&pinctrl_peri {
+	gpc0: gpc0-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpc1: gpc1-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpg0: gpg0-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpg1: gpg1-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpg2: gpg2-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpg3: gpg3-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpp0: gpp0-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+	gpp1: gpp1-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpp2: gpp2-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	sensor_mclk0_in_pins: sensor-mclk0-in-pins {
+		samsung,pins = "gpc0-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
+	};
+
+	sensor_mclk0_out_pins: sensor-mclk0-out-pins {
+		samsung,pins = "gpc0-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
+	};
+
+	sensor_mclk0_fn_pins: sensor-mclk0-fn-pins {
+		samsung,pins = "gpc0-0";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
+	};
+
+	sensor_mclk1_in_pins: sensor-mclk1-in-pins {
+		samsung,pins = "gpc0-1";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
+	};
+
+	sensor_mclk1_out_pins: sensor-mclk1-out-pins {
+		samsung,pins = "gpc0-1";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
+	};
+
+	sensor_mclk1_fn_pins: sensor-mclk1-fn-pins {
+		samsung,pins = "gpc0-1";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
+	};
+
+	sensor_mclk2_in_pins: sensor-mclk2-in-pins {
+		samsung,pins = "gpc0-2";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
+	};
+
+	sensor_mclk2_out_pins: sensor-mclk2-out-pins {
+		samsung,pins = "gpc0-2";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
+	};
+
+	sensor_mclk2_fn_pins: sensor-mclk2-fn-pins {
+		samsung,pins = "gpc0-2";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV3>;
+	};
+
+	/* USI: HSI2C0 */
+	hsi2c0_pins: hsi2c0-pins {
+		samsung,pins = "gpc1-0", "gpc1-1";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
+
+	/* USI: HSI2C1 */
+	hsi2c1_pins: hsi2c1-pins {
+		samsung,pins = "gpc1-2", "gpc1-3";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
+
+	/* USI: HSI2C2 */
+	hsi2c2_pins: hsi2c2-pins {
+		samsung,pins = "gpc1-4", "gpc1-5";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
+
+	/* USI: SPI */
+	spi0_pins: spi0-pins {
+		samsung,pins = "gpp2-0", "gpp2-1", "gpp2-2", "gpp2-3";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
+
+	i2c0_pins: i2c0-pins {
+		samsung,pins = "gpp0-0", "gpp0-1";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
+
+	i2c1_pins: i2c1-pins {
+		samsung,pins = "gpp0-2", "gpp0-3";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
+
+	i2c2_pins: i2c2-pins {
+		samsung,pins = "gpp0-4", "gpp0-5";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
+
+	i2c3_pins: i2c3-pins {
+		samsung,pins = "gpp1-0", "gpp1-1";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
+
+	i2c4_pins: i2c4-pins {
+		samsung,pins = "gpp1-2", "gpp1-3";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_UP>;
+		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
+	};
+
+	xclkout_pins: xclkout-pins {
+		samsung,pins = "gpq0-2";
+		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
+		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
+	};
+};
diff --git a/arch/arm64/boot/dts/exynos/exynos850.dtsi b/arch/arm64/boot/dts/exynos/exynos850.dtsi
new file mode 100644
index 000000000000..c61441f3a89a
--- /dev/null
+++ b/arch/arm64/boot/dts/exynos/exynos850.dtsi
@@ -0,0 +1,769 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Samsung Exynos850 SoC device tree source
+ *
+ * Copyright (C) 2018 Samsung Electronics Co., Ltd.
+ * Copyright (C) 2021 Linaro Ltd.
+ *
+ * Samsung Exynos850 SoC device nodes are listed in this file.
+ * Exynos850 based board files can include this file and provide
+ * values for board specific bindings.
+ */
+
+#include <dt-bindings/clock/exynos850.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/soc/samsung,exynos-usi.h>
+
+/ {
+	/* Also known under engineering name Exynos3830 */
+	compatible = "samsung,exynos850";
+	#address-cells = <2>;
+	#size-cells = <1>;
+
+	interrupt-parent = <&gic>;
+
+	aliases {
+		pinctrl0 = &pinctrl_alive;
+		pinctrl1 = &pinctrl_cmgp;
+		pinctrl2 = &pinctrl_aud;
+		pinctrl3 = &pinctrl_hsi;
+		pinctrl4 = &pinctrl_core;
+		pinctrl5 = &pinctrl_peri;
+	};
+
+	arm-pmu {
+		compatible = "arm,cortex-a55-pmu";
+		interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>,
+				     <&cpu4>, <&cpu5>, <&cpu6>, <&cpu7>;
+	};
+
+	/* Main system clock (XTCXO); external, must be 26 MHz */
+	oscclk: clock-oscclk {
+		compatible = "fixed-clock";
+		clock-output-names = "oscclk";
+		#clock-cells = <0>;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu-map {
+			cluster0 {
+				core0 {
+					cpu = <&cpu0>;
+				};
+				core1 {
+					cpu = <&cpu1>;
+				};
+				core2 {
+					cpu = <&cpu2>;
+				};
+				core3 {
+					cpu = <&cpu3>;
+				};
+			};
+
+			cluster1 {
+				core0 {
+					cpu = <&cpu4>;
+				};
+				core1 {
+					cpu = <&cpu5>;
+				};
+				core2 {
+					cpu = <&cpu6>;
+				};
+				core3 {
+					cpu = <&cpu7>;
+				};
+			};
+		};
+
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a55";
+			reg = <0x0>;
+			enable-method = "psci";
+		};
+		cpu1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a55";
+			reg = <0x1>;
+			enable-method = "psci";
+		};
+		cpu2: cpu@2 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a55";
+			reg = <0x2>;
+			enable-method = "psci";
+		};
+		cpu3: cpu@3 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a55";
+			reg = <0x3>;
+			enable-method = "psci";
+		};
+		cpu4: cpu@100 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a55";
+			reg = <0x100>;
+			enable-method = "psci";
+		};
+		cpu5: cpu@101 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a55";
+			reg = <0x101>;
+			enable-method = "psci";
+		};
+		cpu6: cpu@102 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a55";
+			reg = <0x102>;
+			enable-method = "psci";
+		};
+		cpu7: cpu@103 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a55";
+			reg = <0x103>;
+			enable-method = "psci";
+		};
+	};
+
+	psci {
+		compatible = "arm,psci-1.0";
+		method = "smc";
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		/* Hypervisor Virtual Timer interrupt is not wired to GIC */
+		interrupts =
+		     <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
+		     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
+		     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
+		     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>;
+	};
+
+	soc: soc@0 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x0 0x0 0x20000000>;
+
+		chipid@10000000 {
+			compatible = "samsung,exynos850-chipid";
+			reg = <0x10000000 0x100>;
+		};
+
+		timer@10040000 {
+			compatible = "samsung,exynos850-mct",
+				     "samsung,exynos4210-mct";
+			reg = <0x10040000 0x800>;
+			interrupts = <GIC_SPI 203 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 204 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 205 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 206 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 210 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 211 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 212 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 213 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 214 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&oscclk>, <&cmu_peri CLK_GOUT_MCT_PCLK>;
+			clock-names = "fin_pll", "mct";
+		};
+
+		gic: interrupt-controller@12a01000 {
+			compatible = "arm,gic-400";
+			#interrupt-cells = <3>;
+			#address-cells = <0>;
+			reg = <0x12a01000 0x1000>,
+			      <0x12a02000 0x2000>,
+			      <0x12a04000 0x2000>,
+			      <0x12a06000 0x2000>;
+			interrupt-controller;
+			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(8) |
+						 IRQ_TYPE_LEVEL_HIGH)>;
+		};
+
+		pmu_system_controller: system-controller@11860000 {
+			compatible = "samsung,exynos850-pmu", "syscon";
+			reg = <0x11860000 0x10000>;
+			clocks = <&cmu_apm CLK_GOUT_PMU_ALIVE_PCLK>;
+
+			reboot: syscon-reboot {
+				compatible = "syscon-reboot";
+				regmap = <&pmu_system_controller>;
+				offset = <0x3a00>; /* SYSTEM_CONFIGURATION */
+				mask = <0x2>; /* SWRESET_SYSTEM */
+				value = <0x2>; /* reset value */
+			};
+		};
+
+		watchdog_cl0: watchdog@10050000 {
+			compatible = "samsung,exynos850-wdt";
+			reg = <0x10050000 0x100>;
+			interrupts = <GIC_SPI 228 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cmu_peri CLK_GOUT_WDT0_PCLK>, <&oscclk>;
+			clock-names = "watchdog", "watchdog_src";
+			samsung,syscon-phandle = <&pmu_system_controller>;
+			samsung,cluster-index = <0>;
+			status = "disabled";
+		};
+
+		watchdog_cl1: watchdog@10060000 {
+			compatible = "samsung,exynos850-wdt";
+			reg = <0x10060000 0x100>;
+			interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cmu_peri CLK_GOUT_WDT1_PCLK>, <&oscclk>;
+			clock-names = "watchdog", "watchdog_src";
+			samsung,syscon-phandle = <&pmu_system_controller>;
+			samsung,cluster-index = <1>;
+			status = "disabled";
+		};
+
+		cmu_peri: clock-controller@10030000 {
+			compatible = "samsung,exynos850-cmu-peri";
+			reg = <0x10030000 0x8000>;
+			#clock-cells = <1>;
+
+			clocks = <&oscclk>, <&cmu_top CLK_DOUT_PERI_BUS>,
+				 <&cmu_top CLK_DOUT_PERI_UART>,
+				 <&cmu_top CLK_DOUT_PERI_IP>;
+			clock-names = "oscclk", "dout_peri_bus",
+				      "dout_peri_uart", "dout_peri_ip";
+		};
+
+		cmu_apm: clock-controller@11800000 {
+			compatible = "samsung,exynos850-cmu-apm";
+			reg = <0x11800000 0x8000>;
+			#clock-cells = <1>;
+
+			clocks = <&oscclk>, <&cmu_top CLK_DOUT_CLKCMU_APM_BUS>;
+			clock-names = "oscclk", "dout_clkcmu_apm_bus";
+		};
+
+		cmu_cmgp: clock-controller@11c00000 {
+			compatible = "samsung,exynos850-cmu-cmgp";
+			reg = <0x11c00000 0x8000>;
+			#clock-cells = <1>;
+
+			clocks = <&oscclk>, <&cmu_apm CLK_GOUT_CLKCMU_CMGP_BUS>;
+			clock-names = "oscclk", "gout_clkcmu_cmgp_bus";
+		};
+
+		cmu_core: clock-controller@12000000 {
+			compatible = "samsung,exynos850-cmu-core";
+			reg = <0x12000000 0x8000>;
+			#clock-cells = <1>;
+
+			clocks = <&oscclk>, <&cmu_top CLK_DOUT_CORE_BUS>,
+				 <&cmu_top CLK_DOUT_CORE_CCI>,
+				 <&cmu_top CLK_DOUT_CORE_MMC_EMBD>,
+				 <&cmu_top CLK_DOUT_CORE_SSS>;
+			clock-names = "oscclk", "dout_core_bus",
+				      "dout_core_cci", "dout_core_mmc_embd",
+				      "dout_core_sss";
+		};
+
+		cmu_top: clock-controller@120e0000 {
+			compatible = "samsung,exynos850-cmu-top";
+			reg = <0x120e0000 0x8000>;
+			#clock-cells = <1>;
+
+			clocks = <&oscclk>;
+			clock-names = "oscclk";
+		};
+
+		cmu_mfcmscl: clock-controller@12c00000 {
+			compatible = "samsung,exynos850-cmu-mfcmscl";
+			reg = <0x12c00000 0x8000>;
+			#clock-cells = <1>;
+
+			clocks = <&oscclk>,
+				 <&cmu_top CLK_DOUT_MFCMSCL_MFC>,
+				 <&cmu_top CLK_DOUT_MFCMSCL_M2M>,
+				 <&cmu_top CLK_DOUT_MFCMSCL_MCSC>,
+				 <&cmu_top CLK_DOUT_MFCMSCL_JPEG>;
+			clock-names = "oscclk", "dout_mfcmscl_mfc",
+				      "dout_mfcmscl_m2m", "dout_mfcmscl_mcsc",
+				      "dout_mfcmscl_jpeg";
+		};
+
+		cmu_dpu: clock-controller@13000000 {
+			compatible = "samsung,exynos850-cmu-dpu";
+			reg = <0x13000000 0x8000>;
+			#clock-cells = <1>;
+
+			clocks = <&oscclk>, <&cmu_top CLK_DOUT_DPU>;
+			clock-names = "oscclk", "dout_dpu";
+		};
+
+		cmu_hsi: clock-controller@13400000 {
+			compatible = "samsung,exynos850-cmu-hsi";
+			reg = <0x13400000 0x8000>;
+			#clock-cells = <1>;
+
+			clocks = <&oscclk>,
+				 <&cmu_top CLK_DOUT_HSI_BUS>,
+				 <&cmu_top CLK_DOUT_HSI_MMC_CARD>,
+				 <&cmu_top CLK_DOUT_HSI_USB20DRD>;
+			clock-names = "oscclk", "dout_hsi_bus",
+				      "dout_hsi_mmc_card", "dout_hsi_usb20drd";
+		};
+
+		cmu_is: clock-controller@14500000 {
+			compatible = "samsung,exynos850-cmu-is";
+			reg = <0x14500000 0x8000>;
+			#clock-cells = <1>;
+
+			clocks = <&oscclk>,
+				 <&cmu_top CLK_DOUT_IS_BUS>,
+				 <&cmu_top CLK_DOUT_IS_ITP>,
+				 <&cmu_top CLK_DOUT_IS_VRA>,
+				 <&cmu_top CLK_DOUT_IS_GDC>;
+			clock-names = "oscclk", "dout_is_bus", "dout_is_itp",
+				      "dout_is_vra", "dout_is_gdc";
+		};
+
+		cmu_aud: clock-controller@14a00000 {
+			compatible = "samsung,exynos850-cmu-aud";
+			reg = <0x14a00000 0x8000>;
+			#clock-cells = <1>;
+
+			clocks = <&oscclk>, <&cmu_top CLK_DOUT_AUD>;
+			clock-names = "oscclk", "dout_aud";
+		};
+
+		pinctrl_alive: pinctrl@11850000 {
+			compatible = "samsung,exynos850-pinctrl";
+			reg = <0x11850000 0x1000>;
+
+			wakeup-interrupt-controller {
+				compatible = "samsung,exynos850-wakeup-eint";
+			};
+		};
+
+		pinctrl_cmgp: pinctrl@11c30000 {
+			compatible = "samsung,exynos850-pinctrl";
+			reg = <0x11c30000 0x1000>;
+
+			wakeup-interrupt-controller {
+				compatible = "samsung,exynos850-wakeup-eint";
+			};
+		};
+
+		pinctrl_core: pinctrl@12070000 {
+			compatible = "samsung,exynos850-pinctrl";
+			reg = <0x12070000 0x1000>;
+			interrupts = <GIC_SPI 451 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		pinctrl_hsi: pinctrl@13430000 {
+			compatible = "samsung,exynos850-pinctrl";
+			reg = <0x13430000 0x1000>;
+			interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		pinctrl_peri: pinctrl@139b0000 {
+			compatible = "samsung,exynos850-pinctrl";
+			reg = <0x139b0000 0x1000>;
+			interrupts = <GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		pinctrl_aud: pinctrl@14a60000 {
+			compatible = "samsung,exynos850-pinctrl";
+			reg = <0x14a60000 0x1000>;
+		};
+
+		rtc: rtc@11a30000 {
+			compatible = "samsung,s3c6410-rtc";
+			reg = <0x11a30000 0x100>;
+			interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cmu_apm CLK_GOUT_RTC_PCLK>;
+			clock-names = "rtc";
+			status = "disabled";
+		};
+
+		mmc_0: mmc@12100000 {
+			compatible = "samsung,exynos7-dw-mshc-smu";
+			reg = <0x12100000 0x2000>;
+			interrupts = <GIC_SPI 452 IRQ_TYPE_LEVEL_HIGH>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			clocks = <&cmu_core CLK_GOUT_MMC_EMBD_ACLK>,
+				 <&cmu_core CLK_GOUT_MMC_EMBD_SDCLKIN>;
+			clock-names = "biu", "ciu";
+			fifo-depth = <0x40>;
+			status = "disabled";
+		};
+
+		i2c_0: i2c@13830000 {
+			compatible = "samsung,s3c2440-i2c";
+			reg = <0x13830000 0x100>;
+			interrupts = <GIC_SPI 196 IRQ_TYPE_LEVEL_HIGH>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&i2c0_pins>;
+			clocks = <&cmu_peri CLK_GOUT_I2C0_PCLK>;
+			clock-names = "i2c";
+			status = "disabled";
+		};
+
+		i2c_1: i2c@13840000 {
+			compatible = "samsung,s3c2440-i2c";
+			reg = <0x13840000 0x100>;
+			interrupts = <GIC_SPI 197 IRQ_TYPE_LEVEL_HIGH>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&i2c1_pins>;
+			clocks = <&cmu_peri CLK_GOUT_I2C1_PCLK>;
+			clock-names = "i2c";
+			status = "disabled";
+		};
+
+		i2c_2: i2c@13850000 {
+			compatible = "samsung,s3c2440-i2c";
+			reg = <0x13850000 0x100>;
+			interrupts = <GIC_SPI 198 IRQ_TYPE_LEVEL_HIGH>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&i2c2_pins>;
+			clocks = <&cmu_peri CLK_GOUT_I2C2_PCLK>;
+			clock-names = "i2c";
+			status = "disabled";
+		};
+
+		i2c_3: i2c@13860000 {
+			compatible = "samsung,s3c2440-i2c";
+			reg = <0x13860000 0x100>;
+			interrupts = <GIC_SPI 199 IRQ_TYPE_LEVEL_HIGH>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&i2c3_pins>;
+			clocks = <&cmu_peri CLK_GOUT_I2C3_PCLK>;
+			clock-names = "i2c";
+			status = "disabled";
+		};
+
+		i2c_4: i2c@13870000 {
+			compatible = "samsung,s3c2440-i2c";
+			reg = <0x13870000 0x100>;
+			interrupts = <GIC_SPI 200 IRQ_TYPE_LEVEL_HIGH>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&i2c4_pins>;
+			clocks = <&cmu_peri CLK_GOUT_I2C4_PCLK>;
+			clock-names = "i2c";
+			status = "disabled";
+		};
+
+		/* I2C_5 (also called CAM_PMIC_I2C in TRM) */
+		i2c_5: i2c@13880000 {
+			compatible = "samsung,s3c2440-i2c";
+			reg = <0x13880000 0x100>;
+			interrupts = <GIC_SPI 201 IRQ_TYPE_LEVEL_HIGH>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&i2c5_pins>;
+			clocks = <&cmu_peri CLK_GOUT_I2C5_PCLK>;
+			clock-names = "i2c";
+			status = "disabled";
+		};
+
+		/* I2C_6 (also called MOTOR_I2C in TRM) */
+		i2c_6: i2c@13890000 {
+			compatible = "samsung,s3c2440-i2c";
+			reg = <0x13890000 0x100>;
+			interrupts = <GIC_SPI 202 IRQ_TYPE_LEVEL_HIGH>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&i2c6_pins>;
+			clocks = <&cmu_peri CLK_GOUT_I2C6_PCLK>;
+			clock-names = "i2c";
+			status = "disabled";
+		};
+
+		sysmmu_mfcmscl: sysmmu@12c50000 {
+			compatible = "samsung,exynos-sysmmu";
+			reg = <0x12c50000 0x9000>;
+			interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>;
+			clock-names = "sysmmu";
+			clocks = <&cmu_mfcmscl CLK_GOUT_MFCMSCL_SYSMMU_CLK>;
+			#iommu-cells = <0>;
+		};
+
+		sysmmu_dpu: sysmmu@130c0000 {
+			compatible = "samsung,exynos-sysmmu";
+			reg = <0x130c0000 0x9000>;
+			interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>;
+			clock-names = "sysmmu";
+			clocks = <&cmu_dpu CLK_GOUT_DPU_SMMU_CLK>;
+			#iommu-cells = <0>;
+		};
+
+		sysmmu_is0: sysmmu@14550000 {
+			compatible = "samsung,exynos-sysmmu";
+			reg = <0x14550000 0x9000>;
+			interrupts = <GIC_SPI 164 IRQ_TYPE_LEVEL_HIGH>;
+			clock-names = "sysmmu";
+			clocks = <&cmu_is CLK_GOUT_IS_SYSMMU_IS0_CLK>;
+			#iommu-cells = <0>;
+		};
+
+		sysmmu_is1: sysmmu@14570000 {
+			compatible = "samsung,exynos-sysmmu";
+			reg = <0x14570000 0x9000>;
+			interrupts = <GIC_SPI 166 IRQ_TYPE_LEVEL_HIGH>;
+			clock-names = "sysmmu";
+			clocks = <&cmu_is CLK_GOUT_IS_SYSMMU_IS1_CLK>;
+			#iommu-cells = <0>;
+		};
+
+		sysmmu_aud: sysmmu@14850000 {
+			compatible = "samsung,exynos-sysmmu";
+			reg = <0x14850000 0x9000>;
+			interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>;
+			clock-names = "sysmmu";
+			clocks = <&cmu_aud CLK_GOUT_AUD_SYSMMU_CLK>;
+			#iommu-cells = <0>;
+		};
+
+		sysreg_peri: syscon@10020000 {
+			compatible = "samsung,exynos850-sysreg", "syscon";
+			reg = <0x10020000 0x10000>;
+			clocks = <&cmu_peri CLK_GOUT_SYSREG_PERI_PCLK>;
+		};
+
+		sysreg_cmgp: syscon@11c20000 {
+			compatible = "samsung,exynos850-sysreg", "syscon";
+			reg = <0x11c20000 0x10000>;
+			clocks = <&cmu_cmgp CLK_GOUT_SYSREG_CMGP_PCLK>;
+		};
+
+		usi_uart: usi@138200c0 {
+			compatible = "samsung,exynos850-usi";
+			reg = <0x138200c0 0x20>;
+			samsung,sysreg = <&sysreg_peri 0x1010>;
+			samsung,mode = <USI_V2_UART>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			clocks = <&cmu_peri CLK_GOUT_UART_PCLK>,
+				 <&cmu_peri CLK_GOUT_UART_IPCLK>;
+			clock-names = "pclk", "ipclk";
+			status = "disabled";
+
+			serial_0: serial@13820000 {
+				compatible = "samsung,exynos850-uart";
+				reg = <0x13820000 0xc0>;
+				interrupts = <GIC_SPI 227 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&uart0_pins>;
+				clocks = <&cmu_peri CLK_GOUT_UART_PCLK>,
+					 <&cmu_peri CLK_GOUT_UART_IPCLK>;
+				clock-names = "uart", "clk_uart_baud0";
+				status = "disabled";
+			};
+		};
+
+		usi_hsi2c_0: usi@138a00c0 {
+			compatible = "samsung,exynos850-usi";
+			reg = <0x138a00c0 0x20>;
+			samsung,sysreg = <&sysreg_peri 0x1020>;
+			samsung,mode = <USI_V2_I2C>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			clocks = <&cmu_peri CLK_GOUT_HSI2C0_PCLK>,
+				 <&cmu_peri CLK_GOUT_HSI2C0_IPCLK>;
+			clock-names = "pclk", "ipclk";
+			status = "disabled";
+
+			hsi2c_0: i2c@138a0000 {
+				compatible = "samsung,exynosautov9-hsi2c";
+				reg = <0x138a0000 0xc0>;
+				interrupts = <GIC_SPI 193 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&hsi2c0_pins>;
+				clocks = <&cmu_peri CLK_GOUT_HSI2C0_IPCLK>,
+					 <&cmu_peri CLK_GOUT_HSI2C0_PCLK>;
+				clock-names = "hsi2c", "hsi2c_pclk";
+				status = "disabled";
+			};
+		};
+
+		usi_hsi2c_1: usi@138b00c0 {
+			compatible = "samsung,exynos850-usi";
+			reg = <0x138b00c0 0x20>;
+			samsung,sysreg = <&sysreg_peri 0x1030>;
+			samsung,mode = <USI_V2_I2C>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			clocks = <&cmu_peri CLK_GOUT_HSI2C1_PCLK>,
+				 <&cmu_peri CLK_GOUT_HSI2C1_IPCLK>;
+			clock-names = "pclk", "ipclk";
+			status = "disabled";
+
+			hsi2c_1: i2c@138b0000 {
+				compatible = "samsung,exynosautov9-hsi2c";
+				reg = <0x138b0000 0xc0>;
+				interrupts = <GIC_SPI 194 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&hsi2c1_pins>;
+				clocks = <&cmu_peri CLK_GOUT_HSI2C1_IPCLK>,
+					 <&cmu_peri CLK_GOUT_HSI2C1_PCLK>;
+				clock-names = "hsi2c", "hsi2c_pclk";
+				status = "disabled";
+			};
+		};
+
+		usi_hsi2c_2: usi@138c00c0 {
+			compatible = "samsung,exynos850-usi";
+			reg = <0x138c00c0 0x20>;
+			samsung,sysreg = <&sysreg_peri 0x1040>;
+			samsung,mode = <USI_V2_I2C>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			clocks = <&cmu_peri CLK_GOUT_HSI2C2_PCLK>,
+				 <&cmu_peri CLK_GOUT_HSI2C2_IPCLK>;
+			clock-names = "pclk", "ipclk";
+			status = "disabled";
+
+			hsi2c_2: i2c@138c0000 {
+				compatible = "samsung,exynosautov9-hsi2c";
+				reg = <0x138c0000 0xc0>;
+				interrupts = <GIC_SPI 195 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&hsi2c2_pins>;
+				clocks = <&cmu_peri CLK_GOUT_HSI2C2_IPCLK>,
+					 <&cmu_peri CLK_GOUT_HSI2C2_PCLK>;
+				clock-names = "hsi2c", "hsi2c_pclk";
+				status = "disabled";
+			};
+		};
+
+		usi_spi_0: usi@139400c0 {
+			compatible = "samsung,exynos850-usi";
+			reg = <0x139400c0 0x20>;
+			samsung,sysreg = <&sysreg_peri 0x1050>;
+			samsung,mode = <USI_V2_SPI>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			clocks = <&cmu_peri CLK_GOUT_SPI0_PCLK>,
+				 <&cmu_peri CLK_GOUT_SPI0_IPCLK>;
+			clock-names = "pclk", "ipclk";
+			status = "disabled";
+		};
+
+		usi_cmgp0: usi@11d000c0 {
+			compatible = "samsung,exynos850-usi";
+			reg = <0x11d000c0 0x20>;
+			samsung,sysreg = <&sysreg_cmgp 0x2000>;
+			samsung,mode = <USI_V2_I2C>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			clocks = <&cmu_cmgp CLK_GOUT_CMGP_USI0_PCLK>,
+				 <&cmu_cmgp CLK_GOUT_CMGP_USI0_IPCLK>;
+			clock-names = "pclk", "ipclk";
+			status = "disabled";
+
+			hsi2c_3: i2c@11d00000 {
+				compatible = "samsung,exynosautov9-hsi2c";
+				reg = <0x11d00000 0xc0>;
+				interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&hsi2c3_pins>;
+				clocks = <&cmu_cmgp CLK_GOUT_CMGP_USI0_IPCLK>,
+					 <&cmu_cmgp CLK_GOUT_CMGP_USI0_PCLK>;
+				clock-names = "hsi2c", "hsi2c_pclk";
+				status = "disabled";
+			};
+
+			serial_1: serial@11d00000 {
+				compatible = "samsung,exynos850-uart";
+				reg = <0x11d00000 0xc0>;
+				interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&uart1_single_pins>;
+				clocks = <&cmu_cmgp CLK_GOUT_CMGP_USI0_PCLK>,
+					 <&cmu_cmgp CLK_GOUT_CMGP_USI0_IPCLK>;
+				clock-names = "uart", "clk_uart_baud0";
+				status = "disabled";
+			};
+		};
+
+		usi_cmgp1: usi@11d200c0 {
+			compatible = "samsung,exynos850-usi";
+			reg = <0x11d200c0 0x20>;
+			samsung,sysreg = <&sysreg_cmgp 0x2010>;
+			samsung,mode = <USI_V2_I2C>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			clocks = <&cmu_cmgp CLK_GOUT_CMGP_USI1_PCLK>,
+				 <&cmu_cmgp CLK_GOUT_CMGP_USI1_IPCLK>;
+			clock-names = "pclk", "ipclk";
+			status = "disabled";
+
+			hsi2c_4: i2c@11d20000 {
+				compatible = "samsung,exynosautov9-hsi2c";
+				reg = <0x11d20000 0xc0>;
+				interrupts = <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&hsi2c4_pins>;
+				clocks = <&cmu_cmgp CLK_GOUT_CMGP_USI1_IPCLK>,
+					 <&cmu_cmgp CLK_GOUT_CMGP_USI1_PCLK>;
+				clock-names = "hsi2c", "hsi2c_pclk";
+				status = "disabled";
+			};
+
+			serial_2: serial@11d20000 {
+				compatible = "samsung,exynos850-uart";
+				reg = <0x11d20000 0xc0>;
+				interrupts = <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&uart2_single_pins>;
+				clocks = <&cmu_cmgp CLK_GOUT_CMGP_USI1_PCLK>,
+					 <&cmu_cmgp CLK_GOUT_CMGP_USI1_IPCLK>;
+				clock-names = "uart", "clk_uart_baud0";
+				status = "disabled";
+			};
+		};
+	};
+};
+
+#include "exynos850-pinctrl.dtsi"
diff --git a/arch/arm64/boot/dts/exynos/exynosautov9-pinctrl.dtsi b/arch/arm64/boot/dts/exynos/exynosautov9-pinctrl.dtsi
index 2407b03b5404..e413a51c2d08 100644
--- a/arch/arm64/boot/dts/exynos/exynosautov9-pinctrl.dtsi
+++ b/arch/arm64/boot/dts/exynos/exynosautov9-pinctrl.dtsi
@@ -8,10 +8,10 @@
  * device tree nodes in this file.
  */
 
-#include <dt-bindings/pinctrl/samsung.h>
+#include "exynos-pinctrl.h"
 
 &pinctrl_alive {
-	gpa0: gpa0 {
+	gpa0: gpa0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 		interrupt-controller;
@@ -27,7 +27,7 @@
 			     <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
 	};
 
-	gpa1: gpa1 {
+	gpa1: gpa1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 		interrupt-controller;
@@ -47,7 +47,7 @@
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 	};
 
-	gpq0: gpq0 {
+	gpq0: gpq0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -69,7 +69,7 @@
 };
 
 &pinctrl_aud {
-	gpb0: gpb0 {
+	gpb0: gpb0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -77,7 +77,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpb1: gpb1 {
+	gpb1: gpb1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -85,7 +85,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpb2: gpb2 {
+	gpb2: gpb2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -93,7 +93,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpb3: gpb3 {
+	gpb3: gpb3-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -199,7 +199,7 @@
 };
 
 &pinctrl_fsys0 {
-	gpf0: gpf0 {
+	gpf0: gpf0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -207,7 +207,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpf1: gpf1 {
+	gpf1: gpf1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -355,7 +355,7 @@
 };
 
 &pinctrl_fsys1 {
-	gpf8: gpf8 {
+	gpf8: gpf8-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -393,7 +393,7 @@
 };
 
 &pinctrl_fsys2 {
-	gpf2: gpf2 {
+	gpf2: gpf2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -401,7 +401,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpf3: gpf3 {
+	gpf3: gpf3-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -409,7 +409,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpf4: gpf4 {
+	gpf4: gpf4-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -417,7 +417,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpf5: gpf5 {
+	gpf5: gpf5-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -425,7 +425,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpf6: gpf6 {
+	gpf6: gpf6-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -499,7 +499,7 @@
 };
 
 &pinctrl_peric0 {
-	gpp0: gpp0 {
+	gpp0: gpp0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -507,7 +507,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpp1: gpp1 {
+	gpp1: gpp1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -515,7 +515,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpp2: gpp2 {
+	gpp2: gpp2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -523,7 +523,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpg0: gpg0 {
+	gpg0: gpg0-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -833,7 +833,7 @@
 };
 
 &pinctrl_peric1 {
-	gpp3: gpp3 {
+	gpp3: gpp3-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -841,7 +841,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpp4: gpp4 {
+	gpp4: gpp4-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -849,7 +849,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpp5: gpp5 {
+	gpp5: gpp5-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -857,7 +857,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpg1: gpg1 {
+	gpg1: gpg1-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -865,7 +865,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpg2: gpg2 {
+	gpg2: gpg2-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -873,7 +873,7 @@
 		#interrupt-cells = <2>;
 	};
 
-	gpg3: gpg3 {
+	gpg3: gpg3-gpio-bank {
 		gpio-controller;
 		#gpio-cells = <2>;
 
@@ -1089,21 +1089,21 @@
 
 	/* PERIC1 USI11_SPI */
 	spi11_bus: spi11-pins {
-		samsung,pins = "gpp3-6", "gpp3-5", "gpp3-4";
+		samsung,pins = "gpp5-6", "gpp5-5", "gpp5-4";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
 	spi11_cs: spi11-cs-pins {
-		samsung,pins = "gpp3-7";
+		samsung,pins = "gpp5-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
 	};
 
 	spi11_cs_func: spi11-cs-func-pins {
-		samsung,pins = "gpp3-7";
+		samsung,pins = "gpp5-7";
 		samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 		samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 		samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
diff --git a/arch/arm64/boot/dts/exynos/exynosautov9-sadk.dts b/arch/arm64/boot/dts/exynos/exynosautov9-sadk.dts
index ef46d7aa6e28..eec3192c0631 100644
--- a/arch/arm64/boot/dts/exynos/exynosautov9-sadk.dts
+++ b/arch/arm64/boot/dts/exynos/exynosautov9-sadk.dts
@@ -39,9 +39,18 @@
 		regulator-boot-on;
 		enable-active-high;
 	};
+
+	ufs_1_fixed_vcc_reg: regulator-1 {
+		compatible = "regulator-fixed";
+		regulator-name = "ufs-vcc";
+		gpio = <&gpg2 2 GPIO_ACTIVE_HIGH>;
+		regulator-boot-on;
+		enable-active-high;
+	};
 };
 
 &serial_0 {
+	pinctrl-0 = <&uart0_bus_dual>;
 	status = "okay";
 };
 
@@ -49,8 +58,27 @@
 	status = "okay";
 };
 
+&ufs_1_phy {
+	status = "okay";
+};
+
 &ufs_0 {
 	status = "okay";
 	vcc-supply = <&ufs_0_fixed_vcc_reg>;
 	vcc-fixed-regulator;
 };
+
+&ufs_1 {
+	status = "okay";
+	vcc-supply = <&ufs_1_fixed_vcc_reg>;
+	vcc-fixed-regulator;
+};
+
+&usi_0 {
+	samsung,clkreq-on; /* needed for UART mode */
+	status = "okay";
+};
+
+&xtcxo {
+	clock-frequency = <26000000>;
+};
diff --git a/arch/arm64/boot/dts/exynos/exynosautov9.dtsi b/arch/arm64/boot/dts/exynos/exynosautov9.dtsi
index a960c0bc2dba..5dc361734cfe 100644
--- a/arch/arm64/boot/dts/exynos/exynosautov9.dtsi
+++ b/arch/arm64/boot/dts/exynos/exynosautov9.dtsi
@@ -6,7 +6,10 @@
  *
  */
 
+#include <dt-bindings/clock/samsung,exynosautov9.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/soc/samsung,boot-mode.h>
+#include <dt-bindings/soc/samsung,exynos-usi.h>
 
 / {
 	compatible = "samsung,exynosautov9";
@@ -152,30 +155,8 @@
 		xtcxo: clock {
 			compatible = "fixed-clock";
 			#clock-cells = <0>;
-			clock-frequency = <26000000>;
 			clock-output-names = "oscclk";
 		};
-
-		/*
-		 * Keep the stub clock for serial driver, until proper clock
-		 * driver is implemented.
-		 */
-		uart_clock: uart-clock {
-			compatible = "fixed-clock";
-			#clock-cells = <0>;
-			clock-frequency = <133250000>;
-			clock-output-names = "uart";
-		};
-
-		/*
-		 * Keep the stub clock for ufs driver, until proper clock
-		 * driver is implemented.
-		 */
-		ufs_core_clock: ufs-core-clock {
-			compatible = "fixed-clock";
-			#clock-cells = <0>;
-			clock-frequency = <166562500>;
-		};
 	};
 
 	soc: soc@0 {
@@ -189,6 +170,117 @@
 			reg = <0x10000000 0x24>;
 		};
 
+		cmu_peris: clock-controller@10020000 {
+			compatible = "samsung,exynosautov9-cmu-peris";
+			reg = <0x10020000 0x8000>;
+			#clock-cells = <1>;
+
+			clocks = <&xtcxo>,
+				 <&cmu_top DOUT_CLKCMU_PERIS_BUS>;
+			clock-names = "oscclk",
+				      "dout_clkcmu_peris_bus";
+		};
+
+		cmu_peric0: clock-controller@10200000 {
+			compatible = "samsung,exynosautov9-cmu-peric0";
+			reg = <0x10200000 0x8000>;
+			#clock-cells = <1>;
+
+			clocks = <&xtcxo>,
+				 <&cmu_top DOUT_CLKCMU_PERIC0_BUS>,
+				 <&cmu_top DOUT_CLKCMU_PERIC0_IP>;
+			clock-names = "oscclk",
+				      "dout_clkcmu_peric0_bus",
+				      "dout_clkcmu_peric0_ip";
+		};
+
+		cmu_peric1: clock-controller@10800000 {
+			compatible = "samsung,exynosautov9-cmu-peric1";
+			reg = <0x10800000 0x8000>;
+			#clock-cells = <1>;
+
+			clocks = <&xtcxo>,
+				 <&cmu_top DOUT_CLKCMU_PERIC1_BUS>,
+				 <&cmu_top DOUT_CLKCMU_PERIC1_IP>;
+			clock-names = "oscclk",
+				      "dout_clkcmu_peric1_bus",
+				      "dout_clkcmu_peric1_ip";
+		};
+
+		cmu_fsys1: clock-controller@17040000 {
+			compatible = "samsung,exynosautov9-cmu-fsys1";
+			reg = <0x17040000 0x8000>;
+			#clock-cells = <1>;
+
+			clocks = <&xtcxo>,
+				 <&cmu_top DOUT_CLKCMU_FSYS1_BUS>,
+				 <&cmu_top GOUT_CLKCMU_FSYS1_MMC_CARD>,
+				 <&cmu_top DOUT_CLKCMU_FSYS1_USBDRD>;
+			clock-names = "oscclk",
+				      "dout_clkcmu_fsys1_bus",
+				      "gout_clkcmu_fsys1_mmc_card",
+				      "dout_clkcmu_fsys1_usbdrd";
+		};
+
+		cmu_fsys0: clock-controller@17700000 {
+			compatible = "samsung,exynosautov9-cmu-fsys0";
+			reg = <0x17700000 0x8000>;
+			#clock-cells = <1>;
+
+			clocks = <&xtcxo>,
+				 <&cmu_top DOUT_CLKCMU_FSYS0_BUS>,
+				 <&cmu_top DOUT_CLKCMU_FSYS0_PCIE>;
+			clock-names = "oscclk",
+				      "dout_clkcmu_fsys0_bus",
+				      "dout_clkcmu_fsys0_pcie";
+		};
+
+		cmu_fsys2: clock-controller@17c00000 {
+			compatible = "samsung,exynosautov9-cmu-fsys2";
+			reg = <0x17c00000 0x8000>;
+			#clock-cells = <1>;
+
+			clocks = <&xtcxo>,
+				 <&cmu_top DOUT_CLKCMU_FSYS2_BUS>,
+				 <&cmu_top DOUT_CLKCMU_FSYS2_UFS_EMBD>,
+				 <&cmu_top DOUT_CLKCMU_FSYS2_ETHERNET>;
+			clock-names = "oscclk",
+				      "dout_clkcmu_fsys2_bus",
+				      "dout_fsys2_clkcmu_ufs_embd",
+				      "dout_fsys2_clkcmu_ethernet";
+		};
+
+		cmu_core: clock-controller@1b030000 {
+			compatible = "samsung,exynosautov9-cmu-core";
+			reg = <0x1b030000 0x8000>;
+			#clock-cells = <1>;
+
+			clocks = <&xtcxo>,
+				 <&cmu_top DOUT_CLKCMU_CORE_BUS>;
+			clock-names = "oscclk",
+				      "dout_clkcmu_core_bus";
+		};
+
+		cmu_busmc: clock-controller@1b200000 {
+			compatible = "samsung,exynosautov9-cmu-busmc";
+			reg = <0x1b200000 0x8000>;
+			#clock-cells = <1>;
+
+			clocks = <&xtcxo>,
+				 <&cmu_top DOUT_CLKCMU_BUSMC_BUS>;
+			clock-names = "oscclk",
+				      "dout_clkcmu_busmc_bus";
+		};
+
+		cmu_top: clock-controller@1b240000 {
+			compatible = "samsung,exynosautov9-cmu-top";
+			reg = <0x1b240000 0x8000>;
+			#clock-cells = <1>;
+
+			clocks = <&xtcxo>;
+			clock-names = "oscclk";
+		};
+
 		gic: interrupt-controller@10101000 {
 			compatible = "arm,gic-400";
 			#interrupt-cells = <3>;
@@ -202,12 +294,22 @@
 						 IRQ_TYPE_LEVEL_HIGH)>;
 		};
 
+		pdma0: dma-controller@1b2e0000 {
+			compatible = "arm,pl330", "arm,primecell";
+			reg = <0x1b2e0000 0x1000>;
+			interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cmu_busmc CLK_GOUT_BUSMC_PDMA0_PCLK>;
+			clock-names = "apb_pclk";
+			arm,pl330-broken-no-flushp;
+			#dma-cells = <1>;
+		};
+
 		pinctrl_alive: pinctrl@10450000 {
 			compatible = "samsung,exynosautov9-pinctrl";
 			reg = <0x10450000 0x1000>;
 
 			wakeup-interrupt-controller {
-				compatible = "samsung,exynos7-wakeup-eint";
+				compatible = "samsung,exynosautov9-wakeup-eint";
 			};
 		};
 
@@ -249,6 +351,22 @@
 		pmu_system_controller: system-controller@10460000 {
 			compatible = "samsung,exynos7-pmu", "syscon";
 			reg = <0x10460000 0x10000>;
+
+			reboot: syscon-reboot {
+				compatible = "syscon-reboot";
+				regmap = <&pmu_system_controller>;
+				offset = <0x3a00>; /* SYSTEM_CONFIGURATION */
+				value = <0x2>;
+				mask = <0x2>;
+			};
+
+			reboot-mode {
+				compatible = "syscon-reboot-mode";
+				offset = <0x810>; /* SYSIP_DAT0 */
+				mode-bootloader = <EXYNOSAUTOV9_BOOT_BOOTLOADER>;
+				mode-fastboot = <EXYNOSAUTOV9_BOOT_FASTBOOT>;
+				mode-recovery = <EXYNOSAUTOV9_BOOT_RECOVERY>;
+			};
 		};
 
 		syscon_fsys2: syscon@17c20000 {
@@ -256,19 +374,1107 @@
 			reg = <0x17c20000 0x1000>;
 		};
 
-		/* USI: UART */
-		serial_0: uart@10300000 {
-			compatible = "samsung,exynos850-uart";
-			reg = <0x10300000 0x100>;
-			interrupts = <GIC_SPI 345 IRQ_TYPE_LEVEL_HIGH>;
-			pinctrl-names = "default";
-			pinctrl-0 = <&uart0_bus_dual>;
-			clocks = <&uart_clock>, <&uart_clock>;
-			clock-names = "uart", "clk_uart_baud0";
+		syscon_peric0: syscon@10220000 {
+			compatible = "samsung,exynosautov9-sysreg", "syscon";
+			reg = <0x10220000 0x2000>;
+		};
+
+		syscon_peric1: syscon@10820000 {
+			compatible = "samsung,exynosautov9-sysreg", "syscon";
+			reg = <0x10820000 0x2000>;
+		};
+
+		usi_0: usi@103000c0 {
+			compatible = "samsung,exynosautov9-usi",
+				     "samsung,exynos850-usi";
+			reg = <0x103000c0 0x20>;
+			samsung,sysreg = <&syscon_peric0 0x1000>;
+			samsung,mode = <USI_V2_UART>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			clocks = <&cmu_peric0 CLK_GOUT_PERIC0_PCLK_0>,
+				 <&cmu_peric0 CLK_GOUT_PERIC0_IPCLK_0>;
+			clock-names = "pclk", "ipclk";
+			status = "disabled";
+
+			serial_0: serial@10300000 {
+				compatible = "samsung,exynosautov9-uart",
+					     "samsung,exynos850-uart";
+				reg = <0x10300000 0xc0>;
+				interrupts = <GIC_SPI 345 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&uart0_bus>;
+				clocks = <&cmu_peric0 CLK_GOUT_PERIC0_PCLK_0>,
+					 <&cmu_peric0 CLK_GOUT_PERIC0_IPCLK_0>;
+				clock-names = "uart", "clk_uart_baud0";
+				samsung,uart-fifosize = <256>;
+				status = "disabled";
+			};
+
+			spi_0: spi@10300000 {
+				compatible = "samsung,exynosautov9-spi";
+				reg = <0x10300000 0x30>;
+				interrupts = <GIC_SPI 345 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&spi0_bus &spi0_cs_func>;
+				clocks = <&cmu_peric0 CLK_GOUT_PERIC0_IPCLK_0>,
+					 <&cmu_peric0 CLK_DOUT_PERIC0_USI00_USI>,
+					 <&cmu_peric0 CLK_GOUT_PERIC0_PCLK_0>;
+				clock-names = "spi", "spi_busclk0", "spi_ioclk";
+				samsung,spi-src-clk = <0>;
+				dmas = <&pdma0 1>, <&pdma0 0>;
+				dma-names = "tx", "rx";
+				num-cs = <1>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			hsi2c_0: i2c@10300000 {
+				compatible = "samsung,exynosautov9-hsi2c";
+				reg = <0x10300000 0xc0>;
+				interrupts = <GIC_SPI 345 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&hsi2c0_bus>;
+				clocks = <&cmu_peric0 CLK_GOUT_PERIC0_IPCLK_0>,
+					 <&cmu_peric0 CLK_GOUT_PERIC0_PCLK_0>;
+				clock-names = "hsi2c", "hsi2c_pclk";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+		};
+
+		usi_i2c_0: usi@103100c0 {
+			compatible = "samsung,exynosautov9-usi",
+				     "samsung,exynos850-usi";
+			reg = <0x103100c0 0x20>;
+			samsung,sysreg = <&syscon_peric0 0x1004>;
+			samsung,mode = <USI_V2_I2C>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			clocks = <&cmu_peric0 CLK_GOUT_PERIC0_PCLK_1>,
+				 <&cmu_peric0 CLK_GOUT_PERIC0_IPCLK_1>;
+			clock-names = "pclk", "ipclk";
+			status = "disabled";
+
+			hsi2c_1: i2c@10310000 {
+				compatible = "samsung,exynosautov9-hsi2c";
+				reg = <0x10310000 0xc0>;
+				interrupts = <GIC_SPI 344 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&hsi2c1_bus>;
+				clocks = <&cmu_peric0 CLK_GOUT_PERIC0_IPCLK_1>,
+					 <&cmu_peric0 CLK_GOUT_PERIC0_PCLK_1>;
+				clock-names = "hsi2c", "hsi2c_pclk";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+		};
+
+		usi_1: usi@103200c0 {
+			compatible = "samsung,exynosautov9-usi",
+				     "samsung,exynos850-usi";
+			reg = <0x103200c0 0x20>;
+			samsung,sysreg = <&syscon_peric0 0x1008>;
+			samsung,mode = <USI_V2_UART>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			clocks = <&cmu_peric0 CLK_GOUT_PERIC0_PCLK_2>,
+				 <&cmu_peric0 CLK_GOUT_PERIC0_IPCLK_2>;
+			clock-names = "pclk", "ipclk";
+			status = "disabled";
+
+			serial_1: serial@10320000 {
+				compatible = "samsung,exynosautov9-uart",
+					     "samsung,exynos850-uart";
+				reg = <0x10320000 0xc0>;
+				interrupts = <GIC_SPI 347 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&uart1_bus>;
+				clocks = <&cmu_peric0 CLK_GOUT_PERIC0_PCLK_2>,
+					 <&cmu_peric0 CLK_GOUT_PERIC0_IPCLK_2>;
+				clock-names = "uart", "clk_uart_baud0";
+				samsung,uart-fifosize = <256>;
+				status = "disabled";
+			};
+
+			spi_1: spi@10320000 {
+				compatible = "samsung,exynosautov9-spi";
+				reg = <0x10320000 0x30>;
+				interrupts = <GIC_SPI 347 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&spi1_bus &spi1_cs_func>;
+				clocks = <&cmu_peric0 CLK_GOUT_PERIC0_IPCLK_2>,
+					 <&cmu_peric0 CLK_DOUT_PERIC0_USI01_USI>,
+					 <&cmu_peric0 CLK_GOUT_PERIC0_PCLK_2>;
+				clock-names = "spi", "spi_busclk0", "spi_ioclk";
+				samsung,spi-src-clk = <0>;
+				dmas = <&pdma0 3>, <&pdma0 2>;
+				dma-names = "tx", "rx";
+				num-cs = <1>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			hsi2c_2: i2c@10320000 {
+				compatible = "samsung,exynosautov9-hsi2c";
+				reg = <0x10320000 0xc0>;
+				interrupts = <GIC_SPI 347 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&hsi2c2_bus>;
+				clocks = <&cmu_peric0 CLK_GOUT_PERIC0_IPCLK_2>,
+					 <&cmu_peric0 CLK_GOUT_PERIC0_PCLK_2>;
+				clock-names = "hsi2c", "hsi2c_pclk";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+		};
+
+		usi_i2c_1: usi@103300c0 {
+			compatible = "samsung,exynosautov9-usi",
+				     "samsung,exynos850-usi";
+			reg = <0x103300c0 0x20>;
+			samsung,sysreg = <&syscon_peric0 0x100c>;
+			samsung,mode = <USI_V2_I2C>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			clocks = <&cmu_peric0 CLK_GOUT_PERIC0_PCLK_3>,
+				 <&cmu_peric0 CLK_GOUT_PERIC0_IPCLK_3>;
+			clock-names = "pclk", "ipclk";
+			status = "disabled";
+
+			hsi2c_3: i2c@10330000 {
+				compatible = "samsung,exynosautov9-hsi2c";
+				reg = <0x10330000 0xc0>;
+				interrupts = <GIC_SPI 346 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&hsi2c3_bus>;
+				clocks = <&cmu_peric0 CLK_GOUT_PERIC0_IPCLK_3>,
+					 <&cmu_peric0 CLK_GOUT_PERIC0_PCLK_3>;
+				clock-names = "hsi2c", "hsi2c_pclk";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+		};
+
+		usi_2: usi@103400c0 {
+			compatible = "samsung,exynosautov9-usi",
+				     "samsung,exynos850-usi";
+			reg = <0x103400c0 0x20>;
+			samsung,sysreg = <&syscon_peric0 0x1010>;
+			samsung,mode = <USI_V2_UART>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			clocks = <&cmu_peric0 CLK_GOUT_PERIC0_PCLK_4>,
+				 <&cmu_peric0 CLK_GOUT_PERIC0_IPCLK_4>;
+			clock-names = "pclk", "ipclk";
 			status = "disabled";
+
+			serial_2: serial@10340000 {
+				compatible = "samsung,exynosautov9-uart",
+					     "samsung,exynos850-uart";
+				reg = <0x10340000 0xc0>;
+				interrupts = <GIC_SPI 349 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&uart2_bus>;
+				clocks = <&cmu_peric0 CLK_GOUT_PERIC0_PCLK_4>,
+					 <&cmu_peric0 CLK_GOUT_PERIC0_IPCLK_4>;
+				clock-names = "uart", "clk_uart_baud0";
+				samsung,uart-fifosize = <64>;
+				status = "disabled";
+			};
+
+			spi_2: spi@10340000 {
+				compatible = "samsung,exynosautov9-spi";
+				reg = <0x10340000 0x30>;
+				interrupts = <GIC_SPI 349 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&spi2_bus &spi2_cs_func>;
+				clocks = <&cmu_peric0 CLK_GOUT_PERIC0_IPCLK_4>,
+					 <&cmu_peric0 CLK_DOUT_PERIC0_USI02_USI>,
+					 <&cmu_peric0 CLK_GOUT_PERIC0_PCLK_4>;
+				clock-names = "spi", "spi_busclk0", "spi_ioclk";
+				samsung,spi-src-clk = <0>;
+				dmas = <&pdma0 5>, <&pdma0 4>;
+				dma-names = "tx", "rx";
+				num-cs = <1>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			hsi2c_4: i2c@10340000 {
+				compatible = "samsung,exynosautov9-hsi2c";
+				reg = <0x10340000 0xc0>;
+				interrupts = <GIC_SPI 349 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&hsi2c4_bus>;
+				clocks = <&cmu_peric0 CLK_GOUT_PERIC0_IPCLK_4>,
+					 <&cmu_peric0 CLK_GOUT_PERIC0_PCLK_4>;
+				clock-names = "hsi2c", "hsi2c_pclk";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
 		};
 
-		ufs_0_phy: ufs0-phy@17e04000 {
+		usi_i2c_2: usi@103500c0 {
+			compatible = "samsung,exynosautov9-usi",
+				     "samsung,exynos850-usi";
+			reg = <0x103500c0 0x20>;
+			samsung,sysreg = <&syscon_peric0 0x1014>;
+			samsung,mode = <USI_V2_I2C>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			clocks = <&cmu_peric0 CLK_GOUT_PERIC0_PCLK_5>,
+				 <&cmu_peric0 CLK_GOUT_PERIC0_IPCLK_5>;
+			clock-names = "pclk", "ipclk";
+			status = "disabled";
+
+			hsi2c_5: i2c@10350000 {
+				compatible = "samsung,exynosautov9-hsi2c";
+				reg = <0x10350000 0xc0>;
+				interrupts = <GIC_SPI 348 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&hsi2c5_bus>;
+				clocks = <&cmu_peric0 CLK_GOUT_PERIC0_IPCLK_5>,
+					 <&cmu_peric0 CLK_GOUT_PERIC0_PCLK_5>;
+				clock-names = "hsi2c", "hsi2c_pclk";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+		};
+
+		usi_3: usi@103600c0 {
+			compatible = "samsung,exynosautov9-usi",
+				     "samsung,exynos850-usi";
+			reg = <0x103600c0 0x20>;
+			samsung,sysreg = <&syscon_peric0 0x1018>;
+			samsung,mode = <USI_V2_UART>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			clocks = <&cmu_peric0 CLK_GOUT_PERIC0_PCLK_6>,
+				 <&cmu_peric0 CLK_GOUT_PERIC0_IPCLK_6>;
+			clock-names = "pclk", "ipclk";
+			status = "disabled";
+
+			serial_3: serial@10360000 {
+				compatible = "samsung,exynosautov9-uart",
+					     "samsung,exynos850-uart";
+				reg = <0x10360000 0xc0>;
+				interrupts = <GIC_SPI 351 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&uart3_bus>;
+				clocks = <&cmu_peric0 CLK_GOUT_PERIC0_PCLK_6>,
+					 <&cmu_peric0 CLK_GOUT_PERIC0_IPCLK_6>;
+				clock-names = "uart", "clk_uart_baud0";
+				samsung,uart-fifosize = <64>;
+				status = "disabled";
+			};
+
+			spi_3: spi@10360000 {
+				compatible = "samsung,exynosautov9-spi";
+				reg = <0x10360000 0x30>;
+				interrupts = <GIC_SPI 351 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&spi3_bus &spi3_cs_func>;
+				clocks = <&cmu_peric0 CLK_GOUT_PERIC0_IPCLK_6>,
+					 <&cmu_peric0 CLK_DOUT_PERIC0_USI03_USI>,
+					 <&cmu_peric0 CLK_GOUT_PERIC0_PCLK_6>;
+				clock-names = "spi", "spi_busclk0", "spi_ioclk";
+				samsung,spi-src-clk = <0>;
+				dmas = <&pdma0 7>, <&pdma0 6>;
+				dma-names = "tx", "rx";
+				num-cs = <1>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			hsi2c_6: i2c@10360000 {
+				compatible = "samsung,exynosautov9-hsi2c";
+				reg = <0x10360000 0xc0>;
+				interrupts = <GIC_SPI 351 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&hsi2c6_bus>;
+				clocks = <&cmu_peric0 CLK_GOUT_PERIC0_IPCLK_6>,
+					 <&cmu_peric0 CLK_GOUT_PERIC0_PCLK_6>;
+				clock-names = "hsi2c", "hsi2c_pclk";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+		};
+
+		usi_i2c_3: usi@103700c0 {
+			compatible = "samsung,exynosautov9-usi",
+				     "samsung,exynos850-usi";
+			reg = <0x103700c0 0x20>;
+			samsung,sysreg = <&syscon_peric0 0x101c>;
+			samsung,mode = <USI_V2_I2C>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			clocks = <&cmu_peric0 CLK_GOUT_PERIC0_PCLK_7>,
+				 <&cmu_peric0 CLK_GOUT_PERIC0_IPCLK_7>;
+			clock-names = "pclk", "ipclk";
+			status = "disabled";
+
+			hsi2c_7: i2c@10370000 {
+				compatible = "samsung,exynosautov9-hsi2c";
+				reg = <0x10370000 0xc0>;
+				interrupts = <GIC_SPI 350 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&hsi2c7_bus>;
+				clocks = <&cmu_peric0 CLK_GOUT_PERIC0_IPCLK_7>,
+					 <&cmu_peric0 CLK_GOUT_PERIC0_PCLK_7>;
+				clock-names = "hsi2c", "hsi2c_pclk";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+		};
+
+		usi_4: usi@103800c0 {
+			compatible = "samsung,exynosautov9-usi",
+				     "samsung,exynos850-usi";
+			reg = <0x103800c0 0x20>;
+			samsung,sysreg = <&syscon_peric0 0x1020>;
+			samsung,mode = <USI_V2_UART>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			clocks = <&cmu_peric0 CLK_GOUT_PERIC0_PCLK_8>,
+				 <&cmu_peric0 CLK_GOUT_PERIC0_IPCLK_8>;
+			clock-names = "pclk", "ipclk";
+			status = "disabled";
+
+			serial_4: serial@10380000 {
+				compatible = "samsung,exynosautov9-uart",
+					     "samsung,exynos850-uart";
+				reg = <0x10380000 0xc0>;
+				interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&uart4_bus>;
+				clocks = <&cmu_peric0 CLK_GOUT_PERIC0_PCLK_8>,
+					 <&cmu_peric0 CLK_GOUT_PERIC0_IPCLK_8>;
+				clock-names = "uart", "clk_uart_baud0";
+				samsung,uart-fifosize = <64>;
+				status = "disabled";
+			};
+
+			spi_4: spi@10380000 {
+				compatible = "samsung,exynosautov9-spi";
+				reg = <0x10380000 0x30>;
+				interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&spi4_bus &spi4_cs_func>;
+				clocks = <&cmu_peric0 CLK_GOUT_PERIC0_IPCLK_8>,
+					 <&cmu_peric0 CLK_DOUT_PERIC0_USI04_USI>,
+					 <&cmu_peric0 CLK_GOUT_PERIC0_PCLK_8>;
+				clock-names = "spi", "spi_busclk0", "spi_ioclk";
+				samsung,spi-src-clk = <0>;
+				dmas = <&pdma0 9>, <&pdma0 8>;
+				dma-names = "tx", "rx";
+				num-cs = <1>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			hsi2c_8: i2c@10380000 {
+				compatible = "samsung,exynosautov9-hsi2c";
+				reg = <0x10380000 0xc0>;
+				interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&hsi2c8_bus>;
+				clocks = <&cmu_peric0 CLK_GOUT_PERIC0_IPCLK_8>,
+					 <&cmu_peric0 CLK_GOUT_PERIC0_PCLK_8>;
+				clock-names = "hsi2c", "hsi2c_pclk";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+		};
+
+		usi_i2c_4: usi@103900c0 {
+			compatible = "samsung,exynosautov9-usi",
+				     "samsung,exynos850-usi";
+			reg = <0x103900c0 0x20>;
+			samsung,sysreg = <&syscon_peric0 0x1024>;
+			samsung,mode = <USI_V2_I2C>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			clocks = <&cmu_peric0 CLK_GOUT_PERIC0_PCLK_9>,
+				 <&cmu_peric0 CLK_GOUT_PERIC0_IPCLK_9>;
+			clock-names = "pclk", "ipclk";
+			status = "disabled";
+
+			hsi2c_9: i2c@10390000 {
+				compatible = "samsung,exynosautov9-hsi2c";
+				reg = <0x10390000 0xc0>;
+				interrupts = <GIC_SPI 352 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&hsi2c9_bus>;
+				clocks = <&cmu_peric0 CLK_GOUT_PERIC0_IPCLK_9>,
+					 <&cmu_peric0 CLK_GOUT_PERIC0_PCLK_9>;
+				clock-names = "hsi2c", "hsi2c_pclk";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+		};
+
+		usi_5: usi@103a00c0 {
+			compatible = "samsung,exynosautov9-usi",
+				     "samsung,exynos850-usi";
+			reg = <0x103a00c0 0x20>;
+			samsung,sysreg = <&syscon_peric0 0x1028>;
+			samsung,mode = <USI_V2_UART>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			clocks = <&cmu_peric0 CLK_GOUT_PERIC0_PCLK_10>,
+				 <&cmu_peric0 CLK_GOUT_PERIC0_IPCLK_10>;
+			clock-names = "pclk", "ipclk";
+			status = "disabled";
+
+			serial_5: serial@103a0000 {
+				compatible = "samsung,exynosautov9-uart",
+					     "samsung,exynos850-uart";
+				reg = <0x103a0000 0xc0>;
+				interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&uart5_bus>;
+				clocks = <&cmu_peric0 CLK_GOUT_PERIC0_PCLK_10>,
+					 <&cmu_peric0 CLK_GOUT_PERIC0_IPCLK_10>;
+				clock-names = "uart", "clk_uart_baud0";
+				samsung,uart-fifosize = <64>;
+				status = "disabled";
+			};
+
+			spi_5: spi@103a0000 {
+				compatible = "samsung,exynosautov9-spi";
+				reg = <0x103a0000 0x30>;
+				interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&spi5_bus &spi5_cs_func>;
+				clocks = <&cmu_peric0 CLK_GOUT_PERIC0_IPCLK_10>,
+					 <&cmu_peric0 CLK_DOUT_PERIC0_USI05_USI>,
+					 <&cmu_peric0 CLK_GOUT_PERIC0_PCLK_10>;
+				clock-names = "spi", "spi_busclk0", "spi_ioclk";
+				samsung,spi-src-clk = <0>;
+				dmas = <&pdma0 11>, <&pdma0 10>;
+				dma-names = "tx", "rx";
+				num-cs = <1>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			hsi2c_10: i2c@103a0000 {
+				compatible = "samsung,exynosautov9-hsi2c";
+				reg = <0x103a0000 0xc0>;
+				interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&hsi2c10_bus>;
+				clocks = <&cmu_peric0 CLK_GOUT_PERIC0_IPCLK_10>,
+					 <&cmu_peric0 CLK_GOUT_PERIC0_PCLK_10>;
+				clock-names = "hsi2c", "hsi2c_pclk";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+		};
+
+		usi_i2c_5: usi@103b00c0 {
+			compatible = "samsung,exynosautov9-usi",
+				     "samsung,exynos850-usi";
+			reg = <0x103b00c0 0x20>;
+			samsung,sysreg = <&syscon_peric0 0x102c>;
+			samsung,mode = <USI_V2_I2C>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			clocks = <&cmu_peric0 CLK_GOUT_PERIC0_PCLK_11>,
+				 <&cmu_peric0 CLK_GOUT_PERIC0_IPCLK_11>;
+			clock-names = "pclk", "ipclk";
+			status = "disabled";
+
+			hsi2c_11: i2c@103b0000 {
+				compatible = "samsung,exynosautov9-hsi2c";
+				reg = <0x103b0000 0xc0>;
+				interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&hsi2c11_bus>;
+				clocks = <&cmu_peric0 CLK_GOUT_PERIC0_IPCLK_11>,
+					 <&cmu_peric0 CLK_GOUT_PERIC0_PCLK_11>;
+				clock-names = "hsi2c", "hsi2c_pclk";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+		};
+
+		usi_6: usi@109000c0 {
+			compatible = "samsung,exynosautov9-usi",
+				     "samsung,exynos850-usi";
+			reg = <0x109000c0 0x20>;
+			samsung,sysreg = <&syscon_peric1 0x1000>;
+			samsung,mode = <USI_V2_UART>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			clocks = <&cmu_peric1 CLK_GOUT_PERIC1_PCLK_0>,
+				 <&cmu_peric1 CLK_GOUT_PERIC1_IPCLK_0>;
+			clock-names = "pclk", "ipclk";
+			status = "disabled";
+
+			serial_6: serial@10900000 {
+				compatible = "samsung,exynosautov9-uart",
+					     "samsung,exynos850-uart";
+				reg = <0x10900000 0xc0>;
+				interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&uart6_bus>;
+				clocks = <&cmu_peric1 CLK_GOUT_PERIC1_PCLK_0>,
+					 <&cmu_peric1 CLK_GOUT_PERIC1_IPCLK_0>;
+				clock-names = "uart", "clk_uart_baud0";
+				samsung,uart-fifosize = <256>;
+				status = "disabled";
+			};
+
+			spi_6: spi@10900000 {
+				compatible = "samsung,exynosautov9-spi";
+				reg = <0x10900000 0x30>;
+				interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&spi6_bus &spi6_cs_func>;
+				clocks = <&cmu_peric1 CLK_GOUT_PERIC1_IPCLK_0>,
+					 <&cmu_peric1 CLK_DOUT_PERIC1_USI06_USI>,
+					 <&cmu_peric1 CLK_GOUT_PERIC1_PCLK_0>;
+				clock-names = "spi", "spi_busclk0", "spi_ioclk";
+				samsung,spi-src-clk = <0>;
+				dmas = <&pdma0 13>, <&pdma0 12>;
+				dma-names = "tx", "rx";
+				num-cs = <1>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			hsi2c_12: i2c@10900000 {
+				compatible = "samsung,exynosautov9-hsi2c";
+				reg = <0x10900000 0xc0>;
+				interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&hsi2c12_bus>;
+				clocks = <&cmu_peric1 CLK_GOUT_PERIC1_IPCLK_0>,
+					 <&cmu_peric1 CLK_GOUT_PERIC1_PCLK_0>;
+				clock-names = "hsi2c", "hsi2c_pclk";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+		};
+
+		usi_i2c_6: usi@109100c0 {
+			compatible = "samsung,exynosautov9-usi",
+				     "samsung,exynos850-usi";
+			reg = <0x109100c0 0x20>;
+			samsung,sysreg = <&syscon_peric1 0x1004>;
+			samsung,mode = <USI_V2_I2C>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			clocks = <&cmu_peric1 CLK_GOUT_PERIC1_PCLK_1>,
+				 <&cmu_peric1 CLK_GOUT_PERIC1_IPCLK_1>;
+			clock-names = "pclk", "ipclk";
+			status = "disabled";
+
+			hsi2c_13: i2c@10910000 {
+				compatible = "samsung,exynosautov9-hsi2c";
+				reg = <0x10910000 0xc0>;
+				interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&hsi2c13_bus>;
+				clocks = <&cmu_peric1 CLK_GOUT_PERIC1_IPCLK_1>,
+					 <&cmu_peric1 CLK_GOUT_PERIC1_PCLK_1>;
+				clock-names = "hsi2c", "hsi2c_pclk";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+		};
+
+		usi_7: usi@109200c0 {
+			compatible = "samsung,exynosautov9-usi",
+				     "samsung,exynos850-usi";
+			reg = <0x109200c0 0x20>;
+			samsung,sysreg = <&syscon_peric1 0x1008>;
+			samsung,mode = <USI_V2_UART>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			clocks = <&cmu_peric1 CLK_GOUT_PERIC1_PCLK_2>,
+				 <&cmu_peric1 CLK_GOUT_PERIC1_IPCLK_2>;
+			clock-names = "pclk", "ipclk";
+			status = "disabled";
+
+			serial_7: serial@10920000 {
+				compatible = "samsung,exynosautov9-uart",
+					     "samsung,exynos850-uart";
+				reg = <0x10920000 0xc0>;
+				interrupts = <GIC_SPI 360 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&uart7_bus>;
+				clocks = <&cmu_peric1 CLK_GOUT_PERIC1_PCLK_2>,
+					 <&cmu_peric1 CLK_GOUT_PERIC1_IPCLK_2>;
+				clock-names = "uart", "clk_uart_baud0";
+				samsung,uart-fifosize = <64>;
+				status = "disabled";
+			};
+
+			spi_7: spi@10920000 {
+				compatible = "samsung,exynosautov9-spi";
+				reg = <0x10920000 0x30>;
+				interrupts = <GIC_SPI 360 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&spi7_bus &spi7_cs_func>;
+				clocks = <&cmu_peric1 CLK_GOUT_PERIC1_IPCLK_2>,
+					 <&cmu_peric1 CLK_DOUT_PERIC1_USI07_USI>,
+					 <&cmu_peric1 CLK_GOUT_PERIC1_PCLK_2>;
+				clock-names = "spi", "spi_busclk0", "spi_ioclk";
+				samsung,spi-src-clk = <0>;
+				dmas = <&pdma0 15>, <&pdma0 14>;
+				dma-names = "tx", "rx";
+				num-cs = <1>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			hsi2c_14: i2c@10920000 {
+				compatible = "samsung,exynosautov9-hsi2c";
+				reg = <0x10920000 0xc0>;
+				interrupts = <GIC_SPI 360 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&hsi2c14_bus>;
+				clocks = <&cmu_peric1 CLK_GOUT_PERIC1_IPCLK_2>,
+					 <&cmu_peric1 CLK_GOUT_PERIC1_PCLK_2>;
+				clock-names = "hsi2c", "hsi2c_pclk";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+		};
+
+		usi_i2c_7: usi@109300c0 {
+			compatible = "samsung,exynosautov9-usi",
+				     "samsung,exynos850-usi";
+			reg = <0x109300c0 0x20>;
+			samsung,sysreg = <&syscon_peric1 0x100c>;
+			samsung,mode = <USI_V2_I2C>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			clocks = <&cmu_peric1 CLK_GOUT_PERIC1_PCLK_3>,
+				 <&cmu_peric1 CLK_GOUT_PERIC1_IPCLK_3>;
+			clock-names = "pclk", "ipclk";
+			status = "disabled";
+
+			hsi2c_15: i2c@10930000 {
+				compatible = "samsung,exynosautov9-hsi2c";
+				reg = <0x10930000 0xc0>;
+				interrupts = <GIC_SPI 359 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&hsi2c15_bus>;
+				clocks = <&cmu_peric1 CLK_GOUT_PERIC1_IPCLK_3>,
+					 <&cmu_peric1 CLK_GOUT_PERIC1_PCLK_3>;
+				clock-names = "hsi2c", "hsi2c_pclk";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+		};
+
+		usi_8: usi@109400c0 {
+			compatible = "samsung,exynosautov9-usi",
+				     "samsung,exynos850-usi";
+			reg = <0x109400c0 0x20>;
+			samsung,sysreg = <&syscon_peric1 0x1010>;
+			samsung,mode = <USI_V2_UART>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			clocks = <&cmu_peric1 CLK_GOUT_PERIC1_PCLK_4>,
+				 <&cmu_peric1 CLK_GOUT_PERIC1_IPCLK_4>;
+			clock-names = "pclk", "ipclk";
+			status = "disabled";
+
+			serial_8: serial@10940000 {
+				compatible = "samsung,exynosautov9-uart",
+					     "samsung,exynos850-uart";
+				reg = <0x10940000 0xc0>;
+				interrupts = <GIC_SPI 362 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&uart8_bus>;
+				clocks = <&cmu_peric1 CLK_GOUT_PERIC1_PCLK_4>,
+					 <&cmu_peric1 CLK_GOUT_PERIC1_IPCLK_4>;
+				clock-names = "uart", "clk_uart_baud0";
+				samsung,uart-fifosize = <64>;
+				status = "disabled";
+			};
+
+			spi_8: spi@10940000 {
+				compatible = "samsung,exynosautov9-spi";
+				reg = <0x10940000 0x30>;
+				interrupts = <GIC_SPI 362 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&spi8_bus &spi8_cs_func>;
+				clocks = <&cmu_peric1 CLK_GOUT_PERIC1_IPCLK_4>,
+					 <&cmu_peric1 CLK_DOUT_PERIC1_USI08_USI>,
+					 <&cmu_peric1 CLK_GOUT_PERIC1_PCLK_4>;
+				clock-names = "spi", "spi_busclk0", "spi_ioclk";
+				samsung,spi-src-clk = <0>;
+				dmas = <&pdma0 17>, <&pdma0 16>;
+				dma-names = "tx", "rx";
+				num-cs = <1>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			hsi2c_16: i2c@10940000 {
+				compatible = "samsung,exynosautov9-hsi2c";
+				reg = <0x10940000 0xc0>;
+				interrupts = <GIC_SPI 362 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&hsi2c16_bus>;
+				clocks = <&cmu_peric1 CLK_GOUT_PERIC1_IPCLK_4>,
+					 <&cmu_peric1 CLK_GOUT_PERIC1_PCLK_4>;
+				clock-names = "hsi2c", "hsi2c_pclk";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+		};
+
+		usi_i2c_8: usi@109500c0 {
+			compatible = "samsung,exynosautov9-usi",
+				     "samsung,exynos850-usi";
+			reg = <0x109500c0 0x20>;
+			samsung,sysreg = <&syscon_peric1 0x1014>;
+			samsung,mode = <USI_V2_I2C>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			clocks = <&cmu_peric1 CLK_GOUT_PERIC1_PCLK_5>,
+				 <&cmu_peric1 CLK_GOUT_PERIC1_IPCLK_5>;
+			clock-names = "pclk", "ipclk";
+			status = "disabled";
+
+			hsi2c_17: i2c@10950000 {
+				compatible = "samsung,exynosautov9-hsi2c";
+				reg = <0x10950000 0xc0>;
+				interrupts = <GIC_SPI 361 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&hsi2c17_bus>;
+				clocks = <&cmu_peric1 CLK_GOUT_PERIC1_IPCLK_5>,
+					 <&cmu_peric1 CLK_GOUT_PERIC1_PCLK_5>;
+				clock-names = "hsi2c", "hsi2c_pclk";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+		};
+
+		usi_9: usi@109600c0 {
+			compatible = "samsung,exynosautov9-usi",
+				     "samsung,exynos850-usi";
+			reg = <0x109600c0 0x20>;
+			samsung,sysreg = <&syscon_peric1 0x1018>;
+			samsung,mode = <USI_V2_UART>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			clocks = <&cmu_peric1 CLK_GOUT_PERIC1_PCLK_6>,
+				 <&cmu_peric1 CLK_GOUT_PERIC1_IPCLK_6>;
+			clock-names = "pclk", "ipclk";
+			status = "disabled";
+
+			serial_9: serial@10960000 {
+				compatible = "samsung,exynosautov9-uart",
+					     "samsung,exynos850-uart";
+				reg = <0x10960000 0xc0>;
+				interrupts = <GIC_SPI 364 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&uart9_bus>;
+				clocks = <&cmu_peric1 CLK_GOUT_PERIC1_PCLK_6>,
+					 <&cmu_peric1 CLK_GOUT_PERIC1_IPCLK_6>;
+				clock-names = "uart", "clk_uart_baud0";
+				samsung,uart-fifosize = <64>;
+				status = "disabled";
+			};
+
+			spi_9: spi@10960000 {
+				compatible = "samsung,exynosautov9-spi";
+				reg = <0x10960000 0x30>;
+				interrupts = <GIC_SPI 364 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&spi9_bus &spi9_cs_func>;
+				clocks = <&cmu_peric1 CLK_GOUT_PERIC1_IPCLK_6>,
+					 <&cmu_peric1 CLK_DOUT_PERIC1_USI09_USI>,
+					 <&cmu_peric1 CLK_GOUT_PERIC1_PCLK_6>;
+				clock-names = "spi", "spi_busclk0", "spi_ioclk";
+				samsung,spi-src-clk = <0>;
+				dmas = <&pdma0 19>, <&pdma0 18>;
+				dma-names = "tx", "rx";
+				num-cs = <1>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			hsi2c_18: i2c@10960000 {
+				compatible = "samsung,exynosautov9-hsi2c";
+				reg = <0x10960000 0xc0>;
+				interrupts = <GIC_SPI 364 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&hsi2c18_bus>;
+				clocks = <&cmu_peric1 CLK_GOUT_PERIC1_IPCLK_6>,
+					 <&cmu_peric1 CLK_GOUT_PERIC1_PCLK_6>;
+				clock-names = "hsi2c", "hsi2c_pclk";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+		};
+
+		usi_i2c_9: usi@109700c0 {
+			compatible = "samsung,exynosautov9-usi",
+				     "samsung,exynos850-usi";
+			reg = <0x109700c0 0x20>;
+			samsung,sysreg = <&syscon_peric1 0x101c>;
+			samsung,mode = <USI_V2_I2C>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			clocks = <&cmu_peric1 CLK_GOUT_PERIC1_PCLK_7>,
+				 <&cmu_peric1 CLK_GOUT_PERIC1_IPCLK_7>;
+			clock-names = "pclk", "ipclk";
+			status = "disabled";
+
+			hsi2c_19: i2c@10970000 {
+				compatible = "samsung,exynosautov9-hsi2c";
+				reg = <0x10970000 0xc0>;
+				interrupts = <GIC_SPI 363 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&hsi2c19_bus>;
+				clocks = <&cmu_peric1 CLK_GOUT_PERIC1_IPCLK_7>,
+					 <&cmu_peric1 CLK_GOUT_PERIC1_PCLK_7>;
+				clock-names = "hsi2c", "hsi2c_pclk";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+		};
+
+		usi_10: usi@109800c0 {
+			compatible = "samsung,exynosautov9-usi",
+				     "samsung,exynos850-usi";
+			reg = <0x109800c0 0x20>;
+			samsung,sysreg = <&syscon_peric1 0x1020>;
+			samsung,mode = <USI_V2_UART>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			clocks = <&cmu_peric1 CLK_GOUT_PERIC1_PCLK_8>,
+				 <&cmu_peric1 CLK_GOUT_PERIC1_IPCLK_8>;
+			clock-names = "pclk", "ipclk";
+			status = "disabled";
+
+			serial_10: serial@10980000 {
+				compatible = "samsung,exynosautov9-uart",
+					     "samsung,exynos850-uart";
+				reg = <0x10980000 0xc0>;
+				interrupts = <GIC_SPI 366 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&uart10_bus>;
+				clocks = <&cmu_peric1 CLK_GOUT_PERIC1_PCLK_8>,
+					 <&cmu_peric1 CLK_GOUT_PERIC1_IPCLK_8>;
+				clock-names = "uart", "clk_uart_baud0";
+				samsung,uart-fifosize = <64>;
+				status = "disabled";
+			};
+
+			spi_10: spi@10980000 {
+				compatible = "samsung,exynosautov9-spi";
+				reg = <0x10980000 0x30>;
+				interrupts = <GIC_SPI 366 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&spi10_bus &spi10_cs_func>;
+				clocks = <&cmu_peric1 CLK_GOUT_PERIC1_IPCLK_8>,
+					 <&cmu_peric1 CLK_DOUT_PERIC1_USI10_USI>,
+					 <&cmu_peric1 CLK_GOUT_PERIC1_PCLK_8>;
+				clock-names = "spi", "spi_busclk0", "spi_ioclk";
+				samsung,spi-src-clk = <0>;
+				dmas = <&pdma0 21>, <&pdma0 20>;
+				dma-names = "tx", "rx";
+				num-cs = <1>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			hsi2c_20: i2c@10980000 {
+				compatible = "samsung,exynosautov9-hsi2c";
+				reg = <0x10980000 0xc0>;
+				interrupts = <GIC_SPI 366 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&hsi2c20_bus>;
+				clocks = <&cmu_peric1 CLK_GOUT_PERIC1_IPCLK_8>,
+					 <&cmu_peric1 CLK_GOUT_PERIC1_PCLK_8>;
+				clock-names = "hsi2c", "hsi2c_pclk";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+		};
+
+		usi_i2c_10: usi@109900c0 {
+			compatible = "samsung,exynosautov9-usi",
+				     "samsung,exynos850-usi";
+			reg = <0x109900c0 0x20>;
+			samsung,sysreg = <&syscon_peric1 0x1024>;
+			samsung,mode = <USI_V2_I2C>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			clocks = <&cmu_peric1 CLK_GOUT_PERIC1_PCLK_9>,
+				 <&cmu_peric1 CLK_GOUT_PERIC1_IPCLK_9>;
+			clock-names = "pclk", "ipclk";
+			status = "disabled";
+
+			hsi2c_21: i2c@10990000 {
+				compatible = "samsung,exynosautov9-hsi2c";
+				reg = <0x10990000 0xc0>;
+				interrupts = <GIC_SPI 365 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&hsi2c21_bus>;
+				clocks = <&cmu_peric1 CLK_GOUT_PERIC1_IPCLK_9>,
+					 <&cmu_peric1 CLK_GOUT_PERIC1_PCLK_9>;
+				clock-names = "hsi2c", "hsi2c_pclk";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+		};
+
+		usi_11: usi@109a00c0 {
+			compatible = "samsung,exynosautov9-usi",
+				     "samsung,exynos850-usi";
+			reg = <0x109a00c0 0x20>;
+			samsung,sysreg = <&syscon_peric1 0x1028>;
+			samsung,mode = <USI_V2_UART>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			clocks = <&cmu_peric1 CLK_GOUT_PERIC1_PCLK_10>,
+				 <&cmu_peric1 CLK_GOUT_PERIC1_IPCLK_10>;
+			clock-names = "pclk", "ipclk";
+			status = "disabled";
+
+			serial_11: serial@109a0000 {
+				compatible = "samsung,exynosautov9-uart",
+					     "samsung,exynos850-uart";
+				reg = <0x109a0000 0xc0>;
+				interrupts = <GIC_SPI 368 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&uart11_bus>;
+				clocks = <&cmu_peric1 CLK_GOUT_PERIC1_PCLK_10>,
+					 <&cmu_peric1 CLK_GOUT_PERIC1_IPCLK_10>;
+				clock-names = "uart", "clk_uart_baud0";
+				samsung,uart-fifosize = <64>;
+				status = "disabled";
+			};
+
+			spi_11: spi@109a0000 {
+				compatible = "samsung,exynosautov9-spi";
+				reg = <0x109a0000 0x30>;
+				interrupts = <GIC_SPI 368 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&spi11_bus &spi11_cs_func>;
+				clocks = <&cmu_peric1 CLK_GOUT_PERIC1_IPCLK_10>,
+					 <&cmu_peric1 CLK_DOUT_PERIC1_USI11_USI>,
+					 <&cmu_peric1 CLK_GOUT_PERIC1_PCLK_10>;
+				clock-names = "spi", "spi_busclk0", "spi_ioclk";
+				samsung,spi-src-clk = <0>;
+				num-cs = <1>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			hsi2c_22: i2c@109a0000 {
+				compatible = "samsung,exynosautov9-hsi2c";
+				reg = <0x109a0000 0xc0>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&hsi2c22_bus>;
+				interrupts = <GIC_SPI 368 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&cmu_peric1 CLK_GOUT_PERIC1_IPCLK_10>,
+					 <&cmu_peric1 CLK_GOUT_PERIC1_PCLK_10>;
+				clock-names = "hsi2c", "hsi2c_pclk";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+		};
+
+		usi_i2c_11: usi@109b00c0 {
+			compatible = "samsung,exynosautov9-usi",
+				     "samsung,exynos850-usi";
+			reg = <0x109b00c0 0x20>;
+			samsung,sysreg = <&syscon_peric1 0x102c>;
+			samsung,mode = <USI_V2_I2C>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+			clocks = <&cmu_peric1 CLK_GOUT_PERIC1_PCLK_11>,
+				 <&cmu_peric1 CLK_GOUT_PERIC1_IPCLK_11>;
+			clock-names = "pclk", "ipclk";
+			status = "disabled";
+
+			hsi2c_23: i2c@109b0000 {
+				compatible = "samsung,exynosautov9-hsi2c";
+				reg = <0x109b0000 0xc0>;
+				interrupts = <GIC_SPI 367 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&hsi2c23_bus>;
+				clocks = <&cmu_peric1 CLK_GOUT_PERIC1_IPCLK_11>,
+					 <&cmu_peric1 CLK_GOUT_PERIC1_PCLK_11>;
+				clock-names = "hsi2c", "hsi2c_pclk";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+		};
+
+		ufs_0_phy: phy@17e04000 {
 			compatible = "samsung,exynosautov9-ufs-phy";
 			reg = <0x17e04000 0xc00>;
 			reg-names = "phy-pma";
@@ -279,17 +1485,17 @@
 			status = "disabled";
 		};
 
-		ufs_0: ufs0@17e00000 {
-			compatible ="samsung,exynosautov9-ufs";
+		ufs_0: ufs@17e00000 {
+			compatible = "samsung,exynosautov9-ufs";
 
-			reg = <0x17e00000 0x100>,  /* 0: HCI standard */
-				<0x17e01100 0x410>,  /* 1: Vendor-specific */
-				<0x17e80000 0x8000>,  /* 2: UNIPRO */
-				<0x17dc0000 0x2200>;  /* 3: UFS protector */
+			reg = <0x17e00000 0x100>,
+			      <0x17e01100 0x410>,
+			      <0x17e80000 0x8000>,
+			      <0x17dc0000 0x2200>;
 			reg-names = "hci", "vs_hci", "unipro", "ufsp";
 			interrupts = <GIC_SPI 227 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&ufs_core_clock>,
-				<&ufs_core_clock>;
+			clocks = <&cmu_fsys2 CLK_GOUT_FSYS2_UFS_EMBD0_ACLK>,
+				 <&cmu_fsys2 CLK_GOUT_FSYS2_UFS_EMBD0_UNIPRO>;
 			clock-names = "core_clk", "sclk_unipro_main";
 			freq-table-hz = <0 0>, <0 0>;
 			pinctrl-names = "default";
@@ -299,6 +1505,58 @@
 			samsung,sysreg = <&syscon_fsys2 0x710>;
 			status = "disabled";
 		};
+
+		ufs_1_phy: phy@17f04000 {
+			compatible = "samsung,exynosautov9-ufs-phy";
+			reg = <0x17f04000 0xc00>;
+			reg-names = "phy-pma";
+			samsung,pmu-syscon = <&pmu_system_controller 0x72c>;
+			#phy-cells = <0>;
+			clocks = <&xtcxo>;
+			clock-names = "ref_clk";
+			status = "disabled";
+		};
+
+		ufs_1: ufs@17f00000 {
+			compatible = "samsung,exynosautov9-ufs";
+
+			reg = <0x17f00000 0x100>,
+			      <0x17f01100 0x410>,
+			      <0x17f80000 0x8000>,
+			      <0x17de0000 0x2200>;
+			reg-names = "hci", "vs_hci", "unipro", "ufsp";
+			interrupts = <GIC_SPI 235 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cmu_fsys2 CLK_GOUT_FSYS2_UFS_EMBD1_ACLK>,
+				 <&cmu_fsys2 CLK_GOUT_FSYS2_UFS_EMBD1_UNIPRO>;
+			clock-names = "core_clk", "sclk_unipro_main";
+			freq-table-hz = <0 0>, <0 0>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&ufs_rst_n_1 &ufs_refclk_out_1>;
+			phys = <&ufs_1_phy>;
+			phy-names = "ufs-phy";
+			samsung,sysreg = <&syscon_fsys2 0x714>;
+			status = "disabled";
+		};
+
+		watchdog_cl0: watchdog@10050000 {
+			compatible = "samsung,exynosautov9-wdt";
+			reg = <0x10050000 0x100>;
+			interrupts = <GIC_SPI 476 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cmu_peris CLK_GOUT_WDT_CLUSTER0>, <&xtcxo>;
+			clock-names = "watchdog", "watchdog_src";
+			samsung,syscon-phandle = <&pmu_system_controller>;
+			samsung,cluster-index = <0>;
+		};
+
+		watchdog_cl1: watchdog@10060000 {
+			compatible = "samsung,exynosautov9-wdt";
+			reg = <0x10060000 0x100>;
+			interrupts = <GIC_SPI 475 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cmu_peris CLK_GOUT_WDT_CLUSTER1>, <&xtcxo>;
+			clock-names = "watchdog", "watchdog_src";
+			samsung,syscon-phandle = <&pmu_system_controller>;
+			samsung,cluster-index = <1>;
+		};
 	};
 };
 
diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index a14a6173b765..3ea9edc87909 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -1,4 +1,5 @@
 # SPDX-License-Identifier: GPL-2.0
+
 dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1012a-frdm.dtb
 dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1012a-frwy.dtb
 dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1012a-oxalis.dtb
@@ -22,6 +23,7 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1088a-rdb.dtb
 dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1088a-ten64.dtb
 dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-qds.dtb
 dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-rdb.dtb
+dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2081a-rdb.dtb
 dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2080a-simu.dtb
 dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2088a-qds.dtb
 dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls2088a-rdb.dtb
@@ -33,26 +35,66 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-qds.dtb
 dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-rdb.dtb
 dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2162a-qds.dtb
 
+fsl-ls1028a-qds-13bb-dtbs := fsl-ls1028a-qds.dtb fsl-ls1028a-qds-13bb.dtbo
+fsl-ls1028a-qds-65bb-dtbs := fsl-ls1028a-qds.dtb fsl-ls1028a-qds-65bb.dtbo
+fsl-ls1028a-qds-7777-dtbs := fsl-ls1028a-qds.dtb fsl-ls1028a-qds-7777.dtbo
+fsl-ls1028a-qds-85bb-dtbs := fsl-ls1028a-qds.dtb fsl-ls1028a-qds-85bb.dtbo
+fsl-ls1028a-qds-899b-dtbs := fsl-ls1028a-qds.dtb fsl-ls1028a-qds-899b.dtbo
+fsl-ls1028a-qds-9999-dtbs := fsl-ls1028a-qds.dtb fsl-ls1028a-qds-9999.dtbo
+
+dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1028a-qds-13bb.dtb
+dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1028a-qds-65bb.dtb
+dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1028a-qds-7777.dtb
+dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1028a-qds-85bb.dtb
+dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1028a-qds-899b.dtb
+dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-ls1028a-qds-9999.dtb
+
+dtb-$(CONFIG_ARCH_MXC) += imx8dxl-evk.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-beacon-kit.dtb
-dtb-$(CONFIG_ARCH_MXC) += imx8mm-evk.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mm-data-modul-edm-sbc.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-ddr4-evk.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mm-emcon-avari.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mm-evk.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-icore-mx8mm-ctouch2.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-icore-mx8mm-edimm2.2.dtb
-dtb-$(CONFIG_ARCH_MXC) += imx8mm-kontron-n801x-s.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mm-kontron-bl.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mm-kontron-bl-osm-s.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mm-mx8menlo.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-nitrogen-r2.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mm-phyboard-polis-rdk.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mm-tqma8mqml-mba8mx.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-var-som-symphony.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw71xx-0x.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw72xx-0x.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw73xx-0x.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw7901.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw7902.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw7903.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw7904.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mm-verdin-nonwifi-dahlia.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mm-verdin-nonwifi-dev.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mm-verdin-wifi-dahlia.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mm-verdin-wifi-dev.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mn-beacon-kit.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mn-bsh-smm-s2.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mn-bsh-smm-s2pro.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mn-evk.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mn-ddr3l-evk.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mn-ddr4-evk.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mn-tqma8mqnl-mba8mx.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mn-var-som-symphony.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mn-venice-gw7902.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mp-dhcom-pdk2.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mp-evk.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mp-icore-mx8mp-edimm2.2.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mp-msc-sm2s-ep1.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mp-phyboard-pollux-rdk.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mp-tqma8mpql-mba8mpxl.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mp-venice-gw74xx.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mp-verdin-nonwifi-dahlia.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mp-verdin-nonwifi-dev.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mp-verdin-wifi-dahlia.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mp-verdin-wifi-dev.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mq-evk.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mq-hummingboard-pulse.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mq-kontron-pitx-imx8m.dtb
@@ -60,6 +102,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5-devkit.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5-r2.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5-r3.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5-r4.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mq-tqma8mq-mba8mx.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mq-mnt-reform2.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mq-nitrogen.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mq-phanbell.dtb
@@ -71,6 +114,26 @@ dtb-$(CONFIG_ARCH_MXC) += imx8qm-mek.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8qxp-ai_ml.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8qxp-colibri-eval-v3.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8qxp-mek.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8ulp-evk.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx93-11x11-evk.dtb
+
+imx8mm-venice-gw72xx-0x-imx219-dtbs	:= imx8mm-venice-gw73xx-0x.dtb imx8mm-venice-gw73xx-0x-imx219.dtbo
+imx8mm-venice-gw72xx-0x-rs232-rts-dtbs	:= imx8mm-venice-gw72xx-0x.dtb imx8mm-venice-gw72xx-0x-rs232-rts.dtbo
+imx8mm-venice-gw72xx-0x-rs422-dtbs	:= imx8mm-venice-gw72xx-0x.dtb imx8mm-venice-gw72xx-0x-rs422.dtbo
+imx8mm-venice-gw72xx-0x-rs485-dtbs	:= imx8mm-venice-gw72xx-0x.dtb imx8mm-venice-gw72xx-0x-rs485.dtbo
+imx8mm-venice-gw73xx-0x-imx219-dtbs	:= imx8mm-venice-gw73xx-0x.dtb imx8mm-venice-gw73xx-0x-imx219.dtbo
+imx8mm-venice-gw73xx-0x-rs232-rts-dtbs	:= imx8mm-venice-gw73xx-0x.dtb imx8mm-venice-gw73xx-0x-rs232-rts.dtbo
+imx8mm-venice-gw73xx-0x-rs422-dtbs	:= imx8mm-venice-gw73xx-0x.dtb imx8mm-venice-gw73xx-0x-rs422.dtbo
+imx8mm-venice-gw73xx-0x-rs485-dtbs	:= imx8mm-venice-gw73xx-0x.dtb imx8mm-venice-gw73xx-0x-rs485.dtbo
+
+dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw72xx-0x-imx219.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw72xx-0x-rs232-rts.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw72xx-0x-rs422.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw72xx-0x-rs485.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw73xx-0x-imx219.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw73xx-0x-rs232-rts.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw73xx-0x-rs422.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mm-venice-gw73xx-0x-rs485.dtb
 
 dtb-$(CONFIG_ARCH_S32) += s32g274a-evb.dtb
 dtb-$(CONFIG_ARCH_S32) += s32g274a-rdb2.dtb
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1012a-qds.dts b/arch/arm64/boot/dts/freescale/fsl-ls1012a-qds.dts
index e22c5e77fecd..5a8d85a7d161 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls1012a-qds.dts
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1012a-qds.dts
@@ -69,7 +69,7 @@
 	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		compatible = "n25q128a11", "jedec,spi-nor";
+		compatible = "micron,n25q128a11", "jedec,spi-nor";
 		reg = <0>;
 		spi-max-frequency = <10000000>;
 	};
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi
index 50a72cda4727..a863022529ac 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi
@@ -204,7 +204,7 @@
 				compatible = "fsl,sec-v5.4-job-ring",
 					     "fsl,sec-v5.0-job-ring",
 					     "fsl,sec-v4.0-job-ring";
-				reg	   = <0x10000 0x10000>;
+				reg = <0x10000 0x10000>;
 				interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
 			};
 
@@ -212,7 +212,7 @@
 				compatible = "fsl,sec-v5.4-job-ring",
 					     "fsl,sec-v5.0-job-ring",
 					     "fsl,sec-v4.0-job-ring";
-				reg	   = <0x20000 0x10000>;
+				reg = <0x20000 0x10000>;
 				interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
 			};
 
@@ -220,7 +220,7 @@
 				compatible = "fsl,sec-v5.4-job-ring",
 					     "fsl,sec-v5.0-job-ring",
 					     "fsl,sec-v4.0-job-ring";
-				reg	   = <0x30000 0x10000>;
+				reg = <0x30000 0x10000>;
 				interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
 			};
 
@@ -228,7 +228,7 @@
 				compatible = "fsl,sec-v5.4-job-ring",
 					     "fsl,sec-v5.0-job-ring",
 					     "fsl,sec-v4.0-job-ring";
-				reg	   = <0x40000 0x10000>;
+				reg = <0x40000 0x10000>;
 				interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
 			};
 
@@ -271,6 +271,14 @@
 			};
 		};
 
+		sfp: efuse@1e80000 {
+			compatible = "fsl,ls1021a-sfp";
+			reg = <0x0 0x1e80000 0x0 0x10000>;
+			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
+					    QORIQ_CLK_PLL_DIV(4)>;
+			clock-names = "sfp";
+		};
+
 		sec_mon: sec_mon@1e90000 {
 			compatible = "fsl,sec-v5.4-mon", "fsl,sec-v5.0-mon",
 				     "fsl,sec-v4.0-mon";
@@ -465,7 +473,7 @@
 			status = "disabled";
 		};
 
-		edma0: edma@2c00000 {
+		edma0: dma-controller@2c00000 {
 			#dma-cells = <2>;
 			compatible = "fsl,vf610-edma";
 			reg = <0x0 0x2c00000 0x0 0x10000>,
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-kbox-a-230-ls.dts b/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-kbox-a-230-ls.dts
index 6b575efd84a7..73eb6061c73e 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-kbox-a-230-ls.dts
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-kbox-a-230-ls.dts
@@ -59,6 +59,10 @@
 	status = "okay";
 };
 
+&enetc_port3 {
+	status = "okay";
+};
+
 &i2c3 {
 	eeprom@57 {
 		compatible = "atmel,24c32";
@@ -104,7 +108,10 @@
 };
 
 &mscc_felix_port4 {
-	ethernet = <&enetc_port2>;
+	status = "okay";
+};
+
+&mscc_felix_port5 {
 	status = "okay";
 };
 
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28-var2.dts b/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28-var2.dts
index 330e34f933a3..113b1df74bf8 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28-var2.dts
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28-var2.dts
@@ -39,6 +39,10 @@
 	status = "okay";
 };
 
+&enetc_port3 {
+	status = "okay";
+};
+
 &mscc_felix {
 	status = "okay";
 };
@@ -60,6 +64,9 @@
 };
 
 &mscc_felix_port4 {
-	ethernet = <&enetc_port2>;
+	status = "okay";
+};
+
+&mscc_felix_port5 {
 	status = "okay";
 };
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28.dts b/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28.dts
index d74e738e4070..4ab17b984b03 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28.dts
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a-kontron-sl28.dts
@@ -157,6 +157,10 @@
 	};
 };
 
+&ftm_alarm0 {
+	status = "okay";
+};
+
 &gpio1 {
 	gpio-line-names =
 		"", "", "", "", "", "", "", "",
@@ -307,10 +311,19 @@
 	status = "okay";
 };
 
+&mscc_felix_port4 {
+	dsa-tag-protocol = "ocelot-8021q";
+};
+
+&mscc_felix_port5 {
+	dsa-tag-protocol = "ocelot-8021q";
+};
+
 &usb0 {
 	status = "okay";
 };
 
 &usb1 {
+	dr_mode = "host";
 	status = "okay";
 };
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds-13bb.dts b/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds-13bb.dts
new file mode 100644
index 000000000000..f826392c23fa
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds-13bb.dts
@@ -0,0 +1,91 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device Tree fragment for LS1028A QDS board, serdes 13bb
+ *
+ * Copyright 2019-2021 NXP
+ *
+ * Requires a LS1028A QDS board with lane B rework.
+ * Requires a SCH-30841 card with lane A of connector rewired to PHY lane C.
+ * Set-up is a SCH-30842 card in slot 1 and SCH-30841 in slot 2.
+ */
+
+/dts-v1/;
+/plugin/;
+
+&mdio_slot1 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	slot1_sgmii: ethernet-phy@2 {
+		/* AQR112 */
+		reg = <0x2>;
+		compatible = "ethernet-phy-ieee802.3-c45";
+	};
+};
+
+&enetc_port0 {
+	phy-handle = <&slot1_sgmii>;
+	phy-mode = "usxgmii";
+	managed = "in-band-status";
+	status = "okay";
+};
+
+&mdio_slot2 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	/* 4 ports on AQR412 */
+	slot2_qxgmii0: ethernet-phy@0 {
+		reg = <0x0>;
+		compatible = "ethernet-phy-ieee802.3-c45";
+	};
+
+	slot2_qxgmii1: ethernet-phy@1 {
+		reg = <0x1>;
+		compatible = "ethernet-phy-ieee802.3-c45";
+	};
+
+	slot2_qxgmii2: ethernet-phy@2 {
+		reg = <0x2>;
+		compatible = "ethernet-phy-ieee802.3-c45";
+	};
+
+	slot2_qxgmii3: ethernet-phy@3 {
+		reg = <0x3>;
+		compatible = "ethernet-phy-ieee802.3-c45";
+	};
+};
+
+&mscc_felix_ports {
+	port@0 {
+		status = "okay";
+		phy-handle = <&slot2_qxgmii0>;
+		phy-mode = "usxgmii";
+		managed = "in-band-status";
+	};
+
+	port@1 {
+		status = "okay";
+		phy-handle = <&slot2_qxgmii1>;
+		phy-mode = "usxgmii";
+		managed = "in-band-status";
+	};
+
+	port@2 {
+		status = "okay";
+		phy-handle = <&slot2_qxgmii2>;
+		phy-mode = "usxgmii";
+		managed = "in-band-status";
+	};
+
+	port@3 {
+		status = "okay";
+		phy-handle = <&slot2_qxgmii3>;
+		phy-mode = "usxgmii";
+		managed = "in-band-status";
+	};
+};
+
+&mscc_felix {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds-65bb.dts b/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds-65bb.dts
new file mode 100644
index 000000000000..b949cac03742
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds-65bb.dts
@@ -0,0 +1,85 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device Tree fragment for LS1028A QDS board, serdes 69xx
+ *
+ * Copyright 2019-2021 NXP
+ *
+ * Requires a LS1028A QDS board with lane B rework.
+ * Requires a SCH-30842 card in slot 1 and a SCH-28021 card in slot 2.
+ */
+
+/dts-v1/;
+/plugin/;
+
+&mdio_slot1 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	slot1_sgmii: ethernet-phy@2 {
+		/* AQR112 */
+		reg = <0x2>;
+		compatible = "ethernet-phy-ieee802.3-c45";
+	};
+};
+
+&enetc_port0 {
+	phy-handle = <&slot1_sgmii>;
+	phy-mode = "2500base-x";
+	status = "okay";
+};
+
+&mdio_slot2 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	/* 4 ports on VSC8514 */
+	slot2_qsgmii0: ethernet-phy@8 {
+		reg = <0x8>;
+	};
+
+	slot2_qsgmii1: ethernet-phy@9 {
+		reg = <0x9>;
+	};
+
+	slot2_qsgmii2: ethernet-phy@a {
+		reg = <0xa>;
+	};
+
+	slot2_qsgmii3: ethernet-phy@b {
+		reg = <0xb>;
+	};
+};
+
+&mscc_felix_ports {
+	port@0 {
+		status = "okay";
+		phy-handle = <&slot2_qsgmii0>;
+		phy-mode = "qsgmii";
+		managed = "in-band-status";
+	};
+
+	port@1 {
+		status = "okay";
+		phy-handle = <&slot2_qsgmii1>;
+		phy-mode = "qsgmii";
+		managed = "in-band-status";
+	};
+
+	port@2 {
+		status = "okay";
+		phy-handle = <&slot2_qsgmii2>;
+		phy-mode = "qsgmii";
+		managed = "in-band-status";
+	};
+
+	port@3 {
+		status = "okay";
+		phy-handle = <&slot2_qsgmii3>;
+		phy-mode = "qsgmii";
+		managed = "in-band-status";
+	};
+};
+
+&mscc_felix {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds-7777.dts b/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds-7777.dts
new file mode 100644
index 000000000000..1dff68d7484b
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds-7777.dts
@@ -0,0 +1,69 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device Tree fragment for LS1028A QDS board, serdes 7777
+ *
+ * Copyright 2019-2021 NXP
+ *
+ * Requires a LS1028A QDS board without lane B rework.
+ * Requires a SCH-30841 card without lane A/C rewire and with a FW with muxing
+ * disabled, plugged in slot 1.
+ */
+
+/dts-v1/;
+/plugin/;
+
+&mdio_slot1 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	/* 4 ports on AQR412 */
+	slot1_sxgmii0: ethernet-phy@0 {
+		reg = <0x0>;
+		compatible = "ethernet-phy-ieee802.3-c45";
+	};
+
+	slot1_sxgmii1: ethernet-phy@1 {
+		reg = <0x1>;
+		compatible = "ethernet-phy-ieee802.3-c45";
+	};
+
+	slot1_sxgmii2: ethernet-phy@2 {
+		reg = <0x2>;
+		compatible = "ethernet-phy-ieee802.3-c45";
+	};
+
+	slot1_sxgmii3: ethernet-phy@3 {
+		reg = <0x3>;
+		compatible = "ethernet-phy-ieee802.3-c45";
+	};
+};
+
+&mscc_felix_ports {
+	port@0 {
+		status = "okay";
+		phy-handle = <&slot1_sxgmii0>;
+		phy-mode = "2500base-x";
+	};
+
+	port@1 {
+		status = "okay";
+		phy-handle = <&slot1_sxgmii1>;
+		phy-mode = "2500base-x";
+	};
+
+	port@2 {
+		status = "okay";
+		phy-handle = <&slot1_sxgmii2>;
+		phy-mode = "2500base-x";
+	};
+
+	port@3 {
+		status = "okay";
+		phy-handle = <&slot1_sxgmii3>;
+		phy-mode = "2500base-x";
+	};
+};
+
+&mscc_felix {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds-85bb.dts b/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds-85bb.dts
new file mode 100644
index 000000000000..19424d349713
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds-85bb.dts
@@ -0,0 +1,85 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device Tree fragment for LS1028A QDS board, serdes 85bb
+ *
+ * Copyright 2019-2021 NXP
+ *
+ * Requires a LS1028A QDS board with lane B rework.
+ * Requires a SCH-24801 card in slot 1 and a SCH-28021 card in slot 2.
+ */
+
+/dts-v1/;
+/plugin/;
+
+&mdio_slot1 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	slot1_sgmii: ethernet-phy@1c {
+		/* 1st port on VSC8234 */
+		reg = <0x1c>;
+	};
+};
+
+&enetc_port0 {
+	phy-handle = <&slot1_sgmii>;
+	phy-mode = "sgmii";
+	managed = "in-band-status";
+	status = "okay";
+};
+
+&mdio_slot2 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	/* 4 ports on VSC8514 */
+	slot2_qsgmii0: ethernet-phy@8 {
+		reg = <0x8>;
+	};
+
+	slot2_qsgmii1: ethernet-phy@9 {
+		reg = <0x9>;
+	};
+
+	slot2_qsgmii2: ethernet-phy@a {
+		reg = <0xa>;
+	};
+
+	slot2_qsgmii3: ethernet-phy@b {
+		reg = <0xb>;
+	};
+};
+
+&mscc_felix_ports {
+	port@0 {
+		status = "okay";
+		phy-handle = <&slot2_qsgmii0>;
+		phy-mode = "qsgmii";
+		managed = "in-band-status";
+	};
+
+	port@1 {
+		status = "okay";
+		phy-handle = <&slot2_qsgmii1>;
+		phy-mode = "qsgmii";
+		managed = "in-band-status";
+	};
+
+	port@2 {
+		status = "okay";
+		phy-handle = <&slot2_qsgmii2>;
+		phy-mode = "qsgmii";
+		managed = "in-band-status";
+	};
+
+	port@3 {
+		status = "okay";
+		phy-handle = <&slot2_qsgmii3>;
+		phy-mode = "qsgmii";
+		managed = "in-band-status";
+	};
+};
+
+&mscc_felix {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds-899b.dts b/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds-899b.dts
new file mode 100644
index 000000000000..fb85847f778f
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds-899b.dts
@@ -0,0 +1,61 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device Tree fragment for LS1028A QDS board, serdes 85xx
+ *
+ * Copyright 2019-2021 NXP
+ *
+ * Requires a LS1028A QDS board without lane B rework.
+ * Requires a SCH-24801 card in slot 1.
+ */
+
+/dts-v1/;
+/plugin/;
+
+&mdio_slot1 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	/* VSC8234 */
+	slot1_sgmii0: ethernet-phy@1c {
+		reg = <0x1c>;
+	};
+
+	slot1_sgmii1: ethernet-phy@1d {
+		reg = <0x1d>;
+	};
+
+	slot1_sgmii2: ethernet-phy@1e {
+		reg = <0x1e>;
+	};
+
+	slot1_sgmii3: ethernet-phy@1f {
+		reg = <0x1f>;
+	};
+};
+
+&enetc_port0 {
+	phy-handle = <&slot1_sgmii0>;
+	phy-mode = "sgmii";
+	managed = "in-band-status";
+	status = "okay";
+};
+
+&mscc_felix_ports {
+	port@1 {
+		status = "okay";
+		phy-handle = <&slot1_sgmii1>;
+		phy-mode = "sgmii";
+		managed = "in-band-status";
+	};
+
+	port@2 {
+		status = "okay";
+		phy-handle = <&slot1_sgmii2>;
+		phy-mode = "sgmii";
+		managed = "in-band-status";
+	};
+};
+
+&mscc_felix {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds-9999.dts b/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds-9999.dts
new file mode 100644
index 000000000000..63e46fad22bd
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds-9999.dts
@@ -0,0 +1,68 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device Tree fragment for LS1028A QDS board, serdes 85xx
+ *
+ * Copyright 2019-2021 NXP
+ *
+ * Requires a LS1028A QDS board without lane B rework.
+ * Requires a SCH-24801 card in slot 1.
+ */
+
+/dts-v1/;
+/plugin/;
+
+&mdio_slot1 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	/* VSC8234 */
+	slot1_sgmii0: ethernet-phy@1c {
+		reg = <0x1c>;
+	};
+
+	slot1_sgmii1: ethernet-phy@1d {
+		reg = <0x1d>;
+	};
+
+	slot1_sgmii2: ethernet-phy@1e {
+		reg = <0x1e>;
+	};
+
+	slot1_sgmii3: ethernet-phy@1f {
+		reg = <0x1f>;
+	};
+};
+
+&mscc_felix_ports {
+	port@0 {
+		status = "okay";
+		phy-handle = <&slot1_sgmii0>;
+		phy-mode = "sgmii";
+		managed = "in-band-status";
+	};
+
+	port@1 {
+		status = "okay";
+		phy-handle = <&slot1_sgmii1>;
+		phy-mode = "sgmii";
+		managed = "in-band-status";
+	};
+
+	port@2 {
+		status = "okay";
+		phy-handle = <&slot1_sgmii2>;
+		phy-mode = "sgmii";
+		managed = "in-band-status";
+	};
+
+	port@3 {
+		status = "okay";
+		phy-handle = <&slot1_sgmii3>;
+		phy-mode = "sgmii";
+		managed = "in-band-status";
+	};
+};
+
+&mscc_felix {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts b/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts
index 6e2a1da662fb..0bb2f28a0441 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a-qds.dts
@@ -25,7 +25,7 @@
 		serial1 = &duart1;
 		mmc0 = &esdhc;
 		mmc1 = &esdhc1;
-		rtc1 = &ftm_alarm0;
+		rtc1 = &ftm_alarm1;
 	};
 
 	chosen {
@@ -93,7 +93,7 @@
 		compatible = "mdio-mux-multiplexer";
 		mux-controls = <&mux 0>;
 		mdio-parent-bus = <&enetc_mdio_pf3>;
-		#address-cells=<1>;
+		#address-cells = <1>;
 		#size-cells = <0>;
 
 		/* on-board RGMII PHY */
@@ -107,6 +107,30 @@
 				reg = <5>;
 			};
 		};
+
+		mdio_slot1: mdio@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+		};
+
+		mdio_slot2: mdio@5 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <5>;
+		};
+
+		mdio_slot3: mdio@6 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <6>;
+		};
+
+		mdio_slot4: mdio@7 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <7>;
+		};
 	};
 };
 
@@ -211,6 +235,16 @@
 	status = "okay";
 };
 
+&enetc_port1 {
+	phy-handle = <&qds_phy1>;
+	phy-mode = "rgmii-id";
+	status = "okay";
+};
+
+&enetc_port2 {
+	status = "okay";
+};
+
 &esdhc {
 	status = "okay";
 };
@@ -234,6 +268,10 @@
 	};
 };
 
+&ftm_alarm1 {
+	status = "okay";
+};
+
 &i2c0 {
 	status = "okay";
 
@@ -272,11 +310,6 @@
 				vcc-supply = <&sb_3v3>;
 			};
 
-			rtc@51 {
-				compatible = "nxp,pcf2129";
-				reg = <0x51>;
-			};
-
 			eeprom@56 {
 				compatible = "atmel,24c512";
 				reg = <0x56>;
@@ -318,16 +351,28 @@
 
 };
 
-&enetc_port1 {
-	phy-handle = <&qds_phy1>;
-	phy-mode = "rgmii-id";
+&i2c1 {
 	status = "okay";
+
+	rtc@51 {
+		compatible = "nxp,pcf2129";
+		reg = <0x51>;
+	};
 };
 
 &lpuart0 {
 	status = "okay";
 };
 
+&lpuart1 {
+	status = "okay";
+};
+
+&mscc_felix_port4 {
+	ethernet = <&enetc_port2>;
+	status = "okay";
+};
+
 &sai1 {
 	status = "okay";
 };
@@ -337,9 +382,11 @@
 };
 
 &usb0 {
+	dr_mode = "host";
 	status = "okay";
 };
 
 &usb1 {
+	dr_mode = "host";
 	status = "okay";
 };
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts b/arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts
index 7719f44bcaed..ecd2c1ea177f 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a-rdb.dts
@@ -2,7 +2,7 @@
 /*
  * Device Tree file for NXP LS1028A RDB Board.
  *
- * Copyright 2018 NXP
+ * Copyright 2018-2021 NXP
  *
  * Harninder Rai <harninder.rai@nxp.com>
  *
@@ -21,7 +21,17 @@
 		serial1 = &duart1;
 		mmc0 = &esdhc;
 		mmc1 = &esdhc1;
-		rtc1 = &ftm_alarm0;
+		rtc1 = &ftm_alarm1;
+		spi0 = &fspi;
+		ethernet0 = &enetc_port0;
+		ethernet1 = &enetc_port2;
+		ethernet2 = &mscc_felix_port0;
+		ethernet3 = &mscc_felix_port1;
+		ethernet4 = &mscc_felix_port2;
+		ethernet5 = &mscc_felix_port3;
+		ethernet6 = &mscc_felix_port4;
+		ethernet7 = &mscc_felix_port5;
+		ethernet8 = &enetc_port3;
 	};
 
 	chosen {
@@ -102,6 +112,52 @@
 	};
 };
 
+&duart0 {
+	status = "okay";
+};
+
+&duart1 {
+	status = "okay";
+};
+
+&enetc_mdio_pf3 {
+	sgmii_phy0: ethernet-phy@2 {
+		reg = <0x2>;
+	};
+
+	/* VSC8514 QSGMII quad PHY */
+	qsgmii_phy0: ethernet-phy@10 {
+		reg = <0x10>;
+	};
+
+	qsgmii_phy1: ethernet-phy@11 {
+		reg = <0x11>;
+	};
+
+	qsgmii_phy2: ethernet-phy@12 {
+		reg = <0x12>;
+	};
+
+	qsgmii_phy3: ethernet-phy@13 {
+		reg = <0x13>;
+	};
+};
+
+&enetc_port0 {
+	phy-handle = <&sgmii_phy0>;
+	phy-mode = "sgmii";
+	managed = "in-band-status";
+	status = "okay";
+};
+
+&enetc_port2 {
+	status = "okay";
+};
+
+&enetc_port3 {
+	status = "okay";
+};
+
 &esdhc {
 	sd-uhs-sdr104;
 	sd-uhs-sdr50;
@@ -132,6 +188,10 @@
 	};
 };
 
+&ftm_alarm1 {
+	status = "okay";
+};
+
 &i2c0 {
 	status = "okay";
 
@@ -188,48 +248,6 @@
 	};
 };
 
-&duart0 {
-	status = "okay";
-};
-
-&duart1 {
-	status = "okay";
-};
-
-&enetc_mdio_pf3 {
-	sgmii_phy0: ethernet-phy@2 {
-		reg = <0x2>;
-	};
-
-	/* VSC8514 QSGMII quad PHY */
-	qsgmii_phy0: ethernet-phy@10 {
-		reg = <0x10>;
-	};
-
-	qsgmii_phy1: ethernet-phy@11 {
-		reg = <0x11>;
-	};
-
-	qsgmii_phy2: ethernet-phy@12 {
-		reg = <0x12>;
-	};
-
-	qsgmii_phy3: ethernet-phy@13 {
-		reg = <0x13>;
-	};
-};
-
-&enetc_port0 {
-	phy-handle = <&sgmii_phy0>;
-	phy-mode = "sgmii";
-	managed = "in-band-status";
-	status = "okay";
-};
-
-&enetc_port2 {
-	status = "okay";
-};
-
 &mscc_felix {
 	status = "okay";
 };
@@ -267,7 +285,10 @@
 };
 
 &mscc_felix_port4 {
-	ethernet = <&enetc_port2>;
+	status = "okay";
+};
+
+&mscc_felix_port5 {
 	status = "okay";
 };
 
@@ -275,6 +296,10 @@
 	status = "okay";
 };
 
+&pwm0 {
+	status = "okay";
+};
+
 &sai4 {
 	status = "okay";
 };
@@ -284,10 +309,10 @@
 };
 
 &usb0 {
+	dr_mode = "host";
 	status = "okay";
 };
 
 &usb1 {
-	dr_mode = "otg";
 	status = "okay";
 };
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi
index fd3f3e8bb6ce..ac1c3a7e5f7a 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi
@@ -66,6 +66,13 @@
 		};
 	};
 
+	rtc_clk: rtc-clk {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		clock-output-names = "rtc_clk";
+	};
+
 	sysclk: sysclk {
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
@@ -89,7 +96,7 @@
 	};
 
 	reboot {
-		compatible ="syscon-reboot";
+		compatible = "syscon-reboot";
 		regmap = <&rst>;
 		offset = <0>;
 		mask = <0x02>;
@@ -113,13 +120,13 @@
 	};
 
 	gic: interrupt-controller@6000000 {
-		compatible= "arm,gic-v3";
+		compatible = "arm,gic-v3";
 		#address-cells = <2>;
 		#size-cells = <2>;
 		ranges;
-		reg= <0x0 0x06000000 0 0x10000>, /* GIC Dist */
+		reg = <0x0 0x06000000 0 0x10000>, /* GIC Dist */
 			<0x0 0x06040000 0 0x40000>; /* GIC Redistributor */
-		#interrupt-cells= <3>;
+		#interrupt-cells = <3>;
 		interrupt-controller;
 		interrupts = <GIC_PPI 9 (GIC_CPU_MASK_RAW(0xf) |
 					 IRQ_TYPE_LEVEL_LOW)>;
@@ -217,6 +224,20 @@
 			little-endian;
 		};
 
+		sfp: efuse@1e80000 {
+			compatible = "fsl,ls1028a-sfp";
+			reg = <0x0 0x1e80000 0x0 0x10000>;
+			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
+					    QORIQ_CLK_PLL_DIV(4)>;
+			clock-names = "sfp";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			ls1028a_uid: unique-id@1c {
+				reg = <0x1c 0x8>;
+			};
+		};
+
 		scfg: syscon@1fc0000 {
 			compatible = "fsl,ls1028a-scfg", "syscon";
 			reg = <0x0 0x1fc0000 0x0 0x10000>;
@@ -581,7 +602,6 @@
 			compatible = "fsl,ls1028a-dwc3", "snps,dwc3";
 			reg = <0x0 0x3100000 0x0 0x10000>;
 			interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
-			dr_mode = "host";
 			snps,dis_rxdet_inp3_quirk;
 			snps,quirk-frame-length-adjustment = <0x20>;
 			snps,incr-burst-type-adjustment = <1>, <4>, <8>, <16>;
@@ -592,7 +612,6 @@
 			compatible = "fsl,ls1028a-dwc3", "snps,dwc3";
 			reg = <0x0 0x3110000 0x0 0x10000>;
 			interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>;
-			dr_mode = "host";
 			snps,dis_rxdet_inp3_quirk;
 			snps,quirk-frame-length-adjustment = <0x20>;
 			snps,incr-burst-type-adjustment = <1>, <4>, <8>, <16>;
@@ -637,6 +656,18 @@
 			status = "disabled";
 		};
 
+		pcie_ep1: pcie-ep@3400000 {
+			compatible = "fsl,ls1028a-pcie-ep","fsl,ls-pcie-ep";
+			reg = <0x00 0x03400000 0x0 0x00100000
+			       0x80 0x00000000 0x8 0x00000000>;
+			reg-names = "regs", "addr_space";
+			interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>; /* PME interrupt */
+			interrupt-names = "pme";
+			num-ib-windows = <6>;
+			num-ob-windows = <8>;
+			status = "disabled";
+		};
+
 		pcie2: pcie@3500000 {
 			compatible = "fsl,ls1028a-pcie";
 			reg = <0x00 0x03500000 0x0 0x00100000>, /* controller registers */
@@ -664,6 +695,18 @@
 			status = "disabled";
 		};
 
+		pcie_ep2: pcie-ep@3500000 {
+			compatible = "fsl,ls1028a-pcie-ep","fsl,ls-pcie-ep";
+			reg = <0x00 0x03500000 0x0 0x00100000
+			       0x88 0x00000000 0x8 0x00000000>;
+			reg-names = "regs", "addr_space";
+			interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>; /* PME interrupt */
+			interrupt-names = "pme";
+			num-ib-windows = <6>;
+			num-ob-windows = <8>;
+			status = "disabled";
+		};
+
 		smmu: iommu@5000000 {
 			compatible = "arm,mmu-500";
 			reg = <0 0x5000000 0 0x800000>;
@@ -729,28 +772,28 @@
 			sec_jr0: jr@10000 {
 				compatible = "fsl,sec-v5.0-job-ring",
 					     "fsl,sec-v4.0-job-ring";
-				reg	= <0x10000 0x10000>;
+				reg = <0x10000 0x10000>;
 				interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
 			};
 
 			sec_jr1: jr@20000 {
 				compatible = "fsl,sec-v5.0-job-ring",
 					     "fsl,sec-v4.0-job-ring";
-				reg	= <0x20000 0x10000>;
+				reg = <0x20000 0x10000>;
 				interrupts = <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>;
 			};
 
 			sec_jr2: jr@30000 {
 				compatible = "fsl,sec-v5.0-job-ring",
 					     "fsl,sec-v4.0-job-ring";
-				reg	= <0x30000 0x10000>;
+				reg = <0x30000 0x10000>;
 				interrupts = <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>;
 			};
 
 			sec_jr3: jr@40000 {
 				compatible = "fsl,sec-v5.0-job-ring",
 					     "fsl,sec-v4.0-job-ring";
-				reg	= <0x40000 0x10000>;
+				reg = <0x40000 0x10000>;
 				interrupts = <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>;
 			};
 		};
@@ -1084,7 +1127,7 @@
 				interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
 				status = "disabled";
 
-				ports {
+				mscc_felix_ports: ports {
 					#address-cells = <1>;
 					#size-cells = <0>;
 
@@ -1113,6 +1156,7 @@
 					mscc_felix_port4: port@4 {
 						reg = <4>;
 						phy-mode = "internal";
+						ethernet = <&enetc_port2>;
 						status = "disabled";
 
 						fixed-link {
@@ -1125,6 +1169,7 @@
 					mscc_felix_port5: port@5 {
 						reg = <5>;
 						phy-mode = "internal";
+						ethernet = <&enetc_port3>;
 						status = "disabled";
 
 						fixed-link {
@@ -1162,6 +1207,94 @@
 			reg = <0x01 0xf0800000 0x0 0x10000>;
 		};
 
+		pwm0: pwm@2800000 {
+			compatible = "fsl,vf610-ftm-pwm";
+			#pwm-cells = <3>;
+			reg = <0x0 0x2800000 0x0 0x10000>;
+			clock-names = "ftm_sys", "ftm_ext",
+				      "ftm_fix", "ftm_cnt_clk_en";
+			clocks = <&clockgen 4 1>, <&clockgen 4 1>,
+				 <&rtc_clk>, <&clockgen 4 1>;
+			status = "disabled";
+		};
+
+		pwm1: pwm@2810000 {
+			compatible = "fsl,vf610-ftm-pwm";
+			#pwm-cells = <3>;
+			reg = <0x0 0x2810000 0x0 0x10000>;
+			clock-names = "ftm_sys", "ftm_ext",
+				      "ftm_fix", "ftm_cnt_clk_en";
+			clocks = <&clockgen 4 1>, <&clockgen 4 1>,
+				 <&rtc_clk>, <&clockgen 4 1>;
+			status = "disabled";
+		};
+
+		pwm2: pwm@2820000 {
+			compatible = "fsl,vf610-ftm-pwm";
+			#pwm-cells = <3>;
+			reg = <0x0 0x2820000 0x0 0x10000>;
+			clock-names = "ftm_sys", "ftm_ext",
+				      "ftm_fix", "ftm_cnt_clk_en";
+			clocks = <&clockgen 4 1>, <&clockgen 4 1>,
+				 <&rtc_clk>, <&clockgen 4 1>;
+			status = "disabled";
+		};
+
+		pwm3: pwm@2830000 {
+			compatible = "fsl,vf610-ftm-pwm";
+			#pwm-cells = <3>;
+			reg = <0x0 0x2830000 0x0 0x10000>;
+			clock-names = "ftm_sys", "ftm_ext",
+				      "ftm_fix", "ftm_cnt_clk_en";
+			clocks = <&clockgen 4 1>, <&clockgen 4 1>,
+				 <&rtc_clk>, <&clockgen 4 1>;
+			status = "disabled";
+		};
+
+		pwm4: pwm@2840000 {
+			compatible = "fsl,vf610-ftm-pwm";
+			#pwm-cells = <3>;
+			reg = <0x0 0x2840000 0x0 0x10000>;
+			clock-names = "ftm_sys", "ftm_ext",
+				      "ftm_fix", "ftm_cnt_clk_en";
+			clocks = <&clockgen 4 1>, <&clockgen 4 1>,
+				 <&rtc_clk>, <&clockgen 4 1>;
+			status = "disabled";
+		};
+
+		pwm5: pwm@2850000 {
+			compatible = "fsl,vf610-ftm-pwm";
+			#pwm-cells = <3>;
+			reg = <0x0 0x2850000 0x0 0x10000>;
+			clock-names = "ftm_sys", "ftm_ext",
+				      "ftm_fix", "ftm_cnt_clk_en";
+			clocks = <&clockgen 4 1>, <&clockgen 4 1>,
+				 <&rtc_clk>, <&clockgen 4 1>;
+			status = "disabled";
+		};
+
+		pwm6: pwm@2860000 {
+			compatible = "fsl,vf610-ftm-pwm";
+			#pwm-cells = <3>;
+			reg = <0x0 0x2860000 0x0 0x10000>;
+			clock-names = "ftm_sys", "ftm_ext",
+				      "ftm_fix", "ftm_cnt_clk_en";
+			clocks = <&clockgen 4 1>, <&clockgen 4 1>,
+				 <&rtc_clk>, <&clockgen 4 1>;
+			status = "disabled";
+		};
+
+		pwm7: pwm@2870000 {
+			compatible = "fsl,vf610-ftm-pwm";
+			#pwm-cells = <3>;
+			reg = <0x0 0x2870000 0x0 0x10000>;
+			clock-names = "ftm_sys", "ftm_ext",
+				      "ftm_fix", "ftm_cnt_clk_en";
+			clocks = <&clockgen 4 1>, <&clockgen 4 1>,
+				 <&rtc_clk>, <&clockgen 4 1>;
+			status = "disabled";
+		};
+
 		rcpm: power-controller@1e34040 {
 			compatible = "fsl,ls1028a-rcpm", "fsl,qoriq-rcpm-2.1+";
 			reg = <0x0 0x1e34040 0x0 0x1c>;
@@ -1174,6 +1307,15 @@
 			reg = <0x0 0x2800000 0x0 0x10000>;
 			fsl,rcpm-wakeup = <&rcpm 0x0 0x0 0x0 0x0 0x4000 0x0 0x0>;
 			interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+
+		ftm_alarm1: timer@2810000 {
+			compatible = "fsl,ls1028a-ftm-alarm";
+			reg = <0x0 0x2810000 0x0 0x10000>;
+			fsl,rcpm-wakeup = <&rcpm 0x0 0x0 0x0 0x0 0x4000 0x0 0x0>;
+			interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
 		};
 	};
 
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1043a-qds.dts b/arch/arm64/boot/dts/freescale/fsl-ls1043a-qds.dts
index fea167d222cf..9b726c2a4842 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls1043a-qds.dts
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1043a-qds.dts
@@ -3,7 +3,7 @@
  * Device Tree Include file for Freescale Layerscape-1043A family SoC.
  *
  * Copyright 2014-2015 Freescale Semiconductor, Inc.
- * Copyright 2018 NXP
+ * Copyright 2018-2021 NXP
  *
  * Mingkai Hu <Mingkai.hu@freescale.com>
  */
@@ -24,6 +24,22 @@
 		serial1 = &duart1;
 		serial2 = &duart2;
 		serial3 = &duart3;
+		sgmii-riser-s1-p1 = &sgmii_phy_s1_p1;
+		sgmii-riser-s2-p1 = &sgmii_phy_s2_p1;
+		sgmii-riser-s3-p1 = &sgmii_phy_s3_p1;
+		sgmii-riser-s4-p1 = &sgmii_phy_s4_p1;
+		qsgmii-s1-p1 = &qsgmii_phy_s1_p1;
+		qsgmii-s1-p2 = &qsgmii_phy_s1_p2;
+		qsgmii-s1-p3 = &qsgmii_phy_s1_p3;
+		qsgmii-s1-p4 = &qsgmii_phy_s1_p4;
+		qsgmii-s2-p1 = &qsgmii_phy_s2_p1;
+		qsgmii-s2-p2 = &qsgmii_phy_s2_p2;
+		qsgmii-s2-p3 = &qsgmii_phy_s2_p3;
+		qsgmii-s2-p4 = &qsgmii_phy_s2_p4;
+		emi1-slot1 = &ls1043mdio_s1;
+		emi1-slot2 = &ls1043mdio_s2;
+		emi1-slot3 = &ls1043mdio_s3;
+		emi1-slot4 = &ls1043mdio_s4;
 	};
 
 	chosen {
@@ -62,8 +78,11 @@
 	};
 
 	fpga: board-control@2,0 {
-		compatible = "fsl,ls1043aqds-fpga", "fsl,fpga-qixis";
+		compatible = "fsl,ls1043aqds-fpga", "fsl,fpga-qixis", "simple-mfd";
 		reg = <0x2 0x0 0x0000100>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 2 0 0x100>;
 	};
 };
 
@@ -153,3 +172,153 @@
 };
 
 #include "fsl-ls1043-post.dtsi"
+
+&fman0 {
+	ethernet@e0000 {
+		phy-handle = <&qsgmii_phy_s2_p1>;
+		phy-connection-type = "sgmii";
+	};
+
+	ethernet@e2000 {
+		phy-handle = <&qsgmii_phy_s2_p2>;
+		phy-connection-type = "sgmii";
+	};
+
+	ethernet@e4000 {
+		phy-handle = <&rgmii_phy1>;
+		phy-connection-type = "rgmii";
+	};
+
+	ethernet@e6000 {
+		phy-handle = <&rgmii_phy2>;
+		phy-connection-type = "rgmii";
+	};
+
+	ethernet@e8000 {
+		phy-handle = <&qsgmii_phy_s2_p3>;
+		phy-connection-type = "sgmii";
+	};
+
+	ethernet@ea000 {
+		phy-handle = <&qsgmii_phy_s2_p4>;
+		phy-connection-type = "sgmii";
+	};
+
+	ethernet@f0000 { /* DTSEC9/10GEC1 */
+		fixed-link = <1 1 10000 0 0>;
+		phy-connection-type = "xgmii";
+	};
+};
+
+&fpga {
+	mdio-mux-emi1@54 {
+		compatible = "mdio-mux-mmioreg", "mdio-mux";
+		mdio-parent-bus = <&mdio0>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x54 1>;    /* BRDCFG4 */
+		mux-mask = <0xe0>; /* EMI1 */
+
+		/* On-board RGMII1 PHY */
+		ls1043mdio0: mdio@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			rgmii_phy1: ethernet-phy@1 { /* MAC3 */
+				reg = <0x1>;
+			};
+		};
+
+		/* On-board RGMII2 PHY */
+		ls1043mdio1: mdio@20 {
+			reg = <0x20>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			rgmii_phy2: ethernet-phy@2 { /* MAC4 */
+				reg = <0x2>;
+			};
+		};
+
+		/* Slot 1 */
+		ls1043mdio_s1: mdio@40 {
+			reg = <0x40>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			qsgmii_phy_s1_p1: ethernet-phy@4 {
+				reg = <0x4>;
+			};
+
+			qsgmii_phy_s1_p2: ethernet-phy@5 {
+				reg = <0x5>;
+			};
+
+			qsgmii_phy_s1_p3: ethernet-phy@6 {
+				reg = <0x6>;
+			};
+
+			qsgmii_phy_s1_p4: ethernet-phy@7 {
+				reg = <0x7>;
+			};
+
+			sgmii_phy_s1_p1: ethernet-phy@1c {
+				reg = <0x1c>;
+			};
+		};
+
+		/* Slot 2 */
+		ls1043mdio_s2: mdio@60 {
+			reg = <0x60>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			qsgmii_phy_s2_p1: ethernet-phy@8 {
+				reg = <0x8>;
+			};
+
+			qsgmii_phy_s2_p2: ethernet-phy@9 {
+				reg = <0x9>;
+			};
+
+			qsgmii_phy_s2_p3: ethernet-phy@a {
+				reg = <0xa>;
+			};
+
+			qsgmii_phy_s2_p4: ethernet-phy@b {
+				reg = <0xb>;
+			};
+
+			sgmii_phy_s2_p1: ethernet-phy@1c {
+				reg = <0x1c>;
+			};
+		};
+
+		/* Slot 3 */
+		ls1043mdio_s3: mdio@80 {
+			reg = <0x80>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			sgmii_phy_s3_p1: ethernet-phy@1c {
+				reg = <0x1c>;
+			};
+		};
+
+		/* Slot 4 */
+		ls1043mdio_s4: mdio@a0 {
+			reg = <0xa0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			sgmii_phy_s4_p1: ethernet-phy@1c {
+				reg = <0x1c>;
+			};
+		};
+	};
+};
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1043a-rdb.dts b/arch/arm64/boot/dts/freescale/fsl-ls1043a-rdb.dts
index 3516af4726a5..26f8540cb101 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls1043a-rdb.dts
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1043a-rdb.dts
@@ -29,23 +29,33 @@
 
 &i2c0 {
 	status = "okay";
+
 	ina220@40 {
 		compatible = "ti,ina220";
 		reg = <0x40>;
 		shunt-resistor = <1000>;
 	};
+
 	adt7461a@4c {
 		compatible = "adi,adt7461";
 		reg = <0x4c>;
 	};
+
+	rtc@51 {
+		compatible = "nxp,pcf85263";
+		reg = <0x51>;
+	};
+
 	eeprom@52 {
 		compatible = "atmel,24c512";
 		reg = <0x52>;
 	};
+
 	eeprom@53 {
 		compatible = "atmel,24c512";
 		reg = <0x53>;
 	};
+
 	rtc@68 {
 		compatible = "pericom,pt7c4338";
 		reg = <0x68>;
@@ -94,6 +104,8 @@
 		compatible = "n25q128a13", "jedec,spi-nor";  /* 16MB */
 		reg = <0>;
 		spi-max-frequency = <1000000>; /* input clock */
+		fsl,spi-cs-sck-delay = <100>;
+		fsl,spi-sck-cs-delay = <100>;
 	};
 
 	slic@2 {
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1043a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls1043a.dtsi
index 01b01e320411..704f72caddd3 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls1043a.dtsi
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1043a.dtsi
@@ -11,6 +11,7 @@
 #include <dt-bindings/clock/fsl,qoriq-clockgen.h>
 #include <dt-bindings/thermal/thermal.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/gpio/gpio.h>
 
 / {
 	compatible = "fsl,ls1043a";
@@ -144,7 +145,7 @@
 	};
 
 	reboot {
-		compatible ="syscon-reboot";
+		compatible = "syscon-reboot";
 		regmap = <&dcfg>;
 		offset = <0xb0>;
 		mask = <0x02>;
@@ -300,6 +301,8 @@
 		#address-cells = <2>;
 		#size-cells = <2>;
 		ranges;
+		dma-ranges = <0x0 0x0 0x0 0x0 0x10000 0x00000000>;
+		dma-coherent;
 
 		clockgen: clocking@1ee1000 {
 			compatible = "fsl,ls1043a-clockgen";
@@ -335,7 +338,7 @@
 					<9 0 &gic GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>,
 					<10 0 &gic GIC_SPI 150 IRQ_TYPE_LEVEL_HIGH>,
 					<11 0 &gic GIC_SPI 151 IRQ_TYPE_LEVEL_HIGH>;
-				interrupt-map-mask = <0xffffffff 0x0>;
+				interrupt-map-mask = <0xf 0x0>;
 			};
 		};
 
@@ -354,7 +357,7 @@
 				compatible = "fsl,sec-v5.4-job-ring",
 					     "fsl,sec-v5.0-job-ring",
 					     "fsl,sec-v4.0-job-ring";
-				reg	   = <0x10000 0x10000>;
+				reg = <0x10000 0x10000>;
 				interrupts = <0 71 0x4>;
 			};
 
@@ -362,7 +365,7 @@
 				compatible = "fsl,sec-v5.4-job-ring",
 					     "fsl,sec-v5.0-job-ring",
 					     "fsl,sec-v4.0-job-ring";
-				reg	   = <0x20000 0x10000>;
+				reg = <0x20000 0x10000>;
 				interrupts = <0 72 0x4>;
 			};
 
@@ -370,7 +373,7 @@
 				compatible = "fsl,sec-v5.4-job-ring",
 					     "fsl,sec-v5.0-job-ring",
 					     "fsl,sec-v4.0-job-ring";
-				reg	   = <0x30000 0x10000>;
+				reg = <0x30000 0x10000>;
 				interrupts = <0 73 0x4>;
 			};
 
@@ -378,19 +381,27 @@
 				compatible = "fsl,sec-v5.4-job-ring",
 					     "fsl,sec-v5.0-job-ring",
 					     "fsl,sec-v4.0-job-ring";
-				reg	   = <0x40000 0x10000>;
+				reg = <0x40000 0x10000>;
 				interrupts = <0 74 0x4>;
 			};
 		};
 
+		sfp: efuse@1e80000 {
+			compatible = "fsl,ls1021a-sfp";
+			reg = <0x0 0x1e80000 0x0 0x10000>;
+			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
+					    QORIQ_CLK_PLL_DIV(4)>;
+			clock-names = "sfp";
+		};
+
 		dcfg: dcfg@1ee0000 {
 			compatible = "fsl,ls1043a-dcfg", "syscon";
-			reg = <0x0 0x1ee0000 0x0 0x10000>;
+			reg = <0x0 0x1ee0000 0x0 0x1000>;
 			big-endian;
 		};
 
-		ifc: ifc@1530000 {
-			compatible = "fsl,ifc", "simple-bus";
+		ifc: memory-controller@1530000 {
+			compatible = "fsl,ifc";
 			reg = <0x0 0x1530000 0x0 0x10000>;
 			interrupts = <0 43 0x4>;
 		};
@@ -528,7 +539,7 @@
 		};
 
 		i2c0: i2c@2180000 {
-			compatible = "fsl,vf610-i2c";
+			compatible = "fsl,ls1043a-i2c", "fsl,vf610-i2c";
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <0x0 0x2180000 0x0 0x10000>;
@@ -536,14 +547,14 @@
 			clock-names = "i2c";
 			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
 					    QORIQ_CLK_PLL_DIV(1)>;
-			dmas = <&edma0 1 39>,
-			       <&edma0 1 38>;
-			dma-names = "tx", "rx";
+			dmas = <&edma0 1 38>,
+			       <&edma0 1 39>;
+			dma-names = "rx", "tx";
 			status = "disabled";
 		};
 
 		i2c1: i2c@2190000 {
-			compatible = "fsl,vf610-i2c";
+			compatible = "fsl,ls1043a-i2c", "fsl,vf610-i2c";
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <0x0 0x2190000 0x0 0x10000>;
@@ -551,11 +562,12 @@
 			clock-names = "i2c";
 			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
 					    QORIQ_CLK_PLL_DIV(1)>;
+			scl-gpios = <&gpio4 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 			status = "disabled";
 		};
 
 		i2c2: i2c@21a0000 {
-			compatible = "fsl,vf610-i2c";
+			compatible = "fsl,ls1043a-i2c", "fsl,vf610-i2c";
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <0x0 0x21a0000 0x0 0x10000>;
@@ -563,11 +575,12 @@
 			clock-names = "i2c";
 			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
 					    QORIQ_CLK_PLL_DIV(1)>;
+			scl-gpios = <&gpio4 10 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 			status = "disabled";
 		};
 
 		i2c3: i2c@21b0000 {
-			compatible = "fsl,vf610-i2c";
+			compatible = "fsl,ls1043a-i2c", "fsl,vf610-i2c";
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <0x0 0x21b0000 0x0 0x10000>;
@@ -575,6 +588,7 @@
 			clock-names = "i2c";
 			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
 					    QORIQ_CLK_PLL_DIV(1)>;
+			scl-gpios = <&gpio4 12 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 			status = "disabled";
 		};
 
@@ -784,7 +798,7 @@
 			big-endian;
 		};
 
-		edma0: edma@2c00000 {
+		edma0: dma-controller@2c00000 {
 			#dma-cells = <2>;
 			compatible = "fsl,vf610-edma";
 			reg = <0x0 0x2c00000 0x0 0x10000>,
@@ -802,48 +816,59 @@
 					    QORIQ_CLK_PLL_DIV(1)>;
 		};
 
-		usb0: usb@2f00000 {
-			compatible = "snps,dwc3";
-			reg = <0x0 0x2f00000 0x0 0x10000>;
-			interrupts = <0 60 0x4>;
-			dr_mode = "host";
-			snps,quirk-frame-length-adjustment = <0x20>;
-			snps,dis_rxdet_inp3_quirk;
-			snps,incr-burst-type-adjustment = <1>, <4>, <8>, <16>;
-			status = "disabled";
-		};
+		aux_bus: aux_bus {
+			#address-cells = <2>;
+			#size-cells = <2>;
+			compatible = "simple-bus";
+			ranges;
+			dma-ranges = <0x0 0x0 0x0 0x0 0x100 0x00000000>;
+
+			usb0: usb@2f00000 {
+				compatible = "snps,dwc3";
+				reg = <0x0 0x2f00000 0x0 0x10000>;
+				interrupts = <0 60 IRQ_TYPE_LEVEL_HIGH>;
+				dr_mode = "host";
+				snps,quirk-frame-length-adjustment = <0x20>;
+				snps,dis_rxdet_inp3_quirk;
+				usb3-lpm-capable;
+				snps,incr-burst-type-adjustment = <1>, <4>, <8>, <16>;
+				status = "disabled";
+			};
 
-		usb1: usb@3000000 {
-			compatible = "snps,dwc3";
-			reg = <0x0 0x3000000 0x0 0x10000>;
-			interrupts = <0 61 0x4>;
-			dr_mode = "host";
-			snps,quirk-frame-length-adjustment = <0x20>;
-			snps,dis_rxdet_inp3_quirk;
-			snps,incr-burst-type-adjustment = <1>, <4>, <8>, <16>;
-			status = "disabled";
-		};
+			usb1: usb@3000000 {
+				compatible = "snps,dwc3";
+				reg = <0x0 0x3000000 0x0 0x10000>;
+				interrupts = <0 61 IRQ_TYPE_LEVEL_HIGH>;
+				dr_mode = "host";
+				snps,quirk-frame-length-adjustment = <0x20>;
+				snps,dis_rxdet_inp3_quirk;
+				usb3-lpm-capable;
+				snps,incr-burst-type-adjustment = <1>, <4>, <8>, <16>;
+				status = "disabled";
+			};
 
-		usb2: usb@3100000 {
-			compatible = "snps,dwc3";
-			reg = <0x0 0x3100000 0x0 0x10000>;
-			interrupts = <0 63 0x4>;
-			dr_mode = "host";
-			snps,quirk-frame-length-adjustment = <0x20>;
-			snps,dis_rxdet_inp3_quirk;
-			snps,incr-burst-type-adjustment = <1>, <4>, <8>, <16>;
-			status = "disabled";
-		};
+			usb2: usb@3100000 {
+				compatible = "snps,dwc3";
+				reg = <0x0 0x3100000 0x0 0x10000>;
+				interrupts = <0 63 IRQ_TYPE_LEVEL_HIGH>;
+				dr_mode = "host";
+				snps,quirk-frame-length-adjustment = <0x20>;
+				snps,dis_rxdet_inp3_quirk;
+				usb3-lpm-capable;
+				snps,incr-burst-type-adjustment = <1>, <4>, <8>, <16>;
+				status = "disabled";
+			};
 
-		sata: sata@3200000 {
-			compatible = "fsl,ls1043a-ahci";
-			reg = <0x0 0x3200000 0x0 0x10000>,
-				<0x0 0x20140520 0x0 0x4>;
-			reg-names = "ahci", "sata-ecc";
-			interrupts = <0 69 0x4>;
-			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
-					    QORIQ_CLK_PLL_DIV(1)>;
-			dma-coherent;
+			sata: sata@3200000 {
+				compatible = "fsl,ls1043a-ahci";
+				reg = <0x0 0x3200000 0x0 0x10000>,
+					<0x0 0x20140520 0x0 0x4>;
+				reg-names = "ahci", "sata-ecc";
+				interrupts = <0 69 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
+						    QORIQ_CLK_PLL_DIV(1)>;
+				dma-coherent;
+			};
 		};
 
 		msi1: msi-controller1@1571000 {
@@ -872,13 +897,12 @@
 			reg = <0x00 0x03400000 0x0 0x00100000>, /* controller registers */
 			      <0x40 0x00000000 0x0 0x00002000>; /* configuration space */
 			reg-names = "regs", "config";
-			interrupts = <0 118 0x4>, /* controller interrupt */
-				     <0 117 0x4>; /* PME interrupt */
-			interrupt-names = "intr", "pme";
+			interrupts = <0 117 IRQ_TYPE_LEVEL_HIGH>,
+				     <0 118 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "pme", "aer";
 			#address-cells = <3>;
 			#size-cells = <2>;
 			device_type = "pci";
-			dma-coherent;
 			num-viewport = <6>;
 			bus-range = <0x0 0xff>;
 			ranges = <0x81000000 0x0 0x00000000 0x40 0x00010000 0x0 0x00010000   /* downstream I/O */
@@ -890,6 +914,8 @@
 					<0000 0 0 2 &gic 0 111 0x4>,
 					<0000 0 0 3 &gic 0 112 0x4>,
 					<0000 0 0 4 &gic 0 113 0x4>;
+			fsl,pcie-scfg = <&scfg 0>;
+			big-endian;
 			status = "disabled";
 		};
 
@@ -898,13 +924,12 @@
 			reg = <0x00 0x03500000 0x0 0x00100000>, /* controller registers */
 			      <0x48 0x00000000 0x0 0x00002000>; /* configuration space */
 			reg-names = "regs", "config";
-			interrupts = <0 128 0x4>,
-				     <0 127 0x4>;
-			interrupt-names = "intr", "pme";
+			interrupts = <0 127 IRQ_TYPE_LEVEL_HIGH>,
+				     <0 128 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "pme", "aer";
 			#address-cells = <3>;
 			#size-cells = <2>;
 			device_type = "pci";
-			dma-coherent;
 			num-viewport = <6>;
 			bus-range = <0x0 0xff>;
 			ranges = <0x81000000 0x0 0x00000000 0x48 0x00010000 0x0 0x00010000   /* downstream I/O */
@@ -916,6 +941,8 @@
 					<0000 0 0 2 &gic 0 121 0x4>,
 					<0000 0 0 3 &gic 0 122 0x4>,
 					<0000 0 0 4 &gic 0 123 0x4>;
+			fsl,pcie-scfg = <&scfg 1>;
+			big-endian;
 			status = "disabled";
 		};
 
@@ -924,13 +951,12 @@
 			reg = <0x00 0x03600000 0x0 0x00100000>, /* controller registers */
 			      <0x50 0x00000000 0x0 0x00002000>; /* configuration space */
 			reg-names = "regs", "config";
-			interrupts = <0 162 0x4>,
-				     <0 161 0x4>;
-			interrupt-names = "intr", "pme";
+			interrupts = <0 161 IRQ_TYPE_LEVEL_HIGH>,
+				     <0 162 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "pme", "aer";
 			#address-cells = <3>;
 			#size-cells = <2>;
 			device_type = "pci";
-			dma-coherent;
 			num-viewport = <6>;
 			bus-range = <0x0 0xff>;
 			ranges = <0x81000000 0x0 0x00000000 0x50 0x00010000 0x0 0x00010000   /* downstream I/O */
@@ -942,6 +968,8 @@
 					<0000 0 0 2 &gic 0 155 0x4>,
 					<0000 0 0 3 &gic 0 156 0x4>,
 					<0000 0 0 4 &gic 0 157 0x4>;
+			fsl,pcie-scfg = <&scfg 2>;
+			big-endian;
 			status = "disabled";
 		};
 
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1046a-qds.dts b/arch/arm64/boot/dts/freescale/fsl-ls1046a-qds.dts
index eec62c63dafe..b2fcbba60d3a 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls1046a-qds.dts
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1046a-qds.dts
@@ -3,7 +3,7 @@
  * Device Tree Include file for Freescale Layerscape-1046A family SoC.
  *
  * Copyright 2016 Freescale Semiconductor, Inc.
- * Copyright 2018 NXP
+ * Copyright 2018-2019 NXP
  *
  * Shaohui Xie <Shaohui.Xie@nxp.com>
  */
@@ -17,14 +17,26 @@
 	compatible = "fsl,ls1046a-qds", "fsl,ls1046a";
 
 	aliases {
+		emi1-slot1 = &ls1046mdio_s1;
+		emi1-slot2 = &ls1046mdio_s2;
+		emi1-slot4 = &ls1046mdio_s4;
 		gpio0 = &gpio0;
 		gpio1 = &gpio1;
 		gpio2 = &gpio2;
 		gpio3 = &gpio3;
+		qsgmii-s2-p1 = &qsgmii_phy_s2_p1;
+		qsgmii-s2-p2 = &qsgmii_phy_s2_p2;
+		qsgmii-s2-p3 = &qsgmii_phy_s2_p3;
+		qsgmii-s2-p4 = &qsgmii_phy_s2_p4;
 		serial0 = &duart0;
 		serial1 = &duart1;
 		serial2 = &duart2;
 		serial3 = &duart3;
+		sgmii-s1-p1 = &sgmii_phy_s1_p1;
+		sgmii-s1-p2 = &sgmii_phy_s1_p2;
+		sgmii-s1-p3 = &sgmii_phy_s1_p3;
+		sgmii-s1-p4 = &sgmii_phy_s1_p4;
+		sgmii-s4-p1 = &sgmii_phy_s4_p1;
 	};
 
 	chosen {
@@ -153,8 +165,9 @@
 	};
 
 	fpga: board-control@2,0 {
-		compatible = "fsl,ls1046aqds-fpga", "fsl,fpga-qixis";
+		compatible = "fsl,ls1046aqds-fpga", "fsl,fpga-qixis", "simple-mfd";
 		reg = <0x2 0x0 0x0000100>;
+		ranges = <0 2 0 0x100>;
 	};
 };
 
@@ -169,7 +182,7 @@
 		compatible = "spansion,m25p80";
 		#address-cells = <1>;
 		#size-cells = <1>;
-		spi-max-frequency = <20000000>;
+		spi-max-frequency = <50000000>;
 		spi-rx-bus-width = <4>;
 		spi-tx-bus-width = <4>;
 		reg = <0>;
@@ -177,3 +190,141 @@
 };
 
 #include "fsl-ls1046-post.dtsi"
+
+&fman0 {
+	ethernet@e0000 {
+		phy-handle = <&qsgmii_phy_s2_p1>;
+		phy-connection-type = "sgmii";
+	};
+
+	ethernet@e2000 {
+		phy-handle = <&sgmii_phy_s4_p1>;
+		phy-connection-type = "sgmii";
+	};
+
+	ethernet@e4000 {
+		phy-handle = <&rgmii_phy1>;
+		phy-connection-type = "rgmii";
+	};
+
+	ethernet@e6000 {
+		phy-handle = <&rgmii_phy2>;
+		phy-connection-type = "rgmii";
+	};
+
+	ethernet@e8000 {
+		phy-handle = <&sgmii_phy_s1_p3>;
+		phy-connection-type = "sgmii";
+	};
+
+	ethernet@ea000 {
+		phy-handle = <&sgmii_phy_s1_p4>;
+		phy-connection-type = "sgmii";
+	};
+
+	ethernet@f0000 { /* DTSEC9/10GEC1 */
+		phy-handle = <&sgmii_phy_s1_p1>;
+		phy-connection-type = "xgmii";
+	};
+
+	ethernet@f2000 { /* DTSEC10/10GEC2 */
+		phy-handle = <&sgmii_phy_s1_p2>;
+		phy-connection-type = "xgmii";
+	};
+};
+
+&fpga {
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	mdio-mux-emi1 {
+		compatible = "mdio-mux-mmioreg", "mdio-mux";
+		mdio-parent-bus = <&mdio0>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x54 1>;    /* BRDCFG4 */
+		mux-mask = <0xe0>; /* EMI1 */
+
+		/* On-board RGMII1 PHY */
+		ls1046mdio0: mdio@0 {
+			reg = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			rgmii_phy1: ethernet-phy@1 { /* MAC3 */
+				reg = <0x1>;
+			};
+		};
+
+		/* On-board RGMII2 PHY */
+		ls1046mdio1: mdio@1 {
+			reg = <0x20>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			rgmii_phy2: ethernet-phy@2 { /* MAC4 */
+				reg = <0x2>;
+			};
+		};
+
+		/* Slot 1 */
+		ls1046mdio_s1: mdio@2 {
+			reg = <0x40>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			sgmii_phy_s1_p1: ethernet-phy@1c {
+				reg = <0x1c>;
+			};
+
+			sgmii_phy_s1_p2: ethernet-phy@1d {
+				reg = <0x1d>;
+			};
+
+			sgmii_phy_s1_p3: ethernet-phy@1e {
+				reg = <0x1e>;
+			};
+
+			sgmii_phy_s1_p4: ethernet-phy@1f {
+				reg = <0x1f>;
+			};
+		};
+
+		/* Slot 2 */
+		ls1046mdio_s2: mdio@3 {
+			reg = <0x60>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			qsgmii_phy_s2_p1: ethernet-phy@8 {
+				reg = <0x8>;
+			};
+
+			qsgmii_phy_s2_p2: ethernet-phy@9 {
+				reg = <0x9>;
+			};
+
+			qsgmii_phy_s2_p3: ethernet-phy@a {
+				reg = <0xa>;
+			};
+
+			qsgmii_phy_s2_p4: ethernet-phy@b {
+				reg = <0xb>;
+			};
+		};
+
+		/* Slot 4 */
+		ls1046mdio_s4: mdio@5 {
+			reg = <0x80>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+
+			sgmii_phy_s4_p1: ethernet-phy@1c {
+				reg = <0x1c>;
+			};
+		};
+	};
+};
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1046a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls1046a.dtsi
index 687fea6d8afa..3d9e29824bb2 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls1046a.dtsi
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1046a.dtsi
@@ -11,6 +11,7 @@
 #include <dt-bindings/clock/fsl,qoriq-clockgen.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/thermal/thermal.h>
+#include <dt-bindings/gpio/gpio.h>
 
 / {
 	compatible = "fsl,ls1046a";
@@ -112,7 +113,7 @@
 	};
 
 	reboot {
-		compatible ="syscon-reboot";
+		compatible = "syscon-reboot";
 		regmap = <&dcfg>;
 		offset = <0xb0>;
 		mask = <0x02>;
@@ -272,6 +273,8 @@
 		#address-cells = <2>;
 		#size-cells = <2>;
 		ranges;
+		dma-ranges = <0x0 0x0 0x0 0x0 0x10000 0x00000000>;
+		dma-coherent;
 
 		ddr: memory-controller@1080000 {
 			compatible = "fsl,qoriq-memory-controller";
@@ -280,8 +283,8 @@
 			big-endian;
 		};
 
-		ifc: ifc@1530000 {
-			compatible = "fsl,ifc", "simple-bus";
+		ifc: memory-controller@1530000 {
+			compatible = "fsl,ifc";
 			reg = <0x0 0x1530000 0x0 0x10000>;
 			interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
 			status = "disabled";
@@ -341,7 +344,7 @@
 					<9 0 &gic GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>,
 					<10 0 &gic GIC_SPI 150 IRQ_TYPE_LEVEL_HIGH>,
 					<11 0 &gic GIC_SPI 151 IRQ_TYPE_LEVEL_HIGH>;
-				interrupt-map-mask = <0xffffffff 0x0>;
+				interrupt-map-mask = <0xf 0x0>;
 			};
 		};
 
@@ -354,13 +357,12 @@
 			ranges = <0x0 0x00 0x1700000 0x100000>;
 			reg = <0x00 0x1700000 0x0 0x100000>;
 			interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
-			dma-coherent;
 
 			sec_jr0: jr@10000 {
 				compatible = "fsl,sec-v5.4-job-ring",
 					     "fsl,sec-v5.0-job-ring",
 					     "fsl,sec-v4.0-job-ring";
-				reg	   = <0x10000 0x10000>;
+				reg = <0x10000 0x10000>;
 				interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
 			};
 
@@ -368,7 +370,7 @@
 				compatible = "fsl,sec-v5.4-job-ring",
 					     "fsl,sec-v5.0-job-ring",
 					     "fsl,sec-v4.0-job-ring";
-				reg	   = <0x20000 0x10000>;
+				reg = <0x20000 0x10000>;
 				interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
 			};
 
@@ -376,7 +378,7 @@
 				compatible = "fsl,sec-v5.4-job-ring",
 					     "fsl,sec-v5.0-job-ring",
 					     "fsl,sec-v4.0-job-ring";
-				reg	   = <0x30000 0x10000>;
+				reg = <0x30000 0x10000>;
 				interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
 			};
 
@@ -384,7 +386,7 @@
 				compatible = "fsl,sec-v5.4-job-ring",
 					     "fsl,sec-v5.0-job-ring",
 					     "fsl,sec-v4.0-job-ring";
-				reg	   = <0x40000 0x10000>;
+				reg = <0x40000 0x10000>;
 				interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
 			};
 		};
@@ -413,6 +415,14 @@
 			ranges = <0x0 0x5 0x08000000 0x8000000>;
 		};
 
+		sfp: efuse@1e80000 {
+			compatible = "fsl,ls1021a-sfp";
+			reg = <0x0 0x1e80000 0x0 0x10000>;
+			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
+					    QORIQ_CLK_PLL_DIV(4)>;
+			clock-names = "sfp";
+		};
+
 		dcfg: dcfg@1ee0000 {
 			compatible = "fsl,ls1046a-dcfg", "syscon";
 			reg = <0x0 0x1ee0000 0x0 0x1000>;
@@ -492,49 +502,52 @@
 		};
 
 		i2c0: i2c@2180000 {
-			compatible = "fsl,vf610-i2c";
+			compatible = "fsl,ls1046a-i2c", "fsl,vf610-i2c";
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <0x0 0x2180000 0x0 0x10000>;
 			interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
 					    QORIQ_CLK_PLL_DIV(2)>;
-			dmas = <&edma0 1 39>,
-			       <&edma0 1 38>;
-			dma-names = "tx", "rx";
+			dmas = <&edma0 1 38>,
+			       <&edma0 1 39>;
+			dma-names = "rx", "tx";
 			status = "disabled";
 		};
 
 		i2c1: i2c@2190000 {
-			compatible = "fsl,vf610-i2c";
+			compatible = "fsl,ls1046a-i2c", "fsl,vf610-i2c";
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <0x0 0x2190000 0x0 0x10000>;
 			interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
 					    QORIQ_CLK_PLL_DIV(2)>;
+			scl-gpios = <&gpio3 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 			status = "disabled";
 		};
 
 		i2c2: i2c@21a0000 {
-			compatible = "fsl,vf610-i2c";
+			compatible = "fsl,ls1046a-i2c", "fsl,vf610-i2c";
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <0x0 0x21a0000 0x0 0x10000>;
 			interrupts = <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
 					    QORIQ_CLK_PLL_DIV(2)>;
+			scl-gpios = <&gpio3 10 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 			status = "disabled";
 		};
 
 		i2c3: i2c@21b0000 {
-			compatible = "fsl,vf610-i2c";
+			compatible = "fsl,ls1046a-i2c", "fsl,vf610-i2c";
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <0x0 0x21b0000 0x0 0x10000>;
 			interrupts = <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
 					    QORIQ_CLK_PLL_DIV(2)>;
+			scl-gpios = <&gpio3 12 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 			status = "disabled";
 		};
 
@@ -683,7 +696,7 @@
 			big-endian;
 		};
 
-		edma0: edma@2c00000 {
+		edma0: dma-controller@2c00000 {
 			#dma-cells = <2>;
 			compatible = "fsl,vf610-edma";
 			reg = <0x0 0x2c00000 0x0 0x10000>,
@@ -701,44 +714,55 @@
 					    QORIQ_CLK_PLL_DIV(2)>;
 		};
 
-		usb0: usb@2f00000 {
-			compatible = "snps,dwc3";
-			reg = <0x0 0x2f00000 0x0 0x10000>;
-			interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
-			dr_mode = "host";
-			snps,quirk-frame-length-adjustment = <0x20>;
-			snps,dis_rxdet_inp3_quirk;
-			snps,incr-burst-type-adjustment = <1>, <4>, <8>, <16>;
-		};
-
-		usb1: usb@3000000 {
-			compatible = "snps,dwc3";
-			reg = <0x0 0x3000000 0x0 0x10000>;
-			interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
-			dr_mode = "host";
-			snps,quirk-frame-length-adjustment = <0x20>;
-			snps,dis_rxdet_inp3_quirk;
-			snps,incr-burst-type-adjustment = <1>, <4>, <8>, <16>;
-		};
-
-		usb2: usb@3100000 {
-			compatible = "snps,dwc3";
-			reg = <0x0 0x3100000 0x0 0x10000>;
-			interrupts = <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>;
-			dr_mode = "host";
-			snps,quirk-frame-length-adjustment = <0x20>;
-			snps,dis_rxdet_inp3_quirk;
-			snps,incr-burst-type-adjustment = <1>, <4>, <8>, <16>;
-		};
-
-		sata: sata@3200000 {
-			compatible = "fsl,ls1046a-ahci";
-			reg = <0x0 0x3200000 0x0 0x10000>,
-				<0x0 0x20140520 0x0 0x4>;
-			reg-names = "ahci", "sata-ecc";
-			interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
-					    QORIQ_CLK_PLL_DIV(2)>;
+		aux_bus: aux_bus {
+			#address-cells = <2>;
+			#size-cells = <2>;
+			compatible = "simple-bus";
+			ranges;
+			dma-ranges = <0x0 0x0 0x0 0x0 0x100 0x00000000>;
+
+			usb0: usb@2f00000 {
+				compatible = "snps,dwc3";
+				reg = <0x0 0x2f00000 0x0 0x10000>;
+				interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
+				dr_mode = "host";
+				snps,quirk-frame-length-adjustment = <0x20>;
+				snps,dis_rxdet_inp3_quirk;
+				snps,incr-burst-type-adjustment = <1>, <4>, <8>, <16>;
+				usb3-lpm-capable;
+			};
+
+			usb1: usb@3000000 {
+				compatible = "snps,dwc3";
+				reg = <0x0 0x3000000 0x0 0x10000>;
+				interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
+				dr_mode = "host";
+				snps,quirk-frame-length-adjustment = <0x20>;
+				snps,dis_rxdet_inp3_quirk;
+				snps,incr-burst-type-adjustment = <1>, <4>, <8>, <16>;
+				usb3-lpm-capable;
+			};
+
+			usb2: usb@3100000 {
+				compatible = "snps,dwc3";
+				reg = <0x0 0x3100000 0x0 0x10000>;
+				interrupts = <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>;
+				dr_mode = "host";
+				snps,quirk-frame-length-adjustment = <0x20>;
+				snps,dis_rxdet_inp3_quirk;
+				snps,incr-burst-type-adjustment = <1>, <4>, <8>, <16>;
+				usb3-lpm-capable;
+			};
+
+			sata: sata@3200000 {
+				compatible = "fsl,ls1046a-ahci";
+				reg = <0x0 0x3200000 0x0 0x10000>,
+					<0x0 0x20140520 0x0 0x4>;
+				reg-names = "ahci", "sata-ecc";
+				interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
+						    QORIQ_CLK_PLL_DIV(2)>;
+			};
 		};
 
 		msi1: msi-controller@1580000 {
@@ -782,7 +806,6 @@
 			#address-cells = <3>;
 			#size-cells = <2>;
 			device_type = "pci";
-			dma-coherent;
 			num-viewport = <8>;
 			bus-range = <0x0 0xff>;
 			ranges = <0x81000000 0x0 0x00000000 0x40 0x00010000 0x0 0x00010000   /* downstream I/O */
@@ -794,6 +817,7 @@
 					<0000 0 0 2 &gic GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>,
 					<0000 0 0 3 &gic GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>,
 					<0000 0 0 4 &gic GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
+			big-endian;
 			status = "disabled";
 		};
 
@@ -802,8 +826,11 @@
 			reg = <0x00 0x03400000 0x0 0x00100000>,
 			      <0x40 0x00000000 0x8 0x00000000>;
 			reg-names = "regs", "addr_space";
+			interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "pme";
 			num-ib-windows = <6>;
 			num-ob-windows = <8>;
+			big-endian;
 			status = "disabled";
 		};
 
@@ -818,7 +845,6 @@
 			#address-cells = <3>;
 			#size-cells = <2>;
 			device_type = "pci";
-			dma-coherent;
 			num-viewport = <8>;
 			bus-range = <0x0 0xff>;
 			ranges = <0x81000000 0x0 0x00000000 0x48 0x00010000 0x0 0x00010000   /* downstream I/O */
@@ -830,6 +856,7 @@
 					<0000 0 0 2 &gic GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>,
 					<0000 0 0 3 &gic GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>,
 					<0000 0 0 4 &gic GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
+			big-endian;
 			status = "disabled";
 		};
 
@@ -838,8 +865,11 @@
 			reg = <0x00 0x03500000 0x0 0x00100000>,
 			      <0x48 0x00000000 0x8 0x00000000>;
 			reg-names = "regs", "addr_space";
+			interrupts = <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "pme";
 			num-ib-windows = <6>;
 			num-ob-windows = <8>;
+			big-endian;
 			status = "disabled";
 		};
 
@@ -854,7 +884,6 @@
 			#address-cells = <3>;
 			#size-cells = <2>;
 			device_type = "pci";
-			dma-coherent;
 			num-viewport = <8>;
 			bus-range = <0x0 0xff>;
 			ranges = <0x81000000 0x0 0x00000000 0x50 0x00010000 0x0 0x00010000   /* downstream I/O */
@@ -866,6 +895,7 @@
 					<0000 0 0 2 &gic GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>,
 					<0000 0 0 3 &gic GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>,
 					<0000 0 0 4 &gic GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>;
+			big-endian;
 			status = "disabled";
 		};
 
@@ -874,8 +904,11 @@
 			reg = <0x00 0x03600000 0x0 0x00100000>,
 			      <0x50 0x00000000 0x8 0x00000000>;
 			reg-names = "regs", "addr_space";
+			interrupts = <GIC_SPI 161 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "pme";
 			num-ib-windows = <6>;
 			num-ob-windows = <8>;
+			big-endian;
 			status = "disabled";
 		};
 
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1088a-ten64.dts b/arch/arm64/boot/dts/freescale/fsl-ls1088a-ten64.dts
index 3063851c2fb9..ef6c8967533e 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls1088a-ten64.dts
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1088a-ten64.dts
@@ -35,18 +35,16 @@
 		 * external power off (e.g ATX Power Button)
 		 * asserted
 		 */
-		powerdn {
+		button-powerdn {
 			label = "External Power Down";
 			gpios = <&gpio1 17 GPIO_ACTIVE_LOW>;
-			interrupts = <&gpio1 17 IRQ_TYPE_EDGE_FALLING>;
 			linux,code = <KEY_POWER>;
 		};
 
 		/* Rear Panel 'ADMIN' button (GPIO_H) */
-		admin {
+		button-admin {
 			label = "ADMIN button";
 			gpios = <&gpio3 8 GPIO_ACTIVE_HIGH>;
-			interrupts = <&gpio3 8 IRQ_TYPE_EDGE_RISING>;
 			linux,code = <KEY_WPS_BUTTON>;
 		};
 	};
@@ -54,17 +52,17 @@
 	leds {
 		compatible = "gpio-leds";
 
-		sfp1down {
+		led-0 {
 			label = "ten64:green:sfp1:down";
 			gpios = <&gpio3 11 GPIO_ACTIVE_HIGH>;
 		};
 
-		sfp2up {
+		led-1 {
 			label = "ten64:green:sfp2:up";
 			gpios = <&gpio3 12 GPIO_ACTIVE_HIGH>;
 		};
 
-		admin {
+		led-2 {
 			label = "ten64:admin";
 			gpios = <&sfpgpio 12 GPIO_ACTIVE_HIGH>;
 		};
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi
index f891ef6a3754..260d045dbd9a 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1088a.dtsi
@@ -206,6 +206,13 @@
 		clock-output-names = "sysclk";
 	};
 
+	reboot {
+		compatible = "syscon-reboot";
+		regmap = <&reset>;
+		offset = <0x0>;
+		mask = <0x02>;
+	};
+
 	soc {
 		compatible = "simple-bus";
 		#address-cells = <2>;
@@ -226,6 +233,11 @@
 			little-endian;
 		};
 
+		reset: syscon@1e60000 {
+			compatible = "fsl,ls1088a-reset", "syscon";
+			reg = <0x0 0x1e60000 0x0 0x10000>;
+		};
+
 		isc: syscon@1f70000 {
 			compatible = "fsl,ls1088a-isc", "syscon";
 			reg = <0x0 0x1f70000 0x0 0x10000>;
@@ -241,22 +253,30 @@
 				interrupt-controller;
 				reg = <0x14 4>;
 				interrupt-map =
-					<0 0 &gic 0 0 GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
-					<1 0 &gic 0 0 GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>,
-					<2 0 &gic 0 0 GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>,
-					<3 0 &gic 0 0 GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
-					<4 0 &gic 0 0 GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
-					<5 0 &gic 0 0 GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>,
-					<6 0 &gic 0 0 GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>,
-					<7 0 &gic 0 0 GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,
-					<8 0 &gic 0 0 GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
-					<9 0 &gic 0 0 GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
-					<10 0 &gic 0 0 GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,
-					<11 0 &gic 0 0 GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
-				interrupt-map-mask = <0xffffffff 0x0>;
+					<0 0 &gic GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
+					<1 0 &gic GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>,
+					<2 0 &gic GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>,
+					<3 0 &gic GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
+					<4 0 &gic GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
+					<5 0 &gic GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>,
+					<6 0 &gic GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>,
+					<7 0 &gic GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,
+					<8 0 &gic GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+					<9 0 &gic GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
+					<10 0 &gic GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,
+					<11 0 &gic GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-map-mask = <0xf 0x0>;
 			};
 		};
 
+		sfp: efuse@1e80000 {
+			compatible = "fsl,ls1028a-sfp";
+			reg = <0x0 0x1e80000 0x0 0x10000>;
+			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
+					    QORIQ_CLK_PLL_DIV(4)>;
+			clock-names = "sfp";
+		};
+
 		tmu: tmu@1f80000 {
 			compatible = "fsl,qoriq-tmu";
 			reg = <0x0 0x1f80000 0x0 0x10000>;
@@ -384,8 +404,8 @@
 			#interrupt-cells = <2>;
 		};
 
-		ifc: ifc@2240000 {
-			compatible = "fsl,ifc", "simple-bus";
+		ifc: memory-controller@2240000 {
+			compatible = "fsl,ifc";
 			reg = <0x0 0x2240000 0x0 0x20000>;
 			interrupts = <0 21 IRQ_TYPE_LEVEL_HIGH>;
 			little-endian;
@@ -485,6 +505,7 @@
 			dr_mode = "host";
 			snps,quirk-frame-length-adjustment = <0x20>;
 			snps,dis_rxdet_inp3_quirk;
+			snps,incr-burst-type-adjustment = <1>, <4>, <8>, <16>;
 			status = "disabled";
 		};
 
@@ -513,28 +534,28 @@
 			sec_jr0: jr@10000 {
 				compatible = "fsl,sec-v5.0-job-ring",
 					     "fsl,sec-v4.0-job-ring";
-				reg	   = <0x10000 0x10000>;
+				reg = <0x10000 0x10000>;
 				interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
 			};
 
 			sec_jr1: jr@20000 {
 				compatible = "fsl,sec-v5.0-job-ring",
 					     "fsl,sec-v4.0-job-ring";
-				reg	   = <0x20000 0x10000>;
+				reg = <0x20000 0x10000>;
 				interrupts = <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>;
 			};
 
 			sec_jr2: jr@30000 {
 				compatible = "fsl,sec-v5.0-job-ring",
 					     "fsl,sec-v4.0-job-ring";
-				reg	   = <0x30000 0x10000>;
+				reg = <0x30000 0x10000>;
 				interrupts = <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>;
 			};
 
 			sec_jr3: jr@40000 {
 				compatible = "fsl,sec-v5.0-job-ring",
 					     "fsl,sec-v4.0-job-ring";
-				reg	   = <0x40000 0x10000>;
+				reg = <0x40000 0x10000>;
 				interrupts = <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>;
 			};
 		};
@@ -758,6 +779,9 @@
 			little-endian;
 			#address-cells = <1>;
 			#size-cells = <0>;
+			clock-frequency = <2500000>;
+			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
+					    QORIQ_CLK_PLL_DIV(1)>;
 			status = "disabled";
 		};
 
@@ -767,6 +791,9 @@
 			little-endian;
 			#address-cells = <1>;
 			#size-cells = <0>;
+			clock-frequency = <2500000>;
+			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
+					    QORIQ_CLK_PLL_DIV(1)>;
 			status = "disabled";
 		};
 
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls2080a-rdb.dts b/arch/arm64/boot/dts/freescale/fsl-ls2080a-rdb.dts
index 44894356059c..8b6915136997 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls2080a-rdb.dts
+++ b/arch/arm64/boot/dts/freescale/fsl-ls2080a-rdb.dts
@@ -14,6 +14,7 @@
 
 #include "fsl-ls2080a.dtsi"
 #include "fsl-ls208xa-rdb.dtsi"
+#include <dt-bindings/interrupt-controller/arm-gic.h>
 
 / {
 	model = "Freescale Layerscape 2080a RDB Board";
@@ -23,3 +24,71 @@
 		stdout-path = "serial1:115200n8";
 	};
 };
+
+&dpmac5 {
+	phy-handle = <&mdio2_phy1>;
+	phy-connection-type = "10gbase-r";
+};
+
+&dpmac6 {
+	phy-handle = <&mdio2_phy2>;
+	phy-connection-type = "10gbase-r";
+};
+
+&dpmac7 {
+	phy-handle = <&mdio2_phy3>;
+	phy-connection-type = "10gbase-r";
+};
+
+&dpmac8 {
+	phy-handle = <&mdio2_phy4>;
+	phy-connection-type = "10gbase-r";
+};
+
+&emdio1 {
+	status = "disabled";
+
+	/* CS4340 PHYs */
+	mdio1_phy1: emdio1-phy@10 {
+		reg = <0x10>;
+	};
+
+	mdio1_phy2: emdio1-phy@11 {
+		reg = <0x11>;
+	};
+
+	mdio1_phy3: emdio1-phy@12 {
+		reg = <0x12>;
+	};
+
+	mdio1_phy4: emdio1-phy@13 {
+		reg = <0x13>;
+	};
+};
+
+&emdio2 {
+	/* AQR405 PHYs */
+	mdio2_phy1: emdio2-phy@0 {
+		compatible = "ethernet-phy-ieee802.3-c45";
+		interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
+		reg = <0x0>;
+	};
+
+	mdio2_phy2: emdio2-phy@1 {
+		compatible = "ethernet-phy-ieee802.3-c45";
+		interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
+		reg = <0x1>;
+	};
+
+	mdio2_phy3: emdio2-phy@2 {
+		compatible = "ethernet-phy-ieee802.3-c45";
+		interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
+		reg = <0x2>;
+	};
+
+	mdio2_phy4: emdio2-phy@3 {
+		compatible = "ethernet-phy-ieee802.3-c45";
+		interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
+		reg = <0x3>;
+	};
+};
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls2080a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls2080a.dtsi
index 6f6667b70028..a2cadf757148 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls2080a.dtsi
+++ b/arch/arm64/boot/dts/freescale/fsl-ls2080a.dtsi
@@ -150,3 +150,7 @@
 	ranges = <0x81000000 0x0 0x00000000 0x16 0x00010000 0x0 0x00010000   /* downstream I/O */
 		  0x82000000 0x0 0x40000000 0x16 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */
 };
+
+&timer {
+	fsl,erratum-a008585;
+};
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls2081a-rdb.dts b/arch/arm64/boot/dts/freescale/fsl-ls2081a-rdb.dts
new file mode 100644
index 000000000000..4461e16fd53a
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/fsl-ls2081a-rdb.dts
@@ -0,0 +1,132 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device Tree file for NXP LS2081A RDB Board.
+ *
+ * Copyright 2017 NXP
+ *
+ * Priyanka Jain <priyanka.jain@nxp.com>
+ *
+ */
+
+/dts-v1/;
+
+#include "fsl-ls2088a.dtsi"
+
+/ {
+	model = "NXP Layerscape 2081A RDB Board";
+	compatible = "fsl,ls2081a-rdb", "fsl,ls2081a";
+
+	aliases {
+		serial0 = &serial0;
+		serial1 = &serial1;
+	};
+
+	chosen {
+		stdout-path = "serial1:115200n8";
+	};
+};
+
+&dspi {
+	status = "okay";
+
+	n25q512a: flash@0 {
+		compatible = "jedec,spi-nor";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		spi-max-frequency = <3000000>;
+		reg = <0>;
+	};
+};
+
+&esdhc {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	pca9547: mux@75 {
+		compatible = "nxp,pca9547";
+		reg = <0x75>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x1>;
+
+			rtc@51 {
+				compatible = "nxp,pcf2129";
+				reg = <0x51>;
+			};
+		};
+
+		i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x2>;
+
+			ina220@40 {
+				compatible = "ti,ina220";
+				reg = <0x40>;
+				shunt-resistor = <500>;
+			};
+		};
+
+		i2c@3 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x3>;
+
+			adt7481@4c {
+				compatible = "adi,adt7461";
+				reg = <0x4c>;
+			};
+		};
+	};
+};
+
+&ifc {
+	status = "disabled";
+};
+
+&qspi {
+	status = "okay";
+
+	s25fs512s0: flash@0 {
+		compatible = "jedec,spi-nor";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		spi-rx-bus-width = <4>;
+		spi-tx-bus-width = <4>;
+		spi-max-frequency = <20000000>;
+		reg = <0>;
+	};
+
+	s25fs512s1: flash@1 {
+		compatible = "jedec,spi-nor";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		spi-rx-bus-width = <4>;
+		spi-tx-bus-width = <4>;
+		spi-max-frequency = <20000000>;
+		reg = <1>;
+	};
+};
+
+&sata0 {
+	status = "okay";
+};
+
+&sata1 {
+	status = "okay";
+};
+
+&usb0 {
+	status = "okay";
+};
+
+&usb1 {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls208xa-qds.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls208xa-qds.dtsi
index 10d2fe091965..f598669e742f 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls208xa-qds.dtsi
+++ b/arch/arm64/boot/dts/freescale/fsl-ls208xa-qds.dtsi
@@ -9,6 +9,27 @@
  *
  */
 
+/* Update DPMAC connections to external PHYs, under SerDes 0x2a_0x49. */
+&dpmac9 {
+	phy-handle = <&mdio0_phy12>;
+	phy-connection-type = "sgmii";
+};
+
+&dpmac10 {
+	phy-handle = <&mdio0_phy13>;
+	phy-connection-type = "sgmii";
+};
+
+&dpmac11 {
+	phy-handle = <&mdio0_phy14>;
+	phy-connection-type = "sgmii";
+};
+
+&dpmac12 {
+	phy-handle = <&mdio0_phy15>;
+	phy-connection-type = "sgmii";
+};
+
 &esdhc {
 	mmc-hs200-1_8v;
 	status = "okay";
@@ -36,9 +57,47 @@
 	     reg = <0x2 0x0 0x10000>;
 	};
 
-	cpld@3,0 {
-	     reg = <0x3 0x0 0x10000>;
-	     compatible = "fsl,ls2080aqds-fpga", "fsl,fpga-qixis";
+	boardctrl: board-control@3,0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "fsl,ls208xaqds-fpga", "fsl,fpga-qixis", "simple-mfd";
+		reg = <3 0 0x1000>;
+		ranges = <0 3 0 0x1000>;
+
+		mdio-mux-emi1@54 {
+			compatible = "mdio-mux-mmioreg", "mdio-mux";
+			mdio-parent-bus = <&emdio1>;
+			reg = <0x54 1>;		/* BRDCFG4 */
+			mux-mask = <0xe0>;	/* EMI1_MDIO */
+			#address-cells=<1>;
+			#size-cells = <0>;
+
+			/* Child MDIO buses, one for each riser card:
+			 * reg = 0x0, 0x20, 0x40, 0x60, 0x80, 0xa0.
+			 * VSC8234 PHYs on the riser cards.
+			 */
+			mdio_mux3: mdio@60 {
+				reg = <0x60>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				mdio0_phy12: mdio-phy0@1c {
+					reg = <0x1c>;
+				};
+
+				mdio0_phy13: mdio-phy1@1d {
+					reg = <0x1d>;
+				};
+
+				mdio0_phy14: mdio-phy2@1e {
+					reg = <0x1e>;
+				};
+
+				mdio0_phy15: mdio-phy3@1f {
+					reg = <0x1f>;
+				};
+			};
+		};
 	};
 };
 
@@ -104,21 +163,21 @@
 
 &dspi {
 	status = "okay";
-	dflash0: n25q128a@0 {
+	dflash0: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "st,m25p80";
 		spi-max-frequency = <3000000>;
 		reg = <0>;
 	};
-	dflash1: sst25wf040b@1 {
+	dflash1: flash@1 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "st,m25p80";
 		spi-max-frequency = <3000000>;
 		reg = <1>;
 	};
-	dflash2: en25s64@2 {
+	dflash2: flash@2 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "st,m25p80";
@@ -129,7 +188,7 @@
 
 &qspi {
 	status = "okay";
-	flash0: s25fl256s1@0 {
+	flash0: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "st,m25p80";
@@ -138,7 +197,7 @@
 		spi-tx-bus-width = <4>;
 		reg = <0>;
 	};
-	flash2: s25fl256s1@2 {
+	flash2: flash@2 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "st,m25p80";
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls208xa-rdb.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls208xa-rdb.dtsi
index 4b71c4fcb35f..3d9647b3da14 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls208xa-rdb.dtsi
+++ b/arch/arm64/boot/dts/freescale/fsl-ls208xa-rdb.dtsi
@@ -49,6 +49,8 @@
 		reg = <0x75>;
 		#address-cells = <1>;
 		#size-cells = <0>;
+		idle-state = <0>;
+
 		i2c@1 {
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -100,7 +102,7 @@
 
 &dspi {
 	status = "okay";
-	dflash0: n25q512a@0 {
+	dflash0: flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "st,m25p80";
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi
index 3cb9c21d2775..348d9e3a9125 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi
+++ b/arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi
@@ -73,7 +73,7 @@
 	};
 
 	reboot {
-		compatible ="syscon-reboot";
+		compatible = "syscon-reboot";
 		regmap = <&rstcr>;
 		offset = <0x0>;
 		mask = <0x2>;
@@ -239,13 +239,12 @@
 		};
 	};
 
-	timer {
+	timer: timer {
 		compatible = "arm,armv8-timer";
 		interrupts = <1 13 4>, /* Physical Secure PPI, active-low */
 			     <1 14 4>, /* Physical Non-Secure PPI, active-low */
 			     <1 11 4>, /* Virtual PPI, active-low */
 			     <1 10 4>; /* Hypervisor PPI, active-low */
-		fsl,erratum-a008585;
 	};
 
 	pmu {
@@ -278,6 +277,14 @@
 			little-endian;
 		};
 
+		sfp: efuse@1e80000 {
+			compatible = "fsl,ls1028a-sfp";
+			reg = <0x0 0x1e80000 0x0 0x10000>;
+			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
+					    QORIQ_CLK_PLL_DIV(4)>;
+			clock-names = "sfp";
+		};
+
 		isc: syscon@1f70000 {
 			compatible = "fsl,ls2080a-isc", "syscon";
 			reg = <0x0 0x1f70000 0x0 0x10000>;
@@ -293,19 +300,19 @@
 				interrupt-controller;
 				reg = <0x14 4>;
 				interrupt-map =
-					<0 0 &gic 0 0 GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
-					<1 0 &gic 0 0 GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>,
-					<2 0 &gic 0 0 GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>,
-					<3 0 &gic 0 0 GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
-					<4 0 &gic 0 0 GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
-					<5 0 &gic 0 0 GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>,
-					<6 0 &gic 0 0 GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>,
-					<7 0 &gic 0 0 GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,
-					<8 0 &gic 0 0 GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
-					<9 0 &gic 0 0 GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
-					<10 0 &gic 0 0 GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,
-					<11 0 &gic 0 0 GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
-				interrupt-map-mask = <0xffffffff 0x0>;
+					<0 0 &gic GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
+					<1 0 &gic GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>,
+					<2 0 &gic GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>,
+					<3 0 &gic GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
+					<4 0 &gic GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
+					<5 0 &gic GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>,
+					<6 0 &gic GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>,
+					<7 0 &gic GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,
+					<8 0 &gic GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+					<9 0 &gic GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
+					<10 0 &gic GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,
+					<11 0 &gic GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-map-mask = <0xf 0x0>;
 			};
 		};
 
@@ -479,28 +486,28 @@
 			sec_jr0: jr@10000 {
 				compatible = "fsl,sec-v5.0-job-ring",
 					     "fsl,sec-v4.0-job-ring";
-				reg	   = <0x10000 0x10000>;
+				reg = <0x10000 0x10000>;
 				interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
 			};
 
 			sec_jr1: jr@20000 {
 				compatible = "fsl,sec-v5.0-job-ring",
 					     "fsl,sec-v4.0-job-ring";
-				reg	   = <0x20000 0x10000>;
+				reg = <0x20000 0x10000>;
 				interrupts = <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>;
 			};
 
 			sec_jr2: jr@30000 {
 				compatible = "fsl,sec-v5.0-job-ring",
 					     "fsl,sec-v4.0-job-ring";
-				reg	   = <0x30000 0x10000>;
+				reg = <0x30000 0x10000>;
 				interrupts = <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>;
 			};
 
 			sec_jr3: jr@40000 {
 				compatible = "fsl,sec-v5.0-job-ring",
 					     "fsl,sec-v4.0-job-ring";
-				reg	   = <0x40000 0x10000>;
+				reg = <0x40000 0x10000>;
 				interrupts = <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>;
 			};
 		};
@@ -525,6 +532,9 @@
 			little-endian;
 			#address-cells = <1>;
 			#size-cells = <0>;
+			clock-frequency = <2500000>;
+			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
+					    QORIQ_CLK_PLL_DIV(2)>;
 			status = "disabled";
 		};
 
@@ -534,6 +544,9 @@
 			little-endian;
 			#address-cells = <1>;
 			#size-cells = <0>;
+			clock-frequency = <2500000>;
+			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
+					    QORIQ_CLK_PLL_DIV(2)>;
 			status = "disabled";
 		};
 
@@ -1036,8 +1049,8 @@
 					    QORIQ_CLK_PLL_DIV(4)>;
 		};
 
-		ifc: ifc@2240000 {
-			compatible = "fsl,ifc", "simple-bus";
+		ifc: memory-controller@2240000 {
+			compatible = "fsl,ifc";
 			reg = <0x0 0x2240000 0x0 0x20000>;
 			interrupts = <0 21 0x4>; /* Level high type */
 			little-endian;
diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3.dts b/arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3.dts
index b21be03da0af..042c486bdda2 100644
--- a/arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3.dts
+++ b/arch/arm64/boot/dts/freescale/fsl-lx2160a-bluebox3.dts
@@ -386,6 +386,8 @@
 				reg = <2>;
 				ethernet = <&dpmac17>;
 				phy-mode = "rgmii-id";
+				rx-internal-delay-ps = <2000>;
+				tx-internal-delay-ps = <2000>;
 
 				fixed-link {
 					speed = <1000>;
@@ -529,6 +531,8 @@
 				reg = <2>;
 				ethernet = <&dpmac18>;
 				phy-mode = "rgmii-id";
+				rx-internal-delay-ps = <2000>;
+				tx-internal-delay-ps = <2000>;
 
 				fixed-link {
 					speed = <1000>;
diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2160a-clearfog-itx.dtsi b/arch/arm64/boot/dts/freescale/fsl-lx2160a-clearfog-itx.dtsi
index 17f8e733972a..a7dcbecc1f41 100644
--- a/arch/arm64/boot/dts/freescale/fsl-lx2160a-clearfog-itx.dtsi
+++ b/arch/arm64/boot/dts/freescale/fsl-lx2160a-clearfog-itx.dtsi
@@ -34,28 +34,28 @@
 	sfp0: sfp-0 {
 		compatible = "sff,sfp";
 		i2c-bus = <&sfp0_i2c>;
-		mod-def0-gpio = <&gpio2 0 GPIO_ACTIVE_LOW>;
+		mod-def0-gpios = <&gpio2 0 GPIO_ACTIVE_LOW>;
 		maximum-power-milliwatt = <2000>;
 	};
 
 	sfp1: sfp-1 {
 		compatible = "sff,sfp";
 		i2c-bus = <&sfp1_i2c>;
-		mod-def0-gpio = <&gpio2 9 GPIO_ACTIVE_LOW>;
+		mod-def0-gpios = <&gpio2 9 GPIO_ACTIVE_LOW>;
 		maximum-power-milliwatt = <2000>;
 	};
 
 	sfp2: sfp-2 {
 		compatible = "sff,sfp";
 		i2c-bus = <&sfp2_i2c>;
-		mod-def0-gpio = <&gpio2 10 GPIO_ACTIVE_LOW>;
+		mod-def0-gpios = <&gpio2 10 GPIO_ACTIVE_LOW>;
 		maximum-power-milliwatt = <2000>;
 	};
 
 	sfp3: sfp-3 {
 		compatible = "sff,sfp";
 		i2c-bus = <&sfp3_i2c>;
-		mod-def0-gpio = <&gpio2 11 GPIO_ACTIVE_LOW>;
+		mod-def0-gpios = <&gpio2 11 GPIO_ACTIVE_LOW>;
 		maximum-power-milliwatt = <2000>;
 	};
 };
@@ -63,21 +63,25 @@
 &dpmac7 {
 	sfp = <&sfp0>;
 	managed = "in-band-status";
+	phys = <&serdes_1 3>;
 };
 
 &dpmac8 {
 	sfp = <&sfp1>;
 	managed = "in-band-status";
+	phys = <&serdes_1 2>;
 };
 
 &dpmac9 {
 	sfp = <&sfp2>;
 	managed = "in-band-status";
+	phys = <&serdes_1 1>;
 };
 
 &dpmac10 {
 	sfp = <&sfp3>;
 	managed = "in-band-status";
+	phys = <&serdes_1 0>;
 };
 
 &emdio2 {
diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2160a-qds.dts b/arch/arm64/boot/dts/freescale/fsl-lx2160a-qds.dts
index d858d9c8b583..4d721197d837 100644
--- a/arch/arm64/boot/dts/freescale/fsl-lx2160a-qds.dts
+++ b/arch/arm64/boot/dts/freescale/fsl-lx2160a-qds.dts
@@ -31,6 +31,130 @@
 		regulator-boot-on;
 		regulator-always-on;
 	};
+
+	mdio-mux-1 {
+		compatible = "mdio-mux-multiplexer";
+		mux-controls = <&mux 0>;
+		mdio-parent-bus = <&emdio1>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		mdio@0 { /* On-board PHY #1 RGMI1*/
+			reg = <0x00>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		mdio@8 { /* On-board PHY #2 RGMI2*/
+			reg = <0x8>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		mdio@18 { /* Slot #1 */
+			reg = <0x18>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		mdio@19 { /* Slot #2 */
+			reg = <0x19>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		mdio@1a { /* Slot #3 */
+			reg = <0x1a>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		mdio@1b { /* Slot #4 */
+			reg = <0x1b>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		mdio@1c { /* Slot #5 */
+			reg = <0x1c>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		mdio@1d { /* Slot #6 */
+			reg = <0x1d>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		mdio@1e { /* Slot #7 */
+			reg = <0x1e>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		mdio@1f { /* Slot #8 */
+			reg = <0x1f>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+
+	mdio-mux-2 {
+		compatible = "mdio-mux-multiplexer";
+		mux-controls = <&mux 1>;
+		mdio-parent-bus = <&emdio2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		mdio@0 { /* Slot #1 (secondary EMI) */
+			reg = <0x00>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		mdio@1 { /* Slot #2 (secondary EMI) */
+			reg = <0x01>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		mdio@2 { /* Slot #3 (secondary EMI) */
+			reg = <0x02>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		mdio@3 { /* Slot #4 (secondary EMI) */
+			reg = <0x03>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		mdio@4 { /* Slot #5 (secondary EMI) */
+			reg = <0x04>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		mdio@5 { /* Slot #6 (secondary EMI) */
+			reg = <0x05>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		mdio@6 { /* Slot #7 (secondary EMI) */
+			reg = <0x06>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		mdio@7 { /* Slot #8 (secondary EMI) */
+			reg = <0x07>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
 };
 
 &can0 {
@@ -81,6 +205,14 @@
 	};
 };
 
+&emdio1 {
+	status = "okay";
+};
+
+&emdio2 {
+	status = "okay";
+};
+
 &esdhc0 {
 	status = "okay";
 };
@@ -107,6 +239,19 @@
 &i2c0 {
 	status = "okay";
 
+	fpga@66 {
+		compatible = "fsl,lx2160aqds-fpga", "fsl,fpga-qixis-i2c",
+			     "simple-mfd";
+		reg = <0x66>;
+
+		mux: mux-controller {
+			compatible = "reg-mux";
+			#mux-control-cells = <1>;
+			mux-reg-masks = <0x54 0xf8>, /* 0: reg 0x54, bits 7:3 */
+					<0x54 0x07>; /* 1: reg 0x54, bit 2:0 */
+		};
+	};
+
 	i2c-mux@77 {
 		compatible = "nxp,pca9547";
 		reg = <0x77>;
@@ -156,6 +301,10 @@
 	};
 };
 
+&optee {
+	status = "okay";
+};
+
 &sata0 {
 	status = "okay";
 };
diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2160a-rdb.dts b/arch/arm64/boot/dts/freescale/fsl-lx2160a-rdb.dts
index 028ff8074b9d..0c44b3cbef77 100644
--- a/arch/arm64/boot/dts/freescale/fsl-lx2160a-rdb.dts
+++ b/arch/arm64/boot/dts/freescale/fsl-lx2160a-rdb.dts
@@ -49,6 +49,14 @@
 	managed = "in-band-status";
 };
 
+&dpmac5 {
+	phy-handle = <&inphi_phy>;
+};
+
+&dpmac6 {
+	phy-handle = <&inphi_phy>;
+};
+
 &dpmac17 {
 	phy-handle = <&rgmii_phy1>;
 	phy-connection-type = "rgmii-id";
@@ -109,6 +117,15 @@
 	};
 };
 
+&emdio2 {
+	status = "okay";
+
+	inphi_phy: ethernet-phy@0 {
+		compatible = "ethernet-phy-id0210.7440";
+		reg = <0x0>;
+	};
+};
+
 &esdhc0 {
 	sd-uhs-sdr104;
 	sd-uhs-sdr50;
@@ -202,6 +219,10 @@
 	};
 };
 
+&optee {
+	status = "okay";
+};
+
 &pcs_mdio3 {
 	status = "okay";
 };
diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi b/arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi
index dc8661ebd1f6..8c76d86cb756 100644
--- a/arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi
+++ b/arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi
@@ -612,6 +612,12 @@
 		ranges;
 		dma-ranges = <0x0 0x0 0x0 0x0 0x10000 0x00000000>;
 
+		serdes_1: phy@1ea0000 {
+			compatible = "fsl,lynx-28g";
+			reg = <0x0 0x1ea0000 0x0 0x1e30>;
+			#phy-cells = <1>;
+		};
+
 		crypto: crypto@8000000 {
 			compatible = "fsl,sec-v5.0", "fsl,sec-v4.0";
 			fsl,sec-era = <10>;
@@ -626,28 +632,28 @@
 			sec_jr0: jr@10000 {
 				compatible = "fsl,sec-v5.0-job-ring",
 					     "fsl,sec-v4.0-job-ring";
-				reg        = <0x10000 0x10000>;
+				reg = <0x10000 0x10000>;
 				interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
 			};
 
 			sec_jr1: jr@20000 {
 				compatible = "fsl,sec-v5.0-job-ring",
 					     "fsl,sec-v4.0-job-ring";
-				reg        = <0x20000 0x10000>;
+				reg = <0x20000 0x10000>;
 				interrupts = <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>;
 			};
 
 			sec_jr2: jr@30000 {
 				compatible = "fsl,sec-v5.0-job-ring",
 					     "fsl,sec-v4.0-job-ring";
-				reg        = <0x30000 0x10000>;
+				reg = <0x30000 0x10000>;
 				interrupts = <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>;
 			};
 
 			sec_jr3: jr@40000 {
 				compatible = "fsl,sec-v5.0-job-ring",
 					     "fsl,sec-v4.0-job-ring";
-				reg        = <0x40000 0x10000>;
+				reg = <0x40000 0x10000>;
 				interrupts = <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>;
 			};
 		};
@@ -665,6 +671,14 @@
 			little-endian;
 		};
 
+		sfp: efuse@1e80000 {
+			compatible = "fsl,ls1028a-sfp";
+			reg = <0x0 0x1e80000 0x0 0x10000>;
+			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
+					    QORIQ_CLK_PLL_DIV(4)>;
+			clock-names = "sfp";
+		};
+
 		isc: syscon@1f70000 {
 			compatible = "fsl,lx2160a-isc", "syscon";
 			reg = <0x0 0x1f70000 0x0 0x10000>;
@@ -680,19 +694,19 @@
 				interrupt-controller;
 				reg = <0x14 4>;
 				interrupt-map =
-					<0 0 &gic 0 0 GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
-					<1 0 &gic 0 0 GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>,
-					<2 0 &gic 0 0 GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>,
-					<3 0 &gic 0 0 GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
-					<4 0 &gic 0 0 GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
-					<5 0 &gic 0 0 GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>,
-					<6 0 &gic 0 0 GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>,
-					<7 0 &gic 0 0 GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,
-					<8 0 &gic 0 0 GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
-					<9 0 &gic 0 0 GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
-					<10 0 &gic 0 0 GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,
-					<11 0 &gic 0 0 GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
-				interrupt-map-mask = <0xffffffff 0x0>;
+					<0 0 &gic GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
+					<1 0 &gic GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>,
+					<2 0 &gic GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>,
+					<3 0 &gic GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
+					<4 0 &gic GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
+					<5 0 &gic GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>,
+					<6 0 &gic GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>,
+					<7 0 &gic GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,
+					<8 0 &gic GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+					<9 0 &gic GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
+					<10 0 &gic GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,
+					<11 0 &gic GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-map-mask = <0xf 0x0>;
 			};
 		};
 
@@ -719,7 +733,7 @@
 			clock-names = "i2c";
 			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
 					    QORIQ_CLK_PLL_DIV(16)>;
-			scl-gpio = <&gpio2 15 GPIO_ACTIVE_HIGH>;
+			scl-gpios = <&gpio2 15 GPIO_ACTIVE_HIGH>;
 			status = "disabled";
 		};
 
@@ -768,7 +782,7 @@
 			clock-names = "i2c";
 			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
 					    QORIQ_CLK_PLL_DIV(16)>;
-			scl-gpio = <&gpio2 16 GPIO_ACTIVE_HIGH>;
+			scl-gpios = <&gpio2 16 GPIO_ACTIVE_HIGH>;
 			status = "disabled";
 		};
 
@@ -903,7 +917,7 @@
 					    QORIQ_CLK_PLL_DIV(8)>,
 				 <&clockgen QORIQ_CLK_SYSCLK 0>;
 			clock-names = "ipg", "per";
-			fsl,clk-source = <0>;
+			fsl,clk-source = /bits/ 8 <0>;
 			status = "disabled";
 		};
 
@@ -915,7 +929,7 @@
 					    QORIQ_CLK_PLL_DIV(8)>,
 				 <&clockgen QORIQ_CLK_SYSCLK 0>;
 			clock-names = "ipg", "per";
-			fsl,clk-source = <0>;
+			fsl,clk-source = /bits/ 8 <0>;
 			status = "disabled";
 		};
 
@@ -1023,6 +1037,7 @@
 			interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
 			dr_mode = "host";
 			snps,quirk-frame-length-adjustment = <0x20>;
+			usb3-lpm-capable;
 			snps,dis_rxdet_inp3_quirk;
 			snps,incr-burst-type-adjustment = <1>, <4>, <8>, <16>;
 			status = "disabled";
@@ -1034,6 +1049,7 @@
 			interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>;
 			dr_mode = "host";
 			snps,quirk-frame-length-adjustment = <0x20>;
+			usb3-lpm-capable;
 			snps,dis_rxdet_inp3_quirk;
 			snps,incr-burst-type-adjustment = <1>, <4>, <8>, <16>;
 			status = "disabled";
@@ -1369,6 +1385,9 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 			little-endian;
+			clock-frequency = <2500000>;
+			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
+					    QORIQ_CLK_PLL_DIV(2)>;
 			status = "disabled";
 		};
 
@@ -1379,6 +1398,9 @@
 			little-endian;
 			#address-cells = <1>;
 			#size-cells = <0>;
+			clock-frequency = <2500000>;
+			clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL
+					    QORIQ_CLK_PLL_DIV(2)>;
 			status = "disabled";
 		};
 
@@ -1751,4 +1773,12 @@
 			};
 		};
 	};
+
+	firmware {
+		optee: optee {
+			compatible = "linaro,optee-tz";
+			method = "smc";
+			status = "disabled";
+		};
+	};
 };
diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2162a-qds.dts b/arch/arm64/boot/dts/freescale/fsl-lx2162a-qds.dts
index e1defee1ad27..9f5ff1ffe7d5 100644
--- a/arch/arm64/boot/dts/freescale/fsl-lx2162a-qds.dts
+++ b/arch/arm64/boot/dts/freescale/fsl-lx2162a-qds.dts
@@ -34,7 +34,7 @@
 		compatible = "mdio-mux-multiplexer";
 		mux-controls = <&mux 0>;
 		mdio-parent-bus = <&emdio1>;
-		#address-cells=<1>;
+		#address-cells = <1>;
 		#size-cells = <0>;
 
 		mdio@0 { /* On-board RTL8211F PHY #1 RGMII1 */
@@ -114,7 +114,7 @@
 		compatible = "mdio-mux-multiplexer";
 		mux-controls = <&mux 1>;
 		mdio-parent-bus = <&emdio2>;
-		#address-cells=<1>;
+		#address-cells = <1>;
 		#size-cells = <0>;
 
 		mdio@0 { /* Slot #1 (secondary EMI) */
@@ -167,6 +167,14 @@
 	};
 };
 
+&can0 {
+	status = "okay";
+};
+
+&can1 {
+	status = "okay";
+};
+
 &crypto {
 	status = "okay";
 };
@@ -226,10 +234,17 @@
 };
 
 &esdhc0 {
+	sd-uhs-sdr104;
+	sd-uhs-sdr50;
+	sd-uhs-sdr25;
+	sd-uhs-sdr12;
 	status = "okay";
 };
 
 &esdhc1 {
+	mmc-hs200-1_8v;
+	mmc-hs400-1_8v;
+	bus-width = <8>;
 	status = "okay";
 };
 
@@ -302,11 +317,17 @@
 			rtc@51 {
 				compatible = "nxp,pcf2129";
 				reg = <0x51>;
+				/* IRQ_RTC_B -> IRQ11_B(CPLD) -> IRQ11(CPU), active low */
+				interrupts-extended = <&extirq 11 IRQ_TYPE_LEVEL_LOW>;
 			};
 		};
 	};
 };
 
+&optee {
+	status = "okay";
+};
+
 &sata0 {
 	status = "okay";
 };
diff --git a/arch/arm64/boot/dts/freescale/imx8-ss-conn.dtsi b/arch/arm64/boot/dts/freescale/imx8-ss-conn.dtsi
index a79f42a9618e..10370d1a6c6d 100644
--- a/arch/arm64/boot/dts/freescale/imx8-ss-conn.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8-ss-conn.dtsi
@@ -38,9 +38,9 @@ conn_subsys: bus@5b000000 {
 		interrupts = <GIC_SPI 232 IRQ_TYPE_LEVEL_HIGH>;
 		reg = <0x5b010000 0x10000>;
 		clocks = <&sdhc0_lpcg IMX_LPCG_CLK_4>,
-			 <&sdhc0_lpcg IMX_LPCG_CLK_5>,
-			 <&sdhc0_lpcg IMX_LPCG_CLK_0>;
-		clock-names = "ipg", "per", "ahb";
+			 <&sdhc0_lpcg IMX_LPCG_CLK_0>,
+			 <&sdhc0_lpcg IMX_LPCG_CLK_5>;
+		clock-names = "ipg", "ahb", "per";
 		power-domains = <&pd IMX_SC_R_SDHC_0>;
 		status = "disabled";
 	};
@@ -49,12 +49,12 @@ conn_subsys: bus@5b000000 {
 		interrupts = <GIC_SPI 233 IRQ_TYPE_LEVEL_HIGH>;
 		reg = <0x5b020000 0x10000>;
 		clocks = <&sdhc1_lpcg IMX_LPCG_CLK_4>,
-			 <&sdhc1_lpcg IMX_LPCG_CLK_5>,
-			 <&sdhc1_lpcg IMX_LPCG_CLK_0>;
-		clock-names = "ipg", "per", "ahb";
+			 <&sdhc1_lpcg IMX_LPCG_CLK_0>,
+			 <&sdhc1_lpcg IMX_LPCG_CLK_5>;
+		clock-names = "ipg", "ahb", "per";
 		power-domains = <&pd IMX_SC_R_SDHC_1>;
 		fsl,tuning-start-tap = <20>;
-		fsl,tuning-step= <2>;
+		fsl,tuning-step = <2>;
 		status = "disabled";
 	};
 
@@ -62,9 +62,9 @@ conn_subsys: bus@5b000000 {
 		interrupts = <GIC_SPI 234 IRQ_TYPE_LEVEL_HIGH>;
 		reg = <0x5b030000 0x10000>;
 		clocks = <&sdhc2_lpcg IMX_LPCG_CLK_4>,
-			 <&sdhc2_lpcg IMX_LPCG_CLK_5>,
-			 <&sdhc2_lpcg IMX_LPCG_CLK_0>;
-		clock-names = "ipg", "per", "ahb";
+			 <&sdhc2_lpcg IMX_LPCG_CLK_0>,
+			 <&sdhc2_lpcg IMX_LPCG_CLK_5>;
+		clock-names = "ipg", "ahb", "per";
 		power-domains = <&pd IMX_SC_R_SDHC_2>;
 		status = "disabled";
 	};
@@ -83,8 +83,8 @@ conn_subsys: bus@5b000000 {
 		assigned-clocks = <&clk IMX_SC_R_ENET_0 IMX_SC_PM_CLK_PER>,
 				  <&clk IMX_SC_R_ENET_0 IMX_SC_C_CLKDIV>;
 		assigned-clock-rates = <250000000>, <125000000>;
-		fsl,num-tx-queues=<3>;
-		fsl,num-rx-queues=<3>;
+		fsl,num-tx-queues = <3>;
+		fsl,num-rx-queues = <3>;
 		power-domains = <&pd IMX_SC_R_ENET_0>;
 		status = "disabled";
 	};
@@ -103,8 +103,8 @@ conn_subsys: bus@5b000000 {
 		assigned-clocks = <&clk IMX_SC_R_ENET_1 IMX_SC_PM_CLK_PER>,
 				  <&clk IMX_SC_R_ENET_1 IMX_SC_C_CLKDIV>;
 		assigned-clock-rates = <250000000>, <125000000>;
-		fsl,num-tx-queues=<3>;
-		fsl,num-rx-queues=<3>;
+		fsl,num-tx-queues = <3>;
+		fsl,num-rx-queues = <3>;
 		power-domains = <&pd IMX_SC_R_ENET_1>;
 		status = "disabled";
 	};
diff --git a/arch/arm64/boot/dts/freescale/imx8-ss-ddr.dtsi b/arch/arm64/boot/dts/freescale/imx8-ss-ddr.dtsi
index 8b5cad4e2700..7d5183c6c5be 100644
--- a/arch/arm64/boot/dts/freescale/imx8-ss-ddr.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8-ss-ddr.dtsi
@@ -10,7 +10,7 @@ ddr_subsys: bus@5c000000 {
 	#size-cells = <1>;
 	ranges = <0x5c000000 0x0 0x5c000000 0x1000000>;
 
-	ddr-pmu@5c020000 {
+	ddr_pmu0: ddr-pmu@5c020000 {
 		compatible = "fsl,imx8-ddr-pmu";
 		reg = <0x5c020000 0x10000>;
 		interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>;
diff --git a/arch/arm64/boot/dts/freescale/imx8-ss-dma.dtsi b/arch/arm64/boot/dts/freescale/imx8-ss-dma.dtsi
index 960a802b8b6e..d7b4229bb4a2 100644
--- a/arch/arm64/boot/dts/freescale/imx8-ss-dma.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8-ss-dma.dtsi
@@ -111,8 +111,9 @@ dma_subsys: bus@5a000000 {
 	i2c0: i2c@5a800000 {
 		reg = <0x5a800000 0x4000>;
 		interrupts = <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&i2c0_lpcg IMX_LPCG_CLK_0>;
-		clock-names = "per";
+		clocks = <&i2c0_lpcg IMX_LPCG_CLK_0>,
+			 <&i2c0_lpcg IMX_LPCG_CLK_4>;
+		clock-names = "per", "ipg";
 		assigned-clocks = <&clk IMX_SC_R_I2C_0 IMX_SC_PM_CLK_PER>;
 		assigned-clock-rates = <24000000>;
 		power-domains = <&pd IMX_SC_R_I2C_0>;
@@ -122,8 +123,9 @@ dma_subsys: bus@5a000000 {
 	i2c1: i2c@5a810000 {
 		reg = <0x5a810000 0x4000>;
 		interrupts = <GIC_SPI 221 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&i2c1_lpcg IMX_LPCG_CLK_0>;
-		clock-names = "per";
+		clocks = <&i2c1_lpcg IMX_LPCG_CLK_0>,
+			 <&i2c1_lpcg IMX_LPCG_CLK_4>;
+		clock-names = "per", "ipg";
 		assigned-clocks = <&clk IMX_SC_R_I2C_1 IMX_SC_PM_CLK_PER>;
 		assigned-clock-rates = <24000000>;
 		power-domains = <&pd IMX_SC_R_I2C_1>;
@@ -133,8 +135,9 @@ dma_subsys: bus@5a000000 {
 	i2c2: i2c@5a820000 {
 		reg = <0x5a820000 0x4000>;
 		interrupts = <GIC_SPI 222 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&i2c2_lpcg IMX_LPCG_CLK_0>;
-		clock-names = "per";
+		clocks = <&i2c2_lpcg IMX_LPCG_CLK_0>,
+			 <&i2c2_lpcg IMX_LPCG_CLK_4>;
+		clock-names = "per", "ipg";
 		assigned-clocks = <&clk IMX_SC_R_I2C_2 IMX_SC_PM_CLK_PER>;
 		assigned-clock-rates = <24000000>;
 		power-domains = <&pd IMX_SC_R_I2C_2>;
@@ -144,8 +147,9 @@ dma_subsys: bus@5a000000 {
 	i2c3: i2c@5a830000 {
 		reg = <0x5a830000 0x4000>;
 		interrupts = <GIC_SPI 223 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&i2c3_lpcg IMX_LPCG_CLK_0>;
-		clock-names = "per";
+		clocks = <&i2c3_lpcg IMX_LPCG_CLK_0>,
+			 <&i2c3_lpcg IMX_LPCG_CLK_4>;
+		clock-names = "per", "ipg";
 		assigned-clocks = <&clk IMX_SC_R_I2C_3 IMX_SC_PM_CLK_PER>;
 		assigned-clock-rates = <24000000>;
 		power-domains = <&pd IMX_SC_R_I2C_3>;
diff --git a/arch/arm64/boot/dts/freescale/imx8-ss-lsio.dtsi b/arch/arm64/boot/dts/freescale/imx8-ss-lsio.dtsi
index ee4e585a9c39..6446e6df7a9a 100644
--- a/arch/arm64/boot/dts/freescale/imx8-ss-lsio.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8-ss-lsio.dtsi
@@ -141,6 +141,22 @@ lsio_subsys: bus@5d000000 {
 		status = "disabled";
 	};
 
+	lsio_mu5: mailbox@5d200000 {
+		reg = <0x5d200000 0x10000>;
+		interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>;
+		#mbox-cells = <2>;
+		power-domains = <&pd IMX_SC_R_MU_5A>;
+		status = "disabled";
+	};
+
+	lsio_mu6: mailbox@5d210000 {
+		reg = <0x5d210000 0x10000>;
+		interrupts = <GIC_SPI 185 IRQ_TYPE_LEVEL_HIGH>;
+		#mbox-cells = <2>;
+		power-domains = <&pd IMX_SC_R_MU_6A>;
+		status = "disabled";
+	};
+
 	lsio_mu13: mailbox@5d280000 {
 		reg = <0x5d280000 0x10000>;
 		interrupts = <GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>;
diff --git a/arch/arm64/boot/dts/freescale/imx8-ss-vpu.dtsi b/arch/arm64/boot/dts/freescale/imx8-ss-vpu.dtsi
new file mode 100644
index 000000000000..c6540768bdb9
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8-ss-vpu.dtsi
@@ -0,0 +1,74 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2021 NXP
+ *	Dong Aisheng <aisheng.dong@nxp.com>
+ */
+
+vpu: vpu@2c000000 {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	ranges = <0x2c000000 0x0 0x2c000000 0x2000000>;
+	reg = <0 0x2c000000 0 0x1000000>;
+	power-domains = <&pd IMX_SC_R_VPU>;
+	status = "disabled";
+
+	mu_m0: mailbox@2d000000 {
+		compatible = "fsl,imx6sx-mu";
+		reg = <0x2d000000 0x20000>;
+		interrupts = <GIC_SPI 469 IRQ_TYPE_LEVEL_HIGH>;
+		#mbox-cells = <2>;
+		power-domains = <&pd IMX_SC_R_VPU_MU_0>;
+		status = "disabled";
+	};
+
+	mu1_m0: mailbox@2d020000 {
+		compatible = "fsl,imx6sx-mu";
+		reg = <0x2d020000 0x20000>;
+		interrupts = <GIC_SPI 470 IRQ_TYPE_LEVEL_HIGH>;
+		#mbox-cells = <2>;
+		power-domains = <&pd IMX_SC_R_VPU_MU_1>;
+		status = "disabled";
+	};
+
+	mu2_m0: mailbox@2d040000 {
+		compatible = "fsl,imx6sx-mu";
+		reg = <0x2d040000 0x20000>;
+		interrupts = <GIC_SPI 474 IRQ_TYPE_LEVEL_HIGH>;
+		#mbox-cells = <2>;
+		power-domains = <&pd IMX_SC_R_VPU_MU_2>;
+		status = "disabled";
+	};
+
+	vpu_core0: vpu-core@2d080000 {
+		reg = <0x2d080000 0x10000>;
+		compatible = "nxp,imx8q-vpu-decoder";
+		power-domains = <&pd IMX_SC_R_VPU_DEC_0>;
+		mbox-names = "tx0", "tx1", "rx";
+		mboxes = <&mu_m0 0 0>,
+			<&mu_m0 0 1>,
+			<&mu_m0 1 0>;
+		status = "disabled";
+	};
+
+	vpu_core1: vpu-core@2d090000 {
+		reg = <0x2d090000 0x10000>;
+		compatible = "nxp,imx8q-vpu-encoder";
+		power-domains = <&pd IMX_SC_R_VPU_ENC_0>;
+		mbox-names = "tx0", "tx1", "rx";
+		mboxes = <&mu1_m0 0 0>,
+			<&mu1_m0 0 1>,
+			<&mu1_m0 1 0>;
+		status = "disabled";
+	};
+
+	vpu_core2: vpu-core@2d0a0000 {
+		reg = <0x2d0a0000 0x10000>;
+		compatible = "nxp,imx8q-vpu-encoder";
+		power-domains = <&pd IMX_SC_R_VPU_ENC_1>;
+		mbox-names = "tx0", "tx1", "rx";
+		mboxes = <&mu2_m0 0 0>,
+			<&mu2_m0 0 1>,
+			<&mu2_m0 1 0>;
+		status = "disabled";
+	};
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8dxl-evk.dts b/arch/arm64/boot/dts/freescale/imx8dxl-evk.dts
new file mode 100644
index 000000000000..ca2a43e0cbf6
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8dxl-evk.dts
@@ -0,0 +1,426 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2019~2020, 2022 NXP
+ */
+
+/dts-v1/;
+
+#include "imx8dxl.dtsi"
+
+/ {
+	model = "Freescale i.MX8DXL EVK";
+	compatible = "fsl,imx8dxl-evk", "fsl,imx8dxl";
+
+	aliases {
+		i2c2 = &i2c2;
+		mmc0 = &usdhc1;
+		mmc1 = &usdhc2;
+		serial0 = &lpuart0;
+	};
+
+	chosen {
+		stdout-path = &lpuart0;
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x00000000 0x80000000 0 0x40000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		/*
+		 * Memory reserved for optee usage. Please do not use.
+		 * This will be automatically added to dtb if OP-TEE is installed.
+		 * optee@96000000 {
+		 *     reg = <0 0x96000000 0 0x2000000>;
+		 *     no-map;
+		 * };
+		 */
+
+		/* global autoconfigured region for contiguous allocations */
+		linux,cma {
+			compatible = "shared-dma-pool";
+			reusable;
+			size = <0 0x14000000>;
+			alloc-ranges = <0 0x98000000 0 0x14000000>;
+			linux,cma-default;
+		};
+	};
+
+	mux3_en: regulator-0 {
+		compatible = "regulator-fixed";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-name = "mux3_en";
+		gpio = <&pca6416_2 8 GPIO_ACTIVE_LOW>;
+		regulator-always-on;
+	};
+
+	reg_fec1_sel: regulator-1 {
+		compatible = "regulator-fixed";
+		regulator-name = "fec1_supply";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&pca6416_1 11 GPIO_ACTIVE_LOW>;
+		regulator-always-on;
+		status = "disabled";
+	};
+
+	reg_fec1_io: regulator-2 {
+		compatible = "regulator-fixed";
+		regulator-name = "fec1_io_supply";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		gpio = <&max7322 0 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-always-on;
+		status = "disabled";
+	};
+
+	reg_usdhc2_vmmc: regulator-3 {
+		compatible = "regulator-fixed";
+		regulator-name = "SD1_SPWR";
+		regulator-min-microvolt = <3000000>;
+		regulator-max-microvolt = <3000000>;
+		gpio = <&lsio_gpio4 30 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		off-on-delay-us = <3480>;
+	};
+};
+
+&eqos {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_eqos>;
+	phy-mode = "rgmii-id";
+	phy-handle = <&ethphy0>;
+	nvmem-cells = <&fec_mac1>;
+	nvmem-cell-names = "mac-address";
+	snps,reset-gpios = <&pca6416_1 2 GPIO_ACTIVE_LOW>;
+	snps,reset-delays-us = <10 20 200000>;
+	status = "okay";
+
+	mdio {
+		compatible = "snps,dwmac-mdio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy0: ethernet-phy@0 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <0>;
+			eee-broken-1000t;
+			qca,disable-smarteee;
+			vddio-supply = <&vddio0>;
+
+			vddio0: vddio-regulator {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+		};
+	};
+};
+
+/*
+ * fec1 shares the some PINs with usdhc2.
+ * by default usdhc2 is enabled in this dts.
+ * Please disable usdhc2 to enable fec1
+ */
+&fec1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_fec1>;
+	phy-mode = "rgmii-txid";
+	phy-handle = <&ethphy1>;
+	fsl,magic-packet;
+	rx-internal-delay-ps = <2000>;
+	nvmem-cells = <&fec_mac0>;
+	nvmem-cell-names = "mac-address";
+	status = "disabled";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy1: ethernet-phy@1 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <1>;
+			reset-gpios = <&pca6416_1 0 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <10000>;
+			qca,disable-smarteee;
+			vddio-supply = <&vddio1>;
+
+			vddio1: vddio-regulator {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+		};
+	};
+};
+
+&i2c2 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	status = "okay";
+
+	pca6416_1: gpio@20 {
+		compatible = "ti,tca6416";
+		reg = <0x20>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	pca6416_2: gpio@21 {
+		compatible = "ti,tca6416";
+		reg = <0x21>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	pca9548_1: i2c-mux@70 {
+		compatible = "nxp,pca9548";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0x70>;
+
+		i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x0>;
+
+			max7322: gpio@68 {
+				compatible = "maxim,max7322";
+				reg = <0x68>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				status = "disabled";
+			};
+		};
+
+		i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x4>;
+		};
+
+		i2c@5 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x5>;
+		};
+
+		i2c@6 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x6>;
+		};
+	};
+};
+
+&lpuart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_lpuart0>;
+	status = "okay";
+};
+
+&lsio_gpio4 {
+	status = "okay";
+};
+
+&lsio_gpio5 {
+	status = "okay";
+};
+
+&thermal_zones {
+	pmic-thermal0 {
+		polling-delay-passive = <250>;
+		polling-delay = <2000>;
+		thermal-sensors = <&tsens IMX_SC_R_PMIC_0>;
+
+		trips {
+			pmic_alert0: trip0 {
+				temperature = <110000>;
+				hysteresis = <2000>;
+				type = "passive";
+			};
+
+			pmic_crit0: trip1 {
+				temperature = <125000>;
+				hysteresis = <2000>;
+				type = "critical";
+			};
+		};
+
+		cooling-maps {
+			map0 {
+				trip = <&pmic_alert0>;
+				cooling-device =
+					<&A35_0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+					<&A35_1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+			};
+		};
+	};
+};
+
+&usdhc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	bus-width = <8>;
+	no-sd;
+	no-sdio;
+	non-removable;
+	status = "okay";
+};
+
+&usdhc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
+	bus-width = <4>;
+	vmmc-supply = <&reg_usdhc2_vmmc>;
+	cd-gpios = <&lsio_gpio5 1 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&lsio_gpio5 0 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hog>;
+
+	pinctrl_hog: hoggrp {
+		fsl,pins = <
+			IMX8DXL_COMP_CTL_GPIO_1V8_3V3_GPIORHB_PAD	0x000514a0
+			IMX8DXL_COMP_CTL_GPIO_1V8_3V3_GPIORHK_PAD	0x000014a0
+			IMX8DXL_SPI3_CS0_ADMA_ACM_MCLK_OUT1		0x0600004c
+			IMX8DXL_SNVS_TAMPER_OUT1_LSIO_GPIO2_IO05_IN	0x0600004c
+		>;
+	};
+
+	pinctrl_usbotg1: usbotg1grp {
+		fsl,pins = <
+			IMX8DXL_USB_SS3_TC0_CONN_USB_OTG1_PWR		0x00000021
+		>;
+	};
+
+	pinctrl_usbotg2: usbotg2grp {
+		fsl,pins = <
+			IMX8DXL_USB_SS3_TC1_CONN_USB_OTG2_PWR		0x00000021
+		>;
+	};
+
+	pinctrl_eqos: eqosgrp {
+		fsl,pins = <
+			IMX8DXL_ENET0_MDC_CONN_EQOS_MDC				0x06000020
+			IMX8DXL_ENET0_MDIO_CONN_EQOS_MDIO			0x06000020
+			IMX8DXL_ENET1_RGMII_RXC_CONN_EQOS_RGMII_RXC		0x06000020
+			IMX8DXL_ENET1_RGMII_RXD0_CONN_EQOS_RGMII_RXD0		0x06000020
+			IMX8DXL_ENET1_RGMII_RXD1_CONN_EQOS_RGMII_RXD1		0x06000020
+			IMX8DXL_ENET1_RGMII_RXD2_CONN_EQOS_RGMII_RXD2		0x06000020
+			IMX8DXL_ENET1_RGMII_RXD3_CONN_EQOS_RGMII_RXD3		0x06000020
+			IMX8DXL_ENET1_RGMII_RX_CTL_CONN_EQOS_RGMII_RX_CTL	0x06000020
+			IMX8DXL_ENET1_RGMII_TXC_CONN_EQOS_RGMII_TXC		0x06000020
+			IMX8DXL_ENET1_RGMII_TXD0_CONN_EQOS_RGMII_TXD0		0x06000020
+			IMX8DXL_ENET1_RGMII_TXD1_CONN_EQOS_RGMII_TXD1		0x06000020
+			IMX8DXL_ENET1_RGMII_TXD2_CONN_EQOS_RGMII_TXD2		0x06000020
+			IMX8DXL_ENET1_RGMII_TXD3_CONN_EQOS_RGMII_TXD3		0x06000020
+			IMX8DXL_ENET1_RGMII_TX_CTL_CONN_EQOS_RGMII_TX_CTL	0x06000020
+		>;
+	};
+
+	pinctrl_fec1: fec1grp {
+		fsl,pins = <
+			IMX8DXL_COMP_CTL_GPIO_1V8_3V3_ENET_ENETB0_PAD		0x000014a0
+			IMX8DXL_COMP_CTL_GPIO_1V8_3V3_ENET_ENETB1_PAD		0x000014a0
+			IMX8DXL_ENET0_MDC_CONN_ENET0_MDC			0x06000020
+			IMX8DXL_ENET0_MDIO_CONN_ENET0_MDIO			0x06000020
+			IMX8DXL_ENET0_RGMII_RXC_CONN_ENET0_RGMII_RXC		0x00000060
+			IMX8DXL_ENET0_RGMII_RXD0_CONN_ENET0_RGMII_RXD0		0x00000060
+			IMX8DXL_ENET0_RGMII_RXD1_CONN_ENET0_RGMII_RXD1		0x00000060
+			IMX8DXL_ENET0_RGMII_RXD2_CONN_ENET0_RGMII_RXD2		0x00000060
+			IMX8DXL_ENET0_RGMII_RXD3_CONN_ENET0_RGMII_RXD3		0x00000060
+			IMX8DXL_ENET0_RGMII_RX_CTL_CONN_ENET0_RGMII_RX_CTL	0x00000060
+			IMX8DXL_ENET0_RGMII_TXC_CONN_ENET0_RGMII_TXC		0x00000060
+			IMX8DXL_ENET0_RGMII_TXD0_CONN_ENET0_RGMII_TXD0		0x00000060
+			IMX8DXL_ENET0_RGMII_TXD1_CONN_ENET0_RGMII_TXD1		0x00000060
+			IMX8DXL_ENET0_RGMII_TXD2_CONN_ENET0_RGMII_TXD2		0x00000060
+			IMX8DXL_ENET0_RGMII_TXD3_CONN_ENET0_RGMII_TXD3		0x00000060
+			IMX8DXL_ENET0_RGMII_TX_CTL_CONN_ENET0_RGMII_TX_CTL	0x00000060
+		>;
+	};
+
+	pinctrl_lpspi3: lpspi3grp {
+		fsl,pins = <
+			IMX8DXL_SPI3_SCK_ADMA_SPI3_SCK		0x6000040
+			IMX8DXL_SPI3_SDO_ADMA_SPI3_SDO		0x6000040
+			IMX8DXL_SPI3_SDI_ADMA_SPI3_SDI		0x6000040
+			IMX8DXL_SPI3_CS1_ADMA_SPI3_CS1		0x6000040
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			IMX8DXL_SPI1_SCK_ADMA_I2C2_SDA		0x06000021
+			IMX8DXL_SPI1_SDO_ADMA_I2C2_SCL		0x06000021
+		>;
+	};
+
+	pinctrl_cm40_lpuart: cm40lpuartgrp {
+		fsl,pins = <
+			IMX8DXL_ADC_IN2_M40_UART0_RX		0x06000020
+			IMX8DXL_ADC_IN3_M40_UART0_TX		0x06000020
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			IMX8DXL_SPI1_CS0_ADMA_I2C3_SDA		0x06000021
+			IMX8DXL_SPI1_SDI_ADMA_I2C3_SCL		0x06000021
+		>;
+	};
+
+	pinctrl_lpuart0: lpuart0grp {
+		fsl,pins = <
+			IMX8DXL_UART0_RX_ADMA_UART0_RX		0x06000020
+			IMX8DXL_UART0_TX_ADMA_UART0_TX		0x06000020
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			IMX8DXL_EMMC0_CLK_CONN_EMMC0_CLK	0x06000041
+			IMX8DXL_EMMC0_CMD_CONN_EMMC0_CMD	0x00000021
+			IMX8DXL_EMMC0_DATA0_CONN_EMMC0_DATA0	0x00000021
+			IMX8DXL_EMMC0_DATA1_CONN_EMMC0_DATA1	0x00000021
+			IMX8DXL_EMMC0_DATA2_CONN_EMMC0_DATA2	0x00000021
+			IMX8DXL_EMMC0_DATA3_CONN_EMMC0_DATA3	0x00000021
+			IMX8DXL_EMMC0_DATA4_CONN_EMMC0_DATA4	0x00000021
+			IMX8DXL_EMMC0_DATA5_CONN_EMMC0_DATA5	0x00000021
+			IMX8DXL_EMMC0_DATA6_CONN_EMMC0_DATA6	0x00000021
+			IMX8DXL_EMMC0_DATA7_CONN_EMMC0_DATA7	0x00000021
+			IMX8DXL_EMMC0_STROBE_CONN_EMMC0_STROBE	0x00000041
+		>;
+	};
+
+	pinctrl_usdhc2_gpio: usdhc2gpiogrp {
+		fsl,pins = <
+			IMX8DXL_ENET0_RGMII_TX_CTL_LSIO_GPIO4_IO30	0x00000040 /* RESET_B */
+			IMX8DXL_ENET0_RGMII_TXD1_LSIO_GPIO5_IO00	0x00000021 /* WP */
+			IMX8DXL_ENET0_RGMII_TXD2_LSIO_GPIO5_IO01	0x00000021 /* CD */
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			IMX8DXL_ENET0_RGMII_RXC_CONN_USDHC1_CLK		0x06000041
+			IMX8DXL_ENET0_RGMII_RX_CTL_CONN_USDHC1_CMD	0x00000021
+			IMX8DXL_ENET0_RGMII_RXD0_CONN_USDHC1_DATA0	0x00000021
+			IMX8DXL_ENET0_RGMII_RXD1_CONN_USDHC1_DATA1	0x00000021
+			IMX8DXL_ENET0_RGMII_RXD2_CONN_USDHC1_DATA2	0x00000021
+			IMX8DXL_ENET0_RGMII_RXD3_CONN_USDHC1_DATA3	0x00000021
+			IMX8DXL_ENET0_RGMII_TXD0_CONN_USDHC1_VSELECT	0x00000021
+		>;
+	};
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8dxl-ss-adma.dtsi b/arch/arm64/boot/dts/freescale/imx8dxl-ss-adma.dtsi
new file mode 100644
index 000000000000..795d1d472fae
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8dxl-ss-adma.dtsi
@@ -0,0 +1,52 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2019~2020, 2022 NXP
+ */
+
+&audio_ipg_clk {
+	clock-frequency = <160000000>;
+};
+
+&dma_ipg_clk {
+	clock-frequency = <160000000>;
+};
+
+&i2c0 {
+	compatible = "fsl,imx8dxl-lpi2c", "fsl,imx8qxp-lpi2c", "fsl,imx7ulp-lpi2c";
+	interrupts = <GIC_SPI 222 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&i2c1 {
+	compatible = "fsl,imx8dxl-lpi2c", "fsl,imx8qxp-lpi2c", "fsl,imx7ulp-lpi2c";
+	interrupts = <GIC_SPI 223 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&i2c2 {
+	compatible = "fsl,imx8qxp-lpi2c", "fsl,imx7ulp-lpi2c";
+	interrupts = <GIC_SPI 224 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&i2c3 {
+	compatible = "fsl,imx8qxp-lpi2c", "fsl,imx7ulp-lpi2c";
+	interrupts = <GIC_SPI 225 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&lpuart0 {
+	compatible = "fsl,imx8qxp-lpuart", "fsl,imx7ulp-lpuart";
+	interrupts = <GIC_SPI 228 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&lpuart1 {
+	compatible = "fsl,imx8qxp-lpuart", "fsl,imx7ulp-lpuart";
+	interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&lpuart2 {
+	compatible = "fsl,imx8qxp-lpuart", "fsl,imx7ulp-lpuart";
+	interrupts = <GIC_SPI 230 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&lpuart3 {
+	compatible = "fsl,imx8qxp-lpuart", "fsl,imx7ulp-lpuart";
+	interrupts = <GIC_SPI 231 IRQ_TYPE_LEVEL_HIGH>;
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8dxl-ss-conn.dtsi b/arch/arm64/boot/dts/freescale/imx8dxl-ss-conn.dtsi
new file mode 100644
index 000000000000..69c4849f2132
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8dxl-ss-conn.dtsi
@@ -0,0 +1,142 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2019~2020, 2022 NXP
+ */
+
+/delete-node/ &enet1_lpcg;
+/delete-node/ &fec2;
+
+&conn_subsys {
+	conn_enet0_root_clk: clock-conn-enet0-root {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <250000000>;
+		clock-output-names = "conn_enet0_root_clk";
+	};
+
+	eqos: ethernet@5b050000 {
+		compatible = "nxp,imx8dxl-dwmac-eqos", "snps,dwmac-5.10a";
+		reg = <0x5b050000 0x10000>;
+		interrupt-parent = <&gic>;
+		interrupts = <GIC_SPI 163 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "eth_wake_irq", "macirq";
+		clocks = <&eqos_lpcg IMX_LPCG_CLK_4>,
+			 <&eqos_lpcg IMX_LPCG_CLK_6>,
+			 <&eqos_lpcg IMX_LPCG_CLK_0>,
+			 <&eqos_lpcg IMX_LPCG_CLK_5>,
+			 <&eqos_lpcg IMX_LPCG_CLK_2>;
+		clock-names = "stmmaceth", "pclk", "ptp_ref", "tx", "mem";
+		assigned-clocks = <&clk IMX_SC_R_ENET_1 IMX_SC_PM_CLK_PER>;
+		assigned-clock-rates = <125000000>;
+		power-domains = <&pd IMX_SC_R_ENET_1>;
+		status = "disabled";
+	};
+
+	usbotg2: usb@5b0e0000 {
+		compatible = "fsl,imx8dxl-usb", "fsl,imx7ulp-usb";
+		reg = <0x5b0e0000 0x200>;
+		interrupt-parent = <&gic>;
+		interrupts = <GIC_SPI 166 IRQ_TYPE_LEVEL_HIGH>;
+		fsl,usbphy = <&usbphy2>;
+		fsl,usbmisc = <&usbmisc2 0>;
+		/*
+		 * usbotg1 and usbotg2 share one clcok.
+		 * scu firmware disables the access to the clock and keeps
+		 * it always on in case other core (M4) uses one of these.
+		 */
+		clocks = <&clk_dummy>;
+		ahb-burst-config = <0x0>;
+		tx-burst-size-dword = <0x10>;
+		rx-burst-size-dword = <0x10>;
+		#stream-id-cells = <1>;
+		power-domains = <&pd IMX_SC_R_USB_1>;
+		status = "disabled";
+
+		clk_dummy: clock-dummy {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <0>;
+			clock-output-names = "clk_dummy";
+		};
+	};
+
+	usbmisc2: usbmisc@5b0e0200 {
+		#index-cells = <1>;
+		compatible = "fsl,imx7ulp-usbmisc";
+		reg = <0x5b0e0200 0x200>;
+	};
+
+	usbphy2: usbphy@0x5b110000 {
+		compatible = "fsl,imx8dxl-usbphy", "fsl,imx7ulp-usbphy";
+		reg = <0x5b110000 0x1000>;
+		clocks = <&usb2_2_lpcg IMX_LPCG_CLK_7>;
+		power-domains = <&pd IMX_SC_R_USB_1_PHY>;
+		status = "disabled";
+	};
+
+	eqos_lpcg: clock-controller@5b240000 {
+		compatible = "fsl,imx8qxp-lpcg";
+		reg = <0x5b240000 0x10000>;
+		#clock-cells = <1>;
+		clocks = <&conn_enet0_root_clk>,
+			 <&conn_axi_clk>,
+			 <&conn_axi_clk>,
+			 <&clk IMX_SC_R_ENET_1 IMX_SC_PM_CLK_PER>,
+			 <&conn_ipg_clk>;
+		clock-indices = <IMX_LPCG_CLK_0>, <IMX_LPCG_CLK_2>,
+				<IMX_LPCG_CLK_4>, <IMX_LPCG_CLK_5>,
+				<IMX_LPCG_CLK_6>;
+		clock-output-names = "eqos_ptp",
+				     "eqos_mem_clk",
+				     "eqos_aclk",
+				     "eqos_clk",
+				     "eqos_csr_clk";
+		power-domains = <&pd IMX_SC_R_ENET_1>;
+	};
+
+	usb2_2_lpcg: clock-controller@5b280000 {
+		compatible = "fsl,imx8qxp-lpcg";
+		reg = <0x5b280000 0x10000>;
+		#clock-cells = <1>;
+		clock-indices = <IMX_LPCG_CLK_7>;
+		clocks = <&conn_ipg_clk>;
+		clock-output-names = "usboh3_2_phy_ipg_clk";
+		power-domains = <&pd IMX_SC_R_USB_1_PHY>;
+	};
+
+};
+
+&enet0_lpcg {
+	clocks = <&conn_enet0_root_clk>,
+		 <&conn_enet0_root_clk>,
+		 <&conn_axi_clk>,
+		 <&clk IMX_SC_R_ENET_0 IMX_SC_C_TXCLK>,
+		 <&conn_ipg_clk>,
+		 <&conn_ipg_clk>;
+};
+
+&fec1 {
+	compatible = "fsl,imx8qm-fec";
+	interrupts = <GIC_SPI 160 IRQ_TYPE_LEVEL_HIGH>,
+		     <GIC_SPI 158 IRQ_TYPE_LEVEL_HIGH>,
+		     <GIC_SPI 159 IRQ_TYPE_LEVEL_HIGH>,
+		     <GIC_SPI 161 IRQ_TYPE_LEVEL_HIGH>;
+	assigned-clocks = <&clk IMX_SC_R_ENET_0 IMX_SC_C_CLKDIV>;
+	assigned-clock-rates = <125000000>;
+};
+
+&usdhc1 {
+	compatible = "fsl,imx8dxl-usdhc", "fsl,imx8qxp-usdhc";
+	interrupts = <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&usdhc2 {
+	compatible = "fsl,imx8dxl-usdhc", "fsl,imx8qxp-usdhc";
+	interrupts = <GIC_SPI 139 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&usdhc3 {
+	compatible = "fsl,imx8dxl-usdhc", "fsl,imx8qxp-usdhc";
+	interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8dxl-ss-ddr.dtsi b/arch/arm64/boot/dts/freescale/imx8dxl-ss-ddr.dtsi
new file mode 100644
index 000000000000..550f513708d8
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8dxl-ss-ddr.dtsi
@@ -0,0 +1,9 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2020 NXP
+ */
+
+&ddr_pmu0 {
+	compatible = "fsl,imx8-ddr-pmu";
+	interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8dxl-ss-lsio.dtsi b/arch/arm64/boot/dts/freescale/imx8dxl-ss-lsio.dtsi
new file mode 100644
index 000000000000..815bd987b09b
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8dxl-ss-lsio.dtsi
@@ -0,0 +1,74 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2019~2020, 2022 NXP
+ */
+
+&lsio_gpio0 {
+	compatible = "fsl,imx8dxl-gpio", "fsl,imx35-gpio";
+	interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&lsio_gpio1 {
+	compatible = "fsl,imx8dxl-gpio", "fsl,imx35-gpio";
+	interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&lsio_gpio2 {
+	compatible = "fsl,imx8dxl-gpio", "fsl,imx35-gpio";
+	interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&lsio_gpio3 {
+	compatible = "fsl,imx8dxl-gpio", "fsl,imx35-gpio";
+	interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&lsio_gpio4 {
+	compatible = "fsl,imx8dxl-gpio", "fsl,imx35-gpio";
+	interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&lsio_gpio5 {
+	compatible = "fsl,imx8dxl-gpio", "fsl,imx35-gpio";
+	interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&lsio_gpio6 {
+	compatible = "fsl,imx8dxl-gpio", "fsl,imx35-gpio";
+	interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&lsio_gpio7 {
+	compatible = "fsl,imx8dxl-gpio", "fsl,imx35-gpio";
+	interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&lsio_mu0 {
+	compatible = "fsl,imx8qxp-mu", "fsl,imx6sx-mu";
+	interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&lsio_mu1 {
+	compatible = "fsl,imx8-mu-scu", "fsl,imx8qxp-mu", "fsl,imx6sx-mu";
+	interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&lsio_mu2 {
+	compatible = "fsl,imx8-mu-scu", "fsl,imx8qxp-mu", "fsl,imx6sx-mu";
+	interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&lsio_mu3 {
+	compatible = "fsl,imx8-mu-scu", "fsl,imx8qxp-mu", "fsl,imx6sx-mu";
+	interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&lsio_mu4 {
+	compatible = "fsl,imx8-mu-scu", "fsl,imx8qxp-mu", "fsl,imx6sx-mu";
+	interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&lsio_mu5 {
+	compatible = "fsl,imx8qxp-mu", "fsl,imx6sx-mu";
+	interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8dxl.dtsi b/arch/arm64/boot/dts/freescale/imx8dxl.dtsi
new file mode 100644
index 000000000000..5ddbda0b4def
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8dxl.dtsi
@@ -0,0 +1,238 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2019~2020, 2022 NXP
+ */
+
+#include <dt-bindings/clock/imx8-clock.h>
+#include <dt-bindings/firmware/imx/rsrc.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/pads-imx8dxl.h>
+#include <dt-bindings/thermal/thermal.h>
+
+/ {
+	interrupt-parent = <&gic>;
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	aliases {
+		ethernet0 = &fec1;
+		ethernet1 = &eqos;
+		gpio0 = &lsio_gpio0;
+		gpio1 = &lsio_gpio1;
+		gpio2 = &lsio_gpio2;
+		gpio3 = &lsio_gpio3;
+		gpio4 = &lsio_gpio4;
+		gpio5 = &lsio_gpio5;
+		gpio6 = &lsio_gpio6;
+		gpio7 = &lsio_gpio7;
+		mu1 = &lsio_mu1;
+	};
+
+	cpus: cpus {
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		/* We have 1 clusters with 2 Cortex-A35 cores */
+		A35_0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a35";
+			reg = <0x0 0x0>;
+			enable-method = "psci";
+			next-level-cache = <&A35_L2>;
+			clocks = <&clk IMX_SC_R_A35 IMX_SC_PM_CLK_CPU>;
+			#cooling-cells = <2>;
+			operating-points-v2 = <&a35_opp_table>;
+		};
+
+		A35_1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a35";
+			reg = <0x0 0x1>;
+			enable-method = "psci";
+			next-level-cache = <&A35_L2>;
+			clocks = <&clk IMX_SC_R_A35 IMX_SC_PM_CLK_CPU>;
+			#cooling-cells = <2>;
+			operating-points-v2 = <&a35_opp_table>;
+		};
+
+		A35_L2: l2-cache0 {
+			compatible = "cache";
+		};
+	};
+
+	a35_opp_table: opp-table {
+		compatible = "operating-points-v2";
+		opp-shared;
+
+		opp-900000000 {
+			opp-hz = /bits/ 64 <900000000>;
+			opp-microvolt = <1000000>;
+			clock-latency-ns = <150000>;
+		};
+
+		opp-1200000000 {
+			opp-hz = /bits/ 64 <1200000000>;
+			opp-microvolt = <1100000>;
+			clock-latency-ns = <150000>;
+			opp-suspend;
+		};
+	};
+
+	gic: interrupt-controller@51a00000 {
+		compatible = "arm,gic-v3";
+		reg = <0x0 0x51a00000 0 0x10000>, /* GIC Dist */
+		      <0x0 0x51b00000 0 0xc0000>; /* GICR (RD_base + SGI_base) */
+		#interrupt-cells = <3>;
+		interrupt-controller;
+		interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		dsp_reserved: dsp@92400000 {
+			reg = <0 0x92400000 0 0x2000000>;
+			no-map;
+		};
+	};
+
+	pmu {
+		compatible = "arm,armv8-pmuv3";
+		interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
+	psci {
+		compatible = "arm,psci-1.0";
+		method = "smc";
+	};
+
+	system-controller {
+		compatible = "fsl,imx-scu";
+		mbox-names = "tx0",
+			     "rx0",
+			     "gip3";
+		mboxes = <&lsio_mu1 0 0
+			  &lsio_mu1 1 0
+			  &lsio_mu1 3 3>;
+
+		pd: power-controller {
+			compatible = "fsl,scu-pd";
+			#power-domain-cells = <1>;
+			wakeup-irq = <160 163 235 236 237 228 229 230 231 238
+				     239 240 166 169>;
+		};
+
+		clk: clock-controller {
+			compatible = "fsl,imx8dxl-clk", "fsl,scu-clk";
+			#clock-cells = <2>;
+			clocks = <&xtal32k &xtal24m>;
+			clock-names = "xtal_32KHz", "xtal_24Mhz";
+		};
+
+		iomuxc: pinctrl {
+			compatible = "fsl,imx8dxl-iomuxc";
+		};
+
+		ocotp: ocotp {
+			compatible = "fsl,imx8qxp-scu-ocotp";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			fec_mac0: mac@2c4 {
+				reg = <0x2c4 6>;
+			};
+
+			fec_mac1: mac@2c6 {
+				reg = <0x2c6 6>;
+			};
+		};
+
+		rtc: rtc {
+			compatible = "fsl,imx8qxp-sc-rtc";
+		};
+
+		sc_pwrkey: keys {
+			compatible = "fsl,imx8qxp-sc-key", "fsl,imx-sc-key";
+			linux,keycode = <KEY_POWER>;
+			wakeup-source;
+		};
+
+		watchdog {
+			compatible = "fsl,imx-sc-wdt";
+			timeout-sec = <60>;
+		};
+
+		tsens: thermal-sensor {
+			compatible = "fsl,imx-sc-thermal";
+			#thermal-sensor-cells = <1>;
+		};
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW>, /* Physical Secure */
+			     <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW>, /* Physical Non-Secure */
+			     <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW>, /* Virtual */
+			     <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW>; /* Hypervisor */
+	};
+
+	thermal_zones: thermal-zones {
+		cpu-thermal0 {
+			polling-delay-passive = <250>;
+			polling-delay = <2000>;
+			thermal-sensors = <&tsens IMX_SC_R_SYSTEM>;
+
+			trips {
+				cpu_alert0: trip0 {
+					temperature = <107000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+				cpu_crit0: trip1 {
+					temperature = <127000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				map0 {
+					trip = <&cpu_alert0>;
+					cooling-device =
+					<&A35_0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+					<&A35_1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+	};
+
+	/* The two values below cannot be changed by the board */
+	xtal32k: clock-xtal32k {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		clock-output-names = "xtal_32KHz";
+	};
+
+	xtal24m: clock-xtal24m {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <24000000>;
+		clock-output-names = "xtal_24MHz";
+	};
+
+	/* sorted in register address */
+	#include "imx8-ss-adma.dtsi"
+	#include "imx8-ss-conn.dtsi"
+	#include "imx8-ss-ddr.dtsi"
+	#include "imx8-ss-lsio.dtsi"
+};
+
+#include "imx8dxl-ss-adma.dtsi"
+#include "imx8dxl-ss-conn.dtsi"
+#include "imx8dxl-ss-lsio.dtsi"
+#include "imx8dxl-ss-ddr.dtsi"
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-beacon-baseboard.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-beacon-baseboard.dtsi
index 6f5e63696ec0..03266bd90a06 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-beacon-baseboard.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm-beacon-baseboard.dtsi
@@ -3,6 +3,8 @@
  * Copyright 2020 Compass Electronics Group, LLC
  */
 
+#include <dt-bindings/phy/phy-imx8-pcie.h>
+
 / {
 	leds {
 		compatible = "gpio-leds";
@@ -34,6 +36,19 @@
 		};
 	};
 
+	pcie0_refclk: pcie0-refclk {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <100000000>;
+	};
+
+	pcie0_refclk_gated:  pcie0-refclk-gated {
+		compatible = "gpio-gate-clock";
+		clocks = <&pcie0_refclk>;
+		#clock-cells = <0>;
+		enable-gpios = <&pca6416_1 2 GPIO_ACTIVE_LOW>;
+	};
+
 	reg_audio: regulator-audio {
 		compatible = "regulator-fixed";
 		regulator-name = "3v3_aud";
@@ -43,6 +58,37 @@
 		enable-active-high;
 	};
 
+	reg_usbotg1: regulator-usbotg1 {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_usb_otg1>;
+		regulator-name = "usb_otg_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio4 29 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	reg_camera: regulator-camera {
+		compatible = "regulator-fixed";
+		regulator-name = "mipi_pwr";
+		regulator-min-microvolt = <2800000>;
+		regulator-max-microvolt = <2800000>;
+		gpio = <&pca6416_1 0 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		startup-delay-us = <100000>;
+	};
+
+	reg_pcie0: regulator-pcie {
+		compatible = "regulator-fixed";
+		regulator-name = "pci_pwr_en";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		enable-active-high;
+		gpio = <&pca6416_1 1 GPIO_ACTIVE_HIGH>;
+		startup-delay-us = <100000>;
+	};
+
 	reg_usdhc2_vmmc: regulator-usdhc2 {
 		compatible = "regulator-fixed";
 		regulator-name = "VSD_3V3";
@@ -67,6 +113,10 @@
 	};
 };
 
+&csi {
+	status = "okay";
+};
+
 &ecspi2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_espi2>;
@@ -90,6 +140,30 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_i2c2>;
 	status = "okay";
+
+	camera@3c {
+		compatible = "ovti,ov5640";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ov5640>;
+		reg = <0x3c>;
+		clocks = <&clk IMX8MM_CLK_CLKO1>;
+		clock-names = "xclk";
+		assigned-clocks = <&clk IMX8MM_CLK_CLKO1>;
+		assigned-clock-parents = <&clk IMX8MM_CLK_24M>;
+		assigned-clock-rates = <24000000>;
+		AVDD-supply = <&reg_camera>;  /* 2.8v */
+		powerdown-gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
+		reset-gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
+
+		port {
+			/* MIPI CSI-2 bus endpoint */
+			ov5640_to_mipi_csi2: endpoint {
+				remote-endpoint = <&imx8mm_mipi_csi_in>;
+				clock-lanes = <0>;
+				data-lanes = <1 2>;
+			};
+		};
+	};
 };
 
 &i2c4 {
@@ -141,6 +215,44 @@
 	};
 };
 
+&mipi_csi {
+	status = "okay";
+	ports {
+		port@0 {
+			imx8mm_mipi_csi_in: endpoint {
+				remote-endpoint = <&ov5640_to_mipi_csi2>;
+				data-lanes = <1 2>;
+			};
+		};
+	};
+};
+
+&pcie_phy {
+	fsl,refclk-pad-mode = <IMX8_PCIE_REFCLK_PAD_INPUT>;
+	fsl,tx-deemph-gen1 = <0x2d>;
+	fsl,tx-deemph-gen2 = <0xf>;
+	fsl,clkreq-unsupported;
+	clocks = <&pcie0_refclk_gated>;
+	clock-names = "ref";
+	status = "okay";
+};
+
+&pcie0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pcie0>;
+	reset-gpio = <&gpio4 21 GPIO_ACTIVE_LOW>;
+	clocks = <&clk IMX8MM_CLK_PCIE1_ROOT>, <&clk IMX8MM_CLK_PCIE1_AUX>,
+		 <&pcie0_refclk_gated>;
+	clock-names = "pcie", "pcie_aux", "pcie_bus";
+	assigned-clocks = <&clk IMX8MM_CLK_PCIE1_AUX>,
+			  <&clk IMX8MM_CLK_PCIE1_CTRL>;
+	assigned-clock-rates = <10000000>, <250000000>;
+	assigned-clock-parents = <&clk IMX8MM_SYS_PLL2_50M>,
+				 <&clk IMX8MM_SYS_PLL2_250M>;
+	vpcie-supply = <&reg_pcie0>;
+	status = "okay";
+};
+
 &sai3 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_sai3>;
@@ -166,9 +278,28 @@
 	pinctrl-0 = <&pinctrl_uart3>;
 	assigned-clocks = <&clk IMX8MM_CLK_UART3>;
 	assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_80M>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&usbotg1 {
+	vbus-supply = <&reg_usbotg1>;
+	disable-over-current;
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&usbotg2 {
+	pinctrl-names = "default";
+	disable-over-current;
+	dr_mode = "host";
 	status = "okay";
 };
 
+&usbphynop2 {
+	reset-gpios = <&pca6416_1 7 GPIO_ACTIVE_HIGH>;
+};
+
 &usdhc2 {
 	pinctrl-names = "default", "state_100mhz", "state_200mhz";
 	pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
@@ -209,12 +340,32 @@
 		>;
 	};
 
+	pinctrl_ov5640: ov5640grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO07_GPIO1_IO7		0x19
+			MX8MM_IOMUXC_GPIO1_IO06_GPIO1_IO6		0x19
+			MX8MM_IOMUXC_GPIO1_IO14_CCMSRCGPCMIX_CLKO1	0x59
+		>;
+	};
+
 	pinctrl_pcal6414: pcal6414-gpiogrp {
 		fsl,pins = <
 			MX8MM_IOMUXC_SAI2_MCLK_GPIO4_IO27		0x19
 		>;
 	};
 
+	pinctrl_reg_usb_otg1: usbotg1grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI3_RXC_GPIO4_IO29     0x19
+		>;
+	};
+
+	pinctrl_pcie0: pcie0grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI2_RXFS_GPIO4_IO21       0x41
+		>;
+	};
+
 	pinctrl_sai3: sai3grp {
 		fsl,pins = <
 			MX8MM_IOMUXC_SAI3_TXFS_SAI3_TX_SYNC     0xd6
@@ -236,6 +387,8 @@
 		fsl,pins = <
 			MX8MM_IOMUXC_ECSPI1_SCLK_UART3_DCE_RX	0x40
 			MX8MM_IOMUXC_ECSPI1_MOSI_UART3_DCE_TX	0x40
+			MX8MM_IOMUXC_ECSPI1_MISO_UART3_DCE_CTS_B	0x40
+			MX8MM_IOMUXC_ECSPI1_SS0_UART3_DCE_RTS_B	0x40
 		>;
 	};
 
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-beacon-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-beacon-som.dtsi
index 40f5e7a3b064..cf07987ccc10 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-beacon-som.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm-beacon-som.dtsi
@@ -263,7 +263,6 @@
 	bus-width = <4>;
 	non-removable;
 	cap-power-off-card;
-	pm-ignore-notify;
 	keep-power-in-suspend;
 	mmc-pwrseq = <&usdhc1_pwrseq>;
 	status = "okay";
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-data-modul-edm-sbc.dts b/arch/arm64/boot/dts/freescale/imx8mm-data-modul-edm-sbc.dts
new file mode 100644
index 000000000000..778bdbe228d3
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-data-modul-edm-sbc.dts
@@ -0,0 +1,997 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2022 Marek Vasut <marex@denx.de>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/net/qca-ar803x.h>
+#include <dt-bindings/phy/phy-imx8-pcie.h>
+#include "imx8mm.dtsi"
+
+/ {
+	model = "Data Modul i.MX8M Mini eDM SBC";
+	compatible = "dmo,imx8mm-data-modul-edm-sbc", "fsl,imx8mm";
+
+	aliases {
+		rtc0 = &rtc;
+		rtc1 = &snvs_rtc;
+	};
+
+	chosen {
+		stdout-path = &uart3;
+	};
+
+	memory@40000000 {
+		device_type = "memory";
+		/* There are 1/2/4 GiB options, adjusted by bootloader. */
+		reg = <0x0 0x40000000 0 0x40000000>;
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_panel_backlight>;
+		brightness-levels = <0 1 10 20 30 40 50 60 70 75 80 90 100>;
+		default-brightness-level = <7>;
+		enable-gpios = <&gpio3 0 GPIO_ACTIVE_HIGH>;
+		pwms = <&pwm1 0 5000000 0>;
+		/* Disabled by default, unless display board plugged in. */
+		status = "disabled";
+	};
+
+	clk_xtal25: clk-xtal25 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <25000000>;
+	};
+
+	panel: panel {
+		backlight = <&backlight>;
+		power-supply = <&reg_panel_vcc>;
+		/* Disabled by default, unless display board plugged in. */
+		status = "disabled";
+	};
+
+	reg_panel_vcc: regulator-panel-vcc {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_panel_vcc_reg>;
+		regulator-name = "PANEL_VCC";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio3 6 0>;
+		enable-active-high;
+		/* Disabled by default, unless display board plugged in. */
+		status = "disabled";
+	};
+
+	reg_usdhc2_vcc: regulator-usdhc2-vcc {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usdhc2_vcc_reg>;
+		regulator-name = "V_3V3_SD";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio2 19 0>;
+		enable-active-high;
+	};
+
+	watchdog-gpio {
+		/* TPS3813 */
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_watchdog_gpio>;
+		compatible = "linux,wdt-gpio";
+		always-enabled;
+		gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+		hw_algo = "level";
+		/* Reset triggers in 2..3 seconds */
+		hw_margin_ms = <1500>;
+		/* Disabled by default */
+		status = "disabled";
+	};
+};
+
+&A53_0 {
+	cpu-supply = <&buck2_reg>;
+};
+
+&A53_1 {
+	cpu-supply = <&buck2_reg>;
+};
+
+&A53_2 {
+	cpu-supply = <&buck2_reg>;
+};
+
+&A53_3 {
+	cpu-supply = <&buck2_reg>;
+};
+
+&ddrc {
+	operating-points-v2 = <&ddrc_opp_table>;
+
+	ddrc_opp_table: opp-table {
+		compatible = "operating-points-v2";
+
+		opp-25M {
+			opp-hz = /bits/ 64 <25000000>;
+		};
+
+		opp-100M {
+			opp-hz = /bits/ 64 <100000000>;
+		};
+
+		opp-750M {
+			opp-hz = /bits/ 64 <750000000>;
+		};
+	};
+};
+
+&ecspi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1>;
+	cs-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
+	status = "okay";
+
+	flash@0 {	/* W25Q128FVSI */
+		compatible = "jedec,spi-nor";
+		m25p,fast-read;
+		spi-max-frequency = <50000000>;
+		reg = <0>;
+	};
+};
+
+&ecspi2 {	/* Feature connector SPI */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi2>;
+	cs-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>;
+	/* Disabled by default, unless feature board plugged in. */
+	status = "disabled";
+};
+
+&ecspi3 {	/* Display connector SPI */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi3>;
+	cs-gpios = <&gpio5 25 GPIO_ACTIVE_LOW>;
+	/* Disabled by default, unless display board plugged in. */
+	status = "disabled";
+};
+
+&fec1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_fec1>;
+	phy-mode = "rgmii-id";
+	phy-handle = <&fec1_phy>;
+	phy-supply = <&buck4_reg>;
+	fsl,magic-packet;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* Atheros AR8031 PHY */
+		fec1_phy: ethernet-phy@0 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <0>;
+			/*
+			 * Dedicated ENET_WOL# signal is unused, the PHY
+			 * can wake the SoC up via INT signal as well.
+			 */
+			interrupts-extended = <&gpio1 15 IRQ_TYPE_LEVEL_LOW>;
+			reset-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <10000>;
+			reset-deassert-us = <10000>;
+			qca,clk-out-frequency = <125000000>;
+			qca,clk-out-strength = <AR803X_STRENGTH_FULL>;
+			qca,keep-pll-enabled;
+			vddio-supply = <&vddio>;
+
+			vddio: vddio-regulator {
+				regulator-name = "VDDIO";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+
+			vddh: vddh-regulator {
+				regulator-name = "VDDH";
+			};
+		};
+	};
+};
+
+&gpio1 {
+	gpio-line-names =
+		"", "ENET_RST#", "WDOG_B#", "PMIC_INT#",
+		"", "M2-B_PCIE_RST#", "M2-B_PCIE_WAKE#", "RTC_IRQ#",
+		"WDOG_KICK#", "M2-B_PCIE_CLKREQ#",
+		"USB1_OTG_ID_3V3", "ENET_WOL#",
+		"", "", "", "ENET_INT#",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "";
+};
+
+&gpio2 {
+	gpio-line-names =
+		"MEMCFG2", "MEMCFG1", "DSI_RESET_1V8#", "DSI_IRQ_1V8#",
+		"M2-B_FULL_CARD_PWROFF_1V8#", "EEPROM_WP_1V8#",
+		"PCIE_CLK_GEN_CLKPWRGD_PD_1V8#", "GRAPHICS_PRSNT_1V8#",
+		"MEMCFG0", "WDOG_EN",
+		"M2-B_W_DISABLE1_WWAN_1V8#", "M2-B_W_DISABLE2_GPS_1V8#",
+		"", "", "", "",
+		"", "", "", "SD2_RESET#", "", "", "", "",
+		"", "", "", "", "", "", "", "";
+};
+
+&gpio3 {
+	gpio-line-names =
+		"BL_ENABLE_1V8", "PG_V_IN_VAR#", "", "",
+		"", "", "TFT_ENABLE_1V8", "GRAPHICS_GPIO0_1V8",
+		"CSI_PD_1V8", "CSI_RESET_1V8#", "", "",
+		"", "", "", "",
+		"", "", "", "M2-B_WAKE_WWAN_1V8#",
+		"M2-B_RESET_1V8#", "", "", "",
+		"", "", "", "", "", "", "", "";
+};
+
+&gpio4 {
+	gpio-line-names =
+		"NC0", "NC1", "BOOTCFG0", "BOOTCFG1",
+		"BOOTCFG2", "BOOTCFG3", "BOOTCFG4", "BOOTCFG5",
+		"BOOTCFG6", "BOOTCFG7", "NC10", "NC11",
+		"BOOTCFG8", "BOOTCFG9", "BOOTCFG10", "BOOTCFG11",
+		"BOOTCFG12", "BOOTCFG13", "BOOTCFG14", "BOOTCFG15",
+		"NC20", "", "", "",
+		"", "CAN_INT#", "CAN_RST#", "GPIO4_IO27",
+		"DIS_USB_DN2", "", "", "";
+};
+
+&gpio5 {
+	gpio-line-names =
+		"", "DIS_USB_DN1", "USBHUB_RESET#", "GPIO5_IO03",
+		"GPIO5_IO04", "", "", "",
+		"", "SPI1_CS#", "", "",
+		"", "SPI2_CS#", "I2C1_SCL_3V3", "I2C1_SDA_3V3",
+		"I2C2_SCL_3V3", "I2C2_SDA_3V3", "I2C3_SCL_3V3", "I2C3_SDA_3V3",
+		"I2C4_SCL_3V3", "I2C4_SDA_3V3", "", "",
+		"", "SPI3_CS#", "", "", "", "", "", "";
+};
+
+&i2c1 {
+	/* IMX8MM ERRATA e7805 -- I2C is limited to 384 kHz due to SoC bug */
+	clock-frequency = <100000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	pinctrl-1 = <&pinctrl_i2c1_gpio>;
+	scl-gpios = <&gpio5 14 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio5 15 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "okay";
+
+	pmic: pmic@4b {
+		compatible = "rohm,bd71847";
+		reg = <0x4b>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_pmic>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <3 IRQ_TYPE_EDGE_FALLING>;
+		rohm,reset-snvs-powered;
+
+		/*
+		 * i.MX 8M Mini Data Sheet for Consumer Products
+		 * 3.1.3 Operating ranges
+		 * MIMX8MM4DVTLZAA
+		 */
+		regulators {
+			/* VDD_SOC */
+			buck1_reg: BUCK1 {
+				regulator-name = "buck1";
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <850000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <1250>;
+			};
+
+			/* VDD_ARM */
+			buck2_reg: BUCK2 {
+				regulator-name = "buck2";
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <1050000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <1250>;
+				rohm,dvs-run-voltage = <1000000>;
+				rohm,dvs-idle-voltage = <950000>;
+			};
+
+			/* VDD_DRAM, BUCK5 */
+			buck3_reg: BUCK3 {
+				regulator-name = "buck3";
+				/* 1.5 GHz DDR bus clock */
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			/* 3V3_VDD, BUCK6 */
+			buck4_reg: BUCK4 {
+				regulator-name = "buck4";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			/* 1V8_VDD, BUCK7 */
+			buck5_reg: BUCK5 {
+				regulator-name = "buck5";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			/* 1V1_NVCC_DRAM, BUCK8 */
+			buck6_reg: BUCK6 {
+				regulator-name = "buck6";
+				regulator-min-microvolt = <1100000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			/* 1V8_NVCC_SNVS */
+			ldo1_reg: LDO1 {
+				regulator-name = "ldo1";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			/* 0V8_VDD_SNVS */
+			ldo2_reg: LDO2 {
+				regulator-name = "ldo2";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			/* 1V8_VDDA */
+			ldo3_reg: LDO3 {
+				regulator-name = "ldo3";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			/* 0V9_VDD_PHY */
+			ldo4_reg: LDO4 {
+				regulator-name = "ldo4";
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <900000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			/* 1V2_VDD_PHY */
+			ldo6_reg: LDO6 {
+				regulator-name = "ldo6";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+		};
+	};
+};
+
+&i2c2 {
+	/* IMX8MM ERRATA e7805 -- I2C is limited to 384 kHz due to SoC bug */
+	clock-frequency = <100000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	pinctrl-1 = <&pinctrl_i2c2_gpio>;
+	scl-gpios = <&gpio5 16 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio5 17 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "okay";
+
+	usb-hub@2c {
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usb_hub>;
+		compatible = "microchip,usb2514bi";
+		reg = <0x2c>;
+		individual-port-switching;
+		reset-gpios = <&gpio5 2 GPIO_ACTIVE_LOW>;
+		self-powered;
+	};
+
+	eeprom: eeprom@50 {
+		compatible = "atmel,24c32";
+		reg = <0x50>;
+		pagesize = <32>;
+	};
+
+	rtc: rtc@68 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_rtc>;
+		compatible = "st,m41t62";
+		reg = <0x68>;
+		interrupts-extended = <&gpio1 7 IRQ_TYPE_LEVEL_LOW>;
+	};
+
+	pcieclk: clk@6a {
+		compatible = "renesas,9fgv0241";
+		reg = <0x6a>;
+		clocks = <&clk_xtal25>;
+		#clock-cells = <1>;
+	};
+};
+
+&i2c3 {	/* Display connector I2C */
+	/* IMX8MM ERRATA e7805 -- I2C is limited to 384 kHz due to SoC bug */
+	clock-frequency = <320000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	pinctrl-1 = <&pinctrl_i2c3_gpio>;
+	scl-gpios = <&gpio5 18 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio5 19 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "okay";
+};
+
+&i2c4 {	/* Feature connector I2C */
+	/* IMX8MM ERRATA e7805 -- I2C is limited to 384 kHz due to SoC bug */
+	clock-frequency = <320000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c4>;
+	pinctrl-1 = <&pinctrl_i2c4_gpio>;
+	scl-gpios = <&gpio5 20 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio5 21 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hog_feature>, <&pinctrl_hog_misc>,
+		    <&pinctrl_hog_panel>, <&pinctrl_hog_sbc>,
+		    <&pinctrl_panel_expansion>;
+
+	pinctrl_ecspi1: ecspi1-grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_ECSPI1_SCLK_ECSPI1_SCLK		0x44
+			MX8MM_IOMUXC_ECSPI1_MOSI_ECSPI1_MOSI		0x44
+			MX8MM_IOMUXC_ECSPI1_MISO_ECSPI1_MISO		0x44
+			MX8MM_IOMUXC_ECSPI1_SS0_GPIO5_IO9		0x40
+		>;
+	};
+
+	pinctrl_ecspi2: ecspi2-grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK		0x44
+			MX8MM_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI		0x44
+			MX8MM_IOMUXC_ECSPI2_MISO_ECSPI2_MISO		0x44
+			MX8MM_IOMUXC_ECSPI2_SS0_GPIO5_IO13		0x40
+		>;
+	};
+
+	pinctrl_ecspi3: ecspi3-grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_UART1_RXD_ECSPI3_SCLK		0x44
+			MX8MM_IOMUXC_UART1_TXD_ECSPI3_MOSI		0x44
+			MX8MM_IOMUXC_UART2_RXD_ECSPI3_MISO		0x44
+			MX8MM_IOMUXC_UART2_TXD_GPIO5_IO25		0x40
+		>;
+	};
+
+	pinctrl_fec1: fec1-grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_ENET_MDC_ENET1_MDC			0x3
+			MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO		0x3
+			MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0		0x91
+			MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1		0x91
+			MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2		0x91
+			MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3		0x91
+			MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC		0x91
+			MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL	0x91
+			MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0		0x1f
+			MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1		0x1f
+			MX8MM_IOMUXC_ENET_TD2_ENET1_RGMII_TD2		0x1f
+			MX8MM_IOMUXC_ENET_TD3_ENET1_RGMII_TD3		0x1f
+			MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC		0x1f
+			MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL	0x1f
+			/* ENET_RST# */
+			MX8MM_IOMUXC_GPIO1_IO01_GPIO1_IO1		0x6
+			/* ENET_WOL# */
+			MX8MM_IOMUXC_GPIO1_IO11_GPIO1_IO11		0x40000090
+			/* ENET_INT# */
+			MX8MM_IOMUXC_GPIO1_IO15_GPIO1_IO15		0x40000090
+		>;
+	};
+
+	pinctrl_hog_feature: hog-feature-grp {
+		fsl,pins = <
+			/* GPIO4_IO27 */
+			MX8MM_IOMUXC_SAI2_MCLK_GPIO4_IO27		0x40000006
+			/* GPIO5_IO03 */
+			MX8MM_IOMUXC_SPDIF_TX_GPIO5_IO3			0x40000006
+			/* GPIO5_IO04 */
+			MX8MM_IOMUXC_SPDIF_RX_GPIO5_IO4			0x40000006
+
+			/* CAN_INT# */
+			MX8MM_IOMUXC_SAI2_TXC_GPIO4_IO25		0x40000090
+			/* CAN_RST# */
+			MX8MM_IOMUXC_SAI2_TXD0_GPIO4_IO26		0x26
+		>;
+	};
+
+	pinctrl_hog_panel: hog-panel-grp {
+		fsl,pins = <
+			/* GRAPHICS_GPIO0_1V8 */
+			MX8MM_IOMUXC_NAND_DATA01_GPIO3_IO7		0x26
+		>;
+	};
+
+	pinctrl_hog_misc: hog-misc-grp {
+		fsl,pins = <
+			/* PG_V_IN_VAR# */
+			MX8MM_IOMUXC_NAND_CE0_B_GPIO3_IO1		0x40000000
+			/* CSI_PD_1V8 */
+			MX8MM_IOMUXC_NAND_DATA02_GPIO3_IO8		0x0
+			/* CSI_RESET_1V8# */
+			MX8MM_IOMUXC_NAND_DATA03_GPIO3_IO9		0x0
+
+			/* DIS_USB_DN1 */
+			MX8MM_IOMUXC_SAI3_TXD_GPIO5_IO1			0x0
+			/* DIS_USB_DN2 */
+			MX8MM_IOMUXC_SAI3_RXFS_GPIO4_IO28		0x0
+
+			/* EEPROM_WP_1V8# */
+			MX8MM_IOMUXC_SD1_DATA3_GPIO2_IO5		0x100
+			/* PCIE_CLK_GEN_CLKPWRGD_PD_1V8# */
+			MX8MM_IOMUXC_SD1_DATA4_GPIO2_IO6		0x0
+			/* GRAPHICS_PRSNT_1V8# */
+			MX8MM_IOMUXC_SD1_DATA5_GPIO2_IO7		0x40000000
+
+			/* CLK_CCM_CLKO1_3V3 */
+			MX8MM_IOMUXC_GPIO1_IO14_CCMSRCGPCMIX_CLKO1	0x10
+		>;
+	};
+
+	pinctrl_hog_sbc: hog-sbc-grp {
+		fsl,pins = <
+			/* MEMCFG[0..2] straps */
+			MX8MM_IOMUXC_SD1_DATA6_GPIO2_IO8		0x40000140
+			MX8MM_IOMUXC_SD1_CMD_GPIO2_IO1			0x40000140
+			MX8MM_IOMUXC_SD1_CLK_GPIO2_IO0			0x40000140
+
+			/* BOOT_CFG[0..15] straps */
+			MX8MM_IOMUXC_SAI1_RXD0_GPIO4_IO2		0x40000000
+			MX8MM_IOMUXC_SAI1_RXD1_GPIO4_IO3		0x40000000
+			MX8MM_IOMUXC_SAI1_RXD2_GPIO4_IO4		0x40000000
+			MX8MM_IOMUXC_SAI1_RXD3_GPIO4_IO5		0x40000000
+			MX8MM_IOMUXC_SAI1_RXD4_GPIO4_IO6		0x40000000
+			MX8MM_IOMUXC_SAI1_RXD5_GPIO4_IO7		0x40000000
+			MX8MM_IOMUXC_SAI1_RXD6_GPIO4_IO8		0x40000000
+			MX8MM_IOMUXC_SAI1_RXD7_GPIO4_IO9		0x40000000
+			MX8MM_IOMUXC_SAI1_TXD0_GPIO4_IO12		0x40000000
+			MX8MM_IOMUXC_SAI1_TXD1_GPIO4_IO13		0x40000000
+			MX8MM_IOMUXC_SAI1_TXD2_GPIO4_IO14		0x40000000
+			MX8MM_IOMUXC_SAI1_TXD3_GPIO4_IO15		0x40000000
+			MX8MM_IOMUXC_SAI1_TXD4_GPIO4_IO16		0x40000000
+			MX8MM_IOMUXC_SAI1_TXD5_GPIO4_IO17		0x40000000
+			MX8MM_IOMUXC_SAI1_TXD6_GPIO4_IO18		0x40000000
+			MX8MM_IOMUXC_SAI1_TXD7_GPIO4_IO19		0x40000000
+
+			/* Not connected pins */
+			MX8MM_IOMUXC_SAI1_MCLK_GPIO4_IO20		0x0
+			MX8MM_IOMUXC_SAI1_TXFS_GPIO4_IO10		0x0
+			MX8MM_IOMUXC_SAI1_TXC_GPIO4_IO11		0x0
+			MX8MM_IOMUXC_SAI1_RXFS_GPIO4_IO0		0x0
+			MX8MM_IOMUXC_SAI1_RXC_GPIO4_IO1			0x0
+		>;
+	};
+
+	pinctrl_i2c1: i2c1-grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL			0x40000084
+			MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA			0x40000084
+		>;
+	};
+
+	pinctrl_i2c1_gpio: i2c1-gpio-grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_I2C1_SCL_GPIO5_IO14		0x84
+			MX8MM_IOMUXC_I2C1_SDA_GPIO5_IO15		0x84
+		>;
+	};
+
+	pinctrl_i2c2: i2c2-grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_I2C2_SCL_I2C2_SCL			0x40000084
+			MX8MM_IOMUXC_I2C2_SDA_I2C2_SDA			0x40000084
+		>;
+	};
+
+	pinctrl_i2c2_gpio: i2c2-gpio-grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_I2C2_SCL_GPIO5_IO16		0x84
+			MX8MM_IOMUXC_I2C2_SDA_GPIO5_IO17		0x84
+		>;
+	};
+
+	pinctrl_i2c3: i2c3-grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_I2C3_SCL_I2C3_SCL			0x40000084
+			MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA			0x40000084
+		>;
+	};
+
+	pinctrl_i2c3_gpio: i2c3-gpio-grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_I2C3_SCL_GPIO5_IO18		0x84
+			MX8MM_IOMUXC_I2C3_SDA_GPIO5_IO19		0x84
+		>;
+	};
+
+	pinctrl_i2c4: i2c4-grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_I2C4_SCL_I2C4_SCL			0x40000084
+			MX8MM_IOMUXC_I2C4_SDA_I2C4_SDA			0x40000084
+		>;
+	};
+
+	pinctrl_i2c4_gpio: i2c4-gpio-grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_I2C4_SCL_GPIO5_IO20		0x84
+			MX8MM_IOMUXC_I2C4_SDA_GPIO5_IO21		0x84
+		>;
+	};
+
+	pinctrl_panel_backlight: panel-backlight-grp {
+		fsl,pins = <
+			/* BL_ENABLE_1V8 */
+			MX8MM_IOMUXC_NAND_ALE_GPIO3_IO0			0x104
+		>;
+	};
+
+	pinctrl_panel_expansion: panel-expansion-grp {
+		fsl,pins = <
+			/* DSI_RESET_1V8# */
+			MX8MM_IOMUXC_SD1_DATA0_GPIO2_IO2		0x2
+			/* DSI_IRQ_1V8# */
+			MX8MM_IOMUXC_SD1_DATA1_GPIO2_IO3		0x40000090
+		>;
+	};
+
+	pinctrl_panel_vcc_reg: panel-vcc-grp {
+		fsl,pins = <
+			/* TFT_ENABLE_1V8 */
+			MX8MM_IOMUXC_NAND_DATA00_GPIO3_IO6		0x104
+		>;
+	};
+
+	pinctrl_panel_pwm: panel-pwm-grp {
+		fsl,pins = <
+			/* BL_PWM_3V3 */
+			MX8MM_IOMUXC_SPDIF_EXT_CLK_PWM1_OUT		0x12
+		>;
+	};
+
+	pinctrl_pcie0: pcie-grp {
+		fsl,pins = <
+			/* M2-B_RESET_1V8# */
+			MX8MM_IOMUXC_SAI5_RXC_GPIO3_IO20		0x102
+			/* M2-B_PCIE_RST# */
+			MX8MM_IOMUXC_GPIO1_IO05_GPIO1_IO5		0x2
+			/* M2-B_FULL_CARD_PWROFF_1V8# */
+			MX8MM_IOMUXC_SD1_DATA2_GPIO2_IO4		0x102
+			/* M2-B_W_DISABLE1_WWAN_1V8# */
+			MX8MM_IOMUXC_SD1_RESET_B_GPIO2_IO10		0x102
+			/* M2-B_W_DISABLE2_GPS_1V8# */
+			MX8MM_IOMUXC_SD1_STROBE_GPIO2_IO11		0x102
+			/* CLK_M2_32K768 */
+			MX8MM_IOMUXC_GPIO1_IO00_ANAMIX_REF_CLK_32K	0x14
+			/* M2-B_WAKE_WWAN_1V8# */
+			MX8MM_IOMUXC_SAI5_RXFS_GPIO3_IO19		0x40000140
+			/* M2-B_PCIE_WAKE# */
+			MX8MM_IOMUXC_GPIO1_IO06_GPIO1_IO6		0x40000140
+			/* M2-B_PCIE_CLKREQ# */
+			MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9		0x40000140
+		>;
+	};
+
+	pinctrl_pmic: pmic-grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3		0x40000090
+		>;
+	};
+
+	pinctrl_rtc: rtc-grp {
+		fsl,pins = <
+			/* RTC_IRQ# */
+			MX8MM_IOMUXC_GPIO1_IO07_GPIO1_IO7		0x40000090
+		>;
+	};
+
+	pinctrl_sai5: sai5-grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI5_MCLK_SAI5_MCLK		0x100
+			MX8MM_IOMUXC_SAI5_RXD0_SAI5_RX_DATA0		0x0
+			MX8MM_IOMUXC_SAI5_RXD1_SAI5_TX_SYNC		0x100
+			MX8MM_IOMUXC_SAI5_RXD2_SAI5_TX_BCLK		0x100
+			MX8MM_IOMUXC_SAI5_RXD3_SAI5_TX_DATA0		0x100
+		>;
+	};
+
+	pinctrl_uart1: uart1-grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI2_RXC_UART1_DCE_RX		0x90
+			MX8MM_IOMUXC_SAI2_RXD0_UART1_DCE_RTS_B		0x90
+			MX8MM_IOMUXC_SAI2_RXFS_UART1_DCE_TX		0x50
+			MX8MM_IOMUXC_SAI2_TXFS_UART1_DCE_CTS_B		0x50
+		>;
+	};
+
+	pinctrl_uart2: uart2-grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI3_RXC_UART2_DCE_CTS_B		0x50
+			MX8MM_IOMUXC_SAI3_RXD_UART2_DCE_RTS_B		0x90
+			MX8MM_IOMUXC_SAI3_TXC_UART2_DCE_TX		0x50
+			MX8MM_IOMUXC_SAI3_TXFS_UART2_DCE_RX		0x90
+		>;
+	};
+
+	pinctrl_uart3: uart3-grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_UART3_RXD_UART3_DCE_RX		0x40
+			MX8MM_IOMUXC_UART3_TXD_UART3_DCE_TX		0x40
+		>;
+	};
+
+	pinctrl_uart4: uart4-grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_UART4_RXD_UART4_DCE_RX		0x40
+			MX8MM_IOMUXC_UART4_TXD_UART4_DCE_TX		0x40
+		>;
+	};
+
+	pinctrl_usb_hub: usb-hub-grp {
+		fsl,pins = <
+			/* USBHUB_RESET# */
+			MX8MM_IOMUXC_SAI3_MCLK_GPIO5_IO2		0x4
+		>;
+	};
+
+	pinctrl_usb_otg1: usb-otg1-grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO10_GPIO1_IO10		0x40000000
+			MX8MM_IOMUXC_GPIO1_IO12_USB1_OTG_PWR		0x4
+			MX8MM_IOMUXC_GPIO1_IO13_USB1_OTG_OC		0x40000090
+		>;
+	};
+
+	pinctrl_usdhc2_vcc_reg: usdhc2-vcc-reg-grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD2_RESET_B_GPIO2_IO19		0x4
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2-grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x190
+			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD			0x1d0
+			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d0
+			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d0
+			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d0
+			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d0
+			MX8MM_IOMUXC_SD2_WP_USDHC2_WP			0x400000d6
+			MX8MM_IOMUXC_SD2_CD_B_USDHC2_CD_B		0x0d6
+			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0x1d0
+		>;
+	};
+
+	pinctrl_usdhc2_100mhz: usdhc2-100mhz-grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x194
+			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD			0x1d4
+			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d4
+			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d4
+			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d4
+			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d4
+			MX8MM_IOMUXC_SD2_WP_USDHC2_WP			0x400000d6
+			MX8MM_IOMUXC_SD2_CD_B_USDHC2_CD_B		0x0d6
+			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0x1d0
+		>;
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2-200mhz-grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x196
+			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD			0x1d6
+			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d6
+			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d6
+			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d6
+			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d6
+			MX8MM_IOMUXC_SD2_WP_USDHC2_WP			0x400000d6
+			MX8MM_IOMUXC_SD2_CD_B_USDHC2_CD_B		0x0d6
+			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0x1d0
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3-grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK		0x190
+			MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD		0x1d0
+			MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0		0x1d0
+			MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1		0x1d0
+			MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2		0x1d0
+			MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3		0x1d0
+			MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4		0x1d0
+			MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5		0x1d0
+			MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6		0x1d0
+			MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7		0x1d0
+			MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE		0x190
+			MX8MM_IOMUXC_NAND_READY_B_SD3_RESET_B		0x40
+		>;
+	};
+
+	pinctrl_usdhc3_100mhz: usdhc3-100mhz-grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK		0x194
+			MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD		0x1d4
+			MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0		0x1d4
+			MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1		0x1d4
+			MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2		0x1d4
+			MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3		0x1d4
+			MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4		0x1d4
+			MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5		0x1d4
+			MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6		0x1d4
+			MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7		0x1d4
+			MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE		0x194
+			MX8MM_IOMUXC_NAND_READY_B_SD3_RESET_B		0x40
+		>;
+	};
+
+	pinctrl_usdhc3_200mhz: usdhc3-200mhz-grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK		0x196
+			MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD		0x1d6
+			MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0		0x1d6
+			MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1		0x1d6
+			MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2		0x1d6
+			MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3		0x1d6
+			MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4		0x1d6
+			MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5		0x1d6
+			MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6		0x1d6
+			MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7		0x1d6
+			MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE		0x196
+			MX8MM_IOMUXC_NAND_READY_B_SD3_RESET_B		0x40
+		>;
+	};
+
+	pinctrl_watchdog_gpio: watchdog-gpio-grp {
+		fsl,pins = <
+			/* WDOG_B# */
+			MX8MM_IOMUXC_GPIO1_IO02_GPIO1_IO2		0x26
+			/* WDOG_EN -- ungate WDT RESET# signal propagation */
+			MX8MM_IOMUXC_SD1_DATA7_GPIO2_IO9		0x6
+			/* WDOG_KICK# / WDI */
+			MX8MM_IOMUXC_GPIO1_IO08_GPIO1_IO8		0x26
+		>;
+	};
+};
+
+&pcie_phy {
+	fsl,clkreq-unsupported;	/* CLKREQ_B is not connected to suitable input */
+	fsl,refclk-pad-mode = <IMX8_PCIE_REFCLK_PAD_INPUT>;
+	fsl,tx-deemph-gen1 = <0x2d>;
+	fsl,tx-deemph-gen2 = <0xf>;
+	clocks = <&pcieclk 0>;
+	status = "okay";
+};
+
+&pcie0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pcie0>;
+	reset-gpio = <&gpio1 5 GPIO_ACTIVE_LOW>;
+	clocks = <&clk IMX8MM_CLK_PCIE1_ROOT>, <&clk IMX8MM_CLK_PCIE1_AUX>,
+		 <&pcieclk 0>;
+	clock-names = "pcie", "pcie_aux", "pcie_bus";
+	assigned-clocks = <&clk IMX8MM_CLK_PCIE1_AUX>,
+			  <&clk IMX8MM_CLK_PCIE1_CTRL>;
+	assigned-clock-rates = <10000000>, <250000000>;
+	assigned-clock-parents = <&clk IMX8MM_SYS_PLL2_50M>,
+				 <&clk IMX8MM_SYS_PLL2_250M>;
+	status = "okay";
+};
+
+&pwm1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_panel_pwm>;
+	/* Disabled by default, unless display board plugged in. */
+	status = "disabled";
+};
+
+&sai5 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sai5>;
+	fsl,sai-mclk-direction-output;
+	/* Input into codec PLL */
+	assigned-clocks = <&clk IMX8MM_CLK_SAI5>;
+	assigned-clock-parents = <&clk IMX8MM_AUDIO_PLL2_OUT>;
+	assigned-clock-rates = <22579200>;
+	/* Disabled by default, unless display board plugged in. */
+	status = "disabled";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	uart-has-rtscts;
+	status = "disabled";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	status = "disabled";
+};
+
+&uart3 {	/* A53 Debug */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	status = "okay";
+};
+
+&uart4 {	/* M4 Debug */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+	/* UART4 is reserved for CM and RDC blocks CA access to UART4. */
+	status = "disabled";
+};
+
+&usbotg1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb_otg1>;
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&usbotg2 {
+	disable-over-current;
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usdhc2 {	/* MicroSD */
+	assigned-clocks = <&clk IMX8MM_CLK_USDHC2_ROOT>;
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
+	bus-width = <4>;
+	vmmc-supply = <&reg_usdhc2_vcc>;
+	status = "okay";
+};
+
+&usdhc3 {	/* eMMC */
+	assigned-clocks = <&clk IMX8MM_CLK_USDHC3_ROOT>;
+	assigned-clock-rates = <400000000>;
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+	bus-width = <8>;
+	non-removable;
+	vmmc-supply = <&buck4_reg>;
+	vqmmc-supply = <&buck5_reg>;
+	status = "okay";
+};
+
+&wdog1 {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-emcon-avari.dts b/arch/arm64/boot/dts/freescale/imx8mm-emcon-avari.dts
new file mode 100644
index 000000000000..b2e8967e9687
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-emcon-avari.dts
@@ -0,0 +1,23 @@
+// SPDX-License-Identifier: (GPL-2.0 or MIT)
+//
+// Copyright (c) 2021 emtrion GmbH
+// Author: Frank Erdrich <frank.erdrich@emtrion.com>
+//
+
+/dts-v1/;
+
+#include "imx8mm-emcon.dtsi"
+#include "imx8mm-emcon-avari.dtsi"
+
+/ {
+	model = "emtrion SoM emCON-MX8M mini on Avari";
+	compatible = "emtrion,emcon-mx8mm-avari", "fsl,imx8mm";
+};
+
+&lvds_backlight {
+	status = "okay";
+};
+
+&pwm1 {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-emcon-avari.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-emcon-avari.dtsi
new file mode 100644
index 000000000000..5028f232b6bd
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-emcon-avari.dtsi
@@ -0,0 +1,139 @@
+// SPDX-License-Identifier: (GPL-2.0 or MIT)
+//
+// Copyright (C) 2021 emtrion GmbH
+// Author: Frank Erdrich <frank.erdrich@emtrion.com>
+//
+
+/ {
+	aliases {
+		boardid = &boardID;
+		mmc0 = &usdhc1;
+		mmc1 = &usdhc2;
+	};
+
+	chosen {
+		stdout-path = &uart1;
+	};
+
+	reg_wall_5p0: regulator-wall5p0 {
+		compatible = "regulator-fixed";
+		regulator-name = "Main-Supply";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	reg_base3p3: regulator-base3p3 {
+		compatible = "regulator-fixed";
+		vin-supply = <&reg_wall_5p0>;
+		regulator-name = "3V3-avari";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	reg_base1p5: regulator-base1p5 {
+		compatible = "regulator-fixed";
+		vin-supply = <&reg_base3p3>;
+		regulator-name = "1V5-avari";
+		regulator-min-microvolt = <1500000>;
+		regulator-max-microvolt = <1500000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	reg_usb_otg: regulator-otgvbus {
+		compatible = "regulator-fixed";
+		vin-supply = <&reg_wall_5p0>;
+		regulator-name = "OTG_VBUS";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio1 8 GPIO_ACTIVE_LOW>;
+		regulator-always-on;
+	};
+
+	clk_codec: clock-codec {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <12000000>;
+	};
+
+	sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "SGTL5000-Card";
+		simple-audio-card,format = "i2s";
+		simple-audio-card,bitclock-master = <&codec_dai>;
+		simple-audio-card,frame-master = <&codec_dai>;
+		simple-audio-card,widgets = "Headphone", "Headphone Jack";
+		simple-audio-card,routing = "Headphone Jack", "HP_OUT";
+
+		cpu_dai: simple-audio-card,cpu {
+			sound-dai = <&sai2>;
+		};
+
+		codec_dai: simple-audio-card,codec {
+			sound-dai = <&sgtl5000>;
+		};
+	};
+};
+
+&ecspi1 {
+	status = "okay";
+};
+
+&i2c2 {
+	status = "okay";
+};
+
+&i2c1 {
+	clock-frequency = <100000>;
+	status = "okay";
+
+	sgtl5000: audio-codec@a {
+		compatible = "fsl,sgtl5000";
+		reg = <0x0a>;
+		#sound-dai-cells = <0>;
+		clocks = <&clk_codec>;
+		VDDA-supply = <&reg_base3p3>;
+		VDDIO-supply = <&reg_base3p3>;
+	};
+
+	boardID: gpio@3a {
+		compatible = "nxp,pca8574";
+		reg = <0x3a>;
+		gpio-controller;
+		#gpio-cells = <1>;
+	};
+};
+
+&sai2 {
+	status = "okay";
+};
+
+&uart2 {
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&uart3 {
+	status = "okay";
+};
+
+&uart4 {
+	status = "okay";
+};
+
+&usbotg1 {
+	status = "okay";
+};
+
+&usbotg2 {
+	dr_mode = "host";
+	status = "disabled";
+};
+
+&usdhc2 {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-emcon.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-emcon.dtsi
new file mode 100644
index 000000000000..0dbdc9ec3fe5
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-emcon.dtsi
@@ -0,0 +1,627 @@
+// SPDX-License-Identifier: (GPL-2.0 or MIT)
+//
+// Copyright 2018 NXP
+// Copyright (C) 2021 emtrion GmbH
+//
+
+/dts-v1/;
+
+#include "imx8mm.dtsi"
+
+/ {
+	chosen {
+		stdout-path = &uart1;
+	};
+
+	som_leds: leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_led>;
+
+		green {
+			label = "som:green";
+			gpios = <&gpio3 4 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+			linux,default-trigger = "heartbeat";
+		};
+
+		red {
+			label = "som:red";
+			gpios = <&gpio5 10 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+	};
+
+	lvds_backlight: lvds-backlight {
+		compatible = "pwm-backlight";
+		enable-gpios = <&gpio3 23 GPIO_ACTIVE_HIGH>;
+		pwms = <&pwm1 0 50000 0>;
+		brightness-levels = <
+			0 4 8 16 32 64 80 96 112
+			128 144 160 176 250
+		>;
+		default-brightness-level = <9>;
+		status = "disabled";
+	};
+
+	reg_usdhc1_vmmc: regulator-emmc {
+		compatible = "regulator-fixed";
+		regulator-name = "eMMC";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	reg_usdhc2_vmmc: regulator-usdhc2 {
+		compatible = "regulator-fixed";
+		regulator-name = "sdcard_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+};
+
+&A53_0 {
+	cpu-supply = <&buck2_reg>;
+};
+
+&ecspi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1 &pinctrl_ecspi1_cs>;
+	cs-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>,
+				<&gpio5 13 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&fec1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_fec1>;
+	phy-mode = "rgmii-id";
+	phy-handle = <&ethphy0>;
+	fsl,magic-packet;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy0: ethernet-phy@0 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <0>;
+			reset-gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <10000>;
+		};
+	};
+};
+
+&flexspi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexspi0>;
+	pinctrl-1 = <&pinctrl_flexspi1>;
+	status = "okay";
+
+	flash0: flash@0 {
+		reg = <0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "jedec,spi-nor";
+		spi-max-frequency = <40000000>;
+	};
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+
+	pinctrl_csi_pwn: csi-pwn-grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO07_GPIO1_IO7		0x19
+		>;
+	};
+
+	pinctrl_ecspi1: ecspi1-grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_ECSPI1_SCLK_ECSPI1_SCLK		0x82
+			MX8MM_IOMUXC_ECSPI1_MOSI_ECSPI1_MOSI		0x82
+			MX8MM_IOMUXC_ECSPI1_MISO_ECSPI1_MISO		0x82
+		>;
+	};
+
+	pinctrl_ecspi1_cs: ecspi1-cs {
+		fsl,pins = <
+			MX8MM_IOMUXC_ECSPI1_SS0_GPIO5_IO9		0x40000
+			MX8MM_IOMUXC_ECSPI2_SS0_GPIO5_IO13		0x40000
+		>;
+	};
+
+	pinctrl_fec1: fec1-grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_ENET_MDC_ENET1_MDC				0x3
+			MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO			0x3
+			MX8MM_IOMUXC_ENET_TD3_ENET1_RGMII_TD3		0x1f
+			MX8MM_IOMUXC_ENET_TD2_ENET1_RGMII_TD2		0x1f
+			MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1		0x1f
+			MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0		0x1f
+			MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3		0x91
+			MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2		0x91
+			MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1		0x91
+			MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0		0x91
+			MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC		0x1f
+			MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC		0x91
+			MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL	0x91
+			MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL	0x1f
+			MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9			0x19
+		>;
+	};
+
+	pinctrl_flexspi0: flexspi0-grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_NAND_ALE_QSPI_A_SCLK		0x1c2
+			MX8MM_IOMUXC_NAND_CE0_B_QSPI_A_SS0_B	0x82
+			MX8MM_IOMUXC_NAND_DATA00_QSPI_A_DATA0	0x82
+			MX8MM_IOMUXC_NAND_DATA01_QSPI_A_DATA1	0x82
+			MX8MM_IOMUXC_NAND_DATA02_QSPI_A_DATA2	0x82
+			MX8MM_IOMUXC_NAND_DATA03_QSPI_A_DATA3	0x82
+			MX8MM_IOMUXC_NAND_DQS_QSPI_A_DQS		0x82
+		>;
+	};
+
+	pinctrl_flexspi1: flexspi1-grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_NAND_CLE_QSPI_B_SCLK		0x1c2
+			MX8MM_IOMUXC_NAND_CE2_B_QSPI_B_SS0_B	0x82
+			MX8MM_IOMUXC_NAND_DATA04_QSPI_B_DATA0	0x82
+			MX8MM_IOMUXC_NAND_DATA05_QSPI_B_DATA1	0x82
+			MX8MM_IOMUXC_NAND_DATA06_QSPI_B_DATA2	0x82
+			MX8MM_IOMUXC_NAND_DATA07_QSPI_B_DATA3	0x82
+		>;
+	};
+
+	pinctrl_gpio_led: gpio-led-grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_ECSPI2_SCLK_GPIO5_IO10		0x19
+			MX8MM_IOMUXC_NAND_CE3_B_GPIO3_IO4		0x19
+		>;
+	};
+
+	pinctrl_i2c1: i2c1-grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL			0x400001c3
+			MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA			0x400001c3
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_I2C2_SCL_I2C2_SCL			0x400001c3
+			MX8MM_IOMUXC_I2C2_SDA_I2C2_SDA			0x400001c3
+		>;
+	};
+
+	pinctrl_i2c3: i2c3-grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_I2C3_SCL_I2C3_SCL			0x400001c3
+			MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA			0x400001c3
+		>;
+	};
+
+	pinctrl_lvds: lvds-grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI5_MCLK_GPIO3_IO25		0x06
+		>;
+	};
+
+	pinctrl_pcie0: pcie0-grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI5_RXC_GPIO3_IO20		0x41
+			MX8MM_IOMUXC_SAI5_RXFS_GPIO3_IO19		0x41
+		>;
+	};
+
+	pinctrl_pmic: pmic-irq {
+		fsl,pins = <
+			MX8MM_IOMUXC_NAND_CE1_B_GPIO3_IO2		0x41
+		>;
+	};
+
+	pinctrl_pwm1: pwm1-grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO01_PWM1_OUT		0x06
+		>;
+	};
+
+	pinctrl_sai2: sai2-grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI2_MCLK_SAI2_MCLK		0xd6
+			MX8MM_IOMUXC_SAI2_RXC_SAI2_RX_BCLK		0xd6
+			MX8MM_IOMUXC_SAI2_RXD0_SAI2_RX_DATA0	0xd6
+			MX8MM_IOMUXC_SAI2_RXFS_SAI2_RX_SYNC		0xd6
+			MX8MM_IOMUXC_SAI2_TXC_SAI2_TX_BCLK		0xd6
+			MX8MM_IOMUXC_SAI2_TXD0_SAI2_TX_DATA0	0xd6
+			MX8MM_IOMUXC_SAI2_TXFS_SAI2_TX_SYNC		0xd6
+		>;
+	};
+
+	pinctrl_spdif1: spdif1-grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SPDIF_TX_SPDIF1_OUT		0xd6
+			MX8MM_IOMUXC_SPDIF_RX_SPDIF1_IN			0xd6
+		>;
+	};
+
+	pinctrl_uart1: uart1-grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_UART1_RXD_UART1_DCE_RX		0x140
+			MX8MM_IOMUXC_UART1_TXD_UART1_DCE_TX		0x140
+		>;
+	};
+
+	pinctrl_uart2: uart2-grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_UART2_RXD_UART2_DCE_RX		0x140
+			MX8MM_IOMUXC_UART2_TXD_UART2_DCE_TX		0x140
+
+			/* rts and cts */
+			MX8MM_IOMUXC_SAI3_RXC_UART2_DCE_CTS_B	0x140
+			MX8MM_IOMUXC_SAI3_RXD_UART2_DCE_RTS_B	0x140
+		>;
+	};
+
+	pinctrl_uart3: uart3-grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_UART3_RXD_UART3_DCE_RX		0x140
+			MX8MM_IOMUXC_UART3_TXD_UART3_DCE_TX		0x140
+		>;
+	};
+
+	pinctrl_uart4: uart4-grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_UART4_RXD_UART4_DCE_RX		0x140
+			MX8MM_IOMUXC_UART4_TXD_UART4_DCE_TX		0x140
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1-grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK			0x190
+			MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD			0x1d0
+			MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0		0x1d0
+			MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1		0x1d0
+			MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2		0x1d0
+			MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3		0x1d0
+			MX8MM_IOMUXC_SD1_DATA4_USDHC1_DATA4		0x1d0
+			MX8MM_IOMUXC_SD1_DATA5_USDHC1_DATA5		0x1d0
+			MX8MM_IOMUXC_SD1_DATA6_USDHC1_DATA6		0x1d0
+			MX8MM_IOMUXC_SD1_DATA7_USDHC1_DATA7		0x1d0
+		>;
+	};
+
+	pinctrl_usdhc1_100mhz: usdhc1-100mhz-grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK			0x194
+			MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD			0x1d4
+			MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0		0x1d4
+			MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1		0x1d4
+			MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2		0x1d4
+			MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3		0x1d4
+			MX8MM_IOMUXC_SD1_DATA4_USDHC1_DATA4		0x1d4
+			MX8MM_IOMUXC_SD1_DATA5_USDHC1_DATA5		0x1d4
+			MX8MM_IOMUXC_SD1_DATA6_USDHC1_DATA6		0x1d4
+			MX8MM_IOMUXC_SD1_DATA7_USDHC1_DATA7		0x1d4
+		>;
+	};
+
+	pinctrl_usdhc1_200mhz: usdhc1-200mhz-grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK			0x196
+			MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD			0x1d6
+			MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0		0x1d6
+			MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1		0x1d6
+			MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2		0x1d6
+			MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3		0x1d6
+			MX8MM_IOMUXC_SD1_DATA4_USDHC1_DATA4		0x1d6
+			MX8MM_IOMUXC_SD1_DATA5_USDHC1_DATA5		0x1d6
+			MX8MM_IOMUXC_SD1_DATA6_USDHC1_DATA6		0x1d6
+			MX8MM_IOMUXC_SD1_DATA7_USDHC1_DATA7		0x1d6
+		>;
+	};
+
+	pinctrl_usdhc1_gpio: usdhc1-gpio-grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD1_RESET_B_USDHC1_RESET_B	0x41
+			MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3		0x1c4
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2-grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x190
+			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD			0x1d0
+			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d0
+			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d0
+			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d0
+			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d0
+			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT	0x1d0
+		>;
+	};
+
+	pinctrl_usdhc2_100mhz: usdhc2-100mhz-grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x194
+			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD			0x1d4
+			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d4
+			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d4
+			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d4
+			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d4
+			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT	0x1d0
+		>;
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2-200mhz-grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x196
+			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD			0x1d6
+			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d6
+			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d6
+			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d6
+			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d6
+			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT	0x1d0
+		>;
+	};
+
+	/* no reset for sdhc2 interface */
+	pinctrl_usdhc2_gpio: usdhc2-gpio-grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x1c4
+			MX8MM_IOMUXC_SD2_WP_USDHC2_WP			0x1c4
+		>;
+	};
+
+	pinctrl_wdog: wdog-grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B	0xc6
+		>;
+	};
+};
+
+&i2c1 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+};
+
+&i2c2 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	status = "okay";
+};
+
+&i2c3 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "okay";
+
+	bd71847: pmic@4b {
+		compatible = "rohm,bd71847";
+		reg = <0x4b>;
+		pinctrl-0 = <&pinctrl_pmic>;
+		interrupt-parent = <&gpio3>;
+		interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
+		rohm,reset-snvs-powered;
+
+		regulators {
+			buck1_reg: BUCK1 {
+				regulator-name = "BUCK1";
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <1300000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <1250>;
+			};
+
+			buck2_reg: BUCK2 {
+				regulator-name = "BUCK2";
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <1300000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <1250>;
+				rohm,dvs-run-voltage = <1000000>;
+				rohm,dvs-idle-voltage = <900000>;
+			};
+
+			buck3_reg: BUCK3 {
+				// BUCK5 in datasheet
+				regulator-name = "BUCK3";
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			buck4_reg: BUCK4 {
+				// BUCK6 in datasheet
+				regulator-name = "BUCK4";
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			buck5_reg: BUCK5 {
+				// BUCK7 in datasheet
+				regulator-name = "BUCK5";
+				regulator-min-microvolt = <1605000>;
+				regulator-max-microvolt = <1995000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			buck6_reg: BUCK6 {
+				// BUCK8 in datasheet
+				regulator-name = "BUCK6";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1400000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo1_reg: LDO1 {
+				regulator-name = "LDO1";
+				regulator-min-microvolt = <1600000>;
+				regulator-max-microvolt = <1900000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo2_reg: LDO2 {
+				regulator-name = "LDO2";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <900000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo3_reg: LDO3 {
+				regulator-name = "LDO3";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo4_reg: LDO4 {
+				regulator-name = "LDO4";
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo6_reg: LDO6 {
+				regulator-name = "LDO6";
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+		};
+	};
+
+	rv1805: rtc@69 {
+		compatible = "abracon,ab1805";
+		reg = <0x69>;
+	};
+};
+
+&mu {
+	status = "okay";
+};
+
+&pwm1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm1>;
+};
+
+&sai2 {
+	#sound-dai-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sai2>;
+	assigned-clocks = <&clk IMX8MM_CLK_SAI2>;
+	assigned-clock-parents = <&clk IMX8MM_AUDIO_PLL1_OUT>;
+	assigned-clock-rates = <12000000>;
+	status = "disabled";
+};
+
+&spdif1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_spdif1>;
+	assigned-clocks = <&clk IMX8MM_CLK_SPDIF1>;
+	assigned-clock-parents = <&clk IMX8MM_AUDIO_PLL1_OUT>;
+	assigned-clock-rates = <24576000>;
+	clocks = <&clk IMX8MM_CLK_AUDIO_AHB>, <&clk IMX8MM_CLK_24M>,
+		<&clk IMX8MM_CLK_SPDIF1>, <&clk IMX8MM_CLK_DUMMY>,
+		<&clk IMX8MM_CLK_DUMMY>, <&clk IMX8MM_CLK_DUMMY>,
+		<&clk IMX8MM_CLK_AUDIO_AHB>, <&clk IMX8MM_CLK_DUMMY>,
+		<&clk IMX8MM_CLK_DUMMY>, <&clk IMX8MM_CLK_DUMMY>,
+		<&clk IMX8MM_AUDIO_PLL1_OUT>, <&clk IMX8MM_AUDIO_PLL2_OUT>;
+	clock-names = "core", "rxtx0", "rxtx1", "rxtx2", "rxtx3",
+		"rxtx4", "rxtx5", "rxtx6", "rxtx7", "spba", "pll8k", "pll11k";
+	status = "disabled";
+};
+
+&uart1 { /* console */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	assigned-clocks = <&clk IMX8MM_CLK_UART1>;
+	assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_80M>;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	assigned-clocks = <&clk IMX8MM_CLK_UART2>;
+	assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_80M>;
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	assigned-clocks = <&clk IMX8MM_CLK_UART3>;
+	assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_80M>;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+	assigned-clocks = <&clk IMX8MM_CLK_UART4>;
+	assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_80M>;
+	status = "okay";
+};
+
+&usbotg1 {
+	dr_mode = "otg";
+	over-current-active-low;
+	status = "okay";
+};
+
+&usbotg2 {
+	dr_mode = "host";
+	disable-over-current;
+	status = "disabled";
+};
+
+&usdhc1 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc1>, <&pinctrl_usdhc1_gpio>;
+	pinctrl-1 = <&pinctrl_usdhc1_100mhz>, <&pinctrl_usdhc1_gpio>;
+	pinctrl-2 = <&pinctrl_usdhc1_200mhz>, <&pinctrl_usdhc1_gpio>;
+	bus-width = <8>;
+	vmmc-supply = <&reg_usdhc1_vmmc>;
+	keep-power-in-suspend;
+	non-removable;
+	status = "okay";
+};
+
+&usdhc2 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
+	cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio2 20 GPIO_ACTIVE_HIGH>;
+	bus-width = <4>;
+	vmmc-supply = <&reg_usdhc2_vmmc>;
+	no-1-8-v;
+	status = "okay";
+};
+
+&wdog1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog>;
+	fsl,ext-reset-output;
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-evk.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-evk.dtsi
index e033d0257b5a..7d6317d95b13 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-evk.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm-evk.dtsi
@@ -5,6 +5,7 @@
 
 /dts-v1/;
 
+#include <dt-bindings/phy/phy-imx8-pcie.h>
 #include <dt-bindings/usb/pd.h>
 #include "imx8mm.dtsi"
 
@@ -30,6 +31,23 @@
 		};
 	};
 
+	pcie0_refclk: pcie0-refclk {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <100000000>;
+	};
+
+	reg_pcie0: regulator-pcie {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_pcie0_reg>;
+		regulator-name = "MPCIE_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio1 5 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
 	reg_usdhc2_vmmc: regulator-usdhc2 {
 		compatible = "regulator-fixed";
 		pinctrl-names = "default";
@@ -41,6 +59,14 @@
 		enable-active-high;
 	};
 
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm1 0 5000000 0>;
+		brightness-levels = <0 255>;
+		num-interpolated-steps = <255>;
+		default-brightness-level = <250>;
+	};
+
 	ir-receiver {
 		compatible = "gpio-ir-receiver";
 		gpios = <&gpio1 13 GPIO_ACTIVE_LOW>;
@@ -49,6 +75,11 @@
 		linux,autosuspend-period = <125>;
 	};
 
+	audio_codec_bt_sco: audio-codec-bt-sco {
+		compatible = "linux,bt-sco";
+		#sound-dai-cells = <1>;
+	};
+
 	wm8524: audio-codec {
 		#sound-dai-cells = <0>;
 		compatible = "wlf,wm8524";
@@ -57,6 +88,25 @@
 		wlf,mute-gpios = <&gpio5 21 GPIO_ACTIVE_LOW>;
 	};
 
+	sound-bt-sco {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "bt-sco-audio";
+		simple-audio-card,format = "dsp_a";
+		simple-audio-card,bitclock-inversion;
+		simple-audio-card,frame-master = <&btcpu>;
+		simple-audio-card,bitclock-master = <&btcpu>;
+
+		btcpu: simple-audio-card,cpu {
+			sound-dai = <&sai2>;
+			dai-tdm-slot-num = <2>;
+			dai-tdm-slot-width = <16>;
+		};
+
+		simple-audio-card,codec {
+			sound-dai = <&audio_codec_bt_sco 1>;
+		};
+	};
+
 	sound-wm8524 {
 		compatible = "simple-audio-card";
 		simple-audio-card,name = "wm8524-audio";
@@ -116,6 +166,13 @@
 			reg = <0>;
 			reset-gpios = <&gpio4 22 GPIO_ACTIVE_LOW>;
 			reset-assert-us = <10000>;
+			qca,disable-smarteee;
+			vddio-supply = <&vddio>;
+
+			vddio: vddio-regulator {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
 		};
 	};
 };
@@ -289,6 +346,40 @@
 	};
 };
 
+&pcie_phy {
+	fsl,refclk-pad-mode = <IMX8_PCIE_REFCLK_PAD_INPUT>;
+	fsl,tx-deemph-gen1 = <0x2d>;
+	fsl,tx-deemph-gen2 = <0xf>;
+	clocks = <&pcie0_refclk>;
+	status = "okay";
+};
+
+&pcie0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pcie0>;
+	reset-gpio = <&gpio4 21 GPIO_ACTIVE_LOW>;
+	clocks = <&clk IMX8MM_CLK_PCIE1_ROOT>, <&clk IMX8MM_CLK_PCIE1_AUX>,
+		 <&pcie0_refclk>;
+	clock-names = "pcie", "pcie_aux", "pcie_bus";
+	assigned-clocks = <&clk IMX8MM_CLK_PCIE1_AUX>,
+			  <&clk IMX8MM_CLK_PCIE1_CTRL>;
+	assigned-clock-rates = <10000000>, <250000000>;
+	assigned-clock-parents = <&clk IMX8MM_SYS_PLL2_50M>,
+				 <&clk IMX8MM_SYS_PLL2_250M>;
+	vpcie-supply = <&reg_pcie0>;
+	status = "okay";
+};
+
+&sai2 {
+	#sound-dai-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sai2>;
+	assigned-clocks = <&clk IMX8MM_CLK_SAI2>;
+	assigned-clock-parents = <&clk IMX8MM_AUDIO_PLL1_OUT>;
+	assigned-clock-rates = <24576000>;
+	status = "okay";
+};
+
 &sai3 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_sai3>;
@@ -346,6 +437,12 @@
 	status = "okay";
 };
 
+&pwm1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_backlight>;
+	status = "okay";
+};
+
 &iomuxc {
 	pinctrl_fec1: fec1grp {
 		fsl,pins = <
@@ -406,6 +503,19 @@
 		>;
 	};
 
+	pinctrl_pcie0: pcie0grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_I2C4_SCL_PCIE1_CLKREQ_B    0x61
+			MX8MM_IOMUXC_SAI2_RXFS_GPIO4_IO21       0x41
+		>;
+	};
+
+	pinctrl_pcie0_reg: pcie0reggrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO05_GPIO1_IO5       0x41
+		>;
+	};
+
 	pinctrl_pmic: pmicirqgrp {
 		fsl,pins = <
 			MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3		0x141
@@ -418,6 +528,15 @@
 		>;
 	};
 
+	pinctrl_sai2: sai2grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI2_TXC_SAI2_TX_BCLK      0xd6
+			MX8MM_IOMUXC_SAI2_TXFS_SAI2_TX_SYNC     0xd6
+			MX8MM_IOMUXC_SAI2_TXD0_SAI2_TX_DATA0    0xd6
+			MX8MM_IOMUXC_SAI2_RXD0_SAI2_RX_DATA0    0xd6
+		>;
+	};
+
 	pinctrl_sai3: sai3grp {
 		fsl,pins = <
 			MX8MM_IOMUXC_SAI3_TXFS_SAI3_TX_SYNC     0xd6
@@ -487,4 +606,10 @@
 			MX8MM_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B	0x166
 		>;
 	};
+
+	pinctrl_backlight: backlightgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO01_PWM1_OUT	0x06
+		>;
+	};
 };
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-icore-mx8mm-ctouch2.dts b/arch/arm64/boot/dts/freescale/imx8mm-icore-mx8mm-ctouch2.dts
index 5389d6f2beba..502745402847 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-icore-mx8mm-ctouch2.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mm-icore-mx8mm-ctouch2.dts
@@ -91,7 +91,6 @@
 	max-frequency = <50000000>;
 	bus-width = <4>;
 	no-1-8-v;
-	pm-ignore-notify;
 	keep-power-in-suspend;
 	status = "okay";
 };
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-icore-mx8mm-edimm2.2.dts b/arch/arm64/boot/dts/freescale/imx8mm-icore-mx8mm-edimm2.2.dts
index a4a2ada14835..ddac8bc7ae65 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-icore-mx8mm-edimm2.2.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mm-icore-mx8mm-edimm2.2.dts
@@ -91,7 +91,6 @@
 	max-frequency = <50000000>;
 	bus-width = <4>;
 	no-1-8-v;
-	pm-ignore-notify;
 	keep-power-in-suspend;
 	status = "okay";
 };
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-icore-mx8mm.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-icore-mx8mm.dtsi
index b40148d728ea..def7bb5d37cf 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-icore-mx8mm.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm-icore-mx8mm.dtsi
@@ -2,7 +2,7 @@
 /*
  * Copyright (c) 2018 NXP
  * Copyright (c) 2019 Engicam srl
- * Copyright (c) 2020 Amarula Solutons(India)
+ * Copyright (c) 2020 Amarula Solutions(India)
  */
 
 / {
@@ -84,42 +84,42 @@
 			};
 
 			reg_buck1: buck1 {
-				regulator-min-microvolt =  <400000>;
+				regulator-min-microvolt = <400000>;
 				regulator-max-microvolt = <1800000>;
 				regulator-always-on;
 				regulator-boot-on;
 			};
 
 			reg_buck2: buck2 {
-				regulator-min-microvolt =  <400000>;
+				regulator-min-microvolt = <400000>;
 				regulator-max-microvolt = <1800000>;
 				regulator-always-on;
 				regulator-boot-on;
 			};
 
 			reg_buck3: buck3 {
-				regulator-min-microvolt =  <400000>;
+				regulator-min-microvolt = <400000>;
 				regulator-max-microvolt = <1800000>;
 				regulator-always-on;
 				regulator-boot-on;
 			};
 
 			reg_buck4: buck4 {
-				regulator-min-microvolt =  <400000>;
+				regulator-min-microvolt = <400000>;
 				regulator-max-microvolt = <1800000>;
 				regulator-always-on;
 				regulator-boot-on;
 			};
 
 			reg_buck5: buck5 {
-				regulator-min-microvolt =  <400000>;
+				regulator-min-microvolt = <400000>;
 				regulator-max-microvolt = <1800000>;
 				regulator-always-on;
 				regulator-boot-on;
 			};
 
 			reg_buck6: buck6 {
-				regulator-min-microvolt =  <400000>;
+				regulator-min-microvolt = <400000>;
 				regulator-max-microvolt = <1800000>;
 				regulator-always-on;
 				regulator-boot-on;
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts
new file mode 100644
index 000000000000..8b16bd68576c
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl-osm-s.dts
@@ -0,0 +1,376 @@
+// SPDX-License-Identifier: GPL-2.0+ OR MIT
+/*
+ * Copyright (C) 2022 Kontron Electronics GmbH
+ */
+
+/dts-v1/;
+
+#include "imx8mm-kontron-osm-s.dtsi"
+
+/ {
+	model = "Kontron BL i.MX8MM OSM-S (N802X S)";
+	compatible = "kontron,imx8mm-bl-osm-s", "kontron,imx8mm-osm-s", "fsl,imx8mm";
+
+	aliases {
+		ethernet1 = &usbnet;
+	};
+
+	/* fixed crystal dedicated to mcp2542fd */
+	osc_can: clock-osc-can {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <40000000>;
+		clock-output-names = "osc-can";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_led>;
+
+		led1 {
+			label = "led1";
+			gpios = <&gpio1 12 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "heartbeat";
+		};
+
+		led2 {
+			label = "led2";
+			gpios = <&gpio1 13 GPIO_ACTIVE_LOW>;
+		};
+
+		led3 {
+			label = "led3";
+			gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	pwm-beeper {
+		compatible = "pwm-beeper";
+		pwms = <&pwm2 0 5000 0>;
+	};
+
+	reg_rst_eth2: regulator-rst-eth2 {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usb_eth2>;
+		gpio = <&gpio3 2 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-always-on;
+		regulator-name = "rst-usb-eth2";
+	};
+
+	reg_usb1_vbus: regulator-usb1-vbus {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_usb1_vbus>;
+		gpio = <&gpio3 25 GPIO_ACTIVE_LOW>;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-name = "usb1-vbus";
+	};
+
+	reg_vdd_5v: regulator-5v {
+		compatible = "regulator-fixed";
+		regulator-always-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-name = "vdd-5v";
+	};
+};
+
+&ecspi2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi2>;
+	cs-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>;
+	status = "okay";
+
+	can@0 {
+		compatible = "microchip,mcp251xfd";
+		reg = <0>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_can>;
+		clocks = <&osc_can>;
+		interrupts-extended = <&gpio4 28 IRQ_TYPE_LEVEL_LOW>;
+		/*
+		 * Limit the SPI clock to 15 MHz to prevent issues
+		 * with corrupted data due to chip errata.
+		 */
+		spi-max-frequency = <15000000>;
+		vdd-supply = <&reg_vdd_3v3>;
+		xceiver-supply = <&reg_vdd_5v>;
+	};
+};
+
+&ecspi3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi3>;
+	cs-gpios = <&gpio5 25 GPIO_ACTIVE_LOW>;
+	status = "okay";
+
+	eeram@0 {
+		compatible = "microchip,48l640";
+		reg = <0>;
+		spi-max-frequency = <20000000>;
+	};
+};
+
+&fec1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet>;
+	phy-connection-type = "rgmii-rxid";
+	phy-handle = <&ethphy>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy: ethernet-phy@0 {
+			reg = <0>;
+			reset-assert-us = <1>;
+			reset-deassert-us = <15000>;
+			reset-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&gpio1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpio1>;
+	gpio-line-names = "", "", "", "dio1-out", "", "", "dio1-in", "dio2-out",
+			  "dio2-in", "dio3-out", "dio3-in", "dio4-out", "", "", "", "",
+			  "", "", "", "", "", "", "", "",
+			  "", "", "", "", "", "", "", "";
+};
+
+&gpio5 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpio5>;
+	gpio-line-names = "", "", "dio4-in", "", "", "", "", "",
+			  "", "", "", "", "", "", "", "",
+			  "", "", "", "", "", "", "", "",
+			  "", "", "", "", "", "", "", "";
+};
+
+&i2c4 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c4>;
+	status = "okay";
+};
+
+&pwm2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm2>;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	linux,rs485-enabled-at-boot-time;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&usbotg1 {
+	dr_mode = "otg";
+	disable-over-current;
+	vbus-supply = <&reg_usb1_vbus>;
+	status = "okay";
+};
+
+&usbotg2 {
+	dr_mode = "host";
+	disable-over-current;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	usb1@1 {
+		compatible = "usb424,9514";
+		reg = <1>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		usbnet: ethernet@1 {
+			compatible = "usb424,ec00";
+			reg = <1>;
+			local-mac-address = [ 00 00 00 00 00 00 ];
+		};
+	};
+};
+
+&usdhc2 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
+	vmmc-supply = <&reg_vdd_3v3>;
+	vqmmc-supply = <&reg_nvcc_sd>;
+	cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_can: cangrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI3_RXFS_GPIO4_IO28		0x19
+		>;
+	};
+
+	pinctrl_ecspi2: ecspi2grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_ECSPI2_MISO_ECSPI2_MISO		0x82
+			MX8MM_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI		0x82
+			MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK		0x82
+			MX8MM_IOMUXC_ECSPI2_SS0_GPIO5_IO13		0x19
+		>;
+	};
+
+	pinctrl_ecspi3: ecspi3grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_UART2_RXD_ECSPI3_MISO		0x82
+			MX8MM_IOMUXC_UART1_TXD_ECSPI3_MOSI		0x82
+			MX8MM_IOMUXC_UART1_RXD_ECSPI3_SCLK		0x82
+			MX8MM_IOMUXC_UART2_TXD_GPIO5_IO25		0x19
+		>;
+	};
+
+	pinctrl_enet: enetgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_ENET_MDC_ENET1_MDC			0x3
+			MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO		0x3
+			MX8MM_IOMUXC_ENET_TD3_ENET1_RGMII_TD3		0x1f
+			MX8MM_IOMUXC_ENET_TD2_ENET1_RGMII_TD2		0x1f
+			MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1		0x1f
+			MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0		0x1f
+			MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3		0x91
+			MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2		0x91
+			MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1		0x91
+			MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0		0x91
+			MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC		0x1f
+			MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC		0x91
+			MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL	0x91
+			MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL	0x1f
+			MX8MM_IOMUXC_GPIO1_IO01_GPIO1_IO1		0x19 /* PHY RST */
+			MX8MM_IOMUXC_GPIO1_IO05_GPIO1_IO5		0x19 /* ETH IRQ */
+		>;
+	};
+
+	pinctrl_gpio_led: gpioledgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO12_GPIO1_IO12		0x19
+			MX8MM_IOMUXC_GPIO1_IO13_GPIO1_IO13		0x19
+			MX8MM_IOMUXC_GPIO1_IO14_GPIO1_IO14		0x19
+		>;
+	};
+
+	pinctrl_gpio1: gpio1grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3		0x19
+			MX8MM_IOMUXC_GPIO1_IO07_GPIO1_IO7		0x19
+			MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9		0x19
+			MX8MM_IOMUXC_GPIO1_IO11_GPIO1_IO11		0x19
+			MX8MM_IOMUXC_GPIO1_IO06_GPIO1_IO6		0x19
+			MX8MM_IOMUXC_GPIO1_IO08_GPIO1_IO8		0x19
+			MX8MM_IOMUXC_GPIO1_IO10_GPIO1_IO10		0x19
+		>;
+	};
+
+	pinctrl_gpio5: gpio5grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI3_MCLK_GPIO5_IO2		0x19
+		>;
+	};
+
+	pinctrl_i2c4: i2c4grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_I2C4_SCL_I2C4_SCL			0x400001c3
+			MX8MM_IOMUXC_I2C4_SDA_I2C4_SDA			0x400001c3
+		>;
+	};
+
+	pinctrl_pwm2: pwm2grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SPDIF_RX_PWM2_OUT			0x19
+		>;
+	};
+
+	pinctrl_reg_usb1_vbus: regusb1vbusgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI5_MCLK_GPIO3_IO25		0x19
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI2_RXC_UART1_DCE_RX		0x140
+			MX8MM_IOMUXC_SAI2_RXFS_UART1_DCE_TX		0x140
+			MX8MM_IOMUXC_SAI2_RXD0_UART1_DCE_RTS_B		0x140
+			MX8MM_IOMUXC_SAI2_TXFS_UART1_DCE_CTS_B		0x140
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI3_TXFS_UART2_DCE_RX		0x140
+			MX8MM_IOMUXC_SAI3_TXC_UART2_DCE_TX		0x140
+			MX8MM_IOMUXC_SAI3_RXD_UART2_DCE_RTS_B		0x140
+			MX8MM_IOMUXC_SAI3_RXC_UART2_DCE_CTS_B		0x140
+		>;
+	};
+
+	pinctrl_usb_eth2: usbeth2grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_NAND_CE1_B_GPIO3_IO2		0x19
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x190
+			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD			0x1d0
+			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d0
+			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d0
+			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d0
+			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d0
+			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x019
+			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0x1d0
+		>;
+	};
+
+	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x194
+			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD			0x1d4
+			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d4
+			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d4
+			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d4
+			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d4
+			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x019
+			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0x1d0
+		>;
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x196
+			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD			0x1d6
+			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d6
+			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d6
+			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d6
+			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d6
+			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x019
+			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0x1d0
+		>;
+	};
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl.dts
new file mode 100644
index 000000000000..a079322a3793
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-bl.dts
@@ -0,0 +1,353 @@
+// SPDX-License-Identifier: GPL-2.0+ OR MIT
+/*
+ * Copyright (C) 2019 Kontron Electronics GmbH
+ */
+
+/dts-v1/;
+
+#include "imx8mm-kontron-sl.dtsi"
+
+/ {
+	model = "Kontron BL i.MX8MM (N801X S)";
+	compatible = "kontron,imx8mm-bl", "kontron,imx8mm-sl", "fsl,imx8mm";
+
+	aliases {
+		ethernet1 = &usbnet;
+	};
+
+	/* fixed crystal dedicated to mcp2515 */
+	osc_can: clock-osc-can {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <16000000>;
+		clock-output-names = "osc-can";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_led>;
+
+		led1 {
+			label = "led1";
+			gpios = <&gpio4 17 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "heartbeat";
+		};
+
+		led2 {
+			label = "led2";
+			gpios = <&gpio4 19 GPIO_ACTIVE_LOW>;
+		};
+
+		led3 {
+			label = "led3";
+			gpios = <&gpio4 18 GPIO_ACTIVE_LOW>;
+		};
+
+		led4 {
+			label = "led4";
+			gpios = <&gpio4 8 GPIO_ACTIVE_LOW>;
+		};
+
+		led5 {
+			label = "led5";
+			gpios = <&gpio4 9 GPIO_ACTIVE_LOW>;
+		};
+
+		led6 {
+			label = "led6";
+			gpios = <&gpio4 7 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	pwm-beeper {
+		compatible = "pwm-beeper";
+		pwms = <&pwm2 0 5000 0>;
+	};
+
+	reg_rst_eth2: regulator-rst-eth2 {
+		compatible = "regulator-fixed";
+		regulator-name = "rst-usb-eth2";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usb_eth2>;
+		gpio = <&gpio3 2 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-always-on;
+	};
+
+	reg_vdd_5v: regulator-5v {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd-5v";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+};
+
+&ecspi2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi2>;
+	cs-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>;
+	status = "okay";
+
+	can0: can@0 {
+		compatible = "microchip,mcp2515";
+		reg = <0>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_can>;
+		clocks = <&osc_can>;
+		interrupt-parent = <&gpio4>;
+		interrupts = <28 IRQ_TYPE_EDGE_FALLING>;
+		spi-max-frequency = <10000000>;
+		vdd-supply = <&reg_vdd_3v3>;
+		xceiver-supply = <&reg_vdd_5v>;
+	};
+};
+
+&ecspi3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi3>;
+	cs-gpios = <&gpio5 25 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&fec1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet>;
+	phy-connection-type = "rgmii-rxid";
+	phy-handle = <&ethphy>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy: ethernet-phy@0 {
+			reg = <0>;
+			reset-assert-us = <1>;
+			reset-deassert-us = <15000>;
+			reset-gpios = <&gpio4 27 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&i2c4 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c4>;
+	status = "okay";
+
+	rtc@32 {
+		compatible = "epson,rx8900";
+		reg = <0x32>;
+	};
+};
+
+&pwm2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm2>;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	linux,rs485-enabled-at-boot-time;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&usbotg1 {
+	dr_mode = "otg";
+	over-current-active-low;
+	status = "okay";
+};
+
+&usbotg2 {
+	dr_mode = "host";
+	disable-over-current;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	usb1@1 {
+		compatible = "usb424,9514";
+		reg = <1>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		usbnet: ethernet@1 {
+			compatible = "usb424,ec00";
+			reg = <1>;
+			local-mac-address = [ 00 00 00 00 00 00 ];
+		};
+	};
+};
+
+&usdhc2 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
+	vmmc-supply = <&reg_vdd_3v3>;
+	vqmmc-supply = <&reg_nvcc_sd>;
+	cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpio>;
+
+	pinctrl_can: cangrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI3_RXFS_GPIO4_IO28		0x19
+		>;
+	};
+
+	pinctrl_ecspi2: ecspi2grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_ECSPI2_MISO_ECSPI2_MISO		0x82
+			MX8MM_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI		0x82
+			MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK		0x82
+			MX8MM_IOMUXC_ECSPI2_SS0_GPIO5_IO13		0x19
+		>;
+	};
+
+	pinctrl_ecspi3: ecspi3grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_UART2_RXD_ECSPI3_MISO		0x82
+			MX8MM_IOMUXC_UART1_TXD_ECSPI3_MOSI		0x82
+			MX8MM_IOMUXC_UART1_RXD_ECSPI3_SCLK		0x82
+			MX8MM_IOMUXC_UART2_TXD_GPIO5_IO25		0x19
+		>;
+	};
+
+	pinctrl_enet: enetgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_ENET_MDC_ENET1_MDC			0x3
+			MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO		0x3
+			MX8MM_IOMUXC_ENET_TD3_ENET1_RGMII_TD3		0x1f
+			MX8MM_IOMUXC_ENET_TD2_ENET1_RGMII_TD2		0x1f
+			MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1		0x1f
+			MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0		0x1f
+			MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3		0x91
+			MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2		0x91
+			MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1		0x91
+			MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0		0x91
+			MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC		0x1f
+			MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC		0x91
+			MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL	0x91
+			MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL	0x1f
+			MX8MM_IOMUXC_SAI2_MCLK_GPIO4_IO27		0x19 /* PHY RST */
+			MX8MM_IOMUXC_SAI2_TXC_GPIO4_IO25		0x19 /* ETH IRQ */
+		>;
+	};
+
+	pinctrl_gpio_led: gpioledgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_NAND_READY_B_GPIO3_IO16		0x19
+			MX8MM_IOMUXC_SAI1_RXD5_GPIO4_IO7		0x19
+			MX8MM_IOMUXC_SAI1_RXD6_GPIO4_IO8		0x19
+			MX8MM_IOMUXC_SAI1_RXD7_GPIO4_IO9		0x19
+			MX8MM_IOMUXC_SAI1_TXD5_GPIO4_IO17		0x19
+			MX8MM_IOMUXC_SAI1_TXD6_GPIO4_IO18		0x19
+			MX8MM_IOMUXC_SAI1_TXD7_GPIO4_IO19		0x19
+		>;
+	};
+
+	pinctrl_gpio: gpiogrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3		0x19
+			MX8MM_IOMUXC_GPIO1_IO07_GPIO1_IO7		0x19
+			MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9		0x19
+			MX8MM_IOMUXC_GPIO1_IO11_GPIO1_IO11		0x19
+			MX8MM_IOMUXC_GPIO1_IO06_GPIO1_IO6		0x19
+			MX8MM_IOMUXC_GPIO1_IO08_GPIO1_IO8		0x19
+			MX8MM_IOMUXC_GPIO1_IO10_GPIO1_IO10		0x19
+			MX8MM_IOMUXC_SAI3_MCLK_GPIO5_IO2		0x19
+		>;
+	};
+
+	pinctrl_i2c4: i2c4grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_I2C4_SCL_I2C4_SCL			0x400001c3
+			MX8MM_IOMUXC_I2C4_SDA_I2C4_SDA			0x400001c3
+		>;
+	};
+
+	pinctrl_pwm2: pwm2grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SPDIF_RX_PWM2_OUT			0x19
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI2_RXC_UART1_DCE_RX		0x140
+			MX8MM_IOMUXC_SAI2_RXFS_UART1_DCE_TX		0x140
+			MX8MM_IOMUXC_SAI2_RXD0_UART1_DCE_RTS_B		0x140
+			MX8MM_IOMUXC_SAI2_TXFS_UART1_DCE_CTS_B		0x140
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI3_TXFS_UART2_DCE_RX		0x140
+			MX8MM_IOMUXC_SAI3_TXC_UART2_DCE_TX		0x140
+			MX8MM_IOMUXC_SAI3_RXD_UART2_DCE_RTS_B		0x140
+			MX8MM_IOMUXC_SAI3_RXC_UART2_DCE_CTS_B		0x140
+		>;
+	};
+
+	pinctrl_usb_eth2: usbeth2grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_NAND_CE1_B_GPIO3_IO2		0x19
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x190
+			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD			0x1d0
+			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d0
+			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d0
+			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d0
+			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d0
+			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x019
+			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0x1d0
+		>;
+	};
+
+	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x194
+			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD			0x1d4
+			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d4
+			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d4
+			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d4
+			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d4
+			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x019
+			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0x1d0
+		>;
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x196
+			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD			0x1d6
+			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d6
+			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d6
+			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d6
+			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d6
+			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x019
+			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0x1d0
+		>;
+	};
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
deleted file mode 100644
index d40caf14ac4a..000000000000
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-s.dts
+++ /dev/null
@@ -1,350 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+ OR MIT
-/*
- * Copyright (C) 2019 Kontron Electronics GmbH
- */
-
-/dts-v1/;
-
-#include "imx8mm-kontron-n801x-som.dtsi"
-
-/ {
-	model = "Kontron i.MX8MM N801X S";
-	compatible = "kontron,imx8mm-n801x-s", "kontron,imx8mm-n801x-som", "fsl,imx8mm";
-
-	aliases {
-		ethernet1 = &usbnet;
-	};
-
-	/* fixed crystal dedicated to mcp2515 */
-	osc_can: clock-osc-can {
-		compatible = "fixed-clock";
-		#clock-cells = <0>;
-		clock-frequency = <16000000>;
-		clock-output-names = "osc-can";
-	};
-
-	leds {
-		compatible = "gpio-leds";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_gpio_led>;
-
-		led1 {
-			label = "led1";
-			gpios = <&gpio4 17 GPIO_ACTIVE_LOW>;
-			linux,default-trigger = "heartbeat";
-		};
-
-		led2 {
-			label = "led2";
-			gpios = <&gpio4 19 GPIO_ACTIVE_LOW>;
-		};
-
-		led3 {
-			label = "led3";
-			gpios = <&gpio4 18 GPIO_ACTIVE_LOW>;
-		};
-
-		led4 {
-			label = "led4";
-			gpios = <&gpio4 8 GPIO_ACTIVE_LOW>;
-		};
-
-		led5 {
-			label = "led5";
-			gpios = <&gpio4 9 GPIO_ACTIVE_LOW>;
-		};
-
-		led6 {
-			label = "led6";
-			gpios = <&gpio4 7 GPIO_ACTIVE_LOW>;
-		};
-	};
-
-	pwm-beeper {
-		compatible = "pwm-beeper";
-		pwms = <&pwm2 0 5000 0>;
-	};
-
-	reg_rst_eth2: regulator-rst-eth2 {
-		compatible = "regulator-fixed";
-		regulator-name = "rst-usb-eth2";
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_usb_eth2>;
-		gpio = <&gpio3 2 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-		regulator-always-on;
-	};
-
-	reg_vdd_5v: regulator-5v {
-		compatible = "regulator-fixed";
-		regulator-name = "vdd-5v";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-	};
-};
-
-&ecspi2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_ecspi2>;
-	cs-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>;
-	status = "okay";
-
-	can0: can@0 {
-		compatible = "microchip,mcp2515";
-		reg = <0>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_can>;
-		clocks = <&osc_can>;
-		interrupt-parent = <&gpio4>;
-		interrupts = <28 IRQ_TYPE_EDGE_FALLING>;
-		spi-max-frequency = <10000000>;
-		vdd-supply = <&reg_vdd_3v3>;
-		xceiver-supply = <&reg_vdd_5v>;
-	};
-};
-
-&ecspi3 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_ecspi3>;
-	cs-gpios = <&gpio5 25 GPIO_ACTIVE_LOW>;
-	status = "okay";
-};
-
-&fec1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_enet>;
-	phy-connection-type = "rgmii-rxid";
-	phy-handle = <&ethphy>;
-	status = "okay";
-
-	mdio {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		ethphy: ethernet-phy@0 {
-			reg = <0>;
-			reset-assert-us = <1>;
-			reset-deassert-us = <15000>;
-			reset-gpios = <&gpio4 27 GPIO_ACTIVE_LOW>;
-		};
-	};
-};
-
-&i2c4 {
-	clock-frequency = <100000>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_i2c4>;
-	status = "okay";
-
-	rtc@32 {
-		compatible = "epson,rx8900";
-		reg = <0x32>;
-	};
-};
-
-&pwm2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_pwm2>;
-	status = "okay";
-};
-
-&uart1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart1>;
-	uart-has-rtscts;
-	status = "okay";
-};
-
-&uart2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart2>;
-	linux,rs485-enabled-at-boot-time;
-	uart-has-rtscts;
-	status = "okay";
-};
-
-&usbotg1 {
-	dr_mode = "otg";
-	over-current-active-low;
-	status = "okay";
-};
-
-&usbotg2 {
-	dr_mode = "host";
-	disable-over-current;
-	#address-cells = <1>;
-	#size-cells = <0>;
-	status = "okay";
-
-	usb1@1 {
-		compatible = "usb424,9514";
-		reg = <1>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		usbnet: usbether@1 {
-			compatible = "usb424,ec00";
-			reg = <1>;
-			local-mac-address = [ 00 00 00 00 00 00 ];
-		};
-	};
-};
-
-&usdhc2 {
-	pinctrl-names = "default", "state_100mhz", "state_200mhz";
-	pinctrl-0 = <&pinctrl_usdhc2>;
-	pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
-	pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
-	vmmc-supply = <&reg_vdd_3v3>;
-	vqmmc-supply = <&reg_nvcc_sd>;
-	cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
-	status = "okay";
-};
-
-&iomuxc {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_gpio>;
-
-	pinctrl_can: cangrp {
-		fsl,pins = <
-			MX8MM_IOMUXC_SAI3_RXFS_GPIO4_IO28		0x19
-		>;
-	};
-
-	pinctrl_ecspi2: ecspi2grp {
-		fsl,pins = <
-			MX8MM_IOMUXC_ECSPI2_MISO_ECSPI2_MISO		0x82
-			MX8MM_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI		0x82
-			MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK		0x82
-			MX8MM_IOMUXC_ECSPI2_SS0_GPIO5_IO13		0x19
-		>;
-	};
-
-	pinctrl_ecspi3: ecspi3grp {
-		fsl,pins = <
-			MX8MM_IOMUXC_UART2_RXD_ECSPI3_MISO		0x82
-			MX8MM_IOMUXC_UART1_TXD_ECSPI3_MOSI		0x82
-			MX8MM_IOMUXC_UART1_RXD_ECSPI3_SCLK		0x82
-			MX8MM_IOMUXC_UART2_TXD_GPIO5_IO25		0x19
-		>;
-	};
-
-	pinctrl_enet: enetgrp {
-		fsl,pins = <
-			MX8MM_IOMUXC_ENET_MDC_ENET1_MDC			0x3
-			MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO		0x3
-			MX8MM_IOMUXC_ENET_TD3_ENET1_RGMII_TD3		0x1f
-			MX8MM_IOMUXC_ENET_TD2_ENET1_RGMII_TD2		0x1f
-			MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1		0x1f
-			MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0		0x1f
-			MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3		0x91
-			MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2		0x91
-			MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1		0x91
-			MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0		0x91
-			MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC		0x1f
-			MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC		0x91
-			MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL	0x91
-			MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL	0x1f
-			MX8MM_IOMUXC_SAI2_MCLK_GPIO4_IO27		0x19 /* PHY RST */
-			MX8MM_IOMUXC_SAI2_TXC_GPIO4_IO25		0x19 /* ETH IRQ */
-		>;
-	};
-
-	pinctrl_gpio_led: gpioledgrp {
-		fsl,pins = <
-			MX8MM_IOMUXC_NAND_READY_B_GPIO3_IO16		0x19
-			MX8MM_IOMUXC_SAI1_RXD5_GPIO4_IO7		0x19
-			MX8MM_IOMUXC_SAI1_RXD6_GPIO4_IO8		0x19
-			MX8MM_IOMUXC_SAI1_RXD7_GPIO4_IO9		0x19
-			MX8MM_IOMUXC_SAI1_TXD5_GPIO4_IO17		0x19
-			MX8MM_IOMUXC_SAI1_TXD6_GPIO4_IO18		0x19
-			MX8MM_IOMUXC_SAI1_TXD7_GPIO4_IO19		0x19
-		>;
-	};
-
-	pinctrl_gpio: gpiogrp {
-		fsl,pins = <
-			MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3		0x19
-			MX8MM_IOMUXC_GPIO1_IO07_GPIO1_IO7		0x19
-			MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9		0x19
-			MX8MM_IOMUXC_GPIO1_IO11_GPIO1_IO11		0x19
-			MX8MM_IOMUXC_GPIO1_IO06_GPIO1_IO6		0x19
-			MX8MM_IOMUXC_GPIO1_IO08_GPIO1_IO8		0x19
-			MX8MM_IOMUXC_GPIO1_IO10_GPIO1_IO10		0x19
-			MX8MM_IOMUXC_SAI3_MCLK_GPIO5_IO2		0x19
-		>;
-	};
-
-	pinctrl_i2c4: i2c4grp {
-		fsl,pins = <
-			MX8MM_IOMUXC_I2C4_SCL_I2C4_SCL			0x400001c3
-			MX8MM_IOMUXC_I2C4_SDA_I2C4_SDA			0x400001c3
-		>;
-	};
-
-	pinctrl_pwm2: pwm2grp {
-		fsl,pins = <
-			MX8MM_IOMUXC_SPDIF_RX_PWM2_OUT			0x19
-		>;
-	};
-
-	pinctrl_uart1: uart1grp {
-		fsl,pins = <
-			MX8MM_IOMUXC_SAI2_RXC_UART1_DCE_RX		0x140
-			MX8MM_IOMUXC_SAI2_RXFS_UART1_DCE_TX		0x140
-			MX8MM_IOMUXC_SAI2_RXD0_UART1_DCE_RTS_B		0x140
-			MX8MM_IOMUXC_SAI2_TXFS_UART1_DCE_CTS_B		0x140
-		>;
-	};
-
-	pinctrl_uart2: uart2grp {
-		fsl,pins = <
-			MX8MM_IOMUXC_SAI3_TXFS_UART2_DCE_RX		0x140
-			MX8MM_IOMUXC_SAI3_TXC_UART2_DCE_TX		0x140
-			MX8MM_IOMUXC_SAI3_RXD_UART2_DCE_RTS_B		0x140
-			MX8MM_IOMUXC_SAI3_RXC_UART2_DCE_CTS_B		0x140
-		>;
-	};
-
-	pinctrl_usb_eth2: usbeth2grp {
-		fsl,pins = <
-			MX8MM_IOMUXC_NAND_CE1_B_GPIO3_IO2		0x19
-		>;
-	};
-
-	pinctrl_usdhc2: usdhc2grp {
-		fsl,pins = <
-			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x190
-			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD			0x1d0
-			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d0
-			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d0
-			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d0
-			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d0
-			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x019
-		>;
-	};
-
-	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
-		fsl,pins = <
-			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x194
-			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD			0x1d4
-			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d4
-			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d4
-			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d4
-			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d4
-			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x019
-		>;
-	};
-
-	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
-		fsl,pins = <
-			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x196
-			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD			0x1d6
-			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d6
-			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d6
-			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d6
-			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d6
-			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x019
-		>;
-	};
-};
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
deleted file mode 100644
index 22a5ef771d4e..000000000000
--- a/arch/arm64/boot/dts/freescale/imx8mm-kontron-n801x-som.dtsi
+++ /dev/null
@@ -1,299 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+ OR MIT
-/*
- * Copyright (C) 2019 Kontron Electronics GmbH
- */
-
-#include "imx8mm.dtsi"
-
-/ {
-	model = "Kontron i.MX8MM N801X SoM";
-	compatible = "kontron,imx8mm-n801x-som", "fsl,imx8mm";
-
-	memory@40000000 {
-		device_type = "memory";
-		/*
-		 * There are multiple SoM flavors with different DDR sizes.
-		 * The smallest is 1GB. For larger sizes the bootloader will
-		 * update the reg property.
-		 */
-		reg = <0x0 0x40000000 0 0x80000000>;
-	};
-
-	chosen {
-		stdout-path = &uart3;
-	};
-};
-
-&A53_0 {
-	cpu-supply = <&reg_vdd_arm>;
-};
-
-&A53_1 {
-	cpu-supply = <&reg_vdd_arm>;
-};
-
-&A53_2 {
-	cpu-supply = <&reg_vdd_arm>;
-};
-
-&A53_3 {
-	cpu-supply = <&reg_vdd_arm>;
-};
-
-&ddrc {
-	operating-points-v2 = <&ddrc_opp_table>;
-
-	ddrc_opp_table: opp-table {
-		compatible = "operating-points-v2";
-
-		opp-25M {
-			opp-hz = /bits/ 64 <25000000>;
-		};
-
-		opp-100M {
-			opp-hz = /bits/ 64 <100000000>;
-		};
-
-		opp-750M {
-			opp-hz = /bits/ 64 <750000000>;
-		};
-	};
-};
-
-&ecspi1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_ecspi1>;
-	cs-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
-	status = "okay";
-
-	spi-flash@0 {
-		compatible = "mxicy,mx25r1635f", "jedec,spi-nor";
-		spi-max-frequency = <80000000>;
-		reg = <0>;
-	};
-};
-
-&i2c1 {
-	clock-frequency = <400000>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_i2c1>;
-	status = "okay";
-
-	pca9450: pmic@25 {
-		compatible = "nxp,pca9450a";
-		reg = <0x25>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_pmic>;
-		interrupt-parent = <&gpio1>;
-		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
-		sd-vsel-gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>;
-
-		regulators {
-			reg_vdd_soc: BUCK1 {
-				regulator-name = "buck1";
-				regulator-min-microvolt = <800000>;
-				regulator-max-microvolt = <850000>;
-				regulator-boot-on;
-				regulator-always-on;
-				regulator-ramp-delay = <3125>;
-				nxp,dvs-run-voltage = <850000>;
-				nxp,dvs-standby-voltage = <800000>;
-			};
-
-			reg_vdd_arm: BUCK2 {
-				regulator-name = "buck2";
-				regulator-min-microvolt = <850000>;
-				regulator-max-microvolt = <950000>;
-				regulator-boot-on;
-				regulator-always-on;
-				regulator-ramp-delay = <3125>;
-				nxp,dvs-run-voltage = <950000>;
-				nxp,dvs-standby-voltage = <850000>;
-			};
-
-			reg_vdd_dram: BUCK3 {
-				regulator-name = "buck3";
-				regulator-min-microvolt = <850000>;
-				regulator-max-microvolt = <950000>;
-				regulator-boot-on;
-				regulator-always-on;
-			};
-
-			reg_vdd_3v3: BUCK4 {
-				regulator-name = "buck4";
-				regulator-min-microvolt = <3300000>;
-				regulator-max-microvolt = <3300000>;
-				regulator-boot-on;
-				regulator-always-on;
-			};
-
-			reg_vdd_1v8: BUCK5 {
-				regulator-name = "buck5";
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <1800000>;
-				regulator-boot-on;
-				regulator-always-on;
-			};
-
-			reg_nvcc_dram: BUCK6 {
-				regulator-name = "buck6";
-				regulator-min-microvolt = <1100000>;
-				regulator-max-microvolt = <1100000>;
-				regulator-boot-on;
-				regulator-always-on;
-			};
-
-			reg_nvcc_snvs: LDO1 {
-				regulator-name = "ldo1";
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <1800000>;
-				regulator-boot-on;
-				regulator-always-on;
-			};
-
-			reg_vdd_snvs: LDO2 {
-				regulator-name = "ldo2";
-				regulator-min-microvolt = <800000>;
-				regulator-max-microvolt = <900000>;
-				regulator-boot-on;
-				regulator-always-on;
-			};
-
-			reg_vdda: LDO3 {
-				regulator-name = "ldo3";
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <1800000>;
-				regulator-boot-on;
-				regulator-always-on;
-			};
-
-			reg_vdd_phy: LDO4 {
-				regulator-name = "ldo4";
-				regulator-min-microvolt = <900000>;
-				regulator-max-microvolt = <900000>;
-				regulator-boot-on;
-				regulator-always-on;
-			};
-
-			reg_nvcc_sd: LDO5 {
-				regulator-name = "ldo5";
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <3300000>;
-			};
-		};
-	};
-};
-
-&uart3 { /* console */
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_uart3>;
-	status = "okay";
-};
-
-&usdhc1 {
-	pinctrl-names = "default", "state_100mhz", "state_200mhz";
-	pinctrl-0 = <&pinctrl_usdhc1>;
-	pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
-	pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
-	vmmc-supply = <&reg_vdd_3v3>;
-	vqmmc-supply = <&reg_vdd_1v8>;
-	bus-width = <8>;
-	non-removable;
-	status = "okay";
-};
-
-&wdog1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_wdog>;
-	fsl,ext-reset-output;
-	status = "okay";
-};
-
-&iomuxc {
-	pinctrl_ecspi1: ecspi1grp {
-		fsl,pins = <
-			MX8MM_IOMUXC_ECSPI1_MISO_ECSPI1_MISO		0x82
-			MX8MM_IOMUXC_ECSPI1_MOSI_ECSPI1_MOSI		0x82
-			MX8MM_IOMUXC_ECSPI1_SCLK_ECSPI1_SCLK		0x82
-			MX8MM_IOMUXC_ECSPI1_SS0_GPIO5_IO9		0x19
-		>;
-	};
-
-	pinctrl_i2c1: i2c1grp {
-		fsl,pins = <
-			MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL			0x400001c3
-			MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA			0x400001c3
-		>;
-	};
-
-	pinctrl_pmic: pmicgrp {
-		fsl,pins = <
-			MX8MM_IOMUXC_GPIO1_IO00_GPIO1_IO0		0x141
-			MX8MM_IOMUXC_GPIO1_IO04_GPIO1_IO4		0x141
-		>;
-	};
-
-	pinctrl_uart3: uart3grp {
-		fsl,pins = <
-			MX8MM_IOMUXC_UART3_RXD_UART3_DCE_RX		0x140
-			MX8MM_IOMUXC_UART3_TXD_UART3_DCE_TX		0x140
-		>;
-	};
-
-	pinctrl_usdhc1: usdhc1grp {
-		fsl,pins = <
-			MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK			0x190
-			MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD			0x1d0
-			MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0		0x1d0
-			MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1		0x1d0
-			MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2		0x1d0
-			MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3		0x1d0
-			MX8MM_IOMUXC_SD1_DATA4_USDHC1_DATA4		0x1d0
-			MX8MM_IOMUXC_SD1_DATA5_USDHC1_DATA5		0x1d0
-			MX8MM_IOMUXC_SD1_DATA6_USDHC1_DATA6		0x1d0
-			MX8MM_IOMUXC_SD1_DATA7_USDHC1_DATA7		0x1d0
-			MX8MM_IOMUXC_SD1_RESET_B_USDHC1_RESET_B		0x019
-			MX8MM_IOMUXC_SD1_STROBE_USDHC1_STROBE		0x190
-		>;
-	};
-
-	pinctrl_usdhc1_100mhz: usdhc1-100mhzgrp {
-		fsl,pins = <
-			MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK			0x194
-			MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD			0x1d4
-			MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0		0x1d4
-			MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1		0x1d4
-			MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2		0x1d4
-			MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3		0x1d4
-			MX8MM_IOMUXC_SD1_DATA4_USDHC1_DATA4		0x1d4
-			MX8MM_IOMUXC_SD1_DATA5_USDHC1_DATA5		0x1d4
-			MX8MM_IOMUXC_SD1_DATA6_USDHC1_DATA6		0x1d4
-			MX8MM_IOMUXC_SD1_DATA7_USDHC1_DATA7		0x1d4
-			MX8MM_IOMUXC_SD1_RESET_B_USDHC1_RESET_B		0x019
-			MX8MM_IOMUXC_SD1_STROBE_USDHC1_STROBE		0x194
-		>;
-	};
-
-	pinctrl_usdhc1_200mhz: usdhc1-200mhzgrp {
-		fsl,pins = <
-			MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK			0x196
-			MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD			0x1d6
-			MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0		0x1d6
-			MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1		0x1d6
-			MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2		0x1d6
-			MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3		0x1d6
-			MX8MM_IOMUXC_SD1_DATA4_USDHC1_DATA4		0x1d6
-			MX8MM_IOMUXC_SD1_DATA5_USDHC1_DATA5		0x1d6
-			MX8MM_IOMUXC_SD1_DATA6_USDHC1_DATA6		0x1d6
-			MX8MM_IOMUXC_SD1_DATA7_USDHC1_DATA7		0x1d6
-			MX8MM_IOMUXC_SD1_RESET_B_USDHC1_RESET_B		0x019
-			MX8MM_IOMUXC_SD1_STROBE_USDHC1_STROBE		0x196
-		>;
-	};
-
-	pinctrl_wdog: wdoggrp {
-		fsl,pins = <
-			MX8MM_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B		0xc6
-		>;
-	};
-};
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi
new file mode 100644
index 000000000000..8d10f5b41297
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-osm-s.dtsi
@@ -0,0 +1,330 @@
+// SPDX-License-Identifier: GPL-2.0+ OR MIT
+/*
+ * Copyright (C) 2022 Kontron Electronics GmbH
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include "imx8mm.dtsi"
+
+/ {
+	model = "Kontron OSM-S i.MX8MM (N802X SOM)";
+	compatible = "kontron,imx8mm-osm-s", "fsl,imx8mm";
+
+	memory@40000000 {
+		device_type = "memory";
+		/*
+		 * There are multiple SoM flavors with different DDR sizes.
+		 * The smallest is 1GB. For larger sizes the bootloader will
+		 * update the reg property.
+		 */
+		reg = <0x0 0x40000000 0 0x80000000>;
+	};
+
+	chosen {
+		stdout-path = &uart3;
+	};
+};
+
+&A53_0 {
+	cpu-supply = <&reg_vdd_arm>;
+};
+
+&A53_1 {
+	cpu-supply = <&reg_vdd_arm>;
+};
+
+&A53_2 {
+	cpu-supply = <&reg_vdd_arm>;
+};
+
+&A53_3 {
+	cpu-supply = <&reg_vdd_arm>;
+};
+
+&ddrc {
+	operating-points-v2 = <&ddrc_opp_table>;
+
+	ddrc_opp_table: opp-table {
+		compatible = "operating-points-v2";
+
+		opp-100M {
+			opp-hz = /bits/ 64 <100000000>;
+		};
+
+		opp-750M {
+			opp-hz = /bits/ 64 <750000000>;
+		};
+	};
+};
+
+&ecspi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1>;
+	cs-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
+	status = "okay";
+
+	flash@0 {
+		compatible = "mxicy,mx25r1635f", "jedec,spi-nor";
+		spi-max-frequency = <80000000>;
+		reg = <0>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "u-boot";
+				reg = <0x0 0x1e0000>;
+			};
+
+			partition@1e0000 {
+				label = "env";
+				reg = <0x1e0000 0x10000>;
+			};
+
+			partition@1f0000 {
+				label = "env_redundant";
+				reg = <0x1f0000 0x10000>;
+			};
+		};
+	};
+};
+
+&i2c1 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+
+	pca9450: pmic@25 {
+		compatible = "nxp,pca9450a";
+		reg = <0x25>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_pmic>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+
+		regulators {
+			reg_vdd_soc: BUCK1 {
+				regulator-name = "+0V8_VDD_SOC (BUCK1)";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <850000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <3125>;
+				nxp,dvs-run-voltage = <850000>;
+				nxp,dvs-standby-voltage = <800000>;
+			};
+
+			reg_vdd_arm: BUCK2 {
+				regulator-name = "+0V9_VDD_ARM (BUCK2)";
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <950000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <3125>;
+				nxp,dvs-run-voltage = <950000>;
+				nxp,dvs-standby-voltage = <850000>;
+			};
+
+			reg_vdd_dram: BUCK3 {
+				regulator-name = "+0V9_VDD_DRAM&PU (BUCK3)";
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <950000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			reg_vdd_3v3: BUCK4 {
+				regulator-name = "+3V3 (BUCK4)";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			reg_vdd_1v8: BUCK5 {
+				regulator-name = "+1V8 (BUCK5)";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			reg_nvcc_dram: BUCK6 {
+				regulator-name = "+1V1_NVCC_DRAM (BUCK6)";
+				regulator-min-microvolt = <1100000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			reg_nvcc_snvs: LDO1 {
+				regulator-name = "+1V8_NVCC_SNVS (LDO1)";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			reg_vdd_snvs: LDO2 {
+				regulator-name = "+0V8_VDD_SNVS (LDO2)";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <900000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			reg_vdda: LDO3 {
+				regulator-name = "+1V8_VDDA (LDO3)";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			reg_vdd_phy: LDO4 {
+				regulator-name = "+0V9_VDD_PHY (LDO4)";
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <900000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			reg_nvcc_sd: LDO5 {
+				regulator-name = "NVCC_SD (LDO5)";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+			};
+		};
+	};
+
+	rtc@52 {
+		compatible = "microcrystal,rv3028";
+		reg = <0x52>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_rtc>;
+		interrupts-extended = <&gpio4 1 IRQ_TYPE_LEVEL_HIGH>;
+		trickle-diode-disable;
+	};
+};
+
+&uart3 { /* console */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	status = "okay";
+};
+
+&usdhc1 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
+	vmmc-supply = <&reg_vdd_3v3>;
+	vqmmc-supply = <&reg_vdd_1v8>;
+	bus-width = <8>;
+	non-removable;
+	status = "okay";
+};
+
+&wdog1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog>;
+	fsl,ext-reset-output;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_ecspi1: ecspi1grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_ECSPI1_MISO_ECSPI1_MISO		0x82
+			MX8MM_IOMUXC_ECSPI1_MOSI_ECSPI1_MOSI		0x82
+			MX8MM_IOMUXC_ECSPI1_SCLK_ECSPI1_SCLK		0x82
+			MX8MM_IOMUXC_ECSPI1_SS0_GPIO5_IO9		0x19
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL			0x400001c3
+			MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA			0x400001c3
+		>;
+	};
+
+	pinctrl_pmic: pmicgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO00_GPIO1_IO0		0x141
+		>;
+	};
+
+	pinctrl_rtc: rtcgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI1_RXC_GPIO4_IO1			0x19
+		>;
+	};
+
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_UART3_RXD_UART3_DCE_RX		0x140
+			MX8MM_IOMUXC_UART3_TXD_UART3_DCE_TX		0x140
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK			0x190
+			MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD			0x1d0
+			MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0		0x1d0
+			MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1		0x1d0
+			MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2		0x1d0
+			MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3		0x1d0
+			MX8MM_IOMUXC_SD1_DATA4_USDHC1_DATA4		0x1d0
+			MX8MM_IOMUXC_SD1_DATA5_USDHC1_DATA5		0x1d0
+			MX8MM_IOMUXC_SD1_DATA6_USDHC1_DATA6		0x1d0
+			MX8MM_IOMUXC_SD1_DATA7_USDHC1_DATA7		0x1d0
+			MX8MM_IOMUXC_SD1_RESET_B_USDHC1_RESET_B		0x019
+			MX8MM_IOMUXC_SD1_STROBE_USDHC1_STROBE		0x190
+		>;
+	};
+
+	pinctrl_usdhc1_100mhz: usdhc1-100mhzgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK			0x194
+			MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD			0x1d4
+			MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0		0x1d4
+			MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1		0x1d4
+			MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2		0x1d4
+			MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3		0x1d4
+			MX8MM_IOMUXC_SD1_DATA4_USDHC1_DATA4		0x1d4
+			MX8MM_IOMUXC_SD1_DATA5_USDHC1_DATA5		0x1d4
+			MX8MM_IOMUXC_SD1_DATA6_USDHC1_DATA6		0x1d4
+			MX8MM_IOMUXC_SD1_DATA7_USDHC1_DATA7		0x1d4
+			MX8MM_IOMUXC_SD1_RESET_B_USDHC1_RESET_B		0x019
+			MX8MM_IOMUXC_SD1_STROBE_USDHC1_STROBE		0x194
+		>;
+	};
+
+	pinctrl_usdhc1_200mhz: usdhc1-200mhzgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK			0x196
+			MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD			0x1d6
+			MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0		0x1d6
+			MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1		0x1d6
+			MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2		0x1d6
+			MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3		0x1d6
+			MX8MM_IOMUXC_SD1_DATA4_USDHC1_DATA4		0x1d6
+			MX8MM_IOMUXC_SD1_DATA5_USDHC1_DATA5		0x1d6
+			MX8MM_IOMUXC_SD1_DATA6_USDHC1_DATA6		0x1d6
+			MX8MM_IOMUXC_SD1_DATA7_USDHC1_DATA7		0x1d6
+			MX8MM_IOMUXC_SD1_RESET_B_USDHC1_RESET_B		0x019
+			MX8MM_IOMUXC_SD1_STROBE_USDHC1_STROBE		0x196
+		>;
+	};
+
+	pinctrl_wdog: wdoggrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B		0xc6
+		>;
+	};
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-kontron-sl.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-kontron-sl.dtsi
new file mode 100644
index 000000000000..0679728d2489
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-kontron-sl.dtsi
@@ -0,0 +1,314 @@
+// SPDX-License-Identifier: GPL-2.0+ OR MIT
+/*
+ * Copyright (C) 2019 Kontron Electronics GmbH
+ */
+
+#include "imx8mm.dtsi"
+
+/ {
+	model = "Kontron SL i.MX8MM (N801X SOM)";
+	compatible = "kontron,imx8mm-sl", "fsl,imx8mm";
+
+	memory@40000000 {
+		device_type = "memory";
+		/*
+		 * There are multiple SoM flavors with different DDR sizes.
+		 * The smallest is 1GB. For larger sizes the bootloader will
+		 * update the reg property.
+		 */
+		reg = <0x0 0x40000000 0 0x80000000>;
+	};
+
+	chosen {
+		stdout-path = &uart3;
+	};
+};
+
+&A53_0 {
+	cpu-supply = <&reg_vdd_arm>;
+};
+
+&A53_1 {
+	cpu-supply = <&reg_vdd_arm>;
+};
+
+&A53_2 {
+	cpu-supply = <&reg_vdd_arm>;
+};
+
+&A53_3 {
+	cpu-supply = <&reg_vdd_arm>;
+};
+
+&ddrc {
+	operating-points-v2 = <&ddrc_opp_table>;
+
+	ddrc_opp_table: opp-table {
+		compatible = "operating-points-v2";
+
+		opp-100M {
+			opp-hz = /bits/ 64 <100000000>;
+		};
+
+		opp-750M {
+			opp-hz = /bits/ 64 <750000000>;
+		};
+	};
+};
+
+&ecspi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1>;
+	cs-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
+	status = "okay";
+
+	flash@0 {
+		compatible = "mxicy,mx25r1635f", "jedec,spi-nor";
+		spi-max-frequency = <80000000>;
+		reg = <0>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "u-boot";
+				reg = <0x0 0x1e0000>;
+			};
+
+			partition@1e0000 {
+				label = "env";
+				reg = <0x1e0000 0x10000>;
+			};
+
+			partition@1f0000 {
+				label = "env_redundant";
+				reg = <0x1f0000 0x10000>;
+			};
+		};
+	};
+};
+
+&i2c1 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+
+	pca9450: pmic@25 {
+		compatible = "nxp,pca9450a";
+		reg = <0x25>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_pmic>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+
+		regulators {
+			reg_vdd_soc: BUCK1 {
+				regulator-name = "+0V8_VDD_SOC (BUCK1)";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <850000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <3125>;
+				nxp,dvs-run-voltage = <850000>;
+				nxp,dvs-standby-voltage = <800000>;
+			};
+
+			reg_vdd_arm: BUCK2 {
+				regulator-name = "+0V9_VDD_ARM (BUCK2)";
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <950000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <3125>;
+				nxp,dvs-run-voltage = <950000>;
+				nxp,dvs-standby-voltage = <850000>;
+			};
+
+			reg_vdd_dram: BUCK3 {
+				regulator-name = "+0V9_VDD_DRAM&PU (BUCK3)";
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <950000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			reg_vdd_3v3: BUCK4 {
+				regulator-name = "+3V3 (BUCK4)";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			reg_vdd_1v8: BUCK5 {
+				regulator-name = "+1V8 (BUCK5)";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			reg_nvcc_dram: BUCK6 {
+				regulator-name = "+1V1_NVCC_DRAM (BUCK6)";
+				regulator-min-microvolt = <1100000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			reg_nvcc_snvs: LDO1 {
+				regulator-name = "+1V8_NVCC_SNVS (LDO1)";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			reg_vdd_snvs: LDO2 {
+				regulator-name = "+0V8_VDD_SNVS (LDO2)";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <900000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			reg_vdda: LDO3 {
+				regulator-name = "+1V8_VDDA (LDO3)";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			reg_vdd_phy: LDO4 {
+				regulator-name = "+0V9_VDD_PHY (LDO4)";
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <900000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			reg_nvcc_sd: LDO5 {
+				regulator-name = "NVCC_SD (LDO5)";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+			};
+		};
+	};
+};
+
+&uart3 { /* console */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	status = "okay";
+};
+
+&usdhc1 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
+	vmmc-supply = <&reg_vdd_3v3>;
+	vqmmc-supply = <&reg_vdd_1v8>;
+	bus-width = <8>;
+	non-removable;
+	status = "okay";
+};
+
+&wdog1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog>;
+	fsl,ext-reset-output;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_ecspi1: ecspi1grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_ECSPI1_MISO_ECSPI1_MISO		0x82
+			MX8MM_IOMUXC_ECSPI1_MOSI_ECSPI1_MOSI		0x82
+			MX8MM_IOMUXC_ECSPI1_SCLK_ECSPI1_SCLK		0x82
+			MX8MM_IOMUXC_ECSPI1_SS0_GPIO5_IO9		0x19
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL			0x400001c3
+			MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA			0x400001c3
+		>;
+	};
+
+	pinctrl_pmic: pmicgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO00_GPIO1_IO0		0x141
+		>;
+	};
+
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_UART3_RXD_UART3_DCE_RX		0x140
+			MX8MM_IOMUXC_UART3_TXD_UART3_DCE_TX		0x140
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK			0x190
+			MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD			0x1d0
+			MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0		0x1d0
+			MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1		0x1d0
+			MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2		0x1d0
+			MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3		0x1d0
+			MX8MM_IOMUXC_SD1_DATA4_USDHC1_DATA4		0x1d0
+			MX8MM_IOMUXC_SD1_DATA5_USDHC1_DATA5		0x1d0
+			MX8MM_IOMUXC_SD1_DATA6_USDHC1_DATA6		0x1d0
+			MX8MM_IOMUXC_SD1_DATA7_USDHC1_DATA7		0x1d0
+			MX8MM_IOMUXC_SD1_RESET_B_USDHC1_RESET_B		0x019
+			MX8MM_IOMUXC_SD1_STROBE_USDHC1_STROBE		0x190
+		>;
+	};
+
+	pinctrl_usdhc1_100mhz: usdhc1-100mhzgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK			0x194
+			MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD			0x1d4
+			MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0		0x1d4
+			MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1		0x1d4
+			MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2		0x1d4
+			MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3		0x1d4
+			MX8MM_IOMUXC_SD1_DATA4_USDHC1_DATA4		0x1d4
+			MX8MM_IOMUXC_SD1_DATA5_USDHC1_DATA5		0x1d4
+			MX8MM_IOMUXC_SD1_DATA6_USDHC1_DATA6		0x1d4
+			MX8MM_IOMUXC_SD1_DATA7_USDHC1_DATA7		0x1d4
+			MX8MM_IOMUXC_SD1_RESET_B_USDHC1_RESET_B		0x019
+			MX8MM_IOMUXC_SD1_STROBE_USDHC1_STROBE		0x194
+		>;
+	};
+
+	pinctrl_usdhc1_200mhz: usdhc1-200mhzgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK			0x196
+			MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD			0x1d6
+			MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0		0x1d6
+			MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1		0x1d6
+			MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2		0x1d6
+			MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3		0x1d6
+			MX8MM_IOMUXC_SD1_DATA4_USDHC1_DATA4		0x1d6
+			MX8MM_IOMUXC_SD1_DATA5_USDHC1_DATA5		0x1d6
+			MX8MM_IOMUXC_SD1_DATA6_USDHC1_DATA6		0x1d6
+			MX8MM_IOMUXC_SD1_DATA7_USDHC1_DATA7		0x1d6
+			MX8MM_IOMUXC_SD1_RESET_B_USDHC1_RESET_B		0x019
+			MX8MM_IOMUXC_SD1_STROBE_USDHC1_STROBE		0x196
+		>;
+	};
+
+	pinctrl_wdog: wdoggrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B		0xc6
+		>;
+	};
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-mx8menlo.dts b/arch/arm64/boot/dts/freescale/imx8mm-mx8menlo.dts
new file mode 100644
index 000000000000..43e89859c044
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-mx8menlo.dts
@@ -0,0 +1,334 @@
+// SPDX-License-Identifier: GPL-2.0+ OR MIT
+/*
+ * Copyright 2021-2022 Marek Vasut <marex@denx.de>
+ */
+
+/dts-v1/;
+
+#include "imx8mm-verdin.dtsi"
+
+/ {
+	model = "MENLO MX8MM EMBEDDED DEVICE";
+	compatible = "menlo,mx8menlo",
+		     "toradex,verdin-imx8mm",
+		     "fsl,imx8mm";
+
+	/delete-node/ gpio-keys;
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_led>;
+
+		led-1 {
+			label = "TestLed601";
+			gpios = <&gpio4 18 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "mmc0";
+		};
+
+		led-2 {
+			label = "TestLed602";
+			gpios = <&gpio4 10 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	beeper {
+		compatible = "gpio-beeper";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_beeper>;
+		gpios = <&gpio5 3 GPIO_ACTIVE_HIGH>;
+	};
+
+	/* Fixed clock dedicated to SPI CAN on carrier board */
+	clk_xtal20: clk-xtal20 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <20000000>;
+	};
+};
+
+&ecspi1 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1>;
+	cs-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
+	status = "okay";
+
+	/* CAN controller on the baseboard */
+	canfd: can@0 {
+		compatible = "microchip,mcp2518fd";
+		clocks = <&clk_xtal20>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <8 IRQ_TYPE_EDGE_FALLING>;
+		reg = <0>;
+		spi-max-frequency = <2000000>;
+	};
+
+};
+
+&ecspi2 {
+	pinctrl-0 = <&pinctrl_ecspi2 &pinctrl_gpio1>;
+	cs-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>, <&gpio3 4 GPIO_ACTIVE_LOW>;
+	status = "okay";
+
+	spidev@0 {
+		compatible = "menlo,m53cpld";
+		reg = <0>;
+		spi-max-frequency = <25000000>;
+	};
+
+	spidev@1 {
+		compatible = "menlo,m53cpld";
+		reg = <1>;
+		spi-max-frequency = <25000000>;
+	};
+
+};
+
+&ethphy0 {
+	max-speed = <100>;
+};
+
+&fec1 {
+	status = "okay";
+};
+
+&flexspi {
+	status = "okay";
+
+	flash@0 {
+		reg = <0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "jedec,spi-nor";
+		spi-max-frequency = <66000000>;
+		spi-rx-bus-width = <4>;
+		spi-tx-bus-width = <4>;
+	};
+};
+
+&gpio1 {
+	gpio-line-names =
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "";
+};
+
+&gpio2 {
+	gpio-line-names =
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "";
+};
+
+&gpio3 {
+	gpio-line-names =
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "DISP_reset", "KBD_intI",
+		"", "", "", "",
+		"", "", "", "";
+};
+
+&gpio4 {
+	/*
+	 * CPLD_D[n] is ARM_CPLD[n] in schematic
+	 * CPLD_int is SA_INTERRUPT in schematic
+	 * CPLD_reset is RESET_SOFT in schematic
+	 */
+	gpio-line-names =
+		"CPLD_D[6]", "CPLD_int", "CPLD_reset", "",
+		"", "CPLD_D[7]", "", "",
+		"", "", "", "CPLD_D[5]",
+		"CPLD_D[4]", "CPLD_D[3]", "CPLD_D[2]", "CPLD_D[1]",
+		"CPLD_D[0]", "", "", "",
+		"", "", "", "",
+		"", "", "", "KBD_intK",
+		"", "", "", "";
+};
+
+&gpio5 {
+	gpio-line-names =
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "",
+		"", "", "", "";
+};
+
+&gpio_expander_21 {
+	status = "okay";
+};
+
+&hwmon {
+	status = "okay";
+};
+
+&i2c3 {
+	status = "okay";
+};
+
+&i2c4 {
+	/* None of this is present on the SoM. */
+	/delete-node/ bridge@2c;
+	/delete-node/ hdmi@48;
+	/delete-node/ touch@4a;
+	/delete-node/ sensor@4f;
+	/delete-node/ eeprom@50;
+	/delete-node/ eeprom@57;
+};
+
+&iomuxc {
+	pinctrl-0 = <&pinctrl_gpio7>, <&pinctrl_gpio_hog1>,
+		    <&pinctrl_gpio_hog2>, <&pinctrl_gpio_hog3>;
+
+	pinctrl_beeper: beepergrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SPDIF_TX_GPIO5_IO3			0x1c4
+		>;
+	};
+
+	pinctrl_ecspi1: ecspi1grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_ECSPI1_SCLK_ECSPI1_SCLK		0x4
+			MX8MM_IOMUXC_ECSPI1_MOSI_ECSPI1_MOSI		0x4
+			MX8MM_IOMUXC_ECSPI1_MISO_ECSPI1_MISO		0x1c4
+			MX8MM_IOMUXC_ECSPI1_SS0_GPIO5_IO9		0x1c4
+		>;
+	};
+
+	pinctrl_led: ledgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI1_TXD6_GPIO4_IO18		0x1c4
+			MX8MM_IOMUXC_SAI1_TXFS_GPIO4_IO10		0x1c4
+		>;
+	};
+
+	pinctrl_uart4_rts: uart4rtsgrp {
+		fsl,pins = <
+			/* SODIMM 222 */
+			MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9		0x184
+		>;
+	};
+};
+
+&pinctrl_gpio1 {
+	fsl,pins = <
+		/* SODIMM 206 */
+		MX8MM_IOMUXC_NAND_CE3_B_GPIO3_IO4			0x1c4
+	>;
+};
+
+&pinctrl_gpio_hog1 {
+	fsl,pins = <
+		/* SODIMM 88 */
+		MX8MM_IOMUXC_SAI1_MCLK_GPIO4_IO20			0x1c4
+		/* CPLD_int */
+		MX8MM_IOMUXC_SAI1_RXC_GPIO4_IO1				0x1c4
+		/* CPLD_reset */
+		MX8MM_IOMUXC_SAI1_RXD0_GPIO4_IO2			0x1c4
+		/* SODIMM 94 */
+		MX8MM_IOMUXC_SAI1_RXD1_GPIO4_IO3			0x1c4
+		/* SODIMM 96 */
+		MX8MM_IOMUXC_SAI1_RXD2_GPIO4_IO4			0x1c4
+		/* CPLD_D[7] */
+		MX8MM_IOMUXC_SAI1_RXD3_GPIO4_IO5			0x184
+		/* CPLD_D[6] */
+		MX8MM_IOMUXC_SAI1_RXFS_GPIO4_IO0			0x184
+		/* CPLD_D[5] */
+		MX8MM_IOMUXC_SAI1_TXC_GPIO4_IO11			0x184
+		/* CPLD_D[4] */
+		MX8MM_IOMUXC_SAI1_TXD0_GPIO4_IO12			0x184
+		/* CPLD_D[3] */
+		MX8MM_IOMUXC_SAI1_TXD1_GPIO4_IO13			0x184
+		/* CPLD_D[2] */
+		MX8MM_IOMUXC_SAI1_TXD2_GPIO4_IO14			0x184
+		/* CPLD_D[1] */
+		MX8MM_IOMUXC_SAI1_TXD3_GPIO4_IO15			0x184
+		/* CPLD_D[0] */
+		MX8MM_IOMUXC_SAI1_TXD4_GPIO4_IO16			0x184
+		/* KBD_intK */
+		MX8MM_IOMUXC_SAI2_MCLK_GPIO4_IO27			0x1c4
+		/* DISP_reset */
+		MX8MM_IOMUXC_SAI5_RXD1_GPIO3_IO22			0x1c4
+		/* KBD_intI */
+		MX8MM_IOMUXC_SAI5_RXD2_GPIO3_IO23			0x1c4
+		/* SODIMM 46 */
+		MX8MM_IOMUXC_SAI5_RXD3_GPIO3_IO24			0x1c4
+	>;
+};
+
+&pinctrl_uart1 {
+	fsl,pins = <
+		/* SODIMM 149 */
+		MX8MM_IOMUXC_SAI2_RXFS_UART1_DCE_TX			0x1c4
+		/* SODIMM 147 */
+		MX8MM_IOMUXC_SAI2_RXC_UART1_DCE_RX			0x1c4
+		/* SODIMM 210 */
+		MX8MM_IOMUXC_UART3_RXD_UART1_DTE_RTS_B			0x1c4
+		/* SODIMM 212 */
+		MX8MM_IOMUXC_UART3_TXD_UART1_DTE_CTS_B			0x1c4
+	>;
+};
+
+&reg_usb_otg1_vbus {
+	/delete-property/ enable-active-high;
+	gpio = <&gpio1 12 GPIO_ACTIVE_LOW>;
+};
+
+&reg_usb_otg2_vbus {
+	/delete-property/ enable-active-high;
+	gpio = <&gpio1 14 GPIO_ACTIVE_LOW>;
+};
+
+&sai2 {
+	status = "disabled";
+};
+
+&uart1 {
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-0 = <&pinctrl_uart4 &pinctrl_uart4_rts>;
+	linux,rs485-enabled-at-boot-time;
+	rts-gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+};
+
+&usbotg1 {
+	dr_mode = "peripheral";
+	status = "okay";
+};
+
+&usbotg2 {
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usdhc2 {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-phyboard-polis-rdk.dts b/arch/arm64/boot/dts/freescale/imx8mm-phyboard-polis-rdk.dts
new file mode 100644
index 000000000000..4a3df2b77b0b
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-phyboard-polis-rdk.dts
@@ -0,0 +1,450 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2022 PHYTEC Messtechnik GmbH
+ * Author: Teresa Remmet <t.remmet@phytec.de>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/phy/phy-imx8-pcie.h>
+#include "imx8mm-phycore-som.dtsi"
+
+/ {
+	model = "PHYTEC phyBOARD-Polis-i.MX8MM RDK";
+	compatible = "phytec,imx8mm-phyboard-polis-rdk",
+		     "phytec,imx8mm-phycore-som", "fsl,imx8mm";
+
+	chosen {
+		stdout-path = &uart3;
+	};
+
+	bt_osc_32k: bt-lp-clock {
+		compatible = "fixed-clock";
+		clock-frequency = <32768>;
+		clock-output-names = "bt_osc_32k";
+		#clock-cells = <0>;
+	};
+
+	can_osc_40m: can-clock {
+		compatible = "fixed-clock";
+		clock-frequency = <40000000>;
+		clock-output-names = "can_osc_40m";
+		#clock-cells = <0>;
+	};
+
+	fan {
+		compatible = "gpio-fan";
+		gpios = <&gpio4 8 GPIO_ACTIVE_HIGH>;
+		gpio-fan,speed-map = <0     0
+				      13000 1>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_fan>;
+		#cooling-cells = <2>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_leds>;
+
+		led-0 {
+			color = <LED_COLOR_ID_RED>;
+			function = LED_FUNCTION_DISK;
+			gpios = <&gpio1 1 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "mmc2";
+		};
+
+		led-1 {
+			color = <LED_COLOR_ID_BLUE>;
+			function = LED_FUNCTION_DISK;
+			gpios = <&gpio1 15 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "mmc1";
+		};
+
+		led-2 {
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_CPU;
+			gpios = <&gpio1 14 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	usdhc1_pwrseq: pwr-seq {
+		compatible = "mmc-pwrseq-simple";
+		post-power-on-delay-ms = <100>;
+		power-off-delay-us = <60>;
+		reset-gpios = <&gpio2 7 GPIO_ACTIVE_LOW>;
+	};
+
+	reg_can_en: regulator-can-en {
+		compatible = "regulator-fixed";
+		gpio = <&gpio1 9 GPIO_ACTIVE_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_can_en>;
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "CAN_EN";
+		startup-delay-us = <20>;
+	};
+
+	reg_usb_otg1_vbus: regulator-usb-otg1 {
+		compatible = "regulator-fixed";
+		gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usbotg1pwrgrp>;
+		regulator-name = "usb_otg1_vbus";
+		regulator-max-microvolt = <5000000>;
+		regulator-min-microvolt = <5000000>;
+	};
+
+	reg_usdhc2_vmmc: regulator-usdhc2 {
+		compatible = "regulator-fixed";
+		gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		off-on-delay-us = <20000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>;
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "VSD_3V3";
+	};
+
+	reg_vcc_3v3: regulator-vcc-3v3 {
+		compatible = "regulator-fixed";
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "VCC_3V3";
+	};
+};
+
+/* SPI - CAN MCP251XFD */
+&ecspi1 {
+	cs-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1>;
+	status = "okay";
+
+	can0: can@0 {
+		compatible = "microchip,mcp251xfd";
+		clocks = <&can_osc_40m>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <8 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_can_int>;
+		reg = <0>;
+		spi-max-frequency = <20000000>;
+		xceiver-supply = <&reg_can_en>;
+	};
+};
+
+&gpio1 {
+	gpio-line-names = "nINT_ETHPHY", "LED_RED", "WDOG_INT", "X_RTC_INT",
+		"", "", "", "RESET_ETHPHY",
+		"CAN_nINT", "CAN_EN", "nENABLE_FLATLINK", "",
+		"USB_OTG_VBUS_EN", "", "LED_GREEN", "LED_BLUE";
+};
+
+&gpio2 {
+	gpio-line-names = "", "", "", "",
+		"", "", "BT_REG_ON", "WL_REG_ON",
+		"BT_DEV_WAKE", "BT_HOST_WAKE", "", "",
+		"X_SD2_CD_B", "", "", "",
+		"", "", "", "SD2_RESET_B";
+};
+
+&gpio4 {
+	gpio-line-names = "", "", "", "",
+		"", "", "", "",
+		"FAN", "miniPCIe_nPERST", "", "",
+		"COEX1", "COEX2";
+};
+
+&gpio5 {
+	gpio-line-names = "", "", "", "",
+		"", "", "", "",
+		"", "ECSPI1_SS0";
+};
+
+/* PCIe */
+&pcie0 {
+	assigned-clocks = <&clk IMX8MM_CLK_PCIE1_AUX>,
+			  <&clk IMX8MM_CLK_PCIE1_CTRL>;
+	assigned-clock-parents = <&clk IMX8MM_SYS_PLL2_50M>,
+				 <&clk IMX8MM_SYS_PLL2_250M>;
+	assigned-clock-rates = <10000000>, <250000000>;
+	clocks = <&clk IMX8MM_CLK_PCIE1_ROOT>, <&clk IMX8MM_CLK_PCIE1_AUX>,
+		 <&clk IMX8MM_CLK_PCIE1_PHY>;
+	clock-names = "pcie", "pcie_aux", "pcie_bus";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pcie>;
+	reset-gpio = <&gpio4 9 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&pcie_phy {
+	clocks = <&clk IMX8MM_CLK_PCIE1_PHY>;
+	fsl,clkreq-unsupported;
+	fsl,refclk-pad-mode = <IMX8_PCIE_REFCLK_PAD_OUTPUT>;
+	fsl,tx-deemph-gen1 = <0x2d>;
+	fsl,tx-deemph-gen2 = <0xf>;
+	status = "okay";
+};
+
+&rv3028 {
+	trickle-resistor-ohms = <3000>;
+};
+
+&snvs_pwrkey {
+	status = "okay";
+};
+
+/* UART - RS232/RS485 */
+&uart1 {
+	assigned-clocks = <&clk IMX8MM_CLK_UART1>;
+	assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_80M>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+/* UART - Sterling-LWB Bluetooth */
+&uart2 {
+	assigned-clocks = <&clk IMX8MM_CLK_UART2>;
+	assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_80M>;
+	fsl,dte-mode;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2_bt>;
+	uart-has-rtscts;
+	status = "okay";
+
+	bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		clocks = <&bt_osc_32k>;
+		clock-names = "lpo";
+		device-wakeup-gpios = <&gpio2 8 GPIO_ACTIVE_HIGH>;
+		interrupt-names = "host-wakeup";
+		interrupt-parent = <&gpio2>;
+		interrupts = <9 IRQ_TYPE_EDGE_BOTH>;
+		max-speed = <2000000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_bt>;
+		shutdown-gpios = <&gpio2 6 GPIO_ACTIVE_HIGH>;
+		vddio-supply = <&reg_vcc_3v3>;
+	};
+};
+
+/* UART - console */
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	status = "okay";
+};
+
+/* USB */
+&usbotg1 {
+	adp-disable;
+	dr_mode = "otg";
+	over-current-active-low;
+	samsung,picophy-pre-emp-curr-control = <3>;
+	samsung,picophy-dc-vol-level-adjust = <7>;
+	srp-disable;
+	vbus-supply = <&reg_usb_otg1_vbus>;
+	status = "okay";
+};
+
+&usbotg2 {
+	disable-over-current;
+	dr_mode = "host";
+	samsung,picophy-pre-emp-curr-control = <3>;
+	samsung,picophy-dc-vol-level-adjust = <7>;
+	status = "okay";
+};
+
+/* SDIO - Sterling-LWB Wifi */
+&usdhc1 {
+	assigned-clocks = <&clk IMX8MM_CLK_USDHC1>;
+	assigned-clock-rates = <200000000>;
+	bus-width = <4>;
+	mmc-pwrseq = <&usdhc1_pwrseq>;
+	non-removable;
+	no-1-8-v;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc1>, <&pinctrl_wlan>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	brcmf: wifi@1 {
+		compatible = "brcm,bcm4329-fmac";
+		reg = <1>;
+	};
+};
+
+/* SD-Card */
+&usdhc2 {
+	assigned-clocks = <&clk IMX8MM_CLK_USDHC2>;
+	assigned-clock-rates = <200000000>;
+	bus-width = <4>;
+	cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
+	disable-wp;
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
+	vmmc-supply = <&reg_usdhc2_vmmc>;
+	vqmmc-supply = <&reg_nvcc_sd2>;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_bt: btgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD1_DATA4_GPIO2_IO6	0x00
+			MX8MM_IOMUXC_SD1_DATA6_GPIO2_IO8	0x00
+			MX8MM_IOMUXC_SD1_DATA7_GPIO2_IO9	0x00
+		>;
+	};
+
+	pinctrl_can_en: can-engrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9	0x00
+		>;
+	};
+
+	pinctrl_can_int: can-intgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO08_GPIO1_IO8	0x00
+		>;
+	};
+
+	pinctrl_ecspi1: ecspi1grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_ECSPI1_MISO_ECSPI1_MISO	0x80
+			MX8MM_IOMUXC_ECSPI1_MOSI_ECSPI1_MOSI	0x80
+			MX8MM_IOMUXC_ECSPI1_SCLK_ECSPI1_SCLK	0x80
+			MX8MM_IOMUXC_ECSPI1_SS0_GPIO5_IO9	0x00
+		>;
+	};
+
+	pinctrl_fan: fan0grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI1_RXD6_GPIO4_IO8	0x16
+		>;
+	};
+
+	pinctrl_leds: leds1grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO01_GPIO1_IO1	0x16
+			MX8MM_IOMUXC_GPIO1_IO14_GPIO1_IO14	0x16
+			MX8MM_IOMUXC_GPIO1_IO15_GPIO1_IO15	0x16
+		>;
+	};
+
+	pinctrl_pcie: pciegrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI1_RXD7_GPIO4_IO9	0x00
+			MX8MM_IOMUXC_SAI1_TXD0_GPIO4_IO12	0x12
+			MX8MM_IOMUXC_SAI1_TXD7_GPIO4_IO19	0x12
+		>;
+	};
+
+	pinctrl_reg_usdhc2_vmmc: regusdhc2vmmcgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD2_RESET_B_GPIO2_IO19	0x40
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI2_RXC_UART1_DCE_RX	0x00
+			MX8MM_IOMUXC_SAI2_RXD0_UART1_DCE_RTS_B	0x00
+			MX8MM_IOMUXC_SAI2_RXFS_UART1_DCE_TX	0x00
+			MX8MM_IOMUXC_SAI2_TXFS_UART1_DCE_CTS_B	0x00
+		>;
+	};
+
+	pinctrl_uart2_bt: uart2btgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI3_RXC_UART2_DTE_RTS_B	0x00
+			MX8MM_IOMUXC_SAI3_RXD_UART2_DTE_CTS_B	0x00
+			MX8MM_IOMUXC_SAI3_TXC_UART2_DTE_RX	0x00
+			MX8MM_IOMUXC_SAI3_TXFS_UART2_DTE_TX	0x00
+		>;
+	};
+
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_UART3_RXD_UART3_DCE_RX	0x40
+			MX8MM_IOMUXC_UART3_TXD_UART3_DCE_TX	0x40
+		>;
+	};
+
+	pinctrl_usbotg1pwrgrp: usbotg1pwrgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO12_GPIO1_IO12	0x00
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK		0x182
+			MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD		0xc6
+			MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0	0xc6
+			MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1	0xc6
+			MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2	0xc6
+			MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3	0xc6
+		>;
+	};
+
+	pinctrl_usdhc2_gpio: usdhc2gpiogrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12	0x40
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT	0x1d0
+			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK		0x192
+			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD		0x1d2
+			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0	0x1d2
+			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1	0x1d2
+			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2	0x1d2
+			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3	0x1d2
+		>;
+	};
+
+	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT	0x1d0
+			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK		0x194
+			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD		0x1d4
+			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0	0x1d4
+			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1	0x1d4
+			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2	0x1d4
+			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3	0x1d4
+		>;
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT	0x1d0
+			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK		0x196
+			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD		0x1d6
+			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0	0x1d6
+			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1	0x1d6
+			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2	0x1d6
+			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3	0x1d6
+		>;
+	};
+
+	pinctrl_wlan: wlangrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD1_DATA5_GPIO2_IO7	0x00
+		>;
+	};
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-phycore-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-phycore-som.dtsi
new file mode 100644
index 000000000000..995b44efb1b6
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-phycore-som.dtsi
@@ -0,0 +1,440 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2022 PHYTEC Messtechnik GmbH
+ * Author: Teresa Remmet <t.remmet@phytec.de>
+ */
+
+#include "imx8mm.dtsi"
+#include <dt-bindings/net/ti-dp83867.h>
+
+/ {
+	model = "PHYTEC phyCORE-i.MX8MM";
+	compatible = "phytec,imx8mm-phycore-som", "fsl,imx8mm";
+
+	aliases {
+		rtc0 = &rv3028;
+		rtc1 = &snvs_rtc;
+	};
+
+	memory@40000000 {
+		device_type = "memory";
+		reg = <0x0 0x40000000 0 0x80000000>;
+	};
+
+	reg_vdd_3v3_s: regulator-vdd-3v3-s {
+		compatible = "regulator-fixed";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "VDD_3V3_S";
+	};
+};
+
+&A53_0 {
+	cpu-supply = <&reg_vdd_arm>;
+};
+
+&A53_1 {
+	cpu-supply = <&reg_vdd_arm>;
+};
+
+&A53_2 {
+	cpu-supply = <&reg_vdd_arm>;
+};
+
+&A53_3 {
+	cpu-supply = <&reg_vdd_arm>;
+};
+
+&ddrc {
+	operating-points-v2 = <&ddrc_opp_table>;
+
+	ddrc_opp_table: opp-table {
+		compatible = "operating-points-v2";
+
+		opp-25M {
+			opp-hz = /bits/ 64 <25000000>;
+		};
+
+		opp-100M {
+			opp-hz = /bits/ 64 <100000000>;
+		};
+
+		opp-750M {
+			opp-hz = /bits/ 64 <750000000>;
+		};
+	};
+};
+
+/* Ethernet */
+&fec1 {
+	fsl,magic-packet;
+	phy-mode = "rgmii-id";
+	phy-handle = <&ethphy0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_fec1>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy0: ethernet-phy@0 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			enet-phy-lane-no-swap;
+			ti,clk-output-sel = <DP83867_CLK_O_SEL_OFF>;
+			ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+			ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+			ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+			reg = <0>;
+			reset-gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
+			reset-assert-us = <1000>;
+			reset-deassert-us = <1000>;
+		};
+	};
+};
+
+/* SPI Flash */
+&flexspi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexspi0>;
+	status = "okay";
+
+	som_flash: flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <80000000>;
+		spi-rx-bus-width = <4>;
+		spi-tx-bus-width = <1>;
+	};
+};
+
+&gpio1 {
+	gpio-line-names = "nINT_ETHPHY", "", "WDOG_INT", "X_RTC_INT",
+		"", "", "", "RESET_ETHPHY",
+		"", "", "nENABLE_FLATLINK";
+};
+
+/* I2C1 */
+&i2c1 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default","gpio";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	pinctrl-1 = <&pinctrl_i2c1_gpio>;
+	scl-gpios = <&gpio5 14 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio5 15 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "okay";
+
+	pmic@8 {
+		compatible = "nxp,pf8121a";
+		reg = <0x08>;
+
+		regulators {
+			reg_nvcc_sd1: ldo1 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <3300000>;
+				regulator-min-microvolt = <3300000>;
+				regulator-name = "NVCC_SD1 (LDO1)";
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			reg_nvcc_sd2: ldo2 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <3300000>;
+				regulator-min-microvolt = <1800000>;
+				regulator-name = "NVCC_SD2 (LDO2)";
+				vselect-en;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			reg_vcc_enet: ldo3 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <2500000>;
+				regulator-min-microvolt = <1500000>;
+				regulator-name = "VCC_ENET_2V5 (LDO3)";
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			reg_vdda_1v8: ldo4 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1800000>;
+				regulator-min-microvolt = <1500000>;
+				regulator-name = "VDDA_1V8 (LDO4)";
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-min-microvolt = <1500000>;
+					regulator-suspend-max-microvolt = <1500000>;
+				};
+			};
+
+			reg_soc_vdda_phy: buck1 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <900000>;
+				regulator-min-microvolt = <400000>;
+				regulator-name = "VDD_SOC_VDDA_PHY_0P8 (BUCK1)";
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-min-microvolt = <400000>;
+					regulator-suspend-max-microvolt = <400000>;
+				};
+			};
+
+			reg_vdd_gpu_dram: buck2 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1000000>;
+				regulator-min-microvolt = <1000000>;
+				regulator-name = "VDD_GPU_DRAM (BUCK2)";
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-max-microvolt = <1000000>;
+					regulator-suspend-min-microvolt = <1000000>;
+				};
+			};
+
+			reg_vdd_gpu: buck3 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1000000>;
+				regulator-min-microvolt = <400000>;
+				regulator-name = "VDD_VPU (BUCK3)";
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			reg_vdd_mipi: buck4 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1050000>;
+				regulator-min-microvolt = <900000>;
+				regulator-name = "VDD_MIPI_0P9 (BUCK4)";
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			reg_vdd_arm: buck5 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1050000>;
+				regulator-min-microvolt = <400000>;
+				regulator-name = "VDD_ARM (BUCK5)";
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			reg_vdd_1v8: buck6 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1800000>;
+				regulator-min-microvolt = <1800000>;
+				regulator-name = "VDD_1V8 (BUCK6)";
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-max-microvolt = <1800000>;
+					regulator-suspend-min-microvolt = <1800000>;
+				};
+			};
+
+			reg_nvcc_dram: buck7 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1100000>;
+				regulator-min-microvolt = <1100000>;
+				regulator-name = "NVCC_DRAM_1P1V (BUCK7)";
+			};
+
+			reg_vsnvs: vsnvs {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1800000>;
+				regulator-min-microvolt = <1800000>;
+				regulator-name = "NVCC_SNVS_1P8 (VSNVS)";
+			};
+		};
+	};
+
+	sn65dsi83: bridge@2d {
+		compatible = "ti,sn65dsi83";
+		enable-gpios = <&gpio1 10 GPIO_ACTIVE_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_sn65dsi83>;
+		reg = <0x2d>;
+		status = "disabled";
+	};
+
+	eeprom@51 {
+		compatible = "atmel,24c32";
+		pagesize = <32>;
+		reg = <0x51>;
+		vcc-supply = <&reg_vdd_3v3_s>;
+	};
+
+	rv3028: rtc@52 {
+		compatible = "microcrystal,rv3028";
+		interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-parent = <&gpio1>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_rtc>;
+		reg = <0x52>;
+	};
+};
+
+/* EMMC */
+&usdhc3 {
+	assigned-clocks = <&clk IMX8MM_CLK_USDHC3_ROOT>;
+	assigned-clock-rates = <400000000>;
+	bus-width = <8>;
+	keep-power-in-suspend;
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+	non-removable;
+	status = "okay";
+};
+
+/* Watchdog */
+&wdog1 {
+	fsl,ext-reset-output;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog>;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_fec1: fec1grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_ENET_MDC_ENET1_MDC			0x2
+			MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO		0x2
+			MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0		0x90
+			MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1		0x90
+			MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2		0x90
+			MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3		0x90
+			MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC		0x90
+			MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL	0x90
+			MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0		0x16
+			MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1		0x16
+			MX8MM_IOMUXC_ENET_TD2_ENET1_RGMII_TD2		0x16
+			MX8MM_IOMUXC_ENET_TD3_ENET1_RGMII_TD3		0x16
+			MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC		0x16
+			MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL	0x16
+			MX8MM_IOMUXC_GPIO1_IO07_GPIO1_IO7		0x10
+		>;
+	};
+
+	pinctrl_flexspi0: flexspi0grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_NAND_ALE_QSPI_A_SCLK		0x1c2
+			MX8MM_IOMUXC_NAND_CE0_B_QSPI_A_SS0_B		0x82
+			MX8MM_IOMUXC_NAND_DATA00_QSPI_A_DATA0		0x82
+			MX8MM_IOMUXC_NAND_DATA01_QSPI_A_DATA1		0x82
+			MX8MM_IOMUXC_NAND_DATA02_QSPI_A_DATA2		0x82
+			MX8MM_IOMUXC_NAND_DATA03_QSPI_A_DATA3		0x82
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA			0x400001c0
+			MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL			0x400001c0
+		>;
+	};
+
+	pinctrl_i2c1_gpio: i2c1gpiogrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_I2C1_SDA_GPIO5_IO15		0x1e0
+			MX8MM_IOMUXC_I2C1_SCL_GPIO5_IO14		0x1e0
+		>;
+	};
+
+	pinctrl_rtc: rtcgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3		0x1c0
+		>;
+	};
+
+	pinctrl_sn65dsi83: sn65dsi83grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO10_GPIO1_IO10		0x0
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7		0x1d0
+			MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE		0x190
+			MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5		0x1d0
+			MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6		0x1d0
+			MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0		0x1d0
+			MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1		0x1d0
+			MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2		0x1d0
+			MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3		0x1d0
+			MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4		0x1d0
+			MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK		0x190
+			MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD		0x1d0
+		>;
+	};
+
+	pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7		0x1d4
+			MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE		0x194
+			MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5		0x1d4
+			MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6		0x1d4
+			MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0		0x1d4
+			MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1		0x1d4
+			MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2		0x1d4
+			MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3		0x1d4
+			MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4		0x1d4
+			MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK		0x194
+			MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD		0x1d4
+		>;
+	};
+
+	pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7		0x1d6
+			MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE		0x196
+			MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5		0x1d6
+			MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6		0x1d6
+			MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0		0x1d6
+			MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1		0x1d6
+			MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2		0x1d6
+			MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3		0x1d6
+			MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4		0x1d6
+			MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK		0x196
+			MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD		0x1d6
+		>;
+	};
+
+	pinctrl_wdog: wdoggrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B		0x26
+		>;
+	};
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-pinfunc.h b/arch/arm64/boot/dts/freescale/imx8mm-pinfunc.h
index a003e6af3353..83c8f715cd90 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-pinfunc.h
+++ b/arch/arm64/boot/dts/freescale/imx8mm-pinfunc.h
@@ -248,6 +248,7 @@
 #define MX8MM_IOMUXC_NAND_RE_B_GPIO3_IO15                                   0x130 0x398 0x000 0x5 0x0
 #define MX8MM_IOMUXC_NAND_RE_B_SIM_M_HADDR11                                0x130 0x398 0x000 0x7 0x0
 #define MX8MM_IOMUXC_NAND_READY_B_RAWNAND_READY_B                           0x134 0x39C 0x000 0x0 0x0
+#define MX8MM_IOMUXC_NAND_READY_B_SD3_RESET_B                               0x134 0x39C 0x000 0x2 0x0
 #define MX8MM_IOMUXC_NAND_READY_B_GPIO3_IO16                                0x134 0x39C 0x000 0x5 0x0
 #define MX8MM_IOMUXC_NAND_READY_B_SIM_M_HADDR12                             0x134 0x39C 0x000 0x7 0x0
 #define MX8MM_IOMUXC_NAND_WE_B_RAWNAND_WE_B                                 0x138 0x3A0 0x000 0x0 0x0
@@ -279,7 +280,7 @@
 #define MX8MM_IOMUXC_SAI5_RXD2_SAI1_TX_DATA4                                0x150 0x3B8 0x000 0x1 0x0
 #define MX8MM_IOMUXC_SAI5_RXD2_SAI1_TX_SYNC                                 0x150 0x3B8 0x4CC 0x2 0x1
 #define MX8MM_IOMUXC_SAI5_RXD2_SAI5_TX_BCLK                                 0x150 0x3B8 0x4E8 0x3 0x0
-#define MX8MM_IOMUXC_SAI5_RXD2_PDM_DATA2                                    0x150 0x3B8 0x53c 0x4 0x0
+#define MX8MM_IOMUXC_SAI5_RXD2_PDM_DATA2                                    0x150 0x3B8 0x53C 0x4 0x0
 #define MX8MM_IOMUXC_SAI5_RXD2_GPIO3_IO23                                   0x150 0x3B8 0x000 0x5 0x0
 #define MX8MM_IOMUXC_SAI5_RXD3_SAI5_RX_DATA3                                0x154 0x3BC 0x4E0 0x0 0x0
 #define MX8MM_IOMUXC_SAI5_RXD3_SAI1_TX_DATA5                                0x154 0x3BC 0x000 0x1 0x0
@@ -486,7 +487,7 @@
 #define MX8MM_IOMUXC_SAI3_TXFS_SAI3_TX_SYNC                                 0x1D8 0x440 0x000 0x0 0x0
 #define MX8MM_IOMUXC_SAI3_TXFS_GPT1_CAPTURE2                                0x1D8 0x440 0x000 0x1 0x0
 #define MX8MM_IOMUXC_SAI3_TXFS_SAI5_RX_DATA1                                0x1D8 0x440 0x4D8 0x2 0x2
-#define MX8MM_IOMUXC_SAI3_TXFS_UART2_DCE_RX                                 0x1D8 0x440 0x4Fc 0x4 0x2
+#define MX8MM_IOMUXC_SAI3_TXFS_UART2_DCE_RX                                 0x1D8 0x440 0x4FC 0x4 0x2
 #define MX8MM_IOMUXC_SAI3_TXFS_UART2_DTE_TX                                 0x1D8 0x440 0x000 0x4 0x0
 #define MX8MM_IOMUXC_SAI3_TXFS_GPIO4_IO31                                   0x1D8 0x440 0x000 0x5 0x0
 #define MX8MM_IOMUXC_SAI3_TXFS_TPSMP_HDATA1                                 0x1D8 0x440 0x000 0x7 0x0
@@ -494,7 +495,7 @@
 #define MX8MM_IOMUXC_SAI3_TXC_GPT1_COMPARE2                                 0x1DC 0x444 0x000 0x1 0x0
 #define MX8MM_IOMUXC_SAI3_TXC_SAI5_RX_DATA2                                 0x1DC 0x444 0x4DC 0x2 0x2
 #define MX8MM_IOMUXC_SAI3_TXC_UART2_DCE_TX                                  0x1DC 0x444 0x000 0x4 0x0
-#define MX8MM_IOMUXC_SAI3_TXC_UART2_DTE_RX                                  0x1DC 0x444 0x4Fc 0x4 0x3
+#define MX8MM_IOMUXC_SAI3_TXC_UART2_DTE_RX                                  0x1DC 0x444 0x4FC 0x4 0x3
 #define MX8MM_IOMUXC_SAI3_TXC_GPIO5_IO0                                     0x1DC 0x444 0x000 0x5 0x0
 #define MX8MM_IOMUXC_SAI3_TXC_TPSMP_HDATA2                                  0x1DC 0x444 0x000 0x7 0x0
 #define MX8MM_IOMUXC_SAI3_TXD_SAI3_TX_DATA0                                 0x1E0 0x448 0x000 0x0 0x0
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-prt8mm.dts b/arch/arm64/boot/dts/freescale/imx8mm-prt8mm.dts
new file mode 100644
index 000000000000..9fbbbb556c0b
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-prt8mm.dts
@@ -0,0 +1,304 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2020 Protonic Holland
+ * Copyright 2019 NXP
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/usb/pd.h>
+#include "imx8mm.dtsi"
+
+/ {
+	model = "Protonic PRT8MM";
+	compatible = "prt,prt8mm", "fsl,imx8mm";
+
+	chosen {
+		stdout-path = &uart4;
+	};
+
+	memory@40000000 {
+		device_type = "memory";
+		reg = <0x0 0x40000000 0 0x40000000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_leds>;
+
+		debug-led0 {
+			label = "DEBUG_LED0";
+			gpios = <&gpio3 0 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+
+		debug-led1 {
+			label = "DEBUG_LED1";
+			gpios = <&gpio3 1 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "cpu";
+		};
+	};
+
+	sound-ssm2518 {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "ssm2518-audio";
+		simple-audio-card,format = "i2s";
+		simple-audio-card,frame-master = <&cpudai>;
+		simple-audio-card,bitclock-master = <&cpudai>;
+
+		cpudai: simple-audio-card,cpu {
+			sound-dai = <&sai3>;
+		};
+
+		simple-audio-card,codec {
+			sound-dai = <&ssm2518>;
+			clocks = <&clk IMX8MM_CLK_SAI3_ROOT>;
+		};
+	};
+};
+
+&i2c1 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+
+	ssm2518: audio-codec@34 {
+		compatible = "adi,ssm2518";
+		reg = <0x34>;
+		#sound-dai-cells = <0>;
+	};
+};
+
+&i2c2 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	status = "okay";
+
+	regulator@60 {
+		compatible = "fcs,fan53555";
+		reg = <0x60>;
+		regulator-name = "0V9_CORE";
+		regulator-min-microvolt = <900000>;
+		regulator-max-microvolt = <980000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+};
+
+&i2c3 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "okay";
+
+	rtc@51 {
+		compatible = "nxp,pcf85363";
+		reg = <0x51>;
+	};
+
+	touchscreeen@5d {
+		compatible = "goodix,gt911";
+		reg = <0x5d>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_touchscreen>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <8 IRQ_TYPE_NONE>;
+		irq-gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+		reset-gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
+	};
+
+	temp-sense@70 {
+		compatible = "ti,tmp103";
+		reg = <0x70>;
+	};
+};
+
+&sai3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sai3>;
+	assigned-clocks = <&clk IMX8MM_CLK_SAI3>;
+	assigned-clock-parents = <&clk IMX8MM_AUDIO_PLL1_OUT>;
+	assigned-clock-rates = <12288000>;
+	fsl,sai-mclk-direction-output;
+	fsl,sai-asynchronous;
+	status = "okay";
+};
+
+&snvs_pwrkey {
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+	status = "okay";
+};
+
+&usbotg1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg1>;
+	dr_mode = "host";
+	disable-over-current;
+	power-active-high;
+	status = "okay";
+};
+
+&usdhc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	assigned-clocks = <&clk IMX8MM_CLK_USDHC2>;
+	assigned-clock-rates = <100000000>;
+	cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&usdhc3 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+	assigned-clocks = <&clk IMX8MM_CLK_USDHC3_ROOT>;
+	assigned-clock-rates = <400000000>;
+	bus-width = <8>;
+	non-removable;
+	no-sdio;
+	no-sd;
+	status = "okay";
+};
+
+&wdog1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog>;
+	fsl,ext-reset-output;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_gpio_leds: ledsgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_NAND_ALE_GPIO3_IO0			0x00
+			MX8MM_IOMUXC_NAND_CE0_B_GPIO3_IO1		0x00
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL			0x400000c3
+			MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA			0x400000c3
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_I2C2_SCL_I2C2_SCL			0x400000c3
+			MX8MM_IOMUXC_I2C2_SDA_I2C2_SDA			0x400000c3
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_I2C3_SCL_I2C3_SCL			0x400000c3
+			MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA			0x400000c3
+		>;
+	};
+
+	pinctrl_sai3: sai3grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI3_TXFS_SAI3_TX_SYNC		0xd6
+			MX8MM_IOMUXC_SAI3_TXC_SAI3_TX_BCLK		0xd6
+			MX8MM_IOMUXC_SAI3_MCLK_SAI3_MCLK		0xd6
+			MX8MM_IOMUXC_SAI3_TXD_SAI3_TX_DATA0		0xd6
+		>;
+	};
+
+	pinctrl_touchscreen: tsgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO08_GPIO1_IO8		0x80
+			MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9		0x80
+		>;
+	};
+
+	pinctrl_uart4: uart4grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_UART4_RXD_UART4_DCE_RX		0x040
+			MX8MM_IOMUXC_UART4_TXD_UART4_DCE_TX		0x040
+		>;
+	};
+
+	pinctrl_usbotg1: usbotg1grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO12_USB1_OTG_PWR		0x000
+			MX8MM_IOMUXC_GPIO1_IO13_USB1_OTG_OC		0x000
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK			0x190
+			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD			0x1d0
+			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d0
+			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d0
+			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d0
+			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d0
+			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x0d4
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK		0x190
+			MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD		0x1d0
+			MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0		0x1d0
+			MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1		0x1d0
+			MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2		0x1d0
+			MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3		0x1d0
+			MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4		0x1d0
+			MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5		0x1d0
+			MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6		0x1d0
+			MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7		0x1d0
+			MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE		0x190
+		>;
+	};
+
+	pinctrl_usdhc3_100mhz: usdhc3grp100mhz {
+		fsl,pins = <
+			MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK		0x194
+			MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD		0x1d4
+			MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0		0x1d4
+			MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1		0x1d4
+			MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2		0x1d4
+			MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3		0x1d4
+			MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4		0x1d4
+			MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5		0x1d4
+			MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6		0x1d4
+			MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7		0x1d4
+			MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE		0x194
+		>;
+	};
+
+	pinctrl_usdhc3_200mhz: usdhc3grp200mhz {
+		fsl,pins = <
+			MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK		0x196
+			MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD		0x1d6
+			MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0		0x1d6
+			MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1		0x1d6
+			MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2		0x1d6
+			MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3		0x1d6
+			MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4		0x1d6
+			MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5		0x1d6
+			MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6		0x1d6
+			MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7		0x1d6
+			MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE		0x196
+		>;
+	};
+
+	pinctrl_wdog: wdoggrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B		0xc6
+		>;
+	};
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml-mba8mx.dts b/arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml-mba8mx.dts
new file mode 100644
index 000000000000..7e0aeb2db305
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml-mba8mx.dts
@@ -0,0 +1,271 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2020-2021 TQ-Systems GmbH
+ */
+
+/dts-v1/;
+
+#include "imx8mm-tqma8mqml.dtsi"
+#include "mba8mx.dtsi"
+
+/ {
+	model = "TQ-Systems GmbH i.MX8MM TQMa8MxML on MBa8Mx";
+	compatible = "tq,imx8mm-tqma8mqml-mba8mx", "tq,imx8mm-tqma8mqml", "fsl,imx8mm";
+
+	aliases {
+		eeprom0 = &eeprom3;
+		mmc0 = &usdhc3;
+		mmc1 = &usdhc2;
+		mmc2 = &usdhc1;
+		rtc0 = &pcf85063;
+		rtc1 = &snvs_rtc;
+	};
+
+	reg_usdhc2_vmmc: regulator-vmmc {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>;
+		regulator-name = "VSD_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		startup-delay-us = <100>;
+		off-on-delay-us = <12000>;
+	};
+
+	extcon_usbotg1: extcon-usbotg1 {
+		compatible = "linux,extcon-usb-gpio";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usb1_extcon>;
+		id-gpio = <&gpio1 10 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&i2c1 {
+	expander2: gpio@27 {
+		compatible = "nxp,pca9555";
+		reg = <0x27>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		vcc-supply = <&reg_vcc_3v3>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_expander>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <9 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+};
+
+&pcie_phy {
+	clocks = <&pcie0_refclk>;
+	status = "okay";
+};
+
+&pcie0 {
+	reset-gpio = <&expander0 14 GPIO_ACTIVE_LOW>;
+	clocks = <&clk IMX8MM_CLK_PCIE1_ROOT>, <&clk IMX8MM_CLK_PCIE1_AUX>,
+		<&pcie0_refclk>;
+	clock-names = "pcie", "pcie_aux", "pcie_bus";
+	assigned-clocks = <&clk IMX8MM_CLK_PCIE1_AUX>,
+				<&clk IMX8MM_CLK_PCIE1_CTRL>;
+	assigned-clock-rates = <10000000>, <250000000>;
+	assigned-clock-parents = <&clk IMX8MM_SYS_PLL2_50M>,
+				<&clk IMX8MM_SYS_PLL2_250M>;
+	status = "okay";
+};
+
+&sai3 {
+	assigned-clocks = <&clk IMX8MM_CLK_SAI3>;
+	assigned-clock-parents = <&clk IMX8MM_AUDIO_PLL1_OUT>;
+	clock-names = "bus", "mclk0", "mclk1", "mclk2", "mclk3", "pll8k", "pll11k";
+	clocks = <&clk IMX8MM_CLK_SAI3_IPG>, <&clk IMX8MM_CLK_DUMMY>,
+		<&clk IMX8MM_CLK_SAI3_ROOT>, <&clk IMX8MM_CLK_DUMMY>,
+		<&clk IMX8MM_CLK_DUMMY>, <&clk IMX8MM_AUDIO_PLL1_OUT>,
+		<&clk IMX8MM_AUDIO_PLL2_OUT>;
+};
+
+&tlv320aic3x04 {
+	clock-names = "mclk";
+	clocks = <&clk IMX8MM_CLK_SAI3_ROOT>;
+};
+
+&uart1 {
+	assigned-clocks = <&clk IMX8MM_CLK_UART1>;
+	assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_80M>;
+};
+
+&uart2 {
+	assigned-clocks = <&clk IMX8MM_CLK_UART2>;
+	assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_80M>;
+};
+
+&usbotg1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg1>;
+	dr_mode = "otg";
+	extcon = <&extcon_usbotg1>;
+	srp-disable;
+	hnp-disable;
+	adp-disable;
+	power-active-high;
+	over-current-active-low;
+	status = "okay";
+};
+
+&usbotg2 {
+	dr_mode = "host";
+	disable-over-current;
+	vbus-supply = <&reg_hub_vbus>;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_ecspi1: ecspi1grp {
+		fsl,pins = <MX8MM_IOMUXC_ECSPI1_SCLK_ECSPI1_SCLK	0x00000006>,
+			   <MX8MM_IOMUXC_ECSPI1_MOSI_ECSPI1_MOSI	0x00000006>,
+			   <MX8MM_IOMUXC_ECSPI1_MISO_ECSPI1_MISO	0x00000006>,
+			   <MX8MM_IOMUXC_ECSPI1_SS0_GPIO5_IO9		0x00000006>;
+	};
+
+	pinctrl_ecspi2: ecspi2grp {
+		fsl,pins = <MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK	0x00000006>,
+			   <MX8MM_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI	0x00000006>,
+			   <MX8MM_IOMUXC_ECSPI2_MISO_ECSPI2_MISO	0x00000006>,
+			   <MX8MM_IOMUXC_ECSPI2_SS0_GPIO5_IO13		0x00000006>;
+	};
+
+	pinctrl_expander: expandergrp {
+		fsl,pins = <MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9		0x94>;
+	};
+
+	pinctrl_fec1: fec1grp {
+		fsl,pins = <MX8MM_IOMUXC_ENET_MDC_ENET1_MDC		0x40000002>,
+			   <MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO		0x40000002>,
+			   <MX8MM_IOMUXC_ENET_TD3_ENET1_RGMII_TD3	0x14>,
+			   <MX8MM_IOMUXC_ENET_TD2_ENET1_RGMII_TD2	0x14>,
+			   <MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1	0x14>,
+			   <MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0	0x14>,
+			   <MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3	0x90>,
+			   <MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2	0x90>,
+			   <MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1	0x90>,
+			   <MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0	0x90>,
+			   <MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC	0x14>,
+			   <MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC	0x90>,
+			   <MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL	0x90>,
+			   <MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL	0x14>;
+	};
+
+	pinctrl_gpiobutton: gpiobuttongrp {
+		fsl,pins = <MX8MM_IOMUXC_GPIO1_IO05_GPIO1_IO5		0x84>,
+			   <MX8MM_IOMUXC_GPIO1_IO07_GPIO1_IO7		0x84>,
+			   <MX8MM_IOMUXC_SD1_CLK_GPIO2_IO0		0x84>;
+	};
+
+	pinctrl_gpioled: gpioledgrp {
+		fsl,pins = <MX8MM_IOMUXC_GPIO1_IO00_GPIO1_IO0		0x84>,
+			   <MX8MM_IOMUXC_NAND_DQS_GPIO3_IO14		0x84>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <MX8MM_IOMUXC_I2C2_SCL_I2C2_SCL		0x40000004>,
+			   <MX8MM_IOMUXC_I2C2_SDA_I2C2_SDA		0x40000004>;
+	};
+
+	pinctrl_i2c2_gpio: i2c2gpiogrp {
+		fsl,pins = <MX8MM_IOMUXC_I2C2_SCL_GPIO5_IO16		0x40000004>,
+			   <MX8MM_IOMUXC_I2C2_SDA_GPIO5_IO17		0x40000004>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <MX8MM_IOMUXC_I2C3_SCL_I2C3_SCL		0x40000004>,
+			   <MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA		0x40000004>;
+	};
+
+	pinctrl_i2c3_gpio: i2c3gpiogrp {
+		fsl,pins = <MX8MM_IOMUXC_I2C3_SCL_GPIO5_IO18		0x40000004>,
+			   <MX8MM_IOMUXC_I2C3_SDA_GPIO5_IO19		0x40000004>;
+	};
+
+	pinctrl_pwm3: pwm3grp {
+		fsl,pins = <MX8MM_IOMUXC_GPIO1_IO14_PWM3_OUT		0x14>;
+	};
+
+	pinctrl_pwm4: pwm4grp {
+		fsl,pins = <MX8MM_IOMUXC_GPIO1_IO15_PWM4_OUT		0x14>;
+	};
+
+	pinctrl_sai3: sai3grp {
+		fsl,pins = <MX8MM_IOMUXC_SAI3_MCLK_SAI3_MCLK		0x94>,
+			   <MX8MM_IOMUXC_SAI3_RXC_SAI3_RX_BCLK		0x94>,
+			   <MX8MM_IOMUXC_SAI3_RXFS_SAI3_RX_SYNC		0x94>,
+			   <MX8MM_IOMUXC_SAI3_RXD_SAI3_RX_DATA0		0x94>,
+			   <MX8MM_IOMUXC_SAI3_TXFS_SAI3_TX_SYNC		0x94>,
+			   <MX8MM_IOMUXC_SAI3_TXD_SAI3_TX_DATA0		0x94>,
+			   <MX8MM_IOMUXC_SAI3_TXC_SAI3_TX_BCLK		0x94>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <MX8MM_IOMUXC_UART1_RXD_UART1_DCE_RX		0x16>,
+			   <MX8MM_IOMUXC_UART1_TXD_UART1_DCE_TX		0x16>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <MX8MM_IOMUXC_UART2_RXD_UART2_DCE_RX		0x16>,
+			   <MX8MM_IOMUXC_UART2_TXD_UART2_DCE_TX		0x16>;
+	};
+
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <MX8MM_IOMUXC_UART3_RXD_UART3_DCE_RX		0x16>,
+			   <MX8MM_IOMUXC_UART3_TXD_UART3_DCE_TX		0x16>;
+	};
+
+	pinctrl_uart4: uart4grp {
+		fsl,pins = <MX8MM_IOMUXC_UART4_RXD_UART4_DCE_RX		0x16>,
+			   <MX8MM_IOMUXC_UART4_TXD_UART4_DCE_TX		0x16>;
+	};
+
+	pinctrl_usbotg1: usbotg1grp {
+		fsl,pins = <MX8MM_IOMUXC_GPIO1_IO12_USB1_OTG_PWR	0x84>,
+			   <MX8MM_IOMUXC_GPIO1_IO13_USB1_OTG_OC		0x84>;
+	};
+
+	pinctrl_usb1_extcon: usb1-extcongrp {
+		fsl,pins = <MX8MM_IOMUXC_GPIO1_IO10_GPIO1_IO10		0x1c0>;
+	};
+
+	pinctrl_usdhc2_gpio: usdhc2grpgpiogrp {
+		fsl,pins = <MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x84>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK		0x1d4>,
+			   <MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD		0x1d4>,
+			   <MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d4>,
+			   <MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d4>,
+			   <MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d4>,
+			   <MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d4>,
+			   <MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT	0x84>;
+	};
+
+	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+		fsl,pins = <MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK		0x1d4>,
+			   <MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD		0x1d4>,
+			   <MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d4>,
+			   <MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d4>,
+			   <MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d4>,
+			   <MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d4>,
+			   <MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT	0x84>;
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+		fsl,pins = <MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK		0x1d4>,
+			   <MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD		0x1d4>,
+			   <MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d4>,
+			   <MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d4>,
+			   <MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d4>,
+			   <MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d4>,
+			   <MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT	0x84>;
+	};
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml.dtsi
new file mode 100644
index 000000000000..f649dfacb4b6
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-tqma8mqml.dtsi
@@ -0,0 +1,341 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2020-2021 TQ-Systems GmbH
+ */
+
+#include <dt-bindings/phy/phy-imx8-pcie.h>
+#include "imx8mm.dtsi"
+
+/ {
+	model = "TQ-Systems GmbH i.MX8MM TQMa8MxML";
+	compatible = "tq,imx8mm-tqma8mqml", "fsl,imx8mm";
+
+	memory@40000000 {
+		device_type = "memory";
+		/*  our minimum RAM config will be 1024 MiB */
+		reg = <0x00000000 0x40000000 0 0x40000000>;
+	};
+
+	/* e-MMC IO, needed for HS modes */
+	reg_vcc1v8: regulator-vcc1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "TQMA8MXML_VCC1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	/* identical to buck4_reg, but should never change */
+	reg_vcc3v3: regulator-vcc3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "TQMA8MXML_VCC3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		/* global autoconfigured region for contiguous allocations */
+		linux,cma {
+			compatible = "shared-dma-pool";
+			reusable;
+			/* 640 MiB */
+			size = <0 0x28000000>;
+			/*  1024 - 128 MiB, our minimum RAM config will be 1024 MiB */
+			alloc-ranges = <0 0x40000000 0 0x78000000>;
+			linux,cma-default;
+		};
+	};
+};
+
+&A53_0 {
+	cpu-supply = <&buck2_reg>;
+};
+
+&flexspi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexspi>;
+	status = "okay";
+
+	flash0: flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		spi-max-frequency = <84000000>;
+		spi-tx-bus-width = <1>;
+		spi-rx-bus-width = <4>;
+	};
+};
+
+&gpu_2d {
+	status = "okay";
+};
+
+&gpu_3d {
+	status = "okay";
+};
+
+&i2c1 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	pinctrl-1 = <&pinctrl_i2c1_gpio>;
+	scl-gpios = <&gpio5 14 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio5 15 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "okay";
+
+	sensor0: temperature-sensor-eeprom@1b {
+		compatible = "nxp,se97", "jedec,jc-42.4-temp";
+		reg = <0x1b>;
+	};
+
+	pca9450: pmic@25 {
+		compatible = "nxp,pca9450a";
+		reg = <0x25>;
+
+		/* PMIC PCA9450 PMIC_nINT GPIO1_IO08 */
+		pinctrl-0 = <&pinctrl_pmic>;
+		pinctrl-names = "default";
+		interrupt-parent = <&gpio1>;
+		interrupts = <8 IRQ_TYPE_LEVEL_LOW>;
+
+		regulators {
+			/* V_0V85_SOC: 0.85 */
+			buck1_reg: BUCK1 {
+				regulator-name = "BUCK1";
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <850000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <3125>;
+			};
+
+			/* VDD_ARM */
+			buck2_reg: BUCK2 {
+				regulator-name = "BUCK2";
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-boot-on;
+				regulator-always-on;
+				nxp,dvs-run-voltage = <950000>;
+				nxp,dvs-standby-voltage = <850000>;
+				regulator-ramp-delay = <3125>;
+			};
+
+			/* V_0V85_GPU / DRAM / VPU */
+			buck3_reg: BUCK3 {
+				regulator-name = "BUCK3";
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <950000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <3125>;
+			};
+
+			/* VCC3V3 -> VMMC, ... must not be changed */
+			buck4_reg: BUCK4 {
+				regulator-name = "BUCK4";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			/* V_1V8 -> VQMMC, SPI-NOR, ... must not be changed */
+			buck5_reg: BUCK5 {
+				regulator-name = "BUCK5";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			/* V_1V1 -> RAM, ... must not be changed */
+			buck6_reg: BUCK6 {
+				regulator-name = "BUCK6";
+				regulator-min-microvolt = <1100000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			/* V_1V8_SNVS */
+			ldo1_reg: LDO1 {
+				regulator-name = "LDO1";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			/* V_0V8_SNVS */
+			ldo2_reg: LDO2 {
+				regulator-name = "LDO2";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <850000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			/* V_1V8_ANA */
+			ldo3_reg: LDO3 {
+				regulator-name = "LDO3";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			/* V_0V9_MIPI */
+			ldo4_reg: LDO4 {
+				regulator-name = "LDO4";
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <900000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			/* VCC SD IO - switched using SD2 VSELECT */
+			ldo5_reg: LDO5 {
+				regulator-name = "LDO5";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+			};
+		};
+	};
+
+
+	pcf85063: rtc@51 {
+		compatible = "nxp,pcf85063a";
+		reg = <0x51>;
+		quartz-load-femtofarads = <7000>;
+	};
+
+	eeprom1: eeprom@53 {
+		compatible = "nxp,se97b", "atmel,24c02";
+		read-only;
+		reg = <0x53>;
+		pagesize = <16>;
+	};
+
+	eeprom0: eeprom@57 {
+		compatible = "atmel,24c64";
+		reg = <0x57>;
+		pagesize = <32>;
+	};
+};
+
+&pcie_phy {
+	fsl,refclk-pad-mode = <IMX8_PCIE_REFCLK_PAD_INPUT>;
+	fsl,clkreq-unsupported;
+};
+
+&usdhc3 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+	bus-width = <8>;
+	non-removable;
+	no-sd;
+	no-sdio;
+	vmmc-supply = <&reg_vcc3v3>;
+	vqmmc-supply = <&reg_vcc1v8>;
+	status = "okay";
+};
+
+/*
+ * Attention:
+ * wdog reset is routed to PMIC, PMIC must be preconfigured to force POR
+ * without LDO for SNVS. GPIO1_IO02 must not be used as GPIO.
+ */
+&wdog1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog>;
+	fsl,ext-reset-output;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_flexspi: flexspigrp {
+		fsl,pins = <MX8MM_IOMUXC_NAND_ALE_QSPI_A_SCLK		0x82>,
+			   <MX8MM_IOMUXC_NAND_CE0_B_QSPI_A_SS0_B	0x82>,
+			   <MX8MM_IOMUXC_NAND_DATA00_QSPI_A_DATA0	0x82>,
+			   <MX8MM_IOMUXC_NAND_DATA01_QSPI_A_DATA1	0x82>,
+			   <MX8MM_IOMUXC_NAND_DATA02_QSPI_A_DATA2	0x82>,
+			   <MX8MM_IOMUXC_NAND_DATA03_QSPI_A_DATA3	0x82>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL		0x40000004>,
+			   <MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA		0x40000004>;
+	};
+
+	pinctrl_i2c1_gpio: i2c1gpiogrp {
+		fsl,pins = <MX8MM_IOMUXC_I2C1_SCL_GPIO5_IO14		0x40000004>,
+			   <MX8MM_IOMUXC_I2C1_SDA_GPIO5_IO15		0x40000004>;
+	};
+
+	pinctrl_pmic: pmicgrp {
+		fsl,pins = <MX8MM_IOMUXC_GPIO1_IO08_GPIO1_IO8		0x94>;
+	};
+
+	pinctrl_reg_usdhc2_vmmc: regusdhc2vmmcgrp {
+		fsl,pins = <MX8MM_IOMUXC_SD2_RESET_B_GPIO2_IO19		0x84>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK		0x1d4>,
+			   <MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD		0x1d2>,
+			   <MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0	0x1d4>,
+			   <MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1	0x1d4>,
+			   <MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2	0x1d4>,
+			   <MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3	0x1d4>,
+			   <MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4		0x1d4>,
+			   <MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5	0x1d4>,
+			   <MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6	0x1d4>,
+			   <MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7		0x1d4>,
+			   <MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE	0x84>,
+			   /* option USDHC3_RESET_B not defined, only in RM */
+			   <MX8MM_IOMUXC_NAND_READY_B_GPIO3_IO16	0x84>;
+	};
+
+	pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
+		fsl,pins = <MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK		0x1d2>,
+			   <MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD		0x1d2>,
+			   <MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0	0x1d4>,
+			   <MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1	0x1d4>,
+			   <MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2	0x1d4>,
+			   <MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3	0x1d4>,
+			   <MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4		0x1d4>,
+			   <MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5	0x1d4>,
+			   <MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6	0x1d4>,
+			   <MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7		0x1d4>,
+			   <MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE	0x84>,
+			   /* option USDHC3_RESET_B not defined, only in RM */
+			   <MX8MM_IOMUXC_NAND_READY_B_GPIO3_IO16	0x84>;
+	};
+
+	pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
+		fsl,pins = <MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK		0x1d6>,
+			   <MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD		0x1d2>,
+			   <MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0	0x1d4>,
+			   <MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1	0x1d4>,
+			   <MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2	0x1d4>,
+			   <MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3	0x1d4>,
+			   <MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4		0x1d4>,
+			   <MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5	0x1d4>,
+			   <MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6	0x1d4>,
+			   <MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7		0x1d4>,
+			   <MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE	0x84>,
+			   /* option USDHC3_RESET_B not defined, only in RM */
+			   <MX8MM_IOMUXC_NAND_READY_B_GPIO3_IO16	0x84>;
+	};
+
+	pinctrl_wdog: wdoggrp {
+		fsl,pins = <MX8MM_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B	0x84>;
+	};
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-var-som-symphony.dts b/arch/arm64/boot/dts/freescale/imx8mm-var-som-symphony.dts
index ac1fe1530ac7..d643381417f1 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-var-som-symphony.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mm-var-som-symphony.dts
@@ -36,19 +36,19 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		back {
+		key-back {
 			label = "Back";
 			gpios = <&pca9534 1 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_BACK>;
 		};
 
-		home {
+		key-home {
 			label = "Home";
 			gpios = <&pca9534 2 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_HOME>;
 		};
 
-		menu {
+		key-menu {
 			label = "Menu";
 			gpios = <&pca9534 3 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_MENU>;
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-var-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-var-som.dtsi
index 1dc9d187601c..a0bd540f27d3 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-var-som.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm-var-som.dtsi
@@ -89,12 +89,12 @@
 		pendown-gpio = <&gpio1 3 GPIO_ACTIVE_LOW>;
 
 		ti,x-min = /bits/ 16 <125>;
-		touchscreen-size-x = /bits/ 16 <4008>;
+		touchscreen-size-x = <4008>;
 		ti,y-min = /bits/ 16 <282>;
-		touchscreen-size-y = /bits/ 16 <3864>;
+		touchscreen-size-y = <3864>;
 		ti,x-plate-ohms = /bits/ 16 <180>;
-		touchscreen-max-pressure = /bits/ 16 <255>;
-		touchscreen-average-samples = /bits/ 16 <10>;
+		touchscreen-max-pressure = <255>;
+		touchscreen-average-samples = <10>;
 		ti,debounce-tol = /bits/ 16 <3>;
 		ti,debounce-rep = /bits/ 16 <1>;
 		ti,settle-delay-usec = /bits/ 16 <150>;
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw700x.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw700x.dtsi
index 00f86cada30d..66a0d103c90f 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw700x.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw700x.dtsi
@@ -16,13 +16,13 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		user-pb {
+		key-user-pb {
 			label = "user_pb";
 			gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
 			linux,code = <BTN_0>;
 		};
 
-		user-pb1x {
+		key-user-pb1x {
 			label = "user_pb1x";
 			linux,code = <BTN_1>;
 			interrupt-parent = <&gsc>;
@@ -36,14 +36,14 @@
 			interrupts = <1>;
 		};
 
-		eeprom-wp {
+		key-eeprom-wp {
 			label = "eeprom_wp";
 			linux,code = <BTN_3>;
 			interrupt-parent = <&gsc>;
 			interrupts = <2>;
 		};
 
-		tamper {
+		key-tamper {
 			label = "tamper";
 			linux,code = <BTN_4>;
 			interrupt-parent = <&gsc>;
@@ -286,8 +286,8 @@
 				regulator-name = "buck1";
 				regulator-min-microvolt = <800000>;
 				regulator-max-microvolt = <1000000>;
-				regulator-min-microamp  = <3800000>;
-				regulator-max-microamp  = <6800000>;
+				regulator-min-microamp = <3800000>;
+				regulator-max-microamp = <6800000>;
 				regulator-boot-on;
 				regulator-always-on;
 			};
@@ -297,8 +297,8 @@
 				regulator-name = "buck2";
 				regulator-min-microvolt = <800000>;
 				regulator-max-microvolt = <900000>;
-				regulator-min-microamp  = <2200000>;
-				regulator-max-microamp  = <5200000>;
+				regulator-min-microamp = <2200000>;
+				regulator-max-microamp = <5200000>;
 				regulator-boot-on;
 				regulator-always-on;
 			};
@@ -308,8 +308,8 @@
 				regulator-name = "buck3";
 				regulator-min-microvolt = <800000>;
 				regulator-max-microvolt = <1000000>;
-				regulator-min-microamp  = <3800000>;
-				regulator-max-microamp  = <6800000>;
+				regulator-min-microamp = <3800000>;
+				regulator-max-microamp = <6800000>;
 				regulator-always-on;
 			};
 
@@ -318,8 +318,8 @@
 				regulator-name = "buck4";
 				regulator-min-microvolt = <1800000>;
 				regulator-max-microvolt = <1800000>;
-				regulator-min-microamp  = <2200000>;
-				regulator-max-microamp  = <5200000>;
+				regulator-min-microamp = <2200000>;
+				regulator-max-microamp = <5200000>;
 				regulator-boot-on;
 				regulator-always-on;
 			};
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx.dtsi
index 28012279f6f6..c557dbf4dcd6 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw71xx.dtsi
@@ -5,6 +5,7 @@
 
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/leds/common.h>
+#include <dt-bindings/phy/phy-imx8-pcie.h>
 
 / {
 	aliases {
@@ -33,6 +34,12 @@
 		};
 	};
 
+	pcie0_refclk: pcie0-refclk {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <100000000>;
+	};
+
 	pps {
 		compatible = "pps-gpio";
 		pinctrl-names = "default";
@@ -61,6 +68,20 @@
 	status = "okay";
 };
 
+&gpio1 {
+	gpio-line-names = "", "", "", "", "", "", "pci_usb_sel", "dio0",
+		"", "dio1", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "";
+};
+
+&gpio4 {
+	gpio-line-names = "", "", "", "dio2", "dio3", "", "", "pci_wdis#",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "";
+};
+
 &i2c2 {
 	clock-frequency = <400000>;
 	pinctrl-names = "default";
@@ -87,6 +108,29 @@
 	status = "okay";
 };
 
+&pcie_phy {
+	fsl,refclk-pad-mode = <IMX8_PCIE_REFCLK_PAD_INPUT>;
+	fsl,clkreq-unsupported;
+	clocks = <&pcie0_refclk>;
+	clock-names = "ref";
+	status = "okay";
+};
+
+&pcie0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pcie0>;
+	reset-gpio = <&gpio4 6 GPIO_ACTIVE_LOW>;
+	clocks = <&clk IMX8MM_CLK_PCIE1_ROOT>, <&clk IMX8MM_CLK_PCIE1_AUX>,
+		 <&pcie0_refclk>;
+	clock-names = "pcie", "pcie_aux", "pcie_bus";
+	assigned-clocks = <&clk IMX8MM_CLK_PCIE1_AUX>,
+			  <&clk IMX8MM_CLK_PCIE1_CTRL>;
+	assigned-clock-rates = <10000000>, <250000000>;
+	assigned-clock-parents = <&clk IMX8MM_SYS_PLL2_50M>,
+				 <&clk IMX8MM_SYS_PLL2_250M>;
+	status = "okay";
+};
+
 /* GPS */
 &uart1 {
 	pinctrl-names = "default";
@@ -103,12 +147,14 @@
 
 &usbotg1 {
 	dr_mode = "otg";
+	over-current-active-low;
 	vbus-supply = <&reg_usb_otg1_vbus>;
 	status = "okay";
 };
 
 &usbotg2 {
 	dr_mode = "host";
+	disable-over-current;
 	status = "okay";
 };
 
@@ -148,6 +194,12 @@
 		>;
 	};
 
+	pinctrl_pcie0: pcie0grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI1_RXD4_GPIO4_IO6	0x41
+		>;
+	};
+
 	pinctrl_pps: ppsgrp {
 		fsl,pins = <
 			MX8MM_IOMUXC_GPIO1_IO15_GPIO1_IO15	0x41
@@ -166,7 +218,7 @@
 		fsl,pins = <
 			MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK	0xd6
 			MX8MM_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI	0xd6
-			MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK	0xd6
+			MX8MM_IOMUXC_ECSPI2_MISO_ECSPI2_MISO	0xd6
 			MX8MM_IOMUXC_ECSPI2_SS0_GPIO5_IO13	0xd6
 		>;
 	};
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx-0x-imx219.dts b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx-0x-imx219.dts
new file mode 100644
index 000000000000..4eaf8aabcbff
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx-0x-imx219.dts
@@ -0,0 +1,93 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2022 Gateworks Corporation
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+
+#include "imx8mm-pinfunc.h"
+
+/dts-v1/;
+/plugin/;
+
+&{/} {
+	compatible = "gw,imx8mm-gw72xx-0x", "fsl,imx8mm";
+
+	reg_cam: regulator-cam {
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_cam>;
+		compatible = "regulator-fixed";
+		regulator-name = "reg_cam";
+		gpio = <&gpio1 1 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	cam24m: cam24m {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <24000000>;
+		clock-output-names = "cam24m";
+	};
+};
+
+&csi {
+	status = "okay";
+};
+
+&i2c3 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	imx219: sensor@10 {
+		compatible = "sony,imx219";
+		reg = <0x10>;
+		clocks = <&cam24m>;
+		VDIG-supply = <&reg_cam>;
+
+		port {
+			/* MIPI CSI-2 bus endpoint */
+			imx219_to_mipi_csi2: endpoint {
+				remote-endpoint = <&imx8mm_mipi_csi_in>;
+				clock-lanes = <0>;
+				data-lanes = <1 2>;
+				link-frequencies = /bits/ 64 <456000000>;
+			};
+		};
+	};
+};
+
+&mipi_csi {
+	status = "okay";
+
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+
+			imx8mm_mipi_csi_in: endpoint {
+				remote-endpoint = <&imx219_to_mipi_csi2>;
+				data-lanes = <1 2>;
+			};
+		};
+
+		port@1 {
+			reg = <1>;
+
+			imx8mm_mipi_csi_out: endpoint {
+				remote-endpoint = <&csi_in>;
+			};
+		};
+	};
+};
+
+&iomuxc {
+	pinctrl_reg_cam: regcamgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO01_GPIO1_IO1	0x41
+		>;
+	};
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx-0x-rs232-rts.dts b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx-0x-rs232-rts.dts
new file mode 100644
index 000000000000..3ea73a6886ff
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx-0x-rs232-rts.dts
@@ -0,0 +1,53 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2022 Gateworks Corporation
+ *
+ * GW72xx RS232 with RTS/CTS hardware flow control:
+ *  - GPIO4_0 rs485_en needs to be driven low (in-active)
+ *  - UART4_TX becomes RTS
+ *  - UART4_RX becomes CTS
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+
+#include "imx8mm-pinfunc.h"
+
+/dts-v1/;
+/plugin/;
+
+&{/} {
+	compatible = "gw,imx8mm-gw72xx-0x";
+};
+
+&gpio4 {
+	rs485_en {
+		gpio-hog;
+		gpios = <0 GPIO_ACTIVE_HIGH>;
+		output-low;
+		line-name = "rs485_en";
+	};
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	rts-gpios = <&gpio5 29 GPIO_ACTIVE_LOW>;
+	cts-gpios = <&gpio5 28 GPIO_ACTIVE_LOW>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&uart4 {
+	status = "disabled";
+};
+
+&iomuxc {
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_UART2_RXD_UART2_DCE_RX     0x140
+			MX8MM_IOMUXC_UART2_TXD_UART2_DCE_TX     0x140
+			MX8MM_IOMUXC_UART4_TXD_GPIO5_IO29	0x140
+			MX8MM_IOMUXC_UART4_RXD_GPIO5_IO28	0x140
+		>;
+	};
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx-0x-rs422.dts b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx-0x-rs422.dts
new file mode 100644
index 000000000000..c3cd9f2b0db3
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx-0x-rs422.dts
@@ -0,0 +1,61 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2022 Gateworks Corporation
+ *
+ * GW72xx RS422 (RS485 full duplex):
+ *  - GPIO1_0 rs485_term selects on-chip termination
+ *  - GPIO4_0 rs485_en needs to be driven high (active)
+ *  - GPIO4_2 rs485_hd needs to be driven low (in-active)
+ *  - UART4_TX is DE for RS485 transmitter
+ *  - RS485_EN needs to be pulled high
+ *  - RS485_HALF needs to be low
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+
+#include "imx8mm-pinfunc.h"
+
+/dts-v1/;
+/plugin/;
+
+&{/} {
+	compatible = "gw,imx8mm-gw72xx-0x";
+};
+
+&gpio4 {
+	rs485_en {
+		gpio-hog;
+		gpios = <0 GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "rs485_en";
+	};
+
+	rs485_hd {
+		gpio-hog;
+		gpios = <2 GPIO_ACTIVE_HIGH>;
+		output-low;
+		line-name = "rs485_hd";
+	};
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	rts-gpios = <&gpio5 29 GPIO_ACTIVE_HIGH>;
+	linux,rs485-enabled-at-boot-time;
+	status = "okay";
+};
+
+&uart4 {
+	status = "disabled";
+};
+
+&iomuxc {
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_UART2_RXD_UART2_DCE_RX     0x140
+			MX8MM_IOMUXC_UART2_TXD_UART2_DCE_TX     0x140
+			MX8MM_IOMUXC_UART4_TXD_GPIO5_IO29	0x140
+		>;
+	};
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx-0x-rs485.dts b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx-0x-rs485.dts
new file mode 100644
index 000000000000..cc0a287226ab
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx-0x-rs485.dts
@@ -0,0 +1,61 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2022 Gateworks Corporation
+ *
+ * GW72xx RS485 HD:
+ *  - GPIO1_0 rs485_term selects on-chip termination
+ *  - GPIO4_0 rs485_en needs to be driven high (active)
+ *  - GPIO4_2 rs485_hd needs to be driven high (active)
+ *  - UART4_TX is DE for RS485 transmitter
+ *  - RS485_EN needs to be pulled high
+ *  - RS485_HALF needs to be pulled high
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+
+#include "imx8mm-pinfunc.h"
+
+/dts-v1/;
+/plugin/;
+
+&{/} {
+	compatible = "gw,imx8mm-gw72xx-0x";
+};
+
+&gpio4 {
+	rs485_en {
+		gpio-hog;
+		gpios = <0 GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "rs485_en";
+	};
+
+	rs485_hd {
+		gpio-hog;
+		gpios = <2 GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "rs485_hd";
+	};
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	rts-gpios = <&gpio5 29 GPIO_ACTIVE_HIGH>;
+	linux,rs485-enabled-at-boot-time;
+	status = "okay";
+};
+
+&uart4 {
+	status = "disabled";
+};
+
+&iomuxc {
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_UART2_RXD_UART2_DCE_RX     0x140
+			MX8MM_IOMUXC_UART2_TXD_UART2_DCE_TX     0x140
+			MX8MM_IOMUXC_UART4_TXD_GPIO5_IO29	0x140
+		>;
+	};
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx-0x.dts b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx-0x.dts
index b1e7540f0281..641be3af989d 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx-0x.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx-0x.dts
@@ -17,4 +17,3 @@
 		stdout-path = &uart2;
 	};
 };
-
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx.dtsi
index 27afa46a253a..41d0de6a7027 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw72xx.dtsi
@@ -5,9 +5,11 @@
 
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/leds/common.h>
+#include <dt-bindings/phy/phy-imx8-pcie.h>
 
 / {
 	aliases {
+		ethernet1 = &eth1;
 		usb0 = &usbotg1;
 		usb1 = &usbotg2;
 	};
@@ -33,6 +35,12 @@
 		};
 	};
 
+	pcie0_refclk: pcie0-refclk {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <100000000>;
+	};
+
 	pps {
 		compatible = "pps-gpio";
 		pinctrl-names = "default";
@@ -80,6 +88,22 @@
 	status = "okay";
 };
 
+&gpio1 {
+	gpio-line-names = "rs485_term", "mipi_gpio4", "", "",
+		"", "", "pci_usb_sel", "dio0",
+		"", "dio1", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "";
+};
+
+&gpio4 {
+	gpio-line-names = "rs485_en", "mipi_gpio3", "rs485_hd", "mipi_gpio2",
+		"mipi_gpio1", "", "", "pci_wdis#",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "";
+};
+
 &i2c2 {
 	clock-frequency = <400000>;
 	pinctrl-names = "default";
@@ -106,6 +130,55 @@
 	status = "okay";
 };
 
+&pcie_phy {
+	fsl,refclk-pad-mode = <IMX8_PCIE_REFCLK_PAD_INPUT>;
+	fsl,clkreq-unsupported;
+	clocks = <&pcie0_refclk>;
+	clock-names = "ref";
+	status = "okay";
+};
+
+&pcie0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pcie0>;
+	reset-gpio = <&gpio4 6 GPIO_ACTIVE_LOW>;
+	clocks = <&clk IMX8MM_CLK_PCIE1_ROOT>, <&clk IMX8MM_CLK_PCIE1_AUX>,
+		 <&pcie0_refclk>;
+	clock-names = "pcie", "pcie_aux", "pcie_bus";
+	assigned-clocks = <&clk IMX8MM_CLK_PCIE1_AUX>,
+			  <&clk IMX8MM_CLK_PCIE1_CTRL>;
+	assigned-clock-rates = <10000000>, <250000000>;
+	assigned-clock-parents = <&clk IMX8MM_SYS_PLL2_50M>,
+				 <&clk IMX8MM_SYS_PLL2_250M>;
+	status = "okay";
+
+	pcie@0,0 {
+		reg = <0x0000 0 0 0 0>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pcie@1,0 {
+			reg = <0x0000 0 0 0 0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			pcie@2,3 {
+				reg = <0x1800 0 0 0 0>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eth1: pcie@5,0 {
+					reg = <0x0000 0 0 0 0>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					local-mac-address = [00 00 00 00 00 00];
+				};
+			};
+		};
+	};
+};
+
 /* off-board header */
 &sai3 {
 	pinctrl-names = "default";
@@ -139,12 +212,14 @@
 
 &usbotg1 {
 	dr_mode = "otg";
+	over-current-active-low;
 	vbus-supply = <&reg_usb_otg1_vbus>;
 	status = "okay";
 };
 
 &usbotg2 {
 	dr_mode = "host";
+	disable-over-current;
 	vbus-supply = <&reg_usb_otg2_vbus>;
 	status = "okay";
 };
@@ -198,6 +273,12 @@
 		>;
 	};
 
+	pinctrl_pcie0: pcie0grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI1_RXD4_GPIO4_IO6	0x41
+		>;
+	};
+
 	pinctrl_pps: ppsgrp {
 		fsl,pins = <
 			MX8MM_IOMUXC_GPIO1_IO15_GPIO1_IO15	0x41
@@ -231,7 +312,7 @@
 		fsl,pins = <
 			MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK	0xd6
 			MX8MM_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI	0xd6
-			MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK	0xd6
+			MX8MM_IOMUXC_ECSPI2_MISO_ECSPI2_MISO	0xd6
 			MX8MM_IOMUXC_ECSPI2_SS0_GPIO5_IO13	0xd6
 		>;
 	};
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx-0x-imx219.dts b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx-0x-imx219.dts
new file mode 100644
index 000000000000..f3ece4b7fbbd
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx-0x-imx219.dts
@@ -0,0 +1,93 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2022 Gateworks Corporation
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+
+#include "imx8mm-pinfunc.h"
+
+/dts-v1/;
+/plugin/;
+
+&{/} {
+	compatible = "gw,imx8mm-gw73xx-0x", "fsl,imx8mm";
+
+	reg_cam: regulator-cam {
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_cam>;
+		compatible = "regulator-fixed";
+		regulator-name = "reg_cam";
+		gpio = <&gpio1 1 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	cam24m: cam24m {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <24000000>;
+		clock-output-names = "cam24m";
+	};
+};
+
+&csi {
+	status = "okay";
+};
+
+&i2c3 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	imx219: sensor@10 {
+		compatible = "sony,imx219";
+		reg = <0x10>;
+		clocks = <&cam24m>;
+		VDIG-supply = <&reg_cam>;
+
+		port {
+			/* MIPI CSI-2 bus endpoint */
+			imx219_to_mipi_csi2: endpoint {
+				remote-endpoint = <&imx8mm_mipi_csi_in>;
+				clock-lanes = <0>;
+				data-lanes = <1 2>;
+				link-frequencies = /bits/ 64 <456000000>;
+			};
+		};
+	};
+};
+
+&mipi_csi {
+	status = "okay";
+
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+
+			imx8mm_mipi_csi_in: endpoint {
+				remote-endpoint = <&imx219_to_mipi_csi2>;
+				data-lanes = <1 2>;
+			};
+		};
+
+		port@1 {
+			reg = <1>;
+
+			imx8mm_mipi_csi_out: endpoint {
+				remote-endpoint = <&csi_in>;
+			};
+		};
+	};
+};
+
+&iomuxc {
+	pinctrl_reg_cam: regcamgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO01_GPIO1_IO1	0x41
+		>;
+	};
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx-0x-rs232-rts.dts b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx-0x-rs232-rts.dts
new file mode 100644
index 000000000000..2fa635e1c1a8
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx-0x-rs232-rts.dts
@@ -0,0 +1,53 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2022 Gateworks Corporation
+ *
+ * GW73xx RS232 with RTS/CTS hardware flow control:
+ *  - GPIO4_0 rs485_en needs to be driven low (in-active)
+ *  - UART4_TX becomes RTS
+ *  - UART4_RX becomes CTS
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+
+#include "imx8mm-pinfunc.h"
+
+/dts-v1/;
+/plugin/;
+
+&{/} {
+	compatible = "gw,imx8mm-gw73xx-0x";
+};
+
+&gpio4 {
+	rs485_en {
+		gpio-hog;
+		gpios = <0 GPIO_ACTIVE_HIGH>;
+		output-low;
+		line-name = "rs485_en";
+	};
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	rts-gpios = <&gpio5 29 GPIO_ACTIVE_LOW>;
+	cts-gpios = <&gpio5 28 GPIO_ACTIVE_LOW>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&uart4 {
+	status = "disabled";
+};
+
+&iomuxc {
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_UART2_RXD_UART2_DCE_RX     0x140
+			MX8MM_IOMUXC_UART2_TXD_UART2_DCE_TX     0x140
+			MX8MM_IOMUXC_UART4_TXD_GPIO5_IO29	0x140
+			MX8MM_IOMUXC_UART4_RXD_GPIO5_IO28	0x140
+		>;
+	};
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx-0x-rs422.dts b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx-0x-rs422.dts
new file mode 100644
index 000000000000..3e6404340d52
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx-0x-rs422.dts
@@ -0,0 +1,61 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2021 Gateworks Corporation
+ *
+ * GW73xx RS422 (RS485 full duplex):
+ *  - GPIO1_0 rs485_term selects on-chip termination
+ *  - GPIO4_0 rs485_en needs to be driven high (active)
+ *  - GPIO4_2 rs485_hd needs to be driven low (in-active)
+ *  - UART4_TX is DE for RS485 transmitter
+ *  - RS485_EN needs to be pulled high
+ *  - RS485_HALF needs to be low
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+
+#include "imx8mm-pinfunc.h"
+
+/dts-v1/;
+/plugin/;
+
+&{/} {
+	compatible = "gw,imx8mm-gw73xx-0x";
+};
+
+&gpio4 {
+	rs485_en {
+		gpio-hog;
+		gpios = <0 GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "rs485_en";
+	};
+
+	rs485_hd {
+		gpio-hog;
+		gpios = <2 GPIO_ACTIVE_HIGH>;
+		output-low;
+		line-name = "rs485_hd";
+	};
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	rts-gpios = <&gpio5 29 GPIO_ACTIVE_HIGH>;
+	linux,rs485-enabled-at-boot-time;
+	status = "okay";
+};
+
+&uart4 {
+	status = "disabled";
+};
+
+&iomuxc {
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_UART2_RXD_UART2_DCE_RX     0x140
+			MX8MM_IOMUXC_UART2_TXD_UART2_DCE_TX     0x140
+			MX8MM_IOMUXC_UART4_TXD_GPIO5_IO29	0x140
+		>;
+	};
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx-0x-rs485.dts b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx-0x-rs485.dts
new file mode 100644
index 000000000000..2c71ab9854cb
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx-0x-rs485.dts
@@ -0,0 +1,61 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2021 Gateworks Corporation
+ *
+ * GW73xx RS485 HD:
+ *  - GPIO1_0 rs485_term selects on-chip termination
+ *  - GPIO4_0 rs485_en needs to be driven high (active)
+ *  - GPIO4_2 rs485_hd needs to be driven high (active)
+ *  - UART4_TX is DE for RS485 transmitter
+ *  - RS485_EN needs to be pulled high
+ *  - RS485_HALF needs to be pulled high
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+
+#include "imx8mm-pinfunc.h"
+
+/dts-v1/;
+/plugin/;
+
+&{/} {
+	compatible = "gw,imx8mm-gw73xx-0x";
+};
+
+&gpio4 {
+	rs485_en {
+		gpio-hog;
+		gpios = <0 GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "rs485_en";
+	};
+
+	rs485_hd {
+		gpio-hog;
+		gpios = <2 GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "rs485_hd";
+	};
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	rts-gpios = <&gpio5 29 GPIO_ACTIVE_HIGH>;
+	linux,rs485-enabled-at-boot-time;
+	status = "okay";
+};
+
+&uart4 {
+	status = "disabled";
+};
+
+&iomuxc {
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_UART2_RXD_UART2_DCE_RX     0x140
+			MX8MM_IOMUXC_UART2_TXD_UART2_DCE_TX     0x140
+			MX8MM_IOMUXC_UART4_TXD_GPIO5_IO29	0x140
+		>;
+	};
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx.dtsi
index a59e849c7be2..244ef8d6cc68 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw73xx.dtsi
@@ -5,9 +5,11 @@
 
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/leds/common.h>
+#include <dt-bindings/phy/phy-imx8-pcie.h>
 
 / {
 	aliases {
+		ethernet1 = &eth1;
 		usb0 = &usbotg1;
 		usb1 = &usbotg2;
 	};
@@ -33,6 +35,12 @@
 		};
 	};
 
+	pcie0_refclk: pcie0-refclk {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <100000000>;
+	};
+
 	pps {
 		compatible = "pps-gpio";
 		pinctrl-names = "default";
@@ -100,6 +108,22 @@
 	status = "okay";
 };
 
+&gpio1 {
+	gpio-line-names = "rs485_term", "mipi_gpio4", "", "",
+		"", "", "pci_usb_sel", "dio0",
+		"", "dio1", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "";
+};
+
+&gpio4 {
+	gpio-line-names = "rs485_en", "mipi_gpio3", "rs485_hd", "mipi_gpio2",
+		"mipi_gpio1", "", "", "pci_wdis#",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "";
+};
+
 &i2c2 {
 	clock-frequency = <400000>;
 	pinctrl-names = "default";
@@ -126,6 +150,55 @@
 	status = "okay";
 };
 
+&pcie_phy {
+	fsl,refclk-pad-mode = <IMX8_PCIE_REFCLK_PAD_INPUT>;
+	fsl,clkreq-unsupported;
+	clocks = <&pcie0_refclk>;
+	clock-names = "ref";
+	status = "okay";
+};
+
+&pcie0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pcie0>;
+	reset-gpio = <&gpio4 6 GPIO_ACTIVE_LOW>;
+	clocks = <&clk IMX8MM_CLK_PCIE1_ROOT>, <&clk IMX8MM_CLK_PCIE1_AUX>,
+		 <&pcie0_refclk>;
+	clock-names = "pcie", "pcie_aux", "pcie_bus";
+	assigned-clocks = <&clk IMX8MM_CLK_PCIE1_AUX>,
+			  <&clk IMX8MM_CLK_PCIE1_CTRL>;
+	assigned-clock-rates = <10000000>, <250000000>;
+	assigned-clock-parents = <&clk IMX8MM_SYS_PLL2_50M>,
+				 <&clk IMX8MM_SYS_PLL2_250M>;
+	status = "okay";
+
+	pcie@0,0 {
+		reg = <0x0000 0 0 0 0>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pcie@1,0 {
+			reg = <0x0000 0 0 0 0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			pcie@2,4 {
+				reg = <0x2000 0 0 0 0>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				eth1: pcie@6,0 {
+					reg = <0x0000 0 0 0 0>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					local-mac-address = [00 00 00 00 00 00];
+				};
+			};
+		};
+	};
+};
+
 /* off-board header */
 &sai3 {
 	pinctrl-names = "default";
@@ -149,6 +222,7 @@
 	pinctrl-0 = <&pinctrl_uart3>, <&pinctrl_bten>;
 	cts-gpios = <&gpio5 8 GPIO_ACTIVE_LOW>;
 	rts-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
+	uart-has-rtscts;
 	status = "okay";
 
 	bluetooth {
@@ -166,12 +240,14 @@
 
 &usbotg1 {
 	dr_mode = "otg";
+	over-current-active-low;
 	vbus-supply = <&reg_usb_otg1_vbus>;
 	status = "okay";
 };
 
 &usbotg2 {
 	dr_mode = "host";
+	disable-over-current;
 	vbus-supply = <&reg_usb_otg2_vbus>;
 	status = "okay";
 };
@@ -241,6 +317,12 @@
 		>;
 	};
 
+	pinctrl_pcie0: pcie0grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI1_RXD4_GPIO4_IO6	0x41
+		>;
+	};
+
 	pinctrl_pps: ppsgrp {
 		fsl,pins = <
 			MX8MM_IOMUXC_GPIO1_IO15_GPIO1_IO15	0x41
@@ -280,7 +362,7 @@
 		fsl,pins = <
 			MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK	0xd6
 			MX8MM_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI	0xd6
-			MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK	0xd6
+			MX8MM_IOMUXC_ECSPI2_MISO_ECSPI2_MISO	0xd6
 			MX8MM_IOMUXC_ECSPI2_SS0_GPIO5_IO13	0xd6
 		>;
 	};
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw7901.dts b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw7901.dts
index 21c546c4628d..d3ee6fc4baab 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw7901.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw7901.dts
@@ -8,6 +8,7 @@
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/linux-event-codes.h>
 #include <dt-bindings/leds/common.h>
+#include <dt-bindings/phy/phy-imx8-pcie.h>
 
 #include "imx8mm.dtsi"
 
@@ -37,13 +38,13 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		user-pb {
+		key-user-pb {
 			label = "user_pb";
 			gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
 			linux,code = <BTN_0>;
 		};
 
-		user-pb1x {
+		key-user-pb1x {
 			label = "user_pb1x";
 			linux,code = <BTN_1>;
 			interrupt-parent = <&gsc>;
@@ -57,14 +58,14 @@
 			interrupts = <1>;
 		};
 
-		eeprom-wp {
+		key-eeprom-wp {
 			label = "eeprom_wp";
 			linux,code = <BTN_3>;
 			interrupt-parent = <&gsc>;
 			interrupts = <2>;
 		};
 
-		tamper {
+		key-tamper {
 			label = "tamper";
 			linux,code = <BTN_4>;
 			interrupt-parent = <&gsc>;
@@ -179,6 +180,12 @@
 		};
 	};
 
+	pcie0_refclk: pcie0-refclk {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <100000000>;
+	};
+
 	reg_3p3v: regulator-3p3v {
 		compatible = "regulator-fixed";
 		regulator-name = "3P3V";
@@ -286,6 +293,29 @@
 	};
 };
 
+&gpio1 {
+	gpio-line-names = "uart1_rs422#", "", "", "uart1_rs485#",
+		"", "uart1_rs232#", "dig1_in", "dig1_out",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "";
+};
+
+&gpio4 {
+	gpio-line-names = "", "", "", "",
+		"", "", "uart3_rs232#", "uart3_rs422#",
+		"uart3_rs485#", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "uart4_rs485#", "", "sim1det#", "sim2det#", "";
+};
+
+&gpio5 {
+	gpio-line-names = "", "", "", "dig2_out", "dig2_in", "sim2sel", "", "",
+		"", "", "uart4_rs232#", "", "", "uart4_rs422#", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "";
+};
+
 &gpu_2d {
 	status = "disabled";
 };
@@ -596,24 +626,28 @@
 			lan1: port@0 {
 				reg = <0>;
 				label = "lan1";
+				phy-mode = "internal";
 				local-mac-address = [00 00 00 00 00 00];
 			};
 
 			lan2: port@1 {
 				reg = <1>;
 				label = "lan2";
+				phy-mode = "internal";
 				local-mac-address = [00 00 00 00 00 00];
 			};
 
 			lan3: port@2 {
 				reg = <2>;
 				label = "lan3";
+				phy-mode = "internal";
 				local-mac-address = [00 00 00 00 00 00];
 			};
 
 			lan4: port@3 {
 				reg = <3>;
 				label = "lan4";
+				phy-mode = "internal";
 				local-mac-address = [00 00 00 00 00 00];
 			};
 
@@ -644,6 +678,29 @@
 	status = "okay";
 };
 
+&pcie_phy {
+	fsl,refclk-pad-mode = <IMX8_PCIE_REFCLK_PAD_INPUT>;
+	fsl,clkreq-unsupported;
+	clocks = <&pcie0_refclk>;
+	clock-names = "ref";
+	status = "okay";
+};
+
+&pcie0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pcie0>;
+	reset-gpio = <&gpio5 2 GPIO_ACTIVE_LOW>;
+	clocks = <&clk IMX8MM_CLK_PCIE1_ROOT>, <&clk IMX8MM_CLK_PCIE1_AUX>,
+		 <&pcie0_refclk>;
+	clock-names = "pcie", "pcie_aux", "pcie_bus";
+	assigned-clocks = <&clk IMX8MM_CLK_PCIE1_AUX>,
+			  <&clk IMX8MM_CLK_PCIE1_CTRL>;
+	assigned-clock-rates = <10000000>, <250000000>;
+	assigned-clock-parents = <&clk IMX8MM_SYS_PLL2_50M>,
+				 <&clk IMX8MM_SYS_PLL2_250M>;
+	status = "okay";
+};
+
 &pgc_gpu {
 	status = "disabled";
 };
@@ -664,6 +721,7 @@
 	dtr-gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
 	dsr-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
 	dcd-gpios = <&gpio1 11 GPIO_ACTIVE_LOW>;
+	uart-has-rtscts;
 	status = "okay";
 };
 
@@ -679,6 +737,7 @@
 	pinctrl-0 = <&pinctrl_uart3>, <&pinctrl_uart3_gpio>;
 	cts-gpios = <&gpio4 10 GPIO_ACTIVE_LOW>;
 	rts-gpios = <&gpio4 9 GPIO_ACTIVE_LOW>;
+	uart-has-rtscts;
 	status = "okay";
 };
 
@@ -687,6 +746,7 @@
 	pinctrl-0 = <&pinctrl_uart4>, <&pinctrl_uart4_gpio>;
 	cts-gpios = <&gpio5 11 GPIO_ACTIVE_LOW>;
 	rts-gpios = <&gpio5 12 GPIO_ACTIVE_LOW>;
+	uart-has-rtscts;
 	status = "okay";
 };
 
@@ -820,6 +880,13 @@
 		>;
 	};
 
+	pinctrl_pcie0: pciegrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI3_TXFS_GPIO4_IO31	0x40000041 /* WDIS# */
+			MX8MM_IOMUXC_SAI3_MCLK_GPIO5_IO2	0x41
+		>;
+	};
+
 	pinctrl_pmic: pmicgrp {
 		fsl,pins = <
 			MX8MM_IOMUXC_SAI5_RXC_GPIO3_IO20	0x41
@@ -1028,15 +1095,3 @@
 		>;
 	};
 };
-
-&cpu_alert0 {
-	temperature = <95000>;
-	hysteresis = <2000>;
-	type = "passive";
-};
-
-&cpu_crit0 {
-	temperature = <105000>;
-	hysteresis = <2000>;
-	type = "critical";
-};
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw7902.dts b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw7902.dts
index d52686f4c059..31f4c735fe4f 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw7902.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw7902.dts
@@ -9,6 +9,7 @@
 #include <dt-bindings/input/linux-event-codes.h>
 #include <dt-bindings/leds/common.h>
 #include <dt-bindings/net/ti-dp83867.h>
+#include <dt-bindings/phy/phy-imx8-pcie.h>
 
 #include "imx8mm.dtsi"
 
@@ -17,6 +18,7 @@
 	compatible = "gw,imx8mm-gw7902", "fsl,imx8mm";
 
 	aliases {
+		ethernet1 = &eth1;
 		usb0 = &usbotg1;
 		usb1 = &usbotg2;
 	};
@@ -40,13 +42,13 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		user-pb {
+		key-user-pb {
 			label = "user_pb";
 			gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
 			linux,code = <BTN_0>;
 		};
 
-		user-pb1x {
+		key-user-pb1x {
 			label = "user_pb1x";
 			linux,code = <BTN_1>;
 			interrupt-parent = <&gsc>;
@@ -60,14 +62,14 @@
 			interrupts = <1>;
 		};
 
-		eeprom-wp {
+		key-eeprom-wp {
 			label = "eeprom_wp";
 			linux,code = <BTN_3>;
 			interrupt-parent = <&gsc>;
 			interrupts = <2>;
 		};
 
-		tamper {
+		key-tamper {
 			label = "tamper";
 			linux,code = <BTN_4>;
 			interrupt-parent = <&gsc>;
@@ -128,6 +130,12 @@
 		};
 	};
 
+	pcie0_refclk: pcie0-refclk {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <100000000>;
+	};
+
 	pps {
 		compatible = "pps-gpio";
 		pinctrl-names = "default";
@@ -214,7 +222,6 @@
 		compatible = "microchip,mcp2515";
 		reg = <0>;
 		clocks = <&can20m>;
-		oscillator-frequency = <20000000>;
 		interrupt-parent = <&gpio2>;
 		interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
 		spi-max-frequency = <10000000>;
@@ -252,6 +259,43 @@
 	};
 };
 
+&gpio1 {
+	gpio-line-names = "", "", "", "", "", "", "", "",
+		"", "", "", "", "", "m2_reset", "", "m2_wdis#",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "";
+};
+
+&gpio2 {
+	gpio-line-names = "", "", "", "", "", "", "", "",
+		"uart2_en#", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "";
+};
+
+&gpio3 {
+	gpio-line-names = "", "m2_gdis#", "", "", "", "", "", "m2_off#",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "";
+};
+
+&gpio4 {
+	gpio-line-names = "", "", "", "", "", "", "", "",
+		"", "", "", "amp_gpio3", "amp_gpio2", "", "amp_gpio1", "",
+		"", "", "", "", "amp_gpio4", "app_gpio1", "", "uart1_rs485",
+		"", "uart1_term", "uart1_half", "app_gpio2",
+		"mipi_gpio1", "", "", "";
+};
+
+&gpio5 {
+	gpio-line-names = "", "", "", "mipi_gpio4",
+		"mipi_gpio3", "mipi_gpio2", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "";
+};
+
 &i2c1 {
 	clock-frequency = <100000>;
 	pinctrl-names = "default";
@@ -349,6 +393,13 @@
 				gw,voltage-divider-ohms = <10000 10000>;
 			};
 
+			channel@9c {
+				gw,mode = <2>;
+				reg = <0x9c>;
+				label = "vdd_5p0";
+				gw,voltage-divider-ohms = <10000 10000>;
+			};
+
 			channel@a2 {
 				gw,mode = <2>;
 				reg = <0xa2>;
@@ -547,6 +598,43 @@
 	status = "okay";
 };
 
+&pcie_phy {
+	fsl,refclk-pad-mode = <IMX8_PCIE_REFCLK_PAD_INPUT>;
+	fsl,clkreq-unsupported;
+	clocks = <&pcie0_refclk>;
+	clock-names = "ref";
+	status = "okay";
+};
+
+&pcie0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pcie0>;
+	reset-gpio = <&gpio4 5 GPIO_ACTIVE_LOW>;
+	clocks = <&clk IMX8MM_CLK_PCIE1_ROOT>, <&clk IMX8MM_CLK_PCIE1_AUX>,
+		 <&pcie0_refclk>;
+	clock-names = "pcie", "pcie_aux", "pcie_bus";
+	assigned-clocks = <&clk IMX8MM_CLK_PCIE1_AUX>,
+			  <&clk IMX8MM_CLK_PCIE1_CTRL>;
+	assigned-clock-rates = <10000000>, <250000000>;
+	assigned-clock-parents = <&clk IMX8MM_SYS_PLL2_50M>,
+				 <&clk IMX8MM_SYS_PLL2_250M>;
+	status = "okay";
+
+	pcie@0,0 {
+		reg = <0x0000 0 0 0 0>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		eth1: pcie@1,0 {
+			reg = <0x0000 0 0 0 0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			local-mac-address = [00 00 00 00 00 00];
+		};
+	};
+};
+
 /* off-board header */
 &sai3 {
 	pinctrl-names = "default";
@@ -562,7 +650,8 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart1>, <&pinctrl_uart1_gpio>;
 	rts-gpios = <&gpio4 10 GPIO_ACTIVE_LOW>;
-	cts-gpios = <&gpio4 11 GPIO_ACTIVE_LOW>;
+	cts-gpios = <&gpio4 24 GPIO_ACTIVE_LOW>;
+	uart-has-rtscts;
 	status = "okay";
 };
 
@@ -579,6 +668,7 @@
 	pinctrl-0 = <&pinctrl_uart3>, <&pinctrl_uart3_gpio>;
 	rts-gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
 	cts-gpios = <&gpio2 0 GPIO_ACTIVE_LOW>;
+	uart-has-rtscts;
 	status = "okay";
 
 	bluetooth {
@@ -596,6 +686,7 @@
 	dtr-gpios = <&gpio4 3 GPIO_ACTIVE_LOW>;
 	dsr-gpios = <&gpio4 4 GPIO_ACTIVE_LOW>;
 	dcd-gpios = <&gpio4 6 GPIO_ACTIVE_LOW>;
+	uart-has-rtscts;
 	status = "okay";
 };
 
@@ -647,7 +738,7 @@
 	pinctrl_hog: hoggrp {
 		fsl,pins = <
 			MX8MM_IOMUXC_NAND_CE0_B_GPIO3_IO1	0x40000159 /* M2_GDIS# */
-			MX8MM_IOMUXC_GPIO1_IO13_GPIO1_IO13	0x40000041 /* M2_RST# */
+			MX8MM_IOMUXC_GPIO1_IO13_GPIO1_IO13	0x40000041 /* M2_RESET */
 			MX8MM_IOMUXC_NAND_DATA01_GPIO3_IO7	0x40000119 /* M2_OFF# */
 			MX8MM_IOMUXC_GPIO1_IO15_GPIO1_IO15	0x40000159 /* M2_WDIS# */
 			MX8MM_IOMUXC_SAI1_TXD2_GPIO4_IO14	0x40000041 /* AMP GPIO1 */
@@ -737,6 +828,12 @@
 		>;
 	};
 
+	pinctrl_pcie0: pciegrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI1_RXD3_GPIO4_IO5	0x41
+		>;
+	};
+
 	pinctrl_pmic: pmicgrp {
 		fsl,pins = <
 			MX8MM_IOMUXC_NAND_DATA02_GPIO3_IO8	0x41
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw7903.dts b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw7903.dts
new file mode 100644
index 000000000000..19f6d2943d26
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw7903.dts
@@ -0,0 +1,839 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2022 Gateworks Corporation
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/phy/phy-imx8-pcie.h>
+
+#include "imx8mm.dtsi"
+
+/ {
+	model = "Gateworks Venice GW7903 i.MX8MM board";
+	compatible = "gw,imx8mm-gw7903", "fsl,imx8mm";
+
+	aliases {
+		ethernet0 = &fec1;
+		usb0 = &usbotg1;
+	};
+
+	chosen {
+		stdout-path = &uart2;
+	};
+
+	memory@40000000 {
+		device_type = "memory";
+		reg = <0x0 0x40000000 0 0x80000000>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		key-user-pb {
+			label = "user_pb";
+			gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
+			linux,code = <BTN_0>;
+		};
+
+		key-user-pb1x {
+			label = "user_pb1x";
+			linux,code = <BTN_1>;
+			interrupt-parent = <&gsc>;
+			interrupts = <0>;
+		};
+
+		key-erased {
+			label = "key_erased";
+			linux,code = <BTN_2>;
+			interrupt-parent = <&gsc>;
+			interrupts = <1>;
+		};
+
+		key-eeprom-wp {
+			label = "eeprom_wp";
+			linux,code = <BTN_3>;
+			interrupt-parent = <&gsc>;
+			interrupts = <2>;
+		};
+
+		switch-hold {
+			label = "switch_hold";
+			linux,code = <BTN_5>;
+			interrupt-parent = <&gsc>;
+			interrupts = <7>;
+		};
+	};
+
+	led-controller {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_leds>;
+
+		led-0 {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_RED>;
+			label = "led01_red";
+			gpios = <&gpio5 5 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		led-1 {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_GREEN>;
+			label = "led01_grn";
+			gpios = <&gpio4 30 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		led-2 {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_RED>;
+			label = "led02_red";
+			gpios = <&gpio5 2 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		led-3 {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_GREEN>;
+			label = "led02_grn";
+			gpios = <&gpio1 14 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		led-4 {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_RED>;
+			label = "led03_red";
+			gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		led-5 {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_GREEN>;
+			label = "led03_grn";
+			gpios = <&gpio5 3 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		led-6 {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_RED>;
+			label = "led04_red";
+			gpios = <&gpio4 29 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		led-7 {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_GREEN>;
+			label = "led04_grn";
+			gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		led-8 {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_RED>;
+			label = "led05_red";
+			gpios = <&gpio1 13 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		led-9 {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_GREEN>;
+			label = "led05_grn";
+			gpios = <&gpio4 31 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		led-a {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_RED>;
+			label = "led06_red";
+			gpios = <&gpio5 4 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		led-b {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_GREEN>;
+			label = "led06_grn";
+			gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+	};
+
+	pcie0_refclk: pcie0-refclk {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <100000000>;
+	};
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+};
+
+&A53_0 {
+	cpu-supply = <&buck2>;
+};
+
+&A53_1 {
+	cpu-supply = <&buck2>;
+};
+
+&A53_2 {
+	cpu-supply = <&buck2>;
+};
+
+&A53_3 {
+	cpu-supply = <&buck2>;
+};
+
+&ddrc {
+	operating-points-v2 = <&ddrc_opp_table>;
+
+	ddrc_opp_table: opp-table {
+		compatible = "operating-points-v2";
+
+		opp-25M {
+			opp-hz = /bits/ 64 <25000000>;
+		};
+
+		opp-100M {
+			opp-hz = /bits/ 64 <100000000>;
+		};
+
+		opp-750M {
+			opp-hz = /bits/ 64 <750000000>;
+		};
+	};
+};
+
+&fec1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_fec1>;
+	phy-mode = "rgmii-id";
+	phy-handle = <&ethphy0>;
+	local-mac-address = [00 00 00 00 00 00];
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy0: ethernet-phy@0 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <0>;
+			rx-internal-delay-ps = <2000>;
+			tx-internal-delay-ps = <2500>;
+		};
+	};
+};
+
+&gpio1 {
+	gpio-line-names = "", "", "", "", "", "", "", "",
+		"", "", "rs422_en#", "rs485_en#", "rs232_en#", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "";
+};
+
+&gpio2 {
+	gpio-line-names = "dig2_in", "dig2_out#", "dig2_ctl", "", "", "", "dig1_ctl", "",
+		"dig1_out#", "dig1_in", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "";
+};
+
+&gpio5 {
+	gpio-line-names = "", "", "", "", "", "", "", "sim1_det#",
+		"sim2_det#", "sim2_sel", "", "", "pci_wdis#", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "";
+};
+
+&i2c1 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+
+	gsc: gsc@20 {
+		compatible = "gw,gsc";
+		reg = <0x20>;
+		pinctrl-0 = <&pinctrl_gsc>;
+		interrupt-parent = <&gpio4>;
+		interrupts = <26 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-controller;
+		#interrupt-cells = <1>;
+
+		adc {
+			compatible = "gw,gsc-adc";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			channel@6 {
+				gw,mode = <0>;
+				reg = <0x06>;
+				label = "temp";
+			};
+
+			channel@8 {
+				gw,mode = <1>;
+				reg = <0x08>;
+				label = "vdd_bat";
+			};
+
+			channel@82 {
+				gw,mode = <2>;
+				reg = <0x82>;
+				label = "vin";
+				gw,voltage-divider-ohms = <22100 1000>;
+				gw,voltage-offset-microvolt = <700000>;
+			};
+
+			channel@84 {
+				gw,mode = <2>;
+				reg = <0x84>;
+				label = "vdd_5p0";
+				gw,voltage-divider-ohms = <10000 10000>;
+			};
+
+			channel@86 {
+				gw,mode = <2>;
+				reg = <0x86>;
+				label = "vdd_3p3";
+				gw,voltage-divider-ohms = <10000 10000>;
+			};
+
+			channel@88 {
+				gw,mode = <2>;
+				reg = <0x88>;
+				label = "vdd_0p9";
+			};
+
+			channel@8c {
+				gw,mode = <2>;
+				reg = <0x8c>;
+				label = "vdd_soc";
+			};
+
+			channel@8e {
+				gw,mode = <2>;
+				reg = <0x8e>;
+				label = "vdd_arm";
+			};
+
+			channel@90 {
+				gw,mode = <2>;
+				reg = <0x90>;
+				label = "vdd_1p8";
+			};
+
+			channel@92 {
+				gw,mode = <2>;
+				reg = <0x92>;
+				label = "vdd_dram";
+			};
+
+			channel@a2 {
+				gw,mode = <2>;
+				reg = <0xa2>;
+				label = "vdd_gsc";
+				gw,voltage-divider-ohms = <10000 10000>;
+			};
+		};
+	};
+
+	gpio: gpio@23 {
+		compatible = "nxp,pca9555";
+		reg = <0x23>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-parent = <&gsc>;
+		interrupts = <4>;
+	};
+
+	eeprom@50 {
+		compatible = "atmel,24c02";
+		reg = <0x50>;
+		pagesize = <16>;
+	};
+
+	eeprom@51 {
+		compatible = "atmel,24c02";
+		reg = <0x51>;
+		pagesize = <16>;
+	};
+
+	eeprom@52 {
+		compatible = "atmel,24c02";
+		reg = <0x52>;
+		pagesize = <16>;
+	};
+
+	eeprom@53 {
+		compatible = "atmel,24c02";
+		reg = <0x53>;
+		pagesize = <16>;
+	};
+
+	rtc@68 {
+		compatible = "dallas,ds1672";
+		reg = <0x68>;
+	};
+};
+
+&i2c2 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	status = "okay";
+
+	pmic@4b {
+		compatible = "rohm,bd71847";
+		reg = <0x4b>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_pmic>;
+		interrupt-parent = <&gpio3>;
+		interrupts = <8 IRQ_TYPE_LEVEL_LOW>;
+		rohm,reset-snvs-powered;
+		#clock-cells = <0>;
+		clocks = <&osc_32k 0>;
+		clock-output-names = "clk-32k-out";
+
+		regulators {
+			/* vdd_soc: 0.805-0.900V (typ=0.8V) */
+			BUCK1 {
+				regulator-name = "buck1";
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <1300000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <1250>;
+			};
+
+			/* vdd_arm: 0.805-1.0V (typ=0.9V) */
+			buck2: BUCK2 {
+				regulator-name = "buck2";
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <1300000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <1250>;
+				rohm,dvs-run-voltage = <1000000>;
+				rohm,dvs-idle-voltage = <900000>;
+			};
+
+			/* vdd_0p9: 0.805-1.0V (typ=0.9V) */
+			BUCK3 {
+				regulator-name = "buck3";
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			/* vdd_3p3 */
+			BUCK4 {
+				regulator-name = "buck4";
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			/* vdd_1p8 */
+			BUCK5 {
+				regulator-name = "buck5";
+				regulator-min-microvolt = <1605000>;
+				regulator-max-microvolt = <1995000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			/* vdd_dram */
+			BUCK6 {
+				regulator-name = "buck6";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1400000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			/* nvcc_snvs_1p8 */
+			LDO1 {
+				regulator-name = "ldo1";
+				regulator-min-microvolt = <1600000>;
+				regulator-max-microvolt = <1900000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			/* vdd_snvs_0p8 */
+			LDO2 {
+				regulator-name = "ldo2";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <900000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			/* vdda_1p8 */
+			LDO3 {
+				regulator-name = "ldo3";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			LDO4 {
+				regulator-name = "ldo4";
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			LDO6 {
+				regulator-name = "ldo6";
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+		};
+	};
+};
+
+&i2c3 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "okay";
+
+	accelerometer@19 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_accel>;
+		compatible = "st,lis2de12";
+		reg = <0x19>;
+		st,drdy-int-pin = <1>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <15 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-names = "INT1";
+	};
+};
+
+&pcie_phy {
+	fsl,refclk-pad-mode = <IMX8_PCIE_REFCLK_PAD_INPUT>;
+	fsl,clkreq-unsupported;
+	clocks = <&pcie0_refclk>;
+	clock-names = "ref";
+	status = "okay";
+};
+
+&pcie0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pcie0>;
+	reset-gpio = <&gpio5 11 GPIO_ACTIVE_LOW>;
+	clocks = <&clk IMX8MM_CLK_PCIE1_ROOT>, <&clk IMX8MM_CLK_PCIE1_AUX>,
+		 <&pcie0_refclk>;
+	clock-names = "pcie", "pcie_aux", "pcie_bus";
+	assigned-clocks = <&clk IMX8MM_CLK_PCIE1_AUX>,
+			  <&clk IMX8MM_CLK_PCIE1_CTRL>;
+	assigned-clock-rates = <10000000>, <250000000>;
+	assigned-clock-parents = <&clk IMX8MM_SYS_PLL2_50M>,
+				 <&clk IMX8MM_SYS_PLL2_250M>;
+	status = "okay";
+};
+
+&pgc_mipi {
+	status = "disabled";
+};
+
+/* off-board RS232/RS485/RS422 */
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	cts-gpios = <&gpio1 3 GPIO_ACTIVE_LOW>;
+	rts-gpios = <&gpio1 5 GPIO_ACTIVE_LOW>;
+	dtr-gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
+	dsr-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
+	dcd-gpios = <&gpio3 24 GPIO_ACTIVE_LOW>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+/* console */
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	status = "okay";
+};
+
+&usbotg1 {
+	dr_mode = "host";
+	disable-over-current;
+	status = "okay";
+};
+
+/* microSD */
+&usdhc2 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
+	cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
+	bus-width = <4>;
+	vmmc-supply = <&reg_3p3v>;
+	status = "okay";
+};
+
+/* eMMC */
+&usdhc3 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+	bus-width = <8>;
+	non-removable;
+	status = "okay";
+};
+
+&wdog1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog>;
+	fsl,ext-reset-output;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hog>;
+
+	pinctrl_hog: hoggrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO10_GPIO1_IO10	0x40000041 /* RS422# */
+			MX8MM_IOMUXC_GPIO1_IO11_GPIO1_IO11	0x40000041 /* RS485# */
+			MX8MM_IOMUXC_GPIO1_IO12_GPIO1_IO12	0x40000041 /* RS232# */
+			MX8MM_IOMUXC_SD1_DATA7_GPIO2_IO9	0x40000041 /* DIG1_IN */
+			MX8MM_IOMUXC_SD1_DATA6_GPIO2_IO8	0x40000041 /* DIG1_OUT */
+			MX8MM_IOMUXC_SD1_DATA4_GPIO2_IO6	0x40000041 /* DIG1_CTL */
+			MX8MM_IOMUXC_SD1_DATA0_GPIO2_IO2	0x40000041 /* DIG2_CTL */
+			MX8MM_IOMUXC_SD1_CLK_GPIO2_IO0		0x40000041 /* DIG2_IN */
+			MX8MM_IOMUXC_SD1_CMD_GPIO2_IO1		0x40000041 /* DIG2_OUT */
+			MX8MM_IOMUXC_ECSPI1_MOSI_GPIO5_IO7	0x40000041 /* SIM1DET# */
+			MX8MM_IOMUXC_ECSPI1_MISO_GPIO5_IO8	0x40000041 /* SIM2DET# */
+			MX8MM_IOMUXC_ECSPI1_SS0_GPIO5_IO9	0x40000041 /* SIM2SEL */
+			MX8MM_IOMUXC_ECSPI2_MISO_GPIO5_IO12	0x40000041 /* PCI_WDIS# */
+		>;
+	};
+
+	pinctrl_accel: accelgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO15_GPIO1_IO15	0x159
+		>;
+	};
+
+	pinctrl_fec1: fec1grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_ENET_MDC_ENET1_MDC			0x3
+			MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO		0x3
+			MX8MM_IOMUXC_ENET_TD3_ENET1_RGMII_TD3		0x1f
+			MX8MM_IOMUXC_ENET_TD2_ENET1_RGMII_TD2		0x1f
+			MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1		0x1f
+			MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0		0x1f
+			MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3		0x91
+			MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2		0x91
+			MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1		0x91
+			MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0		0x91
+			MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC		0x1f
+			MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC		0x91
+			MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL	0x91
+			MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL	0x1f
+			MX8MM_IOMUXC_SAI2_TXFS_GPIO4_IO24		0x19 /* IRQ# */
+			MX8MM_IOMUXC_SAI2_TXC_GPIO4_IO25		0x19 /* RST# */
+		>;
+	};
+
+	pinctrl_gsc: gscgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI2_TXD0_GPIO4_IO26	0x159
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL		0x400001c3
+			MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA		0x400001c3
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_I2C2_SCL_I2C2_SCL		0x400001c3
+			MX8MM_IOMUXC_I2C2_SDA_I2C2_SDA		0x400001c3
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_I2C3_SCL_I2C3_SCL		0x400001c3
+			MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA		0x400001c3
+		>;
+	};
+
+	pinctrl_gpio_leds: gpioledgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SPDIF_EXT_CLK_GPIO5_IO5	0x19
+			MX8MM_IOMUXC_SAI3_RXD_GPIO4_IO30	0x19
+			MX8MM_IOMUXC_SAI3_MCLK_GPIO5_IO2	0x19
+			MX8MM_IOMUXC_GPIO1_IO14_GPIO1_IO14	0x19
+			MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9	0x19
+			MX8MM_IOMUXC_SPDIF_TX_GPIO5_IO3		0x19
+			MX8MM_IOMUXC_SAI3_RXC_GPIO4_IO29	0x19
+			MX8MM_IOMUXC_SAI3_RXFS_GPIO4_IO28	0x19
+			MX8MM_IOMUXC_GPIO1_IO13_GPIO1_IO13	0x19
+			MX8MM_IOMUXC_SAI3_TXFS_GPIO4_IO31	0x19
+			MX8MM_IOMUXC_SPDIF_RX_GPIO5_IO4		0x19
+			MX8MM_IOMUXC_GPIO1_IO08_GPIO1_IO8	0x19
+		>;
+	};
+
+	pinctrl_pcie0: pciegrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_ECSPI2_MOSI_GPIO5_IO11	0x41
+		>;
+	};
+
+	pinctrl_pmic: pmicgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_NAND_DATA02_GPIO3_IO8	0x41
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_UART1_RXD_UART1_DCE_RX	0x140
+			MX8MM_IOMUXC_UART1_TXD_UART1_DCE_TX	0x140
+			MX8MM_IOMUXC_GPIO1_IO00_GPIO1_IO0	0x140
+			MX8MM_IOMUXC_GPIO1_IO01_GPIO1_IO1	0x140
+			MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3	0x140
+			MX8MM_IOMUXC_GPIO1_IO05_GPIO1_IO5	0x140
+			MX8MM_IOMUXC_SAI5_RXD3_GPIO3_IO24	0x140
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_UART2_RXD_UART2_DCE_RX	0x140
+			MX8MM_IOMUXC_UART2_TXD_UART2_DCE_TX	0x140
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK		0x190
+			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD		0x1d0
+			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0	0x1d0
+			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1	0x1d0
+			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2	0x1d0
+			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3	0x1d0
+		>;
+	};
+
+	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK		0x194
+			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD		0x1d4
+			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0	0x1d4
+			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1	0x1d4
+			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2	0x1d4
+			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3	0x1d4
+		>;
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK		0x196
+			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD		0x1d6
+			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0	0x1d6
+			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1	0x1d6
+			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2	0x1d6
+			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3	0x1d6
+		>;
+	};
+
+	pinctrl_usdhc2_gpio: usdhc2-gpiogrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12	0x1c4
+			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT  0x1d0
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK	0x190
+			MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD	0x1d0
+			MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0	0x1d0
+			MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1	0x1d0
+			MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2	0x1d0
+			MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3	0x1d0
+			MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4	0x1d0
+			MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5	0x1d0
+			MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6	0x1d0
+			MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7	0x1d0
+			MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE	0x190
+		>;
+	};
+
+	pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK	0x194
+			MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD	0x1d4
+			MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0	0x1d4
+			MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1	0x1d4
+			MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2	0x1d4
+			MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3	0x1d4
+			MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4	0x1d4
+			MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5	0x1d4
+			MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6	0x1d4
+			MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7	0x1d4
+			MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE	0x194
+		>;
+	};
+
+	pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK	0x196
+			MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD	0x1d6
+			MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0	0x1d6
+			MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1	0x1d6
+			MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2	0x1d6
+			MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3	0x1d6
+			MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4	0x1d6
+			MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5	0x1d6
+			MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6	0x1d6
+			MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7	0x1d6
+			MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE	0x196
+		>;
+	};
+
+	pinctrl_wdog: wdoggrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B	0xc6
+		>;
+	};
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-venice-gw7904.dts b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw7904.dts
new file mode 100644
index 000000000000..a67771d02146
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-venice-gw7904.dts
@@ -0,0 +1,888 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2022 Gateworks Corporation
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/phy/phy-imx8-pcie.h>
+
+#include "imx8mm.dtsi"
+
+/ {
+	model = "Gateworks Venice GW7904 i.MX8MM board";
+	compatible = "gateworks,imx8mm-gw7904", "fsl,imx8mm";
+
+	chosen {
+		stdout-path = &uart2;
+	};
+
+	memory@40000000 {
+		device_type = "memory";
+		reg = <0x0 0x40000000 0 0x80000000>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		key-0 {
+			label = "user_pb";
+			gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
+			linux,code = <BTN_0>;
+		};
+
+		key-1 {
+			label = "user_pb1x";
+			linux,code = <BTN_1>;
+			interrupt-parent = <&gsc>;
+			interrupts = <0>;
+		};
+
+		key-2 {
+			label = "key_erased";
+			linux,code = <BTN_2>;
+			interrupt-parent = <&gsc>;
+			interrupts = <1>;
+		};
+
+		key-3 {
+			label = "eeprom_wp";
+			linux,code = <BTN_3>;
+			interrupt-parent = <&gsc>;
+			interrupts = <2>;
+		};
+
+		key-4 {
+			label = "switch_hold";
+			linux,code = <BTN_5>;
+			interrupt-parent = <&gsc>;
+			interrupts = <7>;
+		};
+	};
+
+	led-controller {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_leds>;
+
+		led-0 {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_GREEN>;
+			label = "led01_grn";
+			gpios = <&gpioled 0 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led-1 {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_YELLOW>;
+			label = "led01_yel";
+			gpios = <&gpioled 1 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led-2 {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_GREEN>;
+			label = "led02_grn";
+			gpios = <&gpioled 2 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led-3 {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_YELLOW>;
+			label = "led02_yel";
+			gpios = <&gpioled 3 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led-4 {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_GREEN>;
+			label = "led03_grn";
+			gpios = <&gpioled 4 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led-5 {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_YELLOW>;
+			label = "led03_yel";
+			gpios = <&gpioled 5 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led-6 {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_GREEN>;
+			label = "led04_grn";
+			gpios = <&gpioled 6 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led-7 {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_YELLOW>;
+			label = "led04_yel";
+			gpios = <&gpioled 7 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led-8 {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_GREEN>;
+			label = "led05_grn";
+			gpios = <&gpioled 8 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led-9 {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_YELLOW>;
+			label = "led05_yel";
+			gpios = <&gpioled 9 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led-10 {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_GREEN>;
+			label = "led06_grn";
+			gpios = <&gpio1 8 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led-11 {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_RED>;
+			label = "led06_red";
+			gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led-12 {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_GREEN>;
+			label = "led07_grn";
+			gpios = <&gpio1 10 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led-13 {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_RED>;
+			label = "led07_red";
+			gpios = <&gpio1 11 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led-14 {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_GREEN>;
+			label = "led08_grn";
+			gpios = <&gpioled 10 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led-15 {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_YELLOW>;
+			label = "led08_yel";
+			gpios = <&gpioled 11 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led-16 {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_GREEN>;
+			label = "led09_grn";
+			gpios = <&gpioled 12 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led-17 {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_YELLOW>;
+			label = "led09_yel";
+			gpios = <&gpioled 13 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led-18 {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_GREEN>;
+			label = "led10_grn";
+			gpios = <&gpioled 14 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+
+		led-19 {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_YELLOW>;
+			label = "led10_yel";
+			gpios = <&gpioled 15 GPIO_ACTIVE_LOW>;
+			default-state = "off";
+		};
+	};
+
+	pcie0_refclk: pcie0-refclk {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <100000000>;
+	};
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+};
+
+&A53_0 {
+	cpu-supply = <&buck2>;
+};
+
+&A53_1 {
+	cpu-supply = <&buck2>;
+};
+
+&A53_2 {
+	cpu-supply = <&buck2>;
+};
+
+&A53_3 {
+	cpu-supply = <&buck2>;
+};
+
+&ddrc {
+	operating-points-v2 = <&ddrc_opp_table>;
+
+	ddrc_opp_table: opp-table {
+		compatible = "operating-points-v2";
+
+		opp-25M {
+			opp-hz = /bits/ 64 <25000000>;
+		};
+
+		opp-100M {
+			opp-hz = /bits/ 64 <100000000>;
+		};
+
+		opp-750M {
+			opp-hz = /bits/ 64 <750000000>;
+		};
+	};
+};
+
+&fec1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_fec1>;
+	phy-mode = "rgmii-id";
+	phy-handle = <&ethphy0>;
+	local-mac-address = [00 00 00 00 00 00];
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy0: ethernet-phy@0 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <0>;
+		};
+	};
+};
+
+&gpio1 {
+	gpio-line-names = "", "", "", "", "", "", "", "",
+		"", "", "", "", "rs232_en#", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "";
+};
+
+&gpio5 {
+	gpio-line-names = "", "", "", "", "", "", "", "",
+		"", "", "", "", "pci_wdis#", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "";
+};
+
+&i2c1 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+
+	gsc: gsc@20 {
+		compatible = "gw,gsc";
+		reg = <0x20>;
+		pinctrl-0 = <&pinctrl_gsc>;
+		interrupt-parent = <&gpio4>;
+		interrupts = <26 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-controller;
+		#interrupt-cells = <1>;
+
+		adc {
+			compatible = "gw,gsc-adc";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			channel@6 {
+				gw,mode = <0>;
+				reg = <0x06>;
+				label = "temp";
+			};
+
+			channel@82 {
+				gw,mode = <2>;
+				reg = <0x82>;
+				label = "vin";
+				gw,voltage-divider-ohms = <22100 1000>;
+				gw,voltage-offset-microvolt = <700000>;
+			};
+
+			channel@84 {
+				gw,mode = <2>;
+				reg = <0x84>;
+				label = "vdd_5p0";
+				gw,voltage-divider-ohms = <10000 10000>;
+			};
+
+			channel@86 {
+				gw,mode = <2>;
+				reg = <0x86>;
+				label = "vdd_3p3";
+				gw,voltage-divider-ohms = <10000 10000>;
+			};
+
+			channel@88 {
+				gw,mode = <2>;
+				reg = <0x88>;
+				label = "vdd_0p9";
+			};
+
+			channel@8c {
+				gw,mode = <2>;
+				reg = <0x8c>;
+				label = "vdd_soc";
+			};
+
+			channel@8e {
+				gw,mode = <2>;
+				reg = <0x8e>;
+				label = "vdd_arm";
+			};
+
+			channel@90 {
+				gw,mode = <2>;
+				reg = <0x90>;
+				label = "vdd_1p8";
+			};
+
+			channel@92 {
+				gw,mode = <2>;
+				reg = <0x92>;
+				label = "vdd_dram";
+			};
+
+			channel@a2 {
+				gw,mode = <2>;
+				reg = <0xa2>;
+				label = "vdd_gsc";
+				gw,voltage-divider-ohms = <10000 10000>;
+			};
+		};
+	};
+
+	gpio: gpio@23 {
+		compatible = "nxp,pca9555";
+		reg = <0x23>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-parent = <&gsc>;
+		interrupts = <4>;
+	};
+
+	eeprom@50 {
+		compatible = "atmel,24c02";
+		reg = <0x50>;
+		pagesize = <16>;
+	};
+
+	eeprom@51 {
+		compatible = "atmel,24c02";
+		reg = <0x51>;
+		pagesize = <16>;
+	};
+
+	eeprom@52 {
+		compatible = "atmel,24c02";
+		reg = <0x52>;
+		pagesize = <16>;
+	};
+
+	eeprom@53 {
+		compatible = "atmel,24c02";
+		reg = <0x53>;
+		pagesize = <16>;
+	};
+
+	rtc@68 {
+		compatible = "dallas,ds1672";
+		reg = <0x68>;
+	};
+};
+
+&i2c2 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	status = "okay";
+
+	pmic@4b {
+		compatible = "rohm,bd71847";
+		reg = <0x4b>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_pmic>;
+		interrupt-parent = <&gpio3>;
+		interrupts = <8 IRQ_TYPE_LEVEL_LOW>;
+		rohm,reset-snvs-powered;
+		#clock-cells = <0>;
+		clocks = <&osc_32k 0>;
+		clock-output-names = "clk-32k-out";
+
+		regulators {
+			/* vdd_soc: 0.805-0.900V (typ=0.8V) */
+			BUCK1 {
+				regulator-name = "buck1";
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <1300000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <1250>;
+			};
+
+			/* vdd_arm: 0.805-1.0V (typ=0.9V) */
+			buck2: BUCK2 {
+				regulator-name = "buck2";
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <1300000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <1250>;
+				rohm,dvs-run-voltage = <1000000>;
+				rohm,dvs-idle-voltage = <900000>;
+			};
+
+			/* vdd_0p9: 0.805-1.0V (typ=0.9V) */
+			BUCK3 {
+				regulator-name = "buck3";
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			/* vdd_3p3 */
+			BUCK4 {
+				regulator-name = "buck4";
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			/* vdd_1p8 */
+			BUCK5 {
+				regulator-name = "buck5";
+				regulator-min-microvolt = <1605000>;
+				regulator-max-microvolt = <1995000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			/* vdd_dram */
+			BUCK6 {
+				regulator-name = "buck6";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1400000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			/* nvcc_snvs_1p8 */
+			LDO1 {
+				regulator-name = "ldo1";
+				regulator-min-microvolt = <1600000>;
+				regulator-max-microvolt = <1900000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			/* vdd_snvs_0p8 */
+			LDO2 {
+				regulator-name = "ldo2";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <900000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			/* vdda_1p8 */
+			LDO3 {
+				regulator-name = "ldo3";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			LDO4 {
+				regulator-name = "ldo4";
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			LDO6 {
+				regulator-name = "ldo6";
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+		};
+	};
+};
+
+&i2c3 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "okay";
+
+	accelerometer@19 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_accel>;
+		compatible = "st,lis2de12";
+		reg = <0x19>;
+		st,drdy-int-pin = <1>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <15 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-names = "INT1";
+	};
+};
+
+&i2c4 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c4>;
+	status = "okay";
+
+	gpioled: gpio@27 {
+		compatible = "nxp,pca9555";
+		reg = <0x27>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+};
+
+&pcie_phy {
+	fsl,refclk-pad-mode = <IMX8_PCIE_REFCLK_PAD_INPUT>;
+	fsl,clkreq-unsupported;
+	clocks = <&pcie0_refclk>;
+	clock-names = "ref";
+	status = "okay";
+};
+
+&pcie0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pcie0>;
+	reset-gpio = <&gpio5 11 GPIO_ACTIVE_LOW>;
+	clocks = <&clk IMX8MM_CLK_PCIE1_ROOT>, <&clk IMX8MM_CLK_PCIE1_AUX>,
+		 <&pcie0_refclk>;
+	clock-names = "pcie", "pcie_aux", "pcie_bus";
+	assigned-clocks = <&clk IMX8MM_CLK_PCIE1_AUX>,
+			  <&clk IMX8MM_CLK_PCIE1_CTRL>;
+	assigned-clock-rates = <10000000>, <250000000>;
+	assigned-clock-parents = <&clk IMX8MM_SYS_PLL2_50M>,
+				 <&clk IMX8MM_SYS_PLL2_250M>;
+	status = "okay";
+};
+
+&pgc_mipi {
+	status = "disabled";
+};
+
+/* off-board RS232 */
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+/* console */
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	status = "okay";
+};
+
+/* off-board RS232 */
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	status = "okay";
+};
+
+&usbotg1 {
+	dr_mode = "host";
+	disable-over-current;
+	status = "okay";
+};
+
+/* microSD */
+&usdhc2 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
+	cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
+	bus-width = <4>;
+	vmmc-supply = <&reg_3p3v>;
+	status = "okay";
+};
+
+/* eMMC */
+&usdhc3 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+	bus-width = <8>;
+	non-removable;
+	status = "okay";
+};
+
+&wdog1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog>;
+	fsl,ext-reset-output;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hog>;
+
+	pinctrl_hog: hoggrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO12_GPIO1_IO12	0x40000041 /* RS232# */
+			MX8MM_IOMUXC_ECSPI2_MISO_GPIO5_IO12	0x40000041 /* PCI_WDIS# */
+		>;
+	};
+
+	pinctrl_accel: accelgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO15_GPIO1_IO15	0x159
+		>;
+	};
+
+	pinctrl_fec1: fec1grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_ENET_MDC_ENET1_MDC			0x3
+			MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO		0x3
+			MX8MM_IOMUXC_ENET_TD3_ENET1_RGMII_TD3		0x1f
+			MX8MM_IOMUXC_ENET_TD2_ENET1_RGMII_TD2		0x1f
+			MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1		0x1f
+			MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0		0x1f
+			MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3		0x91
+			MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2		0x91
+			MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1		0x91
+			MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0		0x91
+			MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC		0x1f
+			MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC		0x91
+			MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL	0x91
+			MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL	0x1f
+			MX8MM_IOMUXC_SAI2_TXFS_GPIO4_IO24		0x19 /* IRQ# */
+			MX8MM_IOMUXC_SAI2_TXC_GPIO4_IO25		0x19 /* RST# */
+		>;
+	};
+
+	pinctrl_gpio_leds: gpioledsgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO08_GPIO1_IO8	0x40000019
+			MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9	0x40000019
+			MX8MM_IOMUXC_GPIO1_IO10_GPIO1_IO10	0x40000019
+			MX8MM_IOMUXC_GPIO1_IO11_GPIO1_IO11	0x40000019
+		>;
+	};
+
+	pinctrl_gsc: gscgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SAI2_TXD0_GPIO4_IO26	0x159
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL		0x400001c3
+			MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA		0x400001c3
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_I2C2_SCL_I2C2_SCL		0x400001c3
+			MX8MM_IOMUXC_I2C2_SDA_I2C2_SDA		0x400001c3
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_I2C3_SCL_I2C3_SCL		0x400001c3
+			MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA		0x400001c3
+		>;
+	};
+
+	pinctrl_i2c4: i2c4grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_I2C4_SCL_I2C4_SCL		0x400001c3
+			MX8MM_IOMUXC_I2C4_SDA_I2C4_SDA		0x400001c3
+		>;
+	};
+
+	pinctrl_pcie0: pciegrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_ECSPI2_MOSI_GPIO5_IO11	0x41
+		>;
+	};
+
+	pinctrl_pmic: pmicgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_NAND_DATA02_GPIO3_IO8	0x41
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_UART1_RXD_UART1_DCE_RX	0x140
+			MX8MM_IOMUXC_UART1_TXD_UART1_DCE_TX	0x140
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_UART2_RXD_UART2_DCE_RX	0x140
+			MX8MM_IOMUXC_UART2_TXD_UART2_DCE_TX	0x140
+		>;
+	};
+
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_UART3_RXD_UART3_DCE_RX	0x140
+			MX8MM_IOMUXC_UART3_TXD_UART3_DCE_TX	0x140
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK		0x190
+			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD		0x1d0
+			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0	0x1d0
+			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1	0x1d0
+			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2	0x1d0
+			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3	0x1d0
+		>;
+	};
+
+	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK		0x194
+			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD		0x1d4
+			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0	0x1d4
+			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1	0x1d4
+			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2	0x1d4
+			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3	0x1d4
+		>;
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK		0x196
+			MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD		0x1d6
+			MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0	0x1d6
+			MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1	0x1d6
+			MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2	0x1d6
+			MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3	0x1d6
+		>;
+	};
+
+	pinctrl_usdhc2_gpio: usdhc2-gpiogrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12	0x1c4
+			MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT  0x1d0
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK	0x190
+			MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD	0x1d0
+			MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0	0x1d0
+			MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1	0x1d0
+			MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2	0x1d0
+			MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3	0x1d0
+			MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4	0x1d0
+			MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5	0x1d0
+			MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6	0x1d0
+			MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7	0x1d0
+			MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE	0x190
+		>;
+	};
+
+	pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK	0x194
+			MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD	0x1d4
+			MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0	0x1d4
+			MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1	0x1d4
+			MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2	0x1d4
+			MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3	0x1d4
+			MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4	0x1d4
+			MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5	0x1d4
+			MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6	0x1d4
+			MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7	0x1d4
+			MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE	0x194
+		>;
+	};
+
+	pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK	0x196
+			MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD	0x1d6
+			MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0	0x1d6
+			MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1	0x1d6
+			MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2	0x1d6
+			MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3	0x1d6
+			MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4	0x1d6
+			MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5	0x1d6
+			MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6	0x1d6
+			MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7	0x1d6
+			MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE	0x196
+		>;
+	};
+
+	pinctrl_wdog: wdoggrp {
+		fsl,pins = <
+			MX8MM_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B	0xc6
+		>;
+	};
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-verdin-dahlia.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-verdin-dahlia.dtsi
new file mode 100644
index 000000000000..c2a5c2f7b204
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-verdin-dahlia.dtsi
@@ -0,0 +1,150 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/ {
+	sound_card: sound-card {
+		compatible = "simple-audio-card";
+		simple-audio-card,bitclock-master = <&dailink_master>;
+		simple-audio-card,format = "i2s";
+		simple-audio-card,frame-master = <&dailink_master>;
+		simple-audio-card,name = "imx8mm-wm8904";
+		simple-audio-card,routing =
+			"Headphone Jack", "HPOUTL",
+			"Headphone Jack", "HPOUTR",
+			"IN2L", "Line In Jack",
+			"IN2R", "Line In Jack",
+			"Headphone Jack", "MICBIAS",
+			"IN1L", "Headphone Jack";
+		simple-audio-card,widgets =
+			"Microphone", "Headphone Jack",
+			"Headphone", "Headphone Jack",
+			"Line", "Line In Jack";
+
+		dailink_master: simple-audio-card,codec {
+			clocks = <&clk IMX8MM_CLK_SAI2_ROOT>;
+			sound-dai = <&wm8904_1a>;
+		};
+
+		simple-audio-card,cpu {
+			sound-dai = <&sai2>;
+		};
+	};
+};
+
+/* Verdin SPI_1 */
+&ecspi2 {
+	status = "okay";
+};
+
+/* EEPROM on display adapter boards */
+&eeprom_display_adapter {
+	status = "okay";
+};
+
+/* EEPROM on Verdin Development board */
+&eeprom_carrier_board {
+	status = "okay";
+};
+
+&fec1 {
+	status = "okay";
+};
+
+/* Verdin QSPI_1 */
+&flexspi {
+	status = "okay";
+};
+
+/* Current measurement into module VCC */
+&hwmon {
+	status = "okay";
+};
+
+&hwmon_temp {
+	vs-supply = <&reg_1p8v>;
+	status = "okay";
+};
+
+&i2c3 {
+	status = "okay";
+};
+
+/* Verdin I2C_1 */
+&i2c4 {
+	status = "okay";
+
+	/* Audio Codec */
+	wm8904_1a: audio-codec@1a {
+		compatible = "wlf,wm8904";
+		AVDD-supply = <&reg_3p3v>;
+		clocks = <&clk IMX8MM_CLK_SAI2_ROOT>;
+		clock-names = "mclk";
+		CPVDD-supply = <&reg_3p3v>;
+		DBVDD-supply = <&reg_3p3v>;
+		DCVDD-supply = <&reg_3p3v>;
+		MICVDD-supply = <&reg_3p3v>;
+		reg = <0x1a>;
+		#sound-dai-cells = <0>;
+	};
+};
+
+/* Verdin PCIE_1 */
+&pcie0 {
+	status = "okay";
+};
+
+&pcie_phy {
+	status = "okay";
+};
+
+/* Verdin PWM_3_DSI */
+&pwm1 {
+	status = "okay";
+};
+
+/* Verdin PWM_1 */
+&pwm2 {
+	status = "okay";
+};
+
+/* Verdin PWM_2 */
+&pwm3 {
+	status = "okay";
+};
+
+/* Verdin I2S_1 */
+&sai2 {
+	status = "okay";
+};
+
+/* Verdin UART_3 */
+&uart1 {
+	status = "okay";
+};
+
+/* Verdin UART_1 */
+&uart2 {
+	status = "okay";
+};
+
+/* Verdin UART_2 */
+&uart3 {
+	status = "okay";
+};
+
+/* Verdin USB_1 */
+&usbotg1 {
+	status = "okay";
+};
+
+/* Verdin USB_2 */
+&usbotg2 {
+	status = "okay";
+};
+
+/* Verdin SD_1 */
+&usdhc2 {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-verdin-dev.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-verdin-dev.dtsi
new file mode 100644
index 000000000000..73cc3fafa018
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-verdin-dev.dtsi
@@ -0,0 +1,67 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+#include "imx8mm-verdin-dahlia.dtsi"
+
+/ {
+	sound_card: sound-card {
+		compatible = "simple-audio-card";
+		simple-audio-card,bitclock-master = <&dailink_master>;
+		simple-audio-card,format = "i2s";
+		simple-audio-card,frame-master = <&dailink_master>;
+		simple-audio-card,name = "imx8mm-nau8822";
+		simple-audio-card,routing =
+			"Headphones", "LHP",
+			"Headphones", "RHP",
+			"Speaker", "LSPK",
+			"Speaker", "RSPK",
+			"Line Out", "AUXOUT1",
+			"Line Out", "AUXOUT2",
+			"LAUX", "Line In",
+			"RAUX", "Line In",
+			"LMICP", "Mic In",
+			"RMICP", "Mic In";
+		simple-audio-card,widgets =
+			"Headphones", "Headphones",
+			"Line Out", "Line Out",
+			"Speaker", "Speaker",
+			"Microphone", "Mic In",
+			"Line", "Line In";
+
+		dailink_master: simple-audio-card,codec {
+			clocks = <&clk IMX8MM_CLK_SAI2_ROOT>;
+			sound-dai = <&nau8822_1a>;
+		};
+
+		simple-audio-card,cpu {
+			sound-dai = <&sai2>;
+		};
+	};
+};
+
+&gpio_expander_21 {
+	status = "okay";
+};
+
+/* Verdin I2C_1 */
+&i2c4 {
+	/* Audio Codec */
+	nau8822_1a: audio-codec@1a {
+		compatible = "nuvoton,nau8822";
+		reg = <0x1a>;
+	};
+};
+
+/* Verdin UART_1, connector X50 through RS485 transceiver */
+&uart2 {
+	linux,rs485-enabled-at-boot-time;
+	rs485-rts-active-low;
+	rs485-rx-during-tx;
+};
+
+/* Limit frequency on dev board due to long traces and bad signal integrity */
+&usdhc2 {
+	max-frequency = <100000000>;
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-verdin-nonwifi-dahlia.dts b/arch/arm64/boot/dts/freescale/imx8mm-verdin-nonwifi-dahlia.dts
new file mode 100644
index 000000000000..d64ff378a152
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-verdin-nonwifi-dahlia.dts
@@ -0,0 +1,18 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/dts-v1/;
+
+#include "imx8mm-verdin.dtsi"
+#include "imx8mm-verdin-nonwifi.dtsi"
+#include "imx8mm-verdin-dahlia.dtsi"
+
+/ {
+	model = "Toradex Verdin iMX8M Mini on Dahlia Board";
+	compatible = "toradex,verdin-imx8mm-nonwifi-dahlia",
+		     "toradex,verdin-imx8mm-nonwifi",
+		     "toradex,verdin-imx8mm",
+		     "fsl,imx8mm";
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-verdin-nonwifi-dev.dts b/arch/arm64/boot/dts/freescale/imx8mm-verdin-nonwifi-dev.dts
new file mode 100644
index 000000000000..6ae71ecac8de
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-verdin-nonwifi-dev.dts
@@ -0,0 +1,18 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/dts-v1/;
+
+#include "imx8mm-verdin.dtsi"
+#include "imx8mm-verdin-nonwifi.dtsi"
+#include "imx8mm-verdin-dev.dtsi"
+
+/ {
+	model = "Toradex Verdin iMX8M Mini on Verdin Development Board";
+	compatible = "toradex,verdin-imx8mm-nonwifi-dev",
+		     "toradex,verdin-imx8mm-nonwifi",
+		     "toradex,verdin-imx8mm",
+		     "fsl,imx8mm";
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-verdin-nonwifi.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-verdin-nonwifi.dtsi
new file mode 100644
index 000000000000..1e0f87c7a609
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-verdin-nonwifi.dtsi
@@ -0,0 +1,75 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+&gpio3 {
+	gpio-line-names = "SODIMM_52",
+			  "SODIMM_54",
+			  "SODIMM_64",
+			  "SODIMM_21",
+			  "SODIMM_206",
+			  "SODIMM_76",
+			  "SODIMM_56",
+			  "SODIMM_58",
+			  "SODIMM_60",
+			  "SODIMM_62",
+			  "SODIMM_162",
+			  "SODIMM_164",
+			  "SODIMM_166",
+			  "SODIMM_168",
+			  "SODIMM_66",
+			  "SODIMM_17",
+			  "",
+			  "SODIMM_156",
+			  "SODIMM_160",
+			  "SODIMM_244",
+			  "",
+			  "SODIMM_48",
+			  "SODIMM_44",
+			  "SODIMM_42",
+			  "SODIMM_46";
+};
+
+&gpio4 {
+	gpio-line-names = "SODIMM_102",
+			  "SODIMM_90",
+			  "SODIMM_92",
+			  "SODIMM_94",
+			  "SODIMM_96",
+			  "SODIMM_100",
+			  "SODIMM_148",
+			  "SODIMM_152",
+			  "SODIMM_154",
+			  "SODIMM_174",
+			  "SODIMM_120",
+			  "SODIMM_104",
+			  "SODIMM_106",
+			  "SODIMM_108",
+			  "SODIMM_112",
+			  "SODIMM_114",
+			  "SODIMM_116",
+			  "SODIMM_150",
+			  "SODIMM_118",
+			  "",
+			  "SODIMM_88",
+			  "SODIMM_149",
+			  "SODIMM_147",
+			  "SODIMM_36",
+			  "SODIMM_32",
+			  "SODIMM_30",
+			  "SODIMM_34",
+			  "SODIMM_38",
+			  "SODIMM_252",
+			  "SODIMM_133",
+			  "SODIMM_135",
+			  "SODIMM_129";
+};
+
+&usdhc3 {
+	bus-width = <4>;
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-verdin-wifi-dahlia.dts b/arch/arm64/boot/dts/freescale/imx8mm-verdin-wifi-dahlia.dts
new file mode 100644
index 000000000000..d424c475cba1
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-verdin-wifi-dahlia.dts
@@ -0,0 +1,18 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/dts-v1/;
+
+#include "imx8mm-verdin.dtsi"
+#include "imx8mm-verdin-wifi.dtsi"
+#include "imx8mm-verdin-dahlia.dtsi"
+
+/ {
+	model = "Toradex Verdin iMX8M Mini WB on Dahlia Board";
+	compatible = "toradex,verdin-imx8mm-wifi-dahlia",
+		     "toradex,verdin-imx8mm-wifi",
+		     "toradex,verdin-imx8mm",
+		     "fsl,imx8mm";
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-verdin-wifi-dev.dts b/arch/arm64/boot/dts/freescale/imx8mm-verdin-wifi-dev.dts
new file mode 100644
index 000000000000..ef952021832e
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-verdin-wifi-dev.dts
@@ -0,0 +1,18 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/dts-v1/;
+
+#include "imx8mm-verdin.dtsi"
+#include "imx8mm-verdin-wifi.dtsi"
+#include "imx8mm-verdin-dev.dtsi"
+
+/ {
+	model = "Toradex Verdin iMX8M Mini WB on Verdin Development Board";
+	compatible = "toradex,verdin-imx8mm-wifi-dev",
+		     "toradex,verdin-imx8mm-wifi",
+		     "toradex,verdin-imx8mm",
+		     "fsl,imx8mm";
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-verdin-wifi.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-verdin-wifi.dtsi
new file mode 100644
index 000000000000..017db9eab256
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-verdin-wifi.dtsi
@@ -0,0 +1,94 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/ {
+	reg_wifi_en: regulator-wifi-en {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio3 25 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_wifi_pwr_en>;
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "PDn_AW-CM276NF";
+		startup-delay-us = <2000>;
+	};
+};
+
+&gpio3 {
+	gpio-line-names = "SODIMM_52",
+			  "SODIMM_54",
+			  "SODIMM_64",
+			  "SODIMM_21",
+			  "SODIMM_206",
+			  "SODIMM_76",
+			  "SODIMM_56",
+			  "SODIMM_58",
+			  "SODIMM_60",
+			  "SODIMM_62",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "SODIMM_66",
+			  "SODIMM_17",
+			  "",
+			  "",
+			  "",
+			  "SODIMM_244",
+			  "",
+			  "SODIMM_48",
+			  "SODIMM_44",
+			  "SODIMM_42",
+			  "SODIMM_46";
+};
+
+&gpio4 {
+	gpio-line-names = "SODIMM_102",
+			  "SODIMM_90",
+			  "SODIMM_92",
+			  "SODIMM_94",
+			  "SODIMM_96",
+			  "SODIMM_100",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "SODIMM_120",
+			  "SODIMM_104",
+			  "SODIMM_106",
+			  "SODIMM_108",
+			  "SODIMM_112",
+			  "SODIMM_114",
+			  "SODIMM_116",
+			  "",
+			  "SODIMM_118",
+			  "",
+			  "SODIMM_88",
+			  "SODIMM_149",
+			  "SODIMM_147",
+			  "SODIMM_36",
+			  "SODIMM_32",
+			  "SODIMM_30",
+			  "SODIMM_34",
+			  "SODIMM_38",
+			  "SODIMM_252",
+			  "SODIMM_133",
+			  "SODIMM_135",
+			  "SODIMM_129";
+};
+
+/* On-module Wi-Fi */
+&usdhc3 {
+	bus-width = <4>;
+	keep-power-in-suspend;
+	non-removable;
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc3>, <&pinctrl_wifi_ctrl>;
+	pinctrl-1 = <&pinctrl_usdhc3_100mhz>, <&pinctrl_wifi_ctrl>;
+	pinctrl-2 = <&pinctrl_usdhc3_200mhz>, <&pinctrl_wifi_ctrl>;
+	vmmc-supply = <&reg_wifi_en>;
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-verdin.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-verdin.dtsi
new file mode 100644
index 000000000000..bcab830c6e95
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mm-verdin.dtsi
@@ -0,0 +1,1319 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+#include "dt-bindings/phy/phy-imx8-pcie.h"
+#include "dt-bindings/pwm/pwm.h"
+#include "imx8mm.dtsi"
+
+/ {
+	chosen {
+		stdout-path = &uart1;
+	};
+
+	aliases {
+		rtc0 = &rtc_i2c;
+		rtc1 = &snvs_rtc;
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		brightness-levels = <0 45 63 88 119 158 203 255>;
+		default-brightness-level = <4>;
+		/* Verdin I2S_2_D_OUT (DSI_1_BKL_EN/DSI_1_BKL_EN_LVDS, SODIMM 46) */
+		enable-gpios = <&gpio3 24 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_i2s_2_d_out_dsi_1_bkl_en>;
+		power-supply = <&reg_3p3v>;
+		/* Verdin PWM_3_DSI/PWM_3_DSI_LVDS (SODIMM 19) */
+		pwms = <&pwm1 0 6666667 PWM_POLARITY_INVERTED>;
+		status = "disabled";
+	};
+
+	/* Fixed clock dedicated to SPI CAN controller */
+	clk40m: oscillator {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <40000000>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_keys>;
+
+		key-wakeup {
+			debounce-interval = <10>;
+			/* Verdin CTRL_WAKE1_MICO# (SODIMM 252) */
+			gpios = <&gpio4 28 GPIO_ACTIVE_LOW>;
+			label = "Wake-Up";
+			linux,code = <KEY_WAKEUP>;
+			wakeup-source;
+		};
+	};
+
+	hdmi_connector: hdmi-connector {
+		compatible = "hdmi-connector";
+		ddc-i2c-bus = <&i2c2>;
+		label = "hdmi";
+		type = "a";
+		status = "disabled";
+	};
+
+	panel_lvds: panel-lvds {
+		compatible = "panel-lvds";
+		backlight = <&backlight>;
+		data-mapping = "vesa-24";
+		status = "disabled";
+	};
+
+	/* Carrier Board Supplies */
+	reg_1p8v: regulator-1p8v {
+		compatible = "regulator-fixed";
+		regulator-max-microvolt = <1800000>;
+		regulator-min-microvolt = <1800000>;
+		regulator-name = "+V1.8_SW";
+	};
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "+V3.3_SW";
+	};
+
+	reg_5p0v: regulator-5p0v {
+		compatible = "regulator-fixed";
+		regulator-max-microvolt = <5000000>;
+		regulator-min-microvolt = <5000000>;
+		regulator-name = "+V5_SW";
+	};
+
+	/* Non PMIC On-module Supplies */
+	reg_ethphy: regulator-ethphy {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio2 20 GPIO_ACTIVE_HIGH>; /* PMIC_EN_ETH */
+		off-on-delay = <500000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_eth>;
+		regulator-boot-on;
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "On-module +V3.3_ETH";
+		startup-delay-us = <200000>;
+	};
+
+	reg_usb_otg1_vbus: regulator-usb-otg1 {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		/* Verdin USB_1_EN (SODIMM 155) */
+		gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_usb1_en>;
+		regulator-max-microvolt = <5000000>;
+		regulator-min-microvolt = <5000000>;
+		regulator-name = "USB_1_EN";
+	};
+
+	reg_usb_otg2_vbus: regulator-usb-otg2 {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		/* Verdin USB_2_EN (SODIMM 185) */
+		gpio = <&gpio1 14 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_usb2_en>;
+		regulator-max-microvolt = <5000000>;
+		regulator-min-microvolt = <5000000>;
+		regulator-name = "USB_2_EN";
+	};
+
+	reg_usdhc2_vmmc: regulator-usdhc2 {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		/* Verdin SD_1_PWR_EN (SODIMM 76) */
+		gpio = <&gpio3 5 GPIO_ACTIVE_HIGH>;
+		off-on-delay = <100000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usdhc2_pwr_en>;
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "+V3.3_SD";
+		startup-delay-us = <2000>;
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		/* Use the kernel configuration settings instead */
+		/delete-node/ linux,cma;
+	};
+};
+
+&A53_0 {
+	cpu-supply = <&reg_vdd_arm>;
+};
+
+&A53_1 {
+	cpu-supply = <&reg_vdd_arm>;
+};
+
+&A53_2 {
+	cpu-supply = <&reg_vdd_arm>;
+};
+
+&A53_3 {
+	cpu-supply = <&reg_vdd_arm>;
+};
+
+&cpu_alert0 {
+	temperature = <95000>;
+};
+
+&cpu_crit0 {
+	temperature = <105000>;
+};
+
+&ddrc {
+	operating-points-v2 = <&ddrc_opp_table>;
+
+	ddrc_opp_table: opp-table {
+		compatible = "operating-points-v2";
+
+		opp-25M {
+			opp-hz = /bits/ 64 <25000000>;
+		};
+
+		opp-100M {
+			opp-hz = /bits/ 64 <100000000>;
+		};
+
+		opp-750M {
+			opp-hz = /bits/ 64 <750000000>;
+		};
+	};
+};
+
+/* Verdin SPI_1 */
+&ecspi2 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	cs-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi2>;
+};
+
+/* Verdin CAN_1 (On-module) */
+&ecspi3 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	cs-gpios = <&gpio5 25 GPIO_ACTIVE_LOW>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi3>;
+	status = "okay";
+
+	can1: can@0 {
+		compatible = "microchip,mcp251xfd";
+		clocks = <&clk40m>;
+		interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_can1_int>;
+		reg = <0>;
+		spi-max-frequency = <8500000>;
+	};
+};
+
+/* Verdin ETH_1 (On-module PHY) */
+&fec1 {
+	fsl,magic-packet;
+	phy-handle = <&ethphy0>;
+	phy-mode = "rgmii-id";
+	phy-supply = <&reg_ethphy>;
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&pinctrl_fec1>;
+	pinctrl-1 = <&pinctrl_fec1_sleep>;
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy0: ethernet-phy@7 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			interrupt-parent = <&gpio1>;
+			interrupts = <10 IRQ_TYPE_LEVEL_LOW>;
+			micrel,led-mode = <0>;
+			reg = <7>;
+		};
+	};
+};
+
+/* Verdin QSPI_1 */
+&flexspi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexspi0>;
+};
+
+&gpio1 {
+	gpio-line-names = "SODIMM_216",
+			  "SODIMM_19",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "SODIMM_220",
+			  "SODIMM_222",
+			  "",
+			  "SODIMM_218",
+			  "SODIMM_155",
+			  "SODIMM_157",
+			  "SODIMM_185",
+			  "SODIMM_187";
+};
+
+&gpio2 {
+	gpio-line-names = "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "SODIMM_84",
+			  "SODIMM_78",
+			  "SODIMM_74",
+			  "SODIMM_80",
+			  "SODIMM_82",
+			  "SODIMM_70",
+			  "SODIMM_72";
+};
+
+&gpio5 {
+	gpio-line-names = "SODIMM_131",
+			  "",
+			  "SODIMM_91",
+			  "SODIMM_16",
+			  "SODIMM_15",
+			  "SODIMM_208",
+			  "SODIMM_137",
+			  "SODIMM_139",
+			  "SODIMM_141",
+			  "SODIMM_143",
+			  "SODIMM_196",
+			  "SODIMM_200",
+			  "SODIMM_198",
+			  "SODIMM_202",
+			  "",
+			  "",
+			  "SODIMM_55",
+			  "SODIMM_53",
+			  "SODIMM_95",
+			  "SODIMM_93",
+			  "SODIMM_14",
+			  "SODIMM_12",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "SODIMM_210",
+			  "SODIMM_212",
+			  "SODIMM_151",
+			  "SODIMM_153";
+
+	ctrl-sleep-moci-hog {
+		gpio-hog;
+		/* Verdin CTRL_SLEEP_MOCI# (SODIMM 256) */
+		gpios = <1 GPIO_ACTIVE_HIGH>;
+		line-name = "CTRL_SLEEP_MOCI#";
+		output-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ctrl_sleep_moci>;
+	};
+};
+
+/* On-module I2C */
+&i2c1 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	pinctrl-1 = <&pinctrl_i2c1_gpio>;
+	scl-gpios = <&gpio5 14 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio5 15 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "okay";
+
+	pca9450: pmic@25 {
+		compatible = "nxp,pca9450a";
+		interrupt-parent = <&gpio1>;
+		/* PMIC PCA9450 PMIC_nINT GPIO1_IO3 */
+		interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_pmic>;
+		reg = <0x25>;
+		sd-vsel-gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>;
+
+		/*
+		 * The bootloader is expected to switch on the I2C level shifter for the TLA2024 ADC
+		 * behind this PMIC.
+		 */
+
+		regulators {
+			reg_vdd_soc: BUCK1 {
+				nxp,dvs-run-voltage = <850000>;
+				nxp,dvs-standby-voltage = <800000>;
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <850000>;
+				regulator-min-microvolt = <800000>;
+				regulator-name = "On-module +VDD_SOC (BUCK1)";
+				regulator-ramp-delay = <3125>;
+			};
+
+			reg_vdd_arm: BUCK2 {
+				nxp,dvs-run-voltage = <950000>;
+				nxp,dvs-standby-voltage = <850000>;
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1050000>;
+				regulator-min-microvolt = <805000>;
+				regulator-name = "On-module +VDD_ARM (BUCK2)";
+				regulator-ramp-delay = <3125>;
+			};
+
+			reg_vdd_dram: BUCK3 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1000000>;
+				regulator-min-microvolt = <805000>;
+				regulator-name = "On-module +VDD_GPU_VPU_DDR (BUCK3)";
+			};
+
+			reg_vdd_3v3: BUCK4 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <3300000>;
+				regulator-min-microvolt = <3300000>;
+				regulator-name = "On-module +V3.3 (BUCK4)";
+			};
+
+			reg_vdd_1v8: BUCK5 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1800000>;
+				regulator-min-microvolt = <1800000>;
+				regulator-name = "PWR_1V8_MOCI (BUCK5)";
+			};
+
+			reg_nvcc_dram: BUCK6 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1100000>;
+				regulator-min-microvolt = <1100000>;
+				regulator-name = "On-module +VDD_DDR (BUCK6)";
+			};
+
+			reg_nvcc_snvs: LDO1 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1800000>;
+				regulator-min-microvolt = <1800000>;
+				regulator-name = "On-module +V1.8_SNVS (LDO1)";
+			};
+
+			reg_vdd_snvs: LDO2 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <800000>;
+				regulator-min-microvolt = <800000>;
+				regulator-name = "On-module +V0.8_SNVS (LDO2)";
+			};
+
+			reg_vdda: LDO3 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1800000>;
+				regulator-min-microvolt = <1800000>;
+				regulator-name = "On-module +V1.8A (LDO3)";
+			};
+
+			reg_vdd_phy: LDO4 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <900000>;
+				regulator-min-microvolt = <900000>;
+				regulator-name = "On-module +V0.9_MIPI (LDO4)";
+			};
+
+			reg_nvcc_sd: LDO5 {
+				regulator-max-microvolt = <3300000>;
+				regulator-min-microvolt = <1800000>;
+				regulator-name = "On-module +V3.3_1.8_SD (LDO5)";
+			};
+		};
+	};
+
+	rtc_i2c: rtc@32 {
+		compatible = "epson,rx8130";
+		reg = <0x32>;
+	};
+
+	adc@49 {
+		compatible = "ti,ads1015";
+		reg = <0x49>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* Verdin I2C_1 (ADC_4 - ADC_3) */
+		channel@0 {
+			reg = <0>;
+			ti,datarate = <4>;
+			ti,gain = <2>;
+		};
+
+		/* Verdin I2C_1 (ADC_4 - ADC_1) */
+		channel@1 {
+			reg = <1>;
+			ti,datarate = <4>;
+			ti,gain = <2>;
+		};
+
+		/* Verdin I2C_1 (ADC_3 - ADC_1) */
+		channel@2 {
+			reg = <2>;
+			ti,datarate = <4>;
+			ti,gain = <2>;
+		};
+
+		/* Verdin I2C_1 (ADC_2 - ADC_1) */
+		channel@3 {
+			reg = <3>;
+			ti,datarate = <4>;
+			ti,gain = <2>;
+		};
+
+		/* Verdin I2C_1 ADC_4 */
+		channel@4 {
+			reg = <4>;
+			ti,datarate = <4>;
+			ti,gain = <2>;
+		};
+
+		/* Verdin I2C_1 ADC_3 */
+		channel@5 {
+			reg = <5>;
+			ti,datarate = <4>;
+			ti,gain = <2>;
+		};
+
+		/* Verdin I2C_1 ADC_2 */
+		channel@6 {
+			reg = <6>;
+			ti,datarate = <4>;
+			ti,gain = <2>;
+		};
+
+		/* Verdin I2C_1 ADC_1 */
+		channel@7 {
+			reg = <7>;
+			ti,datarate = <4>;
+			ti,gain = <2>;
+		};
+	};
+
+	eeprom@50 {
+		compatible = "st,24c02";
+		pagesize = <16>;
+		reg = <0x50>;
+	};
+};
+
+/* Verdin I2C_2_DSI */
+&i2c2 {
+	clock-frequency = <10000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	pinctrl-1 = <&pinctrl_i2c2_gpio>;
+	scl-gpios = <&gpio5 16 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio5 17 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "disabled";
+};
+
+/* Verdin I2C_3_HDMI N/A */
+
+/* Verdin I2C_4_CSI */
+&i2c3 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	pinctrl-1 = <&pinctrl_i2c3_gpio>;
+	scl-gpios = <&gpio5 18 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio5 19 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+};
+
+/* Verdin I2C_1 */
+&i2c4 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c4>;
+	pinctrl-1 = <&pinctrl_i2c4_gpio>;
+	scl-gpios = <&gpio5 20 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio5 21 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+
+	gpio_expander_21: gpio-expander@21 {
+		compatible = "nxp,pcal6416";
+		#gpio-cells = <2>;
+		gpio-controller;
+		reg = <0x21>;
+		vcc-supply = <&reg_3p3v>;
+		status = "disabled";
+	};
+
+	lvds_ti_sn65dsi84: bridge@2c {
+		compatible = "ti,sn65dsi84";
+		/* Verdin GPIO_9_DSI (SN65DSI84 IRQ, SODIMM 17, unused) */
+		/* Verdin GPIO_10_DSI (SODIMM 21) */
+		enable-gpios = <&gpio3 3 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_10_dsi>;
+		reg = <0x2c>;
+		status = "disabled";
+	};
+
+	/* Current measurement into module VCC */
+	hwmon: hwmon@40 {
+		compatible = "ti,ina219";
+		reg = <0x40>;
+		shunt-resistor = <10000>;
+		status = "disabled";
+	};
+
+	hdmi_lontium_lt8912: hdmi@48 {
+		compatible = "lontium,lt8912b";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_10_dsi>, <&pinctrl_pwm_3_dsi_hpd_gpio>;
+		reg = <0x48>;
+		/* Verdin GPIO_9_DSI (LT8912 INT, SODIMM 17, unused) */
+		/* Verdin GPIO_10_DSI (SODIMM 21) */
+		reset-gpios = <&gpio3 3 GPIO_ACTIVE_LOW>;
+		status = "disabled";
+	};
+
+	atmel_mxt_ts: touch@4a {
+		compatible = "atmel,maxtouch";
+		/*
+		 * Verdin GPIO_9_DSI
+		 * (TOUCH_INT#, SODIMM 17, also routed to SN65DSI83 IRQ albeit currently unused)
+		 */
+		interrupt-parent = <&gpio3>;
+		interrupts = <15 IRQ_TYPE_EDGE_FALLING>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_9_dsi>, <&pinctrl_i2s_2_bclk_touch_reset>;
+		reg = <0x4a>;
+		/* Verdin I2S_2_BCLK (TOUCH_RESET#, SODIMM 42) */
+		reset-gpios = <&gpio3 23 GPIO_ACTIVE_LOW>;
+		status = "disabled";
+	};
+
+	/* Temperature sensor on carrier board */
+	hwmon_temp: sensor@4f {
+		compatible = "ti,tmp75c";
+		reg = <0x4f>;
+		status = "disabled";
+	};
+
+	/* EEPROM on display adapter (MIPI DSI Display Adapter) */
+	eeprom_display_adapter: eeprom@50 {
+		compatible = "st,24c02";
+		pagesize = <16>;
+		reg = <0x50>;
+		status = "disabled";
+	};
+
+	/* EEPROM on carrier board */
+	eeprom_carrier_board: eeprom@57 {
+		compatible = "st,24c02";
+		pagesize = <16>;
+		reg = <0x57>;
+		status = "disabled";
+	};
+};
+
+/* Verdin PCIE_1 */
+&pcie0 {
+	assigned-clocks = <&clk IMX8MM_CLK_PCIE1_AUX>,
+			  <&clk IMX8MM_CLK_PCIE1_CTRL>;
+	assigned-clock-parents = <&clk IMX8MM_SYS_PLL2_50M>,
+				 <&clk IMX8MM_SYS_PLL2_250M>;
+	assigned-clock-rates = <10000000>, <250000000>;
+	clocks = <&clk IMX8MM_CLK_PCIE1_ROOT>, <&clk IMX8MM_CLK_PCIE1_AUX>,
+		 <&clk IMX8MM_CLK_PCIE1_PHY>;
+	clock-names = "pcie", "pcie_aux", "pcie_bus";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pcie0>;
+	/* PCIE_1_RESET# (SODIMM 244) */
+	reset-gpio = <&gpio3 19 GPIO_ACTIVE_LOW>;
+};
+
+&pcie_phy {
+	clocks = <&clk IMX8MM_CLK_PCIE1_PHY>;
+	fsl,clkreq-unsupported;
+	fsl,refclk-pad-mode = <IMX8_PCIE_REFCLK_PAD_OUTPUT>;
+	fsl,tx-deemph-gen1 = <0x2d>;
+	fsl,tx-deemph-gen2 = <0xf>;
+};
+
+/* Verdin PWM_3_DSI */
+&pwm1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm_1>;
+	#pwm-cells = <3>;
+};
+
+/* Verdin PWM_1 */
+&pwm2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm_2>;
+	#pwm-cells = <3>;
+};
+
+/* Verdin PWM_2 */
+&pwm3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm_3>;
+	#pwm-cells = <3>;
+};
+
+/* Verdin I2S_1 */
+&sai2 {
+	#sound-dai-cells = <0>;
+	assigned-clock-parents = <&clk IMX8MM_AUDIO_PLL1_OUT>;
+	assigned-clock-rates = <24576000>;
+	assigned-clocks = <&clk IMX8MM_CLK_SAI2>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sai2>;
+};
+
+&snvs_pwrkey {
+	status = "okay";
+};
+
+/* Verdin UART_3, used as the Linux console */
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+};
+
+/* Verdin UART_1 */
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	uart-has-rtscts;
+};
+
+/* Verdin UART_2 */
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	uart-has-rtscts;
+};
+
+/*
+ * Verdin UART_4
+ * Resource allocated to M4 by default, must not be accessed from Cortex-A35 or you get an OOPS
+ */
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+};
+
+/* Verdin USB_1 */
+&usbotg1 {
+	adp-disable;
+	dr_mode = "otg";
+	hnp-disable;
+	over-current-active-low;
+	samsung,picophy-dc-vol-level-adjust = <7>;
+	samsung,picophy-pre-emp-curr-control = <3>;
+	srp-disable;
+	vbus-supply = <&reg_usb_otg1_vbus>;
+};
+
+/* Verdin USB_2 */
+&usbotg2 {
+	dr_mode = "host";
+	over-current-active-low;
+	samsung,picophy-dc-vol-level-adjust = <7>;
+	samsung,picophy-pre-emp-curr-control = <3>;
+	vbus-supply = <&reg_usb_otg2_vbus>;
+};
+
+&usbphynop1 {
+	vcc-supply = <&reg_vdd_3v3>;
+};
+
+&usbphynop2 {
+	power-domains = <&pgc_otg2>;
+	vcc-supply = <&reg_vdd_3v3>;
+};
+
+/* On-module eMMC */
+&usdhc1 {
+	bus-width = <8>;
+	keep-power-in-suspend;
+	non-removable;
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
+	status = "okay";
+};
+
+/* Verdin SD_1 */
+&usdhc2 {
+	bus-width = <4>;
+	cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
+	disable-wp;
+	pinctrl-names = "default", "state_100mhz", "state_200mhz", "sleep";
+	pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_cd>;
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_cd>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_cd>;
+	pinctrl-3 = <&pinctrl_usdhc2_sleep>, <&pinctrl_usdhc2_cd_sleep>;
+	vmmc-supply = <&reg_usdhc2_vmmc>;
+};
+
+&wdog1 {
+	fsl,ext-reset-output;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog>;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpio1>, <&pinctrl_gpio2>,
+		    <&pinctrl_gpio3>, <&pinctrl_gpio4>,
+		    <&pinctrl_gpio7>, <&pinctrl_gpio8>,
+		    <&pinctrl_gpio_hog1>, <&pinctrl_gpio_hog2>, <&pinctrl_gpio_hog3>,
+		    <&pinctrl_pmic_tpm_ena>;
+
+	pinctrl_can1_int: can1intgrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_GPIO1_IO06_GPIO1_IO6		0x146>;	/* CAN_1_SPI_INT#_1.8V */
+	};
+
+	pinctrl_can2_int: can2intgrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_GPIO1_IO07_GPIO1_IO7		0x106>;	/* CAN_2_SPI_INT#_1.8V, unused */
+	};
+
+	pinctrl_ctrl_sleep_moci: ctrlsleepmocigrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_SAI3_TXD_GPIO5_IO1		0x106>;	/* SODIMM 256 */
+	};
+
+	pinctrl_ecspi2: ecspi2grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_ECSPI2_MISO_ECSPI2_MISO		0x6>,	/* SODIMM 198 */
+			<MX8MM_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI		0x6>,	/* SODIMM 200 */
+			<MX8MM_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK		0x6>,	/* SODIMM 196 */
+			<MX8MM_IOMUXC_ECSPI2_SS0_GPIO5_IO13		0x6>;	/* SODIMM 202 */
+	};
+
+	pinctrl_ecspi3: ecspi3grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_GPIO1_IO05_GPIO1_IO5		0x146>,	/* CAN_2_SPI_CS#_1.8V */
+			<MX8MM_IOMUXC_UART1_RXD_ECSPI3_SCLK		0x6>,	/* CAN_SPI_SCK_1.8V */
+			<MX8MM_IOMUXC_UART1_TXD_ECSPI3_MOSI		0x6>,	/* CAN_SPI_MOSI_1.8V */
+			<MX8MM_IOMUXC_UART2_RXD_ECSPI3_MISO		0x6>,	/* CAN_SPI_MISO_1.8V */
+			<MX8MM_IOMUXC_UART2_TXD_GPIO5_IO25		0x6>;	/* CAN_1_SPI_CS_1.8V# */
+	};
+
+	pinctrl_fec1: fec1grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_ENET_MDC_ENET1_MDC		0x3>,
+			<MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO		0x3>,
+			<MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0		0x91>,
+			<MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1		0x91>,
+			<MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2		0x91>,
+			<MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3		0x91>,
+			<MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC		0x91>,
+			<MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL	0x91>,
+			<MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0		0x1f>,
+			<MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1		0x1f>,
+			<MX8MM_IOMUXC_ENET_TD2_ENET1_RGMII_TD2		0x1f>,
+			<MX8MM_IOMUXC_ENET_TD3_ENET1_RGMII_TD3		0x1f>,
+			<MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC		0x1f>,
+			<MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL	0x1f>,
+			<MX8MM_IOMUXC_GPIO1_IO10_GPIO1_IO10		0x146>;
+	};
+
+	pinctrl_fec1_sleep: fec1-sleepgrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_ENET_MDC_ENET1_MDC		0x3>,
+			<MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO		0x3>,
+			<MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0		0x91>,
+			<MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1		0x91>,
+			<MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2		0x91>,
+			<MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3		0x91>,
+			<MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC		0x91>,
+			<MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL	0x91>,
+			<MX8MM_IOMUXC_ENET_TD0_GPIO1_IO21		0x1f>,
+			<MX8MM_IOMUXC_ENET_TD1_GPIO1_IO20		0x1f>,
+			<MX8MM_IOMUXC_ENET_TD2_GPIO1_IO19		0x1f>,
+			<MX8MM_IOMUXC_ENET_TD3_GPIO1_IO18		0x1f>,
+			<MX8MM_IOMUXC_ENET_TXC_GPIO1_IO23		0x1f>,
+			<MX8MM_IOMUXC_ENET_TX_CTL_GPIO1_IO22		0x1f>,
+			<MX8MM_IOMUXC_GPIO1_IO10_GPIO1_IO10		0x106>;
+	};
+
+	pinctrl_flexspi0: flexspi0grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_NAND_ALE_QSPI_A_SCLK		0x106>,	/* SODIMM 52 */
+			<MX8MM_IOMUXC_NAND_CE0_B_QSPI_A_SS0_B		0x106>,	/* SODIMM 54 */
+			<MX8MM_IOMUXC_NAND_CE1_B_QSPI_A_SS1_B		0x106>,	/* SODIMM 64 */
+			<MX8MM_IOMUXC_NAND_DATA00_QSPI_A_DATA0		0x106>,	/* SODIMM 56 */
+			<MX8MM_IOMUXC_NAND_DATA01_QSPI_A_DATA1		0x106>,	/* SODIMM 58 */
+			<MX8MM_IOMUXC_NAND_DATA02_QSPI_A_DATA2		0x106>,	/* SODIMM 60 */
+			<MX8MM_IOMUXC_NAND_DATA03_QSPI_A_DATA3		0x106>,	/* SODIMM 62 */
+			<MX8MM_IOMUXC_NAND_DQS_QSPI_A_DQS		0x106>;	/* SODIMM 66 */
+	};
+
+	pinctrl_gpio1: gpio1grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_NAND_CE3_B_GPIO3_IO4		0x106>;	/* SODIMM 206 */
+	};
+
+	pinctrl_gpio2: gpio2grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_SPDIF_EXT_CLK_GPIO5_IO5		0x106>;	/* SODIMM 208 */
+	};
+
+	pinctrl_gpio3: gpio3grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_UART3_RXD_GPIO5_IO26		0x106>;	/* SODIMM 210 */
+	};
+
+	pinctrl_gpio4: gpio4grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_UART3_TXD_GPIO5_IO27		0x106>;	/* SODIMM 212 */
+	};
+
+	pinctrl_gpio5: gpio5grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_GPIO1_IO00_GPIO1_IO0		0x106>;	/* SODIMM 216 */
+	};
+
+	pinctrl_gpio6: gpio6grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_GPIO1_IO11_GPIO1_IO11		0x106>;	/* SODIMM 218 */
+	};
+
+	pinctrl_gpio7: gpio7grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_GPIO1_IO08_GPIO1_IO8		0x106>;	/* SODIMM 220 */
+	};
+
+	pinctrl_gpio8: gpio8grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_GPIO1_IO09_GPIO1_IO9		0x106>;	/* SODIMM 222 */
+	};
+
+	/* Verdin GPIO_9_DSI (pulled-up as active-low) */
+	pinctrl_gpio_9_dsi: gpio9dsigrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_NAND_RE_B_GPIO3_IO15		0x146>;	/* SODIMM 17 */
+	};
+
+	/* Verdin GPIO_10_DSI (pulled-up as active-low) */
+	pinctrl_gpio_10_dsi: gpio10dsigrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_NAND_CE2_B_GPIO3_IO3		0x146>;	/* SODIMM 21 */
+	};
+
+	pinctrl_gpio_hog1: gpiohog1grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_SAI1_MCLK_GPIO4_IO20		0x106>,	/* SODIMM 88 */
+			<MX8MM_IOMUXC_SAI1_RXC_GPIO4_IO1		0x106>,	/* SODIMM 90 */
+			<MX8MM_IOMUXC_SAI1_RXD0_GPIO4_IO2		0x106>,	/* SODIMM 92 */
+			<MX8MM_IOMUXC_SAI1_RXD1_GPIO4_IO3		0x106>,	/* SODIMM 94 */
+			<MX8MM_IOMUXC_SAI1_RXD2_GPIO4_IO4		0x106>,	/* SODIMM 96 */
+			<MX8MM_IOMUXC_SAI1_RXD3_GPIO4_IO5		0x106>,	/* SODIMM 100 */
+			<MX8MM_IOMUXC_SAI1_RXFS_GPIO4_IO0		0x106>,	/* SODIMM 102 */
+			<MX8MM_IOMUXC_SAI1_TXC_GPIO4_IO11		0x106>,	/* SODIMM 104 */
+			<MX8MM_IOMUXC_SAI1_TXD0_GPIO4_IO12		0x106>,	/* SODIMM 106 */
+			<MX8MM_IOMUXC_SAI1_TXD1_GPIO4_IO13		0x106>,	/* SODIMM 108 */
+			<MX8MM_IOMUXC_SAI1_TXD2_GPIO4_IO14		0x106>,	/* SODIMM 112 */
+			<MX8MM_IOMUXC_SAI1_TXD3_GPIO4_IO15		0x106>,	/* SODIMM 114 */
+			<MX8MM_IOMUXC_SAI1_TXD4_GPIO4_IO16		0x106>,	/* SODIMM 116 */
+			<MX8MM_IOMUXC_SAI1_TXD6_GPIO4_IO18		0x106>,	/* SODIMM 118 */
+			<MX8MM_IOMUXC_SAI1_TXFS_GPIO4_IO10		0x106>;	/* SODIMM 120 */
+	};
+
+	pinctrl_gpio_hog2: gpiohog2grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_SAI3_MCLK_GPIO5_IO2		0x106>;	/* SODIMM 91 */
+	};
+
+	pinctrl_gpio_hog3: gpiohog3grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_GPIO1_IO13_GPIO1_IO13		0x146>,	/* SODIMM 157 */
+			<MX8MM_IOMUXC_GPIO1_IO15_GPIO1_IO15		0x146>;	/* SODIMM 187 */
+	};
+
+	pinctrl_gpio_keys: gpiokeysgrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_SAI3_RXFS_GPIO4_IO28		0x146>;	/* SODIMM 252 */
+	};
+
+	/* On-module I2C */
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL			0x40000146>,	/* PMIC_I2C_SCL */
+			<MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA			0x40000146>;	/* PMIC_I2C_SDA */
+	};
+
+	pinctrl_i2c1_gpio: i2c1gpiogrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_I2C1_SCL_GPIO5_IO14		0x146>,	/* PMIC_I2C_SCL */
+			<MX8MM_IOMUXC_I2C1_SDA_GPIO5_IO15		0x146>;	/* PMIC_I2C_SDA */
+	};
+
+	/* Verdin I2C_4_CSI */
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_I2C2_SCL_I2C2_SCL			0x40000146>,	/* SODIMM 55 */
+			<MX8MM_IOMUXC_I2C2_SDA_I2C2_SDA			0x40000146>;	/* SODIMM 53 */
+	};
+
+	pinctrl_i2c2_gpio: i2c2gpiogrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_I2C2_SCL_GPIO5_IO16		0x146>,	/* SODIMM 55 */
+			<MX8MM_IOMUXC_I2C2_SDA_GPIO5_IO17		0x146>;	/* SODIMM 53 */
+	};
+
+	/* Verdin I2C_2_DSI */
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_I2C3_SCL_I2C3_SCL			0x40000146>,	/* SODIMM 95 */
+			<MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA			0x40000146>;	/* SODIMM 93 */
+	};
+
+	pinctrl_i2c3_gpio: i2c3gpiogrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_I2C3_SCL_GPIO5_IO18		0x146>,	/* SODIMM 95 */
+			<MX8MM_IOMUXC_I2C3_SDA_GPIO5_IO19		0x146>;	/* SODIMM 93 */
+	};
+
+	/* Verdin I2C_1 */
+	pinctrl_i2c4: i2c4grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_I2C4_SCL_I2C4_SCL			0x40000146>,	/* SODIMM 14 */
+			<MX8MM_IOMUXC_I2C4_SDA_I2C4_SDA			0x40000146>;	/* SODIMM 12 */
+	};
+
+	pinctrl_i2c4_gpio: i2c4gpiogrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_I2C4_SCL_GPIO5_IO20		0x146>,	/* SODIMM 14 */
+			<MX8MM_IOMUXC_I2C4_SDA_GPIO5_IO21		0x146>;	/* SODIMM 12 */
+	};
+
+	/* Verdin I2S_2_BCLK (TOUCH_RESET#) */
+	pinctrl_i2s_2_bclk_touch_reset: i2s2bclktouchresetgrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_SAI5_RXD2_GPIO3_IO23		0x6>;	/* SODIMM 42 */
+	};
+
+	/* Verdin I2S_2_D_OUT shared with SAI5 */
+	pinctrl_i2s_2_d_out_dsi_1_bkl_en: i2s2doutdsi1bklengrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_SAI5_RXD3_GPIO3_IO24		0x6>;	/* SODIMM 46 */
+	};
+
+	pinctrl_pcie0: pcie0grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_SAI5_RXFS_GPIO3_IO19		0x6>,	/* SODIMM 244 */
+			/* PMIC_EN_PCIe_CLK, unused */
+			<MX8MM_IOMUXC_SD2_RESET_B_GPIO2_IO19		0x6>;
+	};
+
+	pinctrl_pmic: pmicirqgrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3		0x141>;	/* PMIC_INT# */
+	};
+
+	/* Verdin PWM_3_DSI shared with GPIO1_IO1 */
+	pinctrl_pwm_1: pwm1grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_GPIO1_IO01_PWM1_OUT		0x6>;	/* SODIMM 19 */
+	};
+
+	pinctrl_pwm_2: pwm2grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_SPDIF_RX_PWM2_OUT			0x6>;	/* SODIMM 15 */
+	};
+
+	pinctrl_pwm_3: pwm3grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_SPDIF_TX_PWM3_OUT			0x6>;	/* SODIMM 16 */
+	};
+
+	/* Verdin PWM_3_DSI (pulled-down as active-high) shared with PWM1_OUT */
+	pinctrl_pwm_3_dsi_hpd_gpio: pwm3dsihpdgpiogrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_GPIO1_IO01_GPIO1_IO1		0x106>;	/* SODIMM 19 */
+	};
+
+	pinctrl_reg_eth: regethgrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_SD2_WP_GPIO2_IO20			0x146>;	/* PMIC_EN_ETH */
+	};
+
+	pinctrl_reg_usb1_en: regusb1engrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_GPIO1_IO12_GPIO1_IO12		0x106>;	/* SODIMM 155 */
+	};
+
+	pinctrl_reg_usb2_en: regusb2engrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_GPIO1_IO14_GPIO1_IO14		0x106>;	/* SODIMM 185 */
+	};
+
+	pinctrl_sai2: sai2grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_SAI2_MCLK_SAI2_MCLK		0x6>,	/* SODIMM 38 */
+			<MX8MM_IOMUXC_SAI2_TXC_SAI2_TX_BCLK		0x6>,	/* SODIMM 30 */
+			<MX8MM_IOMUXC_SAI2_TXFS_SAI2_TX_SYNC		0x6>,	/* SODIMM 32 */
+			<MX8MM_IOMUXC_SAI2_RXD0_SAI2_RX_DATA0		0x6>,	/* SODIMM 36 */
+			<MX8MM_IOMUXC_SAI2_TXD0_SAI2_TX_DATA0		0x6>;	/* SODIMM 34 */
+	};
+
+	pinctrl_sai5: sai5grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_SAI5_RXD0_SAI5_RX_DATA0		0x6>,	/* SODIMM 48 */
+			<MX8MM_IOMUXC_SAI5_RXD1_SAI5_TX_SYNC		0x6>,	/* SODIMM 44 */
+			<MX8MM_IOMUXC_SAI5_RXD2_SAI5_TX_BCLK		0x6>,	/* SODIMM 42 */
+			<MX8MM_IOMUXC_SAI5_RXD3_SAI5_TX_DATA0		0x6>;	/* SODIMM 46 */
+	};
+
+	/* control signal for optional ATTPM20P or SE050 */
+	pinctrl_pmic_tpm_ena: pmictpmenagrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_SAI1_TXD7_GPIO4_IO19		0x106>;	/* PMIC_TPM_ENA */
+	};
+
+	pinctrl_tsp: tspgrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_SAI1_RXD4_GPIO4_IO6		0x6>,	/* SODIMM 148 */
+			<MX8MM_IOMUXC_SAI1_RXD5_GPIO4_IO7		0x6>,	/* SODIMM 152 */
+			<MX8MM_IOMUXC_SAI1_RXD6_GPIO4_IO8		0x6>,	/* SODIMM 154 */
+			<MX8MM_IOMUXC_SAI1_RXD7_GPIO4_IO9		0x146>,	/* SODIMM 174 */
+			<MX8MM_IOMUXC_SAI1_TXD5_GPIO4_IO17		0x6>;	/* SODIMM 150 */
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_SAI2_RXC_UART1_DCE_RX		0x146>,	/* SODIMM 147 */
+			<MX8MM_IOMUXC_SAI2_RXFS_UART1_DCE_TX		0x146>;	/* SODIMM 149 */
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_SAI3_RXC_UART2_DCE_CTS_B		0x146>,	/* SODIMM 133 */
+			<MX8MM_IOMUXC_SAI3_RXD_UART2_DCE_RTS_B		0x146>,	/* SODIMM 135 */
+			<MX8MM_IOMUXC_SAI3_TXC_UART2_DCE_TX		0x146>,	/* SODIMM 131 */
+			<MX8MM_IOMUXC_SAI3_TXFS_UART2_DCE_RX		0x146>;	/* SODIMM 129 */
+	};
+
+	pinctrl_uart3: uart3grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_ECSPI1_MISO_UART3_DCE_CTS_B	0x146>,	/* SODIMM 141 */
+			<MX8MM_IOMUXC_ECSPI1_MOSI_UART3_DCE_TX		0x146>,	/* SODIMM 139 */
+			<MX8MM_IOMUXC_ECSPI1_SCLK_UART3_DCE_RX		0x146>,	/* SODIMM 137 */
+			<MX8MM_IOMUXC_ECSPI1_SS0_UART3_DCE_RTS_B	0x146>;	/* SODIMM 143 */
+	};
+
+	pinctrl_uart4: uart4grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_UART4_RXD_UART4_DCE_RX		0x146>,	/* SODIMM 151 */
+			<MX8MM_IOMUXC_UART4_TXD_UART4_DCE_TX		0x146>;	/* SODIMM 153 */
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK		0x190>,
+			<MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD		0x1d0>,
+			<MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0		0x1d0>,
+			<MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1		0x1d0>,
+			<MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2		0x1d0>,
+			<MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3		0x1d0>,
+			<MX8MM_IOMUXC_SD1_DATA4_USDHC1_DATA4		0x1d0>,
+			<MX8MM_IOMUXC_SD1_DATA5_USDHC1_DATA5		0x1d0>,
+			<MX8MM_IOMUXC_SD1_DATA6_USDHC1_DATA6		0x1d0>,
+			<MX8MM_IOMUXC_SD1_DATA7_USDHC1_DATA7		0x1d0>,
+			<MX8MM_IOMUXC_SD1_RESET_B_USDHC1_RESET_B	0x1d1>,
+			<MX8MM_IOMUXC_SD1_STROBE_USDHC1_STROBE		0x190>;
+	};
+
+	pinctrl_usdhc1_100mhz: usdhc1-100mhzgrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK		0x194>,
+			<MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD		0x1d4>,
+			<MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0		0x1d4>,
+			<MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1		0x1d4>,
+			<MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2		0x1d4>,
+			<MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3		0x1d4>,
+			<MX8MM_IOMUXC_SD1_DATA4_USDHC1_DATA4		0x1d4>,
+			<MX8MM_IOMUXC_SD1_DATA5_USDHC1_DATA5		0x1d4>,
+			<MX8MM_IOMUXC_SD1_DATA6_USDHC1_DATA6		0x1d4>,
+			<MX8MM_IOMUXC_SD1_DATA7_USDHC1_DATA7		0x1d4>,
+			<MX8MM_IOMUXC_SD1_RESET_B_USDHC1_RESET_B	0x1d1>,
+			<MX8MM_IOMUXC_SD1_STROBE_USDHC1_STROBE		0x194>;
+	};
+
+	pinctrl_usdhc1_200mhz: usdhc1-200mhzgrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK		0x196>,
+			<MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD		0x1d6>,
+			<MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0		0x1d6>,
+			<MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1		0x1d6>,
+			<MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2		0x1d6>,
+			<MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3		0x1d6>,
+			<MX8MM_IOMUXC_SD1_DATA4_USDHC1_DATA4		0x1d6>,
+			<MX8MM_IOMUXC_SD1_DATA5_USDHC1_DATA5		0x1d6>,
+			<MX8MM_IOMUXC_SD1_DATA6_USDHC1_DATA6		0x1d6>,
+			<MX8MM_IOMUXC_SD1_DATA7_USDHC1_DATA7		0x1d6>,
+			<MX8MM_IOMUXC_SD1_RESET_B_USDHC1_RESET_B	0x1d1>,
+			<MX8MM_IOMUXC_SD1_STROBE_USDHC1_STROBE		0x196>;
+	};
+
+	pinctrl_usdhc2_cd: usdhc2cdgrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x6>;	/* SODIMM 84 */
+	};
+
+	pinctrl_usdhc2_cd_sleep: usdhc2cdslpgrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12		0x0>;	/* SODIMM 84 */
+	};
+
+	pinctrl_usdhc2_pwr_en: usdhc2pwrengrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_NAND_CLE_GPIO3_IO5		0x6>;	/* SODIMM 76 */
+	};
+
+	/*
+	 * Note: Due to ERR050080 we use discrete external on-module resistors pulling-up to the
+	 * on-module +V3.3_1.8_SD (LDO5) rail and explicitly disable the internal pull-ups here.
+	 */
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0x10>,
+			<MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK		0x90>,	/* SODIMM 78 */
+			<MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD		0x90>,	/* SODIMM 74 */
+			<MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x90>,	/* SODIMM 80 */
+			<MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x90>,	/* SODIMM 82 */
+			<MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x90>,	/* SODIMM 70 */
+			<MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x90>;	/* SODIMM 72 */
+	};
+
+	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0x10>,
+			<MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK		0x94>,
+			<MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD		0x94>,
+			<MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x94>,
+			<MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x94>,
+			<MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x94>,
+			<MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x94>;
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0x10>,
+			<MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK		0x96>,
+			<MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD		0x96>,
+			<MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x96>,
+			<MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x96>,
+			<MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x96>,
+			<MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x96>;
+	};
+
+	/* Avoid backfeeding with removed card power */
+	pinctrl_usdhc2_sleep: usdhc2slpgrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_GPIO1_IO04_USDHC2_VSELECT		0x0>,
+			<MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK		0x0>,
+			<MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD		0x0>,
+			<MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x0>,
+			<MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x0>,
+			<MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x0>,
+			<MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x0>;
+	};
+
+	/*
+	 * On-module Wi-Fi/BT or type specific SDHC interface
+	 * (e.g. on X52 extension slot of Verdin Development Board)
+	 */
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins =
+			<MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0		0x150>,
+			<MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1		0x150>,
+			<MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2		0x150>,
+			<MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3		0x150>,
+			<MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK		0x150>,
+			<MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD		0x150>;
+	};
+
+	pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0		0x154>,
+			<MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1		0x154>,
+			<MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2		0x154>,
+			<MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3		0x154>,
+			<MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK		0x154>,
+			<MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD		0x154>;
+	};
+
+	pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0		0x156>,
+			<MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1		0x156>,
+			<MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2		0x156>,
+			<MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3		0x156>,
+			<MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK		0x156>,
+			<MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD		0x156>;
+	};
+
+	pinctrl_wdog: wdoggrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B		0x166>;	/* PMIC_WDI */
+	};
+
+	pinctrl_wifi_ctrl: wifictrlgrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_NAND_READY_B_GPIO3_IO16		0x46>,	/* WIFI_WKUP_BT */
+			<MX8MM_IOMUXC_SAI1_RXD7_GPIO4_IO9		0x146>,	/* WIFI_W_WKUP_HOST */
+			<MX8MM_IOMUXC_SAI5_RXC_GPIO3_IO20		0x46>;	/* WIFI_WKUP_WLAN */
+	};
+
+	pinctrl_wifi_i2s: bti2sgrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_SAI1_RXD4_SAI6_TX_BCLK		0x6>,	/* WIFI_TX_BCLK */
+			<MX8MM_IOMUXC_SAI1_RXD5_SAI6_TX_DATA0		0x6>,	/* WIFI_TX_DATA0 */
+			<MX8MM_IOMUXC_SAI1_RXD6_SAI6_TX_SYNC		0x6>,	/* WIFI_TX_SYNC */
+			<MX8MM_IOMUXC_SAI1_TXD5_SAI6_RX_DATA0		0x6>;	/* WIFI_RX_DATA0 */
+	};
+
+	pinctrl_wifi_pwr_en: wifipwrengrp {
+		fsl,pins =
+			<MX8MM_IOMUXC_SAI5_MCLK_GPIO3_IO25		0x6>;	/* PMIC_EN_WIFI */
+	};
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mm.dtsi b/arch/arm64/boot/dts/freescale/imx8mm.dtsi
index c2f3f118f82e..dabd94dc30c4 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm.dtsi
@@ -65,6 +65,12 @@
 			clock-latency = <61036>; /* two CLK32 periods */
 			clocks = <&clk IMX8MM_CLK_ARM>;
 			enable-method = "psci";
+			i-cache-size = <0x8000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <128>;
 			next-level-cache = <&A53_L2>;
 			operating-points-v2 = <&a53_opp_table>;
 			nvmem-cells = <&cpu_speed_grade>;
@@ -80,6 +86,12 @@
 			clock-latency = <61036>; /* two CLK32 periods */
 			clocks = <&clk IMX8MM_CLK_ARM>;
 			enable-method = "psci";
+			i-cache-size = <0x8000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <128>;
 			next-level-cache = <&A53_L2>;
 			operating-points-v2 = <&a53_opp_table>;
 			cpu-idle-states = <&cpu_pd_wait>;
@@ -93,6 +105,12 @@
 			clock-latency = <61036>; /* two CLK32 periods */
 			clocks = <&clk IMX8MM_CLK_ARM>;
 			enable-method = "psci";
+			i-cache-size = <0x8000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <128>;
 			next-level-cache = <&A53_L2>;
 			operating-points-v2 = <&a53_opp_table>;
 			cpu-idle-states = <&cpu_pd_wait>;
@@ -106,6 +124,12 @@
 			clock-latency = <61036>; /* two CLK32 periods */
 			clocks = <&clk IMX8MM_CLK_ARM>;
 			enable-method = "psci";
+			i-cache-size = <0x8000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <128>;
 			next-level-cache = <&A53_L2>;
 			operating-points-v2 = <&a53_opp_table>;
 			cpu-idle-states = <&cpu_pd_wait>;
@@ -114,6 +138,10 @@
 
 		A53_L2: l2-cache0 {
 			compatible = "cache";
+			cache-level = <2>;
+			cache-size = <0x80000>;
+			cache-line-size = <64>;
+			cache-sets = <512>;
 		};
 	};
 
@@ -184,7 +212,7 @@
 	clk_ext4: clock-ext4 {
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
-		clock-frequency= <133000000>;
+		clock-frequency = <133000000>;
 		clock-output-names = "clk_ext4";
 	};
 
@@ -248,6 +276,7 @@
 		assigned-clocks = <&clk IMX8MM_CLK_USB_PHY_REF>;
 		assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_100M>;
 		clock-names = "main_clk";
+		power-domains = <&pgc_otg1>;
 	};
 
 	usbphynop2: usbphynop2 {
@@ -257,9 +286,10 @@
 		assigned-clocks = <&clk IMX8MM_CLK_USB_PHY_REF>;
 		assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_100M>;
 		clock-names = "main_clk";
+		power-domains = <&pgc_otg2>;
 	};
 
-	soc@0 {
+	soc: soc@0 {
 		compatible = "fsl,imx8mm-soc", "simple-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -520,7 +550,7 @@
 			};
 
 			gpr: iomuxc-gpr@30340000 {
-				compatible = "fsl,imx8mm-iomuxc-gpr", "syscon";
+				compatible = "fsl,imx8mm-iomuxc-gpr", "fsl,imx6q-iomuxc-gpr", "syscon";
 				reg = <0x30340000 0x10000>;
 			};
 
@@ -574,6 +604,11 @@
 					wakeup-source;
 					status = "disabled";
 				};
+
+				snvs_lpgpr: snvs-lpgpr {
+					compatible = "fsl,imx8mm-snvs-lpgpr",
+						     "fsl,imx7d-snvs-lpgpr";
+				};
 			};
 
 			clk: clock-controller@30380000 {
@@ -591,8 +626,7 @@
 						<&clk IMX8MM_CLK_IPG_AUDIO_ROOT>,
 						<&clk IMX8MM_SYS_PLL3>,
 						<&clk IMX8MM_VIDEO_PLL1>,
-						<&clk IMX8MM_AUDIO_PLL1>,
-						<&clk IMX8MM_AUDIO_PLL2>;
+						<&clk IMX8MM_AUDIO_PLL1>;
 				assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_800M>,
 							 <&clk IMX8MM_ARM_PLL_OUT>,
 							 <&clk IMX8MM_SYS_PLL3_OUT>,
@@ -602,8 +636,7 @@
 							<400000000>,
 							<750000000>,
 							<594000000>,
-							<393216000>,
-							<361267200>;
+							<393216000>;
 			};
 
 			src: reset-controller@30390000 {
@@ -643,13 +676,11 @@
 					pgc_otg1: power-domain@2 {
 						#power-domain-cells = <0>;
 						reg = <IMX8MM_POWER_DOMAIN_OTG1>;
-						power-domains = <&pgc_hsiomix>;
 					};
 
 					pgc_otg2: power-domain@3 {
 						#power-domain-cells = <0>;
 						reg = <IMX8MM_POWER_DOMAIN_OTG2>;
-						power-domains = <&pgc_hsiomix>;
 					};
 
 					pgc_gpumix: power-domain@4 {
@@ -681,7 +712,6 @@
 						clocks = <&clk IMX8MM_CLK_VPU_DEC_ROOT>;
 						assigned-clocks = <&clk IMX8MM_CLK_VPU_BUS>;
 						assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_800M>;
-						resets = <&src IMX8MQ_RESET_VPU_RESET>;
 					};
 
 					pgc_vpu_g1: power-domain@7 {
@@ -733,7 +763,7 @@
 				clocks = <&clk IMX8MM_CLK_PWM1_ROOT>,
 					<&clk IMX8MM_CLK_PWM1_ROOT>;
 				clock-names = "ipg", "per";
-				#pwm-cells = <2>;
+				#pwm-cells = <3>;
 				status = "disabled";
 			};
 
@@ -744,7 +774,7 @@
 				clocks = <&clk IMX8MM_CLK_PWM2_ROOT>,
 					 <&clk IMX8MM_CLK_PWM2_ROOT>;
 				clock-names = "ipg", "per";
-				#pwm-cells = <2>;
+				#pwm-cells = <3>;
 				status = "disabled";
 			};
 
@@ -755,7 +785,7 @@
 				clocks = <&clk IMX8MM_CLK_PWM3_ROOT>,
 					 <&clk IMX8MM_CLK_PWM3_ROOT>;
 				clock-names = "ipg", "per";
-				#pwm-cells = <2>;
+				#pwm-cells = <3>;
 				status = "disabled";
 			};
 
@@ -766,7 +796,7 @@
 				clocks = <&clk IMX8MM_CLK_PWM4_ROOT>,
 					 <&clk IMX8MM_CLK_PWM4_ROOT>;
 				clock-names = "ipg", "per";
-				#pwm-cells = <2>;
+				#pwm-cells = <3>;
 				status = "disabled";
 			};
 
@@ -886,6 +916,7 @@
 					compatible = "fsl,sec-v4.0-job-ring";
 					reg = <0x1000 0x1000>;
 					interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>;
+					status = "disabled";
 				};
 
 				sec_jr1: jr@2000 {
@@ -970,7 +1001,7 @@
 					 <&clk IMX8MM_CLK_USDHC1_ROOT>;
 				clock-names = "ipg", "ahb", "per";
 				fsl,tuning-start-tap = <20>;
-				fsl,tuning-step= <2>;
+				fsl,tuning-step = <2>;
 				bus-width = <4>;
 				status = "disabled";
 			};
@@ -984,7 +1015,7 @@
 					 <&clk IMX8MM_CLK_USDHC2_ROOT>;
 				clock-names = "ipg", "ahb", "per";
 				fsl,tuning-start-tap = <20>;
-				fsl,tuning-step= <2>;
+				fsl,tuning-step = <2>;
 				bus-width = <4>;
 				status = "disabled";
 			};
@@ -998,7 +1029,7 @@
 					 <&clk IMX8MM_CLK_USDHC3_ROOT>;
 				clock-names = "ipg", "ahb", "per";
 				fsl,tuning-start-tap = <20>;
-				fsl,tuning-step= <2>;
+				fsl,tuning-step = <2>;
 				bus-width = <4>;
 				status = "disabled";
 			};
@@ -1054,7 +1085,6 @@
 				fsl,num-rx-queues = <3>;
 				nvmem-cells = <&fec_mac_address>;
 				nvmem-cell-names = "mac-address";
-				nvmem_macaddr_swap;
 				fsl,stop-mode = <&gpr 0x10 3>;
 				status = "disabled";
 			};
@@ -1068,6 +1098,22 @@
 			#size-cells = <1>;
 			ranges = <0x32c00000 0x32c00000 0x400000>;
 
+			csi: csi@32e20000 {
+				compatible = "fsl,imx8mm-csi", "fsl,imx7-csi";
+				reg = <0x32e20000 0x1000>;
+				interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clk IMX8MM_CLK_CSI1_ROOT>;
+				clock-names = "mclk";
+				power-domains = <&disp_blk_ctrl IMX8MM_DISPBLK_PD_CSI_BRIDGE>;
+				status = "disabled";
+
+				port {
+					csi_in: endpoint {
+						remote-endpoint = <&imx8mm_mipi_csi_out>;
+					};
+				};
+			};
+
 			disp_blk_ctrl: blk-ctrl@32e28000 {
 				compatible = "fsl,imx8mm-disp-blk-ctrl", "syscon";
 				reg = <0x32e28000 0x100>;
@@ -1095,6 +1141,41 @@
 				#power-domain-cells = <1>;
 			};
 
+			mipi_csi: mipi-csi@32e30000 {
+				compatible = "fsl,imx8mm-mipi-csi2";
+				reg = <0x32e30000 0x1000>;
+				interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
+				assigned-clocks = <&clk IMX8MM_CLK_CSI1_CORE>,
+						  <&clk IMX8MM_CLK_CSI1_PHY_REF>;
+				assigned-clock-parents = <&clk IMX8MM_SYS_PLL2_1000M>,
+							  <&clk IMX8MM_SYS_PLL2_1000M>;
+				clock-frequency = <333000000>;
+				clocks = <&clk IMX8MM_CLK_DISP_APB_ROOT>,
+					 <&clk IMX8MM_CLK_CSI1_ROOT>,
+					 <&clk IMX8MM_CLK_CSI1_PHY_REF>,
+					 <&clk IMX8MM_CLK_DISP_AXI_ROOT>;
+				clock-names = "pclk", "wrap", "phy", "axi";
+				power-domains = <&disp_blk_ctrl IMX8MM_DISPBLK_PD_MIPI_CSI>;
+				status = "disabled";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+					};
+
+					port@1 {
+						reg = <1>;
+
+						imx8mm_mipi_csi_out: endpoint {
+							remote-endpoint = <&csi_in>;
+						};
+					};
+				};
+			};
+
 			usbotg1: usb@32e40000 {
 				compatible = "fsl,imx8mm-usb", "fsl,imx7d-usb";
 				reg = <0x32e40000 0x200>;
@@ -1105,7 +1186,7 @@
 				assigned-clock-parents = <&clk IMX8MM_SYS_PLL2_500M>;
 				phys = <&usbphynop1>;
 				fsl,usbmisc = <&usbmisc1 0>;
-				power-domains = <&pgc_otg1>;
+				power-domains = <&pgc_hsiomix>;
 				status = "disabled";
 			};
 
@@ -1125,7 +1206,7 @@
 				assigned-clock-parents = <&clk IMX8MM_SYS_PLL2_500M>;
 				phys = <&usbphynop2>;
 				fsl,usbmisc = <&usbmisc2 0>;
-				power-domains = <&pgc_otg2>;
+				power-domains = <&pgc_hsiomix>;
 				status = "disabled";
 			};
 
@@ -1135,6 +1216,19 @@
 				reg = <0x32e50200 0x200>;
 			};
 
+			pcie_phy: pcie-phy@32f00000 {
+				compatible = "fsl,imx8mm-pcie-phy";
+				reg = <0x32f00000 0x10000>;
+				clocks = <&clk IMX8MM_CLK_PCIE1_PHY>;
+				clock-names = "ref";
+				assigned-clocks = <&clk IMX8MM_CLK_PCIE1_PHY>;
+				assigned-clock-rates = <100000000>;
+				assigned-clock-parents = <&clk IMX8MM_SYS_PLL2_100M>;
+				resets = <&src IMX8MQ_RESET_PCIEPHY>;
+				reset-names = "pciephy";
+				#phy-cells = <0>;
+				status = "disabled";
+			};
 		};
 
 		dma_apbh: dma-controller@33000000 {
@@ -1166,6 +1260,37 @@
 			status = "disabled";
 		};
 
+		pcie0: pcie@33800000 {
+			compatible = "fsl,imx8mm-pcie";
+			reg = <0x33800000 0x400000>, <0x1ff00000 0x80000>;
+			reg-names = "dbi", "config";
+			#address-cells = <3>;
+			#size-cells = <2>;
+			device_type = "pci";
+			bus-range = <0x00 0xff>;
+			ranges =  <0x81000000 0 0x00000000 0x1ff80000 0 0x00010000 /* downstream I/O 64KB */
+				   0x82000000 0 0x18000000 0x18000000 0 0x07f00000>; /* non-prefetchable memory */
+			num-lanes = <1>;
+			num-viewport = <4>;
+			interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "msi";
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0x7>;
+			interrupt-map = <0 0 0 1 &gic GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>,
+					<0 0 0 2 &gic GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>,
+					<0 0 0 3 &gic GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
+					<0 0 0 4 &gic GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>;
+			fsl,max-link-speed = <2>;
+			linux,pci-domain = <0>;
+			power-domains = <&pgc_pcie>;
+			resets = <&src IMX8MQ_RESET_PCIE_CTRL_APPS_EN>,
+				 <&src IMX8MQ_RESET_PCIE_CTRL_APPS_TURNOFF>;
+			reset-names = "apps", "turnoff";
+			phys = <&pcie_phy>;
+			phy-names = "pcie-phy";
+			status = "disabled";
+		};
+
 		gpu_3d: gpu@38000000 {
 			compatible = "vivante,gc";
 			reg = <0x38000000 0x8000>;
@@ -1197,6 +1322,22 @@
 			power-domains = <&pgc_gpu>;
 		};
 
+		vpu_g1: video-codec@38300000 {
+			compatible = "nxp,imx8mm-vpu-g1";
+			reg = <0x38300000 0x10000>;
+			interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk IMX8MM_CLK_VPU_G1_ROOT>;
+			power-domains = <&vpu_blk_ctrl IMX8MM_VPUBLK_PD_G1>;
+		};
+
+		vpu_g2: video-codec@38310000 {
+			compatible = "nxp,imx8mq-vpu-g2";
+			reg = <0x38310000 0x10000>;
+			interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk IMX8MM_CLK_VPU_G2_ROOT>;
+			power-domains = <&vpu_blk_ctrl IMX8MM_VPUBLK_PD_G2>;
+		};
+
 		vpu_blk_ctrl: blk-ctrl@38330000 {
 			compatible = "fsl,imx8mm-vpu-blk-ctrl", "syscon";
 			reg = <0x38330000 0x100>;
@@ -1207,6 +1348,12 @@
 				 <&clk IMX8MM_CLK_VPU_G2_ROOT>,
 				 <&clk IMX8MM_CLK_VPU_H1_ROOT>;
 			clock-names = "g1", "g2", "h1";
+			assigned-clocks = <&clk IMX8MM_CLK_VPU_G1>,
+					  <&clk IMX8MM_CLK_VPU_G2>;
+			assigned-clock-parents = <&clk IMX8MM_VPU_PLL_OUT>,
+						 <&clk IMX8MM_VPU_PLL_OUT>;
+			assigned-clock-rates = <600000000>,
+					       <600000000>;
 			#power-domain-cells = <1>;
 		};
 
diff --git a/arch/arm64/boot/dts/freescale/imx8mn-beacon-baseboard.dtsi b/arch/arm64/boot/dts/freescale/imx8mn-beacon-baseboard.dtsi
index 376ca8ff7213..9e82069c941f 100644
--- a/arch/arm64/boot/dts/freescale/imx8mn-beacon-baseboard.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mn-beacon-baseboard.dtsi
@@ -126,7 +126,6 @@
 		compatible = "wlf,wm8962";
 		reg = <0x1a>;
 		clocks = <&clk IMX8MN_CLK_SAI3_ROOT>;
-		clock-names = "xclk";
 		DCVDD-supply = <&reg_audio>;
 		DBVDD-supply = <&reg_audio>;
 		AVDD-supply = <&reg_audio>;
@@ -147,7 +146,7 @@
 };
 
 &easrc {
-	fsl,asrc-rate  = <48000>;
+	fsl,asrc-rate = <48000>;
 	status = "okay";
 };
 
@@ -176,13 +175,14 @@
 	pinctrl-0 = <&pinctrl_uart3>;
 	assigned-clocks = <&clk IMX8MN_CLK_UART3>;
 	assigned-clock-parents = <&clk IMX8MN_SYS_PLL1_80M>;
+	uart-has-rtscts;
 	status = "okay";
 };
 
 &usbotg1 {
 	vbus-supply = <&reg_usb_otg_vbus>;
 	disable-over-current;
-	dr_mode="otg";
+	dr_mode = "otg";
 	status = "okay";
 };
 
@@ -259,6 +259,8 @@
 		fsl,pins = <
 			MX8MN_IOMUXC_ECSPI1_SCLK_UART3_DCE_RX	0x40
 			MX8MN_IOMUXC_ECSPI1_MOSI_UART3_DCE_TX	0x40
+			MX8MN_IOMUXC_ECSPI1_MISO_UART3_DCE_CTS_B	0x40
+			MX8MN_IOMUXC_ECSPI1_SS0_UART3_DCE_RTS_B	0x40
 		>;
 	};
 
diff --git a/arch/arm64/boot/dts/freescale/imx8mn-beacon-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mn-beacon-som.dtsi
index 3b2d627a0342..1133cded9be2 100644
--- a/arch/arm64/boot/dts/freescale/imx8mn-beacon-som.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mn-beacon-som.dtsi
@@ -274,7 +274,6 @@
 	bus-width = <4>;
 	non-removable;
 	cap-power-off-card;
-	pm-ignore-notify;
 	keep-power-in-suspend;
 	mmc-pwrseq = <&usdhc1_pwrseq>;
 	status = "okay";
diff --git a/arch/arm64/boot/dts/freescale/imx8mn-bsh-smm-s2-common.dtsi b/arch/arm64/boot/dts/freescale/imx8mn-bsh-smm-s2-common.dtsi
new file mode 100644
index 000000000000..c11895d9d582
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mn-bsh-smm-s2-common.dtsi
@@ -0,0 +1,426 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2021 Collabora Ltd.
+ * Copyright 2021 BSH Hausgeraete GmbH
+ */
+
+/dts-v1/;
+
+#include "imx8mn.dtsi"
+
+/ {
+	chosen {
+		stdout-path = &uart4;
+	};
+
+	fec_supply: fec-supply-en {
+		compatible = "regulator-fixed";
+		vin-supply = <&buck4_reg>;
+		regulator-name = "tja1101_en";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio2 20 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	usdhc2_pwrseq: usdhc2-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usdhc2_pwrseq>;
+		reset-gpios = <&gpio4 27 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&A53_0 {
+	cpu-supply = <&buck2_reg>;
+};
+
+&A53_1 {
+	cpu-supply = <&buck2_reg>;
+};
+
+&A53_2 {
+	cpu-supply = <&buck2_reg>;
+};
+
+&A53_3 {
+	cpu-supply = <&buck2_reg>;
+};
+
+&ecspi2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_espi2>;
+	status = "okay";
+};
+
+&fec1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_fec1>;
+	phy-mode = "rmii";
+	phy-handle = <&ethphy0>;
+	phy-supply = <&fec_supply>;
+	fsl,magic-packet;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy0: ethernet-phy@0 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <0>;
+			reset-gpios = <&gpio1 29 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <20>;
+			reset-deassert-us = <2000>;
+		};
+	};
+};
+
+&i2c1 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+
+	bd71847: pmic@4b {
+		compatible = "rohm,bd71847";
+		reg = <0x4b>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_pmic>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
+		rohm,reset-snvs-powered;
+
+		#clock-cells = <0>;
+		clocks = <&osc_32k 0>;
+		clock-output-names = "clk-32k-out";
+
+		regulators {
+			buck1_reg: BUCK1 {
+				/* PMIC_BUCK1 - VDD_SOC */
+				regulator-name = "buck1";
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <1300000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <1250>;
+			};
+
+			buck2_reg: BUCK2 {
+				/* PMIC_BUCK2 - VDD_ARM */
+				regulator-name = "buck2";
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <1300000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <1250>;
+			};
+
+			buck3_reg: BUCK3 {
+				/* PMIC_BUCK5 - VDD_DRAM_VPU_GPU */
+				regulator-name = "buck3";
+				regulator-min-microvolt = <700000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			buck4_reg: BUCK4 {
+				/* PMIC_BUCK6 - VDD_3V3 */
+				regulator-name = "buck4";
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			buck5_reg: BUCK5 {
+				/* PMIC_BUCK7 - VDD_1V8 */
+				regulator-name = "buck5";
+				regulator-min-microvolt = <1605000>;
+				regulator-max-microvolt = <1995000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			buck6_reg: BUCK6 {
+				/* PMIC_BUCK8 - NVCC_DRAM */
+				regulator-name = "buck6";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1400000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo1_reg: LDO1 {
+				/* PMIC_LDO1 - NVCC_SNVS_1V8 */
+				regulator-name = "ldo1";
+				regulator-min-microvolt = <1600000>;
+				regulator-max-microvolt = <1900000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo2_reg: LDO2 {
+				/* PMIC_LDO2 - VDD_SNVS_0V8 */
+				regulator-name = "ldo2";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <900000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo3_reg: LDO3 {
+				/* PMIC_LDO3 - VDDA_1V8 */
+				regulator-name = "ldo3";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo4_reg: LDO4 {
+				/* PMIC_LDO4 - VDD_MIPI_0V9 */
+				regulator-name = "ldo4";
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo6_reg: LDO6 {
+				/* PMIC_LDO6 - VDD_MIPI_1V2 */
+				regulator-name = "ldo6";
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+		};
+	};
+};
+
+&i2c3 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "okay";
+};
+
+&i2c4 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c4>;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	assigned-clocks = <&clk IMX8MN_CLK_UART3>;
+	assigned-clock-parents = <&clk IMX8MN_SYS_PLL1_80M>;
+	uart-has-rtscts;
+	status = "okay";
+
+	bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_bluetooth>;
+		shutdown-gpios = <&gpio1 15 GPIO_ACTIVE_HIGH>;
+		device-wakeup-gpios = <&gpio1 18 GPIO_ACTIVE_HIGH>;
+		host-wakeup-gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>;
+		max-speed = <3000000>;
+	};
+};
+
+/* Console */
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+	status = "okay";
+};
+
+&usbotg1 {
+	dr_mode = "peripheral";
+	disable-over-current;
+	status = "okay";
+};
+
+&usdhc2 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
+	mmc-pwrseq = <&usdhc2_pwrseq>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+
+	brcmf: bcrmf@1 {
+		compatible = "brcm,bcm4329-fmac";
+		reg = <1>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_wlan>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "host-wake";
+	};
+};
+
+&wdog1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog>;
+	fsl,ext-reset-output;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_bluetooth: bluetoothgrp {
+		fsl,pins = <
+			MX8MN_IOMUXC_GPIO1_IO15_GPIO1_IO15		0x044	/* BT_REG_ON */
+			MX8MN_IOMUXC_ENET_TD3_GPIO1_IO18		0x046	/* BT_DEV_WAKE */
+			MX8MN_IOMUXC_ENET_RD2_GPIO1_IO28		0x090	/* BT_HOST_WAKE */
+		>;
+	};
+
+	pinctrl_espi2: espi2grp {
+		fsl,pins = <
+			MX8MN_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK		0x082
+			MX8MN_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI		0x082
+			MX8MN_IOMUXC_ECSPI2_MISO_ECSPI2_MISO		0x082
+			MX8MN_IOMUXC_ECSPI2_SS0_ECSPI2_SS0		0x040
+		>;
+	};
+
+	pinctrl_fec1: fec1grp {
+		fsl,pins = <
+			MX8MN_IOMUXC_ENET_MDC_ENET1_MDC			0x002
+			MX8MN_IOMUXC_ENET_MDIO_ENET1_MDIO		0x002
+			MX8MN_IOMUXC_ENET_RD0_ENET1_RGMII_RD0		0x090
+			MX8MN_IOMUXC_ENET_RD1_ENET1_RGMII_RD1		0x090
+			MX8MN_IOMUXC_ENET_RXC_ENET1_RX_ER		0x090
+			MX8MN_IOMUXC_ENET_TD0_ENET1_RGMII_TD0		0x016
+			MX8MN_IOMUXC_ENET_TD1_ENET1_RGMII_TD1		0x016
+			MX8MN_IOMUXC_ENET_TD2_ENET1_TX_CLK		0x016
+			MX8MN_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL	0x016
+			MX8MN_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL	0x090
+			MX8MN_IOMUXC_ENET_TXC_ENET1_TX_ER		0x016
+			MX8MN_IOMUXC_SD2_CD_B_GPIO2_IO12		0x150	/* RMII_INT - ENET_INT */
+			MX8MN_IOMUXC_SD2_WP_GPIO2_IO20			0x150	/* RMII_EN - ENET_EN */
+			MX8MN_IOMUXC_SD2_RESET_B_GPIO2_IO19		0x016	/* RMII_WAKE - GPIO_ENET_WAKE */
+			MX8MN_IOMUXC_ENET_RD3_GPIO1_IO29		0x016	/* RMII_RESET - GPIO_ENET_RST */
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX8MN_IOMUXC_I2C1_SCL_I2C1_SCL			0x400000c2
+			MX8MN_IOMUXC_I2C1_SDA_I2C1_SDA			0x400000c2
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX8MN_IOMUXC_I2C3_SCL_I2C3_SCL			0x400000c2
+			MX8MN_IOMUXC_I2C3_SDA_I2C3_SDA			0x400000c2
+		>;
+	};
+
+	pinctrl_i2c4: i2c4grp {
+		fsl,pins = <
+			MX8MN_IOMUXC_I2C4_SCL_I2C4_SCL			0x400000c2
+			MX8MN_IOMUXC_I2C4_SDA_I2C4_SDA			0x400000c2
+		>;
+	};
+
+	pinctrl_pmic: pmicirq {
+		fsl,pins = <
+			MX8MN_IOMUXC_GPIO1_IO03_GPIO1_IO3		0x040
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX8MN_IOMUXC_UART2_RXD_UART2_DCE_RX		0x040
+			MX8MN_IOMUXC_UART2_TXD_UART2_DCE_TX		0x040
+		>;
+	};
+
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <
+			MX8MN_IOMUXC_UART3_TXD_UART3_DCE_TX		0x040
+			MX8MN_IOMUXC_UART3_RXD_UART3_DCE_RX		0x040
+			MX8MN_IOMUXC_ECSPI1_MISO_UART3_DCE_CTS_B	0x040
+			MX8MN_IOMUXC_ECSPI1_SS0_UART3_DCE_RTS_B		0x040
+		>;
+	};
+
+	pinctrl_uart4: uart4grp {
+		fsl,pins = <
+			MX8MN_IOMUXC_UART4_RXD_UART4_DCE_RX		0x040
+			MX8MN_IOMUXC_UART4_TXD_UART4_DCE_TX		0x040
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX8MN_IOMUXC_SD2_CLK_USDHC2_CLK			0x090
+			MX8MN_IOMUXC_SD2_CMD_USDHC2_CMD			0x0d0
+			MX8MN_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x0d0
+			MX8MN_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x0d0
+			MX8MN_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x0d0
+			MX8MN_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x0d0
+		>;
+	};
+
+	pinctrl_usdhc2_100mhz: usdhc2grp100mhz {
+		fsl,pins = <
+			MX8MN_IOMUXC_SD2_CLK_USDHC2_CLK			0x094
+			MX8MN_IOMUXC_SD2_CMD_USDHC2_CMD			0x0d4
+			MX8MN_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x0d4
+			MX8MN_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x0d4
+			MX8MN_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x0d4
+			MX8MN_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x0d4
+		>;
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2grp200mhz {
+		fsl,pins = <
+			MX8MN_IOMUXC_SD2_CLK_USDHC2_CLK			0x096
+			MX8MN_IOMUXC_SD2_CMD_USDHC2_CMD			0x0d6
+			MX8MN_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x0d6
+			MX8MN_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x0d6
+			MX8MN_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x0d6
+			MX8MN_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x0d6
+		>;
+	};
+
+	pinctrl_usdhc2_pwrseq: usdhc2pwrseqgrp {
+		fsl,pins = <
+			MX8MN_IOMUXC_SAI2_MCLK_GPIO4_IO27		0x040	/* WL_REG_ON */
+		>;
+	};
+
+	pinctrl_wdog: wdoggrp {
+		fsl,pins = <
+			MX8MN_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B		0x046
+		>;
+	};
+
+	pinctrl_wlan: wlangrp {
+		fsl,pins = <
+			MX8MN_IOMUXC_GPIO1_IO00_GPIO1_IO0		0x0d6	/* GPIO_0 - WIFI_GPIO_0 */
+			MX8MN_IOMUXC_GPIO1_IO08_GPIO1_IO8		0x0d6	/* GPIO_1 - WIFI_GPIO_1 */
+			MX8MN_IOMUXC_GPIO1_IO04_GPIO1_IO4		0x0d6	/* BT_GPIO_5 - WIFI_GPIO_5 */
+			MX8MN_IOMUXC_SPDIF_RX_GPIO5_IO4			0x0d6	/* I2S_CLK - WIFI_GPIO_6 */
+		>;
+	};
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mn-bsh-smm-s2.dts b/arch/arm64/boot/dts/freescale/imx8mn-bsh-smm-s2.dts
new file mode 100644
index 000000000000..33f98582eace
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mn-bsh-smm-s2.dts
@@ -0,0 +1,48 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2021 Collabora Ltd.
+ * Copyright 2021 BSH Hausgeraete GmbH
+ */
+
+/dts-v1/;
+
+#include "imx8mn-bsh-smm-s2-common.dtsi"
+
+/ {
+	model = "BSH SMM S2";
+	compatible = "bsh,imx8mn-bsh-smm-s2", "fsl,imx8mn";
+
+	memory@40000000 {
+		device_type = "memory";
+		reg = <0x0 0x40000000 0x0 0x10000000>;
+	};
+};
+
+&gpmi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpmi_nand>;
+	nand-on-flash-bbt;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_gpmi_nand: gpmi-nand {
+		fsl,pins = <
+			MX8MN_IOMUXC_NAND_ALE_RAWNAND_ALE		0x00000096
+			MX8MN_IOMUXC_NAND_CE0_B_RAWNAND_CE0_B		0x00000096
+			MX8MN_IOMUXC_NAND_CLE_RAWNAND_CLE		0x00000096
+			MX8MN_IOMUXC_NAND_DATA00_RAWNAND_DATA00		0x00000096
+			MX8MN_IOMUXC_NAND_DATA01_RAWNAND_DATA01		0x00000096
+			MX8MN_IOMUXC_NAND_DATA02_RAWNAND_DATA02		0x00000096
+			MX8MN_IOMUXC_NAND_DATA03_RAWNAND_DATA03		0x00000096
+			MX8MN_IOMUXC_NAND_DATA04_RAWNAND_DATA04		0x00000096
+			MX8MN_IOMUXC_NAND_DATA05_RAWNAND_DATA05		0x00000096
+			MX8MN_IOMUXC_NAND_DATA06_RAWNAND_DATA06		0x00000096
+			MX8MN_IOMUXC_NAND_DATA07_RAWNAND_DATA07		0x00000096
+			MX8MN_IOMUXC_NAND_RE_B_RAWNAND_RE_B		0x00000096
+			MX8MN_IOMUXC_NAND_READY_B_RAWNAND_READY_B	0x00000056
+			MX8MN_IOMUXC_NAND_WE_B_RAWNAND_WE_B		0x00000096
+			MX8MN_IOMUXC_NAND_WP_B_RAWNAND_WP_B		0x00000096
+		>;
+	};
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mn-bsh-smm-s2pro.dts b/arch/arm64/boot/dts/freescale/imx8mn-bsh-smm-s2pro.dts
new file mode 100644
index 000000000000..fbbb3367037b
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mn-bsh-smm-s2pro.dts
@@ -0,0 +1,170 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright 2021 Collabora Ltd.
+ * Copyright 2021 BSH Hausgeraete GmbH
+ */
+
+/dts-v1/;
+
+#include "imx8mn-bsh-smm-s2-common.dtsi"
+#include <dt-bindings/sound/tlv320aic31xx.h>
+
+/ {
+	model = "BSH SMM S2 PRO";
+	compatible = "bsh,imx8mn-bsh-smm-s2pro", "fsl,imx8mn";
+
+	memory@40000000 {
+		device_type = "memory";
+		reg = <0x0 0x40000000 0x0 0x20000000>;
+	};
+
+	sound-tlv320aic31xx {
+		compatible = "fsl,imx-audio-tlv320aic31xx";
+		model = "tlv320aic31xx-hifi";
+		audio-cpu = <&sai3>;
+		audio-codec = <&tlv320dac3101>;
+		audio-asrc = <&easrc>;
+		audio-routing =
+			"Ext Spk", "SPL",
+			"Ext Spk", "SPR";
+		mclk-id = <PLL_CLKIN_BCLK>;
+	};
+
+	vdd_input: vdd_input {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_input";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+};
+
+&easrc {
+	fsl,asrc-rate = <48000>;
+	fsl,asrc-format = <10>;
+	status = "okay";
+};
+
+&i2c2 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	status = "okay";
+
+	tlv320dac3101: audio-codec@18 {
+		compatible = "ti,tlv320dac3101";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_dac_rst>;
+		reg = <0x18>;
+		#sound-dai-cells = <0>;
+		HPVDD-supply = <&buck4_reg>;
+		SPRVDD-supply = <&vdd_input>;
+		SPLVDD-supply = <&vdd_input>;
+		AVDD-supply = <&buck4_reg>;
+		IOVDD-supply = <&buck4_reg>;
+		DVDD-supply = <&buck5_reg>;
+		reset-gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
+		ai31xx-micbias-vg = <MICBIAS_AVDDV>;
+		clocks = <&clk IMX8MN_CLK_SAI3_ROOT>;
+	};
+};
+
+&sai3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sai3>;
+	assigned-clocks = <&clk IMX8MN_CLK_SAI3>;
+	assigned-clock-parents = <&clk IMX8MN_AUDIO_PLL1_OUT>;
+	assigned-clock-rates = <24576000>;
+	fsl,sai-mclk-direction-output;
+	status = "okay";
+};
+
+/* eMMC */
+&usdhc1 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
+	bus-width = <8>;
+	non-removable;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_dac_rst: dacrstgrp {
+		fsl,pins = <
+			MX8MN_IOMUXC_GPIO1_IO06_GPIO1_IO6		0x19 /* DAC_RST */
+		>;
+	};
+
+	pinctrl_espi2: espi2grp {
+		fsl,pins = <
+			MX8MN_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK		0x082
+			MX8MN_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI		0x082
+			MX8MN_IOMUXC_ECSPI2_MISO_ECSPI2_MISO		0x082
+			MX8MN_IOMUXC_ECSPI2_SS0_ECSPI2_SS0		0x040
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX8MN_IOMUXC_I2C2_SCL_I2C2_SCL			0x400000c3
+			MX8MN_IOMUXC_I2C2_SDA_I2C2_SDA			0x400000c3
+		>;
+	};
+
+	pinctrl_sai3: sai3grp {
+		fsl,pins = <
+			MX8MN_IOMUXC_SAI3_TXFS_SAI3_TX_SYNC		0xd6
+			MX8MN_IOMUXC_SAI3_TXC_SAI3_TX_BCLK		0xd6
+			MX8MN_IOMUXC_SAI3_TXD_SAI3_TX_DATA0		0xd6
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX8MN_IOMUXC_SD1_CLK_USDHC1_CLK			0x40000090
+			MX8MN_IOMUXC_SD1_CMD_USDHC1_CMD			0x0d0
+			MX8MN_IOMUXC_SD1_DATA0_USDHC1_DATA0		0x0d0
+			MX8MN_IOMUXC_SD1_DATA1_USDHC1_DATA1		0x0d0
+			MX8MN_IOMUXC_SD1_DATA2_USDHC1_DATA2		0x0d0
+			MX8MN_IOMUXC_SD1_DATA3_USDHC1_DATA3		0x0d0
+			MX8MN_IOMUXC_SD1_DATA4_USDHC1_DATA4		0x0d0
+			MX8MN_IOMUXC_SD1_DATA5_USDHC1_DATA5		0x0d0
+			MX8MN_IOMUXC_SD1_DATA6_USDHC1_DATA6		0x0d0
+			MX8MN_IOMUXC_SD1_DATA7_USDHC1_DATA7		0x0d0
+			MX8MN_IOMUXC_SD1_STROBE_USDHC1_STROBE		0x090
+		>;
+	};
+
+	pinctrl_usdhc1_100mhz: usdhc1grp100mhz {
+		fsl,pins = <
+			MX8MN_IOMUXC_SD1_CLK_USDHC1_CLK			0x40000094
+			MX8MN_IOMUXC_SD1_CMD_USDHC1_CMD			0x0d4
+			MX8MN_IOMUXC_SD1_DATA0_USDHC1_DATA0		0x0d4
+			MX8MN_IOMUXC_SD1_DATA1_USDHC1_DATA1		0x0d4
+			MX8MN_IOMUXC_SD1_DATA2_USDHC1_DATA2		0x0d4
+			MX8MN_IOMUXC_SD1_DATA3_USDHC1_DATA3		0x0d4
+			MX8MN_IOMUXC_SD1_DATA4_USDHC1_DATA4		0x0d4
+			MX8MN_IOMUXC_SD1_DATA5_USDHC1_DATA5		0x0d4
+			MX8MN_IOMUXC_SD1_DATA6_USDHC1_DATA6		0x0d4
+			MX8MN_IOMUXC_SD1_DATA7_USDHC1_DATA7		0x0d4
+			MX8MN_IOMUXC_SD1_STROBE_USDHC1_STROBE		0x094
+		>;
+	};
+
+	pinctrl_usdhc1_200mhz: usdhc1grp200mhz {
+		fsl,pins = <
+			MX8MN_IOMUXC_SD1_CLK_USDHC1_CLK			0x40000096
+			MX8MN_IOMUXC_SD1_CMD_USDHC1_CMD			0x0d6
+			MX8MN_IOMUXC_SD1_DATA0_USDHC1_DATA0		0x0d6
+			MX8MN_IOMUXC_SD1_DATA1_USDHC1_DATA1		0x0d6
+			MX8MN_IOMUXC_SD1_DATA2_USDHC1_DATA2		0x0d6
+			MX8MN_IOMUXC_SD1_DATA3_USDHC1_DATA3		0x0d6
+			MX8MN_IOMUXC_SD1_DATA4_USDHC1_DATA4		0x0d6
+			MX8MN_IOMUXC_SD1_DATA5_USDHC1_DATA5		0x0d6
+			MX8MN_IOMUXC_SD1_DATA6_USDHC1_DATA6		0x0d6
+			MX8MN_IOMUXC_SD1_DATA7_USDHC1_DATA7		0x0d6
+			MX8MN_IOMUXC_SD1_STROBE_USDHC1_STROBE		0x096
+		>;
+	};
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mn-ddr3l-evk.dts b/arch/arm64/boot/dts/freescale/imx8mn-ddr3l-evk.dts
new file mode 100644
index 000000000000..000e2c0596df
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mn-ddr3l-evk.dts
@@ -0,0 +1,114 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+/dts-v1/;
+
+#include "imx8mn.dtsi"
+#include "imx8mn-evk.dtsi"
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	model = "NXP i.MX8MNano DDR3L EVK board";
+	compatible = "fsl,imx8mn-ddr3l-evk", "fsl,imx8mn";
+};
+
+&A53_0 {
+	cpu-supply = <&buck1>;
+};
+
+&A53_1 {
+	cpu-supply = <&buck1>;
+};
+
+&A53_2 {
+	cpu-supply = <&buck1>;
+};
+
+&A53_3 {
+	cpu-supply = <&buck1>;
+};
+
+&i2c1 {
+	pmic: pmic@25 {
+		compatible = "nxp,pca9450b";
+		reg = <0x25>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_pmic>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
+
+		regulators {
+			buck1: BUCK1 {
+				regulator-name = "VDD_SOC_0V9";
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <950000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <3125>;
+			};
+
+			buck4: BUCK4 {
+				regulator-name = "VDD_3V3";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			buck5: BUCK5 {
+				regulator-name = "VDD_1V8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			buck6: BUCK6 {
+				regulator-name = "NVCC_DRAM_1V35";
+				regulator-min-microvolt = <1350000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo1: LDO1 {
+				regulator-name = "NVCC_SNVS_1V8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo2: LDO2 {
+				regulator-name = "VDD_SNVS_0V8";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo3: LDO3 {
+				regulator-name = "VDDA_1V8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo4: LDO4 {
+				regulator-name = "VDD_PHY_1V2";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo5: LDO5 {
+				regulator-name = "NVCC_SD2";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+		};
+	};
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dts b/arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dts
index 7dfee715a2c4..d8ce217c6016 100644
--- a/arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dts
@@ -59,6 +59,10 @@
 		interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
 		rohm,reset-snvs-powered;
 
+		#clock-cells = <0>;
+		clocks = <&osc_32k 0>;
+		clock-output-names = "clk-32k-out";
+
 		regulators {
 			buck1_reg: BUCK1 {
 				regulator-name = "buck1";
diff --git a/arch/arm64/boot/dts/freescale/imx8mn-evk.dts b/arch/arm64/boot/dts/freescale/imx8mn-evk.dts
index b4225cfcb6d9..4eb467df5ba7 100644
--- a/arch/arm64/boot/dts/freescale/imx8mn-evk.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mn-evk.dts
@@ -41,18 +41,18 @@
 
 		regulators {
 			buck1: BUCK1{
-				regulator-name = "BUCK1";
-				regulator-min-microvolt = <600000>;
-				regulator-max-microvolt = <2187500>;
+				regulator-name = "VDD_SOC";
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <950000>;
 				regulator-boot-on;
 				regulator-always-on;
 				regulator-ramp-delay = <3125>;
 			};
 
 			buck2: BUCK2 {
-				regulator-name = "BUCK2";
-				regulator-min-microvolt = <600000>;
-				regulator-max-microvolt = <2187500>;
+				regulator-name = "VDD_ARM_0V9";
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <1000000>;
 				regulator-boot-on;
 				regulator-always-on;
 				regulator-ramp-delay = <3125>;
@@ -61,63 +61,63 @@
 			};
 
 			buck4: BUCK4{
-				regulator-name = "BUCK4";
-				regulator-min-microvolt = <600000>;
-				regulator-max-microvolt = <3400000>;
+				regulator-name = "VDD_3V3";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
 				regulator-boot-on;
 				regulator-always-on;
 			};
 
 			buck5: BUCK5{
-				regulator-name = "BUCK5";
-				regulator-min-microvolt = <600000>;
-				regulator-max-microvolt = <3400000>;
+				regulator-name = "VDD_1V8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
 				regulator-boot-on;
 				regulator-always-on;
 			};
 
 			buck6: BUCK6 {
-				regulator-name = "BUCK6";
-				regulator-min-microvolt = <600000>;
-				regulator-max-microvolt = <3400000>;
+				regulator-name = "NVCC_DRAM_1V1";
+				regulator-min-microvolt = <1100000>;
+				regulator-max-microvolt = <1100000>;
 				regulator-boot-on;
 				regulator-always-on;
 			};
 
 			ldo1: LDO1 {
-				regulator-name = "LDO1";
-				regulator-min-microvolt = <1600000>;
-				regulator-max-microvolt = <3300000>;
+				regulator-name = "NVCC_SNVS_1V8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
 				regulator-boot-on;
 				regulator-always-on;
 			};
 
 			ldo2: LDO2 {
-				regulator-name = "LDO2";
+				regulator-name = "VDD_SNVS_0V8";
 				regulator-min-microvolt = <800000>;
-				regulator-max-microvolt = <1150000>;
+				regulator-max-microvolt = <800000>;
 				regulator-boot-on;
 				regulator-always-on;
 			};
 
 			ldo3: LDO3 {
-				regulator-name = "LDO3";
-				regulator-min-microvolt = <800000>;
-				regulator-max-microvolt = <3300000>;
+				regulator-name = "VDDA_1V8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
 				regulator-boot-on;
 				regulator-always-on;
 			};
 
 			ldo4: LDO4 {
-				regulator-name = "LDO4";
-				regulator-min-microvolt = <800000>;
-				regulator-max-microvolt = <3300000>;
+				regulator-name = "VDD_PHY_1V2";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
 				regulator-boot-on;
 				regulator-always-on;
 			};
 
 			ldo5: LDO5 {
-				regulator-name = "LDO5";
+				regulator-name = "NVCC_SD2";
 				regulator-min-microvolt = <1800000>;
 				regulator-max-microvolt = <3300000>;
 				regulator-boot-on;
diff --git a/arch/arm64/boot/dts/freescale/imx8mn-evk.dtsi b/arch/arm64/boot/dts/freescale/imx8mn-evk.dtsi
index 85e65f8719ea..261c36540079 100644
--- a/arch/arm64/boot/dts/freescale/imx8mn-evk.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mn-evk.dtsi
@@ -47,6 +47,11 @@
 		linux,autosuspend-period = <125>;
 	};
 
+	audio_codec_bt_sco: audio-codec-bt-sco {
+		compatible = "linux,bt-sco";
+		#sound-dai-cells = <1>;
+	};
+
 	wm8524: audio-codec {
 		#sound-dai-cells = <0>;
 		compatible = "wlf,wm8524";
@@ -57,6 +62,25 @@
 		clock-names = "mclk";
 	};
 
+	sound-bt-sco {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "bt-sco-audio";
+		simple-audio-card,format = "dsp_a";
+		simple-audio-card,bitclock-inversion;
+		simple-audio-card,frame-master = <&btcpu>;
+		simple-audio-card,bitclock-master = <&btcpu>;
+
+		btcpu: simple-audio-card,cpu {
+			sound-dai = <&sai2>;
+			dai-tdm-slot-num = <2>;
+			dai-tdm-slot-width = <16>;
+		};
+
+		simple-audio-card,codec {
+			sound-dai = <&audio_codec_bt_sco 1>;
+		};
+	};
+
 	sound-wm8524 {
 		compatible = "fsl,imx-audio-wm8524";
 		model = "wm8524-audio";
@@ -78,7 +102,7 @@
 };
 
 &easrc {
-	fsl,asrc-rate  = <48000>;
+	fsl,asrc-rate = <48000>;
 	status = "okay";
 };
 
@@ -97,10 +121,35 @@
 		ethphy0: ethernet-phy@0 {
 			compatible = "ethernet-phy-ieee802.3-c22";
 			reg = <0>;
+			reset-gpios = <&gpio4 22 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <10000>;
+			qca,disable-smarteee;
+			vddio-supply = <&vddio>;
+
+			vddio: vddio-regulator {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
 		};
 	};
 };
 
+&flexspi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexspi>;
+	status = "okay";
+
+	flash0: flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		spi-max-frequency = <166000000>;
+		spi-tx-bus-width = <4>;
+		spi-rx-bus-width = <4>;
+	};
+};
+
 &i2c1 {
 	clock-frequency = <400000>;
 	pinctrl-names = "default";
@@ -158,6 +207,16 @@
 	};
 };
 
+&sai2 {
+	#sound-dai-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sai2>;
+	assigned-clocks = <&clk IMX8MN_CLK_SAI2>;
+	assigned-clock-parents = <&clk IMX8MN_AUDIO_PLL1_OUT>;
+	assigned-clock-rates = <24576000>;
+	status = "okay";
+};
+
 &sai3 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_sai3>;
@@ -187,6 +246,15 @@
 	status = "okay";
 };
 
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	assigned-clocks = <&clk IMX8MN_CLK_UART3>;
+	assigned-clock-parents = <&clk IMX8MN_SYS_PLL1_80M>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
 &usbotg1 {
 	dr_mode = "otg";
 	hnp-disable;
@@ -258,6 +326,17 @@
 		>;
 	};
 
+	pinctrl_flexspi: flexspigrp {
+		fsl,pins = <
+			MX8MN_IOMUXC_NAND_ALE_QSPI_A_SCLK               0x1c2
+			MX8MN_IOMUXC_NAND_CE0_B_QSPI_A_SS0_B            0x82
+			MX8MN_IOMUXC_NAND_DATA00_QSPI_A_DATA0           0x82
+			MX8MN_IOMUXC_NAND_DATA01_QSPI_A_DATA1           0x82
+			MX8MN_IOMUXC_NAND_DATA02_QSPI_A_DATA2           0x82
+			MX8MN_IOMUXC_NAND_DATA03_QSPI_A_DATA3           0x82
+		>;
+	};
+
 	pinctrl_gpio_led: gpioledgrp {
 		fsl,pins = <
 			MX8MN_IOMUXC_NAND_READY_B_GPIO3_IO16	0x19
@@ -309,6 +388,15 @@
 		>;
 	};
 
+	pinctrl_sai2: sai2grp {
+		fsl,pins = <
+			MX8MN_IOMUXC_SAI2_TXC_SAI2_TX_BCLK      0xd6
+			MX8MN_IOMUXC_SAI2_TXFS_SAI2_TX_SYNC     0xd6
+			MX8MN_IOMUXC_SAI2_TXD0_SAI2_TX_DATA0    0xd6
+			MX8MN_IOMUXC_SAI2_RXD0_SAI2_RX_DATA0    0xd6
+		>;
+	};
+
 	pinctrl_sai3: sai3grp {
 		fsl,pins = <
 			MX8MN_IOMUXC_SAI3_TXFS_SAI3_TX_SYNC     0xd6
@@ -338,6 +426,15 @@
 		>;
 	};
 
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <
+			MX8MN_IOMUXC_ECSPI1_SCLK_UART3_DCE_RX		0x140
+			MX8MN_IOMUXC_ECSPI1_MOSI_UART3_DCE_TX		0x140
+			MX8MN_IOMUXC_ECSPI1_SS0_UART3_DCE_RTS_B	0x140
+			MX8MN_IOMUXC_ECSPI1_MISO_UART3_DCE_CTS_B	0x140
+		>;
+	};
+
 	pinctrl_usdhc2_gpio: usdhc2gpiogrp {
 		fsl,pins = <
 			MX8MN_IOMUXC_GPIO1_IO15_GPIO1_IO15	0x1c4
diff --git a/arch/arm64/boot/dts/freescale/imx8mn-tqma8mqnl-mba8mx.dts b/arch/arm64/boot/dts/freescale/imx8mn-tqma8mqnl-mba8mx.dts
new file mode 100644
index 000000000000..3f1e49bfe38f
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mn-tqma8mqnl-mba8mx.dts
@@ -0,0 +1,237 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2020-2021 TQ-Systems GmbH
+ */
+
+/dts-v1/;
+
+#include "imx8mn-tqma8mqnl.dtsi"
+#include "mba8mx.dtsi"
+
+/ {
+	model = "TQ-Systems GmbH i.MX8MN TQMa8MxNL on MBa8Mx";
+	compatible = "tq,imx8mn-tqma8mqnl-mba8mx", "tq,imx8mn-tqma8mqnl", "fsl,imx8mn";
+
+	aliases {
+		eeprom0 = &eeprom3;
+		mmc0 = &usdhc3;
+		mmc1 = &usdhc2;
+		mmc2 = &usdhc1;
+		rtc0 = &pcf85063;
+		rtc1 = &snvs_rtc;
+	};
+
+	reg_usdhc2_vmmc: regulator-vmmc {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>;
+		regulator-name = "VSD_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		startup-delay-us = <100>;
+		off-on-delay-us = <12000>;
+	};
+};
+
+/* Located on TQMa8MxML-ADAP */
+&gpio2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb0hub_sel>;
+
+	sel-usb-hub-hog {
+		gpio-hog;
+		gpios = <1 GPIO_ACTIVE_HIGH>;
+		output-high;
+	};
+};
+
+&i2c1 {
+	expander2: gpio@27 {
+		compatible = "nxp,pca9555";
+		reg = <0x27>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		vcc-supply = <&reg_vcc_3v3>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_expander2>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <9 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+};
+
+&sai3 {
+	assigned-clocks = <&clk IMX8MN_CLK_SAI3>;
+	assigned-clock-parents = <&clk IMX8MN_AUDIO_PLL1_OUT>;
+	clock-names = "bus", "mclk0", "mclk1", "mclk2", "mclk3", "pll8k", "pll11k";
+	clocks = <&clk IMX8MN_CLK_SAI3_IPG>, <&clk IMX8MN_CLK_DUMMY>,
+		 <&clk IMX8MN_CLK_SAI3_ROOT>, <&clk IMX8MN_CLK_DUMMY>,
+		 <&clk IMX8MN_CLK_DUMMY>, <&clk IMX8MN_AUDIO_PLL1_OUT>,
+		 <&clk IMX8MN_AUDIO_PLL2_OUT>;
+};
+
+&tlv320aic3x04 {
+	clock-names = "mclk";
+	clocks = <&clk IMX8MN_CLK_SAI3_ROOT>;
+};
+
+&usbotg1 {
+	dr_mode = "host";
+	disable-over-current;
+	power-active-high;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_ecspi1: ecspi1grp {
+		fsl,pins = <MX8MN_IOMUXC_ECSPI1_SCLK_ECSPI1_SCLK	0x00000146>,
+			   <MX8MN_IOMUXC_ECSPI1_MOSI_ECSPI1_MOSI	0x00000146>,
+			   <MX8MN_IOMUXC_ECSPI1_MISO_ECSPI1_MISO	0x00000146>,
+			   <MX8MN_IOMUXC_ECSPI1_SS0_GPIO5_IO9		0x00000146>;
+	};
+
+	pinctrl_ecspi2: ecspi2grp {
+		fsl,pins = <MX8MN_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK	0x00000146>,
+			   <MX8MN_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI	0x00000146>,
+			   <MX8MN_IOMUXC_ECSPI2_MISO_ECSPI2_MISO	0x00000146>,
+			   <MX8MN_IOMUXC_ECSPI2_SS0_GPIO5_IO13		0x00000146>;
+	};
+
+	pinctrl_expander2: expander2grp {
+		fsl,pins = <MX8MN_IOMUXC_GPIO1_IO09_GPIO1_IO9		0x94>;
+	};
+
+	pinctrl_fec1: fec1grp {
+		fsl,pins = <MX8MN_IOMUXC_ENET_MDC_ENET1_MDC		0x40000002>,
+			   <MX8MN_IOMUXC_ENET_MDIO_ENET1_MDIO		0x40000002>,
+			   <MX8MN_IOMUXC_ENET_TD3_ENET1_RGMII_TD3	0x14>,
+			   <MX8MN_IOMUXC_ENET_TD2_ENET1_RGMII_TD2	0x14>,
+			   <MX8MN_IOMUXC_ENET_TD1_ENET1_RGMII_TD1	0x14>,
+			   <MX8MN_IOMUXC_ENET_TD0_ENET1_RGMII_TD0	0x14>,
+			   <MX8MN_IOMUXC_ENET_RD3_ENET1_RGMII_RD3	0x90>,
+			   <MX8MN_IOMUXC_ENET_RD2_ENET1_RGMII_RD2	0x90>,
+			   <MX8MN_IOMUXC_ENET_RD1_ENET1_RGMII_RD1	0x90>,
+			   <MX8MN_IOMUXC_ENET_RD0_ENET1_RGMII_RD0	0x90>,
+			   <MX8MN_IOMUXC_ENET_TXC_ENET1_RGMII_TXC	0x14>,
+			   <MX8MN_IOMUXC_ENET_RXC_ENET1_RGMII_RXC	0x90>,
+			   <MX8MN_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL	0x90>,
+			   <MX8MN_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL	0x14>;
+	};
+
+	pinctrl_gpiobutton: gpiobuttongrp {
+		fsl,pins = <MX8MN_IOMUXC_GPIO1_IO05_GPIO1_IO5		0x84>,
+			   <MX8MN_IOMUXC_GPIO1_IO07_GPIO1_IO7		0x84>,
+			   <MX8MN_IOMUXC_SD1_CLK_GPIO2_IO0		0x84>;
+	};
+
+	pinctrl_gpioled: gpioledgrp {
+		fsl,pins = <MX8MN_IOMUXC_GPIO1_IO00_GPIO1_IO0		0x84>,
+			   <MX8MN_IOMUXC_NAND_DQS_GPIO3_IO14		0x84>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <MX8MN_IOMUXC_I2C2_SCL_I2C2_SCL		0x400001C4>,
+			   <MX8MN_IOMUXC_I2C2_SDA_I2C2_SDA		0x400001C4>;
+	};
+
+	pinctrl_i2c2_gpio: i2c2gpiogrp {
+		fsl,pins = <MX8MN_IOMUXC_I2C2_SCL_GPIO5_IO16		0x400001C4>,
+			   <MX8MN_IOMUXC_I2C2_SDA_GPIO5_IO17		0x400001C4>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <MX8MN_IOMUXC_I2C3_SCL_I2C3_SCL		0x400001C4>,
+			   <MX8MN_IOMUXC_I2C3_SDA_I2C3_SDA		0x400001C4>;
+	};
+
+	pinctrl_i2c3_gpio: i2c3gpiogrp {
+		fsl,pins = <MX8MN_IOMUXC_I2C3_SCL_GPIO5_IO18		0x400001C4>,
+			   <MX8MN_IOMUXC_I2C3_SDA_GPIO5_IO19		0x400001C4>;
+	};
+
+	pinctrl_pwm3: pwm3grp {
+		fsl,pins = <MX8MN_IOMUXC_GPIO1_IO14_PWM3_OUT		0x14>;
+	};
+
+	pinctrl_pwm4: pwm4grp {
+		fsl,pins = <MX8MN_IOMUXC_GPIO1_IO15_PWM4_OUT		0x14>;
+	};
+
+	pinctrl_sai3: sai3grp {
+		fsl,pins = <MX8MN_IOMUXC_SAI3_MCLK_SAI3_MCLK		0x94>,
+			   <MX8MN_IOMUXC_SAI3_RXC_SAI3_RX_BCLK		0x94>,
+			   <MX8MN_IOMUXC_SAI3_RXFS_SAI3_RX_SYNC		0x94>,
+			   <MX8MN_IOMUXC_SAI3_RXD_SAI3_RX_DATA0		0x94>,
+			   <MX8MN_IOMUXC_SAI3_TXFS_SAI3_TX_SYNC		0x94>,
+			   <MX8MN_IOMUXC_SAI3_TXD_SAI3_TX_DATA0		0x94>,
+			   <MX8MN_IOMUXC_SAI3_TXC_SAI3_TX_BCLK		0x94>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <MX8MN_IOMUXC_UART1_RXD_UART1_DCE_RX		0x16>,
+			   <MX8MN_IOMUXC_UART1_TXD_UART1_DCE_TX		0x16>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <MX8MN_IOMUXC_UART2_RXD_UART2_DCE_RX		0x16>,
+			   <MX8MN_IOMUXC_UART2_TXD_UART2_DCE_TX		0x16>;
+	};
+
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <MX8MN_IOMUXC_UART3_RXD_UART3_DCE_RX		0x16>,
+			   <MX8MN_IOMUXC_UART3_TXD_UART3_DCE_TX		0x16>;
+	};
+
+	pinctrl_uart4: uart4grp {
+		fsl,pins = <MX8MN_IOMUXC_UART4_RXD_UART4_DCE_RX		0x16>,
+			   <MX8MN_IOMUXC_UART4_TXD_UART4_DCE_TX		0x16>;
+	};
+
+	pinctrl_usb0hub_sel: usb0hub-selgrp {
+		/* SEL_USB_HUB_B */
+		fsl,pins = <MX8MN_IOMUXC_SD1_CMD_GPIO2_IO1		0x84>;
+	};
+
+	pinctrl_usbotg: usbotggrp {
+		fsl,pins = <MX8MN_IOMUXC_GPIO1_IO12_USB1_OTG_PWR	0x84>,
+			   <MX8MN_IOMUXC_GPIO1_IO13_USB1_OTG_OC		0x84>,
+			   <MX8MN_IOMUXC_GPIO1_IO10_USB1_OTG_ID		0x1C4>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <MX8MN_IOMUXC_SD2_CLK_USDHC2_CLK		0x1d4>,
+			   <MX8MN_IOMUXC_SD2_CMD_USDHC2_CMD		0x1d4>,
+			   <MX8MN_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d4>,
+			   <MX8MN_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d4>,
+			   <MX8MN_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d4>,
+			   <MX8MN_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d4>,
+			   <MX8MN_IOMUXC_GPIO1_IO04_USDHC2_VSELECT	0x84>;
+	};
+
+	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+		fsl,pins = <MX8MN_IOMUXC_SD2_CLK_USDHC2_CLK		0x1d4>,
+			   <MX8MN_IOMUXC_SD2_CMD_USDHC2_CMD		0x1d4>,
+			   <MX8MN_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d4>,
+			   <MX8MN_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d4>,
+			   <MX8MN_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d4>,
+			   <MX8MN_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d4>,
+			   <MX8MN_IOMUXC_GPIO1_IO04_USDHC2_VSELECT	0x84>;
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+		fsl,pins = <MX8MN_IOMUXC_SD2_CLK_USDHC2_CLK		0x1d4>,
+			   <MX8MN_IOMUXC_SD2_CMD_USDHC2_CMD		0x1d4>,
+			   <MX8MN_IOMUXC_SD2_DATA0_USDHC2_DATA0		0x1d4>,
+			   <MX8MN_IOMUXC_SD2_DATA1_USDHC2_DATA1		0x1d4>,
+			   <MX8MN_IOMUXC_SD2_DATA2_USDHC2_DATA2		0x1d4>,
+			   <MX8MN_IOMUXC_SD2_DATA3_USDHC2_DATA3		0x1d4>,
+			   <MX8MN_IOMUXC_GPIO1_IO04_USDHC2_VSELECT	0x84>;
+	};
+
+	pinctrl_usdhc2_gpio: usdhc2-gpiogrp {
+		fsl,pins = <MX8MN_IOMUXC_SD2_CD_B_GPIO2_IO12		0x84>;
+	};
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mn-tqma8mqnl.dtsi b/arch/arm64/boot/dts/freescale/imx8mn-tqma8mqnl.dtsi
new file mode 100644
index 000000000000..9ea28941068d
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mn-tqma8mqnl.dtsi
@@ -0,0 +1,322 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2020-2021 TQ-Systems GmbH
+ */
+
+#include "imx8mn.dtsi"
+
+/ {
+	model = "TQ-Systems i.MX8MN TQMa8MxNL";
+	compatible = "tq,imx8mn-tqma8mqnl", "fsl,imx8mn";
+
+	memory@40000000 {
+		device_type = "memory";
+		/*  our minimum RAM config will be 1024 MiB */
+		reg = <0x00000000 0x40000000 0 0x40000000>;
+	};
+
+	/* e-MMC IO, needed for HS modes */
+	reg_vcc1v8: regulator-vcc1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "TQMA8MXNL_VCC1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	reg_vcc3v3: regulator-vcc3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "TQMA8MXNL_VCC3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		/* global autoconfigured region for contiguous allocations */
+		linux,cma {
+			compatible = "shared-dma-pool";
+			reusable;
+			/* 640 MiB */
+			size = <0 0x28000000>;
+			/*  1024 - 128 MiB, our minimum RAM config will be 1024 MiB */
+			alloc-ranges = <0 0x40000000 0 0x78000000>;
+			linux,cma-default;
+		};
+	};
+};
+
+&A53_0 {
+	cpu-supply = <&buck2_reg>;
+};
+
+&flexspi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexspi>;
+	status = "okay";
+
+	flash0: flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		spi-max-frequency = <84000000>;
+		spi-tx-bus-width = <1>;
+		spi-rx-bus-width = <4>;
+	};
+};
+
+&i2c1 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	pinctrl-1 = <&pinctrl_i2c1_gpio>;
+	scl-gpios = <&gpio5 14 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio5 15 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "okay";
+
+	sensor0: temperature-sensor-eeprom@1b {
+		compatible = "nxp,se97", "jedec,jc-42.4-temp";
+		reg = <0x1b>;
+	};
+
+	pca9450: pmic@25 {
+		compatible = "nxp,pca9450a";
+		reg = <0x25>;
+
+		/* PMIC PCA9450 PMIC_nINT GPIO1_IO08 */
+		pinctrl-0 = <&pinctrl_pmic>;
+		pinctrl-names = "default";
+		interrupt-parent = <&gpio1>;
+		interrupts = <8 IRQ_TYPE_LEVEL_LOW>;
+
+		regulators {
+			/* V_0V85_SOC: 0.85 .. 0.95 */
+			buck1_reg: BUCK1 {
+				regulator-name = "BUCK1";
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <950000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <3125>;
+			};
+
+			/* VDD_ARM */
+			buck2_reg: BUCK2 {
+				regulator-name = "BUCK2";
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-boot-on;
+				regulator-always-on;
+				nxp,dvs-run-voltage = <950000>;
+				nxp,dvs-standby-voltage = <850000>;
+				regulator-ramp-delay = <3125>;
+			};
+
+			/* V_0V85_GPU / DRAM: shall be equal to BUCK1 for i.MX8MN */
+			buck3_reg: BUCK3 {
+				regulator-name = "BUCK3";
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <950000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <3125>;
+			};
+
+			/* VCC3V3 -> VMMC, ... must not be changed */
+			buck4_reg: BUCK4 {
+				regulator-name = "BUCK4";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			/* V_1V8 -> VQMMC, SPI-NOR, ... must not be changed */
+			buck5_reg: BUCK5 {
+				regulator-name = "BUCK5";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			/* V_1V1 -> RAM, ... must not be changed */
+			buck6_reg: BUCK6 {
+				regulator-name = "BUCK6";
+				regulator-min-microvolt = <1100000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			/* V_1V8_SNVS */
+			ldo1_reg: LDO1 {
+				regulator-name = "LDO1";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			/* V_0V8_SNVS */
+			ldo2_reg: LDO2 {
+				regulator-name = "LDO2";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <850000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			/* V_1V8_ANA */
+			ldo3_reg: LDO3 {
+				regulator-name = "LDO3";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			/* V_0V9_MIPI */
+			ldo4_reg: LDO4 {
+				regulator-name = "LDO4";
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <900000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			/* VCC SD IO - switched using SD2 VSELECT */
+			ldo5_reg: LDO5 {
+				regulator-name = "LDO5";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+			};
+		};
+	};
+
+	pcf85063: rtc@51 {
+		compatible = "nxp,pcf85063a";
+		reg = <0x51>;
+		quartz-load-femtofarads = <7000>;
+	};
+
+	eeprom1: eeprom@53 {
+		compatible = "nxp,se97b", "atmel,24c02";
+		read-only;
+		reg = <0x53>;
+		pagesize = <16>;
+	};
+
+	eeprom0: eeprom@57 {
+		compatible = "atmel,24c64";
+		reg = <0x57>;
+		pagesize = <32>;
+	};
+};
+
+&usdhc3 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+	bus-width = <8>;
+	non-removable;
+	no-sd;
+	no-sdio;
+	vmmc-supply = <&reg_vcc3v3>;
+	vqmmc-supply = <&reg_vcc1v8>;
+	status = "okay";
+};
+
+/*
+ * Attention:
+ * wdog reset is routed to PMIC, PMIC must be preconfigured to force POR
+ * without LDO for SNVS. GPIO1_IO02 must not be used as GPIO.
+ */
+&wdog1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog>;
+	fsl,ext-reset-output;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_flexspi: flexspigrp {
+		fsl,pins = <MX8MN_IOMUXC_NAND_ALE_QSPI_A_SCLK		0x84>,
+			   <MX8MN_IOMUXC_NAND_CE0_B_QSPI_A_SS0_B	0x84>,
+			   <MX8MN_IOMUXC_NAND_DATA00_QSPI_A_DATA0	0x84>,
+			   <MX8MN_IOMUXC_NAND_DATA01_QSPI_A_DATA1	0x84>,
+			   <MX8MN_IOMUXC_NAND_DATA02_QSPI_A_DATA2	0x84>,
+			   <MX8MN_IOMUXC_NAND_DATA03_QSPI_A_DATA3	0x84>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <MX8MN_IOMUXC_I2C1_SCL_I2C1_SCL		0x400001c4>,
+			   <MX8MN_IOMUXC_I2C1_SDA_I2C1_SDA		0x400001c4>;
+	};
+
+	pinctrl_i2c1_gpio: i2c1gpiogrp {
+		fsl,pins = <MX8MN_IOMUXC_I2C1_SCL_GPIO5_IO14	0x400001c4>,
+			   <MX8MN_IOMUXC_I2C1_SDA_GPIO5_IO15	0x400001c4>;
+	};
+
+	pinctrl_pmic: pmicgrp {
+		fsl,pins = <MX8MN_IOMUXC_GPIO1_IO08_GPIO1_IO8	0x84>;
+	};
+
+	pinctrl_reg_usdhc2_vmmc: regusdhc2vmmcgrp {
+		fsl,pins = <MX8MN_IOMUXC_SD2_RESET_B_GPIO2_IO19		0x84>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <MX8MN_IOMUXC_NAND_WE_B_USDHC3_CLK		0x1d4>,
+			   <MX8MN_IOMUXC_NAND_WP_B_USDHC3_CMD		0x1d2>,
+			   <MX8MN_IOMUXC_NAND_DATA04_USDHC3_DATA0	0x1d4>,
+			   <MX8MN_IOMUXC_NAND_DATA05_USDHC3_DATA1	0x1d4>,
+			   <MX8MN_IOMUXC_NAND_DATA06_USDHC3_DATA2	0x1d4>,
+			   <MX8MN_IOMUXC_NAND_DATA07_USDHC3_DATA3	0x1d4>,
+			   <MX8MN_IOMUXC_NAND_RE_B_USDHC3_DATA4		0x1d4>,
+			   <MX8MN_IOMUXC_NAND_CE2_B_USDHC3_DATA5	0x1d4>,
+			   <MX8MN_IOMUXC_NAND_CE3_B_USDHC3_DATA6	0x1d4>,
+			   <MX8MN_IOMUXC_NAND_CLE_USDHC3_DATA7		0x1d4>,
+			   <MX8MN_IOMUXC_NAND_CE1_B_USDHC3_STROBE	0x84>,
+			   <MX8MN_IOMUXC_NAND_READY_B_USDHC3_RESET_B	0x84>;
+	};
+
+	pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
+		fsl,pins = <MX8MN_IOMUXC_NAND_WE_B_USDHC3_CLK		0x1d2>,
+			   <MX8MN_IOMUXC_NAND_WP_B_USDHC3_CMD		0x1d2>,
+			   <MX8MN_IOMUXC_NAND_DATA04_USDHC3_DATA0	0x1d4>,
+			   <MX8MN_IOMUXC_NAND_DATA05_USDHC3_DATA1	0x1d4>,
+			   <MX8MN_IOMUXC_NAND_DATA06_USDHC3_DATA2	0x1d4>,
+			   <MX8MN_IOMUXC_NAND_DATA07_USDHC3_DATA3	0x1d4>,
+			   <MX8MN_IOMUXC_NAND_RE_B_USDHC3_DATA4		0x1d4>,
+			   <MX8MN_IOMUXC_NAND_CE2_B_USDHC3_DATA5	0x1d4>,
+			   <MX8MN_IOMUXC_NAND_CE3_B_USDHC3_DATA6	0x1d4>,
+			   <MX8MN_IOMUXC_NAND_CLE_USDHC3_DATA7		0x1d4>,
+			   <MX8MN_IOMUXC_NAND_CE1_B_USDHC3_STROBE	0x84>,
+			   <MX8MN_IOMUXC_NAND_READY_B_USDHC3_RESET_B	0x84>;
+	};
+
+	pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
+		fsl,pins = <MX8MN_IOMUXC_NAND_WE_B_USDHC3_CLK		0x1d6>,
+			   <MX8MN_IOMUXC_NAND_WP_B_USDHC3_CMD		0x1d2>,
+			   <MX8MN_IOMUXC_NAND_DATA04_USDHC3_DATA0	0x1d4>,
+			   <MX8MN_IOMUXC_NAND_DATA05_USDHC3_DATA1	0x1d4>,
+			   <MX8MN_IOMUXC_NAND_DATA06_USDHC3_DATA2	0x1d4>,
+			   <MX8MN_IOMUXC_NAND_DATA07_USDHC3_DATA3	0x1d4>,
+			   <MX8MN_IOMUXC_NAND_RE_B_USDHC3_DATA4		0x1d4>,
+			   <MX8MN_IOMUXC_NAND_CE2_B_USDHC3_DATA5	0x1d4>,
+			   <MX8MN_IOMUXC_NAND_CE3_B_USDHC3_DATA6	0x1d4>,
+			   <MX8MN_IOMUXC_NAND_CLE_USDHC3_DATA7		0x1d4>,
+			   <MX8MN_IOMUXC_NAND_CE1_B_USDHC3_STROBE	0x84>,
+			   <MX8MN_IOMUXC_NAND_READY_B_USDHC3_RESET_B	0x84>;
+	};
+
+	pinctrl_wdog: wdoggrp {
+		fsl,pins = <MX8MN_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B	0x84>;
+	};
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mn-var-som-symphony.dts b/arch/arm64/boot/dts/freescale/imx8mn-var-som-symphony.dts
index f61c48776cf3..3ed7021a487c 100644
--- a/arch/arm64/boot/dts/freescale/imx8mn-var-som-symphony.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mn-var-som-symphony.dts
@@ -26,19 +26,19 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		back {
+		key-back {
 			label = "Back";
 			gpios = <&pca9534 1 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_BACK>;
 		};
 
-		home {
+		key-home {
 			label = "Home";
 			gpios = <&pca9534 2 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_HOME>;
 		};
 
-		menu {
+		key-menu {
 			label = "Menu";
 			gpios = <&pca9534 3 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_MENU>;
diff --git a/arch/arm64/boot/dts/freescale/imx8mn-var-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mn-var-som.dtsi
index b16c7caf34c1..87b5e23c766f 100644
--- a/arch/arm64/boot/dts/freescale/imx8mn-var-som.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mn-var-som.dtsi
@@ -70,12 +70,12 @@
 		pendown-gpio = <&gpio1 3 GPIO_ACTIVE_LOW>;
 
 		ti,x-min = /bits/ 16 <125>;
-		touchscreen-size-x = /bits/ 16 <4008>;
+		touchscreen-size-x = <4008>;
 		ti,y-min = /bits/ 16 <282>;
-		touchscreen-size-y = /bits/ 16 <3864>;
+		touchscreen-size-y = <3864>;
 		ti,x-plate-ohms = /bits/ 16 <180>;
-		touchscreen-max-pressure = /bits/ 16 <255>;
-		touchscreen-average-samples = /bits/ 16 <10>;
+		touchscreen-max-pressure = <255>;
+		touchscreen-average-samples = <10>;
 		ti,debounce-tol = /bits/ 16 <3>;
 		ti,debounce-rep = /bits/ 16 <1>;
 		ti,settle-delay-usec = /bits/ 16 <150>;
diff --git a/arch/arm64/boot/dts/freescale/imx8mn-venice-gw7902.dts b/arch/arm64/boot/dts/freescale/imx8mn-venice-gw7902.dts
index 236f425e1570..dd4302ac1de4 100644
--- a/arch/arm64/boot/dts/freescale/imx8mn-venice-gw7902.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mn-venice-gw7902.dts
@@ -39,13 +39,13 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		user-pb {
+		key-user-pb {
 			label = "user_pb";
 			gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
 			linux,code = <BTN_0>;
 		};
 
-		user-pb1x {
+		key-user-pb1x {
 			label = "user_pb1x";
 			linux,code = <BTN_1>;
 			interrupt-parent = <&gsc>;
@@ -59,14 +59,14 @@
 			interrupts = <1>;
 		};
 
-		eeprom-wp {
+		key-eeprom-wp {
 			label = "eeprom_wp";
 			linux,code = <BTN_3>;
 			interrupt-parent = <&gsc>;
 			interrupts = <2>;
 		};
 
-		tamper {
+		key-tamper {
 			label = "tamper";
 			linux,code = <BTN_4>;
 			interrupt-parent = <&gsc>;
@@ -213,13 +213,16 @@
 		compatible = "microchip,mcp2515";
 		reg = <0>;
 		clocks = <&can20m>;
-		oscillator-frequency = <20000000>;
 		interrupt-parent = <&gpio2>;
 		interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
 		spi-max-frequency = <10000000>;
 	};
 };
 
+&disp_blk_ctrl {
+	status = "disabled";
+};
+
 /* off-board header */
 &ecspi2 {
 	pinctrl-names = "default";
@@ -251,6 +254,47 @@
 	};
 };
 
+&gpio1 {
+	gpio-line-names = "", "", "", "", "", "", "", "",
+		"", "", "", "", "", "m2_reset", "", "m2_wdis#",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "";
+};
+
+&gpio2 {
+	gpio-line-names = "", "", "", "", "", "", "", "",
+		"uart2_en#", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "";
+};
+
+&gpio3 {
+	gpio-line-names = "", "m2_gdis#", "", "", "", "", "", "m2_off#",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "";
+};
+
+&gpio4 {
+	gpio-line-names = "", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "app_gpio1", "", "uart1_rs485",
+		"", "uart1_term", "uart1_half", "app_gpio2",
+		"mipi_gpio1", "", "", "";
+};
+
+&gpio5 {
+	gpio-line-names = "", "", "", "mipi_gpio4",
+		"mipi_gpio3", "mipi_gpio2", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "";
+};
+
+&gpu {
+	status = "disabled";
+};
+
 &i2c1 {
 	clock-frequency = <100000>;
 	pinctrl-names = "default";
@@ -348,6 +392,13 @@
 				gw,voltage-divider-ohms = <10000 10000>;
 			};
 
+			channel@9c {
+				gw,mode = <2>;
+				reg = <0x9c>;
+				label = "vdd_5p0";
+				gw,voltage-divider-ohms = <10000 10000>;
+			};
+
 			channel@a2 {
 				gw,mode = <2>;
 				reg = <0xa2>;
@@ -546,6 +597,10 @@
 	status = "okay";
 };
 
+&pgc_gpumix {
+	status = "disabled";
+};
+
 /* off-board header */
 &sai3 {
 	pinctrl-names = "default";
@@ -576,6 +631,7 @@
 	pinctrl-0 = <&pinctrl_uart3>, <&pinctrl_uart3_gpio>;
 	rts-gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
 	cts-gpios = <&gpio2 0 GPIO_ACTIVE_LOW>;
+	uart-has-rtscts;
 	status = "okay";
 
 	bluetooth {
@@ -633,7 +689,7 @@
 	pinctrl_hog: hoggrp {
 		fsl,pins = <
 			MX8MN_IOMUXC_NAND_CE0_B_GPIO3_IO1	0x40000159 /* M2_GDIS# */
-			MX8MN_IOMUXC_GPIO1_IO13_GPIO1_IO13	0x40000041 /* M2_RST# */
+			MX8MN_IOMUXC_GPIO1_IO13_GPIO1_IO13	0x40000041 /* M2_RESET */
 			MX8MN_IOMUXC_NAND_DATA01_GPIO3_IO7	0x40000119 /* M2_OFF# */
 			MX8MN_IOMUXC_GPIO1_IO15_GPIO1_IO15	0x40000159 /* M2_WDIS# */
 			MX8MN_IOMUXC_SAI2_RXFS_GPIO4_IO21	0x40000041 /* APP GPIO1 */
diff --git a/arch/arm64/boot/dts/freescale/imx8mn.dtsi b/arch/arm64/boot/dts/freescale/imx8mn.dtsi
index da6c942fb7f9..ad0b99adf691 100644
--- a/arch/arm64/boot/dts/freescale/imx8mn.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mn.dtsi
@@ -4,6 +4,8 @@
  */
 
 #include <dt-bindings/clock/imx8mn-clock.h>
+#include <dt-bindings/power/imx8mn-power.h>
+#include <dt-bindings/reset/imx8mq-reset.h>
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
@@ -63,6 +65,12 @@
 			clock-latency = <61036>;
 			clocks = <&clk IMX8MN_CLK_ARM>;
 			enable-method = "psci";
+			i-cache-size = <0x8000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <128>;
 			next-level-cache = <&A53_L2>;
 			operating-points-v2 = <&a53_opp_table>;
 			nvmem-cells = <&cpu_speed_grade>;
@@ -78,6 +86,12 @@
 			clock-latency = <61036>;
 			clocks = <&clk IMX8MN_CLK_ARM>;
 			enable-method = "psci";
+			i-cache-size = <0x8000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <128>;
 			next-level-cache = <&A53_L2>;
 			operating-points-v2 = <&a53_opp_table>;
 			cpu-idle-states = <&cpu_pd_wait>;
@@ -91,6 +105,12 @@
 			clock-latency = <61036>;
 			clocks = <&clk IMX8MN_CLK_ARM>;
 			enable-method = "psci";
+			i-cache-size = <0x8000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <128>;
 			next-level-cache = <&A53_L2>;
 			operating-points-v2 = <&a53_opp_table>;
 			cpu-idle-states = <&cpu_pd_wait>;
@@ -104,6 +124,12 @@
 			clock-latency = <61036>;
 			clocks = <&clk IMX8MN_CLK_ARM>;
 			enable-method = "psci";
+			i-cache-size = <0x8000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <128>;
 			next-level-cache = <&A53_L2>;
 			operating-points-v2 = <&a53_opp_table>;
 			cpu-idle-states = <&cpu_pd_wait>;
@@ -112,6 +138,10 @@
 
 		A53_L2: l2-cache0 {
 			compatible = "cache";
+			cache-level = <2>;
+			cache-size = <0x80000>;
+			cache-line-size = <64>;
+			cache-sets = <512>;
 		};
 	};
 
@@ -182,7 +212,7 @@
 	clk_ext4: clock-ext4 {
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
-		clock-frequency= <133000000>;
+		clock-frequency = <133000000>;
 		clock-output-names = "clk_ext4";
 	};
 
@@ -239,7 +269,7 @@
 		arm,no-tick-in-suspend;
 	};
 
-	soc@0 {
+	soc: soc@0 {
 		compatible = "fsl,imx8mn-soc", "simple-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -263,7 +293,7 @@
 				ranges;
 
 				sai2: sai@30020000 {
-					compatible = "fsl,imx8mm-sai", "fsl,imx8mq-sai";
+					compatible = "fsl,imx8mn-sai", "fsl,imx8mq-sai";
 					reg = <0x30020000 0x10000>;
 					interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
 					clocks = <&clk IMX8MN_CLK_SAI2_IPG>,
@@ -277,7 +307,7 @@
 				};
 
 				sai3: sai@30030000 {
-					compatible = "fsl,imx8mm-sai", "fsl,imx8mq-sai";
+					compatible = "fsl,imx8mn-sai", "fsl,imx8mq-sai";
 					reg = <0x30030000 0x10000>;
 					interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
 					clocks = <&clk IMX8MN_CLK_SAI3_IPG>,
@@ -291,7 +321,7 @@
 				};
 
 				sai5: sai@30050000 {
-					compatible = "fsl,imx8mm-sai", "fsl,imx8mq-sai";
+					compatible = "fsl,imx8mn-sai", "fsl,imx8mq-sai";
 					reg = <0x30050000 0x10000>;
 					interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>;
 					clocks = <&clk IMX8MN_CLK_SAI5_IPG>,
@@ -307,7 +337,7 @@
 				};
 
 				sai6: sai@30060000 {
-					compatible = "fsl,imx8mm-sai", "fsl,imx8mq-sai";
+					compatible = "fsl,imx8mn-sai", "fsl,imx8mq-sai";
 					reg = <0x30060000  0x10000>;
 					interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>;
 					clocks = <&clk IMX8MN_CLK_SAI6_IPG>,
@@ -364,7 +394,7 @@
 				};
 
 				sai7: sai@300b0000 {
-					compatible = "fsl,imx8mm-sai", "fsl,imx8mq-sai";
+					compatible = "fsl,imx8mn-sai", "fsl,imx8mq-sai";
 					reg = <0x300b0000 0x10000>;
 					interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
 					clocks = <&clk IMX8MN_CLK_SAI7_IPG>,
@@ -392,7 +422,7 @@
 						    "ctx2_rx", "ctx2_tx",
 						    "ctx3_rx", "ctx3_tx";
 					firmware-name = "imx/easrc/easrc-imx8mn.bin";
-					fsl,asrc-rate  = <8000>;
+					fsl,asrc-rate = <8000>;
 					fsl,asrc-format = <2>;
 					status = "disabled";
 				};
@@ -612,6 +642,51 @@
 				interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
 				#reset-cells = <1>;
 			};
+
+			gpc: gpc@303a0000 {
+				compatible = "fsl,imx8mn-gpc";
+				reg = <0x303a0000 0x10000>;
+				interrupt-parent = <&gic>;
+				interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
+
+				pgc {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					pgc_hsiomix: power-domain@0 {
+						#power-domain-cells = <0>;
+						reg = <IMX8MN_POWER_DOMAIN_HSIOMIX>;
+						clocks = <&clk IMX8MN_CLK_USB_BUS>;
+					};
+
+					pgc_otg1: power-domain@1 {
+						#power-domain-cells = <0>;
+						reg = <IMX8MN_POWER_DOMAIN_OTG1>;
+					};
+
+					pgc_gpumix: power-domain@2 {
+						#power-domain-cells = <0>;
+						reg = <IMX8MN_POWER_DOMAIN_GPUMIX>;
+						clocks = <&clk IMX8MN_CLK_GPU_CORE_ROOT>,
+							 <&clk IMX8MN_CLK_GPU_SHADER>,
+							 <&clk IMX8MN_CLK_GPU_BUS_ROOT>,
+							 <&clk IMX8MN_CLK_GPU_AHB>;
+					};
+
+					pgc_dispmix: power-domain@3 {
+						#power-domain-cells = <0>;
+						reg = <IMX8MN_POWER_DOMAIN_DISPMIX>;
+						clocks = <&clk IMX8MN_CLK_DISP_AXI_ROOT>,
+							 <&clk IMX8MN_CLK_DISP_APB_ROOT>;
+					};
+
+					pgc_mipi: power-domain@4 {
+						#power-domain-cells = <0>;
+						reg = <IMX8MN_POWER_DOMAIN_MIPI>;
+						power-domains = <&pgc_dispmix>;
+					};
+				};
+			};
 		};
 
 		aips2: bus@30400000 {
@@ -628,7 +703,7 @@
 				clocks = <&clk IMX8MN_CLK_PWM1_ROOT>,
 					<&clk IMX8MN_CLK_PWM1_ROOT>;
 				clock-names = "ipg", "per";
-				#pwm-cells = <2>;
+				#pwm-cells = <3>;
 				status = "disabled";
 			};
 
@@ -639,7 +714,7 @@
 				clocks = <&clk IMX8MN_CLK_PWM2_ROOT>,
 					 <&clk IMX8MN_CLK_PWM2_ROOT>;
 				clock-names = "ipg", "per";
-				#pwm-cells = <2>;
+				#pwm-cells = <3>;
 				status = "disabled";
 			};
 
@@ -650,7 +725,7 @@
 				clocks = <&clk IMX8MN_CLK_PWM3_ROOT>,
 					 <&clk IMX8MN_CLK_PWM3_ROOT>;
 				clock-names = "ipg", "per";
-				#pwm-cells = <2>;
+				#pwm-cells = <3>;
 				status = "disabled";
 			};
 
@@ -661,7 +736,7 @@
 				clocks = <&clk IMX8MN_CLK_PWM4_ROOT>,
 					 <&clk IMX8MN_CLK_PWM4_ROOT>;
 				clock-names = "ipg", "per";
-				#pwm-cells = <2>;
+				#pwm-cells = <3>;
 				status = "disabled";
 			};
 
@@ -780,6 +855,7 @@
 					 compatible = "fsl,sec-v4.0-job-ring";
 					 reg = <0x1000 0x1000>;
 					 interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>;
+					 status = "disabled";
 				};
 
 				sec_jr1: jr@2000 {
@@ -856,7 +932,7 @@
 			};
 
 			usdhc1: mmc@30b40000 {
-				compatible = "fsl,imx8mn-usdhc", "fsl,imx7d-usdhc";
+				compatible = "fsl,imx8mn-usdhc", "fsl,imx8mm-usdhc", "fsl,imx7d-usdhc";
 				reg = <0x30b40000 0x10000>;
 				interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clk IMX8MN_CLK_IPG_ROOT>,
@@ -864,13 +940,13 @@
 					 <&clk IMX8MN_CLK_USDHC1_ROOT>;
 				clock-names = "ipg", "ahb", "per";
 				fsl,tuning-start-tap = <20>;
-				fsl,tuning-step= <2>;
+				fsl,tuning-step = <2>;
 				bus-width = <4>;
 				status = "disabled";
 			};
 
 			usdhc2: mmc@30b50000 {
-				compatible = "fsl,imx8mn-usdhc", "fsl,imx7d-usdhc";
+				compatible = "fsl,imx8mn-usdhc", "fsl,imx8mm-usdhc", "fsl,imx7d-usdhc";
 				reg = <0x30b50000 0x10000>;
 				interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clk IMX8MN_CLK_IPG_ROOT>,
@@ -878,13 +954,13 @@
 					 <&clk IMX8MN_CLK_USDHC2_ROOT>;
 				clock-names = "ipg", "ahb", "per";
 				fsl,tuning-start-tap = <20>;
-				fsl,tuning-step= <2>;
+				fsl,tuning-step = <2>;
 				bus-width = <4>;
 				status = "disabled";
 			};
 
 			usdhc3: mmc@30b60000 {
-				compatible = "fsl,imx8mn-usdhc", "fsl,imx7d-usdhc";
+				compatible = "fsl,imx8mn-usdhc", "fsl,imx8mm-usdhc", "fsl,imx7d-usdhc";
 				reg = <0x30b60000 0x10000>;
 				interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clk IMX8MN_CLK_IPG_ROOT>,
@@ -892,7 +968,7 @@
 					 <&clk IMX8MN_CLK_USDHC3_ROOT>;
 				clock-names = "ipg", "ahb", "per";
 				fsl,tuning-start-tap = <20>;
-				fsl,tuning-step= <2>;
+				fsl,tuning-step = <2>;
 				bus-width = <4>;
 				status = "disabled";
 			};
@@ -948,7 +1024,6 @@
 				fsl,num-rx-queues = <3>;
 				nvmem-cells = <&fec_mac_address>;
 				nvmem-cell-names = "mac-address";
-				nvmem_macaddr_swap;
 				fsl,stop-mode = <&gpr 0x10 3>;
 				status = "disabled";
 			};
@@ -962,6 +1037,34 @@
 			#size-cells = <1>;
 			ranges;
 
+			disp_blk_ctrl: blk-ctrl@32e28000 {
+				compatible = "fsl,imx8mn-disp-blk-ctrl", "syscon";
+				reg = <0x32e28000 0x100>;
+				power-domains = <&pgc_dispmix>, <&pgc_dispmix>,
+						<&pgc_dispmix>, <&pgc_mipi>,
+						<&pgc_mipi>;
+				power-domain-names = "bus", "isi",
+						     "lcdif", "mipi-dsi",
+						     "mipi-csi";
+				clocks = <&clk IMX8MN_CLK_DISP_AXI>,
+					 <&clk IMX8MN_CLK_DISP_APB>,
+					 <&clk IMX8MN_CLK_DISP_AXI_ROOT>,
+					 <&clk IMX8MN_CLK_DISP_APB_ROOT>,
+					 <&clk IMX8MN_CLK_DISP_AXI_ROOT>,
+					 <&clk IMX8MN_CLK_DISP_APB_ROOT>,
+					 <&clk IMX8MN_CLK_DISP_PIXEL_ROOT>,
+					 <&clk IMX8MN_CLK_DSI_CORE>,
+					 <&clk IMX8MN_CLK_DSI_PHY_REF>,
+					 <&clk IMX8MN_CLK_CSI1_PHY_REF>,
+					 <&clk IMX8MN_CLK_CAMERA_PIXEL_ROOT>;
+				clock-names = "disp_axi", "disp_apb",
+					      "disp_axi_root", "disp_apb_root",
+					      "lcdif-axi", "lcdif-apb", "lcdif-pix",
+					      "dsi-pclk", "dsi-ref",
+					      "csi-aclk", "csi-pclk";
+				#power-domain-cells = <1>;
+			};
+
 			usbotg1: usb@32e40000 {
 				compatible = "fsl,imx8mn-usb", "fsl,imx7d-usb";
 				reg = <0x32e40000 0x200>;
@@ -972,6 +1075,7 @@
 				assigned-clock-parents = <&clk IMX8MN_SYS_PLL2_500M>;
 				phys = <&usbphynop1>;
 				fsl,usbmisc = <&usbmisc1 0>;
+				power-domains = <&pgc_hsiomix>;
 				status = "disabled";
 			};
 
@@ -1011,6 +1115,32 @@
 			status = "disabled";
 		};
 
+		gpu: gpu@38000000 {
+			compatible = "vivante,gc";
+			reg = <0x38000000 0x8000>;
+			interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk IMX8MN_CLK_GPU_AHB>,
+				<&clk IMX8MN_CLK_GPU_BUS_ROOT>,
+				<&clk IMX8MN_CLK_GPU_CORE_ROOT>,
+				<&clk IMX8MN_CLK_GPU_SHADER>;
+			clock-names = "reg", "bus", "core", "shader";
+			assigned-clocks = <&clk IMX8MN_CLK_GPU_CORE>,
+					  <&clk IMX8MN_CLK_GPU_SHADER>,
+					  <&clk IMX8MN_CLK_GPU_AXI>,
+					  <&clk IMX8MN_CLK_GPU_AHB>,
+					  <&clk IMX8MN_GPU_PLL>;
+			assigned-clock-parents = <&clk IMX8MN_GPU_PLL_OUT>,
+						  <&clk IMX8MN_GPU_PLL_OUT>,
+						  <&clk IMX8MN_SYS_PLL1_800M>,
+						  <&clk IMX8MN_SYS_PLL1_800M>;
+			assigned-clock-rates = <400000000>,
+					       <400000000>,
+					       <800000000>,
+					       <400000000>,
+					       <1200000000>;
+			power-domains = <&pgc_gpumix>;
+		};
+
 		gic: interrupt-controller@38800000 {
 			compatible = "arm,gic-v3";
 			reg = <0x38800000 0x10000>,
@@ -1044,5 +1174,6 @@
 		assigned-clocks = <&clk IMX8MN_CLK_USB_PHY_REF>;
 		assigned-clock-parents = <&clk IMX8MN_SYS_PLL1_100M>;
 		clock-names = "main_clk";
+		power-domains = <&pgc_otg1>;
 	};
 };
diff --git a/arch/arm64/boot/dts/freescale/imx8mp-dhcom-pdk2.dts b/arch/arm64/boot/dts/freescale/imx8mp-dhcom-pdk2.dts
new file mode 100644
index 000000000000..382fbedaf6ba
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mp-dhcom-pdk2.dts
@@ -0,0 +1,168 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2022 Marek Vasut <marex@denx.de>
+ *
+ * DHCOM iMX8MP variant:
+ * DHCM-iMX8ML8-C160-R409-F1638-SPI16-GE-CAN2-SD-RTC-WBTA-ADC-T-RGB-CSI2-HS-I-01D2
+ * DHCOM PCB number: 660-100 or newer
+ * PDK2 PCB number: 516-400 or newer
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/phy/phy-imx8-pcie.h>
+#include "imx8mp-dhcom-som.dtsi"
+
+/ {
+	model = "DH electronics i.MX8M Plus DHCOM Premium Developer Kit (2)";
+	compatible = "dh,imx8mp-dhcom-pdk2", "dh,imx8mp-dhcom-som",
+		     "fsl,imx8mp";
+
+	chosen {
+		stdout-path = &uart1;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-0 {
+			gpios = <&gpio1 9 GPIO_ACTIVE_LOW>; /* GPIO A */
+			label = "TA1-GPIO-A";
+			linux,code = <KEY_A>;
+			pinctrl-0 = <&pinctrl_dhcom_a>;
+			pinctrl-names = "default";
+			wakeup-source;
+		};
+
+		button-1 {
+			gpios = <&gpio1 8 GPIO_ACTIVE_LOW>; /* GPIO B */
+			label = "TA2-GPIO-B";
+			linux,code = <KEY_B>;
+			pinctrl-0 = <&pinctrl_dhcom_b>;
+			pinctrl-names = "default";
+			wakeup-source;
+		};
+
+		button-2 {
+			gpios = <&gpio5 2 GPIO_ACTIVE_LOW>; /* GPIO C */
+			label = "TA3-GPIO-C";
+			linux,code = <KEY_C>;
+			pinctrl-0 = <&pinctrl_dhcom_c>;
+			pinctrl-names = "default";
+			wakeup-source;
+		};
+
+		button-3 {
+			gpios = <&gpio4 27 GPIO_ACTIVE_LOW>; /* GPIO D */
+			label = "TA4-GPIO-D";
+			linux,code = <KEY_D>;
+			pinctrl-0 = <&pinctrl_dhcom_d>;
+			pinctrl-names = "default";
+			wakeup-source;
+		};
+	};
+
+	led {
+		compatible = "gpio-leds";
+
+		led-0 {
+			color = <LED_COLOR_ID_GREEN>;
+			default-state = "off";
+			function = LED_FUNCTION_INDICATOR;
+			gpios = <&gpio5 22 GPIO_ACTIVE_HIGH>; /* GPIO E */
+			pinctrl-0 = <&pinctrl_dhcom_e>;
+			pinctrl-names = "default";
+		};
+
+		led-1 {
+			color = <LED_COLOR_ID_GREEN>;
+			default-state = "off";
+			function = LED_FUNCTION_INDICATOR;
+			gpios = <&gpio5 23 GPIO_ACTIVE_HIGH>; /* GPIO F */
+			pinctrl-0 = <&pinctrl_dhcom_f>;
+			pinctrl-names = "default";
+		};
+
+		led-2 {
+			color = <LED_COLOR_ID_GREEN>;
+			default-state = "off";
+			function = LED_FUNCTION_INDICATOR;
+			gpios = <&gpio1 11 GPIO_ACTIVE_HIGH>; /* GPIO H */
+			pinctrl-0 = <&pinctrl_dhcom_h>;
+			pinctrl-names = "default";
+		};
+
+		led-3 {
+			color = <LED_COLOR_ID_GREEN>;
+			default-state = "off";
+			function = LED_FUNCTION_INDICATOR;
+			gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>; /* GPIO I */
+			pinctrl-0 = <&pinctrl_dhcom_i>;
+			pinctrl-names = "default";
+		};
+	};
+};
+
+/*
+ * PDK2 carrier board uses SoM with KSZ9131 populated and connected to
+ * SoM EQoS ethernet RGMII interface. Remove the other SoM PHY DT node.
+ */
+/delete-node/ &ethphy0f;
+
+/*
+ * PDK2 carrier board has KSZ9021 PHY populated and connected to SoM FEC
+ * ethernet RGMII interface. The SoM is not populated with second FEC PHY.
+ */
+/delete-node/ &ethphy1f;
+
+&fec {	/* Second ethernet */
+	phy-handle = <&ethphypdk>;
+
+	mdio {
+		ethphypdk: ethernet-phy@7 { /* KSZ 9021 */
+			compatible = "ethernet-phy-ieee802.3-c22";
+			pinctrl-0 = <&pinctrl_ethphy1>;
+			pinctrl-names = "default";
+			interrupt-parent = <&gpio4>;
+			interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
+			max-speed = <100>;
+			reg = <7>;
+			reset-assert-us = <1000>;
+			reset-deassert-us = <1000>;
+			reset-gpios = <&gpio4 2 GPIO_ACTIVE_LOW>;
+			rxc-skew-ps = <3000>;
+			rxd0-skew-ps = <0>;
+			rxd1-skew-ps = <0>;
+			rxd2-skew-ps = <0>;
+			rxd3-skew-ps = <0>;
+			rxdv-skew-ps = <0>;
+			txc-skew-ps = <3000>;
+			txd0-skew-ps = <0>;
+			txd1-skew-ps = <0>;
+			txd2-skew-ps = <0>;
+			txd3-skew-ps = <0>;
+			txen-skew-ps = <0>;
+		};
+	};
+};
+
+&flexcan1 {
+	status = "okay";
+};
+
+&usb3_1 {
+	fsl,over-current-active-low;
+};
+
+&iomuxc {
+	/*
+	 * GPIO_A,B,C,D are connected to buttons.
+	 * GPIO_E,F,H,I are connected to LEDs.
+	 * GPIO_M is connected to CLKOUT2.
+	 */
+	pinctrl-0 = <&pinctrl_hog_base
+		     &pinctrl_dhcom_g &pinctrl_dhcom_j
+		     &pinctrl_dhcom_k &pinctrl_dhcom_l
+		     &pinctrl_dhcom_int>;
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mp-dhcom-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-dhcom-som.dtsi
new file mode 100644
index 000000000000..0f13ee362771
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mp-dhcom-som.dtsi
@@ -0,0 +1,1030 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2021-2022 Marek Vasut <marex@denx.de>
+ */
+
+#include "imx8mp.dtsi"
+
+/ {
+	model = "DH electronics i.MX8M Plus DHCOM SoM";
+	compatible = "dh,imx8mp-dhcom-som", "fsl,imx8mp";
+
+	aliases {
+		ethernet0 = &eqos;
+		ethernet1 = &fec;
+		rtc0 = &rv3032;
+		rtc1 = &snvs_rtc;
+		spi0 = &flexspi;
+	};
+
+	memory@40000000 {
+		device_type = "memory";
+		/* Memory size 512 MiB..8 GiB will be filled by U-Boot */
+		reg = <0x0 0x40000000 0 0x08000000>;
+	};
+
+	reg_eth_vio: regulator-eth-vio {
+		compatible = "regulator-fixed";
+		gpio = <&gpio2 10 GPIO_ACTIVE_LOW>;
+		pinctrl-0 = <&pinctrl_enet_vio>;
+		pinctrl-names = "default";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-name = "eth_vio";
+		vin-supply = <&buck4>;
+	};
+
+	reg_usdhc2_vmmc: regulator-usdhc2-vmmc {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio2 19 0>; /* SD2_RESET */
+		off-on-delay-us = <12000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usdhc2_vmmc>;
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "VDD_3V3_SD";
+		startup-delay-us = <100>;
+		vin-supply = <&buck4>;
+	};
+};
+
+&A53_0 {
+	cpu-supply = <&buck2>;
+};
+
+&A53_1 {
+	cpu-supply = <&buck2>;
+};
+
+&A53_2 {
+	cpu-supply = <&buck2>;
+};
+
+&A53_3 {
+	cpu-supply = <&buck2>;
+};
+
+&ecspi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1>;
+	cs-gpios = <&gpio5 17 GPIO_ACTIVE_LOW>;
+	status = "disabled";
+};
+
+&ecspi2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi2>;
+	cs-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>;
+	status = "disabled";
+};
+
+&eqos {	/* First ethernet */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_eqos>;
+	phy-handle = <&ethphy0g>;
+	phy-mode = "rgmii-id";
+	status = "okay";
+
+	mdio {
+		compatible = "snps,dwmac-mdio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* Up to one of these two PHYs may be populated. */
+		ethphy0f: ethernet-phy@1 { /* SMSC LAN8740Ai */
+			compatible = "ethernet-phy-id0007.c110",
+				     "ethernet-phy-ieee802.3-c22";
+			interrupt-parent = <&gpio3>;
+			interrupts = <19 IRQ_TYPE_LEVEL_LOW>;
+			pinctrl-0 = <&pinctrl_ethphy0>;
+			pinctrl-names = "default";
+			reg = <1>;
+			reset-assert-us = <1000>;
+			reset-deassert-us = <1000>;
+			reset-gpios = <&gpio3 20 GPIO_ACTIVE_LOW>;
+			/* Non-default PHY population option. */
+			status = "disabled";
+		};
+
+		ethphy0g: ethernet-phy@5 { /* Micrel KSZ9131RNXI */
+			compatible = "ethernet-phy-id0022.1642",
+				     "ethernet-phy-ieee802.3-c22";
+			interrupt-parent = <&gpio3>;
+			interrupts = <19 IRQ_TYPE_LEVEL_LOW>;
+			micrel,led-mode = <0>;
+			pinctrl-0 = <&pinctrl_ethphy0>;
+			pinctrl-names = "default";
+			reg = <5>;
+			reset-assert-us = <1000>;
+			reset-deassert-us = <1000>;
+			reset-gpios = <&gpio3 20 GPIO_ACTIVE_LOW>;
+			/* Default PHY population option. */
+			status = "okay";
+		};
+	};
+};
+
+&fec {	/* Second ethernet */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_fec>;
+	phy-handle = <&ethphy1f>;
+	phy-mode = "rgmii";
+	fsl,magic-packet;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* Up to one PHY may be populated. */
+		ethphy1f: ethernet-phy@1 { /* SMSC LAN8740Ai */
+			compatible = "ethernet-phy-id0007.c110",
+				     "ethernet-phy-ieee802.3-c22";
+			interrupt-parent = <&gpio4>;
+			interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
+			pinctrl-0 = <&pinctrl_ethphy1>;
+			pinctrl-names = "default";
+			reg = <1>;
+			reset-assert-us = <1000>;
+			reset-deassert-us = <1000>;
+			reset-gpios = <&gpio4 2 GPIO_ACTIVE_LOW>;
+			/* Non-default PHY population option. */
+			status = "disabled";
+		};
+	};
+};
+
+&flexcan1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan1>;
+	status = "disabled";
+};
+
+&flexcan2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan2>;
+	status = "disabled";
+};
+
+&flexspi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexspi>;
+	status = "okay";
+
+	flash@0 {	/* W25Q128JWPIM */
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <80000000>;
+		spi-tx-bus-width = <4>;
+		spi-rx-bus-width = <4>;
+	};
+};
+
+&gpio1 {
+	gpio-line-names =
+		"DHCOM-G", "", "", "", "", "DHCOM-I", "DHCOM-J", "DHCOM-L",
+		"DHCOM-B", "DHCOM-A", "", "DHCOM-H", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "";
+};
+
+&gpio2 {
+	gpio-line-names =
+		"", "", "", "", "", "", "", "",
+		"", "", "", "DHCOM-K", "", "", "", "",
+		"", "", "", "", "DHCOM-INT", "", "", "",
+		"", "", "", "", "", "", "", "";
+};
+
+&gpio3 {
+	gpio-line-names =
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "SOM-HW0", "",
+		"", "", "", "", "", "", "SOM-MEM0", "SOM-MEM1",
+		"SOM-MEM2", "SOM-HW2", "", "", "", "", "", "";
+};
+
+&gpio4 {
+	gpio-line-names =
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "SOM-HW1", "", "", "", "",
+		"", "", "", "DHCOM-D", "", "", "", "";
+};
+
+&gpio5 {
+	gpio-line-names =
+		"", "", "DHCOM-C", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "DHCOM-E", "DHCOM-F",
+		"", "", "", "", "", "", "", "";
+};
+
+&i2c3 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	pinctrl-1 = <&pinctrl_i2c3_gpio>;
+	scl-gpios = <&gpio5 18 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio5 19 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "okay";
+
+	pmic: pmic@25 {
+		compatible = "nxp,pca9450c";
+		reg = <0x25>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_pmic>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
+		sd-vsel-gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>;
+
+		/*
+		 * i.MX 8M Plus Data Sheet for Consumer Products
+		 * 3.1.4 Operating ranges
+		 * MIMX8ML8CVNKZAB
+		 */
+		regulators {
+			buck1: BUCK1 {	/* VDD_SOC (dual-phase with BUCK3) */
+				regulator-compatible = "BUCK1";
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-ramp-delay = <3125>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			buck2: BUCK2 {	/* VDD_ARM */
+				regulator-compatible = "BUCK2";
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-ramp-delay = <3125>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			buck4: BUCK4 {	/* VDD_3V3 */
+				regulator-compatible = "BUCK4";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			buck5: BUCK5 {	/* VDD_1V8 */
+				regulator-compatible = "BUCK5";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			buck6: BUCK6 {	/* NVCC_DRAM_1V1 */
+				regulator-compatible = "BUCK6";
+				regulator-min-microvolt = <1100000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			ldo1: LDO1 {	/* NVCC_SNVS_1V8 */
+				regulator-compatible = "LDO1";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			ldo3: LDO3 {	/* VDDA_1V8 */
+				regulator-compatible = "LDO3";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+				regulator-boot-on;
+			};
+
+			ldo4: LDO4 {	/* PMIC_LDO4 */
+				regulator-compatible = "LDO4";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			ldo5: LDO5 {	/* NVCC_SD2 */
+				regulator-compatible = "LDO5";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+			};
+		};
+	};
+
+	adc@48 {
+		compatible = "ti,tla2024";
+		reg = <0x48>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		channel@0 {	/* Voltage over AIN0 and AIN1. */
+			reg = <0>;
+		};
+
+		channel@1 {	/* Voltage over AIN0 and AIN3. */
+			reg = <1>;
+		};
+
+		channel@2 {	/* Voltage over AIN1 and AIN3. */
+			reg = <2>;
+		};
+
+		channel@3 {	/* Voltage over AIN2 and AIN3. */
+			reg = <3>;
+		};
+
+		channel@4 {	/* Voltage over AIN0 and GND. */
+			reg = <4>;
+		};
+
+		channel@5 {	/* Voltage over AIN1 and GND. */
+			reg = <5>;
+		};
+
+		channel@6 {	/* Voltage over AIN2 and GND. */
+			reg = <6>;
+		};
+
+		channel@7 {	/* Voltage over AIN3 and GND. */
+			reg = <7>;
+		};
+	};
+
+	touchscreen@49 {
+		compatible = "ti,tsc2004";
+		reg = <0x49>;
+		interrupts-extended = <&gpio4 0 IRQ_TYPE_EDGE_FALLING>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_touch>;
+		vio-supply = <&buck4>;
+	};
+
+	eeprom0: eeprom@50 {	/* EEPROM with EQoS MAC address */
+		compatible = "atmel,24c02";
+		pagesize = <16>;
+		reg = <0x50>;
+	};
+
+	rv3032: rtc@51 {
+		compatible = "microcrystal,rv3032";
+		reg = <0x51>;
+		interrupts-extended = <&gpio5 5 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_rtc>;
+	};
+
+	eeprom1: eeprom@53 {	/* EEPROM with FEC MAC address */
+		compatible = "atmel,24c02";
+		pagesize = <16>;
+		reg = <0x53>;
+	};
+};
+
+&i2c4 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c4>;
+	pinctrl-1 = <&pinctrl_i2c4_gpio>;
+	scl-gpios = <&gpio5 20 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio5 21 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "okay";
+};
+
+&i2c5 {	/* HDMI EDID bus */
+	clock-frequency = <100000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c5>;
+	pinctrl-1 = <&pinctrl_i2c5_gpio>;
+	scl-gpios = <&gpio3 26 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio3 27 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "okay";
+};
+
+&pwm1 {
+	pinctrl-0 = <&pinctrl_pwm1>;
+	pinctrl-names = "default";
+	status = "disabled";
+};
+
+&uart1 {
+	/* CA53 console */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&uart2 {
+	/* Bluetooth */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+	status = "okay";
+};
+
+&usb3_phy0 {
+	status = "okay";
+};
+
+&usb3_0 {
+	status = "okay";
+};
+
+&usb_dwc3_0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb0_vbus>;
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&usb3_phy1 {
+	status = "okay";
+};
+
+&usb3_1 {
+	status = "okay";
+};
+
+&usb_dwc3_1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb1_vbus>;
+	dr_mode = "host";
+	status = "okay";
+};
+
+/* SDIO WiFi */
+&usdhc1 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
+	vmmc-supply = <&buck4>;
+	bus-width = <4>;
+	non-removable;
+	cap-power-off-card;
+	keep-power-in-suspend;
+	status = "okay";
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	brcmf: bcrmf@1 {	/* muRata 2AE */
+		reg = <1>;
+		compatible = "cypress,cyw4373-fmac", "brcm,bcm4329-fmac";
+		/*
+		 * The "host-wake" interrupt output is by default not
+		 * connected to the SoC, but can be connected on to
+		 * SoC pin on the carrier board.
+		 */
+		reset-gpios = <&gpio1 13 GPIO_ACTIVE_LOW>;
+	};
+};
+
+/* SD slot */
+&usdhc2 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
+	cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
+	vmmc-supply = <&reg_usdhc2_vmmc>;
+	bus-width = <4>;
+	status = "okay";
+};
+
+/* eMMC */
+&usdhc3 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+	vmmc-supply = <&buck4>;
+	vqmmc-supply = <&buck5>;
+	bus-width = <8>;
+	non-removable;
+	status = "okay";
+};
+
+&wdog1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog>;
+	fsl,ext-reset-output;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl-0 = <&pinctrl_hog_base
+		     &pinctrl_dhcom_a &pinctrl_dhcom_b &pinctrl_dhcom_c
+		     &pinctrl_dhcom_d &pinctrl_dhcom_e &pinctrl_dhcom_f
+		     &pinctrl_dhcom_g &pinctrl_dhcom_h &pinctrl_dhcom_i
+		     &pinctrl_dhcom_j &pinctrl_dhcom_k &pinctrl_dhcom_l
+		     /* GPIO_M is connected to CLKOUT2 */
+		     &pinctrl_dhcom_int>;
+	pinctrl-names = "default";
+
+	pinctrl_dhcom_a: dhcom-a-grp {
+		fsl,pins = <
+			/* ENET_QOS_EVENT0-OUT */
+			MX8MP_IOMUXC_GPIO1_IO09__GPIO1_IO09		0x2
+		>;
+	};
+
+	pinctrl_dhcom_b: dhcom-b-grp {
+		fsl,pins = <
+			/* ENET_QOS_EVENT0-IN */
+			MX8MP_IOMUXC_GPIO1_IO08__GPIO1_IO08		0x2
+		>;
+	};
+
+	pinctrl_dhcom_c: dhcom-c-grp {
+		fsl,pins = <
+			/* GPIO_C */
+			MX8MP_IOMUXC_SAI3_MCLK__GPIO5_IO02		0x2
+		>;
+	};
+
+	pinctrl_dhcom_d: dhcom-d-grp {
+		fsl,pins = <
+			/* GPIO_D */
+			MX8MP_IOMUXC_SAI2_MCLK__GPIO4_IO27		0x2
+		>;
+	};
+
+	pinctrl_dhcom_e: dhcom-e-grp {
+		fsl,pins = <
+			/* GPIO_E */
+			MX8MP_IOMUXC_UART1_RXD__GPIO5_IO22		0x2
+		>;
+	};
+
+	pinctrl_dhcom_f: dhcom-f-grp {
+		fsl,pins = <
+			/* GPIO_F */
+			MX8MP_IOMUXC_UART1_TXD__GPIO5_IO23		0x2
+		>;
+	};
+
+	pinctrl_dhcom_g: dhcom-g-grp {
+		fsl,pins = <
+			/* GPIO_G */
+			MX8MP_IOMUXC_GPIO1_IO00__GPIO1_IO00		0x2
+		>;
+	};
+
+	pinctrl_dhcom_h: dhcom-h-grp {
+		fsl,pins = <
+			/* GPIO_H */
+			MX8MP_IOMUXC_GPIO1_IO11__GPIO1_IO11		0x2
+		>;
+	};
+
+	pinctrl_dhcom_i: dhcom-i-grp {
+		fsl,pins = <
+			/* CSI1_SYNC */
+			MX8MP_IOMUXC_GPIO1_IO05__GPIO1_IO05		0x2
+		>;
+	};
+
+	pinctrl_dhcom_j: dhcom-j-grp {
+		fsl,pins = <
+			/* CSIx_#RST */
+			MX8MP_IOMUXC_GPIO1_IO06__GPIO1_IO06		0x2
+		>;
+	};
+
+	pinctrl_dhcom_k: dhcom-k-grp {
+		fsl,pins = <
+			/* CSIx_PWDN */
+			MX8MP_IOMUXC_SD1_STROBE__GPIO2_IO11		0x2
+		>;
+	};
+
+	pinctrl_dhcom_l: dhcom-l-grp {
+		fsl,pins = <
+			/* CSI2_SYNC */
+			MX8MP_IOMUXC_GPIO1_IO07__GPIO1_IO07		0x2
+		>;
+	};
+
+	pinctrl_dhcom_int: dhcom-int-grp {
+		fsl,pins = <
+			/* INT_HIGHEST_PRIO */
+			MX8MP_IOMUXC_SD2_WP__GPIO2_IO20			0x2
+		>;
+	};
+
+	pinctrl_hog_base: dhcom-hog-base-grp {
+		fsl,pins = <
+			/* GPIOs for memory coding */
+			MX8MP_IOMUXC_SAI5_RXD1__GPIO3_IO22		0x40000080
+			MX8MP_IOMUXC_SAI5_RXD2__GPIO3_IO23		0x40000080
+			MX8MP_IOMUXC_SAI5_RXD3__GPIO3_IO24		0x40000080
+			/* GPIOs for hardware coding */
+			MX8MP_IOMUXC_NAND_DQS__GPIO3_IO14		0x40000080
+			MX8MP_IOMUXC_SAI1_TXD7__GPIO4_IO19		0x40000080
+			MX8MP_IOMUXC_SAI5_MCLK__GPIO3_IO25		0x40000080
+		>;
+	};
+
+	pinctrl_ecspi1: dhcom-ecspi1-grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_I2C1_SCL__ECSPI1_SCLK		0x44
+			MX8MP_IOMUXC_I2C1_SDA__ECSPI1_MOSI		0x44
+			MX8MP_IOMUXC_I2C2_SCL__ECSPI1_MISO		0x44
+			MX8MP_IOMUXC_I2C2_SDA__GPIO5_IO17		0x40
+		>;
+	};
+
+	pinctrl_ecspi2: dhcom-ecspi2-grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_ECSPI2_SCLK__ECSPI2_SCLK		0x44
+			MX8MP_IOMUXC_ECSPI2_MOSI__ECSPI2_MOSI		0x44
+			MX8MP_IOMUXC_ECSPI2_MISO__ECSPI2_MISO		0x44
+			MX8MP_IOMUXC_ECSPI2_SS0__GPIO5_IO13		0x40
+		>;
+	};
+
+	pinctrl_eqos: dhcom-eqos-grp {	/* RGMII */
+		fsl,pins = <
+			MX8MP_IOMUXC_ENET_MDC__ENET_QOS_MDC		0x3
+			MX8MP_IOMUXC_ENET_MDIO__ENET_QOS_MDIO		0x3
+			MX8MP_IOMUXC_ENET_TX_CTL__ENET_QOS_RGMII_TX_CTL	0x1f
+			MX8MP_IOMUXC_ENET_TXC__CCM_ENET_QOS_CLOCK_GENERATE_TX_CLK	0x1f
+			MX8MP_IOMUXC_ENET_TD0__ENET_QOS_RGMII_TD0	0x1f
+			MX8MP_IOMUXC_ENET_TD1__ENET_QOS_RGMII_TD1	0x1f
+			MX8MP_IOMUXC_ENET_TD2__ENET_QOS_RGMII_TD2	0x1f
+			MX8MP_IOMUXC_ENET_TD3__ENET_QOS_RGMII_TD3	0x1f
+			MX8MP_IOMUXC_ENET_RXC__CCM_ENET_QOS_CLOCK_GENERATE_RX_CLK	0x91
+			MX8MP_IOMUXC_ENET_RX_CTL__ENET_QOS_RGMII_RX_CTL	0x91
+			MX8MP_IOMUXC_ENET_RD0__ENET_QOS_RGMII_RD0	0x91
+			MX8MP_IOMUXC_ENET_RD1__ENET_QOS_RGMII_RD1	0x91
+			MX8MP_IOMUXC_ENET_RD2__ENET_QOS_RGMII_RD2	0x91
+			MX8MP_IOMUXC_ENET_RD3__ENET_QOS_RGMII_RD3	0x91
+		>;
+	};
+
+	pinctrl_enet_vio: dhcom-enet-vio-grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SD1_RESET_B__GPIO2_IO10		0x22
+		>;
+	};
+
+	pinctrl_ethphy0: dhcom-ethphy0-grp {
+		fsl,pins = <
+			/* ENET1_#RST Reset */
+			MX8MP_IOMUXC_SAI5_RXC__GPIO3_IO20		0x22
+			/* ENET1_#INT Interrupt */
+			MX8MP_IOMUXC_SAI5_RXFS__GPIO3_IO19		0x22
+		>;
+	};
+
+	pinctrl_ethphy1: dhcom-ethphy1-grp {
+		fsl,pins = <
+			/* ENET1_#RST Reset */
+			MX8MP_IOMUXC_SAI1_RXD0__GPIO4_IO02		0x11
+			/* ENET1_#INT Interrupt */
+			MX8MP_IOMUXC_SAI1_RXD1__GPIO4_IO03		0x11
+		>;
+	};
+
+	pinctrl_fec: dhcom-fec-grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SAI1_MCLK__ENET1_TX_CLK		0x1f
+			MX8MP_IOMUXC_SAI1_RXD2__ENET1_MDC		0x3
+			MX8MP_IOMUXC_SAI1_RXD3__ENET1_MDIO		0x3
+			MX8MP_IOMUXC_SAI1_RXD4__ENET1_RGMII_RD0		0x91
+			MX8MP_IOMUXC_SAI1_RXD5__ENET1_RGMII_RD1		0x91
+			MX8MP_IOMUXC_SAI1_RXD6__ENET1_RGMII_RD2		0x91
+			MX8MP_IOMUXC_SAI1_RXD7__ENET1_RGMII_RD3		0x91
+			MX8MP_IOMUXC_SAI1_TXC__ENET1_RGMII_RXC		0x91
+			MX8MP_IOMUXC_SAI1_TXFS__ENET1_RGMII_RX_CTL	0x91
+			MX8MP_IOMUXC_SAI1_TXD0__ENET1_RGMII_TD0		0x1f
+			MX8MP_IOMUXC_SAI1_TXD1__ENET1_RGMII_TD1		0x1f
+			MX8MP_IOMUXC_SAI1_TXD2__ENET1_RGMII_TD2		0x1f
+			MX8MP_IOMUXC_SAI1_TXD3__ENET1_RGMII_TD3		0x1f
+			MX8MP_IOMUXC_SAI1_TXD4__ENET1_RGMII_TX_CTL	0x1f
+			MX8MP_IOMUXC_SAI1_TXD5__ENET1_RGMII_TXC		0x1f
+			MX8MP_IOMUXC_SAI1_TXD6__ENET1_RX_ER		0x1f
+		>;
+	};
+
+	pinctrl_flexcan1: dhcom-flexcan1-grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SPDIF_RX__CAN1_RX			0x154
+			MX8MP_IOMUXC_SPDIF_TX__CAN1_TX			0x154
+		>;
+	};
+
+	pinctrl_flexcan2: dhcom-flexcan2-grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_UART3_RXD__CAN2_TX			0x154
+			MX8MP_IOMUXC_UART3_TXD__CAN2_RX			0x154
+		>;
+	};
+
+	pinctrl_flexspi: dhcom-flexspi-grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_NAND_ALE__FLEXSPI_A_SCLK		0x1c2
+			MX8MP_IOMUXC_NAND_CE0_B__FLEXSPI_A_SS0_B	0x82
+			MX8MP_IOMUXC_NAND_DATA00__FLEXSPI_A_DATA00	0x82
+			MX8MP_IOMUXC_NAND_DATA01__FLEXSPI_A_DATA01	0x82
+			MX8MP_IOMUXC_NAND_DATA02__FLEXSPI_A_DATA02	0x82
+			MX8MP_IOMUXC_NAND_DATA03__FLEXSPI_A_DATA03	0x82
+		>;
+	};
+
+	pinctrl_hdmi: dhcom-hdmi-grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_HDMI_CEC__HDMIMIX_HDMI_CEC		0x154
+			MX8MP_IOMUXC_HDMI_HPD__HDMIMIX_HDMI_HPD		0x154
+		>;
+	};
+
+	pinctrl_i2c3: dhcom-i2c3-grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_I2C3_SCL__I2C3_SCL			0x40000084
+			MX8MP_IOMUXC_I2C3_SDA__I2C3_SDA			0x40000084
+		>;
+	};
+
+	pinctrl_i2c3_gpio: dhcom-i2c3-gpio-grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_I2C3_SCL__GPIO5_IO18		0x84
+			MX8MP_IOMUXC_I2C3_SDA__GPIO5_IO19		0x84
+		>;
+	};
+
+	pinctrl_i2c4: dhcom-i2c4-grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_I2C4_SCL__I2C4_SCL			0x40000084
+			MX8MP_IOMUXC_I2C4_SDA__I2C4_SDA			0x40000084
+		>;
+	};
+
+	pinctrl_i2c4_gpio: dhcom-i2c4-gpio-grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_I2C4_SCL__GPIO5_IO20		0x84
+			MX8MP_IOMUXC_I2C4_SDA__GPIO5_IO21		0x84
+		>;
+	};
+
+	pinctrl_i2c5: dhcom-i2c5-grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_HDMI_DDC_SCL__I2C5_SCL		0x40000084
+			MX8MP_IOMUXC_HDMI_DDC_SDA__I2C5_SDA		0x40000084
+		>;
+	};
+
+	pinctrl_i2c5_gpio: dhcom-i2c5-gpio-grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_HDMI_DDC_SCL__GPIO3_IO26		0x84
+			MX8MP_IOMUXC_HDMI_DDC_SDA__GPIO3_IO27		0x84
+		>;
+	};
+
+	pinctrl_pmic: dhcom-pmic-grp {
+		fsl,pins = <
+			/* PMIC_nINT */
+			MX8MP_IOMUXC_GPIO1_IO03__GPIO1_IO03		0x40000090
+		>;
+	};
+
+	pinctrl_pwm1: dhcom-pwm1-grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_GPIO1_IO01__PWM1_OUT		0x6
+		>;
+	};
+
+	pinctrl_rtc: dhcom-rtc-grp {
+		fsl,pins = <
+			/* RTC_#INT Interrupt */
+			MX8MP_IOMUXC_SPDIF_EXT_CLK__GPIO5_IO05		0x40000080
+		>;
+	};
+
+	pinctrl_touch: dhcom-touch-grp {
+		fsl,pins = <
+			/* #TOUCH_INT */
+			MX8MP_IOMUXC_SAI1_RXFS__GPIO4_IO00		0x40000080
+		>;
+	};
+
+	pinctrl_uart1: dhcom-uart1-grp {
+		fsl,pins = <
+			/* Console UART */
+			MX8MP_IOMUXC_SAI2_RXC__UART1_DCE_RX		0x49
+			MX8MP_IOMUXC_SAI2_RXFS__UART1_DCE_TX		0x49
+			MX8MP_IOMUXC_SAI2_RXD0__UART1_DCE_RTS		0x49
+			MX8MP_IOMUXC_SAI2_TXFS__UART1_DCE_CTS		0x49
+		>;
+	};
+
+	pinctrl_uart2: dhcom-uart2-grp {
+		fsl,pins = <
+			/* Bluetooth UART */
+			MX8MP_IOMUXC_UART2_RXD__UART2_DCE_RX		0x49
+			MX8MP_IOMUXC_UART2_TXD__UART2_DCE_TX		0x49
+			MX8MP_IOMUXC_SD1_DATA4__UART2_DCE_RTS		0x49
+			MX8MP_IOMUXC_SD1_DATA5__UART2_DCE_CTS		0x49
+		>;
+	};
+
+	pinctrl_uart3: dhcom-uart3-grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_ECSPI1_SCLK__UART3_DCE_RX		0x49
+			MX8MP_IOMUXC_ECSPI1_MOSI__UART3_DCE_TX		0x49
+			MX8MP_IOMUXC_ECSPI1_SS0__UART3_DCE_RTS		0x49
+			MX8MP_IOMUXC_ECSPI1_MISO__UART3_DCE_CTS		0x49
+		>;
+	};
+
+	pinctrl_uart4: dhcom-uart4-grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_UART4_RXD__UART4_DCE_RX		0x49
+			MX8MP_IOMUXC_UART4_TXD__UART4_DCE_TX		0x49
+		>;
+	};
+
+	pinctrl_usb0_vbus: dhcom-usb0-grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_GPIO1_IO10__USB1_OTG_ID		0x0
+		>;
+	};
+
+	pinctrl_usb1_vbus: dhcom-usb1-grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_GPIO1_IO14__USB2_OTG_PWR		0x6
+			MX8MP_IOMUXC_GPIO1_IO15__USB2_OTG_OC		0x80
+		>;
+	};
+
+	pinctrl_usdhc1: dhcom-usdhc1-grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SD1_CLK__USDHC1_CLK		0x190
+			MX8MP_IOMUXC_SD1_CMD__USDHC1_CMD		0x1d0
+			MX8MP_IOMUXC_SD1_DATA0__USDHC1_DATA0		0x1d0
+			MX8MP_IOMUXC_SD1_DATA1__USDHC1_DATA1		0x1d0
+			MX8MP_IOMUXC_SD1_DATA2__USDHC1_DATA2		0x1d0
+			MX8MP_IOMUXC_SD1_DATA3__USDHC1_DATA3		0x1d0
+			/* BT_REG_EN */
+			MX8MP_IOMUXC_GPIO1_IO12__GPIO1_IO12		0x144
+			/* WL_REG_EN */
+			MX8MP_IOMUXC_GPIO1_IO13__GPIO1_IO13		0x144
+		>;
+	};
+
+	pinctrl_usdhc1_100mhz: dhcom-usdhc1-100mhz-grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SD1_CLK__USDHC1_CLK		0x194
+			MX8MP_IOMUXC_SD1_CMD__USDHC1_CMD		0x1d4
+			MX8MP_IOMUXC_SD1_DATA0__USDHC1_DATA0		0x1d4
+			MX8MP_IOMUXC_SD1_DATA1__USDHC1_DATA1		0x1d4
+			MX8MP_IOMUXC_SD1_DATA2__USDHC1_DATA2		0x1d4
+			MX8MP_IOMUXC_SD1_DATA3__USDHC1_DATA3		0x1d4
+			/* BT_REG_EN */
+			MX8MP_IOMUXC_GPIO1_IO12__GPIO1_IO12		0x144
+			/* WL_REG_EN */
+			MX8MP_IOMUXC_GPIO1_IO13__GPIO1_IO13		0x144
+		>;
+	};
+
+	pinctrl_usdhc1_200mhz: dhcom-usdhc1-200mhz-grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SD1_CLK__USDHC1_CLK		0x196
+			MX8MP_IOMUXC_SD1_CMD__USDHC1_CMD		0x1d6
+			MX8MP_IOMUXC_SD1_DATA0__USDHC1_DATA0		0x1d6
+			MX8MP_IOMUXC_SD1_DATA1__USDHC1_DATA1		0x1d6
+			MX8MP_IOMUXC_SD1_DATA2__USDHC1_DATA2		0x1d6
+			MX8MP_IOMUXC_SD1_DATA3__USDHC1_DATA3		0x1d6
+			/* BT_REG_EN */
+			MX8MP_IOMUXC_GPIO1_IO12__GPIO1_IO12		0x144
+			/* WL_REG_EN */
+			MX8MP_IOMUXC_GPIO1_IO13__GPIO1_IO13		0x144
+		>;
+	};
+
+	pinctrl_usdhc2: dhcom-usdhc2-grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK		0x190
+			MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD		0x1d0
+			MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0		0x1d0
+			MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1		0x1d0
+			MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2		0x1d0
+			MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3		0x1d0
+			MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT		0xc1
+		>;
+	};
+
+	pinctrl_usdhc2_100mhz: dhcom-usdhc2-100mhz-grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK		0x194
+			MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD		0x1d4
+			MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0		0x1d4
+			MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1		0x1d4
+			MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2		0x1d4
+			MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3		0x1d4
+			MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT		0xc1
+		>;
+	};
+
+	pinctrl_usdhc2_200mhz: dhcom-usdhc2-200mhz-grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK		0x196
+			MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD		0x1d6
+			MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0		0x1d6
+			MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1		0x1d6
+			MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2		0x1d6
+			MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3		0x1d6
+			MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT		0xc1
+		>;
+	};
+
+	pinctrl_usdhc2_vmmc: dhcom-usdhc2-vmmc-grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SD2_RESET_B__GPIO2_IO19		0x20
+		>;
+	};
+
+	pinctrl_usdhc2_gpio: dhcom-usdhc2-gpio-grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SD2_CD_B__GPIO2_IO12		0x40000080
+		>;
+	};
+
+	pinctrl_usdhc3: dhcom-usdhc3-grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK		0x190
+			MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD		0x1d0
+			MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0		0x1d0
+			MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1		0x1d0
+			MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2		0x1d0
+			MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3		0x1d0
+			MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4		0x1d0
+			MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5		0x1d0
+			MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6		0x1d0
+			MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7		0x1d0
+			MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE		0x190
+			MX8MP_IOMUXC_NAND_READY_B__USDHC3_RESET_B	0x141
+		>;
+	};
+
+	pinctrl_usdhc3_100mhz: dhcom-usdhc3-100mhz-grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK		0x194
+			MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD		0x1d4
+			MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0		0x1d4
+			MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1		0x1d4
+			MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2		0x1d4
+			MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3		0x1d4
+			MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4		0x1d4
+			MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5		0x1d4
+			MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6		0x1d4
+			MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7		0x1d4
+			MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE		0x194
+			MX8MP_IOMUXC_NAND_READY_B__USDHC3_RESET_B	0x141
+		>;
+	};
+
+	pinctrl_usdhc3_200mhz: dhcom-usdhc3-200mhz-grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK		0x196
+			MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD		0x1d6
+			MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0		0x1d6
+			MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1		0x1d6
+			MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2		0x1d6
+			MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3		0x1d6
+			MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4		0x1d6
+			MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5		0x1d6
+			MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6		0x1d6
+			MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7		0x1d6
+			MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE		0x196
+			MX8MP_IOMUXC_NAND_READY_B__USDHC3_RESET_B	0x141
+		>;
+	};
+
+	pinctrl_wdog: dhcom-wdog-grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_GPIO1_IO02__WDOG1_WDOG_B		0xc6
+		>;
+	};
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mp-evk.dts b/arch/arm64/boot/dts/freescale/imx8mp-evk.dts
index 7b99fad6e4d6..9f1469db554d 100644
--- a/arch/arm64/boot/dts/freescale/imx8mp-evk.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mp-evk.dts
@@ -5,6 +5,7 @@
 
 /dts-v1/;
 
+#include <dt-bindings/phy/phy-imx8-pcie.h>
 #include "imx8mp.dtsi"
 
 / {
@@ -33,6 +34,12 @@
 		      <0x1 0x00000000 0 0xc0000000>;
 	};
 
+	pcie0_refclk: pcie0-refclk {
+		compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <100000000>;
+	};
+
 	reg_can1_stby: regulator-can1-stby {
 		compatible = "regulator-fixed";
 		regulator-name = "can1-stby";
@@ -55,6 +62,17 @@
 		enable-active-high;
 	};
 
+	reg_pcie0: regulator-pcie {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_pcie0_reg>;
+		regulator-name = "MPCIE_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio2 6 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
 	reg_usdhc2_vmmc: regulator-usdhc2 {
 		compatible = "regulator-fixed";
 		pinctrl-names = "default";
@@ -67,18 +85,20 @@
 	};
 };
 
-&flexcan1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_flexcan1>;
-	xceiver-supply = <&reg_can1_stby>;
-	status = "okay";
+&A53_0 {
+	cpu-supply = <&reg_arm>;
 };
 
-&flexcan2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_flexcan2>;
-	xceiver-supply = <&reg_can2_stby>;
-	status = "disabled";/* can2 pin conflict with pdm */
+&A53_1 {
+	cpu-supply = <&reg_arm>;
+};
+
+&A53_2 {
+	cpu-supply = <&reg_arm>;
+};
+
+&A53_3 {
+	cpu-supply = <&reg_arm>;
 };
 
 &eqos {
@@ -86,6 +106,9 @@
 	pinctrl-0 = <&pinctrl_eqos>;
 	phy-mode = "rgmii-id";
 	phy-handle = <&ethphy0>;
+	snps,force_thresh_dma_mode;
+	snps,mtl-tx-config = <&mtl_tx_setup>;
+	snps,mtl-rx-config = <&mtl_rx_setup>;
 	status = "okay";
 
 	mdio {
@@ -97,6 +120,75 @@
 			compatible = "ethernet-phy-ieee802.3-c22";
 			reg = <1>;
 			eee-broken-1000t;
+			reset-gpios = <&gpio4 22 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <10000>;
+			reset-deassert-us = <80000>;
+			realtek,clkout-disable;
+		};
+	};
+
+	mtl_tx_setup: tx-queues-config {
+		snps,tx-queues-to-use = <5>;
+		snps,tx-sched-sp;
+
+		queue0 {
+			snps,dcb-algorithm;
+			snps,priority = <0x1>;
+		};
+
+		queue1 {
+			snps,dcb-algorithm;
+			snps,priority = <0x2>;
+		};
+
+		queue2 {
+			snps,dcb-algorithm;
+			snps,priority = <0x4>;
+		};
+
+		queue3 {
+			snps,dcb-algorithm;
+			snps,priority = <0x8>;
+		};
+
+		queue4 {
+			snps,dcb-algorithm;
+			snps,priority = <0xf0>;
+		};
+	};
+
+	mtl_rx_setup: rx-queues-config {
+		snps,rx-queues-to-use = <5>;
+		snps,rx-sched-sp;
+
+		queue0 {
+			snps,dcb-algorithm;
+			snps,priority = <0x1>;
+			snps,map-to-dma-channel = <0>;
+		};
+
+		queue1 {
+			snps,dcb-algorithm;
+			snps,priority = <0x2>;
+			snps,map-to-dma-channel = <1>;
+		};
+
+		queue2 {
+			snps,dcb-algorithm;
+			snps,priority = <0x4>;
+			snps,map-to-dma-channel = <2>;
+		};
+
+		queue3 {
+			snps,dcb-algorithm;
+			snps,priority = <0x8>;
+			snps,map-to-dma-channel = <3>;
+		};
+
+		queue4 {
+			snps,dcb-algorithm;
+			snps,priority = <0xf0>;
+			snps,map-to-dma-channel = <4>;
 		};
 	};
 };
@@ -120,10 +212,25 @@
 			reset-gpios = <&gpio4 2 GPIO_ACTIVE_LOW>;
 			reset-assert-us = <10000>;
 			reset-deassert-us = <80000>;
+			realtek,clkout-disable;
 		};
 	};
 };
 
+&flexcan1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan1>;
+	xceiver-supply = <&reg_can1_stby>;
+	status = "okay";
+};
+
+&flexcan2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan2>;
+	xceiver-supply = <&reg_can2_stby>;
+	status = "disabled";/* can2 pin conflict with pdm */
+};
+
 &i2c1 {
 	clock-frequency = <400000>;
 	pinctrl-names = "default";
@@ -148,7 +255,7 @@
 				regulator-ramp-delay = <3125>;
 			};
 
-			BUCK2 {
+			reg_arm: BUCK2 {
 				regulator-name = "BUCK2";
 				regulator-min-microvolt = <720000>;
 				regulator-max-microvolt = <1025000>;
@@ -221,9 +328,68 @@
 		reg = <0x20>;
 		gpio-controller;
 		#gpio-cells = <2>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_pca6416_int>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <12 IRQ_TYPE_LEVEL_LOW>;
+		gpio-line-names = "EXT_PWREN1",
+			"EXT_PWREN2",
+			"CAN1/I2C5_SEL",
+			"PDM/CAN2_SEL",
+			"FAN_EN",
+			"PWR_MEAS_IO1",
+			"PWR_MEAS_IO2",
+			"EXP_P0_7",
+			"EXP_P1_0",
+			"EXP_P1_1",
+			"EXP_P1_2",
+			"EXP_P1_3",
+			"EXP_P1_4",
+			"EXP_P1_5",
+			"EXP_P1_6",
+			"EXP_P1_7";
 	};
 };
 
+/* I2C on expansion connector J22. */
+&i2c5 {
+	clock-frequency = <100000>; /* Lower clock speed for external bus. */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c5>;
+	status = "disabled"; /* can1 pins conflict with i2c5 */
+
+	/* GPIO 2 of PCA6416 is used to switch between CAN1 and I2C5 functions:
+	 *     LOW:  CAN1 (default, pull-down)
+	 *     HIGH: I2C5
+	 * You need to set it to high to enable I2C5 (for example, add gpio-hog
+	 * in pca6416 node).
+	 */
+};
+
+&pcie_phy {
+	fsl,refclk-pad-mode = <IMX8_PCIE_REFCLK_PAD_INPUT>;
+	clocks = <&pcie0_refclk>;
+	clock-names = "ref";
+	status = "okay";
+};
+
+&pcie {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pcie0>;
+	reset-gpio = <&gpio2 7 GPIO_ACTIVE_LOW>;
+	clocks = <&clk IMX8MP_CLK_HSIO_ROOT>,
+		 <&clk IMX8MP_CLK_PCIE_ROOT>,
+		 <&clk IMX8MP_CLK_HSIO_AXI>;
+	clock-names = "pcie", "pcie_aux", "pcie_bus";
+	assigned-clocks = <&clk IMX8MP_CLK_PCIE_AUX>;
+	assigned-clock-rates = <10000000>;
+	assigned-clock-parents = <&clk IMX8MP_SYS_PLL2_50M>;
+	vpcie-supply = <&reg_pcie0>;
+	status = "okay";
+};
+
 &snvs_pwrkey {
 	status = "okay";
 };
@@ -285,41 +451,41 @@
 &iomuxc {
 	pinctrl_eqos: eqosgrp {
 		fsl,pins = <
-			MX8MP_IOMUXC_ENET_MDC__ENET_QOS_MDC				0x3
-			MX8MP_IOMUXC_ENET_MDIO__ENET_QOS_MDIO				0x3
-			MX8MP_IOMUXC_ENET_RD0__ENET_QOS_RGMII_RD0			0x91
-			MX8MP_IOMUXC_ENET_RD1__ENET_QOS_RGMII_RD1			0x91
-			MX8MP_IOMUXC_ENET_RD2__ENET_QOS_RGMII_RD2			0x91
-			MX8MP_IOMUXC_ENET_RD3__ENET_QOS_RGMII_RD3			0x91
-			MX8MP_IOMUXC_ENET_RXC__CCM_ENET_QOS_CLOCK_GENERATE_RX_CLK	0x91
-			MX8MP_IOMUXC_ENET_RX_CTL__ENET_QOS_RGMII_RX_CTL			0x91
-			MX8MP_IOMUXC_ENET_TD0__ENET_QOS_RGMII_TD0			0x1f
-			MX8MP_IOMUXC_ENET_TD1__ENET_QOS_RGMII_TD1			0x1f
-			MX8MP_IOMUXC_ENET_TD2__ENET_QOS_RGMII_TD2			0x1f
-			MX8MP_IOMUXC_ENET_TD3__ENET_QOS_RGMII_TD3			0x1f
-			MX8MP_IOMUXC_ENET_TX_CTL__ENET_QOS_RGMII_TX_CTL			0x1f
-			MX8MP_IOMUXC_ENET_TXC__CCM_ENET_QOS_CLOCK_GENERATE_TX_CLK	0x1f
-			MX8MP_IOMUXC_SAI2_RXC__GPIO4_IO22				0x19
+			MX8MP_IOMUXC_ENET_MDC__ENET_QOS_MDC				0x2
+			MX8MP_IOMUXC_ENET_MDIO__ENET_QOS_MDIO				0x2
+			MX8MP_IOMUXC_ENET_RD0__ENET_QOS_RGMII_RD0			0x90
+			MX8MP_IOMUXC_ENET_RD1__ENET_QOS_RGMII_RD1			0x90
+			MX8MP_IOMUXC_ENET_RD2__ENET_QOS_RGMII_RD2			0x90
+			MX8MP_IOMUXC_ENET_RD3__ENET_QOS_RGMII_RD3			0x90
+			MX8MP_IOMUXC_ENET_RXC__CCM_ENET_QOS_CLOCK_GENERATE_RX_CLK	0x90
+			MX8MP_IOMUXC_ENET_RX_CTL__ENET_QOS_RGMII_RX_CTL			0x90
+			MX8MP_IOMUXC_ENET_TD0__ENET_QOS_RGMII_TD0			0x16
+			MX8MP_IOMUXC_ENET_TD1__ENET_QOS_RGMII_TD1			0x16
+			MX8MP_IOMUXC_ENET_TD2__ENET_QOS_RGMII_TD2			0x16
+			MX8MP_IOMUXC_ENET_TD3__ENET_QOS_RGMII_TD3			0x16
+			MX8MP_IOMUXC_ENET_TX_CTL__ENET_QOS_RGMII_TX_CTL			0x16
+			MX8MP_IOMUXC_ENET_TXC__CCM_ENET_QOS_CLOCK_GENERATE_TX_CLK	0x16
+			MX8MP_IOMUXC_SAI2_RXC__GPIO4_IO22				0x10
 		>;
 	};
 
 	pinctrl_fec: fecgrp {
 		fsl,pins = <
-			MX8MP_IOMUXC_SAI1_RXD2__ENET1_MDC		0x3
-			MX8MP_IOMUXC_SAI1_RXD3__ENET1_MDIO		0x3
-			MX8MP_IOMUXC_SAI1_RXD4__ENET1_RGMII_RD0		0x91
-			MX8MP_IOMUXC_SAI1_RXD5__ENET1_RGMII_RD1		0x91
-			MX8MP_IOMUXC_SAI1_RXD6__ENET1_RGMII_RD2		0x91
-			MX8MP_IOMUXC_SAI1_RXD7__ENET1_RGMII_RD3		0x91
-			MX8MP_IOMUXC_SAI1_TXC__ENET1_RGMII_RXC		0x91
-			MX8MP_IOMUXC_SAI1_TXFS__ENET1_RGMII_RX_CTL	0x91
-			MX8MP_IOMUXC_SAI1_TXD0__ENET1_RGMII_TD0		0x1f
-			MX8MP_IOMUXC_SAI1_TXD1__ENET1_RGMII_TD1		0x1f
-			MX8MP_IOMUXC_SAI1_TXD2__ENET1_RGMII_TD2		0x1f
-			MX8MP_IOMUXC_SAI1_TXD3__ENET1_RGMII_TD3		0x1f
-			MX8MP_IOMUXC_SAI1_TXD4__ENET1_RGMII_TX_CTL	0x1f
-			MX8MP_IOMUXC_SAI1_TXD5__ENET1_RGMII_TXC		0x1f
-			MX8MP_IOMUXC_SAI1_RXD0__GPIO4_IO02		0x19
+			MX8MP_IOMUXC_SAI1_RXD2__ENET1_MDC		0x2
+			MX8MP_IOMUXC_SAI1_RXD3__ENET1_MDIO		0x2
+			MX8MP_IOMUXC_SAI1_RXD4__ENET1_RGMII_RD0		0x90
+			MX8MP_IOMUXC_SAI1_RXD5__ENET1_RGMII_RD1		0x90
+			MX8MP_IOMUXC_SAI1_RXD6__ENET1_RGMII_RD2		0x90
+			MX8MP_IOMUXC_SAI1_RXD7__ENET1_RGMII_RD3		0x90
+			MX8MP_IOMUXC_SAI1_TXC__ENET1_RGMII_RXC		0x90
+			MX8MP_IOMUXC_SAI1_TXFS__ENET1_RGMII_RX_CTL	0x90
+			MX8MP_IOMUXC_SAI1_TXD0__ENET1_RGMII_TD0		0x16
+			MX8MP_IOMUXC_SAI1_TXD1__ENET1_RGMII_TD1		0x16
+			MX8MP_IOMUXC_SAI1_TXD2__ENET1_RGMII_TD2		0x16
+			MX8MP_IOMUXC_SAI1_TXD3__ENET1_RGMII_TD3		0x16
+			MX8MP_IOMUXC_SAI1_TXD4__ENET1_RGMII_TX_CTL	0x16
+			MX8MP_IOMUXC_SAI1_TXD5__ENET1_RGMII_TXC		0x16
+			MX8MP_IOMUXC_SAI1_RXD0__GPIO4_IO02		0x10
 		>;
 	};
 
@@ -351,21 +517,41 @@
 
 	pinctrl_gpio_led: gpioledgrp {
 		fsl,pins = <
-			MX8MP_IOMUXC_NAND_READY_B__GPIO3_IO16	0x19
+			MX8MP_IOMUXC_NAND_READY_B__GPIO3_IO16	0x140
 		>;
 	};
 
 	pinctrl_i2c1: i2c1grp {
 		fsl,pins = <
-			MX8MP_IOMUXC_I2C1_SCL__I2C1_SCL		0x400001c3
-			MX8MP_IOMUXC_I2C1_SDA__I2C1_SDA		0x400001c3
+			MX8MP_IOMUXC_I2C1_SCL__I2C1_SCL		0x400001c2
+			MX8MP_IOMUXC_I2C1_SDA__I2C1_SDA		0x400001c2
 		>;
 	};
 
 	pinctrl_i2c3: i2c3grp {
 		fsl,pins = <
-			MX8MP_IOMUXC_I2C3_SCL__I2C3_SCL		0x400001c3
-			MX8MP_IOMUXC_I2C3_SDA__I2C3_SDA		0x400001c3
+			MX8MP_IOMUXC_I2C3_SCL__I2C3_SCL		0x400001c2
+			MX8MP_IOMUXC_I2C3_SDA__I2C3_SDA		0x400001c2
+		>;
+	};
+
+	pinctrl_i2c5: i2c5grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SPDIF_RX__I2C5_SDA         0x400001c2
+			MX8MP_IOMUXC_SPDIF_TX__I2C5_SCL         0x400001c2
+		>;
+	};
+
+	pinctrl_pcie0: pcie0grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_I2C4_SCL__PCIE_CLKREQ_B	0x61 /* open drain, pull up */
+			MX8MP_IOMUXC_SD1_DATA5__GPIO2_IO07	0x41
+		>;
+	};
+
+	pinctrl_pcie0_reg: pcie0reggrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SD1_DATA4__GPIO2_IO06	0x41
 		>;
 	};
 
@@ -375,22 +561,28 @@
 		>;
 	};
 
+	pinctrl_pca6416_int: pca6416_int_grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_GPIO1_IO12__GPIO1_IO12	0x146 /* Input pull-up. */
+		>;
+	};
+
 	pinctrl_reg_usdhc2_vmmc: regusdhc2vmmcgrp {
 		fsl,pins = <
-			MX8MP_IOMUXC_SD2_RESET_B__GPIO2_IO19	0x41
+			MX8MP_IOMUXC_SD2_RESET_B__GPIO2_IO19	0x40
 		>;
 	};
 
 	pinctrl_uart2: uart2grp {
 		fsl,pins = <
-			MX8MP_IOMUXC_UART2_RXD__UART2_DCE_RX	0x49
-			MX8MP_IOMUXC_UART2_TXD__UART2_DCE_TX	0x49
+			MX8MP_IOMUXC_UART2_RXD__UART2_DCE_RX	0x140
+			MX8MP_IOMUXC_UART2_TXD__UART2_DCE_TX	0x140
 		>;
 	};
 
 	pinctrl_usb1_vbus: usb1grp {
 		fsl,pins = <
-			MX8MP_IOMUXC_GPIO1_IO14__USB2_OTG_PWR	0x19
+			MX8MP_IOMUXC_GPIO1_IO14__USB2_OTG_PWR	0x10
 		>;
 	};
 
@@ -402,7 +594,7 @@
 			MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1	0x1d0
 			MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2	0x1d0
 			MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3	0x1d0
-			MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT	0xc1
+			MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT	0xc0
 		>;
 	};
 
@@ -414,7 +606,7 @@
 			MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1	0x1d4
 			MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2	0x1d4
 			MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3	0x1d4
-			MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT 0xc1
+			MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT 0xc0
 		>;
 	};
 
@@ -426,7 +618,7 @@
 			MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1	0x1d6
 			MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2	0x1d6
 			MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3	0x1d6
-			MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT 0xc1
+			MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT 0xc0
 		>;
 	};
 
diff --git a/arch/arm64/boot/dts/freescale/imx8mp-icore-mx8mp-edimm2.2.dts b/arch/arm64/boot/dts/freescale/imx8mp-icore-mx8mp-edimm2.2.dts
new file mode 100644
index 000000000000..a02b31c42db4
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mp-icore-mx8mp-edimm2.2.dts
@@ -0,0 +1,175 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2018 NXP
+ * Copyright (c) 2019 Engicam srl
+ * Copyright (c) 2020 Amarula Solutions(India)
+ */
+
+/dts-v1/;
+
+#include "imx8mp.dtsi"
+#include "imx8mp-icore-mx8mp.dtsi"
+#include <dt-bindings/usb/pd.h>
+
+/ {
+	model = "Engicam i.Core MX8M Plus EDIMM2.2 Starter Kit";
+	compatible = "engicam,icore-mx8mp-edimm2.2", "engicam,icore-mx8mp",
+		     "fsl,imx8mp";
+
+	chosen {
+		stdout-path = &uart2;
+	};
+
+	reg_usb1_vbus: regulator-usb1 {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio1 14 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_usb1>;
+		regulator-max-microvolt = <5000000>;
+		regulator-min-microvolt = <5000000>;
+		regulator-name = "usb1_host_vbus";
+	};
+
+	reg_usdhc2_vmmc: regulator-usdhc2 {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>;
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "VSD_3V3";
+	};
+};
+
+/* Ethernet */
+&eqos {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_eqos>;
+	phy-handle = <&ethphy0>;
+	phy-mode = "rgmii-id";
+	status = "okay";
+
+	mdio {
+		compatible = "snps,dwmac-mdio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy0: ethernet-phy@7 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			micrel,led-mode = <0>;
+			reg = <7>;
+		};
+	};
+};
+
+/* console */
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	status = "okay";
+};
+
+&usb3_phy0 {
+	status = "okay";
+};
+
+&usb3_0 {
+	status = "okay";
+};
+
+&usb_dwc3_0 {
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usb3_phy1 {
+	status = "okay";
+};
+
+&usb3_1 {
+	status = "okay";
+};
+
+&usb_dwc3_1 {
+	dr_mode = "host";
+	status = "okay";
+};
+
+/* SDCARD */
+&usdhc2 {
+	cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
+	bus-width = <4>;
+	pinctrl-names = "default" ;
+	pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
+	vmmc-supply = <&reg_usdhc2_vmmc>;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_eqos: eqosgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_ENET_MDC__ENET_QOS_MDC				0x2
+			MX8MP_IOMUXC_ENET_MDIO__ENET_QOS_MDIO				0x2
+			MX8MP_IOMUXC_ENET_RD0__ENET_QOS_RGMII_RD0			0x90
+			MX8MP_IOMUXC_ENET_RD1__ENET_QOS_RGMII_RD1			0x90
+			MX8MP_IOMUXC_ENET_RD2__ENET_QOS_RGMII_RD2			0x90
+			MX8MP_IOMUXC_ENET_RD3__ENET_QOS_RGMII_RD3			0x90
+			MX8MP_IOMUXC_ENET_RXC__CCM_ENET_QOS_CLOCK_GENERATE_RX_CLK	0x90
+			MX8MP_IOMUXC_ENET_RX_CTL__ENET_QOS_RGMII_RX_CTL			0x90
+			MX8MP_IOMUXC_ENET_TD0__ENET_QOS_RGMII_TD0			0x16
+			MX8MP_IOMUXC_ENET_TD1__ENET_QOS_RGMII_TD1			0x16
+			MX8MP_IOMUXC_ENET_TD2__ENET_QOS_RGMII_TD2			0x16
+			MX8MP_IOMUXC_ENET_TD3__ENET_QOS_RGMII_TD3			0x16
+			MX8MP_IOMUXC_ENET_TX_CTL__ENET_QOS_RGMII_TX_CTL			0x16
+			MX8MP_IOMUXC_ENET_TXC__CCM_ENET_QOS_CLOCK_GENERATE_TX_CLK	0x16
+			MX8MP_IOMUXC_NAND_DATA01__GPIO3_IO07				0x10
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_UART2_RXD__UART2_DCE_RX	0x40
+			MX8MP_IOMUXC_UART2_TXD__UART2_DCE_TX	0x40
+		>;
+	};
+
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_UART3_RXD__UART3_DCE_RX	0x140
+			MX8MP_IOMUXC_UART3_TXD__UART3_DCE_TX	0x140
+			MX8MP_IOMUXC_SD1_STROBE__UART3_DCE_CTS	0x140
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK	0x190
+			MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD	0x1d0
+			MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0	0x1d0
+			MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1	0x1d0
+			MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2	0x1d0
+			MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3	0x1d0
+			MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT	0xc0
+		>;
+	};
+
+	pinctrl_usdhc2_gpio: usdhc2gpiogrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SD2_CD_B__GPIO2_IO12	0x1c4
+		>;
+	};
+
+	pinctrl_reg_usb1: regusb1grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_GPIO1_IO14__GPIO1_IO14	0x10
+		>;
+	};
+
+	pinctrl_reg_usdhc2_vmmc: regusdhc2vmmcgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SD2_RESET_B__GPIO2_IO19	0x40
+		>;
+	};
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mp-icore-mx8mp.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-icore-mx8mp.dtsi
new file mode 100644
index 000000000000..a6319824ea2e
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mp-icore-mx8mp.dtsi
@@ -0,0 +1,186 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2018 NXP
+ * Copyright (c) 2019 Engicam srl
+ * Copyright (c) 2020 Amarula Solutions(India)
+ */
+
+/ {
+	compatible = "engicam,icore-mx8mp", "fsl,imx8mp";
+};
+
+&A53_0 {
+	cpu-supply = <&buck2>;
+};
+
+&A53_1 {
+	cpu-supply = <&buck2>;
+};
+
+&A53_2 {
+	cpu-supply = <&buck2>;
+};
+
+&A53_3 {
+	cpu-supply = <&buck2>;
+};
+
+&i2c1 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+
+	pca9450: pmic@25 {
+		compatible = "nxp,pca9450c";
+		interrupt-parent = <&gpio3>;
+		interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_pmic>;
+		reg = <0x25>;
+
+		regulators {
+			buck1: BUCK1 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <720000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-name = "BUCK1";
+				regulator-ramp-delay = <3125>;
+			};
+
+			buck2: BUCK2  {
+				nxp,dvs-run-voltage = <950000>;
+				nxp,dvs-standby-voltage = <850000>;
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1025000>;
+				regulator-min-microvolt = <720000>;
+				regulator-name = "BUCK2";
+				regulator-ramp-delay = <3125>;
+			};
+
+			buck4: BUCK4 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <3600000>;
+				regulator-min-microvolt = <3000000>;
+				regulator-name = "BUCK4";
+			};
+
+			buck5: BUCK5 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1950000>;
+				regulator-min-microvolt = <1650000>;
+				regulator-name = "BUCK5";
+			};
+
+			buck6: BUCK6 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1155000>;
+				regulator-min-microvolt = <1045000>;
+				regulator-name = "BUCK6";
+			};
+
+			ldo1: LDO1 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1950000>;
+				regulator-min-microvolt = <1650000>;
+				regulator-name = "LDO1";
+			};
+
+			ldo3: LDO3 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1890000>;
+				regulator-min-microvolt = <1710000>;
+				regulator-name = "LDO3";
+			};
+
+			ldo5: LDO5 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <3300000>;
+				regulator-min-microvolt = <1800000>;
+				regulator-name = "LDO5";
+			};
+		};
+	};
+};
+
+/* EMMC */
+&usdhc3 {
+	bus-width = <8>;
+	non-removable;
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_I2C1_SCL__I2C1_SCL		0x400001c3
+			MX8MP_IOMUXC_I2C1_SDA__I2C1_SDA		0x400001c3
+		>;
+	};
+
+	pinctrl_pmic: pmicgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_NAND_CE0_B__GPIO3_IO01	  0x41
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK	0x190
+			MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD	0x1d0
+			MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0	0x1d0
+			MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1	0x1d0
+			MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2	0x1d0
+			MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3	0x1d0
+			MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4	0x1d0
+			MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5	0x1d0
+			MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6	0x1d0
+			MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7	0x1d0
+			MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE	0x190
+		>;
+	};
+
+	pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK	0x194
+			MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD	0x1d4
+			MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0	0x1d4
+			MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1	0x1d4
+			MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2	0x1d4
+			MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3	0x1d4
+			MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4	0x1d4
+			MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5	0x1d4
+			MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6	0x1d4
+			MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7	0x1d4
+			MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE	0x194
+		>;
+	};
+
+	pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK	0x196
+			MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD	0x1d6
+			MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0	0x1d6
+			MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1	0x1d6
+			MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2	0x1d6
+			MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3	0x1d6
+			MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4	0x1d6
+			MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5	0x1d6
+			MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6	0x1d6
+			MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7	0x1d6
+			MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE	0x196
+		>;
+	};
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mp-msc-sm2s-14N0600E.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-msc-sm2s-14N0600E.dtsi
new file mode 100644
index 000000000000..2f5cc013e8d6
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mp-msc-sm2s-14N0600E.dtsi
@@ -0,0 +1,68 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2022 Avnet Embedded GmbH
+ */
+/dts-v1/;
+
+#include "imx8mp-msc-sm2s.dtsi"
+
+/ {
+	memory@40000000 {
+		device_type = "memory";
+		reg = <0x0 0x40000000 0 0x80000000>; /* bank0, 2GiB */
+	};
+};
+
+&cpu_alert0 {
+	temperature = <95000>;
+};
+
+&cpu_crit0 {
+	temperature = <105000>;
+};
+
+&soc_alert0 {
+	temperature = <95000>;
+};
+
+&soc_crit0 {
+	temperature = <105000>;
+};
+
+&tca6424 {
+	gbe0-int-hog {
+		gpio-hog;
+		input;
+		gpios = <3 GPIO_ACTIVE_LOW>;
+	};
+
+	gbe1-int-hog {
+		gpio-hog;
+		input;
+		gpios = <4 GPIO_ACTIVE_LOW>;
+	};
+
+	cam2-rst-hog {
+		gpio-hog;
+		output-high;
+		gpios = <9 GPIO_ACTIVE_LOW>;
+	};
+
+	cam2-pwr-hog {
+		gpio-hog;
+		output-high;
+		gpios = <10 GPIO_ACTIVE_LOW>;
+	};
+
+	tpm-int-hog {
+		gpio-hog;
+		input;
+		gpios = <13 GPIO_ACTIVE_LOW>;
+	};
+
+	wifi-int-hog {
+		gpio-hog;
+		input;
+		gpios = <14 GPIO_ACTIVE_LOW>;
+	};
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mp-msc-sm2s-ep1.dts b/arch/arm64/boot/dts/freescale/imx8mp-msc-sm2s-ep1.dts
new file mode 100644
index 000000000000..470ff8e31e32
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mp-msc-sm2s-ep1.dts
@@ -0,0 +1,52 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2022 Avnet Embedded GmbH
+ */
+
+/dts-v1/;
+
+#include "imx8mp-msc-sm2s-14N0600E.dtsi"
+#include <dt-bindings/clock/imx8mp-clock.h>
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "MSC SM2-MB-EP1 Carrier Board with SM2S-IMX8PLUS-QC6-14N0600E SoM";
+	compatible = "avnet,sm2s-imx8mp-14N0600E-ep1",
+		     "avnet,sm2s-imx8mp-14N0600E", "avnet,sm2s-imx8mp",
+		     "fsl,imx8mp";
+};
+
+&flexcan1 {
+	status = "okay";
+};
+
+&flexcan2 {
+	status = "okay";
+};
+
+&usdhc2 {
+	no-1-8-v;
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_smarc_gpio>;
+
+	pinctrl_smarc_gpio: smarcgpiosgrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_GPIO1_IO11__GPIO1_IO11	0x19>, /* GPIO0 */
+			<MX8MP_IOMUXC_SAI1_RXC__GPIO4_IO01	0x19>, /* GPIO1 */
+			<MX8MP_IOMUXC_SAI1_RXD0__GPIO4_IO02	0x19>, /* GPIO2 */
+			<MX8MP_IOMUXC_SAI1_RXD1__GPIO4_IO03	0x19>, /* GPIO3 */
+			<MX8MP_IOMUXC_SAI3_RXC__GPIO4_IO29	0x19>, /* GPIO4 */
+			<MX8MP_IOMUXC_SAI3_MCLK__GPIO5_IO02	0x19>, /* GPIO5 */
+			<MX8MP_IOMUXC_SAI1_TXD6__GPIO4_IO18	0x19>, /* GPIO6 */
+			<MX8MP_IOMUXC_GPIO1_IO10__GPIO1_IO10	0x19>, /* GPIO7 */
+			<MX8MP_IOMUXC_SAI1_MCLK__GPIO4_IO20	0x19>, /* GPIO8 */
+			<MX8MP_IOMUXC_SAI2_RXFS__GPIO4_IO21	0x19>, /* GPIO9 */
+			<MX8MP_IOMUXC_SAI2_RXC__GPIO4_IO22	0x19>, /* GPIO10 */
+			<MX8MP_IOMUXC_SAI3_RXFS__GPIO4_IO28	0x19>, /* GPIO11 */
+			<MX8MP_IOMUXC_SAI1_TXD7__GPIO4_IO19	0x19>, /* GPIO12 */
+			<MX8MP_IOMUXC_SAI1_RXFS__GPIO4_IO00	0x19>; /* GPIO13 */
+	};
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mp-msc-sm2s.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-msc-sm2s.dtsi
new file mode 100644
index 000000000000..5dbec71747c3
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mp-msc-sm2s.dtsi
@@ -0,0 +1,820 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2022 Avnet Embedded GmbH
+ */
+
+/dts-v1/;
+
+#include "imx8mp.dtsi"
+#include <dt-bindings/net/ti-dp83867.h>
+
+/ {
+	aliases {
+		rtc0 = &sys_rtc;
+		rtc1 = &snvs_rtc;
+	};
+
+	chosen {
+		stdout-path = &uart2;
+	};
+
+	reg_usb0_host_vbus: regulator-usb0-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb0_host_vbus";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usb0_vbus>;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	reg_usb1_host_vbus: regulator-usb1-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb1_host_vbus";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usb1_vbus>;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio1 14 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	reg_usdhc2_vmmc: regulator-usdhc2 {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usdhc2_vmmc>;
+		regulator-name = "VSD_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		startup-delay-us = <100>;
+		off-on-delay-us = <12000>;
+	};
+
+	reg_flexcan1_xceiver: regulator-flexcan1 {
+		compatible = "regulator-fixed";
+		regulator-name = "flexcan1-xceiver";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	reg_flexcan2_xceiver: regulator-flexcan2 {
+		compatible = "regulator-fixed";
+		regulator-name = "flexcan2-xceiver";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	lcd0_backlight: backlight-0 {
+		compatible = "pwm-backlight";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_lcd0_backlight>;
+		pwms = <&pwm1 0 100000 0>;
+		brightness-levels = <0 255>;
+		num-interpolated-steps = <255>;
+		default-brightness-level = <255>;
+		enable-gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>;
+		status = "disabled";
+	};
+
+	lcd1_backlight: backlight-1 {
+		compatible = "pwm-backlight";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_lcd1_backlight>;
+		pwms = <&pwm2 0 100000 0>;
+		brightness-levels = <0 255>;
+		num-interpolated-steps = <255>;
+		default-brightness-level = <255>;
+		enable-gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>;
+		status = "disabled";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_leds>;
+		status = "okay";
+
+		led-sw {
+			label = "sw-led";
+			gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	extcon_usb0: extcon-usb0 {
+		compatible = "linux,extcon-usb-gpio";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usb0_extcon>;
+		id-gpio = <&gpio1 3 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&A53_0 {
+	cpu-supply = <&vcc_arm>;
+};
+
+&A53_1 {
+	cpu-supply = <&vcc_arm>;
+};
+
+&A53_2 {
+	cpu-supply = <&vcc_arm>;
+};
+
+&A53_3 {
+	cpu-supply = <&vcc_arm>;
+};
+
+&ecspi1 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1>;
+	cs-gpios = <0>, <&gpio2 8 GPIO_ACTIVE_LOW>;
+};
+
+&ecspi2 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi2>;
+	cs-gpios = <0>, <&gpio2 9 GPIO_ACTIVE_LOW>;
+};
+
+&eqos {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_eqos>;
+	phy-mode = "rgmii-id";
+	phy-handle = <&ethphy0>;
+	status = "okay";
+
+	mdio {
+		compatible = "snps,dwmac-mdio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy0: ethernet-phy@1 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <1>;
+			eee-broken-1000t;
+			reset-gpios = <&tca6424 16 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <1000>;
+			reset-deassert-us = <1000>;
+			ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>;
+			ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>;
+			ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+			ti,clk-output-sel = <DP83867_CLK_O_SEL_OFF>;
+		};
+	};
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_fec>;
+	phy-mode = "rgmii-id";
+	phy-handle = <&ethphy1>;
+	fsl,magic-packet;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy1: ethernet-phy@1 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <1>;
+			eee-broken-1000t;
+			reset-gpios = <&tca6424 17 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <1000>;
+			reset-deassert-us = <1000>;
+			ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>;
+			ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>;
+			ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+			ti,clk-output-sel = <DP83867_CLK_O_SEL_OFF>;
+		};
+	};
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	clock-frequency = <400000>;
+	status = "okay";
+
+	id_eeprom: eeprom@50 {
+		compatible = "atmel,24c64";
+		reg = <0x50>;
+		pagesize = <32>;
+	};
+};
+
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	clock-frequency = <400000>;
+	status = "disabled";
+};
+
+&i2c3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	clock-frequency = <400000>;
+	status = "disabled";
+};
+
+&i2c4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c4>;
+	clock-frequency = <400000>;
+	status = "disabled";
+};
+
+&i2c5 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c5>;
+	clock-frequency = <400000>;
+	status = "disabled";
+};
+
+&i2c6 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c6>;
+	clock-frequency = <400000>;
+	status = "okay";
+
+	tca6424: gpio@22 {
+		compatible = "ti,tca6424";
+		reg = <0x22>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_tca6424>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names = "BOOT_SEL0#", "BOOT_SEL1#", "BOOT_SEL2#",
+			"gbe0_int", "gbe1_int", "pmic_int", "rtc_int", "lvds_int",
+			"PCIE_WAKE#", "cam2_rst", "cam2_pwr", "SLEEP#",
+			"wifi_pd", "tpm_int", "wifi_int", "PCIE_A_RST#",
+			"gbe0_rst", "gbe1_rst", "LID#", "BATLOW#", "CHARGING#",
+			"CHARGER_PRSNT#";
+		interrupt-parent = <&gpio1>;
+		interrupts = <9 IRQ_TYPE_EDGE_RISING>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	dsi_lvds_bridge: bridge@2d {
+		compatible = "ti,sn65dsi83";
+		reg = <0x2d>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_lvds_bridge>;
+		enable-gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
+		status = "disabled";
+	};
+
+	pmic: pmic@30 {
+		compatible = "ricoh,rn5t567";
+		reg = <0x30>;
+		interrupt-parent = <&tca6424>;
+		interrupts = <5 IRQ_TYPE_EDGE_FALLING>;
+
+		regulators {
+			DCDC1 {
+				regulator-name = "VCC_SOC";
+				regulator-always-on;
+				regulator-min-microvolt = <950000>;
+				regulator-max-microvolt = <950000>;
+			};
+
+			DCDC2 {
+				regulator-name = "VCC_DRAM";
+				regulator-always-on;
+				regulator-min-microvolt = <1100000>;
+				regulator-max-microvolt = <1100000>;
+			};
+
+			vcc_arm: DCDC3 {
+				regulator-name = "VCC_ARM";
+				regulator-always-on;
+				regulator-min-microvolt = <950000>;
+				regulator-max-microvolt = <950000>;
+			};
+
+			DCDC4 {
+				regulator-name = "VCC_1V8";
+				regulator-always-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+
+			LDO1 {
+				regulator-name = "VCC_LDO1_2V5";
+				regulator-always-on;
+				regulator-min-microvolt = <2500000>;
+				regulator-max-microvolt = <2500000>;
+			};
+
+			LDO2 {
+				regulator-name = "VCC_LDO2_1V8";
+				regulator-always-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+
+			LDO3 {
+				regulator-name = "VCC_ETH_2V5";
+				regulator-always-on;
+				regulator-min-microvolt = <2500000>;
+				regulator-max-microvolt = <2500000>;
+			};
+
+			LDO4 {
+				regulator-name = "VCC_DDR4_2V5";
+				regulator-always-on;
+				regulator-min-microvolt = <2500000>;
+				regulator-max-microvolt = <2500000>;
+			};
+
+			LDO5 {
+				regulator-name = "VCC_LDO5_1V8";
+				regulator-always-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+
+			LDORTC1 {
+				regulator-name = "VCC_SNVS_1V8";
+				regulator-always-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+
+			LDORTC2 {
+				regulator-name = "VCC_SNVS_3V3";
+				regulator-always-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+			};
+		};
+	};
+
+	sys_rtc: rtc@32 {
+		compatible = "ricoh,r2221tl";
+		reg = <0x32>;
+		interrupt-parent = <&tca6424>;
+		interrupts = <6 IRQ_TYPE_EDGE_FALLING>;
+	};
+
+	tmp_sensor: temperature-sensor@71 {
+		compatible = "ti,tmp103";
+		reg = <0x71>;
+	};
+};
+
+&flexcan1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan1>;
+	xceiver-supply = <&reg_flexcan1_xceiver>;
+	status = "disabled";
+};
+
+&flexcan2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan2>;
+	xceiver-supply = <&reg_flexcan2_xceiver>;
+	status = "disabled";
+};
+
+&flexspi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexspi0>;
+	status = "okay";
+
+	qspi_flash: flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		spi-max-frequency = <80000000>;
+		spi-tx-bus-width = <4>;
+		spi-rx-bus-width = <4>;
+	};
+};
+
+&pwm1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm1>;
+	status = "disabled";
+};
+
+&pwm2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm2>;
+	status = "disabled";
+};
+
+&pwm3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm3>;
+	status = "disabled";
+};
+
+&pwm4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm4>;
+	status = "disabled";
+};
+
+&snvs_pwrkey {
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+	status = "disabled";
+};
+
+&usb3_phy0 {
+	vbus-supply = <&reg_usb0_host_vbus>;
+	status = "okay";
+};
+
+&usb3_phy1 {
+	vbus-supply = <&reg_usb1_host_vbus>;
+	status = "okay";
+};
+
+&usb3_0 {
+	status = "okay";
+};
+
+&usb3_1 {
+	status = "okay";
+};
+
+&usb_dwc3_0 {
+	dr_mode = "otg";
+	hnp-disable;
+	srp-disable;
+	adp-disable;
+	extcon = <&extcon_usb0>;
+	status = "okay";
+};
+
+&usb_dwc3_1 {
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usdhc2 {
+	assigned-clocks = <&clk IMX8MP_CLK_USDHC2>;
+	assigned-clock-rates = <400000000>;
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
+	cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio2 20 GPIO_ACTIVE_HIGH>;
+	bus-width = <4>;
+	vmmc-supply = <&reg_usdhc2_vmmc>;
+	status = "okay";
+};
+
+&usdhc3 {
+	assigned-clocks = <&clk IMX8MP_CLK_USDHC3>;
+	assigned-clock-rates = <400000000>;
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+	bus-width = <8>;
+	non-removable;
+	status = "okay";
+};
+
+&wdog1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog>;
+	fsl,ext-reset-output;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_ecspi1: ecspi1grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_ECSPI1_MISO__ECSPI1_MISO		0x82>,
+			<MX8MP_IOMUXC_ECSPI1_MOSI__ECSPI1_MOSI		0x82>,
+			<MX8MP_IOMUXC_ECSPI1_SCLK__ECSPI1_SCLK		0x82>,
+			<MX8MP_IOMUXC_ECSPI1_SS0__ECSPI1_SS0		0x40000>,
+			<MX8MP_IOMUXC_SD1_DATA6__GPIO2_IO08		0x40000>;
+	};
+
+	pinctrl_ecspi2: ecspi2grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_ECSPI2_MISO__ECSPI2_MISO		0x82>,
+			<MX8MP_IOMUXC_ECSPI2_MOSI__ECSPI2_MOSI		0x82>,
+			<MX8MP_IOMUXC_ECSPI2_SCLK__ECSPI2_SCLK		0x82>,
+			<MX8MP_IOMUXC_ECSPI2_SS0__ECSPI2_SS0		0x40000>,
+			<MX8MP_IOMUXC_SD1_DATA7__GPIO2_IO09		0x40000>;
+	};
+
+	pinctrl_eqos: eqosgrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_ENET_MDC__ENET_QOS_MDC		0x3>,
+			<MX8MP_IOMUXC_ENET_MDIO__ENET_QOS_MDIO		0x3>,
+			<MX8MP_IOMUXC_ENET_RD0__ENET_QOS_RGMII_RD0	0x91>,
+			<MX8MP_IOMUXC_ENET_RD1__ENET_QOS_RGMII_RD1	0x91>,
+			<MX8MP_IOMUXC_ENET_RD2__ENET_QOS_RGMII_RD2	0x91>,
+			<MX8MP_IOMUXC_ENET_RD3__ENET_QOS_RGMII_RD3	0x91>,
+			<MX8MP_IOMUXC_ENET_RXC__CCM_ENET_QOS_CLOCK_GENERATE_RX_CLK	0x91>,
+			<MX8MP_IOMUXC_ENET_RX_CTL__ENET_QOS_RGMII_RX_CTL	0x91>,
+			<MX8MP_IOMUXC_ENET_TD0__ENET_QOS_RGMII_TD0	0x1f>,
+			<MX8MP_IOMUXC_ENET_TD1__ENET_QOS_RGMII_TD1	0x1f>,
+			<MX8MP_IOMUXC_ENET_TD2__ENET_QOS_RGMII_TD2	0x1f>,
+			<MX8MP_IOMUXC_ENET_TD3__ENET_QOS_RGMII_TD3	0x1f>,
+			<MX8MP_IOMUXC_ENET_TX_CTL__ENET_QOS_RGMII_TX_CTL	0x1f>,
+			<MX8MP_IOMUXC_ENET_TXC__CCM_ENET_QOS_CLOCK_GENERATE_TX_CLK	0x1f>;
+	};
+
+	pinctrl_fec: fecgrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_SAI1_RXD2__ENET1_MDC		0x3>,
+			<MX8MP_IOMUXC_SAI1_RXD3__ENET1_MDIO		0x3>,
+			<MX8MP_IOMUXC_SAI1_RXD4__ENET1_RGMII_RD0	0x91>,
+			<MX8MP_IOMUXC_SAI1_RXD5__ENET1_RGMII_RD1	0x91>,
+			<MX8MP_IOMUXC_SAI1_RXD6__ENET1_RGMII_RD2	0x91>,
+			<MX8MP_IOMUXC_SAI1_RXD7__ENET1_RGMII_RD3	0x91>,
+			<MX8MP_IOMUXC_SAI1_TXC__ENET1_RGMII_RXC		0x91>,
+			<MX8MP_IOMUXC_SAI1_TXFS__ENET1_RGMII_RX_CTL	0x91>,
+			<MX8MP_IOMUXC_SAI1_TXD0__ENET1_RGMII_TD0	0x1f>,
+			<MX8MP_IOMUXC_SAI1_TXD1__ENET1_RGMII_TD1	0x1f>,
+			<MX8MP_IOMUXC_SAI1_TXD2__ENET1_RGMII_TD2	0x1f>,
+			<MX8MP_IOMUXC_SAI1_TXD3__ENET1_RGMII_TD3	0x1f>,
+			<MX8MP_IOMUXC_SAI1_TXD4__ENET1_RGMII_TX_CTL	0x1f>,
+			<MX8MP_IOMUXC_SAI1_TXD5__ENET1_RGMII_TXC	0x1f>;
+	};
+
+	pinctrl_flexcan1: flexcan1grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_SAI5_RXD1__CAN1_TX		0x154>,
+			<MX8MP_IOMUXC_SAI5_RXD2__CAN1_RX		0x154>;
+	};
+
+	pinctrl_flexcan2: flexcan2grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_SAI5_MCLK__CAN2_RX		0x154>,
+			<MX8MP_IOMUXC_SAI5_RXD3__CAN2_TX		0x154>;
+	};
+
+	pinctrl_flexspi0: flexspi0grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_NAND_ALE__FLEXSPI_A_SCLK		0x1c2>,
+			<MX8MP_IOMUXC_NAND_CE0_B__FLEXSPI_A_SS0_B	0x82>,
+			<MX8MP_IOMUXC_NAND_DATA00__FLEXSPI_A_DATA00	0x82>,
+			<MX8MP_IOMUXC_NAND_DATA01__FLEXSPI_A_DATA01	0x82>,
+			<MX8MP_IOMUXC_NAND_DATA02__FLEXSPI_A_DATA02	0x82>,
+			<MX8MP_IOMUXC_NAND_DATA03__FLEXSPI_A_DATA03	0x82>,
+			<MX8MP_IOMUXC_NAND_DQS__GPIO3_IO14		0x19>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_I2C1_SCL__I2C1_SCL		0x400001c3>,
+			<MX8MP_IOMUXC_I2C1_SDA__I2C1_SDA		0x400001c3>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_I2C2_SCL__I2C2_SCL		0x400001c3>,
+			<MX8MP_IOMUXC_I2C2_SDA__I2C2_SDA		0x400001c3>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_I2C3_SCL__I2C3_SCL		0x400001c3>,
+			<MX8MP_IOMUXC_I2C3_SDA__I2C3_SDA		0x400001c3>;
+	};
+
+	pinctrl_i2c4: i2c4grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_I2C4_SCL__I2C4_SCL		0x400001c3>,
+			<MX8MP_IOMUXC_I2C4_SDA__I2C4_SDA		0x400001c3>;
+	};
+
+	pinctrl_i2c5: i2c5grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_SPDIF_TX__I2C5_SCL		0x400001c3>,
+			<MX8MP_IOMUXC_SPDIF_RX__I2C5_SDA		0x400001c3>;
+	};
+
+	pinctrl_i2c6: i2c6grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_SAI5_RXFS__I2C6_SCL		0x400001c3>,
+			<MX8MP_IOMUXC_SAI5_RXC__I2C6_SDA		0x400001c3>;
+	};
+
+	pinctrl_lcd0_backlight: lcd0-backlightgrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_GPIO1_IO05__GPIO1_IO05		0x41>;
+	};
+
+	pinctrl_lcd1_backlight: lcd1-backlightgrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_GPIO1_IO06__GPIO1_IO06		0x41>;
+	};
+
+	pinctrl_leds: ledsgrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_GPIO1_IO08__GPIO1_IO08		0x19>;
+	};
+
+	pinctrl_lvds_bridge: lvds-bridgegrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_GPIO1_IO07__GPIO1_IO07		0x41>;
+	};
+
+	pinctrl_pwm1: pwm1grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_SPDIF_EXT_CLK__PWM1_OUT		0x116>;
+	};
+
+	pinctrl_pwm2: pwm2grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_SAI5_RXD0__PWM2_OUT		0x116>;
+	};
+
+	pinctrl_pwm3: pwm3grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_GPIO1_IO10__PWM3_OUT		0x116>;
+	};
+
+	pinctrl_pwm4: pwm4grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_SAI3_MCLK__PWM4_OUT		0x116>;
+	};
+
+	pinctrl_tca6424: tca6424grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_GPIO1_IO09__GPIO1_IO09		0x41>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_UART1_RXD__UART1_DCE_RX		0x49>,
+			<MX8MP_IOMUXC_UART1_TXD__UART1_DCE_TX		0x49>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_SD1_DATA4__GPIO2_IO06		0x1c4>,
+			<MX8MP_IOMUXC_SD1_DATA5__GPIO2_IO07		0x1c4>,
+			<MX8MP_IOMUXC_UART2_RXD__UART2_DCE_RX		0x49>,
+			<MX8MP_IOMUXC_UART2_TXD__UART2_DCE_TX		0x49>;
+	};
+
+	pinctrl_uart3: uart3grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_SD1_RESET_B__GPIO2_IO10		0x1c4>,
+			<MX8MP_IOMUXC_SD1_STROBE__GPIO2_IO11		0x1c4>,
+			<MX8MP_IOMUXC_UART3_RXD__UART3_DCE_RX		0x49>,
+			<MX8MP_IOMUXC_UART3_TXD__UART3_DCE_TX		0x49>;
+	};
+
+	pinctrl_uart4: uart4grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_UART4_RXD__UART4_DCE_RX		0x49>,
+			<MX8MP_IOMUXC_UART4_TXD__UART4_DCE_TX		0x49>;
+	};
+
+	pinctrl_usb0_extcon: usb0-extcongrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_GPIO1_IO03__GPIO1_IO03		0x19>;
+	};
+
+	pinctrl_usb0_vbus: usb0-vbusgrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_GPIO1_IO12__GPIO1_IO12		0x19>;
+	};
+
+	pinctrl_usb1_vbus: usb1-vbusgrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_GPIO1_IO14__GPIO1_IO14		0x19>;
+	};
+
+	pinctrl_usdhc2_gpio: usdhc2-gpiogrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_SD2_CD_B__GPIO2_IO12		0x1c4>,
+			<MX8MP_IOMUXC_SD2_WP__GPIO2_IO20		0x1c4>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK		0x190>,
+			<MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD		0x1d0>,
+			<MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0		0x1d0>,
+			<MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1		0x1d0>,
+			<MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2		0x1d0>,
+			<MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3		0x1d0>,
+			<MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT	0xc1>;
+	};
+
+	pinctrl_usdhc2_vmmc: usdhc2-vmmcgrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_SD2_RESET_B__GPIO2_IO19		0x41>;
+	};
+
+	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK		0x194>,
+			<MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD		0x1d4>,
+			<MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0		0x1d4>,
+			<MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1		0x1d4>,
+			<MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2		0x1d4>,
+			<MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3		0x1d4>,
+			<MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT	0xc1>;
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK		0x196>,
+			<MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD		0x1d6>,
+			<MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0		0x1d6>,
+			<MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1		0x1d6>,
+			<MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2		0x1d6>,
+			<MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3		0x1d6>,
+			<MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT	0xc1>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK		0x190>,
+			<MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD		0x1d0>,
+			<MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0		0x1d0>,
+			<MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1		0x1d0>,
+			<MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2		0x1d0>,
+			<MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3		0x1d0>,
+			<MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4		0x1d0>,
+			<MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5		0x1d0>,
+			<MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6		0x1d0>,
+			<MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7		0x1d0>,
+			<MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE		0x190>;
+	};
+
+	pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK		0x194>,
+			<MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD		0x1d4>,
+			<MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0		0x1d4>,
+			<MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1		0x1d4>,
+			<MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2		0x1d4>,
+			<MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3		0x1d4>,
+			<MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4		0x1d4>,
+			<MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5		0x1d4>,
+			<MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6		0x1d4>,
+			<MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7		0x1d4>,
+			<MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE		0x194>;
+	};
+
+	pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK		0x196>,
+			<MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD		0x1d6>,
+			<MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0		0x1d6>,
+			<MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1		0x1d6>,
+			<MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2		0x1d6>,
+			<MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3		0x1d6>,
+			<MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4		0x1d6>,
+			<MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5		0x1d6>,
+			<MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6		0x1d6>,
+			<MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7		0x1d6>,
+			<MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE		0x196>;
+	};
+
+	pinctrl_wdog: wdoggrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_GPIO1_IO02__WDOG1_WDOG_B		0xc6>;
+	};
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mp-phyboard-pollux-rdk.dts b/arch/arm64/boot/dts/freescale/imx8mp-phyboard-pollux-rdk.dts
index 984a6b9ded8d..6aa720bafe28 100644
--- a/arch/arm64/boot/dts/freescale/imx8mp-phyboard-pollux-rdk.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mp-phyboard-pollux-rdk.dts
@@ -116,48 +116,48 @@
 &iomuxc {
 	pinctrl_eqos: eqosgrp {
 		fsl,pins = <
-			MX8MP_IOMUXC_ENET_MDC__ENET_QOS_MDC			0x3
-			MX8MP_IOMUXC_ENET_MDIO__ENET_QOS_MDIO			0x3
-			MX8MP_IOMUXC_ENET_RD0__ENET_QOS_RGMII_RD0		0x91
-			MX8MP_IOMUXC_ENET_RD1__ENET_QOS_RGMII_RD1		0x91
-			MX8MP_IOMUXC_ENET_RD2__ENET_QOS_RGMII_RD2		0x91
-			MX8MP_IOMUXC_ENET_RD3__ENET_QOS_RGMII_RD3		0x91
-			MX8MP_IOMUXC_ENET_RXC__CCM_ENET_QOS_CLOCK_GENERATE_RX_CLK	0x91
-			MX8MP_IOMUXC_ENET_RX_CTL__ENET_QOS_RGMII_RX_CTL		0x91
-			MX8MP_IOMUXC_ENET_TD0__ENET_QOS_RGMII_TD0		0x1f
-			MX8MP_IOMUXC_ENET_TD1__ENET_QOS_RGMII_TD1		0x1f
-			MX8MP_IOMUXC_ENET_TD2__ENET_QOS_RGMII_TD2		0x1f
-			MX8MP_IOMUXC_ENET_TD3__ENET_QOS_RGMII_TD3		0x1f
-			MX8MP_IOMUXC_ENET_TX_CTL__ENET_QOS_RGMII_TX_CTL		0x1f
-			MX8MP_IOMUXC_ENET_TXC__CCM_ENET_QOS_CLOCK_GENERATE_TX_CLK	0x1f
+			MX8MP_IOMUXC_ENET_MDC__ENET_QOS_MDC			0x2
+			MX8MP_IOMUXC_ENET_MDIO__ENET_QOS_MDIO			0x2
+			MX8MP_IOMUXC_ENET_RD0__ENET_QOS_RGMII_RD0		0x90
+			MX8MP_IOMUXC_ENET_RD1__ENET_QOS_RGMII_RD1		0x90
+			MX8MP_IOMUXC_ENET_RD2__ENET_QOS_RGMII_RD2		0x90
+			MX8MP_IOMUXC_ENET_RD3__ENET_QOS_RGMII_RD3		0x90
+			MX8MP_IOMUXC_ENET_RXC__CCM_ENET_QOS_CLOCK_GENERATE_RX_CLK	0x90
+			MX8MP_IOMUXC_ENET_RX_CTL__ENET_QOS_RGMII_RX_CTL		0x90
+			MX8MP_IOMUXC_ENET_TD0__ENET_QOS_RGMII_TD0		0x16
+			MX8MP_IOMUXC_ENET_TD1__ENET_QOS_RGMII_TD1		0x16
+			MX8MP_IOMUXC_ENET_TD2__ENET_QOS_RGMII_TD2		0x16
+			MX8MP_IOMUXC_ENET_TD3__ENET_QOS_RGMII_TD3		0x16
+			MX8MP_IOMUXC_ENET_TX_CTL__ENET_QOS_RGMII_TX_CTL		0x16
+			MX8MP_IOMUXC_ENET_TXC__CCM_ENET_QOS_CLOCK_GENERATE_TX_CLK	0x16
 			MX8MP_IOMUXC_SAI1_MCLK__GPIO4_IO20			0x10
 		>;
 	};
 
 	pinctrl_i2c2: i2c2grp {
 		fsl,pins = <
-			MX8MP_IOMUXC_I2C2_SCL__I2C2_SCL		0x400001c3
-			MX8MP_IOMUXC_I2C2_SDA__I2C2_SDA		0x400001c3
+			MX8MP_IOMUXC_I2C2_SCL__I2C2_SCL		0x400001c2
+			MX8MP_IOMUXC_I2C2_SDA__I2C2_SDA		0x400001c2
 		>;
 	};
 
 	pinctrl_i2c2_gpio: i2c2gpiogrp {
 		fsl,pins = <
-			MX8MP_IOMUXC_I2C2_SCL__GPIO5_IO16	0x1e3
-			MX8MP_IOMUXC_I2C2_SDA__GPIO5_IO17	0x1e3
+			MX8MP_IOMUXC_I2C2_SCL__GPIO5_IO16	0x1e2
+			MX8MP_IOMUXC_I2C2_SDA__GPIO5_IO17	0x1e2
 		>;
 	};
 
 	pinctrl_reg_usdhc2_vmmc: regusdhc2vmmcgrp {
 		fsl,pins = <
-			MX8MP_IOMUXC_SD2_RESET_B__GPIO2_IO19	0x41
+			MX8MP_IOMUXC_SD2_RESET_B__GPIO2_IO19	0x40
 		>;
 	};
 
 	pinctrl_uart1: uart1grp {
 		fsl,pins = <
-			MX8MP_IOMUXC_UART1_RXD__UART1_DCE_RX	0x49
-			MX8MP_IOMUXC_UART1_TXD__UART1_DCE_TX	0x49
+			MX8MP_IOMUXC_UART1_RXD__UART1_DCE_RX	0x40
+			MX8MP_IOMUXC_UART1_TXD__UART1_DCE_TX	0x40
 		>;
 	};
 
@@ -175,7 +175,7 @@
 			MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1	0x1d0
 			MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2	0x1d0
 			MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3	0x1d0
-			MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT	0xc1
+			MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT	0xc0
 		>;
 	};
 
@@ -187,7 +187,7 @@
 			MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1	0x1d4
 			MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2	0x1d4
 			MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3	0x1d4
-			MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT	0xc1
+			MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT	0xc0
 		>;
 	};
 
@@ -199,7 +199,7 @@
 			MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1	0x1d6
 			MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2	0x1d6
 			MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3	0x1d6
-			MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT	0xc1
+			MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT	0xc0
 		>;
 	};
 };
diff --git a/arch/arm64/boot/dts/freescale/imx8mp-phycore-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-phycore-som.dtsi
index fc178eebf8aa..79b290a002c1 100644
--- a/arch/arm64/boot/dts/freescale/imx8mp-phycore-som.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mp-phycore-som.dtsi
@@ -60,6 +60,7 @@
 			ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
 			ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
 			ti,clk-output-sel = <DP83867_CLK_O_SEL_OFF>;
+			ti,min-output-impedance;
 			enet-phy-lane-no-swap;
 		};
 	};
@@ -113,6 +114,8 @@
 				regulator-boot-on;
 				regulator-always-on;
 				regulator-ramp-delay = <3125>;
+				nxp,dvs-run-voltage = <950000>;
+				nxp,dvs-standby-voltage = <850000>;
 			};
 
 			buck4: BUCK4 {
@@ -167,14 +170,14 @@
 				regulator-compatible = "LDO4";
 				regulator-min-microvolt = <800000>;
 				regulator-max-microvolt = <3300000>;
-				regulator-boot-on;
-				regulator-always-on;
 			};
 
 			ldo5: LDO5 {
 				regulator-compatible = "LDO5";
 				regulator-min-microvolt = <1800000>;
 				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
 			};
 		};
 	};
@@ -194,6 +197,8 @@
 
 /* eMMC */
 &usdhc3 {
+	assigned-clocks = <&clk IMX8MP_CLK_USDHC3_ROOT>;
+	assigned-clock-rates = <400000000>;
 	pinctrl-names = "default", "state_100mhz", "state_200mhz";
 	pinctrl-0 = <&pinctrl_usdhc3>;
 	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
@@ -221,12 +226,12 @@
 			MX8MP_IOMUXC_SAI1_RXD7__ENET1_RGMII_RD3		0x91
 			MX8MP_IOMUXC_SAI1_TXC__ENET1_RGMII_RXC		0x91
 			MX8MP_IOMUXC_SAI1_TXFS__ENET1_RGMII_RX_CTL	0x91
-			MX8MP_IOMUXC_SAI1_TXD0__ENET1_RGMII_TD0		0x1f
-			MX8MP_IOMUXC_SAI1_TXD1__ENET1_RGMII_TD1		0x1f
-			MX8MP_IOMUXC_SAI1_TXD2__ENET1_RGMII_TD2		0x1f
-			MX8MP_IOMUXC_SAI1_TXD3__ENET1_RGMII_TD3		0x1f
-			MX8MP_IOMUXC_SAI1_TXD4__ENET1_RGMII_TX_CTL	0x1f
-			MX8MP_IOMUXC_SAI1_TXD5__ENET1_RGMII_TXC		0x1f
+			MX8MP_IOMUXC_SAI1_TXD0__ENET1_RGMII_TD0		0x12
+			MX8MP_IOMUXC_SAI1_TXD1__ENET1_RGMII_TD1		0x12
+			MX8MP_IOMUXC_SAI1_TXD2__ENET1_RGMII_TD2		0x14
+			MX8MP_IOMUXC_SAI1_TXD3__ENET1_RGMII_TD3		0x14
+			MX8MP_IOMUXC_SAI1_TXD4__ENET1_RGMII_TX_CTL	0x14
+			MX8MP_IOMUXC_SAI1_TXD5__ENET1_RGMII_TXC		0x14
 			MX8MP_IOMUXC_GPIO1_IO15__GPIO1_IO15		0x11
 		>;
 	};
@@ -298,21 +303,21 @@
 		fsl,pins = <
 			MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK	0x196
 			MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD	0x1d6
-			MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0	0x1d6
-			MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1	0x1d6
-			MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2	0x1d6
-			MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3	0x1d6
-			MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4	0x1d6
-			MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5	0x1d6
-			MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6	0x1d6
-			MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7	0x1d6
+			MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0	0x1d2
+			MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1	0x1d2
+			MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2	0x1d2
+			MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3	0x1d2
+			MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4	0x1d2
+			MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5	0x1d2
+			MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6	0x1d2
+			MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7	0x1d2
 			MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE	0x196
 		>;
 	};
 
 	pinctrl_wdog: wdoggrp {
 		fsl,pins = <
-			MX8MP_IOMUXC_GPIO1_IO02__WDOG1_WDOG_B	0xc6
+			MX8MP_IOMUXC_GPIO1_IO02__WDOG1_WDOG_B	0xe6
 		>;
 	};
 };
diff --git a/arch/arm64/boot/dts/freescale/imx8mp-tqma8mpql-mba8mpxl.dts b/arch/arm64/boot/dts/freescale/imx8mp-tqma8mpql-mba8mpxl.dts
new file mode 100644
index 000000000000..7bf6f81e87b4
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mp-tqma8mpql-mba8mpxl.dts
@@ -0,0 +1,756 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2021-2022 TQ-Systems GmbH
+ * Author: Alexander Stein <alexander.stein@tq-group.com>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/net/ti-dp83867.h>
+#include <dt-bindings/pwm/pwm.h>
+#include "imx8mp-tqma8mpql.dtsi"
+
+/ {
+	model = "TQ-Systems i.MX8MPlus TQMa8MPxL on MBa8MPxL";
+	compatible = "tq,imx8mp-tqma8mpql-mba8mpxl", "tq,imx8mp-tqma8mpql", "fsl,imx8mp";
+
+	chosen {
+		stdout-path = &uart4;
+	};
+
+	iio-hwmon {
+		compatible = "iio-hwmon";
+		io-channels = <&adc 0>, <&adc 1>;
+	};
+
+	aliases {
+		mmc0 = &usdhc3;
+		mmc1 = &usdhc2;
+		mmc2 = &usdhc1;
+		rtc0 = &pcf85063;
+		rtc1 = &snvs_rtc;
+		spi0 = &flexspi;
+		spi1 = &ecspi1;
+		spi2 = &ecspi2;
+		spi3 = &ecspi3;
+	};
+
+	backlight_lvds: backlight {
+		compatible = "pwm-backlight";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_backlight>;
+		pwms = <&pwm2 0 5000000 0>;
+		brightness-levels = <0 4 8 16 32 64 128 255>;
+		default-brightness-level = <7>;
+		power-supply = <&reg_vcc_12v0>;
+		enable-gpios = <&gpio3 19 GPIO_ACTIVE_HIGH>;
+		status = "disabled";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpiobutton>;
+		autorepeat;
+
+		switch-1 {
+			label = "S12";
+			linux,code = <BTN_0>;
+			gpios = <&gpio5 27 GPIO_ACTIVE_LOW>;
+		};
+
+		switch-2 {
+			label = "S13";
+			linux,code = <BTN_1>;
+			gpios = <&gpio5 26 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpioled>;
+
+		led-0 {
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_STATUS;
+			function-enumerator = <0>;
+			gpios = <&gpio5 5 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-on";
+		};
+
+		led-1 {
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_HEARTBEAT;
+			gpios = <&gpio5 4 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+
+		led-2 {
+			color = <LED_COLOR_ID_YELLOW>;
+			function = LED_FUNCTION_STATUS;
+			function-enumerator = <1>;
+			gpios = <&gpio5 3 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	display: display {
+		/*
+		 * Display is not fixed, so compatible has to be added from
+		 * DT overlay
+		 */
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_lvdsdisplay>;
+		power-supply = <&reg_vcc_3v3>;
+		enable-gpios = <&gpio3 20 GPIO_ACTIVE_HIGH>;
+		backlight = <&backlight_lvds>;
+		status = "disabled";
+	};
+
+	reg_usdhc2_vmmc: regulator-usdhc2 {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>;
+		regulator-name = "VSD_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		startup-delay-us = <100>;
+		off-on-delay-us = <12000>;
+	};
+
+	reg_vcc_12v0: regulator-12v0 {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg12v0>;
+		regulator-name = "VCC_12V0";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		gpio = <&gpio2 6 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	reg_vcc_3v3: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	reg_vcc_5v0: regulator-5v0 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_5V0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		ocram: ocram@900000 {
+			no-map;
+			reg = <0 0x900000 0 0x70000>;
+		};
+
+		/* global autoconfigured region for contiguous allocations */
+		linux,cma {
+			compatible = "shared-dma-pool";
+			reusable;
+			size = <0 0x38000000>;
+			alloc-ranges = <0 0x40000000 0 0xB0000000>;
+			linux,cma-default;
+		};
+	};
+};
+
+&ecspi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1>;
+	cs-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&ecspi2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi2>;
+	cs-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&ecspi3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi3>;
+	cs-gpios = <&gpio5 25 GPIO_ACTIVE_LOW>;
+	status = "okay";
+
+	adc: adc@0 {
+		reg = <0>;
+		compatible = "microchip,mcp3202";
+		/* 100 ksps * 18 */
+		spi-max-frequency = <1800000>;
+		vref-supply = <&reg_vcc_3v3>;
+		#io-channel-cells = <1>;
+	};
+};
+
+&eqos {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_eqos>, <&pinctrl_eqos_phy>;
+	phy-mode = "rgmii-id";
+	phy-handle = <&ethphy3>;
+	status = "okay";
+
+	mdio {
+		compatible = "snps,dwmac-mdio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy3: ethernet-phy@3 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <3>;
+			ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>;
+			ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>;
+			ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+			ti,dp83867-rxctrl-strap-quirk;
+			ti,clk-output-sel = <DP83867_CLK_O_SEL_OFF>;
+			reset-gpios = <&gpio4 2 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <500000>;
+			reset-deassert-us = <50000>;
+			enet-phy-lane-no-swap;
+			interrupt-parent = <&gpio4>;
+			interrupts = <3 IRQ_TYPE_EDGE_FALLING>;
+		};
+	};
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_fec>, <&pinctrl_fec_phy>;
+	phy-mode = "rgmii-id";
+	phy-handle = <&ethphy0>;
+	fsl,magic-packet;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy0: ethernet-phy@0 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <0>;
+			ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>;
+			ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>;
+			ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+			ti,dp83867-rxctrl-strap-quirk;
+			ti,clk-output-sel = <DP83867_CLK_O_SEL_OFF>;
+			reset-gpios = <&gpio4 0 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <500000>;
+			reset-deassert-us = <50000>;
+			enet-phy-lane-no-swap;
+			interrupt-parent = <&gpio4>;
+			interrupts = <1 IRQ_TYPE_EDGE_FALLING>;
+		};
+	};
+};
+
+&flexcan1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan1>;
+	xceiver-supply = <&reg_vcc_3v3>;
+	status = "okay";
+};
+
+&flexcan2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan2>;
+	xceiver-supply = <&reg_vcc_3v3>;
+	status = "okay";
+};
+
+&gpio1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpio1>;
+
+	gpio-line-names = "GPO1", "GPO0", "", "GPO3",
+			  "", "", "GPO2", "GPI0",
+			  "PMIC_IRQ", "GPI1", "OTG_ID", "USB_HUB_RST#",
+			  "OTG_PWR", "", "GPI2", "GPI3",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "";
+};
+
+&gpio2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hoggpio2>;
+
+	gpio-line-names = "", "", "", "",
+			  "", "", "VCC12V_EN", "PERST#",
+			  "", "", "CLKREQ#", "PEWAKE#",
+			  "USDHC2_CD", "", "", "",
+			  "", "", "", "V_SD3V3_EN",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "";
+
+	perst-hog {
+		gpio-hog;
+		gpios = <7 0>;
+		output-high;
+		line-name = "PERST#";
+	};
+
+	clkreq-hog {
+		gpio-hog;
+		gpios = <10 0>;
+		input;
+		line-name = "CLKREQ#";
+	};
+
+	pewake-hog {
+		gpio-hog;
+		gpios = <11 0>;
+		input;
+		line-name = "PEWAKE#";
+	};
+};
+
+&gpio3 {
+	gpio-line-names = "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "LVDS0_RESET#", "",
+			  "", "", "", "LVDS0_BLT_EN",
+			  "LVDS0_PWR_EN", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "";
+};
+
+&gpio4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpio4>;
+
+	gpio-line-names = "ENET0_RST#", "ENET0_INT#", "ENET1_RST#", "ENET1_INT#",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "", "DP_IRQ", "DSI_EN",
+			  "HDMI_OC#", "TEMP_EVENT#", "PCIE_CLK_OE#", "",
+			  "", "", "", "FAN_PWR",
+			  "RTC_EVENT#", "CODEC_RST#", "", "";
+};
+
+&gpio5 {
+	gpio-line-names = "", "", "", "LED2",
+			  "LED1", "LED0", "CSI0_RESET#", "CSI0_SYNC",
+			  "CSI0_TRIGGER", "CSI0_ENABLE", "", "",
+			  "", "ECSPI2_SS0", "", "",
+			  "", "", "", "",
+			  "", "", "", "",
+			  "", "ECSPI3_SS0", "SWITCH_A", "SWITCH_B",
+			  "", "", "", "";
+};
+
+&i2c2 {
+	clock-frequency = <384000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	pinctrl-1 = <&pinctrl_i2c2_gpio>;
+	scl-gpios = <&gpio5 16 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio5 17 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "okay";
+
+	/* NXP SE97BTP with temperature sensor + eeprom */
+	se97_1c: temperature-sensor-eeprom@1c {
+		compatible = "nxp,se97", "jedec,jc-42.4-temp";
+		reg = <0x1c>;
+	};
+
+	at24c02_54: eeprom@54 {
+		compatible = "nxp,se97b", "atmel,24c02";
+		reg = <0x54>;
+		pagesize = <16>;
+		vcc-supply = <&reg_vcc_3v3>;
+	};
+};
+
+&i2c4 {
+	clock-frequency = <384000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c4>;
+	pinctrl-1 = <&pinctrl_i2c4_gpio>;
+	scl-gpios = <&gpio5 20 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio5 21 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "okay";
+};
+
+&i2c6 {
+	clock-frequency = <384000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c6>;
+	pinctrl-1 = <&pinctrl_i2c6_gpio>;
+	scl-gpios = <&gpio2 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio2 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "okay";
+};
+
+&pcf85063 {
+	/* RTC_EVENT# is connected on MBa8MPxL */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pcf85063>;
+	interrupt-parent = <&gpio4>;
+	interrupts = <28 IRQ_TYPE_EDGE_FALLING>;
+};
+
+&pwm2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm2>;
+	status = "disabled";
+};
+
+&pwm3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm3>;
+	status = "okay";
+};
+
+&snvs_pwrkey {
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	assigned-clocks = <&clk IMX8MP_CLK_UART1>;
+	assigned-clock-parents = <&clk IMX8MP_SYS_PLL1_80M>;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	assigned-clocks = <&clk IMX8MP_CLK_UART2>;
+	assigned-clock-parents = <&clk IMX8MP_SYS_PLL1_80M>;
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	assigned-clocks = <&clk IMX8MP_CLK_UART3>;
+	assigned-clock-parents = <&clk IMX8MP_SYS_PLL1_80M>;
+	status = "okay";
+};
+
+&uart4 {
+	/* console */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+	status = "okay";
+};
+
+&usb3_0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb0>;
+	fsl,over-current-active-low;
+	status = "okay";
+};
+
+&usb3_phy0 {
+	vbus-supply = <&reg_vcc_5v0>;
+	status = "okay";
+};
+
+&usb_dwc3_0 {
+	/* dual role is implemented, but not a full featured OTG */
+	hnp-disable;
+	srp-disable;
+	adp-disable;
+	dr_mode = "otg";
+	usb-role-switch;
+	role-switch-default-mode = "peripheral";
+	status = "okay";
+
+	connector {
+		compatible = "gpio-usb-b-connector", "usb-b-connector";
+		type = "micro";
+		label = "X29";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usbcon0>;
+		id-gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&usdhc2 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
+	cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
+	vmmc-supply = <&reg_usdhc2_vmmc>;
+	no-mmc;
+	no-sdio;
+	disable-wp;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_backlight: backlightgrp {
+		fsl,pins = <MX8MP_IOMUXC_SAI5_RXFS__GPIO3_IO19		0x14>;
+	};
+
+	pinctrl_flexcan1: flexcan1grp {
+		fsl,pins = <MX8MP_IOMUXC_SAI5_RXD1__CAN1_TX		0x150>,
+			   <MX8MP_IOMUXC_SAI5_RXD2__CAN1_RX		0x150>;
+	};
+
+	pinctrl_flexcan2: flexcan2grp {
+		fsl,pins = <MX8MP_IOMUXC_SAI5_RXD3__CAN2_TX		0x150>,
+			   <MX8MP_IOMUXC_SAI5_MCLK__CAN2_RX		0x150>;
+	};
+
+	/* only on X57, primary used as CSI0 control signals */
+	pinctrl_ecspi1: ecspi1grp {
+		fsl,pins = <MX8MP_IOMUXC_ECSPI1_MISO__ECSPI1_MISO	0x1c0>,
+			   <MX8MP_IOMUXC_ECSPI1_MOSI__ECSPI1_MOSI	0x1c0>,
+			   <MX8MP_IOMUXC_ECSPI1_SCLK__ECSPI1_SCLK	0x1c0>,
+			   <MX8MP_IOMUXC_ECSPI1_SS0__GPIO5_IO09		0x1c0>;
+	};
+
+	/* on X63 and optionally on X57, can also be used as CSI1 control signals */
+	pinctrl_ecspi2: ecspi2grp {
+		fsl,pins = <MX8MP_IOMUXC_ECSPI2_MISO__ECSPI2_MISO	0x1c0>,
+			   <MX8MP_IOMUXC_ECSPI2_MOSI__ECSPI2_MOSI	0x1c0>,
+			   <MX8MP_IOMUXC_ECSPI2_SCLK__ECSPI2_SCLK	0x1c0>,
+			   <MX8MP_IOMUXC_ECSPI2_SS0__GPIO5_IO13		0x1c0>;
+	};
+
+	pinctrl_ecspi3: ecspi3grp {
+		fsl,pins = <MX8MP_IOMUXC_UART1_TXD__ECSPI3_MOSI		0x1c0>,
+			   <MX8MP_IOMUXC_UART1_RXD__ECSPI3_SCLK		0x1c0>,
+			   <MX8MP_IOMUXC_UART2_RXD__ECSPI3_MISO		0x1c0>,
+			   <MX8MP_IOMUXC_UART2_TXD__GPIO5_IO25		0x1c0>;
+	};
+
+	pinctrl_eqos: eqosgrp {
+		fsl,pins = <MX8MP_IOMUXC_ENET_MDC__ENET_QOS_MDC				0x40000044>,
+			   <MX8MP_IOMUXC_ENET_MDIO__ENET_QOS_MDIO			0x40000044>,
+			   <MX8MP_IOMUXC_ENET_RD0__ENET_QOS_RGMII_RD0			0x90>,
+			   <MX8MP_IOMUXC_ENET_RD1__ENET_QOS_RGMII_RD1			0x90>,
+			   <MX8MP_IOMUXC_ENET_RD2__ENET_QOS_RGMII_RD2			0x90>,
+			   <MX8MP_IOMUXC_ENET_RD3__ENET_QOS_RGMII_RD3			0x90>,
+			   <MX8MP_IOMUXC_ENET_RXC__CCM_ENET_QOS_CLOCK_GENERATE_RX_CLK	0x90>,
+			   <MX8MP_IOMUXC_ENET_RX_CTL__ENET_QOS_RGMII_RX_CTL		0x90>,
+			   <MX8MP_IOMUXC_ENET_TD0__ENET_QOS_RGMII_TD0			0x12>,
+			   <MX8MP_IOMUXC_ENET_TD1__ENET_QOS_RGMII_TD1			0x12>,
+			   <MX8MP_IOMUXC_ENET_TD2__ENET_QOS_RGMII_TD2			0x12>,
+			   <MX8MP_IOMUXC_ENET_TD3__ENET_QOS_RGMII_TD3			0x12>,
+			   <MX8MP_IOMUXC_ENET_TX_CTL__ENET_QOS_RGMII_TX_CTL		0x12>,
+			   <MX8MP_IOMUXC_ENET_TXC__CCM_ENET_QOS_CLOCK_GENERATE_TX_CLK	0x14>;
+	};
+
+	pinctrl_eqos_event: eqosevtgrp {
+		fsl,pins = <MX8MP_IOMUXC_SAI2_RXD0__ENET_QOS_1588_EVENT2_OUT		0x100>,
+			   <MX8MP_IOMUXC_SAI2_TXD0__ENET_QOS_1588_EVENT2_IN		0x1c0>;
+	};
+
+	pinctrl_eqos_phy: eqosphygrp {
+		fsl,pins = <MX8MP_IOMUXC_SAI1_RXD0__GPIO4_IO02				0x100>,
+			   <MX8MP_IOMUXC_SAI1_RXD1__GPIO4_IO03				0x1c0>;
+	};
+
+	pinctrl_fec: fecgrp {
+		fsl,pins = <MX8MP_IOMUXC_SAI1_RXD2__ENET1_MDC		0x40000044>,
+			   <MX8MP_IOMUXC_SAI1_RXD3__ENET1_MDIO		0x40000044>,
+			   <MX8MP_IOMUXC_SAI1_RXD4__ENET1_RGMII_RD0	0x90>,
+			   <MX8MP_IOMUXC_SAI1_RXD5__ENET1_RGMII_RD1	0x90>,
+			   <MX8MP_IOMUXC_SAI1_RXD6__ENET1_RGMII_RD2	0x90>,
+			   <MX8MP_IOMUXC_SAI1_RXD7__ENET1_RGMII_RD3	0x90>,
+			   <MX8MP_IOMUXC_SAI1_TXC__ENET1_RGMII_RXC	0x90>,
+			   <MX8MP_IOMUXC_SAI1_TXFS__ENET1_RGMII_RX_CTL	0x90>,
+			   <MX8MP_IOMUXC_SAI1_TXD0__ENET1_RGMII_TD0	0x12>,
+			   <MX8MP_IOMUXC_SAI1_TXD1__ENET1_RGMII_TD1	0x12>,
+			   <MX8MP_IOMUXC_SAI1_TXD2__ENET1_RGMII_TD2	0x12>,
+			   <MX8MP_IOMUXC_SAI1_TXD3__ENET1_RGMII_TD3	0x12>,
+			   <MX8MP_IOMUXC_SAI1_TXD4__ENET1_RGMII_TX_CTL	0x12>,
+			   <MX8MP_IOMUXC_SAI1_TXD5__ENET1_RGMII_TXC	0x14>;
+	};
+
+	pinctrl_fec_event: fecevtgrp {
+		fsl,pins = <MX8MP_IOMUXC_SAI1_RXFS__ENET1_1588_EVENT0_IN	0x100>,
+			   <MX8MP_IOMUXC_SAI1_RXC__ENET1_1588_EVENT0_OUT	0x1c0>;
+	};
+
+	pinctrl_fec_phy: fecphygrp {
+		fsl,pins = <MX8MP_IOMUXC_SAI1_RXFS__GPIO4_IO00		0x100>,
+			   <MX8MP_IOMUXC_SAI1_RXC__GPIO4_IO01		0x1c0>;
+	};
+
+	pinctrl_fec_phyalt: fecphyaltgrp {
+		fsl,pins = <MX8MP_IOMUXC_SAI2_TXFS__GPIO4_IO24		0x180>,
+			   <MX8MP_IOMUXC_SAI2_TXC__GPIO4_IO25		0x180>;
+	};
+
+	pinctrl_gpiobutton: gpiobuttongrp {
+		fsl,pins = <MX8MP_IOMUXC_UART3_RXD__GPIO5_IO26		0x10>,
+			   <MX8MP_IOMUXC_UART3_TXD__GPIO5_IO27		0x10>;
+	};
+
+	pinctrl_gpioled: gpioledgrp {
+		fsl,pins = <MX8MP_IOMUXC_SPDIF_EXT_CLK__GPIO5_IO05	0x14>,
+			   <MX8MP_IOMUXC_SPDIF_RX__GPIO5_IO04		0x14>,
+			   <MX8MP_IOMUXC_SPDIF_TX__GPIO5_IO03		0x14>;
+	};
+
+	pinctrl_gpio1: gpio1grp {
+		fsl,pins = <MX8MP_IOMUXC_GPIO1_IO00__GPIO1_IO00		0x10>,
+			   <MX8MP_IOMUXC_GPIO1_IO01__GPIO1_IO01		0x10>,
+			   <MX8MP_IOMUXC_GPIO1_IO03__GPIO1_IO03		0x10>,
+			   <MX8MP_IOMUXC_GPIO1_IO06__GPIO1_IO06		0x10>,
+			   <MX8MP_IOMUXC_GPIO1_IO07__GPIO1_IO07		0x80>,
+			   <MX8MP_IOMUXC_GPIO1_IO09__GPIO1_IO09		0x80>,
+			   <MX8MP_IOMUXC_GPIO1_IO14__GPIO1_IO14		0x80>,
+			   <MX8MP_IOMUXC_GPIO1_IO15__GPIO1_IO15		0x80>;
+	};
+
+	pinctrl_gpio4: gpio4grp {
+		fsl,pins = <MX8MP_IOMUXC_SAI1_MCLK__GPIO4_IO20		0x180>,
+			   <MX8MP_IOMUXC_SAI2_RXC__GPIO4_IO22		0x180>;
+	};
+
+	pinctrl_hdmi: hdmigrp {
+		fsl,pins = <MX8MP_IOMUXC_HDMI_DDC_SCL__HDMIMIX_HDMI_SCL	0x400001c2>,
+			   <MX8MP_IOMUXC_HDMI_DDC_SDA__HDMIMIX_HDMI_SDA	0x400001c2>,
+			   <MX8MP_IOMUXC_HDMI_HPD__HDMIMIX_HDMI_HPD	0x40000010>,
+			   <MX8MP_IOMUXC_HDMI_CEC__HDMIMIX_HDMI_CEC	0x40000010>;
+	};
+
+	pinctrl_hoggpio2: hoggpio2grp {
+		fsl,pins = <MX8MP_IOMUXC_SD1_DATA5__GPIO2_IO07		0x140>,
+			   <MX8MP_IOMUXC_SD1_RESET_B__GPIO2_IO10	0x140>,
+			   <MX8MP_IOMUXC_SD1_STROBE__GPIO2_IO11		0x140>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <MX8MP_IOMUXC_I2C2_SCL__I2C2_SCL		0x400001e2>,
+			   <MX8MP_IOMUXC_I2C2_SDA__I2C2_SDA		0x400001e2>;
+	};
+
+	pinctrl_i2c2_gpio: i2c2-gpiogrp {
+		fsl,pins = <MX8MP_IOMUXC_I2C2_SCL__GPIO5_IO16		0x400001e2>,
+			   <MX8MP_IOMUXC_I2C2_SDA__GPIO5_IO17		0x400001e2>;
+	};
+
+	pinctrl_i2c4: i2c4grp {
+		fsl,pins = <MX8MP_IOMUXC_I2C4_SCL__I2C4_SCL		0x400001e2>,
+			   <MX8MP_IOMUXC_I2C4_SDA__I2C4_SDA		0x400001e2>;
+	};
+
+	pinctrl_i2c4_gpio: i2c4-gpiogrp {
+		fsl,pins = <MX8MP_IOMUXC_I2C4_SCL__GPIO5_IO20		0x400001e2>,
+			   <MX8MP_IOMUXC_I2C4_SDA__GPIO5_IO21		0x400001e2>;
+	};
+
+	pinctrl_i2c6: i2c6grp {
+		fsl,pins = <MX8MP_IOMUXC_SD1_DATA0__I2C6_SCL		0x400001e2>,
+			   <MX8MP_IOMUXC_SD1_DATA1__I2C6_SDA		0x400001e2>;
+	};
+
+	pinctrl_i2c6_gpio: i2c6-gpiogrp {
+		fsl,pins = <MX8MP_IOMUXC_SD1_DATA0__GPIO2_IO02		0x400001e2>,
+			   <MX8MP_IOMUXC_SD1_DATA1__GPIO2_IO03		0x400001e2>;
+	};
+
+	pinctrl_lvdsdisplay: lvdsdisplaygrp {
+		fsl,pins = <MX8MP_IOMUXC_SAI5_RXC__GPIO3_IO20		0x10>; /* Power enable */
+	};
+
+	pinctrl_pcf85063: pcf85063grp {
+		fsl,pins = <MX8MP_IOMUXC_SAI3_RXFS__GPIO4_IO28		0x80>;
+	};
+
+	/* LVDS Backlight */
+	pinctrl_pwm2: pwm2grp {
+		fsl,pins = <MX8MP_IOMUXC_SAI5_RXD0__PWM2_OUT		0x14>;
+	};
+
+	/* FAN */
+	pinctrl_pwm3: pwm3grp {
+		fsl,pins = <MX8MP_IOMUXC_I2C3_SDA__PWM3_OUT		0x14>;
+	};
+
+	pinctrl_reg12v0: reg12v0grp {
+		fsl,pins = <MX8MP_IOMUXC_SD1_DATA4__GPIO2_IO06		0x140>; /* VCC12V enable */
+	};
+
+	/* X61 */
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <MX8MP_IOMUXC_SD1_CLK__UART1_DCE_TX		0x140>,
+			   <MX8MP_IOMUXC_SD1_CMD__UART1_DCE_RX		0x140>;
+	};
+
+	/* X61 */
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <MX8MP_IOMUXC_SD1_DATA2__UART2_DCE_TX	0x140>,
+			   <MX8MP_IOMUXC_SD1_DATA3__UART2_DCE_RX	0x140>;
+	};
+
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <MX8MP_IOMUXC_SD1_DATA6__UART3_DCE_TX	0x140>,
+			   <MX8MP_IOMUXC_SD1_DATA7__UART3_DCE_RX	0x140>;
+	};
+
+	pinctrl_uart4: uart4grp {
+		fsl,pins = <MX8MP_IOMUXC_UART4_RXD__UART4_DCE_RX	0x140>,
+			   <MX8MP_IOMUXC_UART4_TXD__UART4_DCE_TX	0x140>;
+	};
+
+	pinctrl_usb0: usb0grp {
+		fsl,pins = <MX8MP_IOMUXC_GPIO1_IO13__USB1_OTG_OC	0x1c0>,
+			   <MX8MP_IOMUXC_GPIO1_IO12__USB1_OTG_PWR	0x1c0>;
+	};
+
+	pinctrl_usbcon0: usb0congrp {
+		fsl,pins = <MX8MP_IOMUXC_GPIO1_IO10__GPIO1_IO10		0x1c0>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK		0x192>,
+			   <MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD		0x1d2>,
+			   <MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0	0x1d2>,
+			   <MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1	0x1d2>,
+			   <MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2	0x1d2>,
+			   <MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3	0x1d2>,
+			   <MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT	0xc0>;
+	};
+
+	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+		fsl,pins = <MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK		0x194>,
+			   <MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD		0x1d4>,
+			   <MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0	0x1d4>,
+			   <MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1	0x1d4>,
+			   <MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2	0x1d4>,
+			   <MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3	0x1d4>,
+			   <MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT	0xc0>;
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+		fsl,pins = <MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK		0x194>,
+			   <MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD		0x1d4>,
+			   <MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0	0x1d4>,
+			   <MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1	0x1d4>,
+			   <MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2	0x1d4>,
+			   <MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3	0x1d4>,
+			   <MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT	0xc0>;
+	};
+
+	pinctrl_usdhc2_gpio: usdhc2-gpiogrp {
+		fsl,pins = <MX8MP_IOMUXC_SD2_CD_B__GPIO2_IO12		0x1c0>;
+	};
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mp-tqma8mpql.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-tqma8mpql.dtsi
new file mode 100644
index 000000000000..7bd680a926ce
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mp-tqma8mpql.dtsi
@@ -0,0 +1,284 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2021-2022 TQ-Systems GmbH
+ * Author: Alexander Stein <alexander.stein@tq-group.com>
+ */
+
+#include "imx8mp.dtsi"
+
+/ {
+	model = "TQ-Systems i.MX8MPlus TQMa8MPxL";
+	compatible = "tq,imx8mp-tqma8mpql", "fsl,imx8mp";
+
+	memory@40000000 {
+		device_type = "memory";
+		reg = <0x0 0x40000000 0 0x80000000>;
+	};
+
+	/* identical to buck4_reg, but should never change */
+	reg_vcc3v3: regulator-vcc3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	/* e-MMC IO, needed for HS modes */
+	reg_vcc1v8: regulator-vcc1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
+	};
+};
+
+&A53_0 {
+	cpu-supply = <&buck2_reg>;
+};
+
+&flexspi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexspi0>;
+	status = "okay";
+
+	flash0: flash@0 {
+		reg = <0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "jedec,spi-nor";
+		spi-max-frequency = <80000000>;
+		spi-tx-bus-width = <1>;
+		spi-rx-bus-width = <4>;
+	};
+};
+
+&i2c1 {
+	clock-frequency = <384000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	pinctrl-1 = <&pinctrl_i2c1_gpio>;
+	scl-gpios = <&gpio5 14 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio5 15 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "okay";
+
+	/* NXP SE97BTP with temperature sensor + eeprom */
+	se97: temperature-sensor-eeprom@1b {
+		compatible = "nxp,se97", "jedec,jc-42.4-temp";
+		reg = <0x1b>;
+	};
+
+	pmic: pmic@25 {
+		reg = <0x25>;
+		compatible = "nxp,pca9450c";
+
+		/* PMIC PCA9450 PMIC_nINT GPIO1_IO08 */
+		pinctrl-0 = <&pinctrl_pmic>;
+		pinctrl-names = "default";
+		interrupt-parent = <&gpio1>;
+		interrupts = <8 IRQ_TYPE_LEVEL_LOW>;
+
+		regulators {
+			/* V_0V85_SOC: 0.85 .. 0.95 */
+			buck1_reg: BUCK1 {
+				regulator-name = "BUCK1";
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <950000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <3125>;
+			};
+
+			/* VDD_ARM */
+			buck2_reg: BUCK2 {
+				regulator-name = "BUCK2";
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-boot-on;
+				regulator-always-on;
+				nxp,dvs-run-voltage = <950000>;
+				nxp,dvs-standby-voltage = <850000>;
+				regulator-ramp-delay = <3125>;
+			};
+
+			/* VCC3V3 -> VMMC, ... must not be changed */
+			buck4_reg: BUCK4 {
+				regulator-name = "BUCK4";
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			/* V_1V8 -> VQMMC, SPI-NOR, ... must not be changed */
+			buck5_reg: BUCK5 {
+				regulator-name = "BUCK5";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			/* V_1V1 -> RAM, ... must not be changed */
+			buck6_reg: BUCK6 {
+				regulator-name = "BUCK6";
+				regulator-min-microvolt = <1100000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			/* V_1V8_SNVS */
+			ldo1_reg: LDO1 {
+				regulator-name = "LDO1";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			/* V_1V8_ANA */
+			ldo3_reg: LDO3 {
+				regulator-name = "LDO3";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			/* unused */
+			ldo4_reg: LDO4 {
+				regulator-name = "LDO4";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			/* VCC SD IO - switched using SD2 VSELECT */
+			ldo5_reg: LDO5 {
+				regulator-name = "LDO5";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+			};
+		};
+	};
+
+	pcf85063: rtc@51 {
+		compatible = "nxp,pcf85063a";
+		reg = <0x51>;
+	};
+
+	at24c02: eeprom@53 {
+		compatible = "nxp,se97b", "atmel,24c02";
+		read-only;
+		reg = <0x53>;
+		pagesize = <16>;
+		vcc-supply = <&reg_vcc3v3>;
+	};
+
+	m24c64: eeprom@57 {
+		compatible = "atmel,24c64";
+		reg = <0x57>;
+		pagesize = <32>;
+		vcc-supply = <&reg_vcc3v3>;
+	};
+};
+
+&usdhc3 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+	bus-width = <8>;
+	non-removable;
+	no-sd;
+	no-sdio;
+	vmmc-supply = <&reg_vcc3v3>;
+	vqmmc-supply = <&reg_vcc1v8>;
+	status = "okay";
+};
+
+&wdog1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog>;
+	fsl,ext-reset-output;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_flexspi0: flexspi0grp {
+		fsl,pins = <MX8MP_IOMUXC_NAND_ALE__FLEXSPI_A_SCLK	0x142>,
+			   <MX8MP_IOMUXC_NAND_CE0_B__FLEXSPI_A_SS0_B	0x82>,
+			   <MX8MP_IOMUXC_NAND_DATA00__FLEXSPI_A_DATA00	0x82>,
+			   <MX8MP_IOMUXC_NAND_DATA01__FLEXSPI_A_DATA01	0x82>,
+			   <MX8MP_IOMUXC_NAND_DATA02__FLEXSPI_A_DATA02	0x82>,
+			   <MX8MP_IOMUXC_NAND_DATA03__FLEXSPI_A_DATA03	0x82>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <MX8MP_IOMUXC_I2C1_SCL__I2C1_SCL		0x400001e2>,
+			   <MX8MP_IOMUXC_I2C1_SDA__I2C1_SDA		0x400001e2>;
+	};
+
+	pinctrl_i2c1_gpio: i2c1-gpiogrp {
+		fsl,pins = <MX8MP_IOMUXC_I2C1_SCL__GPIO5_IO14		0x400001e2>,
+			   <MX8MP_IOMUXC_I2C1_SDA__GPIO5_IO15		0x400001e2>;
+	};
+
+	pinctrl_pmic: pmicirqgrp {
+		fsl,pins = <MX8MP_IOMUXC_GPIO1_IO08__GPIO1_IO08		0x1c0>;
+	};
+
+	pinctrl_reg_usdhc2_vmmc: regusdhc2vmmcgrp {
+		fsl,pins = <MX8MP_IOMUXC_SD2_RESET_B__GPIO2_IO19	0x10>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK		0x194>,
+			   <MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD		0x1d4>,
+			   <MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0	0x1d4>,
+			   <MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1	0x1d4>,
+			   <MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2	0x1d4>,
+			   <MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3	0x1d4>,
+			   <MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4	0x1d4>,
+			   <MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5	0x1d4>,
+			   <MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6	0x1d4>,
+			   <MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7		0x1d4>,
+			   <MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE	0x84>,
+			   <MX8MP_IOMUXC_NAND_READY_B__USDHC3_RESET_B	0x84>;
+	};
+
+	pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
+		fsl,pins = <MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK		0x194>,
+			   <MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD		0x1d4>,
+			   <MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0	0x1d4>,
+			   <MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1	0x1d4>,
+			   <MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2	0x1d4>,
+			   <MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3	0x1d4>,
+			   <MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4	0x1d4>,
+			   <MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5	0x1d4>,
+			   <MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6	0x1d4>,
+			   <MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7		0x1d4>,
+			   <MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE	0x84>,
+			   <MX8MP_IOMUXC_NAND_READY_B__USDHC3_RESET_B	0x84>;
+	};
+
+	pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
+		fsl,pins = <MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK		0x194>,
+			   <MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD		0x1d4>,
+			   <MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0	0x1d4>,
+			   <MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1	0x1d4>,
+			   <MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2	0x1d4>,
+			   <MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3	0x1d4>,
+			   <MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4	0x1d4>,
+			   <MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5	0x1d4>,
+			   <MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6	0x1d4>,
+			   <MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7		0x1d4>,
+			   <MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE	0x84>,
+			   <MX8MP_IOMUXC_NAND_READY_B__USDHC3_RESET_B	0x84>;
+	};
+
+	pinctrl_wdog: wdoggrp {
+		fsl,pins = <MX8MP_IOMUXC_GPIO1_IO02__WDOG1_WDOG_B	0x1c4>;
+	};
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mp-venice-gw74xx.dts b/arch/arm64/boot/dts/freescale/imx8mp-venice-gw74xx.dts
new file mode 100644
index 000000000000..06b4c93c5876
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mp-venice-gw74xx.dts
@@ -0,0 +1,1026 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2021 Gateworks Corporation
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/phy/phy-imx8-pcie.h>
+
+#include "imx8mp.dtsi"
+
+/ {
+	model = "Gateworks Venice GW74xx i.MX8MP board";
+	compatible = "gateworks,imx8mp-gw74xx", "fsl,imx8mp";
+
+	aliases {
+		ethernet0 = &eqos;
+		ethernet1 = &fec;
+		ethernet2 = &lan1;
+		ethernet3 = &lan2;
+		ethernet4 = &lan3;
+		ethernet5 = &lan4;
+		ethernet6 = &lan5;
+	};
+
+	chosen {
+		stdout-path = &uart2;
+	};
+
+	memory@40000000 {
+		device_type = "memory";
+		reg = <0x0 0x40000000 0 0x80000000>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		key-0 {
+			label = "user_pb";
+			gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
+			linux,code = <BTN_0>;
+		};
+
+		key-1 {
+			label = "user_pb1x";
+			linux,code = <BTN_1>;
+			interrupt-parent = <&gsc>;
+			interrupts = <0>;
+		};
+
+		key-2 {
+			label = "key_erased";
+			linux,code = <BTN_2>;
+			interrupt-parent = <&gsc>;
+			interrupts = <1>;
+		};
+
+		key-3 {
+			label = "eeprom_wp";
+			linux,code = <BTN_3>;
+			interrupt-parent = <&gsc>;
+			interrupts = <2>;
+		};
+
+		key-4 {
+			label = "tamper";
+			linux,code = <BTN_4>;
+			interrupt-parent = <&gsc>;
+			interrupts = <5>;
+		};
+
+		key-5 {
+			label = "switch_hold";
+			linux,code = <BTN_5>;
+			interrupt-parent = <&gsc>;
+			interrupts = <7>;
+		};
+	};
+
+	led-controller {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_leds>;
+
+		led-0 {
+			function = LED_FUNCTION_HEARTBEAT;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&gpio2 15 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+			linux,default-trigger = "heartbeat";
+		};
+
+		led-1 {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_RED>;
+			gpios = <&gpio2 16 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+	};
+
+	pcie0_refclk: pcie0-refclk {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <100000000>;
+	};
+
+	pps {
+		compatible = "pps-gpio";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_pps>;
+		gpios = <&gpio1 12 GPIO_ACTIVE_HIGH>;
+	};
+
+	reg_usb2_vbus: regulator-usb2 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_usb2>;
+		compatible = "regulator-fixed";
+		regulator-name = "usb_usb2_vbus";
+		gpio = <&gpio1 6 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	reg_can2_stby: regulator-can2-stby {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_can>;
+		regulator-name = "can2_stby";
+		gpio = <&gpio3 19 GPIO_ACTIVE_LOW>;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	reg_wifi_en: regulator-wifi-en {
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_wifi>;
+		compatible = "regulator-fixed";
+		regulator-name = "wl";
+		gpio = <&gpio3 9 GPIO_ACTIVE_HIGH>;
+		startup-delay-us = <70000>;
+		enable-active-high;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+};
+
+&A53_0 {
+	cpu-supply = <&reg_arm>;
+};
+
+&A53_1 {
+	cpu-supply = <&reg_arm>;
+};
+
+&A53_2 {
+	cpu-supply = <&reg_arm>;
+};
+
+&A53_3 {
+	cpu-supply = <&reg_arm>;
+};
+
+/* off-board header */
+&ecspi2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_spi2>;
+	cs-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&eqos {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_eqos>;
+	phy-mode = "rgmii-id";
+	phy-handle = <&ethphy0>;
+	status = "okay";
+
+	mdio {
+		compatible = "snps,dwmac-mdio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy0: ethernet-phy@0 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <0x0>;
+		};
+	};
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_fec>;
+	phy-mode = "rgmii-id";
+	local-mac-address = [00 00 00 00 00 00];
+	status = "okay";
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+};
+
+&flexcan2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan2>;
+	xceiver-supply = <&reg_can2_stby>;
+	status = "okay";
+};
+
+&gpio1 {
+	gpio-line-names =
+		"", "", "", "", "", "", "", "",
+		"", "", "dio0", "", "dio1", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "";
+};
+
+&gpio2 {
+	gpio-line-names =
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "pcie3_wdis#", "",
+		"", "", "pcie2_wdis#", "", "", "", "", "",
+		"", "", "", "", "", "", "", "";
+};
+
+&gpio3 {
+	gpio-line-names =
+		"m2_gdis#", "", "", "", "", "", "", "m2_rst#",
+		"", "", "", "", "", "", "", "",
+		"m2_off#", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "";
+};
+
+&gpio4 {
+	gpio-line-names =
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "m2_wdis#", "", "", "",
+		"", "", "", "", "", "", "", "uart_rs485";
+};
+
+&gpio5 {
+	gpio-line-names =
+		"uart_half", "uart_term", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "", "";
+};
+
+&i2c1 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+
+	gsc: gsc@20 {
+		compatible = "gw,gsc";
+		reg = <0x20>;
+		pinctrl-0 = <&pinctrl_gsc>;
+		interrupt-parent = <&gpio4>;
+		interrupts = <20 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-controller;
+		#interrupt-cells = <1>;
+
+		adc {
+			compatible = "gw,gsc-adc";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			channel@6 {
+				gw,mode = <0>;
+				reg = <0x06>;
+				label = "temp";
+			};
+
+			channel@8 {
+				gw,mode = <1>;
+				reg = <0x08>;
+				label = "vdd_bat";
+			};
+
+			channel@82 {
+				gw,mode = <2>;
+				reg = <0x82>;
+				label = "vdd_adc1";
+				gw,voltage-divider-ohms = <10000 10000>;
+			};
+
+			channel@84 {
+				gw,mode = <2>;
+				reg = <0x84>;
+				label = "vdd_adc2";
+				gw,voltage-divider-ohms = <10000 10000>;
+			};
+
+			channel@86 {
+				gw,mode = <2>;
+				reg = <0x86>;
+				label = "vdd_vin";
+				gw,voltage-divider-ohms = <22100 1000>;
+			};
+
+			channel@88 {
+				gw,mode = <2>;
+				reg = <0x88>;
+				label = "vdd_3p3";
+				gw,voltage-divider-ohms = <10000 10000>;
+			};
+
+			channel@8c {
+				gw,mode = <2>;
+				reg = <0x8c>;
+				label = "vdd_2p5";
+				gw,voltage-divider-ohms = <10000 10000>;
+			};
+
+			channel@90 {
+				gw,mode = <2>;
+				reg = <0x90>;
+				label = "vdd_soc";
+			};
+
+			channel@92 {
+				gw,mode = <2>;
+				reg = <0x92>;
+				label = "vdd_arm";
+			};
+
+			channel@98 {
+				gw,mode = <2>;
+				reg = <0x98>;
+				label = "vdd_1p8";
+			};
+
+			channel@9a {
+				gw,mode = <2>;
+				reg = <0x9a>;
+				label = "vdd_1p2";
+			};
+
+			channel@9c {
+				gw,mode = <2>;
+				reg = <0x9c>;
+				label = "vdd_dram";
+			};
+
+			channel@a2 {
+				gw,mode = <2>;
+				reg = <0xa2>;
+				label = "vdd_gsc";
+				gw,voltage-divider-ohms = <10000 10000>;
+			};
+		};
+	};
+
+	gpio: gpio@23 {
+		compatible = "nxp,pca9555";
+		reg = <0x23>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-parent = <&gsc>;
+		interrupts = <4>;
+	};
+
+	pmic@25 {
+		compatible = "nxp,pca9450c";
+		reg = <0x25>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_pmic>;
+		interrupt-parent = <&gpio3>;
+		interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
+
+		regulators {
+			BUCK1 {
+				regulator-name = "BUCK1";
+				regulator-min-microvolt = <720000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <3125>;
+			};
+
+			reg_arm: BUCK2 {
+				regulator-name = "BUCK2";
+				regulator-min-microvolt = <720000>;
+				regulator-max-microvolt = <1025000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-ramp-delay = <3125>;
+				nxp,dvs-run-voltage = <950000>;
+				nxp,dvs-standby-voltage = <850000>;
+			};
+
+			BUCK4 {
+				regulator-name = "BUCK4";
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3600000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			BUCK5 {
+				regulator-name = "BUCK5";
+				regulator-min-microvolt = <1650000>;
+				regulator-max-microvolt = <1950000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			BUCK6 {
+				regulator-name = "BUCK6";
+				regulator-min-microvolt = <1045000>;
+				regulator-max-microvolt = <1155000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			LDO1 {
+				regulator-name = "LDO1";
+				regulator-min-microvolt = <1650000>;
+				regulator-max-microvolt = <1950000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			LDO3 {
+				regulator-name = "LDO3";
+				regulator-min-microvolt = <1710000>;
+				regulator-max-microvolt = <1890000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			LDO5 {
+				regulator-name = "LDO5";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-boot-on;
+				regulator-always-on;
+			};
+		};
+	};
+
+	eeprom@50 {
+		compatible = "atmel,24c02";
+		reg = <0x50>;
+		pagesize = <16>;
+	};
+
+	eeprom@51 {
+		compatible = "atmel,24c02";
+		reg = <0x51>;
+		pagesize = <16>;
+	};
+
+	eeprom@52 {
+		compatible = "atmel,24c02";
+		reg = <0x52>;
+		pagesize = <16>;
+	};
+
+	eeprom@53 {
+		compatible = "atmel,24c02";
+		reg = <0x53>;
+		pagesize = <16>;
+	};
+
+	rtc@68 {
+		compatible = "dallas,ds1672";
+		reg = <0x68>;
+	};
+};
+
+&i2c2 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	status = "okay";
+
+	accelerometer@19 {
+		compatible = "st,lis2de12";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_accel>;
+		reg = <0x19>;
+		st,drdy-int-pin = <1>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-names = "INT1";
+	};
+
+	switch: switch@5f {
+		compatible = "microchip,ksz9897";
+		reg = <0x5f>;
+		pinctrl-0 = <&pinctrl_ksz>;
+		interrupt-parent = <&gpio4>;
+		interrupts = <29 IRQ_TYPE_EDGE_FALLING>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			lan1: port@0 {
+				reg = <0>;
+				label = "lan1";
+				phy-mode = "internal";
+				local-mac-address = [00 00 00 00 00 00];
+			};
+
+			lan2: port@1 {
+				reg = <1>;
+				label = "lan2";
+				phy-mode = "internal";
+				local-mac-address = [00 00 00 00 00 00];
+			};
+
+			lan3: port@2 {
+				reg = <2>;
+				label = "lan3";
+				phy-mode = "internal";
+				local-mac-address = [00 00 00 00 00 00];
+			};
+
+			lan4: port@3 {
+				reg = <3>;
+				label = "lan4";
+				phy-mode = "internal";
+				local-mac-address = [00 00 00 00 00 00];
+			};
+
+			lan5: port@4 {
+				reg = <4>;
+				label = "lan5";
+				phy-mode = "internal";
+				local-mac-address = [00 00 00 00 00 00];
+			};
+
+			port@5 {
+				reg = <5>;
+				label = "cpu";
+				ethernet = <&fec>;
+				phy-mode = "rgmii-id";
+
+				fixed-link {
+					speed = <1000>;
+					full-duplex;
+				};
+			};
+		};
+	};
+};
+
+/* off-board header */
+&i2c3 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "okay";
+};
+
+/* off-board header */
+&i2c4 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c4>;
+	status = "okay";
+};
+
+&pcie_phy {
+	fsl,refclk-pad-mode = <IMX8_PCIE_REFCLK_PAD_INPUT>;
+	fsl,clkreq-unsupported;
+	clocks = <&pcie0_refclk>;
+	clock-names = "ref";
+	status = "okay";
+};
+
+&pcie {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pcie0>;
+	reset-gpio = <&gpio2 17 GPIO_ACTIVE_LOW>;
+	clocks = <&clk IMX8MP_CLK_HSIO_ROOT>,
+		 <&clk IMX8MP_CLK_PCIE_ROOT>,
+		 <&clk IMX8MP_CLK_HSIO_AXI>;
+	clock-names = "pcie", "pcie_aux", "pcie_bus";
+	assigned-clocks = <&clk IMX8MP_CLK_PCIE_AUX>;
+	assigned-clock-rates = <10000000>;
+	assigned-clock-parents = <&clk IMX8MP_SYS_PLL2_50M>;
+	status = "okay";
+};
+
+/* GPS / off-board header */
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+/* RS232 console */
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	status = "okay";
+};
+
+/* bluetooth HCI */
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>, <&pinctrl_uart3_gpio>;
+	cts-gpios = <&gpio3 21 GPIO_ACTIVE_LOW>;
+	rts-gpios = <&gpio3 22 GPIO_ACTIVE_LOW>;
+	uart-has-rtscts;
+	status = "okay";
+
+	bluetooth {
+		compatible = "brcm,bcm4330-bt";
+		shutdown-gpios = <&gpio3 8 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+	status = "okay";
+};
+
+/* USB1 - Type C front panel */
+&usb3_0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb1>;
+	fsl,over-current-active-low;
+	status = "okay";
+};
+
+&usb3_phy0 {
+	status = "okay";
+};
+
+&usb_dwc3_0 {
+	/* dual role is implemented but not a full featured OTG */
+	adp-disable;
+	hnp-disable;
+	srp-disable;
+	dr_mode = "otg";
+	usb-role-switch;
+	role-switch-default-mode = "peripheral";
+	status = "okay";
+
+	connector {
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usbcon1>;
+		compatible = "gpio-usb-b-connector", "usb-b-connector";
+		type = "micro";
+		label = "Type-C";
+		id-gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+/* USB2 - USB3.0 Hub */
+&usb3_phy1 {
+	vbus-supply = <&reg_usb2_vbus>;
+	status = "okay";
+};
+
+&usb3_1 {
+	fsl,permanently-attached;
+	fsl,disable-port-power-control;
+	status = "okay";
+};
+
+&usb_dwc3_1 {
+	dr_mode = "host";
+	status = "okay";
+};
+
+/* SDIO WiFi */
+&usdhc1 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
+	bus-width = <4>;
+	non-removable;
+	vmmc-supply = <&reg_wifi_en>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	wifi@0 {
+		compatible = "cypress,cyw4373-fmac";
+		reg = <0>;
+	};
+};
+
+/* eMMC */
+&usdhc3 {
+	assigned-clocks = <&clk IMX8MP_CLK_USDHC3>;
+	assigned-clock-rates = <400000000>;
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+	bus-width = <8>;
+	non-removable;
+	status = "okay";
+};
+
+&wdog1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog>;
+	fsl,ext-reset-output;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hog>;
+
+	pinctrl_hog: hoggrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_GPIO1_IO09__GPIO1_IO09	0x40000040 /* DIO0 */
+			MX8MP_IOMUXC_GPIO1_IO11__GPIO1_IO11	0x40000040 /* DIO1 */
+			MX8MP_IOMUXC_NAND_DQS__GPIO3_IO14	0x40000040 /* M2SKT_OFF# */
+			MX8MP_IOMUXC_SD2_DATA3__GPIO2_IO18	0x40000150 /* PCIE2_WDIS# */
+			MX8MP_IOMUXC_SD2_CMD__GPIO2_IO14	0x40000150 /* PCIE3_WDIS# */
+			MX8MP_IOMUXC_NAND_DATA00__GPIO3_IO06	0x40000040 /* M2SKT_RST# */
+			MX8MP_IOMUXC_SAI1_TXD6__GPIO4_IO18	0x40000150 /* M2SKT_WDIS# */
+			MX8MP_IOMUXC_NAND_ALE__GPIO3_IO00	0x40000150 /* M2SKT_GDIS# */
+			MX8MP_IOMUXC_SAI3_TXD__GPIO5_IO01	0x40000104 /* UART_TERM */
+			MX8MP_IOMUXC_SAI3_TXFS__GPIO4_IO31	0x40000104 /* UART_RS485 */
+			MX8MP_IOMUXC_SAI3_TXC__GPIO5_IO00	0x40000104 /* UART_HALF */
+		>;
+	};
+
+	pinctrl_accel: accelgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_GPIO1_IO07__GPIO1_IO07	0x150
+		>;
+	};
+
+	pinctrl_eqos: eqosgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_ENET_MDC__ENET_QOS_MDC				0x2
+			MX8MP_IOMUXC_ENET_MDIO__ENET_QOS_MDIO				0x2
+			MX8MP_IOMUXC_ENET_RD0__ENET_QOS_RGMII_RD0		0x90
+			MX8MP_IOMUXC_ENET_RD1__ENET_QOS_RGMII_RD1		0x90
+			MX8MP_IOMUXC_ENET_RD2__ENET_QOS_RGMII_RD2		0x90
+			MX8MP_IOMUXC_ENET_RD3__ENET_QOS_RGMII_RD3		0x90
+			MX8MP_IOMUXC_ENET_RXC__CCM_ENET_QOS_CLOCK_GENERATE_RX_CLK	0x90
+			MX8MP_IOMUXC_ENET_RX_CTL__ENET_QOS_RGMII_RX_CTL		0x90
+			MX8MP_IOMUXC_ENET_TD0__ENET_QOS_RGMII_TD0		0x16
+			MX8MP_IOMUXC_ENET_TD1__ENET_QOS_RGMII_TD1		0x16
+			MX8MP_IOMUXC_ENET_TD2__ENET_QOS_RGMII_TD2		0x16
+			MX8MP_IOMUXC_ENET_TD3__ENET_QOS_RGMII_TD3		0x16
+			MX8MP_IOMUXC_ENET_TX_CTL__ENET_QOS_RGMII_TX_CTL		0x16
+			MX8MP_IOMUXC_ENET_TXC__CCM_ENET_QOS_CLOCK_GENERATE_TX_CLK	0x16
+			MX8MP_IOMUXC_SAI3_RXD__GPIO4_IO30		0x140 /* RST# */
+			MX8MP_IOMUXC_SAI3_RXFS__GPIO4_IO28		0x150 /* IRQ# */
+		>;
+	};
+
+	pinctrl_fec: fecgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SAI1_RXD4__ENET1_RGMII_RD0		0x90
+			MX8MP_IOMUXC_SAI1_RXD5__ENET1_RGMII_RD1		0x90
+			MX8MP_IOMUXC_SAI1_RXD6__ENET1_RGMII_RD2		0x90
+			MX8MP_IOMUXC_SAI1_RXD7__ENET1_RGMII_RD3		0x90
+			MX8MP_IOMUXC_SAI1_TXC__ENET1_RGMII_RXC		0x90
+			MX8MP_IOMUXC_SAI1_TXFS__ENET1_RGMII_RX_CTL	0x90
+			MX8MP_IOMUXC_SAI1_TXD0__ENET1_RGMII_TD0		0x16
+			MX8MP_IOMUXC_SAI1_TXD1__ENET1_RGMII_TD1		0x16
+			MX8MP_IOMUXC_SAI1_TXD2__ENET1_RGMII_TD2		0x16
+			MX8MP_IOMUXC_SAI1_TXD3__ENET1_RGMII_TD3		0x16
+			MX8MP_IOMUXC_SAI1_TXD4__ENET1_RGMII_TX_CTL	0x16
+			MX8MP_IOMUXC_SAI1_TXD5__ENET1_RGMII_TXC		0x16
+			MX8MP_IOMUXC_SAI1_RXFS__ENET1_1588_EVENT0_IN	0x140
+			MX8MP_IOMUXC_SAI1_RXC__ENET1_1588_EVENT0_OUT	0x140
+		>;
+	};
+
+	pinctrl_flexcan2: flexcan2grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SAI5_RXD3__CAN2_TX		0x154
+			MX8MP_IOMUXC_SAI5_MCLK__CAN2_RX		0x154
+		>;
+	};
+
+	pinctrl_gsc: gscgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SAI1_MCLK__GPIO4_IO20	0x150
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_I2C1_SCL__I2C1_SCL		0x400001c2
+			MX8MP_IOMUXC_I2C1_SDA__I2C1_SDA		0x400001c2
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_I2C2_SCL__I2C2_SCL		0x400001c2
+			MX8MP_IOMUXC_I2C2_SDA__I2C2_SDA		0x400001c2
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_I2C3_SCL__I2C3_SCL		0x400001c2
+			MX8MP_IOMUXC_I2C3_SDA__I2C3_SDA		0x400001c2
+		>;
+	};
+
+	pinctrl_i2c4: i2c4grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_I2C4_SCL__I2C4_SCL		0x400001c2
+			MX8MP_IOMUXC_I2C4_SDA__I2C4_SDA		0x400001c2
+		>;
+	};
+
+	pinctrl_ksz: kszgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SAI3_RXC__GPIO4_IO29	0x150 /* IRQ# */
+			MX8MP_IOMUXC_SAI3_MCLK__GPIO5_IO02	0x140 /* RST# */
+		>;
+	};
+
+	pinctrl_gpio_leds: ledgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SD2_DATA0__GPIO2_IO15	0x10
+			MX8MP_IOMUXC_SD2_DATA1__GPIO2_IO16	0x10
+		>;
+	};
+
+	pinctrl_pcie0: pciegrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SD2_DATA2__GPIO2_IO17	0x110
+		>;
+	};
+
+	pinctrl_pmic: pmicgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_NAND_DATA01__GPIO3_IO07	0x140
+		>;
+	};
+
+	pinctrl_pps: ppsgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_GPIO1_IO12__GPIO1_IO12	0x140
+		>;
+	};
+
+	pinctrl_reg_can: regcangrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SAI5_RXFS__GPIO3_IO19	0x154
+		>;
+	};
+
+	pinctrl_reg_usb2: regusb2grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_GPIO1_IO06__GPIO1_IO06	0x140
+		>;
+	};
+
+	pinctrl_reg_wifi: regwifigrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_NAND_DATA03__GPIO3_IO09	0x110
+		>;
+	};
+
+	pinctrl_sai2: sai2grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SAI2_TXFS__AUDIOMIX_SAI2_TX_SYNC	0xd6
+			MX8MP_IOMUXC_SAI2_TXD0__AUDIOMIX_SAI2_TX_DATA00	0xd6
+			MX8MP_IOMUXC_SAI2_TXC__AUDIOMIX_SAI2_TX_BCLK	0xd6
+			MX8MP_IOMUXC_SAI2_MCLK__AUDIOMIX_SAI2_MCLK	0xd6
+		>;
+	};
+
+	pinctrl_spi2: spi2grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_ECSPI2_SCLK__ECSPI2_SCLK	0x82
+			MX8MP_IOMUXC_ECSPI2_MOSI__ECSPI2_MOSI	0x82
+			MX8MP_IOMUXC_ECSPI2_MISO__ECSPI2_MISO	0x82
+			MX8MP_IOMUXC_ECSPI2_SS0__GPIO5_IO13	0x140
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_UART1_RXD__UART1_DCE_RX	0x140
+			MX8MP_IOMUXC_UART1_TXD__UART1_DCE_TX	0x140
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_UART2_RXD__UART2_DCE_RX	0x140
+			MX8MP_IOMUXC_UART2_TXD__UART2_DCE_TX	0x140
+		>;
+	};
+
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_UART3_RXD__UART3_DCE_RX	0x140
+			MX8MP_IOMUXC_UART3_TXD__UART3_DCE_TX	0x140
+			MX8MP_IOMUXC_SAI5_RXD0__GPIO3_IO21	0x140
+			MX8MP_IOMUXC_SAI5_RXD1__GPIO3_IO22	0x140
+		>;
+	};
+
+	pinctrl_uart3_gpio: uart3gpiogrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_NAND_DATA02__GPIO3_IO08	0x110
+		>;
+	};
+
+	pinctrl_uart4: uart4grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_UART4_RXD__UART4_DCE_RX	0x140
+			MX8MP_IOMUXC_UART4_TXD__UART4_DCE_TX	0x140
+		>;
+	};
+
+	pinctrl_usb1: usb1grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_GPIO1_IO13__USB1_OTG_OC	0x140
+		>;
+	};
+
+	pinctrl_usbcon1: usb1congrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_GPIO1_IO10__GPIO1_IO10	0x140
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SD1_CLK__USDHC1_CLK	0x190
+			MX8MP_IOMUXC_SD1_CMD__USDHC1_CMD	0x1d0
+			MX8MP_IOMUXC_SD1_DATA0__USDHC1_DATA0	0x1d0
+			MX8MP_IOMUXC_SD1_DATA1__USDHC1_DATA1	0x1d0
+			MX8MP_IOMUXC_SD1_DATA2__USDHC1_DATA2	0x1d0
+			MX8MP_IOMUXC_SD1_DATA3__USDHC1_DATA3	0x1d0
+		>;
+	};
+
+	pinctrl_usdhc1_100mhz: usdhc1-100mhzgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SD1_CLK__USDHC1_CLK	0x194
+			MX8MP_IOMUXC_SD1_CMD__USDHC1_CMD	0x1d4
+			MX8MP_IOMUXC_SD1_DATA0__USDHC1_DATA0	0x1d4
+			MX8MP_IOMUXC_SD1_DATA1__USDHC1_DATA1	0x1d4
+			MX8MP_IOMUXC_SD1_DATA2__USDHC1_DATA2	0x1d4
+			MX8MP_IOMUXC_SD1_DATA3__USDHC1_DATA3	0x1d4
+		>;
+	};
+
+	pinctrl_usdhc1_200mhz: usdhc1-200mhzgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SD1_CLK__USDHC1_CLK	0x196
+			MX8MP_IOMUXC_SD1_CMD__USDHC1_CMD	0x1d6
+			MX8MP_IOMUXC_SD1_DATA0__USDHC1_DATA0	0x1d6
+			MX8MP_IOMUXC_SD1_DATA1__USDHC1_DATA1	0x1d6
+			MX8MP_IOMUXC_SD1_DATA2__USDHC1_DATA2	0x1d6
+			MX8MP_IOMUXC_SD1_DATA3__USDHC1_DATA3	0x1d6
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK	0x190
+			MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD	0x1d0
+			MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0	0x1d0
+			MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1	0x1d0
+			MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2	0x1d0
+			MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3	0x1d0
+			MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4	0x1d0
+			MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5	0x1d0
+			MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6	0x1d0
+			MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7	0x1d0
+			MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE	0x190
+		>;
+	};
+
+	pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK	0x194
+			MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD	0x1d4
+			MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0	0x1d4
+			MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1	0x1d4
+			MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2	0x1d4
+			MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3	0x1d4
+			MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4	0x1d4
+			MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5	0x1d4
+			MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6	0x1d4
+			MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7	0x1d4
+			MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE	0x194
+		>;
+	};
+
+	pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK	0x196
+			MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD	0x1d6
+			MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0	0x1d6
+			MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1	0x1d6
+			MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2	0x1d6
+			MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3	0x1d6
+			MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4	0x1d6
+			MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5	0x1d6
+			MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6	0x1d6
+			MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7	0x1d6
+			MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE	0x196
+		>;
+	};
+
+	pinctrl_wdog: wdoggrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_GPIO1_IO02__WDOG1_WDOG_B	0x166
+		>;
+	};
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mp-verdin-dahlia.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-verdin-dahlia.dtsi
new file mode 100644
index 000000000000..4b8f86f63081
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mp-verdin-dahlia.dtsi
@@ -0,0 +1,129 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/* TODO: Audio Codec */
+
+&backlight {
+	power-supply = <&reg_3p3v>;
+};
+
+/* Verdin SPI_1 */
+&ecspi1 {
+	status = "okay";
+};
+
+/* EEPROM on display adapter boards */
+&eeprom_display_adapter {
+	status = "okay";
+};
+
+/* EEPROM on Verdin Development board */
+&eeprom_carrier_board {
+	status = "okay";
+};
+
+&eqos {
+	status = "okay";
+};
+
+&flexcan1 {
+	status = "okay";
+};
+
+&flexcan2 {
+	status = "okay";
+};
+
+/* Verdin QSPI_1 */
+&flexspi {
+	status = "okay";
+};
+
+/* Current measurement into module VCC */
+&hwmon {
+	status = "okay";
+};
+
+&hwmon_temp {
+	vs-supply = <&reg_1p8v>;
+	status = "okay";
+};
+
+/* Verdin I2C_2_DSI */
+&i2c2 {
+	status = "okay";
+};
+
+&i2c3 {
+	status = "okay";
+};
+
+/* Verdin I2C_1 */
+&i2c4 {
+	status = "okay";
+
+	/* TODO: Audio Codec */
+};
+
+/* TODO: Verdin PCIE_1 */
+
+/* Verdin PWM_1 */
+&pwm1 {
+	status = "okay";
+};
+
+/* Verdin PWM_2 */
+&pwm2 {
+	status = "okay";
+};
+
+/* Verdin PWM_3_DSI */
+&pwm3 {
+	status = "okay";
+};
+
+&reg_usdhc2_vmmc {
+	vin-supply = <&reg_3p3v>;
+};
+
+/* TODO: Verdin I2S_1 */
+
+/* Verdin UART_1 */
+&uart1 {
+	status = "okay";
+};
+
+/* Verdin UART_2 */
+&uart2 {
+	status = "okay";
+};
+
+/* Verdin UART_3, used as the Linux Console */
+&uart3 {
+	status = "okay";
+};
+
+/* Verdin USB_1 */
+&usb3_0 {
+	status = "okay";
+};
+
+&usb3_phy0 {
+	status = "okay";
+};
+
+/* Verdin USB_2 */
+&usb3_1 {
+	status = "okay";
+};
+
+&usb3_phy1 {
+	status = "okay";
+};
+
+/* Verdin SD_1 */
+&usdhc2 {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mp-verdin-dev.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-verdin-dev.dtsi
new file mode 100644
index 000000000000..cefabe65b252
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mp-verdin-dev.dtsi
@@ -0,0 +1,46 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+#include "imx8mp-verdin-dahlia.dtsi"
+
+/ {
+	/* TODO: Audio Codec */
+
+	reg_eth2phy: regulator-eth2phy {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio_expander_21 4 GPIO_ACTIVE_HIGH>; /* ETH_PWR_EN */
+		off-on-delay = <500000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "+V3.3_ETH";
+		startup-delay-us = <200000>;
+		vin-supply = <&reg_3p3v>;
+	};
+};
+
+&fec {
+	phy-supply = <&reg_eth2phy>;
+	status = "okay";
+};
+
+&gpio_expander_21 {
+	status = "okay";
+	vcc-supply = <&reg_1p8v>;
+};
+
+/* TODO: Verdin I2C_1 with Audio Codec */
+
+/* Verdin UART_1, connector X50 through RS485 transceiver */
+&uart1 {
+	linux,rs485-enabled-at-boot-time;
+	rs485-rts-active-low;
+	rs485-rx-during-tx;
+};
+
+/* Limit frequency on dev board due to long traces and bad signal integrity */
+&usdhc2 {
+	max-frequency = <100000000>;
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mp-verdin-nonwifi-dahlia.dts b/arch/arm64/boot/dts/freescale/imx8mp-verdin-nonwifi-dahlia.dts
new file mode 100644
index 000000000000..68147b0c1b35
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mp-verdin-nonwifi-dahlia.dts
@@ -0,0 +1,18 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/dts-v1/;
+
+#include "imx8mp-verdin.dtsi"
+#include "imx8mp-verdin-nonwifi.dtsi"
+#include "imx8mp-verdin-dahlia.dtsi"
+
+/ {
+	model = "Toradex Verdin iMX8M Plus on Dahlia Board";
+	compatible = "toradex,verdin-imx8mp-nonwifi-dahlia",
+		     "toradex,verdin-imx8mp-nonwifi",
+		     "toradex,verdin-imx8mp",
+		     "fsl,imx8mp";
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mp-verdin-nonwifi-dev.dts b/arch/arm64/boot/dts/freescale/imx8mp-verdin-nonwifi-dev.dts
new file mode 100644
index 000000000000..879ff687cf2b
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mp-verdin-nonwifi-dev.dts
@@ -0,0 +1,18 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/dts-v1/;
+
+#include "imx8mp-verdin.dtsi"
+#include "imx8mp-verdin-nonwifi.dtsi"
+#include "imx8mp-verdin-dev.dtsi"
+
+/ {
+	model = "Toradex Verdin iMX8M Plus on Verdin Development Board";
+	compatible = "toradex,verdin-imx8mp-nonwifi-dev",
+		     "toradex,verdin-imx8mp-nonwifi",
+		     "toradex,verdin-imx8mp",
+		     "fsl,imx8mp";
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mp-verdin-nonwifi.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-verdin-nonwifi.dtsi
new file mode 100644
index 000000000000..91d597391b7c
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mp-verdin-nonwifi.dtsi
@@ -0,0 +1,54 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+&gpio5 {
+	gpio-line-names = "SODIMM_42",
+			  "SODIMM_46",
+			  "SODIMM_187",
+			  "SODIMM_20",
+			  "SODIMM_22",
+			  "SODIMM_15",
+			  "SODIMM_196",
+			  "SODIMM_200",
+			  "SODIMM_198",
+			  "SODIMM_202",
+			  "SODIMM_164",
+			  "SODIMM_152",
+			  "SODIMM_116",
+			  "SODIMM_128",
+			  "",
+			  "",
+			  "SODIMM_55",
+			  "SODIMM_53",
+			  "SODIMM_95",
+			  "SODIMM_93",
+			  "SODIMM_14",
+			  "SODIMM_12",
+			  "SODIMM_129",
+			  "SODIMM_131",
+			  "SODIMM_137",
+			  "SODIMM_139",
+			  "SODIMM_147",
+			  "SODIMM_149",
+			  "SODIMM_151",
+			  "SODIMM_153";
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpio1>, <&pinctrl_gpio2>,
+		    <&pinctrl_gpio3>, <&pinctrl_gpio4>,
+		    <&pinctrl_gpio7>, <&pinctrl_gpio8>,
+		    <&pinctrl_gpio_hog1>, <&pinctrl_gpio_hog2>, <&pinctrl_gpio_hog3>,
+		    <&pinctrl_hdmi_hog>;
+};
+
+/*
+ * Verdin UART_4
+ * Often used by the M7 and then should not be enabled here.
+ */
+&uart4 {
+	status = "disabled";
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mp-verdin-wifi-dahlia.dts b/arch/arm64/boot/dts/freescale/imx8mp-verdin-wifi-dahlia.dts
new file mode 100644
index 000000000000..804567f6ccee
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mp-verdin-wifi-dahlia.dts
@@ -0,0 +1,18 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/dts-v1/;
+
+#include "imx8mp-verdin.dtsi"
+#include "imx8mp-verdin-wifi.dtsi"
+#include "imx8mp-verdin-dahlia.dtsi"
+
+/ {
+	model = "Toradex Verdin iMX8M Plus WB on Dahlia Board";
+	compatible = "toradex,verdin-imx8mp-wifi-dahlia",
+		     "toradex,verdin-imx8mp-wifi",
+		     "toradex,verdin-imx8mp",
+		     "fsl,imx8mp";
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mp-verdin-wifi-dev.dts b/arch/arm64/boot/dts/freescale/imx8mp-verdin-wifi-dev.dts
new file mode 100644
index 000000000000..c1713c28cdce
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mp-verdin-wifi-dev.dts
@@ -0,0 +1,18 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/dts-v1/;
+
+#include "imx8mp-verdin.dtsi"
+#include "imx8mp-verdin-wifi.dtsi"
+#include "imx8mp-verdin-dev.dtsi"
+
+/ {
+	model = "Toradex Verdin iMX8M Plus WB on Verdin Development Board";
+	compatible = "toradex,verdin-imx8mp-wifi-dev",
+		     "toradex,verdin-imx8mp-wifi",
+		     "toradex,verdin-imx8mp",
+		     "fsl,imx8mp";
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mp-verdin-wifi.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-verdin-wifi.dtsi
new file mode 100644
index 000000000000..36289c175e6e
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mp-verdin-wifi.dtsi
@@ -0,0 +1,82 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+/ {
+	reg_wifi_en: regulator-wifi-en {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio2 11 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_wifi_pwr_en>;
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "PDn_AW-CM276NF";
+		startup-delay-us = <2000>;
+	};
+};
+
+&gpio5 {
+	gpio-line-names = "SODIMM_42",
+			  "SODIMM_46",
+			  "SODIMM_187",
+			  "SODIMM_20",
+			  "SODIMM_22",
+			  "SODIMM_15",
+			  "SODIMM_196",
+			  "SODIMM_200",
+			  "SODIMM_198",
+			  "SODIMM_202",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "SODIMM_55",
+			  "SODIMM_53",
+			  "SODIMM_95",
+			  "SODIMM_93",
+			  "SODIMM_14",
+			  "SODIMM_12",
+			  "SODIMM_129",
+			  "SODIMM_131",
+			  "SODIMM_137",
+			  "SODIMM_139",
+			  "SODIMM_147",
+			  "SODIMM_149",
+			  "SODIMM_151",
+			  "SODIMM_153";
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpio1>, <&pinctrl_gpio2>,
+		    <&pinctrl_gpio3>, <&pinctrl_gpio4>,
+		    <&pinctrl_gpio7>, <&pinctrl_gpio8>,
+		    <&pinctrl_gpio_hog2>, <&pinctrl_gpio_hog3>, <&pinctrl_gpio_hog4>,
+		    <&pinctrl_hdmi_hog>;
+};
+
+/* On-module Bluetooth */
+&uart4 {
+	uart-has-rtscts;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_bt_uart>;
+	status = "okay";
+};
+
+/* On-module Wi-Fi */
+&usdhc1 {
+	bus-width = <4>;
+	keep-power-in-suspend;
+	max-frequency = <100000000>;
+	non-removable;
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc1>, <&pinctrl_wifi_ctrl>;
+	pinctrl-1 = <&pinctrl_usdhc1_100mhz>, <&pinctrl_wifi_ctrl>;
+	pinctrl-2 = <&pinctrl_usdhc1_200mhz>, <&pinctrl_wifi_ctrl>;
+	vmmc-supply = <&reg_wifi_en>;
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mp-verdin.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-verdin.dtsi
new file mode 100644
index 000000000000..5dcd1de586b5
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mp-verdin.dtsi
@@ -0,0 +1,1403 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2022 Toradex
+ */
+
+#include "dt-bindings/pwm/pwm.h"
+#include "imx8mp.dtsi"
+
+/ {
+	chosen {
+		stdout-path = &uart3;
+	};
+
+	aliases {
+		/* Ethernet aliases to ensure correct MAC addresses */
+		ethernet0 = &eqos;
+		ethernet1 = &fec;
+		rtc0 = &rtc_i2c;
+		rtc1 = &snvs_rtc;
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		brightness-levels = <0 45 63 88 119 158 203 255>;
+		default-brightness-level = <4>;
+		/* Verdin I2S_2_D_OUT (DSI_1_BKL_EN/DSI_1_BKL_EN_LVDS, SODIMM 46) */
+		enable-gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_i2s_2_d_out_dsi_1_bkl_en>;
+		power-supply = <&reg_3p3v>;
+		/* Verdin PWM_3_DSI/PWM_3_DSI_LVDS (SODIMM 19) */
+		pwms = <&pwm3 0 6666667 PWM_POLARITY_INVERTED>;
+		status = "disabled";
+	};
+
+	backlight_mezzanine: backlight-mezzanine {
+		compatible = "pwm-backlight";
+		brightness-levels = <0 45 63 88 119 158 203 255>;
+		default-brightness-level = <4>;
+		/* Verdin GPIO 4 (SODIMM 212) */
+		enable-gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>;
+		/* Verdin PWM_2 (SODIMM 16) */
+		pwms = <&pwm2 0 6666667 PWM_POLARITY_INVERTED>;
+		status = "disabled";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_keys>;
+
+		button-wakeup {
+			debounce-interval = <10>;
+			/* Verdin CTRL_WAKE1_MICO# (SODIMM 252) */
+			gpios = <&gpio4 0 GPIO_ACTIVE_LOW>;
+			label = "Wake-Up";
+			linux,code = <KEY_WAKEUP>;
+			wakeup-source;
+		};
+	};
+
+	/* Carrier Board Supplies */
+	reg_1p8v: regulator-1p8v {
+		compatible = "regulator-fixed";
+		regulator-max-microvolt = <1800000>;
+		regulator-min-microvolt = <1800000>;
+		regulator-name = "+V1.8_SW";
+	};
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "+V3.3_SW";
+	};
+
+	reg_5p0v: regulator-5p0v {
+		compatible = "regulator-fixed";
+		regulator-max-microvolt = <5000000>;
+		regulator-min-microvolt = <5000000>;
+		regulator-name = "+V5_SW";
+	};
+
+	/* Non PMIC On-module Supplies */
+	reg_module_eth1phy: regulator-module-eth1phy {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio2 20 GPIO_ACTIVE_HIGH>; /* PMIC_EN_ETH */
+		off-on-delay = <500000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_eth>;
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "On-module +V3.3_ETH";
+		startup-delay-us = <200000>;
+		vin-supply = <&reg_vdd_3v3>;
+	};
+
+	reg_usb1_vbus: regulator-usb1-vbus {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		/* Verdin USB_1_EN (SODIMM 155) */
+		gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usb1_vbus>;
+		regulator-max-microvolt = <5000000>;
+		regulator-min-microvolt = <5000000>;
+		regulator-name = "USB_1_EN";
+	};
+
+	reg_usb2_vbus: regulator-usb2-vbus {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		/* Verdin USB_2_EN (SODIMM 185) */
+		gpio = <&gpio1 14 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usb2_vbus>;
+		regulator-max-microvolt = <5000000>;
+		regulator-min-microvolt = <5000000>;
+		regulator-name = "USB_2_EN";
+	};
+
+	reg_usdhc2_vmmc: regulator-usdhc2 {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		/* Verdin SD_1_PWR_EN (SODIMM 76) */
+		gpio = <&gpio4 22 GPIO_ACTIVE_HIGH>;
+		off-on-delay = <100000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usdhc2_pwr_en>;
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "+V3.3_SD";
+		startup-delay-us = <2000>;
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		/* Use the kernel configuration settings instead */
+		/delete-node/ linux,cma;
+	};
+};
+
+&A53_0 {
+	cpu-supply = <&reg_vdd_arm>;
+};
+
+&A53_1 {
+	cpu-supply = <&reg_vdd_arm>;
+};
+
+&A53_2 {
+	cpu-supply = <&reg_vdd_arm>;
+};
+
+&A53_3 {
+	cpu-supply = <&reg_vdd_arm>;
+};
+
+&cpu_alert0 {
+	temperature = <95000>;
+};
+
+&cpu_crit0 {
+	temperature = <105000>;
+};
+
+/* Verdin SPI_1 */
+&ecspi1 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	cs-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1>;
+};
+
+/* Verdin ETH_1 (On-module PHY) */
+&eqos {
+	phy-handle = <&ethphy0>;
+	phy-mode = "rgmii-id";
+	phy-supply = <&reg_module_eth1phy>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_eqos>;
+	snps,force_thresh_dma_mode;
+	snps,mtl-rx-config = <&mtl_rx_setup>;
+	snps,mtl-tx-config = <&mtl_tx_setup>;
+
+	mdio {
+		compatible = "snps,dwmac-mdio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy0: ethernet-phy@7 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			eee-broken-100tx;
+			eee-broken-1000t;
+			interrupt-parent = <&gpio1>;
+			interrupts = <10 IRQ_TYPE_LEVEL_LOW>;
+			micrel,led-mode = <0>;
+			reg = <7>;
+		};
+	};
+
+	mtl_rx_setup: rx-queues-config {
+		snps,rx-queues-to-use = <5>;
+		snps,rx-sched-sp;
+
+		queue0 {
+			snps,dcb-algorithm;
+			snps,priority = <0x1>;
+			snps,map-to-dma-channel = <0>;
+		};
+
+		queue1 {
+			snps,dcb-algorithm;
+			snps,priority = <0x2>;
+			snps,map-to-dma-channel = <1>;
+		};
+
+		queue2 {
+			snps,dcb-algorithm;
+			snps,priority = <0x4>;
+			snps,map-to-dma-channel = <2>;
+		};
+
+		queue3 {
+			snps,dcb-algorithm;
+			snps,priority = <0x8>;
+			snps,map-to-dma-channel = <3>;
+		};
+
+		queue4 {
+			snps,dcb-algorithm;
+			snps,priority = <0xf0>;
+			snps,map-to-dma-channel = <4>;
+		};
+	};
+
+	mtl_tx_setup: tx-queues-config {
+		snps,tx-queues-to-use = <5>;
+		snps,tx-sched-sp;
+
+		queue0 {
+			snps,dcb-algorithm;
+			snps,priority = <0x1>;
+		};
+
+		queue1 {
+			snps,dcb-algorithm;
+			snps,priority = <0x2>;
+		};
+
+		queue2 {
+			snps,dcb-algorithm;
+			snps,priority = <0x4>;
+		};
+
+		queue3 {
+			snps,dcb-algorithm;
+			snps,priority = <0x8>;
+		};
+
+		queue4 {
+			snps,dcb-algorithm;
+			snps,priority = <0xf0>;
+		};
+	};
+};
+
+/* Verdin ETH_2_RGMII */
+&fec {
+	fsl,magic-packet;
+	phy-handle = <&ethphy1>;
+	phy-mode = "rgmii-id";
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&pinctrl_fec>;
+	pinctrl-1 = <&pinctrl_fec_sleep>;
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy1: ethernet-phy@7 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			interrupt-parent = <&gpio4>;
+			interrupts = <18 IRQ_TYPE_LEVEL_LOW>;
+			micrel,led-mode = <0>;
+			reg = <7>;
+		};
+	};
+};
+
+/* Verdin CAN_1 */
+&flexcan1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan1>;
+	status = "disabled";
+};
+
+/* Verdin CAN_2 */
+&flexcan2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan2>;
+	status = "disabled";
+};
+
+/* Verdin QSPI_1 */
+&flexspi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexspi0>;
+};
+
+&gpio1 {
+	gpio-line-names = "SODIMM_206",
+			  "SODIMM_208",
+			  "",
+			  "",
+			  "",
+			  "SODIMM_210",
+			  "SODIMM_212",
+			  "SODIMM_216",
+			  "SODIMM_218",
+			  "",
+			  "",
+			  "SODIMM_16",
+			  "SODIMM_155",
+			  "SODIMM_157",
+			  "SODIMM_185",
+			  "SODIMM_91";
+};
+
+&gpio2 {
+	gpio-line-names = "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "SODIMM_143",
+			  "SODIMM_141",
+			  "",
+			  "",
+			  "SODIMM_161",
+			  "",
+			  "SODIMM_84",
+			  "SODIMM_78",
+			  "SODIMM_74",
+			  "SODIMM_80",
+			  "SODIMM_82",
+			  "SODIMM_70",
+			  "SODIMM_72";
+};
+
+&gpio3 {
+	gpio-line-names = "SODIMM_52",
+			  "SODIMM_54",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "SODIMM_56",
+			  "SODIMM_58",
+			  "SODIMM_60",
+			  "SODIMM_62",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "SODIMM_66",
+			  "",
+			  "SODIMM_64",
+			  "",
+			  "",
+			  "SODIMM_34",
+			  "SODIMM_19",
+			  "",
+			  "SODIMM_32",
+			  "",
+			  "",
+			  "SODIMM_30",
+			  "SODIMM_59",
+			  "SODIMM_57",
+			  "SODIMM_63",
+			  "SODIMM_61";
+};
+
+&gpio4 {
+	gpio-line-names = "SODIMM_252",
+			  "SODIMM_222",
+			  "SODIMM_36",
+			  "SODIMM_220",
+			  "SODIMM_193",
+			  "SODIMM_191",
+			  "SODIMM_201",
+			  "SODIMM_203",
+			  "SODIMM_205",
+			  "SODIMM_207",
+			  "SODIMM_199",
+			  "SODIMM_197",
+			  "SODIMM_221",
+			  "SODIMM_219",
+			  "SODIMM_217",
+			  "SODIMM_215",
+			  "SODIMM_211",
+			  "SODIMM_213",
+			  "SODIMM_189",
+			  "SODIMM_244",
+			  "SODIMM_38",
+			  "",
+			  "SODIMM_76",
+			  "SODIMM_135",
+			  "SODIMM_133",
+			  "SODIMM_17",
+			  "SODIMM_24",
+			  "SODIMM_26",
+			  "SODIMM_21",
+			  "SODIMM_256",
+			  "SODIMM_48",
+			  "SODIMM_44";
+
+	ctrl-sleep-moci-hog {
+		gpio-hog;
+		/* Verdin CTRL_SLEEP_MOCI# (SODIMM 256) */
+		gpios = <29 GPIO_ACTIVE_HIGH>;
+		line-name = "CTRL_SLEEP_MOCI#";
+		output-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ctrl_sleep_moci>;
+	};
+};
+
+/* On-module I2C */
+&i2c1 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	pinctrl-1 = <&pinctrl_i2c1_gpio>;
+	scl-gpios = <&gpio5 14 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio5 15 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "okay";
+
+	pca9450: pmic@25 {
+		compatible = "nxp,pca9450c";
+		interrupt-parent = <&gpio1>;
+		/* PMIC PCA9450 PMIC_nINT GPIO1_IO3 */
+		interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_pmic>;
+		reg = <0x25>;
+		sd-vsel-gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>;
+
+		/*
+		 * The bootloader is expected to switch on LDO4 for the on-module +V3.3_ADC and the
+		 * I2C level shifter for the TLA2024 ADC behind this PMIC.
+		 */
+
+		regulators {
+			BUCK1 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1000000>;
+				regulator-min-microvolt = <720000>;
+				regulator-name = "On-module +VDD_SOC (BUCK1)";
+				regulator-ramp-delay = <3125>;
+			};
+
+			reg_vdd_arm: BUCK2 {
+				nxp,dvs-run-voltage = <950000>;
+				nxp,dvs-standby-voltage = <850000>;
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1025000>;
+				regulator-min-microvolt = <720000>;
+				regulator-name = "On-module +VDD_ARM (BUCK2)";
+				regulator-ramp-delay = <3125>;
+			};
+
+			reg_vdd_3v3: BUCK4 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <3300000>;
+				regulator-min-microvolt = <3300000>;
+				regulator-name = "On-module +V3.3 (BUCK4)";
+			};
+
+			reg_vdd_1v8: BUCK5 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1800000>;
+				regulator-min-microvolt = <1800000>;
+				regulator-name = "PWR_1V8_MOCI (BUCK5)";
+			};
+
+			BUCK6 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1155000>;
+				regulator-min-microvolt = <1045000>;
+				regulator-name = "On-module +VDD_DDR (BUCK6)";
+			};
+
+			LDO1 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1950000>;
+				regulator-min-microvolt = <1650000>;
+				regulator-name = "On-module +V1.8_SNVS (LDO1)";
+			};
+
+			LDO2 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1150000>;
+				regulator-min-microvolt = <800000>;
+				regulator-name = "On-module +V0.8_SNVS (LDO2)";
+			};
+
+			LDO3 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <1800000>;
+				regulator-min-microvolt = <1800000>;
+				regulator-name = "On-module +V1.8A (LDO3)";
+			};
+
+			LDO4 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-max-microvolt = <3300000>;
+				regulator-min-microvolt = <3300000>;
+				regulator-name = "On-module +V3.3_ADC (LDO4)";
+			};
+
+			LDO5 {
+				regulator-max-microvolt = <3300000>;
+				regulator-min-microvolt = <1800000>;
+				regulator-name = "On-module +V3.3_1.8_SD (LDO5)";
+			};
+		};
+	};
+
+	rtc_i2c: rtc@32 {
+		compatible = "epson,rx8130";
+		reg = <0x32>;
+	};
+
+	/* On-module temperature sensor */
+	hwmon_temp_module: sensor@48 {
+		compatible = "ti,tmp1075";
+		reg = <0x48>;
+		vs-supply = <&reg_vdd_1v8>;
+	};
+
+	adc@49 {
+		compatible = "ti,ads1015";
+		reg = <0x49>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* Verdin I2C_1 (ADC_4 - ADC_3) */
+		channel@0 {
+			reg = <0>;
+			ti,datarate = <4>;
+			ti,gain = <2>;
+		};
+
+		/* Verdin I2C_1 (ADC_4 - ADC_1) */
+		channel@1 {
+			reg = <1>;
+			ti,datarate = <4>;
+			ti,gain = <2>;
+		};
+
+		/* Verdin I2C_1 (ADC_3 - ADC_1) */
+		channel@2 {
+			reg = <2>;
+			ti,datarate = <4>;
+			ti,gain = <2>;
+		};
+
+		/* Verdin I2C_1 (ADC_2 - ADC_1) */
+		channel@3 {
+			reg = <3>;
+			ti,datarate = <4>;
+			ti,gain = <2>;
+		};
+
+		/* Verdin I2C_1 ADC_4 */
+		channel@4 {
+			reg = <4>;
+			ti,datarate = <4>;
+			ti,gain = <2>;
+		};
+
+		/* Verdin I2C_1 ADC_3 */
+		channel@5 {
+			reg = <5>;
+			ti,datarate = <4>;
+			ti,gain = <2>;
+		};
+
+		/* Verdin I2C_1 ADC_2 */
+		channel@6 {
+			reg = <6>;
+			ti,datarate = <4>;
+			ti,gain = <2>;
+		};
+
+		/* Verdin I2C_1 ADC_1 */
+		channel@7 {
+			reg = <7>;
+			ti,datarate = <4>;
+			ti,gain = <2>;
+		};
+	};
+
+	eeprom@50 {
+		compatible = "st,24c02";
+		pagesize = <16>;
+		reg = <0x50>;
+	};
+};
+
+/* Verdin I2C_2_DSI */
+&i2c2 {
+	/* Lower frequency to avoid DDC/EDID issues with certain displays/screens. */
+	clock-frequency = <10000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	pinctrl-1 = <&pinctrl_i2c2_gpio>;
+	scl-gpios = <&gpio5 16 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio5 17 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+
+	atmel_mxt_ts_mezzanine: touch-mezzanine@4a {
+		compatible = "atmel,maxtouch";
+		/* Verdin GPIO_3 (SODIMM 210) */
+		interrupt-parent = <&gpio1>;
+		interrupts = <5 IRQ_TYPE_EDGE_FALLING>;
+		reg = <0x4a>;
+		/* Verdin GPIO_2 (SODIMM 208) */
+		reset-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
+		status = "disabled";
+	};
+};
+
+/* TODO: Verdin I2C_3_HDMI */
+
+/* Verdin I2C_4_CSI */
+&i2c3 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	pinctrl-1 = <&pinctrl_i2c3_gpio>;
+	scl-gpios = <&gpio5 18 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio5 19 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+};
+
+/* Verdin I2C_1 */
+&i2c4 {
+	clock-frequency = <400000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c4>;
+	pinctrl-1 = <&pinctrl_i2c4_gpio>;
+	scl-gpios = <&gpio5 20 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio5 21 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+
+	gpio_expander_21: gpio-expander@21 {
+		compatible = "nxp,pcal6416";
+		#gpio-cells = <2>;
+		gpio-controller;
+		reg = <0x21>;
+		vcc-supply = <&reg_3p3v>;
+		status = "disabled";
+	};
+
+	lvds_ti_sn65dsi83: bridge@2c {
+		compatible = "ti,sn65dsi83";
+		/* Verdin GPIO_9_DSI (SN65DSI84 IRQ, SODIMM 17, unused) */
+		/* Verdin GPIO_10_DSI (SODIMM 21) */
+		enable-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_10_dsi>;
+		reg = <0x2c>;
+		status = "disabled";
+	};
+
+	/* Current measurement into module VCC */
+	hwmon: hwmon@40 {
+		compatible = "ti,ina219";
+		reg = <0x40>;
+		shunt-resistor = <10000>;
+		status = "disabled";
+	};
+
+	hdmi_lontium_lt8912: hdmi@48 {
+		compatible = "lontium,lt8912b";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_10_dsi>, <&pinctrl_pwm_3_dsi_hpd_gpio>;
+		reg = <0x48>;
+		/* Verdin GPIO_9_DSI (LT8912 INT, SODIMM 17, unused) */
+		/* Verdin GPIO_10_DSI (SODIMM 21) */
+		reset-gpios = <&gpio4 28 GPIO_ACTIVE_LOW>;
+		status = "disabled";
+	};
+
+	atmel_mxt_ts: touch@4a {
+		compatible = "atmel,maxtouch";
+		/*
+		 * Verdin GPIO_9_DSI
+		 * (TOUCH_INT#, SODIMM 17, also routed to SN65DSI83 IRQ albeit currently unused)
+		 */
+		interrupt-parent = <&gpio4>;
+		interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_9_dsi>, <&pinctrl_i2s_2_bclk_touch_reset>;
+		reg = <0x4a>;
+		/* Verdin I2S_2_BCLK (TOUCH_RESET#, SODIMM 42) */
+		reset-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>;
+		status = "disabled";
+	};
+
+	/* Temperature sensor on carrier board */
+	hwmon_temp: sensor@4f {
+		compatible = "ti,tmp75c";
+		reg = <0x4f>;
+		status = "disabled";
+	};
+
+	/* EEPROM on display adapter (MIPI DSI Display Adapter) */
+	eeprom_display_adapter: eeprom@50 {
+		compatible = "st,24c02";
+		pagesize = <16>;
+		reg = <0x50>;
+		status = "disabled";
+	};
+
+	/* EEPROM on carrier board */
+	eeprom_carrier_board: eeprom@57 {
+		compatible = "st,24c02";
+		pagesize = <16>;
+		reg = <0x57>;
+		status = "disabled";
+	};
+};
+
+/* TODO: Verdin PCIE_1 */
+
+/* Verdin PWM_1 */
+&pwm1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm_1>;
+	#pwm-cells = <3>;
+};
+
+/* Verdin PWM_2 */
+&pwm2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm_2>;
+	#pwm-cells = <3>;
+};
+
+/* Verdin PWM_3_DSI */
+&pwm3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm_3>;
+	#pwm-cells = <3>;
+};
+
+/* TODO: Verdin I2S_1 */
+
+/* TODO: Verdin I2S_2 */
+
+&snvs_pwrkey {
+	status = "okay";
+};
+
+/* Verdin UART_1 */
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	uart-has-rtscts;
+};
+
+/* Verdin UART_2 */
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	uart-has-rtscts;
+};
+
+/* Verdin UART_3, used as the Linux Console */
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+};
+
+/* Verdin UART_4, used for Bluetooth on Wi-Fi/Bluetooth SKUs */
+&uart4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart4>;
+};
+
+/* Verdin USB_1 */
+&usb3_phy0 {
+	vbus-supply = <&reg_usb1_vbus>;
+};
+
+&usb_dwc3_0 {
+	adp-disable;
+	dr_mode = "otg";
+	hnp-disable;
+	maximum-speed = "high-speed";
+	over-current-active-low;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usb_1_id>;
+	srp-disable;
+};
+
+/* Verdin USB_2 */
+&usb3_phy1 {
+	vbus-supply = <&reg_usb2_vbus>;
+};
+
+&usb_dwc3_1 {
+	disable-over-current;
+	dr_mode = "host";
+};
+
+/* Verdin SD_1 */
+&usdhc2 {
+	assigned-clocks = <&clk IMX8MP_CLK_USDHC2>;
+	assigned-clock-rates = <400000000>;
+	bus-width = <4>;
+	cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
+	disable-wp;
+	pinctrl-names = "default", "state_100mhz", "state_200mhz", "sleep";
+	pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_cd>;
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_cd>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_cd>;
+	pinctrl-3 = <&pinctrl_usdhc2_sleep>, <&pinctrl_usdhc2_cd_sleep>;
+	vmmc-supply = <&reg_usdhc2_vmmc>;
+};
+
+/* On-module eMMC */
+&usdhc3 {
+	assigned-clocks = <&clk IMX8MP_CLK_USDHC3_ROOT>;
+	assigned-clock-rates = <400000000>;
+	bus-width = <8>;
+	non-removable;
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	pinctrl-1 = <&pinctrl_usdhc3_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc3_200mhz>;
+	status = "okay";
+};
+
+&wdog1 {
+	fsl,ext-reset-output;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog>;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_bt_uart: btuartgrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_ECSPI2_MISO__UART4_DCE_CTS	0x1c4>,
+			<MX8MP_IOMUXC_ECSPI2_MOSI__UART4_DCE_TX		0x1c4>,
+			<MX8MP_IOMUXC_ECSPI2_SCLK__UART4_DCE_RX		0x1c4>,
+			<MX8MP_IOMUXC_ECSPI2_SS0__UART4_DCE_RTS		0x1c4>;
+	};
+
+	pinctrl_ctrl_sleep_moci: ctrlsleepmocigrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_SAI3_RXC__GPIO4_IO29		0x1c4>;	/* SODIMM 256 */
+	};
+
+	pinctrl_ecspi1: ecspi1grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_ECSPI1_MISO__ECSPI1_MISO		0x1c4>,	/* SODIMM 198 */
+			<MX8MP_IOMUXC_ECSPI1_MOSI__ECSPI1_MOSI		0x4>,	/* SODIMM 200 */
+			<MX8MP_IOMUXC_ECSPI1_SCLK__ECSPI1_SCLK		0x4>,	/* SODIMM 196 */
+			<MX8MP_IOMUXC_ECSPI1_SS0__GPIO5_IO09		0x1c4>;	/* SODIMM 202 */
+	};
+
+	/* Connection On Board PHY */
+	pinctrl_eqos: eqosgrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_ENET_MDC__ENET_QOS_MDC				0x3>,
+			<MX8MP_IOMUXC_ENET_MDIO__ENET_QOS_MDIO				0x3>,
+			<MX8MP_IOMUXC_ENET_RD0__ENET_QOS_RGMII_RD0			0x91>,
+			<MX8MP_IOMUXC_ENET_RD1__ENET_QOS_RGMII_RD1			0x91>,
+			<MX8MP_IOMUXC_ENET_RD2__ENET_QOS_RGMII_RD2			0x91>,
+			<MX8MP_IOMUXC_ENET_RD3__ENET_QOS_RGMII_RD3			0x91>,
+			<MX8MP_IOMUXC_ENET_RXC__CCM_ENET_QOS_CLOCK_GENERATE_RX_CLK	0x91>,
+			<MX8MP_IOMUXC_ENET_RX_CTL__ENET_QOS_RGMII_RX_CTL		0x91>,
+			<MX8MP_IOMUXC_ENET_TD0__ENET_QOS_RGMII_TD0			0x1f>,
+			<MX8MP_IOMUXC_ENET_TD1__ENET_QOS_RGMII_TD1			0x1f>,
+			<MX8MP_IOMUXC_ENET_TD2__ENET_QOS_RGMII_TD2			0x1f>,
+			<MX8MP_IOMUXC_ENET_TD3__ENET_QOS_RGMII_TD3			0x1f>,
+			<MX8MP_IOMUXC_ENET_TX_CTL__ENET_QOS_RGMII_TX_CTL		0x1f>,
+			<MX8MP_IOMUXC_ENET_TXC__CCM_ENET_QOS_CLOCK_GENERATE_TX_CLK	0x1f>;
+	};
+
+	/* ETH_INT# shared with TPM_INT# (usually N/A) */
+	pinctrl_eth_tpm_int: ethtpmintgrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_GPIO1_IO10__GPIO1_IO10		0x1c4>;
+	};
+
+	/* Connection Carrier Board PHY ETH_2 */
+	pinctrl_fec: fecgrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_SAI1_RXD2__ENET1_MDC		0x3>,	/* SODIMM 193 */
+			<MX8MP_IOMUXC_SAI1_RXD3__ENET1_MDIO		0x3>,	/* SODIMM 191 */
+			<MX8MP_IOMUXC_SAI1_RXD4__ENET1_RGMII_RD0	0x91>,	/* SODIMM 201 */
+			<MX8MP_IOMUXC_SAI1_RXD5__ENET1_RGMII_RD1	0x91>,	/* SODIMM 203 */
+			<MX8MP_IOMUXC_SAI1_RXD6__ENET1_RGMII_RD2	0x91>,	/* SODIMM 205 */
+			<MX8MP_IOMUXC_SAI1_RXD7__ENET1_RGMII_RD3	0x91>,	/* SODIMM 207 */
+			<MX8MP_IOMUXC_SAI1_TXC__ENET1_RGMII_RXC		0x91>,	/* SODIMM 197 */
+			<MX8MP_IOMUXC_SAI1_TXFS__ENET1_RGMII_RX_CTL	0x91>,	/* SODIMM 199 */
+			<MX8MP_IOMUXC_SAI1_TXD0__ENET1_RGMII_TD0	0x1f>,	/* SODIMM 221 */
+			<MX8MP_IOMUXC_SAI1_TXD1__ENET1_RGMII_TD1	0x1f>,	/* SODIMM 219 */
+			<MX8MP_IOMUXC_SAI1_TXD2__ENET1_RGMII_TD2	0x1f>,	/* SODIMM 217 */
+			<MX8MP_IOMUXC_SAI1_TXD3__ENET1_RGMII_TD3	0x1f>,	/* SODIMM 215 */
+			<MX8MP_IOMUXC_SAI1_TXD4__ENET1_RGMII_TX_CTL	0x1f>,	/* SODIMM 211 */
+			<MX8MP_IOMUXC_SAI1_TXD5__ENET1_RGMII_TXC	0x1f>,	/* SODIMM 213 */
+			<MX8MP_IOMUXC_SAI1_TXD6__GPIO4_IO18		0x1c4>;	/* SODIMM 189 */
+	};
+
+	pinctrl_fec_sleep: fecsleepgrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_SAI1_RXD2__ENET1_MDC		0x3>,	/* SODIMM 193 */
+			<MX8MP_IOMUXC_SAI1_RXD3__ENET1_MDIO		0x3>,	/* SODIMM 191 */
+			<MX8MP_IOMUXC_SAI1_RXD4__ENET1_RGMII_RD0	0x91>,	/* SODIMM 201 */
+			<MX8MP_IOMUXC_SAI1_RXD5__ENET1_RGMII_RD1	0x91>,	/* SODIMM 203 */
+			<MX8MP_IOMUXC_SAI1_RXD6__ENET1_RGMII_RD2	0x91>,	/* SODIMM 205 */
+			<MX8MP_IOMUXC_SAI1_RXD7__ENET1_RGMII_RD3	0x91>,	/* SODIMM 207 */
+			<MX8MP_IOMUXC_SAI1_TXC__ENET1_RGMII_RXC		0x91>,	/* SODIMM 197 */
+			<MX8MP_IOMUXC_SAI1_TXFS__ENET1_RGMII_RX_CTL	0x91>,	/* SODIMM 199 */
+			<MX8MP_IOMUXC_SAI1_TXD0__GPIO4_IO12		0x1f>,	/* SODIMM 221 */
+			<MX8MP_IOMUXC_SAI1_TXD1__GPIO4_IO13		0x1f>,	/* SODIMM 219 */
+			<MX8MP_IOMUXC_SAI1_TXD2__GPIO4_IO14		0x1f>,	/* SODIMM 217 */
+			<MX8MP_IOMUXC_SAI1_TXD3__GPIO4_IO15		0x1f>,	/* SODIMM 215 */
+			<MX8MP_IOMUXC_SAI1_TXD4__GPIO4_IO16		0x1f>,	/* SODIMM 211 */
+			<MX8MP_IOMUXC_SAI1_TXD5__GPIO4_IO17		0x1f>,	/* SODIMM 213 */
+			<MX8MP_IOMUXC_SAI1_TXD6__GPIO4_IO18		0x184>;	/* SODIMM 189 */
+	};
+
+	pinctrl_flexcan1: flexcan1grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_SPDIF_RX__CAN1_RX			0x154>,	/* SODIMM 22 */
+			<MX8MP_IOMUXC_SPDIF_TX__CAN1_TX			0x154>;	/* SODIMM 20 */
+	};
+
+	pinctrl_flexcan2: flexcan2grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_SAI2_MCLK__CAN2_RX		0x154>,	/* SODIMM 26 */
+			<MX8MP_IOMUXC_SAI2_TXD0__CAN2_TX		0x154>;	/* SODIMM 24 */
+	};
+
+	pinctrl_flexspi0: flexspi0grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_NAND_ALE__FLEXSPI_A_SCLK		0x1c2>,	/* SODIMM 52 */
+			<MX8MP_IOMUXC_NAND_CE0_B__FLEXSPI_A_SS0_B	0x82>,	/* SODIMM 54 */
+			<MX8MP_IOMUXC_NAND_DQS__FLEXSPI_A_DQS		0x82>,	/* SODIMM 66 */
+			<MX8MP_IOMUXC_NAND_DATA00__FLEXSPI_A_DATA00	0x82>,	/* SODIMM 56 */
+			<MX8MP_IOMUXC_NAND_DATA01__FLEXSPI_A_DATA01	0x82>,	/* SODIMM 58 */
+			<MX8MP_IOMUXC_NAND_DATA02__FLEXSPI_A_DATA02	0x82>,	/* SODIMM 60 */
+			<MX8MP_IOMUXC_NAND_DATA03__FLEXSPI_A_DATA03	0x82>,	/* SODIMM 62 */
+			<MX8MP_IOMUXC_NAND_READY_B__GPIO3_IO16		0x82>;	/* SODIMM 64 */
+	};
+
+	pinctrl_gpio1: gpio1grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_GPIO1_IO00__GPIO1_IO00		0x184>;	/* SODIMM 206 */
+	};
+
+	pinctrl_gpio2: gpio2grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_GPIO1_IO01__GPIO1_IO01		0x1c4>;	/* SODIMM 208 */
+	};
+
+	pinctrl_gpio3: gpio3grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_GPIO1_IO05__GPIO1_IO05		0x184>;	/* SODIMM 210 */
+	};
+
+	pinctrl_gpio4: gpio4grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_GPIO1_IO06__GPIO1_IO06		0x184>;	/* SODIMM 212 */
+	};
+
+	pinctrl_gpio5: gpio5grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_GPIO1_IO07__GPIO1_IO07		0x184>;	/* SODIMM 216 */
+	};
+
+	pinctrl_gpio6: gpio6grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_GPIO1_IO08__GPIO1_IO08		0x184>;	/* SODIMM 218 */
+	};
+
+	pinctrl_gpio7: gpio7grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_SAI1_RXD1__GPIO4_IO03		0x184>;	/* SODIMM 220 */
+	};
+
+	pinctrl_gpio8: gpio8grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_SAI1_RXC__GPIO4_IO01		0x184>;	/* SODIMM 222 */
+	};
+
+	/* Verdin GPIO_9_DSI (pulled-up as active-low) */
+	pinctrl_gpio_9_dsi: gpio9dsigrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_SAI2_TXC__GPIO4_IO25		0x1c4>;	/* SODIMM 17 */
+	};
+
+	/* Verdin GPIO_10_DSI */
+	pinctrl_gpio_10_dsi: gpio10dsigrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_SAI3_RXFS__GPIO4_IO28		0x1c4>;	/* SODIMM 21 */
+	};
+
+	/* Non-wifi MSP usage only */
+	pinctrl_gpio_hog1: gpiohog1grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_ECSPI2_MISO__GPIO5_IO12		0x1c4>,	/* SODIMM 116 */
+			<MX8MP_IOMUXC_ECSPI2_MOSI__GPIO5_IO11		0x1c4>,	/* SODIMM 152 */
+			<MX8MP_IOMUXC_ECSPI2_SCLK__GPIO5_IO10		0x1c4>,	/* SODIMM 164 */
+			<MX8MP_IOMUXC_ECSPI2_SS0__GPIO5_IO13		0x1c4>;	/* SODIMM 128 */
+	};
+
+	/* USB_2_OC# */
+	pinctrl_gpio_hog2: gpiohog2grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_SAI3_MCLK__GPIO5_IO02		0x1c4>;	/* SODIMM 187 */
+	};
+
+	pinctrl_gpio_hog3: gpiohog3grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_GPIO1_IO13__GPIO1_IO13		0x1c4>,	/* SODIMM 157 */
+			/* CSI_1_MCLK */
+			<MX8MP_IOMUXC_GPIO1_IO15__GPIO1_IO15		0x1c4>;	/* SODIMM 91 */
+	};
+
+	/* Wifi usage only */
+	pinctrl_gpio_hog4: gpiohog4grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_UART4_RXD__GPIO5_IO28		0x1c4>,	/* SODIMM 151 */
+			<MX8MP_IOMUXC_UART4_TXD__GPIO5_IO29		0x1c4>;	/* SODIMM 153 */
+	};
+
+	pinctrl_gpio_keys: gpiokeysgrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_SAI1_RXFS__GPIO4_IO00		0x1c4>;	/* SODIMM 252 */
+	};
+
+	pinctrl_hdmi_hog: hdmihoggrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_HDMI_CEC__HDMIMIX_HDMI_CEC	0x40000019>,	/* SODIMM 63 */
+			<MX8MP_IOMUXC_HDMI_DDC_SCL__HDMIMIX_HDMI_SCL	0x400001c3>,	/* SODIMM 59 */
+			<MX8MP_IOMUXC_HDMI_DDC_SDA__HDMIMIX_HDMI_SDA	0x400001c3>,	/* SODIMM 57 */
+			<MX8MP_IOMUXC_HDMI_HPD__HDMIMIX_HDMI_HPD	0x40000019>;	/* SODIMM 61 */
+	};
+
+	/* On-module I2C */
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_I2C1_SCL__I2C1_SCL		0x400001c6>,	/* PMIC_I2C_SCL */
+			<MX8MP_IOMUXC_I2C1_SDA__I2C1_SDA		0x400001c6>;	/* PMIC_I2C_SDA */
+	};
+
+	pinctrl_i2c1_gpio: i2c1gpiogrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_I2C1_SCL__GPIO5_IO14		0x400001c6>,	/* PMIC_I2C_SCL */
+			<MX8MP_IOMUXC_I2C1_SDA__GPIO5_IO15		0x400001c6>;	/* PMIC_I2C_SDA */
+	};
+
+	/* Verdin I2C_2_DSI */
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_I2C2_SCL__I2C2_SCL		0x400001c6>,	/* SODIMM 55 */
+			<MX8MP_IOMUXC_I2C2_SDA__I2C2_SDA		0x400001c6>;	/* SODIMM 53 */
+	};
+
+	pinctrl_i2c2_gpio: i2c2gpiogrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_I2C2_SCL__GPIO5_IO16		0x400001c6>,	/* SODIMM 55 */
+			<MX8MP_IOMUXC_I2C2_SDA__GPIO5_IO17		0x400001c6>;	/* SODIMM 53 */
+	};
+
+	/* Verdin I2C_4_CSI */
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_I2C3_SCL__I2C3_SCL		0x400001c6>,	/* SODIMM 95 */
+			<MX8MP_IOMUXC_I2C3_SDA__I2C3_SDA		0x400001c6>;	/* SODIMM 93 */
+	};
+
+	pinctrl_i2c3_gpio: i2c3gpiogrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_I2C3_SCL__GPIO5_IO18		0x400001c6>,	/* SODIMM 95 */
+			<MX8MP_IOMUXC_I2C3_SDA__GPIO5_IO19		0x400001c6>;	/* SODIMM 93 */
+	};
+
+	/* Verdin I2C_1 */
+	pinctrl_i2c4: i2c4grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_I2C4_SCL__I2C4_SCL		0x400001c6>,	/* SODIMM 14 */
+			<MX8MP_IOMUXC_I2C4_SDA__I2C4_SDA		0x400001c6>;	/* SODIMM 12 */
+	};
+
+	pinctrl_i2c4_gpio: i2c4gpiogrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_I2C4_SCL__GPIO5_IO20		0x400001c6>,	/* SODIMM 14 */
+			<MX8MP_IOMUXC_I2C4_SDA__GPIO5_IO21		0x400001c6>;	/* SODIMM 12 */
+	};
+
+	/* Verdin I2S_2_BCLK (TOUCH_RESET#) */
+	pinctrl_i2s_2_bclk_touch_reset: i2s2bclktouchresetgrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_SAI3_TXC__GPIO5_IO00		0x184>;	/* SODIMM 42 */
+	};
+
+	/* Verdin I2S_2_D_OUT shared with SAI3 */
+	pinctrl_i2s_2_d_out_dsi_1_bkl_en: i2s2doutdsi1bklengrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_SAI3_TXD__GPIO5_IO01		0x184>;	/* SODIMM 46 */
+	};
+
+	pinctrl_pcie: pciegrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_SAI1_TXD7__GPIO4_IO19		0x4>,	/* SODIMM 244 */
+			<MX8MP_IOMUXC_SD2_RESET_B__GPIO2_IO19		0x1c4>;	/* PMIC_EN_PCIe_CLK, unused */
+	};
+
+	pinctrl_pmic: pmicirqgrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_GPIO1_IO03__GPIO1_IO03		0x1c4>;	/* PMIC_INT# */
+	};
+
+	pinctrl_pwm_1: pwm1grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_SPDIF_EXT_CLK__PWM1_OUT		0x6>;	/* SODIMM 15 */
+	};
+
+	pinctrl_pwm_2: pwm2grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_GPIO1_IO11__PWM2_OUT		0x6>;	/* SODIMM 16 */
+	};
+
+	/* Verdin PWM_3_DSI shared with GPIO3_IO20 */
+	pinctrl_pwm_3: pwm3grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_SAI5_RXC__PWM3_OUT		0x6>;	/* SODIMM 19 */
+	};
+
+	/* Verdin PWM_3_DSI (pulled-down as active-high) shared with PWM3_OUT */
+	pinctrl_pwm_3_dsi_hpd_gpio: pwm3dsi1hpdgpiogrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_SAI5_RXC__GPIO3_IO20		0x184>;	/* SODIMM 19 */
+	};
+
+	pinctrl_reg_eth: regethgrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_SD2_WP__GPIO2_IO20		0x184>;	/* PMIC_EN_ETH */
+	};
+
+	pinctrl_sai1: sai1grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_SAI1_MCLK__AUDIOMIX_SAI1_MCLK		0x96>,	/* SODIMM 38 */
+			<MX8MP_IOMUXC_SAI1_RXD0__AUDIOMIX_SAI1_RX_DATA00	0x1d6>,	/* SODIMM 36 */
+			<MX8MP_IOMUXC_SAI5_MCLK__AUDIOMIX_SAI1_TX_BCLK		0x1d6>,	/* SODIMM 30 */
+			<MX8MP_IOMUXC_SAI5_RXD1__AUDIOMIX_SAI1_TX_SYNC		0x1d6>,	/* SODIMM 32 */
+			<MX8MP_IOMUXC_SAI5_RXFS__AUDIOMIX_SAI1_TX_DATA00	0x96>;	/* SODIMM 34 */
+	};
+
+	pinctrl_sai3: sai3grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_SAI3_RXD__AUDIOMIX_SAI3_RX_DATA00	0x1d6>,	/* SODIMM 48 */
+			<MX8MP_IOMUXC_SAI3_TXC__AUDIOMIX_SAI3_TX_BCLK	0x1d6>,	/* SODIMM 42 */
+			<MX8MP_IOMUXC_SAI3_TXD__AUDIOMIX_SAI3_TX_DATA00	0x96>,	/* SODIMM 46 */
+			<MX8MP_IOMUXC_SAI3_TXFS__AUDIOMIX_SAI3_TX_SYNC	0x1d6>;	/* SODIMM 44 */
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_SAI2_RXD0__UART1_DCE_RTS		0x1c4>,	/* SODIMM 135 */
+			<MX8MP_IOMUXC_SAI2_TXFS__UART1_DCE_CTS		0x1c4>,	/* SODIMM 133 */
+			<MX8MP_IOMUXC_UART1_RXD__UART1_DCE_RX		0x1c4>,	/* SODIMM 129 */
+			<MX8MP_IOMUXC_UART1_TXD__UART1_DCE_TX		0x1c4>;	/* SODIMM 131 */
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_SD1_DATA4__UART2_DCE_RTS		0x1c4>,	/* SODIMM 143 */
+			<MX8MP_IOMUXC_SD1_DATA5__UART2_DCE_CTS		0x1c4>,	/* SODIMM 141 */
+			<MX8MP_IOMUXC_UART2_RXD__UART2_DCE_RX		0x1c4>,	/* SODIMM 137 */
+			<MX8MP_IOMUXC_UART2_TXD__UART2_DCE_TX		0x1c4>; /* SODIMM 139 */
+	};
+
+	pinctrl_uart3: uart3grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_UART3_RXD__UART3_DCE_RX		0x1c4>,	/* SODIMM 147 */
+			<MX8MP_IOMUXC_UART3_TXD__UART3_DCE_TX		0x1c4>;	/* SODIMM 149 */
+	};
+
+	/* Non-wifi usage only */
+	pinctrl_uart4: uart4grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_UART4_RXD__UART4_DCE_RX		0x1c4>,	/* SODIMM 151 */
+			<MX8MP_IOMUXC_UART4_TXD__UART4_DCE_TX		0x1c4>;	/* SODIMM 153 */
+	};
+
+	pinctrl_usb1_vbus: usb1vbusgrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_GPIO1_IO12__USB1_OTG_PWR		0x19>;	/* SODIMM 155 */
+	};
+
+	/* USB_1_ID */
+	pinctrl_usb_1_id: usb1idgrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_SD1_RESET_B__GPIO2_IO10		0x1c4>;	/* SODIMM 161 */
+	};
+
+	pinctrl_usb2_vbus: usb2vbusgrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_GPIO1_IO14__USB2_OTG_PWR		0x19>;	/* SODIMM 185 */
+	};
+
+	/* On-module Wi-Fi */
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_SD1_CLK__USDHC1_CLK		0x190>,
+			<MX8MP_IOMUXC_SD1_CMD__USDHC1_CMD		0x1d0>,
+			<MX8MP_IOMUXC_SD1_DATA0__USDHC1_DATA0		0x1d0>,
+			<MX8MP_IOMUXC_SD1_DATA1__USDHC1_DATA1		0x1d0>,
+			<MX8MP_IOMUXC_SD1_DATA2__USDHC1_DATA2		0x1d0>,
+			<MX8MP_IOMUXC_SD1_DATA3__USDHC1_DATA3		0x1d0>;
+	};
+
+	pinctrl_usdhc1_100mhz: usdhc1-100mhzgrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_SD1_CLK__USDHC1_CLK		0x194>,
+			<MX8MP_IOMUXC_SD1_CMD__USDHC1_CMD		0x1d4>,
+			<MX8MP_IOMUXC_SD1_DATA0__USDHC1_DATA0		0x1d4>,
+			<MX8MP_IOMUXC_SD1_DATA1__USDHC1_DATA1		0x1d4>,
+			<MX8MP_IOMUXC_SD1_DATA2__USDHC1_DATA2		0x1d4>,
+			<MX8MP_IOMUXC_SD1_DATA3__USDHC1_DATA3		0x1d4>;
+	};
+
+	pinctrl_usdhc1_200mhz: usdhc1-200mhzgrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_SD1_CLK__USDHC1_CLK		0x196>,
+			<MX8MP_IOMUXC_SD1_CMD__USDHC1_CMD		0x1d6>,
+			<MX8MP_IOMUXC_SD1_DATA0__USDHC1_DATA0		0x1d6>,
+			<MX8MP_IOMUXC_SD1_DATA1__USDHC1_DATA1		0x1d6>,
+			<MX8MP_IOMUXC_SD1_DATA2__USDHC1_DATA2		0x1d6>,
+			<MX8MP_IOMUXC_SD1_DATA3__USDHC1_DATA3		0x1d6>;
+	};
+
+	pinctrl_usdhc2_cd: usdhc2cdgrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_SD2_CD_B__GPIO2_IO12		0x1c4>;	/* SODIMM 84 */
+	};
+
+	pinctrl_usdhc2_cd_sleep: usdhc2cdslpgrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_SD2_CD_B__GPIO2_IO12		0x0>;	/* SODIMM 84 */
+	};
+
+	pinctrl_usdhc2_pwr_en: usdhc2pwrengrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_SAI2_RXC__GPIO4_IO22		0x4>;	/* SODIMM 76 */
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT	0x4>,	/* PMIC_USDHC_VSELECT */
+			<MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK		0x190>,	/* SODIMM 78 */
+			<MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD		0x1d0>,	/* SODIMM 74 */
+			<MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0		0x1d0>,	/* SODIMM 80 */
+			<MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1		0x1d0>,	/* SODIMM 82 */
+			<MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2		0x1d0>,	/* SODIMM 70 */
+			<MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3		0x1d0>;	/* SODIMM 72 */
+	};
+
+	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT	0x4>,
+			<MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK		0x194>,
+			<MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD		0x1d4>,
+			<MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0		0x1d4>,
+			<MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1		0x1d4>,
+			<MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2		0x1d4>,
+			<MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3		0x1d4>;
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT	0x4>,
+			<MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK		0x196>,
+			<MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD		0x1d6>,
+			<MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0		0x1d6>,
+			<MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1		0x1d6>,
+			<MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2		0x1d6>,
+			<MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3		0x1d6>;
+	};
+
+	/* Avoid backfeeding with removed card power */
+	pinctrl_usdhc2_sleep: usdhc2slpgrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_GPIO1_IO04__USDHC2_VSELECT	0x0>,
+			<MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK		0x100>,
+			<MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD		0x100>,
+			<MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0		0x100>,
+			<MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1		0x100>,
+			<MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2		0x100>,
+			<MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3		0x100>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins =
+			<MX8MP_IOMUXC_GPIO1_IO09__USDHC3_RESET_B	0x1d1>,
+			<MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE		0x190>,
+			<MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5		0x1d0>,
+			<MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6		0x1d0>,
+			<MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7		0x1d0>,
+			<MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0		0x1d0>,
+			<MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1		0x1d0>,
+			<MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2		0x1d0>,
+			<MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3		0x1d0>,
+			<MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4		0x1d0>,
+			<MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK		0x190>,
+			<MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD		0x1d0>;
+	};
+
+	pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_GPIO1_IO09__USDHC3_RESET_B	0x1d1>,
+			<MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE		0x194>,
+			<MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5		0x1d4>,
+			<MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6		0x1d4>,
+			<MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7		0x1d4>,
+			<MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0		0x1d4>,
+			<MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1		0x1d4>,
+			<MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2		0x1d4>,
+			<MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3		0x1d4>,
+			<MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4		0x1d4>,
+			<MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK		0x194>,
+			<MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD		0x1d4>;
+	};
+
+	pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_GPIO1_IO09__USDHC3_RESET_B	0x1d1>,
+			<MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE		0x196>,
+			<MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5		0x1d2>,
+			<MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6		0x1d2>,
+			<MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7		0x1d2>,
+			<MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0		0x1d2>,
+			<MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1		0x1d2>,
+			<MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2		0x1d2>,
+			<MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3		0x1d2>,
+			<MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4		0x1d2>,
+			<MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK		0x196>,
+			<MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD		0x1d6>;
+	};
+
+	pinctrl_wdog: wdoggrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_GPIO1_IO02__WDOG1_WDOG_B		0xc6>;	/* PMIC_WDI */
+	};
+
+	pinctrl_bluetooth_ctrl: bluetoothctrlgrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_SD1_DATA6__GPIO2_IO08		0x1c4>;	/* WIFI_WKUP_BT */
+	};
+
+	pinctrl_wifi_ctrl: wifictrlgrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_SD1_DATA7__GPIO2_IO09		0x1c4>;	/* WIFI_WKUP_WLAN */
+	};
+
+	pinctrl_wifi_i2s: wifii2sgrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_SAI2_RXFS__GPIO4_IO21		0x1d6>,	/* WIFI_TX_SYNC */
+			<MX8MP_IOMUXC_SAI5_RXD0__GPIO3_IO21		0x96>,	/* WIFI_RX_DATA0 */
+			<MX8MP_IOMUXC_SAI5_RXD2__GPIO3_IO23		0x1d6>,	/* WIFI_TX_BCLK */
+			<MX8MP_IOMUXC_SAI5_RXD3__GPIO3_IO24		0x1d6>;	/* WIFI_TX_DATA0 */
+	};
+
+	pinctrl_wifi_pwr_en: wifipwrengrp {
+		fsl,pins =
+			<MX8MP_IOMUXC_SD1_STROBE__GPIO2_IO11		0x184>;	/* PMIC_EN_WIFI */
+	};
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mp.dtsi b/arch/arm64/boot/dts/freescale/imx8mp.dtsi
index 04d259de5667..bb916a0948a8 100644
--- a/arch/arm64/boot/dts/freescale/imx8mp.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mp.dtsi
@@ -4,8 +4,11 @@
  */
 
 #include <dt-bindings/clock/imx8mp-clock.h>
+#include <dt-bindings/power/imx8mp-power.h>
+#include <dt-bindings/reset/imx8mp-reset.h>
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>
+#include <dt-bindings/interconnect/fsl,imx8mp.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/thermal/thermal.h>
 
@@ -51,7 +54,16 @@
 			clock-latency = <61036>;
 			clocks = <&clk IMX8MP_CLK_ARM>;
 			enable-method = "psci";
+			i-cache-size = <0x8000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <128>;
 			next-level-cache = <&A53_L2>;
+			nvmem-cells = <&cpu_speed_grade>;
+			nvmem-cell-names = "speed_grade";
+			operating-points-v2 = <&a53_opp_table>;
 			#cooling-cells = <2>;
 		};
 
@@ -62,7 +74,14 @@
 			clock-latency = <61036>;
 			clocks = <&clk IMX8MP_CLK_ARM>;
 			enable-method = "psci";
+			i-cache-size = <0x8000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <128>;
 			next-level-cache = <&A53_L2>;
+			operating-points-v2 = <&a53_opp_table>;
 			#cooling-cells = <2>;
 		};
 
@@ -73,7 +92,14 @@
 			clock-latency = <61036>;
 			clocks = <&clk IMX8MP_CLK_ARM>;
 			enable-method = "psci";
+			i-cache-size = <0x8000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <128>;
 			next-level-cache = <&A53_L2>;
+			operating-points-v2 = <&a53_opp_table>;
 			#cooling-cells = <2>;
 		};
 
@@ -84,12 +110,52 @@
 			clock-latency = <61036>;
 			clocks = <&clk IMX8MP_CLK_ARM>;
 			enable-method = "psci";
+			i-cache-size = <0x8000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <128>;
 			next-level-cache = <&A53_L2>;
+			operating-points-v2 = <&a53_opp_table>;
 			#cooling-cells = <2>;
 		};
 
 		A53_L2: l2-cache0 {
 			compatible = "cache";
+			cache-level = <2>;
+			cache-size = <0x80000>;
+			cache-line-size = <64>;
+			cache-sets = <512>;
+		};
+	};
+
+	a53_opp_table: opp-table {
+		compatible = "operating-points-v2";
+		opp-shared;
+
+		opp-1200000000 {
+			opp-hz = /bits/ 64 <1200000000>;
+			opp-microvolt = <850000>;
+			opp-supported-hw = <0x8a0>, <0x7>;
+			clock-latency-ns = <150000>;
+			opp-suspend;
+		};
+
+		opp-1600000000 {
+			opp-hz = /bits/ 64 <1600000000>;
+			opp-microvolt = <950000>;
+			opp-supported-hw = <0xa0>, <0x7>;
+			clock-latency-ns = <150000>;
+			opp-suspend;
+		};
+
+		opp-1800000000 {
+			opp-hz = /bits/ 64 <1800000000>;
+			opp-microvolt = <1000000>;
+			opp-supported-hw = <0x20>, <0x3>;
+			clock-latency-ns = <150000>;
+			opp-suspend;
 		};
 	};
 
@@ -131,7 +197,7 @@
 	clk_ext4: clock-ext4 {
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
-		clock-frequency= <133000000>;
+		clock-frequency = <133000000>;
 		clock-output-names = "clk_ext4";
 	};
 
@@ -229,7 +295,7 @@
 		arm,no-tick-in-suspend;
 	};
 
-	soc@0 {
+	soc: soc@0 {
 		compatible = "fsl,imx8mp-soc", "simple-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -369,6 +435,10 @@
 				eth_mac1: mac-address@90 {
 					reg = <0x90 6>;
 				};
+
+				eth_mac2: mac-address@96 {
+					reg = <0x96 6>;
+				};
 			};
 
 			anatop: anatop@30360000 {
@@ -401,6 +471,11 @@
 					wakeup-source;
 					status = "disabled";
 				};
+
+				snvs_lpgpr: snvs-lpgpr {
+					compatible = "fsl,imx8mp-snvs-lpgpr",
+						     "fsl,imx7d-snvs-lpgpr";
+				};
 			};
 
 			clk: clock-controller@30380000 {
@@ -443,6 +518,121 @@
 				interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
 				#reset-cells = <1>;
 			};
+
+			gpc: gpc@303a0000 {
+				compatible = "fsl,imx8mp-gpc";
+				reg = <0x303a0000 0x1000>;
+				interrupt-parent = <&gic>;
+				interrupt-controller;
+				#interrupt-cells = <3>;
+
+				pgc {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					pgc_mipi_phy1: power-domain@0 {
+						#power-domain-cells = <0>;
+						reg = <IMX8MP_POWER_DOMAIN_MIPI_PHY1>;
+					};
+
+					pgc_pcie_phy: power-domain@1 {
+						#power-domain-cells = <0>;
+						reg = <IMX8MP_POWER_DOMAIN_PCIE_PHY>;
+					};
+
+					pgc_usb1_phy: power-domain@2 {
+						#power-domain-cells = <0>;
+						reg = <IMX8MP_POWER_DOMAIN_USB1_PHY>;
+					};
+
+					pgc_usb2_phy: power-domain@3 {
+						#power-domain-cells = <0>;
+						reg = <IMX8MP_POWER_DOMAIN_USB2_PHY>;
+					};
+
+					pgc_gpu2d: power-domain@6 {
+						#power-domain-cells = <0>;
+						reg = <IMX8MP_POWER_DOMAIN_GPU2D>;
+						clocks = <&clk IMX8MP_CLK_GPU2D_ROOT>;
+						power-domains = <&pgc_gpumix>;
+					};
+
+					pgc_gpumix: power-domain@7 {
+						#power-domain-cells = <0>;
+						reg = <IMX8MP_POWER_DOMAIN_GPUMIX>;
+						clocks = <&clk IMX8MP_CLK_GPU_ROOT>,
+							 <&clk IMX8MP_CLK_GPU_AHB>;
+						assigned-clocks = <&clk IMX8MP_CLK_GPU_AXI>,
+								  <&clk IMX8MP_CLK_GPU_AHB>;
+						assigned-clock-parents = <&clk IMX8MP_SYS_PLL1_800M>,
+									 <&clk IMX8MP_SYS_PLL1_800M>;
+						assigned-clock-rates = <800000000>, <400000000>;
+					};
+
+					pgc_gpu3d: power-domain@9 {
+						#power-domain-cells = <0>;
+						reg = <IMX8MP_POWER_DOMAIN_GPU3D>;
+						clocks = <&clk IMX8MP_CLK_GPU3D_ROOT>,
+							 <&clk IMX8MP_CLK_GPU3D_SHADER_CORE>;
+						power-domains = <&pgc_gpumix>;
+					};
+
+					pgc_mediamix: power-domain@10 {
+						#power-domain-cells = <0>;
+						reg = <IMX8MP_POWER_DOMAIN_MEDIAMIX>;
+						clocks = <&clk IMX8MP_CLK_MEDIA_AXI_ROOT>,
+							 <&clk IMX8MP_CLK_MEDIA_APB_ROOT>;
+					};
+
+					pgc_mipi_phy2: power-domain@16 {
+						#power-domain-cells = <0>;
+						reg = <IMX8MP_POWER_DOMAIN_MIPI_PHY2>;
+					};
+
+					pgc_hsiomix: power-domains@17 {
+						#power-domain-cells = <0>;
+						reg = <IMX8MP_POWER_DOMAIN_HSIOMIX>;
+						clocks = <&clk IMX8MP_CLK_HSIO_AXI>,
+							 <&clk IMX8MP_CLK_HSIO_ROOT>;
+						assigned-clocks = <&clk IMX8MP_CLK_HSIO_AXI>;
+						assigned-clock-parents = <&clk IMX8MP_SYS_PLL2_500M>;
+						assigned-clock-rates = <500000000>;
+					};
+
+					pgc_ispdwp: power-domain@18 {
+						#power-domain-cells = <0>;
+						reg = <IMX8MP_POWER_DOMAIN_MEDIAMIX_ISPDWP>;
+						clocks = <&clk IMX8MP_CLK_MEDIA_ISP_ROOT>;
+					};
+
+					pgc_vpumix: power-domain@19 {
+						#power-domain-cells = <0>;
+						reg = <IMX8MP_POWER_DOMAIN_VPUMIX>;
+						clocks =<&clk IMX8MP_CLK_VPU_ROOT>;
+					};
+
+					pgc_vpu_g1: power-domain@20 {
+						#power-domain-cells = <0>;
+						power-domains = <&pgc_vpumix>;
+						reg = <IMX8MP_POWER_DOMAIN_VPU_G1>;
+						clocks = <&clk IMX8MP_CLK_VPU_G1_ROOT>;
+					};
+
+					pgc_vpu_g2: power-domain@21 {
+						#power-domain-cells = <0>;
+						power-domains = <&pgc_vpumix>;
+						reg = <IMX8MP_POWER_DOMAIN_VPU_G2>;
+						clocks = <&clk IMX8MP_CLK_VPU_G2_ROOT>;
+					};
+
+					pgc_vpu_vc8000e: power-domain@22 {
+						#power-domain-cells = <0>;
+						power-domains = <&pgc_vpumix>;
+						reg = <IMX8MP_POWER_DOMAIN_VPU_VC8000E>;
+						clocks = <&clk IMX8MP_CLK_VPU_VC8KE_ROOT>;
+					};
+				};
+			};
 		};
 
 		aips2: bus@30400000 {
@@ -459,7 +649,7 @@
 				clocks = <&clk IMX8MP_CLK_PWM1_ROOT>,
 					 <&clk IMX8MP_CLK_PWM1_ROOT>;
 				clock-names = "ipg", "per";
-				#pwm-cells = <2>;
+				#pwm-cells = <3>;
 				status = "disabled";
 			};
 
@@ -470,7 +660,7 @@
 				clocks = <&clk IMX8MP_CLK_PWM2_ROOT>,
 					 <&clk IMX8MP_CLK_PWM2_ROOT>;
 				clock-names = "ipg", "per";
-				#pwm-cells = <2>;
+				#pwm-cells = <3>;
 				status = "disabled";
 			};
 
@@ -481,7 +671,7 @@
 				clocks = <&clk IMX8MP_CLK_PWM3_ROOT>,
 					 <&clk IMX8MP_CLK_PWM3_ROOT>;
 				clock-names = "ipg", "per";
-				#pwm-cells = <2>;
+				#pwm-cells = <3>;
 				status = "disabled";
 			};
 
@@ -492,7 +682,7 @@
 				clocks = <&clk IMX8MP_CLK_PWM4_ROOT>,
 					 <&clk IMX8MP_CLK_PWM4_ROOT>;
 				clock-names = "ipg", "per";
-				#pwm-cells = <2>;
+				#pwm-cells = <3>;
 				status = "disabled";
 			};
 
@@ -585,6 +775,8 @@
 				clocks = <&clk IMX8MP_CLK_UART2_ROOT>,
 					 <&clk IMX8MP_CLK_UART2_ROOT>;
 				clock-names = "ipg", "per";
+				dmas = <&sdma1 24 4 0>, <&sdma1 25 4 0>;
+				dma-names = "rx", "tx";
 				status = "disabled";
 			};
 
@@ -633,6 +825,7 @@
 					compatible = "fsl,sec-v4.0-job-ring";
 					reg = <0x1000 0x1000>;
 					interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>;
+					status = "disabled";
 				};
 
 				sec_jr1: jr@2000 {
@@ -737,7 +930,7 @@
 			};
 
 			usdhc1: mmc@30b40000 {
-				compatible = "fsl,imx8mp-usdhc", "fsl,imx7d-usdhc";
+				compatible = "fsl,imx8mp-usdhc", "fsl,imx8mm-usdhc", "fsl,imx7d-usdhc";
 				reg = <0x30b40000 0x10000>;
 				interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clk IMX8MP_CLK_DUMMY>,
@@ -745,13 +938,13 @@
 					 <&clk IMX8MP_CLK_USDHC1_ROOT>;
 				clock-names = "ipg", "ahb", "per";
 				fsl,tuning-start-tap = <20>;
-				fsl,tuning-step= <2>;
+				fsl,tuning-step = <2>;
 				bus-width = <4>;
 				status = "disabled";
 			};
 
 			usdhc2: mmc@30b50000 {
-				compatible = "fsl,imx8mp-usdhc", "fsl,imx7d-usdhc";
+				compatible = "fsl,imx8mp-usdhc", "fsl,imx8mm-usdhc", "fsl,imx7d-usdhc";
 				reg = <0x30b50000 0x10000>;
 				interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clk IMX8MP_CLK_DUMMY>,
@@ -759,13 +952,13 @@
 					 <&clk IMX8MP_CLK_USDHC2_ROOT>;
 				clock-names = "ipg", "ahb", "per";
 				fsl,tuning-start-tap = <20>;
-				fsl,tuning-step= <2>;
+				fsl,tuning-step = <2>;
 				bus-width = <4>;
 				status = "disabled";
 			};
 
 			usdhc3: mmc@30b60000 {
-				compatible = "fsl,imx8mp-usdhc", "fsl,imx7d-usdhc";
+				compatible = "fsl,imx8mp-usdhc", "fsl,imx8mm-usdhc", "fsl,imx7d-usdhc";
 				reg = <0x30b60000 0x10000>;
 				interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&clk IMX8MP_CLK_DUMMY>,
@@ -773,7 +966,7 @@
 					 <&clk IMX8MP_CLK_USDHC3_ROOT>;
 				clock-names = "ipg", "ahb", "per";
 				fsl,tuning-start-tap = <20>;
-				fsl,tuning-step= <2>;
+				fsl,tuning-step = <2>;
 				bus-width = <4>;
 				status = "disabled";
 			};
@@ -832,7 +1025,6 @@
 				nvmem-cells = <&eth_mac1>;
 				nvmem-cell-names = "mac-address";
 				fsl,stop-mode = <&gpr 0x10 3>;
-				nvmem_macaddr_swap;
 				status = "disabled";
 			};
 
@@ -854,11 +1046,200 @@
 							 <&clk IMX8MP_SYS_PLL2_100M>,
 							 <&clk IMX8MP_SYS_PLL2_125M>;
 				assigned-clock-rates = <0>, <100000000>, <125000000>;
+				nvmem-cells = <&eth_mac2>;
+				nvmem-cell-names = "mac-address";
 				intf_mode = <&gpr 0x4>;
 				status = "disabled";
 			};
 		};
 
+		noc: interconnect@32700000 {
+			compatible = "fsl,imx8mp-noc", "fsl,imx8m-noc";
+			reg = <0x32700000 0x100000>;
+			clocks = <&clk IMX8MP_CLK_NOC>;
+			#interconnect-cells = <1>;
+			operating-points-v2 = <&noc_opp_table>;
+
+			noc_opp_table: opp-table {
+				compatible = "operating-points-v2";
+
+				opp-200M {
+					opp-hz = /bits/ 64 <200000000>;
+				};
+
+				opp-1000M {
+					opp-hz = /bits/ 64 <1000000000>;
+				};
+			};
+		};
+
+		aips4: bus@32c00000 {
+			compatible = "fsl,aips-bus", "simple-bus";
+			reg = <0x32c00000 0x400000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			media_blk_ctrl: blk-ctrl@32ec0000 {
+				compatible = "fsl,imx8mp-media-blk-ctrl",
+					     "syscon";
+				reg = <0x32ec0000 0x10000>;
+				power-domains = <&pgc_mediamix>,
+						<&pgc_mipi_phy1>,
+						<&pgc_mipi_phy1>,
+						<&pgc_mediamix>,
+						<&pgc_mediamix>,
+						<&pgc_mipi_phy2>,
+						<&pgc_mediamix>,
+						<&pgc_ispdwp>,
+						<&pgc_ispdwp>,
+						<&pgc_mipi_phy2>;
+				power-domain-names = "bus", "mipi-dsi1", "mipi-csi1",
+						     "lcdif1", "isi", "mipi-csi2",
+						     "lcdif2", "isp", "dwe",
+						     "mipi-dsi2";
+				interconnects =
+					<&noc IMX8MP_ICM_LCDIF_RD &noc IMX8MP_ICN_MEDIA>,
+					<&noc IMX8MP_ICM_LCDIF_WR &noc IMX8MP_ICN_MEDIA>,
+					<&noc IMX8MP_ICM_ISI0 &noc IMX8MP_ICN_MEDIA>,
+					<&noc IMX8MP_ICM_ISI1 &noc IMX8MP_ICN_MEDIA>,
+					<&noc IMX8MP_ICM_ISI2 &noc IMX8MP_ICN_MEDIA>,
+					<&noc IMX8MP_ICM_ISP0 &noc IMX8MP_ICN_MEDIA>,
+					<&noc IMX8MP_ICM_ISP1 &noc IMX8MP_ICN_MEDIA>,
+					<&noc IMX8MP_ICM_DWE &noc IMX8MP_ICN_MEDIA>;
+				interconnect-names = "lcdif-rd", "lcdif-wr", "isi0",
+						     "isi1", "isi2", "isp0", "isp1",
+						     "dwe";
+				clocks = <&clk IMX8MP_CLK_MEDIA_APB_ROOT>,
+					 <&clk IMX8MP_CLK_MEDIA_AXI_ROOT>,
+					 <&clk IMX8MP_CLK_MEDIA_CAM1_PIX_ROOT>,
+					 <&clk IMX8MP_CLK_MEDIA_CAM2_PIX_ROOT>,
+					 <&clk IMX8MP_CLK_MEDIA_DISP1_PIX_ROOT>,
+					 <&clk IMX8MP_CLK_MEDIA_DISP2_PIX_ROOT>,
+					 <&clk IMX8MP_CLK_MEDIA_ISP_ROOT>,
+					 <&clk IMX8MP_CLK_MEDIA_MIPI_PHY1_REF_ROOT>;
+				clock-names = "apb", "axi", "cam1", "cam2",
+					      "disp1", "disp2", "isp", "phy";
+
+				assigned-clocks = <&clk IMX8MP_CLK_MEDIA_AXI>,
+						  <&clk IMX8MP_CLK_MEDIA_APB>;
+				assigned-clock-parents = <&clk IMX8MP_SYS_PLL2_1000M>,
+							 <&clk IMX8MP_SYS_PLL1_800M>;
+				assigned-clock-rates = <500000000>, <200000000>;
+
+				#power-domain-cells = <1>;
+			};
+
+			pcie_phy: pcie-phy@32f00000 {
+				compatible = "fsl,imx8mp-pcie-phy";
+				reg = <0x32f00000 0x10000>;
+				resets = <&src IMX8MP_RESET_PCIEPHY>,
+					 <&src IMX8MP_RESET_PCIEPHY_PERST>;
+				reset-names = "pciephy", "perst";
+				power-domains = <&hsio_blk_ctrl IMX8MP_HSIOBLK_PD_PCIE_PHY>;
+				#phy-cells = <0>;
+				status = "disabled";
+			};
+
+			hsio_blk_ctrl: blk-ctrl@32f10000 {
+				compatible = "fsl,imx8mp-hsio-blk-ctrl", "syscon";
+				reg = <0x32f10000 0x24>;
+				clocks = <&clk IMX8MP_CLK_USB_ROOT>,
+					 <&clk IMX8MP_CLK_PCIE_ROOT>;
+				clock-names = "usb", "pcie";
+				power-domains = <&pgc_hsiomix>, <&pgc_hsiomix>,
+						<&pgc_usb1_phy>, <&pgc_usb2_phy>,
+						<&pgc_hsiomix>, <&pgc_pcie_phy>;
+				power-domain-names = "bus", "usb", "usb-phy1",
+						     "usb-phy2", "pcie", "pcie-phy";
+				interconnects = <&noc IMX8MP_ICM_NOC_PCIE &noc IMX8MP_ICN_HSIO>,
+						<&noc IMX8MP_ICM_USB1 &noc IMX8MP_ICN_HSIO>,
+						<&noc IMX8MP_ICM_USB2 &noc IMX8MP_ICN_HSIO>,
+						<&noc IMX8MP_ICM_PCIE &noc IMX8MP_ICN_HSIO>;
+				interconnect-names = "noc-pcie", "usb1", "usb2", "pcie";
+				#power-domain-cells = <1>;
+			};
+		};
+
+		pcie: pcie@33800000 {
+			compatible = "fsl,imx8mp-pcie";
+			reg = <0x33800000 0x400000>, <0x1ff00000 0x80000>;
+			reg-names = "dbi", "config";
+			#address-cells = <3>;
+			#size-cells = <2>;
+			device_type = "pci";
+			bus-range = <0x00 0xff>;
+			ranges =  <0x81000000 0 0x00000000 0x1ff80000 0 0x00010000>, /* downstream I/O 64KB */
+				  <0x82000000 0 0x18000000 0x18000000 0 0x07f00000>; /* non-prefetchable memory */
+			num-lanes = <1>;
+			num-viewport = <4>;
+			interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "msi";
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0x7>;
+			interrupt-map = <0 0 0 1 &gic GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>,
+					<0 0 0 2 &gic GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>,
+					<0 0 0 3 &gic GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>,
+					<0 0 0 4 &gic GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>;
+			fsl,max-link-speed = <3>;
+			linux,pci-domain = <0>;
+			power-domains = <&hsio_blk_ctrl IMX8MP_HSIOBLK_PD_PCIE>;
+			resets = <&src IMX8MP_RESET_PCIE_CTRL_APPS_EN>,
+				 <&src IMX8MP_RESET_PCIE_CTRL_APPS_TURNOFF>;
+			reset-names = "apps", "turnoff";
+			phys = <&pcie_phy>;
+			phy-names = "pcie-phy";
+			status = "disabled";
+		};
+
+		gpu3d: gpu@38000000 {
+			compatible = "vivante,gc";
+			reg = <0x38000000 0x8000>;
+			interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk IMX8MP_CLK_GPU3D_ROOT>,
+				 <&clk IMX8MP_CLK_GPU3D_SHADER_CORE>,
+				 <&clk IMX8MP_CLK_GPU_ROOT>,
+				 <&clk IMX8MP_CLK_GPU_AHB>;
+			clock-names = "core", "shader", "bus", "reg";
+			assigned-clocks = <&clk IMX8MP_CLK_GPU3D_CORE>,
+					  <&clk IMX8MP_CLK_GPU3D_SHADER_CORE>;
+			assigned-clock-parents = <&clk IMX8MP_SYS_PLL1_800M>,
+						 <&clk IMX8MP_SYS_PLL1_800M>;
+			assigned-clock-rates = <800000000>, <800000000>;
+			power-domains = <&pgc_gpu3d>;
+		};
+
+		gpu2d: gpu@38008000 {
+			compatible = "vivante,gc";
+			reg = <0x38008000 0x8000>;
+			interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk IMX8MP_CLK_GPU2D_ROOT>,
+				 <&clk IMX8MP_CLK_GPU_ROOT>,
+				 <&clk IMX8MP_CLK_GPU_AHB>;
+			clock-names = "core", "bus", "reg";
+			assigned-clocks = <&clk IMX8MP_CLK_GPU2D_CORE>;
+			assigned-clock-parents = <&clk IMX8MP_SYS_PLL1_800M>;
+			assigned-clock-rates = <800000000>;
+			power-domains = <&pgc_gpu2d>;
+		};
+
+		vpumix_blk_ctrl: blk-ctrl@38330000 {
+			compatible = "fsl,imx8mp-vpu-blk-ctrl", "syscon";
+			reg = <0x38330000 0x100>;
+			#power-domain-cells = <1>;
+			power-domains = <&pgc_vpumix>, <&pgc_vpu_g1>,
+					<&pgc_vpu_g2>, <&pgc_vpu_vc8000e>;
+			power-domain-names = "bus", "g1", "g2", "vc8000e";
+			clocks = <&clk IMX8MP_CLK_VPU_G1_ROOT>,
+				 <&clk IMX8MP_CLK_VPU_G2_ROOT>,
+				 <&clk IMX8MP_CLK_VPU_VC8KE_ROOT>;
+			clock-names = "g1", "g2", "vc8000e";
+			interconnects = <&noc IMX8MP_ICM_VPU_G1 &noc IMX8MP_ICN_VIDEO>,
+					<&noc IMX8MP_ICM_VPU_G2 &noc IMX8MP_ICN_VIDEO>,
+					<&noc IMX8MP_ICM_VPU_H1 &noc IMX8MP_ICN_VIDEO>;
+			interconnect-names = "g1", "g2", "vc8000e";
+		};
+
 		gic: interrupt-controller@38800000 {
 			compatible = "arm,gic-v3";
 			reg = <0x38800000 0x10000>,
@@ -869,6 +1250,12 @@
 			interrupt-parent = <&gic>;
 		};
 
+		edacmc: memory-controller@3d400000 {
+			compatible = "snps,ddrc-3.80a";
+			reg = <0x3d400000 0x400000>;
+			interrupts = <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
 		ddr-pmu@3d800000 {
 			compatible = "fsl,imx8mp-ddr-pmu", "fsl,imx8m-ddr-pmu";
 			reg = <0x3d800000 0x400000>;
@@ -882,17 +1269,20 @@
 			clock-names = "phy";
 			assigned-clocks = <&clk IMX8MP_CLK_USB_PHY_REF>;
 			assigned-clock-parents = <&clk IMX8MP_CLK_24M>;
+			power-domains = <&hsio_blk_ctrl IMX8MP_HSIOBLK_PD_USB_PHY1>;
 			#phy-cells = <0>;
 			status = "disabled";
 		};
 
 		usb3_0: usb@32f10100 {
 			compatible = "fsl,imx8mp-dwc3";
-			reg = <0x32f10100 0x8>;
+			reg = <0x32f10100 0x8>,
+			      <0x381f0000 0x20>;
 			clocks = <&clk IMX8MP_CLK_HSIO_ROOT>,
 				 <&clk IMX8MP_CLK_USB_ROOT>;
 			clock-names = "hsio", "suspend";
 			interrupts = <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>;
+			power-domains = <&hsio_blk_ctrl IMX8MP_HSIOBLK_PD_USB>;
 			#address-cells = <1>;
 			#size-cells = <1>;
 			dma-ranges = <0x40000000 0x40000000 0xc0000000>;
@@ -906,13 +1296,10 @@
 					 <&clk IMX8MP_CLK_USB_CORE_REF>,
 					 <&clk IMX8MP_CLK_USB_ROOT>;
 				clock-names = "bus_early", "ref", "suspend";
-				assigned-clocks = <&clk IMX8MP_CLK_HSIO_AXI>;
-				assigned-clock-parents = <&clk IMX8MP_SYS_PLL2_500M>;
-				assigned-clock-rates = <500000000>;
 				interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
 				phys = <&usb3_phy0>, <&usb3_phy0>;
 				phy-names = "usb2-phy", "usb3-phy";
-				snps,dis-u2-freeclk-exists-quirk;
+				snps,gfladj-refclk-lpm-sel-quirk;
 			};
 
 		};
@@ -924,16 +1311,20 @@
 			clock-names = "phy";
 			assigned-clocks = <&clk IMX8MP_CLK_USB_PHY_REF>;
 			assigned-clock-parents = <&clk IMX8MP_CLK_24M>;
+			power-domains = <&hsio_blk_ctrl IMX8MP_HSIOBLK_PD_USB_PHY2>;
 			#phy-cells = <0>;
+			status = "disabled";
 		};
 
 		usb3_1: usb@32f10108 {
 			compatible = "fsl,imx8mp-dwc3";
-			reg = <0x32f10108 0x8>;
+			reg = <0x32f10108 0x8>,
+			      <0x382f0000 0x20>;
 			clocks = <&clk IMX8MP_CLK_HSIO_ROOT>,
 				 <&clk IMX8MP_CLK_USB_ROOT>;
 			clock-names = "hsio", "suspend";
 			interrupts = <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>;
+			power-domains = <&hsio_blk_ctrl IMX8MP_HSIOBLK_PD_USB>;
 			#address-cells = <1>;
 			#size-cells = <1>;
 			dma-ranges = <0x40000000 0x40000000 0xc0000000>;
@@ -947,13 +1338,10 @@
 					 <&clk IMX8MP_CLK_USB_CORE_REF>,
 					 <&clk IMX8MP_CLK_USB_ROOT>;
 				clock-names = "bus_early", "ref", "suspend";
-				assigned-clocks = <&clk IMX8MP_CLK_HSIO_AXI>;
-				assigned-clock-parents = <&clk IMX8MP_SYS_PLL2_500M>;
-				assigned-clock-rates = <500000000>;
 				interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
 				phys = <&usb3_phy1>, <&usb3_phy1>;
 				phy-names = "usb2-phy", "usb3-phy";
-				snps,dis-u2-freeclk-exists-quirk;
+				snps,gfladj-refclk-lpm-sel-quirk;
 			};
 		};
 
diff --git a/arch/arm64/boot/dts/freescale/imx8mq-evk.dts b/arch/arm64/boot/dts/freescale/imx8mq-evk.dts
index b83df77195ec..82387b9cb800 100644
--- a/arch/arm64/boot/dts/freescale/imx8mq-evk.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mq-evk.dts
@@ -27,6 +27,17 @@
 		clock-frequency = <100000000>;
 	};
 
+	reg_pcie1: regulator-pcie {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_pcie1_reg>;
+		regulator-name = "MPCIE_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio5 10 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
 	reg_usdhc2_vmmc: regulator-vsd-3v3 {
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_reg_usdhc2>;
@@ -60,12 +71,36 @@
 		linux,autosuspend-period = <125>;
 	};
 
+	audio_codec_bt_sco: audio-codec-bt-sco {
+		compatible = "linux,bt-sco";
+		#sound-dai-cells = <1>;
+	};
+
 	wm8524: audio-codec {
 		#sound-dai-cells = <0>;
 		compatible = "wlf,wm8524";
 		wlf,mute-gpios = <&gpio1 8 GPIO_ACTIVE_LOW>;
 	};
 
+	sound-bt-sco {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "bt-sco-audio";
+		simple-audio-card,format = "dsp_a";
+		simple-audio-card,bitclock-inversion;
+		simple-audio-card,frame-master = <&btcpu>;
+		simple-audio-card,bitclock-master = <&btcpu>;
+
+		btcpu: simple-audio-card,cpu {
+			sound-dai = <&sai3>;
+			dai-tdm-slot-num = <2>;
+			dai-tdm-slot-width = <16>;
+		};
+
+		simple-audio-card,codec {
+			sound-dai = <&audio_codec_bt_sco 1>;
+		};
+	};
+
 	sound-wm8524 {
 		compatible = "simple-audio-card";
 		simple-audio-card,name = "wm8524-audio";
@@ -123,6 +158,7 @@
 
 &ddrc {
 	operating-points-v2 = <&ddrc_opp_table>;
+	status = "okay";
 
 	ddrc_opp_table: opp-table {
 		compatible = "operating-points-v2";
@@ -169,6 +205,11 @@
 			reg = <0>;
 			reset-gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
 			reset-assert-us = <10000>;
+			qca,disable-smarteee;
+			vddio-supply = <&vddh>;
+
+			vddh: vddh-regulator {
+			};
 		};
 	};
 };
@@ -322,10 +363,28 @@
 	status = "okay";
 };
 
+&pcie1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pcie1>;
+	reset-gpio = <&gpio5 12 GPIO_ACTIVE_LOW>;
+	clocks = <&clk IMX8MQ_CLK_PCIE2_ROOT>,
+		 <&clk IMX8MQ_CLK_PCIE2_AUX>,
+		 <&clk IMX8MQ_CLK_PCIE2_PHY>,
+		 <&pcie0_refclk>;
+	clock-names = "pcie", "pcie_aux", "pcie_phy", "pcie_bus";
+	vpcie-supply = <&reg_pcie1>;
+	vph-supply = <&vgen5_reg>;
+	status = "okay";
+};
+
 &pgc_gpu {
 	power-supply = <&sw1a_reg>;
 };
 
+&pgc_vpu {
+	power-supply = <&sw1c_reg>;
+};
+
 &qspi0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_qspi>;
@@ -351,6 +410,16 @@
 	status = "okay";
 };
 
+&sai3 {
+	#sound-dai-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sai3>;
+	assigned-clocks = <&clk IMX8MQ_CLK_SAI3>;
+	assigned-clock-parents = <&clk IMX8MQ_AUDIO_PLL1_OUT>;
+	assigned-clock-rates = <24576000>;
+	status = "okay";
+};
+
 &snvs_pwrkey {
 	status = "okay";
 };
@@ -473,6 +542,19 @@
 		>;
 	};
 
+	pinctrl_pcie1: pcie1grp {
+		fsl,pins = <
+			MX8MQ_IOMUXC_I2C4_SDA_PCIE2_CLKREQ_B		0x76
+			MX8MQ_IOMUXC_ECSPI2_MISO_GPIO5_IO12		0x16
+		>;
+	};
+
+	pinctrl_pcie1_reg: pcie1reggrp {
+		fsl,pins = <
+			MX8MQ_IOMUXC_ECSPI2_SCLK_GPIO5_IO10		0x16
+		>;
+	};
+
 	pinctrl_qspi: qspigrp {
 		fsl,pins = <
 			MX8MQ_IOMUXC_NAND_ALE_QSPI_A_SCLK	0x82
@@ -500,6 +582,15 @@
 		>;
 	};
 
+	pinctrl_sai3: sai3grp {
+		fsl,pins = <
+			MX8MQ_IOMUXC_SAI3_TXFS_SAI3_TX_SYNC     0xd6
+			MX8MQ_IOMUXC_SAI3_TXC_SAI3_TX_BCLK      0xd6
+			MX8MQ_IOMUXC_SAI3_TXD_SAI3_TX_DATA0     0xd6
+			MX8MQ_IOMUXC_SAI3_RXD_SAI3_RX_DATA0     0xd6
+		>;
+	};
+
 	pinctrl_spdif1: spdif1grp {
 		fsl,pins = <
 			MX8MQ_IOMUXC_SPDIF_TX_SPDIF1_OUT	0xd6
diff --git a/arch/arm64/boot/dts/freescale/imx8mq-kontron-pitx-imx8m.dts b/arch/arm64/boot/dts/freescale/imx8mq-kontron-pitx-imx8m.dts
index 564746d5000d..a91c136797f6 100644
--- a/arch/arm64/boot/dts/freescale/imx8mq-kontron-pitx-imx8m.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mq-kontron-pitx-imx8m.dts
@@ -311,7 +311,7 @@
 &uart3 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart3>;
-	fsl,uart-has-rtscts;
+	uart-has-rtscts;
 	assigned-clocks = <&clk IMX8MQ_CLK_UART3>;
 	assigned-clock-parents = <&clk IMX8MQ_SYS1_PLL_80M>;
 	status = "okay";
diff --git a/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts b/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts
index 622f3787a186..6445c6b90b5b 100644
--- a/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts
@@ -18,7 +18,7 @@
 	backlight_dsi: backlight-dsi {
 		compatible = "pwm-backlight";
 		/* 200 Hz for the PAM2841 */
-		pwms = <&pwm1 0 5000000>;
+		pwms = <&pwm1 0 5000000 0>;
 		brightness-levels = <0 100>;
 		num-interpolated-steps = <100>;
 		/* Default brightness level (index into the array defined by */
@@ -36,21 +36,21 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gpio_keys>;
 
-		btn1 {
+		button-1 {
 			label = "VOL_UP";
 			gpios = <&gpio4 21 GPIO_ACTIVE_LOW>;
 			wakeup-source;
 			linux,code = <KEY_VOLUMEUP>;
 		};
 
-		btn2 {
+		button-2 {
 			label = "VOL_DOWN";
 			gpios = <&gpio4 22 GPIO_ACTIVE_LOW>;
 			wakeup-source;
 			linux,code = <KEY_VOLUMEDOWN>;
 		};
 
-		wwan-wake {
+		button-3 {
 			label = "WWAN_WAKE";
 			gpios = <&gpio3 8 GPIO_ACTIVE_LOW>;
 			interrupt-parent = <&gpio3>;
diff --git a/arch/arm64/boot/dts/freescale/imx8mq-librem5-r3.dts b/arch/arm64/boot/dts/freescale/imx8mq-librem5-r3.dts
index cd3c3edd48fa..4533a84fb0b9 100644
--- a/arch/arm64/boot/dts/freescale/imx8mq-librem5-r3.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mq-librem5-r3.dts
@@ -1,14 +1,9 @@
 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
-// Copyright (C) 2020 Purism SPC <kernel@puri.sm>
+// Copyright (C) 2021 Purism SPC <kernel@puri.sm>
 
 /dts-v1/;
 
-#include "imx8mq-librem5.dtsi"
-
-/ {
-	model = "Purism Librem 5r3";
-	compatible = "purism,librem5r3", "purism,librem5", "fsl,imx8mq";
-};
+#include "imx8mq-librem5-r3.dtsi"
 
 &a53_opp_table {
 	opp-1000000000 {
@@ -16,22 +11,6 @@
 	};
 };
 
-&accel_gyro {
-	mount-matrix =  "1",  "0",  "0",
-			"0",  "1",  "0",
-			"0",  "0", "-1";
-};
-
-&bq25895 {
-	ti,battery-regulation-voltage = <4200000>; /* uV */
-	ti,charge-current = <1500000>; /* uA */
-	ti,termination-current = <144000>;  /* uA */
-};
-
 &buck3_reg {
 	regulator-always-on;
 };
-
-&proximity {
-	proximity-near-level = <25>;
-};
diff --git a/arch/arm64/boot/dts/freescale/imx8mq-librem5-r3.dtsi b/arch/arm64/boot/dts/freescale/imx8mq-librem5-r3.dtsi
new file mode 100644
index 000000000000..e4f8b47cce4f
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mq-librem5-r3.dtsi
@@ -0,0 +1,45 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+// Copyright (C) 2021 Purism SPC <kernel@puri.sm>
+
+/dts-v1/;
+
+/*
+ * This file describes hardware that is shared among r3 ("Dogwood") and
+ * later revisions of the Librem 5 so it has to be included in dts there.
+ */
+
+#include "imx8mq-librem5.dtsi"
+
+/ {
+	model = "Purism Librem 5r3";
+	compatible = "purism,librem5r3", "purism,librem5", "fsl,imx8mq";
+};
+
+&accel_gyro {
+	mount-matrix =  "1",  "0",  "0",
+			"0",  "1",  "0",
+			"0",  "0", "-1";
+};
+
+&bq25895 {
+	ti,battery-regulation-voltage = <4200000>; /* uV */
+	ti,charge-current = <1500000>; /* uA */
+	ti,termination-current = <144000>;  /* uA */
+};
+
+&camera_front {
+	pinctrl-0 = <&pinctrl_csi1>, <&pinctrl_r3_camera_pwr>;
+	shutdown-gpios = <&gpio5 4 GPIO_ACTIVE_LOW>;
+};
+
+&iomuxc {
+	pinctrl_r3_camera_pwr: r3camerapwrgrp {
+		fsl,pins = <
+			MX8MQ_IOMUXC_SPDIF_RX_GPIO5_IO4		0x83
+		>;
+	};
+};
+
+&proximity {
+	proximity-near-level = <25>;
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mq-librem5-r4.dts b/arch/arm64/boot/dts/freescale/imx8mq-librem5-r4.dts
index cbfb49aa2563..1056b7981bdb 100644
--- a/arch/arm64/boot/dts/freescale/imx8mq-librem5-r4.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mq-librem5-r4.dts
@@ -1,35 +1,27 @@
 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
-// Copyright (C) 2020 Purism SPC <kernel@puri.sm>
+// Copyright (C) 2021 Purism SPC <kernel@puri.sm>
 
 /dts-v1/;
 
-#include "imx8mq-librem5.dtsi"
+#include "imx8mq-librem5-r3.dtsi"
 
 / {
 	model = "Purism Librem 5r4";
 	compatible = "purism,librem5r4", "purism,librem5", "fsl,imx8mq";
 };
 
-&accel_gyro {
-	mount-matrix =  "1",  "0",  "0",
-			"0",  "1",  "0",
-			"0",  "0", "-1";
-};
-
 &bat {
 	maxim,rsns-microohm = <1667>;
 };
 
-&bq25895 {
-	ti,battery-regulation-voltage = <4200000>; /* uV */
-	ti,charge-current = <1500000>; /* uA */
-	ti,termination-current = <144000>;  /* uA */
-};
-
 &led_backlight {
 	led-max-microamp = <25000>;
 };
 
+&lcd_panel {
+	compatible = "ys,ys57pss36bh5gq";
+};
+
 &proximity {
 	proximity-near-level = <10>;
 };
diff --git a/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi b/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi
index 60d47c71499b..ae08556b2ef2 100644
--- a/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi
@@ -7,6 +7,7 @@
 
 #include "dt-bindings/input/input.h"
 #include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/leds/common.h>
 #include "dt-bindings/pwm/pwm.h"
 #include "dt-bindings/usb/pd.h"
 #include "imx8mq.dtsi"
@@ -14,6 +15,7 @@
 / {
 	model = "Purism Librem 5";
 	compatible = "purism,librem5", "fsl,imx8mq";
+	chassis-type = "handset";
 
 	backlight_dsi: backlight-dsi {
 		compatible = "led-backlight";
@@ -36,18 +38,45 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_keys>;
 
-		vol-down {
+		key-vol-down {
 			label = "VOL_DOWN";
 			gpios = <&gpio1 17 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_VOLUMEDOWN>;
 			debounce-interval = <50>;
+			wakeup-source;
 		};
 
-		vol-up {
+		key-vol-up {
 			label = "VOL_UP";
 			gpios = <&gpio1 16 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_VOLUMEUP>;
 			debounce-interval = <50>;
+			wakeup-source;
+		};
+	};
+
+	led-controller {
+		compatible = "pwm-leds";
+
+		led-0 {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_BLUE>;
+			max-brightness = <248>;
+			pwms = <&pwm2 0 50000 0>;
+		};
+
+		led-1 {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_GREEN>;
+			max-brightness = <248>;
+			pwms = <&pwm4 0 50000 0>;
+		};
+
+		led-2 {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_RED>;
+			max-brightness = <248>;
+			pwms = <&pwm3 0 50000 0>;
 		};
 	};
 
@@ -62,6 +91,40 @@
 		enable-active-high;
 	};
 
+	/*
+	 * the pinctrl for reg_csi_1v8 and reg_vcam_1v8 is added to the PMIC
+	 * since we can't have it twice in the 2 different regulator nodes.
+	 */
+	reg_csi_1v8: regulator-csi-1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "CAMERA_VDDIO_1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&reg_vdd_3v3>;
+		gpio = <&gpio1 0 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	/* controlled by the CAMERA_POWER_KEY HKS */
+	reg_vcam_1v2: regulator-vcam-1v2 {
+		compatible = "regulator-fixed";
+		regulator-name = "CAMERA_VDDD_1V2";
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <1200000>;
+		vin-supply = <&reg_vdd_1v8>;
+		enable-active-high;
+	};
+
+	reg_vcam_2v8: regulator-vcam-2v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "CAMERA_VDDA_2V8";
+		regulator-min-microvolt = <2800000>;
+		regulator-max-microvolt = <2800000>;
+		vin-supply = <&reg_vdd_3v3>;
+		gpio = <&gpio1 0 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
 	reg_gnss: regulator-gnss {
 		compatible = "regulator-fixed";
 		pinctrl-names = "default";
@@ -237,8 +300,13 @@
 	cpu-supply = <&buck2_reg>;
 };
 
+&csi1 {
+	status = "okay";
+};
+
 &ddrc {
 	operating-points-v2 = <&ddrc_opp_table>;
+	status = "okay";
 
 	ddrc_opp_table: opp-table {
 		compatible = "operating-points-v2";
@@ -283,15 +351,10 @@
 		};
 
 		partition@30000 {
-			label = "protected1";
-			reg = <0x30000 0x10000>;
+			label = "firmware";
+			reg = <0x30000 0x1d0000>;
 			read-only;
 		};
-
-		partition@40000 {
-			label = "rw";
-			reg = <0x40000 0x1C0000>;
-		};
 	};
 };
 
@@ -329,12 +392,24 @@
 		>;
 	};
 
+	pinctrl_camera_pwr: camerapwrgrp {
+		fsl,pins = <
+			/* CAMERA_PWR_EN_3V3 */
+			MX8MQ_IOMUXC_GPIO1_IO00_GPIO1_IO0	0x83
+		>;
+	};
+
+	pinctrl_csi1: csi1grp {
+		fsl,pins = <
+			/* CSI1_NRST */
+			MX8MQ_IOMUXC_ENET_RXC_GPIO1_IO25	0x83
+		>;
+	};
+
 	pinctrl_charger_in: chargeringrp {
 		fsl,pins = <
 			/* CHRG_INT */
 			MX8MQ_IOMUXC_NAND_CE2_B_GPIO3_IO3	0x80
-			/* CHG_STATUS_B */
-			MX8MQ_IOMUXC_NAND_ALE_GPIO3_IO0		0x80
 		>;
 	};
 
@@ -698,6 +773,10 @@
 		interrupt-names = "irq";
 
 		connector {
+			compatible = "usb-c-connector";
+			label = "USB-C";
+			data-role = "dual";
+
 			ports {
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -725,7 +804,7 @@
 		compatible = "rohm,bd71837";
 		reg = <0x4b>;
 		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_pmic>;
+		pinctrl-0 = <&pinctrl_pmic>, <&pinctrl_camera_pwr>;
 		clocks = <&pmic_osc>;
 		clock-names = "osc";
 		clock-output-names = "pmic_clk";
@@ -958,6 +1037,31 @@
 		>;
 	};
 
+	camera_front: camera@20 {
+		compatible = "hynix,hi846";
+		reg = <0x20>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_csi1>;
+		clocks = <&clk IMX8MQ_CLK_CLKO2>;
+		assigned-clocks = <&clk IMX8MQ_CLK_CLKO2>;
+		assigned-clock-rates = <25000000>;
+		reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
+		vdda-supply = <&reg_vcam_2v8>;
+		vddd-supply = <&reg_vcam_1v2>;
+		vddio-supply = <&reg_csi_1v8>;
+		rotation = <90>;
+		orientation = <0>;
+
+		port {
+			camera1_ep: endpoint {
+				data-lanes = <1 2>;
+				link-frequencies = /bits/ 64
+					<80000000 200000000 300000000>;
+				remote-endpoint = <&mipi1_sensor_ep>;
+			};
+		};
+	};
+
 	backlight@36 {
 		compatible = "ti,lm36922";
 		reg = <0x36>;
@@ -996,6 +1100,12 @@
 	pinctrl-0 = <&pinctrl_i2c4>;
 	status = "okay";
 
+	vcm@c {
+		compatible = "dongwoon,dw9714";
+		reg = <0x0c>;
+		vcc-supply = <&reg_csi_1v8>;
+	};
+
 	bat: fuel-gauge@36 {
 		compatible = "maxim,max17055";
 		reg = <0x36>;
@@ -1003,6 +1113,7 @@
 		interrupts = <20 IRQ_TYPE_LEVEL_LOW>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gauge>;
+		power-supplies = <&bq25895>;
 		maxim,over-heat-temp = <700>;
 		maxim,over-volt = <4500>;
 		maxim,rsns-microohm = <5000>;
@@ -1019,7 +1130,7 @@
 		ti,precharge-current = <130000>; /* uA */
 		ti,minimum-sys-voltage = <3700000>; /* uV */
 		ti,boost-voltage = <5000000>; /* uV */
-		ti,boost-max-current = <500000>; /* uA */
+		ti,boost-max-current = <1500000>; /* uA */
 		ti,use-vinmin-threshold = <1>; /* enable VINDPM */
 		ti,vinmin-threshold = <3900000>; /* uV */
 		monitored-battery = <&bat>;
@@ -1031,6 +1142,21 @@
 	status = "okay";
 };
 
+&mipi_csi1 {
+	status = "okay";
+
+	ports {
+		port@0 {
+			reg = <0>;
+
+			mipi1_sensor_ep: endpoint {
+				remote-endpoint = <&camera1_ep>;
+				data-lanes = <1 2>;
+			};
+		};
+	};
+};
+
 &mipi_dsi {
 	#address-cells = <1>;
 	#size-cells = <0>;
@@ -1174,6 +1300,7 @@
 	#size-cells = <0>;
 	dr_mode = "otg";
 	snps,dis_u3_susphy_quirk;
+	usb-role-switch;
 	status = "okay";
 
 	port@0 {
diff --git a/arch/arm64/boot/dts/freescale/imx8mq-mnt-reform2.dts b/arch/arm64/boot/dts/freescale/imx8mq-mnt-reform2.dts
index 4f2db6197b39..055031bba8c4 100644
--- a/arch/arm64/boot/dts/freescale/imx8mq-mnt-reform2.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mq-mnt-reform2.dts
@@ -12,6 +12,31 @@
 / {
 	model = "MNT Reform 2";
 	compatible = "mntre,reform2", "boundary,imx8mq-nitrogen8m-som", "fsl,imx8mq";
+	chassis-type = "laptop";
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_backlight>;
+		pwms = <&pwm2 0 10000 0>;
+		power-supply = <&reg_main_usb>;
+		enable-gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>;
+		brightness-levels = <0 32 64 128 160 200 255>;
+		default-brightness-level = <6>;
+	};
+
+	panel {
+		compatible = "innolux,n125hce-gn1", "simple-panel";
+		power-supply = <&reg_main_3v3>;
+		backlight = <&backlight>;
+		no-hpd;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&edp_bridge_out>;
+			};
+		};
+	};
 
 	pcie1_refclk: clock-pcie1-refclk {
 		compatible = "fixed-clock";
@@ -41,6 +66,22 @@
 		vin-supply = <&reg_main_5v>;
 	};
 
+	reg_main_1v8: regulator-main-1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&reg_main_3v3>;
+	};
+
+	reg_main_1v2: regulator-main-1v2 {
+		compatible = "regulator-fixed";
+		regulator-name = "1V2";
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <1200000>;
+		vin-supply = <&reg_main_5v>;
+	};
+
 	sound {
 		compatible = "fsl,imx-audio-wm8960";
 		audio-cpu = <&sai2>;
@@ -60,6 +101,13 @@
 	};
 };
 
+&dphy {
+	assigned-clocks = <&clk IMX8MQ_CLK_DSI_PHY_REF>;
+	assigned-clock-parents = <&clk IMX8MQ_SYS1_PLL_800M>;
+	assigned-clock-rates = <25000000>;
+	status = "okay";
+};
+
 &fec1 {
 	status = "okay";
 };
@@ -83,6 +131,67 @@
 	};
 };
 
+&i2c4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c4>;
+	clock-frequency = <400000>;
+	status = "okay";
+
+	edp_bridge: bridge@2c {
+		compatible = "ti,sn65dsi86";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_edp_bridge>;
+		reg = <0x2c>;
+		enable-gpios = <&gpio3 20 GPIO_ACTIVE_HIGH>;
+		vccio-supply = <&reg_main_1v8>;
+		vpll-supply = <&reg_main_1v8>;
+		vcca-supply = <&reg_main_1v2>;
+		vcc-supply = <&reg_main_1v2>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				edp_bridge_in: endpoint {
+					remote-endpoint = <&mipi_dsi_out>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				edp_bridge_out: endpoint {
+					remote-endpoint = <&panel_in>;
+				};
+			};
+		};
+	};
+};
+
+&lcdif {
+	assigned-clocks = <&clk IMX8MQ_CLK_LCDIF_PIXEL>;
+	assigned-clock-parents = <&clk IMX8MQ_SYS1_PLL_800M>;
+	/delete-property/assigned-clock-rates;
+	status = "okay";
+};
+
+&mipi_dsi {
+	status = "okay";
+
+	ports {
+		port@1 {
+			reg = <1>;
+
+			mipi_dsi_out: endpoint {
+				remote-endpoint = <&edp_bridge_in>;
+			};
+		};
+	};
+};
+
 &pcie1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pcie1>;
@@ -95,6 +204,12 @@
 	status = "okay";
 };
 
+&pwm2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm2>;
+	status = "okay";
+};
+
 &reg_1p8v {
 	vin-supply = <&reg_main_5v>;
 };
@@ -168,10 +283,29 @@
 };
 
 &iomuxc {
+	pinctrl_backlight: backlightgrp {
+		fsl,pins = <
+			MX8MQ_IOMUXC_GPIO1_IO10_GPIO1_IO10		0x3
+		>;
+	};
+
+	pinctrl_edp_bridge: edpbridgegrp {
+		fsl,pins = <
+			MX8MQ_IOMUXC_SAI5_RXC_GPIO3_IO20		0x1
+		>;
+	};
+
 	pinctrl_i2c3: i2c3grp {
 		fsl,pins = <
-			MX8MQ_IOMUXC_I2C3_SCL_I2C3_SCL			0x4000007f
-			MX8MQ_IOMUXC_I2C3_SDA_I2C3_SDA			0x4000007f
+			MX8MQ_IOMUXC_I2C3_SCL_I2C3_SCL			0x40000022
+			MX8MQ_IOMUXC_I2C3_SDA_I2C3_SDA			0x40000022
+		>;
+	};
+
+	pinctrl_i2c4: i2c4grp {
+		fsl,pins = <
+			MX8MQ_IOMUXC_I2C4_SCL_I2C4_SCL			0x40000022
+			MX8MQ_IOMUXC_I2C4_SDA_I2C4_SDA			0x40000022
 		>;
 	};
 
@@ -181,6 +315,12 @@
 		>;
 	};
 
+	pinctrl_pwm2: pwm2grp {
+		fsl,pins = <
+			MX8MQ_IOMUXC_SPDIF_RX_PWM2_OUT			0x3
+		>;
+	};
+
 	pinctrl_sai2: sai2grp {
 		fsl,pins = <
 			MX8MQ_IOMUXC_SAI2_RXD0_SAI2_RX_DATA0		0xd6
diff --git a/arch/arm64/boot/dts/freescale/imx8mq-nitrogen-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mq-nitrogen-som.dtsi
index 36fc428ebe30..395f77b5aca7 100644
--- a/arch/arm64/boot/dts/freescale/imx8mq-nitrogen-som.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mq-nitrogen-som.dtsi
@@ -69,6 +69,9 @@
 			reg = <4>;
 			interrupt-parent = <&gpio1>;
 			interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+			reset-gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <10000>;
+			reset-deassert-us = <300>;
 		};
 	};
 };
@@ -191,20 +194,20 @@
 			MX8MQ_IOMUXC_ENET_TD2_ENET1_RGMII_TD2		0x1f
 			MX8MQ_IOMUXC_ENET_TD3_ENET1_RGMII_TD3		0x1f
 			MX8MQ_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL	0x91
-			MX8MQ_IOMUXC_ENET_RXC_ENET1_RGMII_RXC		0x91
+			MX8MQ_IOMUXC_ENET_RXC_ENET1_RGMII_RXC		0xd1
 			MX8MQ_IOMUXC_ENET_RD0_ENET1_RGMII_RD0		0x91
 			MX8MQ_IOMUXC_ENET_RD1_ENET1_RGMII_RD1		0x91
 			MX8MQ_IOMUXC_ENET_RD2_ENET1_RGMII_RD2		0x91
-			MX8MQ_IOMUXC_ENET_RD3_ENET1_RGMII_RD3		0x91
-			MX8MQ_IOMUXC_GPIO1_IO09_GPIO1_IO9		0x19
-			MX8MQ_IOMUXC_GPIO1_IO11_GPIO1_IO11		0x59
+			MX8MQ_IOMUXC_ENET_RD3_ENET1_RGMII_RD3		0xd1
+			MX8MQ_IOMUXC_GPIO1_IO09_GPIO1_IO9		0x1
+			MX8MQ_IOMUXC_GPIO1_IO11_GPIO1_IO11		0x41
 		>;
 	};
 
 	pinctrl_i2c1: i2c1grp {
 		fsl,pins = <
-			MX8MQ_IOMUXC_I2C1_SCL_I2C1_SCL			0x4000007f
-			MX8MQ_IOMUXC_I2C1_SDA_I2C1_SDA			0x4000007f
+			MX8MQ_IOMUXC_I2C1_SCL_I2C1_SCL			0x40000022
+			MX8MQ_IOMUXC_I2C1_SDA_I2C1_SDA			0x40000022
 		>;
 	};
 
diff --git a/arch/arm64/boot/dts/freescale/imx8mq-nitrogen.dts b/arch/arm64/boot/dts/freescale/imx8mq-nitrogen.dts
index f70fb32b96b0..9dda2a1554c3 100644
--- a/arch/arm64/boot/dts/freescale/imx8mq-nitrogen.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mq-nitrogen.dts
@@ -26,7 +26,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gpio_keys>;
 
-		power {
+		button-power {
 			label = "Power Button";
 			gpios = <&gpio1 7 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
@@ -152,7 +152,7 @@
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_reg_arm_dram>;
 				reg = <0x60>;
-				regulator-min-microvolt =  <900000>;
+				regulator-min-microvolt = <900000>;
 				regulator-max-microvolt = <1000000>;
 				regulator-always-on;
 				vsel-gpios = <&gpio3 24 GPIO_ACTIVE_HIGH>;
@@ -186,7 +186,7 @@
 				pinctrl-names = "default";
 				pinctrl-0 = <&pinctrl_reg_soc_gpu_vpu>;
 				reg = <0x60>;
-				regulator-min-microvolt =  <900000>;
+				regulator-min-microvolt = <900000>;
 				regulator-max-microvolt = <1000000>;
 				regulator-always-on;
 				vsel-gpios = <&gpio2 20 GPIO_ACTIVE_HIGH>;
diff --git a/arch/arm64/boot/dts/freescale/imx8mq-tqma8mq-mba8mx.dts b/arch/arm64/boot/dts/freescale/imx8mq-tqma8mq-mba8mx.dts
new file mode 100644
index 000000000000..d7660eab68b9
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mq-tqma8mq-mba8mx.dts
@@ -0,0 +1,349 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2019-2021 TQ-Systems GmbH
+ */
+
+/dts-v1/;
+
+#include "imx8mq-tqma8mq.dtsi"
+#include "mba8mx.dtsi"
+
+/ {
+	model = "TQ-Systems GmbH i.MX8MQ TQMa8MQ on MBa8Mx";
+	compatible = "tq,imx8mq-tqma8mq-mba8mx", "tq,imx8mq-tqma8mq", "fsl,imx8mq";
+
+	aliases {
+		eeprom0 = &eeprom3;
+		mmc0 = &usdhc1;
+		mmc1 = &usdhc2;
+		rtc0 = &pcf85063;
+		rtc1 = &snvs_rtc;
+	};
+
+	extcon_usbotg: extcon-usbotg0 {
+		compatible = "linux,extcon-usb-gpio";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usbcon0>;
+		id-gpio = <&gpio1 10 GPIO_ACTIVE_HIGH>;
+	};
+
+	pcie0_refclk: pcie0-refclk {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <100000000>;
+	};
+
+	pcie1_refclk: pcie1-refclk {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <100000000>;
+	};
+
+	reg_otg_vbus: regulator-otg-vbus {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_regotgvbus>;
+		regulator-name = "MBA8MQ_OTG_VBUS";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	reg_usdhc2_vmmc: regulator-vmmc {
+		compatible = "regulator-fixed";
+		regulator-name = "VSD_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+};
+
+&btn2 {
+	gpios = <&gpio3 17 GPIO_ACTIVE_LOW>;
+};
+
+&gpio_leds {
+	led3 {
+		label = "led3";
+		gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&i2c1 {
+	expander2: gpio@25 {
+		compatible = "nxp,pca9555";
+		reg = <0x25>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		vcc-supply = <&reg_vcc_3v3>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_expander>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <9 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+
+		mpcie-rst-hog {
+			gpio-hog;
+			gpios = <13 0>;
+			output-high;
+			line-name = "MPCIE_RST#";
+		};
+	};
+};
+
+&irqsteer {
+	status = "okay";
+};
+
+&led2 {
+	gpios = <&gpio3 16 GPIO_ACTIVE_HIGH>;
+};
+
+&pcie0 {
+	reset-gpio = <&expander0 14 GPIO_ACTIVE_LOW>;
+	clocks = <&clk IMX8MQ_CLK_PCIE1_ROOT>,
+		 <&clk IMX8MQ_CLK_PCIE1_AUX>,
+		 <&clk IMX8MQ_CLK_PCIE1_PHY>,
+		 <&pcie0_refclk>;
+	clock-names = "pcie", "pcie_aux", "pcie_phy", "pcie_bus";
+	epdev_on-supply = <&reg_vcc_3v3>;
+	hard-wired = <1>;
+	status = "okay";
+};
+
+/*
+ * miniPCIe, also usable for cards with USB. Therefore configure the reset as
+ * static gpio hog.
+ */
+&pcie1 {
+	clocks = <&clk IMX8MQ_CLK_PCIE2_ROOT>,
+		 <&clk IMX8MQ_CLK_PCIE2_AUX>,
+		 <&clk IMX8MQ_CLK_PCIE2_PHY>,
+		 <&pcie1_refclk>;
+	clock-names = "pcie", "pcie_aux", "pcie_phy", "pcie_bus";
+	epdev_on-supply = <&reg_vcc_3v3>;
+	hard-wired = <1>;
+	status = "okay";
+};
+
+&sai3 {
+	assigned-clocks = <&clk IMX8MQ_CLK_SAI3>;
+	assigned-clock-parents = <&clk IMX8MQ_AUDIO_PLL1_OUT>;
+	clock-names = "bus", "mclk0", "mclk1", "mclk2", "mclk3", "pll8k", "pll11k";
+	clocks = <&clk IMX8MQ_CLK_SAI3_IPG>, <&clk IMX8MQ_CLK_DUMMY>,
+		<&clk IMX8MQ_CLK_SAI3_ROOT>, <&clk IMX8MQ_CLK_DUMMY>,
+		<&clk IMX8MQ_CLK_DUMMY>, <&clk IMX8MQ_AUDIO_PLL1_OUT>,
+		<&clk IMX8MQ_AUDIO_PLL2_OUT>;
+};
+
+&tlv320aic3x04 {
+	clock-names = "mclk";
+	clocks = <&clk IMX8MQ_CLK_SAI3_ROOT>;
+};
+
+&uart1 {
+	assigned-clocks = <&clk IMX8MQ_CLK_UART1>;
+	assigned-clock-parents = <&clk IMX8MQ_SYS1_PLL_80M>;
+};
+
+&uart2 {
+	assigned-clocks = <&clk IMX8MQ_CLK_UART2>;
+	assigned-clock-parents = <&clk IMX8MQ_SYS1_PLL_80M>;
+};
+
+/* console */
+&uart3 {
+	assigned-clocks = <&clk IMX8MQ_CLK_UART3>;
+	assigned-clock-parents = <&clk IMX8MQ_CLK_25M>;
+};
+
+&usb3_phy0 {
+	vbus-supply = <&reg_otg_vbus>;
+	status = "okay";
+};
+
+&usb_dwc3_0 {
+	/* we implement dual role but not full featured OTG */
+	extcon = <&extcon_usbotg>;
+	hnp-disable;
+	srp-disable;
+	adp-disable;
+	/* OC not supported due to non matching active polarity */
+	disable-over-current;
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&usb3_phy1 {
+	status = "okay";
+};
+
+&usb_dwc3_1 {
+	status = "okay";
+	dr_mode = "host";
+};
+
+&wdog1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_wdog>;
+	fsl,ext-reset-output;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_ecspi1: ecspi1grp {
+		fsl,pins = <MX8MQ_IOMUXC_ECSPI1_SCLK_ECSPI1_SCLK	0x0000004e>,
+			   <MX8MQ_IOMUXC_ECSPI1_MOSI_ECSPI1_MOSI	0x0000004e>,
+			   <MX8MQ_IOMUXC_ECSPI1_MISO_ECSPI1_MISO	0x0000004e>,
+			   <MX8MQ_IOMUXC_ECSPI1_SS0_GPIO5_IO9		0x0000004e>;
+	};
+
+	pinctrl_ecspi2: ecspi2grp {
+		fsl,pins = <MX8MQ_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK	0x0000004e>,
+			   <MX8MQ_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI	0x0000004e>,
+			   <MX8MQ_IOMUXC_ECSPI2_MISO_ECSPI2_MISO	0x0000004e>,
+			   <MX8MQ_IOMUXC_ECSPI2_SS0_GPIO5_IO13		0x0000004e>;
+	};
+
+	pinctrl_expander: expandergrp {
+		fsl,pins = <MX8MQ_IOMUXC_GPIO1_IO09_GPIO1_IO9		0xd6>;
+	};
+
+	pinctrl_fec1: fec1grp {
+		fsl,pins = <MX8MQ_IOMUXC_ENET_MDC_ENET1_MDC		0x3>,
+			   <MX8MQ_IOMUXC_ENET_MDIO_ENET1_MDIO		0x23>,
+			   <MX8MQ_IOMUXC_ENET_TD3_ENET1_RGMII_TD3	0x1f>,
+			   <MX8MQ_IOMUXC_ENET_TD2_ENET1_RGMII_TD2	0x1f>,
+			   <MX8MQ_IOMUXC_ENET_TD1_ENET1_RGMII_TD1	0x1f>,
+			   <MX8MQ_IOMUXC_ENET_TD0_ENET1_RGMII_TD0	0x1f>,
+			   <MX8MQ_IOMUXC_ENET_RD3_ENET1_RGMII_RD3	0x91>,
+			   <MX8MQ_IOMUXC_ENET_RD2_ENET1_RGMII_RD2	0x91>,
+			   <MX8MQ_IOMUXC_ENET_RD1_ENET1_RGMII_RD1	0x91>,
+			   <MX8MQ_IOMUXC_ENET_RD0_ENET1_RGMII_RD0	0x91>,
+			   <MX8MQ_IOMUXC_ENET_TXC_ENET1_RGMII_TXC	0x1f>,
+			   <MX8MQ_IOMUXC_ENET_RXC_ENET1_RGMII_RXC	0x91>,
+			   <MX8MQ_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL	0x91>,
+			   <MX8MQ_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL	0x1f>;
+	};
+
+	pinctrl_gpiobutton: gpiobuttongrp {
+		fsl,pins = <MX8MQ_IOMUXC_GPIO1_IO05_GPIO1_IO5		0x41>,
+			   <MX8MQ_IOMUXC_GPIO1_IO07_GPIO1_IO7		0x41>,
+			   <MX8MQ_IOMUXC_NAND_WE_B_GPIO3_IO17		0x41>;
+	};
+
+	pinctrl_gpioled: gpioledgrp {
+		fsl,pins = <MX8MQ_IOMUXC_GPIO1_IO00_GPIO1_IO0		0x41>,
+			   <MX8MQ_IOMUXC_GPIO1_IO08_GPIO1_IO8		0x41>,
+			   <MX8MQ_IOMUXC_NAND_READY_B_GPIO3_IO16	0x41>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <MX8MQ_IOMUXC_I2C2_SCL_I2C2_SCL		0x40000067>,
+			   <MX8MQ_IOMUXC_I2C2_SDA_I2C2_SDA		0x40000067>;
+	};
+
+	pinctrl_i2c2_gpio: i2c2gpiogrp {
+		fsl,pins = <MX8MQ_IOMUXC_I2C2_SCL_GPIO5_IO16		0x40000067>,
+			   <MX8MQ_IOMUXC_I2C2_SDA_GPIO5_IO17		0x40000067>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <MX8MQ_IOMUXC_I2C3_SCL_I2C3_SCL		0x40000067>,
+			   <MX8MQ_IOMUXC_I2C3_SDA_I2C3_SDA		0x40000067>;
+	};
+
+	pinctrl_i2c3_gpio: i2c3gpiogrp {
+		fsl,pins = <MX8MQ_IOMUXC_I2C3_SCL_GPIO5_IO18		0x40000067>,
+			   <MX8MQ_IOMUXC_I2C3_SDA_GPIO5_IO19		0x40000067>;
+	};
+
+	pinctrl_pwm3: pwm3grp {
+		fsl,pins = <MX8MQ_IOMUXC_GPIO1_IO14_PWM3_OUT		0x16>;
+	};
+
+	pinctrl_pwm4: pwm4grp {
+		fsl,pins = <MX8MQ_IOMUXC_GPIO1_IO15_PWM4_OUT		0x16>;
+	};
+
+	pinctrl_regotgvbus: reggotgvbusgrp {
+		/* USB1 OTG PWR as GPIO */
+		fsl,pins = <MX8MQ_IOMUXC_GPIO1_IO12_GPIO1_IO12		0x06>;
+	};
+
+	pinctrl_reg_usdhc2_vmmc: regusdhc2vmmcgrp {
+		fsl,pins = <MX8MQ_IOMUXC_SD2_RESET_B_GPIO2_IO19		0xc1>;
+	};
+
+	pinctrl_sai3: sai3grp {
+		fsl,pins = <MX8MQ_IOMUXC_SAI3_MCLK_SAI3_MCLK		0xd6>,
+			   <MX8MQ_IOMUXC_SAI3_RXC_SAI3_RX_BCLK		0xd6>,
+			   <MX8MQ_IOMUXC_SAI3_RXFS_SAI3_RX_SYNC		0xd6>,
+			   <MX8MQ_IOMUXC_SAI3_RXD_SAI3_RX_DATA0		0xd6>,
+			   <MX8MQ_IOMUXC_SAI3_TXFS_SAI3_TX_SYNC		0xd6>,
+			   <MX8MQ_IOMUXC_SAI3_TXD_SAI3_TX_DATA0		0xd6>,
+			   <MX8MQ_IOMUXC_SAI3_TXC_SAI3_TX_BCLK		0xd6>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <MX8MQ_IOMUXC_UART1_RXD_UART1_DCE_RX		0x79>,
+			   <MX8MQ_IOMUXC_UART1_TXD_UART1_DCE_TX		0x79>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <MX8MQ_IOMUXC_UART2_RXD_UART2_DCE_RX		0x79>,
+			   <MX8MQ_IOMUXC_UART2_TXD_UART2_DCE_TX		0x79>;
+	};
+
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <MX8MQ_IOMUXC_UART3_RXD_UART3_DCE_RX		0x79>,
+			   <MX8MQ_IOMUXC_UART3_TXD_UART3_DCE_TX		0x79>;
+	};
+
+	pinctrl_uart4: uart4grp {
+		fsl,pins = <MX8MQ_IOMUXC_UART4_RXD_UART4_DCE_RX		0x79>,
+			   <MX8MQ_IOMUXC_UART4_TXD_UART4_DCE_TX		0x79>;
+	};
+
+	pinctrl_usbcon0: usb0congrp {
+		/* ID: floating / high: device, low: host -> use PU */
+		fsl,pins = <MX8MQ_IOMUXC_GPIO1_IO10_GPIO1_IO10		0xe6>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK		0x83>,
+			   <MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD		0xc3>,
+			   <MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0		0xc3>,
+			   <MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1		0xc3>,
+			   <MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2		0xc3>,
+			   <MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3		0xc3>,
+			   <MX8MQ_IOMUXC_GPIO1_IO04_USDHC2_VSELECT	0xc1>;
+	};
+
+	pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+		fsl,pins = <MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK		0x85>,
+			   <MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD		0xc5>,
+			   <MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0		0xc5>,
+			   <MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1		0xc5>,
+			   <MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2		0xc5>,
+			   <MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3		0xc5>,
+			   <MX8MQ_IOMUXC_GPIO1_IO04_USDHC2_VSELECT	0xc1>;
+	};
+
+	pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+		fsl,pins = <MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK		0x9f>,
+			   <MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD		0xc7>,
+			   <MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0		0xc7>,
+			   <MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1		0xc7>,
+			   <MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2		0xc7>,
+			   <MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3		0xc7>,
+			   <MX8MQ_IOMUXC_GPIO1_IO04_USDHC2_VSELECT	0xc1>;
+	};
+
+	pinctrl_usdhc2_gpio: usdhc2-gpiogrp {
+		fsl,pins = <MX8MQ_IOMUXC_SD2_CD_B_GPIO2_IO12		0x41>;
+	};
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mq-tqma8mq.dtsi b/arch/arm64/boot/dts/freescale/imx8mq-tqma8mq.dtsi
new file mode 100644
index 000000000000..802ad6e5cef6
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mq-tqma8mq.dtsi
@@ -0,0 +1,355 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2019-2021 TQ-Systems GmbH
+ */
+
+#include "imx8mq.dtsi"
+
+/ {
+	model = "TQ-Systems GmbH i.MX8MQ TQMa8MQ";
+	compatible = "tq,imx8mq-tqma8mq", "fsl,imx8mq";
+
+	memory@40000000 {
+		device_type = "memory";
+		/*  our minimum RAM config will be 1024 MiB */
+		reg = <0x00000000 0x40000000 0 0x40000000>;
+	};
+
+	/* e-MMC IO, needed for HS modes */
+	reg_vcc1v8: regulator-vcc1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "TQMA8MX_VCC1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	reg_vcc3v3: regulator-vcc3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "TQMA8MX_VCC3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	reg_vdd_arm: regulator-vdd-arm {
+		compatible = "regulator-gpio";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_dvfs>;
+		regulator-min-microvolt = <900000>;
+		regulator-max-microvolt = <1000000>;
+		regulator-name = "TQMa8Mx_DVFS";
+		regulator-type = "voltage";
+		regulator-settling-time-us = <150000>;
+		gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
+		states = <900000 0x1 1000000 0x0>;
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		/* global autoconfigured region for contiguous allocations */
+		linux,cma {
+			compatible = "shared-dma-pool";
+			reusable;
+			/* 640 MiB */
+			size = <0 0x28000000>;
+			/*  1024 - 128 MiB, our minimum RAM config will be 1024 MiB */
+			alloc-ranges = <0 0x40000000 0 0x78000000>;
+			linux,cma-default;
+		};
+	};
+};
+
+&A53_0 {
+	cpu-supply = <&reg_vdd_arm>;
+};
+
+&A53_1 {
+	cpu-supply = <&reg_vdd_arm>;
+};
+
+&A53_2 {
+	cpu-supply = <&reg_vdd_arm>;
+};
+
+&A53_3 {
+	cpu-supply = <&reg_vdd_arm>;
+};
+
+&gpu {
+	status = "okay";
+};
+
+&pgc_gpu {
+	power-supply = <&sw1a_reg>;
+};
+
+&pgc_vpu {
+	power-supply = <&sw1c_reg>;
+};
+
+&i2c1 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	pinctrl-1 = <&pinctrl_i2c1_gpio>;
+	scl-gpios = <&gpio5 14 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio5 15 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "okay";
+
+	pfuze100: pmic@8 {
+		compatible = "fsl,pfuze100";
+		fsl,pfuze-support-disable-sw;
+		reg = <0x8>;
+
+		regulators {
+			/* VDD_GPU */
+			sw1a_reg: sw1ab {
+				regulator-min-microvolt = <825000>;
+				regulator-max-microvolt = <1100000>;
+			};
+
+			/* VDD_VPU */
+			sw1c_reg: sw1c {
+				regulator-min-microvolt = <825000>;
+				regulator-max-microvolt = <1100000>;
+			};
+
+			/* NVCC_DRAM */
+			sw2_reg: sw2 {
+				regulator-min-microvolt = <1100000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-always-on;
+			};
+
+			/* VDD_DRAM */
+			sw3a_reg: sw3ab {
+				regulator-min-microvolt = <825000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-always-on;
+			};
+
+			/* 1.8 V for QSPI NOR, e-MMC IO, must not be changed */
+			nvcc_1v8_reg: sw4 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+			};
+
+			swbst_reg: swbst {
+				regulator-min-microvolt = <5000000>;
+				regulator-max-microvolt = <5150000>;
+			};
+
+			snvs_reg: vsnvs {
+				regulator-min-microvolt = <1000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-always-on;
+			};
+
+			vref_reg: vrefddr {
+				regulator-always-on;
+			};
+
+			/* not used */
+			vgen1_reg: vgen1 {
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1550000>;
+			};
+
+			/* VDD_PHY_0V9 */
+			vgen2_reg: vgen2 {
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <975000>;
+				regulator-always-on;
+			};
+
+			/* VDD_PHY_1V8 */
+			vgen3_reg: vgen3 {
+				regulator-min-microvolt = <1675000>;
+				regulator-max-microvolt = <1975000>;
+				regulator-always-on;
+			};
+
+			/* VDDA_1V8 */
+			vgen4_reg: vgen4 {
+				regulator-min-microvolt = <1625000>;
+				regulator-max-microvolt = <1875000>;
+				regulator-always-on;
+			};
+
+			/* VDD_PHY_3V3 */
+			vgen5_reg: vgen5 {
+				regulator-min-microvolt = <3075000>;
+				regulator-max-microvolt = <3625000>;
+				regulator-always-on;
+			};
+
+			/* not used */
+			vgen6_reg: vgen6 {
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+			};
+		};
+	};
+
+	sensor0: temperature-sensor-eeprom@1b {
+		compatible = "nxp,se97", "jedec,jc-42.4-temp";
+		reg = <0x1b>;
+	};
+
+	pcf85063: rtc@51 {
+		compatible = "nxp,pcf85063a";
+		reg = <0x51>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_rtc>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <1 IRQ_TYPE_EDGE_FALLING>;
+		quartz-load-femtofarads = <7000>;
+
+		clock {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <32768>;
+		};
+	};
+
+	eeprom1: eeprom@53 {
+		compatible = "nxp,se97b", "atmel,24c02";
+		reg = <0x53>;
+		pagesize = <16>;
+		read-only;
+	};
+
+	eeprom0: eeprom@57 {
+		compatible = "atmel,24c64";
+		reg = <0x57>;
+		pagesize = <32>;
+	};
+};
+
+&pcie0 {
+	/* 3.3V supply, only way to switch on internal 1.8V supply using GPR */
+	vph-supply = <&vgen5_reg>;
+};
+
+&pcie1 {
+	/* 3.3V supply, only way to switch on internal 1.8V supply using GPR */
+	vph-supply = <&vgen5_reg>;
+};
+
+&qspi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_qspi>;
+	assigned-clocks = <&clk IMX8MQ_CLK_QSPI>;
+	assigned-clock-parents = <&clk IMX8MQ_SYS1_PLL_266M>;
+	status = "okay";
+
+	flash0: flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		spi-max-frequency = <84000000>;
+		spi-tx-bus-width = <1>;
+		spi-rx-bus-width = <4>;
+	};
+};
+
+&usdhc1 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
+	bus-width = <8>;
+	non-removable;
+	no-sd;
+	no-sdio;
+	vmmc-supply = <&reg_vcc3v3>;
+	vqmmc-supply = <&reg_vcc1v8>;
+	status = "okay";
+};
+
+/* Attention: wdog reset forcing POR needs baseboard support */
+&wdog1 {
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_dvfs: dvfsgrp {
+		fsl,pins = <MX8MQ_IOMUXC_GPIO1_IO06_GPIO1_IO6	0x16>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <MX8MQ_IOMUXC_I2C1_SCL_I2C1_SCL		0x4000007f>,
+			   <MX8MQ_IOMUXC_I2C1_SDA_I2C1_SDA		0x4000007f>;
+	};
+
+	pinctrl_i2c1_gpio: i2c1gpiogrp {
+		fsl,pins = <MX8MQ_IOMUXC_I2C1_SCL_GPIO5_IO14		0x40000074>,
+			   <MX8MQ_IOMUXC_I2C1_SDA_GPIO5_IO15		0x40000074>;
+	};
+
+	pinctrl_qspi: qspigrp {
+		fsl,pins = <MX8MQ_IOMUXC_NAND_ALE_QSPI_A_SCLK		0x97>,
+			   <MX8MQ_IOMUXC_NAND_CE0_B_QSPI_A_SS0_B	0x82>,
+			   <MX8MQ_IOMUXC_NAND_DATA00_QSPI_A_DATA0	0x97>,
+			   <MX8MQ_IOMUXC_NAND_DATA01_QSPI_A_DATA1	0x97>,
+			   <MX8MQ_IOMUXC_NAND_DATA02_QSPI_A_DATA2	0x97>,
+			   <MX8MQ_IOMUXC_NAND_DATA03_QSPI_A_DATA3	0x97>;
+	};
+
+	pinctrl_rtc: rtcgrp {
+		fsl,pins = <MX8MQ_IOMUXC_GPIO1_IO01_GPIO1_IO1		0x41>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK		0x83>,
+			   <MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD		0xc3>,
+			   <MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0		0xc3>,
+			   <MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1		0xc3>,
+			   <MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2		0xc3>,
+			   <MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3		0xc3>,
+			   <MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4		0xc3>,
+			   <MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5		0xc3>,
+			   <MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6		0xc3>,
+			   <MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7		0xc3>,
+			   <MX8MQ_IOMUXC_SD1_STROBE_USDHC1_STROBE	0x83>,
+			   <MX8MQ_IOMUXC_SD1_RESET_B_USDHC1_RESET_B	0xc1>;
+	};
+
+	pinctrl_usdhc1_100mhz: usdhc1-100mhzgrp {
+		fsl,pins = <MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK		0x85>,
+			   <MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD		0xc5>,
+			   <MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0		0xc5>,
+			   <MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1		0xc5>,
+			   <MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2		0xc5>,
+			   <MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3		0xc5>,
+			   <MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4		0xc5>,
+			   <MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5		0xc5>,
+			   <MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6		0xc5>,
+			   <MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7		0xc5>,
+			   <MX8MQ_IOMUXC_SD1_STROBE_USDHC1_STROBE	0x85>,
+			   <MX8MQ_IOMUXC_SD1_RESET_B_USDHC1_RESET_B	0xc1>;
+	};
+
+	pinctrl_usdhc1_200mhz: usdhc1-200mhzgrp {
+		fsl,pins = <MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK		0x87>,
+			   <MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD		0xc7>,
+			   <MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0		0xc7>,
+			   <MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1		0xc7>,
+			   <MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2		0xc7>,
+			   <MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3		0xc7>,
+			   <MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4		0xc7>,
+			   <MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5		0xc7>,
+			   <MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6		0xc7>,
+			   <MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7		0xc7>,
+			   <MX8MQ_IOMUXC_SD1_STROBE_USDHC1_STROBE	0x87>,
+			   <MX8MQ_IOMUXC_SD1_RESET_B_USDHC1_RESET_B	0xc1>;
+	};
+
+	pinctrl_wdog: wdoggrp {
+		fsl,pins = <MX8MQ_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B	0xc6>;
+	};
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mq-zii-ultra.dtsi b/arch/arm64/boot/dts/freescale/imx8mq-zii-ultra.dtsi
index 2222ef7b3eab..4e05120c62d4 100644
--- a/arch/arm64/boot/dts/freescale/imx8mq-zii-ultra.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mq-zii-ultra.dtsi
@@ -443,7 +443,7 @@
 	status = "okay";
 
 	usbhub: usbhub@2c {
-		compatible ="microchip,usb2513b";
+		compatible = "microchip,usb2513b";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_usbhub>;
 		reg = <0x2c>;
diff --git a/arch/arm64/boot/dts/freescale/imx8mq.dtsi b/arch/arm64/boot/dts/freescale/imx8mq.dtsi
index 972766b67a15..19eaa523564d 100644
--- a/arch/arm64/boot/dts/freescale/imx8mq.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mq.dtsi
@@ -63,6 +63,13 @@
 		clock-output-names = "osc_27m";
 	};
 
+	hdmi_phy_27m: clock-hdmi-phy-27m {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <27000000>;
+		clock-output-names = "hdmi_phy_27m";
+	};
+
 	clk_ext1: clock-ext1 {
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
@@ -87,7 +94,7 @@
 	clk_ext4: clock-ext4 {
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
-		clock-frequency= <133000000>;
+		clock-frequency = <133000000>;
 		clock-output-names = "clk_ext4";
 	};
 
@@ -102,6 +109,12 @@
 			clock-latency = <61036>; /* two CLK32 periods */
 			clocks = <&clk IMX8MQ_CLK_ARM>;
 			enable-method = "psci";
+			i-cache-size = <0x8000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <128>;
 			next-level-cache = <&A53_L2>;
 			operating-points-v2 = <&a53_opp_table>;
 			#cooling-cells = <2>;
@@ -116,6 +129,12 @@
 			clock-latency = <61036>; /* two CLK32 periods */
 			clocks = <&clk IMX8MQ_CLK_ARM>;
 			enable-method = "psci";
+			i-cache-size = <0x8000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <128>;
 			next-level-cache = <&A53_L2>;
 			operating-points-v2 = <&a53_opp_table>;
 			#cooling-cells = <2>;
@@ -128,6 +147,12 @@
 			clock-latency = <61036>; /* two CLK32 periods */
 			clocks = <&clk IMX8MQ_CLK_ARM>;
 			enable-method = "psci";
+			i-cache-size = <0x8000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <128>;
 			next-level-cache = <&A53_L2>;
 			operating-points-v2 = <&a53_opp_table>;
 			#cooling-cells = <2>;
@@ -140,6 +165,12 @@
 			clock-latency = <61036>; /* two CLK32 periods */
 			clocks = <&clk IMX8MQ_CLK_ARM>;
 			enable-method = "psci";
+			i-cache-size = <0x8000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <128>;
 			next-level-cache = <&A53_L2>;
 			operating-points-v2 = <&a53_opp_table>;
 			#cooling-cells = <2>;
@@ -147,6 +178,10 @@
 
 		A53_L2: l2-cache0 {
 			compatible = "cache";
+			cache-level = <2>;
+			cache-size = <0x100000>;
+			cache-line-size = <64>;
+			cache-sets = <1024>;
 		};
 	};
 
@@ -285,7 +320,7 @@
 		arm,no-tick-in-suspend;
 	};
 
-	soc@0 {
+	soc: soc@0 {
 		compatible = "fsl,imx8mq-soc", "simple-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -294,7 +329,7 @@
 		nvmem-cells = <&imx8mq_uid>;
 		nvmem-cell-names = "soc_unique_id";
 
-		bus@30000000 { /* AIPS1 */
+		aips1: bus@30000000 { /* AIPS1 */
 			compatible = "fsl,aips-bus", "simple-bus";
 			reg = <0x30000000 0x400000>;
 			#address-cells = <1>;
@@ -429,50 +464,50 @@
 				clocks = <&clk IMX8MQ_CLK_TMU_ROOT>;
 				little-endian;
 				fsl,tmu-range = <0xb0000 0xa0026 0x80048 0x70061>;
-				fsl,tmu-calibration = <0x00000000 0x00000023
-						       0x00000001 0x00000029
-						       0x00000002 0x0000002f
-						       0x00000003 0x00000035
-						       0x00000004 0x0000003d
-						       0x00000005 0x00000043
-						       0x00000006 0x0000004b
-						       0x00000007 0x00000051
-						       0x00000008 0x00000057
-						       0x00000009 0x0000005f
-						       0x0000000a 0x00000067
-						       0x0000000b 0x0000006f
-
-						       0x00010000 0x0000001b
-						       0x00010001 0x00000023
-						       0x00010002 0x0000002b
-						       0x00010003 0x00000033
-						       0x00010004 0x0000003b
-						       0x00010005 0x00000043
-						       0x00010006 0x0000004b
-						       0x00010007 0x00000055
-						       0x00010008 0x0000005d
-						       0x00010009 0x00000067
-						       0x0001000a 0x00000070
-
-						       0x00020000 0x00000017
-						       0x00020001 0x00000023
-						       0x00020002 0x0000002d
-						       0x00020003 0x00000037
-						       0x00020004 0x00000041
-						       0x00020005 0x0000004b
-						       0x00020006 0x00000057
-						       0x00020007 0x00000063
-						       0x00020008 0x0000006f
-
-						       0x00030000 0x00000015
-						       0x00030001 0x00000021
-						       0x00030002 0x0000002d
-						       0x00030003 0x00000039
-						       0x00030004 0x00000045
-						       0x00030005 0x00000053
-						       0x00030006 0x0000005f
-						       0x00030007 0x00000071>;
-				#thermal-sensor-cells =  <1>;
+				fsl,tmu-calibration = <0x00000000 0x00000023>,
+						      <0x00000001 0x00000029>,
+						      <0x00000002 0x0000002f>,
+						      <0x00000003 0x00000035>,
+						      <0x00000004 0x0000003d>,
+						      <0x00000005 0x00000043>,
+						      <0x00000006 0x0000004b>,
+						      <0x00000007 0x00000051>,
+						      <0x00000008 0x00000057>,
+						      <0x00000009 0x0000005f>,
+						      <0x0000000a 0x00000067>,
+						      <0x0000000b 0x0000006f>,
+
+						      <0x00010000 0x0000001b>,
+						      <0x00010001 0x00000023>,
+						      <0x00010002 0x0000002b>,
+						      <0x00010003 0x00000033>,
+						      <0x00010004 0x0000003b>,
+						      <0x00010005 0x00000043>,
+						      <0x00010006 0x0000004b>,
+						      <0x00010007 0x00000055>,
+						      <0x00010008 0x0000005d>,
+						      <0x00010009 0x00000067>,
+						      <0x0001000a 0x00000070>,
+
+						      <0x00020000 0x00000017>,
+						      <0x00020001 0x00000023>,
+						      <0x00020002 0x0000002d>,
+						      <0x00020003 0x00000037>,
+						      <0x00020004 0x00000041>,
+						      <0x00020005 0x0000004b>,
+						      <0x00020006 0x00000057>,
+						      <0x00020007 0x00000063>,
+						      <0x00020008 0x0000006f>,
+
+						      <0x00030000 0x00000015>,
+						      <0x00030001 0x00000021>,
+						      <0x00030002 0x0000002d>,
+						      <0x00030003 0x00000039>,
+						      <0x00030004 0x00000045>,
+						      <0x00030005 0x00000053>,
+						      <0x00030006 0x0000005f>,
+						      <0x00030007 0x00000071>;
+				#thermal-sensor-cells = <1>;
 			};
 
 			wdog1: watchdog@30280000 {
@@ -499,7 +534,7 @@
 				status = "disabled";
 			};
 
-			sdma2: sdma@302c0000 {
+			sdma2: dma-controller@302c0000 {
 				compatible = "fsl,imx8mq-sdma","fsl,imx7d-sdma";
 				reg = <0x302c0000 0x10000>;
 				interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
@@ -524,11 +559,9 @@
 						  <&clk IMX8MQ_VIDEO_PLL1>,
 						  <&clk IMX8MQ_VIDEO_PLL1_OUT>;
 				assigned-clock-rates = <0>, <0>, <0>, <594000000>;
-				interconnects = <&noc IMX8MQ_ICM_LCDIF &noc IMX8MQ_ICS_DRAM>;
-				interconnect-names = "dram";
 				status = "disabled";
 
-				port@0 {
+				port {
 					lcdif_mipi_dsi: endpoint {
 						remote-endpoint = <&mipi_dsi_lcdif_in>;
 					};
@@ -711,7 +744,21 @@
 					pgc_vpu: power-domain@6 {
 						#power-domain-cells = <0>;
 						reg = <IMX8M_POWER_DOMAIN_VPU>;
-						clocks = <&clk IMX8MQ_CLK_VPU_DEC_ROOT>;
+						clocks = <&clk IMX8MQ_CLK_VPU_DEC_ROOT>,
+							 <&clk IMX8MQ_CLK_VPU_G1_ROOT>,
+							 <&clk IMX8MQ_CLK_VPU_G2_ROOT>;
+						assigned-clocks = <&clk IMX8MQ_CLK_VPU_G1>,
+								  <&clk IMX8MQ_CLK_VPU_G2>,
+								  <&clk IMX8MQ_CLK_VPU_BUS>,
+								  <&clk IMX8MQ_VPU_PLL_BYPASS>;
+						assigned-clock-parents = <&clk IMX8MQ_VPU_PLL_OUT>,
+									 <&clk IMX8MQ_VPU_PLL_OUT>,
+									 <&clk IMX8MQ_SYS1_PLL_800M>,
+									 <&clk IMX8MQ_VPU_PLL>;
+						assigned-clock-rates = <600000000>,
+								       <600000000>,
+								       <800000000>,
+								       <0>;
 					};
 
 					pgc_disp: power-domain@7 {
@@ -737,7 +784,7 @@
 			};
 		};
 
-		bus@30400000 { /* AIPS2 */
+		aips2: bus@30400000 { /* AIPS2 */
 			compatible = "fsl,aips-bus", "simple-bus";
 			reg = <0x30400000 0x400000>;
 			#address-cells = <1>;
@@ -751,7 +798,7 @@
 				clocks = <&clk IMX8MQ_CLK_PWM1_ROOT>,
 				         <&clk IMX8MQ_CLK_PWM1_ROOT>;
 				clock-names = "ipg", "per";
-				#pwm-cells = <2>;
+				#pwm-cells = <3>;
 				status = "disabled";
 			};
 
@@ -762,7 +809,7 @@
 				clocks = <&clk IMX8MQ_CLK_PWM2_ROOT>,
 				         <&clk IMX8MQ_CLK_PWM2_ROOT>;
 				clock-names = "ipg", "per";
-				#pwm-cells = <2>;
+				#pwm-cells = <3>;
 				status = "disabled";
 			};
 
@@ -773,7 +820,7 @@
 				clocks = <&clk IMX8MQ_CLK_PWM3_ROOT>,
 				         <&clk IMX8MQ_CLK_PWM3_ROOT>;
 				clock-names = "ipg", "per";
-				#pwm-cells = <2>;
+				#pwm-cells = <3>;
 				status = "disabled";
 			};
 
@@ -784,7 +831,7 @@
 				clocks = <&clk IMX8MQ_CLK_PWM4_ROOT>,
 				         <&clk IMX8MQ_CLK_PWM4_ROOT>;
 				clock-names = "ipg", "per";
-				#pwm-cells = <2>;
+				#pwm-cells = <3>;
 				status = "disabled";
 			};
 
@@ -797,7 +844,7 @@
 			};
 		};
 
-		bus@30800000 { /* AIPS3 */
+		aips3: bus@30800000 { /* AIPS3 */
 			compatible = "fsl,aips-bus", "simple-bus";
 			reg = <0x30800000 0x400000>;
 			#address-cells = <1>;
@@ -971,6 +1018,7 @@
 					compatible = "fsl,sec-v4.0-job-ring";
 					reg = <0x1000 0x1000>;
 					interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>;
+					status = "disabled";
 				};
 
 				sec_jr1: jr@2000 {
@@ -1125,8 +1173,8 @@
 					#address-cells = <1>;
 					#size-cells = <0>;
 
-					port@0 {
-						reg = <0>;
+					port@1 {
+						reg = <1>;
 
 						csi1_mipi_ep: endpoint {
 							remote-endpoint = <&csi1_ep>;
@@ -1177,8 +1225,8 @@
 					#address-cells = <1>;
 					#size-cells = <0>;
 
-					port@0 {
-						reg = <0>;
+					port@1 {
+						reg = <1>;
 
 						csi2_mipi_ep: endpoint {
 							remote-endpoint = <&csi2_ep>;
@@ -1254,7 +1302,7 @@
 				status = "disabled";
 			};
 
-			sdma1: sdma@30bd0000 {
+			sdma1: dma-controller@30bd0000 {
 				compatible = "fsl,imx8mq-sdma","fsl,imx7d-sdma";
 				reg = <0x30bd0000 0x10000>;
 				interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
@@ -1292,7 +1340,6 @@
 				fsl,num-rx-queues = <3>;
 				nvmem-cells = <&fec_mac_address>;
 				nvmem-cell-names = "mac-address";
-				nvmem_macaddr_swap;
 				fsl,stop-mode = <&iomuxc_gpr 0x10 3>;
 				status = "disabled";
 			};
@@ -1323,7 +1370,7 @@
 			};
 		};
 
-		bus@32c00000 { /* AIPS4 */
+		aips4: bus@32c00000 { /* AIPS4 */
 			compatible = "fsl,aips-bus", "simple-bus";
 			reg = <0x32c00000 0x400000>;
 			#address-cells = <1>;
@@ -1432,30 +1479,31 @@
 			status = "disabled";
 		};
 
-		vpu: video-codec@38300000 {
-			compatible = "nxp,imx8mq-vpu";
-			reg = <0x38300000 0x10000>,
-			      <0x38310000 0x10000>,
-			      <0x38320000 0x10000>;
-			reg-names = "g1", "g2", "ctrl";
-			interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,
-				     <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "g1", "g2";
+		vpu_g1: video-codec@38300000 {
+			compatible = "nxp,imx8mq-vpu-g1";
+			reg = <0x38300000 0x10000>;
+			interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk IMX8MQ_CLK_VPU_G1_ROOT>;
+			power-domains = <&vpu_blk_ctrl IMX8MQ_VPUBLK_PD_G1>;
+		};
+
+		vpu_g2: video-codec@38310000 {
+			compatible = "nxp,imx8mq-vpu-g2";
+			reg = <0x38310000 0x10000>;
+			interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk IMX8MQ_CLK_VPU_G2_ROOT>;
+			power-domains = <&vpu_blk_ctrl IMX8MQ_VPUBLK_PD_G2>;
+		};
+
+		vpu_blk_ctrl: blk-ctrl@38320000 {
+			compatible = "fsl,imx8mq-vpu-blk-ctrl";
+			reg = <0x38320000 0x100>;
+			power-domains = <&pgc_vpu>, <&pgc_vpu>, <&pgc_vpu>;
+			power-domain-names = "bus", "g1", "g2";
 			clocks = <&clk IMX8MQ_CLK_VPU_G1_ROOT>,
-				 <&clk IMX8MQ_CLK_VPU_G2_ROOT>,
-				 <&clk IMX8MQ_CLK_VPU_DEC_ROOT>;
-			clock-names = "g1", "g2", "bus";
-			assigned-clocks = <&clk IMX8MQ_CLK_VPU_G1>,
-					  <&clk IMX8MQ_CLK_VPU_G2>,
-					  <&clk IMX8MQ_CLK_VPU_BUS>,
-					  <&clk IMX8MQ_VPU_PLL_BYPASS>;
-			assigned-clock-parents = <&clk IMX8MQ_VPU_PLL_OUT>,
-						 <&clk IMX8MQ_VPU_PLL_OUT>,
-						 <&clk IMX8MQ_SYS1_PLL_800M>,
-						 <&clk IMX8MQ_VPU_PLL>;
-			assigned-clock-rates = <600000000>, <600000000>,
-					       <800000000>, <0>;
-			power-domains = <&pgc_vpu>;
+				 <&clk IMX8MQ_CLK_VPU_G2_ROOT>;
+			clock-names = "g1", "g2";
+			#power-domain-cells = <1>;
 		};
 
 		pcie0: pcie@33800000 {
@@ -1554,6 +1602,7 @@
 				 <&clk IMX8MQ_DRAM_PLL_OUT>,
 				 <&clk IMX8MQ_CLK_DRAM_ALT>,
 				 <&clk IMX8MQ_CLK_DRAM_APB>;
+			status = "disabled";
 		};
 
 		ddr-pmu@3d800000 {
diff --git a/arch/arm64/boot/dts/freescale/imx8qm-ss-conn.dtsi b/arch/arm64/boot/dts/freescale/imx8qm-ss-conn.dtsi
index 42637a45701c..ec1639174e2e 100644
--- a/arch/arm64/boot/dts/freescale/imx8qm-ss-conn.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8qm-ss-conn.dtsi
@@ -19,3 +19,7 @@
 &usdhc2 {
 	compatible = "fsl,imx8qm-usdhc", "fsl,imx8qxp-usdhc", "fsl,imx7d-usdhc";
 };
+
+&usdhc3 {
+	compatible = "fsl,imx8qm-usdhc", "fsl,imx8qxp-usdhc", "fsl,imx7d-usdhc";
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8qm-ss-lsio.dtsi b/arch/arm64/boot/dts/freescale/imx8qm-ss-lsio.dtsi
index 30896610c654..669aa14ce9f7 100644
--- a/arch/arm64/boot/dts/freescale/imx8qm-ss-lsio.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8qm-ss-lsio.dtsi
@@ -56,6 +56,14 @@
 	compatible = "fsl,imx8-mu-scu", "fsl,imx8qm-mu", "fsl,imx6sx-mu";
 };
 
+&lsio_mu5 {
+	compatible = "fsl,imx8qm-mu", "fsl,imx6sx-mu";
+};
+
+&lsio_mu6 {
+	compatible = "fsl,imx8qm-mu", "fsl,imx6sx-mu";
+};
+
 &lsio_mu13 {
 	compatible = "fsl,imx8qm-mu", "fsl,imx6sx-mu";
 };
diff --git a/arch/arm64/boot/dts/freescale/imx8qm.dtsi b/arch/arm64/boot/dts/freescale/imx8qm.dtsi
index aebbe2b84aa1..c9c2b6536233 100644
--- a/arch/arm64/boot/dts/freescale/imx8qm.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8qm.dtsi
@@ -20,6 +20,9 @@
 		mmc1 = &usdhc2;
 		mmc2 = &usdhc3;
 		serial0 = &lpuart0;
+		serial1 = &lpuart1;
+		serial2 = &lpuart2;
+		serial3 = &lpuart3;
 	};
 
 	cpus {
@@ -54,47 +57,77 @@
 
 		A53_0: cpu@0 {
 			device_type = "cpu";
-			compatible = "arm,cortex-a53", "arm,armv8";
+			compatible = "arm,cortex-a53";
 			reg = <0x0 0x0>;
 			enable-method = "psci";
+			i-cache-size = <0x8000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <128>;
 			next-level-cache = <&A53_L2>;
 		};
 
 		A53_1: cpu@1 {
 			device_type = "cpu";
-			compatible = "arm,cortex-a53", "arm,armv8";
+			compatible = "arm,cortex-a53";
 			reg = <0x0 0x1>;
 			enable-method = "psci";
+			i-cache-size = <0x8000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <128>;
 			next-level-cache = <&A53_L2>;
 		};
 
 		A53_2: cpu@2 {
 			device_type = "cpu";
-			compatible = "arm,cortex-a53", "arm,armv8";
+			compatible = "arm,cortex-a53";
 			reg = <0x0 0x2>;
 			enable-method = "psci";
+			i-cache-size = <0x8000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <128>;
 			next-level-cache = <&A53_L2>;
 		};
 
 		A53_3: cpu@3 {
 			device_type = "cpu";
-			compatible = "arm,cortex-a53", "arm,armv8";
+			compatible = "arm,cortex-a53";
 			reg = <0x0 0x3>;
 			enable-method = "psci";
+			i-cache-size = <0x8000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <128>;
 			next-level-cache = <&A53_L2>;
 		};
 
 		A72_0: cpu@100 {
 			device_type = "cpu";
-			compatible = "arm,cortex-a72", "arm,armv8";
+			compatible = "arm,cortex-a72";
 			reg = <0x0 0x100>;
 			enable-method = "psci";
+			i-cache-size = <0xC000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <256>;
 			next-level-cache = <&A72_L2>;
 		};
 
 		A72_1: cpu@101 {
 			device_type = "cpu";
-			compatible = "arm,cortex-a72", "arm,armv8";
+			compatible = "arm,cortex-a72";
 			reg = <0x0 0x101>;
 			enable-method = "psci";
 			next-level-cache = <&A72_L2>;
@@ -102,10 +135,18 @@
 
 		A53_L2: l2-cache0 {
 			compatible = "cache";
+			cache-level = <2>;
+			cache-size = <0x100000>;
+			cache-line-size = <64>;
+			cache-sets = <1024>;
 		};
 
 		A72_L2: l2-cache1 {
 			compatible = "cache";
+			cache-level = <2>;
+			cache-size = <0x100000>;
+			cache-line-size = <64>;
+			cache-sets = <1024>;
 		};
 	};
 
@@ -140,7 +181,7 @@
 			     <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW>; /* Hypervisor */
 	};
 
-	scu {
+	system-controller {
 		compatible = "fsl,imx-scu";
 		mbox-names = "tx0",
 			     "rx0",
@@ -149,13 +190,13 @@
 			  &lsio_mu1 1 0
 			  &lsio_mu1 3 3>;
 
-		pd: imx8qx-pd {
+		pd: power-controller {
 			compatible = "fsl,imx8qm-scu-pd", "fsl,scu-pd";
 			#power-domain-cells = <1>;
 		};
 
 		clk: clock-controller {
-			compatible = "fsl,imx8qxp-clk", "fsl,scu-clk";
+			compatible = "fsl,imx8qm-clk", "fsl,scu-clk";
 			#clock-cells = <2>;
 		};
 
@@ -163,6 +204,9 @@
 			compatible = "fsl,imx8qm-iomuxc";
 		};
 
+		rtc: rtc {
+			compatible = "fsl,imx8qxp-sc-rtc";
+		};
 	};
 
 	/* sorted in register address */
diff --git a/arch/arm64/boot/dts/freescale/imx8qxp-colibri-eval-v3.dtsi b/arch/arm64/boot/dts/freescale/imx8qxp-colibri-eval-v3.dtsi
index 144fc9e82da7..a08e70fb7c7a 100644
--- a/arch/arm64/boot/dts/freescale/imx8qxp-colibri-eval-v3.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8qxp-colibri-eval-v3.dtsi
@@ -16,7 +16,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_gpiokeys>;
 
-		wakeup {
+		key-wakeup {
 			label = "Wake-Up";
 			gpios = <&lsio_gpio3 10 GPIO_ACTIVE_HIGH>;
 			linux,code = <KEY_WAKEUP>;
@@ -38,17 +38,17 @@
 
 /* Colibri UART_B */
 &lpuart0 {
-	status= "okay";
+	status = "okay";
 };
 
 /* Colibri UART_C */
 &lpuart2 {
-	status= "okay";
+	status = "okay";
 };
 
 /* Colibri UART_A */
 &lpuart3 {
-	status= "okay";
+	status = "okay";
 };
 
 /* Colibri FastEthernet */
diff --git a/arch/arm64/boot/dts/freescale/imx8qxp-mek.dts b/arch/arm64/boot/dts/freescale/imx8qxp-mek.dts
index 863232a47004..07d8dd8160f6 100644
--- a/arch/arm64/boot/dts/freescale/imx8qxp-mek.dts
+++ b/arch/arm64/boot/dts/freescale/imx8qxp-mek.dts
@@ -135,6 +135,14 @@
 	status = "okay";
 };
 
+&mu_m0 {
+	status = "okay";
+};
+
+&mu1_m0 {
+	status = "okay";
+};
+
 &scu_key {
 	status = "okay";
 };
@@ -196,6 +204,23 @@
 	status = "okay";
 };
 
+&vpu {
+	compatible = "nxp,imx8qxp-vpu";
+	status = "okay";
+};
+
+&vpu_core0 {
+	reg = <0x2d040000 0x10000>;
+	memory-region = <&decoder_boot>, <&decoder_rpc>;
+	status = "okay";
+};
+
+&vpu_core1 {
+	reg = <0x2d050000 0x10000>;
+	memory-region = <&encoder_boot>, <&encoder_rpc>;
+	status = "okay";
+};
+
 &iomuxc {
 	pinctrl_fec1: fec1grp {
 		fsl,pins = <
diff --git a/arch/arm64/boot/dts/freescale/imx8qxp-ss-adma.dtsi b/arch/arm64/boot/dts/freescale/imx8qxp-ss-adma.dtsi
index dc1daa8dc72f..7bae516004bf 100644
--- a/arch/arm64/boot/dts/freescale/imx8qxp-ss-adma.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8qxp-ss-adma.dtsi
@@ -5,19 +5,19 @@
  */
 
 &lpuart0 {
-	compatible = "fsl,imx8qxp-lpuart", "fsl,imx7ulp-lpuart";
+	compatible = "fsl,imx8qxp-lpuart";
 };
 
 &lpuart1 {
-	compatible = "fsl,imx8qxp-lpuart", "fsl,imx7ulp-lpuart";
+	compatible = "fsl,imx8qxp-lpuart";
 };
 
 &lpuart2 {
-	compatible = "fsl,imx8qxp-lpuart", "fsl,imx7ulp-lpuart";
+	compatible = "fsl,imx8qxp-lpuart";
 };
 
 &lpuart3 {
-	compatible = "fsl,imx8qxp-lpuart", "fsl,imx7ulp-lpuart";
+	compatible = "fsl,imx8qxp-lpuart";
 };
 
 &i2c0 {
diff --git a/arch/arm64/boot/dts/freescale/imx8qxp-ss-lsio.dtsi b/arch/arm64/boot/dts/freescale/imx8qxp-ss-lsio.dtsi
index 11395479ffc0..8e2152c6eb88 100644
--- a/arch/arm64/boot/dts/freescale/imx8qxp-ss-lsio.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8qxp-ss-lsio.dtsi
@@ -56,6 +56,14 @@
 	compatible = "fsl,imx8-mu-scu", "fsl,imx8qxp-mu", "fsl,imx6sx-mu";
 };
 
+&lsio_mu5 {
+	compatible = "fsl,imx8qxp-mu", "fsl,imx6sx-mu";
+};
+
+&lsio_mu6 {
+	compatible = "fsl,imx8qxp-mu", "fsl,imx6sx-mu";
+};
+
 &lsio_mu13 {
 	compatible = "fsl,imx8qxp-mu", "fsl,imx6sx-mu";
 };
diff --git a/arch/arm64/boot/dts/freescale/imx8qxp.dtsi b/arch/arm64/boot/dts/freescale/imx8qxp.dtsi
index 617618edf77e..f4ea18bb95ab 100644
--- a/arch/arm64/boot/dts/freescale/imx8qxp.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8qxp.dtsi
@@ -46,6 +46,9 @@
 		serial1 = &lpuart1;
 		serial2 = &lpuart2;
 		serial3 = &lpuart3;
+		vpu_core0 = &vpu_core0;
+		vpu_core1 = &vpu_core1;
+		vpu_core2 = &vpu_core2;
 	};
 
 	cpus {
@@ -58,6 +61,12 @@
 			compatible = "arm,cortex-a35";
 			reg = <0x0 0x0>;
 			enable-method = "psci";
+			i-cache-size = <0x8000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <128>;
 			next-level-cache = <&A35_L2>;
 			clocks = <&clk IMX_SC_R_A35 IMX_SC_PM_CLK_CPU>;
 			operating-points-v2 = <&a35_opp_table>;
@@ -69,6 +78,12 @@
 			compatible = "arm,cortex-a35";
 			reg = <0x0 0x1>;
 			enable-method = "psci";
+			i-cache-size = <0x8000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <128>;
 			next-level-cache = <&A35_L2>;
 			clocks = <&clk IMX_SC_R_A35 IMX_SC_PM_CLK_CPU>;
 			operating-points-v2 = <&a35_opp_table>;
@@ -80,6 +95,12 @@
 			compatible = "arm,cortex-a35";
 			reg = <0x0 0x2>;
 			enable-method = "psci";
+			i-cache-size = <0x8000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <128>;
 			next-level-cache = <&A35_L2>;
 			clocks = <&clk IMX_SC_R_A35 IMX_SC_PM_CLK_CPU>;
 			operating-points-v2 = <&a35_opp_table>;
@@ -91,6 +112,12 @@
 			compatible = "arm,cortex-a35";
 			reg = <0x0 0x3>;
 			enable-method = "psci";
+			i-cache-size = <0x8000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <128>;
 			next-level-cache = <&A35_L2>;
 			clocks = <&clk IMX_SC_R_A35 IMX_SC_PM_CLK_CPU>;
 			operating-points-v2 = <&a35_opp_table>;
@@ -99,6 +126,10 @@
 
 		A35_L2: l2-cache0 {
 			compatible = "cache";
+			cache-level = <2>;
+			cache-size = <0x80000>;
+			cache-line-size = <64>;
+			cache-sets = <1024>;
 		};
 	};
 
@@ -134,10 +165,30 @@
 		#size-cells = <2>;
 		ranges;
 
+		decoder_boot: decoder-boot@84000000 {
+			reg = <0 0x84000000 0 0x2000000>;
+			no-map;
+		};
+
+		encoder_boot: encoder-boot@86000000 {
+			reg = <0 0x86000000 0 0x200000>;
+			no-map;
+		};
+
+		decoder_rpc: decoder-rpc@92000000 {
+			reg = <0 0x92000000 0 0x100000>;
+			no-map;
+		};
+
 		dsp_reserved: dsp@92400000 {
 			reg = <0 0x92400000 0 0x2000000>;
 			no-map;
 		};
+
+		encoder_rpc: encoder-rpc@94400000 {
+			reg = <0 0x94400000 0 0x700000>;
+			no-map;
+		};
 	};
 
 	pmu {
@@ -150,7 +201,7 @@
 		method = "smc";
 	};
 
-	scu {
+	system-controller {
 		compatible = "fsl,imx-scu";
 		mbox-names = "tx0",
 			     "rx0",
@@ -159,29 +210,27 @@
 			  &lsio_mu1 1 0
 			  &lsio_mu1 3 3>;
 
-		pd: imx8qx-pd {
+		pd: power-controller {
 			compatible = "fsl,imx8qxp-scu-pd", "fsl,scu-pd";
 			#power-domain-cells = <1>;
 		};
 
 		clk: clock-controller {
-			compatible = "fsl,imx8qxp-clk";
+			compatible = "fsl,imx8qxp-clk", "fsl,scu-clk";
 			#clock-cells = <2>;
-			clocks = <&xtal32k &xtal24m>;
-			clock-names = "xtal_32KHz", "xtal_24Mhz";
 		};
 
 		iomuxc: pinctrl {
 			compatible = "fsl,imx8qxp-iomuxc";
 		};
 
-		ocotp: imx8qx-ocotp {
+		ocotp: ocotp {
 			compatible = "fsl,imx8qxp-scu-ocotp";
 			#address-cells = <1>;
 			#size-cells = <1>;
 		};
 
-		scu_key: scu-key {
+		scu_key: keys {
 			compatible = "fsl,imx8qxp-sc-key", "fsl,imx-sc-key";
 			linux,keycodes = <KEY_POWER>;
 			status = "disabled";
@@ -225,7 +274,7 @@
 	};
 
 	thermal_zones: thermal-zones {
-		cpu-thermal0 {
+		cpu0-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <2000>;
 			thermal-sensors = <&tsens IMX_SC_R_SYSTEM>;
@@ -259,6 +308,7 @@
 
 	/* sorted in register address */
 	#include "imx8-ss-img.dtsi"
+	#include "imx8-ss-vpu.dtsi"
 	#include "imx8-ss-adma.dtsi"
 	#include "imx8-ss-conn.dtsi"
 	#include "imx8-ss-ddr.dtsi"
diff --git a/arch/arm64/boot/dts/freescale/imx8ulp-evk.dts b/arch/arm64/boot/dts/freescale/imx8ulp-evk.dts
new file mode 100644
index 000000000000..f1c6d933a17c
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8ulp-evk.dts
@@ -0,0 +1,121 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2021 NXP
+ */
+
+/dts-v1/;
+
+#include "imx8ulp.dtsi"
+
+/ {
+	model = "NXP i.MX8ULP EVK";
+	compatible = "fsl,imx8ulp-evk", "fsl,imx8ulp";
+
+	chosen {
+		stdout-path = &lpuart5;
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x0 0x80000000 0 0x80000000>;
+	};
+
+	clock_ext_rmii: clock-ext-rmii {
+		compatible = "fixed-clock";
+		clock-frequency = <50000000>;
+		clock-output-names = "ext_rmii_clk";
+		#clock-cells = <0>;
+	};
+
+	clock_ext_ts: clock-ext-ts {
+		compatible = "fixed-clock";
+		/* External ts clock is 50MHZ from PHY on EVK board. */
+		clock-frequency = <50000000>;
+		clock-output-names = "ext_ts_clk";
+		#clock-cells = <0>;
+	};
+};
+
+&lpuart5 {
+	/* console */
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&pinctrl_lpuart5>;
+	pinctrl-1 = <&pinctrl_lpuart5>;
+	status = "okay";
+};
+
+&usdhc0 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&pinctrl_usdhc0>;
+	pinctrl-1 = <&pinctrl_usdhc0>;
+	non-removable;
+	bus-width = <8>;
+	status = "okay";
+};
+
+&fec {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&pinctrl_enet>;
+	pinctrl-1 = <&pinctrl_enet>;
+	clocks = <&cgc1 IMX8ULP_CLK_XBAR_DIVBUS>,
+		 <&pcc4 IMX8ULP_CLK_ENET>,
+		 <&cgc1 IMX8ULP_CLK_ENET_TS_SEL>,
+		 <&clock_ext_rmii>;
+	clock-names = "ipg", "ahb", "ptp", "enet_clk_ref";
+	assigned-clocks = <&cgc1 IMX8ULP_CLK_ENET_TS_SEL>;
+	assigned-clock-parents = <&clock_ext_ts>;
+	phy-mode = "rmii";
+	phy-handle = <&ethphy>;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy: ethernet-phy@1 {
+			reg = <1>;
+			micrel,led-mode = <1>;
+		};
+	};
+};
+
+&iomuxc1 {
+	pinctrl_enet: enetgrp {
+		fsl,pins = <
+			MX8ULP_PAD_PTE15__ENET0_MDC     0x43
+			MX8ULP_PAD_PTE14__ENET0_MDIO    0x43
+			MX8ULP_PAD_PTE17__ENET0_RXER    0x43
+			MX8ULP_PAD_PTE18__ENET0_CRS_DV  0x43
+			MX8ULP_PAD_PTF1__ENET0_RXD0     0x43
+			MX8ULP_PAD_PTE20__ENET0_RXD1    0x43
+			MX8ULP_PAD_PTE16__ENET0_TXEN    0x43
+			MX8ULP_PAD_PTE23__ENET0_TXD0    0x43
+			MX8ULP_PAD_PTE22__ENET0_TXD1    0x43
+			MX8ULP_PAD_PTE19__ENET0_REFCLK  0x43
+			MX8ULP_PAD_PTF10__ENET0_1588_CLKIN 0x43
+		>;
+	};
+
+	pinctrl_lpuart5: lpuart5grp {
+		fsl,pins = <
+			MX8ULP_PAD_PTF14__LPUART5_TX	0x3
+			MX8ULP_PAD_PTF15__LPUART5_RX	0x3
+		>;
+	};
+
+	pinctrl_usdhc0: usdhc0grp {
+		fsl,pins = <
+			MX8ULP_PAD_PTD1__SDHC0_CMD	0x43
+			MX8ULP_PAD_PTD2__SDHC0_CLK	0x10042
+			MX8ULP_PAD_PTD10__SDHC0_D0	0x43
+			MX8ULP_PAD_PTD9__SDHC0_D1	0x43
+			MX8ULP_PAD_PTD8__SDHC0_D2	0x43
+			MX8ULP_PAD_PTD7__SDHC0_D3	0x43
+			MX8ULP_PAD_PTD6__SDHC0_D4	0x43
+			MX8ULP_PAD_PTD5__SDHC0_D5	0x43
+			MX8ULP_PAD_PTD4__SDHC0_D6	0x43
+			MX8ULP_PAD_PTD3__SDHC0_D7	0x43
+			MX8ULP_PAD_PTD11__SDHC0_DQS	0x10042
+		>;
+	};
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8ulp-pinfunc.h b/arch/arm64/boot/dts/freescale/imx8ulp-pinfunc.h
new file mode 100644
index 000000000000..b204ac79b449
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8ulp-pinfunc.h
@@ -0,0 +1,978 @@
+/* SPDX-License-Identifier: GPL-2.0+ OR MIT */
+/*
+ * Copyright 2021 NXP
+ */
+
+#ifndef __DTS_IMX8ULP_PINFUNC_H
+#define __DTS_IMX8ULP_PINFUNC_H
+
+/*
+ * The pin function ID is a tuple of
+ * <mux_reg input_reg mux_mode input_val>
+ */
+#define MX8ULP_PAD_PTD0__PTD0                                        0x0000 0x0000 0x1 0x0
+#define MX8ULP_PAD_PTD0__I2S6_RX_BCLK                                0x0000 0x0B44 0x7 0x1
+#define MX8ULP_PAD_PTD0__SDHC0_RESET_B                               0x0000 0x0000 0x8 0x0
+#define MX8ULP_PAD_PTD0__FLEXSPI2_B_DQS                              0x0000 0x0974 0x9 0x1
+#define MX8ULP_PAD_PTD0__CLKOUT2                                     0x0000 0x0000 0xa 0x0
+#define MX8ULP_PAD_PTD0__EPDC0_SDCLK_B                               0x0000 0x0000 0xb 0x0
+#define MX8ULP_PAD_PTD0__LP_APD_DBG_MUX_0                            0x0000 0x0000 0xc 0x0
+#define MX8ULP_PAD_PTD0__CLKOUT1                                     0x0000 0x0000 0xd 0x0
+#define MX8ULP_PAD_PTD0__DEBUG_MUX0_0                                0x0000 0x0000 0xe 0x0
+#define MX8ULP_PAD_PTD0__DEBUG_MUX1_0                                0x0000 0x0000 0xf 0x0
+#define MX8ULP_PAD_PTD1__PTD1                                        0x0004 0x0000 0x1 0x0
+#define MX8ULP_PAD_PTD1__I2S6_RX_FS                                  0x0004 0x0B48 0x7 0x1
+#define MX8ULP_PAD_PTD1__SDHC0_CMD                                   0x0004 0x0000 0x8 0x0
+#define MX8ULP_PAD_PTD1__FLEXSPI2_B_DATA7                            0x0004 0x0970 0x9 0x1
+#define MX8ULP_PAD_PTD1__EPDC0_SDCLK                                 0x0004 0x0000 0xb 0x0
+#define MX8ULP_PAD_PTD1__DPI0_PCLK                                   0x0004 0x0000 0xc 0x0
+#define MX8ULP_PAD_PTD1__LP_APD_DBG_MUX_1                            0x0004 0x0000 0xd 0x0
+#define MX8ULP_PAD_PTD1__DEBUG_MUX0_1                                0x0004 0x0000 0xe 0x0
+#define MX8ULP_PAD_PTD1__DEBUG_MUX1_1                                0x0004 0x0000 0xf 0x0
+#define MX8ULP_PAD_PTD2__PTD2                                        0x0008 0x0000 0x1 0x0
+#define MX8ULP_PAD_PTD2__I2S6_RXD0                                   0x0008 0x0B34 0x7 0x1
+#define MX8ULP_PAD_PTD2__SDHC0_CLK                                   0x0008 0x0000 0x8 0x0
+#define MX8ULP_PAD_PTD2__FLEXSPI2_B_DATA6                            0x0008 0x096C 0x9 0x1
+#define MX8ULP_PAD_PTD2__EPDC0_SDLE                                  0x0008 0x0000 0xb 0x0
+#define MX8ULP_PAD_PTD2__DPI0_HSYNC                                  0x0008 0x0000 0xc 0x0
+#define MX8ULP_PAD_PTD2__LP_APD_DBG_MUX_2                            0x0008 0x0000 0xd 0x0
+#define MX8ULP_PAD_PTD2__DEBUG_MUX0_2                                0x0008 0x0000 0xe 0x0
+#define MX8ULP_PAD_PTD2__DEBUG_MUX1_2                                0x0008 0x0000 0xf 0x0
+#define MX8ULP_PAD_PTD3__PTD3                                        0x000C 0x0000 0x1 0x0
+#define MX8ULP_PAD_PTD3__I2S6_RXD1                                   0x000C 0x0B38 0x7 0x1
+#define MX8ULP_PAD_PTD3__SDHC0_D7                                    0x000C 0x0000 0x8 0x0
+#define MX8ULP_PAD_PTD3__FLEXSPI2_B_DATA5                            0x000C 0x0968 0x9 0x1
+#define MX8ULP_PAD_PTD3__EPDC0_GDSP                                  0x000C 0x0000 0xb 0x0
+#define MX8ULP_PAD_PTD3__DPI0_VSYNC                                  0x000C 0x0000 0xc 0x0
+#define MX8ULP_PAD_PTD3__LP_APD_DBG_MUX_3                            0x000C 0x0000 0xd 0x0
+#define MX8ULP_PAD_PTD3__DEBUG_MUX0_3                                0x000C 0x0000 0xe 0x0
+#define MX8ULP_PAD_PTD3__DEBUG_MUX1_3                                0x000C 0x0000 0xf 0x0
+#define MX8ULP_PAD_PTD4__PTD4                                        0x0010 0x0000 0x1 0x0
+#define MX8ULP_PAD_PTD4__EXT_AUD_MCLK3                               0x0010 0x0B14 0x4 0x1
+#define MX8ULP_PAD_PTD4__SDHC0_VS                                    0x0010 0x0000 0x5 0x0
+#define MX8ULP_PAD_PTD4__TPM8_CH5                                    0x0010 0x0B2C 0x6 0x1
+#define MX8ULP_PAD_PTD4__I2S6_MCLK                                   0x0010 0x0000 0x7 0x0
+#define MX8ULP_PAD_PTD4__SDHC0_D6                                    0x0010 0x0000 0x8 0x0
+#define MX8ULP_PAD_PTD4__FLEXSPI2_B_DATA4                            0x0010 0x0964 0x9 0x1
+#define MX8ULP_PAD_PTD4__EPDC0_SDCE0                                 0x0010 0x0000 0xb 0x0
+#define MX8ULP_PAD_PTD4__DPI0_DE                                     0x0010 0x0000 0xc 0x0
+#define MX8ULP_PAD_PTD4__LP_APD_DBG_MUX_4                            0x0010 0x0000 0xd 0x0
+#define MX8ULP_PAD_PTD4__DEBUG_MUX0_4                                0x0010 0x0000 0xe 0x0
+#define MX8ULP_PAD_PTD4__DEBUG_MUX1_4                                0x0010 0x0000 0xf 0x0
+#define MX8ULP_PAD_PTD5__PTD5                                        0x0014 0x0000 0x1 0x0
+#define MX8ULP_PAD_PTD5__SDHC0_CD                                    0x0014 0x0000 0x5 0x0
+#define MX8ULP_PAD_PTD5__TPM8_CH4                                    0x0014 0x0B28 0x6 0x1
+#define MX8ULP_PAD_PTD5__I2S6_TX_BCLK                                0x0014 0x0B4C 0x7 0x1
+#define MX8ULP_PAD_PTD5__SDHC0_D5                                    0x0014 0x0000 0x8 0x0
+#define MX8ULP_PAD_PTD5__FLEXSPI2_B_SS0_B                            0x0014 0x0000 0x9 0x0
+#define MX8ULP_PAD_PTD5__FLEXSPI2_B_SCLK_B                           0x0014 0x0000 0xa 0x0
+#define MX8ULP_PAD_PTD5__EPDC0_D0                                    0x0014 0x0000 0xb 0x0
+#define MX8ULP_PAD_PTD5__DPI0_D0                                     0x0014 0x0000 0xc 0x0
+#define MX8ULP_PAD_PTD5__LP_APD_DBG_MUX_5                            0x0014 0x0000 0xd 0x0
+#define MX8ULP_PAD_PTD5__DEBUG_MUX0_5                                0x0014 0x0000 0xe 0x0
+#define MX8ULP_PAD_PTD5__DEBUG_MUX1_5                                0x0014 0x0000 0xf 0x0
+#define MX8ULP_PAD_PTD6__PTD6                                        0x0018 0x0000 0x1 0x0
+#define MX8ULP_PAD_PTD6__SDHC0_WP                                    0x0018 0x0000 0x5 0x0
+#define MX8ULP_PAD_PTD6__TPM8_CH3                                    0x0018 0x0B24 0x6 0x1
+#define MX8ULP_PAD_PTD6__I2S6_TX_FS                                  0x0018 0x0B50 0x7 0x1
+#define MX8ULP_PAD_PTD6__SDHC0_D4                                    0x0018 0x0000 0x8 0x0
+#define MX8ULP_PAD_PTD6__FLEXSPI2_B_SCLK                             0x0018 0x0978 0x9 0x1
+#define MX8ULP_PAD_PTD6__EPDC0_D1                                    0x0018 0x0000 0xb 0x0
+#define MX8ULP_PAD_PTD6__DPI0_D1                                     0x0018 0x0000 0xc 0x0
+#define MX8ULP_PAD_PTD6__LP_APD_DBG_MUX_6                            0x0018 0x0000 0xd 0x0
+#define MX8ULP_PAD_PTD6__DEBUG_MUX0_6                                0x0018 0x0000 0xe 0x0
+#define MX8ULP_PAD_PTD6__DEBUG_MUX1_6                                0x0018 0x0000 0xf 0x0
+#define MX8ULP_PAD_PTD7__PTD7                                        0x001C 0x0000 0x1 0x0
+#define MX8ULP_PAD_PTD7__TPM8_CH2                                    0x001C 0x0B20 0x6 0x1
+#define MX8ULP_PAD_PTD7__I2S6_TXD0                                   0x001C 0x0000 0x7 0x0
+#define MX8ULP_PAD_PTD7__SDHC0_D3                                    0x001C 0x0000 0x8 0x0
+#define MX8ULP_PAD_PTD7__FLEXSPI2_B_DATA3                            0x001C 0x0960 0x9 0x1
+#define MX8ULP_PAD_PTD7__EPDC0_D2                                    0x001C 0x0000 0xb 0x0
+#define MX8ULP_PAD_PTD7__DPI0_D2                                     0x001C 0x0000 0xc 0x0
+#define MX8ULP_PAD_PTD7__LP_APD_DBG_MUX_7                            0x001C 0x0000 0xd 0x0
+#define MX8ULP_PAD_PTD7__DEBUG_MUX0_7                                0x001C 0x0000 0xe 0x0
+#define MX8ULP_PAD_PTD7__DEBUG_MUX1_7                                0x001C 0x0000 0xf 0x0
+#define MX8ULP_PAD_PTD8__PTD8                                        0x0020 0x0000 0x1 0x0
+#define MX8ULP_PAD_PTD8__TPM8_CH1                                    0x0020 0x0B1C 0x6 0x1
+#define MX8ULP_PAD_PTD8__I2S6_TXD1                                   0x0020 0x0000 0x7 0x0
+#define MX8ULP_PAD_PTD8__SDHC0_D2                                    0x0020 0x0000 0x8 0x0
+#define MX8ULP_PAD_PTD8__FLEXSPI2_B_DATA2                            0x0020 0x095C 0x9 0x1
+#define MX8ULP_PAD_PTD8__EPDC0_D3                                    0x0020 0x0000 0xb 0x0
+#define MX8ULP_PAD_PTD8__DPI0_D3                                     0x0020 0x0000 0xc 0x0
+#define MX8ULP_PAD_PTD8__LP_APD_DBG_MUX_8                            0x0020 0x0000 0xe 0x0
+#define MX8ULP_PAD_PTD8__DEBUG_MUX1_8                                0x0020 0x0000 0xf 0x0
+#define MX8ULP_PAD_PTD9__PTD9                                        0x0024 0x0000 0x1 0x0
+#define MX8ULP_PAD_PTD9__TPM8_CLKIN                                  0x0024 0x0B30 0x6 0x1
+#define MX8ULP_PAD_PTD9__I2S6_TXD2                                   0x0024 0x0000 0x7 0x0
+#define MX8ULP_PAD_PTD9__SDHC0_D1                                    0x0024 0x0000 0x8 0x0
+#define MX8ULP_PAD_PTD9__FLEXSPI2_B_DATA1                            0x0024 0x0958 0x9 0x1
+#define MX8ULP_PAD_PTD9__EPDC0_D4                                    0x0024 0x0000 0xb 0x0
+#define MX8ULP_PAD_PTD9__DPI0_D4                                     0x0024 0x0000 0xc 0x0
+#define MX8ULP_PAD_PTD9__LP_APD_DBG_MUX_9                            0x0024 0x0000 0xe 0x0
+#define MX8ULP_PAD_PTD9__DEBUG_MUX1_9                                0x0024 0x0000 0xf 0x0
+#define MX8ULP_PAD_PTD10__PTD10                                      0x0028 0x0000 0x1 0x0
+#define MX8ULP_PAD_PTD10__TPM8_CH0                                   0x0028 0x0B18 0x6 0x1
+#define MX8ULP_PAD_PTD10__I2S6_TXD3                                  0x0028 0x0000 0x7 0x0
+#define MX8ULP_PAD_PTD10__SDHC0_D0                                   0x0028 0x0000 0x8 0x0
+#define MX8ULP_PAD_PTD10__FLEXSPI2_B_DATA0                           0x0028 0x0954 0x9 0x1
+#define MX8ULP_PAD_PTD10__EPDC0_D5                                   0x0028 0x0000 0xb 0x0
+#define MX8ULP_PAD_PTD10__DPI0_D5                                    0x0028 0x0000 0xc 0x0
+#define MX8ULP_PAD_PTD10__LP_APD_DBG_MUX_10                          0x0028 0x0000 0xe 0x0
+#define MX8ULP_PAD_PTD10__DEBUG_MUX1_10                              0x0028 0x0000 0xf 0x0
+#define MX8ULP_PAD_PTD11__PTD11                                      0x002C 0x0000 0x1 0x0
+#define MX8ULP_PAD_PTD11__TPM8_CH5                                   0x002C 0x0B2C 0x6 0x2
+#define MX8ULP_PAD_PTD11__I2S6_RXD2                                  0x002C 0x0B3C 0x7 0x1
+#define MX8ULP_PAD_PTD11__SDHC0_DQS                                  0x002C 0x0000 0x8 0x0
+#define MX8ULP_PAD_PTD11__FLEXSPI2_B_SS0_B                           0x002C 0x0000 0x9 0x0
+#define MX8ULP_PAD_PTD11__FLEXSPI2_A_SS1_B                           0x002C 0x0000 0xa 0x0
+#define MX8ULP_PAD_PTD11__EPDC0_D6                                   0x002C 0x0000 0xb 0x0
+#define MX8ULP_PAD_PTD11__DPI0_D6                                    0x002C 0x0000 0xc 0x0
+#define MX8ULP_PAD_PTD11__LP_APD_DBG_MUX_11                          0x002C 0x0000 0xf 0x0
+#define MX8ULP_PAD_PTD12__PTD12                                      0x0030 0x0000 0x1 0x0
+#define MX8ULP_PAD_PTD12__USB0_ID                                    0x0030 0x0AC8 0x5 0x1
+#define MX8ULP_PAD_PTD12__SDHC2_D3                                   0x0030 0x0AA4 0x6 0x1
+#define MX8ULP_PAD_PTD12__I2S7_RX_BCLK                               0x0030 0x0B64 0x7 0x1
+#define MX8ULP_PAD_PTD12__SDHC1_DQS                                  0x0030 0x0A84 0x8 0x1
+#define MX8ULP_PAD_PTD12__FLEXSPI2_A_SS0_B                           0x0030 0x0000 0x9 0x0
+#define MX8ULP_PAD_PTD12__FLEXSPI2_B_SS1_B                           0x0030 0x0000 0xa 0x0
+#define MX8ULP_PAD_PTD12__EPDC0_D7                                   0x0030 0x0000 0xb 0x0
+#define MX8ULP_PAD_PTD12__DPI0_D7                                    0x0030 0x0000 0xc 0x0
+#define MX8ULP_PAD_PTD12__LP_APD_DBG_MUX_12                          0x0030 0x0000 0xf 0x0
+#define MX8ULP_PAD_PTD13__PTD13                                      0x0034 0x0000 0x1 0x0
+#define MX8ULP_PAD_PTD13__SPDIF_IN3                                  0x0034 0x0B80 0x4 0x1
+#define MX8ULP_PAD_PTD13__USB0_PWR                                   0x0034 0x0000 0x5 0x0
+#define MX8ULP_PAD_PTD13__SDHC2_D2                                   0x0034 0x0AA0 0x6 0x1
+#define MX8ULP_PAD_PTD13__I2S7_RX_FS                                 0x0034 0x0B68 0x7 0x1
+#define MX8ULP_PAD_PTD13__SDHC1_RESET_B                              0x0034 0x0000 0x8 0x0
+#define MX8ULP_PAD_PTD13__FLEXSPI2_A_SCLK                            0x0034 0x0000 0x9 0x0
+#define MX8ULP_PAD_PTD13__CLKOUT2                                    0x0034 0x0000 0xa 0x0
+#define MX8ULP_PAD_PTD13__EPDC0_D8                                   0x0034 0x0000 0xb 0x0
+#define MX8ULP_PAD_PTD13__DPI0_D8                                    0x0034 0x0000 0xc 0x0
+#define MX8ULP_PAD_PTD13__CLKOUT1                                    0x0034 0x0000 0xd 0x0
+#define MX8ULP_PAD_PTD13__LP_APD_DBG_MUX_13                          0x0034 0x0000 0xf 0x0
+#define MX8ULP_PAD_PTD14__PTD14                                      0x0038 0x0000 0x1 0x0
+#define MX8ULP_PAD_PTD14__SPDIF_OUT3                                 0x0038 0x0000 0x4 0x0
+#define MX8ULP_PAD_PTD14__USB0_OC                                    0x0038 0x0AC0 0x5 0x1
+#define MX8ULP_PAD_PTD14__SDHC2_D1                                   0x0038 0x0A9C 0x6 0x1
+#define MX8ULP_PAD_PTD14__I2S7_RXD0                                  0x0038 0x0B54 0x7 0x1
+#define MX8ULP_PAD_PTD14__SDHC1_D7                                   0x0038 0x0A80 0x8 0x1
+#define MX8ULP_PAD_PTD14__FLEXSPI2_A_DATA3                           0x0038 0x0000 0x9 0x0
+#define MX8ULP_PAD_PTD14__TRACE0_D7                                  0x0038 0x0000 0xa 0x0
+#define MX8ULP_PAD_PTD14__EPDC0_D9                                   0x0038 0x0000 0xb 0x0
+#define MX8ULP_PAD_PTD14__DPI0_D9                                    0x0038 0x0000 0xc 0x0
+#define MX8ULP_PAD_PTD14__LP_APD_DBG_MUX_14                          0x0038 0x0000 0xf 0x0
+#define MX8ULP_PAD_PTD15__PTD15                                      0x003C 0x0000 0x1 0x0
+#define MX8ULP_PAD_PTD15__SPDIF_IN2                                  0x003C 0x0B7C 0x4 0x1
+#define MX8ULP_PAD_PTD15__SDHC1_VS                                   0x003C 0x0000 0x5 0x0
+#define MX8ULP_PAD_PTD15__SDHC2_D0                                   0x003C 0x0A98 0x6 0x1
+#define MX8ULP_PAD_PTD15__I2S7_TX_BCLK                               0x003C 0x0B6C 0x7 0x1
+#define MX8ULP_PAD_PTD15__SDHC1_D6                                   0x003C 0x0A7C 0x8 0x1
+#define MX8ULP_PAD_PTD15__FLEXSPI2_A_DATA2                           0x003C 0x0000 0x9 0x0
+#define MX8ULP_PAD_PTD15__TRACE0_D6                                  0x003C 0x0000 0xa 0x0
+#define MX8ULP_PAD_PTD15__EPDC0_D10                                  0x003C 0x0000 0xb 0x0
+#define MX8ULP_PAD_PTD15__DPI0_D10                                   0x003C 0x0000 0xc 0x0
+#define MX8ULP_PAD_PTD15__LP_APD_DBG_MUX_15                          0x003C 0x0000 0xf 0x0
+#define MX8ULP_PAD_PTD16__PTD16                                      0x0040 0x0000 0x1 0x0
+#define MX8ULP_PAD_PTD16__FXIO1_D31                                  0x0040 0x08A0 0x2 0x1
+#define MX8ULP_PAD_PTD16__LPSPI4_PCS1                                0x0040 0x08F8 0x3 0x1
+#define MX8ULP_PAD_PTD16__SPDIF_OUT2                                 0x0040 0x0000 0x4 0x0
+#define MX8ULP_PAD_PTD16__SDHC1_CD                                   0x0040 0x0A58 0x5 0x1
+#define MX8ULP_PAD_PTD16__SDHC2_CLK                                  0x0040 0x0A90 0x6 0x1
+#define MX8ULP_PAD_PTD16__I2S7_TX_FS                                 0x0040 0x0B70 0x7 0x1
+#define MX8ULP_PAD_PTD16__SDHC1_D5                                   0x0040 0x0A78 0x8 0x1
+#define MX8ULP_PAD_PTD16__FLEXSPI2_A_DATA1                           0x0040 0x0000 0x9 0x0
+#define MX8ULP_PAD_PTD16__TRACE0_D5                                  0x0040 0x0000 0xa 0x0
+#define MX8ULP_PAD_PTD16__EPDC0_D11                                  0x0040 0x0000 0xb 0x0
+#define MX8ULP_PAD_PTD16__DPI0_D11                                   0x0040 0x0000 0xc 0x0
+#define MX8ULP_PAD_PTD16__LP_APD_DBG_MUX_16                          0x0040 0x0000 0xf 0x0
+#define MX8ULP_PAD_PTD17__PTD17                                      0x0044 0x0000 0x1 0x0
+#define MX8ULP_PAD_PTD17__FXIO1_D30                                  0x0044 0x089C 0x2 0x1
+#define MX8ULP_PAD_PTD17__LPSPI4_PCS2                                0x0044 0x08FC 0x3 0x1
+#define MX8ULP_PAD_PTD17__EXT_AUD_MCLK3                              0x0044 0x0B14 0x4 0x2
+#define MX8ULP_PAD_PTD17__SDHC1_WP                                   0x0044 0x0A88 0x5 0x1
+#define MX8ULP_PAD_PTD17__SDHC2_CMD                                  0x0044 0x0A94 0x6 0x1
+#define MX8ULP_PAD_PTD17__I2S7_TXD0                                  0x0044 0x0000 0x7 0x0
+#define MX8ULP_PAD_PTD17__SDHC1_D4                                   0x0044 0x0A74 0x8 0x1
+#define MX8ULP_PAD_PTD17__FLEXSPI2_A_DATA0                           0x0044 0x0000 0x9 0x0
+#define MX8ULP_PAD_PTD17__TRACE0_D4                                  0x0044 0x0000 0xa 0x0
+#define MX8ULP_PAD_PTD17__EPDC0_D12                                  0x0044 0x0000 0xb 0x0
+#define MX8ULP_PAD_PTD17__DPI0_D12                                   0x0044 0x0000 0xc 0x0
+#define MX8ULP_PAD_PTD17__LP_APD_DBG_MUX_17                          0x0044 0x0000 0xf 0x0
+#define MX8ULP_PAD_PTD18__PTD18                                      0x0048 0x0000 0x1 0x0
+#define MX8ULP_PAD_PTD18__FXIO1_D29                                  0x0048 0x0894 0x2 0x1
+#define MX8ULP_PAD_PTD18__LPSPI4_PCS3                                0x0048 0x0900 0x3 0x1
+#define MX8ULP_PAD_PTD18__SPDIF_CLK                                  0x0048 0x0000 0x4 0x0
+#define MX8ULP_PAD_PTD18__EXT_AUD_MCLK3                              0x0048 0x0B14 0x5 0x3
+#define MX8ULP_PAD_PTD18__TPM8_CH0                                   0x0048 0x0B18 0x6 0x2
+#define MX8ULP_PAD_PTD18__I2S7_MCLK                                  0x0048 0x0000 0x7 0x0
+#define MX8ULP_PAD_PTD18__SDHC1_D3                                   0x0048 0x0A70 0x8 0x1
+#define MX8ULP_PAD_PTD18__FLEXSPI2_A_DQS                             0x0048 0x0000 0x9 0x0
+#define MX8ULP_PAD_PTD18__TRACE0_D3                                  0x0048 0x0000 0xa 0x0
+#define MX8ULP_PAD_PTD18__EPDC0_D13                                  0x0048 0x0000 0xb 0x0
+#define MX8ULP_PAD_PTD18__DPI0_D13                                   0x0048 0x0000 0xc 0x0
+#define MX8ULP_PAD_PTD18__LP_APD_DBG_MUX_18                          0x0048 0x0000 0xf 0x0
+#define MX8ULP_PAD_PTD19__PTD19                                      0x004C 0x0000 0x1 0x0
+#define MX8ULP_PAD_PTD19__FXIO1_D28                                  0x004C 0x0890 0x2 0x1
+#define MX8ULP_PAD_PTD19__SPDIF_IN0                                  0x004C 0x0B74 0x4 0x1
+#define MX8ULP_PAD_PTD19__TPM8_CH1                                   0x004C 0x0B1C 0x6 0x2
+#define MX8ULP_PAD_PTD19__I2S6_RXD3                                  0x004C 0x0B40 0x7 0x1
+#define MX8ULP_PAD_PTD19__SDHC1_D2                                   0x004C 0x0A6C 0x8 0x1
+#define MX8ULP_PAD_PTD19__FLEXSPI2_A_DATA7                           0x004C 0x0000 0x9 0x0
+#define MX8ULP_PAD_PTD19__TRACE0_D2                                  0x004C 0x0000 0xa 0x0
+#define MX8ULP_PAD_PTD19__EPDC0_D14                                  0x004C 0x0000 0xb 0x0
+#define MX8ULP_PAD_PTD19__DPI0_D14                                   0x004C 0x0000 0xc 0x0
+#define MX8ULP_PAD_PTD19__LP_APD_DBG_MUX_19                          0x004C 0x0000 0xf 0x0
+#define MX8ULP_PAD_PTD20__PTD20                                      0x0050 0x0000 0x1 0x0
+#define MX8ULP_PAD_PTD20__FXIO1_D27                                  0x0050 0x088C 0x2 0x1
+#define MX8ULP_PAD_PTD20__LPSPI4_SIN                                 0x0050 0x0908 0x3 0x1
+#define MX8ULP_PAD_PTD20__SPDIF_OUT0                                 0x0050 0x0000 0x4 0x0
+#define MX8ULP_PAD_PTD20__TPM8_CLKIN                                 0x0050 0x0B30 0x6 0x2
+#define MX8ULP_PAD_PTD20__I2S7_RXD1                                  0x0050 0x0B58 0x7 0x1
+#define MX8ULP_PAD_PTD20__SDHC1_D1                                   0x0050 0x0A68 0x8 0x1
+#define MX8ULP_PAD_PTD20__FLEXSPI2_A_DATA6                           0x0050 0x0000 0x9 0x0
+#define MX8ULP_PAD_PTD20__TRACE0_D1                                  0x0050 0x0000 0xa 0x0
+#define MX8ULP_PAD_PTD20__EPDC0_D15                                  0x0050 0x0000 0xb 0x0
+#define MX8ULP_PAD_PTD20__DPI0_D15                                   0x0050 0x0000 0xc 0x0
+#define MX8ULP_PAD_PTD20__LP_APD_DBG_MUX_20                          0x0050 0x0000 0xf 0x0
+#define MX8ULP_PAD_PTD21__PTD21                                      0x0054 0x0000 0x1 0x0
+#define MX8ULP_PAD_PTD21__FXIO1_D26                                  0x0054 0x0888 0x2 0x1
+#define MX8ULP_PAD_PTD21__LPSPI4_SOUT                                0x0054 0x090C 0x3 0x1
+#define MX8ULP_PAD_PTD21__SPDIF_IN1                                  0x0054 0x0B78 0x4 0x1
+#define MX8ULP_PAD_PTD21__USB1_PWR                                   0x0054 0x0000 0x5 0x0
+#define MX8ULP_PAD_PTD21__TPM8_CH2                                   0x0054 0x0B20 0x6 0x2
+#define MX8ULP_PAD_PTD21__I2S7_TXD1                                  0x0054 0x0000 0x7 0x0
+#define MX8ULP_PAD_PTD21__SDHC1_D0                                   0x0054 0x0A64 0x8 0x1
+#define MX8ULP_PAD_PTD21__FLEXSPI2_A_DATA5                           0x0054 0x0000 0x9 0x0
+#define MX8ULP_PAD_PTD21__TRACE0_D0                                  0x0054 0x0000 0xa 0x0
+#define MX8ULP_PAD_PTD21__DPI0_D16                                   0x0054 0x0000 0xc 0x0
+#define MX8ULP_PAD_PTD21__WDOG5_RST                                  0x0054 0x0000 0xd 0x0
+#define MX8ULP_PAD_PTD21__LP_APD_DBG_MUX_21                          0x0054 0x0000 0xf 0x0
+#define MX8ULP_PAD_PTD22__PTD22                                      0x0058 0x0000 0x1 0x0
+#define MX8ULP_PAD_PTD22__FXIO1_D25                                  0x0058 0x0884 0x2 0x1
+#define MX8ULP_PAD_PTD22__LPSPI4_SCK                                 0x0058 0x0904 0x3 0x1
+#define MX8ULP_PAD_PTD22__SPDIF_OUT1                                 0x0058 0x0000 0x4 0x0
+#define MX8ULP_PAD_PTD22__USB1_OC                                    0x0058 0x0AC4 0x5 0x1
+#define MX8ULP_PAD_PTD22__TPM8_CH3                                   0x0058 0x0B24 0x6 0x2
+#define MX8ULP_PAD_PTD22__I2S7_TXD2                                  0x0058 0x0000 0x7 0x0
+#define MX8ULP_PAD_PTD22__SDHC1_CLK                                  0x0058 0x0A5C 0x8 0x1
+#define MX8ULP_PAD_PTD22__FLEXSPI2_A_DATA4                           0x0058 0x0000 0x9 0x0
+#define MX8ULP_PAD_PTD22__TRACE0_CLKOUT                              0x0058 0x0000 0xa 0x0
+#define MX8ULP_PAD_PTD22__DPI0_D17                                   0x0058 0x0000 0xc 0x0
+#define MX8ULP_PAD_PTD22__LP_APD_DBG_MUX_22                          0x0058 0x0000 0xf 0x0
+#define MX8ULP_PAD_PTD23__PTD23                                      0x005C 0x0000 0x1 0x0
+#define MX8ULP_PAD_PTD23__FXIO1_D24                                  0x005C 0x0880 0x2 0x1
+#define MX8ULP_PAD_PTD23__LPSPI4_PCS0                                0x005C 0x08F4 0x3 0x1
+#define MX8ULP_PAD_PTD23__USB1_ID                                    0x005C 0x0ACC 0x5 0x1
+#define MX8ULP_PAD_PTD23__TPM8_CH4                                   0x005C 0x0B28 0x6 0x2
+#define MX8ULP_PAD_PTD23__I2S7_TXD3                                  0x005C 0x0000 0x7 0x0
+#define MX8ULP_PAD_PTD23__SDHC1_CMD                                  0x005C 0x0A60 0x8 0x1
+#define MX8ULP_PAD_PTD23__FLEXSPI2_A_SS0_B                           0x005C 0x0000 0x9 0x0
+#define MX8ULP_PAD_PTD23__FLEXSPI2_A_SCLK_B                          0x005C 0x0000 0xa 0x0
+#define MX8ULP_PAD_PTD23__DPI0_D18                                   0x005C 0x0000 0xc 0x0
+#define MX8ULP_PAD_PTD23__LP_APD_DBG_MUX_23                          0x005C 0x0000 0xf 0x0
+#define MX8ULP_PAD_PTE0__PTE0                                        0x0080 0x0000 0x1 0x0
+#define MX8ULP_PAD_PTE0__FXIO1_D23                                   0x0080 0x087C 0x2 0x1
+#define MX8ULP_PAD_PTE0__SPDIF_IN3                                   0x0080 0x0B80 0x3 0x2
+#define MX8ULP_PAD_PTE0__LPUART4_CTS_B                               0x0080 0x08DC 0x4 0x1
+#define MX8ULP_PAD_PTE0__LPI2C4_SCL                                  0x0080 0x08C8 0x5 0x1
+#define MX8ULP_PAD_PTE0__TPM8_CLKIN                                  0x0080 0x0B30 0x6 0x3
+#define MX8ULP_PAD_PTE0__I2S7_RXD2                                   0x0080 0x0B5C 0x7 0x1
+#define MX8ULP_PAD_PTE0__SDHC2_D1                                    0x0080 0x0A9C 0x8 0x2
+#define MX8ULP_PAD_PTE0__FLEXSPI2_B_DQS                              0x0080 0x0974 0x9 0x2
+#define MX8ULP_PAD_PTE0__ENET0_CRS                                   0x0080 0x0AE8 0xa 0x1
+#define MX8ULP_PAD_PTE0__DBI0_WRX                                    0x0080 0x0000 0xb 0x0
+#define MX8ULP_PAD_PTE0__DPI0_D19                                    0x0080 0x0000 0xc 0x0
+#define MX8ULP_PAD_PTE0__WUU1_P0                                     0x0080 0x0000 0xd 0x0
+#define MX8ULP_PAD_PTE0__DEBUG_MUX0_8                                0x0080 0x0000 0xe 0x0
+#define MX8ULP_PAD_PTE0__DEBUG_MUX1_11                               0x0080 0x0000 0xf 0x0
+#define MX8ULP_PAD_PTE1__PTE1                                        0x0084 0x0000 0x1 0x0
+#define MX8ULP_PAD_PTE1__FXIO1_D22                                   0x0084 0x0878 0x2 0x1
+#define MX8ULP_PAD_PTE1__SPDIF_OUT3                                  0x0084 0x0000 0x3 0x0
+#define MX8ULP_PAD_PTE1__LPUART4_RTS_B                               0x0084 0x0000 0x4 0x0
+#define MX8ULP_PAD_PTE1__LPI2C4_SDA                                  0x0084 0x08CC 0x5 0x1
+#define MX8ULP_PAD_PTE1__TPM8_CH0                                    0x0084 0x0B18 0x6 0x3
+#define MX8ULP_PAD_PTE1__I2S7_RXD3                                   0x0084 0x0B60 0x7 0x1
+#define MX8ULP_PAD_PTE1__SDHC2_D0                                    0x0084 0x0A98 0x8 0x2
+#define MX8ULP_PAD_PTE1__FLEXSPI2_B_DATA7                            0x0084 0x0970 0x9 0x2
+#define MX8ULP_PAD_PTE1__ENET0_COL                                   0x0084 0x0AE4 0xa 0x1
+#define MX8ULP_PAD_PTE1__DBI0_CSX                                    0x0084 0x0000 0xb 0x0
+#define MX8ULP_PAD_PTE1__DPI0_D20                                    0x0084 0x0000 0xc 0x0
+#define MX8ULP_PAD_PTE1__WUU1_P1                                     0x0084 0x0000 0xd 0x0
+#define MX8ULP_PAD_PTE1__DEBUG_MUX0_9                                0x0084 0x0000 0xe 0x0
+#define MX8ULP_PAD_PTE1__DEBUG_MUX1_12                               0x0084 0x0000 0xf 0x0
+#define MX8ULP_PAD_PTE2__PTE2                                        0x0088 0x0000 0x1 0x0
+#define MX8ULP_PAD_PTE2__FXIO1_D21                                   0x0088 0x0874 0x2 0x1
+#define MX8ULP_PAD_PTE2__SPDIF_IN2                                   0x0088 0x0B7C 0x3 0x2
+#define MX8ULP_PAD_PTE2__LPUART4_TX                                  0x0088 0x08E4 0x4 0x1
+#define MX8ULP_PAD_PTE2__LPI2C4_HREQ                                 0x0088 0x08C4 0x5 0x1
+#define MX8ULP_PAD_PTE2__TPM8_CH1                                    0x0088 0x0B1C 0x6 0x3
+#define MX8ULP_PAD_PTE2__EXT_AUD_MCLK3                               0x0088 0x0B14 0x7 0x4
+#define MX8ULP_PAD_PTE2__SDHC2_CLK                                   0x0088 0x0A90 0x8 0x2
+#define MX8ULP_PAD_PTE2__FLEXSPI2_B_DATA6                            0x0088 0x096C 0x9 0x2
+#define MX8ULP_PAD_PTE2__ENET0_TXER                                  0x0088 0x0000 0xa 0x0
+#define MX8ULP_PAD_PTE2__DBI0_DCX                                    0x0088 0x0000 0xb 0x0
+#define MX8ULP_PAD_PTE2__DPI0_D21                                    0x0088 0x0000 0xc 0x0
+#define MX8ULP_PAD_PTE2__LP_HV_DBG_MUX_0                             0x0088 0x0000 0xd 0x0
+#define MX8ULP_PAD_PTE2__DEBUG_MUX0_10                               0x0088 0x0000 0xe 0x0
+#define MX8ULP_PAD_PTE2__DEBUG_MUX1_13                               0x0088 0x0000 0xf 0x0
+#define MX8ULP_PAD_PTE3__PTE3                                        0x008C 0x0000 0x1 0x0
+#define MX8ULP_PAD_PTE3__FXIO1_D20                                   0x008C 0x0870 0x2 0x1
+#define MX8ULP_PAD_PTE3__SPDIF_OUT2                                  0x008C 0x0000 0x3 0x0
+#define MX8ULP_PAD_PTE3__LPUART4_RX                                  0x008C 0x08E0 0x4 0x1
+#define MX8ULP_PAD_PTE3__TPM8_CH2                                    0x008C 0x0B20 0x6 0x3
+#define MX8ULP_PAD_PTE3__I2S6_MCLK                                   0x008C 0x0000 0x7 0x0
+#define MX8ULP_PAD_PTE3__SDHC2_CMD                                   0x008C 0x0A94 0x8 0x2
+#define MX8ULP_PAD_PTE3__FLEXSPI2_B_DATA5                            0x008C 0x0968 0x9 0x2
+#define MX8ULP_PAD_PTE3__ENET0_TXCLK                                 0x008C 0x0B10 0xa 0x1
+#define MX8ULP_PAD_PTE3__DBI0_RWX                                    0x008C 0x0000 0xb 0x0
+#define MX8ULP_PAD_PTE3__DPI0_D22                                    0x008C 0x0000 0xc 0x0
+#define MX8ULP_PAD_PTE3__WUU1_P2                                     0x008C 0x0000 0xd 0x0
+#define MX8ULP_PAD_PTE3__DEBUG_MUX0_11                               0x008C 0x0000 0xe 0x0
+#define MX8ULP_PAD_PTE3__DEBUG_MUX1_14                               0x008C 0x0000 0xf 0x0
+#define MX8ULP_PAD_PTE4__PTE4                                        0x0090 0x0000 0x1 0x0
+#define MX8ULP_PAD_PTE4__FXIO1_D19                                   0x0090 0x0868 0x2 0x1
+#define MX8ULP_PAD_PTE4__SPDIF_CLK                                   0x0090 0x0000 0x3 0x0
+#define MX8ULP_PAD_PTE4__LPUART5_CTS_B                               0x0090 0x08E8 0x4 0x1
+#define MX8ULP_PAD_PTE4__LPI2C5_SCL                                  0x0090 0x08D4 0x5 0x1
+#define MX8ULP_PAD_PTE4__TPM8_CH3                                    0x0090 0x0B24 0x6 0x3
+#define MX8ULP_PAD_PTE4__I2S6_RX_BCLK                                0x0090 0x0B44 0x7 0x2
+#define MX8ULP_PAD_PTE4__SDHC2_D3                                    0x0090 0x0AA4 0x8 0x2
+#define MX8ULP_PAD_PTE4__FLEXSPI2_B_DATA4                            0x0090 0x0964 0x9 0x2
+#define MX8ULP_PAD_PTE4__ENET0_TXD3                                  0x0090 0x0000 0xa 0x0
+#define MX8ULP_PAD_PTE4__DBI0_E                                      0x0090 0x0000 0xb 0x0
+#define MX8ULP_PAD_PTE4__DPI0_D23                                    0x0090 0x0000 0xc 0x0
+#define MX8ULP_PAD_PTE4__WUU1_P3                                     0x0090 0x0000 0xd 0x0
+#define MX8ULP_PAD_PTE4__DEBUG_MUX0_12                               0x0090 0x0000 0xe 0x0
+#define MX8ULP_PAD_PTE4__DEBUG_MUX1_15                               0x0090 0x0000 0xf 0x0
+#define MX8ULP_PAD_PTE5__PTE5                                        0x0094 0x0000 0x1 0x0
+#define MX8ULP_PAD_PTE5__FXIO1_D18                                   0x0094 0x0864 0x2 0x1
+#define MX8ULP_PAD_PTE5__SPDIF_IN0                                   0x0094 0x0B74 0x3 0x2
+#define MX8ULP_PAD_PTE5__LPUART5_RTS_B                               0x0094 0x0000 0x4 0x0
+#define MX8ULP_PAD_PTE5__LPI2C5_SDA                                  0x0094 0x08D8 0x5 0x1
+#define MX8ULP_PAD_PTE5__TPM8_CH4                                    0x0094 0x0B28 0x6 0x3
+#define MX8ULP_PAD_PTE5__I2S6_RX_FS                                  0x0094 0x0B48 0x7 0x2
+#define MX8ULP_PAD_PTE5__SDHC2_D2                                    0x0094 0x0AA0 0x8 0x2
+#define MX8ULP_PAD_PTE5__FLEXSPI2_B_SS0_B                            0x0094 0x0000 0x9 0x0
+#define MX8ULP_PAD_PTE5__ENET0_TXD2                                  0x0094 0x0000 0xa 0x0
+#define MX8ULP_PAD_PTE5__DBI0_D0                                     0x0094 0x0000 0xb 0x0
+#define MX8ULP_PAD_PTE5__LP_HV_DBG_MUX_1                             0x0094 0x0000 0xd 0x0
+#define MX8ULP_PAD_PTE5__DEBUG_MUX0_13                               0x0094 0x0000 0xe 0x0
+#define MX8ULP_PAD_PTE5__DEBUG_MUX1_16                               0x0094 0x0000 0xf 0x0
+#define MX8ULP_PAD_PTE6__PTE6                                        0x0098 0x0000 0x1 0x0
+#define MX8ULP_PAD_PTE6__FXIO1_D17                                   0x0098 0x0860 0x2 0x1
+#define MX8ULP_PAD_PTE6__SPDIF_OUT0                                  0x0098 0x0000 0x3 0x0
+#define MX8ULP_PAD_PTE6__LPUART5_TX                                  0x0098 0x08F0 0x4 0x1
+#define MX8ULP_PAD_PTE6__LPI2C5_HREQ                                 0x0098 0x08D0 0x5 0x1
+#define MX8ULP_PAD_PTE6__TPM8_CH5                                    0x0098 0x0B2C 0x6 0x3
+#define MX8ULP_PAD_PTE6__I2S6_RXD0                                   0x0098 0x0B34 0x7 0x2
+#define MX8ULP_PAD_PTE6__SDHC2_D4                                    0x0098 0x0AA8 0x8 0x1
+#define MX8ULP_PAD_PTE6__FLEXSPI2_B_SCLK                             0x0098 0x0978 0x9 0x2
+#define MX8ULP_PAD_PTE6__ENET0_RXCLK                                 0x0098 0x0B0C 0xa 0x1
+#define MX8ULP_PAD_PTE6__DBI0_D1                                     0x0098 0x0000 0xb 0x0
+#define MX8ULP_PAD_PTE6__LP_HV_DBG_MUX_2                             0x0098 0x0000 0xc 0x0
+#define MX8ULP_PAD_PTE6__WDOG5_RST                                   0x0098 0x0000 0xd 0x0
+#define MX8ULP_PAD_PTE6__DEBUG_MUX0_14                               0x0098 0x0000 0xe 0x0
+#define MX8ULP_PAD_PTE6__DEBUG_MUX1_17                               0x0098 0x0000 0xf 0x0
+#define MX8ULP_PAD_PTE7__PTE7                                        0x009C 0x0000 0x1 0x0
+#define MX8ULP_PAD_PTE7__FXIO1_D16                                   0x009C 0x085C 0x2 0x1
+#define MX8ULP_PAD_PTE7__SPDIF_IN1                                   0x009C 0x0B78 0x3 0x2
+#define MX8ULP_PAD_PTE7__LPUART5_RX                                  0x009C 0x08EC 0x4 0x1
+#define MX8ULP_PAD_PTE7__LPI2C6_HREQ                                 0x009C 0x09B4 0x5 0x1
+#define MX8ULP_PAD_PTE7__TPM4_CLKIN                                  0x009C 0x081C 0x6 0x1
+#define MX8ULP_PAD_PTE7__I2S6_RXD1                                   0x009C 0x0B38 0x7 0x2
+#define MX8ULP_PAD_PTE7__SDHC2_D5                                    0x009C 0x0AAC 0x8 0x1
+#define MX8ULP_PAD_PTE7__FLEXSPI2_B_DATA3                            0x009C 0x0960 0x9 0x2
+#define MX8ULP_PAD_PTE7__ENET0_RXD3                                  0x009C 0x0B04 0xa 0x1
+#define MX8ULP_PAD_PTE7__DBI0_D2                                     0x009C 0x0000 0xb 0x0
+#define MX8ULP_PAD_PTE7__EPDC0_BDR1                                  0x009C 0x0000 0xc 0x0
+#define MX8ULP_PAD_PTE7__WUU1_P4                                     0x009C 0x0000 0xd 0x0
+#define MX8ULP_PAD_PTE7__DEBUG_MUX0_15                               0x009C 0x0000 0xe 0x0
+#define MX8ULP_PAD_PTE7__DEBUG_MUX1_18                               0x009C 0x0000 0xf 0x0
+#define MX8ULP_PAD_PTE8__PTE8                                        0x00A0 0x0000 0x1 0x0
+#define MX8ULP_PAD_PTE8__FXIO1_D15                                   0x00A0 0x0858 0x2 0x1
+#define MX8ULP_PAD_PTE8__LPSPI4_PCS1                                 0x00A0 0x08F8 0x3 0x2
+#define MX8ULP_PAD_PTE8__LPUART6_CTS_B                               0x00A0 0x09CC 0x4 0x1
+#define MX8ULP_PAD_PTE8__LPI2C6_SCL                                  0x00A0 0x09B8 0x5 0x1
+#define MX8ULP_PAD_PTE8__TPM4_CH0                                    0x00A0 0x0804 0x6 0x1
+#define MX8ULP_PAD_PTE8__I2S6_RXD2                                   0x00A0 0x0B3C 0x7 0x2
+#define MX8ULP_PAD_PTE8__SDHC2_D6                                    0x00A0 0x0AB0 0x8 0x1
+#define MX8ULP_PAD_PTE8__FLEXSPI2_B_DATA2                            0x00A0 0x095C 0x9 0x2
+#define MX8ULP_PAD_PTE8__ENET0_RXD2                                  0x00A0 0x0B00 0xa 0x1
+#define MX8ULP_PAD_PTE8__DBI0_D3                                     0x00A0 0x0000 0xb 0x0
+#define MX8ULP_PAD_PTE8__EPDC0_BDR0                                  0x00A0 0x0000 0xc 0x0
+#define MX8ULP_PAD_PTE8__LP_HV_DBG_MUX_3                             0x00A0 0x0000 0xe 0x0
+#define MX8ULP_PAD_PTE8__DEBUG_MUX1_19                               0x00A0 0x0000 0xf 0x0
+#define MX8ULP_PAD_PTE9__PTE9                                        0x00A4 0x0000 0x1 0x0
+#define MX8ULP_PAD_PTE9__FXIO1_D14                                   0x00A4 0x0854 0x2 0x1
+#define MX8ULP_PAD_PTE9__LPSPI4_PCS2                                 0x00A4 0x08FC 0x3 0x2
+#define MX8ULP_PAD_PTE9__LPUART6_RTS_B                               0x00A4 0x0000 0x4 0x0
+#define MX8ULP_PAD_PTE9__LPI2C6_SDA                                  0x00A4 0x09BC 0x5 0x1
+#define MX8ULP_PAD_PTE9__TPM4_CH1                                    0x00A4 0x0808 0x6 0x1
+#define MX8ULP_PAD_PTE9__I2S6_RXD3                                   0x00A4 0x0B40 0x7 0x2
+#define MX8ULP_PAD_PTE9__SDHC2_D7                                    0x00A4 0x0AB4 0x8 0x1
+#define MX8ULP_PAD_PTE9__FLEXSPI2_B_DATA1                            0x00A4 0x0958 0x9 0x2
+#define MX8ULP_PAD_PTE9__ENET0_1588_TMR3                             0x00A4 0x0AE0 0xa 0x1
+#define MX8ULP_PAD_PTE9__DBI0_D4                                     0x00A4 0x0000 0xb 0x0
+#define MX8ULP_PAD_PTE9__EPDC0_VCOM1                                 0x00A4 0x0000 0xc 0x0
+#define MX8ULP_PAD_PTE9__LP_HV_DBG_MUX_4                             0x00A4 0x0000 0xe 0x0
+#define MX8ULP_PAD_PTE9__DEBUG_MUX1_20                               0x00A4 0x0000 0xf 0x0
+#define MX8ULP_PAD_PTE10__PTE10                                      0x00A8 0x0000 0x1 0x0
+#define MX8ULP_PAD_PTE10__FXIO1_D13                                  0x00A8 0x0850 0x2 0x1
+#define MX8ULP_PAD_PTE10__LPSPI4_PCS3                                0x00A8 0x0900 0x3 0x2
+#define MX8ULP_PAD_PTE10__LPUART6_TX                                 0x00A8 0x09D4 0x4 0x1
+#define MX8ULP_PAD_PTE10__I3C2_SCL                                   0x00A8 0x08BC 0x5 0x1
+#define MX8ULP_PAD_PTE10__TPM4_CH2                                   0x00A8 0x080C 0x6 0x1
+#define MX8ULP_PAD_PTE10__I2S6_TX_BCLK                               0x00A8 0x0B4C 0x7 0x2
+#define MX8ULP_PAD_PTE10__SDHC2_DQS                                  0x00A8 0x0AB8 0x8 0x1
+#define MX8ULP_PAD_PTE10__FLEXSPI2_B_DATA0                           0x00A8 0x0954 0x9 0x2
+#define MX8ULP_PAD_PTE10__ENET0_1588_TMR2                            0x00A8 0x0ADC 0xa 0x1
+#define MX8ULP_PAD_PTE10__DBI0_D5                                    0x00A8 0x0000 0xb 0x0
+#define MX8ULP_PAD_PTE10__EPDC0_VCOM0                                0x00A8 0x0000 0xc 0x0
+#define MX8ULP_PAD_PTE10__LP_HV_DBG_MUX_5                            0x00A8 0x0000 0xe 0x0
+#define MX8ULP_PAD_PTE10__DEBUG_MUX1_21                              0x00A8 0x0000 0xf 0x0
+#define MX8ULP_PAD_PTE11__PTE11                                      0x00AC 0x0000 0x1 0x0
+#define MX8ULP_PAD_PTE11__FXIO1_D12                                  0x00AC 0x084C 0x2 0x1
+#define MX8ULP_PAD_PTE11__SPDIF_OUT1                                 0x00AC 0x0000 0x3 0x0
+#define MX8ULP_PAD_PTE11__LPUART6_RX                                 0x00AC 0x09D0 0x4 0x1
+#define MX8ULP_PAD_PTE11__I3C2_SDA                                   0x00AC 0x08C0 0x5 0x1
+#define MX8ULP_PAD_PTE11__TPM4_CH3                                   0x00AC 0x0810 0x6 0x1
+#define MX8ULP_PAD_PTE11__I2S6_TX_FS                                 0x00AC 0x0B50 0x7 0x2
+#define MX8ULP_PAD_PTE11__FLEXSPI2_B_SCLK_B                          0x00AC 0x0000 0x8 0x0
+#define MX8ULP_PAD_PTE11__FLEXSPI2_B_SS0_B                           0x00AC 0x0000 0x9 0x0
+#define MX8ULP_PAD_PTE11__ENET0_1588_TMR1                            0x00AC 0x0AD8 0xa 0x1
+#define MX8ULP_PAD_PTE11__DBI0_D6                                    0x00AC 0x0000 0xb 0x0
+#define MX8ULP_PAD_PTE11__EPDC0_PWRCTRL0                             0x00AC 0x0000 0xc 0x0
+#define MX8ULP_PAD_PTE11__LP_HV_DBG_MUX_6                            0x00AC 0x0000 0xf 0x0
+#define MX8ULP_PAD_PTE12__PTE12                                      0x00B0 0x0000 0x1 0x0
+#define MX8ULP_PAD_PTE12__FXIO1_D11                                  0x00B0 0x0848 0x2 0x1
+#define MX8ULP_PAD_PTE12__LPSPI4_SIN                                 0x00B0 0x0908 0x3 0x2
+#define MX8ULP_PAD_PTE12__LPUART7_CTS_B                              0x00B0 0x09D8 0x4 0x1
+#define MX8ULP_PAD_PTE12__LPI2C7_SCL                                 0x00B0 0x09C4 0x5 0x1
+#define MX8ULP_PAD_PTE12__TPM4_CH4                                   0x00B0 0x0814 0x6 0x1
+#define MX8ULP_PAD_PTE12__I2S6_TXD0                                  0x00B0 0x0000 0x7 0x0
+#define MX8ULP_PAD_PTE12__SDHC2_RESET_B                              0x00B0 0x0000 0x8 0x0
+#define MX8ULP_PAD_PTE12__FLEXSPI2_B_SS1_B                           0x00B0 0x0000 0x9 0x0
+#define MX8ULP_PAD_PTE12__ENET0_1588_TMR0                            0x00B0 0x0AD4 0xa 0x1
+#define MX8ULP_PAD_PTE12__DBI0_D7                                    0x00B0 0x0000 0xb 0x0
+#define MX8ULP_PAD_PTE12__EPDC0_PWRCTRL1                             0x00B0 0x0000 0xc 0x0
+#define MX8ULP_PAD_PTE12__WUU1_P5                                    0x00B0 0x0000 0xd 0x0
+#define MX8ULP_PAD_PTE13__PTE13                                      0x00B4 0x0000 0x1 0x0
+#define MX8ULP_PAD_PTE13__FXIO1_D10                                  0x00B4 0x0844 0x2 0x1
+#define MX8ULP_PAD_PTE13__LPSPI4_SOUT                                0x00B4 0x090C 0x3 0x2
+#define MX8ULP_PAD_PTE13__LPUART7_RTS_B                              0x00B4 0x0000 0x4 0x0
+#define MX8ULP_PAD_PTE13__LPI2C7_SDA                                 0x00B4 0x09C8 0x5 0x1
+#define MX8ULP_PAD_PTE13__TPM4_CH5                                   0x00B4 0x0818 0x6 0x1
+#define MX8ULP_PAD_PTE13__I2S6_TXD1                                  0x00B4 0x0000 0x7 0x0
+#define MX8ULP_PAD_PTE13__SDHC1_WP                                   0x00B4 0x0A88 0x8 0x2
+#define MX8ULP_PAD_PTE13__ENET0_1588_CLKIN                           0x00B4 0x0AD0 0xa 0x1
+#define MX8ULP_PAD_PTE13__DBI0_D8                                    0x00B4 0x0000 0xb 0x0
+#define MX8ULP_PAD_PTE13__EPDC0_PWRCTRL2                             0x00B4 0x0000 0xc 0x0
+#define MX8ULP_PAD_PTE13__LP_HV_DBG_MUX_7                            0x00B4 0x0000 0xf 0x0
+#define MX8ULP_PAD_PTE14__PTE14                                      0x00B8 0x0000 0x1 0x0
+#define MX8ULP_PAD_PTE14__FXIO1_D9                                   0x00B8 0x08B8 0x2 0x1
+#define MX8ULP_PAD_PTE14__LPSPI4_SCK                                 0x00B8 0x0904 0x3 0x2
+#define MX8ULP_PAD_PTE14__LPUART7_TX                                 0x00B8 0x09E0 0x4 0x1
+#define MX8ULP_PAD_PTE14__LPI2C7_HREQ                                0x00B8 0x09C0 0x5 0x1
+#define MX8ULP_PAD_PTE14__TPM5_CLKIN                                 0x00B8 0x0838 0x6 0x1
+#define MX8ULP_PAD_PTE14__I2S6_TXD2                                  0x00B8 0x0000 0x7 0x0
+#define MX8ULP_PAD_PTE14__SDHC1_CD                                   0x00B8 0x0A58 0x8 0x2
+#define MX8ULP_PAD_PTE14__ENET0_MDIO                                 0x00B8 0x0AF0 0xa 0x1
+#define MX8ULP_PAD_PTE14__DBI0_D9                                    0x00B8 0x0000 0xb 0x0
+#define MX8ULP_PAD_PTE14__EPDC0_PWRCTRL3                             0x00B8 0x0000 0xc 0x0
+#define MX8ULP_PAD_PTE14__LP_HV_DBG_MUX_8                            0x00B8 0x0000 0xf 0x0
+#define MX8ULP_PAD_PTE15__PTE15                                      0x00BC 0x0000 0x1 0x0
+#define MX8ULP_PAD_PTE15__FXIO1_D8                                   0x00BC 0x08B4 0x2 0x1
+#define MX8ULP_PAD_PTE15__LPSPI4_PCS0                                0x00BC 0x08F4 0x3 0x2
+#define MX8ULP_PAD_PTE15__LPUART7_RX                                 0x00BC 0x09DC 0x4 0x1
+#define MX8ULP_PAD_PTE15__I3C2_PUR                                   0x00BC 0x0000 0x5 0x0
+#define MX8ULP_PAD_PTE15__TPM5_CH0                                   0x00BC 0x0820 0x6 0x1
+#define MX8ULP_PAD_PTE15__I2S6_TXD3                                  0x00BC 0x0000 0x7 0x0
+#define MX8ULP_PAD_PTE15__MQS1_LEFT                                  0x00BC 0x0000 0x8 0x0
+#define MX8ULP_PAD_PTE15__ENET0_MDC                                  0x00BC 0x0000 0xa 0x0
+#define MX8ULP_PAD_PTE15__DBI0_D10                                   0x00BC 0x0000 0xb 0x0
+#define MX8ULP_PAD_PTE15__EPDC0_PWRCOM                               0x00BC 0x0000 0xc 0x0
+#define MX8ULP_PAD_PTE15__WUU1_P6                                    0x00BC 0x0000 0xd 0x0
+#define MX8ULP_PAD_PTE16__PTE16                                      0x00C0 0x0000 0x1 0x0
+#define MX8ULP_PAD_PTE16__FXIO1_D7                                   0x00C0 0x08B0 0x2 0x1
+#define MX8ULP_PAD_PTE16__LPSPI5_PCS1                                0x00C0 0x0914 0x3 0x1
+#define MX8ULP_PAD_PTE16__LPUART4_CTS_B                              0x00C0 0x08DC 0x4 0x2
+#define MX8ULP_PAD_PTE16__LPI2C4_SCL                                 0x00C0 0x08C8 0x5 0x2
+#define MX8ULP_PAD_PTE16__TPM5_CH1                                   0x00C0 0x0824 0x6 0x1
+#define MX8ULP_PAD_PTE16__MQS1_LEFT                                  0x00C0 0x0000 0x7 0x0
+#define MX8ULP_PAD_PTE16__MQS1_RIGHT                                 0x00C0 0x0000 0x8 0x0
+#define MX8ULP_PAD_PTE16__USB0_ID                                    0x00C0 0x0AC8 0x9 0x2
+#define MX8ULP_PAD_PTE16__ENET0_TXEN                                 0x00C0 0x0000 0xa 0x0
+#define MX8ULP_PAD_PTE16__DBI0_D11                                   0x00C0 0x0000 0xb 0x0
+#define MX8ULP_PAD_PTE16__EPDC0_PWRIRQ                               0x00C0 0x0000 0xc 0x0
+#define MX8ULP_PAD_PTE16__WDOG3_RST                                  0x00C0 0x0000 0xd 0x0
+#define MX8ULP_PAD_PTE16__LP_HV_DBG_MUX_9                            0x00C0 0x0000 0xf 0x0
+#define MX8ULP_PAD_PTE17__PTE17                                      0x00C4 0x0000 0x1 0x0
+#define MX8ULP_PAD_PTE17__FXIO1_D6                                   0x00C4 0x08AC 0x2 0x1
+#define MX8ULP_PAD_PTE17__LPSPI5_PCS2                                0x00C4 0x0918 0x3 0x1
+#define MX8ULP_PAD_PTE17__LPUART4_RTS_B                              0x00C4 0x0000 0x4 0x0
+#define MX8ULP_PAD_PTE17__LPI2C4_SDA                                 0x00C4 0x08CC 0x5 0x2
+#define MX8ULP_PAD_PTE17__MQS1_RIGHT                                 0x00C4 0x0000 0x7 0x0
+#define MX8ULP_PAD_PTE17__SDHC1_VS                                   0x00C4 0x0000 0x8 0x0
+#define MX8ULP_PAD_PTE17__USB0_PWR                                   0x00C4 0x0000 0x9 0x0
+#define MX8ULP_PAD_PTE17__ENET0_RXER                                 0x00C4 0x0B08 0xa 0x1
+#define MX8ULP_PAD_PTE17__DBI0_D12                                   0x00C4 0x0000 0xb 0x0
+#define MX8ULP_PAD_PTE17__EPDC0_PWRSTAT                              0x00C4 0x0000 0xc 0x0
+#define MX8ULP_PAD_PTE17__LP_HV_DBG_MUX_10                           0x00C4 0x0000 0xf 0x0
+#define MX8ULP_PAD_PTE18__PTE18                                      0x00C8 0x0000 0x1 0x0
+#define MX8ULP_PAD_PTE18__FXIO1_D5                                   0x00C8 0x08A8 0x2 0x1
+#define MX8ULP_PAD_PTE18__LPSPI5_PCS3                                0x00C8 0x091C 0x3 0x1
+#define MX8ULP_PAD_PTE18__LPUART4_TX                                 0x00C8 0x08E4 0x4 0x2
+#define MX8ULP_PAD_PTE18__LPI2C4_HREQ                                0x00C8 0x08C4 0x5 0x2
+#define MX8ULP_PAD_PTE18__I2S7_TX_BCLK                               0x00C8 0x0B6C 0x7 0x2
+#define MX8ULP_PAD_PTE18__USB0_OC                                    0x00C8 0x0AC0 0x9 0x2
+#define MX8ULP_PAD_PTE18__ENET0_CRS_DV                               0x00C8 0x0AEC 0xa 0x1
+#define MX8ULP_PAD_PTE18__DBI0_D13                                   0x00C8 0x0000 0xb 0x0
+#define MX8ULP_PAD_PTE18__EPDC0_PWRWAKE                              0x00C8 0x0000 0xc 0x0
+#define MX8ULP_PAD_PTE18__LP_HV_DBG_MUX_11                           0x00C8 0x0000 0xf 0x0
+#define MX8ULP_PAD_PTE19__PTE19                                      0x00CC 0x0000 0x1 0x0
+#define MX8ULP_PAD_PTE19__FXIO1_D4                                   0x00CC 0x08A4 0x2 0x1
+#define MX8ULP_PAD_PTE19__LPUART4_RX                                 0x00CC 0x08E0 0x4 0x2
+#define MX8ULP_PAD_PTE19__LPI2C5_HREQ                                0x00CC 0x08D0 0x5 0x2
+#define MX8ULP_PAD_PTE19__I3C2_PUR                                   0x00CC 0x0000 0x6 0x0
+#define MX8ULP_PAD_PTE19__I2S7_TX_FS                                 0x00CC 0x0B70 0x7 0x2
+#define MX8ULP_PAD_PTE19__USB1_PWR                                   0x00CC 0x0000 0x9 0x0
+#define MX8ULP_PAD_PTE19__ENET0_REFCLK                               0x00CC 0x0AF4 0xa 0x1
+#define MX8ULP_PAD_PTE19__DBI0_D14                                   0x00CC 0x0000 0xb 0x0
+#define MX8ULP_PAD_PTE19__EPDC0_GDCLK                                0x00CC 0x0000 0xc 0x0
+#define MX8ULP_PAD_PTE19__WUU1_P7                                    0x00CC 0x0000 0xd 0x0
+#define MX8ULP_PAD_PTE20__PTE20                                      0x00D0 0x0000 0x1 0x0
+#define MX8ULP_PAD_PTE20__FXIO1_D3                                   0x00D0 0x0898 0x2 0x1
+#define MX8ULP_PAD_PTE20__LPSPI5_SIN                                 0x00D0 0x0924 0x3 0x1
+#define MX8ULP_PAD_PTE20__LPUART5_CTS_B                              0x00D0 0x08E8 0x4 0x2
+#define MX8ULP_PAD_PTE20__LPI2C5_SCL                                 0x00D0 0x08D4 0x5 0x2
+#define MX8ULP_PAD_PTE20__I2S7_TXD0                                  0x00D0 0x0000 0x7 0x0
+#define MX8ULP_PAD_PTE20__USB1_OC                                    0x00D0 0x0AC4 0x9 0x2
+#define MX8ULP_PAD_PTE20__ENET0_RXD1                                 0x00D0 0x0AFC 0xa 0x1
+#define MX8ULP_PAD_PTE20__DBI0_D15                                   0x00D0 0x0000 0xb 0x0
+#define MX8ULP_PAD_PTE20__EPDC0_GDOE                                 0x00D0 0x0000 0xc 0x0
+#define MX8ULP_PAD_PTE20__LP_HV_DBG_MUX_12                           0x00D0 0x0000 0xf 0x0
+#define MX8ULP_PAD_PTE21__PTE21                                      0x00D4 0x0000 0x1 0x0
+#define MX8ULP_PAD_PTE21__FXIO1_D2                                   0x00D4 0x086C 0x2 0x1
+#define MX8ULP_PAD_PTE21__LPSPI5_SOUT                                0x00D4 0x0928 0x3 0x1
+#define MX8ULP_PAD_PTE21__LPUART5_RTS_B                              0x00D4 0x0000 0x4 0x0
+#define MX8ULP_PAD_PTE21__LPI2C5_SDA                                 0x00D4 0x08D8 0x5 0x2
+#define MX8ULP_PAD_PTE21__TPM6_CLKIN                                 0x00D4 0x0994 0x6 0x1
+#define MX8ULP_PAD_PTE21__I2S7_TXD1                                  0x00D4 0x0000 0x7 0x0
+#define MX8ULP_PAD_PTE21__USB1_ID                                    0x00D4 0x0ACC 0x9 0x2
+#define MX8ULP_PAD_PTE21__ENET0_RXD0                                 0x00D4 0x0AF8 0xa 0x1
+#define MX8ULP_PAD_PTE21__EPDC0_GDRL                                 0x00D4 0x0000 0xc 0x0
+#define MX8ULP_PAD_PTE21__WDOG4_RST                                  0x00D4 0x0000 0xd 0x0
+#define MX8ULP_PAD_PTE21__LP_HV_DBG_MUX_13                           0x00D4 0x0000 0xf 0x0
+#define MX8ULP_PAD_PTE22__PTE22                                      0x00D8 0x0000 0x1 0x0
+#define MX8ULP_PAD_PTE22__FXIO1_D1                                   0x00D8 0x0840 0x2 0x1
+#define MX8ULP_PAD_PTE22__LPSPI5_SCK                                 0x00D8 0x0920 0x3 0x1
+#define MX8ULP_PAD_PTE22__LPUART5_TX                                 0x00D8 0x08F0 0x4 0x2
+#define MX8ULP_PAD_PTE22__I3C2_SCL                                   0x00D8 0x08BC 0x5 0x2
+#define MX8ULP_PAD_PTE22__TPM6_CH0                                   0x00D8 0x097C 0x6 0x1
+#define MX8ULP_PAD_PTE22__I2S7_TXD2                                  0x00D8 0x0000 0x7 0x0
+#define MX8ULP_PAD_PTE22__EXT_AUD_MCLK3                              0x00D8 0x0B14 0x9 0x5
+#define MX8ULP_PAD_PTE22__ENET0_TXD1                                 0x00D8 0x0000 0xa 0x0
+#define MX8ULP_PAD_PTE22__EPDC0_SDOED                                0x00D8 0x0000 0xc 0x0
+#define MX8ULP_PAD_PTE22__CLKOUT2                                    0x00D8 0x0000 0xd 0x0
+#define MX8ULP_PAD_PTE22__LP_HV_DBG_MUX_14                           0x00D8 0x0000 0xf 0x0
+#define MX8ULP_PAD_PTE23__PTE23                                      0x00DC 0x0000 0x1 0x0
+#define MX8ULP_PAD_PTE23__FXIO1_D0                                   0x00DC 0x083C 0x2 0x1
+#define MX8ULP_PAD_PTE23__LPSPI5_PCS0                                0x00DC 0x0910 0x3 0x1
+#define MX8ULP_PAD_PTE23__LPUART5_RX                                 0x00DC 0x08EC 0x4 0x2
+#define MX8ULP_PAD_PTE23__I3C2_SDA                                   0x00DC 0x08C0 0x5 0x2
+#define MX8ULP_PAD_PTE23__TPM6_CH1                                   0x00DC 0x0980 0x6 0x1
+#define MX8ULP_PAD_PTE23__I2S7_TXD3                                  0x00DC 0x0000 0x7 0x0
+#define MX8ULP_PAD_PTE23__EXT_AUD_MCLK2                              0x00DC 0x0800 0x9 0x1
+#define MX8ULP_PAD_PTE23__ENET0_TXD0                                 0x00DC 0x0000 0xa 0x0
+#define MX8ULP_PAD_PTE23__EPDC0_SDOEZ                                0x00DC 0x0000 0xc 0x0
+#define MX8ULP_PAD_PTE23__CLKOUT1                                    0x00DC 0x0000 0xd 0x0
+#define MX8ULP_PAD_PTE23__LP_HV_DBG_MUX_15                           0x00DC 0x0000 0xf 0x0
+#define MX8ULP_PAD_PTF0__PTF0                                        0x0100 0x0000 0x1 0x0
+#define MX8ULP_PAD_PTF0__FXIO1_D0                                    0x0100 0x083C 0x2 0x2
+#define MX8ULP_PAD_PTF0__LPUART6_CTS_B                               0x0100 0x09CC 0x4 0x2
+#define MX8ULP_PAD_PTF0__LPI2C6_SCL                                  0x0100 0x09B8 0x5 0x2
+#define MX8ULP_PAD_PTF0__I2S7_RX_BCLK                                0x0100 0x0B64 0x7 0x2
+#define MX8ULP_PAD_PTF0__SDHC1_D1                                    0x0100 0x0A68 0x8 0x2
+#define MX8ULP_PAD_PTF0__ENET0_RXD1                                  0x0100 0x0AFC 0x9 0x2
+#define MX8ULP_PAD_PTF0__USB1_ID                                     0x0100 0x0ACC 0xa 0x3
+#define MX8ULP_PAD_PTF0__EPDC0_SDOE                                  0x0100 0x0000 0xb 0x0
+#define MX8ULP_PAD_PTF0__DPI0_D23                                    0x0100 0x0000 0xc 0x0
+#define MX8ULP_PAD_PTF0__WUU1_P8                                     0x0100 0x0000 0xd 0x0
+#define MX8ULP_PAD_PTF1__PTF1                                        0x0104 0x0000 0x1 0x0
+#define MX8ULP_PAD_PTF1__FXIO1_D1                                    0x0104 0x0840 0x2 0x2
+#define MX8ULP_PAD_PTF1__LPUART6_RTS_B                               0x0104 0x0000 0x4 0x0
+#define MX8ULP_PAD_PTF1__LPI2C6_SDA                                  0x0104 0x09BC 0x5 0x2
+#define MX8ULP_PAD_PTF1__I2S7_RX_FS                                  0x0104 0x0B68 0x7 0x2
+#define MX8ULP_PAD_PTF1__SDHC1_D0                                    0x0104 0x0A64 0x8 0x2
+#define MX8ULP_PAD_PTF1__ENET0_RXD0                                  0x0104 0x0AF8 0x9 0x2
+#define MX8ULP_PAD_PTF1__LP_HV_DBG_MUX_16                            0x0104 0x0000 0xa 0x0
+#define MX8ULP_PAD_PTF1__EPDC0_SDSHR                                 0x0104 0x0000 0xb 0x0
+#define MX8ULP_PAD_PTF1__DPI0_D22                                    0x0104 0x0000 0xc 0x0
+#define MX8ULP_PAD_PTF1__WDOG3_RST                                   0x0104 0x0000 0xd 0x0
+#define MX8ULP_PAD_PTF1__DEBUG_MUX0_16                               0x0104 0x0000 0xe 0x0
+#define MX8ULP_PAD_PTF1__DEBUG_MUX1_22                               0x0104 0x0000 0xf 0x0
+#define MX8ULP_PAD_PTF2__PTF2                                        0x0108 0x0000 0x1 0x0
+#define MX8ULP_PAD_PTF2__FXIO1_D2                                    0x0108 0x086C 0x2 0x2
+#define MX8ULP_PAD_PTF2__LPUART6_TX                                  0x0108 0x09D4 0x4 0x2
+#define MX8ULP_PAD_PTF2__LPI2C6_HREQ                                 0x0108 0x09B4 0x5 0x2
+#define MX8ULP_PAD_PTF2__I2S7_RXD0                                   0x0108 0x0B54 0x7 0x2
+#define MX8ULP_PAD_PTF2__SDHC1_CLK                                   0x0108 0x0A5C 0x8 0x2
+#define MX8ULP_PAD_PTF2__ENET0_TXD1                                  0x0108 0x0000 0x9 0x0
+#define MX8ULP_PAD_PTF2__USB0_ID                                     0x0108 0x0AC8 0xa 0x3
+#define MX8ULP_PAD_PTF2__EPDC0_SDCE9                                 0x0108 0x0000 0xb 0x0
+#define MX8ULP_PAD_PTF2__DPI0_D21                                    0x0108 0x0000 0xc 0x0
+#define MX8ULP_PAD_PTF2__LP_HV_DBG_MUX_17                            0x0108 0x0000 0xd 0x0
+#define MX8ULP_PAD_PTF2__DEBUG_MUX0_17                               0x0108 0x0000 0xe 0x0
+#define MX8ULP_PAD_PTF2__DEBUG_MUX1_23                               0x0108 0x0000 0xf 0x0
+#define MX8ULP_PAD_PTF3__PTF3                                        0x010C 0x0000 0x1 0x0
+#define MX8ULP_PAD_PTF3__FXIO1_D3                                    0x010C 0x0898 0x2 0x2
+#define MX8ULP_PAD_PTF3__LPUART6_RX                                  0x010C 0x09D0 0x4 0x2
+#define MX8ULP_PAD_PTF3__LPI2C7_HREQ                                 0x010C 0x09C0 0x5 0x2
+#define MX8ULP_PAD_PTF3__I2S7_RXD1                                   0x010C 0x0B58 0x7 0x2
+#define MX8ULP_PAD_PTF3__SDHC1_CMD                                   0x010C 0x0A60 0x8 0x2
+#define MX8ULP_PAD_PTF3__ENET0_TXD0                                  0x010C 0x0000 0x9 0x0
+#define MX8ULP_PAD_PTF3__USB0_PWR                                    0x010C 0x0000 0xa 0x0
+#define MX8ULP_PAD_PTF3__EPDC0_SDCE8                                 0x010C 0x0000 0xb 0x0
+#define MX8ULP_PAD_PTF3__DPI0_D20                                    0x010C 0x0000 0xc 0x0
+#define MX8ULP_PAD_PTF3__WUU1_P9                                     0x010C 0x0000 0xd 0x0
+#define MX8ULP_PAD_PTF3__DEBUG_MUX1_24                               0x010C 0x0000 0xf 0x0
+#define MX8ULP_PAD_PTF4__PTF4                                        0x0110 0x0000 0x1 0x0
+#define MX8ULP_PAD_PTF4__FXIO1_D4                                    0x0110 0x08A4 0x2 0x2
+#define MX8ULP_PAD_PTF4__LPSPI4_PCS1                                 0x0110 0x08F8 0x3 0x3
+#define MX8ULP_PAD_PTF4__LPUART7_CTS_B                               0x0110 0x09D8 0x4 0x2
+#define MX8ULP_PAD_PTF4__LPI2C7_SCL                                  0x0110 0x09C4 0x5 0x2
+#define MX8ULP_PAD_PTF4__TPM7_CLKIN                                  0x0110 0x09B0 0x6 0x1
+#define MX8ULP_PAD_PTF4__I2S7_RXD2                                   0x0110 0x0B5C 0x7 0x2
+#define MX8ULP_PAD_PTF4__SDHC1_D3                                    0x0110 0x0A70 0x8 0x2
+#define MX8ULP_PAD_PTF4__ENET0_TXEN                                  0x0110 0x0000 0x9 0x0
+#define MX8ULP_PAD_PTF4__USB0_OC                                     0x0110 0x0AC0 0xa 0x3
+#define MX8ULP_PAD_PTF4__EPDC0_SDCE7                                 0x0110 0x0000 0xb 0x0
+#define MX8ULP_PAD_PTF4__DPI0_D19                                    0x0110 0x0000 0xc 0x0
+#define MX8ULP_PAD_PTF4__WUU1_P10                                    0x0110 0x0000 0xd 0x0
+#define MX8ULP_PAD_PTF4__DEBUG_MUX1_25                               0x0110 0x0000 0xf 0x0
+#define MX8ULP_PAD_PTF5__PTF5                                        0x0114 0x0000 0x1 0x0
+#define MX8ULP_PAD_PTF5__FXIO1_D5                                    0x0114 0x08A8 0x2 0x2
+#define MX8ULP_PAD_PTF5__LPSPI4_PCS2                                 0x0114 0x08FC 0x3 0x3
+#define MX8ULP_PAD_PTF5__LPUART7_RTS_B                               0x0114 0x0000 0x4 0x0
+#define MX8ULP_PAD_PTF5__LPI2C7_SDA                                  0x0114 0x09C8 0x5 0x2
+#define MX8ULP_PAD_PTF5__TPM7_CH0                                    0x0114 0x0998 0x6 0x1
+#define MX8ULP_PAD_PTF5__I2S7_RXD3                                   0x0114 0x0B60 0x7 0x2
+#define MX8ULP_PAD_PTF5__SDHC1_D2                                    0x0114 0x0A6C 0x8 0x2
+#define MX8ULP_PAD_PTF5__ENET0_RXER                                  0x0114 0x0B08 0x9 0x2
+#define MX8ULP_PAD_PTF5__USB1_PWR                                    0x0114 0x0000 0xa 0x0
+#define MX8ULP_PAD_PTF5__EPDC0_SDCE6                                 0x0114 0x0000 0xb 0x0
+#define MX8ULP_PAD_PTF5__DPI0_D18                                    0x0114 0x0000 0xc 0x0
+#define MX8ULP_PAD_PTF5__LP_HV_DBG_MUX_18                            0x0114 0x0000 0xd 0x0
+#define MX8ULP_PAD_PTF5__DEBUG_MUX0_18                               0x0114 0x0000 0xe 0x0
+#define MX8ULP_PAD_PTF5__DEBUG_MUX1_26                               0x0114 0x0000 0xf 0x0
+#define MX8ULP_PAD_PTF6__LP_HV_DBG_MUX_19                            0x0118 0x0000 0x0 0x0
+#define MX8ULP_PAD_PTF6__PTF6                                        0x0118 0x0000 0x1 0x0
+#define MX8ULP_PAD_PTF6__FXIO1_D6                                    0x0118 0x08AC 0x2 0x2
+#define MX8ULP_PAD_PTF6__LPSPI4_PCS3                                 0x0118 0x0900 0x3 0x3
+#define MX8ULP_PAD_PTF6__LPUART7_TX                                  0x0118 0x09E0 0x4 0x2
+#define MX8ULP_PAD_PTF6__I3C2_SCL                                    0x0118 0x08BC 0x5 0x3
+#define MX8ULP_PAD_PTF6__TPM7_CH1                                    0x0118 0x099C 0x6 0x1
+#define MX8ULP_PAD_PTF6__I2S7_MCLK                                   0x0118 0x0000 0x7 0x0
+#define MX8ULP_PAD_PTF6__SDHC1_D4                                    0x0118 0x0A74 0x8 0x2
+#define MX8ULP_PAD_PTF6__ENET0_CRS_DV                                0x0118 0x0AEC 0x9 0x2
+#define MX8ULP_PAD_PTF6__USB1_OC                                     0x0118 0x0AC4 0xa 0x3
+#define MX8ULP_PAD_PTF6__EPDC0_SDCE5                                 0x0118 0x0000 0xb 0x0
+#define MX8ULP_PAD_PTF6__DPI0_D17                                    0x0118 0x0000 0xc 0x0
+#define MX8ULP_PAD_PTF6__WDOG4_RST                                   0x0118 0x0000 0xd 0x0
+#define MX8ULP_PAD_PTF6__DEBUG_MUX0_19                               0x0118 0x0000 0xe 0x0
+#define MX8ULP_PAD_PTF6__DEBUG_MUX1_27                               0x0118 0x0000 0xf 0x0
+#define MX8ULP_PAD_PTF7__PTF7                                        0x011C 0x0000 0x1 0x0
+#define MX8ULP_PAD_PTF7__FXIO1_D7                                    0x011C 0x08B0 0x2 0x2
+#define MX8ULP_PAD_PTF7__LPUART7_RX                                  0x011C 0x09DC 0x4 0x2
+#define MX8ULP_PAD_PTF7__I3C2_SDA                                    0x011C 0x08C0 0x5 0x3
+#define MX8ULP_PAD_PTF7__TPM7_CH2                                    0x011C 0x09A0 0x6 0x1
+#define MX8ULP_PAD_PTF7__MQS1_LEFT                                   0x011C 0x0000 0x7 0x0
+#define MX8ULP_PAD_PTF7__SDHC1_D5                                    0x011C 0x0A78 0x8 0x2
+#define MX8ULP_PAD_PTF7__ENET0_REFCLK                                0x011C 0x0AF4 0x9 0x2
+#define MX8ULP_PAD_PTF7__TRACE0_D15                                  0x011C 0x0000 0xa 0x0
+#define MX8ULP_PAD_PTF7__EPDC0_SDCE4                                 0x011C 0x0000 0xb 0x0
+#define MX8ULP_PAD_PTF7__DPI0_D16                                    0x011C 0x0000 0xc 0x0
+#define MX8ULP_PAD_PTF7__WUU1_P11                                    0x011C 0x0000 0xd 0x0
+#define MX8ULP_PAD_PTF7__DEBUG_MUX1_28                               0x011C 0x0000 0xf 0x0
+#define MX8ULP_PAD_PTF8__PTF8                                        0x0120 0x0000 0x1 0x0
+#define MX8ULP_PAD_PTF8__FXIO1_D8                                    0x0120 0x08B4 0x2 0x2
+#define MX8ULP_PAD_PTF8__LPSPI4_SIN                                  0x0120 0x0908 0x3 0x3
+#define MX8ULP_PAD_PTF8__LPUART4_CTS_B                               0x0120 0x08DC 0x4 0x3
+#define MX8ULP_PAD_PTF8__LPI2C4_SCL                                  0x0120 0x08C8 0x5 0x3
+#define MX8ULP_PAD_PTF8__TPM7_CH3                                    0x0120 0x09A4 0x6 0x1
+#define MX8ULP_PAD_PTF8__MQS1_RIGHT                                  0x0120 0x0000 0x7 0x0
+#define MX8ULP_PAD_PTF8__SDHC1_D6                                    0x0120 0x0A7C 0x8 0x2
+#define MX8ULP_PAD_PTF8__ENET0_MDIO                                  0x0120 0x0AF0 0x9 0x2
+#define MX8ULP_PAD_PTF8__TRACE0_D14                                  0x0120 0x0000 0xa 0x0
+#define MX8ULP_PAD_PTF8__EPDC0_D15                                   0x0120 0x0000 0xb 0x0
+#define MX8ULP_PAD_PTF8__DPI0_D15                                    0x0120 0x0000 0xc 0x0
+#define MX8ULP_PAD_PTF8__LP_HV_DBG_MUX_24                            0x0120 0x0000 0xe 0x0
+#define MX8ULP_PAD_PTF8__DEBUG_MUX1_29                               0x0120 0x0000 0xf 0x0
+#define MX8ULP_PAD_PTF9__PTF9                                        0x0124 0x0000 0x1 0x0
+#define MX8ULP_PAD_PTF9__FXIO1_D9                                    0x0124 0x08B8 0x2 0x2
+#define MX8ULP_PAD_PTF9__LPSPI4_SOUT                                 0x0124 0x090C 0x3 0x3
+#define MX8ULP_PAD_PTF9__LPUART4_RTS_B                               0x0124 0x0000 0x4 0x0
+#define MX8ULP_PAD_PTF9__LPI2C4_SDA                                  0x0124 0x08CC 0x5 0x3
+#define MX8ULP_PAD_PTF9__TPM7_CH4                                    0x0124 0x09A8 0x6 0x1
+#define MX8ULP_PAD_PTF9__EXT_AUD_MCLK2                               0x0124 0x0800 0x7 0x2
+#define MX8ULP_PAD_PTF9__SDHC1_D7                                    0x0124 0x0A80 0x8 0x2
+#define MX8ULP_PAD_PTF9__ENET0_MDC                                   0x0124 0x0000 0x9 0x0
+#define MX8ULP_PAD_PTF9__TRACE0_D13                                  0x0124 0x0000 0xa 0x0
+#define MX8ULP_PAD_PTF9__EPDC0_D14                                   0x0124 0x0000 0xb 0x0
+#define MX8ULP_PAD_PTF9__DPI0_D14                                    0x0124 0x0000 0xc 0x0
+#define MX8ULP_PAD_PTF9__LP_HV_DBG_MUX_25                            0x0124 0x0000 0xe 0x0
+#define MX8ULP_PAD_PTF9__DEBUG_MUX1_30                               0x0124 0x0000 0xf 0x0
+#define MX8ULP_PAD_PTF10__LP_HV_DBG_MUX_26                           0x0128 0x0000 0x0 0x0
+#define MX8ULP_PAD_PTF10__PTF10                                      0x0128 0x0000 0x1 0x0
+#define MX8ULP_PAD_PTF10__FXIO1_D10                                  0x0128 0x0844 0x2 0x2
+#define MX8ULP_PAD_PTF10__LPSPI4_SCK                                 0x0128 0x0904 0x3 0x3
+#define MX8ULP_PAD_PTF10__LPUART4_TX                                 0x0128 0x08E4 0x4 0x3
+#define MX8ULP_PAD_PTF10__LPI2C4_HREQ                                0x0128 0x08C4 0x5 0x3
+#define MX8ULP_PAD_PTF10__TPM7_CH5                                   0x0128 0x09AC 0x6 0x1
+#define MX8ULP_PAD_PTF10__I2S4_RX_BCLK                               0x0128 0x0000 0x7 0x0
+#define MX8ULP_PAD_PTF10__SDHC1_DQS                                  0x0128 0x0A84 0x8 0x2
+#define MX8ULP_PAD_PTF10__ENET0_1588_CLKIN                           0x0128 0x0AD0 0x9 0x2
+#define MX8ULP_PAD_PTF10__TRACE0_D12                                 0x0128 0x0000 0xa 0x0
+#define MX8ULP_PAD_PTF10__EPDC0_D13                                  0x0128 0x0000 0xb 0x0
+#define MX8ULP_PAD_PTF10__DPI0_D13                                   0x0128 0x0000 0xc 0x0
+#define MX8ULP_PAD_PTF10__DEBUG_MUX0_20                              0x0128 0x0000 0xe 0x0
+#define MX8ULP_PAD_PTF10__DEBUG_MUX1_31                              0x0128 0x0000 0xf 0x0
+#define MX8ULP_PAD_PTF11__PTF11                                      0x012C 0x0000 0x1 0x0
+#define MX8ULP_PAD_PTF11__FXIO1_D11                                  0x012C 0x0848 0x2 0x2
+#define MX8ULP_PAD_PTF11__LPSPI4_PCS0                                0x012C 0x08F4 0x3 0x3
+#define MX8ULP_PAD_PTF11__LPUART4_RX                                 0x012C 0x08E0 0x4 0x3
+#define MX8ULP_PAD_PTF11__TPM4_CLKIN                                 0x012C 0x081C 0x6 0x2
+#define MX8ULP_PAD_PTF11__I2S4_RX_FS                                 0x012C 0x0000 0x7 0x0
+#define MX8ULP_PAD_PTF11__SDHC1_RESET_B                              0x012C 0x0000 0x8 0x0
+#define MX8ULP_PAD_PTF11__ENET0_1588_TMR0                            0x012C 0x0AD4 0x9 0x2
+#define MX8ULP_PAD_PTF11__TRACE0_D11                                 0x012C 0x0000 0xa 0x0
+#define MX8ULP_PAD_PTF11__EPDC0_D12                                  0x012C 0x0000 0xb 0x0
+#define MX8ULP_PAD_PTF11__DPI0_D12                                   0x012C 0x0000 0xc 0x0
+#define MX8ULP_PAD_PTF11__LP_HV_DBG_MUX_27                           0x012C 0x0000 0xe 0x0
+#define MX8ULP_PAD_PTF11__DEBUG_MUX1_32                              0x012C 0x0000 0xf 0x0
+#define MX8ULP_PAD_PTF12__PTF12                                      0x0130 0x0000 0x1 0x0
+#define MX8ULP_PAD_PTF12__FXIO1_D12                                  0x0130 0x084C 0x2 0x2
+#define MX8ULP_PAD_PTF12__LPSPI5_PCS1                                0x0130 0x0914 0x3 0x2
+#define MX8ULP_PAD_PTF12__LPUART5_CTS_B                              0x0130 0x08E8 0x4 0x3
+#define MX8ULP_PAD_PTF12__LPI2C5_SCL                                 0x0130 0x08D4 0x5 0x3
+#define MX8ULP_PAD_PTF12__TPM4_CH0                                   0x0130 0x0804 0x6 0x2
+#define MX8ULP_PAD_PTF12__I2S4_RXD0                                  0x0130 0x0000 0x7 0x0
+#define MX8ULP_PAD_PTF12__SDHC2_WP                                   0x0130 0x0ABC 0x8 0x1
+#define MX8ULP_PAD_PTF12__ENET0_1588_TMR1                            0x0130 0x0AD8 0x9 0x2
+#define MX8ULP_PAD_PTF12__TRACE0_D10                                 0x0130 0x0000 0xa 0x0
+#define MX8ULP_PAD_PTF12__EPDC0_D11                                  0x0130 0x0000 0xb 0x0
+#define MX8ULP_PAD_PTF12__DPI0_D11                                   0x0130 0x0000 0xc 0x0
+#define MX8ULP_PAD_PTF12__LP_HV_DBG_MUX_28                           0x0130 0x0000 0xe 0x0
+#define MX8ULP_PAD_PTF12__DEBUG_MUX1_33                              0x0130 0x0000 0xf 0x0
+#define MX8ULP_PAD_PTF13__PTF13                                      0x0134 0x0000 0x1 0x0
+#define MX8ULP_PAD_PTF13__FXIO1_D13                                  0x0134 0x0850 0x2 0x2
+#define MX8ULP_PAD_PTF13__LPSPI5_PCS2                                0x0134 0x0918 0x3 0x2
+#define MX8ULP_PAD_PTF13__LPUART5_RTS_B                              0x0134 0x0000 0x4 0x0
+#define MX8ULP_PAD_PTF13__LPI2C5_SDA                                 0x0134 0x08D8 0x5 0x3
+#define MX8ULP_PAD_PTF13__TPM4_CH1                                   0x0134 0x0808 0x6 0x2
+#define MX8ULP_PAD_PTF13__I2S4_RXD1                                  0x0134 0x0000 0x7 0x0
+#define MX8ULP_PAD_PTF13__SDHC2_CD                                   0x0134 0x0A8C 0x8 0x1
+#define MX8ULP_PAD_PTF13__ENET0_1588_TMR2                            0x0134 0x0ADC 0x9 0x2
+#define MX8ULP_PAD_PTF13__TRACE0_D9                                  0x0134 0x0000 0xa 0x0
+#define MX8ULP_PAD_PTF13__EPDC0_D10                                  0x0134 0x0000 0xb 0x0
+#define MX8ULP_PAD_PTF13__DPI0_D10                                   0x0134 0x0000 0xc 0x0
+#define MX8ULP_PAD_PTF13__DEBUG_MUX0_21                              0x0134 0x0000 0xe 0x0
+#define MX8ULP_PAD_PTF13__LP_HV_DBG_MUX_29                           0x0134 0x0000 0xf 0x0
+#define MX8ULP_PAD_PTF14__PTF14                                      0x0138 0x0000 0x1 0x0
+#define MX8ULP_PAD_PTF14__FXIO1_D14                                  0x0138 0x0854 0x2 0x2
+#define MX8ULP_PAD_PTF14__LPSPI5_PCS3                                0x0138 0x091C 0x3 0x2
+#define MX8ULP_PAD_PTF14__LPUART5_TX                                 0x0138 0x08F0 0x4 0x3
+#define MX8ULP_PAD_PTF14__LPI2C5_HREQ                                0x0138 0x08D0 0x5 0x3
+#define MX8ULP_PAD_PTF14__TPM4_CH2                                   0x0138 0x080C 0x6 0x2
+#define MX8ULP_PAD_PTF14__I2S4_MCLK                                  0x0138 0x0000 0x7 0x0
+#define MX8ULP_PAD_PTF14__SDHC2_VS                                   0x0138 0x0000 0x8 0x0
+#define MX8ULP_PAD_PTF14__ENET0_1588_TMR3                            0x0138 0x0AE0 0x9 0x2
+#define MX8ULP_PAD_PTF14__TRACE0_D8                                  0x0138 0x0000 0xa 0x0
+#define MX8ULP_PAD_PTF14__EPDC0_D9                                   0x0138 0x0000 0xb 0x0
+#define MX8ULP_PAD_PTF14__DPI0_D9                                    0x0138 0x0000 0xc 0x0
+#define MX8ULP_PAD_PTF14__DEBUG_MUX0_22                              0x0138 0x0000 0xe 0x0
+#define MX8ULP_PAD_PTF14__LP_HV_DBG_MUX_30                           0x0138 0x0000 0xf 0x0
+#define MX8ULP_PAD_PTF15__PTF15                                      0x013C 0x0000 0x1 0x0
+#define MX8ULP_PAD_PTF15__FXIO1_D15                                  0x013C 0x0858 0x2 0x2
+#define MX8ULP_PAD_PTF15__LPUART5_RX                                 0x013C 0x08EC 0x4 0x3
+#define MX8ULP_PAD_PTF15__TPM4_CH3                                   0x013C 0x0810 0x6 0x2
+#define MX8ULP_PAD_PTF15__I2S4_TX_BCLK                               0x013C 0x0000 0x7 0x0
+#define MX8ULP_PAD_PTF15__SDHC2_D1                                   0x013C 0x0A9C 0x8 0x3
+#define MX8ULP_PAD_PTF15__ENET0_RXD2                                 0x013C 0x0B00 0x9 0x2
+#define MX8ULP_PAD_PTF15__TRACE0_D7                                  0x013C 0x0000 0xa 0x0
+#define MX8ULP_PAD_PTF15__EPDC0_D8                                   0x013C 0x0000 0xb 0x0
+#define MX8ULP_PAD_PTF15__DPI0_D8                                    0x013C 0x0000 0xc 0x0
+#define MX8ULP_PAD_PTF15__LP_HV_DBG_MUX_31                           0x013C 0x0000 0xf 0x0
+#define MX8ULP_PAD_PTF16__PTF16                                      0x0140 0x0000 0x1 0x0
+#define MX8ULP_PAD_PTF16__FXIO1_D16                                  0x0140 0x085C 0x2 0x2
+#define MX8ULP_PAD_PTF16__LPSPI5_SIN                                 0x0140 0x0924 0x3 0x2
+#define MX8ULP_PAD_PTF16__LPUART6_CTS_B                              0x0140 0x09CC 0x4 0x3
+#define MX8ULP_PAD_PTF16__LPI2C6_SCL                                 0x0140 0x09B8 0x5 0x3
+#define MX8ULP_PAD_PTF16__TPM4_CH4                                   0x0140 0x0814 0x6 0x2
+#define MX8ULP_PAD_PTF16__I2S4_TX_FS                                 0x0140 0x0000 0x7 0x0
+#define MX8ULP_PAD_PTF16__SDHC2_D0                                   0x0140 0x0A98 0x8 0x3
+#define MX8ULP_PAD_PTF16__ENET0_RXD3                                 0x0140 0x0B04 0x9 0x2
+#define MX8ULP_PAD_PTF16__TRACE0_D6                                  0x0140 0x0000 0xa 0x0
+#define MX8ULP_PAD_PTF16__EPDC0_D7                                   0x0140 0x0000 0xb 0x0
+#define MX8ULP_PAD_PTF16__DPI0_D7                                    0x0140 0x0000 0xc 0x0
+#define MX8ULP_PAD_PTF16__LP_HV_DBG_MUX_32                           0x0140 0x0000 0xf 0x0
+#define MX8ULP_PAD_PTF17__PTF17                                      0x0144 0x0000 0x1 0x0
+#define MX8ULP_PAD_PTF17__FXIO1_D17                                  0x0144 0x0860 0x2 0x2
+#define MX8ULP_PAD_PTF17__LPSPI5_SOUT                                0x0144 0x0928 0x3 0x2
+#define MX8ULP_PAD_PTF17__LPUART6_RTS_B                              0x0144 0x0000 0x4 0x0
+#define MX8ULP_PAD_PTF17__LPI2C6_SDA                                 0x0144 0x09BC 0x5 0x3
+#define MX8ULP_PAD_PTF17__TPM4_CH5                                   0x0144 0x0818 0x6 0x2
+#define MX8ULP_PAD_PTF17__I2S4_TXD0                                  0x0144 0x0000 0x7 0x0
+#define MX8ULP_PAD_PTF17__SDHC2_CLK                                  0x0144 0x0A90 0x8 0x3
+#define MX8ULP_PAD_PTF17__ENET0_RXCLK                                0x0144 0x0B0C 0x9 0x2
+#define MX8ULP_PAD_PTF17__TRACE0_D5                                  0x0144 0x0000 0xa 0x0
+#define MX8ULP_PAD_PTF17__EPDC0_D6                                   0x0144 0x0000 0xb 0x0
+#define MX8ULP_PAD_PTF17__DPI0_D6                                    0x0144 0x0000 0xc 0x0
+#define MX8ULP_PAD_PTF17__DEBUG_MUX0_23                              0x0144 0x0000 0xe 0x0
+#define MX8ULP_PAD_PTF17__LP_HV_DBG_MUX_33                           0x0144 0x0000 0xf 0x0
+#define MX8ULP_PAD_PTF18__PTF18                                      0x0148 0x0000 0x1 0x0
+#define MX8ULP_PAD_PTF18__FXIO1_D18                                  0x0148 0x0864 0x2 0x2
+#define MX8ULP_PAD_PTF18__LPSPI5_SCK                                 0x0148 0x0920 0x3 0x2
+#define MX8ULP_PAD_PTF18__LPUART6_TX                                 0x0148 0x09D4 0x4 0x3
+#define MX8ULP_PAD_PTF18__LPI2C6_HREQ                                0x0148 0x09B4 0x5 0x3
+#define MX8ULP_PAD_PTF18__TPM5_CLKIN                                 0x0148 0x0838 0x6 0x2
+#define MX8ULP_PAD_PTF18__I2S4_TXD1                                  0x0148 0x0000 0x7 0x0
+#define MX8ULP_PAD_PTF18__SDHC2_CMD                                  0x0148 0x0A94 0x8 0x3
+#define MX8ULP_PAD_PTF18__ENET0_TXD2                                 0x0148 0x0000 0x9 0x0
+#define MX8ULP_PAD_PTF18__TRACE0_D4                                  0x0148 0x0000 0xa 0x0
+#define MX8ULP_PAD_PTF18__EPDC0_D5                                   0x0148 0x0000 0xb 0x0
+#define MX8ULP_PAD_PTF18__DPI0_D5                                    0x0148 0x0000 0xc 0x0
+#define MX8ULP_PAD_PTF19__PTF19                                      0x014C 0x0000 0x1 0x0
+#define MX8ULP_PAD_PTF19__FXIO1_D19                                  0x014C 0x0868 0x2 0x2
+#define MX8ULP_PAD_PTF19__LPSPI5_PCS0                                0x014C 0x0910 0x3 0x2
+#define MX8ULP_PAD_PTF19__LPUART6_RX                                 0x014C 0x09D0 0x4 0x3
+#define MX8ULP_PAD_PTF19__TPM5_CH0                                   0x014C 0x0820 0x6 0x2
+#define MX8ULP_PAD_PTF19__I2S5_RX_BCLK                               0x014C 0x0000 0x7 0x0
+#define MX8ULP_PAD_PTF19__SDHC2_D3                                   0x014C 0x0AA4 0x8 0x3
+#define MX8ULP_PAD_PTF19__ENET0_TXD3                                 0x014C 0x0000 0x9 0x0
+#define MX8ULP_PAD_PTF19__TRACE0_D3                                  0x014C 0x0000 0xa 0x0
+#define MX8ULP_PAD_PTF19__EPDC0_D4                                   0x014C 0x0000 0xb 0x0
+#define MX8ULP_PAD_PTF19__DPI0_D4                                    0x014C 0x0000 0xc 0x0
+#define MX8ULP_PAD_PTF20__PTF20                                      0x0150 0x0000 0x1 0x0
+#define MX8ULP_PAD_PTF20__FXIO1_D20                                  0x0150 0x0870 0x2 0x2
+#define MX8ULP_PAD_PTF20__LPUART7_CTS_B                              0x0150 0x09D8 0x4 0x3
+#define MX8ULP_PAD_PTF20__LPI2C7_SCL                                 0x0150 0x09C4 0x5 0x3
+#define MX8ULP_PAD_PTF20__TPM5_CH1                                   0x0150 0x0824 0x6 0x2
+#define MX8ULP_PAD_PTF20__I2S5_RX_FS                                 0x0150 0x0000 0x7 0x0
+#define MX8ULP_PAD_PTF20__SDHC2_D2                                   0x0150 0x0AA0 0x8 0x3
+#define MX8ULP_PAD_PTF20__ENET0_TXCLK                                0x0150 0x0B10 0x9 0x2
+#define MX8ULP_PAD_PTF20__TRACE0_D2                                  0x0150 0x0000 0xa 0x0
+#define MX8ULP_PAD_PTF20__EPDC0_D3                                   0x0150 0x0000 0xb 0x0
+#define MX8ULP_PAD_PTF20__DPI0_D3                                    0x0150 0x0000 0xc 0x0
+#define MX8ULP_PAD_PTF21__PTF21                                      0x0154 0x0000 0x1 0x0
+#define MX8ULP_PAD_PTF21__FXIO1_D21                                  0x0154 0x0874 0x2 0x2
+#define MX8ULP_PAD_PTF21__SPDIF_CLK                                  0x0154 0x0000 0x3 0x0
+#define MX8ULP_PAD_PTF21__LPUART7_RTS_B                              0x0154 0x0000 0x4 0x0
+#define MX8ULP_PAD_PTF21__LPI2C7_SDA                                 0x0154 0x09C8 0x5 0x3
+#define MX8ULP_PAD_PTF21__TPM6_CLKIN                                 0x0154 0x0994 0x6 0x2
+#define MX8ULP_PAD_PTF21__I2S5_RXD0                                  0x0154 0x0000 0x7 0x0
+#define MX8ULP_PAD_PTF21__SDHC2_D4                                   0x0154 0x0AA8 0x8 0x2
+#define MX8ULP_PAD_PTF21__ENET0_CRS                                  0x0154 0x0AE8 0x9 0x2
+#define MX8ULP_PAD_PTF21__TRACE0_D1                                  0x0154 0x0000 0xa 0x0
+#define MX8ULP_PAD_PTF21__EPDC0_D2                                   0x0154 0x0000 0xb 0x0
+#define MX8ULP_PAD_PTF21__DPI0_D2                                    0x0154 0x0000 0xc 0x0
+#define MX8ULP_PAD_PTF22__PTF22                                      0x0158 0x0000 0x1 0x0
+#define MX8ULP_PAD_PTF22__FXIO1_D22                                  0x0158 0x0878 0x2 0x2
+#define MX8ULP_PAD_PTF22__SPDIF_IN0                                  0x0158 0x0B74 0x3 0x3
+#define MX8ULP_PAD_PTF22__LPUART7_TX                                 0x0158 0x09E0 0x4 0x3
+#define MX8ULP_PAD_PTF22__LPI2C7_HREQ                                0x0158 0x09C0 0x5 0x3
+#define MX8ULP_PAD_PTF22__TPM6_CH0                                   0x0158 0x097C 0x6 0x2
+#define MX8ULP_PAD_PTF22__I2S5_RXD1                                  0x0158 0x0000 0x7 0x0
+#define MX8ULP_PAD_PTF22__SDHC2_D5                                   0x0158 0x0AAC 0x8 0x2
+#define MX8ULP_PAD_PTF22__ENET0_COL                                  0x0158 0x0AE4 0x9 0x2
+#define MX8ULP_PAD_PTF22__TRACE0_D0                                  0x0158 0x0000 0xa 0x0
+#define MX8ULP_PAD_PTF22__EPDC0_D1                                   0x0158 0x0000 0xb 0x0
+#define MX8ULP_PAD_PTF22__DPI0_D1                                    0x0158 0x0000 0xc 0x0
+#define MX8ULP_PAD_PTF23__PTF23                                      0x015C 0x0000 0x1 0x0
+#define MX8ULP_PAD_PTF23__FXIO1_D23                                  0x015C 0x087C 0x2 0x2
+#define MX8ULP_PAD_PTF23__SPDIF_OUT0                                 0x015C 0x0000 0x3 0x0
+#define MX8ULP_PAD_PTF23__LPUART7_RX                                 0x015C 0x09DC 0x4 0x3
+#define MX8ULP_PAD_PTF23__I3C2_PUR                                   0x015C 0x0000 0x5 0x0
+#define MX8ULP_PAD_PTF23__TPM6_CH1                                   0x015C 0x0980 0x6 0x2
+#define MX8ULP_PAD_PTF23__I2S5_RXD2                                  0x015C 0x0000 0x7 0x0
+#define MX8ULP_PAD_PTF23__SDHC2_D6                                   0x015C 0x0AB0 0x8 0x2
+#define MX8ULP_PAD_PTF23__ENET0_TXER                                 0x015C 0x0000 0x9 0x0
+#define MX8ULP_PAD_PTF23__TRACE0_CLKOUT                              0x015C 0x0000 0xa 0x0
+#define MX8ULP_PAD_PTF23__EPDC0_D0                                   0x015C 0x0000 0xb 0x0
+#define MX8ULP_PAD_PTF23__DPI0_D0                                    0x015C 0x0000 0xc 0x0
+#define MX8ULP_PAD_PTF24__PTF24                                      0x0160 0x0000 0x1 0x0
+#define MX8ULP_PAD_PTF24__FXIO1_D24                                  0x0160 0x0880 0x2 0x2
+#define MX8ULP_PAD_PTF24__SPDIF_IN1                                  0x0160 0x0B78 0x3 0x3
+#define MX8ULP_PAD_PTF24__I3C2_SCL                                   0x0160 0x08BC 0x5 0x4
+#define MX8ULP_PAD_PTF24__I2S5_RXD3                                  0x0160 0x0000 0x7 0x0
+#define MX8ULP_PAD_PTF24__SDHC2_D7                                   0x0160 0x0AB4 0x8 0x2
+#define MX8ULP_PAD_PTF24__DBI0_WRX                                   0x0160 0x0000 0xa 0x0
+#define MX8ULP_PAD_PTF24__EPDC0_SDCLK                                0x0160 0x0000 0xb 0x0
+#define MX8ULP_PAD_PTF24__DPI0_PCLK                                  0x0160 0x0000 0xc 0x0
+#define MX8ULP_PAD_PTF24__WUU1_P12                                   0x0160 0x0000 0xd 0x0
+#define MX8ULP_PAD_PTF25__PTF25                                      0x0164 0x0000 0x1 0x0
+#define MX8ULP_PAD_PTF25__FXIO1_D25                                  0x0164 0x0884 0x2 0x2
+#define MX8ULP_PAD_PTF25__SPDIF_OUT1                                 0x0164 0x0000 0x3 0x0
+#define MX8ULP_PAD_PTF25__I3C2_SDA                                   0x0164 0x08C0 0x5 0x4
+#define MX8ULP_PAD_PTF25__TPM7_CH5                                   0x0164 0x09AC 0x6 0x2
+#define MX8ULP_PAD_PTF25__I2S5_MCLK                                  0x0164 0x0000 0x7 0x0
+#define MX8ULP_PAD_PTF25__SDHC2_DQS                                  0x0164 0x0AB8 0x8 0x2
+#define MX8ULP_PAD_PTF25__EXT_AUD_MCLK2                              0x0164 0x0800 0x9 0x3
+#define MX8ULP_PAD_PTF25__EPDC0_GDSP                                 0x0164 0x0000 0xb 0x0
+#define MX8ULP_PAD_PTF25__DPI0_VSYNC                                 0x0164 0x0000 0xc 0x0
+#define MX8ULP_PAD_PTF25__WUU1_P13                                   0x0164 0x0000 0xd 0x0
+#define MX8ULP_PAD_PTF26__PTF26                                      0x0168 0x0000 0x1 0x0
+#define MX8ULP_PAD_PTF26__FXIO1_D26                                  0x0168 0x0888 0x2 0x2
+#define MX8ULP_PAD_PTF26__SPDIF_IN2                                  0x0168 0x0B7C 0x3 0x3
+#define MX8ULP_PAD_PTF26__TPM7_CLKIN                                 0x0168 0x09B0 0x6 0x2
+#define MX8ULP_PAD_PTF26__I2S5_TX_BCLK                               0x0168 0x0000 0x7 0x0
+#define MX8ULP_PAD_PTF26__SDHC2_RESET_B                              0x0168 0x0000 0x8 0x0
+#define MX8ULP_PAD_PTF26__EPDC0_SDLE                                 0x0168 0x0000 0xb 0x0
+#define MX8ULP_PAD_PTF26__DPI0_HSYNC                                 0x0168 0x0000 0xc 0x0
+#define MX8ULP_PAD_PTF26__WUU1_P14                                   0x0168 0x0000 0xd 0x0
+#define MX8ULP_PAD_PTF27__PTF27                                      0x016C 0x0000 0x1 0x0
+#define MX8ULP_PAD_PTF27__FXIO1_D27                                  0x016C 0x088C 0x2 0x2
+#define MX8ULP_PAD_PTF27__SPDIF_OUT2                                 0x016C 0x0000 0x3 0x0
+#define MX8ULP_PAD_PTF27__TPM7_CH0                                   0x016C 0x0998 0x6 0x2
+#define MX8ULP_PAD_PTF27__I2S5_TX_FS                                 0x016C 0x0000 0x7 0x0
+#define MX8ULP_PAD_PTF27__SDHC2_WP                                   0x016C 0x0ABC 0x8 0x2
+#define MX8ULP_PAD_PTF27__EPDC0_SDCE0                                0x016C 0x0000 0xb 0x0
+#define MX8ULP_PAD_PTF27__DPI0_DE                                    0x016C 0x0000 0xc 0x0
+#define MX8ULP_PAD_PTF27__WUU1_P15                                   0x016C 0x0000 0xd 0x0
+#define MX8ULP_PAD_PTF28__PTF28                                      0x0170 0x0000 0x1 0x0
+#define MX8ULP_PAD_PTF28__FXIO1_D28                                  0x0170 0x0890 0x2 0x2
+#define MX8ULP_PAD_PTF28__SPDIF_IN3                                  0x0170 0x0B80 0x3 0x3
+#define MX8ULP_PAD_PTF28__TPM7_CH1                                   0x0170 0x099C 0x6 0x2
+#define MX8ULP_PAD_PTF28__I2S5_TXD0                                  0x0170 0x0000 0x7 0x0
+#define MX8ULP_PAD_PTF28__SDHC2_CD                                   0x0170 0x0A8C 0x8 0x2
+#define MX8ULP_PAD_PTF28__EPDC0_SDCLK_B                              0x0170 0x0000 0xb 0x0
+#define MX8ULP_PAD_PTF28__LP_HV_DBG_MUX_20                           0x0170 0x0000 0xf 0x0
+#define MX8ULP_PAD_PTF29__PTF29                                      0x0174 0x0000 0x1 0x0
+#define MX8ULP_PAD_PTF29__FXIO1_D29                                  0x0174 0x0894 0x2 0x2
+#define MX8ULP_PAD_PTF29__SPDIF_OUT3                                 0x0174 0x0000 0x3 0x0
+#define MX8ULP_PAD_PTF29__TPM7_CH2                                   0x0174 0x09A0 0x6 0x2
+#define MX8ULP_PAD_PTF29__I2S5_TXD1                                  0x0174 0x0000 0x7 0x0
+#define MX8ULP_PAD_PTF29__SDHC2_VS                                   0x0174 0x0000 0x8 0x0
+#define MX8ULP_PAD_PTF29__EPDC0_SDCE1                                0x0174 0x0000 0xb 0x0
+#define MX8ULP_PAD_PTF29__WDOG3_RST                                  0x0174 0x0000 0xd 0x0
+#define MX8ULP_PAD_PTF29__LP_HV_DBG_MUX_21                           0x0174 0x0000 0xf 0x0
+#define MX8ULP_PAD_PTF30__PTF30                                      0x0178 0x0000 0x1 0x0
+#define MX8ULP_PAD_PTF30__FXIO1_D30                                  0x0178 0x089C 0x2 0x2
+#define MX8ULP_PAD_PTF30__TPM7_CH3                                   0x0178 0x09A4 0x6 0x2
+#define MX8ULP_PAD_PTF30__I2S5_TXD2                                  0x0178 0x0000 0x7 0x0
+#define MX8ULP_PAD_PTF30__MQS1_LEFT                                  0x0178 0x0000 0x8 0x0
+#define MX8ULP_PAD_PTF30__EPDC0_SDCE2                                0x0178 0x0000 0xb 0x0
+#define MX8ULP_PAD_PTF30__WDOG4_RST                                  0x0178 0x0000 0xd 0x0
+#define MX8ULP_PAD_PTF30__LP_HV_DBG_MUX_22                           0x0178 0x0000 0xf 0x0
+#define MX8ULP_PAD_PTF31__PTF31                                      0x017C 0x0000 0x1 0x0
+#define MX8ULP_PAD_PTF31__FXIO1_D31                                  0x017C 0x08A0 0x2 0x2
+#define MX8ULP_PAD_PTF31__TPM7_CH4                                   0x017C 0x09A8 0x6 0x2
+#define MX8ULP_PAD_PTF31__I2S5_TXD3                                  0x017C 0x0000 0x7 0x0
+#define MX8ULP_PAD_PTF31__MQS1_RIGHT                                 0x017C 0x0000 0x8 0x0
+#define MX8ULP_PAD_PTF31__EPDC0_SDCE3                                0x017C 0x0000 0xb 0x0
+#define MX8ULP_PAD_PTF31__WDOG5_RST                                  0x017C 0x0000 0xd 0x0
+#define MX8ULP_PAD_PTF31__LP_HV_DBG_MUX_23                           0x017C 0x0000 0xf 0x0
+#define MX8ULP_PAD_BOOT_MODE0__BOOT_MODE0                            0x0400 0x0000 0x0 0x0
+#define MX8ULP_PAD_BOOT_MODE1__BOOT_MODE1                            0x0404 0x0000 0x0 0x0
+
+#endif /* __DTS_IMX8ULP_PINFUNC_H */
diff --git a/arch/arm64/boot/dts/freescale/imx8ulp.dtsi b/arch/arm64/boot/dts/freescale/imx8ulp.dtsi
new file mode 100644
index 000000000000..06ce5f19aa8a
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8ulp.dtsi
@@ -0,0 +1,476 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2021 NXP
+ */
+
+#include <dt-bindings/clock/imx8ulp-clock.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/power/imx8ulp-power.h>
+
+#include "imx8ulp-pinfunc.h"
+
+/ {
+	interrupt-parent = <&gic>;
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	aliases {
+		ethernet0 = &fec;
+		gpio0 = &gpiod;
+		gpio1 = &gpioe;
+		gpio2 = &gpiof;
+		mmc0 = &usdhc0;
+		mmc1 = &usdhc1;
+		mmc2 = &usdhc2;
+		serial0 = &lpuart4;
+		serial1 = &lpuart5;
+		serial2 = &lpuart6;
+		serial3 = &lpuart7;
+	};
+
+	cpus {
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		A35_0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a35";
+			reg = <0x0 0x0>;
+			enable-method = "psci";
+			next-level-cache = <&A35_L2>;
+		};
+
+		A35_1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a35";
+			reg = <0x0 0x1>;
+			enable-method = "psci";
+			next-level-cache = <&A35_L2>;
+		};
+
+		A35_L2: l2-cache0 {
+			compatible = "cache";
+		};
+	};
+
+	gic: interrupt-controller@2d400000 {
+		compatible = "arm,gic-v3";
+		reg = <0x0 0x2d400000 0 0x10000>, /* GIC Dist */
+		      <0x0 0x2d440000 0 0xc0000>; /* GICR (RD_base + SGI_base) */
+		#interrupt-cells = <3>;
+		interrupt-controller;
+		interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
+	pmu {
+		compatible = "arm,cortex-a35-pmu";
+		interrupt-parent = <&gic>;
+		interrupts = <GIC_PPI 7
+			     (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_HIGH)>;
+		interrupt-affinity = <&A35_0>, <&A35_1>;
+	};
+
+	psci {
+		compatible = "arm,psci-1.0";
+		method = "smc";
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW>, /* Physical Secure */
+			     <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW>, /* Physical Non-Secure */
+			     <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW>, /* Virtual */
+			     <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW>; /* Hypervisor */
+	};
+
+	frosc: clock-frosc {
+		compatible = "fixed-clock";
+		clock-frequency = <192000000>;
+		clock-output-names = "frosc";
+		#clock-cells = <0>;
+	};
+
+	lposc: clock-lposc {
+		compatible = "fixed-clock";
+		clock-frequency = <1000000>;
+		clock-output-names = "lposc";
+		#clock-cells = <0>;
+	};
+
+	rosc: clock-rosc {
+		compatible = "fixed-clock";
+		clock-frequency = <32768>;
+		clock-output-names = "rosc";
+		#clock-cells = <0>;
+	};
+
+	sosc: clock-sosc {
+		compatible = "fixed-clock";
+		clock-frequency = <24000000>;
+		clock-output-names = "sosc";
+		#clock-cells = <0>;
+	};
+
+	sram@2201f000 {
+		compatible = "mmio-sram";
+		reg = <0x0 0x2201f000 0x0 0x1000>;
+
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0x0 0x2201f000 0x1000>;
+
+		scmi_buf: scmi-sram-section@0 {
+			compatible = "arm,scmi-shmem";
+			reg = <0x0 0x400>;
+		};
+	};
+
+	firmware {
+		scmi {
+			compatible = "arm,scmi-smc";
+			arm,smc-id = <0xc20000fe>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			shmem = <&scmi_buf>;
+
+			scmi_devpd: protocol@11 {
+				reg = <0x11>;
+				#power-domain-cells = <1>;
+			};
+
+			scmi_sensor: protocol@15 {
+				reg = <0x15>;
+				#thermal-sensor-cells = <1>;
+			};
+		};
+	};
+
+	soc: soc@0 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x0 0x0 0x40000000>;
+
+		s4muap: mailbox@27020000 {
+			compatible = "fsl,imx8ulp-mu-s4";
+			reg = <0x27020000 0x10000>;
+			interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
+			#mbox-cells = <2>;
+		};
+
+		per_bridge3: bus@29000000 {
+			compatible = "simple-bus";
+			reg = <0x29000000 0x800000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			mu: mailbox@29220000 {
+				compatible = "fsl,imx8ulp-mu";
+				reg = <0x29220000 0x10000>;
+				interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
+				#mbox-cells = <2>;
+				status = "disabled";
+			};
+
+			mu3: mailbox@29230000 {
+				compatible = "fsl,imx8ulp-mu";
+				reg = <0x29230000 0x10000>;
+				interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&pcc3 IMX8ULP_CLK_MU3_A>;
+				#mbox-cells = <2>;
+				status = "disabled";
+			};
+
+			wdog3: watchdog@292a0000 {
+				compatible = "fsl,imx8ulp-wdt", "fsl,imx7ulp-wdt";
+				reg = <0x292a0000 0x10000>;
+				interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&pcc3 IMX8ULP_CLK_WDOG3>;
+				assigned-clocks = <&pcc3 IMX8ULP_CLK_WDOG3>;
+				assigned-clock-parents = <&cgc1 IMX8ULP_CLK_SOSC_DIV2>;
+				timeout-sec = <40>;
+			};
+
+			cgc1: clock-controller@292c0000 {
+				compatible = "fsl,imx8ulp-cgc1";
+				reg = <0x292c0000 0x10000>;
+				#clock-cells = <1>;
+			};
+
+			pcc3: clock-controller@292d0000 {
+				compatible = "fsl,imx8ulp-pcc3";
+				reg = <0x292d0000 0x10000>;
+				#clock-cells = <1>;
+				#reset-cells = <1>;
+			};
+
+			tpm5: tpm@29340000 {
+				compatible = "fsl,imx8ulp-tpm", "fsl,imx7ulp-tpm";
+				reg = <0x29340000 0x1000>;
+				interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&pcc3 IMX8ULP_CLK_TPM5>,
+					 <&pcc3 IMX8ULP_CLK_TPM5>;
+				clock-names = "ipg", "per";
+				status = "disabled";
+			};
+
+			lpi2c4: i2c@29370000 {
+				compatible = "fsl,imx8ulp-lpi2c", "fsl,imx7ulp-lpi2c";
+				reg = <0x29370000 0x10000>;
+				interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&pcc3 IMX8ULP_CLK_LPI2C4>,
+					 <&pcc3 IMX8ULP_CLK_LPI2C4>;
+				clock-names = "per", "ipg";
+				assigned-clocks = <&pcc3 IMX8ULP_CLK_LPI2C4>;
+				assigned-clock-parents = <&cgc1 IMX8ULP_CLK_FROSC_DIV2>;
+				assigned-clock-rates = <48000000>;
+				status = "disabled";
+			};
+
+			lpi2c5: i2c@29380000 {
+				compatible = "fsl,imx8ulp-lpi2c", "fsl,imx7ulp-lpi2c";
+				reg = <0x29380000 0x10000>;
+				interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&pcc3 IMX8ULP_CLK_LPI2C5>,
+					 <&pcc3 IMX8ULP_CLK_LPI2C5>;
+				clock-names = "per", "ipg";
+				assigned-clocks = <&pcc3 IMX8ULP_CLK_LPI2C5>;
+				assigned-clock-parents = <&cgc1 IMX8ULP_CLK_FROSC_DIV2>;
+				assigned-clock-rates = <48000000>;
+				status = "disabled";
+			};
+
+			lpuart4: serial@29390000 {
+				compatible = "fsl,imx8ulp-lpuart", "fsl,imx7ulp-lpuart";
+				reg = <0x29390000 0x1000>;
+				interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&pcc3 IMX8ULP_CLK_LPUART4>;
+				clock-names = "ipg";
+				status = "disabled";
+			};
+
+			lpuart5: serial@293a0000 {
+				compatible = "fsl,imx8ulp-lpuart", "fsl,imx7ulp-lpuart";
+				reg = <0x293a0000 0x1000>;
+				interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&pcc3 IMX8ULP_CLK_LPUART5>;
+				clock-names = "ipg";
+				status = "disabled";
+			};
+
+			lpspi4: spi@293b0000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "fsl,imx8ulp-spi", "fsl,imx7ulp-spi";
+				reg = <0x293b0000 0x10000>;
+				interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&pcc3 IMX8ULP_CLK_LPSPI4>,
+					 <&pcc3 IMX8ULP_CLK_LPSPI4>;
+				clock-names = "per", "ipg";
+				assigned-clocks = <&pcc3 IMX8ULP_CLK_LPSPI4>;
+				assigned-clock-parents = <&cgc1 IMX8ULP_CLK_FROSC_DIV2>;
+				assigned-clock-rates = <48000000>;
+				status = "disabled";
+			};
+
+			lpspi5: spi@293c0000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "fsl,imx8ulp-spi", "fsl,imx7ulp-spi";
+				reg = <0x293c0000 0x10000>;
+				interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&pcc3 IMX8ULP_CLK_LPSPI5>,
+					 <&pcc3 IMX8ULP_CLK_LPSPI5>;
+				clock-names = "per", "ipg";
+				assigned-clocks = <&pcc3 IMX8ULP_CLK_LPSPI5>;
+				assigned-clock-parents = <&cgc1 IMX8ULP_CLK_FROSC_DIV2>;
+				assigned-clock-rates = <48000000>;
+				status = "disabled";
+			};
+		};
+
+		per_bridge4: bus@29800000 {
+			compatible = "simple-bus";
+			reg = <0x29800000 0x800000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			pcc4: clock-controller@29800000 {
+				compatible = "fsl,imx8ulp-pcc4";
+				reg = <0x29800000 0x10000>;
+				#clock-cells = <1>;
+				#reset-cells = <1>;
+			};
+
+			lpi2c6: i2c@29840000 {
+				compatible = "fsl,imx8ulp-lpi2c", "fsl,imx7ulp-lpi2c";
+				reg = <0x29840000 0x10000>;
+				interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&pcc4 IMX8ULP_CLK_LPI2C6>,
+					 <&pcc4 IMX8ULP_CLK_LPI2C6>;
+				clock-names = "per", "ipg";
+				assigned-clocks = <&pcc4 IMX8ULP_CLK_LPI2C6>;
+				assigned-clock-parents = <&cgc1 IMX8ULP_CLK_FROSC_DIV2>;
+				assigned-clock-rates = <48000000>;
+				status = "disabled";
+			};
+
+			lpi2c7: i2c@29850000 {
+				compatible = "fsl,imx8ulp-lpi2c", "fsl,imx7ulp-lpi2c";
+				reg = <0x29850000 0x10000>;
+				interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&pcc4 IMX8ULP_CLK_LPI2C7>,
+					 <&pcc4 IMX8ULP_CLK_LPI2C7>;
+				clock-names = "per", "ipg";
+				assigned-clocks = <&pcc4 IMX8ULP_CLK_LPI2C7>;
+				assigned-clock-parents = <&cgc1 IMX8ULP_CLK_FROSC_DIV2>;
+				assigned-clock-rates = <48000000>;
+				status = "disabled";
+			};
+
+			lpuart6: serial@29860000 {
+				compatible = "fsl,imx8ulp-lpuart", "fsl,imx7ulp-lpuart";
+				reg = <0x29860000 0x1000>;
+				interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&pcc4 IMX8ULP_CLK_LPUART6>;
+				clock-names = "ipg";
+				status = "disabled";
+			};
+
+			lpuart7: serial@29870000 {
+				compatible = "fsl,imx8ulp-lpuart", "fsl,imx7ulp-lpuart";
+				reg = <0x29870000 0x1000>;
+				interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&pcc4 IMX8ULP_CLK_LPUART7>;
+				clock-names = "ipg";
+				status = "disabled";
+			};
+
+			iomuxc1: pinctrl@298c0000 {
+				compatible = "fsl,imx8ulp-iomuxc1";
+				reg = <0x298c0000 0x10000>;
+			};
+
+			usdhc0: mmc@298d0000 {
+				compatible = "fsl,imx8ulp-usdhc", "fsl,imx8mm-usdhc";
+				reg = <0x298d0000 0x10000>;
+				interrupts = <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&cgc1 IMX8ULP_CLK_XBAR_DIVBUS>,
+					 <&cgc1 IMX8ULP_CLK_XBAR_AD_DIVPLAT>,
+					 <&pcc4 IMX8ULP_CLK_USDHC0>;
+				clock-names = "ipg", "ahb", "per";
+				power-domains = <&scmi_devpd IMX8ULP_PD_USDHC0>;
+				fsl,tuning-start-tap = <20>;
+				fsl,tuning-step = <2>;
+				bus-width = <4>;
+				status = "disabled";
+			};
+
+			usdhc1: mmc@298e0000 {
+				compatible = "fsl,imx8ulp-usdhc", "fsl,imx8mm-usdhc";
+				reg = <0x298e0000 0x10000>;
+				interrupts = <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&cgc1 IMX8ULP_CLK_XBAR_DIVBUS>,
+					 <&cgc1 IMX8ULP_CLK_NIC_PER_DIVPLAT>,
+					 <&pcc4 IMX8ULP_CLK_USDHC1>;
+				clock-names = "ipg", "ahb", "per";
+				power-domains = <&scmi_devpd IMX8ULP_PD_USDHC1>;
+				fsl,tuning-start-tap = <20>;
+				fsl,tuning-step = <2>;
+				bus-width = <4>;
+				status = "disabled";
+			};
+
+			usdhc2: mmc@298f0000 {
+				compatible = "fsl,imx8ulp-usdhc", "fsl,imx8mm-usdhc";
+				reg = <0x298f0000 0x10000>;
+				interrupts = <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&cgc1 IMX8ULP_CLK_XBAR_DIVBUS>,
+					 <&cgc1 IMX8ULP_CLK_NIC_PER_DIVPLAT>,
+					 <&pcc4 IMX8ULP_CLK_USDHC2>;
+				clock-names = "ipg", "ahb", "per";
+				power-domains = <&scmi_devpd IMX8ULP_PD_USDHC2_USB1>;
+				fsl,tuning-start-tap = <20>;
+				fsl,tuning-step = <2>;
+				bus-width = <4>;
+				status = "disabled";
+			};
+
+			fec: ethernet@29950000 {
+				compatible = "fsl,imx8ulp-fec", "fsl,imx6ul-fec", "fsl,imx6q-fec";
+				reg = <0x29950000 0x10000>;
+				interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-names = "int0";
+				fsl,num-tx-queues = <1>;
+				fsl,num-rx-queues = <1>;
+				status = "disabled";
+			};
+		};
+
+		gpioe: gpio@2d000080 {
+				compatible = "fsl,imx8ulp-gpio", "fsl,imx7ulp-gpio";
+				reg = <0x2d000080 0x1000>, <0x2d000040 0x40>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupts = <GIC_SPI 129 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				clocks = <&pcc4 IMX8ULP_CLK_RGPIOE>,
+					 <&pcc4 IMX8ULP_CLK_PCTLE>;
+				clock-names = "gpio", "port";
+				gpio-ranges = <&iomuxc1 0 32 24>;
+		};
+
+		gpiof: gpio@2d010080 {
+				compatible = "fsl,imx8ulp-gpio", "fsl,imx7ulp-gpio";
+				reg = <0x2d010080 0x1000>, <0x2d010040 0x40>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				clocks = <&pcc4 IMX8ULP_CLK_RGPIOF>,
+					 <&pcc4 IMX8ULP_CLK_PCTLF>;
+				clock-names = "gpio", "port";
+				gpio-ranges = <&iomuxc1 0 64 32>;
+		};
+
+		per_bridge5: bus@2d800000 {
+			compatible = "simple-bus";
+			reg = <0x2d800000 0x800000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			cgc2: clock-controller@2da60000 {
+				compatible = "fsl,imx8ulp-cgc2";
+				reg = <0x2da60000 0x10000>;
+				#clock-cells = <1>;
+			};
+
+			pcc5: clock-controller@2da70000 {
+				compatible = "fsl,imx8ulp-pcc5";
+				reg = <0x2da70000 0x10000>;
+				#clock-cells = <1>;
+				#reset-cells = <1>;
+			};
+		};
+
+		gpiod: gpio@2e200080 {
+			compatible = "fsl,imx8ulp-gpio", "fsl,imx7ulp-gpio";
+			reg = <0x2e200080 0x1000>, <0x2e200040 0x40>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupts = <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			clocks = <&pcc5 IMX8ULP_CLK_RGPIOD>,
+				 <&pcc5 IMX8ULP_CLK_RGPIOD>;
+			clock-names = "gpio", "port";
+			gpio-ranges = <&iomuxc1 0 0 24>;
+		};
+	};
+};
diff --git a/arch/arm64/boot/dts/freescale/imx93-11x11-evk.dts b/arch/arm64/boot/dts/freescale/imx93-11x11-evk.dts
new file mode 100644
index 000000000000..69786c326db0
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx93-11x11-evk.dts
@@ -0,0 +1,114 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2022 NXP
+ */
+
+/dts-v1/;
+
+#include "imx93.dtsi"
+
+/ {
+	model = "NXP i.MX93 11X11 EVK board";
+	compatible = "fsl,imx93-11x11-evk", "fsl,imx93";
+
+	chosen {
+		stdout-path = &lpuart1;
+	};
+
+	reg_usdhc2_vmmc: regulator-usdhc2 {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>;
+		regulator-name = "VSD_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio3 7 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+};
+
+&mu1 {
+	status = "okay";
+};
+
+&mu2 {
+	status = "okay";
+};
+
+&lpuart1 { /* console */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&usdhc1 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc1>;
+	pinctrl-1 = <&pinctrl_usdhc1>;
+	pinctrl-2 = <&pinctrl_usdhc1>;
+	bus-width = <8>;
+	non-removable;
+	status = "okay";
+};
+
+&usdhc2 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
+	pinctrl-1 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
+	pinctrl-2 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
+	cd-gpios = <&gpio3 00 GPIO_ACTIVE_LOW>;
+	vmmc-supply = <&reg_usdhc2_vmmc>;
+	bus-width = <4>;
+	status = "okay";
+	no-sdio;
+	no-mmc;
+};
+
+&iomuxc {
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX93_PAD_UART1_RXD__LPUART1_RX			0x31e
+			MX93_PAD_UART1_TXD__LPUART1_TX			0x31e
+		>;
+	};
+
+	pinctrl_usdhc1: usdhc1grp {
+		fsl,pins = <
+			MX93_PAD_SD1_CLK__USDHC1_CLK		0x17fe
+			MX93_PAD_SD1_CMD__USDHC1_CMD		0x13fe
+			MX93_PAD_SD1_DATA0__USDHC1_DATA0	0x13fe
+			MX93_PAD_SD1_DATA1__USDHC1_DATA1	0x13fe
+			MX93_PAD_SD1_DATA2__USDHC1_DATA2	0x13fe
+			MX93_PAD_SD1_DATA3__USDHC1_DATA3	0x13fe
+			MX93_PAD_SD1_DATA4__USDHC1_DATA4	0x13fe
+			MX93_PAD_SD1_DATA5__USDHC1_DATA5	0x13fe
+			MX93_PAD_SD1_DATA6__USDHC1_DATA6	0x13fe
+			MX93_PAD_SD1_DATA7__USDHC1_DATA7	0x13fe
+			MX93_PAD_SD1_STROBE__USDHC1_STROBE	0x17fe
+		>;
+	};
+
+	pinctrl_reg_usdhc2_vmmc: regusdhc2vmmcgrp {
+		fsl,pins = <
+			MX93_PAD_SD2_RESET_B__GPIO3_IO07	0x31e
+		>;
+	};
+
+	pinctrl_usdhc2_gpio: usdhc2gpiogrp {
+		fsl,pins = <
+			MX93_PAD_SD2_CD_B__GPIO3_IO00		0x31e
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX93_PAD_SD2_CLK__USDHC2_CLK		0x17fe
+			MX93_PAD_SD2_CMD__USDHC2_CMD		0x13fe
+			MX93_PAD_SD2_DATA0__USDHC2_DATA0	0x13fe
+			MX93_PAD_SD2_DATA1__USDHC2_DATA1	0x13fe
+			MX93_PAD_SD2_DATA2__USDHC2_DATA2	0x13fe
+			MX93_PAD_SD2_DATA3__USDHC2_DATA3	0x13fe
+			MX93_PAD_SD2_VSELECT__USDHC2_VSELECT	0x51e
+		>;
+	};
+};
diff --git a/arch/arm64/boot/dts/freescale/imx93-pinfunc.h b/arch/arm64/boot/dts/freescale/imx93-pinfunc.h
new file mode 100755
index 000000000000..4298a145f8a9
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx93-pinfunc.h
@@ -0,0 +1,623 @@
+/* SPDX-License-Identifier: (GPL-2.0+ OR MIT) */
+/*
+ * Copyright 2022 NXP
+ */
+
+#ifndef __DTS_IMX93_PINFUNC_H
+#define __DTS_IMX93_PINFUNC_H
+
+/*
+ * The pin function ID is a tuple of
+ * <mux_reg conf_reg input_reg mux_mode input_val>
+ */
+#define MX93_PAD_DAP_TDI__JTAG_MUX_TDI                            0x0000 0x01B0 0x03D8 0x0 0x0
+#define MX93_PAD_DAP_TDI__MQS2_LEFT                               0x0000 0x01B0 0x0000 0x1 0x0
+#define MX93_PAD_DAP_TDI__CAN2_TX                                 0x0000 0x01B0 0x0000 0x3 0x0
+#define MX93_PAD_DAP_TDI__FLEXIO2_FLEXIO30                        0x0000 0x01B0 0x0000 0x4 0x0
+#define MX93_PAD_DAP_TDI__GPIO3_IO28                              0x0000 0x01B0 0x0000 0x5 0x0
+#define MX93_PAD_DAP_TDI__LPUART5_RX                              0x0000 0x01B0 0x0430 0x6 0x0
+#define MX93_PAD_DAP_TMS_SWDIO__JTAG_MUX_TMS                      0x0004 0x01B4 0x03DC 0x0 0x0
+#define MX93_PAD_DAP_TMS_SWDIO__FLEXIO2_FLEXIO31                  0x0004 0x01B4 0x0000 0x4 0x0
+#define MX93_PAD_DAP_TMS_SWDIO__GPIO3_IO29                        0x0004 0x01B4 0x0000 0x5 0x0
+#define MX93_PAD_DAP_TMS_SWDIO__LPUART5_RTS_B                     0x0004 0x01B4 0x0000 0x6 0x0
+#define MX93_PAD_DAP_TCLK_SWCLK__JTAG_MUX_TCK                     0x0008 0x01B8 0x03D4 0x0 0x0
+#define MX93_PAD_DAP_TCLK_SWCLK__FLEXIO1_FLEXIO30                 0x0008 0x01B8 0x0000 0x4 0x0
+#define MX93_PAD_DAP_TCLK_SWCLK__GPIO3_IO30                       0x0008 0x01B8 0x0000 0x5 0x0
+#define MX93_PAD_DAP_TCLK_SWCLK__LPUART5_CTS_B                    0x0008 0x01B8 0x042C 0x6 0x0
+#define MX93_PAD_DAP_TDO_TRACESWO__JTAG_MUX_TDO                   0x000C 0x01BC 0x0000 0x0 0x0
+#define MX93_PAD_DAP_TDO_TRACESWO__MQS2_RIGHT                     0x000C 0x01BC 0x0000 0x1 0x0
+#define MX93_PAD_DAP_TDO_TRACESWO__CAN2_RX                        0x000C 0x01BC 0x0364 0x3 0x0
+#define MX93_PAD_DAP_TDO_TRACESWO__FLEXIO1_FLEXIO31               0x000C 0x01BC 0x0000 0x4 0x0
+#define MX93_PAD_DAP_TDO_TRACESWO__GPIO3_IO31                     0x000C 0x01BC 0x0000 0x5 0x0
+#define MX93_PAD_DAP_TDO_TRACESWO__LPUART5_TX                     0x000C 0x01BC 0x0434 0x6 0x0
+#define MX93_PAD_GPIO_IO00__GPIO2_IO00                            0x0010 0x01C0 0x0000 0x0 0x0
+#define MX93_PAD_GPIO_IO00__LPI2C3_SDA                            0x0010 0x01C0 0x03E4 0x11 0x0
+#define MX93_PAD_GPIO_IO00__MEDIAMIX_CAM_CLK                      0x0010 0x01C0 0x0000 0x2 0x0
+#define MX93_PAD_GPIO_IO00__MEDIAMIX_DISP_CLK                     0x0010 0x01C0 0x0000 0x3 0x0
+#define MX93_PAD_GPIO_IO00__LPSPI6_PCS0                           0x0010 0x01C0 0x0000 0x4 0x0
+#define MX93_PAD_GPIO_IO00__LPUART5_TX                            0x0010 0x01C0 0x0434 0x5 0x1
+#define MX93_PAD_GPIO_IO00__LPI2C5_SDA                            0x0010 0x01C0 0x03EC 0x16 0x0
+#define MX93_PAD_GPIO_IO00__FLEXIO1_FLEXIO00                      0x0010 0x01C0 0x036C 0x7 0x0
+#define MX93_PAD_GPIO_IO01__GPIO2_IO01                            0x0014 0x01C4 0x0000 0x0 0x0
+#define MX93_PAD_GPIO_IO01__LPI2C3_SCL                            0x0014 0x01C4 0x03E0 0x11 0x0
+#define MX93_PAD_GPIO_IO01__MEDIAMIX_CAM_DATA00                   0x0014 0x01C4 0x0000 0x2 0x0
+#define MX93_PAD_GPIO_IO01__MEDIAMIX_DISP_DE                      0x0014 0x01C4 0x0000 0x3 0x0
+#define MX93_PAD_GPIO_IO01__LPSPI6_SIN                            0x0014 0x01C4 0x0000 0x4 0x0
+#define MX93_PAD_GPIO_IO01__LPUART5_RX                            0x0014 0x01C4 0x0430 0x5 0x1
+#define MX93_PAD_GPIO_IO01__LPI2C5_SCL                            0x0014 0x01C4 0x03E8 0x16 0x0
+#define MX93_PAD_GPIO_IO01__FLEXIO1_FLEXIO01                      0x0014 0x01C4 0x0370 0x7 0x0
+#define MX93_PAD_GPIO_IO02__GPIO2_IO02                            0x0018 0x01C8 0x0000 0x0 0x0
+#define MX93_PAD_GPIO_IO02__LPI2C4_SDA                            0x0018 0x01C8 0x0000 0x11 0x0
+#define MX93_PAD_GPIO_IO02__MEDIAMIX_CAM_VSYNC                    0x0018 0x01C8 0x0000 0x2 0x0
+#define MX93_PAD_GPIO_IO02__MEDIAMIX_DISP_VSYNC                   0x0018 0x01C8 0x0000 0x3 0x0
+#define MX93_PAD_GPIO_IO02__LPSPI6_SOUT                           0x0018 0x01C8 0x0000 0x4 0x0
+#define MX93_PAD_GPIO_IO02__LPUART5_CTS_B                         0x0018 0x01C8 0x042C 0x5 0x1
+#define MX93_PAD_GPIO_IO02__LPI2C6_SDA                            0x0018 0x01C8 0x03F4 0x16 0x0
+#define MX93_PAD_GPIO_IO02__FLEXIO1_FLEXIO02                      0x0018 0x01C8 0x0374 0x7 0x0
+#define MX93_PAD_GPIO_IO03__GPIO2_IO03                            0x001C 0x01CC 0x0000 0x0 0x0
+#define MX93_PAD_GPIO_IO03__LPI2C4_SCL                            0x001C 0x01CC 0x0000 0x11 0x0
+#define MX93_PAD_GPIO_IO03__MEDIAMIX_CAM_HSYNC                    0x001C 0x01CC 0x0000 0x2 0x0
+#define MX93_PAD_GPIO_IO03__MEDIAMIX_DISP_HSYNC                   0x001C 0x01CC 0x0000 0x3 0x0
+#define MX93_PAD_GPIO_IO03__LPSPI6_SCK                            0x001C 0x01CC 0x0000 0x4 0x0
+#define MX93_PAD_GPIO_IO03__LPUART5_RTS_B                         0x001C 0x01CC 0x0000 0x5 0x0
+#define MX93_PAD_GPIO_IO03__LPI2C6_SCL                            0x001C 0x01CC 0x03F0 0x16 0x0
+#define MX93_PAD_GPIO_IO03__FLEXIO1_FLEXIO03                      0x001C 0x01CC 0x0378 0x7 0x0
+#define MX93_PAD_GPIO_IO04__GPIO2_IO04                            0x0020 0x01D0 0x0000 0x0 0x0
+#define MX93_PAD_GPIO_IO04__TPM3_CH0                              0x0020 0x01D0 0x0000 0x1 0x0
+#define MX93_PAD_GPIO_IO04__PDM_CLK                               0x0020 0x01D0 0x0000 0x2 0x0
+#define MX93_PAD_GPIO_IO04__MEDIAMIX_DISP_DATA00                  0x0020 0x01D0 0x0000 0x3 0x0
+#define MX93_PAD_GPIO_IO04__LPSPI7_PCS0                           0x0020 0x01D0 0x0000 0x4 0x0
+#define MX93_PAD_GPIO_IO04__LPUART6_TX                            0x0020 0x01D0 0x0000 0x5 0x0
+#define MX93_PAD_GPIO_IO04__LPI2C6_SDA                            0x0020 0x01D0 0x03F4 0x16 0x1
+#define MX93_PAD_GPIO_IO04__FLEXIO1_FLEXIO04                      0x0020 0x01D0 0x037C 0x7 0x0
+#define MX93_PAD_GPIO_IO05__GPIO2_IO05                            0x0024 0x01D4 0x0000 0x0 0x0
+#define MX93_PAD_GPIO_IO05__TPM4_CH0                              0x0024 0x01D4 0x0000 0x1 0x0
+#define MX93_PAD_GPIO_IO05__PDM_BIT_STREAM00                      0x0024 0x01D4 0x0438 0x2 0x0
+#define MX93_PAD_GPIO_IO05__MEDIAMIX_DISP_DATA01                  0x0024 0x01D4 0x0000 0x3 0x0
+#define MX93_PAD_GPIO_IO05__LPSPI7_SIN                            0x0024 0x01D4 0x0000 0x4 0x0
+#define MX93_PAD_GPIO_IO05__LPUART6_RX                            0x0024 0x01D4 0x0000 0x5 0x0
+#define MX93_PAD_GPIO_IO05__LPI2C6_SCL                            0x0024 0x01D4 0x03F0 0x16 0x1
+#define MX93_PAD_GPIO_IO05__FLEXIO1_FLEXIO05                      0x0024 0x01D4 0x0380 0x7 0x0
+#define MX93_PAD_GPIO_IO06__GPIO2_IO06                            0x0028 0x01D8 0x0000 0x0 0x0
+#define MX93_PAD_GPIO_IO06__TPM5_CH0                              0x0028 0x01D8 0x0000 0x1 0x0
+#define MX93_PAD_GPIO_IO06__PDM_BIT_STREAM01                      0x0028 0x01D8 0x043C 0x2 0x0
+#define MX93_PAD_GPIO_IO06__MEDIAMIX_DISP_DATA02                  0x0028 0x01D8 0x0000 0x3 0x0
+#define MX93_PAD_GPIO_IO06__LPSPI7_SOUT                           0x0028 0x01D8 0x0000 0x4 0x0
+#define MX93_PAD_GPIO_IO06__LPUART6_CTS_B                         0x0028 0x01D8 0x0000 0x5 0x0
+#define MX93_PAD_GPIO_IO06__LPI2C7_SDA                            0x0028 0x01D8 0x03FC 0x16 0x0
+#define MX93_PAD_GPIO_IO06__FLEXIO1_FLEXIO06                      0x0028 0x01D8 0x0384 0x7 0x0
+#define MX93_PAD_GPIO_IO07__GPIO2_IO07                            0x002C 0x01DC 0x0000 0x0 0x0
+#define MX93_PAD_GPIO_IO07__LPSPI3_PCS1                           0x002C 0x01DC 0x0000 0x1 0x0
+#define MX93_PAD_GPIO_IO07__MEDIAMIX_CAM_DATA01                   0x002C 0x01DC 0x0000 0x2 0x0
+#define MX93_PAD_GPIO_IO07__MEDIAMIX_DISP_DATA03                  0x002C 0x01DC 0x0000 0x3 0x0
+#define MX93_PAD_GPIO_IO07__LPSPI7_SCK                            0x002C 0x01DC 0x0000 0x4 0x0
+#define MX93_PAD_GPIO_IO07__LPUART6_RTS_B                         0x002C 0x01DC 0x0000 0x5 0x0
+#define MX93_PAD_GPIO_IO07__LPI2C7_SCL                            0x002C 0x01DC 0x03F8 0x16 0x0
+#define MX93_PAD_GPIO_IO07__FLEXIO1_FLEXIO07                      0x002C 0x01DC 0x0388 0x7 0x0
+#define MX93_PAD_GPIO_IO08__GPIO2_IO08                            0x0030 0x01E0 0x0000 0x0 0x0
+#define MX93_PAD_GPIO_IO08__LPSPI3_PCS0                           0x0030 0x01E0 0x0000 0x1 0x0
+#define MX93_PAD_GPIO_IO08__MEDIAMIX_CAM_DATA02                   0x0030 0x01E0 0x0000 0x2 0x0
+#define MX93_PAD_GPIO_IO08__MEDIAMIX_DISP_DATA04                  0x0030 0x01E0 0x0000 0x3 0x0
+#define MX93_PAD_GPIO_IO08__TPM6_CH0                              0x0030 0x01E0 0x0000 0x4 0x0
+#define MX93_PAD_GPIO_IO08__LPUART7_TX                            0x0030 0x01E0 0x0000 0x5 0x0
+#define MX93_PAD_GPIO_IO08__LPI2C7_SDA                            0x0030 0x01E0 0x03FC 0x16 0x1
+#define MX93_PAD_GPIO_IO08__FLEXIO1_FLEXIO08                      0x0030 0x01E0 0x038C 0x7 0x0
+#define MX93_PAD_GPIO_IO09__GPIO2_IO09                            0x0034 0x01E4 0x0000 0x0 0x0
+#define MX93_PAD_GPIO_IO09__LPSPI3_SIN                            0x0034 0x01E4 0x0000 0x1 0x0
+#define MX93_PAD_GPIO_IO09__MEDIAMIX_CAM_DATA03                   0x0034 0x01E4 0x0000 0x2 0x0
+#define MX93_PAD_GPIO_IO09__MEDIAMIX_DISP_DATA05                  0x0034 0x01E4 0x0000 0x3 0x0
+#define MX93_PAD_GPIO_IO09__TPM3_EXTCLK                           0x0034 0x01E4 0x0000 0x4 0x0
+#define MX93_PAD_GPIO_IO09__LPUART7_RX                            0x0034 0x01E4 0x0000 0x5 0x0
+#define MX93_PAD_GPIO_IO09__LPI2C7_SCL                            0x0034 0x01E4 0x03F8 0x16 0x1
+#define MX93_PAD_GPIO_IO09__FLEXIO1_FLEXIO09                      0x0034 0x01E4 0x0390 0x7 0x0
+#define MX93_PAD_GPIO_IO10__GPIO2_IO10                            0x0038 0x01E8 0x0000 0x0 0x0
+#define MX93_PAD_GPIO_IO10__LPSPI3_SOUT                           0x0038 0x01E8 0x0000 0x1 0x0
+#define MX93_PAD_GPIO_IO10__MEDIAMIX_CAM_DATA04                   0x0038 0x01E8 0x0000 0x2 0x0
+#define MX93_PAD_GPIO_IO10__MEDIAMIX_DISP_DATA06                  0x0038 0x01E8 0x0000 0x3 0x0
+#define MX93_PAD_GPIO_IO10__TPM4_EXTCLK                           0x0038 0x01E8 0x0000 0x4 0x0
+#define MX93_PAD_GPIO_IO10__LPUART7_CTS_B                         0x0038 0x01E8 0x0000 0x5 0x0
+#define MX93_PAD_GPIO_IO10__LPI2C8_SDA                            0x0038 0x01E8 0x0404 0x16 0x0
+#define MX93_PAD_GPIO_IO10__FLEXIO1_FLEXIO10                      0x0038 0x01E8 0x0394 0x7 0x0
+#define MX93_PAD_GPIO_IO11__GPIO2_IO11                            0x003C 0x01EC 0x0000 0x0 0x0
+#define MX93_PAD_GPIO_IO11__LPSPI3_SCK                            0x003C 0x01EC 0x0000 0x1 0x0
+#define MX93_PAD_GPIO_IO11__MEDIAMIX_CAM_DATA05                   0x003C 0x01EC 0x0000 0x2 0x0
+#define MX93_PAD_GPIO_IO11__MEDIAMIX_DISP_DATA07                  0x003C 0x01EC 0x0000 0x3 0x0
+#define MX93_PAD_GPIO_IO11__TPM5_EXTCLK                           0x003C 0x01EC 0x0000 0x4 0x0
+#define MX93_PAD_GPIO_IO11__LPUART7_RTS_B                         0x003C 0x01EC 0x0000 0x5 0x0
+#define MX93_PAD_GPIO_IO11__LPI2C8_SCL                            0x003C 0x01EC 0x0400 0x16 0x0
+#define MX93_PAD_GPIO_IO11__FLEXIO1_FLEXIO11                      0x003C 0x01EC 0x0398 0x7 0x0
+#define MX93_PAD_GPIO_IO12__GPIO2_IO12                            0x0040 0x01F0 0x0000 0x0 0x0
+#define MX93_PAD_GPIO_IO12__TPM3_CH2                              0x0040 0x01F0 0x0000 0x1 0x0
+#define MX93_PAD_GPIO_IO12__PDM_BIT_STREAM02                      0x0040 0x01F0 0x0440 0x2 0x0
+#define MX93_PAD_GPIO_IO12__MEDIAMIX_DISP_DATA08                  0x0040 0x01F0 0x0000 0x3 0x0
+#define MX93_PAD_GPIO_IO12__LPSPI8_PCS0                           0x0040 0x01F0 0x0000 0x4 0x0
+#define MX93_PAD_GPIO_IO12__LPUART8_TX                            0x0040 0x01F0 0x0000 0x5 0x0
+#define MX93_PAD_GPIO_IO12__LPI2C8_SDA                            0x0040 0x01F0 0x0404 0x16 0x1
+#define MX93_PAD_GPIO_IO12__SAI3_RX_SYNC                          0x0040 0x01F0 0x0450 0x7 0x0
+#define MX93_PAD_GPIO_IO13__GPIO2_IO13                            0x0044 0x01F4 0x0000 0x0 0x0
+#define MX93_PAD_GPIO_IO13__TPM4_CH2                              0x0044 0x01F4 0x0000 0x1 0x0
+#define MX93_PAD_GPIO_IO13__PDM_BIT_STREAM03                      0x0044 0x01F4 0x0444 0x2 0x0
+#define MX93_PAD_GPIO_IO13__MEDIAMIX_DISP_DATA09                  0x0044 0x01F4 0x0000 0x3 0x0
+#define MX93_PAD_GPIO_IO13__LPSPI8_SIN                            0x0044 0x01F4 0x0000 0x4 0x0
+#define MX93_PAD_GPIO_IO13__LPUART8_RX                            0x0044 0x01F4 0x0000 0x5 0x0
+#define MX93_PAD_GPIO_IO13__LPI2C8_SCL                            0x0044 0x01F4 0x0400 0x16 0x1
+#define MX93_PAD_GPIO_IO13__FLEXIO1_FLEXIO13                      0x0044 0x01F4 0x039C 0x7 0x0
+#define MX93_PAD_GPIO_IO14__GPIO2_IO14                            0x0048 0x01F8 0x0000 0x0 0x0
+#define MX93_PAD_GPIO_IO14__LPUART3_TX                            0x0048 0x01F8 0x041C 0x1 0x0
+#define MX93_PAD_GPIO_IO14__MEDIAMIX_CAM_DATA06                   0x0048 0x01F8 0x0000 0x2 0x0
+#define MX93_PAD_GPIO_IO14__MEDIAMIX_DISP_DATA10                  0x0048 0x01F8 0x0000 0x3 0x0
+#define MX93_PAD_GPIO_IO14__LPSPI8_SOUT                           0x0048 0x01F8 0x0000 0x4 0x0
+#define MX93_PAD_GPIO_IO14__LPUART8_CTS_B                         0x0048 0x01F8 0x0000 0x5 0x0
+#define MX93_PAD_GPIO_IO14__LPUART4_TX                            0x0048 0x01F8 0x0428 0x6 0x0
+#define MX93_PAD_GPIO_IO14__FLEXIO1_FLEXIO14                      0x0048 0x01F8 0x03A0 0x7 0x0
+#define MX93_PAD_GPIO_IO15__GPIO2_IO15                            0x004C 0x01FC 0x0000 0x0 0x0
+#define MX93_PAD_GPIO_IO15__LPUART3_RX                            0x004C 0x01FC 0x0418 0x1 0x0
+#define MX93_PAD_GPIO_IO15__MEDIAMIX_CAM_DATA07                   0x004C 0x01FC 0x0000 0x2 0x0
+#define MX93_PAD_GPIO_IO15__MEDIAMIX_DISP_DATA11                  0x004C 0x01FC 0x0000 0x3 0x0
+#define MX93_PAD_GPIO_IO15__LPSPI8_SCK                            0x004C 0x01FC 0x0000 0x4 0x0
+#define MX93_PAD_GPIO_IO15__LPUART8_RTS_B                         0x004C 0x01FC 0x0000 0x5 0x0
+#define MX93_PAD_GPIO_IO15__LPUART4_RX                            0x004C 0x01FC 0x0424 0x6 0x0
+#define MX93_PAD_GPIO_IO15__FLEXIO1_FLEXIO15                      0x004C 0x01FC 0x03A4 0x7 0x0
+#define MX93_PAD_GPIO_IO16__GPIO2_IO16                            0x0050 0x0200 0x0000 0x0 0x0
+#define MX93_PAD_GPIO_IO16__SAI3_TX_BCLK                          0x0050 0x0200 0x0000 0x1 0x0
+#define MX93_PAD_GPIO_IO16__PDM_BIT_STREAM02                      0x0050 0x0200 0x0440 0x2 0x1
+#define MX93_PAD_GPIO_IO16__MEDIAMIX_DISP_DATA12                  0x0050 0x0200 0x0000 0x3 0x0
+#define MX93_PAD_GPIO_IO16__LPUART3_CTS_B                         0x0050 0x0200 0x0414 0x4 0x0
+#define MX93_PAD_GPIO_IO16__LPSPI4_PCS2                           0x0050 0x0200 0x0000 0x5 0x0
+#define MX93_PAD_GPIO_IO16__LPUART4_CTS_B                         0x0050 0x0200 0x0420 0x6 0x0
+#define MX93_PAD_GPIO_IO16__FLEXIO1_FLEXIO16                      0x0050 0x0200 0x03A8 0x7 0x0
+#define MX93_PAD_GPIO_IO17__GPIO2_IO17                            0x0054 0x0204 0x0000 0x0 0x0
+#define MX93_PAD_GPIO_IO17__SAI3_MCLK                             0x0054 0x0204 0x0000 0x1 0x0
+#define MX93_PAD_GPIO_IO17__MEDIAMIX_CAM_DATA08                   0x0054 0x0204 0x0000 0x2 0x0
+#define MX93_PAD_GPIO_IO17__MEDIAMIX_DISP_DATA13                  0x0054 0x0204 0x0000 0x3 0x0
+#define MX93_PAD_GPIO_IO17__LPUART3_RTS_B                         0x0054 0x0204 0x0000 0x4 0x0
+#define MX93_PAD_GPIO_IO17__LPSPI4_PCS1                           0x0054 0x0204 0x0000 0x5 0x0
+#define MX93_PAD_GPIO_IO17__LPUART4_RTS_B                         0x0054 0x0204 0x0000 0x6 0x0
+#define MX93_PAD_GPIO_IO17__FLEXIO1_FLEXIO17                      0x0054 0x0204 0x03AC 0x7 0x0
+#define MX93_PAD_GPIO_IO18__GPIO2_IO18                            0x0058 0x0208 0x0000 0x0 0x0
+#define MX93_PAD_GPIO_IO18__SAI3_RX_BCLK                          0x0058 0x0208 0x044C 0x1 0x0
+#define MX93_PAD_GPIO_IO18__MEDIAMIX_CAM_DATA09                   0x0058 0x0208 0x0000 0x2 0x0
+#define MX93_PAD_GPIO_IO18__MEDIAMIX_DISP_DATA14                  0x0058 0x0208 0x0000 0x3 0x0
+#define MX93_PAD_GPIO_IO18__LPSPI5_PCS0                           0x0058 0x0208 0x0000 0x4 0x0
+#define MX93_PAD_GPIO_IO18__LPSPI4_PCS0                           0x0058 0x0208 0x0000 0x5 0x0
+#define MX93_PAD_GPIO_IO18__TPM5_CH2                              0x0058 0x0208 0x0000 0x6 0x0
+#define MX93_PAD_GPIO_IO18__FLEXIO1_FLEXIO18                      0x0058 0x0208 0x03B0 0x7 0x0
+#define MX93_PAD_GPIO_IO19__GPIO2_IO19                            0x005C 0x020C 0x0000 0x0 0x0
+#define MX93_PAD_GPIO_IO19__SAI3_RX_SYNC                          0x005C 0x020C 0x0450 0x1 0x1
+#define MX93_PAD_GPIO_IO19__PDM_BIT_STREAM03                      0x005C 0x020C 0x0444 0x2 0x1
+#define MX93_PAD_GPIO_IO19__MEDIAMIX_DISP_DATA15                  0x005C 0x020C 0x0000 0x3 0x0
+#define MX93_PAD_GPIO_IO19__LPSPI5_SIN                            0x005C 0x020C 0x0000 0x4 0x0
+#define MX93_PAD_GPIO_IO19__LPSPI4_SIN                            0x005C 0x020C 0x0000 0x5 0x0
+#define MX93_PAD_GPIO_IO19__TPM6_CH2                              0x005C 0x020C 0x0000 0x6 0x0
+#define MX93_PAD_GPIO_IO19__SAI3_TX_DATA00                        0x005C 0x020C 0x0000 0x7 0x0
+#define MX93_PAD_GPIO_IO20__GPIO2_IO20                            0x0060 0x0210 0x0000 0x0 0x0
+#define MX93_PAD_GPIO_IO20__SAI3_RX_DATA00                        0x0060 0x0210 0x0000 0x1 0x0
+#define MX93_PAD_GPIO_IO20__PDM_BIT_STREAM00                      0x0060 0x0210 0x0438 0x2 0x1
+#define MX93_PAD_GPIO_IO20__MEDIAMIX_DISP_DATA16                  0x0060 0x0210 0x0000 0x3 0x0
+#define MX93_PAD_GPIO_IO20__LPSPI5_SOUT                           0x0060 0x0210 0x0000 0x4 0x0
+#define MX93_PAD_GPIO_IO20__LPSPI4_SOUT                           0x0060 0x0210 0x0000 0x5 0x0
+#define MX93_PAD_GPIO_IO20__TPM3_CH1                              0x0060 0x0210 0x0000 0x6 0x0
+#define MX93_PAD_GPIO_IO20__FLEXIO1_FLEXIO20                      0x0060 0x0210 0x03B4 0x7 0x0
+#define MX93_PAD_GPIO_IO21__GPIO2_IO21                            0x0064 0x0214 0x0000 0x0 0x0
+#define MX93_PAD_GPIO_IO21__SAI3_TX_DATA00                        0x0064 0x0214 0x0000 0x1 0x0
+#define MX93_PAD_GPIO_IO21__PDM_CLK                               0x0064 0x0214 0x0000 0x2 0x0
+#define MX93_PAD_GPIO_IO21__MEDIAMIX_DISP_DATA17                  0x0064 0x0214 0x0000 0x3 0x0
+#define MX93_PAD_GPIO_IO21__LPSPI5_SCK                            0x0064 0x0214 0x0000 0x4 0x0
+#define MX93_PAD_GPIO_IO21__LPSPI4_SCK                            0x0064 0x0214 0x0000 0x5 0x0
+#define MX93_PAD_GPIO_IO21__TPM4_CH1                              0x0064 0x0214 0x0000 0x6 0x0
+#define MX93_PAD_GPIO_IO21__SAI3_RX_BCLK                          0x0064 0x0214 0x044C 0x7 0x1
+#define MX93_PAD_GPIO_IO22__GPIO2_IO22                            0x0068 0x0218 0x0000 0x0 0x0
+#define MX93_PAD_GPIO_IO22__USDHC3_CLK                            0x0068 0x0218 0x0458 0x1 0x0
+#define MX93_PAD_GPIO_IO22__SPDIF_IN                              0x0068 0x0218 0x0454 0x2 0x0
+#define MX93_PAD_GPIO_IO22__MEDIAMIX_DISP_DATA18                  0x0068 0x0218 0x0000 0x3 0x0
+#define MX93_PAD_GPIO_IO22__TPM5_CH1                              0x0068 0x0218 0x0000 0x4 0x0
+#define MX93_PAD_GPIO_IO22__TPM6_EXTCLK                           0x0068 0x0218 0x0000 0x5 0x0
+#define MX93_PAD_GPIO_IO22__LPI2C5_SDA                            0x0068 0x0218 0x03EC 0x16 0x1
+#define MX93_PAD_GPIO_IO22__FLEXIO1_FLEXIO22                      0x0068 0x0218 0x03B8 0x7 0x0
+#define MX93_PAD_GPIO_IO23__GPIO2_IO23                            0x006C 0x021C 0x0000 0x0 0x0
+#define MX93_PAD_GPIO_IO23__USDHC3_CMD                            0x006C 0x021C 0x045C 0x1 0x0
+#define MX93_PAD_GPIO_IO23__SPDIF_OUT                             0x006C 0x021C 0x0000 0x2 0x0
+#define MX93_PAD_GPIO_IO23__MEDIAMIX_DISP_DATA19                  0x006C 0x021C 0x0000 0x3 0x0
+#define MX93_PAD_GPIO_IO23__TPM6_CH1                              0x006C 0x021C 0x0000 0x4 0x0
+#define MX93_PAD_GPIO_IO23__LPI2C5_SCL                            0x006C 0x021C 0x03E8 0x16 0x1
+#define MX93_PAD_GPIO_IO23__FLEXIO1_FLEXIO23                      0x006C 0x021C 0x03BC 0x7 0x0
+#define MX93_PAD_GPIO_IO24__GPIO2_IO24                            0x0070 0x0220 0x0000 0x0 0x0
+#define MX93_PAD_GPIO_IO24__USDHC3_DATA0                          0x0070 0x0220 0x0460 0x1 0x0
+#define MX93_PAD_GPIO_IO24__MEDIAMIX_DISP_DATA20                  0x0070 0x0220 0x0000 0x3 0x0
+#define MX93_PAD_GPIO_IO24__TPM3_CH3                              0x0070 0x0220 0x0000 0x4 0x0
+#define MX93_PAD_GPIO_IO24__JTAG_MUX_TDO                          0x0070 0x0220 0x0000 0x5 0x0
+#define MX93_PAD_GPIO_IO24__LPSPI6_PCS1                           0x0070 0x0220 0x0000 0x6 0x0
+#define MX93_PAD_GPIO_IO24__FLEXIO1_FLEXIO24                      0x0070 0x0220 0x03C0 0x7 0x0
+#define MX93_PAD_GPIO_IO25__GPIO2_IO25                            0x0074 0x0224 0x0000 0x0 0x0
+#define MX93_PAD_GPIO_IO25__USDHC3_DATA1                          0x0074 0x0224 0x0464 0x1 0x0
+#define MX93_PAD_GPIO_IO25__CAN2_TX                               0x0074 0x0224 0x0000 0x2 0x0
+#define MX93_PAD_GPIO_IO25__MEDIAMIX_DISP_DATA21                  0x0074 0x0224 0x0000 0x3 0x0
+#define MX93_PAD_GPIO_IO25__TPM4_CH3                              0x0074 0x0224 0x0000 0x4 0x0
+#define MX93_PAD_GPIO_IO25__JTAG_MUX_TCK                          0x0074 0x0224 0x03D4 0x5 0x1
+#define MX93_PAD_GPIO_IO25__LPSPI7_PCS1                           0x0074 0x0224 0x0000 0x6 0x0
+#define MX93_PAD_GPIO_IO25__FLEXIO1_FLEXIO25                      0x0074 0x0224 0x03C4 0x7 0x0
+#define MX93_PAD_GPIO_IO26__GPIO2_IO26                            0x0078 0x0228 0x0000 0x0 0x0
+#define MX93_PAD_GPIO_IO26__USDHC3_DATA2                          0x0078 0x0228 0x0468 0x1 0x0
+#define MX93_PAD_GPIO_IO26__PDM_BIT_STREAM01                      0x0078 0x0228 0x043C 0x2 0x1
+#define MX93_PAD_GPIO_IO26__MEDIAMIX_DISP_DATA22                  0x0078 0x0228 0x0000 0x3 0x0
+#define MX93_PAD_GPIO_IO26__TPM5_CH3                              0x0078 0x0228 0x0000 0x4 0x0
+#define MX93_PAD_GPIO_IO26__JTAG_MUX_TDI                          0x0078 0x0228 0x03D8 0x5 0x1
+#define MX93_PAD_GPIO_IO26__LPSPI8_PCS1                           0x0078 0x0228 0x0000 0x6 0x0
+#define MX93_PAD_GPIO_IO26__SAI3_TX_SYNC                          0x0078 0x0228 0x0000 0x7 0x0
+#define MX93_PAD_GPIO_IO27__GPIO2_IO27                            0x007C 0x022C 0x0000 0x0 0x0
+#define MX93_PAD_GPIO_IO27__USDHC3_DATA3                          0x007C 0x022C 0x046C 0x1 0x0
+#define MX93_PAD_GPIO_IO27__CAN2_RX                               0x007C 0x022C 0x0364 0x2 0x1
+#define MX93_PAD_GPIO_IO27__MEDIAMIX_DISP_DATA23                  0x007C 0x022C 0x0000 0x3 0x0
+#define MX93_PAD_GPIO_IO27__TPM6_CH3                              0x007C 0x022C 0x0000 0x4 0x0
+#define MX93_PAD_GPIO_IO27__JTAG_MUX_TMS                          0x007C 0x022C 0x03DC 0x5 0x1
+#define MX93_PAD_GPIO_IO27__LPSPI5_PCS1                           0x007C 0x022C 0x0000 0x6 0x0
+#define MX93_PAD_GPIO_IO27__FLEXIO1_FLEXIO27                      0x007C 0x022C 0x03C8 0x7 0x0
+#define MX93_PAD_GPIO_IO28__GPIO2_IO28                            0x0080 0x0230 0x0000 0x0 0x0
+#define MX93_PAD_GPIO_IO28__LPI2C3_SDA                            0x0080 0x0230 0x03E4 0x11 0x1
+#define MX93_PAD_GPIO_IO28__FLEXIO1_FLEXIO28                      0x0080 0x0230 0x0000 0x7 0x0
+#define MX93_PAD_GPIO_IO29__GPIO2_IO29                            0x0084 0x0234 0x0000 0x0 0x0
+#define MX93_PAD_GPIO_IO29__LPI2C3_SCL                            0x0084 0x0234 0x03E0 0x11 0x1
+#define MX93_PAD_GPIO_IO29__FLEXIO1_FLEXIO29                      0x0084 0x0234 0x0000 0x7 0x0
+#define MX93_PAD_CCM_CLKO1__CCMSRCGPCMIX_CLKO1                    0x0088 0x0238 0x0000 0x0 0x0
+#define MX93_PAD_CCM_CLKO1__FLEXIO1_FLEXIO26                      0x0088 0x0238 0x0000 0x4 0x0
+#define MX93_PAD_CCM_CLKO1__GPIO3_IO26                            0x0088 0x0238 0x0000 0x5 0x0
+#define MX93_PAD_CCM_CLKO2__GPIO3_IO27                            0x008C 0x023C 0x0000 0x5 0x0
+#define MX93_PAD_CCM_CLKO2__CCMSRCGPCMIX_CLKO2                    0x008C 0x023C 0x0000 0x0 0x0
+#define MX93_PAD_CCM_CLKO2__FLEXIO1_FLEXIO27                      0x008C 0x023C 0x03C8 0x4 0x1
+#define MX93_PAD_CCM_CLKO3__CCMSRCGPCMIX_CLKO3                    0x0090 0x0240 0x0000 0x0 0x0
+#define MX93_PAD_CCM_CLKO3__FLEXIO2_FLEXIO28                      0x0090 0x0240 0x0000 0x4 0x0
+#define MX93_PAD_CCM_CLKO3__GPIO4_IO28                            0x0090 0x0240 0x0000 0x5 0x0
+#define MX93_PAD_CCM_CLKO4__CCMSRCGPCMIX_CLKO4                    0x0094 0x0244 0x0000 0x0 0x0
+#define MX93_PAD_CCM_CLKO4__FLEXIO2_FLEXIO29                      0x0094 0x0244 0x0000 0x4 0x0
+#define MX93_PAD_CCM_CLKO4__GPIO4_IO29                            0x0094 0x0244 0x0000 0x5 0x0
+#define MX93_PAD_ENET1_MDC__ENET_QOS_MDC                          0x0098 0x0248 0x0000 0x0 0x0
+#define MX93_PAD_ENET1_MDC__LPUART3_DCB_B                         0x0098 0x0248 0x0000 0x1 0x0
+#define MX93_PAD_ENET1_MDC__I3C2_SCL                              0x0098 0x0248 0x03CC 0x2 0x0
+#define MX93_PAD_ENET1_MDC__HSIOMIX_OTG_ID1                       0x0098 0x0248 0x0000 0x3 0x0
+#define MX93_PAD_ENET1_MDC__FLEXIO2_FLEXIO00                      0x0098 0x0248 0x0000 0x4 0x0
+#define MX93_PAD_ENET1_MDC__GPIO4_IO00                            0x0098 0x0248 0x0000 0x5 0x0
+#define MX93_PAD_ENET1_MDIO__ENET_QOS_MDIO                        0x009C 0x024C 0x0000 0x0 0x0
+#define MX93_PAD_ENET1_MDIO__LPUART3_RIN_B                        0x009C 0x024C 0x0000 0x1 0x0
+#define MX93_PAD_ENET1_MDIO__I3C2_SDA                             0x009C 0x024C 0x03D0 0x2 0x0
+#define MX93_PAD_ENET1_MDIO__HSIOMIX_OTG_PWR1                     0x009C 0x024C 0x0000 0x3 0x0
+#define MX93_PAD_ENET1_MDIO__FLEXIO2_FLEXIO01                     0x009C 0x024C 0x0000 0x4 0x0
+#define MX93_PAD_ENET1_MDIO__GPIO4_IO01                           0x009C 0x024C 0x0000 0x5 0x0
+#define MX93_PAD_ENET1_TD3__ENET_QOS_RGMII_TD3                    0x00A0 0x0250 0x0000 0x0 0x0
+#define MX93_PAD_ENET1_TD3__CAN2_TX                               0x00A0 0x0250 0x0000 0x2 0x0
+#define MX93_PAD_ENET1_TD3__HSIOMIX_OTG_ID2                       0x00A0 0x0250 0x0000 0x3 0x0
+#define MX93_PAD_ENET1_TD3__FLEXIO2_FLEXIO02                      0x00A0 0x0250 0x0000 0x4 0x0
+#define MX93_PAD_ENET1_TD3__GPIO4_IO02                            0x00A0 0x0250 0x0000 0x5 0x0
+#define MX93_PAD_ENET1_TD2__ENET_QOS_RGMII_TD2                    0x00A4 0x0254 0x0000 0x0 0x0
+#define MX93_PAD_ENET1_TD2__CCM_ENET_QOS_CLOCK_GENERATE_REF_CLK   0x00A4 0x0254 0x0000 0x1 0x0
+#define MX93_PAD_ENET1_TD2__CAN2_RX                               0x00A4 0x0254 0x0364 0x2 0x2
+#define MX93_PAD_ENET1_TD2__HSIOMIX_OTG_OC2                       0x00A4 0x0254 0x0000 0x3 0x0
+#define MX93_PAD_ENET1_TD2__FLEXIO2_FLEXIO03                      0x00A4 0x0254 0x0000 0x4 0x0
+#define MX93_PAD_ENET1_TD2__GPIO4_IO03                            0x00A4 0x0254 0x0000 0x5 0x0
+#define MX93_PAD_ENET1_TD1__ENET_QOS_RGMII_TD1                    0x00A8 0x0258 0x0000 0x0 0x0
+#define MX93_PAD_ENET1_TD1__LPUART3_RTS_B                         0x00A8 0x0258 0x0000 0x1 0x0
+#define MX93_PAD_ENET1_TD1__I3C2_PUR                              0x00A8 0x0258 0x0000 0x2 0x0
+#define MX93_PAD_ENET1_TD1__HSIOMIX_OTG_OC1                       0x00A8 0x0258 0x0000 0x3 0x0
+#define MX93_PAD_ENET1_TD1__FLEXIO2_FLEXIO04                      0x00A8 0x0258 0x0000 0x4 0x0
+#define MX93_PAD_ENET1_TD1__GPIO4_IO04                            0x00A8 0x0258 0x0000 0x5 0x0
+#define MX93_PAD_ENET1_TD1__I3C2_PUR_B                            0x00A8 0x0258 0x0000 0x6 0x0
+#define MX93_PAD_ENET1_TD0__ENET_QOS_RGMII_TD0                    0x00AC 0x025C 0x0000 0x0 0x0
+#define MX93_PAD_ENET1_TD0__LPUART3_TX                            0x00AC 0x025C 0x041C 0x1 0x1
+#define MX93_PAD_ENET1_TD0__FLEXIO2_FLEXIO05                      0x00AC 0x025C 0x0000 0x4 0x0
+#define MX93_PAD_ENET1_TD0__GPIO4_IO05                            0x00AC 0x025C 0x0000 0x5 0x0
+#define MX93_PAD_ENET1_TX_CTL__ENET_QOS_RGMII_TX_CTL              0x00B0 0x0260 0x0000 0x0 0x0
+#define MX93_PAD_ENET1_TX_CTL__LPUART3_DTR_B                      0x00B0 0x0260 0x0000 0x1 0x0
+#define MX93_PAD_ENET1_TX_CTL__FLEXIO2_FLEXIO06                   0x00B0 0x0260 0x0000 0x4 0x0
+#define MX93_PAD_ENET1_TX_CTL__GPIO4_IO06                         0x00B0 0x0260 0x0000 0x5 0x0
+#define MX93_PAD_ENET1_TXC__CCM_ENET_QOS_CLOCK_GENERATE_TX_CLK    0x00B4 0x0264 0x0000 0x0 0x0
+#define MX93_PAD_ENET1_TXC__ENET_QOS_TX_ER                        0x00B4 0x0264 0x0000 0x1 0x0
+#define MX93_PAD_ENET1_TXC__FLEXIO2_FLEXIO07                      0x00B4 0x0264 0x0000 0x4 0x0
+#define MX93_PAD_ENET1_TXC__GPIO4_IO07                            0x00B4 0x0264 0x0000 0x5 0x0
+#define MX93_PAD_ENET1_RX_CTL__ENET_QOS_RGMII_RX_CTL              0x00B8 0x0268 0x0000 0x0 0x0
+#define MX93_PAD_ENET1_RX_CTL__LPUART3_DSR_B                      0x00B8 0x0268 0x0000 0x1 0x0
+#define MX93_PAD_ENET1_RX_CTL__HSIOMIX_OTG_PWR2                   0x00B8 0x0268 0x0000 0x3 0x0
+#define MX93_PAD_ENET1_RX_CTL__FLEXIO2_FLEXIO08                   0x00B8 0x0268 0x0000 0x4 0x0
+#define MX93_PAD_ENET1_RX_CTL__GPIO4_IO08                         0x00B8 0x0268 0x0000 0x5 0x0
+#define MX93_PAD_ENET1_RXC__CCM_ENET_QOS_CLOCK_GENERATE_RX_CLK    0x00BC 0x026C 0x0000 0x0 0x0
+#define MX93_PAD_ENET1_RXC__ENET_QOS_RX_ER                        0x00BC 0x026C 0x0000 0x1 0x0
+#define MX93_PAD_ENET1_RXC__FLEXIO2_FLEXIO09                      0x00BC 0x026C 0x0000 0x4 0x0
+#define MX93_PAD_ENET1_RXC__GPIO4_IO09                            0x00BC 0x026C 0x0000 0x5 0x0
+#define MX93_PAD_ENET1_RD0__ENET_QOS_RGMII_RD0                    0x00C0 0x0270 0x0000 0x0 0x0
+#define MX93_PAD_ENET1_RD0__LPUART3_RX                            0x00C0 0x0270 0x0418 0x1 0x1
+#define MX93_PAD_ENET1_RD0__FLEXIO2_FLEXIO10                      0x00C0 0x0270 0x0000 0x4 0x0
+#define MX93_PAD_ENET1_RD0__GPIO4_IO10                            0x00C0 0x0270 0x0000 0x5 0x0
+#define MX93_PAD_ENET1_RD1__ENET_QOS_RGMII_RD1                    0x00C4 0x0274 0x0000 0x0 0x0
+#define MX93_PAD_ENET1_RD1__LPUART3_CTS_B                         0x00C4 0x0274 0x0414 0x1 0x1
+#define MX93_PAD_ENET1_RD1__LPTMR2_ALT1                           0x00C4 0x0274 0x0408 0x3 0x0
+#define MX93_PAD_ENET1_RD1__FLEXIO2_FLEXIO11                      0x00C4 0x0274 0x0000 0x4 0x0
+#define MX93_PAD_ENET1_RD1__GPIO4_IO11                            0x00C4 0x0274 0x0000 0x5 0x0
+#define MX93_PAD_ENET1_RD2__ENET_QOS_RGMII_RD2                    0x00C8 0x0278 0x0000 0x0 0x0
+#define MX93_PAD_ENET1_RD2__LPTMR2_ALT2                           0x00C8 0x0278 0x040C 0x3 0x0
+#define MX93_PAD_ENET1_RD2__FLEXIO2_FLEXIO12                      0x00C8 0x0278 0x0000 0x4 0x0
+#define MX93_PAD_ENET1_RD2__GPIO4_IO12                            0x00C8 0x0278 0x0000 0x5 0x0
+#define MX93_PAD_ENET1_RD3__ENET_QOS_RGMII_RD3                    0x00CC 0x027C 0x0000 0x0 0x0
+#define MX93_PAD_ENET1_RD3__FLEXSPI1_TESTER_TRIGGER               0x00CC 0x027C 0x0000 0x2 0x0
+#define MX93_PAD_ENET1_RD3__LPTMR2_ALT3                           0x00CC 0x027C 0x0410 0x3 0x0
+#define MX93_PAD_ENET1_RD3__FLEXIO2_FLEXIO13                      0x00CC 0x027C 0x0000 0x4 0x0
+#define MX93_PAD_ENET1_RD3__GPIO4_IO13                            0x00CC 0x027C 0x0000 0x5 0x0
+#define MX93_PAD_ENET2_MDC__ENET1_MDC                             0x00D0 0x0280 0x0000 0x0 0x0
+#define MX93_PAD_ENET2_MDC__LPUART4_DCB_B                         0x00D0 0x0280 0x0000 0x1 0x0
+#define MX93_PAD_ENET2_MDC__SAI2_RX_SYNC                          0x00D0 0x0280 0x0000 0x2 0x0
+#define MX93_PAD_ENET2_MDC__FLEXIO2_FLEXIO14                      0x00D0 0x0280 0x0000 0x4 0x0
+#define MX93_PAD_ENET2_MDC__GPIO4_IO14                            0x00D0 0x0280 0x0000 0x5 0x0
+#define MX93_PAD_ENET2_MDIO__ENET1_MDIO                           0x00D4 0x0284 0x0000 0x0 0x0
+#define MX93_PAD_ENET2_MDIO__LPUART4_RIN_B                        0x00D4 0x0284 0x0000 0x1 0x0
+#define MX93_PAD_ENET2_MDIO__SAI2_RX_BCLK                         0x00D4 0x0284 0x0000 0x2 0x0
+#define MX93_PAD_ENET2_MDIO__FLEXIO2_FLEXIO15                     0x00D4 0x0284 0x0000 0x4 0x0
+#define MX93_PAD_ENET2_MDIO__GPIO4_IO15                           0x00D4 0x0284 0x0000 0x5 0x0
+#define MX93_PAD_ENET2_TD3__SAI2_RX_DATA00                        0x00D8 0x0288 0x0000 0x2 0x0
+#define MX93_PAD_ENET2_TD3__FLEXIO2_FLEXIO16                      0x00D8 0x0288 0x0000 0x4 0x0
+#define MX93_PAD_ENET2_TD3__GPIO4_IO16                            0x00D8 0x0288 0x0000 0x5 0x0
+#define MX93_PAD_ENET2_TD3__ENET1_RGMII_TD3                       0x00D8 0x0288 0x0000 0x0 0x0
+#define MX93_PAD_ENET2_TD2__ENET1_RGMII_TD2                       0x00DC 0x028C 0x0000 0x0 0x0
+#define MX93_PAD_ENET2_TD2__ENET1_TX_CLK                          0x00DC 0x028C 0x0000 0x1 0x0
+#define MX93_PAD_ENET2_TD2__SAI2_RX_DATA01                        0x00DC 0x028C 0x0000 0x2 0x0
+#define MX93_PAD_ENET2_TD2__FLEXIO2_FLEXIO17                      0x00DC 0x028C 0x0000 0x4 0x0
+#define MX93_PAD_ENET2_TD2__GPIO4_IO17                            0x00DC 0x028C 0x0000 0x5 0x0
+#define MX93_PAD_ENET2_TD1__ENET1_RGMII_TD1                       0x00E0 0x0290 0x0000 0x0 0x0
+#define MX93_PAD_ENET2_TD1__LPUART4_RTS_B                         0x00E0 0x0290 0x0000 0x1 0x0
+#define MX93_PAD_ENET2_TD1__SAI2_RX_DATA02                        0x00E0 0x0290 0x0000 0x2 0x0
+#define MX93_PAD_ENET2_TD1__FLEXIO2_FLEXIO18                      0x00E0 0x0290 0x0000 0x4 0x0
+#define MX93_PAD_ENET2_TD1__GPIO4_IO18                            0x00E0 0x0290 0x0000 0x5 0x0
+#define MX93_PAD_ENET2_TD0__ENET1_RGMII_TD0                       0x00E4 0x0294 0x0000 0x0 0x0
+#define MX93_PAD_ENET2_TD0__LPUART4_TX                            0x00E4 0x0294 0x0428 0x1 0x1
+#define MX93_PAD_ENET2_TD0__SAI2_RX_DATA03                        0x00E4 0x0294 0x0000 0x2 0x0
+#define MX93_PAD_ENET2_TD0__FLEXIO2_FLEXIO19                      0x00E4 0x0294 0x0000 0x4 0x0
+#define MX93_PAD_ENET2_TD0__GPIO4_IO19                            0x00E4 0x0294 0x0000 0x5 0x0
+#define MX93_PAD_ENET2_TX_CTL__ENET1_RGMII_TX_CTL                 0x00E8 0x0298 0x0000 0x0 0x0
+#define MX93_PAD_ENET2_TX_CTL__LPUART4_DTR_B                      0x00E8 0x0298 0x0000 0x1 0x0
+#define MX93_PAD_ENET2_TX_CTL__SAI2_TX_SYNC                       0x00E8 0x0298 0x0000 0x2 0x0
+#define MX93_PAD_ENET2_TX_CTL__FLEXIO2_FLEXIO20                   0x00E8 0x0298 0x0000 0x4 0x0
+#define MX93_PAD_ENET2_TX_CTL__GPIO4_IO20                         0x00E8 0x0298 0x0000 0x5 0x0
+#define MX93_PAD_ENET2_TXC__ENET1_RGMII_TXC                       0x00EC 0x029C 0x0000 0x0 0x0
+#define MX93_PAD_ENET2_TXC__ENET1_TX_ER                           0x00EC 0x029C 0x0000 0x1 0x0
+#define MX93_PAD_ENET2_TXC__SAI2_TX_BCLK                          0x00EC 0x029C 0x0000 0x2 0x0
+#define MX93_PAD_ENET2_TXC__FLEXIO2_FLEXIO21                      0x00EC 0x029C 0x0000 0x4 0x0
+#define MX93_PAD_ENET2_TXC__GPIO4_IO21                            0x00EC 0x029C 0x0000 0x5 0x0
+#define MX93_PAD_ENET2_RX_CTL__ENET1_RGMII_RX_CTL                 0x00F0 0x02A0 0x0000 0x0 0x0
+#define MX93_PAD_ENET2_RX_CTL__LPUART4_DSR_B                      0x00F0 0x02A0 0x0000 0x1 0x0
+#define MX93_PAD_ENET2_RX_CTL__SAI2_TX_DATA00                     0x00F0 0x02A0 0x0000 0x2 0x0
+#define MX93_PAD_ENET2_RX_CTL__FLEXIO2_FLEXIO22                   0x00F0 0x02A0 0x0000 0x4 0x0
+#define MX93_PAD_ENET2_RX_CTL__GPIO4_IO22                         0x00F0 0x02A0 0x0000 0x5 0x0
+#define MX93_PAD_ENET2_RXC__ENET1_RGMII_RXC                       0x00F4 0x02A4 0x0000 0x0 0x0
+#define MX93_PAD_ENET2_RXC__ENET1_RX_ER                           0x00F4 0x02A4 0x0000 0x1 0x0
+#define MX93_PAD_ENET2_RXC__SAI2_TX_DATA01                        0x00F4 0x02A4 0x0000 0x2 0x0
+#define MX93_PAD_ENET2_RXC__FLEXIO2_FLEXIO23                      0x00F4 0x02A4 0x0000 0x4 0x0
+#define MX93_PAD_ENET2_RXC__GPIO4_IO23                            0x00F4 0x02A4 0x0000 0x5 0x0
+#define MX93_PAD_ENET2_RD0__ENET1_RGMII_RD0                       0x00F8 0x02A8 0x0000 0x0 0x0
+#define MX93_PAD_ENET2_RD0__LPUART4_RX                            0x00F8 0x02A8 0x0424 0x1 0x1
+#define MX93_PAD_ENET2_RD0__SAI2_TX_DATA02                        0x00F8 0x02A8 0x0000 0x2 0x0
+#define MX93_PAD_ENET2_RD0__FLEXIO2_FLEXIO24                      0x00F8 0x02A8 0x0000 0x4 0x0
+#define MX93_PAD_ENET2_RD0__GPIO4_IO24                            0x00F8 0x02A8 0x0000 0x5 0x0
+#define MX93_PAD_ENET2_RD1__ENET1_RGMII_RD1                       0x00FC 0x02AC 0x0000 0x0 0x0
+#define MX93_PAD_ENET2_RD1__SPDIF_IN                              0x00FC 0x02AC 0x0454 0x1 0x1
+#define MX93_PAD_ENET2_RD1__SAI2_TX_DATA03                        0x00FC 0x02AC 0x0000 0x2 0x0
+#define MX93_PAD_ENET2_RD1__FLEXIO2_FLEXIO25                      0x00FC 0x02AC 0x0000 0x4 0x0
+#define MX93_PAD_ENET2_RD1__GPIO4_IO25                            0x00FC 0x02AC 0x0000 0x5 0x0
+#define MX93_PAD_ENET2_RD2__ENET1_RGMII_RD2                       0x0100 0x02B0 0x0000 0x0 0x0
+#define MX93_PAD_ENET2_RD2__LPUART4_CTS_B                         0x0100 0x02B0 0x0420 0x1 0x1
+#define MX93_PAD_ENET2_RD2__SAI2_MCLK                             0x0100 0x02B0 0x0000 0x2 0x0
+#define MX93_PAD_ENET2_RD2__MQS2_RIGHT                            0x0100 0x02B0 0x0000 0x3 0x0
+#define MX93_PAD_ENET2_RD2__FLEXIO2_FLEXIO26                      0x0100 0x02B0 0x0000 0x4 0x0
+#define MX93_PAD_ENET2_RD2__GPIO4_IO26                            0x0100 0x02B0 0x0000 0x5 0x0
+#define MX93_PAD_ENET2_RD3__ENET1_RGMII_RD3                       0x0104 0x02B4 0x0000 0x0 0x0
+#define MX93_PAD_ENET2_RD3__SPDIF_OUT                             0x0104 0x02B4 0x0000 0x1 0x0
+#define MX93_PAD_ENET2_RD3__SPDIF_IN                              0x0104 0x02B4 0x0454 0x2 0x2
+#define MX93_PAD_ENET2_RD3__MQS2_LEFT                             0x0104 0x02B4 0x0000 0x3 0x0
+#define MX93_PAD_ENET2_RD3__FLEXIO2_FLEXIO27                      0x0104 0x02B4 0x0000 0x4 0x0
+#define MX93_PAD_ENET2_RD3__GPIO4_IO27                            0x0104 0x02B4 0x0000 0x5 0x0
+#define MX93_PAD_SD1_CLK__FLEXIO1_FLEXIO08                        0x0108 0x02B8 0x038C 0x4 0x1
+#define MX93_PAD_SD1_CLK__GPIO3_IO08                              0x0108 0x02B8 0x0000 0x5 0x0
+#define MX93_PAD_SD1_CLK__USDHC1_CLK                              0x0108 0x02B8 0x0000 0x0 0x0
+#define MX93_PAD_SD1_CMD__USDHC1_CMD                              0x010C 0x02BC 0x0000 0x0 0x0
+#define MX93_PAD_SD1_CMD__FLEXIO1_FLEXIO09                        0x010C 0x02BC 0x0390 0x4 0x1
+#define MX93_PAD_SD1_CMD__GPIO3_IO09                              0x010C 0x02BC 0x0000 0x5 0x0
+#define MX93_PAD_SD1_DATA0__USDHC1_DATA0                          0x0110 0x02C0 0x0000 0x0 0x0
+#define MX93_PAD_SD1_DATA0__FLEXIO1_FLEXIO10                      0x0110 0x02C0 0x0394 0x4 0x1
+#define MX93_PAD_SD1_DATA0__GPIO3_IO10                            0x0110 0x02C0 0x0000 0x5 0x0
+#define MX93_PAD_SD1_DATA1__USDHC1_DATA1                          0x0114 0x02C4 0x0000 0x0 0x0
+#define MX93_PAD_SD1_DATA1__FLEXIO1_FLEXIO11                      0x0114 0x02C4 0x0398 0x4 0x1
+#define MX93_PAD_SD1_DATA1__GPIO3_IO11                            0x0114 0x02C4 0x0000 0x5 0x0
+#define MX93_PAD_SD1_DATA1__CCMSRCGPCMIX_INT_BOOT                 0x0114 0x02C4 0x0000 0x6 0x0
+#define MX93_PAD_SD1_DATA2__USDHC1_DATA2                          0x0118 0x02C8 0x0000 0x0 0x0
+#define MX93_PAD_SD1_DATA2__FLEXIO1_FLEXIO12                      0x0118 0x02C8 0x0000 0x4 0x0
+#define MX93_PAD_SD1_DATA2__GPIO3_IO12                            0x0118 0x02C8 0x0000 0x5 0x0
+#define MX93_PAD_SD1_DATA2__CCMSRCGPCMIX_PMIC_READY               0x0118 0x02C8 0x0000 0x6 0x0
+#define MX93_PAD_SD1_DATA3__USDHC1_DATA3                          0x011C 0x02CC 0x0000 0x0 0x0
+#define MX93_PAD_SD1_DATA3__FLEXSPI1_A_SS1_B                      0x011C 0x02CC 0x0000 0x1 0x0
+#define MX93_PAD_SD1_DATA3__FLEXIO1_FLEXIO13                      0x011C 0x02CC 0x039C 0x4 0x1
+#define MX93_PAD_SD1_DATA3__GPIO3_IO13                            0x011C 0x02CC 0x0000 0x5 0x0
+#define MX93_PAD_SD1_DATA4__USDHC1_DATA4                          0x0120 0x02D0 0x0000 0x0 0x0
+#define MX93_PAD_SD1_DATA4__FLEXSPI1_A_DATA04                     0x0120 0x02D0 0x0000 0x1 0x0
+#define MX93_PAD_SD1_DATA4__FLEXIO1_FLEXIO14                      0x0120 0x02D0 0x03A0 0x4 0x1
+#define MX93_PAD_SD1_DATA4__GPIO3_IO14                            0x0120 0x02D0 0x0000 0x5 0x0
+#define MX93_PAD_SD1_DATA5__USDHC1_DATA5                          0x0124 0x02D4 0x0000 0x0 0x0
+#define MX93_PAD_SD1_DATA5__FLEXSPI1_A_DATA05                     0x0124 0x02D4 0x0000 0x1 0x0
+#define MX93_PAD_SD1_DATA5__USDHC1_RESET_B                        0x0124 0x02D4 0x0000 0x2 0x0
+#define MX93_PAD_SD1_DATA5__FLEXIO1_FLEXIO15                      0x0124 0x02D4 0x03A4 0x4 0x1
+#define MX93_PAD_SD1_DATA5__GPIO3_IO15                            0x0124 0x02D4 0x0000 0x5 0x0
+#define MX93_PAD_SD1_DATA6__USDHC1_DATA6                          0x0128 0x02D8 0x0000 0x0 0x0
+#define MX93_PAD_SD1_DATA6__FLEXSPI1_A_DATA06                     0x0128 0x02D8 0x0000 0x1 0x0
+#define MX93_PAD_SD1_DATA6__USDHC1_CD_B                           0x0128 0x02D8 0x0000 0x2 0x0
+#define MX93_PAD_SD1_DATA6__FLEXIO1_FLEXIO16                      0x0128 0x02D8 0x03A8 0x4 0x1
+#define MX93_PAD_SD1_DATA6__GPIO3_IO16                            0x0128 0x02D8 0x0000 0x5 0x0
+#define MX93_PAD_SD1_DATA7__USDHC1_DATA7                          0x012C 0x02DC 0x0000 0x0 0x0
+#define MX93_PAD_SD1_DATA7__FLEXSPI1_A_DATA07                     0x012C 0x02DC 0x0000 0x1 0x0
+#define MX93_PAD_SD1_DATA7__USDHC1_WP                             0x012C 0x02DC 0x0000 0x2 0x0
+#define MX93_PAD_SD1_DATA7__FLEXIO1_FLEXIO17                      0x012C 0x02DC 0x03AC 0x4 0x1
+#define MX93_PAD_SD1_DATA7__GPIO3_IO17                            0x012C 0x02DC 0x0000 0x5 0x0
+#define MX93_PAD_SD1_STROBE__USDHC1_STROBE                        0x0130 0x02E0 0x0000 0x0 0x0
+#define MX93_PAD_SD1_STROBE__FLEXSPI1_A_DQS                       0x0130 0x02E0 0x0000 0x1 0x0
+#define MX93_PAD_SD1_STROBE__FLEXIO1_FLEXIO18                     0x0130 0x02E0 0x03B0 0x4 0x1
+#define MX93_PAD_SD1_STROBE__GPIO3_IO18                           0x0130 0x02E0 0x0000 0x5 0x0
+#define MX93_PAD_SD2_VSELECT__USDHC2_VSELECT                      0x0134 0x02E4 0x0000 0x0 0x0
+#define MX93_PAD_SD2_VSELECT__USDHC2_WP                           0x0134 0x02E4 0x0000 0x1 0x0
+#define MX93_PAD_SD2_VSELECT__LPTMR2_ALT3                         0x0134 0x02E4 0x0410 0x2 0x1
+#define MX93_PAD_SD2_VSELECT__FLEXIO1_FLEXIO19                    0x0134 0x02E4 0x0000 0x4 0x0
+#define MX93_PAD_SD2_VSELECT__GPIO3_IO19                          0x0134 0x02E4 0x0000 0x5 0x0
+#define MX93_PAD_SD2_VSELECT__CCMSRCGPCMIX_EXT_CLK1               0x0134 0x02E4 0x0368 0x6 0x0
+#define MX93_PAD_SD3_CLK__USDHC3_CLK                              0x0138 0x02E8 0x0458 0x0 0x1
+#define MX93_PAD_SD3_CLK__FLEXSPI1_A_SCLK                         0x0138 0x02E8 0x0000 0x1 0x0
+#define MX93_PAD_SD3_CLK__FLEXIO1_FLEXIO20                        0x0138 0x02E8 0x03B4 0x4 0x1
+#define MX93_PAD_SD3_CLK__GPIO3_IO20                              0x0138 0x02E8 0x0000 0x5 0x0
+#define MX93_PAD_SD3_CMD__USDHC3_CMD                              0x013C 0x02EC 0x045C 0x0 0x1
+#define MX93_PAD_SD3_CMD__FLEXSPI1_A_SS0_B                        0x013C 0x02EC 0x0000 0x1 0x0
+#define MX93_PAD_SD3_CMD__FLEXIO1_FLEXIO21                        0x013C 0x02EC 0x0000 0x4 0x0
+#define MX93_PAD_SD3_CMD__GPIO3_IO21                              0x013C 0x02EC 0x0000 0x5 0x0
+#define MX93_PAD_SD3_DATA0__USDHC3_DATA0                          0x0140 0x02F0 0x0460 0x0 0x1
+#define MX93_PAD_SD3_DATA0__FLEXSPI1_A_DATA00                     0x0140 0x02F0 0x0000 0x1 0x0
+#define MX93_PAD_SD3_DATA0__FLEXIO1_FLEXIO22                      0x0140 0x02F0 0x03B8 0x4 0x1
+#define MX93_PAD_SD3_DATA0__GPIO3_IO22                            0x0140 0x02F0 0x0000 0x5 0x0
+#define MX93_PAD_SD3_DATA1__USDHC3_DATA1                          0x0144 0x02F4 0x0464 0x0 0x1
+#define MX93_PAD_SD3_DATA1__FLEXSPI1_A_DATA01                     0x0144 0x02F4 0x0000 0x1 0x0
+#define MX93_PAD_SD3_DATA1__FLEXIO1_FLEXIO23                      0x0144 0x02F4 0x03BC 0x4 0x1
+#define MX93_PAD_SD3_DATA1__GPIO3_IO23                            0x0144 0x02F4 0x0000 0x5 0x0
+#define MX93_PAD_SD3_DATA2__USDHC3_DATA2                          0x0148 0x02F8 0x0468 0x0 0x1
+#define MX93_PAD_SD3_DATA2__FLEXSPI1_A_DATA02                     0x0148 0x02F8 0x0000 0x1 0x0
+#define MX93_PAD_SD3_DATA2__FLEXIO1_FLEXIO24                      0x0148 0x02F8 0x03C0 0x4 0x1
+#define MX93_PAD_SD3_DATA2__GPIO3_IO24                            0x0148 0x02F8 0x0000 0x5 0x0
+#define MX93_PAD_SD3_DATA3__USDHC3_DATA3                          0x014C 0x02FC 0x046C 0x0 0x1
+#define MX93_PAD_SD3_DATA3__FLEXSPI1_A_DATA03                     0x014C 0x02FC 0x0000 0x1 0x0
+#define MX93_PAD_SD3_DATA3__FLEXIO1_FLEXIO25                      0x014C 0x02FC 0x03C4 0x4 0x1
+#define MX93_PAD_SD3_DATA3__GPIO3_IO25                            0x014C 0x02FC 0x0000 0x5 0x0
+#define MX93_PAD_SD2_CD_B__USDHC2_CD_B                            0x0150 0x0300 0x0000 0x0 0x0
+#define MX93_PAD_SD2_CD_B__ENET_QOS_1588_EVENT0_IN                0x0150 0x0300 0x0000 0x1 0x0
+#define MX93_PAD_SD2_CD_B__I3C2_SCL                               0x0150 0x0300 0x03CC 0x2 0x1
+#define MX93_PAD_SD2_CD_B__FLEXIO1_FLEXIO00                       0x0150 0x0300 0x036C 0x4 0x1
+#define MX93_PAD_SD2_CD_B__GPIO3_IO00                             0x0150 0x0300 0x0000 0x5 0x0
+#define MX93_PAD_SD2_CLK__USDHC2_CLK                              0x0154 0x0304 0x0000 0x0 0x0
+#define MX93_PAD_SD2_CLK__ENET_QOS_1588_EVENT0_OUT                0x0154 0x0304 0x0000 0x1 0x0
+#define MX93_PAD_SD2_CLK__I3C2_SDA                                0x0154 0x0304 0x03D0 0x2 0x1
+#define MX93_PAD_SD2_CLK__FLEXIO1_FLEXIO01                        0x0154 0x0304 0x0370 0x4 0x1
+#define MX93_PAD_SD2_CLK__GPIO3_IO01                              0x0154 0x0304 0x0000 0x5 0x0
+#define MX93_PAD_SD2_CLK__CCMSRCGPCMIX_OBSERVE0                   0x0154 0x0304 0x0000 0x6 0x0
+#define MX93_PAD_SD2_CMD__USDHC2_CMD                              0x0158 0x0308 0x0000 0x0 0x0
+#define MX93_PAD_SD2_CMD__ENET1_1588_EVENT0_IN                    0x0158 0x0308 0x0000 0x1 0x0
+#define MX93_PAD_SD2_CMD__I3C2_PUR                                0x0158 0x0308 0x0000 0x2 0x0
+#define MX93_PAD_SD2_CMD__I3C2_PUR_B                              0x0158 0x0308 0x0000 0x3 0x0
+#define MX93_PAD_SD2_CMD__FLEXIO1_FLEXIO02                        0x0158 0x0308 0x0374 0x4 0x1
+#define MX93_PAD_SD2_CMD__GPIO3_IO02                              0x0158 0x0308 0x0000 0x5 0x0
+#define MX93_PAD_SD2_CMD__CCMSRCGPCMIX_OBSERVE1                   0x0158 0x0308 0x0000 0x6 0x0
+#define MX93_PAD_SD2_DATA0__USDHC2_DATA0                          0x015C 0x030C 0x0000 0x0 0x0
+#define MX93_PAD_SD2_DATA0__ENET1_1588_EVENT0_OUT                 0x015C 0x030C 0x0000 0x1 0x0
+#define MX93_PAD_SD2_DATA0__CAN2_TX                               0x015C 0x030C 0x0000 0x2 0x0
+#define MX93_PAD_SD2_DATA0__FLEXIO1_FLEXIO03                      0x015C 0x030C 0x0378 0x4 0x1
+#define MX93_PAD_SD2_DATA0__GPIO3_IO03                            0x015C 0x030C 0x0000 0x5 0x0
+#define MX93_PAD_SD2_DATA0__CCMSRCGPCMIX_OBSERVE2                 0x015C 0x030C 0x0000 0x6 0x0
+#define MX93_PAD_SD2_DATA1__USDHC2_DATA1                          0x0160 0x0310 0x0000 0x0 0x0
+#define MX93_PAD_SD2_DATA1__ENET1_1588_EVENT1_IN                  0x0160 0x0310 0x0000 0x1 0x0
+#define MX93_PAD_SD2_DATA1__CAN2_RX                               0x0160 0x0310 0x0364 0x2 0x3
+#define MX93_PAD_SD2_DATA1__FLEXIO1_FLEXIO04                      0x0160 0x0310 0x037C 0x4 0x1
+#define MX93_PAD_SD2_DATA1__GPIO3_IO04                            0x0160 0x0310 0x0000 0x5 0x0
+#define MX93_PAD_SD2_DATA1__CCMSRCGPCMIX_WAIT                     0x0160 0x0310 0x0000 0x6 0x0
+#define MX93_PAD_SD2_DATA2__USDHC2_DATA2                          0x0164 0x0314 0x0000 0x0 0x0
+#define MX93_PAD_SD2_DATA2__ENET1_1588_EVENT1_OUT                 0x0164 0x0314 0x0000 0x1 0x0
+#define MX93_PAD_SD2_DATA2__MQS2_RIGHT                            0x0164 0x0314 0x0000 0x2 0x0
+#define MX93_PAD_SD2_DATA2__FLEXIO1_FLEXIO05                      0x0164 0x0314 0x0380 0x4 0x1
+#define MX93_PAD_SD2_DATA2__GPIO3_IO05                            0x0164 0x0314 0x0000 0x5 0x0
+#define MX93_PAD_SD2_DATA2__CCMSRCGPCMIX_STOP                     0x0164 0x0314 0x0000 0x6 0x0
+#define MX93_PAD_SD2_DATA3__USDHC2_DATA3                          0x0168 0x0318 0x0000 0x0 0x0
+#define MX93_PAD_SD2_DATA3__LPTMR2_ALT1                           0x0168 0x0318 0x0408 0x1 0x1
+#define MX93_PAD_SD2_DATA3__MQS2_LEFT                             0x0168 0x0318 0x0000 0x2 0x0
+#define MX93_PAD_SD2_DATA3__FLEXIO1_FLEXIO06                      0x0168 0x0318 0x0384 0x4 0x1
+#define MX93_PAD_SD2_DATA3__GPIO3_IO06                            0x0168 0x0318 0x0000 0x5 0x0
+#define MX93_PAD_SD2_DATA3__CCMSRCGPCMIX_EARLY_RESET              0x0168 0x0318 0x0000 0x6 0x0
+#define MX93_PAD_SD2_RESET_B__USDHC2_RESET_B                      0x016C 0x031C 0x0000 0x0 0x0
+#define MX93_PAD_SD2_RESET_B__LPTMR2_ALT2                         0x016C 0x031C 0x040C 0x1 0x1
+#define MX93_PAD_SD2_RESET_B__FLEXIO1_FLEXIO07                    0x016C 0x031C 0x0388 0x4 0x1
+#define MX93_PAD_SD2_RESET_B__GPIO3_IO07                          0x016C 0x031C 0x0000 0x5 0x0
+#define MX93_PAD_SD2_RESET_B__CCMSRCGPCMIX_SYSTEM_RESET           0x016C 0x031C 0x0000 0x6 0x0
+#define MX93_PAD_I2C1_SCL__LPI2C1_SCL                             0x0170 0x0320 0x0000 0x10 0x0
+#define MX93_PAD_I2C1_SCL__I3C1_SCL                               0x0170 0x0320 0x0000 0x1 0x0
+#define MX93_PAD_I2C1_SCL__LPUART1_DCB_B                          0x0170 0x0320 0x0000 0x2 0x0
+#define MX93_PAD_I2C1_SCL__TPM2_CH0                               0x0170 0x0320 0x0000 0x3 0x0
+#define MX93_PAD_I2C1_SCL__GPIO1_IO00                             0x0170 0x0320 0x0000 0x5 0x0
+#define MX93_PAD_I2C1_SDA__LPI2C1_SDA                             0x0174 0x0324 0x0000 0x10 0x0
+#define MX93_PAD_I2C1_SDA__I3C1_SDA                               0x0174 0x0324 0x0000 0x1 0x0
+#define MX93_PAD_I2C1_SDA__LPUART1_RIN_B                          0x0174 0x0324 0x0000 0x2 0x0
+#define MX93_PAD_I2C1_SDA__TPM2_CH1                               0x0174 0x0324 0x0000 0x3 0x0
+#define MX93_PAD_I2C1_SDA__GPIO1_IO01                             0x0174 0x0324 0x0000 0x5 0x0
+#define MX93_PAD_I2C2_SCL__LPI2C2_SCL                             0x0178 0x0328 0x0000 0x10 0x0
+#define MX93_PAD_I2C2_SCL__I3C1_PUR                               0x0178 0x0328 0x0000 0x1 0x0
+#define MX93_PAD_I2C2_SCL__LPUART2_DCB_B                          0x0178 0x0328 0x0000 0x2 0x0
+#define MX93_PAD_I2C2_SCL__TPM2_CH2                               0x0178 0x0328 0x0000 0x3 0x0
+#define MX93_PAD_I2C2_SCL__SAI1_RX_SYNC                           0x0178 0x0328 0x0000 0x4 0x0
+#define MX93_PAD_I2C2_SCL__GPIO1_IO02                             0x0178 0x0328 0x0000 0x5 0x0
+#define MX93_PAD_I2C2_SCL__I3C1_PUR_B                             0x0178 0x0328 0x0000 0x6 0x0
+#define MX93_PAD_I2C2_SDA__LPI2C2_SDA                             0x017C 0x032C 0x0000 0x10 0x0
+#define MX93_PAD_I2C2_SDA__LPUART2_RIN_B                          0x017C 0x032C 0x0000 0x2 0x0
+#define MX93_PAD_I2C2_SDA__TPM2_CH3                               0x017C 0x032C 0x0000 0x3 0x0
+#define MX93_PAD_I2C2_SDA__SAI1_RX_BCLK                           0x017C 0x032C 0x0000 0x4 0x0
+#define MX93_PAD_I2C2_SDA__GPIO1_IO03                             0x017C 0x032C 0x0000 0x5 0x0
+#define MX93_PAD_UART1_RXD__LPUART1_RX                            0x0180 0x0330 0x0000 0x0 0x0
+#define MX93_PAD_UART1_RXD__S400_UART_RX                          0x0180 0x0330 0x0000 0x1 0x0
+#define MX93_PAD_UART1_RXD__LPSPI2_SIN                            0x0180 0x0330 0x0000 0x2 0x0
+#define MX93_PAD_UART1_RXD__TPM1_CH0                              0x0180 0x0330 0x0000 0x3 0x0
+#define MX93_PAD_UART1_RXD__GPIO1_IO04                            0x0180 0x0330 0x0000 0x5 0x0
+#define MX93_PAD_UART1_TXD__LPUART1_TX                            0x0184 0x0334 0x0000 0x0 0x0
+#define MX93_PAD_UART1_TXD__S400_UART_TX                          0x0184 0x0334 0x0000 0x1 0x0
+#define MX93_PAD_UART1_TXD__LPSPI2_PCS0                           0x0184 0x0334 0x0000 0x2 0x0
+#define MX93_PAD_UART1_TXD__TPM1_CH1                              0x0184 0x0334 0x0000 0x3 0x0
+#define MX93_PAD_UART1_TXD__GPIO1_IO05                            0x0184 0x0334 0x0000 0x5 0x0
+#define MX93_PAD_UART2_RXD__LPUART2_RX                            0x0188 0x0338 0x0000 0x0 0x0
+#define MX93_PAD_UART2_RXD__LPUART1_CTS_B                         0x0188 0x0338 0x0000 0x1 0x0
+#define MX93_PAD_UART2_RXD__LPSPI2_SOUT                           0x0188 0x0338 0x0000 0x2 0x0
+#define MX93_PAD_UART2_RXD__TPM1_CH2                              0x0188 0x0338 0x0000 0x3 0x0
+#define MX93_PAD_UART2_RXD__SAI1_MCLK                             0x0188 0x0338 0x0448 0x4 0x0
+#define MX93_PAD_UART2_RXD__GPIO1_IO06                            0x0188 0x0338 0x0000 0x5 0x0
+#define MX93_PAD_UART2_TXD__LPUART2_TX                            0x018C 0x033C 0x0000 0x0 0x0
+#define MX93_PAD_UART2_TXD__LPUART1_RTS_B                         0x018C 0x033C 0x0000 0x1 0x0
+#define MX93_PAD_UART2_TXD__LPSPI2_SCK                            0x018C 0x033C 0x0000 0x2 0x0
+#define MX93_PAD_UART2_TXD__TPM1_CH3                              0x018C 0x033C 0x0000 0x3 0x0
+#define MX93_PAD_UART2_TXD__GPIO1_IO07                            0x018C 0x033C 0x0000 0x5 0x0
+#define MX93_PAD_PDM_CLK__PDM_CLK                                 0x0190 0x0340 0x0000 0x0 0x0
+#define MX93_PAD_PDM_CLK__MQS1_LEFT                               0x0190 0x0340 0x0000 0x1 0x0
+#define MX93_PAD_PDM_CLK__LPTMR1_ALT1                             0x0190 0x0340 0x0000 0x4 0x0
+#define MX93_PAD_PDM_CLK__GPIO1_IO08                              0x0190 0x0340 0x0000 0x5 0x0
+#define MX93_PAD_PDM_CLK__CAN1_TX                                 0x0190 0x0340 0x0000 0x6 0x0
+#define MX93_PAD_PDM_BIT_STREAM0__PDM_BIT_STREAM00                0x0194 0x0344 0x0438 0x0 0x2
+#define MX93_PAD_PDM_BIT_STREAM0__MQS1_RIGHT                      0x0194 0x0344 0x0000 0x1 0x0
+#define MX93_PAD_PDM_BIT_STREAM0__LPSPI1_PCS1                     0x0194 0x0344 0x0000 0x2 0x0
+#define MX93_PAD_PDM_BIT_STREAM0__TPM1_EXTCLK                     0x0194 0x0344 0x0000 0x3 0x0
+#define MX93_PAD_PDM_BIT_STREAM0__LPTMR1_ALT2                     0x0194 0x0344 0x0000 0x4 0x0
+#define MX93_PAD_PDM_BIT_STREAM0__GPIO1_IO09                      0x0194 0x0344 0x0000 0x5 0x0
+#define MX93_PAD_PDM_BIT_STREAM0__CAN1_RX                         0x0194 0x0344 0x0360 0x6 0x0
+#define MX93_PAD_PDM_BIT_STREAM1__PDM_BIT_STREAM01                0x0198 0x0348 0x043C 0x0 0x2
+#define MX93_PAD_PDM_BIT_STREAM1__NMI_GLUE_NMI                    0x0198 0x0348 0x0000 0x1 0x0
+#define MX93_PAD_PDM_BIT_STREAM1__LPSPI2_PCS1                     0x0198 0x0348 0x0000 0x2 0x0
+#define MX93_PAD_PDM_BIT_STREAM1__TPM2_EXTCLK                     0x0198 0x0348 0x0000 0x3 0x0
+#define MX93_PAD_PDM_BIT_STREAM1__LPTMR1_ALT3                     0x0198 0x0348 0x0000 0x4 0x0
+#define MX93_PAD_PDM_BIT_STREAM1__GPIO1_IO10                      0x0198 0x0348 0x0000 0x5 0x0
+#define MX93_PAD_PDM_BIT_STREAM1__CCMSRCGPCMIX_EXT_CLK1           0x0198 0x0348 0x0368 0x6 0x1
+#define MX93_PAD_SAI1_TXFS__SAI1_TX_SYNC                          0x019C 0x034C 0x0000 0x0 0x0
+#define MX93_PAD_SAI1_TXFS__SAI1_TX_DATA01                        0x019C 0x034C 0x0000 0x1 0x0
+#define MX93_PAD_SAI1_TXFS__LPSPI1_PCS0                           0x019C 0x034C 0x0000 0x2 0x0
+#define MX93_PAD_SAI1_TXFS__LPUART2_DTR_B                         0x019C 0x034C 0x0000 0x3 0x0
+#define MX93_PAD_SAI1_TXFS__MQS1_LEFT                             0x019C 0x034C 0x0000 0x4 0x0
+#define MX93_PAD_SAI1_TXFS__GPIO1_IO11                            0x019C 0x034C 0x0000 0x5 0x0
+#define MX93_PAD_SAI1_TXC__SAI1_TX_BCLK                           0x01A0 0x0350 0x0000 0x0 0x0
+#define MX93_PAD_SAI1_TXC__LPUART2_CTS_B                          0x01A0 0x0350 0x0000 0x1 0x0
+#define MX93_PAD_SAI1_TXC__LPSPI1_SIN                             0x01A0 0x0350 0x0000 0x2 0x0
+#define MX93_PAD_SAI1_TXC__LPUART1_DSR_B                          0x01A0 0x0350 0x0000 0x3 0x0
+#define MX93_PAD_SAI1_TXC__CAN1_RX                                0x01A0 0x0350 0x0360 0x4 0x1
+#define MX93_PAD_SAI1_TXC__GPIO1_IO12                             0x01A0 0x0350 0x0000 0x5 0x0
+#define MX93_PAD_SAI1_TXD0__SAI1_TX_DATA00                        0x01A4 0x0354 0x0000 0x0 0x0
+#define MX93_PAD_SAI1_TXD0__LPUART2_RTS_B                         0x01A4 0x0354 0x0000 0x1 0x0
+#define MX93_PAD_SAI1_TXD0__LPSPI1_SCK                            0x01A4 0x0354 0x0000 0x2 0x0
+#define MX93_PAD_SAI1_TXD0__LPUART1_DTR_B                         0x01A4 0x0354 0x0000 0x3 0x0
+#define MX93_PAD_SAI1_TXD0__CAN1_TX                               0x01A4 0x0354 0x0000 0x4 0x0
+#define MX93_PAD_SAI1_TXD0__GPIO1_IO13                            0x01A4 0x0354 0x0000 0x5 0x0
+#define MX93_PAD_SAI1_RXD0__SAI1_RX_DATA00                        0x01A8 0x0358 0x0000 0x0 0x0
+#define MX93_PAD_SAI1_RXD0__SAI1_MCLK                             0x01A8 0x0358 0x0448 0x1 0x1
+#define MX93_PAD_SAI1_RXD0__LPSPI1_SOUT                           0x01A8 0x0358 0x0000 0x2 0x0
+#define MX93_PAD_SAI1_RXD0__LPUART2_DSR_B                         0x01A8 0x0358 0x0000 0x3 0x0
+#define MX93_PAD_SAI1_RXD0__MQS1_RIGHT                            0x01A8 0x0358 0x0000 0x4 0x0
+#define MX93_PAD_SAI1_RXD0__GPIO1_IO14                            0x01A8 0x0358 0x0000 0x5 0x0
+#define MX93_PAD_WDOG_ANY__WDOG1_WDOG_ANY                         0x01AC 0x035C 0x0000 0x0 0x0
+#define MX93_PAD_WDOG_ANY__GPIO1_IO15                             0x01AC 0x035C 0x0000 0x5 0x0
+
+#endif /* __DTS_IMX93_PINFUNC_H */
diff --git a/arch/arm64/boot/dts/freescale/imx93.dtsi b/arch/arm64/boot/dts/freescale/imx93.dtsi
new file mode 100644
index 000000000000..0247866fc86b
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx93.dtsi
@@ -0,0 +1,529 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2022 NXP
+ */
+
+#include <dt-bindings/clock/imx93-clock.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/power/fsl,imx93-power.h>
+
+#include "imx93-pinfunc.h"
+
+/ {
+	interrupt-parent = <&gic>;
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	aliases {
+		i2c0 = &lpi2c1;
+		i2c1 = &lpi2c2;
+		i2c2 = &lpi2c3;
+		i2c3 = &lpi2c4;
+		i2c4 = &lpi2c5;
+		i2c5 = &lpi2c6;
+		i2c6 = &lpi2c7;
+		i2c7 = &lpi2c8;
+		mmc0 = &usdhc1;
+		mmc1 = &usdhc2;
+		mmc2 = &usdhc3;
+		serial0 = &lpuart1;
+		serial1 = &lpuart2;
+		serial2 = &lpuart3;
+		serial3 = &lpuart4;
+		serial4 = &lpuart5;
+		serial5 = &lpuart6;
+		serial6 = &lpuart7;
+		serial7 = &lpuart8;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		A55_0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a55";
+			reg = <0x0>;
+			enable-method = "psci";
+			#cooling-cells = <2>;
+		};
+
+		A55_1: cpu@100 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a55";
+			reg = <0x100>;
+			enable-method = "psci";
+			#cooling-cells = <2>;
+		};
+
+	};
+
+	osc_32k: clock-osc-32k {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		clock-output-names = "osc_32k";
+	};
+
+	osc_24m: clock-osc-24m {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <24000000>;
+		clock-output-names = "osc_24m";
+	};
+
+	clk_ext1: clock-ext1 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <133000000>;
+		clock-output-names = "clk_ext1";
+	};
+
+	pmu {
+		compatible = "arm,cortex-a55-pmu";
+		interrupts = <GIC_PPI 7 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_HIGH)>;
+	};
+
+	psci {
+		compatible = "arm,psci-1.0";
+		method = "smc";
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(6) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(6) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(6) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(6) | IRQ_TYPE_LEVEL_LOW)>;
+		clock-frequency = <24000000>;
+		arm,no-tick-in-suspend;
+		interrupt-parent = <&gic>;
+	};
+
+	gic: interrupt-controller@48000000 {
+		compatible = "arm,gic-v3";
+		reg = <0 0x48000000 0 0x10000>,
+		      <0 0x48040000 0 0xc0000>;
+		#interrupt-cells = <3>;
+		interrupt-controller;
+		interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-parent = <&gic>;
+	};
+
+	soc@0 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x0 0x0 0x80000000>,
+			 <0x28000000 0x0 0x28000000 0x10000000>;
+
+		aips1: bus@44000000 {
+			compatible = "fsl,aips-bus", "simple-bus";
+			reg = <0x44000000 0x800000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			anomix_ns_gpr: syscon@44210000 {
+				compatible = "fsl,imx93-aonmix-ns-syscfg", "syscon";
+				reg = <0x44210000 0x1000>;
+			};
+
+			mu1: mailbox@44230000 {
+				compatible = "fsl,imx93-mu", "fsl,imx8ulp-mu";
+				reg = <0x44230000 0x10000>;
+				interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
+				#mbox-cells = <2>;
+				status = "disabled";
+			};
+
+			system_counter: timer@44290000 {
+				compatible = "nxp,sysctr-timer";
+				reg = <0x44290000 0x30000>;
+				interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&osc_24m>;
+				clock-names = "per";
+			};
+
+			lpi2c1: i2c@44340000 {
+				compatible = "fsl,imx93-lpi2c", "fsl,imx7ulp-lpi2c";
+				reg = <0x44340000 0x10000>;
+				interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clk IMX93_CLK_LPI2C1_GATE>,
+					 <&clk IMX93_CLK_BUS_AON>;
+				clock-names = "per", "ipg";
+				status = "disabled";
+			};
+
+			lpi2c2: i2c@44350000 {
+				compatible = "fsl,imx93-lpi2c", "fsl,imx7ulp-lpi2c";
+				reg = <0x44350000 0x10000>;
+				interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clk IMX93_CLK_LPI2C2_GATE>,
+					 <&clk IMX93_CLK_BUS_AON>;
+				clock-names = "per", "ipg";
+				status = "disabled";
+			};
+
+			lpspi1: spi@44360000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "fsl,imx93-spi", "fsl,imx7ulp-spi";
+				reg = <0x44360000 0x10000>;
+				interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clk IMX93_CLK_LPSPI1_GATE>,
+					 <&clk IMX93_CLK_BUS_AON>;
+				clock-names = "per", "ipg";
+				status = "disabled";
+			};
+
+			lpspi2: spi@44370000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "fsl,imx93-spi", "fsl,imx7ulp-spi";
+				reg = <0x44370000 0x10000>;
+				interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clk IMX93_CLK_LPSPI2_GATE>,
+					 <&clk IMX93_CLK_BUS_AON>;
+				clock-names = "per", "ipg";
+				status = "disabled";
+			};
+
+			lpuart1: serial@44380000 {
+				compatible = "fsl,imx93-lpuart", "fsl,imx7ulp-lpuart";
+				reg = <0x44380000 0x1000>;
+				interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clk IMX93_CLK_LPUART1_GATE>;
+				clock-names = "ipg";
+				status = "disabled";
+			};
+
+			lpuart2: serial@44390000 {
+				compatible = "fsl,imx93-lpuart", "fsl,imx7ulp-lpuart";
+				reg = <0x44390000 0x1000>;
+				interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clk IMX93_CLK_LPUART2_GATE>;
+				clock-names = "ipg";
+				status = "disabled";
+			};
+
+			iomuxc: pinctrl@443c0000 {
+				compatible = "fsl,imx93-iomuxc";
+				reg = <0x443c0000 0x10000>;
+				status = "okay";
+			};
+
+			clk: clock-controller@44450000 {
+				compatible = "fsl,imx93-ccm";
+				reg = <0x44450000 0x10000>;
+				#clock-cells = <1>;
+				clocks = <&osc_32k>, <&osc_24m>, <&clk_ext1>;
+				clock-names = "osc_32k", "osc_24m", "clk_ext1";
+				status = "okay";
+			};
+
+			src: system-controller@44460000 {
+				compatible = "fsl,imx93-src", "syscon";
+				reg = <0x44460000 0x10000>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges;
+
+				mediamix: power-domain@44462400 {
+					compatible = "fsl,imx93-src-slice";
+					reg = <0x44462400 0x400>, <0x44465800 0x400>;
+					#power-domain-cells = <0>;
+					clocks = <&clk IMX93_CLK_MEDIA_AXI>,
+						 <&clk IMX93_CLK_MEDIA_APB>;
+				};
+
+				mlmix: power-domain@44461800 {
+					compatible = "fsl,imx93-src-slice";
+					reg = <0x44461800 0x400>, <0x44464800 0x400>;
+					#power-domain-cells = <0>;
+					clocks = <&clk IMX93_CLK_ML_APB>,
+						 <&clk IMX93_CLK_ML>;
+				};
+			};
+
+			anatop: anatop@44480000 {
+				compatible = "fsl,imx93-anatop", "syscon";
+				reg = <0x44480000 0x10000>;
+			};
+		};
+
+		aips2: bus@42000000 {
+			compatible = "fsl,aips-bus", "simple-bus";
+			reg = <0x42000000 0x800000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			wakeupmix_gpr: syscon@42420000 {
+				compatible = "fsl,imx93-wakeupmix-syscfg", "syscon";
+				reg = <0x42420000 0x1000>;
+			};
+
+			mu2: mailbox@42440000 {
+				compatible = "fsl,imx93-mu", "fsl,imx8ulp-mu";
+				reg = <0x42440000 0x10000>;
+				interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
+				#mbox-cells = <2>;
+				status = "disabled";
+			};
+
+			lpi2c3: i2c@42530000 {
+				compatible = "fsl,imx93-lpi2c", "fsl,imx7ulp-lpi2c";
+				reg = <0x42530000 0x10000>;
+				interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clk IMX93_CLK_LPI2C3_GATE>,
+					 <&clk IMX93_CLK_BUS_WAKEUP>;
+				clock-names = "per", "ipg";
+				status = "disabled";
+			};
+
+			lpi2c4: i2c@42540000 {
+				compatible = "fsl,imx93-lpi2c", "fsl,imx7ulp-lpi2c";
+				reg = <0x42540000 0x10000>;
+				interrupts = <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clk IMX93_CLK_LPI2C4_GATE>,
+					 <&clk IMX93_CLK_BUS_WAKEUP>;
+				clock-names = "per", "ipg";
+				status = "disabled";
+			};
+
+			lpuart3: serial@42570000 {
+				compatible = "fsl,imx93-lpuart", "fsl,imx7ulp-lpuart";
+				reg = <0x42570000 0x1000>;
+				interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clk IMX93_CLK_LPUART3_GATE>;
+				clock-names = "ipg";
+				status = "disabled";
+			};
+
+			lpuart4: serial@42580000 {
+				compatible = "fsl,imx93-lpuart", "fsl,imx7ulp-lpuart";
+				reg = <0x42580000 0x1000>;
+				interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clk IMX93_CLK_LPUART4_GATE>;
+				clock-names = "ipg";
+				status = "disabled";
+			};
+
+			lpuart5: serial@42590000 {
+				compatible = "fsl,imx93-lpuart", "fsl,imx7ulp-lpuart";
+				reg = <0x42590000 0x1000>;
+				interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clk IMX93_CLK_LPUART5_GATE>;
+				clock-names = "ipg";
+				status = "disabled";
+			};
+
+			lpuart6: serial@425a0000 {
+				compatible = "fsl,imx93-lpuart", "fsl,imx7ulp-lpuart";
+				reg = <0x425a0000 0x1000>;
+				interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clk IMX93_CLK_LPUART6_GATE>;
+				clock-names = "ipg";
+				status = "disabled";
+			};
+
+			lpuart7: serial@42690000 {
+				compatible = "fsl,imx93-lpuart", "fsl,imx7ulp-lpuart";
+				reg = <0x42690000 0x1000>;
+				interrupts = <GIC_SPI 210 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clk IMX93_CLK_LPUART7_GATE>;
+				clock-names = "ipg";
+				status = "disabled";
+			};
+
+			lpuart8: serial@426a0000 {
+				compatible = "fsl,imx93-lpuart", "fsl,imx7ulp-lpuart";
+				reg = <0x426a0000 0x1000>;
+				interrupts = <GIC_SPI 211 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clk IMX93_CLK_LPUART8_GATE>;
+				clock-names = "ipg";
+				status = "disabled";
+			};
+
+			lpi2c5: i2c@426b0000 {
+				compatible = "fsl,imx93-lpi2c", "fsl,imx7ulp-lpi2c";
+				reg = <0x426b0000 0x10000>;
+				interrupts = <GIC_SPI 195 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clk IMX93_CLK_LPI2C5_GATE>,
+					 <&clk IMX93_CLK_BUS_WAKEUP>;
+				clock-names = "per", "ipg";
+				status = "disabled";
+			};
+
+			lpi2c6: i2c@426c0000 {
+				compatible = "fsl,imx93-lpi2c", "fsl,imx7ulp-lpi2c";
+				reg = <0x426c0000 0x10000>;
+				interrupts = <GIC_SPI 196 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clk IMX93_CLK_LPI2C6_GATE>,
+					 <&clk IMX93_CLK_BUS_WAKEUP>;
+				clock-names = "per", "ipg";
+				status = "disabled";
+			};
+
+			lpi2c7: i2c@426d0000 {
+				compatible = "fsl,imx93-lpi2c", "fsl,imx7ulp-lpi2c";
+				reg = <0x426d0000 0x10000>;
+				interrupts = <GIC_SPI 197 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clk IMX93_CLK_LPI2C7_GATE>,
+					 <&clk IMX93_CLK_BUS_WAKEUP>;
+				clock-names = "per", "ipg";
+				status = "disabled";
+			};
+
+			lpi2c8: i2c@426e0000 {
+				compatible = "fsl,imx93-lpi2c", "fsl,imx7ulp-lpi2c";
+				reg = <0x426e0000 0x10000>;
+				interrupts = <GIC_SPI 198 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clk IMX93_CLK_LPI2C8_GATE>,
+					 <&clk IMX93_CLK_BUS_WAKEUP>;
+				clock-names = "per", "ipg";
+				status = "disabled";
+			};
+
+		};
+
+		aips3: bus@42800000 {
+			compatible = "fsl,aips-bus", "simple-bus";
+			reg = <0x42800000 0x800000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			usdhc1: mmc@42850000 {
+				compatible = "fsl,imx93-usdhc", "fsl,imx8mm-usdhc";
+				reg = <0x42850000 0x10000>;
+				interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clk IMX93_CLK_BUS_WAKEUP>,
+					 <&clk IMX93_CLK_WAKEUP_AXI>,
+					 <&clk IMX93_CLK_USDHC1_GATE>;
+				clock-names = "ipg", "ahb", "per";
+				bus-width = <8>;
+				fsl,tuning-start-tap = <20>;
+				fsl,tuning-step= <2>;
+				status = "disabled";
+			};
+
+			usdhc2: mmc@42860000 {
+				compatible = "fsl,imx93-usdhc", "fsl,imx8mm-usdhc";
+				reg = <0x42860000 0x10000>;
+				interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clk IMX93_CLK_BUS_WAKEUP>,
+					 <&clk IMX93_CLK_WAKEUP_AXI>,
+					 <&clk IMX93_CLK_USDHC2_GATE>;
+				clock-names = "ipg", "ahb", "per";
+				bus-width = <4>;
+				fsl,tuning-start-tap = <20>;
+				fsl,tuning-step= <2>;
+				status = "disabled";
+			};
+
+			usdhc3: mmc@428b0000 {
+				compatible = "fsl,imx93-usdhc", "fsl,imx8mm-usdhc";
+				reg = <0x428b0000 0x10000>;
+				interrupts = <GIC_SPI 205 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clk IMX93_CLK_BUS_WAKEUP>,
+					 <&clk IMX93_CLK_WAKEUP_AXI>,
+					 <&clk IMX93_CLK_USDHC3_GATE>;
+				clock-names = "ipg", "ahb", "per";
+				bus-width = <4>;
+				fsl,tuning-start-tap = <20>;
+				fsl,tuning-step= <2>;
+				status = "disabled";
+			};
+		};
+
+		gpio2: gpio@43810080 {
+			compatible = "fsl,imx93-gpio", "fsl,imx7ulp-gpio";
+			reg = <0x43810080 0x1000>, <0x43810040 0x40>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			clocks = <&clk IMX93_CLK_GPIO2_GATE>,
+				 <&clk IMX93_CLK_GPIO2_GATE>;
+			clock-names = "gpio", "port";
+			gpio-ranges = <&iomuxc 0 4 30>;
+		};
+
+		gpio3: gpio@43820080 {
+			compatible = "fsl,imx93-gpio", "fsl,imx7ulp-gpio";
+			reg = <0x43820080 0x1000>, <0x43820040 0x40>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupts = <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			clocks = <&clk IMX93_CLK_GPIO3_GATE>,
+				 <&clk IMX93_CLK_GPIO3_GATE>;
+			clock-names = "gpio", "port";
+			gpio-ranges = <&iomuxc 0 84 8>, <&iomuxc 8 66 18>,
+				      <&iomuxc 26 34 2>, <&iomuxc 28 0 4>;
+		};
+
+		gpio4: gpio@43830080 {
+			compatible = "fsl,imx93-gpio", "fsl,imx7ulp-gpio";
+			reg = <0x43830080 0x1000>, <0x43830040 0x40>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupts = <GIC_SPI 189 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			clocks = <&clk IMX93_CLK_GPIO4_GATE>,
+				 <&clk IMX93_CLK_GPIO4_GATE>;
+			clock-names = "gpio", "port";
+			gpio-ranges = <&iomuxc 0 38 28>, <&iomuxc 28 36 2>;
+		};
+
+		gpio1: gpio@47400080 {
+			compatible = "fsl,imx93-gpio", "fsl,imx7ulp-gpio";
+			reg = <0x47400080 0x1000>, <0x47400040 0x40>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			clocks = <&clk IMX93_CLK_GPIO1_GATE>,
+				 <&clk IMX93_CLK_GPIO1_GATE>;
+			clock-names = "gpio", "port";
+			gpio-ranges = <&iomuxc 0 92 16>;
+		};
+
+		s4muap: mailbox@47520000 {
+			compatible = "fsl,imx93-mu-s4";
+			reg = <0x47520000 0x10000>;
+			interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "tx", "rx";
+			#mbox-cells = <2>;
+		};
+
+		media_blk_ctrl: system-controller@4ac10000 {
+			compatible = "fsl,imx93-media-blk-ctrl", "syscon";
+			reg = <0x4ac10000 0x10000>;
+			power-domains = <&mediamix>;
+			clocks = <&clk IMX93_CLK_MEDIA_APB>,
+				 <&clk IMX93_CLK_MEDIA_AXI>,
+				 <&clk IMX93_CLK_NIC_MEDIA_GATE>,
+				 <&clk IMX93_CLK_MEDIA_DISP_PIX>,
+				 <&clk IMX93_CLK_CAM_PIX>,
+				 <&clk IMX93_CLK_PXP_GATE>,
+				 <&clk IMX93_CLK_LCDIF_GATE>,
+				 <&clk IMX93_CLK_ISI_GATE>,
+				 <&clk IMX93_CLK_MIPI_CSI_GATE>,
+				 <&clk IMX93_CLK_MIPI_DSI_GATE>;
+			clock-names = "apb", "axi", "nic", "disp", "cam",
+				      "pxp", "lcdif", "isi", "csi", "dsi";
+			#power-domain-cells = <1>;
+			status = "disabled";
+		};
+	};
+};
diff --git a/arch/arm64/boot/dts/freescale/mba8mx.dtsi b/arch/arm64/boot/dts/freescale/mba8mx.dtsi
new file mode 100644
index 000000000000..104bdd4e437a
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/mba8mx.dtsi
@@ -0,0 +1,286 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright 2020-2021 TQ-Systems GmbH
+ */
+
+#include <dt-bindings/net/ti-dp83867.h>
+
+/* TQ-Systems GmbH MBa8Mx baseboard */
+
+/ {
+	beeper {
+		compatible = "pwm-beeper";
+		pwms = <&pwm4 0 250000 0>;
+		beeper-hz = <4000>;
+		amp-supply = <&reg_vcc_3v3>;
+	};
+
+	chosen {
+		stdout-path = &uart3;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpiobutton>;
+		autorepeat;
+
+		switch-1 {
+			label = "switch1";
+			linux,code = <BTN_0>;
+			gpios = <&gpio1 5 GPIO_ACTIVE_LOW>;
+			wakeup-source;
+		};
+
+		btn2: switch-2 {
+			label = "switch2";
+			linux,code = <BTN_1>;
+			gpios = <&gpio2 0 GPIO_ACTIVE_LOW>;
+			wakeup-source;
+		};
+
+		switch-3 {
+			label = "switch3";
+			linux,code = <BTN_2>;
+			gpios = <&gpio1 7 GPIO_ACTIVE_LOW>;
+			wakeup-source;
+		};
+	};
+
+	gpio_leds: gpio-leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpioled>;
+
+		led1 {
+			label = "led1";
+			gpios = <&gpio1 0 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "default-on";
+		};
+
+		led2: led2 {
+			label = "led2";
+			gpios = <&gpio3 14 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	pcie0_refclk: pcie0-refclk {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <100000000>;
+	};
+
+	reg_hub_vbus: regulator-hub-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "MBA8MX_HUB_VBUS";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	reg_sn65dsi83_1v8: regulator-sn65dsi83-1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "SN65DSI83_1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		gpio = <&expander0 5 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	reg_vcc_3v3: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "MBA8MX_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	sound {
+		compatible = "fsl,imx-audio-tlv320aic32x4";
+		model = "imx-audio-tlv320aic32x4";
+		ssi-controller = <&sai3>;
+		audio-codec = <&tlv320aic3x04>;
+	};
+};
+
+&ecspi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1>;
+	cs-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&ecspi2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi2>;
+	cs-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&fec1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_fec1>;
+	phy-mode = "rgmii-id";
+	phy-handle = <&ethphy0>;
+	phy-supply = <&reg_vcc_3v3>;
+	fsl,magic-packet;
+	mac-address = [ 00 00 00 00 00 00 ];
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy0: ethernet-phy@e {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			reg = <0xe>;
+			ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_50_NS>;
+			ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_50_NS>;
+			ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+			ti,dp83867-rxctrl-strap-quirk;
+			ti,clk-output-sel = <DP83867_CLK_O_SEL_OFF>;
+			enet-phy-lane-no-swap;
+			reset-gpios = <&expander2 7 GPIO_ACTIVE_LOW>;
+			reset-assert-us = <500000>;
+			reset-deassert-us = <500>;
+		};
+	};
+};
+
+&i2c1 {
+	expander0: gpio@23 {
+		compatible = "nxp,pca9555";
+		reg = <0x23>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		vcc-supply = <&reg_vcc_3v3>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <9 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+
+		sd-mux-oe-hog {
+			gpio-hog;
+			gpios = <8 0>;
+			output-low;
+			line-name = "SD_MUX_EN#";
+		};
+
+		boot-cfg-oe-hog {
+			gpio-hog;
+			gpios = <12 0>;
+			output-high;
+			line-name = "BOOT_CFG_OE#";
+		};
+
+		rst-usb-hub-hog {
+			gpio-hog;
+			gpios = <13 0>;
+			output-high;
+			line-name = "RST_USB_HUB#";
+		};
+	};
+
+	expander1: gpio@24 {
+		compatible = "nxp,pca9555";
+		reg = <0x24>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		vcc-supply = <&reg_vcc_3v3>;
+	};
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	pinctrl-1 = <&pinctrl_i2c2_gpio>;
+	scl-gpios = <&gpio5 16 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio5 17 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "okay";
+
+	tlv320aic3x04: audio-codec@18 {
+		compatible = "ti,tlv320aic32x4";
+		reg = <0x18>;
+		reset-gpios = <&expander2 0 GPIO_ACTIVE_LOW>;
+		iov-supply = <&reg_vcc_3v3>;
+		ldoin-supply = <&reg_vcc_3v3>;
+	};
+
+	sensor1: sensor@1f {
+		compatible = "nxp,se97", "jedec,jc-42.4-temp";
+		reg = <0x1f>;
+	};
+
+	eeprom3: eeprom@57 {
+		compatible = "nxp,se97b", "atmel,24c02";
+		reg = <0x57>;
+		pagesize = <16>;
+	};
+};
+
+&i2c3 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default", "gpio";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	pinctrl-1 = <&pinctrl_i2c3_gpio>;
+	scl-gpios = <&gpio5 18 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio5 19 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	status = "okay";
+};
+
+&pwm3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm3>;
+	status = "okay";
+};
+
+&pwm4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm4>;
+	status = "okay";
+};
+
+&sai3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_sai3>;
+	#sound-dai-cells = <0>;
+	assigned-clock-rates = <49152000>;
+	status = "okay";
+};
+
+&snvs_pwrkey {
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	status = "okay";
+};
+
+/* console */
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	status = "okay";
+};
+
+&usdhc2 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>;
+	pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>;
+	pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>;
+	bus-width = <4>;
+	cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
+	disable-wp;
+	no-mmc;
+	no-sdio;
+	vmmc-supply = <&reg_usdhc2_vmmc>;
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/freescale/s32g2.dtsi b/arch/arm64/boot/dts/freescale/s32g2.dtsi
index 59ea8a25aa4c..824d401e7a2c 100644
--- a/arch/arm64/boot/dts/freescale/s32g2.dtsi
+++ b/arch/arm64/boot/dts/freescale/s32g2.dtsi
@@ -79,7 +79,7 @@
 		};
 	};
 
-	soc {
+	soc@0 {
 		compatible = "simple-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
diff --git a/arch/arm64/boot/dts/hisilicon/hi3660-hikey960.dts b/arch/arm64/boot/dts/hisilicon/hi3660-hikey960.dts
index f68580dc87d8..0192a01bf852 100644
--- a/arch/arm64/boot/dts/hisilicon/hi3660-hikey960.dts
+++ b/arch/arm64/boot/dts/hisilicon/hi3660-hikey960.dts
@@ -49,9 +49,9 @@
 		ramoops@32000000 {
 			compatible = "ramoops";
 			reg = <0x0 0x32000000 0x0 0x00100000>;
-			record-size	= <0x00020000>;
-			console-size	= <0x00020000>;
-			ftrace-size	= <0x00020000>;
+			record-size = <0x00020000>;
+			console-size = <0x00020000>;
+			ftrace-size = <0x00020000>;
 		};
 	};
 
@@ -63,9 +63,9 @@
 			compatible = "syscon-reboot-mode";
 			offset = <0x0>;
 
-			mode-normal	= <0x77665501>;
-			mode-bootloader	= <0x77665500>;
-			mode-recovery	= <0x77665502>;
+			mode-normal = <0x77665501>;
+			mode-bootloader = <0x77665500>;
+			mode-recovery = <0x77665502>;
 		};
 	};
 
@@ -74,7 +74,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pwr_key_pmx_func &pwr_key_cfg_func>;
 
-		power {
+		key-power {
 			wakeup-source;
 			gpios = <&gpio4 2 GPIO_ACTIVE_LOW>;
 			label = "GPIO Power";
diff --git a/arch/arm64/boot/dts/hisilicon/hi3660.dtsi b/arch/arm64/boot/dts/hisilicon/hi3660.dtsi
index 8bd6d7e8a474..8343d0cedde3 100644
--- a/arch/arm64/boot/dts/hisilicon/hi3660.dtsi
+++ b/arch/arm64/boot/dts/hisilicon/hi3660.dtsi
@@ -479,7 +479,7 @@
 			reg = <0x0 0xfdf00000 0x0 0x1000>;
 			interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
 			dma-names = "rx", "tx";
-			dmas =  <&dma0 2 &dma0 3>;
+			dmas = <&dma0 2 &dma0 3>;
 			clocks = <&crg_ctrl HI3660_CLK_GATE_UART1>,
 				 <&crg_ctrl HI3660_CLK_GATE_UART1>;
 			clock-names = "uartclk", "apb_pclk";
@@ -493,7 +493,7 @@
 			reg = <0x0 0xfdf03000 0x0 0x1000>;
 			interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
 			dma-names = "rx", "tx";
-			dmas =  <&dma0 4 &dma0 5>;
+			dmas = <&dma0 4 &dma0 5>;
 			clocks = <&crg_ctrl HI3660_CLK_GATE_UART2>,
 				 <&crg_ctrl HI3660_PCLK>;
 			clock-names = "uartclk", "apb_pclk";
@@ -519,7 +519,7 @@
 			reg = <0x0 0xfdf01000 0x0 0x1000>;
 			interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
 			dma-names = "rx", "tx";
-			dmas =  <&dma0 6 &dma0 7>;
+			dmas = <&dma0 6 &dma0 7>;
 			clocks = <&crg_ctrl HI3660_CLK_GATE_UART4>,
 				 <&crg_ctrl HI3660_CLK_GATE_UART4>;
 			clock-names = "uartclk", "apb_pclk";
@@ -533,7 +533,7 @@
 			reg = <0x0 0xfdf05000 0x0 0x1000>;
 			interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
 			dma-names = "rx", "tx";
-			dmas =  <&dma0 8 &dma0 9>;
+			dmas = <&dma0 8 &dma0 9>;
 			clocks = <&crg_ctrl HI3660_CLK_GATE_UART5>,
 				 <&crg_ctrl HI3660_CLK_GATE_UART5>;
 			clock-names = "uartclk", "apb_pclk";
@@ -1045,8 +1045,8 @@
 			clocks = <&crg_ctrl HI3660_CLK_GATE_UFSIO_REF>,
 				<&crg_ctrl HI3660_CLK_GATE_UFSPHY_CFG>;
 			clock-names = "ref_clk", "phy_clk";
-			freq-table-hz = <0 0
-					 0 0>;
+			freq-table-hz = <0 0>,
+					<0 0>;
 			/* offset: 0x84; bit: 12 */
 			resets = <&crg_rst 0x84 12>;
 			reset-names = "rst";
diff --git a/arch/arm64/boot/dts/hisilicon/hi3670.dtsi b/arch/arm64/boot/dts/hisilicon/hi3670.dtsi
index 636c8817df7e..886b93c5893a 100644
--- a/arch/arm64/boot/dts/hisilicon/hi3670.dtsi
+++ b/arch/arm64/boot/dts/hisilicon/hi3670.dtsi
@@ -324,7 +324,7 @@
 			interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
 			gpio-controller;
 			#gpio-cells = <2>;
-			gpio-ranges =  <&pmx0 0 13 4 &pmx0 7 17 1>;
+			gpio-ranges = <&pmx0 0 13 4 &pmx0 7 17 1>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
 			clocks = <&crg_ctrl HI3670_PCLK_GPIO3>;
@@ -671,8 +671,8 @@
 			clocks = <&crg_ctrl HI3670_CLK_GATE_UFSIO_REF>,
 				 <&crg_ctrl HI3670_CLK_GATE_UFS_SUBSYS>;
 			clock-names = "ref_clk", "phy_clk";
-			freq-table-hz = <0 0
-					 0 0>;
+			freq-table-hz = <0 0>,
+					<0 0>;
 			/* offset: 0x84; bit: 12 */
 			resets = <&crg_rst 0x84 12>;
 			reset-names = "rst";
diff --git a/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts b/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
index 3df2afb2f637..629e604aa281 100644
--- a/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
+++ b/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
@@ -54,9 +54,9 @@
 		ramoops@21f00000 {
 			compatible = "ramoops";
 			reg = <0x0 0x21f00000 0x0 0x00100000>;
-			record-size	= <0x00020000>;
-			console-size	= <0x00020000>;
-			ftrace-size	= <0x00020000>;
+			record-size = <0x00020000>;
+			console-size = <0x00020000>;
+			ftrace-size = <0x00020000>;
 		};
 
 		/* global autoconfigured region for contiguous allocations */
@@ -76,9 +76,9 @@
 			compatible = "syscon-reboot-mode";
 			offset = <0x0>;
 
-			mode-normal	= <0x77665501>;
-			mode-bootloader	= <0x77665500>;
-			mode-recovery	= <0x77665502>;
+			mode-normal = <0x77665501>;
+			mode-bootloader = <0x77665500>;
+			mode-recovery = <0x77665502>;
 		};
 	};
 
diff --git a/arch/arm64/boot/dts/hisilicon/hip05-d02.dts b/arch/arm64/boot/dts/hisilicon/hip05-d02.dts
index 40f3e00ac832..c4eaebbb448f 100644
--- a/arch/arm64/boot/dts/hisilicon/hip05-d02.dts
+++ b/arch/arm64/boot/dts/hisilicon/hip05-d02.dts
@@ -27,12 +27,10 @@
 		stdout-path = "serial0:115200n8";
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 
-		pwrbutton {
+		pwr-button {
 			label = "Power Button";
 			gpios = <&porta 8 GPIO_ACTIVE_LOW>;
 			linux,code = <116>;
diff --git a/arch/arm64/boot/dts/hisilicon/hip06.dtsi b/arch/arm64/boot/dts/hisilicon/hip06.dtsi
index 70d7732dd348..2f8b03b0d365 100644
--- a/arch/arm64/boot/dts/hisilicon/hip06.dtsi
+++ b/arch/arm64/boot/dts/hisilicon/hip06.dtsi
@@ -537,7 +537,7 @@
 
 			port@1 {
 				reg = <1>;
-				serdes-syscon= <&serdes_ctrl>;
+				serdes-syscon = <&serdes_ctrl>;
 				port-rst-offset = <1>;
 				port-mode-offset = <1>;
 				media-type = "fiber";
@@ -546,7 +546,7 @@
 			port@4 {
 				reg = <4>;
 				phy-handle = <&phy0>;
-				serdes-syscon= <&serdes_ctrl>;
+				serdes-syscon = <&serdes_ctrl>;
 				port-rst-offset = <4>;
 				port-mode-offset = <2>;
 				media-type = "copper";
@@ -555,7 +555,7 @@
 			port@5 {
 				reg = <5>;
 				phy-handle = <&phy1>;
-				serdes-syscon= <&serdes_ctrl>;
+				serdes-syscon = <&serdes_ctrl>;
 				port-rst-offset = <5>;
 				port-mode-offset = <3>;
 				media-type = "copper";
diff --git a/arch/arm64/boot/dts/hisilicon/hip07.dtsi b/arch/arm64/boot/dts/hisilicon/hip07.dtsi
index 6baf6a686450..1a16662f8867 100644
--- a/arch/arm64/boot/dts/hisilicon/hip07.dtsi
+++ b/arch/arm64/boot/dts/hisilicon/hip07.dtsi
@@ -1422,7 +1422,7 @@
 
 			port@1 {
 				reg = <1>;
-				serdes-syscon= <&serdes_ctrl>;
+				serdes-syscon = <&serdes_ctrl>;
 				cpld-syscon = <&dsa_cpld 0x4>;
 				port-rst-offset = <1>;
 				port-mode-offset = <1>;
@@ -1433,7 +1433,7 @@
 			port@4 {
 				reg = <4>;
 				phy-handle = <&phy0>;
-				serdes-syscon= <&serdes_ctrl>;
+				serdes-syscon = <&serdes_ctrl>;
 				port-rst-offset = <4>;
 				port-mode-offset = <2>;
 				mc-mac-mask = [ff f0 00 00 00 00];
@@ -1443,7 +1443,7 @@
 			port@5 {
 				reg = <5>;
 				phy-handle = <&phy1>;
-				serdes-syscon= <&serdes_ctrl>;
+				serdes-syscon = <&serdes_ctrl>;
 				port-rst-offset = <5>;
 				port-mode-offset = <3>;
 				mc-mac-mask = [ff f0 00 00 00 00];
diff --git a/arch/arm64/boot/dts/intel/Makefile b/arch/arm64/boot/dts/intel/Makefile
index 0b5477442263..c2a723838344 100644
--- a/arch/arm64/boot/dts/intel/Makefile
+++ b/arch/arm64/boot/dts/intel/Makefile
@@ -1,5 +1,6 @@
 # SPDX-License-Identifier: GPL-2.0-only
-dtb-$(CONFIG_ARCH_INTEL_SOCFPGA) += socfpga_agilex_socdk.dtb \
+dtb-$(CONFIG_ARCH_INTEL_SOCFPGA) += socfpga_agilex_n6000.dtb \
+				socfpga_agilex_socdk.dtb \
 				socfpga_agilex_socdk_nand.dtb \
 				socfpga_n5x_socdk.dtb
 dtb-$(CONFIG_ARCH_KEEMBAY) += keembay-evm.dtb
diff --git a/arch/arm64/boot/dts/intel/socfpga_agilex.dtsi b/arch/arm64/boot/dts/intel/socfpga_agilex.dtsi
index 163f33b46e4f..7bbec8aafa62 100644
--- a/arch/arm64/boot/dts/intel/socfpga_agilex.dtsi
+++ b/arch/arm64/boot/dts/intel/socfpga_agilex.dtsi
@@ -300,7 +300,7 @@
 			status = "disabled";
 		};
 
-		mmc: dwmmc0@ff808000 {
+		mmc: mmc@ff808000 {
 			#address-cells = <1>;
 			#size-cells = <0>;
 			compatible = "altr,socfpga-dw-mshc";
@@ -337,7 +337,7 @@
 			reg = <0xffe00000 0x40000>;
 		};
 
-		pdma: pdma@ffda0000 {
+		pdma: dma-controller@ffda0000 {
 			compatible = "arm,pl330", "arm,primecell";
 			reg = <0xffda0000 0x1000>;
 			interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>,
@@ -350,8 +350,6 @@
 				     <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
 			#dma-cells = <1>;
-			#dma-channels = <8>;
-			#dma-requests = <32>;
 			resets = <&rst DMA_RESET>, <&rst DMA_OCP_RESET>;
 			reset-names = "dma", "dma-ocp";
 			clocks = <&clkmgr AGILEX_L4_MAIN_CLK>;
@@ -502,7 +500,7 @@
 		};
 
 		usb0: usb@ffb00000 {
-			compatible = "snps,dwc2";
+			compatible = "intel,socfpga-agilex-hsotg", "snps,dwc2";
 			reg = <0xffb00000 0x40000>;
 			interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>;
 			phys = <&usbphy0>;
@@ -510,12 +508,13 @@
 			resets = <&rst USB0_RESET>, <&rst USB0_OCP_RESET>;
 			reset-names = "dwc2", "dwc2-ecc";
 			clocks = <&clkmgr AGILEX_USB_CLK>;
+			clock-names = "otg";
 			iommus = <&smmu 6>;
 			status = "disabled";
 		};
 
 		usb1: usb@ffb40000 {
-			compatible = "snps,dwc2";
+			compatible = "intel,socfpga-agilex-hsotg", "snps,dwc2";
 			reg = <0xffb40000 0x40000>;
 			interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>;
 			phys = <&usbphy0>;
@@ -582,7 +581,7 @@
 			sdramedac {
 				compatible = "altr,sdram-edac-s10";
 				altr,sdr-syscon = <&sdr>;
-				interrupts = <16 4>;
+				interrupts = <16 IRQ_TYPE_LEVEL_HIGH>;
 			};
 
 			ocram-ecc@ff8cc000 {
@@ -590,7 +589,7 @@
 					     "altr,socfpga-a10-ocram-ecc";
 				reg = <0xff8cc000 0x100>;
 				altr,ecc-parent = <&ocram>;
-				interrupts = <1 4>;
+				interrupts = <1 IRQ_TYPE_LEVEL_HIGH>;
 			};
 
 			usb0-ecc@ff8c4000 {
@@ -598,7 +597,7 @@
 					     "altr,socfpga-usb-ecc";
 				reg = <0xff8c4000 0x100>;
 				altr,ecc-parent = <&usb0>;
-				interrupts = <2 4>;
+				interrupts = <2 IRQ_TYPE_LEVEL_HIGH>;
 			};
 
 			emac0-rx-ecc@ff8c0000 {
@@ -606,7 +605,7 @@
 					     "altr,socfpga-eth-mac-ecc";
 				reg = <0xff8c0000 0x100>;
 				altr,ecc-parent = <&gmac0>;
-				interrupts = <4 4>;
+				interrupts = <4 IRQ_TYPE_LEVEL_HIGH>;
 			};
 
 			emac0-tx-ecc@ff8c0400 {
@@ -614,7 +613,7 @@
 					     "altr,socfpga-eth-mac-ecc";
 				reg = <0xff8c0400 0x100>;
 				altr,ecc-parent = <&gmac0>;
-				interrupts = <5 4>;
+				interrupts = <5 IRQ_TYPE_LEVEL_HIGH>;
 			};
 
 			sdmmca-ecc@ff8c8c00 {
@@ -622,13 +621,13 @@
 					     "altr,socfpga-sdmmc-ecc";
 				reg = <0xff8c8c00 0x100>;
 				altr,ecc-parent = <&mmc>;
-				interrupts = <14 4>,
-					     <15 4>;
+				interrupts = <14 IRQ_TYPE_LEVEL_HIGH>,
+					     <15 IRQ_TYPE_LEVEL_HIGH>;
 			};
 		};
 
 		qspi: spi@ff8d2000 {
-			compatible = "cdns,qspi-nor";
+			compatible = "intel,socfpga-qspi", "cdns,qspi-nor";
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <0xff8d2000 0x100>,
diff --git a/arch/arm64/boot/dts/intel/socfpga_agilex_n6000.dts b/arch/arm64/boot/dts/intel/socfpga_agilex_n6000.dts
new file mode 100644
index 000000000000..6231a69204b1
--- /dev/null
+++ b/arch/arm64/boot/dts/intel/socfpga_agilex_n6000.dts
@@ -0,0 +1,66 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2021-2022, Intel Corporation
+ */
+#include "socfpga_agilex.dtsi"
+
+/ {
+	model = "SoCFPGA Agilex n6000";
+	compatible = "intel,socfpga-agilex-n6000", "intel,socfpga-agilex";
+
+	aliases {
+		serial0 = &uart1;
+		serial1 = &uart0;
+		ethernet0 = &gmac0;
+		ethernet1 = &gmac1;
+		ethernet2 = &gmac2;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		/* We expect the bootloader to fill in the reg */
+		reg = <0 0 0 0>;
+	};
+
+	soc {
+		bus@80000000 {
+			compatible = "simple-bus";
+			reg = <0x80000000 0x60000000>,
+				<0xf9000000 0x00100000>;
+			reg-names = "axi_h2f", "axi_h2f_lw";
+			#address-cells = <2>;
+			#size-cells = <1>;
+			ranges = <0x00000000 0x00000000 0xf9000000 0x00001000>;
+
+			dma-controller@0 {
+				compatible = "intel,hps-copy-engine";
+				reg = <0x00000000 0x00000000 0x00001000>;
+				#dma-cells = <1>;
+			};
+		};
+	};
+};
+
+&osc1 {
+	clock-frequency = <25000000>;
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&watchdog0 {
+	status = "okay";
+};
+
+&fpga_mgr {
+	status = "disabled";
+};
diff --git a/arch/arm64/boot/dts/intel/socfpga_agilex_socdk.dts b/arch/arm64/boot/dts/intel/socfpga_agilex_socdk.dts
index 0f7a0ba344be..26cd3c121757 100644
--- a/arch/arm64/boot/dts/intel/socfpga_agilex_socdk.dts
+++ b/arch/arm64/boot/dts/intel/socfpga_agilex_socdk.dts
@@ -6,6 +6,7 @@
 
 / {
 	model = "SoCFPGA Agilex SoCDK";
+	compatible = "intel,socfpga-agilex-socdk", "intel,socfpga-agilex";
 
 	aliases {
 		serial0 = &uart0;
@@ -20,17 +21,17 @@
 
 	leds {
 		compatible = "gpio-leds";
-		hps0 {
+		led0 {
 			label = "hps_led0";
 			gpios = <&portb 20 GPIO_ACTIVE_HIGH>;
 		};
 
-		hps1 {
+		led1 {
 			label = "hps_led1";
 			gpios = <&portb 19 GPIO_ACTIVE_HIGH>;
 		};
 
-		hps2 {
+		led2 {
 			label = "hps_led2";
 			gpios = <&portb 21 GPIO_ACTIVE_HIGH>;
 		};
diff --git a/arch/arm64/boot/dts/intel/socfpga_agilex_socdk_nand.dts b/arch/arm64/boot/dts/intel/socfpga_agilex_socdk_nand.dts
index cc2dcabf34e3..51f83f96ec65 100644
--- a/arch/arm64/boot/dts/intel/socfpga_agilex_socdk_nand.dts
+++ b/arch/arm64/boot/dts/intel/socfpga_agilex_socdk_nand.dts
@@ -6,6 +6,7 @@
 
 / {
 	model = "SoCFPGA Agilex SoCDK";
+	compatible = "intel,socfpga-agilex-socdk", "intel,socfpga-agilex";
 
 	aliases {
 		serial0 = &uart0;
@@ -91,24 +92,8 @@
 			reg = <0 0x200000>;
 		};
 		partition@200000 {
-			label = "env";
-			reg = <0x200000 0x40000>;
-		};
-		partition@240000 {
-			label = "dtb";
-			reg = <0x240000 0x40000>;
-		};
-		partition@280000 {
-			label = "kernel";
-			reg = <0x280000 0x2000000>;
-		};
-		partition@2280000 {
-			label = "misc";
-			reg = <0x2280000 0x2000000>;
-		};
-		partition@4280000 {
-			label = "rootfs";
-			reg = <0x4280000 0x3bd80000>;
+			label = "root";
+			reg = <0x200000 0x3fe00000>;
 		};
 	};
 };
diff --git a/arch/arm64/boot/dts/intel/socfpga_n5x_socdk.dts b/arch/arm64/boot/dts/intel/socfpga_n5x_socdk.dts
index 01f1307ce4ac..62c66e52b656 100644
--- a/arch/arm64/boot/dts/intel/socfpga_n5x_socdk.dts
+++ b/arch/arm64/boot/dts/intel/socfpga_n5x_socdk.dts
@@ -6,6 +6,7 @@
 
 / {
 	model = "eASIC N5X SoCDK";
+	compatible = "intel,n5x-socdk", "intel,socfpga-agilex";
 
 	aliases {
 		serial0 = &uart0;
@@ -23,12 +24,51 @@
 		/* We expect the bootloader to fill in the reg */
 		reg = <0 0 0 0>;
 	};
+
+	soc {
+		sdram_edac: memory-controller@f87f8000 {
+			compatible = "snps,ddrc-3.80a";
+			reg = <0xf87f8000 0x400>;
+			interrupts = <0 175 4>;
+			status = "okay";
+		};
+	};
 };
 
 &clkmgr {
 	compatible = "intel,easic-n5x-clkmgr";
 };
 
+&gmac0 {
+	status = "okay";
+	phy-mode = "rgmii";
+	phy-handle = <&phy0>;
+
+	max-frame-size = <9000>;
+
+	mdio0 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+		phy0: ethernet-phy@0 {
+			reg = <4>;
+
+			txd0-skew-ps = <0>; /* -420ps */
+			txd1-skew-ps = <0>; /* -420ps */
+			txd2-skew-ps = <0>; /* -420ps */
+			txd3-skew-ps = <0>; /* -420ps */
+			rxd0-skew-ps = <420>; /* 0ps */
+			rxd1-skew-ps = <420>; /* 0ps */
+			rxd2-skew-ps = <420>; /* 0ps */
+			rxd3-skew-ps = <420>; /* 0ps */
+			txen-skew-ps = <0>; /* -420ps */
+			txc-skew-ps = <900>; /* 0ps */
+			rxdv-skew-ps = <420>; /* 0ps */
+			rxc-skew-ps = <1680>; /* 780ps */
+		};
+	};
+};
+
 &mmc {
 	status = "okay";
 	cap-sd-highspeed;
@@ -40,10 +80,51 @@
 	clock-frequency = <25000000>;
 };
 
+&qspi {
+	status = "okay";
+	flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "micron,mt25qu02g", "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <100000000>;
+
+		m25p,fast-read;
+		cdns,page-size = <256>;
+		cdns,block-size = <16>;
+		cdns,read-delay = <2>;
+		cdns,tshsl-ns = <50>;
+		cdns,tsd2d-ns = <50>;
+		cdns,tchsh-ns = <4>;
+		cdns,tslch-ns = <4>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			qspi_boot: partition@0 {
+				label = "Boot and fpga data";
+				reg = <0x0 0x03FE0000>;
+			};
+
+			qspi_rootfs: partition@3FE0000 {
+				label = "Root Filesystem - JFFS2";
+				reg = <0x03FE0000 0x0C020000>;
+			};
+		};
+	};
+};
+
 &uart0 {
 	status = "okay";
 };
 
+&usb0 {
+	status = "okay";
+	disable-over-current;
+};
+
 &watchdog0 {
 	status = "okay";
 };
diff --git a/arch/arm64/boot/dts/lg/lg1312.dtsi b/arch/arm64/boot/dts/lg/lg1312.dtsi
index 081fe7a9f605..78ae73d0cf36 100644
--- a/arch/arm64/boot/dts/lg/lg1312.dtsi
+++ b/arch/arm64/boot/dts/lg/lg1312.dtsi
@@ -52,7 +52,7 @@
 	};
 
 	psci {
-		compatible  = "arm,psci-0.2", "arm,psci";
+		compatible = "arm,psci-0.2", "arm,psci";
 		method = "smc";
 		cpu_suspend = <0x84000001>;
 		cpu_off = <0x84000002>;
@@ -150,7 +150,7 @@
 			interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&clk_bus>;
 			clock-names = "apb_pclk";
-			status="disabled";
+			status = "disabled";
 		};
 		uart1: serial@fe100000 {
 			compatible = "arm,pl011", "arm,primecell";
@@ -158,7 +158,7 @@
 			interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&clk_bus>;
 			clock-names = "apb_pclk";
-			status="disabled";
+			status = "disabled";
 		};
 		uart2: serial@fe200000 {
 			compatible = "arm,pl011", "arm,primecell";
@@ -166,7 +166,7 @@
 			interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&clk_bus>;
 			clock-names = "apb_pclk";
-			status="disabled";
+			status = "disabled";
 		};
 		spi0: spi@fe800000 {
 			compatible = "arm,pl022", "arm,primecell";
@@ -182,12 +182,13 @@
 			clocks = <&clk_bus>;
 			clock-names = "apb_pclk";
 		};
-		dmac0: dma@c1128000 {
+		dmac0: dma-controller@c1128000 {
 			compatible = "arm,pl330", "arm,primecell";
 			reg = <0x0 0xc1128000 0x1000>;
 			interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&clk_bus>;
 			clock-names = "apb_pclk";
+			#dma-cells = <1>;
 		};
 		gpio0: gpio@fd400000 {
 			#gpio-cells = <2>;
@@ -196,7 +197,7 @@
 			reg = <0x0 0xfd400000 0x1000>;
 			clocks = <&clk_bus>;
 			clock-names = "apb_pclk";
-			status="disabled";
+			status = "disabled";
 		};
 		gpio1: gpio@fd410000 {
 			#gpio-cells = <2>;
@@ -205,7 +206,7 @@
 			reg = <0x0 0xfd410000 0x1000>;
 			clocks = <&clk_bus>;
 			clock-names = "apb_pclk";
-			status="disabled";
+			status = "disabled";
 		};
 		gpio2: gpio@fd420000 {
 			#gpio-cells = <2>;
@@ -214,7 +215,7 @@
 			reg = <0x0 0xfd420000 0x1000>;
 			clocks = <&clk_bus>;
 			clock-names = "apb_pclk";
-			status="disabled";
+			status = "disabled";
 		};
 		gpio3: gpio@fd430000 {
 			#gpio-cells = <2>;
@@ -231,7 +232,7 @@
 			reg = <0x0 0xfd440000 0x1000>;
 			clocks = <&clk_bus>;
 			clock-names = "apb_pclk";
-			status="disabled";
+			status = "disabled";
 		};
 		gpio5: gpio@fd450000 {
 			#gpio-cells = <2>;
@@ -240,7 +241,7 @@
 			reg = <0x0 0xfd450000 0x1000>;
 			clocks = <&clk_bus>;
 			clock-names = "apb_pclk";
-			status="disabled";
+			status = "disabled";
 		};
 		gpio6: gpio@fd460000 {
 			#gpio-cells = <2>;
@@ -249,7 +250,7 @@
 			reg = <0x0 0xfd460000 0x1000>;
 			clocks = <&clk_bus>;
 			clock-names = "apb_pclk";
-			status="disabled";
+			status = "disabled";
 		};
 		gpio7: gpio@fd470000 {
 			#gpio-cells = <2>;
@@ -258,7 +259,7 @@
 			reg = <0x0 0xfd470000 0x1000>;
 			clocks = <&clk_bus>;
 			clock-names = "apb_pclk";
-			status="disabled";
+			status = "disabled";
 		};
 		gpio8: gpio@fd480000 {
 			#gpio-cells = <2>;
@@ -267,7 +268,7 @@
 			reg = <0x0 0xfd480000 0x1000>;
 			clocks = <&clk_bus>;
 			clock-names = "apb_pclk";
-			status="disabled";
+			status = "disabled";
 		};
 		gpio9: gpio@fd490000 {
 			#gpio-cells = <2>;
@@ -276,7 +277,7 @@
 			reg = <0x0 0xfd490000 0x1000>;
 			clocks = <&clk_bus>;
 			clock-names = "apb_pclk";
-			status="disabled";
+			status = "disabled";
 		};
 		gpio10: gpio@fd4a0000 {
 			#gpio-cells = <2>;
@@ -285,7 +286,7 @@
 			reg = <0x0 0xfd4a0000 0x1000>;
 			clocks = <&clk_bus>;
 			clock-names = "apb_pclk";
-			status="disabled";
+			status = "disabled";
 		};
 		gpio11: gpio@fd4b0000 {
 			#gpio-cells = <2>;
@@ -302,7 +303,7 @@
 			reg = <0x0 0xfd4c0000 0x1000>;
 			clocks = <&clk_bus>;
 			clock-names = "apb_pclk";
-			status="disabled";
+			status = "disabled";
 		};
 		gpio13: gpio@fd4d0000 {
 			#gpio-cells = <2>;
@@ -311,7 +312,7 @@
 			reg = <0x0 0xfd4d0000 0x1000>;
 			clocks = <&clk_bus>;
 			clock-names = "apb_pclk";
-			status="disabled";
+			status = "disabled";
 		};
 		gpio14: gpio@fd4e0000 {
 			#gpio-cells = <2>;
@@ -320,7 +321,7 @@
 			reg = <0x0 0xfd4e0000 0x1000>;
 			clocks = <&clk_bus>;
 			clock-names = "apb_pclk";
-			status="disabled";
+			status = "disabled";
 		};
 		gpio15: gpio@fd4f0000 {
 			#gpio-cells = <2>;
@@ -329,7 +330,7 @@
 			reg = <0x0 0xfd4f0000 0x1000>;
 			clocks = <&clk_bus>;
 			clock-names = "apb_pclk";
-			status="disabled";
+			status = "disabled";
 		};
 		gpio16: gpio@fd500000 {
 			#gpio-cells = <2>;
@@ -338,7 +339,7 @@
 			reg = <0x0 0xfd500000 0x1000>;
 			clocks = <&clk_bus>;
 			clock-names = "apb_pclk";
-			status="disabled";
+			status = "disabled";
 		};
 		gpio17: gpio@fd510000 {
 			#gpio-cells = <2>;
diff --git a/arch/arm64/boot/dts/lg/lg1313.dtsi b/arch/arm64/boot/dts/lg/lg1313.dtsi
index 604bb6975337..2173316573be 100644
--- a/arch/arm64/boot/dts/lg/lg1313.dtsi
+++ b/arch/arm64/boot/dts/lg/lg1313.dtsi
@@ -52,7 +52,7 @@
 	};
 
 	psci {
-		compatible  = "arm,psci-0.2", "arm,psci";
+		compatible = "arm,psci-0.2", "arm,psci";
 		method = "smc";
 		cpu_suspend = <0x84000001>;
 		cpu_off = <0x84000002>;
@@ -150,7 +150,7 @@
 			interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&clk_bus>;
 			clock-names = "apb_pclk";
-			status="disabled";
+			status = "disabled";
 		};
 		uart1: serial@fe100000 {
 			compatible = "arm,pl011", "arm,primecell";
@@ -158,7 +158,7 @@
 			interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&clk_bus>;
 			clock-names = "apb_pclk";
-			status="disabled";
+			status = "disabled";
 		};
 		uart2: serial@fe200000 {
 			compatible = "arm,pl011", "arm,primecell";
@@ -166,7 +166,7 @@
 			interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&clk_bus>;
 			clock-names = "apb_pclk";
-			status="disabled";
+			status = "disabled";
 		};
 		spi0: spi@fe800000 {
 			compatible = "arm,pl022", "arm,primecell";
@@ -182,12 +182,13 @@
 			clocks = <&clk_bus>;
 			clock-names = "apb_pclk";
 		};
-		dmac0: dma@c1128000 {
+		dmac0: dma-controller@c1128000 {
 			compatible = "arm,pl330", "arm,primecell";
 			reg = <0x0 0xc1128000 0x1000>;
 			interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&clk_bus>;
 			clock-names = "apb_pclk";
+			#dma-cells = <1>;
 		};
 		gpio0: gpio@fd400000 {
 			#gpio-cells = <2>;
@@ -196,7 +197,7 @@
 			reg = <0x0 0xfd400000 0x1000>;
 			clocks = <&clk_bus>;
 			clock-names = "apb_pclk";
-			status="disabled";
+			status = "disabled";
 		};
 		gpio1: gpio@fd410000 {
 			#gpio-cells = <2>;
@@ -205,7 +206,7 @@
 			reg = <0x0 0xfd410000 0x1000>;
 			clocks = <&clk_bus>;
 			clock-names = "apb_pclk";
-			status="disabled";
+			status = "disabled";
 		};
 		gpio2: gpio@fd420000 {
 			#gpio-cells = <2>;
@@ -214,7 +215,7 @@
 			reg = <0x0 0xfd420000 0x1000>;
 			clocks = <&clk_bus>;
 			clock-names = "apb_pclk";
-			status="disabled";
+			status = "disabled";
 		};
 		gpio3: gpio@fd430000 {
 			#gpio-cells = <2>;
@@ -231,7 +232,7 @@
 			reg = <0x0 0xfd440000 0x1000>;
 			clocks = <&clk_bus>;
 			clock-names = "apb_pclk";
-			status="disabled";
+			status = "disabled";
 		};
 		gpio5: gpio@fd450000 {
 			#gpio-cells = <2>;
@@ -240,7 +241,7 @@
 			reg = <0x0 0xfd450000 0x1000>;
 			clocks = <&clk_bus>;
 			clock-names = "apb_pclk";
-			status="disabled";
+			status = "disabled";
 		};
 		gpio6: gpio@fd460000 {
 			#gpio-cells = <2>;
@@ -249,7 +250,7 @@
 			reg = <0x0 0xfd460000 0x1000>;
 			clocks = <&clk_bus>;
 			clock-names = "apb_pclk";
-			status="disabled";
+			status = "disabled";
 		};
 		gpio7: gpio@fd470000 {
 			#gpio-cells = <2>;
@@ -258,7 +259,7 @@
 			reg = <0x0 0xfd470000 0x1000>;
 			clocks = <&clk_bus>;
 			clock-names = "apb_pclk";
-			status="disabled";
+			status = "disabled";
 		};
 		gpio8: gpio@fd480000 {
 			#gpio-cells = <2>;
@@ -267,7 +268,7 @@
 			reg = <0x0 0xfd480000 0x1000>;
 			clocks = <&clk_bus>;
 			clock-names = "apb_pclk";
-			status="disabled";
+			status = "disabled";
 		};
 		gpio9: gpio@fd490000 {
 			#gpio-cells = <2>;
@@ -276,7 +277,7 @@
 			reg = <0x0 0xfd490000 0x1000>;
 			clocks = <&clk_bus>;
 			clock-names = "apb_pclk";
-			status="disabled";
+			status = "disabled";
 		};
 		gpio10: gpio@fd4a0000 {
 			#gpio-cells = <2>;
@@ -285,7 +286,7 @@
 			reg = <0x0 0xfd4a0000 0x1000>;
 			clocks = <&clk_bus>;
 			clock-names = "apb_pclk";
-			status="disabled";
+			status = "disabled";
 		};
 		gpio11: gpio@fd4b0000 {
 			#gpio-cells = <2>;
@@ -302,7 +303,7 @@
 			reg = <0x0 0xfd4c0000 0x1000>;
 			clocks = <&clk_bus>;
 			clock-names = "apb_pclk";
-			status="disabled";
+			status = "disabled";
 		};
 		gpio13: gpio@fd4d0000 {
 			#gpio-cells = <2>;
@@ -311,7 +312,7 @@
 			reg = <0x0 0xfd4d0000 0x1000>;
 			clocks = <&clk_bus>;
 			clock-names = "apb_pclk";
-			status="disabled";
+			status = "disabled";
 		};
 		gpio14: gpio@fd4e0000 {
 			#gpio-cells = <2>;
@@ -320,7 +321,7 @@
 			reg = <0x0 0xfd4e0000 0x1000>;
 			clocks = <&clk_bus>;
 			clock-names = "apb_pclk";
-			status="disabled";
+			status = "disabled";
 		};
 		gpio15: gpio@fd4f0000 {
 			#gpio-cells = <2>;
@@ -329,7 +330,7 @@
 			reg = <0x0 0xfd4f0000 0x1000>;
 			clocks = <&clk_bus>;
 			clock-names = "apb_pclk";
-			status="disabled";
+			status = "disabled";
 		};
 		gpio16: gpio@fd500000 {
 			#gpio-cells = <2>;
@@ -338,7 +339,7 @@
 			reg = <0x0 0xfd500000 0x1000>;
 			clocks = <&clk_bus>;
 			clock-names = "apb_pclk";
-			status="disabled";
+			status = "disabled";
 		};
 		gpio17: gpio@fd510000 {
 			#gpio-cells = <2>;
diff --git a/arch/arm64/boot/dts/marvell/Makefile b/arch/arm64/boot/dts/marvell/Makefile
index 1c794cdcb8e6..058237681fe5 100644
--- a/arch/arm64/boot/dts/marvell/Makefile
+++ b/arch/arm64/boot/dts/marvell/Makefile
@@ -1,6 +1,7 @@
 # SPDX-License-Identifier: GPL-2.0
 # Mvebu SoC Family
 dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-db.dtb
+dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-eDPU.dtb
 dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-espressobin.dtb
 dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-espressobin-emmc.dtb
 dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-espressobin-ultra.dtb
@@ -24,3 +25,4 @@ dtb-$(CONFIG_ARCH_MVEBU) += cn9132-db.dtb
 dtb-$(CONFIG_ARCH_MVEBU) += cn9132-db-B.dtb
 dtb-$(CONFIG_ARCH_MVEBU) += cn9130-crb-A.dtb
 dtb-$(CONFIG_ARCH_MVEBU) += cn9130-crb-B.dtb
+dtb-$(CONFIG_ARCH_MVEBU) += ac5-98dx35xx-rd.dtb
diff --git a/arch/arm64/boot/dts/marvell/ac5-98dx25xx.dtsi b/arch/arm64/boot/dts/marvell/ac5-98dx25xx.dtsi
new file mode 100644
index 000000000000..44ed6f963b75
--- /dev/null
+++ b/arch/arm64/boot/dts/marvell/ac5-98dx25xx.dtsi
@@ -0,0 +1,321 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device Tree For AC5.
+ *
+ * Copyright (C) 2021 Marvell
+ * Copyright (C) 2022 Allied Telesis Labs
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+	model = "Marvell AC5 SoC";
+	compatible = "marvell,ac5";
+	interrupt-parent = <&gic>;
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	cpus {
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cpu-map {
+			cluster0 {
+				core0 {
+					cpu = <&cpu0>;
+				};
+				core1 {
+					cpu = <&cpu1>;
+				};
+			};
+		};
+
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a55";
+			reg = <0x0 0x0>;
+			enable-method = "psci";
+			next-level-cache = <&l2>;
+		};
+
+		cpu1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a55";
+			reg = <0x0 0x100>;
+			enable-method = "psci";
+			next-level-cache = <&l2>;
+		};
+
+		l2: l2-cache {
+			compatible = "cache";
+		};
+	};
+
+	psci {
+		compatible = "arm,psci-0.2";
+		method = "smc";
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_PPI 8 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_PPI 10 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
+	pmu {
+		compatible = "arm,armv8-pmuv3";
+		interrupts = <GIC_PPI 12 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
+	soc {
+		compatible = "simple-bus";
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+		dma-ranges;
+
+		internal-regs@7f000000 {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "simple-bus";
+			/* 16M internal register @ 0x7f00_0000 */
+			ranges = <0x0 0x0 0x7f000000 0x1000000>;
+			dma-coherent;
+
+			uart0: serial@12000 {
+				compatible = "snps,dw-apb-uart";
+				reg = <0x12000 0x100>;
+				reg-shift = <2>;
+				interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
+				reg-io-width = <1>;
+				clocks = <&cnm_clock>;
+				status = "okay";
+			};
+
+			uart1: serial@12100 {
+				compatible = "snps,dw-apb-uart";
+				reg = <0x11000 0x100>;
+				reg-shift = <2>;
+				interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
+				reg-io-width = <1>;
+				clocks = <&cnm_clock>;
+				status = "disabled";
+			};
+
+			uart2: serial@12200 {
+				compatible = "snps,dw-apb-uart";
+				reg = <0x12200 0x100>;
+				reg-shift = <2>;
+				interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
+				reg-io-width = <1>;
+				clocks = <&cnm_clock>;
+				status = "disabled";
+			};
+
+			uart3: serial@12300 {
+				compatible = "snps,dw-apb-uart";
+				reg = <0x12300 0x100>;
+				reg-shift = <2>;
+				interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
+				reg-io-width = <1>;
+				clocks = <&cnm_clock>;
+				status = "disabled";
+			};
+
+			mdio: mdio@22004 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "marvell,orion-mdio";
+				reg = <0x22004 0x4>;
+				clocks = <&cnm_clock>;
+			};
+
+			i2c0: i2c@11000{
+				compatible = "marvell,mv78230-i2c";
+				reg = <0x11000 0x20>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				clocks = <&cnm_clock>;
+				clock-names = "core";
+				interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
+				clock-frequency=<100000>;
+
+				pinctrl-names = "default", "gpio";
+				pinctrl-0 = <&i2c0_pins>;
+				pinctrl-1 = <&i2c0_gpio>;
+				scl-gpios = <&gpio0 26 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+				sda-gpios = <&gpio0 27 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+				status = "disabled";
+			};
+
+			i2c1: i2c@11100{
+				compatible = "marvell,mv78230-i2c";
+				reg = <0x11100 0x20>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				clocks = <&cnm_clock>;
+				clock-names = "core";
+				interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>;
+				clock-frequency=<100000>;
+
+				pinctrl-names = "default", "gpio";
+				pinctrl-0 = <&i2c1_pins>;
+				pinctrl-1 = <&i2c1_gpio>;
+				scl-gpios = <&gpio0 20 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+				sda-gpios = <&gpio0 21 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+				status = "disabled";
+			};
+
+			gpio0: gpio@18100 {
+				compatible = "marvell,orion-gpio";
+				reg = <0x18100 0x40>;
+				ngpios = <32>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				gpio-ranges = <&pinctrl0 0 0 32>;
+				marvell,pwm-offset = <0x1f0>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
+			};
+
+			gpio1: gpio@18140 {
+				reg = <0x18140 0x40>;
+				compatible = "marvell,orion-gpio";
+				ngpios = <14>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				gpio-ranges = <&pinctrl0 0 32 14>;
+				marvell,pwm-offset = <0x1f0>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
+			};
+		};
+
+		/*
+		 * Dedicated section for devices behind 32bit controllers so we
+		 * can configure specific DMA mapping for them
+		 */
+		behind-32bit-controller@7f000000 {
+			compatible = "simple-bus";
+			#address-cells = <0x2>;
+			#size-cells = <0x2>;
+			ranges = <0x0 0x0 0x0 0x7f000000 0x0 0x1000000>;
+			/* Host phy ram starts at 0x200M */
+			dma-ranges = <0x0 0x0 0x2 0x0 0x1 0x0>;
+			dma-coherent;
+
+			eth0: ethernet@20000 {
+				compatible = "marvell,armada-ac5-neta";
+				reg = <0x0 0x20000 0x0 0x4000>;
+				interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&cnm_clock>;
+				phy-mode = "sgmii";
+				status = "disabled";
+			};
+
+			eth1: ethernet@24000 {
+				compatible = "marvell,armada-ac5-neta";
+				reg = <0x0 0x24000 0x0 0x4000>;
+				interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&cnm_clock>;
+				phy-mode = "sgmii";
+				status = "disabled";
+			};
+
+			usb0: usb@80000 {
+				compatible = "marvell,orion-ehci";
+				reg = <0x0 0x80000 0x0 0x500>;
+				interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>;
+				status = "disabled";
+			};
+
+			usb1: usb@a0000 {
+				compatible = "marvell,orion-ehci";
+				reg = <0x0 0xa0000 0x0 0x500>;
+				interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>;
+				status = "disabled";
+			};
+		};
+
+		pinctrl0: pinctrl@80020100 {
+			compatible = "marvell,ac5-pinctrl";
+			reg = <0 0x80020100 0 0x20>;
+
+			i2c0_pins: i2c0-pins {
+				marvell,pins = "mpp26", "mpp27";
+				marvell,function = "i2c0";
+			};
+
+			i2c0_gpio: i2c0-gpio-pins {
+				marvell,pins = "mpp26", "mpp27";
+				marvell,function = "gpio";
+			};
+
+			i2c1_pins: i2c1-pins {
+				marvell,pins = "mpp20", "mpp21";
+				marvell,function = "i2c1";
+			};
+
+			i2c1_gpio: i2c1-gpio-pins {
+				marvell,pins = "mpp20", "mpp21";
+				marvell,function = "i2c1";
+			};
+		};
+
+		spi0: spi@805a0000 {
+			compatible = "marvell,armada-3700-spi";
+			reg = <0x0 0x805a0000 0x0 0x50>;
+			#address-cells = <0x1>;
+			#size-cells = <0x0>;
+			clocks = <&spi_clock>;
+			interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>;
+			num-cs = <1>;
+			status = "disabled";
+		};
+
+		spi1: spi@805a8000 {
+			compatible = "marvell,armada-3700-spi";
+			reg = <0x0 0x805a8000 0x0 0x50>;
+			#address-cells = <0x1>;
+			#size-cells = <0x0>;
+			clocks = <&spi_clock>;
+			interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
+			num-cs = <1>;
+			status = "disabled";
+		};
+
+		gic: interrupt-controller@80600000 {
+			compatible = "arm,gic-v3";
+			#interrupt-cells = <3>;
+			interrupt-controller;
+			reg = <0x0 0x80600000 0x0 0x10000>, /* GICD */
+			      <0x0 0x80660000 0x0 0x40000>; /* GICR */
+			interrupts = <GIC_PPI 6 IRQ_TYPE_LEVEL_HIGH>;
+		};
+	};
+
+	clocks {
+		cnm_clock: cnm-clock {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <328000000>;
+		};
+
+		spi_clock: spi-clock {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <200000000>;
+		};
+	};
+};
diff --git a/arch/arm64/boot/dts/marvell/ac5-98dx35xx-rd.dts b/arch/arm64/boot/dts/marvell/ac5-98dx35xx-rd.dts
new file mode 100644
index 000000000000..f0ebdb84eec9
--- /dev/null
+++ b/arch/arm64/boot/dts/marvell/ac5-98dx35xx-rd.dts
@@ -0,0 +1,101 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device Tree For RD-AC5X.
+ *
+ * Copyright (C) 2021 Marvell
+ * Copyright (C) 2022 Allied Telesis Labs
+ */
+/*
+ * Device Tree file for Marvell Alleycat 5X development board
+ * This board file supports the B configuration of the board
+ */
+
+/dts-v1/;
+
+#include "ac5-98dx35xx.dtsi"
+
+/ {
+	model = "Marvell RD-AC5X Board";
+	compatible = "marvell,rd-ac5x", "marvell,ac5x", "marvell,ac5";
+
+	aliases {
+		serial0 = &uart0;
+		spiflash0 = &spiflash0;
+		gpio0 = &gpio0;
+		gpio1 = &gpio1;
+		ethernet0 = &eth0;
+		ethernet1 = &eth1;
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x2 0x00000000 0x0 0x40000000>;
+	};
+
+	usb1phy: usb-phy {
+		compatible = "usb-nop-xceiv";
+		#phy-cells = <0>;
+	};
+};
+
+&mdio {
+	phy0: ethernet-phy@0 {
+		reg = <0>;
+	};
+};
+
+&i2c0 {
+	status = "okay";
+};
+
+&i2c1 {
+	status = "okay";
+};
+
+&eth0 {
+	status = "okay";
+	phy-handle = <&phy0>;
+};
+
+/* USB0 is a host USB */
+&usb0 {
+	status = "okay";
+};
+
+/* USB1 is a peripheral USB */
+&usb1 {
+	status = "okay";
+	phys = <&usb1phy>;
+	phy-names = "usb-phy";
+	dr_mode = "peripheral";
+};
+
+&spi0 {
+	status = "okay";
+
+	spiflash0: flash@0 {
+		compatible = "jedec,spi-nor";
+		spi-max-frequency = <50000000>;
+		spi-tx-bus-width = <1>; /* 1-single, 2-dual, 4-quad */
+		spi-rx-bus-width = <1>; /* 1-single, 2-dual, 4-quad */
+		reg = <0>;
+
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		partition@0 {
+			label = "spi_flash_part0";
+			reg = <0x0 0x800000>;
+		};
+
+		parition@1 {
+			label = "spi_flash_part1";
+			reg = <0x800000 0x700000>;
+		};
+
+		parition@2 {
+			label = "spi_flash_part2";
+			reg = <0xF00000 0x100000>;
+		};
+	};
+};
diff --git a/arch/arm64/boot/dts/marvell/ac5-98dx35xx.dtsi b/arch/arm64/boot/dts/marvell/ac5-98dx35xx.dtsi
new file mode 100644
index 000000000000..2ab72f854bea
--- /dev/null
+++ b/arch/arm64/boot/dts/marvell/ac5-98dx35xx.dtsi
@@ -0,0 +1,17 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device Tree For AC5X.
+ *
+ * Copyright (C) 2022 Allied Telesis Labs
+ */
+
+#include "ac5-98dx25xx.dtsi"
+
+/ {
+	model = "Marvell AC5X SoC";
+	compatible = "marvell,ac5x", "marvell,ac5";
+};
+
+&cnm_clock {
+	clock-frequency = <325000000>;
+};
diff --git a/arch/arm64/boot/dts/marvell/armada-3720-db.dts b/arch/arm64/boot/dts/marvell/armada-3720-db.dts
index 3e5789f37206..bd4e61d5448e 100644
--- a/arch/arm64/boot/dts/marvell/armada-3720-db.dts
+++ b/arch/arm64/boot/dts/marvell/armada-3720-db.dts
@@ -164,7 +164,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&spi_quad_pins>;
 
-	m25p80@0 {
+	flash@0 {
 		compatible = "jedec,spi-nor";
 		reg = <0>;
 		spi-max-frequency = <108000000>;
diff --git a/arch/arm64/boot/dts/marvell/armada-3720-eDPU.dts b/arch/arm64/boot/dts/marvell/armada-3720-eDPU.dts
new file mode 100644
index 000000000000..57fc698e55d0
--- /dev/null
+++ b/arch/arm64/boot/dts/marvell/armada-3720-eDPU.dts
@@ -0,0 +1,14 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+/dts-v1/;
+
+#include "armada-3720-uDPU.dtsi"
+
+/ {
+	model = "Methode eDPU Board";
+	compatible = "methode,edpu", "marvell,armada3720", "marvell,armada3710";
+};
+
+&eth0 {
+	phy-mode = "2500base-x";
+};
diff --git a/arch/arm64/boot/dts/marvell/armada-3720-espressobin-ultra.dts b/arch/arm64/boot/dts/marvell/armada-3720-espressobin-ultra.dts
index c5eb3604dd5b..1b2ed63ae6a2 100644
--- a/arch/arm64/boot/dts/marvell/armada-3720-espressobin-ultra.dts
+++ b/arch/arm64/boot/dts/marvell/armada-3720-espressobin-ultra.dts
@@ -12,8 +12,8 @@
 
 / {
 	model = "Globalscale Marvell ESPRESSOBin Ultra Board";
-	compatible = "globalscale,espressobin-ultra", "marvell,armada3720",
-		     "marvell,armada3710";
+	compatible = "globalscale,espressobin-ultra", "globalscale,espressobin",
+		     "marvell,armada3720", "marvell,armada3710";
 
 	aliases {
 		/* ethernet1 is WAN port */
@@ -71,10 +71,6 @@
 
 &spi0 {
 	flash@0 {
-		spi-max-frequency = <108000000>;
-		spi-rx-bus-width = <4>;
-		spi-tx-bus-width = <4>;
-
 		partitions {
 			compatible = "fixed-partitions";
 			#address-cells = <1>;
@@ -112,18 +108,21 @@
 
 &usb3 {
 	usb-phy = <&usb3_phy>;
-	status = "disabled";
 };
 
 &mdio {
 	extphy: ethernet-phy@1 {
 		reg = <1>;
+
+		reset-gpios = <&gpionb 2 GPIO_ACTIVE_LOW>;
 	};
 };
 
 &switch0 {
 	reg = <3>;
 
+	reset-gpios = <&gpiosb 23 GPIO_ACTIVE_LOW>;
+
 	ports {
 		switch0port1: port@1 {
 			reg = <1>;
diff --git a/arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts b/arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts
index 04da07ae4420..ada164d423f3 100644
--- a/arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts
+++ b/arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts
@@ -18,6 +18,7 @@
 
 	aliases {
 		spi0 = &spi0;
+		ethernet0 = &eth0;
 		ethernet1 = &eth1;
 		mmc0 = &sdhci0;
 		mmc1 = &sdhci1;
@@ -34,7 +35,7 @@
 
 	leds {
 		compatible = "gpio-leds";
-		red {
+		led {
 			label = "mox:red:activity";
 			gpios = <&gpiosb 21 GPIO_ACTIVE_LOW>;
 			linux,default-trigger = "default-on";
@@ -44,7 +45,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		reset {
+		key-reset {
 			label = "reset";
 			linux,code = <KEY_RESTART>;
 			gpios = <&gpiosb 20 GPIO_ACTIVE_LOW>;
@@ -99,11 +100,11 @@
 	sfp: sfp {
 		compatible = "sff,sfp";
 		i2c-bus = <&i2c0>;
-		los-gpio = <&moxtet_sfp 0 GPIO_ACTIVE_HIGH>;
-		tx-fault-gpio = <&moxtet_sfp 1 GPIO_ACTIVE_HIGH>;
-		mod-def0-gpio = <&moxtet_sfp 2 GPIO_ACTIVE_LOW>;
-		tx-disable-gpio = <&moxtet_sfp 4 GPIO_ACTIVE_HIGH>;
-		rate-select0-gpio = <&moxtet_sfp 5 GPIO_ACTIVE_HIGH>;
+		los-gpios = <&moxtet_sfp 0 GPIO_ACTIVE_HIGH>;
+		tx-fault-gpios = <&moxtet_sfp 1 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&moxtet_sfp 2 GPIO_ACTIVE_LOW>;
+		tx-disable-gpios = <&moxtet_sfp 4 GPIO_ACTIVE_HIGH>;
+		rate-select0-gpios = <&moxtet_sfp 5 GPIO_ACTIVE_HIGH>;
 		maximum-power-milliwatt = <3000>;
 
 		/* enabled by U-Boot if SFP module is present */
@@ -138,7 +139,9 @@
 	/*
 	 * U-Boot port for Turris Mox has a bug which always expects that "ranges" DT property
 	 * contains exactly 2 ranges with 3 (child) address cells, 2 (parent) address cells and
-	 * 2 size cells and also expects that the second range starts at 16 MB offset. If these
+	 * 2 size cells and also expects that the second range starts at 16 MB offset. Also it
+	 * expects that first range uses same address for PCI (child) and CPU (parent) cells (so
+	 * no remapping) and that this address is the lowest from all specified ranges. If these
 	 * conditions are not met then U-Boot crashes during loading kernel DTB file. PCIe address
 	 * space is 128 MB long, so the best split between MEM and IO is to use fixed 16 MB window
 	 * for IO and the rest 112 MB (64+32+16) for MEM, despite that maximal IO size is just 64 kB.
@@ -147,6 +150,9 @@
 	 * https://source.denx.de/u-boot/u-boot/-/commit/cb2ddb291ee6fcbddd6d8f4ff49089dfe580f5d7
 	 * https://source.denx.de/u-boot/u-boot/-/commit/c64ac3b3185aeb3846297ad7391fc6df8ecd73bf
 	 * https://source.denx.de/u-boot/u-boot/-/commit/4a82fca8e330157081fc132a591ebd99ba02ee33
+	 * Bug related to requirement of same child and parent addresses for first range is fixed
+	 * in U-Boot version 2022.04 by following commit:
+	 * https://source.denx.de/u-boot/u-boot/-/commit/1fd54253bca7d43d046bba4853fe5fafd034bc17
 	 */
 	#address-cells = <3>;
 	#size-cells = <2>;
@@ -205,7 +211,7 @@
 	assigned-clock-parents = <&tbg 1>;
 	assigned-clock-rates = <20000000>;
 
-	spi-flash@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "jedec,spi-nor";
@@ -297,7 +303,7 @@
 	/* switch nodes are enabled by U-Boot if modules are present */
 	switch0@10 {
 		compatible = "marvell,mv88e6190";
-		reg = <0x10 0>;
+		reg = <0x10>;
 		dsa,member = <0 0>;
 		interrupt-parent = <&moxtet>;
 		interrupts = <MOXTET_IRQ_PERIDOT(0)>;
@@ -422,7 +428,7 @@
 
 	switch0@2 {
 		compatible = "marvell,mv88e6085";
-		reg = <0x2 0>;
+		reg = <0x2>;
 		dsa,member = <0 0>;
 		interrupt-parent = <&moxtet>;
 		interrupts = <MOXTET_IRQ_TOPAZ>;
@@ -489,7 +495,7 @@
 
 	switch1@11 {
 		compatible = "marvell,mv88e6190";
-		reg = <0x11 0>;
+		reg = <0x11>;
 		dsa,member = <0 1>;
 		interrupt-parent = <&moxtet>;
 		interrupts = <MOXTET_IRQ_PERIDOT(1)>;
@@ -614,7 +620,7 @@
 
 	switch1@2 {
 		compatible = "marvell,mv88e6085";
-		reg = <0x2 0>;
+		reg = <0x2>;
 		dsa,member = <0 1>;
 		interrupt-parent = <&moxtet>;
 		interrupts = <MOXTET_IRQ_TOPAZ>;
@@ -681,7 +687,7 @@
 
 	switch2@12 {
 		compatible = "marvell,mv88e6190";
-		reg = <0x12 0>;
+		reg = <0x12>;
 		dsa,member = <0 2>;
 		interrupt-parent = <&moxtet>;
 		interrupts = <MOXTET_IRQ_PERIDOT(2)>;
@@ -797,7 +803,7 @@
 
 	switch2@2 {
 		compatible = "marvell,mv88e6085";
-		reg = <0x2 0>;
+		reg = <0x2>;
 		dsa,member = <0 2>;
 		interrupt-parent = <&moxtet>;
 		interrupts = <MOXTET_IRQ_TOPAZ>;
diff --git a/arch/arm64/boot/dts/marvell/armada-3720-uDPU.dts b/arch/arm64/boot/dts/marvell/armada-3720-uDPU.dts
index 95d46e8d081c..c76eceabd33e 100644
--- a/arch/arm64/boot/dts/marvell/armada-3720-uDPU.dts
+++ b/arch/arm64/boot/dts/marvell/armada-3720-uDPU.dts
@@ -1,120 +1,22 @@
 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
-/*
- * Device tree for the uDPU board.
- * Based on Marvell Armada 3720 development board (DB-88F3720-DDR3)
- * Copyright (C) 2016 Marvell
- * Copyright (C) 2019 Methode Electronics
- * Copyright (C) 2019 Telus
- *
- * Vladimir Vid <vladimir.vid@sartura.hr>
- */
 
 /dts-v1/;
 
-#include <dt-bindings/gpio/gpio.h>
-#include "armada-372x.dtsi"
+#include "armada-3720-uDPU.dtsi"
 
 / {
 	model = "Methode uDPU Board";
-	compatible = "methode,udpu", "marvell,armada3720";
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	memory@0 {
-		device_type = "memory";
-		reg = <0x00000000 0x00000000 0x00000000 0x20000000>;
-	};
-
-	leds {
-		pinctrl-names = "default";
-		compatible = "gpio-leds";
-
-		power1 {
-			label = "udpu:green:power";
-			gpios = <&gpionb 11 GPIO_ACTIVE_LOW>;
-		};
-
-		power2 {
-			label = "udpu:red:power";
-			gpios = <&gpionb 12 GPIO_ACTIVE_LOW>;
-		};
-
-		network1 {
-			label = "udpu:green:network";
-			gpios = <&gpionb 13 GPIO_ACTIVE_LOW>;
-		};
-
-		network2 {
-			label = "udpu:red:network";
-			gpios = <&gpionb 14 GPIO_ACTIVE_LOW>;
-		};
-
-		alarm1 {
-			label = "udpu:green:alarm";
-			gpios = <&gpionb 15 GPIO_ACTIVE_LOW>;
-		};
-
-		alarm2 {
-			label = "udpu:red:alarm";
-			gpios = <&gpionb 16 GPIO_ACTIVE_LOW>;
-		};
-	};
+	compatible = "methode,udpu", "marvell,armada3720", "marvell,armada3710";
 
 	sfp_eth0: sfp-eth0 {
 		compatible = "sff,sfp";
 		i2c-bus = <&i2c0>;
-		los-gpio = <&gpiosb 2 GPIO_ACTIVE_HIGH>;
-		mod-def0-gpio = <&gpiosb 3 GPIO_ACTIVE_LOW>;
-		tx-disable-gpio = <&gpiosb 4 GPIO_ACTIVE_HIGH>;
-		tx-fault-gpio = <&gpiosb 5 GPIO_ACTIVE_HIGH>;
+		los-gpios = <&gpiosb 2 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&gpiosb 3 GPIO_ACTIVE_LOW>;
+		tx-disable-gpios = <&gpiosb 4 GPIO_ACTIVE_HIGH>;
+		tx-fault-gpios = <&gpiosb 5 GPIO_ACTIVE_HIGH>;
 		maximum-power-milliwatt = <3000>;
 	};
-
-	sfp_eth1: sfp-eth1 {
-		compatible = "sff,sfp";
-		i2c-bus = <&i2c1>;
-		los-gpio = <&gpiosb 7 GPIO_ACTIVE_HIGH>;
-		mod-def0-gpio = <&gpiosb 8 GPIO_ACTIVE_LOW>;
-		tx-disable-gpio = <&gpiosb 9 GPIO_ACTIVE_HIGH>;
-		tx-fault-gpio = <&gpiosb 10 GPIO_ACTIVE_HIGH>;
-		maximum-power-milliwatt = <3000>;
-	};
-};
-
-&sdhci0 {
-	status = "okay";
-	bus-width = <8>;
-	mmc-ddr-1_8v;
-	mmc-hs400-1_8v;
-	marvell,pad-type = "fixed-1-8v";
-	non-removable;
-	no-sd;
-	no-sdio;
-};
-
-&spi0 {
-	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&spi_quad_pins>;
-
-	m25p80@0 {
-		compatible = "jedec,spi-nor";
-		reg = <0>;
-		spi-max-frequency = <54000000>;
-
-		partitions {
-			compatible = "fixed-partitions";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			/* only bootloader is located on the SPI */
-			partition@0 {
-				label = "uboot";
-				reg = <0 0x400000>;
-			};
-		};
-	};
 };
 
 &pinctrl_nb {
@@ -122,11 +24,6 @@
 		groups = "i2c1";
 		function = "gpio";
 	};
-
-	i2c2_recovery_pins: i2c2-recovery-pins {
-		groups = "i2c2";
-		function = "gpio";
-	};
 };
 
 &i2c0 {
@@ -139,50 +36,7 @@
 	sda-gpios = <&gpionb 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 };
 
-&i2c1 {
-	status = "okay";
-	pinctrl-names = "default", "recovery";
-	pinctrl-0 = <&i2c2_pins>;
-	pinctrl-1 = <&i2c2_recovery_pins>;
-	/delete-property/mrvl,i2c-fast-mode;
-	scl-gpios = <&gpionb 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
-	sda-gpios = <&gpionb 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
-
-	lm75@48 {
-		status = "okay";
-		compatible = "lm75";
-		reg = <0x48>;
-	};
-
-	lm75@49 {
-		status = "okay";
-		compatible = "lm75";
-		reg = <0x49>;
-	};
-};
-
 &eth0 {
 	phy-mode = "sgmii";
-	status = "okay";
-	managed = "in-band-status";
-	phys = <&comphy1 0>;
 	sfp = <&sfp_eth0>;
 };
-
-&eth1 {
-	phy-mode = "sgmii";
-	status = "okay";
-	managed = "in-band-status";
-	phys = <&comphy0 1>;
-	sfp = <&sfp_eth1>;
-};
-
-&usb3 {
-	status = "okay";
-	phys = <&usb2_utmi_otg_phy>;
-	phy-names = "usb2-utmi-otg-phy";
-};
-
-&uart0 {
-	status = "okay";
-};
diff --git a/arch/arm64/boot/dts/marvell/armada-3720-uDPU.dtsi b/arch/arm64/boot/dts/marvell/armada-3720-uDPU.dtsi
new file mode 100644
index 000000000000..3f79923376fb
--- /dev/null
+++ b/arch/arm64/boot/dts/marvell/armada-3720-uDPU.dtsi
@@ -0,0 +1,160 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device tree for the uDPU board.
+ * Based on Marvell Armada 3720 development board (DB-88F3720-DDR3)
+ * Copyright (C) 2016 Marvell
+ * Copyright (C) 2019 Methode Electronics
+ * Copyright (C) 2019 Telus
+ *
+ * Vladimir Vid <vladimir.vid@sartura.hr>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include "armada-372x.dtsi"
+
+/ {
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x00000000 0x00000000 0x20000000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-power1 {
+			label = "udpu:green:power";
+			gpios = <&gpionb 11 GPIO_ACTIVE_LOW>;
+		};
+
+		led-power2 {
+			label = "udpu:red:power";
+			gpios = <&gpionb 12 GPIO_ACTIVE_LOW>;
+		};
+
+		led-network1 {
+			label = "udpu:green:network";
+			gpios = <&gpionb 13 GPIO_ACTIVE_LOW>;
+		};
+
+		led-network2 {
+			label = "udpu:red:network";
+			gpios = <&gpionb 14 GPIO_ACTIVE_LOW>;
+		};
+
+		led-alarm1 {
+			label = "udpu:green:alarm";
+			gpios = <&gpionb 15 GPIO_ACTIVE_LOW>;
+		};
+
+		led-alarm2 {
+			label = "udpu:red:alarm";
+			gpios = <&gpionb 16 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	sfp_eth1: sfp-eth1 {
+		compatible = "sff,sfp";
+		i2c-bus = <&i2c1>;
+		los-gpio = <&gpiosb 7 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpio = <&gpiosb 8 GPIO_ACTIVE_LOW>;
+		tx-disable-gpio = <&gpiosb 9 GPIO_ACTIVE_HIGH>;
+		tx-fault-gpio = <&gpiosb 10 GPIO_ACTIVE_HIGH>;
+		maximum-power-milliwatt = <3000>;
+	};
+};
+
+&sdhci0 {
+	status = "okay";
+	bus-width = <8>;
+	mmc-ddr-1_8v;
+	mmc-hs400-1_8v;
+	marvell,pad-type = "fixed-1-8v";
+	non-removable;
+	no-sd;
+	no-sdio;
+};
+
+&spi0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi_quad_pins>;
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <54000000>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "firmware";
+				reg = <0x0 0x180000>;
+			};
+
+			partition@180000 {
+				label = "u-boot-env";
+				reg = <0x180000 0x10000>;
+			};
+		};
+	};
+};
+
+&pinctrl_nb {
+	i2c2_recovery_pins: i2c2-recovery-pins {
+		groups = "i2c2";
+		function = "gpio";
+	};
+};
+
+&i2c1 {
+	status = "okay";
+	pinctrl-names = "default", "recovery";
+	pinctrl-0 = <&i2c2_pins>;
+	pinctrl-1 = <&i2c2_recovery_pins>;
+	/delete-property/mrvl,i2c-fast-mode;
+	scl-gpios = <&gpionb 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpionb 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+
+	temp-sensor@48 {
+		compatible = "ti,tmp75c";
+		reg = <0x48>;
+	};
+
+	temp-sensor@49 {
+		compatible = "ti,tmp75c";
+		reg = <0x49>;
+	};
+};
+
+&eth0 {
+	status = "okay";
+	managed = "in-band-status";
+	phys = <&comphy1 0>;
+};
+
+&eth1 {
+	phy-mode = "sgmii";
+	status = "okay";
+	managed = "in-band-status";
+	phys = <&comphy0 1>;
+	sfp = <&sfp_eth1>;
+};
+
+&usb3 {
+	status = "okay";
+	phys = <&usb2_utmi_otg_phy>;
+	phy-names = "usb2-utmi-otg-phy";
+};
+
+&uart0 {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/marvell/armada-37xx.dtsi b/arch/arm64/boot/dts/marvell/armada-37xx.dtsi
index 9acc5d2b5a00..df152c72276b 100644
--- a/arch/arm64/boot/dts/marvell/armada-37xx.dtsi
+++ b/arch/arm64/boot/dts/marvell/armada-37xx.dtsi
@@ -132,10 +132,20 @@
 				reg = <0x11500 0x40>;
 			};
 
+			uartclk: clock-controller@12010 {
+				compatible = "marvell,armada-3700-uart-clock";
+				reg = <0x12010 0x4>, <0x12210 0x4>;
+				clocks = <&tbg 0>, <&tbg 1>, <&tbg 2>,
+					 <&tbg 3>, <&xtalclk>;
+				clock-names = "TBG-A-P", "TBG-B-P", "TBG-A-S",
+					      "TBG-B-S", "xtal";
+				#clock-cells = <1>;
+			};
+
 			uart0: serial@12000 {
 				compatible = "marvell,armada-3700-uart";
 				reg = <0x12000 0x18>;
-				clocks = <&xtalclk>;
+				clocks = <&uartclk 0>;
 				interrupts =
 				<GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
 				<GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
@@ -147,7 +157,7 @@
 			uart1: serial@12200 {
 				compatible = "marvell,armada-3700-uart-ext";
 				reg = <0x12200 0x30>;
-				clocks = <&xtalclk>;
+				clocks = <&uartclk 1>;
 				interrupts =
 				<GIC_SPI 30 IRQ_TYPE_EDGE_RISING>,
 				<GIC_SPI 31 IRQ_TYPE_EDGE_RISING>;
@@ -265,6 +275,8 @@
 					    "lane2_sata_usb3";
 				#address-cells = <1>;
 				#size-cells = <0>;
+				clocks = <&xtalclk>;
+				clock-names = "xtal";
 
 				comphy0: phy@0 {
 					reg = <0>;
@@ -432,7 +444,7 @@
 				#mbox-cells = <1>;
 			};
 
-			sdhci1: sdhci@d0000 {
+			sdhci1: mmc@d0000 {
 				compatible = "marvell,armada-3700-sdhci",
 					     "marvell,sdhci-xenon";
 				reg = <0xd0000 0x300>,
@@ -443,7 +455,7 @@
 				status = "disabled";
 			};
 
-			sdhci0: sdhci@d8000 {
+			sdhci0: mmc@d8000 {
 				compatible = "marvell,armada-3700-sdhci",
 					     "marvell,sdhci-xenon";
 				reg = <0xd8000 0x300>,
@@ -487,6 +499,7 @@
 			bus-range = <0x00 0xff>;
 			interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
 			#interrupt-cells = <1>;
+			clocks = <&sb_periph_clk 13>;
 			msi-parent = <&pcie0>;
 			msi-controller;
 			/*
@@ -497,7 +510,7 @@
 			 * (totaling 127 MiB) for MEM.
 			 */
 			ranges = <0x82000000 0 0xe8000000   0 0xe8000000   0 0x07f00000   /* Port 0 MEM */
-				  0x81000000 0 0xefff0000   0 0xefff0000   0 0x00010000>; /* Port 0 IO */
+				  0x81000000 0 0x00000000   0 0xefff0000   0 0x00010000>; /* Port 0 IO */
 			interrupt-map-mask = <0 0 0 7>;
 			interrupt-map = <0 0 0 1 &pcie_intc 0>,
 					<0 0 0 2 &pcie_intc 1>,
diff --git a/arch/arm64/boot/dts/marvell/armada-7040-db.dts b/arch/arm64/boot/dts/marvell/armada-7040-db.dts
index cd326fe224ce..5e5baf6beea4 100644
--- a/arch/arm64/boot/dts/marvell/armada-7040-db.dts
+++ b/arch/arm64/boot/dts/marvell/armada-7040-db.dts
@@ -83,7 +83,7 @@
 &spi0 {
 	status = "okay";
 
-	spi-flash@0 {
+	flash@0 {
 		compatible = "jedec,spi-nor";
 		reg = <0>;
 		spi-max-frequency = <10000000>;
@@ -186,7 +186,7 @@
 &cp0_spi1 {
 	status = "okay";
 
-	spi-flash@0 {
+	flash@0 {
 		compatible = "jedec,spi-nor";
 		reg = <0x0>;
 		spi-max-frequency = <20000000>;
diff --git a/arch/arm64/boot/dts/marvell/armada-7040-mochabin.dts b/arch/arm64/boot/dts/marvell/armada-7040-mochabin.dts
index f3b0d57a24a3..7ca71f2d7afb 100644
--- a/arch/arm64/boot/dts/marvell/armada-7040-mochabin.dts
+++ b/arch/arm64/boot/dts/marvell/armada-7040-mochabin.dts
@@ -34,20 +34,20 @@
 	sfp_eth0: sfp-eth0 {
 		compatible = "sff,sfp";
 		i2c-bus = <&cp0_i2c1>;
-		los-gpio = <&sfp_gpio 3 GPIO_ACTIVE_HIGH>;
-		mod-def0-gpio = <&sfp_gpio 2 GPIO_ACTIVE_LOW>;
-		tx-disable-gpio = <&sfp_gpio 1 GPIO_ACTIVE_HIGH>;
-		tx-fault-gpio  = <&sfp_gpio 0 GPIO_ACTIVE_HIGH>;
+		los-gpios = <&sfp_gpio 3 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&sfp_gpio 2 GPIO_ACTIVE_LOW>;
+		tx-disable-gpios = <&sfp_gpio 1 GPIO_ACTIVE_HIGH>;
+		tx-fault-gpios = <&sfp_gpio 0 GPIO_ACTIVE_HIGH>;
 	};
 
 	/* SFP 1G */
 	sfp_eth2: sfp-eth2 {
 		compatible = "sff,sfp";
 		i2c-bus = <&cp0_i2c0>;
-		los-gpio = <&sfp_gpio 7 GPIO_ACTIVE_HIGH>;
-		mod-def0-gpio = <&sfp_gpio 6 GPIO_ACTIVE_LOW>;
-		tx-disable-gpio = <&sfp_gpio 5 GPIO_ACTIVE_HIGH>;
-		tx-fault-gpio  = <&sfp_gpio 4 GPIO_ACTIVE_HIGH>;
+		los-gpios = <&sfp_gpio 7 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&sfp_gpio 6 GPIO_ACTIVE_LOW>;
+		tx-disable-gpios = <&sfp_gpio 5 GPIO_ACTIVE_HIGH>;
+		tx-fault-gpios = <&sfp_gpio 4 GPIO_ACTIVE_HIGH>;
 	};
 };
 
@@ -155,7 +155,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&cp0_spi1_pins>;
 
-	spi-flash@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "jedec,spi-nor";
diff --git a/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts b/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts
index 8729c6467303..4125202028c8 100644
--- a/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts
+++ b/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts
@@ -64,8 +64,8 @@
 	sfp_cp0_eth0: sfp-cp0-eth0 {
 		compatible = "sff,sfp";
 		i2c-bus = <&cp0_i2c1>;
-		mod-def0-gpio = <&cp0_gpio2 17 GPIO_ACTIVE_LOW>;
-		tx-disable-gpio = <&cp1_gpio1 29 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&cp0_gpio2 17 GPIO_ACTIVE_LOW>;
+		tx-disable-gpios = <&cp1_gpio1 29 GPIO_ACTIVE_HIGH>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&cp0_sfp_present_pins &cp1_sfp_tx_disable_pins>;
 		maximum-power-milliwatt = <2000>;
@@ -94,7 +94,7 @@
 		pinctrl-0 = <&cp0_gpio_reset_pins &cp1_wps_button_pins>;
 		pinctrl-names = "default";
 
-		button_0 {
+		button-0 {
 			/* The rear button */
 			label = "Rear Button";
 			gpios = <&cp0_gpio2 7 GPIO_ACTIVE_LOW>;
@@ -102,7 +102,7 @@
 			linux,code = <BTN_0>;
 		};
 
-		button_1 {
+		button-1 {
 			/* The wps button */
 			label = "WPS Button";
 			gpios = <&cp1_gpio1 30 GPIO_ACTIVE_LOW>;
@@ -589,7 +589,7 @@
 	pinctrl-0 = <&cp1_spi1_pins>;
 	status = "okay";
 
-	spi-flash@0 {
+	flash@0 {
 		compatible = "st,w25q32";
 		spi-max-frequency = <50000000>;
 		reg = <0>;
diff --git a/arch/arm64/boot/dts/marvell/armada-8040-db.dts b/arch/arm64/boot/dts/marvell/armada-8040-db.dts
index f2e8e0df8865..92897bd7e6cf 100644
--- a/arch/arm64/boot/dts/marvell/armada-8040-db.dts
+++ b/arch/arm64/boot/dts/marvell/armada-8040-db.dts
@@ -72,7 +72,7 @@
 &spi0 {
 	status = "okay";
 
-	spi-flash@0 {
+	flash@0 {
 		compatible = "jedec,spi-nor";
 		reg = <0>;
 		spi-max-frequency = <10000000>;
@@ -238,7 +238,7 @@
 &cp1_spi1 {
 	status = "okay";
 
-	spi-flash@0 {
+	flash@0 {
 		compatible = "jedec,spi-nor";
 		reg = <0x0>;
 		spi-max-frequency = <20000000>;
diff --git a/arch/arm64/boot/dts/marvell/armada-8040-mcbin.dtsi b/arch/arm64/boot/dts/marvell/armada-8040-mcbin.dtsi
index adbfecc678b5..ca1aeb69a892 100644
--- a/arch/arm64/boot/dts/marvell/armada-8040-mcbin.dtsi
+++ b/arch/arm64/boot/dts/marvell/armada-8040-mcbin.dtsi
@@ -65,10 +65,10 @@
 		/* CON15,16 - CPM lane 4 */
 		compatible = "sff,sfp";
 		i2c-bus = <&sfpp0_i2c>;
-		los-gpio = <&cp1_gpio1 28 GPIO_ACTIVE_HIGH>;
-		mod-def0-gpio = <&cp1_gpio1 27 GPIO_ACTIVE_LOW>;
-		tx-disable-gpio = <&cp1_gpio1 29 GPIO_ACTIVE_HIGH>;
-		tx-fault-gpio  = <&cp1_gpio1 26 GPIO_ACTIVE_HIGH>;
+		los-gpios = <&cp1_gpio1 28 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&cp1_gpio1 27 GPIO_ACTIVE_LOW>;
+		tx-disable-gpios = <&cp1_gpio1 29 GPIO_ACTIVE_HIGH>;
+		tx-fault-gpios = <&cp1_gpio1 26 GPIO_ACTIVE_HIGH>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&cp1_sfpp0_pins>;
 		maximum-power-milliwatt = <2000>;
@@ -78,10 +78,10 @@
 		/* CON17,18 - CPS lane 4 */
 		compatible = "sff,sfp";
 		i2c-bus = <&sfpp1_i2c>;
-		los-gpio = <&cp1_gpio1 8 GPIO_ACTIVE_HIGH>;
-		mod-def0-gpio = <&cp1_gpio1 11 GPIO_ACTIVE_LOW>;
-		tx-disable-gpio = <&cp1_gpio1 10 GPIO_ACTIVE_HIGH>;
-		tx-fault-gpio = <&cp0_gpio2 30 GPIO_ACTIVE_HIGH>;
+		los-gpios = <&cp1_gpio1 8 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&cp1_gpio1 11 GPIO_ACTIVE_LOW>;
+		tx-disable-gpios = <&cp1_gpio1 10 GPIO_ACTIVE_HIGH>;
+		tx-fault-gpios = <&cp0_gpio2 30 GPIO_ACTIVE_HIGH>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&cp1_sfpp1_pins &cp0_sfpp1_pins>;
 		maximum-power-milliwatt = <2000>;
@@ -91,10 +91,10 @@
 		/* CON13,14 - CPS lane 5 */
 		compatible = "sff,sfp";
 		i2c-bus = <&sfp_1g_i2c>;
-		los-gpio = <&cp0_gpio2 22 GPIO_ACTIVE_HIGH>;
-		mod-def0-gpio = <&cp0_gpio2 21 GPIO_ACTIVE_LOW>;
-		tx-disable-gpio = <&cp1_gpio1 24 GPIO_ACTIVE_HIGH>;
-		tx-fault-gpio = <&cp0_gpio2 19 GPIO_ACTIVE_HIGH>;
+		los-gpios = <&cp0_gpio2 22 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&cp0_gpio2 21 GPIO_ACTIVE_LOW>;
+		tx-disable-gpios = <&cp1_gpio1 24 GPIO_ACTIVE_HIGH>;
+		tx-fault-gpios = <&cp0_gpio2 19 GPIO_ACTIVE_HIGH>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&cp0_sfp_1g_pins &cp1_sfp_1g_pins>;
 		maximum-power-milliwatt = <2000>;
@@ -360,7 +360,7 @@
 	pinctrl-0 = <&cp1_spi1_pins>;
 	status = "okay";
 
-	spi-flash@0 {
+	flash@0 {
 		compatible = "st,w25q32";
 		spi-max-frequency = <50000000>;
 		reg = <0>;
diff --git a/arch/arm64/boot/dts/marvell/armada-8040-puzzle-m801.dts b/arch/arm64/boot/dts/marvell/armada-8040-puzzle-m801.dts
index dac85fa748de..eb0473503936 100644
--- a/arch/arm64/boot/dts/marvell/armada-8040-puzzle-m801.dts
+++ b/arch/arm64/boot/dts/marvell/armada-8040-puzzle-m801.dts
@@ -67,20 +67,20 @@
 	sfp_cp0_eth0: sfp-cp0-eth0 {
 		compatible = "sff,sfp";
 		i2c-bus = <&sfpplus0_i2c>;
-		los-gpio = <&sfpplus_gpio 11 GPIO_ACTIVE_HIGH>;
-		mod-def0-gpio = <&sfpplus_gpio 10 GPIO_ACTIVE_LOW>;
-		tx-disable-gpio = <&sfpplus_gpio 9 GPIO_ACTIVE_HIGH>;
-		tx-fault-gpio  = <&sfpplus_gpio 8 GPIO_ACTIVE_HIGH>;
+		los-gpios = <&sfpplus_gpio 11 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&sfpplus_gpio 10 GPIO_ACTIVE_LOW>;
+		tx-disable-gpios = <&sfpplus_gpio 9 GPIO_ACTIVE_HIGH>;
+		tx-fault-gpios = <&sfpplus_gpio 8 GPIO_ACTIVE_HIGH>;
 		maximum-power-milliwatt = <3000>;
 	};
 
 	sfp_cp1_eth0: sfp-cp1-eth0 {
 		compatible = "sff,sfp";
 		i2c-bus = <&sfpplus1_i2c>;
-		los-gpio = <&sfpplus_gpio 3 GPIO_ACTIVE_HIGH>;
-		mod-def0-gpio = <&sfpplus_gpio 2 GPIO_ACTIVE_LOW>;
-		tx-disable-gpio = <&sfpplus_gpio 1 GPIO_ACTIVE_HIGH>;
-		tx-fault-gpio  = <&sfpplus_gpio 0 GPIO_ACTIVE_HIGH>;
+		los-gpios = <&sfpplus_gpio 3 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&sfpplus_gpio 2 GPIO_ACTIVE_LOW>;
+		tx-disable-gpios = <&sfpplus_gpio 1 GPIO_ACTIVE_HIGH>;
+		tx-fault-gpios = <&sfpplus_gpio 0 GPIO_ACTIVE_HIGH>;
 		maximum-power-milliwatt = <3000>;
 	};
 
@@ -185,7 +185,7 @@
 
 &spi0 {
 	status = "okay";
-	spi-flash@0 {
+	flash@0 {
 		#address-cells = <0x1>;
 		#size-cells = <0x1>;
 		compatible = "jedec,spi-nor";
diff --git a/arch/arm64/boot/dts/marvell/armada-ap80x.dtsi b/arch/arm64/boot/dts/marvell/armada-ap80x.dtsi
index 6614472100c2..a06a0a889c43 100644
--- a/arch/arm64/boot/dts/marvell/armada-ap80x.dtsi
+++ b/arch/arm64/boot/dts/marvell/armada-ap80x.dtsi
@@ -250,7 +250,7 @@
 				interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
 			};
 
-			ap_sdhci0: sdhci@6e0000 {
+			ap_sdhci0: mmc@6e0000 {
 				compatible = "marvell,armada-ap806-sdhci";
 				reg = <0x6e0000 0x300>;
 				interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
diff --git a/arch/arm64/boot/dts/marvell/armada-cp11x.dtsi b/arch/arm64/boot/dts/marvell/armada-cp11x.dtsi
index 3bd2182817fb..d6c0990a267d 100644
--- a/arch/arm64/boot/dts/marvell/armada-cp11x.dtsi
+++ b/arch/arm64/boot/dts/marvell/armada-cp11x.dtsi
@@ -493,7 +493,7 @@
 			status = "okay";
 		};
 
-		CP11X_LABEL(sdhci0): sdhci@780000 {
+		CP11X_LABEL(sdhci0): mmc@780000 {
 			compatible = "marvell,armada-cp110-sdhci";
 			reg = <0x780000 0x300>;
 			interrupts = <27 IRQ_TYPE_LEVEL_HIGH>;
diff --git a/arch/arm64/boot/dts/marvell/cn9130-crb.dtsi b/arch/arm64/boot/dts/marvell/cn9130-crb.dtsi
index 505ae69289f6..8e4ec243fb8f 100644
--- a/arch/arm64/boot/dts/marvell/cn9130-crb.dtsi
+++ b/arch/arm64/boot/dts/marvell/cn9130-crb.dtsi
@@ -17,6 +17,8 @@
 		ethernet0 = &cp0_eth0;
 		ethernet1 = &cp0_eth1;
 		ethernet2 = &cp0_eth2;
+		gpio1 = &cp0_gpio1;
+		gpio2 = &cp0_gpio2;
 	};
 
 	memory@0 {
@@ -71,6 +73,17 @@
 		enable-active-high;
 		regulator-always-on;
 	};
+
+	sfp: sfp {
+		compatible = "sff,sfp";
+		i2c-bus = <&cp0_i2c1>;
+		mod-def0-gpios = <&expander0 3 GPIO_ACTIVE_LOW>;
+		los-gpios = <&expander0 15 GPIO_ACTIVE_HIGH>;
+		tx-disable-gpios = <&expander0 2 GPIO_ACTIVE_HIGH>;
+		tx-fault-gpios = <&cp0_gpio1 24 GPIO_ACTIVE_HIGH>;
+		maximum-power-milliwatt = <3000>;
+		status = "okay";
+	};
 };
 
 &uart0 {
@@ -114,6 +127,14 @@
 	};
 };
 
+&cp0_gpio1 {
+	status = "okay";
+};
+
+&cp0_gpio2 {
+	status = "okay";
+};
+
 &cp0_i2c0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&cp0_i2c0_pins>;
@@ -154,7 +175,7 @@
 	      <0x2000000 0x1000000>;	/* CS0 */
 	status = "okay";
 
-	spi-flash@0 {
+	flash@0 {
 		#address-cells = <0x1>;
 		#size-cells = <0x1>;
 		compatible = "jedec,spi-nor";
@@ -185,6 +206,125 @@
 	phy0: ethernet-phy@0 {
 		reg = <0>;
 	};
+
+	switch6: switch0@6 {
+		/* Actual device is MV88E6393X */
+		compatible = "marvell,mv88e6190";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <6>;
+		interrupt-parent = <&cp0_gpio1>;
+		interrupts = <28 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+
+		dsa,member = <0 0>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@1 {
+				reg = <1>;
+				label = "p1";
+				phy-handle = <&switch0phy1>;
+			};
+
+			port@2 {
+				reg = <2>;
+				label = "p2";
+				phy-handle = <&switch0phy2>;
+			};
+
+			port@3 {
+				reg = <3>;
+				label = "p3";
+				phy-handle = <&switch0phy3>;
+			};
+
+			port@4 {
+				reg = <4>;
+				label = "p4";
+				phy-handle = <&switch0phy4>;
+			};
+
+			port@5 {
+				reg = <5>;
+				label = "p5";
+				phy-handle = <&switch0phy5>;
+			};
+
+			port@6 {
+				reg = <6>;
+				label = "p6";
+				phy-handle = <&switch0phy6>;
+			};
+
+			port@7 {
+				reg = <7>;
+				label = "p7";
+				phy-handle = <&switch0phy7>;
+			};
+
+			port@8 {
+				reg = <8>;
+				label = "p8";
+				phy-handle = <&switch0phy8>;
+			};
+
+			port@9 {
+				reg = <9>;
+				label = "p9";
+				phy-mode = "10gbase-r";
+				sfp = <&sfp>;
+				managed = "in-band-status";
+			};
+
+			port@a {
+				reg = <10>;
+				label = "cpu";
+				ethernet = <&cp0_eth0>;
+			};
+
+		};
+
+		mdio {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			switch0phy1: switch0phy1@1 {
+				reg = <0x1>;
+			};
+
+			switch0phy2: switch0phy2@2 {
+				reg = <0x2>;
+			};
+
+			switch0phy3: switch0phy3@3 {
+				reg = <0x3>;
+			};
+
+			switch0phy4: switch0phy4@4 {
+				reg = <0x4>;
+			};
+
+			switch0phy5: switch0phy5@5 {
+				reg = <0x5>;
+			};
+
+			switch0phy6: switch0phy6@6 {
+				reg = <0x6>;
+			};
+
+			switch0phy7: switch0phy7@7 {
+				reg = <0x7>;
+			};
+
+			switch0phy8: switch0phy8@8 {
+				reg = <0x8>;
+			};
+		};
+	};
 };
 
 &cp0_xmdio {
diff --git a/arch/arm64/boot/dts/marvell/cn9130-db.dtsi b/arch/arm64/boot/dts/marvell/cn9130-db.dtsi
index c00b69b88bd2..c7de1ea0d470 100644
--- a/arch/arm64/boot/dts/marvell/cn9130-db.dtsi
+++ b/arch/arm64/boot/dts/marvell/cn9130-db.dtsi
@@ -90,10 +90,10 @@
 	cp0_sfp_eth0: sfp-eth@0 {
 		compatible = "sff,sfp";
 		i2c-bus = <&cp0_sfpp0_i2c>;
-		los-gpio = <&cp0_module_expander1 11 GPIO_ACTIVE_HIGH>;
-		mod-def0-gpio = <&cp0_module_expander1 10 GPIO_ACTIVE_LOW>;
-		tx-disable-gpio = <&cp0_module_expander1 9 GPIO_ACTIVE_HIGH>;
-		tx-fault-gpio = <&cp0_module_expander1 8 GPIO_ACTIVE_HIGH>;
+		los-gpios = <&cp0_module_expander1 11 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&cp0_module_expander1 10 GPIO_ACTIVE_LOW>;
+		tx-disable-gpios = <&cp0_module_expander1 9 GPIO_ACTIVE_HIGH>;
+		tx-fault-gpios = <&cp0_module_expander1 8 GPIO_ACTIVE_HIGH>;
 		/*
 		 * SFP cages are unconnected on early PCBs because of an the I2C
 		 * lanes not being connected. Prevent the port for being
@@ -310,7 +310,7 @@
 	pinctrl-0 = <&cp0_spi0_pins>;
 	reg = <0x700680 0x50>;
 
-	spi-flash@0 {
+	flash@0 {
 		#address-cells = <0x1>;
 		#size-cells = <0x1>;
 		compatible = "jedec,spi-nor";
@@ -404,7 +404,7 @@
 &cp0_usb3_1 {
 	status = "okay";
 	usb-phy = <&cp0_usb3_0_phy1>;
-	phys =  <&cp0_utmi1>;
+	phys = <&cp0_utmi1>;
 	phy-names = "utmi";
 	dr_mode = "host";
 };
diff --git a/arch/arm64/boot/dts/marvell/cn9130.dtsi b/arch/arm64/boot/dts/marvell/cn9130.dtsi
index a2b7e5ec979d..327b04134134 100644
--- a/arch/arm64/boot/dts/marvell/cn9130.dtsi
+++ b/arch/arm64/boot/dts/marvell/cn9130.dtsi
@@ -11,6 +11,13 @@
 	model = "Marvell Armada CN9130 SoC";
 	compatible = "marvell,cn9130", "marvell,armada-ap807-quad",
 		     "marvell,armada-ap807";
+
+	aliases {
+		gpio1 = &cp0_gpio1;
+		gpio2 = &cp0_gpio2;
+		spi1 = &cp0_spi0;
+		spi2 = &cp0_spi1;
+	};
 };
 
 /*
@@ -35,3 +42,11 @@
 #undef CP11X_PCIE0_BASE
 #undef CP11X_PCIE1_BASE
 #undef CP11X_PCIE2_BASE
+
+&cp0_gpio1 {
+	status = "okay";
+};
+
+&cp0_gpio2 {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/marvell/cn9131-db.dtsi b/arch/arm64/boot/dts/marvell/cn9131-db.dtsi
index f995b1bcda01..ff8422fae31b 100644
--- a/arch/arm64/boot/dts/marvell/cn9131-db.dtsi
+++ b/arch/arm64/boot/dts/marvell/cn9131-db.dtsi
@@ -37,10 +37,10 @@
 	cp1_sfp_eth1: sfp-eth1 {
 		compatible = "sff,sfp";
 		i2c-bus = <&cp1_i2c0>;
-		los-gpio = <&cp1_gpio1 11 GPIO_ACTIVE_HIGH>;
-		mod-def0-gpio = <&cp1_gpio1 10 GPIO_ACTIVE_LOW>;
-		tx-disable-gpio = <&cp1_gpio1 9 GPIO_ACTIVE_HIGH>;
-		tx-fault-gpio = <&cp1_gpio1 8 GPIO_ACTIVE_HIGH>;
+		los-gpios = <&cp1_gpio1 11 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&cp1_gpio1 10 GPIO_ACTIVE_LOW>;
+		tx-disable-gpios = <&cp1_gpio1 9 GPIO_ACTIVE_HIGH>;
+		tx-fault-gpios = <&cp1_gpio1 8 GPIO_ACTIVE_HIGH>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&cp1_sfp_pins>;
 		/*
@@ -137,7 +137,7 @@
 	pinctrl-0 = <&cp1_spi0_pins>;
 	reg = <0x700680 0x50>;
 
-	spi-flash@0 {
+	flash@0 {
 		#address-cells = <0x1>;
 		#size-cells = <0x1>;
 		compatible = "jedec,spi-nor";
diff --git a/arch/arm64/boot/dts/marvell/cn9132-db.dtsi b/arch/arm64/boot/dts/marvell/cn9132-db.dtsi
index 3f1795fb4fe7..512a4fa2861e 100644
--- a/arch/arm64/boot/dts/marvell/cn9132-db.dtsi
+++ b/arch/arm64/boot/dts/marvell/cn9132-db.dtsi
@@ -57,10 +57,10 @@
 	cp2_sfp_eth0: sfp-eth0 {
 		compatible = "sff,sfp";
 		i2c-bus = <&cp2_sfpp0_i2c>;
-		los-gpio = <&cp2_module_expander1 11 GPIO_ACTIVE_HIGH>;
-		mod-def0-gpio = <&cp2_module_expander1 10 GPIO_ACTIVE_LOW>;
-		tx-disable-gpio = <&cp2_module_expander1 9 GPIO_ACTIVE_HIGH>;
-		tx-fault-gpio = <&cp2_module_expander1 8 GPIO_ACTIVE_HIGH>;
+		los-gpios = <&cp2_module_expander1 11 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&cp2_module_expander1 10 GPIO_ACTIVE_LOW>;
+		tx-disable-gpios = <&cp2_module_expander1 9 GPIO_ACTIVE_HIGH>;
+		tx-fault-gpios = <&cp2_module_expander1 8 GPIO_ACTIVE_HIGH>;
 		/*
 		 * SFP cages are unconnected on early PCBs because of an the I2C
 		 * lanes not being connected. Prevent the port for being
diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile
index 4f68ebed2e31..0ec90cb3ef28 100644
--- a/arch/arm64/boot/dts/mediatek/Makefile
+++ b/arch/arm64/boot/dts/mediatek/Makefile
@@ -7,6 +7,8 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt6797-evb.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt6797-x20-dev.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-rfb1.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-bananapi-bpi-r64.dtb
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-rfb.dtb
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986b-rfb.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt8167-pumpkin.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-elm.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-elm-hana.dtb
@@ -14,16 +16,20 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-elm-hana-rev7.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt8173-evb.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-evb.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-jacuzzi-burnet.dtb
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-jacuzzi-cozmo.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-jacuzzi-damu.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-jacuzzi-fennel-sku1.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-jacuzzi-fennel-sku6.dtb
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-jacuzzi-fennel-sku7.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-jacuzzi-fennel14.dtb
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-jacuzzi-fennel14-sku2.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-jacuzzi-juniper-sku16.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-jacuzzi-kappa.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-jacuzzi-kenzo.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-jacuzzi-willow-sku0.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-jacuzzi-willow-sku1.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-kakadu.dtb
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-kakadu-sku22.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-kodama-sku16.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-kodama-sku272.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-kodama-sku288.dtb
@@ -31,5 +37,13 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-kodama-sku32.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-krane-sku0.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-kukui-krane-sku176.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt8183-pumpkin.dtb
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt8186-evb.dtb
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt8192-asurada-hayato-r1.dtb
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt8192-asurada-spherion-r0.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt8192-evb.dtb
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-cherry-tomato-r1.dtb
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-cherry-tomato-r2.dtb
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-cherry-tomato-r3.dtb
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-demo.dtb
+dtb-$(CONFIG_ARCH_MEDIATEK) += mt8195-evb.dtb
 dtb-$(CONFIG_ARCH_MEDIATEK) += mt8516-pumpkin.dtb
diff --git a/arch/arm64/boot/dts/mediatek/mt2712-evb.dts b/arch/arm64/boot/dts/mediatek/mt2712-evb.dts
index 7d369fdd3117..9b1af9c80130 100644
--- a/arch/arm64/boot/dts/mediatek/mt2712-evb.dts
+++ b/arch/arm64/boot/dts/mediatek/mt2712-evb.dts
@@ -106,10 +106,11 @@
 };
 
 &eth {
-	phy-mode ="rgmii-rxid";
+	phy-mode = "rgmii-rxid";
 	phy-handle = <&ethernet_phy0>;
 	mediatek,tx-delay-ps = <1530>;
 	snps,reset-gpio = <&pio 87 GPIO_ACTIVE_LOW>;
+	snps,reset-delays-us = <0 10000 10000>;
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&eth_default>;
 	pinctrl-1 = <&eth_sleep>;
diff --git a/arch/arm64/boot/dts/mediatek/mt2712e.dtsi b/arch/arm64/boot/dts/mediatek/mt2712e.dtsi
index de16c0d80c30..e6d7453e56e0 100644
--- a/arch/arm64/boot/dts/mediatek/mt2712e.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt2712e.dtsi
@@ -19,7 +19,7 @@
 	#address-cells = <2>;
 	#size-cells = <2>;
 
-	cluster0_opp: opp_table0 {
+	cluster0_opp: opp-table-0 {
 		compatible = "operating-points-v2";
 		opp-shared;
 		opp00 {
@@ -36,7 +36,7 @@
 		};
 	};
 
-	cluster1_opp: opp_table1 {
+	cluster1_opp: opp-table-1 {
 		compatible = "operating-points-v2";
 		opp-shared;
 		opp00 {
@@ -329,8 +329,9 @@
 		interrupts = <GIC_SPI 147 IRQ_TYPE_LEVEL_LOW>;
 		clocks = <&infracfg CLK_INFRA_M4U>;
 		clock-names = "bclk";
-		mediatek,larbs = <&larb0 &larb1 &larb2
-				  &larb3 &larb6>;
+		mediatek,infracfg = <&infracfg>;
+		mediatek,larbs = <&larb0>, <&larb1>, <&larb2>,
+				 <&larb3>, <&larb6>;
 		#iommu-cells = <1>;
 	};
 
@@ -346,7 +347,8 @@
 		interrupts = <GIC_SPI 145 IRQ_TYPE_LEVEL_LOW>;
 		clocks = <&infracfg CLK_INFRA_M4U>;
 		clock-names = "bclk";
-		mediatek,larbs = <&larb4 &larb5 &larb7>;
+		mediatek,infracfg = <&infracfg>;
+		mediatek,larbs = <&larb4>, <&larb5>, <&larb7>;
 		#iommu-cells = <1>;
 	};
 
@@ -726,7 +728,7 @@
 	};
 
 	eth: ethernet@1101c000 {
-		compatible = "mediatek,mt2712-gmac";
+		compatible = "mediatek,mt2712-gmac", "snps,dwmac-4.20a";
 		reg = <0 0x1101c000 0 0x1300>;
 		interrupts = <GIC_SPI 237 IRQ_TYPE_LEVEL_LOW>;
 		interrupt-names = "macirq";
@@ -734,15 +736,19 @@
 		clock-names = "axi",
 			      "apb",
 			      "mac_main",
-			      "ptp_ref";
+			      "ptp_ref",
+			      "rmii_internal";
 		clocks = <&pericfg CLK_PERI_GMAC>,
 			 <&pericfg CLK_PERI_GMAC_PCLK>,
 			 <&topckgen CLK_TOP_ETHER_125M_SEL>,
-			 <&topckgen CLK_TOP_ETHER_50M_SEL>;
+			 <&topckgen CLK_TOP_ETHER_50M_SEL>,
+			 <&topckgen CLK_TOP_ETHER_50M_RMII_SEL>;
 		assigned-clocks = <&topckgen CLK_TOP_ETHER_125M_SEL>,
-				  <&topckgen CLK_TOP_ETHER_50M_SEL>;
+				  <&topckgen CLK_TOP_ETHER_50M_SEL>,
+				  <&topckgen CLK_TOP_ETHER_50M_RMII_SEL>;
 		assigned-clock-parents = <&topckgen CLK_TOP_ETHERPLL_125M>,
-					 <&topckgen CLK_TOP_APLL1_D3>;
+					 <&topckgen CLK_TOP_APLL1_D3>,
+					 <&topckgen CLK_TOP_ETHERPLL_50M>;
 		power-domains = <&scpsys MT2712_POWER_DOMAIN_AUDIO>;
 		mediatek,pericfg = <&pericfg>;
 		snps,axi-config = <&stmmac_axi_setup>;
@@ -750,7 +756,7 @@
 		snps,mtl-tx-config = <&mtl_tx_setup>;
 		snps,txpbl = <1>;
 		snps,rxpbl = <1>;
-		clk_csr = <0>;
+		snps,clk-csr = <0>;
 		status = "disabled";
 	};
 
diff --git a/arch/arm64/boot/dts/mediatek/mt6358.dtsi b/arch/arm64/boot/dts/mediatek/mt6358.dtsi
index 95145076b7e6..98f3b0e0c9f6 100644
--- a/arch/arm64/boot/dts/mediatek/mt6358.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt6358.dtsi
@@ -2,6 +2,7 @@
 /*
  * Copyright (c) 2020 MediaTek Inc.
  */
+#include <dt-bindings/input/input.h>
 
 &pwrap {
 	pmic: mt6358 {
@@ -357,5 +358,16 @@
 		mt6358rtc: mt6358rtc {
 			compatible = "mediatek,mt6358-rtc";
 		};
+
+		mt6358keys: mt6358keys {
+			compatible = "mediatek,mt6358-keys";
+			power {
+				linux,keycodes = <KEY_POWER>;
+				wakeup-source;
+			};
+			home {
+				linux,keycodes = <KEY_HOME>;
+			};
+		};
 	};
 };
diff --git a/arch/arm64/boot/dts/mediatek/mt6359.dtsi b/arch/arm64/boot/dts/mediatek/mt6359.dtsi
new file mode 100644
index 000000000000..df3e822232d3
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt6359.dtsi
@@ -0,0 +1,298 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright (C) 2022 MediaTek Inc.
+ */
+
+&pwrap {
+	pmic: pmic {
+		compatible = "mediatek,mt6359";
+		interrupt-controller;
+		#interrupt-cells = <2>;
+
+		mt6359codec: mt6359codec {
+		};
+
+		regulators {
+			mt6359_vs1_buck_reg: buck_vs1 {
+				regulator-name = "vs1";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <2200000>;
+				regulator-enable-ramp-delay = <0>;
+				regulator-always-on;
+			};
+			mt6359_vgpu11_buck_reg: buck_vgpu11 {
+				regulator-name = "vgpu11";
+				regulator-min-microvolt = <400000>;
+				regulator-max-microvolt = <1193750>;
+				regulator-ramp-delay = <5000>;
+				regulator-enable-ramp-delay = <200>;
+				regulator-allowed-modes = <0 1 2>;
+			};
+			mt6359_vmodem_buck_reg: buck_vmodem {
+				regulator-name = "vmodem";
+				regulator-min-microvolt = <400000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-ramp-delay = <10760>;
+				regulator-enable-ramp-delay = <200>;
+			};
+			mt6359_vpu_buck_reg: buck_vpu {
+				regulator-name = "vpu";
+				regulator-min-microvolt = <400000>;
+				regulator-max-microvolt = <1193750>;
+				regulator-ramp-delay = <5000>;
+				regulator-enable-ramp-delay = <200>;
+				regulator-allowed-modes = <0 1 2>;
+			};
+			mt6359_vcore_buck_reg: buck_vcore {
+				regulator-name = "vcore";
+				regulator-min-microvolt = <400000>;
+				regulator-max-microvolt = <1300000>;
+				regulator-ramp-delay = <5000>;
+				regulator-enable-ramp-delay = <200>;
+				regulator-allowed-modes = <0 1 2>;
+			};
+			mt6359_vs2_buck_reg: buck_vs2 {
+				regulator-name = "vs2";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1600000>;
+				regulator-enable-ramp-delay = <0>;
+				regulator-always-on;
+			};
+			mt6359_vpa_buck_reg: buck_vpa {
+				regulator-name = "vpa";
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <3650000>;
+				regulator-enable-ramp-delay = <300>;
+			};
+			mt6359_vproc2_buck_reg: buck_vproc2 {
+				regulator-name = "vproc2";
+				regulator-min-microvolt = <400000>;
+				regulator-max-microvolt = <1193750>;
+				regulator-ramp-delay = <7500>;
+				regulator-enable-ramp-delay = <200>;
+				regulator-allowed-modes = <0 1 2>;
+			};
+			mt6359_vproc1_buck_reg: buck_vproc1 {
+				regulator-name = "vproc1";
+				regulator-min-microvolt = <400000>;
+				regulator-max-microvolt = <1193750>;
+				regulator-ramp-delay = <7500>;
+				regulator-enable-ramp-delay = <200>;
+				regulator-allowed-modes = <0 1 2>;
+			};
+			mt6359_vcore_sshub_buck_reg: buck_vcore_sshub {
+				regulator-name = "vcore_sshub";
+				regulator-min-microvolt = <400000>;
+				regulator-max-microvolt = <1193750>;
+			};
+			mt6359_vgpu11_sshub_buck_reg: buck_vgpu11_sshub {
+				regulator-name = "vgpu11_sshub";
+				regulator-min-microvolt = <400000>;
+				regulator-max-microvolt = <1193750>;
+			};
+			mt6359_vaud18_ldo_reg: ldo_vaud18 {
+				regulator-name = "vaud18";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-enable-ramp-delay = <240>;
+			};
+			mt6359_vsim1_ldo_reg: ldo_vsim1 {
+				regulator-name = "vsim1";
+				regulator-min-microvolt = <1700000>;
+				regulator-max-microvolt = <3100000>;
+			};
+			mt6359_vibr_ldo_reg: ldo_vibr {
+				regulator-name = "vibr";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <3300000>;
+			};
+			mt6359_vrf12_ldo_reg: ldo_vrf12 {
+				regulator-name = "vrf12";
+				regulator-min-microvolt = <1100000>;
+				regulator-max-microvolt = <1300000>;
+			};
+			mt6359_vusb_ldo_reg: ldo_vusb {
+				regulator-name = "vusb";
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-enable-ramp-delay = <960>;
+				regulator-always-on;
+			};
+			mt6359_vsram_proc2_ldo_reg: ldo_vsram_proc2 {
+				regulator-name = "vsram_proc2";
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <1293750>;
+				regulator-ramp-delay = <7500>;
+				regulator-enable-ramp-delay = <240>;
+				regulator-always-on;
+			};
+			mt6359_vio18_ldo_reg: ldo_vio18 {
+				regulator-name = "vio18";
+				regulator-min-microvolt = <1700000>;
+				regulator-max-microvolt = <1900000>;
+				regulator-enable-ramp-delay = <960>;
+				regulator-always-on;
+			};
+			mt6359_vcamio_ldo_reg: ldo_vcamio {
+				regulator-name = "vcamio";
+				regulator-min-microvolt = <1700000>;
+				regulator-max-microvolt = <1900000>;
+			};
+			mt6359_vcn18_ldo_reg: ldo_vcn18 {
+				regulator-name = "vcn18";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-enable-ramp-delay = <240>;
+			};
+			mt6359_vfe28_ldo_reg: ldo_vfe28 {
+				regulator-name = "vfe28";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+				regulator-enable-ramp-delay = <120>;
+			};
+			mt6359_vcn13_ldo_reg: ldo_vcn13 {
+				regulator-name = "vcn13";
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <1300000>;
+			};
+			mt6359_vcn33_1_bt_ldo_reg: ldo_vcn33_1_bt {
+				regulator-name = "vcn33_1_bt";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <3500000>;
+			};
+			mt6359_vcn33_1_wifi_ldo_reg: ldo_vcn33_1_wifi {
+				regulator-name = "vcn33_1_wifi";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <3500000>;
+			};
+			mt6359_vaux18_ldo_reg: ldo_vaux18 {
+				regulator-name = "vaux18";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-enable-ramp-delay = <240>;
+				regulator-always-on;
+			};
+			mt6359_vsram_others_ldo_reg: ldo_vsram_others {
+				regulator-name = "vsram_others";
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <1293750>;
+				regulator-ramp-delay = <5000>;
+				regulator-enable-ramp-delay = <240>;
+			};
+			mt6359_vefuse_ldo_reg: ldo_vefuse {
+				regulator-name = "vefuse";
+				regulator-min-microvolt = <1700000>;
+				regulator-max-microvolt = <2000000>;
+			};
+			mt6359_vxo22_ldo_reg: ldo_vxo22 {
+				regulator-name = "vxo22";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <2200000>;
+				regulator-always-on;
+			};
+			mt6359_vrfck_ldo_reg: ldo_vrfck {
+				regulator-name = "vrfck";
+				regulator-min-microvolt = <1500000>;
+				regulator-max-microvolt = <1700000>;
+			};
+			mt6359_vrfck_1_ldo_reg: ldo_vrfck_1 {
+				regulator-name = "vrfck";
+				regulator-min-microvolt = <1240000>;
+				regulator-max-microvolt = <1600000>;
+			};
+			mt6359_vbif28_ldo_reg: ldo_vbif28 {
+				regulator-name = "vbif28";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+				regulator-enable-ramp-delay = <240>;
+			};
+			mt6359_vio28_ldo_reg: ldo_vio28 {
+				regulator-name = "vio28";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-always-on;
+			};
+			mt6359_vemc_ldo_reg: ldo_vemc {
+				regulator-name = "vemc";
+				regulator-min-microvolt = <2900000>;
+				regulator-max-microvolt = <3300000>;
+			};
+			mt6359_vemc_1_ldo_reg: ldo_vemc_1 {
+				regulator-name = "vemc";
+				regulator-min-microvolt = <2500000>;
+				regulator-max-microvolt = <3300000>;
+			};
+			mt6359_vcn33_2_bt_ldo_reg: ldo_vcn33_2_bt {
+				regulator-name = "vcn33_2_bt";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <3500000>;
+			};
+			mt6359_vcn33_2_wifi_ldo_reg: ldo_vcn33_2_wifi {
+				regulator-name = "vcn33_2_wifi";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <3500000>;
+			};
+			mt6359_va12_ldo_reg: ldo_va12 {
+				regulator-name = "va12";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1300000>;
+				regulator-always-on;
+			};
+			mt6359_va09_ldo_reg: ldo_va09 {
+				regulator-name = "va09";
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1200000>;
+			};
+			mt6359_vrf18_ldo_reg: ldo_vrf18 {
+				regulator-name = "vrf18";
+				regulator-min-microvolt = <1700000>;
+				regulator-max-microvolt = <1810000>;
+			};
+			mt6359_vsram_md_ldo_reg: ldo_vsram_md {
+				regulator-name = "vsram_md";
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <1293750>;
+				regulator-ramp-delay = <10760>;
+				regulator-enable-ramp-delay = <240>;
+			};
+			mt6359_vufs_ldo_reg: ldo_vufs {
+				regulator-name = "vufs";
+				regulator-min-microvolt = <1700000>;
+				regulator-max-microvolt = <1900000>;
+			};
+			mt6359_vm18_ldo_reg: ldo_vm18 {
+				regulator-name = "vm18";
+				regulator-min-microvolt = <1700000>;
+				regulator-max-microvolt = <1900000>;
+				regulator-always-on;
+			};
+			mt6359_vbbck_ldo_reg: ldo_vbbck {
+				regulator-name = "vbbck";
+				regulator-min-microvolt = <1100000>;
+				regulator-max-microvolt = <1200000>;
+			};
+			mt6359_vsram_proc1_ldo_reg: ldo_vsram_proc1 {
+				regulator-name = "vsram_proc1";
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <1293750>;
+				regulator-ramp-delay = <7500>;
+				regulator-enable-ramp-delay = <240>;
+				regulator-always-on;
+			};
+			mt6359_vsim2_ldo_reg: ldo_vsim2 {
+				regulator-name = "vsim2";
+				regulator-min-microvolt = <1700000>;
+				regulator-max-microvolt = <3100000>;
+			};
+			mt6359_vsram_others_sshub_ldo: ldo_vsram_others_sshub {
+				regulator-name = "vsram_others_sshub";
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <1293750>;
+			};
+		};
+
+		mt6359rtc: mt6359rtc {
+			compatible = "mediatek,mt6358-rtc";
+		};
+	};
+};
diff --git a/arch/arm64/boot/dts/mediatek/mt6755.dtsi b/arch/arm64/boot/dts/mediatek/mt6755.dtsi
index 01ba77669717..b55d3fac9bd4 100644
--- a/arch/arm64/boot/dts/mediatek/mt6755.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt6755.dtsi
@@ -1,14 +1,7 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Copyright (c) 2016 MediaTek Inc.
  * Author: Mars.C <mars.cheng@mediatek.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- * This program is distributed in the hope that it will be useful,
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
  */
 
 #include <dt-bindings/interrupt-controller/irq.h>
diff --git a/arch/arm64/boot/dts/mediatek/mt6795.dtsi b/arch/arm64/boot/dts/mediatek/mt6795.dtsi
index c85659d0ff5d..46f0e54be766 100644
--- a/arch/arm64/boot/dts/mediatek/mt6795.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt6795.dtsi
@@ -1,18 +1,12 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Copyright (c) 2015 MediaTek Inc.
  * Author: Mars.C <mars.cheng@mediatek.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- * This program is distributed in the hope that it will be useful,
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
  */
 
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/pinctrl/mt6795-pinfunc.h>
 
 / {
 	compatible = "mediatek,mt6795";
@@ -34,6 +28,8 @@
 			compatible = "arm,cortex-a53";
 			enable-method = "psci";
 			reg = <0x000>;
+			cci-control-port = <&cci_control2>;
+			next-level-cache = <&l2_0>;
 		};
 
 		cpu1: cpu@1 {
@@ -41,6 +37,8 @@
 			compatible = "arm,cortex-a53";
 			enable-method = "psci";
 			reg = <0x001>;
+			cci-control-port = <&cci_control2>;
+			next-level-cache = <&l2_0>;
 		};
 
 		cpu2: cpu@2 {
@@ -48,6 +46,8 @@
 			compatible = "arm,cortex-a53";
 			enable-method = "psci";
 			reg = <0x002>;
+			cci-control-port = <&cci_control2>;
+			next-level-cache = <&l2_0>;
 		};
 
 		cpu3: cpu@3 {
@@ -55,6 +55,8 @@
 			compatible = "arm,cortex-a53";
 			enable-method = "psci";
 			reg = <0x003>;
+			cci-control-port = <&cci_control2>;
+			next-level-cache = <&l2_0>;
 		};
 
 		cpu4: cpu@100 {
@@ -62,6 +64,8 @@
 			compatible = "arm,cortex-a53";
 			enable-method = "psci";
 			reg = <0x100>;
+			cci-control-port = <&cci_control1>;
+			next-level-cache = <&l2_1>;
 		};
 
 		cpu5: cpu@101 {
@@ -69,6 +73,8 @@
 			compatible = "arm,cortex-a53";
 			enable-method = "psci";
 			reg = <0x101>;
+			cci-control-port = <&cci_control1>;
+			next-level-cache = <&l2_1>;
 		};
 
 		cpu6: cpu@102 {
@@ -76,6 +82,8 @@
 			compatible = "arm,cortex-a53";
 			enable-method = "psci";
 			reg = <0x102>;
+			cci-control-port = <&cci_control1>;
+			next-level-cache = <&l2_1>;
 		};
 
 		cpu7: cpu@103 {
@@ -83,27 +91,88 @@
 			compatible = "arm,cortex-a53";
 			enable-method = "psci";
 			reg = <0x103>;
+			cci-control-port = <&cci_control1>;
+			next-level-cache = <&l2_1>;
+		};
+
+		cpu-map {
+			cluster0 {
+				core0 {
+					cpu = <&cpu0>;
+				};
+
+				core1 {
+					cpu = <&cpu1>;
+				};
+
+				core2 {
+					cpu = <&cpu2>;
+				};
+
+				core3 {
+					cpu = <&cpu3>;
+				};
+			};
+
+			cluster1 {
+				core0 {
+					cpu = <&cpu4>;
+				};
+
+				core1 {
+					cpu = <&cpu5>;
+				};
+
+				core2 {
+					cpu = <&cpu6>;
+				};
+
+				core3 {
+					cpu = <&cpu7>;
+				};
+			};
+		};
+
+		l2_0: l2-cache0 {
+			compatible = "cache";
+			cache-level = <2>;
+		};
+
+		l2_1: l2-cache1 {
+			compatible = "cache";
+			cache-level = <2>;
 		};
 	};
 
-	system_clk: dummy13m {
+	clk26m: oscillator-26m {
 		compatible = "fixed-clock";
-		clock-frequency = <13000000>;
 		#clock-cells = <0>;
+		clock-frequency = <26000000>;
+		clock-output-names = "clk26m";
 	};
 
-	rtc_clk: dummy32k {
+	clk32k: oscillator-32k {
 		compatible = "fixed-clock";
-		clock-frequency = <32000>;
 		#clock-cells = <0>;
+		clock-frequency = <32000>;
+		clock-output-names = "clk32k";
 	};
 
-	uart_clk: dummy26m {
+	system_clk: dummy13m {
 		compatible = "fixed-clock";
-		clock-frequency = <26000000>;
+		clock-frequency = <13000000>;
 		#clock-cells = <0>;
 	};
 
+	pmu {
+		compatible = "arm,cortex-a53-pmu";
+		interrupts = <GIC_SPI  8 IRQ_TYPE_LEVEL_LOW>,
+			     <GIC_SPI  9 IRQ_TYPE_LEVEL_LOW>,
+			     <GIC_SPI 10 IRQ_TYPE_LEVEL_LOW>,
+			     <GIC_SPI 11 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>;
+	};
+
 	timer {
 		compatible = "arm,armv8-timer";
 		interrupt-parent = <&gic>;
@@ -117,59 +186,141 @@
 			     (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>;
 	};
 
-	sysirq: intpol-controller@10200620 {
-		compatible = "mediatek,mt6795-sysirq",
-			     "mediatek,mt6577-sysirq";
-		interrupt-controller;
-		#interrupt-cells = <3>;
-		interrupt-parent = <&gic>;
-		reg = <0 0x10200620 0 0x20>;
-	};
+	soc {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		compatible = "simple-bus";
+		ranges;
 
-	gic: interrupt-controller@10221000 {
-		compatible = "arm,gic-400";
-		#interrupt-cells = <3>;
-		interrupt-parent = <&gic>;
-		interrupt-controller;
-		reg = <0 0x10221000 0 0x1000>,
-		      <0 0x10222000 0 0x2000>,
-		      <0 0x10224000 0 0x2000>,
-		      <0 0x10226000 0 0x2000>;
-	};
+		pio: pinctrl@10005000 {
+			compatible = "mediatek,mt6795-pinctrl";
+			reg = <0 0x10005000 0 0x1000>, <0 0x1000b000 0 0x1000>;
+			reg-names = "base", "eint";
+			interrupts = <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&pio 0 0 196>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
 
-	uart0: serial@11002000 {
-		compatible = "mediatek,mt6795-uart",
-			     "mediatek,mt6577-uart";
-		reg = <0 0x11002000 0 0x400>;
-		interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_LOW>;
-		clocks = <&uart_clk>;
-		status = "disabled";
-	};
+		watchdog: watchdog@10007000 {
+			compatible = "mediatek,mt6795-wdt";
+			reg = <0 0x10007000 0 0x100>;
+			interrupts = <GIC_SPI 128 IRQ_TYPE_LEVEL_LOW>;
+			#reset-cells = <1>;
+			timeout-sec = <20>;
+		};
 
-	uart1: serial@11003000 {
-		compatible = "mediatek,mt6795-uart",
-			     "mediatek,mt6577-uart";
-		reg = <0 0x11003000 0 0x400>;
-		interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_LOW>;
-		clocks = <&uart_clk>;
-		status = "disabled";
-	};
+		timer: timer@10008000 {
+			compatible = "mediatek,mt6795-timer",
+				     "mediatek,mt6577-timer";
+			reg = <0 0x10008000 0 0x1000>;
+			interrupts = <GIC_SPI 152 IRQ_TYPE_LEVEL_LOW>;
+			clocks = <&system_clk>, <&clk32k>;
+		};
 
-	uart2: serial@11004000 {
-		compatible = "mediatek,mt6795-uart",
-			     "mediatek,mt6577-uart";
-		reg = <0 0x11004000 0 0x400>;
-		interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_LOW>;
-		clocks = <&uart_clk>;
-		status = "disabled";
-	};
+		sysirq: intpol-controller@10200620 {
+			compatible = "mediatek,mt6795-sysirq",
+				     "mediatek,mt6577-sysirq";
+			interrupt-controller;
+			#interrupt-cells = <3>;
+			interrupt-parent = <&gic>;
+			reg = <0 0x10200620 0 0x20>;
+		};
+
+		systimer: timer@10200670 {
+			compatible = "mediatek,mt6795-systimer";
+			reg = <0 0x10200670 0 0x10>;
+			interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&system_clk>;
+			clock-names = "clk13m";
+		};
+
+		gic: interrupt-controller@10221000 {
+			compatible = "arm,gic-400";
+			#interrupt-cells = <3>;
+			interrupt-parent = <&gic>;
+			interrupt-controller;
+			reg = <0 0x10221000 0 0x1000>,
+			      <0 0x10222000 0 0x2000>,
+			      <0 0x10224000 0 0x2000>,
+			      <0 0x10226000 0 0x2000>;
+			interrupts = <GIC_PPI 9
+				(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+		};
+
+		cci: cci@10390000 {
+			compatible = "arm,cci-400";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			reg = <0 0x10390000 0 0x1000>;
+			ranges = <0 0 0x10390000 0x10000>;
 
-	uart3: serial@11005000 {
-		compatible = "mediatek,mt6795-uart",
-			     "mediatek,mt6577-uart";
-		reg = <0 0x11005000 0 0x400>;
-		interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_LOW>;
-		clocks = <&uart_clk>;
-		status = "disabled";
+			cci_control0: slave-if@1000 {
+				compatible = "arm,cci-400-ctrl-if";
+				interface-type = "ace-lite";
+				reg = <0x1000 0x1000>;
+			};
+
+			cci_control1: slave-if@4000 {
+				compatible = "arm,cci-400-ctrl-if";
+				interface-type = "ace";
+				reg = <0x4000 0x1000>;
+			};
+
+			cci_control2: slave-if@5000 {
+				compatible = "arm,cci-400-ctrl-if";
+				interface-type = "ace";
+				reg = <0x5000 0x1000>;
+			};
+
+			pmu@9000 {
+				compatible = "arm,cci-400-pmu,r1";
+				reg = <0x9000 0x5000>;
+				interrupts = <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
+			};
+		};
+
+		uart0: serial@11002000 {
+			compatible = "mediatek,mt6795-uart",
+				     "mediatek,mt6577-uart";
+			reg = <0 0x11002000 0 0x400>;
+			interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_LOW>;
+			clocks = <&clk26m>;
+			status = "disabled";
+		};
+
+		uart1: serial@11003000 {
+			compatible = "mediatek,mt6795-uart",
+				     "mediatek,mt6577-uart";
+			reg = <0 0x11003000 0 0x400>;
+			interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_LOW>;
+			clocks = <&clk26m>;
+			status = "disabled";
+		};
+
+		uart2: serial@11004000 {
+			compatible = "mediatek,mt6795-uart",
+				     "mediatek,mt6577-uart";
+			reg = <0 0x11004000 0 0x400>;
+			interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_LOW>;
+			clocks = <&clk26m>;
+			status = "disabled";
+		};
+
+		uart3: serial@11005000 {
+			compatible = "mediatek,mt6795-uart",
+				     "mediatek,mt6577-uart";
+			reg = <0 0x11005000 0 0x400>;
+			interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_LOW>;
+			clocks = <&clk26m>;
+			status = "disabled";
+		};
 	};
 };
diff --git a/arch/arm64/boot/dts/mediatek/mt7622-bananapi-bpi-r64.dts b/arch/arm64/boot/dts/mediatek/mt7622-bananapi-bpi-r64.dts
index 2b9bf8dd14ec..d3f9eab2b784 100644
--- a/arch/arm64/boot/dts/mediatek/mt7622-bananapi-bpi-r64.dts
+++ b/arch/arm64/boot/dts/mediatek/mt7622-bananapi-bpi-r64.dts
@@ -8,6 +8,7 @@
 /dts-v1/;
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
 
 #include "mt7622.dtsi"
 #include "mt6380.dtsi"
@@ -40,30 +41,32 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		factory {
+		factory-key {
 			label = "factory";
 			linux,code = <BTN_0>;
 			gpios = <&pio 0 GPIO_ACTIVE_HIGH>;
 		};
 
-		wps {
+		wps-key {
 			label = "wps";
 			linux,code = <KEY_WPS_BUTTON>;
-			gpios = <&pio 102 GPIO_ACTIVE_HIGH>;
+			gpios = <&pio 102 GPIO_ACTIVE_LOW>;
 		};
 	};
 
 	leds {
 		compatible = "gpio-leds";
 
-		green {
+		led-0 {
 			label = "bpi-r64:pio:green";
+			color = <LED_COLOR_ID_GREEN>;
 			gpios = <&pio 89 GPIO_ACTIVE_HIGH>;
 			default-state = "off";
 		};
 
-		red {
+		led-1 {
 			label = "bpi-r64:pio:red";
+			color = <LED_COLOR_ID_RED>;
 			gpios = <&pio 88 GPIO_ACTIVE_HIGH>;
 			default-state = "off";
 		};
@@ -336,14 +339,14 @@
 	i2c1_pins: i2c1-pins {
 		mux {
 			function = "i2c";
-			groups =  "i2c1_0";
+			groups = "i2c1_0";
 		};
 	};
 
 	i2c2_pins: i2c2-pins {
 		mux {
 			function = "i2c";
-			groups =  "i2c2_0";
+			groups = "i2c2_0";
 		};
 	};
 
@@ -366,14 +369,14 @@
 	irrx_pins: irrx-pins {
 		mux {
 			function = "ir";
-			groups =  "ir_1_rx";
+			groups = "ir_1_rx";
 		};
 	};
 
 	irtx_pins: irtx-pins {
 		mux {
 			function = "ir";
-			groups =  "ir_1_tx";
+			groups = "ir_1_tx";
 		};
 	};
 
diff --git a/arch/arm64/boot/dts/mediatek/mt7622-rfb1.dts b/arch/arm64/boot/dts/mediatek/mt7622-rfb1.dts
index 596c073d8b05..36722cabe626 100644
--- a/arch/arm64/boot/dts/mediatek/mt7622-rfb1.dts
+++ b/arch/arm64/boot/dts/mediatek/mt7622-rfb1.dts
@@ -40,15 +40,14 @@
 
 	gpio-keys {
 		compatible = "gpio-keys";
-		poll-interval = <100>;
 
-		factory {
+		key-factory {
 			label = "factory";
 			linux,code = <BTN_0>;
 			gpios = <&pio 0 0>;
 		};
 
-		wps {
+		key-wps {
 			label = "wps";
 			linux,code = <KEY_WPS_BUTTON>;
 			gpios = <&pio 102 0>;
@@ -298,14 +297,14 @@
 	i2c1_pins: i2c1-pins {
 		mux {
 			function = "i2c";
-			groups =  "i2c1_0";
+			groups = "i2c1_0";
 		};
 	};
 
 	i2c2_pins: i2c2-pins {
 		mux {
 			function = "i2c";
-			groups =  "i2c2_0";
+			groups = "i2c2_0";
 		};
 	};
 
@@ -328,14 +327,14 @@
 	irrx_pins: irrx-pins {
 		mux {
 			function = "ir";
-			groups =  "ir_1_rx";
+			groups = "ir_1_rx";
 		};
 	};
 
 	irtx_pins: irtx-pins {
 		mux {
 			function = "ir";
-			groups =  "ir_1_tx";
+			groups = "ir_1_tx";
 		};
 	};
 
diff --git a/arch/arm64/boot/dts/mediatek/mt7622.dtsi b/arch/arm64/boot/dts/mediatek/mt7622.dtsi
index 6f8cb3ad1e84..146e18b5b1f4 100644
--- a/arch/arm64/boot/dts/mediatek/mt7622.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt7622.dtsi
@@ -80,6 +80,7 @@
 			enable-method = "psci";
 			clock-frequency = <1300000000>;
 			cci-control-port = <&cci_control2>;
+			next-level-cache = <&L2>;
 		};
 
 		cpu1: cpu@1 {
@@ -94,6 +95,12 @@
 			enable-method = "psci";
 			clock-frequency = <1300000000>;
 			cci-control-port = <&cci_control2>;
+			next-level-cache = <&L2>;
+		};
+
+		L2: l2-cache {
+			compatible = "cache";
+			cache-level = <2>;
 		};
 	};
 
@@ -111,8 +118,8 @@
 	};
 
 	psci {
-		compatible  = "arm,psci-0.2";
-		method      = "smc";
+		compatible = "arm,psci-0.2";
+		method = "smc";
 	};
 
 	pmu {
@@ -357,7 +364,7 @@
 		};
 
 		cci_control2: slave-if@5000 {
-			compatible = "arm,cci-400-ctrl-if";
+			compatible = "arm,cci-400-ctrl-if", "syscon";
 			interface-type = "ace";
 			reg = <0x5000 0x1000>;
 		};
@@ -545,6 +552,18 @@
 		status = "disabled";
 	};
 
+	snfi: spi@1100d000 {
+		compatible = "mediatek,mt7622-snand";
+		reg = <0 0x1100d000 0 0x1000>;
+		interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_LOW>;
+		clocks = <&pericfg CLK_PERI_NFI_PD>, <&pericfg CLK_PERI_SNFI_PD>;
+		clock-names = "nfi_clk", "pad_clk";
+		nand-ecc-engine = <&bch>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "disabled";
+	};
+
 	bch: ecc@1100e000 {
 		compatible = "mediatek,mt7622-ecc";
 		reg = <0 0x1100e000 0 0x1000>;
@@ -597,9 +616,9 @@
 
 		afe: audio-controller {
 			compatible = "mediatek,mt7622-audio";
-			interrupts =  <GIC_SPI 144 IRQ_TYPE_LEVEL_LOW>,
-				      <GIC_SPI 145 IRQ_TYPE_LEVEL_LOW>;
-			interrupt-names	= "afe", "asys";
+			interrupts = <GIC_SPI 144 IRQ_TYPE_LEVEL_LOW>,
+				     <GIC_SPI 145 IRQ_TYPE_LEVEL_LOW>;
+			interrupt-names = "afe", "asys";
 
 			clocks = <&infracfg CLK_INFRA_AUDIO_PD>,
 				 <&topckgen CLK_TOP_AUD1_SEL>,
@@ -901,6 +920,11 @@
 		};
 	};
 
+	hifsys: syscon@1af00000 {
+		compatible = "mediatek,mt7622-hifsys", "syscon";
+		reg = <0 0x1af00000 0 0x70>;
+	};
+
 	ethsys: syscon@1b000000 {
 		compatible = "mediatek,mt7622-ethsys",
 			     "syscon";
@@ -917,6 +941,27 @@
 		clock-names = "hsdma";
 		power-domains = <&scpsys MT7622_POWER_DOMAIN_ETHSYS>;
 		#dma-cells = <1>;
+		dma-requests = <3>;
+	};
+
+	pcie_mirror: pcie-mirror@10000400 {
+		compatible = "mediatek,mt7622-pcie-mirror",
+			     "syscon";
+		reg = <0 0x10000400 0 0x10>;
+	};
+
+	wed0: wed@1020a000 {
+		compatible = "mediatek,mt7622-wed",
+			     "syscon";
+		reg = <0 0x1020a000 0 0x1000>;
+		interrupts = <GIC_SPI 214 IRQ_TYPE_LEVEL_LOW>;
+	};
+
+	wed1: wed@1020b000 {
+		compatible = "mediatek,mt7622-wed",
+			     "syscon";
+		reg = <0 0x1020b000 0 0x1000>;
+		interrupts = <GIC_SPI 215 IRQ_TYPE_LEVEL_LOW>;
 	};
 
 	eth: ethernet@1b100000 {
@@ -945,6 +990,11 @@
 		power-domains = <&scpsys MT7622_POWER_DOMAIN_ETHSYS>;
 		mediatek,ethsys = <&ethsys>;
 		mediatek,sgmiisys = <&sgmiisys>;
+		cci-control-port = <&cci_control2>;
+		mediatek,wed = <&wed0>, <&wed1>;
+		mediatek,pcie-mirror = <&pcie_mirror>;
+		mediatek,hifsys = <&hifsys>;
+		dma-coherent;
 		#address-cells = <1>;
 		#size-cells = <0>;
 		status = "disabled";
diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts b/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
new file mode 100644
index 000000000000..afe37b702eef
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt7986a-rfb.dts
@@ -0,0 +1,170 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright (C) 2021 MediaTek Inc.
+ * Author: Sam.Shih <sam.shih@mediatek.com>
+ */
+
+/dts-v1/;
+#include "mt7986a.dtsi"
+
+/ {
+	model = "MediaTek MT7986a RFB";
+	compatible = "mediatek,mt7986a-rfb";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@40000000 {
+		device_type = "memory";
+		reg = <0 0x40000000 0 0x40000000>;
+	};
+};
+
+&eth {
+	status = "okay";
+
+	gmac0: mac@0 {
+		compatible = "mediatek,eth-mac";
+		reg = <0>;
+		phy-mode = "2500base-x";
+
+		fixed-link {
+			speed = <2500>;
+			full-duplex;
+			pause;
+		};
+	};
+
+	mdio: mdio-bus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+};
+
+&mdio {
+	switch: switch@0 {
+		compatible = "mediatek,mt7531";
+		reg = <31>;
+		reset-gpios = <&pio 5 0>;
+	};
+};
+
+&switch {
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+			label = "lan0";
+		};
+
+		port@1 {
+			reg = <1>;
+			label = "lan1";
+		};
+
+		port@2 {
+			reg = <2>;
+			label = "lan2";
+		};
+
+		port@3 {
+			reg = <3>;
+			label = "lan3";
+		};
+
+		port@4 {
+			reg = <4>;
+			label = "lan4";
+		};
+
+		port@6 {
+			reg = <6>;
+			label = "cpu";
+			ethernet = <&gmac0>;
+			phy-mode = "2500base-x";
+
+			fixed-link {
+				speed = <2500>;
+				full-duplex;
+				pause;
+			};
+		};
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart2_pins>;
+	status = "okay";
+};
+
+&wifi {
+	status = "okay";
+	pinctrl-names = "default", "dbdc";
+	pinctrl-0 = <&wf_2g_5g_pins>;
+	pinctrl-1 = <&wf_dbdc_pins>;
+};
+
+&pio {
+	uart1_pins: uart1-pins {
+		mux {
+			function = "uart";
+			groups = "uart1";
+		};
+	};
+
+	uart2_pins: uart2-pins {
+		mux {
+			function = "uart";
+			groups = "uart2";
+		};
+	};
+
+	wf_2g_5g_pins: wf-2g-5g-pins {
+		mux {
+			function = "wifi";
+			groups = "wf_2g", "wf_5g";
+		};
+		conf {
+			pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4",
+			       "WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6",
+			       "WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10",
+			       "WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1",
+			       "WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0",
+			       "WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8",
+			       "WF1_TOP_CLK", "WF1_TOP_DATA";
+			drive-strength = <4>;
+		};
+	};
+
+	wf_dbdc_pins: wf-dbdc-pins {
+		mux {
+			function = "wifi";
+			groups = "wf_dbdc";
+		};
+		conf {
+			pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4",
+			       "WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6",
+			       "WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10",
+			       "WF0_TOP_CLK", "WF0_TOP_DATA";
+			drive-strength = <4>;
+		};
+	};
+};
diff --git a/arch/arm64/boot/dts/mediatek/mt7986a.dtsi b/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
new file mode 100644
index 000000000000..72e0d9722e07
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt7986a.dtsi
@@ -0,0 +1,313 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright (C) 2021 MediaTek Inc.
+ * Author: Sam.Shih <sam.shih@mediatek.com>
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/mt7986-clk.h>
+#include <dt-bindings/reset/mt7986-resets.h>
+
+/ {
+	interrupt-parent = <&gic>;
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	clk40m: oscillator@0 {
+		compatible = "fixed-clock";
+		clock-frequency = <40000000>;
+		#clock-cells = <0>;
+		clock-output-names = "clkxtal";
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			enable-method = "psci";
+			reg = <0x0>;
+			#cooling-cells = <2>;
+		};
+
+		cpu1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			enable-method = "psci";
+			reg = <0x1>;
+			#cooling-cells = <2>;
+		};
+
+		cpu2: cpu@2 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			enable-method = "psci";
+			reg = <0x2>;
+			#cooling-cells = <2>;
+		};
+
+		cpu3: cpu@3 {
+			device_type = "cpu";
+			enable-method = "psci";
+			compatible = "arm,cortex-a53";
+			reg = <0x3>;
+			#cooling-cells = <2>;
+		};
+	};
+
+	psci {
+		compatible = "arm,psci-0.2";
+		method = "smc";
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+		/* 192 KiB reserved for ARM Trusted Firmware (BL31) */
+		secmon_reserved: secmon@43000000 {
+			reg = <0 0x43000000 0 0x30000>;
+			no-map;
+		};
+
+		wmcpu_emi: wmcpu-reserved@4fc00000 {
+			no-map;
+			reg = <0 0x4fc00000 0 0x00100000>;
+		};
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupt-parent = <&gic>;
+		interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW>,
+			     <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW>,
+			     <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW>,
+			     <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW>;
+	};
+
+	soc {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		compatible = "simple-bus";
+		ranges;
+
+		gic: interrupt-controller@c000000 {
+			compatible = "arm,gic-v3";
+			#interrupt-cells = <3>;
+			interrupt-parent = <&gic>;
+			interrupt-controller;
+			reg = <0 0x0c000000 0 0x10000>,  /* GICD */
+			      <0 0x0c080000 0 0x80000>,  /* GICR */
+			      <0 0x0c400000 0 0x2000>,   /* GICC */
+			      <0 0x0c410000 0 0x1000>,   /* GICH */
+			      <0 0x0c420000 0 0x2000>;   /* GICV */
+			interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		infracfg: infracfg@10001000 {
+			compatible = "mediatek,mt7986-infracfg", "syscon";
+			reg = <0 0x10001000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
+		topckgen: topckgen@1001b000 {
+			compatible = "mediatek,mt7986-topckgen", "syscon";
+			reg = <0 0x1001B000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
+		watchdog: watchdog@1001c000 {
+			compatible = "mediatek,mt7986-wdt",
+				     "mediatek,mt6589-wdt";
+			reg = <0 0x1001c000 0 0x1000>;
+			interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
+			#reset-cells = <1>;
+			status = "disabled";
+		};
+
+		apmixedsys: apmixedsys@1001e000 {
+			compatible = "mediatek,mt7986-apmixedsys";
+			reg = <0 0x1001E000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
+		pio: pinctrl@1001f000 {
+			compatible = "mediatek,mt7986a-pinctrl";
+			reg = <0 0x1001f000 0 0x1000>,
+			      <0 0x11c30000 0 0x1000>,
+			      <0 0x11c40000 0 0x1000>,
+			      <0 0x11e20000 0 0x1000>,
+			      <0 0x11e30000 0 0x1000>,
+			      <0 0x11f00000 0 0x1000>,
+			      <0 0x11f10000 0 0x1000>,
+			      <0 0x1000b000 0 0x1000>;
+			reg-names = "gpio", "iocfg_rt", "iocfg_rb", "iocfg_lt",
+				    "iocfg_lb", "iocfg_tr", "iocfg_tl", "eint";
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&pio 0 0 100>;
+			interrupt-controller;
+			interrupts = <GIC_SPI 225 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-parent = <&gic>;
+			#interrupt-cells = <2>;
+		};
+
+		sgmiisys0: syscon@10060000 {
+			compatible = "mediatek,mt7986-sgmiisys_0",
+				     "syscon";
+			reg = <0 0x10060000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
+		sgmiisys1: syscon@10070000 {
+			compatible = "mediatek,mt7986-sgmiisys_1",
+				     "syscon";
+			reg = <0 0x10070000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
+		trng: trng@1020f000 {
+			compatible = "mediatek,mt7986-rng",
+				     "mediatek,mt7623-rng";
+			reg = <0 0x1020f000 0 0x100>;
+			clocks = <&infracfg CLK_INFRA_TRNG_CK>;
+			clock-names = "rng";
+			status = "disabled";
+		};
+
+		uart0: serial@11002000 {
+			compatible = "mediatek,mt7986-uart",
+				     "mediatek,mt6577-uart";
+			reg = <0 0x11002000 0 0x400>;
+			interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&infracfg CLK_INFRA_UART0_SEL>,
+				 <&infracfg CLK_INFRA_UART0_CK>;
+			clock-names = "baud", "bus";
+			assigned-clocks = <&topckgen CLK_TOP_UART_SEL>,
+					  <&infracfg CLK_INFRA_UART0_SEL>;
+			assigned-clock-parents = <&topckgen CLK_TOP_XTAL>,
+						 <&topckgen CLK_TOP_UART_SEL>;
+			status = "disabled";
+		};
+
+		uart1: serial@11003000 {
+			compatible = "mediatek,mt7986-uart",
+				     "mediatek,mt6577-uart";
+			reg = <0 0x11003000 0 0x400>;
+			interrupts = <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&infracfg CLK_INFRA_UART1_SEL>,
+				 <&infracfg CLK_INFRA_UART1_CK>;
+			clock-names = "baud", "bus";
+			assigned-clocks = <&infracfg CLK_INFRA_UART1_SEL>;
+			assigned-clock-parents = <&topckgen CLK_TOP_F26M_SEL>;
+			status = "disabled";
+		};
+
+		uart2: serial@11004000 {
+			compatible = "mediatek,mt7986-uart",
+				     "mediatek,mt6577-uart";
+			reg = <0 0x11004000 0 0x400>;
+			interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&infracfg CLK_INFRA_UART2_SEL>,
+				 <&infracfg CLK_INFRA_UART2_CK>;
+			clock-names = "baud", "bus";
+			assigned-clocks = <&infracfg CLK_INFRA_UART2_SEL>;
+			assigned-clock-parents = <&topckgen CLK_TOP_F26M_SEL>;
+			status = "disabled";
+		};
+
+		ethsys: syscon@15000000 {
+			 #address-cells = <1>;
+			 #size-cells = <1>;
+			 compatible = "mediatek,mt7986-ethsys",
+				      "syscon";
+			 reg = <0 0x15000000 0 0x1000>;
+			 #clock-cells = <1>;
+			 #reset-cells = <1>;
+		};
+
+		wed_pcie: wed-pcie@10003000 {
+			compatible = "mediatek,mt7986-wed-pcie",
+				     "syscon";
+			reg = <0 0x10003000 0 0x10>;
+		};
+
+		wed0: wed@15010000 {
+			compatible = "mediatek,mt7986-wed",
+				     "syscon";
+			reg = <0 0x15010000 0 0x1000>;
+			interrupt-parent = <&gic>;
+			interrupts = <GIC_SPI 205 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		wed1: wed@15011000 {
+			compatible = "mediatek,mt7986-wed",
+				     "syscon";
+			reg = <0 0x15011000 0 0x1000>;
+			interrupt-parent = <&gic>;
+			interrupts = <GIC_SPI 206 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		eth: ethernet@15100000 {
+			compatible = "mediatek,mt7986-eth";
+			reg = <0 0x15100000 0 0x80000>;
+			interrupts = <GIC_SPI 196 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 197 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 198 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 199 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ethsys CLK_ETH_FE_EN>,
+				 <&ethsys CLK_ETH_GP2_EN>,
+				 <&ethsys CLK_ETH_GP1_EN>,
+				 <&ethsys CLK_ETH_WOCPU1_EN>,
+				 <&ethsys CLK_ETH_WOCPU0_EN>,
+				 <&sgmiisys0 CLK_SGMII0_TX250M_EN>,
+				 <&sgmiisys0 CLK_SGMII0_RX250M_EN>,
+				 <&sgmiisys0 CLK_SGMII0_CDR_REF>,
+				 <&sgmiisys0 CLK_SGMII0_CDR_FB>,
+				 <&sgmiisys1 CLK_SGMII1_TX250M_EN>,
+				 <&sgmiisys1 CLK_SGMII1_RX250M_EN>,
+				 <&sgmiisys1 CLK_SGMII1_CDR_REF>,
+				 <&sgmiisys1 CLK_SGMII1_CDR_FB>,
+				 <&topckgen CLK_TOP_NETSYS_SEL>,
+				 <&topckgen CLK_TOP_NETSYS_500M_SEL>;
+			clock-names = "fe", "gp2", "gp1", "wocpu1", "wocpu0",
+				      "sgmii_tx250m", "sgmii_rx250m",
+				      "sgmii_cdr_ref", "sgmii_cdr_fb",
+				      "sgmii2_tx250m", "sgmii2_rx250m",
+				      "sgmii2_cdr_ref", "sgmii2_cdr_fb",
+				      "netsys0", "netsys1";
+			assigned-clocks = <&topckgen CLK_TOP_NETSYS_2X_SEL>,
+					  <&topckgen CLK_TOP_SGM_325M_SEL>;
+			assigned-clock-parents = <&apmixedsys CLK_APMIXED_NET2PLL>,
+						 <&apmixedsys CLK_APMIXED_SGMPLL>;
+			mediatek,ethsys = <&ethsys>;
+			mediatek,sgmiisys = <&sgmiisys0>, <&sgmiisys1>;
+			mediatek,wed-pcie = <&wed_pcie>;
+			mediatek,wed = <&wed0>, <&wed1>;
+			#reset-cells = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		wifi: wifi@18000000 {
+			compatible = "mediatek,mt7986-wmac";
+			resets = <&watchdog MT7986_TOPRGU_CONSYS_SW_RST>;
+			reset-names = "consys";
+			clocks = <&topckgen CLK_TOP_CONN_MCUSYS_SEL>,
+				 <&topckgen CLK_TOP_AP2CNN_HOST_SEL>;
+			clock-names = "mcu", "ap2conn";
+			reg = <0 0x18000000 0 0x1000000>,
+			      <0 0x10003000 0 0x1000>,
+			      <0 0x11d10000 0 0x1000>;
+			interrupts = <GIC_SPI 213 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 214 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 215 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 216 IRQ_TYPE_LEVEL_HIGH>;
+			memory-region = <&wmcpu_emi>;
+		};
+	};
+
+};
diff --git a/arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts b/arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts
new file mode 100644
index 000000000000..3443013b5971
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt7986b-rfb.dts
@@ -0,0 +1,140 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright (C) 2021 MediaTek Inc.
+ * Author: Sam.Shih <sam.shih@mediatek.com>
+ */
+
+/dts-v1/;
+#include "mt7986b.dtsi"
+
+/ {
+	model = "MediaTek MT7986b RFB";
+	compatible = "mediatek,mt7986b-rfb";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@40000000 {
+		device_type = "memory";
+		reg = <0 0x40000000 0 0x40000000>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&eth {
+	status = "okay";
+
+	gmac0: mac@0 {
+		compatible = "mediatek,eth-mac";
+		reg = <0>;
+		phy-mode = "2500base-x";
+
+		fixed-link {
+			speed = <2500>;
+			full-duplex;
+			pause;
+		};
+	};
+
+	mdio: mdio-bus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		switch@0 {
+			compatible = "mediatek,mt7531";
+			reg = <31>;
+			reset-gpios = <&pio 5 0>;
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+					label = "lan0";
+				};
+
+				port@1 {
+					reg = <1>;
+					label = "lan1";
+				};
+
+				port@2 {
+					reg = <2>;
+					label = "lan2";
+				};
+
+				port@3 {
+					reg = <3>;
+					label = "lan3";
+				};
+
+				port@4 {
+					reg = <4>;
+					label = "lan4";
+				};
+
+				port@6 {
+					reg = <6>;
+					label = "cpu";
+					ethernet = <&gmac0>;
+					phy-mode = "2500base-x";
+
+					fixed-link {
+						speed = <2500>;
+						full-duplex;
+						pause;
+					};
+				};
+			};
+		};
+	};
+};
+
+&wifi {
+	status = "okay";
+	pinctrl-names = "default", "dbdc";
+	pinctrl-0 = <&wf_2g_5g_pins>;
+	pinctrl-1 = <&wf_dbdc_pins>;
+};
+
+&pio {
+	wf_2g_5g_pins: wf-2g-5g-pins {
+		mux {
+			function = "wifi";
+			groups = "wf_2g", "wf_5g";
+		};
+		conf {
+			pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4",
+			       "WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6",
+			       "WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10",
+			       "WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1",
+			       "WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0",
+			       "WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8",
+			       "WF1_TOP_CLK", "WF1_TOP_DATA";
+			drive-strength = <4>;
+		};
+	};
+
+	wf_dbdc_pins: wf-dbdc-pins {
+		mux {
+			function = "wifi";
+			groups = "wf_dbdc";
+		};
+		conf {
+			pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4",
+			       "WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6",
+			       "WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10",
+			       "WF0_TOP_CLK", "WF0_TOP_DATA";
+			drive-strength = <4>;
+		};
+	};
+};
diff --git a/arch/arm64/boot/dts/mediatek/mt7986b.dtsi b/arch/arm64/boot/dts/mediatek/mt7986b.dtsi
new file mode 100644
index 000000000000..23923b9f8944
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt7986b.dtsi
@@ -0,0 +1,12 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright (C) 2021 MediaTek Inc.
+ * Author: Sam.Shih <sam.shih@mediatek.com>
+ */
+
+#include "mt7986a.dtsi"
+
+&pio {
+	compatible = "mediatek,mt7986b-pinctrl";
+	gpio-ranges = <&pio 0 0 41>, <&pio 66 66 35>;
+};
diff --git a/arch/arm64/boot/dts/mediatek/mt8167.dtsi b/arch/arm64/boot/dts/mediatek/mt8167.dtsi
index 9029051624a6..fbe1a1128cc6 100644
--- a/arch/arm64/boot/dts/mediatek/mt8167.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt8167.dtsi
@@ -36,9 +36,8 @@
 		};
 
 		scpsys: syscon@10006000 {
-			compatible = "syscon", "simple-mfd";
+			compatible = "mediatek,mt8167-scpsys", "syscon", "simple-mfd";
 			reg = <0 0x10006000 0 0x1000>;
-			#power-domain-cells = <1>;
 
 			spm: power-controller {
 				compatible = "mediatek,mt8167-power-controller";
@@ -174,7 +173,7 @@
 		iommu: m4u@10203000 {
 			compatible = "mediatek,mt8167-m4u";
 			reg = <0 0x10203000 0 0x1000>;
-			mediatek,larbs = <&larb0 &larb1 &larb2>;
+			mediatek,larbs = <&larb0>, <&larb1>, <&larb2>;
 			interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_LOW>;
 			#iommu-cells = <1>;
 		};
diff --git a/arch/arm64/boot/dts/mediatek/mt8173-elm-hana-rev7.dts b/arch/arm64/boot/dts/mediatek/mt8173-elm-hana-rev7.dts
index 44f6149c1307..28433b94f7c7 100644
--- a/arch/arm64/boot/dts/mediatek/mt8173-elm-hana-rev7.dts
+++ b/arch/arm64/boot/dts/mediatek/mt8173-elm-hana-rev7.dts
@@ -21,7 +21,7 @@
 };
 
 &gpio_keys {
-	/delete-node/tablet_mode;
-	/delete-node/volume_down;
-	/delete-node/volume_up;
+	/delete-node/switch-tablet-mode;
+	/delete-node/switch-volume-down;
+	/delete-node/switch-volume-up;
 };
diff --git a/arch/arm64/boot/dts/mediatek/mt8173-elm.dtsi b/arch/arm64/boot/dts/mediatek/mt8173-elm.dtsi
index e666ebb28980..e21feb85d822 100644
--- a/arch/arm64/boot/dts/mediatek/mt8173-elm.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt8173-elm.dtsi
@@ -28,7 +28,7 @@
 		enable-gpios = <&pio 95 GPIO_ACTIVE_HIGH>;
 
 		pinctrl-names = "default";
-		pinctrl-0 = <&disp_pwm0_pins>;
+		pinctrl-0 = <&panel_backlight_en_pins>;
 		status = "okay";
 	};
 
@@ -53,7 +53,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&gpio_keys_pins>;
 
-		lid {
+		switch-lid {
 			label = "Lid";
 			gpios = <&pio 69 GPIO_ACTIVE_LOW>;
 			linux,code = <SW_LID>;
@@ -61,7 +61,7 @@
 			gpio-key,wakeup;
 		};
 
-		power {
+		switch-power {
 			label = "Power";
 			gpios = <&pio 14 GPIO_ACTIVE_HIGH>;
 			linux,code = <KEY_POWER>;
@@ -69,7 +69,7 @@
 			gpio-key,wakeup;
 		};
 
-		tablet_mode {
+		switch-tablet-mode {
 			label = "Tablet_mode";
 			gpios = <&pio 121 GPIO_ACTIVE_HIGH>;
 			linux,code = <SW_TABLET_MODE>;
@@ -77,13 +77,13 @@
 			gpio-key,wakeup;
 		};
 
-		volume_down {
+		switch-volume-down {
 			label = "Volume_down";
 			gpios = <&pio 123 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_VOLUMEDOWN>;
 		};
 
-		volume_up {
+		switch-volume-up {
 			label = "Volume_up";
 			gpios = <&pio 124 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_VOLUMEUP>;
@@ -300,8 +300,8 @@
 				regulator-name = "VBUCKA";
 				regulator-min-microvolt = < 700000>;
 				regulator-max-microvolt = <1310000>;
-				regulator-min-microamp  = <2000000>;
-				regulator-max-microamp  = <4400000>;
+				regulator-min-microamp = <2000000>;
+				regulator-max-microamp = <4400000>;
 				regulator-ramp-delay = <10000>;
 				regulator-always-on;
 				regulator-allowed-modes = <DA9211_BUCK_MODE_SYNC
@@ -312,8 +312,8 @@
 				regulator-name = "VBUCKB";
 				regulator-min-microvolt = < 700000>;
 				regulator-max-microvolt = <1310000>;
-				regulator-min-microamp  = <2000000>;
-				regulator-max-microamp  = <3000000>;
+				regulator-min-microamp = <2000000>;
+				regulator-max-microamp = <3000000>;
 				regulator-ramp-delay = <10000>;
 			};
 		};
@@ -374,8 +374,8 @@
 	mmc-hs400-1_8v;
 	cap-mmc-hw-reset;
 	hs400-ds-delay = <0x14015>;
-	mediatek,hs200-cmd-int-delay=<30>;
-	mediatek,hs400-cmd-int-delay=<14>;
+	mediatek,hs200-cmd-int-delay = <30>;
+	mediatek,hs400-cmd-int-delay = <14>;
 	mediatek,hs400-cmd-resp-sel-rising;
 	vmmc-supply = <&mt6397_vemc_3v3_reg>;
 	vqmmc-supply = <&mt6397_vio18_reg>;
@@ -410,7 +410,7 @@
 	sd-uhs-sdr50;
 	sd-uhs-sdr104;
 	keep-power-in-suspend;
-	enable-sdio-wakeup;
+	wakeup-source;
 	cap-sdio-irq;
 	vmmc-supply = <&sdio_fixed_3v3>;
 	vqmmc-supply = <&mt6397_vgp3_reg>;
@@ -827,6 +827,12 @@
 		};
 	};
 
+	panel_backlight_en_pins: panel_backlight_en_pins {
+		pins1 {
+			pinmux = <MT8173_PIN_95_PCM_TX__FUNC_GPIO95>;
+		};
+	};
+
 	panel_fixed_pins: panel_fixed_pins {
 		pins1 {
 			pinmux = <MT8173_PIN_41_CMMCLK__FUNC_GPIO41>;
@@ -901,6 +907,8 @@
 };
 
 &pwm0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&disp_pwm0_pins>;
 	status = "okay";
 };
 
diff --git a/arch/arm64/boot/dts/mediatek/mt8173-evb.dts b/arch/arm64/boot/dts/mediatek/mt8173-evb.dts
index 4fa1e93302c7..0b5f154007be 100644
--- a/arch/arm64/boot/dts/mediatek/mt8173-evb.dts
+++ b/arch/arm64/boot/dts/mediatek/mt8173-evb.dts
@@ -122,8 +122,8 @@
 				regulator-name = "VBUCKA";
 				regulator-min-microvolt = < 700000>;
 				regulator-max-microvolt = <1310000>;
-				regulator-min-microamp	= <2000000>;
-				regulator-max-microamp	= <4400000>;
+				regulator-min-microamp = <2000000>;
+				regulator-max-microamp = <4400000>;
 				regulator-ramp-delay = <10000>;
 				regulator-always-on;
 			};
@@ -132,8 +132,8 @@
 				regulator-name = "VBUCKB";
 				regulator-min-microvolt = < 700000>;
 				regulator-max-microvolt = <1310000>;
-				regulator-min-microamp	= <2000000>;
-				regulator-max-microamp	= <3000000>;
+				regulator-min-microamp = <2000000>;
+				regulator-max-microamp = <3000000>;
 				regulator-ramp-delay = <10000>;
 			};
 		};
@@ -148,8 +148,8 @@
 	bus-width = <8>;
 	max-frequency = <50000000>;
 	cap-mmc-highspeed;
-	mediatek,hs200-cmd-int-delay=<26>;
-	mediatek,hs400-cmd-int-delay=<14>;
+	mediatek,hs200-cmd-int-delay = <26>;
+	mediatek,hs400-cmd-int-delay = <14>;
 	mediatek,hs400-cmd-resp-sel-rising;
 	vmmc-supply = <&mt6397_vemc_3v3_reg>;
 	vqmmc-supply = <&mt6397_vio18_reg>;
diff --git a/arch/arm64/boot/dts/mediatek/mt8173.dtsi b/arch/arm64/boot/dts/mediatek/mt8173.dtsi
index dee66e5f054c..7640b5158ff9 100644
--- a/arch/arm64/boot/dts/mediatek/mt8173.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt8173.dtsi
@@ -1,14 +1,7 @@
+// SPDX-License-Identifier: GPL-2.0-only
 /*
  * Copyright (c) 2014 MediaTek Inc.
  * Author: Eddie Huang <eddie.huang@mediatek.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- * This program is distributed in the hope that it will be useful,
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
  */
 
 #include <dt-bindings/clock/mt8173-clk.h>
@@ -57,7 +50,7 @@
 		serial3 = &uart3;
 	};
 
-	cluster0_opp: opp_table0 {
+	cluster0_opp: opp-table-0 {
 		compatible = "operating-points-v2";
 		opp-shared;
 		opp-507000000 {
@@ -94,7 +87,7 @@
 		};
 	};
 
-	cluster1_opp: opp_table1 {
+	cluster1_opp: opp-table-1 {
 		compatible = "operating-points-v2";
 		opp-shared;
 		opp-507000000 {
@@ -246,9 +239,9 @@
 	psci {
 		compatible = "arm,psci-1.0", "arm,psci-0.2", "arm,psci";
 		method = "smc";
-		cpu_suspend   = <0x84000001>;
-		cpu_off	      = <0x84000002>;
-		cpu_on	      = <0x84000003>;
+		cpu_suspend = <0x84000001>;
+		cpu_off	 = <0x84000002>;
+		cpu_on	 = <0x84000003>;
 	};
 
 	clk26m: oscillator0 {
@@ -273,7 +266,7 @@
 	};
 
 	thermal-zones {
-		cpu_thermal: cpu_thermal {
+		cpu_thermal: cpu-thermal {
 			polling-delay-passive = <1000>; /* milliseconds */
 			polling-delay = <1000>; /* milliseconds */
 
@@ -451,9 +444,8 @@
 		};
 
 		scpsys: syscon@10006000 {
-			compatible = "syscon", "simple-mfd";
+			compatible = "mediatek,mt8173-scpsys", "syscon", "simple-mfd";
 			reg = <0 0x10006000 0 0x1000>;
-			#power-domain-cells = <1>;
 
 			/* System Power Manager */
 			spm: power-controller {
@@ -588,8 +580,9 @@
 			interrupts = <GIC_SPI 139 IRQ_TYPE_LEVEL_LOW>;
 			clocks = <&infracfg CLK_INFRA_M4U>;
 			clock-names = "bclk";
-			mediatek,larbs = <&larb0 &larb1 &larb2
-					  &larb3 &larb4 &larb5>;
+			mediatek,infracfg = <&infracfg>;
+			mediatek,larbs = <&larb0>, <&larb1>, <&larb2>,
+					 <&larb3>, <&larb4>, <&larb5>;
 			#iommu-cells = <1>;
 		};
 
@@ -790,9 +783,12 @@
 		nor_flash: spi@1100d000 {
 			compatible = "mediatek,mt8173-nor";
 			reg = <0 0x1100d000 0 0xe0>;
+			assigned-clocks = <&topckgen CLK_TOP_SPI_SEL>;
+			assigned-clock-parents = <&clk26m>;
 			clocks = <&pericfg CLK_PERI_SPI>,
-				 <&topckgen CLK_TOP_SPINFI_IFR_SEL>;
-			clock-names = "spi", "sf";
+				 <&topckgen CLK_TOP_SPINFI_IFR_SEL>,
+				 <&pericfg CLK_PERI_NFI>;
+			clock-names = "spi", "sf", "axi";
 			#address-cells = <1>;
 			#size-cells = <0>;
 			status = "disabled";
@@ -1010,7 +1006,6 @@
 				 <&mmsys CLK_MM_MUTEX_32K>;
 			power-domains = <&spm MT8173_POWER_DOMAIN_MM>;
 			iommus = <&iommu M4U_PORT_MDP_RDMA0>;
-			mediatek,larb = <&larb0>;
 			mediatek,vpu = <&vpu>;
 		};
 
@@ -1021,7 +1016,6 @@
 				 <&mmsys CLK_MM_MUTEX_32K>;
 			power-domains = <&spm MT8173_POWER_DOMAIN_MM>;
 			iommus = <&iommu M4U_PORT_MDP_RDMA1>;
-			mediatek,larb = <&larb4>;
 		};
 
 		mdp_rsz0: rsz@14003000 {
@@ -1051,7 +1045,6 @@
 			clocks = <&mmsys CLK_MM_MDP_WDMA>;
 			power-domains = <&spm MT8173_POWER_DOMAIN_MM>;
 			iommus = <&iommu M4U_PORT_MDP_WDMA>;
-			mediatek,larb = <&larb0>;
 		};
 
 		mdp_wrot0: wrot@14007000 {
@@ -1060,7 +1053,6 @@
 			clocks = <&mmsys CLK_MM_MDP_WROT0>;
 			power-domains = <&spm MT8173_POWER_DOMAIN_MM>;
 			iommus = <&iommu M4U_PORT_MDP_WROT0>;
-			mediatek,larb = <&larb0>;
 		};
 
 		mdp_wrot1: wrot@14008000 {
@@ -1069,7 +1061,6 @@
 			clocks = <&mmsys CLK_MM_MDP_WROT1>;
 			power-domains = <&spm MT8173_POWER_DOMAIN_MM>;
 			iommus = <&iommu M4U_PORT_MDP_WROT1>;
-			mediatek,larb = <&larb4>;
 		};
 
 		ovl0: ovl@1400c000 {
@@ -1079,7 +1070,6 @@
 			power-domains = <&spm MT8173_POWER_DOMAIN_MM>;
 			clocks = <&mmsys CLK_MM_DISP_OVL0>;
 			iommus = <&iommu M4U_PORT_DISP_OVL0>;
-			mediatek,larb = <&larb0>;
 			mediatek,gce-client-reg = <&gce SUBSYS_1400XXXX 0xc000 0x1000>;
 		};
 
@@ -1090,7 +1080,6 @@
 			power-domains = <&spm MT8173_POWER_DOMAIN_MM>;
 			clocks = <&mmsys CLK_MM_DISP_OVL1>;
 			iommus = <&iommu M4U_PORT_DISP_OVL1>;
-			mediatek,larb = <&larb4>;
 			mediatek,gce-client-reg = <&gce SUBSYS_1400XXXX 0xd000 0x1000>;
 		};
 
@@ -1101,7 +1090,6 @@
 			power-domains = <&spm MT8173_POWER_DOMAIN_MM>;
 			clocks = <&mmsys CLK_MM_DISP_RDMA0>;
 			iommus = <&iommu M4U_PORT_DISP_RDMA0>;
-			mediatek,larb = <&larb0>;
 			mediatek,gce-client-reg = <&gce SUBSYS_1400XXXX 0xe000 0x1000>;
 		};
 
@@ -1112,7 +1100,6 @@
 			power-domains = <&spm MT8173_POWER_DOMAIN_MM>;
 			clocks = <&mmsys CLK_MM_DISP_RDMA1>;
 			iommus = <&iommu M4U_PORT_DISP_RDMA1>;
-			mediatek,larb = <&larb4>;
 			mediatek,gce-client-reg = <&gce SUBSYS_1400XXXX 0xf000 0x1000>;
 		};
 
@@ -1123,7 +1110,6 @@
 			power-domains = <&spm MT8173_POWER_DOMAIN_MM>;
 			clocks = <&mmsys CLK_MM_DISP_RDMA2>;
 			iommus = <&iommu M4U_PORT_DISP_RDMA2>;
-			mediatek,larb = <&larb4>;
 			mediatek,gce-client-reg = <&gce SUBSYS_1401XXXX 0 0x1000>;
 		};
 
@@ -1134,7 +1120,6 @@
 			power-domains = <&spm MT8173_POWER_DOMAIN_MM>;
 			clocks = <&mmsys CLK_MM_DISP_WDMA0>;
 			iommus = <&iommu M4U_PORT_DISP_WDMA0>;
-			mediatek,larb = <&larb0>;
 			mediatek,gce-client-reg = <&gce SUBSYS_1401XXXX 0x1000 0x1000>;
 		};
 
@@ -1145,7 +1130,6 @@
 			power-domains = <&spm MT8173_POWER_DOMAIN_MM>;
 			clocks = <&mmsys CLK_MM_DISP_WDMA1>;
 			iommus = <&iommu M4U_PORT_DISP_WDMA1>;
-			mediatek,larb = <&larb4>;
 			mediatek,gce-client-reg = <&gce SUBSYS_1401XXXX 0x2000 0x1000>;
 		};
 
@@ -1212,6 +1196,7 @@
 			interrupts = <GIC_SPI 191 IRQ_TYPE_LEVEL_LOW>;
 			power-domains = <&spm MT8173_POWER_DOMAIN_MM>;
 			clocks = <&mmsys CLK_MM_DISP_UFOE>;
+			mediatek,gce-client-reg = <&gce SUBSYS_1401XXXX 0xa000 0x1000>;
 		};
 
 		dsi0: dsi@1401b000 {
@@ -1289,6 +1274,7 @@
 			interrupts = <GIC_SPI 169 IRQ_TYPE_LEVEL_LOW>;
 			power-domains = <&spm MT8173_POWER_DOMAIN_MM>;
 			clocks = <&mmsys CLK_MM_MUTEX_32K>;
+			mediatek,gce-client-reg = <&gce SUBSYS_1402XXXX 0 0x1000>;
 			mediatek,gce-events = <CMDQ_EVENT_MUTEX0_STREAM_EOF>,
                                               <CMDQ_EVENT_MUTEX1_STREAM_EOF>;
 		};
@@ -1316,6 +1302,7 @@
 			compatible = "mediatek,mt8173-disp-od";
 			reg = <0 0x14023000 0 0x1000>;
 			clocks = <&mmsys CLK_MM_DISP_OD>;
+			mediatek,gce-client-reg = <&gce SUBSYS_1402XXXX 0x3000 0x1000>;
 		};
 
 		hdmi0: hdmi@14025000 {
@@ -1397,7 +1384,6 @@
 			      <0 0x16027800 0 0x800>,	/* VDEC_HWB */
 			      <0 0x16028400 0 0x400>;	/* VDEC_HWG */
 			interrupts = <GIC_SPI 204 IRQ_TYPE_LEVEL_LOW>;
-			mediatek,larb = <&larb1>;
 			iommus = <&iommu M4U_PORT_HW_VDEC_MC_EXT>,
 				 <&iommu M4U_PORT_HW_VDEC_PP_EXT>,
 				 <&iommu M4U_PORT_HW_VDEC_AVC_MV_EXT>,
@@ -1465,7 +1451,6 @@
 			compatible = "mediatek,mt8173-vcodec-enc";
 			reg = <0 0x18002000 0 0x1000>;	/* VENC_SYS */
 			interrupts = <GIC_SPI 198 IRQ_TYPE_LEVEL_LOW>;
-			mediatek,larb = <&larb3>;
 			iommus = <&iommu M4U_PORT_VENC_RCPU>,
 				 <&iommu M4U_PORT_VENC_REC>,
 				 <&iommu M4U_PORT_VENC_BSDMA>,
@@ -1482,6 +1467,7 @@
 			clock-names = "venc_sel";
 			assigned-clocks = <&topckgen CLK_TOP_VENC_SEL>;
 			assigned-clock-parents = <&topckgen CLK_TOP_VCODECPLL>;
+			power-domains = <&spm MT8173_POWER_DOMAIN_VENC>;
 		};
 
 		jpegdec: jpegdec@18004000 {
@@ -1493,7 +1479,6 @@
 			clock-names = "jpgdec-smi",
 				      "jpgdec";
 			power-domains = <&spm MT8173_POWER_DOMAIN_VENC>;
-			mediatek,larb = <&larb3>;
 			iommus = <&iommu M4U_PORT_JPGDEC_WDMA>,
 				 <&iommu M4U_PORT_JPGDEC_BSDMA>;
 		};
@@ -1516,7 +1501,7 @@
 
 		vcodec_enc_vp8: vcodec@19002000 {
 			compatible = "mediatek,mt8173-vcodec-enc-vp8";
-			reg =  <0 0x19002000 0 0x1000>; /* VENC_LT_SYS */
+			reg = <0 0x19002000 0 0x1000>; /* VENC_LT_SYS */
 			interrupts = <GIC_SPI 202 IRQ_TYPE_LEVEL_LOW>;
 			iommus = <&iommu M4U_PORT_VENC_RCPU_SET2>,
 				 <&iommu M4U_PORT_VENC_REC_FRM_SET2>,
@@ -1527,13 +1512,13 @@
 				 <&iommu M4U_PORT_VENC_CUR_CHROMA_SET2>,
 				 <&iommu M4U_PORT_VENC_REF_LUMA_SET2>,
 				 <&iommu M4U_PORT_VENC_REC_CHROMA_SET2>;
-			mediatek,larb = <&larb5>;
 			mediatek,vpu = <&vpu>;
 			clocks = <&topckgen CLK_TOP_VENC_LT_SEL>;
 			clock-names = "venc_lt_sel";
 			assigned-clocks = <&topckgen CLK_TOP_VENC_LT_SEL>;
 			assigned-clock-parents =
 				 <&topckgen CLK_TOP_VCODECPLL_370P5>;
+			power-domains = <&spm MT8173_POWER_DOMAIN_VENC_LT>;
 		};
 	};
 };
diff --git a/arch/arm64/boot/dts/mediatek/mt8183-evb.dts b/arch/arm64/boot/dts/mediatek/mt8183-evb.dts
index 7bc0a6a7fadf..52dc4a50e34d 100644
--- a/arch/arm64/boot/dts/mediatek/mt8183-evb.dts
+++ b/arch/arm64/boot/dts/mediatek/mt8183-evb.dts
@@ -36,6 +36,14 @@
 			no-map;
 		};
 	};
+
+	ntc@0 {
+		compatible = "murata,ncp03wf104";
+		pullup-uv = <1800000>;
+		pullup-ohm = <390000>;
+		pulldown-ohm = <0>;
+		io-channels = <&auxadc 0>;
+	};
 };
 
 &auxadc {
@@ -126,7 +134,7 @@
 	vmmc-supply = <&mt6358_vmch_reg>;
 	vqmmc-supply = <&mt6358_vmc_reg>;
 	keep-power-in-suspend;
-	enable-sdio-wakeup;
+	wakeup-source;
 	non-removable;
 };
 
@@ -404,6 +412,42 @@
 
 };
 
+&cci {
+	proc-supply = <&mt6358_vproc12_reg>;
+};
+
+&cpu0 {
+	proc-supply = <&mt6358_vproc12_reg>;
+};
+
+&cpu1 {
+	proc-supply = <&mt6358_vproc12_reg>;
+};
+
+&cpu2 {
+	proc-supply = <&mt6358_vproc12_reg>;
+};
+
+&cpu3 {
+	proc-supply = <&mt6358_vproc12_reg>;
+};
+
+&cpu4 {
+	proc-supply = <&mt6358_vproc11_reg>;
+};
+
+&cpu5 {
+	proc-supply = <&mt6358_vproc11_reg>;
+};
+
+&cpu6 {
+	proc-supply = <&mt6358_vproc11_reg>;
+};
+
+&cpu7 {
+	proc-supply = <&mt6358_vproc11_reg>;
+};
+
 &uart0 {
 	status = "okay";
 };
diff --git a/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi-cozmo.dts b/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi-cozmo.dts
new file mode 100644
index 000000000000..072133fb0f01
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi-cozmo.dts
@@ -0,0 +1,36 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright 2021 Google LLC
+ */
+
+/dts-v1/;
+#include "mt8183-kukui-jacuzzi.dtsi"
+#include "mt8183-kukui-audio-ts3a227e-max98357a.dtsi"
+
+/ {
+	model = "Google cozmo board";
+	compatible = "google,cozmo", "mediatek,mt8183";
+};
+
+&i2c_tunnel {
+	google,remote-bus = <0>;
+};
+
+&i2c2 {
+	trackpad@2c {
+		compatible = "hid-over-i2c";
+		reg = <0x2c>;
+		hid-descr-addr = <0x20>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&trackpad_pins>;
+
+		interrupts-extended = <&pio 7 IRQ_TYPE_LEVEL_LOW>;
+
+		wakeup-source;
+	};
+};
+
+&qca_wifi {
+	qcom,ath10k-calibration-variant = "GO_COZMO";
+};
diff --git a/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi-fennel-sku1.dts b/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi-fennel-sku1.dts
index ef6257c9a2d2..dec11a4eb59e 100644
--- a/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi-fennel-sku1.dts
+++ b/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi-fennel-sku1.dts
@@ -5,6 +5,7 @@
 
 /dts-v1/;
 #include "mt8183-kukui-jacuzzi-fennel.dtsi"
+#include "mt8183-kukui-audio-da7219-rt1015p.dtsi"
 
 / {
 	model = "Google fennel sku1 board";
diff --git a/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi-fennel-sku6.dts b/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi-fennel-sku6.dts
index 899c2e42385c..37e6e58f63b7 100644
--- a/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi-fennel-sku6.dts
+++ b/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi-fennel-sku6.dts
@@ -5,6 +5,7 @@
 
 /dts-v1/;
 #include "mt8183-kukui-jacuzzi-fennel.dtsi"
+#include "mt8183-kukui-audio-da7219-rt1015p.dtsi"
 
 / {
 	model = "Google fennel sku6 board";
diff --git a/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi-fennel-sku7.dts b/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi-fennel-sku7.dts
new file mode 100644
index 000000000000..0e09604004d5
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi-fennel-sku7.dts
@@ -0,0 +1,33 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright 2021 Google LLC
+ */
+
+/dts-v1/;
+#include "mt8183-kukui-jacuzzi-fennel.dtsi"
+#include "mt8183-kukui-audio-ts3a227e-rt1015p.dtsi"
+
+/ {
+	model = "Google fennel sku7 board";
+	compatible = "google,fennel-sku7", "google,fennel", "mediatek,mt8183";
+};
+
+&touchscreen {
+	status = "okay";
+
+	compatible = "hid-over-i2c";
+	reg = <0x10>;
+	interrupt-parent = <&pio>;
+	interrupts = <155 IRQ_TYPE_LEVEL_LOW>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&touchscreen_pins>;
+
+	post-power-on-delay-ms = <10>;
+	hid-descr-addr = <0x0001>;
+};
+
+
+&qca_wifi {
+	qcom,ath10k-calibration-variant = "GO_FENNEL";
+};
+
diff --git a/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi-fennel.dtsi b/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi-fennel.dtsi
index 577519a775c0..bbe6c338f465 100644
--- a/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi-fennel.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi-fennel.dtsi
@@ -5,7 +5,6 @@
 
 /dts-v1/;
 #include "mt8183-kukui-jacuzzi.dtsi"
-#include "mt8183-kukui-audio-da7219-rt1015p.dtsi"
 
 &mt6358codec {
 	mediatek,dmic-mode = <1>; /* one-wire */
diff --git a/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi-fennel14-sku2.dts b/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi-fennel14-sku2.dts
new file mode 100644
index 000000000000..3fc5a6181d7e
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi-fennel14-sku2.dts
@@ -0,0 +1,17 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright 2021 Google LLC
+ */
+
+/dts-v1/;
+#include "mt8183-kukui-jacuzzi-fennel.dtsi"
+#include "mt8183-kukui-audio-ts3a227e-rt1015p.dtsi"
+
+/ {
+	model = "Google fennel14 sku2 board";
+	compatible = "google,fennel-sku2", "google,fennel", "mediatek,mt8183";
+};
+
+&qca_wifi {
+	qcom,ath10k-calibration-variant = "GO_FENNEL14";
+};
diff --git a/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi-fennel14.dts b/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi-fennel14.dts
index e8c41f6b4b0d..23ad0b91e977 100644
--- a/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi-fennel14.dts
+++ b/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi-fennel14.dts
@@ -5,6 +5,7 @@
 
 /dts-v1/;
 #include "mt8183-kukui-jacuzzi-fennel.dtsi"
+#include "mt8183-kukui-audio-da7219-rt1015p.dtsi"
 
 / {
 	model = "Google fennel14 sku0 board";
diff --git a/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi.dtsi b/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi.dtsi
index d8826c82bcda..3ac83be53627 100644
--- a/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt8183-kukui-jacuzzi.dtsi
@@ -9,7 +9,6 @@
 	panel: panel {
 		compatible = "auo,b116xw03";
 		power-supply = <&pp3300_panel>;
-		ddc-i2c-bus = <&i2c4>;
 		backlight = <&backlight_lcd0>;
 
 		port {
@@ -74,7 +73,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&volume_button_pins>;
 
-		volume_down {
+		button-volume-down {
 			label = "Volume Down";
 			linux,code = <KEY_VOLUMEDOWN>;
 			debounce-interval = <100>;
@@ -82,7 +81,7 @@
 			gpios = <&pio 6 GPIO_ACTIVE_LOW>;
 		};
 
-		volume_up {
+		button-volume-up {
 			label = "Volume Up";
 			linux,code = <KEY_VOLUMEUP>;
 			debounce-interval = <100>;
@@ -93,7 +92,7 @@
 };
 
 &cros_ec {
-	cros_ec_pwm: ec-pwm {
+	cros_ec_pwm: pwm {
 		compatible = "google,cros-ec-pwm";
 		#pwm-cells = <1>;
 		status = "disabled";
diff --git a/arch/arm64/boot/dts/mediatek/mt8183-kukui-kakadu-sku22.dts b/arch/arm64/boot/dts/mediatek/mt8183-kukui-kakadu-sku22.dts
new file mode 100644
index 000000000000..3a724e6f915c
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt8183-kukui-kakadu-sku22.dts
@@ -0,0 +1,19 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright 2021 Google LLC
+ */
+
+/dts-v1/;
+#include "mt8183-kukui-kakadu.dtsi"
+#include "mt8183-kukui-audio-rt1015p.dtsi"
+
+/ {
+	model = "MediaTek kakadu board sku22";
+	compatible = "google,kakadu-rev3-sku22", "google,kakadu-rev2-sku22",
+		     "google,kakadu", "mediatek,mt8183";
+};
+
+&sound {
+	compatible = "mediatek,mt8183_mt6358_ts3a227_rt1015p";
+};
+
diff --git a/arch/arm64/boot/dts/mediatek/mt8183-kukui-kakadu.dtsi b/arch/arm64/boot/dts/mediatek/mt8183-kukui-kakadu.dtsi
index 28966a65391b..50a0dd36b5fb 100644
--- a/arch/arm64/boot/dts/mediatek/mt8183-kukui-kakadu.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt8183-kukui-kakadu.dtsi
@@ -45,7 +45,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pen_eject>;
 
-		pen-insert {
+		switch-pen-insert {
 			label = "Pen Insert";
 			/* Insert = low, eject = high */
 			gpios = <&pio 6 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm64/boot/dts/mediatek/mt8183-kukui.dtsi b/arch/arm64/boot/dts/mediatek/mt8183-kukui.dtsi
index b42d81d26d72..b4b86bb1f1a7 100644
--- a/arch/arm64/boot/dts/mediatek/mt8183-kukui.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt8183-kukui.dtsi
@@ -144,7 +144,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&wifi_pins_wakeup>;
 
-		wowlan {
+		button-wowlan {
 			label = "Wake on WiFi";
 			gpios = <&pio 113 GPIO_ACTIVE_HIGH>;
 			linux,code = <KEY_WAKEUP>;
@@ -157,33 +157,33 @@
 		#thermal-sensor-cells = <0>;
 		io-channels = <&auxadc 0>;
 		io-channel-names = "sensor-channel";
-		temperature-lookup-table = <    (-5000) 4241
-						0 4063
-						5000 3856
-						10000 3621
-						15000 3364
-						20000 3091
-						25000 2810
-						30000 2526
-						35000 2247
-						40000 1982
-						45000 1734
-						50000 1507
-						55000 1305
-						60000 1122
-						65000 964
-						70000 827
-						75000 710
-						80000 606
-						85000 519
-						90000 445
-						95000 382
-						100000 330
-						105000 284
-						110000 245
-						115000 213
-						120000 183
-						125000 161>;
+		temperature-lookup-table = <    (-5000) 1553
+						0 1488
+						5000 1412
+						10000 1326
+						15000 1232
+						20000 1132
+						25000 1029
+						30000 925
+						35000 823
+						40000 726
+						45000 635
+						50000 552
+						55000 478
+						60000 411
+						65000 353
+						70000 303
+						75000 260
+						80000 222
+						85000 190
+						90000 163
+						95000 140
+						100000 121
+						105000 104
+						110000 90
+						115000 78
+						120000 67
+						125000 59>;
 	};
 
 	tboard_thermistor2: thermal-sensor2 {
@@ -191,33 +191,33 @@
 		#thermal-sensor-cells = <0>;
 		io-channels = <&auxadc 1>;
 		io-channel-names = "sensor-channel";
-		temperature-lookup-table = <    (-5000) 4241
-						0 4063
-						5000 3856
-						10000 3621
-						15000 3364
-						20000 3091
-						25000 2810
-						30000 2526
-						35000 2247
-						40000 1982
-						45000 1734
-						50000 1507
-						55000 1305
-						60000 1122
-						65000 964
-						70000 827
-						75000 710
-						80000 606
-						85000 519
-						90000 445
-						95000 382
-						100000 330
-						105000 284
-						110000 245
-						115000 213
-						120000 183
-						125000 161>;
+		temperature-lookup-table = <    (-5000) 1553
+						0 1488
+						5000 1412
+						10000 1326
+						15000 1232
+						20000 1132
+						25000 1029
+						30000 925
+						35000 823
+						40000 726
+						45000 635
+						50000 552
+						55000 478
+						60000 411
+						65000 353
+						70000 303
+						75000 260
+						80000 222
+						85000 190
+						90000 163
+						95000 140
+						100000 121
+						105000 104
+						110000 90
+						115000 78
+						120000 67
+						125000 59>;
 	};
 };
 
@@ -230,6 +230,10 @@
 	status = "okay";
 };
 
+&cci {
+	proc-supply = <&mt6358_vproc12_reg>;
+};
+
 &cpu0 {
 	proc-supply = <&mt6358_vproc12_reg>;
 };
@@ -276,6 +280,7 @@
 		avee-supply = <&ppvarp_lcd>;
 		pp1800-supply = <&pp1800_lcd>;
 		backlight = <&backlight_lcd0>;
+		rotation = <270>;
 		port {
 			panel_in: endpoint {
 				remote-endpoint = <&dsi_out>;
@@ -378,7 +383,7 @@
 	sd-uhs-sdr50;
 	sd-uhs-sdr104;
 	keep-power-in-suspend;
-	enable-sdio-wakeup;
+	wakeup-source;
 	cap-sdio-irq;
 	non-removable;
 	no-mmc;
@@ -813,10 +818,14 @@
 
 	cros_ec {
 		compatible = "google,cros-ec-rpmsg";
-		mtk,rpmsg-name = "cros-ec-rpmsg";
+		mediatek,rpmsg-name = "cros-ec-rpmsg";
 	};
 };
 
+&mfg_async {
+	domain-supply = <&mt6358_vsram_gpu_reg>;
+};
+
 &mfg {
 	domain-supply = <&mt6358_vgpu_reg>;
 };
@@ -849,7 +858,7 @@
 	mediatek,pad-select = <0>;
 	status = "okay";
 
-	w25q64dw: spi-flash@0 {
+	w25q64dw: flash@0 {
 		compatible = "winbond,w25q64dw", "jedec,spi-nor";
 		reg = <0>;
 		spi-max-frequency = <25000000>;
@@ -886,6 +895,20 @@
 		cbas {
 			compatible = "google,cros-cbas";
 		};
+
+		typec {
+			compatible = "google,cros-ec-typec";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			usb_c0: connector@0 {
+				compatible = "usb-c-connector";
+				reg = <0>;
+				power-role = "dual";
+				data-role = "host";
+				try-power-role = "sink";
+			};
+		};
 	};
 };
 
diff --git a/arch/arm64/boot/dts/mediatek/mt8183-pumpkin.dts b/arch/arm64/boot/dts/mediatek/mt8183-pumpkin.dts
index ee912825cfc6..a1d01639df30 100644
--- a/arch/arm64/boot/dts/mediatek/mt8183-pumpkin.dts
+++ b/arch/arm64/boot/dts/mediatek/mt8183-pumpkin.dts
@@ -7,6 +7,7 @@
 /dts-v1/;
 
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
 #include "mt8183.dtsi"
 #include "mt6358.dtsi"
 
@@ -55,7 +56,7 @@
 		};
 	};
 
-	ntc {
+	thermistor {
 		compatible = "murata,ncp03wf104";
 		pullup-uv = <1800000>;
 		pullup-ohm = <390000>;
@@ -122,6 +123,18 @@
 	clock-frequency = <100000>;
 };
 
+&keyboard {
+	pinctrl-names = "default";
+	pinctrl-0 = <&keyboard_pins>;
+	status = "okay";
+	linux,keymap = <MATRIX_KEY(0x00, 0x00, KEY_VOLUMEDOWN)
+			MATRIX_KEY(0x01, 0x00, KEY_VOLUMEUP)>;
+	keypad,num-rows = <2>;
+	keypad,num-columns = <1>;
+	debounce-delay-ms = <32>;
+	mediatek,keys-per-group = <2>;
+};
+
 &mmc0 {
 	status = "okay";
 	pinctrl-names = "default", "state_uhs";
@@ -159,7 +172,7 @@
 	vmmc-supply = <&mt6358_vmch_reg>;
 	vqmmc-supply = <&mt6358_vmc_reg>;
 	keep-power-in-suspend;
-	enable-sdio-wakeup;
+	wakeup-source;
 	non-removable;
 };
 
@@ -226,6 +239,14 @@
 		};
 	};
 
+	keyboard_pins: keyboard {
+		pins_keyboard {
+			pinmux = <PINMUX_GPIO91__FUNC_KPROW1>,
+				 <PINMUX_GPIO92__FUNC_KPROW0>,
+				 <PINMUX_GPIO93__FUNC_KPCOL0>;
+		};
+	};
+
 	mmc0_pins_default: mmc0-pins-default {
 		pins_cmd_dat {
 			pinmux = <PINMUX_GPIO123__FUNC_MSDC0_DAT0>,
diff --git a/arch/arm64/boot/dts/mediatek/mt8183.dtsi b/arch/arm64/boot/dts/mediatek/mt8183.dtsi
index ba4584faca5a..a70b669c49ba 100644
--- a/arch/arm64/boot/dts/mediatek/mt8183.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt8183.dtsi
@@ -42,6 +42,252 @@
 		rdma1 = &rdma1;
 	};
 
+	cluster0_opp: opp-table-cluster0 {
+		compatible = "operating-points-v2";
+		opp-shared;
+		opp0-793000000 {
+			opp-hz = /bits/ 64 <793000000>;
+			opp-microvolt = <650000>;
+			required-opps = <&opp2_00>;
+		};
+		opp0-910000000 {
+			opp-hz = /bits/ 64 <910000000>;
+			opp-microvolt = <687500>;
+			required-opps = <&opp2_01>;
+		};
+		opp0-1014000000 {
+			opp-hz = /bits/ 64 <1014000000>;
+			opp-microvolt = <718750>;
+			required-opps = <&opp2_02>;
+		};
+		opp0-1131000000 {
+			opp-hz = /bits/ 64 <1131000000>;
+			opp-microvolt = <756250>;
+			required-opps = <&opp2_03>;
+		};
+		opp0-1248000000 {
+			opp-hz = /bits/ 64 <1248000000>;
+			opp-microvolt = <800000>;
+			required-opps = <&opp2_04>;
+		};
+		opp0-1326000000 {
+			opp-hz = /bits/ 64 <1326000000>;
+			opp-microvolt = <818750>;
+			required-opps = <&opp2_05>;
+		};
+		opp0-1417000000 {
+			opp-hz = /bits/ 64 <1417000000>;
+			opp-microvolt = <850000>;
+			required-opps = <&opp2_06>;
+		};
+		opp0-1508000000 {
+			opp-hz = /bits/ 64 <1508000000>;
+			opp-microvolt = <868750>;
+			required-opps = <&opp2_07>;
+		};
+		opp0-1586000000 {
+			opp-hz = /bits/ 64 <1586000000>;
+			opp-microvolt = <893750>;
+			required-opps = <&opp2_08>;
+		};
+		opp0-1625000000 {
+			opp-hz = /bits/ 64 <1625000000>;
+			opp-microvolt = <906250>;
+			required-opps = <&opp2_09>;
+		};
+		opp0-1677000000 {
+			opp-hz = /bits/ 64 <1677000000>;
+			opp-microvolt = <931250>;
+			required-opps = <&opp2_10>;
+		};
+		opp0-1716000000 {
+			opp-hz = /bits/ 64 <1716000000>;
+			opp-microvolt = <943750>;
+			required-opps = <&opp2_11>;
+		};
+		opp0-1781000000 {
+			opp-hz = /bits/ 64 <1781000000>;
+			opp-microvolt = <975000>;
+			required-opps = <&opp2_12>;
+		};
+		opp0-1846000000 {
+			opp-hz = /bits/ 64 <1846000000>;
+			opp-microvolt = <1000000>;
+			required-opps = <&opp2_13>;
+		};
+		opp0-1924000000 {
+			opp-hz = /bits/ 64 <1924000000>;
+			opp-microvolt = <1025000>;
+			required-opps = <&opp2_14>;
+		};
+		opp0-1989000000 {
+			opp-hz = /bits/ 64 <1989000000>;
+			opp-microvolt = <1050000>;
+			required-opps = <&opp2_15>;
+		};	};
+
+	cluster1_opp: opp-table-cluster1 {
+		compatible = "operating-points-v2";
+		opp-shared;
+		opp1-793000000 {
+			opp-hz = /bits/ 64 <793000000>;
+			opp-microvolt = <700000>;
+			required-opps = <&opp2_00>;
+		};
+		opp1-910000000 {
+			opp-hz = /bits/ 64 <910000000>;
+			opp-microvolt = <725000>;
+			required-opps = <&opp2_01>;
+		};
+		opp1-1014000000 {
+			opp-hz = /bits/ 64 <1014000000>;
+			opp-microvolt = <750000>;
+			required-opps = <&opp2_02>;
+		};
+		opp1-1131000000 {
+			opp-hz = /bits/ 64 <1131000000>;
+			opp-microvolt = <775000>;
+			required-opps = <&opp2_03>;
+		};
+		opp1-1248000000 {
+			opp-hz = /bits/ 64 <1248000000>;
+			opp-microvolt = <800000>;
+			required-opps = <&opp2_04>;
+		};
+		opp1-1326000000 {
+			opp-hz = /bits/ 64 <1326000000>;
+			opp-microvolt = <825000>;
+			required-opps = <&opp2_05>;
+		};
+		opp1-1417000000 {
+			opp-hz = /bits/ 64 <1417000000>;
+			opp-microvolt = <850000>;
+			required-opps = <&opp2_06>;
+		};
+		opp1-1508000000 {
+			opp-hz = /bits/ 64 <1508000000>;
+			opp-microvolt = <875000>;
+			required-opps = <&opp2_07>;
+		};
+		opp1-1586000000 {
+			opp-hz = /bits/ 64 <1586000000>;
+			opp-microvolt = <900000>;
+			required-opps = <&opp2_08>;
+		};
+		opp1-1625000000 {
+			opp-hz = /bits/ 64 <1625000000>;
+			opp-microvolt = <912500>;
+			required-opps = <&opp2_09>;
+		};
+		opp1-1677000000 {
+			opp-hz = /bits/ 64 <1677000000>;
+			opp-microvolt = <931250>;
+			required-opps = <&opp2_10>;
+		};
+		opp1-1716000000 {
+			opp-hz = /bits/ 64 <1716000000>;
+			opp-microvolt = <950000>;
+			required-opps = <&opp2_11>;
+		};
+		opp1-1781000000 {
+			opp-hz = /bits/ 64 <1781000000>;
+			opp-microvolt = <975000>;
+			required-opps = <&opp2_12>;
+		};
+		opp1-1846000000 {
+			opp-hz = /bits/ 64 <1846000000>;
+			opp-microvolt = <1000000>;
+			required-opps = <&opp2_13>;
+		};
+		opp1-1924000000 {
+			opp-hz = /bits/ 64 <1924000000>;
+			opp-microvolt = <1025000>;
+			required-opps = <&opp2_14>;
+		};
+		opp1-1989000000 {
+			opp-hz = /bits/ 64 <1989000000>;
+			opp-microvolt = <1050000>;
+			required-opps = <&opp2_15>;
+		};
+	};
+
+	cci_opp: opp-table-cci {
+		compatible = "operating-points-v2";
+		opp-shared;
+		opp2_00: opp-273000000 {
+			opp-hz = /bits/ 64 <273000000>;
+			opp-microvolt = <650000>;
+		};
+		opp2_01: opp-338000000 {
+			opp-hz = /bits/ 64 <338000000>;
+			opp-microvolt = <687500>;
+		};
+		opp2_02: opp-403000000 {
+			opp-hz = /bits/ 64 <403000000>;
+			opp-microvolt = <718750>;
+		};
+		opp2_03: opp-463000000 {
+			opp-hz = /bits/ 64 <463000000>;
+			opp-microvolt = <756250>;
+		};
+		opp2_04: opp-546000000 {
+			opp-hz = /bits/ 64 <546000000>;
+			opp-microvolt = <800000>;
+		};
+		opp2_05: opp-624000000 {
+			opp-hz = /bits/ 64 <624000000>;
+			opp-microvolt = <818750>;
+		};
+		opp2_06: opp-689000000 {
+			opp-hz = /bits/ 64 <689000000>;
+			opp-microvolt = <850000>;
+		};
+		opp2_07: opp-767000000 {
+			opp-hz = /bits/ 64 <767000000>;
+			opp-microvolt = <868750>;
+		};
+		opp2_08: opp-845000000 {
+			opp-hz = /bits/ 64 <845000000>;
+			opp-microvolt = <893750>;
+		};
+		opp2_09: opp-871000000 {
+			opp-hz = /bits/ 64 <871000000>;
+			opp-microvolt = <906250>;
+		};
+		opp2_10: opp-923000000 {
+			opp-hz = /bits/ 64 <923000000>;
+			opp-microvolt = <931250>;
+		};
+		opp2_11: opp-962000000 {
+			opp-hz = /bits/ 64 <962000000>;
+			opp-microvolt = <943750>;
+		};
+		opp2_12: opp-1027000000 {
+			opp-hz = /bits/ 64 <1027000000>;
+			opp-microvolt = <975000>;
+		};
+		opp2_13: opp-1092000000 {
+			opp-hz = /bits/ 64 <1092000000>;
+			opp-microvolt = <1000000>;
+		};
+		opp2_14: opp-1144000000 {
+			opp-hz = /bits/ 64 <1144000000>;
+			opp-microvolt = <1025000>;
+		};
+		opp2_15: opp-1196000000 {
+			opp-hz = /bits/ 64 <1196000000>;
+			opp-microvolt = <1050000>;
+		};
+	};
+
+	cci: cci {
+		compatible = "mediatek,mt8183-cci";
+		clocks = <&mcucfg CLK_MCU_BUS_SEL>,
+			 <&topckgen CLK_TOP_ARMPLL_DIV_PLL1>;
+		clock-names = "cci", "intermediate";
+		operating-points-v2 = <&cci_opp>;
+	};
+
 	cpus {
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -85,8 +331,13 @@
 			enable-method = "psci";
 			capacity-dmips-mhz = <741>;
 			cpu-idle-states = <&CPU_SLEEP &CLUSTER_SLEEP0>;
+			clocks = <&mcucfg CLK_MCU_MP0_SEL>,
+				 <&topckgen CLK_TOP_ARMPLL_DIV_PLL1>;
+			clock-names = "cpu", "intermediate";
+			operating-points-v2 = <&cluster0_opp>;
 			dynamic-power-coefficient = <84>;
 			#cooling-cells = <2>;
+			mediatek,cci = <&cci>;
 		};
 
 		cpu1: cpu@1 {
@@ -96,8 +347,13 @@
 			enable-method = "psci";
 			capacity-dmips-mhz = <741>;
 			cpu-idle-states = <&CPU_SLEEP &CLUSTER_SLEEP0>;
+			clocks = <&mcucfg CLK_MCU_MP0_SEL>,
+				 <&topckgen CLK_TOP_ARMPLL_DIV_PLL1>;
+			clock-names = "cpu", "intermediate";
+			operating-points-v2 = <&cluster0_opp>;
 			dynamic-power-coefficient = <84>;
 			#cooling-cells = <2>;
+			mediatek,cci = <&cci>;
 		};
 
 		cpu2: cpu@2 {
@@ -107,8 +363,13 @@
 			enable-method = "psci";
 			capacity-dmips-mhz = <741>;
 			cpu-idle-states = <&CPU_SLEEP &CLUSTER_SLEEP0>;
+			clocks = <&mcucfg CLK_MCU_MP0_SEL>,
+				 <&topckgen CLK_TOP_ARMPLL_DIV_PLL1>;
+			clock-names = "cpu", "intermediate";
+			operating-points-v2 = <&cluster0_opp>;
 			dynamic-power-coefficient = <84>;
 			#cooling-cells = <2>;
+			mediatek,cci = <&cci>;
 		};
 
 		cpu3: cpu@3 {
@@ -118,8 +379,13 @@
 			enable-method = "psci";
 			capacity-dmips-mhz = <741>;
 			cpu-idle-states = <&CPU_SLEEP &CLUSTER_SLEEP0>;
+			clocks = <&mcucfg CLK_MCU_MP0_SEL>,
+				 <&topckgen CLK_TOP_ARMPLL_DIV_PLL1>;
+			clock-names = "cpu", "intermediate";
+			operating-points-v2 = <&cluster0_opp>;
 			dynamic-power-coefficient = <84>;
 			#cooling-cells = <2>;
+			mediatek,cci = <&cci>;
 		};
 
 		cpu4: cpu@100 {
@@ -129,8 +395,13 @@
 			enable-method = "psci";
 			capacity-dmips-mhz = <1024>;
 			cpu-idle-states = <&CPU_SLEEP &CLUSTER_SLEEP1>;
+			clocks = <&mcucfg CLK_MCU_MP2_SEL>,
+				 <&topckgen CLK_TOP_ARMPLL_DIV_PLL1>;
+			clock-names = "cpu", "intermediate";
+			operating-points-v2 = <&cluster1_opp>;
 			dynamic-power-coefficient = <211>;
 			#cooling-cells = <2>;
+			mediatek,cci = <&cci>;
 		};
 
 		cpu5: cpu@101 {
@@ -140,8 +411,13 @@
 			enable-method = "psci";
 			capacity-dmips-mhz = <1024>;
 			cpu-idle-states = <&CPU_SLEEP &CLUSTER_SLEEP1>;
+			clocks = <&mcucfg CLK_MCU_MP2_SEL>,
+				 <&topckgen CLK_TOP_ARMPLL_DIV_PLL1>;
+			clock-names = "cpu", "intermediate";
+			operating-points-v2 = <&cluster1_opp>;
 			dynamic-power-coefficient = <211>;
 			#cooling-cells = <2>;
+			mediatek,cci = <&cci>;
 		};
 
 		cpu6: cpu@102 {
@@ -151,8 +427,13 @@
 			enable-method = "psci";
 			capacity-dmips-mhz = <1024>;
 			cpu-idle-states = <&CPU_SLEEP &CLUSTER_SLEEP1>;
+			clocks = <&mcucfg CLK_MCU_MP2_SEL>,
+				 <&topckgen CLK_TOP_ARMPLL_DIV_PLL1>;
+			clock-names = "cpu", "intermediate";
+			operating-points-v2 = <&cluster1_opp>;
 			dynamic-power-coefficient = <211>;
 			#cooling-cells = <2>;
+			mediatek,cci = <&cci>;
 		};
 
 		cpu7: cpu@103 {
@@ -162,8 +443,13 @@
 			enable-method = "psci";
 			capacity-dmips-mhz = <1024>;
 			cpu-idle-states = <&CPU_SLEEP &CLUSTER_SLEEP1>;
+			clocks = <&mcucfg CLK_MCU_MP2_SEL>,
+				 <&topckgen CLK_TOP_ARMPLL_DIV_PLL1>;
+			clock-names = "cpu", "intermediate";
+			operating-points-v2 = <&cluster1_opp>;
 			dynamic-power-coefficient = <211>;
 			#cooling-cells = <2>;
+			mediatek,cci = <&cci>;
 		};
 
 		idle-states {
@@ -197,7 +483,7 @@
 		};
 	};
 
-	gpu_opp_table: opp_table0 {
+	gpu_opp_table: opp-table-0 {
 		compatible = "operating-points-v2";
 		opp-shared;
 
@@ -295,8 +581,8 @@
 	};
 
 	psci {
-		compatible      = "arm,psci-1.0";
-		method          = "smc";
+		compatible = "arm,psci-1.0";
+		method = "smc";
 	};
 
 	clk26m: oscillator {
@@ -321,7 +607,7 @@
 		compatible = "simple-bus";
 		ranges;
 
-		soc_data: soc_data@8000000 {
+		soc_data: efuse@8000000 {
 			compatible = "mediatek,mt8183-efuse",
 				     "mediatek,efuse";
 			reg = <0 0x08000000 0 0x0010>;
@@ -367,6 +653,70 @@
 			reg = <0 0x0c530a80 0 0x50>;
 		};
 
+		cpu_debug0: cpu-debug@d410000 {
+			compatible = "arm,coresight-cpu-debug", "arm,primecell";
+			reg = <0x0 0xd410000 0x0 0x1000>;
+			clocks = <&infracfg CLK_INFRA_DEBUGSYS>;
+			clock-names = "apb_pclk";
+			cpu = <&cpu0>;
+		};
+
+		cpu_debug1: cpu-debug@d510000 {
+			compatible = "arm,coresight-cpu-debug", "arm,primecell";
+			reg = <0x0 0xd510000 0x0 0x1000>;
+			clocks = <&infracfg CLK_INFRA_DEBUGSYS>;
+			clock-names = "apb_pclk";
+			cpu = <&cpu1>;
+		};
+
+		cpu_debug2: cpu-debug@d610000 {
+			compatible = "arm,coresight-cpu-debug", "arm,primecell";
+			reg = <0x0 0xd610000 0x0 0x1000>;
+			clocks = <&infracfg CLK_INFRA_DEBUGSYS>;
+			clock-names = "apb_pclk";
+			cpu = <&cpu2>;
+		};
+
+		cpu_debug3: cpu-debug@d710000 {
+			compatible = "arm,coresight-cpu-debug", "arm,primecell";
+			reg = <0x0 0xd710000 0x0 0x1000>;
+			clocks = <&infracfg CLK_INFRA_DEBUGSYS>;
+			clock-names = "apb_pclk";
+			cpu = <&cpu3>;
+		};
+
+		cpu_debug4: cpu-debug@d810000 {
+			compatible = "arm,coresight-cpu-debug", "arm,primecell";
+			reg = <0x0 0xd810000 0x0 0x1000>;
+			clocks = <&infracfg CLK_INFRA_DEBUGSYS>;
+			clock-names = "apb_pclk";
+			cpu = <&cpu4>;
+		};
+
+		cpu_debug5: cpu-debug@d910000 {
+			compatible = "arm,coresight-cpu-debug", "arm,primecell";
+			reg = <0x0 0xd910000 0x0 0x1000>;
+			clocks = <&infracfg CLK_INFRA_DEBUGSYS>;
+			clock-names = "apb_pclk";
+			cpu = <&cpu5>;
+		};
+
+		cpu_debug6: cpu-debug@da10000 {
+			compatible = "arm,coresight-cpu-debug", "arm,primecell";
+			reg = <0x0 0xda10000 0x0 0x1000>;
+			clocks = <&infracfg CLK_INFRA_DEBUGSYS>;
+			clock-names = "apb_pclk";
+			cpu = <&cpu6>;
+		};
+
+		cpu_debug7: cpu-debug@db10000 {
+			compatible = "arm,coresight-cpu-debug", "arm,primecell";
+			reg = <0x0 0xdb10000 0x0 0x1000>;
+			clocks = <&infracfg CLK_INFRA_DEBUGSYS>;
+			clock-names = "apb_pclk";
+			cpu = <&cpu7>;
+		};
+
 		topckgen: syscon@10000000 {
 			compatible = "mediatek,mt8183-topckgen", "syscon";
 			reg = <0 0x10000000 0 0x1000>;
@@ -411,9 +761,8 @@
 		};
 
 		scpsys: syscon@10006000 {
-			compatible = "syscon", "simple-mfd";
+			compatible = "mediatek,mt8183-scpsys", "syscon", "simple-mfd";
 			reg = <0 0x10006000 0 0x1000>;
-			#power-domain-cells = <1>;
 
 			/* System Power Manager */
 			spm: power-controller {
@@ -438,9 +787,9 @@
 					#power-domain-cells = <0>;
 				};
 
-				power-domain@MT8183_POWER_DOMAIN_MFG_ASYNC {
+				mfg_async: power-domain@MT8183_POWER_DOMAIN_MFG_ASYNC {
 					reg = <MT8183_POWER_DOMAIN_MFG_ASYNC>;
-					clocks =  <&topckgen CLK_TOP_MUX_MFG>;
+					clocks = <&topckgen CLK_TOP_MUX_MFG>;
 					clock-names = "mfg";
 					#address-cells = <1>;
 					#size-cells = <0>;
@@ -593,6 +942,15 @@
 			clock-names = "spi", "wrap";
 		};
 
+		keyboard: keyboard@10010000 {
+			compatible = "mediatek,mt6779-keypad";
+			reg = <0 0x10010000 0 0x1000>;
+			interrupts = <GIC_SPI 186 IRQ_TYPE_EDGE_FALLING>;
+			clocks = <&clk26m>;
+			clock-names = "kpd";
+			status = "disabled";
+		};
+
 		scp: scp@10500000 {
 			compatible = "mediatek,mt8183-scp";
 			reg = <0 0x10500000 0 0x80000>,
@@ -618,8 +976,8 @@
 			compatible = "mediatek,mt8183-m4u";
 			reg = <0 0x10205000 0 0x1000>;
 			interrupts = <GIC_SPI 166 IRQ_TYPE_LEVEL_LOW>;
-			mediatek,larbs = <&larb0 &larb1 &larb2 &larb3
-					  &larb4 &larb5 &larb6>;
+			mediatek,larbs = <&larb0>, <&larb1>, <&larb2>, <&larb3>,
+					 <&larb4>, <&larb5>, <&larb6>;
 			#iommu-cells = <1>;
 		};
 
@@ -743,6 +1101,18 @@
 			status = "disabled";
 		};
 
+		svs: svs@1100b000 {
+			compatible = "mediatek,mt8183-svs";
+			reg = <0 0x1100b000 0 0x1000>;
+			interrupts = <GIC_SPI 127 IRQ_TYPE_LEVEL_LOW>;
+			clocks = <&infracfg CLK_INFRA_THERM>;
+			clock-names = "main";
+			nvmem-cells = <&svs_calibration>,
+				      <&thermal_calibration>;
+			nvmem-cell-names = "svs-calibration-data",
+					   "t-calibration-data";
+		};
+
 		thermal: thermal@1100b000 {
 			#thermal-sensor-cells = <1>;
 			compatible = "mediatek,mt8183-thermal";
@@ -759,7 +1129,7 @@
 		};
 
 		thermal_zones: thermal-zones {
-			cpu_thermal: cpu_thermal {
+			cpu_thermal: cpu-thermal {
 				polling-delay-passive = <100>;
 				polling-delay = <500>;
 				thermal-sensors = <&thermal 0>;
@@ -1086,7 +1456,7 @@
 		};
 
 		ssusb: usb@11201000 {
-			compatible ="mediatek,mt8183-mtu3", "mediatek,mtu3";
+			compatible = "mediatek,mt8183-mtu3", "mediatek,mtu3";
 			reg = <0 0x11201000 0 0x2e00>,
 			      <0 0x11203e00 0 0x0100>;
 			reg-names = "mac", "ippc";
@@ -1261,6 +1631,10 @@
 			mipi_tx_calibration: calib@190 {
 				reg = <0x190 0xc>;
 			};
+
+			svs_calibration: calib@580 {
+				reg = <0x580 0x64>;
+			};
 		};
 
 		u3phy: t-phy@11f40000 {
@@ -1325,6 +1699,60 @@
 			mediatek,gce-client-reg = <&gce SUBSYS_1400XXXX 0 0x1000>;
 		};
 
+		mdp3-rdma0@14001000 {
+			compatible = "mediatek,mt8183-mdp3-rdma";
+			reg = <0 0x14001000 0 0x1000>;
+			mediatek,gce-client-reg = <&gce SUBSYS_1400XXXX 0x1000 0x1000>;
+			mediatek,gce-events = <CMDQ_EVENT_MDP_RDMA0_SOF>,
+					      <CMDQ_EVENT_MDP_RDMA0_EOF>;
+			power-domains = <&spm MT8183_POWER_DOMAIN_DISP>;
+			clocks = <&mmsys CLK_MM_MDP_RDMA0>,
+				 <&mmsys CLK_MM_MDP_RSZ1>;
+			iommus = <&iommu M4U_PORT_MDP_RDMA0>;
+			mboxes = <&gce 20 CMDQ_THR_PRIO_LOWEST 0>,
+				 <&gce 21 CMDQ_THR_PRIO_LOWEST 0>;
+		};
+
+		mdp3-rsz0@14003000 {
+			compatible = "mediatek,mt8183-mdp3-rsz";
+			reg = <0 0x14003000 0 0x1000>;
+			mediatek,gce-client-reg = <&gce SUBSYS_1400XXXX 0x3000 0x1000>;
+			mediatek,gce-events = <CMDQ_EVENT_MDP_RSZ0_SOF>,
+					      <CMDQ_EVENT_MDP_RSZ0_EOF>;
+			clocks = <&mmsys CLK_MM_MDP_RSZ0>;
+		};
+
+		mdp3-rsz1@14004000 {
+			compatible = "mediatek,mt8183-mdp3-rsz";
+			reg = <0 0x14004000 0 0x1000>;
+			mediatek,gce-client-reg = <&gce SUBSYS_1400XXXX 0x4000 0x1000>;
+			mediatek,gce-events = <CMDQ_EVENT_MDP_RSZ1_SOF>,
+					      <CMDQ_EVENT_MDP_RSZ1_EOF>;
+			clocks = <&mmsys CLK_MM_MDP_RSZ1>;
+		};
+
+		mdp3-wrot0@14005000 {
+			compatible = "mediatek,mt8183-mdp3-wrot";
+			reg = <0 0x14005000 0 0x1000>;
+			mediatek,gce-client-reg = <&gce SUBSYS_1400XXXX 0x5000 0x1000>;
+			mediatek,gce-events = <CMDQ_EVENT_MDP_WROT0_SOF>,
+					      <CMDQ_EVENT_MDP_WROT0_EOF>;
+			power-domains = <&spm MT8183_POWER_DOMAIN_DISP>;
+			clocks = <&mmsys CLK_MM_MDP_WROT0>;
+			iommus = <&iommu M4U_PORT_MDP_WROT0>;
+		};
+
+		mdp3-wdma@14006000 {
+			compatible = "mediatek,mt8183-mdp3-wdma";
+			reg = <0 0x14006000 0 0x1000>;
+			mediatek,gce-client-reg = <&gce SUBSYS_1400XXXX 0x6000 0x1000>;
+			mediatek,gce-events = <CMDQ_EVENT_MDP_WDMA0_SOF>,
+					      <CMDQ_EVENT_MDP_WDMA0_EOF>;
+			power-domains = <&spm MT8183_POWER_DOMAIN_DISP>;
+			clocks = <&mmsys CLK_MM_MDP_WDMA0>;
+			iommus = <&iommu M4U_PORT_MDP_WDMA0>;
+		};
+
 		ovl0: ovl@14008000 {
 			compatible = "mediatek,mt8183-disp-ovl";
 			reg = <0 0x14008000 0 0x1000>;
@@ -1332,7 +1760,6 @@
 			power-domains = <&spm MT8183_POWER_DOMAIN_DISP>;
 			clocks = <&mmsys CLK_MM_DISP_OVL0>;
 			iommus = <&iommu M4U_PORT_DISP_OVL0>;
-			mediatek,larb = <&larb0>;
 			mediatek,gce-client-reg = <&gce SUBSYS_1400XXXX 0x8000 0x1000>;
 		};
 
@@ -1343,7 +1770,6 @@
 			power-domains = <&spm MT8183_POWER_DOMAIN_DISP>;
 			clocks = <&mmsys CLK_MM_DISP_OVL0_2L>;
 			iommus = <&iommu M4U_PORT_DISP_2L_OVL0_LARB0>;
-			mediatek,larb = <&larb0>;
 			mediatek,gce-client-reg = <&gce SUBSYS_1400XXXX 0x9000 0x1000>;
 		};
 
@@ -1354,7 +1780,6 @@
 			power-domains = <&spm MT8183_POWER_DOMAIN_DISP>;
 			clocks = <&mmsys CLK_MM_DISP_OVL1_2L>;
 			iommus = <&iommu M4U_PORT_DISP_2L_OVL1_LARB0>;
-			mediatek,larb = <&larb0>;
 			mediatek,gce-client-reg = <&gce SUBSYS_1400XXXX 0xa000 0x1000>;
 		};
 
@@ -1365,7 +1790,6 @@
 			power-domains = <&spm MT8183_POWER_DOMAIN_DISP>;
 			clocks = <&mmsys CLK_MM_DISP_RDMA0>;
 			iommus = <&iommu M4U_PORT_DISP_RDMA0>;
-			mediatek,larb = <&larb0>;
 			mediatek,rdma-fifo-size = <5120>;
 			mediatek,gce-client-reg = <&gce SUBSYS_1400XXXX 0xb000 0x1000>;
 		};
@@ -1377,7 +1801,6 @@
 			power-domains = <&spm MT8183_POWER_DOMAIN_DISP>;
 			clocks = <&mmsys CLK_MM_DISP_RDMA1>;
 			iommus = <&iommu M4U_PORT_DISP_RDMA1>;
-			mediatek,larb = <&larb0>;
 			mediatek,rdma-fifo-size = <2048>;
 			mediatek,gce-client-reg = <&gce SUBSYS_1400XXXX 0xc000 0x1000>;
 		};
@@ -1402,8 +1825,7 @@
 		};
 
 		aal0: aal@14010000 {
-			compatible = "mediatek,mt8183-disp-aal",
-				     "mediatek,mt8173-disp-aal";
+			compatible = "mediatek,mt8183-disp-aal";
 			reg = <0 0x14010000 0 0x1000>;
 			interrupts = <GIC_SPI 233 IRQ_TYPE_LEVEL_LOW>;
 			power-domains = <&spm MT8183_POWER_DOMAIN_DISP>;
@@ -1450,6 +1872,7 @@
 			power-domains = <&spm MT8183_POWER_DOMAIN_DISP>;
 			mediatek,gce-events = <CMDQ_EVENT_MUTEX_STREAM_DONE0>,
 					      <CMDQ_EVENT_MUTEX_STREAM_DONE1>;
+			mediatek,gce-client-reg = <&gce SUBSYS_1401XXXX 0x6000 0x1000>;
 		};
 
 		larb0: larb@14017000 {
@@ -1473,6 +1896,15 @@
 			power-domains = <&spm MT8183_POWER_DOMAIN_DISP>;
 		};
 
+		mdp3-ccorr@1401c000 {
+			compatible = "mediatek,mt8183-mdp3-ccorr";
+			reg = <0 0x1401c000 0 0x1000>;
+			mediatek,gce-client-reg = <&gce SUBSYS_1401XXXX 0xc000 0x1000>;
+			mediatek,gce-events = <CMDQ_EVENT_MDP_CCORR_SOF>,
+					      <CMDQ_EVENT_MDP_CCORR_EOF>;
+			clocks = <&mmsys CLK_MM_MDP_CCORR>;
+		};
+
 		imgsys: syscon@15020000 {
 			compatible = "mediatek,mt8183-imgsys", "syscon";
 			reg = <0 0x15020000 0 0x1000>;
@@ -1530,6 +1962,17 @@
 			power-domains = <&spm MT8183_POWER_DOMAIN_VENC>;
 		};
 
+		venc_jpg: venc_jpg@17030000 {
+			compatible = "mediatek,mt8183-jpgenc", "mediatek,mtk-jpgenc";
+			reg = <0 0x17030000 0 0x1000>;
+			interrupts = <GIC_SPI 249 IRQ_TYPE_LEVEL_LOW>;
+			iommus = <&iommu M4U_PORT_JPGENC_RDMA>,
+				 <&iommu M4U_PORT_JPGENC_BSDMA>;
+			power-domains = <&spm MT8183_POWER_DOMAIN_VENC>;
+			clocks = <&vencsys CLK_VENC_JPGENC>;
+			clock-names = "jpgenc";
+		};
+
 		ipu_conn: syscon@19000000 {
 			compatible = "mediatek,mt8183-ipu_conn", "syscon";
 			reg = <0 0x19000000 0 0x1000>;
diff --git a/arch/arm64/boot/dts/mediatek/mt8186-evb.dts b/arch/arm64/boot/dts/mediatek/mt8186-evb.dts
new file mode 100644
index 000000000000..ed74a3617c13
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt8186-evb.dts
@@ -0,0 +1,220 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+/*
+ * Copyright (C) 2022 MediaTek Inc.
+ */
+/dts-v1/;
+#include "mt8186.dtsi"
+
+/ {
+	model = "MediaTek MT8186 evaluation board";
+	compatible = "mediatek,mt8186-evb", "mediatek,mt8186";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:921600n8";
+	};
+
+	memory@40000000 {
+		device_type = "memory";
+		reg = <0 0x40000000 0 0x80000000>;
+	};
+};
+
+&i2c0 {
+	status = "okay";
+
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins>;
+};
+
+&i2c1 {
+	status = "okay";
+
+	clock-frequency = <400000>;
+	i2c-scl-internal-delay-ns = <8000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+};
+
+&i2c2 {
+	status = "okay";
+
+	clock-frequency = <400000>;
+	i2c-scl-internal-delay-ns = <10000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2_pins>;
+};
+
+&i2c3 {
+	status = "okay";
+
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c3_pins>;
+};
+
+&i2c4 {
+	status = "okay";
+
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c4_pins>;
+};
+
+&i2c5 {
+	status = "okay";
+
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c5_pins>;
+};
+
+&i2c6 {
+	status = "okay";
+
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c6_pins>;
+};
+
+&i2c7 {
+	status = "okay";
+
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c7_pins>;
+};
+
+&i2c8 {
+	status = "okay";
+
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c8_pins>;
+};
+
+&i2c9 {
+	status = "okay";
+
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c9_pins>;
+};
+
+&pio {
+	i2c0_pins: i2c0-default-pins {
+		pins-bus {
+			pinmux = <PINMUX_GPIO128__FUNC_SDA0>,
+				 <PINMUX_GPIO127__FUNC_SCL0>;
+			bias-disable;
+			drive-strength-microamp = <1000>;
+			input-enable;
+		};
+	};
+
+	i2c1_pins: i2c1-default-pins {
+		pins-bus {
+			pinmux = <PINMUX_GPIO130__FUNC_SDA1>,
+				 <PINMUX_GPIO129__FUNC_SCL1>;
+			bias-disable;
+			drive-strength-microamp = <1000>;
+			input-enable;
+		};
+	};
+
+	i2c2_pins: i2c2-default-pins {
+		pins-bus {
+			pinmux = <PINMUX_GPIO132__FUNC_SDA2>,
+				 <PINMUX_GPIO131__FUNC_SCL2>;
+			bias-disable;
+			drive-strength-microamp = <1000>;
+			input-enable;
+		};
+	};
+
+	i2c3_pins: i2c3-default-pins {
+		pins-bus {
+			pinmux = <PINMUX_GPIO134__FUNC_SDA3>,
+				 <PINMUX_GPIO133__FUNC_SCL3>;
+			bias-disable;
+			drive-strength-microamp = <1000>;
+			input-enable;
+		};
+	};
+
+	i2c4_pins: i2c4-default-pins {
+		pins-bus {
+			pinmux = <PINMUX_GPIO136__FUNC_SDA4>,
+				 <PINMUX_GPIO135__FUNC_SCL4>;
+			bias-disable;
+			drive-strength-microamp = <1000>;
+			input-enable;
+		};
+	};
+
+	i2c5_pins: i2c5-default-pins {
+		pins-bus {
+			pinmux = <PINMUX_GPIO138__FUNC_SDA5>,
+				 <PINMUX_GPIO137__FUNC_SCL5>;
+			bias-disable;
+			drive-strength-microamp = <1000>;
+			input-enable;
+		};
+	};
+
+	i2c6_pins: i2c6-default-pins {
+		pins-bus {
+			pinmux = <PINMUX_GPIO140__FUNC_SDA6>,
+				 <PINMUX_GPIO139__FUNC_SCL6>;
+			bias-pull-up = <MTK_PULL_SET_RSEL_001>;
+			drive-strength-microamp = <1000>;
+			input-enable;
+		};
+	};
+
+	i2c7_pins: i2c7-default-pins {
+		pins-bus {
+			pinmux = <PINMUX_GPIO142__FUNC_SDA7>,
+				 <PINMUX_GPIO141__FUNC_SCL7>;
+			bias-disable;
+			drive-strength-microamp = <1000>;
+			input-enable;
+		};
+	};
+
+	i2c8_pins: i2c8-default-pins {
+		pins-bus {
+			pinmux = <PINMUX_GPIO144__FUNC_SDA8>,
+				 <PINMUX_GPIO143__FUNC_SCL8>;
+			bias-disable;
+			drive-strength-microamp = <1000>;
+			input-enable;
+		};
+	};
+
+	i2c9_pins: i2c9-default-pins {
+		pins-bus {
+			pinmux = <PINMUX_GPIO146__FUNC_SDA9>,
+				 <PINMUX_GPIO145__FUNC_SCL9>;
+			bias-pull-up = <MTK_PULL_SET_RSEL_001>;
+			drive-strength-microamp = <1000>;
+			input-enable;
+		};
+	};
+};
+
+&u3phy0 {
+	status = "okay";
+};
+
+&u3phy1 {
+	status = "okay";
+};
+
+&uart0 {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/mediatek/mt8186.dtsi b/arch/arm64/boot/dts/mediatek/mt8186.dtsi
new file mode 100644
index 000000000000..64693c17af9e
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt8186.dtsi
@@ -0,0 +1,819 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+/*
+ * Copyright (C) 2022 MediaTek Inc.
+ * Author: Allen-KH Cheng <allen-kh.cheng@mediatek.com>
+ */
+/dts-v1/;
+#include <dt-bindings/clock/mt8186-clk.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/pinctrl/mt8186-pinfunc.h>
+#include <dt-bindings/power/mt8186-power.h>
+#include <dt-bindings/phy/phy.h>
+#include <dt-bindings/reset/mt8186-resets.h>
+
+/ {
+	compatible = "mediatek,mt8186";
+	interrupt-parent = <&gic>;
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu-map {
+			cluster0 {
+				core0 {
+					cpu = <&cpu0>;
+				};
+
+				core1 {
+					cpu = <&cpu1>;
+				};
+
+				core2 {
+					cpu = <&cpu2>;
+				};
+
+				core3 {
+					cpu = <&cpu3>;
+				};
+
+				core4 {
+					cpu = <&cpu4>;
+				};
+
+				core5 {
+					cpu = <&cpu5>;
+				};
+			};
+
+			cluster1 {
+				core0 {
+					cpu = <&cpu6>;
+				};
+
+				core1 {
+					cpu = <&cpu7>;
+				};
+			};
+		};
+
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a55";
+			reg = <0x000>;
+			enable-method = "psci";
+			clock-frequency = <2000000000>;
+			capacity-dmips-mhz = <382>;
+			cpu-idle-states = <&cpu_off_l &cluster_off_l>;
+			next-level-cache = <&l2_0>;
+			#cooling-cells = <2>;
+		};
+
+		cpu1: cpu@100 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a55";
+			reg = <0x100>;
+			enable-method = "psci";
+			clock-frequency = <2000000000>;
+			capacity-dmips-mhz = <382>;
+			cpu-idle-states = <&cpu_off_l &cluster_off_l>;
+			next-level-cache = <&l2_0>;
+			#cooling-cells = <2>;
+		};
+
+		cpu2: cpu@200 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a55";
+			reg = <0x200>;
+			enable-method = "psci";
+			clock-frequency = <2000000000>;
+			capacity-dmips-mhz = <382>;
+			cpu-idle-states = <&cpu_off_l &cluster_off_l>;
+			next-level-cache = <&l2_0>;
+			#cooling-cells = <2>;
+		};
+
+		cpu3: cpu@300 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a55";
+			reg = <0x300>;
+			enable-method = "psci";
+			clock-frequency = <2000000000>;
+			capacity-dmips-mhz = <382>;
+			cpu-idle-states = <&cpu_off_l &cluster_off_l>;
+			next-level-cache = <&l2_0>;
+			#cooling-cells = <2>;
+		};
+
+		cpu4: cpu@400 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a55";
+			reg = <0x400>;
+			enable-method = "psci";
+			clock-frequency = <2000000000>;
+			capacity-dmips-mhz = <382>;
+			cpu-idle-states = <&cpu_off_l &cluster_off_l>;
+			next-level-cache = <&l2_0>;
+			#cooling-cells = <2>;
+		};
+
+		cpu5: cpu@500 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a55";
+			reg = <0x500>;
+			enable-method = "psci";
+			clock-frequency = <2000000000>;
+			capacity-dmips-mhz = <382>;
+			cpu-idle-states = <&cpu_off_l &cluster_off_l>;
+			next-level-cache = <&l2_0>;
+			#cooling-cells = <2>;
+		};
+
+		cpu6: cpu@600 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a76";
+			reg = <0x600>;
+			enable-method = "psci";
+			clock-frequency = <2050000000>;
+			capacity-dmips-mhz = <1024>;
+			cpu-idle-states = <&cpu_off_b &cluster_off_b>;
+			next-level-cache = <&l2_1>;
+			#cooling-cells = <2>;
+		};
+
+		cpu7: cpu@700 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a76";
+			reg = <0x700>;
+			enable-method = "psci";
+			clock-frequency = <2050000000>;
+			capacity-dmips-mhz = <1024>;
+			cpu-idle-states = <&cpu_off_b &cluster_off_b>;
+			next-level-cache = <&l2_1>;
+			#cooling-cells = <2>;
+		};
+
+		idle-states {
+			entry-method = "psci";
+
+			cpu_off_l: cpu-off-l {
+				compatible = "arm,idle-state";
+				arm,psci-suspend-param = <0x00010001>;
+				local-timer-stop;
+				entry-latency-us = <50>;
+				exit-latency-us = <100>;
+				min-residency-us = <1600>;
+			};
+
+			cpu_off_b: cpu-off-b {
+				compatible = "arm,idle-state";
+				arm,psci-suspend-param = <0x00010001>;
+				local-timer-stop;
+				entry-latency-us = <50>;
+				exit-latency-us = <100>;
+				min-residency-us = <1400>;
+			};
+
+			cluster_off_l: cluster-off-l {
+				compatible = "arm,idle-state";
+				arm,psci-suspend-param = <0x01010001>;
+				local-timer-stop;
+				entry-latency-us = <100>;
+				exit-latency-us = <250>;
+				min-residency-us = <2100>;
+			};
+
+			cluster_off_b: cluster-off-b {
+				compatible = "arm,idle-state";
+				arm,psci-suspend-param = <0x01010001>;
+				local-timer-stop;
+				entry-latency-us = <100>;
+				exit-latency-us = <250>;
+				min-residency-us = <1900>;
+			};
+		};
+
+		l2_0: l2-cache0 {
+			compatible = "cache";
+			next-level-cache = <&l3_0>;
+		};
+
+		l2_1: l2-cache1 {
+			compatible = "cache";
+			next-level-cache = <&l3_0>;
+		};
+
+		l3_0: l3-cache {
+			compatible = "cache";
+		};
+	};
+
+	clk13m: oscillator-13m {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <13000000>;
+		clock-output-names = "clk13m";
+	};
+
+	clk26m: oscillator-26m {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <26000000>;
+		clock-output-names = "clk26m";
+	};
+
+	clk32k: oscillator-32k {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		clock-output-names = "clk32k";
+	};
+
+	pmu-a55 {
+		compatible = "arm,cortex-a55-pmu";
+		interrupt-parent = <&gic>;
+		interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH &ppi_cluster0>;
+	};
+
+	pmu-a76 {
+		compatible = "arm,cortex-a76-pmu";
+		interrupt-parent = <&gic>;
+		interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH &ppi_cluster1>;
+	};
+
+	psci {
+		compatible = "arm,psci-1.0";
+		method = "smc";
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupt-parent = <&gic>;
+		interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW 0>,
+			     <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW 0>,
+			     <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW 0>,
+			     <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW 0>;
+	};
+
+	soc {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		compatible = "simple-bus";
+		ranges;
+
+		gic: interrupt-controller@c000000 {
+			compatible = "arm,gic-v3";
+			#interrupt-cells = <4>;
+			#redistributor-regions = <1>;
+			interrupt-parent = <&gic>;
+			interrupt-controller;
+			reg = <0 0x0c000000 0 0x40000>,
+			      <0 0x0c040000 0 0x200000>;
+			interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH 0>;
+
+			ppi-partitions {
+				ppi_cluster0: interrupt-partition-0 {
+					affinity = <&cpu0 &cpu1 &cpu2 &cpu3 &cpu4 &cpu5>;
+				};
+
+				ppi_cluster1: interrupt-partition-1 {
+					affinity = <&cpu6 &cpu7>;
+				};
+			};
+		};
+
+		mcusys: syscon@c53a000 {
+			compatible = "mediatek,mt8186-mcusys", "syscon";
+			reg = <0 0xc53a000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
+		topckgen: syscon@10000000 {
+			compatible = "mediatek,mt8186-topckgen", "syscon";
+			reg = <0 0x10000000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
+		infracfg_ao: syscon@10001000 {
+			compatible = "mediatek,mt8186-infracfg_ao", "syscon";
+			reg = <0 0x10001000 0 0x1000>;
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+		};
+
+		pericfg: syscon@10003000 {
+			compatible = "mediatek,mt8186-pericfg", "syscon";
+			reg = <0 0x10003000 0 0x1000>;
+		};
+
+		pio: pinctrl@10005000 {
+			compatible = "mediatek,mt8186-pinctrl";
+			reg = <0 0x10005000 0 0x1000>,
+			      <0 0x10002000 0 0x0200>,
+			      <0 0x10002200 0 0x0200>,
+			      <0 0x10002400 0 0x0200>,
+			      <0 0x10002600 0 0x0200>,
+			      <0 0x10002a00 0 0x0200>,
+			      <0 0x10002c00 0 0x0200>,
+			      <0 0x1000b000 0 0x1000>;
+			reg-names = "iocfg0", "iocfg_lt", "iocfg_lm", "iocfg_lb",
+				    "iocfg_bl", "iocfg_rb", "iocfg_rt", "eint";
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&pio 0 0 185>;
+			interrupt-controller;
+			interrupts = <GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH 0>;
+			#interrupt-cells = <2>;
+		};
+
+		watchdog: watchdog@10007000 {
+			compatible = "mediatek,mt8186-wdt",
+				     "mediatek,mt6589-wdt";
+			mediatek,disable-extrst;
+			reg = <0 0x10007000 0 0x1000>;
+			#reset-cells = <1>;
+		};
+
+		apmixedsys: syscon@1000c000 {
+			compatible = "mediatek,mt8186-apmixedsys", "syscon";
+			reg = <0 0x1000c000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
+		pwrap: pwrap@1000d000 {
+			compatible = "mediatek,mt8186-pwrap", "syscon";
+			reg = <0 0x1000d000 0 0x1000>;
+			reg-names = "pwrap";
+			interrupts = <GIC_SPI 194 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&infracfg_ao CLK_INFRA_AO_PMIC_AP>,
+				 <&infracfg_ao CLK_INFRA_AO_PMIC_TMR>;
+			clock-names = "spi", "wrap";
+		};
+
+		systimer: timer@10017000 {
+			compatible = "mediatek,mt8186-timer",
+				     "mediatek,mt6765-timer";
+			reg = <0 0x10017000 0 0x1000>;
+			interrupts = <GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&clk13m>;
+		};
+
+		scp: scp@10500000 {
+			compatible = "mediatek,mt8186-scp";
+			reg = <0 0x10500000 0 0x40000>,
+			      <0 0x105c0000 0 0x19080>;
+			reg-names = "sram", "cfg";
+			interrupts = <GIC_SPI 205 IRQ_TYPE_LEVEL_HIGH 0>;
+		};
+
+		nor_flash: spi@11000000 {
+			compatible = "mediatek,mt8186-nor";
+			reg = <0 0x11000000 0 0x1000>;
+			clocks = <&topckgen CLK_TOP_SPINOR>,
+				 <&infracfg_ao CLK_INFRA_AO_SPINOR>,
+				 <&infracfg_ao CLK_INFRA_AO_FLASHIF_133M>,
+				 <&infracfg_ao CLK_INFRA_AO_FLASHIF_66M>;
+			clock-names = "spi", "sf", "axi", "axi_s";
+			assigned-clocks = <&topckgen CLK_TOP_SPINOR>;
+			assigned-clock-parents = <&topckgen CLK_TOP_UNIVPLL_D3_D8>;
+			interrupts = <GIC_SPI 293 IRQ_TYPE_LEVEL_HIGH 0>;
+			status = "disabled";
+		};
+
+		auxadc: adc@11001000 {
+			compatible = "mediatek,mt8186-auxadc", "mediatek,mt8173-auxadc";
+			reg = <0 0x11001000 0 0x1000>;
+			#io-channel-cells = <1>;
+			clocks = <&infracfg_ao CLK_INFRA_AO_AUXADC>;
+			clock-names = "main";
+		};
+
+		uart0: serial@11002000 {
+			compatible = "mediatek,mt8186-uart",
+				     "mediatek,mt6577-uart";
+			reg = <0 0x11002000 0 0x1000>;
+			interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&clk26m>, <&infracfg_ao CLK_INFRA_AO_UART0>;
+			clock-names = "baud", "bus";
+			status = "disabled";
+		};
+
+		uart1: serial@11003000 {
+			compatible = "mediatek,mt8186-uart",
+				     "mediatek,mt6577-uart";
+			reg = <0 0x11003000 0 0x1000>;
+			interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&clk26m>, <&infracfg_ao CLK_INFRA_AO_UART1>;
+			clock-names = "baud", "bus";
+			status = "disabled";
+		};
+
+		i2c0: i2c@11007000 {
+			compatible = "mediatek,mt8186-i2c";
+			reg = <0 0x11007000 0 0x1000>,
+			      <0 0x10200100 0 0x100>;
+			interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&imp_iic_wrap CLK_IMP_IIC_WRAP_AP_CLOCK_I2C0>,
+				 <&infracfg_ao CLK_INFRA_AO_AP_DMA>;
+			clock-names = "main", "dma";
+			clock-div = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i2c1: i2c@11008000 {
+			compatible = "mediatek,mt8186-i2c";
+			reg = <0 0x11008000 0 0x1000>,
+			      <0 0x10200200 0 0x100>;
+			interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&imp_iic_wrap CLK_IMP_IIC_WRAP_AP_CLOCK_I2C1>,
+				 <&infracfg_ao CLK_INFRA_AO_AP_DMA>;
+			clock-names = "main", "dma";
+			clock-div = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i2c2: i2c@11009000 {
+			compatible = "mediatek,mt8186-i2c";
+			reg = <0 0x11009000 0 0x1000>,
+			      <0 0x10200300 0 0x180>;
+			interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&imp_iic_wrap CLK_IMP_IIC_WRAP_AP_CLOCK_I2C2>,
+				 <&infracfg_ao CLK_INFRA_AO_AP_DMA>;
+			clock-names = "main", "dma";
+			clock-div = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i2c3: i2c@1100f000 {
+			compatible = "mediatek,mt8186-i2c";
+			reg = <0 0x1100f000 0 0x1000>,
+			      <0 0x10200480 0 0x100>;
+			interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&imp_iic_wrap CLK_IMP_IIC_WRAP_AP_CLOCK_I2C3>,
+				 <&infracfg_ao CLK_INFRA_AO_AP_DMA>;
+			clock-names = "main", "dma";
+			clock-div = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i2c4: i2c@11011000 {
+			compatible = "mediatek,mt8186-i2c";
+			reg = <0 0x11011000 0 0x1000>,
+			      <0 0x10200580 0 0x180>;
+			interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&imp_iic_wrap CLK_IMP_IIC_WRAP_AP_CLOCK_I2C4>,
+				 <&infracfg_ao CLK_INFRA_AO_AP_DMA>;
+			clock-names = "main", "dma";
+			clock-div = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i2c5: i2c@11016000 {
+			compatible = "mediatek,mt8186-i2c";
+			reg = <0 0x11016000 0 0x1000>,
+			      <0 0x10200700 0 0x100>;
+			interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&imp_iic_wrap CLK_IMP_IIC_WRAP_AP_CLOCK_I2C5>,
+				 <&infracfg_ao CLK_INFRA_AO_AP_DMA>;
+			clock-names = "main", "dma";
+			clock-div = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i2c6: i2c@1100d000 {
+			compatible = "mediatek,mt8186-i2c";
+			reg = <0 0x1100d000 0 0x1000>,
+			      <0 0x10200800 0 0x100>;
+			interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&imp_iic_wrap CLK_IMP_IIC_WRAP_AP_CLOCK_I2C6>,
+				 <&infracfg_ao CLK_INFRA_AO_AP_DMA>;
+			clock-names = "main", "dma";
+			clock-div = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i2c7: i2c@11004000 {
+			compatible = "mediatek,mt8186-i2c";
+			reg = <0 0x11004000 0 0x1000>,
+			      <0 0x10200900 0 0x180>;
+			interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&imp_iic_wrap CLK_IMP_IIC_WRAP_AP_CLOCK_I2C7>,
+				 <&infracfg_ao CLK_INFRA_AO_AP_DMA>;
+			clock-names = "main", "dma";
+			clock-div = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i2c8: i2c@11005000 {
+			compatible = "mediatek,mt8186-i2c";
+			reg = <0 0x11005000 0 0x1000>,
+			      <0 0x10200A80 0 0x180>;
+			interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&imp_iic_wrap CLK_IMP_IIC_WRAP_AP_CLOCK_I2C8>,
+				 <&infracfg_ao CLK_INFRA_AO_AP_DMA>;
+			clock-names = "main", "dma";
+			clock-div = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		spi0: spi@1100a000 {
+			compatible = "mediatek,mt8186-spi", "mediatek,mt6765-spi";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0 0x1100a000 0 0x1000>;
+			interrupts = <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&topckgen CLK_TOP_MAINPLL_D5>,
+				 <&topckgen CLK_TOP_SPI>,
+				 <&infracfg_ao CLK_INFRA_AO_SPI0>;
+			clock-names = "parent-clk", "sel-clk", "spi-clk";
+			status = "disabled";
+		};
+
+		pwm0: pwm@1100e000 {
+			compatible = "mediatek,mt8186-disp-pwm", "mediatek,mt8183-disp-pwm";
+			reg = <0 0x1100e000 0 0x1000>;
+			interrupts = <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH 0>;
+			#pwm-cells = <2>;
+			clocks = <&topckgen CLK_TOP_DISP_PWM>,
+				 <&infracfg_ao CLK_INFRA_AO_DISP_PWM>;
+			clock-names = "main", "mm";
+			status = "disabled";
+		};
+
+		spi1: spi@11010000 {
+			compatible = "mediatek,mt8186-spi", "mediatek,mt6765-spi";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0 0x11010000 0 0x1000>;
+			interrupts = <GIC_SPI 139 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&topckgen CLK_TOP_MAINPLL_D5>,
+				 <&topckgen CLK_TOP_SPI>,
+				 <&infracfg_ao CLK_INFRA_AO_SPI1>;
+			clock-names = "parent-clk", "sel-clk", "spi-clk";
+			status = "disabled";
+		};
+
+		spi2: spi@11012000 {
+			compatible = "mediatek,mt8186-spi", "mediatek,mt6765-spi";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0 0x11012000 0 0x1000>;
+			interrupts = <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&topckgen CLK_TOP_MAINPLL_D5>,
+				 <&topckgen CLK_TOP_SPI>,
+				 <&infracfg_ao CLK_INFRA_AO_SPI2>;
+			clock-names = "parent-clk", "sel-clk", "spi-clk";
+			status = "disabled";
+		};
+
+		spi3: spi@11013000 {
+			compatible = "mediatek,mt8186-spi", "mediatek,mt6765-spi";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0 0x11013000 0 0x1000>;
+			interrupts = <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&topckgen CLK_TOP_MAINPLL_D5>,
+				 <&topckgen CLK_TOP_SPI>,
+				 <&infracfg_ao CLK_INFRA_AO_SPI3>;
+			clock-names = "parent-clk", "sel-clk", "spi-clk";
+			status = "disabled";
+		};
+
+		spi4: spi@11014000 {
+			compatible = "mediatek,mt8186-spi", "mediatek,mt6765-spi";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0 0x11014000 0 0x1000>;
+			interrupts = <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&topckgen CLK_TOP_MAINPLL_D5>,
+				 <&topckgen CLK_TOP_SPI>,
+				 <&infracfg_ao CLK_INFRA_AO_SPI4>;
+			clock-names = "parent-clk", "sel-clk", "spi-clk";
+			status = "disabled";
+		};
+
+		spi5: spi@11015000 {
+			compatible = "mediatek,mt8186-spi", "mediatek,mt6765-spi";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0 0x11015000 0 0x1000>;
+			interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&topckgen CLK_TOP_MAINPLL_D5>,
+				 <&topckgen CLK_TOP_SPI>,
+				 <&infracfg_ao CLK_INFRA_AO_SPI5>;
+			clock-names = "parent-clk", "sel-clk", "spi-clk";
+			status = "disabled";
+		};
+
+		imp_iic_wrap: clock-controller@11017000 {
+			compatible = "mediatek,mt8186-imp_iic_wrap";
+			reg = <0 0x11017000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
+		uart2: serial@11018000 {
+			compatible = "mediatek,mt8186-uart",
+				     "mediatek,mt6577-uart";
+			reg = <0 0x11018000 0 0x1000>;
+			interrupts = <GIC_SPI 246 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&clk26m>, <&infracfg_ao CLK_INFRA_AO_UART2>;
+			clock-names = "baud", "bus";
+			status = "disabled";
+		};
+
+		i2c9: i2c@11019000 {
+			compatible = "mediatek,mt8186-i2c";
+			reg = <0 0x11019000 0 0x1000>,
+			      <0 0x10200c00 0 0x180>;
+			interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&imp_iic_wrap CLK_IMP_IIC_WRAP_AP_CLOCK_I2C9>,
+				 <&infracfg_ao CLK_INFRA_AO_AP_DMA>;
+			clock-names = "main", "dma";
+			clock-div = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		mmc0: mmc@11230000 {
+			compatible = "mediatek,mt8186-mmc",
+				     "mediatek,mt8183-mmc";
+			reg = <0 0x11230000 0 0x1000>,
+			      <0 0x11cd0000 0 0x1000>;
+			clocks = <&topckgen CLK_TOP_MSDC50_0>,
+				 <&infracfg_ao CLK_INFRA_AO_MSDC0>,
+				 <&infracfg_ao CLK_INFRA_AO_MSDC0_SRC>;
+			clock-names = "source", "hclk", "source_cg";
+			interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH 0>;
+			assigned-clocks = <&topckgen CLK_TOP_MSDC50_0>;
+			assigned-clock-parents = <&apmixedsys CLK_APMIXED_MSDCPLL>;
+			status = "disabled";
+		};
+
+		mmc1: mmc@11240000 {
+			compatible = "mediatek,mt8186-mmc",
+				     "mediatek,mt8183-mmc";
+			reg = <0 0x11240000 0 0x1000>,
+			      <0 0x11c90000 0 0x1000>;
+			clocks = <&topckgen CLK_TOP_MSDC30_1>,
+				 <&infracfg_ao CLK_INFRA_AO_MSDC1>,
+				 <&infracfg_ao CLK_INFRA_AO_MSDC1_SRC>;
+			clock-names = "source", "hclk", "source_cg";
+			interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH 0>;
+			assigned-clocks = <&topckgen CLK_TOP_MSDC30_1>;
+			assigned-clock-parents = <&topckgen CLK_TOP_MSDCPLL_D2>;
+			status = "disabled";
+		};
+
+		u3phy0: t-phy@11c80000 {
+			compatible = "mediatek,mt8186-tphy",
+				     "mediatek,generic-tphy-v2";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x0 0x11c80000 0x1000>;
+			status = "disabled";
+
+			u2port1: usb-phy@0 {
+				reg = <0x0 0x700>;
+				clocks = <&clk26m>;
+				clock-names = "ref";
+				#phy-cells = <1>;
+			};
+
+			u3port1: usb-phy@700 {
+				reg = <0x700 0x900>;
+				clocks = <&clk26m>;
+				clock-names = "ref";
+				#phy-cells = <1>;
+			};
+		};
+
+		u3phy1: t-phy@11ca0000 {
+			compatible = "mediatek,mt8186-tphy",
+				     "mediatek,generic-tphy-v2";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x0 0x11ca0000 0x1000>;
+			status = "disabled";
+
+			u2port0: usb-phy@0 {
+				reg = <0x0 0x700>;
+				clocks = <&clk26m>;
+				clock-names = "ref";
+				#phy-cells = <1>;
+				mediatek,discth = <0x8>;
+			};
+		};
+
+		efuse: efuse@11cb0000 {
+			compatible = "mediatek,mt8186-efuse", "mediatek,efuse";
+			reg = <0 0x11cb0000 0 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+		};
+
+		mipi_tx0: dsi-phy@11cc0000 {
+			compatible = "mediatek,mt8183-mipi-tx";
+			reg = <0 0x11cc0000 0 0x1000>;
+			clocks = <&clk26m>;
+			#clock-cells = <0>;
+			#phy-cells = <0>;
+			clock-output-names = "mipi_tx0_pll";
+			status = "disabled";
+		};
+
+		mfgsys: clock-controller@13000000 {
+			compatible = "mediatek,mt8186-mfgsys";
+			reg = <0 0x13000000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
+		mmsys: syscon@14000000 {
+			compatible = "mediatek,mt8186-mmsys", "syscon";
+			reg = <0 0x14000000 0 0x1000>;
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+		};
+
+		wpesys: clock-controller@14020000 {
+			compatible = "mediatek,mt8186-wpesys";
+			reg = <0 0x14020000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
+		imgsys1: clock-controller@15020000 {
+			compatible = "mediatek,mt8186-imgsys1";
+			reg = <0 0x15020000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
+		imgsys2: clock-controller@15820000 {
+			compatible = "mediatek,mt8186-imgsys2";
+			reg = <0 0x15820000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
+		vdecsys: clock-controller@1602f000 {
+			compatible = "mediatek,mt8186-vdecsys";
+			reg = <0 0x1602f000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
+		vencsys: clock-controller@17000000 {
+			compatible = "mediatek,mt8186-vencsys";
+			reg = <0 0x17000000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
+		camsys: clock-controller@1a000000 {
+			compatible = "mediatek,mt8186-camsys";
+			reg = <0 0x1a000000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
+		camsys_rawa: clock-controller@1a04f000 {
+			compatible = "mediatek,mt8186-camsys_rawa";
+			reg = <0 0x1a04f000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
+		camsys_rawb: clock-controller@1a06f000 {
+			compatible = "mediatek,mt8186-camsys_rawb";
+			reg = <0 0x1a06f000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
+		mdpsys: clock-controller@1b000000 {
+			compatible = "mediatek,mt8186-mdpsys";
+			reg = <0 0x1b000000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
+		ipesys: clock-controller@1c000000 {
+			compatible = "mediatek,mt8186-ipesys";
+			reg = <0 0x1c000000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+	};
+};
diff --git a/arch/arm64/boot/dts/mediatek/mt8192-asurada-hayato-r1.dts b/arch/arm64/boot/dts/mediatek/mt8192-asurada-hayato-r1.dts
new file mode 100644
index 000000000000..1e91491945f6
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt8192-asurada-hayato-r1.dts
@@ -0,0 +1,47 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright 2020 Google LLC
+ */
+/dts-v1/;
+#include "mt8192-asurada.dtsi"
+
+/ {
+	model = "Google Hayato rev1";
+	compatible = "google,hayato-rev1", "google,hayato", "mediatek,mt8192";
+};
+
+&keyboard_controller {
+	function-row-physmap = <
+		MATRIX_KEY(0x00, 0x02, 0)	/* T1 */
+		MATRIX_KEY(0x03, 0x02, 0)	/* T2 */
+		MATRIX_KEY(0x02, 0x02, 0)	/* T3 */
+		MATRIX_KEY(0x01, 0x02, 0)	/* T4 */
+		MATRIX_KEY(0x03, 0x04, 0)	/* T5 */
+		MATRIX_KEY(0x02, 0x04, 0)	/* T6 */
+		MATRIX_KEY(0x01, 0x04, 0)	/* T7 */
+		MATRIX_KEY(0x02, 0x09, 0)	/* T8 */
+		MATRIX_KEY(0x01, 0x09, 0)	/* T9 */
+		MATRIX_KEY(0x00, 0x04, 0)	/* T10 */
+	>;
+	linux,keymap = <
+		MATRIX_KEY(0x00, 0x02, KEY_BACK)
+		MATRIX_KEY(0x03, 0x02, KEY_FORWARD)
+		MATRIX_KEY(0x02, 0x02, KEY_REFRESH)
+		MATRIX_KEY(0x01, 0x02, KEY_FULL_SCREEN)
+		MATRIX_KEY(0x03, 0x04, KEY_SCALE)
+		MATRIX_KEY(0x02, 0x04, KEY_BRIGHTNESSDOWN)
+		MATRIX_KEY(0x01, 0x04, KEY_BRIGHTNESSUP)
+		MATRIX_KEY(0x02, 0x09, KEY_MUTE)
+		MATRIX_KEY(0x01, 0x09, KEY_VOLUMEDOWN)
+		MATRIX_KEY(0x00, 0x04, KEY_VOLUMEUP)
+
+		CROS_STD_MAIN_KEYMAP
+	>;
+};
+
+&touchscreen {
+	compatible = "hid-over-i2c";
+	post-power-on-delay-ms = <10>;
+	hid-descr-addr = <0x0001>;
+	vdd-supply = <&pp3300_u>;
+};
diff --git a/arch/arm64/boot/dts/mediatek/mt8192-asurada-spherion-r0.dts b/arch/arm64/boot/dts/mediatek/mt8192-asurada-spherion-r0.dts
new file mode 100644
index 000000000000..fa3d9573f37a
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt8192-asurada-spherion-r0.dts
@@ -0,0 +1,62 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright 2021 Google LLC
+ */
+/dts-v1/;
+#include "mt8192-asurada.dtsi"
+#include <dt-bindings/leds/common.h>
+
+/ {
+	model = "Google Spherion (rev0 - 3)";
+	compatible = "google,spherion-rev3", "google,spherion-rev2",
+		     "google,spherion-rev1", "google,spherion-rev0",
+		     "google,spherion", "mediatek,mt8192";
+
+	pwmleds {
+		compatible = "pwm-leds";
+
+		led {
+			function = LED_FUNCTION_KBD_BACKLIGHT;
+			color = <LED_COLOR_ID_WHITE>;
+			pwms = <&cros_ec_pwm 0>;
+			max-brightness = <1023>;
+		};
+	};
+};
+
+&cros_ec_pwm {
+	status = "okay";
+};
+
+&keyboard_controller {
+	function-row-physmap = <
+		MATRIX_KEY(0x00, 0x02, 0)	/* T1 */
+		MATRIX_KEY(0x03, 0x02, 0)	/* T2 */
+		MATRIX_KEY(0x02, 0x02, 0)	/* T3 */
+		MATRIX_KEY(0x01, 0x02, 0)	/* T4 */
+		MATRIX_KEY(0x03, 0x04, 0)	/* T5 */
+		MATRIX_KEY(0x02, 0x04, 0)	/* T6 */
+		MATRIX_KEY(0x01, 0x04, 0)	/* T7 */
+		MATRIX_KEY(0x02, 0x09, 0)	/* T8 */
+		MATRIX_KEY(0x01, 0x09, 0)	/* T9 */
+		MATRIX_KEY(0x00, 0x04, 0)	/* T10 */
+	>;
+	linux,keymap = <
+		MATRIX_KEY(0x00, 0x02, KEY_BACK)
+		MATRIX_KEY(0x03, 0x02, KEY_REFRESH)
+		MATRIX_KEY(0x02, 0x02, KEY_FULL_SCREEN)
+		MATRIX_KEY(0x01, 0x02, KEY_SCALE)
+		MATRIX_KEY(0x03, 0x04, KEY_SYSRQ)
+		MATRIX_KEY(0x02, 0x04, KEY_BRIGHTNESSDOWN)
+		MATRIX_KEY(0x01, 0x04, KEY_BRIGHTNESSUP)
+		MATRIX_KEY(0x02, 0x09, KEY_MUTE)
+		MATRIX_KEY(0x01, 0x09, KEY_VOLUMEDOWN)
+		MATRIX_KEY(0x00, 0x04, KEY_VOLUMEUP)
+
+		CROS_STD_MAIN_KEYMAP
+	>;
+};
+
+&touchscreen {
+	compatible = "elan,ekth3500";
+};
diff --git a/arch/arm64/boot/dts/mediatek/mt8192-asurada.dtsi b/arch/arm64/boot/dts/mediatek/mt8192-asurada.dtsi
new file mode 100644
index 000000000000..4b314435f8fd
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt8192-asurada.dtsi
@@ -0,0 +1,959 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright (C) 2020 MediaTek Inc.
+ * Author: Seiya Wang <seiya.wang@mediatek.com>
+ */
+/dts-v1/;
+#include "mt8192.dtsi"
+#include "mt6359.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/spmi/spmi.h>
+
+/ {
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@40000000 {
+		device_type = "memory";
+		reg = <0 0x40000000 0 0x80000000>;
+	};
+
+	/* system wide LDO 1.8V power rail */
+	pp1800_ldo_g: regulator-1v8-g {
+		compatible = "regulator-fixed";
+		regulator-name = "pp1800_ldo_g";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&pp3300_g>;
+	};
+
+	/* system wide switching 3.3V power rail */
+	pp3300_g: regulator-3v3-g {
+		compatible = "regulator-fixed";
+		regulator-name = "pp3300_g";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&ppvar_sys>;
+	};
+
+	/* system wide LDO 3.3V power rail */
+	pp3300_ldo_z: regulator-3v3-z {
+		compatible = "regulator-fixed";
+		regulator-name = "pp3300_ldo_z";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&ppvar_sys>;
+	};
+
+	/* separately switched 3.3V power rail */
+	pp3300_u: regulator-3v3-u {
+		compatible = "regulator-fixed";
+		regulator-name = "pp3300_u";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		/* enable pin wired to GPIO controlled by EC */
+		vin-supply = <&pp3300_g>;
+	};
+
+	pp3300_wlan: regulator-3v3-wlan {
+		compatible = "regulator-fixed";
+		regulator-name = "pp3300_wlan";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pp3300_wlan_pins>;
+		enable-active-high;
+		gpio = <&pio 143 GPIO_ACTIVE_HIGH>;
+	};
+
+	/* system wide switching 5.0V power rail */
+	pp5000_a: regulator-5v0-a {
+		compatible = "regulator-fixed";
+		regulator-name = "pp5000_a";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&ppvar_sys>;
+	};
+
+	/* system wide semi-regulated power rail from battery or USB */
+	ppvar_sys: regulator-var-sys {
+		compatible = "regulator-fixed";
+		regulator-name = "ppvar_sys";
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	reserved_memory: reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		scp_mem_reserved: scp@50000000 {
+			compatible = "shared-dma-pool";
+			reg = <0 0x50000000 0 0x2900000>;
+			no-map;
+		};
+
+		wifi_restricted_dma_region: wifi@c0000000 {
+			compatible = "restricted-dma-pool";
+			reg = <0 0xc0000000 0 0x4000000>;
+		};
+	};
+};
+
+&i2c0 {
+	status = "okay";
+
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins>;
+
+	touchscreen: touchscreen@10 {
+		reg = <0x10>;
+		interrupts-extended = <&pio 21 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&touchscreen_pins>;
+	};
+};
+
+&i2c1 {
+	status = "okay";
+
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+};
+
+&i2c2 {
+	status = "okay";
+
+	clock-frequency = <400000>;
+	clock-stretch-ns = <12600>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2_pins>;
+
+	trackpad@15 {
+		compatible = "elan,ekth3000";
+		reg = <0x15>;
+		interrupts-extended = <&pio 15 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&trackpad_pins>;
+		vcc-supply = <&pp3300_u>;
+		wakeup-source;
+	};
+};
+
+&i2c3 {
+	status = "okay";
+
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c3_pins>;
+};
+
+&i2c7 {
+	status = "okay";
+
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c7_pins>;
+};
+
+&mmc0 {
+	status = "okay";
+
+	pinctrl-names = "default", "state_uhs";
+	pinctrl-0 = <&mmc0_default_pins>;
+	pinctrl-1 = <&mmc0_uhs_pins>;
+	bus-width = <8>;
+	max-frequency = <200000000>;
+	vmmc-supply = <&mt6359_vemc_1_ldo_reg>;
+	vqmmc-supply = <&mt6359_vufs_ldo_reg>;
+	cap-mmc-highspeed;
+	mmc-hs200-1_8v;
+	mmc-hs400-1_8v;
+	supports-cqe;
+	cap-mmc-hw-reset;
+	mmc-hs400-enhanced-strobe;
+	hs400-ds-delay = <0x12814>;
+	no-sdio;
+	no-sd;
+	non-removable;
+};
+
+&mmc1 {
+	status = "okay";
+
+	pinctrl-names = "default", "state_uhs";
+	pinctrl-0 = <&mmc1_default_pins>;
+	pinctrl-1 = <&mmc1_uhs_pins>;
+	bus-width = <4>;
+	max-frequency = <200000000>;
+	cd-gpios = <&pio 17 GPIO_ACTIVE_LOW>;
+	vmmc-supply = <&mt6360_ldo5_reg>;
+	vqmmc-supply = <&mt6360_ldo3_reg>;
+	cap-sd-highspeed;
+	sd-uhs-sdr50;
+	sd-uhs-sdr104;
+	no-sdio;
+	no-mmc;
+};
+
+/* for CORE */
+&mt6359_vgpu11_buck_reg {
+	regulator-always-on;
+};
+
+&mt6359_vgpu11_sshub_buck_reg {
+	regulator-always-on;
+	regulator-min-microvolt = <575000>;
+	regulator-max-microvolt = <575000>;
+};
+
+&mt6359_vrf12_ldo_reg {
+	regulator-always-on;
+};
+
+&mt6359_vufs_ldo_reg {
+	regulator-always-on;
+};
+
+&mt6359codec {
+	mediatek,dmic-mode = <1>; /* one-wire */
+	mediatek,mic-type-0 = <2>; /* DMIC */
+	mediatek,mic-type-2 = <2>; /* DMIC */
+};
+
+&nor_flash {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&nor_flash_pins>;
+	assigned-clocks = <&topckgen CLK_TOP_SFLASH_SEL>;
+	assigned-clock-parents = <&topckgen CLK_TOP_UNIVPLL_D6_D8>;
+
+	flash@0 {
+		compatible = "winbond,w25q64jwm", "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <52000000>;
+		spi-rx-bus-width = <2>;
+		spi-tx-bus-width = <2>;
+	};
+};
+
+&pcie {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie_pins>;
+
+	pcie0: pcie@0,0 {
+		device_type = "pci";
+		reg = <0x0000 0 0 0 0>;
+		num-lanes = <1>;
+		bus-range = <0x1 0x1>;
+
+		#address-cells = <3>;
+		#size-cells = <2>;
+		ranges;
+
+		wifi: wifi@0,0 {
+			reg = <0x10000 0 0 0 0x100000>,
+			      <0x10000 0 0x100000 0 0x100000>;
+			memory-region = <&wifi_restricted_dma_region>;
+		};
+	};
+};
+
+&pio {
+	/* 220 lines */
+	gpio-line-names = "I2S_DP_LRCK",
+			  "IS_DP_BCLK",
+			  "I2S_DP_MCLK",
+			  "I2S_DP_DATAOUT",
+			  "SAR0_INT_ODL",
+			  "EC_AP_INT_ODL",
+			  "EDPBRDG_INT_ODL",
+			  "DPBRDG_INT_ODL",
+			  "DPBRDG_PWREN",
+			  "DPBRDG_RST_ODL",
+			  "I2S_HP_MCLK",
+			  "I2S_HP_BCK",
+			  "I2S_HP_LRCK",
+			  "I2S_HP_DATAIN",
+			  /*
+			   * AP_FLASH_WP_L is crossystem ABI. Schematics
+			   * call it AP_FLASH_WP_ODL.
+			   */
+			  "AP_FLASH_WP_L",
+			  "TRACKPAD_INT_ODL",
+			  "EC_AP_HPD_OD",
+			  "SD_CD_ODL",
+			  "HP_INT_ODL_ALC",
+			  "EN_PP1000_DPBRDG",
+			  "AP_GPIO20",
+			  "TOUCH_INT_L_1V8",
+			  "UART_BT_WAKE_ODL",
+			  "AP_GPIO23",
+			  "AP_SPI_FLASH_CS_L",
+			  "AP_SPI_FLASH_CLK",
+			  "EN_PP3300_DPBRDG_DX",
+			  "AP_SPI_FLASH_MOSI",
+			  "AP_SPI_FLASH_MISO",
+			  "I2S_HP_DATAOUT",
+			  "AP_GPIO30",
+			  "I2S_SPKR_MCLK",
+			  "I2S_SPKR_BCLK",
+			  "I2S_SPKR_LRCK",
+			  "I2S_SPKR_DATAIN",
+			  "I2S_SPKR_DATAOUT",
+			  "AP_SPI_H1_TPM_CLK",
+			  "AP_SPI_H1_TPM_CS_L",
+			  "AP_SPI_H1_TPM_MISO",
+			  "AP_SPI_H1_TPM_MOSI",
+			  "BL_PWM",
+			  "EDPBRDG_PWREN",
+			  "EDPBRDG_RST_ODL",
+			  "EN_PP3300_HUB",
+			  "HUB_RST_L",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "SD_CLK",
+			  "SD_CMD",
+			  "SD_DATA3",
+			  "SD_DATA0",
+			  "SD_DATA2",
+			  "SD_DATA1",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "PCIE_WAKE_ODL",
+			  "PCIE_RST_L",
+			  "PCIE_CLKREQ_ODL",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "SPMI_SCL",
+			  "SPMI_SDA",
+			  "AP_GOOD",
+			  "UART_DBG_TX_AP_RX",
+			  "UART_AP_TX_DBG_RX",
+			  "UART_AP_TX_BT_RX",
+			  "UART_BT_TX_AP_RX",
+			  "MIPI_DPI_D0_R",
+			  "MIPI_DPI_D1_R",
+			  "MIPI_DPI_D2_R",
+			  "MIPI_DPI_D3_R",
+			  "MIPI_DPI_D4_R",
+			  "MIPI_DPI_D5_R",
+			  "MIPI_DPI_D6_R",
+			  "MIPI_DPI_D7_R",
+			  "MIPI_DPI_D8_R",
+			  "MIPI_DPI_D9_R",
+			  "MIPI_DPI_D10_R",
+			  "",
+			  "",
+			  "MIPI_DPI_DE_R",
+			  "MIPI_DPI_D11_R",
+			  "MIPI_DPI_VSYNC_R",
+			  "MIPI_DPI_CLK_R",
+			  "MIPI_DPI_HSYNC_R",
+			  "PCM_BT_DATAIN",
+			  "PCM_BT_SYNC",
+			  "PCM_BT_DATAOUT",
+			  "PCM_BT_CLK",
+			  "AP_I2C_AUDIO_SCL",
+			  "AP_I2C_AUDIO_SDA",
+			  "SCP_I2C_SCL",
+			  "SCP_I2C_SDA",
+			  "AP_I2C_WLAN_SCL",
+			  "AP_I2C_WLAN_SDA",
+			  "AP_I2C_DPBRDG_SCL",
+			  "AP_I2C_DPBRDG_SDA",
+			  "EN_PP1800_DPBRDG_DX",
+			  "EN_PP3300_EDP_DX",
+			  "EN_PP1800_EDPBRDG_DX",
+			  "EN_PP1000_EDPBRDG",
+			  "SCP_JTAG0_TDO",
+			  "SCP_JTAG0_TDI",
+			  "SCP_JTAG0_TMS",
+			  "SCP_JTAG0_TCK",
+			  "SCP_JTAG0_TRSTN",
+			  "EN_PP3000_VMC_PMU",
+			  "EN_PP3300_DISPLAY_DX",
+			  "TOUCH_RST_L_1V8",
+			  "TOUCH_REPORT_DISABLE",
+			  "",
+			  "",
+			  "AP_I2C_TRACKPAD_SCL_1V8",
+			  "AP_I2C_TRACKPAD_SDA_1V8",
+			  "EN_PP3300_WLAN",
+			  "BT_KILL_L",
+			  "WIFI_KILL_L",
+			  "SET_VMC_VOLT_AT_1V8",
+			  "EN_SPK",
+			  "AP_WARM_RST_REQ",
+			  "",
+			  "",
+			  "EN_PP3000_SD_S3",
+			  "AP_EDP_BKLTEN",
+			  "",
+			  "",
+			  "",
+			  "AP_SPI_EC_CLK",
+			  "AP_SPI_EC_CS_L",
+			  "AP_SPI_EC_MISO",
+			  "AP_SPI_EC_MOSI",
+			  "AP_I2C_EDPBRDG_SCL",
+			  "AP_I2C_EDPBRDG_SDA",
+			  "MT6315_PROC_INT",
+			  "MT6315_GPU_INT",
+			  "UART_SERVO_TX_SCP_RX",
+			  "UART_SCP_TX_SERVO_RX",
+			  "BT_RTS_AP_CTS",
+			  "AP_RTS_BT_CTS",
+			  "UART_AP_WAKE_BT_ODL",
+			  "WLAN_ALERT_ODL",
+			  "EC_IN_RW_ODL",
+			  "H1_AP_INT_ODL",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "MSDC0_CMD",
+			  "MSDC0_DAT0",
+			  "MSDC0_DAT2",
+			  "MSDC0_DAT4",
+			  "MSDC0_DAT6",
+			  "MSDC0_DAT1",
+			  "MSDC0_DAT5",
+			  "MSDC0_DAT7",
+			  "MSDC0_DSL",
+			  "MSDC0_CLK",
+			  "MSDC0_DAT3",
+			  "MSDC0_RST_L",
+			  "SCP_VREQ_VAO",
+			  "AUD_DAT_MOSI2",
+			  "AUD_NLE_MOSI1",
+			  "AUD_NLE_MOSI0",
+			  "AUD_DAT_MISO2",
+			  "AP_I2C_SAR_SDA",
+			  "AP_I2C_SAR_SCL",
+			  "AP_I2C_PWR_SCL",
+			  "AP_I2C_PWR_SDA",
+			  "AP_I2C_TS_SCL_1V8",
+			  "AP_I2C_TS_SDA_1V8",
+			  "SRCLKENA0",
+			  "SRCLKENA1",
+			  "AP_EC_WATCHDOG_L",
+			  "PWRAP_SPI0_MI",
+			  "PWRAP_SPI0_CSN",
+			  "PWRAP_SPI0_MO",
+			  "PWRAP_SPI0_CK",
+			  "AP_RTC_CLK32K",
+			  "AUD_CLK_MOSI",
+			  "AUD_SYNC_MOSI",
+			  "AUD_DAT_MOSI0",
+			  "AUD_DAT_MOSI1",
+			  "AUD_DAT_MISO0",
+			  "AUD_DAT_MISO1";
+
+	cr50_int: cr50-irq-default-pins {
+		pins-gsc-ap-int-odl {
+			pinmux = <PINMUX_GPIO171__FUNC_GPIO171>;
+			input-enable;
+		};
+	};
+
+	cros_ec_int: cros-ec-irq-default-pins {
+		pins-ec-ap-int-odl {
+			pinmux = <PINMUX_GPIO5__FUNC_GPIO5>;
+			input-enable;
+			bias-pull-up;
+		};
+	};
+
+	i2c0_pins: i2c0-default-pins {
+		pins-bus {
+			pinmux = <PINMUX_GPIO204__FUNC_SCL0>,
+				 <PINMUX_GPIO205__FUNC_SDA0>;
+			bias-pull-up = <MTK_PULL_SET_RSEL_011>;
+			drive-strength-microamp = <1000>;
+		};
+	};
+
+	i2c1_pins: i2c1-default-pins {
+		pins-bus {
+			pinmux = <PINMUX_GPIO118__FUNC_SCL1>,
+				 <PINMUX_GPIO119__FUNC_SDA1>;
+			bias-pull-up = <MTK_PULL_SET_RSEL_011>;
+			drive-strength-microamp = <1000>;
+		};
+	};
+
+	i2c2_pins: i2c2-default-pins {
+		pins-bus {
+			pinmux = <PINMUX_GPIO141__FUNC_SCL2>,
+				 <PINMUX_GPIO142__FUNC_SDA2>;
+			bias-pull-up = <MTK_PULL_SET_RSEL_011>;
+		};
+	};
+
+	i2c3_pins: i2c3-default-pins {
+		pins-bus {
+			pinmux = <PINMUX_GPIO160__FUNC_SCL3>,
+				 <PINMUX_GPIO161__FUNC_SDA3>;
+			bias-disable;
+			drive-strength-microamp = <1000>;
+		};
+	};
+
+	i2c7_pins: i2c7-default-pins {
+		pins-bus {
+			pinmux = <PINMUX_GPIO124__FUNC_SCL7>,
+				 <PINMUX_GPIO125__FUNC_SDA7>;
+			bias-disable;
+			drive-strength-microamp = <1000>;
+		};
+	};
+
+	mmc0_default_pins: mmc0-default-pins {
+		pins-cmd-dat {
+			pinmux = <PINMUX_GPIO184__FUNC_MSDC0_DAT0>,
+				 <PINMUX_GPIO188__FUNC_MSDC0_DAT1>,
+				 <PINMUX_GPIO185__FUNC_MSDC0_DAT2>,
+				 <PINMUX_GPIO193__FUNC_MSDC0_DAT3>,
+				 <PINMUX_GPIO186__FUNC_MSDC0_DAT4>,
+				 <PINMUX_GPIO189__FUNC_MSDC0_DAT5>,
+				 <PINMUX_GPIO187__FUNC_MSDC0_DAT6>,
+				 <PINMUX_GPIO190__FUNC_MSDC0_DAT7>,
+				 <PINMUX_GPIO183__FUNC_MSDC0_CMD>;
+			input-enable;
+			drive-strength = <8>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+		};
+
+		pins-clk {
+			pinmux = <PINMUX_GPIO192__FUNC_MSDC0_CLK>;
+			drive-strength = <8>;
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
+		};
+
+		pins-rst {
+			pinmux = <PINMUX_GPIO194__FUNC_MSDC0_RSTB>;
+			drive-strength = <8>;
+			bias-pull-down = <MTK_PUPD_SET_R1R0_01>;
+		};
+	};
+
+	mmc0_uhs_pins: mmc0-uhs-pins {
+		pins-cmd-dat {
+			pinmux = <PINMUX_GPIO184__FUNC_MSDC0_DAT0>,
+				 <PINMUX_GPIO188__FUNC_MSDC0_DAT1>,
+				 <PINMUX_GPIO185__FUNC_MSDC0_DAT2>,
+				 <PINMUX_GPIO193__FUNC_MSDC0_DAT3>,
+				 <PINMUX_GPIO186__FUNC_MSDC0_DAT4>,
+				 <PINMUX_GPIO189__FUNC_MSDC0_DAT5>,
+				 <PINMUX_GPIO187__FUNC_MSDC0_DAT6>,
+				 <PINMUX_GPIO190__FUNC_MSDC0_DAT7>,
+				 <PINMUX_GPIO183__FUNC_MSDC0_CMD>;
+			input-enable;
+			drive-strength = <10>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+		};
+
+		pins-clk {
+			pinmux = <PINMUX_GPIO192__FUNC_MSDC0_CLK>;
+			drive-strength = <10>;
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
+		};
+
+		pins-rst {
+			pinmux = <PINMUX_GPIO194__FUNC_MSDC0_RSTB>;
+			drive-strength = <8>;
+			bias-pull-down = <MTK_PUPD_SET_R1R0_01>;
+		};
+
+		pins-ds {
+			pinmux = <PINMUX_GPIO191__FUNC_MSDC0_DSL>;
+			drive-strength = <10>;
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
+		};
+	};
+
+	mmc1_default_pins: mmc1-default-pins {
+		pins-cmd-dat {
+			pinmux = <PINMUX_GPIO54__FUNC_MSDC1_DAT0>,
+				 <PINMUX_GPIO56__FUNC_MSDC1_DAT1>,
+				 <PINMUX_GPIO55__FUNC_MSDC1_DAT2>,
+				 <PINMUX_GPIO53__FUNC_MSDC1_DAT3>,
+				 <PINMUX_GPIO52__FUNC_MSDC1_CMD>;
+			input-enable;
+			drive-strength = <8>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+		};
+
+		pins-clk {
+			pinmux = <PINMUX_GPIO51__FUNC_MSDC1_CLK>;
+			drive-strength = <8>;
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
+		};
+
+		pins-insert {
+			pinmux = <PINMUX_GPIO17__FUNC_GPIO17>;
+			input-enable;
+			bias-pull-up;
+		};
+	};
+
+	mmc1_uhs_pins: mmc1-uhs-pins {
+		pins-cmd-dat {
+			pinmux = <PINMUX_GPIO54__FUNC_MSDC1_DAT0>,
+				 <PINMUX_GPIO56__FUNC_MSDC1_DAT1>,
+				 <PINMUX_GPIO55__FUNC_MSDC1_DAT2>,
+				 <PINMUX_GPIO53__FUNC_MSDC1_DAT3>,
+				 <PINMUX_GPIO52__FUNC_MSDC1_CMD>;
+			input-enable;
+			drive-strength = <8>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+		};
+
+		pins-clk {
+			pinmux = <PINMUX_GPIO51__FUNC_MSDC1_CLK>;
+			input-enable;
+			drive-strength = <8>;
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
+		};
+	};
+
+	nor_flash_pins: nor-flash-default-pins {
+		pins-cs-io1 {
+			pinmux = <PINMUX_GPIO24__FUNC_SPINOR_CS>,
+				 <PINMUX_GPIO28__FUNC_SPINOR_IO1>;
+			input-enable;
+			bias-pull-up;
+			drive-strength = <10>;
+		};
+
+		pins-io0 {
+			pinmux = <PINMUX_GPIO27__FUNC_SPINOR_IO0>;
+			bias-pull-up;
+			drive-strength = <10>;
+		};
+
+		pins-clk {
+			pinmux = <PINMUX_GPIO25__FUNC_SPINOR_CK>;
+			input-enable;
+			bias-pull-up;
+			drive-strength = <10>;
+		};
+	};
+
+	pcie_pins: pcie-default-pins {
+		pins-pcie-wake {
+			pinmux = <PINMUX_GPIO63__FUNC_PCIE_WAKE_N>;
+			bias-pull-up;
+		};
+
+		pins-pcie-pereset {
+			pinmux = <PINMUX_GPIO64__FUNC_PCIE_PERESET_N>;
+		};
+
+		pins-pcie-clkreq {
+			pinmux = <PINMUX_GPIO65__FUNC_PCIE_CLKREQ_N>;
+			bias-pull-up;
+		};
+
+		pins-wifi-kill {
+			pinmux = <PINMUX_GPIO145__FUNC_GPIO145>; /* WIFI_KILL_L */
+			output-high;
+		};
+	};
+
+	pp3300_wlan_pins: pp3300-wlan-pins {
+		pins-pcie-en-pp3300-wlan {
+			pinmux = <PINMUX_GPIO143__FUNC_GPIO143>;
+			output-high;
+		};
+	};
+
+	scp_pins: scp-pins {
+		pins-vreq-vao {
+			pinmux = <PINMUX_GPIO195__FUNC_SCP_VREQ_VAO>;
+		};
+	};
+
+	spi1_pins: spi1-default-pins {
+		pins-cs-mosi-clk {
+			pinmux = <PINMUX_GPIO157__FUNC_SPI1_A_CSB>,
+				 <PINMUX_GPIO159__FUNC_SPI1_A_MO>,
+				 <PINMUX_GPIO156__FUNC_SPI1_A_CLK>;
+			bias-disable;
+		};
+
+		pins-miso {
+			pinmux = <PINMUX_GPIO158__FUNC_SPI1_A_MI>;
+			bias-pull-down;
+		};
+	};
+
+	spi5_pins: spi5-default-pins {
+		pins-bus {
+			pinmux = <PINMUX_GPIO38__FUNC_SPI5_A_MI>,
+				 <PINMUX_GPIO37__FUNC_GPIO37>,
+				 <PINMUX_GPIO39__FUNC_SPI5_A_MO>,
+				 <PINMUX_GPIO36__FUNC_SPI5_A_CLK>;
+			bias-disable;
+		};
+	};
+
+	trackpad_pins: trackpad-default-pins {
+		pins-int-n {
+			pinmux = <PINMUX_GPIO15__FUNC_GPIO15>;
+			input-enable;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_11>;
+		};
+	};
+
+	touchscreen_pins: touchscreen-default-pins {
+		pins-irq {
+			pinmux = <PINMUX_GPIO21__FUNC_GPIO21>;
+			input-enable;
+			bias-pull-up;
+		};
+
+		pins-reset {
+			pinmux = <PINMUX_GPIO137__FUNC_GPIO137>;
+			output-high;
+		};
+
+		pins-report-sw {
+			pinmux = <PINMUX_GPIO138__FUNC_GPIO138>;
+			output-low;
+		};
+	};
+};
+
+&pmic {
+	interrupts-extended = <&pio 214 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&scp {
+	status = "okay";
+
+	firmware-name = "mediatek/mt8192/scp.img";
+	memory-region = <&scp_mem_reserved>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&scp_pins>;
+
+	cros-ec {
+		compatible = "google,cros-ec-rpmsg";
+		mediatek,rpmsg-name = "cros-ec-rpmsg";
+	};
+};
+
+&spi1 {
+	status = "okay";
+
+	mediatek,pad-select = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi1_pins>;
+
+	cros_ec: ec@0 {
+		compatible = "google,cros-ec-spi";
+		reg = <0>;
+		interrupts-extended = <&pio 5 IRQ_TYPE_LEVEL_LOW>;
+		spi-max-frequency = <3000000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&cros_ec_int>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		base_detection: cbas {
+			compatible = "google,cros-cbas";
+		};
+
+		cros_ec_pwm: pwm {
+			compatible = "google,cros-ec-pwm";
+			#pwm-cells = <1>;
+
+			status = "disabled";
+		};
+
+		i2c_tunnel: i2c-tunnel {
+			compatible = "google,cros-ec-i2c-tunnel";
+			google,remote-bus = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		mt6360_ldo3_reg: regulator@0 {
+			compatible = "google,cros-ec-regulator";
+			reg = <0>;
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <3300000>;
+		};
+
+		mt6360_ldo5_reg: regulator@1 {
+			compatible = "google,cros-ec-regulator";
+			reg = <1>;
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+		};
+
+		typec {
+			compatible = "google,cros-ec-typec";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			usb_c0: connector@0 {
+				compatible = "usb-c-connector";
+				reg = <0>;
+				label = "left";
+				power-role = "dual";
+				data-role = "host";
+				try-power-role = "source";
+			};
+
+			usb_c1: connector@1 {
+				compatible = "usb-c-connector";
+				reg = <1>;
+				label = "right";
+				power-role = "dual";
+				data-role = "host";
+				try-power-role = "source";
+			};
+		};
+	};
+};
+
+&spi5 {
+	status = "okay";
+
+	cs-gpios = <&pio 37 GPIO_ACTIVE_LOW>;
+	mediatek,pad-select = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi5_pins>;
+
+	cr50@0 {
+		compatible = "google,cr50";
+		reg = <0>;
+		interrupts-extended = <&pio 171 IRQ_TYPE_EDGE_RISING>;
+		spi-max-frequency = <1000000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&cr50_int>;
+	};
+};
+
+&spmi {
+	#address-cells = <2>;
+	#size-cells = <0>;
+
+	mt6315_6: pmic@6 {
+		compatible = "mediatek,mt6315-regulator";
+		reg = <0x6 SPMI_USID>;
+
+		regulators {
+			mt6315_6_vbuck1: vbuck1 {
+				regulator-compatible = "vbuck1";
+				regulator-name = "Vbcpu";
+				regulator-min-microvolt = <300000>;
+				regulator-max-microvolt = <1193750>;
+				regulator-enable-ramp-delay = <256>;
+				regulator-allowed-modes = <0 1 2>;
+				regulator-always-on;
+			};
+
+			mt6315_6_vbuck3: vbuck3 {
+				regulator-compatible = "vbuck3";
+				regulator-name = "Vlcpu";
+				regulator-min-microvolt = <300000>;
+				regulator-max-microvolt = <1193750>;
+				regulator-enable-ramp-delay = <256>;
+				regulator-allowed-modes = <0 1 2>;
+				regulator-always-on;
+			};
+		};
+	};
+
+	mt6315_7: pmic@7 {
+		compatible = "mediatek,mt6315-regulator";
+		reg = <0x7 SPMI_USID>;
+
+		regulators {
+			mt6315_7_vbuck1: vbuck1 {
+				regulator-compatible = "vbuck1";
+				regulator-name = "Vgpu";
+				regulator-min-microvolt = <606250>;
+				regulator-max-microvolt = <1193750>;
+				regulator-enable-ramp-delay = <256>;
+				regulator-allowed-modes = <0 1 2>;
+			};
+		};
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&xhci {
+	status = "okay";
+
+	wakeup-source;
+	vusb33-supply = <&pp3300_g>;
+	vbus-supply = <&pp5000_a>;
+};
+
+#include <arm/cros-ec-keyboard.dtsi>
+#include <arm/cros-ec-sbs.dtsi>
diff --git a/arch/arm64/boot/dts/mediatek/mt8192-evb.dts b/arch/arm64/boot/dts/mediatek/mt8192-evb.dts
index 0205837fa698..808be492e970 100644
--- a/arch/arm64/boot/dts/mediatek/mt8192-evb.dts
+++ b/arch/arm64/boot/dts/mediatek/mt8192-evb.dts
@@ -5,6 +5,7 @@
  */
 /dts-v1/;
 #include "mt8192.dtsi"
+#include "mt6359.dtsi"
 
 / {
 	model = "MediaTek MT8192 evaluation board";
diff --git a/arch/arm64/boot/dts/mediatek/mt8192.dtsi b/arch/arm64/boot/dts/mediatek/mt8192.dtsi
index c7c7d4e017ae..6b20376191a7 100644
--- a/arch/arm64/boot/dts/mediatek/mt8192.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt8192.dtsi
@@ -6,9 +6,14 @@
 
 /dts-v1/;
 #include <dt-bindings/clock/mt8192-clk.h>
+#include <dt-bindings/gce/mt8192-gce.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/memory/mt8192-larb-port.h>
 #include <dt-bindings/pinctrl/mt8192-pinfunc.h>
+#include <dt-bindings/phy/phy.h>
+#include <dt-bindings/power/mt8192-power.h>
+#include <dt-bindings/reset/mt8192-resets.h>
 
 / {
 	compatible = "mediatek,mt8192";
@@ -16,6 +21,14 @@
 	#address-cells = <2>;
 	#size-cells = <2>;
 
+	aliases {
+		ovl0 = &ovl0;
+		ovl-2l0 = &ovl_2l0;
+		ovl-2l2 = &ovl_2l2;
+		rdma0 = &rdma0;
+		rdma4 = &rdma4;
+	};
+
 	clk26m: oscillator0 {
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
@@ -40,7 +53,7 @@
 			reg = <0x000>;
 			enable-method = "psci";
 			clock-frequency = <1701000000>;
-			cpu-idle-states = <&cpuoff_l &clusteroff_l>;
+			cpu-idle-states = <&cpu_sleep_l &cluster_sleep_l>;
 			next-level-cache = <&l2_0>;
 			capacity-dmips-mhz = <530>;
 		};
@@ -51,7 +64,7 @@
 			reg = <0x100>;
 			enable-method = "psci";
 			clock-frequency = <1701000000>;
-			cpu-idle-states = <&cpuoff_l &clusteroff_l>;
+			cpu-idle-states = <&cpu_sleep_l &cluster_sleep_l>;
 			next-level-cache = <&l2_0>;
 			capacity-dmips-mhz = <530>;
 		};
@@ -62,7 +75,7 @@
 			reg = <0x200>;
 			enable-method = "psci";
 			clock-frequency = <1701000000>;
-			cpu-idle-states = <&cpuoff_l &clusteroff_l>;
+			cpu-idle-states = <&cpu_sleep_l &cluster_sleep_l>;
 			next-level-cache = <&l2_0>;
 			capacity-dmips-mhz = <530>;
 		};
@@ -73,7 +86,7 @@
 			reg = <0x300>;
 			enable-method = "psci";
 			clock-frequency = <1701000000>;
-			cpu-idle-states = <&cpuoff_l &clusteroff_l>;
+			cpu-idle-states = <&cpu_sleep_l &cluster_sleep_l>;
 			next-level-cache = <&l2_0>;
 			capacity-dmips-mhz = <530>;
 		};
@@ -84,7 +97,7 @@
 			reg = <0x400>;
 			enable-method = "psci";
 			clock-frequency = <2171000000>;
-			cpu-idle-states = <&cpuoff_b &clusteroff_b>;
+			cpu-idle-states = <&cpu_sleep_b &cluster_sleep_b>;
 			next-level-cache = <&l2_1>;
 			capacity-dmips-mhz = <1024>;
 		};
@@ -95,7 +108,7 @@
 			reg = <0x500>;
 			enable-method = "psci";
 			clock-frequency = <2171000000>;
-			cpu-idle-states = <&cpuoff_b &clusteroff_b>;
+			cpu-idle-states = <&cpu_sleep_b &cluster_sleep_b>;
 			next-level-cache = <&l2_1>;
 			capacity-dmips-mhz = <1024>;
 		};
@@ -106,7 +119,7 @@
 			reg = <0x600>;
 			enable-method = "psci";
 			clock-frequency = <2171000000>;
-			cpu-idle-states = <&cpuoff_b &clusteroff_b>;
+			cpu-idle-states = <&cpu_sleep_b &cluster_sleep_b>;
 			next-level-cache = <&l2_1>;
 			capacity-dmips-mhz = <1024>;
 		};
@@ -117,7 +130,7 @@
 			reg = <0x700>;
 			enable-method = "psci";
 			clock-frequency = <2171000000>;
-			cpu-idle-states = <&cpuoff_b &clusteroff_b>;
+			cpu-idle-states = <&cpu_sleep_b &cluster_sleep_b>;
 			next-level-cache = <&l2_1>;
 			capacity-dmips-mhz = <1024>;
 		};
@@ -169,8 +182,8 @@
 		};
 
 		idle-states {
-			entry-method = "arm,psci";
-			cpuoff_l: cpuoff_l {
+			entry-method = "psci";
+			cpu_sleep_l: cpu-sleep-l {
 				compatible = "arm,idle-state";
 				arm,psci-suspend-param = <0x00010001>;
 				local-timer-stop;
@@ -178,7 +191,7 @@
 				exit-latency-us = <140>;
 				min-residency-us = <780>;
 			};
-			cpuoff_b: cpuoff_b {
+			cpu_sleep_b: cpu-sleep-b {
 				compatible = "arm,idle-state";
 				arm,psci-suspend-param = <0x00010001>;
 				local-timer-stop;
@@ -186,7 +199,7 @@
 				exit-latency-us = <145>;
 				min-residency-us = <720>;
 			};
-			clusteroff_l: clusteroff_l {
+			cluster_sleep_l: cluster-sleep-l {
 				compatible = "arm,idle-state";
 				arm,psci-suspend-param = <0x01010002>;
 				local-timer-stop;
@@ -194,7 +207,7 @@
 				exit-latency-us = <155>;
 				min-residency-us = <860>;
 			};
-			clusteroff_b: clusteroff_b {
+			cluster_sleep_b: cluster-sleep-b {
 				compatible = "arm,idle-state";
 				arm,psci-suspend-param = <0x01010002>;
 				local-timer-stop;
@@ -268,6 +281,7 @@
 			compatible = "mediatek,mt8192-infracfg", "syscon";
 			reg = <0 0x10001000 0 0x1000>;
 			#clock-cells = <1>;
+			#reset-cells = <1>;
 		};
 
 		pericfg: syscon@10003000 {
@@ -301,6 +315,211 @@
 			#interrupt-cells = <2>;
 		};
 
+		scpsys: syscon@10006000 {
+			compatible = "mediatek,mt8192-scpsys", "syscon", "simple-mfd";
+			reg = <0 0x10006000 0 0x1000>;
+
+			/* System Power Manager */
+			spm: power-controller {
+				compatible = "mediatek,mt8192-power-controller";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				#power-domain-cells = <1>;
+
+				/* power domain of the SoC */
+				power-domain@MT8192_POWER_DOMAIN_AUDIO {
+					reg = <MT8192_POWER_DOMAIN_AUDIO>;
+					clocks = <&topckgen CLK_TOP_AUD_INTBUS_SEL>,
+						 <&infracfg CLK_INFRA_AUDIO_26M_B>,
+						 <&infracfg CLK_INFRA_AUDIO>;
+					clock-names = "audio", "audio1", "audio2";
+					mediatek,infracfg = <&infracfg>;
+					#power-domain-cells = <0>;
+				};
+
+				power-domain@MT8192_POWER_DOMAIN_CONN {
+					reg = <MT8192_POWER_DOMAIN_CONN>;
+					clocks = <&infracfg CLK_INFRA_PMIC_CONN>;
+					clock-names = "conn";
+					mediatek,infracfg = <&infracfg>;
+					#power-domain-cells = <0>;
+				};
+
+				power-domain@MT8192_POWER_DOMAIN_MFG0 {
+					reg = <MT8192_POWER_DOMAIN_MFG0>;
+					clocks = <&topckgen CLK_TOP_MFG_PLL_SEL>;
+					clock-names = "mfg";
+					#address-cells = <1>;
+					#size-cells = <0>;
+					#power-domain-cells = <1>;
+
+					power-domain@MT8192_POWER_DOMAIN_MFG1 {
+						reg = <MT8192_POWER_DOMAIN_MFG1>;
+						mediatek,infracfg = <&infracfg>;
+						#address-cells = <1>;
+						#size-cells = <0>;
+						#power-domain-cells = <1>;
+
+						power-domain@MT8192_POWER_DOMAIN_MFG2 {
+							reg = <MT8192_POWER_DOMAIN_MFG2>;
+							#power-domain-cells = <0>;
+						};
+
+						power-domain@MT8192_POWER_DOMAIN_MFG3 {
+							reg = <MT8192_POWER_DOMAIN_MFG3>;
+							#power-domain-cells = <0>;
+						};
+
+						power-domain@MT8192_POWER_DOMAIN_MFG4 {
+							reg = <MT8192_POWER_DOMAIN_MFG4>;
+							#power-domain-cells = <0>;
+						};
+
+						power-domain@MT8192_POWER_DOMAIN_MFG5 {
+							reg = <MT8192_POWER_DOMAIN_MFG5>;
+							#power-domain-cells = <0>;
+						};
+
+						power-domain@MT8192_POWER_DOMAIN_MFG6 {
+							reg = <MT8192_POWER_DOMAIN_MFG6>;
+							#power-domain-cells = <0>;
+						};
+					};
+				};
+
+				power-domain@MT8192_POWER_DOMAIN_DISP {
+					reg = <MT8192_POWER_DOMAIN_DISP>;
+					clocks = <&topckgen CLK_TOP_DISP_SEL>,
+						 <&mmsys CLK_MM_SMI_INFRA>,
+						 <&mmsys CLK_MM_SMI_COMMON>,
+						 <&mmsys CLK_MM_SMI_GALS>,
+						 <&mmsys CLK_MM_SMI_IOMMU>;
+					clock-names = "disp", "disp-0", "disp-1", "disp-2",
+						      "disp-3";
+					mediatek,infracfg = <&infracfg>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+					#power-domain-cells = <1>;
+
+					power-domain@MT8192_POWER_DOMAIN_IPE {
+						reg = <MT8192_POWER_DOMAIN_IPE>;
+						clocks = <&topckgen CLK_TOP_IPE_SEL>,
+							 <&ipesys CLK_IPE_LARB19>,
+							 <&ipesys CLK_IPE_LARB20>,
+							 <&ipesys CLK_IPE_SMI_SUBCOM>,
+							 <&ipesys CLK_IPE_GALS>;
+						clock-names = "ipe", "ipe-0", "ipe-1", "ipe-2",
+							      "ipe-3";
+						mediatek,infracfg = <&infracfg>;
+						#power-domain-cells = <0>;
+					};
+
+					power-domain@MT8192_POWER_DOMAIN_ISP {
+						reg = <MT8192_POWER_DOMAIN_ISP>;
+						clocks = <&topckgen CLK_TOP_IMG1_SEL>,
+							 <&imgsys CLK_IMG_LARB9>,
+							 <&imgsys CLK_IMG_GALS>;
+						clock-names = "isp", "isp-0", "isp-1";
+						mediatek,infracfg = <&infracfg>;
+						#power-domain-cells = <0>;
+					};
+
+					power-domain@MT8192_POWER_DOMAIN_ISP2 {
+						reg = <MT8192_POWER_DOMAIN_ISP2>;
+						clocks = <&topckgen CLK_TOP_IMG2_SEL>,
+							 <&imgsys2 CLK_IMG2_LARB11>,
+							 <&imgsys2 CLK_IMG2_GALS>;
+						clock-names = "isp2", "isp2-0", "isp2-1";
+						mediatek,infracfg = <&infracfg>;
+						#power-domain-cells = <0>;
+					};
+
+					power-domain@MT8192_POWER_DOMAIN_MDP {
+						reg = <MT8192_POWER_DOMAIN_MDP>;
+						clocks = <&topckgen CLK_TOP_MDP_SEL>,
+							 <&mdpsys CLK_MDP_SMI0>;
+						clock-names = "mdp", "mdp-0";
+						mediatek,infracfg = <&infracfg>;
+						#power-domain-cells = <0>;
+					};
+
+					power-domain@MT8192_POWER_DOMAIN_VENC {
+						reg = <MT8192_POWER_DOMAIN_VENC>;
+						clocks = <&topckgen CLK_TOP_VENC_SEL>,
+							 <&vencsys CLK_VENC_SET1_VENC>;
+						clock-names = "venc", "venc-0";
+						mediatek,infracfg = <&infracfg>;
+						#power-domain-cells = <0>;
+					};
+
+					power-domain@MT8192_POWER_DOMAIN_VDEC {
+						reg = <MT8192_POWER_DOMAIN_VDEC>;
+						clocks = <&topckgen CLK_TOP_VDEC_SEL>,
+							 <&vdecsys_soc CLK_VDEC_SOC_VDEC>,
+							 <&vdecsys_soc CLK_VDEC_SOC_LAT>,
+							 <&vdecsys_soc CLK_VDEC_SOC_LARB1>;
+						clock-names = "vdec", "vdec-0", "vdec-1", "vdec-2";
+						mediatek,infracfg = <&infracfg>;
+						#address-cells = <1>;
+						#size-cells = <0>;
+						#power-domain-cells = <1>;
+
+						power-domain@MT8192_POWER_DOMAIN_VDEC2 {
+							reg = <MT8192_POWER_DOMAIN_VDEC2>;
+							clocks = <&vdecsys CLK_VDEC_VDEC>,
+								 <&vdecsys CLK_VDEC_LAT>,
+								 <&vdecsys CLK_VDEC_LARB1>;
+							clock-names = "vdec2-0", "vdec2-1",
+								      "vdec2-2";
+							#power-domain-cells = <0>;
+						};
+					};
+
+					power-domain@MT8192_POWER_DOMAIN_CAM {
+						reg = <MT8192_POWER_DOMAIN_CAM>;
+						clocks = <&topckgen CLK_TOP_CAM_SEL>,
+							 <&camsys CLK_CAM_LARB13>,
+							 <&camsys CLK_CAM_LARB14>,
+							 <&camsys CLK_CAM_CCU_GALS>,
+							 <&camsys CLK_CAM_CAM2MM_GALS>;
+						clock-names = "cam", "cam-0", "cam-1", "cam-2",
+							      "cam-3";
+						mediatek,infracfg = <&infracfg>;
+						#address-cells = <1>;
+						#size-cells = <0>;
+						#power-domain-cells = <1>;
+
+						power-domain@MT8192_POWER_DOMAIN_CAM_RAWA {
+							reg = <MT8192_POWER_DOMAIN_CAM_RAWA>;
+							clocks = <&camsys_rawa CLK_CAM_RAWA_LARBX>;
+							clock-names = "cam_rawa-0";
+							#power-domain-cells = <0>;
+						};
+
+						power-domain@MT8192_POWER_DOMAIN_CAM_RAWB {
+							reg = <MT8192_POWER_DOMAIN_CAM_RAWB>;
+							clocks = <&camsys_rawb CLK_CAM_RAWB_LARBX>;
+							clock-names = "cam_rawb-0";
+							#power-domain-cells = <0>;
+						};
+
+						power-domain@MT8192_POWER_DOMAIN_CAM_RAWC {
+							reg = <MT8192_POWER_DOMAIN_CAM_RAWC>;
+							clocks = <&camsys_rawc CLK_CAM_RAWC_LARBX>;
+							clock-names = "cam_rawc-0";
+							#power-domain-cells = <0>;
+						};
+					};
+				};
+			};
+		};
+
+		watchdog: watchdog@10007000 {
+			compatible = "mediatek,mt8192-wdt";
+			reg = <0 0x10007000 0 0x100>;
+			#reset-cells = <1>;
+		};
+
 		apmixedsys: syscon@1000c000 {
 			compatible = "mediatek,mt8192-apmixedsys", "syscon";
 			reg = <0 0x1000c000 0 0x1000>;
@@ -312,10 +531,46 @@
 				     "mediatek,mt6765-timer";
 			reg = <0 0x10017000 0 0x1000>;
 			interrupts = <GIC_SPI 233 IRQ_TYPE_LEVEL_HIGH 0>;
-			clocks = <&clk26m>;
+			clocks = <&topckgen CLK_TOP_CSW_F26M_D2>;
 			clock-names = "clk13m";
 		};
 
+		pwrap: pwrap@10026000 {
+			compatible = "mediatek,mt6873-pwrap";
+			reg = <0 0x10026000 0 0x1000>;
+			reg-names = "pwrap";
+			interrupts = <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&infracfg CLK_INFRA_PMIC_AP>,
+				 <&infracfg CLK_INFRA_PMIC_TMR>;
+			clock-names = "spi", "wrap";
+			assigned-clocks = <&topckgen CLK_TOP_PWRAP_ULPOSC_SEL>;
+			assigned-clock-parents = <&topckgen CLK_TOP_OSC_D10>;
+		};
+
+		spmi: spmi@10027000 {
+			compatible = "mediatek,mt6873-spmi";
+			reg = <0 0x10027000 0 0x000e00>,
+			      <0 0x10029000 0 0x000100>;
+			reg-names = "pmif", "spmimst";
+			clocks = <&infracfg CLK_INFRA_PMIC_AP>,
+				 <&infracfg CLK_INFRA_PMIC_TMR>,
+				 <&topckgen CLK_TOP_SPMI_MST_SEL>;
+			clock-names = "pmif_sys_ck",
+				      "pmif_tmr_ck",
+				      "spmimst_clk_mux";
+			assigned-clocks = <&topckgen CLK_TOP_PWRAP_ULPOSC_SEL>;
+			assigned-clock-parents = <&topckgen CLK_TOP_OSC_D10>;
+		};
+
+		gce: mailbox@10228000 {
+			compatible = "mediatek,mt8192-gce";
+			reg = <0 0x10228000 0 0x4000>;
+			interrupts = <GIC_SPI 203 IRQ_TYPE_LEVEL_HIGH 0>;
+			#mbox-cells = <2>;
+			clocks = <&infracfg CLK_INFRA_GCE>;
+			clock-names = "gce";
+		};
+
 		scp_adsp: clock-controller@10720000 {
 			compatible = "mediatek,mt8192-scp_adsp";
 			reg = <0 0x10720000 0 0x1000>;
@@ -327,7 +582,7 @@
 				     "mediatek,mt6577-uart";
 			reg = <0 0x11002000 0 0x1000>;
 			interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH 0>;
-			clocks = <&clk26m>, <&clk26m>;
+			clocks = <&clk26m>, <&infracfg CLK_INFRA_UART0>;
 			clock-names = "baud", "bus";
 			status = "disabled";
 		};
@@ -337,7 +592,7 @@
 				     "mediatek,mt6577-uart";
 			reg = <0 0x11003000 0 0x1000>;
 			interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH 0>;
-			clocks = <&clk26m>, <&clk26m>;
+			clocks = <&clk26m>, <&infracfg CLK_INFRA_UART1>;
 			clock-names = "baud", "bus";
 			status = "disabled";
 		};
@@ -355,13 +610,24 @@
 			#size-cells = <0>;
 			reg = <0 0x1100a000 0 0x1000>;
 			interrupts = <GIC_SPI 159 IRQ_TYPE_LEVEL_HIGH 0>;
-			clocks = <&clk26m>,
-				 <&clk26m>,
-				 <&clk26m>;
+			clocks = <&topckgen CLK_TOP_MAINPLL_D5_D4>,
+				 <&topckgen CLK_TOP_SPI_SEL>,
+				 <&infracfg CLK_INFRA_SPI0>;
 			clock-names = "parent-clk", "sel-clk", "spi-clk";
 			status = "disabled";
 		};
 
+		pwm0: pwm@1100e000 {
+			compatible = "mediatek,mt8183-disp-pwm";
+			reg = <0 0x1100e000 0 0x1000>;
+			interrupts = <GIC_SPI 171 IRQ_TYPE_LEVEL_HIGH 0>;
+			#pwm-cells = <2>;
+			clocks = <&topckgen CLK_TOP_DISP_PWM_SEL>,
+				 <&infracfg CLK_INFRA_DISP_PWM>;
+			clock-names = "main", "mm";
+			status = "disabled";
+		};
+
 		spi1: spi@11010000 {
 			compatible = "mediatek,mt8192-spi",
 				     "mediatek,mt6765-spi";
@@ -369,9 +635,9 @@
 			#size-cells = <0>;
 			reg = <0 0x11010000 0 0x1000>;
 			interrupts = <GIC_SPI 160 IRQ_TYPE_LEVEL_HIGH 0>;
-			clocks = <&clk26m>,
-				 <&clk26m>,
-				 <&clk26m>;
+			clocks = <&topckgen CLK_TOP_MAINPLL_D5_D4>,
+				 <&topckgen CLK_TOP_SPI_SEL>,
+				 <&infracfg CLK_INFRA_SPI1>;
 			clock-names = "parent-clk", "sel-clk", "spi-clk";
 			status = "disabled";
 		};
@@ -383,9 +649,9 @@
 			#size-cells = <0>;
 			reg = <0 0x11012000 0 0x1000>;
 			interrupts = <GIC_SPI 161 IRQ_TYPE_LEVEL_HIGH 0>;
-			clocks = <&clk26m>,
-				 <&clk26m>,
-				 <&clk26m>;
+			clocks = <&topckgen CLK_TOP_MAINPLL_D5_D4>,
+				 <&topckgen CLK_TOP_SPI_SEL>,
+				 <&infracfg CLK_INFRA_SPI2>;
 			clock-names = "parent-clk", "sel-clk", "spi-clk";
 			status = "disabled";
 		};
@@ -397,9 +663,9 @@
 			#size-cells = <0>;
 			reg = <0 0x11013000 0 0x1000>;
 			interrupts = <GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH 0>;
-			clocks = <&clk26m>,
-				 <&clk26m>,
-				 <&clk26m>;
+			clocks = <&topckgen CLK_TOP_MAINPLL_D5_D4>,
+				 <&topckgen CLK_TOP_SPI_SEL>,
+				 <&infracfg CLK_INFRA_SPI3>;
 			clock-names = "parent-clk", "sel-clk", "spi-clk";
 			status = "disabled";
 		};
@@ -411,9 +677,9 @@
 			#size-cells = <0>;
 			reg = <0 0x11018000 0 0x1000>;
 			interrupts = <GIC_SPI 163 IRQ_TYPE_LEVEL_HIGH 0>;
-			clocks = <&clk26m>,
-				 <&clk26m>,
-				 <&clk26m>;
+			clocks = <&topckgen CLK_TOP_MAINPLL_D5_D4>,
+				 <&topckgen CLK_TOP_SPI_SEL>,
+				 <&infracfg CLK_INFRA_SPI4>;
 			clock-names = "parent-clk", "sel-clk", "spi-clk";
 			status = "disabled";
 		};
@@ -425,9 +691,9 @@
 			#size-cells = <0>;
 			reg = <0 0x11019000 0 0x1000>;
 			interrupts = <GIC_SPI 164 IRQ_TYPE_LEVEL_HIGH 0>;
-			clocks = <&clk26m>,
-				 <&clk26m>,
-				 <&clk26m>;
+			clocks = <&topckgen CLK_TOP_MAINPLL_D5_D4>,
+				 <&topckgen CLK_TOP_SPI_SEL>,
+				 <&infracfg CLK_INFRA_SPI5>;
 			clock-names = "parent-clk", "sel-clk", "spi-clk";
 			status = "disabled";
 		};
@@ -439,9 +705,9 @@
 			#size-cells = <0>;
 			reg = <0 0x1101d000 0 0x1000>;
 			interrupts = <GIC_SPI 165 IRQ_TYPE_LEVEL_HIGH 0>;
-			clocks = <&clk26m>,
-				 <&clk26m>,
-				 <&clk26m>;
+			clocks = <&topckgen CLK_TOP_MAINPLL_D5_D4>,
+				 <&topckgen CLK_TOP_SPI_SEL>,
+				 <&infracfg CLK_INFRA_SPI6>;
 			clock-names = "parent-clk", "sel-clk", "spi-clk";
 			status = "disabled";
 		};
@@ -453,38 +719,252 @@
 			#size-cells = <0>;
 			reg = <0 0x1101e000 0 0x1000>;
 			interrupts = <GIC_SPI 166 IRQ_TYPE_LEVEL_HIGH 0>;
-			clocks = <&clk26m>,
-				 <&clk26m>,
-				 <&clk26m>;
+			clocks = <&topckgen CLK_TOP_MAINPLL_D5_D4>,
+				 <&topckgen CLK_TOP_SPI_SEL>,
+				 <&infracfg CLK_INFRA_SPI7>;
 			clock-names = "parent-clk", "sel-clk", "spi-clk";
 			status = "disabled";
 		};
 
+		scp: scp@10500000 {
+			compatible = "mediatek,mt8192-scp";
+			reg = <0 0x10500000 0 0x100000>,
+			      <0 0x10720000 0 0xe0000>,
+			      <0 0x10700000 0 0x8000>;
+			reg-names = "sram", "cfg", "l1tcm";
+			interrupts = <GIC_SPI 435 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&infracfg CLK_INFRA_SCPSYS>;
+			clock-names = "main";
+			status = "disabled";
+		};
+
+		xhci: usb@11200000 {
+			compatible = "mediatek,mt8192-xhci",
+				     "mediatek,mtk-xhci";
+			reg = <0 0x11200000 0 0x1000>,
+			      <0 0x11203e00 0 0x0100>;
+			reg-names = "mac", "ippc";
+			interrupts-extended = <&gic GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH 0>;
+			interrupt-names = "host";
+			phys = <&u2port0 PHY_TYPE_USB2>,
+			       <&u3port0 PHY_TYPE_USB3>;
+			assigned-clocks = <&topckgen CLK_TOP_USB_TOP_SEL>,
+					  <&topckgen CLK_TOP_SSUSB_XHCI_SEL>;
+			assigned-clock-parents = <&topckgen CLK_TOP_UNIVPLL_D5_D4>,
+						 <&topckgen CLK_TOP_UNIVPLL_D5_D4>;
+			clocks = <&infracfg CLK_INFRA_SSUSB>,
+				 <&apmixedsys CLK_APMIXED_USBPLL>,
+				 <&clk26m>,
+				 <&clk26m>,
+				 <&infracfg CLK_INFRA_SSUSB_XHCI>;
+			clock-names = "sys_ck", "ref_ck", "mcu_ck", "dma_ck",
+				      "xhci_ck";
+			wakeup-source;
+			mediatek,syscon-wakeup = <&pericfg 0x420 102>;
+			status = "disabled";
+		};
+
+		audsys: syscon@11210000 {
+			compatible = "mediatek,mt8192-audsys", "syscon";
+			reg = <0 0x11210000 0 0x2000>;
+			#clock-cells = <1>;
+
+			afe: mt8192-afe-pcm {
+				compatible = "mediatek,mt8192-audio";
+				interrupts = <GIC_SPI 202 IRQ_TYPE_LEVEL_HIGH 0>;
+				resets = <&watchdog 17>;
+				reset-names = "audiosys";
+				mediatek,apmixedsys = <&apmixedsys>;
+				mediatek,infracfg = <&infracfg>;
+				mediatek,topckgen = <&topckgen>;
+				power-domains = <&spm MT8192_POWER_DOMAIN_AUDIO>;
+				clocks = <&audsys CLK_AUD_AFE>,
+					 <&audsys CLK_AUD_DAC>,
+					 <&audsys CLK_AUD_DAC_PREDIS>,
+					 <&audsys CLK_AUD_ADC>,
+					 <&audsys CLK_AUD_ADDA6_ADC>,
+					 <&audsys CLK_AUD_22M>,
+					 <&audsys CLK_AUD_24M>,
+					 <&audsys CLK_AUD_APLL_TUNER>,
+					 <&audsys CLK_AUD_APLL2_TUNER>,
+					 <&audsys CLK_AUD_TDM>,
+					 <&audsys CLK_AUD_TML>,
+					 <&audsys CLK_AUD_NLE>,
+					 <&audsys CLK_AUD_DAC_HIRES>,
+					 <&audsys CLK_AUD_ADC_HIRES>,
+					 <&audsys CLK_AUD_ADC_HIRES_TML>,
+					 <&audsys CLK_AUD_ADDA6_ADC_HIRES>,
+					 <&audsys CLK_AUD_3RD_DAC>,
+					 <&audsys CLK_AUD_3RD_DAC_PREDIS>,
+					 <&audsys CLK_AUD_3RD_DAC_TML>,
+					 <&audsys CLK_AUD_3RD_DAC_HIRES>,
+					 <&infracfg CLK_INFRA_AUDIO>,
+					 <&infracfg CLK_INFRA_AUDIO_26M_B>,
+					 <&topckgen CLK_TOP_AUDIO_SEL>,
+					 <&topckgen CLK_TOP_AUD_INTBUS_SEL>,
+					 <&topckgen CLK_TOP_MAINPLL_D4_D4>,
+					 <&topckgen CLK_TOP_AUD_1_SEL>,
+					 <&topckgen CLK_TOP_APLL1>,
+					 <&topckgen CLK_TOP_AUD_2_SEL>,
+					 <&topckgen CLK_TOP_APLL2>,
+					 <&topckgen CLK_TOP_AUD_ENGEN1_SEL>,
+					 <&topckgen CLK_TOP_APLL1_D4>,
+					 <&topckgen CLK_TOP_AUD_ENGEN2_SEL>,
+					 <&topckgen CLK_TOP_APLL2_D4>,
+					 <&topckgen CLK_TOP_APLL_I2S0_M_SEL>,
+					 <&topckgen CLK_TOP_APLL_I2S1_M_SEL>,
+					 <&topckgen CLK_TOP_APLL_I2S2_M_SEL>,
+					 <&topckgen CLK_TOP_APLL_I2S3_M_SEL>,
+					 <&topckgen CLK_TOP_APLL_I2S4_M_SEL>,
+					 <&topckgen CLK_TOP_APLL_I2S5_M_SEL>,
+					 <&topckgen CLK_TOP_APLL_I2S6_M_SEL>,
+					 <&topckgen CLK_TOP_APLL_I2S7_M_SEL>,
+					 <&topckgen CLK_TOP_APLL_I2S8_M_SEL>,
+					 <&topckgen CLK_TOP_APLL_I2S9_M_SEL>,
+					 <&topckgen CLK_TOP_APLL12_DIV0>,
+					 <&topckgen CLK_TOP_APLL12_DIV1>,
+					 <&topckgen CLK_TOP_APLL12_DIV2>,
+					 <&topckgen CLK_TOP_APLL12_DIV3>,
+					 <&topckgen CLK_TOP_APLL12_DIV4>,
+					 <&topckgen CLK_TOP_APLL12_DIVB>,
+					 <&topckgen CLK_TOP_APLL12_DIV5>,
+					 <&topckgen CLK_TOP_APLL12_DIV6>,
+					 <&topckgen CLK_TOP_APLL12_DIV7>,
+					 <&topckgen CLK_TOP_APLL12_DIV8>,
+					 <&topckgen CLK_TOP_APLL12_DIV9>,
+					 <&topckgen CLK_TOP_AUDIO_H_SEL>,
+					 <&clk26m>;
+				clock-names = "aud_afe_clk",
+					      "aud_dac_clk",
+					      "aud_dac_predis_clk",
+					      "aud_adc_clk",
+					      "aud_adda6_adc_clk",
+					      "aud_apll22m_clk",
+					      "aud_apll24m_clk",
+					      "aud_apll1_tuner_clk",
+					      "aud_apll2_tuner_clk",
+					      "aud_tdm_clk",
+					      "aud_tml_clk",
+					      "aud_nle",
+					      "aud_dac_hires_clk",
+					      "aud_adc_hires_clk",
+					      "aud_adc_hires_tml",
+					      "aud_adda6_adc_hires_clk",
+					      "aud_3rd_dac_clk",
+					      "aud_3rd_dac_predis_clk",
+					      "aud_3rd_dac_tml",
+					      "aud_3rd_dac_hires_clk",
+					      "aud_infra_clk",
+					      "aud_infra_26m_clk",
+					      "top_mux_audio",
+					      "top_mux_audio_int",
+					      "top_mainpll_d4_d4",
+					      "top_mux_aud_1",
+					      "top_apll1_ck",
+					      "top_mux_aud_2",
+					      "top_apll2_ck",
+					      "top_mux_aud_eng1",
+					      "top_apll1_d4",
+					      "top_mux_aud_eng2",
+					      "top_apll2_d4",
+					      "top_i2s0_m_sel",
+					      "top_i2s1_m_sel",
+					      "top_i2s2_m_sel",
+					      "top_i2s3_m_sel",
+					      "top_i2s4_m_sel",
+					      "top_i2s5_m_sel",
+					      "top_i2s6_m_sel",
+					      "top_i2s7_m_sel",
+					      "top_i2s8_m_sel",
+					      "top_i2s9_m_sel",
+					      "top_apll12_div0",
+					      "top_apll12_div1",
+					      "top_apll12_div2",
+					      "top_apll12_div3",
+					      "top_apll12_div4",
+					      "top_apll12_divb",
+					      "top_apll12_div5",
+					      "top_apll12_div6",
+					      "top_apll12_div7",
+					      "top_apll12_div8",
+					      "top_apll12_div9",
+					      "top_mux_audio_h",
+					      "top_clk26m_clk";
+			};
+		};
+
+		pcie: pcie@11230000 {
+			compatible = "mediatek,mt8192-pcie";
+			device_type = "pci";
+			reg = <0 0x11230000 0 0x2000>;
+			reg-names = "pcie-mac";
+			#address-cells = <3>;
+			#size-cells = <2>;
+			clocks = <&infracfg CLK_INFRA_PCIE_PL_P_250M>,
+				 <&infracfg CLK_INFRA_PCIE_TL_26M>,
+				 <&infracfg CLK_INFRA_PCIE_TL_96M>,
+				 <&infracfg CLK_INFRA_PCIE_TL_32K>,
+				 <&infracfg CLK_INFRA_PCIE_PERI_26M>,
+				 <&infracfg CLK_INFRA_PCIE_TOP_H_133M>;
+			clock-names = "pl_250m", "tl_26m", "tl_96m",
+				      "tl_32k", "peri_26m", "top_133m";
+			assigned-clocks = <&topckgen CLK_TOP_TL_SEL>;
+			assigned-clock-parents = <&topckgen CLK_TOP_MAINPLL_D6_D4>;
+			interrupts = <GIC_SPI 251 IRQ_TYPE_LEVEL_HIGH 0>;
+			bus-range = <0x00 0xff>;
+			ranges = <0x82000000 0 0x12000000 0x0 0x12000000 0 0x0800000>,
+				 <0x81000000 0 0x12800000 0x0 0x12800000 0 0x0800000>;
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 7>;
+			interrupt-map = <0 0 0 1 &pcie_intc0 0>,
+					<0 0 0 2 &pcie_intc0 1>,
+					<0 0 0 3 &pcie_intc0 2>,
+					<0 0 0 4 &pcie_intc0 3>;
+
+			pcie_intc0: interrupt-controller {
+				interrupt-controller;
+				#address-cells = <0>;
+				#interrupt-cells = <1>;
+			};
+		};
+
 		nor_flash: spi@11234000 {
 			compatible = "mediatek,mt8192-nor";
 			reg = <0 0x11234000 0 0xe0>;
 			interrupts = <GIC_SPI 431 IRQ_TYPE_LEVEL_HIGH 0>;
-			clocks = <&clk26m>,
-				 <&clk26m>,
-				 <&clk26m>;
+			clocks = <&topckgen CLK_TOP_SFLASH_SEL>,
+				 <&infracfg CLK_INFRA_FLASHIF_SFLASH>,
+				 <&infracfg CLK_INFRA_FLASHIF_TOP_H_133M>;
 			clock-names = "spi", "sf", "axi";
+			assigned-clocks = <&topckgen CLK_TOP_SFLASH_SEL>;
+			assigned-clock-parents = <&clk26m>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			status = "disable";
+			status = "disabled";
 		};
 
-		audsys: clock-controller@11210000 {
-			compatible = "mediatek,mt8192-audsys", "syscon";
-			reg = <0 0x11210000 0 0x1000>;
-			#clock-cells = <1>;
+		efuse: efuse@11c10000 {
+			compatible = "mediatek,mt8192-efuse", "mediatek,efuse";
+			reg = <0 0x11c10000 0 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			lvts_e_data1: data1@1c0 {
+				reg = <0x1c0 0x58>;
+			};
+
+			svs_calibration: calib@580 {
+				reg = <0x580 0x68>;
+			};
 		};
 
-		i2c3: i2c3@11cb0000 {
+		i2c3: i2c@11cb0000 {
 			compatible = "mediatek,mt8192-i2c";
 			reg = <0 0x11cb0000 0 0x1000>,
 			      <0 0x10217300 0 0x80>;
 			interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH 0>;
-			clocks = <&clk26m>, <&clk26m>;
+			clocks = <&imp_iic_wrap_e CLK_IMP_IIC_WRAP_E_I2C3>,
+				 <&infracfg CLK_INFRA_AP_DMA>;
 			clock-names = "main", "dma";
 			clock-div = <1>;
 			#address-cells = <1>;
@@ -498,12 +978,13 @@
 			#clock-cells = <1>;
 		};
 
-		i2c7: i2c7@11d00000 {
+		i2c7: i2c@11d00000 {
 			compatible = "mediatek,mt8192-i2c";
 			reg = <0 0x11d00000 0 0x1000>,
 			      <0 0x10217600 0 0x180>;
 			interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH 0>;
-			clocks = <&clk26m>, <&clk26m>;
+			clocks = <&imp_iic_wrap_s CLK_IMP_IIC_WRAP_S_I2C7>,
+				 <&infracfg CLK_INFRA_AP_DMA>;
 			clock-names = "main", "dma";
 			clock-div = <1>;
 			#address-cells = <1>;
@@ -511,12 +992,13 @@
 			status = "disabled";
 		};
 
-		i2c8: i2c8@11d01000 {
+		i2c8: i2c@11d01000 {
 			compatible = "mediatek,mt8192-i2c";
 			reg = <0 0x11d01000 0 0x1000>,
 			      <0 0x10217780 0 0x180>;
 			interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH 0>;
-			clocks = <&clk26m>, <&clk26m>;
+			clocks = <&imp_iic_wrap_s CLK_IMP_IIC_WRAP_S_I2C8>,
+				 <&infracfg CLK_INFRA_AP_DMA>;
 			clock-names = "main", "dma";
 			clock-div = <1>;
 			#address-cells = <1>;
@@ -524,12 +1006,13 @@
 			status = "disabled";
 		};
 
-		i2c9: i2c9@11d02000 {
+		i2c9: i2c@11d02000 {
 			compatible = "mediatek,mt8192-i2c";
 			reg = <0 0x11d02000 0 0x1000>,
 			      <0 0x10217900 0 0x180>;
 			interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH 0>;
-			clocks = <&clk26m>, <&clk26m>;
+			clocks = <&imp_iic_wrap_s CLK_IMP_IIC_WRAP_S_I2C9>,
+				 <&infracfg CLK_INFRA_AP_DMA>;
 			clock-names = "main", "dma";
 			clock-div = <1>;
 			#address-cells = <1>;
@@ -543,12 +1026,13 @@
 			#clock-cells = <1>;
 		};
 
-		i2c1: i2c1@11d20000 {
+		i2c1: i2c@11d20000 {
 			compatible = "mediatek,mt8192-i2c";
 			reg = <0 0x11d20000 0 0x1000>,
 			      <0 0x10217100 0 0x80>;
 			interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH 0>;
-			clocks = <&clk26m>, <&clk26m>;
+			clocks = <&imp_iic_wrap_ws CLK_IMP_IIC_WRAP_WS_I2C1>,
+				 <&infracfg CLK_INFRA_AP_DMA>;
 			clock-names = "main", "dma";
 			clock-div = <1>;
 			#address-cells = <1>;
@@ -556,12 +1040,13 @@
 			status = "disabled";
 		};
 
-		i2c2: i2c2@11d21000 {
+		i2c2: i2c@11d21000 {
 			compatible = "mediatek,mt8192-i2c";
 			reg = <0 0x11d21000 0 0x1000>,
 			      <0 0x10217180 0 0x180>;
 			interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH 0>;
-			clocks = <&clk26m>, <&clk26m>;
+			clocks = <&imp_iic_wrap_ws CLK_IMP_IIC_WRAP_WS_I2C2>,
+				 <&infracfg CLK_INFRA_AP_DMA>;
 			clock-names = "main", "dma";
 			clock-div = <1>;
 			#address-cells = <1>;
@@ -569,12 +1054,13 @@
 			status = "disabled";
 		};
 
-		i2c4: i2c4@11d22000 {
+		i2c4: i2c@11d22000 {
 			compatible = "mediatek,mt8192-i2c";
 			reg = <0 0x11d22000 0 0x1000>,
 			      <0 0x10217380 0 0x180>;
 			interrupts = <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH 0>;
-			clocks = <&clk26m>, <&clk26m>;
+			clocks = <&imp_iic_wrap_ws CLK_IMP_IIC_WRAP_WS_I2C4>,
+				 <&infracfg CLK_INFRA_AP_DMA>;
 			clock-names = "main", "dma";
 			clock-div = <1>;
 			#address-cells = <1>;
@@ -588,12 +1074,13 @@
 			#clock-cells = <1>;
 		};
 
-		i2c5: i2c5@11e00000 {
+		i2c5: i2c@11e00000 {
 			compatible = "mediatek,mt8192-i2c";
 			reg = <0 0x11e00000 0 0x1000>,
 			      <0 0x10217500 0 0x80>;
 			interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH 0>;
-			clocks = <&clk26m>, <&clk26m>;
+			clocks = <&imp_iic_wrap_w CLK_IMP_IIC_WRAP_W_I2C5>,
+				 <&infracfg CLK_INFRA_AP_DMA>;
 			clock-names = "main", "dma";
 			clock-div = <1>;
 			#address-cells = <1>;
@@ -607,12 +1094,45 @@
 			#clock-cells = <1>;
 		};
 
-		i2c0: i2c0@11f00000 {
+		u3phy0: t-phy@11e40000 {
+			compatible = "mediatek,mt8192-tphy",
+				     "mediatek,generic-tphy-v2";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x0 0x11e40000 0x1000>;
+
+			u2port0: usb-phy@0 {
+				reg = <0x0 0x700>;
+				clocks = <&clk26m>;
+				clock-names = "ref";
+				#phy-cells = <1>;
+			};
+
+			u3port0: usb-phy@700 {
+				reg = <0x700 0x900>;
+				clocks = <&clk26m>;
+				clock-names = "ref";
+				#phy-cells = <1>;
+			};
+		};
+
+		mipi_tx0: dsi-phy@11e50000 {
+			compatible = "mediatek,mt8183-mipi-tx";
+			reg = <0 0x11e50000 0 0x1000>;
+			clocks = <&apmixedsys CLK_APMIXED_MIPID26M>;
+			#clock-cells = <0>;
+			#phy-cells = <0>;
+			clock-output-names = "mipi_tx0_pll";
+			status = "disabled";
+		};
+
+		i2c0: i2c@11f00000 {
 			compatible = "mediatek,mt8192-i2c";
 			reg = <0 0x11f00000 0 0x1000>,
 			      <0 0x10217080 0 0x80>;
 			interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH 0>;
-			clocks = <&clk26m>, <&clk26m>;
+			clocks = <&imp_iic_wrap_n CLK_IMP_IIC_WRAP_N_I2C0>,
+				 <&infracfg CLK_INFRA_AP_DMA>;
 			clock-names = "main", "dma";
 			clock-div = <1>;
 			#address-cells = <1>;
@@ -620,12 +1140,13 @@
 			status = "disabled";
 		};
 
-		i2c6: i2c6@11f01000 {
+		i2c6: i2c@11f01000 {
 			compatible = "mediatek,mt8192-i2c";
 			reg = <0 0x11f01000 0 0x1000>,
 			      <0 0x10217580 0 0x80>;
 			interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH 0>;
-			clocks = <&clk26m>, <&clk26m>;
+			clocks = <&imp_iic_wrap_n CLK_IMP_IIC_WRAP_N_I2C6>,
+				 <&infracfg CLK_INFRA_AP_DMA>;
 			clock-names = "main", "dma";
 			clock-div = <1>;
 			#address-cells = <1>;
@@ -645,10 +1166,36 @@
 			#clock-cells = <1>;
 		};
 
-		msdc: clock-controller@11f60000 {
-			compatible = "mediatek,mt8192-msdc";
-			reg = <0 0x11f60000 0 0x1000>;
-			#clock-cells = <1>;
+		mmc0: mmc@11f60000 {
+			compatible = "mediatek,mt8192-mmc", "mediatek,mt8183-mmc";
+			reg = <0 0x11f60000 0 0x1000>, <0 0x11f50000 0 0x1000>;
+			interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&topckgen CLK_TOP_MSDC50_0_SEL>,
+				 <&msdc_top CLK_MSDC_TOP_H_MST_0P>,
+				 <&msdc_top CLK_MSDC_TOP_SRC_0P>,
+				 <&msdc_top CLK_MSDC_TOP_P_CFG>,
+				 <&msdc_top CLK_MSDC_TOP_P_MSDC0>,
+				 <&msdc_top CLK_MSDC_TOP_AXI>,
+				 <&msdc_top CLK_MSDC_TOP_AHB2AXI_BRG_AXI>;
+			clock-names = "source", "hclk", "source_cg", "sys_cg",
+				      "pclk_cg", "axi_cg", "ahb_cg";
+			status = "disabled";
+		};
+
+		mmc1: mmc@11f70000 {
+			compatible = "mediatek,mt8192-mmc", "mediatek,mt8183-mmc";
+			reg = <0 0x11f70000 0 0x1000>, <0 0x11c70000 0 0x1000>;
+			interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&topckgen CLK_TOP_MSDC30_1_SEL>,
+				 <&msdc_top CLK_MSDC_TOP_H_MST_1P>,
+				 <&msdc_top CLK_MSDC_TOP_SRC_1P>,
+				 <&msdc_top CLK_MSDC_TOP_P_CFG>,
+				 <&msdc_top CLK_MSDC_TOP_P_MSDC1>,
+				 <&msdc_top CLK_MSDC_TOP_AXI>,
+				 <&msdc_top CLK_MSDC_TOP_AHB2AXI_BRG_AXI>;
+			clock-names = "source", "hclk", "source_cg", "sys_cg",
+				      "pclk_cg", "axi_cg", "ahb_cg";
+			status = "disabled";
 		};
 
 		mfgcfg: clock-controller@13fbf000 {
@@ -661,6 +1208,211 @@
 			compatible = "mediatek,mt8192-mmsys", "syscon";
 			reg = <0 0x14000000 0 0x1000>;
 			#clock-cells = <1>;
+			#reset-cells = <1>;
+			mboxes = <&gce 0 CMDQ_THR_PRIO_HIGHEST>,
+				 <&gce 1 CMDQ_THR_PRIO_HIGHEST>;
+			mediatek,gce-client-reg = <&gce SUBSYS_1400XXXX 0 0x1000>;
+		};
+
+		mutex: mutex@14001000 {
+			compatible = "mediatek,mt8192-disp-mutex";
+			reg = <0 0x14001000 0 0x1000>;
+			interrupts = <GIC_SPI 252 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&mmsys CLK_MM_DISP_MUTEX0>;
+			mediatek,gce-events = <CMDQ_EVENT_DISP_STREAM_DONE_ENG_EVENT_0>,
+					      <CMDQ_EVENT_DISP_STREAM_DONE_ENG_EVENT_1>;
+			power-domains = <&spm MT8192_POWER_DOMAIN_DISP>;
+		};
+
+		smi_common: smi@14002000 {
+			compatible = "mediatek,mt8192-smi-common";
+			reg = <0 0x14002000 0 0x1000>;
+			clocks = <&mmsys CLK_MM_SMI_COMMON>,
+				 <&mmsys CLK_MM_SMI_INFRA>,
+				 <&mmsys CLK_MM_SMI_GALS>,
+				 <&mmsys CLK_MM_SMI_GALS>;
+			clock-names = "apb", "smi", "gals0", "gals1";
+			power-domains = <&spm MT8192_POWER_DOMAIN_DISP>;
+		};
+
+		larb0: larb@14003000 {
+			compatible = "mediatek,mt8192-smi-larb";
+			reg = <0 0x14003000 0 0x1000>;
+			mediatek,larb-id = <0>;
+			mediatek,smi = <&smi_common>;
+			clocks = <&clk26m>, <&clk26m>;
+			clock-names = "apb", "smi";
+			power-domains = <&spm MT8192_POWER_DOMAIN_DISP>;
+		};
+
+		larb1: larb@14004000 {
+			compatible = "mediatek,mt8192-smi-larb";
+			reg = <0 0x14004000 0 0x1000>;
+			mediatek,larb-id = <1>;
+			mediatek,smi = <&smi_common>;
+			clocks = <&clk26m>, <&clk26m>;
+			clock-names = "apb", "smi";
+			power-domains = <&spm MT8192_POWER_DOMAIN_DISP>;
+		};
+
+		ovl0: ovl@14005000 {
+			compatible = "mediatek,mt8192-disp-ovl";
+			reg = <0 0x14005000 0 0x1000>;
+			interrupts = <GIC_SPI 254 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&mmsys CLK_MM_DISP_OVL0>;
+			iommus = <&iommu0 M4U_PORT_L0_OVL_RDMA0>,
+				 <&iommu0 M4U_PORT_L0_OVL_RDMA0_HDR>;
+			power-domains = <&spm MT8192_POWER_DOMAIN_DISP>;
+			mediatek,gce-client-reg = <&gce SUBSYS_1400XXXX 0x5000 0x1000>;
+		};
+
+		ovl_2l0: ovl@14006000 {
+			compatible = "mediatek,mt8192-disp-ovl-2l";
+			reg = <0 0x14006000 0 0x1000>;
+			interrupts = <GIC_SPI 255 IRQ_TYPE_LEVEL_HIGH 0>;
+			power-domains = <&spm MT8192_POWER_DOMAIN_DISP>;
+			clocks = <&mmsys CLK_MM_DISP_OVL0_2L>;
+			iommus = <&iommu0 M4U_PORT_L1_OVL_2L_RDMA0>,
+				 <&iommu0 M4U_PORT_L1_OVL_2L_RDMA0_HDR>;
+			mediatek,gce-client-reg = <&gce SUBSYS_1400XXXX 0x6000 0x1000>;
+		};
+
+		rdma0: rdma@14007000 {
+			compatible = "mediatek,mt8192-disp-rdma",
+				     "mediatek,mt8183-disp-rdma";
+			reg = <0 0x14007000 0 0x1000>;
+			interrupts = <GIC_SPI 256 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&mmsys CLK_MM_DISP_RDMA0>;
+			iommus = <&iommu0 M4U_PORT_L0_DISP_RDMA0>;
+			mediatek,rdma-fifo-size = <5120>;
+			power-domains = <&spm MT8192_POWER_DOMAIN_DISP>;
+			mediatek,gce-client-reg = <&gce SUBSYS_1400XXXX 0x7000 0x1000>;
+		};
+
+		color0: color@14009000 {
+			compatible = "mediatek,mt8192-disp-color",
+				     "mediatek,mt8173-disp-color";
+			reg = <0 0x14009000 0 0x1000>;
+			interrupts = <GIC_SPI 258 IRQ_TYPE_LEVEL_HIGH 0>;
+			power-domains = <&spm MT8192_POWER_DOMAIN_DISP>;
+			clocks = <&mmsys CLK_MM_DISP_COLOR0>;
+			mediatek,gce-client-reg = <&gce SUBSYS_1400XXXX 0x9000 0x1000>;
+		};
+
+		ccorr0: ccorr@1400a000 {
+			compatible = "mediatek,mt8192-disp-ccorr";
+			reg = <0 0x1400a000 0 0x1000>;
+			interrupts = <GIC_SPI 259 IRQ_TYPE_LEVEL_HIGH 0>;
+			power-domains = <&spm MT8192_POWER_DOMAIN_DISP>;
+			clocks = <&mmsys CLK_MM_DISP_CCORR0>;
+			mediatek,gce-client-reg = <&gce SUBSYS_1400XXXX 0xa000 0x1000>;
+		};
+
+		aal0: aal@1400b000 {
+			compatible = "mediatek,mt8192-disp-aal",
+				     "mediatek,mt8183-disp-aal";
+			reg = <0 0x1400b000 0 0x1000>;
+			interrupts = <GIC_SPI 260 IRQ_TYPE_LEVEL_HIGH 0>;
+			power-domains = <&spm MT8192_POWER_DOMAIN_DISP>;
+			clocks = <&mmsys CLK_MM_DISP_AAL0>;
+			mediatek,gce-client-reg = <&gce SUBSYS_1400XXXX 0xb000 0x1000>;
+		};
+
+		gamma0: gamma@1400c000 {
+			compatible = "mediatek,mt8192-disp-gamma",
+				     "mediatek,mt8183-disp-gamma";
+			reg = <0 0x1400c000 0 0x1000>;
+			interrupts = <GIC_SPI 261 IRQ_TYPE_LEVEL_HIGH 0>;
+			power-domains = <&spm MT8192_POWER_DOMAIN_DISP>;
+			clocks = <&mmsys CLK_MM_DISP_GAMMA0>;
+			mediatek,gce-client-reg = <&gce SUBSYS_1400XXXX 0xc000 0x1000>;
+		};
+
+		postmask0: postmask@1400d000 {
+			compatible = "mediatek,mt8192-disp-postmask";
+			reg = <0 0x1400d000 0 0x1000>;
+			interrupts = <GIC_SPI 262 IRQ_TYPE_LEVEL_HIGH 0>;
+			power-domains = <&spm MT8192_POWER_DOMAIN_DISP>;
+			clocks = <&mmsys CLK_MM_DISP_POSTMASK0>;
+			mediatek,gce-client-reg = <&gce SUBSYS_1400XXXX 0xd000 0x1000>;
+		};
+
+		dither0: dither@1400e000 {
+			compatible = "mediatek,mt8192-disp-dither",
+				     "mediatek,mt8183-disp-dither";
+			reg = <0 0x1400e000 0 0x1000>;
+			interrupts = <GIC_SPI 263 IRQ_TYPE_LEVEL_HIGH 0>;
+			power-domains = <&spm MT8192_POWER_DOMAIN_DISP>;
+			clocks = <&mmsys CLK_MM_DISP_DITHER0>;
+			mediatek,gce-client-reg = <&gce SUBSYS_1400XXXX 0xe000 0x1000>;
+		};
+
+		dsi0: dsi@14010000 {
+			compatible = "mediatek,mt8183-dsi";
+			reg = <0 0x14010000 0 0x1000>;
+			interrupts = <GIC_SPI 265 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&mmsys CLK_MM_DSI0>,
+				 <&mmsys CLK_MM_DSI_DSI0>,
+				 <&mipi_tx0>;
+			clock-names = "engine", "digital", "hs";
+			phys = <&mipi_tx0>;
+			phy-names = "dphy";
+			power-domains = <&spm MT8192_POWER_DOMAIN_DISP>;
+			resets = <&mmsys MT8192_MMSYS_SW0_RST_B_DISP_DSI0>;
+			status = "disabled";
+
+			port {
+				dsi_out: endpoint { };
+			};
+		};
+
+		ovl_2l2: ovl@14014000 {
+			compatible = "mediatek,mt8192-disp-ovl-2l";
+			reg = <0 0x14014000 0 0x1000>;
+			interrupts = <GIC_SPI 268 IRQ_TYPE_LEVEL_HIGH 0>;
+			power-domains = <&spm MT8192_POWER_DOMAIN_DISP>;
+			clocks = <&mmsys CLK_MM_DISP_OVL2_2L>;
+			iommus = <&iommu0 M4U_PORT_L1_OVL_2L_RDMA2>,
+				 <&iommu0 M4U_PORT_L1_OVL_2L_RDMA2_HDR>;
+			mediatek,gce-client-reg = <&gce SUBSYS_1401XXXX 0x4000 0x1000>;
+		};
+
+		rdma4: rdma@14015000 {
+			compatible = "mediatek,mt8192-disp-rdma",
+				     "mediatek,mt8183-disp-rdma";
+			reg = <0 0x14015000 0 0x1000>;
+			interrupts = <GIC_SPI 269 IRQ_TYPE_LEVEL_HIGH 0>;
+			power-domains = <&spm MT8192_POWER_DOMAIN_DISP>;
+			clocks = <&mmsys CLK_MM_DISP_RDMA4>;
+			iommus = <&iommu0 M4U_PORT_L1_DISP_RDMA4>;
+			mediatek,rdma-fifo-size = <2048>;
+			mediatek,gce-client-reg = <&gce SUBSYS_1401XXXX 0x5000 0x1000>;
+		};
+
+		dpi0: dpi@14016000 {
+			compatible = "mediatek,mt8192-dpi";
+			reg = <0 0x14016000 0 0x1000>;
+			interrupts = <GIC_SPI 270 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&mmsys CLK_MM_DPI_DPI0>,
+				 <&mmsys CLK_MM_DISP_DPI0>,
+				 <&apmixedsys CLK_APMIXED_TVDPLL>;
+			clock-names = "pixel", "engine", "pll";
+			status = "disabled";
+		};
+
+		iommu0: m4u@1401d000 {
+			compatible = "mediatek,mt8192-m4u";
+			reg = <0 0x1401d000 0 0x1000>;
+			mediatek,larbs = <&larb0>, <&larb1>, <&larb2>,
+					 <&larb4>, <&larb5>, <&larb7>,
+					 <&larb9>, <&larb11>, <&larb13>,
+					 <&larb14>, <&larb16>, <&larb17>,
+					 <&larb18>, <&larb19>, <&larb20>;
+			interrupts = <GIC_SPI 277 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&mmsys CLK_MM_SMI_IOMMU>;
+			clock-names = "bclk";
+			power-domains = <&spm MT8192_POWER_DOMAIN_DISP>;
+			#iommu-cells = <1>;
 		};
 
 		imgsys: clock-controller@15020000 {
@@ -669,18 +1421,62 @@
 			#clock-cells = <1>;
 		};
 
+		larb9: larb@1502e000 {
+			compatible = "mediatek,mt8192-smi-larb";
+			reg = <0 0x1502e000 0 0x1000>;
+			mediatek,larb-id = <9>;
+			mediatek,smi = <&smi_common>;
+			clocks = <&imgsys CLK_IMG_LARB9>,
+				 <&imgsys CLK_IMG_LARB9>;
+			clock-names = "apb", "smi";
+			power-domains = <&spm MT8192_POWER_DOMAIN_ISP>;
+		};
+
 		imgsys2: clock-controller@15820000 {
 			compatible = "mediatek,mt8192-imgsys2";
 			reg = <0 0x15820000 0 0x1000>;
 			#clock-cells = <1>;
 		};
 
+		larb11: larb@1582e000 {
+			compatible = "mediatek,mt8192-smi-larb";
+			reg = <0 0x1582e000 0 0x1000>;
+			mediatek,larb-id = <11>;
+			mediatek,smi = <&smi_common>;
+			clocks = <&imgsys2 CLK_IMG2_LARB11>,
+				 <&imgsys2 CLK_IMG2_LARB11>;
+			clock-names = "apb", "smi";
+			power-domains = <&spm MT8192_POWER_DOMAIN_ISP2>;
+		};
+
+		larb5: larb@1600d000 {
+			compatible = "mediatek,mt8192-smi-larb";
+			reg = <0 0x1600d000 0 0x1000>;
+			mediatek,larb-id = <5>;
+			mediatek,smi = <&smi_common>;
+			clocks = <&vdecsys_soc CLK_VDEC_SOC_LARB1>,
+				 <&vdecsys_soc CLK_VDEC_SOC_LARB1>;
+			clock-names = "apb", "smi";
+			power-domains = <&spm MT8192_POWER_DOMAIN_VDEC>;
+		};
+
 		vdecsys_soc: clock-controller@1600f000 {
 			compatible = "mediatek,mt8192-vdecsys_soc";
 			reg = <0 0x1600f000 0 0x1000>;
 			#clock-cells = <1>;
 		};
 
+		larb4: larb@1602e000 {
+			compatible = "mediatek,mt8192-smi-larb";
+			reg = <0 0x1602e000 0 0x1000>;
+			mediatek,larb-id = <4>;
+			mediatek,smi = <&smi_common>;
+			clocks = <&vdecsys CLK_VDEC_SOC_LARB1>,
+				 <&vdecsys CLK_VDEC_SOC_LARB1>;
+			clock-names = "apb", "smi";
+			power-domains = <&spm MT8192_POWER_DOMAIN_VDEC2>;
+		};
+
 		vdecsys: clock-controller@1602f000 {
 			compatible = "mediatek,mt8192-vdecsys";
 			reg = <0 0x1602f000 0 0x1000>;
@@ -693,12 +1489,101 @@
 			#clock-cells = <1>;
 		};
 
+		larb7: larb@17010000 {
+			compatible = "mediatek,mt8192-smi-larb";
+			reg = <0 0x17010000 0 0x1000>;
+			mediatek,larb-id = <7>;
+			mediatek,smi = <&smi_common>;
+			clocks = <&vencsys CLK_VENC_SET0_LARB>,
+				 <&vencsys CLK_VENC_SET1_VENC>;
+			clock-names = "apb", "smi";
+			power-domains = <&spm MT8192_POWER_DOMAIN_VENC>;
+		};
+
+		vcodec_enc: vcodec@17020000 {
+			compatible = "mediatek,mt8192-vcodec-enc";
+			reg = <0 0x17020000 0 0x2000>;
+			iommus = <&iommu0 M4U_PORT_L7_VENC_RCPU>,
+				 <&iommu0 M4U_PORT_L7_VENC_REC>,
+				 <&iommu0 M4U_PORT_L7_VENC_BSDMA>,
+				 <&iommu0 M4U_PORT_L7_VENC_SV_COMV>,
+				 <&iommu0 M4U_PORT_L7_VENC_RD_COMV>,
+				 <&iommu0 M4U_PORT_L7_VENC_CUR_LUMA>,
+				 <&iommu0 M4U_PORT_L7_VENC_CUR_CHROMA>,
+				 <&iommu0 M4U_PORT_L7_VENC_REF_LUMA>,
+				 <&iommu0 M4U_PORT_L7_VENC_REF_CHROMA>,
+				 <&iommu0 M4U_PORT_L7_VENC_SUB_R_LUMA>,
+				 <&iommu0 M4U_PORT_L7_VENC_SUB_W_LUMA>;
+			interrupts = <GIC_SPI 309 IRQ_TYPE_LEVEL_HIGH 0>;
+			mediatek,scp = <&scp>;
+			power-domains = <&spm MT8192_POWER_DOMAIN_VENC>;
+			clocks = <&vencsys CLK_VENC_SET1_VENC>;
+			clock-names = "venc-set1";
+			assigned-clocks = <&topckgen CLK_TOP_VENC_SEL>;
+			assigned-clock-parents = <&topckgen CLK_TOP_UNIVPLL_D4>;
+		};
+
 		camsys: clock-controller@1a000000 {
 			compatible = "mediatek,mt8192-camsys";
 			reg = <0 0x1a000000 0 0x1000>;
 			#clock-cells = <1>;
 		};
 
+		larb13: larb@1a001000 {
+			compatible = "mediatek,mt8192-smi-larb";
+			reg = <0 0x1a001000 0 0x1000>;
+			mediatek,larb-id = <13>;
+			mediatek,smi = <&smi_common>;
+			clocks = <&camsys CLK_CAM_CAM>,
+				 <&camsys CLK_CAM_LARB13>;
+			clock-names = "apb", "smi";
+			power-domains = <&spm MT8192_POWER_DOMAIN_CAM>;
+		};
+
+		larb14: larb@1a002000 {
+			compatible = "mediatek,mt8192-smi-larb";
+			reg = <0 0x1a002000 0 0x1000>;
+			mediatek,larb-id = <14>;
+			mediatek,smi = <&smi_common>;
+			clocks = <&camsys CLK_CAM_CAM>,
+				 <&camsys CLK_CAM_LARB14>;
+			clock-names = "apb", "smi";
+			power-domains = <&spm MT8192_POWER_DOMAIN_CAM>;
+		};
+
+		larb16: larb@1a00f000 {
+			compatible = "mediatek,mt8192-smi-larb";
+			reg = <0 0x1a00f000 0 0x1000>;
+			mediatek,larb-id = <16>;
+			mediatek,smi = <&smi_common>;
+			clocks = <&camsys_rawa CLK_CAM_RAWA_CAM>,
+				 <&camsys_rawa CLK_CAM_RAWA_LARBX>;
+			clock-names = "apb", "smi";
+			power-domains = <&spm MT8192_POWER_DOMAIN_CAM_RAWA>;
+		};
+
+		larb17: larb@1a010000 {
+			compatible = "mediatek,mt8192-smi-larb";
+			reg = <0 0x1a010000 0 0x1000>;
+			mediatek,larb-id = <17>;
+			mediatek,smi = <&smi_common>;
+			clocks = <&camsys_rawb CLK_CAM_RAWB_CAM>,
+				 <&camsys_rawb CLK_CAM_RAWB_LARBX>;
+			clock-names = "apb", "smi";
+			power-domains = <&spm MT8192_POWER_DOMAIN_CAM_RAWB>;
+		};
+
+		larb18: larb@1a011000 {
+			compatible = "mediatek,mt8192-smi-larb";
+			reg = <0 0x1a011000 0 0x1000>;
+			mediatek,larb-id = <18>;
+			mediatek,smi = <&smi_common>;
+			clocks = <&camsys_rawc CLK_CAM_RAWC_LARBX>,
+				 <&camsys_rawc CLK_CAM_RAWC_CAM>;
+			clock-names = "apb", "smi";
+			power-domains = <&spm MT8192_POWER_DOMAIN_CAM_RAWC>;
+		};
+
 		camsys_rawa: clock-controller@1a04f000 {
 			compatible = "mediatek,mt8192-camsys_rawa";
 			reg = <0 0x1a04f000 0 0x1000>;
@@ -723,10 +1608,43 @@
 			#clock-cells = <1>;
 		};
 
+		larb20: larb@1b00f000 {
+			compatible = "mediatek,mt8192-smi-larb";
+			reg = <0 0x1b00f000 0 0x1000>;
+			mediatek,larb-id = <20>;
+			mediatek,smi = <&smi_common>;
+			clocks = <&ipesys CLK_IPE_SMI_SUBCOM>,
+				 <&ipesys CLK_IPE_LARB20>;
+			clock-names = "apb", "smi";
+			power-domains = <&spm MT8192_POWER_DOMAIN_IPE>;
+		};
+
+		larb19: larb@1b10f000 {
+			compatible = "mediatek,mt8192-smi-larb";
+			reg = <0 0x1b10f000 0 0x1000>;
+			mediatek,larb-id = <19>;
+			mediatek,smi = <&smi_common>;
+			clocks = <&ipesys CLK_IPE_SMI_SUBCOM>,
+				 <&ipesys CLK_IPE_LARB19>;
+			clock-names = "apb", "smi";
+			power-domains = <&spm MT8192_POWER_DOMAIN_IPE>;
+		};
+
 		mdpsys: clock-controller@1f000000 {
 			compatible = "mediatek,mt8192-mdpsys";
 			reg = <0 0x1f000000 0 0x1000>;
 			#clock-cells = <1>;
 		};
+
+		larb2: larb@1f002000 {
+			compatible = "mediatek,mt8192-smi-larb";
+			reg = <0 0x1f002000 0 0x1000>;
+			mediatek,larb-id = <2>;
+			mediatek,smi = <&smi_common>;
+			clocks = <&mdpsys CLK_MDP_SMI0>,
+				 <&mdpsys CLK_MDP_SMI0>;
+			clock-names = "apb", "smi";
+			power-domains = <&spm MT8192_POWER_DOMAIN_MDP>;
+		};
 	};
 };
diff --git a/arch/arm64/boot/dts/mediatek/mt8195-cherry-tomato-r1.dts b/arch/arm64/boot/dts/mediatek/mt8195-cherry-tomato-r1.dts
new file mode 100644
index 000000000000..3348ba69ff6c
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt8195-cherry-tomato-r1.dts
@@ -0,0 +1,15 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright (C) 2021 MediaTek Inc.
+ */
+/dts-v1/;
+#include "mt8195-cherry.dtsi"
+
+/ {
+	model = "Acer Tomato (rev1) board";
+	compatible = "google,tomato-rev1", "google,tomato", "mediatek,mt8195";
+};
+
+&ts_10 {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/mediatek/mt8195-cherry-tomato-r2.dts b/arch/arm64/boot/dts/mediatek/mt8195-cherry-tomato-r2.dts
new file mode 100644
index 000000000000..4669e9d917f8
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt8195-cherry-tomato-r2.dts
@@ -0,0 +1,35 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright (C) 2021 MediaTek Inc.
+ */
+/dts-v1/;
+#include "mt8195-cherry.dtsi"
+
+/ {
+	model = "Acer Tomato (rev2) board";
+	compatible = "google,tomato-rev2", "google,tomato", "mediatek,mt8195";
+};
+
+&pio_default {
+	pins-low-power-hdmi-disable {
+		pinmux = <PINMUX_GPIO31__FUNC_GPIO31>,
+			 <PINMUX_GPIO32__FUNC_GPIO32>,
+			 <PINMUX_GPIO33__FUNC_GPIO33>,
+			 <PINMUX_GPIO34__FUNC_GPIO34>,
+			 <PINMUX_GPIO35__FUNC_GPIO35>;
+		input-enable;
+		bias-pull-down;
+	};
+
+	pins-low-power-pcie0-disable {
+		pinmux = <PINMUX_GPIO19__FUNC_GPIO19>,
+			 <PINMUX_GPIO20__FUNC_GPIO20>,
+			 <PINMUX_GPIO21__FUNC_GPIO21>;
+		input-enable;
+		bias-pull-down;
+	};
+};
+
+&ts_10 {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/mediatek/mt8195-cherry-tomato-r3.dts b/arch/arm64/boot/dts/mediatek/mt8195-cherry-tomato-r3.dts
new file mode 100644
index 000000000000..5021edd02f7c
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt8195-cherry-tomato-r3.dts
@@ -0,0 +1,36 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright (C) 2021 MediaTek Inc.
+ */
+/dts-v1/;
+#include "mt8195-cherry.dtsi"
+
+/ {
+	model = "Acer Tomato (rev3 - 4) board";
+	compatible = "google,tomato-rev4", "google,tomato-rev3",
+		     "google,tomato", "mediatek,mt8195";
+};
+
+&pio_default {
+	pins-low-power-hdmi-disable {
+		pinmux = <PINMUX_GPIO31__FUNC_GPIO31>,
+			 <PINMUX_GPIO32__FUNC_GPIO32>,
+			 <PINMUX_GPIO33__FUNC_GPIO33>,
+			 <PINMUX_GPIO34__FUNC_GPIO34>,
+			 <PINMUX_GPIO35__FUNC_GPIO35>;
+		input-enable;
+		bias-pull-down;
+	};
+
+	pins-low-power-pcie0-disable {
+		pinmux = <PINMUX_GPIO19__FUNC_GPIO19>,
+			 <PINMUX_GPIO20__FUNC_GPIO20>,
+			 <PINMUX_GPIO21__FUNC_GPIO21>;
+		input-enable;
+		bias-pull-down;
+	};
+};
+
+&ts_10 {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/mediatek/mt8195-cherry.dtsi b/arch/arm64/boot/dts/mediatek/mt8195-cherry.dtsi
new file mode 100644
index 000000000000..9b62e161db26
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt8195-cherry.dtsi
@@ -0,0 +1,958 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright (C) 2021 MediaTek Inc.
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/spmi/spmi.h>
+#include "mt8195.dtsi"
+#include "mt6359.dtsi"
+
+/ {
+	aliases {
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+		i2c2 = &i2c2;
+		i2c3 = &i2c3;
+		i2c4 = &i2c4;
+		i2c5 = &i2c5;
+		i2c7 = &i2c7;
+		mmc0 = &mmc0;
+		mmc1 = &mmc1;
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@40000000 {
+		device_type = "memory";
+		reg = <0 0x40000000 0 0x80000000>;
+	};
+
+	/* system wide LDO 3.3V power rail */
+	pp3300_z5: regulator-pp3300-ldo-z5 {
+		compatible = "regulator-fixed";
+		regulator-name = "pp3300_ldo_z5";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&ppvar_sys>;
+	};
+
+	/* separately switched 3.3V power rail */
+	pp3300_s3: regulator-pp3300-s3 {
+		compatible = "regulator-fixed";
+		regulator-name = "pp3300_s3";
+		/* automatically sequenced by PMIC EXT_PMIC_EN2 */
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&pp3300_z2>;
+	};
+
+	/* system wide 3.3V power rail */
+	pp3300_z2: regulator-pp3300-z2 {
+		compatible = "regulator-fixed";
+		regulator-name = "pp3300_z2";
+		/* EN pin tied to pp4200_z2, which is controlled by EC */
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&ppvar_sys>;
+	};
+
+	/* system wide 4.2V power rail */
+	pp4200_z2: regulator-pp4200-z2 {
+		compatible = "regulator-fixed";
+		regulator-name = "pp4200_z2";
+		/* controlled by EC */
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <4200000>;
+		regulator-max-microvolt = <4200000>;
+		vin-supply = <&ppvar_sys>;
+	};
+
+	/* system wide switching 5.0V power rail */
+	pp5000_s5: regulator-pp5000-s5 {
+		compatible = "regulator-fixed";
+		regulator-name = "pp5000_s5";
+		/* controlled by EC */
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&ppvar_sys>;
+	};
+
+	/* system wide semi-regulated power rail from battery or USB */
+	ppvar_sys: regulator-ppvar-sys {
+		compatible = "regulator-fixed";
+		regulator-name = "ppvar_sys";
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	usb_vbus: regulator-5v0-usb-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb-vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		regulator-always-on;
+	};
+
+	reserved_memory: reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		scp_mem: memory@50000000 {
+			compatible = "shared-dma-pool";
+			reg = <0 0x50000000 0 0x2900000>;
+			no-map;
+		};
+	};
+};
+
+&i2c0 {
+	status = "okay";
+
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins>;
+};
+
+&i2c1 {
+	status = "okay";
+
+	clock-frequency = <400000>;
+	i2c-scl-internal-delay-ns = <12500>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+
+	trackpad@15 {
+		compatible = "elan,ekth3000";
+		reg = <0x15>;
+		interrupts-extended = <&pio 6 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&trackpad_pins>;
+		vcc-supply = <&pp3300_s3>;
+		wakeup-source;
+	};
+};
+
+&i2c2 {
+	status = "okay";
+
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2_pins>;
+};
+
+&i2c3 {
+	status = "okay";
+
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c3_pins>;
+
+	tpm@50 {
+		compatible = "google,cr50";
+		reg = <0x50>;
+		interrupts-extended = <&pio 88 IRQ_TYPE_EDGE_FALLING>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&cr50_int>;
+	};
+};
+
+&i2c4 {
+	status = "okay";
+
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c4_pins>;
+
+	ts_10: touchscreen@10 {
+		compatible = "hid-over-i2c";
+		reg = <0x10>;
+		hid-descr-addr = <0x0001>;
+		interrupts-extended = <&pio 92 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&touchscreen_pins>;
+		post-power-on-delay-ms = <10>;
+		vdd-supply = <&pp3300_s3>;
+		status = "disabled";
+	};
+};
+
+&i2c5 {
+	status = "okay";
+
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c5_pins>;
+};
+
+&i2c7 {
+	status = "okay";
+
+	clock-frequency = <400000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c7_pins>;
+
+	pmic@34 {
+		#interrupt-cells = <1>;
+		compatible = "mediatek,mt6360";
+		reg = <0x34>;
+		interrupt-controller;
+		interrupts-extended = <&pio 130 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-names = "IRQB";
+		pinctrl-names = "default";
+		pinctrl-0 = <&subpmic_default>;
+		wakeup-source;
+	};
+};
+
+&mmc0 {
+	status = "okay";
+
+	bus-width = <8>;
+	cap-mmc-highspeed;
+	cap-mmc-hw-reset;
+	hs400-ds-delay = <0x14c11>;
+	max-frequency = <200000000>;
+	mmc-hs200-1_8v;
+	mmc-hs400-1_8v;
+	no-sdio;
+	no-sd;
+	non-removable;
+	pinctrl-names = "default", "state_uhs";
+	pinctrl-0 = <&mmc0_pins_default>;
+	pinctrl-1 = <&mmc0_pins_uhs>;
+	vmmc-supply = <&mt6359_vemc_1_ldo_reg>;
+	vqmmc-supply = <&mt6359_vufs_ldo_reg>;
+};
+
+&mmc1 {
+	status = "okay";
+
+	bus-width = <4>;
+	cap-sd-highspeed;
+	cd-gpios = <&pio 54 GPIO_ACTIVE_LOW>;
+	max-frequency = <200000000>;
+	no-mmc;
+	no-sdio;
+	pinctrl-names = "default", "state_uhs";
+	pinctrl-0 = <&mmc1_pins_default>, <&mmc1_pins_detect>;
+	pinctrl-1 = <&mmc1_pins_default>;
+	sd-uhs-sdr50;
+	sd-uhs-sdr104;
+	vmmc-supply = <&mt_pmic_vmch_ldo_reg>;
+	vqmmc-supply = <&mt_pmic_vmc_ldo_reg>;
+};
+
+/* for CPU-L */
+&mt6359_vcore_buck_reg {
+	regulator-always-on;
+};
+
+/* for CORE */
+&mt6359_vgpu11_buck_reg {
+	regulator-always-on;
+};
+
+&mt6359_vgpu11_sshub_buck_reg {
+	regulator-always-on;
+	regulator-min-microvolt = <550000>;
+	regulator-max-microvolt = <550000>;
+};
+
+/* for CORE SRAM */
+&mt6359_vpu_buck_reg {
+	regulator-always-on;
+};
+
+&mt6359_vrf12_ldo_reg {
+	regulator-always-on;
+};
+
+/* for GPU SRAM */
+&mt6359_vsram_others_ldo_reg {
+	regulator-always-on;
+	regulator-min-microvolt = <750000>;
+	regulator-max-microvolt = <750000>;
+};
+
+&mt6359_vufs_ldo_reg {
+	regulator-always-on;
+};
+
+&nor_flash {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&nor_pins_default>;
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <52000000>;
+		spi-rx-bus-width = <2>;
+		spi-tx-bus-width = <2>;
+	};
+};
+
+&pio {
+	mediatek,rsel-resistance-in-si-unit;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pio_default>;
+
+	/* 144 lines */
+	gpio-line-names =
+		"I2S_SPKR_MCLK",
+		"I2S_SPKR_DATAIN",
+		"I2S_SPKR_LRCK",
+		"I2S_SPKR_BCLK",
+		"EC_AP_INT_ODL",
+		/*
+		 * AP_FLASH_WP_L is crossystem ABI. Schematics
+		 * call it AP_FLASH_WP_ODL.
+		 */
+		"AP_FLASH_WP_L",
+		"TCHPAD_INT_ODL",
+		"EDP_HPD_1V8",
+		"AP_I2C_CAM_SDA",
+		"AP_I2C_CAM_SCL",
+		"AP_I2C_TCHPAD_SDA_1V8",
+		"AP_I2C_TCHPAD_SCL_1V8",
+		"AP_I2C_AUD_SDA",
+		"AP_I2C_AUD_SCL",
+		"AP_I2C_TPM_SDA_1V8",
+		"AP_I2C_TPM_SCL_1V8",
+		"AP_I2C_TCHSCR_SDA_1V8",
+		"AP_I2C_TCHSCR_SCL_1V8",
+		"EC_AP_HPD_OD",
+		"",
+		"PCIE_NVME_RST_L",
+		"PCIE_NVME_CLKREQ_ODL",
+		"PCIE_RST_1V8_L",
+		"PCIE_CLKREQ_1V8_ODL",
+		"PCIE_WAKE_1V8_ODL",
+		"CLK_24M_CAM0",
+		"CAM1_SEN_EN",
+		"AP_I2C_PWR_SCL_1V8",
+		"AP_I2C_PWR_SDA_1V8",
+		"AP_I2C_MISC_SCL",
+		"AP_I2C_MISC_SDA",
+		"EN_PP5000_HDMI_X",
+		"AP_HDMITX_HTPLG",
+		"",
+		"AP_HDMITX_SCL_1V8",
+		"AP_HDMITX_SDA_1V8",
+		"AP_RTC_CLK32K",
+		"AP_EC_WATCHDOG_L",
+		"SRCLKENA0",
+		"SRCLKENA1",
+		"PWRAP_SPI0_CS_L",
+		"PWRAP_SPI0_CK",
+		"PWRAP_SPI0_MOSI",
+		"PWRAP_SPI0_MISO",
+		"SPMI_SCL",
+		"SPMI_SDA",
+		"",
+		"",
+		"",
+		"I2S_HP_DATAIN",
+		"I2S_HP_MCLK",
+		"I2S_HP_BCK",
+		"I2S_HP_LRCK",
+		"I2S_HP_DATAOUT",
+		"SD_CD_ODL",
+		"EN_PP3300_DISP_X",
+		"TCHSCR_RST_1V8_L",
+		"TCHSCR_REPORT_DISABLE",
+		"EN_PP3300_WLAN_X",
+		"BT_KILL_1V8_L",
+		"I2S_SPKR_DATAOUT",
+		"WIFI_KILL_1V8_L",
+		"BEEP_ON",
+		"SCP_I2C_SENSOR_SCL_1V8",
+		"SCP_I2C_SENSOR_SDA_1V8",
+		"",
+		"",
+		"",
+		"",
+		"AUD_CLK_MOSI",
+		"AUD_SYNC_MOSI",
+		"AUD_DAT_MOSI0",
+		"AUD_DAT_MOSI1",
+		"AUD_DAT_MISO0",
+		"AUD_DAT_MISO1",
+		"AUD_DAT_MISO2",
+		"SCP_VREQ_VAO",
+		"AP_SPI_GSC_TPM_CLK",
+		"AP_SPI_GSC_TPM_MOSI",
+		"AP_SPI_GSC_TPM_CS_L",
+		"AP_SPI_GSC_TPM_MISO",
+		"EN_PP1000_CAM_X",
+		"AP_EDP_BKLTEN",
+		"",
+		"USB3_HUB_RST_L",
+		"",
+		"WLAN_ALERT_ODL",
+		"EC_IN_RW_ODL",
+		"GSC_AP_INT_ODL",
+		"HP_INT_ODL",
+		"CAM0_RST_L",
+		"CAM1_RST_L",
+		"TCHSCR_INT_1V8_L",
+		"CAM1_DET_L",
+		"RST_ALC1011_L",
+		"",
+		"",
+		"BL_PWM_1V8",
+		"UART_AP_TX_DBG_RX",
+		"UART_DBG_TX_AP_RX",
+		"EN_SPKR",
+		"AP_EC_WARM_RST_REQ",
+		"UART_SCP_TX_DBGCON_RX",
+		"UART_DBGCON_TX_SCP_RX",
+		"",
+		"",
+		"KPCOL0",
+		"",
+		"MT6315_GPU_INT",
+		"MT6315_PROC_BC_INT",
+		"SD_CMD",
+		"SD_CLK",
+		"SD_DAT0",
+		"SD_DAT1",
+		"SD_DAT2",
+		"SD_DAT3",
+		"EMMC_DAT7",
+		"EMMC_DAT6",
+		"EMMC_DAT5",
+		"EMMC_DAT4",
+		"EMMC_RSTB",
+		"EMMC_CMD",
+		"EMMC_CLK",
+		"EMMC_DAT3",
+		"EMMC_DAT2",
+		"EMMC_DAT1",
+		"EMMC_DAT0",
+		"EMMC_DSL",
+		"",
+		"",
+		"MT6360_INT_ODL",
+		"SCP_JTAG0_TRSTN",
+		"AP_SPI_EC_CS_L",
+		"AP_SPI_EC_CLK",
+		"AP_SPI_EC_MOSI",
+		"AP_SPI_EC_MISO",
+		"SCP_JTAG0_TMS",
+		"SCP_JTAG0_TCK",
+		"SCP_JTAG0_TDO",
+		"SCP_JTAG0_TDI",
+		"AP_SPI_FLASH_CS_L",
+		"AP_SPI_FLASH_CLK",
+		"AP_SPI_FLASH_MOSI",
+		"AP_SPI_FLASH_MISO";
+
+	cr50_int: cr50-irq-default-pins {
+		pins-gsc-ap-int-odl {
+			pinmux = <PINMUX_GPIO88__FUNC_GPIO88>;
+			input-enable;
+		};
+	};
+
+	cros_ec_int: cros-ec-irq-default-pins {
+		pins-ec-ap-int-odl {
+			pinmux = <PINMUX_GPIO4__FUNC_GPIO4>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+			input-enable;
+		};
+	};
+
+	i2c0_pins: i2c0-default-pins {
+		pins-bus {
+			pinmux = <PINMUX_GPIO8__FUNC_SDA0>,
+				 <PINMUX_GPIO9__FUNC_SCL0>;
+			bias-disable;
+			drive-strength-microamp = <1000>;
+		};
+	};
+
+	i2c1_pins: i2c1-default-pins {
+		pins-bus {
+			pinmux = <PINMUX_GPIO10__FUNC_SDA1>,
+				 <PINMUX_GPIO11__FUNC_SCL1>;
+			bias-pull-up = <1000>;
+			drive-strength-microamp = <1000>;
+		};
+	};
+
+	i2c2_pins: i2c2-default-pins {
+		pins-bus {
+			pinmux = <PINMUX_GPIO12__FUNC_SDA2>,
+				 <PINMUX_GPIO13__FUNC_SCL2>;
+			bias-disable;
+			drive-strength-microamp = <1000>;
+		};
+	};
+
+	i2c3_pins: i2c3-default-pins {
+		pins-bus {
+			pinmux = <PINMUX_GPIO14__FUNC_SDA3>,
+				 <PINMUX_GPIO15__FUNC_SCL3>;
+			bias-pull-up = <1000>;
+			drive-strength-microamp = <1000>;
+		};
+	};
+
+	i2c4_pins: i2c4-default-pins {
+		pins-bus {
+			pinmux = <PINMUX_GPIO16__FUNC_SDA4>,
+				 <PINMUX_GPIO17__FUNC_SCL4>;
+			bias-pull-up = <1000>;
+			drive-strength = <4>;
+		};
+	};
+
+	i2c5_pins: i2c5-default-pins {
+		pins-bus {
+			pinmux = <PINMUX_GPIO29__FUNC_SCL5>,
+				 <PINMUX_GPIO30__FUNC_SDA5>;
+			bias-disable;
+			drive-strength-microamp = <1000>;
+		};
+	};
+
+	i2c7_pins: i2c7-default-pins {
+		pins-bus {
+			pinmux = <PINMUX_GPIO27__FUNC_SCL7>,
+				 <PINMUX_GPIO28__FUNC_SDA7>;
+			bias-disable;
+		};
+	};
+
+	mmc0_pins_default: mmc0-default-pins {
+		pins-cmd-dat {
+			pinmux = <PINMUX_GPIO126__FUNC_MSDC0_DAT0>,
+				 <PINMUX_GPIO125__FUNC_MSDC0_DAT1>,
+				 <PINMUX_GPIO124__FUNC_MSDC0_DAT2>,
+				 <PINMUX_GPIO123__FUNC_MSDC0_DAT3>,
+				 <PINMUX_GPIO119__FUNC_MSDC0_DAT4>,
+				 <PINMUX_GPIO118__FUNC_MSDC0_DAT5>,
+				 <PINMUX_GPIO117__FUNC_MSDC0_DAT6>,
+				 <PINMUX_GPIO116__FUNC_MSDC0_DAT7>,
+				 <PINMUX_GPIO121__FUNC_MSDC0_CMD>;
+			input-enable;
+			drive-strength = <6>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+		};
+
+		pins-clk {
+			pinmux = <PINMUX_GPIO122__FUNC_MSDC0_CLK>;
+			drive-strength = <6>;
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
+		};
+
+		pins-rst {
+			pinmux = <PINMUX_GPIO120__FUNC_MSDC0_RSTB>;
+			drive-strength = <6>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+		};
+	};
+
+	mmc0_pins_uhs: mmc0-uhs-pins {
+		pins-cmd-dat {
+			pinmux = <PINMUX_GPIO126__FUNC_MSDC0_DAT0>,
+				 <PINMUX_GPIO125__FUNC_MSDC0_DAT1>,
+				 <PINMUX_GPIO124__FUNC_MSDC0_DAT2>,
+				 <PINMUX_GPIO123__FUNC_MSDC0_DAT3>,
+				 <PINMUX_GPIO119__FUNC_MSDC0_DAT4>,
+				 <PINMUX_GPIO118__FUNC_MSDC0_DAT5>,
+				 <PINMUX_GPIO117__FUNC_MSDC0_DAT6>,
+				 <PINMUX_GPIO116__FUNC_MSDC0_DAT7>,
+				 <PINMUX_GPIO121__FUNC_MSDC0_CMD>;
+			input-enable;
+			drive-strength = <8>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+		};
+
+		pins-clk {
+			pinmux = <PINMUX_GPIO122__FUNC_MSDC0_CLK>;
+			drive-strength = <8>;
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
+		};
+
+		pins-ds {
+			pinmux = <PINMUX_GPIO127__FUNC_MSDC0_DSL>;
+			drive-strength = <8>;
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
+		};
+
+		pins-rst {
+			pinmux = <PINMUX_GPIO120__FUNC_MSDC0_RSTB>;
+			drive-strength = <8>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+		};
+	};
+
+	mmc1_pins_detect: mmc1-detect-pins {
+		pins-insert {
+			pinmux = <PINMUX_GPIO54__FUNC_GPIO54>;
+			bias-pull-up;
+		};
+	};
+
+	mmc1_pins_default: mmc1-default-pins {
+		pins-cmd-dat {
+			pinmux = <PINMUX_GPIO110__FUNC_MSDC1_CMD>,
+				 <PINMUX_GPIO112__FUNC_MSDC1_DAT0>,
+				 <PINMUX_GPIO113__FUNC_MSDC1_DAT1>,
+				 <PINMUX_GPIO114__FUNC_MSDC1_DAT2>,
+				 <PINMUX_GPIO115__FUNC_MSDC1_DAT3>;
+			input-enable;
+			drive-strength = <8>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+		};
+
+		pins-clk {
+			pinmux = <PINMUX_GPIO111__FUNC_MSDC1_CLK>;
+			drive-strength = <8>;
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
+		};
+	};
+
+	nor_pins_default: nor-default-pins {
+		pins-ck-io {
+			pinmux = <PINMUX_GPIO142__FUNC_SPINOR_IO0>,
+				 <PINMUX_GPIO141__FUNC_SPINOR_CK>,
+				 <PINMUX_GPIO143__FUNC_SPINOR_IO1>;
+			drive-strength = <6>;
+			bias-pull-down;
+		};
+
+		pins-cs {
+			pinmux = <PINMUX_GPIO140__FUNC_SPINOR_CS>;
+			drive-strength = <6>;
+			bias-pull-up;
+		};
+	};
+
+	pio_default: pio-default-pins {
+		pins-wifi-enable {
+			pinmux = <PINMUX_GPIO58__FUNC_GPIO58>;
+			output-high;
+			drive-strength = <14>;
+		};
+
+		pins-low-power-pd {
+			pinmux = <PINMUX_GPIO25__FUNC_GPIO25>,
+				 <PINMUX_GPIO26__FUNC_GPIO26>,
+				 <PINMUX_GPIO46__FUNC_GPIO46>,
+				 <PINMUX_GPIO47__FUNC_GPIO47>,
+				 <PINMUX_GPIO48__FUNC_GPIO48>,
+				 <PINMUX_GPIO65__FUNC_GPIO65>,
+				 <PINMUX_GPIO66__FUNC_GPIO66>,
+				 <PINMUX_GPIO67__FUNC_GPIO67>,
+				 <PINMUX_GPIO68__FUNC_GPIO68>,
+				 <PINMUX_GPIO128__FUNC_GPIO128>,
+				 <PINMUX_GPIO129__FUNC_GPIO129>;
+			input-enable;
+			bias-pull-down;
+		};
+
+		pins-low-power-pupd {
+			pinmux = <PINMUX_GPIO77__FUNC_GPIO77>,
+				 <PINMUX_GPIO78__FUNC_GPIO78>,
+				 <PINMUX_GPIO79__FUNC_GPIO79>,
+				 <PINMUX_GPIO80__FUNC_GPIO80>,
+				 <PINMUX_GPIO83__FUNC_GPIO83>,
+				 <PINMUX_GPIO85__FUNC_GPIO85>,
+				 <PINMUX_GPIO90__FUNC_GPIO90>,
+				 <PINMUX_GPIO91__FUNC_GPIO91>,
+				 <PINMUX_GPIO93__FUNC_GPIO93>,
+				 <PINMUX_GPIO94__FUNC_GPIO94>,
+				 <PINMUX_GPIO95__FUNC_GPIO95>,
+				 <PINMUX_GPIO96__FUNC_GPIO96>,
+				 <PINMUX_GPIO104__FUNC_GPIO104>,
+				 <PINMUX_GPIO105__FUNC_GPIO105>,
+				 <PINMUX_GPIO107__FUNC_GPIO107>;
+			input-enable;
+			bias-pull-down = <MTK_PUPD_SET_R1R0_01>;
+		};
+	};
+
+	scp_pins: scp-default-pins {
+		pins-vreq {
+			pinmux = <PINMUX_GPIO76__FUNC_SCP_VREQ_VAO>;
+			bias-disable;
+			input-enable;
+		};
+	};
+
+	spi0_pins: spi0-default-pins {
+		pins-cs-mosi-clk {
+			pinmux = <PINMUX_GPIO132__FUNC_SPIM0_CSB>,
+				 <PINMUX_GPIO134__FUNC_SPIM0_MO>,
+				 <PINMUX_GPIO133__FUNC_SPIM0_CLK>;
+			bias-disable;
+		};
+
+		pins-miso {
+			pinmux = <PINMUX_GPIO135__FUNC_SPIM0_MI>;
+			bias-pull-down;
+		};
+	};
+
+	subpmic_default: subpmic-default-pins {
+		subpmic_pin_irq: pins-subpmic-int-n {
+			pinmux = <PINMUX_GPIO130__FUNC_GPIO130>;
+			input-enable;
+			bias-pull-up;
+		};
+	};
+
+	trackpad_pins: trackpad-default-pins {
+		pins-int-n {
+			pinmux = <PINMUX_GPIO6__FUNC_GPIO6>;
+			input-enable;
+			bias-pull-up;
+		};
+	};
+
+	touchscreen_pins: touchscreen-default-pins {
+		pins-int-n {
+			pinmux = <PINMUX_GPIO92__FUNC_GPIO92>;
+			input-enable;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+		};
+		pins-rst {
+			pinmux = <PINMUX_GPIO56__FUNC_GPIO56>;
+			output-high;
+		};
+		pins-report-sw {
+			pinmux = <PINMUX_GPIO57__FUNC_GPIO57>;
+			output-low;
+		};
+	};
+};
+
+&pmic {
+	interrupts-extended = <&pio 222 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&scp {
+	status = "okay";
+
+	firmware-name = "mediatek/mt8195/scp.img";
+	memory-region = <&scp_mem>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&scp_pins>;
+
+	cros-ec-rpmsg {
+		compatible = "google,cros-ec-rpmsg";
+		mediatek,rpmsg-name = "cros-ec-rpmsg";
+	};
+};
+
+&spi0 {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_pins>;
+	mediatek,pad-select = <0>;
+
+	cros_ec: ec@0 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		compatible = "google,cros-ec-spi";
+		reg = <0>;
+		interrupts-extended = <&pio 4 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&cros_ec_int>;
+		spi-max-frequency = <3000000>;
+
+		keyboard-backlight {
+			compatible = "google,cros-kbd-led-backlight";
+		};
+
+		i2c_tunnel: i2c-tunnel {
+			compatible = "google,cros-ec-i2c-tunnel";
+			google,remote-bus = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		mt_pmic_vmc_ldo_reg: regulator@0 {
+			compatible = "google,cros-ec-regulator";
+			reg = <0>;
+			regulator-name = "mt_pmic_vmc_ldo";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <3600000>;
+		};
+
+		mt_pmic_vmch_ldo_reg: regulator@1 {
+			compatible = "google,cros-ec-regulator";
+			reg = <1>;
+			regulator-name = "mt_pmic_vmch_ldo";
+			regulator-min-microvolt = <2700000>;
+			regulator-max-microvolt = <3600000>;
+		};
+
+		typec {
+			compatible = "google,cros-ec-typec";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			usb_c0: connector@0 {
+				compatible = "usb-c-connector";
+				reg = <0>;
+				power-role = "dual";
+				data-role = "host";
+				try-power-role = "source";
+			};
+
+			usb_c1: connector@1 {
+				compatible = "usb-c-connector";
+				reg = <1>;
+				power-role = "dual";
+				data-role = "host";
+				try-power-role = "source";
+			};
+		};
+	};
+};
+
+&spmi {
+	#address-cells = <2>;
+	#size-cells = <0>;
+
+	mt6315@6 {
+		compatible = "mediatek,mt6315-regulator";
+		reg = <0x6 SPMI_USID>;
+
+		regulators {
+			mt6315_6_vbuck1: vbuck1 {
+				regulator-compatible = "vbuck1";
+				regulator-name = "Vbcpu";
+				regulator-min-microvolt = <300000>;
+				regulator-max-microvolt = <1193750>;
+				regulator-enable-ramp-delay = <256>;
+				regulator-ramp-delay = <6250>;
+				regulator-allowed-modes = <0 1 2>;
+				regulator-always-on;
+			};
+		};
+	};
+
+	mt6315@7 {
+		compatible = "mediatek,mt6315-regulator";
+		reg = <0x7 SPMI_USID>;
+
+		regulators {
+			mt6315_7_vbuck1: vbuck1 {
+				regulator-compatible = "vbuck1";
+				regulator-name = "Vgpu";
+				regulator-min-microvolt = <625000>;
+				regulator-max-microvolt = <1193750>;
+				regulator-enable-ramp-delay = <256>;
+				regulator-ramp-delay = <6250>;
+				regulator-allowed-modes = <0 1 2>;
+				regulator-always-on;
+			};
+		};
+	};
+};
+
+&u3phy0 {
+	status = "okay";
+};
+
+&u3phy1 {
+	status = "okay";
+};
+
+&u3phy2 {
+	status = "okay";
+};
+
+&u3phy3 {
+	status = "okay";
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&xhci0 {
+	status = "okay";
+
+	vusb33-supply = <&mt6359_vusb_ldo_reg>;
+	vbus-supply = <&usb_vbus>;
+};
+
+&xhci1 {
+	status = "okay";
+
+	vusb33-supply = <&mt6359_vusb_ldo_reg>;
+	vbus-supply = <&usb_vbus>;
+};
+
+&xhci2 {
+	status = "okay";
+
+	vusb33-supply = <&mt6359_vusb_ldo_reg>;
+	vbus-supply = <&usb_vbus>;
+};
+
+&xhci3 {
+	status = "okay";
+
+	/* MT7921's USB Bluetooth has issues with USB2 LPM */
+	usb2-lpm-disable;
+	vusb33-supply = <&mt6359_vusb_ldo_reg>;
+	vbus-supply = <&usb_vbus>;
+};
+
+#include <arm/cros-ec-keyboard.dtsi>
+#include <arm/cros-ec-sbs.dtsi>
+
+&keyboard_controller {
+	function-row-physmap = <
+		MATRIX_KEY(0x00, 0x02, 0)	/* T1 */
+		MATRIX_KEY(0x03, 0x02, 0)	/* T2 */
+		MATRIX_KEY(0x02, 0x02, 0)	/* T3 */
+		MATRIX_KEY(0x01, 0x02, 0)	/* T4 */
+		MATRIX_KEY(0x03, 0x04, 0)	/* T5 */
+		MATRIX_KEY(0x02, 0x04, 0)	/* T6 */
+		MATRIX_KEY(0x01, 0x04, 0)	/* T7 */
+		MATRIX_KEY(0x02, 0x09, 0)	/* T8 */
+		MATRIX_KEY(0x01, 0x09, 0)	/* T9 */
+		MATRIX_KEY(0x00, 0x04, 0)	/* T10 */
+	>;
+
+	linux,keymap = <
+		MATRIX_KEY(0x00, 0x02, KEY_BACK)
+		MATRIX_KEY(0x03, 0x02, KEY_REFRESH)
+		MATRIX_KEY(0x02, 0x02, KEY_ZOOM)
+		MATRIX_KEY(0x01, 0x02, KEY_SCALE)
+		MATRIX_KEY(0x03, 0x04, KEY_SYSRQ)
+		MATRIX_KEY(0x02, 0x04, KEY_BRIGHTNESSDOWN)
+		MATRIX_KEY(0x01, 0x04, KEY_BRIGHTNESSUP)
+		MATRIX_KEY(0x02, 0x09, KEY_MUTE)
+		MATRIX_KEY(0x01, 0x09, KEY_VOLUMEDOWN)
+		MATRIX_KEY(0x00, 0x04, KEY_VOLUMEUP)
+
+		CROS_STD_MAIN_KEYMAP
+	>;
+};
diff --git a/arch/arm64/boot/dts/mediatek/mt8195-demo.dts b/arch/arm64/boot/dts/mediatek/mt8195-demo.dts
new file mode 100644
index 000000000000..4fbd99eb496a
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt8195-demo.dts
@@ -0,0 +1,450 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright (C) 2022 BayLibre, SAS.
+ * Author: Fabien Parent <fparent@baylibre.com>
+ */
+/dts-v1/;
+
+#include "mt8195.dtsi"
+#include "mt6359.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/mt8195-pinfunc.h>
+#include <dt-bindings/regulator/mediatek,mt6360-regulator.h>
+
+/ {
+	model = "MediaTek MT8195 demo board";
+	compatible = "mediatek,mt8195-demo", "mediatek,mt8195";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:921600n8";
+	};
+
+	firmware {
+		optee {
+			compatible = "linaro,optee-tz";
+			method = "smc";
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_keys_pins>;
+
+		key-0 {
+			gpios = <&pio 106 GPIO_ACTIVE_LOW>;
+			label = "volume_up";
+			linux,code = <KEY_VOLUMEUP>;
+			wakeup-source;
+			debounce-interval = <15>;
+		};
+	};
+
+	memory@40000000 {
+		device_type = "memory";
+		reg = <0 0x40000000 0 0x80000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		/* 192 KiB reserved for ARM Trusted Firmware (BL31) */
+		bl31_secmon_reserved: secmon@54600000 {
+			no-map;
+			reg = <0 0x54600000 0x0 0x30000>;
+		};
+
+		/* 12 MiB reserved for OP-TEE (BL32)
+		 * +-----------------------+ 0x43e0_0000
+		 * |      SHMEM 2MiB       |
+		 * +-----------------------+ 0x43c0_0000
+		 * |        | TA_RAM  8MiB |
+		 * + TZDRAM +--------------+ 0x4340_0000
+		 * |        | TEE_RAM 2MiB |
+		 * +-----------------------+ 0x4320_0000
+		 */
+		optee_reserved: optee@43200000 {
+			no-map;
+			reg = <0 0x43200000 0 0x00c00000>;
+		};
+	};
+};
+
+&i2c6 {
+	clock-frequency = <400000>;
+	pinctrl-0 = <&i2c6_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	mt6360: pmic@34 {
+		compatible = "mediatek,mt6360";
+		reg = <0x34>;
+		interrupt-controller;
+		interrupts-extended = <&pio 101 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-names = "IRQB";
+
+		charger {
+			compatible = "mediatek,mt6360-chg";
+			richtek,vinovp-microvolt = <14500000>;
+
+			otg_vbus_regulator: usb-otg-vbus-regulator {
+				regulator-compatible = "usb-otg-vbus";
+				regulator-name = "usb-otg-vbus";
+				regulator-min-microvolt = <4425000>;
+				regulator-max-microvolt = <5825000>;
+			};
+		};
+
+		regulator {
+			compatible = "mediatek,mt6360-regulator";
+			LDO_VIN3-supply = <&mt6360_buck2>;
+
+			mt6360_buck1: buck1 {
+				regulator-compatible = "BUCK1";
+				regulator-name = "mt6360,buck1";
+				regulator-min-microvolt = <300000>;
+				regulator-max-microvolt = <1300000>;
+				regulator-allowed-modes = <MT6360_OPMODE_NORMAL
+							   MT6360_OPMODE_LP
+							   MT6360_OPMODE_ULP>;
+				regulator-always-on;
+			};
+
+			mt6360_buck2: buck2 {
+				regulator-compatible = "BUCK2";
+				regulator-name = "mt6360,buck2";
+				regulator-min-microvolt = <300000>;
+				regulator-max-microvolt = <1300000>;
+				regulator-allowed-modes = <MT6360_OPMODE_NORMAL
+							   MT6360_OPMODE_LP
+							   MT6360_OPMODE_ULP>;
+				regulator-always-on;
+			};
+
+			mt6360_ldo1: ldo1 {
+				regulator-compatible = "LDO1";
+				regulator-name = "mt6360,ldo1";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <3600000>;
+				regulator-allowed-modes = <MT6360_OPMODE_NORMAL
+							   MT6360_OPMODE_LP>;
+			};
+
+			mt6360_ldo2: ldo2 {
+				regulator-compatible = "LDO2";
+				regulator-name = "mt6360,ldo2";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <3600000>;
+				regulator-allowed-modes = <MT6360_OPMODE_NORMAL
+							   MT6360_OPMODE_LP>;
+			};
+
+			mt6360_ldo3: ldo3 {
+				regulator-compatible = "LDO3";
+				regulator-name = "mt6360,ldo3";
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <3600000>;
+				regulator-allowed-modes = <MT6360_OPMODE_NORMAL
+							   MT6360_OPMODE_LP>;
+			};
+
+			mt6360_ldo5: ldo5 {
+				regulator-compatible = "LDO5";
+				regulator-name = "mt6360,ldo5";
+				regulator-min-microvolt = <2700000>;
+				regulator-max-microvolt = <3600000>;
+				regulator-allowed-modes = <MT6360_OPMODE_NORMAL
+							   MT6360_OPMODE_LP>;
+			};
+
+			mt6360_ldo6: ldo6 {
+				regulator-compatible = "LDO6";
+				regulator-name = "mt6360,ldo6";
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <2100000>;
+				regulator-allowed-modes = <MT6360_OPMODE_NORMAL
+							   MT6360_OPMODE_LP>;
+			};
+
+			mt6360_ldo7: ldo7 {
+				regulator-compatible = "LDO7";
+				regulator-name = "mt6360,ldo7";
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <2100000>;
+				regulator-allowed-modes = <MT6360_OPMODE_NORMAL
+							   MT6360_OPMODE_LP>;
+				regulator-always-on;
+			};
+		};
+	};
+};
+
+&mmc0 {
+	status = "okay";
+	pinctrl-names = "default", "state_uhs";
+	pinctrl-0 = <&mmc0_default_pins>;
+	pinctrl-1 = <&mmc0_uhs_pins>;
+	bus-width = <8>;
+	max-frequency = <200000000>;
+	cap-mmc-highspeed;
+	mmc-hs200-1_8v;
+	mmc-hs400-1_8v;
+	cap-mmc-hw-reset;
+	no-sdio;
+	no-sd;
+	hs400-ds-delay = <0x14c11>;
+	vmmc-supply = <&mt6359_vemc_1_ldo_reg>;
+	vqmmc-supply = <&mt6359_vufs_ldo_reg>;
+	non-removable;
+};
+
+&mmc1 {
+	pinctrl-names = "default", "state_uhs";
+	pinctrl-0 = <&mmc1_default_pins>;
+	pinctrl-1 = <&mmc1_uhs_pins>;
+	cd-gpios = <&pio 129 GPIO_ACTIVE_LOW>;
+	bus-width = <4>;
+	max-frequency = <200000000>;
+	cap-sd-highspeed;
+	sd-uhs-sdr50;
+	sd-uhs-sdr104;
+	vmmc-supply = <&mt6360_ldo5>;
+	vqmmc-supply = <&mt6360_ldo3>;
+	status = "okay";
+};
+
+&mt6359_vbbck_ldo_reg {
+	regulator-always-on;
+};
+
+&mt6359_vcore_buck_reg {
+	regulator-always-on;
+};
+
+&mt6359_vgpu11_buck_reg {
+	regulator-always-on;
+};
+
+&mt6359_vproc1_buck_reg {
+	regulator-always-on;
+};
+
+&mt6359_vproc2_buck_reg {
+	regulator-always-on;
+};
+
+&mt6359_vpu_buck_reg {
+	regulator-always-on;
+};
+
+&mt6359_vrf12_ldo_reg {
+	regulator-always-on;
+};
+
+&mt6359_vsram_md_ldo_reg {
+	regulator-always-on;
+};
+
+&mt6359_vsram_others_ldo_reg {
+	regulator-always-on;
+};
+
+&pio {
+	gpio_keys_pins: gpio-keys-pins {
+		pins {
+			pinmux = <PINMUX_GPIO106__FUNC_GPIO106>;
+			input-enable;
+		};
+	};
+
+	i2c6_pins: i2c6-pins {
+		pins {
+			pinmux = <PINMUX_GPIO25__FUNC_SDA6>,
+				 <PINMUX_GPIO26__FUNC_SCL6>;
+			bias-pull-up;
+		};
+	};
+
+	mmc0_default_pins: mmc0-default-pins {
+		pins-clk {
+			pinmux = <PINMUX_GPIO122__FUNC_MSDC0_CLK>;
+			drive-strength = <MTK_DRIVE_6mA>;
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
+		};
+
+		pins-cmd-dat {
+			pinmux = <PINMUX_GPIO126__FUNC_MSDC0_DAT0>,
+				 <PINMUX_GPIO125__FUNC_MSDC0_DAT1>,
+				 <PINMUX_GPIO124__FUNC_MSDC0_DAT2>,
+				 <PINMUX_GPIO123__FUNC_MSDC0_DAT3>,
+				 <PINMUX_GPIO119__FUNC_MSDC0_DAT4>,
+				 <PINMUX_GPIO118__FUNC_MSDC0_DAT5>,
+				 <PINMUX_GPIO117__FUNC_MSDC0_DAT6>,
+				 <PINMUX_GPIO116__FUNC_MSDC0_DAT7>,
+				 <PINMUX_GPIO121__FUNC_MSDC0_CMD>;
+			input-enable;
+			drive-strength = <MTK_DRIVE_6mA>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+		};
+
+		pins-rst {
+			pinmux = <PINMUX_GPIO120__FUNC_MSDC0_RSTB>;
+			drive-strength = <MTK_DRIVE_6mA>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+		};
+	};
+
+	mmc0_uhs_pins: mmc0-uhs-pins {
+		pins-clk {
+			pinmux = <PINMUX_GPIO122__FUNC_MSDC0_CLK>;
+			drive-strength = <MTK_DRIVE_8mA>;
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
+		};
+
+		pins-cmd-dat {
+			pinmux = <PINMUX_GPIO126__FUNC_MSDC0_DAT0>,
+				 <PINMUX_GPIO125__FUNC_MSDC0_DAT1>,
+				 <PINMUX_GPIO124__FUNC_MSDC0_DAT2>,
+				 <PINMUX_GPIO123__FUNC_MSDC0_DAT3>,
+				 <PINMUX_GPIO119__FUNC_MSDC0_DAT4>,
+				 <PINMUX_GPIO118__FUNC_MSDC0_DAT5>,
+				 <PINMUX_GPIO117__FUNC_MSDC0_DAT6>,
+				 <PINMUX_GPIO116__FUNC_MSDC0_DAT7>,
+				 <PINMUX_GPIO121__FUNC_MSDC0_CMD>;
+			input-enable;
+			drive-strength = <MTK_DRIVE_8mA>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+		};
+
+		pins-ds {
+			pinmux = <PINMUX_GPIO127__FUNC_MSDC0_DSL>;
+			drive-strength = <MTK_DRIVE_8mA>;
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
+		};
+
+		pins-rst {
+			pinmux = <PINMUX_GPIO120__FUNC_MSDC0_RSTB>;
+			drive-strength = <MTK_DRIVE_8mA>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+		};
+	};
+
+	mmc1_default_pins: mmc1-default-pins {
+		pins-clk {
+			pinmux = <PINMUX_GPIO111__FUNC_MSDC1_CLK>;
+			drive-strength = <MTK_DRIVE_8mA>;
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
+		};
+
+		pins-cmd-dat {
+			pinmux = <PINMUX_GPIO110__FUNC_MSDC1_CMD>,
+				 <PINMUX_GPIO112__FUNC_MSDC1_DAT0>,
+				 <PINMUX_GPIO113__FUNC_MSDC1_DAT1>,
+				 <PINMUX_GPIO114__FUNC_MSDC1_DAT2>,
+				 <PINMUX_GPIO115__FUNC_MSDC1_DAT3>;
+			input-enable;
+			drive-strength = <MTK_DRIVE_8mA>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+		};
+
+		pins-insert {
+			pinmux = <PINMUX_GPIO129__FUNC_GPIO129>;
+			bias-pull-up;
+		};
+	};
+
+	mmc1_uhs_pins: mmc1-uhs-pins {
+		pins-clk {
+			pinmux = <PINMUX_GPIO111__FUNC_MSDC1_CLK>;
+			drive-strength = <MTK_DRIVE_8mA>;
+			bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
+		};
+
+		pins-cmd-dat {
+			pinmux = <PINMUX_GPIO110__FUNC_MSDC1_CMD>,
+				 <PINMUX_GPIO112__FUNC_MSDC1_DAT0>,
+				 <PINMUX_GPIO113__FUNC_MSDC1_DAT1>,
+				 <PINMUX_GPIO114__FUNC_MSDC1_DAT2>,
+				 <PINMUX_GPIO115__FUNC_MSDC1_DAT3>;
+			input-enable;
+			drive-strength = <MTK_DRIVE_8mA>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+		};
+	};
+
+	uart0_pins: uart0-pins {
+		pins {
+			pinmux = <PINMUX_GPIO98__FUNC_UTXD0>,
+				 <PINMUX_GPIO99__FUNC_URXD0>;
+		};
+	};
+
+	uart1_pins: uart1-pins {
+		pins {
+			pinmux = <PINMUX_GPIO102__FUNC_UTXD1>,
+				 <PINMUX_GPIO103__FUNC_URXD1>;
+		};
+	};
+};
+
+
+&pmic {
+	interrupts-extended = <&pio 222 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins>;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>;
+	status = "okay";
+};
+
+&u3phy0 {
+	status = "okay";
+};
+
+&u3phy1 {
+	status = "okay";
+};
+
+&u3phy2 {
+	status = "okay";
+};
+
+&u3phy3 {
+	status = "okay";
+};
+
+&xhci0 {
+	vusb33-supply = <&mt6359_vusb_ldo_reg>;
+	vbus-supply = <&otg_vbus_regulator>;
+	status = "okay";
+};
+
+&xhci1 {
+	vusb33-supply = <&mt6359_vusb_ldo_reg>;
+	status = "okay";
+};
+
+&xhci2 {
+	vusb33-supply = <&mt6359_vusb_ldo_reg>;
+	status = "okay";
+};
+
+&xhci3 {
+	vusb33-supply = <&mt6359_vusb_ldo_reg>;
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/mediatek/mt8195-evb.dts b/arch/arm64/boot/dts/mediatek/mt8195-evb.dts
new file mode 100644
index 000000000000..690dc7717f2c
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt8195-evb.dts
@@ -0,0 +1,181 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright (C) 2021 MediaTek Inc.
+ * Author: Seiya Wang <seiya.wang@mediatek.com>
+ */
+/dts-v1/;
+#include "mt8195.dtsi"
+
+/ {
+	model = "MediaTek MT8195 evaluation board";
+	compatible = "mediatek,mt8195-evb", "mediatek,mt8195";
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:921600n8";
+	};
+
+	memory@40000000 {
+		device_type = "memory";
+		reg = <0 0x40000000 0 0x80000000>;
+	};
+};
+
+&auxadc {
+	status = "okay";
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pin>;
+	clock-frequency = <100000>;
+	status = "okay";
+};
+
+&i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pin>;
+	clock-frequency = <400000>;
+	status = "okay";
+};
+
+&i2c4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c4_pin>;
+	clock-frequency = <400000>;
+	status = "okay";
+};
+
+&i2c6 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c6_pin>;
+	clock-frequency = <400000>;
+	status = "okay";
+};
+
+&nor_flash {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&nor_pins_default>;
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <50000000>;
+	};
+};
+
+&pio {
+	i2c0_pin: i2c0-pins {
+		pins {
+			pinmux = <PINMUX_GPIO8__FUNC_SDA0>,
+				 <PINMUX_GPIO9__FUNC_SCL0>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+			mediatek,drive-strength-adv = <0>;
+			drive-strength = <6>;
+		};
+	};
+
+	i2c1_pin: i2c1-pins {
+		pins {
+			pinmux = <PINMUX_GPIO10__FUNC_SDA1>,
+				 <PINMUX_GPIO11__FUNC_SCL1>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+			mediatek,drive-strength-adv = <0>;
+			drive-strength = <6>;
+		};
+	};
+
+	i2c4_pin: i2c4-pins {
+		pins {
+			pinmux = <PINMUX_GPIO16__FUNC_SDA4>,
+				 <PINMUX_GPIO17__FUNC_SCL4>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+			mediatek,drive-strength-adv = <7>;
+		};
+	};
+
+	i2c6_pin: i2c6-pins {
+		pins {
+			pinmux = <PINMUX_GPIO25__FUNC_SDA6>,
+				 <PINMUX_GPIO26__FUNC_SCL6>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+		};
+	};
+
+	i2c7_pin: i2c7-pins {
+		pins {
+			pinmux = <PINMUX_GPIO27__FUNC_SCL7>,
+				 <PINMUX_GPIO28__FUNC_SDA7>;
+			bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
+		};
+	};
+
+	nor_pins_default: nor-pins {
+		pins0 {
+			pinmux = <PINMUX_GPIO142__FUNC_SPINOR_IO0>,
+				 <PINMUX_GPIO141__FUNC_SPINOR_CK>,
+				 <PINMUX_GPIO143__FUNC_SPINOR_IO1>;
+			bias-pull-down;
+		};
+
+		pins1 {
+			pinmux = <PINMUX_GPIO140__FUNC_SPINOR_CS>,
+				 <PINMUX_GPIO130__FUNC_SPINOR_IO2>,
+				 <PINMUX_GPIO131__FUNC_SPINOR_IO3>;
+			bias-pull-up;
+		};
+	};
+
+	uart0_pin: uart0-pins {
+		pins {
+			pinmux = <PINMUX_GPIO98__FUNC_UTXD0>,
+				 <PINMUX_GPIO99__FUNC_URXD0>;
+		};
+	};
+};
+
+&u3phy0 {
+	status = "okay";
+};
+
+&u3phy1 {
+	status = "okay";
+};
+
+&u3phy2 {
+	status = "okay";
+};
+
+&u3phy3 {
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pin>;
+	status = "okay";
+};
+
+&xhci0 {
+	status = "okay";
+};
+
+&xhci1 {
+	status = "okay";
+};
+
+&xhci2 {
+	status = "okay";
+};
+
+&xhci3 {
+	/* This controller is connected with a BT device.
+	 * Disable usb2 lpm to prevent known issues.
+	 */
+	usb2-lpm-disable;
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/mediatek/mt8195.dtsi b/arch/arm64/boot/dts/mediatek/mt8195.dtsi
new file mode 100644
index 000000000000..905d1a90b406
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt8195.dtsi
@@ -0,0 +1,2159 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/*
+ * Copyright (c) 2021 MediaTek Inc.
+ * Author: Seiya Wang <seiya.wang@mediatek.com>
+ */
+
+/dts-v1/;
+#include <dt-bindings/clock/mt8195-clk.h>
+#include <dt-bindings/gce/mt8195-gce.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/memory/mt8195-memory-port.h>
+#include <dt-bindings/phy/phy.h>
+#include <dt-bindings/pinctrl/mt8195-pinfunc.h>
+#include <dt-bindings/power/mt8195-power.h>
+
+/ {
+	compatible = "mediatek,mt8195";
+	interrupt-parent = <&gic>;
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	aliases {
+		gce0 = &gce0;
+		gce1 = &gce1;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a55";
+			reg = <0x000>;
+			enable-method = "psci";
+			performance-domains = <&performance 0>;
+			clock-frequency = <1701000000>;
+			capacity-dmips-mhz = <578>;
+			cpu-idle-states = <&cpu_off_l &cluster_off_l>;
+			next-level-cache = <&l2_0>;
+			#cooling-cells = <2>;
+		};
+
+		cpu1: cpu@100 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a55";
+			reg = <0x100>;
+			enable-method = "psci";
+			performance-domains = <&performance 0>;
+			clock-frequency = <1701000000>;
+			capacity-dmips-mhz = <578>;
+			cpu-idle-states = <&cpu_off_l &cluster_off_l>;
+			next-level-cache = <&l2_0>;
+			#cooling-cells = <2>;
+		};
+
+		cpu2: cpu@200 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a55";
+			reg = <0x200>;
+			enable-method = "psci";
+			performance-domains = <&performance 0>;
+			clock-frequency = <1701000000>;
+			capacity-dmips-mhz = <578>;
+			cpu-idle-states = <&cpu_off_l &cluster_off_l>;
+			next-level-cache = <&l2_0>;
+			#cooling-cells = <2>;
+		};
+
+		cpu3: cpu@300 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a55";
+			reg = <0x300>;
+			enable-method = "psci";
+			performance-domains = <&performance 0>;
+			clock-frequency = <1701000000>;
+			capacity-dmips-mhz = <578>;
+			cpu-idle-states = <&cpu_off_l &cluster_off_l>;
+			next-level-cache = <&l2_0>;
+			#cooling-cells = <2>;
+		};
+
+		cpu4: cpu@400 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a78";
+			reg = <0x400>;
+			enable-method = "psci";
+			performance-domains = <&performance 1>;
+			clock-frequency = <2171000000>;
+			capacity-dmips-mhz = <1024>;
+			cpu-idle-states = <&cpu_off_b &cluster_off_b>;
+			next-level-cache = <&l2_1>;
+			#cooling-cells = <2>;
+		};
+
+		cpu5: cpu@500 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a78";
+			reg = <0x500>;
+			enable-method = "psci";
+			performance-domains = <&performance 1>;
+			clock-frequency = <2171000000>;
+			capacity-dmips-mhz = <1024>;
+			cpu-idle-states = <&cpu_off_b &cluster_off_b>;
+			next-level-cache = <&l2_1>;
+			#cooling-cells = <2>;
+		};
+
+		cpu6: cpu@600 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a78";
+			reg = <0x600>;
+			enable-method = "psci";
+			performance-domains = <&performance 1>;
+			clock-frequency = <2171000000>;
+			capacity-dmips-mhz = <1024>;
+			cpu-idle-states = <&cpu_off_b &cluster_off_b>;
+			next-level-cache = <&l2_1>;
+			#cooling-cells = <2>;
+		};
+
+		cpu7: cpu@700 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a78";
+			reg = <0x700>;
+			enable-method = "psci";
+			performance-domains = <&performance 1>;
+			clock-frequency = <2171000000>;
+			capacity-dmips-mhz = <1024>;
+			cpu-idle-states = <&cpu_off_b &cluster_off_b>;
+			next-level-cache = <&l2_1>;
+			#cooling-cells = <2>;
+		};
+
+		cpu-map {
+			cluster0 {
+				core0 {
+					cpu = <&cpu0>;
+				};
+
+				core1 {
+					cpu = <&cpu1>;
+				};
+
+				core2 {
+					cpu = <&cpu2>;
+				};
+
+				core3 {
+					cpu = <&cpu3>;
+				};
+			};
+
+			cluster1 {
+				core0 {
+					cpu = <&cpu4>;
+				};
+
+				core1 {
+					cpu = <&cpu5>;
+				};
+
+				core2 {
+					cpu = <&cpu6>;
+				};
+
+				core3 {
+					cpu = <&cpu7>;
+				};
+			};
+		};
+
+		idle-states {
+			entry-method = "psci";
+
+			cpu_off_l: cpu-off-l {
+				compatible = "arm,idle-state";
+				arm,psci-suspend-param = <0x00010001>;
+				local-timer-stop;
+				entry-latency-us = <50>;
+				exit-latency-us = <95>;
+				min-residency-us = <580>;
+			};
+
+			cpu_off_b: cpu-off-b {
+				compatible = "arm,idle-state";
+				arm,psci-suspend-param = <0x00010001>;
+				local-timer-stop;
+				entry-latency-us = <45>;
+				exit-latency-us = <140>;
+				min-residency-us = <740>;
+			};
+
+			cluster_off_l: cluster-off-l {
+				compatible = "arm,idle-state";
+				arm,psci-suspend-param = <0x01010002>;
+				local-timer-stop;
+				entry-latency-us = <55>;
+				exit-latency-us = <155>;
+				min-residency-us = <840>;
+			};
+
+			cluster_off_b: cluster-off-b {
+				compatible = "arm,idle-state";
+				arm,psci-suspend-param = <0x01010002>;
+				local-timer-stop;
+				entry-latency-us = <50>;
+				exit-latency-us = <200>;
+				min-residency-us = <1000>;
+			};
+		};
+
+		l2_0: l2-cache0 {
+			compatible = "cache";
+			next-level-cache = <&l3_0>;
+		};
+
+		l2_1: l2-cache1 {
+			compatible = "cache";
+			next-level-cache = <&l3_0>;
+		};
+
+		l3_0: l3-cache {
+			compatible = "cache";
+		};
+	};
+
+	dsu-pmu {
+		compatible = "arm,dsu-pmu";
+		interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH 0>;
+		cpus = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>,
+		       <&cpu4>, <&cpu5>, <&cpu6>, <&cpu7>;
+	};
+
+	dmic_codec: dmic-codec {
+		compatible = "dmic-codec";
+		num-channels = <2>;
+		wakeup-delay-ms = <50>;
+	};
+
+	sound: mt8195-sound {
+		mediatek,platform = <&afe>;
+		status = "disabled";
+	};
+
+	clk26m: oscillator-26m {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <26000000>;
+		clock-output-names = "clk26m";
+	};
+
+	clk32k: oscillator-32k {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		clock-output-names = "clk32k";
+	};
+
+	performance: performance-controller@11bc10 {
+		compatible = "mediatek,cpufreq-hw";
+		reg = <0 0x0011bc10 0 0x120>, <0 0x0011bd30 0 0x120>;
+		#performance-domain-cells = <1>;
+	};
+
+	pmu-a55 {
+		compatible = "arm,cortex-a55-pmu";
+		interrupt-parent = <&gic>;
+		interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH &ppi_cluster0>;
+	};
+
+	pmu-a78 {
+		compatible = "arm,cortex-a78-pmu";
+		interrupt-parent = <&gic>;
+		interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH &ppi_cluster1>;
+	};
+
+	psci {
+		compatible = "arm,psci-1.0";
+		method = "smc";
+	};
+
+	timer: timer {
+		compatible = "arm,armv8-timer";
+		interrupt-parent = <&gic>;
+		interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_HIGH 0>,
+			     <GIC_PPI 14 IRQ_TYPE_LEVEL_HIGH 0>,
+			     <GIC_PPI 11 IRQ_TYPE_LEVEL_HIGH 0>,
+			     <GIC_PPI 10 IRQ_TYPE_LEVEL_HIGH 0>;
+	};
+
+	soc {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		compatible = "simple-bus";
+		ranges;
+
+		gic: interrupt-controller@c000000 {
+			compatible = "arm,gic-v3";
+			#interrupt-cells = <4>;
+			#redistributor-regions = <1>;
+			interrupt-parent = <&gic>;
+			interrupt-controller;
+			reg = <0 0x0c000000 0 0x40000>,
+			      <0 0x0c040000 0 0x200000>;
+			interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH 0>;
+
+			ppi-partitions {
+				ppi_cluster0: interrupt-partition-0 {
+					affinity = <&cpu0 &cpu1 &cpu2 &cpu3>;
+				};
+
+				ppi_cluster1: interrupt-partition-1 {
+					affinity = <&cpu4 &cpu5 &cpu6 &cpu7>;
+				};
+			};
+		};
+
+		topckgen: syscon@10000000 {
+			compatible = "mediatek,mt8195-topckgen", "syscon";
+			reg = <0 0x10000000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
+		infracfg_ao: syscon@10001000 {
+			compatible = "mediatek,mt8195-infracfg_ao", "syscon", "simple-mfd";
+			reg = <0 0x10001000 0 0x1000>;
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+		};
+
+		pericfg: syscon@10003000 {
+			compatible = "mediatek,mt8195-pericfg", "syscon";
+			reg = <0 0x10003000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
+		pio: pinctrl@10005000 {
+			compatible = "mediatek,mt8195-pinctrl";
+			reg = <0 0x10005000 0 0x1000>,
+			      <0 0x11d10000 0 0x1000>,
+			      <0 0x11d30000 0 0x1000>,
+			      <0 0x11d40000 0 0x1000>,
+			      <0 0x11e20000 0 0x1000>,
+			      <0 0x11eb0000 0 0x1000>,
+			      <0 0x11f40000 0 0x1000>,
+			      <0 0x1000b000 0 0x1000>;
+			reg-names = "iocfg0", "iocfg_bm", "iocfg_bl",
+				    "iocfg_br", "iocfg_lm", "iocfg_rb",
+				    "iocfg_tl", "eint";
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&pio 0 0 144>;
+			interrupt-controller;
+			interrupts = <GIC_SPI 235 IRQ_TYPE_LEVEL_HIGH 0>;
+			#interrupt-cells = <2>;
+		};
+
+		scpsys: syscon@10006000 {
+			compatible = "mediatek,mt8195-scpsys", "syscon", "simple-mfd";
+			reg = <0 0x10006000 0 0x1000>;
+
+			/* System Power Manager */
+			spm: power-controller {
+				compatible = "mediatek,mt8195-power-controller";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				#power-domain-cells = <1>;
+
+				/* power domain of the SoC */
+				mfg0: power-domain@MT8195_POWER_DOMAIN_MFG0 {
+					reg = <MT8195_POWER_DOMAIN_MFG0>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+					#power-domain-cells = <1>;
+
+					power-domain@MT8195_POWER_DOMAIN_MFG1 {
+						reg = <MT8195_POWER_DOMAIN_MFG1>;
+						clocks = <&apmixedsys CLK_APMIXED_MFGPLL>;
+						clock-names = "mfg";
+						mediatek,infracfg = <&infracfg_ao>;
+						#address-cells = <1>;
+						#size-cells = <0>;
+						#power-domain-cells = <1>;
+
+						power-domain@MT8195_POWER_DOMAIN_MFG2 {
+							reg = <MT8195_POWER_DOMAIN_MFG2>;
+							#power-domain-cells = <0>;
+						};
+
+						power-domain@MT8195_POWER_DOMAIN_MFG3 {
+							reg = <MT8195_POWER_DOMAIN_MFG3>;
+							#power-domain-cells = <0>;
+						};
+
+						power-domain@MT8195_POWER_DOMAIN_MFG4 {
+							reg = <MT8195_POWER_DOMAIN_MFG4>;
+							#power-domain-cells = <0>;
+						};
+
+						power-domain@MT8195_POWER_DOMAIN_MFG5 {
+							reg = <MT8195_POWER_DOMAIN_MFG5>;
+							#power-domain-cells = <0>;
+						};
+
+						power-domain@MT8195_POWER_DOMAIN_MFG6 {
+							reg = <MT8195_POWER_DOMAIN_MFG6>;
+							#power-domain-cells = <0>;
+						};
+					};
+				};
+
+				power-domain@MT8195_POWER_DOMAIN_VPPSYS0 {
+					reg = <MT8195_POWER_DOMAIN_VPPSYS0>;
+					clocks = <&topckgen CLK_TOP_VPP>,
+						 <&topckgen CLK_TOP_CAM>,
+						 <&topckgen CLK_TOP_CCU>,
+						 <&topckgen CLK_TOP_IMG>,
+						 <&topckgen CLK_TOP_VENC>,
+						 <&topckgen CLK_TOP_VDEC>,
+						 <&topckgen CLK_TOP_WPE_VPP>,
+						 <&topckgen CLK_TOP_CFG_VPP0>,
+						 <&vppsys0 CLK_VPP0_SMI_COMMON>,
+						 <&vppsys0 CLK_VPP0_GALS_VDO0_LARB0>,
+						 <&vppsys0 CLK_VPP0_GALS_VDO0_LARB1>,
+						 <&vppsys0 CLK_VPP0_GALS_VENCSYS>,
+						 <&vppsys0 CLK_VPP0_GALS_VENCSYS_CORE1>,
+						 <&vppsys0 CLK_VPP0_GALS_INFRA>,
+						 <&vppsys0 CLK_VPP0_GALS_CAMSYS>,
+						 <&vppsys0 CLK_VPP0_GALS_VPP1_LARB5>,
+						 <&vppsys0 CLK_VPP0_GALS_VPP1_LARB6>,
+						 <&vppsys0 CLK_VPP0_SMI_REORDER>,
+						 <&vppsys0 CLK_VPP0_SMI_IOMMU>,
+						 <&vppsys0 CLK_VPP0_GALS_IMGSYS_CAMSYS>,
+						 <&vppsys0 CLK_VPP0_GALS_EMI0_EMI1>,
+						 <&vppsys0 CLK_VPP0_SMI_SUB_COMMON_REORDER>,
+						 <&vppsys0 CLK_VPP0_SMI_RSI>,
+						 <&vppsys0 CLK_VPP0_SMI_COMMON_LARB4>,
+						 <&vppsys0 CLK_VPP0_GALS_VDEC_VDEC_CORE1>,
+						 <&vppsys0 CLK_VPP0_GALS_VPP1_WPE>,
+						 <&vppsys0 CLK_VPP0_GALS_VDO0_VDO1_VENCSYS_CORE1>;
+					clock-names = "vppsys", "vppsys1", "vppsys2", "vppsys3",
+						      "vppsys4", "vppsys5", "vppsys6", "vppsys7",
+						      "vppsys0-0", "vppsys0-1", "vppsys0-2", "vppsys0-3",
+						      "vppsys0-4", "vppsys0-5", "vppsys0-6", "vppsys0-7",
+						      "vppsys0-8", "vppsys0-9", "vppsys0-10", "vppsys0-11",
+						      "vppsys0-12", "vppsys0-13", "vppsys0-14",
+						      "vppsys0-15", "vppsys0-16", "vppsys0-17",
+						      "vppsys0-18";
+					mediatek,infracfg = <&infracfg_ao>;
+					#address-cells = <1>;
+					#size-cells = <0>;
+					#power-domain-cells = <1>;
+
+					power-domain@MT8195_POWER_DOMAIN_VDEC1 {
+						reg = <MT8195_POWER_DOMAIN_VDEC1>;
+						clocks = <&vdecsys CLK_VDEC_LARB1>;
+						clock-names = "vdec1-0";
+						mediatek,infracfg = <&infracfg_ao>;
+						#power-domain-cells = <0>;
+					};
+
+					power-domain@MT8195_POWER_DOMAIN_VENC_CORE1 {
+						reg = <MT8195_POWER_DOMAIN_VENC_CORE1>;
+						mediatek,infracfg = <&infracfg_ao>;
+						#power-domain-cells = <0>;
+					};
+
+					power-domain@MT8195_POWER_DOMAIN_VDOSYS0 {
+						reg = <MT8195_POWER_DOMAIN_VDOSYS0>;
+						clocks = <&topckgen CLK_TOP_CFG_VDO0>,
+							 <&vdosys0 CLK_VDO0_SMI_GALS>,
+							 <&vdosys0 CLK_VDO0_SMI_COMMON>,
+							 <&vdosys0 CLK_VDO0_SMI_EMI>,
+							 <&vdosys0 CLK_VDO0_SMI_IOMMU>,
+							 <&vdosys0 CLK_VDO0_SMI_LARB>,
+							 <&vdosys0 CLK_VDO0_SMI_RSI>;
+						clock-names = "vdosys0", "vdosys0-0", "vdosys0-1",
+							      "vdosys0-2", "vdosys0-3",
+							      "vdosys0-4", "vdosys0-5";
+						mediatek,infracfg = <&infracfg_ao>;
+						#address-cells = <1>;
+						#size-cells = <0>;
+						#power-domain-cells = <1>;
+
+						power-domain@MT8195_POWER_DOMAIN_VPPSYS1 {
+							reg = <MT8195_POWER_DOMAIN_VPPSYS1>;
+							clocks = <&topckgen CLK_TOP_CFG_VPP1>,
+								 <&vppsys1 CLK_VPP1_VPPSYS1_GALS>,
+								 <&vppsys1 CLK_VPP1_VPPSYS1_LARB>;
+							clock-names = "vppsys1", "vppsys1-0",
+								      "vppsys1-1";
+							mediatek,infracfg = <&infracfg_ao>;
+							#power-domain-cells = <0>;
+						};
+
+						power-domain@MT8195_POWER_DOMAIN_WPESYS {
+							reg = <MT8195_POWER_DOMAIN_WPESYS>;
+							clocks = <&wpesys CLK_WPE_SMI_LARB7>,
+								 <&wpesys CLK_WPE_SMI_LARB8>,
+								 <&wpesys CLK_WPE_SMI_LARB7_P>,
+								 <&wpesys CLK_WPE_SMI_LARB8_P>;
+							clock-names = "wepsys-0", "wepsys-1", "wepsys-2",
+								      "wepsys-3";
+							mediatek,infracfg = <&infracfg_ao>;
+							#power-domain-cells = <0>;
+						};
+
+						power-domain@MT8195_POWER_DOMAIN_VDEC0 {
+							reg = <MT8195_POWER_DOMAIN_VDEC0>;
+							clocks = <&vdecsys_soc CLK_VDEC_SOC_LARB1>;
+							clock-names = "vdec0-0";
+							mediatek,infracfg = <&infracfg_ao>;
+							#power-domain-cells = <0>;
+						};
+
+						power-domain@MT8195_POWER_DOMAIN_VDEC2 {
+							reg = <MT8195_POWER_DOMAIN_VDEC2>;
+							clocks = <&vdecsys_core1 CLK_VDEC_CORE1_LARB1>;
+							clock-names = "vdec2-0";
+							mediatek,infracfg = <&infracfg_ao>;
+							#power-domain-cells = <0>;
+						};
+
+						power-domain@MT8195_POWER_DOMAIN_VENC {
+							reg = <MT8195_POWER_DOMAIN_VENC>;
+							mediatek,infracfg = <&infracfg_ao>;
+							#power-domain-cells = <0>;
+						};
+
+						power-domain@MT8195_POWER_DOMAIN_VDOSYS1 {
+							reg = <MT8195_POWER_DOMAIN_VDOSYS1>;
+							clocks = <&topckgen CLK_TOP_CFG_VDO1>,
+								 <&vdosys1 CLK_VDO1_SMI_LARB2>,
+								 <&vdosys1 CLK_VDO1_SMI_LARB3>,
+								 <&vdosys1 CLK_VDO1_GALS>;
+							clock-names = "vdosys1", "vdosys1-0",
+								      "vdosys1-1", "vdosys1-2";
+							mediatek,infracfg = <&infracfg_ao>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+							#power-domain-cells = <1>;
+
+							power-domain@MT8195_POWER_DOMAIN_DP_TX {
+								reg = <MT8195_POWER_DOMAIN_DP_TX>;
+								mediatek,infracfg = <&infracfg_ao>;
+								#power-domain-cells = <0>;
+							};
+
+							power-domain@MT8195_POWER_DOMAIN_EPD_TX {
+								reg = <MT8195_POWER_DOMAIN_EPD_TX>;
+								mediatek,infracfg = <&infracfg_ao>;
+								#power-domain-cells = <0>;
+							};
+
+							power-domain@MT8195_POWER_DOMAIN_HDMI_TX {
+								reg = <MT8195_POWER_DOMAIN_HDMI_TX>;
+								clocks = <&topckgen CLK_TOP_HDMI_APB>;
+								clock-names = "hdmi_tx";
+								#power-domain-cells = <0>;
+							};
+						};
+
+						power-domain@MT8195_POWER_DOMAIN_IMG {
+							reg = <MT8195_POWER_DOMAIN_IMG>;
+							clocks = <&imgsys CLK_IMG_LARB9>,
+								 <&imgsys CLK_IMG_GALS>;
+							clock-names = "img-0", "img-1";
+							mediatek,infracfg = <&infracfg_ao>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+							#power-domain-cells = <1>;
+
+							power-domain@MT8195_POWER_DOMAIN_DIP {
+								reg = <MT8195_POWER_DOMAIN_DIP>;
+								#power-domain-cells = <0>;
+							};
+
+							power-domain@MT8195_POWER_DOMAIN_IPE {
+								reg = <MT8195_POWER_DOMAIN_IPE>;
+								clocks = <&topckgen CLK_TOP_IPE>,
+									 <&imgsys CLK_IMG_IPE>,
+									 <&ipesys CLK_IPE_SMI_LARB12>;
+								clock-names = "ipe", "ipe-0", "ipe-1";
+								mediatek,infracfg = <&infracfg_ao>;
+								#power-domain-cells = <0>;
+							};
+						};
+
+						power-domain@MT8195_POWER_DOMAIN_CAM {
+							reg = <MT8195_POWER_DOMAIN_CAM>;
+							clocks = <&camsys CLK_CAM_LARB13>,
+								 <&camsys CLK_CAM_LARB14>,
+								 <&camsys CLK_CAM_CAM2MM0_GALS>,
+								 <&camsys CLK_CAM_CAM2MM1_GALS>,
+								 <&camsys CLK_CAM_CAM2SYS_GALS>;
+							clock-names = "cam-0", "cam-1", "cam-2", "cam-3",
+								      "cam-4";
+							mediatek,infracfg = <&infracfg_ao>;
+							#address-cells = <1>;
+							#size-cells = <0>;
+							#power-domain-cells = <1>;
+
+							power-domain@MT8195_POWER_DOMAIN_CAM_RAWA {
+								reg = <MT8195_POWER_DOMAIN_CAM_RAWA>;
+								#power-domain-cells = <0>;
+							};
+
+							power-domain@MT8195_POWER_DOMAIN_CAM_RAWB {
+								reg = <MT8195_POWER_DOMAIN_CAM_RAWB>;
+								#power-domain-cells = <0>;
+							};
+
+							power-domain@MT8195_POWER_DOMAIN_CAM_MRAW {
+								reg = <MT8195_POWER_DOMAIN_CAM_MRAW>;
+								#power-domain-cells = <0>;
+							};
+						};
+					};
+				};
+
+				power-domain@MT8195_POWER_DOMAIN_PCIE_MAC_P0 {
+					reg = <MT8195_POWER_DOMAIN_PCIE_MAC_P0>;
+					mediatek,infracfg = <&infracfg_ao>;
+					#power-domain-cells = <0>;
+				};
+
+				power-domain@MT8195_POWER_DOMAIN_PCIE_MAC_P1 {
+					reg = <MT8195_POWER_DOMAIN_PCIE_MAC_P1>;
+					mediatek,infracfg = <&infracfg_ao>;
+					#power-domain-cells = <0>;
+				};
+
+				power-domain@MT8195_POWER_DOMAIN_PCIE_PHY {
+					reg = <MT8195_POWER_DOMAIN_PCIE_PHY>;
+					#power-domain-cells = <0>;
+				};
+
+				power-domain@MT8195_POWER_DOMAIN_SSUSB_PCIE_PHY {
+					reg = <MT8195_POWER_DOMAIN_SSUSB_PCIE_PHY>;
+					#power-domain-cells = <0>;
+				};
+
+				power-domain@MT8195_POWER_DOMAIN_CSI_RX_TOP {
+					reg = <MT8195_POWER_DOMAIN_CSI_RX_TOP>;
+					clocks = <&topckgen CLK_TOP_SENINF>,
+						 <&topckgen CLK_TOP_SENINF2>;
+					clock-names = "csi_rx_top", "csi_rx_top1";
+					#power-domain-cells = <0>;
+				};
+
+				power-domain@MT8195_POWER_DOMAIN_ETHER {
+					reg = <MT8195_POWER_DOMAIN_ETHER>;
+					clocks = <&pericfg_ao CLK_PERI_AO_ETHERNET_MAC>;
+					clock-names = "ether";
+					#power-domain-cells = <0>;
+				};
+
+				power-domain@MT8195_POWER_DOMAIN_ADSP {
+					reg = <MT8195_POWER_DOMAIN_ADSP>;
+					clocks = <&topckgen CLK_TOP_ADSP>,
+						 <&topckgen CLK_TOP_AUDIO_LOCAL_BUS>;
+					clock-names = "adsp", "adsp1";
+					#address-cells = <1>;
+					#size-cells = <0>;
+					mediatek,infracfg = <&infracfg_ao>;
+					#power-domain-cells = <1>;
+
+					power-domain@MT8195_POWER_DOMAIN_AUDIO {
+						reg = <MT8195_POWER_DOMAIN_AUDIO>;
+						clocks = <&topckgen CLK_TOP_A1SYS_HP>,
+							 <&topckgen CLK_TOP_AUD_INTBUS>,
+							 <&topckgen CLK_TOP_AUDIO_LOCAL_BUS>,
+							 <&infracfg_ao CLK_INFRA_AO_AUDIO_26M_B>;
+						clock-names = "audio", "audio1", "audio2",
+							      "audio3";
+						mediatek,infracfg = <&infracfg_ao>;
+						#power-domain-cells = <0>;
+					};
+				};
+			};
+		};
+
+		watchdog: watchdog@10007000 {
+			compatible = "mediatek,mt8195-wdt",
+				     "mediatek,mt6589-wdt";
+			mediatek,disable-extrst;
+			reg = <0 0x10007000 0 0x100>;
+			#reset-cells = <1>;
+		};
+
+		apmixedsys: syscon@1000c000 {
+			compatible = "mediatek,mt8195-apmixedsys", "syscon";
+			reg = <0 0x1000c000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
+		systimer: timer@10017000 {
+			compatible = "mediatek,mt8195-timer",
+				     "mediatek,mt6765-timer";
+			reg = <0 0x10017000 0 0x1000>;
+			interrupts = <GIC_SPI 265 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&topckgen CLK_TOP_CLK26M_D2>;
+		};
+
+		pwrap: pwrap@10024000 {
+			compatible = "mediatek,mt8195-pwrap", "syscon";
+			reg = <0 0x10024000 0 0x1000>;
+			reg-names = "pwrap";
+			interrupts = <GIC_SPI 243 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&infracfg_ao CLK_INFRA_AO_PMIC_AP>,
+				 <&infracfg_ao CLK_INFRA_AO_PMIC_TMR>;
+			clock-names = "spi", "wrap";
+			assigned-clocks = <&topckgen CLK_TOP_PWRAP_ULPOSC>;
+			assigned-clock-parents = <&topckgen CLK_TOP_ULPOSC1_D10>;
+		};
+
+		spmi: spmi@10027000 {
+			compatible = "mediatek,mt8195-spmi";
+			reg = <0 0x10027000 0 0x000e00>,
+			      <0 0x10029000 0 0x000100>;
+			reg-names = "pmif", "spmimst";
+			clocks = <&infracfg_ao CLK_INFRA_AO_PMIC_AP>,
+				 <&infracfg_ao CLK_INFRA_AO_PMIC_TMR>,
+				 <&topckgen CLK_TOP_SPMI_M_MST>;
+			clock-names = "pmif_sys_ck",
+				      "pmif_tmr_ck",
+				      "spmimst_clk_mux";
+			assigned-clocks = <&topckgen CLK_TOP_PWRAP_ULPOSC>;
+			assigned-clock-parents = <&topckgen CLK_TOP_ULPOSC1_D10>;
+		};
+
+		iommu_infra: infra-iommu@10315000 {
+			compatible = "mediatek,mt8195-iommu-infra";
+			reg = <0 0x10315000 0 0x5000>;
+			interrupts = <GIC_SPI 795 IRQ_TYPE_LEVEL_HIGH 0>,
+				     <GIC_SPI 796 IRQ_TYPE_LEVEL_HIGH 0>,
+				     <GIC_SPI 797 IRQ_TYPE_LEVEL_HIGH 0>,
+				     <GIC_SPI 798 IRQ_TYPE_LEVEL_HIGH 0>,
+				     <GIC_SPI 799 IRQ_TYPE_LEVEL_HIGH 0>;
+			#iommu-cells = <1>;
+		};
+
+		gce0: mailbox@10320000 {
+			compatible = "mediatek,mt8195-gce";
+			reg = <0 0x10320000 0 0x4000>;
+			interrupts = <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH 0>;
+			#mbox-cells = <2>;
+			clocks = <&infracfg_ao CLK_INFRA_AO_GCE>;
+		};
+
+		gce1: mailbox@10330000 {
+			compatible = "mediatek,mt8195-gce";
+			reg = <0 0x10330000 0 0x4000>;
+			interrupts = <GIC_SPI 228 IRQ_TYPE_LEVEL_HIGH 0>;
+			#mbox-cells = <2>;
+			clocks = <&infracfg_ao CLK_INFRA_AO_GCE2>;
+		};
+
+		scp: scp@10500000 {
+			compatible = "mediatek,mt8195-scp";
+			reg = <0 0x10500000 0 0x100000>,
+			      <0 0x10720000 0 0xe0000>,
+			      <0 0x10700000 0 0x8000>;
+			reg-names = "sram", "cfg", "l1tcm";
+			interrupts = <GIC_SPI 462 IRQ_TYPE_LEVEL_HIGH 0>;
+			status = "disabled";
+		};
+
+		scp_adsp: clock-controller@10720000 {
+			compatible = "mediatek,mt8195-scp_adsp";
+			reg = <0 0x10720000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
+		adsp: dsp@10803000 {
+			compatible = "mediatek,mt8195-dsp";
+			reg = <0 0x10803000 0 0x1000>,
+			      <0 0x10840000 0 0x40000>;
+			reg-names = "cfg", "sram";
+			clocks = <&topckgen CLK_TOP_ADSP>,
+				 <&clk26m>,
+				 <&topckgen CLK_TOP_AUDIO_LOCAL_BUS>,
+				 <&topckgen CLK_TOP_MAINPLL_D7_D2>,
+				 <&scp_adsp CLK_SCP_ADSP_AUDIODSP>,
+				 <&topckgen CLK_TOP_AUDIO_H>;
+			clock-names = "adsp_sel",
+				 "clk26m_ck",
+				 "audio_local_bus",
+				 "mainpll_d7_d2",
+				 "scp_adsp_audiodsp",
+				 "audio_h";
+			power-domains = <&spm MT8195_POWER_DOMAIN_ADSP>;
+			mbox-names = "rx", "tx";
+			mboxes = <&adsp_mailbox0>, <&adsp_mailbox1>;
+			status = "disabled";
+		};
+
+		adsp_mailbox0: mailbox@10816000 {
+			compatible = "mediatek,mt8195-adsp-mbox";
+			#mbox-cells = <0>;
+			reg = <0 0x10816000 0 0x1000>;
+			interrupts = <GIC_SPI 702 IRQ_TYPE_LEVEL_HIGH 0>;
+		};
+
+		adsp_mailbox1: mailbox@10817000 {
+			compatible = "mediatek,mt8195-adsp-mbox";
+			#mbox-cells = <0>;
+			reg = <0 0x10817000 0 0x1000>;
+			interrupts = <GIC_SPI 703 IRQ_TYPE_LEVEL_HIGH 0>;
+		};
+
+		afe: mt8195-afe-pcm@10890000 {
+			compatible = "mediatek,mt8195-audio";
+			reg = <0 0x10890000 0 0x10000>;
+			mediatek,topckgen = <&topckgen>;
+			power-domains = <&spm MT8195_POWER_DOMAIN_AUDIO>;
+			interrupts = <GIC_SPI 822 IRQ_TYPE_LEVEL_HIGH 0>;
+			resets = <&watchdog 14>;
+			reset-names = "audiosys";
+			clocks = <&clk26m>,
+				<&apmixedsys CLK_APMIXED_APLL1>,
+				<&apmixedsys CLK_APMIXED_APLL2>,
+				<&topckgen CLK_TOP_APLL12_DIV0>,
+				<&topckgen CLK_TOP_APLL12_DIV1>,
+				<&topckgen CLK_TOP_APLL12_DIV2>,
+				<&topckgen CLK_TOP_APLL12_DIV3>,
+				<&topckgen CLK_TOP_APLL12_DIV9>,
+				<&topckgen CLK_TOP_A1SYS_HP>,
+				<&topckgen CLK_TOP_AUD_INTBUS>,
+				<&topckgen CLK_TOP_AUDIO_H>,
+				<&topckgen CLK_TOP_AUDIO_LOCAL_BUS>,
+				<&topckgen CLK_TOP_DPTX_MCK>,
+				<&topckgen CLK_TOP_I2SO1_MCK>,
+				<&topckgen CLK_TOP_I2SO2_MCK>,
+				<&topckgen CLK_TOP_I2SI1_MCK>,
+				<&topckgen CLK_TOP_I2SI2_MCK>,
+				<&infracfg_ao CLK_INFRA_AO_AUDIO_26M_B>,
+				<&scp_adsp CLK_SCP_ADSP_AUDIODSP>;
+			clock-names = "clk26m",
+				"apll1_ck",
+				"apll2_ck",
+				"apll12_div0",
+				"apll12_div1",
+				"apll12_div2",
+				"apll12_div3",
+				"apll12_div9",
+				"a1sys_hp_sel",
+				"aud_intbus_sel",
+				"audio_h_sel",
+				"audio_local_bus_sel",
+				"dptx_m_sel",
+				"i2so1_m_sel",
+				"i2so2_m_sel",
+				"i2si1_m_sel",
+				"i2si2_m_sel",
+				"infra_ao_audio_26m_b",
+				"scp_adsp_audiodsp";
+			status = "disabled";
+		};
+
+		uart0: serial@11001100 {
+			compatible = "mediatek,mt8195-uart",
+				     "mediatek,mt6577-uart";
+			reg = <0 0x11001100 0 0x100>;
+			interrupts = <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&clk26m>, <&infracfg_ao CLK_INFRA_AO_UART0>;
+			clock-names = "baud", "bus";
+			status = "disabled";
+		};
+
+		uart1: serial@11001200 {
+			compatible = "mediatek,mt8195-uart",
+				     "mediatek,mt6577-uart";
+			reg = <0 0x11001200 0 0x100>;
+			interrupts = <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&clk26m>, <&infracfg_ao CLK_INFRA_AO_UART1>;
+			clock-names = "baud", "bus";
+			status = "disabled";
+		};
+
+		uart2: serial@11001300 {
+			compatible = "mediatek,mt8195-uart",
+				     "mediatek,mt6577-uart";
+			reg = <0 0x11001300 0 0x100>;
+			interrupts = <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&clk26m>, <&infracfg_ao CLK_INFRA_AO_UART2>;
+			clock-names = "baud", "bus";
+			status = "disabled";
+		};
+
+		uart3: serial@11001400 {
+			compatible = "mediatek,mt8195-uart",
+				     "mediatek,mt6577-uart";
+			reg = <0 0x11001400 0 0x100>;
+			interrupts = <GIC_SPI 723 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&clk26m>, <&infracfg_ao CLK_INFRA_AO_UART3>;
+			clock-names = "baud", "bus";
+			status = "disabled";
+		};
+
+		uart4: serial@11001500 {
+			compatible = "mediatek,mt8195-uart",
+				     "mediatek,mt6577-uart";
+			reg = <0 0x11001500 0 0x100>;
+			interrupts = <GIC_SPI 724 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&clk26m>, <&infracfg_ao CLK_INFRA_AO_UART4>;
+			clock-names = "baud", "bus";
+			status = "disabled";
+		};
+
+		uart5: serial@11001600 {
+			compatible = "mediatek,mt8195-uart",
+				     "mediatek,mt6577-uart";
+			reg = <0 0x11001600 0 0x100>;
+			interrupts = <GIC_SPI 725 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&clk26m>, <&infracfg_ao CLK_INFRA_AO_UART5>;
+			clock-names = "baud", "bus";
+			status = "disabled";
+		};
+
+		auxadc: auxadc@11002000 {
+			compatible = "mediatek,mt8195-auxadc",
+				     "mediatek,mt8173-auxadc";
+			reg = <0 0x11002000 0 0x1000>;
+			clocks = <&infracfg_ao CLK_INFRA_AO_AUXADC>;
+			clock-names = "main";
+			#io-channel-cells = <1>;
+			status = "disabled";
+		};
+
+		pericfg_ao: syscon@11003000 {
+			compatible = "mediatek,mt8195-pericfg_ao", "syscon";
+			reg = <0 0x11003000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
+		spi0: spi@1100a000 {
+			compatible = "mediatek,mt8195-spi",
+				     "mediatek,mt6765-spi";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0 0x1100a000 0 0x1000>;
+			interrupts = <GIC_SPI 191 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&topckgen CLK_TOP_UNIVPLL_D6_D2>,
+				 <&topckgen CLK_TOP_SPI>,
+				 <&infracfg_ao CLK_INFRA_AO_SPI0>;
+			clock-names = "parent-clk", "sel-clk", "spi-clk";
+			status = "disabled";
+		};
+
+		spi1: spi@11010000 {
+			compatible = "mediatek,mt8195-spi",
+				     "mediatek,mt6765-spi";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0 0x11010000 0 0x1000>;
+			interrupts = <GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&topckgen CLK_TOP_UNIVPLL_D6_D2>,
+				 <&topckgen CLK_TOP_SPI>,
+				 <&infracfg_ao CLK_INFRA_AO_SPI1>;
+			clock-names = "parent-clk", "sel-clk", "spi-clk";
+			status = "disabled";
+		};
+
+		spi2: spi@11012000 {
+			compatible = "mediatek,mt8195-spi",
+				     "mediatek,mt6765-spi";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0 0x11012000 0 0x1000>;
+			interrupts = <GIC_SPI 193 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&topckgen CLK_TOP_UNIVPLL_D6_D2>,
+				 <&topckgen CLK_TOP_SPI>,
+				 <&infracfg_ao CLK_INFRA_AO_SPI2>;
+			clock-names = "parent-clk", "sel-clk", "spi-clk";
+			status = "disabled";
+		};
+
+		spi3: spi@11013000 {
+			compatible = "mediatek,mt8195-spi",
+				     "mediatek,mt6765-spi";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0 0x11013000 0 0x1000>;
+			interrupts = <GIC_SPI 194 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&topckgen CLK_TOP_UNIVPLL_D6_D2>,
+				 <&topckgen CLK_TOP_SPI>,
+				 <&infracfg_ao CLK_INFRA_AO_SPI3>;
+			clock-names = "parent-clk", "sel-clk", "spi-clk";
+			status = "disabled";
+		};
+
+		spi4: spi@11018000 {
+			compatible = "mediatek,mt8195-spi",
+				     "mediatek,mt6765-spi";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0 0x11018000 0 0x1000>;
+			interrupts = <GIC_SPI 195 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&topckgen CLK_TOP_UNIVPLL_D6_D2>,
+				 <&topckgen CLK_TOP_SPI>,
+				 <&infracfg_ao CLK_INFRA_AO_SPI4>;
+			clock-names = "parent-clk", "sel-clk", "spi-clk";
+			status = "disabled";
+		};
+
+		spi5: spi@11019000 {
+			compatible = "mediatek,mt8195-spi",
+				     "mediatek,mt6765-spi";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0 0x11019000 0 0x1000>;
+			interrupts = <GIC_SPI 196 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&topckgen CLK_TOP_UNIVPLL_D6_D2>,
+				 <&topckgen CLK_TOP_SPI>,
+				 <&infracfg_ao CLK_INFRA_AO_SPI5>;
+			clock-names = "parent-clk", "sel-clk", "spi-clk";
+			status = "disabled";
+		};
+
+		spis0: spi@1101d000 {
+			compatible = "mediatek,mt8195-spi-slave";
+			reg = <0 0x1101d000 0 0x1000>;
+			interrupts = <GIC_SPI 197 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&infracfg_ao CLK_INFRA_AO_SPIS0>;
+			clock-names = "spi";
+			assigned-clocks = <&topckgen CLK_TOP_SPIS>;
+			assigned-clock-parents = <&topckgen CLK_TOP_UNIVPLL_D6>;
+			status = "disabled";
+		};
+
+		spis1: spi@1101e000 {
+			compatible = "mediatek,mt8195-spi-slave";
+			reg = <0 0x1101e000 0 0x1000>;
+			interrupts = <GIC_SPI 198 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&infracfg_ao CLK_INFRA_AO_SPIS1>;
+			clock-names = "spi";
+			assigned-clocks = <&topckgen CLK_TOP_SPIS>;
+			assigned-clock-parents = <&topckgen CLK_TOP_UNIVPLL_D6>;
+			status = "disabled";
+		};
+
+		xhci0: usb@11200000 {
+			compatible = "mediatek,mt8195-xhci",
+				     "mediatek,mtk-xhci";
+			reg = <0 0x11200000 0 0x1000>,
+			      <0 0x11203e00 0 0x0100>;
+			reg-names = "mac", "ippc";
+			interrupts = <GIC_SPI 129 IRQ_TYPE_LEVEL_HIGH 0>;
+			phys = <&u2port0 PHY_TYPE_USB2>,
+			       <&u3port0 PHY_TYPE_USB3>;
+			assigned-clocks = <&topckgen CLK_TOP_USB_TOP>,
+					  <&topckgen CLK_TOP_SSUSB_XHCI>;
+			assigned-clock-parents = <&topckgen CLK_TOP_UNIVPLL_D5_D4>,
+						 <&topckgen CLK_TOP_UNIVPLL_D5_D4>;
+			clocks = <&infracfg_ao CLK_INFRA_AO_SSUSB>,
+				 <&topckgen CLK_TOP_SSUSB_REF>,
+				 <&apmixedsys CLK_APMIXED_USB1PLL>,
+				 <&clk26m>,
+				 <&infracfg_ao CLK_INFRA_AO_SSUSB_XHCI>;
+			clock-names = "sys_ck", "ref_ck", "mcu_ck", "dma_ck",
+				      "xhci_ck";
+			mediatek,syscon-wakeup = <&pericfg 0x400 103>;
+			wakeup-source;
+			status = "disabled";
+		};
+
+		mmc0: mmc@11230000 {
+			compatible = "mediatek,mt8195-mmc",
+				     "mediatek,mt8183-mmc";
+			reg = <0 0x11230000 0 0x10000>,
+			      <0 0x11f50000 0 0x1000>;
+			interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&topckgen CLK_TOP_MSDC50_0>,
+				 <&infracfg_ao CLK_INFRA_AO_MSDC0>,
+				 <&infracfg_ao CLK_INFRA_AO_MSDC0_SRC>;
+			clock-names = "source", "hclk", "source_cg";
+			status = "disabled";
+		};
+
+		mmc1: mmc@11240000 {
+			compatible = "mediatek,mt8195-mmc",
+				     "mediatek,mt8183-mmc";
+			reg = <0 0x11240000 0 0x1000>,
+			      <0 0x11c70000 0 0x1000>;
+			interrupts = <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&topckgen CLK_TOP_MSDC30_1>,
+				 <&infracfg_ao CLK_INFRA_AO_MSDC1>,
+				 <&infracfg_ao CLK_INFRA_AO_MSDC1_SRC>;
+			clock-names = "source", "hclk", "source_cg";
+			assigned-clocks = <&topckgen CLK_TOP_MSDC30_1>;
+			assigned-clock-parents = <&topckgen CLK_TOP_MSDCPLL_D2>;
+			status = "disabled";
+		};
+
+		mmc2: mmc@11250000 {
+			compatible = "mediatek,mt8195-mmc",
+				     "mediatek,mt8183-mmc";
+			reg = <0 0x11250000 0 0x1000>,
+			      <0 0x11e60000 0 0x1000>;
+			interrupts = <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&topckgen CLK_TOP_MSDC30_2>,
+				 <&infracfg_ao CLK_INFRA_AO_CG1_MSDC2>,
+				 <&infracfg_ao CLK_INFRA_AO_CG3_MSDC2>;
+			clock-names = "source", "hclk", "source_cg";
+			assigned-clocks = <&topckgen CLK_TOP_MSDC30_2>;
+			assigned-clock-parents = <&topckgen CLK_TOP_MSDCPLL_D2>;
+			status = "disabled";
+		};
+
+		xhci1: usb@11290000 {
+			compatible = "mediatek,mt8195-xhci",
+				     "mediatek,mtk-xhci";
+			reg = <0 0x11290000 0 0x1000>,
+			      <0 0x11293e00 0 0x0100>;
+			reg-names = "mac", "ippc";
+			interrupts = <GIC_SPI 530 IRQ_TYPE_LEVEL_HIGH 0>;
+			phys = <&u2port1 PHY_TYPE_USB2>;
+			assigned-clocks = <&topckgen CLK_TOP_USB_TOP_1P>,
+					  <&topckgen CLK_TOP_SSUSB_XHCI_1P>;
+			assigned-clock-parents = <&topckgen CLK_TOP_UNIVPLL_D5_D4>,
+						 <&topckgen CLK_TOP_UNIVPLL_D5_D4>;
+			clocks = <&pericfg_ao CLK_PERI_AO_SSUSB_1P_BUS>,
+				 <&topckgen CLK_TOP_SSUSB_P1_REF>,
+				 <&apmixedsys CLK_APMIXED_USB1PLL>,
+				 <&clk26m>,
+				 <&pericfg_ao CLK_PERI_AO_SSUSB_1P_XHCI>;
+			clock-names = "sys_ck", "ref_ck", "mcu_ck", "dma_ck",
+				      "xhci_ck";
+			mediatek,syscon-wakeup = <&pericfg 0x400 104>;
+			wakeup-source;
+			status = "disabled";
+		};
+
+		xhci2: usb@112a0000 {
+			compatible = "mediatek,mt8195-xhci",
+				     "mediatek,mtk-xhci";
+			reg = <0 0x112a0000 0 0x1000>,
+			      <0 0x112a3e00 0 0x0100>;
+			reg-names = "mac", "ippc";
+			interrupts = <GIC_SPI 533 IRQ_TYPE_LEVEL_HIGH 0>;
+			phys = <&u2port2 PHY_TYPE_USB2>;
+			assigned-clocks = <&topckgen CLK_TOP_USB_TOP_2P>,
+					  <&topckgen CLK_TOP_SSUSB_XHCI_2P>;
+			assigned-clock-parents = <&topckgen CLK_TOP_UNIVPLL_D5_D4>,
+						 <&topckgen CLK_TOP_UNIVPLL_D5_D4>;
+			clocks = <&pericfg_ao CLK_PERI_AO_SSUSB_2P_BUS>,
+				 <&topckgen CLK_TOP_SSUSB_P2_REF>,
+				 <&clk26m>,
+				 <&clk26m>,
+				 <&pericfg_ao CLK_PERI_AO_SSUSB_2P_XHCI>;
+			clock-names = "sys_ck", "ref_ck", "mcu_ck", "dma_ck",
+				      "xhci_ck";
+			mediatek,syscon-wakeup = <&pericfg 0x400 105>;
+			wakeup-source;
+			status = "disabled";
+		};
+
+		xhci3: usb@112b0000 {
+			compatible = "mediatek,mt8195-xhci",
+				     "mediatek,mtk-xhci";
+			reg = <0 0x112b0000 0 0x1000>,
+			      <0 0x112b3e00 0 0x0100>;
+			reg-names = "mac", "ippc";
+			interrupts = <GIC_SPI 536 IRQ_TYPE_LEVEL_HIGH 0>;
+			phys = <&u2port3 PHY_TYPE_USB2>;
+			assigned-clocks = <&topckgen CLK_TOP_USB_TOP_3P>,
+					  <&topckgen CLK_TOP_SSUSB_XHCI_3P>;
+			assigned-clock-parents = <&topckgen CLK_TOP_UNIVPLL_D5_D4>,
+						 <&topckgen CLK_TOP_UNIVPLL_D5_D4>;
+			clocks = <&pericfg_ao CLK_PERI_AO_SSUSB_3P_BUS>,
+				 <&topckgen CLK_TOP_SSUSB_P3_REF>,
+				 <&clk26m>,
+				 <&clk26m>,
+				 <&pericfg_ao CLK_PERI_AO_SSUSB_3P_XHCI>;
+			clock-names = "sys_ck", "ref_ck", "mcu_ck", "dma_ck",
+				      "xhci_ck";
+			mediatek,syscon-wakeup = <&pericfg 0x400 106>;
+			wakeup-source;
+			status = "disabled";
+		};
+
+		nor_flash: spi@1132c000 {
+			compatible = "mediatek,mt8195-nor",
+				     "mediatek,mt8173-nor";
+			reg = <0 0x1132c000 0 0x1000>;
+			interrupts = <GIC_SPI 825 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&topckgen CLK_TOP_SPINOR>,
+				 <&pericfg_ao CLK_PERI_AO_FLASHIF_FLASH>,
+				 <&pericfg_ao CLK_PERI_AO_FLASHIF_BUS>;
+			clock-names = "spi", "sf", "axi";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		efuse: efuse@11c10000 {
+			compatible = "mediatek,mt8195-efuse", "mediatek,efuse";
+			reg = <0 0x11c10000 0 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			u3_tx_imp_p0: usb3-tx-imp@184,1 {
+				reg = <0x184 0x1>;
+				bits = <0 5>;
+			};
+			u3_rx_imp_p0: usb3-rx-imp@184,2 {
+				reg = <0x184 0x2>;
+				bits = <5 5>;
+			};
+			u3_intr_p0: usb3-intr@185 {
+				reg = <0x185 0x1>;
+				bits = <2 6>;
+			};
+			comb_tx_imp_p1: usb3-tx-imp@186,1 {
+				reg = <0x186 0x1>;
+				bits = <0 5>;
+			};
+			comb_rx_imp_p1: usb3-rx-imp@186,2 {
+				reg = <0x186 0x2>;
+				bits = <5 5>;
+			};
+			comb_intr_p1: usb3-intr@187 {
+				reg = <0x187 0x1>;
+				bits = <2 6>;
+			};
+			u2_intr_p0: usb2-intr-p0@188,1 {
+				reg = <0x188 0x1>;
+				bits = <0 5>;
+			};
+			u2_intr_p1: usb2-intr-p1@188,2 {
+				reg = <0x188 0x2>;
+				bits = <5 5>;
+			};
+			u2_intr_p2: usb2-intr-p2@189,1 {
+				reg = <0x189 0x1>;
+				bits = <2 5>;
+			};
+			u2_intr_p3: usb2-intr-p3@189,2 {
+				reg = <0x189 0x2>;
+				bits = <7 5>;
+			};
+		};
+
+		u3phy2: t-phy@11c40000 {
+			compatible = "mediatek,mt8195-tphy", "mediatek,generic-tphy-v3";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0 0x11c40000 0x700>;
+			status = "disabled";
+
+			u2port2: usb-phy@0 {
+				reg = <0x0 0x700>;
+				clocks = <&topckgen CLK_TOP_SSUSB_PHY_P2_REF>;
+				clock-names = "ref";
+				#phy-cells = <1>;
+			};
+		};
+
+		u3phy3: t-phy@11c50000 {
+			compatible = "mediatek,mt8195-tphy", "mediatek,generic-tphy-v3";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0 0x11c50000 0x700>;
+			status = "disabled";
+
+			u2port3: usb-phy@0 {
+				reg = <0x0 0x700>;
+				clocks = <&topckgen CLK_TOP_SSUSB_PHY_P3_REF>;
+				clock-names = "ref";
+				#phy-cells = <1>;
+			};
+		};
+
+		i2c5: i2c@11d00000 {
+			compatible = "mediatek,mt8195-i2c",
+				     "mediatek,mt8192-i2c";
+			reg = <0 0x11d00000 0 0x1000>,
+			      <0 0x10220580 0 0x80>;
+			interrupts = <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH 0>;
+			clock-div = <1>;
+			clocks = <&imp_iic_wrap_s CLK_IMP_IIC_WRAP_S_I2C5>,
+				 <&infracfg_ao CLK_INFRA_AO_APDMA_B>;
+			clock-names = "main", "dma";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i2c6: i2c@11d01000 {
+			compatible = "mediatek,mt8195-i2c",
+				     "mediatek,mt8192-i2c";
+			reg = <0 0x11d01000 0 0x1000>,
+			      <0 0x10220600 0 0x80>;
+			interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH 0>;
+			clock-div = <1>;
+			clocks = <&imp_iic_wrap_s CLK_IMP_IIC_WRAP_S_I2C6>,
+				 <&infracfg_ao CLK_INFRA_AO_APDMA_B>;
+			clock-names = "main", "dma";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i2c7: i2c@11d02000 {
+			compatible = "mediatek,mt8195-i2c",
+				     "mediatek,mt8192-i2c";
+			reg = <0 0x11d02000 0 0x1000>,
+			      <0 0x10220680 0 0x80>;
+			interrupts = <GIC_SPI 156 IRQ_TYPE_LEVEL_HIGH 0>;
+			clock-div = <1>;
+			clocks = <&imp_iic_wrap_s CLK_IMP_IIC_WRAP_S_I2C7>,
+				 <&infracfg_ao CLK_INFRA_AO_APDMA_B>;
+			clock-names = "main", "dma";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		imp_iic_wrap_s: clock-controller@11d03000 {
+			compatible = "mediatek,mt8195-imp_iic_wrap_s";
+			reg = <0 0x11d03000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
+		i2c0: i2c@11e00000 {
+			compatible = "mediatek,mt8195-i2c",
+				     "mediatek,mt8192-i2c";
+			reg = <0 0x11e00000 0 0x1000>,
+			      <0 0x10220080 0 0x80>;
+			interrupts = <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH 0>;
+			clock-div = <1>;
+			clocks = <&imp_iic_wrap_w CLK_IMP_IIC_WRAP_W_I2C0>,
+				 <&infracfg_ao CLK_INFRA_AO_APDMA_B>;
+			clock-names = "main", "dma";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i2c1: i2c@11e01000 {
+			compatible = "mediatek,mt8195-i2c",
+				     "mediatek,mt8192-i2c";
+			reg = <0 0x11e01000 0 0x1000>,
+			      <0 0x10220200 0 0x80>;
+			interrupts = <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH 0>;
+			clock-div = <1>;
+			clocks = <&imp_iic_wrap_w CLK_IMP_IIC_WRAP_W_I2C1>,
+				 <&infracfg_ao CLK_INFRA_AO_APDMA_B>;
+			clock-names = "main", "dma";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i2c2: i2c@11e02000 {
+			compatible = "mediatek,mt8195-i2c",
+				     "mediatek,mt8192-i2c";
+			reg = <0 0x11e02000 0 0x1000>,
+			      <0 0x10220380 0 0x80>;
+			interrupts = <GIC_SPI 150 IRQ_TYPE_LEVEL_HIGH 0>;
+			clock-div = <1>;
+			clocks = <&imp_iic_wrap_w CLK_IMP_IIC_WRAP_W_I2C2>,
+				 <&infracfg_ao CLK_INFRA_AO_APDMA_B>;
+			clock-names = "main", "dma";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i2c3: i2c@11e03000 {
+			compatible = "mediatek,mt8195-i2c",
+				     "mediatek,mt8192-i2c";
+			reg = <0 0x11e03000 0 0x1000>,
+			      <0 0x10220480 0 0x80>;
+			interrupts = <GIC_SPI 152 IRQ_TYPE_LEVEL_HIGH 0>;
+			clock-div = <1>;
+			clocks = <&imp_iic_wrap_w CLK_IMP_IIC_WRAP_W_I2C3>,
+				 <&infracfg_ao CLK_INFRA_AO_APDMA_B>;
+			clock-names = "main", "dma";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i2c4: i2c@11e04000 {
+			compatible = "mediatek,mt8195-i2c",
+				     "mediatek,mt8192-i2c";
+			reg = <0 0x11e04000 0 0x1000>,
+			      <0 0x10220500 0 0x80>;
+			interrupts = <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH 0>;
+			clock-div = <1>;
+			clocks = <&imp_iic_wrap_w CLK_IMP_IIC_WRAP_W_I2C4>,
+				 <&infracfg_ao CLK_INFRA_AO_APDMA_B>;
+			clock-names = "main", "dma";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		imp_iic_wrap_w: clock-controller@11e05000 {
+			compatible = "mediatek,mt8195-imp_iic_wrap_w";
+			reg = <0 0x11e05000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
+		u3phy1: t-phy@11e30000 {
+			compatible = "mediatek,mt8195-tphy", "mediatek,generic-tphy-v3";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0 0x11e30000 0xe00>;
+			status = "disabled";
+
+			u2port1: usb-phy@0 {
+				reg = <0x0 0x700>;
+				clocks = <&topckgen CLK_TOP_SSUSB_PHY_P1_REF>,
+					 <&clk26m>;
+				clock-names = "ref", "da_ref";
+				#phy-cells = <1>;
+			};
+
+			u3port1: usb-phy@700 {
+				reg = <0x700 0x700>;
+				clocks = <&apmixedsys CLK_APMIXED_PLL_SSUSB26M>,
+					 <&topckgen CLK_TOP_SSUSB_PHY_P1_REF>;
+				clock-names = "ref", "da_ref";
+				nvmem-cells = <&comb_intr_p1>,
+					      <&comb_rx_imp_p1>,
+					      <&comb_tx_imp_p1>;
+				nvmem-cell-names = "intr", "rx_imp", "tx_imp";
+				#phy-cells = <1>;
+			};
+		};
+
+		u3phy0: t-phy@11e40000 {
+			compatible = "mediatek,mt8195-tphy", "mediatek,generic-tphy-v3";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0 0x11e40000 0xe00>;
+			status = "disabled";
+
+			u2port0: usb-phy@0 {
+				reg = <0x0 0x700>;
+				clocks = <&topckgen CLK_TOP_SSUSB_PHY_REF>,
+					 <&clk26m>;
+				clock-names = "ref", "da_ref";
+				#phy-cells = <1>;
+			};
+
+			u3port0: usb-phy@700 {
+				reg = <0x700 0x700>;
+				clocks = <&apmixedsys CLK_APMIXED_PLL_SSUSB26M>,
+					 <&topckgen CLK_TOP_SSUSB_PHY_REF>;
+				clock-names = "ref", "da_ref";
+				nvmem-cells = <&u3_intr_p0>,
+					      <&u3_rx_imp_p0>,
+					      <&u3_tx_imp_p0>;
+				nvmem-cell-names = "intr", "rx_imp", "tx_imp";
+				#phy-cells = <1>;
+			};
+		};
+
+		ufsphy: ufs-phy@11fa0000 {
+			compatible = "mediatek,mt8195-ufsphy", "mediatek,mt8183-ufsphy";
+			reg = <0 0x11fa0000 0 0xc000>;
+			clocks = <&clk26m>, <&clk26m>;
+			clock-names = "unipro", "mp";
+			#phy-cells = <0>;
+			status = "disabled";
+		};
+
+		mfgcfg: clock-controller@13fbf000 {
+			compatible = "mediatek,mt8195-mfgcfg";
+			reg = <0 0x13fbf000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
+		vppsys0: clock-controller@14000000 {
+			compatible = "mediatek,mt8195-vppsys0";
+			reg = <0 0x14000000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
+		smi_sub_common_vpp0_vpp1_2x1: smi@14010000 {
+			compatible = "mediatek,mt8195-smi-sub-common";
+			reg = <0 0x14010000 0 0x1000>;
+			clocks = <&vppsys0 CLK_VPP0_GALS_VPP1_WPE>,
+			       <&vppsys0 CLK_VPP0_GALS_VPP1_WPE>,
+			       <&vppsys0 CLK_VPP0_GALS_VPP1_WPE>;
+			clock-names = "apb", "smi", "gals0";
+			mediatek,smi = <&smi_common_vpp>;
+			power-domains = <&spm MT8195_POWER_DOMAIN_VPPSYS0>;
+		};
+
+		smi_sub_common_vdec_vpp0_2x1: smi@14011000 {
+			compatible = "mediatek,mt8195-smi-sub-common";
+			reg = <0 0x14011000 0 0x1000>;
+			clocks = <&vppsys0 CLK_VPP0_GALS_VDEC_VDEC_CORE1>,
+				 <&vppsys0 CLK_VPP0_GALS_VDEC_VDEC_CORE1>,
+				 <&vppsys0 CLK_VPP0_GALS_VDEC_VDEC_CORE1>;
+			clock-names = "apb", "smi", "gals0";
+			mediatek,smi = <&smi_common_vpp>;
+			power-domains = <&spm MT8195_POWER_DOMAIN_VPPSYS0>;
+		};
+
+		smi_common_vpp: smi@14012000 {
+			compatible = "mediatek,mt8195-smi-common-vpp";
+			reg = <0 0x14012000 0 0x1000>;
+			clocks = <&vppsys0 CLK_VPP0_SMI_COMMON_LARB4>,
+			       <&vppsys0 CLK_VPP0_SMI_COMMON_LARB4>,
+			       <&vppsys0 CLK_VPP0_SMI_RSI>,
+			       <&vppsys0 CLK_VPP0_SMI_RSI>;
+			clock-names = "apb", "smi", "gals0", "gals1";
+			power-domains = <&spm MT8195_POWER_DOMAIN_VPPSYS0>;
+		};
+
+		larb4: larb@14013000 {
+			compatible = "mediatek,mt8195-smi-larb";
+			reg = <0 0x14013000 0 0x1000>;
+			mediatek,larb-id = <4>;
+			mediatek,smi = <&smi_sub_common_vpp0_vpp1_2x1>;
+			clocks = <&vppsys0 CLK_VPP0_GALS_VPP1_WPE>,
+			       <&vppsys0 CLK_VPP0_SMI_COMMON_LARB4>;
+			clock-names = "apb", "smi";
+			power-domains = <&spm MT8195_POWER_DOMAIN_VPPSYS0>;
+		};
+
+		iommu_vpp: iommu@14018000 {
+			compatible = "mediatek,mt8195-iommu-vpp";
+			reg = <0 0x14018000 0 0x1000>;
+			mediatek,larbs = <&larb1 &larb3 &larb4 &larb6 &larb8
+					  &larb12 &larb14 &larb16 &larb18
+					  &larb20 &larb22 &larb23 &larb26
+					  &larb27>;
+			interrupts = <GIC_SPI 594 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&vppsys0 CLK_VPP0_SMI_IOMMU>;
+			clock-names = "bclk";
+			#iommu-cells = <1>;
+			power-domains = <&spm MT8195_POWER_DOMAIN_VPPSYS0>;
+		};
+
+		wpesys: clock-controller@14e00000 {
+			compatible = "mediatek,mt8195-wpesys";
+			reg = <0 0x14e00000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
+		wpesys_vpp0: clock-controller@14e02000 {
+			compatible = "mediatek,mt8195-wpesys_vpp0";
+			reg = <0 0x14e02000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
+		wpesys_vpp1: clock-controller@14e03000 {
+			compatible = "mediatek,mt8195-wpesys_vpp1";
+			reg = <0 0x14e03000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
+		larb7: larb@14e04000 {
+			compatible = "mediatek,mt8195-smi-larb";
+			reg = <0 0x14e04000 0 0x1000>;
+			mediatek,larb-id = <7>;
+			mediatek,smi = <&smi_common_vdo>;
+			clocks = <&wpesys CLK_WPE_SMI_LARB7>,
+				 <&wpesys CLK_WPE_SMI_LARB7>;
+			clock-names = "apb", "smi";
+			power-domains = <&spm MT8195_POWER_DOMAIN_WPESYS>;
+		};
+
+		larb8: larb@14e05000 {
+			compatible = "mediatek,mt8195-smi-larb";
+			reg = <0 0x14e05000 0 0x1000>;
+			mediatek,larb-id = <8>;
+			mediatek,smi = <&smi_common_vpp>;
+			clocks = <&wpesys CLK_WPE_SMI_LARB8>,
+			       <&wpesys CLK_WPE_SMI_LARB8>,
+			       <&vppsys0 CLK_VPP0_GALS_VPP1_WPE>;
+			clock-names = "apb", "smi", "gals";
+			power-domains = <&spm MT8195_POWER_DOMAIN_WPESYS>;
+		};
+
+		vppsys1: clock-controller@14f00000 {
+			compatible = "mediatek,mt8195-vppsys1";
+			reg = <0 0x14f00000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
+		larb5: larb@14f02000 {
+			compatible = "mediatek,mt8195-smi-larb";
+			reg = <0 0x14f02000 0 0x1000>;
+			mediatek,larb-id = <5>;
+			mediatek,smi = <&smi_common_vdo>;
+			clocks = <&vppsys1 CLK_VPP1_VPPSYS1_LARB>,
+			       <&vppsys1 CLK_VPP1_VPPSYS1_GALS>,
+			       <&vppsys0 CLK_VPP0_GALS_VPP1_LARB5>;
+			clock-names = "apb", "smi", "gals";
+			power-domains = <&spm MT8195_POWER_DOMAIN_VPPSYS1>;
+		};
+
+		larb6: larb@14f03000 {
+			compatible = "mediatek,mt8195-smi-larb";
+			reg = <0 0x14f03000 0 0x1000>;
+			mediatek,larb-id = <6>;
+			mediatek,smi = <&smi_sub_common_vpp0_vpp1_2x1>;
+			clocks = <&vppsys1 CLK_VPP1_VPPSYS1_LARB>,
+			       <&vppsys1 CLK_VPP1_VPPSYS1_GALS>,
+			       <&vppsys0 CLK_VPP0_GALS_VPP1_LARB6>;
+			clock-names = "apb", "smi", "gals";
+			power-domains = <&spm MT8195_POWER_DOMAIN_VPPSYS1>;
+		};
+
+		imgsys: clock-controller@15000000 {
+			compatible = "mediatek,mt8195-imgsys";
+			reg = <0 0x15000000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
+		larb9: larb@15001000 {
+			compatible = "mediatek,mt8195-smi-larb";
+			reg = <0 0x15001000 0 0x1000>;
+			mediatek,larb-id = <9>;
+			mediatek,smi = <&smi_sub_common_img1_3x1>;
+			clocks = <&imgsys CLK_IMG_LARB9>,
+				 <&imgsys CLK_IMG_LARB9>,
+				 <&imgsys CLK_IMG_GALS>;
+			clock-names = "apb", "smi", "gals";
+			power-domains = <&spm MT8195_POWER_DOMAIN_IMG>;
+		};
+
+		smi_sub_common_img0_3x1: smi@15002000 {
+			compatible = "mediatek,mt8195-smi-sub-common";
+			reg = <0 0x15002000 0 0x1000>;
+			clocks = <&imgsys CLK_IMG_IPE>,
+				 <&imgsys CLK_IMG_IPE>,
+				 <&vppsys0 CLK_VPP0_GALS_IMGSYS_CAMSYS>;
+			clock-names = "apb", "smi", "gals0";
+			mediatek,smi = <&smi_common_vpp>;
+			power-domains = <&spm MT8195_POWER_DOMAIN_IMG>;
+		};
+
+		smi_sub_common_img1_3x1: smi@15003000 {
+			compatible = "mediatek,mt8195-smi-sub-common";
+			reg = <0 0x15003000 0 0x1000>;
+			clocks = <&imgsys CLK_IMG_LARB9>,
+				 <&imgsys CLK_IMG_LARB9>,
+				 <&imgsys CLK_IMG_GALS>;
+			clock-names = "apb", "smi", "gals0";
+			mediatek,smi = <&smi_common_vdo>;
+			power-domains = <&spm MT8195_POWER_DOMAIN_IMG>;
+		};
+
+		imgsys1_dip_top: clock-controller@15110000 {
+			compatible = "mediatek,mt8195-imgsys1_dip_top";
+			reg = <0 0x15110000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
+		larb10: larb@15120000 {
+			compatible = "mediatek,mt8195-smi-larb";
+			reg = <0 0x15120000 0 0x1000>;
+			mediatek,larb-id = <10>;
+			mediatek,smi = <&smi_sub_common_img1_3x1>;
+			clocks = <&imgsys CLK_IMG_DIP0>,
+			       <&imgsys1_dip_top CLK_IMG1_DIP_TOP_LARB10>;
+			clock-names = "apb", "smi";
+			power-domains = <&spm MT8195_POWER_DOMAIN_DIP>;
+		};
+
+		imgsys1_dip_nr: clock-controller@15130000 {
+			compatible = "mediatek,mt8195-imgsys1_dip_nr";
+			reg = <0 0x15130000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
+		imgsys1_wpe: clock-controller@15220000 {
+			compatible = "mediatek,mt8195-imgsys1_wpe";
+			reg = <0 0x15220000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
+		larb11: larb@15230000 {
+			compatible = "mediatek,mt8195-smi-larb";
+			reg = <0 0x15230000 0 0x1000>;
+			mediatek,larb-id = <11>;
+			mediatek,smi = <&smi_sub_common_img1_3x1>;
+			clocks = <&imgsys CLK_IMG_WPE0>,
+			       <&imgsys1_wpe CLK_IMG1_WPE_LARB11>;
+			clock-names = "apb", "smi";
+			power-domains = <&spm MT8195_POWER_DOMAIN_DIP>;
+		};
+
+		ipesys: clock-controller@15330000 {
+			compatible = "mediatek,mt8195-ipesys";
+			reg = <0 0x15330000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
+		larb12: larb@15340000 {
+			compatible = "mediatek,mt8195-smi-larb";
+			reg = <0 0x15340000 0 0x1000>;
+			mediatek,larb-id = <12>;
+			mediatek,smi = <&smi_sub_common_img0_3x1>;
+			clocks = <&ipesys CLK_IPE_SMI_LARB12>,
+				 <&ipesys CLK_IPE_SMI_LARB12>;
+			clock-names = "apb", "smi";
+			power-domains = <&spm MT8195_POWER_DOMAIN_IPE>;
+		};
+
+		camsys: clock-controller@16000000 {
+			compatible = "mediatek,mt8195-camsys";
+			reg = <0 0x16000000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
+		larb13: larb@16001000 {
+			compatible = "mediatek,mt8195-smi-larb";
+			reg = <0 0x16001000 0 0x1000>;
+			mediatek,larb-id = <13>;
+			mediatek,smi = <&smi_sub_common_cam_4x1>;
+			clocks = <&camsys CLK_CAM_LARB13>,
+			       <&camsys CLK_CAM_LARB13>,
+			       <&camsys CLK_CAM_CAM2MM0_GALS>;
+			clock-names = "apb", "smi", "gals";
+			power-domains = <&spm MT8195_POWER_DOMAIN_CAM>;
+		};
+
+		larb14: larb@16002000 {
+			compatible = "mediatek,mt8195-smi-larb";
+			reg = <0 0x16002000 0 0x1000>;
+			mediatek,larb-id = <14>;
+			mediatek,smi = <&smi_sub_common_cam_7x1>;
+			clocks = <&camsys CLK_CAM_LARB14>,
+				 <&camsys CLK_CAM_LARB14>;
+			clock-names = "apb", "smi";
+			power-domains = <&spm MT8195_POWER_DOMAIN_CAM>;
+		};
+
+		smi_sub_common_cam_4x1: smi@16004000 {
+			compatible = "mediatek,mt8195-smi-sub-common";
+			reg = <0 0x16004000 0 0x1000>;
+			clocks = <&camsys CLK_CAM_LARB13>,
+				 <&camsys CLK_CAM_LARB13>,
+				 <&camsys CLK_CAM_CAM2MM0_GALS>;
+			clock-names = "apb", "smi", "gals0";
+			mediatek,smi = <&smi_common_vdo>;
+			power-domains = <&spm MT8195_POWER_DOMAIN_CAM>;
+		};
+
+		smi_sub_common_cam_7x1: smi@16005000 {
+			compatible = "mediatek,mt8195-smi-sub-common";
+			reg = <0 0x16005000 0 0x1000>;
+			clocks = <&camsys CLK_CAM_LARB14>,
+				 <&camsys CLK_CAM_CAM2MM1_GALS>,
+				 <&vppsys0 CLK_VPP0_GALS_IMGSYS_CAMSYS>;
+			clock-names = "apb", "smi", "gals0";
+			mediatek,smi = <&smi_common_vpp>;
+			power-domains = <&spm MT8195_POWER_DOMAIN_CAM>;
+		};
+
+		larb16: larb@16012000 {
+			compatible = "mediatek,mt8195-smi-larb";
+			reg = <0 0x16012000 0 0x1000>;
+			mediatek,larb-id = <16>;
+			mediatek,smi = <&smi_sub_common_cam_7x1>;
+			clocks = <&camsys_rawa CLK_CAM_RAWA_LARBX>,
+				 <&camsys_rawa CLK_CAM_RAWA_LARBX>;
+			clock-names = "apb", "smi";
+			power-domains = <&spm MT8195_POWER_DOMAIN_CAM_RAWA>;
+		};
+
+		larb17: larb@16013000 {
+			compatible = "mediatek,mt8195-smi-larb";
+			reg = <0 0x16013000 0 0x1000>;
+			mediatek,larb-id = <17>;
+			mediatek,smi = <&smi_sub_common_cam_4x1>;
+			clocks = <&camsys_yuva CLK_CAM_YUVA_LARBX>,
+				 <&camsys_yuva CLK_CAM_YUVA_LARBX>;
+			clock-names = "apb", "smi";
+			power-domains = <&spm MT8195_POWER_DOMAIN_CAM_RAWA>;
+		};
+
+		larb27: larb@16014000 {
+			compatible = "mediatek,mt8195-smi-larb";
+			reg = <0 0x16014000 0 0x1000>;
+			mediatek,larb-id = <27>;
+			mediatek,smi = <&smi_sub_common_cam_7x1>;
+			clocks = <&camsys_rawb CLK_CAM_RAWB_LARBX>,
+				 <&camsys_rawb CLK_CAM_RAWB_LARBX>;
+			clock-names = "apb", "smi";
+			power-domains = <&spm MT8195_POWER_DOMAIN_CAM_RAWB>;
+		};
+
+		larb28: larb@16015000 {
+			compatible = "mediatek,mt8195-smi-larb";
+			reg = <0 0x16015000 0 0x1000>;
+			mediatek,larb-id = <28>;
+			mediatek,smi = <&smi_sub_common_cam_4x1>;
+			clocks = <&camsys_yuvb CLK_CAM_YUVB_LARBX>,
+				 <&camsys_yuvb CLK_CAM_YUVB_LARBX>;
+			clock-names = "apb", "smi";
+			power-domains = <&spm MT8195_POWER_DOMAIN_CAM_RAWB>;
+		};
+
+		camsys_rawa: clock-controller@1604f000 {
+			compatible = "mediatek,mt8195-camsys_rawa";
+			reg = <0 0x1604f000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
+		camsys_yuva: clock-controller@1606f000 {
+			compatible = "mediatek,mt8195-camsys_yuva";
+			reg = <0 0x1606f000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
+		camsys_rawb: clock-controller@1608f000 {
+			compatible = "mediatek,mt8195-camsys_rawb";
+			reg = <0 0x1608f000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
+		camsys_yuvb: clock-controller@160af000 {
+			compatible = "mediatek,mt8195-camsys_yuvb";
+			reg = <0 0x160af000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
+		camsys_mraw: clock-controller@16140000 {
+			compatible = "mediatek,mt8195-camsys_mraw";
+			reg = <0 0x16140000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
+		larb25: larb@16141000 {
+			compatible = "mediatek,mt8195-smi-larb";
+			reg = <0 0x16141000 0 0x1000>;
+			mediatek,larb-id = <25>;
+			mediatek,smi = <&smi_sub_common_cam_4x1>;
+			clocks = <&camsys CLK_CAM_LARB13>,
+				 <&camsys_mraw CLK_CAM_MRAW_LARBX>,
+				 <&camsys CLK_CAM_CAM2MM0_GALS>;
+			clock-names = "apb", "smi", "gals";
+			power-domains = <&spm MT8195_POWER_DOMAIN_CAM_MRAW>;
+		};
+
+		larb26: larb@16142000 {
+			compatible = "mediatek,mt8195-smi-larb";
+			reg = <0 0x16142000 0 0x1000>;
+			mediatek,larb-id = <26>;
+			mediatek,smi = <&smi_sub_common_cam_7x1>;
+			clocks = <&camsys_mraw CLK_CAM_MRAW_LARBX>,
+				 <&camsys_mraw CLK_CAM_MRAW_LARBX>;
+			clock-names = "apb", "smi";
+			power-domains = <&spm MT8195_POWER_DOMAIN_CAM_MRAW>;
+
+		};
+
+		ccusys: clock-controller@17200000 {
+			compatible = "mediatek,mt8195-ccusys";
+			reg = <0 0x17200000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
+		larb18: larb@17201000 {
+			compatible = "mediatek,mt8195-smi-larb";
+			reg = <0 0x17201000 0 0x1000>;
+			mediatek,larb-id = <18>;
+			mediatek,smi = <&smi_sub_common_cam_7x1>;
+			clocks = <&ccusys CLK_CCU_LARB18>,
+				 <&ccusys CLK_CCU_LARB18>;
+			clock-names = "apb", "smi";
+			power-domains = <&spm MT8195_POWER_DOMAIN_CAM>;
+		};
+
+		larb24: larb@1800d000 {
+			compatible = "mediatek,mt8195-smi-larb";
+			reg = <0 0x1800d000 0 0x1000>;
+			mediatek,larb-id = <24>;
+			mediatek,smi = <&smi_common_vdo>;
+			clocks = <&vdecsys_soc CLK_VDEC_SOC_LARB1>,
+				 <&vdecsys_soc CLK_VDEC_SOC_LARB1>;
+			clock-names = "apb", "smi";
+			power-domains = <&spm MT8195_POWER_DOMAIN_VDEC0>;
+		};
+
+		larb23: larb@1800e000 {
+			compatible = "mediatek,mt8195-smi-larb";
+			reg = <0 0x1800e000 0 0x1000>;
+			mediatek,larb-id = <23>;
+			mediatek,smi = <&smi_sub_common_vdec_vpp0_2x1>;
+			clocks = <&vppsys0 CLK_VPP0_GALS_VDEC_VDEC_CORE1>,
+				 <&vdecsys_soc CLK_VDEC_SOC_LARB1>;
+			clock-names = "apb", "smi";
+			power-domains = <&spm MT8195_POWER_DOMAIN_VDEC0>;
+		};
+
+		vdecsys_soc: clock-controller@1800f000 {
+			compatible = "mediatek,mt8195-vdecsys_soc";
+			reg = <0 0x1800f000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
+		larb21: larb@1802e000 {
+			compatible = "mediatek,mt8195-smi-larb";
+			reg = <0 0x1802e000 0 0x1000>;
+			mediatek,larb-id = <21>;
+			mediatek,smi = <&smi_common_vdo>;
+			clocks = <&vdecsys CLK_VDEC_LARB1>,
+				 <&vdecsys CLK_VDEC_LARB1>;
+			clock-names = "apb", "smi";
+			power-domains = <&spm MT8195_POWER_DOMAIN_VDEC1>;
+		};
+
+		vdecsys: clock-controller@1802f000 {
+			compatible = "mediatek,mt8195-vdecsys";
+			reg = <0 0x1802f000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
+		larb22: larb@1803e000 {
+			compatible = "mediatek,mt8195-smi-larb";
+			reg = <0 0x1803e000 0 0x1000>;
+			mediatek,larb-id = <22>;
+			mediatek,smi = <&smi_sub_common_vdec_vpp0_2x1>;
+			clocks = <&vppsys0 CLK_VPP0_GALS_VDEC_VDEC_CORE1>,
+				 <&vdecsys_core1 CLK_VDEC_CORE1_LARB1>;
+			clock-names = "apb", "smi";
+			power-domains = <&spm MT8195_POWER_DOMAIN_VDEC2>;
+		};
+
+		vdecsys_core1: clock-controller@1803f000 {
+			compatible = "mediatek,mt8195-vdecsys_core1";
+			reg = <0 0x1803f000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
+		apusys_pll: clock-controller@190f3000 {
+			compatible = "mediatek,mt8195-apusys_pll";
+			reg = <0 0x190f3000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
+		vencsys: clock-controller@1a000000 {
+			compatible = "mediatek,mt8195-vencsys";
+			reg = <0 0x1a000000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
+		larb19: larb@1a010000 {
+			compatible = "mediatek,mt8195-smi-larb";
+			reg = <0 0x1a010000 0 0x1000>;
+			mediatek,larb-id = <19>;
+			mediatek,smi = <&smi_common_vdo>;
+			clocks = <&vencsys CLK_VENC_VENC>,
+				 <&vencsys CLK_VENC_GALS>;
+			clock-names = "apb", "smi";
+			power-domains = <&spm MT8195_POWER_DOMAIN_VENC>;
+		};
+
+		vencsys_core1: clock-controller@1b000000 {
+			compatible = "mediatek,mt8195-vencsys_core1";
+			reg = <0 0x1b000000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
+		vdosys0: syscon@1c01a000 {
+			compatible = "mediatek,mt8195-mmsys", "syscon";
+			reg = <0 0x1c01a000 0 0x1000>;
+			mboxes = <&gce0 0 CMDQ_THR_PRIO_4>;
+			#clock-cells = <1>;
+		};
+
+		larb20: larb@1b010000 {
+			compatible = "mediatek,mt8195-smi-larb";
+			reg = <0 0x1b010000 0 0x1000>;
+			mediatek,larb-id = <20>;
+			mediatek,smi = <&smi_common_vpp>;
+			clocks = <&vencsys_core1 CLK_VENC_CORE1_LARB>,
+				 <&vencsys_core1 CLK_VENC_CORE1_GALS>,
+				 <&vppsys0 CLK_VPP0_GALS_VDO0_VDO1_VENCSYS_CORE1>;
+			clock-names = "apb", "smi", "gals";
+			power-domains = <&spm MT8195_POWER_DOMAIN_VENC_CORE1>;
+		};
+
+		ovl0: ovl@1c000000 {
+			compatible = "mediatek,mt8195-disp-ovl", "mediatek,mt8183-disp-ovl";
+			reg = <0 0x1c000000 0 0x1000>;
+			interrupts = <GIC_SPI 636 IRQ_TYPE_LEVEL_HIGH 0>;
+			power-domains = <&spm MT8195_POWER_DOMAIN_VDOSYS0>;
+			clocks = <&vdosys0 CLK_VDO0_DISP_OVL0>;
+			iommus = <&iommu_vdo M4U_PORT_L0_DISP_OVL0_RDMA0>;
+			mediatek,gce-client-reg = <&gce0 SUBSYS_1c00XXXX 0x0000 0x1000>;
+		};
+
+		rdma0: rdma@1c002000 {
+			compatible = "mediatek,mt8195-disp-rdma";
+			reg = <0 0x1c002000 0 0x1000>;
+			interrupts = <GIC_SPI 638 IRQ_TYPE_LEVEL_HIGH 0>;
+			power-domains = <&spm MT8195_POWER_DOMAIN_VDOSYS0>;
+			clocks = <&vdosys0 CLK_VDO0_DISP_RDMA0>;
+			iommus = <&iommu_vdo M4U_PORT_L0_DISP_RDMA0>;
+			mediatek,gce-client-reg = <&gce0 SUBSYS_1c00XXXX 0x2000 0x1000>;
+		};
+
+		color0: color@1c003000 {
+			compatible = "mediatek,mt8195-disp-color", "mediatek,mt8173-disp-color";
+			reg = <0 0x1c003000 0 0x1000>;
+			interrupts = <GIC_SPI 639 IRQ_TYPE_LEVEL_HIGH 0>;
+			power-domains = <&spm MT8195_POWER_DOMAIN_VDOSYS0>;
+			clocks = <&vdosys0 CLK_VDO0_DISP_COLOR0>;
+			mediatek,gce-client-reg = <&gce0 SUBSYS_1c00XXXX 0x3000 0x1000>;
+		};
+
+		ccorr0: ccorr@1c004000 {
+			compatible = "mediatek,mt8195-disp-ccorr", "mediatek,mt8192-disp-ccorr";
+			reg = <0 0x1c004000 0 0x1000>;
+			interrupts = <GIC_SPI 640 IRQ_TYPE_LEVEL_HIGH 0>;
+			power-domains = <&spm MT8195_POWER_DOMAIN_VDOSYS0>;
+			clocks = <&vdosys0 CLK_VDO0_DISP_CCORR0>;
+			mediatek,gce-client-reg = <&gce0 SUBSYS_1c00XXXX 0x4000 0x1000>;
+		};
+
+		aal0: aal@1c005000 {
+			compatible = "mediatek,mt8195-disp-aal", "mediatek,mt8183-disp-aal";
+			reg = <0 0x1c005000 0 0x1000>;
+			interrupts = <GIC_SPI 641 IRQ_TYPE_LEVEL_HIGH 0>;
+			power-domains = <&spm MT8195_POWER_DOMAIN_VDOSYS0>;
+			clocks = <&vdosys0 CLK_VDO0_DISP_AAL0>;
+			mediatek,gce-client-reg = <&gce0 SUBSYS_1c00XXXX 0x5000 0x1000>;
+		};
+
+		gamma0: gamma@1c006000 {
+			compatible = "mediatek,mt8195-disp-gamma", "mediatek,mt8183-disp-gamma";
+			reg = <0 0x1c006000 0 0x1000>;
+			interrupts = <GIC_SPI 642 IRQ_TYPE_LEVEL_HIGH 0>;
+			power-domains = <&spm MT8195_POWER_DOMAIN_VDOSYS0>;
+			clocks = <&vdosys0 CLK_VDO0_DISP_GAMMA0>;
+			mediatek,gce-client-reg = <&gce0 SUBSYS_1c00XXXX 0x6000 0x1000>;
+		};
+
+		dither0: dither@1c007000 {
+			compatible = "mediatek,mt8195-disp-dither", "mediatek,mt8183-disp-dither";
+			reg = <0 0x1c007000 0 0x1000>;
+			interrupts = <GIC_SPI 643 IRQ_TYPE_LEVEL_HIGH 0>;
+			power-domains = <&spm MT8195_POWER_DOMAIN_VDOSYS0>;
+			clocks = <&vdosys0 CLK_VDO0_DISP_DITHER0>;
+			mediatek,gce-client-reg = <&gce0 SUBSYS_1c00XXXX 0x7000 0x1000>;
+		};
+
+		dsc0: dsc@1c009000 {
+			compatible = "mediatek,mt8195-disp-dsc";
+			reg = <0 0x1c009000 0 0x1000>;
+			interrupts = <GIC_SPI 645 IRQ_TYPE_LEVEL_HIGH 0>;
+			power-domains = <&spm MT8195_POWER_DOMAIN_VDOSYS0>;
+			clocks = <&vdosys0 CLK_VDO0_DSC_WRAP0>;
+			mediatek,gce-client-reg = <&gce0 SUBSYS_1c00XXXX 0x9000 0x1000>;
+		};
+
+		merge0: merge@1c014000 {
+			compatible = "mediatek,mt8195-disp-merge";
+			reg = <0 0x1c014000 0 0x1000>;
+			interrupts = <GIC_SPI 656 IRQ_TYPE_LEVEL_HIGH 0>;
+			power-domains = <&spm MT8195_POWER_DOMAIN_VDOSYS0>;
+			clocks = <&vdosys0 CLK_VDO0_VPP_MERGE0>;
+			mediatek,gce-client-reg = <&gce0 SUBSYS_1c01XXXX 0x4000 0x1000>;
+		};
+
+		mutex: mutex@1c016000 {
+			compatible = "mediatek,mt8195-disp-mutex";
+			reg = <0 0x1c016000 0 0x1000>;
+			interrupts = <GIC_SPI 658 IRQ_TYPE_LEVEL_HIGH 0>;
+			power-domains = <&spm MT8195_POWER_DOMAIN_VDOSYS0>;
+			clocks = <&vdosys0 CLK_VDO0_DISP_MUTEX0>;
+			mediatek,gce-events = <CMDQ_EVENT_VDO0_DISP_STREAM_DONE_0>;
+		};
+
+		larb0: larb@1c018000 {
+			compatible = "mediatek,mt8195-smi-larb";
+			reg = <0 0x1c018000 0 0x1000>;
+			mediatek,larb-id = <0>;
+			mediatek,smi = <&smi_common_vdo>;
+			clocks = <&vdosys0 CLK_VDO0_SMI_LARB>,
+				 <&vdosys0 CLK_VDO0_SMI_LARB>,
+				 <&vppsys0 CLK_VPP0_GALS_VDO0_LARB0>;
+			clock-names = "apb", "smi", "gals";
+			power-domains = <&spm MT8195_POWER_DOMAIN_VDOSYS0>;
+		};
+
+		larb1: larb@1c019000 {
+			compatible = "mediatek,mt8195-smi-larb";
+			reg = <0 0x1c019000 0 0x1000>;
+			mediatek,larb-id = <1>;
+			mediatek,smi = <&smi_common_vpp>;
+			clocks = <&vdosys0 CLK_VDO0_SMI_LARB>,
+				 <&vppsys0 CLK_VPP0_GALS_VDO0_VDO1_VENCSYS_CORE1>,
+				 <&vppsys0 CLK_VPP0_GALS_VDO0_LARB1>;
+			clock-names = "apb", "smi", "gals";
+			power-domains = <&spm MT8195_POWER_DOMAIN_VDOSYS0>;
+		};
+
+		vdosys1: syscon@1c100000 {
+			compatible = "mediatek,mt8195-mmsys", "syscon";
+			reg = <0 0x1c100000 0 0x1000>;
+			#clock-cells = <1>;
+		};
+
+		smi_common_vdo: smi@1c01b000 {
+			compatible = "mediatek,mt8195-smi-common-vdo";
+			reg = <0 0x1c01b000 0 0x1000>;
+			clocks = <&vdosys0 CLK_VDO0_SMI_COMMON>,
+				 <&vdosys0 CLK_VDO0_SMI_EMI>,
+				 <&vdosys0 CLK_VDO0_SMI_RSI>,
+				 <&vdosys0 CLK_VDO0_SMI_GALS>;
+			clock-names = "apb", "smi", "gals0", "gals1";
+			power-domains = <&spm MT8195_POWER_DOMAIN_VDOSYS0>;
+
+		};
+
+		iommu_vdo: iommu@1c01f000 {
+			compatible = "mediatek,mt8195-iommu-vdo";
+			reg = <0 0x1c01f000 0 0x1000>;
+			mediatek,larbs = <&larb0 &larb2 &larb5 &larb7 &larb9
+					  &larb10 &larb11 &larb13 &larb17
+					  &larb19 &larb21 &larb24 &larb25
+					  &larb28>;
+			interrupts = <GIC_SPI 669 IRQ_TYPE_LEVEL_HIGH 0>;
+			#iommu-cells = <1>;
+			clocks = <&vdosys0 CLK_VDO0_SMI_IOMMU>;
+			clock-names = "bclk";
+			power-domains = <&spm MT8195_POWER_DOMAIN_VDOSYS0>;
+		};
+
+		larb2: larb@1c102000 {
+			compatible = "mediatek,mt8195-smi-larb";
+			reg = <0 0x1c102000 0 0x1000>;
+			mediatek,larb-id = <2>;
+			mediatek,smi = <&smi_common_vdo>;
+			clocks = <&vdosys1 CLK_VDO1_SMI_LARB2>,
+				 <&vdosys1 CLK_VDO1_SMI_LARB2>,
+				 <&vdosys1 CLK_VDO1_GALS>;
+			clock-names = "apb", "smi", "gals";
+			power-domains = <&spm MT8195_POWER_DOMAIN_VDOSYS1>;
+		};
+
+		larb3: larb@1c103000 {
+			compatible = "mediatek,mt8195-smi-larb";
+			reg = <0 0x1c103000 0 0x1000>;
+			mediatek,larb-id = <3>;
+			mediatek,smi = <&smi_common_vpp>;
+			clocks = <&vdosys1 CLK_VDO1_SMI_LARB3>,
+				 <&vdosys1 CLK_VDO1_GALS>,
+				 <&vppsys0 CLK_VPP0_GALS_VDO0_VDO1_VENCSYS_CORE1>;
+			clock-names = "apb", "smi", "gals";
+			power-domains = <&spm MT8195_POWER_DOMAIN_VDOSYS1>;
+		};
+	};
+};
diff --git a/arch/arm64/boot/dts/mediatek/mt8516.dtsi b/arch/arm64/boot/dts/mediatek/mt8516.dtsi
index bbe5a1419eff..d1b67c82d761 100644
--- a/arch/arm64/boot/dts/mediatek/mt8516.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt8516.dtsi
@@ -345,14 +345,9 @@
 			reg = <0 0x11009000 0 0x90>,
 			      <0 0x11000180 0 0x80>;
 			interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_LOW>;
-			clocks = <&topckgen CLK_TOP_AHB_INFRA_D2>,
-				 <&infracfg CLK_IFR_I2C0_SEL>,
-				 <&topckgen CLK_TOP_I2C0>,
+			clocks = <&topckgen CLK_TOP_I2C0>,
 				 <&topckgen CLK_TOP_APDMA>;
-			clock-names = "main-source",
-				      "main-sel",
-				      "main",
-				      "dma";
+			clock-names = "main", "dma";
 			#address-cells = <1>;
 			#size-cells = <0>;
 			status = "disabled";
@@ -364,14 +359,9 @@
 			reg = <0 0x1100a000 0 0x90>,
 			      <0 0x11000200 0 0x80>;
 			interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_LOW>;
-			clocks = <&topckgen CLK_TOP_AHB_INFRA_D2>,
-				 <&infracfg CLK_IFR_I2C1_SEL>,
-				 <&topckgen CLK_TOP_I2C1>,
+			clocks = <&topckgen CLK_TOP_I2C1>,
 				 <&topckgen CLK_TOP_APDMA>;
-			clock-names = "main-source",
-				      "main-sel",
-				      "main",
-				      "dma";
+			clock-names = "main", "dma";
 			#address-cells = <1>;
 			#size-cells = <0>;
 			status = "disabled";
@@ -383,14 +373,9 @@
 			reg = <0 0x1100b000 0 0x90>,
 			      <0 0x11000280 0 0x80>;
 			interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_LOW>;
-			clocks = <&topckgen CLK_TOP_AHB_INFRA_D2>,
-				 <&infracfg CLK_IFR_I2C2_SEL>,
-				 <&topckgen CLK_TOP_I2C2>,
+			clocks = <&topckgen CLK_TOP_I2C2>,
 				 <&topckgen CLK_TOP_APDMA>;
-			clock-names = "main-source",
-				      "main-sel",
-				      "main",
-				      "dma";
+			clock-names = "main", "dma";
 			#address-cells = <1>;
 			#size-cells = <0>;
 			status = "disabled";
diff --git a/arch/arm64/boot/dts/mediatek/pumpkin-common.dtsi b/arch/arm64/boot/dts/mediatek/pumpkin-common.dtsi
index fcddec14738d..8ee1529683a3 100644
--- a/arch/arm64/boot/dts/mediatek/pumpkin-common.dtsi
+++ b/arch/arm64/boot/dts/mediatek/pumpkin-common.dtsi
@@ -25,11 +25,10 @@
 
 	gpio-keys {
 		compatible = "gpio-keys";
-		input-name = "gpio-keys";
 		pinctrl-names = "default";
 		pinctrl-0 = <&gpio_keys_default>;
 
-		volume-up {
+		key-volume-up {
 			gpios = <&pio 42 GPIO_ACTIVE_LOW>;
 			label = "volume_up";
 			linux,code = <115>;
@@ -37,7 +36,7 @@
 			debounce-interval = <15>;
 		};
 
-		volume-down {
+		key-volume-down {
 			gpios = <&pio 43 GPIO_ACTIVE_LOW>;
 			label = "volume_down";
 			linux,code = <114>;
diff --git a/arch/arm64/boot/dts/microchip/sparx5.dtsi b/arch/arm64/boot/dts/microchip/sparx5.dtsi
index 787ebcec121d..2dd5e38820b1 100644
--- a/arch/arm64/boot/dts/microchip/sparx5.dtsi
+++ b/arch/arm64/boot/dts/microchip/sparx5.dtsi
@@ -471,9 +471,10 @@
 				<0x6 0x10004000 0x7fc000>,
 				<0x6 0x11010000 0xaf0000>;
 			reg-names = "cpu", "dev", "gcb";
-			interrupt-names = "xtr", "fdma";
+			interrupt-names = "xtr", "fdma", "ptp";
 			interrupts =	<GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>,
-					<GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
+					<GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>;
 			resets = <&reset 0>;
 			reset-names = "switch";
 		};
diff --git a/arch/arm64/boot/dts/microchip/sparx5_nand.dtsi b/arch/arm64/boot/dts/microchip/sparx5_nand.dtsi
index 03f107e427d7..ce0747fd6444 100644
--- a/arch/arm64/boot/dts/microchip/sparx5_nand.dtsi
+++ b/arch/arm64/boot/dts/microchip/sparx5_nand.dtsi
@@ -19,7 +19,7 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 		reg = <14>; /* CS14 */
-		spi-flash@6 {
+		flash@6 {
 			compatible = "spi-nand";
 			pinctrl-0 = <&cs14_pins>;
 			pinctrl-names = "default";
diff --git a/arch/arm64/boot/dts/microchip/sparx5_pcb125.dts b/arch/arm64/boot/dts/microchip/sparx5_pcb125.dts
index 9baa085d7861..dbf8c1d48a02 100644
--- a/arch/arm64/boot/dts/microchip/sparx5_pcb125.dts
+++ b/arch/arm64/boot/dts/microchip/sparx5_pcb125.dts
@@ -47,7 +47,7 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 		reg = <0>;	/* CS0 */
-		spi-flash@9 {
+		flash@9 {
 			compatible = "jedec,spi-nor";
 			spi-max-frequency = <8000000>;
 			reg = <0x9>;	/* SPI */
@@ -59,7 +59,7 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 		reg = <1>; /* CS1 */
-		spi-flash@9 {
+		flash@9 {
 			compatible = "spi-nand";
 			pinctrl-0 = <&cs1_pins>;
 			pinctrl-names = "default";
diff --git a/arch/arm64/boot/dts/microchip/sparx5_pcb134_board.dtsi b/arch/arm64/boot/dts/microchip/sparx5_pcb134_board.dtsi
index 33faf1f3264f..bf12be5e8d84 100644
--- a/arch/arm64/boot/dts/microchip/sparx5_pcb134_board.dtsi
+++ b/arch/arm64/boot/dts/microchip/sparx5_pcb134_board.dtsi
@@ -274,7 +274,7 @@
 
 &spi0 {
 	status = "okay";
-	spi-flash@0 {
+	flash@0 {
 		compatible = "jedec,spi-nor";
 		spi-max-frequency = <8000000>;
 		reg = <0>;
@@ -289,7 +289,7 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 		reg = <0>;	/* CS0 */
-		spi-flash@9 {
+		flash@9 {
 			compatible = "jedec,spi-nor";
 			spi-max-frequency = <8000000>;
 			reg = <0x9>;	/* SPI */
@@ -546,164 +546,164 @@
 
 &axi {
 	sfp_eth12: sfp-eth12 {
-		compatible       = "sff,sfp";
-		i2c-bus          = <&i2c_sfp1>;
+		compatible = "sff,sfp";
+		i2c-bus = <&i2c_sfp1>;
 		tx-disable-gpios = <&sgpio_out2 11 1 GPIO_ACTIVE_LOW>;
-		los-gpios        = <&sgpio_in2 11 1 GPIO_ACTIVE_HIGH>;
-		mod-def0-gpios   = <&sgpio_in2 11 2 GPIO_ACTIVE_LOW>;
-		tx-fault-gpios   = <&sgpio_in2 12 0 GPIO_ACTIVE_HIGH>;
+		los-gpios = <&sgpio_in2 11 1 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&sgpio_in2 11 2 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios = <&sgpio_in2 12 0 GPIO_ACTIVE_HIGH>;
 	};
 	sfp_eth13: sfp-eth13 {
-		compatible       = "sff,sfp";
-		i2c-bus          = <&i2c_sfp2>;
+		compatible = "sff,sfp";
+		i2c-bus = <&i2c_sfp2>;
 		tx-disable-gpios = <&sgpio_out2 12 1 GPIO_ACTIVE_LOW>;
-		los-gpios        = <&sgpio_in2 12 1 GPIO_ACTIVE_HIGH>;
-		mod-def0-gpios   = <&sgpio_in2 12 2 GPIO_ACTIVE_LOW>;
-		tx-fault-gpios   = <&sgpio_in2 13 0 GPIO_ACTIVE_HIGH>;
+		los-gpios = <&sgpio_in2 12 1 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&sgpio_in2 12 2 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios = <&sgpio_in2 13 0 GPIO_ACTIVE_HIGH>;
 	};
 	sfp_eth14: sfp-eth14 {
-		compatible       = "sff,sfp";
-		i2c-bus          = <&i2c_sfp3>;
+		compatible = "sff,sfp";
+		i2c-bus = <&i2c_sfp3>;
 		tx-disable-gpios = <&sgpio_out2 13 1 GPIO_ACTIVE_LOW>;
-		los-gpios        = <&sgpio_in2 13 1 GPIO_ACTIVE_HIGH>;
-		mod-def0-gpios   = <&sgpio_in2 13 2 GPIO_ACTIVE_LOW>;
-		tx-fault-gpios   = <&sgpio_in2 14 0 GPIO_ACTIVE_HIGH>;
+		los-gpios = <&sgpio_in2 13 1 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&sgpio_in2 13 2 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios = <&sgpio_in2 14 0 GPIO_ACTIVE_HIGH>;
 	};
 	sfp_eth15: sfp-eth15 {
-		compatible       = "sff,sfp";
-		i2c-bus          = <&i2c_sfp4>;
+		compatible = "sff,sfp";
+		i2c-bus = <&i2c_sfp4>;
 		tx-disable-gpios = <&sgpio_out2 14 1 GPIO_ACTIVE_LOW>;
-		los-gpios        = <&sgpio_in2 14 1 GPIO_ACTIVE_HIGH>;
-		mod-def0-gpios   = <&sgpio_in2 14 2 GPIO_ACTIVE_LOW>;
-		tx-fault-gpios   = <&sgpio_in2 15 0 GPIO_ACTIVE_HIGH>;
+		los-gpios = <&sgpio_in2 14 1 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&sgpio_in2 14 2 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios = <&sgpio_in2 15 0 GPIO_ACTIVE_HIGH>;
 	};
 	sfp_eth48: sfp-eth48 {
-		compatible       = "sff,sfp";
-		i2c-bus          = <&i2c_sfp5>;
+		compatible = "sff,sfp";
+		i2c-bus = <&i2c_sfp5>;
 		tx-disable-gpios = <&sgpio_out2 15 1 GPIO_ACTIVE_LOW>;
-		los-gpios        = <&sgpio_in2 15 1 GPIO_ACTIVE_HIGH>;
-		mod-def0-gpios   = <&sgpio_in2 15 2 GPIO_ACTIVE_LOW>;
-		tx-fault-gpios   = <&sgpio_in2 16 0 GPIO_ACTIVE_HIGH>;
+		los-gpios = <&sgpio_in2 15 1 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&sgpio_in2 15 2 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios = <&sgpio_in2 16 0 GPIO_ACTIVE_HIGH>;
 	};
 	sfp_eth49: sfp-eth49 {
-		compatible       = "sff,sfp";
-		i2c-bus          = <&i2c_sfp6>;
+		compatible = "sff,sfp";
+		i2c-bus = <&i2c_sfp6>;
 		tx-disable-gpios = <&sgpio_out2 16 1 GPIO_ACTIVE_LOW>;
-		los-gpios        = <&sgpio_in2 16 1 GPIO_ACTIVE_HIGH>;
-		mod-def0-gpios   = <&sgpio_in2 16 2 GPIO_ACTIVE_LOW>;
-		tx-fault-gpios   = <&sgpio_in2 17 0 GPIO_ACTIVE_HIGH>;
+		los-gpios = <&sgpio_in2 16 1 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&sgpio_in2 16 2 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios = <&sgpio_in2 17 0 GPIO_ACTIVE_HIGH>;
 	};
 	sfp_eth50: sfp-eth50 {
-		compatible       = "sff,sfp";
-		i2c-bus          = <&i2c_sfp7>;
+		compatible = "sff,sfp";
+		i2c-bus = <&i2c_sfp7>;
 		tx-disable-gpios = <&sgpio_out2 17 1 GPIO_ACTIVE_LOW>;
-		los-gpios        = <&sgpio_in2 17 1 GPIO_ACTIVE_HIGH>;
-		mod-def0-gpios   = <&sgpio_in2 17 2 GPIO_ACTIVE_LOW>;
-		tx-fault-gpios   = <&sgpio_in2 18 0 GPIO_ACTIVE_HIGH>;
+		los-gpios = <&sgpio_in2 17 1 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&sgpio_in2 17 2 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios = <&sgpio_in2 18 0 GPIO_ACTIVE_HIGH>;
 	};
 	sfp_eth51: sfp-eth51 {
-		compatible       = "sff,sfp";
-		i2c-bus          = <&i2c_sfp8>;
+		compatible = "sff,sfp";
+		i2c-bus = <&i2c_sfp8>;
 		tx-disable-gpios = <&sgpio_out2 18 1 GPIO_ACTIVE_LOW>;
-		los-gpios        = <&sgpio_in2 18 1 GPIO_ACTIVE_HIGH>;
-		mod-def0-gpios   = <&sgpio_in2 18 2 GPIO_ACTIVE_LOW>;
-		tx-fault-gpios   = <&sgpio_in2 19 0 GPIO_ACTIVE_HIGH>;
+		los-gpios = <&sgpio_in2 18 1 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&sgpio_in2 18 2 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios = <&sgpio_in2 19 0 GPIO_ACTIVE_HIGH>;
 	};
 	sfp_eth52: sfp-eth52 {
-		compatible       = "sff,sfp";
-		i2c-bus          = <&i2c_sfp9>;
+		compatible = "sff,sfp";
+		i2c-bus = <&i2c_sfp9>;
 		tx-disable-gpios = <&sgpio_out2 19 1 GPIO_ACTIVE_LOW>;
-		los-gpios        = <&sgpio_in2 19 1 GPIO_ACTIVE_HIGH>;
-		mod-def0-gpios   = <&sgpio_in2 19 2 GPIO_ACTIVE_LOW>;
-		tx-fault-gpios   = <&sgpio_in2 20 0 GPIO_ACTIVE_HIGH>;
+		los-gpios = <&sgpio_in2 19 1 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&sgpio_in2 19 2 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios = <&sgpio_in2 20 0 GPIO_ACTIVE_HIGH>;
 	};
 	sfp_eth53: sfp-eth53 {
-		compatible       = "sff,sfp";
-		i2c-bus          = <&i2c_sfp10>;
+		compatible = "sff,sfp";
+		i2c-bus = <&i2c_sfp10>;
 		tx-disable-gpios = <&sgpio_out2 20 1 GPIO_ACTIVE_LOW>;
-		los-gpios        = <&sgpio_in2 20 1 GPIO_ACTIVE_HIGH>;
-		mod-def0-gpios   = <&sgpio_in2 20 2 GPIO_ACTIVE_LOW>;
-		tx-fault-gpios   = <&sgpio_in2 21 0 GPIO_ACTIVE_HIGH>;
+		los-gpios = <&sgpio_in2 20 1 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&sgpio_in2 20 2 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios = <&sgpio_in2 21 0 GPIO_ACTIVE_HIGH>;
 	};
 	sfp_eth54: sfp-eth54 {
-		compatible       = "sff,sfp";
-		i2c-bus          = <&i2c_sfp11>;
+		compatible = "sff,sfp";
+		i2c-bus = <&i2c_sfp11>;
 		tx-disable-gpios = <&sgpio_out2 21 1 GPIO_ACTIVE_LOW>;
-		los-gpios        = <&sgpio_in2 21 1 GPIO_ACTIVE_HIGH>;
-		mod-def0-gpios   = <&sgpio_in2 21 2 GPIO_ACTIVE_LOW>;
-		tx-fault-gpios   = <&sgpio_in2 22 0 GPIO_ACTIVE_HIGH>;
+		los-gpios = <&sgpio_in2 21 1 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&sgpio_in2 21 2 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios = <&sgpio_in2 22 0 GPIO_ACTIVE_HIGH>;
 	};
 	sfp_eth55: sfp-eth55 {
-		compatible       = "sff,sfp";
-		i2c-bus          = <&i2c_sfp12>;
+		compatible = "sff,sfp";
+		i2c-bus = <&i2c_sfp12>;
 		tx-disable-gpios = <&sgpio_out2 22 1 GPIO_ACTIVE_LOW>;
-		los-gpios        = <&sgpio_in2 22 1 GPIO_ACTIVE_HIGH>;
-		mod-def0-gpios   = <&sgpio_in2 22 2 GPIO_ACTIVE_LOW>;
-		tx-fault-gpios   = <&sgpio_in2 23 0 GPIO_ACTIVE_HIGH>;
+		los-gpios = <&sgpio_in2 22 1 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&sgpio_in2 22 2 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios = <&sgpio_in2 23 0 GPIO_ACTIVE_HIGH>;
 	};
 	sfp_eth56: sfp-eth56 {
-		compatible       = "sff,sfp";
-		i2c-bus          = <&i2c_sfp13>;
+		compatible = "sff,sfp";
+		i2c-bus = <&i2c_sfp13>;
 		tx-disable-gpios = <&sgpio_out2 23 1 GPIO_ACTIVE_LOW>;
-		los-gpios        = <&sgpio_in2 23 1 GPIO_ACTIVE_HIGH>;
-		mod-def0-gpios   = <&sgpio_in2 23 2 GPIO_ACTIVE_LOW>;
-		tx-fault-gpios   = <&sgpio_in2 24 0 GPIO_ACTIVE_HIGH>;
+		los-gpios = <&sgpio_in2 23 1 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&sgpio_in2 23 2 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios = <&sgpio_in2 24 0 GPIO_ACTIVE_HIGH>;
 	};
 	sfp_eth57: sfp-eth57 {
-		compatible       = "sff,sfp";
-		i2c-bus          = <&i2c_sfp14>;
+		compatible = "sff,sfp";
+		i2c-bus = <&i2c_sfp14>;
 		tx-disable-gpios = <&sgpio_out2 24 1 GPIO_ACTIVE_LOW>;
-		los-gpios        = <&sgpio_in2 24 1 GPIO_ACTIVE_HIGH>;
-		mod-def0-gpios   = <&sgpio_in2 24 2 GPIO_ACTIVE_LOW>;
-		tx-fault-gpios   = <&sgpio_in2 25 0 GPIO_ACTIVE_HIGH>;
+		los-gpios = <&sgpio_in2 24 1 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&sgpio_in2 24 2 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios = <&sgpio_in2 25 0 GPIO_ACTIVE_HIGH>;
 	};
 	sfp_eth58: sfp-eth58 {
-		compatible       = "sff,sfp";
-		i2c-bus          = <&i2c_sfp15>;
+		compatible = "sff,sfp";
+		i2c-bus = <&i2c_sfp15>;
 		tx-disable-gpios = <&sgpio_out2 25 1 GPIO_ACTIVE_LOW>;
-		los-gpios        = <&sgpio_in2 25 1 GPIO_ACTIVE_HIGH>;
-		mod-def0-gpios   = <&sgpio_in2 25 2 GPIO_ACTIVE_LOW>;
-		tx-fault-gpios   = <&sgpio_in2 26 0 GPIO_ACTIVE_HIGH>;
+		los-gpios = <&sgpio_in2 25 1 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&sgpio_in2 25 2 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios = <&sgpio_in2 26 0 GPIO_ACTIVE_HIGH>;
 	};
 	sfp_eth59: sfp-eth59 {
-		compatible       = "sff,sfp";
-		i2c-bus          = <&i2c_sfp16>;
+		compatible = "sff,sfp";
+		i2c-bus = <&i2c_sfp16>;
 		tx-disable-gpios = <&sgpio_out2 26 1 GPIO_ACTIVE_LOW>;
-		los-gpios        = <&sgpio_in2 26 1 GPIO_ACTIVE_HIGH>;
-		mod-def0-gpios   = <&sgpio_in2 26 2 GPIO_ACTIVE_LOW>;
-		tx-fault-gpios   = <&sgpio_in2 27 0 GPIO_ACTIVE_HIGH>;
+		los-gpios = <&sgpio_in2 26 1 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&sgpio_in2 26 2 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios = <&sgpio_in2 27 0 GPIO_ACTIVE_HIGH>;
 	};
 	sfp_eth60: sfp-eth60 {
-		compatible       = "sff,sfp";
-		i2c-bus          = <&i2c_sfp17>;
+		compatible = "sff,sfp";
+		i2c-bus = <&i2c_sfp17>;
 		tx-disable-gpios = <&sgpio_out2 27 1 GPIO_ACTIVE_LOW>;
-		los-gpios        = <&sgpio_in2 27 1 GPIO_ACTIVE_HIGH>;
-		mod-def0-gpios   = <&sgpio_in2 27 2 GPIO_ACTIVE_LOW>;
-		tx-fault-gpios   = <&sgpio_in2 28 0 GPIO_ACTIVE_HIGH>;
+		los-gpios = <&sgpio_in2 27 1 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&sgpio_in2 27 2 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios = <&sgpio_in2 28 0 GPIO_ACTIVE_HIGH>;
 	};
 	sfp_eth61: sfp-eth61 {
-		compatible       = "sff,sfp";
-		i2c-bus          = <&i2c_sfp18>;
+		compatible = "sff,sfp";
+		i2c-bus = <&i2c_sfp18>;
 		tx-disable-gpios = <&sgpio_out2 28 1 GPIO_ACTIVE_LOW>;
-		los-gpios        = <&sgpio_in2 28 1 GPIO_ACTIVE_HIGH>;
-		mod-def0-gpios   = <&sgpio_in2 28 2 GPIO_ACTIVE_LOW>;
-		tx-fault-gpios   = <&sgpio_in2 29 0 GPIO_ACTIVE_HIGH>;
+		los-gpios = <&sgpio_in2 28 1 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&sgpio_in2 28 2 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios = <&sgpio_in2 29 0 GPIO_ACTIVE_HIGH>;
 	};
 	sfp_eth62: sfp-eth62 {
-		compatible       = "sff,sfp";
-		i2c-bus          = <&i2c_sfp19>;
+		compatible = "sff,sfp";
+		i2c-bus = <&i2c_sfp19>;
 		tx-disable-gpios = <&sgpio_out2 29 1 GPIO_ACTIVE_LOW>;
-		los-gpios        = <&sgpio_in2 29 1 GPIO_ACTIVE_HIGH>;
-		mod-def0-gpios   = <&sgpio_in2 29 2 GPIO_ACTIVE_LOW>;
-		tx-fault-gpios   = <&sgpio_in2 30 0 GPIO_ACTIVE_HIGH>;
+		los-gpios = <&sgpio_in2 29 1 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&sgpio_in2 29 2 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios = <&sgpio_in2 30 0 GPIO_ACTIVE_HIGH>;
 	};
 	sfp_eth63: sfp-eth63 {
-		compatible       = "sff,sfp";
-		i2c-bus          = <&i2c_sfp20>;
+		compatible = "sff,sfp";
+		i2c-bus = <&i2c_sfp20>;
 		tx-disable-gpios = <&sgpio_out2 30 1 GPIO_ACTIVE_LOW>;
-		los-gpios        = <&sgpio_in2 30 1 GPIO_ACTIVE_HIGH>;
-		mod-def0-gpios   = <&sgpio_in2 30 2 GPIO_ACTIVE_LOW>;
-		tx-fault-gpios   = <&sgpio_in2 31 0 GPIO_ACTIVE_HIGH>;
+		los-gpios = <&sgpio_in2 30 1 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&sgpio_in2 30 2 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios = <&sgpio_in2 31 0 GPIO_ACTIVE_HIGH>;
 	};
 };
 
diff --git a/arch/arm64/boot/dts/microchip/sparx5_pcb135_board.dtsi b/arch/arm64/boot/dts/microchip/sparx5_pcb135_board.dtsi
index ef96e6d8c6b3..ec90bda7ed6a 100644
--- a/arch/arm64/boot/dts/microchip/sparx5_pcb135_board.dtsi
+++ b/arch/arm64/boot/dts/microchip/sparx5_pcb135_board.dtsi
@@ -89,7 +89,7 @@
 
 &spi0 {
 	status = "okay";
-	spi-flash@0 {
+	flash@0 {
 		compatible = "jedec,spi-nor";
 		spi-max-frequency = <8000000>;
 		reg = <0>;
@@ -104,7 +104,7 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 		reg = <0>; /* CS0 */
-		spi-flash@9 {
+		flash@9 {
 			compatible = "jedec,spi-nor";
 			spi-max-frequency = <8000000>;
 			reg = <0x9>; /* SPI */
@@ -170,40 +170,40 @@
 
 &axi {
 	sfp_eth60: sfp-eth60 {
-		compatible	   = "sff,sfp";
-		i2c-bus            = <&i2c_sfp1>;
-		tx-disable-gpios   = <&sgpio_out2 28 0 GPIO_ACTIVE_LOW>;
+		compatible	 = "sff,sfp";
+		i2c-bus = <&i2c_sfp1>;
+		tx-disable-gpios = <&sgpio_out2 28 0 GPIO_ACTIVE_LOW>;
 		rate-select0-gpios = <&sgpio_out2 28 1 GPIO_ACTIVE_HIGH>;
-		los-gpios          = <&sgpio_in2 28 0 GPIO_ACTIVE_HIGH>;
-		mod-def0-gpios     = <&sgpio_in2 28 1 GPIO_ACTIVE_LOW>;
-		tx-fault-gpios     = <&sgpio_in2 28 2 GPIO_ACTIVE_HIGH>;
+		los-gpios = <&sgpio_in2 28 0 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&sgpio_in2 28 1 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios = <&sgpio_in2 28 2 GPIO_ACTIVE_HIGH>;
 	};
 	sfp_eth61: sfp-eth61 {
-		compatible         = "sff,sfp";
-		i2c-bus            = <&i2c_sfp2>;
-		tx-disable-gpios   = <&sgpio_out2 29 0 GPIO_ACTIVE_LOW>;
+		compatible = "sff,sfp";
+		i2c-bus = <&i2c_sfp2>;
+		tx-disable-gpios = <&sgpio_out2 29 0 GPIO_ACTIVE_LOW>;
 		rate-select0-gpios = <&sgpio_out2 29 1 GPIO_ACTIVE_HIGH>;
-		los-gpios          = <&sgpio_in2 29 0 GPIO_ACTIVE_HIGH>;
-		mod-def0-gpios     = <&sgpio_in2 29 1 GPIO_ACTIVE_LOW>;
-		tx-fault-gpios     = <&sgpio_in2 29 2 GPIO_ACTIVE_HIGH>;
+		los-gpios = <&sgpio_in2 29 0 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&sgpio_in2 29 1 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios = <&sgpio_in2 29 2 GPIO_ACTIVE_HIGH>;
 	};
 	sfp_eth62: sfp-eth62 {
-		compatible         = "sff,sfp";
-		i2c-bus            = <&i2c_sfp3>;
-		tx-disable-gpios   = <&sgpio_out2 30 0 GPIO_ACTIVE_LOW>;
+		compatible = "sff,sfp";
+		i2c-bus = <&i2c_sfp3>;
+		tx-disable-gpios = <&sgpio_out2 30 0 GPIO_ACTIVE_LOW>;
 		rate-select0-gpios = <&sgpio_out2 30 1 GPIO_ACTIVE_HIGH>;
-		los-gpios          = <&sgpio_in2 30 0 GPIO_ACTIVE_HIGH>;
-		mod-def0-gpios     = <&sgpio_in2 30 1 GPIO_ACTIVE_LOW>;
-		tx-fault-gpios     = <&sgpio_in2 30 2 GPIO_ACTIVE_HIGH>;
+		los-gpios = <&sgpio_in2 30 0 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&sgpio_in2 30 1 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios = <&sgpio_in2 30 2 GPIO_ACTIVE_HIGH>;
 	};
 	sfp_eth63: sfp-eth63 {
-		compatible         = "sff,sfp";
-		i2c-bus            = <&i2c_sfp4>;
-		tx-disable-gpios   = <&sgpio_out2 31 0 GPIO_ACTIVE_LOW>;
+		compatible = "sff,sfp";
+		i2c-bus = <&i2c_sfp4>;
+		tx-disable-gpios = <&sgpio_out2 31 0 GPIO_ACTIVE_LOW>;
 		rate-select0-gpios = <&sgpio_out2 31 1 GPIO_ACTIVE_HIGH>;
-		los-gpios          = <&sgpio_in2 31 0 GPIO_ACTIVE_HIGH>;
-		mod-def0-gpios     = <&sgpio_in2 31 1 GPIO_ACTIVE_LOW>;
-		tx-fault-gpios     = <&sgpio_in2 31 2 GPIO_ACTIVE_HIGH>;
+		los-gpios = <&sgpio_in2 31 0 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios = <&sgpio_in2 31 1 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios = <&sgpio_in2 31 2 GPIO_ACTIVE_HIGH>;
 	};
 };
 
diff --git a/arch/arm64/boot/dts/nuvoton/Makefile b/arch/arm64/boot/dts/nuvoton/Makefile
new file mode 100644
index 000000000000..a99dab90472a
--- /dev/null
+++ b/arch/arm64/boot/dts/nuvoton/Makefile
@@ -0,0 +1,2 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_NPCM) += nuvoton-npcm845-evb.dtb
diff --git a/arch/arm64/boot/dts/nuvoton/nuvoton-common-npcm8xx.dtsi b/arch/arm64/boot/dts/nuvoton/nuvoton-common-npcm8xx.dtsi
new file mode 100644
index 000000000000..aa7aac8c3774
--- /dev/null
+++ b/arch/arm64/boot/dts/nuvoton/nuvoton-common-npcm8xx.dtsi
@@ -0,0 +1,170 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (c) 2021 Nuvoton Technology tomer.maimon@nuvoton.com
+
+#include <dt-bindings/clock/nuvoton,npcm845-clk.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	#address-cells = <2>;
+	#size-cells = <2>;
+	interrupt-parent = <&gic>;
+
+	soc {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		compatible = "simple-bus";
+		interrupt-parent = <&gic>;
+		ranges;
+
+		gcr: system-controller@f0800000 {
+			compatible = "nuvoton,npcm845-gcr", "syscon";
+			reg = <0x0 0xf0800000 0x0 0x1000>;
+		};
+
+		gic: interrupt-controller@dfff9000 {
+			compatible = "arm,gic-400";
+			reg = <0x0 0xdfff9000 0x0 0x1000>,
+			      <0x0 0xdfffa000 0x0 0x2000>,
+			      <0x0 0xdfffc000 0x0 0x2000>,
+			      <0x0 0xdfffe000 0x0 0x2000>;
+			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+			#interrupt-cells = <3>;
+			interrupt-controller;
+			#address-cells = <0>;
+			ppi-partitions {
+				ppi_cluster0: interrupt-partition-0 {
+					affinity = <&cpu0 &cpu1 &cpu2 &cpu3>;
+				};
+			};
+		};
+	};
+
+	ahb {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		compatible = "simple-bus";
+		interrupt-parent = <&gic>;
+		ranges;
+
+		rstc: reset-controller@f0801000 {
+			compatible = "nuvoton,npcm845-reset";
+			reg = <0x0 0xf0801000 0x0 0x78>;
+			#reset-cells = <2>;
+			nuvoton,sysgcr = <&gcr>;
+		};
+
+		clk: clock-controller@f0801000 {
+			compatible = "nuvoton,npcm845-clk";
+			#clock-cells = <1>;
+			reg = <0x0 0xf0801000 0x0 0x1000>;
+		};
+
+		apb {
+			#address-cells = <1>;
+			#size-cells = <1>;
+			compatible = "simple-bus";
+			interrupt-parent = <&gic>;
+			ranges = <0x0 0x0 0xf0000000 0x00300000>,
+				<0xfff00000 0x0 0xfff00000 0x00016000>;
+
+			timer0: timer@8000 {
+				compatible = "nuvoton,npcm845-timer";
+				interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x8000 0x1C>;
+				clocks = <&clk NPCM8XX_CLK_REFCLK>;
+				clock-names = "refclk";
+			};
+
+			serial0: serial@0 {
+				compatible = "nuvoton,npcm845-uart", "nuvoton,npcm750-uart";
+				reg = <0x0 0x1000>;
+				clocks = <&clk NPCM8XX_CLK_UART>;
+				interrupts = <GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>;
+				reg-shift = <2>;
+				status = "disabled";
+			};
+
+			serial1: serial@1000 {
+				compatible = "nuvoton,npcm845-uart", "nuvoton,npcm750-uart";
+				reg = <0x1000 0x1000>;
+				clocks = <&clk NPCM8XX_CLK_UART>;
+				interrupts = <GIC_SPI 193 IRQ_TYPE_LEVEL_HIGH>;
+				reg-shift = <2>;
+				status = "disabled";
+			};
+
+			serial2: serial@2000 {
+				compatible = "nuvoton,npcm845-uart", "nuvoton,npcm750-uart";
+				reg = <0x2000 0x1000>;
+				clocks = <&clk NPCM8XX_CLK_UART>;
+				interrupts = <GIC_SPI 194 IRQ_TYPE_LEVEL_HIGH>;
+				reg-shift = <2>;
+				status = "disabled";
+			};
+
+			serial3: serial@3000 {
+				compatible = "nuvoton,npcm845-uart", "nuvoton,npcm750-uart";
+				reg = <0x3000 0x1000>;
+				clocks = <&clk NPCM8XX_CLK_UART>;
+				interrupts = <GIC_SPI 195 IRQ_TYPE_LEVEL_HIGH>;
+				reg-shift = <2>;
+				status = "disabled";
+			};
+
+			serial4: serial@4000 {
+				compatible = "nuvoton,npcm845-uart", "nuvoton,npcm750-uart";
+				reg = <0x4000 0x1000>;
+				clocks = <&clk NPCM8XX_CLK_UART>;
+				interrupts = <GIC_SPI 196 IRQ_TYPE_LEVEL_HIGH>;
+				reg-shift = <2>;
+				status = "disabled";
+			};
+
+			serial5: serial@5000 {
+				compatible = "nuvoton,npcm845-uart", "nuvoton,npcm750-uart";
+				reg = <0x5000 0x1000>;
+				clocks = <&clk NPCM8XX_CLK_UART>;
+				interrupts = <GIC_SPI 197 IRQ_TYPE_LEVEL_HIGH>;
+				reg-shift = <2>;
+				status = "disabled";
+			};
+
+			serial6: serial@6000 {
+				compatible = "nuvoton,npcm845-uart", "nuvoton,npcm750-uart";
+				reg = <0x6000 0x1000>;
+				clocks = <&clk NPCM8XX_CLK_UART>;
+				interrupts = <GIC_SPI 198 IRQ_TYPE_LEVEL_HIGH>;
+				reg-shift = <2>;
+				status = "disabled";
+			};
+
+			watchdog0: watchdog@801c {
+				compatible = "nuvoton,npcm845-wdt", "nuvoton,npcm750-wdt";
+				interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x801c 0x4>;
+				status = "disabled";
+				clocks = <&clk NPCM8XX_CLK_REFCLK>;
+				syscon = <&gcr>;
+			};
+
+			watchdog1: watchdog@901c {
+				compatible = "nuvoton,npcm845-wdt", "nuvoton,npcm750-wdt";
+				interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x901c 0x4>;
+				status = "disabled";
+				clocks = <&clk NPCM8XX_CLK_REFCLK>;
+				syscon = <&gcr>;
+			};
+
+			watchdog2: watchdog@a01c {
+				compatible = "nuvoton,npcm845-wdt", "nuvoton,npcm750-wdt";
+				interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0xa01c 0x4>;
+				status = "disabled";
+				clocks = <&clk NPCM8XX_CLK_REFCLK>;
+				syscon = <&gcr>;
+			};
+		};
+	};
+};
diff --git a/arch/arm64/boot/dts/nuvoton/nuvoton-npcm845-evb.dts b/arch/arm64/boot/dts/nuvoton/nuvoton-npcm845-evb.dts
new file mode 100644
index 000000000000..a5ab2bc0f835
--- /dev/null
+++ b/arch/arm64/boot/dts/nuvoton/nuvoton-npcm845-evb.dts
@@ -0,0 +1,30 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (c) 2021 Nuvoton Technology tomer.maimon@nuvoton.com
+
+/dts-v1/;
+#include "nuvoton-npcm845.dtsi"
+
+/ {
+	model = "Nuvoton npcm845 Development Board (Device Tree)";
+	compatible = "nuvoton,npcm845-evb", "nuvoton,npcm845";
+
+	aliases {
+		serial0 = &serial0;
+	};
+
+	chosen {
+		stdout-path = &serial0;
+	};
+
+	memory {
+		reg = <0x0 0x0 0x0 0x40000000>;
+	};
+};
+
+&serial0 {
+	status = "okay";
+};
+
+&watchdog1 {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/nuvoton/nuvoton-npcm845.dtsi b/arch/arm64/boot/dts/nuvoton/nuvoton-npcm845.dtsi
new file mode 100644
index 000000000000..12118b75c0e6
--- /dev/null
+++ b/arch/arm64/boot/dts/nuvoton/nuvoton-npcm845.dtsi
@@ -0,0 +1,76 @@
+// SPDX-License-Identifier: GPL-2.0
+// Copyright (c) 2021 Nuvoton Technology tomer.maimon@nuvoton.com
+
+#include "nuvoton-common-npcm8xx.dtsi"
+
+/ {
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	cpus {
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a35";
+			clocks = <&clk NPCM8XX_CLK_CPU>;
+			reg = <0x0 0x0>;
+			next-level-cache = <&l2>;
+			enable-method = "psci";
+		};
+
+		cpu1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a35";
+			clocks = <&clk NPCM8XX_CLK_CPU>;
+			reg = <0x0 0x1>;
+			next-level-cache = <&l2>;
+			enable-method = "psci";
+		};
+
+		cpu2: cpu@2 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a35";
+			clocks = <&clk NPCM8XX_CLK_CPU>;
+			reg = <0x0 0x2>;
+			next-level-cache = <&l2>;
+			enable-method = "psci";
+		};
+
+		cpu3: cpu@3 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a35";
+			clocks = <&clk NPCM8XX_CLK_CPU>;
+			reg = <0x0 0x3>;
+			next-level-cache = <&l2>;
+			enable-method = "psci";
+		};
+
+		l2: l2-cache {
+			compatible = "cache";
+		};
+	};
+
+	arm-pmu {
+		compatible = "arm,cortex-a35-pmu";
+		interrupts = <GIC_SPI 242 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 243 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 244 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 245 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>;
+	};
+
+	psci {
+		compatible      = "arm,psci-1.0";
+		method          = "smc";
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+	};
+};
diff --git a/arch/arm64/boot/dts/nvidia/Makefile b/arch/arm64/boot/dts/nvidia/Makefile
index c80f7dc2935e..bc34c9d8846a 100644
--- a/arch/arm64/boot/dts/nvidia/Makefile
+++ b/arch/arm64/boot/dts/nvidia/Makefile
@@ -1,4 +1,15 @@
 # SPDX-License-Identifier: GPL-2.0
+
+# Enables support for device-tree overlays
+DTC_FLAGS_tegra210-p2371-2180 := -@
+DTC_FLAGS_tegra210-p3450-0000 := -@
+DTC_FLAGS_tegra186-p2771-0000 := -@
+DTC_FLAGS_tegra186-p3509-0000+p3636-0001 := -@
+DTC_FLAGS_tegra194-p2972-0000 := -@
+DTC_FLAGS_tegra194-p3509-0000+p3668-0000 := -@
+DTC_FLAGS_tegra194-p3509-0000+p3668-0001 := -@
+DTC_FLAGS_tegra234-p3737-0000+p3701-0000 := -@
+
 dtb-$(CONFIG_ARCH_TEGRA_132_SOC) += tegra132-norrin.dtb
 dtb-$(CONFIG_ARCH_TEGRA_210_SOC) += tegra210-p2371-0000.dtb
 dtb-$(CONFIG_ARCH_TEGRA_210_SOC) += tegra210-p2371-2180.dtb
@@ -12,3 +23,4 @@ dtb-$(CONFIG_ARCH_TEGRA_194_SOC) += tegra194-p2972-0000.dtb
 dtb-$(CONFIG_ARCH_TEGRA_194_SOC) += tegra194-p3509-0000+p3668-0000.dtb
 dtb-$(CONFIG_ARCH_TEGRA_194_SOC) += tegra194-p3509-0000+p3668-0001.dtb
 dtb-$(CONFIG_ARCH_TEGRA_234_SOC) += tegra234-sim-vdk.dtb
+dtb-$(CONFIG_ARCH_TEGRA_234_SOC) += tegra234-p3737-0000+p3701-0000.dtb
diff --git a/arch/arm64/boot/dts/nvidia/tegra132-norrin.dts b/arch/arm64/boot/dts/nvidia/tegra132-norrin.dts
index 8a51751526ee..d461da0b8049 100644
--- a/arch/arm64/boot/dts/nvidia/tegra132-norrin.dts
+++ b/arch/arm64/boot/dts/nvidia/tegra132-norrin.dts
@@ -564,7 +564,7 @@
 			pinctrl-names = "default";
 			pinctrl-0 = <&as3722_default>;
 
-			as3722_default: pinmux@0 {
+			as3722_default: pinmux {
 				gpio0 {
 					pins = "gpio0";
 					function = "gpio";
@@ -770,7 +770,7 @@
 
 				google,remote-bus = <0>;
 
-				charger: bq24735 {
+				charger: bq24735@9 {
 					compatible = "ti,bq24735";
 					reg = <0x9>;
 					interrupt-parent = <&gpio>;
@@ -781,7 +781,7 @@
 							GPIO_ACTIVE_HIGH>;
 				};
 
-				battery: smart-battery {
+				battery: smart-battery@b {
 					compatible = "sbs,sbs-battery";
 					reg = <0xb>;
 					sbs,i2c-retry-count = <2>;
@@ -885,14 +885,12 @@
 	pmc@7000e400 {
 		nvidia,invert-interrupt;
 		nvidia,suspend-mode = <0>;
-		#wake-cells = <3>;
 		nvidia,cpu-pwr-good-time = <500>;
 		nvidia,cpu-pwr-off-time = <300>;
 		nvidia,core-pwr-good-time = <641 3845>;
 		nvidia,core-pwr-off-time = <61036>;
 		nvidia,core-power-req-active-high;
 		nvidia,sys-clock-req-active-high;
-		nvidia,reset-gpio = <&gpio TEGRA_GPIO(I, 5) GPIO_ACTIVE_LOW>;
 	};
 
 	usb@70090000 {
@@ -1023,7 +1021,7 @@
 		default-brightness-level = <6>;
 	};
 
-	clk32k_in: clock@0 {
+	clk32k_in: clock-32k {
 		compatible = "fixed-clock";
 		clock-frequency = <32768>;
 		#clock-cells = <0>;
@@ -1032,7 +1030,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		lid {
+		switch-lid {
 			label = "Lid";
 			gpios = <&gpio TEGRA_GPIO(R, 4) GPIO_ACTIVE_LOW>;
 			linux,input-type = <5>;
@@ -1041,7 +1039,7 @@
 			wakeup-source;
 		};
 
-		power {
+		key-power {
 			label = "Power";
 			gpios = <&gpio TEGRA_GPIO(Q, 0) GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
@@ -1057,7 +1055,7 @@
 		ddc-i2c-bus = <&dpaux>;
 	};
 
-	vdd_mux: regulator@0 {
+	vdd_mux: regulator-vdd-mux {
 		compatible = "regulator-fixed";
 		regulator-name = "+VDD_MUX";
 		regulator-min-microvolt = <19000000>;
@@ -1066,7 +1064,7 @@
 		regulator-boot-on;
 	};
 
-	vdd_5v0_sys: regulator@1 {
+	vdd_5v0_sys: regulator-vdd-5v0-sys {
 		compatible = "regulator-fixed";
 		regulator-name = "+5V_SYS";
 		regulator-min-microvolt = <5000000>;
@@ -1076,7 +1074,7 @@
 		vin-supply = <&vdd_mux>;
 	};
 
-	vdd_3v3_sys: regulator@2 {
+	vdd_3v3_sys: regulator-vdd-3v3-sys {
 		compatible = "regulator-fixed";
 		regulator-name = "+3.3V_SYS";
 		regulator-min-microvolt = <3300000>;
@@ -1086,7 +1084,7 @@
 		vin-supply = <&vdd_mux>;
 	};
 
-	vdd_3v3_run: regulator@3 {
+	vdd_3v3_run: regulator-vdd-3v3-run {
 		compatible = "regulator-fixed";
 		regulator-name = "+3.3V_RUN";
 		regulator-min-microvolt = <3300000>;
@@ -1098,7 +1096,7 @@
 		vin-supply = <&vdd_3v3_sys>;
 	};
 
-	vdd_3v3_hdmi: regulator@4 {
+	vdd_3v3_hdmi: regulator-vdd-3v3-hdmi {
 		compatible = "regulator-fixed";
 		regulator-name = "+3.3V_AVDD_HDMI_AP_GATED";
 		regulator-min-microvolt = <3300000>;
@@ -1106,7 +1104,7 @@
 		vin-supply = <&vdd_3v3_run>;
 	};
 
-	vdd_led: regulator@5 {
+	vdd_led: regulator-vdd-led {
 		compatible = "regulator-fixed";
 		regulator-name = "+VDD_LED";
 		regulator-min-microvolt = <3300000>;
@@ -1116,7 +1114,7 @@
 		vin-supply = <&vdd_mux>;
 	};
 
-	vdd_usb1_vbus: regulator@6 {
+	vdd_usb1_vbus: regulator-vdd-usb1-vbus {
 		compatible = "regulator-fixed";
 		regulator-name = "+5V_USB_HS";
 		regulator-min-microvolt = <5000000>;
@@ -1127,7 +1125,7 @@
 		vin-supply = <&vdd_5v0_sys>;
 	};
 
-	vdd_usb3_vbus: regulator@7 {
+	vdd_usb3_vbus: regulator-vdd-usb3-vbus {
 		compatible = "regulator-fixed";
 		regulator-name = "+5V_USB_SS";
 		regulator-min-microvolt = <5000000>;
@@ -1138,7 +1136,7 @@
 		vin-supply = <&vdd_5v0_sys>;
 	};
 
-	vdd_3v3_panel: regulator@8 {
+	vdd_3v3_panel: regulator-vdd-3v3-panel {
 		compatible = "regulator-fixed";
 		regulator-name = "+3.3V_PANEL";
 		regulator-min-microvolt = <3300000>;
@@ -1148,7 +1146,7 @@
 		vin-supply = <&vdd_3v3_sys>;
 	};
 
-	vdd_hdmi_pll: regulator@9 {
+	vdd_hdmi_pll: regulator-vdd-hdmi-pll {
 		compatible = "regulator-fixed";
 		regulator-name = "+1.05V_RUN_AVDD_HDMI_PLL_AP_GATE";
 		regulator-min-microvolt = <1050000>;
@@ -1157,7 +1155,7 @@
 		vin-supply = <&vdd_1v05_run>;
 	};
 
-	vdd_5v0_hdmi: regulator@10 {
+	vdd_5v0_hdmi: regulator-vdd-5v0-hdmi {
 		compatible = "regulator-fixed";
 		regulator-name = "+5V_HDMI_CON";
 		regulator-min-microvolt = <5000000>;
@@ -1167,7 +1165,7 @@
 		vin-supply = <&vdd_5v0_sys>;
 	};
 
-	vdd_5v0_ts: regulator@11 {
+	vdd_5v0_ts: regulator-vdd-5v0-ts {
 		compatible = "regulator-fixed";
 		regulator-name = "+5V_VDD_TS";
 		regulator-min-microvolt = <5000000>;
@@ -1178,7 +1176,7 @@
 		enable-active-high;
 	};
 
-	vdd_3v3_lp0: regulator@12 {
+	vdd_3v3_lp0: regulator-vdd-3v3-lp0 {
 		compatible = "regulator-fixed";
 		regulator-name = "+3.3V_LP0";
 		regulator-min-microvolt = <3300000>;
diff --git a/arch/arm64/boot/dts/nvidia/tegra132-peripherals-opp.dtsi b/arch/arm64/boot/dts/nvidia/tegra132-peripherals-opp.dtsi
new file mode 100644
index 000000000000..66ffb7f8aaa7
--- /dev/null
+++ b/arch/arm64/boot/dts/nvidia/tegra132-peripherals-opp.dtsi
@@ -0,0 +1,426 @@
+// SPDX-License-Identifier: GPL-2.0
+
+/ {
+	/* EMC DVFS OPP table */
+	emc_icc_dvfs_opp_table: opp-table-dvfs0 {
+		compatible = "operating-points-v2";
+
+		opp-12750000-800 {
+			opp-microvolt = <800000 800000 1150000>;
+			opp-hz = /bits/ 64 <12750000>;
+			opp-supported-hw = <0x0003>;
+		};
+
+		opp-12750000-950 {
+			opp-microvolt = <950000 950000 1150000>;
+			opp-hz = /bits/ 64 <12750000>;
+			opp-supported-hw = <0x0008>;
+		};
+
+		opp-12750000-1050 {
+			opp-microvolt = <1050000 1050000 1150000>;
+			opp-hz = /bits/ 64 <12750000>;
+			opp-supported-hw = <0x0010>;
+		};
+
+		opp-12750000-1110 {
+			opp-microvolt = <1110000 1110000 1150000>;
+			opp-hz = /bits/ 64 <12750000>;
+			opp-supported-hw = <0x0004>;
+		};
+
+		opp-20400000-800 {
+			opp-microvolt = <800000 800000 1150000>;
+			opp-hz = /bits/ 64 <20400000>;
+			opp-supported-hw = <0x0003>;
+		};
+
+		opp-20400000-950 {
+			opp-microvolt = <950000 950000 1150000>;
+			opp-hz = /bits/ 64 <20400000>;
+			opp-supported-hw = <0x0008>;
+		};
+
+		opp-20400000-1050 {
+			opp-microvolt = <1050000 1050000 1150000>;
+			opp-hz = /bits/ 64 <20400000>;
+			opp-supported-hw = <0x0010>;
+		};
+
+		opp-20400000-1110 {
+			opp-microvolt = <1110000 1110000 1150000>;
+			opp-hz = /bits/ 64 <20400000>;
+			opp-supported-hw = <0x0004>;
+		};
+
+		opp-40800000-800 {
+			opp-microvolt = <800000 800000 1150000>;
+			opp-hz = /bits/ 64 <40800000>;
+			opp-supported-hw = <0x0003>;
+		};
+
+		opp-40800000-950 {
+			opp-microvolt = <950000 950000 1150000>;
+			opp-hz = /bits/ 64 <40800000>;
+			opp-supported-hw = <0x0008>;
+		};
+
+		opp-40800000-1050 {
+			opp-microvolt = <1050000 1050000 1150000>;
+			opp-hz = /bits/ 64 <40800000>;
+			opp-supported-hw = <0x0010>;
+		};
+
+		opp-40800000-1110 {
+			opp-microvolt = <1110000 1110000 1150000>;
+			opp-hz = /bits/ 64 <40800000>;
+			opp-supported-hw = <0x0004>;
+		};
+
+		opp-68000000-800 {
+			opp-microvolt = <800000 800000 1150000>;
+			opp-hz = /bits/ 64 <68000000>;
+			opp-supported-hw = <0x0003>;
+		};
+
+		opp-68000000-950 {
+			opp-microvolt = <950000 950000 1150000>;
+			opp-hz = /bits/ 64 <68000000>;
+			opp-supported-hw = <0x0008>;
+		};
+
+		opp-68000000-1050 {
+			opp-microvolt = <1050000 1050000 1150000>;
+			opp-hz = /bits/ 64 <68000000>;
+			opp-supported-hw = <0x0010>;
+		};
+
+		opp-68000000-1110 {
+			opp-microvolt = <1110000 1110000 1150000>;
+			opp-hz = /bits/ 64 <68000000>;
+			opp-supported-hw = <0x0004>;
+		};
+
+		opp-102000000-800 {
+			opp-microvolt = <800000 800000 1150000>;
+			opp-hz = /bits/ 64 <102000000>;
+			opp-supported-hw = <0x0003>;
+		};
+
+		opp-102000000-950 {
+			opp-microvolt = <950000 950000 1150000>;
+			opp-hz = /bits/ 64 <102000000>;
+			opp-supported-hw = <0x0008>;
+		};
+
+		opp-102000000-1050 {
+			opp-microvolt = <1050000 1050000 1150000>;
+			opp-hz = /bits/ 64 <102000000>;
+			opp-supported-hw = <0x0010>;
+		};
+
+		opp-102000000-1110 {
+			opp-microvolt = <1110000 1110000 1150000>;
+			opp-hz = /bits/ 64 <102000000>;
+			opp-supported-hw = <0x0004>;
+		};
+
+		opp-204000000-800 {
+			opp-microvolt = <800000 800000 1150000>;
+			opp-hz = /bits/ 64 <204000000>;
+			opp-supported-hw = <0x0003>;
+			opp-suspend;
+		};
+
+		opp-204000000-950 {
+			opp-microvolt = <950000 950000 1150000>;
+			opp-hz = /bits/ 64 <204000000>;
+			opp-supported-hw = <0x0008>;
+			opp-suspend;
+		};
+
+		opp-204000000-1050 {
+			opp-microvolt = <1050000 1050000 1150000>;
+			opp-hz = /bits/ 64 <204000000>;
+			opp-supported-hw = <0x0010>;
+			opp-suspend;
+		};
+
+		opp-204000000-1110 {
+			opp-microvolt = <1110000 1110000 1150000>;
+			opp-hz = /bits/ 64 <204000000>;
+			opp-supported-hw = <0x0004>;
+			opp-suspend;
+		};
+
+		opp-264000000-800 {
+			opp-microvolt = <800000 800000 1150000>;
+			opp-hz = /bits/ 64 <264000000>;
+			opp-supported-hw = <0x0003>;
+		};
+
+		opp-264000000-950 {
+			opp-microvolt = <950000 950000 1150000>;
+			opp-hz = /bits/ 64 <264000000>;
+			opp-supported-hw = <0x0008>;
+		};
+
+		opp-264000000-1050 {
+			opp-microvolt = <1050000 1050000 1150000>;
+			opp-hz = /bits/ 64 <264000000>;
+			opp-supported-hw = <0x0010>;
+		};
+
+		opp-264000000-1110 {
+			opp-microvolt = <1110000 1110000 1150000>;
+			opp-hz = /bits/ 64 <264000000>;
+			opp-supported-hw = <0x0004>;
+		};
+
+		opp-300000000-850 {
+			opp-microvolt = <850000 850000 1150000>;
+			opp-hz = /bits/ 64 <300000000>;
+			opp-supported-hw = <0x0003>;
+		};
+
+		opp-300000000-950 {
+			opp-microvolt = <950000 950000 1150000>;
+			opp-hz = /bits/ 64 <300000000>;
+			opp-supported-hw = <0x0008>;
+		};
+
+		opp-300000000-1050 {
+			opp-microvolt = <1050000 1050000 1150000>;
+			opp-hz = /bits/ 64 <300000000>;
+			opp-supported-hw = <0x0010>;
+		};
+
+		opp-300000000-1110 {
+			opp-microvolt = <1110000 1110000 1150000>;
+			opp-hz = /bits/ 64 <300000000>;
+			opp-supported-hw = <0x0004>;
+		};
+
+		opp-348000000-850 {
+			opp-microvolt = <850000 850000 1150000>;
+			opp-hz = /bits/ 64 <348000000>;
+			opp-supported-hw = <0x0003>;
+		};
+
+		opp-348000000-950 {
+			opp-microvolt = <950000 950000 1150000>;
+			opp-hz = /bits/ 64 <348000000>;
+			opp-supported-hw = <0x0008>;
+		};
+
+		opp-348000000-1050 {
+			opp-microvolt = <1050000 1050000 1150000>;
+			opp-hz = /bits/ 64 <348000000>;
+			opp-supported-hw = <0x0010>;
+		};
+
+		opp-348000000-1110 {
+			opp-microvolt = <1110000 1110000 1150000>;
+			opp-hz = /bits/ 64 <348000000>;
+			opp-supported-hw = <0x0004>;
+		};
+
+		opp-396000000-950 {
+			opp-microvolt = <950000 950000 1150000>;
+			opp-hz = /bits/ 64 <396000000>;
+			opp-supported-hw = <0x0008>;
+		};
+
+		opp-396000000-1000 {
+			opp-microvolt = <1000000 1000000 1150000>;
+			opp-hz = /bits/ 64 <396000000>;
+			opp-supported-hw = <0x0003>;
+		};
+
+		opp-396000000-1050 {
+			opp-microvolt = <1050000 1050000 1150000>;
+			opp-hz = /bits/ 64 <396000000>;
+			opp-supported-hw = <0x0010>;
+		};
+
+		opp-396000000-1110 {
+			opp-microvolt = <1110000 1110000 1150000>;
+			opp-hz = /bits/ 64 <396000000>;
+			opp-supported-hw = <0x0004>;
+		};
+
+		opp-528000000-950 {
+			opp-microvolt = <950000 950000 1150000>;
+			opp-hz = /bits/ 64 <528000000>;
+			opp-supported-hw = <0x0008>;
+		};
+
+		opp-528000000-1000 {
+			opp-microvolt = <1000000 1000000 1150000>;
+			opp-hz = /bits/ 64 <528000000>;
+			opp-supported-hw = <0x0003>;
+		};
+
+		opp-528000000-1050 {
+			opp-microvolt = <1050000 1050000 1150000>;
+			opp-hz = /bits/ 64 <528000000>;
+			opp-supported-hw = <0x0010>;
+		};
+
+		opp-528000000-1110 {
+			opp-microvolt = <1110000 1110000 1150000>;
+			opp-hz = /bits/ 64 <528000000>;
+			opp-supported-hw = <0x0004>;
+		};
+
+		opp-600000000-950 {
+			opp-microvolt = <950000 950000 1150000>;
+			opp-hz = /bits/ 64 <600000000>;
+			opp-supported-hw = <0x0008>;
+		};
+
+		opp-600000000-1000 {
+			opp-microvolt = <1000000 1000000 1150000>;
+			opp-hz = /bits/ 64 <600000000>;
+			opp-supported-hw = <0x0003>;
+		};
+
+		opp-600000000-1050 {
+			opp-microvolt = <1050000 1050000 1150000>;
+			opp-hz = /bits/ 64 <600000000>;
+			opp-supported-hw = <0x0010>;
+		};
+
+		opp-600000000-1110 {
+			opp-microvolt = <1110000 1110000 1150000>;
+			opp-hz = /bits/ 64 <600000000>;
+			opp-supported-hw = <0x0004>;
+		};
+
+		opp-792000000-1000 {
+			opp-microvolt = <1000000 1000000 1150000>;
+			opp-hz = /bits/ 64 <792000000>;
+			opp-supported-hw = <0x000B>;
+		};
+
+		opp-792000000-1050 {
+			opp-microvolt = <1050000 1050000 1150000>;
+			opp-hz = /bits/ 64 <792000000>;
+			opp-supported-hw = <0x0010>;
+		};
+
+		opp-792000000-1110 {
+			opp-microvolt = <1110000 1110000 1150000>;
+			opp-hz = /bits/ 64 <792000000>;
+			opp-supported-hw = <0x0004>;
+		};
+
+		opp-924000000-1100 {
+			opp-microvolt = <1100000 1100000 1150000>;
+			opp-hz = /bits/ 64 <924000000>;
+			opp-supported-hw = <0x0013>;
+		};
+
+		opp-1200000000-1100 {
+			opp-microvolt = <1100000 1100000 1150000>;
+			opp-hz = /bits/ 64 <1200000000>;
+			opp-supported-hw = <0x0003>;
+		};
+	};
+
+	/* EMC bandwidth OPP table */
+	emc_bw_dfs_opp_table: opp-table-dvfs1 {
+		compatible = "operating-points-v2";
+
+		opp-12750000 {
+			opp-hz = /bits/ 64 <12750000>;
+			opp-supported-hw = <0x001F>;
+			opp-peak-kBps = <204000>;
+		};
+
+		opp-20400000 {
+			opp-hz = /bits/ 64 <20400000>;
+			opp-supported-hw = <0x001F>;
+			opp-peak-kBps = <326400>;
+		};
+
+		opp-40800000 {
+			opp-hz = /bits/ 64 <40800000>;
+			opp-supported-hw = <0x001F>;
+			opp-peak-kBps = <652800>;
+		};
+
+		opp-68000000 {
+			opp-hz = /bits/ 64 <68000000>;
+			opp-supported-hw = <0x001F>;
+			opp-peak-kBps = <1088000>;
+		};
+
+		opp-102000000 {
+			opp-hz = /bits/ 64 <102000000>;
+			opp-supported-hw = <0x001F>;
+			opp-peak-kBps = <1632000>;
+		};
+
+		opp-204000000 {
+			opp-hz = /bits/ 64 <204000000>;
+			opp-supported-hw = <0x001F>;
+			opp-peak-kBps = <3264000>;
+			opp-suspend;
+		};
+
+		opp-264000000 {
+			opp-hz = /bits/ 64 <264000000>;
+			opp-supported-hw = <0x001F>;
+			opp-peak-kBps = <4224000>;
+		};
+
+		opp-300000000 {
+			opp-hz = /bits/ 64 <300000000>;
+			opp-supported-hw = <0x001F>;
+			opp-peak-kBps = <4800000>;
+		};
+
+		opp-348000000 {
+			opp-hz = /bits/ 64 <348000000>;
+			opp-supported-hw = <0x001F>;
+			opp-peak-kBps = <5568000>;
+		};
+
+		opp-396000000 {
+			opp-hz = /bits/ 64 <396000000>;
+			opp-supported-hw = <0x001F>;
+			opp-peak-kBps = <6336000>;
+		};
+
+		opp-528000000 {
+			opp-hz = /bits/ 64 <528000000>;
+			opp-supported-hw = <0x001F>;
+			opp-peak-kBps = <8448000>;
+		};
+
+		opp-600000000 {
+			opp-hz = /bits/ 64 <600000000>;
+			opp-supported-hw = <0x001F>;
+			opp-peak-kBps = <9600000>;
+		};
+
+		opp-792000000 {
+			opp-hz = /bits/ 64 <792000000>;
+			opp-supported-hw = <0x001F>;
+			opp-peak-kBps = <12672000>;
+		};
+
+		opp-924000000 {
+			opp-hz = /bits/ 64 <924000000>;
+			opp-supported-hw = <0x0013>;
+			opp-peak-kBps = <14784000>;
+		};
+
+		opp-1200000000 {
+			opp-hz = /bits/ 64 <1200000000>;
+			opp-supported-hw = <0x0003>;
+			opp-peak-kBps = <19200000>;
+		};
+	};
+};
diff --git a/arch/arm64/boot/dts/nvidia/tegra132.dtsi b/arch/arm64/boot/dts/nvidia/tegra132.dtsi
index 63aa3129d8fc..3673f79adf1a 100644
--- a/arch/arm64/boot/dts/nvidia/tegra132.dtsi
+++ b/arch/arm64/boot/dts/nvidia/tegra132.dtsi
@@ -8,6 +8,8 @@
 #include <dt-bindings/thermal/tegra124-soctherm.h>
 #include <dt-bindings/soc/tegra-pmc.h>
 
+#include "tegra132-peripherals-opp.dtsi"
+
 / {
 	compatible = "nvidia,tegra132", "nvidia,tegra124";
 	interrupt-parent = <&lic>;
@@ -210,7 +212,7 @@
 	};
 
 	timer@60005000 {
-		compatible = "nvidia,tegra124-timer", "nvidia,tegra20-timer";
+		compatible = "nvidia,tegra124-timer", "nvidia,tegra30-timer";
 		reg = <0x0 0x60005000 0x0 0x400>;
 		interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
 			     <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>,
@@ -244,6 +246,10 @@
 		clock-names = "actmon", "emc";
 		resets = <&tegra_car 119>;
 		reset-names = "actmon";
+		operating-points-v2 = <&emc_bw_dfs_opp_table>;
+		interconnects = <&mc TEGRA124_MC_MPCORER &emc>;
+		interconnect-names = "cpu-read";
+		#cooling-cells = <2>;
 	};
 
 	gpio: gpio@6000d000 {
@@ -394,7 +400,7 @@
 	};
 
 	i2c@7000c000 {
-		compatible = "nvidia,tegra124-i2c", "nvidia,tegra114-i2c";
+		compatible = "nvidia,tegra124-i2c";
 		reg = <0x0 0x7000c000 0x0 0x100>;
 		interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
 		#address-cells = <1>;
@@ -409,7 +415,7 @@
 	};
 
 	i2c@7000c400 {
-		compatible = "nvidia,tegra124-i2c", "nvidia,tegra114-i2c";
+		compatible = "nvidia,tegra124-i2c";
 		reg = <0x0 0x7000c400 0x0 0x100>;
 		interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
 		#address-cells = <1>;
@@ -424,7 +430,7 @@
 	};
 
 	i2c@7000c500 {
-		compatible = "nvidia,tegra124-i2c", "nvidia,tegra114-i2c";
+		compatible = "nvidia,tegra124-i2c";
 		reg = <0x0 0x7000c500 0x0 0x100>;
 		interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>;
 		#address-cells = <1>;
@@ -439,7 +445,7 @@
 	};
 
 	i2c@7000c700 {
-		compatible = "nvidia,tegra124-i2c", "nvidia,tegra114-i2c";
+		compatible = "nvidia,tegra124-i2c";
 		reg = <0x0 0x7000c700 0x0 0x100>;
 		interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
 		#address-cells = <1>;
@@ -454,7 +460,7 @@
 	};
 
 	i2c@7000d000 {
-		compatible = "nvidia,tegra124-i2c", "nvidia,tegra114-i2c";
+		compatible = "nvidia,tegra124-i2c";
 		reg = <0x0 0x7000d000 0x0 0x100>;
 		interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>;
 		#address-cells = <1>;
@@ -469,7 +475,7 @@
 	};
 
 	i2c@7000d100 {
-		compatible = "nvidia,tegra124-i2c", "nvidia,tegra114-i2c";
+		compatible = "nvidia,tegra124-i2c";
 		reg = <0x0 0x7000d100 0x0 0x100>;
 		interrupts = <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>;
 		#address-cells = <1>;
@@ -607,15 +613,20 @@
 		interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
 
 		#iommu-cells = <1>;
+		#reset-cells = <1>;
+		#interconnect-cells = <1>;
 	};
 
 	emc: external-memory-controller@7001b000 {
-		compatible = "nvidia,tegra132-emc";
+		compatible = "nvidia,tegra132-emc", "nvidia,tegra124-emc";
 		reg = <0x0 0x7001b000 0x0 0x1000>;
 		clocks = <&tegra_car TEGRA124_CLK_EMC>;
 		clock-names = "emc";
 
 		nvidia,memory-controller = <&mc>;
+		operating-points-v2 = <&emc_icc_dvfs_opp_table>;
+
+		#interconnect-cells = <0>;
 	};
 
 	sata@70020000 {
@@ -624,10 +635,8 @@
 		      <0x0 0x70020000 0x0 0x7000>; /* SATA */
 		interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&tegra_car TEGRA124_CLK_SATA>,
-			 <&tegra_car TEGRA124_CLK_SATA_OOB>,
-			 <&tegra_car TEGRA124_CLK_CML1>,
-			 <&tegra_car TEGRA124_CLK_PLL_E>;
-		clock-names = "sata", "sata-oob", "cml1", "pll_e";
+			 <&tegra_car TEGRA124_CLK_SATA_OOB>;
+		clock-names = "sata", "sata-oob";
 		resets = <&tegra_car 124>,
 			 <&tegra_car 129>,
 			 <&tegra_car 123>;
@@ -665,8 +674,8 @@
 			 <&tegra_car TEGRA124_CLK_XUSB_HOST_SRC>,
 			 <&tegra_car TEGRA124_CLK_XUSB_FALCON_SRC>,
 			 <&tegra_car TEGRA124_CLK_XUSB_SS>,
-			 <&tegra_car TEGRA124_CLK_XUSB_SS_SRC>,
 			 <&tegra_car TEGRA124_CLK_XUSB_SS_DIV2>,
+			 <&tegra_car TEGRA124_CLK_XUSB_SS_SRC>,
 			 <&tegra_car TEGRA124_CLK_XUSB_HS_SRC>,
 			 <&tegra_car TEGRA124_CLK_XUSB_FS_SRC>,
 			 <&tegra_car TEGRA124_CLK_PLL_U_480M>,
@@ -674,7 +683,7 @@
 			 <&tegra_car TEGRA124_CLK_PLL_E>;
 		clock-names = "xusb_host", "xusb_host_src",
 			      "xusb_falcon_src", "xusb_ss",
-			      "xusb_ss_src", "xusb_ss_div2",
+			      "xusb_ss_div2", "xusb_ss_src",
 			      "xusb_hs_src", "xusb_fs_src",
 			      "pll_u_480m", "clk_m", "pll_e";
 		resets = <&tegra_car 89>, <&tegra_car 156>,
@@ -886,7 +895,7 @@
 	};
 
 	thermal-zones {
-		cpu {
+		cpu-thermal {
 			polling-delay-passive = <1000>;
 			polling-delay = <0>;
 
@@ -914,7 +923,8 @@
 				};
 			};
 		};
-		mem {
+
+		mem-thermal {
 			polling-delay-passive = <0>;
 			polling-delay = <0>;
 
@@ -941,7 +951,8 @@
 				 */
 			};
 		};
-		gpu {
+
+		gpu-thermal {
 			polling-delay-passive = <1000>;
 			polling-delay = <0>;
 
@@ -969,7 +980,8 @@
 				};
 			};
 		};
-		pllx {
+
+		pllx-thermal {
 			polling-delay-passive = <0>;
 			polling-delay = <0>;
 
diff --git a/arch/arm64/boot/dts/nvidia/tegra186-p2771-0000.dts b/arch/arm64/boot/dts/nvidia/tegra186-p2771-0000.dts
index 52fa258533e6..47cf2013afcc 100644
--- a/arch/arm64/boot/dts/nvidia/tegra186-p2771-0000.dts
+++ b/arch/arm64/boot/dts/nvidia/tegra186-p2771-0000.dts
@@ -811,6 +811,126 @@
 						remote-endpoint = <&mixer_out5_ep>;
 					};
 				};
+
+				xbar_asrc_in1_port: port@63 {
+					reg = <0x63>;
+
+					xbar_asrc_in1_ep: endpoint {
+						remote-endpoint = <&asrc_in1_ep>;
+					};
+				};
+
+				port@64 {
+					reg = <0x64>;
+
+					xbar_asrc_out1_ep: endpoint {
+						remote-endpoint = <&asrc_out1_ep>;
+					};
+				};
+
+				xbar_asrc_in2_port: port@65 {
+					reg = <0x65>;
+
+					xbar_asrc_in2_ep: endpoint {
+						remote-endpoint = <&asrc_in2_ep>;
+					};
+				};
+
+				port@66 {
+					reg = <0x66>;
+
+					xbar_asrc_out2_ep: endpoint {
+						remote-endpoint = <&asrc_out2_ep>;
+					};
+				};
+
+				xbar_asrc_in3_port: port@67 {
+					reg = <0x67>;
+
+					xbar_asrc_in3_ep: endpoint {
+						remote-endpoint = <&asrc_in3_ep>;
+					};
+				};
+
+				port@68 {
+					reg = <0x68>;
+
+					xbar_asrc_out3_ep: endpoint {
+						remote-endpoint = <&asrc_out3_ep>;
+					};
+				};
+
+				xbar_asrc_in4_port: port@69 {
+					reg = <0x69>;
+
+					xbar_asrc_in4_ep: endpoint {
+						remote-endpoint = <&asrc_in4_ep>;
+					};
+				};
+
+				port@6a {
+					reg = <0x6a>;
+
+					xbar_asrc_out4_ep: endpoint {
+						remote-endpoint = <&asrc_out4_ep>;
+					};
+				};
+
+				xbar_asrc_in5_port: port@6b {
+					reg = <0x6b>;
+
+					xbar_asrc_in5_ep: endpoint {
+						remote-endpoint = <&asrc_in5_ep>;
+					};
+				};
+
+				port@6c {
+					reg = <0x6c>;
+
+					xbar_asrc_out5_ep: endpoint {
+						remote-endpoint = <&asrc_out5_ep>;
+					};
+				};
+
+				xbar_asrc_in6_port: port@6d {
+					reg = <0x6d>;
+
+					xbar_asrc_in6_ep: endpoint {
+						remote-endpoint = <&asrc_in6_ep>;
+					};
+				};
+
+				port@6e {
+					reg = <0x6e>;
+
+					xbar_asrc_out6_ep: endpoint {
+						remote-endpoint = <&asrc_out6_ep>;
+					};
+				};
+
+				xbar_asrc_in7_port: port@6f {
+					reg = <0x6f>;
+
+					xbar_asrc_in7_ep: endpoint {
+						remote-endpoint = <&asrc_in7_ep>;
+					};
+				};
+
+				xbar_ope1_in_port: port@70 {
+					reg = <0x70>;
+
+					xbar_ope1_in_ep: endpoint {
+						remote-endpoint = <&ope1_cif_in_ep>;
+					};
+				};
+
+				port@71 {
+					reg = <0x71>;
+
+					xbar_ope1_out_ep: endpoint {
+						remote-endpoint = <&ope1_cif_out_ep>;
+					};
+				};
 			};
 
 			admaif@290f000 {
@@ -1807,6 +1927,31 @@
 				};
 			};
 
+			processing-engine@2908000 {
+				status = "okay";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0x0>;
+
+						ope1_cif_in_ep: endpoint {
+							remote-endpoint = <&xbar_ope1_in_ep>;
+						};
+					};
+
+					ope1_out_port: port@1 {
+						reg = <0x1>;
+
+						ope1_cif_out_ep: endpoint {
+							remote-endpoint = <&xbar_ope1_out_ep>;
+						};
+					};
+				};
+			};
+
 			amixer@290bb00 {
 				status = "okay";
 
@@ -1935,6 +2080,119 @@
 					};
 				};
 			};
+
+			asrc@2910000 {
+				status = "okay";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0x0>;
+
+						asrc_in1_ep: endpoint {
+							remote-endpoint = <&xbar_asrc_in1_ep>;
+						};
+					};
+
+					port@1 {
+						reg = <0x1>;
+
+						asrc_in2_ep: endpoint {
+							remote-endpoint = <&xbar_asrc_in2_ep>;
+						};
+					};
+
+					port@2 {
+						reg = <0x2>;
+
+						asrc_in3_ep: endpoint {
+							remote-endpoint = <&xbar_asrc_in3_ep>;
+						};
+					};
+
+					port@3 {
+						reg = <0x3>;
+
+						asrc_in4_ep: endpoint {
+							remote-endpoint = <&xbar_asrc_in4_ep>;
+						};
+					};
+
+					port@4 {
+						reg = <0x4>;
+
+						asrc_in5_ep: endpoint {
+							remote-endpoint = <&xbar_asrc_in5_ep>;
+						};
+					};
+
+					port@5 {
+						reg = <0x5>;
+
+						asrc_in6_ep: endpoint {
+							remote-endpoint = <&xbar_asrc_in6_ep>;
+						};
+					};
+
+					port@6 {
+						reg = <0x6>;
+
+						asrc_in7_ep: endpoint {
+							remote-endpoint = <&xbar_asrc_in7_ep>;
+						};
+					};
+
+					asrc_out1_port: port@7 {
+						reg = <0x7>;
+
+						asrc_out1_ep: endpoint {
+							remote-endpoint = <&xbar_asrc_out1_ep>;
+						};
+					};
+
+					asrc_out2_port: port@8 {
+						reg = <0x8>;
+
+						asrc_out2_ep: endpoint {
+							remote-endpoint = <&xbar_asrc_out2_ep>;
+						};
+					};
+
+					asrc_out3_port: port@9 {
+						reg = <0x9>;
+
+						asrc_out3_ep: endpoint {
+							remote-endpoint = <&xbar_asrc_out3_ep>;
+						};
+					};
+
+					asrc_out4_port: port@a {
+						reg = <0xa>;
+
+						asrc_out4_ep: endpoint {
+							remote-endpoint = <&xbar_asrc_out4_ep>;
+						};
+					};
+
+					asrc_out5_port: port@b {
+						reg = <0xb>;
+
+						asrc_out5_ep: endpoint {
+							remote-endpoint = <&xbar_asrc_out5_ep>;
+						};
+					};
+
+					asrc_out6_port:	port@c {
+						reg = <0xc>;
+
+						asrc_out6_ep: endpoint {
+							remote-endpoint = <&xbar_asrc_out6_ep>;
+						};
+					};
+				};
+			};
 		};
 	};
 
@@ -1945,19 +2203,19 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 
-			channel@0 {
+			input@0 {
 				reg = <0x0>;
 				label = "VDD_MUX";
 				shunt-resistor-micro-ohms = <20000>;
 			};
 
-			channel@1 {
+			input@1 {
 				reg = <0x1>;
 				label = "VDD_5V0_IO_SYS";
 				shunt-resistor-micro-ohms = <5000>;
 			};
 
-			channel@2 {
+			input@2 {
 				reg = <0x2>;
 				label = "VDD_3V3_SYS";
 				shunt-resistor-micro-ohms = <10000>;
@@ -1970,19 +2228,19 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 
-			channel@0 {
+			input@0 {
 				reg = <0x0>;
 				label = "VDD_3V3_IO_SLP";
 				shunt-resistor-micro-ohms = <10000>;
 			};
 
-			channel@1 {
+			input@1 {
 				reg = <0x1>;
 				label = "VDD_1V8_IO";
 				shunt-resistor-micro-ohms = <10000>;
 			};
 
-			channel@2 {
+			input@2 {
 				reg = <0x2>;
 				label = "VDD_M2_IN";
 				shunt-resistor-micro-ohms = <10000>;
@@ -2220,7 +2478,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		power {
+		key-power {
 			label = "Power";
 			gpios = <&gpio_aon TEGRA186_AON_GPIO(FF, 0)
 					   GPIO_ACTIVE_LOW>;
@@ -2231,7 +2489,7 @@
 			wakeup-source;
 		};
 
-		volume-up {
+		key-volume-up {
 			label = "Volume Up";
 			gpios = <&gpio_aon TEGRA186_AON_GPIO(FF, 1)
 					   GPIO_ACTIVE_LOW>;
@@ -2240,7 +2498,7 @@
 			debounce-interval = <10>;
 		};
 
-		volume-down {
+		key-volume-down {
 			label = "Volume Down";
 			gpios = <&gpio_aon TEGRA186_AON_GPIO(FF, 2)
 					   GPIO_ACTIVE_LOW>;
@@ -2250,7 +2508,7 @@
 		};
 	};
 
-	vdd_sd: regulator@100 {
+	vdd_sd: regulator-vdd-sd {
 		compatible = "regulator-fixed";
 		regulator-name = "SD_CARD_SW_PWR";
 		regulator-min-microvolt = <3300000>;
@@ -2262,7 +2520,7 @@
 		vin-supply = <&vdd_3v3_sys>;
 	};
 
-	vdd_hdmi: regulator@101 {
+	vdd_hdmi: regulator-vdd-hdmi {
 		compatible = "regulator-fixed";
 		regulator-name = "VDD_HDMI_5V0";
 		regulator-min-microvolt = <5000000>;
@@ -2274,7 +2532,7 @@
 		vin-supply = <&vdd_5v0_sys>;
 	};
 
-	vdd_usb0: regulator@102 {
+	vdd_usb0: regulator-vdd-usb0 {
 		compatible = "regulator-fixed";
 		regulator-name = "VDD_USB0";
 		regulator-min-microvolt = <5000000>;
@@ -2286,7 +2544,7 @@
 		vin-supply = <&vdd_5v0_sys>;
 	};
 
-	vdd_usb1: regulator@103 {
+	vdd_usb1: regulator-vdd-usb1 {
 		compatible = "regulator-fixed";
 		regulator-name = "VDD_USB1";
 		regulator-min-microvolt = <5000000>;
@@ -2331,6 +2589,11 @@
 		       <&xbar_mixer_in5_port>, <&xbar_mixer_in6_port>,
 		       <&xbar_mixer_in7_port>, <&xbar_mixer_in8_port>,
 		       <&xbar_mixer_in9_port>, <&xbar_mixer_in10_port>,
+		       <&xbar_asrc_in1_port>, <&xbar_asrc_in2_port>,
+		       <&xbar_asrc_in3_port>, <&xbar_asrc_in4_port>,
+		       <&xbar_asrc_in5_port>, <&xbar_asrc_in6_port>,
+		       <&xbar_asrc_in7_port>,
+		       <&xbar_ope1_in_port>,
 		       /* HW accelerators */
 		       <&sfc1_out_port>, <&sfc2_out_port>,
 		       <&sfc3_out_port>, <&sfc4_out_port>,
@@ -2348,6 +2611,9 @@
 		       <&mixer_out1_port>, <&mixer_out2_port>,
 		       <&mixer_out3_port>, <&mixer_out4_port>,
 		       <&mixer_out5_port>,
+		       <&asrc_out1_port>, <&asrc_out2_port>, <&asrc_out3_port>,
+		       <&asrc_out4_port>, <&asrc_out5_port>, <&asrc_out6_port>,
+		       <&ope1_out_port>,
 		       /* I/O */
 		       <&i2s1_port>, <&i2s2_port>, <&i2s3_port>, <&i2s4_port>,
 		       <&i2s5_port>, <&i2s6_port>, <&dmic1_port>, <&dmic2_port>,
diff --git a/arch/arm64/boot/dts/nvidia/tegra186-p3310.dtsi b/arch/arm64/boot/dts/nvidia/tegra186-p3310.dtsi
index fcd71bfc6707..aff857df25cf 100644
--- a/arch/arm64/boot/dts/nvidia/tegra186-p3310.dtsi
+++ b/arch/arm64/boot/dts/nvidia/tegra186-p3310.dtsi
@@ -44,7 +44,7 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 
-			phy: phy@0 {
+			phy: ethernet-phy@0 {
 				compatible = "ethernet-phy-ieee802.3-c22";
 				reg = <0x0>;
 				interrupt-parent = <&gpio>;
@@ -73,19 +73,19 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 
-			channel@0 {
+			input@0 {
 				reg = <0x0>;
 				label = "VDD_SYS_GPU";
 				shunt-resistor-micro-ohms = <10000>;
 			};
 
-			channel@1 {
+			input@1 {
 				reg = <0x1>;
 				label = "VDD_SYS_SOC";
 				shunt-resistor-micro-ohms = <10000>;
 			};
 
-			channel@2 {
+			input@2 {
 				reg = <0x2>;
 				label = "VDD_3V8_WIFI";
 				shunt-resistor-micro-ohms = <10000>;
@@ -98,19 +98,19 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 
-			channel@0 {
+			input@0 {
 				reg = <0x0>;
 				label = "VDD_IN";
 				shunt-resistor-micro-ohms = <5000>;
 			};
 
-			channel@1 {
+			input@1 {
 				reg = <0x1>;
 				label = "VDD_SYS_CPU";
 				shunt-resistor-micro-ohms = <10000>;
 			};
 
-			channel@2 {
+			input@2 {
 				reg = <0x2>;
 				label = "VDD_5V0_DDR";
 				shunt-resistor-micro-ohms = <10000>;
@@ -393,7 +393,7 @@
 		method = "smc";
 	};
 
-	gnd: regulator@0 {
+	gnd: regulator-gnd {
 		compatible = "regulator-fixed";
 		regulator-name = "GND";
 		regulator-min-microvolt = <0>;
@@ -402,7 +402,7 @@
 		regulator-boot-on;
 	};
 
-	vdd_5v0_sys: regulator@1 {
+	vdd_5v0_sys: regulator-vdd-5v0-sys {
 		compatible = "regulator-fixed";
 		regulator-name = "VDD_5V0_SYS";
 		regulator-min-microvolt = <5000000>;
@@ -411,7 +411,7 @@
 		regulator-boot-on;
 	};
 
-	vdd_1v8_ap: regulator@2 {
+	vdd_1v8_ap: regulator-vdd-1v8-ap {
 		compatible = "regulator-fixed";
 		regulator-name = "VDD_1V8_AP";
 		regulator-min-microvolt = <1800000>;
diff --git a/arch/arm64/boot/dts/nvidia/tegra186-p3509-0000+p3636-0001.dts b/arch/arm64/boot/dts/nvidia/tegra186-p3509-0000+p3636-0001.dts
index af33fe93e1d6..3e83a4d52eb1 100644
--- a/arch/arm64/boot/dts/nvidia/tegra186-p3509-0000+p3636-0001.dts
+++ b/arch/arm64/boot/dts/nvidia/tegra186-p3509-0000+p3636-0001.dts
@@ -46,7 +46,7 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 
-			phy: phy@0 {
+			phy: ethernet-phy@0 {
 				compatible = "ethernet-phy-ieee802.3-c22";
 				reg = <0x0>;
 				interrupt-parent = <&gpio_aon>;
@@ -81,22 +81,22 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 
-			channel@0 {
+			input@0 {
 				reg = <0>;
 				label = "VDD_IN";
 				shunt-resistor-micro-ohms = <5>;
 			};
 
-			channel@1 {
+			input@1 {
 				reg = <1>;
 				label = "VDD_CPU_GPU";
 				shunt-resistor-micro-ohms = <5>;
 			};
 
-			channel@2 {
+			input@2 {
 				reg = <2>;
 				label = "VDD_SOC";
-				shunt-resistor-micro-ohms = <>;
+				shunt-resistor-micro-ohms = <5>;
 			};
 		};
 	};
@@ -349,7 +349,7 @@
 		status = "okay";
 	};
 
-	fan: fan {
+	fan: pwm-fan {
 		compatible = "pwm-fan";
 		pwms = <&pwm4 0 45334>;
 
@@ -360,7 +360,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		power {
+		key-power {
 			label = "Power";
 			gpios = <&gpio_aon TEGRA186_AON_GPIO(FF, 0)
 					   GPIO_ACTIVE_LOW>;
@@ -371,7 +371,7 @@
 			wakeup-source;
 		};
 
-		volume-up {
+		key-volume-up {
 			label = "Volume Up";
 			gpios = <&gpio_aon TEGRA186_AON_GPIO(FF, 1)
 					   GPIO_ACTIVE_LOW>;
@@ -380,7 +380,7 @@
 			debounce-interval = <10>;
 		};
 
-		volume-down {
+		key-volume-down {
 			label = "Volume Down";
 			gpios = <&gpio_aon TEGRA186_AON_GPIO(FF, 2)
 					   GPIO_ACTIVE_LOW>;
@@ -593,7 +593,7 @@
 		method = "smc";
 	};
 
-	gnd: regulator@0 {
+	gnd: regulator-gnd {
 		compatible = "regulator-fixed";
 		regulator-name = "GND";
 		regulator-min-microvolt = <0>;
@@ -602,7 +602,7 @@
 		regulator-boot-on;
 	};
 
-	vdd_5v0_sys: regulator@1 {
+	vdd_5v0_sys: regulator-vdd-5v0-sys {
 		compatible = "regulator-fixed";
 		regulator-name = "VDD_5V0_SYS";
 		regulator-min-microvolt = <5000000>;
@@ -611,7 +611,7 @@
 		regulator-boot-on;
 	};
 
-	vdd_1v8_ap: regulator@2 {
+	vdd_1v8_ap: regulator-vdd-1v8-ap {
 		compatible = "regulator-fixed";
 		regulator-name = "VDD_1V8_AP";
 		regulator-min-microvolt = <1800000>;
@@ -623,7 +623,7 @@
 		vin-supply = <&vdd_1v8>;
 	};
 
-	vdd_hdmi: regulator@3 {
+	vdd_hdmi: regulator-vdd-hdmi {
 		compatible = "regulator-fixed";
 		regulator-name = "VDD_5V0_HDMI_CON";
 		regulator-min-microvolt = <5000000>;
@@ -633,7 +633,7 @@
 	};
 
 	thermal-zones {
-		cpu {
+		cpu-thermal {
 			polling-delay = <0>;
 			polling-delay-passive = <500>;
 			status = "okay";
@@ -687,28 +687,28 @@
 			};
 		};
 
-		gpu {
+		aux-thermal {
 			polling-delay = <0>;
 			polling-delay-passive = <500>;
 			status = "okay";
 
 			trips {
-				gpu_alert0: critical {
-					temperature = <99000>;
+				aux_alert0: critical {
+					temperature = <90000>;
 					hysteresis = <0>;
 					type = "critical";
 				};
 			};
 		};
 
-		aux {
+		gpu-thermal {
 			polling-delay = <0>;
 			polling-delay-passive = <500>;
 			status = "okay";
 
 			trips {
-				aux_alert0: critical {
-					temperature = <90000>;
+				gpu_alert0: critical {
+					temperature = <99000>;
 					hysteresis = <0>;
 					type = "critical";
 				};
diff --git a/arch/arm64/boot/dts/nvidia/tegra186.dtsi b/arch/arm64/boot/dts/nvidia/tegra186.dtsi
index 9ac4f0140700..6602fe421ee8 100644
--- a/arch/arm64/boot/dts/nvidia/tegra186.dtsi
+++ b/arch/arm64/boot/dts/nvidia/tegra186.dtsi
@@ -73,6 +73,48 @@
 		snps,rxpbl = <8>;
 	};
 
+	gpcdma: dma-controller@2600000 {
+		compatible = "nvidia,tegra186-gpcdma";
+		reg = <0x0 0x2600000 0x0 0x210000>;
+		resets = <&bpmp TEGRA186_RESET_GPCDMA>;
+		reset-names = "gpcdma";
+		interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>;
+		#dma-cells = <1>;
+		iommus = <&smmu TEGRA186_SID_GPCDMA_0>;
+		dma-coherent;
+		status = "okay";
+	};
+
 	aconnect@2900000 {
 		compatible = "nvidia,tegra186-aconnect",
 			     "nvidia,tegra210-aconnect";
@@ -467,6 +509,29 @@
 				status = "disabled";
 			};
 
+			tegra_ope1: processing-engine@2908000 {
+				compatible = "nvidia,tegra186-ope",
+					     "nvidia,tegra210-ope";
+				reg = <0x2908000 0x100>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges;
+				sound-name-prefix = "OPE1";
+				status = "disabled";
+
+				equalizer@2908100 {
+					compatible = "nvidia,tegra186-peq",
+						     "nvidia,tegra210-peq";
+					reg = <0x2908100 0x100>;
+				};
+
+				dynamic-range-compressor@2908200 {
+					compatible = "nvidia,tegra186-mbdrc",
+						     "nvidia,tegra210-mbdrc";
+					reg = <0x2908200 0x200>;
+				};
+			};
+
 			tegra_amixer: amixer@290bb00 {
 				compatible = "nvidia,tegra186-amixer",
 					     "nvidia,tegra210-amixer";
@@ -474,12 +539,25 @@
 				sound-name-prefix = "MIXER1";
 				status = "disabled";
 			};
+
+			tegra_asrc: asrc@2910000 {
+				compatible = "nvidia,tegra186-asrc";
+				reg = <0x2910000 0x2000>;
+				sound-name-prefix = "ASRC1";
+				status = "disabled";
+			};
 		};
 	};
 
 	mc: memory-controller@2c00000 {
 		compatible = "nvidia,tegra186-mc";
-		reg = <0x0 0x02c00000 0x0 0xb0000>;
+		reg = <0x0 0x02c00000 0x0 0x10000>,    /* MC-SID */
+		      <0x0 0x02c10000 0x0 0x10000>,    /* Broadcast channel */
+		      <0x0 0x02c20000 0x0 0x10000>,    /* MC0 */
+		      <0x0 0x02c30000 0x0 0x10000>,    /* MC1 */
+		      <0x0 0x02c40000 0x0 0x10000>,    /* MC2 */
+		      <0x0 0x02c50000 0x0 0x10000>;    /* MC3 */
+		reg-names = "sid", "broadcast", "ch0", "ch1", "ch2", "ch3";
 		interrupts = <GIC_SPI 223 IRQ_TYPE_LEVEL_HIGH>;
 		status = "disabled";
 
@@ -508,6 +586,22 @@
 		};
 	};
 
+	timer@3010000 {
+		compatible = "nvidia,tegra186-timer";
+		reg = <0x0 0x03010000 0x0 0x000e0000>;
+		interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+		status = "okay";
+	};
+
 	uarta: serial@3100000 {
 		compatible = "nvidia,tegra186-uart", "nvidia,tegra20-uart";
 		reg = <0x0 0x03100000 0x0 0x40>;
@@ -569,7 +663,7 @@
 	};
 
 	gen1_i2c: i2c@3160000 {
-		compatible = "nvidia,tegra186-i2c", "nvidia,tegra210-i2c";
+		compatible = "nvidia,tegra186-i2c";
 		reg = <0x0 0x03160000 0x0 0x10000>;
 		interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
 		#address-cells = <1>;
@@ -578,11 +672,15 @@
 		clock-names = "div-clk";
 		resets = <&bpmp TEGRA186_RESET_I2C1>;
 		reset-names = "i2c";
+		iommus = <&smmu TEGRA186_SID_GPCDMA_0>;
+		dma-coherent;
+		dmas = <&gpcdma 21>, <&gpcdma 21>;
+		dma-names = "rx", "tx";
 		status = "disabled";
 	};
 
 	cam_i2c: i2c@3180000 {
-		compatible = "nvidia,tegra186-i2c", "nvidia,tegra210-i2c";
+		compatible = "nvidia,tegra186-i2c";
 		reg = <0x0 0x03180000 0x0 0x10000>;
 		interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>;
 		#address-cells = <1>;
@@ -591,12 +689,16 @@
 		clock-names = "div-clk";
 		resets = <&bpmp TEGRA186_RESET_I2C3>;
 		reset-names = "i2c";
+		iommus = <&smmu TEGRA186_SID_GPCDMA_0>;
+		dma-coherent;
+		dmas = <&gpcdma 23>, <&gpcdma 23>;
+		dma-names = "rx", "tx";
 		status = "disabled";
 	};
 
 	/* shares pads with dpaux1 */
 	dp_aux_ch1_i2c: i2c@3190000 {
-		compatible = "nvidia,tegra186-i2c", "nvidia,tegra210-i2c";
+		compatible = "nvidia,tegra186-i2c";
 		reg = <0x0 0x03190000 0x0 0x10000>;
 		interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
 		#address-cells = <1>;
@@ -608,12 +710,16 @@
 		pinctrl-names = "default", "idle";
 		pinctrl-0 = <&state_dpaux1_i2c>;
 		pinctrl-1 = <&state_dpaux1_off>;
+		iommus = <&smmu TEGRA186_SID_GPCDMA_0>;
+		dma-coherent;
+		dmas = <&gpcdma 26>, <&gpcdma 26>;
+		dma-names = "rx", "tx";
 		status = "disabled";
 	};
 
 	/* controlled by BPMP, should not be enabled */
 	pwr_i2c: i2c@31a0000 {
-		compatible = "nvidia,tegra186-i2c", "nvidia,tegra210-i2c";
+		compatible = "nvidia,tegra186-i2c";
 		reg = <0x0 0x031a0000 0x0 0x10000>;
 		interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
 		#address-cells = <1>;
@@ -627,7 +733,7 @@
 
 	/* shares pads with dpaux0 */
 	dp_aux_ch0_i2c: i2c@31b0000 {
-		compatible = "nvidia,tegra186-i2c", "nvidia,tegra210-i2c";
+		compatible = "nvidia,tegra186-i2c";
 		reg = <0x0 0x031b0000 0x0 0x10000>;
 		interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
 		#address-cells = <1>;
@@ -639,11 +745,15 @@
 		pinctrl-names = "default", "idle";
 		pinctrl-0 = <&state_dpaux_i2c>;
 		pinctrl-1 = <&state_dpaux_off>;
+		iommus = <&smmu TEGRA186_SID_GPCDMA_0>;
+		dma-coherent;
+		dmas = <&gpcdma 30>, <&gpcdma 30>;
+		dma-names = "rx", "tx";
 		status = "disabled";
 	};
 
 	gen7_i2c: i2c@31c0000 {
-		compatible = "nvidia,tegra186-i2c", "nvidia,tegra210-i2c";
+		compatible = "nvidia,tegra186-i2c";
 		reg = <0x0 0x031c0000 0x0 0x10000>;
 		interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
 		#address-cells = <1>;
@@ -652,11 +762,15 @@
 		clock-names = "div-clk";
 		resets = <&bpmp TEGRA186_RESET_I2C7>;
 		reset-names = "i2c";
+		iommus = <&smmu TEGRA186_SID_GPCDMA_0>;
+		dma-coherent;
+		dmas = <&gpcdma 27>, <&gpcdma 27>;
+		dma-names = "rx", "tx";
 		status = "disabled";
 	};
 
 	gen9_i2c: i2c@31e0000 {
-		compatible = "nvidia,tegra186-i2c", "nvidia,tegra210-i2c";
+		compatible = "nvidia,tegra186-i2c";
 		reg = <0x0 0x031e0000 0x0 0x10000>;
 		interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
 		#address-cells = <1>;
@@ -665,6 +779,10 @@
 		clock-names = "div-clk";
 		resets = <&bpmp TEGRA186_RESET_I2C9>;
 		reset-names = "i2c";
+		iommus = <&smmu TEGRA186_SID_GPCDMA_0>;
+		dma-coherent;
+		dmas = <&gpcdma 31>, <&gpcdma 31>;
+		dma-names = "rx", "tx";
 		status = "disabled";
 	};
 
@@ -1073,7 +1191,7 @@
 	};
 
 	gen2_i2c: i2c@c240000 {
-		compatible = "nvidia,tegra186-i2c", "nvidia,tegra210-i2c";
+		compatible = "nvidia,tegra186-i2c";
 		reg = <0x0 0x0c240000 0x0 0x10000>;
 		interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
 		#address-cells = <1>;
@@ -1082,11 +1200,15 @@
 		clock-names = "div-clk";
 		resets = <&bpmp TEGRA186_RESET_I2C2>;
 		reset-names = "i2c";
+		iommus = <&smmu TEGRA186_SID_GPCDMA_0>;
+		dma-coherent;
+		dmas = <&gpcdma 22>, <&gpcdma 22>;
+		dma-names = "rx", "tx";
 		status = "disabled";
 	};
 
 	gen8_i2c: i2c@c250000 {
-		compatible = "nvidia,tegra186-i2c", "nvidia,tegra210-i2c";
+		compatible = "nvidia,tegra186-i2c";
 		reg = <0x0 0x0c250000 0x0 0x10000>;
 		interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
 		#address-cells = <1>;
@@ -1095,6 +1217,10 @@
 		clock-names = "div-clk";
 		resets = <&bpmp TEGRA186_RESET_I2C8>;
 		reset-names = "i2c";
+		iommus = <&smmu TEGRA186_SID_GPCDMA_0>;
+		dma-coherent;
+		dmas = <&gpcdma 0>, <&gpcdma 0>;
+		dma-names = "rx", "tx";
 		status = "disabled";
 	};
 
@@ -1199,7 +1325,7 @@
 
 	ccplex@e000000 {
 		compatible = "nvidia,tegra186-ccplex-cluster";
-		reg = <0x0 0x0e000000 0x0 0x3fffff>;
+		reg = <0x0 0x0e000000 0x0 0x400000>;
 
 		nvidia,bpmp = <&bpmp>;
 	};
@@ -1390,6 +1516,16 @@
 
 		iommus = <&smmu TEGRA186_SID_HOST1X>;
 
+		/* Context isolation domains */
+		iommu-map = <0 &smmu TEGRA186_SID_HOST1X_CTX0 1>,
+			    <1 &smmu TEGRA186_SID_HOST1X_CTX1 1>,
+			    <2 &smmu TEGRA186_SID_HOST1X_CTX2 1>,
+			    <3 &smmu TEGRA186_SID_HOST1X_CTX3 1>,
+			    <4 &smmu TEGRA186_SID_HOST1X_CTX4 1>,
+			    <5 &smmu TEGRA186_SID_HOST1X_CTX5 1>,
+			    <6 &smmu TEGRA186_SID_HOST1X_CTX6 1>,
+			    <7 &smmu TEGRA186_SID_HOST1X_CTX7 1>;
+
 		dpaux1: dpaux@15040000 {
 			compatible = "nvidia,tegra186-dpaux";
 			reg = <0x15040000 0x10000>;
@@ -1538,6 +1674,21 @@
 			iommus = <&smmu TEGRA186_SID_VIC>;
 		};
 
+		nvjpg@15380000 {
+			compatible = "nvidia,tegra186-nvjpg";
+			reg = <0x15380000 0x40000>;
+			clocks = <&bpmp TEGRA186_CLK_NVJPG>;
+			clock-names = "nvjpg";
+			resets = <&bpmp TEGRA186_RESET_NVJPG>;
+			reset-names = "nvjpg";
+
+			power-domains = <&bpmp TEGRA186_POWER_DOMAIN_NVJPG>;
+			interconnects = <&mc TEGRA186_MEMORY_CLIENT_NVJPGSRD &emc>,
+					<&mc TEGRA186_MEMORY_CLIENT_NVJPGSWR &emc>;
+			interconnect-names = "dma-mem", "write";
+			iommus = <&smmu TEGRA186_SID_NVJPG>;
+		};
+
 		dsib: dsi@15400000 {
 			compatible = "nvidia,tegra186-dsi";
 			reg = <0x15400000 0x10000>;
@@ -1569,6 +1720,21 @@
 			iommus = <&smmu TEGRA186_SID_NVDEC>;
 		};
 
+		nvenc@154c0000 {
+			compatible = "nvidia,tegra186-nvenc";
+			reg = <0x154c0000 0x40000>;
+			clocks = <&bpmp TEGRA186_CLK_NVENC>;
+			clock-names = "nvenc";
+			resets = <&bpmp TEGRA186_RESET_NVENC>;
+			reset-names = "nvenc";
+
+			power-domains = <&bpmp TEGRA186_POWER_DOMAIN_MPE>;
+			interconnects = <&mc TEGRA186_MEMORY_CLIENT_NVENCSRD &emc>,
+					<&mc TEGRA186_MEMORY_CLIENT_NVENCSWR &emc>;
+			interconnect-names = "dma-mem", "write";
+			iommus = <&smmu TEGRA186_SID_NVENC>;
+		};
+
 		sor0: sor@15540000 {
 			compatible = "nvidia,tegra186-sor";
 			reg = <0x15540000 0x10000>;
@@ -1719,6 +1885,7 @@
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0x0 0x0 0x30000000 0x50000>;
+		no-memory-wc;
 
 		cpu_bpmp_tx: sram@4e000 {
 			reg = <0x4e000 0x1000>;
@@ -1771,7 +1938,7 @@
 		iommus = <&smmu TEGRA186_SID_BPMP>;
 		mboxes = <&hsp_top0 TEGRA_HSP_MBOX_TYPE_DB
 				    TEGRA_HSP_DB_MASTER_BPMP>;
-		shmem = <&cpu_bpmp_tx &cpu_bpmp_rx>;
+		shmem = <&cpu_bpmp_tx>, <&cpu_bpmp_rx>;
 		#clock-cells = <1>;
 		#reset-cells = <1>;
 		#power-domain-cells = <1>;
@@ -1892,14 +2059,14 @@
 	};
 
 	pmu_denver {
-		compatible = "nvidia,denver-pmu", "arm,armv8-pmuv3";
+		compatible = "nvidia,denver-pmu";
 		interrupts = <GIC_SPI 320 IRQ_TYPE_LEVEL_HIGH>,
 			     <GIC_SPI 321 IRQ_TYPE_LEVEL_HIGH>;
 		interrupt-affinity = <&denver_0 &denver_1>;
 	};
 
 	pmu_a57 {
-		compatible = "arm,cortex-a57-pmu", "arm,armv8-pmuv3";
+		compatible = "arm,cortex-a57-pmu";
 		interrupts = <GIC_SPI 296 IRQ_TYPE_LEVEL_HIGH>,
 			     <GIC_SPI 297 IRQ_TYPE_LEVEL_HIGH>,
 			     <GIC_SPI 298 IRQ_TYPE_LEVEL_HIGH>,
@@ -1930,12 +2097,12 @@
 	};
 
 	thermal-zones {
-		a57 {
+		/* Cortex-A57 cluster */
+		cpu-thermal {
 			polling-delay = <0>;
 			polling-delay-passive = <1000>;
 
-			thermal-sensors =
-				<&bpmp_thermal TEGRA186_BPMP_THERMAL_ZONE_CPU>;
+			thermal-sensors = <&bpmp_thermal TEGRA186_BPMP_THERMAL_ZONE_CPU>;
 
 			trips {
 				critical {
@@ -1949,12 +2116,12 @@
 			};
 		};
 
-		denver {
+		/* Denver cluster */
+		aux-thermal {
 			polling-delay = <0>;
 			polling-delay-passive = <1000>;
 
-			thermal-sensors =
-				<&bpmp_thermal TEGRA186_BPMP_THERMAL_ZONE_AUX>;
+			thermal-sensors = <&bpmp_thermal TEGRA186_BPMP_THERMAL_ZONE_AUX>;
 
 			trips {
 				critical {
@@ -1968,12 +2135,11 @@
 			};
 		};
 
-		gpu {
+		gpu-thermal {
 			polling-delay = <0>;
 			polling-delay-passive = <1000>;
 
-			thermal-sensors =
-				<&bpmp_thermal TEGRA186_BPMP_THERMAL_ZONE_GPU>;
+			thermal-sensors = <&bpmp_thermal TEGRA186_BPMP_THERMAL_ZONE_GPU>;
 
 			trips {
 				critical {
@@ -1987,12 +2153,11 @@
 			};
 		};
 
-		pll {
+		pll-thermal {
 			polling-delay = <0>;
 			polling-delay-passive = <1000>;
 
-			thermal-sensors =
-				<&bpmp_thermal TEGRA186_BPMP_THERMAL_ZONE_PLLX>;
+			thermal-sensors = <&bpmp_thermal TEGRA186_BPMP_THERMAL_ZONE_PLLX>;
 
 			trips {
 				critical {
@@ -2006,12 +2171,11 @@
 			};
 		};
 
-		always_on {
+		ao-thermal {
 			polling-delay = <0>;
 			polling-delay-passive = <1000>;
 
-			thermal-sensors =
-				<&bpmp_thermal TEGRA186_BPMP_THERMAL_ZONE_AO>;
+			thermal-sensors = <&bpmp_thermal TEGRA186_BPMP_THERMAL_ZONE_AO>;
 
 			trips {
 				critical {
diff --git a/arch/arm64/boot/dts/nvidia/tegra194-p2888.dtsi b/arch/arm64/boot/dts/nvidia/tegra194-p2888.dtsi
index c4058ee36fec..b0f9393dd39c 100644
--- a/arch/arm64/boot/dts/nvidia/tegra194-p2888.dtsi
+++ b/arch/arm64/boot/dts/nvidia/tegra194-p2888.dtsi
@@ -39,7 +39,7 @@
 				#address-cells = <1>;
 				#size-cells = <0>;
 
-				phy: phy@0 {
+				phy: ethernet-phy@0 {
 					compatible = "ethernet-phy-ieee802.3-c22";
 					reg = <0x0>;
 					interrupt-parent = <&gpio>;
@@ -75,7 +75,7 @@
 
 		/* SDMMC1 (SD/MMC) */
 		mmc@3400000 {
-			cd-gpios = <&gpio TEGRA194_MAIN_GPIO(A, 0) GPIO_ACTIVE_LOW>;
+			cd-gpios = <&gpio TEGRA194_MAIN_GPIO(G, 7) GPIO_ACTIVE_LOW>;
 		};
 
 		/* SDMMC4 (eMMC) */
@@ -317,7 +317,7 @@
 		};
 	};
 
-	vdd_5v0_sys: regulator@0 {
+	vdd_5v0_sys: regulator-vdd-5v0-sys {
 		compatible = "regulator-fixed";
 		regulator-name = "VIN_SYS_5V0";
 		regulator-min-microvolt = <5000000>;
@@ -326,7 +326,7 @@
 		regulator-boot-on;
 	};
 
-	vdd_hdmi: regulator@1 {
+	vdd_hdmi: regulator-vdd-hdmi {
 		compatible = "regulator-fixed";
 		regulator-name = "VDD_5V0_HDMI_CON";
 		regulator-min-microvolt = <5000000>;
@@ -335,7 +335,7 @@
 		enable-active-high;
 	};
 
-	vdd_3v3_pcie: regulator@2 {
+	vdd_3v3_pcie: regulator-vdd-3v3-pcie {
 		compatible = "regulator-fixed";
 		regulator-name = "PEX_3V3";
 		regulator-min-microvolt = <3300000>;
@@ -345,7 +345,7 @@
 		enable-active-high;
 	};
 
-	vdd_12v_pcie: regulator@3 {
+	vdd_12v_pcie: regulator-vdd-12v-pcie {
 		compatible = "regulator-fixed";
 		regulator-name = "VDD_12V";
 		regulator-min-microvolt = <1200000>;
@@ -354,7 +354,7 @@
 		regulator-boot-on;
 	};
 
-	vdd_5v_sata: regulator@4 {
+	vdd_5v_sata: regulator-vdd-5v0-sata {
 		compatible = "regulator-fixed";
 		regulator-name = "VDD_5V_SATA";
 		regulator-min-microvolt = <5000000>;
diff --git a/arch/arm64/boot/dts/nvidia/tegra194-p2972-0000.dts b/arch/arm64/boot/dts/nvidia/tegra194-p2972-0000.dts
index 9f34871b8f60..bc1041d11f6d 100644
--- a/arch/arm64/boot/dts/nvidia/tegra194-p2972-0000.dts
+++ b/arch/arm64/boot/dts/nvidia/tegra194-p2972-0000.dts
@@ -764,6 +764,126 @@
 							remote-endpoint = <&mixer_out5_ep>;
 						};
 					};
+
+					xbar_asrc_in1_port: port@63 {
+						reg = <0x63>;
+
+						xbar_asrc_in1_ep: endpoint {
+							remote-endpoint = <&asrc_in1_ep>;
+						};
+					};
+
+					port@64 {
+						reg = <0x64>;
+
+						xbar_asrc_out1_ep: endpoint {
+							remote-endpoint = <&asrc_out1_ep>;
+						};
+					};
+
+					xbar_asrc_in2_port: port@65 {
+						reg = <0x65>;
+
+						xbar_asrc_in2_ep: endpoint {
+							remote-endpoint = <&asrc_in2_ep>;
+						};
+					};
+
+					port@66 {
+						reg = <0x66>;
+
+						xbar_asrc_out2_ep: endpoint {
+							remote-endpoint = <&asrc_out2_ep>;
+						};
+					};
+
+					xbar_asrc_in3_port: port@67 {
+						reg = <0x67>;
+
+						xbar_asrc_in3_ep: endpoint {
+							remote-endpoint = <&asrc_in3_ep>;
+						};
+					};
+
+					port@68 {
+						reg = <0x68>;
+
+						xbar_asrc_out3_ep: endpoint {
+							remote-endpoint = <&asrc_out3_ep>;
+						};
+					};
+
+					xbar_asrc_in4_port: port@69 {
+						reg = <0x69>;
+
+						xbar_asrc_in4_ep: endpoint {
+							remote-endpoint = <&asrc_in4_ep>;
+						};
+					};
+
+					port@6a {
+						reg = <0x6a>;
+
+						xbar_asrc_out4_ep: endpoint {
+							remote-endpoint = <&asrc_out4_ep>;
+						};
+					};
+
+					xbar_asrc_in5_port: port@6b {
+						reg = <0x6b>;
+
+						xbar_asrc_in5_ep: endpoint {
+							remote-endpoint = <&asrc_in5_ep>;
+						};
+					};
+
+					port@6c {
+						reg = <0x6c>;
+
+						xbar_asrc_out5_ep: endpoint {
+							remote-endpoint = <&asrc_out5_ep>;
+						};
+					};
+
+					xbar_asrc_in6_port: port@6d {
+						reg = <0x6d>;
+
+						xbar_asrc_in6_ep: endpoint {
+							remote-endpoint = <&asrc_in6_ep>;
+						};
+					};
+
+					port@6e {
+						reg = <0x6e>;
+
+						xbar_asrc_out6_ep: endpoint {
+							remote-endpoint = <&asrc_out6_ep>;
+						};
+					};
+
+					xbar_asrc_in7_port: port@6f {
+						reg = <0x6f>;
+
+						xbar_asrc_in7_ep: endpoint {
+							remote-endpoint = <&asrc_in7_ep>;
+						};
+					};
+
+					xbar_ope1_in_port: port@70 {
+						reg = <0x70>;
+
+						xbar_ope1_in_ep: endpoint {
+							remote-endpoint = <&ope1_cif_in_ep>;
+						};
+					};
+
+					port@71 {
+						reg = <0x71>;
+
+						xbar_ope1_out_ep: endpoint {
+							remote-endpoint = <&ope1_cif_out_ep>;
+						};
+					};
 				};
 
 				admaif@290f000 {
@@ -1031,7 +1151,7 @@
 						i2s6_port: port@1 {
 							reg = <1>;
 
-							i2s6_dap_ep: endpoint@0 {
+							i2s6_dap_ep: endpoint {
 								dai-format = "i2s";
 								/* Place holder for external Codec */
 							};
@@ -1606,6 +1726,31 @@
 					};
 				};
 
+				processing-engine@2908000 {
+					status = "okay";
+
+					ports {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						port@0 {
+							reg = <0x0>;
+
+							ope1_cif_in_ep: endpoint {
+								remote-endpoint = <&xbar_ope1_in_ep>;
+							};
+						};
+
+						ope1_out_port: port@1 {
+							reg = <0x1>;
+
+							ope1_cif_out_ep: endpoint {
+								remote-endpoint = <&xbar_ope1_out_ep>;
+							};
+						};
+					};
+				};
+
 				amixer@290bb00 {
 					status = "okay";
 
@@ -1734,6 +1879,119 @@
 						};
 					};
 				};
+
+				asrc@2910000 {
+					status = "okay";
+
+					ports {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						port@0 {
+							reg = <0x0>;
+
+							asrc_in1_ep: endpoint {
+								remote-endpoint = <&xbar_asrc_in1_ep>;
+							};
+						};
+
+						port@1 {
+							reg = <0x1>;
+
+							asrc_in2_ep: endpoint {
+								remote-endpoint = <&xbar_asrc_in2_ep>;
+							};
+						};
+
+						port@2 {
+							reg = <0x2>;
+
+							asrc_in3_ep: endpoint {
+								remote-endpoint = <&xbar_asrc_in3_ep>;
+							};
+						};
+
+						port@3 {
+							reg = <0x3>;
+
+							asrc_in4_ep: endpoint {
+								remote-endpoint = <&xbar_asrc_in4_ep>;
+							};
+						};
+
+						port@4 {
+							reg = <0x4>;
+
+							asrc_in5_ep: endpoint {
+								remote-endpoint = <&xbar_asrc_in5_ep>;
+							};
+						};
+
+						port@5 {
+							reg = <0x5>;
+
+							asrc_in6_ep: endpoint {
+								remote-endpoint = <&xbar_asrc_in6_ep>;
+							};
+						};
+
+						port@6 {
+							reg = <0x6>;
+
+							asrc_in7_ep: endpoint {
+								remote-endpoint = <&xbar_asrc_in7_ep>;
+							};
+						};
+
+						asrc_out1_port: port@7 {
+							reg = <0x7>;
+
+							asrc_out1_ep: endpoint {
+								remote-endpoint = <&xbar_asrc_out1_ep>;
+							};
+						};
+
+						asrc_out2_port: port@8 {
+							reg = <0x8>;
+
+							asrc_out2_ep: endpoint {
+								remote-endpoint = <&xbar_asrc_out2_ep>;
+							};
+						};
+
+						asrc_out3_port: port@9 {
+							reg = <0x9>;
+
+							asrc_out3_ep: endpoint {
+								remote-endpoint = <&xbar_asrc_out3_ep>;
+							};
+						};
+
+						asrc_out4_port: port@a {
+							reg = <0xa>;
+
+							asrc_out4_ep: endpoint {
+								remote-endpoint = <&xbar_asrc_out4_ep>;
+							};
+						};
+
+						asrc_out5_port: port@b {
+							reg = <0xb>;
+
+							asrc_out5_ep: endpoint {
+								remote-endpoint = <&xbar_asrc_out5_ep>;
+							};
+						};
+
+						asrc_out6_port:	port@c {
+							reg = <0xc>;
+
+							asrc_out6_ep: endpoint {
+								remote-endpoint = <&xbar_asrc_out6_ep>;
+							};
+						};
+					};
+				};
 			};
 		};
 
@@ -1989,7 +2247,7 @@
 			    "p2u-5", "p2u-6", "p2u-7";
 	};
 
-	fan: fan {
+	fan: pwm-fan {
 		compatible = "pwm-fan";
 		pwms = <&pwm4 0 45334>;
 
@@ -2000,7 +2258,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		force-recovery {
+		key-force-recovery {
 			label = "Force Recovery";
 			gpios = <&gpio TEGRA194_MAIN_GPIO(G, 0)
 				       GPIO_ACTIVE_LOW>;
@@ -2009,7 +2267,7 @@
 			debounce-interval = <10>;
 		};
 
-		power {
+		key-power {
 			label = "Power";
 			gpios = <&gpio_aon TEGRA194_AON_GPIO(EE, 4)
 					   GPIO_ACTIVE_LOW>;
@@ -2052,6 +2310,11 @@
 		       <&xbar_mixer_in5_port>, <&xbar_mixer_in6_port>,
 		       <&xbar_mixer_in7_port>, <&xbar_mixer_in8_port>,
 		       <&xbar_mixer_in9_port>, <&xbar_mixer_in10_port>,
+		       <&xbar_asrc_in1_port>, <&xbar_asrc_in2_port>,
+		       <&xbar_asrc_in3_port>, <&xbar_asrc_in4_port>,
+		       <&xbar_asrc_in5_port>, <&xbar_asrc_in6_port>,
+		       <&xbar_asrc_in7_port>,
+		       <&xbar_ope1_in_port>,
 		       /* HW accelerators */
 		       <&sfc1_out_port>, <&sfc2_out_port>,
 		       <&sfc3_out_port>, <&sfc4_out_port>,
@@ -2068,6 +2331,9 @@
 		       <&adx4_out3_port>, <&adx4_out4_port>,
 		       <&mixer_out1_port>, <&mixer_out2_port>, <&mixer_out3_port>,
 		       <&mixer_out4_port>, <&mixer_out5_port>,
+		       <&asrc_out1_port>, <&asrc_out2_port>, <&asrc_out3_port>,
+		       <&asrc_out4_port>, <&asrc_out5_port>, <&asrc_out6_port>,
+		       <&ope1_out_port>,
 		       /* BE I/O Ports */
 		       <&i2s1_port>, <&i2s2_port>, <&i2s4_port>, <&i2s6_port>,
 		       <&dmic3_port>;
@@ -2097,7 +2363,7 @@
 	};
 
 	thermal-zones {
-		cpu {
+		cpu-thermal {
 			polling-delay = <0>;
 			polling-delay-passive = <500>;
 			status = "okay";
@@ -2151,7 +2417,7 @@
 			};
 		};
 
-		gpu {
+		gpu-thermal {
 			polling-delay = <0>;
 			polling-delay-passive = <500>;
 			status = "okay";
@@ -2165,7 +2431,7 @@
 			};
 		};
 
-		aux {
+		aux-thermal {
 			polling-delay = <0>;
 			polling-delay-passive = <500>;
 			status = "okay";
diff --git a/arch/arm64/boot/dts/nvidia/tegra194-p3509-0000.dtsi b/arch/arm64/boot/dts/nvidia/tegra194-p3509-0000.dtsi
index a055f17218bb..273a1ef716b6 100644
--- a/arch/arm64/boot/dts/nvidia/tegra194-p3509-0000.dtsi
+++ b/arch/arm64/boot/dts/nvidia/tegra194-p3509-0000.dtsi
@@ -774,6 +774,126 @@
 							remote-endpoint = <&mixer_out5_ep>;
 						};
 					};
+
+					xbar_asrc_in1_port: port@63 {
+						reg = <0x63>;
+
+						xbar_asrc_in1_ep: endpoint {
+							remote-endpoint = <&asrc_in1_ep>;
+						};
+					};
+
+					port@64 {
+						reg = <0x64>;
+
+						xbar_asrc_out1_ep: endpoint {
+							remote-endpoint = <&asrc_out1_ep>;
+						};
+					};
+
+					xbar_asrc_in2_port: port@65 {
+						reg = <0x65>;
+
+						xbar_asrc_in2_ep: endpoint {
+							remote-endpoint = <&asrc_in2_ep>;
+						};
+					};
+
+					port@66 {
+						reg = <0x66>;
+
+						xbar_asrc_out2_ep: endpoint {
+							remote-endpoint = <&asrc_out2_ep>;
+						};
+					};
+
+					xbar_asrc_in3_port: port@67 {
+						reg = <0x67>;
+
+						xbar_asrc_in3_ep: endpoint {
+							remote-endpoint = <&asrc_in3_ep>;
+						};
+					};
+
+					port@68 {
+						reg = <0x68>;
+
+						xbar_asrc_out3_ep: endpoint {
+							remote-endpoint = <&asrc_out3_ep>;
+						};
+					};
+
+					xbar_asrc_in4_port: port@69 {
+						reg = <0x69>;
+
+						xbar_asrc_in4_ep: endpoint {
+							remote-endpoint = <&asrc_in4_ep>;
+						};
+					};
+
+					port@6a {
+						reg = <0x6a>;
+
+						xbar_asrc_out4_ep: endpoint {
+							remote-endpoint = <&asrc_out4_ep>;
+						};
+					};
+
+					xbar_asrc_in5_port: port@6b {
+						reg = <0x6b>;
+
+						xbar_asrc_in5_ep: endpoint {
+							remote-endpoint = <&asrc_in5_ep>;
+						};
+					};
+
+					port@6c {
+						reg = <0x6c>;
+
+						xbar_asrc_out5_ep: endpoint {
+							remote-endpoint = <&asrc_out5_ep>;
+						};
+					};
+
+					xbar_asrc_in6_port: port@6d {
+						reg = <0x6d>;
+
+						xbar_asrc_in6_ep: endpoint {
+							remote-endpoint = <&asrc_in6_ep>;
+						};
+					};
+
+					port@6e {
+						reg = <0x6e>;
+
+						xbar_asrc_out6_ep: endpoint {
+							remote-endpoint = <&asrc_out6_ep>;
+						};
+					};
+
+					xbar_asrc_in7_port: port@6f {
+						reg = <0x6f>;
+
+						xbar_asrc_in7_ep: endpoint {
+							remote-endpoint = <&asrc_in7_ep>;
+						};
+					};
+
+					xbar_ope1_in_port: port@70 {
+						reg = <0x70>;
+
+						xbar_ope1_in_ep: endpoint {
+							remote-endpoint = <&ope1_cif_in_ep>;
+						};
+					};
+
+					port@71 {
+						reg = <0x71>;
+
+						xbar_ope1_out_ep: endpoint {
+							remote-endpoint = <&ope1_cif_out_ep>;
+						};
+					};
 				};
 
 				admaif@290f000 {
@@ -989,7 +1109,7 @@
 						i2s5_port: port@1 {
 							reg = <1>;
 
-							i2s5_dap_ep: endpoint@0 {
+							i2s5_dap_ep: endpoint {
 								dai-format = "i2s";
 								/* Place holder for external Codec */
 							};
@@ -1666,6 +1786,31 @@
 					};
 				};
 
+				processing-engine@2908000 {
+					status = "okay";
+
+					ports {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						port@0 {
+							reg = <0x0>;
+
+							ope1_cif_in_ep: endpoint {
+								remote-endpoint = <&xbar_ope1_in_ep>;
+							};
+						};
+
+						ope1_out_port: port@1 {
+							reg = <0x1>;
+
+							ope1_cif_out_ep: endpoint {
+								remote-endpoint = <&xbar_ope1_out_ep>;
+							};
+						};
+					};
+				};
+
 				amixer@290bb00 {
 					status = "okay";
 
@@ -1794,6 +1939,119 @@
 						};
 					};
 				};
+
+				asrc@2910000 {
+					status = "okay";
+
+					ports {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						port@0 {
+							reg = <0x0>;
+
+							asrc_in1_ep: endpoint {
+								remote-endpoint = <&xbar_asrc_in1_ep>;
+							};
+						};
+
+						port@1 {
+							reg = <0x1>;
+
+							asrc_in2_ep: endpoint {
+								remote-endpoint = <&xbar_asrc_in2_ep>;
+							};
+						};
+
+						port@2 {
+							reg = <0x2>;
+
+							asrc_in3_ep: endpoint {
+								remote-endpoint = <&xbar_asrc_in3_ep>;
+							};
+						};
+
+						port@3 {
+							reg = <0x3>;
+
+							asrc_in4_ep: endpoint {
+								remote-endpoint = <&xbar_asrc_in4_ep>;
+							};
+						};
+
+						port@4 {
+							reg = <0x4>;
+
+							asrc_in5_ep: endpoint {
+								remote-endpoint = <&xbar_asrc_in5_ep>;
+							};
+						};
+
+						port@5 {
+							reg = <0x5>;
+
+							asrc_in6_ep: endpoint {
+								remote-endpoint = <&xbar_asrc_in6_ep>;
+							};
+						};
+
+						port@6 {
+							reg = <0x6>;
+
+							asrc_in7_ep: endpoint {
+								remote-endpoint = <&xbar_asrc_in7_ep>;
+							};
+						};
+
+						asrc_out1_port: port@7 {
+							reg = <0x7>;
+
+							asrc_out1_ep: endpoint {
+								remote-endpoint = <&xbar_asrc_out1_ep>;
+							};
+						};
+
+						asrc_out2_port: port@8 {
+							reg = <0x8>;
+
+							asrc_out2_ep: endpoint {
+								remote-endpoint = <&xbar_asrc_out2_ep>;
+							};
+						};
+
+						asrc_out3_port: port@9 {
+							reg = <0x9>;
+
+							asrc_out3_ep: endpoint {
+								remote-endpoint = <&xbar_asrc_out3_ep>;
+							};
+						};
+
+						asrc_out4_port: port@a {
+							reg = <0xa>;
+
+							asrc_out4_ep: endpoint {
+								remote-endpoint = <&xbar_asrc_out4_ep>;
+							};
+						};
+
+						asrc_out5_port: port@b {
+							reg = <0xb>;
+
+							asrc_out5_ep: endpoint {
+								remote-endpoint = <&xbar_asrc_out5_ep>;
+							};
+						};
+
+						asrc_out6_port:	port@c {
+							reg = <0xc>;
+
+							asrc_out6_ep: endpoint {
+								remote-endpoint = <&xbar_asrc_out6_ep>;
+							};
+						};
+					};
+				};
 			};
 		};
 
@@ -1826,6 +2084,10 @@
 			pads {
 				usb2 {
 					lanes {
+						usb2-0 {
+							status = "okay";
+						};
+
 						usb2-1 {
 							status = "okay";
 						};
@@ -1846,6 +2108,20 @@
 			};
 
 			ports {
+				usb2-0 {
+					mode = "otg";
+					status = "okay";
+					usb-role-switch;
+					connector {
+						compatible = "gpio-usb-b-connector",
+							"usb-b-connector";
+						label = "micro-USB";
+						type = "micro";
+						vbus-gpio = <&gpio TEGRA194_MAIN_GPIO(Z, 1)
+								GPIO_ACTIVE_LOW>;
+					};
+				};
+
 				usb2-1 {
 					mode = "host";
 					status = "okay";
@@ -1874,11 +2150,18 @@
 			phy-names = "usb2-1", "usb2-2", "usb3-2";
 		};
 
+		usb@3550000 {
+			status = "okay";
+
+			phys = <&{/bus@0/padctl@3520000/pads/usb2/lanes/usb2-0}>;
+			phy-names = "usb2-0";
+		};
+
 		spi@3270000 {
 			status = "okay";
 
 			flash@0 {
-				compatible = "spi-nor";
+				compatible = "jedec,spi-nor";
 				reg = <0>;
 				spi-max-frequency = <102000000>;
 				spi-tx-bus-width = <4>;
@@ -1968,7 +2251,7 @@
 			    "p2u-5", "p2u-6", "p2u-7";
 	};
 
-	fan: fan {
+	fan: pwm-fan {
 		compatible = "pwm-fan";
 		pwms = <&pwm6 0 45334>;
 
@@ -1979,7 +2262,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		force-recovery {
+		key-force-recovery {
 			label = "Force Recovery";
 			gpios = <&gpio TEGRA194_MAIN_GPIO(G, 0)
 				       GPIO_ACTIVE_LOW>;
@@ -1988,7 +2271,7 @@
 			debounce-interval = <10>;
 		};
 
-		power {
+		key-power {
 			label = "Power";
 			gpios = <&gpio_aon TEGRA194_AON_GPIO(EE, 4)
 					   GPIO_ACTIVE_LOW>;
@@ -2000,7 +2283,7 @@
 		};
 	};
 
-	vdd_5v0_sys: regulator@100 {
+	vdd_5v0_sys: regulator-vdd-5v0-sys {
 		compatible = "regulator-fixed";
 		regulator-name = "VDD_5V_SYS";
 		regulator-min-microvolt = <5000000>;
@@ -2009,7 +2292,7 @@
 		regulator-boot-on;
 	};
 
-	vdd_3v3_sys: regulator@101 {
+	vdd_3v3_sys: regulator-vdd-3v3-sys {
 		compatible = "regulator-fixed";
 		regulator-name = "VDD_3V3_SYS";
 		regulator-min-microvolt = <3300000>;
@@ -2018,7 +2301,7 @@
 		regulator-boot-on;
 	};
 
-	vdd_3v3_ao: regulator@102 {
+	vdd_3v3_ao: regulator-vdd-3v3-ao {
 		compatible = "regulator-fixed";
 		regulator-name = "VDD_3V3_AO";
 		regulator-min-microvolt = <3300000>;
@@ -2027,7 +2310,7 @@
 		regulator-boot-on;
 	};
 
-	vdd_1v8: regulator@103 {
+	vdd_1v8: regulator-vdd-1v8 {
 		compatible = "regulator-fixed";
 		regulator-name = "VDD_1V8";
 		regulator-min-microvolt = <1800000>;
@@ -2036,7 +2319,7 @@
 		regulator-boot-on;
 	};
 
-	vdd_hdmi: regulator@104 {
+	vdd_hdmi: regulator-vdd-hdmi {
 		compatible = "regulator-fixed";
 		regulator-name = "VDD_5V0_HDMI_CON";
 		regulator-min-microvolt = <5000000>;
@@ -2077,6 +2360,11 @@
 		       <&xbar_mixer_in5_port>, <&xbar_mixer_in6_port>,
 		       <&xbar_mixer_in7_port>, <&xbar_mixer_in8_port>,
 		       <&xbar_mixer_in9_port>, <&xbar_mixer_in10_port>,
+		       <&xbar_asrc_in1_port>, <&xbar_asrc_in2_port>,
+		       <&xbar_asrc_in3_port>, <&xbar_asrc_in4_port>,
+		       <&xbar_asrc_in5_port>, <&xbar_asrc_in6_port>,
+		       <&xbar_asrc_in7_port>,
+		       <&xbar_ope1_in_port>,
 		       /* HW accelerators */
 		       <&sfc1_out_port>, <&sfc2_out_port>,
 		       <&sfc3_out_port>, <&sfc4_out_port>,
@@ -2094,6 +2382,9 @@
 		       <&mixer_out1_port>, <&mixer_out2_port>,
 		       <&mixer_out3_port>, <&mixer_out4_port>,
 		       <&mixer_out5_port>,
+		       <&asrc_out1_port>, <&asrc_out2_port>, <&asrc_out3_port>,
+		       <&asrc_out4_port>, <&asrc_out5_port>, <&asrc_out6_port>,
+		       <&ope1_out_port>,
 		       /* BE I/O Ports */
 		       <&i2s3_port>, <&i2s5_port>,
 		       <&dmic1_port>, <&dmic2_port>, <&dmic4_port>,
@@ -2103,7 +2394,7 @@
 	};
 
 	thermal-zones {
-		cpu {
+		cpu-thermal {
 			polling-delay = <0>;
 			polling-delay-passive = <500>;
 			status = "okay";
@@ -2157,7 +2448,7 @@
 			};
 		};
 
-		gpu {
+		gpu-thermal {
 			polling-delay = <0>;
 			polling-delay-passive = <500>;
 			status = "okay";
@@ -2171,7 +2462,7 @@
 			};
 		};
 
-		aux {
+		aux-thermal {
 			polling-delay = <0>;
 			polling-delay-passive = <500>;
 			status = "okay";
diff --git a/arch/arm64/boot/dts/nvidia/tegra194-p3668-0000.dtsi b/arch/arm64/boot/dts/nvidia/tegra194-p3668-0000.dtsi
index 14da4206ea66..8c2c709dd54c 100644
--- a/arch/arm64/boot/dts/nvidia/tegra194-p3668-0000.dtsi
+++ b/arch/arm64/boot/dts/nvidia/tegra194-p3668-0000.dtsi
@@ -20,7 +20,7 @@
 		};
 	};
 
-	vdd_3v3_sd: regulator@0 {
+	vdd_3v3_sd: regulator-vdd-3v3-sd {
 		compatible = "regulator-fixed";
 		regulator-name = "VDD_3V3_SD";
 		regulator-min-microvolt = <3300000>;
diff --git a/arch/arm64/boot/dts/nvidia/tegra194-p3668.dtsi b/arch/arm64/boot/dts/nvidia/tegra194-p3668.dtsi
index f16b0aa8a374..0bd66f9c620b 100644
--- a/arch/arm64/boot/dts/nvidia/tegra194-p3668.dtsi
+++ b/arch/arm64/boot/dts/nvidia/tegra194-p3668.dtsi
@@ -36,7 +36,7 @@
 				#address-cells = <1>;
 				#size-cells = <0>;
 
-				phy: phy@0 {
+				phy: ethernet-phy@0 {
 					compatible = "ethernet-phy-ieee802.3-c22";
 					reg = <0x0>;
 					interrupt-parent = <&gpio>;
diff --git a/arch/arm64/boot/dts/nvidia/tegra194.dtsi b/arch/arm64/boot/dts/nvidia/tegra194.dtsi
index 851e049b3519..41f3a7e188d0 100644
--- a/arch/arm64/boot/dts/nvidia/tegra194.dtsi
+++ b/arch/arm64/boot/dts/nvidia/tegra194.dtsi
@@ -3,6 +3,7 @@
 #include <dt-bindings/gpio/tegra194-gpio.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/mailbox/tegra186-hsp.h>
+#include <dt-bindings/pinctrl/pinctrl-tegra-io-pad.h>
 #include <dt-bindings/pinctrl/pinctrl-tegra.h>
 #include <dt-bindings/power/tegra194-powergate.h>
 #include <dt-bindings/reset/tegra194-reset.h>
@@ -22,7 +23,7 @@
 		#size-cells = <1>;
 		ranges = <0x0 0x0 0x0 0x40000000>;
 
-		misc@100000 {
+		apbmisc: misc@100000 {
 			compatible = "nvidia,tegra194-misc";
 			reg = <0x00100000 0xf000>,
 			      <0x0010f000 0x1000>;
@@ -87,6 +88,27 @@
 			gpio-controller;
 		};
 
+		cbb-noc@2300000 {
+			compatible = "nvidia,tegra194-cbb-noc";
+			reg = <0x02300000 0x1000>;
+			interrupts = <GIC_SPI 230 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 231 IRQ_TYPE_LEVEL_HIGH>;
+			nvidia,axi2apb = <&axi2apb>;
+			nvidia,apbmisc = <&apbmisc>;
+			status = "okay";
+		};
+
+		axi2apb: axi2apb@2390000 {
+			compatible = "nvidia,tegra194-axi2apb";
+			reg = <0x2390000 0x1000>,
+			      <0x23a0000 0x1000>,
+			      <0x23b0000 0x1000>,
+			      <0x23c0000 0x1000>,
+			      <0x23d0000 0x1000>,
+			      <0x23e0000 0x1000>;
+			status = "okay";
+		};
+
 		ethernet@2490000 {
 			compatible = "nvidia,tegra194-eqos",
 				     "nvidia,tegra186-eqos",
@@ -114,6 +136,49 @@
 			snps,rxpbl = <8>;
 		};
 
+		gpcdma: dma-controller@2600000 {
+			compatible = "nvidia,tegra194-gpcdma",
+				     "nvidia,tegra186-gpcdma";
+			reg = <0x2600000 0x210000>;
+			resets = <&bpmp TEGRA194_RESET_GPCDMA>;
+			reset-names = "gpcdma";
+			interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>;
+			#dma-cells = <1>;
+			iommus = <&smmu TEGRA194_SID_GPCDMA_0>;
+			dma-coherent;
+			status = "okay";
+		};
+
 		aconnect@2900000 {
 			compatible = "nvidia,tegra194-aconnect",
 				     "nvidia,tegra210-aconnect";
@@ -242,6 +307,10 @@
 						    "rx19", "tx19",
 						    "rx20", "tx20";
 					status = "disabled";
+					interconnects = <&mc TEGRA194_MEMORY_CLIENT_APEDMAR &emc>,
+							<&mc TEGRA194_MEMORY_CLIENT_APEDMAW &emc>;
+					interconnect-names = "dma-mem", "write";
+					iommus = <&smmu TEGRA194_SID_APE>;
 				};
 
 				tegra_i2s1: i2s@2901000 {
@@ -514,6 +583,29 @@
 					status = "disabled";
 				};
 
+				tegra_ope1: processing-engine@2908000 {
+					compatible = "nvidia,tegra194-ope",
+						     "nvidia,tegra210-ope";
+					reg = <0x2908000 0x100>;
+					#address-cells = <1>;
+					#size-cells = <1>;
+					ranges;
+					sound-name-prefix = "OPE1";
+					status = "disabled";
+
+					equalizer@2908100 {
+						compatible = "nvidia,tegra194-peq",
+							     "nvidia,tegra210-peq";
+						reg = <0x2908100 0x100>;
+					};
+
+					dynamic-range-compressor@2908200 {
+						compatible = "nvidia,tegra194-mbdrc",
+							     "nvidia,tegra210-mbdrc";
+						reg = <0x2908200 0x200>;
+					};
+				};
+
 				tegra_amixer: amixer@290bb00 {
 					compatible = "nvidia,tegra194-amixer",
 						     "nvidia,tegra210-amixer";
@@ -521,6 +613,14 @@
 					sound-name-prefix = "MIXER1";
 					status = "disabled";
 				};
+
+				tegra_asrc: asrc@2910000 {
+					compatible = "nvidia,tegra194-asrc",
+						     "nvidia,tegra186-asrc";
+					reg = <0x2910000 0x2000>;
+					sound-name-prefix = "ASRC1";
+					status = "disabled";
+				};
 			};
 		};
 
@@ -535,7 +635,6 @@
 				pex_rst {
 					nvidia,pins = "pex_l5_rst_n_pgg1";
 					nvidia,schmitt = <TEGRA_PIN_DISABLE>;
-					nvidia,lpdr = <TEGRA_PIN_ENABLE>;
 					nvidia,enable-input = <TEGRA_PIN_DISABLE>;
 					nvidia,io-hv = <TEGRA_PIN_ENABLE>;
 					nvidia,tristate = <TEGRA_PIN_DISABLE>;
@@ -547,7 +646,6 @@
 				clkreq {
 					nvidia,pins = "pex_l5_clkreq_n_pgg0";
 					nvidia,schmitt = <TEGRA_PIN_DISABLE>;
-					nvidia,lpdr = <TEGRA_PIN_ENABLE>;
 					nvidia,enable-input = <TEGRA_PIN_ENABLE>;
 					nvidia,io-hv = <TEGRA_PIN_ENABLE>;
 					nvidia,tristate = <TEGRA_PIN_DISABLE>;
@@ -558,9 +656,27 @@
 
 		mc: memory-controller@2c00000 {
 			compatible = "nvidia,tegra194-mc";
-			reg = <0x02c00000 0x100000>,
-			      <0x02b80000 0x040000>,
-			      <0x01700000 0x100000>;
+			reg = <0x02c00000 0x10000>,   /* MC-SID */
+			      <0x02c10000 0x10000>,   /* MC Broadcast*/
+			      <0x02c20000 0x10000>,   /* MC0 */
+			      <0x02c30000 0x10000>,   /* MC1 */
+			      <0x02c40000 0x10000>,   /* MC2 */
+			      <0x02c50000 0x10000>,   /* MC3 */
+			      <0x02b80000 0x10000>,   /* MC4 */
+			      <0x02b90000 0x10000>,   /* MC5 */
+			      <0x02ba0000 0x10000>,   /* MC6 */
+			      <0x02bb0000 0x10000>,   /* MC7 */
+			      <0x01700000 0x10000>,   /* MC8 */
+			      <0x01710000 0x10000>,   /* MC9 */
+			      <0x01720000 0x10000>,   /* MC10 */
+			      <0x01730000 0x10000>,   /* MC11 */
+			      <0x01740000 0x10000>,   /* MC12 */
+			      <0x01750000 0x10000>,   /* MC13 */
+			      <0x01760000 0x10000>,   /* MC14 */
+			      <0x01770000 0x10000>;   /* MC15 */
+			reg-names = "sid", "broadcast", "ch0", "ch1", "ch2", "ch3",
+				    "ch4", "ch5", "ch6", "ch7", "ch8", "ch9", "ch10",
+				    "ch11", "ch12", "ch13", "ch14", "ch15";
 			interrupts = <GIC_SPI 223 IRQ_TYPE_LEVEL_HIGH>;
 			#interconnect-cells = <1>;
 			status = "disabled";
@@ -593,6 +709,7 @@
 				compatible = "nvidia,tegra194-emc";
 				reg = <0x0 0x02c60000 0x0 0x90000>,
 				      <0x0 0x01780000 0x0 0x80000>;
+				interrupts = <GIC_SPI 224 IRQ_TYPE_LEVEL_HIGH>;
 				clocks = <&bpmp TEGRA194_CLK_EMC>;
 				clock-names = "emc";
 
@@ -602,6 +719,22 @@
 			};
 		};
 
+		timer@3010000 {
+			compatible = "nvidia,tegra186-timer";
+			reg = <0x03010000 0x000e0000>;
+			interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+			status = "okay";
+		};
+
 		uarta: serial@3100000 {
 			compatible = "nvidia,tegra194-uart", "nvidia,tegra20-uart";
 			reg = <0x03100000 0x40>;
@@ -672,6 +805,10 @@
 			clock-names = "div-clk";
 			resets = <&bpmp TEGRA194_RESET_I2C1>;
 			reset-names = "i2c";
+			iommus = <&smmu TEGRA194_SID_GPCDMA_0>;
+			dma-coherent;
+			dmas = <&gpcdma 21>, <&gpcdma 21>;
+			dma-names = "rx", "tx";
 			status = "disabled";
 		};
 
@@ -697,6 +834,10 @@
 			clock-names = "div-clk";
 			resets = <&bpmp TEGRA194_RESET_I2C3>;
 			reset-names = "i2c";
+			iommus = <&smmu TEGRA194_SID_GPCDMA_0>;
+			dma-coherent;
+			dmas = <&gpcdma 23>, <&gpcdma 23>;
+			dma-names = "rx", "tx";
 			status = "disabled";
 		};
 
@@ -714,6 +855,10 @@
 			pinctrl-0 = <&state_dpaux1_i2c>;
 			pinctrl-1 = <&state_dpaux1_off>;
 			pinctrl-names = "default", "idle";
+			iommus = <&smmu TEGRA194_SID_GPCDMA_0>;
+			dma-coherent;
+			dmas = <&gpcdma 26>, <&gpcdma 26>;
+			dma-names = "rx", "tx";
 			status = "disabled";
 		};
 
@@ -731,6 +876,10 @@
 			pinctrl-0 = <&state_dpaux0_i2c>;
 			pinctrl-1 = <&state_dpaux0_off>;
 			pinctrl-names = "default", "idle";
+			iommus = <&smmu TEGRA194_SID_GPCDMA_0>;
+			dma-coherent;
+			dmas = <&gpcdma 30>, <&gpcdma 30>;
+			dma-names = "rx", "tx";
 			status = "disabled";
 		};
 
@@ -748,6 +897,10 @@
 			pinctrl-0 = <&state_dpaux2_i2c>;
 			pinctrl-1 = <&state_dpaux2_off>;
 			pinctrl-names = "default", "idle";
+			iommus = <&smmu TEGRA194_SID_GPCDMA_0>;
+			dma-coherent;
+			dmas = <&gpcdma 27>, <&gpcdma 27>;
+			dma-names = "rx", "tx";
 			status = "disabled";
 		};
 
@@ -765,6 +918,10 @@
 			pinctrl-0 = <&state_dpaux3_i2c>;
 			pinctrl-1 = <&state_dpaux3_off>;
 			pinctrl-names = "default", "idle";
+			iommus = <&smmu TEGRA194_SID_GPCDMA_0>;
+			dma-coherent;
+			dmas = <&gpcdma 31>, <&gpcdma 31>;
+			dma-names = "rx", "tx";
 			status = "disabled";
 		};
 
@@ -887,12 +1044,20 @@
 			clocks = <&bpmp TEGRA194_CLK_SDMMC1>,
 				 <&bpmp TEGRA194_CLK_SDMMC_LEGACY_TM>;
 			clock-names = "sdhci", "tmclk";
+			assigned-clocks = <&bpmp TEGRA194_CLK_SDMMC1>,
+					  <&bpmp TEGRA194_CLK_PLLC4_MUXED>;
+			assigned-clock-parents =
+					  <&bpmp TEGRA194_CLK_PLLC4_MUXED>,
+					  <&bpmp TEGRA194_CLK_PLLC4_VCO_DIV2>;
 			resets = <&bpmp TEGRA194_RESET_SDMMC1>;
 			reset-names = "sdhci";
 			interconnects = <&mc TEGRA194_MEMORY_CLIENT_SDMMCRA &emc>,
 					<&mc TEGRA194_MEMORY_CLIENT_SDMMCWA &emc>;
 			interconnect-names = "dma-mem", "write";
 			iommus = <&smmu TEGRA194_SID_SDMMC1>;
+			pinctrl-names = "sdmmc-3v3", "sdmmc-1v8";
+			pinctrl-0 = <&sdmmc1_3v3>;
+			pinctrl-1 = <&sdmmc1_1v8>;
 			nvidia,pad-autocal-pull-up-offset-3v3-timeout =
 									<0x07>;
 			nvidia,pad-autocal-pull-down-offset-3v3-timeout =
@@ -904,6 +1069,10 @@
 			nvidia,pad-autocal-pull-down-offset-sdr104 = <0x00>;
 			nvidia,default-tap = <0x9>;
 			nvidia,default-trim = <0x5>;
+			sd-uhs-sdr25;
+			sd-uhs-sdr50;
+			sd-uhs-ddr50;
+			sd-uhs-sdr104;
 			status = "disabled";
 		};
 
@@ -914,12 +1083,20 @@
 			clocks = <&bpmp TEGRA194_CLK_SDMMC3>,
 				 <&bpmp TEGRA194_CLK_SDMMC_LEGACY_TM>;
 			clock-names = "sdhci", "tmclk";
+			assigned-clocks = <&bpmp TEGRA194_CLK_SDMMC3>,
+					  <&bpmp TEGRA194_CLK_PLLC4_MUXED>;
+			assigned-clock-parents =
+					  <&bpmp TEGRA194_CLK_PLLC4_MUXED>,
+					  <&bpmp TEGRA194_CLK_PLLC4_VCO_DIV2>;
 			resets = <&bpmp TEGRA194_RESET_SDMMC3>;
 			reset-names = "sdhci";
 			interconnects = <&mc TEGRA194_MEMORY_CLIENT_SDMMCR &emc>,
 					<&mc TEGRA194_MEMORY_CLIENT_SDMMCW &emc>;
 			interconnect-names = "dma-mem", "write";
 			iommus = <&smmu TEGRA194_SID_SDMMC3>;
+			pinctrl-names = "sdmmc-3v3", "sdmmc-1v8";
+			pinctrl-0 = <&sdmmc3_3v3>;
+			pinctrl-1 = <&sdmmc3_1v8>;
 			nvidia,pad-autocal-pull-up-offset-1v8 = <0x00>;
 			nvidia,pad-autocal-pull-down-offset-1v8 = <0x7a>;
 			nvidia,pad-autocal-pull-up-offset-3v3-timeout = <0x07>;
@@ -932,6 +1109,10 @@
 			nvidia,pad-autocal-pull-down-offset-sdr104 = <0x00>;
 			nvidia,default-tap = <0x9>;
 			nvidia,default-trim = <0x5>;
+			sd-uhs-sdr25;
+			sd-uhs-sdr50;
+			sd-uhs-ddr50;
+			sd-uhs-sdr104;
 			status = "disabled";
 		};
 
@@ -963,6 +1144,11 @@
 			nvidia,default-tap = <0x8>;
 			nvidia,default-trim = <0x14>;
 			nvidia,dqs-trim = <40>;
+			cap-mmc-highspeed;
+			mmc-ddr-1_8v;
+			mmc-hs200-1_8v;
+			mmc-hs400-1_8v;
+			mmc-hs400-enhanced-strobe;
 			supports-cqe;
 			status = "disabled";
 		};
@@ -976,9 +1162,8 @@
 				 <&bpmp TEGRA194_CLK_HDA2CODEC_2X>;
 			clock-names = "hda", "hda2hdmi", "hda2codec_2x";
 			resets = <&bpmp TEGRA194_RESET_HDA>,
-				 <&bpmp TEGRA194_RESET_HDA2HDMICODEC>,
-				 <&bpmp TEGRA194_RESET_HDA2CODEC_2X>;
-			reset-names = "hda", "hda2hdmi", "hda2codec_2x";
+				 <&bpmp TEGRA194_RESET_HDA2HDMICODEC>;
+			reset-names = "hda", "hda2hdmi";
 			power-domains = <&bpmp TEGRA194_POWER_DOMAIN_DISP>;
 			interconnects = <&mc TEGRA194_MEMORY_CLIENT_HDAR &emc>,
 					<&mc TEGRA194_MEMORY_CLIENT_HDAW &emc>;
@@ -1182,7 +1367,7 @@
 		};
 
 		hsp_top0: hsp@3c00000 {
-			compatible = "nvidia,tegra194-hsp", "nvidia,tegra186-hsp";
+			compatible = "nvidia,tegra194-hsp";
 			reg = <0x03c00000 0xa0000>;
 			interrupts = <GIC_SPI 176 IRQ_TYPE_LEVEL_HIGH>,
 			             <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>,
@@ -1359,8 +1544,28 @@
 			#phy-cells = <0>;
 		};
 
+		sce-noc@b600000 {
+			compatible = "nvidia,tegra194-sce-noc";
+			reg = <0xb600000 0x1000>;
+			interrupts = <GIC_SPI 261 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 173 IRQ_TYPE_LEVEL_HIGH>;
+			nvidia,axi2apb = <&axi2apb>;
+			nvidia,apbmisc = <&apbmisc>;
+			status = "okay";
+		};
+
+		rce-noc@be00000 {
+			compatible = "nvidia,tegra194-rce-noc";
+			reg = <0xbe00000 0x1000>;
+			interrupts = <GIC_SPI 259 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 175 IRQ_TYPE_LEVEL_HIGH>;
+			nvidia,axi2apb = <&axi2apb>;
+			nvidia,apbmisc = <&apbmisc>;
+			status = "okay";
+		};
+
 		hsp_aon: hsp@c150000 {
-			compatible = "nvidia,tegra194-hsp", "nvidia,tegra186-hsp";
+			compatible = "nvidia,tegra194-hsp";
 			reg = <0x0c150000 0x90000>;
 			interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>,
 			             <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>,
@@ -1384,6 +1589,10 @@
 			clock-names = "div-clk";
 			resets = <&bpmp TEGRA194_RESET_I2C2>;
 			reset-names = "i2c";
+			iommus = <&smmu TEGRA194_SID_GPCDMA_0>;
+			dma-coherent;
+			dmas = <&gpcdma 22>, <&gpcdma 22>;
+			dma-names = "rx", "tx";
 			status = "disabled";
 		};
 
@@ -1397,6 +1606,10 @@
 			clock-names = "div-clk";
 			resets = <&bpmp TEGRA194_RESET_I2C8>;
 			reset-names = "i2c";
+			iommus = <&smmu TEGRA194_SID_GPCDMA_0>;
+			dma-coherent;
+			dmas = <&gpcdma 0>, <&gpcdma 0>;
+			dma-names = "rx", "tx";
 			status = "disabled";
 		};
 
@@ -1472,6 +1685,120 @@
 
 			#interrupt-cells = <2>;
 			interrupt-controller;
+			sdmmc1_3v3: sdmmc1-3v3 {
+				pins = "sdmmc1-hv";
+				power-source = <TEGRA_IO_PAD_VOLTAGE_3V3>;
+			};
+
+			sdmmc1_1v8: sdmmc1-1v8 {
+				pins = "sdmmc1-hv";
+				power-source = <TEGRA_IO_PAD_VOLTAGE_1V8>;
+			};
+			sdmmc3_3v3: sdmmc3-3v3 {
+				pins = "sdmmc3-hv";
+				power-source = <TEGRA_IO_PAD_VOLTAGE_3V3>;
+			};
+
+			sdmmc3_1v8: sdmmc3-1v8 {
+				pins = "sdmmc3-hv";
+				power-source = <TEGRA_IO_PAD_VOLTAGE_1V8>;
+			};
+
+		};
+
+		aon-noc@c600000 {
+			compatible = "nvidia,tegra194-aon-noc";
+			reg = <0xc600000 0x1000>;
+			interrupts = <GIC_SPI 260 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 172 IRQ_TYPE_LEVEL_HIGH>;
+			nvidia,apbmisc = <&apbmisc>;
+			status = "okay";
+		};
+
+		bpmp-noc@d600000 {
+			compatible = "nvidia,tegra194-bpmp-noc";
+			reg = <0xd600000 0x1000>;
+			interrupts = <GIC_SPI 262 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>;
+			nvidia,axi2apb = <&axi2apb>;
+			nvidia,apbmisc = <&apbmisc>;
+			status = "okay";
+		};
+
+		iommu@10000000 {
+			compatible = "nvidia,tegra194-smmu", "nvidia,smmu-500";
+			reg = <0x10000000 0x800000>;
+			interrupts = <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>;
+			stream-match-mask = <0x7f80>;
+			#global-interrupts = <1>;
+			#iommu-cells = <1>;
+
+			nvidia,memory-controller = <&mc>;
+			status = "disabled";
 		};
 
 		smmu: iommu@12000000 {
@@ -1573,6 +1900,16 @@
 			interconnect-names = "dma-mem";
 			iommus = <&smmu TEGRA194_SID_HOST1X>;
 
+			/* Context isolation domains */
+			iommu-map = <0 &smmu TEGRA194_SID_HOST1X_CTX0 1>,
+				    <1 &smmu TEGRA194_SID_HOST1X_CTX1 1>,
+				    <2 &smmu TEGRA194_SID_HOST1X_CTX2 1>,
+				    <3 &smmu TEGRA194_SID_HOST1X_CTX3 1>,
+				    <4 &smmu TEGRA194_SID_HOST1X_CTX4 1>,
+				    <5 &smmu TEGRA194_SID_HOST1X_CTX5 1>,
+				    <6 &smmu TEGRA194_SID_HOST1X_CTX6 1>,
+				    <7 &smmu TEGRA194_SID_HOST1X_CTX7 1>;
+
 			nvdec@15140000 {
 				compatible = "nvidia,tegra194-nvdec";
 				reg = <0x15140000 0x00040000>;
@@ -1703,6 +2040,23 @@
 						<&mc TEGRA194_MEMORY_CLIENT_VICSWR &emc>;
 				interconnect-names = "dma-mem", "write";
 				iommus = <&smmu TEGRA194_SID_VIC>;
+				dma-coherent;
+			};
+
+			nvjpg@15380000 {
+				compatible = "nvidia,tegra194-nvjpg";
+				reg = <0x15380000 0x40000>;
+				clocks = <&bpmp TEGRA194_CLK_NVJPG>;
+				clock-names = "nvjpg";
+				resets = <&bpmp TEGRA194_RESET_NVJPG>;
+				reset-names = "nvjpg";
+
+				power-domains = <&bpmp TEGRA194_POWER_DOMAIN_NVJPG>;
+				interconnects = <&mc TEGRA194_MEMORY_CLIENT_NVJPGSRD &emc>,
+						<&mc TEGRA194_MEMORY_CLIENT_NVJPGSWR &emc>;
+				interconnect-names = "dma-mem", "write";
+				iommus = <&smmu TEGRA194_SID_NVJPG>;
+				dma-coherent;
 			};
 
 			nvdec@15480000 {
@@ -1724,6 +2078,25 @@
 				nvidia,host1x-class = <0xf0>;
 			};
 
+			nvenc@154c0000 {
+				compatible = "nvidia,tegra194-nvenc";
+				reg = <0x154c0000 0x40000>;
+				clocks = <&bpmp TEGRA194_CLK_NVENC>;
+				clock-names = "nvenc";
+				resets = <&bpmp TEGRA194_RESET_NVENC>;
+				reset-names = "nvenc";
+
+				power-domains = <&bpmp TEGRA194_POWER_DOMAIN_NVENCA>;
+				interconnects = <&mc TEGRA194_MEMORY_CLIENT_NVENCSRD &emc>,
+						<&mc TEGRA194_MEMORY_CLIENT_NVENCSRD1 &emc>,
+						<&mc TEGRA194_MEMORY_CLIENT_NVENCSWR &emc>;
+				interconnect-names = "dma-mem", "read-1", "write";
+				iommus = <&smmu TEGRA194_SID_NVENC>;
+				dma-coherent;
+
+				nvidia,host1x-class = <0x21>;
+			};
+
 			dpaux0: dpaux@155c0000 {
 				compatible = "nvidia,tegra194-dpaux";
 				reg = <0x155c0000 0x10000>;
@@ -1860,6 +2233,25 @@
 				};
 			};
 
+			nvenc@15a80000 {
+				compatible = "nvidia,tegra194-nvenc";
+				reg = <0x15a80000 0x00040000>;
+				clocks = <&bpmp TEGRA194_CLK_NVENC1>;
+				clock-names = "nvenc";
+				resets = <&bpmp TEGRA194_RESET_NVENC1>;
+				reset-names = "nvenc";
+
+				power-domains = <&bpmp TEGRA194_POWER_DOMAIN_NVENCB>;
+				interconnects = <&mc TEGRA194_MEMORY_CLIENT_NVENC1SRD &emc>,
+						<&mc TEGRA194_MEMORY_CLIENT_NVENC1SRD1 &emc>,
+						<&mc TEGRA194_MEMORY_CLIENT_NVENC1SWR &emc>;
+				interconnect-names = "dma-mem", "read-1", "write";
+				iommus = <&smmu TEGRA194_SID_NVENC1>;
+				dma-coherent;
+
+				nvidia,host1x-class = <0x22>;
+			};
+
 			sor0: sor@15b00000 {
 				compatible = "nvidia,tegra194-sor";
 				reg = <0x15b00000 0x40000>;
@@ -2007,7 +2399,6 @@
 		#size-cells = <2>;
 		device_type = "pci";
 		num-lanes = <1>;
-		num-viewport = <8>;
 		linux,pci-domain = <1>;
 
 		clocks = <&bpmp TEGRA194_CLK_PEX0_CORE_1>;
@@ -2040,7 +2431,6 @@
 		interconnects = <&mc TEGRA194_MEMORY_CLIENT_PCIE1R &emc>,
 				<&mc TEGRA194_MEMORY_CLIENT_PCIE1W &emc>;
 		interconnect-names = "dma-mem", "write";
-		iommus = <&smmu TEGRA194_SID_PCIE1>;
 		iommu-map = <0x0 &smmu TEGRA194_SID_PCIE1 0x1000>;
 		iommu-map-mask = <0x0>;
 		dma-coherent;
@@ -2061,7 +2451,6 @@
 		#size-cells = <2>;
 		device_type = "pci";
 		num-lanes = <1>;
-		num-viewport = <8>;
 		linux,pci-domain = <2>;
 
 		clocks = <&bpmp TEGRA194_CLK_PEX0_CORE_2>;
@@ -2094,7 +2483,6 @@
 		interconnects = <&mc TEGRA194_MEMORY_CLIENT_PCIE2AR &emc>,
 				<&mc TEGRA194_MEMORY_CLIENT_PCIE2AW &emc>;
 		interconnect-names = "dma-mem", "write";
-		iommus = <&smmu TEGRA194_SID_PCIE2>;
 		iommu-map = <0x0 &smmu TEGRA194_SID_PCIE2 0x1000>;
 		iommu-map-mask = <0x0>;
 		dma-coherent;
@@ -2115,7 +2503,6 @@
 		#size-cells = <2>;
 		device_type = "pci";
 		num-lanes = <1>;
-		num-viewport = <8>;
 		linux,pci-domain = <3>;
 
 		clocks = <&bpmp TEGRA194_CLK_PEX0_CORE_3>;
@@ -2148,7 +2535,6 @@
 		interconnects = <&mc TEGRA194_MEMORY_CLIENT_PCIE3R &emc>,
 				<&mc TEGRA194_MEMORY_CLIENT_PCIE3W &emc>;
 		interconnect-names = "dma-mem", "write";
-		iommus = <&smmu TEGRA194_SID_PCIE3>;
 		iommu-map = <0x0 &smmu TEGRA194_SID_PCIE3 0x1000>;
 		iommu-map-mask = <0x0>;
 		dma-coherent;
@@ -2169,7 +2555,6 @@
 		#size-cells = <2>;
 		device_type = "pci";
 		num-lanes = <4>;
-		num-viewport = <8>;
 		linux,pci-domain = <4>;
 
 		clocks = <&bpmp TEGRA194_CLK_PEX0_CORE_4>;
@@ -2202,7 +2587,6 @@
 		interconnects = <&mc TEGRA194_MEMORY_CLIENT_PCIE4R &emc>,
 				<&mc TEGRA194_MEMORY_CLIENT_PCIE4W &emc>;
 		interconnect-names = "dma-mem", "write";
-		iommus = <&smmu TEGRA194_SID_PCIE4>;
 		iommu-map = <0x0 &smmu TEGRA194_SID_PCIE4 0x1000>;
 		iommu-map-mask = <0x0>;
 		dma-coherent;
@@ -2223,7 +2607,6 @@
 		#size-cells = <2>;
 		device_type = "pci";
 		num-lanes = <8>;
-		num-viewport = <8>;
 		linux,pci-domain = <0>;
 
 		clocks = <&bpmp TEGRA194_CLK_PEX0_CORE_0>;
@@ -2256,7 +2639,6 @@
 		interconnects = <&mc TEGRA194_MEMORY_CLIENT_PCIE0R &emc>,
 				<&mc TEGRA194_MEMORY_CLIENT_PCIE0W &emc>;
 		interconnect-names = "dma-mem", "write";
-		iommus = <&smmu TEGRA194_SID_PCIE0>;
 		iommu-map = <0x0 &smmu TEGRA194_SID_PCIE0 0x1000>;
 		iommu-map-mask = <0x0>;
 		dma-coherent;
@@ -2277,15 +2659,13 @@
 		#size-cells = <2>;
 		device_type = "pci";
 		num-lanes = <8>;
-		num-viewport = <8>;
 		linux,pci-domain = <5>;
 
 		pinctrl-names = "default";
 		pinctrl-0 = <&pex_rst_c5_out_state>, <&clkreq_c5_bi_dir_state>;
 
-		clocks = <&bpmp TEGRA194_CLK_PEX1_CORE_5>,
-			 <&bpmp TEGRA194_CLK_PEX1_CORE_5M>;
-		clock-names = "core", "core_m";
+		clocks = <&bpmp TEGRA194_CLK_PEX1_CORE_5>;
+		clock-names = "core";
 
 		resets = <&bpmp TEGRA194_RESET_PEX1_CORE_5_APB>,
 			 <&bpmp TEGRA194_RESET_PEX1_CORE_5>;
@@ -2314,7 +2694,6 @@
 		interconnects = <&mc TEGRA194_MEMORY_CLIENT_PCIE5R &emc>,
 				<&mc TEGRA194_MEMORY_CLIENT_PCIE5W &emc>;
 		interconnect-names = "dma-mem", "write";
-		iommus = <&smmu TEGRA194_SID_PCIE5>;
 		iommu-map = <0x0 &smmu TEGRA194_SID_PCIE5 0x1000>;
 		iommu-map-mask = <0x0>;
 		dma-coherent;
@@ -2354,7 +2733,6 @@
 		interconnects = <&mc TEGRA194_MEMORY_CLIENT_PCIE4R &emc>,
 				<&mc TEGRA194_MEMORY_CLIENT_PCIE4W &emc>;
 		interconnect-names = "dma-mem", "write";
-		iommus = <&smmu TEGRA194_SID_PCIE4>;
 		iommu-map = <0x0 &smmu TEGRA194_SID_PCIE4 0x1000>;
 		iommu-map-mask = <0x0>;
 		dma-coherent;
@@ -2394,7 +2772,6 @@
 		interconnects = <&mc TEGRA194_MEMORY_CLIENT_PCIE0R &emc>,
 				<&mc TEGRA194_MEMORY_CLIENT_PCIE0W &emc>;
 		interconnect-names = "dma-mem", "write";
-		iommus = <&smmu TEGRA194_SID_PCIE0>;
 		iommu-map = <0x0 &smmu TEGRA194_SID_PCIE0 0x1000>;
 		iommu-map-mask = <0x0>;
 		dma-coherent;
@@ -2437,7 +2814,6 @@
 		interconnects = <&mc TEGRA194_MEMORY_CLIENT_PCIE5R &emc>,
 				<&mc TEGRA194_MEMORY_CLIENT_PCIE5W &emc>;
 		interconnect-names = "dma-mem", "write";
-		iommus = <&smmu TEGRA194_SID_PCIE5>;
 		iommu-map = <0x0 &smmu TEGRA194_SID_PCIE5 0x1000>;
 		iommu-map-mask = <0x0>;
 		dma-coherent;
@@ -2449,6 +2825,7 @@
 		#address-cells = <1>;
 		#size-cells = <1>;
 		ranges = <0x0 0x0 0x40000000 0x50000>;
+		no-memory-wc;
 
 		cpu_bpmp_tx: sram@4e000 {
 			reg = <0x4e000 0x1000>;
@@ -2467,7 +2844,7 @@
 		compatible = "nvidia,tegra186-bpmp";
 		mboxes = <&hsp_top0 TEGRA_HSP_MBOX_TYPE_DB
 				    TEGRA_HSP_DB_MASTER_BPMP>;
-		shmem = <&cpu_bpmp_tx &cpu_bpmp_rx>;
+		shmem = <&cpu_bpmp_tx>, <&cpu_bpmp_rx>;
 		#clock-cells = <1>;
 		#reset-cells = <1>;
 		#power-domain-cells = <1>;
@@ -2687,7 +3064,7 @@
 	};
 
 	pmu {
-		compatible = "arm,armv8-pmuv3";
+		compatible = "nvidia,carmel-pmu";
 		interrupts = <GIC_SPI 384 IRQ_TYPE_LEVEL_HIGH>,
 			     <GIC_SPI 385 IRQ_TYPE_LEVEL_HIGH>,
 			     <GIC_SPI 386 IRQ_TYPE_LEVEL_HIGH>,
@@ -2724,14 +3101,9 @@
 		 * for 8x and 11.025x sample rate streams.
 		 */
 		assigned-clock-rates = <258000000>;
-
-		interconnects = <&mc TEGRA194_MEMORY_CLIENT_APEDMAR &emc>,
-				<&mc TEGRA194_MEMORY_CLIENT_APEDMAW &emc>;
-		interconnect-names = "dma-mem", "write";
-		iommus = <&smmu TEGRA194_SID_APE>;
 	};
 
-	tcu: tcu {
+	tcu: serial {
 		compatible = "nvidia,tegra194-tcu";
 		mboxes = <&hsp_top0 TEGRA_HSP_MBOX_TYPE_SM TEGRA_HSP_SM_RX(0)>,
 		         <&hsp_aon TEGRA_HSP_MBOX_TYPE_SM TEGRA_HSP_SM_TX(1)>;
@@ -2739,39 +3111,33 @@
 	};
 
 	thermal-zones {
-		cpu {
-			thermal-sensors = <&{/bpmp/thermal}
-					   TEGRA194_BPMP_THERMAL_ZONE_CPU>;
+		cpu-thermal {
+			thermal-sensors = <&{/bpmp/thermal} TEGRA194_BPMP_THERMAL_ZONE_CPU>;
 			status = "disabled";
 		};
 
-		gpu {
-			thermal-sensors = <&{/bpmp/thermal}
-					   TEGRA194_BPMP_THERMAL_ZONE_GPU>;
+		gpu-thermal {
+			thermal-sensors = <&{/bpmp/thermal} TEGRA194_BPMP_THERMAL_ZONE_GPU>;
 			status = "disabled";
 		};
 
-		aux {
-			thermal-sensors = <&{/bpmp/thermal}
-					   TEGRA194_BPMP_THERMAL_ZONE_AUX>;
+		aux-thermal {
+			thermal-sensors = <&{/bpmp/thermal} TEGRA194_BPMP_THERMAL_ZONE_AUX>;
 			status = "disabled";
 		};
 
-		pllx {
-			thermal-sensors = <&{/bpmp/thermal}
-					   TEGRA194_BPMP_THERMAL_ZONE_PLLX>;
+		pllx-thermal {
+			thermal-sensors = <&{/bpmp/thermal} TEGRA194_BPMP_THERMAL_ZONE_PLLX>;
 			status = "disabled";
 		};
 
-		ao {
-			thermal-sensors = <&{/bpmp/thermal}
-					   TEGRA194_BPMP_THERMAL_ZONE_AO>;
+		ao-thermal {
+			thermal-sensors = <&{/bpmp/thermal} TEGRA194_BPMP_THERMAL_ZONE_AO>;
 			status = "disabled";
 		};
 
-		tj {
-			thermal-sensors = <&{/bpmp/thermal}
-					   TEGRA194_BPMP_THERMAL_ZONE_TJ_MAX>;
+		tj-thermal {
+			thermal-sensors = <&{/bpmp/thermal} TEGRA194_BPMP_THERMAL_ZONE_TJ_MAX>;
 			status = "disabled";
 		};
 	};
diff --git a/arch/arm64/boot/dts/nvidia/tegra210-p2180.dtsi b/arch/arm64/boot/dts/nvidia/tegra210-p2180.dtsi
index 6077d572d828..75eb743a7242 100644
--- a/arch/arm64/boot/dts/nvidia/tegra210-p2180.dtsi
+++ b/arch/arm64/boot/dts/nvidia/tegra210-p2180.dtsi
@@ -301,7 +301,7 @@
 		vqmmc-supply = <&vdd_1v8>;
 	};
 
-	clk32k_in: clock@0 {
+	clk32k_in: clock-32k {
 		compatible = "fixed-clock";
 		clock-frequency = <32768>;
 		#clock-cells = <0>;
@@ -336,7 +336,7 @@
 		method = "smc";
 	};
 
-	vdd_gpu: regulator@100 {
+	vdd_gpu: regulator-vdd-gpu {
 		compatible = "pwm-regulator";
 		pwms = <&pwm 1 8000>;
 		regulator-name = "VDD_GPU";
diff --git a/arch/arm64/boot/dts/nvidia/tegra210-p2371-2180.dts b/arch/arm64/boot/dts/nvidia/tegra210-p2371-2180.dts
index 2e17df6f20ad..1e26ca91a944 100644
--- a/arch/arm64/boot/dts/nvidia/tegra210-p2371-2180.dts
+++ b/arch/arm64/boot/dts/nvidia/tegra210-p2371-2180.dts
@@ -11,11 +11,8 @@
 	pcie@1003000 {
 		status = "okay";
 
-		avdd-pll-uerefe-supply = <&avdd_1v05_pll>;
 		hvddio-pex-supply = <&vdd_1v8>;
 		dvddio-pex-supply = <&vdd_pex_1v05>;
-		dvdd-pex-pll-supply = <&vdd_pex_1v05>;
-		hvdd-pex-pll-e-supply = <&vdd_1v8>;
 		vddio-pex-ctl-supply = <&vdd_1v8>;
 
 		pci@1,0 {
@@ -685,6 +682,56 @@
 				};
 			};
 
+			processing-engine@702d8000 {
+				status = "okay";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0x0>;
+
+						ope1_cif_in_ep: endpoint {
+							remote-endpoint = <&xbar_ope1_in_ep>;
+						};
+					};
+
+					ope1_out_port: port@1 {
+						reg = <0x1>;
+
+						ope1_cif_out_ep: endpoint {
+							remote-endpoint = <&xbar_ope1_out_ep>;
+						};
+					};
+				};
+			};
+
+			processing-engine@702d8400 {
+				status = "okay";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0x0>;
+
+						ope2_cif_in_ep: endpoint {
+							remote-endpoint = <&xbar_ope2_in_ep>;
+						};
+					};
+
+					ope2_out_port: port@1 {
+						reg = <0x1>;
+
+						ope2_cif_out_ep: endpoint {
+							remote-endpoint = <&xbar_ope2_out_ep>;
+						};
+					};
+				};
+			};
+
 			amixer@702dbb00 {
 				status = "okay";
 
@@ -1254,6 +1301,38 @@
 						remote-endpoint = <&mixer_out5_ep>;
 					};
 				};
+
+				xbar_ope1_in_port: port@41 {
+					reg = <0x41>;
+
+					xbar_ope1_in_ep: endpoint {
+						remote-endpoint = <&ope1_cif_in_ep>;
+					};
+				};
+
+				port@42 {
+					reg = <0x42>;
+
+					xbar_ope1_out_ep: endpoint {
+						remote-endpoint = <&ope1_cif_out_ep>;
+					};
+				};
+
+				xbar_ope2_in_port: port@43 {
+					reg = <0x43>;
+
+					xbar_ope2_in_ep: endpoint {
+						remote-endpoint = <&ope2_cif_in_ep>;
+					};
+				};
+
+				port@44 {
+					reg = <0x44>;
+
+					xbar_ope2_out_ep: endpoint {
+						remote-endpoint = <&ope2_cif_out_ep>;
+					};
+				};
 			};
 		};
 	};
@@ -1284,6 +1363,7 @@
 		       <&xbar_mixer_in5_port>, <&xbar_mixer_in6_port>,
 		       <&xbar_mixer_in7_port>, <&xbar_mixer_in8_port>,
 		       <&xbar_mixer_in9_port>, <&xbar_mixer_in10_port>,
+		       <&xbar_ope1_in_port>, <&xbar_ope2_in_port>,
 		       /* HW accelerators */
 		       <&sfc1_out_port>, <&sfc2_out_port>,
 		       <&sfc3_out_port>, <&sfc4_out_port>,
@@ -1296,6 +1376,7 @@
 		       <&mixer_out1_port>, <&mixer_out2_port>,
 		       <&mixer_out3_port>, <&mixer_out4_port>,
 		       <&mixer_out5_port>,
+		       <&ope1_out_port>, <&ope2_out_port>,
 		       /* I/O DAP Ports */
 		       <&i2s1_port>, <&i2s2_port>, <&i2s3_port>, <&i2s4_port>,
 		       <&i2s5_port>, <&dmic1_port>, <&dmic2_port>, <&dmic3_port>;
diff --git a/arch/arm64/boot/dts/nvidia/tegra210-p2530.dtsi b/arch/arm64/boot/dts/nvidia/tegra210-p2530.dtsi
index 58aa0518965e..0a70daeffd85 100644
--- a/arch/arm64/boot/dts/nvidia/tegra210-p2530.dtsi
+++ b/arch/arm64/boot/dts/nvidia/tegra210-p2530.dtsi
@@ -40,7 +40,7 @@
 		non-removable;
 	};
 
-	clk32k_in: clock@0 {
+	clk32k_in: clock-32k {
 		compatible = "fixed-clock";
 		clock-frequency = <32768>;
 		#clock-cells = <0>;
diff --git a/arch/arm64/boot/dts/nvidia/tegra210-p2597.dtsi b/arch/arm64/boot/dts/nvidia/tegra210-p2597.dtsi
index d8409c1b4380..a44c56c1e56e 100644
--- a/arch/arm64/boot/dts/nvidia/tegra210-p2597.dtsi
+++ b/arch/arm64/boot/dts/nvidia/tegra210-p2597.dtsi
@@ -1361,11 +1361,6 @@
 		dvddio-pex-supply = <&vdd_pex_1v05>;
 		hvddio-pex-supply = <&vdd_1v8>;
 		avdd-usb-supply = <&vdd_3v3_sys>;
-		/* XXX what are these? */
-		avdd-pll-utmip-supply = <&vdd_1v8>;
-		avdd-pll-uerefe-supply = <&vdd_pex_1v05>;
-		dvdd-usb-ss-pll-supply = <&vdd_pex_1v05>;
-		hvdd-usb-ss-pll-e-supply = <&vdd_1v8>;
 
 		status = "okay";
 
@@ -1535,27 +1530,27 @@
 		compatible = "gpio-keys";
 		label = "gpio-keys";
 
-		power {
+		key-power {
 			label = "Power";
 			gpios = <&gpio TEGRA_GPIO(X, 5) GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
 			wakeup-source;
 		};
 
-		volume_down {
+		key-volume-down {
 			label = "Volume Down";
 			gpios = <&gpio TEGRA_GPIO(Y, 0) GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_VOLUMEDOWN>;
 		};
 
-		volume_up {
+		key-volume-up {
 			label = "Volume Up";
 			gpios = <&gpio TEGRA_GPIO(X, 6) GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_VOLUMEUP>;
 		};
 	};
 
-	vdd_sys_mux: regulator@0 {
+	vdd_sys_mux: regulator-vdd-sys-mux {
 		compatible = "regulator-fixed";
 		regulator-name = "VDD_SYS_MUX";
 		regulator-min-microvolt = <5000000>;
@@ -1564,7 +1559,7 @@
 		regulator-boot-on;
 	};
 
-	vdd_5v0_sys: regulator@1 {
+	vdd_5v0_sys: regulator-vdd-5v0-sys {
 		compatible = "regulator-fixed";
 		regulator-name = "VDD_5V0_SYS";
 		regulator-min-microvolt = <5000000>;
@@ -1576,7 +1571,7 @@
 		vin-supply = <&vdd_sys_mux>;
 	};
 
-	vdd_3v3_sys: regulator@2 {
+	vdd_3v3_sys: regulator-vdd-3v3-sys {
 		compatible = "regulator-fixed";
 		regulator-name = "VDD_3V3_SYS";
 		regulator-min-microvolt = <3300000>;
@@ -1588,10 +1583,9 @@
 		vin-supply = <&vdd_sys_mux>;
 
 		regulator-enable-ramp-delay = <160>;
-		regulator-disable-ramp-delay = <10000>;
 	};
 
-	vdd_5v0_io: regulator@3 {
+	vdd_5v0_io: regulator-vdd-5v0-io {
 		compatible = "regulator-fixed";
 		regulator-name = "VDD_5V0_IO_SYS";
 		regulator-min-microvolt = <5000000>;
@@ -1600,7 +1594,7 @@
 		regulator-boot-on;
 	};
 
-	vdd_3v3_sd: regulator@4 {
+	vdd_3v3_sd: regulator-vdd-3v3-sd {
 		compatible = "regulator-fixed";
 		regulator-name = "VDD_3V3_SD";
 		regulator-min-microvolt = <3300000>;
@@ -1610,10 +1604,9 @@
 		vin-supply = <&vdd_3v3_sys>;
 
 		regulator-enable-ramp-delay = <472>;
-		regulator-disable-ramp-delay = <4880>;
 	};
 
-	vdd_dsi_csi: regulator@5 {
+	vdd_dsi_csi: regulator-vdd-dsi-csi {
 		compatible = "regulator-fixed";
 		regulator-name = "AVDD_DSI_CSI_1V2";
 		regulator-min-microvolt = <1200000>;
@@ -1621,7 +1614,7 @@
 		vin-supply = <&vdd_sys_1v2>;
 	};
 
-	vdd_3v3_dis: regulator@6 {
+	vdd_3v3_dis: regulator-vdd-3v3-dis {
 		compatible = "regulator-fixed";
 		regulator-name = "VDD_DIS_3V3_LCD";
 		regulator-min-microvolt = <3300000>;
@@ -1632,7 +1625,7 @@
 		vin-supply = <&vdd_3v3_sys>;
 	};
 
-	vdd_1v8_dis: regulator@7 {
+	vdd_1v8_dis: regulator-vdd-1v8-dis {
 		compatible = "regulator-fixed";
 		regulator-name = "VDD_LCD_1V8_DIS";
 		regulator-min-microvolt = <1800000>;
@@ -1643,7 +1636,7 @@
 		vin-supply = <&vdd_1v8>;
 	};
 
-	vdd_5v0_rtl: regulator@8 {
+	vdd_5v0_rtl: regulator-vdd-5v0-rtl {
 		compatible = "regulator-fixed";
 		regulator-name = "RTL_5V";
 		regulator-min-microvolt = <5000000>;
@@ -1653,7 +1646,7 @@
 		vin-supply = <&vdd_5v0_sys>;
 	};
 
-	vdd_usb_vbus: regulator@9 {
+	vdd_usb_vbus: regulator-vdd-usb-vbus {
 		compatible = "regulator-fixed";
 		regulator-name = "USB_VBUS_EN1";
 		regulator-min-microvolt = <5000000>;
@@ -1663,7 +1656,7 @@
 		vin-supply = <&vdd_5v0_sys>;
 	};
 
-	vdd_hdmi: regulator@10 {
+	vdd_hdmi: regulator-vdd-hdmi {
 		compatible = "regulator-fixed";
 		regulator-name = "VDD_HDMI_5V0";
 		regulator-min-microvolt = <5000000>;
@@ -1673,7 +1666,7 @@
 		vin-supply = <&vdd_5v0_sys>;
 	};
 
-	vdd_cam_1v2: regulator@11 {
+	vdd_cam_1v2: regulator-vdd-cam-1v8 {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd-cam-1v2";
 		regulator-min-microvolt = <1200000>;
@@ -1683,7 +1676,7 @@
 		vin-supply = <&vdd_3v3_sys>;
 	};
 
-	vdd_cam_2v8: regulator@12 {
+	vdd_cam_2v8: regulator-vdd-cam-2v8 {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd-cam-2v8";
 		regulator-min-microvolt = <2800000>;
@@ -1693,7 +1686,7 @@
 		vin-supply = <&vdd_3v3_sys>;
 	};
 
-	vdd_cam_1v8: regulator@13 {
+	vdd_cam_1v8: regulator-vdd-cam-1v8 {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd-cam-1v8";
 		regulator-min-microvolt = <1800000>;
@@ -1703,7 +1696,7 @@
 		vin-supply = <&vdd_3v3_sys>;
 	};
 
-	vdd_usb_vbus_otg: regulator@14 {
+	vdd_usb_vbus_otg: regulator-vdd-usb-vbus-otg {
 		compatible = "regulator-fixed";
 		regulator-name = "USB_VBUS_EN0";
 		regulator-min-microvolt = <5000000>;
diff --git a/arch/arm64/boot/dts/nvidia/tegra210-p2894.dtsi b/arch/arm64/boot/dts/nvidia/tegra210-p2894.dtsi
index 41beab626d95..8e657b10569d 100644
--- a/arch/arm64/boot/dts/nvidia/tegra210-p2894.dtsi
+++ b/arch/arm64/boot/dts/nvidia/tegra210-p2894.dtsi
@@ -1383,7 +1383,7 @@
 				};
 			};
 
-			gpio@0 {
+			hog-0 {
 				gpio-hog;
 				output-high;
 				gpios = <2 GPIO_ACTIVE_HIGH>,
@@ -1586,7 +1586,7 @@
 		status = "okay";
 	};
 
-	clk32k_in: clock@0 {
+	clk32k_in: clock-32k {
 		compatible = "fixed-clock";
 		clock-frequency = <32768>;
 		#clock-cells = <0>;
@@ -1596,7 +1596,7 @@
 		compatible = "gpio-keys";
 		status = "okay";
 
-		power {
+		key-power {
 			debounce-interval = <30>;
 			gpios = <&gpio TEGRA_GPIO(X, 7) GPIO_ACTIVE_LOW>;
 			label = "Power";
@@ -1635,7 +1635,7 @@
 		method = "smc";
 	};
 
-	battery_reg: regulator@0 {
+	battery_reg: regulator-vdd-ac-bat {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd-ac-bat";
 		regulator-min-microvolt = <5000000>;
@@ -1643,7 +1643,7 @@
 		regulator-always-on;
 	};
 
-	vdd_3v3: regulator@1 {
+	vdd_3v3: regulator-vdd-3v3 {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd-3v3";
 		regulator-enable-ramp-delay = <160>;
@@ -1655,7 +1655,7 @@
 		enable-active-high;
 	};
 
-	max77620_gpio7: regulator@2 {
+	max77620_gpio7: regulator-max77620-gpio7 {
 		compatible = "regulator-fixed";
 		regulator-name = "max77620-gpio7";
 		regulator-enable-ramp-delay = <240>;
@@ -1669,7 +1669,7 @@
 		enable-active-high;
 	};
 
-	lcd_bl_en: regulator@3 {
+	lcd_bl_en: regulator-lcd-bl-en {
 		compatible = "regulator-fixed";
 		regulator-name = "lcd-bl-en";
 		regulator-min-microvolt = <1800000>;
@@ -1680,7 +1680,7 @@
 		enable-active-high;
 	};
 
-	en_vdd_sd: regulator@4 {
+	en_vdd_sd: regulator-vdd-sd {
 		compatible = "regulator-fixed";
 		regulator-name = "en-vdd-sd";
 		regulator-enable-ramp-delay = <472>;
@@ -1692,7 +1692,7 @@
 		enable-active-high;
 	};
 
-	en_vdd_cam: regulator@5 {
+	en_vdd_cam: regulator-vdd-cam {
 		compatible = "regulator-fixed";
 		regulator-name = "en-vdd-cam";
 		regulator-min-microvolt = <1800000>;
@@ -1702,7 +1702,7 @@
 		enable-active-high;
 	};
 
-	vdd_sys_boost: regulator@6 {
+	vdd_sys_boost: regulator-vdd-sys-boost {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd-sys-boost";
 		regulator-enable-ramp-delay = <3090>;
@@ -1714,7 +1714,7 @@
 		enable-active-high;
 	};
 
-	vdd_hdmi: regulator@7 {
+	vdd_hdmi: regulator-vdd-hdmi {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd-hdmi";
 		regulator-enable-ramp-delay = <468>;
@@ -1727,21 +1727,21 @@
 		enable-active-high;
 	};
 
-	en_vdd_cpu_fixed: regulator@8 {
+	en_vdd_cpu_fixed: regulator-vdd-cpu-fixed {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd-cpu-fixed";
 		regulator-min-microvolt = <1000000>;
 		regulator-max-microvolt = <1000000>;
 	};
 
-	vdd_aux_3v3: regulator@9 {
+	vdd_aux_3v3: regulator-vdd-aux-3v3 {
 		compatible = "regulator-fixed";
 		regulator-name = "aux-3v3";
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
 	};
 
-	vdd_snsr_pm: regulator@10 {
+	vdd_snsr_pm: regulator-vdd-snsr-pm {
 		compatible = "regulator-fixed";
 		regulator-name = "snsr_pm";
 		regulator-min-microvolt = <3300000>;
@@ -1750,7 +1750,7 @@
 		enable-active-high;
 	};
 
-	vdd_usb_5v0: regulator@11 {
+	vdd_usb_5v0: regulator-vdd-usb-5v0 {
 		compatible = "regulator-fixed";
 		status = "disabled";
 		regulator-name = "vdd-usb-5v0";
@@ -1761,7 +1761,7 @@
 		enable-active-high;
 	};
 
-	vdd_cdc_1v2_aud: regulator@101 {
+	vdd_cdc_1v2_aud: regulator-vdd-cdc-1v2-aud {
 		compatible = "regulator-fixed";
 		status = "disabled";
 		regulator-name = "vdd_cdc_1v2_aud";
@@ -1772,7 +1772,7 @@
 		enable-active-high;
 	};
 
-	vdd_disp_3v0: regulator@12 {
+	vdd_disp_3v0: regulator-vdd-disp-3v0 {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd-disp-3v0";
 		regulator-enable-ramp-delay = <232>;
@@ -1784,7 +1784,7 @@
 		enable-active-high;
 	};
 
-	vdd_fan: regulator@13 {
+	vdd_fan: regulator-vdd-fan {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd-fan";
 		regulator-enable-ramp-delay = <284>;
@@ -1795,7 +1795,7 @@
 		enable-active-high;
 	};
 
-	usb_vbus1: regulator@14 {
+	usb_vbus1: regulator-usb-vbus1 {
 		compatible = "regulator-fixed";
 		regulator-name = "usb-vbus1";
 		regulator-min-microvolt = <5000000>;
@@ -1806,7 +1806,7 @@
 		gpio-open-drain;
 	};
 
-	usb_vbus2: regulator@15 {
+	usb_vbus2: regulator-usb-vbus2 {
 		compatible = "regulator-fixed";
 		regulator-name = "usb-vbus2";
 		regulator-min-microvolt = <5000000>;
@@ -1817,7 +1817,7 @@
 		gpio-open-drain;
 	};
 
-	vdd_3v3_eth: regulator@16 {
+	vdd_3v3_eth: regulator-vdd-3v3-eth {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd-3v3-eth-a02";
 		regulator-min-microvolt = <3300000>;
diff --git a/arch/arm64/boot/dts/nvidia/tegra210-p3450-0000.dts b/arch/arm64/boot/dts/nvidia/tegra210-p3450-0000.dts
index 030f264eccd5..37678c337a34 100644
--- a/arch/arm64/boot/dts/nvidia/tegra210-p3450-0000.dts
+++ b/arch/arm64/boot/dts/nvidia/tegra210-p3450-0000.dts
@@ -30,11 +30,8 @@
 	pcie@1003000 {
 		status = "okay";
 
-		avdd-pll-uerefe-supply = <&vdd_pex_1v05>;
 		hvddio-pex-supply = <&vdd_1v8>;
 		dvddio-pex-supply = <&vdd_pex_1v05>;
-		dvdd-pex-pll-supply = <&vdd_pex_1v05>;
-		hvdd-pex-pll-e-supply = <&vdd_1v8>;
 		vddio-pex-ctl-supply = <&vdd_1v8>;
 
 		pci@1,0 {
@@ -266,7 +263,6 @@
 					regulator-min-microvolt = <1000000>;
 					regulator-max-microvolt = <1170000>;
 					regulator-enable-ramp-delay = <146>;
-					regulator-disable-ramp-delay = <4080>;
 					regulator-ramp-delay = <27500>;
 					regulator-ramp-delay-scale = <300>;
 					regulator-always-on;
@@ -282,7 +278,6 @@
 					regulator-min-microvolt = <1150000>;
 					regulator-max-microvolt = <1150000>;
 					regulator-enable-ramp-delay = <176>;
-					regulator-disable-ramp-delay = <145800>;
 					regulator-ramp-delay = <27500>;
 					regulator-ramp-delay-scale = <300>;
 					regulator-always-on;
@@ -298,7 +293,6 @@
 					regulator-min-microvolt = <1350000>;
 					regulator-max-microvolt = <1350000>;
 					regulator-enable-ramp-delay = <176>;
-					regulator-disable-ramp-delay = <32000>;
 					regulator-ramp-delay = <27500>;
 					regulator-ramp-delay-scale = <350>;
 					regulator-always-on;
@@ -314,7 +308,6 @@
 					regulator-min-microvolt = <1800000>;
 					regulator-max-microvolt = <1800000>;
 					regulator-enable-ramp-delay = <242>;
-					regulator-disable-ramp-delay = <118000>;
 					regulator-ramp-delay = <27500>;
 					regulator-ramp-delay-scale = <360>;
 					regulator-always-on;
@@ -330,7 +323,6 @@
 					regulator-min-microvolt = <1200000>;
 					regulator-max-microvolt = <1200000>;
 					regulator-enable-ramp-delay = <26>;
-					regulator-disable-ramp-delay = <626>;
 					regulator-ramp-delay = <100000>;
 					regulator-ramp-delay-scale = <200>;
 					regulator-always-on;
@@ -346,7 +338,6 @@
 					regulator-min-microvolt = <1050000>;
 					regulator-max-microvolt = <1050000>;
 					regulator-enable-ramp-delay = <22>;
-					regulator-disable-ramp-delay = <650>;
 					regulator-ramp-delay = <100000>;
 					regulator-ramp-delay-scale = <200>;
 
@@ -360,7 +351,6 @@
 					regulator-min-microvolt = <1800000>;
 					regulator-max-microvolt = <3300000>;
 					regulator-enable-ramp-delay = <62>;
-					regulator-disable-ramp-delay = <650>;
 					regulator-ramp-delay = <100000>;
 					regulator-ramp-delay-scale = <200>;
 
@@ -378,7 +368,6 @@
 					regulator-min-microvolt = <850000>;
 					regulator-max-microvolt = <1100000>;
 					regulator-enable-ramp-delay = <22>;
-					regulator-disable-ramp-delay = <610>;
 					regulator-ramp-delay = <100000>;
 					regulator-ramp-delay-scale = <200>;
 					regulator-disable-active-discharge;
@@ -403,7 +392,6 @@
 					regulator-min-microvolt = <1050000>;
 					regulator-max-microvolt = <1050000>;
 					regulator-enable-ramp-delay = <24>;
-					regulator-disable-ramp-delay = <2768>;
 					regulator-ramp-delay = <100000>;
 					regulator-ramp-delay-scale = <200>;
 
@@ -417,7 +405,6 @@
 					regulator-min-microvolt = <1050000>;
 					regulator-max-microvolt = <1050000>;
 					regulator-enable-ramp-delay = <22>;
-					regulator-disable-ramp-delay = <1160>;
 					regulator-ramp-delay = <100000>;
 					regulator-ramp-delay-scale = <200>;
 
@@ -456,11 +443,6 @@
 		avdd-usb-supply = <&vdd_3v3_sys>;
 		dvddio-pex-supply = <&vdd_pex_1v05>;
 		hvddio-pex-supply = <&vdd_1v8>;
-		/* these really belong to the XUSB pad controller */
-		avdd-pll-utmip-supply = <&vdd_1v8>;
-		avdd-pll-uerefe-supply = <&vdd_pex_1v05>;
-		dvdd-usb-ss-pll-supply = <&vdd_pex_1v05>;
-		hvdd-usb-ss-pll-e-supply = <&vdd_1v8>;
 
 		status = "okay";
 	};
@@ -688,7 +670,7 @@
 					i2s4_port: port@1 {
 						reg = <1>;
 
-						i2s4_dap_ep: endpoint@0 {
+						i2s4_dap_ep: endpoint {
 							dai-format = "i2s";
 							/* Placeholder for external Codec */
 						};
@@ -706,7 +688,7 @@
 					port@0 {
 						reg = <0>;
 
-						dmic1_cif_ep: endpoint@0 {
+						dmic1_cif_ep: endpoint {
 							remote-endpoint = <&xbar_dmic1_ep>;
 						};
 					};
@@ -714,7 +696,7 @@
 					dmic1_port: port@1 {
 						reg = <1>;
 
-						dmic1_dap_ep: endpoint@0 {
+						dmic1_dap_ep: endpoint {
 							/* Placeholder for external Codec */
 						};
 					};
@@ -731,7 +713,7 @@
 					port@0 {
 						reg = <0>;
 
-						dmic2_cif_ep: endpoint@0 {
+						dmic2_cif_ep: endpoint {
 							remote-endpoint = <&xbar_dmic2_ep>;
 						};
 					};
@@ -739,7 +721,7 @@
 					dmic2_port: port@1 {
 						reg = <1>;
 
-						dmic2_dap_ep: endpoint@0 {
+						dmic2_dap_ep: endpoint {
 							/* Placeholder for external Codec */
 						};
 					};
@@ -1092,6 +1074,56 @@
 				};
 			};
 
+			processing-engine@702d8000 {
+				status = "okay";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0x0>;
+
+						ope1_cif_in_ep: endpoint {
+							remote-endpoint = <&xbar_ope1_in_ep>;
+						};
+					};
+
+					ope1_out_port: port@1 {
+						reg = <0x1>;
+
+						ope1_cif_out_ep: endpoint {
+							remote-endpoint = <&xbar_ope1_out_ep>;
+						};
+					};
+				};
+			};
+
+			processing-engine@702d8400 {
+				status = "okay";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0x0>;
+
+						ope2_cif_in_ep: endpoint {
+							remote-endpoint = <&xbar_ope2_in_ep>;
+						};
+					};
+
+					ope2_out_port: port@1 {
+						reg = <0x1>;
+
+						ope2_cif_out_ep: endpoint {
+							remote-endpoint = <&xbar_ope2_out_ep>;
+						};
+					};
+				};
+			};
+
 			amixer@702dbb00 {
 				status = "okay";
 
@@ -1629,6 +1661,38 @@
 						remote-endpoint = <&mixer_out5_ep>;
 					};
 				};
+
+				xbar_ope1_in_port: port@41 {
+					reg = <0x41>;
+
+					xbar_ope1_in_ep: endpoint {
+						remote-endpoint = <&ope1_cif_in_ep>;
+					};
+				};
+
+				port@42 {
+					reg = <0x42>;
+
+					xbar_ope1_out_ep: endpoint {
+						remote-endpoint = <&ope1_cif_out_ep>;
+					};
+				};
+
+				xbar_ope2_in_port: port@43 {
+					reg = <0x43>;
+
+					xbar_ope2_in_ep: endpoint {
+						remote-endpoint = <&ope2_cif_in_ep>;
+					};
+				};
+
+				port@44 {
+					reg = <0x44>;
+
+					xbar_ope2_out_ep: endpoint {
+						remote-endpoint = <&ope2_cif_out_ep>;
+					};
+				};
 			};
 		};
 	};
@@ -1637,7 +1701,7 @@
 		status = "okay";
 
 		flash@0 {
-			compatible = "spi-nor";
+			compatible = "jedec,spi-nor";
 			reg = <0>;
 			spi-max-frequency = <104000000>;
 			spi-tx-bus-width = <2>;
@@ -1645,7 +1709,7 @@
 		};
 	};
 
-	clk32k_in: clock@0 {
+	clk32k_in: clock-32k {
 		compatible = "fixed-clock";
 		clock-frequency = <32768>;
 		#clock-cells = <0>;
@@ -1675,7 +1739,7 @@
 		};
 	};
 
-	fan: fan {
+	fan: pwm-fan {
 		compatible = "pwm-fan";
 		pwms = <&pwm 3 45334>;
 
@@ -1684,7 +1748,7 @@
 	};
 
 	thermal-zones {
-		cpu {
+		cpu-thermal {
 			trips {
 				cpu_trip_critical: critical {
 					temperature = <96500>;
@@ -1738,7 +1802,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		power {
+		key-power {
 			label = "Power";
 			gpios = <&gpio TEGRA_GPIO(X, 5) GPIO_ACTIVE_LOW>;
 			linux,input-type = <EV_KEY>;
@@ -1748,7 +1812,7 @@
 			wakeup-source;
 		};
 
-		force-recovery {
+		key-force-recovery {
 			label = "Force Recovery";
 			gpios = <&gpio TEGRA_GPIO(X, 6) GPIO_ACTIVE_LOW>;
 			linux,input-type = <EV_KEY>;
@@ -1762,7 +1826,7 @@
 		method = "smc";
 	};
 
-	vdd_5v0_sys: regulator@0 {
+	vdd_5v0_sys: regulator-vdd-5v0-sys {
 		compatible = "regulator-fixed";
 
 		regulator-name = "VDD_5V0_SYS";
@@ -1772,14 +1836,13 @@
 		regulator-boot-on;
 	};
 
-	vdd_3v3_sys: regulator@1 {
+	vdd_3v3_sys: regulator-vdd-3v3-sys {
 		compatible = "regulator-fixed";
 
 		regulator-name = "VDD_3V3_SYS";
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
 		regulator-enable-ramp-delay = <240>;
-		regulator-disable-ramp-delay = <11340>;
 		regulator-always-on;
 		regulator-boot-on;
 
@@ -1789,7 +1852,7 @@
 		vin-supply = <&vdd_5v0_sys>;
 	};
 
-	vdd_3v3_sd: regulator@2 {
+	vdd_3v3_sd: regulator-vdd-3v3-sd {
 		compatible = "regulator-fixed";
 
 		regulator-name = "VDD_3V3_SD";
@@ -1802,7 +1865,7 @@
 		vin-supply = <&vdd_3v3_sys>;
 	};
 
-	vdd_hdmi: regulator@3 {
+	vdd_hdmi: regulator-vdd-hdmi-5v0 {
 		compatible = "regulator-fixed";
 
 		regulator-name = "VDD_HDMI_5V0";
@@ -1812,7 +1875,7 @@
 		vin-supply = <&vdd_5v0_sys>;
 	};
 
-	vdd_hub_3v3: regulator@4 {
+	vdd_hub_3v3: regulator-vdd-hub-3v3 {
 		compatible = "regulator-fixed";
 
 		regulator-name = "VDD_HUB_3V3";
@@ -1825,7 +1888,7 @@
 		vin-supply = <&vdd_5v0_sys>;
 	};
 
-	vdd_cpu: regulator@5 {
+	vdd_cpu: regulator-vdd-cpu {
 		compatible = "regulator-fixed";
 
 		regulator-name = "VDD_CPU";
@@ -1840,7 +1903,7 @@
 		vin-supply = <&vdd_5v0_sys>;
 	};
 
-	vdd_gpu: regulator@6 {
+	vdd_gpu: regulator-vdd-gpu {
 		compatible = "pwm-regulator";
 		pwms = <&pwm 1 8000>;
 
@@ -1855,7 +1918,7 @@
 		vin-supply = <&vdd_5v0_sys>;
 	};
 
-	avdd_io_edp_1v05: regulator@7 {
+	avdd_io_edp_1v05: regulator-avdd-io-epd-1v05 {
 		compatible = "regulator-fixed";
 
 		regulator-name = "AVDD_IO_EDP_1V05";
@@ -1868,7 +1931,7 @@
 		vin-supply = <&avdd_1v05_pll>;
 	};
 
-	vdd_5v0_usb: regulator@8 {
+	vdd_5v0_usb: regulator-vdd-5v-usb {
 		compatible = "regulator-fixed";
 
 		regulator-name = "VDD_5V_USB";
@@ -1903,6 +1966,7 @@
 		       <&xbar_mixer_in5_port>, <&xbar_mixer_in6_port>,
 		       <&xbar_mixer_in7_port>, <&xbar_mixer_in8_port>,
 		       <&xbar_mixer_in9_port>, <&xbar_mixer_in10_port>,
+		       <&xbar_ope1_in_port>, <&xbar_ope2_in_port>,
 		       /* HW accelerators */
 		       <&sfc1_out_port>, <&sfc2_out_port>,
 		       <&sfc3_out_port>, <&sfc4_out_port>,
@@ -1915,6 +1979,7 @@
 		       <&mixer_out1_port>, <&mixer_out2_port>,
 		       <&mixer_out3_port>, <&mixer_out4_port>,
 		       <&mixer_out5_port>,
+		       <&ope1_out_port>, <&ope2_out_port>,
 		       /* I/O DAP Ports */
 		       <&i2s3_port>, <&i2s4_port>,
 		       <&dmic1_port>, <&dmic2_port>;
diff --git a/arch/arm64/boot/dts/nvidia/tegra210-smaug.dts b/arch/arm64/boot/dts/nvidia/tegra210-smaug.dts
index 131c064d6991..7c569695b705 100644
--- a/arch/arm64/boot/dts/nvidia/tegra210-smaug.dts
+++ b/arch/arm64/boot/dts/nvidia/tegra210-smaug.dts
@@ -17,6 +17,7 @@
 
 	aliases {
 		serial0 = &uarta;
+		serial3 = &uartd;
 	};
 
 	chosen {
@@ -1309,6 +1310,22 @@
 		status = "okay";
 	};
 
+	uartd: serial@70006300 {
+		compatible = "nvidia,tegra30-hsuart";
+		status = "okay";
+
+		bluetooth {
+			compatible = "brcm,bcm43540-bt";
+			max-speed = <4000000>;
+			brcm,bt-pcm-int-params = [01 02 00 01 01];
+			device-wakeup-gpios = <&gpio TEGRA_GPIO(H, 3) GPIO_ACTIVE_HIGH>;
+			shutdown-gpios = <&gpio TEGRA_GPIO(H, 4) GPIO_ACTIVE_HIGH>;
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(H, 5) IRQ_TYPE_LEVEL_LOW>;
+			interrupt-names = "host-wakeup";
+		};
+	};
+
 	i2c@7000c400 {
 		status = "okay";
 		clock-frequency = <1000000>;
@@ -1642,10 +1659,6 @@
 		dvddio-pex-supply = <&avddio_1v05>;
 		hvddio-pex-supply = <&pp1800>;
 		avdd-usb-supply = <&pp3300>;
-		avdd-pll-utmip-supply = <&pp1800>;
-		avdd-pll-uerefe-supply = <&pp1050_avdd>;
-		dvdd-pex-pll-supply = <&avddio_1v05>;
-		hvdd-pex-pll-e-supply = <&pp1800>;
 
 		status = "okay";
 	};
@@ -1696,6 +1709,25 @@
 		};
 	};
 
+	mmc@700b0200 {
+		power-gpios = <&gpio TEGRA_GPIO(H, 1) GPIO_ACTIVE_HIGH>;
+		bus-width = <4>;
+		non-removable;
+		vqmmc-supply = <&pp1800>;
+		vmmc-supply = <&pp3300>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "okay";
+
+		wifi@1 {
+			compatible = "brcm,bcm4354-fmac", "brcm,bcm4329-fmac";
+			reg = <1>;
+			interrupt-parent = <&gpio>;
+			interrupts = <TEGRA_GPIO(H, 2) IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "host-wake";
+		};
+	};
+
 	mmc@700b0600 {
 		bus-width = <8>;
 		non-removable;
@@ -1726,7 +1758,7 @@
 		};
 	};
 
-	clk32k_in: clock@0 {
+	clk32k_in: clock-32k {
 		compatible = "fixed-clock";
 		clock-frequency = <32768>;
 		#clock-cells = <0>;
@@ -1760,7 +1792,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		power {
+		key-power {
 			label = "Power";
 			gpios = <&gpio TEGRA_GPIO(X, 5) GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
@@ -1768,7 +1800,7 @@
 			wakeup-source;
 		};
 
-		lid {
+		switch-lid {
 			label = "Lid";
 			gpios = <&gpio TEGRA_GPIO(B, 4) GPIO_ACTIVE_LOW>;
 			linux,input-type = <EV_SW>;
@@ -1776,7 +1808,7 @@
 			wakeup-source;
 		};
 
-		tablet_mode {
+		switch-tablet-mode {
 			label = "Tablet Mode";
 			gpios = <&gpio TEGRA_GPIO(Z, 2) GPIO_ACTIVE_HIGH>;
 			linux,input-type = <EV_SW>;
@@ -1784,13 +1816,13 @@
 			wakeup-source;
 		};
 
-		volume_down {
+		key-volume-down {
 			label = "Volume Down";
 			gpios = <&gpio TEGRA_GPIO(X, 7) GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_VOLUMEDOWN>;
 		};
 
-		volume_up {
+		key-volume-up {
 			label = "Volume Up";
 			gpios = <&gpio TEGRA_GPIO(M, 4) GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_VOLUMEUP>;
@@ -1807,7 +1839,7 @@
 		method = "smc";
 	};
 
-	ppvar_sys: regulator@0 {
+	ppvar_sys: regulator-ppvar-sys {
 		compatible = "regulator-fixed";
 		regulator-name = "PPVAR_SYS";
 		regulator-min-microvolt = <4400000>;
@@ -1815,7 +1847,7 @@
 		regulator-always-on;
 	};
 
-	pplcd_vdd: regulator@1 {
+	pplcd_vdd: regulator-pplcd-vdd {
 		compatible = "regulator-fixed";
 		regulator-name = "PPLCD_VDD";
 		regulator-min-microvolt = <4400000>;
@@ -1825,7 +1857,7 @@
 		regulator-boot-on;
 	};
 
-	pp3000_always: regulator@2 {
+	pp3000_always: regulator-pp3000-always {
 		compatible = "regulator-fixed";
 		regulator-name = "PP3000_ALWAYS";
 		regulator-min-microvolt = <3000000>;
@@ -1833,7 +1865,7 @@
 		regulator-always-on;
 	};
 
-	pp3300: regulator@3 {
+	pp3300: regulator-pp3000 {
 		compatible = "regulator-fixed";
 		regulator-name = "PP3300";
 		regulator-min-microvolt = <3300000>;
@@ -1843,7 +1875,7 @@
 		enable-active-high;
 	};
 
-	pp5000: regulator@4 {
+	pp5000: regulator-pp5000 {
 		compatible = "regulator-fixed";
 		regulator-name = "PP5000";
 		regulator-min-microvolt = <5000000>;
@@ -1851,7 +1883,7 @@
 		regulator-always-on;
 	};
 
-	pp1800_lcdio: regulator@5 {
+	pp1800_lcdio: regulator-pp1800-lcdio {
 		compatible = "regulator-fixed";
 		regulator-name = "PP1800_LCDIO";
 		regulator-min-microvolt = <1800000>;
@@ -1861,7 +1893,7 @@
 		regulator-boot-on;
 	};
 
-	pp1800_cam: regulator@6 {
+	pp1800_cam: regulator-pp1800-cam {
 		compatible = "regulator-fixed";
 		regulator-name = "PP1800_CAM";
 		regulator-min-microvolt = <1800000>;
@@ -1870,7 +1902,7 @@
 		enable-active-high;
 	};
 
-	usbc_vbus: regulator@7 {
+	usbc_vbus: regulator-usbc-vbus {
 		compatible = "regulator-fixed";
 		regulator-name = "USBC_VBUS";
 		regulator-min-microvolt = <5000000>;
diff --git a/arch/arm64/boot/dts/nvidia/tegra210.dtsi b/arch/arm64/boot/dts/nvidia/tegra210.dtsi
index ccdc0dec4e59..724e87450605 100644
--- a/arch/arm64/boot/dts/nvidia/tegra210.dtsi
+++ b/arch/arm64/boot/dts/nvidia/tegra210.dtsi
@@ -93,8 +93,8 @@
 		interrupt-names = "syncpt", "host1x";
 		clocks = <&tegra_car TEGRA210_CLK_HOST1X>;
 		clock-names = "host1x";
-		resets = <&tegra_car 28>;
-		reset-names = "host1x";
+		resets = <&tegra_car 28>, <&mc TEGRA210_MC_RESET_HC>;
+		reset-names = "host1x", "mc";
 
 		#address-cells = <2>;
 		#size-cells = <2>;
@@ -181,6 +181,12 @@
 		tsec@54100000 {
 			compatible = "nvidia,tegra210-tsec";
 			reg = <0x0 0x54100000 0x0 0x00040000>;
+			interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&tegra_car TEGRA210_CLK_TSEC>;
+			clock-names = "tsec";
+			resets = <&tegra_car 83>;
+			reset-names = "tsec";
+			status = "disabled";
 		};
 
 		dc@54200000 {
@@ -283,6 +289,11 @@
 		tsec@54500000 {
 			compatible = "nvidia,tegra210-tsec";
 			reg = <0x0 0x54500000 0x0 0x00040000>;
+			interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&tegra_car TEGRA210_CLK_TSECB>;
+			clock-names = "tsec";
+			resets = <&tegra_car 206>;
+			reset-names = "tsec";
 			status = "disabled";
 		};
 
@@ -1015,8 +1026,8 @@
 			 <&tegra_car TEGRA210_CLK_XUSB_HOST_SRC>,
 			 <&tegra_car TEGRA210_CLK_XUSB_FALCON_SRC>,
 			 <&tegra_car TEGRA210_CLK_XUSB_SS>,
-			 <&tegra_car TEGRA210_CLK_XUSB_SS_SRC>,
 			 <&tegra_car TEGRA210_CLK_XUSB_SS_DIV2>,
+			 <&tegra_car TEGRA210_CLK_XUSB_SS_SRC>,
 			 <&tegra_car TEGRA210_CLK_XUSB_HS_SRC>,
 			 <&tegra_car TEGRA210_CLK_XUSB_FS_SRC>,
 			 <&tegra_car TEGRA210_CLK_PLL_U_480M>,
@@ -1024,7 +1035,7 @@
 			 <&tegra_car TEGRA210_CLK_PLL_E>;
 		clock-names = "xusb_host", "xusb_host_src",
 			      "xusb_falcon_src", "xusb_ss",
-			      "xusb_ss_src", "xusb_ss_div2",
+			      "xusb_ss_div2", "xusb_ss_src",
 			      "xusb_hs_src", "xusb_fs_src",
 			      "pll_u_480m", "clk_m", "pll_e";
 		resets = <&tegra_car 89>, <&tegra_car 156>,
@@ -1044,7 +1055,7 @@
 		interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
 		resets = <&tegra_car 142>;
 		reset-names = "padctl";
-		nvidia,pmc =  <&tegra_pmc>;
+		nvidia,pmc = <&tegra_pmc>;
 
 		status = "disabled";
 
@@ -1355,8 +1366,9 @@
 			 <&tegra_car TEGRA210_CLK_DFLL_REF>,
 			 <&tegra_car TEGRA210_CLK_I2C5>;
 		clock-names = "soc", "ref", "i2c";
-		resets = <&tegra_car TEGRA210_RST_DFLL_DVCO>;
-		reset-names = "dvco";
+		resets = <&tegra_car TEGRA210_RST_DFLL_DVCO>,
+			 <&tegra_car 155>;
+		reset-names = "dvco", "dfll";
 		#clock-cells = <0>;
 		clock-output-names = "dfllCPU_out";
 		status = "disabled";
@@ -1711,6 +1723,46 @@
 				status = "disabled";
 			};
 
+			tegra_ope1: processing-engine@702d8000 {
+				compatible = "nvidia,tegra210-ope";
+				reg = <0x702d8000 0x100>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges;
+				sound-name-prefix = "OPE1";
+				status = "disabled";
+
+				equalizer@702d8100 {
+					compatible = "nvidia,tegra210-peq";
+					reg = <0x702d8100 0x100>;
+				};
+
+				dynamic-range-compressor@702d8200 {
+					compatible = "nvidia,tegra210-mbdrc";
+					reg = <0x702d8200 0x200>;
+				};
+			};
+
+			tegra_ope2: processing-engine@702d8400 {
+				compatible = "nvidia,tegra210-ope";
+				reg = <0x702d8400 0x100>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges;
+				sound-name-prefix = "OPE2";
+				status = "disabled";
+
+				equalizer@702d8500 {
+					compatible = "nvidia,tegra210-peq";
+					reg = <0x702d8500 0x100>;
+				};
+
+				dynamic-range-compressor@702d8600 {
+					compatible = "nvidia,tegra210-mbdrc";
+					reg = <0x702d8600 0x200>;
+				};
+			};
+
 			tegra_amixer: amixer@702dbb00 {
 				compatible = "nvidia,tegra210-amixer";
 				reg = <0x702dbb00 0x800>;
@@ -1981,7 +2033,7 @@
 	};
 
 	thermal-zones {
-		cpu {
+		cpu-thermal {
 			polling-delay-passive = <1000>;
 			polling-delay = <0>;
 
@@ -2010,7 +2062,7 @@
 			};
 		};
 
-		mem {
+		mem-thermal {
 			polling-delay-passive = <0>;
 			polling-delay = <0>;
 
@@ -2056,7 +2108,7 @@
 			};
 		};
 
-		gpu {
+		gpu-thermal {
 			polling-delay-passive = <1000>;
 			polling-delay = <0>;
 
@@ -2085,7 +2137,7 @@
 			};
 		};
 
-		pllx {
+		pllx-thermal {
 			polling-delay-passive = <0>;
 			polling-delay = <0>;
 
diff --git a/arch/arm64/boot/dts/nvidia/tegra234-p3701-0000.dtsi b/arch/arm64/boot/dts/nvidia/tegra234-p3701-0000.dtsi
new file mode 100644
index 000000000000..9e4d72cfa69f
--- /dev/null
+++ b/arch/arm64/boot/dts/nvidia/tegra234-p3701-0000.dtsi
@@ -0,0 +1,72 @@
+// SPDX-License-Identifier: GPL-2.0
+
+#include "tegra234.dtsi"
+
+/ {
+	model = "NVIDIA Jetson AGX Orin";
+	compatible = "nvidia,p3701-0000", "nvidia,tegra234";
+
+	vdd_1v8_ls: regulator-vdd-1v8-ls {
+		compatible = "regulator-fixed";
+		regulator-name = "VDD_1V8_LS";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
+	};
+
+	vdd_1v8_ao: regulator-vdd-1v8-ao {
+		compatible = "regulator-fixed";
+		regulator-name = "VDD_1V8_AO";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
+	};
+
+	vdd_3v3_pcie: regulator-vdd-3v3-pcie {
+		compatible = "regulator-fixed";
+		regulator-name = "VDD_3V3_PCIE";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio TEGRA234_MAIN_GPIO(Z, 2) GPIO_ACTIVE_HIGH>;
+		regulator-boot-on;
+		enable-active-high;
+	};
+
+	vdd_12v_pcie: regulator-vdd-12v-pcie {
+		compatible = "regulator-fixed";
+		regulator-name = "VDD_12V_PCIE";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		gpio = <&gpio TEGRA234_MAIN_GPIO(A, 1) GPIO_ACTIVE_LOW>;
+		regulator-boot-on;
+		enable-active-low;
+	};
+
+	bus@0 {
+		spi@3270000 {
+			status = "okay";
+
+			flash@0 {
+				compatible = "jedec,spi-nor";
+				reg = <0>;
+				spi-max-frequency = <102000000>;
+				spi-tx-bus-width = <4>;
+				spi-rx-bus-width = <4>;
+			};
+		};
+
+		mmc@3460000 {
+			status = "okay";
+			bus-width = <8>;
+			non-removable;
+		};
+
+		rtc@c2a0000 {
+			status = "okay";
+		};
+
+		pmc@c360000 {
+			nvidia,invert-interrupt;
+		};
+	};
+};
diff --git a/arch/arm64/boot/dts/nvidia/tegra234-p3737-0000+p3701-0000.dts b/arch/arm64/boot/dts/nvidia/tegra234-p3737-0000+p3701-0000.dts
new file mode 100644
index 000000000000..57ab75328814
--- /dev/null
+++ b/arch/arm64/boot/dts/nvidia/tegra234-p3737-0000+p3701-0000.dts
@@ -0,0 +1,2187 @@
+// SPDX-License-Identifier: GPL-2.0
+/dts-v1/;
+
+#include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/input/gpio-keys.h>
+
+#include "tegra234-p3701-0000.dtsi"
+#include "tegra234-p3737-0000.dtsi"
+
+/ {
+	model = "NVIDIA Jetson AGX Orin Developer Kit";
+	compatible = "nvidia,p3737-0000+p3701-0000", "nvidia,p3701-0000", "nvidia,tegra234";
+
+	aliases {
+		mmc3 = "/bus@0/mmc@3460000";
+		serial0 = &tcu;
+		serial1 = &uarta;
+	};
+
+	bus@0 {
+		aconnect@2900000 {
+			status = "okay";
+
+			ahub@2900800 {
+				status = "okay";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0x0>;
+
+						xbar_admaif0: endpoint {
+							remote-endpoint = <&admaif0>;
+						};
+					};
+
+					port@1 {
+						reg = <0x1>;
+
+						xbar_admaif1: endpoint {
+							remote-endpoint = <&admaif1>;
+						};
+					};
+
+					port@2 {
+						reg = <0x2>;
+
+						xbar_admaif2: endpoint {
+							remote-endpoint = <&admaif2>;
+						};
+					};
+
+					port@3 {
+						reg = <0x3>;
+
+						xbar_admaif3: endpoint {
+							remote-endpoint = <&admaif3>;
+						};
+					};
+
+					port@4 {
+						reg = <0x4>;
+
+						xbar_admaif4: endpoint {
+							remote-endpoint = <&admaif4>;
+						};
+					};
+
+					port@5 {
+						reg = <0x5>;
+
+						xbar_admaif5: endpoint {
+							remote-endpoint = <&admaif5>;
+						};
+					};
+
+					port@6 {
+						reg = <0x6>;
+
+						xbar_admaif6: endpoint {
+							remote-endpoint = <&admaif6>;
+						};
+					};
+
+					port@7 {
+						reg = <0x7>;
+
+						xbar_admaif7: endpoint {
+							remote-endpoint = <&admaif7>;
+						};
+					};
+
+					port@8 {
+						reg = <0x8>;
+
+						xbar_admaif8: endpoint {
+							remote-endpoint = <&admaif8>;
+						};
+					};
+
+					port@9 {
+						reg = <0x9>;
+
+						xbar_admaif9: endpoint {
+							remote-endpoint = <&admaif9>;
+						};
+					};
+
+					port@a {
+						reg = <0xa>;
+
+						xbar_admaif10: endpoint {
+							remote-endpoint = <&admaif10>;
+						};
+					};
+
+					port@b {
+						reg = <0xb>;
+
+						xbar_admaif11: endpoint {
+							remote-endpoint = <&admaif11>;
+						};
+					};
+
+					port@c {
+						reg = <0xc>;
+
+						xbar_admaif12: endpoint {
+							remote-endpoint = <&admaif12>;
+						};
+					};
+
+					port@d {
+						reg = <0xd>;
+
+						xbar_admaif13: endpoint {
+							remote-endpoint = <&admaif13>;
+						};
+					};
+
+					port@e {
+						reg = <0xe>;
+
+						xbar_admaif14: endpoint {
+							remote-endpoint = <&admaif14>;
+						};
+					};
+
+					port@f {
+						reg = <0xf>;
+
+						xbar_admaif15: endpoint {
+							remote-endpoint = <&admaif15>;
+						};
+					};
+
+					port@10 {
+						reg = <0x10>;
+
+						xbar_admaif16: endpoint {
+							remote-endpoint = <&admaif16>;
+						};
+					};
+
+					port@11 {
+						reg = <0x11>;
+
+						xbar_admaif17: endpoint {
+							remote-endpoint = <&admaif17>;
+						};
+					};
+
+					port@12 {
+						reg = <0x12>;
+
+						xbar_admaif18: endpoint {
+							remote-endpoint = <&admaif18>;
+						};
+					};
+
+					port@13 {
+						reg = <0x13>;
+
+						xbar_admaif19: endpoint {
+							remote-endpoint = <&admaif19>;
+						};
+					};
+
+					xbar_i2s1_port: port@14 {
+						reg = <0x14>;
+
+						xbar_i2s1: endpoint {
+							remote-endpoint = <&i2s1_cif>;
+						};
+					};
+
+					xbar_i2s2_port: port@15 {
+						reg = <0x15>;
+
+						xbar_i2s2: endpoint {
+							remote-endpoint = <&i2s2_cif>;
+						};
+					};
+
+					xbar_i2s4_port: port@17 {
+						reg = <0x17>;
+
+						xbar_i2s4: endpoint {
+							remote-endpoint = <&i2s4_cif>;
+						};
+					};
+
+					xbar_i2s6_port: port@19 {
+						reg = <0x19>;
+
+						xbar_i2s6: endpoint {
+							remote-endpoint = <&i2s6_cif>;
+						};
+					};
+
+					xbar_dmic3_port: port@1c {
+						reg = <0x1c>;
+
+						xbar_dmic3: endpoint {
+							remote-endpoint = <&dmic3_cif>;
+						};
+					};
+
+					xbar_sfc1_in_port: port@20 {
+						reg = <0x20>;
+
+						xbar_sfc1_in: endpoint {
+							remote-endpoint = <&sfc1_cif_in>;
+						};
+					};
+
+					port@21 {
+						reg = <0x21>;
+
+						xbar_sfc1_out: endpoint {
+							remote-endpoint = <&sfc1_cif_out>;
+						};
+					};
+
+					xbar_sfc2_in_port: port@22 {
+						reg = <0x22>;
+
+						xbar_sfc2_in: endpoint {
+							remote-endpoint = <&sfc2_cif_in>;
+						};
+					};
+
+					port@23 {
+						reg = <0x23>;
+
+						xbar_sfc2_out: endpoint {
+							remote-endpoint = <&sfc2_cif_out>;
+						};
+					};
+
+					xbar_sfc3_in_port: port@24 {
+						reg = <0x24>;
+
+						xbar_sfc3_in: endpoint {
+							remote-endpoint = <&sfc3_cif_in>;
+						};
+					};
+
+					port@25 {
+						reg = <0x25>;
+
+						xbar_sfc3_out: endpoint {
+							remote-endpoint = <&sfc3_cif_out>;
+						};
+					};
+
+					xbar_sfc4_in_port: port@26 {
+						reg = <0x26>;
+
+						xbar_sfc4_in: endpoint {
+							remote-endpoint = <&sfc4_cif_in>;
+						};
+					};
+
+					port@27 {
+						reg = <0x27>;
+
+						xbar_sfc4_out: endpoint {
+							remote-endpoint = <&sfc4_cif_out>;
+						};
+					};
+
+					xbar_mvc1_in_port: port@28 {
+						reg = <0x28>;
+
+						xbar_mvc1_in: endpoint {
+							remote-endpoint = <&mvc1_cif_in>;
+						};
+					};
+
+					port@29 {
+						reg = <0x29>;
+
+						xbar_mvc1_out: endpoint {
+							remote-endpoint = <&mvc1_cif_out>;
+						};
+					};
+
+					xbar_mvc2_in_port: port@2a {
+						reg = <0x2a>;
+
+						xbar_mvc2_in: endpoint {
+							remote-endpoint = <&mvc2_cif_in>;
+						};
+					};
+
+					port@2b {
+						reg = <0x2b>;
+
+						xbar_mvc2_out: endpoint {
+							remote-endpoint = <&mvc2_cif_out>;
+						};
+					};
+
+					xbar_amx1_in1_port: port@2c {
+						reg = <0x2c>;
+
+						xbar_amx1_in1: endpoint {
+							remote-endpoint = <&amx1_in1>;
+						};
+					};
+
+					xbar_amx1_in2_port: port@2d {
+						reg = <0x2d>;
+
+						xbar_amx1_in2: endpoint {
+							remote-endpoint = <&amx1_in2>;
+						};
+					};
+
+					xbar_amx1_in3_port: port@2e {
+						reg = <0x2e>;
+
+						xbar_amx1_in3: endpoint {
+							remote-endpoint = <&amx1_in3>;
+						};
+					};
+
+					xbar_amx1_in4_port: port@2f {
+						reg = <0x2f>;
+
+						xbar_amx1_in4: endpoint {
+							remote-endpoint = <&amx1_in4>;
+						};
+					};
+
+					port@30 {
+						reg = <0x30>;
+
+						xbar_amx1_out: endpoint {
+							remote-endpoint = <&amx1_out>;
+						};
+					};
+
+					xbar_amx2_in1_port: port@31 {
+						reg = <0x31>;
+
+						xbar_amx2_in1: endpoint {
+							remote-endpoint = <&amx2_in1>;
+						};
+					};
+
+					xbar_amx2_in2_port: port@32 {
+						reg = <0x32>;
+
+						xbar_amx2_in2: endpoint {
+							remote-endpoint = <&amx2_in2>;
+						};
+					};
+
+					xbar_amx2_in3_port: port@33 {
+						reg = <0x33>;
+
+						xbar_amx2_in3: endpoint {
+							remote-endpoint = <&amx2_in3>;
+						};
+					};
+
+					xbar_amx2_in4_port: port@34 {
+						reg = <0x34>;
+
+						xbar_amx2_in4: endpoint {
+							remote-endpoint = <&amx2_in4>;
+						};
+					};
+
+					port@35 {
+						reg = <0x35>;
+
+						xbar_amx2_out: endpoint {
+							remote-endpoint = <&amx2_out>;
+						};
+					};
+
+					xbar_amx3_in1_port: port@36 {
+						reg = <0x36>;
+
+						xbar_amx3_in1: endpoint {
+							remote-endpoint = <&amx3_in1>;
+						};
+					};
+
+					xbar_amx3_in2_port: port@37 {
+						reg = <0x37>;
+
+						xbar_amx3_in2: endpoint {
+							remote-endpoint = <&amx3_in2>;
+						};
+					};
+
+					xbar_amx3_in3_port: port@38 {
+						reg = <0x38>;
+
+						xbar_amx3_in3: endpoint {
+							remote-endpoint = <&amx3_in3>;
+						};
+					};
+
+					xbar_amx3_in4_port: port@39 {
+						reg = <0x39>;
+
+						xbar_amx3_in4: endpoint {
+							remote-endpoint = <&amx3_in4>;
+						};
+					};
+
+					port@3a {
+						reg = <0x3a>;
+
+						xbar_amx3_out: endpoint {
+							remote-endpoint = <&amx3_out>;
+						};
+					};
+
+					xbar_amx4_in1_port: port@3b {
+						reg = <0x3b>;
+
+						xbar_amx4_in1: endpoint {
+							remote-endpoint = <&amx4_in1>;
+						};
+					};
+
+					xbar_amx4_in2_port: port@3c {
+						reg = <0x3c>;
+
+						xbar_amx4_in2: endpoint {
+							remote-endpoint = <&amx4_in2>;
+						};
+					};
+
+					xbar_amx4_in3_port: port@3d {
+						reg = <0x3d>;
+
+						xbar_amx4_in3: endpoint {
+							remote-endpoint = <&amx4_in3>;
+						};
+					};
+
+					xbar_amx4_in4_port: port@3e {
+						reg = <0x3e>;
+
+						xbar_amx4_in4: endpoint {
+							remote-endpoint = <&amx4_in4>;
+						};
+					};
+
+					port@3f {
+						reg = <0x3f>;
+
+						xbar_amx4_out: endpoint {
+							remote-endpoint = <&amx4_out>;
+						};
+					};
+
+					xbar_adx1_in_port: port@40 {
+						reg = <0x40>;
+
+						xbar_adx1_in: endpoint {
+							remote-endpoint = <&adx1_in>;
+						};
+					};
+
+					port@41 {
+						reg = <0x41>;
+
+						xbar_adx1_out1: endpoint {
+							remote-endpoint = <&adx1_out1>;
+						};
+					};
+
+					port@42 {
+						reg = <0x42>;
+
+						xbar_adx1_out2: endpoint {
+							remote-endpoint = <&adx1_out2>;
+						};
+					};
+
+					port@43 {
+						reg = <0x43>;
+
+						xbar_adx1_out3: endpoint {
+							remote-endpoint = <&adx1_out3>;
+						};
+					};
+
+					port@44 {
+						reg = <0x44>;
+
+						xbar_adx1_out4: endpoint {
+							remote-endpoint = <&adx1_out4>;
+						};
+					};
+
+					xbar_adx2_in_port: port@45 {
+						reg = <0x45>;
+
+						xbar_adx2_in: endpoint {
+							remote-endpoint = <&adx2_in>;
+						};
+					};
+
+					port@46 {
+						reg = <0x46>;
+
+						xbar_adx2_out1: endpoint {
+							remote-endpoint = <&adx2_out1>;
+						};
+					};
+
+					port@47 {
+						reg = <0x47>;
+
+						xbar_adx2_out2: endpoint {
+							remote-endpoint = <&adx2_out2>;
+						};
+					};
+
+					port@48 {
+						reg = <0x48>;
+
+						xbar_adx2_out3: endpoint {
+							remote-endpoint = <&adx2_out3>;
+						};
+					};
+
+					port@49 {
+						reg = <0x49>;
+
+						xbar_adx2_out4: endpoint {
+							remote-endpoint = <&adx2_out4>;
+						};
+					};
+
+					xbar_adx3_in_port: port@4a {
+						reg = <0x4a>;
+
+						xbar_adx3_in: endpoint {
+							remote-endpoint = <&adx3_in>;
+						};
+					};
+
+					port@4b {
+						reg = <0x4b>;
+
+						xbar_adx3_out1: endpoint {
+							remote-endpoint = <&adx3_out1>;
+						};
+					};
+
+					port@4c {
+						reg = <0x4c>;
+
+						xbar_adx3_out2: endpoint {
+							remote-endpoint = <&adx3_out2>;
+						};
+					};
+
+					port@4d {
+						reg = <0x4d>;
+
+						xbar_adx3_out3: endpoint {
+							remote-endpoint = <&adx3_out3>;
+						};
+					};
+
+					port@4e {
+						reg = <0x4e>;
+
+						xbar_adx3_out4: endpoint {
+							remote-endpoint = <&adx3_out4>;
+						};
+					};
+
+					xbar_adx4_in_port: port@4f {
+						reg = <0x4f>;
+
+						xbar_adx4_in: endpoint {
+							remote-endpoint = <&adx4_in>;
+						};
+					};
+
+					port@50 {
+						reg = <0x50>;
+
+						xbar_adx4_out1: endpoint {
+							remote-endpoint = <&adx4_out1>;
+						};
+					};
+
+					port@51 {
+						reg = <0x51>;
+
+						xbar_adx4_out2: endpoint {
+							remote-endpoint = <&adx4_out2>;
+						};
+					};
+
+					port@52 {
+						reg = <0x52>;
+
+						xbar_adx4_out3: endpoint {
+							remote-endpoint = <&adx4_out3>;
+						};
+					};
+
+					port@53 {
+						reg = <0x53>;
+
+						xbar_adx4_out4: endpoint {
+							remote-endpoint = <&adx4_out4>;
+						};
+					};
+
+					xbar_mix_in1_port: port@54 {
+						reg = <0x54>;
+
+						xbar_mix_in1: endpoint {
+							remote-endpoint = <&mix_in1>;
+						};
+					};
+
+					xbar_mix_in2_port: port@55 {
+						reg = <0x55>;
+
+						xbar_mix_in2: endpoint {
+							remote-endpoint = <&mix_in2>;
+						};
+					};
+
+					xbar_mix_in3_port: port@56 {
+						reg = <0x56>;
+
+						xbar_mix_in3: endpoint {
+							remote-endpoint = <&mix_in3>;
+						};
+					};
+
+					xbar_mix_in4_port: port@57 {
+						reg = <0x57>;
+
+						xbar_mix_in4: endpoint {
+							remote-endpoint = <&mix_in4>;
+						};
+					};
+
+					xbar_mix_in5_port: port@58 {
+						reg = <0x58>;
+
+						xbar_mix_in5: endpoint {
+							remote-endpoint = <&mix_in5>;
+						};
+					};
+
+					xbar_mix_in6_port: port@59 {
+						reg = <0x59>;
+
+						xbar_mix_in6: endpoint {
+							remote-endpoint = <&mix_in6>;
+						};
+					};
+
+					xbar_mix_in7_port: port@5a {
+						reg = <0x5a>;
+
+						xbar_mix_in7: endpoint {
+							remote-endpoint = <&mix_in7>;
+						};
+					};
+
+					xbar_mix_in8_port: port@5b {
+						reg = <0x5b>;
+
+						xbar_mix_in8: endpoint {
+							remote-endpoint = <&mix_in8>;
+						};
+					};
+
+					xbar_mix_in9_port: port@5c {
+						reg = <0x5c>;
+
+						xbar_mix_in9: endpoint {
+							remote-endpoint = <&mix_in9>;
+						};
+					};
+
+					xbar_mix_in10_port: port@5d {
+						reg = <0x5d>;
+
+						xbar_mix_in10: endpoint {
+							remote-endpoint = <&mix_in10>;
+						};
+					};
+
+					port@5e {
+						reg = <0x5e>;
+
+						xbar_mix_out1: endpoint {
+							remote-endpoint = <&mix_out1>;
+						};
+					};
+
+					port@5f {
+						reg = <0x5f>;
+
+						xbar_mix_out2: endpoint {
+							remote-endpoint = <&mix_out2>;
+						};
+					};
+
+					port@60 {
+						reg = <0x60>;
+
+						xbar_mix_out3: endpoint {
+							remote-endpoint = <&mix_out3>;
+						};
+					};
+
+					port@61 {
+						reg = <0x61>;
+
+						xbar_mix_out4: endpoint {
+							remote-endpoint = <&mix_out4>;
+						};
+					};
+
+					port@62 {
+						reg = <0x62>;
+
+						xbar_mix_out5: endpoint {
+							remote-endpoint = <&mix_out5>;
+						};
+					};
+
+					xbar_asrc_in1_port: port@63 {
+						reg = <0x63>;
+
+						xbar_asrc_in1_ep: endpoint {
+							remote-endpoint = <&asrc_in1_ep>;
+						};
+					};
+
+					port@64 {
+						reg = <0x64>;
+
+						xbar_asrc_out1_ep: endpoint {
+							remote-endpoint = <&asrc_out1_ep>;
+						};
+					};
+
+					xbar_asrc_in2_port: port@65 {
+						reg = <0x65>;
+
+						xbar_asrc_in2_ep: endpoint {
+							remote-endpoint = <&asrc_in2_ep>;
+						};
+					};
+
+					port@66 {
+						reg = <0x66>;
+
+						xbar_asrc_out2_ep: endpoint {
+							remote-endpoint = <&asrc_out2_ep>;
+						};
+					};
+
+					xbar_asrc_in3_port: port@67 {
+						reg = <0x67>;
+
+						xbar_asrc_in3_ep: endpoint {
+							remote-endpoint = <&asrc_in3_ep>;
+						};
+					};
+
+					port@68 {
+						reg = <0x68>;
+
+						xbar_asrc_out3_ep: endpoint {
+							remote-endpoint = <&asrc_out3_ep>;
+						};
+					};
+
+					xbar_asrc_in4_port: port@69 {
+						reg = <0x69>;
+
+						xbar_asrc_in4_ep: endpoint {
+							remote-endpoint = <&asrc_in4_ep>;
+						};
+					};
+
+					port@6a {
+						reg = <0x6a>;
+
+						xbar_asrc_out4_ep: endpoint {
+							remote-endpoint = <&asrc_out4_ep>;
+						};
+					};
+
+					xbar_asrc_in5_port: port@6b {
+						reg = <0x6b>;
+
+						xbar_asrc_in5_ep: endpoint {
+							remote-endpoint = <&asrc_in5_ep>;
+						};
+					};
+
+					port@6c {
+						reg = <0x6c>;
+
+						xbar_asrc_out5_ep: endpoint {
+							remote-endpoint = <&asrc_out5_ep>;
+						};
+					};
+
+					xbar_asrc_in6_port: port@6d {
+						reg = <0x6d>;
+
+						xbar_asrc_in6_ep: endpoint {
+							remote-endpoint = <&asrc_in6_ep>;
+						};
+					};
+
+					port@6e {
+						reg = <0x6e>;
+
+						xbar_asrc_out6_ep: endpoint {
+							remote-endpoint = <&asrc_out6_ep>;
+						};
+					};
+
+					xbar_asrc_in7_port: port@6f {
+						reg = <0x6f>;
+
+						xbar_asrc_in7_ep: endpoint {
+							remote-endpoint = <&asrc_in7_ep>;
+						};
+					};
+
+					xbar_ope1_in_port: port@70 {
+						reg = <0x70>;
+
+						xbar_ope1_in_ep: endpoint {
+							remote-endpoint = <&ope1_cif_in_ep>;
+						};
+					};
+
+					port@71 {
+						reg = <0x71>;
+
+						xbar_ope1_out_ep: endpoint {
+							remote-endpoint = <&ope1_cif_out_ep>;
+						};
+					};
+				};
+
+				i2s@2901000 {
+					status = "okay";
+
+					ports {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						port@0 {
+							reg = <0>;
+
+							i2s1_cif: endpoint {
+								remote-endpoint = <&xbar_i2s1>;
+							};
+						};
+
+						i2s1_port: port@1 {
+							reg = <1>;
+
+							i2s1_dap: endpoint {
+								dai-format = "i2s";
+								/* placeholder for external codec */
+							};
+						};
+					};
+				};
+
+				i2s@2901100 {
+					status = "okay";
+
+					ports {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						port@0 {
+							reg = <0>;
+
+							i2s2_cif: endpoint {
+								remote-endpoint = <&xbar_i2s2>;
+							};
+						};
+
+						i2s2_port: port@1 {
+							reg = <1>;
+
+							i2s2_dap: endpoint {
+								dai-format = "i2s";
+								/* placeholder for external codec */
+							};
+						};
+					};
+				};
+
+				i2s@2901300 {
+					status = "okay";
+
+					ports {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						port@0 {
+							reg = <0>;
+
+							i2s4_cif: endpoint {
+								remote-endpoint = <&xbar_i2s4>;
+							};
+						};
+
+						i2s4_port: port@1 {
+							reg = <1>;
+
+							i2s4_dap: endpoint {
+								dai-format = "i2s";
+								/* placeholder for external codec */
+							};
+						};
+					};
+				};
+
+				i2s@2901500 {
+					status = "okay";
+
+					ports {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						port@0 {
+							reg = <0>;
+
+							i2s6_cif: endpoint {
+								remote-endpoint = <&xbar_i2s6>;
+							};
+						};
+
+						i2s6_port: port@1 {
+							reg = <1>;
+
+							i2s6_dap: endpoint {
+								dai-format = "i2s";
+								/* placeholder for external codec */
+							};
+						};
+					};
+				};
+
+				sfc@2902000 {
+					status = "okay";
+
+					ports {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						port@0 {
+							reg = <0>;
+
+							sfc1_cif_in: endpoint {
+								remote-endpoint = <&xbar_sfc1_in>;
+							};
+						};
+
+						sfc1_out_port: port@1 {
+							reg = <1>;
+
+							sfc1_cif_out: endpoint {
+								remote-endpoint = <&xbar_sfc1_out>;
+							};
+						};
+					};
+				};
+
+				sfc@2902200 {
+					status = "okay";
+
+					ports {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						port@0 {
+							reg = <0>;
+
+							sfc2_cif_in: endpoint {
+								remote-endpoint = <&xbar_sfc2_in>;
+							};
+						};
+
+						sfc2_out_port: port@1 {
+							reg = <1>;
+
+							sfc2_cif_out: endpoint {
+								remote-endpoint = <&xbar_sfc2_out>;
+							};
+						};
+					};
+				};
+
+				sfc@2902400 {
+					status = "okay";
+
+					ports {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						port@0 {
+							reg = <0>;
+
+							sfc3_cif_in: endpoint {
+								remote-endpoint = <&xbar_sfc3_in>;
+							};
+						};
+
+						sfc3_out_port: port@1 {
+							reg = <1>;
+
+							sfc3_cif_out: endpoint {
+								remote-endpoint = <&xbar_sfc3_out>;
+							};
+						};
+					};
+				};
+
+				sfc@2902600 {
+					status = "okay";
+
+					ports {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						port@0 {
+							reg = <0>;
+
+							sfc4_cif_in: endpoint {
+								remote-endpoint = <&xbar_sfc4_in>;
+							};
+						};
+
+						sfc4_out_port: port@1 {
+							reg = <1>;
+
+							sfc4_cif_out: endpoint {
+								remote-endpoint = <&xbar_sfc4_out>;
+							};
+						};
+					};
+				};
+
+				amx@2903000 {
+					status = "okay";
+
+					ports {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						port@0 {
+							reg = <0>;
+
+							amx1_in1: endpoint {
+								remote-endpoint = <&xbar_amx1_in1>;
+							};
+						};
+
+						port@1 {
+							reg = <1>;
+
+							amx1_in2: endpoint {
+								remote-endpoint = <&xbar_amx1_in2>;
+							};
+						};
+
+						port@2 {
+							reg = <2>;
+
+							amx1_in3: endpoint {
+								remote-endpoint = <&xbar_amx1_in3>;
+							};
+						};
+
+						port@3 {
+							reg = <3>;
+
+							amx1_in4: endpoint {
+								remote-endpoint = <&xbar_amx1_in4>;
+							};
+						};
+
+						amx1_out_port: port@4 {
+							reg = <4>;
+
+							amx1_out: endpoint {
+								remote-endpoint = <&xbar_amx1_out>;
+							};
+						};
+					};
+				};
+
+				amx@2903100 {
+					status = "okay";
+
+					ports {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						port@0 {
+							reg = <0>;
+
+							amx2_in1: endpoint {
+								remote-endpoint = <&xbar_amx2_in1>;
+							};
+						};
+
+						port@1 {
+							reg = <1>;
+
+							amx2_in2: endpoint {
+								remote-endpoint = <&xbar_amx2_in2>;
+							};
+						};
+
+						port@2 {
+							reg = <2>;
+
+							amx2_in3: endpoint {
+								remote-endpoint = <&xbar_amx2_in3>;
+							};
+						};
+
+						port@3 {
+							reg = <3>;
+
+							amx2_in4: endpoint {
+								remote-endpoint = <&xbar_amx2_in4>;
+							};
+						};
+
+						amx2_out_port: port@4 {
+							reg = <4>;
+
+							amx2_out: endpoint {
+								remote-endpoint = <&xbar_amx2_out>;
+							};
+						};
+					};
+				};
+
+				amx@2903200 {
+					status = "okay";
+
+					ports {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						port@0 {
+							reg = <0>;
+
+							amx3_in1: endpoint {
+								remote-endpoint = <&xbar_amx3_in1>;
+							};
+						};
+
+						port@1 {
+							reg = <1>;
+
+							amx3_in2: endpoint {
+								remote-endpoint = <&xbar_amx3_in2>;
+							};
+						};
+
+						port@2 {
+							reg = <2>;
+
+							amx3_in3: endpoint {
+								remote-endpoint = <&xbar_amx3_in3>;
+							};
+						};
+
+						port@3 {
+							reg = <3>;
+
+							amx3_in4: endpoint {
+								remote-endpoint = <&xbar_amx3_in4>;
+							};
+						};
+
+						amx3_out_port: port@4 {
+							reg = <4>;
+
+							amx3_out: endpoint {
+								remote-endpoint = <&xbar_amx3_out>;
+							};
+						};
+					};
+				};
+
+				amx@2903300 {
+					status = "okay";
+
+					ports {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						port@0 {
+							reg = <0>;
+
+							amx4_in1: endpoint {
+								remote-endpoint = <&xbar_amx4_in1>;
+							};
+						};
+
+						port@1 {
+							reg = <1>;
+
+							amx4_in2: endpoint {
+								remote-endpoint = <&xbar_amx4_in2>;
+							};
+						};
+
+						port@2 {
+							reg = <2>;
+
+							amx4_in3: endpoint {
+								remote-endpoint = <&xbar_amx4_in3>;
+							};
+						};
+
+						port@3 {
+							reg = <3>;
+
+							amx4_in4: endpoint {
+								remote-endpoint = <&xbar_amx4_in4>;
+							};
+						};
+
+						amx4_out_port: port@4 {
+							reg = <4>;
+
+							amx4_out: endpoint {
+								remote-endpoint = <&xbar_amx4_out>;
+							};
+						};
+					};
+				};
+
+				adx@2903800 {
+					status = "okay";
+
+					ports {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						port@0 {
+							reg = <0>;
+
+							adx1_in: endpoint {
+								remote-endpoint = <&xbar_adx1_in>;
+							};
+						};
+
+						adx1_out1_port: port@1 {
+							reg = <1>;
+
+							adx1_out1: endpoint {
+								remote-endpoint = <&xbar_adx1_out1>;
+							};
+						};
+
+						adx1_out2_port: port@2 {
+							reg = <2>;
+
+							adx1_out2: endpoint {
+								remote-endpoint = <&xbar_adx1_out2>;
+							};
+						};
+
+						adx1_out3_port: port@3 {
+							reg = <3>;
+
+							adx1_out3: endpoint {
+								remote-endpoint = <&xbar_adx1_out3>;
+							};
+						};
+
+						adx1_out4_port: port@4 {
+							reg = <4>;
+
+							adx1_out4: endpoint {
+								remote-endpoint = <&xbar_adx1_out4>;
+							};
+						};
+					};
+				};
+
+				adx@2903900 {
+					status = "okay";
+
+					ports {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						port@0 {
+							reg = <0>;
+
+							adx2_in: endpoint {
+								remote-endpoint = <&xbar_adx2_in>;
+							};
+						};
+
+						adx2_out1_port: port@1 {
+							reg = <1>;
+
+							adx2_out1: endpoint {
+								remote-endpoint = <&xbar_adx2_out1>;
+							};
+						};
+
+						adx2_out2_port: port@2 {
+							reg = <2>;
+
+							adx2_out2: endpoint {
+								remote-endpoint = <&xbar_adx2_out2>;
+							};
+						};
+
+						adx2_out3_port: port@3 {
+							reg = <3>;
+
+							adx2_out3: endpoint {
+								remote-endpoint = <&xbar_adx2_out3>;
+							};
+						};
+
+						adx2_out4_port: port@4 {
+							reg = <4>;
+
+							adx2_out4: endpoint {
+								remote-endpoint = <&xbar_adx2_out4>;
+							};
+						};
+					};
+				};
+
+				adx@2903a00 {
+					status = "okay";
+
+					ports {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						port@0 {
+							reg = <0>;
+
+							adx3_in: endpoint {
+								remote-endpoint = <&xbar_adx3_in>;
+							};
+						};
+
+						adx3_out1_port: port@1 {
+							reg = <1>;
+
+							adx3_out1: endpoint {
+								remote-endpoint = <&xbar_adx3_out1>;
+							};
+						};
+
+						adx3_out2_port: port@2 {
+							reg = <2>;
+
+							adx3_out2: endpoint {
+								remote-endpoint = <&xbar_adx3_out2>;
+							};
+						};
+
+						adx3_out3_port: port@3 {
+							reg = <3>;
+
+							adx3_out3: endpoint {
+								remote-endpoint = <&xbar_adx3_out3>;
+							};
+						};
+
+						adx3_out4_port: port@4 {
+							reg = <4>;
+
+							adx3_out4: endpoint {
+								remote-endpoint = <&xbar_adx3_out4>;
+							};
+						};
+					};
+				};
+
+				adx@2903b00 {
+					status = "okay";
+
+					ports {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						port@0 {
+							reg = <0>;
+
+							adx4_in: endpoint {
+								remote-endpoint = <&xbar_adx4_in>;
+							};
+						};
+
+						adx4_out1_port: port@1 {
+							reg = <1>;
+
+							adx4_out1: endpoint {
+								remote-endpoint = <&xbar_adx4_out1>;
+							};
+						};
+
+						adx4_out2_port: port@2 {
+							reg = <2>;
+
+							adx4_out2: endpoint {
+								remote-endpoint = <&xbar_adx4_out2>;
+							};
+						};
+
+						adx4_out3_port: port@3 {
+							reg = <3>;
+
+							adx4_out3: endpoint {
+								remote-endpoint = <&xbar_adx4_out3>;
+							};
+						};
+
+						adx4_out4_port: port@4 {
+							reg = <4>;
+
+							adx4_out4: endpoint {
+								remote-endpoint = <&xbar_adx4_out4>;
+							};
+						};
+					};
+				};
+
+				dmic@2904200 {
+					status = "okay";
+
+					ports {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						port@0 {
+							reg = <0>;
+
+							dmic3_cif: endpoint {
+								remote-endpoint = <&xbar_dmic3>;
+							};
+						};
+
+						dmic3_port: port@1 {
+							reg = <1>;
+
+							dmic3_dap: endpoint {
+								/* placeholder for external codec */
+							};
+						};
+					};
+				};
+
+				processing-engine@2908000 {
+					status = "okay";
+
+					ports {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						port@0 {
+							reg = <0x0>;
+
+							ope1_cif_in_ep: endpoint {
+								remote-endpoint = <&xbar_ope1_in_ep>;
+							};
+						};
+
+						ope1_out_port: port@1 {
+							reg = <0x1>;
+
+							ope1_cif_out_ep: endpoint {
+								remote-endpoint = <&xbar_ope1_out_ep>;
+							};
+						};
+					};
+				};
+
+				mvc@290a000 {
+					status = "okay";
+
+					ports {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						port@0 {
+							reg = <0>;
+
+							mvc1_cif_in: endpoint {
+								remote-endpoint = <&xbar_mvc1_in>;
+							};
+						};
+
+						mvc1_out_port: port@1 {
+							reg = <1>;
+
+							mvc1_cif_out: endpoint {
+								remote-endpoint = <&xbar_mvc1_out>;
+							};
+						};
+					};
+				};
+
+				mvc@290a200 {
+					status = "okay";
+
+					ports {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						port@0 {
+							reg = <0>;
+
+							mvc2_cif_in: endpoint {
+								remote-endpoint = <&xbar_mvc2_in>;
+							};
+						};
+
+						mvc2_out_port: port@1 {
+							reg = <1>;
+
+							mvc2_cif_out: endpoint {
+								remote-endpoint = <&xbar_mvc2_out>;
+							};
+						};
+					};
+				};
+
+				amixer@290bb00 {
+					status = "okay";
+
+					ports {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						port@0 {
+							reg = <0x0>;
+
+							mix_in1: endpoint {
+								remote-endpoint = <&xbar_mix_in1>;
+							};
+						};
+
+						port@1 {
+							reg = <0x1>;
+
+							mix_in2: endpoint {
+								remote-endpoint = <&xbar_mix_in2>;
+							};
+						};
+
+						port@2 {
+							reg = <0x2>;
+
+							mix_in3: endpoint {
+								remote-endpoint = <&xbar_mix_in3>;
+							};
+						};
+
+						port@3 {
+							reg = <0x3>;
+
+							mix_in4: endpoint {
+								remote-endpoint = <&xbar_mix_in4>;
+							};
+						};
+
+						port@4 {
+							reg = <0x4>;
+
+							mix_in5: endpoint {
+								remote-endpoint = <&xbar_mix_in5>;
+							};
+						};
+
+						port@5 {
+							reg = <0x5>;
+
+							mix_in6: endpoint {
+								remote-endpoint = <&xbar_mix_in6>;
+							};
+						};
+
+						port@6 {
+							reg = <0x6>;
+
+							mix_in7: endpoint {
+								remote-endpoint = <&xbar_mix_in7>;
+							};
+						};
+
+						port@7 {
+							reg = <0x7>;
+
+							mix_in8: endpoint {
+								remote-endpoint = <&xbar_mix_in8>;
+							};
+						};
+
+						port@8 {
+							reg = <0x8>;
+
+							mix_in9: endpoint {
+								remote-endpoint = <&xbar_mix_in9>;
+							};
+						};
+
+						port@9 {
+							reg = <0x9>;
+
+							mix_in10: endpoint {
+								remote-endpoint = <&xbar_mix_in10>;
+							};
+						};
+
+						mix_out1_port: port@a {
+							reg = <0xa>;
+
+							mix_out1: endpoint {
+								remote-endpoint = <&xbar_mix_out1>;
+							};
+						};
+
+						mix_out2_port: port@b {
+							reg = <0xb>;
+
+							mix_out2: endpoint {
+								remote-endpoint = <&xbar_mix_out2>;
+							};
+						};
+
+						mix_out3_port: port@c {
+							reg = <0xc>;
+
+							mix_out3: endpoint {
+								remote-endpoint = <&xbar_mix_out3>;
+							};
+						};
+
+						mix_out4_port: port@d {
+							reg = <0xd>;
+
+							mix_out4: endpoint {
+								remote-endpoint = <&xbar_mix_out4>;
+							};
+						};
+
+						mix_out5_port: port@e {
+							reg = <0xe>;
+
+							mix_out5: endpoint {
+								remote-endpoint = <&xbar_mix_out5>;
+							};
+						};
+					};
+				};
+
+				admaif@290f000 {
+					status = "okay";
+
+					ports {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						admaif0_port: port@0 {
+							reg = <0x0>;
+
+							admaif0: endpoint {
+								remote-endpoint = <&xbar_admaif0>;
+							};
+						};
+
+						admaif1_port: port@1 {
+							reg = <0x1>;
+
+							admaif1: endpoint {
+								remote-endpoint = <&xbar_admaif1>;
+							};
+						};
+
+						admaif2_port: port@2 {
+							reg = <0x2>;
+
+							admaif2: endpoint {
+								remote-endpoint = <&xbar_admaif2>;
+							};
+						};
+
+						admaif3_port: port@3 {
+							reg = <0x3>;
+
+							admaif3: endpoint {
+								remote-endpoint = <&xbar_admaif3>;
+							};
+						};
+
+						admaif4_port: port@4 {
+							reg = <0x4>;
+
+							admaif4: endpoint {
+								remote-endpoint = <&xbar_admaif4>;
+							};
+						};
+
+						admaif5_port: port@5 {
+							reg = <0x5>;
+
+							admaif5: endpoint {
+								remote-endpoint = <&xbar_admaif5>;
+							};
+						};
+
+						admaif6_port: port@6 {
+							reg = <0x6>;
+
+							admaif6: endpoint {
+								remote-endpoint = <&xbar_admaif6>;
+							};
+						};
+
+						admaif7_port: port@7 {
+							reg = <0x7>;
+
+							admaif7: endpoint {
+								remote-endpoint = <&xbar_admaif7>;
+							};
+						};
+
+						admaif8_port: port@8 {
+							reg = <0x8>;
+
+							admaif8: endpoint {
+								remote-endpoint = <&xbar_admaif8>;
+							};
+						};
+
+						admaif9_port: port@9 {
+							reg = <0x9>;
+
+							admaif9: endpoint {
+								remote-endpoint = <&xbar_admaif9>;
+							};
+						};
+
+						admaif10_port: port@a {
+							reg = <0xa>;
+
+							admaif10: endpoint {
+								remote-endpoint = <&xbar_admaif10>;
+							};
+						};
+
+						admaif11_port: port@b {
+							reg = <0xb>;
+
+							admaif11: endpoint {
+								remote-endpoint = <&xbar_admaif11>;
+							};
+						};
+
+						admaif12_port: port@c {
+							reg = <0xc>;
+
+							admaif12: endpoint {
+								remote-endpoint = <&xbar_admaif12>;
+							};
+						};
+
+						admaif13_port: port@d {
+							reg = <0xd>;
+
+							admaif13: endpoint {
+								remote-endpoint = <&xbar_admaif13>;
+							};
+						};
+
+						admaif14_port: port@e {
+							reg = <0xe>;
+
+							admaif14: endpoint {
+								remote-endpoint = <&xbar_admaif14>;
+							};
+						};
+
+						admaif15_port: port@f {
+							reg = <0xf>;
+
+							admaif15: endpoint {
+								remote-endpoint = <&xbar_admaif15>;
+							};
+						};
+
+						admaif16_port: port@10 {
+							reg = <0x10>;
+
+							admaif16: endpoint {
+								remote-endpoint = <&xbar_admaif16>;
+							};
+						};
+
+						admaif17_port: port@11 {
+							reg = <0x11>;
+
+							admaif17: endpoint {
+								remote-endpoint = <&xbar_admaif17>;
+							};
+						};
+
+						admaif18_port: port@12 {
+							reg = <0x12>;
+
+							admaif18: endpoint {
+								remote-endpoint = <&xbar_admaif18>;
+							};
+						};
+
+						admaif19_port: port@13 {
+							reg = <0x13>;
+
+							admaif19: endpoint {
+								remote-endpoint = <&xbar_admaif19>;
+							};
+						};
+					};
+				};
+
+				asrc@2910000 {
+					status = "okay";
+
+					ports {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						port@0 {
+							reg = <0x0>;
+
+							asrc_in1_ep: endpoint {
+								remote-endpoint = <&xbar_asrc_in1_ep>;
+							};
+						};
+
+						port@1 {
+							reg = <0x1>;
+
+							asrc_in2_ep: endpoint {
+								remote-endpoint = <&xbar_asrc_in2_ep>;
+							};
+						};
+
+						port@2 {
+							reg = <0x2>;
+
+							asrc_in3_ep: endpoint {
+								remote-endpoint = <&xbar_asrc_in3_ep>;
+							};
+						};
+
+						port@3 {
+							reg = <0x3>;
+
+							asrc_in4_ep: endpoint {
+								remote-endpoint = <&xbar_asrc_in4_ep>;
+							};
+						};
+
+						port@4 {
+							reg = <0x4>;
+
+							asrc_in5_ep: endpoint {
+								remote-endpoint = <&xbar_asrc_in5_ep>;
+							};
+						};
+
+						port@5 {
+							reg = <0x5>;
+
+							asrc_in6_ep: endpoint {
+								remote-endpoint = <&xbar_asrc_in6_ep>;
+							};
+						};
+
+						port@6 {
+							reg = <0x6>;
+
+							asrc_in7_ep: endpoint {
+								remote-endpoint = <&xbar_asrc_in7_ep>;
+							};
+						};
+
+						asrc_out1_port: port@7 {
+							reg = <0x7>;
+
+							asrc_out1_ep: endpoint {
+								remote-endpoint = <&xbar_asrc_out1_ep>;
+							};
+						};
+
+						asrc_out2_port: port@8 {
+							reg = <0x8>;
+
+							asrc_out2_ep: endpoint {
+								remote-endpoint = <&xbar_asrc_out2_ep>;
+							};
+						};
+
+						asrc_out3_port: port@9 {
+							reg = <0x9>;
+
+							asrc_out3_ep: endpoint {
+								remote-endpoint = <&xbar_asrc_out3_ep>;
+							};
+						};
+
+						asrc_out4_port: port@a {
+							reg = <0xa>;
+
+							asrc_out4_ep: endpoint {
+								remote-endpoint = <&xbar_asrc_out4_ep>;
+							};
+						};
+
+						asrc_out5_port: port@b {
+							reg = <0xb>;
+
+							asrc_out5_ep: endpoint {
+								remote-endpoint = <&xbar_asrc_out5_ep>;
+							};
+						};
+
+						asrc_out6_port:	port@c {
+							reg = <0xc>;
+
+							asrc_out6_ep: endpoint {
+								remote-endpoint = <&xbar_asrc_out6_ep>;
+							};
+						};
+					};
+				};
+			};
+
+			dma-controller@2930000 {
+				status = "okay";
+			};
+
+			interrupt-controller@2a40000 {
+				status = "okay";
+			};
+		};
+
+		serial@3100000 {
+			compatible = "nvidia,tegra194-hsuart";
+			status = "okay";
+		};
+
+		hda@3510000 {
+			nvidia,model = "NVIDIA Jetson AGX Orin HDA";
+			status = "okay";
+		};
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8";
+		stdout-path = "serial0:115200n8";
+	};
+
+	bus@0 {
+		ethernet@6800000 {
+			status = "okay";
+
+			phy-handle = <&mgbe0_phy>;
+			phy-mode = "usxgmii";
+
+			mdio {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				mgbe0_phy: phy@0 {
+					compatible = "ethernet-phy-ieee802.3-c45";
+					reg = <0x0>;
+
+					#phy-cells = <0>;
+				};
+			};
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		status = "okay";
+
+		key-force-recovery {
+			label = "Force Recovery";
+			gpios = <&gpio TEGRA234_MAIN_GPIO(G, 0) GPIO_ACTIVE_LOW>;
+			linux,input-type = <EV_KEY>;
+			linux,code = <BTN_1>;
+		};
+
+		key-power {
+			label = "Power";
+			gpios = <&gpio_aon TEGRA234_AON_GPIO(EE, 4) GPIO_ACTIVE_LOW>;
+			linux,input-type = <EV_KEY>;
+			linux,code = <KEY_POWER>;
+			wakeup-event-action = <EV_ACT_ASSERTED>;
+			wakeup-source;
+		};
+
+		key-suspend {
+			label = "Suspend";
+			gpios = <&gpio TEGRA234_MAIN_GPIO(G, 2) GPIO_ACTIVE_LOW>;
+			linux,input-type = <EV_KEY>;
+			linux,code = <KEY_SLEEP>;
+		};
+	};
+
+	serial {
+		status = "okay";
+	};
+
+	sound {
+		status = "okay";
+
+		compatible = "nvidia,tegra186-audio-graph-card";
+
+		dais = /* ADMAIF (FE) Ports */
+		       <&admaif0_port>, <&admaif1_port>, <&admaif2_port>, <&admaif3_port>,
+		       <&admaif4_port>, <&admaif5_port>, <&admaif6_port>, <&admaif7_port>,
+		       <&admaif8_port>, <&admaif9_port>, <&admaif10_port>, <&admaif11_port>,
+		       <&admaif12_port>, <&admaif13_port>, <&admaif14_port>, <&admaif15_port>,
+		       <&admaif16_port>, <&admaif17_port>, <&admaif18_port>, <&admaif19_port>,
+		       /* XBAR Ports */
+		       <&xbar_i2s1_port>, <&xbar_i2s2_port>, <&xbar_i2s4_port>,
+		       <&xbar_i2s6_port>, <&xbar_dmic3_port>,
+		       <&xbar_sfc1_in_port>, <&xbar_sfc2_in_port>,
+		       <&xbar_sfc3_in_port>, <&xbar_sfc4_in_port>,
+		       <&xbar_mvc1_in_port>, <&xbar_mvc2_in_port>,
+		       <&xbar_amx1_in1_port>, <&xbar_amx1_in2_port>,
+		       <&xbar_amx1_in3_port>, <&xbar_amx1_in4_port>,
+		       <&xbar_amx2_in1_port>, <&xbar_amx2_in2_port>,
+		       <&xbar_amx2_in3_port>, <&xbar_amx2_in4_port>,
+		       <&xbar_amx3_in1_port>, <&xbar_amx3_in2_port>,
+		       <&xbar_amx3_in3_port>, <&xbar_amx3_in4_port>,
+		       <&xbar_amx4_in1_port>, <&xbar_amx4_in2_port>,
+		       <&xbar_amx4_in3_port>, <&xbar_amx4_in4_port>,
+		       <&xbar_adx1_in_port>, <&xbar_adx2_in_port>,
+		       <&xbar_adx3_in_port>, <&xbar_adx4_in_port>,
+		       <&xbar_mix_in1_port>, <&xbar_mix_in2_port>,
+		       <&xbar_mix_in3_port>, <&xbar_mix_in4_port>,
+		       <&xbar_mix_in5_port>, <&xbar_mix_in6_port>,
+		       <&xbar_mix_in7_port>, <&xbar_mix_in8_port>,
+		       <&xbar_mix_in9_port>, <&xbar_mix_in10_port>,
+		       <&xbar_asrc_in1_port>, <&xbar_asrc_in2_port>,
+		       <&xbar_asrc_in3_port>, <&xbar_asrc_in4_port>,
+		       <&xbar_asrc_in5_port>, <&xbar_asrc_in6_port>,
+		       <&xbar_asrc_in7_port>,
+		       <&xbar_ope1_in_port>,
+		       /* HW accelerators */
+		       <&sfc1_out_port>, <&sfc2_out_port>,
+		       <&sfc3_out_port>, <&sfc4_out_port>,
+		       <&mvc1_out_port>, <&mvc2_out_port>,
+		       <&amx1_out_port>, <&amx2_out_port>,
+		       <&amx3_out_port>, <&amx4_out_port>,
+		       <&adx1_out1_port>, <&adx1_out2_port>,
+		       <&adx1_out3_port>, <&adx1_out4_port>,
+		       <&adx2_out1_port>, <&adx2_out2_port>,
+		       <&adx2_out3_port>, <&adx2_out4_port>,
+		       <&adx3_out1_port>, <&adx3_out2_port>,
+		       <&adx3_out3_port>, <&adx3_out4_port>,
+		       <&adx4_out1_port>, <&adx4_out2_port>,
+		       <&adx4_out3_port>, <&adx4_out4_port>,
+		       <&mix_out1_port>, <&mix_out2_port>, <&mix_out3_port>,
+		       <&mix_out4_port>, <&mix_out5_port>,
+		       <&asrc_out1_port>, <&asrc_out2_port>, <&asrc_out3_port>,
+		       <&asrc_out4_port>, <&asrc_out5_port>, <&asrc_out6_port>,
+		       <&ope1_out_port>,
+		       /* BE I/O Ports */
+		       <&i2s1_port>, <&i2s2_port>, <&i2s4_port>, <&i2s6_port>,
+		       <&dmic3_port>;
+
+		label = "NVIDIA Jetson AGX Orin APE";
+	};
+
+	pcie@14100000 {
+		status = "okay";
+
+		vddio-pex-ctl-supply = <&vdd_1v8_ao>;
+
+		phys = <&p2u_hsio_3>;
+		phy-names = "p2u-0";
+	};
+
+	pcie@14160000 {
+		status = "okay";
+
+		vddio-pex-ctl-supply = <&vdd_1v8_ao>;
+
+		phys = <&p2u_hsio_4>, <&p2u_hsio_5>, <&p2u_hsio_6>,
+		       <&p2u_hsio_7>;
+		phy-names = "p2u-0", "p2u-1", "p2u-2", "p2u-3";
+	};
+
+	pcie@141a0000 {
+		status = "okay";
+
+		vddio-pex-ctl-supply = <&vdd_1v8_ls>;
+		vpcie3v3-supply = <&vdd_3v3_pcie>;
+		vpcie12v-supply = <&vdd_12v_pcie>;
+
+		phys = <&p2u_nvhs_0>, <&p2u_nvhs_1>, <&p2u_nvhs_2>,
+		       <&p2u_nvhs_3>, <&p2u_nvhs_4>, <&p2u_nvhs_5>,
+		       <&p2u_nvhs_6>, <&p2u_nvhs_7>;
+		phy-names = "p2u-0", "p2u-1", "p2u-2", "p2u-3", "p2u-4",
+			    "p2u-5", "p2u-6", "p2u-7";
+	};
+
+	pcie-ep@141a0000 {
+		status = "disabled";
+
+		vddio-pex-ctl-supply = <&vdd_1v8_ls>;
+
+		reset-gpios = <&gpio TEGRA234_MAIN_GPIO(AF, 1) GPIO_ACTIVE_LOW>;
+
+		nvidia,refclk-select-gpios = <&gpio_aon
+					      TEGRA234_AON_GPIO(AA, 4)
+					      GPIO_ACTIVE_HIGH>;
+
+		phys = <&p2u_nvhs_0>, <&p2u_nvhs_1>, <&p2u_nvhs_2>,
+		       <&p2u_nvhs_3>, <&p2u_nvhs_4>, <&p2u_nvhs_5>,
+		       <&p2u_nvhs_6>, <&p2u_nvhs_7>;
+		phy-names = "p2u-0", "p2u-1", "p2u-2", "p2u-3", "p2u-4",
+			    "p2u-5", "p2u-6", "p2u-7";
+	};
+};
diff --git a/arch/arm64/boot/dts/nvidia/tegra234-p3737-0000.dtsi b/arch/arm64/boot/dts/nvidia/tegra234-p3737-0000.dtsi
new file mode 100644
index 000000000000..a85993c85e45
--- /dev/null
+++ b/arch/arm64/boot/dts/nvidia/tegra234-p3737-0000.dtsi
@@ -0,0 +1,5 @@
+// SPDX-License-Identifier: GPL-2.0
+
+/ {
+	compatible = "nvidia,p3737-0000";
+};
diff --git a/arch/arm64/boot/dts/nvidia/tegra234-sim-vdk.dts b/arch/arm64/boot/dts/nvidia/tegra234-sim-vdk.dts
index b5d9a5526272..5804acfc428a 100644
--- a/arch/arm64/boot/dts/nvidia/tegra234-sim-vdk.dts
+++ b/arch/arm64/boot/dts/nvidia/tegra234-sim-vdk.dts
@@ -26,7 +26,6 @@
 			status = "okay";
 			bus-width = <8>;
 			non-removable;
-			only-1-8-v;
 		};
 
 		rtc@c2a0000 {
diff --git a/arch/arm64/boot/dts/nvidia/tegra234.dtsi b/arch/arm64/boot/dts/nvidia/tegra234.dtsi
index f0efb3a62804..0170bfa8a467 100644
--- a/arch/arm64/boot/dts/nvidia/tegra234.dtsi
+++ b/arch/arm64/boot/dts/nvidia/tegra234.dtsi
@@ -1,8 +1,11 @@
 // SPDX-License-Identifier: GPL-2.0
 
 #include <dt-bindings/clock/tegra234-clock.h>
+#include <dt-bindings/gpio/tegra234-gpio.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/mailbox/tegra186-hsp.h>
+#include <dt-bindings/memory/tegra234-mc.h>
+#include <dt-bindings/power/tegra234-powergate.h>
 #include <dt-bindings/reset/tegra234-reset.h>
 
 / {
@@ -18,6 +21,497 @@
 
 		ranges = <0x0 0x0 0x0 0x40000000>;
 
+		gpcdma: dma-controller@2600000 {
+			compatible = "nvidia,tegra234-gpcdma",
+				     "nvidia,tegra186-gpcdma";
+			reg = <0x2600000 0x210000>;
+			resets = <&bpmp TEGRA234_RESET_GPCDMA>;
+			reset-names = "gpcdma";
+			interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>;
+			#dma-cells = <1>;
+			iommus = <&smmu_niso0 TEGRA234_SID_GPCDMA>;
+			dma-coherent;
+		};
+
+		aconnect@2900000 {
+			compatible = "nvidia,tegra234-aconnect",
+				     "nvidia,tegra210-aconnect";
+			clocks = <&bpmp TEGRA234_CLK_APE>,
+				 <&bpmp TEGRA234_CLK_APB2APE>;
+			clock-names = "ape", "apb2ape";
+			power-domains = <&bpmp TEGRA234_POWER_DOMAIN_AUD>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x02900000 0x02900000 0x200000>;
+			status = "disabled";
+
+			tegra_ahub: ahub@2900800 {
+				compatible = "nvidia,tegra234-ahub";
+				reg = <0x02900800 0x800>;
+				clocks = <&bpmp TEGRA234_CLK_AHUB>;
+				clock-names = "ahub";
+				assigned-clocks = <&bpmp TEGRA234_CLK_AHUB>;
+				assigned-clock-parents = <&bpmp TEGRA234_CLK_PLLA_OUT0>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x02900800 0x02900800 0x11800>;
+				status = "disabled";
+
+				tegra_i2s1: i2s@2901000 {
+					compatible = "nvidia,tegra234-i2s",
+						     "nvidia,tegra210-i2s";
+					reg = <0x2901000 0x100>;
+					clocks = <&bpmp TEGRA234_CLK_I2S1>,
+						 <&bpmp TEGRA234_CLK_I2S1_SYNC_INPUT>;
+					clock-names = "i2s", "sync_input";
+					assigned-clocks = <&bpmp TEGRA234_CLK_I2S1>;
+					assigned-clock-parents = <&bpmp TEGRA234_CLK_PLLA_OUT0>;
+					assigned-clock-rates = <1536000>;
+					sound-name-prefix = "I2S1";
+					status = "disabled";
+				};
+
+				tegra_i2s2: i2s@2901100 {
+					compatible = "nvidia,tegra234-i2s",
+						     "nvidia,tegra210-i2s";
+					reg = <0x2901100 0x100>;
+					clocks = <&bpmp TEGRA234_CLK_I2S2>,
+						 <&bpmp TEGRA234_CLK_I2S2_SYNC_INPUT>;
+					clock-names = "i2s", "sync_input";
+					assigned-clocks = <&bpmp TEGRA234_CLK_I2S2>;
+					assigned-clock-parents = <&bpmp TEGRA234_CLK_PLLA_OUT0>;
+					assigned-clock-rates = <1536000>;
+					sound-name-prefix = "I2S2";
+					status = "disabled";
+				};
+
+				tegra_i2s3: i2s@2901200 {
+					compatible = "nvidia,tegra234-i2s",
+						     "nvidia,tegra210-i2s";
+					reg = <0x2901200 0x100>;
+					clocks = <&bpmp TEGRA234_CLK_I2S3>,
+						 <&bpmp TEGRA234_CLK_I2S3_SYNC_INPUT>;
+					clock-names = "i2s", "sync_input";
+					assigned-clocks = <&bpmp TEGRA234_CLK_I2S3>;
+					assigned-clock-parents = <&bpmp TEGRA234_CLK_PLLA_OUT0>;
+					assigned-clock-rates = <1536000>;
+					sound-name-prefix = "I2S3";
+					status = "disabled";
+				};
+
+				tegra_i2s4: i2s@2901300 {
+					compatible = "nvidia,tegra234-i2s",
+						     "nvidia,tegra210-i2s";
+					reg = <0x2901300 0x100>;
+					clocks = <&bpmp TEGRA234_CLK_I2S4>,
+						 <&bpmp TEGRA234_CLK_I2S4_SYNC_INPUT>;
+					clock-names = "i2s", "sync_input";
+					assigned-clocks = <&bpmp TEGRA234_CLK_I2S4>;
+					assigned-clock-parents = <&bpmp TEGRA234_CLK_PLLA_OUT0>;
+					assigned-clock-rates = <1536000>;
+					sound-name-prefix = "I2S4";
+					status = "disabled";
+				};
+
+				tegra_i2s5: i2s@2901400 {
+					compatible = "nvidia,tegra234-i2s",
+						     "nvidia,tegra210-i2s";
+					reg = <0x2901400 0x100>;
+					clocks = <&bpmp TEGRA234_CLK_I2S5>,
+						 <&bpmp TEGRA234_CLK_I2S5_SYNC_INPUT>;
+					clock-names = "i2s", "sync_input";
+					assigned-clocks = <&bpmp TEGRA234_CLK_I2S5>;
+					assigned-clock-parents = <&bpmp TEGRA234_CLK_PLLA_OUT0>;
+					assigned-clock-rates = <1536000>;
+					sound-name-prefix = "I2S5";
+					status = "disabled";
+				};
+
+				tegra_i2s6: i2s@2901500 {
+					compatible = "nvidia,tegra234-i2s",
+						     "nvidia,tegra210-i2s";
+					reg = <0x2901500 0x100>;
+					clocks = <&bpmp TEGRA234_CLK_I2S6>,
+						 <&bpmp TEGRA234_CLK_I2S6_SYNC_INPUT>;
+					clock-names = "i2s", "sync_input";
+					assigned-clocks = <&bpmp TEGRA234_CLK_I2S6>;
+					assigned-clock-parents = <&bpmp TEGRA234_CLK_PLLA_OUT0>;
+					assigned-clock-rates = <1536000>;
+					sound-name-prefix = "I2S6";
+					status = "disabled";
+				};
+
+				tegra_sfc1: sfc@2902000 {
+					compatible = "nvidia,tegra234-sfc",
+						     "nvidia,tegra210-sfc";
+					reg = <0x2902000 0x200>;
+					sound-name-prefix = "SFC1";
+					status = "disabled";
+				};
+
+				tegra_sfc2: sfc@2902200 {
+					compatible = "nvidia,tegra234-sfc",
+						     "nvidia,tegra210-sfc";
+					reg = <0x2902200 0x200>;
+					sound-name-prefix = "SFC2";
+					status = "disabled";
+				};
+
+				tegra_sfc3: sfc@2902400 {
+					compatible = "nvidia,tegra234-sfc",
+						     "nvidia,tegra210-sfc";
+					reg = <0x2902400 0x200>;
+					sound-name-prefix = "SFC3";
+					status = "disabled";
+				};
+
+				tegra_sfc4: sfc@2902600 {
+					compatible = "nvidia,tegra234-sfc",
+						     "nvidia,tegra210-sfc";
+					reg = <0x2902600 0x200>;
+					sound-name-prefix = "SFC4";
+					status = "disabled";
+				};
+
+				tegra_amx1: amx@2903000 {
+					compatible = "nvidia,tegra234-amx",
+						     "nvidia,tegra194-amx";
+					reg = <0x2903000 0x100>;
+					sound-name-prefix = "AMX1";
+					status = "disabled";
+				};
+
+				tegra_amx2: amx@2903100 {
+					compatible = "nvidia,tegra234-amx",
+						     "nvidia,tegra194-amx";
+					reg = <0x2903100 0x100>;
+					sound-name-prefix = "AMX2";
+					status = "disabled";
+				};
+
+				tegra_amx3: amx@2903200 {
+					compatible = "nvidia,tegra234-amx",
+						     "nvidia,tegra194-amx";
+					reg = <0x2903200 0x100>;
+					sound-name-prefix = "AMX3";
+					status = "disabled";
+				};
+
+				tegra_amx4: amx@2903300 {
+					compatible = "nvidia,tegra234-amx",
+						     "nvidia,tegra194-amx";
+					reg = <0x2903300 0x100>;
+					sound-name-prefix = "AMX4";
+					status = "disabled";
+				};
+
+				tegra_adx1: adx@2903800 {
+					compatible = "nvidia,tegra234-adx",
+						     "nvidia,tegra210-adx";
+					reg = <0x2903800 0x100>;
+					sound-name-prefix = "ADX1";
+					status = "disabled";
+				};
+
+				tegra_adx2: adx@2903900 {
+					compatible = "nvidia,tegra234-adx",
+						     "nvidia,tegra210-adx";
+					reg = <0x2903900 0x100>;
+					sound-name-prefix = "ADX2";
+					status = "disabled";
+				};
+
+				tegra_adx3: adx@2903a00 {
+					compatible = "nvidia,tegra234-adx",
+						     "nvidia,tegra210-adx";
+					reg = <0x2903a00 0x100>;
+					sound-name-prefix = "ADX3";
+					status = "disabled";
+				};
+
+				tegra_adx4: adx@2903b00 {
+					compatible = "nvidia,tegra234-adx",
+						     "nvidia,tegra210-adx";
+					reg = <0x2903b00 0x100>;
+					sound-name-prefix = "ADX4";
+					status = "disabled";
+				};
+
+
+				tegra_dmic1: dmic@2904000 {
+					compatible = "nvidia,tegra234-dmic",
+						     "nvidia,tegra210-dmic";
+					reg = <0x2904000 0x100>;
+					clocks = <&bpmp TEGRA234_CLK_DMIC1>;
+					clock-names = "dmic";
+					assigned-clocks = <&bpmp TEGRA234_CLK_DMIC1>;
+					assigned-clock-parents = <&bpmp TEGRA234_CLK_PLLA_OUT0>;
+					assigned-clock-rates = <3072000>;
+					sound-name-prefix = "DMIC1";
+					status = "disabled";
+				};
+
+				tegra_dmic2: dmic@2904100 {
+					compatible = "nvidia,tegra234-dmic",
+						     "nvidia,tegra210-dmic";
+					reg = <0x2904100 0x100>;
+					clocks = <&bpmp TEGRA234_CLK_DMIC2>;
+					clock-names = "dmic";
+					assigned-clocks = <&bpmp TEGRA234_CLK_DMIC2>;
+					assigned-clock-parents = <&bpmp TEGRA234_CLK_PLLA_OUT0>;
+					assigned-clock-rates = <3072000>;
+					sound-name-prefix = "DMIC2";
+					status = "disabled";
+				};
+
+				tegra_dmic3: dmic@2904200 {
+					compatible = "nvidia,tegra234-dmic",
+						     "nvidia,tegra210-dmic";
+					reg = <0x2904200 0x100>;
+					clocks = <&bpmp TEGRA234_CLK_DMIC3>;
+					clock-names = "dmic";
+					assigned-clocks = <&bpmp TEGRA234_CLK_DMIC3>;
+					assigned-clock-parents = <&bpmp TEGRA234_CLK_PLLA_OUT0>;
+					assigned-clock-rates = <3072000>;
+					sound-name-prefix = "DMIC3";
+					status = "disabled";
+				};
+
+				tegra_dmic4: dmic@2904300 {
+					compatible = "nvidia,tegra234-dmic",
+						     "nvidia,tegra210-dmic";
+					reg = <0x2904300 0x100>;
+					clocks = <&bpmp TEGRA234_CLK_DMIC4>;
+					clock-names = "dmic";
+					assigned-clocks = <&bpmp TEGRA234_CLK_DMIC4>;
+					assigned-clock-parents = <&bpmp TEGRA234_CLK_PLLA_OUT0>;
+					assigned-clock-rates = <3072000>;
+					sound-name-prefix = "DMIC4";
+					status = "disabled";
+				};
+
+				tegra_dspk1: dspk@2905000 {
+					compatible = "nvidia,tegra234-dspk",
+						     "nvidia,tegra186-dspk";
+					reg = <0x2905000 0x100>;
+					clocks = <&bpmp TEGRA234_CLK_DSPK1>;
+					clock-names = "dspk";
+					assigned-clocks = <&bpmp TEGRA234_CLK_DSPK1>;
+					assigned-clock-parents = <&bpmp TEGRA234_CLK_PLLA_OUT0>;
+					assigned-clock-rates = <12288000>;
+					sound-name-prefix = "DSPK1";
+					status = "disabled";
+				};
+
+				tegra_dspk2: dspk@2905100 {
+					compatible = "nvidia,tegra234-dspk",
+						     "nvidia,tegra186-dspk";
+					reg = <0x2905100 0x100>;
+					clocks = <&bpmp TEGRA234_CLK_DSPK2>;
+					clock-names = "dspk";
+					assigned-clocks = <&bpmp TEGRA234_CLK_DSPK2>;
+					assigned-clock-parents = <&bpmp TEGRA234_CLK_PLLA_OUT0>;
+					assigned-clock-rates = <12288000>;
+					sound-name-prefix = "DSPK2";
+					status = "disabled";
+				};
+
+				tegra_ope1: processing-engine@2908000 {
+					compatible = "nvidia,tegra234-ope",
+						     "nvidia,tegra210-ope";
+					reg = <0x2908000 0x100>;
+					#address-cells = <1>;
+					#size-cells = <1>;
+					ranges;
+					sound-name-prefix = "OPE1";
+					status = "disabled";
+
+					equalizer@2908100 {
+						compatible = "nvidia,tegra234-peq",
+							     "nvidia,tegra210-peq";
+						reg = <0x2908100 0x100>;
+					};
+
+					dynamic-range-compressor@2908200 {
+						compatible = "nvidia,tegra234-mbdrc",
+							     "nvidia,tegra210-mbdrc";
+						reg = <0x2908200 0x200>;
+					};
+				};
+
+				tegra_mvc1: mvc@290a000 {
+					compatible = "nvidia,tegra234-mvc",
+						     "nvidia,tegra210-mvc";
+					reg = <0x290a000 0x200>;
+					sound-name-prefix = "MVC1";
+					status = "disabled";
+				};
+
+				tegra_mvc2: mvc@290a200 {
+					compatible = "nvidia,tegra234-mvc",
+						     "nvidia,tegra210-mvc";
+					reg = <0x290a200 0x200>;
+					sound-name-prefix = "MVC2";
+					status = "disabled";
+				};
+
+				tegra_amixer: amixer@290bb00 {
+					compatible = "nvidia,tegra234-amixer",
+						     "nvidia,tegra210-amixer";
+					reg = <0x290bb00 0x800>;
+					sound-name-prefix = "MIXER1";
+					status = "disabled";
+				};
+
+				tegra_admaif: admaif@290f000 {
+					compatible = "nvidia,tegra234-admaif",
+						     "nvidia,tegra186-admaif";
+					reg = <0x0290f000 0x1000>;
+					dmas = <&adma 1>, <&adma 1>,
+					       <&adma 2>, <&adma 2>,
+					       <&adma 3>, <&adma 3>,
+					       <&adma 4>, <&adma 4>,
+					       <&adma 5>, <&adma 5>,
+					       <&adma 6>, <&adma 6>,
+					       <&adma 7>, <&adma 7>,
+					       <&adma 8>, <&adma 8>,
+					       <&adma 9>, <&adma 9>,
+					       <&adma 10>, <&adma 10>,
+					       <&adma 11>, <&adma 11>,
+					       <&adma 12>, <&adma 12>,
+					       <&adma 13>, <&adma 13>,
+					       <&adma 14>, <&adma 14>,
+					       <&adma 15>, <&adma 15>,
+					       <&adma 16>, <&adma 16>,
+					       <&adma 17>, <&adma 17>,
+					       <&adma 18>, <&adma 18>,
+					       <&adma 19>, <&adma 19>,
+					       <&adma 20>, <&adma 20>;
+					dma-names = "rx1", "tx1",
+						    "rx2", "tx2",
+						    "rx3", "tx3",
+						    "rx4", "tx4",
+						    "rx5", "tx5",
+						    "rx6", "tx6",
+						    "rx7", "tx7",
+						    "rx8", "tx8",
+						    "rx9", "tx9",
+						    "rx10", "tx10",
+						    "rx11", "tx11",
+						    "rx12", "tx12",
+						    "rx13", "tx13",
+						    "rx14", "tx14",
+						    "rx15", "tx15",
+						    "rx16", "tx16",
+						    "rx17", "tx17",
+						    "rx18", "tx18",
+						    "rx19", "tx19",
+						    "rx20", "tx20";
+					interconnects = <&mc TEGRA234_MEMORY_CLIENT_APEDMAR &emc>,
+							<&mc TEGRA234_MEMORY_CLIENT_APEDMAW &emc>;
+					interconnect-names = "dma-mem", "write";
+					iommus = <&smmu_niso0 TEGRA234_SID_APE>;
+					status = "disabled";
+				};
+
+				tegra_asrc: asrc@2910000 {
+					compatible = "nvidia,tegra234-asrc",
+						     "nvidia,tegra186-asrc";
+					reg = <0x2910000 0x2000>;
+					sound-name-prefix = "ASRC1";
+					status = "disabled";
+				};
+			};
+
+			adma: dma-controller@2930000 {
+				compatible = "nvidia,tegra234-adma",
+					     "nvidia,tegra186-adma";
+				reg = <0x02930000 0x20000>;
+				interrupt-parent = <&agic>;
+				interrupts =  <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
+					      <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>,
+					      <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>,
+					      <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
+					      <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
+					      <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>,
+					      <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>,
+					      <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,
+					      <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+					      <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
+					      <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,
+					      <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
+					      <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
+					      <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>,
+					      <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>,
+					      <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>,
+					      <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>,
+					      <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>,
+					      <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
+					      <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>,
+					      <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>,
+					      <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>,
+					      <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>,
+					      <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>,
+					      <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>,
+					      <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>,
+					      <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>,
+					      <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>,
+					      <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>,
+					      <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>,
+					      <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>,
+					      <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
+				#dma-cells = <1>;
+				clocks = <&bpmp TEGRA234_CLK_AHUB>;
+				clock-names = "d_audio";
+				status = "disabled";
+			};
+
+			agic: interrupt-controller@2a40000 {
+				compatible = "nvidia,tegra234-agic",
+					     "nvidia,tegra210-agic";
+				#interrupt-cells = <3>;
+				interrupt-controller;
+				reg = <0x02a41000 0x1000>,
+				      <0x02a42000 0x2000>;
+				interrupts = <GIC_SPI 145
+					      (GIC_CPU_MASK_SIMPLE(4) |
+					       IRQ_TYPE_LEVEL_HIGH)>;
+				clocks = <&bpmp TEGRA234_CLK_APE>;
+				clock-names = "clk";
+				status = "disabled";
+			};
+		};
+
 		misc@100000 {
 			compatible = "nvidia,tegra234-misc";
 			reg = <0x00100000 0xf000>,
@@ -25,6 +519,217 @@
 			status = "okay";
 		};
 
+		timer@2080000 {
+			compatible = "nvidia,tegra234-timer";
+			reg = <0x02080000 0x00121000>;
+			interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
+			status = "okay";
+		};
+
+		host1x@13e00000 {
+			compatible = "nvidia,tegra234-host1x";
+			reg = <0x13e00000 0x10000>,
+			      <0x13e10000 0x10000>,
+			      <0x13e40000 0x10000>;
+			reg-names = "common", "hypervisor", "vm";
+			interrupts = <GIC_SPI 448 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 449 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 450 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 451 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 452 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 453 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 454 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 455 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 263 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "syncpt0", "syncpt1", "syncpt2", "syncpt3", "syncpt4",
+					  "syncpt5", "syncpt6", "syncpt7", "host1x";
+			clocks = <&bpmp TEGRA234_CLK_HOST1X>;
+			clock-names = "host1x";
+
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			ranges = <0x15000000 0x15000000 0x01000000>;
+			interconnects = <&mc TEGRA234_MEMORY_CLIENT_HOST1XDMAR &emc>;
+			interconnect-names = "dma-mem";
+			iommus = <&smmu_niso1 TEGRA234_SID_HOST1X>;
+
+			/* Context isolation domains */
+			iommu-map = <0 &smmu_niso0 TEGRA234_SID_HOST1X_CTX0 1>,
+				    <1 &smmu_niso0 TEGRA234_SID_HOST1X_CTX1 1>,
+				    <2 &smmu_niso0 TEGRA234_SID_HOST1X_CTX2 1>,
+				    <3 &smmu_niso0 TEGRA234_SID_HOST1X_CTX3 1>,
+				    <4 &smmu_niso0 TEGRA234_SID_HOST1X_CTX4 1>,
+				    <5 &smmu_niso0 TEGRA234_SID_HOST1X_CTX5 1>,
+				    <6 &smmu_niso0 TEGRA234_SID_HOST1X_CTX6 1>,
+				    <7 &smmu_niso0 TEGRA234_SID_HOST1X_CTX7 1>,
+				    <8 &smmu_niso1 TEGRA234_SID_HOST1X_CTX0 1>,
+				    <9 &smmu_niso1 TEGRA234_SID_HOST1X_CTX1 1>,
+				    <10 &smmu_niso1 TEGRA234_SID_HOST1X_CTX2 1>,
+				    <11 &smmu_niso1 TEGRA234_SID_HOST1X_CTX3 1>,
+				    <12 &smmu_niso1 TEGRA234_SID_HOST1X_CTX4 1>,
+				    <13 &smmu_niso1 TEGRA234_SID_HOST1X_CTX5 1>,
+				    <14 &smmu_niso1 TEGRA234_SID_HOST1X_CTX6 1>,
+				    <15 &smmu_niso1 TEGRA234_SID_HOST1X_CTX7 1>;
+
+			vic@15340000 {
+				compatible = "nvidia,tegra234-vic";
+				reg = <0x15340000 0x00040000>;
+				interrupts = <GIC_SPI 206 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&bpmp TEGRA234_CLK_VIC>;
+				clock-names = "vic";
+				resets = <&bpmp TEGRA234_RESET_VIC>;
+				reset-names = "vic";
+
+				power-domains = <&bpmp TEGRA234_POWER_DOMAIN_VIC>;
+				interconnects = <&mc TEGRA234_MEMORY_CLIENT_VICSRD &emc>,
+						<&mc TEGRA234_MEMORY_CLIENT_VICSWR &emc>;
+				interconnect-names = "dma-mem", "write";
+				iommus = <&smmu_niso1 TEGRA234_SID_VIC>;
+				dma-coherent;
+			};
+		};
+
+		gpio: gpio@2200000 {
+			compatible = "nvidia,tegra234-gpio";
+			reg-names = "security", "gpio";
+			reg = <0x02200000 0x10000>,
+			      <0x02210000 0x10000>;
+			interrupts = <GIC_SPI 288 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 289 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 290 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 291 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 292 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 293 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 294 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 295 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 296 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 297 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 298 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 299 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 300 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 301 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 302 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 303 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 304 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 305 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 306 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 307 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 308 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 309 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 310 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 311 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 312 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 313 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 314 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 315 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 316 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 317 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 318 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 319 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 320 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 321 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 322 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 323 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 324 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 325 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 326 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 327 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 328 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 329 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 333 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 334 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 335 IRQ_TYPE_LEVEL_HIGH>;
+			#interrupt-cells = <2>;
+			interrupt-controller;
+			#gpio-cells = <2>;
+			gpio-controller;
+		};
+
+		mc: memory-controller@2c00000 {
+			compatible = "nvidia,tegra234-mc";
+			reg = <0x02c00000 0x10000>,   /* MC-SID */
+			      <0x02c10000 0x10000>,   /* MC Broadcast*/
+			      <0x02c20000 0x10000>,   /* MC0 */
+			      <0x02c30000 0x10000>,   /* MC1 */
+			      <0x02c40000 0x10000>,   /* MC2 */
+			      <0x02c50000 0x10000>,   /* MC3 */
+			      <0x02b80000 0x10000>,   /* MC4 */
+			      <0x02b90000 0x10000>,   /* MC5 */
+			      <0x02ba0000 0x10000>,   /* MC6 */
+			      <0x02bb0000 0x10000>,   /* MC7 */
+			      <0x01700000 0x10000>,   /* MC8 */
+			      <0x01710000 0x10000>,   /* MC9 */
+			      <0x01720000 0x10000>,   /* MC10 */
+			      <0x01730000 0x10000>,   /* MC11 */
+			      <0x01740000 0x10000>,   /* MC12 */
+			      <0x01750000 0x10000>,   /* MC13 */
+			      <0x01760000 0x10000>,   /* MC14 */
+			      <0x01770000 0x10000>;   /* MC15 */
+			reg-names = "sid", "broadcast", "ch0", "ch1", "ch2", "ch3",
+				    "ch4", "ch5", "ch6", "ch7", "ch8", "ch9", "ch10",
+				    "ch11", "ch12", "ch13", "ch14", "ch15";
+			interrupts = <GIC_SPI 223 IRQ_TYPE_LEVEL_HIGH>;
+			#interconnect-cells = <1>;
+			status = "okay";
+
+			#address-cells = <2>;
+			#size-cells = <2>;
+
+			ranges = <0x01700000 0x0 0x01700000 0x0 0x100000>,
+				 <0x02b80000 0x0 0x02b80000 0x0 0x040000>,
+				 <0x02c00000 0x0 0x02c00000 0x0 0x100000>;
+
+			/*
+			 * Bit 39 of addresses passing through the memory
+			 * controller selects the XBAR format used when memory
+			 * is accessed. This is used to transparently access
+			 * memory in the XBAR format used by the discrete GPU
+			 * (bit 39 set) or Tegra (bit 39 clear).
+			 *
+			 * As a consequence, the operating system must ensure
+			 * that bit 39 is never used implicitly, for example
+			 * via an I/O virtual address mapping of an IOMMU. If
+			 * devices require access to the XBAR switch, their
+			 * drivers must set this bit explicitly.
+			 *
+			 * Limit the DMA range for memory clients to [38:0].
+			 */
+			dma-ranges = <0x0 0x0 0x0 0x80 0x0>;
+
+			emc: external-memory-controller@2c60000 {
+				compatible = "nvidia,tegra234-emc";
+				reg = <0x0 0x02c60000 0x0 0x90000>,
+				      <0x0 0x01780000 0x0 0x80000>;
+				interrupts = <GIC_SPI 224 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&bpmp TEGRA234_CLK_EMC>;
+				clock-names = "emc";
+				status = "okay";
+
+				#interconnect-cells = <0>;
+
+				nvidia,bpmp = <&bpmp>;
+			};
+		};
+
 		uarta: serial@3100000 {
 			compatible = "nvidia,tegra234-uart", "nvidia,tegra20-uart";
 			reg = <0x03100000 0x10000>;
@@ -36,15 +741,204 @@
 			status = "disabled";
 		};
 
+		gen1_i2c: i2c@3160000 {
+			compatible = "nvidia,tegra194-i2c";
+			reg = <0x3160000 0x100>;
+			status = "disabled";
+			interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
+			clock-frequency = <400000>;
+			clocks = <&bpmp TEGRA234_CLK_I2C1
+				  &bpmp TEGRA234_CLK_PLLP_OUT0>;
+			assigned-clocks = <&bpmp TEGRA234_CLK_I2C1>;
+			assigned-clock-parents = <&bpmp TEGRA234_CLK_PLLP_OUT0>;
+			clock-names = "div-clk", "parent";
+			resets = <&bpmp TEGRA234_RESET_I2C1>;
+			reset-names = "i2c";
+			iommus = <&smmu_niso0 TEGRA234_SID_GPCDMA>;
+			dma-coherent;
+			dmas = <&gpcdma 21>, <&gpcdma 21>;
+			dma-names = "rx", "tx";
+		};
+
+		cam_i2c: i2c@3180000 {
+			compatible = "nvidia,tegra194-i2c";
+			reg = <0x3180000 0x100>;
+			interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+			clock-frequency = <400000>;
+			clocks = <&bpmp TEGRA234_CLK_I2C3
+				&bpmp TEGRA234_CLK_PLLP_OUT0>;
+			assigned-clocks = <&bpmp TEGRA234_CLK_I2C3>;
+			assigned-clock-parents = <&bpmp TEGRA234_CLK_PLLP_OUT0>;
+			clock-names = "div-clk", "parent";
+			resets = <&bpmp TEGRA234_RESET_I2C3>;
+			reset-names = "i2c";
+			iommus = <&smmu_niso0 TEGRA234_SID_GPCDMA>;
+			dma-coherent;
+			dmas = <&gpcdma 23>, <&gpcdma 23>;
+			dma-names = "rx", "tx";
+		};
+
+		dp_aux_ch1_i2c: i2c@3190000 {
+			compatible = "nvidia,tegra194-i2c";
+			reg = <0x3190000 0x100>;
+			interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+			clock-frequency = <100000>;
+			clocks = <&bpmp TEGRA234_CLK_I2C4
+				&bpmp TEGRA234_CLK_PLLP_OUT0>;
+			assigned-clocks = <&bpmp TEGRA234_CLK_I2C4>;
+			assigned-clock-parents = <&bpmp TEGRA234_CLK_PLLP_OUT0>;
+			clock-names = "div-clk", "parent";
+			resets = <&bpmp TEGRA234_RESET_I2C4>;
+			reset-names = "i2c";
+			iommus = <&smmu_niso0 TEGRA234_SID_GPCDMA>;
+			dma-coherent;
+			dmas = <&gpcdma 26>, <&gpcdma 26>;
+			dma-names = "rx", "tx";
+		};
+
+		dp_aux_ch0_i2c: i2c@31b0000 {
+			compatible = "nvidia,tegra194-i2c";
+			reg = <0x31b0000 0x100>;
+			interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+			clock-frequency = <100000>;
+			clocks = <&bpmp TEGRA234_CLK_I2C6
+				&bpmp TEGRA234_CLK_PLLP_OUT0>;
+			assigned-clocks = <&bpmp TEGRA234_CLK_I2C6>;
+			assigned-clock-parents = <&bpmp TEGRA234_CLK_PLLP_OUT0>;
+			clock-names = "div-clk", "parent";
+			resets = <&bpmp TEGRA234_RESET_I2C6>;
+			reset-names = "i2c";
+			iommus = <&smmu_niso0 TEGRA234_SID_GPCDMA>;
+			dma-coherent;
+			dmas = <&gpcdma 30>, <&gpcdma 30>;
+			dma-names = "rx", "tx";
+		};
+
+		dp_aux_ch2_i2c: i2c@31c0000 {
+			compatible = "nvidia,tegra194-i2c";
+			reg = <0x31c0000 0x100>;
+			interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+			clock-frequency = <100000>;
+			clocks = <&bpmp TEGRA234_CLK_I2C7
+				&bpmp TEGRA234_CLK_PLLP_OUT0>;
+			assigned-clocks = <&bpmp TEGRA234_CLK_I2C7>;
+			assigned-clock-parents = <&bpmp TEGRA234_CLK_PLLP_OUT0>;
+			clock-names = "div-clk", "parent";
+			resets = <&bpmp TEGRA234_RESET_I2C7>;
+			reset-names = "i2c";
+			iommus = <&smmu_niso0 TEGRA234_SID_GPCDMA>;
+			dma-coherent;
+			dmas = <&gpcdma 27>, <&gpcdma 27>;
+			dma-names = "rx", "tx";
+		};
+
+		dp_aux_ch3_i2c: i2c@31e0000 {
+			compatible = "nvidia,tegra194-i2c";
+			reg = <0x31e0000 0x100>;
+			interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+			clock-frequency = <100000>;
+			clocks = <&bpmp TEGRA234_CLK_I2C9
+				&bpmp TEGRA234_CLK_PLLP_OUT0>;
+			assigned-clocks = <&bpmp TEGRA234_CLK_I2C9>;
+			assigned-clock-parents = <&bpmp TEGRA234_CLK_PLLP_OUT0>;
+			clock-names = "div-clk", "parent";
+			resets = <&bpmp TEGRA234_RESET_I2C9>;
+			reset-names = "i2c";
+			iommus = <&smmu_niso0 TEGRA234_SID_GPCDMA>;
+			dma-coherent;
+			dmas = <&gpcdma 31>, <&gpcdma 31>;
+			dma-names = "rx", "tx";
+		};
+
+		spi@3270000 {
+			compatible = "nvidia,tegra234-qspi";
+			reg = <0x3270000 0x1000>;
+			interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			clocks = <&bpmp TEGRA234_CLK_QSPI0_2X_PM>,
+				 <&bpmp TEGRA234_CLK_QSPI0_PM>;
+			clock-names = "qspi", "qspi_out";
+			resets = <&bpmp TEGRA234_RESET_QSPI0>;
+			reset-names = "qspi";
+			status = "disabled";
+		};
+
+		pwm1: pwm@3280000 {
+			compatible = "nvidia,tegra194-pwm",
+				     "nvidia,tegra186-pwm";
+			reg = <0x3280000 0x10000>;
+			clocks = <&bpmp TEGRA234_CLK_PWM1>;
+			clock-names = "pwm";
+			resets = <&bpmp TEGRA234_RESET_PWM1>;
+			reset-names = "pwm";
+			status = "disabled";
+			#pwm-cells = <2>;
+		};
+
+		spi@3300000 {
+			compatible = "nvidia,tegra234-qspi";
+			reg = <0x3300000 0x1000>;
+			interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			clocks = <&bpmp TEGRA234_CLK_QSPI1_2X_PM>,
+				 <&bpmp TEGRA234_CLK_QSPI1_PM>;
+			clock-names = "qspi", "qspi_out";
+			resets = <&bpmp TEGRA234_RESET_QSPI1>;
+			reset-names = "qspi";
+			status = "disabled";
+		};
+
 		mmc@3460000 {
 			compatible = "nvidia,tegra234-sdhci", "nvidia,tegra186-sdhci";
 			reg = <0x03460000 0x20000>;
 			interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&bpmp TEGRA234_CLK_SDMMC4>;
-			clock-names = "sdhci";
+			clocks = <&bpmp TEGRA234_CLK_SDMMC4>,
+				 <&bpmp TEGRA234_CLK_SDMMC_LEGACY_TM>;
+			clock-names = "sdhci", "tmclk";
+			assigned-clocks = <&bpmp TEGRA234_CLK_SDMMC4>,
+					  <&bpmp TEGRA234_CLK_PLLC4>;
+			assigned-clock-parents = <&bpmp TEGRA234_CLK_PLLC4>;
 			resets = <&bpmp TEGRA234_RESET_SDMMC4>;
 			reset-names = "sdhci";
-			dma-coherent;
+			interconnects = <&mc TEGRA234_MEMORY_CLIENT_SDMMCRAB &emc>,
+					<&mc TEGRA234_MEMORY_CLIENT_SDMMCWAB &emc>;
+			interconnect-names = "dma-mem", "write";
+			iommus = <&smmu_niso1 TEGRA234_SID_SDMMC4>;
+			nvidia,pad-autocal-pull-up-offset-hs400 = <0x00>;
+			nvidia,pad-autocal-pull-down-offset-hs400 = <0x00>;
+			nvidia,pad-autocal-pull-up-offset-1v8-timeout = <0x0a>;
+			nvidia,pad-autocal-pull-down-offset-1v8-timeout = <0x0a>;
+			nvidia,pad-autocal-pull-up-offset-3v3-timeout = <0x0a>;
+			nvidia,pad-autocal-pull-down-offset-3v3-timeout = <0x0a>;
+			nvidia,default-tap = <0x8>;
+			nvidia,default-trim = <0x14>;
+			nvidia,dqs-trim = <40>;
+			supports-cqe;
+			status = "disabled";
+		};
+
+		hda@3510000 {
+			compatible = "nvidia,tegra234-hda", "nvidia,tegra30-hda";
+			reg = <0x3510000 0x10000>;
+			interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&bpmp TEGRA234_CLK_AZA_BIT>,
+				 <&bpmp TEGRA234_CLK_AZA_2XBIT>;
+			clock-names = "hda", "hda2codec_2x";
+			resets = <&bpmp TEGRA234_RESET_HDA>,
+				 <&bpmp TEGRA234_RESET_HDACODEC>;
+			reset-names = "hda", "hda2codec_2x";
+			power-domains = <&bpmp TEGRA234_POWER_DOMAIN_DISP>;
+			interconnects = <&mc TEGRA234_MEMORY_CLIENT_HDAR &emc>,
+					<&mc TEGRA234_MEMORY_CLIENT_HDAW &emc>;
+			interconnect-names = "dma-mem", "write";
+			iommus = <&smmu_niso0 TEGRA234_SID_HDA>;
 			status = "disabled";
 		};
 
@@ -73,6 +967,490 @@
 			#mbox-cells = <2>;
 		};
 
+		ethernet@6800000 {
+			compatible = "nvidia,tegra234-mgbe";
+			reg = <0x06800000 0x10000>,
+			      <0x06810000 0x10000>,
+			      <0x068a0000 0x10000>;
+			reg-names = "hypervisor", "mac", "xpcs";
+			interrupts = <GIC_SPI 384 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "common";
+			clocks = <&bpmp TEGRA234_CLK_MGBE0_APP>,
+				 <&bpmp TEGRA234_CLK_MGBE0_MAC>,
+				 <&bpmp TEGRA234_CLK_MGBE0_MAC_DIVIDER>,
+				 <&bpmp TEGRA234_CLK_MGBE0_PTP_REF>,
+				 <&bpmp TEGRA234_CLK_MGBE0_RX_INPUT_M>,
+				 <&bpmp TEGRA234_CLK_MGBE0_RX_INPUT>,
+				 <&bpmp TEGRA234_CLK_MGBE0_TX>,
+				 <&bpmp TEGRA234_CLK_MGBE0_EEE_PCS>,
+				 <&bpmp TEGRA234_CLK_MGBE0_RX_PCS_INPUT>,
+				 <&bpmp TEGRA234_CLK_MGBE0_RX_PCS_M>,
+				 <&bpmp TEGRA234_CLK_MGBE0_RX_PCS>,
+				 <&bpmp TEGRA234_CLK_MGBE0_TX_PCS>;
+			clock-names = "mgbe", "mac", "mac-divider", "ptp-ref", "rx-input-m",
+				      "rx-input", "tx", "eee-pcs", "rx-pcs-input", "rx-pcs-m",
+				      "rx-pcs", "tx-pcs";
+			resets = <&bpmp TEGRA234_RESET_MGBE0_MAC>,
+				 <&bpmp TEGRA234_RESET_MGBE0_PCS>;
+			reset-names = "mac", "pcs";
+			interconnects = <&mc TEGRA234_MEMORY_CLIENT_MGBEARD &emc>,
+					<&mc TEGRA234_MEMORY_CLIENT_MGBEAWR &emc>;
+			interconnect-names = "dma-mem", "write";
+			iommus = <&smmu_niso0 TEGRA234_SID_MGBE>;
+			power-domains = <&bpmp TEGRA234_POWER_DOMAIN_MGBEA>;
+			status = "disabled";
+		};
+
+		ethernet@6900000 {
+			compatible = "nvidia,tegra234-mgbe";
+			reg = <0x06900000 0x10000>,
+			      <0x06910000 0x10000>,
+			      <0x069a0000 0x10000>;
+			reg-names = "hypervisor", "mac", "xpcs";
+			interrupts = <GIC_SPI 392 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "common";
+			clocks = <&bpmp TEGRA234_CLK_MGBE1_APP>,
+				 <&bpmp TEGRA234_CLK_MGBE1_MAC>,
+				 <&bpmp TEGRA234_CLK_MGBE1_MAC_DIVIDER>,
+				 <&bpmp TEGRA234_CLK_MGBE1_PTP_REF>,
+				 <&bpmp TEGRA234_CLK_MGBE1_RX_INPUT_M>,
+				 <&bpmp TEGRA234_CLK_MGBE1_RX_INPUT>,
+				 <&bpmp TEGRA234_CLK_MGBE1_TX>,
+				 <&bpmp TEGRA234_CLK_MGBE1_EEE_PCS>,
+				 <&bpmp TEGRA234_CLK_MGBE1_RX_PCS_INPUT>,
+				 <&bpmp TEGRA234_CLK_MGBE1_RX_PCS_M>,
+				 <&bpmp TEGRA234_CLK_MGBE1_RX_PCS>,
+				 <&bpmp TEGRA234_CLK_MGBE1_TX_PCS>;
+			clock-names = "mgbe", "mac", "mac-divider", "ptp-ref", "rx-input-m",
+				      "rx-input", "tx", "eee-pcs", "rx-pcs-input", "rx-pcs-m",
+				      "rx-pcs", "tx-pcs";
+			resets = <&bpmp TEGRA234_RESET_MGBE1_MAC>,
+				 <&bpmp TEGRA234_RESET_MGBE1_PCS>;
+			reset-names = "mac", "pcs";
+			interconnects = <&mc TEGRA234_MEMORY_CLIENT_MGBEBRD &emc>,
+					<&mc TEGRA234_MEMORY_CLIENT_MGBEBWR &emc>;
+			interconnect-names = "dma-mem", "write";
+			iommus = <&smmu_niso0 TEGRA234_SID_MGBE_VF1>;
+			power-domains = <&bpmp TEGRA234_POWER_DOMAIN_MGBEB>;
+			status = "disabled";
+		};
+
+		ethernet@6a00000 {
+			compatible = "nvidia,tegra234-mgbe";
+			reg = <0x06a00000 0x10000>,
+			      <0x06a10000 0x10000>,
+			      <0x06aa0000 0x10000>;
+			reg-names = "hypervisor", "mac", "xpcs";
+			interrupts = <GIC_SPI 400 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "common";
+			clocks = <&bpmp TEGRA234_CLK_MGBE2_APP>,
+				 <&bpmp TEGRA234_CLK_MGBE2_MAC>,
+				 <&bpmp TEGRA234_CLK_MGBE2_MAC_DIVIDER>,
+				 <&bpmp TEGRA234_CLK_MGBE2_PTP_REF>,
+				 <&bpmp TEGRA234_CLK_MGBE2_RX_INPUT_M>,
+				 <&bpmp TEGRA234_CLK_MGBE2_RX_INPUT>,
+				 <&bpmp TEGRA234_CLK_MGBE2_TX>,
+				 <&bpmp TEGRA234_CLK_MGBE2_EEE_PCS>,
+				 <&bpmp TEGRA234_CLK_MGBE2_RX_PCS_INPUT>,
+				 <&bpmp TEGRA234_CLK_MGBE2_RX_PCS_M>,
+				 <&bpmp TEGRA234_CLK_MGBE2_RX_PCS>,
+				 <&bpmp TEGRA234_CLK_MGBE2_TX_PCS>;
+			clock-names = "mgbe", "mac", "mac-divider", "ptp-ref", "rx-input-m",
+				      "rx-input", "tx", "eee-pcs", "rx-pcs-input", "rx-pcs-m",
+				      "rx-pcs", "tx-pcs";
+			resets = <&bpmp TEGRA234_RESET_MGBE2_MAC>,
+				 <&bpmp TEGRA234_RESET_MGBE2_PCS>;
+			reset-names = "mac", "pcs";
+			interconnects = <&mc TEGRA234_MEMORY_CLIENT_MGBECRD &emc>,
+					<&mc TEGRA234_MEMORY_CLIENT_MGBECWR &emc>;
+			interconnect-names = "dma-mem", "write";
+			iommus = <&smmu_niso0 TEGRA234_SID_MGBE_VF2>;
+			power-domains = <&bpmp TEGRA234_POWER_DOMAIN_MGBEC>;
+			status = "disabled";
+		};
+
+		ethernet@6b00000 {
+			compatible = "nvidia,tegra234-mgbe";
+			reg = <0x06b00000 0x10000>,
+			      <0x06b10000 0x10000>,
+			      <0x06ba0000 0x10000>;
+			reg-names = "hypervisor", "mac", "xpcs";
+			interrupts = <GIC_SPI 408 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "common";
+			clocks = <&bpmp TEGRA234_CLK_MGBE3_APP>,
+				 <&bpmp TEGRA234_CLK_MGBE3_MAC>,
+				 <&bpmp TEGRA234_CLK_MGBE3_MAC_DIVIDER>,
+				 <&bpmp TEGRA234_CLK_MGBE3_PTP_REF>,
+				 <&bpmp TEGRA234_CLK_MGBE3_RX_INPUT_M>,
+				 <&bpmp TEGRA234_CLK_MGBE3_RX_INPUT>,
+				 <&bpmp TEGRA234_CLK_MGBE3_TX>,
+				 <&bpmp TEGRA234_CLK_MGBE3_EEE_PCS>,
+				 <&bpmp TEGRA234_CLK_MGBE3_RX_PCS_INPUT>,
+				 <&bpmp TEGRA234_CLK_MGBE3_RX_PCS_M>,
+				 <&bpmp TEGRA234_CLK_MGBE3_RX_PCS>,
+				 <&bpmp TEGRA234_CLK_MGBE3_TX_PCS>;
+			clock-names = "mgbe", "mac", "mac-divider", "ptp-ref", "rx-input-m",
+				      "rx-input", "tx", "eee-pcs", "rx-pcs-input", "rx-pcs-m",
+				      "rx-pcs", "tx-pcs";
+			resets = <&bpmp TEGRA234_RESET_MGBE3_MAC>,
+				 <&bpmp TEGRA234_RESET_MGBE3_PCS>;
+			reset-names = "mac", "pcs";
+			interconnects = <&mc TEGRA234_MEMORY_CLIENT_MGBEDRD &emc>,
+					<&mc TEGRA234_MEMORY_CLIENT_MGBEDWR &emc>;
+			interconnect-names = "dma-mem", "write";
+			iommus = <&smmu_niso0 TEGRA234_SID_MGBE_VF3>;
+			power-domains = <&bpmp TEGRA234_POWER_DOMAIN_MGBED>;
+			status = "disabled";
+		};
+
+		smmu_niso1: iommu@8000000 {
+			compatible = "nvidia,tegra234-smmu", "nvidia,smmu-500";
+			reg = <0x8000000 0x1000000>,
+			      <0x7000000 0x1000000>;
+			interrupts = <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 242 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 242 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>;
+			stream-match-mask = <0x7f80>;
+			#global-interrupts = <2>;
+			#iommu-cells = <1>;
+
+			nvidia,memory-controller = <&mc>;
+			status = "okay";
+		};
+
+		sce-fabric@b600000 {
+			compatible = "nvidia,tegra234-sce-fabric";
+			reg = <0xb600000 0x40000>;
+			interrupts = <GIC_SPI 173 IRQ_TYPE_LEVEL_HIGH>;
+			status = "okay";
+		};
+
+		rce-fabric@be00000 {
+			compatible = "nvidia,tegra234-rce-fabric";
+			reg = <0xbe00000 0x40000>;
+			interrupts = <GIC_SPI 175 IRQ_TYPE_LEVEL_HIGH>;
+			status = "okay";
+		};
+
+		p2u_hsio_0: phy@3e00000 {
+			compatible = "nvidia,tegra234-p2u";
+			reg = <0x03e00000 0x10000>;
+			reg-names = "ctl";
+
+			#phy-cells = <0>;
+		};
+
+		p2u_hsio_1: phy@3e10000 {
+			compatible = "nvidia,tegra234-p2u";
+			reg = <0x03e10000 0x10000>;
+			reg-names = "ctl";
+
+			#phy-cells = <0>;
+		};
+
+		p2u_hsio_2: phy@3e20000 {
+			compatible = "nvidia,tegra234-p2u";
+			reg = <0x03e20000 0x10000>;
+			reg-names = "ctl";
+
+			#phy-cells = <0>;
+		};
+
+		p2u_hsio_3: phy@3e30000 {
+			compatible = "nvidia,tegra234-p2u";
+			reg = <0x03e30000 0x10000>;
+			reg-names = "ctl";
+
+			#phy-cells = <0>;
+		};
+
+		p2u_hsio_4: phy@3e40000 {
+			compatible = "nvidia,tegra234-p2u";
+			reg = <0x03e40000 0x10000>;
+			reg-names = "ctl";
+
+			#phy-cells = <0>;
+		};
+
+		p2u_hsio_5: phy@3e50000 {
+			compatible = "nvidia,tegra234-p2u";
+			reg = <0x03e50000 0x10000>;
+			reg-names = "ctl";
+
+			#phy-cells = <0>;
+		};
+
+		p2u_hsio_6: phy@3e60000 {
+			compatible = "nvidia,tegra234-p2u";
+			reg = <0x03e60000 0x10000>;
+			reg-names = "ctl";
+
+			#phy-cells = <0>;
+		};
+
+		p2u_hsio_7: phy@3e70000 {
+			compatible = "nvidia,tegra234-p2u";
+			reg = <0x03e70000 0x10000>;
+			reg-names = "ctl";
+
+			#phy-cells = <0>;
+		};
+
+		p2u_nvhs_0: phy@3e90000 {
+			compatible = "nvidia,tegra234-p2u";
+			reg = <0x03e90000 0x10000>;
+			reg-names = "ctl";
+
+			#phy-cells = <0>;
+		};
+
+		p2u_nvhs_1: phy@3ea0000 {
+			compatible = "nvidia,tegra234-p2u";
+			reg = <0x03ea0000 0x10000>;
+			reg-names = "ctl";
+
+			#phy-cells = <0>;
+		};
+
+		p2u_nvhs_2: phy@3eb0000 {
+			compatible = "nvidia,tegra234-p2u";
+			reg = <0x03eb0000 0x10000>;
+			reg-names = "ctl";
+
+			#phy-cells = <0>;
+		};
+
+		p2u_nvhs_3: phy@3ec0000 {
+			compatible = "nvidia,tegra234-p2u";
+			reg = <0x03ec0000 0x10000>;
+			reg-names = "ctl";
+
+			#phy-cells = <0>;
+		};
+
+		p2u_nvhs_4: phy@3ed0000 {
+			compatible = "nvidia,tegra234-p2u";
+			reg = <0x03ed0000 0x10000>;
+			reg-names = "ctl";
+
+			#phy-cells = <0>;
+		};
+
+		p2u_nvhs_5: phy@3ee0000 {
+			compatible = "nvidia,tegra234-p2u";
+			reg = <0x03ee0000 0x10000>;
+			reg-names = "ctl";
+
+			#phy-cells = <0>;
+		};
+
+		p2u_nvhs_6: phy@3ef0000 {
+			compatible = "nvidia,tegra234-p2u";
+			reg = <0x03ef0000 0x10000>;
+			reg-names = "ctl";
+
+			#phy-cells = <0>;
+		};
+
+		p2u_nvhs_7: phy@3f00000 {
+			compatible = "nvidia,tegra234-p2u";
+			reg = <0x03f00000 0x10000>;
+			reg-names = "ctl";
+
+			#phy-cells = <0>;
+		};
+
+		p2u_gbe_0: phy@3f20000 {
+			compatible = "nvidia,tegra234-p2u";
+			reg = <0x03f20000 0x10000>;
+			reg-names = "ctl";
+
+			#phy-cells = <0>;
+		};
+
+		p2u_gbe_1: phy@3f30000 {
+			compatible = "nvidia,tegra234-p2u";
+			reg = <0x03f30000 0x10000>;
+			reg-names = "ctl";
+
+			#phy-cells = <0>;
+		};
+
+		p2u_gbe_2: phy@3f40000 {
+			compatible = "nvidia,tegra234-p2u";
+			reg = <0x03f40000 0x10000>;
+			reg-names = "ctl";
+
+			#phy-cells = <0>;
+		};
+
+		p2u_gbe_3: phy@3f50000 {
+			compatible = "nvidia,tegra234-p2u";
+			reg = <0x03f50000 0x10000>;
+			reg-names = "ctl";
+
+			#phy-cells = <0>;
+		};
+
+		p2u_gbe_4: phy@3f60000 {
+			compatible = "nvidia,tegra234-p2u";
+			reg = <0x03f60000 0x10000>;
+			reg-names = "ctl";
+
+			#phy-cells = <0>;
+		};
+
+		p2u_gbe_5: phy@3f70000 {
+			compatible = "nvidia,tegra234-p2u";
+			reg = <0x03f70000 0x10000>;
+			reg-names = "ctl";
+
+			#phy-cells = <0>;
+		};
+
+		p2u_gbe_6: phy@3f80000 {
+			compatible = "nvidia,tegra234-p2u";
+			reg = <0x03f80000 0x10000>;
+			reg-names = "ctl";
+
+			#phy-cells = <0>;
+		};
+
+		p2u_gbe_7: phy@3f90000 {
+			compatible = "nvidia,tegra234-p2u";
+			reg = <0x03f90000 0x10000>;
+			reg-names = "ctl";
+
+			#phy-cells = <0>;
+		};
+
 		hsp_aon: hsp@c150000 {
 			compatible = "nvidia,tegra234-hsp", "nvidia,tegra194-hsp";
 			reg = <0x0c150000 0x90000>;
@@ -88,14 +1466,70 @@
 			#mbox-cells = <2>;
 		};
 
+		gen2_i2c: i2c@c240000 {
+			compatible = "nvidia,tegra194-i2c";
+			reg = <0xc240000 0x100>;
+			interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+			clock-frequency = <100000>;
+			clocks = <&bpmp TEGRA234_CLK_I2C2
+				&bpmp TEGRA234_CLK_PLLP_OUT0>;
+			clock-names = "div-clk", "parent";
+			assigned-clocks = <&bpmp TEGRA234_CLK_I2C2>;
+			assigned-clock-parents = <&bpmp TEGRA234_CLK_PLLP_OUT0>;
+			resets = <&bpmp TEGRA234_RESET_I2C2>;
+			reset-names = "i2c";
+			iommus = <&smmu_niso0 TEGRA234_SID_GPCDMA>;
+			dma-coherent;
+			dmas = <&gpcdma 22>, <&gpcdma 22>;
+			dma-names = "rx", "tx";
+		};
+
+		gen8_i2c: i2c@c250000 {
+			compatible = "nvidia,tegra194-i2c";
+			reg = <0xc250000 0x100>;
+			nvidia,hw-instance-id = <0x7>;
+			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+			clock-frequency = <400000>;
+			clocks = <&bpmp TEGRA234_CLK_I2C8
+				&bpmp TEGRA234_CLK_PLLP_OUT0>;
+			clock-names = "div-clk", "parent";
+			assigned-clocks = <&bpmp TEGRA234_CLK_I2C8>;
+			assigned-clock-parents = <&bpmp TEGRA234_CLK_PLLP_OUT0>;
+			resets = <&bpmp TEGRA234_RESET_I2C8>;
+			reset-names = "i2c";
+			iommus = <&smmu_niso0 TEGRA234_SID_GPCDMA>;
+			dma-coherent;
+			dmas = <&gpcdma 0>, <&gpcdma 0>;
+			dma-names = "rx", "tx";
+		};
+
 		rtc@c2a0000 {
 			compatible = "nvidia,tegra234-rtc", "nvidia,tegra20-rtc";
 			reg = <0x0c2a0000 0x10000>;
 			interrupt-parent = <&pmc>;
 			interrupts = <73 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&bpmp TEGRA234_CLK_CLK_32K>;
+			clock-names = "rtc";
 			status = "disabled";
 		};
 
+		gpio_aon: gpio@c2f0000 {
+			compatible = "nvidia,tegra234-gpio-aon";
+			reg-names = "security", "gpio";
+			reg = <0x0c2f0000 0x1000>,
+			      <0x0c2f1000 0x1000>;
+			interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>;
+			#interrupt-cells = <2>;
+			interrupt-controller;
+			#gpio-cells = <2>;
+			gpio-controller;
+		};
+
 		pmc: pmc@c360000 {
 			compatible = "nvidia,tegra234-pmc";
 			reg = <0x0c360000 0x10000>,
@@ -109,6 +1543,27 @@
 			interrupt-controller;
 		};
 
+		aon-fabric@c600000 {
+			compatible = "nvidia,tegra234-aon-fabric";
+			reg = <0xc600000 0x40000>;
+			interrupts = <GIC_SPI 172 IRQ_TYPE_LEVEL_HIGH>;
+			status = "okay";
+		};
+
+		bpmp-fabric@d600000 {
+			compatible = "nvidia,tegra234-bpmp-fabric";
+			reg = <0xd600000 0x40000>;
+			interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>;
+			status = "okay";
+		};
+
+		dce-fabric@de00000 {
+			compatible = "nvidia,tegra234-sce-fabric";
+			reg = <0xde00000 0x40000>;
+			interrupts = <GIC_SPI 381 IRQ_TYPE_LEVEL_HIGH>;
+			status = "okay";
+		};
+
 		gic: interrupt-controller@f400000 {
 			compatible = "arm,gic-v3";
 			reg = <0x0f400000 0x010000>, /* GICD */
@@ -120,23 +1575,1055 @@
 			#interrupt-cells = <3>;
 			interrupt-controller;
 		};
+
+		smmu_iso: iommu@10000000{
+			compatible = "nvidia,tegra234-smmu", "nvidia,smmu-500";
+			reg = <0x10000000 0x1000000>;
+			interrupts = <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>;
+			stream-match-mask = <0x7f80>;
+			#global-interrupts = <1>;
+			#iommu-cells = <1>;
+
+			nvidia,memory-controller = <&mc>;
+			status = "okay";
+		};
+
+		smmu_niso0: iommu@12000000 {
+			compatible = "nvidia,tegra234-smmu", "nvidia,smmu-500";
+			reg = <0x12000000 0x1000000>,
+			      <0x11000000 0x1000000>;
+			interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 232 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 232 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>;
+			stream-match-mask = <0x7f80>;
+			#global-interrupts = <2>;
+			#iommu-cells = <1>;
+
+			nvidia,memory-controller = <&mc>;
+			status = "okay";
+		};
+
+		cbb-fabric@13a00000 {
+			compatible = "nvidia,tegra234-cbb-fabric";
+			reg = <0x13a00000 0x400000>;
+			interrupts = <GIC_SPI 231 IRQ_TYPE_LEVEL_HIGH>;
+			status = "okay";
+		};
+	};
+
+	ccplex@e000000 {
+		compatible = "nvidia,tegra234-ccplex-cluster";
+		reg = <0x0 0x0e000000 0x0 0x5ffff>;
+		nvidia,bpmp = <&bpmp>;
+		status = "okay";
+	};
+
+	pcie@140a0000 {
+		compatible = "nvidia,tegra234-pcie";
+		power-domains = <&bpmp TEGRA234_POWER_DOMAIN_PCIEX4CA>;
+		reg = <0x00 0x140a0000 0x0 0x00020000>, /* appl registers (128K)      */
+		      <0x00 0x2a000000 0x0 0x00040000>, /* configuration space (256K) */
+		      <0x00 0x2a040000 0x0 0x00040000>, /* iATU_DMA reg space (256K)  */
+		      <0x00 0x2a080000 0x0 0x00040000>; /* DBI reg space (256K)       */
+		reg-names = "appl", "config", "atu_dma", "dbi";
+
+		#address-cells = <3>;
+		#size-cells = <2>;
+		device_type = "pci";
+		num-lanes = <4>;
+		num-viewport = <8>;
+		linux,pci-domain = <8>;
+
+		clocks = <&bpmp TEGRA234_CLK_PEX2_C8_CORE>;
+		clock-names = "core";
+
+		resets = <&bpmp TEGRA234_RESET_PEX2_CORE_8_APB>,
+			 <&bpmp TEGRA234_RESET_PEX2_CORE_8>;
+		reset-names = "apb", "core";
+
+		interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>, /* controller interrupt */
+			     <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>; /* MSI interrupt */
+		interrupt-names = "intr", "msi";
+
+		#interrupt-cells = <1>;
+		interrupt-map-mask = <0 0 0 0>;
+		interrupt-map = <0 0 0 0 &gic GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
+
+		nvidia,bpmp = <&bpmp 8>;
+
+		nvidia,aspm-cmrt-us = <60>;
+		nvidia,aspm-pwr-on-t-us = <20>;
+		nvidia,aspm-l0s-entrance-latency-us = <3>;
+
+		bus-range = <0x0 0xff>;
+
+		ranges = <0x43000000 0x32 0x40000000 0x32 0x40000000 0x2 0xe8000000>, /* prefetchable memory (11904 MB) */
+			 <0x02000000 0x0  0x40000000 0x35 0x28000000 0x0 0x08000000>, /* non-prefetchable memory (128 MB) */
+			 <0x01000000 0x0  0x2a100000 0x00 0x2a100000 0x0 0x00100000>; /* downstream I/O (1 MB) */
+
+		interconnects = <&mc TEGRA234_MEMORY_CLIENT_PCIE8AR &emc>,
+				<&mc TEGRA234_MEMORY_CLIENT_PCIE8AW &emc>;
+		interconnect-names = "dma-mem", "write";
+		iommu-map = <0x0 &smmu_niso1 TEGRA234_SID_PCIE8 0x1000>;
+		iommu-map-mask = <0x0>;
+		dma-coherent;
+
+		status = "disabled";
+	};
+
+	pcie@140c0000 {
+		compatible = "nvidia,tegra234-pcie";
+		power-domains = <&bpmp TEGRA234_POWER_DOMAIN_PCIEX4CB>;
+		reg = <0x00 0x140c0000 0x0 0x00020000>, /* appl registers (128K)      */
+		      <0x00 0x2c000000 0x0 0x00040000>, /* configuration space (256K) */
+		      <0x00 0x2c040000 0x0 0x00040000>, /* iATU_DMA reg space (256K)  */
+		      <0x00 0x2c080000 0x0 0x00040000>; /* DBI reg space (256K)       */
+		reg-names = "appl", "config", "atu_dma", "dbi";
+
+		#address-cells = <3>;
+		#size-cells = <2>;
+		device_type = "pci";
+		num-lanes = <4>;
+		num-viewport = <8>;
+		linux,pci-domain = <9>;
+
+		clocks = <&bpmp TEGRA234_CLK_PEX2_C9_CORE>;
+		clock-names = "core";
+
+		resets = <&bpmp TEGRA234_RESET_PEX2_CORE_9_APB>,
+			 <&bpmp TEGRA234_RESET_PEX2_CORE_9>;
+		reset-names = "apb", "core";
+
+		interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>, /* controller interrupt */
+			     <GIC_SPI 359 IRQ_TYPE_LEVEL_HIGH>; /* MSI interrupt */
+		interrupt-names = "intr", "msi";
+
+		#interrupt-cells = <1>;
+		interrupt-map-mask = <0 0 0 0>;
+		interrupt-map = <0 0 0 0 &gic GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
+
+		nvidia,bpmp = <&bpmp 9>;
+
+		nvidia,aspm-cmrt-us = <60>;
+		nvidia,aspm-pwr-on-t-us = <20>;
+		nvidia,aspm-l0s-entrance-latency-us = <3>;
+
+		bus-range = <0x0 0xff>;
+
+		ranges = <0x43000000 0x35 0x40000000 0x35 0x40000000 0x2 0xe8000000>, /* prefetchable memory (11904 MB) */
+			 <0x02000000 0x0  0x40000000 0x38 0x28000000 0x0 0x08000000>, /* non-prefetchable memory (128 MB) */
+			 <0x01000000 0x0  0x2c100000 0x00 0x2c100000 0x0 0x00100000>; /* downstream I/O (1 MB) */
+
+		interconnects = <&mc TEGRA234_MEMORY_CLIENT_PCIE9AR &emc>,
+				<&mc TEGRA234_MEMORY_CLIENT_PCIE9AW &emc>;
+		interconnect-names = "dma-mem", "write";
+		iommu-map = <0x0 &smmu_niso0 TEGRA234_SID_PCIE9 0x1000>;
+		iommu-map-mask = <0x0>;
+		dma-coherent;
+
+		status = "disabled";
+	};
+
+	pcie@140e0000 {
+		compatible = "nvidia,tegra234-pcie";
+		power-domains = <&bpmp TEGRA234_POWER_DOMAIN_PCIEX4CC>;
+		reg = <0x00 0x140e0000 0x0 0x00020000>, /* appl registers (128K)      */
+		      <0x00 0x2e000000 0x0 0x00040000>, /* configuration space (256K) */
+		      <0x00 0x2e040000 0x0 0x00040000>, /* iATU_DMA reg space (256K)  */
+		      <0x00 0x2e080000 0x0 0x00040000>; /* DBI reg space (256K)       */
+		reg-names = "appl", "config", "atu_dma", "dbi";
+
+		#address-cells = <3>;
+		#size-cells = <2>;
+		device_type = "pci";
+		num-lanes = <4>;
+		num-viewport = <8>;
+		linux,pci-domain = <10>;
+
+		clocks = <&bpmp TEGRA234_CLK_PEX2_C10_CORE>;
+		clock-names = "core";
+
+		resets = <&bpmp TEGRA234_RESET_PEX2_CORE_10_APB>,
+			 <&bpmp TEGRA234_RESET_PEX2_CORE_10>;
+		reset-names = "apb", "core";
+
+		interrupts = <GIC_SPI 360 IRQ_TYPE_LEVEL_HIGH>, /* controller interrupt */
+			     <GIC_SPI 361 IRQ_TYPE_LEVEL_HIGH>; /* MSI interrupt */
+		interrupt-names = "intr", "msi";
+
+		#interrupt-cells = <1>;
+		interrupt-map-mask = <0 0 0 0>;
+		interrupt-map = <0 0 0 0 &gic GIC_SPI 360 IRQ_TYPE_LEVEL_HIGH>;
+
+		nvidia,bpmp = <&bpmp 10>;
+
+		nvidia,aspm-cmrt-us = <60>;
+		nvidia,aspm-pwr-on-t-us = <20>;
+		nvidia,aspm-l0s-entrance-latency-us = <3>;
+
+		bus-range = <0x0 0xff>;
+
+		ranges = <0x43000000 0x38 0x40000000 0x38 0x40000000 0x2 0xe8000000>, /* prefetchable memory (11904 MB) */
+			 <0x02000000 0x0  0x40000000 0x3b 0x28000000 0x0 0x08000000>, /* non-prefetchable memory (128 MB) */
+			 <0x01000000 0x0  0x2e100000 0x00 0x2e100000 0x0 0x00100000>; /* downstream I/O (1 MB) */
+
+		interconnects = <&mc TEGRA234_MEMORY_CLIENT_PCIE10AR &emc>,
+				<&mc TEGRA234_MEMORY_CLIENT_PCIE10AW &emc>;
+		interconnect-names = "dma-mem", "write";
+		iommu-map = <0x0 &smmu_niso1 TEGRA234_SID_PCIE10 0x1000>;
+		iommu-map-mask = <0x0>;
+		dma-coherent;
+
+		status = "disabled";
+	};
+
+	pcie@14100000 {
+		compatible = "nvidia,tegra234-pcie";
+		power-domains = <&bpmp TEGRA234_POWER_DOMAIN_PCIEX1A>;
+		reg = <0x00 0x14100000 0x0 0x00020000>, /* appl registers (128K)      */
+		      <0x00 0x30000000 0x0 0x00040000>, /* configuration space (256K) */
+		      <0x00 0x30040000 0x0 0x00040000>, /* iATU_DMA reg space (256K)  */
+		      <0x00 0x30080000 0x0 0x00040000>; /* DBI reg space (256K)       */
+		reg-names = "appl", "config", "atu_dma", "dbi";
+
+		#address-cells = <3>;
+		#size-cells = <2>;
+		device_type = "pci";
+		num-lanes = <1>;
+		num-viewport = <8>;
+		linux,pci-domain = <1>;
+
+		clocks = <&bpmp TEGRA234_CLK_PEX0_C1_CORE>;
+		clock-names = "core";
+
+		resets = <&bpmp TEGRA234_RESET_PEX0_CORE_1_APB>,
+			 <&bpmp TEGRA234_RESET_PEX0_CORE_1>;
+		reset-names = "apb", "core";
+
+		interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>, /* controller interrupt */
+			     <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>; /* MSI interrupt */
+		interrupt-names = "intr", "msi";
+
+		#interrupt-cells = <1>;
+		interrupt-map-mask = <0 0 0 0>;
+		interrupt-map = <0 0 0 0 &gic GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
+
+		nvidia,bpmp = <&bpmp 1>;
+
+		nvidia,aspm-cmrt-us = <60>;
+		nvidia,aspm-pwr-on-t-us = <20>;
+		nvidia,aspm-l0s-entrance-latency-us = <3>;
+
+		bus-range = <0x0 0xff>;
+
+		ranges = <0x43000000 0x20 0x80000000 0x20 0x80000000 0x0 0x28000000>, /* prefetchable memory (640 MB) */
+			 <0x02000000 0x0  0x40000000 0x20 0xa8000000 0x0 0x08000000>, /* non-prefetchable memory (128 MB) */
+			 <0x01000000 0x0  0x30100000 0x00 0x30100000 0x0 0x00100000>; /* downstream I/O (1 MB) */
+
+		interconnects = <&mc TEGRA234_MEMORY_CLIENT_PCIE1R &emc>,
+				<&mc TEGRA234_MEMORY_CLIENT_PCIE1W &emc>;
+		interconnect-names = "dma-mem", "write";
+		iommu-map = <0x0 &smmu_niso1 TEGRA234_SID_PCIE1 0x1000>;
+		iommu-map-mask = <0x0>;
+		dma-coherent;
+
+		status = "disabled";
+	};
+
+	pcie@14120000 {
+		compatible = "nvidia,tegra234-pcie";
+		power-domains = <&bpmp TEGRA234_POWER_DOMAIN_PCIEX1A>;
+		reg = <0x00 0x14120000 0x0 0x00020000>, /* appl registers (128K)      */
+		      <0x00 0x32000000 0x0 0x00040000>, /* configuration space (256K) */
+		      <0x00 0x32040000 0x0 0x00040000>, /* iATU_DMA reg space (256K)  */
+		      <0x00 0x32080000 0x0 0x00040000>; /* DBI reg space (256K)       */
+		reg-names = "appl", "config", "atu_dma", "dbi";
+
+		#address-cells = <3>;
+		#size-cells = <2>;
+		device_type = "pci";
+		num-lanes = <1>;
+		num-viewport = <8>;
+		linux,pci-domain = <2>;
+
+		clocks = <&bpmp TEGRA234_CLK_PEX0_C2_CORE>;
+		clock-names = "core";
+
+		resets = <&bpmp TEGRA234_RESET_PEX0_CORE_2_APB>,
+			 <&bpmp TEGRA234_RESET_PEX0_CORE_2>;
+		reset-names = "apb", "core";
+
+		interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>, /* controller interrupt */
+			     <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>; /* MSI interrupt */
+		interrupt-names = "intr", "msi";
+
+		#interrupt-cells = <1>;
+		interrupt-map-mask = <0 0 0 0>;
+		interrupt-map = <0 0 0 0 &gic GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>;
+
+		nvidia,bpmp = <&bpmp 2>;
+
+		nvidia,aspm-cmrt-us = <60>;
+		nvidia,aspm-pwr-on-t-us = <20>;
+		nvidia,aspm-l0s-entrance-latency-us = <3>;
+
+		bus-range = <0x0 0xff>;
+
+		ranges = <0x43000000 0x20 0xc0000000 0x20 0xc0000000 0x0 0x28000000>, /* prefetchable memory (640 MB) */
+			 <0x02000000 0x0  0x40000000 0x20 0xe8000000 0x0 0x08000000>, /* non-prefetchable memory (128 MB) */
+			 <0x01000000 0x0  0x32100000 0x00 0x32100000 0x0 0x00100000>; /* downstream I/O (1 MB) */
+
+		interconnects = <&mc TEGRA234_MEMORY_CLIENT_PCIE2AR &emc>,
+				<&mc TEGRA234_MEMORY_CLIENT_PCIE2AW &emc>;
+		interconnect-names = "dma-mem", "write";
+		iommu-map = <0x0 &smmu_niso1 TEGRA234_SID_PCIE2 0x1000>;
+		iommu-map-mask = <0x0>;
+		dma-coherent;
+
+		status = "disabled";
+	};
+
+	pcie@14140000 {
+		compatible = "nvidia,tegra234-pcie";
+		power-domains = <&bpmp TEGRA234_POWER_DOMAIN_PCIEX1A>;
+		reg = <0x00 0x14140000 0x0 0x00020000>, /* appl registers (128K)      */
+		      <0x00 0x34000000 0x0 0x00040000>, /* configuration space (256K) */
+		      <0x00 0x34040000 0x0 0x00040000>, /* iATU_DMA reg space (256K)  */
+		      <0x00 0x34080000 0x0 0x00040000>; /* DBI reg space (256K)       */
+		reg-names = "appl", "config", "atu_dma", "dbi";
+
+		#address-cells = <3>;
+		#size-cells = <2>;
+		device_type = "pci";
+		num-lanes = <1>;
+		num-viewport = <8>;
+		linux,pci-domain = <3>;
+
+		clocks = <&bpmp TEGRA234_CLK_PEX0_C3_CORE>;
+		clock-names = "core";
+
+		resets = <&bpmp TEGRA234_RESET_PEX0_CORE_3_APB>,
+			 <&bpmp TEGRA234_RESET_PEX0_CORE_3>;
+		reset-names = "apb", "core";
+
+		interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>, /* controller interrupt */
+			     <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>; /* MSI interrupt */
+		interrupt-names = "intr", "msi";
+
+		#interrupt-cells = <1>;
+		interrupt-map-mask = <0 0 0 0>;
+		interrupt-map = <0 0 0 0 &gic GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
+
+		nvidia,bpmp = <&bpmp 3>;
+
+		nvidia,aspm-cmrt-us = <60>;
+		nvidia,aspm-pwr-on-t-us = <20>;
+		nvidia,aspm-l0s-entrance-latency-us = <3>;
+
+		bus-range = <0x0 0xff>;
+
+		ranges = <0x43000000 0x21 0x00000000 0x21 0x00000000 0x0 0x28000000>, /* prefetchable memory (640 MB) */
+			 <0x02000000 0x0  0x40000000 0x21 0xe8000000 0x0 0x08000000>, /* non-prefetchable memory (128 MB) */
+			 <0x01000000 0x0  0x34100000 0x00 0x34100000 0x0 0x00100000>; /* downstream I/O (1 MB) */
+
+		interconnects = <&mc TEGRA234_MEMORY_CLIENT_PCIE3R &emc>,
+				<&mc TEGRA234_MEMORY_CLIENT_PCIE3W &emc>;
+		interconnect-names = "dma-mem", "write";
+		iommu-map = <0x0 &smmu_niso1 TEGRA234_SID_PCIE3 0x1000>;
+		iommu-map-mask = <0x0>;
+		dma-coherent;
+
+		status = "disabled";
+	};
+
+	pcie@14160000 {
+		compatible = "nvidia,tegra234-pcie";
+		power-domains = <&bpmp TEGRA234_POWER_DOMAIN_PCIEX4BB>;
+		reg = <0x00 0x14160000 0x0 0x00020000>, /* appl registers (128K)      */
+		      <0x00 0x36000000 0x0 0x00040000>, /* configuration space (256K) */
+		      <0x00 0x36040000 0x0 0x00040000>, /* iATU_DMA reg space (256K)  */
+		      <0x00 0x36080000 0x0 0x00040000>; /* DBI reg space (256K)       */
+		reg-names = "appl", "config", "atu_dma", "dbi";
+
+		#address-cells = <3>;
+		#size-cells = <2>;
+		device_type = "pci";
+		num-lanes = <4>;
+		num-viewport = <8>;
+		linux,pci-domain = <4>;
+
+		clocks = <&bpmp TEGRA234_CLK_PEX0_C4_CORE>;
+		clock-names = "core";
+
+		resets = <&bpmp TEGRA234_RESET_PEX0_CORE_4_APB>,
+			 <&bpmp TEGRA234_RESET_PEX0_CORE_4>;
+		reset-names = "apb", "core";
+
+		interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>, /* controller interrupt */
+			     <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>; /* MSI interrupt */
+		interrupt-names = "intr", "msi";
+
+		#interrupt-cells = <1>;
+		interrupt-map-mask = <0 0 0 0>;
+		interrupt-map = <0 0 0 0 &gic GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
+
+		nvidia,bpmp = <&bpmp 4>;
+
+		nvidia,aspm-cmrt-us = <60>;
+		nvidia,aspm-pwr-on-t-us = <20>;
+		nvidia,aspm-l0s-entrance-latency-us = <3>;
+
+		bus-range = <0x0 0xff>;
+
+		ranges = <0x43000000 0x21 0x40000000 0x21 0x40000000 0x2 0xe8000000>, /* prefetchable memory (11904 MB) */
+			 <0x02000000 0x0  0x40000000 0x24 0x28000000 0x0 0x08000000>, /* non-prefetchable memory (128 MB) */
+			 <0x01000000 0x0  0x36100000 0x00 0x36100000 0x0 0x00100000>; /* downstream I/O (1 MB) */
+
+		interconnects = <&mc TEGRA234_MEMORY_CLIENT_PCIE4R &emc>,
+				<&mc TEGRA234_MEMORY_CLIENT_PCIE4W &emc>;
+		interconnect-names = "dma-mem", "write";
+		iommu-map = <0x0 &smmu_niso0 TEGRA234_SID_PCIE4 0x1000>;
+		iommu-map-mask = <0x0>;
+		dma-coherent;
+
+		status = "disabled";
+	};
+
+	pcie@14180000 {
+		compatible = "nvidia,tegra234-pcie";
+		power-domains = <&bpmp TEGRA234_POWER_DOMAIN_PCIEX4BA>;
+		reg = <0x00 0x14180000 0x0 0x00020000>, /* appl registers (128K)      */
+		      <0x00 0x38000000 0x0 0x00040000>, /* configuration space (256K) */
+		      <0x00 0x38040000 0x0 0x00040000>, /* iATU_DMA reg space (256K)  */
+		      <0x00 0x38080000 0x0 0x00040000>; /* DBI reg space (256K)       */
+		reg-names = "appl", "config", "atu_dma", "dbi";
+
+		#address-cells = <3>;
+		#size-cells = <2>;
+		device_type = "pci";
+		num-lanes = <4>;
+		num-viewport = <8>;
+		linux,pci-domain = <0>;
+
+		clocks = <&bpmp TEGRA234_CLK_PEX0_C0_CORE>;
+		clock-names = "core";
+
+		resets = <&bpmp TEGRA234_RESET_PEX0_CORE_0_APB>,
+			 <&bpmp TEGRA234_RESET_PEX0_CORE_0>;
+		reset-names = "apb", "core";
+
+		interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>, /* controller interrupt */
+			     <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>; /* MSI interrupt */
+		interrupt-names = "intr", "msi";
+
+		#interrupt-cells = <1>;
+		interrupt-map-mask = <0 0 0 0>;
+		interrupt-map = <0 0 0 0 &gic GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
+
+		nvidia,bpmp = <&bpmp 0>;
+
+		nvidia,aspm-cmrt-us = <60>;
+		nvidia,aspm-pwr-on-t-us = <20>;
+		nvidia,aspm-l0s-entrance-latency-us = <3>;
+
+		bus-range = <0x0 0xff>;
+
+		ranges = <0x43000000 0x24 0x40000000 0x24 0x40000000 0x2 0xe8000000>, /* prefetchable memory (11904 MB) */
+			 <0x02000000 0x0  0x40000000 0x27 0x28000000 0x0 0x08000000>, /* non-prefetchable memory (128 MB) */
+			 <0x01000000 0x0  0x38100000 0x00 0x38100000 0x0 0x00100000>; /* downstream I/O (1 MB) */
+
+		interconnects = <&mc TEGRA234_MEMORY_CLIENT_PCIE0R &emc>,
+				<&mc TEGRA234_MEMORY_CLIENT_PCIE0W &emc>;
+		interconnect-names = "dma-mem", "write";
+		iommu-map = <0x0 &smmu_niso0 TEGRA234_SID_PCIE0 0x1000>;
+		iommu-map-mask = <0x0>;
+		dma-coherent;
+
+		status = "disabled";
+	};
+
+	pcie@141a0000 {
+		compatible = "nvidia,tegra234-pcie";
+		power-domains = <&bpmp TEGRA234_POWER_DOMAIN_PCIEX8A>;
+		reg = <0x00 0x141a0000 0x0 0x00020000>, /* appl registers (128K)      */
+		      <0x00 0x3a000000 0x0 0x00040000>, /* configuration space (256K) */
+		      <0x00 0x3a040000 0x0 0x00040000>, /* iATU_DMA reg space (256K)  */
+		      <0x00 0x3a080000 0x0 0x00040000>; /* DBI reg space (256K)       */
+		reg-names = "appl", "config", "atu_dma", "dbi";
+
+		#address-cells = <3>;
+		#size-cells = <2>;
+		device_type = "pci";
+		num-lanes = <8>;
+		num-viewport = <8>;
+		linux,pci-domain = <5>;
+
+		clocks = <&bpmp TEGRA234_CLK_PEX1_C5_CORE>;
+		clock-names = "core";
+
+		resets = <&bpmp TEGRA234_RESET_PEX1_CORE_5_APB>,
+			 <&bpmp TEGRA234_RESET_PEX1_CORE_5>;
+		reset-names = "apb", "core";
+
+		interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>, /* controller interrupt */
+			     <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>; /* MSI interrupt */
+		interrupt-names = "intr", "msi";
+
+		#interrupt-cells = <1>;
+		interrupt-map-mask = <0 0 0 0>;
+		interrupt-map = <0 0 0 0 &gic GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>;
+
+		nvidia,bpmp = <&bpmp 5>;
+
+		nvidia,aspm-cmrt-us = <60>;
+		nvidia,aspm-pwr-on-t-us = <20>;
+		nvidia,aspm-l0s-entrance-latency-us = <3>;
+
+		bus-range = <0x0 0xff>;
+
+		ranges = <0x43000000 0x27 0x40000000 0x27 0x40000000 0x3 0xe8000000>, /* prefetchable memory (16000 MB) */
+			 <0x02000000 0x0  0x40000000 0x2b 0x28000000 0x0 0x08000000>, /* non-prefetchable memory (128 MB) */
+			 <0x01000000 0x0  0x3a100000 0x00 0x3a100000 0x0 0x00100000>; /* downstream I/O (1 MB) */
+
+		interconnects = <&mc TEGRA234_MEMORY_CLIENT_PCIE5R &emc>,
+				<&mc TEGRA234_MEMORY_CLIENT_PCIE5W &emc>;
+		interconnect-names = "dma-mem", "write";
+		iommu-map = <0x0 &smmu_niso0 TEGRA234_SID_PCIE5 0x1000>;
+		iommu-map-mask = <0x0>;
+		dma-coherent;
+
+		status = "disabled";
+	};
+
+	pcie@141c0000 {
+		compatible = "nvidia,tegra234-pcie";
+		power-domains = <&bpmp TEGRA234_POWER_DOMAIN_PCIEX4A>;
+		reg = <0x00 0x141c0000 0x0 0x00020000>, /* appl registers (128K)      */
+		      <0x00 0x3c000000 0x0 0x00040000>, /* configuration space (256K) */
+		      <0x00 0x3c040000 0x0 0x00040000>, /* iATU_DMA reg space (256K)  */
+		      <0x00 0x3c080000 0x0 0x00040000>; /* DBI reg space (256K)       */
+		reg-names = "appl", "config", "atu_dma", "dbi";
+
+		#address-cells = <3>;
+		#size-cells = <2>;
+		device_type = "pci";
+		num-lanes = <4>;
+		num-viewport = <8>;
+		linux,pci-domain = <6>;
+
+		clocks = <&bpmp TEGRA234_CLK_PEX1_C6_CORE>;
+		clock-names = "core";
+
+		resets = <&bpmp TEGRA234_RESET_PEX1_CORE_6_APB>,
+			 <&bpmp TEGRA234_RESET_PEX1_CORE_6>;
+		reset-names = "apb", "core";
+
+		interrupts = <GIC_SPI 352 IRQ_TYPE_LEVEL_HIGH>, /* controller interrupt */
+			     <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>; /* MSI interrupt */
+		interrupt-names = "intr", "msi";
+
+		#interrupt-cells = <1>;
+		interrupt-map-mask = <0 0 0 0>;
+		interrupt-map = <0 0 0 0 &gic GIC_SPI 352 IRQ_TYPE_LEVEL_HIGH>;
+
+		nvidia,bpmp = <&bpmp 6>;
+
+		nvidia,aspm-cmrt-us = <60>;
+		nvidia,aspm-pwr-on-t-us = <20>;
+		nvidia,aspm-l0s-entrance-latency-us = <3>;
+
+		bus-range = <0x0 0xff>;
+
+		ranges = <0x43000000 0x2b 0x40000000 0x2b 0x40000000 0x2 0xe8000000>, /* prefetchable memory (11904 MB) */
+			 <0x02000000 0x0  0x40000000 0x2e 0x28000000 0x0 0x08000000>, /* non-prefetchable memory (128 MB) */
+			 <0x01000000 0x0  0x3c100000 0x00 0x3c100000 0x0 0x00100000>; /* downstream I/O (1 MB) */
+
+		interconnects = <&mc TEGRA234_MEMORY_CLIENT_PCIE6AR &emc>,
+				<&mc TEGRA234_MEMORY_CLIENT_PCIE6AW &emc>;
+		interconnect-names = "dma-mem", "write";
+		iommu-map = <0x0 &smmu_niso0 TEGRA234_SID_PCIE6 0x1000>;
+		iommu-map-mask = <0x0>;
+		dma-coherent;
+
+		status = "disabled";
+	};
+
+	pcie@141e0000 {
+		compatible = "nvidia,tegra234-pcie";
+		power-domains = <&bpmp TEGRA234_POWER_DOMAIN_PCIEX8B>;
+		reg = <0x00 0x141e0000 0x0 0x00020000>, /* appl registers (128K)      */
+		      <0x00 0x3e000000 0x0 0x00040000>, /* configuration space (256K) */
+		      <0x00 0x3e040000 0x0 0x00040000>, /* iATU_DMA reg space (256K)  */
+		      <0x00 0x3e080000 0x0 0x00040000>; /* DBI reg space (256K)       */
+		reg-names = "appl", "config", "atu_dma", "dbi";
+
+		#address-cells = <3>;
+		#size-cells = <2>;
+		device_type = "pci";
+		num-lanes = <8>;
+		num-viewport = <8>;
+		linux,pci-domain = <7>;
+
+		clocks = <&bpmp TEGRA234_CLK_PEX2_C7_CORE>;
+		clock-names = "core";
+
+		resets = <&bpmp TEGRA234_RESET_PEX2_CORE_7_APB>,
+			 <&bpmp TEGRA234_RESET_PEX2_CORE_7>;
+		reset-names = "apb", "core";
+
+		interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>, /* controller interrupt */
+			     <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>; /* MSI interrupt */
+		interrupt-names = "intr", "msi";
+
+		#interrupt-cells = <1>;
+		interrupt-map-mask = <0 0 0 0>;
+		interrupt-map = <0 0 0 0 &gic GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
+
+		nvidia,bpmp = <&bpmp 7>;
+
+		nvidia,aspm-cmrt-us = <60>;
+		nvidia,aspm-pwr-on-t-us = <20>;
+		nvidia,aspm-l0s-entrance-latency-us = <3>;
+
+		bus-range = <0x0 0xff>;
+
+		ranges = <0x43000000 0x2e 0x40000000 0x2e 0x40000000 0x3 0xe8000000>, /* prefetchable memory (16000 MB) */
+			 <0x02000000 0x0  0x40000000 0x32 0x28000000 0x0 0x08000000>, /* non-prefetchable memory (128 MB) */
+			 <0x01000000 0x0  0x3e100000 0x00 0x3e100000 0x0 0x00100000>; /* downstream I/O (1 MB) */
+
+		interconnects = <&mc TEGRA234_MEMORY_CLIENT_PCIE7AR &emc>,
+				<&mc TEGRA234_MEMORY_CLIENT_PCIE7AW &emc>;
+		interconnect-names = "dma-mem", "write";
+		iommu-map = <0x0 &smmu_niso1 TEGRA234_SID_PCIE7 0x1000>;
+		iommu-map-mask = <0x0>;
+		dma-coherent;
+
+		status = "disabled";
+	};
+
+	pcie-ep@141a0000 {
+		compatible = "nvidia,tegra234-pcie-ep";
+		power-domains = <&bpmp TEGRA234_POWER_DOMAIN_PCIEX8A>;
+		reg = <0x00 0x141a0000 0x0 0x00020000>, /* appl registers (128K)      */
+		      <0x00 0x3a040000 0x0 0x00040000>, /* iATU_DMA reg space (256K)  */
+		      <0x00 0x3a080000 0x0 0x00040000>, /* DBI reg space (256K)       */
+		      <0x27 0x40000000 0x4 0x00000000>; /* Address Space (16G)        */
+		reg-names = "appl", "atu_dma", "dbi", "addr_space";
+
+		num-lanes = <8>;
+
+		clocks = <&bpmp TEGRA234_CLK_PEX1_C5_CORE>;
+		clock-names = "core";
+
+		resets = <&bpmp TEGRA234_RESET_PEX1_CORE_5_APB>,
+			 <&bpmp TEGRA234_RESET_PEX1_CORE_5>;
+		reset-names = "apb", "core";
+
+		interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>;	/* controller interrupt */
+		interrupt-names = "intr";
+
+		nvidia,bpmp = <&bpmp 5>;
+
+		nvidia,enable-ext-refclk;
+		nvidia,aspm-cmrt-us = <60>;
+		nvidia,aspm-pwr-on-t-us = <20>;
+		nvidia,aspm-l0s-entrance-latency-us = <3>;
+
+		interconnects = <&mc TEGRA234_MEMORY_CLIENT_PCIE5R &emc>,
+				<&mc TEGRA234_MEMORY_CLIENT_PCIE5W &emc>;
+		interconnect-names = "dma-mem", "write";
+		iommu-map = <0x0 &smmu_niso0 TEGRA234_SID_PCIE5 0x1000>;
+		iommu-map-mask = <0x0>;
+		dma-coherent;
+
+		status = "disabled";
+	};
+
+	pcie-ep@141c0000{
+		compatible = "nvidia,tegra234-pcie-ep";
+		power-domains = <&bpmp TEGRA234_POWER_DOMAIN_PCIEX4A>;
+		reg = <0x00 0x141c0000 0x0 0x00020000>, /* appl registers (128K)      */
+		      <0x00 0x3c040000 0x0 0x00040000>, /* iATU_DMA reg space (256K)  */
+		      <0x00 0x3c080000 0x0 0x00040000>, /* DBI space (256K)           */
+		      <0x2b 0x40000000 0x3 0x00000000>; /* Address Space (12G)        */
+		reg-names = "appl", "atu_dma", "dbi", "addr_space";
+
+		num-lanes = <4>;
+
+		clocks = <&bpmp TEGRA234_CLK_PEX1_C6_CORE>;
+		clock-names = "core";
+
+		resets = <&bpmp TEGRA234_RESET_PEX1_CORE_6_APB>,
+			 <&bpmp TEGRA234_RESET_PEX1_CORE_6>;
+		reset-names = "apb", "core";
+
+		interrupts = <GIC_SPI 352 IRQ_TYPE_LEVEL_HIGH>;	/* controller interrupt */
+		interrupt-names = "intr";
+
+		nvidia,bpmp = <&bpmp 6>;
+
+		nvidia,enable-ext-refclk;
+		nvidia,aspm-cmrt-us = <60>;
+		nvidia,aspm-pwr-on-t-us = <20>;
+		nvidia,aspm-l0s-entrance-latency-us = <3>;
+
+		interconnects = <&mc TEGRA234_MEMORY_CLIENT_PCIE6AR &emc>,
+				<&mc TEGRA234_MEMORY_CLIENT_PCIE6AW &emc>;
+		interconnect-names = "dma-mem", "write";
+		iommu-map = <0x0 &smmu_niso0 TEGRA234_SID_PCIE6 0x1000>;
+		iommu-map-mask = <0x0>;
+		dma-coherent;
+
+		status = "disabled";
+	};
+
+	pcie-ep@141e0000{
+		compatible = "nvidia,tegra234-pcie-ep";
+		power-domains = <&bpmp TEGRA234_POWER_DOMAIN_PCIEX8B>;
+		reg = <0x00 0x141e0000 0x0 0x00020000>, /* appl registers (128K)      */
+		      <0x00 0x3e040000 0x0 0x00040000>, /* iATU_DMA reg space (256K)  */
+		      <0x00 0x3e080000 0x0 0x00040000>, /* DBI space (256K)           */
+		      <0x2e 0x40000000 0x4 0x00000000>; /* Address Space (16G)        */
+		reg-names = "appl", "atu_dma", "dbi", "addr_space";
+
+		num-lanes = <8>;
+
+		clocks = <&bpmp TEGRA234_CLK_PEX2_C7_CORE>;
+		clock-names = "core";
+
+		resets = <&bpmp TEGRA234_RESET_PEX2_CORE_7_APB>,
+			 <&bpmp TEGRA234_RESET_PEX2_CORE_7>;
+		reset-names = "apb", "core";
+
+		interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;	/* controller interrupt */
+		interrupt-names = "intr";
+
+		nvidia,bpmp = <&bpmp 7>;
+
+		nvidia,enable-ext-refclk;
+		nvidia,aspm-cmrt-us = <60>;
+		nvidia,aspm-pwr-on-t-us = <20>;
+		nvidia,aspm-l0s-entrance-latency-us = <3>;
+
+		interconnects = <&mc TEGRA234_MEMORY_CLIENT_PCIE7AR &emc>,
+				<&mc TEGRA234_MEMORY_CLIENT_PCIE7AW &emc>;
+		interconnect-names = "dma-mem", "write";
+		iommu-map = <0x0 &smmu_niso1 TEGRA234_SID_PCIE7 0x1000>;
+		iommu-map-mask = <0x0>;
+		dma-coherent;
+
+		status = "disabled";
+	};
+
+	pcie-ep@140e0000{
+		compatible = "nvidia,tegra234-pcie-ep";
+		power-domains = <&bpmp TEGRA234_POWER_DOMAIN_PCIEX4CC>;
+		reg = <0x00 0x140e0000 0x0 0x00020000>, /* appl registers (128K)      */
+		      <0x00 0x2e040000 0x0 0x00040000>, /* iATU_DMA reg space (256K)  */
+		      <0x00 0x2e080000 0x0 0x00040000>, /* DBI space (256K)           */
+		      <0x38 0x40000000 0x3 0x00000000>; /* Address Space (12G)        */
+		reg-names = "appl", "atu_dma", "dbi", "addr_space";
+
+		num-lanes = <4>;
+
+		clocks = <&bpmp TEGRA234_CLK_PEX2_C10_CORE>;
+		clock-names = "core";
+
+		resets = <&bpmp TEGRA234_RESET_PEX2_CORE_10_APB>,
+			 <&bpmp TEGRA234_RESET_PEX2_CORE_10>;
+		reset-names = "apb", "core";
+
+		interrupts = <GIC_SPI 360 IRQ_TYPE_LEVEL_HIGH>;	/* controller interrupt */
+		interrupt-names = "intr";
+
+		nvidia,bpmp = <&bpmp 10>;
+
+		nvidia,enable-ext-refclk;
+		nvidia,aspm-cmrt-us = <60>;
+		nvidia,aspm-pwr-on-t-us = <20>;
+		nvidia,aspm-l0s-entrance-latency-us = <3>;
+
+		interconnects = <&mc TEGRA234_MEMORY_CLIENT_PCIE10AR &emc>,
+				<&mc TEGRA234_MEMORY_CLIENT_PCIE10AW &emc>;
+		interconnect-names = "dma-mem", "write";
+		iommu-map = <0x0 &smmu_niso1 TEGRA234_SID_PCIE10 0x1000>;
+		iommu-map-mask = <0x0>;
+		dma-coherent;
+
+		status = "disabled";
 	};
 
-	sysram@40000000 {
+	sram@40000000 {
 		compatible = "nvidia,tegra234-sysram", "mmio-sram";
-		reg = <0x0 0x40000000 0x0 0x50000>;
+		reg = <0x0 0x40000000 0x0 0x80000>;
 		#address-cells = <1>;
 		#size-cells = <1>;
-		ranges = <0x0 0x0 0x40000000 0x50000>;
+		ranges = <0x0 0x0 0x40000000 0x80000>;
+		no-memory-wc;
 
-		cpu_bpmp_tx: shmem@4e000 {
-			reg = <0x4e000 0x1000>;
+		cpu_bpmp_tx: sram@70000 {
+			reg = <0x70000 0x1000>;
 			label = "cpu-bpmp-tx";
 			pool;
 		};
 
-		cpu_bpmp_rx: shmem@4f000 {
-			reg = <0x4f000 0x1000>;
+		cpu_bpmp_rx: sram@71000 {
+			reg = <0x71000 0x1000>;
 			label = "cpu-bpmp-rx";
 			pool;
 		};
@@ -146,10 +2633,16 @@
 		compatible = "nvidia,tegra234-bpmp", "nvidia,tegra186-bpmp";
 		mboxes = <&hsp_top0 TEGRA_HSP_MBOX_TYPE_DB
 				    TEGRA_HSP_DB_MASTER_BPMP>;
-		shmem = <&cpu_bpmp_tx &cpu_bpmp_rx>;
+		shmem = <&cpu_bpmp_tx>, <&cpu_bpmp_rx>;
 		#clock-cells = <1>;
 		#reset-cells = <1>;
 		#power-domain-cells = <1>;
+		interconnects = <&mc TEGRA234_MEMORY_CLIENT_BPMPR &emc>,
+				<&mc TEGRA234_MEMORY_CLIENT_BPMPW &emc>,
+				<&mc TEGRA234_MEMORY_CLIENT_BPMPDMAR &emc>,
+				<&mc TEGRA234_MEMORY_CLIENT_BPMPDMAW &emc>;
+		interconnect-names = "read", "write", "dma-mem", "dma-write";
+		iommus = <&smmu_niso1 TEGRA234_SID_BPMP>;
 
 		bpmp_i2c: i2c {
 			compatible = "nvidia,tegra186-bpmp-i2c";
@@ -163,20 +2656,403 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		cpu@0 {
+		cpu0_0: cpu@0 {
+			compatible = "arm,cortex-a78";
+			device_type = "cpu";
+			reg = <0x00000>;
+
+			enable-method = "psci";
+
+			i-cache-size = <65536>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <65536>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <256>;
+			next-level-cache = <&l2c0_0>;
+		};
+
+		cpu0_1: cpu@100 {
+			compatible = "arm,cortex-a78";
+			device_type = "cpu";
+			reg = <0x00100>;
+
+			enable-method = "psci";
+
+			i-cache-size = <65536>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <65536>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <256>;
+			next-level-cache = <&l2c0_1>;
+		};
+
+		cpu0_2: cpu@200 {
+			compatible = "arm,cortex-a78";
+			device_type = "cpu";
+			reg = <0x00200>;
+
+			enable-method = "psci";
+
+			i-cache-size = <65536>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <65536>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <256>;
+			next-level-cache = <&l2c0_2>;
+		};
+
+		cpu0_3: cpu@300 {
+			compatible = "arm,cortex-a78";
+			device_type = "cpu";
+			reg = <0x00300>;
+
+			enable-method = "psci";
+
+			i-cache-size = <65536>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <65536>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <256>;
+			next-level-cache = <&l2c0_3>;
+		};
+
+		cpu1_0: cpu@10000 {
+			compatible = "arm,cortex-a78";
+			device_type = "cpu";
+			reg = <0x10000>;
+
+			enable-method = "psci";
+
+			i-cache-size = <65536>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <65536>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <256>;
+			next-level-cache = <&l2c1_0>;
+		};
+
+		cpu1_1: cpu@10100 {
+			compatible = "arm,cortex-a78";
+			device_type = "cpu";
+			reg = <0x10100>;
+
+			enable-method = "psci";
+
+			i-cache-size = <65536>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <65536>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <256>;
+			next-level-cache = <&l2c1_1>;
+		};
+
+		cpu1_2: cpu@10200 {
+			compatible = "arm,cortex-a78";
 			device_type = "cpu";
-			reg = <0x000>;
+			reg = <0x10200>;
 
 			enable-method = "psci";
+
+			i-cache-size = <65536>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <65536>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <256>;
+			next-level-cache = <&l2c1_2>;
+		};
+
+		cpu1_3: cpu@10300 {
+			compatible = "arm,cortex-a78";
+			device_type = "cpu";
+			reg = <0x10300>;
+
+			enable-method = "psci";
+
+			i-cache-size = <65536>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <65536>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <256>;
+			next-level-cache = <&l2c1_3>;
+		};
+
+		cpu2_0: cpu@20000 {
+			compatible = "arm,cortex-a78";
+			device_type = "cpu";
+			reg = <0x20000>;
+
+			enable-method = "psci";
+
+			i-cache-size = <65536>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <65536>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <256>;
+			next-level-cache = <&l2c2_0>;
+		};
+
+		cpu2_1: cpu@20100 {
+			compatible = "arm,cortex-a78";
+			device_type = "cpu";
+			reg = <0x20100>;
+
+			enable-method = "psci";
+
+			i-cache-size = <65536>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <65536>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <256>;
+			next-level-cache = <&l2c2_1>;
+		};
+
+		cpu2_2: cpu@20200 {
+			compatible = "arm,cortex-a78";
+			device_type = "cpu";
+			reg = <0x20200>;
+
+			enable-method = "psci";
+
+			i-cache-size = <65536>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <65536>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <256>;
+			next-level-cache = <&l2c2_2>;
+		};
+
+		cpu2_3: cpu@20300 {
+			compatible = "arm,cortex-a78";
+			device_type = "cpu";
+			reg = <0x20300>;
+
+			enable-method = "psci";
+
+			i-cache-size = <65536>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <65536>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <256>;
+			next-level-cache = <&l2c2_3>;
+		};
+
+		cpu-map {
+			cluster0 {
+				core0 {
+					cpu = <&cpu0_0>;
+				};
+
+				core1 {
+					cpu = <&cpu0_1>;
+				};
+
+				core2 {
+					cpu = <&cpu0_2>;
+				};
+
+				core3 {
+					cpu = <&cpu0_3>;
+				};
+			};
+
+			cluster1 {
+				core0 {
+					cpu = <&cpu1_0>;
+				};
+
+				core1 {
+					cpu = <&cpu1_1>;
+				};
+
+				core2 {
+					cpu = <&cpu1_2>;
+				};
+
+				core3 {
+					cpu = <&cpu1_3>;
+				};
+			};
+
+			cluster2 {
+				core0 {
+					cpu = <&cpu2_0>;
+				};
+
+				core1 {
+					cpu = <&cpu2_1>;
+				};
+
+				core2 {
+					cpu = <&cpu2_2>;
+				};
+
+				core3 {
+					cpu = <&cpu2_3>;
+				};
+			};
+		};
+
+		l2c0_0: l2-cache00 {
+			cache-size = <262144>;
+			cache-line-size = <64>;
+			cache-sets = <512>;
+			cache-unified;
+			next-level-cache = <&l3c0>;
+		};
+
+		l2c0_1: l2-cache01 {
+			cache-size = <262144>;
+			cache-line-size = <64>;
+			cache-sets = <512>;
+			cache-unified;
+			next-level-cache = <&l3c0>;
+		};
+
+		l2c0_2: l2-cache02 {
+			cache-size = <262144>;
+			cache-line-size = <64>;
+			cache-sets = <512>;
+			cache-unified;
+			next-level-cache = <&l3c0>;
+		};
+
+		l2c0_3: l2-cache03 {
+			cache-size = <262144>;
+			cache-line-size = <64>;
+			cache-sets = <512>;
+			cache-unified;
+			next-level-cache = <&l3c0>;
+		};
+
+		l2c1_0: l2-cache10 {
+			cache-size = <262144>;
+			cache-line-size = <64>;
+			cache-sets = <512>;
+			cache-unified;
+			next-level-cache = <&l3c1>;
+		};
+
+		l2c1_1: l2-cache11 {
+			cache-size = <262144>;
+			cache-line-size = <64>;
+			cache-sets = <512>;
+			cache-unified;
+			next-level-cache = <&l3c1>;
+		};
+
+		l2c1_2: l2-cache12 {
+			cache-size = <262144>;
+			cache-line-size = <64>;
+			cache-sets = <512>;
+			cache-unified;
+			next-level-cache = <&l3c1>;
+		};
+
+		l2c1_3: l2-cache13 {
+			cache-size = <262144>;
+			cache-line-size = <64>;
+			cache-sets = <512>;
+			cache-unified;
+			next-level-cache = <&l3c1>;
+		};
+
+		l2c2_0: l2-cache20 {
+			cache-size = <262144>;
+			cache-line-size = <64>;
+			cache-sets = <512>;
+			cache-unified;
+			next-level-cache = <&l3c2>;
+		};
+
+		l2c2_1: l2-cache21 {
+			cache-size = <262144>;
+			cache-line-size = <64>;
+			cache-sets = <512>;
+			cache-unified;
+			next-level-cache = <&l3c2>;
+		};
+
+		l2c2_2: l2-cache22 {
+			cache-size = <262144>;
+			cache-line-size = <64>;
+			cache-sets = <512>;
+			cache-unified;
+			next-level-cache = <&l3c2>;
+		};
+
+		l2c2_3: l2-cache23 {
+			cache-size = <262144>;
+			cache-line-size = <64>;
+			cache-sets = <512>;
+			cache-unified;
+			next-level-cache = <&l3c2>;
+		};
+
+		l3c0: l3-cache0 {
+			cache-size = <2097152>;
+			cache-line-size = <64>;
+			cache-sets = <2048>;
+		};
+
+		l3c1: l3-cache1 {
+			cache-size = <2097152>;
+			cache-line-size = <64>;
+			cache-sets = <2048>;
+		};
+
+		l3c2: l3-cache2 {
+			cache-size = <2097152>;
+			cache-line-size = <64>;
+			cache-sets = <2048>;
 		};
 	};
 
+	pmu {
+		compatible = "arm,cortex-a78-pmu";
+		interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH>;
+		status = "okay";
+	};
+
 	psci {
 		compatible = "arm,psci-1.0";
 		status = "okay";
 		method = "smc";
 	};
 
+	tcu: serial {
+		compatible = "nvidia,tegra234-tcu", "nvidia,tegra194-tcu";
+		mboxes = <&hsp_top0 TEGRA_HSP_MBOX_TYPE_SM TEGRA_HSP_SM_RX(0)>,
+			 <&hsp_aon TEGRA_HSP_MBOX_TYPE_SM TEGRA_HSP_SM_TX(1)>;
+		mbox-names = "rx", "tx";
+		status = "disabled";
+	};
+
+	sound {
+		status = "disabled";
+
+		clocks = <&bpmp TEGRA234_CLK_PLLA>,
+			 <&bpmp TEGRA234_CLK_PLLA_OUT0>;
+		clock-names = "pll_a", "plla_out0";
+		assigned-clocks = <&bpmp TEGRA234_CLK_PLLA>,
+				  <&bpmp TEGRA234_CLK_PLLA_OUT0>,
+				  <&bpmp TEGRA234_CLK_AUD_MCLK>;
+		assigned-clock-parents = <0>,
+					 <&bpmp TEGRA234_CLK_PLLA>,
+					 <&bpmp TEGRA234_CLK_PLLA_OUT0>;
+	};
+
 	timer {
 		compatible = "arm,armv8-timer";
 		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 6b816eb33309..d7669a7cee9f 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -15,12 +15,17 @@ dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-longcheer-l8910.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-mtp.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-samsung-a3u-eur.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-samsung-a5u-eur.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-samsung-e5.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-samsung-e7.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-samsung-grandmax.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-samsung-j5.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-samsung-serranove.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-wingtech-wt88047.dtb
-dtb-$(CONFIG_ARCH_QCOM)	+= msm8992-bullhead-rev-101.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= msm8992-lg-bullhead-rev-10.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= msm8992-lg-bullhead-rev-101.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8992-msft-lumia-octagon-talkman.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8992-xiaomi-libra.dtb
-dtb-$(CONFIG_ARCH_QCOM)	+= msm8994-angler-rev-101.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= msm8994-huawei-angler-rev-101.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8994-msft-lumia-octagon-cityman.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8994-sony-xperia-kitakami-ivy.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8994-sony-xperia-kitakami-karin.dtb
@@ -28,13 +33,11 @@ dtb-$(CONFIG_ARCH_QCOM)	+= msm8994-sony-xperia-kitakami-satsuki.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8994-sony-xperia-kitakami-sumire.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8994-sony-xperia-kitakami-suzuran.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8996-mtp.dtb
-dtb-$(CONFIG_ARCH_QCOM)	+= msm8996-pmi8996-sony-xperia-tone-dora.dtb
-dtb-$(CONFIG_ARCH_QCOM)	+= msm8996-pmi8996-sony-xperia-tone-kagura.dtb
-dtb-$(CONFIG_ARCH_QCOM)	+= msm8996-pmi8996-sony-xperia-tone-keyaki.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8996-sony-xperia-tone-dora.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8996-sony-xperia-tone-kagura.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8996-sony-xperia-tone-keyaki.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8996-xiaomi-gemini.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= msm8996-xiaomi-natrium.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8996-xiaomi-scorpio.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8998-asus-novago-tp370ql.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8998-fxtec-pro1.dtb
@@ -50,6 +53,7 @@ dtb-$(CONFIG_ARCH_QCOM)	+= qcs404-evb-1000.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= qcs404-evb-4000.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= qrb5165-rb5.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sa8155p-adp.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sa8295p-adp.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-idp.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-coachz-r1.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-coachz-r1-lte.dtb
@@ -57,6 +61,9 @@ dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-coachz-r3.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-coachz-r3-lte.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-homestar-r2.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-homestar-r3.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-homestar-r4.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-kingoftown-r0.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-kingoftown-r1.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-lazor-r0.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-lazor-r1.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-lazor-r1-kb.dtb
@@ -64,35 +71,74 @@ dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-lazor-r1-lte.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-lazor-r3.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-lazor-r3-kb.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-lazor-r3-lte.dtb
-dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-lazor-limozeen.dtb
-dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-lazor-limozeen-nots.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-lazor-r9.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-lazor-r9-kb.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-lazor-r9-lte.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-lazor-limozeen-r4.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-lazor-limozeen-r9.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-lazor-limozeen-nots-r4.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-lazor-limozeen-nots-r5.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-lazor-limozeen-nots-r9.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-mrbland-rev0-auo.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-mrbland-rev0-boe.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-mrbland-rev1-auo.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-mrbland-rev1-boe.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-pazquel-lte-parade.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-pazquel-lte-ti.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-pazquel-parade.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-pazquel-ti.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-pompom-r1.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-pompom-r1-lte.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-pompom-r2.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-pompom-r2-lte.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-pompom-r3.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-pompom-r3-lte.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-quackingstick-r0.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-quackingstick-r0-lte.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-wormdingler-rev0-boe.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-wormdingler-rev0-inx.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-wormdingler-rev1-boe.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-wormdingler-rev1-inx.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-wormdingler-rev1-inx-rt5682s.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-wormdingler-rev1-boe-rt5682s.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-r1.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-r1-lte.dtb
-dtb-$(CONFIG_ARCH_QCOM)	+= sc7280-herobrine.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sc7280-herobrine-crd.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sc7280-herobrine-evoker-r0.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sc7280-herobrine-herobrine-r1.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sc7280-herobrine-villager-r0.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sc7280-herobrine-villager-r1.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sc7280-herobrine-villager-r1-lte.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7280-idp.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sc7280-idp2.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sc7280-crd-r3.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sc8280xp-crd.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sc8280xp-lenovo-thinkpad-x13s.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sda660-inforce-ifc6560.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm630-sony-xperia-ganges-kirin.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm630-sony-xperia-nile-discovery.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm630-sony-xperia-nile-pioneer.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm630-sony-xperia-nile-voyager.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sdm632-fairphone-fp3.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm636-sony-xperia-ganges-mermaid.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm660-xiaomi-lavender.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-cheza-r1.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-cheza-r2.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-cheza-r3.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-db845c.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-lg-judyln.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-lg-judyp.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-mtp.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-oneplus-enchilada.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-oneplus-fajita.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-sony-xperia-tama-akari.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-sony-xperia-tama-akatsuki.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-sony-xperia-tama-apollo.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-xiaomi-beryllium.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-xiaomi-polaris.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sdm845-shift-axolotl.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sdm850-lenovo-yoga-c630.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sdm850-samsung-w737.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm6125-sony-xperia-seine-pdx201.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm6350-sony-xperia-lena-pdx213.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm7225-fairphone-fp4.dtb
@@ -106,4 +152,10 @@ dtb-$(CONFIG_ARCH_QCOM)	+= sm8250-mtp.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm8250-sony-xperia-edo-pdx203.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm8250-sony-xperia-edo-pdx206.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm8350-hdk.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sm8350-microsoft-surface-duo2.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm8350-mtp.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sm8350-sony-xperia-sagami-pdx214.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sm8350-sony-xperia-sagami-pdx215.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sm8450-hdk.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sm8450-qrd.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sm8450-sony-xperia-nagara-pdx223.dtb
diff --git a/arch/arm64/boot/dts/qcom/apq8016-sbc.dts b/arch/arm64/boot/dts/qcom/apq8016-sbc.dts
index a5320d6d30e7..1b613098fb4a 100644
--- a/arch/arm64/boot/dts/qcom/apq8016-sbc.dts
+++ b/arch/arm64/boot/dts/qcom/apq8016-sbc.dts
@@ -8,6 +8,7 @@
 #include "msm8916-pm8916.dtsi"
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
 #include <dt-bindings/pinctrl/qcom,pmic-mpp.h>
 #include <dt-bindings/sound/apq8016-lpass.h>
@@ -20,11 +21,11 @@
 		serial0 = &blsp1_uart2;
 		serial1 = &blsp1_uart1;
 		usid0 = &pm8916_0;
-		i2c0	= &blsp_i2c2;
-		i2c1	= &blsp_i2c6;
-		i2c3	= &blsp_i2c4;
-		spi0	= &blsp_spi5;
-		spi1	= &blsp_spi3;
+		i2c0 = &blsp_i2c2;
+		i2c1 = &blsp_i2c6;
+		i2c3 = &blsp_i2c4;
+		spi0 = &blsp_spi5;
+		spi1 = &blsp_spi3;
 	};
 
 	chosen {
@@ -92,14 +93,12 @@
 
 	gpio-keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		autorepeat;
 
 		pinctrl-names = "default";
 		pinctrl-0 = <&msm_key_volp_n_default>;
 
-		button@0 {
+		button {
 			label = "Volume Up";
 			linux,code = <KEY_VOLUMEUP>;
 			gpios = <&msmgpio 107 GPIO_ACTIVE_LOW>;
@@ -116,6 +115,8 @@
 
 		led@1 {
 			label = "apq8016-sbc:green:user1";
+			function = LED_FUNCTION_HEARTBEAT;
+			color = <LED_COLOR_ID_GREEN>;
 			gpios = <&msmgpio 21 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "heartbeat";
 			default-state = "off";
@@ -123,6 +124,8 @@
 
 		led@2 {
 			label = "apq8016-sbc:green:user2";
+			function = LED_FUNCTION_DISK_ACTIVITY;
+			color = <LED_COLOR_ID_GREEN>;
 			gpios = <&msmgpio 120 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "mmc0";
 			default-state = "off";
@@ -130,6 +133,8 @@
 
 		led@3 {
 			label = "apq8016-sbc:green:user3";
+			function = LED_FUNCTION_DISK_ACTIVITY;
+			color = <LED_COLOR_ID_GREEN>;
 			gpios = <&pm8916_gpios 1 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "mmc1";
 			default-state = "off";
@@ -137,6 +142,7 @@
 
 		led@4 {
 			label = "apq8016-sbc:green:user4";
+			color = <LED_COLOR_ID_GREEN>;
 			gpios = <&pm8916_gpios 2 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "none";
 			panic-indicator;
@@ -145,6 +151,8 @@
 
 		led@5 {
 			label = "apq8016-sbc:yellow:wlan";
+			function = LED_FUNCTION_WLAN;
+			color = <LED_COLOR_ID_YELLOW>;
 			gpios = <&pm8916_mpps 2 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "phy0tx";
 			default-state = "off";
@@ -152,6 +160,8 @@
 
 		led@6 {
 			label = "apq8016-sbc:blue:bt";
+			function = LED_FUNCTION_BLUETOOTH;
+			color = <LED_COLOR_ID_BLUE>;
 			gpios = <&pm8916_mpps 3 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "bluetooth-power";
 			default-state = "off";
@@ -253,7 +263,6 @@
 		port@0 {
 			reg = <0>;
 			csiphy0_ep: endpoint {
-				clock-lanes = <1>;
 				data-lanes = <0 2>;
 				remote-endpoint = <&ov5640_ep>;
 				status = "okay";
@@ -289,7 +298,6 @@
 
 		port {
 			ov5640_ep: endpoint {
-				clock-lanes = <1>;
 				data-lanes = <0 2>;
 				remote-endpoint = <&csiphy0_ep>;
 			};
@@ -351,12 +359,12 @@
 	pinctrl-0 = <&cdc_pdm_lines_act &ext_sec_tlmm_lines_act &ext_mclk_tlmm_lines_act>;
 	pinctrl-1 = <&cdc_pdm_lines_sus &ext_sec_tlmm_lines_sus &ext_mclk_tlmm_lines_sus>;
 	pinctrl-names = "default", "sleep";
-	qcom,model = "DB410c";
-	qcom,audio-routing =
+	model = "DB410c";
+	audio-routing =
 		"AMIC2", "MIC BIAS Internal2",
 		"AMIC3", "MIC BIAS External1";
 
-	external-dai-link@0 {
+	quaternary-dai-link {
 		link-name = "ADV7533";
 		cpu {
 			sound-dai = <&lpass MI2S_QUATERNARY>;
@@ -366,7 +374,7 @@
 		};
 	};
 
-	internal-codec-playback-dai-link@0 {
+	primary-dai-link {
 		link-name = "WCD";
 		cpu {
 			sound-dai = <&lpass MI2S_PRIMARY>;
@@ -376,7 +384,7 @@
 		};
 	};
 
-	internal-codec-capture-dai-link@0 {
+	tertiary-dai-link {
 		link-name = "WCD-Capture";
 		cpu {
 			sound-dai = <&lpass MI2S_TERTIARY>;
@@ -775,7 +783,7 @@
 		"USB_HUB_RESET_N_PM",
 		"USB_SW_SEL_PM";
 
-	usb_hub_reset_pm: usb-hub-reset-pm {
+	usb_hub_reset_pm: usb-hub-reset-pm-state {
 		pins = "gpio3";
 		function = PMIC_GPIO_FUNC_NORMAL;
 
@@ -783,14 +791,14 @@
 		output-high;
 	};
 
-	usb_hub_reset_pm_device: usb-hub-reset-pm-device {
+	usb_hub_reset_pm_device: usb-hub-reset-pm-device-state {
 		pins = "gpio3";
 		function = PMIC_GPIO_FUNC_NORMAL;
 
 		output-low;
 	};
 
-	usb_sw_sel_pm: usb-sw-sel-pm {
+	usb_sw_sel_pm: usb-sw-sel-pm-state {
 		pins = "gpio4";
 		function = PMIC_GPIO_FUNC_NORMAL;
 
@@ -799,7 +807,7 @@
 		output-high;
 	};
 
-	usb_sw_sel_pm_device: usb-sw-sel-pm-device {
+	usb_sw_sel_pm_device: usb-sw-sel-pm-device-state {
 		pins = "gpio4";
 		function = PMIC_GPIO_FUNC_NORMAL;
 
@@ -808,7 +816,7 @@
 		output-low;
 	};
 
-	pm8916_gpios_leds: pm8916-gpios-leds {
+	pm8916_gpios_leds: pm8916-gpios-leds-state {
 		pins = "gpio1", "gpio2";
 		function = PMIC_GPIO_FUNC_NORMAL;
 
diff --git a/arch/arm64/boot/dts/qcom/apq8096-db820c.dts b/arch/arm64/boot/dts/qcom/apq8096-db820c.dts
index d01a512634cf..5cdc7ac1a9c0 100644
--- a/arch/arm64/boot/dts/qcom/apq8096-db820c.dts
+++ b/arch/arm64/boot/dts/qcom/apq8096-db820c.dts
@@ -10,9 +10,11 @@
 #include "pmi8994.dtsi"
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
 #include <dt-bindings/sound/qcom,q6afe.h>
 #include <dt-bindings/sound/qcom,q6asm.h>
+#include <dt-bindings/sound/qcom,wcd9335.h>
 
 /*
  * GPIO name legend: proper name = the GPIO line is used as GPIO
@@ -49,11 +51,11 @@
 		serial0 = &blsp2_uart2;
 		serial1 = &blsp2_uart3;
 		serial2 = &blsp1_uart2;
-		i2c0	= &blsp1_i2c3;
-		i2c1	= &blsp2_i2c1;
-		i2c2	= &blsp2_i2c1;
-		spi0	= &blsp1_spi1;
-		spi1	= &blsp2_spi6;
+		i2c0 = &blsp1_i2c3;
+		i2c1 = &blsp2_i2c1;
+		i2c2 = &blsp2_i2c1;
+		spi0 = &blsp1_spi1;
+		spi1 = &blsp2_spi6;
 	};
 
 	chosen {
@@ -82,16 +84,14 @@
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		autorepeat;
 
 		pinctrl-names = "default";
 		pinctrl-0 = <&volume_up_gpio>;
 
-		button@0 {
+		button {
 			label = "Volume Up";
 			linux,code = <KEY_VOLUMEUP>;
 			gpios = <&pm8994_gpios 2 GPIO_ACTIVE_LOW>;
@@ -166,6 +166,7 @@
 
 &adsp_pil {
 	status = "okay";
+	firmware-name = "qcom/apq8096/adsp.mbn";
 };
 
 &blsp2_i2c1 {
@@ -232,6 +233,7 @@
 &hsusb_phy1 {
 	status = "okay";
 
+	vdd-supply = <&vreg_l28a_0p925>;
 	vdda-pll-supply = <&vreg_l12a_1p8>;
 	vdda-phy-dpdm-supply = <&vreg_l24a_3p075>;
 };
@@ -239,6 +241,7 @@
 &hsusb_phy2 {
 	status = "okay";
 
+	vdd-supply = <&vreg_l28a_0p925>;
 	vdda-pll-supply = <&vreg_l12a_1p8>;
 	vdda-phy-dpdm-supply = <&vreg_l24a_3p075>;
 };
@@ -255,6 +258,12 @@
 	vdd-gfx-supply = <&vdd_gfx>;
 };
 
+&mss_pil {
+	status = "okay";
+	pll-supply = <&vreg_l12a_1p8>;
+	firmware-name = "qcom/apq8096/mba.mbn", "qcom/apq8096/modem.mbn";
+};
+
 &pm8994_resin {
 	status = "okay";
 	linux,code = <KEY_VOLUMEDOWN>;
@@ -494,20 +503,20 @@
 
 &pcie0 {
 	status = "okay";
-	perst-gpio = <&tlmm 35 GPIO_ACTIVE_LOW>;
+	perst-gpios = <&tlmm 35 GPIO_ACTIVE_LOW>;
 	vddpe-3v3-supply = <&wlan_en>;
 	vdda-supply = <&vreg_l28a_0p925>;
 };
 
 &pcie1 {
 	status = "okay";
-	perst-gpio = <&tlmm 130 GPIO_ACTIVE_LOW>;
+	perst-gpios = <&tlmm 130 GPIO_ACTIVE_LOW>;
 	vdda-supply = <&vreg_l28a_0p925>;
 };
 
 &pcie2 {
 	status = "okay";
-	perst-gpio = <&tlmm 114 GPIO_ACTIVE_LOW>;
+	perst-gpios = <&tlmm 114 GPIO_ACTIVE_LOW>;
 	vdda-supply = <&vreg_l28a_0p925>;
 };
 
@@ -546,15 +555,16 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&ls_exp_gpio_f &bt_en_gpios>;
 
-	ls_exp_gpio_f: pm8994_gpio5 {
+	ls_exp_gpio_f: pm8994-gpio5-state {
 		pinconf {
 			pins = "gpio5";
+			function = PMIC_GPIO_FUNC_NORMAL;
 			output-low;
 			power-source = <2>; // PM8994_GPIO_S4, 1.8V
 		};
 	};
 
-	bt_en_gpios: bt_en_gpios {
+	bt_en_gpios: bt-en-pios-state {
 		pinconf {
 			pins = "gpio19";
 			function = PMIC_GPIO_FUNC_NORMAL;
@@ -565,7 +575,7 @@
 		};
 	};
 
-	wlan_en_gpios: wlan_en_gpios {
+	wlan_en_gpios: wlan-en-gpios-state {
 		pinconf {
 			pins = "gpio8";
 			function = PMIC_GPIO_FUNC_NORMAL;
@@ -576,7 +586,7 @@
 		};
 	};
 
-	audio_mclk: clk_div1 {
+	audio_mclk: clk-div1-state {
 		pinconf {
 			pins = "gpio15";
 			function = "func1";
@@ -584,7 +594,7 @@
 		};
 	};
 
-	volume_up_gpio: pm8996_gpio2 {
+	volume_up_gpio: pm8996-gpio2-state {
 		pinconf {
 			pins = "gpio2";
 			function = "normal";
@@ -596,7 +606,7 @@
 		};
 	};
 
-	divclk4_pin_a: divclk4 {
+	divclk4_pin_a: divclk4-state {
 		pinconf {
 			pins = "gpio18";
 			function = PMIC_GPIO_FUNC_FUNC2;
@@ -606,7 +616,7 @@
 		};
 	};
 
-	usb3_vbus_det_gpio: pm8996_gpio22 {
+	usb3_vbus_det_gpio: pm8996-gpio22-state {
 		pinconf {
 			pins = "gpio22";
 			function = PMIC_GPIO_FUNC_NORMAL;
@@ -632,6 +642,8 @@
 
 &pm8994_spmi_regulators {
 	qcom,saw-reg = <&saw3>;
+	vdd_s11-supply = <&vph_pwr>;
+
 	s9 {
 		qcom,saw-slave;
 	};
@@ -640,6 +652,7 @@
 	};
 	s11 {
 		qcom,saw-leader;
+		regulator-name = "VDD_APCC";
 		regulator-always-on;
 		regulator-min-microvolt = <980000>;
 		regulator-max-microvolt = <980000>;
@@ -659,7 +672,7 @@
 		"NC",
 		"NC";
 
-	usb2_vbus_det_gpio: pmi8996_gpio6 {
+	usb2_vbus_det_gpio: pmi8996-gpio6-state {
 		pinconf {
 			pins = "gpio6";
 			function = PMIC_GPIO_FUNC_NORMAL;
@@ -671,7 +684,64 @@
 	};
 };
 
+&pmi8994_lpg {
+	qcom,power-source = <1>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&pmi8994_mpp2_userled4>;
+
+	qcom,dtest = <0 0>,
+		     <0 0>,
+		     <0 0>,
+		     <4 1>;
+
+	status = "okay";
+
+	led@1 {
+		reg = <1>;
+		color = <LED_COLOR_ID_GREEN>;
+		function = LED_FUNCTION_HEARTBEAT;
+		function-enumerator = <1>;
+
+		linux,default-trigger = "heartbeat";
+		default-state = "on";
+	};
+
+	led@2 {
+		reg = <2>;
+		color = <LED_COLOR_ID_GREEN>;
+		function = LED_FUNCTION_HEARTBEAT;
+		function-enumerator = <0>;
+	};
+
+	led@3 {
+		reg = <3>;
+		color = <LED_COLOR_ID_GREEN>;
+		function = LED_FUNCTION_HEARTBEAT;
+		function-enumerator = <2>;
+	};
+
+	led@4 {
+		reg = <4>;
+		color = <LED_COLOR_ID_GREEN>;
+		function = LED_FUNCTION_HEARTBEAT;
+		function-enumerator = <3>;
+	};
+};
+
+&pmi8994_mpps {
+	pmi8994_mpp2_userled4: mpp2-userled4-state {
+		pins = "mpp2";
+		function = "sink";
+
+		output-low;
+		qcom,dtest = <4>;
+	};
+};
+
 &pmi8994_spmi_regulators {
+	vdd_s2-supply = <&vph_pwr>;
+
 	vdd_gfx: s2@1700 {
 		reg = <0x1700 0x100>;
 		regulator-name = "VDD_GFX";
@@ -709,7 +779,7 @@
 		vdd_l17_l29-supply = <&vph_pwr_bbyp>;
 		vdd_l20_l21-supply = <&vph_pwr_bbyp>;
 		vdd_l25-supply = <&vreg_s3a_1p3>;
-		vdd_lvs1_lvs2-supply = <&vreg_s4a_1p8>;
+		vdd_lvs1_2-supply = <&vreg_s4a_1p8>;
 
 		vreg_s3a_1p3: s3 {
 			regulator-name = "vreg_s3a_1p3";
@@ -943,7 +1013,7 @@
 &sound {
 	compatible = "qcom,apq8096-sndcard";
 	model = "DB820c";
-	audio-routing =	"RX_BIAS", "MCLK",
+	audio-routing = "RX_BIAS", "MCLK",
 		"MM_DL1",  "MultiMedia1 Playback",
 		"MM_DL2",  "MultiMedia2 Playback",
 		"MultiMedia3 Capture", "MM_UL3";
@@ -995,7 +1065,7 @@
 	};
 
 		codec {
-			sound-dai = <&wcd9335 6>;
+			sound-dai = <&wcd9335 AIF4_PB>;
 		};
 	};
 
@@ -1010,7 +1080,7 @@
 		};
 
 		codec {
-			sound-dai = <&wcd9335 1>;
+			sound-dai = <&wcd9335 AIF1_CAP>;
 		};
 	};
 };
@@ -1038,22 +1108,22 @@
 &usb2 {
 	status = "okay";
 	extcon = <&usb2_id>;
+};
 
-	dwc3@7600000 {
-		extcon = <&usb2_id>;
-		dr_mode = "otg";
-		maximum-speed = "high-speed";
-	};
+&usb2_dwc3 {
+	extcon = <&usb2_id>;
+	dr_mode = "otg";
+	maximum-speed = "high-speed";
 };
 
 &usb3 {
 	status = "okay";
 	extcon = <&usb3_id>;
+};
 
-	dwc3@6a00000 {
-		extcon = <&usb3_id>;
-		dr_mode = "otg";
-	};
+&usb3_dwc3 {
+	extcon = <&usb3_id>;
+	dr_mode = "otg";
 };
 
 &usb3phy {
diff --git a/arch/arm64/boot/dts/qcom/apq8096-ifc6640.dts b/arch/arm64/boot/dts/qcom/apq8096-ifc6640.dts
index 567b33106556..92f264891d84 100644
--- a/arch/arm64/boot/dts/qcom/apq8096-ifc6640.dts
+++ b/arch/arm64/boot/dts/qcom/apq8096-ifc6640.dts
@@ -368,7 +368,7 @@
 
 	bus-width = <4>;
 
-	cd-gpios = <&tlmm 38 0x1>;
+	cd-gpios = <&tlmm 38 GPIO_ACTIVE_LOW>;
 
 	vmmc-supply = <&vreg_l21a_2p95>;
 	vqmmc-supply = <&vreg_l13a_2p95>;
diff --git a/arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts b/arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts
index 5aec18308712..1ba2eca33c7b 100644
--- a/arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts
+++ b/arch/arm64/boot/dts/qcom/ipq6018-cp01-c1.dts
@@ -29,21 +29,21 @@
 	status = "okay";
 };
 
-&i2c_1 {
+&blsp1_i2c3 {
 	pinctrl-0 = <&i2c_1_pins>;
 	pinctrl-names = "default";
 	status = "okay";
 };
 
-&spi_0 {
+&blsp1_spi1 {
 	cs-select = <0>;
 	status = "okay";
 
-	m25p80@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		reg = <0>;
-		compatible = "n25q128a11";
+		compatible = "micron,n25q128a11", "jedec,spi-nor";
 		spi-max-frequency = <50000000>;
 	};
 };
diff --git a/arch/arm64/boot/dts/qcom/ipq6018.dtsi b/arch/arm64/boot/dts/qcom/ipq6018.dtsi
index 933b56103a46..a7c7ca980a71 100644
--- a/arch/arm64/boot/dts/qcom/ipq6018.dtsi
+++ b/arch/arm64/boot/dts/qcom/ipq6018.dtsi
@@ -87,7 +87,7 @@
 		};
 	};
 
-	cpu_opp_table: cpu_opp_table {
+	cpu_opp_table: opp-table-cpu {
 		compatible = "operating-points-v2";
 		opp-shared;
 
@@ -125,16 +125,10 @@
 
 	firmware {
 		scm {
-			compatible = "qcom,scm";
+			compatible = "qcom,scm-ipq6018", "qcom,scm";
 		};
 	};
 
-	tcsr_mutex: hwlock {
-		compatible = "qcom,tcsr-mutex";
-		syscon = <&tcsr_mutex_regs 0 0x80>;
-		#hwlock-cells = <1>;
-	};
-
 	pmuv8: pmu {
 		compatible = "arm,cortex-a53-pmu";
 		interrupts = <GIC_PPI 7 (GIC_CPU_MASK_SIMPLE(4) |
@@ -220,7 +214,7 @@
 			interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
 			gpio-controller;
 			#gpio-cells = <2>;
-			gpio-ranges = <&tlmm 0 80>;
+			gpio-ranges = <&tlmm 0 0 80>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
 
@@ -252,13 +246,14 @@
 			#reset-cells = <1>;
 		};
 
-		tcsr_mutex_regs: syscon@1905000 {
-			compatible = "syscon";
-			reg = <0x0 0x01905000 0x0 0x8000>;
+		tcsr_mutex: hwlock@1905000 {
+			compatible = "qcom,ipq6018-tcsr-mutex", "qcom,tcsr-mutex";
+			reg = <0x0 0x01905000 0x0 0x1000>;
+			#hwlock-cells = <1>;
 		};
 
 		tcsr: syscon@1937000 {
-			compatible = "syscon";
+			compatible = "qcom,tcsr-ipq6018", "syscon";
 			reg = <0x0 0x01937000 0x0 0x21000>;
 		};
 
@@ -282,7 +277,7 @@
 			status = "disabled";
 		};
 
-		spi_0: spi@78b5000 {
+		blsp1_spi1: spi@78b5000 {
 			compatible = "qcom,spi-qup-v2.2.1";
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -297,7 +292,7 @@
 			status = "disabled";
 		};
 
-		spi_1: spi@78b6000 {
+		blsp1_spi2: spi@78b6000 {
 			compatible = "qcom,spi-qup-v2.2.1";
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -312,33 +307,33 @@
 			status = "disabled";
 		};
 
-		i2c_0: i2c@78b6000 {
+		blsp1_i2c2: i2c@78b6000 {
 			compatible = "qcom,i2c-qup-v2.2.1";
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <0x0 0x078b6000 0x0 0x600>;
 			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc GCC_BLSP1_AHB_CLK>,
-				<&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>;
-			clock-names = "iface", "core";
-			clock-frequency  = <400000>;
-			dmas = <&blsp_dma 15>, <&blsp_dma 14>;
-			dma-names = "rx", "tx";
+			clocks = <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			clock-frequency = <400000>;
+			dmas = <&blsp_dma 14>, <&blsp_dma 15>;
+			dma-names = "tx", "rx";
 			status = "disabled";
 		};
 
-		i2c_1: i2c@78b7000 { /* BLSP1 QUP2 */
+		blsp1_i2c3: i2c@78b7000 {
 			compatible = "qcom,i2c-qup-v2.2.1";
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <0x0 0x078b7000 0x0 0x600>;
 			interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc GCC_BLSP1_AHB_CLK>,
-				<&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>;
-			clock-names = "iface", "core";
-			clock-frequency  = <400000>;
-			dmas = <&blsp_dma 17>, <&blsp_dma 16>;
-			dma-names = "rx", "tx";
+			clocks = <&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			clock-frequency = <400000>;
+			dmas = <&blsp_dma 16>, <&blsp_dma 17>;
+			dma-names = "tx", "rx";
 			status = "disabled";
 		};
 
@@ -373,6 +368,8 @@
 
 		intc: interrupt-controller@b000000 {
 			compatible = "qcom,msm-qgic2";
+			#address-cells = <2>;
+			#size-cells = <2>;
 			interrupt-controller;
 			#interrupt-cells = <0x3>;
 			reg =   <0x0 0x0b000000 0x0 0x1000>,  /*GICD*/
@@ -380,6 +377,13 @@
 				<0x0 0x0b001000 0x0 0x1000>,  /*GICH*/
 				<0x0 0x0b004000 0x0 0x1000>;  /*GICV*/
 			interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
+			ranges = <0 0 0 0xb00a000 0 0xffd>;
+
+			v2m@0 {
+				compatible = "arm,gic-v2m-frame";
+				msi-controller;
+				reg = <0x0 0x0 0x0 0xffd>;
+			};
 		};
 
 		pcie_phy: phy@84000 {
@@ -425,6 +429,7 @@
 			linux,pci-domain = <0>;
 			bus-range = <0x00 0xff>;
 			num-lanes = <1>;
+			max-link-speed = <3>;
 			#address-cells = <3>;
 			#size-cells = <2>;
 
@@ -515,60 +520,59 @@
 		};
 
 		timer@b120000 {
-			#address-cells = <2>;
-			#size-cells = <2>;
-			ranges;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0 0 0x10000000>;
 			compatible = "arm,armv7-timer-mem";
 			reg = <0x0 0x0b120000 0x0 0x1000>;
-			clock-frequency = <19200000>;
 
 			frame@b120000 {
 				frame-number = <0>;
 				interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
 					     <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0x0 0x0b121000 0x0 0x1000>,
-				      <0x0 0x0b122000 0x0 0x1000>;
+				reg = <0x0b121000 0x1000>,
+				      <0x0b122000 0x1000>;
 			};
 
 			frame@b123000 {
 				frame-number = <1>;
 				interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0x0 0xb123000 0x0 0x1000>;
+				reg = <0x0b123000 0x1000>;
 				status = "disabled";
 			};
 
 			frame@b124000 {
 				frame-number = <2>;
 				interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0x0 0x0b124000 0x0 0x1000>;
+				reg = <0x0b124000 0x1000>;
 				status = "disabled";
 			};
 
 			frame@b125000 {
 				frame-number = <3>;
 				interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0x0 0x0b125000 0x0 0x1000>;
+				reg = <0x0b125000 0x1000>;
 				status = "disabled";
 			};
 
 			frame@b126000 {
 				frame-number = <4>;
 				interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0x0 0x0b126000 0x0 0x1000>;
+				reg = <0x0b126000 0x1000>;
 				status = "disabled";
 			};
 
 			frame@b127000 {
 				frame-number = <5>;
 				interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0x0 0x0b127000 0x0 0x1000>;
+				reg = <0x0b127000 0x1000>;
 				status = "disabled";
 			};
 
 			frame@b128000 {
 				frame-number = <6>;
 				interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0x0 0x0b128000 0x0 0x1000>;
+				reg = <0x0b128000 0x1000>;
 				status = "disabled";
 			};
 		};
@@ -612,6 +616,7 @@
 
 			glink-edge {
 				interrupts = <GIC_SPI 321 IRQ_TYPE_EDGE_RISING>;
+				label = "rtr";
 				qcom,remote-pid = <1>;
 				mboxes = <&apcs_glb 8>;
 
@@ -621,6 +626,16 @@
 			};
 		};
 
+		mdio: mdio@90000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "qcom,ipq6018-mdio", "qcom,ipq4019-mdio";
+			reg = <0x0 0x90000 0x0 0x64>;
+			clocks = <&gcc GCC_MDIO_AHB_CLK>;
+			clock-names = "gcc_mdio_ahb_clk";
+			status = "disabled";
+		};
+
 		qusb_phy_1: qusb@59000 {
 			compatible = "qcom,ipq6018-qusb2-phy";
 			reg = <0x0 0x059000 0x0 0x180>;
@@ -634,7 +649,7 @@
 			status = "disabled";
 		};
 
-		usb2: usb2@7000000 {
+		usb2: usb@70f8800 {
 			compatible = "qcom,ipq6018-dwc3", "qcom,dwc3";
 			reg = <0x0 0x070F8800 0x0 0x400>;
 			#address-cells = <2>;
@@ -643,7 +658,7 @@
 			clocks = <&gcc GCC_USB1_MASTER_CLK>,
 				 <&gcc GCC_USB1_SLEEP_CLK>,
 				 <&gcc GCC_USB1_MOCK_UTMI_CLK>;
-			clock-names = "master",
+			clock-names = "core",
 				      "sleep",
 				      "mock_utmi";
 
@@ -674,7 +689,6 @@
 			reg = <0x0 0x78000 0x0 0x1C4>;
 			#address-cells = <2>;
 			#size-cells = <2>;
-			#clock-cells = <1>;
 			ranges;
 
 			clocks = <&gcc GCC_USB0_AUX_CLK>,
@@ -686,12 +700,13 @@
 			reset-names = "phy","common";
 			status = "disabled";
 
-			usb0_ssphy: lane@78200 {
+			usb0_ssphy: phy@78200 {
 				reg = <0x0 0x00078200 0x0 0x130>, /* Tx */
 				      <0x0 0x00078400 0x0 0x200>, /* Rx */
 				      <0x0 0x00078800 0x0 0x1F8>, /* PCS */
 				      <0x0 0x00078600 0x0 0x044>; /* PCS misc */
 				#phy-cells = <0>;
+				#clock-cells = <0>;
 				clocks = <&gcc GCC_USB0_PIPE_CLK>;
 				clock-names = "pipe0";
 				clock-output-names = "gcc_usb0_pipe_clk_src";
@@ -711,7 +726,7 @@
 			status = "disabled";
 		};
 
-		usb3: usb3@8A00000 {
+		usb3: usb@8af8800 {
 			compatible = "qcom,ipq6018-dwc3", "qcom,dwc3";
 			reg = <0x0 0x8AF8800 0x0 0x400>;
 			#address-cells = <2>;
@@ -722,8 +737,8 @@
 				<&gcc GCC_USB0_MASTER_CLK>,
 				<&gcc GCC_USB0_SLEEP_CLK>,
 				<&gcc GCC_USB0_MOCK_UTMI_CLK>;
-			clock-names = "sys_noc_axi",
-				"master",
+			clock-names = "cfg_noc",
+				"core",
 				"sleep",
 				"mock_utmi";
 
@@ -737,18 +752,19 @@
 			resets = <&gcc GCC_USB0_BCR>;
 			status = "disabled";
 
-			dwc_0: usb@8A00000 {
+			dwc_0: usb@8a00000 {
 				compatible = "snps,dwc3";
 				reg = <0x0 0x8A00000 0x0 0xcd00>;
 				interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
 				phys = <&qusb_phy_0>, <&usb0_ssphy>;
 				phy-names = "usb2-phy", "usb3-phy";
+				clocks = <&xo>;
+				clock-names = "ref";
 				tx-fifo-resize;
 				snps,is-utmi-l1-suspend;
 				snps,hird-threshold = /bits/ 8 <0x0>;
 				snps,dis_u2_susphy_quirk;
 				snps,dis_u3_susphy_quirk;
-				snps,ref-clock-period-ns = <0x32>;
 				dr_mode = "host";
 			};
 		};
diff --git a/arch/arm64/boot/dts/qcom/ipq8074-hk01.dts b/arch/arm64/boot/dts/qcom/ipq8074-hk01.dts
index b5e1eaa367bf..7143c936de61 100644
--- a/arch/arm64/boot/dts/qcom/ipq8074-hk01.dts
+++ b/arch/arm64/boot/dts/qcom/ipq8074-hk01.dts
@@ -5,11 +5,8 @@
 #include "ipq8074.dtsi"
 
 / {
-	#address-cells = <0x2>;
-	#size-cells = <0x2>;
 	model = "Qualcomm Technologies, Inc. IPQ8074-HK01";
 	compatible = "qcom,ipq8074-hk01", "qcom,ipq8074";
-	interrupt-parent = <&intc>;
 
 	aliases {
 		serial0 = &blsp1_uart5;
@@ -35,7 +32,7 @@
 &blsp1_spi1 {
 	status = "okay";
 
-	m25p80@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "jedec,spi-nor";
@@ -54,12 +51,12 @@
 
 &pcie0 {
 	status = "okay";
-	perst-gpio = <&tlmm 61 0x1>;
+	perst-gpios = <&tlmm 61 0x1>;
 };
 
 &pcie1 {
 	status = "okay";
-	perst-gpio = <&tlmm 58 0x1>;
+	perst-gpios = <&tlmm 58 0x1>;
 };
 
 &pcie_phy0 {
diff --git a/arch/arm64/boot/dts/qcom/ipq8074-hk10.dtsi b/arch/arm64/boot/dts/qcom/ipq8074-hk10.dtsi
index 07e670829676..db4b87944cdf 100644
--- a/arch/arm64/boot/dts/qcom/ipq8074-hk10.dtsi
+++ b/arch/arm64/boot/dts/qcom/ipq8074-hk10.dtsi
@@ -7,11 +7,6 @@
 #include "ipq8074.dtsi"
 
 / {
-	#address-cells = <0x2>;
-	#size-cells = <0x2>;
-
-	interrupt-parent = <&intc>;
-
 	aliases {
 		serial0 = &blsp1_uart5;
 	};
@@ -29,7 +24,7 @@
 &blsp1_spi1 {
 	status = "ok";
 
-	m25p80@0 {
+	flash@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
 		compatible = "jedec,spi-nor";
@@ -44,12 +39,12 @@
 
 &pcie0 {
 	status = "ok";
-	perst-gpio = <&tlmm 58 0x1>;
+	perst-gpios = <&tlmm 58 0x1>;
 };
 
 &pcie1 {
 	status = "ok";
-	perst-gpio = <&tlmm 61 0x1>;
+	perst-gpios = <&tlmm 61 0x1>;
 };
 
 &pcie_phy0 {
diff --git a/arch/arm64/boot/dts/qcom/ipq8074.dtsi b/arch/arm64/boot/dts/qcom/ipq8074.dtsi
index 6c6a0f853669..a47acf9bdf24 100644
--- a/arch/arm64/boot/dts/qcom/ipq8074.dtsi
+++ b/arch/arm64/boot/dts/qcom/ipq8074.dtsi
@@ -7,13 +7,17 @@
 #include <dt-bindings/clock/qcom,gcc-ipq8074.h>
 
 / {
+	#address-cells = <2>;
+	#size-cells = <2>;
+
 	model = "Qualcomm Technologies, Inc. IPQ8074";
 	compatible = "qcom,ipq8074";
+	interrupt-parent = <&intc>;
 
 	clocks {
 		sleep_clk: sleep_clk {
 			compatible = "fixed-clock";
-			clock-frequency = <32000>;
+			clock-frequency = <32768>;
 			#clock-cells = <0>;
 		};
 
@@ -76,6 +80,25 @@
 		method = "smc";
 	};
 
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		smem@4ab00000 {
+			compatible = "qcom,smem";
+			reg = <0x0 0x4ab00000 0x0 0x00100000>;
+			no-map;
+
+			hwlocks = <&tcsr_mutex 0>;
+		};
+
+		memory@4ac00000 {
+			no-map;
+			reg = <0x0 0x4ac00000 0x0 0x00400000>;
+		};
+	};
+
 	firmware {
 		scm {
 			compatible = "qcom,scm-ipq8074", "qcom,scm";
@@ -100,7 +123,7 @@
 				<&xo>;
 			clock-names = "aux", "cfg_ahb", "ref";
 
-			resets =  <&gcc GCC_USB1_PHY_BCR>,
+			resets = <&gcc GCC_USB1_PHY_BCR>,
 				<&gcc GCC_USB3PHY_1_PHY_BCR>;
 			reset-names = "phy","common";
 			status = "disabled";
@@ -111,7 +134,7 @@
 				      <0x00058800 0x1f8>,     /* PCS  */
 				      <0x00058600 0x044>;     /* PCS misc*/
 				#phy-cells = <0>;
-				#clock-cells = <1>;
+				#clock-cells = <0>;
 				clocks = <&gcc GCC_USB1_PIPE_CLK>;
 				clock-names = "pipe0";
 				clock-output-names = "gcc_usb1_pipe_clk_src";
@@ -143,7 +166,7 @@
 				<&xo>;
 			clock-names = "aux", "cfg_ahb", "ref";
 
-			resets =  <&gcc GCC_USB0_PHY_BCR>,
+			resets = <&gcc GCC_USB0_PHY_BCR>,
 				<&gcc GCC_USB3PHY_0_PHY_BCR>;
 			reset-names = "phy","common";
 			status = "disabled";
@@ -154,7 +177,7 @@
 				      <0x00078800 0x1f8>,     /* PCS  */
 				      <0x00078600 0x044>;     /* PCS misc*/
 				#phy-cells = <0>;
-				#clock-cells = <1>;
+				#clock-cells = <0>;
 				clocks = <&gcc GCC_USB0_PIPE_CLK>;
 				clock-names = "pipe0";
 				clock-output-names = "gcc_usb0_pipe_clk_src";
@@ -176,7 +199,7 @@
 
 		pcie_qmp0: phy@86000 {
 			compatible = "qcom,ipq8074-qmp-pcie-phy";
-			reg = <0x00086000 0x1000>;
+			reg = <0x00086000 0x1c4>;
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges;
@@ -204,7 +227,7 @@
 
 		pcie_qmp1: phy@8e000 {
 			compatible = "qcom,ipq8074-qmp-pcie-phy";
-			reg = <0x0008e000 0x1000>;
+			reg = <0x0008e000 0x1c4>;
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges;
@@ -230,6 +253,18 @@
 			};
 		};
 
+		mdio: mdio@90000 {
+			compatible = "qcom,ipq4019-mdio";
+			reg = <0x00090000 0x64>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			clocks = <&gcc GCC_MDIO_AHB_CLK>;
+			clock-names = "gcc_mdio_ahb_clk";
+
+			status = "disabled";
+		};
+
 		prng: rng@e3000 {
 			compatible = "qcom,prng-ee";
 			reg = <0x000e3000 0x1000>;
@@ -316,9 +351,16 @@
 			compatible = "qcom,gcc-ipq8074";
 			reg = <0x01800000 0x80000>;
 			#clock-cells = <0x1>;
+			#power-domain-cells = <1>;
 			#reset-cells = <0x1>;
 		};
 
+		tcsr_mutex: hwlock@1905000 {
+			compatible = "qcom,tcsr-mutex";
+			reg = <0x01905000 0x20000>;
+			#hwlock-cells = <1>;
+		};
+
 		spmi_bus: spmi@200f000 {
 			compatible = "qcom,spmi-pmic-arb";
 			reg = <0x0200f000 0x001000>,
@@ -338,19 +380,20 @@
 			cell-index = <0>;
 		};
 
-		sdhc_1: sdhci@7824900 {
+		sdhc_1: mmc@7824900 {
 			compatible = "qcom,sdhci-msm-v4";
 			reg = <0x7824900 0x500>, <0x7824000 0x800>;
-			reg-names = "hc_mem", "core_mem";
+			reg-names = "hc", "core";
 
 			interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "hc_irq", "pwr_irq";
 
-			clocks = <&xo>,
-				 <&gcc GCC_SDCC1_AHB_CLK>,
-				 <&gcc GCC_SDCC1_APPS_CLK>;
-			clock-names = "xo", "iface", "core";
+			clocks = <&gcc GCC_SDCC1_AHB_CLK>,
+				 <&gcc GCC_SDCC1_APPS_CLK>,
+				 <&xo>;
+			clock-names = "iface", "core", "xo";
+			resets = <&gcc GCC_SDCC1_BCR>;
 			max-frequency = <384000000>;
 			mmc-ddr-1_8v;
 			mmc-hs200-1_8v;
@@ -430,12 +473,12 @@
 			#size-cells = <0>;
 			reg = <0x078b6000 0x600>;
 			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc GCC_BLSP1_AHB_CLK>,
-				<&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>;
-			clock-names = "iface", "core";
+			clocks = <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
 			clock-frequency = <400000>;
-			dmas = <&blsp_dma 15>, <&blsp_dma 14>;
-			dma-names = "rx", "tx";
+			dmas = <&blsp_dma 14>, <&blsp_dma 15>;
+			dma-names = "tx", "rx";
 			pinctrl-0 = <&i2c_0_pins>;
 			pinctrl-names = "default";
 			status = "disabled";
@@ -447,12 +490,12 @@
 			#size-cells = <0>;
 			reg = <0x078b7000 0x600>;
 			interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc GCC_BLSP1_AHB_CLK>,
-				<&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>;
-			clock-names = "iface", "core";
+			clocks = <&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
 			clock-frequency = <100000>;
-			dmas = <&blsp_dma 17>, <&blsp_dma 16>;
-			dma-names = "rx", "tx";
+			dmas = <&blsp_dma 16>, <&blsp_dma 17>;
+			dma-names = "tx", "rx";
 			status = "disabled";
 		};
 
@@ -462,12 +505,12 @@
 			#size-cells = <0>;
 			reg = <0x78b9000 0x600>;
 			interrupts = <GIC_SPI 299 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc GCC_BLSP1_AHB_CLK>,
-				 <&gcc GCC_BLSP1_QUP5_I2C_APPS_CLK>;
-			clock-names = "iface", "core";
+			clocks = <&gcc GCC_BLSP1_QUP5_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
 			clock-frequency = <400000>;
-			dmas = <&blsp_dma 21>, <&blsp_dma 20>;
-			dma-names = "rx", "tx";
+			dmas = <&blsp_dma 20>, <&blsp_dma 21>;
+			dma-names = "tx", "rx";
 			status = "disabled";
 		};
 
@@ -477,12 +520,12 @@
 			#size-cells = <0>;
 			reg = <0x078ba000 0x600>;
 			interrupts = <GIC_SPI 300 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc GCC_BLSP1_AHB_CLK>,
-				 <&gcc GCC_BLSP1_QUP6_I2C_APPS_CLK>;
-			clock-names = "iface", "core";
+			clocks = <&gcc GCC_BLSP1_QUP6_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
 			clock-frequency = <100000>;
-			dmas = <&blsp_dma 23>, <&blsp_dma 22>;
-			dma-names = "rx", "tx";
+			dmas = <&blsp_dma 22>, <&blsp_dma 23>;
+			dma-names = "tx", "rx";
 			status = "disabled";
 		};
 
@@ -497,7 +540,7 @@
 			status = "disabled";
 		};
 
-		qpic_nand: nand@79b0000 {
+		qpic_nand: nand-controller@79b0000 {
 			compatible = "qcom,ipq8074-nand";
 			reg = <0x079b0000 0x10000>;
 			#address-cells = <1>;
@@ -516,7 +559,7 @@
 		};
 
 		usb_0: usb@8af8800 {
-			compatible = "qcom,dwc3";
+			compatible = "qcom,ipq8074-dwc3", "qcom,dwc3";
 			reg = <0x08af8800 0x400>;
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -526,8 +569,8 @@
 				<&gcc GCC_USB0_MASTER_CLK>,
 				<&gcc GCC_USB0_SLEEP_CLK>,
 				<&gcc GCC_USB0_MOCK_UTMI_CLK>;
-			clock-names = "sys_noc_axi",
-				"master",
+			clock-names = "cfg_noc",
+				"core",
 				"sleep",
 				"mock_utmi";
 
@@ -538,10 +581,12 @@
 						<133330000>,
 						<19200000>;
 
+			power-domains = <&gcc USB0_GDSC>;
+
 			resets = <&gcc GCC_USB0_BCR>;
 			status = "disabled";
 
-			dwc_0: dwc3@8a00000 {
+			dwc_0: usb@8a00000 {
 				compatible = "snps,dwc3";
 				reg = <0x8a00000 0xcd00>;
 				interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
@@ -556,7 +601,7 @@
 		};
 
 		usb_1: usb@8cf8800 {
-			compatible = "qcom,dwc3";
+			compatible = "qcom,ipq8074-dwc3", "qcom,dwc3";
 			reg = <0x08cf8800 0x400>;
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -566,8 +611,8 @@
 				<&gcc GCC_USB1_MASTER_CLK>,
 				<&gcc GCC_USB1_SLEEP_CLK>,
 				<&gcc GCC_USB1_MOCK_UTMI_CLK>;
-			clock-names = "sys_noc_axi",
-				"master",
+			clock-names = "cfg_noc",
+				"core",
 				"sleep",
 				"mock_utmi";
 
@@ -578,10 +623,12 @@
 						<133330000>,
 						<19200000>;
 
+			power-domains = <&gcc USB1_GDSC>;
+
 			resets = <&gcc GCC_USB1_BCR>;
 			status = "disabled";
 
-			dwc_1: dwc3@8c00000 {
+			dwc_1: usb@8c00000 {
 				compatible = "snps,dwc3";
 				reg = <0x8c00000 0xcd00>;
 				interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>;
@@ -597,17 +644,18 @@
 
 		intc: interrupt-controller@b000000 {
 			compatible = "qcom,msm-qgic2";
+			#address-cells = <1>;
+			#size-cells = <1>;
 			interrupt-controller;
 			#interrupt-cells = <0x3>;
 			reg = <0x0b000000 0x1000>, <0x0b002000 0x1000>;
-		};
+			ranges = <0 0xb00a000 0xffd>;
 
-		timer {
-			compatible = "arm,armv8-timer";
-			interrupts = <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
-				     <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
-				     <GIC_PPI 4 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
-				     <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+			v2m@0 {
+				compatible = "arm,gic-v2m-frame";
+				msi-controller;
+				reg = <0x0 0xffd>;
+			};
 		};
 
 		watchdog: watchdog@b017000 {
@@ -618,13 +666,20 @@
 			timeout-sec = <30>;
 		};
 
+		apcs_glb: mailbox@b111000 {
+			compatible = "qcom,ipq8074-apcs-apps-global";
+			reg = <0x0b111000 0x6000>;
+
+			#clock-cells = <1>;
+			#mbox-cells = <1>;
+		};
+
 		timer@b120000 {
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges;
 			compatible = "arm,armv7-timer-mem";
 			reg = <0x0b120000 0x1000>;
-			clock-frequency = <19200000>;
 
 			frame@b120000 {
 				frame-number = <0>;
@@ -802,4 +857,12 @@
 			status = "disabled";
 		};
 	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupts = <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 4 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+	};
 };
diff --git a/arch/arm64/boot/dts/qcom/msm8916-alcatel-idol347.dts b/arch/arm64/boot/dts/qcom/msm8916-alcatel-idol347.dts
index 265e539e7e99..3dc9619fde6e 100644
--- a/arch/arm64/boot/dts/qcom/msm8916-alcatel-idol347.dts
+++ b/arch/arm64/boot/dts/qcom/msm8916-alcatel-idol347.dts
@@ -27,7 +27,7 @@
 
 		label = "GPIO Buttons";
 
-		volume-up {
+		button-volume-up {
 			label = "Volume Up";
 			gpios = <&msmgpio 107 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_VOLUMEUP>;
diff --git a/arch/arm64/boot/dts/qcom/msm8916-asus-z00l.dts b/arch/arm64/boot/dts/qcom/msm8916-asus-z00l.dts
index d4d33dd3584a..dd92070a1211 100644
--- a/arch/arm64/boot/dts/qcom/msm8916-asus-z00l.dts
+++ b/arch/arm64/boot/dts/qcom/msm8916-asus-z00l.dts
@@ -28,14 +28,14 @@
 
 		label = "GPIO Buttons";
 
-		volume-up {
+		button-volume-up {
 			label = "Volume Up";
 			gpios = <&msmgpio 107 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_VOLUMEUP>;
 			debounce-interval = <15>;
 		};
 
-		volume-down {
+		button-volume-down {
 			label = "Volume Down";
 			gpios = <&msmgpio 117 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_VOLUMEDOWN>;
diff --git a/arch/arm64/boot/dts/qcom/msm8916-huawei-g7.dts b/arch/arm64/boot/dts/qcom/msm8916-huawei-g7.dts
index 42d93d3fba36..9e470c67274e 100644
--- a/arch/arm64/boot/dts/qcom/msm8916-huawei-g7.dts
+++ b/arch/arm64/boot/dts/qcom/msm8916-huawei-g7.dts
@@ -8,18 +8,14 @@
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/leds/common.h>
+#include <dt-bindings/sound/apq8016-lpass.h>
 
 /*
  * Note: The original firmware from Huawei can only boot 32-bit kernels.
- * To boot arm64 kernels it is necessary to flash 64-bit TZ/HYP firmware
- * with EDL, e.g. taken from the DragonBoard 410c. This works because Huawei
- * forgot to set up (firmware) secure boot for some reason.
- *
- * Also note that Huawei no longer provides bootloader unlock codes.
- * This can be bypassed by patching the bootloader from a custom HYP firmware,
- * making it think the bootloader is unlocked.
- *
- * See: https://wiki.postmarketos.org/wiki/Huawei_Ascend_G7_(huawei-g7)
+ * To boot this device tree using arm64 it is necessary to flash 64-bit TZ/HYP
+ * firmware (e.g. taken from the DragonBoard 410c).
+ * See https://wiki.postmarketos.org/wiki/Huawei_Ascend_G7_(huawei-g7)
+ * for suggested installation instructions.
  */
 
 / {
@@ -43,7 +39,7 @@
 
 		label = "GPIO Buttons";
 
-		volume-up {
+		button-volume-up {
 			label = "Volume Up";
 			gpios = <&msmgpio 107 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_VOLUMEUP>;
@@ -216,6 +212,10 @@
 	status = "okay";
 };
 
+&lpass {
+	status = "okay";
+};
+
 &pm8916_resin {
 	status = "okay";
 	linux,code = <KEY_VOLUMEDOWN>;
@@ -260,6 +260,40 @@
 	cd-gpios = <&msmgpio 56 GPIO_ACTIVE_LOW>;
 };
 
+&sound {
+	status = "okay";
+
+	model = "msm8916";
+	audio-routing =
+		"AMIC1", "MIC BIAS External1",
+		"AMIC2", "MIC BIAS External2",
+		"AMIC3", "MIC BIAS External1";
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&cdc_pdm_lines_act>;
+	pinctrl-1 = <&cdc_pdm_lines_sus>;
+
+	primary-dai-link {
+		link-name = "WCD";
+		cpu {
+			sound-dai = <&lpass MI2S_PRIMARY>;
+		};
+		codec {
+			sound-dai = <&lpass_codec 0>, <&wcd_codec 0>;
+		};
+	};
+
+	tertiary-dai-link {
+		link-name = "WCD-Capture";
+		cpu {
+			sound-dai = <&lpass MI2S_TERTIARY>;
+		};
+		codec {
+			sound-dai = <&lpass_codec 1>, <&wcd_codec 1>;
+		};
+	};
+};
+
 &usb {
 	status = "okay";
 	extcon = <&usb_id>, <&usb_id>;
@@ -269,6 +303,13 @@
 	extcon = <&usb_id>;
 };
 
+&wcd_codec {
+	qcom,micbias-lvl = <2800>;
+	qcom,mbhc-vthreshold-low = <75 150 237 450 500>;
+	qcom,mbhc-vthreshold-high = <75 150 237 450 500>;
+	qcom,hphl-jack-type-normally-open;
+};
+
 &smd_rpm_regulators {
 	vdd_l1_l2_l3-supply = <&pm8916_s3>;
 	vdd_l4_l5_l6-supply = <&pm8916_s4>;
diff --git a/arch/arm64/boot/dts/qcom/msm8916-longcheer-l8150.dts b/arch/arm64/boot/dts/qcom/msm8916-longcheer-l8150.dts
index 852de624f5af..d85e7f7c0835 100644
--- a/arch/arm64/boot/dts/qcom/msm8916-longcheer-l8150.dts
+++ b/arch/arm64/boot/dts/qcom/msm8916-longcheer-l8150.dts
@@ -39,7 +39,7 @@
 
 		label = "GPIO Buttons";
 
-		volume-up {
+		button-volume-up {
 			label = "Volume Up";
 			gpios = <&msmgpio 107 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_VOLUMEUP>;
@@ -151,6 +151,21 @@
 		vddio-supply = <&pm8916_l6>;
 	};
 
+	light-sensor@23 {
+		compatible = "liteon,ltr559";
+		reg = <0x23>;
+		proximity-near-level = <75>;
+
+		interrupt-parent = <&msmgpio>;
+		interrupts = <115 IRQ_TYPE_EDGE_FALLING>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&light_int_default>;
+
+		vdd-supply = <&pm8916_l17>;
+		vio-supply = <&pm8916_l6>;
+	};
+
 	gyroscope@68 {
 		compatible = "bosch,bmg160";
 		reg = <0x68>;
@@ -392,6 +407,14 @@
 		bias-disable;
 	};
 
+	light_int_default: light-int-default {
+		pins = "gpio115";
+		function = "gpio";
+
+		drive-strength = <2>;
+		bias-disable;
+	};
+
 	magn_int_default: magn-int-default {
 		pins = "gpio113";
 		function = "gpio";
diff --git a/arch/arm64/boot/dts/qcom/msm8916-longcheer-l8910.dts b/arch/arm64/boot/dts/qcom/msm8916-longcheer-l8910.dts
index f9ce123471d4..b4812f093b17 100644
--- a/arch/arm64/boot/dts/qcom/msm8916-longcheer-l8910.dts
+++ b/arch/arm64/boot/dts/qcom/msm8916-longcheer-l8910.dts
@@ -28,7 +28,7 @@
 
 		label = "GPIO Buttons";
 
-		volume-up {
+		button-volume-up {
 			label = "Volume Up";
 			gpios = <&msmgpio 107 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_VOLUMEUP>;
diff --git a/arch/arm64/boot/dts/qcom/msm8916-samsung-a2015-common.dtsi b/arch/arm64/boot/dts/qcom/msm8916-samsung-a2015-common.dtsi
index 9b4b7de7cec2..3255bd3fcb55 100644
--- a/arch/arm64/boot/dts/qcom/msm8916-samsung-a2015-common.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8916-samsung-a2015-common.dtsi
@@ -31,13 +31,13 @@
 
 		label = "GPIO Buttons";
 
-		volume-up {
+		button-volume-up {
 			label = "Volume Up";
 			gpios = <&msmgpio 107 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_VOLUMEUP>;
 		};
 
-		home {
+		button-home {
 			label = "Home";
 			gpios = <&msmgpio 109 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_HOMEPAGE>;
@@ -52,7 +52,7 @@
 
 		label = "GPIO Hall Effect Sensor";
 
-		hall-sensor {
+		event-hall-sensor {
 			label = "Hall Effect Sensor";
 			gpios = <&msmgpio 52 GPIO_ACTIVE_LOW>;
 			linux,input-type = <EV_SW>;
@@ -61,9 +61,9 @@
 		};
 	};
 
-	reg_vdd_tsp: regulator-vdd-tsp {
+	reg_vdd_tsp_a: regulator-vdd-tsp-a {
 		compatible = "regulator-fixed";
-		regulator-name = "vdd_tsp";
+		regulator-name = "vdd_tsp_a";
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
 
@@ -460,10 +460,18 @@
 		drive-strength = <2>;
 		bias-disable;
 	};
+
+	ts_int_default: ts-int-default {
+		pins = "gpio13";
+		function = "gpio";
+
+		drive-strength = <2>;
+		bias-disable;
+	};
 };
 
 &pm8916_gpios {
-	nfc_clk_req: nfc-clk-req {
+	nfc_clk_req: nfc-clk-req-state {
 		pins = "gpio2";
 		function = "func1";
 
diff --git a/arch/arm64/boot/dts/qcom/msm8916-samsung-a3u-eur.dts b/arch/arm64/boot/dts/qcom/msm8916-samsung-a3u-eur.dts
index 4ba11b020f9b..6db5f78ca286 100644
--- a/arch/arm64/boot/dts/qcom/msm8916-samsung-a3u-eur.dts
+++ b/arch/arm64/boot/dts/qcom/msm8916-samsung-a3u-eur.dts
@@ -73,8 +73,8 @@
 		touchscreen-size-x = <540>;
 		touchscreen-size-y = <960>;
 
-		vdd-supply = <&reg_vdd_tsp>;
-		vddo-supply = <&pm8916_l6>;
+		vcca-supply = <&reg_vdd_tsp_a>;
+		vdd-supply = <&pm8916_l6>;
 
 		pinctrl-names = "default";
 		pinctrl-0 = <&ts_int_default>;
@@ -128,12 +128,4 @@
 		drive-strength = <2>;
 		bias-disable;
 	};
-
-	ts_int_default: ts-int-default {
-		pins = "gpio13";
-		function = "gpio";
-
-		drive-strength = <2>;
-		bias-disable;
-	};
 };
diff --git a/arch/arm64/boot/dts/qcom/msm8916-samsung-a5u-eur.dts b/arch/arm64/boot/dts/qcom/msm8916-samsung-a5u-eur.dts
index d978c9ac179d..5fb8ecd0c9ca 100644
--- a/arch/arm64/boot/dts/qcom/msm8916-samsung-a5u-eur.dts
+++ b/arch/arm64/boot/dts/qcom/msm8916-samsung-a5u-eur.dts
@@ -42,7 +42,7 @@
 		touchscreen-size-x = <720>;
 		touchscreen-size-y = <1280>;
 
-		avdd-supply = <&reg_vdd_tsp>;
+		avdd-supply = <&reg_vdd_tsp_a>;
 		vdd-supply = <&pm8916_l6>;
 
 		pinctrl-names = "default";
@@ -69,12 +69,4 @@
 		drive-strength = <2>;
 		bias-disable;
 	};
-
-	ts_int_default: ts-int-default {
-		pins = "gpio13";
-		function = "gpio";
-
-		drive-strength = <2>;
-		bias-disable;
-	};
 };
diff --git a/arch/arm64/boot/dts/qcom/msm8916-samsung-e2015-common.dtsi b/arch/arm64/boot/dts/qcom/msm8916-samsung-e2015-common.dtsi
new file mode 100644
index 000000000000..542010fdfb8a
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/msm8916-samsung-e2015-common.dtsi
@@ -0,0 +1,85 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+#include "msm8916-samsung-a2015-common.dtsi"
+
+/ {
+	haptic {
+		compatible = "regulator-haptic";
+		haptic-supply = <&reg_motor_vdd>;
+		min-microvolt = <3300000>;
+		max-microvolt = <3300000>;
+	};
+
+	i2c-muic {
+		/* SM5504 MUIC instead of SM5502 */
+		/delete-node/ extcon@25;
+
+		muic: extcon@14 {
+			compatible = "siliconmitus,sm5504-muic";
+			reg = <0x14>;
+
+			interrupt-parent = <&msmgpio>;
+			interrupts = <12 IRQ_TYPE_EDGE_FALLING>;
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&muic_int_default>;
+		};
+	};
+
+	reg_motor_vdd: regulator-motor-vdd {
+		compatible = "regulator-fixed";
+		regulator-name = "motor_vdd";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&msmgpio 76 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&motor_en_default>;
+	};
+
+	reg_touch_key: regulator-touch-key {
+		compatible = "regulator-fixed";
+		regulator-name = "touch_key";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&msmgpio 97 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&tkey_en_default>;
+	};
+};
+
+&blsp_i2c2 {
+	/* lis2hh12 accelerometer instead of BMC150 */
+	status = "disabled";
+
+	/delete-node/ accelerometer@10;
+	/delete-node/ magnetometer@12;
+};
+
+&touchkey {
+	vcc-supply = <&reg_touch_key>;
+	vdd-supply = <&reg_touch_key>;
+};
+
+&msmgpio {
+	motor_en_default: motor-en-default {
+		pins = "gpio76";
+		function = "gpio";
+
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	tkey_en_default: tkey-en-default {
+		pins = "gpio97";
+		function = "gpio";
+
+		drive-strength = <2>;
+		bias-disable;
+	};
+};
diff --git a/arch/arm64/boot/dts/qcom/msm8916-samsung-e5.dts b/arch/arm64/boot/dts/qcom/msm8916-samsung-e5.dts
new file mode 100644
index 000000000000..777eb934eb4b
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/msm8916-samsung-e5.dts
@@ -0,0 +1,24 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+/dts-v1/;
+
+#include "msm8916-samsung-e2015-common.dtsi"
+
+/*
+ * NOTE: The original firmware from Samsung can only boot ARM32 kernels on some
+ * variants.
+ * Unfortunately, the firmware is signed and cannot be replaced easily.
+ * There seems to be no way to boot ARM64 kernels on 32-bit devices at the
+ * moment, even though the hardware would support it.
+ *
+ * However, it is possible to use this device tree by compiling an ARM32 kernel
+ * instead. For clarity and build testing this device tree is maintained next
+ * to the other MSM8916 device trees. However, it is actually used through
+ * arch/arm/boot/dts/qcom-msm8916-samsung-e5.dts
+ */
+
+/ {
+	model = "Samsung Galaxy E5";
+	compatible = "samsung,e5", "qcom,msm8916";
+	chassis-type = "handset";
+};
diff --git a/arch/arm64/boot/dts/qcom/msm8916-samsung-e7.dts b/arch/arm64/boot/dts/qcom/msm8916-samsung-e7.dts
new file mode 100644
index 000000000000..b412b61ca258
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/msm8916-samsung-e7.dts
@@ -0,0 +1,29 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+/dts-v1/;
+
+#include "msm8916-samsung-e2015-common.dtsi"
+
+/*
+ * NOTE: The original firmware from Samsung can only boot ARM32 kernels on some
+ * variants.
+ * Unfortunately, the firmware is signed and cannot be replaced easily.
+ * There seems to be no way to boot ARM64 kernels on 32-bit devices at the
+ * moment, even though the hardware would support it.
+ *
+ * However, it is possible to use this device tree by compiling an ARM32 kernel
+ * instead. For clarity and build testing this device tree is maintained next
+ * to the other MSM8916 device trees. However, it is actually used through
+ * arch/arm/boot/dts/qcom-msm8916-samsung-e7.dts
+ */
+
+/ {
+	model = "Samsung Galaxy E7";
+	compatible = "samsung,e7", "qcom,msm8916";
+	chassis-type = "handset";
+};
+
+&pm8916_l17 {
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+};
diff --git a/arch/arm64/boot/dts/qcom/msm8916-samsung-grandmax.dts b/arch/arm64/boot/dts/qcom/msm8916-samsung-grandmax.dts
new file mode 100644
index 000000000000..bc7134698978
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/msm8916-samsung-grandmax.dts
@@ -0,0 +1,60 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+/dts-v1/;
+
+#include "msm8916-samsung-e2015-common.dtsi"
+#include <dt-bindings/leds/common.h>
+
+/*
+ * NOTE: The original firmware from Samsung can only boot ARM32 kernels on some
+ * variants.
+ * Unfortunately, the firmware is signed and cannot be replaced easily.
+ * There seems to be no way to boot ARM64 kernels on 32-bit devices at the
+ * moment, even though the hardware would support it.
+ *
+ * However, it is possible to use this device tree by compiling an ARM32 kernel
+ * instead. For clarity and build testing this device tree is maintained next
+ * to the other MSM8916 device trees. However, it is actually used through
+ * arch/arm/boot/dts/qcom-msm8916-samsung-grandmax.dts
+ */
+
+/ {
+	model = "Samsung Galaxy Grand Max";
+	compatible = "samsung,grandmax", "qcom,msm8916";
+	chassis-type = "handset";
+
+	/delete-node/ gpio-hall-sensor;
+	/delete-node/ i2c-nfc;
+	/delete-node/ i2c-tkey;
+
+	gpio-leds {
+		compatible = "gpio-leds";
+		keyled {
+			gpios = <&msmgpio 60 GPIO_ACTIVE_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&gpio_leds_default>;
+		};
+	};
+};
+
+&reg_motor_vdd {
+	gpio = <&msmgpio 72 GPIO_ACTIVE_HIGH>;
+};
+
+&reg_touch_key {
+	status = "disabled";
+};
+
+&msmgpio {
+	gpio_leds_default: gpio-led-default {
+		pins = "gpio60";
+		function = "gpio";
+
+		drive-strength = <2>;
+		bias-disable;
+	};
+};
+
+&motor_en_default {
+	pins = "gpio72";
+};
diff --git a/arch/arm64/boot/dts/qcom/msm8916-samsung-j5.dts b/arch/arm64/boot/dts/qcom/msm8916-samsung-j5.dts
new file mode 100644
index 000000000000..eabeed18cfaa
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/msm8916-samsung-j5.dts
@@ -0,0 +1,209 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+/dts-v1/;
+
+#include "msm8916-pm8916.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "Samsung Galaxy J5 (2015)";
+	compatible = "samsung,j5", "qcom,msm8916";
+	chassis-type = "handset";
+
+	aliases {
+		serial0 = &blsp1_uart2;
+	};
+
+	chosen {
+		stdout-path = "serial0";
+	};
+
+	reserved-memory {
+		/* Additional memory used by Samsung firmware modifications */
+		tz-apps@85500000 {
+			reg = <0x0 0x85500000 0x0 0xb00000>;
+			no-map;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_keys_default>;
+
+		label = "GPIO Buttons";
+
+		button-volume-up {
+			label = "Volume Up";
+			gpios = <&msmgpio 107 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+		};
+
+		button-home {
+			label = "Home Key";
+			gpios = <&msmgpio 109 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_HOMEPAGE>;
+		};
+	};
+};
+
+&blsp1_uart2 {
+	status = "okay";
+};
+
+&pm8916_resin {
+	status = "okay";
+	linux,code = <KEY_VOLUMEDOWN>;
+};
+
+/* FIXME: Replace with SM5703 MUIC when driver is available */
+&pm8916_usbin {
+	status = "okay";
+};
+
+&pronto {
+	status = "okay";
+};
+
+&sdhc_1 {
+	status = "okay";
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on>;
+	pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off>;
+};
+
+&sdhc_2 {
+	status = "okay";
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on &sdc2_cd_on>;
+	pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdc2_cd_off>;
+
+	cd-gpios = <&msmgpio 38 GPIO_ACTIVE_LOW>;
+};
+
+&usb {
+	status = "okay";
+	dr_mode = "peripheral";
+	extcon = <&pm8916_usbin>;
+};
+
+&usb_hs_phy {
+	extcon = <&pm8916_usbin>;
+	qcom,init-seq = /bits/ 8 <0x1 0x19 0x2 0x0b>;
+};
+
+&smd_rpm_regulators {
+	vdd_l1_l2_l3-supply = <&pm8916_s3>;
+	vdd_l4_l5_l6-supply = <&pm8916_s4>;
+	vdd_l7-supply = <&pm8916_s4>;
+
+	s3 {
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <1300000>;
+	};
+
+	s4 {
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <2100000>;
+	};
+
+	l1 {
+		regulator-min-microvolt = <1225000>;
+		regulator-max-microvolt = <1225000>;
+	};
+
+	l2 {
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <1200000>;
+	};
+
+	l4 {
+		regulator-min-microvolt = <2050000>;
+		regulator-max-microvolt = <2050000>;
+	};
+
+	l5 {
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	l6 {
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	l7 {
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	l8 {
+		regulator-min-microvolt = <2850000>;
+		regulator-max-microvolt = <2900000>;
+	};
+
+	l9 {
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	l10 {
+		regulator-min-microvolt = <2700000>;
+		regulator-max-microvolt = <2800000>;
+	};
+
+	l11 {
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <2950000>;
+		regulator-allow-set-load;
+		regulator-system-load = <200000>;
+	};
+
+	l12 {
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <2950000>;
+	};
+
+	l13 {
+		regulator-min-microvolt = <3075000>;
+		regulator-max-microvolt = <3075000>;
+	};
+
+	l14 {
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	l15 {
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	l16 {
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	l17 {
+		regulator-min-microvolt = <3000000>;
+		regulator-max-microvolt = <3000000>;
+	};
+
+	l18 {
+		regulator-min-microvolt = <2700000>;
+		regulator-max-microvolt = <2700000>;
+	};
+};
+
+&msmgpio {
+	gpio_keys_default: gpio-keys-default {
+		pins = "gpio107", "gpio109";
+		function = "gpio";
+
+		drive-strength = <2>;
+		bias-pull-up;
+	};
+};
diff --git a/arch/arm64/boot/dts/qcom/msm8916-samsung-serranove.dts b/arch/arm64/boot/dts/qcom/msm8916-samsung-serranove.dts
index a78f87a5bf4f..bbd6bb3f4fd7 100644
--- a/arch/arm64/boot/dts/qcom/msm8916-samsung-serranove.dts
+++ b/arch/arm64/boot/dts/qcom/msm8916-samsung-serranove.dts
@@ -23,6 +23,7 @@
 / {
 	model = "Samsung Galaxy S4 Mini Value Edition";
 	compatible = "samsung,serranove", "qcom,msm8916";
+	chassis-type = "handset";
 
 	aliases {
 		serial0 = &blsp1_uart2;
@@ -48,13 +49,13 @@
 
 		label = "GPIO Buttons";
 
-		volume-up {
+		button-volume-up {
 			label = "Volume Up";
 			gpios = <&msmgpio 107 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_VOLUMEUP>;
 		};
 
-		home {
+		button-home {
 			label = "Home";
 			gpios = <&msmgpio 109 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_HOMEPAGE>;
@@ -69,7 +70,7 @@
 
 		label = "GPIO Hall Effect Sensor";
 
-		hall-sensor {
+		event-hall-sensor {
 			label = "Hall Effect Sensor";
 			gpios = <&msmgpio 52 GPIO_ACTIVE_LOW>;
 			linux,input-type = <EV_SW>;
@@ -209,6 +210,15 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&imu_irq_default>;
 	};
+
+	magnetometer@2e {
+		compatible = "yamaha,yas537";
+		reg = <0x2e>;
+
+		mount-matrix =  "0",  "1",  "0",
+				"1",  "0",  "0",
+				"0",  "0", "-1";
+	};
 };
 
 &blsp_i2c4 {
diff --git a/arch/arm64/boot/dts/qcom/msm8916-wingtech-wt88047.dts b/arch/arm64/boot/dts/qcom/msm8916-wingtech-wt88047.dts
index 69a44c6f57fc..84a352dcf9a2 100644
--- a/arch/arm64/boot/dts/qcom/msm8916-wingtech-wt88047.dts
+++ b/arch/arm64/boot/dts/qcom/msm8916-wingtech-wt88047.dts
@@ -29,7 +29,7 @@
 
 		label = "GPIO Buttons";
 
-		volume-up {
+		button-volume-up {
 			label = "Volume Up";
 			gpios = <&msmgpio 107 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_VOLUMEUP>;
diff --git a/arch/arm64/boot/dts/qcom/msm8916.dtsi b/arch/arm64/boot/dts/qcom/msm8916.dtsi
index c1c42f26b61e..a831064700ee 100644
--- a/arch/arm64/boot/dts/qcom/msm8916.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8916.dtsi
@@ -19,8 +19,8 @@
 	#size-cells = <2>;
 
 	aliases {
-		sdhc1 = &sdhc_1; /* SDC1 eMMC slot */
-		sdhc2 = &sdhc_2; /* SDC2 SD card slot */
+		mmc0 = &sdhc_1; /* SDC1 eMMC slot */
+		mmc1 = &sdhc_2; /* SDC2 SD card slot */
 	};
 
 	chosen { };
@@ -216,7 +216,7 @@
 		};
 	};
 
-	cpu_opp_table: cpu-opp-table {
+	cpu_opp_table: opp-table-cpu {
 		compatible = "operating-points-v2";
 		opp-shared;
 
@@ -299,8 +299,10 @@
 				qcom,smd-channels = "rpm_requests";
 
 				rpmcc: clock-controller {
-					compatible = "qcom,rpmcc-msm8916";
+					compatible = "qcom,rpmcc-msm8916", "qcom,rpmcc";
 					#clock-cells = <1>;
+					clocks = <&xo_board>;
+					clock-names = "xo";
 				};
 
 				rpmpd: power-controller {
@@ -436,7 +438,7 @@
 		};
 
 		qfprom: qfprom@5c000 {
-			compatible = "qcom,qfprom";
+			compatible = "qcom,msm8916-qfprom", "qcom,qfprom";
 			reg = <0x0005c000 0x1000>;
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -453,6 +455,11 @@
 			reg = <0x00060000 0x8000>;
 		};
 
+		sram@290000 {
+			compatible = "qcom,msm8916-rpm-stats";
+			reg = <0x00290000 0x10000>;
+		};
+
 		bimc: interconnect@400000 {
 			compatible = "qcom,msm8916-bimc";
 			reg = <0x00400000 0x62000>;
@@ -929,6 +936,20 @@
 			#reset-cells = <1>;
 			#power-domain-cells = <1>;
 			reg = <0x01800000 0x80000>;
+			clocks = <&xo_board>,
+				 <&sleep_clk>,
+				 <&dsi_phy0 1>,
+				 <&dsi_phy0 0>,
+				 <0>,
+				 <0>,
+				 <0>;
+			clock-names = "xo",
+				      "sleep_clk",
+				      "dsi0pll",
+				      "dsi0pllbyte",
+				      "ext_mclk",
+				      "ext_pri_i2s",
+				      "ext_sec_i2s";
 		};
 
 		tcsr_mutex: hwlock@1905000 {
@@ -1309,6 +1330,20 @@
 			#interrupt-cells = <4>;
 		};
 
+		bam_dmux_dma: dma-controller@4044000 {
+			compatible = "qcom,bam-v1.7.0";
+			reg = <0x04044000 0x19000>;
+			interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
+			#dma-cells = <1>;
+			qcom,ee = <0>;
+
+			num-channels = <6>;
+			qcom,num-ees = <1>;
+			qcom,powered-remotely;
+
+			status = "disabled";
+		};
+
 		mpss: remoteproc@4080000 {
 			compatible = "qcom,msm8916-mss-pil", "qcom,q6v5-pil";
 			reg = <0x04080000 0x100>,
@@ -1352,6 +1387,22 @@
 				memory-region = <&mpss_mem>;
 			};
 
+			bam_dmux: bam-dmux {
+				compatible = "qcom,bam-dmux";
+
+				interrupt-parent = <&hexagon_smsm>;
+				interrupts = <1 IRQ_TYPE_EDGE_BOTH>, <11 IRQ_TYPE_EDGE_BOTH>;
+				interrupt-names = "pc", "pc-ack";
+
+				qcom,smem-states = <&apps_smsm 1>, <&apps_smsm 11>;
+				qcom,smem-state-names = "pc", "pc-ack";
+
+				dmas = <&bam_dmux_dma 4>, <&bam_dmux_dma 5>;
+				dma-names = "tx", "rx";
+
+				status = "disabled";
+			};
+
 			smd-edge {
 				interrupts = <GIC_SPI 25 IRQ_TYPE_EDGE_RISING>;
 
@@ -1365,6 +1416,7 @@
 					compatible = "qcom,fastrpc";
 					qcom,smd-channels = "fastrpcsmd-apps-dsp";
 					label = "adsp";
+					qcom,non-secure-domain;
 
 					#address-cells = <1>;
 					#size-cells = <0>;
@@ -1428,36 +1480,36 @@
 			#sound-dai-cells = <1>;
 		};
 
-		sdhc_1: sdhci@7824000 {
+		sdhc_1: mmc@7824000 {
 			compatible = "qcom,msm8916-sdhci", "qcom,sdhci-msm-v4";
 			reg = <0x07824900 0x11c>, <0x07824000 0x800>;
-			reg-names = "hc_mem", "core_mem";
+			reg-names = "hc", "core";
 
 			interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "hc_irq", "pwr_irq";
-			clocks = <&gcc GCC_SDCC1_APPS_CLK>,
-				 <&gcc GCC_SDCC1_AHB_CLK>,
+			clocks = <&gcc GCC_SDCC1_AHB_CLK>,
+				 <&gcc GCC_SDCC1_APPS_CLK>,
 				 <&xo_board>;
-			clock-names = "core", "iface", "xo";
+			clock-names = "iface", "core", "xo";
 			mmc-ddr-1_8v;
 			bus-width = <8>;
 			non-removable;
 			status = "disabled";
 		};
 
-		sdhc_2: sdhci@7864000 {
+		sdhc_2: mmc@7864000 {
 			compatible = "qcom,msm8916-sdhci", "qcom,sdhci-msm-v4";
 			reg = <0x07864900 0x11c>, <0x07864000 0x800>;
-			reg-names = "hc_mem", "core_mem";
+			reg-names = "hc", "core";
 
 			interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 221 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "hc_irq", "pwr_irq";
-			clocks = <&gcc GCC_SDCC2_APPS_CLK>,
-				 <&gcc GCC_SDCC2_AHB_CLK>,
+			clocks = <&gcc GCC_SDCC2_AHB_CLK>,
+				 <&gcc GCC_SDCC2_APPS_CLK>,
 				 <&xo_board>;
-			clock-names = "core", "iface", "xo";
+			clock-names = "iface", "core", "xo";
 			bus-width = <4>;
 			status = "disabled";
 		};
@@ -1479,8 +1531,8 @@
 			interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&gcc GCC_BLSP1_UART1_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
 			clock-names = "core", "iface";
-			dmas = <&blsp_dma 1>, <&blsp_dma 0>;
-			dma-names = "rx", "tx";
+			dmas = <&blsp_dma 0>, <&blsp_dma 1>;
+			dma-names = "tx", "rx";
 			pinctrl-names = "default", "sleep";
 			pinctrl-0 = <&blsp1_uart1_default>;
 			pinctrl-1 = <&blsp1_uart1_sleep>;
@@ -1493,8 +1545,8 @@
 			interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&gcc GCC_BLSP1_UART2_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
 			clock-names = "core", "iface";
-			dmas = <&blsp_dma 3>, <&blsp_dma 2>;
-			dma-names = "rx", "tx";
+			dmas = <&blsp_dma 2>, <&blsp_dma 3>;
+			dma-names = "tx", "rx";
 			pinctrl-names = "default", "sleep";
 			pinctrl-0 = <&blsp1_uart2_default>;
 			pinctrl-1 = <&blsp1_uart2_sleep>;
@@ -1505,9 +1557,9 @@
 			compatible = "qcom,i2c-qup-v2.2.1";
 			reg = <0x078b5000 0x500>;
 			interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc GCC_BLSP1_AHB_CLK>,
-				 <&gcc GCC_BLSP1_QUP1_I2C_APPS_CLK>;
-			clock-names = "iface", "core";
+			clocks = <&gcc GCC_BLSP1_QUP1_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
 			pinctrl-names = "default", "sleep";
 			pinctrl-0 = <&i2c1_default>;
 			pinctrl-1 = <&i2c1_sleep>;
@@ -1523,8 +1575,8 @@
 			clocks = <&gcc GCC_BLSP1_QUP1_SPI_APPS_CLK>,
 				 <&gcc GCC_BLSP1_AHB_CLK>;
 			clock-names = "core", "iface";
-			dmas = <&blsp_dma 5>, <&blsp_dma 4>;
-			dma-names = "rx", "tx";
+			dmas = <&blsp_dma 4>, <&blsp_dma 5>;
+			dma-names = "tx", "rx";
 			pinctrl-names = "default", "sleep";
 			pinctrl-0 = <&spi1_default>;
 			pinctrl-1 = <&spi1_sleep>;
@@ -1537,9 +1589,9 @@
 			compatible = "qcom,i2c-qup-v2.2.1";
 			reg = <0x078b6000 0x500>;
 			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc GCC_BLSP1_AHB_CLK>,
-				 <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>;
-			clock-names = "iface", "core";
+			clocks = <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
 			pinctrl-names = "default", "sleep";
 			pinctrl-0 = <&i2c2_default>;
 			pinctrl-1 = <&i2c2_sleep>;
@@ -1555,8 +1607,8 @@
 			clocks = <&gcc GCC_BLSP1_QUP2_SPI_APPS_CLK>,
 				 <&gcc GCC_BLSP1_AHB_CLK>;
 			clock-names = "core", "iface";
-			dmas = <&blsp_dma 7>, <&blsp_dma 6>;
-			dma-names = "rx", "tx";
+			dmas = <&blsp_dma 6>, <&blsp_dma 7>;
+			dma-names = "tx", "rx";
 			pinctrl-names = "default", "sleep";
 			pinctrl-0 = <&spi2_default>;
 			pinctrl-1 = <&spi2_sleep>;
@@ -1569,9 +1621,9 @@
 			compatible = "qcom,i2c-qup-v2.2.1";
 			reg = <0x078b7000 0x500>;
 			interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc GCC_BLSP1_AHB_CLK>,
-				 <&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>;
-			clock-names = "iface", "core";
+			clocks = <&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
 			pinctrl-names = "default", "sleep";
 			pinctrl-0 = <&i2c3_default>;
 			pinctrl-1 = <&i2c3_sleep>;
@@ -1587,8 +1639,8 @@
 			clocks = <&gcc GCC_BLSP1_QUP3_SPI_APPS_CLK>,
 				 <&gcc GCC_BLSP1_AHB_CLK>;
 			clock-names = "core", "iface";
-			dmas = <&blsp_dma 9>, <&blsp_dma 8>;
-			dma-names = "rx", "tx";
+			dmas = <&blsp_dma 8>, <&blsp_dma 9>;
+			dma-names = "tx", "rx";
 			pinctrl-names = "default", "sleep";
 			pinctrl-0 = <&spi3_default>;
 			pinctrl-1 = <&spi3_sleep>;
@@ -1601,9 +1653,9 @@
 			compatible = "qcom,i2c-qup-v2.2.1";
 			reg = <0x078b8000 0x500>;
 			interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc GCC_BLSP1_AHB_CLK>,
-				 <&gcc GCC_BLSP1_QUP4_I2C_APPS_CLK>;
-			clock-names = "iface", "core";
+			clocks = <&gcc GCC_BLSP1_QUP4_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
 			pinctrl-names = "default", "sleep";
 			pinctrl-0 = <&i2c4_default>;
 			pinctrl-1 = <&i2c4_sleep>;
@@ -1619,8 +1671,8 @@
 			clocks = <&gcc GCC_BLSP1_QUP4_SPI_APPS_CLK>,
 				 <&gcc GCC_BLSP1_AHB_CLK>;
 			clock-names = "core", "iface";
-			dmas = <&blsp_dma 11>, <&blsp_dma 10>;
-			dma-names = "rx", "tx";
+			dmas = <&blsp_dma 10>, <&blsp_dma 11>;
+			dma-names = "tx", "rx";
 			pinctrl-names = "default", "sleep";
 			pinctrl-0 = <&spi4_default>;
 			pinctrl-1 = <&spi4_sleep>;
@@ -1633,9 +1685,9 @@
 			compatible = "qcom,i2c-qup-v2.2.1";
 			reg = <0x078b9000 0x500>;
 			interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc GCC_BLSP1_AHB_CLK>,
-				 <&gcc GCC_BLSP1_QUP5_I2C_APPS_CLK>;
-			clock-names = "iface", "core";
+			clocks = <&gcc GCC_BLSP1_QUP5_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
 			pinctrl-names = "default", "sleep";
 			pinctrl-0 = <&i2c5_default>;
 			pinctrl-1 = <&i2c5_sleep>;
@@ -1651,8 +1703,8 @@
 			clocks = <&gcc GCC_BLSP1_QUP5_SPI_APPS_CLK>,
 				 <&gcc GCC_BLSP1_AHB_CLK>;
 			clock-names = "core", "iface";
-			dmas = <&blsp_dma 13>, <&blsp_dma 12>;
-			dma-names = "rx", "tx";
+			dmas = <&blsp_dma 12>, <&blsp_dma 13>;
+			dma-names = "tx", "rx";
 			pinctrl-names = "default", "sleep";
 			pinctrl-0 = <&spi5_default>;
 			pinctrl-1 = <&spi5_sleep>;
@@ -1665,9 +1717,9 @@
 			compatible = "qcom,i2c-qup-v2.2.1";
 			reg = <0x078ba000 0x500>;
 			interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc GCC_BLSP1_AHB_CLK>,
-				 <&gcc GCC_BLSP1_QUP6_I2C_APPS_CLK>;
-			clock-names = "iface", "core";
+			clocks = <&gcc GCC_BLSP1_QUP6_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
 			pinctrl-names = "default", "sleep";
 			pinctrl-0 = <&i2c6_default>;
 			pinctrl-1 = <&i2c6_sleep>;
@@ -1683,8 +1735,8 @@
 			clocks = <&gcc GCC_BLSP1_QUP6_SPI_APPS_CLK>,
 				 <&gcc GCC_BLSP1_AHB_CLK>;
 			clock-names = "core", "iface";
-			dmas = <&blsp_dma 15>, <&blsp_dma 14>;
-			dma-names = "rx", "tx";
+			dmas = <&blsp_dma 14>, <&blsp_dma 15>;
+			dma-names = "tx", "rx";
 			pinctrl-names = "default", "sleep";
 			pinctrl-0 = <&spi6_default>;
 			pinctrl-1 = <&spi6_sleep>;
@@ -1726,8 +1778,10 @@
 					clock-names = "ref", "sleep";
 					resets = <&gcc GCC_USB2A_PHY_BCR>, <&usb 0>;
 					reset-names = "phy", "por";
-					qcom,init-seq = /bits/ 8 <0x0 0x44
-						0x1 0x6b 0x2 0x24 0x3 0x13>;
+					qcom,init-seq = /bits/ 8 <0x0 0x44>,
+								 <0x1 0x6b>,
+								 <0x2 0x24>,
+								 <0x3 0x13>;
 				};
 			};
 		};
@@ -1750,8 +1804,8 @@
 					<&rpmpd MSM8916_VDDMX>;
 			power-domain-names = "cx", "mx";
 
-			qcom,state = <&wcnss_smp2p_out 0>;
-			qcom,state-names = "stop";
+			qcom,smem-states = <&wcnss_smp2p_out 0>;
+			qcom,smem-state-names = "stop";
 
 			pinctrl-names = "default";
 			pinctrl-0 = <&wcnss_pin_a>;
@@ -1780,7 +1834,7 @@
 
 					qcom,mmio = <&pronto>;
 
-					bt {
+					bluetooth {
 						compatible = "qcom,wcnss-bt";
 					};
 
@@ -1820,6 +1874,8 @@
 			compatible = "qcom,msm8916-a53pll";
 			reg = <0x0b016000 0x40>;
 			#clock-cells = <0>;
+			clocks = <&xo_board>;
+			clock-names = "xo";
 		};
 
 		timer@b020000 {
diff --git a/arch/arm64/boot/dts/qcom/msm8953.dtsi b/arch/arm64/boot/dts/qcom/msm8953.dtsi
new file mode 100644
index 000000000000..6b992a6d56c1
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/msm8953.dtsi
@@ -0,0 +1,1329 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/* Copyright (c) 2022, The Linux Foundation. All rights reserved. */
+
+#include <dt-bindings/clock/qcom,gcc-msm8953.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/power/qcom-rpmpd.h>
+#include <dt-bindings/thermal/thermal.h>
+
+/ {
+	interrupt-parent = <&intc>;
+
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	chosen { };
+
+	clocks {
+		sleep_clk: sleep-clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <32768>;
+		};
+
+		xo_board: xo-board {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <19200000>;
+			clock-output-names = "xo";
+		};
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		CPU0: cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0x0>;
+			enable-method = "psci";
+			capacity-dmips-mhz = <1024>;
+			next-level-cache = <&L2_0>;
+			#cooling-cells = <2>;
+
+			l1-icache {
+				compatible = "cache";
+			};
+			l1-dcache {
+				compatible = "cache";
+			};
+		};
+
+		CPU1: cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0x1>;
+			enable-method = "psci";
+			capacity-dmips-mhz = <1024>;
+			next-level-cache = <&L2_0>;
+			#cooling-cells = <2>;
+
+			l1-icache {
+				compatible = "cache";
+			};
+			l1-dcache {
+				compatible = "cache";
+			};
+		};
+
+		CPU2: cpu@2 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0x2>;
+			enable-method = "psci";
+			capacity-dmips-mhz = <1024>;
+			next-level-cache = <&L2_0>;
+			#cooling-cells = <2>;
+
+			l1-icache {
+				compatible = "cache";
+			};
+			l1-dcache {
+				compatible = "cache";
+			};
+		};
+
+		CPU3: cpu@3 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0x3>;
+			enable-method = "psci";
+			capacity-dmips-mhz = <1024>;
+			next-level-cache = <&L2_0>;
+			#cooling-cells = <2>;
+
+			l1-icache {
+				compatible = "cache";
+			};
+			l1-dcache {
+				compatible = "cache";
+			};
+		};
+
+		CPU4: cpu@100 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0x100>;
+			enable-method = "psci";
+			capacity-dmips-mhz = <1024>;
+			next-level-cache = <&L2_1>;
+			#cooling-cells = <2>;
+
+			l1-icache {
+				compatible = "cache";
+			};
+			l1-dcache {
+				compatible = "cache";
+			};
+		};
+
+		CPU5: cpu@101 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0x101>;
+			enable-method = "psci";
+			capacity-dmips-mhz = <1024>;
+			next-level-cache = <&L2_1>;
+			#cooling-cells = <2>;
+
+			l1-icache {
+				compatible = "cache";
+			};
+			l1-dcache {
+				compatible = "cache";
+			};
+		};
+
+		CPU6: cpu@102 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0x102>;
+			enable-method = "psci";
+			capacity-dmips-mhz = <1024>;
+			next-level-cache = <&L2_1>;
+			#cooling-cells = <2>;
+
+			l1-icache {
+				compatible = "cache";
+			};
+			l1-dcache {
+				compatible = "cache";
+			};
+		};
+
+		CPU7: cpu@103 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a53";
+			reg = <0x103>;
+			enable-method = "psci";
+			capacity-dmips-mhz = <1024>;
+			next-level-cache = <&L2_1>;
+			#cooling-cells = <2>;
+
+			l1-icache {
+				compatible = "cache";
+			};
+			l1-dcache {
+				compatible = "cache";
+			};
+		};
+
+		cpu-map {
+			cluster0 {
+				core0 {
+					cpu = <&CPU0>;
+				};
+				core1 {
+					cpu = <&CPU1>;
+				};
+				core2 {
+					cpu = <&CPU2>;
+				};
+				core3 {
+					cpu = <&CPU3>;
+				};
+			};
+
+			cluster1 {
+				core0 {
+					cpu = <&CPU4>;
+				};
+				core1 {
+					cpu = <&CPU5>;
+				};
+				core2 {
+					cpu = <&CPU6>;
+				};
+				core3 {
+					cpu = <&CPU7>;
+				};
+			};
+		};
+
+		L2_0: l2-cache_0 {
+			compatible = "cache";
+			cache-level = <2>;
+		};
+
+		L2_1: l2-cache_1 {
+			compatible = "cache";
+			cache-level = <2>;
+		};
+	};
+
+	firmware {
+		scm: scm {
+			compatible = "qcom,scm-msm8953", "qcom,scm";
+			clocks = <&gcc GCC_CRYPTO_CLK>,
+				 <&gcc GCC_CRYPTO_AXI_CLK>,
+				 <&gcc GCC_CRYPTO_AHB_CLK>;
+			clock-names = "core", "bus", "iface";
+			#reset-cells = <1>;
+		};
+	};
+
+	memory {
+		device_type = "memory";
+		/* We expect the bootloader to fill in the reg */
+		reg = <0 0 0 0>;
+	};
+
+	pmu {
+		compatible = "arm,cortex-a53-pmu";
+		interrupts = <GIC_PPI 7 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_HIGH)>;
+	};
+
+	psci {
+		compatible = "arm,psci-1.0";
+		method = "smc";
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		zap_shader_region: memory@81800000 {
+			compatible = "shared-dma-pool";
+			reg = <0x0 0x81800000 0x0 0x2000>;
+			no-map;
+		};
+
+		memory@85b00000 {
+			reg = <0x0 0x85b00000 0x0 0x800000>;
+			no-map;
+		};
+
+		smem_mem: memory@86300000 {
+			compatible = "qcom,smem";
+			reg = <0x0 0x86300000 0x0 0x100000>;
+			qcom,rpm-msg-ram = <&rpm_msg_ram>;
+			hwlocks = <&tcsr_mutex 3>;
+			no-map;
+		};
+
+		memory@86400000 {
+			reg = <0x0 0x86400000 0x0 0x400000>;
+			no-map;
+		};
+
+		mpss_mem: memory@86c00000 {
+			reg = <0x0 0x86c00000 0x0 0x6a00000>;
+			no-map;
+		};
+
+		adsp_fw_mem: memory@8d600000 {
+			reg = <0x0 0x8d600000 0x0 0x1100000>;
+			no-map;
+		};
+
+		wcnss_fw_mem: memory@8e700000 {
+			reg = <0x0 0x8e700000 0x0 0x700000>;
+			no-map;
+		};
+
+		memory@90000000 {
+			reg = <0 0x90000000 0 0x1000>;
+			no-map;
+		};
+
+		memory@90001000 {
+			reg = <0x0 0x90001000 0x0 0x13ff000>;
+			no-map;
+		};
+
+		venus_mem: memory@91400000 {
+			reg = <0x0 0x91400000 0x0 0x700000>;
+			no-map;
+		};
+
+		mba_mem: memory@92000000 {
+			reg = <0x0 0x92000000 0x0 0x100000>;
+			no-map;
+		};
+
+		memory@f2d00000 {
+			compatible = "qcom,rmtfs-mem";
+			reg = <0x0 0xf2d00000 0x0 0x180000>;
+			no-map;
+
+			qcom,client-id = <1>;
+		};
+	};
+
+	smd {
+		compatible = "qcom,smd";
+
+		rpm {
+			interrupts = <GIC_SPI 168 IRQ_TYPE_EDGE_RISING>;
+			qcom,ipc = <&apcs 8 0>;
+			qcom,smd-edge = <15>;
+
+			rpm_requests: rpm-requests {
+				compatible = "qcom,rpm-msm8953";
+				qcom,smd-channels = "rpm_requests";
+
+				rpmcc: rpmcc {
+					compatible = "qcom,rpmcc-msm8953", "qcom,rpmcc";
+					clocks = <&xo_board>;
+					clock-names = "xo";
+					#clock-cells = <1>;
+				};
+
+				rpmpd: power-controller {
+					compatible = "qcom,msm8953-rpmpd";
+					#power-domain-cells = <1>;
+					operating-points-v2 = <&rpmpd_opp_table>;
+
+					clocks = <&xo_board>;
+					clock-names = "ref";
+
+					rpmpd_opp_table: opp-table {
+						compatible = "operating-points-v2";
+
+						rpmpd_opp_ret: opp1 {
+							opp-level = <RPM_SMD_LEVEL_RETENTION>;
+						};
+
+						rpmpd_opp_ret_plus: opp2 {
+							opp-level = <RPM_SMD_LEVEL_RETENTION_PLUS>;
+						};
+
+						rpmpd_opp_min_svs: opp3 {
+							opp-level = <RPM_SMD_LEVEL_MIN_SVS>;
+						};
+
+						rpmpd_opp_low_svs: opp4 {
+							opp-level = <RPM_SMD_LEVEL_LOW_SVS>;
+						};
+
+						rpmpd_opp_svs: opp5 {
+							opp-level = <RPM_SMD_LEVEL_SVS>;
+						};
+
+						rpmpd_opp_svs_plus: opp6 {
+							opp-level = <RPM_SMD_LEVEL_SVS_PLUS>;
+						};
+
+						rpmpd_opp_nom: opp7 {
+							opp-level = <RPM_SMD_LEVEL_NOM>;
+						};
+
+						rpmpd_opp_nom_plus: opp8 {
+							opp-level = <RPM_SMD_LEVEL_NOM_PLUS>;
+						};
+
+						rpmpd_opp_turbo: opp9 {
+							opp-level = <RPM_SMD_LEVEL_TURBO>;
+						};
+					};
+				};
+			};
+		};
+	};
+
+	smsm {
+		compatible = "qcom,smsm";
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		qcom,ipc-1 = <&apcs 8 13>;
+		qcom,ipc-3 = <&apcs 8 19>;
+
+		apps_smsm: apps@0 {
+			reg = <0>;
+
+			#qcom,smem-state-cells = <1>;
+		};
+	};
+
+	soc: soc@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0 0 0xffffffff>;
+		compatible = "simple-bus";
+
+		rpm_msg_ram: sram@60000 {
+			compatible = "qcom,rpm-msg-ram";
+			reg = <0x60000 0x8000>;
+		};
+
+		hsusb_phy: phy@79000 {
+			compatible = "qcom,msm8953-qusb2-phy";
+			reg = <0x79000 0x180>;
+			#phy-cells = <0>;
+
+			clocks = <&gcc GCC_USB_PHY_CFG_AHB_CLK>,
+				 <&gcc GCC_QUSB_REF_CLK>;
+			clock-names = "cfg_ahb", "ref";
+
+			qcom,tcsr-syscon = <&tcsr_phy_clk_scheme_sel>;
+
+			resets = <&gcc GCC_QUSB2_PHY_BCR>;
+
+			status = "disabled";
+		};
+
+		rng@e3000 {
+			compatible = "qcom,prng";
+			reg = <0x000e3000 0x1000>;
+			clocks = <&gcc GCC_PRNG_AHB_CLK>;
+			clock-names = "core";
+		};
+
+		tsens0: thermal-sensor@4a9000 {
+			compatible = "qcom,msm8953-tsens", "qcom,tsens-v2";
+			reg = <0x4a9000 0x1000>, /* TM */
+			      <0x4a8000 0x1000>; /* SROT */
+			#qcom,sensors = <16>;
+			interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 314 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "uplow", "critical";
+			#thermal-sensor-cells = <1>;
+		};
+
+		restart@4ab000 {
+			compatible = "qcom,pshold";
+			reg = <0x4ab000 0x4>;
+		};
+
+		tlmm: pinctrl@1000000 {
+			compatible = "qcom,msm8953-pinctrl";
+			reg = <0x1000000 0x300000>;
+			interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
+			gpio-controller;
+			gpio-ranges = <&tlmm 0 0 155>;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+
+			uart_console_active: uart-console-active-pins {
+				pins = "gpio4", "gpio5";
+				function = "blsp_uart2";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			uart_console_sleep: uart-console-sleep-pins {
+				pins = "gpio4", "gpio5";
+				function = "blsp_uart2";
+				drive-strength = <2>;
+				bias-pull-down;
+			};
+
+			sdc1_clk_on: sdc1-clk-on-pins {
+				pins = "sdc1_clk";
+				bias-disable;
+				drive-strength = <16>;
+			};
+
+			sdc1_clk_off: sdc1-clk-off-pins {
+				pins = "sdc1_clk";
+				bias-disable;
+				drive-strength = <2>;
+			};
+
+			sdc1_cmd_on: sdc1-cmd-on-pins {
+				pins = "sdc1_cmd";
+				bias-disable;
+				drive-strength = <10>;
+			};
+
+			sdc1_cmd_off: sdc1-cmd-off-pins {
+				pins = "sdc1_cmd";
+				bias-disable;
+				drive-strength = <2>;
+			};
+
+			sdc1_data_on: sdc1-data-on-pins {
+				pins = "sdc1_data";
+				bias-pull-up;
+				drive-strength = <10>;
+			};
+
+			sdc1_data_off: sdc1-data-off-pins {
+				pins = "sdc1_data";
+				bias-pull-up;
+				drive-strength = <2>;
+			};
+
+			sdc1_rclk_on: sdc1-rclk-on-pins {
+				pins = "sdc1_rclk";
+				bias-pull-down;
+			};
+
+			sdc1_rclk_off: sdc1-rclk-off-pins {
+				pins = "sdc1_rclk";
+				bias-pull-down;
+			};
+
+			sdc2_clk_on: sdc2-clk-on-pins {
+				pins = "sdc2_clk";
+				drive-strength = <16>;
+				bias-disable;
+			};
+
+			sdc2_clk_off: sdc2-clk-off-pins {
+				pins = "sdc2_clk";
+				bias-disable;
+				drive-strength = <2>;
+			};
+
+			sdc2_cmd_on: sdc2-cmd-on-pins {
+				pins = "sdc2_cmd";
+				bias-pull-up;
+				drive-strength = <10>;
+			};
+
+			sdc2_cmd_off: sdc2-cmd-off-pins {
+				pins = "sdc2_cmd";
+				bias-pull-up;
+				drive-strength = <2>;
+			};
+
+			sdc2_data_on: sdc2-data-on-pins {
+				pins = "sdc2_data";
+				bias-pull-up;
+				drive-strength = <10>;
+			};
+
+			sdc2_data_off: sdc2-data-off-pins {
+				pins = "sdc2_data";
+				bias-pull-up;
+				drive-strength = <2>;
+			};
+
+			sdc2_cd_on: cd-on-pins {
+				pins = "gpio133";
+				function = "gpio";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			sdc2_cd_off: cd-off-pins {
+				pins = "gpio133";
+				function = "gpio";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			gpio_key_default: gpio-key-default-pins {
+				pins = "gpio85";
+				function = "gpio";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			i2c_1_default: i2c-1-default-pins {
+				pins = "gpio2", "gpio3";
+				function = "blsp_i2c1";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			i2c_1_sleep: i2c-1-sleep-pins {
+				pins = "gpio2", "gpio3";
+				function = "gpio";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			i2c_2_default: i2c-2-default-pins {
+				pins = "gpio6", "gpio7";
+				function = "blsp_i2c2";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			i2c_2_sleep: i2c-2-sleep-pins {
+				pins = "gpio6", "gpio7";
+				function = "gpio";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			i2c_3_default: i2c-3-default-pins {
+				pins = "gpio10", "gpio11";
+				function = "blsp_i2c3";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			i2c_3_sleep: i2c-3-sleep-pins {
+				pins = "gpio10", "gpio11";
+				function = "gpio";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			i2c_4_default: i2c-4-default-pins {
+				pins = "gpio14", "gpio15";
+				function = "blsp_i2c4";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			i2c_4_sleep: i2c-4-sleep-pins {
+				pins = "gpio14", "gpio15";
+				function = "gpio";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			i2c_5_default: i2c-5-default-pins {
+				pins = "gpio18", "gpio19";
+				function = "blsp_i2c5";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			i2c_5_sleep: i2c-5-sleep-pins {
+				pins = "gpio18", "gpio19";
+				function = "gpio";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			i2c_6_default: i2c-6-default-pins {
+				pins = "gpio22", "gpio23";
+				function = "blsp_i2c6";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			i2c_6_sleep: i2c-6-sleep-pins {
+				pins = "gpio22", "gpio23";
+				function = "gpio";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			i2c_7_default: i2c-7-default-pins {
+				pins = "gpio135", "gpio136";
+				function = "blsp_i2c7";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			i2c_7_sleep: i2c-7-sleep-pins {
+				pins = "gpio135", "gpio136";
+				function = "gpio";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			i2c_8_default: i2c-8-default-pins {
+				pins = "gpio98", "gpio99";
+				function = "blsp_i2c8";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			i2c_8_sleep: i2c-8-sleep-pins {
+				pins = "gpio98", "gpio99";
+				function = "gpio";
+				drive-strength = <2>;
+				bias-disable;
+			};
+		};
+
+		gcc: clock-controller@1800000 {
+			compatible = "qcom,gcc-msm8953";
+			reg = <0x1800000 0x80000>;
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+			#power-domain-cells = <1>;
+			clocks = <&xo_board>,
+				 <&sleep_clk>,
+				 <0>,
+				 <0>,
+				 <0>,
+				 <0>;
+			clock-names = "xo",
+				      "sleep",
+				      "dsi0pll",
+				      "dsi0pllbyte",
+				      "dsi1pll",
+				      "dsi1pllbyte";
+		};
+
+		tcsr_mutex: hwlock@1905000 {
+			compatible = "qcom,tcsr-mutex";
+			reg = <0x1905000 0x20000>;
+			#hwlock-cells = <1>;
+		};
+
+		tcsr: syscon@1937000 {
+			compatible = "qcom,tcsr-msm8953", "syscon";
+			reg = <0x1937000 0x30000>;
+		};
+
+		tcsr_phy_clk_scheme_sel: syscon@193f044 {
+			compatible = "qcom,tcsr-msm8953", "syscon";
+			reg = <0x193f044 0x4>;
+		};
+
+		spmi_bus: spmi@200f000 {
+			compatible = "qcom,spmi-pmic-arb";
+			reg = <0x200f000 0x1000>,
+			      <0x2400000 0x800000>,
+			      <0x2c00000 0x800000>,
+			      <0x3800000 0x200000>,
+			      <0x200a000 0x2100>;
+			reg-names = "core", "chnls", "obsrvr", "intr", "cnfg";
+			interrupt-names = "periph_irq";
+			interrupts = <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>;
+			qcom,ee = <0>;
+			qcom,channel = <0>;
+			interrupt-controller;
+
+			#interrupt-cells = <4>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+		};
+
+		usb3: usb@70f8800 {
+			compatible = "qcom,msm8953-dwc3", "qcom,dwc3";
+			reg = <0x70f8800 0x400>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			interrupts = <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hs_phy_irq", "ss_phy_irq";
+
+			clocks = <&gcc GCC_USB_PHY_CFG_AHB_CLK>,
+				 <&gcc GCC_USB30_MASTER_CLK>,
+				 <&gcc GCC_PCNOC_USB3_AXI_CLK>,
+				 <&gcc GCC_USB30_SLEEP_CLK>,
+				 <&gcc GCC_USB30_MOCK_UTMI_CLK>;
+			clock-names = "cfg_noc",
+				      "core",
+				      "iface",
+				      "sleep",
+				      "mock_utmi";
+
+			assigned-clocks = <&gcc GCC_USB30_MOCK_UTMI_CLK>,
+					  <&gcc GCC_USB30_MASTER_CLK>;
+			assigned-clock-rates = <19200000>, <133330000>;
+
+			power-domains = <&gcc USB30_GDSC>;
+
+			qcom,select-utmi-as-pipe-clk;
+
+			status = "disabled";
+
+			usb3_dwc3: usb@7000000 {
+				compatible = "snps,dwc3";
+				reg = <0x07000000 0xcc00>;
+				interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
+				phys = <&hsusb_phy>;
+				phy-names = "usb2-phy";
+
+				snps,usb2-gadget-lpm-disable;
+				snps,dis-u1-entry-quirk;
+				snps,dis-u2-entry-quirk;
+				snps,is-utmi-l1-suspend;
+				snps,hird-threshold = /bits/ 8 <0x00>;
+
+				maximum-speed = "high-speed";
+				phy_mode = "utmi";
+			};
+		};
+
+		sdhc_1: mmc@7824900 {
+			compatible = "qcom,msm8953-sdhci", "qcom,sdhci-msm-v4";
+
+			reg = <0x7824900 0x500>, <0x7824000 0x800>;
+			reg-names = "hc", "core";
+
+			interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hc_irq", "pwr_irq";
+
+			clocks = <&gcc GCC_SDCC1_AHB_CLK>,
+				 <&gcc GCC_SDCC1_APPS_CLK>,
+				 <&xo_board>;
+			clock-names = "iface", "core", "xo";
+
+			power-domains = <&rpmpd MSM8953_VDDCX>;
+			operating-points-v2 = <&sdhc1_opp_table>;
+
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on &sdc1_rclk_on>;
+			pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off &sdc1_rclk_off>;
+
+			mmc-hs400-1_8v;
+			mmc-hs200-1_8v;
+			mmc-ddr-1_8v;
+			bus-width = <8>;
+			non-removable;
+
+			status = "disabled";
+
+			sdhc1_opp_table: opp-table-sdhc1 {
+				compatible = "operating-points-v2";
+
+				opp-25000000 {
+					opp-hz = /bits/ 64 <25000000>;
+					required-opps = <&rpmpd_opp_low_svs>;
+				};
+
+				opp-50000000 {
+					opp-hz = /bits/ 64 <50000000>;
+					required-opps = <&rpmpd_opp_svs>;
+				};
+
+				opp-100000000 {
+					opp-hz = /bits/ 64 <100000000>;
+					required-opps = <&rpmpd_opp_svs>;
+				};
+
+				opp-192000000 {
+					opp-hz = /bits/ 64 <192000000>;
+					required-opps = <&rpmpd_opp_nom>;
+				};
+
+				opp-384000000 {
+					opp-hz = /bits/ 64 <384000000>;
+					required-opps = <&rpmpd_opp_nom>;
+				};
+			};
+		};
+
+		sdhc_2: mmc@7864900 {
+			compatible = "qcom,msm8953-sdhci", "qcom,sdhci-msm-v4";
+
+			reg = <0x7864900 0x500>, <0x7864000 0x800>;
+			reg-names = "hc", "core";
+
+			interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 221 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hc_irq", "pwr_irq";
+
+			clocks = <&gcc GCC_SDCC2_AHB_CLK>,
+				 <&gcc GCC_SDCC2_APPS_CLK>,
+				 <&xo_board>;
+			clock-names = "iface", "core", "xo";
+
+			power-domains = <&rpmpd MSM8953_VDDCX>;
+			operating-points-v2 = <&sdhc2_opp_table>;
+
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on>;
+			pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off>;
+
+			bus-width = <4>;
+
+			status = "disabled";
+
+			sdhc2_opp_table: opp-table-sdhc2 {
+				compatible = "operating-points-v2";
+
+				opp-25000000 {
+					opp-hz = /bits/ 64 <25000000>;
+					required-opps = <&rpmpd_opp_low_svs>;
+				};
+
+				opp-50000000 {
+					opp-hz = /bits/ 64 <50000000>;
+					required-opps = <&rpmpd_opp_svs>;
+				};
+
+				opp-100000000 {
+					opp-hz = /bits/ 64 <100000000>;
+					required-opps = <&rpmpd_opp_svs>;
+				};
+
+				opp-177770000 {
+					opp-hz = /bits/ 64 <177770000>;
+					required-opps = <&rpmpd_opp_nom>;
+				};
+
+				opp-200000000 {
+					opp-hz = /bits/ 64 <200000000>;
+					required-opps = <&rpmpd_opp_nom>;
+				};
+			};
+		};
+
+		uart_0: serial@78af000 {
+			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+			reg = <0x78af000 0x200>;
+			interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_UART1_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+
+			status = "disabled";
+		};
+
+		i2c_1: i2c@78b5000 {
+			compatible = "qcom,i2c-qup-v2.2.1";
+			reg = <0x78b5000 0x600>;
+			interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
+			clock-names = "core", "iface";
+			clocks = <&gcc GCC_BLSP1_QUP1_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&i2c_1_default>;
+			pinctrl-1 = <&i2c_1_sleep>;
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			status = "disabled";
+		};
+
+		i2c_2: i2c@78b6000 {
+			compatible = "qcom,i2c-qup-v2.2.1";
+			reg = <0x78b6000 0x600>;
+			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+			clock-names = "core", "iface";
+			clocks = <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&i2c_2_default>;
+			pinctrl-1 = <&i2c_2_sleep>;
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			status = "disabled";
+		};
+
+		i2c_3: i2c@78b7000 {
+			compatible = "qcom,i2c-qup-v2.2.1";
+			reg = <0x78b7000 0x600>;
+			interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
+			clock-names = "core", "iface";
+			clocks = <&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&i2c_3_default>;
+			pinctrl-1 = <&i2c_3_sleep>;
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			status = "disabled";
+		};
+
+		i2c_4: i2c@78b8000 {
+			compatible = "qcom,i2c-qup-v2.2.1";
+			reg = <0x78b8000 0x600>;
+			interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+			clock-names = "core", "iface";
+			clocks = <&gcc GCC_BLSP1_QUP4_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&i2c_4_default>;
+			pinctrl-1 = <&i2c_4_sleep>;
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			status = "disabled";
+		};
+
+		i2c_5: i2c@7af5000 {
+			compatible = "qcom,i2c-qup-v2.2.1";
+			reg = <0x7af5000 0x600>;
+			interrupts = <GIC_SPI 299 IRQ_TYPE_LEVEL_HIGH>;
+			clock-names = "core", "iface";
+			clocks = <&gcc GCC_BLSP2_QUP1_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP2_AHB_CLK>;
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&i2c_5_default>;
+			pinctrl-1 = <&i2c_5_sleep>;
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			status = "disabled";
+		};
+
+		i2c_6: i2c@7af6000 {
+			compatible = "qcom,i2c-qup-v2.2.1";
+			reg = <0x7af6000 0x600>;
+			interrupts = <GIC_SPI 300 IRQ_TYPE_LEVEL_HIGH>;
+			clock-names = "core", "iface";
+			clocks = <&gcc GCC_BLSP2_QUP2_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP2_AHB_CLK>;
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&i2c_6_default>;
+			pinctrl-1 = <&i2c_6_sleep>;
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			status = "disabled";
+		};
+
+		i2c_7: i2c@7af7000 {
+			compatible = "qcom,i2c-qup-v2.2.1";
+			reg = <0x7af7000 0x600>;
+			interrupts = <GIC_SPI 301 IRQ_TYPE_LEVEL_HIGH>;
+			clock-names = "core", "iface";
+			clocks = <&gcc GCC_BLSP2_QUP3_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP2_AHB_CLK>;
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&i2c_7_default>;
+			pinctrl-1 = <&i2c_7_sleep>;
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			status = "disabled";
+		};
+
+		i2c_8: i2c@7af8000 {
+			compatible = "qcom,i2c-qup-v2.2.1";
+			reg = <0x7af8000 0x600>;
+			interrupts = <GIC_SPI 302 IRQ_TYPE_LEVEL_HIGH>;
+			clock-names = "core", "iface";
+			clocks = <&gcc GCC_BLSP2_QUP4_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP2_AHB_CLK>;
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&i2c_8_default>;
+			pinctrl-1 = <&i2c_8_sleep>;
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			status = "disabled";
+		};
+
+		intc: interrupt-controller@b000000 {
+			compatible = "qcom,msm-qgic2";
+			interrupt-controller;
+			#interrupt-cells = <3>;
+			reg = <0x0b000000 0x1000>, <0x0b002000 0x1000>;
+		};
+
+		apcs: mailbox@b011000 {
+			compatible = "qcom,msm8953-apcs-kpss-global", "syscon";
+			reg = <0xb011000 0x1000>;
+			#mbox-cells = <1>;
+		};
+
+		timer@b120000 {
+			compatible = "arm,armv7-timer-mem";
+			reg = <0xb120000 0x1000>;
+			#address-cells = <0x01>;
+			#size-cells = <0x01>;
+			ranges;
+
+			frame@b121000 {
+				frame-number = <0>;
+				interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0xb121000 0x1000>,
+				      <0xb122000 0x1000>;
+			};
+
+			frame@b123000 {
+				frame-number = <1>;
+				interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0xb123000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@b124000 {
+				frame-number = <2>;
+				interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0xb124000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@b125000 {
+				frame-number = <3>;
+				interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0xb125000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@b126000 {
+				frame-number = <4>;
+				interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0xb126000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@b127000 {
+				frame-number = <5>;
+				interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0xb127000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@b128000 {
+				frame-number = <6>;
+				interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0xb128000 0x1000>;
+				status = "disabled";
+			};
+		};
+	};
+
+	thermal-zones {
+		cpu0-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+			thermal-sensors = <&tsens0 9>;
+			trips {
+				cpu0_alert: trip-point0 {
+					temperature = <80000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+				cpu0_crit: crit {
+					temperature = <100000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+			cooling-maps {
+				map0 {
+					trip = <&cpu0_alert>;
+					cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+		cpu1-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+			thermal-sensors = <&tsens0 10>;
+			trips {
+				cpu1_alert: trip-point0 {
+					temperature = <80000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+				cpu1_crit: crit {
+					temperature = <100000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+			cooling-maps {
+				map0 {
+					trip = <&cpu1_alert>;
+					cooling-device = <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+		cpu2-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+			thermal-sensors = <&tsens0 11>;
+			trips {
+				cpu2_alert: trip-point0 {
+					temperature = <80000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+				cpu2_crit: crit {
+					temperature = <100000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+			cooling-maps {
+				map0 {
+					trip = <&cpu2_alert>;
+					cooling-device = <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+		cpu3-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+			thermal-sensors = <&tsens0 12>;
+			trips {
+				cpu3_alert: trip-point0 {
+					temperature = <80000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+				cpu3_crit: crit {
+					temperature = <100000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+			cooling-maps {
+				map0 {
+					trip = <&cpu3_alert>;
+					cooling-device = <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+		cpu4-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+			thermal-sensors = <&tsens0 4>;
+			trips {
+				cpu4_alert: trip-point0 {
+					temperature = <80000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+				cpu4_crit: crit {
+					temperature = <100000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+			cooling-maps {
+				map0 {
+					trip = <&cpu4_alert>;
+					cooling-device = <&CPU4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+		cpu5-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+			thermal-sensors = <&tsens0 5>;
+			trips {
+				cpu5_alert: trip-point0 {
+					temperature = <80000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+				cpu5_crit: crit {
+					temperature = <100000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+			cooling-maps {
+				map0 {
+					trip = <&cpu5_alert>;
+					cooling-device = <&CPU5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+		cpu6-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+			thermal-sensors = <&tsens0 6>;
+			trips {
+				cpu6_alert: trip-point0 {
+					temperature = <80000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+				cpu6_crit: crit {
+					temperature = <100000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+			cooling-maps {
+				map0 {
+					trip = <&cpu6_alert>;
+					cooling-device = <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+		cpu7-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+			thermal-sensors = <&tsens0 7>;
+			trips {
+				cpu7_alert: trip-point0 {
+					temperature = <80000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+				cpu7_crit: crit {
+					temperature = <100000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+			cooling-maps {
+				map0 {
+					trip = <&cpu7_alert>;
+					cooling-device = <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupts = <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 4 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>;
+	};
+};
diff --git a/arch/arm64/boot/dts/qcom/msm8992-bullhead-rev-101.dts b/arch/arm64/boot/dts/qcom/msm8992-bullhead-rev-101.dts
deleted file mode 100644
index 4da6c44bf532..000000000000
--- a/arch/arm64/boot/dts/qcom/msm8992-bullhead-rev-101.dts
+++ /dev/null
@@ -1,304 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/* Copyright (c) 2015, LGE Inc. All rights reserved.
- * Copyright (c) 2016, The Linux Foundation. All rights reserved.
- * Copyright (c) 2021, Petr Vorel <petr.vorel@gmail.com>
- */
-
-/dts-v1/;
-
-#include "msm8992.dtsi"
-#include "pm8994.dtsi"
-#include "pmi8994.dtsi"
-
-/* cont_splash_mem has different memory mapping */
-/delete-node/ &cont_splash_mem;
-
-/ {
-	model = "LG Nexus 5X";
-	compatible = "lg,bullhead", "qcom,msm8992";
-	chassis-type = "handset";
-
-	/* required for bootloader to select correct board */
-	qcom,msm-id = <251 0>, <252 0>;
-	qcom,board-id = <0xb64 0>;
-	qcom,pmic-id = <0x10009 0x1000A 0x0 0x0>;
-
-	/* Bullhead firmware doesn't support PSCI */
-	/delete-node/ psci;
-
-	aliases {
-		serial0 = &blsp1_uart2;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	reserved-memory {
-		#address-cells = <2>;
-		#size-cells = <2>;
-		ranges;
-
-		ramoops@1ff00000 {
-			compatible = "ramoops";
-			reg = <0x0 0x1ff00000 0x0 0x40000>;
-			console-size = <0x10000>;
-			record-size = <0x10000>;
-			ftrace-size = <0x10000>;
-			pmsg-size = <0x20000>;
-		};
-
-		cont_splash_mem: memory@3400000 {
-			reg = <0 0x03400000 0 0x1200000>;
-			no-map;
-		};
-	};
-};
-
-&blsp1_uart2 {
-	status = "okay";
-};
-
-&rpm_requests {
-	pm8994_regulators: pm8994-regulators {
-		compatible = "qcom,rpm-pm8994-regulators";
-
-		vdd_l1-supply = <&pm8994_s1>;
-		vdd_l2_26_28-supply = <&pm8994_s3>;
-		vdd_l3_11-supply = <&pm8994_s3>;
-		vdd_l4_27_31-supply = <&pm8994_s3>;
-		vdd_l5_7-supply = <&pm8994_s3>;
-		vdd_l6_12_32-supply = <&pm8994_s5>;
-		vdd_l8_16_30-supply = <&vph_pwr>;
-		vdd_l9_10_18_22-supply = <&vph_pwr>;
-		vdd_l13_19_23_24-supply = <&vph_pwr>;
-		vdd_l14_15-supply = <&pm8994_s5>;
-		vdd_l17_29-supply = <&vph_pwr>;
-		vdd_l20_21-supply = <&vph_pwr>;
-		vdd_l25-supply = <&pm8994_s5>;
-		vdd_lvs1_2 = <&pm8994_s4>;
-
-		/* S1, S2, S6 and S12 are managed by RPMPD */
-
-		pm8994_s1: s1 {
-			regulator-min-microvolt = <800000>;
-			regulator-max-microvolt = <800000>;
-		};
-
-		pm8994_s2: s2 {
-			/* TODO */
-		};
-
-		pm8994_s3: s3 {
-			regulator-min-microvolt = <1300000>;
-			regulator-max-microvolt = <1300000>;
-		};
-
-		pm8994_s4: s4 {
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-			regulator-allow-set-load;
-			regulator-system-load = <325000>;
-		};
-
-		pm8994_s5: s5 {
-			regulator-min-microvolt = <2150000>;
-			regulator-max-microvolt = <2150000>;
-		};
-
-		pm8994_s7: s7 {
-			regulator-min-microvolt = <1000000>;
-			regulator-max-microvolt = <1000000>;
-		};
-
-		/* S8, S9, S10 and S11 - SPMI-managed VDD_APC */
-
-		pm8994_l1: l1 {
-			regulator-min-microvolt = <1000000>;
-			regulator-max-microvolt = <1000000>;
-		};
-
-		pm8994_l2: l2 {
-			regulator-min-microvolt = <1250000>;
-			regulator-max-microvolt = <1250000>;
-		};
-
-		pm8994_l3: l3 {
-			regulator-min-microvolt = <1200000>;
-			regulator-max-microvolt = <1200000>;
-		};
-
-		pm8994_l4: l4 {
-			regulator-min-microvolt = <1225000>;
-			regulator-max-microvolt = <1225000>;
-		};
-
-		/* L5 is inaccessible from RPM */
-
-		pm8994_l6: l6 {
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-		};
-
-		/* L7 is inaccessible from RPM */
-
-		pm8994_l8: l8 {
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-		};
-
-		pm8994_l9: l9 {
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-		};
-
-		pm8994_l10: l10 {
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-		};
-
-		pm8994_l11: l11 {
-			regulator-min-microvolt = <1200000>;
-			regulator-max-microvolt = <1200000>;
-		};
-
-		pm8994_l12: l12 {
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-		};
-
-		pm8994_l13: l13 {
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <2950000>;
-		};
-
-		pm8994_l14: l14 {
-			regulator-min-microvolt = <1200000>;
-			regulator-max-microvolt = <1200000>;
-		};
-
-		pm8994_l15: l15 {
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-		};
-
-		pm8994_l16: l16 {
-			regulator-min-microvolt = <2700000>;
-			regulator-max-microvolt = <2700000>;
-		};
-
-		pm8994_l17: l17 {
-			regulator-min-microvolt = <2700000>;
-			regulator-max-microvolt = <2700000>;
-		};
-
-		pm8994_l18: l18 {
-			regulator-min-microvolt = <3000000>;
-			regulator-max-microvolt = <3000000>;
-		};
-
-		pm8994_l19: l19 {
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-		};
-
-		pm8994_l20: l20 {
-			regulator-min-microvolt = <2950000>;
-			regulator-max-microvolt = <2950000>;
-			regulator-always-on;
-			regulator-boot-on;
-			regulator-allow-set-load;
-			regulator-system-load = <570000>;
-		};
-
-		pm8994_l21: l21 {
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-			regulator-always-on;
-		};
-
-		pm8994_l22: l22 {
-			regulator-min-microvolt = <3100000>;
-			regulator-max-microvolt = <3100000>;
-		};
-
-		pm8994_l23: l23 {
-			regulator-min-microvolt = <2800000>;
-			regulator-max-microvolt = <2800000>;
-		};
-
-		pm8994_l24: l24 {
-			regulator-min-microvolt = <3075000>;
-			regulator-max-microvolt = <3150000>;
-		};
-
-		pm8994_l25: l25 {
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-		};
-
-		pm8994_l26: l26 {
-			/* TODO: value from downstream
-			regulator-min-microvolt = <987500>;
-			fails to apply */
-		};
-
-		pm8994_l27: l27 {
-			regulator-min-microvolt = <1050000>;
-			regulator-max-microvolt = <1050000>;
-		};
-
-		pm8994_l28: l28 {
-			regulator-min-microvolt = <1000000>;
-			regulator-max-microvolt = <1000000>;
-		};
-
-		pm8994_l29: l29 {
-			/* TODO: Unsupported voltage range.
-			regulator-min-microvolt = <2800000>;
-			regulator-max-microvolt = <2800000>;
-			qcom,init-voltage = <2800000>;
-			*/
-		};
-
-		pm8994_l30: l30 {
-			/* TODO: get this verified
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-			qcom,init-voltage = <1800000>;
-			*/
-		};
-
-		pm8994_l31: l31 {
-			regulator-min-microvolt = <1262500>;
-			regulator-max-microvolt = <1262500>;
-		};
-
-		pm8994_l32: l32 {
-			/* TODO: get this verified
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-			qcom,init-voltage = <1800000>;
-			*/
-		};
-	};
-
-	pmi8994_regulators: pmi8994-regulators {
-		compatible = "qcom,rpm-pmi8994-regulators";
-
-		vdd_s1-supply = <&vph_pwr>;
-		vdd_bst_byp-supply = <&vph_pwr>;
-
-		pmi8994_s1: s1 {};
-
-		/* S2 & S3 - VDD_GFX */
-
-		pmi8994_bby: boost-bypass {};
-	};
-};
-
-&sdhc1 {
-	status = "okay";
-
-	mmc-hs400-1_8v;
-};
diff --git a/arch/arm64/boot/dts/qcom/msm8992-lg-bullhead-rev-10.dts b/arch/arm64/boot/dts/qcom/msm8992-lg-bullhead-rev-10.dts
new file mode 100644
index 000000000000..7e6bce4af441
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/msm8992-lg-bullhead-rev-10.dts
@@ -0,0 +1,14 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/* Copyright (c) Jean Thomas <virgule@jeanthomas.me>
+ */
+
+/dts-v1/;
+
+#include "msm8992-lg-bullhead.dtsi"
+
+/ {
+	model = "LG Nexus 5X rev 1.0";
+
+	/* required for bootloader to select correct board */
+	qcom,board-id = <0xa64 0>;
+};
diff --git a/arch/arm64/boot/dts/qcom/msm8992-lg-bullhead-rev-101.dts b/arch/arm64/boot/dts/qcom/msm8992-lg-bullhead-rev-101.dts
new file mode 100644
index 000000000000..e6a5ebd30e2f
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/msm8992-lg-bullhead-rev-101.dts
@@ -0,0 +1,14 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/* Copyright (c) Jean Thomas <virgule@jeanthomas.me>
+ */
+
+/dts-v1/;
+
+#include "msm8992-lg-bullhead.dtsi"
+
+/ {
+	model = "LG Nexus 5X rev 1.01";
+
+	/* required for bootloader to select correct board */
+	qcom,board-id = <0xb64 0>;
+};
diff --git a/arch/arm64/boot/dts/qcom/msm8992-lg-bullhead.dtsi b/arch/arm64/boot/dts/qcom/msm8992-lg-bullhead.dtsi
new file mode 100644
index 000000000000..71e373b11de9
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/msm8992-lg-bullhead.dtsi
@@ -0,0 +1,302 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/* Copyright (c) 2015, LGE Inc. All rights reserved.
+ * Copyright (c) 2016, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2021, Petr Vorel <petr.vorel@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "msm8992.dtsi"
+#include "pm8994.dtsi"
+#include "pmi8994.dtsi"
+
+/* cont_splash_mem has different memory mapping */
+/delete-node/ &cont_splash_mem;
+
+/ {
+	model = "LG Nexus 5X";
+	compatible = "lg,bullhead", "qcom,msm8992";
+	chassis-type = "handset";
+
+	qcom,msm-id = <251 0>, <252 0>;
+	qcom,pmic-id = <0x10009 0x1000A 0x0 0x0>;
+
+	/* Bullhead firmware doesn't support PSCI */
+	/delete-node/ psci;
+
+	aliases {
+		serial0 = &blsp1_uart2;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		ramoops@1ff00000 {
+			compatible = "ramoops";
+			reg = <0x0 0x1ff00000 0x0 0x40000>;
+			console-size = <0x10000>;
+			record-size = <0x10000>;
+			ftrace-size = <0x10000>;
+			pmsg-size = <0x20000>;
+		};
+
+		cont_splash_mem: memory@3400000 {
+			reg = <0 0x03400000 0 0x1200000>;
+			no-map;
+		};
+	};
+};
+
+&blsp1_uart2 {
+	status = "okay";
+};
+
+&rpm_requests {
+	pm8994_regulators: pm8994-regulators {
+		compatible = "qcom,rpm-pm8994-regulators";
+
+		vdd_l1-supply = <&pm8994_s1>;
+		vdd_l2_26_28-supply = <&pm8994_s3>;
+		vdd_l3_11-supply = <&pm8994_s3>;
+		vdd_l4_27_31-supply = <&pm8994_s3>;
+		vdd_l5_7-supply = <&pm8994_s3>;
+		vdd_l6_12_32-supply = <&pm8994_s5>;
+		vdd_l8_16_30-supply = <&vph_pwr>;
+		vdd_l9_10_18_22-supply = <&vph_pwr>;
+		vdd_l13_19_23_24-supply = <&vph_pwr>;
+		vdd_l14_15-supply = <&pm8994_s5>;
+		vdd_l17_29-supply = <&vph_pwr>;
+		vdd_l20_21-supply = <&vph_pwr>;
+		vdd_l25-supply = <&pm8994_s5>;
+		vdd_lvs1_2-supply = <&pm8994_s4>;
+
+		/* S1, S2, S6 and S12 are managed by RPMPD */
+
+		pm8994_s1: s1 {
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <800000>;
+		};
+
+		pm8994_s2: s2 {
+			/* TODO */
+		};
+
+		pm8994_s3: s3 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1300000>;
+		};
+
+		pm8994_s4: s4 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-allow-set-load;
+			regulator-system-load = <325000>;
+		};
+
+		pm8994_s5: s5 {
+			regulator-min-microvolt = <2150000>;
+			regulator-max-microvolt = <2150000>;
+		};
+
+		pm8994_s7: s7 {
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1000000>;
+		};
+
+		/* S8, S9, S10 and S11 - SPMI-managed VDD_APC */
+
+		pm8994_l1: l1 {
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1000000>;
+		};
+
+		pm8994_l2: l2 {
+			regulator-min-microvolt = <1250000>;
+			regulator-max-microvolt = <1250000>;
+		};
+
+		pm8994_l3: l3 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8994_l4: l4 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+		};
+
+		/* L5 is inaccessible from RPM */
+
+		pm8994_l6: l6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		/* L7 is inaccessible from RPM */
+
+		pm8994_l8: l8 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8994_l9: l9 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8994_l10: l10 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8994_l11: l11 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8994_l12: l12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8994_l13: l13 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8994_l14: l14 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8994_l15: l15 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8994_l16: l16 {
+			regulator-min-microvolt = <2700000>;
+			regulator-max-microvolt = <2700000>;
+		};
+
+		pm8994_l17: l17 {
+			regulator-min-microvolt = <2700000>;
+			regulator-max-microvolt = <2700000>;
+		};
+
+		pm8994_l18: l18 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+		};
+
+		pm8994_l19: l19 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8994_l20: l20 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-always-on;
+			regulator-boot-on;
+			regulator-allow-set-load;
+			regulator-system-load = <570000>;
+		};
+
+		pm8994_l21: l21 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+		};
+
+		pm8994_l22: l22 {
+			regulator-min-microvolt = <3100000>;
+			regulator-max-microvolt = <3100000>;
+		};
+
+		pm8994_l23: l23 {
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+		};
+
+		pm8994_l24: l24 {
+			regulator-min-microvolt = <3075000>;
+			regulator-max-microvolt = <3150000>;
+		};
+
+		pm8994_l25: l25 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8994_l26: l26 {
+			/* TODO: value from downstream
+			regulator-min-microvolt = <987500>;
+			fails to apply */
+		};
+
+		pm8994_l27: l27 {
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1050000>;
+		};
+
+		pm8994_l28: l28 {
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1000000>;
+		};
+
+		pm8994_l29: l29 {
+			/* TODO: Unsupported voltage range.
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+			qcom,init-voltage = <2800000>;
+			*/
+		};
+
+		pm8994_l30: l30 {
+			/* TODO: get this verified
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			qcom,init-voltage = <1800000>;
+			*/
+		};
+
+		pm8994_l31: l31 {
+			regulator-min-microvolt = <1262500>;
+			regulator-max-microvolt = <1262500>;
+		};
+
+		pm8994_l32: l32 {
+			/* TODO: get this verified
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			qcom,init-voltage = <1800000>;
+			*/
+		};
+	};
+
+	pmi8994_regulators: pmi8994-regulators {
+		compatible = "qcom,rpm-pmi8994-regulators";
+
+		vdd_s1-supply = <&vph_pwr>;
+		vdd_bst_byp-supply = <&vph_pwr>;
+
+		pmi8994_s1: s1 {};
+
+		/* S2 & S3 - VDD_GFX */
+
+		pmi8994_bby: boost-bypass {};
+	};
+};
+
+&sdhc1 {
+	status = "okay";
+
+	mmc-hs400-1_8v;
+};
diff --git a/arch/arm64/boot/dts/qcom/msm8992-xiaomi-libra.dts b/arch/arm64/boot/dts/qcom/msm8992-xiaomi-libra.dts
index 69fcb6b0398d..c4e87d0aec42 100644
--- a/arch/arm64/boot/dts/qcom/msm8992-xiaomi-libra.dts
+++ b/arch/arm64/boot/dts/qcom/msm8992-xiaomi-libra.dts
@@ -17,37 +17,45 @@
 	chassis-type = "handset";
 
 	/* required for bootloader to select correct board */
-	qcom,msm-id = <251 0 252 0>;
+	qcom,msm-id = <251 0>, <252 0>;
 	qcom,pmic-id = <65545 65546 0 0>;
 	qcom,board-id = <12 0>;
 
 	/* This enables graphical output via bootloader-enabled display */
 	chosen {
-		bootargs = "earlycon=tty0 console=tty0";
+		bootargs = "earlycon=tty0 console=tty0 maxcpus=1";
 
 		#address-cells = <2>;
 		#size-cells = <2>;
 		ranges;
 
-		framebuffer0: framebuffer@3404000 {
-			status= "okay";
+		framebuffer0: framebuffer@3400000 {
 			compatible = "simple-framebuffer";
-			reg = <0 0x3404000 0 (1080 * 1920 * 3)>;
+			reg = <0 0x3400000 0 (1080 * 1920 * 3)>;
 			width = <1080>;
 			height = <1920>;
 			stride = <(1080 * 3)>;
 			format = "r8g8b8";
+			/*
+			 * That's a lot of clocks, but it's necessary due
+			 * to unused clk cleanup & no panel driver yet..
+			 */
+			clocks = <&mmcc MDSS_AHB_CLK>,
+				 <&mmcc MDSS_AXI_CLK>,
+				 <&mmcc MDSS_VSYNC_CLK>,
+				 <&mmcc MDSS_MDP_CLK>,
+				 <&mmcc MDSS_BYTE0_CLK>,
+				 <&mmcc MDSS_PCLK0_CLK>,
+				 <&mmcc MDSS_ESC0_CLK>;
+			power-domains = <&mmcc MDSS_GDSC>;
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
-		input-name = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		autorepeat;
 
-		button@0 {
+		button {
 			label = "Volume Up";
 			gpios = <&pm8994_gpios 3 GPIO_ACTIVE_LOW>;
 			linux,input-type = <1>;
@@ -127,6 +135,23 @@
 	no-map;
 };
 
+&pm8994_spmi_regulators {
+	VDD_APC0: s8 {
+		regulator-min-microvolt = <680000>;
+		regulator-max-microvolt = <1180000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	/* APC1 is 3-phase, but quoting downstream, s11 is "the gang leader" */
+	VDD_APC1: s11 {
+		regulator-min-microvolt = <700000>;
+		regulator-max-microvolt = <1225000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+};
+
 &rpm_requests {
 	pm8994-regulators {
 		compatible = "qcom,rpm-pm8994-regulators";
@@ -144,7 +169,7 @@
 		vdd_l17_29-supply = <&vph_pwr>;
 		vdd_l20_21-supply = <&vph_pwr>;
 		vdd_l25-supply = <&pm8994_s5>;
-		vdd_lvs1_2 = <&pm8994_s4>;
+		vdd_lvs1_2-supply = <&pm8994_s4>;
 
 		/* S1, S2, S6 and S12 are managed by RPMPD */
 
diff --git a/arch/arm64/boot/dts/qcom/msm8992.dtsi b/arch/arm64/boot/dts/qcom/msm8992.dtsi
index 58fe58cc7703..750643763a76 100644
--- a/arch/arm64/boot/dts/qcom/msm8992.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8992.dtsi
@@ -10,8 +10,30 @@
 /delete-node/ &cpu6_map;
 /delete-node/ &cpu7_map;
 
+&gcc {
+	compatible = "qcom,gcc-msm8992";
+};
+
+&mmcc {
+	compatible = "qcom,mmcc-msm8992";
+
+	assigned-clock-rates = <800000000>,
+			       <808000000>,
+			       <1020000000>,
+			       <960000000>,
+			       <800000000>;
+};
+
+&ocmem {
+	reg = <0xfdd00000 0x2000>, <0xfec00000 0x100000>;
+
+	gmu-sram@0 {
+		reg = <0x0 0x80000>;
+	};
+};
+
 &rpmcc {
-	compatible = "qcom,rpmcc-msm8992";
+	compatible = "qcom,rpmcc-msm8992", "qcom,rpmcc";
 };
 
 &tcsr_mutex {
diff --git a/arch/arm64/boot/dts/qcom/msm8994-angler-rev-101.dts b/arch/arm64/boot/dts/qcom/msm8994-angler-rev-101.dts
deleted file mode 100644
index 0e3dd48f0dbf..000000000000
--- a/arch/arm64/boot/dts/qcom/msm8994-angler-rev-101.dts
+++ /dev/null
@@ -1,43 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/* Copyright (c) 2015, Huawei Inc. All rights reserved.
- * Copyright (c) 2016, The Linux Foundation. All rights reserved.
- * Copyright (c) 2021, Petr Vorel <petr.vorel@gmail.com>
- */
-
-/dts-v1/;
-
-#include "msm8994.dtsi"
-
-/* Angler's firmware does not report where the memory is allocated */
-/delete-node/ &cont_splash_mem;
-
-/ {
-	model = "Huawei Nexus 6P";
-	compatible = "huawei,angler", "qcom,msm8994";
-	chassis-type = "handset";
-	/* required for bootloader to select correct board */
-	qcom,msm-id = <207 0x20000>;
-	qcom,pmic-id = <0x10009 0x1000A 0x0 0x0>;
-	qcom,board-id = <8026 0>;
-
-	aliases {
-		serial0 = &blsp1_uart2;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	soc {
-		serial@f991e000 {
-			status = "okay";
-			pinctrl-names = "default", "sleep";
-			pinctrl-0 = <&blsp1_uart2_default>;
-			pinctrl-1 = <&blsp1_uart2_sleep>;
-		};
-	};
-};
-
-&tlmm {
-	gpio-reserved-ranges = <85 4>;
-};
diff --git a/arch/arm64/boot/dts/qcom/msm8994-huawei-angler-rev-101.dts b/arch/arm64/boot/dts/qcom/msm8994-huawei-angler-rev-101.dts
new file mode 100644
index 000000000000..dbfbb77e9ff5
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/msm8994-huawei-angler-rev-101.dts
@@ -0,0 +1,46 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/* Copyright (c) 2015, Huawei Inc. All rights reserved.
+ * Copyright (c) 2016, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2021-2022, Petr Vorel <petr.vorel@gmail.com>
+ */
+
+/dts-v1/;
+
+#include "msm8994.dtsi"
+
+/* Angler's firmware does not report where the memory is allocated */
+/delete-node/ &cont_splash_mem;
+
+/ {
+	model = "Huawei Nexus 6P";
+	compatible = "huawei,angler", "qcom,msm8994";
+	chassis-type = "handset";
+	/* required for bootloader to select correct board */
+	qcom,msm-id = <207 0x20000>;
+	qcom,pmic-id = <0x10009 0x1000A 0x0 0x0>;
+	qcom,board-id = <8026 0>;
+
+	aliases {
+		serial0 = &blsp1_uart2;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
+
+&blsp1_uart2 {
+	status = "okay";
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&blsp1_uart2_default>;
+	pinctrl-1 = <&blsp1_uart2_sleep>;
+};
+
+&tlmm {
+	gpio-reserved-ranges = <85 4>;
+};
+
+&sdhc1 {
+	status = "okay";
+	mmc-hs400-1_8v;
+};
diff --git a/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon.dtsi b/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon.dtsi
index 3a3790a52a2c..f9d8bd09e074 100644
--- a/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8994-msft-lumia-octagon.dtsi
@@ -62,10 +62,9 @@
 
 	gpio-keys {
 		compatible = "gpio-keys";
-		input-name = "gpio-keys";
 		autorepeat;
 
-		volupkey {
+		volup-key {
 			label = "Volume Up";
 			gpios = <&pm8994_gpios 3 GPIO_ACTIVE_LOW>;
 			linux,input-type = <1>;
@@ -74,7 +73,7 @@
 			debounce-interval = <15>;
 		};
 
-		camsnapkey {
+		camsnap-key {
 			label = "Camera Snapshot";
 			gpios = <&pm8994_gpios 4 GPIO_ACTIVE_LOW>;
 			linux,input-type = <1>;
@@ -83,7 +82,7 @@
 			debounce-interval = <15>;
 		};
 
-		camfocuskey {
+		camfocus-key {
 			label = "Camera Focus";
 			gpios = <&pm8994_gpios 5 GPIO_ACTIVE_LOW>;
 			linux,input-type = <1>;
@@ -101,7 +100,7 @@
 
 		label = "GPIO Hall Effect Sensor";
 
-		hall-front-sensor {
+		event-hall-front-sensor {
 			label = "Hall Effect Front Sensor";
 			gpios = <&tlmm 42 GPIO_ACTIVE_HIGH>;
 			linux,input-type = <EV_SW>;
@@ -109,7 +108,7 @@
 			linux,can-disable;
 		};
 
-		hall-back-sensor {
+		event-hall-back-sensor {
 			label = "Hall Effect Back Sensor";
 			gpios = <&tlmm 75 GPIO_ACTIVE_HIGH>;
 			linux,input-type = <EV_SW>;
@@ -471,7 +470,7 @@
 };
 
 &pm8994_gpios {
-	bt_en_gpios: bt_en_gpios {
+	bt_en_gpios: bt-en-gpios-state {
 		pinconf {
 			pins = "gpio19";
 			function = PMIC_GPIO_FUNC_NORMAL;
@@ -482,7 +481,7 @@
 		};
 	};
 
-	divclk4_pin_a: divclk4 {
+	divclk4_pin_a: divclk4-state {
 		pinconf {
 			pins = "gpio18";
 			function = PMIC_GPIO_FUNC_FUNC2;
@@ -500,7 +499,7 @@
 		linux,code = <KEY_POWER>;
 	};
 
-	volwnkey {
+	resin {
 		compatible = "qcom,pm8941-resin";
 		interrupts = <0 8 1 IRQ_TYPE_EDGE_BOTH>;
 		debounce = <15625>;
@@ -520,21 +519,24 @@
 	 * TODO: remove once a driver is available
 	 * TODO: add VBUS GPIO 5
 	 */
-	hd3ss460_pol: pol_low {
+	hd3ss460_pol: pol-low-state {
 		pins = "gpio8";
-		drive-strength = <3>;
+		function = PMIC_GPIO_FUNC_NORMAL;
+		qcom,drive-strength = <3>;
 		bias-pull-down;
 	};
 
-	hd3ss460_amsel: amsel_high {
+	hd3ss460_amsel: amsel-high-state {
 		pins = "gpio9";
-		drive-strength = <1>;
+		function = PMIC_GPIO_FUNC_NORMAL;
+		qcom,drive-strength = <1>;
 		bias-pull-up;
 	};
 
-	hd3ss460_en: en_high {
+	hd3ss460_en: en-high-state {
 		pins = "gpio10";
-		drive-strength = <1>;
+		function = PMIC_GPIO_FUNC_NORMAL;
+		qcom,drive-strength = <1>;
 		bias-pull-up;
 	};
 };
diff --git a/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami.dtsi b/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami.dtsi
index 48de66bf19c4..ff60b7004d26 100644
--- a/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8994-sony-xperia-kitakami.dtsi
@@ -27,14 +27,11 @@
 	/* Kitakami firmware doesn't support PSCI */
 	/delete-node/ psci;
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
-		input-name = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		autorepeat;
 
-		button@0 {
+		button-0 {
 			label = "Volume Down";
 			gpios = <&pm8994_gpios 2 GPIO_ACTIVE_LOW>;
 			linux,input-type = <1>;
@@ -43,7 +40,7 @@
 			debounce-interval = <15>;
 		};
 
-		button@1 {
+		button-1 {
 			label = "Volume Up";
 			gpios = <&pm8994_gpios 3 GPIO_ACTIVE_LOW>;
 			linux,input-type = <1>;
@@ -52,7 +49,7 @@
 			debounce-interval = <15>;
 		};
 
-		button@2 {
+		button-2 {
 			label = "Camera Snapshot";
 			gpios = <&pm8994_gpios 4 GPIO_ACTIVE_LOW>;
 			linux,input-type = <1>;
@@ -61,7 +58,7 @@
 			debounce-interval = <15>;
 		};
 
-		button@3 {
+		button-3 {
 			label = "Camera Focus";
 			gpios = <&pm8994_gpios 5 GPIO_ACTIVE_LOW>;
 			linux,input-type = <1>;
@@ -109,13 +106,6 @@
 	/* NXP PN547 NFC */
 };
 
-&blsp1_i2c4 {
-	status = "okay";
-	clock-frequency = <355000>;
-
-	/* Empty but active */
-};
-
 &blsp1_i2c6 {
 	status = "okay";
 	clock-frequency = <355000>;
@@ -195,26 +185,38 @@
 };
 
 &rpm_requests {
+	/* PMI8994 should probe first, because pmi8994_bby supplies some of PM8994's regulators */
+	pmi8994_regulators: pmi8994-regulators {
+		compatible = "qcom,rpm-pmi8994-regulators";
+
+		vdd_s1-supply = <&vph_pwr>;
+		vdd_bst_byp-supply = <&vph_pwr>;
+
+		pmi8994_s1: s1 {
+			regulator-min-microvolt = <1025000>;
+			regulator-max-microvolt = <1025000>;
+		};
+
+		/* S2 & S3 - VDD_GFX */
+
+		pmi8994_bby: boost-bypass {
+			regulator-min-microvolt = <3150000>;
+			regulator-max-microvolt = <3600000>;
+		};
+	};
+
 	pm8994_regulators: pm8994-regulators {
 		compatible = "qcom,rpm-pm8994-regulators";
 
-		vdd_s1-supply = <&vph_pwr>;
-		vdd_s2-supply = <&vph_pwr>;
 		vdd_s3-supply = <&vph_pwr>;
 		vdd_s4-supply = <&vph_pwr>;
 		vdd_s5-supply = <&vph_pwr>;
 		vdd_s6-supply = <&vph_pwr>;
 		vdd_s7-supply = <&vph_pwr>;
-		vdd_s8-supply = <&vph_pwr>;
-		vdd_s9-supply = <&vph_pwr>;
-		vdd_s10-supply = <&vph_pwr>;
-		vdd_s11-supply = <&vph_pwr>;
-		vdd_s12-supply = <&vph_pwr>;
 		vdd_l1-supply = <&pmi8994_s1>;
 		vdd_l2_l26_l28-supply = <&pm8994_s3>;
 		vdd_l3_l11-supply = <&pm8994_s3>;
 		vdd_l4_l27_l31-supply = <&pm8994_s3>;
-		vdd_l5_l7-supply = <&pm8994_s5>;
 		vdd_l6_l12_l32-supply = <&pm8994_s5>;
 		vdd_l8_l16_l30-supply = <&vph_pwr>;
 		vdd_l9_l10_l18_l22-supply = <&pmi8994_bby>;
@@ -223,7 +225,7 @@
 		vdd_l17_l29-supply = <&pmi8994_bby>;
 		vdd_l20_l21-supply = <&pmi8994_bby>;
 		vdd_l25-supply = <&pm8994_s3>;
-		vdd_lvs1_lvs2-supply = <&pm8994_s4>;
+		vdd_lvs1_2-supply = <&pm8994_s4>;
 
 		/* S1, S2, S6 and S12 are managed by RPMPD */
 
@@ -235,9 +237,9 @@
 		pm8994_s4: s4 {
 			regulator-min-microvolt = <1800000>;
 			regulator-max-microvolt = <1800000>;
+			regulator-system-load = <325000>;
 			regulator-allow-set-load;
 			regulator-always-on;
-			regulator-system-load = <325000>;
 		};
 
 		pm8994_s5: s5 {
@@ -263,13 +265,14 @@
 		pm8994_l2: l2 {
 			regulator-min-microvolt = <1250000>;
 			regulator-max-microvolt = <1250000>;
-			regulator-allow-set-load;
 			regulator-system-load = <10000>;
+			regulator-allow-set-load;
 		};
 
 		pm8994_l3: l3 {
 			regulator-min-microvolt = <1100000>;
 			regulator-max-microvolt = <1100000>;
+			regulator-boot-on;
 		};
 
 		pm8994_l4: l4 {
@@ -309,8 +312,8 @@
 		pm8994_l12: l12 {
 			regulator-min-microvolt = <1800000>;
 			regulator-max-microvolt = <1800000>;
-			regulator-allow-set-load;
 			regulator-system-load = <10000>;
+			regulator-allow-set-load;
 		};
 
 		pm8994_l13: l13 {
@@ -321,8 +324,9 @@
 		pm8994_l14: l14 {
 			regulator-min-microvolt = <1800000>;
 			regulator-max-microvolt = <1800000>;
-			regulator-allow-set-load;
 			regulator-system-load = <10000>;
+			regulator-allow-set-load;
+			regulator-boot-on;
 		};
 
 		pm8994_l15: l15 {
@@ -338,44 +342,47 @@
 		pm8994_l17: l17 {
 			regulator-min-microvolt = <2200000>;
 			regulator-max-microvolt = <2200000>;
+			regulator-boot-on;
 		};
 
 		pm8994_l18: l18 {
 			regulator-min-microvolt = <2850000>;
 			regulator-max-microvolt = <2850000>;
 			regulator-always-on;
+			regulator-boot-on;
 		};
 
 		pm8994_l19: l19 {
 			regulator-min-microvolt = <2850000>;
 			regulator-max-microvolt = <2850000>;
+			regulator-boot-on;
 		};
 
 		pm8994_l20: l20 {
 			regulator-min-microvolt = <2950000>;
 			regulator-max-microvolt = <2950000>;
-			regulator-always-on;
-			regulator-boot-on;
-			regulator-allow-set-load;
 			regulator-system-load = <570000>;
+			regulator-allow-set-load;
 		};
 
 		pm8994_l21: l21 {
 			regulator-min-microvolt = <2950000>;
 			regulator-max-microvolt = <2950000>;
-			regulator-always-on;
-			regulator-allow-set-load;
 			regulator-system-load = <800000>;
+			regulator-allow-set-load;
 		};
 
 		pm8994_l22: l22 {
 			regulator-min-microvolt = <3000000>;
 			regulator-max-microvolt = <3000000>;
+			regulator-boot-on;
 		};
 
 		pm8994_l23: l23 {
 			regulator-min-microvolt = <2800000>;
 			regulator-max-microvolt = <2800000>;
+			regulator-always-on;
+			regulator-boot-on;
 		};
 
 		pm8994_l24: l24 {
@@ -386,6 +393,7 @@
 		pm8994_l25: l25 {
 			regulator-min-microvolt = <1000000>;
 			regulator-max-microvolt = <1000000>;
+			regulator-boot-on;
 		};
 
 		pm8994_l26: l26 {
@@ -396,30 +404,33 @@
 		pm8994_l27: l27 {
 			regulator-min-microvolt = <1200000>;
 			regulator-max-microvolt = <1200000>;
+			regulator-boot-on;
 		};
 
 		pm8994_l28: l28 {
 			regulator-min-microvolt = <1000000>;
 			regulator-max-microvolt = <1000000>;
-			regulator-allow-set-load;
 			regulator-system-load = <10000>;
+			regulator-allow-set-load;
 		};
 
 		pm8994_l29: l29 {
 			regulator-min-microvolt = <2700000>;
 			regulator-max-microvolt = <2700000>;
+			regulator-boot-on;
 		};
 
 		pm8994_l30: l30 {
 			regulator-min-microvolt = <1800000>;
 			regulator-max-microvolt = <1800000>;
+			regulator-boot-on;
 		};
 
 		pm8994_l31: l31 {
 			regulator-min-microvolt = <1200000>;
 			regulator-max-microvolt = <1200000>;
-			regulator-allow-set-load;
 			regulator-system-load = <10000>;
+			regulator-allow-set-load;
 		};
 
 		pm8994_l32: l32 {
@@ -427,26 +438,11 @@
 			regulator-max-microvolt = <1800000>;
 		};
 
-		pm8994_lvs1: lvs1 {};
-		pm8994_lvs2: lvs2 {};
-	};
-
-	pmi8994_regulators: pmi8994-regulators {
-		compatible = "qcom,rpm-pmi8994-regulators";
-
-		vdd_s1-supply = <&vph_pwr>;
-		vdd_bst_byp-supply = <&vph_pwr>;
-
-		pmi8994_s1: s1 {
-			regulator-min-microvolt = <1025000>;
-			regulator-max-microvolt = <1025000>;
+		pm8994_lvs1: lvs1 {
+			regulator-boot-on;
 		};
-
-		/* S2 & S3 - VDD_GFX */
-
-		pmi8994_bby: boost-bypass {
-			regulator-min-microvolt = <3150000>;
-			regulator-max-microvolt = <3600000>;
+		pm8994_lvs2: lvs2 {
+			regulator-boot-on;
 		};
 	};
 };
@@ -475,7 +471,7 @@
 &sdhc2 {
 	status = "okay";
 
-	cd-gpios = <&tlmm 100 0>;
+	cd-gpios = <&tlmm 100 GPIO_ACTIVE_HIGH>;
 	vmmc-supply = <&pm8994_l21>;
 	vqmmc-supply = <&pm8994_l13>;
 };
diff --git a/arch/arm64/boot/dts/qcom/msm8994.dtsi b/arch/arm64/boot/dts/qcom/msm8994.dtsi
index 5a9a5ed0565f..ded5b7ceeaf9 100644
--- a/arch/arm64/boot/dts/qcom/msm8994.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8994.dtsi
@@ -4,6 +4,9 @@
 
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/clock/qcom,gcc-msm8994.h>
+#include <dt-bindings/clock/qcom,mmcc-msm8994.h>
+#include <dt-bindings/clock/qcom,rpmcc.h>
+#include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/power/qcom-rpmpd.h>
 
 / {
@@ -12,6 +15,11 @@
 	#address-cells = <2>;
 	#size-cells = <2>;
 
+	aliases {
+		mmc1 = &sdhc1;
+		mmc2 = &sdhc2;
+	};
+
 	chosen { };
 
 	clocks {
@@ -93,7 +101,7 @@
 		CPU6: cpu@102 {
 			device_type = "cpu";
 			compatible = "arm,cortex-a57";
-			reg = <0x0 0x101>;
+			reg = <0x0 0x102>;
 			enable-method = "psci";
 			next-level-cache = <&L2_1>;
 		};
@@ -101,7 +109,7 @@
 		CPU7: cpu@103 {
 			device_type = "cpu";
 			compatible = "arm,cortex-a57";
-			reg = <0x0 0x101>;
+			reg = <0x0 0x103>;
 			enable-method = "psci";
 			next-level-cache = <&L2_1>;
 		};
@@ -157,12 +165,6 @@
 		reg = <0 0x80000000 0 0>;
 	};
 
-	tcsr_mutex: hwlock {
-		compatible = "qcom,tcsr-mutex";
-		syscon = <&tcsr_mutex_regs 0 0x80>;
-		#hwlock-cells = <1>;
-	};
-
 	pmu {
 		compatible = "arm,cortex-a53-pmu";
 		interrupts = <GIC_PPI 7 (GIC_CPU_MASK_SIMPLE(4)| IRQ_TYPE_LEVEL_HIGH)>;
@@ -183,8 +185,8 @@
 			no-map;
 		};
 
-		cont_splash_mem: memory@3800000 {
-			reg = <0 0x03800000 0 0x2400000>;
+		cont_splash_mem: memory@3401000 {
+			reg = <0 0x03401000 0 0x2200000>;
 			no-map;
 		};
 
@@ -233,7 +235,6 @@
 			interrupts = <GIC_SPI 168 IRQ_TYPE_EDGE_RISING>;
 			qcom,ipc = <&apcs 8 0>;
 			qcom,smd-edge = <15>;
-			qcom,local-pid = <0>;
 			qcom,remote-pid = <6>;
 
 			rpm_requests: rpm-requests {
@@ -241,7 +242,7 @@
 				qcom,smd-channels = "rpm_requests";
 
 				rpmcc: rpmcc {
-					compatible = "qcom,rpmcc-msm8994";
+					compatible = "qcom,rpmcc-msm8994", "qcom,rpmcc";
 					#clock-cells = <1>;
 				};
 
@@ -354,6 +355,15 @@
 			#mbox-cells = <1>;
 		};
 
+		watchdog@f9017000 {
+			compatible = "qcom,apss-wdt-msm8994", "qcom,kpss-wdt";
+			reg = <0xf9017000 0x1000>;
+			interrupts = <GIC_SPI 3 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 4 IRQ_TYPE_EDGE_RISING>;
+			clocks = <&sleep_clk>;
+			timeout-sec = <10>;
+		};
+
 		timer@f9020000 {
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -413,7 +423,7 @@
 		};
 
 		usb3: usb@f92f8800 {
-			compatible = "qcom,msm8996-dwc3", "qcom,dwc3";
+			compatible = "qcom,msm8994-dwc3", "qcom,dwc3";
 			reg = <0xf92f8800 0x400>;
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -423,7 +433,10 @@
 				 <&gcc GCC_SYS_NOC_USB3_AXI_CLK>,
 				 <&gcc GCC_USB30_SLEEP_CLK>,
 				 <&gcc GCC_USB30_MOCK_UTMI_CLK>;
-			clock-names = "core", "iface", "sleep", "mock_utmi", "ref", "xo";
+			clock-names = "core",
+				      "iface",
+				      "sleep",
+				      "mock_utmi";
 
 			assigned-clocks = <&gcc GCC_USB30_MOCK_UTMI_CLK>,
 					  <&gcc GCC_USB30_MASTER_CLK>;
@@ -443,19 +456,19 @@
 			};
 		};
 
-		sdhc1: sdhci@f9824900 {
-			compatible = "qcom,sdhci-msm-v4";
+		sdhc1: mmc@f9824900 {
+			compatible = "qcom,msm8994-sdhci", "qcom,sdhci-msm-v4";
 			reg = <0xf9824900 0x1a0>, <0xf9824000 0x800>;
-			reg-names = "hc_mem", "core_mem";
+			reg-names = "hc", "core";
 
 			interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "hc_irq", "pwr_irq";
 
-			clocks = <&gcc GCC_SDCC1_APPS_CLK>,
-			         <&gcc GCC_SDCC1_AHB_CLK>,
+			clocks = <&gcc GCC_SDCC1_AHB_CLK>,
+				 <&gcc GCC_SDCC1_APPS_CLK>,
 				 <&xo_board>;
-			clock-names = "core", "iface", "xo";
+			clock-names = "iface", "core", "xo";
 
 			pinctrl-names = "default", "sleep";
 			pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on &sdc1_rclk_on>;
@@ -466,25 +479,25 @@
 			status = "disabled";
 		};
 
-		sdhc2: sdhci@f98a4900 {
-			compatible = "qcom,sdhci-msm-v4";
+		sdhc2: mmc@f98a4900 {
+			compatible = "qcom,msm8994-sdhci", "qcom,sdhci-msm-v4";
 			reg = <0xf98a4900 0x11c>, <0xf98a4000 0x800>;
-			reg-names = "hc_mem", "core_mem";
+			reg-names = "hc", "core";
 
 			interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>,
 				<GIC_SPI 221 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "hc_irq", "pwr_irq";
 
-			clocks = <&gcc GCC_SDCC2_APPS_CLK>,
-				<&gcc GCC_SDCC2_AHB_CLK>,
-				<&xo_board>;
-			clock-names = "core", "iface", "xo";
+			clocks = <&gcc GCC_SDCC2_AHB_CLK>,
+				 <&gcc GCC_SDCC2_APPS_CLK>,
+				 <&xo_board>;
+			clock-names = "iface", "core", "xo";
 
 			pinctrl-names = "default", "sleep";
 			pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on>;
 			pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off>;
 
-			cd-gpios = <&tlmm 100 0>;
+			cd-gpios = <&tlmm 100 GPIO_ACTIVE_HIGH>;
 			bus-width = <4>;
 			status = "disabled";
 		};
@@ -498,7 +511,7 @@
 			#dma-cells = <1>;
 			qcom,ee = <0>;
 			qcom,controlled-remotely;
-			num-channels = <18>;
+			num-channels = <24>;
 			qcom,num-ees = <4>;
 		};
 
@@ -519,9 +532,9 @@
 			compatible = "qcom,i2c-qup-v2.2.1";
 			reg = <0xf9923000 0x500>;
 			interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc GCC_BLSP1_AHB_CLK>,
-						<&gcc GCC_BLSP1_QUP1_I2C_APPS_CLK>;
-			clock-names = "iface", "core";
+			clocks = <&gcc GCC_BLSP1_QUP1_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
 			clock-frequency = <400000>;
 			dmas = <&blsp1_dma 12>, <&blsp1_dma 13>;
 			dma-names = "tx", "rx";
@@ -555,9 +568,9 @@
 			compatible = "qcom,i2c-qup-v2.2.1";
 			reg = <0xf9924000 0x500>;
 			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc GCC_BLSP1_AHB_CLK>,
-						<&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>;
-			clock-names = "iface", "core";
+			clocks = <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
 			clock-frequency = <400000>;
 			dmas = <&blsp1_dma 14>, <&blsp1_dma 15>;
 			dma-names = "tx", "rx";
@@ -575,9 +588,9 @@
 			compatible = "qcom,i2c-qup-v2.2.1";
 			reg = <0xf9926000 0x500>;
 			interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc GCC_BLSP1_AHB_CLK>,
-						<&gcc GCC_BLSP1_QUP4_I2C_APPS_CLK>;
-			clock-names = "iface", "core";
+			clocks = <&gcc GCC_BLSP1_QUP4_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
 			clock-frequency = <400000>;
 			dmas = <&blsp1_dma 18>, <&blsp1_dma 19>;
 			dma-names = "tx", "rx";
@@ -593,9 +606,9 @@
 			compatible = "qcom,i2c-qup-v2.2.1";
 			reg = <0xf9927000 0x500>;
 			interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc GCC_BLSP1_AHB_CLK>,
-						<&gcc GCC_BLSP1_QUP5_I2C_APPS_CLK>;
-			clock-names = "iface", "core";
+			clocks = <&gcc GCC_BLSP1_QUP5_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
 			clock-frequency = <400000>;
 			dmas = <&blsp2_dma 20>, <&blsp2_dma 21>;
 			dma-names = "tx", "rx";
@@ -611,9 +624,9 @@
 			compatible = "qcom,i2c-qup-v2.2.1";
 			reg = <0xf9928000 0x500>;
 			interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc GCC_BLSP1_AHB_CLK>,
-						<&gcc GCC_BLSP1_QUP6_I2C_APPS_CLK>;
-			clock-names = "iface", "core";
+			clocks = <&gcc GCC_BLSP1_QUP6_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
 			clock-frequency = <400000>;
 			dmas = <&blsp1_dma 22>, <&blsp1_dma 23>;
 			dma-names = "tx", "rx";
@@ -634,7 +647,7 @@
 			#dma-cells = <1>;
 			qcom,ee = <0>;
 			qcom,controlled-remotely;
-			num-channels = <18>;
+			num-channels = <24>;
 			qcom,num-ees = <4>;
 		};
 
@@ -657,9 +670,9 @@
 			compatible = "qcom,i2c-qup-v2.2.1";
 			reg = <0xf9963000 0x500>;
 			interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc GCC_BLSP2_AHB_CLK>,
-					<&gcc GCC_BLSP2_QUP1_I2C_APPS_CLK>;
-			clock-names = "iface", "core";
+			clocks = <&gcc GCC_BLSP2_QUP1_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP2_AHB_CLK>;
+			clock-names = "core", "iface";
 			clock-frequency = <400000>;
 			dmas = <&blsp2_dma 12>, <&blsp2_dma 13>;
 			dma-names = "tx", "rx";
@@ -693,9 +706,9 @@
 			compatible = "qcom,i2c-qup-v2.2.1";
 			reg = <0xf9967000 0x500>;
 			interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc GCC_BLSP2_AHB_CLK>,
-						<&gcc GCC_BLSP2_QUP5_I2C_APPS_CLK>;
-			clock-names = "iface", "core";
+			clocks = <&gcc GCC_BLSP2_QUP5_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP2_AHB_CLK>;
+			clock-names = "core", "iface";
 			clock-frequency = <355000>;
 			dmas = <&blsp2_dma 20>, <&blsp2_dma 21>;
 			dma-names = "tx", "rx";
@@ -713,6 +726,9 @@
 			#reset-cells = <1>;
 			#power-domain-cells = <1>;
 			reg = <0xfc400000 0x2000>;
+
+			clock-names = "xo", "sleep";
+			clocks = <&xo_board>, <&sleep_clk>;
 		};
 
 		rpm_msg_ram: sram@fc428000 {
@@ -741,9 +757,10 @@
 			#interrupt-cells = <4>;
 		};
 
-		tcsr_mutex_regs: syscon@fd484000 {
-			compatible = "syscon";
-			reg = <0xfd484000 0x2000>;
+		tcsr_mutex: hwlock@fd484000 {
+			compatible = "qcom,msm8994-tcsr-mutex", "qcom,tcsr-mutex";
+			reg = <0xfd484000 0x1000>;
+			#hwlock-cells = <1>;
 		};
 
 		tlmm: pinctrl@fd510000 {
@@ -1009,6 +1026,62 @@
 				drive-strength = <2>;
 			};
 		};
+
+		mmcc: clock-controller@fd8c0000 {
+			compatible = "qcom,mmcc-msm8994";
+			reg = <0xfd8c0000 0x5200>;
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+			#power-domain-cells = <1>;
+
+			clock-names = "xo",
+				      "gpll0",
+				      "mmssnoc_ahb",
+				      "oxili_gfx3d_clk_src",
+				      "dsi0pll",
+				      "dsi0pllbyte",
+				      "dsi1pll",
+				      "dsi1pllbyte",
+				      "hdmipll";
+			clocks = <&xo_board>,
+				 <&gcc GPLL0_OUT_MMSSCC>,
+				 <&rpmcc RPM_SMD_MMSSNOC_AHB_CLK>,
+				 <&rpmcc RPM_SMD_GFX3D_CLK_SRC>,
+				 <0>,
+				 <0>,
+				 <0>,
+				 <0>,
+				 <0>;
+
+			assigned-clocks = <&mmcc MMPLL0_PLL>,
+					  <&mmcc MMPLL1_PLL>,
+					  <&mmcc MMPLL3_PLL>,
+					  <&mmcc MMPLL4_PLL>,
+					  <&mmcc MMPLL5_PLL>;
+			assigned-clock-rates = <800000000>,
+					       <1167000000>,
+					       <1020000000>,
+					       <960000000>,
+					       <600000000>;
+		};
+
+		ocmem: sram@fdd00000 {
+			compatible = "qcom,msm8974-ocmem";
+			reg = <0xfdd00000 0x2000>,
+			      <0xfec00000 0x200000>;
+			reg-names = "ctrl", "mem";
+			ranges = <0 0xfec00000 0x200000>;
+			clocks = <&rpmcc RPM_SMD_OCMEMGX_CLK>,
+				 <&mmcc OCMEMCX_OCMEMNOC_CLK>;
+			clock-names = "core", "iface";
+
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			gmu_sram: gmu-sram@0 {
+				reg = <0x0 0x180000>;
+			};
+		};
 	};
 
 	timer: timer {
diff --git a/arch/arm64/boot/dts/qcom/msm8996-mtp.dts b/arch/arm64/boot/dts/qcom/msm8996-mtp.dts
index 7d9fc35bc7a0..596ad4c896f5 100644
--- a/arch/arm64/boot/dts/qcom/msm8996-mtp.dts
+++ b/arch/arm64/boot/dts/qcom/msm8996-mtp.dts
@@ -9,7 +9,7 @@
 
 / {
 	model = "Qualcomm Technologies, Inc. MSM 8996 MTP";
-	compatible = "qcom,msm8996-mtp";
+	compatible = "qcom,msm8996-mtp", "qcom,msm8996";
 
 	aliases {
 		serial0 = &blsp2_uart2;
@@ -18,12 +18,10 @@
 	chosen {
 		stdout-path = "serial0";
 	};
+};
 
-	soc {
-		serial@75b0000 {
-			status = "okay";
-		};
-	};
+&blsp2_uart2 {
+	status = "okay";
 };
 
 &hdmi {
diff --git a/arch/arm64/boot/dts/qcom/msm8996-pmi8996-sony-xperia-tone-dora.dts b/arch/arm64/boot/dts/qcom/msm8996-pmi8996-sony-xperia-tone-dora.dts
deleted file mode 100644
index b018693600a5..000000000000
--- a/arch/arm64/boot/dts/qcom/msm8996-pmi8996-sony-xperia-tone-dora.dts
+++ /dev/null
@@ -1,11 +0,0 @@
-// SPDX-License-Identifier: BSD-3-Clause
-/*
- * Copyright (c) 2021, Konrad Dybcio <konrad.dybcio@somainline.org>
- */
-
-#include "msm8996-sony-xperia-tone-dora.dts"
-#include "pmi8996.dtsi"
-
-/ {
-	model = "Sony Xperia X Performance (PMI8996)";
-};
diff --git a/arch/arm64/boot/dts/qcom/msm8996-pmi8996-sony-xperia-tone-kagura.dts b/arch/arm64/boot/dts/qcom/msm8996-pmi8996-sony-xperia-tone-kagura.dts
deleted file mode 100644
index 842ea3cf557e..000000000000
--- a/arch/arm64/boot/dts/qcom/msm8996-pmi8996-sony-xperia-tone-kagura.dts
+++ /dev/null
@@ -1,11 +0,0 @@
-// SPDX-License-Identifier: BSD-3-Clause
-/*
- * Copyright (c) 2021, Konrad Dybcio <konrad.dybcio@somainline.org>
- */
-
-#include "msm8996-sony-xperia-tone-kagura.dts"
-#include "pmi8996.dtsi"
-
-/ {
-	model = "Sony Xperia XZ (PMI8996)";
-};
diff --git a/arch/arm64/boot/dts/qcom/msm8996-pmi8996-sony-xperia-tone-keyaki.dts b/arch/arm64/boot/dts/qcom/msm8996-pmi8996-sony-xperia-tone-keyaki.dts
deleted file mode 100644
index b3f9062da4b0..000000000000
--- a/arch/arm64/boot/dts/qcom/msm8996-pmi8996-sony-xperia-tone-keyaki.dts
+++ /dev/null
@@ -1,11 +0,0 @@
-// SPDX-License-Identifier: BSD-3-Clause
-/*
- * Copyright (c) 2021, Konrad Dybcio <konrad.dybcio@somainline.org>
- */
-
-#include "msm8996-sony-xperia-tone-keyaki.dts"
-#include "pmi8996.dtsi"
-
-/ {
-	model = "Sony Xperia XZs (PMI8996)";
-};
diff --git a/arch/arm64/boot/dts/qcom/msm8996-sony-xperia-tone.dtsi b/arch/arm64/boot/dts/qcom/msm8996-sony-xperia-tone.dtsi
index ff7f39d29dd5..ca7c8d2e1d3d 100644
--- a/arch/arm64/boot/dts/qcom/msm8996-sony-xperia-tone.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8996-sony-xperia-tone.dtsi
@@ -8,18 +8,19 @@
 #include "msm8996.dtsi"
 #include "pm8994.dtsi"
 #include "pmi8994.dtsi"
+#include "pmi8996.dtsi"
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
 #include <dt-bindings/pinctrl/qcom,pmic-mpp.h>
 
-/delete-node/ &slpi_region;
-/delete-node/ &venus_region;
-/delete-node/ &zap_shader_region;
+/delete-node/ &adsp_mem;
+/delete-node/ &slpi_mem;
+/delete-node/ &venus_mem;
+/delete-node/ &gpu_mem;
 
 / {
 	qcom,msm-id = <246 0x30001>; /* MSM8996 V3.1 (Final) */
-	qcom,pmic-id = <0x20009 0x2000a 0 0>; /* PM8994 + PMI8994 */
 	qcom,board-id = <8 0>;
 
 	chosen {
@@ -41,23 +42,23 @@
 			ecc-size = <16>;
 		};
 
-		cont_splash_mem: memory@83401000 {
-			reg = <0 0x83401000 0 0x23ff000>;
+		adsp_mem: adsp@8ea00000 {
+			reg = <0x0 0x8ea00000 0x0 0x1a00000>;
 			no-map;
 		};
 
-		zap_shader_region: gpu@90400000 {
+		gpu_mem: gpu@90400000 {
 			compatible = "shared-dma-pool";
 			reg = <0x0 0x90400000 0x0 0x2000>;
 			no-map;
 		};
 
-		slpi_region: memory@90500000 {
+		slpi_mem: memory@90500000 {
 			reg = <0 0x90500000 0 0xa00000>;
 			no-map;
 		};
 
-		venus_region: memory@90f00000 {
+		venus_mem: memory@90f00000 {
 			reg = <0 0x90f00000 0 0x500000>;
 			no-map;
 		};
@@ -184,6 +185,7 @@
 &hsusb_phy1 {
 	status = "okay";
 
+	vdd-supply = <&pm8994_l28>;
 	vdda-pll-supply = <&pm8994_l12>;
 	vdda-phy-dpdm-supply = <&pm8994_l24>;
 };
@@ -194,8 +196,8 @@
 
 &pcie0 {
 	status = "okay";
-	perst-gpio = <&tlmm 35 GPIO_ACTIVE_LOW>;
-	wake-gpio = <&tlmm 37 GPIO_ACTIVE_HIGH>;
+	perst-gpios = <&tlmm 35 GPIO_ACTIVE_LOW>;
+	wake-gpios = <&tlmm 37 GPIO_ACTIVE_HIGH>;
 	vddpe-3v3-supply = <&wlan_en>;
 	vdda-supply = <&pm8994_l28>;
 };
@@ -240,14 +242,14 @@
 	 * probably a reason for it, and just to be on the safe side, we follow suit.
 	 */
 	pm8994_gpios_defaults: pm8994-gpios-default-state {
-		pm8994-gpio1-nc {
+		pm8994-gpio1-nc-pins {
 			pins = "gpio1";
 			function = PMIC_GPIO_FUNC_NORMAL;
 			drive-push-pull;
 			bias-high-impedance;
 		};
 
-		vol-down-n {
+		vol-down-n-pins {
 			pins = "gpio2";
 			function = PMIC_GPIO_FUNC_NORMAL;
 			drive-push-pull;
@@ -257,7 +259,7 @@
 			power-source = <PM8994_GPIO_S4>;
 		};
 
-		vol-up-n {
+		vol-up-n-pins {
 			pins = "gpio3";
 			function = PMIC_GPIO_FUNC_NORMAL;
 			drive-push-pull;
@@ -266,7 +268,7 @@
 			power-source = <PM8994_GPIO_S4>;
 		};
 
-		camera-snapshot-n {
+		camera-snapshot-n-pins {
 			pins = "gpio4";
 			function = PMIC_GPIO_FUNC_NORMAL;
 			drive-push-pull;
@@ -276,7 +278,7 @@
 			power-source = <PM8994_GPIO_S4>;
 		};
 
-		camera-focus-n {
+		camera-focus-n-pins {
 			pins = "gpio5";
 			function = PMIC_GPIO_FUNC_NORMAL;
 			drive-push-pull;
@@ -286,7 +288,7 @@
 			power-source = <PM8994_GPIO_S4>;
 		};
 
-		pm8994-gpio6-nc {
+		pm8994-gpio6-nc-pins {
 			pins = "gpio6";
 			function = PMIC_GPIO_FUNC_NORMAL;
 			drive-push-pull;
@@ -294,7 +296,7 @@
 			power-source = <PM8994_GPIO_VPH>;
 		};
 
-		nfc-download {
+		nfc-download-pins {
 			pins = "gpio7";
 			function = PMIC_GPIO_FUNC_NORMAL;
 			output-low;
@@ -304,7 +306,7 @@
 			power-source = <PM8994_GPIO_S4>;
 		};
 
-		pm8994-gpio8-nc {
+		pm8994-gpio8-nc-pins {
 			pins = "gpio8";
 			function = PMIC_GPIO_FUNC_NORMAL;
 			output-low;
@@ -314,7 +316,7 @@
 			power-source = <PM8994_GPIO_VPH>;
 		};
 
-		pm8994-gpio9-nc {
+		pm8994-gpio9-nc-pins {
 			pins = "gpio9";
 			function = PMIC_GPIO_FUNC_NORMAL;
 			output-high;
@@ -324,7 +326,7 @@
 			power-source = <PM8994_GPIO_VPH>;
 		};
 
-		nfc-clock {
+		nfc-clock-pins {
 			pins = "gpio10";
 			function = PMIC_GPIO_FUNC_NORMAL;
 			input-enable;
@@ -334,7 +336,7 @@
 			power-source = <PM8994_GPIO_S4>;
 		};
 
-		pm8994-gpio11-nc {
+		pm8994-gpio11-nc-pins {
 			pins = "gpio11";
 			function = PMIC_GPIO_FUNC_NORMAL;
 			drive-push-pull;
@@ -342,7 +344,7 @@
 			power-source = <PM8994_GPIO_VPH>;
 		};
 
-		pm8994-gpio12-nc {
+		pm8994-gpio12-nc-pins {
 			pins = "gpio12";
 			function = PMIC_GPIO_FUNC_NORMAL;
 			drive-push-pull;
@@ -350,7 +352,7 @@
 			power-source = <PM8994_GPIO_VPH>;
 		};
 
-		ear-enable {
+		ear-enable-pins {
 			pins = "gpio13";
 			function = PMIC_GPIO_FUNC_NORMAL;
 			output-high;
@@ -360,7 +362,7 @@
 			power-source = <PM8994_GPIO_S4>;
 		};
 
-		pm8994-gpio14-nc {
+		pm8994-gpio14-nc-pins {
 			pins = "gpio14";
 			function = PMIC_GPIO_FUNC_NORMAL;
 			drive-push-pull;
@@ -370,7 +372,7 @@
 			power-source = <PM8994_GPIO_VPH>;
 		};
 
-		pm-divclk1-gpio {
+		pm-divclk1-gpio-pins {
 			pins = "gpio15";
 			function = "func1";
 			output-high;
@@ -380,13 +382,13 @@
 			power-source = <PM8994_GPIO_VPH>;
 		};
 
-		pmi-clk-gpio {
+		pmi-clk-gpio-pins {
 			pins = "gpio16";
 			function = PMIC_GPIO_FUNC_NORMAL;
 			drive-push-pull;
 		};
 
-		pm8994-gpio17-nc {
+		pm8994-gpio17-nc-pins {
 			pins = "gpio17";
 			function = PMIC_GPIO_FUNC_NORMAL;
 			drive-push-pull;
@@ -394,7 +396,7 @@
 			power-source = <PM8994_GPIO_VPH>;
 		};
 
-		rome-sleep {
+		rome-sleep-pins {
 			pins = "gpio18";
 			function = PMIC_GPIO_FUNC_FUNC2;
 			output-low;
@@ -404,7 +406,7 @@
 			power-source = <PM8994_GPIO_S4>;
 		};
 
-		pm8994-gpio19-nc {
+		pm8994-gpio19-nc-pins {
 			pins = "gpio19";
 			function = PMIC_GPIO_FUNC_NORMAL;
 			output-low;
@@ -414,7 +416,7 @@
 			power-source = <PM8994_GPIO_VPH>;
 		};
 
-		pm8994-gpio22-nc {
+		pm8994-gpio22-nc-pins {
 			pins = "gpio22";
 			function = PMIC_GPIO_FUNC_NORMAL;
 			drive-push-pull;
@@ -439,34 +441,34 @@
 		"RF_ID";
 
 	pm8994_mpps_defaults: pm8994-mpps-default-state {
-		lcd-id_adc-mpp {
+		lcd-id_adc-mpp-pins {
 			pins = "mpp2";
 			function = "analog";
 			input-enable;
 			qcom,amux-route = <PMIC_MPP_AMUX_ROUTE_CH6>;
 		};
 
-		pm-mpp4-nc {
+		pm-mpp4-nc-pins {
 			pins = "mpp4";
 			function = "digital";
 			bias-high-impedance;
 			power-source = <PM8994_GPIO_VPH>;
 		};
 
-		flash-therm-mpp {
+		flash-therm-mpp-pins {
 			pins = "mpp5";
 			function = "analog";
 			input-enable;
 			qcom,amux-route = <PMIC_MPP_AMUX_ROUTE_CH5>;
 		};
 
-		mpp6-nc {
+		mpp6-nc-pins {
 			pins = "mpp6";
 			function = "digital";
 			bias-high-impedance;
 		};
 
-		rf-id-mpp {
+		rf-id-mpp-pins {
 			pins = "mpp8";
 			function = "analog";
 			input-enable;
@@ -497,7 +499,7 @@
 		"NC";
 
 	pmi8994_gpios_defaults: pmi8994-gpios-default-state {
-		vib-ldo-en-gpio {
+		vib-ldo-en-gpio-pins {
 			pins = "gpio1";
 			function = PMIC_GPIO_FUNC_NORMAL;
 			drive-push-pull;
@@ -506,7 +508,7 @@
 			power-source = <PM8994_GPIO_S4>;
 		};
 
-		pmi-gpio2-nc {
+		pmi-gpio2-nc-pins {
 			pins = "gpio2";
 			function = PMIC_GPIO_FUNC_NORMAL;
 			drive-push-pull;
@@ -516,7 +518,7 @@
 			power-source = <PM8994_GPIO_VPH>;
 		};
 
-		pmi-gpio3-nc {
+		pmi-gpio3-nc-pins {
 			pins = "gpio3";
 			function = PMIC_GPIO_FUNC_NORMAL;
 			drive-push-pull;
@@ -526,7 +528,7 @@
 			power-source = <PM8994_GPIO_VPH>;
 		};
 
-		pmi-gpio4-nc {
+		pmi-gpio4-nc-pins {
 			pins = "gpio4";
 			function = PMIC_GPIO_FUNC_NORMAL;
 			drive-push-pull;
@@ -535,7 +537,7 @@
 			power-source = <PM8994_GPIO_S4>;
 		};
 
-		pmi-gpio5-nc {
+		pmi-gpio5-nc-pins {
 			pins = "gpio5";
 			function = PMIC_GPIO_FUNC_NORMAL;
 			drive-push-pull;
@@ -544,7 +546,7 @@
 			power-source = <PM8994_GPIO_S4>;
 		};
 
-		pmi-gpio6-nc {
+		pmi-gpio6-nc-pins {
 			pins = "gpio6";
 			function = PMIC_GPIO_FUNC_NORMAL;
 			drive-push-pull;
@@ -553,7 +555,7 @@
 			power-source = <PM8994_GPIO_S4>;
 		};
 
-		pmi-gpio7-nc {
+		pmi-gpio7-nc-pins {
 			pins = "gpio7";
 			function = PMIC_GPIO_FUNC_NORMAL;
 			drive-push-pull;
@@ -562,7 +564,7 @@
 			power-source = <PM8994_GPIO_S4>;
 		};
 
-		pmi-gpio8-nc {
+		pmi-gpio8-nc-pins {
 			pins = "gpio8";
 			function = PMIC_GPIO_FUNC_NORMAL;
 			drive-push-pull;
@@ -571,13 +573,13 @@
 			power-source = <PM8994_GPIO_S4>;
 		};
 
-		usb-switch-sel {
+		usb-switch-sel-pins {
 			pins = "gpio9";
 			function = PMIC_GPIO_FUNC_NORMAL;
 			drive-push-pull;
 		};
 
-		pmi-gpio10-nc {
+		pmi-gpio10-nc-pins {
 			pins = "gpio10";
 			function = PMIC_GPIO_FUNC_NORMAL;
 			output-low;
@@ -589,34 +591,37 @@
 	};
 };
 
-&pmi8994_spmi_regulators {
+&pm8994_spmi_regulators {
 	qcom,saw-reg = <&saw3>;
 
-	vdd_gfx:
-	pmi8994_s2: s2 {
-		/* Pinned to a high value for now to avoid random crashes. */
-		regulator-min-microvolt = <1015000>;
-		regulator-max-microvolt = <1015000>;
-		regulator-name = "vdd_gfx";
-		regulator-always-on;
-	};
-
-	pmi8994_s9: s9 {
+	pm8994_s9: s9 {
 		qcom,saw-slave;
 	};
 
-	pmi8994_s10: s10 {
+	pm8994_s10: s10 {
 		qcom,saw-slave;
 	};
 
-	pmi8994_s11: s11 {
+	pm8994_s11: s11 {
 		qcom,saw-leader;
+		regulator-name = "vdd_apcc";
 		regulator-always-on;
 		regulator-min-microvolt = <470000>;
 		regulator-max-microvolt = <1140000>;
 	};
 };
 
+&pmi8994_spmi_regulators {
+	vdd_gfx:
+	pmi8994_s2: s2 {
+		/* Pinned to a high value for now to avoid random crashes. */
+		regulator-min-microvolt = <1015000>;
+		regulator-max-microvolt = <1015000>;
+		regulator-name = "vdd_gfx";
+		regulator-always-on;
+	};
+};
+
 &pmi8994_wled {
 	status = "okay";
 	default-brightness = <512>;
diff --git a/arch/arm64/boot/dts/qcom/msm8996-xiaomi-common.dtsi b/arch/arm64/boot/dts/qcom/msm8996-xiaomi-common.dtsi
index 01e573f0dfbf..77819186086a 100644
--- a/arch/arm64/boot/dts/qcom/msm8996-xiaomi-common.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8996-xiaomi-common.dtsi
@@ -38,10 +38,10 @@
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
-		vol_up {
+		key-vol-up {
 			label = "Volume Up";
 			gpios = <&pm8994_gpios 2 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_VOLUMEUP>;
@@ -49,7 +49,7 @@
 			debounce-interval = <15>;
 		};
 
-		dome {
+		key-dome {
 			label = "Home";
 			gpios = <&tlmm 34 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_HOME>;
@@ -58,6 +58,14 @@
 		};
 	};
 
+	irled {
+		compatible = "pwm-ir-tx";
+		pwms = <&pm8994_lpg 1 1000000>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&irled_default>;
+	};
+
 	reserved-memory {
 		memory@88800000 {
 			reg = <0x0 0x88800000 0x0 0x1400000>;
@@ -66,32 +74,32 @@
 
 		/* This platform has all PIL regions offset by 0x1400000 */
 		/delete-node/ mpss@88800000;
-		mpss_region: mpss@89c00000 {
+		mpss_mem: mpss@89c00000 {
 			reg = <0x0 0x89c00000 0x0 0x6200000>;
 			no-map;
 		};
 
 		/delete-node/ adsp@8ea00000;
-		adsp_region: adsp@8ea00000 {
+		adsp_mem: adsp@8fe00000 {
 			reg = <0x0 0x8fe00000 0x0 0x1b00000>;
 			no-map;
 		};
 
-		/delete-node/ slpi@90b00000;
-		slpi_region: slpi@91900000 {
+		/delete-node/ slpi@90500000;
+		slpi_mem: slpi@91900000 {
 			reg = <0x0 0x91900000 0x0 0xa00000>;
 			no-map;
 		};
 
-		/delete-node/ gpu@8f200000;
-		zap_shader_region: gpu@92300000 {
+		/delete-node/ gpu@90f00000;
+		gpu_mem: gpu@92300000 {
 			compatible = "shared-dma-pool";
 			reg = <0x0 0x92300000 0x0 0x2000>;
 			no-map;
 		};
 
 		/delete-node/ venus@91000000;
-		venus_region: venus@90400000 {
+		venus_mem: venus@92400000 {
 			reg = <0x0 0x92400000 0x0 0x500000>;
 			no-map;
 		};
@@ -107,7 +115,7 @@
 			pmsg-size = <0x40000>;
 		};
 
-		/delete-node/ rmtfs@86700000;
+		/delete-node/ rmtfs;
 		rmtfs@f6c00000 {
 			compatible = "qcom,rmtfs-mem";
 			reg = <0 0xf6c00000 0 0x200000>;
@@ -118,7 +126,7 @@
 		};
 
 		/delete-node/ mba@91500000;
-		mba_region: mba@f6f00000 {
+		mba_mem: mba@f6f00000 {
 			reg = <0x0 0xf6f00000 0x0 0x100000>;
 			no-map;
 		};
@@ -207,8 +215,8 @@
 	status = "okay";
 	label = "TYPEC_I2C";
 
-	typec: tusb320@47 {
-		compatible = "ti,tusb320";
+	typec: tusb320l@47 {
+		compatible = "ti,tusb320l";
 		reg = <0x47>;
 		interrupt-parent = <&tlmm>;
 		interrupts = <63 IRQ_TYPE_EDGE_RISING>;
@@ -267,6 +275,12 @@
 	vdd-gfx-supply = <&vdd_gfx>;
 };
 
+&mss_pil {
+	status = "okay";
+
+	pll-supply = <&vreg_l12a_1p8>;
+};
+
 &pcie0 {
 	status = "okay";
 
@@ -291,24 +305,65 @@
 	linux,code = <KEY_VOLUMEDOWN>;
 };
 
+&pm8994_lpg {
+	status = "okay";
+
+	qcom,power-source = <1>;
+};
+
+&pmi8994_lpg {
+	status = "okay";
+
+	qcom,power-source = <1>;
+
+	multi-led {
+		color = <LED_COLOR_ID_RGB>;
+		function = LED_FUNCTION_STATUS;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		led@1 {
+			reg = <1>;
+			color = <LED_COLOR_ID_BLUE>;
+		};
+
+		led@2 {
+			reg = <2>;
+			color = <LED_COLOR_ID_GREEN>;
+		};
+
+		led@3 {
+			reg = <3>;
+			color = <LED_COLOR_ID_RED>;
+		};
+	};
+};
+
+&slpi_pil {
+	status = "okay";
+
+	px-supply = <&vreg_lvs2a_1p8>;
+};
+
 &usb3 {
 	status = "okay";
 	extcon = <&typec>;
 
 	qcom,select-utmi-as-pipe-clk;
+};
 
-	dwc3@6a00000 {
-		extcon = <&typec>;
+&usb3_dwc3 {
+	extcon = <&typec>;
 
-		/* usb3-phy is not used on this device */
-		phys = <&hsusb_phy1>;
-		phy-names = "usb2-phy";
+	/* usb3-phy is not used on this device */
+	phys = <&hsusb_phy1>;
+	phy-names = "usb2-phy";
 
-		maximum-speed = "high-speed";
-		snps,is-utmi-l1-suspend;
-		snps,usb2-gadget-lpm-disable;
-		snps,hird-threshold = /bits/ 8 <0>;
-	};
+	maximum-speed = "high-speed";
+	snps,is-utmi-l1-suspend;
+	snps,usb2-gadget-lpm-disable;
+	snps,hird-threshold = /bits/ 8 <0>;
 };
 
 &hsusb_phy1 {
@@ -336,13 +391,7 @@
 
 	vdda-phy-supply = <&vreg_l28a_0p925>;
 	vdda-pll-supply = <&vreg_l12a_1p8>;
-
-	vdda-phy-max-microamp = <18380>;
-	vdda-pll-max-microamp = <9440>;
-
 	vddp-ref-clk-supply = <&vreg_l25a_1p2>;
-	vddp-ref-clk-max-microamp = <100>;
-	vddp-ref-clk-always-on;
 };
 
 &venus {
@@ -602,7 +651,16 @@
 };
 
 &pm8994_gpios {
-	wlan_en_default: wlan-en-default {
+	irled_default: irled-default-state {
+		pins = "gpio5";
+		function = PMIC_GPIO_FUNC_FUNC1;
+		output-low;
+		qcom,drive-strength = <PMIC_GPIO_STRENGTH_HIGH>;
+		power-source = <PM8994_GPIO_S4>;
+		bias-disable;
+	};
+
+	wlan_en_default: wlan-en-state {
 		pins = "gpio8";
 		function = PMIC_GPIO_FUNC_NORMAL;
 		output-low;
@@ -611,7 +669,7 @@
 		bias-disable;
 	};
 
-	rome_enable_default: rome-enable-default {
+	rome_enable_default: rome-enable-state {
 		pins = "gpio9";
 		function = PMIC_GPIO_FUNC_NORMAL;
 		output-high;
@@ -619,7 +677,7 @@
 		power-source = <PM8994_GPIO_VPH>;
 	};
 
-	divclk1_default: divclk1_default {
+	divclk1_default: divclk1-state {
 		pins = "gpio15";
 		function = PMIC_GPIO_FUNC_FUNC1;
 		bias-disable;
@@ -627,7 +685,7 @@
 		qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
 	};
 
-	divclk4_pin_a: divclk4 {
+	divclk4_pin_a: divclk4-state {
 		pins = "gpio18";
 		function = PMIC_GPIO_FUNC_FUNC2;
 		bias-disable;
diff --git a/arch/arm64/boot/dts/qcom/msm8996-xiaomi-gemini.dts b/arch/arm64/boot/dts/qcom/msm8996-xiaomi-gemini.dts
index 34f82e06ef53..4e5264f4116a 100644
--- a/arch/arm64/boot/dts/qcom/msm8996-xiaomi-gemini.dts
+++ b/arch/arm64/boot/dts/qcom/msm8996-xiaomi-gemini.dts
@@ -8,6 +8,7 @@
 #include "msm8996-xiaomi-common.dtsi"
 #include <dt-bindings/sound/qcom,q6afe.h>
 #include <dt-bindings/sound/qcom,q6asm.h>
+#include <dt-bindings/sound/qcom,wcd9335.h>
 #include <dt-bindings/input/ti-drv260x.h>
 
 / {
@@ -130,6 +131,11 @@
 	status = "okay";
 };
 
+&mss_pil {
+	firmware-name = "qcom/msm8996/gemini/mba.mbn",
+			"qcom/msm8996/gemini/modem.mbn";
+};
+
 &q6asmdai {
 	dai@0 {
 		reg = <0>;
@@ -144,10 +150,14 @@
 	};
 };
 
+&slpi_pil {
+	firmware-name = "qcom/msm8996/gemini/slpi.mbn";
+};
+
 &sound {
 	compatible = "qcom,apq8096-sndcard";
 	model = "gemini";
-	audio-routing =	"RX_BIAS", "MCLK",
+	audio-routing = "RX_BIAS", "MCLK",
 		"MM_DL1",  "MultiMedia1 Playback",
 		"MM_DL2",  "MultiMedia2 Playback",
 		"MultiMedia3 Capture", "MM_UL3";
@@ -184,7 +194,7 @@
 		};
 
 		codec {
-			sound-dai = <&wcd9335 6>;
+			sound-dai = <&wcd9335 AIF4_PB>;
 		};
 	};
 
@@ -199,7 +209,7 @@
 		};
 
 		codec {
-			sound-dai = <&wcd9335 1>;
+			sound-dai = <&wcd9335 AIF1_CAP>;
 		};
 	};
 };
@@ -248,7 +258,7 @@
 		"UIM_BATT_ALARM",	/* GPIO_21 */
 		"NC";			/* GPIO_22 */
 
-	divclk2_pin_a: divclk2 {
+	divclk2_pin_a: divclk2-state {
 		pins = "gpio16";
 		function = PMIC_GPIO_FUNC_FUNC2;
 		bias-disable;
diff --git a/arch/arm64/boot/dts/qcom/msm8996-xiaomi-natrium.dts b/arch/arm64/boot/dts/qcom/msm8996-xiaomi-natrium.dts
new file mode 100644
index 000000000000..ff4673ee9e81
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/msm8996-xiaomi-natrium.dts
@@ -0,0 +1,414 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2022, Alec Su <ae40515@yahoo.com.tw>
+ */
+
+/dts-v1/;
+
+#include "msm8996-xiaomi-common.dtsi"
+#include "pmi8996.dtsi"
+#include <dt-bindings/sound/qcom,q6afe.h>
+#include <dt-bindings/sound/qcom,q6asm.h>
+
+/ {
+	model = "Xiaomi Mi 5s Plus";
+	compatible = "xiaomi,natrium", "qcom,msm8996";
+	chassis-type = "handset";
+	qcom,msm-id = <305 0x10000>;
+	qcom,board-id = <47 0>;
+};
+
+&adsp_pil {
+	firmware-name = "qcom/msm8996/natrium/adsp.mbn";
+};
+
+&blsp2_i2c6 {
+	touchscreen@20 {
+		compatible = "syna,rmi4-i2c";
+		reg = <0x20>;
+		interrupt-parent = <&tlmm>;
+		interrupts = <125 IRQ_TYPE_LEVEL_LOW>;
+		vdd-supply = <&vdd_3v2_tp>;
+		syna,reset-delay-ms = <200>;
+		syna,startup-delay-ms = <5>;
+
+		pinctrl-names = "default", "sleep";
+		pinctrl-0 = <&touchscreen_default>;
+		pinctrl-1 = <&touchscreen_sleep>;
+	};
+};
+
+&dsi0 {
+	status = "okay";
+
+	vdda-supply = <&vreg_l2a_1p25>;
+	vcca-supply = <&vreg_l28a_0p925>;
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&mdss_dsi_default &mdss_te_default>;
+	pinctrl-1 = <&mdss_dsi_sleep &mdss_te_sleep>;
+
+	panel: panel@0 {
+		compatible = "jdi,fhd-r63452";
+		reg = <0>;
+		reset-gpios = <&tlmm 8 GPIO_ACTIVE_LOW>;
+		backlight = <&pmi8994_wled>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&dsi0_out>;
+			};
+		};
+	};
+};
+
+&dsi0_out {
+	remote-endpoint = <&panel_in>;
+};
+
+&gpu {
+	zap-shader {
+		firmware-name = "qcom/msm8996/natrium/a530_zap.mbn";
+	};
+};
+
+&mss_pil {
+	firmware-name = "qcom/msm8996/natrium/mba.mbn",
+			"qcom/msm8996/natrium/modem.mbn";
+};
+
+&pmi8994_wled {
+	status = "okay";
+
+	qcom,enabled-strings = <0 1>;
+	qcom,switching-freq = <600>;
+};
+
+&q6asmdai {
+	dai@0 {
+		reg = <0>;
+	};
+
+	dai@1 {
+		reg = <1>;
+	};
+
+	dai@2 {
+		reg = <2>;
+	};
+};
+
+&slpi_pil {
+	firmware-name = "qcom/msm8996/natrium/slpi.mbn";
+};
+
+&sound {
+	compatible = "qcom,apq8096-sndcard";
+	model = "natrium";
+	audio-routing =	"RX_BIAS", "MCLK";
+
+	mm1-dai-link {
+		link-name = "MultiMedia1";
+		cpu {
+			sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA1>;
+		};
+	};
+
+	mm2-dai-link {
+		link-name = "MultiMedia2";
+		cpu {
+			sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA2>;
+		};
+	};
+
+	mm3-dai-link {
+		link-name = "MultiMedia3";
+		cpu {
+			sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA3>;
+		};
+	};
+
+	slim-dai-link {
+		link-name = "SLIM Playback";
+		cpu {
+			sound-dai = <&q6afedai SLIMBUS_6_RX>;
+		};
+
+		platform {
+			sound-dai = <&q6routing>;
+		};
+
+		codec {
+			sound-dai = <&wcd9335 6>;
+		};
+	};
+
+	slimcap-dai-link {
+		link-name = "SLIM Capture";
+		cpu {
+			sound-dai = <&q6afedai SLIMBUS_0_TX>;
+		};
+
+		platform {
+			sound-dai = <&q6routing>;
+		};
+
+		codec {
+			sound-dai = <&wcd9335 1>;
+		};
+	};
+};
+
+&venus {
+	firmware-name = "qcom/msm8996/natrium/venus.mbn";
+};
+
+&rpm_requests {
+	pm8994-regulators {
+		vreg_l3a_0p875: l3 {
+			regulator-name = "vreg_l3a_0p875";
+			regulator-min-microvolt = <850000>;
+			regulator-max-microvolt = <1300000>;
+		};
+		vreg_l11a_1p1: l11 {
+			regulator-name = "vreg_l11a_1p1";
+			regulator-min-microvolt = <1100000>;
+			regulator-max-microvolt = <1100000>;
+		};
+		vreg_l17a_2p8: l17 {
+			regulator-name = "vreg_l17a_2p8";
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+		};
+		vreg_l18a_2p8: l18 {
+			regulator-name = "vreg_l18a_2p8";
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+		};
+		vreg_l29a_2p8: l29 {
+			regulator-name = "vreg_l29a_2p8";
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+		};
+	};
+};
+
+&pm8994_gpios {
+	gpio-line-names =
+		"NC",			/* GPIO_1  */
+		"VOL_UP_N",		/* GPIO_2  */
+		"SPKR_ID",		/* GPIO_3  */
+		"PWM_HAPTICS",		/* GPIO_4  */
+		"INFARED_DRV",		/* GPIO_5  */
+		"NC",			/* GPIO_6  */
+		"KEYPAD_LED_EN_A",	/* GPIO_7  */
+		"WL_EN",		/* GPIO_8  */
+		"3P3_ENABLE",		/* GPIO_9  */
+		"NC",			/* GPIO_10 */
+		"NC",			/* GPIO_11 */
+		"NC",			/* GPIO_12 */
+		"NC",			/* GPIO_13 */
+		"NC",			/* GPIO_14 */
+		"DIVCLK1_CDC",		/* GPIO_15 */
+		"DIVCLK2_HAPTICS",	/* GPIO_16 */
+		"NC",			/* GPIO_17 */
+		"32KHz_CLK_IN",		/* GPIO_18 */
+		"BT_EN",		/* GPIO_19 */
+		"PMIC_SLB",		/* GPIO_20 */
+		"UIM_BATT_ALARM",	/* GPIO_21 */
+		"NC";			/* GPIO_22 */
+};
+
+&pm8994_mpps {
+	gpio-line-names =
+		"NC",			/* MPP_1 */
+		"CCI_TIMER1",		/* MPP_2 */
+		"PMIC_SLB",		/* MPP_3 */
+		"EXT_FET_WLED_PWR_EN_N",/* MPP_4 */
+		"NC",			/* MPP_5 */
+		"NC",			/* MPP_6 */
+		"NC",			/* MPP_7 */
+		"NC";			/* MPP_8 */
+};
+
+&pmi8994_gpios {
+	gpio-line-names =
+		"NC",			/* GPIO_1  */
+		"SPKR_PA_EN",		/* GPIO_2  */
+		"NC",			/* GPIO_3  */
+		"NC",			/* GPIO_4  */
+		"NC",			/* GPIO_5  */
+		"NC",			/* GPIO_6  */
+		"NC",			/* GPIO_7  */
+		"NC",			/* GPIO_8  */
+		"NC",			/* GPIO_9  */
+		"NC";			/* GPIO_10 */
+};
+
+&tlmm {
+	gpio-line-names =
+		"ESE_SPI_MOSI",		/* GPIO_0   */
+		"ESE_SPI_MISO",		/* GPIO_1   */
+		"NC",			/* GPIO_2   */
+		"ESE_SPI_CLK",		/* GPIO_3   */
+		"MSM_UART_TX",		/* GPIO_4   */
+		"MSM_UART_RX",		/* GPIO_5   */
+		"NFC_I2C_SDA",		/* GPIO_6   */
+		"NFC_I2C_SCL",		/* GPIO_7   */
+		"LCD0_RESET_N",		/* GPIO_8   */
+		"NFC_IRQ",		/* GPIO_9   */
+		"LCD_TE",		/* GPIO_10  */
+		"LCD_ID_DET1",		/* GPIO_11  */
+		"NFC_DISABLE",		/* GPIO_12  */
+		"CAM_MCLK0",		/* GPIO_13  */
+		"CAM_MCLK1",		/* GPIO_14  */
+		"CAM_MCLK2",		/* GPIO_15  */
+		"ESE_PWR_REQ",		/* GPIO_16  */
+		"CCI_I2C_SDA0",		/* GPIO_17  */
+		"CCI_I2C_SCL0",		/* GPIO_18  */
+		"CCI_I2C_SDA1",		/* GPIO_19  */
+		"CCI_I2C_SCL1",		/* GPIO_20  */
+		"NFC_DWL_REQ",		/* GPIO_21  */
+		"CCI_TIMER1",		/* GPIO_22  */
+		"WEBCAM1_RESET_N",	/* GPIO_23  */
+		"ESE_IRQ",		/* GPIO_24  */
+		"NC",			/* GPIO_25  */
+		"WEBCAM1_STANDBY",	/* GPIO_26  */
+		"NC",			/* GPIO_27  */
+		"NC",			/* GPIO_28  */
+		"NC",			/* GPIO_29  */
+		"CAM_VDD_1P2_EN_2",	/* GPIO_30  */
+		"CAM_RESET_0",		/* GPIO_31  */
+		"CAM_RESET_1",		/* GPIO_32  */
+		"NC",			/* GPIO_33  */
+		"NC",			/* GPIO_34  */
+		"PCI_E0_RST_N",		/* GPIO_35  */
+		"PCI_E0_CLKREQ_N",	/* GPIO_36  */
+		"PCI_E0_WAKE",		/* GPIO_37  */
+		"CHARGER_INT",		/* GPIO_38  */
+		"CHARGER_RESET",	/* GPIO_39  */
+		"NC",			/* GPIO_40  */
+		"QCA_UART_TXD",		/* GPIO_41  */
+		"QCA_UART_RXD",		/* GPIO_42  */
+		"QCA_UART_CTS",		/* GPIO_43  */
+		"QCA_UART_RTS",		/* GPIO_44  */
+		"MAWC_UART_TX",		/* GPIO_45  */
+		"MAWC_UART_RX",		/* GPIO_46  */
+		"NC",			/* GPIO_47  */
+		"NC",			/* GPIO_48  */
+		"NC",			/* GPIO_49  */
+		"FP_SPI_RST",		/* GPIO_50  */
+		"TYPEC_I2C_SDA",	/* GPIO_51  */
+		"TYPEC_I2C_SCL",	/* GPIO_52  */
+		"CODEC_INT2_N",		/* GPIO_53  */
+		"CODEC_INT1_N",		/* GPIO_54  */
+		"APPS_I2C7_SDA",	/* GPIO_55  */
+		"APPS_I2C7_SCL",	/* GPIO_56  */
+		"FORCE_USB_BOOT",	/* GPIO_57  */
+		"NC",			/* GPIO_58  */
+		"NC",			/* GPIO_59  */
+		"NC",			/* GPIO_60  */
+		"NC",			/* GPIO_61  */
+		"ESE_RSTN",		/* GPIO_62  */
+		"TYPEC_INT",		/* GPIO_63  */
+		"CODEC_RESET_N",	/* GPIO_64  */
+		"PCM_CLK",		/* GPIO_65  */
+		"PCM_SYNC",		/* GPIO_66  */
+		"PCM_DIN",		/* GPIO_67  */
+		"PCM_DOUT",		/* GPIO_68  */
+		"CDC_44K1_CLK",		/* GPIO_69  */
+		"SLIMBUS_CLK",		/* GPIO_70  */
+		"SLIMBUS_DATA0",	/* GPIO_71  */
+		"SLIMBUS_DATA1",	/* GPIO_72  */
+		"LDO_5V_IN_EN",		/* GPIO_73  */
+		"TYPEC_EN_N",		/* GPIO_74  */
+		"NC",			/* GPIO_75  */
+		"NC",			/* GPIO_76  */
+		"NC",			/* GPIO_77  */
+		"NC",			/* GPIO_78  */
+		"NC",			/* GPIO_79  */
+		"SENSOR_RESET_N",	/* GPIO_80  */
+		"FP_SPI_MOSI",		/* GPIO_81  */
+		"FP_SPI_MISO",		/* GPIO_82  */
+		"FP_SPI_CS_N",		/* GPIO_83  */
+		"FP_SPI_CLK",		/* GPIO_84  */
+		"NC",			/* GPIO_85  */
+		"CAM_VDD_1P2_EN",	/* GPIO_86  */
+		"MSM_TS_I2C_SDA",	/* GPIO_87  */
+		"MSM_TS_I2C_SCL",	/* GPIO_88  */
+		"TS_RESOUT_N",		/* GPIO_89  */
+		"ESE_SPI_CS_N",		/* GPIO_90  */
+		"NC",			/* GPIO_91  */
+		"CAM2_AVDD_EN",		/* GPIO_92  */
+		"CAM2_VCM_EN",		/* GPIO_93  */
+		"NC",			/* GPIO_94  */
+		"NC",			/* GPIO_95  */
+		"NC",			/* GPIO_96  */
+		"GRFC_0",		/* GPIO_97  */
+		"GRFC_1",		/* GPIO_98  */
+		"NC",			/* GPIO_99  */
+		"GRFC_3",		/* GPIO_100 */
+		"GRFC_4",		/* GPIO_101 */
+		"GRFC_5",		/* GPIO_102 */
+		"NC",			/* GPIO_103 */
+		"GRFC_7",		/* GPIO_104 */
+		"UIM2_DATA",		/* GPIO_105 */
+		"UIM2_CLK",		/* GPIO_106 */
+		"UIM2_RESET",		/* GPIO_107 */
+		"UIM2_PRESENT",		/* GPIO_108 */
+		"UIM1_DATA",		/* GPIO_109 */
+		"UIM1_CLK",		/* GPIO_110 */
+		"UIM1_RESET",		/* GPIO_111 */
+		"UIM1_PRESENT",		/* GPIO_112 */
+		"UIM_BATT_ALARM",	/* GPIO_113 */
+		"GRFC_8",		/* GPIO_114 */
+		"GRFC_9",		/* GPIO_115 */
+		"TX_GTR_THRES",		/* GPIO_116 */
+		"ACCEL_INT",		/* GPIO_117 */
+		"GYRO_INT",		/* GPIO_118 */
+		"COMPASS_INT",		/* GPIO_119 */
+		"PROXIMITY_INT_N",	/* GPIO_120 */
+		"FP_IRQ",		/* GPIO_121 */
+		"P_SENSE",		/* GPIO_122 */
+		"HALL_INTR2",		/* GPIO_123 */
+		"HALL_INTR1",		/* GPIO_124 */
+		"TS_INT_N",		/* GPIO_125 */
+		"NC",			/* GPIO_126 */
+		"GRFC_11",		/* GPIO_127 */
+		"NC",			/* GPIO_128 */
+		"EXT_GPS_LNA_EN",	/* GPIO_129 */
+		"NC",			/* GPIO_130 */
+		"LCD_ID_DET2",		/* GPIO_131 */
+		"LCD_TE2",		/* GPIO_132 */
+		"GRFC_14",		/* GPIO_133 */
+		"GSM_TX2_PHASE_D",	/* GPIO_134 */
+		"NC",			/* GPIO_135 */
+		"GRFC_15",		/* GPIO_136 */
+		"RFFE3_DATA",		/* GPIO_137 */
+		"RFFE3_CLK",		/* GPIO_138 */
+		"NC",			/* GPIO_139 */
+		"NC",			/* GPIO_140 */
+		"RFFE5_DATA",		/* GPIO_141 */
+		"RFFE5_CLK",		/* GPIO_142 */
+		"NC",			/* GPIO_143 */
+		"COEX_UART_TX",		/* GPIO_144 */
+		"COEX_UART_RX",		/* GPIO_145 */
+		"RFFE2_DATA",		/* GPIO_146 */
+		"RFFE2_CLK",		/* GPIO_147 */
+		"RFFE1_DATA",		/* GPIO_148 */
+		"RFFE1_CLK";		/* GPIO_149 */
+
+	touchscreen_default: touchscreen-default {
+		pins = "gpio89", "gpio125";
+		function = "gpio";
+		drive-strength = <10>;
+		bias-pull-up;
+	};
+
+	touchscreen_sleep: touchscreen-sleep {
+		pins = "gpio89", "gpio125";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+};
diff --git a/arch/arm64/boot/dts/qcom/msm8996-xiaomi-scorpio.dts b/arch/arm64/boot/dts/qcom/msm8996-xiaomi-scorpio.dts
index e5b8402b1ed6..79be5fb1295b 100644
--- a/arch/arm64/boot/dts/qcom/msm8996-xiaomi-scorpio.dts
+++ b/arch/arm64/boot/dts/qcom/msm8996-xiaomi-scorpio.dts
@@ -9,6 +9,7 @@
 #include "pmi8996.dtsi"
 #include <dt-bindings/sound/qcom,q6afe.h>
 #include <dt-bindings/sound/qcom,q6asm.h>
+#include <dt-bindings/sound/qcom,wcd9335.h>
 
 / {
 	model = "Xiaomi Mi Note 2";
@@ -60,6 +61,20 @@
 };
 
 &blsp2_i2c6 {
+	touchkey: touchkey@28 {
+		compatible = "cypress,sf3155";
+		reg = <0x28>;
+		interrupt-parent = <&tlmm>;
+		interrupts = <77 IRQ_TYPE_EDGE_FALLING>;
+		avdd-supply = <&vreg_l6a_1p8>;
+		vdd-supply = <&vdd_3v2_tp>;
+		linux,keycodes = <KEY_BACK KEY_MENU>;
+
+		pinctrl-names = "default", "sleep";
+		pinctrl-0 = <&touchkey_default>;
+		pinctrl-1 = <&touchkey_sleep>;
+	};
+
 	touchscreen: atmel-mxt-ts@4a {
 		compatible = "atmel,maxtouch";
 		reg = <0x4a>;
@@ -97,6 +112,30 @@
 	status = "disabled";
 };
 
+&mss_pil {
+	firmware-name = "qcom/msm8996/scorpio/mba.mbn",
+			"qcom/msm8996/scorpio/modem.mbn";
+};
+
+&pm8994_lpg {
+	pinctrl-names = "default";
+	pinctrl-0 = <&keypad_default>;
+
+	led@3 {
+		reg = <3>;
+		color = <LED_COLOR_ID_WHITE>;
+		function = LED_FUNCTION_KBD_BACKLIGHT;
+		function-enumerator = <1>;
+	};
+
+	led@6 {
+		reg = <6>;
+		color = <LED_COLOR_ID_WHITE>;
+		function = LED_FUNCTION_KBD_BACKLIGHT;
+		function-enumerator = <0>;
+	};
+};
+
 &q6asmdai {
 	dai@0 {
 		reg = <0>;
@@ -111,10 +150,14 @@
 	};
 };
 
+&slpi_pil {
+	firmware-name = "qcom/msm8996/scorpio/slpi.mbn";
+};
+
 &sound {
 	compatible = "qcom,apq8096-sndcard";
 	model = "scorpio";
-	audio-routing =	"RX_BIAS", "MCLK";
+	audio-routing = "RX_BIAS", "MCLK";
 
 	mm1-dai-link {
 		link-name = "MultiMedia1";
@@ -148,7 +191,7 @@
 		};
 
 		codec {
-			sound-dai = <&wcd9335 6>;
+			sound-dai = <&wcd9335 AIF4_PB>;
 		};
 	};
 
@@ -163,7 +206,7 @@
 		};
 
 		codec {
-			sound-dai = <&wcd9335 1>;
+			sound-dai = <&wcd9335 AIF1_CAP>;
 		};
 	};
 };
@@ -235,6 +278,15 @@
 		"PMIC_SLB",		/* GPIO_20 */
 		"UIM_BATT_ALARM",	/* GPIO_21 */
 		"NC";			/* GPIO_22 */
+
+	keypad_default: keypad-default-state {
+		pins = "gpio7", "gpio10";
+		function = PMIC_GPIO_FUNC_FUNC1;
+		output-low;
+		qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
+		power-source = <PM8994_GPIO_S4>;
+		bias-disable;
+	};
 };
 
 &pm8994_mpps {
@@ -416,6 +468,20 @@
 		"RFFE1_DATA",		/* GPIO_148 */
 		"RFFE1_CLK";		/* GPIO_149 */
 
+	touchkey_default: touchkey_default {
+		pins = "gpio77";
+		function = "gpio";
+		drive-strength = <16>;
+		bias-pull-up;
+	};
+
+	touchkey_sleep: touchkey_sleep {
+		pins = "gpio77";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
 	touchscreen_default: touchscreen_default {
 		pins = "gpio75", "gpio125";
 		function = "gpio";
diff --git a/arch/arm64/boot/dts/qcom/msm8996.dtsi b/arch/arm64/boot/dts/qcom/msm8996.dtsi
index bccc2d0b35a8..c0a2baffa49d 100644
--- a/arch/arm64/boot/dts/qcom/msm8996.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8996.dtsi
@@ -6,6 +6,8 @@
 #include <dt-bindings/clock/qcom,gcc-msm8996.h>
 #include <dt-bindings/clock/qcom,mmcc-msm8996.h>
 #include <dt-bindings/clock/qcom,rpmcc.h>
+#include <dt-bindings/interconnect/qcom,msm8996.h>
+#include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/power/qcom-rpmpd.h>
 #include <dt-bindings/soc/qcom,apr.h>
 #include <dt-bindings/thermal/thermal.h>
@@ -134,7 +136,7 @@
 		};
 	};
 
-	cluster0_opp: opp_table0 {
+	cluster0_opp: opp-table-cluster0 {
 		compatible = "operating-points-v2-kryo-cpu";
 		nvmem-cells = <&speedbin_efuse>;
 		opp-shared;
@@ -222,7 +224,7 @@
 		};
 	};
 
-	cluster1_opp: opp_table1 {
+	cluster1_opp: opp-table-cluster1 {
 		compatible = "operating-points-v2-kryo-cpu";
 		nvmem-cells = <&speedbin_efuse>;
 		opp-shared;
@@ -357,17 +359,11 @@
 
 	firmware {
 		scm {
-			compatible = "qcom,scm-msm8996";
-			qcom,dload-mode = <&tcsr 0x13000>;
+			compatible = "qcom,scm-msm8996", "qcom,scm";
+			qcom,dload-mode = <&tcsr_2 0x13000>;
 		};
 	};
 
-	tcsr_mutex: hwlock {
-		compatible = "qcom,tcsr-mutex";
-		syscon = <&tcsr_mutex_regs 0 0x1000>;
-		#hwlock-cells = <1>;
-	};
-
 	memory@80000000 {
 		device_type = "memory";
 		/* We expect the bootloader to fill in the reg */
@@ -384,60 +380,65 @@
 		#size-cells = <2>;
 		ranges;
 
-		mba_region: mba@91500000 {
-			reg = <0x0 0x91500000 0x0 0x200000>;
+		hyp_mem: memory@85800000 {
+			reg = <0x0 0x85800000 0x0 0x600000>;
 			no-map;
 		};
 
-		slpi_region: slpi@90b00000 {
-			reg = <0x0 0x90b00000 0x0 0xa00000>;
+		xbl_mem: memory@85e00000 {
+			reg = <0x0 0x85e00000 0x0 0x200000>;
 			no-map;
 		};
 
-		venus_region: venus@90400000 {
-			reg = <0x0 0x90400000 0x0 0x700000>;
+		smem_mem: smem-mem@86000000 {
+			reg = <0x0 0x86000000 0x0 0x200000>;
 			no-map;
 		};
 
-		adsp_region: adsp@8ea00000 {
-			reg = <0x0 0x8ea00000 0x0 0x1a00000>;
+		tz_mem: memory@86200000 {
+			reg = <0x0 0x86200000 0x0 0x2600000>;
 			no-map;
 		};
 
-		mpss_region: mpss@88800000 {
-			reg = <0x0 0x88800000 0x0 0x6200000>;
+		rmtfs_mem: rmtfs {
+			compatible = "qcom,rmtfs-mem";
+
+			size = <0x0 0x200000>;
+			alloc-ranges = <0x0 0xa0000000 0x0 0x2000000>;
 			no-map;
+
+			qcom,client-id = <1>;
+			qcom,vmid = <15>;
 		};
 
-		smem_mem: smem-mem@86000000 {
-			reg = <0x0 0x86000000 0x0 0x200000>;
+		mpss_mem: mpss@88800000 {
+			reg = <0x0 0x88800000 0x0 0x6200000>;
 			no-map;
 		};
 
-		memory@85800000 {
-			reg = <0x0 0x85800000 0x0 0x800000>;
+		adsp_mem: adsp@8ea00000 {
+			reg = <0x0 0x8ea00000 0x0 0x1b00000>;
 			no-map;
 		};
 
-		memory@86200000 {
-			reg = <0x0 0x86200000 0x0 0x2600000>;
+		slpi_mem: slpi@90500000 {
+			reg = <0x0 0x90500000 0x0 0xa00000>;
 			no-map;
 		};
 
-		rmtfs@86700000 {
-			compatible = "qcom,rmtfs-mem";
-
-			size = <0x0 0x200000>;
-			alloc-ranges = <0x0 0xa0000000 0x0 0x2000000>;
+		gpu_mem: gpu@90f00000 {
+			compatible = "shared-dma-pool";
+			reg = <0x0 0x90f00000 0x0 0x100000>;
 			no-map;
+		};
 
-			qcom,client-id = <1>;
-			qcom,vmid = <15>;
+		venus_mem: venus@91000000 {
+			reg = <0x0 0x91000000 0x0 0x500000>;
+			no-map;
 		};
 
-		zap_shader_region: gpu@8f200000 {
-			compatible = "shared-dma-pool";
-			reg = <0x0 0x90b00000 0x0 0xa00000>;
+		mba_mem: mba@91500000 {
+			reg = <0x0 0x91500000 0x0 0x200000>;
 			no-map;
 		};
 	};
@@ -456,8 +457,10 @@
 			qcom,glink-channels = "rpm_requests";
 
 			rpmcc: qcom,rpmcc {
-				compatible = "qcom,rpmcc-msm8996";
+				compatible = "qcom,rpmcc-msm8996", "qcom,rpmcc";
 				#clock-cells = <1>;
+				clocks = <&xo_board>;
+				clock-names = "xo";
 			};
 
 			rpmpd: power-controller {
@@ -513,12 +516,12 @@
 		qcom,local-pid = <0>;
 		qcom,remote-pid = <2>;
 
-		smp2p_adsp_out: master-kernel {
+		adsp_smp2p_out: master-kernel {
 			qcom,entry-name = "master-kernel";
 			#qcom,smem-state-cells = <1>;
 		};
 
-		smp2p_adsp_in: slave-kernel {
+		adsp_smp2p_in: slave-kernel {
 			qcom,entry-name = "slave-kernel";
 
 			interrupt-controller;
@@ -526,7 +529,7 @@
 		};
 	};
 
-	smp2p-modem {
+	smp2p-mpss {
 		compatible = "qcom,smp2p";
 		qcom,smem = <435>, <428>;
 
@@ -537,12 +540,12 @@
 		qcom,local-pid = <0>;
 		qcom,remote-pid = <1>;
 
-		modem_smp2p_out: master-kernel {
+		mpss_smp2p_out: master-kernel {
 			qcom,entry-name = "master-kernel";
 			#qcom,smem-state-cells = <1>;
 		};
 
-		modem_smp2p_in: slave-kernel {
+		mpss_smp2p_in: slave-kernel {
 			qcom,entry-name = "slave-kernel";
 
 			interrupt-controller;
@@ -561,16 +564,17 @@
 		qcom,local-pid = <0>;
 		qcom,remote-pid = <3>;
 
-		smp2p_slpi_in: slave-kernel {
+		slpi_smp2p_out: master-kernel {
+			qcom,entry-name = "master-kernel";
+			#qcom,smem-state-cells = <1>;
+		};
+
+		slpi_smp2p_in: slave-kernel {
 			qcom,entry-name = "slave-kernel";
+
 			interrupt-controller;
 			#interrupt-cells = <2>;
 		};
-
-		smp2p_slpi_out: master-kernel {
-			qcom,entry-name = "master-kernel";
-			#qcom,smem-state-cells = <1>;
-		};
 	};
 
 	soc: soc {
@@ -579,12 +583,12 @@
 		ranges = <0 0 0 0xffffffff>;
 		compatible = "simple-bus";
 
-		pcie_phy: phy@34000 {
+		pcie_phy: phy-wrapper@34000 {
 			compatible = "qcom,msm8996-qmp-pcie-phy";
 			reg = <0x00034000 0x488>;
 			#address-cells = <1>;
 			#size-cells = <1>;
-			ranges;
+			ranges = <0x0 0x00034000 0x4000>;
 
 			clocks = <&gcc GCC_PCIE_PHY_AUX_CLK>,
 				<&gcc GCC_PCIE_PHY_CFG_AHB_CLK>,
@@ -595,46 +599,55 @@
 				<&gcc GCC_PCIE_PHY_COM_BCR>,
 				<&gcc GCC_PCIE_PHY_COM_NOCSR_BCR>;
 			reset-names = "phy", "common", "cfg";
+
 			status = "disabled";
 
-			pciephy_0: phy@35000 {
-				reg = <0x00035000 0x130>,
-				      <0x00035200 0x200>,
-				      <0x00035400 0x1dc>;
-				#phy-cells = <0>;
+			pciephy_0: phy@1000 {
+				reg = <0x1000 0x130>,
+				      <0x1200 0x200>,
+				      <0x1400 0x1dc>;
 
-				#clock-cells = <1>;
-				clock-output-names = "pcie_0_pipe_clk_src";
 				clocks = <&gcc GCC_PCIE_0_PIPE_CLK>;
 				clock-names = "pipe0";
 				resets = <&gcc GCC_PCIE_0_PHY_BCR>;
 				reset-names = "lane0";
-			};
 
-			pciephy_1: phy@36000 {
-				reg = <0x00036000 0x130>,
-				      <0x00036200 0x200>,
-				      <0x00036400 0x1dc>;
+				#clock-cells = <0>;
+				clock-output-names = "pcie_0_pipe_clk_src";
+
 				#phy-cells = <0>;
+			};
+
+			pciephy_1: phy@2000 {
+				reg = <0x2000 0x130>,
+				      <0x2200 0x200>,
+				      <0x2400 0x1dc>;
 
-				clock-output-names = "pcie_1_pipe_clk_src";
 				clocks = <&gcc GCC_PCIE_1_PIPE_CLK>;
 				clock-names = "pipe1";
 				resets = <&gcc GCC_PCIE_1_PHY_BCR>;
 				reset-names = "lane1";
-			};
 
-			pciephy_2: phy@37000 {
-				reg = <0x00037000 0x130>,
-				      <0x00037200 0x200>,
-				      <0x00037400 0x1dc>;
+				#clock-cells = <0>;
+				clock-output-names = "pcie_1_pipe_clk_src";
+
 				#phy-cells = <0>;
+			};
+
+			pciephy_2: phy@3000 {
+				reg = <0x3000 0x130>,
+				      <0x3200 0x200>,
+				      <0x3400 0x1dc>;
 
-				clock-output-names = "pcie_2_pipe_clk_src";
 				clocks = <&gcc GCC_PCIE_2_PIPE_CLK>;
 				clock-names = "pipe2";
 				resets = <&gcc GCC_PCIE_2_PHY_BCR>;
 				reset-names = "lane2";
+
+				#clock-cells = <0>;
+				clock-output-names = "pcie_2_pipe_clk_src";
+
+				#phy-cells = <0>;
 			};
 		};
 
@@ -644,7 +657,7 @@
 		};
 
 		qfprom@74000 {
-			compatible = "qcom,qfprom";
+			compatible = "qcom,msm8996-qfprom", "qcom,qfprom";
 			reg = <0x00074000 0x8ff>;
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -679,8 +692,33 @@
 			#power-domain-cells = <1>;
 			reg = <0x00300000 0x90000>;
 
-			clocks = <&rpmcc RPM_SMD_LN_BB_CLK>;
-			clock-names = "cxo2";
+			clocks = <&rpmcc RPM_SMD_BB_CLK1>,
+				 <&rpmcc RPM_SMD_LN_BB_CLK>,
+				 <&sleep_clk>,
+				 <&pciephy_0>,
+				 <&pciephy_1>,
+				 <&pciephy_2>,
+				 <&ssusb_phy_0>,
+				 <0>, <0>, <0>;
+			clock-names = "cxo",
+				      "cxo2",
+				      "sleep_clk",
+				      "pcie_0_pipe_clk_src",
+				      "pcie_1_pipe_clk_src",
+				      "pcie_2_pipe_clk_src",
+				      "usb3_phy_pipe_clk_src",
+				      "ufs_rx_symbol_0_clk_src",
+				      "ufs_rx_symbol_1_clk_src",
+				      "ufs_tx_symbol_0_clk_src";
+		};
+
+		bimc: interconnect@408000 {
+			compatible = "qcom,msm8996-bimc";
+			reg = <0x00408000 0x5a000>;
+			#interconnect-cells = <1>;
+			clock-names = "bus", "bus_a";
+			clocks = <&rpmcc RPM_SMD_BIMC_CLK>,
+				 <&rpmcc RPM_SMD_BIMC_A_CLK>;
 		};
 
 		tsens0: thermal-sensor@4a9000 {
@@ -705,7 +743,7 @@
 			#thermal-sensor-cells = <1>;
 		};
 
-		cryptobam: dma@644000 {
+		cryptobam: dma-controller@644000 {
 			compatible = "qcom,bam-v1.7.0";
 			reg = <0x00644000 0x24000>;
 			interrupts = <GIC_SPI 206 IRQ_TYPE_LEVEL_HIGH>;
@@ -713,7 +751,7 @@
 			clock-names = "bam_clk";
 			#dma-cells = <1>;
 			qcom,ee = <0>;
-			qcom,controlled-remotely = <1>;
+			qcom,controlled-remotely;
 		};
 
 		crypto: crypto@67a000 {
@@ -727,12 +765,86 @@
 			dma-names = "rx", "tx";
 		};
 
-		tcsr_mutex_regs: syscon@740000 {
-			compatible = "syscon";
-			reg = <0x00740000 0x40000>;
+		cnoc: interconnect@500000 {
+			compatible = "qcom,msm8996-cnoc";
+			reg = <0x00500000 0x1000>;
+			#interconnect-cells = <1>;
+			clock-names = "bus", "bus_a";
+			clocks = <&rpmcc RPM_SMD_CNOC_CLK>,
+				 <&rpmcc RPM_SMD_CNOC_A_CLK>;
+		};
+
+		snoc: interconnect@524000 {
+			compatible = "qcom,msm8996-snoc";
+			reg = <0x00524000 0x1c000>;
+			#interconnect-cells = <1>;
+			clock-names = "bus", "bus_a";
+			clocks = <&rpmcc RPM_SMD_SNOC_CLK>,
+				 <&rpmcc RPM_SMD_SNOC_A_CLK>;
+		};
+
+		a0noc: interconnect@543000 {
+			compatible = "qcom,msm8996-a0noc";
+			reg = <0x00543000 0x6000>;
+			#interconnect-cells = <1>;
+			clock-names = "aggre0_snoc_axi",
+				      "aggre0_cnoc_ahb",
+				      "aggre0_noc_mpu_cfg";
+			clocks = <&gcc GCC_AGGRE0_SNOC_AXI_CLK>,
+				 <&gcc GCC_AGGRE0_CNOC_AHB_CLK>,
+				 <&gcc GCC_AGGRE0_NOC_MPU_CFG_AHB_CLK>;
+			power-domains = <&gcc AGGRE0_NOC_GDSC>;
+		};
+
+		a1noc: interconnect@562000 {
+			compatible = "qcom,msm8996-a1noc";
+			reg = <0x00562000 0x5000>;
+			#interconnect-cells = <1>;
+			clock-names = "bus", "bus_a";
+			clocks = <&rpmcc RPM_SMD_AGGR1_NOC_CLK>,
+				 <&rpmcc RPM_SMD_AGGR1_NOC_A_CLK>;
+		};
+
+		a2noc: interconnect@583000 {
+			compatible = "qcom,msm8996-a2noc";
+			reg = <0x00583000 0x7000>;
+			#interconnect-cells = <1>;
+			clock-names = "bus", "bus_a";
+			clocks = <&rpmcc RPM_SMD_AGGR2_NOC_CLK>,
+				 <&rpmcc RPM_SMD_AGGR2_NOC_A_CLK>;
+		};
+
+		mnoc: interconnect@5a4000 {
+			compatible = "qcom,msm8996-mnoc";
+			reg = <0x005a4000 0x1c000>;
+			#interconnect-cells = <1>;
+			clock-names = "bus", "bus_a", "iface";
+			clocks = <&rpmcc RPM_SMD_MMAXI_CLK>,
+				 <&rpmcc RPM_SMD_MMAXI_A_CLK>,
+				 <&mmcc AHB_CLK_SRC>;
+		};
+
+		pnoc: interconnect@5c0000 {
+			compatible = "qcom,msm8996-pnoc";
+			reg = <0x005c0000 0x3000>;
+			#interconnect-cells = <1>;
+			clock-names = "bus", "bus_a";
+			clocks = <&rpmcc RPM_SMD_PCNOC_CLK>,
+				 <&rpmcc RPM_SMD_PCNOC_A_CLK>;
+		};
+
+		tcsr_mutex: hwlock@740000 {
+			compatible = "qcom,tcsr-mutex";
+			reg = <0x00740000 0x20000>;
+			#hwlock-cells = <1>;
 		};
 
-		tcsr: syscon@7a0000 {
+		tcsr_1: syscon@760000 {
+			compatible = "qcom,tcsr-msm8996", "syscon";
+			reg = <0x00760000 0x20000>;
+		};
+
+		tcsr_2: syscon@7a0000 {
 			compatible = "qcom,tcsr-msm8996", "syscon";
 			reg = <0x007a0000 0x18000>;
 		};
@@ -743,6 +855,22 @@
 			#reset-cells = <1>;
 			#power-domain-cells = <1>;
 			reg = <0x008c0000 0x40000>;
+			clocks = <&xo_board>,
+				 <&gcc GCC_MMSS_NOC_CFG_AHB_CLK>,
+				 <&gcc GPLL0>,
+				 <&dsi0_phy 1>,
+				 <&dsi0_phy 0>,
+				 <0>,
+				 <0>,
+				 <0>;
+			clock-names = "xo",
+				      "gcc_mmss_noc_cfg_ahb_clk",
+				      "gpll0",
+				      "dsi0pll",
+				      "dsi0pllbyte",
+				      "dsi1pll",
+				      "dsi1pllbyte",
+				      "hdmipll";
 			assigned-clocks = <&mmcc MMPLL9_PLL>,
 					  <&mmcc MMPLL1_PLL>,
 					  <&mmcc MMPLL3_PLL>,
@@ -771,8 +899,9 @@
 			interrupt-controller;
 			#interrupt-cells = <1>;
 
-			clocks = <&mmcc MDSS_AHB_CLK>;
-			clock-names = "iface";
+			clocks = <&mmcc MDSS_AHB_CLK>,
+				 <&mmcc MDSS_MDP_CLK>;
+			clock-names = "iface", "core";
 
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -786,7 +915,7 @@
 				reg-names = "mdp_phys";
 
 				interrupt-parent = <&mdss>;
-				interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
+				interrupts = <0>;
 
 				clocks = <&mmcc MDSS_AHB_CLK>,
 					 <&mmcc MDSS_AXI_CLK>,
@@ -806,6 +935,11 @@
 				assigned-clock-rates = <300000000>,
 					 <19200000>;
 
+				interconnects = <&mnoc MASTER_MDP_PORT0 &bimc SLAVE_EBI_CH0>,
+						<&mnoc MASTER_MDP_PORT1 &bimc SLAVE_EBI_CH0>,
+						<&mnoc MASTER_ROTATOR &bimc SLAVE_EBI_CH0>;
+				interconnect-names = "mdp0-mem", "mdp1-mem", "rotator-mem";
+
 				ports {
 					#address-cells = <1>;
 					#size-cells = <0>;
@@ -823,6 +957,13 @@
 							remote-endpoint = <&dsi0_in>;
 						};
 					};
+
+					port@2 {
+						reg = <2>;
+						mdp5_intf2_out: endpoint {
+							remote-endpoint = <&dsi1_in>;
+						};
+					};
 				};
 			};
 
@@ -832,7 +973,7 @@
 				reg-names = "dsi_ctrl";
 
 				interrupt-parent = <&mdss>;
-				interrupts = <4 IRQ_TYPE_LEVEL_HIGH>;
+				interrupts = <4>;
 
 				clocks = <&mmcc MDSS_MDP_CLK>,
 					 <&mmcc MDSS_BYTE0_CLK>,
@@ -848,6 +989,8 @@
 					      "core_mmss",
 					      "pixel",
 					      "core";
+				assigned-clocks = <&mmcc BYTE0_CLK_SRC>, <&mmcc PCLK0_CLK_SRC>;
+				assigned-clock-parents = <&dsi0_phy 0>, <&dsi0_phy 1>;
 
 				phys = <&dsi0_phy>;
 				phy-names = "dsi";
@@ -887,7 +1030,75 @@
 				#clock-cells = <1>;
 				#phy-cells = <0>;
 
-				clocks = <&mmcc MDSS_AHB_CLK>, <&xo_board>;
+				clocks = <&mmcc MDSS_AHB_CLK>, <&rpmcc RPM_SMD_BB_CLK1>;
+				clock-names = "iface", "ref";
+				status = "disabled";
+			};
+
+			dsi1: dsi@996000 {
+				compatible = "qcom,mdss-dsi-ctrl";
+				reg = <0x00996000 0x400>;
+				reg-names = "dsi_ctrl";
+
+				interrupt-parent = <&mdss>;
+				interrupts = <4>;
+
+				clocks = <&mmcc MDSS_MDP_CLK>,
+					 <&mmcc MDSS_BYTE1_CLK>,
+					 <&mmcc MDSS_AHB_CLK>,
+					 <&mmcc MDSS_AXI_CLK>,
+					 <&mmcc MMSS_MISC_AHB_CLK>,
+					 <&mmcc MDSS_PCLK1_CLK>,
+					 <&mmcc MDSS_ESC1_CLK>;
+				clock-names = "mdp_core",
+					      "byte",
+					      "iface",
+					      "bus",
+					      "core_mmss",
+					      "pixel",
+					      "core";
+				assigned-clocks = <&mmcc BYTE1_CLK_SRC>, <&mmcc PCLK1_CLK_SRC>;
+				assigned-clock-parents = <&dsi1_phy 0>, <&dsi1_phy 1>;
+
+				phys = <&dsi1_phy>;
+				phy-names = "dsi";
+				status = "disabled";
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+						dsi1_in: endpoint {
+							remote-endpoint = <&mdp5_intf2_out>;
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+						dsi1_out: endpoint {
+						};
+					};
+				};
+			};
+
+			dsi1_phy: dsi-phy@996400 {
+				compatible = "qcom,dsi-phy-14nm";
+				reg = <0x00996400 0x100>,
+				      <0x00996500 0x300>,
+				      <0x00996800 0x188>;
+				reg-names = "dsi_phy",
+					    "dsi_phy_lane",
+					    "dsi_pll";
+
+				#clock-cells = <1>;
+				#phy-cells = <0>;
+
+				clocks = <&mmcc MDSS_AHB_CLK>, <&rpmcc RPM_SMD_BB_CLK1>;
 				clock-names = "iface", "ref";
 				status = "disabled";
 			};
@@ -902,7 +1113,7 @@
 					    "hdcp_physical";
 
 				interrupt-parent = <&mdss>;
-				interrupts = <8 IRQ_TYPE_LEVEL_HIGH>;
+				interrupts = <8>;
 
 				clocks = <&mmcc MDSS_MDP_CLK>,
 					 <&mmcc MDSS_AHB_CLK>,
@@ -917,7 +1128,6 @@
 					"extp";
 
 				phys = <&hdmi_phy>;
-				phy-names = "hdmi_phy";
 				#sound-dai-cells = <1>;
 
 				status = "disabled";
@@ -952,9 +1162,13 @@
 					    "hdmi_phy";
 
 				clocks = <&mmcc MDSS_AHB_CLK>,
-					 <&gcc GCC_HDMI_CLKREF_CLK>;
+					 <&gcc GCC_HDMI_CLKREF_CLK>,
+					 <&xo_board>;
 				clock-names = "iface",
-					      "ref";
+					      "ref",
+					      "xo";
+
+				#clock-cells = <0>;
 
 				status = "disabled";
 			};
@@ -962,7 +1176,6 @@
 
 		gpu: gpu@b00000 {
 			compatible = "qcom,adreno-530.2", "qcom,adreno";
-			#stream-id-cells = <16>;
 
 			reg = <0x00b00000 0x3f000>;
 			reg-names = "kgsl_3d0_reg_memory";
@@ -981,15 +1194,15 @@
 				"mem",
 				"mem_iface";
 
+			interconnects = <&bimc MASTER_GRAPHICS_3D &bimc SLAVE_EBI_CH0>;
+			interconnect-names = "gfx-mem";
+
 			power-domains = <&mmcc GPU_GX_GDSC>;
 			iommus = <&adreno_smmu 0>;
 
 			nvmem-cells = <&speedbin_efuse>;
 			nvmem-cell-names = "speed_bin";
 
-			qcom,gpu-quirk-two-pass-use-wfi;
-			qcom,gpu-quirk-fault-detect-mask;
-
 			operating-points-v2 = <&gpu_opp_table>;
 
 			status = "disabled";
@@ -997,7 +1210,7 @@
 			#cooling-cells = <2>;
 
 			gpu_opp_table: opp-table {
-				compatible  ="operating-points-v2";
+				compatible = "operating-points-v2";
 
 				/*
 				 * 624Mhz and 560Mhz are only available on speed
@@ -1035,7 +1248,7 @@
 			};
 
 			zap-shader {
-				memory-region = <&zap_shader_region>;
+				memory-region = <&gpu_mem>;
 			};
 		};
 
@@ -1251,14 +1464,14 @@
 				pins = "gpio47", "gpio48";
 				function = "blsp_i2c3";
 				drive-strength = <16>;
-				bias-disable = <0>;
+				bias-disable;
 			};
 
 			blsp1_i2c3_sleep: blsp1-i2c2-sleep {
 				pins = "gpio47", "gpio48";
 				function = "gpio";
 				drive-strength = <2>;
-				bias-disable = <0>;
+				bias-disable;
 			};
 
 			blsp2_uart3_4pins_default: blsp2-uart2-4pins {
@@ -1550,7 +1763,7 @@
 			reg = <0x00290000 0x10000>;
 		};
 
-		spmi_bus: qcom,spmi@400f000 {
+		spmi_bus: spmi@400f000 {
 			compatible = "qcom,spmi-pmic-arb";
 			reg = <0x0400f000 0x1000>,
 			      <0x04400000 0x800000>,
@@ -1576,7 +1789,7 @@
 			ranges;
 
 			pcie0: pcie@600000 {
-				compatible = "qcom,pcie-msm8996", "snps,dw-pcie";
+				compatible = "qcom,pcie-msm8996";
 				status = "disabled";
 				power-domains = <&gcc PCIE0_GDSC>;
 				bus-range = <0x00 0xff>;
@@ -1619,7 +1832,7 @@
 					<&gcc GCC_PCIE_0_MSTR_AXI_CLK>,
 					<&gcc GCC_PCIE_0_SLV_AXI_CLK>;
 
-				clock-names =  "pipe",
+				clock-names = "pipe",
 						"aux",
 						"cfg",
 						"bus_master",
@@ -1628,12 +1841,12 @@
 			};
 
 			pcie1: pcie@608000 {
-				compatible = "qcom,pcie-msm8996", "snps,dw-pcie";
+				compatible = "qcom,pcie-msm8996";
 				power-domains = <&gcc PCIE1_GDSC>;
 				bus-range = <0x00 0xff>;
 				num-lanes = <1>;
 
-				status  = "disabled";
+				status = "disabled";
 
 				reg = <0x00608000 0x2000>,
 				      <0x0d000000 0xf1d>,
@@ -1673,7 +1886,7 @@
 					<&gcc GCC_PCIE_1_MSTR_AXI_CLK>,
 					<&gcc GCC_PCIE_1_SLV_AXI_CLK>;
 
-				clock-names =  "pipe",
+				clock-names = "pipe",
 						"aux",
 						"cfg",
 						"bus_master",
@@ -1681,7 +1894,7 @@
 			};
 
 			pcie2: pcie@610000 {
-				compatible = "qcom,pcie-msm8996", "snps,dw-pcie";
+				compatible = "qcom,pcie-msm8996";
 				power-domains = <&gcc PCIE2_GDSC>;
 				bus-range = <0x00 0xff>;
 				num-lanes = <1>;
@@ -1723,7 +1936,7 @@
 					<&gcc GCC_PCIE_2_MSTR_AXI_CLK>,
 					<&gcc GCC_PCIE_2_SLV_AXI_CLK>;
 
-				clock-names =  "pipe",
+				clock-names = "pipe",
 						"aux",
 						"cfg",
 						"bus_master",
@@ -1732,7 +1945,8 @@
 		};
 
 		ufshc: ufshc@624000 {
-			compatible = "qcom,ufshc";
+			compatible = "qcom,msm8996-ufshc", "qcom,ufshc",
+				     "jedec,ufs-2.0";
 			reg = <0x00624000 0x2500>;
 			interrupts = <GIC_SPI 265 IRQ_TYPE_LEVEL_HIGH>;
 
@@ -2008,6 +2222,9 @@
 				 <&mmcc VIDEO_AXI_CLK>,
 				 <&mmcc VIDEO_MAXI_CLK>;
 			clock-names = "core", "iface", "bus", "mbus";
+			interconnects = <&mnoc MASTER_VIDEO_P0 &bimc SLAVE_EBI_CH0>,
+					<&bimc MASTER_AMPSS_M0 &mnoc SLAVE_VENUS_CFG>;
+			interconnect-names = "video-mem", "cpu-cfg";
 			iommus = <&venus_smmu 0x00>,
 				 <&venus_smmu 0x01>,
 				 <&venus_smmu 0x0a>,
@@ -2028,7 +2245,7 @@
 				 <&venus_smmu 0x2c>,
 				 <&venus_smmu 0x2d>,
 				 <&venus_smmu 0x31>;
-			memory-region = <&venus_region>;
+			memory-region = <&venus_mem>;
 			status = "disabled";
 
 			video-decoder {
@@ -2124,6 +2341,105 @@
 			clock-names = "iface", "bus";
 		};
 
+		slpi_pil: remoteproc@1c00000 {
+			compatible = "qcom,msm8996-slpi-pil";
+			reg = <0x01c00000 0x4000>;
+
+			interrupts-extended = <&intc 0 390 IRQ_TYPE_EDGE_RISING>,
+					      <&slpi_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
+					      <&slpi_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
+					      <&slpi_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
+					      <&slpi_smp2p_in 3 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "wdog",
+					  "fatal",
+					  "ready",
+					  "handover",
+					  "stop-ack";
+
+			clocks = <&xo_board>,
+				 <&rpmcc RPM_SMD_AGGR2_NOC_CLK>;
+			clock-names = "xo", "aggre2";
+
+			memory-region = <&slpi_mem>;
+
+			qcom,smem-states = <&slpi_smp2p_out 0>;
+			qcom,smem-state-names = "stop";
+
+			power-domains = <&rpmpd MSM8996_VDDSSCX>;
+			power-domain-names = "ssc_cx";
+
+			status = "disabled";
+
+			smd-edge {
+				interrupts = <GIC_SPI 176 IRQ_TYPE_EDGE_RISING>;
+
+				label = "dsps";
+				mboxes = <&apcs_glb 25>;
+				qcom,smd-edge = <3>;
+				qcom,remote-pid = <3>;
+			};
+		};
+
+		mss_pil: remoteproc@2080000 {
+			compatible = "qcom,msm8996-mss-pil";
+			reg = <0x2080000 0x100>,
+			      <0x2180000 0x020>;
+			reg-names = "qdsp6", "rmb";
+
+			interrupts-extended = <&intc 0 448 IRQ_TYPE_EDGE_RISING>,
+					      <&mpss_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
+					      <&mpss_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
+					      <&mpss_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
+					      <&mpss_smp2p_in 3 IRQ_TYPE_EDGE_RISING>,
+					      <&mpss_smp2p_in 7 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "wdog", "fatal", "ready",
+					  "handover", "stop-ack",
+					  "shutdown-ack";
+
+			clocks = <&gcc GCC_MSS_CFG_AHB_CLK>,
+				 <&gcc GCC_MSS_Q6_BIMC_AXI_CLK>,
+				 <&gcc GCC_BOOT_ROM_AHB_CLK>,
+				 <&xo_board>,
+				 <&gcc GCC_MSS_GPLL0_DIV_CLK>,
+				 <&gcc GCC_MSS_SNOC_AXI_CLK>,
+				 <&gcc GCC_MSS_MNOC_BIMC_AXI_CLK>,
+				 <&rpmcc RPM_SMD_PCNOC_CLK>,
+				 <&rpmcc RPM_SMD_QDSS_CLK>;
+			clock-names = "iface", "bus", "mem", "xo", "gpll0_mss",
+				      "snoc_axi", "mnoc_axi", "pnoc", "qdss";
+
+			resets = <&gcc GCC_MSS_RESTART>;
+			reset-names = "mss_restart";
+
+			power-domains = <&rpmpd MSM8996_VDDCX>,
+					<&rpmpd MSM8996_VDDMX>;
+			power-domain-names = "cx", "mx";
+
+			qcom,smem-states = <&mpss_smp2p_out 0>;
+			qcom,smem-state-names = "stop";
+
+			qcom,halt-regs = <&tcsr_1 0x3000 0x5000 0x4000>;
+
+			status = "disabled";
+
+			mba {
+				memory-region = <&mba_mem>;
+			};
+
+			mpss {
+				memory-region = <&mpss_mem>;
+			};
+
+			smd-edge {
+				interrupts = <GIC_SPI 449 IRQ_TYPE_EDGE_RISING>;
+
+				label = "mpss";
+				mboxes = <&apcs_glb 12>;
+				qcom,smd-edge = <0>;
+				qcom,remote-pid = <1>;
+			};
+		};
+
 		stm@3002000 {
 			compatible = "arm,coresight-stm", "arm,primecell";
 			reg = <0x3002000 0x1000>,
@@ -2597,7 +2913,7 @@
 			reg = <0x06400000 0x90000>;
 
 			clock-names = "xo";
-			clocks = <&xo_board>;
+			clocks = <&rpmcc RPM_SMD_BB_CLK1>;
 
 			#clock-cells = <1>;
 		};
@@ -2614,20 +2930,28 @@
 			interrupt-names = "hs_phy_irq", "ss_phy_irq";
 
 			clocks = <&gcc GCC_SYS_NOC_USB3_AXI_CLK>,
-				<&gcc GCC_USB30_MASTER_CLK>,
-				<&gcc GCC_AGGRE2_USB3_AXI_CLK>,
-				<&gcc GCC_USB30_MOCK_UTMI_CLK>,
-				<&gcc GCC_USB30_SLEEP_CLK>,
-				<&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>;
+				 <&gcc GCC_USB30_MASTER_CLK>,
+				 <&gcc GCC_AGGRE2_USB3_AXI_CLK>,
+				 <&gcc GCC_USB30_SLEEP_CLK>,
+				 <&gcc GCC_USB30_MOCK_UTMI_CLK>;
+			clock-names = "cfg_noc",
+				      "core",
+				      "iface",
+				      "sleep",
+				      "mock_utmi";
 
 			assigned-clocks = <&gcc GCC_USB30_MOCK_UTMI_CLK>,
 					  <&gcc GCC_USB30_MASTER_CLK>;
 			assigned-clock-rates = <19200000>, <120000000>;
 
+			interconnects = <&a2noc MASTER_USB3 &bimc SLAVE_EBI_CH0>,
+					<&bimc MASTER_AMPSS_M0 &snoc SLAVE_USB3>;
+			interconnect-names = "usb-ddr", "apps-usb";
+
 			power-domains = <&gcc USB30_GDSC>;
 			status = "disabled";
 
-			usb3_dwc3: dwc3@6a00000 {
+			usb3_dwc3: usb@6a00000 {
 				compatible = "snps,dwc3";
 				reg = <0x06a00000 0xcc00>;
 				interrupts = <0 131 IRQ_TYPE_LEVEL_HIGH>;
@@ -2661,7 +2985,7 @@
 				      <0x07410600 0x1a8>;
 				#phy-cells = <0>;
 
-				#clock-cells = <1>;
+				#clock-cells = <0>;
 				clock-output-names = "usb3_phy_pipe_clk_src";
 				clocks = <&gcc GCC_USB3_PHY_PIPE_CLK>;
 				clock-names = "pipe0";
@@ -2696,10 +3020,10 @@
 			status = "disabled";
 		};
 
-		sdhc1: sdhci@7464900 {
-			compatible = "qcom,sdhci-msm-v4";
+		sdhc1: mmc@7464900 {
+			compatible = "qcom,msm8996-sdhci", "qcom,sdhci-msm-v4";
 			reg = <0x07464900 0x11c>, <0x07464000 0x800>;
-			reg-names = "hc_mem", "core_mem";
+			reg-names = "hc", "core";
 
 			interrupts = <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>,
 					<GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>;
@@ -2708,7 +3032,8 @@
 			clock-names = "iface", "core", "xo";
 			clocks = <&gcc GCC_SDCC1_AHB_CLK>,
 				<&gcc GCC_SDCC1_APPS_CLK>,
-				<&xo_board>;
+				<&rpmcc RPM_SMD_BB_CLK1>;
+			resets = <&gcc GCC_SDCC1_BCR>;
 
 			pinctrl-names = "default", "sleep";
 			pinctrl-0 = <&sdc1_state_on>;
@@ -2719,10 +3044,10 @@
 			status = "disabled";
 		};
 
-		sdhc2: sdhci@74a4900 {
-			compatible = "qcom,sdhci-msm-v4";
+		sdhc2: mmc@74a4900 {
+			compatible = "qcom,msm8996-sdhci", "qcom,sdhci-msm-v4";
 			reg = <0x074a4900 0x314>, <0x074a4000 0x800>;
-			reg-names = "hc_mem", "core_mem";
+			reg-names = "hc", "core";
 
 			interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>,
 				      <GIC_SPI 221 IRQ_TYPE_LEVEL_HIGH>;
@@ -2731,7 +3056,8 @@
 			clock-names = "iface", "core", "xo";
 			clocks = <&gcc GCC_SDCC2_AHB_CLK>,
 				<&gcc GCC_SDCC2_APPS_CLK>,
-				<&xo_board>;
+				<&rpmcc RPM_SMD_BB_CLK1>;
+			resets = <&gcc GCC_SDCC2_BCR>;
 
 			pinctrl-names = "default", "sleep";
 			pinctrl-0 = <&sdc2_state_on>;
@@ -2788,9 +3114,9 @@
 			compatible = "qcom,i2c-qup-v2.2.1";
 			reg = <0x07577000 0x1000>;
 			interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc GCC_BLSP1_AHB_CLK>,
-				<&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>;
-			clock-names = "iface", "core";
+			clocks = <&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
 			pinctrl-names = "default", "sleep";
 			pinctrl-0 = <&blsp1_i2c3_default>;
 			pinctrl-1 = <&blsp1_i2c3_sleep>;
@@ -2836,9 +3162,9 @@
 			compatible = "qcom,i2c-qup-v2.2.1";
 			reg = <0x075b5000 0x1000>;
 			interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc GCC_BLSP2_AHB_CLK>,
-				<&gcc GCC_BLSP2_QUP1_I2C_APPS_CLK>;
-			clock-names = "iface", "core";
+			clocks = <&gcc GCC_BLSP2_QUP1_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP2_AHB_CLK>;
+			clock-names = "core", "iface";
 			pinctrl-names = "default", "sleep";
 			pinctrl-0 = <&blsp2_i2c1_default>;
 			pinctrl-1 = <&blsp2_i2c1_sleep>;
@@ -2853,9 +3179,9 @@
 			compatible = "qcom,i2c-qup-v2.2.1";
 			reg = <0x075b6000 0x1000>;
 			interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc GCC_BLSP2_AHB_CLK>,
-				<&gcc GCC_BLSP2_QUP2_I2C_APPS_CLK>;
-			clock-names = "iface", "core";
+			clocks = <&gcc GCC_BLSP2_QUP2_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP2_AHB_CLK>;
+			clock-names = "core", "iface";
 			pinctrl-names = "default", "sleep";
 			pinctrl-0 = <&blsp2_i2c2_default>;
 			pinctrl-1 = <&blsp2_i2c2_sleep>;
@@ -2870,9 +3196,9 @@
 			compatible = "qcom,i2c-qup-v2.2.1";
 			reg = <0x075b7000 0x1000>;
 			interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc GCC_BLSP2_AHB_CLK>,
-				<&gcc GCC_BLSP2_QUP3_I2C_APPS_CLK>;
-			clock-names = "iface", "core";
+			clocks = <&gcc GCC_BLSP2_QUP3_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP2_AHB_CLK>;
+			clock-names = "core", "iface";
 			clock-frequency = <400000>;
 			pinctrl-names = "default", "sleep";
 			pinctrl-0 = <&blsp2_i2c3_default>;
@@ -2888,9 +3214,9 @@
 			compatible = "qcom,i2c-qup-v2.2.1";
 			reg = <0x75b9000 0x1000>;
 			interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc GCC_BLSP2_AHB_CLK>,
-				<&gcc GCC_BLSP2_QUP5_I2C_APPS_CLK>;
-			clock-names = "iface", "core";
+			clocks = <&gcc GCC_BLSP2_QUP5_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP2_AHB_CLK>;
+			clock-names = "core", "iface";
 			pinctrl-names = "default";
 			pinctrl-0 = <&blsp2_i2c5_default>;
 			dmas = <&blsp2_dma 20>, <&blsp2_dma 21>;
@@ -2904,9 +3230,9 @@
 			compatible = "qcom,i2c-qup-v2.2.1";
 			reg = <0x75ba000 0x1000>;
 			interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc GCC_BLSP2_AHB_CLK>,
-				<&gcc GCC_BLSP2_QUP6_I2C_APPS_CLK>;
-			clock-names = "iface", "core";
+			clocks = <&gcc GCC_BLSP2_QUP6_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP2_AHB_CLK>;
+			clock-names = "core", "iface";
 			pinctrl-names = "default", "sleep";
 			pinctrl-0 = <&blsp2_i2c6_default>;
 			pinctrl-1 = <&blsp2_i2c6_sleep>;
@@ -2946,6 +3272,11 @@
 				<&gcc GCC_USB20_MOCK_UTMI_CLK>,
 				<&gcc GCC_USB20_SLEEP_CLK>,
 				<&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>;
+			clock-names = "cfg_noc",
+				      "core",
+				      "iface",
+				      "sleep",
+				      "mock_utmi";
 
 			assigned-clocks = <&gcc GCC_USB20_MOCK_UTMI_CLK>,
 					  <&gcc GCC_USB20_MASTER_CLK>;
@@ -2955,7 +3286,7 @@
 			qcom,select-utmi-as-pipe-clk;
 			status = "disabled";
 
-			dwc3@7600000 {
+			usb2_dwc3: usb@7600000 {
 				compatible = "snps,dwc3";
 				reg = <0x07600000 0xcc00>;
 				interrupts = <0 138 IRQ_TYPE_LEVEL_HIGH>;
@@ -2971,7 +3302,7 @@
 			compatible = "qcom,bam-v1.7.0";
 			qcom,controlled-remotely;
 			reg = <0x09184000 0x32000>;
-			num-channels  = <31>;
+			num-channels = <31>;
 			interrupts = <0 164 IRQ_TYPE_LEVEL_HIGH>;
 			#dma-cells = <1>;
 			qcom,ee = <1>;
@@ -2983,7 +3314,7 @@
 			reg = <0x091c0000 0x2C000>;
 			reg-names = "ctrl";
 			interrupts = <0 163 IRQ_TYPE_LEVEL_HIGH>;
-			dmas =	<&slimbam 3>, <&slimbam 4>,
+			dmas = <&slimbam 3>, <&slimbam 4>,
 				<&slimbam 5>, <&slimbam 6>;
 			dma-names = "rx", "tx", "tx2", "rx2";
 			#address-cells = <1>;
@@ -2995,7 +3326,7 @@
 
 				tasha_ifd: tas-ifd {
 					compatible = "slim217,1a0";
-					reg  = <0 0>;
+					reg = <0 0>;
 				};
 
 				wcd9335: codec@1{
@@ -3003,17 +3334,17 @@
 					pinctrl-names = "default";
 
 					compatible = "slim217,1a0";
-					reg  = <1 0>;
+					reg = <1 0>;
 
 					interrupt-parent = <&tlmm>;
 					interrupts = <54 IRQ_TYPE_LEVEL_HIGH>,
 						     <53 IRQ_TYPE_LEVEL_HIGH>;
-					interrupt-names  = "intr1", "intr2";
+					interrupt-names = "intr1", "intr2";
 					interrupt-controller;
 					#interrupt-cells = <1>;
-					reset-gpios = <&tlmm 64 0>;
+					reset-gpios = <&tlmm 64 GPIO_ACTIVE_HIGH>;
 
-					slim-ifc-dev  = <&tasha_ifd>;
+					slim-ifc-dev = <&tasha_ifd>;
 
 					#sound-dai-cells = <1>;
 				};
@@ -3025,19 +3356,19 @@
 			reg = <0x09300000 0x80000>;
 
 			interrupts-extended = <&intc 0 162 IRQ_TYPE_EDGE_RISING>,
-					      <&smp2p_adsp_in 0 IRQ_TYPE_EDGE_RISING>,
-					      <&smp2p_adsp_in 1 IRQ_TYPE_EDGE_RISING>,
-					      <&smp2p_adsp_in 2 IRQ_TYPE_EDGE_RISING>,
-					      <&smp2p_adsp_in 3 IRQ_TYPE_EDGE_RISING>;
+					      <&adsp_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
+					      <&adsp_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
+					      <&adsp_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
+					      <&adsp_smp2p_in 3 IRQ_TYPE_EDGE_RISING>;
 			interrupt-names = "wdog", "fatal", "ready",
 					  "handover", "stop-ack";
 
-			clocks = <&xo_board>;
+			clocks = <&rpmcc RPM_SMD_BB_CLK1>;
 			clock-names = "xo";
 
-			memory-region = <&adsp_region>;
+			memory-region = <&adsp_mem>;
 
-			qcom,smem-states = <&smp2p_adsp_out 0>;
+			qcom,smem-states = <&adsp_smp2p_out 0>;
 			qcom,smem-state-names = "stop";
 
 			power-domains = <&rpmpd MSM8996_VDDCX>;
@@ -3058,7 +3389,7 @@
 					power-domains = <&gcc HLOS1_VOTE_LPASS_ADSP_GDSC>;
 					compatible = "qcom,apr-v2";
 					qcom,smd-channels = "apr_audio_svc";
-					qcom,apr-domain = <APR_DOMAIN_ADSP>;
+					qcom,domain = <APR_DOMAIN_ADSP>;
 					#address-cells = <1>;
 					#size-cells = <0>;
 
@@ -3173,7 +3504,7 @@
 		};
 
 		saw3: syscon@9a10000 {
-			compatible = "syscon";
+			compatible = "qcom,tcsr-msm8996", "syscon";
 			reg = <0x09a10000 0x1000>;
 		};
 
@@ -3277,7 +3608,7 @@
 			};
 		};
 
-		gpu-thermal-top {
+		gpu-top-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 
@@ -3299,7 +3630,7 @@
 			};
 		};
 
-		gpu-thermal-bottom {
+		gpu-bottom-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 
diff --git a/arch/arm64/boot/dts/qcom/msm8998-asus-novago-tp370ql.dts b/arch/arm64/boot/dts/qcom/msm8998-asus-novago-tp370ql.dts
index e204b7050441..102f3e9a79a1 100644
--- a/arch/arm64/boot/dts/qcom/msm8998-asus-novago-tp370ql.dts
+++ b/arch/arm64/boot/dts/qcom/msm8998-asus-novago-tp370ql.dts
@@ -16,20 +16,22 @@
 
 	touchpad@15 {
 		compatible = "hid-over-i2c";
-		interrupt-parent = <&tlmm>;
-		interrupts = <0x7b IRQ_TYPE_LEVEL_LOW>;
 		reg = <0x15>;
-		hid-descr-addr = <0x0001>;
-
 		pinctrl-names = "default";
 		pinctrl-0 = <&touchpad>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <123 IRQ_TYPE_LEVEL_LOW>;
+
+		hid-descr-addr = <0x0001>;
 	};
 
 	keyboard@3a {
 		compatible = "hid-over-i2c";
-		interrupt-parent = <&tlmm>;
-		interrupts = <0x25 IRQ_TYPE_LEVEL_LOW>;
 		reg = <0x3a>;
+		interrupt-parent = <&tlmm>;
+		interrupts = <37 IRQ_TYPE_LEVEL_LOW>;
+
 		hid-descr-addr = <0x0001>;
 	};
 };
@@ -37,12 +39,3 @@
 &sdhc2 {
 	cd-gpios = <&tlmm 95 GPIO_ACTIVE_HIGH>;
 };
-
-&tlmm {
-	touchpad: touchpad {
-		config {
-			pins = "gpio123";
-			bias-pull-up;
-		};
-	};
-};
diff --git a/arch/arm64/boot/dts/qcom/msm8998-clamshell.dtsi b/arch/arm64/boot/dts/qcom/msm8998-clamshell.dtsi
index 3f60575a351c..7928b8197474 100644
--- a/arch/arm64/boot/dts/qcom/msm8998-clamshell.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8998-clamshell.dtsi
@@ -8,13 +8,10 @@
  */
 
 #include "msm8998.dtsi"
-#include "pm8998.dtsi"
 #include "pm8005.dtsi"
+#include "pm8998.dtsi"
 
 / {
-	chosen {
-	};
-
 	vph_pwr: vph-pwr-regulator {
 		compatible = "regulator-fixed";
 		regulator-name = "vph_pwr";
@@ -37,6 +34,28 @@
 	};
 };
 
+&blsp1_uart3_on {
+	rx {
+		/delete-property/ bias-disable;
+		/*
+		 * Configure a pull-up on 45 (RX). This is needed to
+		 * avoid garbage data when the TX pin of the Bluetooth
+		 * module is in tri-state (module powered off or not
+		 * driving the signal yet).
+		 */
+		bias-pull-up;
+	};
+
+	cts {
+		/delete-property/ bias-disable;
+		/*
+		 * Configure a pull-down on 47 (CTS) to match the pull
+		 * of the Bluetooth module.
+		 */
+		bias-pull-down;
+	};
+};
+
 /*
  * The laptop FW does not appear to support the retention state as it is
  * not advertised as enabled in ACPI, and enabling it in DT can cause boot
@@ -74,6 +93,20 @@
 	cpu-idle-states = <&BIG_CPU_SLEEP_1>;
 };
 
+/*
+ * If EFIFB is used, enabling MMCC will cause important MMSS clocks to be cleaned
+ * up, because as far as Linux is concerned - they are unused. Disable it by default
+ * on clamshell devices, as it will break them, unless either simplefb is configured to
+ * hold a vote for these clocks, or panels are brought up properly, using drm/msm.
+ */
+&mmcc {
+	status = "disabled";
+};
+
+&mmss_smmu {
+	status = "disabled";
+};
+
 &pcie0 {
 	status = "okay";
 };
@@ -82,26 +115,23 @@
 	status = "okay";
 };
 
-&pm8005_lsid1 {
-	pm8005-regulators {
-		compatible = "qcom,pm8005-regulators";
+&pm8005_regulators {
+	vdd_s1-supply = <&vph_pwr>;
 
-		vdd_s1-supply = <&vph_pwr>;
+	pm8005_s1: s1 { /* VDD_GFX supply */
+		regulator-min-microvolt = <524000>;
+		regulator-max-microvolt = <1100000>;
+		regulator-enable-ramp-delay = <500>;
 
-		pm8005_s1: s1 { /* VDD_GFX supply */
-			regulator-min-microvolt = <524000>;
-			regulator-max-microvolt = <1100000>;
-			regulator-enable-ramp-delay = <500>;
-
-			/* hack until we rig up the gpu consumer */
-			regulator-always-on;
-		};
+		/* hack until we rig up the gpu consumer */
+		regulator-always-on;
 	};
 };
 
 &qusb2phy {
 	status = "okay";
 
+	vdd-supply = <&vreg_l1a_0p875>;
 	vdda-pll-supply = <&vreg_l12a_1p8>;
 	vdda-phy-dpdm-supply = <&vreg_l24a_3p075>;
 };
@@ -142,127 +172,156 @@
 			regulator-min-microvolt = <1352000>;
 			regulator-max-microvolt = <1352000>;
 		};
+
 		vreg_s4a_1p8: s4 {
 			regulator-min-microvolt = <1800000>;
 			regulator-max-microvolt = <1800000>;
 			regulator-allow-set-load;
 		};
+
 		vreg_s5a_2p04: s5 {
 			regulator-min-microvolt = <1904000>;
 			regulator-max-microvolt = <2040000>;
 		};
+
 		vreg_s7a_1p025: s7 {
 			regulator-min-microvolt = <900000>;
 			regulator-max-microvolt = <1028000>;
 		};
+
 		vreg_l1a_0p875: l1 {
 			regulator-min-microvolt = <880000>;
 			regulator-max-microvolt = <880000>;
 			regulator-allow-set-load;
 		};
+
 		vreg_l2a_1p2: l2 {
 			regulator-min-microvolt = <1200000>;
 			regulator-max-microvolt = <1200000>;
 			regulator-allow-set-load;
 		};
+
 		vreg_l3a_1p0: l3 {
 			regulator-min-microvolt = <1000000>;
 			regulator-max-microvolt = <1000000>;
 		};
+
 		vreg_l5a_0p8: l5 {
 			regulator-min-microvolt = <800000>;
 			regulator-max-microvolt = <800000>;
 		};
+
 		vreg_l6a_1p8: l6 {
 			regulator-min-microvolt = <1808000>;
 			regulator-max-microvolt = <1808000>;
 		};
+
 		vreg_l7a_1p8: l7 {
 			regulator-min-microvolt = <1800000>;
 			regulator-max-microvolt = <1800000>;
 			regulator-allow-set-load;
 		};
+
 		vreg_l8a_1p2: l8 {
 			regulator-min-microvolt = <1200000>;
 			regulator-max-microvolt = <1200000>;
 		};
+
 		vreg_l9a_1p8: l9 {
 			regulator-min-microvolt = <1808000>;
 			regulator-max-microvolt = <2960000>;
 		};
+
 		vreg_l10a_1p8: l10 {
 			regulator-min-microvolt = <1808000>;
 			regulator-max-microvolt = <2960000>;
 		};
+
 		vreg_l11a_1p0: l11 {
 			regulator-min-microvolt = <1000000>;
 			regulator-max-microvolt = <1000000>;
 		};
+
 		vreg_l12a_1p8: l12 {
 			regulator-min-microvolt = <1800000>;
 			regulator-max-microvolt = <1800000>;
 		};
+
 		vreg_l13a_2p95: l13 {
 			regulator-min-microvolt = <1808000>;
 			regulator-max-microvolt = <2960000>;
 		};
+
 		vreg_l14a_1p88: l14 {
 			regulator-min-microvolt = <1880000>;
 			regulator-max-microvolt = <1880000>;
 		};
+
 		vreg_l15a_1p8: l15 {
 			regulator-min-microvolt = <1800000>;
 			regulator-max-microvolt = <1800000>;
 		};
+
 		vreg_l16a_2p7: l16 {
 			regulator-min-microvolt = <2704000>;
 			regulator-max-microvolt = <2704000>;
 		};
+
 		vreg_l17a_1p3: l17 {
 			regulator-min-microvolt = <1304000>;
 			regulator-max-microvolt = <1304000>;
 			regulator-allow-set-load;
 		};
+
 		vreg_l18a_2p7: l18 {
 			regulator-min-microvolt = <2704000>;
 			regulator-max-microvolt = <2704000>;
 		};
+
 		vreg_l19a_3p0: l19 {
 			regulator-min-microvolt = <3008000>;
 			regulator-max-microvolt = <3008000>;
 		};
+
 		vreg_l20a_2p95: l20 {
 			regulator-min-microvolt = <2960000>;
 			regulator-max-microvolt = <2960000>;
 			regulator-allow-set-load;
 		};
+
 		vreg_l21a_2p95: l21 {
 			regulator-min-microvolt = <2960000>;
 			regulator-max-microvolt = <2960000>;
 			regulator-allow-set-load;
 			regulator-system-load = <800000>;
 		};
+
 		vreg_l22a_2p85: l22 {
 			regulator-min-microvolt = <2864000>;
 			regulator-max-microvolt = <2864000>;
 		};
+
 		vreg_l23a_3p3: l23 {
 			regulator-min-microvolt = <3312000>;
 			regulator-max-microvolt = <3312000>;
 		};
+
 		vreg_l24a_3p075: l24 {
 			regulator-min-microvolt = <3088000>;
 			regulator-max-microvolt = <3088000>;
 		};
+
 		vreg_l25a_3p3: l25 {
 			regulator-min-microvolt = <3104000>;
 			regulator-max-microvolt = <3312000>;
 			regulator-allow-set-load;
 		};
+
 		vreg_l26a_1p2: l26 {
 			regulator-min-microvolt = <1200000>;
 			regulator-max-microvolt = <1200000>;
 		};
+
 		vreg_l28_3p0: l28 {
 			regulator-min-microvolt = <3008000>;
 			regulator-max-microvolt = <3008000>;
@@ -277,7 +336,6 @@
 			regulator-min-microvolt = <1800000>;
 			regulator-max-microvolt = <1800000>;
 		};
-
 	};
 };
 
@@ -285,17 +343,6 @@
 	status = "okay";
 };
 
-&tlmm {
-	gpio-reserved-ranges = <0 4>, <81 4>;
-
-	touchpad: touchpad {
-		config {
-			pins = "gpio123";
-			bias-pull-up;           /* pull up */
-		};
-	};
-};
-
 &sdhc2 {
 	status = "okay";
 
@@ -303,8 +350,17 @@
 	vqmmc-supply = <&vreg_l13a_2p95>;
 
 	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&sdc2_clk_on  &sdc2_cmd_on  &sdc2_data_on  &sdc2_cd_on>;
-	pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdc2_cd_off>;
+	pinctrl-0 = <&sdc2_on &sdc2_cd>;
+	pinctrl-1 = <&sdc2_off &sdc2_cd>;
+};
+
+&tlmm {
+	gpio-reserved-ranges = <0 4>, <81 4>;
+
+	touchpad: touchpad-pin {
+		pins = "gpio123";
+		bias-pull-up;
+	};
 };
 
 &ufshc {
@@ -340,26 +396,3 @@
 	vdd-1.3-rfa-supply = <&vreg_l17a_1p3>;
 	vdd-3.3-ch0-supply = <&vreg_l25a_3p3>;
 };
-
-/* PINCTRL - board-specific pinctrl */
-&blsp1_uart3_on {
-	rx {
-		/delete-property/ bias-disable;
-		/*
-		 * Configure a pull-up on 45 (RX). This is needed to
-		 * avoid garbage data when the TX pin of the Bluetooth
-		 * module is in tri-state (module powered off or not
-		 * driving the signal yet).
-		 */
-		bias-pull-up;
-	};
-
-	cts {
-		/delete-property/ bias-disable;
-		/*
-		 * Configure a pull-down on 47 (CTS) to match the pull
-		 * of the Bluetooth module.
-		 */
-		bias-pull-down;
-	};
-};
diff --git a/arch/arm64/boot/dts/qcom/msm8998-fxtec-pro1.dts b/arch/arm64/boot/dts/qcom/msm8998-fxtec-pro1.dts
index 3d495ce3f46a..429ba57e20f7 100644
--- a/arch/arm64/boot/dts/qcom/msm8998-fxtec-pro1.dts
+++ b/arch/arm64/boot/dts/qcom/msm8998-fxtec-pro1.dts
@@ -6,11 +6,13 @@
 
 /dts-v1/;
 
-#include "msm8998-mtp.dtsi"
-
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/leds/common.h>
 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+#include "msm8998.dtsi"
+#include "pm8005.dtsi"
+#include "pm8998.dtsi"
+#include "pmi8998.dtsi"
 
 / {
 	model = "F(x)tec Pro1 (QX1000)";
@@ -18,6 +20,11 @@
 	chassis-type = "handset";
 	qcom,board-id = <0x02000b 0x10>;
 
+	aliases {
+		serial0 = &blsp2_uart1;
+		serial1 = &blsp1_uart3;
+	};
+
 	/*
 	 * Until we hook up type-c detection, we
 	 * have to stick with this. But it works.
@@ -29,12 +36,11 @@
 
 	gpio-hall-sensors {
 		compatible = "gpio-keys";
-		input-name = "hall-sensors";
 		label = "Hall sensors";
 		pinctrl-names = "default";
 		pinctrl-0 = <&hall_sensor1_default>;
 
-		hall-sensor1 {
+		event-hall-sensor1 {
 			label = "Keyboard Hall Sensor";
 			gpios = <&tlmm 124 GPIO_ACTIVE_HIGH>;
 			debounce-interval = <15>;
@@ -46,12 +52,11 @@
 
 	gpio-kb-extra-keys {
 		compatible = "gpio-keys";
-		input-name = "extra-kb-keys";
 		label = "Keyboard extra keys";
 		pinctrl-names = "default";
 		pinctrl-0 = <&gpio_kb_pins_extra>;
 
-		home {
+		key-home {
 			label = "Home";
 			gpios = <&tlmm 21 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_HOMEPAGE>;
@@ -59,7 +64,7 @@
 			linux,can-disable;
 		};
 
-		super-l {
+		key-super-l {
 			label = "Super Left";
 			gpios = <&tlmm 32 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_FN>;
@@ -67,7 +72,7 @@
 			linux,can-disable;
 		};
 
-		super-r {
+		key-super-r {
 			label = "Super Right";
 			gpios = <&tlmm 33 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_FN>;
@@ -75,7 +80,7 @@
 			linux,can-disable;
 		};
 
-		shift {
+		key-shift {
 			label = "Shift";
 			gpios = <&tlmm 114 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_RIGHTSHIFT>;
@@ -83,7 +88,7 @@
 			linux,can-disable;
 		};
 
-		ctrl {
+		key-ctrl {
 			label = "Ctrl";
 			gpios = <&tlmm 128 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_LEFTCTRL>;
@@ -91,7 +96,7 @@
 			linux,can-disable;
 		};
 
-		alt {
+		key-alt {
 			label = "Alt";
 			gpios = <&tlmm 129 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_LEFTALT>;
@@ -102,14 +107,11 @@
 
 	gpio-keys {
 		compatible = "gpio-keys";
-		input-name = "side-buttons";
 		label = "Side buttons";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&vol_up_pin_a>, <&cam_focus_pin_a>,
 			    <&cam_snapshot_pin_a>;
-		vol-up {
+		button-vol-up {
 			label = "Volume Up";
 			gpios = <&pm8998_gpio 6 GPIO_ACTIVE_LOW>;
 			linux,input-type = <EV_KEY>;
@@ -118,7 +120,7 @@
 			debounce-interval = <15>;
 		};
 
-		camera-snapshot {
+		button-camera-snapshot {
 			label = "Camera Snapshot";
 			gpios = <&pm8998_gpio 7 GPIO_ACTIVE_LOW>;
 			linux,input-type = <EV_KEY>;
@@ -126,7 +128,7 @@
 			debounce-interval = <15>;
 		};
 
-		camera-focus {
+		button-camera-focus {
 			label = "Camera Focus";
 			gpios = <&pm8998_gpio 8 GPIO_ACTIVE_LOW>;
 			linux,input-type = <EV_KEY>;
@@ -138,7 +140,7 @@
 	keyboard-leds {
 		compatible = "gpio-leds";
 
-		backlight {
+		led-0 {
 			color = <LED_COLOR_ID_WHITE>;
 			default-state = "off";
 			function = LED_FUNCTION_KBD_BACKLIGHT;
@@ -147,7 +149,7 @@
 			retain-state-suspended;
 		};
 
-		caps-lock {
+		led-1 {
 			color = <LED_COLOR_ID_YELLOW>;
 			default-state = "off";
 			function = LED_FUNCTION_CAPSLOCK;
@@ -190,10 +192,57 @@
 		pinctrl-0 = <&ts_vio_default>;
 		regulator-always-on;
 	};
+
+	vph_pwr: vph-pwr-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vph_pwr";
+		regulator-always-on;
+		regulator-boot-on;
+	};
+};
+
+&blsp1_uart3 {
+	status = "okay";
+
+	bluetooth {
+		compatible = "qcom,wcn3990-bt";
+
+		vddio-supply = <&vreg_s4a_1p8>;
+		vddxo-supply = <&vreg_l7a_1p8>;
+		vddrf-supply = <&vreg_l17a_1p3>;
+		vddch0-supply = <&vreg_l25a_3p3>;
+		max-speed = <3200000>;
+	};
+};
+
+&blsp1_uart3_on {
+	rx {
+		/delete-property/ bias-disable;
+		/*
+		 * Configure a pull-up on 45 (RX). This is needed to
+		 * avoid garbage data when the TX pin of the Bluetooth
+		 * module is in tri-state (module powered off or not
+		 * driving the signal yet).
+		 */
+		bias-pull-up;
+	};
+
+	cts {
+		/delete-property/ bias-disable;
+		/*
+		 * Configure a pull-down on 47 (CTS) to match the pull
+		 * of the Bluetooth module.
+		 */
+		bias-pull-down;
+	};
+};
+
+&blsp2_uart1 {
+	status = "okay";
 };
 
 &blsp2_i2c1 {
-	status = "ok";
+	status = "okay";
 
 	touchscreen@14 {
 		compatible = "goodix,gt9286";
@@ -208,16 +257,93 @@
 	};
 };
 
-&mmcc {
-	status = "ok";
+&etf {
+	status = "okay";
+};
+
+&etm1 {
+	status = "okay";
+};
+
+&etm2 {
+	status = "okay";
+};
+
+&etm3 {
+	status = "okay";
+};
+
+&etm4 {
+	status = "okay";
+};
+
+&etm5 {
+	status = "okay";
+};
+
+&etm6 {
+	status = "okay";
+};
+
+&etm7 {
+	status = "okay";
+};
+
+&etm8 {
+	status = "okay";
+};
+
+&etr {
+	status = "okay";
 };
 
-&mmss_smmu {
-	status = "ok";
+&funnel1 {
+	status = "okay";
+};
+
+&funnel2 {
+	status = "okay";
+};
+
+&funnel3 {
+	status = "okay";
+};
+
+&funnel4 {
+	// FIXME: Figure out why clock late_initcall crashes the board with
+	// this enabled.
+	// status = "okay";
+};
+
+&funnel5 {
+	// FIXME: Figure out why clock late_initcall crashes the board with
+	// this enabled.
+	// status = "okay";
+};
+
+&pcie0 {
+	status = "okay";
+};
+
+&pcie_phy {
+	status = "okay";
+};
+
+&pm8005_regulators {
+	vdd_s1-supply = <&vph_pwr>;
+
+	pm8005_s1: s1 { /* VDD_GFX supply */
+		regulator-min-microvolt = <524000>;
+		regulator-max-microvolt = <1100000>;
+		regulator-enable-ramp-delay = <500>;
+
+		/* Hack until we rig up the gpu consumer */
+		regulator-always-on;
+	};
 };
 
 &pm8998_gpio {
-	vol_up_pin_a: vol-up-active {
+	vol_up_pin_a: vol-up-active-state {
 		pins = "gpio6";
 		function = "normal";
 		bias-pull-up;
@@ -225,7 +351,7 @@
 		qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
 	};
 
-	cam_focus_pin_a: cam-focus-btn-active {
+	cam_focus_pin_a: cam-focus-btn-active-state {
 		pins = "gpio7";
 		function = "normal";
 		bias-pull-up;
@@ -233,7 +359,7 @@
 		qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
 	};
 
-	cam_snapshot_pin_a: cam-snapshot-btn-active {
+	cam_snapshot_pin_a: cam-snapshot-btn-active-state {
 		pins = "gpio8";
 		function = "normal";
 		bias-pull-up;
@@ -252,6 +378,240 @@
 	};
 };
 
+&qusb2phy {
+	status = "okay";
+
+	vdda-pll-supply = <&vreg_l12a_1p8>;
+	vdda-phy-dpdm-supply = <&vreg_l24a_3p075>;
+};
+
+&replicator1 {
+	status = "okay";
+};
+
+&rpm_requests {
+	pm8998-regulators {
+		compatible = "qcom,rpm-pm8998-regulators";
+
+		vdd_s1-supply = <&vph_pwr>;
+		vdd_s2-supply = <&vph_pwr>;
+		vdd_s3-supply = <&vph_pwr>;
+		vdd_s4-supply = <&vph_pwr>;
+		vdd_s5-supply = <&vph_pwr>;
+		vdd_s6-supply = <&vph_pwr>;
+		vdd_s7-supply = <&vph_pwr>;
+		vdd_s8-supply = <&vph_pwr>;
+		vdd_s9-supply = <&vph_pwr>;
+		vdd_s10-supply = <&vph_pwr>;
+		vdd_s11-supply = <&vph_pwr>;
+		vdd_s12-supply = <&vph_pwr>;
+		vdd_s13-supply = <&vph_pwr>;
+		vdd_l1_l27-supply = <&vreg_s7a_1p025>;
+		vdd_l2_l8_l17-supply = <&vreg_s3a_1p35>;
+		vdd_l3_l11-supply = <&vreg_s7a_1p025>;
+		vdd_l4_l5-supply = <&vreg_s7a_1p025>;
+		vdd_l6-supply = <&vreg_s5a_2p04>;
+		vdd_l7_l12_l14_l15-supply = <&vreg_s5a_2p04>;
+		vdd_l9-supply = <&vreg_bob>;
+		vdd_l10_l23_l25-supply = <&vreg_bob>;
+		vdd_l13_l19_l21-supply = <&vreg_bob>;
+		vdd_l16_l28-supply = <&vreg_bob>;
+		vdd_l18_l22-supply = <&vreg_bob>;
+		vdd_l20_l24-supply = <&vreg_bob>;
+		vdd_l26-supply = <&vreg_s3a_1p35>;
+		vdd_lvs1_lvs2-supply = <&vreg_s4a_1p8>;
+
+		vreg_s3a_1p35: s3 {
+			regulator-min-microvolt = <1352000>;
+			regulator-max-microvolt = <1352000>;
+		};
+
+		vreg_s4a_1p8: s4 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-allow-set-load;
+		};
+
+		vreg_s5a_2p04: s5 {
+			regulator-min-microvolt = <1904000>;
+			regulator-max-microvolt = <2040000>;
+		};
+
+		vreg_s7a_1p025: s7 {
+			regulator-min-microvolt = <900000>;
+			regulator-max-microvolt = <1028000>;
+		};
+
+		vreg_l1a_0p875: l1 {
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <880000>;
+		};
+
+		vreg_l2a_1p2: l2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		vreg_l3a_1p0: l3 {
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1000000>;
+		};
+
+		vreg_l5a_0p8: l5 {
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <800000>;
+		};
+
+		vreg_l6a_1p8: l6 {
+			regulator-min-microvolt = <1808000>;
+			regulator-max-microvolt = <1808000>;
+		};
+
+		vreg_l7a_1p8: l7 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		vreg_l8a_1p2: l8 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		vreg_l9a_1p8: l9 {
+			regulator-min-microvolt = <1808000>;
+			regulator-max-microvolt = <2960000>;
+		};
+
+		vreg_l10a_1p8: l10 {
+			regulator-min-microvolt = <1808000>;
+			regulator-max-microvolt = <2960000>;
+		};
+
+		vreg_l11a_1p0: l11 {
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1000000>;
+		};
+
+		vreg_l12a_1p8: l12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		vreg_l13a_2p95: l13 {
+			regulator-min-microvolt = <1808000>;
+			regulator-max-microvolt = <2960000>;
+		};
+
+		vreg_l14a_1p88: l14 {
+			regulator-min-microvolt = <1880000>;
+			regulator-max-microvolt = <1880000>;
+		};
+
+		vreg_l15a_1p8: l15 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		vreg_l16a_2p7: l16 {
+			regulator-min-microvolt = <2704000>;
+			regulator-max-microvolt = <2704000>;
+		};
+
+		vreg_l17a_1p3: l17 {
+			regulator-min-microvolt = <1304000>;
+			regulator-max-microvolt = <1304000>;
+		};
+
+		vreg_l18a_2p7: l18 {
+			regulator-min-microvolt = <2704000>;
+			regulator-max-microvolt = <2704000>;
+		};
+
+		vreg_l19a_3p0: l19 {
+			regulator-min-microvolt = <3008000>;
+			regulator-max-microvolt = <3008000>;
+		};
+
+		vreg_l20a_2p95: l20 {
+			regulator-min-microvolt = <2960000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l21a_2p95: l21 {
+			regulator-min-microvolt = <2960000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-system-load = <800000>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l22a_2p85: l22 {
+			regulator-min-microvolt = <2864000>;
+			regulator-max-microvolt = <2864000>;
+		};
+
+		vreg_l23a_3p3: l23 {
+			regulator-min-microvolt = <3312000>;
+			regulator-max-microvolt = <3312000>;
+		};
+
+		vreg_l24a_3p075: l24 {
+			regulator-min-microvolt = <3088000>;
+			regulator-max-microvolt = <3088000>;
+		};
+
+		vreg_l25a_3p3: l25 {
+			regulator-min-microvolt = <3104000>;
+			regulator-max-microvolt = <3312000>;
+		};
+
+		vreg_l26a_1p2: l26 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l28_3p0: l28 {
+			regulator-min-microvolt = <3008000>;
+			regulator-max-microvolt = <3008000>;
+		};
+
+		vreg_lvs1a_1p8: lvs1 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		vreg_lvs2a_1p8: lvs2 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+	};
+
+	pmi8998-regulators {
+		compatible = "qcom,rpm-pmi8998-regulators";
+
+		vdd_bob-supply = <&vph_pwr>;
+
+		vreg_bob: bob {
+			regulator-min-microvolt = <3312000>;
+			regulator-max-microvolt = <3600000>;
+		};
+	};
+};
+
+&remoteproc_adsp {
+	status = "okay";
+};
+
+&remoteproc_mss {
+	status = "okay";
+};
+
+&remoteproc_slpi {
+	status = "okay";
+};
+
 &tlmm {
 	gpio-reserved-ranges = <0 4>;
 
@@ -300,12 +660,41 @@
 	};
 };
 
+&sdhc2 {
+	status = "okay";
+	cd-gpios = <&tlmm 95 GPIO_ACTIVE_LOW>;
+
+	vmmc-supply = <&vreg_l21a_2p95>;
+	vqmmc-supply = <&vreg_l13a_2p95>;
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sdc2_on &sdc2_cd>;
+	pinctrl-1 = <&sdc2_off &sdc2_cd>;
+};
+
+&stm {
+	status = "okay";
+};
+
 &ufshc {
-	status = "ok";
+	status = "okay";
+	vcc-supply = <&vreg_l20a_2p95>;
+	vccq-supply = <&vreg_l26a_1p2>;
+	vccq2-supply = <&vreg_s4a_1p8>;
+	vcc-max-microamp = <750000>;
+	vccq-max-microamp = <560000>;
+	vccq2-max-microamp = <750000>;
 };
 
 &ufsphy {
-	status = "ok";
+	status = "okay";
+	vdda-phy-supply = <&vreg_l1a_0p875>;
+	vdda-pll-supply = <&vreg_l2a_1p2>;
+	vddp-ref-clk-supply = <&vreg_l26a_1p2>;
+};
+
+&usb3 {
+	status = "okay";
 };
 
 &usb3_dwc3 {
@@ -313,8 +702,24 @@
 	extcon = <&extcon_usb>;
 };
 
+&usb3phy {
+	status = "okay";
+
+	vdda-phy-supply = <&vreg_l1a_0p875>;
+	vdda-pll-supply = <&vreg_l2a_1p2>;
+};
+
 /* GT9286 analog supply */
 &vreg_l28_3p0 {
 	regulator-min-microvolt = <2800000>;
 	regulator-max-microvolt = <2800000>;
 };
+
+&wifi {
+	status = "okay";
+
+	vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>;
+	vdd-1.8-xo-supply = <&vreg_l7a_1p8>;
+	vdd-1.3-rfa-supply = <&vreg_l17a_1p3>;
+	vdd-3.3-ch0-supply = <&vreg_l25a_3p3>;
+};
diff --git a/arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dts b/arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dts
index 1eb406b43fd7..38389c6a3f68 100644
--- a/arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dts
+++ b/arch/arm64/boot/dts/qcom/msm8998-hp-envy-x2.dts
@@ -16,13 +16,14 @@
 
 	keyboard@3a {
 		compatible = "hid-over-i2c";
-		interrupt-parent = <&tlmm>;
-		interrupts = <0x79 IRQ_TYPE_LEVEL_LOW>;
 		reg = <0x3a>;
-		hid-descr-addr = <0x0001>;
-
 		pinctrl-names = "default";
 		pinctrl-0 = <&touchpad>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <121 IRQ_TYPE_LEVEL_LOW>;
+
+		hid-descr-addr = <0x0001>;
 	};
 };
 
diff --git a/arch/arm64/boot/dts/qcom/msm8998-lenovo-miix-630.dts b/arch/arm64/boot/dts/qcom/msm8998-lenovo-miix-630.dts
index f55f6f3e3e5d..cf81c33a9d7e 100644
--- a/arch/arm64/boot/dts/qcom/msm8998-lenovo-miix-630.dts
+++ b/arch/arm64/boot/dts/qcom/msm8998-lenovo-miix-630.dts
@@ -16,13 +16,14 @@
 
 	keyboard@3a {
 		compatible = "hid-over-i2c";
-		interrupt-parent = <&tlmm>;
-		interrupts = <0x79 IRQ_TYPE_LEVEL_LOW>;
 		reg = <0x3a>;
-		hid-descr-addr = <0x0001>;
-
 		pinctrl-names = "default";
 		pinctrl-0 = <&touchpad>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <121 IRQ_TYPE_LEVEL_LOW>;
+
+		hid-descr-addr = <0x0001>;
 	};
 };
 
diff --git a/arch/arm64/boot/dts/qcom/msm8998-mtp.dts b/arch/arm64/boot/dts/qcom/msm8998-mtp.dts
index 66540d2ca13b..a3ca58100aee 100644
--- a/arch/arm64/boot/dts/qcom/msm8998-mtp.dts
+++ b/arch/arm64/boot/dts/qcom/msm8998-mtp.dts
@@ -3,11 +3,450 @@
 
 /dts-v1/;
 
-#include "msm8998-mtp.dtsi"
+#include "msm8998.dtsi"
+#include "pm8005.dtsi"
+#include "pm8998.dtsi"
+#include "pmi8998.dtsi"
 
 / {
 	model = "Qualcomm Technologies, Inc. MSM8998 v1 MTP";
-	compatible = "qcom,msm8998-mtp";
+	compatible = "qcom,msm8998-mtp", "qcom,msm8998";
 
 	qcom,board-id = <8 0>;
+
+	aliases {
+		serial0 = &blsp2_uart1;
+		serial1 = &blsp1_uart3;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	vph_pwr: vph-pwr-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vph_pwr";
+		regulator-always-on;
+		regulator-boot-on;
+	};
+};
+
+&blsp1_uart3 {
+	status = "okay";
+
+	bluetooth {
+		compatible = "qcom,wcn3990-bt";
+
+		vddio-supply = <&vreg_s4a_1p8>;
+		vddxo-supply = <&vreg_l7a_1p8>;
+		vddrf-supply = <&vreg_l17a_1p3>;
+		vddch0-supply = <&vreg_l25a_3p3>;
+		max-speed = <3200000>;
+	};
+};
+
+&blsp1_uart3_on {
+	rx {
+		/delete-property/ bias-disable;
+		/*
+		 * Configure a pull-up on 45 (RX). This is needed to
+		 * avoid garbage data when the TX pin of the Bluetooth
+		 * module is in tri-state (module powered off or not
+		 * driving the signal yet).
+		 */
+		bias-pull-up;
+	};
+
+	cts {
+		/delete-property/ bias-disable;
+		/*
+		 * Configure a pull-down on 47 (CTS) to match the pull
+		 * of the Bluetooth module.
+		 */
+		bias-pull-down;
+	};
+};
+
+&blsp2_uart1 {
+	status = "okay";
+};
+
+&etf {
+	status = "okay";
+};
+
+&etm1 {
+	status = "okay";
+};
+
+&etm2 {
+	status = "okay";
+};
+
+&etm3 {
+	status = "okay";
+};
+
+&etm4 {
+	status = "okay";
+};
+
+&etm5 {
+	status = "okay";
+};
+
+&etm6 {
+	status = "okay";
+};
+
+&etm7 {
+	status = "okay";
+};
+
+&etm8 {
+	status = "okay";
+};
+
+&etr {
+	status = "okay";
+};
+
+&funnel1 {
+	status = "okay";
+};
+
+&funnel2 {
+	status = "okay";
+};
+
+&funnel3 {
+	status = "okay";
+};
+
+&funnel4 {
+	// FIXME: Figure out why clock late_initcall crashes the board with
+	// this enabled.
+	// status = "okay";
+};
+
+&funnel5 {
+	// FIXME: Figure out why clock late_initcall crashes the board with
+	// this enabled.
+	// status = "okay";
+};
+
+&pcie0 {
+	status = "okay";
+};
+
+&pcie_phy {
+	status = "okay";
+};
+
+&pm8005_regulators {
+	vdd_s1-supply = <&vph_pwr>;
+
+	pm8005_s1: s1 { /* VDD_GFX supply */
+		regulator-min-microvolt = <524000>;
+		regulator-max-microvolt = <1100000>;
+		regulator-enable-ramp-delay = <500>;
+
+		/* Hack until we rig up the gpu consumer */
+		regulator-always-on;
+	};
+};
+
+&qusb2phy {
+	status = "okay";
+
+	vdda-pll-supply = <&vreg_l12a_1p8>;
+	vdda-phy-dpdm-supply = <&vreg_l24a_3p075>;
+};
+
+&replicator1 {
+	status = "okay";
+};
+
+&rpm_requests {
+	pm8998-regulators {
+		compatible = "qcom,rpm-pm8998-regulators";
+
+		vdd_s1-supply = <&vph_pwr>;
+		vdd_s2-supply = <&vph_pwr>;
+		vdd_s3-supply = <&vph_pwr>;
+		vdd_s4-supply = <&vph_pwr>;
+		vdd_s5-supply = <&vph_pwr>;
+		vdd_s6-supply = <&vph_pwr>;
+		vdd_s7-supply = <&vph_pwr>;
+		vdd_s8-supply = <&vph_pwr>;
+		vdd_s9-supply = <&vph_pwr>;
+		vdd_s10-supply = <&vph_pwr>;
+		vdd_s11-supply = <&vph_pwr>;
+		vdd_s12-supply = <&vph_pwr>;
+		vdd_s13-supply = <&vph_pwr>;
+		vdd_l1_l27-supply = <&vreg_s7a_1p025>;
+		vdd_l2_l8_l17-supply = <&vreg_s3a_1p35>;
+		vdd_l3_l11-supply = <&vreg_s7a_1p025>;
+		vdd_l4_l5-supply = <&vreg_s7a_1p025>;
+		vdd_l6-supply = <&vreg_s5a_2p04>;
+		vdd_l7_l12_l14_l15-supply = <&vreg_s5a_2p04>;
+		vdd_l9-supply = <&vreg_bob>;
+		vdd_l10_l23_l25-supply = <&vreg_bob>;
+		vdd_l13_l19_l21-supply = <&vreg_bob>;
+		vdd_l16_l28-supply = <&vreg_bob>;
+		vdd_l18_l22-supply = <&vreg_bob>;
+		vdd_l20_l24-supply = <&vreg_bob>;
+		vdd_l26-supply = <&vreg_s3a_1p35>;
+		vdd_lvs1_lvs2-supply = <&vreg_s4a_1p8>;
+
+		vreg_s3a_1p35: s3 {
+			regulator-min-microvolt = <1352000>;
+			regulator-max-microvolt = <1352000>;
+		};
+
+		vreg_s4a_1p8: s4 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-allow-set-load;
+		};
+
+		vreg_s5a_2p04: s5 {
+			regulator-min-microvolt = <1904000>;
+			regulator-max-microvolt = <2040000>;
+		};
+
+		vreg_s7a_1p025: s7 {
+			regulator-min-microvolt = <900000>;
+			regulator-max-microvolt = <1028000>;
+		};
+
+		vreg_l1a_0p875: l1 {
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <880000>;
+		};
+
+		vreg_l2a_1p2: l2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		vreg_l3a_1p0: l3 {
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1000000>;
+		};
+
+		vreg_l5a_0p8: l5 {
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <800000>;
+		};
+
+		vreg_l6a_1p8: l6 {
+			regulator-min-microvolt = <1808000>;
+			regulator-max-microvolt = <1808000>;
+		};
+
+		vreg_l7a_1p8: l7 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		vreg_l8a_1p2: l8 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		vreg_l9a_1p8: l9 {
+			regulator-min-microvolt = <1808000>;
+			regulator-max-microvolt = <2960000>;
+		};
+
+		vreg_l10a_1p8: l10 {
+			regulator-min-microvolt = <1808000>;
+			regulator-max-microvolt = <2960000>;
+		};
+
+		vreg_l11a_1p0: l11 {
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1000000>;
+		};
+
+		vreg_l12a_1p8: l12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		vreg_l13a_2p95: l13 {
+			regulator-min-microvolt = <1808000>;
+			regulator-max-microvolt = <2960000>;
+		};
+
+		vreg_l14a_1p88: l14 {
+			regulator-min-microvolt = <1880000>;
+			regulator-max-microvolt = <1880000>;
+		};
+
+		vreg_l15a_1p8: l15 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		vreg_l16a_2p7: l16 {
+			regulator-min-microvolt = <2704000>;
+			regulator-max-microvolt = <2704000>;
+		};
+
+		vreg_l17a_1p3: l17 {
+			regulator-min-microvolt = <1304000>;
+			regulator-max-microvolt = <1304000>;
+		};
+
+		vreg_l18a_2p7: l18 {
+			regulator-min-microvolt = <2704000>;
+			regulator-max-microvolt = <2704000>;
+		};
+
+		vreg_l19a_3p0: l19 {
+			regulator-min-microvolt = <3008000>;
+			regulator-max-microvolt = <3008000>;
+		};
+
+		vreg_l20a_2p95: l20 {
+			regulator-min-microvolt = <2960000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l21a_2p95: l21 {
+			regulator-min-microvolt = <2960000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-system-load = <800000>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l22a_2p85: l22 {
+			regulator-min-microvolt = <2864000>;
+			regulator-max-microvolt = <2864000>;
+		};
+
+		vreg_l23a_3p3: l23 {
+			regulator-min-microvolt = <3312000>;
+			regulator-max-microvolt = <3312000>;
+		};
+
+		vreg_l24a_3p075: l24 {
+			regulator-min-microvolt = <3088000>;
+			regulator-max-microvolt = <3088000>;
+		};
+
+		vreg_l25a_3p3: l25 {
+			regulator-min-microvolt = <3104000>;
+			regulator-max-microvolt = <3312000>;
+		};
+
+		vreg_l26a_1p2: l26 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l28_3p0: l28 {
+			regulator-min-microvolt = <3008000>;
+			regulator-max-microvolt = <3008000>;
+		};
+
+		vreg_lvs1a_1p8: lvs1 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		vreg_lvs2a_1p8: lvs2 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+	};
+
+	pmi8998-regulators {
+		compatible = "qcom,rpm-pmi8998-regulators";
+
+		vdd_bob-supply = <&vph_pwr>;
+
+		vreg_bob: bob {
+			regulator-min-microvolt = <3312000>;
+			regulator-max-microvolt = <3600000>;
+		};
+	};
+};
+
+&remoteproc_adsp {
+	status = "okay";
+};
+
+&remoteproc_mss {
+	status = "okay";
+};
+
+&remoteproc_slpi {
+	status = "okay";
+};
+
+&tlmm {
+	gpio-reserved-ranges = <0 4>, <81 4>;
+};
+
+&sdhc2 {
+	status = "okay";
+	cd-gpios = <&tlmm 95 GPIO_ACTIVE_LOW>;
+
+	vmmc-supply = <&vreg_l21a_2p95>;
+	vqmmc-supply = <&vreg_l13a_2p95>;
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sdc2_on &sdc2_cd>;
+	pinctrl-1 = <&sdc2_off &sdc2_cd>;
+};
+
+&stm {
+	status = "okay";
+};
+
+&ufshc {
+	status = "okay";
+	vcc-supply = <&vreg_l20a_2p95>;
+	vccq-supply = <&vreg_l26a_1p2>;
+	vccq2-supply = <&vreg_s4a_1p8>;
+	vcc-max-microamp = <750000>;
+	vccq-max-microamp = <560000>;
+	vccq2-max-microamp = <750000>;
+};
+
+&ufsphy {
+	status = "okay";
+	vdda-phy-supply = <&vreg_l1a_0p875>;
+	vdda-pll-supply = <&vreg_l2a_1p2>;
+	vddp-ref-clk-supply = <&vreg_l26a_1p2>;
+};
+
+&usb3 {
+	status = "okay";
+};
+
+&usb3_dwc3 {
+	dr_mode = "host"; /* Force to host until we have Type-C hooked up */
+};
+
+&usb3phy {
+	status = "okay";
+
+	vdda-phy-supply = <&vreg_l1a_0p875>;
+	vdda-pll-supply = <&vreg_l2a_1p2>;
+};
+
+&wifi {
+	status = "okay";
+
+	vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>;
+	vdd-1.8-xo-supply = <&vreg_l7a_1p8>;
+	vdd-1.3-rfa-supply = <&vreg_l17a_1p3>;
+	vdd-3.3-ch0-supply = <&vreg_l25a_3p3>;
 };
diff --git a/arch/arm64/boot/dts/qcom/msm8998-mtp.dtsi b/arch/arm64/boot/dts/qcom/msm8998-mtp.dtsi
deleted file mode 100644
index af67c641df4e..000000000000
--- a/arch/arm64/boot/dts/qcom/msm8998-mtp.dtsi
+++ /dev/null
@@ -1,421 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/* Copyright (c) 2016, The Linux Foundation. All rights reserved. */
-
-#include "msm8998.dtsi"
-#include "pm8998.dtsi"
-#include "pmi8998.dtsi"
-#include "pm8005.dtsi"
-
-/ {
-	aliases {
-		serial0 = &blsp2_uart1;
-		serial1 = &blsp1_uart3;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	vph_pwr: vph-pwr-regulator {
-		compatible = "regulator-fixed";
-		regulator-name = "vph_pwr";
-		regulator-always-on;
-		regulator-boot-on;
-	};
-};
-
-&blsp1_uart3 {
-	status = "okay";
-
-	bluetooth {
-		compatible = "qcom,wcn3990-bt";
-
-		vddio-supply = <&vreg_s4a_1p8>;
-		vddxo-supply = <&vreg_l7a_1p8>;
-		vddrf-supply = <&vreg_l17a_1p3>;
-		vddch0-supply = <&vreg_l25a_3p3>;
-		max-speed = <3200000>;
-	};
-};
-
-&blsp2_uart1 {
-	status = "okay";
-};
-
-&etf {
-	status = "okay";
-};
-
-&etm1 {
-	status = "okay";
-};
-
-&etm2 {
-	status = "okay";
-};
-
-&etm3 {
-	status = "okay";
-};
-
-&etm4 {
-	status = "okay";
-};
-
-&etm5 {
-	status = "okay";
-};
-
-&etm6 {
-	status = "okay";
-};
-
-&etm7 {
-	status = "okay";
-};
-
-&etm8 {
-	status = "okay";
-};
-
-&etr {
-	status = "okay";
-};
-
-&funnel1 {
-	status = "okay";
-};
-
-&funnel2 {
-	status = "okay";
-};
-
-&funnel3 {
-	status = "okay";
-};
-
-&funnel4 {
-	// FIXME: Figure out why clock late_initcall crashes the board with
-	// this enabled.
-	// status = "okay";
-};
-
-&funnel5 {
-	// FIXME: Figure out why clock late_initcall crashes the board with
-	// this enabled.
-	// status = "okay";
-};
-
-&pcie0 {
-	status = "okay";
-};
-
-&pcie_phy {
-	status = "okay";
-};
-
-&pm8005_lsid1 {
-	pm8005-regulators {
-		compatible = "qcom,pm8005-regulators";
-
-		vdd_s1-supply = <&vph_pwr>;
-
-		pm8005_s1: s1 { /* VDD_GFX supply */
-			regulator-min-microvolt = <524000>;
-			regulator-max-microvolt = <1100000>;
-			regulator-enable-ramp-delay = <500>;
-
-			/* hack until we rig up the gpu consumer */
-			regulator-always-on;
-		};
-	};
-};
-
-&qusb2phy {
-	status = "okay";
-
-	vdda-pll-supply = <&vreg_l12a_1p8>;
-	vdda-phy-dpdm-supply = <&vreg_l24a_3p075>;
-};
-
-&replicator1 {
-	status = "okay";
-};
-
-&rpm_requests {
-	pm8998-regulators {
-		compatible = "qcom,rpm-pm8998-regulators";
-
-		vdd_s1-supply = <&vph_pwr>;
-		vdd_s2-supply = <&vph_pwr>;
-		vdd_s3-supply = <&vph_pwr>;
-		vdd_s4-supply = <&vph_pwr>;
-		vdd_s5-supply = <&vph_pwr>;
-		vdd_s6-supply = <&vph_pwr>;
-		vdd_s7-supply = <&vph_pwr>;
-		vdd_s8-supply = <&vph_pwr>;
-		vdd_s9-supply = <&vph_pwr>;
-		vdd_s10-supply = <&vph_pwr>;
-		vdd_s11-supply = <&vph_pwr>;
-		vdd_s12-supply = <&vph_pwr>;
-		vdd_s13-supply = <&vph_pwr>;
-		vdd_l1_l27-supply = <&vreg_s7a_1p025>;
-		vdd_l2_l8_l17-supply = <&vreg_s3a_1p35>;
-		vdd_l3_l11-supply = <&vreg_s7a_1p025>;
-		vdd_l4_l5-supply = <&vreg_s7a_1p025>;
-		vdd_l6-supply = <&vreg_s5a_2p04>;
-		vdd_l7_l12_l14_l15-supply = <&vreg_s5a_2p04>;
-		vdd_l9-supply = <&vreg_bob>;
-		vdd_l10_l23_l25-supply = <&vreg_bob>;
-		vdd_l13_l19_l21-supply = <&vreg_bob>;
-		vdd_l16_l28-supply = <&vreg_bob>;
-		vdd_l18_l22-supply = <&vreg_bob>;
-		vdd_l20_l24-supply = <&vreg_bob>;
-		vdd_l26-supply = <&vreg_s3a_1p35>;
-		vdd_lvs1_lvs2-supply = <&vreg_s4a_1p8>;
-
-		vreg_s3a_1p35: s3 {
-			regulator-min-microvolt = <1352000>;
-			regulator-max-microvolt = <1352000>;
-		};
-		vreg_s4a_1p8: s4 {
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-			regulator-allow-set-load;
-		};
-		vreg_s5a_2p04: s5 {
-			regulator-min-microvolt = <1904000>;
-			regulator-max-microvolt = <2040000>;
-		};
-		vreg_s7a_1p025: s7 {
-			regulator-min-microvolt = <900000>;
-			regulator-max-microvolt = <1028000>;
-		};
-		vreg_l1a_0p875: l1 {
-			regulator-min-microvolt = <880000>;
-			regulator-max-microvolt = <880000>;
-		};
-		vreg_l2a_1p2: l2 {
-			regulator-min-microvolt = <1200000>;
-			regulator-max-microvolt = <1200000>;
-		};
-		vreg_l3a_1p0: l3 {
-			regulator-min-microvolt = <1000000>;
-			regulator-max-microvolt = <1000000>;
-		};
-		vreg_l5a_0p8: l5 {
-			regulator-min-microvolt = <800000>;
-			regulator-max-microvolt = <800000>;
-		};
-		vreg_l6a_1p8: l6 {
-			regulator-min-microvolt = <1808000>;
-			regulator-max-microvolt = <1808000>;
-		};
-		vreg_l7a_1p8: l7 {
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-		};
-		vreg_l8a_1p2: l8 {
-			regulator-min-microvolt = <1200000>;
-			regulator-max-microvolt = <1200000>;
-		};
-		vreg_l9a_1p8: l9 {
-			regulator-min-microvolt = <1808000>;
-			regulator-max-microvolt = <2960000>;
-		};
-		vreg_l10a_1p8: l10 {
-			regulator-min-microvolt = <1808000>;
-			regulator-max-microvolt = <2960000>;
-		};
-		vreg_l11a_1p0: l11 {
-			regulator-min-microvolt = <1000000>;
-			regulator-max-microvolt = <1000000>;
-		};
-		vreg_l12a_1p8: l12 {
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-		};
-		vreg_l13a_2p95: l13 {
-			regulator-min-microvolt = <1808000>;
-			regulator-max-microvolt = <2960000>;
-		};
-		vreg_l14a_1p88: l14 {
-			regulator-min-microvolt = <1880000>;
-			regulator-max-microvolt = <1880000>;
-		};
-		vreg_l15a_1p8: l15 {
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-		};
-		vreg_l16a_2p7: l16 {
-			regulator-min-microvolt = <2704000>;
-			regulator-max-microvolt = <2704000>;
-		};
-		vreg_l17a_1p3: l17 {
-			regulator-min-microvolt = <1304000>;
-			regulator-max-microvolt = <1304000>;
-		};
-		vreg_l18a_2p7: l18 {
-			regulator-min-microvolt = <2704000>;
-			regulator-max-microvolt = <2704000>;
-		};
-		vreg_l19a_3p0: l19 {
-			regulator-min-microvolt = <3008000>;
-			regulator-max-microvolt = <3008000>;
-		};
-		vreg_l20a_2p95: l20 {
-			regulator-min-microvolt = <2960000>;
-			regulator-max-microvolt = <2960000>;
-			regulator-allow-set-load;
-		};
-		vreg_l21a_2p95: l21 {
-			regulator-min-microvolt = <2960000>;
-			regulator-max-microvolt = <2960000>;
-			regulator-allow-set-load;
-			regulator-system-load = <800000>;
-		};
-		vreg_l22a_2p85: l22 {
-			regulator-min-microvolt = <2864000>;
-			regulator-max-microvolt = <2864000>;
-		};
-		vreg_l23a_3p3: l23 {
-			regulator-min-microvolt = <3312000>;
-			regulator-max-microvolt = <3312000>;
-		};
-		vreg_l24a_3p075: l24 {
-			regulator-min-microvolt = <3088000>;
-			regulator-max-microvolt = <3088000>;
-		};
-		vreg_l25a_3p3: l25 {
-			regulator-min-microvolt = <3104000>;
-			regulator-max-microvolt = <3312000>;
-		};
-		vreg_l26a_1p2: l26 {
-			regulator-min-microvolt = <1200000>;
-			regulator-max-microvolt = <1200000>;
-			regulator-allow-set-load;
-		};
-		vreg_l28_3p0: l28 {
-			regulator-min-microvolt = <3008000>;
-			regulator-max-microvolt = <3008000>;
-		};
-
-		vreg_lvs1a_1p8: lvs1 {
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-		};
-
-		vreg_lvs2a_1p8: lvs2 {
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-		};
-
-	};
-
-	pmi8998-regulators {
-		compatible = "qcom,rpm-pmi8998-regulators";
-
-		vdd_bob-supply = <&vph_pwr>;
-
-		vreg_bob: bob {
-			regulator-min-microvolt = <3312000>;
-			regulator-max-microvolt = <3600000>;
-		};
-	};
-};
-
-&remoteproc_adsp {
-	status = "okay";
-};
-
-&remoteproc_mss {
-	status = "okay";
-};
-
-&remoteproc_slpi {
-	status = "okay";
-};
-
-&tlmm {
-	gpio-reserved-ranges = <0 4>, <81 4>;
-};
-
-&sdhc2 {
-	status = "okay";
-	cd-gpios = <&tlmm 95 GPIO_ACTIVE_LOW>;
-
-	vmmc-supply = <&vreg_l21a_2p95>;
-	vqmmc-supply = <&vreg_l13a_2p95>;
-
-	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&sdc2_clk_on  &sdc2_cmd_on  &sdc2_data_on  &sdc2_cd_on>;
-	pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdc2_cd_off>;
-};
-
-&stm {
-	status = "okay";
-};
-
-&ufshc {
-	status = "okay";
-	vcc-supply = <&vreg_l20a_2p95>;
-	vccq-supply = <&vreg_l26a_1p2>;
-	vccq2-supply = <&vreg_s4a_1p8>;
-	vcc-max-microamp = <750000>;
-	vccq-max-microamp = <560000>;
-	vccq2-max-microamp = <750000>;
-};
-
-&ufsphy {
-	status = "okay";
-	vdda-phy-supply = <&vreg_l1a_0p875>;
-	vdda-pll-supply = <&vreg_l2a_1p2>;
-	vddp-ref-clk-supply = <&vreg_l26a_1p2>;
-};
-
-&usb3 {
-	status = "okay";
-};
-
-&usb3_dwc3 {
-	dr_mode = "host"; /* Force to host until we have Type-C hooked up */
-};
-
-&usb3phy {
-	status = "okay";
-
-	vdda-phy-supply = <&vreg_l1a_0p875>;
-	vdda-pll-supply = <&vreg_l2a_1p2>;
-};
-
-&wifi {
-	status = "okay";
-
-	vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>;
-	vdd-1.8-xo-supply = <&vreg_l7a_1p8>;
-	vdd-1.3-rfa-supply = <&vreg_l17a_1p3>;
-	vdd-3.3-ch0-supply = <&vreg_l25a_3p3>;
-};
-
-/* PINCTRL - board-specific pinctrl */
-&blsp1_uart3_on {
-	rx {
-		/delete-property/ bias-disable;
-		/*
-		 * Configure a pull-up on 45 (RX). This is needed to
-		 * avoid garbage data when the TX pin of the Bluetooth
-		 * module is in tri-state (module powered off or not
-		 * driving the signal yet).
-		 */
-		bias-pull-up;
-	};
-
-	cts {
-		/delete-property/ bias-disable;
-		/*
-		 * Configure a pull-down on 47 (CTS) to match the pull
-		 * of the Bluetooth module.
-		 */
-		bias-pull-down;
-	};
-};
diff --git a/arch/arm64/boot/dts/qcom/msm8998-oneplus-cheeseburger.dts b/arch/arm64/boot/dts/qcom/msm8998-oneplus-cheeseburger.dts
index 9563eb62db88..ef2a88a64d32 100644
--- a/arch/arm64/boot/dts/qcom/msm8998-oneplus-cheeseburger.dts
+++ b/arch/arm64/boot/dts/qcom/msm8998-oneplus-cheeseburger.dts
@@ -32,7 +32,7 @@
 };
 
 &pmi8998_gpio {
-	button_backlight_default: button-backlight-default {
+	button_backlight_default: button-backlight-state {
 		pinconf {
 			pins = "gpio5";
 			function = "normal";
diff --git a/arch/arm64/boot/dts/qcom/msm8998-oneplus-common.dtsi b/arch/arm64/boot/dts/qcom/msm8998-oneplus-common.dtsi
index 654188027f79..62bda23791bb 100644
--- a/arch/arm64/boot/dts/qcom/msm8998-oneplus-common.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8998-oneplus-common.dtsi
@@ -11,9 +11,9 @@
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
 #include "msm8998.dtsi"
+#include "pm8005.dtsi"
 #include "pm8998.dtsi"
 #include "pmi8998.dtsi"
-#include "pm8005.dtsi"
 
 / {
 	/* Required for bootloader to select correct board */
@@ -32,6 +32,19 @@
 			height = <1920>;
 			stride = <(1080 * 4)>;
 			format = "a8r8g8b8";
+			/*
+			* That's a lot of clocks, but it's necessary due
+			* to unused clk cleanup & no panel driver yet..
+			*/
+			clocks = <&mmcc MDSS_AHB_CLK>,
+				 <&mmcc MDSS_AXI_CLK>,
+				 <&mmcc MDSS_VSYNC_CLK>,
+				 <&mmcc MDSS_MDP_CLK>,
+				 <&mmcc MDSS_BYTE0_CLK>,
+				 <&mmcc MDSS_BYTE0_INTF_CLK>,
+				 <&mmcc MDSS_PCLK0_CLK>,
+				 <&mmcc MDSS_ESC0_CLK>;
+			power-domains = <&mmcc MDSS_GDSC>;
 		};
 	};
 
@@ -77,7 +90,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&vol_keys_default>;
 
-		vol-down {
+		button-vol-down {
 			label = "Volume down";
 			gpios = <&pm8998_gpio 5 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_VOLUMEDOWN>;
@@ -85,7 +98,7 @@
 			wakeup-source;
 		};
 
-		vol-up {
+		button-vol-up {
 			label = "Volume up";
 			gpios = <&pm8998_gpio 6 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_VOLUMEUP>;
@@ -101,7 +114,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&hall_sensor_default>;
 
-		hall-sensor {
+		event-hall-sensor {
 			label = "Hall Effect Sensor";
 			gpios = <&tlmm 124 GPIO_ACTIVE_LOW>;
 			linux,input-type = <EV_SW>;
@@ -188,6 +201,23 @@
 	};
 };
 
+&blsp1_i2c6 {
+	status = "okay";
+
+	nfc@28 {
+		compatible = "nxp,nxp-nci-i2c";
+		reg = <0x28>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <92 IRQ_TYPE_LEVEL_HIGH>;
+
+		enable-gpios = <&tlmm 116 GPIO_ACTIVE_HIGH>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&nfc_int_active &nfc_enable_active>;
+	};
+};
+
 &blsp1_uart3 {
 	status = "okay";
 
@@ -228,38 +258,31 @@
 	status = "okay";
 };
 
-&pm8005_lsid1 {
-	pm8005-regulators {
-		compatible = "qcom,pm8005-regulators";
-
-		vdd_s1-supply = <&vph_pwr>;
-
-		pm8005_s1: s1 { /* VDD_GFX supply */
-			regulator-min-microvolt = <524000>;
-			regulator-max-microvolt = <1100000>;
-			regulator-enable-ramp-delay = <500>;
-
-			/* hack until we rig up the gpu consumer */
-			regulator-always-on;
-		};
+&pm8005_regulators {
+	/* VDD_GFX supply */
+	pm8005_s1: s1 {
+		regulator-min-microvolt = <524000>;
+		regulator-max-microvolt = <1100000>;
+		regulator-enable-ramp-delay = <500>;
+		/* Hack until we rig up the gpu consumer */
+		regulator-always-on;
 	};
 };
 
 &pm8998_gpio {
-	vol_keys_default: vol-keys-default {
-		pinconf {
-			pins = "gpio5", "gpio6";
-			function = "normal";
-			bias-pull-up;
-			input-enable;
-			qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
-		};
+	vol_keys_default: vol-keys-state {
+		pins = "gpio5", "gpio6";
+		function = "normal";
+		bias-pull-up;
+		input-enable;
+		qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
 	};
 };
 
 &qusb2phy {
 	status = "okay";
 
+	vdd-supply = <&vreg_l1a_0p875>;
 	vdda-pll-supply = <&vreg_l12a_1p8>;
 	vdda-phy-dpdm-supply = <&vreg_l24a_3p075>;
 };
@@ -300,91 +323,113 @@
 			regulator-min-microvolt = <1352000>;
 			regulator-max-microvolt = <1352000>;
 		};
+
 		vreg_s4a_1p8: s4 {
 			regulator-min-microvolt = <1800000>;
 			regulator-max-microvolt = <1800000>;
 			regulator-allow-set-load;
 		};
+
 		vreg_s5a_2p04: s5 {
 			regulator-min-microvolt = <1904000>;
 			regulator-max-microvolt = <2040000>;
 		};
+
 		vreg_s7a_1p025: s7 {
 			regulator-min-microvolt = <900000>;
 			regulator-max-microvolt = <1028000>;
 		};
+
 		vreg_l1a_0p875: l1 {
 			regulator-min-microvolt = <880000>;
 			regulator-max-microvolt = <880000>;
 		};
+
 		vreg_l2a_1p2: l2 {
 			regulator-min-microvolt = <1200000>;
 			regulator-max-microvolt = <1200000>;
 		};
+
 		vreg_l3a_1p0: l3 {
 			regulator-min-microvolt = <1000000>;
 			regulator-max-microvolt = <1000000>;
 		};
+
 		vreg_l5a_0p8: l5 {
 			regulator-min-microvolt = <800000>;
 			regulator-max-microvolt = <800000>;
 		};
+
 		vreg_l6a_1p8: l6 {
 			regulator-min-microvolt = <1808000>;
 			regulator-max-microvolt = <1808000>;
 		};
+
 		vreg_l7a_1p8: l7 {
 			regulator-min-microvolt = <1800000>;
 			regulator-max-microvolt = <1800000>;
 		};
+
 		vreg_l8a_1p2: l8 {
 			regulator-min-microvolt = <1200000>;
 			regulator-max-microvolt = <1200000>;
 		};
+
 		vreg_l9a_1p8: l9 {
 			regulator-min-microvolt = <1808000>;
 			regulator-max-microvolt = <2960000>;
 		};
+
 		vreg_l10a_1p8: l10 {
 			regulator-min-microvolt = <1808000>;
 			regulator-max-microvolt = <2960000>;
 		};
+
 		vreg_l11a_1p0: l11 {
 			regulator-min-microvolt = <1000000>;
 			regulator-max-microvolt = <1000000>;
 		};
+
 		vreg_l12a_1p8: l12 {
 			regulator-min-microvolt = <1800000>;
 			regulator-max-microvolt = <1800000>;
 		};
+
 		vreg_l13a_2p95: l13 {
 			regulator-min-microvolt = <1808000>;
 			regulator-max-microvolt = <2960000>;
 		};
+
 		vreg_l14a_1p88: l14 {
 			regulator-min-microvolt = <1880000>;
 			regulator-max-microvolt = <1880000>;
 		};
+
 		vreg_l15a_1p8: l15 {
 			regulator-min-microvolt = <1800000>;
 			regulator-max-microvolt = <1800000>;
 		};
+
 		vreg_l16a_2p7: l16 {
 			regulator-min-microvolt = <2704000>;
 			regulator-max-microvolt = <2704000>;
 		};
+
 		vreg_l17a_1p3: l17 {
 			regulator-min-microvolt = <1304000>;
 			regulator-max-microvolt = <1304000>;
 		};
+
 		vreg_l18a_2p7: l18 {
 			regulator-min-microvolt = <2704000>;
 			regulator-max-microvolt = <2704000>;
 		};
+
 		vreg_l19a_3p0: l19 {
 			regulator-min-microvolt = <3008000>;
 			regulator-max-microvolt = <3008000>;
 		};
+
 		vreg_l20a_2p95: l20 {
 			regulator-min-microvolt = <2960000>;
 			regulator-max-microvolt = <2960000>;
@@ -393,34 +438,41 @@
 		vreg_l21a_2p95: l21 {
 			regulator-min-microvolt = <2960000>;
 			regulator-max-microvolt = <2960000>;
-			regulator-allow-set-load;
 			regulator-system-load = <800000>;
+			regulator-allow-set-load;
 		};
+
 		vreg_l22a_2p85: l22 {
 			regulator-min-microvolt = <2864000>;
 			regulator-max-microvolt = <2864000>;
 		};
+
 		vreg_l23a_3p3: l23 {
 			regulator-min-microvolt = <3312000>;
 			regulator-max-microvolt = <3312000>;
 		};
+
 		vreg_l24a_3p075: l24 {
 			regulator-min-microvolt = <3088000>;
 			regulator-max-microvolt = <3088000>;
 		};
+
 		vreg_l25a_3p3: l25 {
 			regulator-min-microvolt = <3104000>;
 			regulator-max-microvolt = <3312000>;
 		};
+
 		vreg_l26a_1p2: l26 {
 			regulator-min-microvolt = <1200000>;
 			regulator-max-microvolt = <1200000>;
 			regulator-allow-set-load;
 		};
+
 		vreg_l28_3p0: l28 {
 			regulator-min-microvolt = <3008000>;
 			regulator-max-microvolt = <3008000>;
 		};
+
 		vreg_lvs1a_1p8: lvs1 { };
 		vreg_lvs2a_1p8: lvs2 { };
 	};
@@ -461,6 +513,20 @@
 		drive-strength = <8>;
 		bias-pull-up;
 	};
+
+	nfc_int_active: nfc-int-active {
+		pins = "gpio92";
+		function = "gpio";
+		drive-strength = <6>;
+		bias-pull-up;
+	};
+
+	nfc_enable_active: nfc-enable-active {
+		pins = "gpio12", "gpio116";
+		function = "gpio";
+		drive-strength = <6>;
+		bias-pull-up;
+	};
 };
 
 &ufshc {
diff --git a/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino-lilac.dts b/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino-lilac.dts
index caacb7c28402..fcaefc1b1e2f 100644
--- a/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino-lilac.dts
+++ b/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino-lilac.dts
@@ -29,3 +29,7 @@
 	regulator-min-microvolt = <2800000>;
 	regulator-max-microvolt = <2800000>;
 };
+
+&vreg_lvs1a_1p8 {
+	status = "disabled";
+};
diff --git a/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino-maple.dts b/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino-maple.dts
index 978495a8a6b9..20fe0394a3c1 100644
--- a/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino-maple.dts
+++ b/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino-maple.dts
@@ -38,7 +38,7 @@
 };
 
 &pmi8998_gpio {
-	disp_dvdd_en: disp-dvdd-en-active {
+	disp_dvdd_en: disp-dvdd-en-active-state {
 		pins = "gpio10";
 		function = "normal";
 		bias-disable;
diff --git a/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino-poplar.dts b/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino-poplar.dts
index 4a1f98a21031..c21333aa73c2 100644
--- a/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino-poplar.dts
+++ b/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino-poplar.dts
@@ -26,11 +26,13 @@
 };
 
 &vreg_l18a_2p85 {
-	regulator-min-microvolt = <2850000>;
-	regulator-max-microvolt = <2850000>;
+	/* Note: Round-down from 2850000 to be a multiple of PLDO step-size 8000 */
+	regulator-min-microvolt = <2848000>;
+	regulator-max-microvolt = <2848000>;
 };
 
 &vreg_l22a_2p85 {
-	regulator-min-microvolt = <2700000>;
-	regulator-max-microvolt = <2700000>;
+	/* Note: Round-down from 2700000 to be a multiple of PLDO step-size 8000 */
+	regulator-min-microvolt = <2696000>;
+	regulator-max-microvolt = <2696000>;
 };
diff --git a/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino.dtsi b/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino.dtsi
index 91e391282181..d08639082247 100644
--- a/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino.dtsi
@@ -5,15 +5,13 @@
  * Copyright (c) 2021, Konrad Dybcio <konrad.dybcio@somainline.org>
  */
 
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
 #include "msm8998.dtsi"
 #include "pm8005.dtsi"
 #include "pm8998.dtsi"
 #include "pmi8998.dtsi"
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/leds/common.h>
-#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
-#include <dt-bindings/sound/qcom,q6afe.h>
-#include <dt-bindings/sound/qcom,q6asm.h>
 
 / {
 	/* required for bootloader to select correct board */
@@ -21,8 +19,6 @@
 	qcom,board-id = <8 0>;
 
 	clocks {
-		compatible = "simple-bus";
-
 		div1_mclk: divclk1 {
 			compatible = "gpio-gate-clock";
 			pinctrl-0 = <&audio_mclk_pin>;
@@ -91,14 +87,21 @@
 		regulator-boot-on;
 	};
 
+	extcon_usb: extcon-usb {
+		compatible = "linux,extcon-usb-gpio";
+		id-gpio = <&tlmm 38 GPIO_ACTIVE_HIGH>;
+		vbus-gpio = <&tlmm 128 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&usb_extcon_active &usb_vbus_active>;
+	};
+
 	gpio-keys {
 		compatible = "gpio-keys";
-		input-name = "gpio-keys";
 		label = "Side buttons";
 		pinctrl-names = "default";
 		pinctrl-0 = <&vol_down_pin_a>, <&cam_focus_pin_a>,
 			    <&cam_snapshot_pin_a>;
-		vol-down {
+		button-vol-down {
 			label = "Volume Down";
 			gpios = <&pm8998_gpio 5 GPIO_ACTIVE_LOW>;
 			linux,input-type = <EV_KEY>;
@@ -107,7 +110,7 @@
 			debounce-interval = <15>;
 		};
 
-		camera-snapshot {
+		button-camera-snapshot {
 			label = "Camera Snapshot";
 			gpios = <&pm8998_gpio 7 GPIO_ACTIVE_LOW>;
 			linux,input-type = <EV_KEY>;
@@ -115,7 +118,7 @@
 			debounce-interval = <15>;
 		};
 
-		camera-focus {
+		button-camera-focus {
 			label = "Camera Focus";
 			gpios = <&pm8998_gpio 8 GPIO_ACTIVE_LOW>;
 			linux,input-type = <EV_KEY>;
@@ -126,12 +129,11 @@
 
 	gpio-hall-sensor {
 		compatible = "gpio-keys";
-		input-name = "hall-sensors";
 		label = "Hall sensors";
 		pinctrl-names = "default";
 		pinctrl-0 = <&hall_sensor0_default>;
 
-		hall-sensor0 {
+		event-hall-sensor0 {
 			label = "Cover Hall Sensor";
 			gpios = <&tlmm 124 GPIO_ACTIVE_LOW>;
 			linux,input-type = <EV_SW>;
@@ -247,6 +249,24 @@
 	status = "okay";
 };
 
+&blsp2_i2c2 {
+	status = "okay";
+
+	proximity@29 {
+		compatible = "st,vl53l0x";
+		reg = <0x29>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <22 IRQ_TYPE_EDGE_FALLING>;
+
+		reset-gpios = <&tlmm 27 GPIO_ACTIVE_LOW>;
+		vdd-supply = <&cam_vio_vreg>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&tof_int &tof_reset>;
+	};
+};
+
 &ibb {
 	regulator-min-microamp = <800000>;
 	regulator-max-microamp = <800000>;
@@ -272,32 +292,19 @@
 	regulator-soft-start;
 };
 
-&mmcc {
-	status = "ok";
-};
-
-&mmss_smmu {
-	status = "ok";
-};
-
-&pm8005_lsid1 {
-	pm8005-regulators {
-		compatible = "qcom,pm8005-regulators";
-
-		vdd_s1-supply = <&vph_pwr>;
-
-		/* VDD_GFX supply */
-		pm8005_s1: s1 {
-			regulator-min-microvolt = <524000>;
-			regulator-max-microvolt = <1088000>;
-			regulator-enable-ramp-delay = <500>;
-			regulator-always-on;
-		};
+&pm8005_regulators {
+	/* VDD_GFX supply */
+	pm8005_s1: s1 {
+		regulator-min-microvolt = <524000>;
+		regulator-max-microvolt = <1088000>;
+		regulator-enable-ramp-delay = <500>;
+		/* Hack until we rig up the gpu consumer */
+		regulator-always-on;
 	};
 };
 
 &pm8998_gpio {
-	vol_down_pin_a: vol-down-active {
+	vol_down_pin_a: vol-down-active-state {
 		pins = "gpio5";
 		function = PMIC_GPIO_FUNC_NORMAL;
 		bias-pull-up;
@@ -305,7 +312,7 @@
 		qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
 	};
 
-	cam_focus_pin_a: cam-focus-btn-active {
+	cam_focus_pin_a: cam-focus-btn-active-state {
 		pins = "gpio7";
 		function = PMIC_GPIO_FUNC_NORMAL;
 		bias-pull-up;
@@ -313,7 +320,7 @@
 		qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
 	};
 
-	cam_snapshot_pin_a: cam-snapshot-btn-active {
+	cam_snapshot_pin_a: cam-snapshot-btn-active-state {
 		pins = "gpio8";
 		function = PMIC_GPIO_FUNC_NORMAL;
 		bias-pull-up;
@@ -321,7 +328,7 @@
 		qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
 	};
 
-	audio_mclk_pin: audio-mclk-pin-active {
+	audio_mclk_pin: audio-mclk-pin-active-state {
 		pins = "gpio13";
 		function = "func2";
 		power-source = <0>;
@@ -329,7 +336,7 @@
 };
 
 &pmi8998_gpio {
-	cam_vio_default: cam-vio-active {
+	cam_vio_default: cam-vio-active-state {
 		pins = "gpio1";
 		function = PMIC_GPIO_FUNC_NORMAL;
 		bias-disable;
@@ -339,7 +346,7 @@
 		power-source = <1>;
 	};
 
-	vib_default: vib-en {
+	vib_default: vib-en-state {
 		pins = "gpio5";
 		function = PMIC_GPIO_FUNC_NORMAL;
 		bias-disable;
@@ -551,8 +558,8 @@
 	vqmmc-supply = <&vreg_l13a_2p95>;
 
 	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&sdc2_clk_on  &sdc2_cmd_on  &sdc2_data_on  &sdc2_cd_on>;
-	pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdc2_cd_off>;
+	pinctrl-0 = <&sdc2_on &sdc2_cd>;
+	pinctrl-1 = <&sdc2_off &sdc2_cd>;
 };
 
 &tlmm {
@@ -608,6 +615,14 @@
 		drive-strength = <2>;
 	};
 
+	tof_int: tof-int {
+		pins = "gpio22";
+		function = "gpio";
+		bias-pull-up;
+		drive-strength = <2>;
+		input-enable;
+	};
+
 	cam1_vdig_default: cam1-vdig-default {
 		pins = "gpio25";
 		function = "gpio";
@@ -615,6 +630,20 @@
 		drive-strength = <2>;
 	};
 
+	usb_extcon_active: usb-extcon-active {
+		pins = "gpio38";
+		function = "gpio";
+		bias-disable;
+		drive-strength = <16>;
+	};
+
+	tof_reset: tof-reset {
+		pins = "gpio27";
+		function = "gpio";
+		bias-disable;
+		drive-strength = <2>;
+	};
+
 	hall_sensor0_default: acc-cover-open {
 		pins = "gpio124";
 		function = "gpio";
@@ -630,6 +659,14 @@
 		bias-pull-up;
 	};
 
+	usb_vbus_active: usb-vbus-active {
+		pins = "gpio128";
+		function = "gpio";
+		bias-disable;
+		drive-strength = <2>;
+		output-low;
+	};
+
 	ts_vddio_en: ts-vddio-en-default {
 		pins = "gpio133";
 		function = "gpio";
@@ -660,6 +697,7 @@
 &usb3_dwc3 {
 	/* Force to peripheral until we have Type-C hooked up */
 	dr_mode = "peripheral";
+	extcon = <&extcon_usb>;
 };
 
 &usb3phy {
diff --git a/arch/arm64/boot/dts/qcom/msm8998.dtsi b/arch/arm64/boot/dts/qcom/msm8998.dtsi
index 408f265e277b..f05f16ac5cc1 100644
--- a/arch/arm64/boot/dts/qcom/msm8998.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8998.dtsi
@@ -138,15 +138,9 @@
 			cpu-idle-states = <&LITTLE_CPU_SLEEP_0 &LITTLE_CPU_SLEEP_1>;
 			next-level-cache = <&L2_0>;
 			L2_0: l2-cache {
-				compatible = "arm,arch-cache";
+				compatible = "cache";
 				cache-level = <2>;
 			};
-			L1_I_0: l1-icache {
-				compatible = "arm,arch-cache";
-			};
-			L1_D_0: l1-dcache {
-				compatible = "arm,arch-cache";
-			};
 		};
 
 		CPU1: cpu@1 {
@@ -157,12 +151,6 @@
 			capacity-dmips-mhz = <1024>;
 			cpu-idle-states = <&LITTLE_CPU_SLEEP_0 &LITTLE_CPU_SLEEP_1>;
 			next-level-cache = <&L2_0>;
-			L1_I_1: l1-icache {
-				compatible = "arm,arch-cache";
-			};
-			L1_D_1: l1-dcache {
-				compatible = "arm,arch-cache";
-			};
 		};
 
 		CPU2: cpu@2 {
@@ -173,12 +161,6 @@
 			capacity-dmips-mhz = <1024>;
 			cpu-idle-states = <&LITTLE_CPU_SLEEP_0 &LITTLE_CPU_SLEEP_1>;
 			next-level-cache = <&L2_0>;
-			L1_I_2: l1-icache {
-				compatible = "arm,arch-cache";
-			};
-			L1_D_2: l1-dcache {
-				compatible = "arm,arch-cache";
-			};
 		};
 
 		CPU3: cpu@3 {
@@ -189,12 +171,6 @@
 			capacity-dmips-mhz = <1024>;
 			cpu-idle-states = <&LITTLE_CPU_SLEEP_0 &LITTLE_CPU_SLEEP_1>;
 			next-level-cache = <&L2_0>;
-			L1_I_3: l1-icache {
-				compatible = "arm,arch-cache";
-			};
-			L1_D_3: l1-dcache {
-				compatible = "arm,arch-cache";
-			};
 		};
 
 		CPU4: cpu@100 {
@@ -206,15 +182,9 @@
 			cpu-idle-states = <&BIG_CPU_SLEEP_0 &BIG_CPU_SLEEP_1>;
 			next-level-cache = <&L2_1>;
 			L2_1: l2-cache {
-				compatible = "arm,arch-cache";
+				compatible = "cache";
 				cache-level = <2>;
 			};
-			L1_I_100: l1-icache {
-				compatible = "arm,arch-cache";
-			};
-			L1_D_100: l1-dcache {
-				compatible = "arm,arch-cache";
-			};
 		};
 
 		CPU5: cpu@101 {
@@ -225,12 +195,6 @@
 			capacity-dmips-mhz = <1536>;
 			cpu-idle-states = <&BIG_CPU_SLEEP_0 &BIG_CPU_SLEEP_1>;
 			next-level-cache = <&L2_1>;
-			L1_I_101: l1-icache {
-				compatible = "arm,arch-cache";
-			};
-			L1_D_101: l1-dcache {
-				compatible = "arm,arch-cache";
-			};
 		};
 
 		CPU6: cpu@102 {
@@ -241,12 +205,6 @@
 			capacity-dmips-mhz = <1536>;
 			cpu-idle-states = <&BIG_CPU_SLEEP_0 &BIG_CPU_SLEEP_1>;
 			next-level-cache = <&L2_1>;
-			L1_I_102: l1-icache {
-				compatible = "arm,arch-cache";
-			};
-			L1_D_102: l1-dcache {
-				compatible = "arm,arch-cache";
-			};
 		};
 
 		CPU7: cpu@103 {
@@ -257,12 +215,6 @@
 			capacity-dmips-mhz = <1536>;
 			cpu-idle-states = <&BIG_CPU_SLEEP_0 &BIG_CPU_SLEEP_1>;
 			next-level-cache = <&L2_1>;
-			L1_I_103: l1-icache {
-				compatible = "arm,arch-cache";
-			};
-			L1_D_103: l1-dcache {
-				compatible = "arm,arch-cache";
-			};
 		};
 
 		cpu-map {
@@ -356,12 +308,6 @@
 		};
 	};
 
-	tcsr_mutex: hwlock {
-		compatible = "qcom,tcsr-mutex";
-		syscon = <&tcsr_mutex_regs 0 0x1000>;
-		#hwlock-cells = <1>;
-	};
-
 	psci {
 		compatible = "arm,psci-1.0";
 		method = "smc";
@@ -674,7 +620,7 @@
 			};
 		};
 
-		gpu-thermal-bottom {
+		gpu-bottom-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 
@@ -689,7 +635,7 @@
 			};
 		};
 
-		gpu-thermal-top {
+		gpu-top-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 
@@ -863,6 +809,21 @@
 
 			clock-names = "xo", "sleep_clk";
 			clocks = <&xo>, <&sleep_clk>;
+
+			/*
+			 * The hypervisor typically configures the memory region where these clocks
+			 * reside as read-only for the HLOS. If the HLOS tried to enable or disable
+			 * these clocks on a device with such configuration (e.g. because they are
+			 * enabled but unused during boot-up), the device will most likely decide
+			 * to reboot.
+			 * In light of that, we are conservative here and we list all such clocks
+			 * as protected. The board dts (or a user-supplied dts) can override the
+			 * list of protected clocks if it differs from the norm, and it is in fact
+			 * desired for the HLOS to manage these clocks
+			 */
+			protected-clocks = <AGGRE2_SNOC_NORTH_AXI>,
+					   <SSC_XO>,
+					   <SSC_CNOC_AHBS_CLK>;
 		};
 
 		rpm_msg_ram: sram@778000 {
@@ -871,7 +832,7 @@
 		};
 
 		qfprom: qfprom@784000 {
-			compatible = "qcom,qfprom";
+			compatible = "qcom,msm8998-qfprom", "qcom,qfprom";
 			reg = <0x00784000 0x621c>;
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -962,7 +923,7 @@
 			interrupts = <GIC_SPI 405 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "msi";
 			interrupt-map-mask = <0 0 0 0x7>;
-			interrupt-map =	<0 0 0 1 &intc 0 0 135 IRQ_TYPE_LEVEL_HIGH>,
+			interrupt-map = <0 0 0 1 &intc 0 0 135 IRQ_TYPE_LEVEL_HIGH>,
 					<0 0 0 2 &intc 0 0 136 IRQ_TYPE_LEVEL_HIGH>,
 					<0 0 0 3 &intc 0 0 138 IRQ_TYPE_LEVEL_HIGH>,
 					<0 0 0 4 &intc 0 0 139 IRQ_TYPE_LEVEL_HIGH>;
@@ -1080,9 +1041,15 @@
 			};
 		};
 
-		tcsr_mutex_regs: syscon@1f40000 {
-			compatible = "syscon";
-			reg = <0x01f40000 0x40000>;
+		tcsr_mutex: hwlock@1f40000 {
+			compatible = "qcom,tcsr-mutex";
+			reg = <0x01f40000 0x20000>;
+			#hwlock-cells = <1>;
+		};
+
+		tcsr_regs_1: syscon@1f60000 {
+			compatible = "qcom,msm8998-tcsr", "syscon";
+			reg = <0x01f60000 0x20000>;
 		};
 
 		tlmm: pinctrl@3400000 {
@@ -1090,85 +1057,58 @@
 			reg = <0x03400000 0xc00000>;
 			interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
 			gpio-controller;
-			#gpio-cells = <0x2>;
+			#gpio-cells = <2>;
 			interrupt-controller;
-			#interrupt-cells = <0x2>;
+			#interrupt-cells = <2>;
 
-			sdc2_clk_on: sdc2_clk_on {
-				config {
+			sdc2_on: sdc2-on {
+				clk {
 					pins = "sdc2_clk";
-					bias-disable;
 					drive-strength = <16>;
-				};
-			};
-
-			sdc2_clk_off: sdc2_clk_off {
-				config {
-					pins = "sdc2_clk";
 					bias-disable;
-					drive-strength = <2>;
 				};
-			};
 
-			sdc2_cmd_on: sdc2_cmd_on {
-				config {
+				cmd {
 					pins = "sdc2_cmd";
-					bias-pull-up;
 					drive-strength = <10>;
-				};
-			};
-
-			sdc2_cmd_off: sdc2_cmd_off {
-				config {
-					pins = "sdc2_cmd";
 					bias-pull-up;
-					drive-strength = <2>;
 				};
-			};
 
-			sdc2_data_on: sdc2_data_on {
-				config {
+				data {
 					pins = "sdc2_data";
-					bias-pull-up;
 					drive-strength = <10>;
+					bias-pull-up;
 				};
 			};
 
-			sdc2_data_off: sdc2_data_off {
-				config {
-					pins = "sdc2_data";
-					bias-pull-up;
+			sdc2_off: sdc2-off {
+				clk {
+					pins = "sdc2_clk";
 					drive-strength = <2>;
+					bias-disable;
 				};
-			};
 
-			sdc2_cd_on: sdc2_cd_on {
-				mux {
-					pins = "gpio95";
-					function = "gpio";
+				cmd {
+					pins = "sdc2_cmd";
+					drive-strength = <2>;
+					bias-pull-up;
 				};
 
-				config {
-					pins = "gpio95";
-					bias-pull-up;
+				data {
+					pins = "sdc2_data";
 					drive-strength = <2>;
+					bias-pull-up;
 				};
 			};
 
-			sdc2_cd_off: sdc2_cd_off {
-				mux {
-					pins = "gpio95";
-					function = "gpio";
-				};
-
-				config {
-					pins = "gpio95";
-					bias-pull-up;
-					drive-strength = <2>;
-				};
+			sdc2_cd: sdc2-cd {
+				pins = "gpio95";
+				function = "gpio";
+				bias-pull-up;
+				drive-strength = <2>;
 			};
 
-			blsp1_uart3_on: blsp1_uart3_on {
+			blsp1_uart3_on: blsp1-uart3-on {
 				tx {
 					pins = "gpio45";
 					function = "blsp_uart3_a";
@@ -1400,7 +1340,7 @@
 			resets = <&gcc GCC_MSS_RESTART>;
 			reset-names = "mss_restart";
 
-			qcom,halt-regs = <&tcsr_mutex_regs 0x23000 0x25000 0x24000>;
+			qcom,halt-regs = <&tcsr_regs_1 0x3000 0x5000 0x4000>;
 
 			power-domains = <&rpmpd MSM8998_VDDCX>,
 					<&rpmpd MSM8998_VDDMX>;
@@ -1446,11 +1386,10 @@
 			iommus = <&adreno_smmu 0>;
 			operating-points-v2 = <&gpu_opp_table>;
 			power-domains = <&rpmpd MSM8998_VDDMX>;
-			#stream-id-cells = <16>;
 			status = "disabled";
 
 			gpu_opp_table: opp-table {
-				compatible  = "operating-points-v2";
+				compatible = "operating-points-v2";
 				opp-710000097 {
 					opp-hz = /bits/ 64 <710000097>;
 					opp-level = <RPM_SMD_LEVEL_TURBO>;
@@ -2057,10 +1996,13 @@
 			clocks = <&gcc GCC_CFG_NOC_USB3_AXI_CLK>,
 				 <&gcc GCC_USB30_MASTER_CLK>,
 				 <&gcc GCC_AGGRE1_USB3_AXI_CLK>,
-				 <&gcc GCC_USB30_MOCK_UTMI_CLK>,
-				 <&gcc GCC_USB30_SLEEP_CLK>;
-			clock-names = "cfg_noc", "core", "iface", "mock_utmi",
-				      "sleep";
+				 <&gcc GCC_USB30_SLEEP_CLK>,
+				 <&gcc GCC_USB30_MOCK_UTMI_CLK>;
+			clock-names = "cfg_noc",
+				      "core",
+				      "iface",
+				      "sleep",
+				      "mock_utmi";
 
 			assigned-clocks = <&gcc GCC_USB30_MOCK_UTMI_CLK>,
 					  <&gcc GCC_USB30_MASTER_CLK>;
@@ -2074,7 +2016,7 @@
 
 			resets = <&gcc GCC_USB_30_BCR>;
 
-			usb3_dwc3: dwc3@a800000 {
+			usb3_dwc3: usb@a800000 {
 				compatible = "snps,dwc3";
 				reg = <0x0a800000 0xcd00>;
 				interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>;
@@ -2111,7 +2053,7 @@
 				      <0xc010600 0x128>,
 				      <0xc010800 0x200>;
 				#phy-cells = <0>;
-				#clock-cells = <1>;
+				#clock-cells = <0>;
 				clocks = <&gcc GCC_USB3_PHY_PIPE_CLK>;
 				clock-names = "pipe0";
 				clock-output-names = "usb3_phy_pipe_clk_src";
@@ -2133,10 +2075,10 @@
 			nvmem-cells = <&qusb2_hstx_trim>;
 		};
 
-		sdhc2: sdhci@c0a4900 {
-			compatible = "qcom,sdhci-msm-v4";
+		sdhc2: mmc@c0a4900 {
+			compatible = "qcom,msm8998-sdhci", "qcom,sdhci-msm-v4";
 			reg = <0x0c0a4900 0x314>, <0x0c0a4000 0x800>;
-			reg-names = "hc_mem", "core_mem";
+			reg-names = "hc", "core";
 
 			interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 221 IRQ_TYPE_LEVEL_HIGH>;
@@ -2446,7 +2388,6 @@
 			#reset-cells = <1>;
 			#power-domain-cells = <1>;
 			reg = <0xc8c0000 0x40000>;
-			status = "disabled";
 
 			clock-names = "xo",
 				      "gpll0",
@@ -2481,7 +2422,6 @@
 				 <&mmcc BIMC_SMMU_AXI_CLK>;
 			clock-names = "iface-mm", "iface-smmu",
 				      "bus-mm", "bus-smmu";
-			status = "disabled";
 
 			#global-interrupts = <0>;
 			interrupts =
diff --git a/arch/arm64/boot/dts/qcom/pm6150l.dtsi b/arch/arm64/boot/dts/qcom/pm6150l.dtsi
index 3ca2860bb0cf..f02c223ef448 100644
--- a/arch/arm64/boot/dts/qcom/pm6150l.dtsi
+++ b/arch/arm64/boot/dts/qcom/pm6150l.dtsi
@@ -20,10 +20,29 @@
 			#size-cells = <0>;
 			#io-channel-cells = <1>;
 
+			adc-chan@0 {
+				reg = <ADC5_REF_GND>;
+				qcom,pre-scaling = <1 1>;
+				label = "ref_gnd";
+			};
+
+			adc-chan@1 {
+				reg = <ADC5_1P25VREF>;
+				qcom,pre-scaling = <1 1>;
+				label = "vref_1p25";
+			};
+
 			adc-chan@6 {
 				reg = <ADC5_DIE_TEMP>;
+				qcom,pre-scaling = <1 1>;
 				label = "die_temp";
 			};
+
+			adc-chan@83 {
+				reg = <ADC5_VPH_PWR>;
+				qcom,pre-scaling = <1 3>;
+				label = "vph_pwr";
+			};
 		};
 
 		pm6150l_adc_tm: adc-tm@3500 {
@@ -52,5 +71,15 @@
 		reg = <0x5 SPMI_USID>;
 		#address-cells = <1>;
 		#size-cells = <0>;
+
+		pm6150l_wled: leds@d800 {
+			compatible = "qcom,pm6150l-wled";
+			reg = <0xd800>, <0xd900>;
+			interrupts = <0x5 0xd8 0x1 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "ovp";
+			label = "backlight";
+
+			status = "disabled";
+		};
 	};
 };
diff --git a/arch/arm64/boot/dts/qcom/pm6350.dtsi b/arch/arm64/boot/dts/qcom/pm6350.dtsi
index c5d85064562b..ecf9b9919182 100644
--- a/arch/arm64/boot/dts/qcom/pm6350.dtsi
+++ b/arch/arm64/boot/dts/qcom/pm6350.dtsi
@@ -36,9 +36,10 @@
 		};
 
 		pm6350_gpios: gpios@c000 {
-			compatible = "qcom,pm6350-gpio";
+			compatible = "qcom,pm6350-gpio", "qcom,spmi-gpio";
 			reg = <0xc000>;
 			gpio-controller;
+			gpio-ranges = <&pm6350_gpios 0 0 9>;
 			#gpio-cells = <2>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
diff --git a/arch/arm64/boot/dts/qcom/pm660.dtsi b/arch/arm64/boot/dts/qcom/pm660.dtsi
index d0ef8a1675e2..e1622b16c08b 100644
--- a/arch/arm64/boot/dts/qcom/pm660.dtsi
+++ b/arch/arm64/boot/dts/qcom/pm660.dtsi
@@ -54,14 +54,24 @@
 			mode-bootloader = <0x2>;
 			mode-recovery = <0x1>;
 
-			pwrkey {
+			pon_pwrkey: pwrkey {
 				compatible = "qcom,pm8941-pwrkey";
 				interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>;
 				debounce = <15625>;
 				bias-pull-up;
 				linux,code = <KEY_POWER>;
+
+				status = "disabled";
 			};
 
+			pon_resin: resin {
+				compatible = "qcom,pm8941-resin";
+				interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>;
+				debounce = <15625>;
+				bias-pull-up;
+
+				status = "disabled";
+			};
 		};
 
 		pm660_temp: temp-alarm@2400 {
@@ -161,7 +171,7 @@
 		};
 
 		pm660_gpios: gpios@c000 {
-			compatible = "qcom,pm660-gpio";
+			compatible = "qcom,pm660-gpio", "qcom,spmi-gpio";
 			reg = <0xc000>;
 			gpio-controller;
 			gpio-ranges = <&pm660_gpios 0 0 13>;
@@ -177,7 +187,7 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		pm660_spmi_regulators: pm660-regulators {
+		pm660_spmi_regulators: regulators {
 			compatible = "qcom,pm660-regulators";
 		};
 	};
diff --git a/arch/arm64/boot/dts/qcom/pm660l.dtsi b/arch/arm64/boot/dts/qcom/pm660l.dtsi
index cfef42353611..8aa0a5078772 100644
--- a/arch/arm64/boot/dts/qcom/pm660l.dtsi
+++ b/arch/arm64/boot/dts/qcom/pm660l.dtsi
@@ -65,9 +65,15 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
+		pm660l_lpg: pwm {
+			compatible = "qcom,pm660l-lpg";
+
+			status = "disabled";
+		};
+
 		pm660l_wled: leds@d800 {
 			compatible = "qcom,pm660l-wled";
-			reg = <0xd800 0xd900>;
+			reg = <0xd800>, <0xd900>;
 			interrupts = <0x3 0xd8 0x1 IRQ_TYPE_EDGE_RISING>;
 			interrupt-names = "ovp";
 			label = "backlight";
@@ -75,7 +81,7 @@
 			status = "disabled";
 		};
 
-		pm660l_spmi_regulators: pm660l-regulators {
+		pm660l_spmi_regulators: regulators {
 			compatible = "qcom,pm660l-regulators";
 		};
 	};
diff --git a/arch/arm64/boot/dts/qcom/pm7250b.dtsi b/arch/arm64/boot/dts/qcom/pm7250b.dtsi
new file mode 100644
index 000000000000..61f7a6345150
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/pm7250b.dtsi
@@ -0,0 +1,149 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (C) 2022 Luca Weiss <luca.weiss@fairphone.com>
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/spmi/spmi.h>
+
+/ {
+	thermal-zones {
+		pm7250b-thermal {
+			polling-delay-passive = <100>;
+			polling-delay = <0>;
+
+			thermal-sensors = <&pm7250b_temp>;
+
+			trips {
+				trip0 {
+					temperature = <95000>;
+					hysteresis = <0>;
+					type = "passive";
+				};
+
+				trip1 {
+					temperature = <115000>;
+					hysteresis = <0>;
+					type = "hot";
+				};
+
+				trip2 {
+					temperature = <145000>;
+					hysteresis = <0>;
+					type = "critical";
+				};
+			};
+		};
+	};
+};
+
+&spmi_bus {
+	pmic@2 {
+		compatible = "qcom,pm7250b", "qcom,spmi-pmic";
+		reg = <0x2 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pm7250b_temp: temp-alarm@2400 {
+			compatible = "qcom,spmi-temp-alarm";
+			reg = <0x2400>;
+			interrupts = <0x2 0x24 0x0 IRQ_TYPE_EDGE_BOTH>;
+			io-channels = <&pm7250b_adc ADC5_DIE_TEMP>;
+			io-channel-names = "thermal";
+			#thermal-sensor-cells = <0>;
+		};
+
+		pm7250b_adc: adc@3100 {
+			compatible = "qcom,spmi-adc5";
+			reg = <0x3100>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			#io-channel-cells = <1>;
+			interrupts = <0x2 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
+
+			adc-chan@0 {
+				reg = <ADC5_REF_GND>;
+				qcom,pre-scaling = <1 1>;
+				label = "ref_gnd";
+			};
+
+			adc-chan@1 {
+				reg = <ADC5_1P25VREF>;
+				qcom,pre-scaling = <1 1>;
+				label = "vref_1p25";
+			};
+
+			adc-chan@2 {
+				reg = <ADC5_DIE_TEMP>;
+				qcom,pre-scaling = <1 1>;
+				label = "die_temp";
+			};
+
+			adc-chan@7 {
+				reg = <ADC5_USB_IN_I>;
+				qcom,pre-scaling = <1 1>;
+				label = "usb_in_i_uv";
+			};
+
+			adc-chan@8 {
+				reg = <ADC5_USB_IN_V_16>;
+				qcom,pre-scaling = <1 16>;
+				label = "usb_in_v_div_16";
+			};
+
+			adc-chan@9 {
+				reg = <ADC5_CHG_TEMP>;
+				qcom,pre-scaling = <1 1>;
+				label = "chg_temp";
+			};
+
+			adc-chan@e {
+				reg = <ADC5_AMUX_THM2>;
+				qcom,hw-settle-time = <200>;
+				qcom,pre-scaling = <1 1>;
+				label = "smb1390_therm";
+			};
+
+			adc-chan@1e {
+				reg = <ADC5_MID_CHG_DIV6>;
+				qcom,pre-scaling = <1 6>;
+				label = "chg_mid";
+			};
+
+			adc-chan@83 {
+				reg = <ADC5_VPH_PWR>;
+				qcom,pre-scaling = <1 3>;
+				label = "vph_pwr";
+			};
+
+			adc-chan@84 {
+				reg = <ADC5_VBAT_SNS>;
+				qcom,pre-scaling = <1 3>;
+				label = "vbat_sns";
+			};
+
+			adc-chan@99 {
+				reg = <ADC5_SBUx>;
+				qcom,pre-scaling = <1 3>;
+				label = "chg_sbux";
+			};
+		};
+
+		pm7250b_adc_tm: adc-tm@3500 {
+			compatible = "qcom,spmi-adc-tm5";
+			reg = <0x3500>;
+			interrupts = <0x2 0x35 0x0 IRQ_TYPE_EDGE_RISING>;
+			#thermal-sensor-cells = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+	};
+
+	pmic@3 {
+		compatible = "qcom,pm7250b", "qcom,spmi-pmic";
+		reg = <0x3 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+};
diff --git a/arch/arm64/boot/dts/qcom/pm8005.dtsi b/arch/arm64/boot/dts/qcom/pm8005.dtsi
index 3f97607d8baa..50fb6c753bf8 100644
--- a/arch/arm64/boot/dts/qcom/pm8005.dtsi
+++ b/arch/arm64/boot/dts/qcom/pm8005.dtsi
@@ -28,5 +28,9 @@
 		reg = <0x5 SPMI_USID>;
 		#address-cells = <1>;
 		#size-cells = <0>;
+
+		pm8005_regulators: regulators {
+			compatible = "qcom,pm8005-regulators";
+		};
 	};
 };
diff --git a/arch/arm64/boot/dts/qcom/pm8009.dtsi b/arch/arm64/boot/dts/qcom/pm8009.dtsi
index b126d7e7e4fb..0c2c424be0ea 100644
--- a/arch/arm64/boot/dts/qcom/pm8009.dtsi
+++ b/arch/arm64/boot/dts/qcom/pm8009.dtsi
@@ -19,9 +19,10 @@
 		};
 
 		pm8009_gpios: gpio@c000 {
-			compatible = "qcom,pm8005-gpio";
+			compatible = "qcom,pm8005-gpio", "qcom,spmi-gpio";
 			reg = <0xc000>;
 			gpio-controller;
+			gpio-ranges = <&pm8009_gpios 0 0 4>;
 			#gpio-cells = <2>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
diff --git a/arch/arm64/boot/dts/qcom/pm8150.dtsi b/arch/arm64/boot/dts/qcom/pm8150.dtsi
index 0df76f7b1cc1..574fa95a2871 100644
--- a/arch/arm64/boot/dts/qcom/pm8150.dtsi
+++ b/arch/arm64/boot/dts/qcom/pm8150.dtsi
@@ -47,7 +47,7 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		pon: power-on@800 {
+		pon: pon@800 {
 			compatible = "qcom,pm8998-pon";
 			reg = <0x0800>;
 			mode-bootloader = <0x2>;
@@ -127,9 +127,10 @@
 		};
 
 		pm8150_gpios: gpio@c000 {
-			compatible = "qcom,pm8150-gpio";
+			compatible = "qcom,pm8150-gpio", "qcom,spmi-gpio";
 			reg = <0xc000>;
 			gpio-controller;
+			gpio-ranges = <&pm8150_gpios 0 0 10>;
 			#gpio-cells = <2>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
diff --git a/arch/arm64/boot/dts/qcom/pm8150b.dtsi b/arch/arm64/boot/dts/qcom/pm8150b.dtsi
index 058cc5107c75..cdded791d96e 100644
--- a/arch/arm64/boot/dts/qcom/pm8150b.dtsi
+++ b/arch/arm64/boot/dts/qcom/pm8150b.dtsi
@@ -46,7 +46,7 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		power-on@800 {
+		pon@800 {
 			compatible = "qcom,pm8916-pon";
 			reg = <0x0800>;
 
@@ -112,9 +112,10 @@
 		};
 
 		pm8150b_gpios: gpio@c000 {
-			compatible = "qcom,pm8150b-gpio";
+			compatible = "qcom,pm8150b-gpio", "qcom,spmi-gpio";
 			reg = <0xc000>;
 			gpio-controller;
+			gpio-ranges = <&pm8150b_gpios 0 0 12>;
 			#gpio-cells = <2>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
@@ -126,5 +127,15 @@
 		reg = <0x3 SPMI_USID>;
 		#address-cells = <1>;
 		#size-cells = <0>;
+
+		pm8150b_lpg: pwm {
+			compatible = "qcom,pm8150b-lpg";
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+			#pwm-cells = <2>;
+
+			status = "disabled";
+		};
 	};
 };
diff --git a/arch/arm64/boot/dts/qcom/pm8150l.dtsi b/arch/arm64/boot/dts/qcom/pm8150l.dtsi
index 52f094a2b713..135bfb8d629b 100644
--- a/arch/arm64/boot/dts/qcom/pm8150l.dtsi
+++ b/arch/arm64/boot/dts/qcom/pm8150l.dtsi
@@ -46,7 +46,7 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		power-on@800 {
+		pon@800 {
 			compatible = "qcom,pm8916-pon";
 			reg = <0x0800>;
 
@@ -100,9 +100,10 @@
 		};
 
 		pm8150l_gpios: gpio@c000 {
-			compatible = "qcom,pm8150l-gpio";
+			compatible = "qcom,pm8150l-gpio", "qcom,spmi-gpio";
 			reg = <0xc000>;
 			gpio-controller;
+			gpio-ranges = <&pm8150l_gpios 0 0 12>;
 			#gpio-cells = <2>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
@@ -114,5 +115,16 @@
 		reg = <0x5 SPMI_USID>;
 		#address-cells = <1>;
 		#size-cells = <0>;
+
+		pm8150l_lpg: pwm {
+			compatible = "qcom,pm8150l-lpg";
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+			#pwm-cells = <2>;
+
+			status = "disabled";
+		};
+
 	};
 };
diff --git a/arch/arm64/boot/dts/qcom/pm8350.dtsi b/arch/arm64/boot/dts/qcom/pm8350.dtsi
index 308f9ca7c744..2dfeb99300d7 100644
--- a/arch/arm64/boot/dts/qcom/pm8350.dtsi
+++ b/arch/arm64/boot/dts/qcom/pm8350.dtsi
@@ -6,6 +6,30 @@
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/spmi/spmi.h>
 
+/ {
+	thermal-zones {
+		pm8350_thermal: pm8350c-thermal {
+			polling-delay-passive = <100>;
+			polling-delay = <0>;
+			thermal-sensors = <&pm8350_temp_alarm>;
+
+			trips {
+				pm8350_trip0: trip0 {
+					temperature = <95000>;
+					hysteresis = <0>;
+					type = "passive";
+				};
+
+				pm8350_crit: pm8350c-crit {
+					temperature = <115000>;
+					hysteresis = <0>;
+					type = "critical";
+				};
+			};
+		};
+	};
+};
+
 &spmi_bus {
 	pm8350: pmic@1 {
 		compatible = "qcom,pm8350", "qcom,spmi-pmic";
@@ -13,10 +37,18 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
+		pm8350_temp_alarm: temp-alarm@a00 {
+			compatible = "qcom,spmi-temp-alarm";
+			reg = <0xa00>;
+			interrupts = <0x1 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
+			#thermal-sensor-cells = <0>;
+		};
+
 		pm8350_gpios: gpio@8800 {
-			compatible = "qcom,pm8350-gpio";
+			compatible = "qcom,pm8350-gpio", "qcom,spmi-gpio";
 			reg = <0x8800>;
 			gpio-controller;
+			gpio-ranges = <&pm8350_gpios 0 0 10>;
 			#gpio-cells = <2>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
diff --git a/arch/arm64/boot/dts/qcom/pm8350b.dtsi b/arch/arm64/boot/dts/qcom/pm8350b.dtsi
index b23bb1d49a4d..f1c7bd9d079c 100644
--- a/arch/arm64/boot/dts/qcom/pm8350b.dtsi
+++ b/arch/arm64/boot/dts/qcom/pm8350b.dtsi
@@ -6,6 +6,30 @@
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/spmi/spmi.h>
 
+/ {
+	thermal-zones {
+		pm8350b_thermal: pm8350c-thermal {
+			polling-delay-passive = <100>;
+			polling-delay = <0>;
+			thermal-sensors = <&pm8350b_temp_alarm>;
+
+			trips {
+				pm8350b_trip0: trip0 {
+					temperature = <95000>;
+					hysteresis = <0>;
+					type = "passive";
+				};
+
+				pm8350b_crit: pm8350c-crit {
+					temperature = <115000>;
+					hysteresis = <0>;
+					type = "critical";
+				};
+			};
+		};
+	};
+};
+
 &spmi_bus {
 	pm8350b: pmic@3 {
 		compatible = "qcom,pm8350b", "qcom,spmi-pmic";
@@ -13,10 +37,18 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
+		pm8350b_temp_alarm: temp-alarm@a00 {
+			compatible = "qcom,spmi-temp-alarm";
+			reg = <0xa00>;
+			interrupts = <0x3 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
+			#thermal-sensor-cells = <0>;
+		};
+
 		pm8350b_gpios: gpio@8800 {
-			compatible = "qcom,pm8350b-gpio";
+			compatible = "qcom,pm8350b-gpio", "qcom,spmi-gpio";
 			reg = <0x8800>;
 			gpio-controller;
+			gpio-ranges = <&pm8350b_gpios 0 0 8>;
 			#gpio-cells = <2>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
diff --git a/arch/arm64/boot/dts/qcom/pm8350c.dtsi b/arch/arm64/boot/dts/qcom/pm8350c.dtsi
index e1b75ae0a823..f28e71487d5c 100644
--- a/arch/arm64/boot/dts/qcom/pm8350c.dtsi
+++ b/arch/arm64/boot/dts/qcom/pm8350c.dtsi
@@ -29,26 +29,34 @@
 			interrupt-controller;
 			#interrupt-cells = <2>;
 		};
+
+		pm8350c_pwm: pwm {
+			compatible = "qcom,pm8350c-pwm";
+			#pwm-cells = <2>;
+			status = "disabled";
+		};
 	};
 };
 
-&thermal_zones {
-	pm8350c_thermal: pm8350c-thermal {
-		polling-delay-passive = <100>;
-		polling-delay = <0>;
-		thermal-sensors = <&pm8350c_temp_alarm>;
-
-		trips {
-			pm8350c_trip0: trip0 {
-				temperature = <95000>;
-				hysteresis = <0>;
-				type = "passive";
-			};
+/ {
+	thermal-zones {
+		pm8350c_thermal: pm8350c-thermal {
+			polling-delay-passive = <100>;
+			polling-delay = <0>;
+			thermal-sensors = <&pm8350c_temp_alarm>;
+
+			trips {
+				pm8350c_trip0: trip0 {
+					temperature = <95000>;
+					hysteresis = <0>;
+					type = "passive";
+				};
 
-			pm8350c_crit: pm8350c-crit {
-				temperature = <115000>;
-				hysteresis = <0>;
-				type = "critical";
+				pm8350c_crit: pm8350c-crit {
+					temperature = <115000>;
+					hysteresis = <0>;
+					type = "critical";
+				};
 			};
 		};
 	};
diff --git a/arch/arm64/boot/dts/qcom/pm8450.dtsi b/arch/arm64/boot/dts/qcom/pm8450.dtsi
new file mode 100644
index 000000000000..ae5bce3cf46e
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/pm8450.dtsi
@@ -0,0 +1,59 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2022, Linaro Limited
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/spmi/spmi.h>
+
+/ {
+	thermal-zones {
+		pm8450-thermal {
+			polling-delay-passive = <100>;
+			polling-delay = <0>;
+
+			thermal-sensors = <&pm8450_temp_alarm>;
+
+			trips {
+				trip0 {
+					temperature = <95000>;
+					hysteresis = <0>;
+					type = "passive";
+				};
+
+				trip1 {
+					temperature = <115000>;
+					hysteresis = <0>;
+					type = "hot";
+				};
+			};
+		};
+	};
+};
+
+
+&spmi_bus {
+	pm8450: pmic@7 {
+		compatible = "qcom,pm8450", "qcom,spmi-pmic";
+		reg = <0x7 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pm8450_temp_alarm: temp-alarm@a00 {
+			compatible = "qcom,spmi-temp-alarm";
+			reg = <0xa00>;
+			interrupts = <0x7 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
+			#thermal-sensor-cells = <0>;
+		};
+
+		pm8450_gpios: gpio@8800 {
+			compatible = "qcom,pm8450-gpio", "qcom,spmi-gpio";
+			reg = <0x8800>;
+			gpio-controller;
+			gpio-ranges = <&pm8450_gpios 0 0 4>;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+};
diff --git a/arch/arm64/boot/dts/qcom/pm8916.dtsi b/arch/arm64/boot/dts/qcom/pm8916.dtsi
index d58902432812..606c2a6d1f0f 100644
--- a/arch/arm64/boot/dts/qcom/pm8916.dtsi
+++ b/arch/arm64/boot/dts/qcom/pm8916.dtsi
@@ -108,14 +108,13 @@
 		};
 
 		pm8916_gpios: gpios@c000 {
-			compatible = "qcom,pm8916-gpio";
+			compatible = "qcom,pm8916-gpio", "qcom,spmi-gpio";
 			reg = <0xc000>;
 			gpio-controller;
+			gpio-ranges = <&pm8916_gpios 0 0 4>;
 			#gpio-cells = <2>;
-			interrupts = <0 0xc0 0 IRQ_TYPE_NONE>,
-				     <0 0xc1 0 IRQ_TYPE_NONE>,
-				     <0 0xc2 0 IRQ_TYPE_NONE>,
-				     <0 0xc3 0 IRQ_TYPE_NONE>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
 		};
 	};
 
@@ -125,6 +124,14 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
+		pm8916_pwm: pwm {
+			compatible = "qcom,pm8916-pwm";
+
+			#pwm-cells = <2>;
+
+			status = "disabled";
+		};
+
 		pm8916_vib: vibrator@c000 {
 			compatible = "qcom,pm8916-vib";
 			reg = <0xc000>;
diff --git a/arch/arm64/boot/dts/qcom/pm8953.dtsi b/arch/arm64/boot/dts/qcom/pm8953.dtsi
new file mode 100644
index 000000000000..a1d36f9ebbd2
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/pm8953.dtsi
@@ -0,0 +1,90 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/* Copyright (c) 2022, The Linux Foundation. All rights reserved. */
+
+#include <dt-bindings/iio/qcom,spmi-vadc.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/spmi/spmi.h>
+
+&spmi_bus {
+	pmic@0 {
+		compatible = "qcom,pm8953", "qcom,spmi-pmic";
+		reg = <0 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pm8953_pon: pon@800 {
+			compatible = "qcom,pm8916-pon";
+			reg = <0x800>;
+			mode-bootloader = <0x2>;
+			mode-recovery = <0x1>;
+
+			pwrkey {
+				compatible = "qcom,pm8941-pwrkey";
+				interrupts = <0x00 0x08 0 IRQ_TYPE_EDGE_BOTH>;
+				debounce = <15625>;
+				bias-pull-up;
+				linux,code = <KEY_POWER>;
+			};
+
+			pm8953_resin: resin {
+				compatible = "qcom,pm8941-resin";
+				interrupts = <0x00 0x08 1 IRQ_TYPE_EDGE_BOTH>;
+				debounce = <15625>;
+				bias-pull-up;
+				status = "disabled";
+			};
+		};
+
+		temp-alarm@2400 {
+			compatible = "qcom,spmi-temp-alarm";
+			reg = <0x2400>;
+			interrupts = <0x0 0x24 0x0 IRQ_TYPE_EDGE_RISING>;
+			io-channels = <&pm8953_vadc VADC_DIE_TEMP>;
+			io-channel-names = "thermal";
+			#thermal-sensor-cells = <0>;
+		};
+
+		pm8953_vadc: adc@3100 {
+			compatible = "qcom,spmi-vadc";
+			reg = <0x3100>;
+			interrupts = <0x00 0x31 0x00 0x01>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			#io-channel-cells = <1>;
+
+			adc-chan@8 {
+				reg = <VADC_DIE_TEMP>;
+			};
+			adc-chan@9 {
+				reg = <VADC_REF_625MV>;
+			};
+			adc-chan@a {
+				reg = <VADC_REF_1250MV>;
+			};
+			adc-chan@c {
+				reg = <VADC_SPARE1>;
+			};
+			adc-chan@e {
+				reg = <VADC_GND_REF>;
+			};
+			adc-chan@f {
+				reg = <VADC_VDD_VADC>;
+			};
+		};
+
+		rtc@6000 {
+			compatible = "qcom,pm8941-rtc";
+			reg = <0x6000>, <0x6100>;
+			reg-names = "rtc", "alarm";
+			interrupts = <0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>;
+		};
+	};
+
+	pmic@1 {
+		compatible = "qcom,pm8953", "qcom,spmi-pmic";
+		reg = <1 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+};
diff --git a/arch/arm64/boot/dts/qcom/pm8994.dtsi b/arch/arm64/boot/dts/qcom/pm8994.dtsi
index 5ab46117d737..e92e5ac414d3 100644
--- a/arch/arm64/boot/dts/qcom/pm8994.dtsi
+++ b/arch/arm64/boot/dts/qcom/pm8994.dtsi
@@ -135,6 +135,16 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
+		pm8994_lpg: pwm {
+			compatible = "qcom,pm8994-lpg";
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+			#pwm-cells = <2>;
+
+			status = "disabled";
+		};
+
 		pm8994_spmi_regulators: regulators {
 			compatible = "qcom,pm8994-regulators";
 		};
diff --git a/arch/arm64/boot/dts/qcom/pm8998.dtsi b/arch/arm64/boot/dts/qcom/pm8998.dtsi
index 6f5bb6b37ec2..d09f2954b6f9 100644
--- a/arch/arm64/boot/dts/qcom/pm8998.dtsi
+++ b/arch/arm64/boot/dts/qcom/pm8998.dtsi
@@ -84,6 +84,16 @@
 			};
 		};
 
+		pm8998_adc_tm: adc-tm@3400 {
+			compatible = "qcom,spmi-adc-tm-hc";
+			reg = <0x3400>;
+			interrupts = <0x0 0x34 0x0 IRQ_TYPE_EDGE_RISING>;
+			#thermal-sensor-cells = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
 		rtc@6000 {
 			compatible = "qcom,pm8941-rtc";
 			reg = <0x6000>, <0x6100>;
diff --git a/arch/arm64/boot/dts/qcom/pmi8994.dtsi b/arch/arm64/boot/dts/qcom/pmi8994.dtsi
index 6e7c252568e6..542c215dde10 100644
--- a/arch/arm64/boot/dts/qcom/pmi8994.dtsi
+++ b/arch/arm64/boot/dts/qcom/pmi8994.dtsi
@@ -19,6 +19,16 @@
 			interrupt-controller;
 			#interrupt-cells = <2>;
 		};
+
+		pmi8994_mpps: mpps@a000 {
+			compatible = "qcom,pmi8994-mpp", "qcom,spmi-mpp";
+			reg = <0xa000>;
+			gpio-controller;
+			gpio-ranges = <&pmi8994_mpps 0 0 4>;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
 	};
 
 	pmic@3 {
@@ -27,6 +37,16 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
+		pmi8994_lpg: pwm {
+			compatible = "qcom,pmi8994-lpg";
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+			#pwm-cells = <2>;
+
+			status = "disabled";
+		};
+
 		pmi8994_spmi_regulators: regulators {
 			compatible = "qcom,pmi8994-regulators";
 			#address-cells = <1>;
@@ -35,7 +55,7 @@
 
 		pmi8994_wled: wled@d800 {
 			compatible = "qcom,pmi8994-wled";
-			reg = <0xd800 0xd900>;
+			reg = <0xd800>, <0xd900>;
 			interrupts = <3 0xd8 0x02 IRQ_TYPE_EDGE_RISING>;
 			interrupt-names = "short";
 			qcom,cabc;
diff --git a/arch/arm64/boot/dts/qcom/pmi8998.dtsi b/arch/arm64/boot/dts/qcom/pmi8998.dtsi
index 0fef5f113f05..3852a012bb0f 100644
--- a/arch/arm64/boot/dts/qcom/pmi8998.dtsi
+++ b/arch/arm64/boot/dts/qcom/pmi8998.dtsi
@@ -42,9 +42,19 @@
 			};
 		};
 
+		pmi8998_lpg: pwm {
+			compatible = "qcom,pmi8998-lpg";
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+			#pwm-cells = <2>;
+
+			status = "disabled";
+		};
+
 		pmi8998_wled: leds@d800 {
 			compatible = "qcom,pmi8998-wled";
-			reg = <0xd800 0xd900>;
+			reg = <0xd800>, <0xd900>;
 			interrupts = <0x3 0xd8 0x1 IRQ_TYPE_EDGE_RISING>,
 				     <0x3 0xd8 0x2 IRQ_TYPE_EDGE_RISING>;
 			interrupt-names = "ovp", "short";
@@ -52,6 +62,5 @@
 
 			status = "disabled";
 		};
-
 	};
 };
diff --git a/arch/arm64/boot/dts/qcom/pmk8350.dtsi b/arch/arm64/boot/dts/qcom/pmk8350.dtsi
index 769f9726806f..a7ec9d11946d 100644
--- a/arch/arm64/boot/dts/qcom/pmk8350.dtsi
+++ b/arch/arm64/boot/dts/qcom/pmk8350.dtsi
@@ -19,16 +19,17 @@
 			compatible = "qcom,pm8998-pon";
 			reg = <0x1300>;
 
-			pwrkey {
+			pon_pwrkey: pwrkey {
 				compatible = "qcom,pmk8350-pwrkey";
 				interrupts = <0x0 0x13 0x7 IRQ_TYPE_EDGE_BOTH>;
 				linux,code = <KEY_POWER>;
+				status = "disabled";
 			};
 
-			resin {
+			pon_resin: resin {
 				compatible = "qcom,pmk8350-resin";
 				interrupts = <0x0 0x13 0x6 IRQ_TYPE_EDGE_BOTH>;
-				linux,code = <KEY_VOLUMEDOWN>;
+				status = "disabled";
 			};
 		};
 
@@ -38,16 +39,13 @@
 			#address-cells = <1>;
 			#size-cells = <0>;
 			interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
-			interrupt-names = "eoc-int-en-set";
 			#io-channel-cells = <1>;
-			io-channel-ranges;
 		};
 
 		pmk8350_adc_tm: adc-tm@3400 {
 			compatible = "qcom,adc-tm7";
 			reg = <0x3400>;
 			interrupts = <0x0 0x34 0x0 IRQ_TYPE_EDGE_RISING>;
-			interrupt-names = "threshold";
 			#address-cells = <1>;
 			#size-cells = <0>;
 			#thermal-sensor-cells = <1>;
diff --git a/arch/arm64/boot/dts/qcom/pmm8155au_1.dtsi b/arch/arm64/boot/dts/qcom/pmm8155au_1.dtsi
index 7072e5a2e73f..20c5d60c8c2c 100644
--- a/arch/arm64/boot/dts/qcom/pmm8155au_1.dtsi
+++ b/arch/arm64/boot/dts/qcom/pmm8155au_1.dtsi
@@ -46,7 +46,7 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		pon: power-on@800 {
+		pon: pon@800 {
 			compatible = "qcom,pm8916-pon";
 			reg = <0x0800>;
 			pwrkey {
@@ -116,7 +116,7 @@
 		};
 
 		pmm8155au_1_gpios: gpio@c000 {
-			compatible = "qcom,pmm8155au-gpio";
+			compatible = "qcom,pmm8155au-gpio", "qcom,spmi-gpio";
 			reg = <0xc000>;
 			gpio-controller;
 			#gpio-cells = <2>;
diff --git a/arch/arm64/boot/dts/qcom/pmm8155au_2.dtsi b/arch/arm64/boot/dts/qcom/pmm8155au_2.dtsi
index 72075964fbb9..1da4606e8ee6 100644
--- a/arch/arm64/boot/dts/qcom/pmm8155au_2.dtsi
+++ b/arch/arm64/boot/dts/qcom/pmm8155au_2.dtsi
@@ -45,7 +45,7 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		power-on@800 {
+		pon@800 {
 			compatible = "qcom,pm8916-pon";
 			reg = <0x0800>;
 
@@ -89,7 +89,7 @@
 		};
 
 		pmm8155au_2_gpios: gpio@c000 {
-			compatible = "qcom,pmm8155au-gpio";
+			compatible = "qcom,pmm8155au-gpio", "qcom,spmi-gpio";
 			reg = <0xc000>;
 			gpio-controller;
 			#gpio-cells = <2>;
diff --git a/arch/arm64/boot/dts/qcom/pmr735a.dtsi b/arch/arm64/boot/dts/qcom/pmr735a.dtsi
index b4b6ba24f845..febda50779f9 100644
--- a/arch/arm64/boot/dts/qcom/pmr735a.dtsi
+++ b/arch/arm64/boot/dts/qcom/pmr735a.dtsi
@@ -32,23 +32,25 @@
 	};
 };
 
-&thermal_zones {
-	pmr735a_thermal: pmr735a-thermal {
-		polling-delay-passive = <100>;
-		polling-delay = <0>;
-		thermal-sensors = <&pmr735a_temp_alarm>;
+/ {
+	thermal-zones {
+		pmr735a_thermal: pmr735a-thermal {
+			polling-delay-passive = <100>;
+			polling-delay = <0>;
+			thermal-sensors = <&pmr735a_temp_alarm>;
 
-		trips {
-			pmr735a_trip0: trip0 {
-				temperature = <95000>;
-				hysteresis = <0>;
-				type = "passive";
-			};
+			trips {
+				pmr735a_trip0: trip0 {
+					temperature = <95000>;
+					hysteresis = <0>;
+					type = "passive";
+				};
 
-			pmr735a_crit: pmr735a-crit {
-				temperature = <115000>;
-				hysteresis = <0>;
-				type = "critical";
+				pmr735a_crit: pmr735a-crit {
+					temperature = <115000>;
+					hysteresis = <0>;
+					type = "critical";
+				};
 			};
 		};
 	};
diff --git a/arch/arm64/boot/dts/qcom/pmr735b.dtsi b/arch/arm64/boot/dts/qcom/pmr735b.dtsi
index 1144086280f5..ec24c4478005 100644
--- a/arch/arm64/boot/dts/qcom/pmr735b.dtsi
+++ b/arch/arm64/boot/dts/qcom/pmr735b.dtsi
@@ -6,6 +6,30 @@
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/spmi/spmi.h>
 
+/ {
+	thermal-zones {
+		pmr735a_thermal: pmr735a-thermal {
+			polling-delay-passive = <100>;
+			polling-delay = <0>;
+			thermal-sensors = <&pmr735b_temp_alarm>;
+
+			trips {
+				pmr735b_trip0: trip0 {
+					temperature = <95000>;
+					hysteresis = <0>;
+					type = "passive";
+				};
+
+				pmr735b_crit: pmr735a-crit {
+					temperature = <115000>;
+					hysteresis = <0>;
+					type = "critical";
+				};
+			};
+		};
+	};
+};
+
 &spmi_bus {
 	pmr735b: pmic@5 {
 		compatible = "qcom,pmr735b", "qcom,spmi-pmic";
@@ -13,10 +37,18 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 
+		pmr735b_temp_alarm: temp-alarm@a00 {
+			compatible = "qcom,spmi-temp-alarm";
+			reg = <0xa00>;
+			interrupts = <0x5 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
+			#thermal-sensor-cells = <0>;
+		};
+
 		pmr735b_gpios: gpio@8800 {
-			compatible = "qcom,pmr735b-gpio";
+			compatible = "qcom,pmr735b-gpio", "qcom,spmi-gpio";
 			reg = <0x8800>;
 			gpio-controller;
+			gpio-ranges = <&pmr735b_gpios 0 0 4>;
 			#gpio-cells = <2>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
diff --git a/arch/arm64/boot/dts/qcom/pms405.dtsi b/arch/arm64/boot/dts/qcom/pms405.dtsi
index 172be177fc8f..634b0681d04c 100644
--- a/arch/arm64/boot/dts/qcom/pms405.dtsi
+++ b/arch/arm64/boot/dts/qcom/pms405.dtsi
@@ -32,28 +32,19 @@
 
 &spmi_bus {
 	pms405_0: pms405@0 {
-		compatible = "qcom,spmi-pmic";
+		compatible = "qcom,pms405", "qcom,spmi-pmic";
 		reg = <0x0 SPMI_USID>;
 		#address-cells = <1>;
 		#size-cells = <0>;
 
 		pms405_gpios: gpio@c000 {
-			compatible = "qcom,pms405-gpio";
+			compatible = "qcom,pms405-gpio", "qcom,spmi-gpio";
 			reg = <0xc000>;
 			gpio-controller;
+			gpio-ranges = <&pms405_gpios 0 0 12>;
 			#gpio-cells = <2>;
-			interrupts = <0 0xc0 0 IRQ_TYPE_NONE>,
-				<0 0xc1 0 IRQ_TYPE_NONE>,
-				<0 0xc2 0 IRQ_TYPE_NONE>,
-				<0 0xc3 0 IRQ_TYPE_NONE>,
-				<0 0xc4 0 IRQ_TYPE_NONE>,
-				<0 0xc5 0 IRQ_TYPE_NONE>,
-				<0 0xc6 0 IRQ_TYPE_NONE>,
-				<0 0xc7 0 IRQ_TYPE_NONE>,
-				<0 0xc8 0 IRQ_TYPE_NONE>,
-				<0 0xc9 0 IRQ_TYPE_NONE>,
-				<0 0xca 0 IRQ_TYPE_NONE>,
-				<0 0xcb 0 IRQ_TYPE_NONE>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
 		};
 
 		pon@800 {
@@ -139,7 +130,7 @@
 	};
 
 	pms405_1: pms405@1 {
-		compatible = "qcom,spmi-pmic";
+		compatible = "qcom,pms405", "qcom,spmi-pmic";
 		reg = <0x1 SPMI_USID>;
 
 		pms405_spmi_regulators: regulators {
diff --git a/arch/arm64/boot/dts/qcom/qcs404-evb.dtsi b/arch/arm64/boot/dts/qcom/qcs404-evb.dtsi
index a80c578484ba..1678ef0f8684 100644
--- a/arch/arm64/boot/dts/qcom/qcs404-evb.dtsi
+++ b/arch/arm64/boot/dts/qcom/qcs404-evb.dtsi
@@ -99,7 +99,7 @@
 &pcie {
 	status = "okay";
 
-	perst-gpio = <&tlmm 43 GPIO_ACTIVE_LOW>;
+	perst-gpios = <&tlmm 43 GPIO_ACTIVE_LOW>;
 
 	pinctrl-names = "default";
 	pinctrl-0 = <&perst_state>;
@@ -304,7 +304,7 @@
 };
 
 &pms405_gpios {
-	usb_vbus_boost_pin: usb-vbus-boost-pin {
+	usb_vbus_boost_pin: usb-vbus-boost-state {
 		pinconf {
 			pins = "gpio3";
 			function = PMIC_GPIO_FUNC_NORMAL;
@@ -312,7 +312,7 @@
 			power-source = <1>;
 		};
 	};
-	usb3_vbus_pin: usb3-vbus-pin {
+	usb3_vbus_pin: usb3-vbus-state {
 		pinconf {
 			pins = "gpio12";
 			function = PMIC_GPIO_FUNC_NORMAL;
@@ -337,9 +337,10 @@
 &usb3 {
 	status = "okay";
 
-	dwc3@7580000 {
-		dr_mode = "host";
-	};
+};
+
+&usb3_dwc3 {
+	dr_mode = "host";
 };
 
 &usb2_phy_prim {
diff --git a/arch/arm64/boot/dts/qcom/qcs404.dtsi b/arch/arm64/boot/dts/qcom/qcs404.dtsi
index 6db753b49326..80f2d05595fa 100644
--- a/arch/arm64/boot/dts/qcom/qcs404.dtsi
+++ b/arch/arm64/boot/dts/qcom/qcs404.dtsi
@@ -110,7 +110,7 @@
 		};
 	};
 
-	cpu_opp_table: cpu-opp-table {
+	cpu_opp_table: opp-table-cpu {
 		compatible = "operating-points-v2-kryo-cpu";
 		opp-shared;
 
@@ -128,7 +128,7 @@
 		};
 	};
 
-	cpr_opp_table: cpr-opp-table {
+	cpr_opp_table: opp-table-cpr {
 		compatible = "operating-points-v2-qcom-level";
 
 		cpr_opp1: opp1 {
@@ -226,7 +226,7 @@
 			qcom,glink-channels = "rpm_requests";
 
 			rpmcc: clock-controller {
-				compatible = "qcom,rpmcc-qcs404";
+				compatible = "qcom,rpmcc-qcs404", "qcom,rpmcc";
 				#clock-cells = <1>;
 			};
 
@@ -295,12 +295,6 @@
 		hwlocks = <&tcsr_mutex 3>;
 	};
 
-	tcsr_mutex: hwlock {
-		compatible = "qcom,tcsr-mutex";
-		syscon = <&tcsr_mutex_regs 0 0x1000>;
-		#hwlock-cells = <1>;
-	};
-
 	soc: soc@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -366,7 +360,7 @@
 		};
 
 		qfprom: qfprom@a4000 {
-			compatible = "qcom,qfprom";
+			compatible = "qcom,qcs404-qfprom", "qcom,qfprom";
 			reg = <0x000a4000 0x1000>;
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -529,7 +523,7 @@
 		};
 
 		usb3: usb@7678800 {
-			compatible = "qcom,dwc3";
+			compatible = "qcom,qcs404-dwc3", "qcom,dwc3";
 			reg = <0x07678800 0x400>;
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -544,11 +538,11 @@
 			assigned-clock-rates = <19200000>, <200000000>;
 			status = "disabled";
 
-			dwc3@7580000 {
+			usb3_dwc3: usb@7580000 {
 				compatible = "snps,dwc3";
 				reg = <0x07580000 0xcd00>;
 				interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
-				phys = <&usb2_phy_sec>, <&usb3_phy>;
+				phys = <&usb2_phy_prim>, <&usb3_phy>;
 				phy-names = "usb2-phy", "usb3-phy";
 				snps,has-lpm-erratum;
 				snps,hird-threshold = /bits/ 8 <0x10>;
@@ -558,7 +552,7 @@
 		};
 
 		usb2: usb@79b8800 {
-			compatible = "qcom,dwc3";
+			compatible = "qcom,qcs404-dwc3", "qcom,dwc3";
 			reg = <0x079b8800 0x400>;
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -573,11 +567,11 @@
 			assigned-clock-rates = <19200000>, <133333333>;
 			status = "disabled";
 
-			dwc3@78c0000 {
+			usb@78c0000 {
 				compatible = "snps,dwc3";
 				reg = <0x078c0000 0xcc00>;
 				interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
-				phys = <&usb2_phy_prim>;
+				phys = <&usb2_phy_sec>;
 				phy-names = "usb2-phy";
 				snps,has-lpm-erratum;
 				snps,hird-threshold = /bits/ 8 <0x10>;
@@ -669,8 +663,25 @@
 			};
 
 			blsp1_spi1_default: blsp1-spi1-default {
-				pins = "gpio22", "gpio23", "gpio24", "gpio25";
-				function = "blsp_spi1";
+				mosi {
+					pins = "gpio22";
+					function = "blsp_spi_mosi_a1";
+				};
+
+				miso {
+					pins = "gpio23";
+					function = "blsp_spi_miso_a1";
+				};
+
+				cs_n {
+					pins = "gpio24";
+					function = "blsp_spi_cs_n_a1";
+				};
+
+				clk {
+					pins = "gpio25";
+					function = "blsp_spi_clk_a1";
+				};
 			};
 
 			blsp1_spi2_default: blsp1-spi2-default {
@@ -709,13 +720,14 @@
 			assigned-clock-rates = <19200000>;
 		};
 
-		tcsr_mutex_regs: syscon@1905000 {
-			compatible = "syscon";
+		tcsr_mutex: hwlock@1905000 {
+			compatible = "qcom,tcsr-mutex";
 			reg = <0x01905000 0x20000>;
+			#hwlock-cells = <1>;
 		};
 
 		tcsr: syscon@1937000 {
-			compatible = "syscon";
+			compatible = "qcom,qcs404-tcsr", "syscon";
 			reg = <0x01937000 0x25000>;
 		};
 
@@ -789,7 +801,7 @@
 			status = "disabled";
 		};
 
-		sdcc1: sdcc@7804000 {
+		sdcc1: mmc@7804000 {
 			compatible = "qcom,qcs404-sdhci", "qcom,sdhci-msm-v5";
 			reg = <0x07804000 0x1000>, <0x7805000 0x1000>;
 			reg-names = "hc", "cqhci";
@@ -798,10 +810,10 @@
 				     <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "hc_irq", "pwr_irq";
 
-			clocks = <&gcc GCC_SDCC1_APPS_CLK>,
-				 <&gcc GCC_SDCC1_AHB_CLK>,
+			clocks = <&gcc GCC_SDCC1_AHB_CLK>,
+				 <&gcc GCC_SDCC1_APPS_CLK>,
 				 <&xo_board>;
-			clock-names = "core", "iface", "xo";
+			clock-names = "iface", "core", "xo";
 
 			status = "disabled";
 		};
@@ -823,8 +835,8 @@
 			interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&gcc GCC_BLSP1_UART0_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
 			clock-names = "core", "iface";
-			dmas = <&blsp1_dma 1>, <&blsp1_dma 0>;
-			dma-names = "rx", "tx";
+			dmas = <&blsp1_dma 0>, <&blsp1_dma 1>;
+			dma-names = "tx", "rx";
 			pinctrl-names = "default";
 			pinctrl-0 = <&blsp1_uart0_default>;
 			status = "disabled";
@@ -836,8 +848,8 @@
 			interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&gcc GCC_BLSP1_UART1_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
 			clock-names = "core", "iface";
-			dmas = <&blsp1_dma 3>, <&blsp1_dma 2>;
-			dma-names = "rx", "tx";
+			dmas = <&blsp1_dma 2>, <&blsp1_dma 3>;
+			dma-names = "tx", "rx";
 			pinctrl-names = "default";
 			pinctrl-0 = <&blsp1_uart1_default>;
 			status = "disabled";
@@ -849,8 +861,8 @@
 			interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&gcc GCC_BLSP1_UART2_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
 			clock-names = "core", "iface";
-			dmas = <&blsp1_dma 5>, <&blsp1_dma 4>;
-			dma-names = "rx", "tx";
+			dmas = <&blsp1_dma 4>, <&blsp1_dma 5>;
+			dma-names = "tx", "rx";
 			pinctrl-names = "default";
 			pinctrl-0 = <&blsp1_uart2_default>;
 			status = "okay";
@@ -903,8 +915,8 @@
 			interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&gcc GCC_BLSP1_UART3_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>;
 			clock-names = "core", "iface";
-			dmas = <&blsp1_dma 7>, <&blsp1_dma 6>;
-			dma-names = "rx", "tx";
+			dmas = <&blsp1_dma 6>, <&blsp1_dma 7>;
+			dma-names = "tx", "rx";
 			pinctrl-names = "default";
 			pinctrl-0 = <&blsp1_uart3_default>;
 			status = "disabled";
@@ -914,9 +926,9 @@
 			compatible = "qcom,i2c-qup-v2.2.1";
 			reg = <0x078b5000 0x600>;
 			interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc GCC_BLSP1_AHB_CLK>,
-				 <&gcc GCC_BLSP1_QUP0_I2C_APPS_CLK>;
-			clock-names = "iface", "core";
+			clocks = <&gcc GCC_BLSP1_QUP0_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
 			pinctrl-names = "default";
 			pinctrl-0 = <&blsp1_i2c0_default>;
 			#address-cells = <1>;
@@ -928,9 +940,9 @@
 			compatible = "qcom,spi-qup-v2.2.1";
 			reg = <0x078b5000 0x600>;
 			interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc GCC_BLSP1_AHB_CLK>,
-				 <&gcc GCC_BLSP1_QUP0_SPI_APPS_CLK>;
-			clock-names = "iface", "core";
+			clocks = <&gcc GCC_BLSP1_QUP0_SPI_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
 			pinctrl-names = "default";
 			pinctrl-0 = <&blsp1_spi0_default>;
 			#address-cells = <1>;
@@ -942,9 +954,9 @@
 			compatible = "qcom,i2c-qup-v2.2.1";
 			reg = <0x078b6000 0x600>;
 			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc GCC_BLSP1_AHB_CLK>,
-				 <&gcc GCC_BLSP1_QUP1_I2C_APPS_CLK>;
-			clock-names = "iface", "core";
+			clocks = <&gcc GCC_BLSP1_QUP1_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
 			pinctrl-names = "default";
 			pinctrl-0 = <&blsp1_i2c1_default>;
 			#address-cells = <1>;
@@ -956,9 +968,9 @@
 			compatible = "qcom,spi-qup-v2.2.1";
 			reg = <0x078b6000 0x600>;
 			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc GCC_BLSP1_AHB_CLK>,
-				 <&gcc GCC_BLSP1_QUP1_SPI_APPS_CLK>;
-			clock-names = "iface", "core";
+			clocks = <&gcc GCC_BLSP1_QUP1_SPI_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
 			pinctrl-names = "default";
 			pinctrl-0 = <&blsp1_spi1_default>;
 			#address-cells = <1>;
@@ -970,9 +982,9 @@
 			compatible = "qcom,i2c-qup-v2.2.1";
 			reg = <0x078b7000 0x600>;
 			interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc GCC_BLSP1_AHB_CLK>,
-				 <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>;
-			clock-names = "iface", "core";
+			clocks = <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
 			pinctrl-names = "default";
 			pinctrl-0 = <&blsp1_i2c2_default>;
 			#address-cells = <1>;
@@ -984,9 +996,9 @@
 			compatible = "qcom,spi-qup-v2.2.1";
 			reg = <0x078b7000 0x600>;
 			interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc GCC_BLSP1_AHB_CLK>,
-				 <&gcc GCC_BLSP1_QUP2_SPI_APPS_CLK>;
-			clock-names = "iface", "core";
+			clocks = <&gcc GCC_BLSP1_QUP2_SPI_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
 			pinctrl-names = "default";
 			pinctrl-0 = <&blsp1_spi2_default>;
 			#address-cells = <1>;
@@ -998,9 +1010,9 @@
 			compatible = "qcom,i2c-qup-v2.2.1";
 			reg = <0x078b8000 0x600>;
 			interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc GCC_BLSP1_AHB_CLK>,
-				 <&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>;
-			clock-names = "iface", "core";
+			clocks = <&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
 			pinctrl-names = "default";
 			pinctrl-0 = <&blsp1_i2c3_default>;
 			#address-cells = <1>;
@@ -1012,9 +1024,9 @@
 			compatible = "qcom,spi-qup-v2.2.1";
 			reg = <0x078b8000 0x600>;
 			interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc GCC_BLSP1_AHB_CLK>,
-				 <&gcc GCC_BLSP1_QUP3_SPI_APPS_CLK>;
-			clock-names = "iface", "core";
+			clocks = <&gcc GCC_BLSP1_QUP3_SPI_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
 			pinctrl-names = "default";
 			pinctrl-0 = <&blsp1_spi3_default>;
 			#address-cells = <1>;
@@ -1026,9 +1038,9 @@
 			compatible = "qcom,i2c-qup-v2.2.1";
 			reg = <0x078b9000 0x600>;
 			interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc GCC_BLSP1_AHB_CLK>,
-				 <&gcc GCC_BLSP1_QUP4_I2C_APPS_CLK>;
-			clock-names = "iface", "core";
+			clocks = <&gcc GCC_BLSP1_QUP4_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
 			pinctrl-names = "default";
 			pinctrl-0 = <&blsp1_i2c4_default>;
 			#address-cells = <1>;
@@ -1040,9 +1052,9 @@
 			compatible = "qcom,spi-qup-v2.2.1";
 			reg = <0x078b9000 0x600>;
 			interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc GCC_BLSP1_AHB_CLK>,
-				 <&gcc GCC_BLSP1_QUP4_SPI_APPS_CLK>;
-			clock-names = "iface", "core";
+			clocks = <&gcc GCC_BLSP1_QUP4_SPI_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
 			pinctrl-names = "default";
 			pinctrl-0 = <&blsp1_spi4_default>;
 			#address-cells = <1>;
@@ -1067,8 +1079,8 @@
 			interrupts = <GIC_SPI 297 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&gcc GCC_BLSP2_UART0_APPS_CLK>, <&gcc GCC_BLSP2_AHB_CLK>;
 			clock-names = "core", "iface";
-			dmas = <&blsp2_dma 1>, <&blsp2_dma 0>;
-			dma-names = "rx", "tx";
+			dmas = <&blsp2_dma 0>, <&blsp2_dma 1>;
+			dma-names = "tx", "rx";
 			pinctrl-names = "default";
 			pinctrl-0 = <&blsp2_uart0_default>;
 			status = "disabled";
@@ -1078,9 +1090,9 @@
 			compatible = "qcom,i2c-qup-v2.2.1";
 			reg = <0x07af5000 0x600>;
 			interrupts = <GIC_SPI 299 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc GCC_BLSP2_AHB_CLK>,
-				 <&gcc GCC_BLSP2_QUP0_I2C_APPS_CLK>;
-			clock-names = "iface", "core";
+			clocks = <&gcc GCC_BLSP2_QUP0_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP2_AHB_CLK>;
+			clock-names = "core", "iface";
 			pinctrl-names = "default";
 			pinctrl-0 = <&blsp2_i2c0_default>;
 			#address-cells = <1>;
@@ -1092,9 +1104,9 @@
 			compatible = "qcom,spi-qup-v2.2.1";
 			reg = <0x07af5000 0x600>;
 			interrupts = <GIC_SPI 299 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&gcc GCC_BLSP2_AHB_CLK>,
-				 <&gcc GCC_BLSP2_QUP0_SPI_APPS_CLK>;
-			clock-names = "iface", "core";
+			clocks = <&gcc GCC_BLSP2_QUP0_SPI_APPS_CLK>,
+				 <&gcc GCC_BLSP2_AHB_CLK>;
+			clock-names = "core", "iface";
 			pinctrl-names = "default";
 			pinctrl-0 = <&blsp2_spi0_default>;
 			#address-cells = <1>;
@@ -1102,8 +1114,8 @@
 			status = "disabled";
 		};
 
-		imem@8600000 {
-			compatible = "simple-mfd";
+		sram@8600000 {
+			compatible = "qcom,qcs404-imem", "syscon", "simple-mfd";
 			reg = <0x08600000 0x1000>;
 
 			#address-cells = <1>;
@@ -1280,7 +1292,7 @@
 		};
 
 		pcie: pci@10000000 {
-			compatible = "qcom,pcie-qcs404", "snps,dw-pcie";
+			compatible = "qcom,pcie-qcs404";
 			reg =  <0x10000000 0xf1d>,
 			       <0x10000f20 0xa8>,
 			       <0x07780000 0x2000>,
diff --git a/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts b/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts
index 845eb7a6bf92..bf8077a1cf9a 100644
--- a/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts
+++ b/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts
@@ -5,6 +5,7 @@
 
 /dts-v1/;
 
+#include <dt-bindings/leds/common.h>
 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
 #include <dt-bindings/sound/qcom,q6afe.h>
 #include <dt-bindings/sound/qcom,q6asm.h>
@@ -29,7 +30,7 @@
 	};
 
 	/* Fixed crystal oscillator dedicated to MCP2518FD */
-	clk40M: can_clock {
+	clk40M: can-clock {
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
 		clock-frequency = <40000000>;
@@ -57,27 +58,32 @@
 	leds {
 		compatible = "gpio-leds";
 
-		user4 {
+		led-user4 {
 			label = "green:user4";
+			function = LED_FUNCTION_INDICATOR;
+			color = <LED_COLOR_ID_GREEN>;
 			gpios = <&pm8150_gpios 10 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "panic-indicator";
 			default-state = "off";
 		};
 
-		wlan {
+		led-wlan {
 			label = "yellow:wlan";
+			function = LED_FUNCTION_WLAN;
+			color = <LED_COLOR_ID_YELLOW>;
 			gpios = <&pm8150_gpios 9 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "phy0tx";
 			default-state = "off";
 		};
 
-		bt {
+		led-bt {
 			label = "blue:bt";
+			function = LED_FUNCTION_BLUETOOTH;
+			color = <LED_COLOR_ID_BLUE>;
 			gpios = <&pm8150_gpios 7 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "bluetooth-power";
 			default-state = "off";
 		};
-
 	};
 
 	lt9611_1v2: lt9611-vdd12-regulator {
@@ -796,7 +802,7 @@
 		"NC",
 		"PM3003A_MODE";
 
-	lt9611_rst_pin: lt9611-rst-pin {
+	lt9611_rst_pin: lt9611-rst-state {
 		pins = "gpio5";
 		function = "normal";
 
@@ -806,6 +812,38 @@
 	};
 };
 
+&pm8150l_lpg {
+	status = "okay";
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	led@1 {
+		reg = <1>;
+		color = <LED_COLOR_ID_GREEN>;
+		function = LED_FUNCTION_HEARTBEAT;
+		function-enumerator = <3>;
+
+		linux,default-trigger = "heartbeat";
+		default-state = "on";
+	};
+
+	led@2 {
+		reg = <2>;
+		color = <LED_COLOR_ID_GREEN>;
+		function = LED_FUNCTION_INDICATOR;
+		function-enumerator = <2>;
+		default-state = "on";
+	};
+
+	led@3 {
+		reg = <3>;
+		color = <LED_COLOR_ID_GREEN>;
+		function = LED_FUNCTION_INDICATOR;
+		function-enumerator = <1>;
+	};
+};
+
 &pon_pwrkey {
 	status = "okay";
 };
@@ -830,7 +868,7 @@
 
 &q6afedai {
 	qi2s@16 {
-		reg = <16>;
+		reg = <PRIMARY_MI2S_RX>;
 		qcom,sd-lines = <0 1 2 3>;
 	};
 };
@@ -838,7 +876,7 @@
 /* TERT I2S Uses 1 I2S SD Lines for audio on LT9611 HDMI Bridge */
 &q6afedai {
 	qi2s@20 {
-		reg = <20>;
+		reg = <TERTIARY_MI2S_RX>;
 		qcom,sd-lines = <0>;
 	};
 };
@@ -915,7 +953,7 @@
 		};
 
 		codec {
-			sound-dai =  <&lt9611_codec 0>;
+			sound-dai = <&lt9611_codec 0>;
 		};
 	};
 
diff --git a/arch/arm64/boot/dts/qcom/sa8155p-adp.dts b/arch/arm64/boot/dts/qcom/sa8155p-adp.dts
index 8756c2b25c7e..87ab0e1ecd16 100644
--- a/arch/arm64/boot/dts/qcom/sa8155p-adp.dts
+++ b/arch/arm64/boot/dts/qcom/sa8155p-adp.dts
@@ -47,6 +47,29 @@
 
 		vin-supply = <&vreg_3p3>;
 	};
+
+	mtl_rx_setup: rx-queues-config {
+		snps,rx-queues-to-use = <1>;
+		snps,rx-sched-sp;
+
+		queue0 {
+			snps,dcb-algorithm;
+			snps,map-to-dma-channel = <0x0>;
+			snps,route-up;
+			snps,priority = <0x1>;
+		};
+	};
+
+	mtl_tx_setup: tx-queues-config {
+		snps,tx-queues-to-use = <1>;
+		snps,tx-sched-wrr;
+
+		queue0 {
+			snps,weight = <0x10>;
+			snps,dcb-algorithm;
+			snps,priority = <0x0>;
+		};
+	};
 };
 
 &apps_rsc {
@@ -303,6 +326,41 @@
 	};
 };
 
+&ethernet {
+	status = "okay";
+
+	snps,reset-gpio = <&tlmm 79 GPIO_ACTIVE_LOW>;
+	snps,reset-active-low;
+	snps,reset-delays-us = <0 11000 70000>;
+
+	snps,mtl-rx-config = <&mtl_rx_setup>;
+	snps,mtl-tx-config = <&mtl_tx_setup>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&ethernet_defaults>;
+
+	phy-handle = <&rgmii_phy>;
+	phy-mode = "rgmii";
+	max-speed = <1000>;
+
+	mdio {
+		#address-cells = <0x1>;
+		#size-cells = <0x0>;
+
+		compatible = "snps,dwmac-mdio";
+
+		/* Micrel KSZ9031RNZ PHY */
+		rgmii_phy: phy@7 {
+			reg = <0x7>;
+
+			interrupt-parent = <&tlmm>;
+			interrupts-extended = <&tlmm 124 IRQ_TYPE_EDGE_FALLING>; /* phy intr */
+			device_type = "ethernet-phy";
+			compatible = "ethernet-phy-ieee802.3-c22";
+		};
+	};
+};
+
 &qupv3_id_1 {
 	status = "okay";
 };
@@ -317,6 +375,20 @@
 	firmware-name = "qcom/sa8155p/cdsp.mdt";
 };
 
+&sdhc_2 {
+	status = "okay";
+
+	cd-gpios = <&tlmm 4 GPIO_ACTIVE_LOW>;
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sdc2_on>;
+	pinctrl-1 = <&sdc2_off>;
+	vqmmc-supply = <&vreg_l13c_2p96>; /* IO line power */
+	vmmc-supply = <&vreg_l17a_2p96>;  /* Card power line */
+	bus-width = <4>;
+	no-sdio;
+	no-emmc;
+};
+
 &uart2 {
 	status = "okay";
 };
@@ -387,9 +459,78 @@
 	vdda-pll-supply = <&vdda_usb_ss_dp_core_1>;
 };
 
+&pcie0 {
+	status = "okay";
+};
+
+&pcie0_phy {
+	status = "okay";
+	vdda-phy-supply = <&vreg_l18c_0p88>;
+	vdda-pll-supply = <&vreg_l8c_1p2>;
+};
+
+&pcie1_phy {
+	vdda-phy-supply = <&vreg_l18c_0p88>;
+	vdda-pll-supply = <&vreg_l8c_1p2>;
+};
+
 &tlmm {
 	gpio-reserved-ranges = <0 4>;
 
+	sdc2_on: sdc2_on {
+		clk {
+			pins = "sdc2_clk";
+			bias-disable;		/* No pull */
+			drive-strength = <16>;	/* 16 MA */
+		};
+
+		cmd {
+			pins = "sdc2_cmd";
+			bias-pull-up;		/* pull up */
+			drive-strength = <16>;	/* 16 MA */
+		};
+
+		data {
+			pins = "sdc2_data";
+			bias-pull-up;		/* pull up */
+			drive-strength = <16>;	/* 16 MA */
+		};
+
+		sd-cd {
+			pins = "gpio96";
+			function = "gpio";
+			bias-pull-up;		/* pull up */
+			drive-strength = <2>;	/* 2 MA */
+		};
+	};
+
+	sdc2_off: sdc2_off {
+		clk {
+			pins = "sdc2_clk";
+			bias-disable;		/* No pull */
+			drive-strength = <2>;	/* 2 MA */
+		};
+
+		cmd {
+			pins = "sdc2_cmd";
+			bias-pull-up;		/* pull up */
+			drive-strength = <2>;	/* 2 MA */
+		};
+
+		data {
+			pins = "sdc2_data";
+			bias-pull-up;		/* pull up */
+			drive-strength = <2>;	/* 2 MA */
+		};
+
+		sd-cd {
+			pins = "gpio96";
+			function = "gpio";
+			bias-pull-up;		/* pull up */
+			drive-strength = <2>;	/* 2 MA */
+		};
+	};
+
 	usb2phy_ac_en1_default: usb2phy_ac_en1_default {
 		mux {
 			pins = "gpio113";
@@ -407,4 +548,53 @@
 			drive-strength = <2>;
 		};
 	};
+
+	ethernet_defaults: ethernet-defaults {
+		mdc {
+			pins = "gpio7";
+			function = "rgmii";
+			bias-pull-up;
+		};
+
+		mdio {
+			pins = "gpio59";
+			function = "rgmii";
+			bias-pull-up;
+		};
+
+		rgmii-rx {
+			pins = "gpio117", "gpio118", "gpio119", "gpio120", "gpio115", "gpio116";
+			function = "rgmii";
+			bias-disable;
+			drive-strength = <2>;
+		};
+
+		rgmii-tx {
+			pins = "gpio122", "gpio4", "gpio5", "gpio6", "gpio114", "gpio121";
+			function = "rgmii";
+			bias-pull-up;
+			drive-strength = <16>;
+		};
+
+		phy-intr {
+			pins = "gpio124";
+			function = "emac_phy";
+			bias-disable;
+			drive-strength = <8>;
+		};
+
+		pps {
+			pins = "gpio81";
+			function = "emac_pps";
+			bias-disable;
+			drive-strength = <8>;
+		};
+
+		phy-reset {
+			pins = "gpio79";
+			function = "gpio";
+			bias-pull-up;
+			drive-strength = <16>;
+		};
+	};
 };
diff --git a/arch/arm64/boot/dts/qcom/sa8295p-adp.dts b/arch/arm64/boot/dts/qcom/sa8295p-adp.dts
new file mode 100644
index 000000000000..b608b82dff03
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sa8295p-adp.dts
@@ -0,0 +1,382 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2022, Linaro Limited
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+#include <dt-bindings/spmi/spmi.h>
+
+#include "sa8540p.dtsi"
+
+/ {
+	model = "Qualcomm SA8295P ADP";
+	compatible = "qcom,sa8295p-adp", "qcom,sa8540p";
+
+	aliases {
+		serial0 = &qup2_uart17;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
+
+&apps_rsc {
+	pmm8540-a-regulators {
+		compatible = "qcom,pm8150-rpmh-regulators";
+		qcom,pmic-id = "a";
+
+		vreg_l3a: ldo3 {
+			regulator-name = "vreg_l3a";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1208000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l5a: ldo5 {
+			regulator-name = "vreg_l5a";
+			regulator-min-microvolt = <912000>;
+			regulator-max-microvolt = <912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l7a: ldo7 {
+			regulator-name = "vreg_l7a";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l13a: ldo13 {
+			regulator-name = "vreg_l13a";
+			regulator-min-microvolt = <3072000>;
+			regulator-max-microvolt = <3072000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	pmm8540-c-regulators {
+		compatible = "qcom,pm8150-rpmh-regulators";
+		qcom,pmic-id = "c";
+
+		vreg_l1c: ldo1 {
+			regulator-name = "vreg_l1c";
+			regulator-min-microvolt = <912000>;
+			regulator-max-microvolt = <912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2c: ldo2 {
+			regulator-name = "vreg_l2c";
+			regulator-min-microvolt = <3072000>;
+			regulator-max-microvolt = <3072000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3c: ldo3 {
+			regulator-name = "vreg_l3c";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l4c: ldo4 {
+			regulator-name = "vreg_l4c";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1208000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l6c: ldo6 {
+			regulator-name = "vreg_l6c";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l7c: ldo7 {
+			regulator-name = "vreg_l7c";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l10c: ldo10 {
+			regulator-name = "vreg_l10c";
+			regulator-min-microvolt = <2504000>;
+			regulator-max-microvolt = <2504000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l17c: ldo17 {
+			regulator-name = "vreg_l17c";
+			regulator-min-microvolt = <2504000>;
+			regulator-max-microvolt = <2504000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+		};
+	};
+
+	pmm8540-g-regulators {
+		compatible = "qcom,pm8150-rpmh-regulators";
+		qcom,pmic-id = "g";
+
+		vreg_l3g: ldo3 {
+			regulator-name = "vreg_l3g";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l7g: ldo7 {
+			regulator-name = "vreg_l7g";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l8g: ldo8 {
+			regulator-name = "vreg_l8g";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <880000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+};
+
+&qup2 {
+	status = "okay";
+};
+
+&qup2_uart17 {
+	compatible = "qcom,geni-debug-uart";
+	status = "okay";
+};
+
+&remoteproc_adsp {
+	firmware-name = "qcom/sa8540p/adsp.mbn";
+	status = "okay";
+};
+
+&remoteproc_nsp0 {
+	firmware-name = "qcom/sa8540p/cdsp.mbn";
+	status = "okay";
+};
+
+&remoteproc_nsp1 {
+	firmware-name = "qcom/sa8540p/cdsp1.mbn";
+	status = "okay";
+};
+
+&spmi_bus {
+	pm8450a: pmic@0 {
+		compatible = "qcom,pm8150", "qcom,spmi-pmic";
+		reg = <0x0 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pm8450a_gpios: gpio@c000 {
+			compatible = "qcom,pm8150-gpio", "qcom,spmi-gpio";
+			reg = <0xc000>;
+			gpio-controller;
+			gpio-ranges = <&pm8450a_gpios 0 0 10>;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	pm8450c: pmic@4 {
+		compatible = "qcom,pm8150", "qcom,spmi-pmic";
+		reg = <0x4 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pm8450c_gpios: gpio@c000 {
+			compatible = "qcom,pm8150-gpio", "qcom,spmi-gpio";
+			reg = <0xc000>;
+			gpio-controller;
+			gpio-ranges = <&pm8450c_gpios 0 0 10>;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	pm8450e: pmic@8 {
+		compatible = "qcom,pm8150", "qcom,spmi-pmic";
+		reg = <0x8 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pm8450e_gpios: gpio@c000 {
+			compatible = "qcom,pm8150-gpio", "qcom,spmi-gpio";
+			reg = <0xc000>;
+			gpio-controller;
+			gpio-ranges = <&pm8450e_gpios 0 0 10>;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	pm8450g: pmic@c {
+		compatible = "qcom,pm8150", "qcom,spmi-pmic";
+		reg = <0xc SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pm8450g_gpios: gpio@c000 {
+			compatible = "qcom,pm8150-gpio", "qcom,spmi-gpio";
+			reg = <0xc000>;
+			gpio-controller;
+			gpio-ranges = <&pm8450g_gpios 0 0 10>;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+};
+
+&ufs_mem_hc {
+	reset-gpios = <&tlmm 228 GPIO_ACTIVE_LOW>;
+
+	vcc-supply = <&vreg_l17c>;
+	vcc-max-microamp = <800000>;
+	vccq-supply = <&vreg_l6c>;
+	vccq-max-microamp = <900000>;
+
+	status = "okay";
+};
+
+&ufs_mem_phy {
+	vdda-phy-supply = <&vreg_l8g>;
+	vdda-pll-supply = <&vreg_l3g>;
+
+	status = "okay";
+};
+
+&ufs_card_hc {
+	reset-gpios = <&tlmm 229 GPIO_ACTIVE_LOW>;
+
+	vcc-supply = <&vreg_l10c>;
+	vcc-max-microamp = <800000>;
+	vccq-supply = <&vreg_l3c>;
+	vccq-max-microamp = <900000>;
+
+	status = "okay";
+};
+
+&ufs_card_phy {
+	vdda-phy-supply = <&vreg_l8g>;
+	vdda-pll-supply = <&vreg_l3g>;
+
+	status = "okay";
+};
+
+&usb_0 {
+	status = "okay";
+};
+
+&usb_0_dwc3 {
+	/* TODO: Define USB-C connector properly */
+	dr_mode = "peripheral";
+};
+
+&usb_0_hsphy {
+	vdda-pll-supply = <&vreg_l5a>;
+	vdda18-supply = <&vreg_l7a>;
+	vdda33-supply = <&vreg_l13a>;
+
+	status = "okay";
+};
+
+&usb_0_qmpphy {
+	vdda-phy-supply = <&vreg_l3a>;
+	vdda-pll-supply = <&vreg_l5a>;
+
+	status = "okay";
+};
+
+&usb_1 {
+	status = "okay";
+};
+
+&usb_1_dwc3 {
+	/* TODO: Define USB-C connector properly */
+	dr_mode = "host";
+};
+
+&usb_1_hsphy {
+	vdda-pll-supply = <&vreg_l1c>;
+	vdda18-supply = <&vreg_l7c>;
+	vdda33-supply = <&vreg_l2c>;
+
+	status = "okay";
+};
+
+&usb_1_qmpphy {
+	vdda-phy-supply = <&vreg_l4c>;
+	vdda-pll-supply = <&vreg_l1c>;
+
+	status = "okay";
+};
+
+&usb_2_hsphy0 {
+	vdda-pll-supply = <&vreg_l5a>;
+	vdda18-supply = <&vreg_l7g>;
+	vdda33-supply = <&vreg_l13a>;
+
+	status = "okay";
+};
+
+&usb_2_hsphy1 {
+	vdda-pll-supply = <&vreg_l5a>;
+	vdda18-supply = <&vreg_l7g>;
+	vdda33-supply = <&vreg_l13a>;
+
+	status = "okay";
+};
+
+&usb_2_hsphy2 {
+	vdda-pll-supply = <&vreg_l5a>;
+	vdda18-supply = <&vreg_l7g>;
+	vdda33-supply = <&vreg_l13a>;
+
+	status = "okay";
+};
+
+&usb_2_hsphy3 {
+	vdda-pll-supply = <&vreg_l5a>;
+	vdda18-supply = <&vreg_l7g>;
+	vdda33-supply = <&vreg_l13a>;
+
+	status = "okay";
+};
+
+&usb_2_qmpphy0 {
+	vdda-phy-supply = <&vreg_l3a>;
+	vdda-pll-supply = <&vreg_l5a>;
+
+	status = "okay";
+};
+
+&usb_2_qmpphy1 {
+	vdda-phy-supply = <&vreg_l3a>;
+	vdda-pll-supply = <&vreg_l5a>;
+
+	status = "okay";
+};
+
+&xo_board_clk {
+	clock-frequency = <38400000>;
+};
+
+/* PINCTRL */
diff --git a/arch/arm64/boot/dts/qcom/sa8540p.dtsi b/arch/arm64/boot/dts/qcom/sa8540p.dtsi
new file mode 100644
index 000000000000..8ea2886fbab2
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sa8540p.dtsi
@@ -0,0 +1,133 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2022, Linaro Limited
+ */
+
+#include "sc8280xp.dtsi"
+
+/delete-node/ &cpu0_opp_table;
+/delete-node/ &cpu4_opp_table;
+
+/ {
+	cpu0_opp_table: cpu0-opp-table {
+		compatible = "operating-points-v2";
+		opp-shared;
+
+		opp-403200000 {
+			opp-hz = /bits/ 64 <403200000>;
+		};
+		opp-499200000 {
+			opp-hz = /bits/ 64 <499200000>;
+		};
+		opp-595200000 {
+			opp-hz = /bits/ 64 <595200000>;
+		};
+		opp-710400000 {
+			opp-hz = /bits/ 64 <710400000>;
+		};
+		opp-806400000 {
+			opp-hz = /bits/ 64 <806400000>;
+		};
+		opp-902400000 {
+			opp-hz = /bits/ 64 <902400000>;
+		};
+		opp-1017600000 {
+			opp-hz = /bits/ 64 <1017600000>;
+		};
+		opp-1113600000 {
+			opp-hz = /bits/ 64 <1113600000>;
+		};
+		opp-1209600000 {
+			opp-hz = /bits/ 64 <1209600000>;
+		};
+		opp-1324800000 {
+			opp-hz = /bits/ 64 <1324800000>;
+		};
+		opp-1440000000 {
+			opp-hz = /bits/ 64 <1440000000>;
+		};
+		opp-1555200000 {
+			opp-hz = /bits/ 64 <1555200000>;
+		};
+		opp-1670400000 {
+			opp-hz = /bits/ 64 <1670400000>;
+		};
+		opp-1785600000 {
+			opp-hz = /bits/ 64 <1785600000>;
+		};
+		opp-1881600000 {
+			opp-hz = /bits/ 64 <1881600000>;
+		};
+		opp-2016000000 {
+			opp-hz = /bits/ 64 <2016000000>;
+		};
+		opp-2131200000 {
+			opp-hz = /bits/ 64 <2131200000>;
+		};
+		opp-2246400000 {
+			opp-hz = /bits/ 64 <2246400000>;
+		};
+	};
+
+	cpu4_opp_table: cpu4-opp-table {
+		compatible = "operating-points-v2";
+		opp-shared;
+
+		opp-825600000 {
+			opp-hz = /bits/ 64 <825600000>;
+		};
+		opp-940800000 {
+			opp-hz = /bits/ 64 <940800000>;
+		};
+		opp-1056000000 {
+			opp-hz = /bits/ 64 <1056000000>;
+		};
+		opp-1171200000 {
+			opp-hz = /bits/ 64 <1171200000>;
+		};
+		opp-1286400000 {
+			opp-hz = /bits/ 64 <1286400000>;
+		};
+		opp-1401600000 {
+			opp-hz = /bits/ 64 <1401600000>;
+		};
+		opp-1516800000 {
+			opp-hz = /bits/ 64 <1516800000>;
+		};
+		opp-1632000000 {
+			opp-hz = /bits/ 64 <1632000000>;
+		};
+		opp-1747200000 {
+			opp-hz = /bits/ 64 <1747200000>;
+		};
+		opp-1862400000 {
+			opp-hz = /bits/ 64 <1862400000>;
+		};
+		opp-1977600000 {
+			opp-hz = /bits/ 64 <1977600000>;
+		};
+		opp-2073600000 {
+			opp-hz = /bits/ 64 <2073600000>;
+		};
+		opp-2169600000 {
+			opp-hz = /bits/ 64 <2169600000>;
+		};
+		opp-2284800000 {
+			opp-hz = /bits/ 64 <2284800000>;
+		};
+		opp-2380800000 {
+			opp-hz = /bits/ 64 <2380800000>;
+		};
+		opp-2496000000 {
+			opp-hz = /bits/ 64 <2496000000>;
+		};
+		opp-2592000000 {
+			opp-hz = /bits/ 64 <2592000000>;
+		};
+	};
+};
+
+&rpmhpd {
+	compatible = "qcom,sa8540p-rpmhpd";
+};
diff --git a/arch/arm64/boot/dts/qcom/sc7180-idp.dts b/arch/arm64/boot/dts/qcom/sc7180-idp.dts
index acdb36f4479f..9dee131b1e24 100644
--- a/arch/arm64/boot/dts/qcom/sc7180-idp.dts
+++ b/arch/arm64/boot/dts/qcom/sc7180-idp.dts
@@ -330,6 +330,7 @@
 
 &dsi_phy {
 	status = "okay";
+	vdds-supply = <&vreg_l4a_0p8>;
 };
 
 &mdp {
@@ -389,7 +390,7 @@
 	pinctrl-names = "default","sleep";
 	pinctrl-0 = <&sdc2_on>;
 	pinctrl-1 = <&sdc2_off>;
-	vmmc-supply  = <&vreg_l9c_2p9>;
+	vmmc-supply = <&vreg_l9c_2p9>;
 	vqmmc-supply = <&vreg_l6c_2p9>;
 
 	cd-gpios = <&tlmm 69 GPIO_ACTIVE_LOW>;
@@ -467,7 +468,7 @@
 /* PINCTRL - additions to nodes defined in sc7180.dtsi */
 
 &pm6150l_gpio {
-	disp_pins: disp-pins {
+	disp_pins: disp-state {
 		pinconf {
 			pins = "gpio3";
 			function = PMIC_GPIO_FUNC_FUNC1;
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-coachz-r1.dts b/arch/arm64/boot/dts/qcom/sc7180-trogdor-coachz-r1.dts
index 8290d036044a..edfcd47e1a00 100644
--- a/arch/arm64/boot/dts/qcom/sc7180-trogdor-coachz-r1.dts
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-coachz-r1.dts
@@ -24,8 +24,6 @@
 };
 
 &pm6150_adc {
-	status = "disabled";
-
 	/delete-node/ skin-temp-thermistor@4e;
 	/delete-node/ charger-thermistor@4f;
 };
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-coachz.dtsi b/arch/arm64/boot/dts/qcom/sc7180-trogdor-coachz.dtsi
index 14ed09f30a73..7ee407f7b6bb 100644
--- a/arch/arm64/boot/dts/qcom/sc7180-trogdor-coachz.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-coachz.dtsi
@@ -5,15 +5,10 @@
  * Copyright 2020 Google LLC.
  */
 
-#include "sc7180.dtsi"
-
-ap_ec_spi: &spi6 {};
-ap_h1_spi: &spi0 {};
-
 #include "sc7180-trogdor.dtsi"
 #include "sc7180-trogdor-ti-sn65dsi86.dtsi"
 
-/* Deleted nodes from trogdor.dtsi */
+/* Deleted nodes from sc7180-trogdor.dtsi */
 
 /delete-node/ &alc5682;
 /delete-node/ &pp3300_codec;
@@ -86,6 +81,10 @@ ap_h1_spi: &spi0 {};
 };
 
 &cros_ec {
+	keyboard-controller {
+		compatible = "google,cros-ec-keyb-switches";
+	};
+
 	cros_ec_proximity: proximity {
 		compatible = "google,cros-ec-mkbp-proximity";
 		label = "proximity-wifi";
@@ -111,10 +110,6 @@ ap_ts_pen_1v8: &i2c4 {
 	};
 };
 
-&i2c7 {
-	status = "disabled";
-};
-
 &i2c9 {
 	status = "disabled";
 };
@@ -142,6 +137,22 @@ ap_ts_pen_1v8: &i2c4 {
 	};
 };
 
+&pp1800_uf_cam {
+	status = "okay";
+};
+
+&pp1800_wf_cam {
+	status = "okay";
+};
+
+&pp2800_uf_cam {
+	status = "okay";
+};
+
+&pp2800_wf_cam {
+	status = "okay";
+};
+
 &pp3300_dx_edp {
 	gpio = <&tlmm 67 GPIO_ACTIVE_HIGH>;
 };
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-homestar-r2.dts b/arch/arm64/boot/dts/qcom/sc7180-trogdor-homestar-r2.dts
index db6c2da67cea..d9e905ed4e62 100644
--- a/arch/arm64/boot/dts/qcom/sc7180-trogdor-homestar-r2.dts
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-homestar-r2.dts
@@ -7,6 +7,8 @@
 
 /dts-v1/;
 
+#include "sc7180-trogdor.dtsi"
+#include "sc7180-trogdor-ti-sn65dsi86.dtsi"
 #include "sc7180-trogdor-homestar.dtsi"
 
 / {
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-homestar-r3.dts b/arch/arm64/boot/dts/qcom/sc7180-trogdor-homestar-r3.dts
index 3fd8aa5bb7a6..242c178fdc52 100644
--- a/arch/arm64/boot/dts/qcom/sc7180-trogdor-homestar-r3.dts
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-homestar-r3.dts
@@ -7,9 +7,11 @@
 
 /dts-v1/;
 
+#include "sc7180-trogdor.dtsi"
+#include "sc7180-trogdor-ti-sn65dsi86.dtsi"
 #include "sc7180-trogdor-homestar.dtsi"
 
 / {
-	model = "Google Homestar (rev3+)";
-	compatible = "google,homestar", "qcom,sc7180";
+	model = "Google Homestar (rev3)";
+	compatible = "google,homestar-rev3", "qcom,sc7180";
 };
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-homestar-r4.dts b/arch/arm64/boot/dts/qcom/sc7180-trogdor-homestar-r4.dts
new file mode 100644
index 000000000000..66dd87016201
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-homestar-r4.dts
@@ -0,0 +1,21 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Google Homestar board device tree source
+ *
+ * Copyright 2021 Google LLC.
+ */
+
+/dts-v1/;
+
+#include "sc7180-trogdor.dtsi"
+#include "sc7180-trogdor-parade-ps8640.dtsi"
+#include "sc7180-trogdor-homestar.dtsi"
+
+/ {
+	model = "Google Homestar (rev4+)";
+	compatible = "google,homestar", "qcom,sc7180";
+};
+
+&pp3300_brij_ps8640 {
+	regulator-enable-ramp-delay = <4000>;
+};
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-homestar.dtsi b/arch/arm64/boot/dts/qcom/sc7180-trogdor-homestar.dtsi
index 4ab890b2a1d4..1bd6c7dcd9e9 100644
--- a/arch/arm64/boot/dts/qcom/sc7180-trogdor-homestar.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-homestar.dtsi
@@ -5,13 +5,7 @@
  * Copyright 2021 Google LLC.
  */
 
-#include "sc7180.dtsi"
-
-ap_ec_spi: &spi6 {};
-ap_h1_spi: &spi0 {};
-
-#include "sc7180-trogdor.dtsi"
-#include "sc7180-trogdor-ti-sn65dsi86.dtsi"
+/* This file must be included after sc7180-trogdor.dtsi */
 
 / {
 	/* BOARD-SPECIFIC TOP LEVEL NODES */
@@ -91,10 +85,6 @@ ap_h1_spi: &spi0 {};
 	};
 };
 
-&ap_tp_i2c {
-	status = "disabled";
-};
-
 ap_ts_pen_1v8: &i2c4 {
 	status = "okay";
 	clock-frequency = <400000>;
@@ -124,6 +114,12 @@ ap_ts_pen_1v8: &i2c4 {
 	status = "okay";
 };
 
+&cros_ec {
+	keyboard-controller {
+		compatible = "google,cros-ec-keyb-switches";
+	};
+};
+
 &panel {
 	compatible = "samsung,atna33xc20";
 	enable-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>;
@@ -149,6 +145,22 @@ ap_ts_pen_1v8: &i2c4 {
 	};
 };
 
+&pp1800_uf_cam {
+	status = "okay";
+};
+
+&pp1800_wf_cam {
+	status = "okay";
+};
+
+&pp2800_uf_cam {
+	status = "okay";
+};
+
+&pp2800_wf_cam {
+	status = "okay";
+};
+
 &pp3300_dx_edp {
 	gpio = <&tlmm 67 GPIO_ACTIVE_HIGH>;
 };
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-kingoftown-r0.dts b/arch/arm64/boot/dts/qcom/sc7180-trogdor-kingoftown-r0.dts
new file mode 100644
index 000000000000..1a62e8d435ab
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-kingoftown-r0.dts
@@ -0,0 +1,44 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Google Kingoftown board device tree source
+ *
+ * Copyright 2021 Google LLC.
+ */
+
+/dts-v1/;
+
+#include "sc7180-trogdor.dtsi"
+#include "sc7180-trogdor-ti-sn65dsi86.dtsi"
+#include "sc7180-trogdor-kingoftown.dtsi"
+
+/ {
+	model = "Google Kingoftown (rev0)";
+	compatible = "google,kingoftown-rev0", "qcom,sc7180";
+};
+
+/*
+ * In rev1+, the enable pin of pp3300_fp_tp will be tied to pp1800_l10a
+ * power rail instead, since kingoftown does not have FP.
+ */
+&pp3300_fp_tp {
+	gpio = <&tlmm 74 GPIO_ACTIVE_HIGH>;
+	enable-active-high;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&en_fp_rails>;
+};
+
+&tlmm {
+	en_fp_rails: en-fp-rails {
+		pinmux {
+			pins = "gpio74";
+			function = "gpio";
+		};
+
+		pinconf {
+			pins = "gpio74";
+			drive-strength = <2>;
+			bias-disable;
+		};
+	};
+};
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-kingoftown-r1.dts b/arch/arm64/boot/dts/qcom/sc7180-trogdor-kingoftown-r1.dts
new file mode 100644
index 000000000000..e0752ba7df11
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-kingoftown-r1.dts
@@ -0,0 +1,17 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Google Kingoftown board device tree source
+ *
+ * Copyright 2021 Google LLC.
+ */
+
+/dts-v1/;
+
+#include "sc7180-trogdor.dtsi"
+#include "sc7180-trogdor-parade-ps8640.dtsi"
+#include "sc7180-trogdor-kingoftown.dtsi"
+
+/ {
+	model = "Google Kingoftown (rev1+)";
+	compatible = "google,kingoftown", "qcom,sc7180";
+};
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-kingoftown.dtsi b/arch/arm64/boot/dts/qcom/sc7180-trogdor-kingoftown.dtsi
new file mode 100644
index 000000000000..74f0e07ea5cf
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-kingoftown.dtsi
@@ -0,0 +1,225 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Google Kingoftown board device tree source
+ *
+ * Copyright 2021 Google LLC.
+ */
+
+/* This file must be included after sc7180-trogdor.dtsi */
+#include <arm/cros-ec-keyboard.dtsi>
+#include "sc7180-trogdor-lte-sku.dtsi"
+
+&alc5682 {
+	compatible = "realtek,rt5682s";
+	realtek,dmic1-clk-pin = <2>;
+	realtek,dmic-clk-rate-hz = <2048000>;
+};
+
+&ap_tp_i2c {
+	status = "okay";
+};
+
+ap_ts_pen_1v8: &i2c4 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	ap_ts: touchscreen@10 {
+		compatible = "elan,ekth3500";
+		reg = <0x10>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&ts_int_l>, <&ts_reset_l>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <9 IRQ_TYPE_LEVEL_LOW>;
+
+		vcc33-supply = <&pp3300_ts>;
+
+		reset-gpios = <&tlmm 8 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&keyboard_controller {
+	function-row-physmap = <
+		MATRIX_KEY(0x00, 0x02, 0)       /* T1 */
+		MATRIX_KEY(0x03, 0x02, 0)       /* T2 */
+		MATRIX_KEY(0x02, 0x02, 0)       /* T3 */
+		MATRIX_KEY(0x01, 0x02, 0)       /* T4 */
+		MATRIX_KEY(0x03, 0x04, 0)       /* T5 */
+		MATRIX_KEY(0x02, 0x04, 0)       /* T6 */
+		MATRIX_KEY(0x01, 0x04, 0)       /* T7 */
+		MATRIX_KEY(0x02, 0x09, 0)       /* T8 */
+		MATRIX_KEY(0x01, 0x09, 0)       /* T9 */
+		MATRIX_KEY(0x00, 0x04, 0)       /* T10 */
+	>;
+	linux,keymap = <
+		MATRIX_KEY(0x00, 0x02, KEY_BACK)
+		MATRIX_KEY(0x03, 0x02, KEY_REFRESH)
+		MATRIX_KEY(0x02, 0x02, KEY_ZOOM)
+		MATRIX_KEY(0x01, 0x02, KEY_SCALE)
+		MATRIX_KEY(0x03, 0x04, KEY_SYSRQ)
+		MATRIX_KEY(0x02, 0x04, KEY_BRIGHTNESSDOWN)
+		MATRIX_KEY(0x01, 0x04, KEY_BRIGHTNESSUP)
+		MATRIX_KEY(0x02, 0x09, KEY_MUTE)
+		MATRIX_KEY(0x01, 0x09, KEY_VOLUMEDOWN)
+		MATRIX_KEY(0x00, 0x04, KEY_VOLUMEUP)
+
+		CROS_STD_MAIN_KEYMAP
+	>;
+};
+
+&panel {
+	compatible = "edp-panel";
+};
+
+&pp3300_dx_edp {
+	gpio = <&tlmm 67 GPIO_ACTIVE_HIGH>;
+};
+
+&sound {
+	compatible = "google,sc7180-trogdor";
+	model = "sc7180-rt5682s-max98357a-1mic";
+};
+
+&wifi {
+	qcom,ath10k-calibration-variant = "GO_KINGOFTOWN";
+};
+
+/* PINCTRL - modifications to sc7180-trogdor.dtsi */
+
+&en_pp3300_dx_edp {
+	pinmux {
+		pins = "gpio67";
+	};
+
+	pinconf {
+		pins = "gpio67";
+	};
+};
+
+/* PINCTRL - board-specific pinctrl */
+
+&tlmm {
+	gpio-line-names = "TP_INT_L",		/* 0 */
+			  "AP_RAM_ID0",
+			  "AP_SKU_ID2",
+			  "AP_RAM_ID1",
+			  "",
+			  "AP_RAM_ID2",
+			  "AP_TP_I2C_SDA",
+			  "AP_TP_I2C_SCL",
+			  "TS_RESET_L",
+			  "TS_INT_L",
+			  "",			/* 10 */
+			  "EDP_BRIJ_IRQ",
+			  "AP_EDP_BKLTEN",
+			  "",
+			  "",
+			  "EDP_BRIJ_I2C_SDA",
+			  "EDP_BRIJ_I2C_SCL",
+			  "HUB_RST_L",
+			  "",
+			  "",
+			  "",			/* 20 */
+			  "",
+			  "",
+			  "AMP_EN",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "HP_IRQ",
+			  "",
+			  "",			/* 30 */
+			  "AP_BRD_ID2",
+			  "BRIJ_SUSPEND",
+			  "AP_BRD_ID0",
+			  "AP_H1_SPI_MISO",
+			  "AP_H1_SPI_MOSI",
+			  "AP_H1_SPI_CLK",
+			  "AP_H1_SPI_CS_L",
+			  "BT_UART_CTS",
+			  "BT_UART_RTS",
+			  "BT_UART_TXD",	/* 40 */
+			  "BT_UART_RXD",
+			  "H1_AP_INT_ODL",
+			  "",
+			  "UART_AP_TX_DBG_RX",
+			  "UART_DBG_TX_AP_RX",
+			  "HP_I2C_SDA",
+			  "HP_I2C_SCL",
+			  "FORCED_USB_BOOT",
+			  "AMP_BCLK",
+			  "AMP_LRCLK",		/* 50 */
+			  "AMP_DIN",
+			  "",
+			  "HP_BCLK",
+			  "HP_LRCLK",
+			  "HP_DOUT",
+			  "HP_DIN",
+			  "HP_MCLK",
+			  "AP_SKU_ID0",
+			  "AP_EC_SPI_MISO",
+			  "AP_EC_SPI_MOSI",	/* 60 */
+			  "AP_EC_SPI_CLK",
+			  "AP_EC_SPI_CS_L",
+			  "AP_SPI_CLK",
+			  "AP_SPI_MOSI",
+			  "AP_SPI_MISO",
+			  /*
+			   * AP_FLASH_WP_L is crossystem ABI. Schematics
+			   * call it BIOS_FLASH_WP_L.
+			   */
+			  "AP_FLASH_WP_L",
+			  "EN_PP3300_DX_EDP",
+			  "AP_SPI_CS0_L",
+			  "",
+			  "",			/* 70 */
+			  "",
+			  "",
+			  "",
+			  "EN_FP_RAILS",
+			  "UIM2_DATA",
+			  "UIM2_CLK",
+			  "UIM2_RST",
+			  "UIM2_PRESENT_L",
+			  "UIM1_DATA",
+			  "UIM1_CLK",		/* 80 */
+			  "UIM1_RST",
+			  "",
+			  "CODEC_PWR_EN",
+			  "HUB_EN",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "AP_SKU_ID1",		/* 90 */
+			  "AP_RST_REQ",
+			  "",
+			  "AP_BRD_ID1",
+			  "AP_EC_INT_L",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",			/* 100 */
+			  "",
+			  "",
+			  "",
+			  "EDP_BRIJ_EN",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",			/* 110 */
+			  "",
+			  "",
+			  "",
+			  "",
+			  "AP_TS_PEN_I2C_SDA",
+			  "AP_TS_PEN_I2C_SCL",
+			  "DP_HOT_PLUG_DET",
+			  "EC_IN_RW_ODL";
+};
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-limozeen-nots-r4.dts b/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-limozeen-nots-r4.dts
index 6ebde0828550..850776c5323d 100644
--- a/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-limozeen-nots-r4.dts
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-limozeen-nots-r4.dts
@@ -5,7 +5,7 @@
  * Copyright 2020 Google LLC.
  */
 
-#include "sc7180-trogdor-lazor-limozeen-nots.dts"
+#include "sc7180-trogdor-lazor-limozeen-nots-r5.dts"
 
 / {
 	model = "Google Lazor Limozeen without Touchscreen (rev4)";
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-limozeen-nots-r5.dts b/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-limozeen-nots-r5.dts
new file mode 100644
index 000000000000..235cda2bba5e
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-limozeen-nots-r5.dts
@@ -0,0 +1,31 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Google Lazor Limozeen board device tree source
+ *
+ * Copyright 2021 Google LLC.
+ */
+
+/dts-v1/;
+
+#include "sc7180-trogdor.dtsi"
+#include "sc7180-trogdor-ti-sn65dsi86.dtsi"
+#include "sc7180-trogdor-lazor.dtsi"
+#include "sc7180-trogdor-lte-sku.dtsi"
+
+/ {
+	model = "Google Lazor Limozeen without Touchscreen (rev5 - rev8)";
+	/* No sku5 post-rev5 */
+	compatible = "google,lazor-rev5-sku5", "google,lazor-rev5-sku6",
+		"google,lazor-rev6-sku6", "google,lazor-rev7-sku6",
+		"google,lazor-rev8-sku6", "qcom,sc7180";
+};
+
+/delete-node/&ap_ts;
+
+&panel {
+	compatible = "innolux,n116bca-ea1", "innolux,n116bge";
+};
+
+&sdhc_2 {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-limozeen-nots-r9.dts b/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-limozeen-nots-r9.dts
new file mode 100644
index 000000000000..913b5fc3ba76
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-limozeen-nots-r9.dts
@@ -0,0 +1,28 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Google Lazor Limozeen board device tree source
+ *
+ * Copyright 2021 Google LLC.
+ */
+
+/dts-v1/;
+
+#include "sc7180-trogdor.dtsi"
+#include "sc7180-trogdor-parade-ps8640.dtsi"
+#include "sc7180-trogdor-lazor.dtsi"
+#include "sc7180-trogdor-lte-sku.dtsi"
+
+/ {
+	model = "Google Lazor Limozeen without Touchscreen (rev9+)";
+	compatible = "google,lazor-sku6", "qcom,sc7180";
+};
+
+/delete-node/&ap_ts;
+
+&panel {
+	compatible = "edp-panel";
+};
+
+&sdhc_2 {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-limozeen-nots.dts b/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-limozeen-nots.dts
deleted file mode 100644
index 0456c7e05d00..000000000000
--- a/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-limozeen-nots.dts
+++ /dev/null
@@ -1,26 +0,0 @@
-// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
-/*
- * Google Lazor Limozeen board device tree source
- *
- * Copyright 2020 Google LLC.
- */
-
-/dts-v1/;
-
-#include "sc7180-trogdor-lazor.dtsi"
-#include "sc7180-trogdor-lte-sku.dtsi"
-
-/ {
-	model = "Google Lazor Limozeen without Touchscreen";
-	compatible = "google,lazor-sku6", "google,lazor-sku5", "qcom,sc7180";
-};
-
-/delete-node/&ap_ts;
-
-&panel {
-	compatible = "innolux,n116bca-ea1", "innolux,n116bge";
-};
-
-&sdhc_2 {
-	status = "okay";
-};
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-limozeen-r4.dts b/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-limozeen-r4.dts
new file mode 100644
index 000000000000..d42dcd421146
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-limozeen-r4.dts
@@ -0,0 +1,46 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Google Lazor Limozeen board device tree source
+ *
+ * Copyright 2021 Google LLC.
+ */
+
+/dts-v1/;
+
+#include "sc7180-trogdor.dtsi"
+#include "sc7180-trogdor-ti-sn65dsi86.dtsi"
+#include "sc7180-trogdor-lazor.dtsi"
+#include "sc7180-trogdor-lte-sku.dtsi"
+
+/ {
+	model = "Google Lazor Limozeen (rev4 - rev8)";
+	compatible = "google,lazor-rev4-sku4", "google,lazor-rev5-sku4",
+		"google,lazor-rev6-sku4", "google,lazor-rev7-sku4",
+		"google,lazor-rev8-sku4", "qcom,sc7180";
+};
+
+/delete-node/&ap_ts;
+
+&ap_ts_pen_1v8 {
+	ap_ts: touchscreen@10 {
+		compatible = "elan,ekth3500";
+		reg = <0x10>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&ts_int_l>, <&ts_reset_l>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <9 IRQ_TYPE_LEVEL_LOW>;
+
+		vcc33-supply = <&pp3300_ts>;
+
+		reset-gpios = <&tlmm 8 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&panel {
+	compatible = "auo,b116xa01";
+};
+
+&sdhc_2 {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-limozeen-r9.dts b/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-limozeen-r9.dts
new file mode 100644
index 000000000000..15d77dc5f956
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-limozeen-r9.dts
@@ -0,0 +1,44 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Google Lazor Limozeen board device tree source
+ *
+ * Copyright 2021 Google LLC.
+ */
+
+/dts-v1/;
+
+#include "sc7180-trogdor.dtsi"
+#include "sc7180-trogdor-parade-ps8640.dtsi"
+#include "sc7180-trogdor-lazor.dtsi"
+#include "sc7180-trogdor-lte-sku.dtsi"
+
+/ {
+	model = "Google Lazor Limozeen (rev9+)";
+	compatible = "google,lazor-sku4", "qcom,sc7180";
+};
+
+/delete-node/&ap_ts;
+
+&ap_ts_pen_1v8 {
+	ap_ts: touchscreen@10 {
+		compatible = "elan,ekth3500";
+		reg = <0x10>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&ts_int_l>, <&ts_reset_l>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <9 IRQ_TYPE_LEVEL_LOW>;
+
+		vcc33-supply = <&pp3300_ts>;
+
+		reset-gpios = <&tlmm 8 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&panel {
+	compatible = "auo,b116xa01";
+};
+
+&sdhc_2 {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-limozeen.dts b/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-limozeen.dts
deleted file mode 100644
index e6ad6dae4e60..000000000000
--- a/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-limozeen.dts
+++ /dev/null
@@ -1,42 +0,0 @@
-// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
-/*
- * Google Lazor Limozeen board device tree source
- *
- * Copyright 2020 Google LLC.
- */
-
-/dts-v1/;
-
-#include "sc7180-trogdor-lazor.dtsi"
-#include "sc7180-trogdor-lte-sku.dtsi"
-
-/ {
-	model = "Google Lazor Limozeen";
-	compatible = "google,lazor-sku4", "qcom,sc7180";
-};
-
-/delete-node/&ap_ts;
-
-&ap_ts_pen_1v8 {
-	ap_ts: touchscreen@10 {
-		compatible = "elan,ekth3500";
-		reg = <0x10>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&ts_int_l>, <&ts_reset_l>;
-
-		interrupt-parent = <&tlmm>;
-		interrupts = <9 IRQ_TYPE_LEVEL_LOW>;
-
-		vcc33-supply = <&pp3300_ts>;
-
-		reset-gpios = <&tlmm 8 GPIO_ACTIVE_LOW>;
-	};
-};
-
-&panel {
-	compatible = "auo,b116xa01";
-};
-
-&sdhc_2 {
-	status = "okay";
-};
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-r0.dts b/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-r0.dts
index 30e3e769d2b4..d49de65aa960 100644
--- a/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-r0.dts
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-r0.dts
@@ -7,6 +7,8 @@
 
 /dts-v1/;
 
+#include "sc7180-trogdor.dtsi"
+#include "sc7180-trogdor-ti-sn65dsi86.dtsi"
 #include "sc7180-trogdor-lazor.dtsi"
 
 / {
@@ -14,17 +16,6 @@
 	compatible = "google,lazor-rev0", "qcom,sc7180";
 };
 
-&pp3300_hub {
-	/* pp3300_l7c is used to power the USB hub */
-	/delete-property/regulator-always-on;
-	/delete-property/regulator-boot-on;
-};
-
-&pp3300_l7c {
-	regulator-always-on;
-	regulator-boot-on;
-};
-
 &sn65dsi86_out {
 	/*
 	 * Lane 0 was incorrectly mapped on the cable, but we've now decided
@@ -33,3 +24,11 @@
 	 */
 	lane-polarities = <1 0>;
 };
+
+&usb_hub_2_x {
+	 vdd-supply = <&pp3300_l7c>;
+};
+
+&usb_hub_3_x {
+	 vdd-supply = <&pp3300_l7c>;
+};
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-r1-lte.dts b/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-r1-lte.dts
index e16ba7b01f25..eb20157f6af9 100644
--- a/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-r1-lte.dts
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-r1-lte.dts
@@ -13,10 +13,6 @@
 	compatible = "google,lazor-rev1-sku0", "google,lazor-rev2-sku0", "qcom,sc7180";
 };
 
-&ap_sar_sensor {
-	status = "okay";
-};
-
 &ap_sar_sensor_i2c {
 	status = "okay";
 };
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-r1.dts b/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-r1.dts
index c2ef06367baf..80c7108bc51b 100644
--- a/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-r1.dts
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-r1.dts
@@ -7,6 +7,8 @@
 
 /dts-v1/;
 
+#include "sc7180-trogdor.dtsi"
+#include "sc7180-trogdor-ti-sn65dsi86.dtsi"
 #include "sc7180-trogdor-lazor.dtsi"
 
 / {
@@ -14,13 +16,11 @@
 	compatible = "google,lazor-rev1", "google,lazor-rev2", "qcom,sc7180";
 };
 
-&pp3300_hub {
-	/* pp3300_l7c is used to power the USB hub */
-	/delete-property/regulator-always-on;
-	/delete-property/regulator-boot-on;
+
+&usb_hub_2_x {
+	 vdd-supply = <&pp3300_l7c>;
 };
 
-&pp3300_l7c {
-	regulator-always-on;
-	regulator-boot-on;
+&usb_hub_3_x {
+	 vdd-supply = <&pp3300_l7c>;
 };
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-r3-kb.dts b/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-r3-kb.dts
index dcb41afdc82a..6ff81c1f7c44 100644
--- a/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-r3-kb.dts
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-r3-kb.dts
@@ -7,12 +7,17 @@
 
 /dts-v1/;
 
+#include "sc7180-trogdor.dtsi"
+#include "sc7180-trogdor-ti-sn65dsi86.dtsi"
 #include "sc7180-trogdor-lazor.dtsi"
 #include "sc7180-lite.dtsi"
 
 / {
-	model = "Google Lazor (rev3+) with KB Backlight";
-	compatible = "google,lazor-sku2", "qcom,sc7180";
+	model = "Google Lazor (rev3 - 8) with KB Backlight";
+	compatible = "google,lazor-rev3-sku2", "google,lazor-rev4-sku2",
+		"google,lazor-rev5-sku2", "google,lazor-rev6-sku2",
+		"google,lazor-rev7-sku2", "google,lazor-rev8-sku2",
+		"qcom,sc7180";
 };
 
 &keyboard_backlight {
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-r3-lte.dts b/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-r3-lte.dts
index be44900602d7..e58e36e35950 100644
--- a/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-r3-lte.dts
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-r3-lte.dts
@@ -7,16 +7,17 @@
 
 /dts-v1/;
 
+#include "sc7180-trogdor.dtsi"
+#include "sc7180-trogdor-ti-sn65dsi86.dtsi"
 #include "sc7180-trogdor-lazor.dtsi"
 #include "sc7180-trogdor-lte-sku.dtsi"
 
 / {
-	model = "Google Lazor (rev3+) with LTE";
-	compatible = "google,lazor-sku0", "qcom,sc7180";
-};
-
-&ap_sar_sensor {
-	status = "okay";
+	model = "Google Lazor (rev3 - 8) with LTE";
+	compatible = "google,lazor-rev3-sku0", "google,lazor-rev4-sku0",
+		"google,lazor-rev5-sku0", "google,lazor-rev6-sku0",
+		"google,lazor-rev7-sku0", "google,lazor-rev8-sku0",
+		"qcom,sc7180";
 };
 
 &ap_sar_sensor_i2c {
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-r3.dts b/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-r3.dts
index b474df47cd70..76c83f88cb41 100644
--- a/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-r3.dts
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-r3.dts
@@ -7,10 +7,14 @@
 
 /dts-v1/;
 
+#include "sc7180-trogdor.dtsi"
+#include "sc7180-trogdor-ti-sn65dsi86.dtsi"
 #include "sc7180-trogdor-lazor.dtsi"
 #include "sc7180-lite.dtsi"
 
 / {
-	model = "Google Lazor (rev3+)";
-	compatible = "google,lazor", "qcom,sc7180";
+	model = "Google Lazor (rev3 - 8)";
+	compatible = "google,lazor-rev3", "google,lazor-rev4",
+		"google,lazor-rev5", "google,lazor-rev6", "google,lazor-rev7",
+		"google,lazor-rev8", "qcom,sc7180";
 };
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-r9-kb.dts b/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-r9-kb.dts
new file mode 100644
index 000000000000..960f7b7ce094
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-r9-kb.dts
@@ -0,0 +1,22 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Google Lazor board device tree source
+ *
+ * Copyright 2020 Google LLC.
+ */
+
+/dts-v1/;
+
+#include "sc7180-trogdor.dtsi"
+#include "sc7180-trogdor-parade-ps8640.dtsi"
+#include "sc7180-trogdor-lazor.dtsi"
+#include "sc7180-lite.dtsi"
+
+/ {
+	model = "Google Lazor (rev9+) with KB Backlight";
+	compatible = "google,lazor-sku2", "qcom,sc7180";
+};
+
+&keyboard_backlight {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-r9-lte.dts b/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-r9-lte.dts
new file mode 100644
index 000000000000..38027f13b9d0
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-r9-lte.dts
@@ -0,0 +1,26 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Google Lazor board device tree source
+ *
+ * Copyright 2021 Google LLC.
+ */
+
+/dts-v1/;
+
+#include "sc7180-trogdor.dtsi"
+#include "sc7180-trogdor-parade-ps8640.dtsi"
+#include "sc7180-trogdor-lazor.dtsi"
+#include "sc7180-trogdor-lte-sku.dtsi"
+
+/ {
+	model = "Google Lazor (rev9+) with LTE";
+	compatible = "google,lazor-sku0", "qcom,sc7180";
+};
+
+&ap_sar_sensor_i2c {
+	status = "okay";
+};
+
+&keyboard_backlight {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-r9.dts b/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-r9.dts
new file mode 100644
index 000000000000..56dd222650d3
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor-r9.dts
@@ -0,0 +1,18 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Google Lazor board device tree source
+ *
+ * Copyright 2021 Google LLC.
+ */
+
+/dts-v1/;
+
+#include "sc7180-trogdor.dtsi"
+#include "sc7180-trogdor-parade-ps8640.dtsi"
+#include "sc7180-trogdor-lazor.dtsi"
+#include "sc7180-lite.dtsi"
+
+/ {
+	model = "Google Lazor (rev9+)";
+	compatible = "google,lazor", "qcom,sc7180";
+};
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor.dtsi b/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor.dtsi
index 8b79fbb75756..002663d752da 100644
--- a/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor.dtsi
@@ -5,13 +5,8 @@
  * Copyright 2020 Google LLC.
  */
 
-#include "sc7180.dtsi"
-
-ap_ec_spi: &spi6 {};
-ap_h1_spi: &spi0 {};
-
-#include "sc7180-trogdor.dtsi"
-#include "sc7180-trogdor-ti-sn65dsi86.dtsi"
+/* This file must be included after sc7180-trogdor.dtsi */
+#include <arm/cros-ec-keyboard.dtsi>
 
 &ap_sar_sensor {
 	semtech,cs0-ground;
@@ -22,6 +17,10 @@ ap_h1_spi: &spi0 {};
 	semtech,avg-pos-strength = <64>;
 };
 
+&ap_tp_i2c {
+	status = "okay";
+};
+
 /*
  * Lazor is stuffed with a 47k NTC as charger thermistor which currently is
  * not supported by the PM6150 ADC driver. Disable the charger thermal zone
@@ -56,8 +55,6 @@ ap_ts_pen_1v8: &i2c4 {
 };
 
 &pm6150_adc {
-	status = "disabled";
-
 	/delete-node/ charger-thermistor@4f;
 };
 
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-mrbland-rev0-auo.dts b/arch/arm64/boot/dts/qcom/sc7180-trogdor-mrbland-rev0-auo.dts
new file mode 100644
index 000000000000..2767817fb053
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-mrbland-rev0-auo.dts
@@ -0,0 +1,22 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Google Mrbland board device tree source
+ *
+ * Copyright 2021 Google LLC.
+ *
+ * SKU: 0x0 => 0
+ *  - bits 7..4: Panel ID: 0x0 (AUO)
+ */
+
+/dts-v1/;
+
+#include "sc7180-trogdor-mrbland-rev0.dtsi"
+
+/ {
+	model = "Google Mrbland rev0 AUO panel board";
+	compatible = "google,mrbland-rev0-sku0", "qcom,sc7180";
+};
+
+&panel {
+	compatible = "auo,b101uan08.3";
+};
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-mrbland-rev0-boe.dts b/arch/arm64/boot/dts/qcom/sc7180-trogdor-mrbland-rev0-boe.dts
new file mode 100644
index 000000000000..711485574a03
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-mrbland-rev0-boe.dts
@@ -0,0 +1,22 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Google Mrbland board device tree source
+ *
+ * Copyright 2021 Google LLC.
+ *
+ * SKU: 0x10 => 16
+ *  - bits 7..4: Panel ID: 0x1 (BOE)
+ */
+
+/dts-v1/;
+
+#include "sc7180-trogdor-mrbland-rev0.dtsi"
+
+/ {
+	model = "Google Mrbland rev0 BOE panel board";
+	compatible = "google,mrbland-rev0-sku16", "qcom,sc7180";
+};
+
+&panel {
+	compatible = "boe,tv101wum-n53";
+};
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-mrbland-rev0.dtsi b/arch/arm64/boot/dts/qcom/sc7180-trogdor-mrbland-rev0.dtsi
new file mode 100644
index 000000000000..7bc8402c018e
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-mrbland-rev0.dtsi
@@ -0,0 +1,53 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Google Mrbland board device tree source
+ *
+ * Copyright 2021 Google LLC.
+ *
+ */
+
+/dts-v1/;
+
+#include "sc7180-trogdor-mrbland.dtsi"
+
+&avdd_lcd {
+	gpio = <&tlmm 80 GPIO_ACTIVE_HIGH>;
+};
+
+&panel {
+	enable-gpios = <&tlmm 76 GPIO_ACTIVE_HIGH>;
+};
+
+&v1p8_mipi {
+	gpio = <&tlmm 81 GPIO_ACTIVE_HIGH>;
+};
+
+/* PINCTRL - modifications to sc7180-trogdor-mrbland.dtsi */
+&avdd_lcd_en {
+	pinmux {
+		pins = "gpio80";
+	};
+
+	pinconf {
+		pins = "gpio80";
+	};
+};
+
+&mipi_1800_en {
+	pinmux {
+		pins = "gpio81";
+	};
+
+	pinconf {
+		pins = "gpio81";
+	};
+};
+&vdd_reset_1800 {
+	pinmux {
+		pins = "gpio76";
+	};
+
+	pinconf {
+		pins = "gpio76";
+	};
+};
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-mrbland-rev1-auo.dts b/arch/arm64/boot/dts/qcom/sc7180-trogdor-mrbland-rev1-auo.dts
new file mode 100644
index 000000000000..275313ef7554
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-mrbland-rev1-auo.dts
@@ -0,0 +1,22 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Google Mrbland board device tree source
+ *
+ * Copyright 2021 Google LLC.
+ *
+ * SKU: 0x600 => 1536
+ *  - bits 11..8: Panel ID: 0x6 (AUO)
+ */
+
+/dts-v1/;
+
+#include "sc7180-trogdor-mrbland.dtsi"
+
+/ {
+	model = "Google Mrbland rev1+ AUO panel board";
+	compatible = "google,mrbland-sku1536", "qcom,sc7180";
+};
+
+&panel {
+	compatible = "auo,b101uan08.3";
+};
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-mrbland-rev1-boe.dts b/arch/arm64/boot/dts/qcom/sc7180-trogdor-mrbland-rev1-boe.dts
new file mode 100644
index 000000000000..87c6b6c30b5e
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-mrbland-rev1-boe.dts
@@ -0,0 +1,24 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Google Mrbland board device tree source
+ *
+ * Copyright 2021 Google LLC.
+ *
+ * SKU: 0x300 => 768
+ *  - bits 11..8: Panel ID: 0x3 (BOE)
+ */
+
+/dts-v1/;
+
+#include "sc7180-trogdor-mrbland.dtsi"
+
+/ {
+	model = "Google Mrbland (rev1 - 2) BOE panel board";
+	/* Uses ID 768 on rev1 and 1024 on rev2+ */
+	compatible = "google,mrbland-sku1024", "google,mrbland-sku768",
+		"qcom,sc7180";
+};
+
+&panel {
+	compatible = "boe,tv101wum-n53";
+};
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-mrbland.dtsi b/arch/arm64/boot/dts/qcom/sc7180-trogdor-mrbland.dtsi
new file mode 100644
index 000000000000..97cba7f8064f
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-mrbland.dtsi
@@ -0,0 +1,350 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Google Mrbland board device tree source
+ *
+ * Copyright 2021 Google LLC.
+ */
+
+/dts-v1/;
+
+#include "sc7180-trogdor.dtsi"
+
+/* This board only has 1 USB Type-C port. */
+/delete-node/ &usb_c1;
+
+/ {
+	avdd_lcd: avdd-lcd {
+		compatible = "regulator-fixed";
+		regulator-name = "avdd_lcd";
+
+		gpio = <&tlmm 88 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&avdd_lcd_en>;
+
+		vin-supply = <&pp5000_a>;
+	};
+
+	avee_lcd: avee-lcd {
+		compatible = "regulator-fixed";
+		regulator-name = "avee_lcd";
+
+		gpio = <&tlmm 21 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&avee_lcd_en>;
+
+		vin-supply = <&pp5000_a>;
+	};
+
+	v1p8_mipi: v1p8-mipi {
+		compatible = "regulator-fixed";
+		regulator-name = "v1p8_mipi";
+
+		gpio = <&tlmm 86 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&mipi_1800_en>;
+
+		vin-supply = <&pp3300_a>;
+	};
+};
+
+&backlight {
+	pwms = <&cros_ec_pwm 0>;
+};
+
+&camcc {
+	status = "okay";
+};
+
+&cros_ec {
+	keyboard-controller {
+		compatible = "google,cros-ec-keyb-switches";
+	};
+};
+
+&dsi0 {
+
+	panel: panel@0 {
+		/* Compatible will be filled in per-board */
+		reg = <0>;
+		enable-gpios = <&tlmm 87 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vdd_reset_1800>;
+		avdd-supply = <&avdd_lcd>;
+		avee-supply = <&avee_lcd>;
+		pp1800-supply = <&v1p8_mipi>;
+		pp3300-supply = <&pp3300_dx_edp>;
+		backlight = <&backlight>;
+		rotation = <270>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			port@0 {
+				reg = <0>;
+				panel_in: endpoint {
+					remote-endpoint = <&dsi0_out>;
+				};
+			};
+		};
+	};
+
+	ports {
+		port@1 {
+			endpoint {
+				remote-endpoint = <&panel_in>;
+				data-lanes = <0 1 2 3>;
+			};
+		};
+	};
+};
+
+&gpio_keys {
+	status = "okay";
+};
+
+&i2c4 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	ap_ts: touchscreen@5d {
+		compatible = "goodix,gt7375p";
+		reg = <0x5d>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&ts_int_l>, <&ts_reset_l>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <9 IRQ_TYPE_LEVEL_LOW>;
+
+		reset-gpios = <&tlmm 8 GPIO_ACTIVE_LOW>;
+
+		vdd-supply = <&pp3300_ts>;
+	};
+};
+
+&pp1800_uf_cam {
+	status = "okay";
+};
+
+&pp1800_wf_cam {
+	status = "okay";
+};
+
+&pp2800_uf_cam {
+	status = "okay";
+};
+
+&pp2800_wf_cam {
+	status = "okay";
+};
+
+&wifi {
+	qcom,ath10k-calibration-variant = "GO_MRBLAND";
+};
+
+/*
+ * No eDP on this board but it's logically the same signal so just give it
+ * a new name and assign the proper GPIO.
+ */
+pp3300_disp_on: &pp3300_dx_edp {
+	gpio = <&tlmm 85 GPIO_ACTIVE_HIGH>;
+};
+
+/* PINCTRL - modifications to sc7180-trogdor.dtsi */
+
+/*
+ * No eDP on this board but it's logically the same signal so just give it
+ * a new name and assign the proper GPIO.
+ */
+
+tp_en: &en_pp3300_dx_edp {
+	pinmux {
+		pins = "gpio85";
+	};
+
+	pinconf {
+		pins = "gpio85";
+	};
+};
+
+/* PINCTRL - board-specific pinctrl */
+
+&tlmm {
+	gpio-line-names = "HUB_RST_L",
+			  "AP_RAM_ID0",
+			  "AP_SKU_ID2",
+			  "AP_RAM_ID1",
+			  "",
+			  "AP_RAM_ID2",
+			  "UF_CAM_EN",
+			  "WF_CAM_EN",
+			  "TS_RESET_L",
+			  "TS_INT_L",
+			  "",
+			  "",
+			  "AP_EDP_BKLTEN",
+			  "UF_CAM_MCLK",
+			  "WF_CAM_CLK",
+			  "",
+			  "",
+			  "UF_CAM_SDA",
+			  "UF_CAM_SCL",
+			  "WF_CAM_SDA",
+			  "WF_CAM_SCL",
+			  "AVEE_LCD_EN",
+			  "",
+			  "AMP_EN",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "HP_IRQ",
+			  "WF_CAM_RST_L",
+			  "UF_CAM_RST_L",
+			  "AP_BRD_ID2",
+			  "",
+			  "AP_BRD_ID0",
+			  "AP_H1_SPI_MISO",
+			  "AP_H1_SPI_MOSI",
+			  "AP_H1_SPI_CLK",
+			  "AP_H1_SPI_CS_L",
+			  "BT_UART_CTS",
+			  "BT_UART_RTS",
+			  "BT_UART_TXD",
+			  "BT_UART_RXD",
+			  "H1_AP_INT_ODL",
+			  "",
+			  "UART_AP_TX_DBG_RX",
+			  "UART_DBG_TX_AP_RX",
+			  "HP_I2C_SDA",
+			  "HP_I2C_SCL",
+			  "FORCED_USB_BOOT",
+			  "AMP_BCLK",
+			  "AMP_LRCLK",
+			  "AMP_DIN",
+			  "PEN_DET_ODL",
+			  "HP_BCLK",
+			  "HP_LRCLK",
+			  "HP_DOUT",
+			  "HP_DIN",
+			  "HP_MCLK",
+			  "AP_SKU_ID0",
+			  "AP_EC_SPI_MISO",
+			  "AP_EC_SPI_MOSI",
+			  "AP_EC_SPI_CLK",
+			  "AP_EC_SPI_CS_L",
+			  "AP_SPI_CLK",
+			  "AP_SPI_MOSI",
+			  "AP_SPI_MISO",
+			  /*
+			   * AP_FLASH_WP_L is crossystem ABI. Schematics
+			   * call it BIOS_FLASH_WP_L.
+			   */
+			  "AP_FLASH_WP_L",
+			  "",
+			  "AP_SPI_CS0_L",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "WLAN_SW_CTRL",
+			  "",
+			  "REPORT_E",
+			  "",
+			  "ID0",
+			  "",
+			  "ID1",
+			  "",
+			  "",
+			  "",
+			  "CODEC_PWR_EN",
+			  "HUB_EN",
+			  "TP_EN",
+			  "MIPI_1.8V_EN",
+			  "VDD_RESET_1.8V",
+			  "AVDD_LCD_EN",
+			  "",
+			  "AP_SKU_ID1",
+			  "AP_RST_REQ",
+			  "",
+			  "AP_BRD_ID1",
+			  "AP_EC_INT_L",
+			  "SDM_GRFC_3",
+			  "",
+			  "",
+			  "BOOT_CONFIG_4",
+			  "BOOT_CONFIG_2",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "BOOT_CONFIG_3",
+			  "WCI2_LTE_COEX_TXD",
+			  "WCI2_LTE_COEX_RXD",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "FORCED_USB_BOOT_POL",
+			  "AP_TS_PEN_I2C_SDA",
+			  "AP_TS_PEN_I2C_SCL",
+			  "DP_HOT_PLUG_DET",
+			  "EC_IN_RW_ODL";
+
+	avdd_lcd_en: avdd-lcd-en {
+		pinmux {
+			pins = "gpio88";
+			function = "gpio";
+		};
+
+		pinconf {
+			pins = "gpio88";
+			drive-strength = <2>;
+			bias-disable;
+		};
+	};
+
+	avee_lcd_en: avee-lcd-en {
+		pinmux {
+			pins = "gpio21";
+			function = "gpio";
+		};
+
+		pinconf {
+			pins = "gpio21";
+			drive-strength = <2>;
+			bias-disable;
+		};
+	};
+
+	mipi_1800_en: mipi-1800-en {
+		pinmux {
+			pins = "gpio86";
+			function = "gpio";
+		};
+
+		pinconf {
+			pins = "gpio86";
+			drive-strength = <2>;
+			bias-disable;
+		};
+	};
+
+	vdd_reset_1800: vdd-reset-1800 {
+		pinmux {
+			pins = "gpio87";
+			function = "gpio";
+		};
+
+		pinconf {
+			pins = "gpio87";
+			drive-strength = <2>;
+			bias-disable;
+		};
+	};
+};
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-parade-ps8640.dtsi b/arch/arm64/boot/dts/qcom/sc7180-trogdor-parade-ps8640.dtsi
index a3d69540d4e4..6a84fba178d6 100644
--- a/arch/arm64/boot/dts/qcom/sc7180-trogdor-parade-ps8640.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-parade-ps8640.dtsi
@@ -5,6 +5,8 @@
  * Copyright 2021 Google LLC.
  */
 
+#include <dt-bindings/gpio/gpio.h>
+
 / {
 	pp3300_brij_ps8640: pp3300-brij-ps8640 {
 		compatible = "regulator-fixed";
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-pazquel-lte-parade.dts b/arch/arm64/boot/dts/qcom/sc7180-trogdor-pazquel-lte-parade.dts
new file mode 100644
index 000000000000..767cb7450c0d
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-pazquel-lte-parade.dts
@@ -0,0 +1,22 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Google Pazquel board device tree source
+ *
+ * Copyright 2021 Google LLC.
+ */
+
+/dts-v1/;
+
+#include "sc7180-trogdor.dtsi"
+#include "sc7180-trogdor-parade-ps8640.dtsi"
+#include "sc7180-trogdor-pazquel.dtsi"
+#include "sc7180-trogdor-lte-sku.dtsi"
+
+/ {
+	model = "Google Pazquel (Parade,LTE)";
+	compatible = "google,pazquel-sku6", "google,pazquel-sku4", "qcom,sc7180";
+};
+
+&ap_sar_sensor_i2c {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-pazquel-lte-ti.dts b/arch/arm64/boot/dts/qcom/sc7180-trogdor-pazquel-lte-ti.dts
new file mode 100644
index 000000000000..9145b74e9009
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-pazquel-lte-ti.dts
@@ -0,0 +1,22 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Google Pazquel board device tree source
+ *
+ * Copyright 2021 Google LLC.
+ */
+
+/dts-v1/;
+
+#include "sc7180-trogdor.dtsi"
+#include "sc7180-trogdor-ti-sn65dsi86.dtsi"
+#include "sc7180-trogdor-pazquel.dtsi"
+#include "sc7180-trogdor-lte-sku.dtsi"
+
+/ {
+	model = "Google Pazquel (TI,LTE)";
+	compatible = "google,pazquel-sku0", "google,pazquel-sku2", "qcom,sc7180";
+};
+
+&ap_sar_sensor_i2c {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-pazquel-parade.dts b/arch/arm64/boot/dts/qcom/sc7180-trogdor-pazquel-parade.dts
new file mode 100644
index 000000000000..9a0e6632a786
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-pazquel-parade.dts
@@ -0,0 +1,17 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Google Pazquel board device tree source
+ *
+ * Copyright 2022 Google LLC.
+ */
+
+/dts-v1/;
+
+#include "sc7180-trogdor.dtsi"
+#include "sc7180-trogdor-parade-ps8640.dtsi"
+#include "sc7180-trogdor-pazquel.dtsi"
+
+/ {
+	model = "Google Pazquel (Parade)";
+	compatible = "google,pazquel-sku5", "qcom,sc7180";
+};
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-pazquel-ti.dts b/arch/arm64/boot/dts/qcom/sc7180-trogdor-pazquel-ti.dts
new file mode 100644
index 000000000000..47c5970d8c22
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-pazquel-ti.dts
@@ -0,0 +1,17 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Google Pazquel board device tree source
+ *
+ * Copyright 2021 Google LLC.
+ */
+
+/dts-v1/;
+
+#include "sc7180-trogdor.dtsi"
+#include "sc7180-trogdor-ti-sn65dsi86.dtsi"
+#include "sc7180-trogdor-pazquel.dtsi"
+
+/ {
+	model = "Google Pazquel (TI)";
+	compatible = "google,pazquel-sku1", "qcom,sc7180";
+};
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-pazquel.dtsi b/arch/arm64/boot/dts/qcom/sc7180-trogdor-pazquel.dtsi
new file mode 100644
index 000000000000..56d787785fd5
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-pazquel.dtsi
@@ -0,0 +1,222 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Google Pazquel board device tree source
+ *
+ * Copyright 2021 Google LLC.
+ */
+
+/* This file must be included after sc7180-trogdor.dtsi */
+#include <arm/cros-ec-keyboard.dtsi>
+
+&ap_sar_sensor {
+	compatible = "semtech,sx9324";
+	semtech,ph0-pin = <1 3 3>;
+	semtech,ph1-pin = <3 1 3>;
+	semtech,ph2-pin = <1 3 3>;
+	semtech,ph3-pin = <0 0 0>;
+	semtech,ph01-resolution = <1024>;
+	semtech,ph23-resolution = <1024>;
+	semtech,startup-sensor = <1>;
+	semtech,ph01-proxraw-strength = <3>;
+	semtech,ph23-proxraw-strength = <1>;
+	semtech,avg-pos-strength = <128>;
+	semtech,input-analog-gain = <0>;
+	semtech,cs-idle-sleep = "gnd";
+
+	/delete-property/ svdd-supply;
+	vdd-supply = <&pp1800_prox>;
+};
+
+/delete-node/&trackpad;
+&ap_tp_i2c {
+	status = "okay";
+	trackpad: trackpad@15 {
+		compatible = "hid-over-i2c";
+		reg = <0x15>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&tp_int_odl>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <0 IRQ_TYPE_EDGE_FALLING>;
+
+		vcc-supply = <&pp3300_fp_tp>;
+		post-power-on-delay-ms = <100>;
+		hid-descr-addr = <0x0001>;
+
+		wakeup-source;
+	};
+};
+
+&keyboard_controller {
+	function-row-physmap = <
+		MATRIX_KEY(0x00, 0x02, 0)	/* T1 */
+		MATRIX_KEY(0x03, 0x02, 0)	/* T2 */
+		MATRIX_KEY(0x02, 0x02, 0)	/* T3 */
+		MATRIX_KEY(0x01, 0x02, 0)	/* T4 */
+		MATRIX_KEY(0x03, 0x04, 0)	/* T5 */
+		MATRIX_KEY(0x02, 0x04, 0)	/* T6 */
+		MATRIX_KEY(0x01, 0x04, 0)	/* T7 */
+		MATRIX_KEY(0x02, 0x09, 0)	/* T8 */
+		MATRIX_KEY(0x01, 0x09, 0)	/* T9 */
+		MATRIX_KEY(0x00, 0x04, 0)	/* T10 */
+	>;
+	linux,keymap = <
+		MATRIX_KEY(0x00, 0x02, KEY_BACK)
+		MATRIX_KEY(0x03, 0x02, KEY_REFRESH)
+		MATRIX_KEY(0x02, 0x02, KEY_ZOOM)
+		MATRIX_KEY(0x01, 0x02, KEY_SCALE)
+		MATRIX_KEY(0x03, 0x04, KEY_SYSRQ)
+		MATRIX_KEY(0x02, 0x04, KEY_BRIGHTNESSDOWN)
+		MATRIX_KEY(0x01, 0x04, KEY_BRIGHTNESSUP)
+		MATRIX_KEY(0x02, 0x09, KEY_MUTE)
+		MATRIX_KEY(0x01, 0x09, KEY_VOLUMEDOWN)
+		MATRIX_KEY(0x00, 0x04, KEY_VOLUMEUP)
+		CROS_STD_MAIN_KEYMAP
+	>;
+};
+
+&panel {
+	compatible = "edp-panel";
+};
+
+&pp3300_dx_edp {
+	gpio = <&tlmm 67 GPIO_ACTIVE_HIGH>;
+};
+
+&en_pp3300_dx_edp {
+	pinmux {
+		pins = "gpio67";
+	};
+
+	pinconf {
+		pins = "gpio67";
+	};
+};
+
+/* PINCTRL - board-specific pinctrl */
+
+&tlmm {
+	gpio-line-names = "TP_INT_ODL",
+			  "AP_RAM_ID0",
+			  "AP_SKU_ID2",
+			  "AP_RAM_ID1",
+			  "",
+			  "AP_RAM_ID2",
+			  "AP_TP_I2C_SDA",
+			  "AP_TP_I2C_SCL",
+			  "TS_RESET_L",
+			  "TS_INT_L",
+			  "",
+			  "EDP_BRIJ_IRQ",
+			  "AP_EDP_BKLTEN",
+			  "",
+			  "",
+			  "EDP_BRIJ_I2C_SDA",
+			  "EDP_BRIJ_I2C_SCL",
+			  "HUB_RST_L",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "AMP_EN",
+			  "P_SENSOR_INT_L",
+			  "AP_SAR_SENSOR_SDA",
+			  "AP_SAR_SENSOR_SCL",
+			  "",
+			  "HP_IRQ",
+			  "",
+			  "",
+			  "AP_BRD_ID2",
+			  "BRIJ_SUSPEND",
+			  "AP_BRD_ID0",
+			  "AP_H1_SPI_MISO",
+			  "AP_H1_SPI_MOSI",
+			  "AP_H1_SPI_CLK",
+			  "AP_H1_SPI_CS_L",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "H1_AP_INT_ODL",
+			  "",
+			  "UART_AP_TX_DBG_RX",
+			  "UART_DBG_TX_AP_RX",
+			  "HP_I2C_SDA",
+			  "HP_I2C_SCL",
+			  "FORCED_USB_BOOT",
+			  "AMP_BCLK",
+			  "AMP_LRCLK",
+			  "AMP_DIN",
+			  "",
+			  "HP_BCLK",
+			  "HP_LRCLK",
+			  "HP_DOUT",
+			  "HP_DIN",
+			  "HP_MCLK",
+			  "AP_SKU_ID0",
+			  "AP_EC_SPI_MISO",
+			  "AP_EC_SPI_MOSI",
+			  "AP_EC_SPI_CLK",
+			  "AP_EC_SPI_CS_L",
+			  "AP_SPI_CLK",
+			  "AP_SPI_MOSI",
+			  "AP_SPI_MISO",
+			  /*
+			   * AP_FLASH_WP_L is crossystem ABI. Schematics
+			   * call it BIOS_FLASH_WP_L.
+			   */
+			  "AP_FLASH_WP_L",
+			  "EN_PP3300_DX_EDP",
+			  "AP_SPI_CS0_L",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "UIM2_DATA",
+			  "UIM2_CLK",
+			  "UIM2_RST",
+			  "UIM2_PRESENT",
+			  "UIM1_DATA",
+			  "UIM1_CLK",
+			  "UIM1_RST",
+			  "",
+			  "CODEC_PWR_EN",
+			  "HUB_EN",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "AP_SKU_ID1",
+			  "AP_RST_REQ",
+			  "",
+			  "AP_BRD_ID1",
+			  "AP_EC_INT_L",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "EDP_BRIJ_EN",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "AP_TS_PEN_I2C_SDA",
+			  "AP_TS_PEN_I2C_SCL",
+			  "DP_HOT_PLUG_DET",
+			  "EC_IN_RW_ODL";
+};
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-pompom-r1.dts b/arch/arm64/boot/dts/qcom/sc7180-trogdor-pompom-r1.dts
index 76a130bad60a..8467ff41e6d5 100644
--- a/arch/arm64/boot/dts/qcom/sc7180-trogdor-pompom-r1.dts
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-pompom-r1.dts
@@ -34,13 +34,10 @@
 	/delete-node/ charger-thermistor@0;
 };
 
-&pp3300_hub {
-	/* pp3300_l7c is used to power the USB hub */
-	/delete-property/regulator-always-on;
-	/delete-property/regulator-boot-on;
+&usb_hub_2_x {
+	 vdd-supply = <&pp3300_l7c>;
 };
 
-&pp3300_l7c {
-	regulator-always-on;
-	regulator-boot-on;
+&usb_hub_3_x {
+	 vdd-supply = <&pp3300_l7c>;
 };
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-pompom.dtsi b/arch/arm64/boot/dts/qcom/sc7180-trogdor-pompom.dtsi
index e90f99ef5323..a7582fb547ee 100644
--- a/arch/arm64/boot/dts/qcom/sc7180-trogdor-pompom.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-pompom.dtsi
@@ -5,12 +5,9 @@
  * Copyright 2020 Google LLC.
  */
 
-#include "sc7180.dtsi"
-
-ap_ec_spi: &spi6 {};
-ap_h1_spi: &spi0 {};
-
 #include "sc7180-trogdor.dtsi"
+/* Must come after sc7180-trogdor.dtsi to modify cros_ec */
+#include <arm/cros-ec-keyboard.dtsi>
 #include "sc7180-trogdor-ti-sn65dsi86.dtsi"
 
 / {
@@ -33,7 +30,11 @@ ap_h1_spi: &spi0 {};
 };
 
 &alc5682 {
-	realtek,dmic-clk-driving-high = "true";
+	realtek,dmic-clk-driving-high;
+};
+
+&ap_tp_i2c {
+	status = "okay";
 };
 
 &cpu6_alert0 {
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-quackingstick-r0-lte.dts b/arch/arm64/boot/dts/qcom/sc7180-trogdor-quackingstick-r0-lte.dts
new file mode 100644
index 000000000000..35e8945fc56d
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-quackingstick-r0-lte.dts
@@ -0,0 +1,38 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Google Quackingstick board device tree source
+ *
+ * Copyright 2021 Google LLC.
+ *
+ * SKU: 0x600 => 1536
+ *  - bits 11..8: Panel ID: 0x6 (AUO)
+ */
+
+#include "sc7180-trogdor-quackingstick-r0.dts"
+#include "sc7180-trogdor-lte-sku.dtsi"
+
+/ {
+	model = "Google Quackingstick (rev0+) with LTE";
+	compatible = "google,quackingstick-sku1536", "qcom,sc7180";
+};
+
+&ap_sar_sensor {
+	compatible = "semtech,sx9324";
+	semtech,ph0-pin = <3 1 3>;
+	semtech,ph1-pin = <2 1 2>;
+	semtech,ph2-pin = <3 3 1>;
+	semtech,ph3-pin = <1 3 3>;
+	semtech,ph01-resolution = <1024>;
+	semtech,ph23-resolution = <1024>;
+	semtech,startup-sensor = <1>;
+	semtech,ph01-proxraw-strength = <3>;
+	semtech,ph23-proxraw-strength = <3>;
+	semtech,avg-pos-strength = <256>;
+
+	/delete-property/ svdd-supply;
+	vdd-supply = <&pp1800_prox>;
+};
+
+&ap_sar_sensor_i2c {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-quackingstick-r0.dts b/arch/arm64/boot/dts/qcom/sc7180-trogdor-quackingstick-r0.dts
new file mode 100644
index 000000000000..5c81e44ed4a5
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-quackingstick-r0.dts
@@ -0,0 +1,26 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Google Quackingstick board device tree source
+ *
+ * Copyright 2021 Google LLC.
+ *
+ * SKU: 0x601 => 1537
+ *  - bits 11..8: Panel ID: 0x6 (AUO)
+ */
+
+#include "sc7180-trogdor-quackingstick.dtsi"
+
+/ {
+	model = "Google Quackingstick (rev0+)";
+	compatible = "google,quackingstick-sku1537", "qcom,sc7180";
+};
+
+&dsi_phy {
+	qcom,phy-rescode-offset-top = /bits/ 8 <(-13) (-13) (-13) (-13) (-13)>;
+	qcom,phy-rescode-offset-bot = /bits/ 8 <(-13) (-13) (-13) (-13) (-13)>;
+	qcom,phy-drive-ldo-level = <375>;
+};
+
+&panel {
+	compatible = "auo,b101uan08.3";
+};
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-quackingstick.dtsi b/arch/arm64/boot/dts/qcom/sc7180-trogdor-quackingstick.dtsi
new file mode 100644
index 000000000000..695b04fe7221
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-quackingstick.dtsi
@@ -0,0 +1,324 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Google Quackingstick board device tree source
+ *
+ * Copyright 2021 Google LLC.
+ */
+
+/dts-v1/;
+
+#include "sc7180-trogdor.dtsi"
+
+/* This board only has 1 USB Type-C port. */
+/delete-node/ &usb_c1;
+
+/ {
+	ppvar_lcd: ppvar-lcd {
+		compatible = "regulator-fixed";
+		regulator-name = "ppvar_lcd";
+
+		gpio = <&tlmm 88 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&ppvar_lcd_en>;
+
+		vin-supply = <&pp5000_a>;
+	};
+
+	v1p8_disp: v1p8-disp {
+		compatible = "regulator-fixed";
+		regulator-name = "v1p8_disp";
+
+		gpio = <&tlmm 86 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pp1800_disp_on>;
+
+		vin-supply = <&pp3300_a>;
+	};
+};
+
+&backlight {
+	pwms = <&cros_ec_pwm 0>;
+};
+
+&camcc {
+	status = "okay";
+};
+
+&cros_ec {
+	keyboard-controller {
+		compatible = "google,cros-ec-keyb-switches";
+	};
+};
+
+&dsi0 {
+	panel: panel@0 {
+		/* Compatible will be filled in per-board */
+		reg = <0>;
+		enable-gpios = <&tlmm 87 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&lcd_rst>;
+		avdd-supply = <&ppvar_lcd>;
+		pp1800-supply = <&v1p8_disp>;
+		pp3300-supply = <&pp3300_dx_edp>;
+		backlight = <&backlight>;
+		rotation = <270>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			port@0 {
+				reg = <0>;
+				panel_in: endpoint {
+					remote-endpoint = <&dsi0_out>;
+				};
+			};
+		};
+	};
+
+	ports {
+		port@1 {
+			endpoint {
+				remote-endpoint = <&panel_in>;
+				data-lanes = <0 1 2 3>;
+			};
+		};
+	};
+};
+
+&gpio_keys {
+	status = "okay";
+};
+
+&i2c4 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	ap_ts: touchscreen@10 {
+		compatible = "hid-over-i2c";
+		reg = <0x10>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&ts_int_l>, <&ts_reset_l>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <9 IRQ_TYPE_LEVEL_LOW>;
+
+		post-power-on-delay-ms = <20>;
+		hid-descr-addr = <0x0001>;
+
+		vdd-supply = <&pp3300_ts>;
+	};
+};
+
+&sdhc_2 {
+	status = "okay";
+};
+
+&pp1800_uf_cam {
+	status = "okay";
+};
+
+&pp1800_wf_cam {
+	status = "okay";
+};
+
+&pp2800_uf_cam {
+	status = "okay";
+};
+
+&pp2800_wf_cam {
+	status = "okay";
+};
+
+/*
+ * No eDP on this board but it's logically the same signal so just give it
+ * a new name and assign the proper GPIO.
+ */
+pp3300_disp_on: &pp3300_dx_edp {
+	gpio = <&tlmm 67 GPIO_ACTIVE_HIGH>;
+};
+
+/* PINCTRL - modifications to sc7180-trogdor.dtsi */
+
+/*
+ * No eDP on this board but it's logically the same signal so just give it
+ * a new name and assign the proper GPIO.
+ */
+
+tp_en: &en_pp3300_dx_edp {
+	pinmux {
+		pins = "gpio67";
+	};
+
+	pinconf {
+		pins = "gpio67";
+	};
+};
+
+/* PINCTRL - board-specific pinctrl */
+
+&tlmm {
+	gpio-line-names = "HUB_RST_L",
+			  "AP_RAM_ID0",
+			  "AP_SKU_ID2",
+			  "AP_RAM_ID1",
+			  "",
+			  "AP_RAM_ID2",
+			  "UF_CAM_EN",
+			  "WF_CAM_EN",
+			  "TS_RESET_L",
+			  "TS_INT_L",
+			  "",
+			  "",
+			  "AP_EDP_BKLTEN",
+			  "UF_CAM_MCLK",
+			  "WF_CAM_CLK",
+			  "EDP_BRIJ_I2C_SDA",
+			  "EDP_BRIJ_I2C_SCL",
+			  "UF_CAM_SDA",
+			  "UF_CAM_SCL",
+			  "WF_CAM_SDA",
+			  "WF_CAM_SCL",
+			  "",
+			  "",
+			  "AMP_EN",
+			  "P_SENSOR_INT_L",
+			  "AP_SAR_SENSOR_SDA",
+			  "AP_SAR_SENSOR_SCL",
+			  "",
+			  "HP_IRQ",
+			  "WF_CAM_RST_L",
+			  "UF_CAM_RST_L",
+			  "AP_BRD_ID2",
+			  "",
+			  "AP_BRD_ID0",
+			  "AP_H1_SPI_MISO",
+			  "AP_H1_SPI_MOSI",
+			  "AP_H1_SPI_CLK",
+			  "AP_H1_SPI_CS_L",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "H1_AP_INT_ODL",
+			  "",
+			  "UART_AP_TX_DBG_RX",
+			  "UART_DBG_TX_AP_RX",
+			  "HP_I2C_SDA",
+			  "HP_I2C_SCL",
+			  "FORCED_USB_BOOT",
+			  "",
+			  "",
+			  "AMP_DIN",
+			  "PEN_DET_ODL",
+			  "HP_BCLK",
+			  "HP_LRCLK",
+			  "HP_DOUT",
+			  "HP_DIN",
+			  "HP_MCLK",
+			  "AP_SKU_ID0",
+			  "AP_EC_SPI_MISO",
+			  "AP_EC_SPI_MOSI",
+			  "AP_EC_SPI_CLK",
+			  "AP_EC_SPI_CS_L",
+			  "AP_SPI_CLK",
+			  "AP_SPI_MOSI",
+			  "AP_SPI_MISO",
+			  /*
+			   * AP_FLASH_WP_L is crossystem ABI. Schematics
+			   * call it BIOS_FLASH_WP_L.
+			   */
+			  "AP_FLASH_WP_L",
+			  "EN_PP3300_DX_EDP",
+			  "AP_SPI_CS0_L",
+			  "SD_CD_ODL",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "UIM2_DATA",
+			  "UIM2_CLK",
+			  "UIM2_RST",
+			  "UIM2_PRESENT_L",
+			  "UIM1_DATA",
+			  "UIM1_CLK",
+			  "UIM1_RST",
+			  "",
+			  "CODEC_PWR_EN",
+			  "HUB_EN",
+			  "",
+			  "PP1800_DISP_ON",
+			  "LCD_RST",
+			  "PPVAR_LCD_EN",
+			  "",
+			  "AP_SKU_ID1",
+			  "AP_RST_REQ",
+			  "",
+			  "AP_BRD_ID1",
+			  "AP_EC_INT_L",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "AP_TS_I2C_SDA",
+			  "AP_TS_I2C_SCL",
+			  "DP_HOT_PLUG_DET",
+			  "EC_IN_RW_ODL";
+
+	lcd_rst: lcd-rst {
+		pinmux {
+			pins = "gpio87";
+			function = "gpio";
+		};
+
+		pinconf {
+			pins = "gpio87";
+			drive-strength = <2>;
+			bias-disable;
+		};
+	};
+
+	ppvar_lcd_en: ppvar-lcd-en {
+		pinmux {
+			pins = "gpio88";
+			function = "gpio";
+		};
+
+		pinconf {
+			pins = "gpio88";
+			drive-strength = <2>;
+			bias-disable;
+		};
+	};
+
+	pp1800_disp_on: pp1800-disp-on {
+		pinmux {
+			pins = "gpio86";
+			function = "gpio";
+		};
+
+		pinconf {
+			pins = "gpio86";
+			drive-strength = <2>;
+			bias-disable;
+		};
+	};
+};
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-r1.dts b/arch/arm64/boot/dts/qcom/sc7180-trogdor-r1.dts
index 457c25499863..bc097d1b1b23 100644
--- a/arch/arm64/boot/dts/qcom/sc7180-trogdor-r1.dts
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-r1.dts
@@ -7,12 +7,9 @@
 
 /dts-v1/;
 
-#include "sc7180.dtsi"
-
-ap_ec_spi: &spi6 {};
-ap_h1_spi: &spi0 {};
-
 #include "sc7180-trogdor.dtsi"
+/* Must come after sc7180-trogdor.dtsi to modify cros_ec */
+#include <arm/cros-ec-keyboard.dtsi>
 #include "sc7180-trogdor-ti-sn65dsi86.dtsi"
 
 / {
@@ -20,6 +17,10 @@ ap_h1_spi: &spi0 {};
 	compatible = "google,trogdor", "qcom,sc7180";
 };
 
+&ap_tp_i2c {
+	status = "okay";
+};
+
 ap_ts_pen_1v8: &i2c4 {
 	status = "okay";
 	clock-frequency = <400000>;
@@ -43,17 +44,6 @@ ap_ts_pen_1v8: &i2c4 {
 	compatible = "auo,b116xa01";
 };
 
-&pp3300_hub {
-	/* pp3300_l7c is used to power the USB hub */
-	/delete-property/regulator-always-on;
-	/delete-property/regulator-boot-on;
-};
-
-&pp3300_l7c {
-	regulator-always-on;
-	regulator-boot-on;
-};
-
 &sdhc_2 {
 	status = "okay";
 };
@@ -62,6 +52,14 @@ ap_ts_pen_1v8: &i2c4 {
 	interrupts = <58 IRQ_TYPE_EDGE_FALLING>;
 };
 
+&usb_hub_2_x {
+	 vdd-supply = <&pp3300_l7c>;
+};
+
+&usb_hub_3_x {
+	 vdd-supply = <&pp3300_l7c>;
+};
+
 /* PINCTRL - modifications to sc7180-trogdor.dtsi */
 
 &trackpad_int_1v8_odl {
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-ti-sn65dsi86.dtsi b/arch/arm64/boot/dts/qcom/sc7180-trogdor-ti-sn65dsi86.dtsi
index 97d5e45abd1d..f869e6a343c1 100644
--- a/arch/arm64/boot/dts/qcom/sc7180-trogdor-ti-sn65dsi86.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-ti-sn65dsi86.dtsi
@@ -5,9 +5,10 @@
  * Copyright 2021 Google LLC.
  */
 
+#include <dt-bindings/gpio/gpio.h>
+
 &dsi0_out {
 	remote-endpoint = <&sn65dsi86_in>;
-	data-lanes = <0 1 2 3>;
 };
 
 edp_brij_i2c: &i2c2 {
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-wormdingler-rev0-boe.dts b/arch/arm64/boot/dts/qcom/sc7180-trogdor-wormdingler-rev0-boe.dts
new file mode 100644
index 000000000000..d6ed7d0afe4a
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-wormdingler-rev0-boe.dts
@@ -0,0 +1,22 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Google Wormdingler board device tree source
+ *
+ * Copyright 2021 Google LLC.
+ *
+ * SKU: 0x10 => 16
+ *  - bits 7..4: Panel ID: 0x1 (BOE)
+ */
+
+/dts-v1/;
+
+#include "sc7180-trogdor-wormdingler-rev0.dtsi"
+
+/ {
+	model = "Google Wormdingler rev0 BOE panel board";
+	compatible = "google,wormdingler-rev0-sku16", "qcom,sc7180";
+};
+
+&panel {
+	compatible = "boe,tv110c9m-ll3";
+};
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-wormdingler-rev0-inx.dts b/arch/arm64/boot/dts/qcom/sc7180-trogdor-wormdingler-rev0-inx.dts
new file mode 100644
index 000000000000..c03525ea64ca
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-wormdingler-rev0-inx.dts
@@ -0,0 +1,22 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Google Wormdingler board device tree source
+ *
+ * Copyright 2021 Google LLC.
+ *
+ * SKU: 0x0 => 0
+ *  - bits 7..4: Panel ID: 0x0 (INX)
+ */
+
+/dts-v1/;
+
+#include "sc7180-trogdor-wormdingler-rev0.dtsi"
+
+/ {
+	model = "Google Wormdingler rev0 INX panel board";
+	compatible = "google,wormdingler-rev0-sku0", "qcom,sc7180";
+};
+
+&panel {
+	compatible = "innolux,hj110iz-01a";
+};
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-wormdingler-rev0.dtsi b/arch/arm64/boot/dts/qcom/sc7180-trogdor-wormdingler-rev0.dtsi
new file mode 100644
index 000000000000..db29e0cba29d
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-wormdingler-rev0.dtsi
@@ -0,0 +1,53 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Google Wormdingler board device tree source
+ *
+ * Copyright 2021 Google LLC.
+ *
+ */
+
+/dts-v1/;
+
+#include "sc7180-trogdor-wormdingler.dtsi"
+
+&avdd_lcd {
+	gpio = <&tlmm 80 GPIO_ACTIVE_HIGH>;
+};
+
+&panel {
+	enable-gpios = <&tlmm 76 GPIO_ACTIVE_HIGH>;
+};
+
+&v1p8_mipi {
+	gpio = <&tlmm 81 GPIO_ACTIVE_HIGH>;
+};
+
+/* PINCTRL - modifications to sc7180-trogdor-wormdingler.dtsi */
+&avdd_lcd_en {
+	pinmux {
+		pins = "gpio80";
+	};
+
+	pinconf {
+		pins = "gpio80";
+	};
+};
+
+&mipi_1800_en {
+	pinmux {
+		pins = "gpio81";
+	};
+
+	pinconf {
+		pins = "gpio81";
+	};
+};
+&vdd_reset_1800 {
+	pinmux {
+		pins = "gpio76";
+	};
+
+	pinconf {
+		pins = "gpio76";
+	};
+};
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-wormdingler-rev1-boe-rt5682s.dts b/arch/arm64/boot/dts/qcom/sc7180-trogdor-wormdingler-rev1-boe-rt5682s.dts
new file mode 100644
index 000000000000..aa605885c371
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-wormdingler-rev1-boe-rt5682s.dts
@@ -0,0 +1,29 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Google Wormdingler board device tree source
+ *
+ * Copyright 2021 Google LLC.
+ *
+ * SKU: 0x401 => 1025
+ *  - bits 11..8: Panel ID: 0x4 (BOE)
+ */
+
+/dts-v1/;
+
+#include "sc7180-trogdor-wormdingler-rev1-boe.dts"
+
+/ {
+	model = "Google Wormdingler rev1+ (BOE, rt5682s)";
+	compatible = "google,wormdingler-sku1025", "qcom,sc7180";
+};
+
+&alc5682 {
+	compatible = "realtek,rt5682s";
+	realtek,dmic1-clk-pin = <2>;
+	realtek,dmic-clk-rate-hz = <2048000>;
+};
+
+&sound {
+	compatible = "google,sc7180-trogdor";
+	model = "sc7180-rt5682s-max98357a-1mic";
+};
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-wormdingler-rev1-boe.dts b/arch/arm64/boot/dts/qcom/sc7180-trogdor-wormdingler-rev1-boe.dts
new file mode 100644
index 000000000000..c5b0658bd632
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-wormdingler-rev1-boe.dts
@@ -0,0 +1,28 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Google Wormdingler board device tree source
+ *
+ * Copyright 2021 Google LLC.
+ *
+ * SKU: 0x400 => 1024
+ *  - bits 11..8: Panel ID: 0x4 (BOE)
+ */
+
+/dts-v1/;
+
+#include "sc7180-trogdor-wormdingler.dtsi"
+
+/ {
+	model = "Google Wormdingler rev1+ BOE panel board";
+	compatible = "google,wormdingler-sku1024", "qcom,sc7180";
+};
+
+&dsi_phy {
+	qcom,phy-rescode-offset-top = /bits/ 8 <31 31 31 31 (-32)>;
+	qcom,phy-rescode-offset-bot = /bits/ 8 <31 31 31 31 (-32)>;
+	qcom,phy-drive-ldo-level = <450>;
+};
+
+&panel {
+	compatible = "boe,tv110c9m-ll3";
+};
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-wormdingler-rev1-inx-rt5682s.dts b/arch/arm64/boot/dts/qcom/sc7180-trogdor-wormdingler-rev1-inx-rt5682s.dts
new file mode 100644
index 000000000000..7116c44c8d85
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-wormdingler-rev1-inx-rt5682s.dts
@@ -0,0 +1,29 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Google Wormdingler board device tree source
+ *
+ * Copyright 2021 Google LLC.
+ *
+ * SKU: 0x0001 => 1
+ *  - bits 11..8: Panel ID: 0x0 (INX)
+ */
+
+/dts-v1/;
+
+#include "sc7180-trogdor-wormdingler-rev1-inx.dts"
+
+/ {
+	model = "Google Wormdingler rev1+ (INX, rt5682s)";
+	compatible = "google,wormdingler-sku1", "qcom,sc7180";
+};
+
+&alc5682 {
+	compatible = "realtek,rt5682s";
+	realtek,dmic1-clk-pin = <2>;
+	realtek,dmic-clk-rate-hz = <2048000>;
+};
+
+&sound {
+	compatible = "google,sc7180-trogdor";
+	model = "sc7180-rt5682s-max98357a-1mic";
+};
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-wormdingler-rev1-inx.dts b/arch/arm64/boot/dts/qcom/sc7180-trogdor-wormdingler-rev1-inx.dts
new file mode 100644
index 000000000000..dd34a2297ea0
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-wormdingler-rev1-inx.dts
@@ -0,0 +1,22 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Google Wormdingler board device tree source
+ *
+ * Copyright 2021 Google LLC.
+ *
+ * SKU: 0x0000 => 0
+ *  - bits 11..8: Panel ID: 0x0 (INX)
+ */
+
+/dts-v1/;
+
+#include "sc7180-trogdor-wormdingler.dtsi"
+
+/ {
+	model = "Google Wormdingler rev1+ INX panel board";
+	compatible = "google,wormdingler-sku0", "qcom,sc7180";
+};
+
+&panel {
+	compatible = "innolux,hj110iz-01a";
+};
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-wormdingler.dtsi b/arch/arm64/boot/dts/qcom/sc7180-trogdor-wormdingler.dtsi
new file mode 100644
index 000000000000..6312108e8b3e
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-wormdingler.dtsi
@@ -0,0 +1,412 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Google Wormdingler board device tree source
+ *
+ * Copyright 2021 Google LLC.
+ */
+
+/dts-v1/;
+
+#include "sc7180-trogdor.dtsi"
+
+/ {
+	avdd_lcd: avdd-lcd {
+		compatible = "regulator-fixed";
+		regulator-name = "avdd_lcd";
+
+		gpio = <&tlmm 88 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&avdd_lcd_en>;
+
+		vin-supply = <&pp5000_a>;
+	};
+
+	avee_lcd: avee-lcd {
+		compatible = "regulator-fixed";
+		regulator-name = "avee_lcd";
+
+		gpio = <&tlmm 21 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&avee_lcd_en>;
+
+		vin-supply = <&pp5000_a>;
+	};
+
+	pp1800_ts:
+	v1p8_mipi: v1p8-mipi {
+		compatible = "regulator-fixed";
+		regulator-name = "v1p8_mipi";
+
+		gpio = <&tlmm 86 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&mipi_1800_en>;
+
+		vin-supply = <&pp3300_a>;
+	};
+
+	thermal-zones {
+		skin_temp_thermal: skin-temp-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <0>;
+
+			thermal-sensors = <&pm6150_adc_tm 1>;
+			sustainable-power = <574>;
+
+			trips {
+				skin_temp_alert0: trip-point0 {
+					temperature = <58000>;
+					hysteresis = <1000>;
+					type = "passive";
+				};
+
+				skin_temp_alert1: trip-point1 {
+					temperature = <62500>;
+					hysteresis = <1000>;
+					type = "passive";
+				};
+
+				skin-temp-crit {
+					temperature = <68000>;
+					hysteresis = <1000>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				map0 {
+					trip = <&skin_temp_alert0>;
+					cooling-device = <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+
+				map1 {
+					trip = <&skin_temp_alert1>;
+					cooling-device = <&CPU6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&CPU7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+	};
+};
+
+&backlight {
+	pwms = <&cros_ec_pwm 0>;
+};
+
+&camcc {
+	status = "okay";
+};
+
+&cros_ec {
+	base_detection: cbas {
+		compatible = "google,cros-cbas";
+	};
+
+	keyboard-controller {
+		compatible = "google,cros-ec-keyb-switches";
+	};
+};
+
+&dsi0 {
+
+	panel: panel@0 {
+		reg = <0>;
+		enable-gpios = <&tlmm 87 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vdd_reset_1800>;
+		avdd-supply = <&avdd_lcd>;
+		avee-supply = <&avee_lcd>;
+		pp1800-supply = <&v1p8_mipi>;
+		pp3300-supply = <&pp3300_dx_edp>;
+		backlight = <&backlight>;
+		rotation = <270>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			port@0 {
+				reg = <0>;
+				panel_in: endpoint {
+					remote-endpoint = <&dsi0_out>;
+				};
+			};
+		};
+	};
+
+	ports {
+		port@1 {
+			endpoint {
+				remote-endpoint = <&panel_in>;
+				data-lanes = <0 1 2 3>;
+			};
+		};
+	};
+};
+
+&i2c4 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	ap_ts: touchscreen@1 {
+		compatible = "hid-over-i2c";
+		reg = <0x01>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&ts_int_l>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <9 IRQ_TYPE_EDGE_FALLING>;
+
+		post-power-on-delay-ms = <70>;
+		hid-descr-addr = <0x0001>;
+
+		vdd-supply = <&pp3300_ts>;
+		vddl-supply = <&pp1800_ts>;
+	};
+};
+
+&pm6150_adc {
+	skin-temp-thermistor@4d {
+		reg = <ADC5_AMUX_THM1_100K_PU>;
+		qcom,ratiometric;
+		qcom,hw-settle-time = <200>;
+	};
+};
+
+&pm6150_adc_tm {
+	status = "okay";
+
+	skin-temp-thermistor@1 {
+		reg = <1>;
+		io-channels = <&pm6150_adc ADC5_AMUX_THM1_100K_PU>;
+		qcom,ratiometric;
+		qcom,hw-settle-time-us = <200>;
+	};
+};
+
+&pp1800_uf_cam {
+	status = "okay";
+};
+
+&pp1800_wf_cam {
+	status = "okay";
+};
+
+&pp2800_uf_cam {
+	status = "okay";
+};
+
+&pp2800_wf_cam {
+	status = "okay";
+};
+
+&wifi {
+	qcom,ath10k-calibration-variant = "GO_WORMDINGLER";
+};
+
+/*
+ * No eDP on this board but it's logically the same signal so just give it
+ * a new name and assign the proper GPIO.
+ */
+pp3300_disp_on: &pp3300_dx_edp {
+	gpio = <&tlmm 85 GPIO_ACTIVE_HIGH>;
+};
+
+/* PINCTRL - modifications to sc7180-trogdor.dtsi */
+
+/*
+ * No eDP on this board but it's logically the same signal so just give it
+ * a new name and assign the proper GPIO.
+ */
+
+tp_en: &en_pp3300_dx_edp {
+	pinmux {
+		pins = "gpio85";
+	};
+
+	pinconf {
+		pins = "gpio85";
+	};
+};
+
+/* PINCTRL - board-specific pinctrl */
+
+&tlmm {
+	gpio-line-names = "HUB_RST_L",
+			  "AP_RAM_ID0",
+			  "AP_SKU_ID2",
+			  "AP_RAM_ID1",
+			  "",
+			  "AP_RAM_ID2",
+			  "UF_CAM_EN",
+			  "WF_CAM_EN",
+			  "TS_RESET_L",
+			  "TS_INT_L",
+			  "",
+			  "",
+			  "AP_EDP_BKLTEN",
+			  "UF_CAM_MCLK",
+			  "WF_CAM_CLK",
+			  "",
+			  "",
+			  "UF_CAM_SDA",
+			  "UF_CAM_SCL",
+			  "WF_CAM_SDA",
+			  "WF_CAM_SCL",
+			  "AVEE_LCD_EN",
+			  "",
+			  "AMP_EN",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "HP_IRQ",
+			  "WF_CAM_RST_L",
+			  "UF_CAM_RST_L",
+			  "AP_BRD_ID2",
+			  "",
+			  "AP_BRD_ID0",
+			  "AP_H1_SPI_MISO",
+			  "AP_H1_SPI_MOSI",
+			  "AP_H1_SPI_CLK",
+			  "AP_H1_SPI_CS_L",
+			  "BT_UART_CTS",
+			  "BT_UART_RTS",
+			  "BT_UART_TXD",
+			  "BT_UART_RXD",
+			  "H1_AP_INT_ODL",
+			  "",
+			  "UART_AP_TX_DBG_RX",
+			  "UART_DBG_TX_AP_RX",
+			  "HP_I2C_SDA",
+			  "HP_I2C_SCL",
+			  "FORCED_USB_BOOT",
+			  "AMP_BCLK",
+			  "AMP_LRCLK",
+			  "AMP_DIN",
+			  "",
+			  "HP_BCLK",
+			  "HP_LRCLK",
+			  "HP_DOUT",
+			  "HP_DIN",
+			  "HP_MCLK",
+			  "AP_SKU_ID0",
+			  "AP_EC_SPI_MISO",
+			  "AP_EC_SPI_MOSI",
+			  "AP_EC_SPI_CLK",
+			  "AP_EC_SPI_CS_L",
+			  "AP_SPI_CLK",
+			  "AP_SPI_MOSI",
+			  "AP_SPI_MISO",
+			  /*
+			   * AP_FLASH_WP_L is crossystem ABI. Schematics
+			   * call it BIOS_FLASH_WP_L.
+			   */
+			  "AP_FLASH_WP_L",
+			  "",
+			  "AP_SPI_CS0_L",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "WLAN_SW_CTRL",
+			  "",
+			  "REPORT_E",
+			  "",
+			  "ID0",
+			  "",
+			  "ID1",
+			  "",
+			  "",
+			  "",
+			  "CODEC_PWR_EN",
+			  "HUB_EN",
+			  "TP_EN",
+			  "MIPI_1.8V_EN",
+			  "VDD_RESET_1.8V",
+			  "AVDD_LCD_EN",
+			  "",
+			  "AP_SKU_ID1",
+			  "AP_RST_REQ",
+			  "",
+			  "AP_BRD_ID1",
+			  "AP_EC_INT_L",
+			  "SDM_GRFC_3",
+			  "",
+			  "",
+			  "BOOT_CONFIG_4",
+			  "BOOT_CONFIG_2",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "BOOT_CONFIG_3",
+			  "WCI2_LTE_COEX_TXD",
+			  "WCI2_LTE_COEX_RXD",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "FORCED_USB_BOOT_POL",
+			  "AP_TS_PEN_I2C_SDA",
+			  "AP_TS_PEN_I2C_SCL",
+			  "DP_HOT_PLUG_DET",
+			  "EC_IN_RW_ODL";
+
+	avdd_lcd_en: avdd-lcd-en {
+		pinmux {
+			pins = "gpio88";
+			function = "gpio";
+		};
+
+		pinconf {
+			pins = "gpio88";
+			drive-strength = <2>;
+			bias-disable;
+		};
+	};
+
+	avee_lcd_en: avee-lcd-en {
+		pinmux {
+			pins = "gpio21";
+			function = "gpio";
+		};
+
+		pinconf {
+			pins = "gpio21";
+			drive-strength = <2>;
+			bias-disable;
+		};
+	};
+
+	mipi_1800_en: mipi-1800-en {
+		pinmux {
+			pins = "gpio86";
+			function = "gpio";
+		};
+
+		pinconf {
+			pins = "gpio86";
+			drive-strength = <2>;
+			bias-disable;
+		};
+	};
+
+	vdd_reset_1800: vdd-reset-1800 {
+		pinmux {
+			pins = "gpio87";
+			function = "gpio";
+		};
+
+		pinconf {
+			pins = "gpio87";
+			drive-strength = <2>;
+			bias-disable;
+		};
+	};
+};
diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi b/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi
index d4f4441179fc..eae22e6e97c1 100644
--- a/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor.dtsi
@@ -8,10 +8,12 @@
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/gpio-keys.h>
 #include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
 #include <dt-bindings/sound/sc7180-lpass.h>
 
-/* PMICs depend on spmi_bus label and so must come after SoC */
+#include "sc7180.dtsi"
+/* PMICs depend on spmi_bus label and so must come after sc7180.dtsi */
 #include "pm6150.dtsi"
 #include "pm6150l.dtsi"
 
@@ -42,6 +44,7 @@
  */
 
 /delete-node/ &hyp_mem;
+/delete-node/ &ipa_fw_mem;
 /delete-node/ &xbl_mem;
 /delete-node/ &aop_mem;
 /delete-node/ &sec_apps_mem;
@@ -144,6 +147,100 @@
 		vin-supply = <&ppvar_sys>;
 	};
 
+	pp1800_ec:
+	pp1800_sensors:
+	pp1800_ldo: pp1800-ldo-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "pp1800_ldo";
+
+		/* EC turns on with hibernate_l; always on for AP */
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+
+		/*
+		 * Actually should be pp1800_h1 but we don't have any need to
+		 * model that so we use the parent of pp1800_h1.
+		 */
+		vin-supply = <&pp3300_a>;
+	};
+
+	pp1800_uf_cam: pp1800-uf-cam-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "pp1800_uf_cam";
+		status = "disabled";
+
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+
+		gpio = <&tlmm 6 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&uf_cam_en>;
+
+		vin-supply = <&pp1800_ldo>;
+		regulator-enable-ramp-delay = <1000>;
+	};
+
+	pp1800_wf_cam: pp1800-wf-cam-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "pp1800_wf_cam";
+		status = "disabled";
+
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+
+		gpio = <&tlmm 7 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&wf_cam_en>;
+
+		vin-supply = <&pp1800_ldo>;
+		regulator-enable-ramp-delay = <1000>;
+	};
+
+	pp2800_uf_cam: pp2800-uf-cam-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "pp2800_uf_cam";
+		status = "disabled";
+
+		regulator-min-microvolt = <2850000>;
+		regulator-max-microvolt = <2850000>;
+
+		gpio = <&tlmm 6 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		/*
+		 * The pinconf can only be referenced once so we put it on the
+		 * first regulator and comment it out here.
+		 * pinctrl-names = "default";
+		 * pinctrl-0 = <&uf_cam_en>;
+		 */
+
+		vin-supply = <&pp3300_a>;
+	};
+
+	pp2800_vcm_wf_cam:
+	pp2800_wf_cam: pp2800-wf-cam-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "pp2800_wf_cam";
+		status = "disabled";
+
+		regulator-min-microvolt = <2850000>;
+		regulator-max-microvolt = <2850000>;
+
+		gpio = <&tlmm 7 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		/*
+		 * The pinconf can only be referenced once so we put it on the
+		 * first regulator and comment it out here.
+		 * pinctrl-names = "default";
+		 * pinctrl-0 = <&wf_cam_en>;
+		 */
+
+		vin-supply = <&pp3300_a>;
+	};
+
 	pp3300_audio:
 	pp3300_codec: pp3300-codec-regulator {
 		compatible = "regulator-fixed";
@@ -190,7 +287,7 @@
 		vin-supply = <&pp3300_a>;
 	};
 
-	pp3300_hub: pp3300-hub {
+	pp3300_hub: pp3300-hub-regulator {
 		compatible = "regulator-fixed";
 		regulator-name = "pp3300_hub";
 
@@ -202,7 +299,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&en_pp3300_hub>;
 
-		regulator-always-on;
+		/* The BIOS leaves this regulator on */
 		regulator-boot-on;
 
 		vin-supply = <&pp3300_a>;
@@ -235,7 +332,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pen_pdct_l>;
 
-		pen_insert: pen-insert {
+		pen_insert: switch-pen-insert {
 			label = "Pen Insert";
 
 			/* Insert = low, eject = high */
@@ -260,6 +357,7 @@
 		keyboard_backlight: keyboard-backlight {
 			status = "disabled";
 			label = "cros_ec::kbd_backlight";
+			function = LED_FUNCTION_KBD_BACKLIGHT;
 			pwms = <&cros_ec_pwm 0>;
 			max-brightness = <1023>;
 		};
@@ -532,7 +630,7 @@
 	};
 };
 
-&ap_ec_spi {
+ap_ec_spi: &spi6 {
 	status = "okay";
 	cros_ec: ec@0 {
 		compatible = "google,cros-ec-spi";
@@ -543,7 +641,7 @@
 		pinctrl-0 = <&ap_ec_int_l>;
 		spi-max-frequency = <3000000>;
 
-		cros_ec_pwm: ec-pwm {
+		cros_ec_pwm: pwm {
 			compatible = "google,cros-ec-pwm";
 			#pwm-cells = <1>;
 		};
@@ -581,7 +679,7 @@
 	};
 };
 
-&ap_h1_spi {
+ap_h1_spi: &spi0 {
 	status = "okay";
 	cr50: tpm@0 {
 		compatible = "google,cr50";
@@ -603,6 +701,10 @@
 	vdda-supply = <&vdda_mipi_dsi0_1p2>;
 };
 
+&dsi0_out {
+	data-lanes = <0 1 2 3>;
+};
+
 &dsi_phy {
 	status = "okay";
 	vdds-supply = <&vdda_mipi_dsi0_pll>;
@@ -624,13 +726,11 @@ ap_sar_sensor_i2c: &i2c5 {
 		vdd-supply = <&pp3300_a>;
 		svdd-supply = <&pp1800_prox>;
 
-		status = "disabled";
 		label = "proximity-wifi";
 	};
 };
 
 ap_tp_i2c: &i2c7 {
-	status = "okay";
 	clock-frequency = <400000>;
 
 	trackpad: trackpad@15 {
@@ -715,8 +815,6 @@ hp_i2c: &i2c9 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&dp_hot_plug_det>;
 	data-lanes = <0 1>;
-	vdda-1p2-supply = <&vdda_usb_ss_dp_1p2>;
-	vdda-0p9-supply = <&vdda_usb_ss_dp_core>;
 };
 
 &pm6150_adc {
@@ -806,7 +904,6 @@ ap_spi_fp: &spi10 {
 	};
 };
 
-#include <arm/cros-ec-keyboard.dtsi>
 #include <arm/cros-ec-sbs.dtsi>
 
 &uart3 {
@@ -839,6 +936,24 @@ ap_spi_fp: &spi10 {
 
 &usb_1_dwc3 {
 	dr_mode = "host";
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	/* 2.x hub on port 1 */
+	usb_hub_2_x: hub@1 {
+		compatible = "usbbda,5411";
+		reg = <1>;
+		vdd-supply = <&pp3300_hub>;
+		peer-hub = <&usb_hub_3_x>;
+	};
+
+	/* 3.x hub on port 2 */
+	usb_hub_3_x: hub@2 {
+		compatible = "usbbda,411";
+		reg = <2>;
+		vdd-supply = <&pp3300_hub>;
+		peer-hub = <&usb_hub_2_x>;
+	};
 };
 
 &usb_1_hsphy {
@@ -1517,4 +1632,32 @@ ap_spi_fp: &spi10 {
 			drive-strength = <2>;
 		};
 	};
+
+	uf_cam_en: uf-cam-en {
+		pinmux {
+			pins = "gpio6";
+			function = "gpio";
+		};
+
+		pinconf {
+			pins = "gpio6";
+			drive-strength = <2>;
+			/* External pull down */
+			bias-disable;
+		};
+	};
+
+	wf_cam_en: wf-cam-en {
+		pinmux {
+			pins = "gpio7";
+			function = "gpio";
+		};
+
+		pinconf {
+			pins = "gpio7";
+			drive-strength = <2>;
+			/* External pull down */
+			bias-disable;
+		};
+	};
 };
diff --git a/arch/arm64/boot/dts/qcom/sc7180.dtsi b/arch/arm64/boot/dts/qcom/sc7180.dtsi
index faf8b807d0ff..58976a1ba06b 100644
--- a/arch/arm64/boot/dts/qcom/sc7180.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7180.dtsi
@@ -398,7 +398,7 @@
 		};
 	};
 
-	cpu0_opp_table: cpu0_opp_table {
+	cpu0_opp_table: opp-table-cpu0 {
 		compatible = "operating-points-v2";
 		opp-shared;
 
@@ -453,7 +453,7 @@
 		};
 	};
 
-	cpu6_opp_table: cpu6_opp_table {
+	cpu6_opp_table: opp-table-cpu6 {
 		compatible = "operating-points-v2";
 		opp-shared;
 
@@ -555,12 +555,6 @@
 		};
 	};
 
-	tcsr_mutex: hwlock {
-		compatible = "qcom,tcsr-mutex";
-		syscon = <&tcsr_mutex_regs 0 0x1000>;
-		#hwlock-cells = <1>;
-	};
-
 	smem {
 		compatible = "qcom,smem";
 		memory-region = <&smem_mem>;
@@ -693,7 +687,7 @@
 			};
 		};
 
-		sdhc_1: sdhci@7c4000 {
+		sdhc_1: mmc@7c4000 {
 			compatible = "qcom,sc7180-sdhci", "qcom,sdhci-msm-v5";
 			reg = <0 0x7c4000 0 0x1000>,
 				<0 0x07c5000 0 0x1000>;
@@ -704,10 +698,10 @@
 					<GIC_SPI 644 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "hc_irq", "pwr_irq";
 
-			clocks = <&gcc GCC_SDCC1_APPS_CLK>,
-				 <&gcc GCC_SDCC1_AHB_CLK>,
+			clocks = <&gcc GCC_SDCC1_AHB_CLK>,
+				 <&gcc GCC_SDCC1_APPS_CLK>,
 				 <&rpmhcc RPMH_CXO_CLK>;
-			clock-names = "core", "iface", "xo";
+			clock-names = "iface", "core", "xo";
 			interconnects = <&aggre1_noc MASTER_EMMC 0 &mc_virt SLAVE_EBI1 0>,
 					<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_EMMC_CFG 0>;
 			interconnect-names = "sdhc-ddr","cpu-sdhc";
@@ -725,7 +719,7 @@
 
 			status = "disabled";
 
-			sdhc1_opp_table: sdhc1-opp-table {
+			sdhc1_opp_table: opp-table {
 				compatible = "operating-points-v2";
 
 				opp-100000000 {
@@ -744,7 +738,7 @@
 			};
 		};
 
-		qup_opp_table: qup-opp-table {
+		qup_opp_table: opp-table-qup {
 			compatible = "operating-points-v2";
 
 			opp-75000000 {
@@ -1421,13 +1415,6 @@
 			qcom,bcm-voters = <&apps_bcm_voter>;
 		};
 
-		ipa_virt: interconnect@1e00000 {
-			compatible = "qcom,sc7180-ipa-virt";
-			reg = <0 0x01e00000 0 0x1000>;
-			#interconnect-cells = <2>;
-			qcom,bcm-voters = <&apps_bcm_voter>;
-		};
-
 		ipa: ipa@1e40000 {
 			compatible = "qcom,sc7180-ipa";
 
@@ -1459,6 +1446,8 @@
 					     "imem",
 					     "config";
 
+			qcom,qmp = <&aoss_qmp>;
+
 			qcom,smem-states = <&ipa_smp2p_out 0>,
 					   <&ipa_smp2p_out 1>;
 			qcom,smem-state-names = "ipa-clock-enabled-valid",
@@ -1467,13 +1456,19 @@
 			status = "disabled";
 		};
 
-		tcsr_mutex_regs: syscon@1f40000 {
-			compatible = "syscon";
-			reg = <0 0x01f40000 0 0x40000>;
+		tcsr_mutex: hwlock@1f40000 {
+			compatible = "qcom,tcsr-mutex";
+			reg = <0 0x01f40000 0 0x20000>;
+			#hwlock-cells = <1>;
+		};
+
+		tcsr_regs_1: syscon@1f60000 {
+			compatible = "qcom,sc7180-tcsr", "syscon";
+			reg = <0 0x01f60000 0 0x20000>;
 		};
 
-		tcsr_regs: syscon@1fc0000 {
-			compatible = "syscon";
+		tcsr_regs_2: syscon@1fc0000 {
+			compatible = "qcom,sc7180-tcsr", "syscon";
 			reg = <0 0x01fc0000 0 0x40000>;
 		};
 
@@ -1937,8 +1932,8 @@
 				 <&pdc_reset PDC_MODEM_SYNC_RESET>;
 			reset-names = "mss_restart", "pdc_reset";
 
-			qcom,halt-regs = <&tcsr_mutex_regs 0x23000 0x25000 0x24000>;
-			qcom,spare-regs = <&tcsr_regs 0xb3e4>;
+			qcom,halt-regs = <&tcsr_regs_1 0x3000 0x5000 0x4000>;
+			qcom,spare-regs = <&tcsr_regs_2 0xb3e4>;
 
 			status = "disabled";
 
@@ -1952,7 +1947,6 @@
 
 		gpu: gpu@5000000 {
 			compatible = "qcom,adreno-618.0", "qcom,adreno";
-			#stream-id-cells = <16>;
 			reg = <0 0x05000000 0 0x40000>, <0 0x0509e000 0 0x1000>,
 				<0 0x05061000 0 0x800>;
 			reg-names = "kgsl_3d0_reg_memory", "cx_mem", "cx_dbgc";
@@ -2054,7 +2048,7 @@
 		};
 
 		gmu: gmu@506a000 {
-			compatible="qcom,adreno-gmu-618.0", "qcom,adreno-gmu";
+			compatible = "qcom,adreno-gmu-618.0", "qcom,adreno-gmu";
 			reg = <0 0x0506a000 0 0x31000>, <0 0x0b290000 0 0x10000>,
 				<0 0x0b490000 0 0x10000>;
 			reg-names = "gmu", "gmu_pdc", "gmu_pdc_seq";
@@ -2584,7 +2578,7 @@
 			};
 		};
 
-		sdhc_2: sdhci@8804000 {
+		sdhc_2: mmc@8804000 {
 			compatible = "qcom,sc7180-sdhci", "qcom,sdhci-msm-v5";
 			reg = <0 0x08804000 0 0x1000>;
 
@@ -2593,10 +2587,10 @@
 					<GIC_SPI 222 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "hc_irq", "pwr_irq";
 
-			clocks = <&gcc GCC_SDCC2_APPS_CLK>,
-				 <&gcc GCC_SDCC2_AHB_CLK>,
+			clocks = <&gcc GCC_SDCC2_AHB_CLK>,
+				 <&gcc GCC_SDCC2_APPS_CLK>,
 				 <&rpmhcc RPMH_CXO_CLK>;
-			clock-names = "core", "iface", "xo";
+			clock-names = "iface", "core", "xo";
 
 			interconnects = <&aggre1_noc MASTER_SDCC_2 0 &mc_virt SLAVE_EBI1 0>,
 					<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_SDCC_2 0>;
@@ -2608,7 +2602,7 @@
 
 			status = "disabled";
 
-			sdhc2_opp_table: sdhc2-opp-table {
+			sdhc2_opp_table: opp-table {
 				compatible = "operating-points-v2";
 
 				opp-100000000 {
@@ -2627,7 +2621,7 @@
 			};
 		};
 
-		qspi_opp_table: qspi-opp-table {
+		qspi_opp_table: opp-table-qspi {
 			compatible = "operating-points-v2";
 
 			opp-75000000 {
@@ -2761,10 +2755,13 @@
 			clocks = <&gcc GCC_CFG_NOC_USB3_PRIM_AXI_CLK>,
 				 <&gcc GCC_USB30_PRIM_MASTER_CLK>,
 				 <&gcc GCC_AGGRE_USB3_PRIM_AXI_CLK>,
-				 <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
-				 <&gcc GCC_USB30_PRIM_SLEEP_CLK>;
-			clock-names = "cfg_noc", "core", "iface", "mock_utmi",
-				      "sleep";
+				 <&gcc GCC_USB30_PRIM_SLEEP_CLK>,
+				 <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>;
+			clock-names = "cfg_noc",
+				      "core",
+				      "iface",
+				      "sleep",
+				      "mock_utmi";
 
 			assigned-clocks = <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
 					  <&gcc GCC_USB30_PRIM_MASTER_CLK>;
@@ -2785,7 +2782,7 @@
 					<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_USB3 0>;
 			interconnect-names = "usb-ddr", "apps-usb";
 
-			usb_1_dwc3: dwc3@a600000 {
+			usb_1_dwc3: usb@a600000 {
 				compatible = "snps,dwc3";
 				reg = <0 0x0a600000 0 0xe000>;
 				interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
@@ -2828,7 +2825,7 @@
 				compatible = "venus-encoder";
 			};
 
-			venus_opp_table: venus-opp-table {
+			venus_opp_table: opp-table {
 				compatible = "operating-points-v2";
 
 				opp-150000000 {
@@ -2899,9 +2896,6 @@
 				 <&dispcc DISP_CC_MDSS_MDP_CLK>;
 			clock-names = "iface", "ahb", "core";
 
-			assigned-clocks = <&dispcc DISP_CC_MDSS_MDP_CLK>;
-			assigned-clock-rates = <300000000>;
-
 			interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-controller;
 			#interrupt-cells = <1>;
@@ -2917,7 +2911,7 @@
 
 			status = "disabled";
 
-			mdp: mdp@ae01000 {
+			mdp: display-controller@ae01000 {
 				compatible = "qcom,sc7180-dpu";
 				reg = <0 0x0ae01000 0 0x8f000>,
 				      <0 0x0aeb0000 0 0x2008>;
@@ -2931,12 +2925,10 @@
 					 <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
 				clock-names = "bus", "iface", "rot", "lut", "core",
 					      "vsync";
-				assigned-clocks = <&dispcc DISP_CC_MDSS_MDP_CLK>,
-						  <&dispcc DISP_CC_MDSS_VSYNC_CLK>,
+				assigned-clocks = <&dispcc DISP_CC_MDSS_VSYNC_CLK>,
 						  <&dispcc DISP_CC_MDSS_ROT_CLK>,
 						  <&dispcc DISP_CC_MDSS_AHB_CLK>;
-				assigned-clock-rates = <300000000>,
-						       <19200000>,
+				assigned-clock-rates = <19200000>,
 						       <19200000>,
 						       <19200000>;
 				operating-points-v2 = <&mdp_opp_table>;
@@ -2966,7 +2958,7 @@
 					};
 				};
 
-				mdp_opp_table: mdp-opp-table {
+				mdp_opp_table: opp-table {
 					compatible = "operating-points-v2";
 
 					opp-200000000 {
@@ -3045,7 +3037,7 @@
 					};
 				};
 
-				dsi_opp_table: dsi-opp-table {
+				dsi_opp_table: opp-table {
 					compatible = "operating-points-v2";
 
 					opp-187500000 {
@@ -3088,7 +3080,11 @@
 				compatible = "qcom,sc7180-dp";
 				status = "disabled";
 
-				reg = <0 0x0ae90000 0 0x1400>;
+				reg = <0 0xae90000 0 0x200>,
+				      <0 0xae90200 0 0x200>,
+				      <0 0xae90400 0 0xc00>,
+				      <0 0xae91000 0 0x400>,
+				      <0 0xae91400 0 0x400>;
 
 				interrupt-parent = <&mdss>;
 				interrupts = <12>;
@@ -3100,7 +3096,6 @@
 					 <&dispcc DISP_CC_MDSS_DP_PIXEL_CLK>;
 				clock-names = "core_iface", "core_aux", "ctrl_link",
 					      "ctrl_link_iface", "stream_pixel";
-				#clock-cells = <1>;
 				assigned-clocks = <&dispcc DISP_CC_MDSS_DP_LINK_CLK_SRC>,
 						  <&dispcc DISP_CC_MDSS_DP_PIXEL_CLK_SRC>;
 				assigned-clock-parents = <&dp_phy 0>, <&dp_phy 1>;
@@ -3218,7 +3213,7 @@
 		};
 
 		aoss_qmp: power-controller@c300000 {
-			compatible = "qcom,sc7180-aoss-qmp";
+			compatible = "qcom,sc7180-aoss-qmp", "qcom,aoss-qmp";
 			reg = <0 0x0c300000 0 0x400>;
 			interrupts = <GIC_SPI 389 IRQ_TYPE_EDGE_RISING>;
 			mboxes = <&apss_shared 0>;
@@ -3250,8 +3245,8 @@
 			cell-index = <0>;
 		};
 
-		imem@146aa000 {
-			compatible = "simple-mfd";
+		sram@146aa000 {
+			compatible = "qcom,sc7180-imem", "syscon", "simple-mfd";
 			reg = <0 0x146aa000 0 0x2000>;
 
 			#address-cells = <1>;
@@ -3387,9 +3382,9 @@
 		};
 
 		timer@17c20000{
-			#address-cells = <2>;
-			#size-cells = <2>;
-			ranges;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0 0 0x20000000>;
 			compatible = "arm,armv7-timer-mem";
 			reg = <0 0x17c20000 0 0x1000>;
 
@@ -3397,49 +3392,49 @@
 				frame-number = <0>;
 				interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
 					     <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0 0x17c21000 0 0x1000>,
-				      <0 0x17c22000 0 0x1000>;
+				reg = <0x17c21000 0x1000>,
+				      <0x17c22000 0x1000>;
 			};
 
 			frame@17c23000 {
 				frame-number = <1>;
 				interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0 0x17c23000 0 0x1000>;
+				reg = <0x17c23000 0x1000>;
 				status = "disabled";
 			};
 
 			frame@17c25000 {
 				frame-number = <2>;
 				interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0 0x17c25000 0 0x1000>;
+				reg = <0x17c25000 0x1000>;
 				status = "disabled";
 			};
 
 			frame@17c27000 {
 				frame-number = <3>;
 				interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0 0x17c27000 0 0x1000>;
+				reg = <0x17c27000 0x1000>;
 				status = "disabled";
 			};
 
 			frame@17c29000 {
 				frame-number = <4>;
 				interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0 0x17c29000 0 0x1000>;
+				reg = <0x17c29000 0x1000>;
 				status = "disabled";
 			};
 
 			frame@17c2b000 {
 				frame-number = <5>;
 				interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0 0x17c2b000 0 0x1000>;
+				reg = <0x17c2b000 0x1000>;
 				status = "disabled";
 			};
 
 			frame@17c2d000 {
 				frame-number = <6>;
 				interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0 0x17c2d000 0 0x1000>;
+				reg = <0x17c2d000 0x1000>;
 				status = "disabled";
 			};
 		};
@@ -3521,7 +3516,7 @@
 				};
 			};
 
-			apps_bcm_voter: bcm_voter {
+			apps_bcm_voter: bcm-voter {
 				compatible = "qcom,bcm-voter";
 			};
 		};
@@ -3587,7 +3582,7 @@
 			compatible = "qcom,sc7180-lpass-cpu";
 
 			reg = <0 0x62d87000 0 0x68000>, <0 0x62f00000 0 0x29000>;
-			reg-names =  "lpass-hdmiif", "lpass-lpaif";
+			reg-names = "lpass-hdmiif", "lpass-lpaif";
 
 			iommus = <&apps_smmu 0x1020 0>,
 				<&apps_smmu 0x1021 0>,
diff --git a/arch/arm64/boot/dts/qcom/sc7280-chrome-common.dtsi b/arch/arm64/boot/dts/qcom/sc7280-chrome-common.dtsi
new file mode 100644
index 000000000000..25f31c81b2b7
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc7280-chrome-common.dtsi
@@ -0,0 +1,102 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * sc7280 fragment for devices with Chrome bootloader
+ *
+ * This file mainly tries to abstract out the memory protections put into
+ * place by the Chrome bootloader which are different than what's put into
+ * place by Qualcomm's typical bootloader. It also has a smattering of other
+ * things that will hold true for any conceivable Chrome design
+ *
+ * Copyright 2022 Google LLC.
+ */
+
+/*
+ * Reserved memory changes
+ *
+ * Delete all unused memory nodes and define the peripheral memory regions
+ * required by the setup for Chrome boards.
+ */
+
+/delete-node/ &hyp_mem;
+/delete-node/ &xbl_mem;
+/delete-node/ &reserved_xbl_uefi_log;
+/delete-node/ &sec_apps_mem;
+
+/ {
+	reserved-memory {
+		adsp_mem: memory@86700000 {
+			reg = <0x0 0x86700000 0x0 0x2800000>;
+			no-map;
+		};
+
+		camera_mem: memory@8ad00000 {
+			reg = <0x0 0x8ad00000 0x0 0x500000>;
+			no-map;
+		};
+
+		venus_mem: memory@8b200000 {
+			reg = <0x0 0x8b200000 0x0 0x500000>;
+			no-map;
+		};
+
+		mpss_mem: memory@8b800000 {
+			reg = <0x0 0x8b800000 0x0 0xf600000>;
+			no-map;
+		};
+
+		wpss_mem: memory@9ae00000 {
+			reg = <0x0 0x9ae00000 0x0 0x1900000>;
+			no-map;
+		};
+
+		mba_mem: memory@9c700000 {
+			reg = <0x0 0x9c700000 0x0 0x200000>;
+			no-map;
+		};
+	};
+};
+
+/* The PMIC PON code isn't compatible w/ how Chrome EC/BIOS handle things. */
+&pmk8350_pon {
+	status = "disabled";
+};
+
+/*
+ * Chrome designs always boot from SPI flash hooked up to the qspi.
+ *
+ * It's expected that all boards will support "dual SPI" at 37.5 MHz.
+ * If some boards need a different speed or have a package that allows
+ * Quad SPI together with WP then those boards can easily override.
+ */
+&qspi {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&qspi_clk>, <&qspi_cs0>, <&qspi_data01>;
+
+	spi_flash: flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+
+		spi-max-frequency = <37500000>;
+		spi-tx-bus-width = <2>;
+		spi-rx-bus-width = <2>;
+	};
+};
+
+&remoteproc_wpss {
+	status = "okay";
+	firmware-name = "ath11k/WCN6750/hw1.0/wpss.mdt";
+};
+
+/* Increase the size from 2.5MB to 8MB */
+&rmtfs_mem {
+	reg = <0x0 0x9c900000 0x0 0x800000>;
+};
+
+&wifi {
+	status = "okay";
+
+	wifi-firmware {
+		iommus = <&apps_smmu 0x1c02 0x1>;
+	};
+};
diff --git a/arch/arm64/boot/dts/qcom/sc7280-crd-r3.dts b/arch/arm64/boot/dts/qcom/sc7280-crd-r3.dts
new file mode 100644
index 000000000000..dddb505e220b
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc7280-crd-r3.dts
@@ -0,0 +1,145 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * sc7280 CRD board device tree source
+ *
+ * Copyright (c) 2021 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+/dts-v1/;
+
+#include "sc7280-idp.dtsi"
+#include "sc7280-idp-ec-h1.dtsi"
+
+/ {
+	model = "Qualcomm Technologies, Inc. sc7280 CRD platform (rev3 - 4)";
+	compatible = "qcom,sc7280-crd",
+		     "google,hoglin-rev3", "google,hoglin-rev4",
+		     "google,piglin-rev3", "google,piglin-rev4",
+		     "qcom,sc7280";
+
+	aliases {
+		serial0 = &uart5;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+};
+
+&apps_rsc {
+	pmg1110-regulators {
+		compatible = "qcom,pmg1110-rpmh-regulators";
+		qcom,pmic-id = "k";
+
+		vreg_s1k_1p0: smps1 {
+			regulator-min-microvolt = <1010000>;
+			regulator-max-microvolt = <1170000>;
+		};
+	};
+};
+
+ap_tp_i2c: &i2c0 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	trackpad: trackpad@15 {
+		compatible = "hid-over-i2c";
+		reg = <0x15>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&tp_int_odl>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
+
+		post-power-on-delay-ms = <20>;
+		hid-descr-addr = <0x0001>;
+		vdd-supply = <&vreg_l18b_1p8>;
+
+		wakeup-source;
+	};
+};
+
+ap_ts_pen_1v8: &i2c13 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	ap_ts: touchscreen@5c {
+		compatible = "hid-over-i2c";
+		reg = <0x5c>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&ts_int_l>, <&ts_reset_l>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <55 IRQ_TYPE_LEVEL_LOW>;
+
+		post-power-on-delay-ms = <500>;
+		hid-descr-addr = <0x0000>;
+
+		vdd-supply = <&vreg_l19b_1p8>;
+	};
+};
+
+&nvme_3v3_regulator {
+	gpio = <&tlmm 51 GPIO_ACTIVE_HIGH>;
+};
+
+&nvme_pwren {
+	pins = "gpio51";
+};
+
+&sound {
+	audio-routing =
+		"IN1_HPHL", "HPHL_OUT",
+		"IN2_HPHR", "HPHR_OUT",
+		"AMIC1", "MIC BIAS1",
+		"AMIC2", "MIC BIAS2",
+		"VA DMIC0", "MIC BIAS1",
+		"VA DMIC1", "MIC BIAS1",
+		"VA DMIC2", "MIC BIAS3",
+		"VA DMIC3", "MIC BIAS3",
+		"TX SWR_ADC0", "ADC1_OUTPUT",
+		"TX SWR_ADC1", "ADC2_OUTPUT",
+		"TX SWR_ADC2", "ADC3_OUTPUT",
+		"TX SWR_DMIC0", "DMIC1_OUTPUT",
+		"TX SWR_DMIC1", "DMIC2_OUTPUT",
+		"TX SWR_DMIC2", "DMIC3_OUTPUT",
+		"TX SWR_DMIC3", "DMIC4_OUTPUT",
+		"TX SWR_DMIC4", "DMIC5_OUTPUT",
+		"TX SWR_DMIC5", "DMIC6_OUTPUT",
+		"TX SWR_DMIC6", "DMIC7_OUTPUT",
+		"TX SWR_DMIC7", "DMIC8_OUTPUT";
+};
+
+&wcd9385 {
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&wcd_reset_n>, <&us_euro_hs_sel>;
+	pinctrl-1 = <&wcd_reset_n_sleep>, <&us_euro_hs_sel>;
+	us-euro-gpios = <&tlmm 81 GPIO_ACTIVE_HIGH>;
+};
+
+&tlmm {
+	tp_int_odl: tp-int-odl {
+		pins = "gpio7";
+		function = "gpio";
+		bias-disable;
+	};
+
+	ts_int_l: ts-int-l {
+		pins = "gpio55";
+		function = "gpio";
+		bias-pull-up;
+	};
+
+	ts_reset_l: ts-reset-l {
+		pins = "gpio54";
+		function = "gpio";
+		bias-disable;
+	};
+
+	us_euro_hs_sel: us-euro-hs-sel {
+		pins = "gpio81";
+		function = "gpio";
+		bias-pull-down;
+		drive-strength = <2>;
+	};
+};
diff --git a/arch/arm64/boot/dts/qcom/sc7280-herobrine-audio-wcd9385.dtsi b/arch/arm64/boot/dts/qcom/sc7280-herobrine-audio-wcd9385.dtsi
new file mode 100644
index 000000000000..c72e53aaf997
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc7280-herobrine-audio-wcd9385.dtsi
@@ -0,0 +1,239 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * sc7280 device tree source for boards using Max98360 and wcd9385 codec
+ *
+ * Copyright (c) 2022, The Linux Foundation. All rights reserved.
+ */
+
+/ {
+	/* BOARD-SPECIFIC TOP LEVEL NODES */
+	sound: sound {
+		compatible = "google,sc7280-herobrine";
+		model = "sc7280-wcd938x-max98360a-1mic";
+
+		audio-routing =
+			"IN1_HPHL", "HPHL_OUT",
+			"IN2_HPHR", "HPHR_OUT",
+			"AMIC1", "MIC BIAS1",
+			"AMIC2", "MIC BIAS2",
+			"VA DMIC0", "MIC BIAS1",
+			"VA DMIC1", "MIC BIAS1",
+			"VA DMIC2", "MIC BIAS3",
+			"VA DMIC3", "MIC BIAS3",
+			"TX SWR_ADC0", "ADC1_OUTPUT",
+			"TX SWR_ADC1", "ADC2_OUTPUT",
+			"TX SWR_ADC2", "ADC3_OUTPUT",
+			"TX SWR_DMIC0", "DMIC1_OUTPUT",
+			"TX SWR_DMIC1", "DMIC2_OUTPUT",
+			"TX SWR_DMIC2", "DMIC3_OUTPUT",
+			"TX SWR_DMIC3", "DMIC4_OUTPUT",
+			"TX SWR_DMIC4", "DMIC5_OUTPUT",
+			"TX SWR_DMIC5", "DMIC6_OUTPUT",
+			"TX SWR_DMIC6", "DMIC7_OUTPUT",
+			"TX SWR_DMIC7", "DMIC8_OUTPUT";
+
+		qcom,msm-mbhc-hphl-swh = <1>;
+		qcom,msm-mbhc-gnd-swh = <1>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+		#sound-dai-cells = <0>;
+
+		dai-link@0 {
+			link-name = "MAX98360A";
+			reg = <0>;
+
+			cpu {
+				sound-dai = <&lpass_cpu MI2S_SECONDARY>;
+			};
+
+			codec {
+				sound-dai = <&max98360a>;
+			};
+		};
+
+		dai-link@1 {
+			link-name = "DisplayPort";
+			reg = <1>;
+
+			cpu {
+				sound-dai = <&lpass_cpu LPASS_DP_RX>;
+			};
+
+			codec {
+				sound-dai = <&mdss_dp>;
+			};
+		};
+
+		dai-link@2 {
+			link-name = "WCD9385 Playback";
+			reg = <2>;
+
+			cpu {
+				sound-dai = <&lpass_cpu LPASS_CDC_DMA_RX0>;
+			};
+
+			codec {
+				sound-dai = <&wcd9385 0>, <&swr0 0>, <&lpass_rx_macro 0>;
+			};
+		};
+
+		dai-link@3 {
+			link-name = "WCD9385 Capture";
+			reg = <3>;
+
+			cpu {
+				sound-dai = <&lpass_cpu LPASS_CDC_DMA_TX3>;
+			};
+
+			codec {
+				sound-dai = <&wcd9385 1>, <&swr1 0>, <&lpass_tx_macro 0>;
+			};
+		};
+
+		dai-link@4 {
+			link-name = "DMIC";
+			reg = <4>;
+
+			cpu {
+				sound-dai = <&lpass_cpu LPASS_CDC_DMA_VA_TX0>;
+			};
+
+			codec {
+				sound-dai = <&lpass_va_macro 0>;
+			};
+		};
+	};
+};
+
+/* ADDITIONS TO NODES DEFINED IN PARENT DEVICE TREE FILES */
+
+&lpass_cpu {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&mi2s1_data0>, <&mi2s1_sclk>, <&mi2s1_ws>;
+
+	dai-link@1 {
+		reg = <MI2S_SECONDARY>;
+		qcom,playback-sd-lines = <0>;
+	};
+
+	dai-link@5 {
+		reg = <LPASS_DP_RX>;
+	};
+
+	dai-link@6 {
+		reg = <LPASS_CDC_DMA_RX0>;
+	};
+
+	dai-link@19 {
+		reg = <LPASS_CDC_DMA_TX3>;
+	};
+
+	dai-link@25 {
+		reg = <LPASS_CDC_DMA_VA_TX0>;
+	};
+};
+
+&lpass_rx_macro {
+	status = "okay";
+};
+
+&lpass_tx_macro {
+	status = "okay";
+};
+
+&lpass_va_macro {
+	status = "okay";
+};
+
+&swr0 {
+	status = "okay";
+};
+
+&swr1 {
+	status = "okay";
+};
+
+&wcd9385 {
+	status = "okay";
+};
+
+/* PINCTRL */
+
+&lpass_dmic01_clk {
+	drive-strength = <8>;
+	bias-disable;
+};
+
+&lpass_dmic01_clk_sleep {
+	drive-strength = <2>;
+};
+
+&lpass_dmic01_data {
+	bias-pull-down;
+};
+
+&lpass_dmic23_clk {
+	drive-strength = <8>;
+	bias-disable;
+};
+
+&lpass_dmic23_clk_sleep {
+	drive-strength = <2>;
+};
+
+&lpass_dmic23_data {
+	bias-pull-down;
+};
+
+&lpass_rx_swr_clk {
+	drive-strength = <2>;
+	slew-rate = <1>;
+	bias-disable;
+};
+
+&lpass_rx_swr_clk_sleep {
+	bias-pull-down;
+};
+
+&lpass_rx_swr_data {
+	drive-strength = <2>;
+	slew-rate = <1>;
+	bias-bus-hold;
+};
+
+&lpass_rx_swr_data_sleep {
+	bias-pull-down;
+};
+
+&lpass_tx_swr_clk {
+	drive-strength = <2>;
+	slew-rate = <1>;
+	bias-disable;
+};
+
+&lpass_tx_swr_clk_sleep {
+	bias-pull-down;
+};
+
+&lpass_tx_swr_data {
+	drive-strength = <2>;
+	slew-rate = <1>;
+	bias-bus-hold;
+};
+
+&mi2s1_data0 {
+	drive-strength = <6>;
+	bias-disable;
+};
+
+&mi2s1_sclk {
+	drive-strength = <6>;
+	bias-disable;
+};
+
+&mi2s1_ws {
+	drive-strength = <6>;
+};
diff --git a/arch/arm64/boot/dts/qcom/sc7280-herobrine-crd.dts b/arch/arm64/boot/dts/qcom/sc7280-herobrine-crd.dts
new file mode 100644
index 000000000000..f0f26af1e421
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc7280-herobrine-crd.dts
@@ -0,0 +1,376 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * sc7280 CRD 3+ board device tree source
+ *
+ * Copyright 2022 Google LLC.
+ */
+
+/dts-v1/;
+
+#include "sc7280-herobrine.dtsi"
+#include "sc7280-herobrine-audio-wcd9385.dtsi"
+#include "sc7280-herobrine-lte-sku.dtsi"
+
+/ {
+	model = "Qualcomm Technologies, Inc. sc7280 CRD platform (rev5+)";
+	compatible = "google,zoglin", "google,hoglin", "qcom,sc7280";
+
+	/* FIXED REGULATORS */
+
+	/*
+	 * On most herobrine boards PPVAR_SYS directly provides VREG_EDP_BL.
+	 * However, on CRD there's an extra regulator in the way. Since this
+	 * is expected to be uncommon, we'll leave the "vreg_edp_bl" label
+	 * in the baseboard herobrine.dtsi point at "ppvar_sys" and then
+	 * make a "_crd" specific version here.
+	 */
+	vreg_edp_bl_crd: vreg-edp-bl-crd-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vreg_edp_bl_crd";
+
+		gpio = <&pm8350c_gpios 6 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&edp_bl_reg_en>;
+
+		vin-supply = <&ppvar_sys>;
+	};
+};
+
+/* ADDITIONS TO NODES DEFINED IN PARENT DEVICE TREE FILES */
+
+&apps_rsc {
+	pmg1110-regulators {
+		compatible = "qcom,pmg1110-rpmh-regulators";
+		qcom,pmic-id = "k";
+
+		vreg_s1k_1p0: smps1 {
+			regulator-min-microvolt = <1010000>;
+			regulator-max-microvolt = <1170000>;
+		};
+	};
+};
+
+ap_tp_i2c: &i2c0 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	trackpad: trackpad@15 {
+		compatible = "hid-over-i2c";
+		reg = <0x15>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&tp_int_odl>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
+
+		post-power-on-delay-ms = <20>;
+		hid-descr-addr = <0x0001>;
+		vdd-supply = <&pp3300_z1>;
+
+		wakeup-source;
+	};
+};
+
+&ap_sar_sensor_i2c {
+	status = "okay";
+};
+
+&ap_sar_sensor0 {
+	status = "okay";
+};
+
+&ap_sar_sensor1 {
+	status = "okay";
+};
+
+ap_ts_pen_1v8: &i2c13 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	ap_ts: touchscreen@5c {
+		compatible = "hid-over-i2c";
+		reg = <0x5c>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&ts_int_conn>, <&ts_rst_conn>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <55 IRQ_TYPE_LEVEL_LOW>;
+
+		post-power-on-delay-ms = <500>;
+		hid-descr-addr = <0x0000>;
+
+		vdd-supply = <&pp3300_left_in_mlb>;
+	};
+};
+
+&mdss_edp {
+	status = "okay";
+};
+
+&mdss_edp_phy {
+	status = "okay";
+};
+
+/* For nvme */
+&pcie1 {
+	status = "okay";
+};
+
+/* For nvme */
+&pcie1_phy {
+	status = "okay";
+};
+
+&pm8350c_pwm_backlight {
+	power-supply = <&vreg_edp_bl_crd>;
+};
+
+/* For eMMC */
+&sdhc_1 {
+	status = "okay";
+};
+
+/* For SD Card */
+&sdhc_2 {
+	status = "okay";
+};
+
+/* PINCTRL - ADDITIONS TO NODES IN PARENT DEVICE TREE FILES */
+
+/*
+ * This pin goes to the display panel but then doesn't actually do anything
+ * on the panel itself (it doesn't connect to the touchscreen controller).
+ * We'll set a pullup here just to park the line.
+ */
+&ts_rst_conn {
+	bias-pull-up;
+};
+
+/* PINCTRL - BOARD-SPECIFIC */
+
+/*
+ * Methodology for gpio-line-names:
+ * - If a pin goes to CRD board and is named it gets that name.
+ * - If a pin goes to CRD board and is not named, it gets no name.
+ * - If a pin is totally internal to Qcard then it gets Qcard name.
+ * - If a pin is not hooked up on Qcard, it gets no name.
+ */
+
+&pm8350c_gpios {
+	gpio-line-names = "FLASH_STROBE_1",		/* 1 */
+			  "AP_SUSPEND",
+			  "PM8008_1_RST_N",
+			  "",
+			  "",
+			  "EDP_BL_REG_EN",
+			  "PMIC_EDP_BL_EN",
+			  "PMIC_EDP_BL_PWM",
+			  "";
+
+	edp_bl_reg_en: edp-bl-reg-en-state {
+		pins = "gpio6";
+		function = "normal";
+		bias-disable;
+		qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
+	};
+};
+
+&tlmm {
+	gpio-line-names = "AP_TP_I2C_SDA",		/* 0 */
+			  "AP_TP_I2C_SCL",
+			  "PCIE1_RESET_N",
+			  "PCIE1_WAKE_N",
+			  "APPS_I2C_SDA",
+			  "APPS_I2C_SCL",
+			  "",
+			  "TPAD_INT_N",
+			  "",
+			  "",
+
+			  "GNSS_L1_EN",			/* 10 */
+			  "GNSS_L5_EN",
+			  "QSPI_DATA_0",
+			  "QSPI_DATA_1",
+			  "QSPI_CLK",
+			  "QSPI_CS_N_1",
+			  /*
+			   * AP_FLASH_WP is crossystem ABI. Schematics call it
+			   * BIOS_FLASH_WP_L (the '_L' suffix is misleading, the
+			   * signal is active high).
+			   */
+			  "AP_FLASH_WP",
+			  "",
+			  "AP_EC_INT_N",
+			  "",
+
+			  "CAM0_RST_N",			/* 20 */
+			  "CAM1_RST_N",
+			  "SM_DBG_UART_TX",
+			  "SM_DBG_UART_RX",
+			  "",
+			  "PM8008_IRQ_1",
+			  "HOST2WLAN_SOL",
+			  "WLAN2HOST_SOL",
+			  "MOS_BT_UART_CTS",
+			  "MOS_BT_UART_RFR",
+
+			  "MOS_BT_UART_TX",		/* 30 */
+			  "MOS_BT_UART_RX",
+			  "",
+			  "HUB_RST",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+
+			  "EC_SPI_MISO_GPIO40",		/* 40 */
+			  "EC_SPI_MOSI_GPIO41",
+			  "EC_SPI_CLK_GPIO42",
+			  "EC_SPI_CS_GPIO43",
+			  "",
+			  "EARLY_EUD_EN",
+			  "",
+			  "DP_HOT_PLUG_DETECT",
+			  "AP_BRD_ID_0",
+			  "AP_BRD_ID_1",
+
+			  "AP_BRD_ID_2",		/* 50 */
+			  "NVME_PWR_REG_EN",
+			  "TS_I2C_SDA_CONN",
+			  "TS_I2C_CLK_CONN",
+			  "TS_RST_CONN",
+			  "TS_INT_CONN",
+			  "AP_I2C_TPM_SDA",
+			  "AP_I2C_TPM_SCL",
+			  "",
+			  "",
+
+			  "EDP_HOT_PLUG_DET_N",		/* 60 */
+			  "",
+			  "",
+			  "AMP_EN",
+			  "CAM0_MCLK_GPIO_64",
+			  "CAM1_MCLK_GPIO_65",
+			  "",
+			  "",
+			  "",
+			  "CCI_I2C_SDA0",
+
+			  "CCI_I2C_SCL0",		/* 70 */
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "PCIE1_CLK_REQ_N",
+
+			  "EN_PP3300_DX_EDP",		/* 80 */
+			  "US_EURO_HS_SEL",
+			  "FORCED_USB_BOOT",
+			  "WCD_RESET_N",
+			  "MOS_WLAN_EN",
+			  "MOS_BT_EN",
+			  "MOS_SW_CTRL",
+			  "MOS_PCIE0_RST",
+			  "MOS_PCIE0_CLKREQ_N",
+			  "MOS_PCIE0_WAKE_N",
+
+			  "MOS_LAA_AS_EN",		/* 90 */
+			  "SD_CARD_DET_CONN",
+			  "",
+			  "",
+			  "MOS_BT_WLAN_SLIMBUS_CLK",
+			  "MOS_BT_WLAN_SLIMBUS_DAT0",
+			  "",
+			  "",
+			  "",
+			  "",
+
+			  "",				/* 100 */
+			  "",
+			  "",
+			  "",
+			  "H1_AP_INT_N",
+			  "",
+			  "AMP_BCLK",
+			  "AMP_DIN",
+			  "AMP_LRCLK",
+			  "UIM1_DATA_GPIO_109",
+
+			  "UIM1_CLK_GPIO_110",		/* 110 */
+			  "UIM1_RESET_GPIO_111",
+			  "",
+			  "UIM1_DATA",
+			  "UIM1_CLK",
+			  "UIM1_RESET",
+			  "UIM1_PRESENT",
+			  "SDM_RFFE0_CLK",
+			  "SDM_RFFE0_DATA",
+			  "",
+
+			  "SDM_RFFE1_DATA",		/* 120 */
+			  "SC_GPIO_121",
+			  "FASTBOOT_SEL_1",
+			  "SC_GPIO_123",
+			  "FASTBOOT_SEL_2",
+			  "SM_RFFE4_CLK_GRFC_8",
+			  "SM_RFFE4_DATA_GRFC_9",
+			  "WLAN_COEX_UART1_RX",
+			  "WLAN_COEX_UART1_TX",
+			  "",
+
+			  "",				/* 130 */
+			  "",
+			  "",
+			  "SDR_QLINK_REQ",
+			  "SDR_QLINK_EN",
+			  "QLINK0_WMSS_RESET_N",
+			  "SMR526_QLINK1_REQ",
+			  "SMR526_QLINK1_EN",
+			  "SMR526_QLINK1_WMSS_RESET_N",
+			  "",
+
+			  "SAR1_INT_N",			/* 140 */
+			  "SAR0_INT_N",
+			  "",
+			  "",
+			  "WCD_SWR_TX_CLK",
+			  "WCD_SWR_TX_DATA0",
+			  "WCD_SWR_TX_DATA1",
+			  "WCD_SWR_RX_CLK",
+			  "WCD_SWR_RX_DATA0",
+			  "WCD_SWR_RX_DATA1",
+
+			  "DMIC01_CLK",			/* 150 */
+			  "DMIC01_DATA",
+			  "DMIC23_CLK",
+			  "DMIC23_DATA",
+			  "",
+			  "",
+			  "EC_IN_RW_N",
+			  "EN_PP3300_HUB",
+			  "WCD_SWR_TX_DATA2",
+			  "",
+
+			  "",				/* 160 */
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+
+			  "",				/* 170 */
+			  "MOS_BLE_UART_TX",
+			  "MOS_BLE_UART_RX",
+			  "";
+};
diff --git a/arch/arm64/boot/dts/qcom/sc7280-herobrine-evoker-r0.dts b/arch/arm64/boot/dts/qcom/sc7280-herobrine-evoker-r0.dts
new file mode 100644
index 000000000000..ccbe50b6249a
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc7280-herobrine-evoker-r0.dts
@@ -0,0 +1,333 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Google Evoker board device tree source
+ *
+ * Copyright 2022 Google LLC.
+ */
+
+/dts-v1/;
+
+#include "sc7280-herobrine.dtsi"
+
+/ {
+	model = "Google Evoker";
+	compatible = "google,evoker", "qcom,sc7280";
+};
+
+/*
+ * ADDITIONS TO FIXED REGULATORS DEFINED IN PARENT DEVICE TREE FILES
+ *
+ * Sort order matches the order in the parent files (parents before children).
+ */
+
+&pp3300_codec {
+	status = "okay";
+};
+
+/* ADDITIONS TO NODES DEFINED IN PARENT DEVICE TREE FILES */
+
+ap_tp_i2c: &i2c0 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	trackpad: trackpad@2c {
+		compatible = "hid-over-i2c";
+		reg = <0x2c>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&tp_int_odl>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
+
+		hid-descr-addr = <0x20>;
+		vcc-supply = <&pp3300_z1>;
+
+		wakeup-source;
+	};
+};
+
+ts_i2c: &i2c13 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	ap_ts: touchscreen@10 {
+		compatible = "elan,ekth6915";
+		reg = <0x10>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&ts_int_conn>, <&ts_rst_conn>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <55 IRQ_TYPE_LEVEL_LOW>;
+
+		reset-gpios = <&tlmm 54 GPIO_ACTIVE_LOW>;
+
+		vcc33-supply = <&ts_avdd>;
+	};
+};
+
+&ap_sar_sensor_i2c {
+	status = "okay";
+};
+
+&ap_sar_sensor0 {
+	status = "okay";
+};
+
+&ap_sar_sensor1 {
+	status = "okay";
+};
+
+&mdss_edp {
+	status = "okay";
+};
+
+&mdss_edp_phy {
+	status = "okay";
+};
+
+/* For nvme */
+&pcie1 {
+	status = "okay";
+};
+
+/* For nvme */
+&pcie1_phy {
+	status = "okay";
+};
+
+&pwmleds {
+	status = "okay";
+};
+
+/* For eMMC */
+&sdhc_1 {
+	status = "okay";
+};
+
+/* PINCTRL - ADDITIONS TO NODES IN PARENT DEVICE TREE FILES */
+
+&ts_rst_conn {
+	bias-disable;
+};
+
+/* PINCTRL - BOARD-SPECIFIC */
+
+/*
+ * Methodology for gpio-line-names:
+ * - If a pin goes to herobrine board and is named it gets that name.
+ * - If a pin goes to herobrine board and is not named, it gets no name.
+ * - If a pin is totally internal to Qcard then it gets Qcard name.
+ * - If a pin is not hooked up on Qcard, it gets no name.
+ */
+
+&pm8350c_gpios {
+	gpio-line-names = "FLASH_STROBE_1",		/* 1 */
+			  "AP_SUSPEND",
+			  "PM8008_1_RST_N",
+			  "",
+			  "",
+			  "",
+			  "PMIC_EDP_BL_EN",
+			  "PMIC_EDP_BL_PWM",
+			  "";
+};
+
+&tlmm {
+	gpio-line-names = "AP_TP_I2C_SDA",		/* 0 */
+			  "AP_TP_I2C_SCL",
+			  "SSD_RST_L",
+			  "PE_WAKE_ODL",
+			  "AP_SAR_SDA",
+			  "AP_SAR_SCL",
+			  "PRB_SC_GPIO_6",
+			  "TP_INT_ODL",
+			  "HP_I2C_SDA",
+			  "HP_I2C_SCL",
+
+			  "GNSS_L1_EN",			/* 10 */
+			  "GNSS_L5_EN",
+			  "SPI_AP_MOSI",
+			  "SPI_AP_MISO",
+			  "SPI_AP_CLK",
+			  "SPI_AP_CS0_L",
+			  /*
+			   * AP_FLASH_WP is crossystem ABI. Schematics
+			   * call it BIOS_FLASH_WP_OD.
+			   */
+			  "AP_FLASH_WP",
+			  "",
+			  "AP_EC_INT_L",
+			  "",
+
+			  "UF_CAM_RST_L",		/* 20 */
+			  "WF_CAM_RST_L",
+			  "UART_AP_TX_DBG_RX",
+			  "UART_DBG_TX_AP_RX",
+			  "",
+			  "PM8008_IRQ_1",
+			  "HOST2WLAN_SOL",
+			  "WLAN2HOST_SOL",
+			  "MOS_BT_UART_CTS",
+			  "MOS_BT_UART_RFR",
+
+			  "MOS_BT_UART_TX",		/* 30 */
+			  "MOS_BT_UART_RX",
+			  "PRB_SC_GPIO_32",
+			  "HUB_RST_L",
+			  "",
+			  "",
+			  "AP_SPI_FP_MISO",
+			  "AP_SPI_FP_MOSI",
+			  "AP_SPI_FP_CLK",
+			  "AP_SPI_FP_CS_L",
+
+			  "AP_EC_SPI_MISO",		/* 40 */
+			  "AP_EC_SPI_MOSI",
+			  "AP_EC_SPI_CLK",
+			  "AP_EC_SPI_CS_L",
+			  "LCM_RST_L",
+			  "EARLY_EUD_N",
+			  "",
+			  "DP_HOT_PLUG_DET",
+			  "IO_BRD_MLB_ID0",
+			  "IO_BRD_MLB_ID1",
+
+			  "IO_BRD_MLB_ID2",		/* 50 */
+			  "SSD_EN",
+			  "TS_I2C_SDA_CONN",
+			  "TS_I2C_CLK_CONN",
+			  "TS_RST_CONN",
+			  "TS_INT_CONN",
+			  "AP_I2C_TPM_SDA",
+			  "AP_I2C_TPM_SCL",
+			  "PRB_SC_GPIO_58",
+			  "PRB_SC_GPIO_59",
+
+			  "EDP_HOT_PLUG_DET_N",		/* 60 */
+			  "FP_TO_AP_IRQ_L",
+			  "",
+			  "AMP_EN",
+			  "CAM0_MCLK_GPIO_64",
+			  "CAM1_MCLK_GPIO_65",
+			  "WF_CAM_MCLK",
+			  "PRB_SC_GPIO_67",
+			  "FPMCU_BOOT0",
+			  "UF_CAM_SDA",
+
+			  "UF_CAM_SCL",			/* 70 */
+			  "",
+			  "",
+			  "WF_CAM_SDA",
+			  "WF_CAM_SCL",
+			  "",
+			  "",
+			  "EN_FP_RAILS",
+			  "FP_RST_L",
+			  "PCIE1_CLKREQ_ODL",
+
+			  "EN_PP3300_DX_EDP",		/* 80 */
+			  "SC_GPIO_81",
+			  "FORCED_USB_BOOT",
+			  "WCD_RESET_N",
+			  "MOS_WLAN_EN",
+			  "MOS_BT_EN",
+			  "MOS_SW_CTRL",
+			  "MOS_PCIE0_RST",
+			  "MOS_PCIE0_CLKREQ_N",
+			  "MOS_PCIE0_WAKE_N",
+
+			  "MOS_LAA_AS_EN",		/* 90 */
+			  "SD_CD_ODL",
+			  "",
+			  "",
+			  "MOS_BT_WLAN_SLIMBUS_CLK",
+			  "MOS_BT_WLAN_SLIMBUS_DAT0",
+			  "HP_MCLK",
+			  "HP_BCLK",
+			  "HP_DOUT",
+			  "HP_DIN",
+
+			  "HP_LRCLK",			/* 100 */
+			  "HP_IRQ",
+			  "",
+			  "",
+			  "GSC_AP_INT_ODL",
+			  "EN_PP3300_CODEC",
+			  "AMP_BCLK",
+			  "AMP_DIN",
+			  "AMP_LRCLK",
+			  "UIM1_DATA_GPIO_109",
+
+			  "UIM1_CLK_GPIO_110",		/* 110 */
+			  "UIM1_RESET_GPIO_111",
+			  "PRB_SC_GPIO_112",
+			  "UIM0_DATA",
+			  "UIM0_CLK",
+			  "UIM0_RST",
+			  "UIM0_PRESENT_ODL",
+			  "SDM_RFFE0_CLK",
+			  "SDM_RFFE0_DATA",
+			  "WF_CAM_EN",
+
+			  "FASTBOOT_SEL_0",		/* 120 */
+			  "SC_GPIO_121",
+			  "FASTBOOT_SEL_1",
+			  "SC_GPIO_123",
+			  "FASTBOOT_SEL_2",
+			  "SM_RFFE4_CLK_GRFC_8",
+			  "SM_RFFE4_DATA_GRFC_9",
+			  "WLAN_COEX_UART1_RX",
+			  "WLAN_COEX_UART1_TX",
+			  "PRB_SC_GPIO_129",
+
+			  "LCM_ID0",			/* 130 */
+			  "LCM_ID1",
+			  "",
+			  "SDR_QLINK_REQ",
+			  "SDR_QLINK_EN",
+			  "QLINK0_WMSS_RESET_N",
+			  "SMR526_QLINK1_REQ",
+			  "SMR526_QLINK1_EN",
+			  "SMR526_QLINK1_WMSS_RESET_N",
+			  "PRB_SC_GPIO_139",
+
+			  "SAR1_IRQ_ODL",		/* 140 */
+			  "SAR0_IRQ_ODL",
+			  "PRB_SC_GPIO_142",
+			  "",
+			  "WCD_SWR_TX_CLK",
+			  "WCD_SWR_TX_DATA0",
+			  "WCD_SWR_TX_DATA1",
+			  "WCD_SWR_RX_CLK",
+			  "WCD_SWR_RX_DATA0",
+			  "WCD_SWR_RX_DATA1",
+
+			  "DMIC01_CLK",			/* 150 */
+			  "DMIC01_DATA",
+			  "DMIC23_CLK",
+			  "DMIC23_DATA",
+			  "",
+			  "",
+			  "EC_IN_RW_ODL",
+			  "HUB_EN",
+			  "WCD_SWR_TX_DATA2",
+			  "",
+
+			  "",				/* 160 */
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+
+			  "",				/* 170 */
+			  "MOS_BLE_UART_TX",
+			  "MOS_BLE_UART_RX",
+			  "",
+			  "",
+			  "";
+};
diff --git a/arch/arm64/boot/dts/qcom/sc7280-herobrine-herobrine-r1.dts b/arch/arm64/boot/dts/qcom/sc7280-herobrine-herobrine-r1.dts
new file mode 100644
index 000000000000..c1a671968725
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc7280-herobrine-herobrine-r1.dts
@@ -0,0 +1,363 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Google Herobrine board device tree source
+ *
+ * Copyright 2022 Google LLC.
+ */
+
+/dts-v1/;
+
+#include "sc7280-herobrine.dtsi"
+#include "sc7280-herobrine-lte-sku.dtsi"
+
+/ {
+	model = "Google Herobrine (rev1+)";
+	compatible = "google,herobrine", "qcom,sc7280";
+};
+
+/*
+ * ADDITIONS TO FIXED REGULATORS DEFINED IN PARENT DEVICE TREE FILES
+ *
+ * Sort order matches the order in the parent files (parents before children).
+ */
+
+&pp3300_codec {
+	status = "okay";
+};
+
+&pp3300_fp_mcu {
+	status = "okay";
+};
+
+&pp2850_vcm_wf_cam {
+	status = "okay";
+};
+
+&pp2850_wf_cam {
+	status = "okay";
+};
+
+&pp1800_wf_cam {
+	status = "okay";
+};
+
+&pp1200_wf_cam {
+	status = "okay";
+};
+
+/* ADDITIONS TO NODES DEFINED IN PARENT DEVICE TREE FILES */
+
+&ap_spi_fp {
+	status = "okay";
+};
+
+/*
+ * Although the trackpad is really part of the herobrine baseboard, we'll
+ * put the actual definition in the board device tree since different boards
+ * might hook up different trackpads (or no i2c trackpad at all in the case
+ * of tablets / detachables).
+ */
+ap_tp_i2c: &i2c0 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	trackpad: trackpad@15 {
+		compatible = "elan,ekth3000";
+		reg = <0x15>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&tp_int_odl>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
+
+		vcc-supply = <&pp3300_z1>;
+
+		wakeup-source;
+	};
+};
+
+/*
+ * The touchscreen connector might come off the Qcard, at least in the case of
+ * eDP. Like the trackpad, we'll put it in the board device tree file since
+ * different boards have different touchscreens.
+ */
+ts_i2c: &i2c13 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	ap_ts: touchscreen@5c {
+		compatible = "hid-over-i2c";
+		reg = <0x5c>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&ts_int_conn>, <&ts_rst_conn>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <55 IRQ_TYPE_LEVEL_LOW>;
+
+		post-power-on-delay-ms = <500>;
+		hid-descr-addr = <0x0000>;
+
+		vdd-supply = <&ts_avdd>;
+	};
+};
+
+&mdss_edp {
+	status = "okay";
+};
+
+&mdss_edp_phy {
+	status = "okay";
+};
+
+/* For nvme */
+&pcie1 {
+	status = "okay";
+};
+
+/* For nvme */
+&pcie1_phy {
+	status = "okay";
+};
+
+/* For eMMC */
+&sdhc_1 {
+	status = "okay";
+};
+
+/* For SD Card */
+&sdhc_2 {
+	status = "okay";
+};
+
+/* PINCTRL - ADDITIONS TO NODES IN PARENT DEVICE TREE FILES */
+
+/*
+ * This pin goes to the display panel but then doesn't actually do anything
+ * on the panel itself (it doesn't connect to the touchscreen controller).
+ * We'll set a pullup here just to park the line.
+ */
+&ts_rst_conn {
+	bias-pull-up;
+};
+
+/* PINCTRL - BOARD-SPECIFIC */
+
+/*
+ * Methodology for gpio-line-names:
+ * - If a pin goes to herobrine board and is named it gets that name.
+ * - If a pin goes to herobrine board and is not named, it gets no name.
+ * - If a pin is totally internal to Qcard then it gets Qcard name.
+ * - If a pin is not hooked up on Qcard, it gets no name.
+ */
+
+&pm8350c_gpios {
+	gpio-line-names = "FLASH_STROBE_1",		/* 1 */
+			  "AP_SUSPEND",
+			  "PM8008_1_RST_N",
+			  "",
+			  "",
+			  "",
+			  "PMIC_EDP_BL_EN",
+			  "PMIC_EDP_BL_PWM",
+			  "";
+};
+
+&tlmm {
+	gpio-line-names = "AP_TP_I2C_SDA",		/* 0 */
+			  "AP_TP_I2C_SCL",
+			  "SSD_RST_L",
+			  "PE_WAKE_ODL",
+			  "AP_SAR_SDA",
+			  "AP_SAR_SCL",
+			  "PRB_SC_GPIO_6",
+			  "TP_INT_ODL",
+			  "HP_I2C_SDA",
+			  "HP_I2C_SCL",
+
+			  "GNSS_L1_EN",			/* 10 */
+			  "GNSS_L5_EN",
+			  "SPI_AP_MOSI",
+			  "SPI_AP_MISO",
+			  "SPI_AP_CLK",
+			  "SPI_AP_CS0_L",
+			  /*
+			   * AP_FLASH_WP is crossystem ABI. Schematics
+			   * call it BIOS_FLASH_WP_OD.
+			   */
+			  "AP_FLASH_WP",
+			  "",
+			  "AP_EC_INT_L",
+			  "",
+
+			  "UF_CAM_RST_L",		/* 20 */
+			  "WF_CAM_RST_L",
+			  "UART_AP_TX_DBG_RX",
+			  "UART_DBG_TX_AP_RX",
+			  "",
+			  "PM8008_IRQ_1",
+			  "HOST2WLAN_SOL",
+			  "WLAN2HOST_SOL",
+			  "MOS_BT_UART_CTS",
+			  "MOS_BT_UART_RFR",
+
+			  "MOS_BT_UART_TX",		/* 30 */
+			  "MOS_BT_UART_RX",
+			  "PRB_SC_GPIO_32",
+			  "HUB_RST_L",
+			  "",
+			  "",
+			  "AP_SPI_FP_MISO",
+			  "AP_SPI_FP_MOSI",
+			  "AP_SPI_FP_CLK",
+			  "AP_SPI_FP_CS_L",
+
+			  "AP_EC_SPI_MISO",		/* 40 */
+			  "AP_EC_SPI_MOSI",
+			  "AP_EC_SPI_CLK",
+			  "AP_EC_SPI_CS_L",
+			  "LCM_RST_L",
+			  "EARLY_EUD_N",
+			  "",
+			  "DP_HOT_PLUG_DET",
+			  "IO_BRD_MLB_ID0",
+			  "IO_BRD_MLB_ID1",
+
+			  "IO_BRD_MLB_ID2",		/* 50 */
+			  "SSD_EN",
+			  "TS_I2C_SDA_CONN",
+			  "TS_I2C_CLK_CONN",
+			  "TS_RST_CONN",
+			  "TS_INT_CONN",
+			  "AP_I2C_TPM_SDA",
+			  "AP_I2C_TPM_SCL",
+			  "PRB_SC_GPIO_58",
+			  "PRB_SC_GPIO_59",
+
+			  "EDP_HOT_PLUG_DET_N",		/* 60 */
+			  "FP_TO_AP_IRQ_L",
+			  "",
+			  "AMP_EN",
+			  "CAM0_MCLK_GPIO_64",
+			  "CAM1_MCLK_GPIO_65",
+			  "WF_CAM_MCLK",
+			  "PRB_SC_GPIO_67",
+			  "FPMCU_BOOT0",
+			  "UF_CAM_SDA",
+
+			  "UF_CAM_SCL",			/* 70 */
+			  "",
+			  "",
+			  "WF_CAM_SDA",
+			  "WF_CAM_SCL",
+			  "",
+			  "",
+			  "EN_FP_RAILS",
+			  "FP_RST_L",
+			  "PCIE1_CLKREQ_ODL",
+
+			  "EN_PP3300_DX_EDP",		/* 80 */
+			  "SC_GPIO_81",
+			  "FORCED_USB_BOOT",
+			  "WCD_RESET_N",
+			  "MOS_WLAN_EN",
+			  "MOS_BT_EN",
+			  "MOS_SW_CTRL",
+			  "MOS_PCIE0_RST",
+			  "MOS_PCIE0_CLKREQ_N",
+			  "MOS_PCIE0_WAKE_N",
+
+			  "MOS_LAA_AS_EN",		/* 90 */
+			  "SD_CD_ODL",
+			  "",
+			  "",
+			  "MOS_BT_WLAN_SLIMBUS_CLK",
+			  "MOS_BT_WLAN_SLIMBUS_DAT0",
+			  "HP_MCLK",
+			  "HP_BCLK",
+			  "HP_DOUT",
+			  "HP_DIN",
+
+			  "HP_LRCLK",			/* 100 */
+			  "HP_IRQ",
+			  "",
+			  "",
+			  "GSC_AP_INT_ODL",
+			  "EN_PP3300_CODEC",
+			  "AMP_BCLK",
+			  "AMP_DIN",
+			  "AMP_LRCLK",
+			  "UIM1_DATA_GPIO_109",
+
+			  "UIM1_CLK_GPIO_110",		/* 110 */
+			  "UIM1_RESET_GPIO_111",
+			  "PRB_SC_GPIO_112",
+			  "UIM0_DATA",
+			  "UIM0_CLK",
+			  "UIM0_RST",
+			  "UIM0_PRESENT_ODL",
+			  "SDM_RFFE0_CLK",
+			  "SDM_RFFE0_DATA",
+			  "WF_CAM_EN",
+
+			  "FASTBOOT_SEL_0",		/* 120 */
+			  "SC_GPIO_121",
+			  "FASTBOOT_SEL_1",
+			  "SC_GPIO_123",
+			  "FASTBOOT_SEL_2",
+			  "SM_RFFE4_CLK_GRFC_8",
+			  "SM_RFFE4_DATA_GRFC_9",
+			  "WLAN_COEX_UART1_RX",
+			  "WLAN_COEX_UART1_TX",
+			  "PRB_SC_GPIO_129",
+
+			  "LCM_ID0",			/* 130 */
+			  "LCM_ID1",
+			  "",
+			  "SDR_QLINK_REQ",
+			  "SDR_QLINK_EN",
+			  "QLINK0_WMSS_RESET_N",
+			  "SMR526_QLINK1_REQ",
+			  "SMR526_QLINK1_EN",
+			  "SMR526_QLINK1_WMSS_RESET_N",
+			  "PRB_SC_GPIO_139",
+
+			  "SAR1_IRQ_ODL",		/* 140 */
+			  "SAR0_IRQ_ODL",
+			  "PRB_SC_GPIO_142",
+			  "",
+			  "WCD_SWR_TX_CLK",
+			  "WCD_SWR_TX_DATA0",
+			  "WCD_SWR_TX_DATA1",
+			  "WCD_SWR_RX_CLK",
+			  "WCD_SWR_RX_DATA0",
+			  "WCD_SWR_RX_DATA1",
+
+			  "DMIC01_CLK",			/* 150 */
+			  "DMIC01_DATA",
+			  "DMIC23_CLK",
+			  "DMIC23_DATA",
+			  "",
+			  "",
+			  "EC_IN_RW_ODL",
+			  "HUB_EN",
+			  "WCD_SWR_TX_DATA2",
+			  "",
+
+			  "",				/* 160 */
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+
+			  "",				/* 170 */
+			  "MOS_BLE_UART_TX",
+			  "MOS_BLE_UART_RX",
+			  "",
+			  "",
+			  "";
+};
diff --git a/arch/arm64/boot/dts/qcom/sc7280-herobrine-lte-sku.dtsi b/arch/arm64/boot/dts/qcom/sc7280-herobrine-lte-sku.dtsi
new file mode 100644
index 000000000000..a92eeccd2b2a
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc7280-herobrine-lte-sku.dtsi
@@ -0,0 +1,17 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Google Herobrine dts fragment for LTE SKUs
+ *
+ * Copyright 2022 Google LLC.
+ */
+/* Modem setup is different on Chrome setups than typical Qualcomm setup */
+
+&remoteproc_mpss {
+	compatible = "qcom,sc7280-mss-pil";
+	iommus = <&apps_smmu 0x124 0x0>, <&apps_smmu 0x488 0x7>;
+	interconnects = <&mc_virt MASTER_LLCC 0 &mc_virt SLAVE_EBI1 0>;
+	memory-region = <&mba_mem>, <&mpss_mem>;
+	firmware-name = "qcom/sc7280-herobrine/modem/mba.mbn",
+			"qcom/sc7280-herobrine/modem/qdsp6sw.mbn";
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/qcom/sc7280-herobrine-villager-r0.dts b/arch/arm64/boot/dts/qcom/sc7280-herobrine-villager-r0.dts
new file mode 100644
index 000000000000..73e24cc55a09
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc7280-herobrine-villager-r0.dts
@@ -0,0 +1,16 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Google Villager board device tree source
+ *
+ * Copyright 2022 Google LLC.
+ */
+
+/dts-v1/;
+
+#include "sc7280-herobrine-villager.dtsi"
+#include "sc7280-herobrine-lte-sku.dtsi"
+
+/ {
+	model = "Google Villager (rev0)";
+	compatible = "google,villager-rev0", "qcom,sc7280";
+};
diff --git a/arch/arm64/boot/dts/qcom/sc7280-herobrine-villager-r1-lte.dts b/arch/arm64/boot/dts/qcom/sc7280-herobrine-villager-r1-lte.dts
new file mode 100644
index 000000000000..f1017809e5da
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc7280-herobrine-villager-r1-lte.dts
@@ -0,0 +1,14 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Google Villager board device tree source
+ *
+ * Copyright 2022 Google LLC.
+ */
+
+#include "sc7280-herobrine-villager-r1.dts"
+#include "sc7280-herobrine-lte-sku.dtsi"
+
+/ {
+	model = "Google Villager (rev1+) with LTE";
+	compatible = "google,villager-sku512", "qcom,sc7280";
+};
diff --git a/arch/arm64/boot/dts/qcom/sc7280-herobrine-villager-r1.dts b/arch/arm64/boot/dts/qcom/sc7280-herobrine-villager-r1.dts
new file mode 100644
index 000000000000..cfc648726930
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc7280-herobrine-villager-r1.dts
@@ -0,0 +1,43 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Google Villager board device tree source
+ *
+ * Copyright 2022 Google LLC.
+ */
+
+/dts-v1/;
+
+#include "sc7280-herobrine-villager.dtsi"
+#include "sc7280-herobrine-audio-wcd9385.dtsi"
+
+/ {
+	model = "Google Villager (rev1+)";
+	compatible = "google,villager", "qcom,sc7280";
+};
+
+&lpass_va_macro {
+	vdd-micb-supply = <&pp1800_l2c>;
+};
+
+&sound {
+	audio-routing =
+			"IN1_HPHL", "HPHL_OUT",
+			"IN2_HPHR", "HPHR_OUT",
+			"AMIC1", "MIC BIAS1",
+			"AMIC2", "MIC BIAS2",
+			"VA DMIC0", "vdd-micb",
+			"VA DMIC1", "vdd-micb",
+			"VA DMIC2", "vdd-micb",
+			"VA DMIC3", "vdd-micb",
+			"TX SWR_ADC0", "ADC1_OUTPUT",
+			"TX SWR_ADC1", "ADC2_OUTPUT",
+			"TX SWR_ADC2", "ADC3_OUTPUT",
+			"TX SWR_DMIC0", "DMIC1_OUTPUT",
+			"TX SWR_DMIC1", "DMIC2_OUTPUT",
+			"TX SWR_DMIC2", "DMIC3_OUTPUT",
+			"TX SWR_DMIC3", "DMIC4_OUTPUT",
+			"TX SWR_DMIC4", "DMIC5_OUTPUT",
+			"TX SWR_DMIC5", "DMIC6_OUTPUT",
+			"TX SWR_DMIC6", "DMIC7_OUTPUT",
+			"TX SWR_DMIC7", "DMIC8_OUTPUT";
+};
diff --git a/arch/arm64/boot/dts/qcom/sc7280-herobrine-villager.dtsi b/arch/arm64/boot/dts/qcom/sc7280-herobrine-villager.dtsi
new file mode 100644
index 000000000000..4566722bf4dd
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc7280-herobrine-villager.dtsi
@@ -0,0 +1,326 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Google Villager board device tree source
+ *
+ * Copyright 2022 Google LLC.
+ */
+
+#include "sc7280-herobrine.dtsi"
+
+/*
+ * ADDITIONS TO FIXED REGULATORS DEFINED IN PARENT DEVICE TREE FILES
+ *
+ * Sort order matches the order in the parent files (parents before children).
+ */
+
+&pp3300_codec {
+	status = "okay";
+};
+
+/* ADDITIONS TO NODES DEFINED IN PARENT DEVICE TREE FILES */
+
+ap_tp_i2c: &i2c0 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	trackpad: trackpad@2c {
+		compatible = "hid-over-i2c";
+		reg = <0x2c>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&tp_int_odl>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
+
+		hid-descr-addr = <0x20>;
+		vcc-supply = <&pp3300_z1>;
+
+		wakeup-source;
+	};
+};
+
+ts_i2c: &i2c13 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	ap_ts: touchscreen@10 {
+		compatible = "elan,ekth6915";
+		reg = <0x10>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&ts_int_conn>, <&ts_rst_conn>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <55 IRQ_TYPE_LEVEL_LOW>;
+
+		reset-gpios = <&tlmm 54 GPIO_ACTIVE_LOW>;
+
+		vcc33-supply = <&ts_avdd>;
+	};
+};
+
+&ap_sar_sensor_i2c {
+	status = "okay";
+};
+
+&ap_sar_sensor0 {
+	status = "okay";
+};
+
+&ap_sar_sensor1 {
+	status = "okay";
+};
+
+&mdss_edp {
+	status = "okay";
+};
+
+&mdss_edp_phy {
+	status = "okay";
+};
+
+/* For nvme */
+&pcie1 {
+	status = "okay";
+};
+
+/* For nvme */
+&pcie1_phy {
+	status = "okay";
+};
+
+&pwmleds {
+	status = "okay";
+};
+
+/* For eMMC */
+&sdhc_1 {
+	status = "okay";
+};
+
+/* PINCTRL - ADDITIONS TO NODES IN PARENT DEVICE TREE FILES */
+
+&ts_rst_conn {
+	bias-disable;
+};
+
+/* PINCTRL - BOARD-SPECIFIC */
+
+/*
+ * Methodology for gpio-line-names:
+ * - If a pin goes to herobrine board and is named it gets that name.
+ * - If a pin goes to herobrine board and is not named, it gets no name.
+ * - If a pin is totally internal to Qcard then it gets Qcard name.
+ * - If a pin is not hooked up on Qcard, it gets no name.
+ */
+
+&pm8350c_gpios {
+	gpio-line-names = "FLASH_STROBE_1",		/* 1 */
+			  "AP_SUSPEND",
+			  "PM8008_1_RST_N",
+			  "",
+			  "",
+			  "",
+			  "PMIC_EDP_BL_EN",
+			  "PMIC_EDP_BL_PWM",
+			  "";
+};
+
+&tlmm {
+	gpio-line-names = "AP_TP_I2C_SDA",		/* 0 */
+			  "AP_TP_I2C_SCL",
+			  "SSD_RST_L",
+			  "PE_WAKE_ODL",
+			  "AP_SAR_SDA",
+			  "AP_SAR_SCL",
+			  "PRB_SC_GPIO_6",
+			  "TP_INT_ODL",
+			  "HP_I2C_SDA",
+			  "HP_I2C_SCL",
+
+			  "GNSS_L1_EN",			/* 10 */
+			  "GNSS_L5_EN",
+			  "SPI_AP_MOSI",
+			  "SPI_AP_MISO",
+			  "SPI_AP_CLK",
+			  "SPI_AP_CS0_L",
+			  /*
+			   * AP_FLASH_WP is crossystem ABI. Schematics
+			   * call it BIOS_FLASH_WP_OD.
+			   */
+			  "AP_FLASH_WP",
+			  "",
+			  "AP_EC_INT_L",
+			  "",
+
+			  "UF_CAM_RST_L",		/* 20 */
+			  "WF_CAM_RST_L",
+			  "UART_AP_TX_DBG_RX",
+			  "UART_DBG_TX_AP_RX",
+			  "",
+			  "PM8008_IRQ_1",
+			  "HOST2WLAN_SOL",
+			  "WLAN2HOST_SOL",
+			  "MOS_BT_UART_CTS",
+			  "MOS_BT_UART_RFR",
+
+			  "MOS_BT_UART_TX",		/* 30 */
+			  "MOS_BT_UART_RX",
+			  "PRB_SC_GPIO_32",
+			  "HUB_RST_L",
+			  "",
+			  "",
+			  "AP_SPI_FP_MISO",
+			  "AP_SPI_FP_MOSI",
+			  "AP_SPI_FP_CLK",
+			  "AP_SPI_FP_CS_L",
+
+			  "AP_EC_SPI_MISO",		/* 40 */
+			  "AP_EC_SPI_MOSI",
+			  "AP_EC_SPI_CLK",
+			  "AP_EC_SPI_CS_L",
+			  "LCM_RST_L",
+			  "EARLY_EUD_N",
+			  "",
+			  "DP_HOT_PLUG_DET",
+			  "IO_BRD_MLB_ID0",
+			  "IO_BRD_MLB_ID1",
+
+			  "IO_BRD_MLB_ID2",		/* 50 */
+			  "SSD_EN",
+			  "TS_I2C_SDA_CONN",
+			  "TS_I2C_CLK_CONN",
+			  "TS_RST_CONN",
+			  "TS_INT_CONN",
+			  "AP_I2C_TPM_SDA",
+			  "AP_I2C_TPM_SCL",
+			  "PRB_SC_GPIO_58",
+			  "PRB_SC_GPIO_59",
+
+			  "EDP_HOT_PLUG_DET_N",		/* 60 */
+			  "FP_TO_AP_IRQ_L",
+			  "",
+			  "AMP_EN",
+			  "CAM0_MCLK_GPIO_64",
+			  "CAM1_MCLK_GPIO_65",
+			  "WF_CAM_MCLK",
+			  "PRB_SC_GPIO_67",
+			  "FPMCU_BOOT0",
+			  "UF_CAM_SDA",
+
+			  "UF_CAM_SCL",			/* 70 */
+			  "",
+			  "",
+			  "WF_CAM_SDA",
+			  "WF_CAM_SCL",
+			  "",
+			  "",
+			  "EN_FP_RAILS",
+			  "FP_RST_L",
+			  "PCIE1_CLKREQ_ODL",
+
+			  "EN_PP3300_DX_EDP",		/* 80 */
+			  "SC_GPIO_81",
+			  "FORCED_USB_BOOT",
+			  "WCD_RESET_N",
+			  "MOS_WLAN_EN",
+			  "MOS_BT_EN",
+			  "MOS_SW_CTRL",
+			  "MOS_PCIE0_RST",
+			  "MOS_PCIE0_CLKREQ_N",
+			  "MOS_PCIE0_WAKE_N",
+
+			  "MOS_LAA_AS_EN",		/* 90 */
+			  "SD_CD_ODL",
+			  "",
+			  "",
+			  "MOS_BT_WLAN_SLIMBUS_CLK",
+			  "MOS_BT_WLAN_SLIMBUS_DAT0",
+			  "HP_MCLK",
+			  "HP_BCLK",
+			  "HP_DOUT",
+			  "HP_DIN",
+
+			  "HP_LRCLK",			/* 100 */
+			  "HP_IRQ",
+			  "",
+			  "",
+			  "GSC_AP_INT_ODL",
+			  "EN_PP3300_CODEC",
+			  "AMP_BCLK",
+			  "AMP_DIN",
+			  "AMP_LRCLK",
+			  "UIM1_DATA_GPIO_109",
+
+			  "UIM1_CLK_GPIO_110",		/* 110 */
+			  "UIM1_RESET_GPIO_111",
+			  "PRB_SC_GPIO_112",
+			  "UIM0_DATA",
+			  "UIM0_CLK",
+			  "UIM0_RST",
+			  "UIM0_PRESENT_ODL",
+			  "SDM_RFFE0_CLK",
+			  "SDM_RFFE0_DATA",
+			  "WF_CAM_EN",
+
+			  "FASTBOOT_SEL_0",		/* 120 */
+			  "SC_GPIO_121",
+			  "FASTBOOT_SEL_1",
+			  "SC_GPIO_123",
+			  "FASTBOOT_SEL_2",
+			  "SM_RFFE4_CLK_GRFC_8",
+			  "SM_RFFE4_DATA_GRFC_9",
+			  "WLAN_COEX_UART1_RX",
+			  "WLAN_COEX_UART1_TX",
+			  "PRB_SC_GPIO_129",
+
+			  "LCM_ID0",			/* 130 */
+			  "LCM_ID1",
+			  "",
+			  "SDR_QLINK_REQ",
+			  "SDR_QLINK_EN",
+			  "QLINK0_WMSS_RESET_N",
+			  "SMR526_QLINK1_REQ",
+			  "SMR526_QLINK1_EN",
+			  "SMR526_QLINK1_WMSS_RESET_N",
+			  "PRB_SC_GPIO_139",
+
+			  "SAR1_IRQ_ODL",		/* 140 */
+			  "SAR0_IRQ_ODL",
+			  "PRB_SC_GPIO_142",
+			  "",
+			  "WCD_SWR_TX_CLK",
+			  "WCD_SWR_TX_DATA0",
+			  "WCD_SWR_TX_DATA1",
+			  "WCD_SWR_RX_CLK",
+			  "WCD_SWR_RX_DATA0",
+			  "WCD_SWR_RX_DATA1",
+
+			  "DMIC01_CLK",			/* 150 */
+			  "DMIC01_DATA",
+			  "DMIC23_CLK",
+			  "DMIC23_DATA",
+			  "",
+			  "",
+			  "EC_IN_RW_ODL",
+			  "HUB_EN",
+			  "WCD_SWR_TX_DATA2",
+			  "",
+
+			  "",				/* 160 */
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+
+			  "",				/* 170 */
+			  "MOS_BLE_UART_TX",
+			  "MOS_BLE_UART_RX",
+			  "",
+			  "",
+			  "";
+};
diff --git a/arch/arm64/boot/dts/qcom/sc7280-herobrine.dts b/arch/arm64/boot/dts/qcom/sc7280-herobrine.dts
deleted file mode 100644
index 7a92679a688b..000000000000
--- a/arch/arm64/boot/dts/qcom/sc7280-herobrine.dts
+++ /dev/null
@@ -1,14 +0,0 @@
-// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
-/*
- * Google Herobrine board device tree source
- *
- * Copyright 2021 Google LLC.
- */
-
-#include "sc7280-herobrine.dtsi"
-
-/ {
-	model = "Google Herobrine";
-	compatible = "google,herobrine",
-		     "qcom,sc7280";
-};
diff --git a/arch/arm64/boot/dts/qcom/sc7280-herobrine.dtsi b/arch/arm64/boot/dts/qcom/sc7280-herobrine.dtsi
index 4619fa9fcacd..c11e37160f34 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-herobrine.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280-herobrine.dtsi
@@ -1,87 +1,38 @@
 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
 /*
- * Google Herobrine board device tree source
+ * Google Herobrine baseboard device tree source
  *
- * Copyright 2021 Google LLC.
+ * The set of things in this file is a bit loosely defined. It's roughly
+ * defined as the set of things that the child boards happen to have in
+ * common. Since all of the child boards started from the same original
+ * design this is hopefully a large set of things but as more derivatives
+ * appear things may "bubble down" out of this file. For things that are
+ * part of the reference design but might not exist on child nodes we will
+ * follow the lead of the SoC dtsi files and leave their status as "disabled".
+ *
+ * Copyright 2022 Google LLC.
  */
 
-/dts-v1/;
-
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/iio/qcom,spmi-adc7-pmk8350.h>
-#include <dt-bindings/iio/qcom,spmi-adc7-pmr735a.h>
 #include <dt-bindings/input/gpio-keys.h>
 #include <dt-bindings/input/input.h>
-#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
-#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
-
-#include "sc7280.dtsi"
-
-/* PMICs depend on spmi_bus label and so must come after SoC */
-#include "pm7325.dtsi"
-#include "pm8350c.dtsi"
-#include "pmk8350.dtsi"
-
-/*
- * Reserved memory changes
- *
- * Delete all unused memory nodes and define the peripheral memory regions
- * required by the board dts.
- *
- */
-
-/delete-node/ &hyp_mem;
-/delete-node/ &xbl_mem;
-/delete-node/ &sec_apps_mem;
+#include <dt-bindings/leds/common.h>
 
-/* Increase the size from 2MB to 8MB */
-&rmtfs_mem {
-	reg = <0x0 0x83600000 0x0 0x800000>;
-};
+#include "sc7280-qcard.dtsi"
+#include "sc7280-chrome-common.dtsi"
 
 / {
-	reserved-memory {
-		adsp_mem: memory@86700000 {
-			reg = <0x0 0x86700000 0x0 0x2800000>;
-			no-map;
-		};
-
-		camera_mem: memory@8ad00000 {
-			reg = <0x0 0x8ad00000 0x0 0x500000>;
-			no-map;
-		};
-
-		venus_mem: memory@8b200000 {
-			reg = <0x0 0x8b200000 0x0 0x500000>;
-			no-map;
-		};
-
-		mpss_mem: memory@8b800000 {
-			reg = <0x0 0x8b800000 0x0 0xf600000>;
-			no-map;
-		};
-
-		wpss_mem: memory@9ae00000 {
-			reg = <0x0 0x9ae00000 0x0 0x1900000>;
-			no-map;
-		};
-
-		mba_mem: memory@9c700000 {
-			reg = <0x0 0x9c700000 0x0 0x200000>;
-			no-map;
-		};
-	};
-
-	aliases {
-		serial0 = &uart5;
-		serial1 = &uart7;
-	};
-
 	chosen {
 		stdout-path = "serial0:115200n8";
 	};
 
-	/* FIXED REGULATORS - parents above children */
+	/*
+	 * FIXED REGULATORS
+	 *
+	 * Sort order:
+	 * 1. parents above children.
+	 * 2. higher voltage above lower voltage.
+	 * 3. alphabetically by node name.
+	 */
 
 	/* This is the top level supply and variable voltage */
 	ppvar_sys: ppvar-sys-regulator {
@@ -103,11 +54,11 @@
 		vin-supply = <&ppvar_sys>;
 	};
 
-	pp5000_s3: pp5000-s3-regulator {
+	pp5000_s5: pp5000-s5-regulator {
 		compatible = "regulator-fixed";
-		regulator-name = "pp5000_s3";
+		regulator-name = "pp5000_s5";
 
-		/* EC turns on with en_pp5000_s3; always on for AP */
+		/* EC turns on with en_pp5000_s5; always on for AP */
 		regulator-always-on;
 		regulator-boot-on;
 		regulator-min-microvolt = <5000000>;
@@ -129,7 +80,6 @@
 		vin-supply = <&ppvar_sys>;
 	};
 
-	pp3300_audio:
 	pp3300_codec: pp3300-codec-regulator {
 		compatible = "regulator-fixed";
 		regulator-name = "pp3300_codec";
@@ -137,19 +87,18 @@
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
 
-		gpio = <&tlmm 67 GPIO_ACTIVE_HIGH>;
+		gpio = <&tlmm 105 GPIO_ACTIVE_HIGH>;
 		enable-active-high;
 		pinctrl-names = "default";
 		pinctrl-0 = <&en_pp3300_codec>;
 
 		vin-supply = <&pp3300_z1>;
+		status = "disabled";
 	};
 
-	pp3300_cam:
-	pp3300_edp:
-	pp3300_ts: pp3300-edp-regulator {
+	pp3300_left_in_mlb: pp3300-left-in-mlb-regulator {
 		compatible = "regulator-fixed";
-		regulator-name = "pp3300_edp";
+		regulator-name = "pp3300_left_in_mlb";
 
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
@@ -162,9 +111,9 @@
 		vin-supply = <&pp3300_z1>;
 	};
 
-	pp3300_fp:
+	pp3300_mcu_fp:
 	pp3300_fp_ls:
-	pp3300_mcu: pp3300-fp-regulator {
+	pp3300_fp_mcu: pp3300-fp-regulator {
 		compatible = "regulator-fixed";
 		regulator-name = "pp3300_fp";
 
@@ -175,7 +124,7 @@
 		regulator-always-on;
 
 		/*
-		 * WARNING: it is intentional that GPIO 42 isn't listed here.
+		 * WARNING: it is intentional that GPIO 77 isn't listed here.
 		 * The userspace script for updating the fingerprint firmware
 		 * needs to control the FP regulators during a FW update,
 		 * hence the signal can't be owned by the kernel regulator.
@@ -185,6 +134,7 @@
 		pinctrl-0 = <&en_fp_rails>;
 
 		vin-supply = <&pp3300_z1>;
+		status = "disabled";
 	};
 
 	pp3300_hub: pp3300-hub-regulator {
@@ -194,13 +144,13 @@
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
 
+		/* The BIOS leaves this regulator on */
 		regulator-boot-on;
-		regulator-always-on;
 
-		gpio = <&tlmm 24 GPIO_ACTIVE_HIGH>;
+		gpio = <&tlmm 157 GPIO_ACTIVE_HIGH>;
 		enable-active-high;
 		pinctrl-names = "default";
-		pinctrl-0 = <&en_pp3300_hub>;
+		pinctrl-0 = <&hub_en>;
 
 		vin-supply = <&pp3300_z1>;
 	};
@@ -219,44 +169,52 @@
 		vin-supply = <&pp3300_z1>;
 	};
 
-	pp2850_uf_cam: pp2850-uf-cam {
+	pp3300_ssd: pp3300-ssd-regulator {
 		compatible = "regulator-fixed";
-		regulator-name = "pp2850_uf_cam";
+		regulator-name = "pp3300_ssd";
 
-		regulator-min-microvolt = <2850000>;
-		regulator-max-microvolt = <2850000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
 
-		gpio = <&tlmm 6 GPIO_ACTIVE_HIGH>;
+		gpio = <&tlmm 51 GPIO_ACTIVE_HIGH>;
 		enable-active-high;
 		pinctrl-names = "default";
-		pinctrl-0 = <&uf_cam_en>;
+		pinctrl-0 = <&ssd_en>;
+
+		/*
+		 * The bootloaer may have left PCIe configured. Powering this
+		 * off while the PCIe clocks are still running isn't great,
+		 * so it's better to default to this regulator being on.
+		 */
+		regulator-boot-on;
 
-		vin-supply = <&pp3300_cam>;
+		vin-supply = <&pp3300_z1>;
 	};
 
-	pp2850_vcm_wf_cam: pp2850-vcm-wf-cam {
+	pp2850_vcm_wf_cam: pp2850-vcm-wf-cam-regulator {
 		compatible = "regulator-fixed";
 		regulator-name = "pp2850_vcm_wf_cam";
 
 		regulator-min-microvolt = <2850000>;
 		regulator-max-microvolt = <2850000>;
 
-		gpio = <&tlmm 7 GPIO_ACTIVE_HIGH>;
+		gpio = <&tlmm 119 GPIO_ACTIVE_HIGH>;
 		enable-active-high;
 		pinctrl-names = "default";
 		pinctrl-0 = <&wf_cam_en>;
 
-		vin-supply = <&pp3300_cam>;
+		vin-supply = <&pp3300_z1>;
+		status = "disabled";
 	};
 
-	pp2850_wf_cam: pp2850-wf-cam {
+	pp2850_wf_cam: pp2850-wf-cam-regulator {
 		compatible = "regulator-fixed";
 		regulator-name = "pp2850_wf_cam";
 
 		regulator-min-microvolt = <2850000>;
 		regulator-max-microvolt = <2850000>;
 
-		gpio = <&tlmm 7 GPIO_ACTIVE_HIGH>;
+		gpio = <&tlmm 119 GPIO_ACTIVE_HIGH>;
 		enable-active-high;
 		/*
 		 * The pinconf can only be referenced once so we put it on the
@@ -266,7 +224,8 @@
 		 * pinctrl-0 = <&wf_cam_en>;
 		 */
 
-		vin-supply = <&pp3300_cam>;
+		vin-supply = <&pp3300_z1>;
+		status = "disabled";
 	};
 
 	pp1800_fp: pp1800-fp-regulator {
@@ -280,7 +239,7 @@
 		regulator-always-on;
 
 		/*
-		 * WARNING: it is intentional that GPIO 42 isn't listed here.
+		 * WARNING: it is intentional that GPIO 77 isn't listed here.
 		 * The userspace script for updating the fingerprint firmware
 		 * needs to control the FP regulators during a FW update,
 		 * hence the signal can't be owned by the kernel regulator.
@@ -293,34 +252,14 @@
 		status = "disabled";
 	};
 
-	pp1800_uf_cam: pp1800-uf-cam {
-		compatible = "regulator-fixed";
-		regulator-name = "pp1800_uf_cam";
-
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <1800000>;
-
-		gpio = <&tlmm 6 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-		/*
-		 * The pinconf can only be referenced once so we put it on the
-		 * first regulator and comment it out here.
-		 *
-		 * pinctrl-names = "default";
-		 * pinctrl-0 = <&uf_cam_en>;
-		 */
-
-		vin-supply = <&pp1800_l19b>;
-	};
-
-	pp1800_wf_cam: pp1800-wf-cam {
+	pp1800_wf_cam: pp1800-wf-cam-regulator {
 		compatible = "regulator-fixed";
 		regulator-name = "pp1800_wf_cam";
 
 		regulator-min-microvolt = <1800000>;
 		regulator-max-microvolt = <1800000>;
 
-		gpio = <&tlmm 7 GPIO_ACTIVE_HIGH>;
+		gpio = <&tlmm 119 GPIO_ACTIVE_HIGH>;
 		enable-active-high;
 		/*
 		 * The pinconf can only be referenced once so we put it on the
@@ -330,17 +269,18 @@
 		 * pinctrl-0 = <&wf_cam_en>;
 		 */
 
-		vin-supply = <&pp1800_l19b>;
+		vin-supply = <&vreg_l19b_s0>;
+		status = "disabled";
 	};
 
-	pp1200_wf_cam: pp1200-wf-cam {
+	pp1200_wf_cam: pp1200-wf-cam-regulator {
 		compatible = "regulator-fixed";
 		regulator-name = "pp1200_wf_cam";
 
 		regulator-min-microvolt = <1200000>;
 		regulator-max-microvolt = <1200000>;
 
-		gpio = <&tlmm 7 GPIO_ACTIVE_HIGH>;
+		gpio = <&tlmm 119 GPIO_ACTIVE_HIGH>;
 		enable-active-high;
 		/*
 		 * The pinconf can only be referenced once so we put it on the
@@ -350,298 +290,135 @@
 		 * pinctrl-0 = <&wf_cam_en>;
 		 */
 
-		vin-supply = <&pp1200_l6b>;
+		vin-supply = <&pp3300_z1>;
+		status = "disabled";
 	};
 
 	/* BOARD-SPECIFIC TOP LEVEL NODES */
 
-	gpio_keys: gpio-keys {
-		compatible = "gpio-keys";
-		status = "disabled";
+	max98360a: audio-codec-0 {
+		compatible = "maxim,max98360a";
 		pinctrl-names = "default";
-		pinctrl-0 = <&pen_pdct_l>;
-
-		pen_insert: pen-insert {
-			label = "Pen Insert";
-
-			/* Insert = low, eject = high */
-			gpios = <&tlmm 39 GPIO_ACTIVE_LOW>;
-			linux,code = <SW_PEN_INSERTED>;
-			linux,input-type = <EV_SW>;
-			wakeup-event-action = <EV_ACT_DEASSERTED>;
-			wakeup-source;
-		};
+		pinctrl-0 = <&amp_en>;
+		sdmode-gpios = <&tlmm 63 GPIO_ACTIVE_HIGH>;
+		#sound-dai-cells = <0>;
 	};
 
-	pwmleds {
+	pwmleds: pwmleds {
 		compatible = "pwm-leds";
 		status = "disabled";
 		keyboard_backlight: keyboard-backlight {
-			status = "disabled";
 			label = "cros_ec::kbd_backlight";
+			function = LED_FUNCTION_KBD_BACKLIGHT;
 			pwms = <&cros_ec_pwm 0>;
 			max-brightness = <1023>;
 		};
 	};
 };
 
-&apps_rsc {
-	pm7325-regulators {
-		compatible = "qcom,pm7325-rpmh-regulators";
-		qcom,pmic-id = "b";
-
-		vdd19_pmu_pcie_i:
-		vdd19_pmu_rfa_i:
-		vreg_s1b_wlan:
-		vreg_s1b: smps1 {
-			regulator-min-microvolt = <1856000>;
-			regulator-max-microvolt = <2040000>;
-		};
-
-		vdd_pmu_aon_i:
-		vreg_s7b_wlan:
-		vreg_s7b: smps7 {
-			regulator-min-microvolt = <535000>;
-			regulator-max-microvolt = <1120000>;
-		};
+/*
+ * ADJUSTMENTS TO QCARD REGULATORS
+ *
+ * Mostly this is just board-local names for regulators that come from
+ * Qcard, but this also has some minor regulator overrides.
+ *
+ * Names are only listed here if regulators go somewhere other than a
+ * testpoint.
+ */
 
-		vdd13_pmu_pcie_i:
-		vdd13_pmu_rfa_i:
-		vreg_s8b_wlan:
-		vreg_s8b: smps8 {
-			regulator-min-microvolt = <1256000>;
-			regulator-max-microvolt = <1500000>;
-		};
+/* From Qcard to our board; ordered by PMIC-ID / rail number */
 
-		vdda_usb_ss_dp_core:
-		vreg_l1b: ldo1 {
-			regulator-min-microvolt = <825000>;
-			regulator-max-microvolt = <925000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-		};
+pp1256_s8b: &vreg_s8b_1p256 {};
 
-		vdda_usb_hs0_3p1:
-		vreg_l2b: ldo2 {
-			regulator-min-microvolt = <2700000>;
-			regulator-max-microvolt = <3544000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-		};
+pp1800_l18b_s0: &vreg_l18b_1p8 {};
+pp1800_l18b:    &vreg_l18b_1p8 {};
 
-		pp1200_l6b:
-		vdd_ufs_1p2:
-		vdd_vref:
-		vdda_csi01_1p2:
-		vdda_csi23_1p2:
-		vdda_csi4_1p2:
-		vdda_dsi0_1p2:
-		vdda_pcie0_1p2:
-		vdda_pcie1_1p2:
-		vdda_usb_ss_dp_1p2:
-		vdda_qlink0_1p2_ck:
-		vdda_qlink1_1p2_ck:
-		vreg_l6b_1p2:
-		vreg_l6b: ldo6 {
-			regulator-min-microvolt = <1120000>;
-			regulator-max-microvolt = <1408000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-		};
+vreg_l19b_s0: &vreg_l19b_1p8 {};
 
-		pp2950_l7b:
-		vreg_l7b: ldo7 {
-			regulator-min-microvolt = <2960000>;
-			regulator-max-microvolt = <2960000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-		};
+pp1800_alc5682: &vreg_l2c_1p8 {};
+pp1800_l2c:     &vreg_l2c_1p8 {};
 
-		codec_vcc:
-		pp1800_l18b_s0:
-		pp1800_ts:
-		vdd1:
-		vddpx_0:
-		vddpx_3:
-		vddpx_7:
-		vreg_l18b: ldo18 {
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <2000000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-		};
+vreg_l4c: &vreg_l4c_1p8_3p0 {};
 
-		pp1800_l19b:
-		vddpx_ts:
-		vddpx_wl4otp:
-		vreg_l19b: ldo19 {
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-		};
-	};
+ppvar_l6c: &vreg_l6c_2p96 {};
 
-	pm8350c-regulators {
-		compatible = "qcom,pm8350c-rpmh-regulators";
-		qcom,pmic-id = "c";
+pp3000_l7c: &vreg_l7c_3p0 {};
 
-		vreg_s1c: smps1 {
-			regulator-min-microvolt = <2190000>;
-			regulator-max-microvolt = <2210000>;
-		};
+pp1800_prox: &vreg_l8c_1p8 {};
+pp1800_l8c:  &vreg_l8c_1p8 {};
 
-		vddpx_1:
-		vreg_s9c: smps9 {
-			regulator-min-microvolt = <1010000>;
-			regulator-max-microvolt = <1170000>;
-		};
+pp2950_l9c: &vreg_l9c_2p96 {};
 
-		pp1800_l1c:
-		pp1800_pen:
-		vdd_a_gfx_cs_1p1:
-		vdd_a_cxo_1p8:
-		vdd_qfprom:
-		vdda_apc_cs_1p8:
-		vdda_qrefs_1p8:
-		vdda_turing_q6_cs_1p8:
-		vdda_usb_hs0_1p8:
-		vreg_l1c: ldo1 {
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1980000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-		};
+pp1800_lcm:  &vreg_l12c_1p8 {};
+pp1800_mipi: &vreg_l12c_1p8 {};
+pp1800_l12c: &vreg_l12c_1p8 {};
 
-		dmic_vdd:
-		pp1800_alc5682:
-		pp1800_l2c:
-		pp1800_vreg_alc5682:
-		vreg_l2c: ldo2 {
-			regulator-min-microvolt = <1620000>;
-			regulator-max-microvolt = <1980000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-		};
+pp3300_lcm:  &vreg_l13c_3p0 {};
+pp3300_mipi: &vreg_l13c_3p0 {};
+pp3300_l13c: &vreg_l13c_3p0 {};
 
-		pp3300_sar:
-		pp3300_sensor:
-		vreg_l3c: ldo3 {
-			regulator-min-microvolt = <2800000>;
-			regulator-max-microvolt = <3540000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-		};
+/* From our board to Qcard; ordered same as node definition above */
 
-		ppvar_uim1:
-		vddpx_5:
-		vreg_l4c: ldo4 {
-			regulator-min-microvolt = <1620000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-		};
+vreg_edp_bl: &ppvar_sys {};
 
-		pp2950_l5c:
-		uim_vcc:
-		vddpx_6:
-		vreg_l5c: ldo5 {
-			regulator-min-microvolt = <1620000>;
-			regulator-max-microvolt = <3300000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-		};
+ts_avdd:      &pp3300_left_in_mlb {};
+vreg_edp_3p3: &pp3300_left_in_mlb {};
 
-		ppvar_l6c:
-		vddpx_2:
-		vreg_l6c: ldo6 {
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <2950000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-		};
+/* Regulator overrides from Qcard */
 
-		vreg_l7c: ldo7 {
-			regulator-min-microvolt = <3000000>;
-			regulator-max-microvolt = <3544000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-		};
+/*
+ * Herobrine boards only use l2c to power an external audio codec (like
+ * alc5682) and we want that to be at 1.8V, not at some slightly lower voltage.
+ */
+&vreg_l2c_1p8 {
+	regulator-min-microvolt = <1800000>;
+};
 
-		pp1800_prox:
-		pp1800_sar:
-		vreg_l8c: ldo8 {
-			regulator-min-microvolt = <1620000>;
-			regulator-max-microvolt = <2000000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-		};
+/* ADDITIONS TO NODES DEFINED IN PARENT DEVICE TREE FILES */
 
-		pp2950_l9c:
-		vreg_l9c: ldo9 {
-			regulator-min-microvolt = <2960000>;
-			regulator-max-microvolt = <2960000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-		};
+&edp_panel {
+	/* Our board provides power to the qcard for the eDP panel. */
+	power-supply = <&vreg_edp_3p3>;
+};
 
-		vdd_a_gnss_0p9:
-		vdd_ufs_core:
-		vdd_usb_hs0_core:
-		vdd_vref_0p9:
-		vdda_csi01_0p9:
-		vdda_csi23_0p9:
-		vdda_csi4_0p9:
-		vdda_dsi0_pll_0p9:
-		vdda_dsi0_0p9:
-		vdda_pcie0_core:
-		vdda_pcie1_core:
-		vdda_qlink0_0p9:
-		vdda_qlink1_0p9:
-		vdda_qlink0_0p9_ck:
-		vdda_qlink1_0p9_ck:
-		vdda_qrefs_0p875:
-		vreg_l10c_0p8:
-		vreg_l10c: ldo10 {
-			regulator-min-microvolt = <720000>;
-			regulator-max-microvolt = <1050000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-		};
+ap_sar_sensor_i2c: &i2c1 {
+	clock-frequency = <400000>;
+	status = "disabled";
 
-		pp2800_l11c:
-		vreg_l11c: ldo11 {
-			regulator-min-microvolt = <2800000>;
-			regulator-max-microvolt = <3544000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-		};
+	ap_sar_sensor0: proximity@28 {
+		compatible = "semtech,sx9324";
+		reg = <0x28>;
+		#io-channel-cells = <1>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&sar0_irq_odl>;
 
-		pp1800_l12c:
-		vreg_l12c: ldo12 {
-			regulator-min-microvolt = <1650000>;
-			regulator-max-microvolt = <2000000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-		};
+		interrupt-parent = <&tlmm>;
+		interrupts = <141 IRQ_TYPE_LEVEL_LOW>;
 
-		pp3300_l13c:
-		vreg_l13c: ldo13 {
-			regulator-min-microvolt = <2700000>;
-			regulator-max-microvolt = <3544000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
-		};
+		vdd-supply = <&pp1800_prox>;
 
-		vreg_bob: bob {
-			regulator-min-microvolt = <3008000>;
-			regulator-max-microvolt = <3960000>;
-			regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>;
-		};
+		label = "proximity-wifi_cellular-0";
+		status = "disabled";
 	};
-};
 
-ap_tp_i2c: &i2c1 {
-	status = "okay";
-	clock-frequency = <400000>;
-
-	trackpad: trackpad@15 {
-		compatible = "elan,ekth3000";
-		reg = <0x15>;
+	ap_sar_sensor1: proximity@2c {
+		compatible = "semtech,sx9324";
+		reg = <0x2c>;
+		#io-channel-cells = <1>;
 		pinctrl-names = "default";
-		pinctrl-0 = <&tp_int_odl>;
+		pinctrl-0 = <&sar1_irq_odl>;
 
 		interrupt-parent = <&tlmm>;
-		interrupts = <102 IRQ_TYPE_EDGE_FALLING>;
+		interrupts = <140 IRQ_TYPE_LEVEL_LOW>;
 
-		vcc-supply = <&pp3300_z1>;
+		vdd-supply = <&pp1800_prox>;
 
-		wakeup-source;
+		label = "proximity-wifi_cellular-1";
+		status = "disabled";
 	};
 };
 
-ap_h1_i2c: &i2c12 {
+ap_i2c_tpm: &i2c14 {
 	status = "okay";
 	clock-frequency = <400000>;
 
@@ -650,80 +427,50 @@ ap_h1_i2c: &i2c12 {
 		reg = <0x50>;
 
 		pinctrl-names = "default";
-		pinctrl-0 = <&h1_ap_int_odl>;
+		pinctrl-0 = <&gsc_ap_int_odl>;
 
 		interrupt-parent = <&tlmm>;
-		interrupts = <54 IRQ_TYPE_EDGE_RISING>;
+		interrupts = <104 IRQ_TYPE_EDGE_RISING>;
 	};
 };
 
-ap_ts_pen: &i2c13 {
+&mdss {
 	status = "okay";
-	clock-frequency = <400000>;
-
-	ap_ts: touchscreen@10 {
-		compatible = "hid-over-i2c";
-		reg = <0x10>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&ts_int_l>, <&ts_reset_l>;
-
-		interrupt-parent = <&tlmm>;
-		interrupts = <81 IRQ_TYPE_LEVEL_LOW>;
-
-		post-power-on-delay-ms = <20>;
-		hid-descr-addr = <0x0001>;
-
-		vdd-supply = <&pp3300_ts>;
-	};
-};
-
-&pm7325_gpios {
-	status = "disabled"; /* No GPIOs are connected */
-};
-
-&pmk8350_gpios {
-	status = "disabled"; /* No GPIOs are connected */
 };
 
-&pmk8350_pon {
-	status = "disabled";
+&mdss_dp {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&dp_hot_plug_det>;
+	data-lanes = <0 1>;
 };
 
-&pmk8350_rtc {
-	status = "disabled";
+&mdss_mdp {
+	status = "okay";
 };
 
-&pmk8350_vadc {
-	pmk8350_die_temp {
-		reg = <PMK8350_ADC7_DIE_TEMP>;
-		label = "pmk8350_die_temp";
-		qcom,pre-scaling = <1 1>;
-	};
+/* NVMe drive, enabled on a per-board basis */
+&pcie1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie1_clkreq_n>, <&ssd_rst_l>, <&pe_wake_odl>;
 
-	pmr735a_die_temp {
-		reg = <PMR735A_ADC7_DIE_TEMP>;
-		label = "pmr735a_die_temp";
-		qcom,pre-scaling = <1 1>;
-	};
+	perst-gpios = <&tlmm 2 GPIO_ACTIVE_LOW>;
+	vddpe-3v3-supply = <&pp3300_ssd>;
 };
 
-&qfprom {
-	vcc-supply = <&vdd_qfprom>;
+&pm8350c_pwm {
+	status = "okay";
 };
 
-&qspi {
+&pm8350c_pwm_backlight {
 	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&qspi_clk>, <&qspi_cs0>, <&qspi_data01>;
 
-	flash@0 {
-		compatible = "jedec,spi-nor";
-		reg = <0>;
+	/* Our board provides power to the qcard for the backlight */
+	power-supply = <&vreg_edp_bl>;
+};
 
-		spi-max-frequency = <37500000>;
-		spi-tx-bus-width = <2>;
-		spi-rx-bus-width = <2>;
-	};
+&pmk8350_rtc {
+	status = "disabled";
 };
 
 &qupv3_id_0 {
@@ -734,44 +481,54 @@ ap_ts_pen: &i2c13 {
 	status = "okay";
 };
 
-&sdhc_1 {
-	status = "okay";
-
-	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&sdc1_on>;
-	pinctrl-1 = <&sdc1_off>;
-	vmmc-supply = <&pp2950_l7b>;
-	vqmmc-supply = <&pp1800_l19b>;
-};
-
+/* SD Card, enabled on a per-board basis */
 &sdhc_2 {
-	status = "okay";
+	pinctrl-0 = <&sdc2_clk>, <&sdc2_cmd>, <&sdc2_data>, <&sd_cd_odl>;
+	pinctrl-1 = <&sdc2_clk_sleep>, <&sdc2_cmd_sleep>, <&sdc2_data_sleep>, <&sd_cd_odl>;
 
-	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&sdc2_on>;
-	pinctrl-1 = <&sdc2_off>;
 	vmmc-supply = <&pp2950_l9c>;
 	vqmmc-supply = <&ppvar_l6c>;
 
 	cd-gpios = <&tlmm 91 GPIO_ACTIVE_LOW>;
 };
 
-ap_ec_spi: &spi8 {
+&spi_flash {
+	spi-max-frequency = <50000000>;
+};
+
+/* Fingerprint, enabled on a per-board basis */
+ap_spi_fp: &spi9 {
+	pinctrl-0 = <&qup_spi9_data_clk>, <&qup_spi9_cs_gpio_init_high>, <&qup_spi9_cs_gpio>;
+
+	cs-gpios = <&tlmm 39 GPIO_ACTIVE_LOW>;
+
+	cros_ec_fp: ec@0 {
+		compatible = "google,cros-ec-spi";
+		reg = <0>;
+		interrupt-parent = <&tlmm>;
+		interrupts = <61 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&fp_to_ap_irq_l>, <&fp_rst_l>, <&fpmcu_boot0>;
+		spi-max-frequency = <3000000>;
+	};
+};
+
+ap_ec_spi: &spi10 {
 	status = "okay";
+	pinctrl-0 = <&qup_spi10_data_clk>, <&qup_spi10_cs_gpio_init_high>, <&qup_spi10_cs_gpio>;
 
-	pinctrl-0 = <&qup_spi8_data_clk>, <&qup_spi8_cs_gpio_init_high>, <&qup_spi8_cs_gpio>;
-	cs-gpios = <&tlmm 35 GPIO_ACTIVE_LOW>;
+	cs-gpios = <&tlmm 43 GPIO_ACTIVE_LOW>;
 
 	cros_ec: ec@0 {
 		compatible = "google,cros-ec-spi";
 		reg = <0>;
 		interrupt-parent = <&tlmm>;
-		interrupts = <142 IRQ_TYPE_LEVEL_LOW>;
+		interrupts = <18 IRQ_TYPE_LEVEL_LOW>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&ap_ec_int_l>;
 		spi-max-frequency = <3000000>;
 
-		cros_ec_pwm: ec-pwm {
+		cros_ec_pwm: pwm {
 			compatible = "google,cros-ec-pwm";
 			#pwm-cells = <1>;
 		};
@@ -841,572 +598,300 @@ ap_ec_spi: &spi8 {
 	>;
 };
 
-&uart5 {
-	compatible = "qcom,geni-debug-uart";
-	status = "okay";
-};
-
-&uart7 {
-	status = "okay";
-};
-
 &usb_1 {
 	status = "okay";
 };
 
 &usb_1_dwc3 {
 	dr_mode = "host";
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	/* 2.x hub on port 1 */
+	usb_hub_2_x: hub@1 {
+		compatible = "usbbda,5411";
+		reg = <1>;
+		vdd-supply = <&pp3300_hub>;
+		peer-hub = <&usb_hub_3_x>;
+	};
+
+	/* 3.x hub on port 2 */
+	usb_hub_3_x: hub@2 {
+		compatible = "usbbda,411";
+		reg = <2>;
+		vdd-supply = <&pp3300_hub>;
+		peer-hub = <&usb_hub_2_x>;
+	};
 };
 
 &usb_1_hsphy {
 	status = "okay";
-
-	vdda-pll-supply = <&vdd_usb_hs0_core>;
-	vdda33-supply = <&vdda_usb_hs0_3p1>;
-	vdda18-supply = <&vdda_usb_hs0_1p8>;
 };
 
 &usb_1_qmpphy {
 	status = "okay";
-
-	vdda-phy-supply = <&vdda_usb_ss_dp_1p2>;
-	vdda-pll-supply = <&vdda_usb_ss_dp_core>;
 };
 
-&usb_2 {
-	status = "okay";
-};
+/* PINCTRL - ADDITIONS TO NODES IN PARENT DEVICE TREE FILES */
 
-&usb_2_dwc3 {
-	dr_mode = "host";
+&dp_hot_plug_det {
+	bias-disable;
 };
 
-&usb_2_hsphy {
-	status = "okay";
-
-	vdda-pll-supply = <&vdd_usb_hs0_core>;
-	vdda33-supply = <&vdda_usb_hs0_3p1>;
-	vdda18-supply = <&vdda_usb_hs0_1p8>;
+&pcie1_clkreq_n {
+	bias-pull-up;
+	drive-strength = <2>;
 };
 
-/* PINCTRL - additions to nodes defined in sc7280.dtsi */
-
 &qspi_cs0 {
 	bias-disable;
+	drive-strength = <8>;
 };
 
 &qspi_clk {
 	bias-disable;
+	drive-strength = <8>;
 };
 
 &qspi_data01 {
 	/* High-Z when no transfers; nice to park the lines */
 	bias-pull-up;
+	drive-strength = <8>;
 };
 
-&qup_uart5_rx {
+/* For ap_tp_i2c */
+&qup_i2c0_data_clk {
+	/* Has external pull */
+	bias-disable;
 	drive-strength = <2>;
-	bias-pull-up;
 };
 
-&qup_uart5_tx {
-	drive-strength = <2>;
+/* For ap_i2c_tpm */
+&qup_i2c14_data_clk {
+	/* Has external pull */
 	bias-disable;
+	drive-strength = <2>;
 };
 
-&qup_uart7_cts {
-	/*
-	 * Configure a pull-down on CTS to match the pull of
-	 * the Bluetooth module.
-	 */
-	bias-pull-down;
+/* For ap_spi_fp */
+&qup_spi9_data_clk {
+	bias-disable;
+	drive-strength = <2>;
 };
 
-&qup_uart7_rts {
-	/* We'll drive RTS, so no pull */
-	drive-strength = <2>;
+/* For ap_spi_fp */
+&qup_spi9_cs_gpio {
 	bias-disable;
+	drive-strength = <2>;
 };
 
-&qup_uart7_tx {
-	/* We'll drive TX, so no pull */
+/* For ap_ec_spi */
+&qup_spi10_data_clk {
+	bias-disable;
 	drive-strength = <2>;
+};
+
+/* For ap_ec_spi */
+&qup_spi10_cs_gpio {
 	bias-disable;
+	drive-strength = <2>;
 };
 
-&qup_uart7_rx {
-	/*
-	 * Configure a pull-up on RX. This is needed to avoid
-	 * garbage data when the TX pin of the Bluetooth module is
-	 * in tri-state (module powered off or not driving the
-	 * signal yet).
-	 */
+/* For uart_dbg */
+&qup_uart5_rx {
 	bias-pull-up;
 };
 
-&sdc1_on {
-	clk {
-		bias-disable;
-		drive-strength = <16>;
-	};
-
-	cmd {
-		bias-pull-up;
-		drive-strength = <10>;
-	};
-
-	data {
-		bias-pull-up;
-		drive-strength = <10>;
-	};
-
-	rclk {
-		bias-pull-down;
-	};
+/* For uart_dbg */
+&qup_uart5_tx {
+	bias-disable;
+	drive-strength = <2>;
 };
 
-&sdc2_on {
-	clk {
-		bias-disable;
-		drive-strength = <16>;
-	};
-
-	cmd {
-		bias-pull-up;
-		drive-strength = <10>;
-	};
+&sdc2_clk {
+	bias-disable;
+	drive-strength = <16>;
+};
 
-	data {
-		bias-pull-up;
-		drive-strength = <10>;
-	};
+&sdc2_cmd {
+	bias-pull-up;
+	drive-strength = <10>;
+};
 
-	sd-cd {
-		pins = "gpio91";
-		bias-pull-up;
-	};
+&sdc2_data {
+	bias-pull-up;
+	drive-strength = <10>;
 };
 
 /* PINCTRL - board-specific pinctrl */
 
-&pm8350c_gpios {
-	gpio-line-names = "AP_SUSPEND",
-			  "",
-			  "",
-			  "AP_BL_EN",
-			  "",
-			  "SD_CD_ODL",
-			  "",
-			  "",
-			  "AP_BL_PWM";
-
-	ap_bl_en: ap-bl-en {
-		pins = "gpio4";
-		function = "normal";
-		qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
-		bias-disable;
+&pm7325_gpios {
+	/*
+	 * On a quick glance it might look like KYPD_VOL_UP_N is used, but
+	 * that only passes through to a debug connector and not to the actual
+	 * volume up key.
+	 */
+	status = "disabled"; /* No GPIOs are connected */
+};
 
-		/* Force backlight to be disabled to match state at boot. */
-		output-low;
-	};
+&pmk8350_gpios {
+	status = "disabled"; /* No GPIOs are connected */
 };
 
 &tlmm {
-	gpio-line-names = "HP_I2C_SDA",			/* 0 */
-			  "HP_I2C_SCL",
-			  "SSD_RST_L",
-			  "PE_WAKE_ODL",
-			  "AP_TP_I2C_SDA",
-			  "AP_TP_I2C_SCL",
-			  "UF_CAM_EN",
-			  "WF_CAM_EN",
-			  "AP_SAR_SENSOR_SDA",
-			  "AP_SAR_SENSOR_SCL",
-
-			  "",				/* 10 */
-			  "",
-			  "AP_SPI_MOSI",
-			  "AP_SPI_MISO",
-			  "AP_SPI_CLK",
-			  "AP_SPI_CS0_L",
-			  "",
-			  "",
-			  "EDP_HPD",
-			  "",
-
-			  "UF_CAM_RST_L",		/* 20 */
-			  "WF_CAM_RST_L",
-			  "UART_AP_TX_DBG_RX",
-			  "UART_DBG_TX_AP_RX",
-			  "EN_PP3300_HUB",
-			  "",
-			  "HOST2WLAN_SOL",
-			  "WLAN2HOST_SOL",
-			  "BT_UART_CTS",
-			  "BT_UART_RTS",
-
-			  "BT_UART_TXD",		/* 30 */
-			  "BT_UART_RXD",
-			  "AP_EC_SPI_MISO",
-			  "AP_EC_SPI_MOSI",
-			  "AP_EC_SPI_CLK",
-			  "AP_EC_SPI_CS_L",
-			  "",
-			  "",
-			  "",
-			  "PEN_PDCT_L",
-
-			  "IO_BRD_ID0",			/* 40 */
-			  "IO_BRD_ID1",
-			  "EN_FP_RAILS",
-			  "PEN_IRQ_L",
-			  "AP_SPI_FP_MISO",
-			  "AP_SPI_FP_MOSI",
-			  "AP_SPI_FP_CLK",
-			  "AP_SPI_FP_CS_L",
-			  "AP_H1_SPI_MISO",
-			  "AP_H1_SPI_MOSI",
-
-			  "AP_H1_SPI_CLK",		/* 50 */
-			  "AP_H1_SPI_CS_L",
-			  "AP_TS_PEN_I2C_SDA",
-			  "AP_TS_PEN_I2C_SCL",
-			  "H1_AP_INT_ODL",
-			  "",
-			  "LCM_RST_1V8_L",
-			  "AMP_EN",
-			  "",
-			  "DP_HOT_PLUG_DET",
-
-			  "HUB_RST_L",			/* 60 */
-			  "FP_TO_AP_IRQ_L",
-			  "",
-			  "",
-			  "UF_CAM_MCLK",
-			  "WF_CAM_MCLK",
-			  "IO_BRD_ID2",
-			  "EN_PP3300_CODEC",
-			  "EC_IN_RW_ODL",
-			  "UF_CAM_SDA",
-
-			  "UF_CAM_SCL",			/* 70 */
-			  "WF_CAM_SDA",
-			  "WF_CAM_SCL",
-			  "AP_BRD_ID0",
-			  "AP_BRD_ID1",
-			  "AP_BRD_ID2",
-			  "",
-			  "FPMCU_BOOT0",
-			  "FP_RST_L",
-			  "PE_CLKREQ_ODL",
-
-			  "EN_EDP_PP3300",		/* 80 */
-			  "TS_INT_L",
-			  "FORCE_USB_BOOT",
-			  "WCD_RST_L",
-			  "WLAN_EN",
-			  "BT_EN",
-			  "WLAN_SW_CTRL",
-			  "PCIE0_RESET_L",
-			  "PCIE0_CLK_REQ_L",
-			  "PCIE0_WAKE_L",
-
-			  "AS_EN",			/* 90 */
-			  "SD_CD_ODL",
-			  "",
-			  /*
-			   * AP_FLASH_WP_L is crossystem ABI. Schematics
-			   * call it BIOS_FLASH_WP_L.
-			   */
-			  "AP_FLASH_WP_L",
-			  "BT_WLAN_SB_CLK",
-			  "BT_WLAN_SB_DATA",
-			  "HP_MCLK",
-			  "HP_BCLK",
-			  "HP_DOUT",
-			  "HP_DIN",
-
-			  "HP_LRCLK",			/* 100 */
-			  "HP_IRQ",
-			  "TP_INT_ODL",
-			  "",
-			  "IO_SKU_ID2",
-			  "TS_RESET_L",
-			  "AMP_BCLK",
-			  "AMP_DIN",
-			  "AMP_LRCLK",
-			  "UIM2_DATA",
-
-			  "UIM2_CLK",			/* 110 */
-			  "UIM2_RST",
-			  "UIM2_PRESENT",
-			  "UIM1_DATA",
-			  "UIM1_CLK",
-			  "UIM1_RST",
-			  "",
-			  "RFFE0_CLK",
-			  "RFFE0_DATA/BOOT_CONFIG_0",
-			  "RFFE1_CLK",
-
-			  "RFFE1_DATA/BOOT_CONFIG_1",	/* 120 */
-			  "RFFE2_CLK",
-			  "RFFE2_DATA/BOOT_CONFIG_2",
-			  "RFFE3_CLK",
-			  "RFFE3_DATA/BOOT_CONFIG_3",
-			  "RFFE4_CLK",
-			  "RFFE4_DATA",
-			  "WCI2_LTE_COEX_RXD",
-			  "WCI2_LTE_COEX_TXD",
-			  "IO_SKU_ID0",
-
-			  "IO_SKU_ID1",			/* 130 */
-			  "",
-			  "",
-			  "QLINK0_REQ",
-			  "QLINK0_EN",
-			  "QLINK0_WMSS_RESET_L",
-			  "QLINK1_REQ",
-			  "QLINK1_EN",
-			  "QLINK1_WMSS_RESET_L",
-			  "FORCED_USB_BOOT_POL",
-
-			  "",				/* 140 */
-			  "P_SENSOR_INT_L",
-			  "AP_EC_INT_L",
-			  "",
-			  "WCD_SWR_TX_CLK",
-			  "WCD_SWR_TX_DATA_0",
-			  "WCD_SWR_TX_DATA_1",
-			  "WCD_SWR_RX_CLK",
-			  "WCD_SWR_RX_DATA_0",
-			  "WCD_SWR_RX_DATA_1",
-
-			  "",				/* 150 */
-			  "",
-			  "",
-			  "",
-			  "",
-			  "",
-			  "",
-			  "",
-			  "WCD_SWR_TX_DATA_2",
-			  "",
-
-			  "",				/* 160 */
-			  "",
-			  "",
-			  "",
-			  "",
-			  "",
-			  "",
-			  "",
-			  "",
-			  "",
-
-			  "",				/* 170 */
-			  "SENS_UART_TXD",
-			  "SENS_UART_RXD",
-			  "",
-			  "",
-			  "";
-
-	/*
-	 * pinctrl settings for pins that have no real owners.
-	 */
+	/* pinctrl settings for pins that have no real owners. */
 	pinctrl-names = "default";
-	pinctrl-0 = <&bios_flash_wp_l>;
+	pinctrl-0 = <&bios_flash_wp_od>;
 
-	amp_en: amp-en {
-		pins = "gpio57";
+	amp_en: amp-en-pins {
+		pins = "gpio63";
 		function = "gpio";
-		bias-pull-down;
+		bias-disable;
+		drive-strength = <2>;
 	};
 
-	ap_ec_int_l: ap-ec-int-l {
-		pins = "gpio142";
-		input-enable;
+	ap_ec_int_l: ap-ec-int-l-pins {
+		pins = "gpio18";
+		function = "gpio";
 		bias-pull-up;
 	};
 
-	bios_flash_wp_l: bios-flash-wp-l {
-		pins = "gpio93";
+	bios_flash_wp_od: bios-flash-wp-od-pins {
+		pins = "gpio16";
 		function = "gpio";
-		input-enable;
+		/* Has external pull */
 		bias-disable;
 	};
 
-	bt_en: bt-en {
-		pins = "gpio85";
+	en_fp_rails: en-fp-rails-pins {
+		pins = "gpio77";
 		function = "gpio";
-		drive-strength = <2>;
-		output-low;
-		bias-pull-down;
-	};
-
-	en_fp_rails: en-fp-rails {
-		pins = "gpio42";
+		bias-disable;
 		drive-strength = <2>;
 		output-high;
-		bias-disable;
 	};
 
-	en_pp3300_codec: en-pp3300-codec {
-		pins = "gpio67";
-		drive-strength = <2>;
+	en_pp3300_codec: en-pp3300-codec-pins {
+		pins = "gpio105";
+		function = "gpio";
 		bias-disable;
+		drive-strength = <2>;
 	};
 
-	en_pp3300_dx_edp: en-pp3300-dx-edp {
+	en_pp3300_dx_edp: en-pp3300-dx-edp-pins {
 		pins = "gpio80";
 		function = "gpio";
-		drive-strength = <2>;
-		/* Has external pulldown */
 		bias-disable;
+		drive-strength = <2>;
 	};
 
-	en_pp3300_hub: en-pp3300-hub {
-		pins = "gpio24";
+	fp_rst_l: fp-rst-l-pins {
+		pins = "gpio78";
 		function = "gpio";
-		drive-strength = <2>;
-		/* Has external pulldown */
 		bias-disable;
+		drive-strength = <2>;
 	};
 
-	fp_to_ap_irq_l: fp-to-ap-irq-l {
+	fp_to_ap_irq_l: fp-to-ap-irq-l-pins {
 		pins = "gpio61";
 		function = "gpio";
-		input-enable;
 		/* Has external pullup */
 		bias-disable;
 	};
 
-	h1_ap_int_odl: h1-ap-int-odl {
-		pins = "gpio54";
+	fpmcu_boot0: fpmcu-boot0-pins {
+		pins = "gpio68";
 		function = "gpio";
-		input-enable;
-		bias-pull-up;
+		bias-disable;
 	};
 
-	hp_irq: hp-irq {
-		pins = "gpio101";
+	gsc_ap_int_odl: gsc-ap-int-odl-pins {
+		pins = "gpio104";
 		function = "gpio";
 		bias-pull-up;
 	};
 
-	p_sensor_int_l: p-sensor-int-l {
-		pins = "gpio141";
+	hp_irq: hp-irq-pins {
+		pins = "gpio101";
 		function = "gpio";
-		input-enable;
 		bias-pull-up;
 	};
 
-	pen_irq_l: pen-irq-l {
-		pins = "gpio43";
+	hub_en: hub-en-pins {
+		pins = "gpio157";
 		function = "gpio";
-		/* Has external pullup */
 		bias-disable;
+		drive-strength = <2>;
 	};
 
-	pen_pdct_l: pen-pdct-l {
-		pins = "gpio39";
+	pe_wake_odl: pe-wake-odl-pins {
+		pins = "gpio3";
 		function = "gpio";
-		/* Has external pullup */
+		/* Has external pull */
 		bias-disable;
+		drive-strength = <2>;
 	};
 
-	qup_spi8_cs_gpio_init_high: qup-spi8-cs-gpio-init-high {
-		pins = "gpio35";
-		output-high;
-	};
-
-	qup_spi11_cs_gpio_init_high: qup-spi11-cs-gpio-init-high {
-		pins = "gpio47";
-		output-high;
-	};
-
-	qup_spi12_cs_gpio_init_high: qup-spi12-cs-gpio-init-high {
-		pins = "gpio51";
+	/* For ap_spi_fp */
+	qup_spi9_cs_gpio_init_high: qup-spi9-cs-gpio-init-high-pins {
+		pins = "gpio39";
+		function = "gpio";
 		output-high;
 	};
 
-	qup_uart7_sleep_cts: qup-uart7-sleep-cts {
-		pins = "gpio28";
+	/* For ap_ec_spi */
+	qup_spi10_cs_gpio_init_high: qup-spi10-cs-gpio-init-high-pins {
+		pins = "gpio43";
 		function = "gpio";
-		/*
-		 * Configure a pull-down on CTS to match the pull of
-		 * the Bluetooth module.
-		 */
-		bias-pull-down;
+		output-high;
 	};
 
-	qup_uart7_sleep_rts: qup-uart7-sleep-rts {
-		pins = "gpio29";
+	sar0_irq_odl: sar0-irq-odl-pins {
+		pins = "gpio141";
 		function = "gpio";
-		/*
-		 * Configure pull-down on RTS. As RTS is active low
-		 * signal, pull it low to indicate the BT SoC that it
-		 * can wakeup the system anytime from suspend state by
-		 * pulling RX low (by sending wakeup bytes).
-		 */
-		bias-pull-down;
+		bias-pull-up;
 	};
 
-	qup_uart7_sleep_rx: qup-uart7-sleep-rx {
-		pins = "gpio31";
+	sar1_irq_odl: sar1-irq-odl-pins {
+		pins = "gpio140";
 		function = "gpio";
-		/*
-		 * Configure a pull-up on RX. This is needed to avoid
-		 * garbage data when the TX pin of the Bluetooth module
-		 * is floating which may cause spurious wakeups.
-		 */
 		bias-pull-up;
 	};
 
-	qup_uart7_sleep_tx: qup-uart7-sleep-tx {
-		pins = "gpio30";
+	sd_cd_odl: sd-cd-odl-pins {
+		pins = "gpio91";
 		function = "gpio";
-		/*
-		 * Configure pull-up on TX when it isn't actively driven
-		 * to prevent BT SoC from receiving garbage during sleep.
-		 */
 		bias-pull-up;
 	};
 
-	tp_int_odl: tp-int-odl {
-		pins = "gpio102";
+	ssd_en: ssd-en-pins {
+		pins = "gpio51";
 		function = "gpio";
-		/* Has external pullup */
 		bias-disable;
+		drive-strength = <2>;
 	};
 
-	ts_int_l: ts-int-l {
-		pins = "gpio81";
-		function = "gpio";
-		/* Has external pullup */
-		bias-pull-up;
-	};
-
-	ts_reset_l: ts-reset-l {
-		pins = "gpio105";
+	ssd_rst_l: ssd-rst-l-pins {
+		pins = "gpio2";
 		function = "gpio";
-		/* Has external pullup */
 		bias-disable;
 		drive-strength = <2>;
+		output-low;
 	};
 
-	uf_cam_en: uf-cam-en {
-		pins = "gpio6";
+	tp_int_odl: tp-int-odl-pins {
+		pins = "gpio7";
 		function = "gpio";
-		drive-strength = <2>;
-		/* Has external pulldown */
+		/* Has external pullup */
 		bias-disable;
 	};
 
-	wf_cam_en: wf-cam-en {
-		pins = "gpio7";
+	wf_cam_en: wf-cam-en-pins {
+		pins = "gpio119";
 		function = "gpio";
-		drive-strength = <2>;
 		/* Has external pulldown */
 		bias-disable;
+		drive-strength = <2>;
 	};
 };
diff --git a/arch/arm64/boot/dts/qcom/sc7280-idp-ec-h1.dtsi b/arch/arm64/boot/dts/qcom/sc7280-idp-ec-h1.dtsi
new file mode 100644
index 000000000000..7f5143e9bb80
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc7280-idp-ec-h1.dtsi
@@ -0,0 +1,105 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * sc7280 EC/H1 over SPI (common between IDP2 and CRD)
+ *
+ * Copyright (c) 2021 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+ap_ec_spi: &spi10 {
+	status = "okay";
+
+	pinctrl-0 = <&qup_spi10_data_clk>, <&qup_spi10_cs_gpio_init_high>, <&qup_spi10_cs_gpio>;
+	cs-gpios = <&tlmm 43 GPIO_ACTIVE_LOW>;
+
+	cros_ec: ec@0 {
+		compatible = "google,cros-ec-spi";
+		reg = <0>;
+		interrupt-parent = <&tlmm>;
+		interrupts = <18 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&ap_ec_int_l>;
+		spi-max-frequency = <3000000>;
+
+		cros_ec_pwm: pwm {
+			compatible = "google,cros-ec-pwm";
+			#pwm-cells = <1>;
+		};
+
+		i2c_tunnel: i2c-tunnel {
+			compatible = "google,cros-ec-i2c-tunnel";
+			google,remote-bus = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		typec {
+			compatible = "google,cros-ec-typec";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			usb_c0: connector@0 {
+				compatible = "usb-c-connector";
+				reg = <0>;
+				label = "left";
+				power-role = "dual";
+				data-role = "host";
+				try-power-role = "source";
+			};
+
+			usb_c1: connector@1 {
+				compatible = "usb-c-connector";
+				reg = <1>;
+				label = "right";
+				power-role = "dual";
+				data-role = "host";
+				try-power-role = "source";
+			};
+		};
+	};
+};
+
+#include <arm/cros-ec-keyboard.dtsi>
+#include <arm/cros-ec-sbs.dtsi>
+
+ap_h1_spi: &spi14 {
+	status = "okay";
+
+	pinctrl-0 = <&qup_spi14_data_clk>, <&qup_spi14_cs_gpio_init_high>, <&qup_spi14_cs_gpio>;
+	cs-gpios = <&tlmm 59 GPIO_ACTIVE_LOW>;
+
+	cr50: tpm@0 {
+		compatible = "google,cr50";
+		reg = <0>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&h1_ap_int_odl>;
+		spi-max-frequency = <800000>;
+		interrupt-parent = <&tlmm>;
+		interrupts = <104 IRQ_TYPE_EDGE_RISING>;
+	};
+};
+
+&tlmm {
+	ap_ec_int_l: ap-ec-int-l-pins {
+		pins = "gpio18";
+		function = "gpio";
+		input-enable;
+		bias-pull-up;
+	};
+
+	h1_ap_int_odl: h1-ap-int-odl-pins {
+		pins = "gpio104";
+		function = "gpio";
+		input-enable;
+		bias-pull-up;
+	};
+
+	qup_spi10_cs_gpio_init_high: qup-spi10-cs-gpio-init-high-pins {
+		pins = "gpio43";
+		output-high;
+	};
+
+	qup_spi14_cs_gpio_init_high: qup-spi14-cs-gpio-init-high-pins {
+		pins = "gpio59";
+		output-high;
+	};
+};
diff --git a/arch/arm64/boot/dts/qcom/sc7280-idp.dts b/arch/arm64/boot/dts/qcom/sc7280-idp.dts
index 9b991ba5daaf..7559164cdda0 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-idp.dts
+++ b/arch/arm64/boot/dts/qcom/sc7280-idp.dts
@@ -10,6 +10,7 @@
 #include <dt-bindings/iio/qcom,spmi-adc7-pmr735a.h>
 #include "sc7280-idp.dtsi"
 #include "pmr735a.dtsi"
+#include "sc7280-herobrine-lte-sku.dtsi"
 
 / {
 	model = "Qualcomm Technologies, Inc. sc7280 IDP SKU1 platform";
@@ -56,6 +57,10 @@
 	};
 };
 
+&bluetooth {
+	vddio-supply = <&vreg_l19b_1p8>;
+};
+
 &ipa {
 	status = "okay";
 	modem-init;
@@ -74,9 +79,25 @@
 };
 
 &pmk8350_vadc {
-	pmr735a_die_temp {
+	pmr735a-die-temp@403 {
 		reg = <PMR735A_ADC7_DIE_TEMP>;
 		label = "pmr735a_die_temp";
 		qcom,pre-scaling = <1 1>;
 	};
 };
+
+&usb_2 {
+	status = "okay";
+};
+
+&usb_2_dwc3 {
+	dr_mode = "otg";
+};
+
+&usb_2_hsphy {
+	status = "okay";
+
+	vdda-pll-supply = <&vreg_l10c_0p8>;
+	vdda33-supply = <&vreg_l2b_3p0>;
+	vdda18-supply = <&vreg_l1c_1p8>;
+};
diff --git a/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi b/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
index d623d71d8bd4..cd432a2856a7 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280-idp.dtsi
@@ -5,7 +5,6 @@
  * Copyright (c) 2021, The Linux Foundation. All rights reserved.
  */
 
-#include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/iio/qcom,spmi-adc7-pmk8350.h>
 #include <dt-bindings/input/linux-event-codes.h>
 #include "sc7280.dtsi"
@@ -13,7 +12,50 @@
 #include "pm8350c.dtsi"
 #include "pmk8350.dtsi"
 
+#include "sc7280-chrome-common.dtsi"
+
 / {
+	aliases {
+		bluetooth0 = &bluetooth;
+		serial1 = &uart7;
+	};
+
+	max98360a: audio-codec-0 {
+		compatible = "maxim,max98360a";
+		pinctrl-names = "default";
+		pinctrl-0 = <&amp_en>;
+		sdmode-gpios = <&tlmm 63 GPIO_ACTIVE_HIGH>;
+		#sound-dai-cells = <0>;
+	};
+
+	wcd9385: audio-codec-1 {
+		compatible = "qcom,wcd9385-codec";
+		pinctrl-names = "default", "sleep";
+		pinctrl-0 = <&wcd_reset_n>;
+		pinctrl-1 = <&wcd_reset_n_sleep>;
+
+		reset-gpios = <&tlmm 83 GPIO_ACTIVE_HIGH>;
+
+		qcom,rx-device = <&wcd_rx>;
+		qcom,tx-device = <&wcd_tx>;
+
+		vdd-rxtx-supply = <&vreg_l18b_1p8>;
+		vdd-io-supply = <&vreg_l18b_1p8>;
+		vdd-buck-supply = <&vreg_l17b_1p8>;
+		vdd-mic-bias-supply = <&vreg_bob>;
+
+		qcom,micbias1-microvolt = <1800000>;
+		qcom,micbias2-microvolt = <1800000>;
+		qcom,micbias3-microvolt = <1800000>;
+		qcom,micbias4-microvolt = <1800000>;
+
+		qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000 500000
+							  500000 500000 500000>;
+		qcom,mbhc-headset-vthreshold-microvolt = <1700000>;
+		qcom,mbhc-headphone-vthreshold-microvolt = <50000>;
+		#sound-dai-cells = <1>;
+	};
+
 	gpio-keys {
 		compatible = "gpio-keys";
 		label = "gpio-keys";
@@ -21,7 +63,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&key_vol_up_default>;
 
-		volume-up {
+		key-volume-up {
 			label = "volume_up";
 			gpios = <&pm7325_gpios 6 GPIO_ACTIVE_LOW>;
 			linux,input-type = <1>;
@@ -43,56 +85,102 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&nvme_pwren>;
 	};
-};
 
-/*
- * Reserved memory changes
- *
- * Delete all unused memory nodes and define the peripheral memory regions
- * required by the board dts.
- *
- */
+	sound: sound {
+		compatible = "google,sc7280-herobrine";
+		model = "sc7280-wcd938x-max98360a-1mic";
 
-/delete-node/ &hyp_mem;
-/delete-node/ &xbl_mem;
-/delete-node/ &reserved_xbl_uefi_log;
-/delete-node/ &sec_apps_mem;
+		audio-routing =
+			"IN1_HPHL", "HPHL_OUT",
+			"IN2_HPHR", "HPHR_OUT",
+			"AMIC1", "MIC BIAS1",
+			"AMIC2", "MIC BIAS2",
+			"VA DMIC0", "MIC BIAS3",
+			"VA DMIC1", "MIC BIAS3",
+			"VA DMIC2", "MIC BIAS1",
+			"VA DMIC3", "MIC BIAS1",
+			"TX SWR_ADC0", "ADC1_OUTPUT",
+			"TX SWR_ADC1", "ADC2_OUTPUT",
+			"TX SWR_ADC2", "ADC3_OUTPUT",
+			"TX SWR_DMIC0", "DMIC1_OUTPUT",
+			"TX SWR_DMIC1", "DMIC2_OUTPUT",
+			"TX SWR_DMIC2", "DMIC3_OUTPUT",
+			"TX SWR_DMIC3", "DMIC4_OUTPUT",
+			"TX SWR_DMIC4", "DMIC5_OUTPUT",
+			"TX SWR_DMIC5", "DMIC6_OUTPUT",
+			"TX SWR_DMIC6", "DMIC7_OUTPUT",
+			"TX SWR_DMIC7", "DMIC8_OUTPUT";
 
-/* Increase the size from 2.5MB to 8MB */
-&rmtfs_mem {
-	reg = <0x0 0x9c900000 0x0 0x800000>;
-};
+		qcom,msm-mbhc-hphl-swh = <1>;
+		qcom,msm-mbhc-gnd-swh = <1>;
 
-/ {
-	reserved-memory {
-		adsp_mem: memory@86700000 {
-			reg = <0x0 0x86700000 0x0 0x2800000>;
-			no-map;
-		};
+		#address-cells = <1>;
+		#size-cells = <0>;
+		#sound-dai-cells = <0>;
 
-		camera_mem: memory@8ad00000 {
-			reg = <0x0 0x8ad00000 0x0 0x500000>;
-			no-map;
+		dai-link@0 {
+			link-name = "MAX98360A";
+			reg = <0>;
+
+			cpu {
+				sound-dai = <&lpass_cpu MI2S_SECONDARY>;
+			};
+
+			codec {
+				sound-dai = <&max98360a>;
+			};
 		};
 
-		venus_mem: memory@8b200000 {
-			reg = <0x0 0x8b200000 0x0 0x500000>;
-			no-map;
+		dai-link@1 {
+			link-name = "DisplayPort";
+			reg = <1>;
+
+			cpu {
+				sound-dai = <&lpass_cpu LPASS_DP_RX>;
+			};
+
+			codec {
+				sound-dai = <&mdss_dp>;
+			};
 		};
 
-		mpss_mem: memory@8b800000 {
-			reg = <0x0 0x8b800000 0x0 0xf600000>;
-			no-map;
+		dai-link@2 {
+			link-name = "WCD9385 Playback";
+			reg = <2>;
+
+			cpu {
+				sound-dai = <&lpass_cpu LPASS_CDC_DMA_RX0>;
+			};
+
+			codec {
+				sound-dai = <&wcd9385 0>, <&swr0 0>, <&lpass_rx_macro 0>;
+			};
 		};
 
-		wpss_mem: memory@9ae00000 {
-			reg = <0x0 0x9ae00000 0x0 0x1900000>;
-			no-map;
+		dai-link@3 {
+			link-name = "WCD9385 Capture";
+			reg = <3>;
+
+			cpu {
+				sound-dai = <&lpass_cpu LPASS_CDC_DMA_TX3>;
+			};
+
+			codec {
+				sound-dai = <&wcd9385 1>, <&swr1 0>, <&lpass_tx_macro 0>;
+			};
 		};
 
-		mba_mem: memory@9c700000 {
-			reg = <0x0 0x9c700000 0x0 0x200000>;
-			no-map;
+		dai-link@4 {
+			link-name = "DMIC";
+			reg = <4>;
+
+			cpu {
+				sound-dai = <&lpass_cpu LPASS_CDC_DMA_VA_TX0>;
+			};
+
+			codec {
+				sound-dai = <&lpass_va_macro 0>;
+			};
 		};
 	};
 };
@@ -279,14 +367,63 @@
 	};
 };
 
+&gpi_dma0 {
+	status = "okay";
+};
+
+&gpi_dma1 {
+	status = "okay";
+};
+
 &ipa {
 	status = "okay";
 	modem-init;
 };
 
+&lpass_cpu {
+	status = "okay";
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&mi2s1_data0>, <&mi2s1_sclk>, <&mi2s1_ws>;
+
+	dai-link@1 {
+		reg = <MI2S_SECONDARY>;
+		qcom,playback-sd-lines = <0>;
+	};
+
+	dai-link@5 {
+		reg = <LPASS_DP_RX>;
+	};
+
+	dai-link@6 {
+		reg = <LPASS_CDC_DMA_RX0>;
+	};
+
+	dai-link@19 {
+		reg = <LPASS_CDC_DMA_TX3>;
+	};
+
+	dai-link@25 {
+		reg = <LPASS_CDC_DMA_VA_TX0>;
+	};
+};
+
+&lpass_rx_macro {
+	status = "okay";
+};
+
+&lpass_tx_macro {
+	status = "okay";
+};
+
+&lpass_va_macro {
+	status = "okay";
+	vdd-micb-supply = <&vreg_bob>;
+};
+
 &pcie1 {
 	status = "okay";
-	perst-gpio = <&tlmm 2 GPIO_ACTIVE_LOW>;
+	perst-gpios = <&tlmm 2 GPIO_ACTIVE_LOW>;
 
 	vddpe-3v3-supply = <&nvme_3v3_regulator>;
 
@@ -302,7 +439,7 @@
 };
 
 &pmk8350_vadc {
-	pmk8350_die_temp {
+	pmk8350-die-temp@3 {
 		reg = <PMK8350_ADC7_DIE_TEMP>;
 		label = "pmk8350_die_temp";
 		qcom,pre-scaling = <1 1>;
@@ -313,20 +450,6 @@
 	vcc-supply = <&vreg_l1c_1p8>;
 };
 
-&qspi {
-	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&qspi_clk>, <&qspi_cs0>, <&qspi_data01>;
-
-	flash@0 {
-		compatible = "jedec,spi-nor";
-		reg = <0>;
-		spi-max-frequency = <37500000>;
-		spi-tx-bus-width = <2>;
-		spi-rx-bus-width = <2>;
-	};
-};
-
 &qupv3_id_0 {
 	status = "okay";
 };
@@ -335,20 +458,9 @@
 	status = "okay";
 };
 
-&remoteproc_mpss {
-	status = "okay";
-	compatible = "qcom,sc7280-mss-pil";
-	iommus = <&apps_smmu 0x124 0x0>, <&apps_smmu 0x488 0x7>;
-	memory-region = <&mba_mem &mpss_mem>;
-};
-
 &sdhc_1 {
 	status = "okay";
 
-	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&sdc1_on>;
-	pinctrl-1 = <&sdc1_off>;
-
 	non-removable;
 	no-sd;
 	no-sdio;
@@ -360,9 +472,8 @@
 &sdhc_2 {
 	status = "okay";
 
-	pinctrl-names = "default", "sleep";
-	pinctrl-0 = <&sdc2_on>;
-	pinctrl-1 = <&sdc2_off>;
+	pinctrl-0 = <&sdc2_clk>, <&sdc2_cmd>, <&sdc2_data>, <&sd_cd>;
+	pinctrl-1 = <&sdc2_clk_sleep>, <&sdc2_cmd_sleep>, <&sdc2_data_sleep>, <&sd_cd>;
 
 	vmmc-supply = <&vreg_l9c_2p9>;
 	vqmmc-supply = <&vreg_l6c_2p9>;
@@ -370,6 +481,28 @@
 	cd-gpios = <&tlmm 91 GPIO_ACTIVE_LOW>;
 };
 
+&swr0 {
+	status = "okay";
+
+	wcd_rx: codec@0,4 {
+		compatible = "sdw20217010d00";
+		reg = <0 4>;
+		#sound-dai-cells = <1>;
+		qcom,rx-port-mapping = <1 2 3 4 5>;
+	};
+};
+
+&swr1 {
+	status = "okay";
+
+	wcd_tx: codec@0,3 {
+		compatible = "sdw20217010d00";
+		reg = <0 3>;
+		#sound-dai-cells = <1>;
+		qcom,tx-port-mapping = <1 2 3 4>;
+	};
+};
+
 &uart5 {
 	compatible = "qcom,geni-debug-uart";
 	status = "okay";
@@ -398,22 +531,6 @@
 	vdda-pll-supply = <&vreg_l1b_0p8>;
 };
 
-&usb_2 {
-	status = "okay";
-};
-
-&usb_2_dwc3 {
-	dr_mode = "peripheral";
-};
-
-&usb_2_hsphy {
-	status = "okay";
-
-	vdda-pll-supply = <&vreg_l10c_0p8>;
-	vdda33-supply = <&vreg_l2b_3p0>;
-	vdda18-supply = <&vreg_l1c_1p8>;
-};
-
 &uart7 {
 	status = "okay";
 
@@ -422,12 +539,109 @@
 				<&tlmm 31 IRQ_TYPE_EDGE_FALLING>;
 	pinctrl-names = "default", "sleep";
 	pinctrl-1 = <&qup_uart7_sleep_cts>, <&qup_uart7_sleep_rts>, <&qup_uart7_sleep_tx>, <&qup_uart7_sleep_rx>;
+
+	bluetooth: bluetooth {
+		compatible = "qcom,wcn6750-bt";
+		pinctrl-names = "default";
+		pinctrl-0 = <&bt_en>, <&sw_ctrl>;
+		enable-gpios = <&tlmm 85 GPIO_ACTIVE_HIGH>;
+		swctrl-gpios = <&tlmm 86 GPIO_ACTIVE_HIGH>;
+		vddaon-supply = <&vreg_s7b_0p9>;
+		vddbtcxmx-supply = <&vreg_s7b_0p9>;
+		vddrfacmn-supply = <&vreg_s7b_0p9>;
+		vddrfa0p8-supply = <&vreg_s7b_0p9>;
+		vddrfa1p7-supply = <&vreg_s1b_1p8>;
+		vddrfa1p2-supply = <&vreg_s8b_1p2>;
+		vddrfa2p2-supply = <&vreg_s1c_2p2>;
+		vddasd-supply = <&vreg_l11c_2p8>;
+		max-speed = <3200000>;
+	};
 };
 
 /* PINCTRL - additions to nodes defined in sc7280.dtsi */
 
+&dp_hot_plug_det {
+	bias-disable;
+};
+
+&lpass_dmic01_clk {
+	drive-strength = <8>;
+	bias-disable;
+};
+
+&lpass_dmic01_clk_sleep {
+	drive-strength = <2>;
+};
+
+&lpass_dmic01_data {
+	bias-pull-down;
+};
+
+&lpass_dmic23_clk {
+	drive-strength = <8>;
+	bias-disable;
+};
+
+&lpass_dmic23_clk_sleep {
+	drive-strength = <2>;
+};
+
+&lpass_dmic23_data {
+	bias-pull-down;
+};
+
+&lpass_rx_swr_clk {
+	drive-strength = <2>;
+	slew-rate = <1>;
+	bias-disable;
+};
+
+&lpass_rx_swr_clk_sleep {
+	bias-pull-down;
+};
+
+&lpass_rx_swr_data {
+	drive-strength = <2>;
+	slew-rate = <1>;
+	bias-bus-hold;
+};
+
+&lpass_rx_swr_data_sleep {
+	bias-pull-down;
+};
+
+&lpass_tx_swr_clk {
+	drive-strength = <2>;
+	slew-rate = <1>;
+	bias-disable;
+};
+
+&lpass_tx_swr_clk_sleep {
+	bias-pull-down;
+};
+
+&lpass_tx_swr_data {
+	drive-strength = <2>;
+	slew-rate = <1>;
+	bias-bus-hold;
+};
+
+&mi2s1_data0 {
+	drive-strength = <6>;
+	bias-disable;
+};
+
+&mi2s1_sclk {
+	drive-strength = <6>;
+	bias-disable;
+};
+
+&mi2s1_ws {
+	drive-strength = <6>;
+};
+
 &pm7325_gpios {
-	key_vol_up_default: key-vol-up-default {
+	key_vol_up_default: key-vol-up-state {
 		pins = "gpio6";
 		function = "normal";
 		input-enable;
@@ -437,6 +651,11 @@
 	};
 };
 
+&pcie1_clkreq_n {
+	bias-pull-up;
+	drive-strength = <2>;
+};
+
 &qspi_cs0 {
 	bias-disable;
 };
@@ -462,10 +681,13 @@
 
 &qup_uart7_cts {
 	/*
-	 * Configure a pull-down on CTS to match the pull of
-	 * the Bluetooth module.
+	 * Configure a bias-bus-hold on CTS to lower power
+	 * usage when Bluetooth is turned off. Bus hold will
+	 * maintain a low power state regardless of whether
+	 * the Bluetooth module drives the pin in either
+	 * direction or leaves the pin fully unpowered.
 	 */
-	bias-pull-down;
+	bias-bus-hold;
 };
 
 &qup_uart7_rts {
@@ -490,12 +712,59 @@
 	bias-pull-up;
 };
 
+&sdc1_clk {
+	bias-disable;
+	drive-strength = <16>;
+};
+
+&sdc1_cmd {
+	bias-pull-up;
+	drive-strength = <10>;
+};
+
+&sdc1_data {
+	bias-pull-up;
+	drive-strength = <10>;
+};
+
+&sdc1_rclk {
+	bias-pull-down;
+};
+
+&sdc2_clk {
+	bias-disable;
+	drive-strength = <16>;
+};
+
+&sdc2_cmd {
+	bias-pull-up;
+	drive-strength = <10>;
+};
+
+&sdc2_data {
+	bias-pull-up;
+	drive-strength = <10>;
+};
+
 &tlmm {
-	nvme_pwren: nvme-pwren {
+	amp_en: amp-en {
+		pins = "gpio63";
+		bias-pull-down;
+		drive-strength = <2>;
+	};
+
+	bt_en: bt-en-pins {
+		pins = "gpio85";
+		function = "gpio";
+		output-low;
+		bias-disable;
+	};
+
+	nvme_pwren: nvme-pwren-pins {
 		function = "gpio";
 	};
 
-	pcie1_reset_n: pcie1-reset-n {
+	pcie1_reset_n: pcie1-reset-n-pins {
 		pins = "gpio2";
 		function = "gpio";
 
@@ -504,7 +773,7 @@
 		bias-disable;
 	};
 
-	pcie1_wake_n: pcie1-wake-n {
+	pcie1_wake_n: pcie1-wake-n-pins {
 		pins = "gpio3";
 		function = "gpio";
 
@@ -512,17 +781,20 @@
 		bias-pull-up;
 	};
 
-	qup_uart7_sleep_cts: qup-uart7-sleep-cts {
+	qup_uart7_sleep_cts: qup-uart7-sleep-cts-pins {
 		pins = "gpio28";
 		function = "gpio";
 		/*
-		 * Configure a pull-down on CTS to match the pull of
-		 * the Bluetooth module.
+		 * Configure a bias-bus-hold on CTS to lower power
+		 * usage when Bluetooth is turned off. Bus hold will
+		 * maintain a low power state regardless of whether
+		 * the Bluetooth module drives the pin in either
+		 * direction or leaves the pin fully unpowered.
 		 */
-		bias-pull-down;
+		bias-bus-hold;
 	};
 
-	qup_uart7_sleep_rts: qup-uart7-sleep-rts {
+	qup_uart7_sleep_rts: qup-uart7-sleep-rts-pins {
 		pins = "gpio29";
 		function = "gpio";
 		/*
@@ -534,7 +806,7 @@
 		bias-pull-down;
 	};
 
-	qup_uart7_sleep_tx: qup-uart7-sleep-tx {
+	qup_uart7_sleep_tx: qup-uart7-sleep-tx-pins {
 		pins = "gpio30";
 		function = "gpio";
 		/*
@@ -544,7 +816,7 @@
 		bias-pull-up;
 	};
 
-	qup_uart7_sleep_rx: qup-uart7-sleep-rx {
+	qup_uart7_sleep_rx: qup-uart7-sleep-rx-pins {
 		pins = "gpio31";
 		function = "gpio";
 		/*
@@ -554,47 +826,29 @@
 		 */
 		bias-pull-up;
 	};
-};
 
-&sdc1_on {
-	clk {
-		bias-disable;
-		drive-strength = <16>;
-	};
-
-	cmd {
-		bias-pull-up;
-		drive-strength = <10>;
-	};
-
-	data {
+	sd_cd: sd-cd-pins {
+		pins = "gpio91";
+		function = "gpio";
 		bias-pull-up;
-		drive-strength = <10>;
 	};
 
-	rclk {
+	sw_ctrl: sw-ctrl-pins {
+		pins = "gpio86";
+		function = "gpio";
 		bias-pull-down;
 	};
-};
-
-&sdc2_on {
-	clk {
-		bias-disable;
-		drive-strength = <16>;
-	};
-
-	cmd {
-		bias-pull-up;
-		drive-strength = <10>;
-	};
 
-	data {
-		bias-pull-up;
-		drive-strength = <10>;
+	wcd_reset_n: wcd-reset-n {
+		pins = "gpio83";
+		function = "gpio";
+		drive-strength = <8>;
 	};
 
-	sd-cd {
-		pins = "gpio91";
-		bias-pull-up;
+	wcd_reset_n_sleep: wcd-reset-n-sleep {
+		pins = "gpio83";
+		function = "gpio";
+		drive-strength = <8>;
+		bias-disable;
 	};
 };
diff --git a/arch/arm64/boot/dts/qcom/sc7280-idp2.dts b/arch/arm64/boot/dts/qcom/sc7280-idp2.dts
index 3ae99697d893..d4f7cab17078 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-idp2.dts
+++ b/arch/arm64/boot/dts/qcom/sc7280-idp2.dts
@@ -8,6 +8,7 @@
 /dts-v1/;
 
 #include "sc7280-idp.dtsi"
+#include "sc7280-idp-ec-h1.dtsi"
 
 / {
 	model = "Qualcomm Technologies, Inc. sc7280 IDP SKU2 platform";
@@ -22,6 +23,10 @@
 	};
 };
 
+&bluetooth {
+	vddio-supply = <&vreg_l18b_1p8>;
+};
+
 &nvme_pwren {
 	pins = "gpio51";
 };
@@ -29,3 +34,7 @@
 &nvme_3v3_regulator {
 	gpio = <&tlmm 51 GPIO_ACTIVE_HIGH>;
 };
+
+&pm8350c_pwm {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/qcom/sc7280-qcard.dtsi b/arch/arm64/boot/dts/qcom/sc7280-qcard.dtsi
new file mode 100644
index 000000000000..4b8c676b0bb1
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc7280-qcard.dtsi
@@ -0,0 +1,686 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * sc7280 Qcard device tree source
+ *
+ * Qcard PCB has the processor, RAM, eMMC (if stuffed), and eDP connector (if
+ * stuffed) on it. This device tree tries to encapsulate all the things that
+ * all boards using Qcard will have in common. Given that there are stuffing
+ * options, some things may be left with status "disabled" and enabled in
+ * the actual board device tree files.
+ *
+ * Copyright 2022 Google LLC.
+ */
+
+#include <dt-bindings/iio/qcom,spmi-adc7-pmk8350.h>
+#include <dt-bindings/iio/qcom,spmi-adc7-pmr735a.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+
+#include "sc7280.dtsi"
+
+/* PMICs depend on spmi_bus label and so must come after SoC */
+#include "pm7325.dtsi"
+#include "pm8350c.dtsi"
+#include "pmk8350.dtsi"
+
+/ {
+	aliases {
+		bluetooth0 = &bluetooth;
+		serial0 = &uart5;
+		serial1 = &uart7;
+		wifi0 = &wifi;
+	};
+
+	wcd9385: audio-codec-1 {
+		compatible = "qcom,wcd9385-codec";
+		pinctrl-names = "default", "sleep";
+		pinctrl-0 = <&wcd_reset_n>, <&us_euro_hs_sel>;
+		pinctrl-1 = <&wcd_reset_n_sleep>, <&us_euro_hs_sel>;
+
+		reset-gpios = <&tlmm 83 GPIO_ACTIVE_HIGH>;
+		us-euro-gpios = <&tlmm 81 GPIO_ACTIVE_HIGH>;
+
+		qcom,rx-device = <&wcd_rx>;
+		qcom,tx-device = <&wcd_tx>;
+
+		vdd-rxtx-supply = <&vreg_l18b_1p8>;
+		vdd-io-supply = <&vreg_l18b_1p8>;
+		vdd-buck-supply = <&vreg_l17b_1p8>;
+		vdd-mic-bias-supply = <&vreg_bob>;
+
+		qcom,micbias1-microvolt = <1800000>;
+		qcom,micbias2-microvolt = <1800000>;
+		qcom,micbias3-microvolt = <1800000>;
+		qcom,micbias4-microvolt = <1800000>;
+
+		qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000 500000
+							  500000 500000 500000>;
+		qcom,mbhc-headset-vthreshold-microvolt = <1700000>;
+		qcom,mbhc-headphone-vthreshold-microvolt = <50000>;
+		#sound-dai-cells = <1>;
+
+		status = "disabled";
+	};
+
+	pm8350c_pwm_backlight: backlight {
+		compatible = "pwm-backlight";
+		status = "disabled";
+
+		enable-gpios = <&pm8350c_gpios 7 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_edp_bl_en>;
+		pwms = <&pm8350c_pwm 3 65535>;
+	};
+};
+
+&apps_rsc {
+	/*
+	 * Regulators are given labels corresponding to the various names
+	 * they are referred to on schematics. They are also given labels
+	 * corresponding to named voltage inputs on the SoC or components
+	 * bundled with the SoC (like radio companion chips). We totally
+	 * ignore it when one regulator is the input to another regulator.
+	 * That's handled automatically by the initial config given to
+	 * RPMH by the firmware.
+	 *
+	 * Regulators that the HLOS (High Level OS) doesn't touch at all
+	 * are left out of here since they are managed elsewhere.
+	 */
+
+	pm7325-regulators {
+		compatible = "qcom,pm7325-rpmh-regulators";
+		qcom,pmic-id = "b";
+
+		vdd19_pmu_pcie_i:
+		vdd19_pmu_rfa_i:
+		vreg_s1b_1p856: smps1 {
+			regulator-min-microvolt = <1856000>;
+			regulator-max-microvolt = <2040000>;
+		};
+
+		vdd_pmu_aon_i:
+		vdd09_pmu_rfa_i:
+		vdd095_mx_pmu:
+		vdd095_pmu:
+		vreg_s7b_0p952: smps7 {
+			regulator-min-microvolt = <535000>;
+			regulator-max-microvolt = <1120000>;
+		};
+
+		vdd13_pmu_rfa_i:
+		vdd13_pmu_pcie_i:
+		vreg_s8b_1p256: smps8 {
+			regulator-min-microvolt = <1256000>;
+			regulator-max-microvolt = <1500000>;
+		};
+
+		vdd_a_usbssdp_0_core:
+		vreg_l1b_0p912: ldo1 {
+			regulator-min-microvolt = <825000>;
+			regulator-max-microvolt = <925000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vdd_a_usbhs_3p1:
+		vreg_l2b_3p072: ldo2 {
+			regulator-min-microvolt = <2700000>;
+			regulator-max-microvolt = <3544000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vdd_a_csi_0_1_1p2:
+		vdd_a_csi_2_3_1p2:
+		vdd_a_csi_4_1p2:
+		vdd_a_dsi_0_1p2:
+		vdd_a_edp_0_1p2:
+		vdd_a_qlink_0_1p2:
+		vdd_a_qlink_1_1p2:
+		vdd_a_pcie_0_1p2:
+		vdd_a_pcie_1_1p2:
+		vdd_a_ufs_0_1p2:
+		vdd_a_usbssdp_0_1p2:
+		vreg_l6b_1p2: ldo6 {
+			regulator-min-microvolt = <1140000>;
+			regulator-max-microvolt = <1260000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		/*
+		 * Despite the fact that this is named to be 2.5V on the
+		 * schematic, it powers eMMC which doesn't accept 2.5V
+		 */
+		vreg_l7b_2p5: ldo7 {
+			regulator-min-microvolt = <2960000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l17b_1p8: ldo17 {
+			regulator-min-microvolt = <1700000>;
+			regulator-max-microvolt = <1900000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vdd_px_wcd9385:
+		vdd_txrx:
+		vddpx_0:
+		vddpx_3:
+		vddpx_7:
+		vreg_l18b_1p8: ldo18 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2000000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vdd_1p8:
+		vdd_px_sdr735:
+		vdd_pxm:
+		vdd18_io:
+		vddio_px_1:
+		vddio_px_2:
+		vddio_px_3:
+		vddpx_ts:
+		vddpx_wl4otp:
+		vreg_l19b_1p8: ldo19 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	pm8350c-regulators {
+		compatible = "qcom,pm8350c-rpmh-regulators";
+		qcom,pmic-id = "c";
+
+		vdd22_wlbtpa_ch0:
+		vdd22_wlbtpa_ch1:
+		vdd22_wlbtppa_ch0:
+		vdd22_wlbtppa_ch1:
+		vdd22_wlpa5g_ch0:
+		vdd22_wlpa5g_ch1:
+		vdd22_wlppa5g_ch0:
+		vdd22_wlppa5g_ch1:
+		vreg_s1c_2p2: smps1 {
+			regulator-min-microvolt = <2190000>;
+			regulator-max-microvolt = <2210000>;
+		};
+
+		lp4_vdd2_1p052:
+		vreg_s9c_0p676: smps9 {
+			regulator-min-microvolt = <1010000>;
+			regulator-max-microvolt = <1170000>;
+		};
+
+		vdda_apc_cs_1p8:
+		vdda_gfx_cs_1p8:
+		vdda_turing_q6_cs_1p8:
+		vdd_a_cxo_1p8:
+		vdd_a_qrefs_1p8:
+		vdd_a_usbhs_1p8:
+		vdd_qfprom:
+		vreg_l1c_1p8: ldo1 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1980000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2c_1p8: ldo2 {
+			regulator-min-microvolt = <1620000>;
+			regulator-max-microvolt = <1980000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3c_3p0: ldo3 {
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <3540000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vddpx_5:
+		vreg_l4c_1p8_3p0: ldo4 {
+			regulator-min-microvolt = <1620000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vddpx_6:
+		vreg_l5c_1p8_3p0: ldo5 {
+			regulator-min-microvolt = <1620000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vddpx_2:
+		vreg_l6c_2p96: ldo6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l7c_3p0: ldo7 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3544000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l8c_1p8: ldo8 {
+			regulator-min-microvolt = <1620000>;
+			regulator-max-microvolt = <2000000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l9c_2p96: ldo9 {
+			regulator-min-microvolt = <2960000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vdd_a_csi_0_1_0p9:
+		vdd_a_csi_2_3_0p9:
+		vdd_a_csi_4_0p9:
+		vdd_a_dsi_0_0p9:
+		vdd_a_dsi_0_pll_0p9:
+		vdd_a_edp_0_0p9:
+		vdd_a_gnss_0p9:
+		vdd_a_pcie_0_core:
+		vdd_a_pcie_1_core:
+		vdd_a_qlink_0_0p9:
+		vdd_a_qlink_0_0p9_ck:
+		vdd_a_qlink_1_0p9:
+		vdd_a_qlink_1_0p9_ck:
+		vdd_a_qrefs_0p875_0:
+		vdd_a_qrefs_0p875_1:
+		vdd_a_qrefs_0p875_2:
+		vdd_a_qrefs_0p875_3:
+		vdd_a_qrefs_0p875_4_5:
+		vdd_a_qrefs_0p875_6:
+		vdd_a_qrefs_0p875_7:
+		vdd_a_qrefs_0p875_8:
+		vdd_a_qrefs_0p875_9:
+		vdd_a_ufs_0_core:
+		vdd_a_usbhs_core:
+		vreg_l10c_0p88: ldo10 {
+			regulator-min-microvolt = <720000>;
+			regulator-max-microvolt = <1050000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l11c_2p8: ldo11 {
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <3544000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l12c_1p8: ldo12 {
+			regulator-min-microvolt = <1650000>;
+			regulator-max-microvolt = <2000000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l13c_3p0: ldo13 {
+			regulator-min-microvolt = <2700000>;
+			regulator-max-microvolt = <3544000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vdd_flash:
+		vdd_iris_rgb:
+		vdd_mic_bias:
+		vreg_bob: bob {
+			regulator-min-microvolt = <3008000>;
+			regulator-max-microvolt = <3960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>;
+		};
+	};
+};
+
+/* ADDITIONS TO NODES DEFINED IN PARENT DEVICE TREE FILES */
+
+&ipa {
+	status = "okay";
+	modem-init;
+};
+
+&lpass_va_macro {
+	vdd-micb-supply = <&vreg_bob>;
+};
+
+/* NOTE: Not all Qcards have eDP connector stuffed */
+&mdss_edp {
+	aux-bus {
+		edp_panel: panel {
+			compatible = "edp-panel";
+
+			backlight = <&pm8350c_pwm_backlight>;
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				port@0 {
+					reg = <0>;
+					edp_panel_in: endpoint {
+						remote-endpoint = <&mdss_edp_out>;
+					};
+				};
+			};
+		};
+	};
+};
+
+&mdss_edp_out {
+	remote-endpoint = <&edp_panel_in>;
+};
+
+&mdss_edp_phy {
+	vdda-pll-supply = <&vdd_a_edp_0_0p9>;
+	vdda-phy-supply = <&vdd_a_edp_0_1p2>;
+};
+
+&pcie1_phy {
+	vdda-phy-supply = <&vreg_l10c_0p88>;
+	vdda-pll-supply = <&vreg_l6b_1p2>;
+};
+
+&pm8350c_pwm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pmic_edp_bl_pwm>;
+};
+
+&pmk8350_vadc {
+	pmk8350-die-temp@3 {
+		reg = <PMK8350_ADC7_DIE_TEMP>;
+		label = "pmk8350_die_temp";
+		qcom,pre-scaling = <1 1>;
+	};
+
+	pmr735a-die-temp@403 {
+		reg = <PMR735A_ADC7_DIE_TEMP>;
+		label = "pmr735a_die_temp";
+		qcom,pre-scaling = <1 1>;
+	};
+};
+
+&qfprom {
+	vcc-supply = <&vdd_qfprom>;
+};
+
+/* For eMMC. NOTE: not all Qcards have eMMC stuffed */
+&sdhc_1 {
+	vmmc-supply = <&vreg_l7b_2p5>;
+	vqmmc-supply = <&vreg_l19b_1p8>;
+
+	non-removable;
+	no-sd;
+	no-sdio;
+};
+
+&swr0 {
+	wcd_rx: codec@0,4 {
+		compatible = "sdw20217010d00";
+		reg = <0 4>;
+		#sound-dai-cells = <1>;
+		qcom,rx-port-mapping = <1 2 3 4 5>;
+	};
+};
+
+&swr1 {
+	wcd_tx: codec@0,3 {
+		compatible = "sdw20217010d00";
+		reg = <0 3>;
+		#sound-dai-cells = <1>;
+		qcom,tx-port-mapping = <1 2 3 4>;
+	};
+};
+
+uart_dbg: &uart5 {
+	compatible = "qcom,geni-debug-uart";
+	status = "okay";
+};
+
+mos_bt_uart: &uart7 {
+	status = "okay";
+
+	/delete-property/ interrupts;
+	interrupts-extended = <&intc GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>,
+				<&tlmm 31 IRQ_TYPE_EDGE_FALLING>;
+	pinctrl-names = "default", "sleep";
+	pinctrl-1 = <&qup_uart7_sleep_cts>, <&qup_uart7_sleep_rts>, <&qup_uart7_sleep_tx>, <&qup_uart7_sleep_rx>;
+
+	bluetooth: bluetooth {
+		compatible = "qcom,wcn6750-bt";
+		pinctrl-names = "default";
+		pinctrl-0 = <&mos_bt_en>;
+		enable-gpios = <&tlmm 85 GPIO_ACTIVE_HIGH>;
+		swctrl-gpios = <&tlmm 86 GPIO_ACTIVE_HIGH>;
+		vddaon-supply = <&vreg_s7b_0p952>;
+		vddbtcxmx-supply = <&vreg_s7b_0p952>;
+		vddrfacmn-supply = <&vreg_s7b_0p952>;
+		vddrfa0p8-supply = <&vreg_s7b_0p952>;
+		vddrfa1p7-supply = <&vdd19_pmu_rfa_i>;
+		vddrfa1p2-supply = <&vdd13_pmu_rfa_i>;
+		vddrfa2p2-supply = <&vreg_s1c_2p2>;
+		vddasd-supply = <&vreg_l11c_2p8>;
+		vddio-supply = <&vreg_l18b_1p8>;
+		max-speed = <3200000>;
+	};
+};
+
+&usb_1_hsphy {
+	vdda-pll-supply = <&vdd_a_usbhs_core>;
+	vdda33-supply = <&vdd_a_usbhs_3p1>;
+	vdda18-supply = <&vdd_a_usbhs_1p8>;
+};
+
+&usb_1_qmpphy {
+	vdda-phy-supply = <&vdd_a_usbssdp_0_1p2>;
+	vdda-pll-supply = <&vdd_a_usbssdp_0_core>;
+};
+
+&usb_2_hsphy {
+	vdda-pll-supply = <&vdd_a_usbhs_core>;
+	vdda33-supply = <&vdd_a_usbhs_3p1>;
+	vdda18-supply = <&vdd_a_usbhs_1p8>;
+};
+
+/*
+ * PINCTRL - ADDITIONS TO NODES IN PARENT DEVICE TREE FILES
+ *
+ * NOTE: In general if pins leave the Qcard then the pinctrl goes in the
+ * baseboard or board device tree, not here.
+ */
+
+/* No external pull for eDP HPD, so set the internal one. */
+&edp_hot_plug_det {
+	bias-pull-down;
+};
+
+/*
+ * For ts_i2c
+ *
+ * Technically this i2c bus actually leaves the Qcard, but it leaves directly
+ * via the eDP connector (it doesn't hit the baseboard). The external pulls
+ * are on Qcard.
+ */
+&qup_i2c13_data_clk {
+	/* Has external pull */
+	bias-disable;
+	drive-strength = <2>;
+};
+
+/* For mos_bt_uart */
+&qup_uart7_cts {
+	/*
+	 * Configure a bias-bus-hold on CTS to lower power
+	 * usage when Bluetooth is turned off. Bus hold will
+	 * maintain a low power state regardless of whether
+	 * the Bluetooth module drives the pin in either
+	 * direction or leaves the pin fully unpowered.
+	 */
+	bias-bus-hold;
+};
+
+/* For mos_bt_uart */
+&qup_uart7_rts {
+	/* We'll drive RTS, so no pull */
+	bias-disable;
+	drive-strength = <2>;
+};
+
+/* For mos_bt_uart */
+&qup_uart7_tx {
+	/* We'll drive TX, so no pull */
+	bias-disable;
+	drive-strength = <2>;
+};
+
+/* For mos_bt_uart */
+&qup_uart7_rx {
+	/*
+	 * Configure a pull-up on RX. This is needed to avoid
+	 * garbage data when the TX pin of the Bluetooth module is
+	 * in tri-state (module powered off or not driving the
+	 * signal yet).
+	 */
+	bias-pull-up;
+};
+
+/* eMMC, if stuffed, is straight on the Qcard */
+&sdc1_clk {
+	bias-disable;
+	drive-strength = <16>;
+};
+
+&sdc1_cmd {
+	bias-pull-up;
+	drive-strength = <10>;
+};
+
+&sdc1_data {
+	bias-pull-up;
+	drive-strength = <10>;
+};
+
+&sdc1_rclk {
+	bias-pull-down;
+};
+
+/*
+ * PINCTRL - QCARD
+ *
+ * This has entries that are defined by Qcard even if they go to the main
+ * board. In cases where the pulls may be board dependent we defer those
+ * settings to the board device tree. Drive strengths tend to be assinged here
+ * but could conceivably be overwridden by board device trees.
+ */
+
+&pm8350c_gpios {
+	pmic_edp_bl_en: pmic-edp-bl-en-state {
+		pins = "gpio7";
+		function = "normal";
+		bias-disable;
+		qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
+
+		/* Force backlight to be disabled to match state at boot. */
+		output-low;
+	};
+
+	pmic_edp_bl_pwm: pmic-edp-bl-pwm-state {
+		pins = "gpio8";
+		function = "func1";
+		bias-disable;
+		qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
+		output-low;
+		power-source = <0>;
+	};
+};
+
+&tlmm {
+	mos_bt_en: mos-bt-en-pins {
+		pins = "gpio85";
+		function = "gpio";
+		drive-strength = <2>;
+		output-low;
+	};
+
+	/* For mos_bt_uart */
+	qup_uart7_sleep_cts: qup-uart7-sleep-cts-pins {
+		pins = "gpio28";
+		function = "gpio";
+		/*
+		 * Configure a bias-bus-hold on CTS to lower power
+		 * usage when Bluetooth is turned off. Bus hold will
+		 * maintain a low power state regardless of whether
+		 * the Bluetooth module drives the pin in either
+		 * direction or leaves the pin fully unpowered.
+		 */
+		bias-bus-hold;
+	};
+
+	/* For mos_bt_uart */
+	qup_uart7_sleep_rts: qup-uart7-sleep-rts-pins {
+		pins = "gpio29";
+		function = "gpio";
+		/*
+		 * Configure pull-down on RTS. As RTS is active low
+		 * signal, pull it low to indicate the BT SoC that it
+		 * can wakeup the system anytime from suspend state by
+		 * pulling RX low (by sending wakeup bytes).
+		 */
+		bias-pull-down;
+	};
+
+	/* For mos_bt_uart */
+	qup_uart7_sleep_rx: qup-uart7-sleep-rx-pins {
+		pins = "gpio31";
+		function = "gpio";
+		/*
+		 * Configure a pull-up on RX. This is needed to avoid
+		 * garbage data when the TX pin of the Bluetooth module
+		 * is floating which may cause spurious wakeups.
+		 */
+		bias-pull-up;
+	};
+
+	/* For mos_bt_uart */
+	qup_uart7_sleep_tx: qup-uart7-sleep-tx-pins {
+		pins = "gpio30";
+		function = "gpio";
+		/*
+		 * Configure pull-up on TX when it isn't actively driven
+		 * to prevent BT SoC from receiving garbage during sleep.
+		 */
+		bias-pull-up;
+	};
+
+	ts_int_conn: ts-int-conn-pins {
+		pins = "gpio55";
+		function = "gpio";
+		bias-pull-up;
+	};
+
+	ts_rst_conn: ts-rst-conn-pins {
+		pins = "gpio54";
+		function = "gpio";
+		drive-strength = <2>;
+	};
+
+	us_euro_hs_sel: us-euro-hs-sel {
+		pins = "gpio81";
+		function = "gpio";
+		bias-pull-down;
+		drive-strength = <2>;
+	};
+
+	wcd_reset_n: wcd-reset-n {
+		pins = "gpio83";
+		function = "gpio";
+		drive-strength = <8>;
+	};
+
+	wcd_reset_n_sleep: wcd-reset-n-sleep {
+		pins = "gpio83";
+		function = "gpio";
+		drive-strength = <8>;
+		bias-disable;
+	};
+};
diff --git a/arch/arm64/boot/dts/qcom/sc7280.dtsi b/arch/arm64/boot/dts/qcom/sc7280.dtsi
index 365a2e04e285..212580316d3e 100644
--- a/arch/arm64/boot/dts/qcom/sc7280.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280.dtsi
@@ -4,12 +4,17 @@
  *
  * Copyright (c) 2020-2021, The Linux Foundation. All rights reserved.
  */
-
+#include <dt-bindings/clock/qcom,camcc-sc7280.h>
 #include <dt-bindings/clock/qcom,dispcc-sc7280.h>
 #include <dt-bindings/clock/qcom,gcc-sc7280.h>
 #include <dt-bindings/clock/qcom,gpucc-sc7280.h>
+#include <dt-bindings/clock/qcom,lpassaudiocc-sc7280.h>
+#include <dt-bindings/clock/qcom,lpasscorecc-sc7280.h>
 #include <dt-bindings/clock/qcom,rpmh.h>
 #include <dt-bindings/clock/qcom,videocc-sc7280.h>
+#include <dt-bindings/dma/qcom-gpi.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interconnect/qcom,osm-l3.h>
 #include <dt-bindings/interconnect/qcom,sc7280.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/mailbox/qcom-ipcc.h>
@@ -17,6 +22,7 @@
 #include <dt-bindings/reset/qcom,sdm845-aoss.h>
 #include <dt-bindings/reset/qcom,sdm845-pdc.h>
 #include <dt-bindings/soc/qcom,rpmh-rsc.h>
+#include <dt-bindings/sound/qcom,lpass.h>
 #include <dt-bindings/thermal/thermal.h>
 
 / {
@@ -83,6 +89,11 @@
 		#size-cells = <2>;
 		ranges;
 
+		wlan_ce_mem: memory@4cd000 {
+			no-map;
+			reg = <0x0 0x004cd000 0x0 0x1000>;
+		};
+
 		hyp_mem: memory@80000000 {
 			reg = <0x0 0x80000000 0x0 0x600000>;
 			no-map;
@@ -129,6 +140,11 @@
 			no-map;
 		};
 
+		video_mem: memory@8b200000 {
+			reg = <0x0 0x8b200000 0x0 0x500000>;
+			no-map;
+		};
+
 		ipa_fw_mem: memory@8b700000 {
 			reg = <0 0x8b700000 0 0x10000>;
 			no-map;
@@ -157,6 +173,9 @@
 					   &LITTLE_CPU_SLEEP_1
 					   &CLUSTER_SLEEP_0>;
 			next-level-cache = <&L2_0>;
+			operating-points-v2 = <&cpu0_opp_table>;
+			interconnects = <&gem_noc MASTER_APPSS_PROC 3 &mc_virt SLAVE_EBI1 3>,
+					<&epss_l3 MASTER_EPSS_L3_APPS &epss_l3 SLAVE_EPSS_L3_SHARED>;
 			qcom,freq-domain = <&cpufreq_hw 0>;
 			#cooling-cells = <2>;
 			L2_0: l2-cache {
@@ -177,6 +196,9 @@
 					   &LITTLE_CPU_SLEEP_1
 					   &CLUSTER_SLEEP_0>;
 			next-level-cache = <&L2_100>;
+			operating-points-v2 = <&cpu0_opp_table>;
+			interconnects = <&gem_noc MASTER_APPSS_PROC 3 &mc_virt SLAVE_EBI1 3>,
+					<&epss_l3 MASTER_EPSS_L3_APPS &epss_l3 SLAVE_EPSS_L3_SHARED>;
 			qcom,freq-domain = <&cpufreq_hw 0>;
 			#cooling-cells = <2>;
 			L2_100: l2-cache {
@@ -194,6 +216,9 @@
 					   &LITTLE_CPU_SLEEP_1
 					   &CLUSTER_SLEEP_0>;
 			next-level-cache = <&L2_200>;
+			operating-points-v2 = <&cpu0_opp_table>;
+			interconnects = <&gem_noc MASTER_APPSS_PROC 3 &mc_virt SLAVE_EBI1 3>,
+					<&epss_l3 MASTER_EPSS_L3_APPS &epss_l3 SLAVE_EPSS_L3_SHARED>;
 			qcom,freq-domain = <&cpufreq_hw 0>;
 			#cooling-cells = <2>;
 			L2_200: l2-cache {
@@ -211,6 +236,9 @@
 					   &LITTLE_CPU_SLEEP_1
 					   &CLUSTER_SLEEP_0>;
 			next-level-cache = <&L2_300>;
+			operating-points-v2 = <&cpu0_opp_table>;
+			interconnects = <&gem_noc MASTER_APPSS_PROC 3 &mc_virt SLAVE_EBI1 3>,
+					<&epss_l3 MASTER_EPSS_L3_APPS &epss_l3 SLAVE_EPSS_L3_SHARED>;
 			qcom,freq-domain = <&cpufreq_hw 0>;
 			#cooling-cells = <2>;
 			L2_300: l2-cache {
@@ -228,6 +256,9 @@
 					   &BIG_CPU_SLEEP_1
 					   &CLUSTER_SLEEP_0>;
 			next-level-cache = <&L2_400>;
+			operating-points-v2 = <&cpu4_opp_table>;
+			interconnects = <&gem_noc MASTER_APPSS_PROC 3 &mc_virt SLAVE_EBI1 3>,
+					<&epss_l3 MASTER_EPSS_L3_APPS &epss_l3 SLAVE_EPSS_L3_SHARED>;
 			qcom,freq-domain = <&cpufreq_hw 1>;
 			#cooling-cells = <2>;
 			L2_400: l2-cache {
@@ -245,6 +276,9 @@
 					   &BIG_CPU_SLEEP_1
 					   &CLUSTER_SLEEP_0>;
 			next-level-cache = <&L2_500>;
+			operating-points-v2 = <&cpu4_opp_table>;
+			interconnects = <&gem_noc MASTER_APPSS_PROC 3 &mc_virt SLAVE_EBI1 3>,
+					<&epss_l3 MASTER_EPSS_L3_APPS &epss_l3 SLAVE_EPSS_L3_SHARED>;
 			qcom,freq-domain = <&cpufreq_hw 1>;
 			#cooling-cells = <2>;
 			L2_500: l2-cache {
@@ -262,6 +296,9 @@
 					   &BIG_CPU_SLEEP_1
 					   &CLUSTER_SLEEP_0>;
 			next-level-cache = <&L2_600>;
+			operating-points-v2 = <&cpu4_opp_table>;
+			interconnects = <&gem_noc MASTER_APPSS_PROC 3 &mc_virt SLAVE_EBI1 3>,
+					<&epss_l3 MASTER_EPSS_L3_APPS &epss_l3 SLAVE_EPSS_L3_SHARED>;
 			qcom,freq-domain = <&cpufreq_hw 1>;
 			#cooling-cells = <2>;
 			L2_600: l2-cache {
@@ -279,6 +316,9 @@
 					   &BIG_CPU_SLEEP_1
 					   &CLUSTER_SLEEP_0>;
 			next-level-cache = <&L2_700>;
+			operating-points-v2 = <&cpu7_opp_table>;
+			interconnects = <&gem_noc MASTER_APPSS_PROC 3 &mc_virt SLAVE_EBI1 3>,
+					<&epss_l3 MASTER_EPSS_L3_APPS &epss_l3 SLAVE_EPSS_L3_SHARED>;
 			qcom,freq-domain = <&cpufreq_hw 2>;
 			#cooling-cells = <2>;
 			L2_700: l2-cache {
@@ -378,6 +418,211 @@
 		};
 	};
 
+	cpu0_opp_table: opp-table-cpu0 {
+		compatible = "operating-points-v2";
+		opp-shared;
+
+		cpu0_opp_300mhz: opp-300000000 {
+			opp-hz = /bits/ 64 <300000000>;
+			opp-peak-kBps = <800000 9600000>;
+		};
+
+		cpu0_opp_691mhz: opp-691200000 {
+			opp-hz = /bits/ 64 <691200000>;
+			opp-peak-kBps = <800000 17817600>;
+		};
+
+		cpu0_opp_806mhz: opp-806400000 {
+			opp-hz = /bits/ 64 <806400000>;
+			opp-peak-kBps = <800000 20889600>;
+		};
+
+		cpu0_opp_941mhz: opp-940800000 {
+			opp-hz = /bits/ 64 <940800000>;
+			opp-peak-kBps = <1804000 24576000>;
+		};
+
+		cpu0_opp_1152mhz: opp-1152000000 {
+			opp-hz = /bits/ 64 <1152000000>;
+			opp-peak-kBps = <2188000 27033600>;
+		};
+
+		cpu0_opp_1325mhz: opp-1324800000 {
+			opp-hz = /bits/ 64 <1324800000>;
+			opp-peak-kBps = <2188000 33792000>;
+		};
+
+		cpu0_opp_1517mhz: opp-1516800000 {
+			opp-hz = /bits/ 64 <1516800000>;
+			opp-peak-kBps = <3072000 38092800>;
+		};
+
+		cpu0_opp_1651mhz: opp-1651200000 {
+			opp-hz = /bits/ 64 <1651200000>;
+			opp-peak-kBps = <3072000 41779200>;
+		};
+
+		cpu0_opp_1805mhz: opp-1804800000 {
+			opp-hz = /bits/ 64 <1804800000>;
+			opp-peak-kBps = <4068000 48537600>;
+		};
+
+		cpu0_opp_1958mhz: opp-1958400000 {
+			opp-hz = /bits/ 64 <1958400000>;
+			opp-peak-kBps = <4068000 48537600>;
+		};
+
+		cpu0_opp_2016mhz: opp-2016000000 {
+			opp-hz = /bits/ 64 <2016000000>;
+			opp-peak-kBps = <6220000 48537600>;
+		};
+	};
+
+	cpu4_opp_table: opp-table-cpu4 {
+		compatible = "operating-points-v2";
+		opp-shared;
+
+		cpu4_opp_691mhz: opp-691200000 {
+			opp-hz = /bits/ 64 <691200000>;
+			opp-peak-kBps = <1804000 9600000>;
+		};
+
+		cpu4_opp_941mhz: opp-940800000 {
+			opp-hz = /bits/ 64 <940800000>;
+			opp-peak-kBps = <2188000 17817600>;
+		};
+
+		cpu4_opp_1229mhz: opp-1228800000 {
+			opp-hz = /bits/ 64 <1228800000>;
+			opp-peak-kBps = <4068000 24576000>;
+		};
+
+		cpu4_opp_1344mhz: opp-1344000000 {
+			opp-hz = /bits/ 64 <1344000000>;
+			opp-peak-kBps = <4068000 24576000>;
+		};
+
+		cpu4_opp_1517mhz: opp-1516800000 {
+			opp-hz = /bits/ 64 <1516800000>;
+			opp-peak-kBps = <4068000 24576000>;
+		};
+
+		cpu4_opp_1651mhz: opp-1651200000 {
+			opp-hz = /bits/ 64 <1651200000>;
+			opp-peak-kBps = <6220000 38092800>;
+		};
+
+		cpu4_opp_1901mhz: opp-1900800000 {
+			opp-hz = /bits/ 64 <1900800000>;
+			opp-peak-kBps = <6220000 44851200>;
+		};
+
+		cpu4_opp_2054mhz: opp-2054400000 {
+			opp-hz = /bits/ 64 <2054400000>;
+			opp-peak-kBps = <6220000 44851200>;
+		};
+
+		cpu4_opp_2112mhz: opp-2112000000 {
+			opp-hz = /bits/ 64 <2112000000>;
+			opp-peak-kBps = <6220000 44851200>;
+		};
+
+		cpu4_opp_2131mhz: opp-2131200000 {
+			opp-hz = /bits/ 64 <2131200000>;
+			opp-peak-kBps = <6220000 44851200>;
+		};
+
+		cpu4_opp_2208mhz: opp-2208000000 {
+			opp-hz = /bits/ 64 <2208000000>;
+			opp-peak-kBps = <6220000 44851200>;
+		};
+
+		cpu4_opp_2400mhz: opp-2400000000 {
+			opp-hz = /bits/ 64 <2400000000>;
+			opp-peak-kBps = <8532000 48537600>;
+		};
+
+		cpu4_opp_2611mhz: opp-2611200000 {
+			opp-hz = /bits/ 64 <2611200000>;
+			opp-peak-kBps = <8532000 48537600>;
+		};
+	};
+
+	cpu7_opp_table: opp-table-cpu7 {
+		compatible = "operating-points-v2";
+		opp-shared;
+
+		cpu7_opp_806mhz: opp-806400000 {
+			opp-hz = /bits/ 64 <806400000>;
+			opp-peak-kBps = <1804000 9600000>;
+		};
+
+		cpu7_opp_1056mhz: opp-1056000000 {
+			opp-hz = /bits/ 64 <1056000000>;
+			opp-peak-kBps = <2188000 17817600>;
+		};
+
+		cpu7_opp_1325mhz: opp-1324800000 {
+			opp-hz = /bits/ 64 <1324800000>;
+			opp-peak-kBps = <4068000 24576000>;
+		};
+
+		cpu7_opp_1517mhz: opp-1516800000 {
+			opp-hz = /bits/ 64 <1516800000>;
+			opp-peak-kBps = <4068000 24576000>;
+		};
+
+		cpu7_opp_1766mhz: opp-1766400000 {
+			opp-hz = /bits/ 64 <1766400000>;
+			opp-peak-kBps = <6220000 38092800>;
+		};
+
+		cpu7_opp_1862mhz: opp-1862400000 {
+			opp-hz = /bits/ 64 <1862400000>;
+			opp-peak-kBps = <6220000 38092800>;
+		};
+
+		cpu7_opp_2035mhz: opp-2035200000 {
+			opp-hz = /bits/ 64 <2035200000>;
+			opp-peak-kBps = <6220000 38092800>;
+		};
+
+		cpu7_opp_2112mhz: opp-2112000000 {
+			opp-hz = /bits/ 64 <2112000000>;
+			opp-peak-kBps = <6220000 44851200>;
+		};
+
+		cpu7_opp_2208mhz: opp-2208000000 {
+			opp-hz = /bits/ 64 <2208000000>;
+			opp-peak-kBps = <6220000 44851200>;
+		};
+
+		cpu7_opp_2381mhz: opp-2380800000 {
+			opp-hz = /bits/ 64 <2380800000>;
+			opp-peak-kBps = <6832000 44851200>;
+		};
+
+		cpu7_opp_2400mhz: opp-2400000000 {
+			opp-hz = /bits/ 64 <2400000000>;
+			opp-peak-kBps = <8532000 48537600>;
+		};
+
+		cpu7_opp_2515mhz: opp-2515200000 {
+			opp-hz = /bits/ 64 <2515200000>;
+			opp-peak-kBps = <8532000 48537600>;
+		};
+
+		cpu7_opp_2707mhz: opp-2707200000 {
+			opp-hz = /bits/ 64 <2707200000>;
+			opp-peak-kBps = <8532000 48537600>;
+		};
+
+		cpu7_opp_3014mhz: opp-3014400000 {
+			opp-hz = /bits/ 64 <3014400000>;
+			opp-peak-kBps = <8532000 48537600>;
+		};
+	};
+
 	memory@80000000 {
 		device_type = "memory";
 		/* We expect the bootloader to fill in the size */
@@ -519,7 +764,7 @@
 		method = "smc";
 	};
 
-	qspi_opp_table: qspi-opp-table {
+	qspi_opp_table: opp-table-qspi {
 		compatible = "operating-points-v2";
 
 		opp-75000000 {
@@ -543,7 +788,7 @@
 		};
 	};
 
-	qup_opp_table: qup-opp-table {
+	qup_opp_table: opp-table-qup {
 		compatible = "operating-points-v2";
 
 		opp-75000000 {
@@ -574,15 +819,17 @@
 			reg = <0 0x00100000 0 0x1f0000>;
 			clocks = <&rpmhcc RPMH_CXO_CLK>,
 				 <&rpmhcc RPMH_CXO_CLK_A>, <&sleep_clk>,
-				 <0>, <0>, <0>, <0>, <0>, <0>;
+				 <0>, <&pcie1_lane>,
+				 <0>, <0>, <0>, <0>;
 			clock-names = "bi_tcxo", "bi_tcxo_ao", "sleep_clk",
-				      "pcie_0_pipe_clk", "pcie_1_pipe-clk",
+				      "pcie_0_pipe_clk", "pcie_1_pipe_clk",
 				      "ufs_phy_rx_symbol_0_clk", "ufs_phy_rx_symbol_1_clk",
 				      "ufs_phy_tx_symbol_0_clk",
 				      "usb3_phy_wrapper_gcc_usb30_pipe_clk";
 			#clock-cells = <1>;
 			#reset-cells = <1>;
 			#power-domain-cells = <1>;
+			power-domains = <&rpmhpd SC7280_CX>;
 		};
 
 		ipcc: mailbox@408000 {
@@ -605,10 +852,18 @@
 			power-domains = <&rpmhpd SC7280_MX>;
 			#address-cells = <1>;
 			#size-cells = <1>;
+
+			gpu_speed_bin: gpu_speed_bin@1e9 {
+				reg = <0x1e9 0x2>;
+				bits = <5 8>;
+			};
 		};
 
-		sdhc_1: sdhci@7c4000 {
+		sdhc_1: mmc@7c4000 {
 			compatible = "qcom,sc7280-sdhci", "qcom,sdhci-msm-v5";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&sdc1_clk>, <&sdc1_cmd>, <&sdc1_data>, <&sdc1_rclk>;
+			pinctrl-1 = <&sdc1_clk_sleep>, <&sdc1_cmd_sleep>, <&sdc1_data_sleep>, <&sdc1_rclk_sleep>;
 			status = "disabled";
 
 			reg = <0 0x007c4000 0 0x1000>,
@@ -620,10 +875,10 @@
 				     <GIC_SPI 656 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "hc_irq", "pwr_irq";
 
-			clocks = <&gcc GCC_SDCC1_APPS_CLK>,
-				 <&gcc GCC_SDCC1_AHB_CLK>,
+			clocks = <&gcc GCC_SDCC1_AHB_CLK>,
+				 <&gcc GCC_SDCC1_APPS_CLK>,
 				 <&rpmhcc RPMH_CXO_CLK>;
-			clock-names = "core", "iface", "xo";
+			clock-names = "iface", "core", "xo";
 			interconnects = <&aggre1_noc MASTER_SDCC_1 0 &mc_virt SLAVE_EBI1 0>,
 					<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_SDCC_1 0>;
 			interconnect-names = "sdhc-ddr","cpu-sdhc";
@@ -641,6 +896,8 @@
 			mmc-hs400-1_8v;
 			mmc-hs400-enhanced-strobe;
 
+			resets = <&gcc GCC_SDCC1_BCR>;
+
 			sdhc1_opp_table: opp-table {
 				compatible = "operating-points-v2";
 
@@ -661,6 +918,28 @@
 
 		};
 
+		gpi_dma0: dma-controller@900000 {
+			#dma-cells = <3>;
+			compatible = "qcom,sc7280-gpi-dma";
+			reg = <0 0x00900000 0 0x60000>;
+			interrupts = <GIC_SPI 244 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 245 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 246 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 247 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 248 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 249 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 250 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 251 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 252 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 253 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 254 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 255 IRQ_TYPE_LEVEL_HIGH>;
+			dma-channels = <12>;
+			dma-channel-mask = <0x7f>;
+			iommus = <&apps_smmu 0x0136 0x0>;
+			status = "disabled";
+		};
+
 		qupv3_id_0: geniqup@9c0000 {
 			compatible = "qcom,geni-se-qup";
 			reg = <0 0x009c0000 0 0x2000>;
@@ -688,6 +967,9 @@
 						<&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
 				interconnect-names = "qup-core", "qup-config",
 							"qup-memory";
+				dmas = <&gpi_dma0 0 0 QCOM_GPI_I2C>,
+				       <&gpi_dma0 1 0 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 
@@ -706,6 +988,9 @@
 				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
 						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
 				interconnect-names = "qup-core", "qup-config";
+				dmas = <&gpi_dma0 0 0 QCOM_GPI_SPI>,
+				       <&gpi_dma0 1 0 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 
@@ -740,6 +1025,9 @@
 						<&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
 				interconnect-names = "qup-core", "qup-config",
 							"qup-memory";
+				dmas = <&gpi_dma0 0 1 QCOM_GPI_I2C>,
+				       <&gpi_dma0 1 1 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 
@@ -758,6 +1046,9 @@
 				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
 						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
 				interconnect-names = "qup-core", "qup-config";
+				dmas = <&gpi_dma0 0 1 QCOM_GPI_SPI>,
+				       <&gpi_dma0 1 1 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 
@@ -792,6 +1083,9 @@
 						<&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
 				interconnect-names = "qup-core", "qup-config",
 							"qup-memory";
+				dmas = <&gpi_dma0 0 2 QCOM_GPI_I2C>,
+				       <&gpi_dma0 1 2 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 
@@ -810,6 +1104,9 @@
 				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
 						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
 				interconnect-names = "qup-core", "qup-config";
+				dmas = <&gpi_dma0 0 2 QCOM_GPI_SPI>,
+				       <&gpi_dma0 1 2 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 
@@ -844,6 +1141,9 @@
 						<&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
 				interconnect-names = "qup-core", "qup-config",
 							"qup-memory";
+				dmas = <&gpi_dma0 0 3 QCOM_GPI_I2C>,
+				       <&gpi_dma0 1 3 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 
@@ -862,6 +1162,9 @@
 				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
 						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
 				interconnect-names = "qup-core", "qup-config";
+				dmas = <&gpi_dma0 0 3 QCOM_GPI_SPI>,
+				       <&gpi_dma0 1 3 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 
@@ -896,6 +1199,9 @@
 						<&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
 				interconnect-names = "qup-core", "qup-config",
 							"qup-memory";
+				dmas = <&gpi_dma0 0 4 QCOM_GPI_I2C>,
+				       <&gpi_dma0 1 4 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 
@@ -914,6 +1220,9 @@
 				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
 						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
 				interconnect-names = "qup-core", "qup-config";
+				dmas = <&gpi_dma0 0 4 QCOM_GPI_SPI>,
+				       <&gpi_dma0 1 4 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 
@@ -948,6 +1257,9 @@
 						<&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
 				interconnect-names = "qup-core", "qup-config",
 							"qup-memory";
+				dmas = <&gpi_dma0 0 5 QCOM_GPI_I2C>,
+				       <&gpi_dma0 1 5 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 
@@ -966,6 +1278,9 @@
 				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
 						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
 				interconnect-names = "qup-core", "qup-config";
+				dmas = <&gpi_dma0 0 5 QCOM_GPI_SPI>,
+				       <&gpi_dma0 1 5 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 
@@ -1000,6 +1315,9 @@
 						<&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
 				interconnect-names = "qup-core", "qup-config",
 							"qup-memory";
+				dmas = <&gpi_dma0 0 6 QCOM_GPI_I2C>,
+				       <&gpi_dma0 1 6 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 
@@ -1018,6 +1336,9 @@
 				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
 						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
 				interconnect-names = "qup-core", "qup-config";
+				dmas = <&gpi_dma0 0 6 QCOM_GPI_SPI>,
+				       <&gpi_dma0 1 6 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 
@@ -1052,6 +1373,9 @@
 						<&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
 				interconnect-names = "qup-core", "qup-config",
 							"qup-memory";
+				dmas = <&gpi_dma0 0 7 QCOM_GPI_I2C>,
+				       <&gpi_dma0 1 7 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 
@@ -1070,6 +1394,9 @@
 				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
 						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_0 0>;
 				interconnect-names = "qup-core", "qup-config";
+				dmas = <&gpi_dma0 0 7 QCOM_GPI_SPI>,
+				       <&gpi_dma0 1 7 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 
@@ -1090,6 +1417,28 @@
 			};
 		};
 
+		gpi_dma1: dma-controller@a00000 {
+			#dma-cells = <3>;
+			compatible = "qcom,sc7280-gpi-dma";
+			reg = <0 0x00a00000 0 0x60000>;
+			interrupts = <GIC_SPI 279 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 280 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 281 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 282 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 283 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 284 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 293 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 294 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 295 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 296 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 297 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 298 IRQ_TYPE_LEVEL_HIGH>;
+			dma-channels = <12>;
+			dma-channel-mask = <0x1e>;
+			iommus = <&apps_smmu 0x56 0x0>;
+			status = "disabled";
+		};
+
 		qupv3_id_1: geniqup@ac0000 {
 			compatible = "qcom,geni-se-qup";
 			reg = <0 0x00ac0000 0 0x2000>;
@@ -1117,6 +1466,9 @@
 						<&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
 				interconnect-names = "qup-core", "qup-config",
 							"qup-memory";
+				dmas = <&gpi_dma1 0 0 QCOM_GPI_I2C>,
+				       <&gpi_dma1 1 0 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 
@@ -1135,6 +1487,9 @@
 				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
 						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
 				interconnect-names = "qup-core", "qup-config";
+				dmas = <&gpi_dma1 0 0 QCOM_GPI_SPI>,
+				       <&gpi_dma1 1 0 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 
@@ -1169,6 +1524,9 @@
 						<&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
 				interconnect-names = "qup-core", "qup-config",
 							"qup-memory";
+				dmas = <&gpi_dma1 0 1 QCOM_GPI_I2C>,
+				       <&gpi_dma1 1 1 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 
@@ -1187,6 +1545,9 @@
 				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
 						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
 				interconnect-names = "qup-core", "qup-config";
+				dmas = <&gpi_dma1 0 1 QCOM_GPI_SPI>,
+				       <&gpi_dma1 1 1 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 
@@ -1221,6 +1582,9 @@
 						<&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
 				interconnect-names = "qup-core", "qup-config",
 							"qup-memory";
+				dmas = <&gpi_dma1 0 2 QCOM_GPI_I2C>,
+				       <&gpi_dma1 1 2 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 
@@ -1239,6 +1603,9 @@
 				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
 						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
 				interconnect-names = "qup-core", "qup-config";
+				dmas = <&gpi_dma1 0 2 QCOM_GPI_SPI>,
+				       <&gpi_dma1 1 2 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 
@@ -1273,6 +1640,9 @@
 						<&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
 				interconnect-names = "qup-core", "qup-config",
 							"qup-memory";
+				dmas = <&gpi_dma1 0 3 QCOM_GPI_I2C>,
+				       <&gpi_dma1 1 3 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 
@@ -1291,6 +1661,9 @@
 				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
 						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
 				interconnect-names = "qup-core", "qup-config";
+				dmas = <&gpi_dma1 0 3 QCOM_GPI_SPI>,
+				       <&gpi_dma1 1 3 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 
@@ -1325,6 +1698,9 @@
 						<&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
 				interconnect-names = "qup-core", "qup-config",
 							"qup-memory";
+				dmas = <&gpi_dma1 0 4 QCOM_GPI_I2C>,
+				       <&gpi_dma1 1 4 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 
@@ -1343,6 +1719,9 @@
 				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
 						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
 				interconnect-names = "qup-core", "qup-config";
+				dmas = <&gpi_dma1 0 4 QCOM_GPI_SPI>,
+				       <&gpi_dma1 1 4 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 
@@ -1377,6 +1756,9 @@
 						<&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
 				interconnect-names = "qup-core", "qup-config",
 							"qup-memory";
+				dmas = <&gpi_dma1 0 5 QCOM_GPI_I2C>,
+				       <&gpi_dma1 1 5 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 
@@ -1395,6 +1777,9 @@
 				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
 						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
 				interconnect-names = "qup-core", "qup-config";
+				dmas = <&gpi_dma1 0 5 QCOM_GPI_SPI>,
+				       <&gpi_dma1 1 5 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 
@@ -1429,6 +1814,9 @@
 						<&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
 				interconnect-names = "qup-core", "qup-config",
 							"qup-memory";
+				dmas = <&gpi_dma1 0 6 QCOM_GPI_I2C>,
+				       <&gpi_dma1 1 6 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 
@@ -1447,6 +1835,9 @@
 				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
 						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
 				interconnect-names = "qup-core", "qup-config";
+				dmas = <&gpi_dma1 0 6 QCOM_GPI_SPI>,
+				       <&gpi_dma1 1 6 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 
@@ -1481,6 +1872,9 @@
 						<&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
 				interconnect-names = "qup-core", "qup-config",
 							"qup-memory";
+				dmas = <&gpi_dma1 0 7 QCOM_GPI_I2C>,
+				       <&gpi_dma1 1 7 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 
@@ -1499,6 +1893,9 @@
 				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
 						<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_QUP_1 0>;
 				interconnect-names = "qup-core", "qup-config";
+				dmas = <&gpi_dma1 0 7 QCOM_GPI_SPI>,
+				       <&gpi_dma1 1 7 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 
@@ -1568,6 +1965,47 @@
 			qcom,bcm-voters = <&apps_bcm_voter>;
 		};
 
+		wifi: wifi@17a10040 {
+			compatible = "qcom,wcn6750-wifi";
+			reg = <0 0x17a10040 0 0x0>;
+			iommus = <&apps_smmu 0x1c00 0x1>;
+			interrupts = <GIC_SPI 768 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 769 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 770 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 771 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 772 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 773 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 774 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 775 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 776 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 777 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 778 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 779 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 780 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 781 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 782 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 783 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 784 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 785 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 786 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 787 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 788 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 789 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 790 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 791 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 792 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 793 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 794 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 795 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 796 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 797 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 798 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 799 IRQ_TYPE_EDGE_RISING>;
+			qcom,rproc = <&remoteproc_wpss>;
+			memory-region = <&wlan_fw_mem>, <&wlan_ce_mem>;
+			status = "disabled";
+		};
+
 		pcie1: pci@1c08000 {
 			compatible = "qcom,pcie-sc7280";
 			reg = <0 0x01c08000 0 0x3000>,
@@ -1592,14 +2030,14 @@
 			interrupt-names = "msi";
 			#interrupt-cells = <1>;
 			interrupt-map-mask = <0 0 0 0x7>;
-			interrupt-map = <0 0 0 1 &intc 0 434 IRQ_TYPE_LEVEL_HIGH>,
-					<0 0 0 2 &intc 0 435 IRQ_TYPE_LEVEL_HIGH>,
-					<0 0 0 3 &intc 0 438 IRQ_TYPE_LEVEL_HIGH>,
-					<0 0 0 4 &intc 0 439 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-map = <0 0 0 1 &intc 0 0 0 434 IRQ_TYPE_LEVEL_HIGH>,
+					<0 0 0 2 &intc 0 0 0 435 IRQ_TYPE_LEVEL_HIGH>,
+					<0 0 0 3 &intc 0 0 0 438 IRQ_TYPE_LEVEL_HIGH>,
+					<0 0 0 4 &intc 0 0 0 439 IRQ_TYPE_LEVEL_HIGH>;
 
 			clocks = <&gcc GCC_PCIE_1_PIPE_CLK>,
 				 <&gcc GCC_PCIE_1_PIPE_CLK_SRC>,
-				 <&pcie1_lane 0>,
+				 <&pcie1_lane>,
 				 <&rpmhcc RPMH_CXO_CLK>,
 				 <&gcc GCC_PCIE_1_AUX_CLK>,
 				 <&gcc GCC_PCIE_1_CFG_AHB_CLK>,
@@ -1607,7 +2045,9 @@
 				 <&gcc GCC_PCIE_1_SLV_AXI_CLK>,
 				 <&gcc GCC_PCIE_1_SLV_Q2A_AXI_CLK>,
 				 <&gcc GCC_AGGRE_NOC_PCIE_TBU_CLK>,
-				 <&gcc GCC_DDRSS_PCIE_SF_CLK>;
+				 <&gcc GCC_DDRSS_PCIE_SF_CLK>,
+				 <&gcc GCC_AGGRE_NOC_PCIE_CENTER_SF_AXI_CLK>,
+				 <&gcc GCC_AGGRE_NOC_PCIE_1_AXI_CLK>;
 
 			clock-names = "pipe",
 				      "pipe_mux",
@@ -1619,7 +2059,9 @@
 				      "bus_slave",
 				      "slave_q2a",
 				      "tbu",
-				      "ddrss_sf_tbu";
+				      "ddrss_sf_tbu",
+				      "aggre0",
+				      "aggre1";
 
 			assigned-clocks = <&gcc GCC_PCIE_1_AUX_CLK>;
 			assigned-clock-rates = <19200000>;
@@ -1663,7 +2105,7 @@
 
 			status = "disabled";
 
-			pcie1_lane: lanes@1c0e200 {
+			pcie1_lane: phy@1c0e200 {
 				reg = <0 0x01c0e200 0 0x170>,
 				      <0 0x01c0e400 0 0x200>,
 				      <0 0x01c0ea00 0 0x1f0>,
@@ -1674,7 +2116,7 @@
 				clock-names = "pipe0";
 
 				#phy-cells = <0>;
-				#clock-cells = <1>;
+				#clock-cells = <0>;
 				clock-output-names = "pcie_1_pipe_clk";
 			};
 		};
@@ -1708,6 +2150,8 @@
 			interconnect-names = "memory",
 					     "config";
 
+			qcom,qmp = <&aoss_qmp>;
+
 			qcom,smem-states = <&ipa_smp2p_out 0>,
 					   <&ipa_smp2p_out 1>;
 			qcom,smem-state-names = "ipa-clock-enabled-valid",
@@ -1717,12 +2161,17 @@
 		};
 
 		tcsr_mutex: hwlock@1f40000 {
-			compatible = "qcom,tcsr-mutex", "syscon";
-			reg = <0 0x01f40000 0 0x40000>;
+			compatible = "qcom,tcsr-mutex";
+			reg = <0 0x01f40000 0 0x20000>;
 			#hwlock-cells = <1>;
 		};
 
-		tcsr: syscon@1fc0000 {
+		tcsr_1: syscon@1f60000 {
+			compatible = "qcom,sc7280-tcsr", "syscon";
+			reg = <0 0x01f60000 0 0x20000>;
+		};
+
+		tcsr_2: syscon@1fc0000 {
 			compatible = "qcom,sc7280-tcsr", "syscon";
 			reg = <0 0x01fc0000 0 0x30000>;
 		};
@@ -1730,14 +2179,244 @@
 		lpasscc: lpasscc@3000000 {
 			compatible = "qcom,sc7280-lpasscc";
 			reg = <0 0x03000000 0 0x40>,
-			      <0 0x03c04000 0 0x4>,
-			      <0 0x03389000 0 0x24>;
-			reg-names = "qdsp6ss", "top_cc", "cc";
+			      <0 0x03c04000 0 0x4>;
+			reg-names = "qdsp6ss", "top_cc";
 			clocks = <&gcc GCC_CFG_NOC_LPASS_CLK>;
 			clock-names = "iface";
 			#clock-cells = <1>;
 		};
 
+		lpass_rx_macro: codec@3200000 {
+			compatible = "qcom,sc7280-lpass-rx-macro";
+			reg = <0 0x03200000 0 0x1000>;
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&lpass_rx_swr_clk>, <&lpass_rx_swr_data>;
+
+			clocks = <&lpass_aon LPASS_AON_CC_TX_MCLK_CLK>,
+				 <&lpass_aon LPASS_AON_CC_TX_MCLK_2X_CLK>,
+				 <&lpass_va_macro>;
+			clock-names = "mclk", "npl", "fsgen";
+
+			power-domains = <&lpass_hm LPASS_CORE_CC_LPASS_CORE_HM_GDSC>,
+					<&lpass_aon LPASS_AON_CC_LPASS_AUDIO_HM_GDSC>;
+			power-domain-names = "macro", "dcodec";
+
+			#clock-cells = <0>;
+			#sound-dai-cells = <1>;
+
+			status = "disabled";
+		};
+
+		swr0: soundwire@3210000 {
+			compatible = "qcom,soundwire-v1.6.0";
+			reg = <0 0x03210000 0 0x2000>;
+
+			interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&lpass_rx_macro>;
+			clock-names = "iface";
+
+			qcom,din-ports = <0>;
+			qcom,dout-ports = <5>;
+
+			resets = <&lpass_audiocc LPASS_AUDIO_SWR_RX_CGCR>;
+			reset-names = "swr_audio_cgcr";
+
+			qcom,ports-word-length =	/bits/ 8 <0x01 0x07 0x04 0xff 0xff>;
+			qcom,ports-sinterval-low =	/bits/ 8 <0x03 0x3f 0x1f 0x03 0x03>;
+			qcom,ports-offset1 =		/bits/ 8 <0x00 0x00 0x0b 0x01 0x01>;
+			qcom,ports-offset2 =		/bits/ 8 <0x00 0x00 0x0b 0x00 0x00>;
+			qcom,ports-lane-control =	/bits/ 8 <0x01 0x00 0x00 0x00 0x00>;
+			qcom,ports-block-pack-mode =	/bits/ 8 <0xff 0x00 0x01 0xff 0xff>;
+			qcom,ports-hstart =		/bits/ 8 <0xff 0x03 0xff 0xff 0xff>;
+			qcom,ports-hstop =		/bits/ 8 <0xff 0x06 0xff 0xff 0xff>;
+			qcom,ports-block-group-count =	/bits/ 8 <0xff 0xff 0xff 0xff 0x00>;
+
+			#sound-dai-cells = <1>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+
+			status = "disabled";
+		};
+
+		lpass_tx_macro: codec@3220000 {
+			compatible = "qcom,sc7280-lpass-tx-macro";
+			reg = <0 0x03220000 0 0x1000>;
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&lpass_tx_swr_clk>, <&lpass_tx_swr_data>;
+
+			clocks = <&lpass_aon LPASS_AON_CC_TX_MCLK_CLK>,
+				 <&lpass_aon LPASS_AON_CC_TX_MCLK_2X_CLK>,
+				 <&lpass_va_macro>;
+			clock-names = "mclk", "npl", "fsgen";
+
+			power-domains = <&lpass_hm LPASS_CORE_CC_LPASS_CORE_HM_GDSC>,
+					<&lpass_aon LPASS_AON_CC_LPASS_AUDIO_HM_GDSC>;
+			power-domain-names = "macro", "dcodec";
+
+			#clock-cells = <0>;
+			#sound-dai-cells = <1>;
+
+			status = "disabled";
+		};
+
+		swr1: soundwire@3230000 {
+			compatible = "qcom,soundwire-v1.6.0";
+			reg = <0 0x03230000 0 0x2000>;
+
+			interrupts-extended = <&intc GIC_SPI 496 IRQ_TYPE_LEVEL_HIGH>,
+					      <&pdc 130 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&lpass_tx_macro>;
+			clock-names = "iface";
+
+			qcom,din-ports = <3>;
+			qcom,dout-ports = <0>;
+
+			resets = <&lpass_audiocc LPASS_AUDIO_SWR_TX_CGCR>;
+			reset-names = "swr_audio_cgcr";
+
+			qcom,ports-sinterval-low =	/bits/ 8 <0x01 0x03 0x03>;
+			qcom,ports-offset1 =		/bits/ 8 <0x01 0x00 0x02>;
+			qcom,ports-offset2 =		/bits/ 8 <0x00 0x00 0x00>;
+			qcom,ports-hstart =		/bits/ 8 <0xff 0xff 0xff>;
+			qcom,ports-hstop =		/bits/ 8 <0xff 0xff 0xff>;
+			qcom,ports-word-length =	/bits/ 8 <0xff 0x00 0xff>;
+			qcom,ports-block-pack-mode =	/bits/ 8 <0xff 0xff 0xff>;
+			qcom,ports-block-group-count =	/bits/ 8 <0xff 0xff 0xff>;
+			qcom,ports-lane-control =	/bits/ 8 <0x00 0x01 0x00>;
+			qcom,port-offset = <1>;
+
+			#sound-dai-cells = <1>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+
+			status = "disabled";
+		};
+
+		lpass_audiocc: clock-controller@3300000 {
+			compatible = "qcom,sc7280-lpassaudiocc";
+			reg = <0 0x03300000 0 0x30000>;
+			clocks = <&rpmhcc RPMH_CXO_CLK>,
+			       <&lpass_aon LPASS_AON_CC_MAIN_RCG_CLK_SRC>;
+			clock-names = "bi_tcxo", "lpass_aon_cc_main_rcg_clk_src";
+			power-domains = <&lpass_aon LPASS_AON_CC_LPASS_AUDIO_HM_GDSC>;
+			#clock-cells = <1>;
+			#power-domain-cells = <1>;
+			#reset-cells = <1>;
+		};
+
+		lpass_va_macro: codec@3370000 {
+			compatible = "qcom,sc7280-lpass-va-macro";
+			reg = <0 0x03370000 0 0x1000>;
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&lpass_dmic01_clk>, <&lpass_dmic01_data>;
+
+			clocks = <&lpass_aon LPASS_AON_CC_TX_MCLK_CLK>;
+			clock-names = "mclk";
+
+			power-domains = <&lpass_hm LPASS_CORE_CC_LPASS_CORE_HM_GDSC>,
+					<&lpass_aon LPASS_AON_CC_LPASS_AUDIO_HM_GDSC>;
+			power-domain-names = "macro", "dcodec";
+
+			#clock-cells = <0>;
+			#sound-dai-cells = <1>;
+
+			status = "disabled";
+		};
+
+		lpass_aon: clock-controller@3380000 {
+			compatible = "qcom,sc7280-lpassaoncc";
+			reg = <0 0x03380000 0 0x30000>;
+			clocks = <&rpmhcc RPMH_CXO_CLK>,
+			       <&rpmhcc RPMH_CXO_CLK_A>,
+			       <&lpass_core LPASS_CORE_CC_CORE_CLK>;
+			clock-names = "bi_tcxo", "bi_tcxo_ao", "iface";
+			#clock-cells = <1>;
+			#power-domain-cells = <1>;
+		};
+
+		lpass_core: clock-controller@3900000 {
+			compatible = "qcom,sc7280-lpasscorecc";
+			reg = <0 0x03900000 0 0x50000>;
+			clocks = <&rpmhcc RPMH_CXO_CLK>;
+			clock-names = "bi_tcxo";
+			power-domains = <&lpass_hm LPASS_CORE_CC_LPASS_CORE_HM_GDSC>;
+			#clock-cells = <1>;
+			#power-domain-cells = <1>;
+		};
+
+		lpass_cpu: audio@3987000 {
+			compatible = "qcom,sc7280-lpass-cpu";
+
+			reg = <0 0x03987000 0 0x68000>,
+			      <0 0x03b00000 0 0x29000>,
+			      <0 0x03260000 0 0xc000>,
+			      <0 0x03280000 0 0x29000>,
+			      <0 0x03340000 0 0x29000>,
+			      <0 0x0336c000 0 0x3000>;
+			reg-names = "lpass-hdmiif",
+				    "lpass-lpaif",
+				    "lpass-rxtx-cdc-dma-lpm",
+				    "lpass-rxtx-lpaif",
+				    "lpass-va-lpaif",
+				    "lpass-va-cdc-dma-lpm";
+
+			iommus = <&apps_smmu 0x1820 0>,
+				 <&apps_smmu 0x1821 0>,
+				 <&apps_smmu 0x1832 0>;
+
+			power-domains =	<&rpmhpd SC7280_LCX>;
+			power-domain-names = "lcx";
+			required-opps = <&rpmhpd_opp_nom>;
+
+			clocks = <&lpass_aon LPASS_AON_CC_AUDIO_HM_H_CLK>,
+				 <&lpass_core LPASS_CORE_CC_EXT_MCLK0_CLK>,
+				 <&lpass_core LPASS_CORE_CC_SYSNOC_MPORT_CORE_CLK>,
+				 <&lpass_core LPASS_CORE_CC_EXT_IF0_IBIT_CLK>,
+				 <&lpass_core LPASS_CORE_CC_EXT_IF1_IBIT_CLK>,
+				 <&lpass_audiocc LPASS_AUDIO_CC_CODEC_MEM_CLK>,
+				 <&lpass_audiocc LPASS_AUDIO_CC_CODEC_MEM0_CLK>,
+				 <&lpass_audiocc LPASS_AUDIO_CC_CODEC_MEM1_CLK>,
+				 <&lpass_audiocc LPASS_AUDIO_CC_CODEC_MEM2_CLK>,
+				 <&lpass_aon LPASS_AON_CC_VA_MEM0_CLK>;
+			clock-names = "aon_cc_audio_hm_h",
+				      "audio_cc_ext_mclk0",
+				      "core_cc_sysnoc_mport_core",
+				      "core_cc_ext_if0_ibit",
+				      "core_cc_ext_if1_ibit",
+				      "audio_cc_codec_mem",
+				      "audio_cc_codec_mem0",
+				      "audio_cc_codec_mem1",
+				      "audio_cc_codec_mem2",
+				      "aon_cc_va_mem0";
+
+			#sound-dai-cells = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			interrupts = <GIC_SPI 160 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 268 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 176 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 180 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "lpass-irq-lpaif",
+					  "lpass-irq-hdmi",
+					  "lpass-irq-vaif",
+					  "lpass-irq-rxtxif";
+
+			status = "disabled";
+		};
+
+		lpass_hm: clock-controller@3c00000 {
+			compatible = "qcom,sc7280-lpasshm";
+			reg = <0 0x3c00000 0 0x28>;
+			clocks = <&rpmhcc RPMH_CXO_CLK>;
+			clock-names = "bi_tcxo";
+			#clock-cells = <1>;
+			#power-domain-cells = <1>;
+		};
+
 		lpass_ag_noc: interconnect@3c40000 {
 			reg = <0 0x03c40000 0 0xf080>;
 			compatible = "qcom,sc7280-lpass-ag-noc";
@@ -1745,9 +2424,100 @@
 			qcom,bcm-voters = <&apps_bcm_voter>;
 		};
 
+		lpass_tlmm: pinctrl@33c0000 {
+			compatible = "qcom,sc7280-lpass-lpi-pinctrl";
+			reg = <0 0x033c0000 0x0 0x20000>,
+				<0 0x03550000 0x0 0x10000>;
+			qcom,adsp-bypass-mode;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&lpass_tlmm 0 0 15>;
+
+			#clock-cells = <1>;
+
+			lpass_dmic01_clk: dmic01-clk {
+				pins = "gpio6";
+				function = "dmic1_clk";
+			};
+
+			lpass_dmic01_clk_sleep: dmic01-clk-sleep {
+				pins = "gpio6";
+				function = "dmic1_clk";
+			};
+
+			lpass_dmic01_data: dmic01-data {
+				pins = "gpio7";
+				function = "dmic1_data";
+			};
+
+			lpass_dmic01_data_sleep: dmic01-data-sleep {
+				pins = "gpio7";
+				function = "dmic1_data";
+			};
+
+			lpass_dmic23_clk: dmic23-clk {
+				pins = "gpio8";
+				function = "dmic2_clk";
+			};
+
+			lpass_dmic23_clk_sleep: dmic23-clk-sleep {
+				pins = "gpio8";
+				function = "dmic2_clk";
+			};
+
+			lpass_dmic23_data: dmic23-data {
+				pins = "gpio9";
+				function = "dmic2_data";
+			};
+
+			lpass_dmic23_data_sleep: dmic23-data-sleep {
+				pins = "gpio9";
+				function = "dmic2_data";
+			};
+
+			lpass_rx_swr_clk: rx-swr-clk {
+				pins = "gpio3";
+				function = "swr_rx_clk";
+			};
+
+			lpass_rx_swr_clk_sleep: rx-swr-clk-sleep {
+				pins = "gpio3";
+				function = "swr_rx_clk";
+			};
+
+			lpass_rx_swr_data: rx-swr-data {
+				pins = "gpio4", "gpio5";
+				function = "swr_rx_data";
+			};
+
+			lpass_rx_swr_data_sleep: rx-swr-data-sleep {
+				pins = "gpio4", "gpio5";
+				function = "swr_rx_data";
+			};
+
+			lpass_tx_swr_clk: tx-swr-clk {
+				pins = "gpio0";
+				function = "swr_tx_clk";
+			};
+
+			lpass_tx_swr_clk_sleep: tx-swr-clk-sleep {
+				pins = "gpio0";
+				function = "swr_tx_clk";
+			};
+
+			lpass_tx_swr_data: tx-swr-data {
+				pins = "gpio1", "gpio2", "gpio14";
+				function = "swr_tx_data";
+			};
+
+			lpass_tx_swr_data_sleep: tx-swr-data-sleep {
+				pins = "gpio1", "gpio2", "gpio14";
+				function = "swr_tx_data";
+			};
+		};
+
 		gpu: gpu@3d00000 {
 			compatible = "qcom,adreno-635.0", "qcom,adreno";
-			#stream-id-cells = <16>;
 			reg = <0 0x03d00000 0 0x40000>,
 			      <0 0x03d9e000 0 0x1000>,
 			      <0 0x03d61000 0 0x800>;
@@ -1762,6 +2532,9 @@
 			interconnect-names = "gfx-mem";
 			#cooling-cells = <2>;
 
+			nvmem-cells = <&gpu_speed_bin>;
+			nvmem-cell-names = "speed_bin";
+
 			gpu_opp_table: opp-table {
 				compatible = "operating-points-v2";
 
@@ -1769,24 +2542,70 @@
 					opp-hz = /bits/ 64 <315000000>;
 					opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>;
 					opp-peak-kBps = <1804000>;
+					opp-supported-hw = <0x03>;
 				};
 
 				opp-450000000 {
 					opp-hz = /bits/ 64 <450000000>;
 					opp-level = <RPMH_REGULATOR_LEVEL_SVS>;
 					opp-peak-kBps = <4068000>;
+					opp-supported-hw = <0x03>;
+				};
+
+				/* Only applicable for SKUs which has 550Mhz as Fmax */
+				opp-550000000-0 {
+					opp-hz = /bits/ 64 <550000000>;
+					opp-level = <RPMH_REGULATOR_LEVEL_SVS_L1>;
+					opp-peak-kBps = <8368000>;
+					opp-supported-hw = <0x01>;
 				};
 
-				opp-550000000 {
+				opp-550000000-1 {
 					opp-hz = /bits/ 64 <550000000>;
 					opp-level = <RPMH_REGULATOR_LEVEL_SVS_L1>;
 					opp-peak-kBps = <6832000>;
+					opp-supported-hw = <0x02>;
+				};
+
+				opp-608000000 {
+					opp-hz = /bits/ 64 <608000000>;
+					opp-level = <RPMH_REGULATOR_LEVEL_SVS_L2>;
+					opp-peak-kBps = <8368000>;
+					opp-supported-hw = <0x02>;
+				};
+
+				opp-700000000 {
+					opp-hz = /bits/ 64 <700000000>;
+					opp-level = <RPMH_REGULATOR_LEVEL_NOM>;
+					opp-peak-kBps = <8532000>;
+					opp-supported-hw = <0x02>;
+				};
+
+				opp-812000000 {
+					opp-hz = /bits/ 64 <812000000>;
+					opp-level = <RPMH_REGULATOR_LEVEL_NOM_L1>;
+					opp-peak-kBps = <8532000>;
+					opp-supported-hw = <0x02>;
+				};
+
+				opp-840000000 {
+					opp-hz = /bits/ 64 <840000000>;
+					opp-level = <RPMH_REGULATOR_LEVEL_TURBO>;
+					opp-peak-kBps = <8532000>;
+					opp-supported-hw = <0x02>;
+				};
+
+				opp-900000000 {
+					opp-hz = /bits/ 64 <900000000>;
+					opp-level = <RPMH_REGULATOR_LEVEL_TURBO_L1>;
+					opp-peak-kBps = <8532000>;
+					opp-supported-hw = <0x02>;
 				};
 			};
 		};
 
-		gmu: gmu@3d69000 {
-			compatible="qcom,adreno-gmu-635.0", "qcom,adreno-gmu";
+		gmu: gmu@3d6a000 {
+			compatible = "qcom,adreno-gmu-635.0", "qcom,adreno-gmu";
 			reg = <0 0x03d6a000 0 0x34000>,
 				<0 0x3de0000 0 0x10000>,
 				<0 0x0b290000 0 0x10000>;
@@ -1794,13 +2613,13 @@
 			interrupts = <GIC_SPI 304 IRQ_TYPE_LEVEL_HIGH>,
 					<GIC_SPI 305 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "hfi", "gmu";
-			clocks = <&gpucc 5>,
-					<&gpucc 8>,
-					<&gcc GCC_DDRSS_GPU_AXI_CLK>,
-					<&gcc GCC_GPU_MEMNOC_GFX_CLK>,
-					<&gpucc 2>,
-					<&gpucc 15>,
-					<&gpucc 11>;
+			clocks = <&gpucc GPU_CC_CX_GMU_CLK>,
+				 <&gpucc GPU_CC_CXO_CLK>,
+				 <&gcc GCC_DDRSS_GPU_AXI_CLK>,
+				 <&gcc GCC_GPU_MEMNOC_GFX_CLK>,
+				 <&gpucc GPU_CC_AHB_CLK>,
+				 <&gpucc GPU_CC_HUB_CX_INT_CLK>,
+				 <&gpucc GPU_CC_HLOS1_VOTE_GPU_SMMU_CLK>;
 			clock-names = "gmu",
 				      "cxo",
 				      "axi",
@@ -1808,8 +2627,8 @@
 				      "ahb",
 				      "hub",
 				      "smmu_vote";
-			power-domains = <&gpucc 0>,
-					<&gpucc 1>;
+			power-domains = <&gpucc GPU_CC_CX_GDSC>,
+					<&gpucc GPU_CC_GX_GDSC>;
 			power-domain-names = "cx",
 					     "gx";
 			iommus = <&adreno_smmu 5 0x400>;
@@ -1858,12 +2677,12 @@
 					<GIC_SPI 687 IRQ_TYPE_LEVEL_HIGH>;
 
 			clocks = <&gcc GCC_GPU_MEMNOC_GFX_CLK>,
-					<&gcc GCC_GPU_SNOC_DVM_GFX_CLK>,
-					<&gpucc 2>,
-					<&gpucc 11>,
-					<&gpucc 5>,
-					<&gpucc 15>,
-					<&gpucc 13>;
+				 <&gcc GCC_GPU_SNOC_DVM_GFX_CLK>,
+				 <&gpucc GPU_CC_AHB_CLK>,
+				 <&gpucc GPU_CC_HLOS1_VOTE_GPU_SMMU_CLK>,
+				 <&gpucc GPU_CC_CX_GMU_CLK>,
+				 <&gpucc GPU_CC_HUB_CX_INT_CLK>,
+				 <&gpucc GPU_CC_HUB_AON_CLK>;
 			clock-names = "gcc_gpu_memnoc_gfx_clk",
 					"gcc_gpu_snoc_dvm_gfx_clk",
 					"gpu_cc_ahb_clk",
@@ -1872,7 +2691,7 @@
 					"gpu_cc_hub_cx_int_clk",
 					"gpu_cc_hub_aon_clk";
 
-			power-domains = <&gpucc 0>;
+			power-domains = <&gpucc GPU_CC_CX_GDSC>;
 		};
 
 		remoteproc_mpss: remoteproc@4080000 {
@@ -1911,9 +2730,9 @@
 				 <&pdc_reset PDC_MODEM_SYNC_RESET>;
 			reset-names = "mss_restart", "pdc_reset";
 
-			qcom,halt-regs = <&tcsr_mutex 0x23000 0x25000 0x28000 0x33000>;
-			qcom,ext-regs = <&tcsr 0x10000 0x10004 &tcsr_mutex 0x26004 0x26008>;
-			qcom,qaccept-regs = <&tcsr_mutex 0x23030 0x23040 0x23020>;
+			qcom,halt-regs = <&tcsr_1 0x3000 0x5000 0x8000 0x13000>;
+			qcom,ext-regs = <&tcsr_2 0x10000 0x10004 &tcsr_1 0x6004 0x6008>;
+			qcom,qaccept-regs = <&tcsr_1 0x3030 0x3040 0x3020>;
 
 			status = "disabled";
 
@@ -2417,8 +3236,11 @@
 			};
 		};
 
-		sdhc_2: sdhci@8804000 {
+		sdhc_2: mmc@8804000 {
 			compatible = "qcom,sc7280-sdhci", "qcom,sdhci-msm-v5";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&sdc2_clk>, <&sdc2_cmd>, <&sdc2_data>;
+			pinctrl-1 = <&sdc2_clk_sleep>, <&sdc2_cmd_sleep>, <&sdc2_data_sleep>;
 			status = "disabled";
 
 			reg = <0 0x08804000 0 0x1000>;
@@ -2428,10 +3250,10 @@
 				     <GIC_SPI 223 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "hc_irq", "pwr_irq";
 
-			clocks = <&gcc GCC_SDCC2_APPS_CLK>,
-				 <&gcc GCC_SDCC2_AHB_CLK>,
+			clocks = <&gcc GCC_SDCC2_AHB_CLK>,
+				 <&gcc GCC_SDCC2_APPS_CLK>,
 				 <&rpmhcc RPMH_CXO_CLK>;
-			clock-names = "core", "iface", "xo";
+			clock-names = "iface", "core", "xo";
 			interconnects = <&aggre1_noc MASTER_SDCC_2 0 &mc_virt SLAVE_EBI1 0>,
 					<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_SDCC_2 0>;
 			interconnect-names = "sdhc-ddr","cpu-sdhc";
@@ -2442,6 +3264,8 @@
 
 			qcom,dll-config = <0x0007642c>;
 
+			resets = <&gcc GCC_SDCC2_BCR>;
+
 			sdhc2_opp_table: opp-table {
 				compatible = "operating-points-v2";
 
@@ -2545,22 +3369,27 @@
 			clocks = <&gcc GCC_CFG_NOC_USB3_SEC_AXI_CLK>,
 				 <&gcc GCC_USB30_SEC_MASTER_CLK>,
 				 <&gcc GCC_AGGRE_USB3_SEC_AXI_CLK>,
-				 <&gcc GCC_USB30_SEC_MOCK_UTMI_CLK>,
-				 <&gcc GCC_USB30_SEC_SLEEP_CLK>;
-			clock-names = "cfg_noc", "core", "iface","mock_utmi",
-				      "sleep";
+				 <&gcc GCC_USB30_SEC_SLEEP_CLK>,
+				 <&gcc GCC_USB30_SEC_MOCK_UTMI_CLK>;
+			clock-names = "cfg_noc",
+				      "core",
+				      "iface",
+				      "sleep",
+				      "mock_utmi";
 
 			assigned-clocks = <&gcc GCC_USB30_SEC_MOCK_UTMI_CLK>,
 					  <&gcc GCC_USB30_SEC_MASTER_CLK>;
 			assigned-clock-rates = <19200000>, <200000000>;
 
 			interrupts-extended = <&intc GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>,
-				     <&pdc 13 IRQ_TYPE_EDGE_RISING>,
-				     <&pdc 12 IRQ_TYPE_EDGE_RISING>;
+					      <&pdc 12 IRQ_TYPE_EDGE_RISING>,
+					      <&pdc 13 IRQ_TYPE_EDGE_RISING>;
 			interrupt-names = "hs_phy_irq",
-					  "dm_hs_phy_irq", "dp_hs_phy_irq";
+					  "dp_hs_phy_irq",
+					  "dm_hs_phy_irq";
 
 			power-domains = <&gcc GCC_USB30_SEC_GDSC>;
+			required-opps = <&rpmhpd_opp_nom>;
 
 			resets = <&gcc GCC_USB30_SEC_BCR>;
 
@@ -2578,6 +3407,12 @@
 				phys = <&usb_2_hsphy>;
 				phy-names = "usb2-phy";
 				maximum-speed = "high-speed";
+				usb-role-switch;
+				port {
+					usb2_role_switch: endpoint {
+						remote-endpoint = <&eud_ep>;
+					};
+				};
 			};
 		};
 
@@ -2598,6 +3433,133 @@
 			status = "disabled";
 		};
 
+		remoteproc_wpss: remoteproc@8a00000 {
+			compatible = "qcom,sc7280-wpss-pil";
+			reg = <0 0x08a00000 0 0x10000>;
+
+			interrupts-extended = <&intc GIC_SPI 587 IRQ_TYPE_EDGE_RISING>,
+					      <&wpss_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
+					      <&wpss_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
+					      <&wpss_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
+					      <&wpss_smp2p_in 3 IRQ_TYPE_EDGE_RISING>,
+					      <&wpss_smp2p_in 7 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "wdog", "fatal", "ready", "handover",
+					  "stop-ack", "shutdown-ack";
+
+			clocks = <&gcc GCC_WPSS_AHB_BDG_MST_CLK>,
+				 <&gcc GCC_WPSS_AHB_CLK>,
+				 <&gcc GCC_WPSS_RSCP_CLK>,
+				 <&rpmhcc RPMH_CXO_CLK>;
+			clock-names = "ahb_bdg", "ahb",
+				      "rscp", "xo";
+
+			power-domains = <&rpmhpd SC7280_CX>,
+					<&rpmhpd SC7280_MX>;
+			power-domain-names = "cx", "mx";
+
+			memory-region = <&wpss_mem>;
+
+			qcom,qmp = <&aoss_qmp>;
+
+			qcom,smem-states = <&wpss_smp2p_out 0>;
+			qcom,smem-state-names = "stop";
+
+			resets = <&aoss_reset AOSS_CC_WCSS_RESTART>,
+				 <&pdc_reset PDC_WPSS_SYNC_RESET>;
+			reset-names = "restart", "pdc_sync";
+
+			qcom,halt-regs = <&tcsr_1 0x17000>;
+
+			status = "disabled";
+
+			glink-edge {
+				interrupts-extended = <&ipcc IPCC_CLIENT_WPSS
+							     IPCC_MPROC_SIGNAL_GLINK_QMP
+							     IRQ_TYPE_EDGE_RISING>;
+				mboxes = <&ipcc IPCC_CLIENT_WPSS
+						IPCC_MPROC_SIGNAL_GLINK_QMP>;
+
+				label = "wpss";
+				qcom,remote-pid = <13>;
+			};
+		};
+
+		pmu@9091000 {
+			compatible = "qcom,sc7280-llcc-bwmon";
+			reg = <0 0x9091000 0 0x1000>;
+
+			interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>;
+
+			interconnects = <&mc_virt MASTER_LLCC 3 &mc_virt SLAVE_EBI1 3>;
+
+			operating-points-v2 = <&llcc_bwmon_opp_table>;
+
+			llcc_bwmon_opp_table: opp-table {
+				compatible = "operating-points-v2";
+
+				opp-0 {
+					opp-peak-kBps = <800000>;
+				};
+				opp-1 {
+					opp-peak-kBps = <1804000>;
+				};
+				opp-2 {
+					opp-peak-kBps = <2188000>;
+				};
+				opp-3 {
+					opp-peak-kBps = <3072000>;
+				};
+				opp-4 {
+					opp-peak-kBps = <4068000>;
+				};
+				opp-5 {
+					opp-peak-kBps = <6220000>;
+				};
+				opp-6 {
+					opp-peak-kBps = <6832000>;
+				};
+				opp-7 {
+					opp-peak-kBps = <8532000>;
+				};
+			};
+		};
+
+		pmu@90b6400 {
+			compatible = "qcom,sc7280-cpu-bwmon", "qcom,msm8998-bwmon";
+			reg = <0 0x090b6400 0 0x600>;
+
+			interrupts = <GIC_SPI 581 IRQ_TYPE_LEVEL_HIGH>;
+
+			interconnects = <&gem_noc MASTER_APPSS_PROC 3 &gem_noc SLAVE_LLCC 3>;
+			operating-points-v2 = <&cpu_bwmon_opp_table>;
+
+			cpu_bwmon_opp_table: opp-table {
+				compatible = "operating-points-v2";
+
+				opp-0 {
+					opp-peak-kBps = <2400000>;
+				};
+				opp-1 {
+					opp-peak-kBps = <4800000>;
+				};
+				opp-2 {
+					opp-peak-kBps = <7456000>;
+				};
+				opp-3 {
+					opp-peak-kBps = <9600000>;
+				};
+				opp-4 {
+					opp-peak-kBps = <12896000>;
+				};
+				opp-5 {
+					opp-peak-kBps = <14928000>;
+				};
+				opp-6 {
+					opp-peak-kBps = <17056000>;
+				};
+			};
+		};
+
 		dc_noc: interconnect@90e0000 {
 			reg = <0 0x090e0000 0 0x5080>;
 			compatible = "qcom,sc7280-dc-noc";
@@ -2619,6 +3581,36 @@
 			interrupts = <GIC_SPI 582 IRQ_TYPE_LEVEL_HIGH>;
 		};
 
+		eud: eud@88e0000 {
+			compatible = "qcom,sc7280-eud","qcom,eud";
+			reg = <0 0x88e0000 0 0x2000>,
+			      <0 0x88e2000 0 0x1000>;
+			interrupts-extended = <&pdc 11 IRQ_TYPE_LEVEL_HIGH>;
+			ports {
+				port@0 {
+					eud_ep: endpoint {
+						remote-endpoint = <&usb2_role_switch>;
+					};
+				};
+				port@1 {
+					eud_con: endpoint {
+						remote-endpoint = <&con_eud>;
+					};
+				};
+			};
+		};
+
+		eud_typec: connector {
+			compatible = "usb-c-connector";
+			ports {
+				port@0 {
+					con_eud: endpoint {
+						remote-endpoint = <&eud_con>;
+					};
+				};
+			};
+		};
+
 		nsp_noc: interconnect@a0c0000 {
 			reg = <0 0x0a0c0000 0 0x10000>;
 			compatible = "qcom,sc7280-nsp-noc";
@@ -2638,23 +3630,29 @@
 			clocks = <&gcc GCC_CFG_NOC_USB3_PRIM_AXI_CLK>,
 				 <&gcc GCC_USB30_PRIM_MASTER_CLK>,
 				 <&gcc GCC_AGGRE_USB3_PRIM_AXI_CLK>,
-				 <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
-				 <&gcc GCC_USB30_PRIM_SLEEP_CLK>;
-			clock-names = "cfg_noc", "core", "iface", "mock_utmi",
-				      "sleep";
+				 <&gcc GCC_USB30_PRIM_SLEEP_CLK>,
+				 <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>;
+			clock-names = "cfg_noc",
+				      "core",
+				      "iface",
+				      "sleep",
+				      "mock_utmi";
 
 			assigned-clocks = <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
 					  <&gcc GCC_USB30_PRIM_MASTER_CLK>;
 			assigned-clock-rates = <19200000>, <200000000>;
 
 			interrupts-extended = <&intc GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>,
-					      <&pdc 14 IRQ_TYPE_EDGE_BOTH>,
+					      <&pdc 14 IRQ_TYPE_LEVEL_HIGH>,
 					      <&pdc 15 IRQ_TYPE_EDGE_BOTH>,
-					      <&pdc 17 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "hs_phy_irq", "dp_hs_phy_irq",
-					  "dm_hs_phy_irq", "ss_phy_irq";
+					      <&pdc 17 IRQ_TYPE_EDGE_BOTH>;
+			interrupt-names = "hs_phy_irq",
+					  "dp_hs_phy_irq",
+					  "dm_hs_phy_irq",
+					  "ss_phy_irq";
 
 			power-domains = <&gcc GCC_USB30_PRIM_GDSC>;
+			required-opps = <&rpmhpd_opp_nom>;
 
 			resets = <&gcc GCC_USB30_PRIM_BCR>;
 
@@ -2662,6 +3660,8 @@
 					<&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_USB3_0 0>;
 			interconnect-names = "usb-ddr", "apps-usb";
 
+			wakeup-source;
+
 			usb_1_dwc3: usb@a600000 {
 				compatible = "snps,dwc3";
 				reg = <0 0x0a600000 0 0xe000>;
@@ -2675,6 +3675,76 @@
 			};
 		};
 
+		venus: video-codec@aa00000 {
+			compatible = "qcom,sc7280-venus";
+			reg = <0 0x0aa00000 0 0xd0600>;
+			interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>;
+
+			clocks = <&videocc VIDEO_CC_MVSC_CORE_CLK>,
+				 <&videocc VIDEO_CC_MVSC_CTL_AXI_CLK>,
+				 <&videocc VIDEO_CC_VENUS_AHB_CLK>,
+				 <&videocc VIDEO_CC_MVS0_CORE_CLK>,
+				 <&videocc VIDEO_CC_MVS0_AXI_CLK>;
+			clock-names = "core", "bus", "iface",
+				      "vcodec_core", "vcodec_bus";
+
+			power-domains = <&videocc MVSC_GDSC>,
+					<&videocc MVS0_GDSC>,
+					<&rpmhpd SC7280_CX>;
+			power-domain-names = "venus", "vcodec0", "cx";
+			operating-points-v2 = <&venus_opp_table>;
+
+			interconnects = <&gem_noc MASTER_APPSS_PROC 0 &cnoc2 SLAVE_VENUS_CFG 0>,
+					<&mmss_noc MASTER_VIDEO_P0 0 &mc_virt SLAVE_EBI1 0>;
+			interconnect-names = "cpu-cfg", "video-mem";
+
+			iommus = <&apps_smmu 0x2180 0x20>,
+				 <&apps_smmu 0x2184 0x20>;
+			memory-region = <&video_mem>;
+
+			video-decoder {
+				compatible = "venus-decoder";
+			};
+
+			video-encoder {
+				compatible = "venus-encoder";
+			};
+
+			video-firmware {
+				iommus = <&apps_smmu 0x21a2 0x0>;
+			};
+
+			venus_opp_table: opp-table {
+				compatible = "operating-points-v2";
+
+				opp-133330000 {
+					opp-hz = /bits/ 64 <133330000>;
+					required-opps = <&rpmhpd_opp_low_svs>;
+				};
+
+				opp-240000000 {
+					opp-hz = /bits/ 64 <240000000>;
+					required-opps = <&rpmhpd_opp_svs>;
+				};
+
+				opp-335000000 {
+					opp-hz = /bits/ 64 <335000000>;
+					required-opps = <&rpmhpd_opp_svs_l1>;
+				};
+
+				opp-424000000 {
+					opp-hz = /bits/ 64 <424000000>;
+					required-opps = <&rpmhpd_opp_nom>;
+				};
+
+				opp-460000048 {
+					opp-hz = /bits/ 64 <460000048>;
+					required-opps = <&rpmhpd_opp_turbo>;
+				};
+			};
+
+		};
+
 		videocc: clock-controller@aaf0000 {
 			compatible = "qcom,sc7280-videocc";
 			reg = <0 0xaaf0000 0 0x10000>;
@@ -2686,13 +3756,31 @@
 			#power-domain-cells = <1>;
 		};
 
+		camcc: clock-controller@ad00000 {
+			compatible = "qcom,sc7280-camcc";
+			reg = <0 0x0ad00000 0 0x10000>;
+			clocks = <&rpmhcc RPMH_CXO_CLK>,
+				<&rpmhcc RPMH_CXO_CLK_A>,
+				<&sleep_clk>;
+			clock-names = "bi_tcxo", "bi_tcxo_ao", "sleep_clk";
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+			#power-domain-cells = <1>;
+		};
+
 		dispcc: clock-controller@af00000 {
 			compatible = "qcom,sc7280-dispcc";
 			reg = <0 0xaf00000 0 0x20000>;
 			clocks = <&rpmhcc RPMH_CXO_CLK>,
 				 <&gcc GCC_DISP_GPLL0_CLK_SRC>,
-				 <0>, <0>, <0>, <0>, <0>, <0>;
-			clock-names = "bi_tcxo", "gcc_disp_gpll0_clk",
+				 <&mdss_dsi_phy 0>,
+				 <&mdss_dsi_phy 1>,
+				 <&dp_phy 0>,
+				 <&dp_phy 1>,
+				 <&mdss_edp_phy 0>,
+				 <&mdss_edp_phy 1>;
+			clock-names = "bi_tcxo",
+				      "gcc_disp_gpll0_clk",
 				      "dsi0_phy_pll_out_byteclk",
 				      "dsi0_phy_pll_out_dsiclk",
 				      "dp_phy_pll_link_clk",
@@ -2704,6 +3792,379 @@
 			#power-domain-cells = <1>;
 		};
 
+		mdss: display-subsystem@ae00000 {
+			compatible = "qcom,sc7280-mdss";
+			reg = <0 0x0ae00000 0 0x1000>;
+			reg-names = "mdss";
+
+			power-domains = <&dispcc DISP_CC_MDSS_CORE_GDSC>;
+
+			clocks = <&gcc GCC_DISP_AHB_CLK>,
+				 <&dispcc DISP_CC_MDSS_AHB_CLK>,
+				<&dispcc DISP_CC_MDSS_MDP_CLK>;
+			clock-names = "iface",
+				      "ahb",
+				      "core";
+
+			interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-controller;
+			#interrupt-cells = <1>;
+
+			interconnects = <&mmss_noc MASTER_MDP0 0 &mc_virt SLAVE_EBI1 0>;
+			interconnect-names = "mdp0-mem";
+
+			iommus = <&apps_smmu 0x900 0x402>;
+
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+
+			status = "disabled";
+
+			mdss_mdp: display-controller@ae01000 {
+				compatible = "qcom,sc7280-dpu";
+				reg = <0 0x0ae01000 0 0x8f030>,
+					<0 0x0aeb0000 0 0x2008>;
+				reg-names = "mdp", "vbif";
+
+				clocks = <&gcc GCC_DISP_HF_AXI_CLK>,
+					<&gcc GCC_DISP_SF_AXI_CLK>,
+					<&dispcc DISP_CC_MDSS_AHB_CLK>,
+					<&dispcc DISP_CC_MDSS_MDP_LUT_CLK>,
+					<&dispcc DISP_CC_MDSS_MDP_CLK>,
+					<&dispcc DISP_CC_MDSS_VSYNC_CLK>;
+				clock-names = "bus",
+					      "nrt_bus",
+					      "iface",
+					      "lut",
+					      "core",
+					      "vsync";
+				assigned-clocks = <&dispcc DISP_CC_MDSS_VSYNC_CLK>,
+						<&dispcc DISP_CC_MDSS_AHB_CLK>;
+				assigned-clock-rates = <19200000>,
+							<19200000>;
+				operating-points-v2 = <&mdp_opp_table>;
+				power-domains = <&rpmhpd SC7280_CX>;
+
+				interrupt-parent = <&mdss>;
+				interrupts = <0>;
+
+				status = "disabled";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+						dpu_intf1_out: endpoint {
+							remote-endpoint = <&dsi0_in>;
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+						dpu_intf5_out: endpoint {
+							remote-endpoint = <&edp_in>;
+						};
+					};
+
+					port@2 {
+						reg = <2>;
+						dpu_intf0_out: endpoint {
+							remote-endpoint = <&dp_in>;
+						};
+					};
+				};
+
+				mdp_opp_table: opp-table {
+					compatible = "operating-points-v2";
+
+					opp-200000000 {
+						opp-hz = /bits/ 64 <200000000>;
+						required-opps = <&rpmhpd_opp_low_svs>;
+					};
+
+					opp-300000000 {
+						opp-hz = /bits/ 64 <300000000>;
+						required-opps = <&rpmhpd_opp_svs>;
+					};
+
+					opp-380000000 {
+						opp-hz = /bits/ 64 <380000000>;
+						required-opps = <&rpmhpd_opp_svs_l1>;
+					};
+
+					opp-506666667 {
+						opp-hz = /bits/ 64 <506666667>;
+						required-opps = <&rpmhpd_opp_nom>;
+					};
+				};
+			};
+
+			mdss_dsi: dsi@ae94000 {
+				compatible = "qcom,mdss-dsi-ctrl";
+				reg = <0 0x0ae94000 0 0x400>;
+				reg-names = "dsi_ctrl";
+
+				interrupt-parent = <&mdss>;
+				interrupts = <4>;
+
+				clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK>,
+					 <&dispcc DISP_CC_MDSS_BYTE0_INTF_CLK>,
+					 <&dispcc DISP_CC_MDSS_PCLK0_CLK>,
+					 <&dispcc DISP_CC_MDSS_ESC0_CLK>,
+					 <&dispcc DISP_CC_MDSS_AHB_CLK>,
+					 <&gcc GCC_DISP_HF_AXI_CLK>;
+				clock-names = "byte",
+					      "byte_intf",
+					      "pixel",
+					      "core",
+					      "iface",
+					      "bus";
+
+				operating-points-v2 = <&dsi_opp_table>;
+				power-domains = <&rpmhpd SC7280_CX>;
+
+				phys = <&mdss_dsi_phy>;
+				phy-names = "dsi";
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				status = "disabled";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+						dsi0_in: endpoint {
+							remote-endpoint = <&dpu_intf1_out>;
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+						dsi0_out: endpoint {
+						};
+					};
+				};
+
+				dsi_opp_table: opp-table {
+					compatible = "operating-points-v2";
+
+					opp-187500000 {
+						opp-hz = /bits/ 64 <187500000>;
+						required-opps = <&rpmhpd_opp_low_svs>;
+					};
+
+					opp-300000000 {
+						opp-hz = /bits/ 64 <300000000>;
+						required-opps = <&rpmhpd_opp_svs>;
+					};
+
+					opp-358000000 {
+						opp-hz = /bits/ 64 <358000000>;
+						required-opps = <&rpmhpd_opp_svs_l1>;
+					};
+				};
+			};
+
+			mdss_dsi_phy: phy@ae94400 {
+				compatible = "qcom,sc7280-dsi-phy-7nm";
+				reg = <0 0x0ae94400 0 0x200>,
+				      <0 0x0ae94600 0 0x280>,
+				      <0 0x0ae94900 0 0x280>;
+				reg-names = "dsi_phy",
+					    "dsi_phy_lane",
+					    "dsi_pll";
+
+				#clock-cells = <1>;
+				#phy-cells = <0>;
+
+				clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+					 <&rpmhcc RPMH_CXO_CLK>;
+				clock-names = "iface", "ref";
+
+				status = "disabled";
+			};
+
+			mdss_edp: edp@aea0000 {
+				compatible = "qcom,sc7280-edp";
+				pinctrl-names = "default";
+				pinctrl-0 = <&edp_hot_plug_det>;
+
+				reg = <0 0xaea0000 0 0x200>,
+				      <0 0xaea0200 0 0x200>,
+				      <0 0xaea0400 0 0xc00>,
+				      <0 0xaea1000 0 0x400>;
+
+				interrupt-parent = <&mdss>;
+				interrupts = <14>;
+
+				clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+					 <&dispcc DISP_CC_MDSS_EDP_AUX_CLK>,
+					 <&dispcc DISP_CC_MDSS_EDP_LINK_CLK>,
+					 <&dispcc DISP_CC_MDSS_EDP_LINK_INTF_CLK>,
+					 <&dispcc DISP_CC_MDSS_EDP_PIXEL_CLK>;
+				clock-names = "core_iface",
+					      "core_aux",
+					      "ctrl_link",
+					      "ctrl_link_iface",
+					      "stream_pixel";
+				assigned-clocks = <&dispcc DISP_CC_MDSS_EDP_LINK_CLK_SRC>,
+						  <&dispcc DISP_CC_MDSS_EDP_PIXEL_CLK_SRC>;
+				assigned-clock-parents = <&mdss_edp_phy 0>, <&mdss_edp_phy 1>;
+
+				phys = <&mdss_edp_phy>;
+				phy-names = "dp";
+
+				operating-points-v2 = <&edp_opp_table>;
+				power-domains = <&rpmhpd SC7280_CX>;
+
+				status = "disabled";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+						edp_in: endpoint {
+							remote-endpoint = <&dpu_intf5_out>;
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+						mdss_edp_out: endpoint { };
+					};
+				};
+
+				edp_opp_table: opp-table {
+					compatible = "operating-points-v2";
+
+					opp-160000000 {
+						opp-hz = /bits/ 64 <160000000>;
+						required-opps = <&rpmhpd_opp_low_svs>;
+					};
+
+					opp-270000000 {
+						opp-hz = /bits/ 64 <270000000>;
+						required-opps = <&rpmhpd_opp_svs>;
+					};
+
+					opp-540000000 {
+						opp-hz = /bits/ 64 <540000000>;
+						required-opps = <&rpmhpd_opp_nom>;
+					};
+
+					opp-810000000 {
+						opp-hz = /bits/ 64 <810000000>;
+						required-opps = <&rpmhpd_opp_nom>;
+					};
+				};
+			};
+
+			mdss_edp_phy: phy@aec2a00 {
+				compatible = "qcom,sc7280-edp-phy";
+
+				reg = <0 0xaec2a00 0 0x19c>,
+				      <0 0xaec2200 0 0xa0>,
+				      <0 0xaec2600 0 0xa0>,
+				      <0 0xaec2000 0 0x1c0>;
+
+				clocks = <&rpmhcc RPMH_CXO_CLK>,
+					 <&gcc GCC_EDP_CLKREF_EN>;
+				clock-names = "aux",
+					      "cfg_ahb";
+
+				#clock-cells = <1>;
+				#phy-cells = <0>;
+
+				status = "disabled";
+			};
+
+			mdss_dp: displayport-controller@ae90000 {
+				compatible = "qcom,sc7280-dp";
+
+				reg = <0 0xae90000 0 0x200>,
+				      <0 0xae90200 0 0x200>,
+				      <0 0xae90400 0 0xc00>,
+				      <0 0xae91000 0 0x400>,
+				      <0 0xae91400 0 0x400>;
+
+				interrupt-parent = <&mdss>;
+				interrupts = <12>;
+
+				clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
+					 <&dispcc DISP_CC_MDSS_DP_AUX_CLK>,
+					 <&dispcc DISP_CC_MDSS_DP_LINK_CLK>,
+					 <&dispcc DISP_CC_MDSS_DP_LINK_INTF_CLK>,
+					 <&dispcc DISP_CC_MDSS_DP_PIXEL_CLK>;
+				clock-names = "core_iface",
+						"core_aux",
+						"ctrl_link",
+						"ctrl_link_iface",
+						"stream_pixel";
+				assigned-clocks = <&dispcc DISP_CC_MDSS_DP_LINK_CLK_SRC>,
+						  <&dispcc DISP_CC_MDSS_DP_PIXEL_CLK_SRC>;
+				assigned-clock-parents = <&dp_phy 0>, <&dp_phy 1>;
+				phys = <&dp_phy>;
+				phy-names = "dp";
+
+				operating-points-v2 = <&dp_opp_table>;
+				power-domains = <&rpmhpd SC7280_CX>;
+
+				#sound-dai-cells = <0>;
+
+				status = "disabled";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+						dp_in: endpoint {
+							remote-endpoint = <&dpu_intf0_out>;
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+						dp_out: endpoint { };
+					};
+				};
+
+				dp_opp_table: opp-table {
+					compatible = "operating-points-v2";
+
+					opp-160000000 {
+						opp-hz = /bits/ 64 <160000000>;
+						required-opps = <&rpmhpd_opp_low_svs>;
+					};
+
+					opp-270000000 {
+						opp-hz = /bits/ 64 <270000000>;
+						required-opps = <&rpmhpd_opp_svs>;
+					};
+
+					opp-540000000 {
+						opp-hz = /bits/ 64 <540000000>;
+						required-opps = <&rpmhpd_opp_svs_l1>;
+					};
+
+					opp-810000000 {
+						opp-hz = /bits/ 64 <810000000>;
+						required-opps = <&rpmhpd_opp_nom>;
+					};
+				};
+			};
+		};
+
 		pdc: interrupt-controller@b220000 {
 			compatible = "qcom,sc7280-pdc", "qcom,pdc";
 			reg = <0 0x0b220000 0 0x30000>;
@@ -2752,7 +4213,7 @@
 		};
 
 		aoss_qmp: power-controller@c300000 {
-			compatible = "qcom,sc7280-aoss-qmp";
+			compatible = "qcom,sc7280-aoss-qmp", "qcom,aoss-qmp";
 			reg = <0 0x0c300000 0 0x400>;
 			interrupts-extended = <&ipcc IPCC_CLIENT_AOP
 						     IPCC_MPROC_SIGNAL_GLINK_QMP
@@ -2797,758 +4258,799 @@
 			gpio-ranges = <&tlmm 0 0 175>;
 			wakeup-parent = <&pdc>;
 
-			pcie1_clkreq_n: pcie1-clkreq-n {
+			dp_hot_plug_det: dp-hot-plug-det-pins {
+				pins = "gpio47";
+				function = "dp_hot";
+			};
+
+			edp_hot_plug_det: edp-hot-plug-det-pins {
+				pins = "gpio60";
+				function = "edp_hot";
+			};
+
+			mi2s0_data0: mi2s0-data0-pins {
+				pins = "gpio98";
+				function = "mi2s0_data0";
+			};
+
+			mi2s0_data1: mi2s0-data1-pins {
+				pins = "gpio99";
+				function = "mi2s0_data1";
+			};
+
+			mi2s0_mclk: mi2s0-mclk-pins {
+				pins = "gpio96";
+				function = "pri_mi2s";
+			};
+
+			mi2s0_sclk: mi2s0-sclk-pins {
+				pins = "gpio97";
+				function = "mi2s0_sck";
+			};
+
+			mi2s0_ws: mi2s0-ws-pins {
+				pins = "gpio100";
+				function = "mi2s0_ws";
+			};
+
+			mi2s1_data0: mi2s1-data0-pins {
+				pins = "gpio107";
+				function = "mi2s1_data0";
+			};
+
+			mi2s1_sclk: mi2s1-sclk-pins {
+				pins = "gpio106";
+				function = "mi2s1_sck";
+			};
+
+			mi2s1_ws: mi2s1-ws-pins {
+				pins = "gpio108";
+				function = "mi2s1_ws";
+			};
+
+			pcie1_clkreq_n: pcie1-clkreq-n-pins {
 				pins = "gpio79";
 				function = "pcie1_clkreqn";
-				drive-strength = <2>;
-				bias-pull-up;
 			};
 
-			qspi_clk: qspi-clk {
+			qspi_clk: qspi-clk-pins {
 				pins = "gpio14";
 				function = "qspi_clk";
 			};
 
-			qspi_cs0: qspi-cs0 {
+			qspi_cs0: qspi-cs0-pins {
 				pins = "gpio15";
 				function = "qspi_cs";
 			};
 
-			qspi_cs1: qspi-cs1 {
+			qspi_cs1: qspi-cs1-pins {
 				pins = "gpio19";
 				function = "qspi_cs";
 			};
 
-			qspi_data01: qspi-data01 {
+			qspi_data01: qspi-data01-pins {
 				pins = "gpio12", "gpio13";
 				function = "qspi_data";
 			};
 
-			qspi_data12: qspi-data12 {
+			qspi_data12: qspi-data12-pins {
 				pins = "gpio16", "gpio17";
 				function = "qspi_data";
 			};
 
-			qup_i2c0_data_clk: qup-i2c0-data-clk {
+			qup_i2c0_data_clk: qup-i2c0-data-clk-pins {
 				pins = "gpio0", "gpio1";
 				function = "qup00";
 			};
 
-			qup_i2c1_data_clk: qup-i2c1-data-clk {
+			qup_i2c1_data_clk: qup-i2c1-data-clk-pins {
 				pins = "gpio4", "gpio5";
 				function = "qup01";
 			};
 
-			qup_i2c2_data_clk: qup-i2c2-data-clk {
+			qup_i2c2_data_clk: qup-i2c2-data-clk-pins {
 				pins = "gpio8", "gpio9";
 				function = "qup02";
 			};
 
-			qup_i2c3_data_clk: qup-i2c3-data-clk {
+			qup_i2c3_data_clk: qup-i2c3-data-clk-pins {
 				pins = "gpio12", "gpio13";
 				function = "qup03";
 			};
 
-			qup_i2c4_data_clk: qup-i2c4-data-clk {
+			qup_i2c4_data_clk: qup-i2c4-data-clk-pins {
 				pins = "gpio16", "gpio17";
 				function = "qup04";
 			};
 
-			qup_i2c5_data_clk: qup-i2c5-data-clk {
+			qup_i2c5_data_clk: qup-i2c5-data-clk-pins {
 				pins = "gpio20", "gpio21";
 				function = "qup05";
 			};
 
-			qup_i2c6_data_clk: qup-i2c6-data-clk {
+			qup_i2c6_data_clk: qup-i2c6-data-clk-pins {
 				pins = "gpio24", "gpio25";
 				function = "qup06";
 			};
 
-			qup_i2c7_data_clk: qup-i2c7-data-clk {
+			qup_i2c7_data_clk: qup-i2c7-data-clk-pins {
 				pins = "gpio28", "gpio29";
 				function = "qup07";
 			};
 
-			qup_i2c8_data_clk: qup-i2c8-data-clk {
+			qup_i2c8_data_clk: qup-i2c8-data-clk-pins {
 				pins = "gpio32", "gpio33";
 				function = "qup10";
 			};
 
-			qup_i2c9_data_clk: qup-i2c9-data-clk {
+			qup_i2c9_data_clk: qup-i2c9-data-clk-pins {
 				pins = "gpio36", "gpio37";
 				function = "qup11";
 			};
 
-			qup_i2c10_data_clk: qup-i2c10-data-clk {
+			qup_i2c10_data_clk: qup-i2c10-data-clk-pins {
 				pins = "gpio40", "gpio41";
 				function = "qup12";
 			};
 
-			qup_i2c11_data_clk: qup-i2c11-data-clk {
+			qup_i2c11_data_clk: qup-i2c11-data-clk-pins {
 				pins = "gpio44", "gpio45";
 				function = "qup13";
 			};
 
-			qup_i2c12_data_clk: qup-i2c12-data-clk {
+			qup_i2c12_data_clk: qup-i2c12-data-clk-pins {
 				pins = "gpio48", "gpio49";
 				function = "qup14";
 			};
 
-			qup_i2c13_data_clk: qup-i2c13-data-clk {
+			qup_i2c13_data_clk: qup-i2c13-data-clk-pins {
 				pins = "gpio52", "gpio53";
 				function = "qup15";
 			};
 
-			qup_i2c14_data_clk: qup-i2c14-data-clk {
+			qup_i2c14_data_clk: qup-i2c14-data-clk-pins {
 				pins = "gpio56", "gpio57";
 				function = "qup16";
 			};
 
-			qup_i2c15_data_clk: qup-i2c15-data-clk {
+			qup_i2c15_data_clk: qup-i2c15-data-clk-pins {
 				pins = "gpio60", "gpio61";
 				function = "qup17";
 			};
 
-			qup_spi0_data_clk: qup-spi0-data-clk {
+			qup_spi0_data_clk: qup-spi0-data-clk-pins {
 				pins = "gpio0", "gpio1", "gpio2";
 				function = "qup00";
 			};
 
-			qup_spi0_cs: qup-spi0-cs {
+			qup_spi0_cs: qup-spi0-cs-pins {
 				pins = "gpio3";
 				function = "qup00";
 			};
 
-			qup_spi0_cs_gpio: qup-spi0-cs-gpio {
+			qup_spi0_cs_gpio: qup-spi0-cs-gpio-pins {
 				pins = "gpio3";
 				function = "gpio";
 			};
 
-			qup_spi1_data_clk: qup-spi1-data-clk {
+			qup_spi1_data_clk: qup-spi1-data-clk-pins {
 				pins = "gpio4", "gpio5", "gpio6";
 				function = "qup01";
 			};
 
-			qup_spi1_cs: qup-spi1-cs {
+			qup_spi1_cs: qup-spi1-cs-pins {
 				pins = "gpio7";
 				function = "qup01";
 			};
 
-			qup_spi1_cs_gpio: qup-spi1-cs-gpio {
+			qup_spi1_cs_gpio: qup-spi1-cs-gpio-pins {
 				pins = "gpio7";
 				function = "gpio";
 			};
 
-			qup_spi2_data_clk: qup-spi2-data-clk {
+			qup_spi2_data_clk: qup-spi2-data-clk-pins {
 				pins = "gpio8", "gpio9", "gpio10";
 				function = "qup02";
 			};
 
-			qup_spi2_cs: qup-spi2-cs {
+			qup_spi2_cs: qup-spi2-cs-pins {
 				pins = "gpio11";
 				function = "qup02";
 			};
 
-			qup_spi2_cs_gpio: qup-spi2-cs-gpio {
+			qup_spi2_cs_gpio: qup-spi2-cs-gpio-pins {
 				pins = "gpio11";
 				function = "gpio";
 			};
 
-			qup_spi3_data_clk: qup-spi3-data-clk {
+			qup_spi3_data_clk: qup-spi3-data-clk-pins {
 				pins = "gpio12", "gpio13", "gpio14";
 				function = "qup03";
 			};
 
-			qup_spi3_cs: qup-spi3-cs {
+			qup_spi3_cs: qup-spi3-cs-pins {
 				pins = "gpio15";
 				function = "qup03";
 			};
 
-			qup_spi3_cs_gpio: qup-spi3-cs-gpio {
+			qup_spi3_cs_gpio: qup-spi3-cs-gpio-pins {
 				pins = "gpio15";
 				function = "gpio";
 			};
 
-			qup_spi4_data_clk: qup-spi4-data-clk {
+			qup_spi4_data_clk: qup-spi4-data-clk-pins {
 				pins = "gpio16", "gpio17", "gpio18";
 				function = "qup04";
 			};
 
-			qup_spi4_cs: qup-spi4-cs {
+			qup_spi4_cs: qup-spi4-cs-pins {
 				pins = "gpio19";
 				function = "qup04";
 			};
 
-			qup_spi4_cs_gpio: qup-spi4-cs-gpio {
+			qup_spi4_cs_gpio: qup-spi4-cs-gpio-pins {
 				pins = "gpio19";
 				function = "gpio";
 			};
 
-			qup_spi5_data_clk: qup-spi5-data-clk {
+			qup_spi5_data_clk: qup-spi5-data-clk-pins {
 				pins = "gpio20", "gpio21", "gpio22";
 				function = "qup05";
 			};
 
-			qup_spi5_cs: qup-spi5-cs {
+			qup_spi5_cs: qup-spi5-cs-pins {
 				pins = "gpio23";
 				function = "qup05";
 			};
 
-			qup_spi5_cs_gpio: qup-spi5-cs-gpio {
+			qup_spi5_cs_gpio: qup-spi5-cs-gpio-pins {
 				pins = "gpio23";
 				function = "gpio";
 			};
 
-			qup_spi6_data_clk: qup-spi6-data-clk {
+			qup_spi6_data_clk: qup-spi6-data-clk-pins {
 				pins = "gpio24", "gpio25", "gpio26";
 				function = "qup06";
 			};
 
-			qup_spi6_cs: qup-spi6-cs {
+			qup_spi6_cs: qup-spi6-cs-pins {
 				pins = "gpio27";
 				function = "qup06";
 			};
 
-			qup_spi6_cs_gpio: qup-spi6-cs-gpio {
+			qup_spi6_cs_gpio: qup-spi6-cs-gpio-pins {
 				pins = "gpio27";
 				function = "gpio";
 			};
 
-			qup_spi7_data_clk: qup-spi7-data-clk {
+			qup_spi7_data_clk: qup-spi7-data-clk-pins {
 				pins = "gpio28", "gpio29", "gpio30";
 				function = "qup07";
 			};
 
-			qup_spi7_cs: qup-spi7-cs {
+			qup_spi7_cs: qup-spi7-cs-pins {
 				pins = "gpio31";
 				function = "qup07";
 			};
 
-			qup_spi7_cs_gpio: qup-spi7-cs-gpio {
+			qup_spi7_cs_gpio: qup-spi7-cs-gpio-pins {
 				pins = "gpio31";
 				function = "gpio";
 			};
 
-			qup_spi8_data_clk: qup-spi8-data-clk {
+			qup_spi8_data_clk: qup-spi8-data-clk-pins {
 				pins = "gpio32", "gpio33", "gpio34";
 				function = "qup10";
 			};
 
-			qup_spi8_cs: qup-spi8-cs {
+			qup_spi8_cs: qup-spi8-cs-pins {
 				pins = "gpio35";
 				function = "qup10";
 			};
 
-			qup_spi8_cs_gpio: qup-spi8-cs-gpio {
+			qup_spi8_cs_gpio: qup-spi8-cs-gpio-pins {
 				pins = "gpio35";
 				function = "gpio";
 			};
 
-			qup_spi9_data_clk: qup-spi9-data-clk {
+			qup_spi9_data_clk: qup-spi9-data-clk-pins {
 				pins = "gpio36", "gpio37", "gpio38";
 				function = "qup11";
 			};
 
-			qup_spi9_cs: qup-spi9-cs {
+			qup_spi9_cs: qup-spi9-cs-pins {
 				pins = "gpio39";
 				function = "qup11";
 			};
 
-			qup_spi9_cs_gpio: qup-spi9-cs-gpio {
+			qup_spi9_cs_gpio: qup-spi9-cs-gpio-pins {
 				pins = "gpio39";
 				function = "gpio";
 			};
 
-			qup_spi10_data_clk: qup-spi10-data-clk {
+			qup_spi10_data_clk: qup-spi10-data-clk-pins {
 				pins = "gpio40", "gpio41", "gpio42";
 				function = "qup12";
 			};
 
-			qup_spi10_cs: qup-spi10-cs {
+			qup_spi10_cs: qup-spi10-cs-pins {
 				pins = "gpio43";
 				function = "qup12";
 			};
 
-			qup_spi10_cs_gpio: qup-spi10-cs-gpio {
+			qup_spi10_cs_gpio: qup-spi10-cs-gpio-pins {
 				pins = "gpio43";
 				function = "gpio";
 			};
 
-			qup_spi11_data_clk: qup-spi11-data-clk {
+			qup_spi11_data_clk: qup-spi11-data-clk-pins {
 				pins = "gpio44", "gpio45", "gpio46";
 				function = "qup13";
 			};
 
-			qup_spi11_cs: qup-spi11-cs {
+			qup_spi11_cs: qup-spi11-cs-pins {
 				pins = "gpio47";
 				function = "qup13";
 			};
 
-			qup_spi11_cs_gpio: qup-spi11-cs-gpio {
+			qup_spi11_cs_gpio: qup-spi11-cs-gpio-pins {
 				pins = "gpio47";
 				function = "gpio";
 			};
 
-			qup_spi12_data_clk: qup-spi12-data-clk {
+			qup_spi12_data_clk: qup-spi12-data-clk-pins {
 				pins = "gpio48", "gpio49", "gpio50";
 				function = "qup14";
 			};
 
-			qup_spi12_cs: qup-spi12-cs {
+			qup_spi12_cs: qup-spi12-cs-pins {
 				pins = "gpio51";
 				function = "qup14";
 			};
 
-			qup_spi12_cs_gpio: qup-spi12-cs-gpio {
+			qup_spi12_cs_gpio: qup-spi12-cs-gpio-pins {
 				pins = "gpio51";
 				function = "gpio";
 			};
 
-			qup_spi13_data_clk: qup-spi13-data-clk {
+			qup_spi13_data_clk: qup-spi13-data-clk-pins {
 				pins = "gpio52", "gpio53", "gpio54";
 				function = "qup15";
 			};
 
-			qup_spi13_cs: qup-spi13-cs {
+			qup_spi13_cs: qup-spi13-cs-pins {
 				pins = "gpio55";
 				function = "qup15";
 			};
 
-			qup_spi13_cs_gpio: qup-spi13-cs-gpio {
+			qup_spi13_cs_gpio: qup-spi13-cs-gpio-pins {
 				pins = "gpio55";
 				function = "gpio";
 			};
 
-			qup_spi14_data_clk: qup-spi14-data-clk {
+			qup_spi14_data_clk: qup-spi14-data-clk-pins {
 				pins = "gpio56", "gpio57", "gpio58";
 				function = "qup16";
 			};
 
-			qup_spi14_cs: qup-spi14-cs {
+			qup_spi14_cs: qup-spi14-cs-pins {
 				pins = "gpio59";
 				function = "qup16";
 			};
 
-			qup_spi14_cs_gpio: qup-spi14-cs-gpio {
+			qup_spi14_cs_gpio: qup-spi14-cs-gpio-pins {
 				pins = "gpio59";
 				function = "gpio";
 			};
 
-			qup_spi15_data_clk: qup-spi15-data-clk {
+			qup_spi15_data_clk: qup-spi15-data-clk-pins {
 				pins = "gpio60", "gpio61", "gpio62";
 				function = "qup17";
 			};
 
-			qup_spi15_cs: qup-spi15-cs {
+			qup_spi15_cs: qup-spi15-cs-pins {
 				pins = "gpio63";
 				function = "qup17";
 			};
 
-			qup_spi15_cs_gpio: qup-spi15-cs-gpio {
+			qup_spi15_cs_gpio: qup-spi15-cs-gpio-pins {
 				pins = "gpio63";
 				function = "gpio";
 			};
 
-			qup_uart0_cts: qup-uart0-cts {
+			qup_uart0_cts: qup-uart0-cts-pins {
 				pins = "gpio0";
 				function = "qup00";
 			};
 
-			qup_uart0_rts: qup-uart0-rts {
+			qup_uart0_rts: qup-uart0-rts-pins {
 				pins = "gpio1";
 				function = "qup00";
 			};
 
-			qup_uart0_tx: qup-uart0-tx {
+			qup_uart0_tx: qup-uart0-tx-pins {
 				pins = "gpio2";
 				function = "qup00";
 			};
 
-			qup_uart0_rx: qup-uart0-rx {
+			qup_uart0_rx: qup-uart0-rx-pins {
 				pins = "gpio3";
 				function = "qup00";
 			};
 
-			qup_uart1_cts: qup-uart1-cts {
+			qup_uart1_cts: qup-uart1-cts-pins {
 				pins = "gpio4";
 				function = "qup01";
 			};
 
-			qup_uart1_rts: qup-uart1-rts {
+			qup_uart1_rts: qup-uart1-rts-pins {
 				pins = "gpio5";
 				function = "qup01";
 			};
 
-			qup_uart1_tx: qup-uart1-tx {
+			qup_uart1_tx: qup-uart1-tx-pins {
 				pins = "gpio6";
 				function = "qup01";
 			};
 
-			qup_uart1_rx: qup-uart1-rx {
+			qup_uart1_rx: qup-uart1-rx-pins {
 				pins = "gpio7";
 				function = "qup01";
 			};
 
-			qup_uart2_cts: qup-uart2-cts {
+			qup_uart2_cts: qup-uart2-cts-pins {
 				pins = "gpio8";
 				function = "qup02";
 			};
 
-			qup_uart2_rts: qup-uart2-rts {
+			qup_uart2_rts: qup-uart2-rts-pins {
 				pins = "gpio9";
 				function = "qup02";
 			};
 
-			qup_uart2_tx: qup-uart2-tx {
+			qup_uart2_tx: qup-uart2-tx-pins {
 				pins = "gpio10";
 				function = "qup02";
 			};
 
-			qup_uart2_rx: qup-uart2-rx {
+			qup_uart2_rx: qup-uart2-rx-pins {
 				pins = "gpio11";
 				function = "qup02";
 			};
 
-			qup_uart3_cts: qup-uart3-cts {
+			qup_uart3_cts: qup-uart3-cts-pins {
 				pins = "gpio12";
 				function = "qup03";
 			};
 
-			qup_uart3_rts: qup-uart3-rts {
+			qup_uart3_rts: qup-uart3-rts-pins {
 				pins = "gpio13";
 				function = "qup03";
 			};
 
-			qup_uart3_tx: qup-uart3-tx {
+			qup_uart3_tx: qup-uart3-tx-pins {
 				pins = "gpio14";
 				function = "qup03";
 			};
 
-			qup_uart3_rx: qup-uart3-rx {
+			qup_uart3_rx: qup-uart3-rx-pins {
 				pins = "gpio15";
 				function = "qup03";
 			};
 
-			qup_uart4_cts: qup-uart4-cts {
+			qup_uart4_cts: qup-uart4-cts-pins {
 				pins = "gpio16";
 				function = "qup04";
 			};
 
-			qup_uart4_rts: qup-uart4-rts {
+			qup_uart4_rts: qup-uart4-rts-pins {
 				pins = "gpio17";
 				function = "qup04";
 			};
 
-			qup_uart4_tx: qup-uart4-tx {
+			qup_uart4_tx: qup-uart4-tx-pins {
 				pins = "gpio18";
 				function = "qup04";
 			};
 
-			qup_uart4_rx: qup-uart4-rx {
+			qup_uart4_rx: qup-uart4-rx-pins {
 				pins = "gpio19";
 				function = "qup04";
 			};
 
-			qup_uart5_cts: qup-uart5-cts {
+			qup_uart5_cts: qup-uart5-cts-pins {
 				pins = "gpio20";
 				function = "qup05";
 			};
 
-			qup_uart5_rts: qup-uart5-rts {
+			qup_uart5_rts: qup-uart5-rts-pins {
 				pins = "gpio21";
 				function = "qup05";
 			};
 
-			qup_uart5_tx: qup-uart5-tx {
+			qup_uart5_tx: qup-uart5-tx-pins {
 				pins = "gpio22";
 				function = "qup05";
 			};
 
-			qup_uart5_rx: qup-uart5-rx {
+			qup_uart5_rx: qup-uart5-rx-pins {
 				pins = "gpio23";
 				function = "qup05";
 			};
 
-			qup_uart6_cts: qup-uart6-cts {
+			qup_uart6_cts: qup-uart6-cts-pins {
 				pins = "gpio24";
 				function = "qup06";
 			};
 
-			qup_uart6_rts: qup-uart6-rts {
+			qup_uart6_rts: qup-uart6-rts-pins {
 				pins = "gpio25";
 				function = "qup06";
 			};
 
-			qup_uart6_tx: qup-uart6-tx {
+			qup_uart6_tx: qup-uart6-tx-pins {
 				pins = "gpio26";
 				function = "qup06";
 			};
 
-			qup_uart6_rx: qup-uart6-rx {
+			qup_uart6_rx: qup-uart6-rx-pins {
 				pins = "gpio27";
 				function = "qup06";
 			};
 
-			qup_uart7_cts: qup-uart7-cts {
+			qup_uart7_cts: qup-uart7-cts-pins {
 				pins = "gpio28";
 				function = "qup07";
 			};
 
-			qup_uart7_rts: qup-uart7-rts {
+			qup_uart7_rts: qup-uart7-rts-pins {
 				pins = "gpio29";
 				function = "qup07";
 			};
 
-			qup_uart7_tx: qup-uart7-tx {
+			qup_uart7_tx: qup-uart7-tx-pins {
 				pins = "gpio30";
 				function = "qup07";
 			};
 
-			qup_uart7_rx: qup-uart7-rx {
+			qup_uart7_rx: qup-uart7-rx-pins {
 				pins = "gpio31";
 				function = "qup07";
 			};
 
-			sdc1_on: sdc1-on {
-				clk {
-					pins = "sdc1_clk";
-				};
-
-				cmd {
-					pins = "sdc1_cmd";
-				};
-
-				data {
-					pins = "sdc1_data";
-				};
-
-				rclk {
-					pins = "sdc1_rclk";
-				};
-			};
-
-			sdc1_off: sdc1-off {
-				clk {
-					pins = "sdc1_clk";
-					drive-strength = <2>;
-					bias-bus-hold;
-				};
-
-				cmd {
-					pins = "sdc1_cmd";
-					drive-strength = <2>;
-					bias-bus-hold;
-				};
-
-				data {
-					pins = "sdc1_data";
-					drive-strength = <2>;
-					bias-bus-hold;
-				};
-
-				rclk {
-					pins = "sdc1_rclk";
-					bias-bus-hold;
-				};
-			};
-
-			sdc2_on: sdc2-on {
-				clk {
-					pins = "sdc2_clk";
-				};
-
-				cmd {
-					pins = "sdc2_cmd";
-				};
-
-				data {
-					pins = "sdc2_data";
-				};
-			};
-
-			sdc2_off: sdc2-off {
-				clk {
-					pins = "sdc2_clk";
-					drive-strength = <2>;
-					bias-bus-hold;
-				};
-
-				cmd {
-					pins ="sdc2_cmd";
-					drive-strength = <2>;
-					bias-bus-hold;
-				};
-
-				data {
-					pins ="sdc2_data";
-					drive-strength = <2>;
-					bias-bus-hold;
-				};
-			};
-
-			qup_uart8_cts: qup-uart8-cts {
+			qup_uart8_cts: qup-uart8-cts-pins {
 				pins = "gpio32";
 				function = "qup10";
 			};
 
-			qup_uart8_rts: qup-uart8-rts {
+			qup_uart8_rts: qup-uart8-rts-pins {
 				pins = "gpio33";
 				function = "qup10";
 			};
 
-			qup_uart8_tx: qup-uart8-tx {
+			qup_uart8_tx: qup-uart8-tx-pins {
 				pins = "gpio34";
 				function = "qup10";
 			};
 
-			qup_uart8_rx: qup-uart8-rx {
+			qup_uart8_rx: qup-uart8-rx-pins {
 				pins = "gpio35";
 				function = "qup10";
 			};
 
-			qup_uart9_cts: qup-uart9-cts {
+			qup_uart9_cts: qup-uart9-cts-pins {
 				pins = "gpio36";
 				function = "qup11";
 			};
 
-			qup_uart9_rts: qup-uart9-rts {
+			qup_uart9_rts: qup-uart9-rts-pins {
 				pins = "gpio37";
 				function = "qup11";
 			};
 
-			qup_uart9_tx: qup-uart9-tx {
+			qup_uart9_tx: qup-uart9-tx-pins {
 				pins = "gpio38";
 				function = "qup11";
 			};
 
-			qup_uart9_rx: qup-uart9-rx {
+			qup_uart9_rx: qup-uart9-rx-pins {
 				pins = "gpio39";
 				function = "qup11";
 			};
 
-			qup_uart10_cts: qup-uart10-cts {
+			qup_uart10_cts: qup-uart10-cts-pins {
 				pins = "gpio40";
 				function = "qup12";
 			};
 
-			qup_uart10_rts: qup-uart10-rts {
+			qup_uart10_rts: qup-uart10-rts-pins {
 				pins = "gpio41";
 				function = "qup12";
 			};
 
-			qup_uart10_tx: qup-uart10-tx {
+			qup_uart10_tx: qup-uart10-tx-pins {
 				pins = "gpio42";
 				function = "qup12";
 			};
 
-			qup_uart10_rx: qup-uart10-rx {
+			qup_uart10_rx: qup-uart10-rx-pins {
 				pins = "gpio43";
 				function = "qup12";
 			};
 
-			qup_uart11_cts: qup-uart11-cts {
+			qup_uart11_cts: qup-uart11-cts-pins {
 				pins = "gpio44";
 				function = "qup13";
 			};
 
-			qup_uart11_rts: qup-uart11-rts {
+			qup_uart11_rts: qup-uart11-rts-pins {
 				pins = "gpio45";
 				function = "qup13";
 			};
 
-			qup_uart11_tx: qup-uart11-tx {
+			qup_uart11_tx: qup-uart11-tx-pins {
 				pins = "gpio46";
 				function = "qup13";
 			};
 
-			qup_uart11_rx: qup-uart11-rx {
+			qup_uart11_rx: qup-uart11-rx-pins {
 				pins = "gpio47";
 				function = "qup13";
 			};
 
-			qup_uart12_cts: qup-uart12-cts {
+			qup_uart12_cts: qup-uart12-cts-pins {
 				pins = "gpio48";
 				function = "qup14";
 			};
 
-			qup_uart12_rts: qup-uart12-rts {
+			qup_uart12_rts: qup-uart12-rts-pins {
 				pins = "gpio49";
 				function = "qup14";
 			};
 
-			qup_uart12_tx: qup-uart12-tx {
+			qup_uart12_tx: qup-uart12-tx-pins {
 				pins = "gpio50";
 				function = "qup14";
 			};
 
-			qup_uart12_rx: qup-uart12-rx {
+			qup_uart12_rx: qup-uart12-rx-pins {
 				pins = "gpio51";
 				function = "qup14";
 			};
 
-			qup_uart13_cts: qup-uart13-cts {
+			qup_uart13_cts: qup-uart13-cts-pins {
 				pins = "gpio52";
 				function = "qup15";
 			};
 
-			qup_uart13_rts: qup-uart13-rts {
+			qup_uart13_rts: qup-uart13-rts-pins {
 				pins = "gpio53";
 				function = "qup15";
 			};
 
-			qup_uart13_tx: qup-uart13-tx {
+			qup_uart13_tx: qup-uart13-tx-pins {
 				pins = "gpio54";
 				function = "qup15";
 			};
 
-			qup_uart13_rx: qup-uart13-rx {
+			qup_uart13_rx: qup-uart13-rx-pins {
 				pins = "gpio55";
 				function = "qup15";
 			};
 
-			qup_uart14_cts: qup-uart14-cts {
+			qup_uart14_cts: qup-uart14-cts-pins {
 				pins = "gpio56";
 				function = "qup16";
 			};
 
-			qup_uart14_rts: qup-uart14-rts {
+			qup_uart14_rts: qup-uart14-rts-pins {
 				pins = "gpio57";
 				function = "qup16";
 			};
 
-			qup_uart14_tx: qup-uart14-tx {
+			qup_uart14_tx: qup-uart14-tx-pins {
 				pins = "gpio58";
 				function = "qup16";
 			};
 
-			qup_uart14_rx: qup-uart14-rx {
+			qup_uart14_rx: qup-uart14-rx-pins {
 				pins = "gpio59";
 				function = "qup16";
 			};
 
-			qup_uart15_cts: qup-uart15-cts {
+			qup_uart15_cts: qup-uart15-cts-pins {
 				pins = "gpio60";
 				function = "qup17";
 			};
 
-			qup_uart15_rts: qup-uart15-rts {
+			qup_uart15_rts: qup-uart15-rts-pins {
 				pins = "gpio61";
 				function = "qup17";
 			};
 
-			qup_uart15_tx: qup-uart15-tx {
+			qup_uart15_tx: qup-uart15-tx-pins {
 				pins = "gpio62";
 				function = "qup17";
 			};
 
-			qup_uart15_rx: qup-uart15-rx {
+			qup_uart15_rx: qup-uart15-rx-pins {
 				pins = "gpio63";
 				function = "qup17";
 			};
+
+			sdc1_clk: sdc1-clk-pins {
+				pins = "sdc1_clk";
+			};
+
+			sdc1_cmd: sdc1-cmd-pins {
+				pins = "sdc1_cmd";
+			};
+
+			sdc1_data: sdc1-data-pins {
+				pins = "sdc1_data";
+			};
+
+			sdc1_rclk: sdc1-rclk-pins {
+				pins = "sdc1_rclk";
+			};
+
+			sdc1_clk_sleep: sdc1-clk-sleep-pins {
+				pins = "sdc1_clk";
+				drive-strength = <2>;
+				bias-bus-hold;
+			};
+
+			sdc1_cmd_sleep: sdc1-cmd-sleep-pins {
+				pins = "sdc1_cmd";
+				drive-strength = <2>;
+				bias-bus-hold;
+			};
+
+			sdc1_data_sleep: sdc1-data-sleep-pins {
+				pins = "sdc1_data";
+				drive-strength = <2>;
+				bias-bus-hold;
+			};
+
+			sdc1_rclk_sleep: sdc1-rclk-sleep-pins {
+				pins = "sdc1_rclk";
+				drive-strength = <2>;
+				bias-bus-hold;
+			};
+
+			sdc2_clk: sdc2-clk-pins {
+				pins = "sdc2_clk";
+			};
+
+			sdc2_cmd: sdc2-cmd-pins {
+				pins = "sdc2_cmd";
+			};
+
+			sdc2_data: sdc2-data-pins {
+				pins = "sdc2_data";
+			};
+
+			sdc2_clk_sleep: sdc2-clk-sleep-pins {
+				pins = "sdc2_clk";
+				drive-strength = <2>;
+				bias-bus-hold;
+			};
+
+			sdc2_cmd_sleep: sdc2-cmd-sleep-pins {
+				pins = "sdc2_cmd";
+				drive-strength = <2>;
+				bias-bus-hold;
+			};
+
+			sdc2_data_sleep: sdc2-data-sleep-pins {
+				pins = "sdc2_data";
+				drive-strength = <2>;
+				bias-bus-hold;
+			};
 		};
 
-		imem@146a5000 {
-			compatible = "qcom,sc7280-imem", "syscon";
+		sram@146a5000 {
+			compatible = "qcom,sc7280-imem", "syscon", "simple-mfd";
 			reg = <0 0x146a5000 0 0x6000>;
 
 			#address-cells = <1>;
@@ -3679,9 +5181,9 @@
 		};
 
 		timer@17c20000 {
-			#address-cells = <2>;
-			#size-cells = <2>;
-			ranges;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0 0 0x20000000>;
 			compatible = "arm,armv7-timer-mem";
 			reg = <0 0x17c20000 0 0x1000>;
 
@@ -3689,49 +5191,49 @@
 				frame-number = <0>;
 				interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
 					     <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0 0x17c21000 0 0x1000>,
-				      <0 0x17c22000 0 0x1000>;
+				reg = <0x17c21000 0x1000>,
+				      <0x17c22000 0x1000>;
 			};
 
 			frame@17c23000 {
 				frame-number = <1>;
 				interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0 0x17c23000 0 0x1000>;
+				reg = <0x17c23000 0x1000>;
 				status = "disabled";
 			};
 
 			frame@17c25000 {
 				frame-number = <2>;
 				interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0 0x17c25000 0 0x1000>;
+				reg = <0x17c25000 0x1000>;
 				status = "disabled";
 			};
 
 			frame@17c27000 {
 				frame-number = <3>;
 				interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0 0x17c27000 0 0x1000>;
+				reg = <0x17c27000 0x1000>;
 				status = "disabled";
 			};
 
 			frame@17c29000 {
 				frame-number = <4>;
 				interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0 0x17c29000 0 0x1000>;
+				reg = <0x17c29000 0x1000>;
 				status = "disabled";
 			};
 
 			frame@17c2b000 {
 				frame-number = <5>;
 				interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0 0x17c2b000 0 0x1000>;
+				reg = <0x17c2b000 0x1000>;
 				status = "disabled";
 			};
 
 			frame@17c2d000 {
 				frame-number = <6>;
 				interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0 0x17c2d000 0 0x1000>;
+				reg = <0x17c2d000 0x1000>;
 				status = "disabled";
 			};
 		};
@@ -3810,6 +5312,14 @@
 			};
 		};
 
+		epss_l3: interconnect@18590000 {
+			compatible = "qcom,sc7280-epss-l3";
+			reg = <0 0x18590000 0 0x1000>;
+			clocks = <&rpmhcc RPMH_CXO_CLK>, <&gcc GCC_GPLL0>;
+			clock-names = "xo", "alternate";
+			#interconnect-cells = <1>;
+		};
+
 		cpufreq_hw: cpufreq@18591000 {
 			compatible = "qcom,cpufreq-epss";
 			reg = <0 0x18591000 0 0x1000>,
diff --git a/arch/arm64/boot/dts/qcom/sc8280xp-crd.dts b/arch/arm64/boot/dts/qcom/sc8280xp-crd.dts
new file mode 100644
index 000000000000..fea7d8273ccd
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc8280xp-crd.dts
@@ -0,0 +1,434 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2022, Linaro Limited
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+
+#include "sc8280xp.dtsi"
+#include "sc8280xp-pmics.dtsi"
+
+/ {
+	model = "Qualcomm SC8280XP CRD";
+	compatible = "qcom,sc8280xp-crd", "qcom,sc8280xp";
+
+	aliases {
+		serial0 = &qup2_uart17;
+	};
+
+	backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pmc8280c_lpg 3 1000000>;
+		enable-gpios = <&pmc8280_1_gpios 8 GPIO_ACTIVE_HIGH>;
+		power-supply = <&vreg_edp_bl>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&edp_bl_en>, <&edp_bl_pwm>;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	vreg_edp_bl: regulator-edp-bl {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_EDP_BL";
+		regulator-min-microvolt = <3600000>;
+		regulator-max-microvolt = <3600000>;
+
+		gpio = <&pmc8280_1_gpios 9 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&edp_bl_reg_en>;
+
+		regulator-boot-on;
+	};
+
+	vreg_misc_3p3: regulator-misc-3p3 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_MISC_3P3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&pmc8280_1_gpios 1 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&misc_3p3_reg_en>;
+
+		regulator-boot-on;
+		regulator-always-on;
+	};
+};
+
+&apps_rsc {
+	pmc8280-1-rpmh-regulators {
+		compatible = "qcom,pm8350-rpmh-regulators";
+		qcom,pmic-id = "b";
+
+		vdd-l3-l5-supply = <&vreg_s11b>;
+
+		vreg_s11b: smps11 {
+			regulator-name = "vreg_s11b";
+			regulator-min-microvolt = <1272000>;
+			regulator-max-microvolt = <1272000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3b: ldo3 {
+			regulator-name = "vreg_l3b";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-boot-on;
+			regulator-always-on;
+		};
+
+		vreg_l4b: ldo4 {
+			regulator-name = "vreg_l4b";
+			regulator-min-microvolt = <912000>;
+			regulator-max-microvolt = <912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l6b: ldo6 {
+			regulator-name = "vreg_l6b";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <880000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-boot-on;
+		};
+	};
+
+	pmc8280c-rpmh-regulators {
+		compatible = "qcom,pm8350c-rpmh-regulators";
+		qcom,pmic-id = "c";
+
+		vreg_l1c: ldo1 {
+			regulator-name = "vreg_l1c";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l7c: ldo7 {
+			regulator-name = "vreg_l7c";
+			regulator-min-microvolt = <2504000>;
+			regulator-max-microvolt = <2504000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l13c: ldo13 {
+			regulator-name = "vreg_l13c";
+			regulator-min-microvolt = <3072000>;
+			regulator-max-microvolt = <3072000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	pmc8280-2-rpmh-regulators {
+		compatible = "qcom,pm8350-rpmh-regulators";
+		qcom,pmic-id = "d";
+
+		vdd-l1-l4-supply = <&vreg_s11b>;
+
+		vreg_l3d: ldo3 {
+			regulator-name = "vreg_l3d";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l4d: ldo4 {
+			regulator-name = "vreg_l4d";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l6d: ldo6 {
+			regulator-name = "vreg_l6d";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <880000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l7d: ldo7 {
+			regulator-name = "vreg_l7d";
+			regulator-min-microvolt = <3072000>;
+			regulator-max-microvolt = <3072000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l9d: ldo9 {
+			regulator-name = "vreg_l9d";
+			regulator-min-microvolt = <912000>;
+			regulator-max-microvolt = <912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+};
+
+&pmc8280c_lpg {
+	status = "okay";
+};
+
+&pmk8280_pon_pwrkey {
+	status = "okay";
+};
+
+&qup0 {
+	status = "okay";
+};
+
+&qup0_i2c4 {
+	clock-frequency = <400000>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&qup0_i2c4_default>;
+
+	status = "okay";
+
+	touchscreen@10 {
+		compatible = "hid-over-i2c";
+		reg = <0x10>;
+
+		hid-descr-addr = <0x1>;
+		interrupts-extended = <&tlmm 175 IRQ_TYPE_LEVEL_LOW>;
+		vdd-supply = <&vreg_misc_3p3>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&ts0_default>;
+	};
+};
+
+&qup1 {
+	status = "okay";
+};
+
+&qup2 {
+	status = "okay";
+};
+
+&qup2_i2c5 {
+	clock-frequency = <400000>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&qup2_i2c5_default>;
+
+	status = "okay";
+
+	touchpad@15 {
+		compatible = "hid-over-i2c";
+		reg = <0x15>;
+
+		hid-descr-addr = <0x1>;
+		interrupts-extended = <&tlmm 182 IRQ_TYPE_LEVEL_LOW>;
+		vdd-supply = <&vreg_misc_3p3>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&tpad_default>;
+
+		wakeup-source;
+	};
+
+	keyboard@68 {
+		compatible = "hid-over-i2c";
+		reg = <0x68>;
+
+		hid-descr-addr = <0x1>;
+		interrupts-extended = <&tlmm 104 IRQ_TYPE_LEVEL_LOW>;
+		vdd-supply = <&vreg_misc_3p3>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&kybd_default>;
+
+		wakeup-source;
+	};
+};
+
+&qup2_uart17 {
+	compatible = "qcom,geni-debug-uart";
+
+	status = "okay";
+};
+
+&remoteproc_adsp {
+	firmware-name = "qcom/sc8280xp/qcadsp8280.mbn";
+
+	status = "okay";
+};
+
+&remoteproc_nsp0 {
+	firmware-name = "qcom/sc8280xp/qccdsp8280.mbn";
+
+	status = "okay";
+};
+
+&ufs_mem_hc {
+	reset-gpios = <&tlmm 228 GPIO_ACTIVE_LOW>;
+
+	vcc-supply = <&vreg_l7c>;
+	vcc-max-microamp = <800000>;
+	vccq-supply = <&vreg_l3d>;
+	vccq-max-microamp = <900000>;
+
+	status = "okay";
+};
+
+&ufs_mem_phy {
+	vdda-phy-supply = <&vreg_l6b>;
+	vdda-pll-supply = <&vreg_l3b>;
+
+	status = "okay";
+};
+
+&usb_0 {
+	status = "okay";
+};
+
+&usb_0_dwc3 {
+	/* TODO: Define USB-C connector properly */
+	dr_mode = "host";
+};
+
+&usb_0_hsphy {
+	vdda-pll-supply = <&vreg_l9d>;
+	vdda18-supply = <&vreg_l1c>;
+	vdda33-supply = <&vreg_l7d>;
+
+	status = "okay";
+};
+
+&usb_0_qmpphy {
+	vdda-phy-supply = <&vreg_l9d>;
+	vdda-pll-supply = <&vreg_l4d>;
+
+	status = "okay";
+};
+
+&usb_1 {
+	status = "okay";
+};
+
+&usb_1_dwc3 {
+	/* TODO: Define USB-C connector properly */
+	dr_mode = "host";
+};
+
+&usb_1_hsphy {
+	vdda-pll-supply = <&vreg_l4b>;
+	vdda18-supply = <&vreg_l1c>;
+	vdda33-supply = <&vreg_l13c>;
+
+	status = "okay";
+};
+
+&usb_1_qmpphy {
+	vdda-phy-supply = <&vreg_l4b>;
+	vdda-pll-supply = <&vreg_l3b>;
+
+	status = "okay";
+};
+
+&xo_board_clk {
+	clock-frequency = <38400000>;
+};
+
+/* PINCTRL - additions to nodes defined in sc8280xp.dtsi */
+
+&pmc8280_1_gpios {
+	edp_bl_en: edp-bl-en-state {
+		pins = "gpio8";
+		function = "normal";
+	};
+
+	edp_bl_reg_en: edp-bl-reg-en-state {
+		pins = "gpio9";
+		function = "normal";
+	};
+
+	misc_3p3_reg_en: misc-3p3-reg-en-state {
+		pins = "gpio1";
+		function = "normal";
+	};
+};
+
+&pmc8280c_gpios {
+	edp_bl_pwm: edp-bl-pwm-state {
+		pins = "gpio8";
+		function = "func1";
+	};
+};
+
+&tlmm {
+	gpio-reserved-ranges = <74 6>, <83 4>, <125 2>, <128 2>, <154 7>;
+
+	kybd_default: kybd-default-state {
+		disable {
+			pins = "gpio102";
+			function = "gpio";
+			output-low;
+		};
+
+		int-n {
+			pins = "gpio104";
+			function = "gpio";
+			bias-disable;
+		};
+
+		reset {
+			pins = "gpio105";
+			function = "gpio";
+			bias-disable;
+		};
+	};
+
+	qup0_i2c4_default: qup0-i2c4-default-state {
+		pins = "gpio171", "gpio172";
+		function = "qup4";
+
+		bias-disable;
+		drive-strength = <16>;
+	};
+
+	qup2_i2c5_default: qup2-i2c5-default-state {
+		pins = "gpio81", "gpio82";
+		function = "qup21";
+
+		bias-disable;
+		drive-strength = <16>;
+	};
+
+	tpad_default: tpad-default-state {
+		int-n {
+			pins = "gpio182";
+			function = "gpio";
+			bias-disable;
+		};
+	};
+
+	ts0_default: ts0-default-state {
+		int-n {
+			pins = "gpio175";
+			function = "gpio";
+			bias-disable;
+		};
+
+		reset-n {
+			pins = "gpio99";
+			function = "gpio";
+			output-high;
+			drive-strength = <16>;
+		};
+	};
+};
diff --git a/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts b/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts
new file mode 100644
index 000000000000..b2b744bb8a53
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc8280xp-lenovo-thinkpad-x13s.dts
@@ -0,0 +1,408 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2022, Linaro Limited
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+
+#include "sc8280xp.dtsi"
+#include "sc8280xp-pmics.dtsi"
+
+/ {
+	model = "Lenovo ThinkPad X13s";
+	compatible = "lenovo,thinkpad-x13s", "qcom,sc8280xp";
+
+	backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pmc8280c_lpg 3 1000000>;
+		enable-gpios = <&pmc8280_1_gpios 8 GPIO_ACTIVE_HIGH>;
+		power-supply = <&vreg_edp_bl>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&edp_bl_en>, <&edp_bl_pwm>;
+	};
+
+	vreg_edp_bl: regulator-edp-bl {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VBL9";
+		regulator-min-microvolt = <3600000>;
+		regulator-max-microvolt = <3600000>;
+
+		gpio = <&pmc8280_1_gpios 9 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&edp_bl_reg_en>;
+
+		regulator-boot-on;
+	};
+
+	vreg_misc_3p3: regulator-misc-3p3 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VCC3B";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&pmc8280_1_gpios 1 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&misc_3p3_reg_en>;
+
+		regulator-boot-on;
+		regulator-always-on;
+	};
+};
+
+&apps_rsc {
+	pmc8280-1-rpmh-regulators {
+		compatible = "qcom,pm8350-rpmh-regulators";
+		qcom,pmic-id = "b";
+
+		vdd-l3-l5-supply = <&vreg_s11b>;
+
+		vreg_s11b: smps11 {
+			regulator-name = "vreg_s11b";
+			regulator-min-microvolt = <1272000>;
+			regulator-max-microvolt = <1272000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3b: ldo3 {
+			regulator-name = "vreg_l3b";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-boot-on;
+		};
+
+		vreg_l4b: ldo4 {
+			regulator-name = "vreg_l4b";
+			regulator-min-microvolt = <912000>;
+			regulator-max-microvolt = <912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l6b: ldo6 {
+			regulator-name = "vreg_l6b";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <880000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-boot-on;
+			regulator-always-on;	// FIXME: VDD_A_EDP_0_0P9
+		};
+	};
+
+	pmc8280c-rpmh-regulators {
+		compatible = "qcom,pm8350c-rpmh-regulators";
+		qcom,pmic-id = "c";
+
+		vreg_l1c: ldo1 {
+			regulator-name = "vreg_l1c";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l12c: ldo12 {
+			regulator-name = "vreg_l12c";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l13c: ldo13 {
+			regulator-name = "vreg_l13c";
+			regulator-min-microvolt = <3072000>;
+			regulator-max-microvolt = <3072000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	pmc8280-2-rpmh-regulators {
+		compatible = "qcom,pm8350-rpmh-regulators";
+		qcom,pmic-id = "d";
+
+		vdd-l1-l4-supply = <&vreg_s11b>;
+
+		vreg_l3d: ldo3 {
+			regulator-name = "vreg_l3d";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l4d: ldo4 {
+			regulator-name = "vreg_l4d";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l7d: ldo7 {
+			regulator-name = "vreg_l7d";
+			regulator-min-microvolt = <3072000>;
+			regulator-max-microvolt = <3072000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l9d: ldo9 {
+			regulator-name = "vreg_l9d";
+			regulator-min-microvolt = <912000>;
+			regulator-max-microvolt = <912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+};
+
+&pmc8280c_lpg {
+	status = "okay";
+};
+
+&pmk8280_pon_pwrkey {
+	status = "okay";
+};
+
+&qup0 {
+	status = "okay";
+};
+
+&qup0_i2c4 {
+	clock-frequency = <400000>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&qup0_i2c4_default>;
+
+	status = "okay";
+
+	/* FIXME: verify */
+	touchscreen@10 {
+		compatible = "hid-over-i2c";
+		reg = <0x10>;
+
+		hid-descr-addr = <0x1>;
+		interrupts-extended = <&tlmm 175 IRQ_TYPE_LEVEL_LOW>;
+		vdd-supply = <&vreg_misc_3p3>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&ts0_default>;
+	};
+};
+
+&qup1 {
+	status = "okay";
+};
+
+&qup2 {
+	status = "okay";
+};
+
+&qup2_i2c5 {
+	clock-frequency = <400000>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&qup2_i2c5_default>;
+
+	status = "okay";
+
+	touchpad@15 {
+		compatible = "hid-over-i2c";
+		reg = <0x15>;
+
+		hid-descr-addr = <0x1>;
+		interrupts-extended = <&tlmm 182 IRQ_TYPE_LEVEL_LOW>;
+		vdd-supply = <&vreg_misc_3p3>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&tpad_default>;
+
+		wakeup-source;
+
+		status = "disabled";
+	};
+
+	touchpad@2c {
+		compatible = "hid-over-i2c";
+		reg = <0x2c>;
+
+		hid-descr-addr = <0x20>;
+		interrupts-extended = <&tlmm 182 IRQ_TYPE_LEVEL_LOW>;
+		vdd-supply = <&vreg_misc_3p3>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&tpad_default>;
+
+		wakeup-source;
+	};
+
+	keyboard@68 {
+		compatible = "hid-over-i2c";
+		reg = <0x68>;
+
+		hid-descr-addr = <0x1>;
+		interrupts-extended = <&tlmm 104 IRQ_TYPE_LEVEL_LOW>;
+		vdd-supply = <&vreg_misc_3p3>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&kybd_default>;
+
+		wakeup-source;
+	};
+};
+
+&remoteproc_adsp {
+	firmware-name = "qcom/sc8280xp/LENOVO/21BX/qcadsp8280.mbn";
+
+	status = "okay";
+};
+
+&remoteproc_nsp0 {
+	firmware-name = "qcom/sc8280xp/LENOVO/21BX/qccdsp8280.mbn";
+
+	status = "okay";
+};
+
+&usb_0 {
+	status = "okay";
+};
+
+&usb_0_dwc3 {
+	/* TODO: Define USB-C connector properly */
+	dr_mode = "host";
+};
+
+&usb_0_hsphy {
+	vdda-pll-supply = <&vreg_l9d>;
+	vdda18-supply = <&vreg_l1c>;
+	vdda33-supply = <&vreg_l7d>;
+
+	status = "okay";
+};
+
+&usb_0_qmpphy {
+	vdda-phy-supply = <&vreg_l9d>;
+	vdda-pll-supply = <&vreg_l4d>;
+
+	status = "okay";
+};
+
+&usb_1 {
+	status = "okay";
+};
+
+&usb_1_dwc3 {
+	/* TODO: Define USB-C connector properly */
+	dr_mode = "host";
+};
+
+&usb_1_hsphy {
+	vdda-pll-supply = <&vreg_l4b>;
+	vdda18-supply = <&vreg_l1c>;
+	vdda33-supply = <&vreg_l13c>;
+
+	status = "okay";
+};
+
+&usb_1_qmpphy {
+	vdda-phy-supply = <&vreg_l4b>;
+	vdda-pll-supply = <&vreg_l3b>;
+
+	status = "okay";
+};
+
+&xo_board_clk {
+	clock-frequency = <38400000>;
+};
+
+/* PINCTRL */
+
+&pmc8280_1_gpios {
+	edp_bl_en: edp-bl-en-state {
+		pins = "gpio8";
+		function = "normal";
+	};
+
+	edp_bl_reg_en: edp-bl-reg-en-state {
+		pins = "gpio9";
+		function = "normal";
+	};
+
+	misc_3p3_reg_en: misc-3p3-reg-en-state {
+		pins = "gpio1";
+		function = "normal";
+	};
+};
+
+&pmc8280c_gpios {
+	edp_bl_pwm: edp-bl-pwm-state {
+		pins = "gpio8";
+		function = "func1";
+	};
+};
+
+&tlmm {
+	gpio-reserved-ranges = <70 2>, <74 6>, <83 4>, <125 2>, <128 2>, <154 7>;
+
+	kybd_default: kybd-default-state {
+		disable {
+			pins = "gpio102";
+			function = "gpio";
+			output-low;
+		};
+
+		int-n {
+			pins = "gpio104";
+			function = "gpio";
+			bias-disable;
+		};
+
+		reset {
+			pins = "gpio105";
+			function = "gpio";
+			bias-disable;
+		};
+	};
+
+	qup0_i2c4_default: qup0-i2c4-default-state {
+		pins = "gpio171", "gpio172";
+		function = "qup4";
+		bias-disable;
+		drive-strength = <16>;
+	};
+
+	qup2_i2c5_default: qup2-i2c5-default-state {
+		pins = "gpio81", "gpio82";
+		function = "qup21";
+		bias-disable;
+		drive-strength = <16>;
+	};
+
+	tpad_default: tpad-default-state {
+		int-n {
+			pins = "gpio182";
+			function = "gpio";
+			bias-disable;
+		};
+	};
+
+	ts0_default: ts0-default-state {
+		int-n {
+			pins = "gpio175";
+			function = "gpio";
+			bias-disable;
+		};
+
+		reset-n {
+			pins = "gpio99";
+			function = "gpio";
+			output-high;
+			drive-strength = <16>;
+		};
+	};
+};
diff --git a/arch/arm64/boot/dts/qcom/sc8280xp-pmics.dtsi b/arch/arm64/boot/dts/qcom/sc8280xp-pmics.dtsi
new file mode 100644
index 000000000000..24836b6b9bbc
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc8280xp-pmics.dtsi
@@ -0,0 +1,108 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2022, Linaro Limited
+ */
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/spmi/spmi.h>
+
+&spmi_bus {
+	pmk8280: pmic@0 {
+		compatible = "qcom,pmk8350", "qcom,spmi-pmic";
+		reg = <0x0 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pmk8280_pon: pon@1300 {
+			compatible = "qcom,pm8998-pon";
+			reg = <0x1300>;
+
+			pmk8280_pon_pwrkey: pwrkey {
+				compatible = "qcom,pmk8350-pwrkey";
+				interrupts = <0x0 0x13 0x7 IRQ_TYPE_EDGE_BOTH>;
+				linux,code = <KEY_POWER>;
+				status = "disabled";
+			};
+		};
+	};
+
+	pmc8280_1: pmic@1 {
+		compatible = "qcom,pm8350", "qcom,spmi-pmic";
+		reg = <0x1 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pmc8280_1_gpios: gpio@8800 {
+			compatible = "qcom,pm8350-gpio", "qcom,spmi-gpio";
+			reg = <0x8800>;
+			gpio-controller;
+			gpio-ranges = <&pmc8280_1_gpios 0 0 10>;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	pmc8280c: pmic@2 {
+		compatible = "qcom,pm8350c", "qcom,spmi-pmic";
+		reg = <0x2 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pmc8280c_gpios: gpio@8800 {
+			compatible = "qcom,pm8350c-gpio", "qcom,spmi-gpio";
+			reg = <0x8800>;
+			gpio-controller;
+			gpio-ranges = <&pmc8280c_gpios 0 0 9>;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		pmc8280c_lpg: pwm {
+			compatible = "qcom,pm8350c-pwm";
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			#pwm-cells = <2>;
+
+			status = "disabled";
+		};
+	};
+
+	pmc8280_2: pmic@3 {
+		compatible = "qcom,pm8350", "qcom,spmi-pmic";
+		reg = <0x3 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pmc8280_2_gpios: gpio@8800 {
+			compatible = "qcom,pm8350-gpio", "qcom,spmi-gpio";
+			reg = <0x8800>;
+			gpio-controller;
+			gpio-ranges = <&pmc8280_2_gpios 0 0 10>;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	pmr735a: pmic@4 {
+		compatible = "qcom,pmr735a", "qcom,spmi-pmic";
+		reg = <0x4 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pmr735a_gpios: gpio@8800 {
+			compatible = "qcom,pmr735a-gpio", "qcom,spmi-gpio";
+			reg = <0x8800>;
+			gpio-controller;
+			gpio-ranges = <&pmr735a_gpios 0 0 4>;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+};
diff --git a/arch/arm64/boot/dts/qcom/sc8280xp.dtsi b/arch/arm64/boot/dts/qcom/sc8280xp.dtsi
new file mode 100644
index 000000000000..c32bcded2aef
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc8280xp.dtsi
@@ -0,0 +1,2151 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2022, Linaro Limited
+ */
+
+#include <dt-bindings/clock/qcom,gcc-sc8280xp.h>
+#include <dt-bindings/clock/qcom,rpmh.h>
+#include <dt-bindings/interconnect/qcom,sc8280xp.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/mailbox/qcom-ipcc.h>
+#include <dt-bindings/power/qcom-rpmpd.h>
+#include <dt-bindings/soc/qcom,rpmh-rsc.h>
+#include <dt-bindings/thermal/thermal.h>
+
+/ {
+	interrupt-parent = <&intc>;
+
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	clocks {
+		xo_board_clk: xo-board-clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+		};
+
+		sleep_clk: sleep-clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <32764>;
+		};
+	};
+
+	cpu0_opp_table: cpu0-opp-table {
+		compatible = "operating-points-v2";
+		opp-shared;
+
+		opp-300000000 {
+			opp-hz = /bits/ 64 <300000000>;
+		};
+		opp-403200000 {
+			opp-hz = /bits/ 64 <403200000>;
+		};
+		opp-499200000 {
+			opp-hz = /bits/ 64 <499200000>;
+		};
+		opp-595200000 {
+			opp-hz = /bits/ 64 <595200000>;
+		};
+		opp-691200000 {
+			opp-hz = /bits/ 64 <691200000>;
+		};
+		opp-806400000 {
+			opp-hz = /bits/ 64 <806400000>;
+		};
+		opp-902400000 {
+			opp-hz = /bits/ 64 <902400000>;
+		};
+		opp-1017600000 {
+			opp-hz = /bits/ 64 <1017600000>;
+		};
+		opp-1113600000 {
+			opp-hz = /bits/ 64 <1113600000>;
+		};
+		opp-1209600000 {
+			opp-hz = /bits/ 64 <1209600000>;
+		};
+		opp-1324800000 {
+			opp-hz = /bits/ 64 <1324800000>;
+		};
+		opp-1440000000 {
+			opp-hz = /bits/ 64 <1440000000>;
+		};
+		opp-1555200000 {
+			opp-hz = /bits/ 64 <1555200000>;
+		};
+		opp-1670400000 {
+			opp-hz = /bits/ 64 <1670400000>;
+		};
+		opp-1785600000 {
+			opp-hz = /bits/ 64 <1785600000>;
+		};
+		opp-1881600000 {
+			opp-hz = /bits/ 64 <1881600000>;
+		};
+		opp-1996800000 {
+			opp-hz = /bits/ 64 <1996800000>;
+		};
+		opp-2112000000 {
+			opp-hz = /bits/ 64 <2112000000>;
+		};
+		opp-2227200000 {
+			opp-hz = /bits/ 64 <2227200000>;
+		};
+		opp-2342400000 {
+			opp-hz = /bits/ 64 <2342400000>;
+		};
+		opp-2438400000 {
+			opp-hz = /bits/ 64 <2438400000>;
+		};
+	};
+
+	cpu4_opp_table: cpu4-opp-table {
+		compatible = "operating-points-v2";
+		opp-shared;
+
+		opp-825600000 {
+			opp-hz = /bits/ 64 <825600000>;
+		};
+		opp-940800000 {
+			opp-hz = /bits/ 64 <940800000>;
+		};
+		opp-1056000000 {
+			opp-hz = /bits/ 64 <1056000000>;
+		};
+		opp-1171200000 {
+			opp-hz = /bits/ 64 <1171200000>;
+		};
+		opp-1286400000 {
+			opp-hz = /bits/ 64 <1286400000>;
+		};
+		opp-1401600000 {
+			opp-hz = /bits/ 64 <1401600000>;
+		};
+		opp-1516800000 {
+			opp-hz = /bits/ 64 <1516800000>;
+		};
+		opp-1632000000 {
+			opp-hz = /bits/ 64 <1632000000>;
+		};
+		opp-1747200000 {
+			opp-hz = /bits/ 64 <1747200000>;
+		};
+		opp-1862400000 {
+			opp-hz = /bits/ 64 <1862400000>;
+		};
+		opp-1977600000 {
+			opp-hz = /bits/ 64 <1977600000>;
+		};
+		opp-2073600000 {
+			opp-hz = /bits/ 64 <2073600000>;
+		};
+		opp-2169600000 {
+			opp-hz = /bits/ 64 <2169600000>;
+		};
+		opp-2284800000 {
+			opp-hz = /bits/ 64 <2284800000>;
+		};
+		opp-2400000000 {
+			opp-hz = /bits/ 64 <2400000000>;
+		};
+		opp-2496000000 {
+			opp-hz = /bits/ 64 <2496000000>;
+		};
+		opp-2592000000 {
+			opp-hz = /bits/ 64 <2592000000>;
+		};
+		opp-2688000000 {
+			opp-hz = /bits/ 64 <2688000000>;
+		};
+		opp-2803200000 {
+			opp-hz = /bits/ 64 <2803200000>;
+		};
+		opp-2899200000 {
+			opp-hz = /bits/ 64 <2899200000>;
+		};
+		opp-2995200000 {
+			opp-hz = /bits/ 64 <2995200000>;
+		};
+	};
+
+	cpus {
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		CPU0: cpu@0 {
+			device_type = "cpu";
+			compatible = "qcom,kryo";
+			reg = <0x0 0x0>;
+			enable-method = "psci";
+			capacity-dmips-mhz = <602>;
+			next-level-cache = <&L2_0>;
+			power-domains = <&CPU_PD0>;
+			power-domain-names = "psci";
+			qcom,freq-domain = <&cpufreq_hw 0>;
+			operating-points-v2 = <&cpu0_opp_table>;
+			#cooling-cells = <2>;
+			L2_0: l2-cache {
+				compatible = "cache";
+				next-level-cache = <&L3_0>;
+				L3_0: l3-cache {
+				      compatible = "cache";
+				};
+			};
+		};
+
+		CPU1: cpu@100 {
+			device_type = "cpu";
+			compatible = "qcom,kryo";
+			reg = <0x0 0x100>;
+			enable-method = "psci";
+			capacity-dmips-mhz = <602>;
+			next-level-cache = <&L2_100>;
+			power-domains = <&CPU_PD1>;
+			power-domain-names = "psci";
+			qcom,freq-domain = <&cpufreq_hw 0>;
+			operating-points-v2 = <&cpu0_opp_table>;
+			#cooling-cells = <2>;
+			L2_100: l2-cache {
+				compatible = "cache";
+				next-level-cache = <&L3_0>;
+			};
+		};
+
+		CPU2: cpu@200 {
+			device_type = "cpu";
+			compatible = "qcom,kryo";
+			reg = <0x0 0x200>;
+			enable-method = "psci";
+			capacity-dmips-mhz = <602>;
+			next-level-cache = <&L2_200>;
+			power-domains = <&CPU_PD2>;
+			power-domain-names = "psci";
+			qcom,freq-domain = <&cpufreq_hw 0>;
+			operating-points-v2 = <&cpu0_opp_table>;
+			#cooling-cells = <2>;
+			L2_200: l2-cache {
+				compatible = "cache";
+				next-level-cache = <&L3_0>;
+			};
+		};
+
+		CPU3: cpu@300 {
+			device_type = "cpu";
+			compatible = "qcom,kryo";
+			reg = <0x0 0x300>;
+			enable-method = "psci";
+			capacity-dmips-mhz = <602>;
+			next-level-cache = <&L2_300>;
+			power-domains = <&CPU_PD3>;
+			power-domain-names = "psci";
+			qcom,freq-domain = <&cpufreq_hw 0>;
+			operating-points-v2 = <&cpu0_opp_table>;
+			#cooling-cells = <2>;
+			L2_300: l2-cache {
+				compatible = "cache";
+				next-level-cache = <&L3_0>;
+			};
+		};
+
+		CPU4: cpu@400 {
+			device_type = "cpu";
+			compatible = "qcom,kryo";
+			reg = <0x0 0x400>;
+			enable-method = "psci";
+			capacity-dmips-mhz = <1024>;
+			next-level-cache = <&L2_400>;
+			power-domains = <&CPU_PD4>;
+			power-domain-names = "psci";
+			qcom,freq-domain = <&cpufreq_hw 1>;
+			operating-points-v2 = <&cpu4_opp_table>;
+			#cooling-cells = <2>;
+			L2_400: l2-cache {
+				compatible = "cache";
+				next-level-cache = <&L3_0>;
+			};
+		};
+
+		CPU5: cpu@500 {
+			device_type = "cpu";
+			compatible = "qcom,kryo";
+			reg = <0x0 0x500>;
+			enable-method = "psci";
+			capacity-dmips-mhz = <1024>;
+			next-level-cache = <&L2_500>;
+			power-domains = <&CPU_PD5>;
+			power-domain-names = "psci";
+			qcom,freq-domain = <&cpufreq_hw 1>;
+			operating-points-v2 = <&cpu4_opp_table>;
+			#cooling-cells = <2>;
+			L2_500: l2-cache {
+				compatible = "cache";
+				next-level-cache = <&L3_0>;
+			};
+		};
+
+		CPU6: cpu@600 {
+			device_type = "cpu";
+			compatible = "qcom,kryo";
+			reg = <0x0 0x600>;
+			enable-method = "psci";
+			capacity-dmips-mhz = <1024>;
+			next-level-cache = <&L2_600>;
+			power-domains = <&CPU_PD6>;
+			power-domain-names = "psci";
+			qcom,freq-domain = <&cpufreq_hw 1>;
+			operating-points-v2 = <&cpu4_opp_table>;
+			#cooling-cells = <2>;
+			L2_600: l2-cache {
+				compatible = "cache";
+				next-level-cache = <&L3_0>;
+			};
+		};
+
+		CPU7: cpu@700 {
+			device_type = "cpu";
+			compatible = "qcom,kryo";
+			reg = <0x0 0x700>;
+			enable-method = "psci";
+			capacity-dmips-mhz = <1024>;
+			next-level-cache = <&L2_700>;
+			power-domains = <&CPU_PD7>;
+			power-domain-names = "psci";
+			qcom,freq-domain = <&cpufreq_hw 1>;
+			operating-points-v2 = <&cpu4_opp_table>;
+			#cooling-cells = <2>;
+			L2_700: l2-cache {
+				compatible = "cache";
+				next-level-cache = <&L3_0>;
+			};
+		};
+
+		cpu-map {
+			cluster0 {
+				core0 {
+					cpu = <&CPU0>;
+				};
+
+				core1 {
+					cpu = <&CPU1>;
+				};
+
+				core2 {
+					cpu = <&CPU2>;
+				};
+
+				core3 {
+					cpu = <&CPU3>;
+				};
+
+				core4 {
+					cpu = <&CPU4>;
+				};
+
+				core5 {
+					cpu = <&CPU5>;
+				};
+
+				core6 {
+					cpu = <&CPU6>;
+				};
+
+				core7 {
+					cpu = <&CPU7>;
+				};
+			};
+		};
+
+		idle-states {
+			entry-method = "psci";
+
+			LITTLE_CPU_SLEEP_0: cpu-sleep-0-0 {
+				compatible = "arm,idle-state";
+				idle-state-name = "little-rail-power-collapse";
+				arm,psci-suspend-param = <0x40000004>;
+				entry-latency-us = <355>;
+				exit-latency-us = <909>;
+				min-residency-us = <3934>;
+				local-timer-stop;
+			};
+
+			BIG_CPU_SLEEP_0: cpu-sleep-1-0 {
+				compatible = "arm,idle-state";
+				idle-state-name = "big-rail-power-collapse";
+				arm,psci-suspend-param = <0x40000004>;
+				entry-latency-us = <241>;
+				exit-latency-us = <1461>;
+				min-residency-us = <4488>;
+				local-timer-stop;
+			};
+		};
+
+		domain-idle-states {
+			CLUSTER_SLEEP_0: cluster-sleep-0 {
+				compatible = "domain-idle-state";
+				idle-state-name = "cluster-power-collapse";
+				arm,psci-suspend-param = <0x4100c344>;
+				entry-latency-us = <3263>;
+				exit-latency-us = <6562>;
+				min-residency-us = <9987>;
+			};
+		};
+	};
+
+	firmware {
+		scm: scm {
+			compatible = "qcom,scm-sc8280xp", "qcom,scm";
+		};
+	};
+
+	aggre1_noc: interconnect-aggre1-noc {
+		compatible = "qcom,sc8280xp-aggre1-noc";
+		#interconnect-cells = <2>;
+		qcom,bcm-voters = <&apps_bcm_voter>;
+	};
+
+	aggre2_noc: interconnect-aggre2-noc {
+		compatible = "qcom,sc8280xp-aggre2-noc";
+		#interconnect-cells = <2>;
+		qcom,bcm-voters = <&apps_bcm_voter>;
+	};
+
+	clk_virt: interconnect-clk-virt {
+		compatible = "qcom,sc8280xp-clk-virt";
+		#interconnect-cells = <2>;
+		qcom,bcm-voters = <&apps_bcm_voter>;
+	};
+
+	config_noc: interconnect-config-noc {
+		compatible = "qcom,sc8280xp-config-noc";
+		#interconnect-cells = <2>;
+		qcom,bcm-voters = <&apps_bcm_voter>;
+	};
+
+	dc_noc: interconnect-dc-noc {
+		compatible = "qcom,sc8280xp-dc-noc";
+		#interconnect-cells = <2>;
+		qcom,bcm-voters = <&apps_bcm_voter>;
+	};
+
+	gem_noc: interconnect-gem-noc {
+		compatible = "qcom,sc8280xp-gem-noc";
+		#interconnect-cells = <2>;
+		qcom,bcm-voters = <&apps_bcm_voter>;
+	};
+
+	lpass_noc: interconnect-lpass-ag-noc {
+		compatible = "qcom,sc8280xp-lpass-ag-noc";
+		#interconnect-cells = <2>;
+		qcom,bcm-voters = <&apps_bcm_voter>;
+	};
+
+	mc_virt: interconnect-mc-virt {
+		compatible = "qcom,sc8280xp-mc-virt";
+		#interconnect-cells = <2>;
+		qcom,bcm-voters = <&apps_bcm_voter>;
+	};
+
+	mmss_noc: interconnect-mmss-noc {
+		compatible = "qcom,sc8280xp-mmss-noc";
+		#interconnect-cells = <2>;
+		qcom,bcm-voters = <&apps_bcm_voter>;
+	};
+
+	nspa_noc: interconnect-nspa-noc {
+		compatible = "qcom,sc8280xp-nspa-noc";
+		#interconnect-cells = <2>;
+		qcom,bcm-voters = <&apps_bcm_voter>;
+	};
+
+	nspb_noc: interconnect-nspb-noc {
+		compatible = "qcom,sc8280xp-nspb-noc";
+		#interconnect-cells = <2>;
+		qcom,bcm-voters = <&apps_bcm_voter>;
+	};
+
+	system_noc: interconnect-system-noc {
+		compatible = "qcom,sc8280xp-system-noc";
+		#interconnect-cells = <2>;
+		qcom,bcm-voters = <&apps_bcm_voter>;
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		/* We expect the bootloader to fill in the size */
+		reg = <0x0 0x80000000 0x0 0x0>;
+	};
+
+	pmu {
+		compatible = "arm,armv8-pmuv3";
+		interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
+	psci {
+		compatible = "arm,psci-1.0";
+		method = "smc";
+
+		CPU_PD0: cpu0 {
+			#power-domain-cells = <0>;
+			power-domains = <&CLUSTER_PD>;
+			domain-idle-states = <&LITTLE_CPU_SLEEP_0>;
+		};
+
+		CPU_PD1: cpu1 {
+			#power-domain-cells = <0>;
+			power-domains = <&CLUSTER_PD>;
+			domain-idle-states = <&LITTLE_CPU_SLEEP_0>;
+		};
+
+		CPU_PD2: cpu2 {
+			#power-domain-cells = <0>;
+			power-domains = <&CLUSTER_PD>;
+			domain-idle-states = <&LITTLE_CPU_SLEEP_0>;
+		};
+
+		CPU_PD3: cpu3 {
+			#power-domain-cells = <0>;
+			power-domains = <&CLUSTER_PD>;
+			domain-idle-states = <&LITTLE_CPU_SLEEP_0>;
+		};
+
+		CPU_PD4: cpu4 {
+			#power-domain-cells = <0>;
+			power-domains = <&CLUSTER_PD>;
+			domain-idle-states = <&BIG_CPU_SLEEP_0>;
+		};
+
+		CPU_PD5: cpu5 {
+			#power-domain-cells = <0>;
+			power-domains = <&CLUSTER_PD>;
+			domain-idle-states = <&BIG_CPU_SLEEP_0>;
+		};
+
+		CPU_PD6: cpu6 {
+			#power-domain-cells = <0>;
+			power-domains = <&CLUSTER_PD>;
+			domain-idle-states = <&BIG_CPU_SLEEP_0>;
+		};
+
+		CPU_PD7: cpu7 {
+			#power-domain-cells = <0>;
+			power-domains = <&CLUSTER_PD>;
+			domain-idle-states = <&BIG_CPU_SLEEP_0>;
+		};
+
+		CLUSTER_PD: cpu-cluster0 {
+			#power-domain-cells = <0>;
+			domain-idle-states = <&CLUSTER_SLEEP_0>;
+		};
+	};
+
+	qup_opp_table_100mhz: qup-100mhz-opp-table {
+		compatible = "operating-points-v2";
+
+		opp-75000000 {
+			opp-hz = /bits/ 64 <75000000>;
+			required-opps = <&rpmhpd_opp_low_svs>;
+		};
+
+		opp-100000000 {
+			opp-hz = /bits/ 64 <100000000>;
+			required-opps = <&rpmhpd_opp_svs>;
+		};
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		reserved-region@80000000 {
+			reg = <0 0x80000000 0 0x860000>;
+			no-map;
+		};
+
+		cmd_db: cmd-db-region@80860000 {
+			compatible = "qcom,cmd-db";
+			reg = <0 0x80860000 0 0x20000>;
+			no-map;
+		};
+
+		reserved-region@80880000 {
+			reg = <0 0x80880000 0 0x80000>;
+			no-map;
+		};
+
+		smem_mem: smem-region@80900000 {
+			compatible = "qcom,smem";
+			reg = <0 0x80900000 0 0x200000>;
+			no-map;
+			hwlocks = <&tcsr_mutex 3>;
+		};
+
+		reserved-region@80b00000 {
+			reg = <0 0x80b00000 0 0x100000>;
+			no-map;
+		};
+
+		reserved-region@83b00000 {
+			reg = <0 0x83b00000 0 0x1700000>;
+			no-map;
+		};
+
+		reserved-region@85b00000 {
+			reg = <0 0x85b00000 0 0xc00000>;
+			no-map;
+		};
+
+		pil_adsp_mem: adsp-region@86c00000 {
+			reg = <0 0x86c00000 0 0x2000000>;
+			no-map;
+		};
+
+		pil_nsp0_mem: cdsp0-region@8a100000 {
+			reg = <0 0x8a100000 0 0x1e00000>;
+			no-map;
+		};
+
+		pil_nsp1_mem: cdsp1-region@8c600000 {
+			reg = <0 0x8c600000 0 0x1e00000>;
+			no-map;
+		};
+
+		reserved-region@aeb00000 {
+			reg = <0 0xaeb00000 0 0x16600000>;
+			no-map;
+		};
+	};
+
+	smp2p-adsp {
+		compatible = "qcom,smp2p";
+		qcom,smem = <443>, <429>;
+		interrupts-extended = <&ipcc IPCC_CLIENT_LPASS
+					     IPCC_MPROC_SIGNAL_SMP2P
+					     IRQ_TYPE_EDGE_RISING>;
+		mboxes = <&ipcc IPCC_CLIENT_LPASS
+				IPCC_MPROC_SIGNAL_SMP2P>;
+
+		qcom,local-pid = <0>;
+		qcom,remote-pid = <2>;
+
+		smp2p_adsp_out: master-kernel {
+			qcom,entry-name = "master-kernel";
+			#qcom,smem-state-cells = <1>;
+		};
+
+		smp2p_adsp_in: slave-kernel {
+			qcom,entry-name = "slave-kernel";
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	smp2p-nsp0 {
+		compatible = "qcom,smp2p";
+		qcom,smem = <94>, <432>;
+		interrupts-extended = <&ipcc IPCC_CLIENT_CDSP
+					     IPCC_MPROC_SIGNAL_SMP2P
+					     IRQ_TYPE_EDGE_RISING>;
+		mboxes = <&ipcc IPCC_CLIENT_CDSP
+				IPCC_MPROC_SIGNAL_SMP2P>;
+
+		qcom,local-pid = <0>;
+		qcom,remote-pid = <5>;
+
+		smp2p_nsp0_out: master-kernel {
+			qcom,entry-name = "master-kernel";
+			#qcom,smem-state-cells = <1>;
+		};
+
+		smp2p_nsp0_in: slave-kernel {
+			qcom,entry-name = "slave-kernel";
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	smp2p-nsp1 {
+		compatible = "qcom,smp2p";
+		qcom,smem = <617>, <616>;
+		interrupts-extended = <&ipcc IPCC_CLIENT_NSP1
+					     IPCC_MPROC_SIGNAL_SMP2P
+					     IRQ_TYPE_EDGE_RISING>;
+		mboxes = <&ipcc IPCC_CLIENT_NSP1
+				IPCC_MPROC_SIGNAL_SMP2P>;
+
+		qcom,local-pid = <0>;
+		qcom,remote-pid = <12>;
+
+		smp2p_nsp1_out: master-kernel {
+			qcom,entry-name = "master-kernel";
+			#qcom,smem-state-cells = <1>;
+		};
+
+		smp2p_nsp1_in: slave-kernel {
+			qcom,entry-name = "slave-kernel";
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	soc: soc@0 {
+		compatible = "simple-bus";
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges = <0 0 0 0 0x10 0>;
+		dma-ranges = <0 0 0 0 0x10 0>;
+
+		gcc: clock-controller@100000 {
+			compatible = "qcom,gcc-sc8280xp";
+			reg = <0x0 0x00100000 0x0 0x1f0000>;
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+			#power-domain-cells = <1>;
+			clocks = <&rpmhcc RPMH_CXO_CLK>,
+				 <&sleep_clk>,
+				 <0>,
+				 <0>,
+				 <0>,
+				 <0>,
+				 <0>,
+				 <0>,
+				 <&usb_0_ssphy>,
+				 <0>,
+				 <0>,
+				 <0>,
+				 <0>,
+				 <0>,
+				 <0>,
+				 <0>,
+				 <&usb_1_ssphy>,
+				 <0>,
+				 <0>,
+				 <0>,
+				 <0>,
+				 <0>,
+				 <0>,
+				 <0>,
+				 <0>,
+				 <0>,
+				 <0>,
+				 <0>,
+				 <0>,
+				 <0>,
+				 <0>,
+				 <0>,
+				 <0>;
+			power-domains = <&rpmhpd SC8280XP_CX>;
+		};
+
+		ipcc: mailbox@408000 {
+			compatible = "qcom,sc8280xp-ipcc", "qcom,ipcc";
+			reg = <0 0x00408000 0 0x1000>;
+			interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-controller;
+			#interrupt-cells = <3>;
+			#mbox-cells = <2>;
+		};
+
+		qup2: geniqup@8c0000 {
+			compatible = "qcom,geni-se-qup";
+			reg = <0 0x008c0000 0 0x2000>;
+			clocks = <&gcc GCC_QUPV3_WRAP_2_M_AHB_CLK>,
+				 <&gcc GCC_QUPV3_WRAP_2_S_AHB_CLK>;
+			clock-names = "m-ahb", "s-ahb";
+			iommus = <&apps_smmu 0xa3 0>;
+
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+
+			status = "disabled";
+
+			qup2_uart17: serial@884000 {
+				compatible = "qcom,geni-uart";
+				reg = <0 0x00884000 0 0x4000>;
+				clocks = <&gcc GCC_QUPV3_WRAP2_S1_CLK>;
+				clock-names = "se";
+				interrupts = <GIC_SPI 583 IRQ_TYPE_LEVEL_HIGH>;
+				operating-points-v2 = <&qup_opp_table_100mhz>;
+				power-domains = <&rpmhpd SC8280XP_CX>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_2 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			qup2_i2c5: i2c@894000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00894000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP2_S5_CLK>;
+				interrupts = <GIC_SPI 587 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				power-domains = <&rpmhpd SC8280XP_CX>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_2 0>,
+						<&aggre1_noc MASTER_QUP_2 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				status = "disabled";
+			};
+		};
+
+		qup0: geniqup@9c0000 {
+			compatible = "qcom,geni-se-qup";
+			reg = <0 0x009c0000 0 0x6000>;
+			clocks = <&gcc GCC_QUPV3_WRAP_0_M_AHB_CLK>,
+				 <&gcc GCC_QUPV3_WRAP_0_S_AHB_CLK>;
+			clock-names = "m-ahb", "s-ahb";
+			iommus = <&apps_smmu 0x563 0>;
+
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+
+			status = "disabled";
+
+			qup0_i2c4: i2c@990000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00990000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
+				interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				power-domains = <&rpmhpd SC8280XP_CX>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_0 0>,
+						<&aggre1_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				status = "disabled";
+			};
+		};
+
+		qup1: geniqup@ac0000 {
+			compatible = "qcom,geni-se-qup";
+			reg = <0 0x00ac0000 0 0x6000>;
+			clocks = <&gcc GCC_QUPV3_WRAP_1_M_AHB_CLK>,
+				 <&gcc GCC_QUPV3_WRAP_1_S_AHB_CLK>;
+			clock-names = "m-ahb", "s-ahb";
+			iommus = <&apps_smmu 0x83 0>;
+
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+
+			status = "disabled";
+		};
+
+		ufs_mem_hc: ufs@1d84000 {
+			compatible = "qcom,sc8280xp-ufshc", "qcom,ufshc",
+				     "jedec,ufs-2.0";
+			reg = <0 0x01d84000 0 0x3000>;
+			interrupts = <GIC_SPI 265 IRQ_TYPE_LEVEL_HIGH>;
+			phys = <&ufs_mem_phy_lanes>;
+			phy-names = "ufsphy";
+			lanes-per-direction = <2>;
+			#reset-cells = <1>;
+			resets = <&gcc GCC_UFS_PHY_BCR>;
+			reset-names = "rst";
+
+			power-domains = <&gcc UFS_PHY_GDSC>;
+			required-opps = <&rpmhpd_opp_nom>;
+
+			iommus = <&apps_smmu 0xe0 0x0>;
+
+			clocks = <&gcc GCC_UFS_PHY_AXI_CLK>,
+				 <&gcc GCC_AGGRE_UFS_PHY_AXI_CLK>,
+				 <&gcc GCC_UFS_PHY_AHB_CLK>,
+				 <&gcc GCC_UFS_PHY_UNIPRO_CORE_CLK>,
+				 <&rpmhcc RPMH_CXO_CLK>,
+				 <&gcc GCC_UFS_PHY_TX_SYMBOL_0_CLK>,
+				 <&gcc GCC_UFS_PHY_RX_SYMBOL_0_CLK>,
+				 <&gcc GCC_UFS_PHY_RX_SYMBOL_1_CLK>;
+			clock-names = "core_clk",
+				      "bus_aggr_clk",
+				      "iface_clk",
+				      "core_clk_unipro",
+				      "ref_clk",
+				      "tx_lane0_sync_clk",
+				      "rx_lane0_sync_clk",
+				      "rx_lane1_sync_clk";
+			freq-table-hz = <75000000 300000000>,
+					<0 0>,
+					<0 0>,
+					<75000000 300000000>,
+					<0 0>,
+					<0 0>,
+					<0 0>,
+					<0 0>;
+			status = "disabled";
+		};
+
+		ufs_mem_phy: phy@1d87000 {
+			compatible = "qcom,sc8280xp-qmp-ufs-phy";
+			reg = <0 0x01d87000 0 0xe10>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+			clock-names = "ref",
+				      "ref_aux";
+			clocks = <&rpmhcc RPMH_CXO_CLK>,
+				 <&gcc GCC_UFS_PHY_PHY_AUX_CLK>;
+
+			resets = <&ufs_mem_hc 0>;
+			reset-names = "ufsphy";
+			status = "disabled";
+
+			ufs_mem_phy_lanes: phy@1d87400 {
+				reg = <0 0x01d87400 0 0x108>,
+				      <0 0x01d87600 0 0x1e0>,
+				      <0 0x01d87c00 0 0x1dc>,
+				      <0 0x01d87800 0 0x108>,
+				      <0 0x01d87a00 0 0x1e0>;
+				#phy-cells = <0>;
+			};
+		};
+
+		ufs_card_hc: ufs@1da4000 {
+			compatible = "qcom,sc8280xp-ufshc", "qcom,ufshc",
+				     "jedec,ufs-2.0";
+			reg = <0 0x01da4000 0 0x3000>;
+			interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>;
+			phys = <&ufs_card_phy_lanes>;
+			phy-names = "ufsphy";
+			lanes-per-direction = <2>;
+			#reset-cells = <1>;
+			resets = <&gcc GCC_UFS_CARD_BCR>;
+			reset-names = "rst";
+
+			power-domains = <&gcc UFS_CARD_GDSC>;
+
+			iommus = <&apps_smmu 0x4a0 0x0>;
+
+			clocks = <&gcc GCC_UFS_CARD_AXI_CLK>,
+				 <&gcc GCC_AGGRE_UFS_CARD_AXI_CLK>,
+				 <&gcc GCC_UFS_CARD_AHB_CLK>,
+				 <&gcc GCC_UFS_CARD_UNIPRO_CORE_CLK>,
+				 <&rpmhcc RPMH_CXO_CLK>,
+				 <&gcc GCC_UFS_CARD_TX_SYMBOL_0_CLK>,
+				 <&gcc GCC_UFS_CARD_RX_SYMBOL_0_CLK>,
+				 <&gcc GCC_UFS_CARD_RX_SYMBOL_1_CLK>;
+			clock-names = "core_clk",
+				      "bus_aggr_clk",
+				      "iface_clk",
+				      "core_clk_unipro",
+				      "ref_clk",
+				      "tx_lane0_sync_clk",
+				      "rx_lane0_sync_clk",
+				      "rx_lane1_sync_clk";
+			freq-table-hz = <75000000 300000000>,
+					<0 0>,
+					<0 0>,
+					<75000000 300000000>,
+					<0 0>,
+					<0 0>,
+					<0 0>,
+					<0 0>;
+			status = "disabled";
+		};
+
+		ufs_card_phy: phy@1da7000 {
+			compatible = "qcom,sc8280xp-qmp-ufs-phy";
+			reg = <0 0x01da7000 0 0xe10>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+			clock-names = "ref",
+				      "ref_aux";
+			clocks = <&gcc GCC_UFS_1_CARD_CLKREF_CLK>,
+				 <&gcc GCC_UFS_CARD_PHY_AUX_CLK>;
+
+			resets = <&ufs_card_hc 0>;
+			reset-names = "ufsphy";
+
+			status = "disabled";
+
+			ufs_card_phy_lanes: phy@1da7400 {
+				reg = <0 0x01da7400 0 0x108>,
+				      <0 0x01da7600 0 0x1e0>,
+				      <0 0x01da7c00 0 0x1dc>,
+				      <0 0x01da7800 0 0x108>,
+				      <0 0x01da7a00 0 0x1e0>;
+				#phy-cells = <0>;
+			};
+		};
+
+		tcsr_mutex: hwlock@1f40000 {
+			compatible = "qcom,tcsr-mutex";
+			reg = <0x0 0x01f40000 0x0 0x20000>;
+			#hwlock-cells = <1>;
+		};
+
+		usb_0_hsphy: phy@88e5000 {
+			compatible = "qcom,sc8280xp-usb-hs-phy",
+				     "qcom,usb-snps-hs-5nm-phy";
+			reg = <0 0x088e5000 0 0x400>;
+			clocks = <&rpmhcc RPMH_CXO_CLK>;
+			clock-names = "ref";
+			resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>;
+
+			#phy-cells = <0>;
+
+			status = "disabled";
+		};
+
+		usb_2_hsphy0: phy@88e7000 {
+			compatible = "qcom,sc8280xp-usb-hs-phy",
+				     "qcom,usb-snps-hs-5nm-phy";
+			reg = <0 0x088e7000 0 0x400>;
+			clocks = <&gcc GCC_USB2_HS0_CLKREF_CLK>;
+			clock-names = "ref";
+			resets = <&gcc GCC_QUSB2PHY_HS0_MP_BCR>;
+
+			#phy-cells = <0>;
+
+			status = "disabled";
+		};
+
+		usb_2_hsphy1: phy@88e8000 {
+			compatible = "qcom,sc8280xp-usb-hs-phy",
+				     "qcom,usb-snps-hs-5nm-phy";
+			reg = <0 0x088e8000 0 0x400>;
+			clocks = <&gcc GCC_USB2_HS1_CLKREF_CLK>;
+			clock-names = "ref";
+			resets = <&gcc GCC_QUSB2PHY_HS1_MP_BCR>;
+
+			#phy-cells = <0>;
+
+			status = "disabled";
+		};
+
+		usb_2_hsphy2: phy@88e9000 {
+			compatible = "qcom,sc8280xp-usb-hs-phy",
+				     "qcom,usb-snps-hs-5nm-phy";
+			reg = <0 0x088e9000 0 0x400>;
+			clocks = <&gcc GCC_USB2_HS2_CLKREF_CLK>;
+			clock-names = "ref";
+			resets = <&gcc GCC_QUSB2PHY_HS2_MP_BCR>;
+
+			#phy-cells = <0>;
+
+			status = "disabled";
+		};
+
+		usb_2_hsphy3: phy@88ea000 {
+			compatible = "qcom,sc8280xp-usb-hs-phy",
+				     "qcom,usb-snps-hs-5nm-phy";
+			reg = <0 0x088ea000 0 0x400>;
+			clocks = <&gcc GCC_USB2_HS3_CLKREF_CLK>;
+			clock-names = "ref";
+			resets = <&gcc GCC_QUSB2PHY_HS3_MP_BCR>;
+
+			#phy-cells = <0>;
+
+			status = "disabled";
+		};
+
+		usb_2_qmpphy0: phy-wrapper@88ef000 {
+			compatible = "qcom,sc8280xp-qmp-usb3-uni-phy";
+			reg = <0 0x088ef000 0 0x1c8>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+
+			clocks = <&gcc GCC_USB3_MP_PHY_AUX_CLK>,
+				 <&rpmhcc RPMH_CXO_CLK>,
+				 <&gcc GCC_USB3_MP0_CLKREF_CLK>,
+				 <&gcc GCC_USB3_MP_PHY_COM_AUX_CLK>;
+			clock-names = "aux", "ref_clk_src", "ref", "com_aux";
+
+			resets = <&gcc GCC_USB3_UNIPHY_MP0_BCR>,
+				 <&gcc GCC_USB3UNIPHY_PHY_MP0_BCR>;
+			reset-names = "phy", "common";
+
+			power-domains = <&gcc USB30_MP_GDSC>;
+
+			status = "disabled";
+
+			usb_2_ssphy0: phy@88efe00 {
+				reg = <0 0x088efe00 0 0x160>,
+				      <0 0x088f0000 0 0x1ec>,
+				      <0 0x088ef200 0 0x1f0>;
+				#phy-cells = <0>;
+				#clock-cells = <0>;
+				clocks = <&gcc GCC_USB3_MP_PHY_PIPE_0_CLK>;
+				clock-names = "pipe0";
+				clock-output-names = "usb2_phy0_pipe_clk";
+			};
+		};
+
+		usb_2_qmpphy1: phy-wrapper@88f1000 {
+			compatible = "qcom,sc8280xp-qmp-usb3-uni-phy";
+			reg = <0 0x088f1000 0 0x1c8>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+
+			clocks = <&gcc GCC_USB3_MP_PHY_AUX_CLK>,
+				 <&rpmhcc RPMH_CXO_CLK>,
+				 <&gcc GCC_USB3_MP1_CLKREF_CLK>,
+				 <&gcc GCC_USB3_MP_PHY_COM_AUX_CLK>;
+			clock-names = "aux", "ref_clk_src", "ref", "com_aux";
+
+			resets = <&gcc GCC_USB3_UNIPHY_MP1_BCR>,
+				 <&gcc GCC_USB3UNIPHY_PHY_MP1_BCR>;
+			reset-names = "phy", "common";
+
+			power-domains = <&gcc USB30_MP_GDSC>;
+
+			status = "disabled";
+
+			usb_2_ssphy1: phy@88f1e00 {
+				reg = <0 0x088f1e00 0 0x160>,
+				      <0 0x088f2000 0 0x1ec>,
+				      <0 0x088f1200 0 0x1f0>;
+				#phy-cells = <0>;
+				#clock-cells = <0>;
+				clocks = <&gcc GCC_USB3_MP_PHY_PIPE_1_CLK>;
+				clock-names = "pipe0";
+				clock-output-names = "usb2_phy1_pipe_clk";
+			};
+		};
+
+		remoteproc_adsp: remoteproc@3000000 {
+			compatible = "qcom,sc8280xp-adsp-pas";
+			reg = <0 0x03000000 0 0x100>;
+
+			interrupts-extended = <&intc GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH>,
+					      <&smp2p_adsp_in 0 IRQ_TYPE_EDGE_RISING>,
+					      <&smp2p_adsp_in 1 IRQ_TYPE_EDGE_RISING>,
+					      <&smp2p_adsp_in 2 IRQ_TYPE_EDGE_RISING>,
+					      <&smp2p_adsp_in 3 IRQ_TYPE_EDGE_RISING>,
+					      <&smp2p_adsp_in 7 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "wdog", "fatal", "ready",
+					  "handover", "stop-ack", "shutdown-ack";
+
+			clocks = <&rpmhcc RPMH_CXO_CLK>;
+			clock-names = "xo";
+
+			power-domains = <&rpmhpd SC8280XP_LCX>,
+					<&rpmhpd SC8280XP_LMX>;
+			power-domain-names = "lcx", "lmx";
+
+			memory-region = <&pil_adsp_mem>;
+
+			qcom,qmp = <&aoss_qmp>;
+
+			qcom,smem-states = <&smp2p_adsp_out 0>;
+			qcom,smem-state-names = "stop";
+
+			status = "disabled";
+
+			remoteproc_adsp_glink: glink-edge {
+				interrupts-extended = <&ipcc IPCC_CLIENT_LPASS
+							     IPCC_MPROC_SIGNAL_GLINK_QMP
+							     IRQ_TYPE_EDGE_RISING>;
+				mboxes = <&ipcc IPCC_CLIENT_LPASS
+						IPCC_MPROC_SIGNAL_GLINK_QMP>;
+
+				label = "lpass";
+				qcom,remote-pid = <2>;
+			};
+		};
+
+		usb_0_qmpphy: phy-wrapper@88ec000 {
+			compatible = "qcom,sc8280xp-qmp-usb43dp-phy";
+			reg = <0 0x088ec000 0 0x1e4>,
+			      <0 0x088eb000 0 0x40>,
+			      <0 0x088ed000 0 0x1c8>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+
+			clocks = <&gcc GCC_USB3_PRIM_PHY_AUX_CLK>,
+				 <&rpmhcc RPMH_CXO_CLK>,
+				 <&gcc GCC_USB4_EUD_CLKREF_CLK>,
+				 <&gcc GCC_USB3_PRIM_PHY_COM_AUX_CLK>;
+			clock-names = "aux", "ref_clk_src", "ref", "com_aux";
+
+			resets = <&gcc GCC_USB3_PHY_PRIM_BCR>,
+				 <&gcc GCC_USB3_DP_PHY_PRIM_BCR>;
+			reset-names = "phy", "common";
+
+			power-domains = <&gcc USB30_PRIM_GDSC>;
+
+			status = "disabled";
+
+			usb_0_ssphy: usb3-phy@88eb400 {
+				reg = <0 0x088eb400 0 0x100>,
+				      <0 0x088eb600 0 0x3ec>,
+				      <0 0x088ec400 0 0x1f0>,
+				      <0 0x088eba00 0 0x100>,
+				      <0 0x088ebc00 0 0x3ec>,
+				      <0 0x088ec700 0 0x64>;
+				#phy-cells = <0>;
+				#clock-cells = <0>;
+				clocks = <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>;
+				clock-names = "pipe0";
+				clock-output-names = "usb0_phy_pipe_clk_src";
+			};
+
+			usb_0_dpphy: dp-phy@88ed200 {
+				reg = <0 0x088ed200 0 0x200>,
+				      <0 0x088ed400 0 0x200>,
+				      <0 0x088eda00 0 0x200>,
+				      <0 0x088ea600 0 0x200>,
+				      <0 0x088ea800 0 0x200>;
+				#clock-cells = <1>;
+				#phy-cells = <0>;
+			};
+		};
+
+		usb_1_hsphy: phy@8902000 {
+			compatible = "qcom,sc8280xp-usb-hs-phy",
+				     "qcom,usb-snps-hs-5nm-phy";
+			reg = <0 0x08902000 0 0x400>;
+			#phy-cells = <0>;
+
+			clocks = <&rpmhcc RPMH_CXO_CLK>;
+			clock-names = "ref";
+
+			resets = <&gcc GCC_QUSB2PHY_SEC_BCR>;
+
+			status = "disabled";
+		};
+
+		usb_1_qmpphy: phy-wrapper@8904000 {
+			compatible = "qcom,sc8280xp-qmp-usb43dp-phy";
+			reg = <0 0x08904000 0 0x1e4>,
+			      <0 0x08903000 0 0x40>,
+			      <0 0x08905000 0 0x1c8>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+
+			clocks = <&gcc GCC_USB3_SEC_PHY_AUX_CLK>,
+				 <&rpmhcc RPMH_CXO_CLK>,
+				 <&gcc GCC_USB4_CLKREF_CLK>,
+				 <&gcc GCC_USB3_SEC_PHY_COM_AUX_CLK>;
+			clock-names = "aux", "ref_clk_src", "ref", "com_aux";
+
+			resets = <&gcc GCC_USB3_PHY_SEC_BCR>,
+				 <&gcc GCC_USB4_1_DP_PHY_PRIM_BCR>;
+			reset-names = "phy", "common";
+
+			power-domains = <&gcc USB30_SEC_GDSC>;
+
+			status = "disabled";
+
+			usb_1_ssphy: usb3-phy@8903400 {
+				reg = <0 0x08903400 0 0x100>,
+				      <0 0x08903c00 0 0x3ec>,
+				      <0 0x08904400 0 0x1f0>,
+				      <0 0x08903a00 0 0x100>,
+				      <0 0x08903c00 0 0x3ec>,
+				      <0 0x08904200 0 0x18>;
+				#phy-cells = <0>;
+				#clock-cells = <0>;
+				clocks = <&gcc GCC_USB3_SEC_PHY_PIPE_CLK>;
+				clock-names = "pipe0";
+				clock-output-names = "usb1_phy_pipe_clk_src";
+			};
+
+			usb_1_dpphy: dp-phy@8904200 {
+				reg = <0 0x08904200 0 0x200>,
+				      <0 0x08904400 0 0x200>,
+				      <0 0x08904a00 0 0x200>,
+				      <0 0x08904600 0 0x200>,
+				      <0 0x08904800 0 0x200>;
+				#clock-cells = <1>;
+				#phy-cells = <0>;
+			};
+		};
+
+		system-cache-controller@9200000 {
+			compatible = "qcom,sc8280xp-llcc";
+			reg = <0 0x09200000 0 0x58000>, <0 0x09600000 0 0x58000>;
+			reg-names = "llcc_base", "llcc_broadcast_base";
+			interrupts = <GIC_SPI 582 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		usb_0: usb@a6f8800 {
+			compatible = "qcom,sc8280xp-dwc3", "qcom,dwc3";
+			reg = <0 0x0a6f8800 0 0x400>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+
+			clocks = <&gcc GCC_CFG_NOC_USB3_PRIM_AXI_CLK>,
+				 <&gcc GCC_USB30_PRIM_MASTER_CLK>,
+				 <&gcc GCC_AGGRE_USB3_PRIM_AXI_CLK>,
+				 <&gcc GCC_USB30_PRIM_SLEEP_CLK>,
+				 <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
+				 <&gcc GCC_AGGRE_USB_NOC_AXI_CLK>,
+				 <&gcc GCC_AGGRE_USB_NOC_NORTH_AXI_CLK>,
+				 <&gcc GCC_AGGRE_USB_NOC_SOUTH_AXI_CLK>,
+				 <&gcc GCC_SYS_NOC_USB_AXI_CLK>;
+			clock-names = "cfg_noc", "core", "iface", "sleep", "mock_utmi",
+				      "noc_aggr", "noc_aggr_north", "noc_aggr_south", "noc_sys";
+
+			assigned-clocks = <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
+					  <&gcc GCC_USB30_PRIM_MASTER_CLK>;
+			assigned-clock-rates = <19200000>, <200000000>;
+
+			interrupts-extended = <&intc GIC_SPI 804 IRQ_TYPE_LEVEL_HIGH>,
+					      <&pdc 14 IRQ_TYPE_EDGE_BOTH>,
+					      <&pdc 15 IRQ_TYPE_EDGE_BOTH>,
+					      <&pdc 138 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "pwr_event",
+					  "dp_hs_phy_irq",
+					  "dm_hs_phy_irq",
+					  "ss_phy_irq";
+
+			power-domains = <&gcc USB30_PRIM_GDSC>;
+
+			resets = <&gcc GCC_USB30_PRIM_BCR>;
+
+			interconnects = <&aggre1_noc MASTER_USB3_0 0 &mc_virt SLAVE_EBI1 0>,
+					<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_USB3_0 0>;
+			interconnect-names = "usb-ddr", "apps-usb";
+
+			wakeup-source;
+
+			status = "disabled";
+
+			usb_0_dwc3: usb@a600000 {
+				compatible = "snps,dwc3";
+				reg = <0 0x0a600000 0 0xcd00>;
+				interrupts = <GIC_SPI 803 IRQ_TYPE_LEVEL_HIGH>;
+				iommus = <&apps_smmu 0x820 0x0>;
+				phys = <&usb_0_hsphy>, <&usb_0_ssphy>;
+				phy-names = "usb2-phy", "usb3-phy";
+			};
+		};
+
+		usb_1: usb@a8f8800 {
+			compatible = "qcom,sc8280xp-dwc3", "qcom,dwc3";
+			reg = <0 0x0a8f8800 0 0x400>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+
+			clocks = <&gcc GCC_CFG_NOC_USB3_SEC_AXI_CLK>,
+				 <&gcc GCC_USB30_SEC_MASTER_CLK>,
+				 <&gcc GCC_AGGRE_USB3_SEC_AXI_CLK>,
+				 <&gcc GCC_USB30_SEC_SLEEP_CLK>,
+				 <&gcc GCC_USB30_SEC_MOCK_UTMI_CLK>,
+				 <&gcc GCC_AGGRE_USB_NOC_AXI_CLK>,
+				 <&gcc GCC_AGGRE_USB_NOC_NORTH_AXI_CLK>,
+				 <&gcc GCC_AGGRE_USB_NOC_SOUTH_AXI_CLK>,
+				 <&gcc GCC_SYS_NOC_USB_AXI_CLK>;
+			clock-names = "cfg_noc", "core", "iface", "sleep", "mock_utmi",
+				      "noc_aggr", "noc_aggr_north", "noc_aggr_south", "noc_sys";
+
+			assigned-clocks = <&gcc GCC_USB30_SEC_MOCK_UTMI_CLK>,
+					  <&gcc GCC_USB30_SEC_MASTER_CLK>;
+			assigned-clock-rates = <19200000>, <200000000>;
+
+			interrupts-extended = <&intc GIC_SPI 811 IRQ_TYPE_LEVEL_HIGH>,
+					      <&pdc 12 IRQ_TYPE_EDGE_BOTH>,
+					      <&pdc 13 IRQ_TYPE_EDGE_BOTH>,
+					      <&pdc 136 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "pwr_event",
+					  "dp_hs_phy_irq",
+					  "dm_hs_phy_irq",
+					  "ss_phy_irq";
+
+			power-domains = <&gcc USB30_SEC_GDSC>;
+
+			resets = <&gcc GCC_USB30_SEC_BCR>;
+
+			interconnects = <&aggre1_noc MASTER_USB3_1 0 &mc_virt SLAVE_EBI1 0>,
+					<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_USB3_1 0>;
+			interconnect-names = "usb-ddr", "apps-usb";
+
+			wakeup-source;
+
+			status = "disabled";
+
+			usb_1_dwc3: usb@a800000 {
+				compatible = "snps,dwc3";
+				reg = <0 0x0a800000 0 0xcd00>;
+				interrupts = <GIC_SPI 810 IRQ_TYPE_LEVEL_HIGH>;
+				iommus = <&apps_smmu 0x860 0x0>;
+				phys = <&usb_1_hsphy>, <&usb_1_ssphy>;
+				phy-names = "usb2-phy", "usb3-phy";
+			};
+		};
+
+		pdc: interrupt-controller@b220000 {
+			compatible = "qcom,sc8280xp-pdc", "qcom,pdc";
+			reg = <0 0x0b220000 0 0x30000>, <0 0x17c000f0 0 0x60>;
+			qcom,pdc-ranges = <0 480 40>,
+					  <40 140 14>,
+					  <54 263 1>,
+					  <55 306 4>,
+					  <59 312 3>,
+					  <62 374 2>,
+					  <64 434 2>,
+					  <66 438 3>,
+					  <69 86 1>,
+					  <70 520 54>,
+					  <124 609 28>,
+					  <159 638 1>,
+					  <160 720 8>,
+					  <168 801 1>,
+					  <169 728 30>,
+					  <199 416 2>,
+					  <201 449 1>,
+					  <202 89 1>,
+					  <203 451 1>,
+					  <204 462 1>,
+					  <205 264 1>,
+					  <206 579 1>,
+					  <207 653 1>,
+					  <208 656 1>,
+					  <209 659 1>,
+					  <210 122 1>,
+					  <211 699 1>,
+					  <212 705 1>,
+					  <213 450 1>,
+					  <214 643 1>,
+					  <216 646 5>,
+					  <221 390 5>,
+					  <226 700 3>,
+					  <229 240 3>,
+					  <232 269 1>,
+					  <233 377 1>,
+					  <234 372 1>,
+					  <235 138 1>,
+					  <236 857 1>,
+					  <237 860 1>,
+					  <238 137 1>,
+					  <239 668 1>,
+					  <240 366 1>,
+					  <241 949 1>,
+					  <242 815 5>,
+					  <247 769 1>,
+					  <248 768 1>,
+					  <249 663 1>,
+					  <250 799 2>,
+					  <252 798 1>,
+					  <253 765 1>,
+					  <254 763 1>,
+					  <255 454 1>,
+					  <258 139 1>,
+					  <259 786 2>,
+					  <261 370 2>,
+					  <263 158 2>;
+			#interrupt-cells = <2>;
+			interrupt-parent = <&intc>;
+			interrupt-controller;
+		};
+
+		tsens0: thermal-sensor@c263000 {
+			compatible = "qcom,sc8280xp-tsens", "qcom,tsens-v2";
+			reg = <0 0x0c263000 0 0x1ff>, /* TM */
+			      <0 0x0c222000 0 0x8>; /* SROT */
+			#qcom,sensors = <14>;
+			interrupts-extended = <&pdc 26 IRQ_TYPE_LEVEL_HIGH>,
+					      <&pdc 28 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "uplow", "critical";
+			#thermal-sensor-cells = <1>;
+		};
+
+		tsens1: thermal-sensor@c265000 {
+			compatible = "qcom,sc8280xp-tsens", "qcom,tsens-v2";
+			reg = <0 0x0c265000 0 0x1ff>, /* TM */
+			      <0 0x0c223000 0 0x8>; /* SROT */
+			#qcom,sensors = <16>;
+			interrupts-extended = <&pdc 27 IRQ_TYPE_LEVEL_HIGH>,
+					      <&pdc 29 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "uplow", "critical";
+			#thermal-sensor-cells = <1>;
+		};
+
+		aoss_qmp: power-controller@c300000 {
+			compatible = "qcom,sc8280xp-aoss-qmp", "qcom,aoss-qmp";
+			reg = <0 0x0c300000 0 0x400>;
+			interrupts-extended = <&ipcc IPCC_CLIENT_AOP IPCC_MPROC_SIGNAL_GLINK_QMP IRQ_TYPE_EDGE_RISING>;
+			mboxes = <&ipcc IPCC_CLIENT_AOP IPCC_MPROC_SIGNAL_GLINK_QMP>;
+
+			#clock-cells = <0>;
+		};
+
+		spmi_bus: spmi@c440000 {
+			compatible = "qcom,spmi-pmic-arb";
+			reg = <0 0x0c440000 0 0x1100>,
+			      <0 0x0c600000 0 0x2000000>,
+			      <0 0x0e600000 0 0x100000>,
+			      <0 0x0e700000 0 0xa0000>,
+			      <0 0x0c40a000 0 0x26000>;
+			reg-names = "core", "chnls", "obsrvr", "intr", "cnfg";
+			interrupt-names = "periph_irq";
+			interrupts-extended = <&pdc 1 IRQ_TYPE_LEVEL_HIGH>;
+			qcom,ee = <0>;
+			qcom,channel = <0>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			interrupt-controller;
+			#interrupt-cells = <4>;
+		};
+
+		tlmm: pinctrl@f100000 {
+			compatible = "qcom,sc8280xp-tlmm";
+			reg = <0 0x0f100000 0 0x300000>;
+			interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			gpio-ranges = <&tlmm 0 0 230>;
+		};
+
+		apps_smmu: iommu@15000000 {
+			compatible = "qcom,sc8280xp-smmu-500", "arm,mmu-500";
+			reg = <0 0x15000000 0 0x100000>;
+			#iommu-cells = <2>;
+			#global-interrupts = <2>;
+			interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 181 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 182 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 185 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 187 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 189 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 191 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 315 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 316 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 317 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 318 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 319 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 320 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 321 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 322 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 323 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 324 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 325 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 326 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 327 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 328 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 329 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 333 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 334 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 335 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 336 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 337 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 338 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 339 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 340 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 341 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 342 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 343 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 344 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 345 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 395 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 396 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 397 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 398 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 399 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 400 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 401 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 402 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 403 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 404 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 405 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 406 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 407 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 408 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 409 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 418 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 419 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 412 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 421 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 706 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 423 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 424 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 425 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 689 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 690 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 691 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 692 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 693 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 694 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 695 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 696 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 410 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 411 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 420 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 413 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 422 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 707 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 708 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 709 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 710 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 711 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 414 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 712 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 713 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 714 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 715 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 912 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 911 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 910 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 909 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 908 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 907 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 906 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 905 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 904 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 903 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 902 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 901 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 900 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 899 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 898 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 897 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 896 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 895 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 894 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 893 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 892 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 891 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 890 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		intc: interrupt-controller@17a00000 {
+			compatible = "arm,gic-v3";
+			interrupt-controller;
+			#interrupt-cells = <3>;
+			reg = <0x0 0x17a00000 0x0 0x10000>,	/* GICD */
+			      <0x0 0x17a60000 0x0 0x100000>;	/* GICR * 8 */
+			interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
+			#redistributor-regions = <1>;
+			redistributor-stride = <0 0x20000>;
+
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+
+			gic-its@17a40000 {
+				compatible = "arm,gic-v3-its";
+				reg = <0 0x17a40000 0 0x20000>;
+				msi-controller;
+				#msi-cells = <1>;
+			};
+		};
+
+		watchdog@17c10000 {
+			compatible = "qcom,apss-wdt-sc8280xp", "qcom,kpss-wdt";
+			reg = <0 0x17c10000 0 0x1000>;
+			clocks = <&sleep_clk>;
+			interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		timer@17c20000 {
+			compatible = "arm,armv7-timer-mem";
+			reg = <0x0 0x17c20000 0x0 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0x0 0x0 0x0 0x20000000>;
+
+			frame@17c21000 {
+				frame-number = <0>;
+				interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x17c21000 0x1000>,
+				      <0x17c22000 0x1000>;
+			};
+
+			frame@17c23000 {
+				frame-number = <1>;
+				interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x17c23000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@17c25000 {
+				frame-number = <2>;
+				interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x17c25000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@17c27000 {
+				frame-number = <3>;
+				interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x17c26000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@17c29000 {
+				frame-number = <4>;
+				interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x17c29000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@17c2b000 {
+				frame-number = <5>;
+				interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x17c2b000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@17c2d000 {
+				frame-number = <6>;
+				interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x17c2d000 0x1000>;
+				status = "disabled";
+			};
+		};
+
+		apps_rsc: rsc@18200000 {
+			compatible = "qcom,rpmh-rsc";
+			reg = <0x0 0x18200000 0x0 0x10000>,
+				<0x0 0x18210000 0x0 0x10000>,
+				<0x0 0x18220000 0x0 0x10000>;
+			reg-names = "drv-0", "drv-1", "drv-2";
+			interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
+			qcom,tcs-offset = <0xd00>;
+			qcom,drv-id = <2>;
+			qcom,tcs-config = <ACTIVE_TCS  2>, <SLEEP_TCS   3>,
+					  <WAKE_TCS    3>, <CONTROL_TCS 1>;
+			label = "apps_rsc";
+
+			apps_bcm_voter: bcm-voter {
+				compatible = "qcom,bcm-voter";
+			};
+
+			rpmhcc: clock-controller {
+				compatible = "qcom,sc8280xp-rpmh-clk";
+				#clock-cells = <1>;
+				clock-names = "xo";
+				clocks = <&xo_board_clk>;
+			};
+
+			rpmhpd: power-controller {
+				compatible = "qcom,sc8280xp-rpmhpd";
+				#power-domain-cells = <1>;
+				operating-points-v2 = <&rpmhpd_opp_table>;
+
+				rpmhpd_opp_table: opp-table {
+					compatible = "operating-points-v2";
+
+					rpmhpd_opp_ret: opp1 {
+						opp-level = <RPMH_REGULATOR_LEVEL_RETENTION>;
+					};
+
+					rpmhpd_opp_min_svs: opp2 {
+						opp-level = <RPMH_REGULATOR_LEVEL_MIN_SVS>;
+					};
+
+					rpmhpd_opp_low_svs: opp3 {
+						opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>;
+					};
+
+					rpmhpd_opp_svs: opp4 {
+						opp-level = <RPMH_REGULATOR_LEVEL_SVS>;
+					};
+
+					rpmhpd_opp_svs_l1: opp5 {
+						opp-level = <RPMH_REGULATOR_LEVEL_SVS_L1>;
+					};
+
+					rpmhpd_opp_nom: opp6 {
+						opp-level = <RPMH_REGULATOR_LEVEL_NOM>;
+					};
+
+					rpmhpd_opp_nom_l1: opp7 {
+						opp-level = <RPMH_REGULATOR_LEVEL_NOM_L1>;
+					};
+
+					rpmhpd_opp_nom_l2: opp8 {
+						opp-level = <RPMH_REGULATOR_LEVEL_NOM_L2>;
+					};
+
+					rpmhpd_opp_turbo: opp9 {
+						opp-level = <RPMH_REGULATOR_LEVEL_TURBO>;
+					};
+
+					rpmhpd_opp_turbo_l1: opp10 {
+						opp-level = <RPMH_REGULATOR_LEVEL_TURBO_L1>;
+					};
+				};
+			};
+		};
+
+		cpufreq_hw: cpufreq@18591000 {
+			compatible = "qcom,sc8280xp-cpufreq-epss", "qcom,cpufreq-epss";
+			reg = <0 0x18591000 0 0x1000>,
+			      <0 0x18592000 0 0x1000>;
+			reg-names = "freq-domain0", "freq-domain1";
+
+			clocks = <&rpmhcc RPMH_CXO_CLK>, <&gcc GCC_GPLL0>;
+			clock-names = "xo", "alternate";
+
+			#freq-domain-cells = <1>;
+		};
+
+		remoteproc_nsp0: remoteproc@1b300000 {
+			compatible = "qcom,sc8280xp-nsp0-pas";
+			reg = <0 0x1b300000 0 0x100>;
+
+			interrupts-extended = <&intc GIC_SPI 578 IRQ_TYPE_LEVEL_HIGH>,
+					      <&smp2p_nsp0_in 0 IRQ_TYPE_EDGE_RISING>,
+					      <&smp2p_nsp0_in 1 IRQ_TYPE_EDGE_RISING>,
+					      <&smp2p_nsp0_in 2 IRQ_TYPE_EDGE_RISING>,
+					      <&smp2p_nsp0_in 3 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "wdog", "fatal", "ready",
+					  "handover", "stop-ack";
+
+			clocks = <&rpmhcc RPMH_CXO_CLK>;
+			clock-names = "xo";
+
+			power-domains = <&rpmhpd SC8280XP_NSP>;
+			power-domain-names = "nsp";
+
+			memory-region = <&pil_nsp0_mem>;
+
+			qcom,smem-states = <&smp2p_nsp0_out 0>;
+			qcom,smem-state-names = "stop";
+
+			interconnects = <&nspa_noc MASTER_CDSP_PROC 0 &mc_virt SLAVE_EBI1 0>;
+
+			status = "disabled";
+
+			glink-edge {
+				interrupts-extended = <&ipcc IPCC_CLIENT_CDSP
+							     IPCC_MPROC_SIGNAL_GLINK_QMP
+							     IRQ_TYPE_EDGE_RISING>;
+				mboxes = <&ipcc IPCC_CLIENT_CDSP
+						IPCC_MPROC_SIGNAL_GLINK_QMP>;
+
+				label = "nsp0";
+				qcom,remote-pid = <5>;
+
+				fastrpc {
+					compatible = "qcom,fastrpc";
+					qcom,glink-channels = "fastrpcglink-apps-dsp";
+					label = "cdsp";
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					compute-cb@1 {
+						compatible = "qcom,fastrpc-compute-cb";
+						reg = <1>;
+						iommus = <&apps_smmu 0x3181 0x0420>;
+					};
+
+					compute-cb@2 {
+						compatible = "qcom,fastrpc-compute-cb";
+						reg = <2>;
+						iommus = <&apps_smmu 0x3182 0x0420>;
+					};
+
+					compute-cb@3 {
+						compatible = "qcom,fastrpc-compute-cb";
+						reg = <3>;
+						iommus = <&apps_smmu 0x3183 0x0420>;
+					};
+
+					compute-cb@4 {
+						compatible = "qcom,fastrpc-compute-cb";
+						reg = <4>;
+						iommus = <&apps_smmu 0x3184 0x0420>;
+					};
+
+					compute-cb@5 {
+						compatible = "qcom,fastrpc-compute-cb";
+						reg = <5>;
+						iommus = <&apps_smmu 0x3185 0x0420>;
+					};
+
+					compute-cb@6 {
+						compatible = "qcom,fastrpc-compute-cb";
+						reg = <6>;
+						iommus = <&apps_smmu 0x3186 0x0420>;
+					};
+
+					compute-cb@7 {
+						compatible = "qcom,fastrpc-compute-cb";
+						reg = <7>;
+						iommus = <&apps_smmu 0x3187 0x0420>;
+					};
+
+					compute-cb@8 {
+						compatible = "qcom,fastrpc-compute-cb";
+						reg = <8>;
+						iommus = <&apps_smmu 0x3188 0x0420>;
+					};
+
+					compute-cb@9 {
+						compatible = "qcom,fastrpc-compute-cb";
+						reg = <9>;
+						iommus = <&apps_smmu 0x318b 0x0420>;
+					};
+
+					compute-cb@10 {
+						compatible = "qcom,fastrpc-compute-cb";
+						reg = <10>;
+						iommus = <&apps_smmu 0x318b 0x0420>;
+					};
+
+					compute-cb@11 {
+						compatible = "qcom,fastrpc-compute-cb";
+						reg = <11>;
+						iommus = <&apps_smmu 0x318c 0x0420>;
+					};
+
+					compute-cb@12 {
+						compatible = "qcom,fastrpc-compute-cb";
+						reg = <12>;
+						iommus = <&apps_smmu 0x318d 0x0420>;
+					};
+
+					compute-cb@13 {
+						compatible = "qcom,fastrpc-compute-cb";
+						reg = <13>;
+						iommus = <&apps_smmu 0x318e 0x0420>;
+					};
+
+					compute-cb@14 {
+						compatible = "qcom,fastrpc-compute-cb";
+						reg = <14>;
+						iommus = <&apps_smmu 0x318f 0x0420>;
+					};
+				};
+			};
+		};
+
+		remoteproc_nsp1: remoteproc@21300000 {
+			compatible = "qcom,sc8280xp-nsp1-pas";
+			reg = <0 0x21300000 0 0x100>;
+
+			interrupts-extended = <&intc GIC_SPI 887 IRQ_TYPE_LEVEL_HIGH>,
+					      <&smp2p_nsp1_in 0 IRQ_TYPE_EDGE_RISING>,
+					      <&smp2p_nsp1_in 1 IRQ_TYPE_EDGE_RISING>,
+					      <&smp2p_nsp1_in 2 IRQ_TYPE_EDGE_RISING>,
+					      <&smp2p_nsp1_in 3 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "wdog", "fatal", "ready",
+					  "handover", "stop-ack";
+
+			clocks = <&rpmhcc RPMH_CXO_CLK>;
+			clock-names = "xo";
+
+			power-domains = <&rpmhpd SC8280XP_NSP>;
+			power-domain-names = "nsp";
+
+			memory-region = <&pil_nsp1_mem>;
+
+			qcom,smem-states = <&smp2p_nsp1_out 0>;
+			qcom,smem-state-names = "stop";
+
+			interconnects = <&nspb_noc MASTER_CDSP_PROC_B 0 &mc_virt SLAVE_EBI1 0>;
+
+			status = "disabled";
+
+			glink-edge {
+				interrupts-extended = <&ipcc IPCC_CLIENT_NSP1
+							     IPCC_MPROC_SIGNAL_GLINK_QMP
+							     IRQ_TYPE_EDGE_RISING>;
+				mboxes = <&ipcc IPCC_CLIENT_NSP1
+						IPCC_MPROC_SIGNAL_GLINK_QMP>;
+
+				label = "nsp1";
+				qcom,remote-pid = <12>;
+			};
+		};
+	};
+
+	thermal-zones {
+		cpu0-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens0 1>;
+
+			trips {
+				cpu-crit {
+					temperature = <110000>;
+					hysteresis = <1000>;
+					type = "critical";
+				};
+			};
+		};
+
+		cpu1-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens0 2>;
+
+			trips {
+				cpu-crit {
+					temperature = <110000>;
+					hysteresis = <1000>;
+					type = "critical";
+				};
+			};
+		};
+
+		cpu2-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens0 3>;
+
+			trips {
+				cpu-crit {
+					temperature = <110000>;
+					hysteresis = <1000>;
+					type = "critical";
+				};
+			};
+		};
+
+		cpu3-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens0 4>;
+
+			trips {
+				cpu-crit {
+					temperature = <110000>;
+					hysteresis = <1000>;
+					type = "critical";
+				};
+			};
+		};
+
+		cpu4-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens0 5>;
+
+			trips {
+				cpu-crit {
+					temperature = <110000>;
+					hysteresis = <1000>;
+					type = "critical";
+				};
+			};
+		};
+
+		cpu5-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens0 6>;
+
+			trips {
+				cpu-crit {
+					temperature = <110000>;
+					hysteresis = <1000>;
+					type = "critical";
+				};
+			};
+		};
+
+		cpu6-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens0 7>;
+
+			trips {
+				cpu-crit {
+					temperature = <110000>;
+					hysteresis = <1000>;
+					type = "critical";
+				};
+			};
+		};
+
+		cpu7-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens0 8>;
+
+			trips {
+				cpu-crit {
+					temperature = <110000>;
+					hysteresis = <1000>;
+					type = "critical";
+				};
+			};
+		};
+
+		cluster0-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens0 9>;
+
+			trips {
+				cpu-crit {
+					temperature = <110000>;
+					hysteresis = <1000>;
+					type = "critical";
+				};
+			};
+		};
+
+		mem-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens1 15>;
+
+			trips {
+				trip-point0 {
+					temperature = <90000>;
+					hysteresis = <2000>;
+					type = "hot";
+				};
+			};
+		};
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>;
+	};
+};
diff --git a/arch/arm64/boot/dts/qcom/sda660-inforce-ifc6560.dts b/arch/arm64/boot/dts/qcom/sda660-inforce-ifc6560.dts
new file mode 100644
index 000000000000..28050bc5f081
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sda660-inforce-ifc6560.dts
@@ -0,0 +1,461 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, Linaro Ltd.
+ * Copyright (c) 2020, Konrad Dybcio <konrad.dybcio@somainline.org>
+ * Copyright (c) 2020, AngeloGioacchino Del Regno
+ *                     <angelogioacchino.delregno@somainline.org>
+ */
+
+/dts-v1/;
+
+#include "sdm660.dtsi"
+#include "pm660.dtsi"
+#include "pm660l.dtsi"
+
+/ {
+	model = "Inforce 6560 Single Board Computer";
+	compatible = "inforce,ifc6560", "qcom,sda660";
+	chassis-type = "embedded"; /* SBC */
+
+	aliases {
+		serial0 = &blsp1_uart2;
+		serial1 = &blsp2_uart1;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		volup {
+			label = "Volume Up";
+			gpios = <&pm660l_gpios 7 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+			debounce-interval = <15>;
+		};
+	};
+
+	/*
+	 * Until we hook up type-c detection, we
+	 * have to stick with this. But it works.
+	 */
+	extcon_usb: extcon-usb {
+		compatible = "linux,extcon-usb-gpio";
+		id-gpio = <&tlmm 58 GPIO_ACTIVE_HIGH>;
+	};
+
+	hdmi-out {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con: endpoint {
+				remote-endpoint = <&adv7533_out>;
+			};
+		};
+	};
+
+	vph_pwr: vph-pwr-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vph_pwr";
+		regulator-min-microvolt = <3800000>;
+		regulator-max-microvolt = <3800000>;
+
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	v3p3_bck_bst: v3p3-bck-bst-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "v3p3_bck_bst";
+
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		vin-supply = <&vph_pwr>;
+	};
+
+	v1p2_ldo: v1p2-ldo-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "v1p2_ldo";
+
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <1200000>;
+
+		vin-supply = <&vph_pwr>;
+	};
+
+	v5p0_boost: v5p0-boost-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "v5p0_boost";
+
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+
+		vin-supply = <&vph_pwr>;
+	};
+};
+
+&adsp_pil {
+	firmware-name = "qcom/ifc6560/adsp.mbn";
+};
+
+&blsp_i2c6 {
+	status = "okay";
+
+	adv7533: hdmi@39 {
+		compatible = "adi,adv7535";
+		reg = <0x39>, <0x66>;
+		reg-names = "main", "edid";
+
+		interrupt-parent = <&pm660l_gpios>;
+		interrupts = <11 IRQ_TYPE_EDGE_FALLING>;
+
+		clocks = <&rpmcc RPM_SMD_BB_CLK2>;
+		clock-names = "cec";
+		/*
+		 * Limit to 3 lanes to prevent the bridge from changing amount
+		 * of lanes in the fly. MSM DSI host doesn't like that.
+		 */
+		adi,dsi-lanes = <3>;
+		avdd-supply = <&vreg_l13a_1p8>;
+		dvdd-supply = <&vreg_l13a_1p8>;
+		pvdd-supply = <&vreg_l13a_1p8>;
+		a2vdd-supply = <&vreg_l13a_1p8>;
+		v3p3-supply = <&v3p3_bck_bst>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				adv7533_in: endpoint {
+					remote-endpoint = <&dsi0_out>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				adv7533_out: endpoint {
+					remote-endpoint = <&hdmi_con>;
+				};
+			};
+		};
+	};
+};
+
+&blsp1_dma {
+	/*
+	 * The board will lock up if we toggle the BLSP clock, unless the
+	 * BAM DMA interconnects support is in place.
+	 */
+	/delete-property/ clocks;
+};
+
+&blsp1_uart2 {
+	status = "okay";
+};
+
+&blsp2_dma {
+	/*
+	 * The board will lock up if we toggle the BLSP clock, unless the
+	 * BAM DMA interconnects support is in place.
+	 */
+	/delete-property/ clocks;
+};
+
+&blsp2_uart1 {
+	status = "okay";
+
+	bluetooth {
+		compatible = "qcom,wcn3990-bt";
+
+		vddio-supply = <&vreg_l13a_1p8>;
+		vddxo-supply = <&vreg_l9a_1p8>;
+		vddrf-supply = <&vreg_l6a_1p3>;
+		vddch0-supply = <&vreg_l19a_3p3>;
+		max-speed = <3200000>;
+	};
+};
+
+&dsi0 {
+	status = "okay";
+	vdda-supply = <&vreg_l1a_1p225>;
+};
+
+&dsi0_out {
+	remote-endpoint = <&adv7533_in>;
+	data-lanes = <0 1 2 3>;
+};
+
+&dsi0_phy {
+	status = "okay";
+	vcca-supply = <&vreg_l1b_0p925>;
+};
+
+&mdss {
+	status = "okay";
+};
+
+&mmss_smmu {
+	status = "okay";
+};
+
+&pon_pwrkey {
+	status = "okay";
+};
+
+&pon_resin {
+	status = "okay";
+
+	linux,code = <KEY_VOLUMEUP>;
+};
+
+&qusb2phy0 {
+	status = "okay";
+
+	vdd-supply = <&vreg_l1b_0p925>;
+	vdda-phy-dpdm-supply = <&vreg_l7b_3p125>;
+};
+
+&qusb2phy1 {
+	status = "okay";
+
+	vdd-supply = <&vreg_l1b_0p925>;
+	vdda-phy-dpdm-supply = <&vreg_l7b_3p125>;
+};
+
+&rpm_requests {
+	pm660-regulators {
+		compatible = "qcom,rpm-pm660-regulators";
+
+		vdd_s1-supply = <&vph_pwr>;
+		vdd_s2-supply = <&vph_pwr>;
+		vdd_s3-supply = <&vph_pwr>;
+		vdd_s4-supply = <&vph_pwr>;
+		vdd_s5-supply = <&vph_pwr>;
+		vdd_s6-supply = <&vph_pwr>;
+
+		vdd_l1_l6_l7-supply = <&vreg_s5a_1p35>;
+		vdd_l2_l3-supply = <&vreg_s2b_1p05>;
+		vdd_l5-supply = <&vreg_s2b_1p05>;
+		vdd_l8_l9_l10_l11_l12_l13_l14-supply = <&vreg_s4a_2p04>;
+		vdd_l15_l16_l17_l18_l19-supply = <&vreg_bob>;
+
+		vreg_s4a_2p04: s4 {
+			regulator-min-microvolt = <1805000>;
+			regulator-max-microvolt = <2040000>;
+			regulator-enable-ramp-delay = <200>;
+			regulator-ramp-delay = <0>;
+			regulator-always-on;
+		};
+
+		vreg_s5a_1p35: s5 {
+			regulator-min-microvolt = <1224000>;
+			regulator-max-microvolt = <1350000>;
+			regulator-enable-ramp-delay = <200>;
+			regulator-ramp-delay = <0>;
+		};
+
+		vreg_l1a_1p225: l1 {
+			regulator-min-microvolt = <1150000>;
+			regulator-max-microvolt = <1250000>;
+			regulator-enable-ramp-delay = <250>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l6a_1p3: l6 {
+			regulator-min-microvolt = <1304000>;
+			regulator-max-microvolt = <1368000>;
+			regulator-enable-ramp-delay = <250>;
+			regulator-ramp-delay = <0>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l8a_1p8: l8 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-enable-ramp-delay = <250>;
+			regulator-ramp-delay = <0>;
+			regulator-system-load = <325000>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l9a_1p8: l9 {
+			regulator-min-microvolt = <1804000>;
+			regulator-max-microvolt = <1896000>;
+			regulator-enable-ramp-delay = <250>;
+			regulator-ramp-delay = <0>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l13a_1p8: l13 {
+			/* This gives power to the LPDDR4: never turn it off! */
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1944000>;
+			regulator-enable-ramp-delay = <250>;
+			regulator-ramp-delay = <0>;
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		vreg_l19a_3p3: l19 {
+			regulator-min-microvolt = <3312000>;
+			regulator-max-microvolt = <3400000>;
+			regulator-enable-ramp-delay = <250>;
+			regulator-ramp-delay = <0>;
+			regulator-allow-set-load;
+		};
+	};
+
+	pm660l-regulators {
+		compatible = "qcom,rpm-pm660l-regulators";
+
+		vdd_s1-supply = <&vph_pwr>;
+		vdd_s2-supply = <&vph_pwr>;
+		vdd_s3_s4-supply = <&vph_pwr>;
+		vdd_s5-supply = <&vph_pwr>;
+		vdd_s6-supply = <&vph_pwr>;
+
+		vdd_l1_l9_l10-supply = <&vreg_s2b_1p05>;
+		vdd_l2-supply = <&vreg_bob>;
+		vdd_l3_l5_l7_l8-supply = <&vreg_bob>;
+		vdd_l4_l6-supply = <&vreg_bob>;
+		vdd_bob-supply = <&vph_pwr>;
+
+		vreg_s2b_1p05: s2 {
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1050000>;
+			regulator-enable-ramp-delay = <200>;
+			regulator-ramp-delay = <0>;
+		};
+
+		vreg_l1b_0p925: l1 {
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <925000>;
+			regulator-enable-ramp-delay = <250>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l2b_2p95: l2 {
+			regulator-min-microvolt = <1648000>;
+			regulator-max-microvolt = <3100000>;
+			regulator-enable-ramp-delay = <250>;
+			regulator-ramp-delay = <0>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l4b_2p95: l4 {
+			regulator-min-microvolt = <2944000>;
+			regulator-max-microvolt = <2952000>;
+			regulator-enable-ramp-delay = <250>;
+			regulator-ramp-delay = <0>;
+
+			regulator-min-microamp = <200>;
+			regulator-max-microamp = <600000>;
+			regulator-system-load = <570000>;
+			regulator-allow-set-load;
+		};
+
+		/*
+		 * Downstream specifies a range of 1721-3600mV,
+		 * but the only assigned consumers are SDHCI2 VMMC
+		 * and Coresight QPDI that both request pinned 2.95V.
+		 * Tighten the range to 1.8-3.328 (closest to 3.3) to
+		 * make the mmc driver happy.
+		 */
+		vreg_l5b_2p95: l5 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <3328000>;
+			regulator-enable-ramp-delay = <250>;
+			regulator-system-load = <800000>;
+			regulator-ramp-delay = <0>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l7b_3p125: l7 {
+			regulator-min-microvolt = <2700000>;
+			regulator-max-microvolt = <3125000>;
+			regulator-enable-ramp-delay = <250>;
+		};
+
+		vreg_l8b_3p3: l8 {
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <3400000>;
+			regulator-enable-ramp-delay = <250>;
+			regulator-ramp-delay = <0>;
+		};
+
+		vreg_bob: bob {
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3624000>;
+			regulator-enable-ramp-delay = <500>;
+			regulator-ramp-delay = <0>;
+		};
+	};
+};
+
+&sdc2_state_on {
+	sd-cd {
+		pins = "gpio54";
+		bias-pull-up;
+		drive-strength = <2>;
+	};
+};
+
+&sdc2_state_off {
+	sd-cd {
+		pins = "gpio54";
+		bias-disable;
+		drive-strength = <2>;
+	};
+};
+
+&sdhc_1 {
+	status = "okay";
+	supports-cqe;
+
+	vmmc-supply = <&vreg_l4b_2p95>;
+	vqmmc-supply = <&vreg_l8a_1p8>;
+
+	mmc-ddr-1_8v;
+	mmc-hs400-1_8v;
+	mmc-hs400-enhanced-strobe;
+};
+
+&sdhc_2 {
+	status = "okay";
+
+	vmmc-supply = <&vreg_l5b_2p95>;
+	vqmmc-supply = <&vreg_l2b_2p95>;
+
+	cd-gpios = <&tlmm 54 GPIO_ACTIVE_LOW>;
+	no-sdio;
+	no-emmc;
+};
+
+&tlmm {
+	gpio-reserved-ranges = <0 4>, <8 4>;
+};
+
+&usb2 {
+	status = "okay";
+};
+
+&usb2_dwc3 {
+	dr_mode = "host";
+};
+
+&usb3 {
+	status = "okay";
+};
+
+&usb3_dwc3 {
+	dr_mode = "peripheral";
+	extcon = <&extcon_usb>;
+};
diff --git a/arch/arm64/boot/dts/qcom/sdm630-sony-xperia-nile.dtsi b/arch/arm64/boot/dts/qcom/sdm630-sony-xperia-nile.dtsi
index 11d0a8c1cf35..09c07800793a 100644
--- a/arch/arm64/boot/dts/qcom/sdm630-sony-xperia-nile.dtsi
+++ b/arch/arm64/boot/dts/qcom/sdm630-sony-xperia-nile.dtsi
@@ -10,6 +10,7 @@
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/input/gpio-keys.h>
+#include <dt-bindings/leds/common.h>
 
 / {
 	/* required for bootloader to select correct board */
@@ -34,7 +35,7 @@
 			height = <1920>;
 			stride = <(1080 * 4)>;
 			format = "a8r8g8b8";
-			status= "okay";
+			status = "okay";
 		};
 	};
 
@@ -87,14 +88,10 @@
 		pinctrl-0 = <&imx300_vana_default>;
 	};
 
-	gpio_keys {
-		status = "okay";
+	gpio-keys {
 		compatible = "gpio-keys";
-		input-name = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 
-		camera_focus {
+		key-camera-focus {
 			label = "Camera Focus";
 			gpios = <&tlmm 64 GPIO_ACTIVE_LOW>;
 			linux,input-type = <1>;
@@ -102,7 +99,7 @@
 			debounce-interval = <15>;
 		};
 
-		camera_snapshot {
+		key-camera-snapshot {
 			label = "Camera Snapshot";
 			gpios = <&tlmm 113 GPIO_ACTIVE_LOW>;
 			linux,input-type = <1>;
@@ -110,7 +107,7 @@
 			debounce-interval = <15>;
 		};
 
-		vol_down {
+		key-vol-down {
 			label = "Volume Down";
 			gpios = <&pm660l_gpios 7 GPIO_ACTIVE_LOW>;
 			linux,input-type = <1>;
@@ -215,17 +212,46 @@
 	/* HCI Bluetooth */
 };
 
-&pon {
-	volup {
-		compatible = "qcom,pm8941-resin";
-		interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>;
-		debounce = <15625>;
-		bias-pull-up;
-		linux,code = <KEY_VOLUMEUP>;
+&pm660l_lpg {
+	qcom,power-source = <1>;
+
+	status = "okay";
+
+	multi-led {
+		color = <LED_COLOR_ID_RGB>;
+		function = LED_FUNCTION_STATUS;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		led@1 {
+			reg = <1>;
+			color = <LED_COLOR_ID_BLUE>;
+		};
+
+		led@2 {
+			reg = <2>;
+			color = <LED_COLOR_ID_GREEN>;
+		};
+
+		led@3 {
+			reg = <3>;
+			color = <LED_COLOR_ID_RED>;
+		};
 	};
 };
 
-&qusb2phy {
+&pon_pwrkey {
+	status = "okay";
+};
+
+&pon_resin {
+	status = "okay";
+
+	linux,code = <KEY_VOLUMEUP>;
+};
+
+&qusb2phy0 {
 	status = "okay";
 
 	vdd-supply = <&vreg_l1b_0p925>;
@@ -550,6 +576,22 @@
 	};
 };
 
+&sdc2_state_on {
+	sd-cd {
+		pins = "gpio54";
+		bias-pull-up;
+		drive-strength = <2>;
+	};
+};
+
+&sdc2_state_off {
+	sd-cd {
+		pins = "gpio54";
+		bias-disable;
+		drive-strength = <2>;
+	};
+};
+
 &sdhc_1 {
 	status = "okay";
 	supports-cqe;
diff --git a/arch/arm64/boot/dts/qcom/sdm630.dtsi b/arch/arm64/boot/dts/qcom/sdm630.dtsi
index 3e0165bb61c5..b51b85f583e5 100644
--- a/arch/arm64/boot/dts/qcom/sdm630.dtsi
+++ b/arch/arm64/boot/dts/qcom/sdm630.dtsi
@@ -8,6 +8,7 @@
 #include <dt-bindings/clock/qcom,gpucc-sdm660.h>
 #include <dt-bindings/clock/qcom,mmcc-sdm660.h>
 #include <dt-bindings/clock/qcom,rpmcc.h>
+#include <dt-bindings/interconnect/qcom,sdm660.h>
 #include <dt-bindings/power/qcom-rpmpd.h>
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
@@ -19,6 +20,11 @@
 	#address-cells = <2>;
 	#size-cells = <2>;
 
+	aliases {
+		mmc1 = &sdhc_1;
+		mmc2 = &sdhc_2;
+	};
+
 	chosen { };
 
 	clocks {
@@ -547,19 +553,19 @@
 		};
 
 		qfprom: qfprom@780000 {
-			compatible = "qcom,qfprom";
+			compatible = "qcom,sdm630-qfprom", "qcom,qfprom";
 			reg = <0x00780000 0x621c>;
 			#address-cells = <1>;
 			#size-cells = <1>;
 
 			qusb2_hstx_trim: hstx-trim@240 {
-				reg = <0x240 0x1>;
-				bits = <25 3>;
+				reg = <0x243 0x1>;
+				bits = <1 3>;
 			};
 
 			gpu_speed_bin: gpu-speed-bin@41a0 {
-				reg = <0x41a0 0x1>;
-				bits = <21 7>;
+				reg = <0x41a2 0x1>;
+				bits = <5 7>;
 			};
 		};
 
@@ -691,9 +697,15 @@
 			#thermal-sensor-cells = <1>;
 		};
 
-		tcsr_mutex_regs: syscon@1f40000 {
-			compatible = "syscon";
-			reg = <0x01f40000 0x40000>;
+		tcsr_mutex: hwlock@1f40000 {
+			compatible = "qcom,tcsr-mutex";
+			reg = <0x01f40000 0x20000>;
+			#hwlock-cells = <1>;
+		};
+
+		tcsr_regs_1: syscon@1f60000 {
+			compatible = "qcom,sdm630-tcsr", "syscon";
+			reg = <0x01f60000 0x20000>;
 		};
 
 		tlmm: pinctrl@3100000 {
@@ -977,12 +989,6 @@
 					bias-pull-up;
 					drive-strength = <10>;
 				};
-
-				sd-cd {
-					pins = "gpio54";
-					bias-pull-up;
-					drive-strength = <2>;
-				};
 			};
 
 			sdc2_state_off: sdc2-off {
@@ -1003,18 +1009,11 @@
 					bias-pull-up;
 					drive-strength = <2>;
 				};
-
-				sd-cd {
-					pins = "gpio54";
-					bias-disable;
-					drive-strength = <2>;
-				};
 			};
 		};
 
 		adreno_gpu: gpu@5000000 {
 			compatible = "qcom,adreno-508.0", "qcom,adreno";
-			#stream-id-cells = <16>;
 
 			reg = <0x05000000 0x40000>;
 			reg-names = "kgsl_3d0_reg_memory";
@@ -1041,13 +1040,15 @@
 			nvmem-cells = <&gpu_speed_bin>;
 			nvmem-cell-names = "speed_bin";
 
-			interconnects = <&gnoc 1 &bimc 5>;
+			interconnects = <&bimc MASTER_OXILI &bimc SLAVE_EBI>;
 			interconnect-names = "gfx-mem";
 
 			operating-points-v2 = <&gpu_sdm630_opp_table>;
 
+			status = "disabled";
+
 			gpu_sdm630_opp_table: opp-table {
-				compatible  = "operating-points-v2";
+				compatible = "operating-points-v2";
 				opp-775000000 {
 					opp-hz = /bits/ 64 <775000000>;
 					opp-level = <RPM_SMD_LEVEL_TURBO>;
@@ -1211,11 +1212,15 @@
 			clocks = <&gcc GCC_CFG_NOC_USB3_AXI_CLK>,
 				 <&gcc GCC_USB30_MASTER_CLK>,
 				 <&gcc GCC_AGGRE2_USB3_AXI_CLK>,
-				 <&rpmcc RPM_SMD_AGGR2_NOC_CLK>,
+				 <&gcc GCC_USB30_SLEEP_CLK>,
 				 <&gcc GCC_USB30_MOCK_UTMI_CLK>,
-				 <&gcc GCC_USB30_SLEEP_CLK>;
-			clock-names = "cfg_noc", "core", "iface", "bus",
-				      "mock_utmi", "sleep";
+				 <&rpmcc RPM_SMD_AGGR2_NOC_CLK>;
+			clock-names = "cfg_noc",
+				      "core",
+				      "iface",
+				      "sleep",
+				      "mock_utmi",
+				      "bus";
 
 			assigned-clocks = <&gcc GCC_USB30_MOCK_UTMI_CLK>,
 					  <&gcc GCC_USB30_MASTER_CLK>,
@@ -1244,19 +1249,19 @@
 				 * haven't seen any devices making use of it.
 				 */
 				maximum-speed = "high-speed";
-				phys = <&qusb2phy>;
+				phys = <&qusb2phy0>;
 				phy-names = "usb2-phy";
 				snps,hird-threshold = /bits/ 8 <0>;
 			};
 		};
 
-		qusb2phy: phy@c012000 {
+		qusb2phy0: phy@c012000 {
 			compatible = "qcom,sdm660-qusb2-phy";
 			reg = <0x0c012000 0x180>;
 			#phy-cells = <0>;
 
 			clocks = <&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>,
-				<&gcc GCC_RX1_USB2_CLKREF_CLK>;
+				 <&gcc GCC_RX0_USB2_CLKREF_CLK>;
 			clock-names = "cfg_ahb", "ref";
 
 			resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>;
@@ -1264,7 +1269,21 @@
 			status = "disabled";
 		};
 
-		sdhc_2: sdhci@c084000 {
+		qusb2phy1: phy@c014000 {
+			compatible = "qcom,sdm660-qusb2-phy";
+			reg = <0x0c014000 0x180>;
+			#phy-cells = <0>;
+
+			clocks = <&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>,
+				 <&gcc GCC_RX1_USB2_CLKREF_CLK>;
+			clock-names = "cfg_ahb", "ref";
+
+			resets = <&gcc GCC_QUSB2PHY_SEC_BCR>;
+			nvmem-cells = <&qusb2_hstx_trim>;
+			status = "disabled";
+		};
+
+		sdhc_2: mmc@c084000 {
 			compatible = "qcom,sdm630-sdhci", "qcom,sdhci-msm-v5";
 			reg = <0x0c084000 0x1000>;
 			reg-names = "hc";
@@ -1274,13 +1293,16 @@
 			interrupt-names = "hc_irq", "pwr_irq";
 
 			bus-width = <4>;
-			clocks = <&gcc GCC_SDCC2_APPS_CLK>,
-					<&gcc GCC_SDCC2_AHB_CLK>,
+
+			clocks = <&gcc GCC_SDCC2_AHB_CLK>,
+					<&gcc GCC_SDCC2_APPS_CLK>,
 					<&xo_board>;
-			clock-names = "core", "iface", "xo";
+			clock-names = "iface", "core", "xo";
+
 
 			interconnects = <&a2noc 3 &a2noc 10>,
 					<&gnoc 0 &cnoc 28>;
+			interconnect-names = "sdhc-ddr","cpu-sdhc";
 			operating-points-v2 = <&sdhc2_opp_table>;
 
 			pinctrl-names = "default", "sleep";
@@ -1314,7 +1336,7 @@
 			};
 		};
 
-		sdhc_1: sdhci@c0c4000 {
+		sdhc_1: mmc@c0c4000 {
 			compatible = "qcom,sdm630-sdhci", "qcom,sdhci-msm-v5";
 			reg = <0x0c0c4000 0x1000>,
 			      <0x0c0c5000 0x1000>,
@@ -1325,15 +1347,15 @@
 					<GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "hc_irq", "pwr_irq";
 
-			clocks = <&gcc GCC_SDCC1_APPS_CLK>,
-				 <&gcc GCC_SDCC1_AHB_CLK>,
+			clocks = <&gcc GCC_SDCC1_AHB_CLK>,
+				 <&gcc GCC_SDCC1_APPS_CLK>,
 				 <&xo_board>,
 				 <&gcc GCC_SDCC1_ICE_CORE_CLK>;
-			clock-names = "core", "iface", "xo", "ice";
+			clock-names = "iface", "core", "xo", "ice";
 
 			interconnects = <&a2noc 2 &a2noc 10>,
 					<&gnoc 0 &cnoc 27>;
-			interconnect-names = "sdhc1-ddr", "cpu-sdhc1";
+			interconnect-names = "sdhc-ddr", "cpu-sdhc";
 			operating-points-v2 = <&sdhc1_opp_table>;
 			pinctrl-names = "default", "sleep";
 			pinctrl-0 = <&sdc1_state_on>;
@@ -1369,6 +1391,47 @@
 			};
 		};
 
+		usb2: usb@c2f8800 {
+			compatible = "qcom,sdm660-dwc3", "qcom,dwc3";
+			reg = <0x0c2f8800 0x400>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			clocks = <&gcc GCC_CFG_NOC_USB2_AXI_CLK>,
+				 <&gcc GCC_USB20_MASTER_CLK>,
+				 <&gcc GCC_USB20_MOCK_UTMI_CLK>,
+				 <&gcc GCC_USB20_SLEEP_CLK>;
+			clock-names = "cfg_noc", "core",
+				      "mock_utmi", "sleep";
+
+			assigned-clocks = <&gcc GCC_USB20_MOCK_UTMI_CLK>,
+					  <&gcc GCC_USB20_MASTER_CLK>;
+			assigned-clock-rates = <19200000>, <60000000>;
+
+			interrupts = <GIC_SPI 348 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hs_phy_irq";
+
+			qcom,select-utmi-as-pipe-clk;
+
+			resets = <&gcc GCC_USB_20_BCR>;
+
+			usb2_dwc3: usb@c200000 {
+				compatible = "snps,dwc3";
+				reg = <0x0c200000 0xc8d0>;
+				interrupts = <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>;
+				snps,dis_u2_susphy_quirk;
+				snps,dis_enblslpm_quirk;
+
+				/* This is the HS-only host */
+				maximum-speed = "high-speed";
+				phys = <&qusb2phy1>;
+				phy-names = "usb2-phy";
+				snps,hird-threshold = /bits/ 8 <0>;
+			};
+		};
+
 		mmcc: clock-controller@c8c0000 {
 			compatible = "qcom,mmcc-sdm630";
 			reg = <0x0c8c0000 0x40000>;
@@ -1397,7 +1460,7 @@
 					<0>;
 		};
 
-		dsi_opp_table: dsi-opp-table {
+		dsi_opp_table: opp-table-dsi {
 			compatible = "operating-points-v2";
 
 			opp-131250000 {
@@ -1449,7 +1512,7 @@
 				reg-names = "mdp_phys";
 
 				interrupt-parent = <&mdss>;
-				interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
+				interrupts = <0>;
 
 				assigned-clocks = <&mmcc MDSS_MDP_CLK>,
 						  <&mmcc MDSS_VSYNC_CLK>;
@@ -1486,7 +1549,7 @@
 					};
 				};
 
-				mdp_opp_table: mdp-opp {
+				mdp_opp_table: opp-table {
 					compatible = "operating-points-v2";
 
 					opp-150000000 {
@@ -1526,7 +1589,7 @@
 				power-domains = <&rpmpd SDM660_VDDCX>;
 
 				interrupt-parent = <&mdss>;
-				interrupts = <4 IRQ_TYPE_LEVEL_HIGH>;
+				interrupts = <4>;
 
 				assigned-clocks = <&mmcc BYTE0_CLK_SRC>,
 						  <&mmcc PCLK0_CLK_SRC>;
@@ -1555,6 +1618,8 @@
 				phys = <&dsi0_phy>;
 				phy-names = "dsi";
 
+				status = "disabled";
+
 				ports {
 					#address-cells = <1>;
 					#size-cells = <0>;
@@ -1588,6 +1653,7 @@
 
 				clocks = <&mmcc MDSS_AHB_CLK>, <&xo_board>;
 				clock-names = "iface", "ref";
+				status = "disabled";
 			};
 		};
 
@@ -1821,8 +1887,8 @@
 			status = "disabled";
 		};
 
-		imem@146bf000 {
-			compatible = "simple-mfd";
+		sram@146bf000 {
+			compatible = "qcom,sdm630-imem", "syscon", "simple-mfd";
 			reg = <0x146bf000 0x1000>;
 
 			#address-cells = <1>;
@@ -1838,138 +1904,138 @@
 
 		camss: camss@ca00000 {
 			compatible = "qcom,sdm660-camss";
-			reg = <0x0c824000 0x1000>,
+			reg = <0x0ca00020 0x10>,
+			      <0x0ca30000 0x100>,
+			      <0x0ca30400 0x100>,
+			      <0x0ca30800 0x100>,
+			      <0x0ca30c00 0x100>,
+			      <0x0c824000 0x1000>,
 			      <0x0ca00120 0x4>,
 			      <0x0c825000 0x1000>,
 			      <0x0ca00124 0x4>,
 			      <0x0c826000 0x1000>,
 			      <0x0ca00128 0x4>,
-			      <0x0ca30000 0x100>,
-			      <0x0ca30400 0x100>,
-			      <0x0ca30800 0x100>,
-			      <0x0ca30c00 0x100>,
 			      <0x0ca31000 0x500>,
-			      <0x0ca00020 0x10>,
 			      <0x0ca10000 0x1000>,
 			      <0x0ca14000 0x1000>;
-			reg-names = "csiphy0",
+			reg-names = "csi_clk_mux",
+				    "csid0",
+				    "csid1",
+				    "csid2",
+				    "csid3",
+				    "csiphy0",
 				    "csiphy0_clk_mux",
 				    "csiphy1",
 				    "csiphy1_clk_mux",
 				    "csiphy2",
 				    "csiphy2_clk_mux",
-				    "csid0",
-				    "csid1",
-				    "csid2",
-				    "csid3",
 				    "ispif",
-				    "csi_clk_mux",
 				    "vfe0",
 				    "vfe1";
-			interrupts = <GIC_SPI 78 IRQ_TYPE_EDGE_RISING>,
-				     <GIC_SPI 79 IRQ_TYPE_EDGE_RISING>,
-				     <GIC_SPI 80 IRQ_TYPE_EDGE_RISING>,
-				     <GIC_SPI 296 IRQ_TYPE_EDGE_RISING>,
+			interrupts = <GIC_SPI 296 IRQ_TYPE_EDGE_RISING>,
 				     <GIC_SPI 297 IRQ_TYPE_EDGE_RISING>,
 				     <GIC_SPI 298 IRQ_TYPE_EDGE_RISING>,
 				     <GIC_SPI 299 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 78 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 79 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 80 IRQ_TYPE_EDGE_RISING>,
 				     <GIC_SPI 309 IRQ_TYPE_EDGE_RISING>,
 				     <GIC_SPI 314 IRQ_TYPE_EDGE_RISING>,
 				     <GIC_SPI 315 IRQ_TYPE_EDGE_RISING>;
-			interrupt-names = "csiphy0",
-					  "csiphy1",
-					  "csiphy2",
-					  "csid0",
+			interrupt-names = "csid0",
 					  "csid1",
 					  "csid2",
 					  "csid3",
+					  "csiphy0",
+					  "csiphy1",
+					  "csiphy2",
 					  "ispif",
 					  "vfe0",
 					  "vfe1";
-			clocks = <&mmcc CAMSS_TOP_AHB_CLK>,
-				<&mmcc THROTTLE_CAMSS_AXI_CLK>,
-				<&mmcc CAMSS_ISPIF_AHB_CLK>,
-				<&mmcc CAMSS_CSI0PHYTIMER_CLK>,
-				<&mmcc CAMSS_CSI1PHYTIMER_CLK>,
-				<&mmcc CAMSS_CSI2PHYTIMER_CLK>,
-				<&mmcc CAMSS_CSI0_AHB_CLK>,
-				<&mmcc CAMSS_CSI0_CLK>,
-				<&mmcc CAMSS_CPHY_CSID0_CLK>,
-				<&mmcc CAMSS_CSI0PIX_CLK>,
-				<&mmcc CAMSS_CSI0RDI_CLK>,
-				<&mmcc CAMSS_CSI1_AHB_CLK>,
-				<&mmcc CAMSS_CSI1_CLK>,
-				<&mmcc CAMSS_CPHY_CSID1_CLK>,
-				<&mmcc CAMSS_CSI1PIX_CLK>,
-				<&mmcc CAMSS_CSI1RDI_CLK>,
-				<&mmcc CAMSS_CSI2_AHB_CLK>,
-				<&mmcc CAMSS_CSI2_CLK>,
-				<&mmcc CAMSS_CPHY_CSID2_CLK>,
-				<&mmcc CAMSS_CSI2PIX_CLK>,
-				<&mmcc CAMSS_CSI2RDI_CLK>,
-				<&mmcc CAMSS_CSI3_AHB_CLK>,
-				<&mmcc CAMSS_CSI3_CLK>,
-				<&mmcc CAMSS_CPHY_CSID3_CLK>,
-				<&mmcc CAMSS_CSI3PIX_CLK>,
-				<&mmcc CAMSS_CSI3RDI_CLK>,
-				<&mmcc CAMSS_AHB_CLK>,
-				<&mmcc CAMSS_VFE0_CLK>,
-				<&mmcc CAMSS_CSI_VFE0_CLK>,
-				<&mmcc CAMSS_VFE0_AHB_CLK>,
-				<&mmcc CAMSS_VFE0_STREAM_CLK>,
-				<&mmcc CAMSS_VFE1_CLK>,
-				<&mmcc CAMSS_CSI_VFE1_CLK>,
-				<&mmcc CAMSS_VFE1_AHB_CLK>,
-				<&mmcc CAMSS_VFE1_STREAM_CLK>,
-				<&mmcc CAMSS_VFE_VBIF_AHB_CLK>,
-				<&mmcc CAMSS_VFE_VBIF_AXI_CLK>,
-				<&mmcc CSIPHY_AHB2CRIF_CLK>,
-				<&mmcc CAMSS_CPHY_CSID0_CLK>,
-				<&mmcc CAMSS_CPHY_CSID1_CLK>,
-				<&mmcc CAMSS_CPHY_CSID2_CLK>,
-				<&mmcc CAMSS_CPHY_CSID3_CLK>;
-			clock-names = "top_ahb",
-				"throttle_axi",
-				"ispif_ahb",
-				"csiphy0_timer",
-				"csiphy1_timer",
-				"csiphy2_timer",
-				"csi0_ahb",
-				"csi0",
-				"csi0_phy",
-				"csi0_pix",
-				"csi0_rdi",
-				"csi1_ahb",
-				"csi1",
-				"csi1_phy",
-				"csi1_pix",
-				"csi1_rdi",
-				"csi2_ahb",
-				"csi2",
-				"csi2_phy",
-				"csi2_pix",
-				"csi2_rdi",
-				"csi3_ahb",
-				"csi3",
-				"csi3_phy",
-				"csi3_pix",
-				"csi3_rdi",
-				"ahb",
-				"vfe0",
-				"csi_vfe0",
-				"vfe0_ahb",
-				"vfe0_stream",
-				"vfe1",
-				"csi_vfe1",
-				"vfe1_ahb",
-				"vfe1_stream",
-				"vfe_ahb",
-				"vfe_axi",
-				"csiphy_ahb2crif",
-				"cphy_csid0",
-				"cphy_csid1",
-				"cphy_csid2",
-				"cphy_csid3";
+			clocks = <&mmcc CAMSS_AHB_CLK>,
+				 <&mmcc CAMSS_CPHY_CSID0_CLK>,
+				 <&mmcc CAMSS_CPHY_CSID1_CLK>,
+				 <&mmcc CAMSS_CPHY_CSID2_CLK>,
+				 <&mmcc CAMSS_CPHY_CSID3_CLK>,
+				 <&mmcc CAMSS_CSI0_AHB_CLK>,
+				 <&mmcc CAMSS_CSI0_CLK>,
+				 <&mmcc CAMSS_CPHY_CSID0_CLK>,
+				 <&mmcc CAMSS_CSI0PIX_CLK>,
+				 <&mmcc CAMSS_CSI0RDI_CLK>,
+				 <&mmcc CAMSS_CSI1_AHB_CLK>,
+				 <&mmcc CAMSS_CSI1_CLK>,
+				 <&mmcc CAMSS_CPHY_CSID1_CLK>,
+				 <&mmcc CAMSS_CSI1PIX_CLK>,
+				 <&mmcc CAMSS_CSI1RDI_CLK>,
+				 <&mmcc CAMSS_CSI2_AHB_CLK>,
+				 <&mmcc CAMSS_CSI2_CLK>,
+				 <&mmcc CAMSS_CPHY_CSID2_CLK>,
+				 <&mmcc CAMSS_CSI2PIX_CLK>,
+				 <&mmcc CAMSS_CSI2RDI_CLK>,
+				 <&mmcc CAMSS_CSI3_AHB_CLK>,
+				 <&mmcc CAMSS_CSI3_CLK>,
+				 <&mmcc CAMSS_CPHY_CSID3_CLK>,
+				 <&mmcc CAMSS_CSI3PIX_CLK>,
+				 <&mmcc CAMSS_CSI3RDI_CLK>,
+				 <&mmcc CAMSS_CSI0PHYTIMER_CLK>,
+				 <&mmcc CAMSS_CSI1PHYTIMER_CLK>,
+				 <&mmcc CAMSS_CSI2PHYTIMER_CLK>,
+				 <&mmcc CSIPHY_AHB2CRIF_CLK>,
+				 <&mmcc CAMSS_CSI_VFE0_CLK>,
+				 <&mmcc CAMSS_CSI_VFE1_CLK>,
+				 <&mmcc CAMSS_ISPIF_AHB_CLK>,
+				 <&mmcc THROTTLE_CAMSS_AXI_CLK>,
+				 <&mmcc CAMSS_TOP_AHB_CLK>,
+				 <&mmcc CAMSS_VFE0_AHB_CLK>,
+				 <&mmcc CAMSS_VFE0_CLK>,
+				 <&mmcc CAMSS_VFE0_STREAM_CLK>,
+				 <&mmcc CAMSS_VFE1_AHB_CLK>,
+				 <&mmcc CAMSS_VFE1_CLK>,
+				 <&mmcc CAMSS_VFE1_STREAM_CLK>,
+				 <&mmcc CAMSS_VFE_VBIF_AHB_CLK>,
+				 <&mmcc CAMSS_VFE_VBIF_AXI_CLK>;
+			clock-names = "ahb",
+				      "cphy_csid0",
+				      "cphy_csid1",
+				      "cphy_csid2",
+				      "cphy_csid3",
+				      "csi0_ahb",
+				      "csi0",
+				      "csi0_phy",
+				      "csi0_pix",
+				      "csi0_rdi",
+				      "csi1_ahb",
+				      "csi1",
+				      "csi1_phy",
+				      "csi1_pix",
+				      "csi1_rdi",
+				      "csi2_ahb",
+				      "csi2",
+				      "csi2_phy",
+				      "csi2_pix",
+				      "csi2_rdi",
+				      "csi3_ahb",
+				      "csi3",
+				      "csi3_phy",
+				      "csi3_pix",
+				      "csi3_rdi",
+				      "csiphy0_timer",
+				      "csiphy1_timer",
+				      "csiphy2_timer",
+				      "csiphy_ahb2crif",
+				      "csi_vfe0",
+				      "csi_vfe1",
+				      "ispif_ahb",
+				      "throttle_axi",
+				      "top_ahb",
+				      "vfe0_ahb",
+				      "vfe0",
+				      "vfe0_stream",
+				      "vfe1_ahb",
+				      "vfe1",
+				      "vfe1_stream",
+				      "vfe_ahb",
+				      "vfe_axi";
 			interconnects = <&mnoc 5 &bimc 5>;
 			interconnect-names = "vfe-mem";
 			iommus = <&mmss_smmu 0xc00>,
@@ -2150,13 +2216,11 @@
 				label = "lpass";
 				mboxes = <&apcs_glb 9>;
 				qcom,remote-pid = <2>;
-				#address-cells = <1>;
-				#size-cells = <0>;
 
 				apr {
 					compatible = "qcom,apr-v2";
 					qcom,glink-channels = "apr_audio_svc";
-					qcom,apr-domain = <APR_DOMAIN_ADSP>;
+					qcom,domain = <APR_DOMAIN_ADSP>;
 					#address-cells = <1>;
 					#size-cells = <0>;
 
@@ -2293,12 +2357,6 @@
 		};
 	};
 
-	tcsr_mutex: hwlock {
-		compatible = "qcom,tcsr-mutex";
-		syscon = <&tcsr_mutex_regs 0 0x1000>;
-		#hwlock-cells = <1>;
-	};
-
 	sound: sound {
 	};
 
diff --git a/arch/arm64/boot/dts/qcom/sdm632-fairphone-fp3.dts b/arch/arm64/boot/dts/qcom/sdm632-fairphone-fp3.dts
new file mode 100644
index 000000000000..891e314bc782
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sdm632-fairphone-fp3.dts
@@ -0,0 +1,183 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2022, Luca Weiss <luca@z3ntu.xyz>
+ */
+/dts-v1/;
+
+#include "sdm632.dtsi"
+#include "pm8953.dtsi"
+
+/ {
+	model = "Fairphone 3";
+	compatible = "fairphone,fp3", "qcom,sdm632";
+	chassis-type = "handset";
+	qcom,msm-id = <349 0>;
+	qcom,board-id = <8 0x10000>;
+
+	aliases {
+		mmc0 = &sdhc_1;
+		mmc1 = &sdhc_2;
+		serial0 = &uart_0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		key-volume-up {
+			label = "volume_up";
+			linux,code = <KEY_VOLUMEUP>;
+			gpios = <&tlmm 85 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	vph_pwr: vph-pwr-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vph_pwr";
+		regulator-always-on;
+		regulator-boot-on;
+	};
+};
+
+&hsusb_phy {
+	status = "okay";
+	vdd-supply = <&pm8953_l3>;
+	vdda-pll-supply = <&pm8953_l7>;
+	vdda-phy-dpdm-supply = <&pm8953_l13>;
+};
+
+&pm8953_resin {
+	status = "okay";
+	linux,code = <KEY_VOLUMEDOWN>;
+};
+
+&sdhc_1 {
+	status = "okay";
+	vmmc-supply = <&pm8953_l8>;
+	vqmmc-supply = <&pm8953_l5>;
+};
+
+&sdhc_2 {
+	status = "okay";
+	vmmc-supply = <&pm8953_l11>;
+	vqmmc-supply = <&pm8953_l12>;
+
+	cd-gpios = <&tlmm 133 GPIO_ACTIVE_LOW>;
+};
+
+&rpm_requests {
+	pm8953-regulators {
+		compatible = "qcom,rpm-pm8953-regulators";
+
+		vdd_l1-supply = <&pm8953_s3>;
+		vdd_l2_l3-supply = <&pm8953_s3>;
+		vdd_l4_l5_l6_l7_l16_l19-supply = <&pm8953_s4>;
+		vdd_l8_l11_l12_l13_l14_l15-supply = <&vph_pwr>;
+		vdd_l9_l10_l17_l18_l22-supply = <&vph_pwr>;
+
+		pm8953_s3: s3 {
+			regulator-min-microvolt = <984000>;
+			regulator-max-microvolt = <1240000>;
+		};
+		pm8953_s4: s4 {
+			regulator-min-microvolt = <1036000>;
+			regulator-max-microvolt = <2040000>;
+		};
+		pm8953_s5: s5 {
+			regulator-min-microvolt = <1036000>;
+			regulator-max-microvolt = <2040000>;
+		};
+
+		pm8953_l1: l1 {
+			regulator-min-microvolt = <975000>;
+			regulator-max-microvolt = <1050000>;
+		};
+		pm8953_l2: l2 {
+			regulator-min-microvolt = <975000>;
+			regulator-max-microvolt = <1175000>;
+		};
+		pm8953_l3: l3 {
+			regulator-min-microvolt = <925000>;
+			regulator-max-microvolt = <925000>;
+		};
+		pm8953_l5: l5 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+		pm8953_l6: l6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+		pm8953_l7: l7 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1900000>;
+		};
+		pm8953_l8: l8 {
+			regulator-min-microvolt = <2900000>;
+			regulator-max-microvolt = <2900000>;
+		};
+		pm8953_l9: l9 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3300000>;
+		};
+		pm8953_l10: l10 {
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <3000000>;
+		};
+		pm8953_l11: l11 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+		};
+		pm8953_l12: l12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+		pm8953_l13: l13 {
+			regulator-min-microvolt = <3125000>;
+			regulator-max-microvolt = <3125000>;
+		};
+		pm8953_l16: l16 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+		pm8953_l17: l17 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <2850000>;
+		};
+		pm8953_l19: l19 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1350000>;
+		};
+		pm8953_l22: l22 {
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+		};
+		pm8953_l23: l23 {
+			regulator-min-microvolt = <975000>;
+			regulator-max-microvolt = <1225000>;
+		};
+	};
+};
+
+&tlmm {
+	/*
+	 * 0-3: unused but protected by TZ
+	 * 135-138: fingerprint reader (SPI)
+	 */
+	gpio-reserved-ranges = <0 4>, <135 4>;
+};
+
+&uart_0 {
+	status = "okay";
+};
+
+&usb3 {
+	status = "okay";
+};
+
+&usb3_dwc3 {
+	dr_mode = "peripheral";
+};
diff --git a/arch/arm64/boot/dts/qcom/sdm632.dtsi b/arch/arm64/boot/dts/qcom/sdm632.dtsi
new file mode 100644
index 000000000000..645b9f6a801f
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sdm632.dtsi
@@ -0,0 +1,81 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/* Copyright (c) 2022, The Linux Foundation. All rights reserved. */
+
+#include "msm8953.dtsi"
+
+/ {
+	thermal-zones {
+		/delete-node/cpu1-thermal;
+		/delete-node/cpu2-thermal;
+		/delete-node/cpu3-thermal;
+
+		cpu0-thermal {
+			thermal-sensors = <&tsens0 13>;
+
+			cooling-maps {
+				map0 {
+					cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&CPU1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&CPU2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&CPU3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+
+		cpu4-thermal {
+			thermal-sensors = <&tsens0 5>;
+		};
+
+		cpu5-thermal {
+			thermal-sensors = <&tsens0 6>;
+		};
+
+		cpu6-thermal {
+			thermal-sensors = <&tsens0 7>;
+		};
+
+		cpu7-thermal {
+			thermal-sensors = <&tsens0 8>;
+		};
+	};
+};
+
+/*
+ * SDM632 uses Kryo 250 instead of Cortex A53
+ * CPU0-3 are efficiency cores, CPU4-7 are performance cores
+ */
+&CPU0 {
+	compatible = "qcom,kryo250";
+};
+
+&CPU1 {
+	compatible = "qcom,kryo250";
+};
+
+&CPU2 {
+	compatible = "qcom,kryo250";
+};
+
+&CPU3 {
+	compatible = "qcom,kryo250";
+};
+
+&CPU4 {
+	compatible = "qcom,kryo250";
+	capacity-dmips-mhz = <1980>;
+};
+
+&CPU5 {
+	compatible = "qcom,kryo250";
+	capacity-dmips-mhz = <1980>;
+};
+
+&CPU6 {
+	compatible = "qcom,kryo250";
+	capacity-dmips-mhz = <1980>;
+};
+
+&CPU7 {
+	compatible = "qcom,kryo250";
+	capacity-dmips-mhz = <1980>;
+};
diff --git a/arch/arm64/boot/dts/qcom/sdm636-sony-xperia-ganges-mermaid.dts b/arch/arm64/boot/dts/qcom/sdm636-sony-xperia-ganges-mermaid.dts
index bba1c2bce213..58f687fc49e0 100644
--- a/arch/arm64/boot/dts/qcom/sdm636-sony-xperia-ganges-mermaid.dts
+++ b/arch/arm64/boot/dts/qcom/sdm636-sony-xperia-ganges-mermaid.dts
@@ -11,6 +11,7 @@
 / {
 	model = "Sony Xperia 10 Plus";
 	compatible = "sony,mermaid-row", "qcom,sdm636";
+	chassis-type = "handset";
 
 	/* SDM636 v1 */
 	qcom,msm-id = <345 0>;
@@ -18,7 +19,7 @@
 };
 
 &sdc2_state_on {
-	pinconf-clk {
+	clk {
 		drive-strength = <14>;
 	};
 };
diff --git a/arch/arm64/boot/dts/qcom/sdm660-xiaomi-lavender.dts b/arch/arm64/boot/dts/qcom/sdm660-xiaomi-lavender.dts
index 1edc53fd6941..a3559f6e34a5 100644
--- a/arch/arm64/boot/dts/qcom/sdm660-xiaomi-lavender.dts
+++ b/arch/arm64/boot/dts/qcom/sdm660-xiaomi-lavender.dts
@@ -1,11 +1,16 @@
 // SPDX-License-Identifier: GPL-2.0-only
 /*
  * Copyright (c) 2020, Alexey Minnekhanov <alexey.min@gmail.com>
+ * Copyright (c) 2021, Dang Huynh <danct12@riseup.net>
  */
 
 /dts-v1/;
 
 #include "sdm660.dtsi"
+#include "pm660.dtsi"
+#include "pm660l.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/input/gpio-keys.h>
 
 / {
 	model = "Xiaomi Redmi Note 7";
@@ -17,7 +22,41 @@
 	};
 
 	chosen {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
 		stdout-path = "serial0:115200n8";
+
+		framebuffer0: framebuffer@9d400000 {
+			compatible = "simple-framebuffer";
+			reg = <0 0x9d400000 0 (1080 * 2340 * 4)>;
+			width = <1080>;
+			height = <2340>;
+			stride = <(1080 * 4)>;
+			format = "a8r8g8b8";
+		};
+	};
+
+	vph_pwr: vph-pwr-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vph_pwr";
+		regulator-min-microvolt = <3700000>;
+		regulator-max-microvolt = <3700000>;
+
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		key-volup {
+			label = "Volume Up";
+			gpios = <&pm660l_gpios 7 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+			debounce-interval = <15>;
+		};
 	};
 
 	reserved-memory {
@@ -33,6 +72,20 @@
 			ftrace-size = <0x0>;
 			pmsg-size = <0x20000>;
 		};
+
+		framebuffer_mem: memory@9d400000 {
+			reg = <0x0 0x9d400000 0x0 0x23ff000>;
+			no-map;
+		};
+	};
+
+	/*
+	 * Until we hook up type-c detection, we
+	 * have to stick with this. But it works.
+	 */
+	extcon_usb: extcon-usb {
+		compatible = "linux,extcon-usb-gpio";
+		id-gpio = <&tlmm 58 GPIO_ACTIVE_HIGH>;
 	};
 };
 
@@ -40,6 +93,328 @@
 	status = "okay";
 };
 
+&pon_pwrkey {
+	status = "okay";
+};
+
+&pon_resin {
+	status = "okay";
+
+	linux,code = <KEY_VOLUMEDOWN>;
+};
+
+&qusb2phy0 {
+	status = "okay";
+
+	vdd-supply = <&vreg_l1b_0p925>;
+	vdda-phy-dpdm-supply = <&vreg_l7b_3p125>;
+};
+
+&rpm_requests {
+	pm660l-regulators {
+		compatible = "qcom,rpm-pm660l-regulators";
+
+		vdd_s1-supply = <&vph_pwr>;
+		vdd_s2-supply = <&vph_pwr>;
+		vdd_s3_s4-supply = <&vph_pwr>;
+		vdd_s5-supply = <&vph_pwr>;
+		vdd_s6-supply = <&vph_pwr>;
+
+		vdd_l1_l9_l10-supply = <&vreg_s2b_1p05>;
+		vdd_l2-supply = <&vreg_bob>;
+		vdd_l3_l5_l7_l8-supply = <&vreg_bob>;
+		vdd_l4_l6-supply = <&vreg_bob>;
+		vdd_bob-supply = <&vph_pwr>;
+
+		vreg_s1b_1p125: s1 {
+			regulator-min-microvolt = <1125000>;
+			regulator-max-microvolt = <1125000>;
+			regulator-enable-ramp-delay = <200>;
+		};
+
+		vreg_s2b_1p05: s2 {
+			regulator-min-microvolt = <1050000>;
+			regulator-max-microvolt = <1050000>;
+			regulator-enable-ramp-delay = <200>;
+		};
+
+		/* LDOs */
+		vreg_l1b_0p925: l1 {
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <925000>;
+			regulator-enable-ramp-delay = <250>;
+			regulator-allow-set-load;
+		};
+
+		/* SDHCI 3.3V signal doesn't seem to be supported. */
+		vreg_l2b_2p95: l2 {
+			regulator-min-microvolt = <1648000>;
+			regulator-max-microvolt = <2696000>;
+			regulator-enable-ramp-delay = <250>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l3b_3p3: l3 {
+			regulator-min-microvolt = <1700000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-enable-ramp-delay = <250>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l4b_2p95: l4 {
+			regulator-min-microvolt = <2944000>;
+			regulator-max-microvolt = <2952000>;
+			regulator-enable-ramp-delay = <250>;
+
+			regulator-min-microamp = <200>;
+			regulator-max-microamp = <600000>;
+			regulator-system-load = <570000>;
+			regulator-allow-set-load;
+		};
+
+		/*
+		 * Downstream specifies a range of 1721-3600mV,
+		 * but the only assigned consumers are SDHCI2 VMMC
+		 * and Coresight QPDI that both request pinned 2.95V.
+		 * Tighten the range to 1.8-3.328 (closest to 3.3) to
+		 * make the mmc driver happy.
+		 */
+		vreg_l5b_2p95: l5 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <3328000>;
+			regulator-enable-ramp-delay = <250>;
+			regulator-allow-set-load;
+			regulator-system-load = <800000>;
+		};
+
+		vreg_l7b_3p125: l7 {
+			regulator-min-microvolt = <2700000>;
+			regulator-max-microvolt = <3125000>;
+			regulator-enable-ramp-delay = <250>;
+		};
+
+		vreg_l8b_3p3: l8 {
+			regulator-min-microvolt = <3200000>;
+			regulator-max-microvolt = <3400000>;
+			regulator-enable-ramp-delay = <250>;
+		};
+
+		vreg_bob: bob {
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3600000>;
+			regulator-enable-ramp-delay = <500>;
+		};
+	};
+
+	pm660-regulators {
+		compatible = "qcom,rpm-pm660-regulators";
+
+		vdd_s1-supply = <&vph_pwr>;
+		vdd_s2-supply = <&vph_pwr>;
+		vdd_s3-supply = <&vph_pwr>;
+		vdd_s4-supply = <&vph_pwr>;
+		vdd_s5-supply = <&vph_pwr>;
+		vdd_s6-supply = <&vph_pwr>;
+
+		vdd_l1_l6_l7-supply = <&vreg_s5a_1p35>;
+		vdd_l2_l3-supply = <&vreg_s2b_1p05>;
+		vdd_l5-supply = <&vreg_s2b_1p05>;
+		vdd_l8_l9_l10_l11_l12_l13_l14-supply = <&vreg_s4a_2p04>;
+		vdd_l15_l16_l17_l18_l19-supply = <&vreg_bob>;
+
+		/*
+		 * S1A (FTAPC0), S2A (FTAPC1), S3A (HFAPC1) are managed
+		 * by the Core Power Reduction hardened (CPRh) and the
+		 * Operating State Manager (OSM) HW automatically.
+		 */
+
+		vreg_s4a_2p04: s4 {
+			regulator-min-microvolt = <1805000>;
+			regulator-max-microvolt = <2040000>;
+			regulator-enable-ramp-delay = <200>;
+			regulator-always-on;
+		};
+
+		vreg_s5a_1p35: s5 {
+			regulator-min-microvolt = <1224000>;
+			regulator-max-microvolt = <1350000>;
+			regulator-enable-ramp-delay = <200>;
+		};
+
+		vreg_s6a_0p87: s6 {
+			regulator-min-microvolt = <504000>;
+			regulator-max-microvolt = <992000>;
+			regulator-enable-ramp-delay = <150>;
+		};
+
+		/* LDOs */
+		vreg_l1a_1p225: l1 {
+			regulator-min-microvolt = <1150000>;
+			regulator-max-microvolt = <1250000>;
+			regulator-enable-ramp-delay = <250>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l2a_1p0: l2 {
+			regulator-min-microvolt = <950000>;
+			regulator-max-microvolt = <1010000>;
+			regulator-enable-ramp-delay = <250>;
+		};
+
+		vreg_l3a_1p0: l3 {
+			regulator-min-microvolt = <950000>;
+			regulator-max-microvolt = <1010000>;
+			regulator-enable-ramp-delay = <250>;
+		};
+
+		vreg_l5a_0p848: l5 {
+			regulator-min-microvolt = <525000>;
+			regulator-max-microvolt = <950000>;
+			regulator-enable-ramp-delay = <250>;
+		};
+
+		vreg_l6a_1p3: l6 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1370000>;
+			regulator-allow-set-load;
+			regulator-enable-ramp-delay = <250>;
+		};
+
+		vreg_l7a_1p2: l7 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-enable-ramp-delay = <250>;
+		};
+
+		vreg_l8a_1p8: l8 {
+			regulator-min-microvolt = <1750000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-enable-ramp-delay = <250>;
+			regulator-system-load = <325000>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l9a_1p8: l9 {
+			regulator-min-microvolt = <1750000>;
+			regulator-max-microvolt = <1900000>;
+			regulator-enable-ramp-delay = <250>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l10a_1p8: l10 {
+			regulator-min-microvolt = <1780000>;
+			regulator-max-microvolt = <1950000>;
+			regulator-enable-ramp-delay = <250>;
+			regulator-allow-set-load;
+		};
+
+		vreg_l11a_1p8: l11 {
+			regulator-min-microvolt = <1780000>;
+			regulator-max-microvolt = <1950000>;
+			regulator-enable-ramp-delay = <250>;
+		};
+
+		vreg_l12a_1p8: l12 {
+			regulator-min-microvolt = <1780000>;
+			regulator-max-microvolt = <1950000>;
+			regulator-enable-ramp-delay = <250>;
+		};
+
+		/* This gives power to the LPDDR4: never turn it off! */
+		vreg_l13a_1p8: l13 {
+			regulator-min-microvolt = <1780000>;
+			regulator-max-microvolt = <1950000>;
+			regulator-enable-ramp-delay = <250>;
+			regulator-boot-on;
+			regulator-always-on;
+		};
+
+		vreg_l14a_1p8: l14 {
+			regulator-min-microvolt = <1710000>;
+			regulator-max-microvolt = <1900000>;
+			regulator-enable-ramp-delay = <250>;
+		};
+
+		vreg_l15a_1p8: l15 {
+			regulator-min-microvolt = <1650000>;
+			regulator-max-microvolt = <2950000>;
+			regulator-enable-ramp-delay = <250>;
+		};
+
+		vreg_l16a_2p7: l16 {
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+			regulator-enable-ramp-delay = <250>;
+			regulator-always-on;
+		};
+
+		vreg_l17a_1p8: l17 {
+			regulator-min-microvolt = <1648000>;
+			regulator-max-microvolt = <2952000>;
+			regulator-enable-ramp-delay = <250>;
+		};
+
+		vreg_l19a_3p3: l19 {
+			regulator-min-microvolt = <3312000>;
+			regulator-max-microvolt = <3400000>;
+			regulator-enable-ramp-delay = <250>;
+			regulator-allow-set-load;
+		};
+	};
+};
+
+&pm660l_wled {
+	status = "okay";
+
+	qcom,switching-freq = <800>;
+	qcom,current-limit-microamp = <20000>;
+	qcom,num-strings = <2>;
+};
+
+&sdc2_state_on {
+	sd-cd {
+		pins = "gpio54";
+		bias-pull-up;
+		drive-strength = <2>;
+	};
+};
+
+&sdc2_state_off {
+	sd-cd {
+		pins = "gpio54";
+		bias-disable;
+		drive-strength = <2>;
+	};
+};
+
+&sdhc_1 {
+	status = "okay";
+	supports-cqe;
+
+	mmc-hs200-1_8v;
+	mmc-hs400-1_8v;
+	mmc-hs400-enhanced-strobe;
+
+	vmmc-supply = <&vreg_l4b_2p95>;
+	vqmmc-supply = <&vreg_l8a_1p8>;
+};
+
+&sdhc_2 {
+	status = "okay";
+
+	vmmc-supply = <&vreg_l5b_2p95>;
+	vqmmc-supply = <&vreg_l2b_2p95>;
+};
+
 &tlmm {
 	gpio-reserved-ranges = <8 4>;
 };
+
+&usb3 {
+	status = "okay";
+};
+
+&usb3_dwc3 {
+	dr_mode = "peripheral";
+	extcon = <&extcon_usb>;
+};
diff --git a/arch/arm64/boot/dts/qcom/sdm660.dtsi b/arch/arm64/boot/dts/qcom/sdm660.dtsi
index eccf6fde16b4..43220af1b685 100644
--- a/arch/arm64/boot/dts/qcom/sdm660.dtsi
+++ b/arch/arm64/boot/dts/qcom/sdm660.dtsi
@@ -14,7 +14,7 @@
 	operating-points-v2 = <&gpu_sdm660_opp_table>;
 
 	gpu_sdm660_opp_table: opp-table {
-		compatible  = "operating-points-v2";
+		compatible = "operating-points-v2";
 
 		/*
 		 * 775MHz is only available on the highest speed bin
@@ -163,7 +163,7 @@
 		power-domains = <&rpmpd SDM660_VDDCX>;
 
 		interrupt-parent = <&mdss>;
-		interrupts = <5 IRQ_TYPE_LEVEL_HIGH>;
+		interrupts = <5>;
 
 		assigned-clocks = <&mmcc BYTE1_CLK_SRC>,
 					<&mmcc PCLK1_CLK_SRC>;
@@ -192,6 +192,8 @@
 		phys = <&dsi1_phy>;
 		phy-names = "dsi";
 
+		status = "disabled";
+
 		ports {
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -225,6 +227,7 @@
 
 		clocks = <&mmcc MDSS_AHB_CLK>, <&rpmcc RPM_SMD_XO_CLK_SRC>;
 		clock-names = "iface", "ref";
+		status = "disabled";
 	};
 };
 
diff --git a/arch/arm64/boot/dts/qcom/sdm845-cheza.dtsi b/arch/arm64/boot/dts/qcom/sdm845-cheza.dtsi
index 4a6285a25f77..b5eb8f7eca1d 100644
--- a/arch/arm64/boot/dts/qcom/sdm845-cheza.dtsi
+++ b/arch/arm64/boot/dts/qcom/sdm845-cheza.dtsi
@@ -119,7 +119,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pen_eject_odl>;
 
-		pen-insert {
+		switch-pen-insert {
 			label = "Pen Insert";
 			/* Insert = low, eject = high */
 			gpios = <&tlmm 119 GPIO_ACTIVE_LOW>;
@@ -130,7 +130,7 @@
 	};
 
 	panel: panel {
-		compatible ="innolux,p120zdg-bf1";
+		compatible = "innolux,p120zdg-bf1";
 		power-supply = <&pp3300_dx_edp>;
 		backlight = <&backlight>;
 		no-hpd;
@@ -145,6 +145,138 @@
 	};
 };
 
+&psci {
+	/delete-node/ cpu0;
+	/delete-node/ cpu1;
+	/delete-node/ cpu2;
+	/delete-node/ cpu3;
+	/delete-node/ cpu4;
+	/delete-node/ cpu5;
+	/delete-node/ cpu6;
+	/delete-node/ cpu7;
+	/delete-node/ cpu-cluster0;
+};
+
+&cpus {
+	/delete-node/ domain-idle-states;
+};
+
+&cpu_idle_states {
+	LITTLE_CPU_SLEEP_0: cpu-sleep-0-0 {
+		compatible = "arm,idle-state";
+		idle-state-name = "little-power-down";
+		arm,psci-suspend-param = <0x40000003>;
+		entry-latency-us = <350>;
+		exit-latency-us = <461>;
+		min-residency-us = <1890>;
+		local-timer-stop;
+	};
+
+	LITTLE_CPU_SLEEP_1: cpu-sleep-0-1 {
+		compatible = "arm,idle-state";
+		idle-state-name = "little-rail-power-down";
+		arm,psci-suspend-param = <0x40000004>;
+		entry-latency-us = <360>;
+		exit-latency-us = <531>;
+		min-residency-us = <3934>;
+		local-timer-stop;
+	};
+
+	BIG_CPU_SLEEP_0: cpu-sleep-1-0 {
+		compatible = "arm,idle-state";
+		idle-state-name = "big-power-down";
+		arm,psci-suspend-param = <0x40000003>;
+		entry-latency-us = <264>;
+		exit-latency-us = <621>;
+		min-residency-us = <952>;
+		local-timer-stop;
+	};
+
+	BIG_CPU_SLEEP_1: cpu-sleep-1-1 {
+		compatible = "arm,idle-state";
+		idle-state-name = "big-rail-power-down";
+		arm,psci-suspend-param = <0x40000004>;
+		entry-latency-us = <702>;
+		exit-latency-us = <1061>;
+		min-residency-us = <4488>;
+		local-timer-stop;
+	};
+
+	CLUSTER_SLEEP_0: cluster-sleep-0 {
+		compatible = "arm,idle-state";
+		idle-state-name = "cluster-power-down";
+		arm,psci-suspend-param = <0x400000F4>;
+		entry-latency-us = <3263>;
+		exit-latency-us = <6562>;
+		min-residency-us = <9987>;
+		local-timer-stop;
+	};
+};
+
+&CPU0 {
+	/delete-property/ power-domains;
+	/delete-property/ power-domain-names;
+	cpu-idle-states = <&LITTLE_CPU_SLEEP_0
+			   &LITTLE_CPU_SLEEP_1
+			   &CLUSTER_SLEEP_0>;
+};
+
+&CPU1 {
+	/delete-property/ power-domains;
+	/delete-property/ power-domain-names;
+	cpu-idle-states = <&LITTLE_CPU_SLEEP_0
+			   &LITTLE_CPU_SLEEP_1
+			   &CLUSTER_SLEEP_0>;
+};
+
+&CPU2 {
+	/delete-property/ power-domains;
+	/delete-property/ power-domain-names;
+	cpu-idle-states = <&LITTLE_CPU_SLEEP_0
+			   &LITTLE_CPU_SLEEP_1
+			   &CLUSTER_SLEEP_0>;
+};
+
+&CPU3 {
+	/delete-property/ power-domains;
+	/delete-property/ power-domain-names;
+	cpu-idle-states = <&LITTLE_CPU_SLEEP_0
+			   &LITTLE_CPU_SLEEP_1
+			   &CLUSTER_SLEEP_0>;
+};
+
+&CPU4 {
+	/delete-property/ power-domains;
+	/delete-property/ power-domain-names;
+	cpu-idle-states = <&BIG_CPU_SLEEP_0
+			   &BIG_CPU_SLEEP_1
+			   &CLUSTER_SLEEP_0>;
+};
+
+&CPU5 {
+	/delete-property/ power-domains;
+	/delete-property/ power-domain-names;
+	cpu-idle-states = <&BIG_CPU_SLEEP_0
+			   &BIG_CPU_SLEEP_1
+			   &CLUSTER_SLEEP_0>;
+};
+
+&CPU6 {
+	/delete-property/ power-domains;
+	/delete-property/ power-domain-names;
+	cpu-idle-states = <&BIG_CPU_SLEEP_0
+			   &BIG_CPU_SLEEP_1
+			   &CLUSTER_SLEEP_0>;
+};
+
+&CPU7 {
+	/delete-property/ power-domains;
+	/delete-property/ power-domain-names;
+	cpu-idle-states = <&BIG_CPU_SLEEP_0
+			   &BIG_CPU_SLEEP_1
+			   &CLUSTER_SLEEP_0>;
+};
+
 /*
  * Reserved memory changes
  *
@@ -708,7 +840,7 @@ ap_ts_i2c: &i2c14 {
 		pinctrl-0 = <&ec_ap_int_l>;
 		spi-max-frequency = <3000000>;
 
-		cros_ec_pwm: ec-pwm {
+		cros_ec_pwm: pwm {
 			compatible = "google,cros-ec-pwm";
 			#pwm-cells = <1>;
 		};
diff --git a/arch/arm64/boot/dts/qcom/sdm845-db845c.dts b/arch/arm64/boot/dts/qcom/sdm845-db845c.dts
index 13f80a0b6faa..132417e2d11e 100644
--- a/arch/arm64/boot/dts/qcom/sdm845-db845c.dts
+++ b/arch/arm64/boot/dts/qcom/sdm845-db845c.dts
@@ -5,6 +5,7 @@
 
 /dts-v1/;
 
+#include <dt-bindings/leds/common.h>
 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
 #include <dt-bindings/sound/qcom,q6afe.h>
@@ -28,6 +29,13 @@
 		stdout-path = "serial0:115200n8";
 	};
 
+	/* Fixed crystal oscillator dedicated to MCP2517FD */
+	clk40M: can-clock {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <40000000>;
+	};
+
 	dc12v: dc12v-regulator {
 		compatible = "regulator-fixed";
 		regulator-name = "DC12V";
@@ -36,14 +44,14 @@
 		regulator-always-on;
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 		autorepeat;
 
 		pinctrl-names = "default";
 		pinctrl-0 = <&vol_up_pin_a>;
 
-		vol-up {
+		key-vol-up {
 			label = "Volume Up";
 			linux,code = <KEY_VOLUMEUP>;
 			gpios = <&pm8998_gpio 6 GPIO_ACTIVE_LOW>;
@@ -53,22 +61,28 @@
 	leds {
 		compatible = "gpio-leds";
 
-		user4 {
+		led-0 {
 			label = "green:user4";
+			function = LED_FUNCTION_INDICATOR;
+			color = <LED_COLOR_ID_GREEN>;
 			gpios = <&pm8998_gpio 13 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "panic-indicator";
 			default-state = "off";
 		};
 
-		wlan {
+		led-1 {
 			label = "yellow:wlan";
+			function = LED_FUNCTION_WLAN;
+			color = <LED_COLOR_ID_YELLOW>;
 			gpios = <&pm8998_gpio 9 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "phy0tx";
 			default-state = "off";
 		};
 
-		bt {
+		led-2 {
 			label = "blue:bt";
+			function = LED_FUNCTION_BLUETOOTH;
+			color = <LED_COLOR_ID_BLUE>;
 			gpios = <&pm8998_gpio 5 GPIO_ACTIVE_HIGH>;
 			linux,default-trigger = "bluetooth-power";
 			default-state = "off";
@@ -425,6 +439,14 @@
 	status = "okay";
 };
 
+&gpi_dma0 {
+	status = "okay";
+};
+
+&gpi_dma1 {
+	status = "okay";
+};
+
 &gpu {
 	status = "okay";
 	zap-shader {
@@ -477,12 +499,14 @@
 
 &i2c11 {
 	/* On Low speed expansion */
+	clock-frequency = <100000>;
 	label = "LS-I2C1";
 	status = "okay";
 };
 
 &i2c14 {
 	/* On Low speed expansion */
+	clock-frequency = <100000>;
 	label = "LS-I2C0";
 	status = "okay";
 };
@@ -498,7 +522,7 @@
 
 &pcie0 {
 	status = "okay";
-	perst-gpio = <&tlmm 35 GPIO_ACTIVE_LOW>;
+	perst-gpios = <&tlmm 35 GPIO_ACTIVE_LOW>;
 	enable-gpio = <&tlmm 134 GPIO_ACTIVE_HIGH>;
 
 	vddpe-3v3-supply = <&pcie0_3p3v_dual>;
@@ -516,7 +540,7 @@
 
 &pcie1 {
 	status = "okay";
-	perst-gpio = <&tlmm 102 GPIO_ACTIVE_LOW>;
+	perst-gpios = <&tlmm 102 GPIO_ACTIVE_LOW>;
 
 	pinctrl-names = "default";
 	pinctrl-0 = <&pcie1_default_state>;
@@ -558,7 +582,7 @@
 		"OPTION2",
 		"PM845_SLB";
 
-	cam0_dvdd_1v2_en_default: cam0-dvdd-1v2-en {
+	cam0_dvdd_1v2_en_default: cam0-dvdd-1v2-en-state {
 		pins = "gpio12";
 		function = "normal";
 
@@ -567,7 +591,7 @@
 		qcom,drive-strength = <PMIC_GPIO_STRENGTH_HIGH>;
 	};
 
-	cam0_avdd_2v8_en_default: cam0-avdd-2v8-en {
+	cam0_avdd_2v8_en_default: cam0-avdd-2v8-en-state {
 		pins = "gpio10";
 		function = "normal";
 
@@ -576,7 +600,7 @@
 		qcom,drive-strength = <PMIC_GPIO_STRENGTH_HIGH>;
 	};
 
-	vol_up_pin_a: vol-up-active {
+	vol_up_pin_a: vol-up-active-state {
 		pins = "gpio6";
 		function = "normal";
 		input-enable;
@@ -595,10 +619,40 @@
 	};
 };
 
+&pmi8998_lpg {
+	status = "okay";
+
+	qcom,power-source = <1>;
+
+	led@3 {
+		reg = <3>;
+		color = <LED_COLOR_ID_GREEN>;
+		function = LED_FUNCTION_HEARTBEAT;
+		function-enumerator = <3>;
+
+		linux,default-trigger = "heartbeat";
+		default-state = "on";
+	};
+
+	led@4 {
+		reg = <4>;
+		color = <LED_COLOR_ID_GREEN>;
+		function = LED_FUNCTION_INDICATOR;
+		function-enumerator = <2>;
+	};
+
+	led@5 {
+		reg = <5>;
+		color = <LED_COLOR_ID_GREEN>;
+		function = LED_FUNCTION_INDICATOR;
+		function-enumerator = <1>;
+	};
+};
+
 /* QUAT I2S Uses 4 I2S SD Lines for audio on LT9611 HDMI Bridge */
 &q6afedai {
 	qi2s@22 {
-		reg = <22>;
+		reg = <QUATERNARY_MI2S_RX>;
 		qcom,sd-lines = <0 1 2 3>;
 	};
 };
@@ -707,7 +761,7 @@
 		};
 
 		codec {
-			sound-dai =  <&lt9611_codec 0>;
+			sound-dai = <&lt9611_codec 0>;
 		};
 	};
 
@@ -722,7 +776,7 @@
 		};
 
 		codec {
-			sound-dai =  <&left_spkr>, <&right_spkr>, <&swm 0>, <&wcd9340 0>;
+			sound-dai = <&left_spkr>, <&right_spkr>, <&swm 0>, <&wcd9340 0>;
 		};
 	};
 
@@ -742,6 +796,23 @@
 	};
 };
 
+&spi0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&qup_spi0_default>;
+	cs-gpios = <&tlmm 3 GPIO_ACTIVE_LOW>;
+
+	can@0 {
+		compatible = "microchip,mcp2517fd";
+		reg = <0>;
+		clocks = <&clk40M>;
+		interrupts-extended = <&tlmm 104 IRQ_TYPE_LEVEL_LOW>;
+		spi-max-frequency = <10000000>;
+		vdd-supply = <&vdc_5v>;
+		xceiver-supply = <&vdc_5v>;
+	};
+};
+
 &spi2 {
 	/* On Low speed expansion */
 	label = "LS-SPI0";
@@ -1010,7 +1081,7 @@
 	pinctrl-names = "default";
 	clock-names = "extclk";
 	clocks = <&rpmhcc RPMH_LN_BB_CLK2>;
-	reset-gpios = <&tlmm 64 0>;
+	reset-gpios = <&tlmm 64 GPIO_ACTIVE_HIGH>;
 	vdd-buck-supply = <&vreg_s4a_1p8>;
 	vdd-buck-sido-supply = <&vreg_s4a_1p8>;
 	vdd-tx-supply = <&vreg_s4a_1p8>;
@@ -1047,6 +1118,7 @@
 	vdd-3.3-ch0-supply = <&vreg_l25a_3p3>;
 
 	qcom,snoc-host-cap-8bit-quirk;
+	qcom,ath10k-calibration-variant = "Thundercomm_DB845C";
 };
 
 /* PINCTRL - additions to nodes defined in sdm845.dtsi */
@@ -1115,7 +1187,8 @@
 };
 
 &camss {
-	vdda-supply = <&vreg_l1a_0p875>;
+	vdda-phy-supply = <&vreg_l1a_0p875>;
+	vdda-pll-supply = <&vreg_l26a_1p2>;
 
 	status = "ok";
 
@@ -1125,7 +1198,6 @@
 		port@0 {
 			reg = <0>;
 			csiphy0_ep: endpoint {
-				clock-lanes = <7>;
 				data-lanes = <0 1 2 3>;
 				remote-endpoint = <&ov8856_ep>;
 			};
@@ -1142,8 +1214,6 @@
 		reset-gpios = <&tlmm 9 GPIO_ACTIVE_LOW>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&cam0_default>;
-		gpios = <&tlmm 13 0>,
-			<&tlmm 9 GPIO_ACTIVE_LOW>;
 
 		clocks = <&clock_camcc CAM_CC_MCLK0_CLK>;
 		clock-names = "xvclk";
@@ -1156,8 +1226,6 @@
 		 * both have to be enabled through the power management
 		 * gpios.
 		 */
-		power-domains = <&clock_camcc TITAN_TOP_GDSC>;
-
 		dovdd-supply = <&vreg_lvs1a_1p8>;
 		avdd-supply = <&cam0_avdd_2v8>;
 		dvdd-supply = <&cam0_dvdd_1v2>;
@@ -1166,7 +1234,6 @@
 
 		port {
 			ov8856_ep: endpoint {
-				clock-lanes = <1>;
 				link-frequencies = /bits/ 64
 					<360000000 180000000>;
 				data-lanes = <1 2 3 4>;
@@ -1184,11 +1251,9 @@
 		reg = <0x60>;
 
 		// CAM3_RST_N
-		enable-gpios = <&tlmm 21 0>;
+		enable-gpios = <&tlmm 21 GPIO_ACTIVE_HIGH>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&cam3_default>;
-		gpios = <&tlmm 16 0>,
-			<&tlmm 21 0>;
 
 		clocks = <&clock_camcc CAM_CC_MCLK3_CLK>;
 		clock-names = "xclk";
@@ -1202,8 +1267,6 @@
 		 *
 		 * No 1.2V vddd-supply regulator is used.
 		 */
-		power-domains = <&clock_camcc TITAN_TOP_GDSC>;
-
 		vdddo-supply = <&vreg_lvs1a_1p8>;
 		vdda-supply = <&cam3_avdd_2v8>;
 
@@ -1211,10 +1274,17 @@
 
 		port {
 			ov7251_ep: endpoint {
-				clock-lanes = <1>;
 				data-lanes = <0 1>;
 //				remote-endpoint = <&csiphy3_ep>;
 			};
 		};
 	};
 };
+
+/* PINCTRL - additions to nodes defined in sdm845.dtsi */
+&qup_spi0_default {
+	config {
+		drive-strength = <6>;
+		bias-disable;
+	};
+};
diff --git a/arch/arm64/boot/dts/qcom/sdm845-lg-common.dtsi b/arch/arm64/boot/dts/qcom/sdm845-lg-common.dtsi
new file mode 100644
index 000000000000..20f275f8694d
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sdm845-lg-common.dtsi
@@ -0,0 +1,614 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * SDM845 LG G7 / V35 (judyln / judyp) common device tree
+ *
+ * Copyright (c) 2022, The Linux Foundation. All rights reserved.
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+
+#include "sdm845.dtsi"
+#include "pm8998.dtsi"
+#include "pmi8998.dtsi"
+
+/delete-node/ &adsp_mem;
+/delete-node/ &cdsp_mem;
+/delete-node/ &gpu_mem;
+/delete-node/ &ipa_fw_mem;
+/delete-node/ &mba_region;
+/delete-node/ &mpss_region;
+/delete-node/ &qseecom_mem;
+/delete-node/ &rmtfs_mem;
+/delete-node/ &slpi_mem;
+/delete-node/ &spss_mem;
+/delete-node/ &venus_mem;
+/delete-node/ &wlan_msa_mem;
+
+/ {
+	chosen {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		qseecom_mem: memory@b2000000 {
+			reg = <0 0xb2000000 0 0x1800000>;
+			no-map;
+		};
+
+		gpu_mem: memory@8c415000 {
+			reg = <0 0x8c415000 0 0x2000>;
+			no-map;
+		};
+
+		ipa_fw_mem: memory@8c400000 {
+			reg = <0 0x8c400000 0 0x10000>;
+			no-map;
+		};
+
+		adsp_mem: memory@8c500000 {
+			reg = <0 0x8c500000 0 0x1e00000>;
+			no-map;
+		};
+
+		wlan_msa_mem: memory@8e300000 {
+			reg = <0 0x8e300000 0 0x100000>;
+			no-map;
+		};
+
+		mpss_region: memory@8e400000 {
+			reg = <0 0x8e400000 0 0x8900000>;
+			no-map;
+		};
+
+		venus_mem: memory@96d00000 {
+			reg = <0 0x96d00000 0 0x500000>;
+			no-map;
+		};
+
+		cdsp_mem: memory@97200000 {
+			reg = <0 0x97200000 0 0x800000>;
+			no-map;
+		};
+
+		mba_region: memory@97a00000 {
+			reg = <0 0x97a00000 0 0x200000>;
+			no-map;
+		};
+
+		slpi_mem: memory@97c00000 {
+			reg = <0 0x97c00000 0 0x1400000>;
+			no-map;
+		};
+
+		spss_mem: memory@99000000 {
+			reg = <0 0x99000000 0 0x100000>;
+			no-map;
+		};
+
+		/* Framebuffer region */
+		memory@9d400000 {
+			reg = <0x0 0x9d400000 0x0 0x2400000>;
+			no-map;
+		};
+
+		/* rmtfs lower guard */
+		memory@f0800000 {
+			reg = <0 0xf0800000 0 0x1000>;
+			no-map;
+		};
+
+		rmtfs_mem: memory@f0801000 {
+			compatible = "qcom,rmtfs-mem";
+			reg = <0 0xf0801000 0 0x200000>;
+			no-map;
+
+			qcom,client-id = <1>;
+			qcom,vmid = <15>;
+		};
+
+		/* rmtfs upper guard */
+		memory@f0a01000 {
+			reg = <0 0xf0a01000 0 0x1000>;
+			no-map;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&vol_up_pin_a>;
+
+		label = "GPIO Buttons";
+
+		key-vol-up {
+			label = "Volume up";
+			linux,code = <KEY_VOLUMEUP>;
+			gpios = <&pm8998_gpio 6 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	vph_pwr: vph-pwr-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vph_pwr";
+		regulator-min-microvolt = <3700000>;
+		regulator-max-microvolt = <3700000>;
+	};
+
+	/*
+	 * Apparently RPMh does not provide support for PM8998 S4 because it
+	 * is always-on; model it as a fixed regulator.
+	 */
+	vreg_s4a_1p8: pm8998-smps4-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vreg_s4a_1p8";
+
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+
+		regulator-always-on;
+		regulator-boot-on;
+
+		vin-supply = <&vph_pwr>;
+	};
+};
+
+&adsp_pas {
+	status = "okay";
+};
+
+&apps_rsc {
+	pm8998-rpmh-regulators {
+		compatible = "qcom,pm8998-rpmh-regulators";
+		qcom,pmic-id = "a";
+
+		vdd-s1-supply = <&vph_pwr>;
+		vdd-s2-supply = <&vph_pwr>;
+		vdd-s3-supply = <&vph_pwr>;
+		vdd-s4-supply = <&vph_pwr>;
+		vdd-s5-supply = <&vph_pwr>;
+		vdd-s6-supply = <&vph_pwr>;
+		vdd-s7-supply = <&vph_pwr>;
+		vdd-s8-supply = <&vph_pwr>;
+		vdd-s9-supply = <&vph_pwr>;
+		vdd-s10-supply = <&vph_pwr>;
+		vdd-s11-supply = <&vph_pwr>;
+		vdd-s12-supply = <&vph_pwr>;
+		vdd-s13-supply = <&vph_pwr>;
+		vdd-l1-l27-supply = <&vreg_s7a_1p025>;
+		vdd-l2-l8-l17-supply = <&vreg_s3a_1p35>;
+		vdd-l3-l11-supply = <&vreg_s7a_1p025>;
+		vdd-l4-l5-supply = <&vreg_s7a_1p025>;
+		vdd-l6-supply = <&vph_pwr>;
+		vdd-l7-l12-l14-l15-supply = <&vreg_s5a_2p04>;
+		vdd-l9-supply = <&vreg_bob>;
+		vdd-l10-l23-l25-supply = <&vreg_bob>;
+		vdd-l13-l19-l21-supply = <&vreg_bob>;
+		vdd-l16-l28-supply = <&vreg_bob>;
+		vdd-l18-l22-supply = <&vreg_bob>;
+		vdd-l20-l24-supply = <&vreg_bob>;
+		vdd-l26-supply = <&vreg_s3a_1p35>;
+		vin-lvs-1-2-supply = <&vreg_s4a_1p8>;
+
+		vreg_s2a_1p125: smps2 {
+			regulator-min-microvolt = <1100000>;
+			regulator-max-microvolt = <1100000>;
+		};
+
+		vreg_s3a_1p35: smps3 {
+			regulator-min-microvolt = <1352000>;
+			regulator-max-microvolt = <1352000>;
+		};
+
+		vreg_s5a_2p04: smps5 {
+			regulator-min-microvolt = <1904000>;
+			regulator-max-microvolt = <2040000>;
+		};
+
+		vreg_s7a_1p025: smps7 {
+			regulator-min-microvolt = <900000>;
+			regulator-max-microvolt = <1028000>;
+		};
+
+		vdd_qusb_hs0:
+		vdda_hp_pcie_core:
+		vdda_mipi_csi0_0p9:
+		vdda_mipi_csi1_0p9:
+		vdda_mipi_csi2_0p9:
+		vdda_mipi_dsi0_pll:
+		vdda_mipi_dsi1_pll:
+		vdda_qlink_lv:
+		vdda_qlink_lv_ck:
+		vdda_qrefs_0p875:
+		vdda_pcie_core:
+		vdda_pll_cc_ebi01:
+		vdda_pll_cc_ebi23:
+		vdda_sp_sensor:
+		vdda_ufs1_core:
+		vdda_ufs2_core:
+		vdda_usb1_ss_core:
+		vdda_usb2_ss_core:
+		vreg_l1a_0p875: ldo1 {
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <880000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vddpx_10:
+		vreg_l2a_1p2: ldo2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-always-on;
+		};
+
+		vreg_l3a_1p0: ldo3 {
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1000000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vdd_wcss_cx:
+		vdd_wcss_mx:
+		vdda_wcss_pll:
+		vreg_l5a_0p8: ldo5 {
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vddpx_13:
+		vreg_l6a_1p8: ldo6 {
+			regulator-min-microvolt = <1856000>;
+			regulator-max-microvolt = <1856000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l7a_1p8: ldo7 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l8a_1p2: ldo8 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1248000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l9a_1p8: ldo9 {
+			regulator-min-microvolt = <1704000>;
+			regulator-max-microvolt = <2928000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l10a_1p8: ldo10 {
+			regulator-min-microvolt = <1704000>;
+			regulator-max-microvolt = <2928000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l11a_1p0: ldo11 {
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1048000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vdd_qfprom:
+		vdd_qfprom_sp:
+		vdda_apc1_cs_1p8:
+		vdda_gfx_cs_1p8:
+		vdda_qrefs_1p8:
+		vdda_qusb_hs0_1p8:
+		vddpx_11:
+		vreg_l12a_1p8: ldo12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vddpx_2:
+		vreg_l13a_2p95: ldo13 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l14a_1p88: ldo14 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1880000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l15a_1p8: ldo15 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l17a_1p3: ldo17 {
+			regulator-min-microvolt = <1304000>;
+			regulator-max-microvolt = <1304000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l18a_2p7: ldo18 {
+			regulator-min-microvolt = <2704000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l20a_2p95: ldo20 {
+			regulator-min-microvolt = <2704000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l21a_2p95: ldo21 {
+			regulator-min-microvolt = <2704000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l22a_2p85: ldo22 {
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l23a_3p3: ldo23 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3312000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vdda_qusb_hs0_3p1:
+		vreg_l24a_3p075: ldo24 {
+			regulator-min-microvolt = <3088000>;
+			regulator-max-microvolt = <3088000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l25a_3p3: ldo25 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3312000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vdda_hp_pcie_1p2:
+		vdda_hv_ebi0:
+		vdda_hv_ebi1:
+		vdda_hv_ebi2:
+		vdda_hv_ebi3:
+		vdda_mipi_csi_1p25:
+		vdda_mipi_dsi0_1p2:
+		vdda_mipi_dsi1_1p2:
+		vdda_pcie_1p2:
+		vdda_ufs1_1p2:
+		vdda_ufs2_1p2:
+		vdda_usb1_ss_1p2:
+		vdda_usb2_ss_1p2:
+		vreg_l26a_1p2: ldo26 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l28a_3p0: ldo28 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_lvs1a_1p8: lvs1 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		vreg_lvs2a_1p8: lvs2 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+	};
+
+	pmi8998-rpmh-regulators {
+		compatible = "qcom,pmi8998-rpmh-regulators";
+		qcom,pmic-id = "b";
+
+		vdd-bob-supply = <&vph_pwr>;
+
+		vreg_bob: bob {
+			regulator-min-microvolt = <3312000>;
+			regulator-max-microvolt = <3600000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>;
+			regulator-allow-bypass;
+		};
+	};
+
+	pm8005-rpmh-regulators {
+		compatible = "qcom,pm8005-rpmh-regulators";
+		qcom,pmic-id = "c";
+
+		vdd-s1-supply = <&vph_pwr>;
+		vdd-s2-supply = <&vph_pwr>;
+		vdd-s3-supply = <&vph_pwr>;
+		vdd-s4-supply = <&vph_pwr>;
+
+		vreg_s3c_0p6: smps3 {
+			regulator-min-microvolt = <600000>;
+			regulator-max-microvolt = <600000>;
+		};
+	};
+};
+
+&cdsp_pas {
+	status = "okay";
+};
+
+&dispcc {
+	status = "disabled";
+};
+
+&gcc {
+	protected-clocks = <GCC_QSPI_CORE_CLK>,
+			   <GCC_QSPI_CORE_CLK_SRC>,
+			   <GCC_QSPI_CNOC_PERIPH_AHB_CLK>,
+			   <GCC_LPASS_Q6_AXI_CLK>,
+			   <GCC_LPASS_SWAY_CLK>;
+};
+
+&gpu {
+	status = "okay";
+
+	zap-shader {
+		memory-region = <&gpu_mem>;
+	};
+};
+
+&ipa {
+	status = "okay";
+	modem-init;
+};
+
+&mss_pil {
+	status = "okay";
+};
+
+&pm8998_pon {
+	resin {
+		compatible = "qcom,pm8941-resin";
+		interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>;
+		debounce = <15625>;
+		bias-pull-up;
+		linux,code = <KEY_VOLUMEDOWN>;
+	};
+};
+
+&sdhc_2 {
+	status = "okay";
+
+	cd-gpios = <&tlmm 126 GPIO_ACTIVE_LOW>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdc2_clk &sdc2_cmd &sdc2_data &sd_card_det_n>;
+
+	vmmc-supply = <&vreg_l21a_2p95>;
+	vqmmc-supply = <&vddpx_2>;
+};
+
+/*
+ * UFS works partially and only with clk_ignore_unused.
+ * Sometimes it crashes with I/O errors.
+ */
+&ufs_mem_hc {
+	status = "okay";
+
+	reset-gpios = <&tlmm 150 GPIO_ACTIVE_LOW>;
+
+	vcc-supply = <&vreg_l20a_2p95>;
+	vcc-max-microamp = <600000>;
+};
+
+&ufs_mem_phy {
+	status = "okay";
+
+	vdda-phy-supply = <&vdda_ufs1_core>;
+	vdda-pll-supply = <&vdda_ufs1_1p2>;
+};
+
+&usb_1 {
+	status = "okay";
+};
+
+&usb_1_dwc3 {
+	/* TODO: these devices have usb id pin */
+	dr_mode = "peripheral";
+};
+
+&usb_1_hsphy {
+	status = "okay";
+
+	vdd-supply = <&vdda_usb1_ss_core>;
+	vdda-pll-supply = <&vdda_qusb_hs0_1p8>;
+	vdda-phy-dpdm-supply = <&vdda_qusb_hs0_3p1>;
+
+	qcom,imp-res-offset-value = <8>;
+	qcom,hstx-trim-value = <QUSB2_V2_HSTX_TRIM_21_6_MA>;
+	qcom,preemphasis-level = <QUSB2_V2_PREEMPHASIS_5_PERCENT>;
+	qcom,preemphasis-width = <QUSB2_V2_PREEMPHASIS_WIDTH_HALF_BIT>;
+};
+
+&usb_1_qmpphy {
+	status = "okay";
+
+	vdda-phy-supply = <&vdda_usb1_ss_1p2>;
+	vdda-pll-supply = <&vdda_usb1_ss_core>;
+};
+
+/* PINCTRL - additions to nodes defined in sdm845.dtsi */
+
+&tlmm {
+	gpio-reserved-ranges = <28 4>, <81 4>;
+
+	sdc2_clk: sdc2-clk {
+		pinconf {
+			pins = "sdc2_clk";
+			bias-disable;
+
+			/*
+			 * It seems that mmc_test reports errors if drive
+			 * strength is not 16 on clk, cmd, and data pins.
+			 *
+			 * TODO: copy-pasted from mtp, try other values
+			 * on these devices.
+			 */
+			drive-strength = <16>;
+		};
+	};
+
+	sdc2_cmd: sdc2-cmd {
+		pinconf {
+			pins = "sdc2_cmd";
+			bias-pull-up;
+			drive-strength = <16>;
+		};
+	};
+
+	sdc2_data: sdc2-data {
+		pinconf {
+			pins = "sdc2_data";
+			bias-pull-up;
+			drive-strength = <16>;
+		};
+	};
+
+	sd_card_det_n: sd-card-det-n {
+		pinmux {
+			pins = "gpio126";
+			function = "gpio";
+		};
+
+		pinconf {
+			pins = "gpio126";
+			bias-pull-up;
+		};
+	};
+};
+
+&pm8998_gpio {
+	vol_up_pin_a: vol-up-active-pins {
+		pins = "gpio6";
+		function = "normal";
+		input-enable;
+		bias-pull-up;
+		qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
+	};
+};
diff --git a/arch/arm64/boot/dts/qcom/sdm845-lg-judyln.dts b/arch/arm64/boot/dts/qcom/sdm845-lg-judyln.dts
new file mode 100644
index 000000000000..7d967a104b3e
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sdm845-lg-judyln.dts
@@ -0,0 +1,68 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * SDM845 LG G7 (judyln) device tree.
+ *
+ * Copyright (c) 2022, The Linux Foundation. All rights reserved.
+ */
+
+/dts-v1/;
+
+#include "sdm845-lg-common.dtsi"
+
+/ {
+	model = "LG G7 ThinQ";
+	compatible = "lg,judyln", "qcom,sdm845";
+
+	chosen {
+		framebuffer@9d400000 {
+			compatible = "simple-framebuffer";
+			reg = <0x0 0x9d400000 0x0 (1440 * 3120 * 4)>;
+			width = <1440>;
+			height = <3120>;
+			stride = <(1440 * 4)>;
+			format = "a8r8g8b8";
+			lab-supply = <&lab>;
+			ibb-supply = <&ibb>;
+		};
+	};
+
+	/* Additional ThinQ key */
+	gpio-keys {
+		pinctrl-0 = <&vol_up_pin_a &thinq_key_default>;
+
+		key-thinq {
+			label = "ThinQ";
+			linux,code = <KEY_ASSISTANT>;
+			interrupt-parent = <&tlmm>;
+			interrupts = <89 IRQ_TYPE_LEVEL_LOW>;
+		};
+	};
+};
+
+&adsp_pas {
+	firmware-name = "qcom/sdm845/judyln/adsp.mbn";
+};
+
+&cdsp_pas {
+	firmware-name = "qcom/sdm845/judyln/cdsp.mbn";
+};
+
+&gpu {
+	zap-shader {
+		firmware-name = "qcom/sdm845/judyln/a630_zap.mbn";
+	};
+};
+
+&mss_pil {
+	firmware-name = "qcom/sdm845/judyln/mba.mbn", "qcom/sdm845/judyln/modem.mbn";
+};
+
+&tlmm {
+	thinq_key_default: thinq-key-default {
+		pins = "gpio89";
+		function = "gpio";
+
+		drive-strength = <2>;
+		bias-pull-up;
+	};
+};
diff --git a/arch/arm64/boot/dts/qcom/sdm845-lg-judyp.dts b/arch/arm64/boot/dts/qcom/sdm845-lg-judyp.dts
new file mode 100644
index 000000000000..d17d4d4d5609
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sdm845-lg-judyp.dts
@@ -0,0 +1,44 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * SDM845 LG V35 (judyp) device tree.
+ *
+ * Copyright (c) 2022, The Linux Foundation. All rights reserved.
+ */
+
+/dts-v1/;
+
+#include "sdm845-lg-common.dtsi"
+
+/ {
+	model = "LG V35 ThinQ";
+	compatible = "lg,judyp", "qcom,sdm845";
+
+	chosen {
+		framebuffer@9d400000 {
+			compatible = "simple-framebuffer";
+			reg = <0x0 0x9d400000 0x0 (1440 * 2880 * 4)>;
+			width = <1440>;
+			height = <2880>;
+			stride = <(1440 * 4)>;
+			format = "a8r8g8b8";
+		};
+	};
+};
+
+&adsp_pas {
+	firmware-name = "qcom/sdm845/judyp/adsp.mbn";
+};
+
+&cdsp_pas {
+	firmware-name = "qcom/sdm845/judyp/cdsp.mbn";
+};
+
+&gpu {
+	zap-shader {
+		firmware-name = "qcom/sdm845/judyp/a630_zap.mbn";
+	};
+};
+
+&mss_pil {
+	firmware-name = "qcom/sdm845/judyp/mba.mbn", "qcom/sdm845/judyp/modem.mbn";
+};
diff --git a/arch/arm64/boot/dts/qcom/sdm845-mtp.dts b/arch/arm64/boot/dts/qcom/sdm845-mtp.dts
index 5e6e8f4fb5be..de2d10e0315a 100644
--- a/arch/arm64/boot/dts/qcom/sdm845-mtp.dts
+++ b/arch/arm64/boot/dts/qcom/sdm845-mtp.dts
@@ -9,6 +9,8 @@
 
 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
 #include "sdm845.dtsi"
+#include "pm8998.dtsi"
+#include "pmi8998.dtsi"
 
 / {
 	model = "Qualcomm Technologies, Inc. SDM845 MTP";
@@ -45,6 +47,68 @@
 
 		vin-supply = <&vph_pwr>;
 	};
+
+	thermal-zones {
+		xo_thermal: xo-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+
+			thermal-sensors = <&pm8998_adc_tm 1>;
+
+			trips {
+				trip-point {
+					temperature = <125000>;
+					hysteresis = <10000>;
+					type = "passive";
+				};
+			};
+		};
+
+		msm_thermal: msm-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+
+			thermal-sensors = <&pm8998_adc_tm 2>;
+
+			trips {
+				trip-point {
+					temperature = <125000>;
+					hysteresis = <10000>;
+					type = "passive";
+				};
+			};
+		};
+
+		pa_thermal: pa-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+
+			thermal-sensors = <&pm8998_adc_tm 3>;
+
+			trips {
+				trip-point {
+					temperature = <125000>;
+					hysteresis = <10000>;
+					type = "passive";
+				};
+			};
+		};
+
+		quiet_thermal: quiet-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+
+			thermal-sensors = <&pm8998_adc_tm 4>;
+
+			trips {
+				trip-point {
+					temperature = <125000>;
+					hysteresis = <10000>;
+					type = "passive";
+				};
+			};
+		};
+	};
 };
 
 &adsp_pas {
@@ -467,6 +531,82 @@
 	firmware-name = "qcom/sdm845/mba.mbn", "qcom/sdm845/modem.mbn";
 };
 
+&pm8998_adc {
+	adc-chan@4c {
+		reg = <ADC5_XO_THERM_100K_PU>;
+		label = "xo_therm";
+		qcom,ratiometric;
+		qcom,hw-settle-time = <200>;
+	};
+
+	adc-chan@4d {
+		reg = <ADC5_AMUX_THM1_100K_PU>;
+		label = "msm_therm";
+		qcom,ratiometric;
+		qcom,hw-settle-time = <200>;
+	};
+
+	adc-chan@4f {
+		reg = <ADC5_AMUX_THM3_100K_PU>;
+		label = "pa_therm1";
+		qcom,ratiometric;
+		qcom,hw-settle-time = <200>;
+	};
+
+	adc-chan@51 {
+		reg = <ADC5_AMUX_THM5_100K_PU>;
+		label = "quiet_therm";
+		qcom,ratiometric;
+		qcom,hw-settle-time = <200>;
+	};
+
+	adc-chan@83 {
+		reg = <ADC5_VPH_PWR>;
+		label = "vph_pwr";
+		qcom,ratiometric;
+		qcom,hw-settle-time = <200>;
+	};
+
+	adc-chan@85 {
+		reg = <ADC5_VCOIN>;
+		label = "vcoin";
+		qcom,ratiometric;
+		qcom,hw-settle-time = <200>;
+	};
+};
+
+&pm8998_adc_tm {
+	status = "okay";
+
+	xo-thermistor@1 {
+		reg = <1>;
+		io-channels = <&pm8998_adc ADC5_XO_THERM_100K_PU>;
+		qcom,ratiometric;
+		qcom,hw-settle-time-us = <200>;
+	};
+
+	msm-thermistor@2 {
+		reg = <2>;
+		io-channels = <&pm8998_adc ADC5_AMUX_THM1_100K_PU>;
+		qcom,ratiometric;
+		qcom,hw-settle-time-us = <200>;
+	};
+
+	pa-thermistor@3 {
+		reg = <3>;
+		io-channels = <&pm8998_adc ADC5_AMUX_THM3_100K_PU>;
+		qcom,ratiometric;
+		qcom,hw-settle-time-us = <200>;
+	};
+
+	quiet-thermistor@4 {
+		reg = <4>;
+		io-channels = <&pm8998_adc ADC5_AMUX_THM5_100K_PU>;
+		qcom,ratiometric;
+		qcom,hw-settle-time-us = <200>;
+	};
+};
+
 &qupv3_id_1 {
 	status = "okay";
 };
diff --git a/arch/arm64/boot/dts/qcom/sdm845-oneplus-common.dtsi b/arch/arm64/boot/dts/qcom/sdm845-oneplus-common.dtsi
index 3e04aeb479d1..392461c29e76 100644
--- a/arch/arm64/boot/dts/qcom/sdm845-oneplus-common.dtsi
+++ b/arch/arm64/boot/dts/qcom/sdm845-oneplus-common.dtsi
@@ -34,14 +34,14 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&volume_down_gpio &volume_up_gpio>;
 
-		vol-down {
+		key-vol-down {
 			label = "Volume down";
 			linux,code = <KEY_VOLUMEDOWN>;
 			gpios = <&pm8998_gpio 5 GPIO_ACTIVE_LOW>;
 			debounce-interval = <15>;
 		};
 
-		vol-up {
+		key-vol-up {
 			label = "Volume up";
 			linux,code = <KEY_VOLUMEUP>;
 			gpios = <&pm8998_gpio 6 GPIO_ACTIVE_LOW>;
@@ -54,7 +54,7 @@
 		 * it is otherwise possible for an allocation adjacent to the
 		 * rmtfs_mem region to trigger an XPU violation, causing a crash.
 		 */
-		rmtfs_lower_guard: memory@f5b00000 {
+		rmtfs_lower_guard: rmtfs-lower-guard@f5b00000 {
 			no-map;
 			reg = <0 0xf5b00000 0 0x1000>;
 		};
@@ -63,7 +63,7 @@
 		 * but given the same address every time. Hard code it as this address is
 		 * where the modem firmware expects it to be.
 		 */
-		rmtfs_mem: memory@f5b01000 {
+		rmtfs_mem: rmtfs-mem@f5b01000 {
 			compatible = "qcom,rmtfs-mem";
 			reg = <0 0xf5b01000 0 0x200000>;
 			no-map;
@@ -71,7 +71,7 @@
 			qcom,client-id = <1>;
 			qcom,vmid = <15>;
 		};
-		rmtfs_upper_guard: memory@f5d01000 {
+		rmtfs_upper_guard: rmtfs-upper-guard@f5d01000 {
 			no-map;
 			reg = <0 0xf5d01000 0 0x1000>;
 		};
@@ -80,7 +80,7 @@
 		 * It seems like reserving the old rmtfs_mem region is also needed to prevent
 		 * random crashes which are most likely modem related, more testing needed.
 		 */
-		removed_region: memory@88f00000 {
+		removed_region: removed-region@88f00000 {
 			no-map;
 			reg = <0 0x88f00000 0 0x1c00000>;
 		};
@@ -376,6 +376,17 @@
 	};
 };
 
+&i2c10 {
+	status = "okay";
+	clock-frequency = <100000>;
+
+	bq27441_fg: bq27441-battery@55 {
+		compatible = "ti,bq27411";
+		status = "okay";
+		reg = <0x55>;
+	};
+};
+
 &i2c12 {
 	status = "okay";
 	clock-frequency = <400000>;
@@ -429,7 +440,7 @@
 };
 
 &pm8998_gpio {
-	volume_down_gpio: pm8998_gpio5 {
+	volume_down_gpio: pm8998-gpio5-state {
 		pinconf {
 			pins = "gpio5";
 			function = "normal";
@@ -439,7 +450,7 @@
 		};
 	};
 
-	volume_up_gpio: pm8998_gpio6 {
+	volume_up_gpio: pm8998-gpio6-state {
 		pinconf {
 			pins = "gpio6";
 			function = "normal";
@@ -619,7 +630,7 @@
 			pins = "gpio6", "gpio25", "gpio26";
 			function = "gpio";
 			drive-strength = <8>;
-			bias-disable = <0>;
+			bias-disable;
 		};
 	};
 
@@ -646,6 +657,7 @@
 
 &venus {
 	status = "okay";
+	firmware-name = "qcom/sdm845/oneplus6/venus.mbn";
 };
 
 &wifi {
diff --git a/arch/arm64/boot/dts/qcom/sdm845-oneplus-enchilada.dts b/arch/arm64/boot/dts/qcom/sdm845-oneplus-enchilada.dts
index 73493079d13e..bf2cf92e8976 100644
--- a/arch/arm64/boot/dts/qcom/sdm845-oneplus-enchilada.dts
+++ b/arch/arm64/boot/dts/qcom/sdm845-oneplus-enchilada.dts
@@ -11,6 +11,16 @@
 	model = "OnePlus 6";
 	compatible = "oneplus,enchilada", "qcom,sdm845";
 	chassis-type = "handset";
+	qcom,msm-id = <0x141 0x20001>;
+	qcom,board-id = <8 0 17819 22>;
+
+	battery: battery {
+		compatible = "simple-battery";
+
+		charge-full-design-microamp-hours = <3300000>;
+		voltage-min-design-microvolt = <3400000>;
+		voltage-max-design-microvolt = <4400000>;
+	};
 };
 
 &display_panel {
@@ -18,3 +28,7 @@
 
 	compatible = "samsung,sofef00";
 };
+
+&bq27441_fg {
+	monitored-battery = <&battery>;
+};
diff --git a/arch/arm64/boot/dts/qcom/sdm845-oneplus-fajita.dts b/arch/arm64/boot/dts/qcom/sdm845-oneplus-fajita.dts
index b63ebc48f62f..1b6b5bf368df 100644
--- a/arch/arm64/boot/dts/qcom/sdm845-oneplus-fajita.dts
+++ b/arch/arm64/boot/dts/qcom/sdm845-oneplus-fajita.dts
@@ -11,6 +11,16 @@
 	model = "OnePlus 6T";
 	compatible = "oneplus,fajita", "qcom,sdm845";
 	chassis-type = "handset";
+	qcom,msm-id = <0x141 0x20001>;
+	qcom,board-id = <8 0 18801 41>;
+
+	battery: battery {
+		compatible = "simple-battery";
+
+		charge-full-design-microamp-hours = <3700000>;
+		voltage-min-design-microvolt = <3400000>;
+		voltage-max-design-microvolt = <4400000>;
+	};
 };
 
 &display_panel {
@@ -19,6 +29,10 @@
 	compatible = "samsung,s6e3fc2x01";
 };
 
+&bq27441_fg {
+	monitored-battery = <&battery>;
+};
+
 &rmi4_f12 {
 	touchscreen-y-mm = <148>;
 };
diff --git a/arch/arm64/boot/dts/qcom/sdm845-shift-axolotl.dts b/arch/arm64/boot/dts/qcom/sdm845-shift-axolotl.dts
new file mode 100644
index 000000000000..83261c9bb4f2
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sdm845-shift-axolotl.dts
@@ -0,0 +1,765 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2022, Alexander Martinz <amartinz@shiftphones.com>
+ * Copyright (c) 2022, Caleb Connolly <caleb@connolly.tech>
+ * Copyright (c) 2022, Dylan Van Assche <me@dylanvanassche.be>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+#include "sdm845.dtsi"
+#include "pm8998.dtsi"
+#include "pmi8998.dtsi"
+
+/ {
+	model = "SHIFT SHIFT6mq";
+	compatible = "shift,axolotl", "qcom,sdm845";
+	qcom,msm-id = <321 0x20001>;
+	qcom,board-id = <11 0>;
+
+	aliases {
+		display0 = &framebuffer0;
+		serial0 = &uart9;
+	};
+
+	chosen {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		stdout-path = "serial0";
+
+		/* Use framebuffer setup by the bootloader. */
+		framebuffer0: framebuffer@9d400000 {
+			compatible = "simple-framebuffer";
+			reg = <0x0 0x9d400000 0x0 (1080 * 2160 * 4)>;
+			width = <1080>;
+			height = <2160>;
+			stride = <(1080 * 4)>;
+			format = "a8r8g8b8";
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		autorepeat;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&volume_up_gpio>;
+
+		key-vol-up {
+			label = "volume_up";
+			linux,code = <KEY_VOLUMEUP>;
+			gpios = <&pm8998_gpio 6 GPIO_ACTIVE_LOW>;
+			debounce-interval = <15>;
+		};
+	};
+
+	reserved-memory {
+		framebuffer_region@9d400000 {
+			reg = <0x0 0x9d400000 0x0 (1080 * 2160 * 4)>;
+			no-map;
+		};
+
+		ramoops: ramoops@b0000000 {
+			compatible = "ramoops";
+			reg = <0 0xb0000000 0 0x00400000>;
+			record-size = <0x40000>;
+			console-size = <0x40000>;
+			ftrace-size = <0x40000>;
+			pmsg-size = <0x200000>;
+			ecc-size = <0x0>;
+		};
+	};
+
+	battery: battery {
+		compatible = "simple-battery";
+
+		charge-full-design-microamp-hours = <3850000>;
+		voltage-min-design-microvolt = <3600000>;
+		voltage-max-design-microvolt = <4400000>;
+	};
+
+	vph_pwr: vph-pwr-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vph_pwr";
+		regulator-min-microvolt = <3700000>;
+		regulator-max-microvolt = <3700000>;
+	};
+
+	vreg_s4a_1p8: pm8998-smps4 {
+		compatible = "regulator-fixed";
+		regulator-name = "vreg_s4a_1p8";
+
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+
+		regulator-always-on;
+		regulator-boot-on;
+
+		vin-supply = <&vph_pwr>;
+	};
+};
+
+&adsp_pas {
+	status = "okay";
+	firmware-name = "qcom/sdm845/axolotl/adsp.mbn";
+};
+
+&apps_rsc {
+	pm8998-rpmh-regulators {
+		compatible = "qcom,pm8998-rpmh-regulators";
+		qcom,pmic-id = "a";
+
+		vdd-s1-supply = <&vph_pwr>;
+		vdd-s2-supply = <&vph_pwr>;
+		vdd-s3-supply = <&vph_pwr>;
+		vdd-s4-supply = <&vph_pwr>;
+		vdd-s5-supply = <&vph_pwr>;
+		vdd-s6-supply = <&vph_pwr>;
+		vdd-s7-supply = <&vph_pwr>;
+		vdd-s8-supply = <&vph_pwr>;
+		vdd-s9-supply = <&vph_pwr>;
+		vdd-s10-supply = <&vph_pwr>;
+		vdd-s11-supply = <&vph_pwr>;
+		vdd-s12-supply = <&vph_pwr>;
+		vdd-s13-supply = <&vph_pwr>;
+		vdd-l1-l27-supply = <&vreg_s7a_1p025>;
+		vdd-l2-l8-l17-supply = <&vreg_s3a_1p35>;
+		vdd-l3-l11-supply = <&vreg_s7a_1p025>;
+		vdd-l4-l5-supply = <&vreg_s7a_1p025>;
+		vdd-l6-supply = <&vph_pwr>;
+		vdd-l7-l12-l14-l15-supply = <&vreg_s5a_2p04>;
+		vdd-l9-supply = <&vreg_bob>;
+		vdd-l10-l23-l25-supply = <&vreg_bob>;
+		vdd-l13-l19-l21-supply = <&vreg_bob>;
+		vdd-l16-l28-supply = <&vreg_bob>;
+		vdd-l18-l22-supply = <&vreg_bob>;
+		vdd-l20-l24-supply = <&vreg_bob>;
+		vdd-l26-supply = <&vreg_s3a_1p35>;
+		vin-lvs-1-2-supply = <&vreg_s4a_1p8>;
+
+		vreg_s2a_1p125: smps2 {
+			regulator-min-microvolt = <1100000>;
+			regulator-max-microvolt = <1100000>;
+		};
+
+		vreg_s3a_1p35: smps3 {
+			regulator-min-microvolt = <1352000>;
+			regulator-max-microvolt = <1352000>;
+		};
+
+		vreg_s5a_2p04: smps5 {
+			regulator-min-microvolt = <1904000>;
+			regulator-max-microvolt = <2040000>;
+		};
+
+		vreg_s7a_1p025: smps7 {
+			regulator-min-microvolt = <900000>;
+			regulator-max-microvolt = <1028000>;
+		};
+
+		vdd_qusb_hs0:
+		vdda_hp_pcie_core:
+		vdda_mipi_csi0_0p9:
+		vdda_mipi_csi1_0p9:
+		vdda_mipi_csi2_0p9:
+		vdda_mipi_dsi0_pll:
+		vdda_mipi_dsi1_pll:
+		vdda_qlink_lv:
+		vdda_qlink_lv_ck:
+		vdda_qrefs_0p875:
+		vdda_pcie_core:
+		vdda_pll_cc_ebi01:
+		vdda_pll_cc_ebi23:
+		vdda_sp_sensor:
+		vdda_ufs1_core:
+		vdda_ufs2_core:
+		vdda_usb1_ss_core:
+		vdda_usb2_ss_core:
+		vreg_l1a_0p875: ldo1 {
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <880000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vddpx_10:
+		vreg_l2a_1p2: ldo2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-always-on;
+		};
+
+		vreg_l3a_1p0: ldo3 {
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1000000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vdd_wcss_cx:
+		vdd_wcss_mx:
+		vdda_wcss_pll:
+		vreg_l5a_0p8: ldo5 {
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vddpx_13:
+		vreg_l6a_1p8: ldo6 {
+			regulator-min-microvolt = <1856000>;
+			regulator-max-microvolt = <1856000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l7a_1p8: ldo7 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l8a_1p2: ldo8 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1248000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l9a_1p8: ldo9 {
+			regulator-min-microvolt = <1704000>;
+			regulator-max-microvolt = <2928000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l10a_1p8: ldo10 {
+			regulator-min-microvolt = <1704000>;
+			regulator-max-microvolt = <2928000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l11a_1p0: ldo11 {
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1048000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vdd_qfprom:
+		vdd_qfprom_sp:
+		vdda_apc1_cs_1p8:
+		vdda_gfx_cs_1p8:
+		vdda_qrefs_1p8:
+		vdda_qusb_hs0_1p8:
+		vddpx_11:
+		vreg_l12a_1p8: ldo12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vddpx_2:
+		vreg_l13a_2p95: ldo13 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l14a_1p88: ldo14 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l15a_1p8: ldo15 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l16a_2p7: ldo16 {
+			regulator-min-microvolt = <2704000>;
+			regulator-max-microvolt = <2704000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l17a_1p3: ldo17 {
+			regulator-min-microvolt = <1304000>;
+			regulator-max-microvolt = <1304000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l18a_2p7: ldo18 {
+			regulator-min-microvolt = <2704000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l19a_3p0: ldo19 {
+			regulator-min-microvolt = <2856000>;
+			regulator-max-microvolt = <3104000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l20a_2p95: ldo20 {
+			regulator-min-microvolt = <2704000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l21a_2p95: ldo21 {
+			regulator-min-microvolt = <2704000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l22a_2p85: ldo22 {
+			regulator-min-microvolt = <2864000>;
+			regulator-max-microvolt = <3312000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l23a_3p3: ldo23 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3312000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vdda_qusb_hs0_3p1:
+		vreg_l24a_3p075: ldo24 {
+			regulator-min-microvolt = <3088000>;
+			regulator-max-microvolt = <3088000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l25a_3p3: ldo25 {
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3312000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vdda_hp_pcie_1p2:
+		vdda_hv_ebi0:
+		vdda_hv_ebi1:
+		vdda_hv_ebi2:
+		vdda_hv_ebi3:
+		vdda_mipi_csi_1p25:
+		vdda_mipi_dsi0_1p2:
+		vdda_mipi_dsi1_1p2:
+		vdda_pcie_1p2:
+		vdda_ufs1_1p2:
+		vdda_ufs2_1p2:
+		vdda_usb1_ss_1p2:
+		vdda_usb2_ss_1p2:
+		vreg_l26a_1p2: ldo26 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l28a_3p0: ldo28 {
+			regulator-min-microvolt = <2856000>;
+			regulator-max-microvolt = <3008000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_lvs1a_1p8: lvs1 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		vreg_lvs2a_1p8: lvs2 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+	};
+
+	pmi8998-rpmh-regulators {
+		compatible = "qcom,pmi8998-rpmh-regulators";
+		qcom,pmic-id = "b";
+
+		vdd-bob-supply = <&vph_pwr>;
+
+		vreg_bob: bob {
+			regulator-min-microvolt = <3312000>;
+			regulator-max-microvolt = <3600000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>;
+			regulator-allow-bypass;
+		};
+	};
+
+	pm8005-rpmh-regulators {
+		compatible = "qcom,pm8005-rpmh-regulators";
+		qcom,pmic-id = "c";
+
+		vdd-s1-supply = <&vph_pwr>;
+		vdd-s2-supply = <&vph_pwr>;
+		vdd-s3-supply = <&vph_pwr>;
+		vdd-s4-supply = <&vph_pwr>;
+
+		vreg_s3c_0p6: smps3 {
+			regulator-min-microvolt = <600000>;
+			regulator-max-microvolt = <600000>;
+		};
+	};
+};
+
+&cdsp_pas {
+	status = "okay";
+	firmware-name = "qcom/sdm845/axolotl/cdsp.mbn";
+};
+
+&dsi0 {
+	status = "okay";
+	vdda-supply = <&vdda_mipi_dsi0_1p2>;
+
+	panel@0 {
+		compatible = "visionox,rm69299-shift";
+		status = "okay";
+		reg = <0>;
+		vdda-supply = <&vreg_l14a_1p88>;
+		vdd3p3-supply = <&vreg_l28a_3p0>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		reset-gpios = <&tlmm 6 GPIO_ACTIVE_HIGH>;
+
+		pinctrl-names = "default", "sleep";
+		pinctrl-0 = <&sde_dsi_active &sde_te_active>;
+		pinctrl-1 = <&sde_dsi_suspend &sde_te_suspend>;
+
+		port {
+			panel_in_0: endpoint {
+				remote-endpoint = <&dsi0_out>;
+			};
+		};
+	};
+};
+
+&dsi0_out {
+	remote-endpoint = <&panel_in_0>;
+	data-lanes = <0 1 2 3>;
+};
+
+&dsi0_phy {
+	status = "okay";
+	vdds-supply = <&vdda_mipi_dsi0_pll>;
+};
+
+&gcc {
+	protected-clocks = <GCC_QSPI_CORE_CLK>,
+			   <GCC_QSPI_CORE_CLK_SRC>,
+			   <GCC_QSPI_CNOC_PERIPH_AHB_CLK>,
+			   <GCC_LPASS_Q6_AXI_CLK>,
+			   <GCC_LPASS_SWAY_CLK>;
+};
+
+&gmu {
+	status = "okay";
+};
+
+&gpu {
+	status = "okay";
+
+	zap-shader {
+		memory-region = <&gpu_mem>;
+		firmware-name = "qcom/sdm845/axolotl/a630_zap.mbn";
+	};
+};
+
+&i2c5 {
+	status = "okay";
+
+	touchscreen@38 {
+		compatible = "focaltech,fts8719";
+		reg = <0x38>;
+		wakeup-source;
+		interrupt-parent = <&tlmm>;
+		interrupts = <125 0x2>;
+		vdd-supply = <&vreg_l28a_3p0>;
+		vcc-i2c-supply = <&vreg_l14a_1p88>;
+
+		pinctrl-names = "default", "suspend";
+		pinctrl-0 = <&ts_int_active &ts_reset_active>;
+		pinctrl-1 = <&ts_int_suspend &ts_reset_suspend>;
+
+		reset-gpio = <&tlmm 99 GPIO_ACTIVE_HIGH>;
+		irq-gpio = <&tlmm 125 GPIO_TRANSITORY>;
+		touchscreen-size-x = <1080>;
+		touchscreen-size-y = <2160>;
+		focaltech,max-touch-number = <5>;
+	};
+};
+
+&ipa {
+	status = "okay";
+
+	memory-region = <&ipa_fw_mem>;
+	firmware-name = "qcom/sdm845/axolotl/ipa_fws.mbn";
+};
+
+&mdss {
+	status = "okay";
+};
+
+&mss_pil {
+	status = "okay";
+	firmware-name = "qcom/sdm845/axolotl/mba.mbn", "qcom/sdm845/axolotl/modem.mbn";
+};
+
+&pm8998_gpio {
+	volume_up_gpio: pm8998-gpio6-state {
+		pinconf {
+			pins = "gpio6";
+			function = "normal";
+			input-enable;
+			bias-pull-up;
+			qcom,drive-strength = <0>;
+		};
+	};
+};
+
+&pm8998_pon {
+	volume_down_resin: resin {
+		compatible = "qcom,pm8941-resin";
+		interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>;
+		debounce = <15625>;
+		bias-pull-up;
+		linux,code = <KEY_VOLUMEDOWN>;
+	};
+};
+
+&pmi8998_lpg {
+	status = "okay";
+
+	multi-led {
+		color = <LED_COLOR_ID_RGB>;
+		function = LED_FUNCTION_STATUS;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		led@3 {
+			reg = <3>;
+			color = <LED_COLOR_ID_BLUE>;
+		};
+
+		led@4 {
+			reg = <4>;
+			color = <LED_COLOR_ID_GREEN>;
+		};
+
+		led@5 {
+			reg = <5>;
+			color = <LED_COLOR_ID_RED>;
+		};
+	};
+};
+
+&qup_uart9_default {
+	pinconf-rx {
+		pins = "gpio5";
+		drive-strength = <2>;
+		bias-pull-up;
+	};
+
+	pinconf-tx {
+		pins = "gpio4";
+		drive-strength = <2>;
+		bias-disable;
+	};
+};
+
+&qupv3_id_0 {
+	status = "okay";
+};
+
+&qupv3_id_1 {
+	status = "okay";
+};
+
+&tlmm {
+	gpio-reserved-ranges = <0 4>, <81 4>;
+
+	sde_dsi_active: sde-dsi-active {
+		mux {
+			pins = "gpio6", "gpio11";
+			function = "gpio";
+		};
+
+		config {
+			pins = "gpio6", "gpio11";
+			drive-strength = <8>;
+			bias-disable;
+		};
+	};
+
+	sde_dsi_suspend: sde-dsi-suspend {
+		mux {
+			pins = "gpio6", "gpio11";
+			function = "gpio";
+		};
+
+		config {
+			pins = "gpio6", "gpio11";
+			drive-strength = <2>;
+			bias-pull-down;
+		};
+	};
+
+	sde_te_active: sde-te-active {
+		mux {
+			pins = "gpio10";
+			function = "mdp_vsync";
+		};
+
+		config {
+			pins = "gpio10";
+			drive-strength = <2>;
+			bias-pull-down;
+		};
+	};
+
+	sde_te_suspend: sde-te-suspend {
+		mux {
+			pins = "gpio10";
+			function = "mdp_vsync";
+		};
+
+		config {
+			pins = "gpio10";
+			drive-strength = <2>;
+			bias-pull-down;
+		};
+	};
+
+	ts_int_active: ts-int-active {
+		mux {
+			pins = "gpio125";
+			function = "gpio";
+		};
+
+		config {
+			pins = "gpio125";
+			drive-strength = <8>;
+			bias-pull-up;
+			input-enable;
+		};
+	};
+
+	ts_int_suspend: ts-int-suspend {
+		mux {
+			pins = "gpio125";
+			function = "gpio";
+		};
+
+		config {
+			pins = "gpio125";
+			drive-strength = <2>;
+			bias-pull-down;
+			input-enable;
+		};
+	};
+
+	ts_reset_active: ts-reset-active {
+		mux {
+			pins = "gpio99";
+			function = "gpio";
+		};
+
+		config {
+			pins = "gpio99";
+			drive-strength = <8>;
+			bias-pull-up;
+		};
+	};
+
+	ts_reset_suspend: ts-reset-suspend {
+		mux {
+			pins = "gpio99";
+			function = "gpio";
+		};
+
+		config {
+			pins = "gpio99";
+			drive-strength = <2>;
+			bias-pull-down;
+		};
+	};
+};
+
+&uart6 {
+	status = "okay";
+
+	bluetooth {
+		compatible = "qcom,wcn3990-bt";
+
+		vddio-supply = <&vreg_s4a_1p8>;
+		vddxo-supply = <&vreg_l7a_1p8>;
+		vddrf-supply = <&vreg_l17a_1p3>;
+		vddch0-supply = <&vreg_l25a_3p3>;
+		max-speed = <3200000>;
+	};
+};
+
+&uart9 {
+	status = "okay";
+};
+
+&ufs_mem_hc {
+	status = "okay";
+
+	reset-gpios = <&tlmm 150 GPIO_ACTIVE_LOW>;
+
+	vcc-supply = <&vreg_l20a_2p95>;
+	vcc-max-microamp = <600000>;
+};
+
+&ufs_mem_phy {
+	status = "okay";
+
+	vdda-phy-supply = <&vdda_ufs1_core>;
+	vdda-pll-supply = <&vdda_ufs1_1p2>;
+};
+
+&usb_1 {
+	status = "okay";
+};
+
+&usb_1_dwc3 {
+	dr_mode = "peripheral";
+};
+
+&usb_1_hsphy {
+	status = "okay";
+
+	vdd-supply = <&vreg_l1a_0p875>;
+	vdda-phy-dpdm-supply = <&vreg_l24a_3p075>;
+	vdda-pll-supply = <&vreg_l12a_1p8>;
+};
+
+&usb_1_qmpphy {
+	status = "okay";
+
+	vdda-phy-supply = <&vreg_l26a_1p2>;
+	vdda-pll-supply = <&vreg_l1a_0p875>;
+};
+
+&venus {
+	status = "okay";
+	firmware-name = "qcom/sdm845/axolotl/venus.mbn";
+};
+
+&wifi {
+	status = "okay";
+
+	vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>;
+	vdd-1.3-rfa-supply = <&vreg_l17a_1p3>;
+	vdd-1.8-xo-supply = <&vreg_l7a_1p8>;
+	vdd-3.3-ch0-supply = <&vreg_l25a_3p3>;
+	vdd-3.3-ch1-supply = <&vreg_l23a_3p3>;
+
+	qcom,snoc-host-cap-8bit-quirk;
+};
diff --git a/arch/arm64/boot/dts/qcom/sdm845-sony-xperia-tama-akari.dts b/arch/arm64/boot/dts/qcom/sdm845-sony-xperia-tama-akari.dts
new file mode 100644
index 000000000000..34f84f1f1eb4
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sdm845-sony-xperia-tama-akari.dts
@@ -0,0 +1,13 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, Konrad Dybcio <konrad.dybcio@somainline.org>
+ */
+
+/dts-v1/;
+
+#include "sdm845-sony-xperia-tama.dtsi"
+
+/ {
+	model = "Sony Xperia XZ2";
+	compatible = "sony,akari-row", "qcom,sdm845";
+};
diff --git a/arch/arm64/boot/dts/qcom/sdm845-sony-xperia-tama-akatsuki.dts b/arch/arm64/boot/dts/qcom/sdm845-sony-xperia-tama-akatsuki.dts
new file mode 100644
index 000000000000..2f5e12deaada
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sdm845-sony-xperia-tama-akatsuki.dts
@@ -0,0 +1,30 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, Konrad Dybcio <konrad.dybcio@somainline.org>
+ */
+
+/dts-v1/;
+
+#include "sdm845-sony-xperia-tama.dtsi"
+
+/ {
+	model = "Sony Xperia XZ3";
+	compatible = "sony,akatsuki-row", "qcom,sdm845";
+};
+
+/* For the future: WLED + LAB/IBB/OLEDB are not used on Akatsuki */
+&vreg_l14a_1p8 {
+	regulator-min-microvolt = <1840000>;
+	regulator-max-microvolt = <1840000>;
+};
+
+&vreg_l22a_2p8 {
+	/* Note: Round-down from 2700000 to be a multiple of PLDO step-size 8000 */
+	regulator-min-microvolt = <2696000>;
+	regulator-max-microvolt = <2696000>;
+};
+
+&vreg_l28a_2p8 {
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+};
diff --git a/arch/arm64/boot/dts/qcom/sdm845-sony-xperia-tama-apollo.dts b/arch/arm64/boot/dts/qcom/sdm845-sony-xperia-tama-apollo.dts
new file mode 100644
index 000000000000..c9e62c72f60e
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sdm845-sony-xperia-tama-apollo.dts
@@ -0,0 +1,13 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, Konrad Dybcio <konrad.dybcio@somainline.org>
+ */
+
+/dts-v1/;
+
+#include "sdm845-sony-xperia-tama.dtsi"
+
+/ {
+	model = "Sony Xperia XZ2 Compact";
+	compatible = "sony,apollo-row", "qcom,sdm845";
+};
diff --git a/arch/arm64/boot/dts/qcom/sdm845-sony-xperia-tama.dtsi b/arch/arm64/boot/dts/qcom/sdm845-sony-xperia-tama.dtsi
new file mode 100644
index 000000000000..51ee42e3c995
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sdm845-sony-xperia-tama.dtsi
@@ -0,0 +1,438 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, Konrad Dybcio <konrad.dybcio@somainline.org>
+ */
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+#include "sdm845.dtsi"
+#include "pm8005.dtsi"
+#include "pm8998.dtsi"
+#include "pmi8998.dtsi"
+
+/ {
+	qcom,msm-id = <321 0x20001>; /* SDM845 v2.1 */
+	qcom,board-id = <8 0>;
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		/* Neither Camera Focus, nor Camera Shutter seem to work... */
+
+		key-vol-down {
+			label = "volume_down";
+			gpios = <&pm8998_gpio 5 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEDOWN>;
+			debounce-interval = <15>;
+			gpio-key,wakeup;
+		};
+	};
+
+	vph_pwr: vph-pwr-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vph_pwr";
+		regulator-min-microvolt = <3700000>;
+		regulator-max-microvolt = <3700000>;
+	};
+
+	vreg_s4a_1p8: pm8998-smps4 {
+		compatible = "regulator-fixed";
+		regulator-name = "vreg_s4a_1p8";
+
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+
+		regulator-always-on;
+		regulator-boot-on;
+
+		vin-supply = <&vph_pwr>;
+	};
+
+	reserved-memory {
+		/* SONY was cool and didn't diverge from MTP this time, yay! */
+		cont_splash_mem: memory@9d400000 {
+			reg = <0x0 0x9d400000 0x0 0x2400000>;
+			no-map;
+		};
+
+		ramoops@ffc00000 {
+			compatible = "ramoops";
+			reg = <0x0 0xffc00000 0x0 0x100000>;
+			record-size = <0x10000>;
+			console-size = <0x60000>;
+			ftrace-size = <0x10000>;
+			pmsg-size = <0x20000>;
+			ecc-size = <16>;
+			no-map;
+		};
+	};
+};
+
+&apps_rsc {
+	pm8998-rpmh-regulators {
+		compatible = "qcom,pm8998-rpmh-regulators";
+		qcom,pmic-id = "a";
+
+		vdd-s1-supply = <&vph_pwr>;
+		vdd-s2-supply = <&vph_pwr>;
+		vdd-s3-supply = <&vph_pwr>;
+		vdd-s4-supply = <&vph_pwr>;
+		vdd-s5-supply = <&vph_pwr>;
+		vdd-s6-supply = <&vph_pwr>;
+		vdd-s7-supply = <&vph_pwr>;
+		vdd-s8-supply = <&vph_pwr>;
+		vdd-s9-supply = <&vph_pwr>;
+		vdd-s10-supply = <&vph_pwr>;
+		vdd-s11-supply = <&vph_pwr>;
+		vdd-s12-supply = <&vph_pwr>;
+		vdd-s13-supply = <&vph_pwr>;
+		vdd-l1-l27-supply = <&vreg_s7a_0p9>;
+		vdd-l2-l8-l17-supply = <&vreg_s3a_1p3>;
+		vdd-l3-l11-supply = <&vreg_s7a_0p9>;
+		vdd-l4-l5-supply = <&vreg_s7a_0p9>;
+		vdd-l6-supply = <&vph_pwr>;
+		vdd-l7-l12-l14-l15-supply = <&vreg_s5a_1p9>;
+		vdd-l9-supply = <&vreg_s5a_1p9>;
+		vdd-l10-l23-l25-supply = <&src_vreg_bob>;
+		vdd-l13-l19-l21-supply = <&src_vreg_bob>;
+		vdd-l16-l28-supply = <&src_vreg_bob>;
+		vdd-l18-l22-supply = <&src_vreg_bob>;
+		vdd-l20-l24-supply = <&src_vreg_bob>;
+		vdd-l26-supply = <&vreg_s3a_1p3>;
+		vin-lvs-1-2-supply = <&vreg_s4a_1p8>;
+
+		vreg_s2a_1p1: smps2 {
+			regulator-min-microvolt = <1100000>;
+			regulator-max-microvolt = <1100000>;
+		};
+
+		vreg_s3a_1p3: smps3 {
+			regulator-min-microvolt = <1352000>;
+			regulator-max-microvolt = <1352000>;
+		};
+
+		vreg_s5a_1p9: smps5 {
+			regulator-min-microvolt = <1904000>;
+			regulator-max-microvolt = <2040000>;
+		};
+
+		vreg_s7a_0p9: smps7 {
+			regulator-min-microvolt = <900000>;
+			regulator-max-microvolt = <1028000>;
+		};
+
+		vreg_l1a_0p9: ldo1 {
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <880000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2a_1p2: ldo2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-always-on;
+		};
+
+		vreg_l3a_1p0: ldo3 {
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1000000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l5a_0p8: ldo5 {
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l6a_1p8: ldo6 {
+			regulator-min-microvolt = <1856000>;
+			regulator-max-microvolt = <1856000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l7a_1p8: ldo7 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l8a_1p2: ldo8 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1248000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l9a_1p7: ldo9 {
+			regulator-min-microvolt = <1704000>;
+			regulator-max-microvolt = <2928000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l10a_1p7: ldo10 {
+			regulator-min-microvolt = <1704000>;
+			regulator-max-microvolt = <2928000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l11a_1p0: ldo11 {
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1048000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l12a_1p8: ldo12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l13a_1p8: ldo13 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l14a_1p8: ldo14 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l15a_1p8: ldo15 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l16a_2p7: ldo16 {
+			regulator-min-microvolt = <2704000>;
+			regulator-max-microvolt = <2704000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l17a_1p3: ldo17 {
+			regulator-min-microvolt = <1304000>;
+			regulator-max-microvolt = <1304000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l18a_2p7: ldo18 {
+			regulator-min-microvolt = <2704000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l19a_2p7: ldo19 {
+			regulator-min-microvolt = <2700000>;
+			regulator-max-microvolt = <2700000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+
+			/*
+			 * The driver *really* doesn't want this regualtor to exist,
+			 * saying that it could not get the current voltage (-ENOTRECOVERABLE)
+			 * even though it surely is used on these devices (as a voltage
+			 * source for camera autofocus)
+			 */
+			status = "disabled";
+		};
+
+		vreg_l20a_2p7: ldo20 {
+			regulator-min-microvolt = <2704000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l21a_2p7: ldo21 {
+			regulator-min-microvolt = <2704000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l22a_2p8: ldo22 {
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l23a_3p0: ldo23 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3312000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l24a_3p1: ldo24 {
+			regulator-min-microvolt = <3088000>;
+			regulator-max-microvolt = <3088000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l25a_3p0: ldo25 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3312000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l26a_1p2: ldo26 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l28a_2p8: ldo28 {
+			regulator-min-microvolt = <2856000>;
+			regulator-max-microvolt = <3008000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_lvs1a_1p8: lvs1 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_lvs2a_1p8: lvs2 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	pmi8998-rpmh-regulators {
+		compatible = "qcom,pmi8998-rpmh-regulators";
+		qcom,pmic-id = "b";
+
+		src_vreg_bob: bob {
+			regulator-min-microvolt = <3312000>;
+			regulator-max-microvolt = <3600000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	pm8005-rpmh-regulators {
+		compatible = "qcom,pm8005-rpmh-regulators";
+		qcom,pmic-id = "c";
+
+		vdd-s1-supply = <&vph_pwr>;
+		vdd-s2-supply = <&vph_pwr>;
+		vdd-s3-supply = <&vph_pwr>;
+		vdd-s4-supply = <&vph_pwr>;
+
+		vreg_s3c_0p6: smps3 {
+			regulator-min-microvolt = <600000>;
+			regulator-max-microvolt = <600000>;
+		};
+	};
+};
+
+&gcc {
+	protected-clocks = <GCC_QSPI_CORE_CLK>,
+			<GCC_QSPI_CORE_CLK_SRC>,
+			<GCC_QSPI_CNOC_PERIPH_AHB_CLK>,
+			<GCC_LPASS_Q6_AXI_CLK>,
+			<GCC_LPASS_SWAY_CLK>;
+};
+
+&i2c5 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	/* Synaptics touchscreen @ 2c, 3c */
+};
+
+&i2c10 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	/* Qcom SMB1355 @ 8, c */
+	/* NXP PN547 NFC @ 28 */
+	/* Renesas IDTP9221 Qi charger @ 61 */
+};
+
+&i2c14 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	/* SONY ToF sensor @ 52 */
+	/* AMS TCS3490 RGB+IR color sensor @ 72 */
+};
+
+&qupv3_id_0 {
+	status = "okay";
+};
+
+&qupv3_id_1 {
+	status = "okay";
+};
+
+&sdhc_2 {
+	status = "okay";
+
+	vmmc-supply = <&vreg_l21a_2p7>;
+	vqmmc-supply = <&vreg_l13a_1p8>;
+	cd-gpios = <&tlmm 126 GPIO_ACTIVE_HIGH>;
+	pinctrl-0 = <&sdc2_default_state>;
+	pinctrl-names = "default";
+	bus-width = <4>;
+	no-sdio;
+	no-emmc;
+};
+
+&tlmm {
+	gpio-reserved-ranges = <0 4>, <81 4>;
+
+	sdc2_default_state: sdc2-default-state {
+		clk {
+			pins = "sdc2_clk";
+			drive-strength = <16>;
+			bias-disable;
+		};
+
+		cmd {
+			pins = "sdc2_cmd";
+			drive-strength = <10>;
+			bias-pull-up;
+		};
+
+		data {
+			pins = "sdc2_data";
+			drive-strength = <10>;
+			bias-pull-up;
+		};
+	};
+};
+
+&uart6 {
+	status = "okay";
+};
+
+&uart9 {
+	status = "okay";
+};
+
+/* BIG WARNING! DO NOT TOUCH UFS, YOUR DEVICE WILL DIE! */
+&ufs_mem_hc { status = "disabled"; };
+&ufs_mem_phy { status = "disabled"; };
+
+&usb_1 {
+	status = "okay";
+
+	qcom,select-utmi-as-pipe-clk;
+};
+
+&usb_1_dwc3 {
+	dr_mode = "peripheral";
+
+	maximum-speed = "high-speed";
+	phys = <&usb_1_hsphy>;
+	phy-names = "usb2-phy";
+};
+
+&usb_1_hsphy {
+	status = "okay";
+
+	vdd-supply = <&vreg_l1a_0p9>;
+	vdda-pll-supply = <&vreg_l12a_1p8>;
+	vdda-phy-dpdm-supply = <&vreg_l24a_3p1>;
+};
diff --git a/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium.dts b/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium.dts
index 580d4cc1296f..0f470cf1ed1c 100644
--- a/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium.dts
+++ b/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium.dts
@@ -45,7 +45,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&vol_up_pin_a>;
 
-		vol-up {
+		key-vol-up {
 			label = "Volume Up";
 			linux,code = <KEY_VOLUMEUP>;
 			gpios = <&pm8998_gpio 6 GPIO_ACTIVE_LOW>;
@@ -121,7 +121,7 @@
 
 &adsp_pas {
 	status = "okay";
-	firmware-name = "qcom/sdm845/adsp.mdt";
+	firmware-name = "qcom/sdm845/beryllium/adsp.mbn";
 };
 
 &apps_rsc {
@@ -185,6 +185,12 @@
 			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 		};
 
+		vreg_l23a_3p3: ldo23 {
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3312000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
 		vreg_l24a_3p075: ldo24 {
 			regulator-min-microvolt = <3088000>;
 			regulator-max-microvolt = <3088000>;
@@ -208,7 +214,7 @@
 
 &cdsp_pas {
 	status = "okay";
-	firmware-name = "qcom/sdm845/cdsp.mdt";
+	firmware-name = "qcom/sdm845/beryllium/cdsp.mbn";
 };
 
 &dsi0 {
@@ -218,13 +224,14 @@
 	panel@0 {
 		compatible = "tianma,fhd-video";
 		reg = <0>;
-		vddi0-supply = <&vreg_l14a_1p8>;
+		vddio-supply = <&vreg_l14a_1p8>;
 		vddpos-supply = <&lab>;
 		vddneg-supply = <&ibb>;
 
 		#address-cells = <1>;
 		#size-cells = <0>;
 
+		backlight = <&pmi8998_wled>;
 		reset-gpios = <&tlmm 6 GPIO_ACTIVE_LOW>;
 
 		port {
@@ -262,7 +269,7 @@
 
 	zap-shader {
 		memory-region = <&gpu_mem>;
-		firmware-name = "qcom/sdm845/a630_zap.mbn";
+		firmware-name = "qcom/sdm845/beryllium/a630_zap.mbn";
 	};
 };
 
@@ -289,11 +296,17 @@
 
 &mss_pil {
 	status = "okay";
-	firmware-name = "qcom/sdm845/mba.mbn", "qcom/sdm845/modem.mdt";
+	firmware-name = "qcom/sdm845/beryllium/mba.mbn", "qcom/sdm845/beryllium/modem.mbn";
+};
+
+&ipa {
+	status = "okay";
+	memory-region = <&ipa_fw_mem>;
+	firmware-name = "qcom/sdm845/beryllium/ipa_fws.mbn";
 };
 
 &pm8998_gpio {
-	vol_up_pin_a: vol-up-active {
+	vol_up_pin_a: vol-up-active-state {
 		pins = "gpio6";
 		function = "normal";
 		input-enable;
@@ -302,6 +315,17 @@
 	};
 };
 
+&pmi8998_wled {
+	status = "okay";
+	qcom,current-boost-limit = <970>;
+	qcom,ovp-millivolt = <29600>;
+	qcom,current-limit-microamp = <20000>;
+	qcom,num-strings = <2>;
+	qcom,switching-freq = <600>;
+	qcom,external-pfet;
+	qcom,cabc;
+};
+
 &pm8998_pon {
 	resin {
 		compatible = "qcom,pm8941-resin";
@@ -315,7 +339,7 @@
 /* QUAT I2S Uses 1 I2S SD Line for audio on TAS2559/60 amplifiers */
 &q6afedai {
 	qi2s@22 {
-		reg = <22>;
+		reg = <QUATERNARY_MI2S_RX>;
 		qcom,sd-lines = <0>;
 	};
 };
@@ -395,7 +419,7 @@
 		};
 
 		codec {
-			sound-dai =  <&wcd9340 0>;
+			sound-dai = <&wcd9340 0>;
 		};
 	};
 
@@ -514,6 +538,7 @@
 
 &venus {
 	status = "okay";
+	firmware-name = "qcom/sdm845/beryllium/venus.mbn";
 };
 
 &wcd9340{
@@ -521,7 +546,7 @@
 	pinctrl-names = "default";
 	clock-names = "extclk";
 	clocks = <&rpmhcc RPMH_LN_BB_CLK2>;
-	reset-gpios = <&tlmm 64 0>;
+	reset-gpios = <&tlmm 64 GPIO_ACTIVE_HIGH>;
 	vdd-buck-supply = <&vreg_s4a_1p8>;
 	vdd-buck-sido-supply = <&vreg_s4a_1p8>;
 	vdd-tx-supply = <&vreg_s4a_1p8>;
@@ -540,6 +565,7 @@
 	vdd-1.8-xo-supply = <&vreg_l7a_1p8>;
 	vdd-1.3-rfa-supply = <&vreg_l17a_1p3>;
 	vdd-3.3-ch0-supply = <&vreg_l25a_3p3>;
+	vdd-3.3-ch1-supply = <&vreg_l23a_3p3>;
 };
 
 /* PINCTRL - additions to nodes defined in sdm845.dtsi */
diff --git a/arch/arm64/boot/dts/qcom/sdm845-xiaomi-polaris.dts b/arch/arm64/boot/dts/qcom/sdm845-xiaomi-polaris.dts
new file mode 100644
index 000000000000..afc17e4d403f
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sdm845-xiaomi-polaris.dts
@@ -0,0 +1,762 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2020, Xilin Wu <strongtz@yeah.net>
+ * Copyright (c) 2022, Molly Sophia <mollysophia379@gmail.com>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+#include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/sound/qcom,q6afe.h>
+#include <dt-bindings/sound/qcom,q6asm.h>
+#include "sdm845.dtsi"
+#include "pm8998.dtsi"
+#include "pmi8998.dtsi"
+#include "pm8005.dtsi"
+
+/*
+ * Delete following upstream (sdm845.dtsi) reserved
+ * memory mappings which are different in this device.
+ */
+/delete-node/ &rmtfs_mem;
+/delete-node/ &adsp_mem;
+/delete-node/ &wlan_msa_mem;
+/delete-node/ &mpss_region;
+/delete-node/ &venus_mem;
+/delete-node/ &cdsp_mem;
+/delete-node/ &mba_region;
+/delete-node/ &slpi_mem;
+/delete-node/ &spss_mem;
+
+/ {
+	model = "Xiaomi Mi MIX 2S";
+	compatible = "xiaomi,polaris", "qcom,sdm845";
+	chassis-type = "handset";
+
+	/* required for bootloader to select correct board */
+	qcom,msm-id = <0x141 0x20001>;
+	qcom,board-id = <0x2a 0x0>;
+
+	aliases {
+		serial0 = &uart9;
+		serial1 = &uart6;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		autorepeat;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&volume_up_gpio>;
+
+		key-vol-up {
+			label = "Volume Up";
+			linux,code = <KEY_VOLUMEUP>;
+			gpios = <&pm8998_gpio 6 GPIO_ACTIVE_LOW>;
+			debounce-interval = <15>;
+		};
+	};
+
+	reserved-memory {
+		adsp_mem: memory@8c500000 {
+			reg = <0 0x8c500000 0 0x1e00000>;
+			no-map;
+		};
+
+		wlan_msa_mem: memory@8e300000 {
+			reg = <0 0x8e300000 0 0x100000>;
+			no-map;
+		};
+
+		mpss_region: memory@8e400000 {
+			reg = <0 0x8e400000 0 0x7800000>;
+			no-map;
+		};
+
+		venus_mem: memory@95c00000 {
+			reg = <0 0x95c00000 0 0x500000>;
+			no-map;
+		};
+
+		cdsp_mem: memory@96100000 {
+			reg = <0 0x96100000 0 0x800000>;
+			no-map;
+		};
+
+		mba_region: memory@96900000 {
+			reg = <0 0x96900000 0 0x200000>;
+			no-map;
+		};
+
+		slpi_mem: memory@96b00000 {
+			reg = <0 0x96b00000 0 0x1400000>;
+			no-map;
+		};
+
+		spss_mem: memory@97f00000 {
+			reg = <0 0x97f00000 0 0x100000>;
+			no-map;
+		};
+
+		rmtfs_mem: memory@f6301000 {
+			compatible = "qcom,rmtfs-mem";
+			reg = <0 0xf6301000 0 0x200000>;
+			no-map;
+
+			qcom,client-id = <1>;
+			qcom,vmid = <15>;
+		};
+	};
+
+	battery: battery {
+		compatible = "simple-battery";
+
+		charge-full-design-microamp-hours = <3400000>;
+		voltage-min-design-microvolt = <3400000>;
+		voltage-max-design-microvolt = <4400000>;
+	};
+
+	vreg_tp_vddio: vreg-tp-vddio {
+		compatible = "regulator-fixed";
+		regulator-name = "vreg_tp_vddio";
+
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+
+		gpio = <&tlmm 23 GPIO_ACTIVE_HIGH>;
+		regulator-always-on;
+		regulator-boot-on;
+		enable-active-high;
+	};
+
+	vreg_s4a_1p8: vreg-s4a-1p8 {
+		compatible = "regulator-fixed";
+		regulator-name = "vreg_s4a_1p8";
+
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
+	};
+};
+
+&apps_rsc {
+	pm8998-rpmh-regulators {
+		compatible = "qcom,pm8998-rpmh-regulators";
+		qcom,pmic-id = "a";
+
+		vreg_s2a_1p1: smps2 {
+			regulator-min-microvolt = <1100000>;
+			regulator-max-microvolt = <1100000>;
+		};
+
+		vreg_s3a_1p35: smps3 {
+			regulator-min-microvolt = <1352000>;
+			regulator-max-microvolt = <1352000>;
+		};
+
+		vreg_s5a_2p04: smps5 {
+			regulator-min-microvolt = <1904000>;
+			regulator-max-microvolt = <2040000>;
+		};
+
+		vreg_s7a_1p025: smps7 {
+			regulator-min-microvolt = <900000>;
+			regulator-max-microvolt = <1028000>;
+		};
+
+		vdda_mipi_dsi0_pll:
+		vdda_ufs1_core:
+		vreg_l1a_0p875: ldo1 {
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <880000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2a_1p2: ldo2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-always-on;
+		};
+
+		vreg_l3a_1p0: ldo3 {
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1000000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l5a_0p8: ldo5 {
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l6a_1p8: ldo6 {
+			regulator-min-microvolt = <1856000>;
+			regulator-max-microvolt = <1856000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l7a_1p8: ldo7 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l8a_1p2: ldo8 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1248000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l9a_1p8: ldo9 {
+			regulator-min-microvolt = <1704000>;
+			regulator-max-microvolt = <2928000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l10a_2p95: ldo10 {
+			regulator-min-microvolt = <1704000>;
+			regulator-max-microvolt = <2928000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l11a_1p05: ldo11 {
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1048000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l12a_1p8: ldo12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l13a_2p95: ldo13 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l14a_1p8: ldo14 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1880000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-always-on;
+		};
+
+		vreg_l15a_1p8: ldo15 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l16a_2p7: ldo16 {
+			regulator-min-microvolt = <2704000>;
+			regulator-max-microvolt = <2704000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l17a_1p3: ldo17 {
+			regulator-min-microvolt = <1304000>;
+			regulator-max-microvolt = <1304000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-always-on;
+		};
+
+		vreg_l18a_2p9: ldo18 {
+			regulator-min-microvolt = <2704000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l19a_3p1: ldo19 {
+			regulator-min-microvolt = <2856000>;
+			regulator-max-microvolt = <3104000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l20a_2p95: ldo20 {
+			regulator-min-microvolt = <2704000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l21a_2p95: ldo21 {
+			regulator-min-microvolt = <2704000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l22a_3p3: ldo22 {
+			regulator-min-microvolt = <2864000>;
+			regulator-max-microvolt = <3312000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l23a_3p3: ldo23 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3312000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l24a_3p075: ldo24 {
+			regulator-min-microvolt = <3088000>;
+			regulator-max-microvolt = <3088000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l25a_3p3: ldo25 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3312000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-always-on;
+		};
+
+		vdda_mipi_dsi0_1p2:
+		vdda_ufs1_1p2:
+		vreg_l26a_1p2: ldo26 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l28a_3p0: ldo28 {
+			regulator-min-microvolt = <2856000>;
+			regulator-max-microvolt = <3008000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-always-on;
+		};
+
+		vreg_lvs1a_1p8: lvs1 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		vreg_lvs2a_1p8: lvs2 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+	};
+
+	pmi8998-rpmh-regulators {
+		compatible = "qcom,pmi8998-rpmh-regulators";
+		qcom,pmic-id = "b";
+
+		vreg_bob: bob {
+			regulator-min-microvolt = <3312000>;
+			regulator-max-microvolt = <3600000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>;
+			regulator-allow-bypass;
+		};
+	};
+
+	pm8005-rpmh-regulators {
+		compatible = "qcom,pm8005-rpmh-regulators";
+		qcom,pmic-id = "c";
+
+		vreg_smp3c_0p6: smps3 {
+			regulator-min-microvolt = <600000>;
+			regulator-max-microvolt = <600000>;
+			regulator-always-on;
+		};
+	};
+};
+
+&cdsp_pas {
+	firmware-name = "qcom/sdm845/polaris/cdsp.mbn";
+	status = "okay";
+};
+
+&dsi0 {
+	vdda-supply = <&vdda_mipi_dsi0_1p2>;
+	status = "okay";
+
+	display_panel: panel@0 {
+		compatible = "jdi,fhd-nt35596s";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <0>;
+
+		reset-gpios = <&tlmm 6 GPIO_ACTIVE_LOW>;
+		vddio-supply = <&vreg_l14a_1p8>;
+		backlight = <&pmi8998_wled>;
+		vddpos-supply = <&lab>;
+		vddneg-supply = <&ibb>;
+
+		pinctrl-names = "default", "sleep";
+		pinctrl-0 = <&sde_dsi_active>;
+		pinctrl-1 = <&sde_dsi_suspend>;
+
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&dsi0_out>;
+			};
+		};
+	};
+};
+
+&dsi0_out {
+	remote-endpoint = <&panel_in>;
+	data-lanes = <0 1 2 3>;
+};
+
+&dsi0_phy {
+	vdds-supply = <&vdda_mipi_dsi0_pll>;
+	status = "okay";
+};
+
+&gcc {
+	protected-clocks = <GCC_QSPI_CORE_CLK>,
+				<GCC_QSPI_CORE_CLK_SRC>,
+				<GCC_QSPI_CNOC_PERIPH_AHB_CLK>,
+				<GCC_LPASS_Q6_AXI_CLK>,
+				<GCC_LPASS_SWAY_CLK>;
+};
+
+&gmu {
+	status = "okay";
+};
+
+&gpi_dma0 {
+	status = "okay";
+};
+
+&gpi_dma1 {
+	status = "okay";
+};
+
+&gpu {
+	status = "okay";
+
+	zap-shader {
+		memory-region = <&gpu_mem>;
+		firmware-name = "qcom/sdm845/polaris/a630_zap.mbn";
+	};
+};
+
+&ibb {
+	regulator-min-microvolt = <4600000>;
+	regulator-max-microvolt = <6000000>;
+	regulator-over-current-protection;
+	regulator-pull-down;
+	regulator-soft-start;
+	qcom,discharge-resistor-kohms = <300>;
+};
+
+&ipa {
+	memory-region = <&ipa_fw_mem>;
+	firmware-name = "qcom/sdm845/polaris/ipa_fws.mbn";
+	status = "okay";
+};
+
+&i2c14 {
+	clock-frequency = <400000>;
+	dmas = <&gpi_dma1 0 6 QCOM_GPI_I2C>,
+		   <&gpi_dma1 1 6 QCOM_GPI_I2C>;
+	dma-names = "tx", "rx";
+	status = "okay";
+
+	touchscreen@20 {
+		compatible = "syna,rmi4-i2c";
+		reg = <0x20>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		interrupts-extended = <&tlmm 125 0x2008>;
+
+		pinctrl-names = "default", "sleep";
+		pinctrl-0 = <&ts_int_default &ts_reset_default>;
+		pinctrl-1 = <&ts_int_sleep &ts_reset_sleep>;
+
+		vdd-supply = <&vreg_l28a_3p0>;
+		vio-supply = <&vreg_tp_vddio>;
+
+		syna,startup-delay-ms = <0xc8>;
+		syna,reset-delay-ms = <0xc8>;
+
+		rmi4-f01@1 {
+			syna,nosleep-mode = <0x1>;
+			reg = <0x1>;
+		};
+
+		rmi4-f12@12 {
+			syna,rezero-wait-ms = <0xc8>;
+			syna,clip-x-high = <0x438>;
+			syna,clip-y-high = <0x870>;
+			syna,sensor-type = <0x1>;
+			syna,clip-x-low = <0x0>;
+			syna,clip-y-low = <0x0>;
+		};
+	};
+};
+
+&lab {
+	regulator-min-microvolt = <4600000>;
+	regulator-max-microvolt = <6000000>;
+	regulator-soft-start;
+	regulator-pull-down;
+};
+
+&mdss {
+	status = "okay";
+};
+
+&mss_pil {
+	firmware-name = "qcom/sdm845/polaris/mba.mbn", "qcom/sdm845/polaris/modem.mbn";
+	status = "okay";
+};
+
+&pmi8998_wled {
+	qcom,current-limit-microamp = <20000>;
+	qcom,current-boost-limit = <970>;
+	qcom,ovp-millivolt = <19600>;
+	qcom,switching-freq = <600>;
+	qcom,num-strings = <4>;
+	qcom,cabc;
+
+	status = "okay";
+};
+
+&pm8998_gpio {
+	volume_up_gpio: pm8998-gpio6-state {
+		pinconf {
+			qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
+			function = "normal";
+			pins = "gpio6";
+			input-enable;
+			bias-pull-up;
+		};
+	};
+};
+
+&pm8998_pon {
+	resin {
+		interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>;
+		compatible = "qcom,pm8941-resin";
+		linux,code = <KEY_VOLUMEDOWN>;
+		debounce = <15625>;
+		bias-pull-up;
+	};
+};
+
+&q6afedai {
+	qi2s@22 {
+		reg = <22>;
+		qcom,sd-lines = <0>;
+	};
+};
+
+&q6asmdai {
+	dai@0 {
+		reg = <0>;
+	};
+
+	dai@1 {
+		reg = <1>;
+	};
+
+	dai@2 {
+		reg = <2>;
+	};
+};
+
+&qupv3_id_0 {
+	status = "okay";
+};
+
+&qupv3_id_1 {
+	status = "okay";
+};
+
+&qup_i2c14_default {
+	pinconf {
+		pins = "gpio33", "gpio34";
+		drive-strength = <2>;
+		bias-disable;
+	};
+};
+
+&tlmm {
+	gpio-reserved-ranges = <0 4>, <81 4>;
+
+	ts_reset_default: ts-reset-default {
+		pins = "gpio99";
+		function = "gpio";
+		drive-strength = <16>;
+		output-high;
+	};
+
+	ts_int_default: ts-int-default {
+		pins = "gpio125";
+		function = "gpio";
+		bias-pull-down;
+		drive-strength = <16>;
+		input-enable;
+	};
+
+	ts_reset_sleep: ts-reset-sleep {
+		pins = "gpio99";
+		function = "gpio";
+		bias-disable;
+		drive-strength = <2>;
+	};
+
+	ts_int_sleep: ts-int-sleep {
+		pins = "gpio125";
+		function = "gpio";
+		bias-pull-down;
+		drive-strength = <2>;
+		input-enable;
+	};
+
+	sde_dsi_active: sde-dsi-active {
+		pins = "gpio6", "gpio10";
+		function = "gpio";
+		drive-strength = <8>;
+		bias-disable;
+	};
+
+	sde_dsi_suspend: sde-dsi-suspend {
+		pins = "gpio6", "gpio10";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	wcd_intr_default: wcd-intr-default {
+		pins = "goui54";
+		function = "gpio";
+		input-enable;
+		bias-pull-down;
+		drive-strength = <2>;
+	};
+};
+
+&uart6 {
+	status = "okay";
+
+	bluetooth {
+		compatible = "qcom,wcn3990-bt";
+
+		/* This path is relative to the qca/ subdir under lib/firmware. */
+		firmware-name = "polaris/crnv21.bin";
+
+		vddio-supply = <&vreg_s4a_1p8>;
+		vddxo-supply = <&vreg_l7a_1p8>;
+		vddrf-supply = <&vreg_l17a_1p3>;
+		vddch0-supply = <&vreg_l25a_3p3>;
+		max-speed = <3200000>;
+	};
+};
+
+&usb_1 {
+	/* We'll use this as USB 2.0 only */
+	qcom,select-utmi-as-pipe-clk;
+	status = "okay";
+};
+
+&usb_1_dwc3 {
+	dr_mode = "peripheral";
+
+	/* Fastest mode for USB 2 */
+	maximum-speed = "high-speed";
+
+	/* Remove USB3 phy */
+	phys = <&usb_1_hsphy>;
+	phy-names = "usb2-phy";
+};
+
+&usb_1_hsphy {
+	vdda-phy-dpdm-supply = <&vreg_l24a_3p075>;
+	vdda-pll-supply = <&vreg_l12a_1p8>;
+	vdd-supply = <&vreg_l1a_0p875>;
+
+	qcom,preemphasis-width = <QUSB2_V2_PREEMPHASIS_WIDTH_HALF_BIT>;
+	qcom,preemphasis-level = <QUSB2_V2_PREEMPHASIS_5_PERCENT>;
+	qcom,hstx-trim-value = <QUSB2_V2_HSTX_TRIM_21_6_MA>;
+	qcom,imp-res-offset-value = <8>;
+
+	status = "okay";
+};
+
+&usb_1_qmpphy {
+	vdda-pll-supply = <&vreg_l1a_0p875>;
+	vdda-phy-supply = <&vreg_l26a_1p2>;
+	status = "okay";
+};
+
+&ufs_mem_hc {
+	reset-gpios = <&tlmm 150 GPIO_ACTIVE_LOW>;
+	vcc-supply = <&vreg_l20a_2p95>;
+	vcc-max-microamp = <800000>;
+	status = "okay";
+};
+
+&ufs_mem_phy {
+	vdda-phy-supply = <&vdda_ufs1_core>;
+	vdda-pll-supply = <&vdda_ufs1_1p2>;
+	status = "okay";
+};
+
+&venus {
+	firmware-name = "qcom/sdm845/polaris/venus.mbn";
+	status = "okay";
+};
+
+&wcd9340 {
+	pinctrl-0 = <&wcd_intr_default>;
+	pinctrl-names = "default";
+	clock-names = "extclk";
+	clocks = <&rpmhcc RPMH_LN_BB_CLK2>;
+	reset-gpios = <&tlmm 64 GPIO_ACTIVE_HIGH>;
+	vdd-buck-sido-supply = <&vreg_s4a_1p8>;
+	vdd-buck-supply = <&vreg_s4a_1p8>;
+	vdd-tx-supply = <&vreg_s4a_1p8>;
+	vdd-rx-supply = <&vreg_s4a_1p8>;
+	vdd-io-supply = <&vreg_s4a_1p8>;
+
+	qcom,micbias1-microvolt = <2700000>;
+	qcom,micbias2-microvolt = <1800000>;
+	qcom,micbias3-microvolt = <2700000>;
+	qcom,micbias4-microvolt = <2700000>;
+};
+
+&wifi {
+	vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>;
+	vdd-1.8-xo-supply = <&vreg_l7a_1p8>;
+	vdd-1.3-rfa-supply = <&vreg_l17a_1p3>;
+	vdd-3.3-ch0-supply = <&vreg_l25a_3p3>;
+	vdd-3.3-ch1-supply = <&vreg_l23a_3p3>;
+
+	qcom,snoc-host-cap-skip-quirk;
+	status = "okay";
+};
+
+/* PINCTRL - additions to nodes defined in sdm845.dtsi */
+
+&qup_uart6_default {
+	pinmux {
+		 pins = "gpio45", "gpio46", "gpio47", "gpio48";
+		 function = "qup6";
+	};
+
+	cts {
+		pins = "gpio45";
+		bias-disable;
+	};
+
+	rts-tx {
+		pins = "gpio46", "gpio47";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	rx {
+		pins = "gpio48";
+		bias-pull-up;
+	};
+};
diff --git a/arch/arm64/boot/dts/qcom/sdm845.dtsi b/arch/arm64/boot/dts/qcom/sdm845.dtsi
index 526087586ba4..d761da47220d 100644
--- a/arch/arm64/boot/dts/qcom/sdm845.dtsi
+++ b/arch/arm64/boot/dts/qcom/sdm845.dtsi
@@ -12,6 +12,7 @@
 #include <dt-bindings/clock/qcom,lpass-sdm845.h>
 #include <dt-bindings/clock/qcom,rpmh.h>
 #include <dt-bindings/clock/qcom,videocc-sdm845.h>
+#include <dt-bindings/dma/qcom-gpi.h>
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/interconnect/qcom,osm-l3.h>
 #include <dt-bindings/interconnect/qcom,sdm845.h>
@@ -79,22 +80,22 @@
 		#size-cells = <2>;
 		ranges;
 
-		hyp_mem: memory@85700000 {
+		hyp_mem: hyp-mem@85700000 {
 			reg = <0 0x85700000 0 0x600000>;
 			no-map;
 		};
 
-		xbl_mem: memory@85e00000 {
+		xbl_mem: xbl-mem@85e00000 {
 			reg = <0 0x85e00000 0 0x100000>;
 			no-map;
 		};
 
-		aop_mem: memory@85fc0000 {
+		aop_mem: aop-mem@85fc0000 {
 			reg = <0 0x85fc0000 0 0x20000>;
 			no-map;
 		};
 
-		aop_cmd_db_mem: memory@85fe0000 {
+		aop_cmd_db_mem: aop-cmd-db-mem@85fe0000 {
 			compatible = "qcom,cmd-db";
 			reg = <0x0 0x85fe0000 0 0x20000>;
 			no-map;
@@ -107,12 +108,12 @@
 			hwlocks = <&tcsr_mutex 3>;
 		};
 
-		tz_mem: memory@86200000 {
+		tz_mem: tz@86200000 {
 			reg = <0 0x86200000 0 0x2d00000>;
 			no-map;
 		};
 
-		rmtfs_mem: memory@88f00000 {
+		rmtfs_mem: rmtfs@88f00000 {
 			compatible = "qcom,rmtfs-mem";
 			reg = <0 0x88f00000 0 0x200000>;
 			no-map;
@@ -121,73 +122,73 @@
 			qcom,vmid = <15>;
 		};
 
-		qseecom_mem: memory@8ab00000 {
+		qseecom_mem: qseecom@8ab00000 {
 			reg = <0 0x8ab00000 0 0x1400000>;
 			no-map;
 		};
 
-		camera_mem: memory@8bf00000 {
+		camera_mem: camera-mem@8bf00000 {
 			reg = <0 0x8bf00000 0 0x500000>;
 			no-map;
 		};
 
-		ipa_fw_mem: memory@8c400000 {
+		ipa_fw_mem: ipa-fw@8c400000 {
 			reg = <0 0x8c400000 0 0x10000>;
 			no-map;
 		};
 
-		ipa_gsi_mem: memory@8c410000 {
+		ipa_gsi_mem: ipa-gsi@8c410000 {
 			reg = <0 0x8c410000 0 0x5000>;
 			no-map;
 		};
 
-		gpu_mem: memory@8c415000 {
+		gpu_mem: gpu@8c415000 {
 			reg = <0 0x8c415000 0 0x2000>;
 			no-map;
 		};
 
-		adsp_mem: memory@8c500000 {
+		adsp_mem: adsp@8c500000 {
 			reg = <0 0x8c500000 0 0x1a00000>;
 			no-map;
 		};
 
-		wlan_msa_mem: memory@8df00000 {
+		wlan_msa_mem: wlan-msa@8df00000 {
 			reg = <0 0x8df00000 0 0x100000>;
 			no-map;
 		};
 
-		mpss_region: memory@8e000000 {
+		mpss_region: mpss@8e000000 {
 			reg = <0 0x8e000000 0 0x7800000>;
 			no-map;
 		};
 
-		venus_mem: memory@95800000 {
+		venus_mem: venus@95800000 {
 			reg = <0 0x95800000 0 0x500000>;
 			no-map;
 		};
 
-		cdsp_mem: memory@95d00000 {
+		cdsp_mem: cdsp@95d00000 {
 			reg = <0 0x95d00000 0 0x800000>;
 			no-map;
 		};
 
-		mba_region: memory@96500000 {
+		mba_region: mba@96500000 {
 			reg = <0 0x96500000 0 0x200000>;
 			no-map;
 		};
 
-		slpi_mem: memory@96700000 {
+		slpi_mem: slpi@96700000 {
 			reg = <0 0x96700000 0 0x1400000>;
 			no-map;
 		};
 
-		spss_mem: memory@97b00000 {
+		spss_mem: spss@97b00000 {
 			reg = <0 0x97b00000 0 0x100000>;
 			no-map;
 		};
 	};
 
-	cpus {
+	cpus: cpus {
 		#address-cells = <2>;
 		#size-cells = <0>;
 
@@ -196,15 +197,14 @@
 			compatible = "qcom,kryo385";
 			reg = <0x0 0x0>;
 			enable-method = "psci";
-			cpu-idle-states = <&LITTLE_CPU_SLEEP_0
-					   &LITTLE_CPU_SLEEP_1
-					   &CLUSTER_SLEEP_0>;
-			capacity-dmips-mhz = <607>;
-			dynamic-power-coefficient = <100>;
+			capacity-dmips-mhz = <611>;
+			dynamic-power-coefficient = <290>;
 			qcom,freq-domain = <&cpufreq_hw 0>;
 			operating-points-v2 = <&cpu0_opp_table>;
 			interconnects = <&gladiator_noc MASTER_APPSS_PROC 3 &mem_noc SLAVE_EBI1 3>,
 					<&osm_l3 MASTER_OSM_L3_APPS &osm_l3 SLAVE_OSM_L3>;
+			power-domains = <&CPU_PD0>;
+			power-domain-names = "psci";
 			#cooling-cells = <2>;
 			next-level-cache = <&L2_0>;
 			L2_0: l2-cache {
@@ -221,15 +221,14 @@
 			compatible = "qcom,kryo385";
 			reg = <0x0 0x100>;
 			enable-method = "psci";
-			cpu-idle-states = <&LITTLE_CPU_SLEEP_0
-					   &LITTLE_CPU_SLEEP_1
-					   &CLUSTER_SLEEP_0>;
-			capacity-dmips-mhz = <607>;
-			dynamic-power-coefficient = <100>;
+			capacity-dmips-mhz = <611>;
+			dynamic-power-coefficient = <290>;
 			qcom,freq-domain = <&cpufreq_hw 0>;
 			operating-points-v2 = <&cpu0_opp_table>;
 			interconnects = <&gladiator_noc MASTER_APPSS_PROC 3 &mem_noc SLAVE_EBI1 3>,
 					<&osm_l3 MASTER_OSM_L3_APPS &osm_l3 SLAVE_OSM_L3>;
+			power-domains = <&CPU_PD1>;
+			power-domain-names = "psci";
 			#cooling-cells = <2>;
 			next-level-cache = <&L2_100>;
 			L2_100: l2-cache {
@@ -243,15 +242,14 @@
 			compatible = "qcom,kryo385";
 			reg = <0x0 0x200>;
 			enable-method = "psci";
-			cpu-idle-states = <&LITTLE_CPU_SLEEP_0
-					   &LITTLE_CPU_SLEEP_1
-					   &CLUSTER_SLEEP_0>;
-			capacity-dmips-mhz = <607>;
-			dynamic-power-coefficient = <100>;
+			capacity-dmips-mhz = <611>;
+			dynamic-power-coefficient = <290>;
 			qcom,freq-domain = <&cpufreq_hw 0>;
 			operating-points-v2 = <&cpu0_opp_table>;
 			interconnects = <&gladiator_noc MASTER_APPSS_PROC 3 &mem_noc SLAVE_EBI1 3>,
 					<&osm_l3 MASTER_OSM_L3_APPS &osm_l3 SLAVE_OSM_L3>;
+			power-domains = <&CPU_PD2>;
+			power-domain-names = "psci";
 			#cooling-cells = <2>;
 			next-level-cache = <&L2_200>;
 			L2_200: l2-cache {
@@ -265,16 +263,15 @@
 			compatible = "qcom,kryo385";
 			reg = <0x0 0x300>;
 			enable-method = "psci";
-			cpu-idle-states = <&LITTLE_CPU_SLEEP_0
-					   &LITTLE_CPU_SLEEP_1
-					   &CLUSTER_SLEEP_0>;
-			capacity-dmips-mhz = <607>;
-			dynamic-power-coefficient = <100>;
+			capacity-dmips-mhz = <611>;
+			dynamic-power-coefficient = <290>;
 			qcom,freq-domain = <&cpufreq_hw 0>;
 			operating-points-v2 = <&cpu0_opp_table>;
 			interconnects = <&gladiator_noc MASTER_APPSS_PROC 3 &mem_noc SLAVE_EBI1 3>,
 					<&osm_l3 MASTER_OSM_L3_APPS &osm_l3 SLAVE_OSM_L3>;
 			#cooling-cells = <2>;
+			power-domains = <&CPU_PD3>;
+			power-domain-names = "psci";
 			next-level-cache = <&L2_300>;
 			L2_300: l2-cache {
 				compatible = "cache";
@@ -288,14 +285,13 @@
 			reg = <0x0 0x400>;
 			enable-method = "psci";
 			capacity-dmips-mhz = <1024>;
-			cpu-idle-states = <&BIG_CPU_SLEEP_0
-					   &BIG_CPU_SLEEP_1
-					   &CLUSTER_SLEEP_0>;
-			dynamic-power-coefficient = <396>;
+			dynamic-power-coefficient = <442>;
 			qcom,freq-domain = <&cpufreq_hw 1>;
 			operating-points-v2 = <&cpu4_opp_table>;
 			interconnects = <&gladiator_noc MASTER_APPSS_PROC 3 &mem_noc SLAVE_EBI1 3>,
 					<&osm_l3 MASTER_OSM_L3_APPS &osm_l3 SLAVE_OSM_L3>;
+			power-domains = <&CPU_PD4>;
+			power-domain-names = "psci";
 			#cooling-cells = <2>;
 			next-level-cache = <&L2_400>;
 			L2_400: l2-cache {
@@ -310,14 +306,13 @@
 			reg = <0x0 0x500>;
 			enable-method = "psci";
 			capacity-dmips-mhz = <1024>;
-			cpu-idle-states = <&BIG_CPU_SLEEP_0
-					   &BIG_CPU_SLEEP_1
-					   &CLUSTER_SLEEP_0>;
-			dynamic-power-coefficient = <396>;
+			dynamic-power-coefficient = <442>;
 			qcom,freq-domain = <&cpufreq_hw 1>;
 			operating-points-v2 = <&cpu4_opp_table>;
 			interconnects = <&gladiator_noc MASTER_APPSS_PROC 3 &mem_noc SLAVE_EBI1 3>,
 					<&osm_l3 MASTER_OSM_L3_APPS &osm_l3 SLAVE_OSM_L3>;
+			power-domains = <&CPU_PD5>;
+			power-domain-names = "psci";
 			#cooling-cells = <2>;
 			next-level-cache = <&L2_500>;
 			L2_500: l2-cache {
@@ -332,14 +327,13 @@
 			reg = <0x0 0x600>;
 			enable-method = "psci";
 			capacity-dmips-mhz = <1024>;
-			cpu-idle-states = <&BIG_CPU_SLEEP_0
-					   &BIG_CPU_SLEEP_1
-					   &CLUSTER_SLEEP_0>;
-			dynamic-power-coefficient = <396>;
+			dynamic-power-coefficient = <442>;
 			qcom,freq-domain = <&cpufreq_hw 1>;
 			operating-points-v2 = <&cpu4_opp_table>;
 			interconnects = <&gladiator_noc MASTER_APPSS_PROC 3 &mem_noc SLAVE_EBI1 3>,
 					<&osm_l3 MASTER_OSM_L3_APPS &osm_l3 SLAVE_OSM_L3>;
+			power-domains = <&CPU_PD6>;
+			power-domain-names = "psci";
 			#cooling-cells = <2>;
 			next-level-cache = <&L2_600>;
 			L2_600: l2-cache {
@@ -354,14 +348,13 @@
 			reg = <0x0 0x700>;
 			enable-method = "psci";
 			capacity-dmips-mhz = <1024>;
-			cpu-idle-states = <&BIG_CPU_SLEEP_0
-					   &BIG_CPU_SLEEP_1
-					   &CLUSTER_SLEEP_0>;
-			dynamic-power-coefficient = <396>;
+			dynamic-power-coefficient = <442>;
 			qcom,freq-domain = <&cpufreq_hw 1>;
 			operating-points-v2 = <&cpu4_opp_table>;
 			interconnects = <&gladiator_noc MASTER_APPSS_PROC 3 &mem_noc SLAVE_EBI1 3>,
 					<&osm_l3 MASTER_OSM_L3_APPS &osm_l3 SLAVE_OSM_L3>;
+			power-domains = <&CPU_PD7>;
+			power-domain-names = "psci";
 			#cooling-cells = <2>;
 			next-level-cache = <&L2_700>;
 			L2_700: l2-cache {
@@ -406,53 +399,35 @@
 			};
 		};
 
-		idle-states {
+		cpu_idle_states: idle-states {
 			entry-method = "psci";
 
 			LITTLE_CPU_SLEEP_0: cpu-sleep-0-0 {
 				compatible = "arm,idle-state";
-				idle-state-name = "little-power-down";
-				arm,psci-suspend-param = <0x40000003>;
+				idle-state-name = "little-rail-power-collapse";
+				arm,psci-suspend-param = <0x40000004>;
 				entry-latency-us = <350>;
 				exit-latency-us = <461>;
 				min-residency-us = <1890>;
 				local-timer-stop;
 			};
 
-			LITTLE_CPU_SLEEP_1: cpu-sleep-0-1 {
-				compatible = "arm,idle-state";
-				idle-state-name = "little-rail-power-down";
-				arm,psci-suspend-param = <0x40000004>;
-				entry-latency-us = <360>;
-				exit-latency-us = <531>;
-				min-residency-us = <3934>;
-				local-timer-stop;
-			};
-
 			BIG_CPU_SLEEP_0: cpu-sleep-1-0 {
 				compatible = "arm,idle-state";
-				idle-state-name = "big-power-down";
-				arm,psci-suspend-param = <0x40000003>;
+				idle-state-name = "big-rail-power-collapse";
+				arm,psci-suspend-param = <0x40000004>;
 				entry-latency-us = <264>;
 				exit-latency-us = <621>;
 				min-residency-us = <952>;
 				local-timer-stop;
 			};
+		};
 
-			BIG_CPU_SLEEP_1: cpu-sleep-1-1 {
-				compatible = "arm,idle-state";
-				idle-state-name = "big-rail-power-down";
-				arm,psci-suspend-param = <0x40000004>;
-				entry-latency-us = <702>;
-				exit-latency-us = <1061>;
-				min-residency-us = <4488>;
-				local-timer-stop;
-			};
-
+		domain-idle-states {
 			CLUSTER_SLEEP_0: cluster-sleep-0 {
-				compatible = "arm,idle-state";
-				idle-state-name = "cluster-power-down";
-				arm,psci-suspend-param = <0x400000F4>;
+				compatible = "domain-idle-state";
+				idle-state-name = "cluster-power-collapse";
+				arm,psci-suspend-param = <0x4100c244>;
 				entry-latency-us = <3263>;
 				exit-latency-us = <6562>;
 				min-residency-us = <9987>;
@@ -461,7 +436,7 @@
 		};
 	};
 
-	cpu0_opp_table: cpu0_opp_table {
+	cpu0_opp_table: opp-table-cpu0 {
 		compatible = "operating-points-v2";
 		opp-shared;
 
@@ -556,7 +531,7 @@
 		};
 	};
 
-	cpu4_opp_table: cpu4_opp_table {
+	cpu4_opp_table: opp-table-cpu4 {
 		compatible = "operating-points-v2";
 		opp-shared;
 
@@ -787,7 +762,7 @@
 			apr {
 				compatible = "qcom,apr-v2";
 				qcom,glink-channels = "apr_audio_svc";
-				qcom,apr-domain = <APR_DOMAIN_ADSP>;
+				qcom,domain = <APR_DOMAIN_ADSP>;
 				#address-cells = <1>;
 				#size-cells = <0>;
 				qcom,intents = <512 20>;
@@ -838,6 +813,7 @@
 				compatible = "qcom,fastrpc";
 				qcom,glink-channels = "fastrpcglink-apps-dsp";
 				label = "adsp";
+				qcom,non-secure-domain;
 				#address-cells = <1>;
 				#size-cells = <0>;
 
@@ -888,6 +864,7 @@
 				compatible = "qcom,fastrpc";
 				qcom,glink-channels = "fastrpcglink-apps-dsp";
 				label = "cdsp";
+				qcom,non-secure-domain;
 				#address-cells = <1>;
 				#size-cells = <0>;
 
@@ -942,12 +919,6 @@
 		};
 	};
 
-	tcsr_mutex: hwlock {
-		compatible = "qcom,tcsr-mutex";
-		syscon = <&tcsr_mutex_regs 0 0x1000>;
-		#hwlock-cells = <1>;
-	};
-
 	smp2p-cdsp {
 		compatible = "qcom,smp2p";
 		qcom,smem = <94>, <432>;
@@ -1047,9 +1018,62 @@
 		};
 	};
 
-	psci {
+	psci: psci {
 		compatible = "arm,psci-1.0";
 		method = "smc";
+
+		CPU_PD0: power-domain-cpu0 {
+			#power-domain-cells = <0>;
+			power-domains = <&CLUSTER_PD>;
+			domain-idle-states = <&LITTLE_CPU_SLEEP_0>;
+		};
+
+		CPU_PD1: power-domain-cpu1 {
+			#power-domain-cells = <0>;
+			power-domains = <&CLUSTER_PD>;
+			domain-idle-states = <&LITTLE_CPU_SLEEP_0>;
+		};
+
+		CPU_PD2: power-domain-cpu2 {
+			#power-domain-cells = <0>;
+			power-domains = <&CLUSTER_PD>;
+			domain-idle-states = <&LITTLE_CPU_SLEEP_0>;
+		};
+
+		CPU_PD3: power-domain-cpu3 {
+			#power-domain-cells = <0>;
+			power-domains = <&CLUSTER_PD>;
+			domain-idle-states = <&LITTLE_CPU_SLEEP_0>;
+		};
+
+		CPU_PD4: power-domain-cpu4 {
+			#power-domain-cells = <0>;
+			power-domains = <&CLUSTER_PD>;
+			domain-idle-states = <&BIG_CPU_SLEEP_0>;
+		};
+
+		CPU_PD5: power-domain-cpu5 {
+			#power-domain-cells = <0>;
+			power-domains = <&CLUSTER_PD>;
+			domain-idle-states = <&BIG_CPU_SLEEP_0>;
+		};
+
+		CPU_PD6: power-domain-cpu6 {
+			#power-domain-cells = <0>;
+			power-domains = <&CLUSTER_PD>;
+			domain-idle-states = <&BIG_CPU_SLEEP_0>;
+		};
+
+		CPU_PD7: power-domain-cpu7 {
+			#power-domain-cells = <0>;
+			power-domains = <&CLUSTER_PD>;
+			domain-idle-states = <&BIG_CPU_SLEEP_0>;
+		};
+
+		CLUSTER_PD: power-domain-cluster {
+			#power-domain-cells = <0>;
+			domain-idle-states = <&CLUSTER_SLEEP_0>;
+		};
 	};
 
 	soc: soc@0 {
@@ -1078,7 +1102,7 @@
 		};
 
 		qfprom@784000 {
-			compatible = "qcom,qfprom";
+			compatible = "qcom,sdm845-qfprom", "qcom,qfprom";
 			reg = <0 0x00784000 0 0x8ff>;
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -1101,7 +1125,7 @@
 			clock-names = "core";
 		};
 
-		qup_opp_table: qup-opp-table {
+		qup_opp_table: opp-table-qup {
 			compatible = "operating-points-v2";
 
 			opp-50000000 {
@@ -1125,6 +1149,29 @@
 			};
 		};
 
+		gpi_dma0: dma-controller@800000 {
+			#dma-cells = <3>;
+			compatible = "qcom,sdm845-gpi-dma";
+			reg = <0 0x00800000 0 0x60000>;
+			interrupts = <GIC_SPI 244 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 245 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 246 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 247 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 248 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 249 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 250 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 251 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 252 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 253 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 254 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 255 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 256 IRQ_TYPE_LEVEL_HIGH>;
+			dma-channels = <13>;
+			dma-channel-mask = <0xfa>;
+			iommus = <&apps_smmu 0x0016 0x0>;
+			status = "disabled";
+		};
+
 		qupv3_id_0: geniqup@8c0000 {
 			compatible = "qcom,geni-se-qup";
 			reg = <0 0x008c0000 0 0x6000>;
@@ -1155,6 +1202,9 @@
 						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_1 0>,
 						<&aggre1_noc MASTER_QUP_1 0 &mem_noc SLAVE_EBI1 0>;
 				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma0 0 0 QCOM_GPI_I2C>,
+				       <&gpi_dma0 1 0 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 
@@ -1171,6 +1221,9 @@
 				interconnects = <&aggre1_noc MASTER_QUP_1 0 &config_noc SLAVE_BLSP_1 0>,
 						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_1 0>;
 				interconnect-names = "qup-core", "qup-config";
+				dmas = <&gpi_dma0 0 0 QCOM_GPI_SPI>,
+				       <&gpi_dma0 1 0 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 
@@ -1206,6 +1259,9 @@
 						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_1 0>,
 						<&aggre1_noc MASTER_QUP_1 0 &mem_noc SLAVE_EBI1 0>;
 				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma0 0 1 QCOM_GPI_I2C>,
+				       <&gpi_dma0 1 1 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 
@@ -1222,6 +1278,9 @@
 				interconnects = <&aggre1_noc MASTER_QUP_1 0 &config_noc SLAVE_BLSP_1 0>,
 						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_1 0>;
 				interconnect-names = "qup-core", "qup-config";
+				dmas = <&gpi_dma0 0 1 QCOM_GPI_SPI>,
+				       <&gpi_dma0 1 1 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 
@@ -1257,6 +1316,9 @@
 						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_1 0>,
 						<&aggre1_noc MASTER_QUP_1 0 &mem_noc SLAVE_EBI1 0>;
 				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma0 0 2 QCOM_GPI_I2C>,
+				       <&gpi_dma0 1 2 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 
@@ -1273,6 +1335,9 @@
 				interconnects = <&aggre1_noc MASTER_QUP_1 0 &config_noc SLAVE_BLSP_1 0>,
 						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_1 0>;
 				interconnect-names = "qup-core", "qup-config";
+				dmas = <&gpi_dma0 0 2 QCOM_GPI_SPI>,
+				       <&gpi_dma0 1 2 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 
@@ -1308,6 +1373,9 @@
 						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_1 0>,
 						<&aggre1_noc MASTER_QUP_1 0 &mem_noc SLAVE_EBI1 0>;
 				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma0 0 3 QCOM_GPI_I2C>,
+				       <&gpi_dma0 1 3 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 
@@ -1324,6 +1392,9 @@
 				interconnects = <&aggre1_noc MASTER_QUP_1 0 &config_noc SLAVE_BLSP_1 0>,
 						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_1 0>;
 				interconnect-names = "qup-core", "qup-config";
+				dmas = <&gpi_dma0 0 3 QCOM_GPI_SPI>,
+				       <&gpi_dma0 1 3 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 
@@ -1359,6 +1430,9 @@
 						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_1 0>,
 						<&aggre1_noc MASTER_QUP_1 0 &mem_noc SLAVE_EBI1 0>;
 				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma0 0 4 QCOM_GPI_I2C>,
+				       <&gpi_dma0 1 4 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 
@@ -1375,6 +1449,9 @@
 				interconnects = <&aggre1_noc MASTER_QUP_1 0 &config_noc SLAVE_BLSP_1 0>,
 						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_1 0>;
 				interconnect-names = "qup-core", "qup-config";
+				dmas = <&gpi_dma0 0 4 QCOM_GPI_SPI>,
+				       <&gpi_dma0 1 4 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 
@@ -1410,6 +1487,9 @@
 						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_1 0>,
 						<&aggre1_noc MASTER_QUP_1 0 &mem_noc SLAVE_EBI1 0>;
 				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma0 0 5 QCOM_GPI_I2C>,
+				       <&gpi_dma0 1 5 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 
@@ -1426,6 +1506,9 @@
 				interconnects = <&aggre1_noc MASTER_QUP_1 0 &config_noc SLAVE_BLSP_1 0>,
 						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_1 0>;
 				interconnect-names = "qup-core", "qup-config";
+				dmas = <&gpi_dma0 0 5 QCOM_GPI_SPI>,
+				       <&gpi_dma0 1 5 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 
@@ -1461,6 +1544,9 @@
 						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_1 0>,
 						<&aggre1_noc MASTER_QUP_1 0 &mem_noc SLAVE_EBI1 0>;
 				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma0 0 6 QCOM_GPI_I2C>,
+				       <&gpi_dma0 1 6 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 
@@ -1477,6 +1563,9 @@
 				interconnects = <&aggre1_noc MASTER_QUP_1 0 &config_noc SLAVE_BLSP_1 0>,
 						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_1 0>;
 				interconnect-names = "qup-core", "qup-config";
+				dmas = <&gpi_dma0 0 6 QCOM_GPI_SPI>,
+				       <&gpi_dma0 1 6 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 
@@ -1524,6 +1613,9 @@
 				interconnects = <&aggre1_noc MASTER_QUP_1 0 &config_noc SLAVE_BLSP_1 0>,
 						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_1 0>;
 				interconnect-names = "qup-core", "qup-config";
+				dmas = <&gpi_dma0 0 7 QCOM_GPI_SPI>,
+				       <&gpi_dma0 1 7 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 
@@ -1544,6 +1636,29 @@
 			};
 		};
 
+		gpi_dma1: dma-controller@0xa00000 {
+			#dma-cells = <3>;
+			compatible = "qcom,sdm845-gpi-dma";
+			reg = <0 0x00a00000 0 0x60000>;
+			interrupts = <GIC_SPI 279 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 280 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 281 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 282 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 283 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 284 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 293 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 294 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 295 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 296 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 297 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 298 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 299 IRQ_TYPE_LEVEL_HIGH>;
+			dma-channels = <13>;
+			dma-channel-mask = <0xfa>;
+			iommus = <&apps_smmu 0x06d6 0x0>;
+			status = "disabled";
+		};
+
 		qupv3_id_1: geniqup@ac0000 {
 			compatible = "qcom,geni-se-qup";
 			reg = <0 0x00ac0000 0 0x6000>;
@@ -1574,6 +1689,9 @@
 						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_2 0>,
 						<&aggre2_noc MASTER_QUP_2 0 &mem_noc SLAVE_EBI1 0>;
 				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma1 0 0 QCOM_GPI_I2C>,
+				       <&gpi_dma1 1 0 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 
@@ -1590,6 +1708,9 @@
 				interconnects = <&aggre2_noc MASTER_QUP_2 0 &config_noc SLAVE_BLSP_2 0>,
 						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_2 0>;
 				interconnect-names = "qup-core", "qup-config";
+				dmas = <&gpi_dma1 0 0 QCOM_GPI_SPI>,
+				       <&gpi_dma1 1 0 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 
@@ -1625,6 +1746,9 @@
 						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_2 0>,
 						<&aggre2_noc MASTER_QUP_2 0 &mem_noc SLAVE_EBI1 0>;
 				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma1 0 1 QCOM_GPI_I2C>,
+				       <&gpi_dma1 1 1 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 
@@ -1641,6 +1765,9 @@
 				interconnects = <&aggre2_noc MASTER_QUP_2 0 &config_noc SLAVE_BLSP_2 0>,
 						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_2 0>;
 				interconnect-names = "qup-core", "qup-config";
+				dmas = <&gpi_dma1 0 1 QCOM_GPI_SPI>,
+				       <&gpi_dma1 1 1 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 
@@ -1676,6 +1803,9 @@
 						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_2 0>,
 						<&aggre2_noc MASTER_QUP_2 0 &mem_noc SLAVE_EBI1 0>;
 				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma1 0 2 QCOM_GPI_I2C>,
+				       <&gpi_dma1 1 2 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 
@@ -1692,6 +1822,9 @@
 				interconnects = <&aggre2_noc MASTER_QUP_2 0 &config_noc SLAVE_BLSP_2 0>,
 						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_2 0>;
 				interconnect-names = "qup-core", "qup-config";
+				dmas = <&gpi_dma1 0 2 QCOM_GPI_SPI>,
+				       <&gpi_dma1 1 2 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 
@@ -1727,6 +1860,9 @@
 						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_2 0>,
 						<&aggre2_noc MASTER_QUP_2 0 &mem_noc SLAVE_EBI1 0>;
 				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma1 0 3 QCOM_GPI_I2C>,
+				       <&gpi_dma1 1 3 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 
@@ -1743,6 +1879,9 @@
 				interconnects = <&aggre2_noc MASTER_QUP_2 0 &config_noc SLAVE_BLSP_2 0>,
 						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_2 0>;
 				interconnect-names = "qup-core", "qup-config";
+				dmas = <&gpi_dma1 0 3 QCOM_GPI_SPI>,
+				       <&gpi_dma1 1 3 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 
@@ -1778,6 +1917,9 @@
 						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_2 0>,
 						<&aggre2_noc MASTER_QUP_2 0 &mem_noc SLAVE_EBI1 0>;
 				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma1 0 4 QCOM_GPI_I2C>,
+				       <&gpi_dma1 1 4 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 
@@ -1794,6 +1936,9 @@
 				interconnects = <&aggre2_noc MASTER_QUP_2 0 &config_noc SLAVE_BLSP_2 0>,
 						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_2 0>;
 				interconnect-names = "qup-core", "qup-config";
+				dmas = <&gpi_dma1 0 4 QCOM_GPI_SPI>,
+				       <&gpi_dma1 1 4 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 
@@ -1829,6 +1974,9 @@
 						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_2 0>,
 						<&aggre2_noc MASTER_QUP_2 0 &mem_noc SLAVE_EBI1 0>;
 				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma1 0 5 QCOM_GPI_I2C>,
+				       <&gpi_dma1 1 5 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 
@@ -1845,6 +1993,9 @@
 				interconnects = <&aggre2_noc MASTER_QUP_2 0 &config_noc SLAVE_BLSP_2 0>,
 						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_2 0>;
 				interconnect-names = "qup-core", "qup-config";
+				dmas = <&gpi_dma1 0 5 QCOM_GPI_SPI>,
+				       <&gpi_dma1 1 5 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 
@@ -1880,6 +2031,9 @@
 						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_2 0>,
 						<&aggre2_noc MASTER_QUP_2 0 &mem_noc SLAVE_EBI1 0>;
 				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma1 0 6 QCOM_GPI_I2C>,
+				       <&gpi_dma1 1 6 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 
@@ -1896,6 +2050,9 @@
 				interconnects = <&aggre2_noc MASTER_QUP_2 0 &config_noc SLAVE_BLSP_2 0>,
 						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_2 0>;
 				interconnect-names = "qup-core", "qup-config";
+				dmas = <&gpi_dma1 0 6 QCOM_GPI_SPI>,
+				       <&gpi_dma1 1 6 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 
@@ -1932,6 +2089,9 @@
 						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_2 0>,
 						<&aggre2_noc MASTER_QUP_2 0 &mem_noc SLAVE_EBI1 0>;
 				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma1 0 7 QCOM_GPI_I2C>,
+				       <&gpi_dma1 1 7 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
 			};
 
 			spi15: spi@a9c000 {
@@ -1947,6 +2107,9 @@
 				interconnects = <&aggre2_noc MASTER_QUP_2 0 &config_noc SLAVE_BLSP_2 0>,
 						<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_BLSP_2 0>;
 				interconnect-names = "qup-core", "qup-config";
+				dmas = <&gpi_dma1 0 7 QCOM_GPI_SPI>,
+				       <&gpi_dma1 1 7 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
 				status = "disabled";
 			};
 
@@ -1967,15 +2130,89 @@
 			};
 		};
 
-		system-cache-controller@1100000 {
+		llcc: system-cache-controller@1100000 {
 			compatible = "qcom,sdm845-llcc";
-			reg = <0 0x01100000 0 0x200000>, <0 0x01300000 0 0x50000>;
+			reg = <0 0x01100000 0 0x31000>, <0 0x01300000 0 0x50000>;
 			reg-names = "llcc_base", "llcc_broadcast_base";
 			interrupts = <GIC_SPI 582 IRQ_TYPE_LEVEL_HIGH>;
 		};
 
+		pmu@114a000 {
+			compatible = "qcom,sdm845-llcc-bwmon";
+			reg = <0 0x0114a000 0 0x1000>;
+			interrupts = <GIC_SPI 580 IRQ_TYPE_LEVEL_HIGH>;
+			interconnects = <&mem_noc MASTER_LLCC 3 &mem_noc SLAVE_EBI1 3>;
+
+			operating-points-v2 = <&llcc_bwmon_opp_table>;
+
+			llcc_bwmon_opp_table: opp-table {
+				compatible = "operating-points-v2";
+
+				/*
+				 * The interconnect path bandwidth taken from
+				 * cpu4_opp_table bandwidth for gladiator_noc-mem_noc
+				 * interconnect.  This also matches the
+				 * bandwidth table of qcom,llccbw (qcom,bw-tbl,
+				 * bus width: 4 bytes) from msm-4.9 downstream
+				 * kernel.
+				 */
+				opp-0 {
+					opp-peak-kBps = <800000>;
+				};
+				opp-1 {
+					opp-peak-kBps = <1804000>;
+				};
+				opp-2 {
+					opp-peak-kBps = <3072000>;
+				};
+				opp-3 {
+					opp-peak-kBps = <5412000>;
+				};
+				opp-4 {
+					opp-peak-kBps = <7216000>;
+				};
+			};
+		};
+
+		pmu@1436400 {
+			compatible = "qcom,sdm845-bwmon", "qcom,msm8998-bwmon";
+			reg = <0 0x01436400 0 0x600>;
+			interrupts = <GIC_SPI 581 IRQ_TYPE_LEVEL_HIGH>;
+			interconnects = <&gladiator_noc MASTER_APPSS_PROC 3 &mem_noc SLAVE_LLCC 3>;
+
+			operating-points-v2 = <&cpu_bwmon_opp_table>;
+
+			cpu_bwmon_opp_table: opp-table {
+				compatible = "operating-points-v2";
+
+				/*
+				 * The interconnect path bandwidth taken from
+				 * cpu4_opp_table bandwidth for OSM L3
+				 * interconnect.  This also matches the OSM L3
+				 * from bandwidth table of qcom,cpu4-l3lat-mon
+				 * (qcom,core-dev-table, bus width: 16 bytes)
+				 * from msm-4.9 downstream kernel.
+				 */
+				opp-0 {
+					opp-peak-kBps = <4800000>;
+				};
+				opp-1 {
+					opp-peak-kBps = <9216000>;
+				};
+				opp-2 {
+					opp-peak-kBps = <15052800>;
+				};
+				opp-3 {
+					opp-peak-kBps = <20889600>;
+				};
+				opp-4 {
+					opp-peak-kBps = <25497600>;
+				};
+			};
+		};
+
 		pcie0: pci@1c00000 {
-			compatible = "qcom,pcie-sdm845", "snps,dw-pcie";
+			compatible = "qcom,pcie-sdm845";
 			reg = <0 0x01c00000 0 0x2000>,
 			      <0 0x60000000 0 0xf1d>,
 			      <0 0x60000f20 0 0xa8>,
@@ -2080,7 +2317,7 @@
 		};
 
 		pcie1: pci@1c08000 {
-			compatible = "qcom,pcie-sdm845", "snps,dw-pcie";
+			compatible = "qcom,pcie-sdm845";
 			reg = <0 0x01c08000 0 0x2000>,
 			      <0 0x40000000 0 0xf1d>,
 			      <0 0x40000f20 0 0xa8>,
@@ -2382,9 +2619,15 @@
 			status = "disabled";
 		};
 
-		tcsr_mutex_regs: syscon@1f40000 {
-			compatible = "syscon";
-			reg = <0 0x01f40000 0 0x40000>;
+		tcsr_mutex: hwlock@1f40000 {
+			compatible = "qcom,tcsr-mutex";
+			reg = <0 0x01f40000 0 0x20000>;
+			#hwlock-cells = <1>;
+		};
+
+		tcsr_regs_1: syscon@1f60000 {
+			compatible = "qcom,sdm845-tcsr", "syscon";
+			reg = <0 0x01f60000 0 0x20000>;
 		};
 
 		tlmm: pinctrl@3400000 {
@@ -2587,6 +2830,13 @@
 					       "gpio2", "gpio3";
 					function = "qup0";
 				};
+
+				config {
+					pins = "gpio0", "gpio1",
+					       "gpio2", "gpio3";
+					drive-strength = <6>;
+					bias-disable;
+				};
 			};
 
 			qup_spi1_default: qup-spi1-default {
@@ -2994,7 +3244,7 @@
 				 <&pdc_reset PDC_MODEM_SYNC_RESET>;
 			reset-names = "mss_restart", "pdc_reset";
 
-			qcom,halt-regs = <&tcsr_mutex_regs 0x23000 0x25000 0x24000>;
+			qcom,halt-regs = <&tcsr_regs_1 0x3000 0x5000 0x4000>;
 
 			power-domains = <&rpmhpd SDM845_CX>,
 					<&rpmhpd SDM845_MX>,
@@ -3492,7 +3742,7 @@
 			};
 		};
 
-		sdhc_2: sdhci@8804000 {
+		sdhc_2: mmc@8804000 {
 			compatible = "qcom,sdm845-sdhci", "qcom,sdhci-msm-v5";
 			reg = <0 0x08804000 0 0x1000>;
 
@@ -3510,7 +3760,7 @@
 
 			status = "disabled";
 
-			sdhc2_opp_table: sdhc2-opp-table {
+			sdhc2_opp_table: opp-table {
 				compatible = "operating-points-v2";
 
 				opp-9600000 {
@@ -3535,7 +3785,7 @@
 			};
 		};
 
-		qspi_opp_table: qspi-opp-table {
+		qspi_opp_table: opp-table-qspi {
 			compatible = "operating-points-v2";
 
 			opp-19200000 {
@@ -3581,7 +3831,7 @@
 			qcom,apps-ch-pipes = <0x780000>;
 			qcom,ea-pc = <0x270>;
 			status = "okay";
-			dmas =	<&slimbam 3>, <&slimbam 4>,
+			dmas = <&slimbam 3>, <&slimbam 4>,
 				<&slimbam 5>, <&slimbam 6>;
 			dma-names = "rx", "tx", "tx2", "rx2";
 
@@ -3596,13 +3846,13 @@
 
 				wcd9340_ifd: ifd@0{
 					compatible = "slim217,250";
-					reg  = <0 0>;
+					reg = <0 0>;
 				};
 
 				wcd9340: codec@1{
 					compatible = "slim217,250";
-					reg  = <1 0>;
-					slim-ifc-dev  = <&wcd9340_ifd>;
+					reg = <1 0>;
+					slim-ifc-dev = <&wcd9340_ifd>;
 
 					#sound-dai-cells = <1>;
 
@@ -3613,10 +3863,10 @@
 					#clock-cells = <0>;
 					clock-frequency = <9600000>;
 					clock-output-names = "mclk";
-					qcom,micbias1-millivolt = <1800>;
-					qcom,micbias2-millivolt = <1800>;
-					qcom,micbias3-millivolt = <1800>;
-					qcom,micbias4-millivolt = <1800>;
+					qcom,micbias1-microvolt = <1800000>;
+					qcom,micbias2-microvolt = <1800000>;
+					qcom,micbias3-microvolt = <1800000>;
+					qcom,micbias4-microvolt = <1800000>;
 
 					#address-cells = <1>;
 					#size-cells = <1>;
@@ -3633,8 +3883,8 @@
 						reg = <0xc85 0x40>;
 						interrupts-extended = <&wcd9340 20>;
 
-						qcom,dout-ports	= <6>;
-						qcom,din-ports	= <2>;
+						qcom,dout-ports = <6>;
+						qcom,din-ports = <2>;
 						qcom,ports-sinterval-low =/bits/ 8  <0x07 0x1F 0x3F 0x7 0x1F 0x3F 0x0F 0x0F>;
 						qcom,ports-offset1 = /bits/ 8 <0x01 0x02 0x0C 0x6 0x12 0x0D 0x07 0x0A >;
 						qcom,ports-offset2 = /bits/ 8 <0x00 0x00 0x1F 0x00 0x00 0x1F 0x00 0x00>;
@@ -3785,10 +4035,13 @@
 			clocks = <&gcc GCC_CFG_NOC_USB3_PRIM_AXI_CLK>,
 				 <&gcc GCC_USB30_PRIM_MASTER_CLK>,
 				 <&gcc GCC_AGGRE_USB3_PRIM_AXI_CLK>,
-				 <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
-				 <&gcc GCC_USB30_PRIM_SLEEP_CLK>;
-			clock-names = "cfg_noc", "core", "iface", "mock_utmi",
-				      "sleep";
+				 <&gcc GCC_USB30_PRIM_SLEEP_CLK>,
+				 <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>;
+			clock-names = "cfg_noc",
+				      "core",
+				      "iface",
+				      "sleep",
+				      "mock_utmi";
 
 			assigned-clocks = <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
 					  <&gcc GCC_USB30_PRIM_MASTER_CLK>;
@@ -3809,7 +4062,7 @@
 					<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_USB3_0 0>;
 			interconnect-names = "usb-ddr", "apps-usb";
 
-			usb_1_dwc3: dwc3@a600000 {
+			usb_1_dwc3: usb@a600000 {
 				compatible = "snps,dwc3";
 				reg = <0 0x0a600000 0 0xcd00>;
 				interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
@@ -3833,10 +4086,13 @@
 			clocks = <&gcc GCC_CFG_NOC_USB3_SEC_AXI_CLK>,
 				 <&gcc GCC_USB30_SEC_MASTER_CLK>,
 				 <&gcc GCC_AGGRE_USB3_SEC_AXI_CLK>,
-				 <&gcc GCC_USB30_SEC_MOCK_UTMI_CLK>,
-				 <&gcc GCC_USB30_SEC_SLEEP_CLK>;
-			clock-names = "cfg_noc", "core", "iface", "mock_utmi",
-				      "sleep";
+				 <&gcc GCC_USB30_SEC_SLEEP_CLK>,
+				 <&gcc GCC_USB30_SEC_MOCK_UTMI_CLK>;
+			clock-names = "cfg_noc",
+				      "core",
+				      "iface",
+				      "sleep",
+				      "mock_utmi";
 
 			assigned-clocks = <&gcc GCC_USB30_SEC_MOCK_UTMI_CLK>,
 					  <&gcc GCC_USB30_SEC_MASTER_CLK>;
@@ -3857,7 +4113,7 @@
 					<&gladiator_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_USB3_1 0>;
 			interconnect-names = "usb-ddr", "apps-usb";
 
-			usb_2_dwc3: dwc3@a800000 {
+			usb_2_dwc3: usb@a800000 {
 				compatible = "snps,dwc3";
 				reg = <0 0x0a800000 0 0xcd00>;
 				interrupts = <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
@@ -3906,7 +4162,7 @@
 				compatible = "venus-encoder";
 			};
 
-			venus_opp_table: venus-opp-table {
+			venus_opp_table: opp-table {
 				compatible = "operating-points-v2";
 
 				opp-100000000 {
@@ -4139,9 +4395,11 @@
 			#clock-cells = <1>;
 			#reset-cells = <1>;
 			#power-domain-cells = <1>;
+			clocks = <&rpmhcc RPMH_CXO_CLK>;
+			clock-names = "bi_tcxo";
 		};
 
-		dsi_opp_table: dsi-opp-table {
+		dsi_opp_table: opp-table-dsi {
 			compatible = "operating-points-v2";
 
 			opp-19200000 {
@@ -4177,13 +4435,10 @@
 
 			power-domains = <&dispcc MDSS_GDSC>;
 
-			clocks = <&gcc GCC_DISP_AHB_CLK>,
+			clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>,
 				 <&dispcc DISP_CC_MDSS_MDP_CLK>;
 			clock-names = "iface", "core";
 
-			assigned-clocks = <&dispcc DISP_CC_MDSS_MDP_CLK>;
-			assigned-clock-rates = <300000000>;
-
 			interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-controller;
 			#interrupt-cells = <1>;
@@ -4201,7 +4456,7 @@
 			#size-cells = <2>;
 			ranges;
 
-			mdss_mdp: mdp@ae01000 {
+			mdss_mdp: display-controller@ae01000 {
 				compatible = "qcom,sdm845-dpu";
 				reg = <0 0x0ae01000 0 0x8f000>,
 				      <0 0x0aeb0000 0 0x2008>;
@@ -4214,15 +4469,13 @@
 					 <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
 				clock-names = "gcc-bus", "iface", "bus", "core", "vsync";
 
-				assigned-clocks = <&dispcc DISP_CC_MDSS_MDP_CLK>,
-						  <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
-				assigned-clock-rates = <300000000>,
-						       <19200000>;
+				assigned-clocks = <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
+				assigned-clock-rates = <19200000>;
 				operating-points-v2 = <&mdp_opp_table>;
 				power-domains = <&rpmhpd SDM845_CX>;
 
 				interrupt-parent = <&mdss>;
-				interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
+				interrupts = <0>;
 
 				ports {
 					#address-cells = <1>;
@@ -4243,7 +4496,7 @@
 					};
 				};
 
-				mdp_opp_table: mdp-opp-table {
+				mdp_opp_table: opp-table {
 					compatible = "operating-points-v2";
 
 					opp-19200000 {
@@ -4274,7 +4527,7 @@
 				reg-names = "dsi_ctrl";
 
 				interrupt-parent = <&mdss>;
-				interrupts = <4 IRQ_TYPE_LEVEL_HIGH>;
+				interrupts = <4>;
 
 				clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK>,
 					 <&dispcc DISP_CC_MDSS_BYTE0_INTF_CLK>,
@@ -4346,7 +4599,7 @@
 				reg-names = "dsi_ctrl";
 
 				interrupt-parent = <&mdss>;
-				interrupts = <5 IRQ_TYPE_LEVEL_HIGH>;
+				interrupts = <5>;
 
 				clocks = <&dispcc DISP_CC_MDSS_BYTE1_CLK>,
 					 <&dispcc DISP_CC_MDSS_BYTE1_INTF_CLK>,
@@ -4415,7 +4668,6 @@
 
 		gpu: gpu@5000000 {
 			compatible = "qcom,adreno-630.2", "qcom,adreno";
-			#stream-id-cells = <16>;
 
 			reg = <0 0x5000000 0 0x40000>, <0 0x509e000 0 0x10>;
 			reg-names = "kgsl_3d0_reg_memory", "cx_mem";
@@ -4508,7 +4760,7 @@
 		};
 
 		gmu: gmu@506a000 {
-			compatible="qcom,adreno-gmu-630.2", "qcom,adreno-gmu";
+			compatible = "qcom,adreno-gmu-630.2", "qcom,adreno-gmu";
 
 			reg = <0 0x506a000 0 0x30000>,
 			      <0 0xb280000 0 0x10000>,
@@ -4620,8 +4872,8 @@
 		};
 
 		aoss_qmp: power-controller@c300000 {
-			compatible = "qcom,sdm845-aoss-qmp";
-			reg = <0 0x0c300000 0 0x100000>;
+			compatible = "qcom,sdm845-aoss-qmp", "qcom,aoss-qmp";
+			reg = <0 0x0c300000 0 0x400>;
 			interrupts = <GIC_SPI 389 IRQ_TYPE_EDGE_RISING>;
 			mboxes = <&apss_shared 0>;
 
@@ -4636,6 +4888,11 @@
 			};
 		};
 
+		sram@c3f0000 {
+			compatible = "qcom,sdm845-rpmh-stats";
+			reg = <0 0x0c3f0000 0 0x400>;
+		};
+
 		spmi_bus: spmi@c440000 {
 			compatible = "qcom,spmi-pmic-arb";
 			reg = <0 0x0c440000 0 0x1100>,
@@ -4655,8 +4912,8 @@
 			cell-index = <0>;
 		};
 
-		imem@146bf000 {
-			compatible = "simple-mfd";
+		sram@146bf000 {
+			compatible = "qcom,sdm845-imem", "syscon", "simple-mfd";
 			reg = <0 0x146bf000 0 0x1000>;
 
 			#address-cells = <1>;
@@ -4873,7 +5130,7 @@
 			compatible = "qcom,bam-v1.7.0";
 			qcom,controlled-remotely;
 			reg = <0 0x17184000 0 0x2a000>;
-			num-channels  = <31>;
+			num-channels = <31>;
 			interrupts = <GIC_SPI 164 IRQ_TYPE_LEVEL_HIGH>;
 			#dma-cells = <1>;
 			qcom,ee = <1>;
@@ -4882,9 +5139,9 @@
 		};
 
 		timer@17c90000 {
-			#address-cells = <2>;
-			#size-cells = <2>;
-			ranges;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0 0 0x20000000>;
 			compatible = "arm,armv7-timer-mem";
 			reg = <0 0x17c90000 0 0x1000>;
 
@@ -4892,49 +5149,49 @@
 				frame-number = <0>;
 				interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,
 					     <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0 0x17ca0000 0 0x1000>,
-				      <0 0x17cb0000 0 0x1000>;
+				reg = <0x17ca0000 0x1000>,
+				      <0x17cb0000 0x1000>;
 			};
 
 			frame@17cc0000 {
 				frame-number = <1>;
 				interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0 0x17cc0000 0 0x1000>;
+				reg = <0x17cc0000 0x1000>;
 				status = "disabled";
 			};
 
 			frame@17cd0000 {
 				frame-number = <2>;
 				interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0 0x17cd0000 0 0x1000>;
+				reg = <0x17cd0000 0x1000>;
 				status = "disabled";
 			};
 
 			frame@17ce0000 {
 				frame-number = <3>;
 				interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0 0x17ce0000 0 0x1000>;
+				reg = <0x17ce0000 0x1000>;
 				status = "disabled";
 			};
 
 			frame@17cf0000 {
 				frame-number = <4>;
 				interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0 0x17cf0000 0 0x1000>;
+				reg = <0x17cf0000 0x1000>;
 				status = "disabled";
 			};
 
 			frame@17d00000 {
 				frame-number = <5>;
 				interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0 0x17d00000 0 0x1000>;
+				reg = <0x17d00000 0x1000>;
 				status = "disabled";
 			};
 
 			frame@17d10000 {
 				frame-number = <6>;
 				interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0 0x17d10000 0 0x1000>;
+				reg = <0x17d10000 0x1000>;
 				status = "disabled";
 			};
 		};
@@ -5259,7 +5516,7 @@
 			};
 		};
 
-		gpu-thermal-top {
+		gpu-top-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 
@@ -5274,7 +5531,7 @@
 			};
 		};
 
-		gpu-thermal-bottom {
+		gpu-bottom-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 
diff --git a/arch/arm64/boot/dts/qcom/sdm850-lenovo-yoga-c630.dts b/arch/arm64/boot/dts/qcom/sdm850-lenovo-yoga-c630.dts
index d6b2ba4396f6..be59a8ba9c1f 100644
--- a/arch/arm64/boot/dts/qcom/sdm850-lenovo-yoga-c630.dts
+++ b/arch/arm64/boot/dts/qcom/sdm850-lenovo-yoga-c630.dts
@@ -41,7 +41,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&lid_pin_active>, <&mode_pin_active>;
 
-		lid {
+		switch-lid {
 			gpios = <&tlmm 124 GPIO_ACTIVE_HIGH>;
 			linux,input-type = <EV_SW>;
 			linux,code = <SW_LID>;
@@ -49,26 +49,13 @@
 			wakeup-event-action = <EV_ACT_DEASSERTED>;
 		};
 
-		mode {
+		switch-mode {
 			gpios = <&tlmm 95 GPIO_ACTIVE_HIGH>;
 			linux,input-type = <EV_SW>;
 			linux,code = <SW_TABLET_MODE>;
 		};
 	};
 
-	panel {
-		compatible = "boe,nv133fhm-n61";
-		no-hpd;
-
-		ports {
-			port {
-				panel_in_edp: endpoint {
-					remote-endpoint = <&sn65dsi86_out>;
-				};
-			};
-		};
-	};
-
 	/* Reserved memory changes for IPA */
 	reserved-memory {
 		wlan_msa_mem: memory@8c400000 {
@@ -98,6 +85,12 @@
 
 		clock-frequency = <19200000>;
 	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&sn65dsi86 1000000>;
+		enable-gpios = <&tlmm 11 GPIO_ACTIVE_HIGH>;
+	};
 };
 
 &adsp_pas {
@@ -419,6 +412,7 @@
 		clock-names = "refclk";
 
 		no-hpd;
+		#pwm-cells = <1>;
 
 		ports {
 			#address-cells = <1>;
@@ -438,6 +432,19 @@
 				};
 			};
 		};
+
+		aux-bus {
+			panel: panel {
+				compatible = "boe,nv133fhm-n61";
+				backlight = <&backlight>;
+
+				port {
+					panel_in_edp: endpoint {
+						remote-endpoint = <&sn65dsi86_out>;
+					};
+				};
+			};
+		};
 	};
 };
 
@@ -523,6 +530,10 @@
 	dai@1 {
 		reg = <1>;
 	};
+
+	dai@2 {
+		reg = <2>;
+	};
 };
 
 &sound {
@@ -535,6 +546,7 @@
 		"SpkrLeft IN", "SPK1 OUT",
 		"SpkrRight IN", "SPK2 OUT",
 		"MM_DL1",  "MultiMedia1 Playback",
+		"MM_DL3",  "MultiMedia3 Playback",
 		"MultiMedia2 Capture", "MM_UL2";
 
 	mm1-dai-link {
@@ -551,6 +563,13 @@
 		};
 	};
 
+	mm3-dai-link {
+		link-name = "MultiMedia3";
+		cpu {
+			sound-dai = <&q6asmdai  MSM_FRONTEND_DAI_MULTIMEDIA3>;
+		};
+	};
+
 	slim-dai-link {
 		link-name = "SLIM Playback";
 		cpu {
@@ -562,7 +581,7 @@
 		};
 
 		codec {
-			sound-dai =  <&left_spkr>, <&right_spkr>, <&swm 0>, <&wcd9340 0>;
+			sound-dai = <&left_spkr>, <&right_spkr>, <&swm 0>, <&wcd9340 0>;
 		};
 	};
 
@@ -580,6 +599,21 @@
 			sound-dai = <&wcd9340 1>;
 		};
 	};
+
+	slim-wcd-dai-link {
+		link-name = "SLIM WCD Playback";
+		cpu {
+			sound-dai = <&q6afedai SLIMBUS_1_RX>;
+		};
+
+		platform {
+			sound-dai = <&q6routing>;
+		};
+
+		codec {
+			sound-dai = <&wcd9340 2>;
+		};
+	};
 };
 
 &tlmm {
@@ -738,12 +772,15 @@
 	pinctrl-names = "default";
 	clock-names = "extclk";
 	clocks = <&rpmhcc RPMH_LN_BB_CLK2>;
-	reset-gpios = <&tlmm 64 0>;
+	reset-gpios = <&tlmm 64 GPIO_ACTIVE_HIGH>;
 	vdd-buck-supply = <&vreg_s4a_1p8>;
 	vdd-buck-sido-supply = <&vreg_s4a_1p8>;
 	vdd-tx-supply = <&vreg_s4a_1p8>;
 	vdd-rx-supply = <&vreg_s4a_1p8>;
 	vdd-io-supply = <&vreg_s4a_1p8>;
+	qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000 500000 500000 500000 500000>;
+	qcom,mbhc-headset-vthreshold-microvolt = <1700000>;
+	qcom,mbhc-headphone-vthreshold-microvolt = <50000>;
 
 	swm: swm@c85 {
 		left_spkr: wsa8810-left{
@@ -777,3 +814,8 @@
 
 	qcom,snoc-host-cap-8bit-quirk;
 };
+
+&crypto {
+	/* FIXME: qce_start triggers an SError */
+	status = "disable";
+};
diff --git a/arch/arm64/boot/dts/qcom/sdm850-samsung-w737.dts b/arch/arm64/boot/dts/qcom/sdm850-samsung-w737.dts
new file mode 100644
index 000000000000..f954fe5cb61a
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sdm850-samsung-w737.dts
@@ -0,0 +1,748 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Samsung Galaxy Book2
+ *
+ * Copyright (c) 2022, Xilin Wu <strongtz@yeah.net>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+#include <dt-bindings/input/gpio-keys.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+#include <dt-bindings/sound/qcom,q6afe.h>
+#include <dt-bindings/sound/qcom,q6asm.h>
+#include "sdm850.dtsi"
+#include "pm8998.dtsi"
+
+/*
+ * Update following upstream (sdm845.dtsi) reserved
+ * memory mappings for firmware loading to succeed
+ */
+/delete-node/ &qseecom_mem;
+/delete-node/ &wlan_msa_mem;
+/delete-node/ &slpi_mem;
+/delete-node/ &ipa_fw_mem;
+/delete-node/ &ipa_gsi_mem;
+/delete-node/ &gpu_mem;
+/delete-node/ &mpss_region;
+/delete-node/ &adsp_mem;
+/delete-node/ &cdsp_mem;
+/delete-node/ &venus_mem;
+/delete-node/ &mba_region;
+/delete-node/ &spss_mem;
+
+/ {
+	model = "Samsung Galaxy Book2";
+	compatible = "samsung,w737", "qcom,sdm845";
+	chassis-type = "convertible";
+
+	chosen {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		// Firmware initialized the display at 1280p instead of 1440p
+		framebuffer0: framebuffer@80400000 {
+			compatible = "simple-framebuffer";
+			reg = <0 0x80400000 0 (1920 * 1280 * 4)>;
+			width = <1920>;
+			height = <1280>;
+			stride = <(1920 * 4)>;
+			format = "a8r8g8b8";
+		};
+	};
+
+	aliases {
+		hsuart0 = &uart6;
+	};
+
+	/* Reserved memory changes */
+	reserved-memory {
+		/* Bootloader display framebuffer region */
+		cont_splash_mem: memory@80400000 {
+			reg = <0x0 0x80400000 0x0 0x960000>;
+			no-map;
+		};
+
+		qseecom_mem: memory@8b500000 {
+			reg = <0 0x8b500000 0 0xa00000>;
+			no-map;
+		};
+
+		wlan_msa_mem: memory@8c400000 {
+			reg = <0 0x8c400000 0 0x100000>;
+			no-map;
+		};
+
+		slpi_mem: memory@8c500000 {
+			reg = <0 0x8c500000 0 0x1200000>;
+			no-map;
+		};
+
+		ipa_fw_mem: memory@8d700000 {
+			reg = <0 0x8d700000 0 0x100000>;
+			no-map;
+		};
+
+		gpu_mem: memory@8d800000 {
+			reg = <0 0x8d800000 0 0x5000>;
+			no-map;
+		};
+
+		mpss_region: memory@8e000000 {
+			reg = <0 0x8e000000 0 0x8000000>;
+			no-map;
+		};
+
+		adsp_mem: memory@96000000 {
+			reg = <0 0x96000000 0 0x2000000>;
+			no-map;
+		};
+
+		cdsp_mem: memory@98000000 {
+			reg = <0 0x98000000 0 0x800000>;
+			no-map;
+		};
+
+		venus_mem: memory@98800000 {
+			reg = <0 0x98800000 0 0x500000>;
+			no-map;
+		};
+
+		mba_region: memory@98d00000 {
+			reg = <0 0x98d00000 0 0x200000>;
+			no-map;
+		};
+
+		spss_mem: memory@98f00000 {
+			reg = <0 0x98f00000 0 0x100000>;
+			no-map;
+		};
+	};
+};
+
+&adsp_pas {
+	firmware-name = "qcom/samsung/w737/qcadsp850.mbn";
+	status = "okay";
+};
+
+&apps_rsc {
+	pm8998-rpmh-regulators {
+		compatible = "qcom,pm8998-rpmh-regulators";
+		qcom,pmic-id = "a";
+
+		vdd-l2-l8-l17-supply = <&vreg_s3a_1p35>;
+		vdd-l7-l12-l14-l15-supply = <&vreg_s5a_2p04>;
+
+		vreg_s2a_1p125: smps2 {
+		};
+
+		vreg_s3a_1p35: smps3 {
+			regulator-min-microvolt = <1352000>;
+			regulator-max-microvolt = <1352000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s4a_1p8: smps4 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s5a_2p04: smps5 {
+			regulator-min-microvolt = <2040000>;
+			regulator-max-microvolt = <2040000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s7a_1p025: smps7 {
+		};
+
+		vdd_qusb_hs0:
+		vdda_hp_pcie_core:
+		vdda_mipi_csi0_0p9:
+		vdda_mipi_csi1_0p9:
+		vdda_mipi_csi2_0p9:
+		vdda_mipi_dsi0_pll:
+		vdda_mipi_dsi1_pll:
+		vdda_qlink_lv:
+		vdda_qlink_lv_ck:
+		vdda_qrefs_0p875:
+		vdda_pcie_core:
+		vdda_pll_cc_ebi01:
+		vdda_pll_cc_ebi23:
+		vdda_sp_sensor:
+		vdda_ufs1_core:
+		vdda_ufs2_core:
+		vdda_usb1_ss_core:
+		vdda_usb2_ss_core:
+		vreg_l1a_0p875: ldo1 {
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <880000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vddpx_10:
+		vreg_l2a_1p2: ldo2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-always-on;
+		};
+
+		vreg_l3a_1p0: ldo3 {
+		};
+
+		vdd_wcss_cx:
+		vdd_wcss_mx:
+		vdda_wcss_pll:
+		vreg_l5a_0p8: ldo5 {
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vddpx_13:
+		vreg_l6a_1p8: ldo6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l7a_1p8: ldo7 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l8a_1p2: ldo8 {
+		};
+
+		vreg_l9a_1p8: ldo9 {
+		};
+
+		vreg_l10a_1p8: ldo10 {
+		};
+
+		vreg_l11a_1p0: ldo11 {
+		};
+
+		vdd_qfprom:
+		vdd_qfprom_sp:
+		vdda_apc1_cs_1p8:
+		vdda_gfx_cs_1p8:
+		vdda_qrefs_1p8:
+		vdda_qusb_hs0_1p8:
+		vddpx_11:
+		vreg_l12a_1p8: ldo12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vddpx_2:
+		vreg_l13a_2p95: ldo13 {
+		};
+
+		vreg_l14a_1p88: ldo14 {
+			regulator-min-microvolt = <1880000>;
+			regulator-max-microvolt = <1880000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-always-on;
+		};
+
+		vreg_l15a_1p8: ldo15 {
+		};
+
+		vreg_l16a_2p7: ldo16 {
+		};
+
+		vreg_l17a_1p3: ldo17 {
+			regulator-min-microvolt = <1304000>;
+			regulator-max-microvolt = <1304000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l18a_1p8: ldo18 {
+		};
+
+		vreg_l19a_3p0: ldo19 {
+			regulator-min-microvolt = <3100000>;
+			regulator-max-microvolt = <3108000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l20a_2p95: ldo20 {
+			regulator-min-microvolt = <2960000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l21a_2p95: ldo21 {
+		};
+
+		vreg_l22a_2p85: ldo22 {
+		};
+
+		vreg_l23a_3p3: ldo23 {
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3312000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vdda_qusb_hs0_3p1:
+		vreg_l24a_3p075: ldo24 {
+			regulator-min-microvolt = <3075000>;
+			regulator-max-microvolt = <3083000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l25a_3p3: ldo25 {
+			regulator-min-microvolt = <3104000>;
+			regulator-max-microvolt = <3112000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vdda_hp_pcie_1p2:
+		vdda_hv_ebi0:
+		vdda_hv_ebi1:
+		vdda_hv_ebi2:
+		vdda_hv_ebi3:
+		vdda_mipi_csi_1p25:
+		vdda_mipi_dsi0_1p2:
+		vdda_mipi_dsi1_1p2:
+		vdda_pcie_1p2:
+		vdda_ufs1_1p2:
+		vdda_ufs2_1p2:
+		vdda_usb1_ss_1p2:
+		vdda_usb2_ss_1p2:
+		vreg_l26a_1p2: ldo26 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1208000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l28a_3p0: ldo28 {
+		};
+
+		vreg_lvs1a_1p8: lvs1 {
+		};
+
+		vreg_lvs2a_1p8: lvs2 {
+		};
+	};
+};
+
+&cdsp_pas {
+	firmware-name = "qcom/samsung/w737/qccdsp850.mbn";
+	status = "okay";
+};
+
+&gcc {
+	protected-clocks = <GCC_QSPI_CORE_CLK>,
+			   <GCC_QSPI_CORE_CLK_SRC>,
+			   <GCC_QSPI_CNOC_PERIPH_AHB_CLK>,
+			   <GCC_LPASS_Q6_AXI_CLK>,
+			   <GCC_LPASS_SWAY_CLK>;
+};
+
+&i2c10 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	/* SN65DSI86 @ 0x2c */
+	/* The panel requires dual DSI, which is not supported by the bridge driver */
+};
+
+&i2c11 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	/* HID-I2C Touchscreen @ 0x20 */
+};
+
+&i2c15 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	digitizer@9 {
+		compatible = "wacom,w9013", "hid-over-i2c";
+		reg = <0x9>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pen_irq_l>, <&pen_pdct_l>, <&pen_rst_l>;
+
+		post-power-on-delay-ms = <120>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <119 IRQ_TYPE_LEVEL_LOW>;
+
+		hid-descr-addr = <0x1>;
+	};
+};
+
+&ipa {
+	status = "okay";
+	memory-region = <&ipa_fw_mem>;
+	firmware-name = "qcom/samsung/w737/ipa_fws.elf";
+};
+
+/* No idea why it causes an SError when enabled */
+&llcc {
+	status = "disabled";
+};
+
+&mss_pil {
+	status = "okay";
+	firmware-name = "qcom/samsung/w737/qcdsp1v2850.mbn", "qcom/samsung/w737/qcdsp2850.mbn";
+};
+
+&qup_i2c10_default {
+	pinconf {
+		pins = "gpio55", "gpio56";
+		drive-strength = <2>;
+		bias-disable;
+	};
+};
+
+&qup_i2c11_default {
+	pinconf {
+		pins = "gpio31", "gpio32";
+		drive-strength = <2>;
+		bias-disable;
+	};
+};
+
+&qup_i2c12_default {
+	drive-strength = <2>;
+	bias-disable;
+};
+
+&qup_uart6_default {
+	pinmux {
+		 pins = "gpio45", "gpio46", "gpio47", "gpio48";
+		 function = "qup6";
+	};
+
+	cts {
+		pins = "gpio45";
+		bias-pull-down;
+	};
+
+	rts-tx {
+		pins = "gpio46", "gpio47";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	rx {
+		pins = "gpio48";
+		bias-pull-up;
+	};
+};
+
+&qupv3_id_0 {
+	status = "okay";
+};
+
+&qupv3_id_1 {
+	status = "okay";
+};
+
+&q6asmdai {
+	dai@0 {
+		reg = <0>;
+	};
+
+	dai@1 {
+		reg = <1>;
+	};
+
+	dai@2 {
+		reg = <2>;
+	};
+};
+
+&sound {
+	compatible = "qcom,sdm845-sndcard";
+	model = "Samsung-W737";
+
+	audio-routing =
+		"RX_BIAS", "MCLK",
+		"AMIC2", "MIC BIAS2",
+		"SpkrLeft IN", "SPK1 OUT",
+		"SpkrRight IN", "SPK2 OUT",
+		"MM_DL1",  "MultiMedia1 Playback",
+		"MM_DL3",  "MultiMedia3 Playback",
+		"MultiMedia2 Capture", "MM_UL2";
+
+	mm1-dai-link {
+		link-name = "MultiMedia1";
+		cpu {
+			sound-dai = <&q6asmdai  MSM_FRONTEND_DAI_MULTIMEDIA1>;
+		};
+	};
+
+	mm2-dai-link {
+		link-name = "MultiMedia2";
+		cpu {
+			sound-dai = <&q6asmdai  MSM_FRONTEND_DAI_MULTIMEDIA2>;
+		};
+	};
+
+	mm3-dai-link {
+		link-name = "MultiMedia3";
+		cpu {
+			sound-dai = <&q6asmdai  MSM_FRONTEND_DAI_MULTIMEDIA3>;
+		};
+	};
+
+	slim-dai-link {
+		link-name = "SLIM Playback";
+		cpu {
+			sound-dai = <&q6afedai SLIMBUS_0_RX>;
+		};
+
+		platform {
+			sound-dai = <&q6routing>;
+		};
+
+		codec {
+			sound-dai = <&left_spkr>, <&right_spkr>, <&swm 0>, <&wcd9340 0>;
+		};
+	};
+
+	slimcap-dai-link {
+		link-name = "SLIM Capture";
+		cpu {
+			sound-dai = <&q6afedai SLIMBUS_0_TX>;
+		};
+
+		platform {
+			sound-dai = <&q6routing>;
+		};
+
+		codec {
+			sound-dai = <&wcd9340 1>;
+		};
+	};
+
+	slim-wcd-dai-link {
+		link-name = "SLIM WCD Playback";
+		cpu {
+			sound-dai = <&q6afedai SLIMBUS_1_RX>;
+		};
+
+		platform {
+			sound-dai = <&q6routing>;
+		};
+
+		codec {
+			sound-dai = <&wcd9340 2>;
+		};
+	};
+};
+
+&tlmm {
+	gpio-reserved-ranges = <0 6>, <85 4>;
+
+	pen_irq_l: pen-irq-l {
+		pinmux {
+			pins = "gpio119";
+			function = "gpio";
+		};
+
+		pinconf {
+			pins = "gpio119";
+			bias-disable;
+		};
+	};
+
+	pen_pdct_l: pen-pdct-l {
+		pinmux {
+			pins = "gpio124";
+			function = "gpio";
+		};
+
+		pinconf {
+			pins = "gpio124";
+			bias-disable;
+			drive-strength = <2>;
+			output-high;
+		};
+	};
+
+	pen_rst_l: pen-rst-l {
+		pinmux  {
+			pins = "gpio21";
+			function = "gpio";
+		};
+
+		pinconf {
+			pins = "gpio21";
+			bias-disable;
+			drive-strength = <2>;
+
+			/*
+			 * The pen driver doesn't currently support
+			 * driving this reset line.  By specifying
+			 * output-high here we're relying on the fact
+			 * that this pin has a default pulldown at boot
+			 * (which makes sure the pen was in reset if it
+			 * was powered) and then we set it high here to
+			 * take it out of reset.  Better would be if the
+			 * pen driver could control this and we could
+			 * remove "output-high" here.
+			 */
+			output-high;
+		};
+	};
+
+	wcd_intr_default: wcd_intr_default {
+		pins = "gpio54";
+		function = "gpio";
+
+		input-enable;
+		bias-pull-down;
+		drive-strength = <2>;
+	};
+};
+
+&uart6 {
+	status = "okay";
+
+	bluetooth {
+		compatible = "qcom,wcn3990-bt";
+
+		vddio-supply = <&vreg_s4a_1p8>;
+		vddxo-supply = <&vreg_l7a_1p8>;
+		vddrf-supply = <&vreg_l17a_1p3>;
+		vddch0-supply = <&vreg_l25a_3p3>;
+		vddch1-supply = <&vreg_l23a_3p3>;
+		max-speed = <3200000>;
+	};
+};
+
+&ufs_mem_hc {
+	status = "okay";
+
+	reset-gpios = <&tlmm 150 GPIO_ACTIVE_LOW>;
+
+	vcc-supply = <&vreg_l20a_2p95>;
+	vcc-max-microamp = <600000>;
+};
+
+&ufs_mem_phy {
+	status = "okay";
+
+	vdda-phy-supply = <&vdda_ufs1_core>;
+	vdda-pll-supply = <&vdda_ufs1_1p2>;
+};
+
+&usb_1 {
+	status = "okay";
+};
+
+&usb_1_dwc3 {
+	dr_mode = "host";
+};
+
+&usb_1_hsphy {
+	status = "okay";
+
+	vdd-supply = <&vdda_usb1_ss_core>;
+	vdda-pll-supply = <&vdda_qusb_hs0_1p8>;
+	vdda-phy-dpdm-supply = <&vdda_qusb_hs0_3p1>;
+
+	qcom,imp-res-offset-value = <8>;
+	qcom,hstx-trim-value = <QUSB2_V2_HSTX_TRIM_21_6_MA>;
+	qcom,preemphasis-level = <QUSB2_V2_PREEMPHASIS_5_PERCENT>;
+	qcom,preemphasis-width = <QUSB2_V2_PREEMPHASIS_WIDTH_HALF_BIT>;
+};
+
+&usb_1_qmpphy {
+	status = "okay";
+
+	vdda-phy-supply = <&vdda_usb1_ss_1p2>;
+	vdda-pll-supply = <&vdda_usb1_ss_core>;
+};
+
+&usb_2 {
+	status = "okay";
+};
+
+&usb_2_dwc3 {
+	dr_mode = "host";
+};
+
+&usb_2_hsphy {
+	status = "okay";
+
+	vdd-supply = <&vdda_usb2_ss_core>;
+	vdda-pll-supply = <&vdda_qusb_hs0_1p8>;
+	vdda-phy-dpdm-supply = <&vdda_qusb_hs0_3p1>;
+
+	qcom,imp-res-offset-value = <8>;
+	qcom,hstx-trim-value = <QUSB2_V2_HSTX_TRIM_22_8_MA>;
+};
+
+&usb_2_qmpphy {
+	status = "okay";
+
+	vdda-phy-supply = <&vdda_usb2_ss_1p2>;
+	vdda-pll-supply = <&vdda_usb2_ss_core>;
+};
+
+&venus {
+	status = "okay";
+	firmware-name = "qcom/samsung/w737/qcvss850.mbn";
+};
+
+&wcd9340{
+	pinctrl-0 = <&wcd_intr_default>;
+	pinctrl-names = "default";
+	clock-names = "extclk";
+	clocks = <&rpmhcc RPMH_LN_BB_CLK2>;
+	reset-gpios = <&tlmm 64 GPIO_ACTIVE_HIGH>;
+	vdd-buck-supply = <&vreg_s4a_1p8>;
+	vdd-buck-sido-supply = <&vreg_s4a_1p8>;
+	vdd-tx-supply = <&vreg_s4a_1p8>;
+	vdd-rx-supply = <&vreg_s4a_1p8>;
+	vdd-io-supply = <&vreg_s4a_1p8>;
+	qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000 500000 500000 500000 500000>;
+	qcom,mbhc-headset-vthreshold-microvolt = <1700000>;
+	qcom,mbhc-headphone-vthreshold-microvolt = <50000>;
+
+	swm: swm@c85 {
+		left_spkr: wsa8810-left{
+			compatible = "sdw10217211000";
+			reg = <0 3>;
+			powerdown-gpios = <&wcdgpio 1 GPIO_ACTIVE_HIGH>;
+			#thermal-sensor-cells = <0>;
+			sound-name-prefix = "SpkrLeft";
+			#sound-dai-cells = <0>;
+		};
+
+		right_spkr: wsa8810-right{
+			compatible = "sdw10217211000";
+			powerdown-gpios = <&wcdgpio 2 GPIO_ACTIVE_HIGH>;
+			reg = <0 4>;
+			#thermal-sensor-cells = <0>;
+			sound-name-prefix = "SpkrRight";
+			#sound-dai-cells = <0>;
+		};
+	};
+};
+
+&wifi {
+	status = "okay";
+
+	vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>;
+	vdd-1.8-xo-supply = <&vreg_l7a_1p8>;
+	vdd-1.3-rfa-supply = <&vreg_l17a_1p3>;
+	vdd-3.3-ch0-supply = <&vreg_l25a_3p3>;
+	vdd-3.3-ch1-supply = <&vreg_l23a_3p3>;
+
+	qcom,snoc-host-cap-8bit-quirk;
+};
diff --git a/arch/arm64/boot/dts/qcom/sdm850.dtsi b/arch/arm64/boot/dts/qcom/sdm850.dtsi
index b1c2cf566c7a..da9f6fbe32f6 100644
--- a/arch/arm64/boot/dts/qcom/sdm850.dtsi
+++ b/arch/arm64/boot/dts/qcom/sdm850.dtsi
@@ -16,6 +16,5 @@
 	cpu4_opp34: opp-2956800000 {
 		opp-hz = /bits/ 64 <2956800000>;
 		opp-peak-kBps = <7216000 25497600>;
-		turbo-mode;
 	};
 };
diff --git a/arch/arm64/boot/dts/qcom/sm6125-sony-xperia-seine-pdx201.dts b/arch/arm64/boot/dts/qcom/sm6125-sony-xperia-seine-pdx201.dts
index 45eab0235d66..6a8b88cc4385 100644
--- a/arch/arm64/boot/dts/qcom/sm6125-sony-xperia-seine-pdx201.dts
+++ b/arch/arm64/boot/dts/qcom/sm6125-sony-xperia-seine-pdx201.dts
@@ -42,12 +42,9 @@
 	gpio-keys {
 		status = "okay";
 		compatible = "gpio-keys";
-		input-name = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		autorepeat;
 
-		vol-dn {
+		key-vol-dn {
 			label = "Volume Down";
 			gpios = <&tlmm 47 GPIO_ACTIVE_LOW>;
 			linux,input-type = <1>;
@@ -89,11 +86,19 @@
 	status = "okay";
 };
 
-&sdc2_state_off {
-	sd-cd {
+&sdc2_off_state {
+	sd-cd-pins {
 		pins = "gpio98";
+		drive-strength = <2>;
 		bias-disable;
+	};
+};
+
+&sdc2_on_state {
+	sd-cd-pins {
+		pins = "gpio98";
 		drive-strength = <2>;
+		bias-pull-up;
 	};
 };
 
@@ -103,32 +108,6 @@
 
 &tlmm {
 	gpio-reserved-ranges = <22 2>, <28 6>;
-
-	sdc2_state_on: sdc2-on {
-		clk {
-			pins = "sdc2_clk";
-			bias-disable;
-			drive-strength = <16>;
-		};
-
-		cmd {
-			pins = "sdc2_cmd";
-			bias-pull-up;
-			drive-strength = <10>;
-		};
-
-		data {
-			pins = "sdc2_data";
-			bias-pull-up;
-			drive-strength = <10>;
-		};
-
-		sd-cd {
-			pins = "gpio98";
-			bias-pull-up;
-			drive-strength = <2>;
-		};
-	};
 };
 
 &usb3 {
diff --git a/arch/arm64/boot/dts/qcom/sm6125.dtsi b/arch/arm64/boot/dts/qcom/sm6125.dtsi
index 51286ddbdb10..1fe3fa3ad877 100644
--- a/arch/arm64/boot/dts/qcom/sm6125.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm6125.dtsi
@@ -302,6 +302,56 @@
 				compatible = "qcom,rpmcc-sm6125", "qcom,rpmcc";
 				#clock-cells = <1>;
 			};
+
+			rpmpd: power-controller {
+				compatible = "qcom,sm6125-rpmpd";
+				#power-domain-cells = <1>;
+				operating-points-v2 = <&rpmpd_opp_table>;
+
+				rpmpd_opp_table: opp-table {
+					compatible = "operating-points-v2";
+
+					rpmpd_opp_ret: opp1 {
+						opp-level = <RPM_SMD_LEVEL_RETENTION>;
+					};
+
+					rpmpd_opp_ret_plus: opp2 {
+						opp-level = <RPM_SMD_LEVEL_RETENTION_PLUS>;
+					};
+
+					rpmpd_opp_min_svs: opp3 {
+						opp-level = <RPM_SMD_LEVEL_MIN_SVS>;
+					};
+
+					rpmpd_opp_low_svs: opp4 {
+						opp-level = <RPM_SMD_LEVEL_LOW_SVS>;
+					};
+
+					rpmpd_opp_svs: opp5 {
+						opp-level = <RPM_SMD_LEVEL_SVS>;
+					};
+
+					rpmpd_opp_svs_plus: opp6 {
+						opp-level = <RPM_SMD_LEVEL_SVS_PLUS>;
+					};
+
+					rpmpd_opp_nom: opp7 {
+						opp-level = <RPM_SMD_LEVEL_NOM>;
+					};
+
+					rpmpd_opp_nom_plus: opp8 {
+						opp-level = <RPM_SMD_LEVEL_NOM_PLUS>;
+					};
+
+					rpmpd_opp_turbo: opp9 {
+						opp-level = <RPM_SMD_LEVEL_TURBO>;
+					};
+
+					rpmpd_opp_turbo_no_cpr: opp10 {
+						opp-level = <RPM_SMD_LEVEL_TURBO_NO_CPR>;
+					};
+				};
+			};
 		};
 	};
 
@@ -336,23 +386,43 @@
 			interrupt-controller;
 			#interrupt-cells = <2>;
 
-			sdc2_state_off: sdc2-off {
-				clk {
+			sdc2_off_state: sdc2-off-state {
+				clk-pins {
 					pins = "sdc2_clk";
-					bias-disable;
 					drive-strength = <2>;
+					bias-disable;
 				};
 
-				cmd {
+				cmd-pins {
 					pins = "sdc2_cmd";
+					drive-strength = <2>;
 					bias-pull-up;
+				};
+
+				data-pins {
+					pins = "sdc2_data";
 					drive-strength = <2>;
+					bias-pull-up;
+				};
+			};
+
+			sdc2_on_state: sdc2-on-state {
+				clk {
+					pins = "sdc2_clk";
+					drive-strength = <16>;
+					bias-disable;
 				};
 
-				data {
+				cmd-pins-pins {
+					pins = "sdc2_cmd";
+					drive-strength = <10>;
+					bias-pull-up;
+				};
+
+				data-pins {
 					pins = "sdc2_data";
+					drive-strength = <10>;
 					bias-pull-up;
-					drive-strength = <2>;
 				};
 			};
 		};
@@ -385,7 +455,7 @@
 			reg = <0x045f0000 0x7000>;
 		};
 
-		sdhc_1: sdhci@4744000 {
+		sdhc_1: mmc@4744000 {
 			compatible = "qcom,sm6125-sdhci", "qcom,sdhci-msm-v5";
 			reg = <0x04744000 0x1000>, <0x04745000 0x1000>;
 			reg-names = "hc", "core";
@@ -398,12 +468,18 @@
 				 <&gcc GCC_SDCC1_APPS_CLK>,
 				 <&xo_board>;
 			clock-names = "iface", "core", "xo";
+
+			power-domains = <&rpmpd SM6125_VDDCX>;
+
+			qcom,dll-config = <0x000f642c>;
+			qcom,ddr-config = <0x80040873>;
+
 			bus-width = <8>;
 			non-removable;
 			status = "disabled";
 		};
 
-		sdhc_2: sdhci@4784000 {
+		sdhc_2: mmc@4784000 {
 			compatible = "qcom,sm6125-sdhci", "qcom,sdhci-msm-v5";
 			reg = <0x04784000 0x1000>;
 			reg-names = "hc";
@@ -417,27 +493,38 @@
 				 <&xo_board>;
 			clock-names = "iface", "core", "xo";
 
-			pinctrl-0 = <&sdc2_state_on>;
-			pinctrl-1 = <&sdc2_state_off>;
+			pinctrl-0 = <&sdc2_on_state>;
+			pinctrl-1 = <&sdc2_off_state>;
 			pinctrl-names = "default", "sleep";
 
+			power-domains = <&rpmpd SM6125_VDDCX>;
+
+			qcom,dll-config = <0x0007642c>;
+			qcom,ddr-config = <0x80040873>;
+
 			bus-width = <4>;
 			status = "disabled";
 		};
 
 		usb3: usb@4ef8800 {
-			compatible = "qcom,msm8996-dwc3", "qcom,dwc3";
+			compatible = "qcom,sm6125-dwc3", "qcom,dwc3";
 			reg = <0x04ef8800 0x400>;
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges;
 
-			clocks = <&gcc GCC_USB30_PRIM_MASTER_CLK>,
+			clocks = <&gcc GCC_CFG_NOC_USB3_PRIM_AXI_CLK>,
+				 <&gcc GCC_USB30_PRIM_MASTER_CLK>,
 				 <&gcc GCC_SYS_NOC_USB3_PRIM_AXI_CLK>,
-				 <&gcc GCC_CFG_NOC_USB3_PRIM_AXI_CLK>,
-				 <&gcc GCC_USB3_PRIM_CLKREF_CLK>,
 				 <&gcc GCC_USB30_PRIM_SLEEP_CLK>,
-				 <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>;
+				 <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
+				 <&gcc GCC_USB3_PRIM_CLKREF_CLK>;
+			clock-names = "cfg_noc",
+				      "core",
+				      "iface",
+				      "sleep",
+				      "mock_utmi",
+				      "xo";
 
 			assigned-clocks = <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
 					  <&gcc GCC_USB30_PRIM_MASTER_CLK>;
diff --git a/arch/arm64/boot/dts/qcom/sm6350.dtsi b/arch/arm64/boot/dts/qcom/sm6350.dtsi
index 973e18fe3b67..c39de7d3ace0 100644
--- a/arch/arm64/boot/dts/qcom/sm6350.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm6350.dtsi
@@ -1,11 +1,14 @@
 // SPDX-License-Identifier: BSD-3-Clause
 /*
  * Copyright (c) 2021, Konrad Dybcio <konrad.dybcio@somainline.org>
+ * Copyright (c) 2022, Luca Weiss <luca.weiss@fairphone.com>
  */
 
 #include <dt-bindings/clock/qcom,gcc-sm6350.h>
 #include <dt-bindings/clock/qcom,rpmh.h>
+#include <dt-bindings/dma/qcom-gpi.h>
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interconnect/qcom,sm6350.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/mailbox/qcom-ipcc.h>
 #include <dt-bindings/power/qcom-rpmpd.h>
@@ -361,6 +364,80 @@
 		hwlocks = <&tcsr_mutex 3>;
 	};
 
+	smp2p-adsp {
+		compatible = "qcom,smp2p";
+		qcom,smem = <443>, <429>;
+		interrupts-extended = <&ipcc IPCC_CLIENT_LPASS
+					     IPCC_MPROC_SIGNAL_SMP2P
+					     IRQ_TYPE_EDGE_RISING>;
+		mboxes = <&ipcc IPCC_CLIENT_LPASS
+				IPCC_MPROC_SIGNAL_SMP2P>;
+
+		qcom,local-pid = <0>;
+		qcom,remote-pid = <2>;
+
+		smp2p_adsp_out: master-kernel {
+			qcom,entry-name = "master-kernel";
+			#qcom,smem-state-cells = <1>;
+		};
+
+		smp2p_adsp_in: slave-kernel {
+			qcom,entry-name = "slave-kernel";
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	smp2p-cdsp {
+		compatible = "qcom,smp2p";
+		qcom,smem = <94>, <432>;
+		interrupts-extended = <&ipcc IPCC_CLIENT_CDSP
+					     IPCC_MPROC_SIGNAL_SMP2P
+					     IRQ_TYPE_EDGE_RISING>;
+		mboxes = <&ipcc IPCC_CLIENT_CDSP
+				IPCC_MPROC_SIGNAL_SMP2P>;
+
+		qcom,local-pid = <0>;
+		qcom,remote-pid = <5>;
+
+		smp2p_cdsp_out: master-kernel {
+			qcom,entry-name = "master-kernel";
+			#qcom,smem-state-cells = <1>;
+		};
+
+		smp2p_cdsp_in: slave-kernel {
+			qcom,entry-name = "slave-kernel";
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	smp2p-mpss {
+		compatible = "qcom,smp2p";
+		qcom,smem = <435>, <428>;
+
+		interrupts-extended = <&ipcc IPCC_CLIENT_MPSS
+					     IPCC_MPROC_SIGNAL_SMP2P
+					     IRQ_TYPE_EDGE_RISING>;
+		mboxes = <&ipcc IPCC_CLIENT_MPSS
+				IPCC_MPROC_SIGNAL_SMP2P>;
+
+		qcom,local-pid = <0>;
+		qcom,remote-pid = <1>;
+
+		modem_smp2p_out: master-kernel {
+			qcom,entry-name = "master-kernel";
+			#qcom,smem-state-cells = <1>;
+		};
+
+		modem_smp2p_in: slave-kernel {
+			qcom,entry-name = "slave-kernel";
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
 	soc: soc@0 {
 		#address-cells = <2>;
 		#size-cells = <2>;
@@ -398,7 +475,7 @@
 			clock-names = "core";
 		};
 
-		sdhc_1: sdhci@7c4000 {
+		sdhc_1: mmc@7c4000 {
 			compatible = "qcom,sm6350-sdhci", "qcom,sdhci-msm-v5";
 			reg = <0 0x007c4000 0 0x1000>,
 				<0 0x007c5000 0 0x1000>,
@@ -415,7 +492,7 @@
 			clock-names = "iface", "core", "xo";
 			qcom,dll-config = <0x000f642c>;
 			qcom,ddr-config = <0x80040868>;
-			power-domains = <&rpmhpd 0>;
+			power-domains = <&rpmhpd SM6350_CX>;
 			operating-points-v2 = <&sdhc1_opp_table>;
 			bus-width = <8>;
 			non-removable;
@@ -423,7 +500,7 @@
 
 			status = "disabled";
 
-			sdhc1_opp_table: sdhc1-opp-table {
+			sdhc1_opp_table: opp-table {
 				compatible = "operating-points-v2";
 
 				opp-19200000 {
@@ -443,6 +520,99 @@
 			};
 		};
 
+		gpi_dma0: dma-controller@800000 {
+			compatible = "qcom,sm6350-gpi-dma";
+			reg = <0 0x00800000 0 0x60000>;
+			interrupts = <GIC_SPI 244 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 245 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 246 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 247 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 248 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 249 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 250 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 251 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 252 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 253 IRQ_TYPE_LEVEL_HIGH>;
+			dma-channels = <10>;
+			dma-channel-mask = <0x1f>;
+			iommus = <&apps_smmu 0x56 0x0>;
+			#dma-cells = <3>;
+			status = "disabled";
+		};
+
+		qupv3_id_0: geniqup@8c0000 {
+			compatible = "qcom,geni-se-qup";
+			reg = <0x0 0x8c0000 0x0 0x2000>;
+			clock-names = "m-ahb", "s-ahb";
+			clocks = <&gcc GCC_QUPV3_WRAP_0_M_AHB_CLK>,
+				 <&gcc GCC_QUPV3_WRAP_0_S_AHB_CLK>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			iommus = <&apps_smmu 0x43 0x0>;
+			ranges;
+			status = "disabled";
+
+			i2c0: i2c@880000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00880000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c0_default>;
+				interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&gpi_dma0 0 0 QCOM_GPI_I2C>,
+				       <&gpi_dma0 1 0 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_0 0>,
+						<&aggre1_noc MASTER_QUP_0 0 &clk_virt SLAVE_EBI_CH0 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				status = "disabled";
+			};
+
+			i2c2: i2c@888000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00888000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c2_default>;
+				interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&gpi_dma0 0 2 QCOM_GPI_I2C>,
+				       <&gpi_dma0 1 2 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_0 0>,
+						<&aggre1_noc MASTER_QUP_0 0 &clk_virt SLAVE_EBI_CH0 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				status = "disabled";
+			};
+		};
+
+		gpi_dma1: dma-controller@900000 {
+			compatible = "qcom,sm6350-gpi-dma";
+			reg = <0 0x00900000 0 0x60000>;
+			interrupts = <GIC_SPI 645 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 646 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 647 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 648 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 649 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 650 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 651 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 652 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 653 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 654 IRQ_TYPE_LEVEL_HIGH>;
+			dma-channels = <10>;
+			dma-channel-mask = <0x3f>;
+			iommus = <&apps_smmu 0x4d6 0x0>;
+			#dma-cells = <3>;
+			status = "disabled";
+		};
+
 		qupv3_id_1: geniqup@9c0000 {
 			compatible = "qcom,geni-se-qup";
 			reg = <0x0 0x9c0000 0x0 0x2000>;
@@ -455,16 +625,224 @@
 			ranges;
 			status = "disabled";
 
-			uart2: serial@98c000 {
+			i2c6: i2c@980000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00980000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c6_default>;
+				interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&gpi_dma1 0 0 QCOM_GPI_I2C>,
+				       <&gpi_dma1 1 0 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_1 0>,
+						<&aggre2_noc MASTER_QUP_1 0 &clk_virt SLAVE_EBI_CH0 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				status = "disabled";
+			};
+
+			i2c7: i2c@984000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00984000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c7_default>;
+				interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&gpi_dma1 0 1 QCOM_GPI_I2C>,
+				       <&gpi_dma1 1 1 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_1 0>,
+						<&aggre2_noc MASTER_QUP_1 0 &clk_virt SLAVE_EBI_CH0 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				status = "disabled";
+			};
+
+			i2c8: i2c@988000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00988000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c8_default>;
+				interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&gpi_dma1 0 2 QCOM_GPI_I2C>,
+				       <&gpi_dma1 1 2 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_1 0>,
+						<&aggre2_noc MASTER_QUP_1 0 &clk_virt SLAVE_EBI_CH0 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				status = "disabled";
+			};
+
+			uart9: serial@98c000 {
 				compatible = "qcom,geni-debug-uart";
 				reg = <0 0x98c000 0 0x4000>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
 				pinctrl-names = "default";
-				pinctrl-0 = <&qup_uart2_default>;
+				pinctrl-0 = <&qup_uart9_default>;
 				interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_1 0>;
+				interconnect-names = "qup-core", "qup-config";
+				status = "disabled";
+			};
+
+			i2c10: i2c@990000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00990000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c10_default>;
+				interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&gpi_dma1 0 4 QCOM_GPI_I2C>,
+				       <&gpi_dma1 1 4 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_QUP_1 0>,
+						<&aggre2_noc MASTER_QUP_1 0 &clk_virt SLAVE_EBI_CH0 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
 				status = "disabled";
 			};
+
+		};
+
+		config_noc: interconnect@1500000 {
+			compatible = "qcom,sm6350-config-noc";
+			reg = <0 0x01500000 0 0x28000>;
+			#interconnect-cells = <2>;
+			qcom,bcm-voters = <&apps_bcm_voter>;
+		};
+
+		system_noc: interconnect@1620000 {
+			compatible = "qcom,sm6350-system-noc";
+			reg = <0 0x01620000 0 0x17080>;
+			#interconnect-cells = <2>;
+			qcom,bcm-voters = <&apps_bcm_voter>;
+
+			clk_virt: interconnect-clk-virt {
+				compatible = "qcom,sm6350-clk-virt";
+				#interconnect-cells = <2>;
+				qcom,bcm-voters = <&apps_bcm_voter>;
+			};
+		};
+
+		aggre1_noc: interconnect@16e0000 {
+			compatible = "qcom,sm6350-aggre1-noc";
+			reg = <0 0x016e0000 0 0x15080>;
+			#interconnect-cells = <2>;
+			qcom,bcm-voters = <&apps_bcm_voter>;
+		};
+
+		aggre2_noc: interconnect@1700000 {
+			compatible = "qcom,sm6350-aggre2-noc";
+			reg = <0 0x01700000 0 0x1f880>;
+			#interconnect-cells = <2>;
+			qcom,bcm-voters = <&apps_bcm_voter>;
+
+			compute_noc: interconnect-compute-noc {
+				compatible = "qcom,sm6350-compute-noc";
+				#interconnect-cells = <2>;
+				qcom,bcm-voters = <&apps_bcm_voter>;
+			};
+		};
+
+		mmss_noc: interconnect@1740000 {
+			compatible = "qcom,sm6350-mmss-noc";
+			reg = <0 0x01740000 0 0x1c100>;
+			#interconnect-cells = <2>;
+			qcom,bcm-voters = <&apps_bcm_voter>;
+		};
+
+		ufs_mem_hc: ufs@1d84000 {
+			compatible = "qcom,sm6350-ufshc", "qcom,ufshc",
+				     "jedec,ufs-2.0";
+			reg = <0 0x01d84000 0 0x3000>,
+			      <0 0x01d90000 0 0x8000>;
+			reg-names = "std", "ice";
+			interrupts = <GIC_SPI 265 IRQ_TYPE_LEVEL_HIGH>;
+			phys = <&ufs_mem_phy_lanes>;
+			phy-names = "ufsphy";
+			lanes-per-direction = <2>;
+			#reset-cells = <1>;
+			resets = <&gcc GCC_UFS_PHY_BCR>;
+			reset-names = "rst";
+
+			power-domains = <&gcc UFS_PHY_GDSC>;
+
+			iommus = <&apps_smmu 0x80 0x0>;
+
+			clock-names = "core_clk",
+				      "bus_aggr_clk",
+				      "iface_clk",
+				      "core_clk_unipro",
+				      "ref_clk",
+				      "tx_lane0_sync_clk",
+				      "rx_lane0_sync_clk",
+				      "rx_lane1_sync_clk",
+				      "ice_core_clk";
+			clocks = <&gcc GCC_UFS_PHY_AXI_CLK>,
+				 <&gcc GCC_AGGRE_UFS_PHY_AXI_CLK>,
+				 <&gcc GCC_UFS_PHY_AHB_CLK>,
+				 <&gcc GCC_UFS_PHY_UNIPRO_CORE_CLK>,
+				 <&rpmhcc RPMH_QLINK_CLK>,
+				 <&gcc GCC_UFS_PHY_TX_SYMBOL_0_CLK>,
+				 <&gcc GCC_UFS_PHY_RX_SYMBOL_0_CLK>,
+				 <&gcc GCC_UFS_PHY_RX_SYMBOL_1_CLK>,
+				 <&gcc GCC_UFS_PHY_ICE_CORE_CLK>;
+			freq-table-hz =
+				<50000000 200000000>,
+				<0 0>,
+				<0 0>,
+				<37500000 150000000>,
+				<75000000 300000000>,
+				<0 0>,
+				<0 0>,
+				<0 0>,
+				<0 0>;
+
+			status = "disabled";
+		};
+
+		ufs_mem_phy: phy@1d87000 {
+			compatible = "qcom,sm6350-qmp-ufs-phy";
+			reg = <0 0x01d87000 0 0x18c>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+
+			clock-names = "ref",
+				      "ref_aux";
+			clocks = <&gcc GCC_UFS_MEM_CLKREF_CLK>,
+				 <&gcc GCC_UFS_PHY_PHY_AUX_CLK>;
+
+			resets = <&ufs_mem_hc 0>;
+			reset-names = "ufsphy";
+
+			status = "disabled";
+
+			ufs_mem_phy_lanes: phy@1d87400 {
+				reg = <0 0x01d87400 0 0x128>,
+				      <0 0x01d87600 0 0x1fc>,
+				      <0 0x01d87c00 0 0x1dc>,
+				      <0 0x01d87800 0 0x128>,
+				      <0 0x01d87a00 0 0x1fc>;
+				#phy-cells = <0>;
+			};
 		};
 
 		tcsr_mutex: hwlock@1f40000 {
@@ -473,7 +851,212 @@
 			#hwlock-cells = <1>;
 		};
 
-		sdhc_2: sdhci@8804000 {
+		adsp: remoteproc@3000000 {
+			compatible = "qcom,sm6350-adsp-pas";
+			reg = <0 0x03000000 0 0x100>;
+
+			interrupts-extended = <&pdc 6 IRQ_TYPE_LEVEL_HIGH>,
+					      <&smp2p_adsp_in 0 IRQ_TYPE_EDGE_RISING>,
+					      <&smp2p_adsp_in 1 IRQ_TYPE_EDGE_RISING>,
+					      <&smp2p_adsp_in 2 IRQ_TYPE_EDGE_RISING>,
+					      <&smp2p_adsp_in 3 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "wdog", "fatal", "ready",
+					  "handover", "stop-ack";
+
+			clocks = <&rpmhcc RPMH_CXO_CLK>;
+			clock-names = "xo";
+
+			power-domains = <&rpmhpd SM6350_LCX>,
+					<&rpmhpd SM6350_LMX>;
+			power-domain-names = "lcx", "lmx";
+
+			memory-region = <&pil_adsp_mem>;
+
+			qcom,qmp = <&aoss_qmp>;
+
+			qcom,smem-states = <&smp2p_adsp_out 0>;
+			qcom,smem-state-names = "stop";
+
+			status = "disabled";
+
+			glink-edge {
+				interrupts-extended = <&ipcc IPCC_CLIENT_LPASS
+							     IPCC_MPROC_SIGNAL_GLINK_QMP
+							     IRQ_TYPE_EDGE_RISING>;
+				mboxes = <&ipcc IPCC_CLIENT_LPASS
+						IPCC_MPROC_SIGNAL_GLINK_QMP>;
+
+				label = "lpass";
+				qcom,remote-pid = <2>;
+
+				fastrpc {
+					compatible = "qcom,fastrpc";
+					qcom,glink-channels = "fastrpcglink-apps-dsp";
+					label = "adsp";
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					compute-cb@3 {
+						compatible = "qcom,fastrpc-compute-cb";
+						reg = <3>;
+						iommus = <&apps_smmu 0x1003 0x0>;
+					};
+
+					compute-cb@4 {
+						compatible = "qcom,fastrpc-compute-cb";
+						reg = <4>;
+						iommus = <&apps_smmu 0x1004 0x0>;
+					};
+
+					compute-cb@5 {
+						compatible = "qcom,fastrpc-compute-cb";
+						reg = <5>;
+						iommus = <&apps_smmu 0x1005 0x0>;
+						qcom,nsessions = <5>;
+					};
+				};
+			};
+		};
+
+		mpss: remoteproc@4080000 {
+			compatible = "qcom,sm6350-mpss-pas";
+			reg = <0x0 0x04080000 0x0 0x4040>;
+
+			interrupts-extended = <&intc GIC_SPI 136 IRQ_TYPE_EDGE_RISING>,
+					      <&modem_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
+					      <&modem_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
+					      <&modem_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
+					      <&modem_smp2p_in 3 IRQ_TYPE_EDGE_RISING>,
+					      <&modem_smp2p_in 7 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "wdog", "fatal", "ready", "handover",
+					  "stop-ack", "shutdown-ack";
+
+			clocks = <&rpmhcc RPMH_CXO_CLK>;
+			clock-names = "xo";
+
+			power-domains = <&rpmhpd SM6350_CX>,
+					<&rpmhpd SM6350_MSS>;
+			power-domain-names = "cx", "mss";
+
+			memory-region = <&pil_modem_mem>;
+
+			qcom,qmp = <&aoss_qmp>;
+
+			qcom,smem-states = <&modem_smp2p_out 0>;
+			qcom,smem-state-names = "stop";
+
+			status = "disabled";
+
+			glink-edge {
+				interrupts-extended = <&ipcc IPCC_CLIENT_MPSS
+							     IPCC_MPROC_SIGNAL_GLINK_QMP
+							     IRQ_TYPE_EDGE_RISING>;
+				mboxes = <&ipcc IPCC_CLIENT_MPSS
+						IPCC_MPROC_SIGNAL_GLINK_QMP>;
+				label = "modem";
+				qcom,remote-pid = <1>;
+			};
+		};
+
+		cdsp: remoteproc@8300000 {
+			compatible = "qcom,sm6350-cdsp-pas";
+			reg = <0 0x08300000 0 0x10000>;
+
+			interrupts-extended = <&intc GIC_SPI 578 IRQ_TYPE_LEVEL_HIGH>,
+					      <&smp2p_cdsp_in 0 IRQ_TYPE_EDGE_RISING>,
+					      <&smp2p_cdsp_in 1 IRQ_TYPE_EDGE_RISING>,
+					      <&smp2p_cdsp_in 2 IRQ_TYPE_EDGE_RISING>,
+					      <&smp2p_cdsp_in 3 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "wdog", "fatal", "ready",
+					  "handover", "stop-ack";
+
+			clocks = <&rpmhcc RPMH_CXO_CLK>;
+			clock-names = "xo";
+
+			power-domains = <&rpmhpd SM6350_CX>,
+					<&rpmhpd SM6350_MX>;
+			power-domain-names = "cx", "mx";
+
+			memory-region = <&pil_cdsp_mem>;
+
+			qcom,qmp = <&aoss_qmp>;
+
+			qcom,smem-states = <&smp2p_cdsp_out 0>;
+			qcom,smem-state-names = "stop";
+
+			status = "disabled";
+
+			glink-edge {
+				interrupts-extended = <&ipcc IPCC_CLIENT_CDSP
+							     IPCC_MPROC_SIGNAL_GLINK_QMP
+							     IRQ_TYPE_EDGE_RISING>;
+				mboxes = <&ipcc IPCC_CLIENT_CDSP
+						IPCC_MPROC_SIGNAL_GLINK_QMP>;
+
+				label = "cdsp";
+				qcom,remote-pid = <5>;
+
+				fastrpc {
+					compatible = "qcom,fastrpc";
+					qcom,glink-channels = "fastrpcglink-apps-dsp";
+					label = "cdsp";
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					compute-cb@1 {
+						compatible = "qcom,fastrpc-compute-cb";
+						reg = <1>;
+						iommus = <&apps_smmu 0x1401 0x20>;
+					};
+
+					compute-cb@2 {
+						compatible = "qcom,fastrpc-compute-cb";
+						reg = <2>;
+						iommus = <&apps_smmu 0x1402 0x20>;
+					};
+
+					compute-cb@3 {
+						compatible = "qcom,fastrpc-compute-cb";
+						reg = <3>;
+						iommus = <&apps_smmu 0x1403 0x20>;
+					};
+
+					compute-cb@4 {
+						compatible = "qcom,fastrpc-compute-cb";
+						reg = <4>;
+						iommus = <&apps_smmu 0x1404 0x20>;
+					};
+
+					compute-cb@5 {
+						compatible = "qcom,fastrpc-compute-cb";
+						reg = <5>;
+						iommus = <&apps_smmu 0x1405 0x20>;
+					};
+
+					compute-cb@6 {
+						compatible = "qcom,fastrpc-compute-cb";
+						reg = <6>;
+						iommus = <&apps_smmu 0x1406 0x20>;
+					};
+
+					compute-cb@7 {
+						compatible = "qcom,fastrpc-compute-cb";
+						reg = <7>;
+						iommus = <&apps_smmu 0x1407 0x20>;
+					};
+
+					compute-cb@8 {
+						compatible = "qcom,fastrpc-compute-cb";
+						reg = <8>;
+						iommus = <&apps_smmu 0x1408 0x20>;
+					};
+
+					/* note: secure cb9 in downstream */
+				};
+			};
+		};
+
+		sdhc_2: mmc@8804000 {
 			compatible = "qcom,sm6350-sdhci", "qcom,sdhci-msm-v5";
 			reg = <0 0x08804000 0 0x1000>;
 
@@ -485,25 +1068,33 @@
 				 <&gcc GCC_SDCC2_APPS_CLK>,
 				 <&rpmhcc RPMH_CXO_CLK>;
 			clock-names = "iface", "core", "xo";
+			interconnects = <&aggre2_noc MASTER_SDCC_2 0 &clk_virt SLAVE_EBI_CH0 0>,
+					<&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_SDCC_2 0>;
+			interconnect-names = "sdhc-ddr", "cpu-sdhc";
+
 			qcom,dll-config = <0x0007642c>;
 			qcom,ddr-config = <0x80040868>;
-			power-domains = <&rpmhpd 0>;
+			power-domains = <&rpmhpd SM6350_CX>;
 			operating-points-v2 = <&sdhc2_opp_table>;
 			bus-width = <4>;
 
 			status = "disabled";
 
-			sdhc2_opp_table: sdhc2-opp-table {
+			sdhc2_opp_table: opp-table {
 				compatible = "operating-points-v2";
 
 				opp-100000000 {
 					opp-hz = /bits/ 64 <100000000>;
 					required-opps = <&rpmhpd_opp_svs_l1>;
+					opp-peak-kBps = <790000 131000>;
+					opp-avg-kBps = <50000 50000>;
 				};
 
 				opp-202000000 {
 					opp-hz = /bits/ 64 <202000000>;
 					required-opps = <&rpmhpd_opp_nom>;
+					opp-peak-kBps = <3190000 294000>;
+					opp-avg-kBps = <261438 300000>;
 				};
 			};
 		};
@@ -531,10 +1122,10 @@
 			ranges;
 
 			clocks = <&gcc GCC_USB3_PRIM_PHY_AUX_CLK>,
+				 <&xo_board>,
 				 <&rpmhcc RPMH_QLINK_CLK>,
-				 <&gcc GCC_USB3_PRIM_PHY_COM_AUX_CLK>,
-				 <&xo_board>;
-			clock-names = "aux", "ref", "com_aux", "cfg_ahb";
+				 <&gcc GCC_USB3_PRIM_PHY_COM_AUX_CLK>;
+			clock-names = "aux", "cfg_ahb", "ref", "com_aux";
 
 			resets = <&gcc GCC_USB3_DP_PHY_PRIM_BCR>,
 				 <&gcc GCC_USB3_PHY_PRIM_BCR>;
@@ -569,12 +1160,33 @@
 			};
 		};
 
+		dc_noc: interconnect@9160000 {
+			compatible = "qcom,sm6350-dc-noc";
+			reg = <0 0x09160000 0 0x3200>;
+			#interconnect-cells = <2>;
+			qcom,bcm-voters = <&apps_bcm_voter>;
+		};
+
 		system-cache-controller@9200000 {
 			compatible = "qcom,sm6350-llcc";
 			reg = <0 0x09200000 0 0x50000>, <0 0x09600000 0 0x50000>;
 			reg-names = "llcc_base", "llcc_broadcast_base";
 		};
 
+		gem_noc: interconnect@9680000 {
+			compatible = "qcom,sm6350-gem-noc";
+			reg = <0 0x09680000 0 0x3e200>;
+			#interconnect-cells = <2>;
+			qcom,bcm-voters = <&apps_bcm_voter>;
+		};
+
+		npu_noc: interconnect@9990000 {
+			compatible = "qcom,sm6350-npu-noc";
+			reg = <0 0x09990000 0 0x1600>;
+			#interconnect-cells = <2>;
+			qcom,bcm-voters = <&apps_bcm_voter>;
+		};
+
 		usb_1: usb@a6f8800 {
 			compatible = "qcom,sm6350-dwc3", "qcom,dwc3";
 			reg = <0 0x0a6f8800 0 0x400>;
@@ -586,22 +1198,30 @@
 			clocks = <&gcc GCC_CFG_NOC_USB3_PRIM_AXI_CLK>,
 				 <&gcc GCC_USB30_PRIM_MASTER_CLK>,
 				 <&gcc GCC_AGGRE_USB3_PRIM_AXI_CLK>,
-				 <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
-				 <&gcc GCC_USB30_PRIM_SLEEP_CLK>;
-			clock-names = "cfg_noc", "core", "iface", "mock_utmi",
-				      "sleep";
+				 <&gcc GCC_USB30_PRIM_SLEEP_CLK>,
+				 <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>;
+			clock-names = "cfg_noc",
+				      "core",
+				      "iface",
+				      "sleep",
+				      "mock_utmi";
 
 			interrupts-extended = <&intc GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>,
-					      <&pdc 14 IRQ_TYPE_EDGE_BOTH>,
+					      <&pdc 17 IRQ_TYPE_LEVEL_HIGH>,
 					      <&pdc 15 IRQ_TYPE_EDGE_BOTH>,
-					      <&pdc 17 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "hs_phy_irq", "dp_hs_phy_irq",
-					  "dm_hs_phy_irq", "ss_phy_irq";
+					      <&pdc 14 IRQ_TYPE_EDGE_BOTH>;
+
+			interrupt-names = "hs_phy_irq", "ss_phy_irq",
+					  "dm_hs_phy_irq", "dp_hs_phy_irq";
 
 			power-domains = <&gcc USB30_PRIM_GDSC>;
 
 			resets = <&gcc GCC_USB30_PRIM_BCR>;
 
+			interconnects = <&aggre2_noc MASTER_USB3 0 &clk_virt SLAVE_EBI_CH0 0>,
+					<&gem_noc MASTER_AMPSS_M0 0 &config_noc SLAVE_USB3 0>;
+			interconnect-names = "usb-ddr", "apps-usb";
+
 			usb_1_dwc3: usb@a600000 {
 				compatible = "snps,dwc3";
 				reg = <0 0x0a600000 0 0xcd00>;
@@ -631,7 +1251,7 @@
 			reg = <0 0x0c263000 0 0x1ff>, /* TM */
 			      <0 0x0c222000 0 0x8>; /* SROT */
 			#qcom,sensors = <16>;
-			interrupts = <&pdc 26 IRQ_TYPE_LEVEL_HIGH>,
+			interrupts-extended = <&pdc 26 IRQ_TYPE_LEVEL_HIGH>,
 				     <&pdc 28 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "uplow", "critical";
 			#thermal-sensor-cells = <1>;
@@ -642,7 +1262,7 @@
 			reg = <0 0x0c265000 0 0x1ff>, /* TM */
 			      <0 0x0c223000 0 0x8>; /* SROT */
 			#qcom,sensors = <16>;
-			interrupts = <&pdc 27 IRQ_TYPE_LEVEL_HIGH>,
+			interrupts-extended = <&pdc 27 IRQ_TYPE_LEVEL_HIGH>,
 				     <&pdc 29 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "uplow", "critical";
 			#thermal-sensor-cells = <1>;
@@ -656,7 +1276,6 @@
 			mboxes = <&ipcc IPCC_CLIENT_AOP IPCC_MPROC_SIGNAL_GLINK_QMP>;
 
 			#clock-cells = <0>;
-			#power-domain-cells = <1>;
 		};
 
 		spmi_bus: spmi@c440000 {
@@ -695,12 +1314,54 @@
 			#interrupt-cells = <2>;
 			gpio-ranges = <&tlmm 0 0 157>;
 
-			qup_uart2_default: qup-uart2-default {
+			qup_uart9_default: qup-uart9-default-state {
 				pins = "gpio25", "gpio26";
 				function = "qup13_f2";
 				drive-strength = <2>;
 				bias-disable;
 			};
+
+			qup_i2c0_default: qup-i2c0-default-state {
+				pins = "gpio0", "gpio1";
+				function = "qup00";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			qup_i2c2_default: qup-i2c2-default-state {
+				pins = "gpio45", "gpio46";
+				function = "qup02";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			qup_i2c6_default: qup-i2c6-default-state {
+				pins = "gpio13", "gpio14";
+				function = "qup10";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			qup_i2c7_default: qup-i2c7-default-state {
+				pins = "gpio27", "gpio28";
+				function = "qup11";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			qup_i2c8_default: qup-i2c8-default-state {
+				pins = "gpio19", "gpio20";
+				function = "qup12";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			qup_i2c10_default: qup-i2c10-default-state {
+				pins = "gpio4", "gpio5";
+				function = "qup14";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
 		};
 
 		apps_smmu: iommu@15000000 {
@@ -811,61 +1472,83 @@
 			compatible = "arm,armv7-timer-mem";
 			reg = <0x0 0x17c20000 0x0 0x1000>;
 			clock-frequency = <19200000>;
-			#address-cells = <2>;
-			#size-cells = <2>;
-			ranges;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0 0 0x20000000>;
 
 			frame@17c21000 {
 				frame-number = <0>;
 				interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
 					     <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0x0 0x17c21000 0x0 0x1000>,
-				      <0x0 0x17c22000 0x0 0x1000>;
+				reg = <0x17c21000 0x1000>,
+				      <0x17c22000 0x1000>;
 			};
 
 			frame@17c23000 {
 				frame-number = <1>;
 				interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0x0 0x17c23000 0x0 0x1000>;
+				reg = <0x17c23000 0x1000>;
 				status = "disabled";
 			};
 
 			frame@17c25000 {
 				frame-number = <2>;
 				interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0x0 0x17c25000 0x0 0x1000>;
+				reg = <0x17c25000 0x1000>;
 				status = "disabled";
 			};
 
 			frame@17c27000 {
 				frame-number = <3>;
 				interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0x0 0x17c27000 0x0 0x1000>;
+				reg = <0x17c27000 0x1000>;
 				status = "disabled";
 			};
 
 			frame@17c29000 {
 				frame-number = <4>;
 				interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0x0 0x17c29000 0x0 0x1000>;
+				reg = <0x17c29000 0x1000>;
 				status = "disabled";
 			};
 
 			frame@17c2b000 {
 				frame-number = <5>;
 				interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0x0 0x17c2b000 0x0 0x1000>;
+				reg = <0x17c2b000 0x1000>;
 				status = "disabled";
 			};
 
 			frame@17c2d000 {
 				frame-number = <6>;
 				interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0x0 0x17c2d000 0x0 0x1000>;
+				reg = <0x17c2d000 0x1000>;
 				status = "disabled";
 			};
 		};
 
+		wifi: wifi@18800000 {
+			compatible = "qcom,wcn3990-wifi";
+			reg = <0 0x18800000 0 0x800000>;
+			reg-names = "membase";
+			memory-region = <&wlan_fw_mem>;
+			interrupts = <GIC_SPI 414 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 415 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 416 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 417 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 418 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 419 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 420 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 421 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 422 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 423 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 424 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 425 IRQ_TYPE_LEVEL_HIGH>;
+			iommus = <&apps_smmu 0x20 0x1>;
+			qcom,msa-fixed-perm;
+			status = "disabled";
+		};
+
 		apps_rsc: rsc@18200000 {
 			compatible = "qcom,rpmh-rsc";
 			label = "apps_rsc";
@@ -938,7 +1621,7 @@
 				};
 			};
 
-			apps_bcm_voter: bcm_voter {
+			apps_bcm_voter: bcm-voter {
 				compatible = "qcom,bcm-voter";
 			};
 		};
diff --git a/arch/arm64/boot/dts/qcom/sm7225-fairphone-fp4.dts b/arch/arm64/boot/dts/qcom/sm7225-fairphone-fp4.dts
index 8d6fd22873e0..30c94fd4fe61 100644
--- a/arch/arm64/boot/dts/qcom/sm7225-fairphone-fp4.dts
+++ b/arch/arm64/boot/dts/qcom/sm7225-fairphone-fp4.dts
@@ -10,18 +10,21 @@
 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
 #include "sm7225.dtsi"
+#include "pm6150l.dtsi"
 #include "pm6350.dtsi"
+#include "pm7250b.dtsi"
 
 / {
 	model = "Fairphone 4";
 	compatible = "fairphone,fp4", "qcom,sm7225";
+	chassis-type = "handset";
 
 	/* required for bootloader to select correct board */
 	qcom,msm-id = <434 0x10000>, <459 0x10000>;
 	qcom,board-id = <8 32>;
 
 	aliases {
-		serial0 = &uart2;
+		serial0 = &uart9;
 	};
 
 	chosen {
@@ -46,12 +49,63 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&gpio_keys_pin>;
 
-		volume-up {
+		key-volume-up {
 			label = "volume_up";
 			linux,code = <KEY_VOLUMEUP>;
 			gpios = <&pm6350_gpios 2 GPIO_ACTIVE_LOW>;
 		};
 	};
+
+	reserved-memory {
+		/*
+		 * The rmtfs memory region in downstream is 'dynamically allocated'
+		 * but given the same address every time. Hard code it as this address is
+		 * where the modem firmware expects it to be.
+		 */
+		memory@efe01000 {
+			compatible = "qcom,rmtfs-mem";
+			reg = <0 0xefe01000 0 0x600000>;
+			no-map;
+
+			qcom,client-id = <1>;
+			qcom,vmid = <15>;
+		};
+	};
+
+	thermal-zones {
+		chg-skin-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&pm7250b_adc_tm 0>;
+
+			trips {
+				active-config0 {
+					temperature = <125000>;
+					hysteresis = <1000>;
+					type = "passive";
+				};
+			};
+		};
+
+		conn-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&pm7250b_adc_tm 1>;
+
+			trips {
+				active-config0 {
+					temperature = <125000>;
+					hysteresis = <1000>;
+					type = "passive";
+				};
+			};
+		};
+	};
+};
+
+&adsp {
+	status = "okay";
+	firmware-name = "qcom/sm7225/fairphone4/adsp.mdt";
 };
 
 &apps_rsc {
@@ -268,8 +322,55 @@
 	};
 };
 
+&cdsp {
+	status = "okay";
+	firmware-name = "qcom/sm7225/fairphone4/cdsp.mdt";
+};
+
+&i2c10 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	haptics@5a {
+		compatible = "awinic,aw8695";
+		reg = <0x5a>;
+		interrupts-extended = <&tlmm 85 IRQ_TYPE_EDGE_FALLING>;
+		reset-gpios = <&tlmm 90 GPIO_ACTIVE_HIGH>;
+
+		awinic,f0-preset = <2350>;
+		awinic,f0-coefficient = <260>;
+		awinic,f0-calibration-percent = <7>;
+		awinic,drive-level = <125>;
+
+		awinic,f0-detection-play-time = <5>;
+		awinic,f0-detection-wait-time = <3>;
+		awinic,f0-detection-repeat = <2>;
+		awinic,f0-detection-trace = <15>;
+
+		awinic,boost-debug = /bits/ 8 <0x30 0xeb 0xd4>;
+		awinic,tset = /bits/ 8 <0x12>;
+		awinic,r-spare = /bits/ 8 <0x68>;
+
+		awinic,bemf-upper-threshold = <4104>;
+		awinic,bemf-lower-threshold = <1016>;
+	};
+};
+
+&mpss {
+	status = "okay";
+	firmware-name = "qcom/sm7225/fairphone4/modem.mdt";
+};
+
+&pm6150l_wled {
+	status = "okay";
+
+	qcom,switching-freq = <800>;
+	qcom,current-limit-microamp = <20000>;
+	qcom,num-strings = <2>;
+};
+
 &pm6350_gpios {
-	gpio_keys_pin: gpio-keys-pin {
+	gpio_keys_pin: gpio-keys-state {
 		pins = "gpio2";
 		function = PMIC_GPIO_FUNC_NORMAL;
 		bias-pull-up;
@@ -283,6 +384,42 @@
 	linux,code = <KEY_VOLUMEDOWN>;
 };
 
+&pm7250b_adc {
+	adc-chan@4d {
+		reg = <ADC5_AMUX_THM1_100K_PU>;
+		qcom,ratiometric;
+		qcom,hw-settle-time = <200>;
+		qcom,pre-scaling = <1 1>;
+		label = "charger_skin_therm";
+	};
+
+	adc-chan@4f {
+		reg = <ADC5_AMUX_THM3_100K_PU>;
+		qcom,ratiometric;
+		qcom,hw-settle-time = <200>;
+		qcom,pre-scaling = <1 1>;
+		label = "conn_therm";
+	};
+};
+
+&pm7250b_adc_tm {
+	status = "okay";
+
+	charger-skin-therm@0 {
+		reg = <0>;
+		io-channels = <&pm7250b_adc ADC5_AMUX_THM1_100K_PU>;
+		qcom,ratiometric;
+		qcom,hw-settle-time-us = <200>;
+	};
+
+	conn-therm@1 {
+		reg = <1>;
+		io-channels = <&pm7250b_adc ADC5_AMUX_THM3_100K_PU>;
+		qcom,ratiometric;
+		qcom,hw-settle-time-us = <200>;
+	};
+};
+
 &qupv3_id_1 {
 	status = "okay";
 };
@@ -291,8 +428,26 @@
 	gpio-reserved-ranges = <13 4>, <56 2>;
 };
 
-&uart2 {
+&uart9 {
+	status = "okay";
+};
+
+&ufs_mem_hc {
+	status = "okay";
+
+	reset-gpios = <&tlmm 156 GPIO_ACTIVE_LOW>;
+
+	vcc-supply = <&vreg_l7e>;
+	vcc-max-microamp = <800000>;
+	vccq2-supply = <&vreg_l12a>;
+	vccq2-max-microamp = <800000>;
+};
+
+&ufs_mem_phy {
 	status = "okay";
+
+	vdda-phy-supply = <&vreg_l18a>;
+	vdda-pll-supply = <&vreg_l22a>;
 };
 
 &usb_1 {
@@ -318,3 +473,13 @@
 	vdda-phy-supply = <&vreg_l22a>;
 	vdda-pll-supply = <&vreg_l16a>;
 };
+
+&wifi {
+	status = "okay";
+
+	vdd-0.8-cx-mx-supply = <&vreg_l4a>;
+	vdd-1.8-xo-supply = <&vreg_l7a>;
+	vdd-1.3-rfa-supply = <&vreg_l2e>;
+	vdd-3.3-ch0-supply = <&vreg_l10e>;
+	vdd-3.3-ch1-supply = <&vreg_l11e>;
+};
diff --git a/arch/arm64/boot/dts/qcom/sm8150-hdk.dts b/arch/arm64/boot/dts/qcom/sm8150-hdk.dts
index 37ddca0f0223..3331ee957d64 100644
--- a/arch/arm64/boot/dts/qcom/sm8150-hdk.dts
+++ b/arch/arm64/boot/dts/qcom/sm8150-hdk.dts
@@ -44,10 +44,10 @@
 		vin-supply = <&vph_pwr>;
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
-		vol-up {
+		key-vol-up {
 			label = "Volume Up";
 			linux,code = <KEY_VOLUMEUP>;
 			gpios = <&pm8150_gpios 6 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm64/boot/dts/qcom/sm8150-microsoft-surface-duo.dts b/arch/arm64/boot/dts/qcom/sm8150-microsoft-surface-duo.dts
index 5901c28e6696..bb278ecac3fa 100644
--- a/arch/arm64/boot/dts/qcom/sm8150-microsoft-surface-duo.dts
+++ b/arch/arm64/boot/dts/qcom/sm8150-microsoft-surface-duo.dts
@@ -49,10 +49,10 @@
 		vin-supply = <&vph_pwr>;
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
-		vol_up {
+		key-vol-up {
 			label = "Volume Up";
 			gpios = <&pm8150_gpios 6 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_VOLUMEUP>;
@@ -430,18 +430,8 @@
 	/* MAX34417 @ 0x1e */
 };
 
-&pon {
-	pwrkey {
-		status = "okay";
-	};
-
-	resin {
-		compatible = "qcom,pm8941-resin";
-		interrupts = <0x0 0x8 0x1 IRQ_TYPE_EDGE_BOTH>;
-		debounce = <15625>;
-		bias-pull-up;
-		linux,code = <KEY_VOLUMEDOWN>;
-	};
+&pon_pwrkey {
+	status = "okay";
 };
 
 &qupv3_id_0 {
@@ -476,6 +466,12 @@
 	firmware-name = "qcom/sm8150/microsoft/slpi.mdt";
 };
 
+&pon_resin {
+	status = "okay";
+
+	linux,code = <KEY_VOLUMEDOWN>;
+};
+
 &tlmm {
 	gpio-reserved-ranges = <126 4>;
 
diff --git a/arch/arm64/boot/dts/qcom/sm8150.dtsi b/arch/arm64/boot/dts/qcom/sm8150.dtsi
index 81b4ff2cc4cd..cef8c4f4f0ff 100644
--- a/arch/arm64/boot/dts/qcom/sm8150.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8150.dtsi
@@ -288,7 +288,7 @@
 		};
 	};
 
-	cpu0_opp_table: cpu0_opp_table {
+	cpu0_opp_table: opp-table-cpu0 {
 		compatible = "operating-points-v2";
 		opp-shared;
 
@@ -383,7 +383,7 @@
 		};
 	};
 
-	cpu4_opp_table: cpu4_opp_table {
+	cpu4_opp_table: opp-table-cpu4 {
 		compatible = "operating-points-v2";
 		opp-shared;
 
@@ -473,7 +473,7 @@
 		};
 	};
 
-	cpu7_opp_table: cpu7_opp_table {
+	cpu7_opp_table: opp-table-cpu7 {
 		compatible = "operating-points-v2";
 		opp-shared;
 
@@ -585,12 +585,6 @@
 		};
 	};
 
-	tcsr_mutex: hwlock {
-		compatible = "qcom,tcsr-mutex";
-		syscon = <&tcsr_mutex_regs 0 0x1000>;
-		#hwlock-cells = <1>;
-	};
-
 	memory@80000000 {
 		device_type = "memory";
 		/* We expect the bootloader to fill in the size */
@@ -915,6 +909,33 @@
 			status = "disabled";
 		};
 
+		ethernet: ethernet@20000 {
+			compatible = "qcom,sm8150-ethqos";
+			reg = <0x0 0x00020000 0x0 0x10000>,
+			      <0x0 0x00036000 0x0 0x100>;
+			reg-names = "stmmaceth", "rgmii";
+			clock-names = "stmmaceth", "pclk", "ptp_ref", "rgmii";
+			clocks = <&gcc GCC_EMAC_AXI_CLK>,
+				<&gcc GCC_EMAC_SLV_AHB_CLK>,
+				<&gcc GCC_EMAC_PTP_CLK>,
+				<&gcc GCC_EMAC_RGMII_CLK>;
+			interrupts = <GIC_SPI 689 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 699 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "macirq", "eth_lpi";
+
+			power-domains = <&gcc EMAC_GDSC>;
+			resets = <&gcc GCC_EMAC_BCR>;
+
+			iommus = <&apps_smmu 0x3C0 0x0>;
+
+			snps,tso;
+			rx-fifo-depth = <4096>;
+			tx-fifo-depth = <4096>;
+
+			status = "disabled";
+		};
+
+
 		qupv3_id_0: geniqup@8c0000 {
 			compatible = "qcom,geni-se-qup";
 			reg = <0x0 0x008c0000 0x0 0x6000>;
@@ -932,6 +953,9 @@
 				reg = <0 0x00880000 0 0x4000>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
+				dmas = <&gpi_dma0 0 0 QCOM_GPI_I2C>,
+				       <&gpi_dma0 1 0 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
 				pinctrl-names = "default";
 				pinctrl-0 = <&qup_i2c0_default>;
 				interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
@@ -946,6 +970,9 @@
 				reg-names = "se";
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
+				dmas = <&gpi_dma0 0 0 QCOM_GPI_SPI>,
+				       <&gpi_dma0 1 0 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
 				pinctrl-names = "default";
 				pinctrl-0 = <&qup_spi0_default>;
 				interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
@@ -960,6 +987,9 @@
 				reg = <0 0x00884000 0 0x4000>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
+				dmas = <&gpi_dma0 0 1 QCOM_GPI_I2C>,
+				       <&gpi_dma0 1 1 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
 				pinctrl-names = "default";
 				pinctrl-0 = <&qup_i2c1_default>;
 				interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
@@ -974,6 +1004,9 @@
 				reg-names = "se";
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
+				dmas = <&gpi_dma0 0 1 QCOM_GPI_SPI>,
+				       <&gpi_dma0 1 1 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
 				pinctrl-names = "default";
 				pinctrl-0 = <&qup_spi1_default>;
 				interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
@@ -988,6 +1021,9 @@
 				reg = <0 0x00888000 0 0x4000>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
+				dmas = <&gpi_dma0 0 2 QCOM_GPI_I2C>,
+				       <&gpi_dma0 1 2 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
 				pinctrl-names = "default";
 				pinctrl-0 = <&qup_i2c2_default>;
 				interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>;
@@ -1002,6 +1038,9 @@
 				reg-names = "se";
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
+				dmas = <&gpi_dma0 0 2 QCOM_GPI_SPI>,
+				       <&gpi_dma0 1 2 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
 				pinctrl-names = "default";
 				pinctrl-0 = <&qup_spi2_default>;
 				interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>;
@@ -1016,6 +1055,9 @@
 				reg = <0 0x0088c000 0 0x4000>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
+				dmas = <&gpi_dma0 0 3 QCOM_GPI_I2C>,
+				       <&gpi_dma0 1 3 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
 				pinctrl-names = "default";
 				pinctrl-0 = <&qup_i2c3_default>;
 				interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
@@ -1030,6 +1072,9 @@
 				reg-names = "se";
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
+				dmas = <&gpi_dma0 0 3 QCOM_GPI_SPI>,
+				       <&gpi_dma0 1 3 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
 				pinctrl-names = "default";
 				pinctrl-0 = <&qup_spi3_default>;
 				interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
@@ -1044,6 +1089,9 @@
 				reg = <0 0x00890000 0 0x4000>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
+				dmas = <&gpi_dma0 0 4 QCOM_GPI_I2C>,
+				       <&gpi_dma0 1 4 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
 				pinctrl-names = "default";
 				pinctrl-0 = <&qup_i2c4_default>;
 				interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>;
@@ -1058,6 +1106,9 @@
 				reg-names = "se";
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
+				dmas = <&gpi_dma0 0 4 QCOM_GPI_SPI>,
+				       <&gpi_dma0 1 4 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
 				pinctrl-names = "default";
 				pinctrl-0 = <&qup_spi4_default>;
 				interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>;
@@ -1072,6 +1123,9 @@
 				reg = <0 0x00894000 0 0x4000>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
+				dmas = <&gpi_dma0 0 5 QCOM_GPI_I2C>,
+				       <&gpi_dma0 1 5 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
 				pinctrl-names = "default";
 				pinctrl-0 = <&qup_i2c5_default>;
 				interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
@@ -1086,6 +1140,9 @@
 				reg-names = "se";
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
+				dmas = <&gpi_dma0 0 5 QCOM_GPI_SPI>,
+				       <&gpi_dma0 1 5 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
 				pinctrl-names = "default";
 				pinctrl-0 = <&qup_spi5_default>;
 				interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
@@ -1100,6 +1157,9 @@
 				reg = <0 0x00898000 0 0x4000>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>;
+				dmas = <&gpi_dma0 0 6 QCOM_GPI_I2C>,
+				       <&gpi_dma0 1 6 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
 				pinctrl-names = "default";
 				pinctrl-0 = <&qup_i2c6_default>;
 				interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>;
@@ -1114,6 +1174,9 @@
 				reg-names = "se";
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>;
+				dmas = <&gpi_dma0 0 6 QCOM_GPI_SPI>,
+				       <&gpi_dma0 1 6 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
 				pinctrl-names = "default";
 				pinctrl-0 = <&qup_spi6_default>;
 				interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>;
@@ -1128,6 +1191,9 @@
 				reg = <0 0x0089c000 0 0x4000>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>;
+				dmas = <&gpi_dma0 0 7 QCOM_GPI_I2C>,
+				       <&gpi_dma0 1 7 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
 				pinctrl-names = "default";
 				pinctrl-0 = <&qup_i2c7_default>;
 				interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>;
@@ -1142,6 +1208,9 @@
 				reg-names = "se";
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>;
+				dmas = <&gpi_dma0 0 7 QCOM_GPI_SPI>,
+				       <&gpi_dma0 1 7 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
 				pinctrl-names = "default";
 				pinctrl-0 = <&qup_spi7_default>;
 				interrupts = <GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>;
@@ -1192,6 +1261,9 @@
 				reg = <0 0x00a80000 0 0x4000>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
+				dmas = <&gpi_dma1 0 0 QCOM_GPI_I2C>,
+				       <&gpi_dma1 1 0 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
 				pinctrl-names = "default";
 				pinctrl-0 = <&qup_i2c8_default>;
 				interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
@@ -1206,6 +1278,9 @@
 				reg-names = "se";
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
+				dmas = <&gpi_dma1 0 0 QCOM_GPI_SPI>,
+				       <&gpi_dma1 1 0 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
 				pinctrl-names = "default";
 				pinctrl-0 = <&qup_spi8_default>;
 				interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
@@ -1220,6 +1295,9 @@
 				reg = <0 0x00a84000 0 0x4000>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
+				dmas = <&gpi_dma1 0 1 QCOM_GPI_I2C>,
+				       <&gpi_dma1 1 1 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
 				pinctrl-names = "default";
 				pinctrl-0 = <&qup_i2c9_default>;
 				interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
@@ -1234,6 +1312,9 @@
 				reg-names = "se";
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
+				dmas = <&gpi_dma1 0 1 QCOM_GPI_SPI>,
+				       <&gpi_dma1 1 1 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
 				pinctrl-names = "default";
 				pinctrl-0 = <&qup_spi9_default>;
 				interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
@@ -1248,6 +1329,9 @@
 				reg = <0 0x00a88000 0 0x4000>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
+				dmas = <&gpi_dma1 0 2 QCOM_GPI_I2C>,
+				       <&gpi_dma1 1 2 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
 				pinctrl-names = "default";
 				pinctrl-0 = <&qup_i2c10_default>;
 				interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
@@ -1262,6 +1346,9 @@
 				reg-names = "se";
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
+				dmas = <&gpi_dma1 0 2 QCOM_GPI_SPI>,
+				       <&gpi_dma1 1 2 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
 				pinctrl-names = "default";
 				pinctrl-0 = <&qup_spi10_default>;
 				interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
@@ -1276,6 +1363,9 @@
 				reg = <0 0x00a8c000 0 0x4000>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
+				dmas = <&gpi_dma1 0 3 QCOM_GPI_I2C>,
+				       <&gpi_dma1 1 3 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
 				pinctrl-names = "default";
 				pinctrl-0 = <&qup_i2c11_default>;
 				interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
@@ -1290,6 +1380,9 @@
 				reg-names = "se";
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
+				dmas = <&gpi_dma1 0 3 QCOM_GPI_SPI>,
+				       <&gpi_dma1 1 3 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
 				pinctrl-names = "default";
 				pinctrl-0 = <&qup_spi11_default>;
 				interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
@@ -1313,6 +1406,9 @@
 				reg = <0 0x00a90000 0 0x4000>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
+				dmas = <&gpi_dma1 0 4 QCOM_GPI_I2C>,
+				       <&gpi_dma1 1 4 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
 				pinctrl-names = "default";
 				pinctrl-0 = <&qup_i2c12_default>;
 				interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
@@ -1327,6 +1423,9 @@
 				reg-names = "se";
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
+				dmas = <&gpi_dma1 0 4 QCOM_GPI_SPI>,
+				       <&gpi_dma1 1 4 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
 				pinctrl-names = "default";
 				pinctrl-0 = <&qup_spi12_default>;
 				interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
@@ -1341,6 +1440,9 @@
 				reg = <0 0x0094000 0 0x4000>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
+				dmas = <&gpi_dma2 0 5 QCOM_GPI_I2C>,
+				       <&gpi_dma2 1 5 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
 				pinctrl-names = "default";
 				pinctrl-0 = <&qup_i2c16_default>;
 				interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
@@ -1355,6 +1457,9 @@
 				reg-names = "se";
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
+				dmas = <&gpi_dma2 0 5 QCOM_GPI_SPI>,
+				       <&gpi_dma2 1 5 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
 				pinctrl-names = "default";
 				pinctrl-0 = <&qup_spi16_default>;
 				interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
@@ -1406,6 +1511,9 @@
 				reg = <0 0x00c80000 0 0x4000>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP2_S0_CLK>;
+				dmas = <&gpi_dma2 0 0 QCOM_GPI_I2C>,
+				       <&gpi_dma2 1 0 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
 				pinctrl-names = "default";
 				pinctrl-0 = <&qup_i2c17_default>;
 				interrupts = <GIC_SPI 373 IRQ_TYPE_LEVEL_HIGH>;
@@ -1420,6 +1528,9 @@
 				reg-names = "se";
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP2_S0_CLK>;
+				dmas = <&gpi_dma2 0 0 QCOM_GPI_SPI>,
+				       <&gpi_dma2 1 0 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
 				pinctrl-names = "default";
 				pinctrl-0 = <&qup_spi17_default>;
 				interrupts = <GIC_SPI 373 IRQ_TYPE_LEVEL_HIGH>;
@@ -1434,6 +1545,9 @@
 				reg = <0 0x00c84000 0 0x4000>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP2_S1_CLK>;
+				dmas = <&gpi_dma2 0 1 QCOM_GPI_I2C>,
+				       <&gpi_dma2 1 1 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
 				pinctrl-names = "default";
 				pinctrl-0 = <&qup_i2c18_default>;
 				interrupts = <GIC_SPI 583 IRQ_TYPE_LEVEL_HIGH>;
@@ -1448,6 +1562,9 @@
 				reg-names = "se";
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP2_S1_CLK>;
+				dmas = <&gpi_dma2 0 1 QCOM_GPI_SPI>,
+				       <&gpi_dma2 1 1 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
 				pinctrl-names = "default";
 				pinctrl-0 = <&qup_spi18_default>;
 				interrupts = <GIC_SPI 583 IRQ_TYPE_LEVEL_HIGH>;
@@ -1462,6 +1579,9 @@
 				reg = <0 0x00c88000 0 0x4000>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP2_S2_CLK>;
+				dmas = <&gpi_dma2 0 2 QCOM_GPI_I2C>,
+				       <&gpi_dma2 1 2 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
 				pinctrl-names = "default";
 				pinctrl-0 = <&qup_i2c19_default>;
 				interrupts = <GIC_SPI 584 IRQ_TYPE_LEVEL_HIGH>;
@@ -1476,6 +1596,9 @@
 				reg-names = "se";
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP2_S2_CLK>;
+				dmas = <&gpi_dma2 0 2 QCOM_GPI_SPI>,
+				       <&gpi_dma2 1 2 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
 				pinctrl-names = "default";
 				pinctrl-0 = <&qup_spi19_default>;
 				interrupts = <GIC_SPI 584 IRQ_TYPE_LEVEL_HIGH>;
@@ -1490,6 +1613,9 @@
 				reg = <0 0x00c8c000 0 0x4000>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP2_S3_CLK>;
+				dmas = <&gpi_dma2 0 3 QCOM_GPI_I2C>,
+				       <&gpi_dma2 1 3 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
 				pinctrl-names = "default";
 				pinctrl-0 = <&qup_i2c13_default>;
 				interrupts = <GIC_SPI 585 IRQ_TYPE_LEVEL_HIGH>;
@@ -1504,6 +1630,9 @@
 				reg-names = "se";
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP2_S3_CLK>;
+				dmas = <&gpi_dma2 0 3 QCOM_GPI_SPI>,
+				       <&gpi_dma2 1 3 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
 				pinctrl-names = "default";
 				pinctrl-0 = <&qup_spi13_default>;
 				interrupts = <GIC_SPI 585 IRQ_TYPE_LEVEL_HIGH>;
@@ -1518,6 +1647,9 @@
 				reg = <0 0x00c90000 0 0x4000>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP2_S4_CLK>;
+				dmas = <&gpi_dma2 0 4 QCOM_GPI_I2C>,
+				       <&gpi_dma2 1 4 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
 				pinctrl-names = "default";
 				pinctrl-0 = <&qup_i2c14_default>;
 				interrupts = <GIC_SPI 586 IRQ_TYPE_LEVEL_HIGH>;
@@ -1532,6 +1664,9 @@
 				reg-names = "se";
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP2_S4_CLK>;
+				dmas = <&gpi_dma2 0 4 QCOM_GPI_SPI>,
+				       <&gpi_dma2 1 4 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
 				pinctrl-names = "default";
 				pinctrl-0 = <&qup_spi14_default>;
 				interrupts = <GIC_SPI 586 IRQ_TYPE_LEVEL_HIGH>;
@@ -1546,6 +1681,9 @@
 				reg = <0 0x00c94000 0 0x4000>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP2_S5_CLK>;
+				dmas = <&gpi_dma2 0 5 QCOM_GPI_I2C>,
+				       <&gpi_dma2 1 5 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
 				pinctrl-names = "default";
 				pinctrl-0 = <&qup_i2c15_default>;
 				interrupts = <GIC_SPI 587 IRQ_TYPE_LEVEL_HIGH>;
@@ -1560,6 +1698,9 @@
 				reg-names = "se";
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP2_S5_CLK>;
+				dmas = <&gpi_dma2 0 5 QCOM_GPI_SPI>,
+				       <&gpi_dma2 1 5 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
 				pinctrl-names = "default";
 				pinctrl-0 = <&qup_spi15_default>;
 				interrupts = <GIC_SPI 587 IRQ_TYPE_LEVEL_HIGH>;
@@ -1626,6 +1767,203 @@
 			interrupts = <GIC_SPI 582 IRQ_TYPE_LEVEL_HIGH>;
 		};
 
+		pcie0: pci@1c00000 {
+			compatible = "qcom,pcie-sm8150", "snps,dw-pcie";
+			reg = <0 0x01c00000 0 0x3000>,
+			      <0 0x60000000 0 0xf1d>,
+			      <0 0x60000f20 0 0xa8>,
+			      <0 0x60001000 0 0x1000>,
+			      <0 0x60100000 0 0x100000>;
+			reg-names = "parf", "dbi", "elbi", "atu", "config";
+			device_type = "pci";
+			linux,pci-domain = <0>;
+			bus-range = <0x00 0xff>;
+			num-lanes = <1>;
+
+			#address-cells = <3>;
+			#size-cells = <2>;
+
+			ranges = <0x01000000 0x0 0x60200000 0 0x60200000 0x0 0x100000>,
+				 <0x02000000 0x0 0x60300000 0 0x60300000 0x0 0x3d00000>;
+
+			interrupts = <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "msi";
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0x7>;
+			interrupt-map = <0 0 0 1 &intc 0 149 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+					<0 0 0 2 &intc 0 150 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+					<0 0 0 3 &intc 0 151 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+					<0 0 0 4 &intc 0 152 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+
+			clocks = <&gcc GCC_PCIE_0_PIPE_CLK>,
+				 <&gcc GCC_PCIE_0_AUX_CLK>,
+				 <&gcc GCC_PCIE_0_CFG_AHB_CLK>,
+				 <&gcc GCC_PCIE_0_MSTR_AXI_CLK>,
+				 <&gcc GCC_PCIE_0_SLV_AXI_CLK>,
+				 <&gcc GCC_PCIE_0_SLV_Q2A_AXI_CLK>,
+				 <&gcc GCC_AGGRE_NOC_PCIE_TBU_CLK>;
+			clock-names = "pipe",
+				      "aux",
+				      "cfg",
+				      "bus_master",
+				      "bus_slave",
+				      "slave_q2a",
+				      "tbu";
+
+			iommus = <&apps_smmu 0x1d80 0x7f>;
+			iommu-map = <0x0   &apps_smmu 0x1d80 0x1>,
+				    <0x100 &apps_smmu 0x1d81 0x1>;
+
+			resets = <&gcc GCC_PCIE_0_BCR>;
+			reset-names = "pci";
+
+			power-domains = <&gcc PCIE_0_GDSC>;
+
+			phys = <&pcie0_lane>;
+			phy-names = "pciephy";
+
+			perst-gpio = <&tlmm 35 GPIO_ACTIVE_HIGH>;
+			enable-gpio = <&tlmm 37 GPIO_ACTIVE_HIGH>;
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&pcie0_default_state>;
+
+			status = "disabled";
+		};
+
+		pcie0_phy: phy@1c06000 {
+			compatible = "qcom,sm8150-qmp-gen3x1-pcie-phy";
+			reg = <0 0x01c06000 0 0x1c0>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+			clocks = <&gcc GCC_PCIE_PHY_AUX_CLK>,
+				 <&gcc GCC_PCIE_0_CFG_AHB_CLK>,
+				 <&gcc GCC_PCIE0_PHY_REFGEN_CLK>;
+			clock-names = "aux", "cfg_ahb", "refgen";
+
+			resets = <&gcc GCC_PCIE_0_PHY_BCR>;
+			reset-names = "phy";
+
+			assigned-clocks = <&gcc GCC_PCIE0_PHY_REFGEN_CLK>;
+			assigned-clock-rates = <100000000>;
+
+			status = "disabled";
+
+			pcie0_lane: phy@1c06200 {
+				reg = <0 0x1c06200 0 0x170>, /* tx */
+				      <0 0x1c06400 0 0x200>, /* rx */
+				      <0 0x1c06800 0 0x1f0>, /* pcs */
+				      <0 0x1c06c00 0 0xf4>; /* "pcs_lane" same as pcs_misc? */
+				clocks = <&gcc GCC_PCIE_0_PIPE_CLK>;
+				clock-names = "pipe0";
+
+				#phy-cells = <0>;
+				clock-output-names = "pcie_0_pipe_clk";
+			};
+		};
+
+		pcie1: pci@1c08000 {
+			compatible = "qcom,pcie-sm8150", "snps,dw-pcie";
+			reg = <0 0x01c08000 0 0x3000>,
+			      <0 0x40000000 0 0xf1d>,
+			      <0 0x40000f20 0 0xa8>,
+			      <0 0x40001000 0 0x1000>,
+			      <0 0x40100000 0 0x100000>;
+			reg-names = "parf", "dbi", "elbi", "atu", "config";
+			device_type = "pci";
+			linux,pci-domain = <1>;
+			bus-range = <0x00 0xff>;
+			num-lanes = <2>;
+
+			#address-cells = <3>;
+			#size-cells = <2>;
+
+			ranges = <0x01000000 0x0 0x40200000 0x0 0x40200000 0x0 0x100000>,
+				 <0x02000000 0x0 0x40300000 0x0 0x40300000 0x0 0x1fd00000>;
+
+			interrupts = <GIC_SPI 307 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "msi";
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0x7>;
+			interrupt-map = <0 0 0 1 &intc 0 434 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+					<0 0 0 2 &intc 0 435 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+					<0 0 0 3 &intc 0 438 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+					<0 0 0 4 &intc 0 439 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+
+			clocks = <&gcc GCC_PCIE_1_PIPE_CLK>,
+				 <&gcc GCC_PCIE_1_AUX_CLK>,
+				 <&gcc GCC_PCIE_1_CFG_AHB_CLK>,
+				 <&gcc GCC_PCIE_1_MSTR_AXI_CLK>,
+				 <&gcc GCC_PCIE_1_SLV_AXI_CLK>,
+				 <&gcc GCC_PCIE_1_SLV_Q2A_AXI_CLK>,
+				 <&gcc GCC_AGGRE_NOC_PCIE_TBU_CLK>;
+			clock-names = "pipe",
+				      "aux",
+				      "cfg",
+				      "bus_master",
+				      "bus_slave",
+				      "slave_q2a",
+				      "tbu";
+
+			assigned-clocks = <&gcc GCC_PCIE_1_AUX_CLK>;
+			assigned-clock-rates = <19200000>;
+
+			iommus = <&apps_smmu 0x1e00 0x7f>;
+			iommu-map = <0x0   &apps_smmu 0x1e00 0x1>,
+				    <0x100 &apps_smmu 0x1e01 0x1>;
+
+			resets = <&gcc GCC_PCIE_1_BCR>;
+			reset-names = "pci";
+
+			power-domains = <&gcc PCIE_1_GDSC>;
+
+			phys = <&pcie1_lane>;
+			phy-names = "pciephy";
+
+			perst-gpio = <&tlmm 102 GPIO_ACTIVE_HIGH>;
+			enable-gpio = <&tlmm 104 GPIO_ACTIVE_HIGH>;
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&pcie1_default_state>;
+
+			status = "disabled";
+		};
+
+		pcie1_phy: phy@1c0e000 {
+			compatible = "qcom,sm8150-qmp-gen3x2-pcie-phy";
+			reg = <0 0x01c0e000 0 0x1c0>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+			clocks = <&gcc GCC_PCIE_PHY_AUX_CLK>,
+				 <&gcc GCC_PCIE_1_CFG_AHB_CLK>,
+				 <&gcc GCC_PCIE1_PHY_REFGEN_CLK>;
+			clock-names = "aux", "cfg_ahb", "refgen";
+
+			resets = <&gcc GCC_PCIE_1_PHY_BCR>;
+			reset-names = "phy";
+
+			assigned-clocks = <&gcc GCC_PCIE1_PHY_REFGEN_CLK>;
+			assigned-clock-rates = <100000000>;
+
+			status = "disabled";
+
+			pcie1_lane: phy@1c0e200 {
+				reg = <0 0x1c0e200 0 0x170>, /* tx0 */
+				      <0 0x1c0e400 0 0x200>, /* rx0 */
+				      <0 0x1c0ea00 0 0x1f0>, /* pcs */
+				      <0 0x1c0e600 0 0x170>, /* tx1 */
+				      <0 0x1c0e800 0 0x200>, /* rx1 */
+				      <0 0x1c0ee00 0 0xf4>; /* "pcs_com" same as pcs_misc? */
+				clocks = <&gcc GCC_PCIE_1_PIPE_CLK>;
+				clock-names = "pipe0";
+
+				#phy-cells = <0>;
+				clock-output-names = "pcie_1_pipe_clk";
+			};
+		};
+
 		ufs_mem_hc: ufshc@1d84000 {
 			compatible = "qcom,sm8150-ufshc", "qcom,ufshc",
 				     "jedec,ufs-2.0";
@@ -1687,6 +2025,8 @@
 			clocks = <&gcc GCC_UFS_MEM_CLKREF_CLK>,
 				 <&gcc GCC_UFS_PHY_PHY_AUX_CLK>;
 
+			power-domains = <&gcc UFS_PHY_GDSC>;
+
 			resets = <&ufs_mem_hc 0>;
 			reset-names = "ufsphy";
 			status = "disabled";
@@ -1708,9 +2048,15 @@
 			qcom,bcm-voters = <&apps_bcm_voter>;
 		};
 
-		tcsr_mutex_regs: syscon@1f40000 {
-			compatible = "syscon";
-			reg = <0x0 0x01f40000 0x0 0x40000>;
+		tcsr_mutex: hwlock@1f40000 {
+			compatible = "qcom,tcsr-mutex";
+			reg = <0x0 0x01f40000 0x0 0x20000>;
+			#hwlock-cells = <1>;
+		};
+
+		tcsr_regs_1: syscon@1f60000 {
+			compatible = "qcom,sm8150-tcsr", "syscon";
+			reg = <0x0 0x01f60000 0x0 0x20000>;
 		};
 
 		remoteproc_slpi: remoteproc@2400000 {
@@ -1751,6 +2097,7 @@
 					compatible = "qcom,fastrpc";
 					qcom,glink-channels = "fastrpcglink-apps-dsp";
 					label = "sdsp";
+					qcom,non-secure-domain;
 					#address-cells = <1>;
 					#size-cells = <0>;
 
@@ -1785,7 +2132,6 @@
 			compatible = "qcom,adreno-640.1",
 				     "qcom,adreno",
 				     "amd,imageon";
-			#stream-id-cells = <16>;
 
 			reg = <0 0x02c00000 0 0x40000>;
 			reg-names = "kgsl_3d0_reg_memory";
@@ -1841,7 +2187,7 @@
 		};
 
 		gmu: gmu@2c6a000 {
-			compatible="qcom,adreno-gmu-640.1", "qcom,adreno-gmu";
+			compatible = "qcom,adreno-gmu-640.1", "qcom,adreno-gmu";
 
 			reg = <0 0x02c6a000 0 0x30000>,
 			      <0 0x0b290000 0 0x10000>,
@@ -1928,6 +2274,7 @@
 			#gpio-cells = <2>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
+			wakeup-parent = <&pdc>;
 
 			qup_i2c0_default: qup-i2c0-default {
 				mux {
@@ -2328,6 +2675,52 @@
 				drive-strength = <6>;
 				bias-disable;
 			};
+
+			pcie0_default_state: pcie0-default {
+				perst {
+					pins = "gpio35";
+					function = "gpio";
+					drive-strength = <2>;
+					bias-pull-down;
+				};
+
+				clkreq {
+					pins = "gpio36";
+					function = "pci_e0";
+					drive-strength = <2>;
+					bias-pull-up;
+				};
+
+				wake {
+					pins = "gpio37";
+					function = "gpio";
+					drive-strength = <2>;
+					bias-pull-up;
+				};
+			};
+
+			pcie1_default_state: pcie1-default {
+				perst {
+					pins = "gpio102";
+					function = "gpio";
+					drive-strength = <2>;
+					bias-pull-down;
+				};
+
+				clkreq {
+					pins = "gpio103";
+					function = "pci_e1";
+					drive-strength = <2>;
+					bias-pull-up;
+				};
+
+				wake {
+					pins = "gpio104";
+					function = "gpio";
+					drive-strength = <2>;
+					bias-pull-up;
+				};
+			};
 		};
 
 		remoteproc_mpss: remoteproc@4080000 {
@@ -2994,63 +3387,56 @@
 					compatible = "qcom,fastrpc";
 					qcom,glink-channels = "fastrpcglink-apps-dsp";
 					label = "cdsp";
+					qcom,non-secure-domain;
 					#address-cells = <1>;
 					#size-cells = <0>;
 
 					compute-cb@1 {
 						compatible = "qcom,fastrpc-compute-cb";
 						reg = <1>;
-						iommus = <&apps_smmu 0x1401 0x2040>,
-							 <&apps_smmu 0x1421 0x0>,
-							 <&apps_smmu 0x2001 0x420>,
-							 <&apps_smmu 0x2041 0x0>;
+						iommus = <&apps_smmu 0x1001 0x0460>;
 					};
 
 					compute-cb@2 {
 						compatible = "qcom,fastrpc-compute-cb";
 						reg = <2>;
-						iommus = <&apps_smmu 0x2 0x3440>,
-							 <&apps_smmu 0x22 0x3400>;
+						iommus = <&apps_smmu 0x1002 0x0460>;
 					};
 
 					compute-cb@3 {
 						compatible = "qcom,fastrpc-compute-cb";
 						reg = <3>;
-						iommus = <&apps_smmu 0x3 0x3440>,
-							 <&apps_smmu 0x1423 0x0>,
-							 <&apps_smmu 0x2023 0x0>;
+						iommus = <&apps_smmu 0x1003 0x0460>;
 					};
 
 					compute-cb@4 {
 						compatible = "qcom,fastrpc-compute-cb";
 						reg = <4>;
-						iommus = <&apps_smmu 0x4 0x3440>,
-							 <&apps_smmu 0x24 0x3400>;
+						iommus = <&apps_smmu 0x1004 0x0460>;
 					};
 
 					compute-cb@5 {
 						compatible = "qcom,fastrpc-compute-cb";
 						reg = <5>;
-						iommus = <&apps_smmu 0x5 0x3440>,
-							 <&apps_smmu 0x25 0x3400>;
+						iommus = <&apps_smmu 0x1005 0x0460>;
 					};
 
 					compute-cb@6 {
 						compatible = "qcom,fastrpc-compute-cb";
 						reg = <6>;
-						iommus = <&apps_smmu 0x6 0x3460>;
+						iommus = <&apps_smmu 0x1006 0x0460>;
 					};
 
 					compute-cb@7 {
 						compatible = "qcom,fastrpc-compute-cb";
 						reg = <7>;
-						iommus = <&apps_smmu 0x7 0x3460>;
+						iommus = <&apps_smmu 0x1007 0x0460>;
 					};
 
 					compute-cb@8 {
 						compatible = "qcom,fastrpc-compute-cb";
 						reg = <8>;
-						iommus = <&apps_smmu 0x8 0x3460>;
+						iommus = <&apps_smmu 0x1008 0x0460>;
 					};
 
 					/* note: secure cb9 in downstream */
@@ -3149,6 +3535,51 @@
 			};
 		};
 
+		sdhc_2: mmc@8804000 {
+			compatible = "qcom,sm8150-sdhci", "qcom,sdhci-msm-v5";
+			reg = <0 0x08804000 0 0x1000>;
+
+			interrupts = <GIC_SPI 204 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 222 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hc_irq", "pwr_irq";
+
+			clocks = <&gcc GCC_SDCC2_AHB_CLK>,
+				 <&gcc GCC_SDCC2_APPS_CLK>,
+				 <&rpmhcc RPMH_CXO_CLK>;
+			clock-names = "iface", "core", "xo";
+			iommus = <&apps_smmu 0x6a0 0x0>;
+			qcom,dll-config = <0x0007642c>;
+			qcom,ddr-config = <0x80040868>;
+			power-domains = <&rpmhpd 0>;
+			operating-points-v2 = <&sdhc2_opp_table>;
+
+			status = "disabled";
+
+			sdhc2_opp_table: opp-table {
+				compatible = "operating-points-v2";
+
+				opp-19200000 {
+					opp-hz = /bits/ 64 <19200000>;
+					required-opps = <&rpmhpd_opp_min_svs>;
+				};
+
+				opp-50000000 {
+					opp-hz = /bits/ 64 <50000000>;
+					required-opps = <&rpmhpd_opp_low_svs>;
+				};
+
+				opp-100000000 {
+					opp-hz = /bits/ 64 <100000000>;
+					required-opps = <&rpmhpd_opp_svs>;
+				};
+
+				opp-202000000 {
+					opp-hz = /bits/ 64 <202000000>;
+					required-opps = <&rpmhpd_opp_svs_l1>;
+				};
+			};
+		};
+
 		dc_noc: interconnect@9160000 {
 			compatible = "qcom,sm8150-dc-noc";
 			reg = <0 0x09160000 0 0x3200>;
@@ -3175,11 +3606,15 @@
 			clocks = <&gcc GCC_CFG_NOC_USB3_PRIM_AXI_CLK>,
 				 <&gcc GCC_USB30_PRIM_MASTER_CLK>,
 				 <&gcc GCC_AGGRE_USB3_PRIM_AXI_CLK>,
-				 <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
 				 <&gcc GCC_USB30_PRIM_SLEEP_CLK>,
+				 <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
 				 <&gcc GCC_USB3_SEC_CLKREF_CLK>;
-			clock-names = "cfg_noc", "core", "iface", "mock_utmi",
-				      "sleep", "xo";
+			clock-names = "cfg_noc",
+				      "core",
+				      "iface",
+				      "sleep",
+				      "mock_utmi",
+				      "xo";
 
 			assigned-clocks = <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
 					  <&gcc GCC_USB30_PRIM_MASTER_CLK>;
@@ -3196,7 +3631,7 @@
 
 			resets = <&gcc GCC_USB30_PRIM_BCR>;
 
-			usb_1_dwc3: dwc3@a600000 {
+			usb_1_dwc3: usb@a600000 {
 				compatible = "snps,dwc3";
 				reg = <0 0x0a600000 0 0xcd00>;
 				interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
@@ -3220,11 +3655,15 @@
 			clocks = <&gcc GCC_CFG_NOC_USB3_SEC_AXI_CLK>,
 				 <&gcc GCC_USB30_SEC_MASTER_CLK>,
 				 <&gcc GCC_AGGRE_USB3_SEC_AXI_CLK>,
-				 <&gcc GCC_USB30_SEC_MOCK_UTMI_CLK>,
 				 <&gcc GCC_USB30_SEC_SLEEP_CLK>,
+				 <&gcc GCC_USB30_SEC_MOCK_UTMI_CLK>,
 				 <&gcc GCC_USB3_SEC_CLKREF_CLK>;
-			clock-names = "cfg_noc", "core", "iface", "mock_utmi",
-				      "sleep", "xo";
+			clock-names = "cfg_noc",
+				      "core",
+				      "iface",
+				      "sleep",
+				      "mock_utmi",
+				      "xo";
 
 			assigned-clocks = <&gcc GCC_USB30_SEC_MOCK_UTMI_CLK>,
 					  <&gcc GCC_USB30_SEC_MASTER_CLK>;
@@ -3260,8 +3699,18 @@
 			qcom,bcm-voters = <&apps_bcm_voter>;
 		};
 
+		pdc: interrupt-controller@b220000 {
+			compatible = "qcom,sm8150-pdc", "qcom,pdc";
+			reg = <0 0x0b220000 0 0x400>;
+			qcom,pdc-ranges = <0 480 94>, <94 609 31>,
+					  <125 63 1>;
+			#interrupt-cells = <2>;
+			interrupt-parent = <&intc>;
+			interrupt-controller;
+		};
+
 		aoss_qmp: power-controller@c300000 {
-			compatible = "qcom,sm8150-aoss-qmp";
+			compatible = "qcom,sm8150-aoss-qmp", "qcom,aoss-qmp";
 			reg = <0x0 0x0c300000 0x0 0x400>;
 			interrupts = <GIC_SPI 389 IRQ_TYPE_EDGE_RISING>;
 			mboxes = <&apss_shared 0>;
@@ -3439,6 +3888,7 @@
 					compatible = "qcom,fastrpc";
 					qcom,glink-channels = "fastrpcglink-apps-dsp";
 					label = "adsp";
+					qcom,non-secure-domain;
 					#address-cells = <1>;
 					#size-cells = <0>;
 
@@ -3486,9 +3936,9 @@
 		};
 
 		timer@17c20000 {
-			#address-cells = <2>;
-			#size-cells = <2>;
-			ranges;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0 0 0x20000000>;
 			compatible = "arm,armv7-timer-mem";
 			reg = <0x0 0x17c20000 0x0 0x1000>;
 			clock-frequency = <19200000>;
@@ -3497,49 +3947,49 @@
 				frame-number = <0>;
 				interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
 					     <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0x0 0x17c21000 0x0 0x1000>,
-				      <0x0 0x17c22000 0x0 0x1000>;
+				reg = <0x17c21000 0x1000>,
+				      <0x17c22000 0x1000>;
 			};
 
 			frame@17c23000 {
 				frame-number = <1>;
 				interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0x0 0x17c23000 0x0 0x1000>;
+				reg = <0x17c23000 0x1000>;
 				status = "disabled";
 			};
 
 			frame@17c25000 {
 				frame-number = <2>;
 				interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0x0 0x17c25000 0x0 0x1000>;
+				reg = <0x17c25000 0x1000>;
 				status = "disabled";
 			};
 
 			frame@17c27000 {
 				frame-number = <3>;
 				interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0x0 0x17c26000 0x0 0x1000>;
+				reg = <0x17c26000 0x1000>;
 				status = "disabled";
 			};
 
 			frame@17c29000 {
 				frame-number = <4>;
 				interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0x0 0x17c29000 0x0 0x1000>;
+				reg = <0x17c29000 0x1000>;
 				status = "disabled";
 			};
 
 			frame@17c2b000 {
 				frame-number = <5>;
 				interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0x0 0x17c2b000 0x0 0x1000>;
+				reg = <0x17c2b000 0x1000>;
 				status = "disabled";
 			};
 
 			frame@17c2d000 {
 				frame-number = <6>;
 				interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0x0 0x17c2d000 0x0 0x1000>;
+				reg = <0x17c2d000 0x1000>;
 				status = "disabled";
 			};
 		};
@@ -3557,9 +4007,9 @@
 			qcom,tcs-offset = <0xd00>;
 			qcom,drv-id = <2>;
 			qcom,tcs-config = <ACTIVE_TCS  2>,
-					  <SLEEP_TCS   1>,
-					  <WAKE_TCS    1>,
-					  <CONTROL_TCS 0>;
+					  <SLEEP_TCS   3>,
+					  <WAKE_TCS    3>,
+					  <CONTROL_TCS 1>;
 
 			rpmhcc: clock-controller {
 				compatible = "qcom,sm8150-rpmh-clk";
@@ -3622,7 +4072,7 @@
 				};
 			};
 
-			apps_bcm_voter: bcm_voter {
+			apps_bcm_voter: bcm-voter {
 				compatible = "qcom,bcm-voter";
 			};
 		};
@@ -3650,6 +4100,30 @@
 			#freq-domain-cells = <1>;
 		};
 
+		lmh_cluster1: lmh@18350800 {
+			compatible = "qcom,sm8150-lmh";
+			reg = <0 0x18350800 0 0x400>;
+			interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+			cpus = <&CPU4>;
+			qcom,lmh-temp-arm-millicelsius = <60000>;
+			qcom,lmh-temp-low-millicelsius = <84500>;
+			qcom,lmh-temp-high-millicelsius = <85000>;
+			interrupt-controller;
+			#interrupt-cells = <1>;
+		};
+
+		lmh_cluster0: lmh@18358800 {
+			compatible = "qcom,sm8150-lmh";
+			reg = <0 0x18358800 0 0x400>;
+			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+			cpus = <&CPU0>;
+			qcom,lmh-temp-arm-millicelsius = <60000>;
+			qcom,lmh-temp-low-millicelsius = <84500>;
+			qcom,lmh-temp-high-millicelsius = <85000>;
+			interrupt-controller;
+			#interrupt-cells = <1>;
+		};
+
 		wifi: wifi@18800000 {
 			compatible = "qcom,wcn3990-wifi";
 			reg = <0 0x18800000 0 0x800000>;
@@ -4266,7 +4740,7 @@
 			};
 		};
 
-		gpu-thermal-top {
+		gpu-top-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 
@@ -4446,7 +4920,7 @@
 			};
 		};
 
-		gpu-thermal-bottom {
+		gpu-bottom-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 
diff --git a/arch/arm64/boot/dts/qcom/sm8250-hdk.dts b/arch/arm64/boot/dts/qcom/sm8250-hdk.dts
index 3b082472062b..632e98193d27 100644
--- a/arch/arm64/boot/dts/qcom/sm8250-hdk.dts
+++ b/arch/arm64/boot/dts/qcom/sm8250-hdk.dts
@@ -53,10 +53,10 @@
 		vin-supply = <&vph_pwr>;
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
 
-		vol-up {
+		key-vol-up {
 			label = "Volume Up";
 			linux,code = <KEY_VOLUMEUP>;
 			gpios = <&pm8150_gpios 6 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm64/boot/dts/qcom/sm8250-mtp.dts b/arch/arm64/boot/dts/qcom/sm8250-mtp.dts
index 5ffbcdd387ba..a102aa5efa32 100644
--- a/arch/arm64/boot/dts/qcom/sm8250-mtp.dts
+++ b/arch/arm64/boot/dts/qcom/sm8250-mtp.dts
@@ -6,6 +6,9 @@
 /dts-v1/;
 
 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+#include <dt-bindings/sound/qcom,q6afe.h>
+#include <dt-bindings/sound/qcom,q6asm.h>
+#include <dt-bindings/gpio/gpio.h>
 #include "sm8250.dtsi"
 #include "pm8150.dtsi"
 #include "pm8150b.dtsi"
@@ -619,13 +622,213 @@
 	status = "okay";
 };
 
+&rxmacro {
+	status = "okay";
+};
+
 &slpi {
 	status = "okay";
 	firmware-name = "qcom/sm8250/slpi.mbn";
 };
 
+&soc {
+	wcd938x: codec {
+		compatible = "qcom,wcd9380-codec";
+		#sound-dai-cells = <1>;
+		reset-gpios = <&tlmm 32 GPIO_ACTIVE_HIGH>;
+		vdd-buck-supply = <&vreg_s4a_1p8>;
+		vdd-rxtx-supply = <&vreg_s4a_1p8>;
+		vdd-io-supply = <&vreg_s4a_1p8>;
+		vdd-mic-bias-supply = <&vreg_bob>;
+		qcom,micbias1-microvolt = <1800000>;
+		qcom,micbias2-microvolt = <1800000>;
+		qcom,micbias3-microvolt = <1800000>;
+		qcom,micbias4-microvolt = <1800000>;
+		qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000 500000 500000 500000 500000>;
+		qcom,mbhc-headset-vthreshold-microvolt = <1700000>;
+		qcom,mbhc-headphone-vthreshold-microvolt = <50000>;
+		qcom,rx-device = <&wcd_rx>;
+		qcom,tx-device = <&wcd_tx>;
+	};
+};
+
+&sound {
+	compatible = "qcom,sm8250-sndcard";
+	model = "SM8250-MTP-WCD9380-WSA8810-VA-DMIC";
+	audio-routing =
+		"SpkrLeft IN", "WSA_SPK1 OUT",
+		"SpkrRight IN", "WSA_SPK2 OUT",
+		"IN1_HPHL", "HPHL_OUT",
+		"IN2_HPHR", "HPHR_OUT",
+		"AMIC1", "MIC BIAS1",
+		"AMIC2", "MIC BIAS2",
+		"AMIC3", "MIC BIAS3",
+		"AMIC4", "MIC BIAS3",
+		"AMIC5", "MIC BIAS4",
+		"TX SWR_ADC0", "ADC1_OUTPUT",
+		"TX SWR_ADC1", "ADC2_OUTPUT",
+		"TX SWR_ADC2", "ADC3_OUTPUT",
+		"TX SWR_ADC3", "ADC4_OUTPUT",
+		"TX SWR_DMIC0", "DMIC1_OUTPUT",
+		"TX SWR_DMIC1", "DMIC2_OUTPUT",
+		"TX SWR_DMIC2", "DMIC3_OUTPUT",
+		"TX SWR_DMIC3", "DMIC4_OUTPUT",
+		"TX SWR_DMIC4", "DMIC5_OUTPUT",
+		"TX SWR_DMIC5", "DMIC6_OUTPUT",
+		"TX SWR_DMIC6", "DMIC7_OUTPUT",
+		"TX SWR_DMIC7", "DMIC8_OUTPUT";
+
+	mm1-dai-link {
+		link-name = "MultiMedia1";
+		cpu {
+			sound-dai = <&q6asmdai  MSM_FRONTEND_DAI_MULTIMEDIA1>;
+		};
+	};
+
+	mm2-dai-link {
+		link-name = "MultiMedia2";
+		cpu {
+			sound-dai = <&q6asmdai  MSM_FRONTEND_DAI_MULTIMEDIA2>;
+		};
+	};
+
+	mm3-dai-link {
+		link-name = "MultiMedia3";
+		cpu {
+			sound-dai = <&q6asmdai  MSM_FRONTEND_DAI_MULTIMEDIA3>;
+		};
+	};
+
+	wcd-playback-dai-link {
+		link-name = "WCD Playback";
+		cpu {
+			sound-dai = <&q6afedai RX_CODEC_DMA_RX_0>;
+		};
+		codec {
+			sound-dai = <&wcd938x 0>, <&swr1 0>, <&rxmacro 0>;
+		};
+		platform {
+			sound-dai = <&q6routing>;
+		};
+	};
+
+	wcd-capture-dai-link {
+		link-name = "WCD Capture";
+		cpu {
+			sound-dai = <&q6afedai TX_CODEC_DMA_TX_3>;
+		};
+
+		codec {
+			sound-dai = <&wcd938x 1>, <&swr2 0>, <&txmacro 0>;
+		};
+		platform {
+			sound-dai = <&q6routing>;
+		};
+	};
+
+	wsa-dai-link {
+		link-name = "WSA Playback";
+		cpu {
+			sound-dai = <&q6afedai WSA_CODEC_DMA_RX_0>;
+		};
+
+		codec {
+			sound-dai = <&left_spkr>, <&right_spkr>, <&swr0 0>, <&wsamacro 0>;
+		};
+		platform {
+			sound-dai = <&q6routing>;
+		};
+	};
+
+	va-dai-link {
+		link-name = "VA Capture";
+		cpu {
+			sound-dai = <&q6afedai VA_CODEC_DMA_TX_0>;
+		};
+
+		platform {
+			sound-dai = <&q6routing>;
+		};
+
+		codec {
+			sound-dai = <&vamacro 0>;
+		};
+	};
+};
+
+&swr0 {
+	left_spkr: wsa8810-right@0,3{
+		compatible = "sdw10217211000";
+		reg = <0 3>;
+		powerdown-gpios = <&tlmm 26 GPIO_ACTIVE_HIGH>;
+		#thermal-sensor-cells = <0>;
+		sound-name-prefix = "SpkrLeft";
+		#sound-dai-cells = <0>;
+	};
+
+	right_spkr: wsa8810-left@0,4{
+		compatible = "sdw10217211000";
+		reg = <0 4>;
+		powerdown-gpios = <&tlmm 127 GPIO_ACTIVE_HIGH>;
+		#thermal-sensor-cells = <0>;
+		sound-name-prefix = "SpkrRight";
+		#sound-dai-cells = <0>;
+	};
+};
+
+&swr1 {
+	status = "okay";
+
+	wcd_rx: wcd9380-rx@0,4 {
+		compatible = "sdw20217010d00";
+		reg = <0 4>;
+		qcom,rx-port-mapping = <1 2 3 4 5>;
+	};
+};
+
+&swr2 {
+	status = "okay";
+
+	wcd_tx: wcd9380-tx@0,3 {
+		compatible = "sdw20217010d00";
+		reg = <0 3>;
+		qcom,tx-port-mapping = <2 3 4 5>;
+	};
+};
+
 &tlmm {
 	gpio-reserved-ranges = <28 4>, <40 4>;
+
+	wcd938x_reset_default: wcd938x_reset_default {
+		mux {
+			pins = "gpio32";
+			function = "gpio";
+		};
+
+		config {
+			pins = "gpio32";
+			drive-strength = <16>;
+			output-high;
+		};
+	};
+
+	wcd938x_reset_sleep: wcd938x_reset_sleep {
+		mux {
+			pins = "gpio32";
+			function = "gpio";
+		};
+
+		config {
+			pins = "gpio32";
+			drive-strength = <16>;
+			bias-disable;
+			output-low;
+		};
+	};
+};
+
+&txmacro {
+	status = "okay";
 };
 
 &uart12 {
diff --git a/arch/arm64/boot/dts/qcom/sm8250-sony-xperia-edo.dtsi b/arch/arm64/boot/dts/qcom/sm8250-sony-xperia-edo.dtsi
index d63f7a9bc4e9..549e0a2aa9fe 100644
--- a/arch/arm64/boot/dts/qcom/sm8250-sony-xperia-edo.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8250-sony-xperia-edo.dtsi
@@ -57,7 +57,7 @@
 		 * case, they are both on &pm8150b_gpios: camera focus(2), camera snapshot(1).
 		 */
 
-		vol-down {
+		key-vol-down {
 			label = "Volume Down";
 			linux,code = <KEY_VOLUMEDOWN>;
 			gpios = <&pm8150_gpios 1 GPIO_ACTIVE_LOW>;
@@ -441,7 +441,35 @@
 	status = "okay";
 	clock-frequency = <1000000>;
 
-	/* Dual Cirrus Logic CS35L41 amps @ 40, 41 */
+	cs35l41_l: cs35l41@40 {
+		compatible = "cirrus,cs35l41";
+		reg = <0x40>;
+		interrupt-parent = <&tlmm>;
+		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+		reset-gpios = <&tlmm 10 GPIO_ACTIVE_HIGH>;
+		cirrus,boost-peak-milliamp = <4000>;
+		cirrus,boost-ind-nanohenry = <1000>;
+		cirrus,boost-cap-microfarad = <15>;
+		cirrus,asp-sdout-hiz = <3>;
+		cirrus,gpio2-src-select = <2>;
+		cirrus,gpio2-output-enable;
+		#sound-dai-cells = <1>;
+	};
+
+	cs35l41_r: cs35l41@41 {
+		compatible = "cirrus,cs35l41";
+		reg = <0x41>;
+		interrupt-parent = <&tlmm>;
+		interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
+		reset-gpios = <&tlmm 10 GPIO_ACTIVE_HIGH>;
+		cirrus,boost-peak-milliamp = <4000>;
+		cirrus,boost-ind-nanohenry = <1000>;
+		cirrus,boost-cap-microfarad = <15>;
+		cirrus,asp-sdout-hiz = <3>;
+		cirrus,gpio2-src-select = <2>;
+		cirrus,gpio2-output-enable;
+		#sound-dai-cells = <1>;
+	};
 };
 
 &i2c5 {
diff --git a/arch/arm64/boot/dts/qcom/sm8250.dtsi b/arch/arm64/boot/dts/qcom/sm8250.dtsi
index 6f6129b39c9c..a5b62cadb129 100644
--- a/arch/arm64/boot/dts/qcom/sm8250.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8250.dtsi
@@ -8,6 +8,8 @@
 #include <dt-bindings/clock/qcom,gcc-sm8250.h>
 #include <dt-bindings/clock/qcom,gpucc-sm8250.h>
 #include <dt-bindings/clock/qcom,rpmh.h>
+#include <dt-bindings/clock/qcom,sm8250-lpass-aoncc.h>
+#include <dt-bindings/clock/qcom,sm8250-lpass-audiocc.h>
 #include <dt-bindings/dma/qcom-gpi.h>
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/interconnect/qcom,osm-l3.h>
@@ -18,6 +20,7 @@
 #include <dt-bindings/soc/qcom,rpmh-rsc.h>
 #include <dt-bindings/sound/qcom,q6afe.h>
 #include <dt-bindings/thermal/thermal.h>
+#include <dt-bindings/clock/qcom,camcc-sm8250.h>
 #include <dt-bindings/clock/qcom,videocc-sm8250.h>
 
 / {
@@ -98,7 +101,12 @@
 			capacity-dmips-mhz = <448>;
 			dynamic-power-coefficient = <205>;
 			next-level-cache = <&L2_0>;
+			power-domains = <&CPU_PD0>;
+			power-domain-names = "psci";
 			qcom,freq-domain = <&cpufreq_hw 0>;
+			operating-points-v2 = <&cpu0_opp_table>;
+			interconnects = <&gem_noc MASTER_AMPSS_M0 &mc_virt SLAVE_EBI_CH0>,
+					<&epss_l3 MASTER_OSM_L3_APPS &epss_l3 SLAVE_OSM_L3>;
 			#cooling-cells = <2>;
 			L2_0: l2-cache {
 				compatible = "cache";
@@ -117,7 +125,12 @@
 			capacity-dmips-mhz = <448>;
 			dynamic-power-coefficient = <205>;
 			next-level-cache = <&L2_100>;
+			power-domains = <&CPU_PD1>;
+			power-domain-names = "psci";
 			qcom,freq-domain = <&cpufreq_hw 0>;
+			operating-points-v2 = <&cpu0_opp_table>;
+			interconnects = <&gem_noc MASTER_AMPSS_M0 &mc_virt SLAVE_EBI_CH0>,
+					<&epss_l3 MASTER_OSM_L3_APPS &epss_l3 SLAVE_OSM_L3>;
 			#cooling-cells = <2>;
 			L2_100: l2-cache {
 				compatible = "cache";
@@ -133,7 +146,12 @@
 			capacity-dmips-mhz = <448>;
 			dynamic-power-coefficient = <205>;
 			next-level-cache = <&L2_200>;
+			power-domains = <&CPU_PD2>;
+			power-domain-names = "psci";
 			qcom,freq-domain = <&cpufreq_hw 0>;
+			operating-points-v2 = <&cpu0_opp_table>;
+			interconnects = <&gem_noc MASTER_AMPSS_M0 &mc_virt SLAVE_EBI_CH0>,
+					<&epss_l3 MASTER_OSM_L3_APPS &epss_l3 SLAVE_OSM_L3>;
 			#cooling-cells = <2>;
 			L2_200: l2-cache {
 				compatible = "cache";
@@ -149,7 +167,12 @@
 			capacity-dmips-mhz = <448>;
 			dynamic-power-coefficient = <205>;
 			next-level-cache = <&L2_300>;
+			power-domains = <&CPU_PD3>;
+			power-domain-names = "psci";
 			qcom,freq-domain = <&cpufreq_hw 0>;
+			operating-points-v2 = <&cpu0_opp_table>;
+			interconnects = <&gem_noc MASTER_AMPSS_M0 &mc_virt SLAVE_EBI_CH0>,
+					<&epss_l3 MASTER_OSM_L3_APPS &epss_l3 SLAVE_OSM_L3>;
 			#cooling-cells = <2>;
 			L2_300: l2-cache {
 				compatible = "cache";
@@ -165,7 +188,12 @@
 			capacity-dmips-mhz = <1024>;
 			dynamic-power-coefficient = <379>;
 			next-level-cache = <&L2_400>;
+			power-domains = <&CPU_PD4>;
+			power-domain-names = "psci";
 			qcom,freq-domain = <&cpufreq_hw 1>;
+			operating-points-v2 = <&cpu4_opp_table>;
+			interconnects = <&gem_noc MASTER_AMPSS_M0 &mc_virt SLAVE_EBI_CH0>,
+					<&epss_l3 MASTER_OSM_L3_APPS &epss_l3 SLAVE_OSM_L3>;
 			#cooling-cells = <2>;
 			L2_400: l2-cache {
 				compatible = "cache";
@@ -181,7 +209,12 @@
 			capacity-dmips-mhz = <1024>;
 			dynamic-power-coefficient = <379>;
 			next-level-cache = <&L2_500>;
+			power-domains = <&CPU_PD5>;
+			power-domain-names = "psci";
 			qcom,freq-domain = <&cpufreq_hw 1>;
+			operating-points-v2 = <&cpu4_opp_table>;
+			interconnects = <&gem_noc MASTER_AMPSS_M0 &mc_virt SLAVE_EBI_CH0>,
+					<&epss_l3 MASTER_OSM_L3_APPS &epss_l3 SLAVE_OSM_L3>;
 			#cooling-cells = <2>;
 			L2_500: l2-cache {
 				compatible = "cache";
@@ -198,7 +231,12 @@
 			capacity-dmips-mhz = <1024>;
 			dynamic-power-coefficient = <379>;
 			next-level-cache = <&L2_600>;
+			power-domains = <&CPU_PD6>;
+			power-domain-names = "psci";
 			qcom,freq-domain = <&cpufreq_hw 1>;
+			operating-points-v2 = <&cpu4_opp_table>;
+			interconnects = <&gem_noc MASTER_AMPSS_M0 &mc_virt SLAVE_EBI_CH0>,
+					<&epss_l3 MASTER_OSM_L3_APPS &epss_l3 SLAVE_OSM_L3>;
 			#cooling-cells = <2>;
 			L2_600: l2-cache {
 				compatible = "cache";
@@ -214,7 +252,12 @@
 			capacity-dmips-mhz = <1024>;
 			dynamic-power-coefficient = <444>;
 			next-level-cache = <&L2_700>;
+			power-domains = <&CPU_PD7>;
+			power-domain-names = "psci";
 			qcom,freq-domain = <&cpufreq_hw 2>;
+			operating-points-v2 = <&cpu7_opp_table>;
+			interconnects = <&gem_noc MASTER_AMPSS_M0 &mc_virt SLAVE_EBI_CH0>,
+					<&epss_l3 MASTER_OSM_L3_APPS &epss_l3 SLAVE_OSM_L3>;
 			#cooling-cells = <2>;
 			L2_700: l2-cache {
 				compatible = "cache";
@@ -257,11 +300,337 @@
 				};
 			};
 		};
+
+		idle-states {
+			entry-method = "psci";
+
+			LITTLE_CPU_SLEEP_0: cpu-sleep-0-0 {
+				compatible = "arm,idle-state";
+				idle-state-name = "silver-rail-power-collapse";
+				arm,psci-suspend-param = <0x40000004>;
+				entry-latency-us = <360>;
+				exit-latency-us = <531>;
+				min-residency-us = <3934>;
+				local-timer-stop;
+			};
+
+			BIG_CPU_SLEEP_0: cpu-sleep-1-0 {
+				compatible = "arm,idle-state";
+				idle-state-name = "gold-rail-power-collapse";
+				arm,psci-suspend-param = <0x40000004>;
+				entry-latency-us = <702>;
+				exit-latency-us = <1061>;
+				min-residency-us = <4488>;
+				local-timer-stop;
+			};
+		};
+
+		domain-idle-states {
+			CLUSTER_SLEEP_0: cluster-sleep-0 {
+				compatible = "domain-idle-state";
+				idle-state-name = "cluster-llcc-off";
+				arm,psci-suspend-param = <0x4100c244>;
+				entry-latency-us = <3264>;
+				exit-latency-us = <6562>;
+				min-residency-us = <9987>;
+				local-timer-stop;
+			};
+		};
+	};
+
+	cpu0_opp_table: opp-table-cpu0 {
+		compatible = "operating-points-v2";
+		opp-shared;
+
+		cpu0_opp1: opp-300000000 {
+			opp-hz = /bits/ 64 <300000000>;
+			opp-peak-kBps = <800000 9600000>;
+		};
+
+		cpu0_opp2: opp-403200000 {
+			opp-hz = /bits/ 64 <403200000>;
+			opp-peak-kBps = <800000 9600000>;
+		};
+
+		cpu0_opp3: opp-518400000 {
+			opp-hz = /bits/ 64 <518400000>;
+			opp-peak-kBps = <800000 16588800>;
+		};
+
+		cpu0_opp4: opp-614400000 {
+			opp-hz = /bits/ 64 <614400000>;
+			opp-peak-kBps = <800000 16588800>;
+		};
+
+		cpu0_opp5: opp-691200000 {
+			opp-hz = /bits/ 64 <691200000>;
+			opp-peak-kBps = <800000 19660800>;
+		};
+
+		cpu0_opp6: opp-787200000 {
+			opp-hz = /bits/ 64 <787200000>;
+			opp-peak-kBps = <1804000 19660800>;
+		};
+
+		cpu0_opp7: opp-883200000 {
+			opp-hz = /bits/ 64 <883200000>;
+			opp-peak-kBps = <1804000 23347200>;
+		};
+
+		cpu0_opp8: opp-979200000 {
+			opp-hz = /bits/ 64 <979200000>;
+			opp-peak-kBps = <1804000 26419200>;
+		};
+
+		cpu0_opp9: opp-1075200000 {
+			opp-hz = /bits/ 64 <1075200000>;
+			opp-peak-kBps = <1804000 29491200>;
+		};
+
+		cpu0_opp10: opp-1171200000 {
+			opp-hz = /bits/ 64 <1171200000>;
+			opp-peak-kBps = <1804000 32563200>;
+		};
+
+		cpu0_opp11: opp-1248000000 {
+			opp-hz = /bits/ 64 <1248000000>;
+			opp-peak-kBps = <1804000 36249600>;
+		};
+
+		cpu0_opp12: opp-1344000000 {
+			opp-hz = /bits/ 64 <1344000000>;
+			opp-peak-kBps = <2188000 36249600>;
+		};
+
+		cpu0_opp13: opp-1420800000 {
+			opp-hz = /bits/ 64 <1420800000>;
+			opp-peak-kBps = <2188000 39321600>;
+		};
+
+		cpu0_opp14: opp-1516800000 {
+			opp-hz = /bits/ 64 <1516800000>;
+			opp-peak-kBps = <3072000 42393600>;
+		};
+
+		cpu0_opp15: opp-1612800000 {
+			opp-hz = /bits/ 64 <1612800000>;
+			opp-peak-kBps = <3072000 42393600>;
+		};
+
+		cpu0_opp16: opp-1708800000 {
+			opp-hz = /bits/ 64 <1708800000>;
+			opp-peak-kBps = <4068000 42393600>;
+		};
+
+		cpu0_opp17: opp-1804800000 {
+			opp-hz = /bits/ 64 <1804800000>;
+			opp-peak-kBps = <4068000 42393600>;
+		};
+	};
+
+	cpu4_opp_table: opp-table-cpu4 {
+		compatible = "operating-points-v2";
+		opp-shared;
+
+		cpu4_opp1: opp-710400000 {
+			opp-hz = /bits/ 64 <710400000>;
+			opp-peak-kBps = <1804000 19660800>;
+		};
+
+		cpu4_opp2: opp-825600000 {
+			opp-hz = /bits/ 64 <825600000>;
+			opp-peak-kBps = <2188000 23347200>;
+		};
+
+		cpu4_opp3: opp-940800000 {
+			opp-hz = /bits/ 64 <940800000>;
+			opp-peak-kBps = <2188000 26419200>;
+		};
+
+		cpu4_opp4: opp-1056000000 {
+			opp-hz = /bits/ 64 <1056000000>;
+			opp-peak-kBps = <3072000 26419200>;
+		};
+
+		cpu4_opp5: opp-1171200000 {
+			opp-hz = /bits/ 64 <1171200000>;
+			opp-peak-kBps = <3072000 29491200>;
+		};
+
+		cpu4_opp6: opp-1286400000 {
+			opp-hz = /bits/ 64 <1286400000>;
+			opp-peak-kBps = <4068000 29491200>;
+		};
+
+		cpu4_opp7: opp-1382400000 {
+			opp-hz = /bits/ 64 <1382400000>;
+			opp-peak-kBps = <4068000 32563200>;
+		};
+
+		cpu4_opp8: opp-1478400000 {
+			opp-hz = /bits/ 64 <1478400000>;
+			opp-peak-kBps = <4068000 32563200>;
+		};
+
+		cpu4_opp9: opp-1574400000 {
+			opp-hz = /bits/ 64 <1574400000>;
+			opp-peak-kBps = <5412000 39321600>;
+		};
+
+		cpu4_opp10: opp-1670400000 {
+			opp-hz = /bits/ 64 <1670400000>;
+			opp-peak-kBps = <5412000 42393600>;
+		};
+
+		cpu4_opp11: opp-1766400000 {
+			opp-hz = /bits/ 64 <1766400000>;
+			opp-peak-kBps = <5412000 45465600>;
+		};
+
+		cpu4_opp12: opp-1862400000 {
+			opp-hz = /bits/ 64 <1862400000>;
+			opp-peak-kBps = <6220000 45465600>;
+		};
+
+		cpu4_opp13: opp-1958400000 {
+			opp-hz = /bits/ 64 <1958400000>;
+			opp-peak-kBps = <6220000 48537600>;
+		};
+
+		cpu4_opp14: opp-2054400000 {
+			opp-hz = /bits/ 64 <2054400000>;
+			opp-peak-kBps = <7216000 48537600>;
+		};
+
+		cpu4_opp15: opp-2150400000 {
+			opp-hz = /bits/ 64 <2150400000>;
+			opp-peak-kBps = <7216000 51609600>;
+		};
+
+		cpu4_opp16: opp-2246400000 {
+			opp-hz = /bits/ 64 <2246400000>;
+			opp-peak-kBps = <7216000 51609600>;
+		};
+
+		cpu4_opp17: opp-2342400000 {
+			opp-hz = /bits/ 64 <2342400000>;
+			opp-peak-kBps = <8368000 51609600>;
+		};
+
+		cpu4_opp18: opp-2419200000 {
+			opp-hz = /bits/ 64 <2419200000>;
+			opp-peak-kBps = <8368000 51609600>;
+		};
+	};
+
+	cpu7_opp_table: opp-table-cpu7 {
+		compatible = "operating-points-v2";
+		opp-shared;
+
+		cpu7_opp1: opp-844800000 {
+			opp-hz = /bits/ 64 <844800000>;
+			opp-peak-kBps = <2188000 19660800>;
+		};
+
+		cpu7_opp2: opp-960000000 {
+			opp-hz = /bits/ 64 <960000000>;
+			opp-peak-kBps = <2188000 26419200>;
+		};
+
+		cpu7_opp3: opp-1075200000 {
+			opp-hz = /bits/ 64 <1075200000>;
+			opp-peak-kBps = <3072000 26419200>;
+		};
+
+		cpu7_opp4: opp-1190400000 {
+			opp-hz = /bits/ 64 <1190400000>;
+			opp-peak-kBps = <3072000 29491200>;
+		};
+
+		cpu7_opp5: opp-1305600000 {
+			opp-hz = /bits/ 64 <1305600000>;
+			opp-peak-kBps = <4068000 32563200>;
+		};
+
+		cpu7_opp6: opp-1401600000 {
+			opp-hz = /bits/ 64 <1401600000>;
+			opp-peak-kBps = <4068000 32563200>;
+		};
+
+		cpu7_opp7: opp-1516800000 {
+			opp-hz = /bits/ 64 <1516800000>;
+			opp-peak-kBps = <4068000 36249600>;
+		};
+
+		cpu7_opp8: opp-1632000000 {
+			opp-hz = /bits/ 64 <1632000000>;
+			opp-peak-kBps = <5412000 39321600>;
+		};
+
+		cpu7_opp9: opp-1747200000 {
+			opp-hz = /bits/ 64 <1708800000>;
+			opp-peak-kBps = <5412000 42393600>;
+		};
+
+		cpu7_opp10: opp-1862400000 {
+			opp-hz = /bits/ 64 <1862400000>;
+			opp-peak-kBps = <6220000 45465600>;
+		};
+
+		cpu7_opp11: opp-1977600000 {
+			opp-hz = /bits/ 64 <1977600000>;
+			opp-peak-kBps = <6220000 48537600>;
+		};
+
+		cpu7_opp12: opp-2073600000 {
+			opp-hz = /bits/ 64 <2073600000>;
+			opp-peak-kBps = <7216000 48537600>;
+		};
+
+		cpu7_opp13: opp-2169600000 {
+			opp-hz = /bits/ 64 <2169600000>;
+			opp-peak-kBps = <7216000 51609600>;
+		};
+
+		cpu7_opp14: opp-2265600000 {
+			opp-hz = /bits/ 64 <2265600000>;
+			opp-peak-kBps = <7216000 51609600>;
+		};
+
+		cpu7_opp15: opp-2361600000 {
+			opp-hz = /bits/ 64 <2361600000>;
+			opp-peak-kBps = <8368000 51609600>;
+		};
+
+		cpu7_opp16: opp-2457600000 {
+			opp-hz = /bits/ 64 <2457600000>;
+			opp-peak-kBps = <8368000 51609600>;
+		};
+
+		cpu7_opp17: opp-2553600000 {
+			opp-hz = /bits/ 64 <2553600000>;
+			opp-peak-kBps = <8368000 51609600>;
+		};
+
+		cpu7_opp18: opp-2649600000 {
+			opp-hz = /bits/ 64 <2649600000>;
+			opp-peak-kBps = <8368000 51609600>;
+		};
+
+		cpu7_opp19: opp-2745600000 {
+			opp-hz = /bits/ 64 <2745600000>;
+			opp-peak-kBps = <8368000 51609600>;
+		};
+
+		cpu7_opp20: opp-2841600000 {
+			opp-hz = /bits/ 64 <2841600000>;
+			opp-peak-kBps = <8368000 51609600>;
+		};
 	};
 
 	firmware {
 		scm: scm {
-			compatible = "qcom,scm";
+			compatible = "qcom,scm-sm8250", "qcom,scm";
 			#reset-cells = <1>;
 		};
 	};
@@ -280,6 +649,78 @@
 	psci {
 		compatible = "arm,psci-1.0";
 		method = "smc";
+
+		CPU_PD0: cpu0 {
+			#power-domain-cells = <0>;
+			power-domains = <&CLUSTER_PD>;
+			domain-idle-states = <&LITTLE_CPU_SLEEP_0>;
+		};
+
+		CPU_PD1: cpu1 {
+			#power-domain-cells = <0>;
+			power-domains = <&CLUSTER_PD>;
+			domain-idle-states = <&LITTLE_CPU_SLEEP_0>;
+		};
+
+		CPU_PD2: cpu2 {
+			#power-domain-cells = <0>;
+			power-domains = <&CLUSTER_PD>;
+			domain-idle-states = <&LITTLE_CPU_SLEEP_0>;
+		};
+
+		CPU_PD3: cpu3 {
+			#power-domain-cells = <0>;
+			power-domains = <&CLUSTER_PD>;
+			domain-idle-states = <&LITTLE_CPU_SLEEP_0>;
+		};
+
+		CPU_PD4: cpu4 {
+			#power-domain-cells = <0>;
+			power-domains = <&CLUSTER_PD>;
+			domain-idle-states = <&BIG_CPU_SLEEP_0>;
+		};
+
+		CPU_PD5: cpu5 {
+			#power-domain-cells = <0>;
+			power-domains = <&CLUSTER_PD>;
+			domain-idle-states = <&BIG_CPU_SLEEP_0>;
+		};
+
+		CPU_PD6: cpu6 {
+			#power-domain-cells = <0>;
+			power-domains = <&CLUSTER_PD>;
+			domain-idle-states = <&BIG_CPU_SLEEP_0>;
+		};
+
+		CPU_PD7: cpu7 {
+			#power-domain-cells = <0>;
+			power-domains = <&CLUSTER_PD>;
+			domain-idle-states = <&BIG_CPU_SLEEP_0>;
+		};
+
+		CLUSTER_PD: cpu-cluster0 {
+			#power-domain-cells = <0>;
+			domain-idle-states = <&CLUSTER_SLEEP_0>;
+		};
+	};
+
+	qup_opp_table: opp-table-qup {
+		compatible = "operating-points-v2";
+
+		opp-50000000 {
+			opp-hz = /bits/ 64 <50000000>;
+			required-opps = <&rpmhpd_opp_min_svs>;
+		};
+
+		opp-75000000 {
+			opp-hz = /bits/ 64 <75000000>;
+			required-opps = <&rpmhpd_opp_low_svs>;
+		};
+
+		opp-120000000 {
+			opp-hz = /bits/ 64 <120000000>;
+			required-opps = <&rpmhpd_opp_svs>;
+		};
 	};
 
 	reserved-memory {
@@ -494,25 +935,6 @@
 			clock-names = "core";
 		};
 
-		qup_opp_table: qup-opp-table {
-			compatible = "operating-points-v2";
-
-			opp-50000000 {
-				opp-hz = /bits/ 64 <50000000>;
-				required-opps = <&rpmhpd_opp_min_svs>;
-			};
-
-			opp-75000000 {
-				opp-hz = /bits/ 64 <75000000>;
-				required-opps = <&rpmhpd_opp_low_svs>;
-			};
-
-			opp-120000000 {
-				opp-hz = /bits/ 64 <120000000>;
-				required-opps = <&rpmhpd_opp_svs>;
-			};
-		};
-
 		gpi_dma2: dma-controller@800000 {
 			compatible = "qcom,sm8250-gpi-dma";
 			reg = <0 0x00800000 0 0x70000>;
@@ -1370,7 +1792,7 @@
 		};
 
 		pcie0: pci@1c00000 {
-			compatible = "qcom,pcie-sm8250", "snps,dw-pcie";
+			compatible = "qcom,pcie-sm8250";
 			reg = <0 0x01c00000 0 0x3000>,
 			      <0 0x60000000 0 0xf1d>,
 			      <0 0x60000f20 0 0xa8>,
@@ -1388,8 +1810,16 @@
 			ranges = <0x01000000 0x0 0x60200000 0 0x60200000 0x0 0x100000>,
 				 <0x02000000 0x0 0x60300000 0 0x60300000 0x0 0x3d00000>;
 
-			interrupts = <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "msi";
+			interrupts = <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "msi0", "msi1", "msi2", "msi3",
+					  "msi4", "msi5", "msi6", "msi7";
 			#interrupt-cells = <1>;
 			interrupt-map-mask = <0 0 0 0x7>;
 			interrupt-map = <0 0 0 1 &intc 0 149 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
@@ -1426,8 +1856,8 @@
 			phys = <&pcie0_lane>;
 			phy-names = "pciephy";
 
-			perst-gpio = <&tlmm 79 GPIO_ACTIVE_LOW>;
-			enable-gpio = <&tlmm 81 GPIO_ACTIVE_HIGH>;
+			perst-gpios = <&tlmm 79 GPIO_ACTIVE_LOW>;
+			wake-gpios = <&tlmm 81 GPIO_ACTIVE_HIGH>;
 
 			pinctrl-names = "default";
 			pinctrl-0 = <&pcie0_default_state>;
@@ -1464,12 +1894,14 @@
 				clock-names = "pipe0";
 
 				#phy-cells = <0>;
+
+				#clock-cells = <0>;
 				clock-output-names = "pcie_0_pipe_clk";
 			};
 		};
 
 		pcie1: pci@1c08000 {
-			compatible = "qcom,pcie-sm8250", "snps,dw-pcie";
+			compatible = "qcom,pcie-sm8250";
 			reg = <0 0x01c08000 0 0x3000>,
 			      <0 0x40000000 0 0xf1d>,
 			      <0 0x40000f20 0 0xa8>,
@@ -1487,7 +1919,7 @@
 			ranges = <0x01000000 0x0 0x40200000 0x0 0x40200000 0x0 0x100000>,
 				 <0x02000000 0x0 0x40300000 0x0 0x40300000 0x0 0x1fd00000>;
 
-			interrupts = <GIC_SPI 306 IRQ_TYPE_EDGE_RISING>;
+			interrupts = <GIC_SPI 307 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "msi";
 			#interrupt-cells = <1>;
 			interrupt-map-mask = <0 0 0 0x7>;
@@ -1530,8 +1962,8 @@
 			phys = <&pcie1_lane>;
 			phy-names = "pciephy";
 
-			perst-gpio = <&tlmm 82 GPIO_ACTIVE_LOW>;
-			enable-gpio = <&tlmm 84 GPIO_ACTIVE_HIGH>;
+			perst-gpios = <&tlmm 82 GPIO_ACTIVE_LOW>;
+			wake-gpios = <&tlmm 84 GPIO_ACTIVE_HIGH>;
 
 			pinctrl-names = "default";
 			pinctrl-0 = <&pcie1_default_state>;
@@ -1570,12 +2002,14 @@
 				clock-names = "pipe0";
 
 				#phy-cells = <0>;
+
+				#clock-cells = <0>;
 				clock-output-names = "pcie_1_pipe_clk";
 			};
 		};
 
 		pcie2: pci@1c10000 {
-			compatible = "qcom,pcie-sm8250", "snps,dw-pcie";
+			compatible = "qcom,pcie-sm8250";
 			reg = <0 0x01c10000 0 0x3000>,
 			      <0 0x64000000 0 0xf1d>,
 			      <0 0x64000f20 0 0xa8>,
@@ -1593,7 +2027,7 @@
 			ranges = <0x01000000 0x0 0x64200000 0x0 0x64200000 0x0 0x100000>,
 				 <0x02000000 0x0 0x64300000 0x0 0x64300000 0x0 0x3d00000>;
 
-			interrupts = <GIC_SPI 236 IRQ_TYPE_EDGE_RISING>;
+			interrupts = <GIC_SPI 243 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "msi";
 			#interrupt-cells = <1>;
 			interrupt-map-mask = <0 0 0 0x7>;
@@ -1636,8 +2070,8 @@
 			phys = <&pcie2_lane>;
 			phy-names = "pciephy";
 
-			perst-gpio = <&tlmm 85 GPIO_ACTIVE_LOW>;
-			enable-gpio = <&tlmm 87 GPIO_ACTIVE_HIGH>;
+			perst-gpios = <&tlmm 85 GPIO_ACTIVE_LOW>;
+			wake-gpios = <&tlmm 87 GPIO_ACTIVE_HIGH>;
 
 			pinctrl-names = "default";
 			pinctrl-0 = <&pcie2_default_state>;
@@ -1676,6 +2110,8 @@
 				clock-names = "pipe0";
 
 				#phy-cells = <0>;
+
+				#clock-cells = <0>;
 				clock-output-names = "pcie_2_pipe_clk";
 			};
 		};
@@ -1768,11 +2204,11 @@
 		wsamacro: codec@3240000 {
 			compatible = "qcom,sm8250-lpass-wsa-macro";
 			reg = <0 0x03240000 0 0x1000>;
-			clocks = <&audiocc 1>,
-				 <&audiocc 0>,
+			clocks = <&audiocc LPASS_CDC_WSA_MCLK>,
+				 <&audiocc LPASS_CDC_WSA_NPL>,
 				 <&q6afecc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
 				 <&q6afecc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
-				 <&aoncc 0>,
+				 <&aoncc LPASS_CDC_VA_MCLK>,
 				 <&vamacro>;
 
 			clock-names = "mclk", "npl", "macro", "dcodec", "va", "fsgen";
@@ -1819,7 +2255,7 @@
 		vamacro: codec@3370000 {
 			compatible = "qcom,sm8250-lpass-va-macro";
 			reg = <0 0x03370000 0 0x1000>;
-			clocks = <&aoncc 0>,
+			clocks = <&aoncc LPASS_CDC_VA_MCLK>,
 				<&q6afecc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
 				<&q6afecc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>;
 
@@ -1831,6 +2267,105 @@
 			#sound-dai-cells = <1>;
 		};
 
+		rxmacro: rxmacro@3200000 {
+			pinctrl-names = "default";
+			pinctrl-0 = <&rx_swr_active>;
+			compatible = "qcom,sm8250-lpass-rx-macro";
+			reg = <0 0x3200000 0 0x1000>;
+			status = "disabled";
+
+			clocks = <&q6afecc LPASS_CLK_ID_TX_CORE_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+				<&q6afecc LPASS_CLK_ID_TX_CORE_NPL_MCLK  LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+				<&q6afecc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+				<&q6afecc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+				<&vamacro>;
+
+			clock-names = "mclk", "npl", "macro", "dcodec", "fsgen";
+
+			#clock-cells = <0>;
+			clock-frequency = <9600000>;
+			clock-output-names = "mclk";
+			#sound-dai-cells = <1>;
+		};
+
+		swr1: soundwire-controller@3210000 {
+			reg = <0 0x3210000 0 0x2000>;
+			compatible = "qcom,soundwire-v1.5.1";
+			status = "disabled";
+			interrupts = <GIC_SPI 298 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&rxmacro>;
+			clock-names = "iface";
+			label = "RX";
+			qcom,din-ports = <0>;
+			qcom,dout-ports = <5>;
+
+			qcom,ports-sinterval-low =	/bits/ 8 <0x03 0x1F 0x1F 0x07 0x00>;
+			qcom,ports-offset1 =		/bits/ 8 <0x00 0x00 0x0B 0x01 0x00>;
+			qcom,ports-offset2 =		/bits/ 8 <0x00 0x00 0x0B 0x00 0x00>;
+			qcom,ports-hstart =		/bits/ 8 <0xFF 0x03 0xFF 0xFF 0xFF>;
+			qcom,ports-hstop =		/bits/ 8 <0xFF 0x06 0xFF 0xFF 0xFF>;
+			qcom,ports-word-length =	/bits/ 8 <0x01 0x07 0x04 0xFF 0xFF>;
+			qcom,ports-block-pack-mode =	/bits/ 8 <0xFF 0x00 0x01 0xFF 0xFF>;
+			qcom,ports-lane-control =	/bits/ 8 <0x01 0x00 0x00 0x00 0x00>;
+			qcom,ports-block-group-count =	/bits/ 8 <0xFF 0xFF 0xFF 0xFF 0x00>;
+
+			#sound-dai-cells = <1>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+		};
+
+		txmacro: txmacro@3220000 {
+			pinctrl-names = "default";
+			pinctrl-0 = <&tx_swr_active>;
+			compatible = "qcom,sm8250-lpass-tx-macro";
+			reg = <0 0x3220000 0 0x1000>;
+			status = "disabled";
+
+			clocks = <&q6afecc LPASS_CLK_ID_TX_CORE_MCLK LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+				 <&q6afecc LPASS_CLK_ID_TX_CORE_NPL_MCLK  LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+				 <&q6afecc LPASS_HW_MACRO_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+				 <&q6afecc LPASS_HW_DCODEC_VOTE LPASS_CLK_ATTRIBUTE_COUPLE_NO>,
+				 <&vamacro>;
+
+			clock-names = "mclk", "npl", "macro", "dcodec", "fsgen";
+
+			#clock-cells = <0>;
+			clock-frequency = <9600000>;
+			clock-output-names = "mclk";
+			#address-cells = <2>;
+			#size-cells = <2>;
+			#sound-dai-cells = <1>;
+		};
+
+		/* tx macro */
+		swr2: soundwire-controller@3230000 {
+			reg = <0 0x3230000 0 0x2000>;
+			compatible = "qcom,soundwire-v1.5.1";
+			interrupts-extended = <&intc GIC_SPI 297 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "core";
+			status = "disabled";
+
+			clocks = <&txmacro>;
+			clock-names = "iface";
+			label = "TX";
+
+			qcom,din-ports = <5>;
+			qcom,dout-ports = <0>;
+			qcom,ports-sinterval-low =	/bits/ 8 <0xFF 0x01 0x01 0x03 0x03>;
+			qcom,ports-offset1 =		/bits/ 8 <0xFF 0x01 0x00 0x02 0x00>;
+			qcom,ports-offset2 =		/bits/ 8 <0xFF 0x00 0x00 0x00 0x00>;
+			qcom,ports-block-pack-mode =	/bits/ 8 <0xFF 0xFF 0xFF 0xFF 0xFF>;
+			qcom,ports-hstart =		/bits/ 8 <0xFF 0xFF 0xFF 0xFF 0xFF>;
+			qcom,ports-hstop =		/bits/ 8 <0xFF 0xFF 0xFF 0xFF 0xFF>;
+			qcom,ports-word-length =	/bits/ 8 <0xFF 0xFF 0xFF 0xFF 0xFF>;
+			qcom,ports-block-group-count =	/bits/ 8 <0xFF 0xFF 0xFF 0xFF 0xFF>;
+			qcom,ports-lane-control =	/bits/ 8 <0xFF 0x00 0x01 0x00 0x01>;
+			qcom,port-offset = <1>;
+			#sound-dai-cells = <1>;
+			#address-cells = <2>;
+			#size-cells = <0>;
+		};
+
 		aoncc: clock-controller@3380000 {
 			compatible = "qcom,sm8250-lpass-aoncc";
 			reg = <0 0x03380000 0 0x40000>;
@@ -1923,12 +2458,73 @@
 					input-enable;
 				};
 			};
+
+			rx_swr_active: rx_swr-active-pins {
+				clk {
+					pins = "gpio3";
+					function = "swr_rx_clk";
+					drive-strength = <2>;
+					slew-rate = <1>;
+					bias-disable;
+				};
+
+				data {
+					pins = "gpio4", "gpio5";
+					function = "swr_rx_data";
+					drive-strength = <2>;
+					slew-rate = <1>;
+					bias-bus-hold;
+				};
+			};
+
+			tx_swr_active: tx_swr-active-pins {
+				clk {
+					pins = "gpio0";
+					function = "swr_tx_clk";
+					drive-strength = <2>;
+					slew-rate = <1>;
+					bias-disable;
+				};
+
+				data {
+					pins = "gpio1", "gpio2";
+					function = "swr_tx_data";
+					drive-strength = <2>;
+					slew-rate = <1>;
+					bias-bus-hold;
+				};
+			};
+
+			tx_swr_sleep: tx_swr-sleep-pins {
+				clk {
+					pins = "gpio0";
+					function = "swr_tx_clk";
+					drive-strength = <2>;
+					input-enable;
+					bias-pull-down;
+				};
+
+				data1 {
+					pins = "gpio1";
+					function = "swr_tx_data";
+					drive-strength = <2>;
+					input-enable;
+					bias-bus-hold;
+				};
+
+				data2 {
+					pins = "gpio2";
+					function = "swr_tx_data";
+					drive-strength = <2>;
+					input-enable;
+					bias-pull-down;
+				};
+			};
 		};
 
 		gpu: gpu@3d00000 {
 			compatible = "qcom,adreno-650.2",
 				     "qcom,adreno";
-			#stream-id-cells = <16>;
 
 			reg = <0 0x03d00000 0 0x40000>;
 			reg-names = "kgsl_3d0_reg_memory";
@@ -1989,7 +2585,7 @@
 		};
 
 		gmu: gmu@3d6a000 {
-			compatible="qcom,adreno-gmu-650.2", "qcom,adreno-gmu";
+			compatible = "qcom,adreno-gmu-650.2", "qcom,adreno-gmu";
 
 			reg = <0 0x03d6a000 0 0x30000>,
 			      <0 0x3de0000 0 0x10000>,
@@ -2043,7 +2639,7 @@
 		};
 
 		adreno_smmu: iommu@3da0000 {
-			compatible = "qcom,sm8250-smmu-500", "arm,mmu-500";
+			compatible = "qcom,sm8250-smmu-500", "qcom,adreno-smmu", "arm,mmu-500";
 			reg = <0 0x03da0000 0 0x10000>;
 			#iommu-cells = <2>;
 			#global-interrupts = <2>;
@@ -2107,6 +2703,7 @@
 					compatible = "qcom,fastrpc";
 					qcom,glink-channels = "fastrpcglink-apps-dsp";
 					label = "sdsp";
+					qcom,non-secure-domain;
 					#address-cells = <1>;
 					#size-cells = <0>;
 
@@ -2172,6 +2769,7 @@
 					compatible = "qcom,fastrpc";
 					qcom,glink-channels = "fastrpcglink-apps-dsp";
 					label = "cdsp";
+					qcom,non-secure-domain;
 					#address-cells = <1>;
 					#size-cells = <0>;
 
@@ -2335,7 +2933,7 @@
 			};
 		};
 
-		sdhc_2: sdhci@8804000 {
+		sdhc_2: mmc@8804000 {
 			compatible = "qcom,sm8250-sdhci", "qcom,sdhci-msm-v5";
 			reg = <0 0x08804000 0 0x1000>;
 
@@ -2355,7 +2953,7 @@
 
 			status = "disabled";
 
-			sdhc2_opp_table: sdhc2-opp-table {
+			sdhc2_opp_table: opp-table {
 				compatible = "operating-points-v2";
 
 				opp-19200000 {
@@ -2413,22 +3011,28 @@
 			clocks = <&gcc GCC_CFG_NOC_USB3_PRIM_AXI_CLK>,
 				 <&gcc GCC_USB30_PRIM_MASTER_CLK>,
 				 <&gcc GCC_AGGRE_USB3_PRIM_AXI_CLK>,
-				 <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
 				 <&gcc GCC_USB30_PRIM_SLEEP_CLK>,
+				 <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
 				 <&gcc GCC_USB3_SEC_CLKREF_EN>;
-			clock-names = "cfg_noc", "core", "iface", "mock_utmi",
-				      "sleep", "xo";
+			clock-names = "cfg_noc",
+				      "core",
+				      "iface",
+				      "sleep",
+				      "mock_utmi",
+				      "xo";
 
 			assigned-clocks = <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
 					  <&gcc GCC_USB30_PRIM_MASTER_CLK>;
 			assigned-clock-rates = <19200000>, <200000000>;
 
 			interrupts-extended = <&intc GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>,
-					      <&pdc 14 IRQ_TYPE_EDGE_BOTH>,
+					      <&pdc 17 IRQ_TYPE_LEVEL_HIGH>,
 					      <&pdc 15 IRQ_TYPE_EDGE_BOTH>,
-					      <&pdc 17 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "hs_phy_irq", "dp_hs_phy_irq",
-					  "dm_hs_phy_irq", "ss_phy_irq";
+					      <&pdc 14 IRQ_TYPE_EDGE_BOTH>;
+			interrupt-names = "hs_phy_irq",
+					  "ss_phy_irq",
+					  "dm_hs_phy_irq",
+					  "dp_hs_phy_irq";
 
 			power-domains = <&gcc USB30_PRIM_GDSC>;
 
@@ -2464,22 +3068,28 @@
 			clocks = <&gcc GCC_CFG_NOC_USB3_SEC_AXI_CLK>,
 				 <&gcc GCC_USB30_SEC_MASTER_CLK>,
 				 <&gcc GCC_AGGRE_USB3_SEC_AXI_CLK>,
-				 <&gcc GCC_USB30_SEC_MOCK_UTMI_CLK>,
 				 <&gcc GCC_USB30_SEC_SLEEP_CLK>,
+				 <&gcc GCC_USB30_SEC_MOCK_UTMI_CLK>,
 				 <&gcc GCC_USB3_SEC_CLKREF_EN>;
-			clock-names = "cfg_noc", "core", "iface", "mock_utmi",
-				      "sleep", "xo";
+			clock-names = "cfg_noc",
+				      "core",
+				      "iface",
+				      "sleep",
+				      "mock_utmi",
+				      "xo";
 
 			assigned-clocks = <&gcc GCC_USB30_SEC_MOCK_UTMI_CLK>,
 					  <&gcc GCC_USB30_SEC_MASTER_CLK>;
 			assigned-clock-rates = <19200000>, <200000000>;
 
 			interrupts-extended = <&intc GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>,
-					      <&pdc 12 IRQ_TYPE_EDGE_BOTH>,
+					      <&pdc 16 IRQ_TYPE_LEVEL_HIGH>,
 					      <&pdc 13 IRQ_TYPE_EDGE_BOTH>,
-					      <&pdc 16 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "hs_phy_irq", "dp_hs_phy_irq",
-					  "dm_hs_phy_irq", "ss_phy_irq";
+					      <&pdc 12 IRQ_TYPE_EDGE_BOTH>;
+			interrupt-names = "hs_phy_irq",
+					  "ss_phy_irq",
+					  "dm_hs_phy_irq",
+					  "dp_hs_phy_irq";
 
 			power-domains = <&gcc USB30_SEC_GDSC>;
 
@@ -2533,7 +3143,7 @@
 				compatible = "venus-encoder";
 			};
 
-			venus_opp_table: venus-opp-table {
+			venus_opp_table: opp-table {
 				compatible = "operating-points-v2";
 
 				opp-720000000 {
@@ -2572,6 +3182,257 @@
 			#power-domain-cells = <1>;
 		};
 
+		cci0: cci@ac4f000 {
+			compatible = "qcom,sm8250-cci";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			reg = <0 0x0ac4f000 0 0x1000>;
+			interrupts = <GIC_SPI 460 IRQ_TYPE_EDGE_RISING>;
+			power-domains = <&camcc TITAN_TOP_GDSC>;
+
+			clocks = <&camcc CAM_CC_CAMNOC_AXI_CLK>,
+				 <&camcc CAM_CC_SLOW_AHB_CLK_SRC>,
+				 <&camcc CAM_CC_CPAS_AHB_CLK>,
+				 <&camcc CAM_CC_CCI_0_CLK>,
+				 <&camcc CAM_CC_CCI_0_CLK_SRC>;
+			clock-names = "camnoc_axi",
+				      "slow_ahb_src",
+				      "cpas_ahb",
+				      "cci",
+				      "cci_src";
+
+			pinctrl-0 = <&cci0_default>;
+			pinctrl-1 = <&cci0_sleep>;
+			pinctrl-names = "default", "sleep";
+
+			status = "disabled";
+
+			cci0_i2c0: i2c-bus@0 {
+				reg = <0>;
+				clock-frequency = <1000000>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+
+			cci0_i2c1: i2c-bus@1 {
+				reg = <1>;
+				clock-frequency = <1000000>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+
+		cci1: cci@ac50000 {
+			compatible = "qcom,sm8250-cci";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			reg = <0 0x0ac50000 0 0x1000>;
+			interrupts = <GIC_SPI 271 IRQ_TYPE_EDGE_RISING>;
+			power-domains = <&camcc TITAN_TOP_GDSC>;
+
+			clocks = <&camcc CAM_CC_CAMNOC_AXI_CLK>,
+				 <&camcc CAM_CC_SLOW_AHB_CLK_SRC>,
+				 <&camcc CAM_CC_CPAS_AHB_CLK>,
+				 <&camcc CAM_CC_CCI_1_CLK>,
+				 <&camcc CAM_CC_CCI_1_CLK_SRC>;
+			clock-names = "camnoc_axi",
+				      "slow_ahb_src",
+				      "cpas_ahb",
+				      "cci",
+				      "cci_src";
+
+			pinctrl-0 = <&cci1_default>;
+			pinctrl-1 = <&cci1_sleep>;
+			pinctrl-names = "default", "sleep";
+
+			status = "disabled";
+
+			cci1_i2c0: i2c-bus@0 {
+				reg = <0>;
+				clock-frequency = <1000000>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+
+			cci1_i2c1: i2c-bus@1 {
+				reg = <1>;
+				clock-frequency = <1000000>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+
+		camss: camss@ac6a000 {
+			compatible = "qcom,sm8250-camss";
+			status = "disabled";
+
+			reg = <0 0xac6a000 0 0x2000>,
+			      <0 0xac6c000 0 0x2000>,
+			      <0 0xac6e000 0 0x1000>,
+			      <0 0xac70000 0 0x1000>,
+			      <0 0xac72000 0 0x1000>,
+			      <0 0xac74000 0 0x1000>,
+			      <0 0xacb4000 0 0xd000>,
+			      <0 0xacc3000 0 0xd000>,
+			      <0 0xacd9000 0 0x2200>,
+			      <0 0xacdb200 0 0x2200>;
+			reg-names = "csiphy0",
+				    "csiphy1",
+				    "csiphy2",
+				    "csiphy3",
+				    "csiphy4",
+				    "csiphy5",
+				    "vfe0",
+				    "vfe1",
+				    "vfe_lite0",
+				    "vfe_lite1";
+
+			interrupts = <GIC_SPI 477 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 478 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 479 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 448 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 464 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 466 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 468 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 359 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 465 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 467 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 469 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 360 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "csiphy0",
+					  "csiphy1",
+					  "csiphy2",
+					  "csiphy3",
+					  "csiphy4",
+					  "csiphy5",
+					  "csid0",
+					  "csid1",
+					  "csid2",
+					  "csid3",
+					  "vfe0",
+					  "vfe1",
+					  "vfe_lite0",
+					  "vfe_lite1";
+
+			power-domains = <&camcc IFE_0_GDSC>,
+					<&camcc IFE_1_GDSC>,
+					<&camcc TITAN_TOP_GDSC>;
+
+			clocks = <&gcc GCC_CAMERA_AHB_CLK>,
+				 <&gcc GCC_CAMERA_HF_AXI_CLK>,
+				 <&gcc GCC_CAMERA_SF_AXI_CLK>,
+				 <&camcc CAM_CC_CAMNOC_AXI_CLK>,
+				 <&camcc CAM_CC_CAMNOC_AXI_CLK_SRC>,
+				 <&camcc CAM_CC_CORE_AHB_CLK>,
+				 <&camcc CAM_CC_CPAS_AHB_CLK>,
+				 <&camcc CAM_CC_CSIPHY0_CLK>,
+				 <&camcc CAM_CC_CSI0PHYTIMER_CLK>,
+				 <&camcc CAM_CC_CSIPHY1_CLK>,
+				 <&camcc CAM_CC_CSI1PHYTIMER_CLK>,
+				 <&camcc CAM_CC_CSIPHY2_CLK>,
+				 <&camcc CAM_CC_CSI2PHYTIMER_CLK>,
+				 <&camcc CAM_CC_CSIPHY3_CLK>,
+				 <&camcc CAM_CC_CSI3PHYTIMER_CLK>,
+				 <&camcc CAM_CC_CSIPHY4_CLK>,
+				 <&camcc CAM_CC_CSI4PHYTIMER_CLK>,
+				 <&camcc CAM_CC_CSIPHY5_CLK>,
+				 <&camcc CAM_CC_CSI5PHYTIMER_CLK>,
+				 <&camcc CAM_CC_SLOW_AHB_CLK_SRC>,
+				 <&camcc CAM_CC_IFE_0_AHB_CLK>,
+				 <&camcc CAM_CC_IFE_0_AXI_CLK>,
+				 <&camcc CAM_CC_IFE_0_CLK>,
+				 <&camcc CAM_CC_IFE_0_CPHY_RX_CLK>,
+				 <&camcc CAM_CC_IFE_0_CSID_CLK>,
+				 <&camcc CAM_CC_IFE_0_AREG_CLK>,
+				 <&camcc CAM_CC_IFE_1_AHB_CLK>,
+				 <&camcc CAM_CC_IFE_1_AXI_CLK>,
+				 <&camcc CAM_CC_IFE_1_CLK>,
+				 <&camcc CAM_CC_IFE_1_CPHY_RX_CLK>,
+				 <&camcc CAM_CC_IFE_1_CSID_CLK>,
+				 <&camcc CAM_CC_IFE_1_AREG_CLK>,
+				 <&camcc CAM_CC_IFE_LITE_AHB_CLK>,
+				 <&camcc CAM_CC_IFE_LITE_AXI_CLK>,
+				 <&camcc CAM_CC_IFE_LITE_CLK>,
+				 <&camcc CAM_CC_IFE_LITE_CPHY_RX_CLK>,
+				 <&camcc CAM_CC_IFE_LITE_CSID_CLK>;
+
+			clock-names = "cam_ahb_clk",
+				      "cam_hf_axi",
+				      "cam_sf_axi",
+				      "camnoc_axi",
+				      "camnoc_axi_src",
+				      "core_ahb",
+				      "cpas_ahb",
+				      "csiphy0",
+				      "csiphy0_timer",
+				      "csiphy1",
+				      "csiphy1_timer",
+				      "csiphy2",
+				      "csiphy2_timer",
+				      "csiphy3",
+				      "csiphy3_timer",
+				      "csiphy4",
+				      "csiphy4_timer",
+				      "csiphy5",
+				      "csiphy5_timer",
+				      "slow_ahb_src",
+				      "vfe0_ahb",
+				      "vfe0_axi",
+				      "vfe0",
+				      "vfe0_cphy_rx",
+				      "vfe0_csid",
+				      "vfe0_areg",
+				      "vfe1_ahb",
+				      "vfe1_axi",
+				      "vfe1",
+				      "vfe1_cphy_rx",
+				      "vfe1_csid",
+				      "vfe1_areg",
+				      "vfe_lite_ahb",
+				      "vfe_lite_axi",
+				      "vfe_lite",
+				      "vfe_lite_cphy_rx",
+				      "vfe_lite_csid";
+
+			iommus = <&apps_smmu 0x800 0x400>,
+				 <&apps_smmu 0x801 0x400>,
+				 <&apps_smmu 0x840 0x400>,
+				 <&apps_smmu 0x841 0x400>,
+				 <&apps_smmu 0xc00 0x400>,
+				 <&apps_smmu 0xc01 0x400>,
+				 <&apps_smmu 0xc40 0x400>,
+				 <&apps_smmu 0xc41 0x400>;
+
+			interconnects = <&gem_noc MASTER_AMPSS_M0 &config_noc SLAVE_CAMERA_CFG>,
+					<&mmss_noc MASTER_CAMNOC_HF &mc_virt SLAVE_EBI_CH0>,
+					<&mmss_noc MASTER_CAMNOC_SF &mc_virt SLAVE_EBI_CH0>,
+					<&mmss_noc MASTER_CAMNOC_ICP &mc_virt SLAVE_EBI_CH0>;
+			interconnect-names = "cam_ahb",
+					     "cam_hf_0_mnoc",
+					     "cam_sf_0_mnoc",
+					     "cam_sf_icp_mnoc";
+		};
+
+		camcc: clock-controller@ad00000 {
+			compatible = "qcom,sm8250-camcc";
+			reg = <0 0x0ad00000 0 0x10000>;
+			clocks = <&gcc GCC_CAMERA_AHB_CLK>,
+				 <&rpmhcc RPMH_CXO_CLK>,
+				 <&rpmhcc RPMH_CXO_CLK_A>,
+				 <&sleep_clk>;
+			clock-names = "iface", "bi_tcxo", "bi_tcxo_ao", "sleep_clk";
+			power-domains = <&rpmhpd SM8250_MMCX>;
+			required-opps = <&rpmhpd_opp_low_svs>;
+			status = "disabled";
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+			#power-domain-cells = <1>;
+		};
+
 		mdss: mdss@ae00000 {
 			compatible = "qcom,sm8250-mdss";
 			reg = <0 0x0ae00000 0 0x1000>;
@@ -2589,9 +3450,6 @@
 				 <&dispcc DISP_CC_MDSS_MDP_CLK>;
 			clock-names = "iface", "bus", "nrt_bus", "core";
 
-			assigned-clocks = <&dispcc DISP_CC_MDSS_MDP_CLK>;
-			assigned-clock-rates = <460000000>;
-
 			interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-controller;
 			#interrupt-cells = <1>;
@@ -2604,7 +3462,7 @@
 			#size-cells = <2>;
 			ranges;
 
-			mdss_mdp: mdp@ae01000 {
+			mdss_mdp: display-controller@ae01000 {
 				compatible = "qcom,sm8250-dpu";
 				reg = <0 0x0ae01000 0 0x8f000>,
 				      <0 0x0aeb0000 0 0x2008>;
@@ -2616,16 +3474,14 @@
 					 <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
 				clock-names = "iface", "bus", "core", "vsync";
 
-				assigned-clocks = <&dispcc DISP_CC_MDSS_MDP_CLK>,
-						  <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
-				assigned-clock-rates = <460000000>,
-						       <19200000>;
+				assigned-clocks = <&dispcc DISP_CC_MDSS_VSYNC_CLK>;
+				assigned-clock-rates = <19200000>;
 
 				operating-points-v2 = <&mdp_opp_table>;
 				power-domains = <&rpmhpd SM8250_MMCX>;
 
 				interrupt-parent = <&mdss>;
-				interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
+				interrupts = <0>;
 
 				ports {
 					#address-cells = <1>;
@@ -2646,7 +3502,7 @@
 					};
 				};
 
-				mdp_opp_table: mdp-opp-table {
+				mdp_opp_table: opp-table {
 					compatible = "operating-points-v2";
 
 					opp-200000000 {
@@ -2677,7 +3533,7 @@
 				reg-names = "dsi_ctrl";
 
 				interrupt-parent = <&mdss>;
-				interrupts = <4 IRQ_TYPE_LEVEL_HIGH>;
+				interrupts = <4>;
 
 				clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK>,
 					 <&dispcc DISP_CC_MDSS_BYTE0_INTF_CLK>,
@@ -2723,6 +3579,25 @@
 						};
 					};
 				};
+
+				dsi_opp_table: opp-table {
+					compatible = "operating-points-v2";
+
+					opp-187500000 {
+						opp-hz = /bits/ 64 <187500000>;
+						required-opps = <&rpmhpd_opp_low_svs>;
+					};
+
+					opp-300000000 {
+						opp-hz = /bits/ 64 <300000000>;
+						required-opps = <&rpmhpd_opp_svs>;
+					};
+
+					opp-358000000 {
+						opp-hz = /bits/ 64 <358000000>;
+						required-opps = <&rpmhpd_opp_svs_l1>;
+					};
+				};
 			};
 
 			dsi0_phy: dsi-phy@ae94400 {
@@ -2750,7 +3625,7 @@
 				reg-names = "dsi_ctrl";
 
 				interrupt-parent = <&mdss>;
-				interrupts = <5 IRQ_TYPE_LEVEL_HIGH>;
+				interrupts = <5>;
 
 				clocks = <&dispcc DISP_CC_MDSS_BYTE1_CLK>,
 					 <&dispcc DISP_CC_MDSS_BYTE1_INTF_CLK>,
@@ -2815,25 +3690,6 @@
 				clock-names = "iface", "ref";
 
 				status = "disabled";
-
-				dsi_opp_table: dsi-opp-table {
-					compatible = "operating-points-v2";
-
-					opp-187500000 {
-						opp-hz = /bits/ 64 <187500000>;
-						required-opps = <&rpmhpd_opp_low_svs>;
-					};
-
-					opp-300000000 {
-						opp-hz = /bits/ 64 <300000000>;
-						required-opps = <&rpmhpd_opp_svs>;
-					};
-
-					opp-358000000 {
-						opp-hz = /bits/ 64 <358000000>;
-						required-opps = <&rpmhpd_opp_svs_l1>;
-					};
-				};
 			};
 		};
 
@@ -2894,7 +3750,7 @@
 		};
 
 		aoss_qmp: power-controller@c300000 {
-			compatible = "qcom,sm8250-aoss-qmp";
+			compatible = "qcom,sm8250-aoss-qmp", "qcom,aoss-qmp";
 			reg = <0 0x0c300000 0 0x400>;
 			interrupts-extended = <&ipcc IPCC_CLIENT_AOP
 						     IPCC_MPROC_SIGNAL_GLINK_QMP
@@ -2942,6 +3798,86 @@
 			gpio-ranges = <&tlmm 0 0 181>;
 			wakeup-parent = <&pdc>;
 
+			cci0_default: cci0-default {
+				cci0_i2c0_default: cci0-i2c0-default {
+					/* SDA, SCL */
+					pins = "gpio101", "gpio102";
+					function = "cci_i2c";
+
+					bias-pull-up;
+					drive-strength = <2>; /* 2 mA */
+				};
+
+				cci0_i2c1_default: cci0-i2c1-default {
+					/* SDA, SCL */
+					pins = "gpio103", "gpio104";
+					function = "cci_i2c";
+
+					bias-pull-up;
+					drive-strength = <2>; /* 2 mA */
+				};
+			};
+
+			cci0_sleep: cci0-sleep {
+				cci0_i2c0_sleep: cci0-i2c0-sleep {
+					/* SDA, SCL */
+					pins = "gpio101", "gpio102";
+					function = "cci_i2c";
+
+					drive-strength = <2>; /* 2 mA */
+					bias-pull-down;
+				};
+
+				cci0_i2c1_sleep: cci0-i2c1-sleep {
+					/* SDA, SCL */
+					pins = "gpio103", "gpio104";
+					function = "cci_i2c";
+
+					drive-strength = <2>; /* 2 mA */
+					bias-pull-down;
+				};
+			};
+
+			cci1_default: cci1-default {
+				cci1_i2c0_default: cci1-i2c0-default {
+					/* SDA, SCL */
+					pins = "gpio105","gpio106";
+					function = "cci_i2c";
+
+					bias-pull-up;
+					drive-strength = <2>; /* 2 mA */
+				};
+
+				cci1_i2c1_default: cci1-i2c1-default {
+					/* SDA, SCL */
+					pins = "gpio107","gpio108";
+					function = "cci_i2c";
+
+					bias-pull-up;
+					drive-strength = <2>; /* 2 mA */
+				};
+			};
+
+			cci1_sleep: cci1-sleep {
+				cci1_i2c0_sleep: cci1-i2c0-sleep {
+					/* SDA, SCL */
+					pins = "gpio105","gpio106";
+					function = "cci_i2c";
+
+					bias-pull-down;
+					drive-strength = <2>; /* 2 mA */
+				};
+
+				cci1_i2c1_sleep: cci1-i2c1-sleep {
+					/* SDA, SCL */
+					pins = "gpio107","gpio108";
+					function = "cci_i2c";
+
+					bias-pull-down;
+					drive-strength = <2>; /* 2 mA */
+				};
+			};
+
 			pri_mi2s_active: pri-mi2s-active {
 				sclk {
 					pins = "gpio138";
@@ -3850,7 +4786,7 @@
 				apr {
 					compatible = "qcom,apr-v2";
 					qcom,glink-channels = "apr_audio_svc";
-					qcom,apr-domain = <APR_DOMAIN_ADSP>;
+					qcom,domain = <APR_DOMAIN_ADSP>;
 					#address-cells = <1>;
 					#size-cells = <0>;
 
@@ -3905,6 +4841,7 @@
 					compatible = "qcom,fastrpc";
 					qcom,glink-channels = "fastrpcglink-apps-dsp";
 					label = "adsp";
+					qcom,non-secure-domain;
 					#address-cells = <1>;
 					#size-cells = <0>;
 
@@ -3946,9 +4883,9 @@
 		};
 
 		timer@17c20000 {
-			#address-cells = <2>;
-			#size-cells = <2>;
-			ranges;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0 0 0x20000000>;
 			compatible = "arm,armv7-timer-mem";
 			reg = <0x0 0x17c20000 0x0 0x1000>;
 			clock-frequency = <19200000>;
@@ -3957,49 +4894,49 @@
 				frame-number = <0>;
 				interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
 					     <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0x0 0x17c21000 0x0 0x1000>,
-				      <0x0 0x17c22000 0x0 0x1000>;
+				reg = <0x17c21000 0x1000>,
+				      <0x17c22000 0x1000>;
 			};
 
 			frame@17c23000 {
 				frame-number = <1>;
 				interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0x0 0x17c23000 0x0 0x1000>;
+				reg = <0x17c23000 0x1000>;
 				status = "disabled";
 			};
 
 			frame@17c25000 {
 				frame-number = <2>;
 				interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0x0 0x17c25000 0x0 0x1000>;
+				reg = <0x17c25000 0x1000>;
 				status = "disabled";
 			};
 
 			frame@17c27000 {
 				frame-number = <3>;
 				interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0x0 0x17c27000 0x0 0x1000>;
+				reg = <0x17c27000 0x1000>;
 				status = "disabled";
 			};
 
 			frame@17c29000 {
 				frame-number = <4>;
 				interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0x0 0x17c29000 0x0 0x1000>;
+				reg = <0x17c29000 0x1000>;
 				status = "disabled";
 			};
 
 			frame@17c2b000 {
 				frame-number = <5>;
 				interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0x0 0x17c2b000 0x0 0x1000>;
+				reg = <0x17c2b000 0x1000>;
 				status = "disabled";
 			};
 
 			frame@17c2d000 {
 				frame-number = <6>;
 				interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0x0 0x17c2d000 0x0 0x1000>;
+				reg = <0x17c2d000 0x1000>;
 				status = "disabled";
 			};
 		};
@@ -4076,7 +5013,7 @@
 				};
 			};
 
-			apps_bcm_voter: bcm_voter {
+			apps_bcm_voter: bcm-voter {
 				compatible = "qcom,bcm-voter";
 			};
 		};
@@ -4101,7 +5038,10 @@
 
 			clocks = <&rpmhcc RPMH_CXO_CLK>, <&gcc GPLL0>;
 			clock-names = "xo", "alternate";
-
+			interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "dcvsh-irq-0", "dcvsh-irq-1", "dcvsh-irq-2";
 			#freq-domain-cells = <1>;
 		};
 	};
@@ -4702,7 +5642,7 @@
 			};
 		};
 
-		gpu-thermal-top {
+		gpu-top-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 
@@ -4837,7 +5777,7 @@
 			};
 		};
 
-		gpu-thermal-bottom {
+		gpu-bottom-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 
diff --git a/arch/arm64/boot/dts/qcom/sm8350-hdk.dts b/arch/arm64/boot/dts/qcom/sm8350-hdk.dts
index be062377c936..0fcf5bd88fc7 100644
--- a/arch/arm64/boot/dts/qcom/sm8350-hdk.dts
+++ b/arch/arm64/boot/dts/qcom/sm8350-hdk.dts
@@ -5,7 +5,6 @@
 
 /dts-v1/;
 
-#include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
 #include "sm8350.dtsi"
 
@@ -214,6 +213,10 @@
 	firmware-name = "qcom/sm8350/cdsp.mbn";
 };
 
+&gpi_dma1 {
+	status = "okay";
+};
+
 &mpss {
 	status = "okay";
 	firmware-name = "qcom/sm8350/modem.mbn";
diff --git a/arch/arm64/boot/dts/qcom/sm8350-microsoft-surface-duo2.dts b/arch/arm64/boot/dts/qcom/sm8350-microsoft-surface-duo2.dts
new file mode 100644
index 000000000000..9c4cfd995ff2
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sm8350-microsoft-surface-duo2.dts
@@ -0,0 +1,379 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (C) 2021, Microsoft Corporation
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+#include "sm8350.dtsi"
+#include "pm8350.dtsi"
+#include "pm8350b.dtsi"
+#include "pm8350c.dtsi"
+#include "pmk8350.dtsi"
+#include "pmr735a.dtsi"
+#include "pmr735b.dtsi"
+
+/ {
+	model = "Microsoft Surface Duo 2";
+	compatible = "microsoft,surface-duo2", "qcom,sm8350";
+	chassis-type = "handset";
+
+	aliases {
+		serial0 = &uart2;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	vph_pwr: vph-pwr-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vph_pwr";
+		regulator-min-microvolt = <3700000>;
+		regulator-max-microvolt = <3700000>;
+
+		regulator-always-on;
+		regulator-boot-on;
+	};
+};
+
+&adsp {
+	status = "okay";
+	firmware-name = "qcom/sm8350/microsoft/adsp.mbn";
+};
+
+&apps_rsc {
+	pm8350-rpmh-regulators {
+		compatible = "qcom,pm8350-rpmh-regulators";
+		qcom,pmic-id = "b";
+
+		vdd-s1-supply = <&vph_pwr>;
+		vdd-s2-supply = <&vph_pwr>;
+		vdd-s3-supply = <&vph_pwr>;
+		vdd-s4-supply = <&vph_pwr>;
+		vdd-s5-supply = <&vph_pwr>;
+		vdd-s6-supply = <&vph_pwr>;
+		vdd-s7-supply = <&vph_pwr>;
+		vdd-s8-supply = <&vph_pwr>;
+		vdd-s9-supply = <&vph_pwr>;
+		vdd-s10-supply = <&vph_pwr>;
+		vdd-s11-supply = <&vph_pwr>;
+		vdd-s12-supply = <&vph_pwr>;
+
+		vdd-l1-l4-supply = <&vreg_s11b_0p95>;
+		vdd-l2-l7-supply = <&vreg_bob>;
+		vdd-l3-l5-supply = <&vreg_bob>;
+		vdd-l6-l9-l10-supply = <&vreg_s11b_0p95>;
+		vdd-l8-supply = <&vreg_s2c_0p8>;
+
+		vreg_s10b_1p8: smps10 {
+			regulator-name = "vreg_s10b_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		vreg_s11b_0p95: smps11 {
+			regulator-name = "vreg_s11b_0p95";
+			regulator-min-microvolt = <752000>;
+			regulator-max-microvolt = <1000000>;
+		};
+
+		vreg_s12b_1p25: smps12 {
+			regulator-name = "vreg_s12b_1p25";
+			regulator-min-microvolt = <1224000>;
+			regulator-max-microvolt = <1360000>;
+		};
+
+		vreg_l1b_0p88: ldo1 {
+			regulator-name = "vreg_l1b_0p88";
+			regulator-min-microvolt = <912000>;
+			regulator-max-microvolt = <920000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2b_3p07: ldo2 {
+			regulator-name = "vreg_l2b_3p07";
+			regulator-min-microvolt = <3072000>;
+			regulator-max-microvolt = <3072000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3b_0p9: ldo3 {
+			regulator-name = "vreg_l3b_0p9";
+			regulator-min-microvolt = <904000>;
+			regulator-max-microvolt = <904000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l5b_0p88: ldo5 {
+			regulator-name = "vreg_l3b_0p9";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <888000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l6b_1p2: ldo6 {
+			regulator-name = "vreg_l6b_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1208000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l7b_2p96: ldo7 {
+			regulator-name = "vreg_l7b_2p96";
+			regulator-min-microvolt = <2400000>;
+			regulator-max-microvolt = <3008000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l9b_1p2: ldo9 {
+			regulator-name = "vreg_l9b_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	pm8350c-rpmh-regulators {
+		compatible = "qcom,pm8350c-rpmh-regulators";
+		qcom,pmic-id = "c";
+
+		vdd-s1-supply = <&vph_pwr>;
+		vdd-s2-supply = <&vph_pwr>;
+		vdd-s3-supply = <&vph_pwr>;
+		vdd-s4-supply = <&vph_pwr>;
+		vdd-s5-supply = <&vph_pwr>;
+		vdd-s6-supply = <&vph_pwr>;
+		vdd-s7-supply = <&vph_pwr>;
+		vdd-s8-supply = <&vph_pwr>;
+		vdd-s9-supply = <&vph_pwr>;
+		vdd-s10-supply = <&vph_pwr>;
+
+		vdd-l1-l12-supply = <&vreg_s1c_1p86>;
+		vdd-l2-l8-supply = <&vreg_s1c_1p86>;
+		vdd-l3-l4-l5-l7-l13-supply = <&vreg_bob>;
+		vdd-l6-l9-l11-supply = <&vreg_bob>;
+		vdd-l10-supply = <&vreg_s12b_1p25>;
+
+		vdd-bob-supply = <&vph_pwr>;
+
+		vreg_s1c_1p86: smps1 {
+			regulator-name = "vreg_s1c_1p86";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1952000>;
+		};
+
+		vreg_s2c_0p8: smps2 {
+			regulator-name = "vreg_s2c_0p8";
+			regulator-min-microvolt = <640000>;
+			regulator-max-microvolt = <1000000>;
+		};
+
+		vreg_s10c_1p05: smps10 {
+			regulator-name = "vreg_s10c_1p05";
+			regulator-min-microvolt = <1048000>;
+			regulator-max-microvolt = <1128000>;
+		};
+
+		vreg_bob: bob {
+			regulator-name = "vreg_bob";
+			regulator-min-microvolt = <3008000>;
+			regulator-max-microvolt = <3960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>;
+		};
+
+		vreg_l1c_1p8: ldo1 {
+			regulator-name = "vreg_l1c_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2c_1p8: ldo2 {
+			regulator-name = "vreg_l2c_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3c_3p0: ldo3 {
+			regulator-name = "vreg_l3c_3p0";
+			regulator-min-microvolt = <3008000>;
+			regulator-max-microvolt = <3008000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l4c_uim1: ldo4 {
+			regulator-name = "vreg_l4c_uim1";
+			regulator-min-microvolt = <1704000>;
+			regulator-max-microvolt = <3000000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l5c_uim2: ldo5 {
+			regulator-name = "vreg_l5c_uim2";
+			regulator-min-microvolt = <1704000>;
+			regulator-max-microvolt = <3000000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l6c_1p8: ldo6 {
+			regulator-name = "vreg_l6c_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l7c_3p0: ldo7 {
+			regulator-name = "vreg_l7c_3p0";
+			regulator-min-microvolt = <3008000>;
+			regulator-max-microvolt = <3008000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l8c_1p8: ldo8 {
+			regulator-name = "vreg_l8c_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l9c_2p96: ldo9 {
+			regulator-name = "vreg_l9c_2p96";
+			regulator-min-microvolt = <2960000>;
+			regulator-max-microvolt = <3008000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l10c_1p2: ldo10 {
+			regulator-name = "vreg_l10c_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l11c_2p96: ldo11 {
+			regulator-name = "vreg_l11c_2p96";
+			regulator-min-microvolt = <2400000>;
+			regulator-max-microvolt = <3008000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l12c_1p8: ldo12 {
+			regulator-name = "vreg_l12c_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2000000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l13c_3p0: ldo13 {
+			regulator-name = "vreg_l13c_3p0";
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+};
+
+&cdsp {
+	status = "okay";
+	firmware-name = "qcom/sm8350/microsoft/cdsp.mbn";
+};
+
+&i2c10 {
+	status = "okay";
+};
+
+&i2c11 {
+	status = "okay";
+};
+
+&ipa {
+	status = "okay";
+
+	memory-region = <&pil_ipa_fw_mem>;
+};
+
+&mpss {
+	status = "okay";
+	firmware-name = "qcom/sm8350/microsoft/modem.mbn";
+};
+
+&qupv3_id_0 {
+	status = "okay";
+};
+
+&qupv3_id_1 {
+	status = "okay";
+};
+
+&slpi {
+	status = "okay";
+	firmware-name = "qcom/sm8350/microsoft/slpi.mbn";
+};
+
+&tlmm {
+	gpio-reserved-ranges = <4 4>, <12 4>, <56 4>, <76 4>;
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&ufs_mem_hc {
+	status = "okay";
+
+	reset-gpios = <&tlmm 203 GPIO_ACTIVE_LOW>;
+
+	vcc-supply = <&vreg_l7b_2p96>;
+	vcc-max-microamp = <800000>;
+	vccq-supply = <&vreg_l9b_1p2>;
+	vccq-max-microamp = <900000>;
+};
+
+&ufs_mem_phy {
+	status = "okay";
+
+	vdda-phy-supply = <&vreg_l5b_0p88>;
+	vdda-pll-supply = <&vreg_l6b_1p2>;
+};
+
+&usb_1 {
+	status = "okay";
+	dr_mode = "peripheral";
+};
+
+&usb_1_hsphy {
+	status = "okay";
+
+	vdda-pll-supply = <&vreg_l5b_0p88>;
+	vdda18-supply = <&vreg_l1c_1p8>;
+	vdda33-supply = <&vreg_l2b_3p07>;
+};
+
+&usb_1_qmpphy {
+	status = "okay";
+
+	vdda-phy-supply = <&vreg_l6b_1p2>;
+	vdda-pll-supply = <&vreg_l1b_0p88>;
+};
+
+&usb_2 {
+	status = "okay";
+};
+
+&usb_2_hsphy {
+	status = "okay";
+
+	vdda-pll-supply = <&vreg_l5b_0p88>;
+	vdda18-supply = <&vreg_l1c_1p8>;
+	vdda33-supply = <&vreg_l2b_3p07>;
+};
+
+&usb_2_qmpphy {
+	status = "okay";
+
+	vdda-phy-supply = <&vreg_l6b_1p2>;
+	vdda-pll-supply = <&vreg_l5b_0p88>;
+};
diff --git a/arch/arm64/boot/dts/qcom/sm8350-mtp.dts b/arch/arm64/boot/dts/qcom/sm8350-mtp.dts
index 06eedbe52c42..52cf3045602f 100644
--- a/arch/arm64/boot/dts/qcom/sm8350-mtp.dts
+++ b/arch/arm64/boot/dts/qcom/sm8350-mtp.dts
@@ -5,7 +5,6 @@
 
 /dts-v1/;
 
-#include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
 #include "sm8350.dtsi"
 #include "pm8350.dtsi"
@@ -290,6 +289,15 @@
 	status = "okay";
 };
 
+&pon_pwrkey {
+	status = "okay";
+};
+
+&pon_resin {
+	status = "okay";
+	linux,code = <KEY_VOLUMEDOWN>;
+};
+
 &qupv3_id_0 {
 	status = "okay";
 };
diff --git a/arch/arm64/boot/dts/qcom/sm8350-sony-xperia-sagami-pdx214.dts b/arch/arm64/boot/dts/qcom/sm8350-sony-xperia-sagami-pdx214.dts
new file mode 100644
index 000000000000..cc650508dc2d
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sm8350-sony-xperia-sagami-pdx214.dts
@@ -0,0 +1,19 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, Konrad Dybcio <konrad.dybcio@somainline.org>
+ */
+
+/dts-v1/;
+
+#include "sm8350-sony-xperia-sagami.dtsi"
+
+/ {
+	model = "Sony Xperia 5 III";
+	compatible = "sony,pdx214-generic", "qcom,sm8350";
+};
+
+&framebuffer {
+	width = <1080>;
+	height = <2520>;
+	stride = <(1080 * 4)>;
+};
diff --git a/arch/arm64/boot/dts/qcom/sm8350-sony-xperia-sagami-pdx215.dts b/arch/arm64/boot/dts/qcom/sm8350-sony-xperia-sagami-pdx215.dts
new file mode 100644
index 000000000000..d21bbeb603a6
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sm8350-sony-xperia-sagami-pdx215.dts
@@ -0,0 +1,13 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, Konrad Dybcio <konrad.dybcio@somainline.org>
+ */
+
+/dts-v1/;
+
+#include "sm8350-sony-xperia-sagami.dtsi"
+
+/ {
+	model = "Sony Xperia 1 III";
+	compatible = "sony,pdx215-generic", "qcom,sm8350";
+};
diff --git a/arch/arm64/boot/dts/qcom/sm8350-sony-xperia-sagami.dtsi b/arch/arm64/boot/dts/qcom/sm8350-sony-xperia-sagami.dtsi
new file mode 100644
index 000000000000..b3c9952ac173
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sm8350-sony-xperia-sagami.dtsi
@@ -0,0 +1,259 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, Konrad Dybcio <konrad.dybcio@somainline.org>
+ */
+
+#include "sm8350.dtsi"
+#include "pm8350.dtsi"
+#include "pm8350b.dtsi"
+#include "pm8350c.dtsi"
+#include "pmk8350.dtsi"
+#include "pmr735a.dtsi"
+#include "pmr735b.dtsi"
+
+/ {
+	/*
+	 * Yes, you are correct, there is NO MORE {msm,board,pmic}-id on SM8350!
+	 * Adding it will cause the bootloader to go crazy and randomly crash
+	 * shortly after closing UEFI boot services.. Perhaps that has something
+	 * to do with the OS running inside a VM now..?
+	 */
+
+	chassis-type = "handset";
+
+	chosen {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		framebuffer: framebuffer@e1000000 {
+			compatible = "simple-framebuffer";
+			reg = <0 0xe1000000 0 0x2300000>;
+
+			/* The display, even though it's 4K, initializes at 1080-ish p */
+			width = <1096>;
+			height = <2560>;
+			stride = <(1096 * 4)>;
+			format = "a8r8g8b8";
+			/*
+			 * That's (going to be) a lot of clocks, but it's necessary due
+			 * to unused clk cleanup & no panel driver yet
+			 */
+			clocks = <&gcc GCC_DISP_HF_AXI_CLK>,
+				 <&gcc GCC_DISP_SF_AXI_CLK>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		/* For reasons still unknown, GAssist key and Camera Focus/Shutter don't work.. */
+
+		key-vol-down {
+			label = "Volume Down";
+			linux,code = <KEY_VOLUMEDOWN>;
+			gpios = <&pmk8350_gpios 3 GPIO_ACTIVE_LOW>;
+			debounce-interval = <15>;
+			linux,can-disable;
+			gpio-key,wakeup;
+		};
+	};
+
+	reserved-memory {
+		cont_splash_mem: memory@e1000000 {
+			reg = <0 0xe1000000 0 0x2300000>;
+			no-map;
+		};
+
+		ramoops@ffc00000 {
+			compatible = "ramoops";
+			reg = <0 0xffc00000 0 0x100000>;
+			console-size = <0x40000>;
+			record-size = <0x1000>;
+			no-map;
+		};
+	};
+};
+
+&adsp {
+	status = "okay";
+	firmware-name = "qcom/adsp.mbn";
+};
+
+&cdsp {
+	status = "okay";
+	firmware-name = "qcom/cdsp.mbn";
+};
+
+&i2c1 {
+	status = "okay";
+	clock-frequency = <1000000>;
+
+	/* Some subset of SONY IMX663 camera sensor @ 38 */
+};
+
+&i2c2 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	/* Richwave RTC6226 FM Radio Receiver @ 64 */
+};
+
+&i2c4 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	/* Samsung Touchscreen (needs I2C GPI DMA) @ 48 */
+};
+
+&i2c11 {
+	status = "okay";
+	clock-frequency = <1000000>;
+
+	cs35l41_l: cs35l41@40 {
+		compatible = "cirrus,cs35l41";
+		reg = <0x40>;
+		interrupt-parent = <&tlmm>;
+		interrupts = <36 IRQ_TYPE_LEVEL_LOW>;
+		reset-gpios = <&tlmm 37 GPIO_ACTIVE_HIGH>;
+		cirrus,boost-peak-milliamp = <4000>;
+		cirrus,boost-ind-nanohenry = <1000>;
+		cirrus,boost-cap-microfarad = <15>;
+		cirrus,asp-sdout-hiz = <3>;
+		cirrus,gpio2-src-select = <2>;
+		cirrus,gpio2-output-enable;
+		#sound-dai-cells = <1>;
+	};
+
+	cs35l41_r: cs35l41@41 {
+		compatible = "cirrus,cs35l41";
+		reg = <0x41>;
+		interrupt-parent = <&tlmm>;
+		interrupts = <36 IRQ_TYPE_LEVEL_LOW>;
+		reset-gpios = <&tlmm 37 GPIO_ACTIVE_HIGH>;
+		cirrus,boost-peak-milliamp = <4000>;
+		cirrus,boost-ind-nanohenry = <1000>;
+		cirrus,boost-cap-microfarad = <15>;
+		cirrus,asp-sdout-hiz = <3>;
+		cirrus,gpio2-src-select = <2>;
+		cirrus,gpio2-output-enable;
+		#sound-dai-cells = <1>;
+	};
+};
+
+&i2c12 {
+	status = "okay";
+	/* Clock frequency was not specified downstream, let's park it to 100 KHz */
+	clock-frequency = <100000>;
+
+	/* AMS TCS3490 RGB+IR color sensor @ 72 */
+};
+
+&i2c13 {
+	status = "okay";
+	/* Clock frequency was not specified downstream, let's park it to 100 KHz */
+	clock-frequency = <100000>;
+
+	/* Qualcomm PM8008i/PM8008j (?) @ 8, 9, c, d */
+	/* Dialog SLG51000 CMIC @ 75 */
+};
+
+&i2c15 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	/* NXP SN1X0 NFC @ 28 */
+};
+
+&i2c17 {
+	status = "okay";
+	clock-frequency = <1000000>;
+
+	/* Cirrus Logic CS40L25A boosted haptics driver @ 40 */
+};
+
+&ipa {
+	status = "okay";
+	memory-region = <&pil_ipa_fw_mem>;
+	firmware-name = "qcom/ipa_fws.mbn";
+};
+
+&mpss {
+	status = "okay";
+	firmware-name = "qcom/modem.mbn";
+};
+
+&pmk8350_rtc {
+	status = "okay";
+};
+
+&pon_pwrkey {
+	status = "okay";
+};
+
+&pon_resin {
+	status = "okay";
+	linux,code = <KEY_VOLUMEUP>;
+};
+
+&qupv3_id_0 {
+	status = "okay";
+};
+
+&qupv3_id_1 {
+	status = "okay";
+};
+
+&qupv3_id_2 {
+	status = "okay";
+};
+
+&slpi {
+	status = "okay";
+	firmware-name = "qcom/slpi.mbn";
+};
+
+&spi14 {
+	status = "okay";
+
+	/* NXP SN1X0 NFC Secure Element @ 0 */
+};
+
+&tlmm {
+	gpio-reserved-ranges = <44 4>;
+
+	ts_int_default: ts-int-default-state {
+		pins = "gpio23";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+		input-enable;
+	};
+};
+
+/* BIG WARNING! DO NOT TOUCH UFS, YOUR DEVICE WILL DIE! */
+&ufs_mem_hc { status = "disabled"; };
+&ufs_mem_phy { status = "disabled"; };
+
+/* TODO: Make USB3 work (perhaps needs regulators for higher-current operation?) */
+&usb_1 {
+	status = "okay";
+
+	qcom,select-utmi-as-pipe-clk;
+};
+
+&usb_1_dwc3 {
+	dr_mode = "peripheral";
+
+	maximum-speed = "high-speed";
+	phys = <&usb_1_hsphy>;
+	phy-names = "usb2-phy";
+};
+
+&usb_1_hsphy {
+	status = "okay";
+};
+
+&usb_1_qmpphy {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/qcom/sm8350.dtsi b/arch/arm64/boot/dts/qcom/sm8350.dtsi
index d134280e2939..a86d9ea93b9d 100644
--- a/arch/arm64/boot/dts/qcom/sm8350.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8350.dtsi
@@ -4,8 +4,11 @@
  */
 
 #include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/qcom,dispcc-sm8350.h>
 #include <dt-bindings/clock/qcom,gcc-sm8350.h>
 #include <dt-bindings/clock/qcom,rpmh.h>
+#include <dt-bindings/dma/qcom-gpi.h>
+#include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/interconnect/qcom,sm8350.h>
 #include <dt-bindings/mailbox/qcom-ipcc.h>
 #include <dt-bindings/power/qcom-rpmpd.h>
@@ -34,6 +37,24 @@
 			clock-frequency = <32000>;
 			#clock-cells = <0>;
 		};
+
+		ufs_phy_rx_symbol_0_clk: ufs-phy-rx-symbol-0 {
+			compatible = "fixed-clock";
+			clock-frequency = <1000>;
+			#clock-cells = <0>;
+		};
+
+		ufs_phy_rx_symbol_1_clk: ufs-phy-rx-symbol-1 {
+			compatible = "fixed-clock";
+			clock-frequency = <1000>;
+			#clock-cells = <0>;
+		};
+
+		ufs_phy_tx_symbol_0_clk: ufs-phy-tx-symbol-0 {
+			compatible = "fixed-clock";
+			clock-frequency = <1000>;
+			#clock-cells = <0>;
+		};
 	};
 
 	cpus {
@@ -321,6 +342,44 @@
 		};
 	};
 
+	qup_opp_table_100mhz: opp-table-qup100mhz {
+		compatible = "operating-points-v2";
+
+		opp-50000000 {
+			opp-hz = /bits/ 64 <50000000>;
+			required-opps = <&rpmhpd_opp_min_svs>;
+		};
+
+		opp-75000000 {
+			opp-hz = /bits/ 64 <75000000>;
+			required-opps = <&rpmhpd_opp_low_svs>;
+		};
+
+		opp-100000000 {
+			opp-hz = /bits/ 64 <100000000>;
+			required-opps = <&rpmhpd_opp_svs>;
+		};
+	};
+
+	qup_opp_table_120mhz: opp-table-qup120mhz {
+		compatible = "operating-points-v2";
+
+		opp-50000000 {
+			opp-hz = /bits/ 64 <50000000>;
+			required-opps = <&rpmhpd_opp_min_svs>;
+		};
+
+		opp-75000000 {
+			opp-hz = /bits/ 64 <75000000>;
+			required-opps = <&rpmhpd_opp_low_svs>;
+		};
+
+		opp-120000000 {
+			opp-hz = /bits/ 64 <120000000>;
+			required-opps = <&rpmhpd_opp_svs>;
+		};
+	};
+
 	reserved_memory: reserved-memory {
 		#address-cells = <2>;
 		#size-cells = <2>;
@@ -583,8 +642,30 @@
 			#clock-cells = <1>;
 			#reset-cells = <1>;
 			#power-domain-cells = <1>;
-			clock-names = "bi_tcxo", "sleep_clk";
-			clocks = <&rpmhcc RPMH_CXO_CLK>, <&sleep_clk>;
+			clock-names = "bi_tcxo",
+				      "sleep_clk",
+				      "pcie_0_pipe_clk",
+				      "pcie_1_pipe_clk",
+				      "ufs_card_rx_symbol_0_clk",
+				      "ufs_card_rx_symbol_1_clk",
+				      "ufs_card_tx_symbol_0_clk",
+				      "ufs_phy_rx_symbol_0_clk",
+				      "ufs_phy_rx_symbol_1_clk",
+				      "ufs_phy_tx_symbol_0_clk",
+				      "usb3_phy_wrapper_gcc_usb30_pipe_clk",
+				      "usb3_uni_phy_sec_gcc_usb30_pipe_clk";
+			clocks = <&rpmhcc RPMH_CXO_CLK>,
+				 <&sleep_clk>,
+				 <0>,
+				 <0>,
+				 <0>,
+				 <0>,
+				 <0>,
+				 <&ufs_phy_rx_symbol_0_clk>,
+				 <&ufs_phy_rx_symbol_1_clk>,
+				 <&ufs_phy_tx_symbol_0_clk>,
+				 <0>,
+				 <0>;
 		};
 
 		ipcc: mailbox@408000 {
@@ -596,17 +677,362 @@
 			#mbox-cells = <2>;
 		};
 
+		gpi_dma2: dma-controller@800000 {
+			compatible = "qcom,sm8350-gpi-dma";
+			reg = <0 0x00800000 0 0x60000>;
+			interrupts = <GIC_SPI 588 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 589 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 590 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 591 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 592 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 593 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 594 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 595 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 596 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 597 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 598 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 599 IRQ_TYPE_LEVEL_HIGH>;
+			dma-channels = <12>;
+			dma-channel-mask = <0xff>;
+			iommus = <&apps_smmu 0x5f6 0x0>;
+			#dma-cells = <3>;
+			status = "disabled";
+		};
+
+		qupv3_id_2: geniqup@8c0000 {
+			compatible = "qcom,geni-se-qup";
+			reg = <0x0 0x008c0000 0x0 0x6000>;
+			clock-names = "m-ahb", "s-ahb";
+			clocks = <&gcc GCC_QUPV3_WRAP_2_M_AHB_CLK>,
+				 <&gcc GCC_QUPV3_WRAP_2_S_AHB_CLK>;
+			iommus = <&apps_smmu 0x5e3 0x0>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+			status = "disabled";
+
+			i2c14: i2c@880000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00880000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP2_S0_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c14_default>;
+				interrupts = <GIC_SPI 373 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&gpi_dma2 0 0 QCOM_GPI_I2C>,
+				       <&gpi_dma2 1 0 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			spi14: spi@880000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00880000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP2_S0_CLK>;
+				interrupts = <GIC_SPI 373 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SM8350_CX>;
+				operating-points-v2 = <&qup_opp_table_120mhz>;
+				dmas = <&gpi_dma2 0 0 QCOM_GPI_SPI>,
+				       <&gpi_dma2 1 0 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			i2c15: i2c@884000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00884000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP2_S1_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c15_default>;
+				interrupts = <GIC_SPI 583 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&gpi_dma2 0 1 QCOM_GPI_I2C>,
+				       <&gpi_dma2 1 1 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			spi15: spi@884000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00884000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP2_S1_CLK>;
+				interrupts = <GIC_SPI 583 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SM8350_CX>;
+				operating-points-v2 = <&qup_opp_table_120mhz>;
+				dmas = <&gpi_dma2 0 1 QCOM_GPI_SPI>,
+				       <&gpi_dma2 1 1 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			i2c16: i2c@888000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00888000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP2_S2_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c16_default>;
+				interrupts = <GIC_SPI 584 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&gpi_dma2 0 2 QCOM_GPI_I2C>,
+				       <&gpi_dma2 1 2 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			spi16: spi@888000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00888000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP2_S2_CLK>;
+				interrupts = <GIC_SPI 584 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SM8350_CX>;
+				operating-points-v2 = <&qup_opp_table_100mhz>;
+				dmas = <&gpi_dma2 0 2 QCOM_GPI_SPI>,
+				       <&gpi_dma2 1 2 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			i2c17: i2c@88c000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x0088c000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP2_S3_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c17_default>;
+				interrupts = <GIC_SPI 585 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&gpi_dma2 0 3 QCOM_GPI_I2C>,
+				       <&gpi_dma2 1 3 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			spi17: spi@88c000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x0088c000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP2_S3_CLK>;
+				interrupts = <GIC_SPI 585 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SM8350_CX>;
+				operating-points-v2 = <&qup_opp_table_100mhz>;
+				dmas = <&gpi_dma2 0 3 QCOM_GPI_SPI>,
+				       <&gpi_dma2 1 3 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			/* QUP no. 18 seems to be strictly SPI/UART-only */
+
+			spi18: spi@890000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00890000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP2_S4_CLK>;
+				interrupts = <GIC_SPI 586 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SM8350_CX>;
+				operating-points-v2 = <&qup_opp_table_100mhz>;
+				dmas = <&gpi_dma2 0 4 QCOM_GPI_SPI>,
+				       <&gpi_dma2 1 4 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			uart18: serial@890000 {
+				compatible = "qcom,geni-uart";
+				reg = <0 0x00890000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP2_S4_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_uart18_default>;
+				interrupts = <GIC_SPI 586 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SM8350_CX>;
+				operating-points-v2 = <&qup_opp_table_100mhz>;
+				status = "disabled";
+			};
+
+			i2c19: i2c@894000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00894000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP2_S5_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c19_default>;
+				interrupts = <GIC_SPI 587 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&gpi_dma2 0 5 QCOM_GPI_I2C>,
+				       <&gpi_dma2 1 5 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			spi19: spi@894000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00894000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP2_S5_CLK>;
+				interrupts = <GIC_SPI 587 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SM8350_CX>;
+				operating-points-v2 = <&qup_opp_table_100mhz>;
+				dmas = <&gpi_dma2 0 5 QCOM_GPI_SPI>,
+				       <&gpi_dma2 1 5 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+		};
+
+		gpi_dma0: dma-controller@900000 {
+			compatible = "qcom,sm8350-gpi-dma";
+			reg = <0 0x09800000 0 0x60000>;
+			interrupts = <GIC_SPI 244 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 245 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 246 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 247 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 248 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 249 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 250 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 251 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 252 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 253 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 254 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 255 IRQ_TYPE_LEVEL_HIGH>;
+			dma-channels = <12>;
+			dma-channel-mask = <0x7e>;
+			iommus = <&apps_smmu 0x5b6 0x0>;
+			#dma-cells = <3>;
+			status = "disabled";
+		};
+
 		qupv3_id_0: geniqup@9c0000 {
 			compatible = "qcom,geni-se-qup";
 			reg = <0x0 0x009c0000 0x0 0x6000>;
 			clock-names = "m-ahb", "s-ahb";
 			clocks = <&gcc GCC_QUPV3_WRAP_0_M_AHB_CLK>,
 				 <&gcc GCC_QUPV3_WRAP_0_S_AHB_CLK>;
+			iommus = <&apps_smmu 0x5a3 0>;
 			#address-cells = <2>;
 			#size-cells = <2>;
 			ranges;
 			status = "disabled";
 
+			i2c0: i2c@980000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00980000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c0_default>;
+				interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&gpi_dma0 0 0 QCOM_GPI_I2C>,
+				       <&gpi_dma0 1 0 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			spi0: spi@980000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00980000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
+				interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SM8350_CX>;
+				operating-points-v2 = <&qup_opp_table_100mhz>;
+				dmas = <&gpi_dma0 0 0 QCOM_GPI_SPI>,
+				       <&gpi_dma0 1 0 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			i2c1: i2c@984000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00984000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c1_default>;
+				interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&gpi_dma0 0 1 QCOM_GPI_I2C>,
+				       <&gpi_dma0 1 1 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			spi1: spi@984000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00984000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
+				interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SM8350_CX>;
+				operating-points-v2 = <&qup_opp_table_100mhz>;
+				dmas = <&gpi_dma0 0 1 QCOM_GPI_SPI>,
+				       <&gpi_dma0 1 1 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			i2c2: i2c@988000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00988000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c2_default>;
+				interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&gpi_dma0 0 2 QCOM_GPI_I2C>,
+				       <&gpi_dma0 1 2 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			spi2: spi@988000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00988000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
+				interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SM8350_CX>;
+				operating-points-v2 = <&qup_opp_table_100mhz>;
+				dmas = <&gpi_dma0 0 2 QCOM_GPI_SPI>,
+				       <&gpi_dma0 1 2 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
 			uart2: serial@98c000 {
 				compatible = "qcom,geni-debug-uart";
 				reg = <0 0x0098c000 0 0x4000>;
@@ -615,10 +1041,193 @@
 				pinctrl-names = "default";
 				pinctrl-0 = <&qup_uart3_default_state>;
 				interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SM8350_CX>;
+				operating-points-v2 = <&qup_opp_table_100mhz>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			/* QUP no. 3 seems to be strictly SPI-only */
+
+			spi3: spi@98c000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x0098c000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
+				interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SM8350_CX>;
+				operating-points-v2 = <&qup_opp_table_100mhz>;
+				dmas = <&gpi_dma0 0 3 QCOM_GPI_SPI>,
+				       <&gpi_dma0 1 3 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			i2c4: i2c@990000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00990000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c4_default>;
+				interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&gpi_dma0 0 4 QCOM_GPI_I2C>,
+				       <&gpi_dma0 1 4 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			spi4: spi@990000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00990000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
+				interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SM8350_CX>;
+				operating-points-v2 = <&qup_opp_table_100mhz>;
+				dmas = <&gpi_dma0 0 4 QCOM_GPI_SPI>,
+				       <&gpi_dma0 1 4 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
 				#address-cells = <1>;
 				#size-cells = <0>;
 				status = "disabled";
 			};
+
+			i2c5: i2c@994000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00994000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c5_default>;
+				interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&gpi_dma0 0 5 QCOM_GPI_I2C>,
+				       <&gpi_dma0 1 5 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			spi5: spi@994000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00994000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
+				interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SM8350_CX>;
+				operating-points-v2 = <&qup_opp_table_100mhz>;
+				dmas = <&gpi_dma0 0 5 QCOM_GPI_SPI>,
+				       <&gpi_dma0 1 5 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			i2c6: i2c@998000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00998000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c6_default>;
+				interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&gpi_dma0 0 6 QCOM_GPI_I2C>,
+				       <&gpi_dma0 1 6 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			spi6: spi@998000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00998000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>;
+				interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SM8350_CX>;
+				operating-points-v2 = <&qup_opp_table_100mhz>;
+				dmas = <&gpi_dma0 0 6 QCOM_GPI_SPI>,
+				       <&gpi_dma0 1 6 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			uart6: serial@998000 {
+				compatible = "qcom,geni-uart";
+				reg = <0 0x00998000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_uart6_default>;
+				interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SM8350_CX>;
+				operating-points-v2 = <&qup_opp_table_100mhz>;
+				status = "disabled";
+			};
+
+			i2c7: i2c@99c000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x0099c000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c7_default>;
+				interrupts = <GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&gpi_dma0 0 7 QCOM_GPI_I2C>,
+				       <&gpi_dma0 1 7 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			spi7: spi@99c000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x0099c000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>;
+				interrupts = <GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SM8350_CX>;
+				operating-points-v2 = <&qup_opp_table_100mhz>;
+				dmas = <&gpi_dma0 0 7 QCOM_GPI_SPI>,
+				       <&gpi_dma0 1 7 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+		};
+
+		gpi_dma1: dma-controller@a00000 {
+			compatible = "qcom,sm8350-gpi-dma";
+			reg = <0 0x00a00000 0 0x60000>;
+			interrupts = <GIC_SPI 279 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 280 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 281 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 282 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 283 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 284 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 293 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 294 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 295 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 296 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 297 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 298 IRQ_TYPE_LEVEL_HIGH>;
+			dma-channels = <12>;
+			dma-channel-mask = <0xff>;
+			iommus = <&apps_smmu 0x56 0x0>;
+			#dma-cells = <3>;
+			status = "disabled";
 		};
 
 		qupv3_id_1: geniqup@ac0000 {
@@ -627,19 +1236,199 @@
 			clock-names = "m-ahb", "s-ahb";
 			clocks = <&gcc GCC_QUPV3_WRAP_1_M_AHB_CLK>,
 				 <&gcc GCC_QUPV3_WRAP_1_S_AHB_CLK>;
+			iommus = <&apps_smmu 0x43 0>;
 			#address-cells = <2>;
 			#size-cells = <2>;
 			ranges;
 			status = "disabled";
 
+			i2c8: i2c@a80000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00a80000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c8_default>;
+				interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&gpi_dma1 0 0 QCOM_GPI_I2C>,
+				       <&gpi_dma1 1 0 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			spi8: spi@a80000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00a80000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
+				interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SM8350_CX>;
+				operating-points-v2 = <&qup_opp_table_120mhz>;
+				dmas = <&gpi_dma1 0 0 QCOM_GPI_SPI>,
+				       <&gpi_dma1 1 0 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			i2c9: i2c@a84000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00a84000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c9_default>;
+				interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&gpi_dma1 0 1 QCOM_GPI_I2C>,
+				       <&gpi_dma1 1 1 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			spi9: spi@a84000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00a84000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
+				interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SM8350_CX>;
+				operating-points-v2 = <&qup_opp_table_100mhz>;
+				dmas = <&gpi_dma1 0 1 QCOM_GPI_SPI>,
+				       <&gpi_dma1 1 1 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			i2c10: i2c@a88000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00a88000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c10_default>;
+				interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&gpi_dma1 0 2 QCOM_GPI_I2C>,
+				       <&gpi_dma1 1 2 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			spi10: spi@a88000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00a88000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
+				interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SM8350_CX>;
+				operating-points-v2 = <&qup_opp_table_100mhz>;
+				dmas = <&gpi_dma1 0 2 QCOM_GPI_SPI>,
+				       <&gpi_dma1 1 2 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			i2c11: i2c@a8c000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00a8c000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c11_default>;
+				interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&gpi_dma1 0 3 QCOM_GPI_I2C>,
+				       <&gpi_dma1 1 3 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			spi11: spi@a8c000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00a8c000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
+				interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SM8350_CX>;
+				operating-points-v2 = <&qup_opp_table_100mhz>;
+				dmas = <&gpi_dma1 0 3 QCOM_GPI_SPI>,
+				       <&gpi_dma1 1 3 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			i2c12: i2c@a90000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00a90000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c12_default>;
+				interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&gpi_dma1 0 4 QCOM_GPI_I2C>,
+				       <&gpi_dma1 1 4 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			spi12: spi@a90000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00a90000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
+				interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SM8350_CX>;
+				operating-points-v2 = <&qup_opp_table_100mhz>;
+				dmas = <&gpi_dma1 0 4 QCOM_GPI_SPI>,
+				       <&gpi_dma1 1 4 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
 			i2c13: i2c@a94000 {
 				compatible = "qcom,geni-i2c";
 				reg = <0 0x00a94000 0 0x4000>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
 				pinctrl-names = "default";
-				pinctrl-0 = <&qup_i2c13_default_state>;
+				pinctrl-0 = <&qup_i2c13_default>;
+				interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
+				dmas = <&gpi_dma1 0 5 QCOM_GPI_I2C>,
+				       <&gpi_dma1 1 5 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			spi13: spi@a94000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00a94000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
 				interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
+				power-domains = <&rpmhpd SM8350_CX>;
+				operating-points-v2 = <&qup_opp_table_100mhz>;
+				dmas = <&gpi_dma1 0 5 QCOM_GPI_SPI>,
+				       <&gpi_dma1 1 5 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
 				#address-cells = <1>;
 				#size-cells = <0>;
 				status = "disabled";
@@ -836,6 +1625,8 @@
 			interconnect-names = "memory",
 					     "config";
 
+			qcom,qmp = <&aoss_qmp>;
+
 			qcom,smem-states = <&ipa_smp2p_out 0>,
 					   <&ipa_smp2p_out 1>;
 			qcom,smem-state-names = "ipa-clock-enabled-valid",
@@ -866,8 +1657,8 @@
 			clocks = <&rpmhcc RPMH_CXO_CLK>;
 			clock-names = "xo";
 
-			power-domains = <&rpmhpd 0>,
-					<&rpmhpd 12>;
+			power-domains = <&rpmhpd SM8350_CX>,
+					<&rpmhpd SM8350_MSS>;
 			power-domain-names = "cx", "mss";
 
 			interconnects = <&mc_virt MASTER_LLCC &mc_virt SLAVE_EBI1>;
@@ -887,7 +1678,6 @@
 							     IRQ_TYPE_EDGE_RISING>;
 				mboxes = <&ipcc IPCC_CLIENT_MPSS
 						IPCC_MPROC_SIGNAL_GLINK_QMP>;
-				interrupts = <GIC_SPI 449 IRQ_TYPE_EDGE_RISING>;
 				label = "modem";
 				qcom,remote-pid = <1>;
 			};
@@ -910,7 +1700,7 @@
 			reg = <0 0x0c263000 0 0x1ff>, /* TM */
 			      <0 0x0c222000 0 0x8>; /* SROT */
 			#qcom,sensors = <15>;
-			interrupts = <&pdc 26 IRQ_TYPE_LEVEL_HIGH>,
+			interrupts-extended = <&pdc 26 IRQ_TYPE_LEVEL_HIGH>,
 				     <&pdc 28 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "uplow", "critical";
 			#thermal-sensor-cells = <1>;
@@ -921,14 +1711,14 @@
 			reg = <0 0x0c265000 0 0x1ff>, /* TM */
 			      <0 0x0c223000 0 0x8>; /* SROT */
 			#qcom,sensors = <14>;
-			interrupts = <&pdc 27 IRQ_TYPE_LEVEL_HIGH>,
+			interrupts-extended = <&pdc 27 IRQ_TYPE_LEVEL_HIGH>,
 				     <&pdc 29 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "uplow", "critical";
 			#thermal-sensor-cells = <1>;
 		};
 
 		aoss_qmp: power-controller@c300000 {
-			compatible = "qcom,sm8350-aoss-qmp";
+			compatible = "qcom,sm8350-aoss-qmp", "qcom,aoss-qmp";
 			reg = <0 0x0c300000 0 0x400>;
 			interrupts-extended = <&ipcc IPCC_CLIENT_AOP IPCC_MPROC_SIGNAL_GLINK_QMP
 						     IRQ_TYPE_EDGE_RISING>;
@@ -972,27 +1762,154 @@
 			wakeup-parent = <&pdc>;
 
 			qup_uart3_default_state: qup-uart3-default-state {
-				rx {
+				rx-pins {
 					pins = "gpio18";
 					function = "qup3";
 				};
-				tx {
+				tx-pins {
 					pins = "gpio19";
 					function = "qup3";
 				};
 			};
 
-			qup_i2c13_default_state: qup-i2c13-default-state {
-				mux {
-					pins = "gpio0", "gpio1";
-					function = "qup13";
-				};
+			qup_uart6_default: qup-uart6-default-state {
+				pins = "gpio30", "gpio31";
+				function = "qup6";
+				drive-strength = <2>;
+				bias-disable;
+			};
 
-				config {
-					pins = "gpio0", "gpio1";
-					drive-strength = <2>;
-					bias-pull-up;
-				};
+			qup_uart18_default: qup-uart18-default-state {
+				pins = "gpio58", "gpio59";
+				function = "qup18";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			qup_i2c0_default: qup-i2c0-default-state {
+				pins = "gpio4", "gpio5";
+				function = "qup0";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			qup_i2c1_default: qup-i2c1-default-state {
+				pins = "gpio8", "gpio9";
+				function = "qup1";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			qup_i2c2_default: qup-i2c2-default-state {
+				pins = "gpio12", "gpio13";
+				function = "qup2";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			qup_i2c4_default: qup-i2c4-default-state {
+				pins = "gpio20", "gpio21";
+				function = "qup4";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			qup_i2c5_default: qup-i2c5-default-state {
+				pins = "gpio24", "gpio25";
+				function = "qup5";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			qup_i2c6_default: qup-i2c6-default-state {
+				pins = "gpio28", "gpio29";
+				function = "qup6";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			qup_i2c7_default: qup-i2c7-default-state {
+				pins = "gpio32", "gpio33";
+				function = "qup7";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			qup_i2c8_default: qup-i2c8-default-state {
+				pins = "gpio36", "gpio37";
+				function = "qup8";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			qup_i2c9_default: qup-i2c9-default-state {
+				pins = "gpio40", "gpio41";
+				function = "qup9";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			qup_i2c10_default: qup-i2c10-default-state {
+				pins = "gpio44", "gpio45";
+				function = "qup10";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			qup_i2c11_default: qup-i2c11-default-state {
+				pins = "gpio48", "gpio49";
+				function = "qup11";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			qup_i2c12_default: qup-i2c12-default-state {
+				pins = "gpio52", "gpio53";
+				function = "qup12";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			qup_i2c13_default: qup-i2c13-default-state {
+				pins = "gpio0", "gpio1";
+				function = "qup13";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			qup_i2c14_default: qup-i2c14-default-state {
+				pins = "gpio56", "gpio57";
+				function = "qup14";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			qup_i2c15_default: qup-i2c15-default-state {
+				pins = "gpio60", "gpio61";
+				function = "qup15";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			qup_i2c16_default: qup-i2c16-default-state {
+				pins = "gpio64", "gpio65";
+				function = "qup16";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			qup_i2c17_default: qup-i2c17-default-state {
+				pins = "gpio72", "gpio73";
+				function = "qup17";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			qup_i2c19_default: qup-i2c19-default-state {
+				pins = "gpio76", "gpio77";
+				function = "qup19";
+				drive-strength = <2>;
+				bias-disable;
 			};
 		};
 
@@ -1007,6 +1924,8 @@
 			compatible = "arm,gic-v3";
 			#interrupt-cells = <3>;
 			interrupt-controller;
+			#redistributor-regions = <1>;
+			redistributor-stride = <0 0x20000>;
 			reg = <0x0 0x17a00000 0x0 0x10000>,     /* GICD */
 			      <0x0 0x17a60000 0x0 0x100000>;    /* GICR * 8 */
 			interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
@@ -1014,9 +1933,9 @@
 
 		timer@17c20000 {
 			compatible = "arm,armv7-timer-mem";
-			#address-cells = <2>;
-			#size-cells = <2>;
-			ranges;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0 0 0x20000000>;
 			reg = <0x0 0x17c20000 0x0 0x1000>;
 			clock-frequency = <19200000>;
 
@@ -1024,49 +1943,49 @@
 				frame-number = <0>;
 				interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
 					     <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0x0 0x17c21000 0x0 0x1000>,
-				      <0x0 0x17c22000 0x0 0x1000>;
+				reg = <0x17c21000 0x1000>,
+				      <0x17c22000 0x1000>;
 			};
 
 			frame@17c23000 {
 				frame-number = <1>;
 				interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0x0 0x17c23000 0x0 0x1000>;
+				reg = <0x17c23000 0x1000>;
 				status = "disabled";
 			};
 
 			frame@17c25000 {
 				frame-number = <2>;
 				interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0x0 0x17c25000 0x0 0x1000>;
+				reg = <0x17c25000 0x1000>;
 				status = "disabled";
 			};
 
 			frame@17c27000 {
 				frame-number = <3>;
 				interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0x0 0x17c27000 0x0 0x1000>;
+				reg = <0x17c27000 0x1000>;
 				status = "disabled";
 			};
 
 			frame@17c29000 {
 				frame-number = <4>;
 				interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0x0 0x17c29000 0x0 0x1000>;
+				reg = <0x17c29000 0x1000>;
 				status = "disabled";
 			};
 
 			frame@17c2b000 {
 				frame-number = <5>;
 				interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0x0 0x17c2b000 0x0 0x1000>;
+				reg = <0x17c2b000 0x1000>;
 				status = "disabled";
 			};
 
 			frame@17c2d000 {
 				frame-number = <6>;
 				interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0x0 0x17c2d000 0x0 0x1000>;
+				reg = <0x17c2d000 0x1000>;
 				status = "disabled";
 			};
 		};
@@ -1084,7 +2003,7 @@
 			qcom,tcs-offset = <0xd00>;
 			qcom,drv-id = <2>;
 			qcom,tcs-config = <ACTIVE_TCS  2>, <SLEEP_TCS   3>,
-					  <WAKE_TCS    3>, <CONTROL_TCS 1>;
+					  <WAKE_TCS    3>, <CONTROL_TCS 0>;
 
 			rpmhcc: clock-controller {
 				compatible = "qcom,sm8350-rpmh-clk";
@@ -1143,7 +2062,7 @@
 				};
 			};
 
-			apps_bcm_voter: bcm_voter {
+			apps_bcm_voter: bcm-voter {
 				compatible = "qcom,bcm-voter";
 			};
 		};
@@ -1178,7 +2097,6 @@
 			iommus = <&apps_smmu 0xe0 0x0>;
 
 			clock-names =
-				"ref_clk",
 				"core_clk",
 				"bus_aggr_clk",
 				"iface_clk",
@@ -1188,7 +2106,6 @@
 				"rx_lane0_sync_clk",
 				"rx_lane1_sync_clk";
 			clocks =
-				<&rpmhcc RPMH_CXO_CLK>,
 				<&gcc GCC_UFS_PHY_AXI_CLK>,
 				<&gcc GCC_AGGRE_UFS_PHY_AXI_CLK>,
 				<&gcc GCC_UFS_PHY_AHB_CLK>,
@@ -1199,20 +2116,19 @@
 				<&gcc GCC_UFS_PHY_RX_SYMBOL_1_CLK>;
 			freq-table-hz =
 				<75000000 300000000>,
-				<75000000 300000000>,
 				<0 0>,
 				<0 0>,
 				<75000000 300000000>,
 				<0 0>,
 				<0 0>,
-				<75000000 300000000>,
-				<75000000 300000000>;
+				<0 0>,
+				<0 0>;
 			status = "disabled";
 		};
 
 		ufs_mem_phy: phy@1d87000 {
 			compatible = "qcom,sm8350-qmp-ufs-phy";
-			reg = <0 0x01d87000 0 0xe10>;
+			reg = <0 0x01d87000 0 0x1c4>;
 			#address-cells = <2>;
 			#size-cells = <2>;
 			ranges;
@@ -1232,7 +2148,6 @@
 				      <0 0x01d87800 0 0x108>,
 				      <0 0x01d87a00 0 0x1e0>;
 				#phy-cells = <0>;
-				#clock-cells = <0>;
 			};
 		};
 
@@ -1251,8 +2166,8 @@
 			clocks = <&rpmhcc RPMH_CXO_CLK>;
 			clock-names = "xo";
 
-			power-domains = <&rpmhpd 4>,
-					<&rpmhpd 5>;
+			power-domains = <&rpmhpd SM8350_LCX>,
+					<&rpmhpd SM8350_LMX>;
 			power-domain-names = "lcx", "lmx";
 
 			memory-region = <&pil_slpi_mem>;
@@ -1278,6 +2193,7 @@
 					compatible = "qcom,fastrpc";
 					qcom,glink-channels = "fastrpcglink-apps-dsp";
 					label = "sdsp";
+					qcom,non-secure-domain;
 					#address-cells = <1>;
 					#size-cells = <0>;
 
@@ -1318,8 +2234,8 @@
 			clocks = <&rpmhcc RPMH_CXO_CLK>;
 			clock-names = "xo";
 
-			power-domains = <&rpmhpd 0>,
-					<&rpmhpd 10>;
+			power-domains = <&rpmhpd SM8350_CX>,
+					<&rpmhpd SM8350_MXC>;
 			power-domain-names = "cx", "mxc";
 
 			interconnects = <&compute_noc MASTER_CDSP_PROC &mc_virt SLAVE_EBI1>;
@@ -1347,6 +2263,7 @@
 					compatible = "qcom,fastrpc";
 					qcom,glink-channels = "fastrpcglink-apps-dsp";
 					label = "cdsp";
+					qcom,non-secure-domain;
 					#address-cells = <1>;
 					#size-cells = <0>;
 
@@ -1463,7 +2380,7 @@
 				      <0 0x088e9800 0 0x200>,
 				      <0 0x088e9a00 0 0x100>;
 				#phy-cells = <0>;
-				#clock-cells = <1>;
+				#clock-cells = <0>;
 				clocks = <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>;
 				clock-names = "pipe0";
 				clock-output-names = "usb3_phy_pipe_clk_src";
@@ -1493,7 +2410,7 @@
 				      <0 0x088ec000 0 0x200>,
 				      <0 0x088eb200 0 0x1100>;
 				#phy-cells = <0>;
-				#clock-cells = <1>;
+				#clock-cells = <0>;
 				clocks = <&gcc GCC_USB3_SEC_PHY_PIPE_CLK>;
 				clock-names = "pipe0";
 				clock-output-names = "usb3_uni_phy_pipe_clk_src";
@@ -1514,6 +2431,12 @@
 			qcom,bcm-voters = <&apps_bcm_voter>;
 		};
 
+		system-cache-controller@9200000 {
+			compatible = "qcom,sm8350-llcc";
+			reg = <0 0x09200000 0 0x1d0000>, <0 0x09600000 0 0x50000>;
+			reg-names = "llcc_base", "llcc_broadcast_base";
+		};
+
 		usb_1: usb@a6f8800 {
 			compatible = "qcom,sm8350-dwc3", "qcom,dwc3";
 			reg = <0 0x0a6f8800 0 0x400>;
@@ -1525,21 +2448,26 @@
 			clocks = <&gcc GCC_CFG_NOC_USB3_PRIM_AXI_CLK>,
 				 <&gcc GCC_USB30_PRIM_MASTER_CLK>,
 				 <&gcc GCC_AGGRE_USB3_PRIM_AXI_CLK>,
-				 <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
-				 <&gcc GCC_USB30_PRIM_SLEEP_CLK>;
-			clock-names = "cfg_noc", "core", "iface", "mock_utmi",
-				      "sleep";
+				 <&gcc GCC_USB30_PRIM_SLEEP_CLK>,
+				 <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>;
+			clock-names = "cfg_noc",
+				      "core",
+				      "iface",
+				      "sleep",
+				      "mock_utmi";
 
 			assigned-clocks = <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
 					  <&gcc GCC_USB30_PRIM_MASTER_CLK>;
 			assigned-clock-rates = <19200000>, <200000000>;
 
 			interrupts-extended = <&intc GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>,
-					      <&pdc 14 IRQ_TYPE_EDGE_BOTH>,
+					      <&pdc 17 IRQ_TYPE_LEVEL_HIGH>,
 					      <&pdc 15 IRQ_TYPE_EDGE_BOTH>,
-					      <&pdc 17 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "hs_phy_irq", "dp_hs_phy_irq",
-					  "dm_hs_phy_irq", "ss_phy_irq";
+					      <&pdc 14 IRQ_TYPE_EDGE_BOTH>;
+			interrupt-names = "hs_phy_irq",
+					  "ss_phy_irq",
+					  "dm_hs_phy_irq",
+					  "dp_hs_phy_irq";
 
 			power-domains = <&gcc USB30_PRIM_GDSC>;
 
@@ -1568,22 +2496,28 @@
 			clocks = <&gcc GCC_CFG_NOC_USB3_SEC_AXI_CLK>,
 				 <&gcc GCC_USB30_SEC_MASTER_CLK>,
 				 <&gcc GCC_AGGRE_USB3_SEC_AXI_CLK>,
-				 <&gcc GCC_USB30_SEC_MOCK_UTMI_CLK>,
 				 <&gcc GCC_USB30_SEC_SLEEP_CLK>,
+				 <&gcc GCC_USB30_SEC_MOCK_UTMI_CLK>,
 				 <&gcc GCC_USB3_SEC_CLKREF_EN>;
-			clock-names = "cfg_noc", "core", "iface", "mock_utmi",
-				      "sleep", "xo";
+			clock-names = "cfg_noc",
+				      "core",
+				      "iface",
+				      "sleep",
+				      "mock_utmi",
+				      "xo";
 
 			assigned-clocks = <&gcc GCC_USB30_SEC_MOCK_UTMI_CLK>,
 					  <&gcc GCC_USB30_SEC_MASTER_CLK>;
 			assigned-clock-rates = <19200000>, <200000000>;
 
 			interrupts-extended = <&intc GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>,
-					      <&pdc 12 IRQ_TYPE_EDGE_BOTH>,
+					      <&pdc 16 IRQ_TYPE_LEVEL_HIGH>,
 					      <&pdc 13 IRQ_TYPE_EDGE_BOTH>,
-					      <&pdc 16 IRQ_TYPE_LEVEL_HIGH>;
-			interrupt-names = "hs_phy_irq", "dp_hs_phy_irq",
-					  "dm_hs_phy_irq", "ss_phy_irq";
+					      <&pdc 12 IRQ_TYPE_EDGE_BOTH>;
+			interrupt-names = "hs_phy_irq",
+					  "ss_phy_irq",
+					  "dm_hs_phy_irq",
+					  "dp_hs_phy_irq";
 
 			power-domains = <&gcc USB30_SEC_GDSC>;
 
@@ -1601,6 +2535,31 @@
 			};
 		};
 
+		dispcc: clock-controller@af00000 {
+			compatible = "qcom,sm8350-dispcc";
+			reg = <0 0x0af00000 0 0x10000>;
+			clocks = <&rpmhcc RPMH_CXO_CLK>,
+				 <0>,
+				 <0>,
+				 <0>,
+				 <0>,
+				 <0>,
+				 <0>;
+			clock-names = "bi_tcxo",
+				      "dsi0_phy_pll_out_byteclk",
+				      "dsi0_phy_pll_out_dsiclk",
+				      "dsi1_phy_pll_out_byteclk",
+				      "dsi1_phy_pll_out_dsiclk",
+				      "dp_phy_pll_link_clk",
+				      "dp_phy_pll_vco_div_clk";
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+			#power-domain-cells = <1>;
+
+			power-domains = <&rpmhpd SM8350_MMCX>;
+			power-domain-names = "mmcx";
+		};
+
 		adsp: remoteproc@17300000 {
 			compatible = "qcom,sm8350-adsp-pas";
 			reg = <0 0x17300000 0 0x100>;
@@ -1616,8 +2575,8 @@
 			clocks = <&rpmhcc RPMH_CXO_CLK>;
 			clock-names = "xo";
 
-			power-domains = <&rpmhpd 4>,
-					<&rpmhpd 5>;
+			power-domains = <&rpmhpd SM8350_LCX>,
+					<&rpmhpd SM8350_LMX>;
 			power-domain-names = "lcx", "lmx";
 
 			memory-region = <&pil_adsp_mem>;
@@ -1643,6 +2602,7 @@
 					compatible = "qcom,fastrpc";
 					qcom,glink-channels = "fastrpcglink-apps-dsp";
 					label = "adsp";
+					qcom,non-secure-domain;
 					#address-cells = <1>;
 					#size-cells = <0>;
 
@@ -2267,7 +3227,7 @@
 			};
 		};
 
-		gpu-thermal-top {
+		gpu-top-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 
@@ -2282,7 +3242,7 @@
 			};
 		};
 
-		gpu-thermal-bottom {
+		gpu-bottom-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 
@@ -2372,7 +3332,7 @@
 			};
 		};
 
-		modem1-thermal-top {
+		modem1-top-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 
@@ -2387,7 +3347,7 @@
 			};
 		};
 
-		modem2-thermal-top {
+		modem2-top-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 
@@ -2402,7 +3362,7 @@
 			};
 		};
 
-		modem3-thermal-top {
+		modem3-top-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 
@@ -2417,7 +3377,7 @@
 			};
 		};
 
-		modem4-thermal-top {
+		modem4-top-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 
@@ -2432,7 +3392,7 @@
 			};
 		};
 
-		camera-thermal-top {
+		camera-top-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 
@@ -2447,7 +3407,7 @@
 			};
 		};
 
-		camera-thermal-bottom {
+		cam-bottom-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 
diff --git a/arch/arm64/boot/dts/qcom/sm8450-hdk.dts b/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
new file mode 100644
index 000000000000..38ccd44620d0
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sm8450-hdk.dts
@@ -0,0 +1,444 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2022, Linaro Limited
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+#include "sm8450.dtsi"
+
+/ {
+	model = "Qualcomm Technologies, Inc. SM8450 HDK";
+	compatible = "qcom,sm8450-hdk", "qcom,sm8450";
+
+	aliases {
+		serial0 = &uart7;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	vph_pwr: vph-pwr-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vph_pwr";
+		regulator-min-microvolt = <3700000>;
+		regulator-max-microvolt = <3700000>;
+
+		regulator-always-on;
+		regulator-boot-on;
+	};
+};
+
+&apps_rsc {
+	pm8350-rpmh-regulators {
+		compatible = "qcom,pm8350-rpmh-regulators";
+		qcom,pmic-id = "b";
+
+		vdd-s1-supply = <&vph_pwr>;
+		vdd-s2-supply = <&vph_pwr>;
+		vdd-s3-supply = <&vph_pwr>;
+		vdd-s4-supply = <&vph_pwr>;
+		vdd-s5-supply = <&vph_pwr>;
+		vdd-s6-supply = <&vph_pwr>;
+		vdd-s7-supply = <&vph_pwr>;
+		vdd-s8-supply = <&vph_pwr>;
+		vdd-s9-supply = <&vph_pwr>;
+		vdd-s10-supply = <&vph_pwr>;
+		vdd-s11-supply = <&vph_pwr>;
+		vdd-s12-supply = <&vph_pwr>;
+
+		vdd-l1-l4-supply = <&vreg_s11b_0p95>;
+		vdd-l2-l7-supply = <&vreg_bob>;
+		vdd-l3-l5-supply = <&vreg_bob>;
+		vdd-l6-l9-l10-supply = <&vreg_s12b_1p25>;
+		vdd-l8-supply = <&vreg_s2h_0p95>;
+
+		vreg_s10b_1p8: smps10 {
+			regulator-name = "vreg_s10b_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		vreg_s11b_0p95: smps11 {
+			regulator-name = "vreg_s11b_0p95";
+			regulator-min-microvolt = <966000>;
+			regulator-max-microvolt = <1104000>;
+		};
+
+		vreg_s12b_1p25: smps12 {
+			regulator-name = "vreg_s12b_1p25";
+			regulator-min-microvolt = <1350000>;
+			regulator-max-microvolt = <1400000>;
+		};
+
+		vreg_l1b_0p91: ldo1 {
+			regulator-name = "vreg_l1b_0p91";
+			regulator-min-microvolt = <912000>;
+			regulator-max-microvolt = <920000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2b_3p07: ldo2 {
+			regulator-name = "vreg_l2b_3p07";
+			regulator-min-microvolt = <3072000>;
+			regulator-max-microvolt = <3072000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3b_0p9: ldo3 {
+			regulator-name = "vreg_l3b_0p9";
+			regulator-min-microvolt = <904000>;
+			regulator-max-microvolt = <904000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l5b_0p88: ldo5 {
+			regulator-name = "vreg_l5b_0p88";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <888000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l6b_1p2: ldo6 {
+			regulator-name = "vreg_l6b_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l7b_2p5: ldo7 {
+			regulator-name = "vreg_l7b_2p5";
+			regulator-min-microvolt = <2504000>;
+			regulator-max-microvolt = <2504000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l9b_1p2: ldo9 {
+			regulator-name = "vreg_l9b_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	pm8350c-rpmh-regulators {
+		compatible = "qcom,pm8350c-rpmh-regulators";
+		qcom,pmic-id = "c";
+
+		vdd-s1-supply = <&vph_pwr>;
+		vdd-s2-supply = <&vph_pwr>;
+		vdd-s3-supply = <&vph_pwr>;
+		vdd-s4-supply = <&vph_pwr>;
+		vdd-s5-supply = <&vph_pwr>;
+		vdd-s6-supply = <&vph_pwr>;
+		vdd-s7-supply = <&vph_pwr>;
+		vdd-s8-supply = <&vph_pwr>;
+		vdd-s9-supply = <&vph_pwr>;
+		vdd-s10-supply = <&vph_pwr>;
+
+		vdd-l1-l12-supply = <&vreg_bob>;
+		vdd-l2-l8-supply = <&vreg_bob>;
+		vdd-l3-l4-l5-l7-l13-supply = <&vreg_bob>;
+		vdd-l6-l9-l11-supply = <&vreg_bob>;
+		vdd-l10-supply = <&vreg_s12b_1p25>;
+
+		vdd-bob-supply = <&vph_pwr>;
+
+		vreg_s1c_1p86: smps1 {
+			regulator-name = "vreg_s1c_1p86";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2024000>;
+		};
+
+		vreg_s10c_1p05: smps10 {
+			regulator-name = "vreg_s10c_1p05";
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1100000>;
+		};
+
+		vreg_bob: bob {
+			regulator-name = "vreg_bob";
+			regulator-min-microvolt = <3008000>;
+			regulator-max-microvolt = <3960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>;
+		};
+
+		vreg_l1c_1p8: ldo1 {
+			regulator-name = "vreg_l1c_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3c_3p0: ldo3 {
+			regulator-name = "vreg_l3c_3p0";
+			regulator-min-microvolt = <3296000>;
+			regulator-max-microvolt = <3304000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l4c_1p8: ldo4 {
+			regulator-name = "vreg_l4c_1p8";
+			regulator-min-microvolt = <1704000>;
+			regulator-max-microvolt = <3000000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l5c_1p8: ldo5 {
+			regulator-name = "vreg_l5c_1p8";
+			regulator-min-microvolt = <1704000>;
+			regulator-max-microvolt = <3000000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l6c_1p8: ldo6 {
+			regulator-name = "vreg_l6c_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <3008000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l7c_3p0: ldo7 {
+			regulator-name = "vreg_l7c_3p0";
+			regulator-min-microvolt = <3008000>;
+			regulator-max-microvolt = <3008000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l8c_1p8: ldo8 {
+			regulator-name = "vreg_l8c_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l9c_2p96: ldo9 {
+			regulator-name = "vreg_l9c_2p96";
+			regulator-min-microvolt = <2960000>;
+			regulator-max-microvolt = <3008000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l12c_1p8: ldo12 {
+			regulator-name = "vreg_l12c_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1968000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l13c_3p0: ldo13 {
+			regulator-name = "vreg_l13c_3p0";
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	pm8450-rpmh-regulators {
+		compatible = "qcom,pm8450-rpmh-regulators";
+		qcom,pmic-id = "h";
+
+		vdd-s1-supply = <&vph_pwr>;
+		vdd-s2-supply = <&vph_pwr>;
+		vdd-s3-supply = <&vph_pwr>;
+		vdd-s4-supply = <&vph_pwr>;
+		vdd-s5-supply = <&vph_pwr>;
+		vdd-s6-supply = <&vph_pwr>;
+
+		vdd-l2-supply = <&vreg_bob>;
+		vdd-l3-supply = <&vreg_bob>;
+		vdd-l4-supply = <&vreg_bob>;
+
+		vreg_s2h_0p95: smps2 {
+			regulator-name = "vreg_s2h_0p95";
+			regulator-min-microvolt = <848000>;
+			regulator-max-microvolt = <1104000>;
+		};
+
+		vreg_s3h_0p5: smps3 {
+			regulator-name = "vreg_s3h_0p5";
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <500000>;
+		};
+
+		vreg_l2h_0p91: ldo2 {
+			regulator-name = "vreg_l2h_0p91";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3h_0p91: ldo3 {
+			regulator-name = "vreg_l3h_0p91";
+			regulator-min-microvolt = <912000>;
+			regulator-max-microvolt = <912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+	};
+
+	pmr735a-rpmh-regulators {
+		compatible = "qcom,pmr735a-rpmh-regulators";
+		qcom,pmic-id = "e";
+
+		vdd-s1-supply = <&vph_pwr>;
+		vdd-s2-supply = <&vph_pwr>;
+		vdd-s3-supply = <&vph_pwr>;
+
+		vdd-l1-l2-supply = <&vreg_s2e_0p85>;
+		vdd-l3-supply = <&vreg_s1e_1p25>;
+		vdd-l4-supply = <&vreg_s1c_1p86>;
+		vdd-l5-l6-supply = <&vreg_s1c_1p86>;
+		vdd-l7-bob-supply = <&vreg_bob>;
+
+		vreg_s1e_1p25: smps1 {
+			regulator-name = "vreg_s1e_1p25";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1296000>;
+		};
+
+		vreg_s2e_0p85: smps2 {
+			regulator-name = "vreg_s2e_0p85";
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1040000>;
+		};
+
+		vreg_l1e_0p8: ldo1 {
+			regulator-name = "vreg_l1e_0p8";
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <800000>;
+		};
+
+		vreg_l2e_0p8: ldo2 {
+			regulator-name = "vreg_l2e_0p8";
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <800000>;
+		};
+
+		vreg_l3e_1p2: ldo3 {
+			regulator-name = "vreg_l3e_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		vreg_l4e_1p7: ldo4 {
+			regulator-name = "vreg_l4e_1p7";
+			regulator-min-microvolt = <1776000>;
+			regulator-max-microvolt = <1776000>;
+		};
+
+		vreg_l5e_0p88: ldo5 {
+			regulator-name = "vreg_l5e_0p88";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <880000>;
+		};
+
+		vreg_l6e_1p2: ldo6 {
+			regulator-name = "vreg_l6e_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		vreg_l7e_2p8: ldo7 {
+			regulator-name = "vreg_l7e_2p8";
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+		};
+	};
+};
+
+&pcie0 {
+	status = "okay";
+	max-link-speed = <2>;
+};
+
+&pcie0_phy {
+	status = "okay";
+	vdda-phy-supply = <&vreg_l5b_0p88>;
+	vdda-pll-supply = <&vreg_l6b_1p2>;
+};
+
+&pcie1 {
+	status = "okay";
+};
+
+&pcie1_phy {
+	status = "okay";
+	vdda-phy-supply = <&vreg_l2h_0p91>;
+	vdda-pll-supply = <&vreg_l6b_1p2>;
+};
+
+&remoteproc_adsp {
+	status = "okay";
+	firmware-name = "qcom/sm8450/adsp.mbn";
+};
+
+&remoteproc_cdsp {
+	status = "okay";
+	firmware-name = "qcom/sm8450/cdsp.mbn";
+};
+
+&remoteproc_mpss {
+	status = "okay";
+	firmware-name = "qcom/sm8450/modem.mbn";
+};
+
+&remoteproc_slpi {
+	status = "okay";
+	firmware-name = "qcom/sm8450/slpi.mbn";
+};
+
+&qupv3_id_0 {
+	status = "okay";
+};
+
+&tlmm {
+	gpio-reserved-ranges = <28 4>, <36 4>;
+};
+
+&uart7 {
+	status = "okay";
+};
+
+&ufs_mem_hc {
+	status = "okay";
+
+	reset-gpios = <&tlmm 210 GPIO_ACTIVE_LOW>;
+
+	vcc-supply = <&vreg_l7b_2p5>;
+	vcc-max-microamp = <1100000>;
+	vccq-supply = <&vreg_l9b_1p2>;
+	vccq-max-microamp = <1200000>;
+};
+
+&ufs_mem_phy {
+	status = "okay";
+
+	vdda-phy-supply = <&vreg_l5b_0p88>;
+	vdda-pll-supply = <&vreg_l6b_1p2>;
+};
+
+&usb_1 {
+	status = "okay";
+};
+
+&usb_1_dwc3 {
+	dr_mode = "peripheral";
+};
+
+&usb_1_hsphy {
+	status = "okay";
+
+	vdda-pll-supply = <&vreg_l5b_0p88>;
+	vdda18-supply = <&vreg_l1c_1p8>;
+	vdda33-supply = <&vreg_l2b_3p07>;
+};
+
+&usb_1_qmpphy {
+	status = "okay";
+
+	vdda-phy-supply = <&vreg_l6b_1p2>;
+	vdda-pll-supply = <&vreg_l1b_0p91>;
+};
diff --git a/arch/arm64/boot/dts/qcom/sm8450-qrd.dts b/arch/arm64/boot/dts/qcom/sm8450-qrd.dts
new file mode 100644
index 000000000000..e58fc7399799
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sm8450-qrd.dts
@@ -0,0 +1,450 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, Linaro Limited
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+#include "sm8450.dtsi"
+
+/ {
+	model = "Qualcomm Technologies, Inc. SM8450 QRD";
+	compatible = "qcom,sm8450-qrd", "qcom,sm8450";
+
+	aliases {
+		serial0 = &uart7;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	vph_pwr: vph-pwr-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vph_pwr";
+		regulator-min-microvolt = <3700000>;
+		regulator-max-microvolt = <3700000>;
+
+		regulator-always-on;
+		regulator-boot-on;
+	};
+};
+
+&apps_rsc {
+	pm8350-rpmh-regulators {
+		compatible = "qcom,pm8350-rpmh-regulators";
+		qcom,pmic-id = "b";
+
+		vdd-s1-supply = <&vph_pwr>;
+		vdd-s2-supply = <&vph_pwr>;
+		vdd-s3-supply = <&vph_pwr>;
+		vdd-s4-supply = <&vph_pwr>;
+		vdd-s5-supply = <&vph_pwr>;
+		vdd-s6-supply = <&vph_pwr>;
+		vdd-s7-supply = <&vph_pwr>;
+		vdd-s8-supply = <&vph_pwr>;
+		vdd-s9-supply = <&vph_pwr>;
+		vdd-s10-supply = <&vph_pwr>;
+		vdd-s11-supply = <&vph_pwr>;
+		vdd-s12-supply = <&vph_pwr>;
+
+		vdd-l1-l4-supply = <&vreg_s11b_0p95>;
+		vdd-l2-l7-supply = <&vreg_bob>;
+		vdd-l3-l5-supply = <&vreg_bob>;
+		vdd-l6-l9-l10-supply = <&vreg_s12b_1p25>;
+		vdd-l8-supply = <&vreg_s2h_0p95>;
+
+		vreg_s10b_1p8: smps10 {
+			regulator-name = "vreg_s10b_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		vreg_s11b_0p95: smps11 {
+			regulator-name = "vreg_s11b_0p95";
+			regulator-min-microvolt = <848000>;
+			regulator-max-microvolt = <1104000>;
+		};
+
+		vreg_s12b_1p25: smps12 {
+			regulator-name = "vreg_s12b_1p25";
+			regulator-min-microvolt = <1224000>;
+			regulator-max-microvolt = <1400000>;
+		};
+
+		vreg_l1b_0p91: ldo1 {
+			regulator-name = "vreg_l1b_0p91";
+			regulator-min-microvolt = <912000>;
+			regulator-max-microvolt = <920000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2b_3p07: ldo2 {
+			regulator-name = "vreg_l2b_3p07";
+			regulator-min-microvolt = <3072000>;
+			regulator-max-microvolt = <3072000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3b_0p9: ldo3 {
+			regulator-name = "vreg_l3b_0p9";
+			regulator-min-microvolt = <904000>;
+			regulator-max-microvolt = <904000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l5b_0p88: ldo5 {
+			regulator-name = "vreg_l5b_0p88";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <888000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l6b_1p2: ldo6 {
+			regulator-name = "vreg_l6b_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l7b_2p5: ldo7 {
+			regulator-name = "vreg_l7b_2p5";
+			regulator-min-microvolt = <2504000>;
+			regulator-max-microvolt = <2504000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l9b_1p2: ldo9 {
+			regulator-name = "vreg_l9b_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	pm8350c-rpmh-regulators {
+		compatible = "qcom,pm8350c-rpmh-regulators";
+		qcom,pmic-id = "c";
+
+		vdd-s1-supply = <&vph_pwr>;
+		vdd-s2-supply = <&vph_pwr>;
+		vdd-s3-supply = <&vph_pwr>;
+		vdd-s4-supply = <&vph_pwr>;
+		vdd-s5-supply = <&vph_pwr>;
+		vdd-s6-supply = <&vph_pwr>;
+		vdd-s7-supply = <&vph_pwr>;
+		vdd-s8-supply = <&vph_pwr>;
+		vdd-s9-supply = <&vph_pwr>;
+		vdd-s10-supply = <&vph_pwr>;
+
+		vdd-l1-l12-supply = <&vreg_bob>;
+		vdd-l2-l8-supply = <&vreg_bob>;
+		vdd-l3-l4-l5-l7-l13-supply = <&vreg_bob>;
+		vdd-l6-l9-l11-supply = <&vreg_bob>;
+
+		vdd-bob-supply = <&vph_pwr>;
+
+		vreg_s1c_1p86: smps1 {
+			regulator-name = "vreg_s1c_1p86";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2024000>;
+		};
+
+		vreg_s10c_1p05: smps10 {
+			regulator-name = "vreg_s10c_1p05";
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1100000>;
+		};
+
+		vreg_bob: bob {
+			regulator-name = "vreg_bob";
+			regulator-min-microvolt = <3008000>;
+			regulator-max-microvolt = <3960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>;
+		};
+
+		vreg_l1c_1p8: ldo1 {
+			regulator-name = "vreg_l1c_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3c_3p0: ldo3 {
+			regulator-name = "vreg_l3c_3p0";
+			regulator-min-microvolt = <3296000>;
+			regulator-max-microvolt = <3304000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l4c_1p8: ldo4 {
+			regulator-name = "vreg_l4c_1p8";
+			regulator-min-microvolt = <1704000>;
+			regulator-max-microvolt = <3000000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l5c_1p8: ldo5 {
+			regulator-name = "vreg_l5c_1p8";
+			regulator-min-microvolt = <1704000>;
+			regulator-max-microvolt = <3000000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l6c_1p8: ldo6 {
+			regulator-name = "vreg_l6c_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <3008000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l7c_3p0: ldo7 {
+			regulator-name = "vreg_l7c_3p0";
+			regulator-min-microvolt = <3008000>;
+			regulator-max-microvolt = <3008000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l8c_1p8: ldo8 {
+			regulator-name = "vreg_l8c_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l9c_2p96: ldo9 {
+			regulator-name = "vreg_l9c_2p96";
+			regulator-min-microvolt = <2960000>;
+			regulator-max-microvolt = <3008000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l12c_1p8: ldo12 {
+			regulator-name = "vreg_l12c_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1968000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l13c_3p0: ldo13 {
+			regulator-name = "vreg_l13c_3p0";
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	pm8450-rpmh-regulators {
+		compatible = "qcom,pm8450-rpmh-regulators";
+		qcom,pmic-id = "h";
+
+		vdd-s1-supply = <&vph_pwr>;
+		vdd-s2-supply = <&vph_pwr>;
+		vdd-s3-supply = <&vph_pwr>;
+		vdd-s4-supply = <&vph_pwr>;
+		vdd-s5-supply = <&vph_pwr>;
+		vdd-s6-supply = <&vph_pwr>;
+
+		vdd-l2-supply = <&vreg_bob>;
+		vdd-l3-supply = <&vreg_bob>;
+		vdd-l4-supply = <&vreg_bob>;
+
+		vreg_s2h_0p95: smps2 {
+			regulator-name = "vreg_s2h_0p95";
+			regulator-min-microvolt = <848000>;
+			regulator-max-microvolt = <1104000>;
+		};
+
+		vreg_s3h_0p5: smps3 {
+			regulator-name = "vreg_s3h_0p5";
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <500000>;
+		};
+
+		vreg_l2h_0p91: ldo2 {
+			regulator-name = "vreg_l2h_0p91";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3h_0p91: ldo3 {
+			regulator-name = "vreg_l3h_0p91";
+			regulator-min-microvolt = <912000>;
+			regulator-max-microvolt = <912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+	};
+
+	pmr735a-rpmh-regulators {
+		compatible = "qcom,pmr735a-rpmh-regulators";
+		qcom,pmic-id = "e";
+
+		vdd-s1-supply = <&vph_pwr>;
+		vdd-s2-supply = <&vph_pwr>;
+		vdd-s3-supply = <&vph_pwr>;
+
+		vdd-l1-l2-supply = <&vreg_s2e_0p85>;
+		vdd-l3-supply = <&vreg_s1e_1p25>;
+		vdd-l4-supply = <&vreg_s1c_1p86>;
+		vdd-l5-l6-supply = <&vreg_s1c_1p86>;
+		vdd-l7-bob-supply = <&vreg_bob>;
+
+		vreg_s1e_1p25: smps1 {
+			regulator-name = "vreg_s1e_1p25";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1296000>;
+		};
+
+		vreg_s2e_0p85: smps2 {
+			regulator-name = "vreg_s2e_0p85";
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1040000>;
+		};
+
+		vreg_l1e_0p8: ldo1 {
+			regulator-name = "vreg_l1e_0p8";
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <800000>;
+		};
+
+		vreg_l2e_0p8: ldo2 {
+			regulator-name = "vreg_l2e_0p8";
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <800000>;
+		};
+
+		vreg_l3e_1p2: ldo3 {
+			regulator-name = "vreg_l3e_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		vreg_l4e_1p7: ldo4 {
+			regulator-name = "vreg_l4e_1p7";
+			regulator-min-microvolt = <1776000>;
+			regulator-max-microvolt = <1776000>;
+		};
+
+		vreg_l5e_0p88: ldo5 {
+			regulator-name = "vreg_l5e_0p88";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <880000>;
+		};
+
+		vreg_l6e_1p2: ldo6 {
+			regulator-name = "vreg_l6e_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+	};
+};
+
+&pcie0 {
+	status = "okay";
+};
+
+&pcie0_phy {
+	status = "okay";
+	vdda-phy-supply = <&vreg_l5b_0p88>;
+	vdda-pll-supply = <&vreg_l6b_1p2>;
+};
+
+&gpi_dma0 {
+	status = "okay";
+};
+
+&i2c5 {
+	status = "okay";
+};
+
+&qupv3_id_0 {
+	status = "okay";
+};
+
+&qupv3_id_2 {
+	status = "okay";
+};
+
+&remoteproc_adsp {
+	status = "okay";
+	firmware-name = "qcom/sm8450/adsp.mbn";
+};
+
+&remoteproc_cdsp {
+	status = "okay";
+	firmware-name = "qcom/sm8450/cdsp.mbn";
+};
+
+&remoteproc_mpss {
+	status = "okay";
+	firmware-name = "qcom/sm8450/modem.mbn";
+};
+
+&remoteproc_slpi {
+	status = "okay";
+	firmware-name = "qcom/sm8450/slpi.mbn";
+};
+
+&spi4 {
+	status = "okay";
+};
+
+&spi18 {
+	status = "okay";
+};
+
+&spi19 {
+	status = "okay";
+};
+
+&tlmm {
+	gpio-reserved-ranges = <28 4>, <36 4>;
+};
+
+&uart7 {
+	status = "okay";
+};
+
+&ufs_mem_hc {
+	status = "okay";
+
+	reset-gpios = <&tlmm 210 GPIO_ACTIVE_LOW>;
+
+	vcc-supply = <&vreg_l7b_2p5>;
+	vcc-max-microamp = <1100000>;
+	vccq-supply = <&vreg_l9b_1p2>;
+	vccq-max-microamp = <1200000>;
+};
+
+&ufs_mem_phy {
+	status = "okay";
+
+	vdda-phy-supply = <&vreg_l5b_0p88>;
+	vdda-pll-supply = <&vreg_l6b_1p2>;
+};
+
+&usb_1 {
+	status = "okay";
+};
+
+&usb_1_dwc3 {
+	dr_mode = "peripheral";
+};
+
+&usb_1_hsphy {
+	status = "okay";
+
+	vdda-pll-supply = <&vreg_l5b_0p88>;
+	vdda18-supply = <&vreg_l1c_1p8>;
+	vdda33-supply = <&vreg_l2b_3p07>;
+};
+
+&usb_1_qmpphy {
+	status = "okay";
+
+	vdda-phy-supply = <&vreg_l6b_1p2>;
+	vdda-pll-supply = <&vreg_l1b_0p91>;
+};
diff --git a/arch/arm64/boot/dts/qcom/sm8450-sony-xperia-nagara-pdx223.dts b/arch/arm64/boot/dts/qcom/sm8450-sony-xperia-nagara-pdx223.dts
new file mode 100644
index 000000000000..d68765eb6d4f
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sm8450-sony-xperia-nagara-pdx223.dts
@@ -0,0 +1,634 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2022, Konrad Dybcio <konrad.dybcio@somainline.org>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+#include "sm8450.dtsi"
+
+/delete-node/ &adsp_mem;
+/delete-node/ &rmtfs_mem;
+/delete-node/ &video_mem;
+
+/ {
+	model = "Sony Xperia 1 IV";
+	compatible = "sony,pdx223", "qcom,sm8450";
+	chassis-type = "handset";
+
+	aliases {
+		serial0 = &uart7;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	reserved-memory {
+		adsp_mem: memory@85700000 {
+			reg = <0x0 0x85700000 0x0 0x2800000>;
+			no-map;
+		};
+
+		video_mem: memory@9fd00000 {
+			reg = <0x0 0x9fd00000 0x0 0x700000>;
+			no-map;
+		};
+
+		rmtfs_mem: memory@f3300000 {
+			compatible = "qcom,rmtfs-mem";
+			reg = <0x0 0xf3300000 0x0 0x280000>;
+			no-map;
+
+			qcom,client-id = <1>;
+			qcom,vmid = <15>;
+		};
+
+		ramoops@ffc00000 {
+			compatible = "ramoops";
+			reg = <0 0xffc00000 0 0x200000>;
+			console-size = <0x40000>;
+			record-size = <0x1000>;
+			ecc-size = <16>;
+			no-map;
+		};
+	};
+
+	/* Sadly, the voltages for these GPIO regulators are unknown. */
+	imx650_vana_vreg: imx650-vana-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "imx650_vana_vreg";
+		gpio = <&tlmm 23 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	vph_pwr: vph-pwr-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vph_pwr";
+		regulator-min-microvolt = <3700000>;
+		regulator-max-microvolt = <3700000>;
+
+		regulator-always-on;
+		regulator-boot-on;
+	};
+};
+
+&apps_rsc {
+	pm8350-rpmh-regulators {
+		compatible = "qcom,pm8350-rpmh-regulators";
+		qcom,pmic-id = "b";
+
+		vdd-s1-supply = <&vph_pwr>;
+		vdd-s2-supply = <&vph_pwr>;
+		vdd-s3-supply = <&vph_pwr>;
+		vdd-s4-supply = <&vph_pwr>;
+		vdd-s5-supply = <&vph_pwr>;
+		vdd-s6-supply = <&vph_pwr>;
+		vdd-s7-supply = <&vph_pwr>;
+		vdd-s8-supply = <&vph_pwr>;
+		vdd-s9-supply = <&vph_pwr>;
+		vdd-s10-supply = <&vph_pwr>;
+		vdd-s11-supply = <&vph_pwr>;
+		vdd-s12-supply = <&vph_pwr>;
+
+		vdd-l1-l4-supply = <&pm8350_s11>;
+		vdd-l2-l7-supply = <&vreg_bob>;
+		vdd-l3-l5-supply = <&vreg_bob>;
+		vdd-l6-l9-l10-supply = <&pm8350_s12>;
+
+		/*
+		 * ARC regulators:
+		 * s5 - gfx.lvl
+		 * l8 - lcx.lvl
+		 */
+
+		pm8350_s10: smps10 {
+			regulator-name = "pm8350_s10";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8350_s11: smps11 {
+			regulator-name = "pm8350_s11";
+			regulator-min-microvolt = <848000>;
+			regulator-max-microvolt = <1104000>;
+		};
+
+		pm8350_s12: smps12 {
+			regulator-name = "pm8350_s12";
+			regulator-min-microvolt = <1224000>;
+			regulator-max-microvolt = <1400000>;
+		};
+
+		pm8350_l1: ldo1 {
+			regulator-name = "pm8350_l1";
+			regulator-min-microvolt = <912000>;
+			regulator-max-microvolt = <920000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		pm8350_l2: ldo2 {
+			regulator-name = "pm8350_l2";
+			regulator-min-microvolt = <3072000>;
+			regulator-max-microvolt = <3072000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		pm8350_l3: ldo3 {
+			regulator-name = "pm8350_l3";
+			regulator-min-microvolt = <904000>;
+			regulator-max-microvolt = <904000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		pm8350_l5: ldo5 {
+			regulator-name = "pm8350_l5";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		pm8350_l6: ldo6 {
+			regulator-name = "pm8350_l6";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		pm8350_l7: ldo7 {
+			regulator-name = "pm8350_l7";
+			regulator-min-microvolt = <2504000>;
+			regulator-max-microvolt = <2504000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		pm8350_l9: ldo9 {
+			regulator-name = "pm8350_l9";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	pm8350c-rpmh-regulators {
+		compatible = "qcom,pm8350c-rpmh-regulators";
+		qcom,pmic-id = "c";
+
+		vdd-s1-supply = <&vph_pwr>;
+		vdd-s2-supply = <&vph_pwr>;
+		vdd-s3-supply = <&vph_pwr>;
+		vdd-s4-supply = <&vph_pwr>;
+		vdd-s5-supply = <&vph_pwr>;
+		vdd-s6-supply = <&vph_pwr>;
+		vdd-s7-supply = <&vph_pwr>;
+		vdd-s8-supply = <&vph_pwr>;
+		vdd-s9-supply = <&vph_pwr>;
+		vdd-s10-supply = <&vph_pwr>;
+
+		vdd-l1-l12-supply = <&vreg_bob>;
+		vdd-l2-l8-supply = <&vreg_bob>;
+		vdd-l3-l4-l5-l7-l13-supply = <&vreg_bob>;
+		vdd-l6-l9-l11-supply = <&vreg_bob>;
+		vdd-l10-supply = <&pm8350_s12>;
+
+		vdd-bob-supply = <&vph_pwr>;
+
+		/*
+		 * ARC regulators:
+		 * s2 - mxc.lvl
+		 * s4 - mss.lvl
+		 * s6 - cx.lvl
+		 */
+
+		pm8350c_s1: smps1 {
+			regulator-name = "pm8350c_s1";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2024000>;
+		};
+
+		pm8350c_s10: smps10 {
+			regulator-name = "pm8350c_s10";
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1100000>;
+		};
+
+		vreg_bob: bob {
+			regulator-name = "vreg_bob";
+			regulator-min-microvolt = <3400000>;
+			regulator-max-microvolt = <3960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>;
+		};
+
+		pm8350c_l1: ldo1 {
+			regulator-name = "pm8350c_l1";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		pm8350c_l2: ldo2 {
+			regulator-name = "pm8350c_l2";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		pm8350c_l3: ldo3 {
+			regulator-name = "pm8350c_l3";
+			regulator-min-microvolt = <3296000>;
+			regulator-max-microvolt = <3304000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		pm8350c_l4: ldo4 {
+			regulator-name = "pm8350c_l4";
+			regulator-min-microvolt = <1704000>;
+			regulator-max-microvolt = <3000000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		pm8350c_l5: ldo5 {
+			regulator-name = "pm8350c_l5";
+			regulator-min-microvolt = <1704000>;
+			regulator-max-microvolt = <3000000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		pm8350c_l6: ldo6 {
+			regulator-name = "pm8350c_l6";
+			regulator-min-microvolt = <2960000>;
+			/* Originally max = 3008000 but SDHCI expects 2960000 */
+			regulator-max-microvolt = <2960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		pm8350c_l7: ldo7 {
+			regulator-name = "pm8350c_l7";
+			regulator-min-microvolt = <3008000>;
+			regulator-max-microvolt = <3008000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		pm8350c_l8: ldo8 {
+			regulator-name = "pm8350c_l8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		pm8350c_l9: ldo9 {
+			regulator-name = "pm8350c_l9";
+			regulator-min-microvolt = <2960000>;
+			/* Originally max = 3008000 but SDHCI expects 2960000 */
+			regulator-max-microvolt = <2960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		pm8350c_l10: ldo10 {
+			regulator-name = "pm8350c_l10";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		pm8350c_l12: ldo12 {
+			regulator-name = "pm8350c_l12";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1968000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		pm8350c_l13: ldo13 {
+			regulator-name = "pm8350c_l13";
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	pm8450-rpmh-regulators {
+		compatible = "qcom,pm8450-rpmh-regulators";
+		qcom,pmic-id = "h";
+
+		vdd-s1-supply = <&vph_pwr>;
+		vdd-s2-supply = <&vph_pwr>;
+		vdd-s3-supply = <&vph_pwr>;
+		vdd-s4-supply = <&vph_pwr>;
+		vdd-s5-supply = <&vph_pwr>;
+		vdd-s6-supply = <&vph_pwr>;
+
+		vdd-l2-supply = <&vreg_bob>;
+		vdd-l3-supply = <&vreg_bob>;
+		vdd-l4-supply = <&vreg_bob>;
+
+		/*
+		 * ARC regulators:
+		 * S2 - ebi.lvl
+		 * S4 - mmcx.lvl
+		 * S6 - mx.lvl
+		 * L1 - lmx.lvl
+		 */
+
+		pm8450_s3: smps3 {
+			regulator-name = "pm8450_s3";
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <600000>;
+		};
+
+		pm8450_l2: ldo2 {
+			regulator-name = "pm8450_l2";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		pm8450_l3: ldo3 {
+			regulator-name = "pm8450_l3";
+			regulator-min-microvolt = <912000>;
+			regulator-max-microvolt = <912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	pmr735a-rpmh-regulators {
+		compatible = "qcom,pmr735a-rpmh-regulators";
+		qcom,pmic-id = "e";
+
+		vdd-s1-supply = <&vph_pwr>;
+		vdd-s2-supply = <&vph_pwr>;
+		vdd-s3-supply = <&vph_pwr>;
+
+		vdd-l1-l2-supply = <&pmr735a_s2>;
+		vdd-l3-supply = <&pmr735a_s1>;
+		vdd-l4-supply = <&pm8350c_s1>;
+		vdd-l5-l6-supply = <&pm8350c_s1>;
+		vdd-l7-bob-supply = <&vreg_bob>;
+
+		pmr735a_s1: smps1 {
+			regulator-name = "pmr735a_s1";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1296000>;
+		};
+
+		pmr735a_s2: smps2 {
+			regulator-name = "pmr735a_s2";
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1040000>;
+		};
+
+		pmr735a_s3: smps3 {
+			regulator-name = "pmr735a_s3";
+			regulator-min-microvolt = <435000>;
+			regulator-max-microvolt = <2352000>;
+		};
+
+		pmr735a_l1: ldo1 {
+			regulator-name = "pmr735a_l1";
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <800000>;
+		};
+
+		pmr735a_l2: ldo2 {
+			regulator-name = "pmr735a_l2";
+			regulator-min-microvolt = <480000>;
+			regulator-max-microvolt = <912000>;
+		};
+
+		pmr735a_l3: ldo3 {
+			regulator-name = "pmr735a_l3";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pmr735a_l4: ldo4 {
+			regulator-name = "pmr735a_l4";
+			regulator-min-microvolt = <1776000>;
+			regulator-max-microvolt = <1776000>;
+		};
+
+		pmr735a_l5: ldo5 {
+			regulator-name = "pmr735a_l5";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <880000>;
+		};
+
+		pmr735a_l6: ldo6 {
+			regulator-name = "pmr735a_l6";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pmr735a_l7: ldo7 {
+			regulator-name = "pmr735a_l7";
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+		};
+	};
+};
+
+&gpi_dma0 {
+	status = "okay";
+};
+
+&gpi_dma1 {
+	status = "okay";
+};
+
+&gpi_dma2 {
+	status = "okay";
+};
+
+/* I2C4 is used, it hosts a Samsung touchscreen, but GPI DMA is broken.. */
+
+&i2c5 {
+	clock-frequency = <400000>;
+	status = "okay";
+
+	/* Dialog SLG51000 CMIC @ 75 */
+};
+
+&i2c9 {
+	clock-frequency = <400000>;
+	status = "okay";
+
+	/* NXP SN1X0 NFC @ 28 */
+};
+
+&i2c13 {
+	clock-frequency = <400000>;
+	status = "okay";
+
+	/* Richwave RTC6226 FM Radio Receiver @ 64 */
+};
+
+&i2c14 {
+	clock-frequency = <1000000>;
+	status = "okay";
+
+	cs35l41_l: speaker-amp@40 {
+		compatible = "cirrus,cs35l41";
+		reg = <0x40>;
+		interrupt-parent = <&tlmm>;
+		interrupts = <182 IRQ_TYPE_LEVEL_LOW>;
+		reset-gpios = <&tlmm 183 GPIO_ACTIVE_HIGH>;
+		cirrus,boost-peak-milliamp = <4000>;
+		cirrus,boost-ind-nanohenry = <1000>;
+		cirrus,boost-cap-microfarad = <15>;
+		cirrus,gpio2-src-select = <2>;
+		cirrus,gpio2-output-enable;
+		cirrus,asp-sdout-hiz = <3>;
+		#sound-dai-cells = <1>;
+	};
+
+	cs35l41_r: speaker-amp@41 {
+		compatible = "cirrus,cs35l41";
+		reg = <0x41>;
+		interrupt-parent = <&tlmm>;
+		interrupts = <182 IRQ_TYPE_LEVEL_LOW>;
+		reset-gpios = <&tlmm 183 GPIO_ACTIVE_HIGH>;
+		cirrus,boost-peak-milliamp = <4000>;
+		cirrus,boost-ind-nanohenry = <1000>;
+		cirrus,boost-cap-microfarad = <15>;
+		cirrus,gpio2-src-select = <2>;
+		cirrus,gpio2-output-enable;
+		cirrus,asp-sdout-hiz = <3>;
+		#sound-dai-cells = <1>;
+	};
+};
+
+&i2c15 {
+	clock-frequency = <400000>;
+	status = "okay";
+
+	/* AMS TCS3490 RGB+IR color sensor @ 72 */
+};
+
+&i2c19 {
+	clock-frequency = <1000000>;
+	status = "okay";
+
+	/* Cirrus Logic CS40L25A boosted haptics driver @ 40 */
+};
+
+&pcie0 {
+	max-link-speed = <2>;
+	status = "okay";
+};
+
+&pcie0_phy {
+	vdda-phy-supply = <&pm8350_l5>;
+	vdda-pll-supply = <&pm8350_l6>;
+	status = "okay";
+};
+
+&remoteproc_adsp {
+	firmware-name = "qcom/adsp.mbn";
+	status = "okay";
+};
+
+&remoteproc_cdsp {
+	firmware-name = "qcom/cdsp.mbn";
+	status = "okay";
+};
+
+&remoteproc_slpi {
+	firmware-name = "qcom/slpi.mbn";
+	status = "okay";
+};
+
+&qupv3_id_0 {
+	status = "okay";
+};
+
+&qupv3_id_1 {
+	status = "okay";
+};
+
+&qupv3_id_2 {
+	status = "okay";
+};
+
+&sdhc_2 {
+	cd-gpios = <&tlmm 92 GPIO_ACTIVE_HIGH>;
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&sdc2_default_state &sdc2_card_det_n>;
+	pinctrl-1 = <&sdc2_sleep_state &sdc2_card_det_n>;
+	vmmc-supply = <&pm8350c_l9>;
+	vqmmc-supply = <&pm8350c_l6>;
+	/* Forbid SDR104/SDR50 - broken hw! */
+	sdhci-caps-mask = <0x3 0x0>;
+	no-sdio;
+	no-mmc;
+	status = "okay";
+};
+
+&spi10 {
+	status = "okay";
+
+	/* NXP SN1X0 NFC Secure Element @ 0 */
+};
+
+&tlmm {
+	gpio-reserved-ranges = <28 4>;
+
+	sdc2_default_state: sdc2-default-state {
+		clk-pins {
+			pins = "sdc2_clk";
+			drive-strength = <16>;
+			bias-disable;
+		};
+
+		cmd-pins {
+			pins = "sdc2_cmd";
+			drive-strength = <16>;
+			bias-pull-up;
+		};
+
+		data-pins {
+			pins = "sdc2_data";
+			drive-strength = <16>;
+			bias-pull-up;
+		};
+	};
+
+	ts_int_default: ts-int-default-state {
+		pins = "gpio23";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+		input-enable;
+	};
+
+	sdc2_card_det_n: sd-card-det-n-state {
+		pins = "gpio92";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-up;
+	};
+};
+
+&uart7 {
+	status = "okay";
+};
+
+&usb_1 {
+	status = "okay";
+};
+
+&usb_1_dwc3 {
+	dr_mode = "peripheral";
+};
+
+&usb_1_hsphy {
+	vdda-pll-supply = <&pm8350_l5>;
+	vdda18-supply = <&pm8350c_l1>;
+	vdda33-supply = <&pm8350_l2>;
+	status = "okay";
+};
+
+&usb_1_qmpphy {
+	vdda-phy-supply = <&pm8350_l6>;
+	vdda-pll-supply = <&pm8350_l1>;
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/qcom/sm8450.dtsi b/arch/arm64/boot/dts/qcom/sm8450.dtsi
new file mode 100644
index 000000000000..d32f08df743d
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sm8450.dtsi
@@ -0,0 +1,4119 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, Linaro Limited
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/qcom,gcc-sm8450.h>
+#include <dt-bindings/clock/qcom,rpmh.h>
+#include <dt-bindings/clock/qcom,sm8450-camcc.h>
+#include <dt-bindings/dma/qcom-gpi.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/mailbox/qcom-ipcc.h>
+#include <dt-bindings/power/qcom-rpmpd.h>
+#include <dt-bindings/interconnect/qcom,sm8450.h>
+#include <dt-bindings/soc/qcom,rpmh-rsc.h>
+#include <dt-bindings/thermal/thermal.h>
+
+/ {
+	interrupt-parent = <&intc>;
+
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	chosen { };
+
+	clocks {
+		xo_board: xo-board {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <76800000>;
+		};
+
+		sleep_clk: sleep-clk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <32000>;
+		};
+	};
+
+	cpus {
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		CPU0: cpu@0 {
+			device_type = "cpu";
+			compatible = "qcom,kryo780";
+			reg = <0x0 0x0>;
+			enable-method = "psci";
+			next-level-cache = <&L2_0>;
+			power-domains = <&CPU_PD0>;
+			power-domain-names = "psci";
+			qcom,freq-domain = <&cpufreq_hw 0>;
+			#cooling-cells = <2>;
+			L2_0: l2-cache {
+			      compatible = "cache";
+			      next-level-cache = <&L3_0>;
+				L3_0: l3-cache {
+				      compatible = "cache";
+				};
+			};
+		};
+
+		CPU1: cpu@100 {
+			device_type = "cpu";
+			compatible = "qcom,kryo780";
+			reg = <0x0 0x100>;
+			enable-method = "psci";
+			next-level-cache = <&L2_100>;
+			power-domains = <&CPU_PD1>;
+			power-domain-names = "psci";
+			qcom,freq-domain = <&cpufreq_hw 0>;
+			#cooling-cells = <2>;
+			L2_100: l2-cache {
+			      compatible = "cache";
+			      next-level-cache = <&L3_0>;
+			};
+		};
+
+		CPU2: cpu@200 {
+			device_type = "cpu";
+			compatible = "qcom,kryo780";
+			reg = <0x0 0x200>;
+			enable-method = "psci";
+			next-level-cache = <&L2_200>;
+			power-domains = <&CPU_PD2>;
+			power-domain-names = "psci";
+			qcom,freq-domain = <&cpufreq_hw 0>;
+			#cooling-cells = <2>;
+			L2_200: l2-cache {
+			      compatible = "cache";
+			      next-level-cache = <&L3_0>;
+			};
+		};
+
+		CPU3: cpu@300 {
+			device_type = "cpu";
+			compatible = "qcom,kryo780";
+			reg = <0x0 0x300>;
+			enable-method = "psci";
+			next-level-cache = <&L2_300>;
+			power-domains = <&CPU_PD3>;
+			power-domain-names = "psci";
+			qcom,freq-domain = <&cpufreq_hw 0>;
+			#cooling-cells = <2>;
+			L2_300: l2-cache {
+			      compatible = "cache";
+			      next-level-cache = <&L3_0>;
+			};
+		};
+
+		CPU4: cpu@400 {
+			device_type = "cpu";
+			compatible = "qcom,kryo780";
+			reg = <0x0 0x400>;
+			enable-method = "psci";
+			next-level-cache = <&L2_400>;
+			power-domains = <&CPU_PD4>;
+			power-domain-names = "psci";
+			qcom,freq-domain = <&cpufreq_hw 1>;
+			#cooling-cells = <2>;
+			L2_400: l2-cache {
+			      compatible = "cache";
+			      next-level-cache = <&L3_0>;
+			};
+		};
+
+		CPU5: cpu@500 {
+			device_type = "cpu";
+			compatible = "qcom,kryo780";
+			reg = <0x0 0x500>;
+			enable-method = "psci";
+			next-level-cache = <&L2_500>;
+			power-domains = <&CPU_PD5>;
+			power-domain-names = "psci";
+			qcom,freq-domain = <&cpufreq_hw 1>;
+			#cooling-cells = <2>;
+			L2_500: l2-cache {
+			      compatible = "cache";
+			      next-level-cache = <&L3_0>;
+			};
+
+		};
+
+		CPU6: cpu@600 {
+			device_type = "cpu";
+			compatible = "qcom,kryo780";
+			reg = <0x0 0x600>;
+			enable-method = "psci";
+			next-level-cache = <&L2_600>;
+			power-domains = <&CPU_PD6>;
+			power-domain-names = "psci";
+			qcom,freq-domain = <&cpufreq_hw 1>;
+			#cooling-cells = <2>;
+			L2_600: l2-cache {
+			      compatible = "cache";
+			      next-level-cache = <&L3_0>;
+			};
+		};
+
+		CPU7: cpu@700 {
+			device_type = "cpu";
+			compatible = "qcom,kryo780";
+			reg = <0x0 0x700>;
+			enable-method = "psci";
+			next-level-cache = <&L2_700>;
+			power-domains = <&CPU_PD7>;
+			power-domain-names = "psci";
+			qcom,freq-domain = <&cpufreq_hw 2>;
+			#cooling-cells = <2>;
+			L2_700: l2-cache {
+			      compatible = "cache";
+			      next-level-cache = <&L3_0>;
+			};
+		};
+
+		cpu-map {
+			cluster0 {
+				core0 {
+					cpu = <&CPU0>;
+				};
+
+				core1 {
+					cpu = <&CPU1>;
+				};
+
+				core2 {
+					cpu = <&CPU2>;
+				};
+
+				core3 {
+					cpu = <&CPU3>;
+				};
+
+				core4 {
+					cpu = <&CPU4>;
+				};
+
+				core5 {
+					cpu = <&CPU5>;
+				};
+
+				core6 {
+					cpu = <&CPU6>;
+				};
+
+				core7 {
+					cpu = <&CPU7>;
+				};
+			};
+		};
+
+		idle-states {
+			entry-method = "psci";
+
+			LITTLE_CPU_SLEEP_0: cpu-sleep-0-0 {
+				compatible = "arm,idle-state";
+				idle-state-name = "silver-rail-power-collapse";
+				arm,psci-suspend-param = <0x40000004>;
+				entry-latency-us = <800>;
+				exit-latency-us = <750>;
+				min-residency-us = <4090>;
+				local-timer-stop;
+			};
+
+			BIG_CPU_SLEEP_0: cpu-sleep-1-0 {
+				compatible = "arm,idle-state";
+				idle-state-name = "gold-rail-power-collapse";
+				arm,psci-suspend-param = <0x40000004>;
+				entry-latency-us = <600>;
+				exit-latency-us = <1550>;
+				min-residency-us = <4791>;
+				local-timer-stop;
+			};
+		};
+
+		domain-idle-states {
+			CLUSTER_SLEEP_0: cluster-sleep-0 {
+				compatible = "domain-idle-state";
+				idle-state-name = "cluster-l3-off";
+				arm,psci-suspend-param = <0x41000044>;
+				entry-latency-us = <1050>;
+				exit-latency-us = <2500>;
+				min-residency-us = <5309>;
+				local-timer-stop;
+			};
+
+			CLUSTER_SLEEP_1: cluster-sleep-1 {
+				compatible = "domain-idle-state";
+				idle-state-name = "cluster-power-collapse";
+				arm,psci-suspend-param = <0x4100c344>;
+				entry-latency-us = <2700>;
+				exit-latency-us = <3500>;
+				min-residency-us = <13959>;
+				local-timer-stop;
+			};
+		};
+	};
+
+	firmware {
+		scm: scm {
+			compatible = "qcom,scm-sm8450", "qcom,scm";
+			interconnects = <&aggre2_noc MASTER_CRYPTO 0 &mc_virt SLAVE_EBI1 0>;
+			#reset-cells = <1>;
+		};
+	};
+
+	clk_virt: interconnect-0 {
+		compatible = "qcom,sm8450-clk-virt";
+		#interconnect-cells = <2>;
+		qcom,bcm-voters = <&apps_bcm_voter>;
+	};
+
+	mc_virt: interconnect-1 {
+		compatible = "qcom,sm8450-mc-virt";
+		#interconnect-cells = <2>;
+		qcom,bcm-voters = <&apps_bcm_voter>;
+	};
+
+	memory@a0000000 {
+		device_type = "memory";
+		/* We expect the bootloader to fill in the size */
+		reg = <0x0 0xa0000000 0x0 0x0>;
+	};
+
+	pmu {
+		compatible = "arm,armv8-pmuv3";
+		interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
+	psci {
+		compatible = "arm,psci-1.0";
+		method = "smc";
+
+		CPU_PD0: cpu0 {
+			#power-domain-cells = <0>;
+			power-domains = <&CLUSTER_PD>;
+			domain-idle-states = <&LITTLE_CPU_SLEEP_0>;
+		};
+
+		CPU_PD1: cpu1 {
+			#power-domain-cells = <0>;
+			power-domains = <&CLUSTER_PD>;
+			domain-idle-states = <&LITTLE_CPU_SLEEP_0>;
+		};
+
+		CPU_PD2: cpu2 {
+			#power-domain-cells = <0>;
+			power-domains = <&CLUSTER_PD>;
+			domain-idle-states = <&LITTLE_CPU_SLEEP_0>;
+		};
+
+		CPU_PD3: cpu3 {
+			#power-domain-cells = <0>;
+			power-domains = <&CLUSTER_PD>;
+			domain-idle-states = <&LITTLE_CPU_SLEEP_0>;
+		};
+
+		CPU_PD4: cpu4 {
+			#power-domain-cells = <0>;
+			power-domains = <&CLUSTER_PD>;
+			domain-idle-states = <&BIG_CPU_SLEEP_0>;
+		};
+
+		CPU_PD5: cpu5 {
+			#power-domain-cells = <0>;
+			power-domains = <&CLUSTER_PD>;
+			domain-idle-states = <&BIG_CPU_SLEEP_0>;
+		};
+
+		CPU_PD6: cpu6 {
+			#power-domain-cells = <0>;
+			power-domains = <&CLUSTER_PD>;
+			domain-idle-states = <&BIG_CPU_SLEEP_0>;
+		};
+
+		CPU_PD7: cpu7 {
+			#power-domain-cells = <0>;
+			power-domains = <&CLUSTER_PD>;
+			domain-idle-states = <&BIG_CPU_SLEEP_0>;
+		};
+
+		CLUSTER_PD: cpu-cluster0 {
+			#power-domain-cells = <0>;
+			domain-idle-states = <&CLUSTER_SLEEP_0>, <&CLUSTER_SLEEP_1>;
+		};
+	};
+
+	qup_opp_table_100mhz: opp-table-qup {
+		compatible = "operating-points-v2";
+
+		opp-50000000 {
+			opp-hz = /bits/ 64 <50000000>;
+			required-opps = <&rpmhpd_opp_min_svs>;
+		};
+
+		opp-75000000 {
+			opp-hz = /bits/ 64 <75000000>;
+			required-opps = <&rpmhpd_opp_low_svs>;
+		};
+
+		opp-100000000 {
+			opp-hz = /bits/ 64 <100000000>;
+			required-opps = <&rpmhpd_opp_svs>;
+		};
+	};
+
+	reserved_memory: reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		hyp_mem: memory@80000000 {
+			reg = <0x0 0x80000000 0x0 0x600000>;
+			no-map;
+		};
+
+		xbl_dt_log_mem: memory@80600000 {
+			reg = <0x0 0x80600000 0x0 0x40000>;
+			no-map;
+		};
+
+		xbl_ramdump_mem: memory@80640000 {
+			reg = <0x0 0x80640000 0x0 0x180000>;
+			no-map;
+		};
+
+		xbl_sc_mem: memory@807c0000 {
+			reg = <0x0 0x807c0000 0x0 0x40000>;
+			no-map;
+		};
+
+		aop_image_mem: memory@80800000 {
+			reg = <0x0 0x80800000 0x0 0x60000>;
+			no-map;
+		};
+
+		aop_cmd_db_mem: memory@80860000 {
+			compatible = "qcom,cmd-db";
+			reg = <0x0 0x80860000 0x0 0x20000>;
+			no-map;
+		};
+
+		aop_config_mem: memory@80880000 {
+			reg = <0x0 0x80880000 0x0 0x20000>;
+			no-map;
+		};
+
+		tme_crash_dump_mem: memory@808a0000 {
+			reg = <0x0 0x808a0000 0x0 0x40000>;
+			no-map;
+		};
+
+		tme_log_mem: memory@808e0000 {
+			reg = <0x0 0x808e0000 0x0 0x4000>;
+			no-map;
+		};
+
+		uefi_log_mem: memory@808e4000 {
+			reg = <0x0 0x808e4000 0x0 0x10000>;
+			no-map;
+		};
+
+		/* secdata region can be reused by apps */
+		smem: memory@80900000 {
+			compatible = "qcom,smem";
+			reg = <0x0 0x80900000 0x0 0x200000>;
+			hwlocks = <&tcsr_mutex 3>;
+			no-map;
+		};
+
+		cpucp_fw_mem: memory@80b00000 {
+			reg = <0x0 0x80b00000 0x0 0x100000>;
+			no-map;
+		};
+
+		cdsp_secure_heap: memory@80c00000 {
+			reg = <0x0 0x80c00000 0x0 0x4600000>;
+			no-map;
+		};
+
+		video_mem: memory@85700000 {
+			reg = <0x0 0x85700000 0x0 0x700000>;
+			no-map;
+		};
+
+		adsp_mem: memory@85e00000 {
+			reg = <0x0 0x85e00000 0x0 0x2100000>;
+			no-map;
+		};
+
+		slpi_mem: memory@88000000 {
+			reg = <0x0 0x88000000 0x0 0x1900000>;
+			no-map;
+		};
+
+		cdsp_mem: memory@89900000 {
+			reg = <0x0 0x89900000 0x0 0x2000000>;
+			no-map;
+		};
+
+		ipa_fw_mem: memory@8b900000 {
+			reg = <0x0 0x8b900000 0x0 0x10000>;
+			no-map;
+		};
+
+		ipa_gsi_mem: memory@8b910000 {
+			reg = <0x0 0x8b910000 0x0 0xa000>;
+			no-map;
+		};
+
+		gpu_micro_code_mem: memory@8b91a000 {
+			reg = <0x0 0x8b91a000 0x0 0x2000>;
+			no-map;
+		};
+
+		spss_region_mem: memory@8ba00000 {
+			reg = <0x0 0x8ba00000 0x0 0x180000>;
+			no-map;
+		};
+
+		/* First part of the "SPU secure shared memory" region */
+		spu_tz_shared_mem: memory@8bb80000 {
+			reg = <0x0 0x8bb80000 0x0 0x60000>;
+			no-map;
+		};
+
+		/* Second part of the "SPU secure shared memory" region */
+		spu_modem_shared_mem: memory@8bbe0000 {
+			reg = <0x0 0x8bbe0000 0x0 0x20000>;
+			no-map;
+		};
+
+		mpss_mem: memory@8bc00000 {
+			reg = <0x0 0x8bc00000 0x0 0x13200000>;
+			no-map;
+		};
+
+		cvp_mem: memory@9ee00000 {
+			reg = <0x0 0x9ee00000 0x0 0x700000>;
+			no-map;
+		};
+
+		camera_mem: memory@9f500000 {
+			reg = <0x0 0x9f500000 0x0 0x800000>;
+			no-map;
+		};
+
+		rmtfs_mem: memory@9fd00000 {
+			compatible = "qcom,rmtfs-mem";
+			reg = <0x0 0x9fd00000 0x0 0x280000>;
+			no-map;
+
+			qcom,client-id = <1>;
+			qcom,vmid = <15>;
+		};
+
+		xbl_sc_mem2: memory@a6e00000 {
+			reg = <0x0 0xa6e00000 0x0 0x40000>;
+			no-map;
+		};
+
+		global_sync_mem: memory@a6f00000 {
+			reg = <0x0 0xa6f00000 0x0 0x100000>;
+			no-map;
+		};
+
+		/* uefi region can be reused by APPS */
+
+		/* Linux kernel image is loaded at 0xa0000000 */
+
+		oem_vm_mem: memory@bb000000 {
+			reg = <0x0 0xbb000000 0x0 0x5000000>;
+			no-map;
+		};
+
+		mte_mem: memory@c0000000 {
+			reg = <0x0 0xc0000000 0x0 0x20000000>;
+			no-map;
+		};
+
+		qheebsp_reserved_mem: memory@e0000000 {
+			reg = <0x0 0xe0000000 0x0 0x600000>;
+			no-map;
+		};
+
+		cpusys_vm_mem: memory@e0600000 {
+			reg = <0x0 0xe0600000 0x0 0x400000>;
+			no-map;
+		};
+
+		hyp_reserved_mem: memory@e0a00000 {
+			reg = <0x0 0xe0a00000 0x0 0x100000>;
+			no-map;
+		};
+
+		trust_ui_vm_mem: memory@e0b00000 {
+			reg = <0x0 0xe0b00000 0x0 0x4af3000>;
+			no-map;
+		};
+
+		trust_ui_vm_qrtr: memory@e55f3000 {
+			reg = <0x0 0xe55f3000 0x0 0x9000>;
+			no-map;
+		};
+
+		trust_ui_vm_vblk0_ring: memory@e55fc000 {
+			reg = <0x0 0xe55fc000 0x0 0x4000>;
+			no-map;
+		};
+
+		trust_ui_vm_swiotlb: memory@e5600000 {
+			reg = <0x0 0xe5600000 0x0 0x100000>;
+			no-map;
+		};
+
+		tz_stat_mem: memory@e8800000 {
+			reg = <0x0 0xe8800000 0x0 0x100000>;
+			no-map;
+		};
+
+		tags_mem: memory@e8900000 {
+			reg = <0x0 0xe8900000 0x0 0x1200000>;
+			no-map;
+		};
+
+		qtee_mem: memory@e9b00000 {
+			reg = <0x0 0xe9b00000 0x0 0x500000>;
+			no-map;
+		};
+
+		trusted_apps_mem: memory@ea000000 {
+			reg = <0x0 0xea000000 0x0 0x3900000>;
+			no-map;
+		};
+
+		trusted_apps_ext_mem: memory@ed900000 {
+			reg = <0x0 0xed900000 0x0 0x3b00000>;
+			no-map;
+		};
+	};
+
+	smp2p-adsp {
+		compatible = "qcom,smp2p";
+		qcom,smem = <443>, <429>;
+		interrupts-extended = <&ipcc IPCC_CLIENT_LPASS
+					     IPCC_MPROC_SIGNAL_SMP2P
+					     IRQ_TYPE_EDGE_RISING>;
+		mboxes = <&ipcc IPCC_CLIENT_LPASS
+				IPCC_MPROC_SIGNAL_SMP2P>;
+
+		qcom,local-pid = <0>;
+		qcom,remote-pid = <2>;
+
+		smp2p_adsp_out: master-kernel {
+			qcom,entry-name = "master-kernel";
+			#qcom,smem-state-cells = <1>;
+		};
+
+		smp2p_adsp_in: slave-kernel {
+			qcom,entry-name = "slave-kernel";
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	smp2p-cdsp {
+		compatible = "qcom,smp2p";
+		qcom,smem = <94>, <432>;
+		interrupts-extended = <&ipcc IPCC_CLIENT_CDSP
+					     IPCC_MPROC_SIGNAL_SMP2P
+					     IRQ_TYPE_EDGE_RISING>;
+		mboxes = <&ipcc IPCC_CLIENT_CDSP
+				IPCC_MPROC_SIGNAL_SMP2P>;
+
+		qcom,local-pid = <0>;
+		qcom,remote-pid = <5>;
+
+		smp2p_cdsp_out: master-kernel {
+			qcom,entry-name = "master-kernel";
+			#qcom,smem-state-cells = <1>;
+		};
+
+		smp2p_cdsp_in: slave-kernel {
+			qcom,entry-name = "slave-kernel";
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	smp2p-modem {
+		compatible = "qcom,smp2p";
+		qcom,smem = <435>, <428>;
+		interrupts-extended = <&ipcc IPCC_CLIENT_MPSS
+					     IPCC_MPROC_SIGNAL_SMP2P
+					     IRQ_TYPE_EDGE_RISING>;
+		mboxes = <&ipcc IPCC_CLIENT_MPSS
+				IPCC_MPROC_SIGNAL_SMP2P>;
+
+		qcom,local-pid = <0>;
+		qcom,remote-pid = <1>;
+
+		smp2p_modem_out: master-kernel {
+			qcom,entry-name = "master-kernel";
+			#qcom,smem-state-cells = <1>;
+		};
+
+		smp2p_modem_in: slave-kernel {
+			qcom,entry-name = "slave-kernel";
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		ipa_smp2p_out: ipa-ap-to-modem {
+			qcom,entry-name = "ipa";
+			#qcom,smem-state-cells = <1>;
+		};
+
+		ipa_smp2p_in: ipa-modem-to-ap {
+			qcom,entry-name = "ipa";
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	smp2p-slpi {
+		compatible = "qcom,smp2p";
+		qcom,smem = <481>, <430>;
+		interrupts-extended = <&ipcc IPCC_CLIENT_SLPI
+					     IPCC_MPROC_SIGNAL_SMP2P
+					     IRQ_TYPE_EDGE_RISING>;
+		mboxes = <&ipcc IPCC_CLIENT_SLPI
+				IPCC_MPROC_SIGNAL_SMP2P>;
+
+		qcom,local-pid = <0>;
+		qcom,remote-pid = <3>;
+
+		smp2p_slpi_out: master-kernel {
+			qcom,entry-name = "master-kernel";
+			#qcom,smem-state-cells = <1>;
+		};
+
+		smp2p_slpi_in: slave-kernel {
+			qcom,entry-name = "slave-kernel";
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	soc: soc@0 {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges = <0 0 0 0 0x10 0>;
+		dma-ranges = <0 0 0 0 0x10 0>;
+		compatible = "simple-bus";
+
+		gcc: clock-controller@100000 {
+			compatible = "qcom,gcc-sm8450";
+			reg = <0x0 0x00100000 0x0 0x1f4200>;
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+			#power-domain-cells = <1>;
+			clocks = <&rpmhcc RPMH_CXO_CLK>,
+				 <&pcie0_lane>,
+				 <&pcie1_lane>,
+				 <&sleep_clk>;
+			clock-names = "bi_tcxo",
+				      "pcie_0_pipe_clk",
+				      "pcie_1_pipe_clk",
+				      "sleep_clk";
+		};
+
+		gpi_dma2: dma-controller@800000 {
+			compatible = "qcom,sm8450-gpi-dma";
+			#dma-cells = <3>;
+			reg = <0 0x800000 0 0x60000>;
+			interrupts = <GIC_SPI 588 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 589 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 590 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 591 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 592 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 593 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 594 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 595 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 596 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 597 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 598 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 599 IRQ_TYPE_LEVEL_HIGH>;
+			dma-channels = <12>;
+			dma-channel-mask = <0x7e>;
+			iommus = <&apps_smmu 0x496 0x0>;
+			status = "disabled";
+		};
+
+		qupv3_id_2: geniqup@8c0000 {
+			compatible = "qcom,geni-se-qup";
+			reg = <0x0 0x008c0000 0x0 0x2000>;
+			clock-names = "m-ahb", "s-ahb";
+			clocks = <&gcc GCC_QUPV3_WRAP_2_M_AHB_CLK>,
+				 <&gcc GCC_QUPV3_WRAP_2_S_AHB_CLK>;
+			iommus = <&apps_smmu 0x483 0x0>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+			status = "disabled";
+
+			i2c15: i2c@880000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0x0 0x00880000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP2_S0_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c15_data_clk>;
+				interrupts = <GIC_SPI 373 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+						<&aggre2_noc MASTER_QUP_2 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma2 0 0 QCOM_GPI_I2C>,
+				       <&gpi_dma2 1 0 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				status = "disabled";
+			};
+
+			spi15: spi@880000 {
+				compatible = "qcom,geni-spi";
+				reg = <0x0 0x00880000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP2_S0_CLK>;
+				interrupts = <GIC_SPI 373 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi15_data_clk>, <&qup_spi15_cs>;
+				spi-max-frequency = <50000000>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>;
+				interconnect-names = "qup-core", "qup-config";
+				dmas = <&gpi_dma2 0 0 QCOM_GPI_SPI>,
+				       <&gpi_dma2 1 0 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			i2c16: i2c@884000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0x0 0x00884000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP2_S1_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c16_data_clk>;
+				interrupts = <GIC_SPI 583 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+						<&aggre2_noc MASTER_QUP_2 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma2 0 1 QCOM_GPI_I2C>,
+				       <&gpi_dma2 1 1 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				status = "disabled";
+			};
+
+			spi16: spi@884000 {
+				compatible = "qcom,geni-spi";
+				reg = <0x0 0x00884000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP2_S1_CLK>;
+				interrupts = <GIC_SPI 583 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi16_data_clk>, <&qup_spi16_cs>;
+				spi-max-frequency = <50000000>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>;
+				interconnect-names = "qup-core", "qup-config";
+				dmas = <&gpi_dma2 0 1 QCOM_GPI_SPI>,
+				       <&gpi_dma2 1 1 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			i2c17: i2c@888000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0x0 0x00888000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP2_S2_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c17_data_clk>;
+				interrupts = <GIC_SPI 584 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+						<&aggre2_noc MASTER_QUP_2 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma2 0 2 QCOM_GPI_I2C>,
+				       <&gpi_dma2 1 2 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				status = "disabled";
+			};
+
+			spi17: spi@888000 {
+				compatible = "qcom,geni-spi";
+				reg = <0x0 0x00888000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP2_S2_CLK>;
+				interrupts = <GIC_SPI 584 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi17_data_clk>, <&qup_spi17_cs>;
+				spi-max-frequency = <50000000>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>;
+				interconnect-names = "qup-core", "qup-config";
+				dmas = <&gpi_dma2 0 2 QCOM_GPI_SPI>,
+				       <&gpi_dma2 1 2 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			i2c18: i2c@88c000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0x0 0x0088c000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP2_S3_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c18_data_clk>;
+				interrupts = <GIC_SPI 585 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+						<&aggre2_noc MASTER_QUP_2 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma2 0 3 QCOM_GPI_I2C>,
+				       <&gpi_dma2 1 3 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				status = "disabled";
+			};
+
+			spi18: spi@88c000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x0088c000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP2_S3_CLK>;
+				interrupts = <GIC_SPI 585 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi18_data_clk>, <&qup_spi18_cs>;
+				spi-max-frequency = <50000000>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>;
+				interconnect-names = "qup-core", "qup-config";
+				dmas = <&gpi_dma2 0 3 QCOM_GPI_I2C>,
+				       <&gpi_dma2 1 3 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			i2c19: i2c@890000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0x0 0x00890000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP2_S4_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c19_data_clk>;
+				interrupts = <GIC_SPI 586 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+						<&aggre2_noc MASTER_QUP_2 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma2 0 4 QCOM_GPI_I2C>,
+				       <&gpi_dma2 1 4 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				status = "disabled";
+			};
+
+			spi19: spi@890000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00890000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP2_S4_CLK>;
+				interrupts = <GIC_SPI 586 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi19_data_clk>, <&qup_spi19_cs>;
+				spi-max-frequency = <50000000>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>;
+				interconnect-names = "qup-core", "qup-config";
+				dmas = <&gpi_dma2 0 4 QCOM_GPI_I2C>,
+				       <&gpi_dma2 1 4 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			i2c20: i2c@894000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0x0 0x00894000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP2_S5_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c20_data_clk>;
+				interrupts = <GIC_SPI 587 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+						<&aggre2_noc MASTER_QUP_2 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma2 0 5 QCOM_GPI_I2C>,
+				       <&gpi_dma2 1 5 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				status = "disabled";
+			};
+
+			uart20: serial@894000 {
+				compatible = "qcom,geni-uart";
+				reg = <0 0x00894000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP2_S5_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_uart20_default>;
+				interrupts = <GIC_SPI 587 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			spi20: spi@894000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00894000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP2_S5_CLK>;
+				interrupts = <GIC_SPI 587 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi20_data_clk>, <&qup_spi20_cs>;
+				spi-max-frequency = <50000000>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>;
+				interconnect-names = "qup-core", "qup-config";
+				dmas = <&gpi_dma2 0 5 QCOM_GPI_SPI>,
+				       <&gpi_dma2 1 5 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			i2c21: i2c@898000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0x0 0x00898000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP2_S6_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c21_data_clk>;
+				interrupts = <GIC_SPI 579 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+						<&aggre2_noc MASTER_QUP_2 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma2 0 6 QCOM_GPI_I2C>,
+				       <&gpi_dma2 1 6 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				status = "disabled";
+			};
+
+			spi21: spi@898000 {
+				compatible = "qcom,geni-spi";
+				reg = <0 0x00898000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP2_S6_CLK>;
+				interrupts = <GIC_SPI 579 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi21_data_clk>, <&qup_spi21_cs>;
+				spi-max-frequency = <50000000>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_2 0 &clk_virt SLAVE_QUP_CORE_2 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>;
+				interconnect-names = "qup-core", "qup-config";
+				dmas = <&gpi_dma2 0 6 QCOM_GPI_SPI>,
+				       <&gpi_dma2 1 6 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+		};
+
+		gpi_dma0: dma-controller@900000 {
+			compatible = "qcom,sm8450-gpi-dma";
+			#dma-cells = <3>;
+			reg = <0 0x900000 0 0x60000>;
+			interrupts = <GIC_SPI 244 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 245 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 246 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 247 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 248 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 249 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 250 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 251 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 252 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 253 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 254 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 255 IRQ_TYPE_LEVEL_HIGH>;
+			dma-channels = <12>;
+			dma-channel-mask = <0x7e>;
+			iommus = <&apps_smmu 0x5b6 0x0>;
+			status = "disabled";
+		};
+
+		qupv3_id_0: geniqup@9c0000 {
+			compatible = "qcom,geni-se-qup";
+			reg = <0x0 0x009c0000 0x0 0x2000>;
+			clock-names = "m-ahb", "s-ahb";
+			clocks = <&gcc GCC_QUPV3_WRAP_0_M_AHB_CLK>,
+				 <&gcc GCC_QUPV3_WRAP_0_S_AHB_CLK>;
+			iommus = <&apps_smmu 0x5a3 0x0>;
+			interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>;
+			interconnect-names = "qup-core";
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+			status = "disabled";
+
+			i2c0: i2c@980000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0x0 0x00980000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c0_data_clk>;
+				interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+						<&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma0 0 0 QCOM_GPI_I2C>,
+				       <&gpi_dma0 1 0 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				status = "disabled";
+			};
+
+			spi0: spi@980000 {
+				compatible = "qcom,geni-spi";
+				reg = <0x0 0x00980000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>;
+				interrupts = <GIC_SPI 601 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi0_data_clk>, <&qup_spi0_cs>;
+				power-domains = <&rpmhpd SM8450_CX>;
+				operating-points-v2 = <&qup_opp_table_100mhz>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+						<&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma0 0 0 QCOM_GPI_SPI>,
+				       <&gpi_dma0 1 0 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			i2c1: i2c@984000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0x0 0x00984000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c1_data_clk>;
+				interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+						<&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma0 0 1 QCOM_GPI_I2C>,
+				       <&gpi_dma0 1 1 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				status = "disabled";
+			};
+
+			spi1: spi@984000 {
+				compatible = "qcom,geni-spi";
+				reg = <0x0 0x00984000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>;
+				interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi1_data_clk>, <&qup_spi1_cs>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+						<&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma0 0 1 QCOM_GPI_SPI>,
+				       <&gpi_dma0 1 1 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			i2c2: i2c@988000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0x0 0x00988000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c2_data_clk>;
+				interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+						<&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma0 0 2 QCOM_GPI_I2C>,
+				       <&gpi_dma0 1 2 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				status = "disabled";
+			};
+
+			spi2: spi@988000 {
+				compatible = "qcom,geni-spi";
+				reg = <0x0 0x00988000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>;
+				interrupts = <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi2_data_clk>, <&qup_spi2_cs>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+						<&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma0 0 2 QCOM_GPI_SPI>,
+				       <&gpi_dma0 1 2 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+
+			i2c3: i2c@98c000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0x0 0x0098c000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c3_data_clk>;
+				interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+						<&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma0 0 3 QCOM_GPI_I2C>,
+				       <&gpi_dma0 1 3 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				status = "disabled";
+			};
+
+			spi3: spi@98c000 {
+				compatible = "qcom,geni-spi";
+				reg = <0x0 0x0098c000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>;
+				interrupts = <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi3_data_clk>, <&qup_spi3_cs>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+						<&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma0 0 3 QCOM_GPI_SPI>,
+				       <&gpi_dma0 1 3 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			i2c4: i2c@990000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0x0 0x00990000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c4_data_clk>;
+				interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+						<&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma0 0 4 QCOM_GPI_I2C>,
+				       <&gpi_dma0 1 4 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				status = "disabled";
+			};
+
+			spi4: spi@990000 {
+				compatible = "qcom,geni-spi";
+				reg = <0x0 0x00990000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
+				interrupts = <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi4_data_clk>, <&qup_spi4_cs>;
+				power-domains = <&rpmhpd SM8450_CX>;
+				operating-points-v2 = <&qup_opp_table_100mhz>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+						<&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma0 0 4 QCOM_GPI_SPI>,
+				       <&gpi_dma0 1 4 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			i2c5: i2c@994000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0x0 0x00994000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c5_data_clk>;
+				interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+						<&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma0 0 5 QCOM_GPI_I2C>,
+				       <&gpi_dma0 1 5 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				status = "disabled";
+			};
+
+			spi5: spi@994000 {
+				compatible = "qcom,geni-spi";
+				reg = <0x0 0x00994000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>;
+				interrupts = <GIC_SPI 606 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi5_data_clk>, <&qup_spi5_cs>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+						<&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma0 0 5 QCOM_GPI_SPI>,
+				       <&gpi_dma0 1 5 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+
+			i2c6: i2c@998000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0x0 0x998000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c6_data_clk>;
+				interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+						<&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma0 0 6 QCOM_GPI_I2C>,
+				       <&gpi_dma0 1 6 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				status = "disabled";
+			};
+
+			spi6: spi@998000 {
+				compatible = "qcom,geni-spi";
+				reg = <0x0 0x998000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S6_CLK>;
+				interrupts = <GIC_SPI 607 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi6_data_clk>, <&qup_spi6_cs>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_0 0 &clk_virt SLAVE_QUP_CORE_0 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+						<&aggre2_noc MASTER_QUP_0 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma0 0 6 QCOM_GPI_SPI>,
+				       <&gpi_dma0 1 6 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			uart7: serial@99c000 {
+				compatible = "qcom,geni-debug-uart";
+				reg = <0 0x0099c000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP0_S7_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_uart7_tx>, <&qup_uart7_rx>;
+				interrupts = <GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+		};
+
+		gpi_dma1: dma-controller@a00000 {
+			compatible = "qcom,sm8450-gpi-dma";
+			#dma-cells = <3>;
+			reg = <0 0xa00000 0 0x60000>;
+			interrupts = <GIC_SPI 279 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 280 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 281 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 282 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 283 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 284 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 293 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 294 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 295 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 296 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 297 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 298 IRQ_TYPE_LEVEL_HIGH>;
+			dma-channels = <12>;
+			dma-channel-mask = <0x7e>;
+			iommus = <&apps_smmu 0x56 0x0>;
+			status = "disabled";
+		};
+
+		qupv3_id_1: geniqup@ac0000 {
+			compatible = "qcom,geni-se-qup";
+			reg = <0x0 0x00ac0000 0x0 0x6000>;
+			clock-names = "m-ahb", "s-ahb";
+			clocks = <&gcc GCC_QUPV3_WRAP_1_M_AHB_CLK>,
+				 <&gcc GCC_QUPV3_WRAP_1_S_AHB_CLK>;
+			iommus = <&apps_smmu 0x43 0x0>;
+			interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>;
+			interconnect-names = "qup-core";
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+			status = "disabled";
+
+			i2c8: i2c@a80000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0x0 0x00a80000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c8_data_clk>;
+				interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+						<&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma1 0 0 QCOM_GPI_I2C>,
+				       <&gpi_dma1 1 0 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				status = "disabled";
+			};
+
+			spi8: spi@a80000 {
+				compatible = "qcom,geni-spi";
+				reg = <0x0 0x00a80000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S0_CLK>;
+				interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi8_data_clk>, <&qup_spi8_cs>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+						<&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma1 0 0 QCOM_GPI_SPI>,
+				       <&gpi_dma1 1 0 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			i2c9: i2c@a84000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0x0 0x00a84000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c9_data_clk>;
+				interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+						<&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma1 0 1 QCOM_GPI_I2C>,
+				       <&gpi_dma1 1 1 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				status = "disabled";
+			};
+
+			spi9: spi@a84000 {
+				compatible = "qcom,geni-spi";
+				reg = <0x0 0x00a84000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S1_CLK>;
+				interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi9_data_clk>, <&qup_spi9_cs>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+						<&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma1 0 1 QCOM_GPI_SPI>,
+				       <&gpi_dma1 1 1 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			i2c10: i2c@a88000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0x0 0x00a88000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c10_data_clk>;
+				interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+						<&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma1 0 2 QCOM_GPI_I2C>,
+				       <&gpi_dma1 1 2 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				status = "disabled";
+			};
+
+			spi10: spi@a88000 {
+				compatible = "qcom,geni-spi";
+				reg = <0x0 0x00a88000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S2_CLK>;
+				interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi10_data_clk>, <&qup_spi10_cs>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+						<&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma1 0 2 QCOM_GPI_SPI>,
+				       <&gpi_dma1 1 2 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			i2c11: i2c@a8c000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0x0 0x00a8c000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c11_data_clk>;
+				interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+						<&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma1 0 3 QCOM_GPI_I2C>,
+				       <&gpi_dma1 1 3 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				status = "disabled";
+			};
+
+			spi11: spi@a8c000 {
+				compatible = "qcom,geni-spi";
+				reg = <0x0 0x00a8c000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S3_CLK>;
+				interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi11_data_clk>, <&qup_spi11_cs>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+						<&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma1 0 3 QCOM_GPI_SPI>,
+				       <&gpi_dma1 1 3 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			i2c12: i2c@a90000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0x0 0x00a90000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c12_data_clk>;
+				interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+						<&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma1 0 4 QCOM_GPI_I2C>,
+				       <&gpi_dma1 1 4 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				status = "disabled";
+			};
+
+			spi12: spi@a90000 {
+				compatible = "qcom,geni-spi";
+				reg = <0x0 0x00a90000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S4_CLK>;
+				interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi12_data_clk>, <&qup_spi12_cs>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+						<&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma1 0 4 QCOM_GPI_SPI>,
+				       <&gpi_dma1 1 4 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			i2c13: i2c@a94000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00a94000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c13_data_clk>;
+				interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+						<&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma1 0 5 QCOM_GPI_I2C>,
+				       <&gpi_dma1 1 5 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			spi13: spi@a94000 {
+				compatible = "qcom,geni-spi";
+				reg = <0x0 0x00a94000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
+				interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi13_data_clk>, <&qup_spi13_cs>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+						<&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma1 0 5 QCOM_GPI_SPI>,
+				       <&gpi_dma1 1 5 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			i2c14: i2c@a98000 {
+				compatible = "qcom,geni-i2c";
+				reg = <0 0x00a98000 0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S6_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_i2c14_data_clk>;
+				interrupts = <GIC_SPI 363 IRQ_TYPE_LEVEL_HIGH>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+						<&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma1 0 6 QCOM_GPI_I2C>,
+				       <&gpi_dma1 1 6 QCOM_GPI_I2C>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+
+			spi14: spi@a98000 {
+				compatible = "qcom,geni-spi";
+				reg = <0x0 0x00a98000 0x0 0x4000>;
+				clock-names = "se";
+				clocks = <&gcc GCC_QUPV3_WRAP1_S6_CLK>;
+				interrupts = <GIC_SPI 363 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_spi14_data_clk>, <&qup_spi14_cs>;
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 0 &clk_virt SLAVE_QUP_CORE_1 0>,
+						<&system_noc MASTER_A2NOC_SNOC 0 &gem_noc SLAVE_LLCC 0>,
+						<&aggre2_noc MASTER_QUP_1 0 &mc_virt SLAVE_EBI1 0>;
+				interconnect-names = "qup-core", "qup-config", "qup-memory";
+				dmas = <&gpi_dma1 0 6 QCOM_GPI_SPI>,
+				       <&gpi_dma1 1 6 QCOM_GPI_SPI>;
+				dma-names = "tx", "rx";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				status = "disabled";
+			};
+		};
+
+		pcie0: pci@1c00000 {
+			compatible = "qcom,pcie-sm8450-pcie0";
+			reg = <0 0x01c00000 0 0x3000>,
+			      <0 0x60000000 0 0xf1d>,
+			      <0 0x60000f20 0 0xa8>,
+			      <0 0x60001000 0 0x1000>,
+			      <0 0x60100000 0 0x100000>;
+			reg-names = "parf", "dbi", "elbi", "atu", "config";
+			device_type = "pci";
+			linux,pci-domain = <0>;
+			bus-range = <0x00 0xff>;
+			num-lanes = <1>;
+
+			#address-cells = <3>;
+			#size-cells = <2>;
+
+			ranges = <0x01000000 0x0 0x60200000 0 0x60200000 0x0 0x100000>,
+				 <0x02000000 0x0 0x60300000 0 0x60300000 0x0 0x3d00000>;
+
+			interrupts = <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "msi";
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0x7>;
+			interrupt-map = <0 0 0 1 &intc 0 0 0 149 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+					<0 0 0 2 &intc 0 0 0 150 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+					<0 0 0 3 &intc 0 0 0 151 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+					<0 0 0 4 &intc 0 0 0 152 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+
+			clocks = <&gcc GCC_PCIE_0_PIPE_CLK>,
+				 <&gcc GCC_PCIE_0_PIPE_CLK_SRC>,
+				 <&pcie0_lane>,
+				 <&rpmhcc RPMH_CXO_CLK>,
+				 <&gcc GCC_PCIE_0_AUX_CLK>,
+				 <&gcc GCC_PCIE_0_CFG_AHB_CLK>,
+				 <&gcc GCC_PCIE_0_MSTR_AXI_CLK>,
+				 <&gcc GCC_PCIE_0_SLV_AXI_CLK>,
+				 <&gcc GCC_PCIE_0_SLV_Q2A_AXI_CLK>,
+				 <&gcc GCC_DDRSS_PCIE_SF_TBU_CLK>,
+				 <&gcc GCC_AGGRE_NOC_PCIE_0_AXI_CLK>,
+				 <&gcc GCC_AGGRE_NOC_PCIE_1_AXI_CLK>;
+			clock-names = "pipe",
+				      "pipe_mux",
+				      "phy_pipe",
+				      "ref",
+				      "aux",
+				      "cfg",
+				      "bus_master",
+				      "bus_slave",
+				      "slave_q2a",
+				      "ddrss_sf_tbu",
+				      "aggre0",
+				      "aggre1";
+
+			iommus = <&apps_smmu 0x1c00 0x7f>;
+			iommu-map = <0x0   &apps_smmu 0x1c00 0x1>,
+				    <0x100 &apps_smmu 0x1c01 0x1>;
+
+			resets = <&gcc GCC_PCIE_0_BCR>;
+			reset-names = "pci";
+
+			power-domains = <&gcc PCIE_0_GDSC>;
+			power-domain-names = "gdsc";
+
+			phys = <&pcie0_lane>;
+			phy-names = "pciephy";
+
+			perst-gpios = <&tlmm 94 GPIO_ACTIVE_LOW>;
+			wake-gpios = <&tlmm 96 GPIO_ACTIVE_HIGH>;
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&pcie0_default_state>;
+
+			status = "disabled";
+		};
+
+		pcie0_phy: phy@1c06000 {
+			compatible = "qcom,sm8450-qmp-gen3x1-pcie-phy";
+			reg = <0 0x01c06000 0 0x200>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+			clocks = <&gcc GCC_PCIE_0_AUX_CLK>,
+				 <&gcc GCC_PCIE_0_CFG_AHB_CLK>,
+				 <&gcc GCC_PCIE_0_CLKREF_EN>,
+				 <&gcc GCC_PCIE_0_PHY_RCHNG_CLK>;
+			clock-names = "aux", "cfg_ahb", "ref", "refgen";
+
+			resets = <&gcc GCC_PCIE_0_PHY_BCR>;
+			reset-names = "phy";
+
+			assigned-clocks = <&gcc GCC_PCIE_0_PHY_RCHNG_CLK>;
+			assigned-clock-rates = <100000000>;
+
+			status = "disabled";
+
+			pcie0_lane: phy@1c06200 {
+				reg = <0 0x1c06e00 0 0x200>, /* tx */
+				      <0 0x1c07000 0 0x200>, /* rx */
+				      <0 0x1c06200 0 0x200>, /* pcs */
+				      <0 0x1c06600 0 0x200>; /* pcs_pcie */
+				clocks = <&gcc GCC_PCIE_0_PIPE_CLK>;
+				clock-names = "pipe0";
+
+				#clock-cells = <0>;
+				#phy-cells = <0>;
+				clock-output-names = "pcie_0_pipe_clk";
+			};
+		};
+
+		pcie1: pci@1c08000 {
+			compatible = "qcom,pcie-sm8450-pcie1";
+			reg = <0 0x01c08000 0 0x3000>,
+			      <0 0x40000000 0 0xf1d>,
+			      <0 0x40000f20 0 0xa8>,
+			      <0 0x40001000 0 0x1000>,
+			      <0 0x40100000 0 0x100000>;
+			reg-names = "parf", "dbi", "elbi", "atu", "config";
+			device_type = "pci";
+			linux,pci-domain = <1>;
+			bus-range = <0x00 0xff>;
+			num-lanes = <2>;
+
+			#address-cells = <3>;
+			#size-cells = <2>;
+
+			ranges = <0x01000000 0x0 0x40200000 0 0x40200000 0x0 0x100000>,
+				 <0x02000000 0x0 0x40300000 0 0x40300000 0x0 0x1fd00000>;
+
+			interrupts = <GIC_SPI 307 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "msi";
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0x7>;
+			interrupt-map = <0 0 0 1 &intc 0 0 0 434 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+					<0 0 0 2 &intc 0 0 0 435 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+					<0 0 0 3 &intc 0 0 0 438 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+					<0 0 0 4 &intc 0 0 0 439 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+
+			clocks = <&gcc GCC_PCIE_1_PIPE_CLK>,
+				 <&gcc GCC_PCIE_1_PIPE_CLK_SRC>,
+				 <&pcie1_lane>,
+				 <&rpmhcc RPMH_CXO_CLK>,
+				 <&gcc GCC_PCIE_1_AUX_CLK>,
+				 <&gcc GCC_PCIE_1_CFG_AHB_CLK>,
+				 <&gcc GCC_PCIE_1_MSTR_AXI_CLK>,
+				 <&gcc GCC_PCIE_1_SLV_AXI_CLK>,
+				 <&gcc GCC_PCIE_1_SLV_Q2A_AXI_CLK>,
+				 <&gcc GCC_DDRSS_PCIE_SF_TBU_CLK>,
+				 <&gcc GCC_AGGRE_NOC_PCIE_1_AXI_CLK>;
+			clock-names = "pipe",
+				      "pipe_mux",
+				      "phy_pipe",
+				      "ref",
+				      "aux",
+				      "cfg",
+				      "bus_master",
+				      "bus_slave",
+				      "slave_q2a",
+				      "ddrss_sf_tbu",
+				      "aggre1";
+
+			iommus = <&apps_smmu 0x1c80 0x7f>;
+			iommu-map = <0x0   &apps_smmu 0x1c80 0x1>,
+				    <0x100 &apps_smmu 0x1c81 0x1>;
+
+			resets = <&gcc GCC_PCIE_1_BCR>;
+			reset-names = "pci";
+
+			power-domains = <&gcc PCIE_1_GDSC>;
+			power-domain-names = "gdsc";
+
+			phys = <&pcie1_lane>;
+			phy-names = "pciephy";
+
+			perst-gpio = <&tlmm 97 GPIO_ACTIVE_LOW>;
+			enable-gpio = <&tlmm 99 GPIO_ACTIVE_HIGH>;
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&pcie1_default_state>;
+
+			status = "disabled";
+		};
+
+		pcie1_phy: phy@1c0f000 {
+			compatible = "qcom,sm8450-qmp-gen4x2-pcie-phy";
+			reg = <0 0x01c0f000 0 0x200>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+			clocks = <&gcc GCC_PCIE_1_PHY_AUX_CLK>,
+				 <&gcc GCC_PCIE_1_CFG_AHB_CLK>,
+				 <&gcc GCC_PCIE_1_CLKREF_EN>,
+				 <&gcc GCC_PCIE_1_PHY_RCHNG_CLK>;
+			clock-names = "aux", "cfg_ahb", "ref", "refgen";
+
+			resets = <&gcc GCC_PCIE_1_PHY_BCR>;
+			reset-names = "phy";
+
+			assigned-clocks = <&gcc GCC_PCIE_1_PHY_RCHNG_CLK>;
+			assigned-clock-rates = <100000000>;
+
+			status = "disabled";
+
+			pcie1_lane: phy@1c0e000 {
+				reg = <0 0x1c0e000 0 0x200>, /* tx */
+				      <0 0x1c0e200 0 0x300>, /* rx */
+				      <0 0x1c0f200 0 0x200>, /* pcs */
+				      <0 0x1c0e800 0 0x200>, /* tx */
+				      <0 0x1c0ea00 0 0x300>, /* rx */
+				      <0 0x1c0f400 0 0xc00>; /* pcs_pcie */
+				clocks = <&gcc GCC_PCIE_1_PIPE_CLK>;
+				clock-names = "pipe0";
+
+				#clock-cells = <0>;
+				#phy-cells = <0>;
+				clock-output-names = "pcie_1_pipe_clk";
+			};
+		};
+
+		config_noc: interconnect@1500000 {
+			compatible = "qcom,sm8450-config-noc";
+			reg = <0 0x01500000 0 0x1c000>;
+			#interconnect-cells = <2>;
+			qcom,bcm-voters = <&apps_bcm_voter>;
+		};
+
+		system_noc: interconnect@1680000 {
+			compatible = "qcom,sm8450-system-noc";
+			reg = <0 0x01680000 0 0x1e200>;
+			#interconnect-cells = <2>;
+			qcom,bcm-voters = <&apps_bcm_voter>;
+		};
+
+		pcie_noc: interconnect@16c0000 {
+			compatible = "qcom,sm8450-pcie-anoc";
+			reg = <0 0x016c0000 0 0xe280>;
+			#interconnect-cells = <2>;
+			qcom,bcm-voters = <&apps_bcm_voter>;
+		};
+
+		aggre1_noc: interconnect@16e0000 {
+			compatible = "qcom,sm8450-aggre1-noc";
+			reg = <0 0x016e0000 0 0x1c080>;
+			#interconnect-cells = <2>;
+			clocks = <&gcc GCC_AGGRE_UFS_PHY_AXI_CLK>,
+				 <&gcc GCC_AGGRE_USB3_PRIM_AXI_CLK>;
+			qcom,bcm-voters = <&apps_bcm_voter>;
+		};
+
+		aggre2_noc: interconnect@1700000 {
+			compatible = "qcom,sm8450-aggre2-noc";
+			reg = <0 0x01700000 0 0x31080>;
+			#interconnect-cells = <2>;
+			qcom,bcm-voters = <&apps_bcm_voter>;
+			clocks = <&gcc GCC_AGGRE_NOC_PCIE_0_AXI_CLK>,
+				 <&gcc GCC_AGGRE_NOC_PCIE_1_AXI_CLK>,
+				 <&gcc GCC_AGGRE_UFS_PHY_AXI_CLK>,
+				 <&rpmhcc RPMH_IPA_CLK>;
+		};
+
+		mmss_noc: interconnect@1740000 {
+			compatible = "qcom,sm8450-mmss-noc";
+			reg = <0 0x01740000 0 0x1f080>;
+			#interconnect-cells = <2>;
+			qcom,bcm-voters = <&apps_bcm_voter>;
+		};
+
+		tcsr_mutex: hwlock@1f40000 {
+			compatible = "qcom,tcsr-mutex";
+			reg = <0x0 0x01f40000 0x0 0x40000>;
+			#hwlock-cells = <1>;
+		};
+
+		usb_1_hsphy: phy@88e3000 {
+			compatible = "qcom,sm8450-usb-hs-phy",
+				     "qcom,usb-snps-hs-7nm-phy";
+			reg = <0 0x088e3000 0 0x400>;
+			status = "disabled";
+			#phy-cells = <0>;
+
+			clocks = <&rpmhcc RPMH_CXO_CLK>;
+			clock-names = "ref";
+
+			resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>;
+		};
+
+		usb_1_qmpphy: phy-wrapper@88e9000 {
+			compatible = "qcom,sm8450-qmp-usb3-phy";
+			reg = <0 0x088e9000 0 0x200>,
+			      <0 0x088e8000 0 0x20>;
+			status = "disabled";
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+
+			clocks = <&gcc GCC_USB3_PRIM_PHY_AUX_CLK>,
+				 <&rpmhcc RPMH_CXO_CLK>,
+				 <&gcc GCC_USB3_PRIM_PHY_COM_AUX_CLK>;
+			clock-names = "aux", "ref_clk_src", "com_aux";
+
+			resets = <&gcc GCC_USB3_DP_PHY_PRIM_BCR>,
+				 <&gcc GCC_USB3_PHY_PRIM_BCR>;
+			reset-names = "phy", "common";
+
+			usb_1_ssphy: phy@88e9200 {
+				reg = <0 0x088e9200 0 0x200>,
+				      <0 0x088e9400 0 0x200>,
+				      <0 0x088e9c00 0 0x400>,
+				      <0 0x088e9600 0 0x200>,
+				      <0 0x088e9800 0 0x200>,
+				      <0 0x088e9a00 0 0x100>;
+				#phy-cells = <0>;
+				#clock-cells = <0>;
+				clocks = <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>;
+				clock-names = "pipe0";
+				clock-output-names = "usb3_phy_pipe_clk_src";
+			};
+		};
+
+		remoteproc_slpi: remoteproc@2400000 {
+			compatible = "qcom,sm8450-slpi-pas";
+			reg = <0 0x02400000 0 0x4000>;
+
+			interrupts-extended = <&pdc 9 IRQ_TYPE_EDGE_RISING>,
+					      <&smp2p_slpi_in 0 IRQ_TYPE_EDGE_RISING>,
+					      <&smp2p_slpi_in 1 IRQ_TYPE_EDGE_RISING>,
+					      <&smp2p_slpi_in 2 IRQ_TYPE_EDGE_RISING>,
+					      <&smp2p_slpi_in 3 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "wdog", "fatal", "ready",
+					  "handover", "stop-ack";
+
+			clocks = <&rpmhcc RPMH_CXO_CLK>;
+			clock-names = "xo";
+
+			power-domains = <&rpmhpd SM8450_LCX>,
+					<&rpmhpd SM8450_LMX>;
+			power-domain-names = "lcx", "lmx";
+
+			memory-region = <&slpi_mem>;
+
+			qcom,qmp = <&aoss_qmp>;
+
+			qcom,smem-states = <&smp2p_slpi_out 0>;
+			qcom,smem-state-names = "stop";
+
+			status = "disabled";
+
+			glink-edge {
+				interrupts-extended = <&ipcc IPCC_CLIENT_SLPI
+							     IPCC_MPROC_SIGNAL_GLINK_QMP
+							     IRQ_TYPE_EDGE_RISING>;
+				mboxes = <&ipcc IPCC_CLIENT_SLPI
+						IPCC_MPROC_SIGNAL_GLINK_QMP>;
+
+				label = "slpi";
+				qcom,remote-pid = <3>;
+
+				fastrpc {
+					compatible = "qcom,fastrpc";
+					qcom,glink-channels = "fastrpcglink-apps-dsp";
+					label = "sdsp";
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					compute-cb@1 {
+						compatible = "qcom,fastrpc-compute-cb";
+						reg = <1>;
+						iommus = <&apps_smmu 0x0541 0x0>;
+					};
+
+					compute-cb@2 {
+						compatible = "qcom,fastrpc-compute-cb";
+						reg = <2>;
+						iommus = <&apps_smmu 0x0542 0x0>;
+					};
+
+					compute-cb@3 {
+						compatible = "qcom,fastrpc-compute-cb";
+						reg = <3>;
+						iommus = <&apps_smmu 0x0543 0x0>;
+						/* note: shared-cb = <4> in downstream */
+					};
+				};
+			};
+		};
+
+		remoteproc_adsp: remoteproc@30000000 {
+			compatible = "qcom,sm8450-adsp-pas";
+			reg = <0 0x030000000 0 0x100>;
+
+			interrupts-extended = <&pdc 6 IRQ_TYPE_EDGE_RISING>,
+					      <&smp2p_adsp_in 0 IRQ_TYPE_EDGE_RISING>,
+					      <&smp2p_adsp_in 1 IRQ_TYPE_EDGE_RISING>,
+					      <&smp2p_adsp_in 2 IRQ_TYPE_EDGE_RISING>,
+					      <&smp2p_adsp_in 3 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "wdog", "fatal", "ready",
+					  "handover", "stop-ack";
+
+			clocks = <&rpmhcc RPMH_CXO_CLK>;
+			clock-names = "xo";
+
+			power-domains = <&rpmhpd SM8450_LCX>,
+					<&rpmhpd SM8450_LMX>;
+			power-domain-names = "lcx", "lmx";
+
+			memory-region = <&adsp_mem>;
+
+			qcom,qmp = <&aoss_qmp>;
+
+			qcom,smem-states = <&smp2p_adsp_out 0>;
+			qcom,smem-state-names = "stop";
+
+			status = "disabled";
+
+			remoteproc_adsp_glink: glink-edge {
+				interrupts-extended = <&ipcc IPCC_CLIENT_LPASS
+							     IPCC_MPROC_SIGNAL_GLINK_QMP
+							     IRQ_TYPE_EDGE_RISING>;
+				mboxes = <&ipcc IPCC_CLIENT_LPASS
+						IPCC_MPROC_SIGNAL_GLINK_QMP>;
+
+				label = "lpass";
+				qcom,remote-pid = <2>;
+
+				fastrpc {
+					compatible = "qcom,fastrpc";
+					qcom,glink-channels = "fastrpcglink-apps-dsp";
+					label = "adsp";
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					compute-cb@3 {
+						compatible = "qcom,fastrpc-compute-cb";
+						reg = <3>;
+						iommus = <&apps_smmu 0x1803 0x0>;
+					};
+
+					compute-cb@4 {
+						compatible = "qcom,fastrpc-compute-cb";
+						reg = <4>;
+						iommus = <&apps_smmu 0x1804 0x0>;
+					};
+
+					compute-cb@5 {
+						compatible = "qcom,fastrpc-compute-cb";
+						reg = <5>;
+						iommus = <&apps_smmu 0x1805 0x0>;
+					};
+				};
+			};
+		};
+
+		remoteproc_cdsp: remoteproc@32300000 {
+			compatible = "qcom,sm8450-cdsp-pas";
+			reg = <0 0x032300000 0 0x1400000>;
+
+			interrupts-extended = <&intc GIC_SPI 578 IRQ_TYPE_EDGE_RISING>,
+					      <&smp2p_cdsp_in 0 IRQ_TYPE_EDGE_RISING>,
+					      <&smp2p_cdsp_in 1 IRQ_TYPE_EDGE_RISING>,
+					      <&smp2p_cdsp_in 2 IRQ_TYPE_EDGE_RISING>,
+					      <&smp2p_cdsp_in 3 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "wdog", "fatal", "ready",
+					  "handover", "stop-ack";
+
+			clocks = <&rpmhcc RPMH_CXO_CLK>;
+			clock-names = "xo";
+
+			power-domains = <&rpmhpd SM8450_CX>,
+					<&rpmhpd SM8450_MXC>;
+			power-domain-names = "cx", "mxc";
+
+			memory-region = <&cdsp_mem>;
+
+			qcom,qmp = <&aoss_qmp>;
+
+			qcom,smem-states = <&smp2p_cdsp_out 0>;
+			qcom,smem-state-names = "stop";
+
+			status = "disabled";
+
+			glink-edge {
+				interrupts-extended = <&ipcc IPCC_CLIENT_CDSP
+							     IPCC_MPROC_SIGNAL_GLINK_QMP
+							     IRQ_TYPE_EDGE_RISING>;
+				mboxes = <&ipcc IPCC_CLIENT_CDSP
+						IPCC_MPROC_SIGNAL_GLINK_QMP>;
+
+				label = "cdsp";
+				qcom,remote-pid = <5>;
+
+				fastrpc {
+					compatible = "qcom,fastrpc";
+					qcom,glink-channels = "fastrpcglink-apps-dsp";
+					label = "cdsp";
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					compute-cb@1 {
+						compatible = "qcom,fastrpc-compute-cb";
+						reg = <1>;
+						iommus = <&apps_smmu 0x2161 0x0400>,
+							 <&apps_smmu 0x1021 0x1420>;
+					};
+
+					compute-cb@2 {
+						compatible = "qcom,fastrpc-compute-cb";
+						reg = <2>;
+						iommus = <&apps_smmu 0x2162 0x0400>,
+							 <&apps_smmu 0x1022 0x1420>;
+					};
+
+					compute-cb@3 {
+						compatible = "qcom,fastrpc-compute-cb";
+						reg = <3>;
+						iommus = <&apps_smmu 0x2163 0x0400>,
+							 <&apps_smmu 0x1023 0x1420>;
+					};
+
+					compute-cb@4 {
+						compatible = "qcom,fastrpc-compute-cb";
+						reg = <4>;
+						iommus = <&apps_smmu 0x2164 0x0400>,
+							 <&apps_smmu 0x1024 0x1420>;
+					};
+
+					compute-cb@5 {
+						compatible = "qcom,fastrpc-compute-cb";
+						reg = <5>;
+						iommus = <&apps_smmu 0x2165 0x0400>,
+							 <&apps_smmu 0x1025 0x1420>;
+					};
+
+					compute-cb@6 {
+						compatible = "qcom,fastrpc-compute-cb";
+						reg = <6>;
+						iommus = <&apps_smmu 0x2166 0x0400>,
+							 <&apps_smmu 0x1026 0x1420>;
+					};
+
+					compute-cb@7 {
+						compatible = "qcom,fastrpc-compute-cb";
+						reg = <7>;
+						iommus = <&apps_smmu 0x2167 0x0400>,
+							 <&apps_smmu 0x1027 0x1420>;
+					};
+
+					compute-cb@8 {
+						compatible = "qcom,fastrpc-compute-cb";
+						reg = <8>;
+						iommus = <&apps_smmu 0x2168 0x0400>,
+							 <&apps_smmu 0x1028 0x1420>;
+					};
+
+					/* note: secure cb9 in downstream */
+				};
+			};
+		};
+
+		remoteproc_mpss: remoteproc@4080000 {
+			compatible = "qcom,sm8450-mpss-pas";
+			reg = <0x0 0x04080000 0x0 0x4040>;
+
+			interrupts-extended = <&intc GIC_SPI 264 IRQ_TYPE_EDGE_RISING>,
+					      <&smp2p_modem_in 0 IRQ_TYPE_EDGE_RISING>,
+					      <&smp2p_modem_in 1 IRQ_TYPE_EDGE_RISING>,
+					      <&smp2p_modem_in 2 IRQ_TYPE_EDGE_RISING>,
+					      <&smp2p_modem_in 3 IRQ_TYPE_EDGE_RISING>,
+					      <&smp2p_modem_in 7 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "wdog", "fatal", "ready", "handover",
+					  "stop-ack", "shutdown-ack";
+
+			clocks = <&rpmhcc RPMH_CXO_CLK>;
+			clock-names = "xo";
+
+			power-domains = <&rpmhpd 0>,
+					<&rpmhpd 12>;
+			power-domain-names = "cx", "mss";
+
+			memory-region = <&mpss_mem>;
+
+			qcom,qmp = <&aoss_qmp>;
+
+			qcom,smem-states = <&smp2p_modem_out 0>;
+			qcom,smem-state-names = "stop";
+
+			status = "disabled";
+
+			glink-edge {
+				interrupts-extended = <&ipcc IPCC_CLIENT_MPSS
+							     IPCC_MPROC_SIGNAL_GLINK_QMP
+							     IRQ_TYPE_EDGE_RISING>;
+				mboxes = <&ipcc IPCC_CLIENT_MPSS
+						IPCC_MPROC_SIGNAL_GLINK_QMP>;
+				label = "modem";
+				qcom,remote-pid = <1>;
+			};
+		};
+
+		camcc: clock-controller@ade0000 {
+			compatible = "qcom,sm8450-camcc";
+			reg = <0 0x0ade0000 0 0x20000>;
+			clocks = <&gcc GCC_CAMERA_AHB_CLK>,
+				 <&rpmhcc RPMH_CXO_CLK>,
+				 <&rpmhcc RPMH_CXO_CLK_A>,
+				 <&sleep_clk>;
+			power-domains = <&rpmhpd SM8450_MMCX>;
+			required-opps = <&rpmhpd_opp_low_svs>;
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+			#power-domain-cells = <1>;
+			status = "disabled";
+		};
+
+		pdc: interrupt-controller@b220000 {
+			compatible = "qcom,sm8450-pdc", "qcom,pdc";
+			reg = <0 0x0b220000 0 0x30000>, <0 0x174000f0 0 0x64>;
+			qcom,pdc-ranges = <0 480 12>, <14 494 24>, <40 520 54>,
+					  <94 609 31>, <125 63 1>, <126 716 12>;
+			#interrupt-cells = <2>;
+			interrupt-parent = <&intc>;
+			interrupt-controller;
+		};
+
+		tsens0: thermal-sensor@c263000 {
+			compatible = "qcom,sm8450-tsens", "qcom,tsens-v2";
+			reg = <0 0x0c263000 0 0x1000>, /* TM */
+			      <0 0x0c222000 0 0x1000>; /* SROT */
+			#qcom,sensors = <16>;
+			interrupts = <GIC_SPI 506 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 508 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "uplow", "critical";
+			#thermal-sensor-cells = <1>;
+		};
+
+		tsens1: thermal-sensor@c265000 {
+			compatible = "qcom,sm8450-tsens", "qcom,tsens-v2";
+			reg = <0 0x0c265000 0 0x1000>, /* TM */
+			      <0 0x0c223000 0 0x1000>; /* SROT */
+			#qcom,sensors = <16>;
+			interrupts = <GIC_SPI 507 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 509 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "uplow", "critical";
+			#thermal-sensor-cells = <1>;
+		};
+
+		aoss_qmp: power-controller@c300000 {
+			compatible = "qcom,sm8450-aoss-qmp", "qcom,aoss-qmp";
+			reg = <0 0x0c300000 0 0x400>;
+			interrupts-extended = <&ipcc IPCC_CLIENT_AOP IPCC_MPROC_SIGNAL_GLINK_QMP
+						     IRQ_TYPE_EDGE_RISING>;
+			mboxes = <&ipcc IPCC_CLIENT_AOP IPCC_MPROC_SIGNAL_GLINK_QMP>;
+
+			#clock-cells = <0>;
+		};
+
+		ipcc: mailbox@ed18000 {
+			compatible = "qcom,sm8450-ipcc", "qcom,ipcc";
+			reg = <0 0x0ed18000 0 0x1000>;
+			interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-controller;
+			#interrupt-cells = <3>;
+			#mbox-cells = <2>;
+		};
+
+		tlmm: pinctrl@f100000 {
+			compatible = "qcom,sm8450-tlmm";
+			reg = <0 0x0f100000 0 0x300000>;
+			interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			gpio-ranges = <&tlmm 0 0 211>;
+			wakeup-parent = <&pdc>;
+
+			sdc2_sleep_state: sdc2-sleep-state {
+				clk-pins {
+					pins = "sdc2_clk";
+					drive-strength = <2>;
+					bias-disable;
+				};
+
+				cmd-pins {
+					pins = "sdc2_cmd";
+					drive-strength = <2>;
+					bias-pull-up;
+				};
+
+				data-pins {
+					pins = "sdc2_data";
+					drive-strength = <2>;
+					bias-pull-up;
+				};
+			};
+
+			pcie0_default_state: pcie0-default-state {
+				perst-pins {
+					pins = "gpio94";
+					function = "gpio";
+					drive-strength = <2>;
+					bias-pull-down;
+				};
+
+				clkreq-pins {
+					pins = "gpio95";
+					function = "pcie0_clkreqn";
+					drive-strength = <2>;
+					bias-pull-up;
+				};
+
+				wake-pins {
+					pins = "gpio96";
+					function = "gpio";
+					drive-strength = <2>;
+					bias-pull-up;
+				};
+			};
+
+			pcie1_default_state: pcie1-default-state {
+				perst-pins {
+					pins = "gpio97";
+					function = "gpio";
+					drive-strength = <2>;
+					bias-pull-down;
+				};
+
+				clkreq-pins {
+					pins = "gpio98";
+					function = "pcie1_clkreqn";
+					drive-strength = <2>;
+					bias-pull-up;
+				};
+
+				wake-pins {
+					pins = "gpio99";
+					function = "gpio";
+					drive-strength = <2>;
+					bias-pull-up;
+				};
+			};
+
+			qup_i2c0_data_clk: qup-i2c0-data-clk-state {
+				pins = "gpio0", "gpio1";
+				function = "qup0";
+			};
+
+			qup_i2c1_data_clk: qup-i2c1-data-clk-state {
+				pins = "gpio4", "gpio5";
+				function = "qup1";
+			};
+
+			qup_i2c2_data_clk: qup-i2c2-data-clk-state {
+				pins = "gpio8", "gpio9";
+				function = "qup2";
+			};
+
+			qup_i2c3_data_clk: qup-i2c3-data-clk-state {
+				pins = "gpio12", "gpio13";
+				function = "qup3";
+			};
+
+			qup_i2c4_data_clk: qup-i2c4-data-clk-state {
+				pins = "gpio16", "gpio17";
+				function = "qup4";
+			};
+
+			qup_i2c5_data_clk: qup-i2c5-data-clk-state {
+				pins = "gpio206", "gpio207";
+				function = "qup5";
+			};
+
+			qup_i2c6_data_clk: qup-i2c6-data-clk-state {
+				pins = "gpio20", "gpio21";
+				function = "qup6";
+			};
+
+			qup_i2c8_data_clk: qup-i2c8-data-clk-state {
+				pins = "gpio28", "gpio29";
+				function = "qup8";
+			};
+
+			qup_i2c9_data_clk: qup-i2c9-data-clk-state {
+				pins = "gpio32", "gpio33";
+				function = "qup9";
+			};
+
+			qup_i2c10_data_clk: qup-i2c10-data-clk-state {
+				pins = "gpio36", "gpio37";
+				function = "qup10";
+			};
+
+			qup_i2c11_data_clk: qup-i2c11-data-clk-state {
+				pins = "gpio40", "gpio41";
+				function = "qup11";
+			};
+
+			qup_i2c12_data_clk: qup-i2c12-data-clk-state {
+				pins = "gpio44", "gpio45";
+				function = "qup12";
+			};
+
+			qup_i2c13_data_clk: qup-i2c13-data-clk-state {
+				pins = "gpio48", "gpio49";
+				function = "qup13";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			qup_i2c14_data_clk: qup-i2c14-data-clk-state {
+				pins = "gpio52", "gpio53";
+				function = "qup14";
+				drive-strength = <2>;
+				bias-pull-up;
+			};
+
+			qup_i2c15_data_clk: qup-i2c15-data-clk-state {
+				pins = "gpio56", "gpio57";
+				function = "qup15";
+			};
+
+			qup_i2c16_data_clk: qup-i2c16-data-clk-state {
+				pins = "gpio60", "gpio61";
+				function = "qup16";
+			};
+
+			qup_i2c17_data_clk: qup-i2c17-data-clk-state {
+				pins = "gpio64", "gpio65";
+				function = "qup17";
+			};
+
+			qup_i2c18_data_clk: qup-i2c18-data-clk-state {
+				pins = "gpio68", "gpio69";
+				function = "qup18";
+			};
+
+			qup_i2c19_data_clk: qup-i2c19-data-clk-state {
+				pins = "gpio72", "gpio73";
+				function = "qup19";
+			};
+
+			qup_i2c20_data_clk: qup-i2c20-data-clk-state {
+				pins = "gpio76", "gpio77";
+				function = "qup20";
+			};
+
+			qup_i2c21_data_clk: qup-i2c21-data-clk-state {
+				pins = "gpio80", "gpio81";
+				function = "qup21";
+			};
+
+			qup_spi0_cs: qup-spi0-cs-state {
+				pins = "gpio3";
+				function = "qup0";
+			};
+
+			qup_spi0_data_clk: qup-spi0-data-clk-state {
+				pins = "gpio0", "gpio1", "gpio2";
+				function = "qup0";
+			};
+
+			qup_spi1_cs: qup-spi1-cs-state {
+				pins = "gpio7";
+				function = "qup1";
+			};
+
+			qup_spi1_data_clk: qup-spi1-data-clk-state {
+				pins = "gpio4", "gpio5", "gpio6";
+				function = "qup1";
+			};
+
+			qup_spi2_cs: qup-spi2-cs-state {
+				pins = "gpio11";
+				function = "qup2";
+			};
+
+			qup_spi2_data_clk: qup-spi2-data-clk-state {
+				pins = "gpio8", "gpio9", "gpio10";
+				function = "qup2";
+			};
+
+			qup_spi3_cs: qup-spi3-cs-state {
+				pins = "gpio15";
+				function = "qup3";
+			};
+
+			qup_spi3_data_clk: qup-spi3-data-clk-state {
+				pins = "gpio12", "gpio13", "gpio14";
+				function = "qup3";
+			};
+
+			qup_spi4_cs: qup-spi4-cs-state {
+				pins = "gpio19";
+				function = "qup4";
+				drive-strength = <6>;
+				bias-disable;
+			};
+
+			qup_spi4_data_clk: qup-spi4-data-clk-state {
+				pins = "gpio16", "gpio17", "gpio18";
+				function = "qup4";
+			};
+
+			qup_spi5_cs: qup-spi5-cs-state {
+				pins = "gpio85";
+				function = "qup5";
+			};
+
+			qup_spi5_data_clk: qup-spi5-data-clk-state {
+				pins = "gpio206", "gpio207", "gpio84";
+				function = "qup5";
+			};
+
+			qup_spi6_cs: qup-spi6-cs-state {
+				pins = "gpio23";
+				function = "qup6";
+			};
+
+			qup_spi6_data_clk: qup-spi6-data-clk-state {
+				pins = "gpio20", "gpio21", "gpio22";
+				function = "qup6";
+			};
+
+			qup_spi8_cs: qup-spi8-cs-state {
+				pins = "gpio31";
+				function = "qup8";
+			};
+
+			qup_spi8_data_clk: qup-spi8-data-clk-state {
+				pins = "gpio28", "gpio29", "gpio30";
+				function = "qup8";
+			};
+
+			qup_spi9_cs: qup-spi9-cs-state {
+				pins = "gpio35";
+				function = "qup9";
+			};
+
+			qup_spi9_data_clk: qup-spi9-data-clk-state {
+				pins = "gpio32", "gpio33", "gpio34";
+				function = "qup9";
+			};
+
+			qup_spi10_cs: qup-spi10-cs-state {
+				pins = "gpio39";
+				function = "qup10";
+			};
+
+			qup_spi10_data_clk: qup-spi10-data-clk-state {
+				pins = "gpio36", "gpio37", "gpio38";
+				function = "qup10";
+			};
+
+			qup_spi11_cs: qup-spi11-cs-state {
+				pins = "gpio43";
+				function = "qup11";
+			};
+
+			qup_spi11_data_clk: qup-spi11-data-clk-state {
+				pins = "gpio40", "gpio41", "gpio42";
+				function = "qup11";
+			};
+
+			qup_spi12_cs: qup-spi12-cs-state {
+				pins = "gpio47";
+				function = "qup12";
+			};
+
+			qup_spi12_data_clk: qup-spi12-data-clk-state {
+				pins = "gpio44", "gpio45", "gpio46";
+				function = "qup12";
+			};
+
+			qup_spi13_cs: qup-spi13-cs-state {
+				pins = "gpio51";
+				function = "qup13";
+			};
+
+			qup_spi13_data_clk: qup-spi13-data-clk-state {
+				pins = "gpio48", "gpio49", "gpio50";
+				function = "qup13";
+			};
+
+			qup_spi14_cs: qup-spi14-cs-state {
+				pins = "gpio55";
+				function = "qup14";
+			};
+
+			qup_spi14_data_clk: qup-spi14-data-clk-state {
+				pins = "gpio52", "gpio53", "gpio54";
+				function = "qup14";
+			};
+
+			qup_spi15_cs: qup-spi15-cs-state {
+				pins = "gpio59";
+				function = "qup15";
+			};
+
+			qup_spi15_data_clk: qup-spi15-data-clk-state {
+				pins = "gpio56", "gpio57", "gpio58";
+				function = "qup15";
+			};
+
+			qup_spi16_cs: qup-spi16-cs-state {
+				pins = "gpio63";
+				function = "qup16";
+			};
+
+			qup_spi16_data_clk: qup-spi16-data-clk-state {
+				pins = "gpio60", "gpio61", "gpio62";
+				function = "qup16";
+			};
+
+			qup_spi17_cs: qup-spi17-cs-state {
+				pins = "gpio67";
+				function = "qup17";
+			};
+
+			qup_spi17_data_clk: qup-spi17-data-clk-state {
+				pins = "gpio64", "gpio65", "gpio66";
+				function = "qup17";
+			};
+
+			qup_spi18_cs: qup-spi18-cs-state {
+				pins = "gpio71";
+				function = "qup18";
+				drive-strength = <6>;
+				bias-disable;
+			};
+
+			qup_spi18_data_clk: qup-spi18-data-clk-state {
+				pins = "gpio68", "gpio69", "gpio70";
+				function = "qup18";
+				drive-strength = <6>;
+				bias-disable;
+			};
+
+			qup_spi19_cs: qup-spi19-cs-state {
+				pins = "gpio75";
+				function = "qup19";
+				drive-strength = <6>;
+				bias-disable;
+			};
+
+			qup_spi19_data_clk: qup-spi19-data-clk-state {
+				pins = "gpio72", "gpio73", "gpio74";
+				function = "qup19";
+				drive-strength = <6>;
+				bias-disable;
+			};
+
+			qup_spi20_cs: qup-spi20-cs-state {
+				pins = "gpio79";
+				function = "qup20";
+			};
+
+			qup_spi20_data_clk: qup-spi20-data-clk-state {
+				pins = "gpio76", "gpio77", "gpio78";
+				function = "qup20";
+			};
+
+			qup_spi21_cs: qup-spi21-cs-state {
+				pins = "gpio83";
+				function = "qup21";
+			};
+
+			qup_spi21_data_clk: qup-spi21-data-clk-state {
+				pins = "gpio80", "gpio81", "gpio82";
+				function = "qup21";
+			};
+
+			qup_uart7_rx: qup-uart7-rx-state {
+				pins = "gpio26";
+				function = "qup7";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			qup_uart7_tx: qup-uart7-tx-state {
+				pins = "gpio27";
+				function = "qup7";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
+			qup_uart20_default: qup-uart20-default-state {
+				pins = "gpio76", "gpio77", "gpio78", "gpio79";
+				function = "qup20";
+			};
+
+		};
+
+		apps_smmu: iommu@15000000 {
+			compatible = "qcom,sm8450-smmu-500", "arm,mmu-500";
+			reg = <0 0x15000000 0 0x100000>;
+			#iommu-cells = <2>;
+			#global-interrupts = <1>;
+			interrupts =    <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 181 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 182 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 185 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 187 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 189 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 191 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 315 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 316 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 317 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 318 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 319 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 320 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 321 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 322 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 323 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 324 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 325 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 326 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 327 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 328 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 329 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 333 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 334 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 335 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 336 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 337 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 338 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 339 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 340 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 341 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 342 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 343 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 344 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 345 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 395 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 396 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 397 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 398 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 399 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 400 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 401 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 402 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 403 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 404 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 405 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 406 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 407 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 408 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 409 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 418 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 419 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 412 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 421 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 707 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 423 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 424 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 425 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 690 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 691 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 692 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 693 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 694 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 695 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 696 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 697 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		intc: interrupt-controller@17100000 {
+			compatible = "arm,gic-v3";
+			#interrupt-cells = <3>;
+			interrupt-controller;
+			#redistributor-regions = <1>;
+			redistributor-stride = <0x0 0x40000>;
+			reg = <0x0 0x17100000 0x0 0x10000>,     /* GICD */
+			      <0x0 0x17180000 0x0 0x200000>;    /* GICR * 8 */
+			interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+
+			gic_its: msi-controller@17140000 {
+				compatible = "arm,gic-v3-its";
+				reg = <0x0 0x17140000 0x0 0x20000>;
+				msi-controller;
+				#msi-cells = <1>;
+			};
+		};
+
+		timer@17420000 {
+			compatible = "arm,armv7-timer-mem";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0 0 0x20000000>;
+			reg = <0x0 0x17420000 0x0 0x1000>;
+			clock-frequency = <19200000>;
+
+			frame@17421000 {
+				frame-number = <0>;
+				interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x17421000 0x1000>,
+				      <0x17422000 0x1000>;
+			};
+
+			frame@17423000 {
+				frame-number = <1>;
+				interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x17423000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@17425000 {
+				frame-number = <2>;
+				interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x17425000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@17427000 {
+				frame-number = <3>;
+				interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x17427000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@17429000 {
+				frame-number = <4>;
+				interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x17429000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@1742b000 {
+				frame-number = <5>;
+				interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x1742b000 0x1000>;
+				status = "disabled";
+			};
+
+			frame@1742d000 {
+				frame-number = <6>;
+				interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x1742d000 0x1000>;
+				status = "disabled";
+			};
+		};
+
+		apps_rsc: rsc@17a00000 {
+			label = "apps_rsc";
+			compatible = "qcom,rpmh-rsc";
+			reg = <0x0 0x17a00000 0x0 0x10000>,
+			      <0x0 0x17a10000 0x0 0x10000>,
+			      <0x0 0x17a20000 0x0 0x10000>,
+			      <0x0 0x17a30000 0x0 0x10000>;
+			reg-names = "drv-0", "drv-1", "drv-2", "drv-3";
+			interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
+			qcom,tcs-offset = <0xd00>;
+			qcom,drv-id = <2>;
+			qcom,tcs-config = <ACTIVE_TCS  3>, <SLEEP_TCS   2>,
+					  <WAKE_TCS    2>, <CONTROL_TCS 0>;
+
+			apps_bcm_voter: bcm-voter {
+				compatible = "qcom,bcm-voter";
+			};
+
+			rpmhcc: clock-controller {
+				compatible = "qcom,sm8450-rpmh-clk";
+				#clock-cells = <1>;
+				clock-names = "xo";
+				clocks = <&xo_board>;
+			};
+
+			rpmhpd: power-controller {
+				compatible = "qcom,sm8450-rpmhpd";
+				#power-domain-cells = <1>;
+				operating-points-v2 = <&rpmhpd_opp_table>;
+
+				rpmhpd_opp_table: opp-table {
+					compatible = "operating-points-v2";
+
+					rpmhpd_opp_ret: opp1 {
+						opp-level = <RPMH_REGULATOR_LEVEL_RETENTION>;
+					};
+
+					rpmhpd_opp_min_svs: opp2 {
+						opp-level = <RPMH_REGULATOR_LEVEL_MIN_SVS>;
+					};
+
+					rpmhpd_opp_low_svs: opp3 {
+						opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>;
+					};
+
+					rpmhpd_opp_svs: opp4 {
+						opp-level = <RPMH_REGULATOR_LEVEL_SVS>;
+					};
+
+					rpmhpd_opp_svs_l1: opp5 {
+						opp-level = <RPMH_REGULATOR_LEVEL_SVS_L1>;
+					};
+
+					rpmhpd_opp_nom: opp6 {
+						opp-level = <RPMH_REGULATOR_LEVEL_NOM>;
+					};
+
+					rpmhpd_opp_nom_l1: opp7 {
+						opp-level = <RPMH_REGULATOR_LEVEL_NOM_L1>;
+					};
+
+					rpmhpd_opp_nom_l2: opp8 {
+						opp-level = <RPMH_REGULATOR_LEVEL_NOM_L2>;
+					};
+
+					rpmhpd_opp_turbo: opp9 {
+						opp-level = <RPMH_REGULATOR_LEVEL_TURBO>;
+					};
+
+					rpmhpd_opp_turbo_l1: opp10 {
+						opp-level = <RPMH_REGULATOR_LEVEL_TURBO_L1>;
+					};
+				};
+			};
+		};
+
+		cpufreq_hw: cpufreq@17d91000 {
+			compatible = "qcom,sm8450-cpufreq-epss", "qcom,cpufreq-epss";
+			reg = <0 0x17d91000 0 0x1000>,
+			      <0 0x17d92000 0 0x1000>,
+			      <0 0x17d93000 0 0x1000>;
+			reg-names = "freq-domain0", "freq-domain1", "freq-domain2";
+			clocks = <&rpmhcc RPMH_CXO_CLK>, <&gcc GCC_GPLL0>;
+			clock-names = "xo", "alternate";
+			interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "dcvsh-irq-0", "dcvsh-irq-1", "dcvsh-irq-2";
+			#freq-domain-cells = <1>;
+		};
+
+		gem_noc: interconnect@19100000 {
+			compatible = "qcom,sm8450-gem-noc";
+			reg = <0 0x19100000 0 0xbb800>;
+			#interconnect-cells = <2>;
+			qcom,bcm-voters = <&apps_bcm_voter>;
+		};
+
+		system-cache-controller@19200000 {
+			compatible = "qcom,sm8450-llcc";
+			reg = <0 0x19200000 0 0x580000>, <0 0x19a00000 0 0x80000>;
+			reg-names = "llcc_base", "llcc_broadcast_base";
+			interrupts = <GIC_SPI 266 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		ufs_mem_hc: ufshc@1d84000 {
+			compatible = "qcom,sm8450-ufshc", "qcom,ufshc",
+				     "jedec,ufs-2.0";
+			reg = <0 0x01d84000 0 0x3000>,
+			      <0 0x01d88000 0 0x8000>;
+			reg-names = "std", "ice";
+			interrupts = <GIC_SPI 265 IRQ_TYPE_LEVEL_HIGH>;
+			phys = <&ufs_mem_phy_lanes>;
+			phy-names = "ufsphy";
+			lanes-per-direction = <2>;
+			#reset-cells = <1>;
+			resets = <&gcc GCC_UFS_PHY_BCR>;
+			reset-names = "rst";
+
+			power-domains = <&gcc UFS_PHY_GDSC>;
+
+			iommus = <&apps_smmu 0xe0 0x0>;
+
+			interconnects = <&aggre1_noc MASTER_UFS_MEM 0 &mc_virt SLAVE_EBI1 0>,
+					<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_UFS_MEM_CFG 0>;
+			interconnect-names = "ufs-ddr", "cpu-ufs";
+			clock-names =
+				"core_clk",
+				"bus_aggr_clk",
+				"iface_clk",
+				"core_clk_unipro",
+				"ref_clk",
+				"tx_lane0_sync_clk",
+				"rx_lane0_sync_clk",
+				"rx_lane1_sync_clk",
+				"ice_core_clk";
+			clocks =
+				<&gcc GCC_UFS_PHY_AXI_CLK>,
+				<&gcc GCC_AGGRE_UFS_PHY_AXI_CLK>,
+				<&gcc GCC_UFS_PHY_AHB_CLK>,
+				<&gcc GCC_UFS_PHY_UNIPRO_CORE_CLK>,
+				<&rpmhcc RPMH_CXO_CLK>,
+				<&gcc GCC_UFS_PHY_TX_SYMBOL_0_CLK>,
+				<&gcc GCC_UFS_PHY_RX_SYMBOL_0_CLK>,
+				<&gcc GCC_UFS_PHY_RX_SYMBOL_1_CLK>,
+				<&gcc GCC_UFS_PHY_ICE_CORE_CLK>;
+			freq-table-hz =
+				<75000000 300000000>,
+				<0 0>,
+				<0 0>,
+				<75000000 300000000>,
+				<75000000 300000000>,
+				<0 0>,
+				<0 0>,
+				<0 0>,
+				<75000000 300000000>;
+			status = "disabled";
+		};
+
+		ufs_mem_phy: phy@1d87000 {
+			compatible = "qcom,sm8450-qmp-ufs-phy";
+			reg = <0 0x01d87000 0 0x1c4>;
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+			clock-names = "ref", "ref_aux", "qref";
+			clocks = <&rpmhcc RPMH_CXO_CLK>,
+				 <&gcc GCC_UFS_PHY_PHY_AUX_CLK>,
+				 <&gcc GCC_UFS_0_CLKREF_EN>;
+
+			resets = <&ufs_mem_hc 0>;
+			reset-names = "ufsphy";
+			status = "disabled";
+
+			ufs_mem_phy_lanes: phy@1d87400 {
+				reg = <0 0x01d87400 0 0x108>,
+				      <0 0x01d87600 0 0x1e0>,
+				      <0 0x01d87c00 0 0x1dc>,
+				      <0 0x01d87800 0 0x108>,
+				      <0 0x01d87a00 0 0x1e0>;
+				#phy-cells = <0>;
+			};
+		};
+
+		sdhc_2: sdhci@8804000 {
+			compatible = "qcom,sm8450-sdhci", "qcom,sdhci-msm-v5";
+			reg = <0 0x08804000 0 0x1000>;
+
+			interrupts = <GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 223 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "hc_irq", "pwr_irq";
+
+			clocks = <&gcc GCC_SDCC2_AHB_CLK>,
+				 <&gcc GCC_SDCC2_APPS_CLK>,
+				 <&rpmhcc RPMH_CXO_CLK>;
+			clock-names = "iface", "core", "xo";
+			resets = <&gcc GCC_SDCC2_BCR>;
+			interconnects = <&aggre2_noc MASTER_SDCC_2 0 &mc_virt SLAVE_EBI1 0>,
+					<&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_SDCC_2 0>;
+			interconnect-names = "sdhc-ddr","cpu-sdhc";
+			iommus = <&apps_smmu 0x4a0 0x0>;
+			power-domains = <&rpmhpd SM8450_CX>;
+			operating-points-v2 = <&sdhc2_opp_table>;
+			bus-width = <4>;
+			dma-coherent;
+
+			status = "disabled";
+
+			sdhc2_opp_table: opp-table {
+				compatible = "operating-points-v2";
+
+				opp-100000000 {
+					opp-hz = /bits/ 64 <100000000>;
+					required-opps = <&rpmhpd_opp_low_svs>;
+				};
+
+				opp-202000000 {
+					opp-hz = /bits/ 64 <202000000>;
+					required-opps = <&rpmhpd_opp_svs_l1>;
+				};
+			};
+		};
+
+		usb_1: usb@a6f8800 {
+			compatible = "qcom,sm8450-dwc3", "qcom,dwc3";
+			reg = <0 0x0a6f8800 0 0x400>;
+			status = "disabled";
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges;
+
+			clocks = <&gcc GCC_CFG_NOC_USB3_PRIM_AXI_CLK>,
+				 <&gcc GCC_USB30_PRIM_MASTER_CLK>,
+				 <&gcc GCC_AGGRE_USB3_PRIM_AXI_CLK>,
+				 <&gcc GCC_USB30_PRIM_SLEEP_CLK>,
+				 <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
+				 <&gcc GCC_USB3_0_CLKREF_EN>;
+			clock-names = "cfg_noc",
+				      "core",
+				      "iface",
+				      "sleep",
+				      "mock_utmi",
+				      "xo";
+
+			assigned-clocks = <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>,
+					  <&gcc GCC_USB30_PRIM_MASTER_CLK>;
+			assigned-clock-rates = <19200000>, <200000000>;
+
+			interrupts-extended = <&intc GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>,
+					      <&pdc 17 IRQ_TYPE_LEVEL_HIGH>,
+					      <&pdc 15 IRQ_TYPE_EDGE_BOTH>,
+					      <&pdc 14 IRQ_TYPE_EDGE_BOTH>;
+			interrupt-names = "hs_phy_irq",
+					  "ss_phy_irq",
+					  "dm_hs_phy_irq",
+					  "dp_hs_phy_irq";
+
+			power-domains = <&gcc USB30_PRIM_GDSC>;
+
+			resets = <&gcc GCC_USB30_PRIM_BCR>;
+
+			usb_1_dwc3: usb@a600000 {
+				compatible = "snps,dwc3";
+				reg = <0 0x0a600000 0 0xcd00>;
+				interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
+				iommus = <&apps_smmu 0x0 0x0>;
+				snps,dis_u2_susphy_quirk;
+				snps,dis_enblslpm_quirk;
+				phys = <&usb_1_hsphy>, <&usb_1_ssphy>;
+				phy-names = "usb2-phy", "usb3-phy";
+			};
+		};
+
+		nsp_noc: interconnect@320c0000 {
+			compatible = "qcom,sm8450-nsp-noc";
+			reg = <0 0x320c0000 0 0x10000>;
+			#interconnect-cells = <2>;
+			qcom,bcm-voters = <&apps_bcm_voter>;
+		};
+
+		lpass_ag_noc: interconnect@3c40000 {
+			compatible = "qcom,sm8450-lpass-ag-noc";
+			reg = <0 0x3c40000 0 0x17200>;
+			#interconnect-cells = <2>;
+			qcom,bcm-voters = <&apps_bcm_voter>;
+		};
+	};
+
+	thermal-zones {
+		aoss0-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens0 0>;
+
+			trips {
+				thermal-engine-config {
+					temperature = <125000>;
+					hysteresis = <1000>;
+					type = "passive";
+				};
+
+				reset-mon-cfg {
+					temperature = <115000>;
+					hysteresis = <5000>;
+					type = "passive";
+				};
+			};
+		};
+
+		cpuss0-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens0 1>;
+
+			trips {
+				thermal-engine-config {
+					temperature = <125000>;
+					hysteresis = <1000>;
+					type = "passive";
+				};
+
+				reset-mon-cfg {
+					temperature = <115000>;
+					hysteresis = <5000>;
+					type = "passive";
+				};
+			};
+		};
+
+		cpuss1-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens0 2>;
+
+			trips {
+				thermal-engine-config {
+					temperature = <125000>;
+					hysteresis = <1000>;
+					type = "passive";
+				};
+
+				reset-mon-cfg {
+					temperature = <115000>;
+					hysteresis = <5000>;
+					type = "passive";
+				};
+			};
+		};
+
+		cpuss3-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens0 3>;
+
+			trips {
+				thermal-engine-config {
+					temperature = <125000>;
+					hysteresis = <1000>;
+					type = "passive";
+				};
+
+				reset-mon-cfg {
+					temperature = <115000>;
+					hysteresis = <5000>;
+					type = "passive";
+				};
+			};
+		};
+
+		cpuss4-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens0 4>;
+
+			trips {
+				thermal-engine-config {
+					temperature = <125000>;
+					hysteresis = <1000>;
+					type = "passive";
+				};
+
+				reset-mon-cfg {
+					temperature = <115000>;
+					hysteresis = <5000>;
+					type = "passive";
+				};
+			};
+		};
+
+		cpu4-top-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens0 5>;
+
+			trips {
+				cpu4_top_alert0: trip-point0 {
+					temperature = <90000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				cpu4_top_alert1: trip-point1 {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				cpu4_top_crit: cpu_crit {
+					temperature = <110000>;
+					hysteresis = <1000>;
+					type = "critical";
+				};
+			};
+		};
+
+		cpu4-bottom-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens0 6>;
+
+			trips {
+				cpu4_bottom_alert0: trip-point0 {
+					temperature = <90000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				cpu4_bottom_alert1: trip-point1 {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				cpu4_bottom_crit: cpu_crit {
+					temperature = <110000>;
+					hysteresis = <1000>;
+					type = "critical";
+				};
+			};
+		};
+
+		cpu5-top-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens0 7>;
+
+			trips {
+				cpu5_top_alert0: trip-point0 {
+					temperature = <90000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				cpu5_top_alert1: trip-point1 {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				cpu5_top_crit: cpu_crit {
+					temperature = <110000>;
+					hysteresis = <1000>;
+					type = "critical";
+				};
+			};
+		};
+
+		cpu5-bottom-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens0 8>;
+
+			trips {
+				cpu5_bottom_alert0: trip-point0 {
+					temperature = <90000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				cpu5_bottom_alert1: trip-point1 {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				cpu5_bottom_crit: cpu_crit {
+					temperature = <110000>;
+					hysteresis = <1000>;
+					type = "critical";
+				};
+			};
+		};
+
+		cpu6-top-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens0 9>;
+
+			trips {
+				cpu6_top_alert0: trip-point0 {
+					temperature = <90000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				cpu6_top_alert1: trip-point1 {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				cpu6_top_crit: cpu_crit {
+					temperature = <110000>;
+					hysteresis = <1000>;
+					type = "critical";
+				};
+			};
+		};
+
+		cpu6-bottom-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens0 10>;
+
+			trips {
+				cpu6_bottom_alert0: trip-point0 {
+					temperature = <90000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				cpu6_bottom_alert1: trip-point1 {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				cpu6_bottom_crit: cpu_crit {
+					temperature = <110000>;
+					hysteresis = <1000>;
+					type = "critical";
+				};
+			};
+		};
+
+		cpu7-top-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens0 11>;
+
+			trips {
+				cpu7_top_alert0: trip-point0 {
+					temperature = <90000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				cpu7_top_alert1: trip-point1 {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				cpu7_top_crit: cpu_crit {
+					temperature = <110000>;
+					hysteresis = <1000>;
+					type = "critical";
+				};
+			};
+		};
+
+		cpu7-middle-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens0 12>;
+
+			trips {
+				cpu7_middle_alert0: trip-point0 {
+					temperature = <90000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				cpu7_middle_alert1: trip-point1 {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				cpu7_middle_crit: cpu_crit {
+					temperature = <110000>;
+					hysteresis = <1000>;
+					type = "critical";
+				};
+			};
+		};
+
+		cpu7-bottom-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens0 13>;
+
+			trips {
+				cpu7_bottom_alert0: trip-point0 {
+					temperature = <90000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				cpu7_bottom_alert1: trip-point1 {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				cpu7_bottom_crit: cpu_crit {
+					temperature = <110000>;
+					hysteresis = <1000>;
+					type = "critical";
+				};
+			};
+		};
+
+		gpu-top-thermal {
+			polling-delay-passive = <10>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens0 14>;
+
+			trips {
+				thermal-engine-config {
+					temperature = <125000>;
+					hysteresis = <1000>;
+					type = "passive";
+				};
+
+				thermal-hal-config {
+					temperature = <125000>;
+					hysteresis = <1000>;
+					type = "passive";
+				};
+
+				reset-mon-cfg {
+					temperature = <115000>;
+					hysteresis = <5000>;
+					type = "passive";
+				};
+
+				gpu0_tj_cfg: tj_cfg {
+					temperature = <95000>;
+					hysteresis = <5000>;
+					type = "passive";
+				};
+			};
+		};
+
+		gpu-bottom-thermal {
+			polling-delay-passive = <10>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens0 15>;
+
+			trips {
+				thermal-engine-config {
+					temperature = <125000>;
+					hysteresis = <1000>;
+					type = "passive";
+				};
+
+				thermal-hal-config {
+					temperature = <125000>;
+					hysteresis = <1000>;
+					type = "passive";
+				};
+
+				reset-mon-cfg {
+					temperature = <115000>;
+					hysteresis = <5000>;
+					type = "passive";
+				};
+
+				gpu1_tj_cfg: tj_cfg {
+					temperature = <95000>;
+					hysteresis = <5000>;
+					type = "passive";
+				};
+			};
+		};
+
+		aoss1-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens1 0>;
+
+			trips {
+				thermal-engine-config {
+					temperature = <125000>;
+					hysteresis = <1000>;
+					type = "passive";
+				};
+
+				reset-mon-cfg {
+					temperature = <115000>;
+					hysteresis = <5000>;
+					type = "passive";
+				};
+			};
+		};
+
+		cpu0-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens1 1>;
+
+			trips {
+				cpu0_alert0: trip-point0 {
+					temperature = <90000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				cpu0_alert1: trip-point1 {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				cpu0_crit: cpu_crit {
+					temperature = <110000>;
+					hysteresis = <1000>;
+					type = "critical";
+				};
+			};
+		};
+
+		cpu1-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens1 2>;
+
+			trips {
+				cpu1_alert0: trip-point0 {
+					temperature = <90000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				cpu1_alert1: trip-point1 {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				cpu1_crit: cpu_crit {
+					temperature = <110000>;
+					hysteresis = <1000>;
+					type = "critical";
+				};
+			};
+		};
+
+		cpu2-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens1 3>;
+
+			trips {
+				cpu2_alert0: trip-point0 {
+					temperature = <90000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				cpu2_alert1: trip-point1 {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				cpu2_crit: cpu_crit {
+					temperature = <110000>;
+					hysteresis = <1000>;
+					type = "critical";
+				};
+			};
+		};
+
+		cpu3-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens1 4>;
+
+			trips {
+				cpu3_alert0: trip-point0 {
+					temperature = <90000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				cpu3_alert1: trip-point1 {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				cpu3_crit: cpu_crit {
+					temperature = <110000>;
+					hysteresis = <1000>;
+					type = "critical";
+				};
+			};
+		};
+
+		cdsp0-thermal {
+			polling-delay-passive = <10>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens1 5>;
+
+			trips {
+				thermal-engine-config {
+					temperature = <125000>;
+					hysteresis = <1000>;
+					type = "passive";
+				};
+
+				thermal-hal-config {
+					temperature = <125000>;
+					hysteresis = <1000>;
+					type = "passive";
+				};
+
+				reset-mon-cfg {
+					temperature = <115000>;
+					hysteresis = <5000>;
+					type = "passive";
+				};
+
+				cdsp_0_config: junction-config {
+					temperature = <95000>;
+					hysteresis = <5000>;
+					type = "passive";
+				};
+			};
+		};
+
+		cdsp1-thermal {
+			polling-delay-passive = <10>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens1 6>;
+
+			trips {
+				thermal-engine-config {
+					temperature = <125000>;
+					hysteresis = <1000>;
+					type = "passive";
+				};
+
+				thermal-hal-config {
+					temperature = <125000>;
+					hysteresis = <1000>;
+					type = "passive";
+				};
+
+				reset-mon-cfg {
+					temperature = <115000>;
+					hysteresis = <5000>;
+					type = "passive";
+				};
+
+				cdsp_1_config: junction-config {
+					temperature = <95000>;
+					hysteresis = <5000>;
+					type = "passive";
+				};
+			};
+		};
+
+		cdsp2-thermal {
+			polling-delay-passive = <10>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens1 7>;
+
+			trips {
+				thermal-engine-config {
+					temperature = <125000>;
+					hysteresis = <1000>;
+					type = "passive";
+				};
+
+				thermal-hal-config {
+					temperature = <125000>;
+					hysteresis = <1000>;
+					type = "passive";
+				};
+
+				reset-mon-cfg {
+					temperature = <115000>;
+					hysteresis = <5000>;
+					type = "passive";
+				};
+
+				cdsp_2_config: junction-config {
+					temperature = <95000>;
+					hysteresis = <5000>;
+					type = "passive";
+				};
+			};
+		};
+
+		video-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens1 8>;
+
+			trips {
+				thermal-engine-config {
+					temperature = <125000>;
+					hysteresis = <1000>;
+					type = "passive";
+				};
+
+				reset-mon-cfg {
+					temperature = <115000>;
+					hysteresis = <5000>;
+					type = "passive";
+				};
+			};
+		};
+
+		mem-thermal {
+			polling-delay-passive = <10>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens1 9>;
+
+			trips {
+				thermal-engine-config {
+					temperature = <125000>;
+					hysteresis = <1000>;
+					type = "passive";
+				};
+
+				ddr_config0: ddr0-config {
+					temperature = <90000>;
+					hysteresis = <5000>;
+					type = "passive";
+				};
+
+				reset-mon-cfg {
+					temperature = <115000>;
+					hysteresis = <5000>;
+					type = "passive";
+				};
+			};
+		};
+
+		modem0-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens1 10>;
+
+			trips {
+				thermal-engine-config {
+					temperature = <125000>;
+					hysteresis = <1000>;
+					type = "passive";
+				};
+
+				mdmss0_config0: mdmss0-config0 {
+					temperature = <102000>;
+					hysteresis = <3000>;
+					type = "passive";
+				};
+
+				mdmss0_config1: mdmss0-config1 {
+					temperature = <105000>;
+					hysteresis = <3000>;
+					type = "passive";
+				};
+
+				reset-mon-cfg {
+					temperature = <115000>;
+					hysteresis = <5000>;
+					type = "passive";
+				};
+			};
+		};
+
+		modem1-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens1 11>;
+
+			trips {
+				thermal-engine-config {
+					temperature = <125000>;
+					hysteresis = <1000>;
+					type = "passive";
+				};
+
+				mdmss1_config0: mdmss1-config0 {
+					temperature = <102000>;
+					hysteresis = <3000>;
+					type = "passive";
+				};
+
+				mdmss1_config1: mdmss1-config1 {
+					temperature = <105000>;
+					hysteresis = <3000>;
+					type = "passive";
+				};
+
+				reset-mon-cfg {
+					temperature = <115000>;
+					hysteresis = <5000>;
+					type = "passive";
+				};
+			};
+		};
+
+		modem2-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens1 12>;
+
+			trips {
+				thermal-engine-config {
+					temperature = <125000>;
+					hysteresis = <1000>;
+					type = "passive";
+				};
+
+				mdmss2_config0: mdmss2-config0 {
+					temperature = <102000>;
+					hysteresis = <3000>;
+					type = "passive";
+				};
+
+				mdmss2_config1: mdmss2-config1 {
+					temperature = <105000>;
+					hysteresis = <3000>;
+					type = "passive";
+				};
+
+				reset-mon-cfg {
+					temperature = <115000>;
+					hysteresis = <5000>;
+					type = "passive";
+				};
+			};
+		};
+
+		modem3-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens1 13>;
+
+			trips {
+				thermal-engine-config {
+					temperature = <125000>;
+					hysteresis = <1000>;
+					type = "passive";
+				};
+
+				mdmss3_config0: mdmss3-config0 {
+					temperature = <102000>;
+					hysteresis = <3000>;
+					type = "passive";
+				};
+
+				mdmss3_config1: mdmss3-config1 {
+					temperature = <105000>;
+					hysteresis = <3000>;
+					type = "passive";
+				};
+
+				reset-mon-cfg {
+					temperature = <115000>;
+					hysteresis = <5000>;
+					type = "passive";
+				};
+			};
+		};
+
+		camera0-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens1 14>;
+
+			trips {
+				thermal-engine-config {
+					temperature = <125000>;
+					hysteresis = <1000>;
+					type = "passive";
+				};
+
+				reset-mon-cfg {
+					temperature = <115000>;
+					hysteresis = <5000>;
+					type = "passive";
+				};
+			};
+		};
+
+		camera1-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&tsens1 15>;
+
+			trips {
+				thermal-engine-config {
+					temperature = <125000>;
+					hysteresis = <1000>;
+					type = "passive";
+				};
+
+				reset-mon-cfg {
+					temperature = <115000>;
+					hysteresis = <5000>;
+					type = "passive";
+				};
+			};
+		};
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>;
+		clock-frequency = <19200000>;
+	};
+};
diff --git a/arch/arm64/boot/dts/renesas/Makefile b/arch/arm64/boot/dts/renesas/Makefile
index d1c5c21d8d14..0699b51c1247 100644
--- a/arch/arm64/boot/dts/renesas/Makefile
+++ b/arch/arm64/boot/dts/renesas/Makefile
@@ -56,6 +56,7 @@ dtb-$(CONFIG_ARCH_R8A77970) += r8a77970-v3msk.dtb
 
 dtb-$(CONFIG_ARCH_R8A77980) += r8a77980-condor.dtb
 dtb-$(CONFIG_ARCH_R8A77980) += r8a77980-v3hsk.dtb
+dtb-$(CONFIG_ARCH_R8A77980) += r8a77980a-condor-i.dtb
 
 dtb-$(CONFIG_ARCH_R8A77990) += r8a77990-ebisu.dtb
 
@@ -63,6 +64,10 @@ dtb-$(CONFIG_ARCH_R8A77995) += r8a77995-draak.dtb
 
 dtb-$(CONFIG_ARCH_R8A779A0) += r8a779a0-falcon.dtb
 
+dtb-$(CONFIG_ARCH_R8A779F0) += r8a779f0-spider.dtb
+
+dtb-$(CONFIG_ARCH_R8A779G0) += r8a779g0-white-hawk.dtb
+
 dtb-$(CONFIG_ARCH_R8A77951) += r8a779m1-salvator-xs.dtb
 dtb-$(CONFIG_ARCH_R8A77951) += r8a779m1-ulcb.dtb
 dtb-$(CONFIG_ARCH_R8A77951) += r8a779m1-ulcb-kf.dtb
@@ -73,4 +78,14 @@ dtb-$(CONFIG_ARCH_R8A77961) += r8a779m3-ulcb-kf.dtb
 
 dtb-$(CONFIG_ARCH_R8A77965) += r8a779m5-salvator-xs.dtb
 
+dtb-$(CONFIG_ARCH_R9A07G043) += r9a07g043u11-smarc.dtb
+
+dtb-$(CONFIG_ARCH_R9A07G044) += r9a07g044c2-smarc.dtb
 dtb-$(CONFIG_ARCH_R9A07G044) += r9a07g044l2-smarc.dtb
+
+dtb-$(CONFIG_ARCH_R9A07G054) += r9a07g054l2-smarc.dtb
+
+dtb-$(CONFIG_ARCH_R9A09G011) += r9a09g011-v2mevk2.dtb
+
+dtb-$(CONFIG_ARCH_RCAR_GEN3) += draak-ebisu-panel-aa104xd12.dtbo
+dtb-$(CONFIG_ARCH_RCAR_GEN3) += salvator-panel-aa104xd12.dtbo
diff --git a/arch/arm64/boot/dts/renesas/beacon-renesom-baseboard.dtsi b/arch/arm64/boot/dts/renesas/beacon-renesom-baseboard.dtsi
index 2692cc64bff6..8166e3c1ff4e 100644
--- a/arch/arm64/boot/dts/renesas/beacon-renesom-baseboard.dtsi
+++ b/arch/arm64/boot/dts/renesas/beacon-renesom-baseboard.dtsi
@@ -5,7 +5,7 @@
 
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>
-#include <dt-bindings/clk/versaclock.h>
+#include <dt-bindings/clock/versaclock.h>
 
 / {
 	backlight_lvds: backlight-lvds {
@@ -146,7 +146,7 @@
 		};
 	};
 
-	reg_audio: regulator_audio {
+	reg_audio: regulator-audio {
 		compatible = "regulator-fixed";
 		regulator-name = "audio-1.8V";
 		regulator-min-microvolt = <1800000>;
@@ -174,7 +174,7 @@
 		vin-supply = <&reg_lcd>;
 	};
 
-	reg_cam0: regulator_camera {
+	reg_cam0: regulator-cam0 {
 		compatible = "regulator-fixed";
 		regulator-name = "reg_cam0";
 		regulator-min-microvolt = <1800000>;
@@ -183,7 +183,7 @@
 		enable-active-high;
 	};
 
-	reg_cam1: regulator_camera {
+	reg_cam1: regulator-cam1 {
 		compatible = "regulator-fixed";
 		regulator-name = "reg_cam1";
 		regulator-min-microvolt = <1800000>;
@@ -272,8 +272,14 @@
 	status = "okay";
 };
 
-&du_out_rgb {
-	remote-endpoint = <&rgb_panel>;
+&du {
+	ports {
+		port@0 {
+			du_out_rgb: endpoint {
+				remote-endpoint = <&rgb_panel>;
+			};
+		};
+	};
 };
 
 &ehci0 {
@@ -359,11 +365,10 @@
 		clocks = <&x304_clk>;
 		clock-names = "xin";
 
-		assigned-clocks = <&versaclock6_bb 1>,
-				   <&versaclock6_bb 2>,
-				   <&versaclock6_bb 3>,
-				   <&versaclock6_bb 4>;
-		assigned-clock-rates =	<24000000>, <24000000>, <24000000>, <24576000>;
+		assigned-clocks = <&versaclock6_bb 1>, <&versaclock6_bb 2>,
+				  <&versaclock6_bb 3>, <&versaclock6_bb 4>;
+		assigned-clock-rates = <24000000>, <24000000>, <24000000>,
+				       <24576000>;
 
 		OUT1 {
 			idt,mode = <VC5_CMOS>;
diff --git a/arch/arm64/boot/dts/renesas/beacon-renesom-som.dtsi b/arch/arm64/boot/dts/renesas/beacon-renesom-som.dtsi
index 0d136809eb96..d3fc8ffd5b4c 100644
--- a/arch/arm64/boot/dts/renesas/beacon-renesom-som.dtsi
+++ b/arch/arm64/boot/dts/renesas/beacon-renesom-som.dtsi
@@ -4,7 +4,7 @@
  */
 
 #include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/clk/versaclock.h>
+#include <dt-bindings/clock/versaclock.h>
 
 / {
 	memory@48000000 {
@@ -20,7 +20,7 @@
 		clock-output-names = "osc_32k";
 	};
 
-	reg_1p8v: regulator0 {
+	reg_1p8v: regulator-1p8v {
 		compatible = "regulator-fixed";
 		regulator-name = "fixed-1.8V";
 		regulator-min-microvolt = <1800000>;
@@ -29,7 +29,7 @@
 		regulator-always-on;
 	};
 
-	reg_3p3v: regulator1 {
+	reg_3p3v: regulator-3p3v {
 		compatible = "regulator-fixed";
 		regulator-name = "fixed-3.3V";
 		regulator-min-microvolt = <3300000>;
@@ -77,7 +77,7 @@
 };
 
 &gpio6 {
-	usb_hub_reset {
+	usb-hub-reset-hog {
 		gpio-hog;
 		gpios = <10 GPIO_ACTIVE_HIGH>;
 		output-high;
@@ -293,7 +293,6 @@
 	vqmmc-supply = <&reg_1p8v>;
 	non-removable;
 	cap-power-off-card;
-	pm-ignore-notify;
 	keep-power-in-suspend;
 	mmc-pwrseq = <&wlan_pwrseq>;
 	status = "okay";
diff --git a/arch/arm64/boot/dts/renesas/cat875.dtsi b/arch/arm64/boot/dts/renesas/cat875.dtsi
index a69d24e9c61d..8c9da8b4bd60 100644
--- a/arch/arm64/boot/dts/renesas/cat875.dtsi
+++ b/arch/arm64/boot/dts/renesas/cat875.dtsi
@@ -18,6 +18,7 @@
 	pinctrl-names = "default";
 	renesas,no-ether-link;
 	phy-handle = <&phy0>;
+	phy-mode = "rgmii-id";
 	status = "okay";
 
 	phy0: ethernet-phy@0 {
diff --git a/arch/arm64/boot/dts/renesas/condor-common.dtsi b/arch/arm64/boot/dts/renesas/condor-common.dtsi
new file mode 100644
index 000000000000..dfbe35bf46e0
--- /dev/null
+++ b/arch/arm64/boot/dts/renesas/condor-common.dtsi
@@ -0,0 +1,548 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device Tree Source for the Condor board with R-Car V3H
+ *
+ * Copyright (C) 2018 Renesas Electronics Corp.
+ * Copyright (C) 2018 Cogent Embedded, Inc.
+ */
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	aliases {
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+		i2c2 = &i2c2;
+		i2c3 = &i2c3;
+		i2c4 = &i2c4;
+		i2c5 = &i2c5;
+		serial0 = &scif0;
+		ethernet0 = &gether;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	d1_8v: regulator-2 {
+		compatible = "regulator-fixed";
+		regulator-name = "D1.8V";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	d3_3v: regulator-0 {
+		compatible = "regulator-fixed";
+		regulator-name = "D3.3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	hdmi-out {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con: endpoint {
+				remote-endpoint = <&adv7511_out>;
+			};
+		};
+	};
+
+	lvds-decoder {
+		compatible = "thine,thc63lvd1024";
+		vcc-supply = <&d3_3v>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				thc63lvd1024_in: endpoint {
+					remote-endpoint = <&lvds0_out>;
+				};
+			};
+
+			port@2 {
+				reg = <2>;
+				thc63lvd1024_out: endpoint {
+					remote-endpoint = <&adv7511_in>;
+				};
+			};
+		};
+	};
+
+	memory@48000000 {
+		device_type = "memory";
+		/* first 128MB is reserved for secure area. */
+		reg = <0 0x48000000 0 0x78000000>;
+	};
+
+	vddq_vin01: regulator-1 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDQ_VIN01";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	x1_clk: x1-clock {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <148500000>;
+	};
+};
+
+&canfd {
+	pinctrl-0 = <&canfd0_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	channel0 {
+		status = "okay";
+	};
+};
+
+&csi40 {
+	status = "okay";
+
+	ports {
+		port@0 {
+			csi40_in: endpoint {
+				clock-lanes = <0>;
+				data-lanes = <1 2 3 4>;
+				remote-endpoint = <&max9286_out0>;
+			};
+		};
+	};
+};
+
+&csi41 {
+	status = "okay";
+
+	ports {
+		port@0 {
+			csi41_in: endpoint {
+				clock-lanes = <0>;
+				data-lanes = <1 2 3 4>;
+				remote-endpoint = <&max9286_out1>;
+			};
+		};
+	};
+};
+
+&du {
+	clocks = <&cpg CPG_MOD 724>,
+		 <&x1_clk>;
+	clock-names = "du.0", "dclkin.0";
+	status = "okay";
+};
+
+&extal_clk {
+	clock-frequency = <16666666>;
+};
+
+&extalr_clk {
+	clock-frequency = <32768>;
+};
+
+&gether {
+	pinctrl-0 = <&gether_pins>;
+	pinctrl-names = "default";
+
+	phy-mode = "rgmii-id";
+	phy-handle = <&phy0>;
+	renesas,no-ether-link;
+	status = "okay";
+
+	phy0: ethernet-phy@0 {
+		compatible = "ethernet-phy-id0022.1622",
+			     "ethernet-phy-ieee802.3-c22";
+		rxc-skew-ps = <1500>;
+		reg = <0>;
+		interrupt-parent = <&gpio4>;
+		interrupts = <23 IRQ_TYPE_LEVEL_LOW>;
+		reset-gpios = <&gpio4 22 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&i2c0 {
+	pinctrl-0 = <&i2c0_pins>;
+	pinctrl-names = "default";
+
+	status = "okay";
+	clock-frequency = <400000>;
+
+	io_expander0: gpio@20 {
+		compatible = "onnn,pca9654";
+		reg = <0x20>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	io_expander1: gpio@21 {
+		compatible = "onnn,pca9654";
+		reg = <0x21>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	hdmi@39 {
+		compatible = "adi,adv7511w";
+		reg = <0x39>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <20 IRQ_TYPE_LEVEL_LOW>;
+		avdd-supply = <&d1_8v>;
+		dvdd-supply = <&d1_8v>;
+		pvdd-supply = <&d1_8v>;
+		bgvdd-supply = <&d1_8v>;
+		dvdd-3v-supply = <&d3_3v>;
+
+		adi,input-depth = <8>;
+		adi,input-colorspace = "rgb";
+		adi,input-clock = "1x";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				adv7511_in: endpoint {
+					remote-endpoint = <&thc63lvd1024_out>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+				adv7511_out: endpoint {
+					remote-endpoint = <&hdmi_con>;
+				};
+			};
+		};
+	};
+};
+
+&i2c1 {
+	pinctrl-0 = <&i2c1_pins>;
+	pinctrl-names = "default";
+
+	status = "okay";
+	clock-frequency = <400000>;
+
+	gmsl0: gmsl-deserializer@48 {
+		compatible = "maxim,max9286";
+		reg = <0x48>;
+
+		maxim,gpio-poc = <0 GPIO_ACTIVE_LOW>;
+		enable-gpios = <&io_expander0 0 GPIO_ACTIVE_HIGH>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+			};
+
+			port@1 {
+				reg = <1>;
+			};
+
+			port@2 {
+				reg = <2>;
+			};
+
+			port@3 {
+				reg = <3>;
+			};
+
+			port@4 {
+				reg = <4>;
+				max9286_out0: endpoint {
+					clock-lanes = <0>;
+					data-lanes = <1 2 3 4>;
+					remote-endpoint = <&csi40_in>;
+				};
+			};
+		};
+
+		i2c-mux {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			i2c@0 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0>;
+
+				status = "disabled";
+			};
+
+			i2c@1 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <1>;
+
+				status = "disabled";
+			};
+
+			i2c@2 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <2>;
+
+				status = "disabled";
+			};
+
+			i2c@3 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <3>;
+
+				status = "disabled";
+			};
+		};
+	};
+
+	gmsl1: gmsl-deserializer@4a {
+		compatible = "maxim,max9286";
+		reg = <0x4a>;
+
+		maxim,gpio-poc = <0 GPIO_ACTIVE_LOW>;
+		enable-gpios = <&io_expander1 0 GPIO_ACTIVE_HIGH>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+			};
+
+			port@1 {
+				reg = <1>;
+			};
+
+			port@2 {
+				reg = <2>;
+			};
+
+			port@3 {
+				reg = <3>;
+			};
+
+			port@4 {
+				reg = <4>;
+				max9286_out1: endpoint {
+					clock-lanes = <0>;
+					data-lanes = <1 2 3 4>;
+					remote-endpoint = <&csi41_in>;
+				};
+			};
+		};
+
+		i2c-mux {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			i2c@0 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0>;
+
+				status = "disabled";
+			};
+
+			i2c@1 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <1>;
+
+				status = "disabled";
+			};
+
+			i2c@2 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <2>;
+
+				status = "disabled";
+			};
+
+			i2c@3 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <3>;
+
+				status = "disabled";
+			};
+		};
+	};
+};
+
+&lvds0 {
+	status = "okay";
+
+	ports {
+		port@1 {
+			lvds0_out: endpoint {
+				remote-endpoint = <&thc63lvd1024_in>;
+			};
+		};
+	};
+};
+
+&mmc0 {
+	pinctrl-0 = <&mmc_pins>;
+	pinctrl-1 = <&mmc_pins>;
+	pinctrl-names = "default", "state_uhs";
+
+	vmmc-supply = <&d3_3v>;
+	vqmmc-supply = <&vddq_vin01>;
+	mmc-hs200-1_8v;
+	bus-width = <8>;
+	no-sd;
+	no-sdio;
+	non-removable;
+	status = "okay";
+};
+
+&pciec {
+	status = "okay";
+};
+
+&pcie_bus_clk {
+	clock-frequency = <100000000>;
+};
+
+&pcie_phy {
+	status = "okay";
+};
+
+&pfc {
+	canfd0_pins: canfd0 {
+		groups = "canfd0_data_a";
+		function = "canfd0";
+	};
+
+	gether_pins: gether {
+		groups = "gether_mdio_a", "gether_rgmii",
+			 "gether_txcrefclk", "gether_txcrefclk_mega";
+		function = "gether";
+	};
+
+	i2c0_pins: i2c0 {
+		groups = "i2c0";
+		function = "i2c0";
+	};
+
+	i2c1_pins: i2c1 {
+		groups = "i2c1";
+		function = "i2c1";
+	};
+
+	mmc_pins: mmc {
+		groups = "mmc_data8", "mmc_ctrl", "mmc_ds";
+		function = "mmc";
+		power-source = <1800>;
+	};
+
+	qspi0_pins: qspi0 {
+		groups = "qspi0_ctrl", "qspi0_data4";
+		function = "qspi0";
+	};
+
+	scif0_pins: scif0 {
+		groups = "scif0_data";
+		function = "scif0";
+	};
+
+	scif_clk_pins: scif_clk {
+		groups = "scif_clk_b";
+		function = "scif_clk";
+	};
+};
+
+&rpc {
+	pinctrl-0 = <&qspi0_pins>;
+	pinctrl-names = "default";
+
+	status = "okay";
+
+	flash@0 {
+		compatible = "spansion,s25fs512s", "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <50000000>;
+		spi-rx-bus-width = <4>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			bootparam@0 {
+				reg = <0x00000000 0x040000>;
+				read-only;
+			};
+			cr7@40000 {
+				reg = <0x00040000 0x080000>;
+				read-only;
+			};
+			cert_header_sa3@c0000 {
+				reg = <0x000c0000 0x080000>;
+				read-only;
+			};
+			bl2@140000 {
+				reg = <0x00140000 0x040000>;
+				read-only;
+			};
+			cert_header_sa6@180000 {
+				reg = <0x00180000 0x040000>;
+				read-only;
+			};
+			bl31@1c0000 {
+				reg = <0x001c0000 0x460000>;
+				read-only;
+			};
+			uboot@640000 {
+				reg = <0x00640000 0x0c0000>;
+				read-only;
+			};
+			uboot-env@700000 {
+				reg = <0x00700000 0x040000>;
+				read-only;
+			};
+			dtb@740000 {
+				reg = <0x00740000 0x080000>;
+			};
+			kernel@7c0000 {
+				reg = <0x007c0000 0x1400000>;
+			};
+			user@1bc0000 {
+				reg = <0x01bc0000 0x2440000>;
+			};
+		};
+	};
+};
+
+&rwdt {
+	timeout-sec = <60>;
+	status = "okay";
+};
+
+&scif0 {
+	pinctrl-0 = <&scif0_pins>, <&scif_clk_pins>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&scif_clk {
+	clock-frequency = <14745600>;
+};
diff --git a/arch/arm64/boot/dts/renesas/draak-ebisu-panel-aa104xd12.dts b/arch/arm64/boot/dts/renesas/draak-ebisu-panel-aa104xd12.dts
new file mode 100644
index 000000000000..258f8668ca36
--- /dev/null
+++ b/arch/arm64/boot/dts/renesas/draak-ebisu-panel-aa104xd12.dts
@@ -0,0 +1,36 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device Tree overlay for the AA104XD12 panel connected to LVDS1 on a Draak or
+ * Ebisu board
+ *
+ * Copyright 2021 Ideas on Board Oy
+ */
+
+/dts-v1/;
+/plugin/;
+
+&{/} {
+#include "panel-aa104xd12.dtsi"
+};
+
+&{/panel} {
+	backlight = <&backlight>;
+
+	port {
+		panel_in: endpoint {
+			remote-endpoint = <&lvds1_out>;
+		};
+	};
+};
+
+&lvds1 {
+	status = "okay";
+
+	ports {
+		port@1 {
+			lvds1_out: endpoint {
+				remote-endpoint = <&panel_in>;
+			};
+		};
+	};
+};
diff --git a/arch/arm64/boot/dts/renesas/draak.dtsi b/arch/arm64/boot/dts/renesas/draak.dtsi
index eb0327c0df48..ef3bb835d5c0 100644
--- a/arch/arm64/boot/dts/renesas/draak.dtsi
+++ b/arch/arm64/boot/dts/renesas/draak.dtsi
@@ -285,7 +285,7 @@
 
 	ports {
 		port@0 {
-			endpoint {
+			du_out_rgb: endpoint {
 				remote-endpoint = <&adv7123_in>;
 			};
 		};
@@ -541,6 +541,12 @@
 		function = "pwm1";
 	};
 
+	rpc_pins: rpc {
+		groups = "rpc_clk2", "rpc_ctrl", "rpc_data", "rpc_reset",
+			 "rpc_int";
+		function = "rpc";
+	};
+
 	scif2_pins: scif2 {
 		groups = "scif2_data";
 		function = "scif2";
@@ -624,7 +630,59 @@
 				bitclock-master = <&rsnd_for_ak4613>;
 				frame-master = <&rsnd_for_ak4613>;
 				playback = <&ssi3>, <&src5>, <&dvc0>;
-				capture  = <&ssi4>, <&src6>, <&dvc1>;
+				capture = <&ssi4>, <&src6>, <&dvc1>;
+			};
+		};
+	};
+};
+
+&rpc {
+	pinctrl-0 = <&rpc_pins>;
+	pinctrl-names = "default";
+
+	/* Left disabled.  To be enabled by firmware when unlocked. */
+
+	flash@0 {
+		compatible = "cypress,hyperflash", "cfi-flash";
+		reg = <0>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			bootparam@0 {
+				reg = <0x00000000 0x040000>;
+				read-only;
+			};
+			bl2@40000 {
+				reg = <0x00040000 0x140000>;
+				read-only;
+			};
+			cert_header_sa6@180000 {
+				reg = <0x00180000 0x040000>;
+				read-only;
+			};
+			bl31@1c0000 {
+				reg = <0x001c0000 0x040000>;
+				read-only;
+			};
+			tee@200000 {
+				reg = <0x00200000 0x440000>;
+				read-only;
+			};
+			uboot@640000 {
+				reg = <0x00640000 0x100000>;
+				read-only;
+			};
+			dtb@740000 {
+				reg = <0x00740000 0x080000>;
+			};
+			kernel@7c0000 {
+				reg = <0x007c0000 0x1400000>;
+			};
+			user@1bc0000 {
+				reg = <0x01bc0000 0x2440000>;
 			};
 		};
 	};
diff --git a/arch/arm64/boot/dts/renesas/ebisu.dtsi b/arch/arm64/boot/dts/renesas/ebisu.dtsi
index 67231c8576c5..bbc29452d1be 100644
--- a/arch/arm64/boot/dts/renesas/ebisu.dtsi
+++ b/arch/arm64/boot/dts/renesas/ebisu.dtsi
@@ -13,6 +13,14 @@
 	compatible = "renesas,ebisu";
 
 	aliases {
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+		i2c2 = &i2c2;
+		i2c3 = &i2c3;
+		i2c4 = &i2c4;
+		i2c5 = &i2c5;
+		i2c6 = &i2c6;
+		i2c7 = &i2c7;
 		serial0 = &scif2;
 		ethernet0 = &avb;
 		mmc0 = &sdhi3;
@@ -145,7 +153,7 @@
 		reg = <0x0 0x48000000 0x0 0x38000000>;
 	};
 
-	reg_1p8v: regulator0 {
+	reg_1p8v: regulator-1p8v {
 		compatible = "regulator-fixed";
 		regulator-name = "fixed-1.8V";
 		regulator-min-microvolt = <1800000>;
@@ -154,7 +162,7 @@
 		regulator-always-on;
 	};
 
-	reg_3p3v: regulator1 {
+	reg_3p3v: regulator-3p3v {
 		compatible = "regulator-fixed";
 		regulator-name = "fixed-3.3V";
 		regulator-min-microvolt = <3300000>;
@@ -163,7 +171,7 @@
 		regulator-always-on;
 	};
 
-	reg_12p0v: regulator2 {
+	reg_12p0v: regulator-12p0v {
 		compatible = "regulator-fixed";
 		regulator-name = "D12.0V";
 		regulator-min-microvolt = <12000000>;
@@ -356,7 +364,7 @@
 
 	ports {
 		port@0 {
-			endpoint {
+			du_out_rgb: endpoint {
 				remote-endpoint = <&adv7123_in>;
 			};
 		};
@@ -600,6 +608,12 @@
 		function = "pwm5";
 	};
 
+	rpc_pins: rpc {
+		groups = "rpc_clk2", "rpc_ctrl", "rpc_data", "rpc_reset",
+			 "rpc_int";
+		function = "rpc";
+	};
+
 	scif2_pins: scif2 {
 		groups = "scif2_data_a";
 		function = "scif2";
@@ -705,12 +719,64 @@
 	rcar_sound,dai {
 		dai0 {
 			playback = <&ssi0>, <&src0>, <&dvc0>;
-			capture  = <&ssi1>, <&src1>, <&dvc1>;
+			capture = <&ssi1>, <&src1>, <&dvc1>;
 		};
 	};
 
 };
 
+&rpc {
+	pinctrl-0 = <&rpc_pins>;
+	pinctrl-names = "default";
+
+	/* Left disabled.  To be enabled by firmware when unlocked. */
+
+	flash@0 {
+		compatible = "cypress,hyperflash", "cfi-flash";
+		reg = <0>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			bootparam@0 {
+				reg = <0x00000000 0x040000>;
+				read-only;
+			};
+			bl2@40000 {
+				reg = <0x00040000 0x140000>;
+				read-only;
+			};
+			cert_header_sa6@180000 {
+				reg = <0x00180000 0x040000>;
+				read-only;
+			};
+			bl31@1c0000 {
+				reg = <0x001c0000 0x040000>;
+				read-only;
+			};
+			tee@200000 {
+				reg = <0x00200000 0x440000>;
+				read-only;
+			};
+			uboot@640000 {
+				reg = <0x00640000 0x100000>;
+				read-only;
+			};
+			dtb@740000 {
+				reg = <0x00740000 0x080000>;
+			};
+			kernel@7c0000 {
+				reg = <0x007c0000 0x1400000>;
+			};
+			user@1bc0000 {
+				reg = <0x01bc0000 0x2440000>;
+			};
+		};
+	};
+};
+
 &rwdt {
 	timeout-sec = <60>;
 	status = "okay";
diff --git a/arch/arm64/boot/dts/renesas/gmsl-cameras.dtsi b/arch/arm64/boot/dts/renesas/gmsl-cameras.dtsi
new file mode 100644
index 000000000000..d45f072f8cdf
--- /dev/null
+++ b/arch/arm64/boot/dts/renesas/gmsl-cameras.dtsi
@@ -0,0 +1,332 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2017 Ideas on Board <kieran.bingham@ideasonboard.com>
+ * Copyright (C) 2021 Jacopo Mondi <jacopo+renesas@jmondi.org>
+ *
+ * Device Tree Source (overlay) that describes GMSL camera connected to
+ * Fakra connectors for the Eagle V3M and Condor V3H (and compatible) boards.
+ *
+ * The following cameras are currently supported: RDACM20 and RDACM21.
+ *
+ * The board .dts file that include this has to select which cameras are in use
+ * by specifying the camera model with:
+ *
+ * #define GMSL_CAMERA_RDACM20
+ * or
+ * #define GMSL_CAMERA_RDACM21
+ *
+ * And which cameras are connected to the board by defining:
+ * for GMSL channel 0:
+ *	   #define GMSL_CAMERA_0
+ *	   #define GMSL_CAMERA_1
+ *	   #define GMSL_CAMERA_2
+ *	   #define GMSL_CAMERA_3
+ *
+ * for GMSL channel 1:
+ *	   #define GMSL_CAMERA_4
+ *	   #define GMSL_CAMERA_5
+ *	   #define GMSL_CAMERA_6
+ *	   #define GMSL_CAMERA_7
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+
+/* Validate the board file settings. */
+#if !defined(GMSL_CAMERA_RDACM20) && !defined(GMSL_CAMERA_RDACM21)
+#error "Camera model should be defined by the board file"
+#endif
+
+#if defined(GMSL_CAMERA_RDACM20) && defined(GMSL_CAMERA_RDACM21)
+#error "A single camera model should be selected"
+#endif
+
+#if !defined(GMSL_CAMERA_0) && !defined(GMSL_CAMERA_1) && \
+    !defined(GMSL_CAMERA_2) && !defined(GMSL_CAMERA_3) && \
+    !defined(GMSL_CAMERA_4) && !defined(GMSL_CAMERA_5) && \
+    !defined(GMSL_CAMERA_6) && !defined(GMSL_CAMERA_7)
+#error "At least one camera should be selected"
+#endif
+
+/* Deduce from the enabled cameras which GMSL channels are active. */
+#if defined(GMSL_CAMERA_0) || defined(GMSL_CAMERA_1) || \
+    defined(GMSL_CAMERA_2) || defined(GMSL_CAMERA_3)
+#define GMSL_0
+#endif
+
+#if defined(GMSL_CAMERA_4) || defined(GMSL_CAMERA_5) || \
+    defined(GMSL_CAMERA_6) || defined(GMSL_CAMERA_7)
+#define GMSL_1
+#endif
+
+/* Deduce the camera model compatible string. */
+#if defined(GMSL_CAMERA_RDACM20)
+#define GMSL_CAMERA_MODEL "imi,rdacm20"
+#elif defined(GMSL_CAMERA_RDACM21)
+#define GMSL_CAMERA_MODEL "imi,rdacm21"
+#endif
+
+#ifdef GMSL_0
+&vin0 {
+	status = "okay";
+};
+
+&vin1 {
+	status = "okay";
+};
+
+&vin2 {
+	status = "okay";
+};
+
+&vin3 {
+	status = "okay";
+};
+
+&gmsl0 {
+	status = "okay";
+
+#if defined(GMSL_CAMERA_RDACM21)
+	maxim,reverse-channel-microvolt = <100000>;
+#endif
+
+	ports {
+#ifdef GMSL_CAMERA_0
+		port@0 {
+			max9286_in0: endpoint {
+				remote-endpoint = <&fakra_con0>;
+			};
+		};
+#endif
+
+#ifdef GMSL_CAMERA_1
+		port@1 {
+			max9286_in1: endpoint{
+				remote-endpoint = <&fakra_con1>;
+			};
+
+		};
+#endif
+
+#ifdef GMSL_CAMERA_2
+		port@2 {
+			max9286_in2: endpoint {
+				remote-endpoint = <&fakra_con2>;
+			};
+
+		};
+#endif
+
+#ifdef GMSL_CAMERA_3
+		port@3 {
+			max9286_in3: endpoint {
+				remote-endpoint = <&fakra_con3>;
+			};
+
+		};
+#endif
+	};
+
+	i2c-mux {
+#ifdef GMSL_CAMERA_0
+		i2c@0 {
+			status = "okay";
+
+			camera@51 {
+				compatible = GMSL_CAMERA_MODEL;
+				reg = <0x51>, <0x61>;
+
+				port {
+					fakra_con0: endpoint {
+						remote-endpoint = <&max9286_in0>;
+					};
+				};
+			};
+		};
+#endif
+
+#ifdef GMSL_CAMERA_1
+		i2c@1 {
+			status = "okay";
+
+			camera@52 {
+				compatible = GMSL_CAMERA_MODEL;
+				reg = <0x52>, <0x62>;
+
+				port {
+					fakra_con1: endpoint {
+						remote-endpoint = <&max9286_in1>;
+					};
+				};
+			};
+		};
+#endif
+
+#ifdef GMSL_CAMERA_2
+		i2c@2 {
+			status = "okay";
+
+			camera@53 {
+				compatible = GMSL_CAMERA_MODEL;
+				reg = <0x53>, <0x63>;
+
+				port {
+					fakra_con2: endpoint {
+						remote-endpoint = <&max9286_in2>;
+					};
+				};
+			};
+		};
+#endif
+
+#ifdef GMSL_CAMERA_3
+		i2c@3 {
+			status = "okay";
+
+			camera@54 {
+				compatible = GMSL_CAMERA_MODEL;
+				reg = <0x54>, <0x64>;
+
+				port {
+					fakra_con3: endpoint {
+						remote-endpoint = <&max9286_in3>;
+					};
+				};
+			};
+		};
+#endif
+	};
+};
+#endif /* ifdef GMSL_0 */
+
+#ifdef GMSL_1
+&vin4 {
+	status = "okay";
+};
+
+&vin5 {
+	status = "okay";
+};
+
+&vin6 {
+	status = "okay";
+};
+
+&vin7 {
+	status = "okay";
+};
+
+&gmsl1 {
+	status = "okay";
+
+#if defined(GMSL_CAMERA_RDACM21)
+	maxim,reverse-channel-microvolt = <100000>;
+#endif
+
+	ports {
+#ifdef GMSL_CAMERA_4
+		port@0 {
+			max9286_in4: endpoint {
+				remote-endpoint = <&fakra_con4>;
+			};
+		};
+#endif
+
+#ifdef GMSL_CAMERA_5
+		port@1 {
+			max9286_in5: endpoint{
+				remote-endpoint = <&fakra_con5>;
+			};
+
+		};
+#endif
+
+#ifdef GMSL_CAMERA_6
+		port@2 {
+			max9286_in6: endpoint {
+				remote-endpoint = <&fakra_con6>;
+			};
+
+		};
+#endif
+
+#ifdef GMSL_CAMERA_7
+		port@3 {
+			max9286_in7: endpoint {
+				remote-endpoint = <&fakra_con7>;
+			};
+
+		};
+#endif
+	};
+
+	i2c-mux {
+#ifdef GMSL_CAMERA_4
+		i2c@0 {
+			status = "okay";
+
+			camera@55 {
+				compatible = GMSL_CAMERA_MODEL;
+				reg = <0x55>, <0x65>;
+
+				port {
+					fakra_con4: endpoint {
+						remote-endpoint = <&max9286_in4>;
+					};
+				};
+			};
+		};
+#endif
+
+#ifdef GMSL_CAMERA_5
+		i2c@1 {
+			status = "okay";
+
+			camera@56 {
+				compatible = GMSL_CAMERA_MODEL;
+				reg = <0x56>, <0x66>;
+
+				port {
+					fakra_con5: endpoint {
+						remote-endpoint = <&max9286_in5>;
+					};
+				};
+			};
+		};
+#endif
+
+#ifdef GMSL_CAMERA_6
+		i2c@2 {
+			status = "okay";
+
+			camera@57 {
+				compatible = GMSL_CAMERA_MODEL;
+				reg = <0x57>, <0x67>;
+
+				port {
+					fakra_con6: endpoint {
+						remote-endpoint = <&max9286_in6>;
+					};
+				};
+			};
+		};
+#endif
+
+#ifdef GMSL_CAMERA_7
+		i2c@3 {
+			status = "okay";
+
+			camera@58 {
+				compatible = GMSL_CAMERA_MODEL;
+				reg = <0x58>, <0x68>;
+
+				port {
+					fakra_con7: endpoint {
+						remote-endpoint = <&max9286_in7>;
+					};
+				};
+			};
+		};
+#endif
+	};
+};
+#endif /* ifdef GMSL_1 */
diff --git a/arch/arm64/boot/dts/renesas/hihope-common.dtsi b/arch/arm64/boot/dts/renesas/hihope-common.dtsi
index 0c7e6f790590..83104af2813e 100644
--- a/arch/arm64/boot/dts/renesas/hihope-common.dtsi
+++ b/arch/arm64/boot/dts/renesas/hihope-common.dtsi
@@ -10,6 +10,14 @@
 
 / {
 	aliases {
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+		i2c2 = &i2c2;
+		i2c3 = &i2c3;
+		i2c4 = &i2c4;
+		i2c5 = &i2c5;
+		i2c6 = &i2c6;
+		i2c7 = &iic_pmic;
 		serial0 = &scif2;
 		serial1 = &hscif0;
 		mmc0 = &sdhi3;
@@ -53,7 +61,7 @@
 		};
 	};
 
-	reg_1p8v: regulator0 {
+	reg_1p8v: regulator-1p8v {
 		compatible = "regulator-fixed";
 		regulator-name = "fixed-1.8V";
 		regulator-min-microvolt = <1800000>;
@@ -62,7 +70,7 @@
 		regulator-always-on;
 	};
 
-	reg_3p3v: regulator1 {
+	reg_3p3v: regulator-3p3v {
 		compatible = "regulator-fixed";
 		regulator-name = "fixed-3.3V";
 		regulator-min-microvolt = <3300000>;
@@ -140,7 +148,7 @@
 };
 
 &gpio6 {
-	usb1-reset {
+	usb1-reset-hog {
 		gpio-hog;
 		gpios = <10 GPIO_ACTIVE_LOW>;
 		output-low;
diff --git a/arch/arm64/boot/dts/renesas/hihope-rzg2-ex-lvds.dtsi b/arch/arm64/boot/dts/renesas/hihope-rzg2-ex-lvds.dtsi
index 40c5e8d6d841..d66d17e34694 100644
--- a/arch/arm64/boot/dts/renesas/hihope-rzg2-ex-lvds.dtsi
+++ b/arch/arm64/boot/dts/renesas/hihope-rzg2-ex-lvds.dtsi
@@ -20,7 +20,7 @@
 	 * When GP1_20 is LOW LVDS0 is connected to the LVDS connector
 	 * When GP1_20 is HIGH LVDS0 is connected to the LT8918L
 	 */
-	lvds-connector-en-gpio {
+	lvds-connector-en-hog {
 		gpio-hog;
 		gpios = <20 GPIO_ACTIVE_HIGH>;
 		output-low;
diff --git a/arch/arm64/boot/dts/renesas/panel-aa104xd12.dtsi b/arch/arm64/boot/dts/renesas/panel-aa104xd12.dtsi
new file mode 100644
index 000000000000..4b1f0982b9e4
--- /dev/null
+++ b/arch/arm64/boot/dts/renesas/panel-aa104xd12.dtsi
@@ -0,0 +1,30 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Common file for the AA104XD12 panel connected to Renesas R-Car Gen3 boards.
+ *
+ * Copyright (C) 2014 Renesas Electronics Corp.
+ */
+
+panel {
+	compatible = "mitsubishi,aa104xd12", "panel-lvds";
+
+	width-mm = <210>;
+	height-mm = <158>;
+	data-mapping = "jeida-18";
+
+	panel-timing {
+		/* 1024x768 @65Hz */
+		clock-frequency = <65000000>;
+		hactive = <1024>;
+		vactive = <768>;
+		hsync-len = <136>;
+		hfront-porch = <20>;
+		hback-porch = <160>;
+		vfront-porch = <3>;
+		vback-porch = <29>;
+		vsync-len = <6>;
+	};
+
+	port {
+	};
+};
diff --git a/arch/arm64/boot/dts/renesas/r8a774a1-beacon-rzg2m-kit.dts b/arch/arm64/boot/dts/renesas/r8a774a1-beacon-rzg2m-kit.dts
index 3cf2e076940f..9ae67263c0df 100644
--- a/arch/arm64/boot/dts/renesas/r8a774a1-beacon-rzg2m-kit.dts
+++ b/arch/arm64/boot/dts/renesas/r8a774a1-beacon-rzg2m-kit.dts
@@ -14,6 +14,14 @@
 	compatible = "beacon,beacon-rzg2m", "renesas,r8a774a1";
 
 	aliases {
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+		i2c2 = &i2c2;
+		i2c3 = &i2c3;
+		i2c4 = &i2c4;
+		i2c5 = &i2c5;
+		i2c6 = &i2c6;
+		i2c7 = &iic_pmic;
 		serial0 = &scif2;
 		serial1 = &hscif0;
 		serial2 = &hscif1;
diff --git a/arch/arm64/boot/dts/renesas/r8a774a1.dtsi b/arch/arm64/boot/dts/renesas/r8a774a1.dtsi
index 6f4fffacfca2..7e643243c3be 100644
--- a/arch/arm64/boot/dts/renesas/r8a774a1.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a774a1.dtsi
@@ -17,17 +17,6 @@
 	#address-cells = <2>;
 	#size-cells = <2>;
 
-	aliases {
-		i2c0 = &i2c0;
-		i2c1 = &i2c1;
-		i2c2 = &i2c2;
-		i2c3 = &i2c3;
-		i2c4 = &i2c4;
-		i2c5 = &i2c5;
-		i2c6 = &i2c6;
-		i2c7 = &iic_pmic;
-	};
-
 	/*
 	 * The external audio clocks are configured as 0 Hz fixed frequency
 	 * clocks by default.
@@ -58,7 +47,7 @@
 		clock-frequency = <0>;
 	};
 
-	cluster0_opp: opp_table0 {
+	cluster0_opp: opp-table-0 {
 		compatible = "operating-points-v2";
 		opp-shared;
 
@@ -80,7 +69,7 @@
 		};
 	};
 
-	cluster1_opp: opp_table1 {
+	cluster1_opp: opp-table-1 {
 		compatible = "operating-points-v2";
 		opp-shared;
 
@@ -283,6 +272,7 @@
 			compatible = "renesas,r8a774a1-wdt",
 				     "renesas,rcar-gen3-wdt";
 			reg = <0 0xe6020000 0 0x0c>;
+			interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 402>;
 			power-domains = <&sysc R8A774A1_PD_ALWAYS_ON>;
 			resets = <&cpg 402>;
@@ -1178,6 +1168,7 @@
 			reg = <0 0xe66c0000 0 0x8000>;
 			interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "ch_int", "g_int";
 			clocks = <&cpg CPG_MOD 914>,
 				 <&cpg CPG_CORE R8A774A1_CLK_CANFD>,
 				 <&can_clk>;
@@ -1698,12 +1689,12 @@
 			 * clkout	: #clock-cells = <0>;	<&rcar_sound>;
 			 * clkout0/1/2/3: #clock-cells = <1>;	<&rcar_sound N>;
 			 */
-			compatible =  "renesas,rcar_sound-r8a774a1", "renesas,rcar_sound-gen3";
-			reg =	<0 0xec500000 0 0x1000>, /* SCU */
-				<0 0xec5a0000 0 0x100>,  /* ADG */
-				<0 0xec540000 0 0x1000>, /* SSIU */
-				<0 0xec541000 0 0x280>,  /* SSI */
-				<0 0xec760000 0 0x200>;  /* Audio DMAC peri peri*/
+			compatible = "renesas,rcar_sound-r8a774a1", "renesas,rcar_sound-gen3";
+			reg = <0 0xec500000 0 0x1000>, /* SCU */
+			      <0 0xec5a0000 0 0x100>,  /* ADG */
+			      <0 0xec540000 0 0x1000>, /* SSIU */
+			      <0 0xec541000 0 0x280>,  /* SSI */
+			      <0 0xec760000 0 0x200>;  /* Audio DMAC peri peri*/
 			reg-names = "scu", "adg", "ssiu", "ssi", "audmapp";
 
 			clocks = <&cpg CPG_MOD 1005>,
@@ -2010,7 +2001,7 @@
 					dma-names = "rx", "tx";
 				};
 				ssiu40: ssiu-32 {
-					dmas =	<&audma0 0x71>, <&audma1 0x72>;
+					dmas = <&audma0 0x71>, <&audma1 0x72>;
 					dma-names = "rx", "tx";
 				};
 				ssiu41: ssiu-33 {
@@ -2276,7 +2267,8 @@
 				     "renesas,rcar-gen3-sdhi";
 			reg = <0 0xee100000 0 0x2000>;
 			interrupts = <GIC_SPI 165 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&cpg CPG_MOD 314>;
+			clocks = <&cpg CPG_MOD 314>, <&cpg CPG_CORE R8A774A1_CLK_SD0H>;
+			clock-names = "core", "clkh";
 			max-frequency = <200000000>;
 			power-domains = <&sysc R8A774A1_PD_ALWAYS_ON>;
 			resets = <&cpg 314>;
@@ -2288,7 +2280,8 @@
 				     "renesas,rcar-gen3-sdhi";
 			reg = <0 0xee120000 0 0x2000>;
 			interrupts = <GIC_SPI 166 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&cpg CPG_MOD 313>;
+			clocks = <&cpg CPG_MOD 313>, <&cpg CPG_CORE R8A774A1_CLK_SD1H>;
+			clock-names = "core", "clkh";
 			max-frequency = <200000000>;
 			power-domains = <&sysc R8A774A1_PD_ALWAYS_ON>;
 			resets = <&cpg 313>;
@@ -2300,7 +2293,8 @@
 				     "renesas,rcar-gen3-sdhi";
 			reg = <0 0xee140000 0 0x2000>;
 			interrupts = <GIC_SPI 167 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&cpg CPG_MOD 312>;
+			clocks = <&cpg CPG_MOD 312>, <&cpg CPG_CORE R8A774A1_CLK_SD2H>;
+			clock-names = "core", "clkh";
 			max-frequency = <200000000>;
 			power-domains = <&sysc R8A774A1_PD_ALWAYS_ON>;
 			resets = <&cpg 312>;
@@ -2312,7 +2306,8 @@
 				     "renesas,rcar-gen3-sdhi";
 			reg = <0 0xee160000 0 0x2000>;
 			interrupts = <GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&cpg CPG_MOD 311>;
+			clocks = <&cpg CPG_MOD 311>, <&cpg CPG_CORE R8A774A1_CLK_SD3H>;
+			clock-names = "core", "clkh";
 			max-frequency = <200000000>;
 			power-domains = <&sysc R8A774A1_PD_ALWAYS_ON>;
 			resets = <&cpg 311>;
@@ -2328,7 +2323,6 @@
 			reg-names = "regs", "dirmap", "wbuf";
 			interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 917>;
-			clock-names = "rpc";
 			power-domains = <&sysc R8A774A1_PD_ALWAYS_ON>;
 			resets = <&cpg 917>;
 			#address-cells = <1>;
@@ -2733,8 +2727,6 @@
 
 				port@0 {
 					reg = <0>;
-					du_out_rgb: endpoint {
-					};
 				};
 				port@1 {
 					reg = <1>;
@@ -2771,8 +2763,6 @@
 				};
 				port@1 {
 					reg = <1>;
-					lvds0_out: endpoint {
-					};
 				};
 			};
 		};
@@ -2784,7 +2774,7 @@
 	};
 
 	thermal-zones {
-		sensor_thermal1: sensor-thermal1 {
+		sensor1_thermal: sensor1-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 			thermal-sensors = <&tsc 0>;
@@ -2799,7 +2789,7 @@
 			};
 		};
 
-		sensor_thermal2: sensor-thermal2 {
+		sensor2_thermal: sensor2-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 			thermal-sensors = <&tsc 1>;
@@ -2814,7 +2804,7 @@
 			};
 		};
 
-		sensor_thermal3: sensor-thermal3 {
+		sensor3_thermal: sensor3-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 			thermal-sensors = <&tsc 2>;
diff --git a/arch/arm64/boot/dts/renesas/r8a774b1-beacon-rzg2n-kit.dts b/arch/arm64/boot/dts/renesas/r8a774b1-beacon-rzg2n-kit.dts
index 3c0d59def8ee..89d708346ba8 100644
--- a/arch/arm64/boot/dts/renesas/r8a774b1-beacon-rzg2n-kit.dts
+++ b/arch/arm64/boot/dts/renesas/r8a774b1-beacon-rzg2n-kit.dts
@@ -11,7 +11,7 @@
 
 / {
 	model = "Beacon Embedded Works RZ/G2N Development Kit";
-	compatible =	"beacon,beacon-rzg2n", "renesas,r8a774b1";
+	compatible = "beacon,beacon-rzg2n", "renesas,r8a774b1";
 
 	aliases {
 		serial0 = &scif2;
diff --git a/arch/arm64/boot/dts/renesas/r8a774b1.dtsi b/arch/arm64/boot/dts/renesas/r8a774b1.dtsi
index 0f7bdfc90a0d..d541b48c7e38 100644
--- a/arch/arm64/boot/dts/renesas/r8a774b1.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a774b1.dtsi
@@ -47,7 +47,7 @@
 		clock-frequency = <0>;
 	};
 
-	cluster0_opp: opp_table0 {
+	cluster0_opp: opp-table-0 {
 		compatible = "operating-points-v2";
 		opp-shared;
 
@@ -156,6 +156,7 @@
 			compatible = "renesas,r8a774b1-wdt",
 				     "renesas,rcar-gen3-wdt";
 			reg = <0 0xe6020000 0 0x0c>;
+			interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 402>;
 			power-domains = <&sysc R8A774B1_PD_ALWAYS_ON>;
 			resets = <&cpg 402>;
@@ -1051,6 +1052,7 @@
 			reg = <0 0xe66c0000 0 0x8000>;
 			interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>,
 				   <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "ch_int", "g_int";
 			clocks = <&cpg CPG_MOD 914>,
 				 <&cpg CPG_CORE R8A774B1_CLK_CANFD>,
 				 <&can_clk>;
@@ -1571,7 +1573,7 @@
 			 * clkout	: #clock-cells = <0>;	<&rcar_sound>;
 			 * clkout0/1/2/3: #clock-cells = <1>;	<&rcar_sound N>;
 			 */
-			compatible =  "renesas,rcar_sound-r8a774b1", "renesas,rcar_sound-gen3";
+			compatible = "renesas,rcar_sound-r8a774b1", "renesas,rcar_sound-gen3";
 			reg = <0 0xec500000 0 0x1000>, /* SCU */
 			      <0 0xec5a0000 0 0x100>,  /* ADG */
 			      <0 0xec540000 0 0x1000>, /* SSIU */
@@ -1883,7 +1885,7 @@
 					dma-names = "rx", "tx";
 				};
 				ssiu40: ssiu-32 {
-					dmas =	<&audma0 0x71>, <&audma1 0x72>;
+					dmas = <&audma0 0x71>, <&audma1 0x72>;
 					dma-names = "rx", "tx";
 				};
 				ssiu41: ssiu-33 {
@@ -2133,7 +2135,8 @@
 				     "renesas,rcar-gen3-sdhi";
 			reg = <0 0xee100000 0 0x2000>;
 			interrupts = <GIC_SPI 165 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&cpg CPG_MOD 314>;
+			clocks = <&cpg CPG_MOD 314>, <&cpg CPG_CORE R8A774B1_CLK_SD0H>;
+			clock-names = "core", "clkh";
 			max-frequency = <200000000>;
 			power-domains = <&sysc R8A774B1_PD_ALWAYS_ON>;
 			resets = <&cpg 314>;
@@ -2145,7 +2148,8 @@
 				     "renesas,rcar-gen3-sdhi";
 			reg = <0 0xee120000 0 0x2000>;
 			interrupts = <GIC_SPI 166 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&cpg CPG_MOD 313>;
+			clocks = <&cpg CPG_MOD 313>, <&cpg CPG_CORE R8A774B1_CLK_SD1H>;
+			clock-names = "core", "clkh";
 			max-frequency = <200000000>;
 			power-domains = <&sysc R8A774B1_PD_ALWAYS_ON>;
 			resets = <&cpg 313>;
@@ -2157,7 +2161,8 @@
 				     "renesas,rcar-gen3-sdhi";
 			reg = <0 0xee140000 0 0x2000>;
 			interrupts = <GIC_SPI 167 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&cpg CPG_MOD 312>;
+			clocks = <&cpg CPG_MOD 312>, <&cpg CPG_CORE R8A774B1_CLK_SD2H>;
+			clock-names = "core", "clkh";
 			max-frequency = <200000000>;
 			power-domains = <&sysc R8A774B1_PD_ALWAYS_ON>;
 			resets = <&cpg 312>;
@@ -2169,7 +2174,8 @@
 				     "renesas,rcar-gen3-sdhi";
 			reg = <0 0xee160000 0 0x2000>;
 			interrupts = <GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&cpg CPG_MOD 311>;
+			clocks = <&cpg CPG_MOD 311>, <&cpg CPG_CORE R8A774B1_CLK_SD3H>;
+			clock-names = "core", "clkh";
 			max-frequency = <200000000>;
 			power-domains = <&sysc R8A774B1_PD_ALWAYS_ON>;
 			resets = <&cpg 311>;
@@ -2185,7 +2191,6 @@
 			reg-names = "regs", "dirmap", "wbuf";
 			interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 917>;
-			clock-names = "rpc";
 			power-domains = <&sysc R8A774B1_PD_ALWAYS_ON>;
 			resets = <&cpg 917>;
 			#address-cells = <1>;
@@ -2578,8 +2583,6 @@
 
 				port@0 {
 					reg = <0>;
-					du_out_rgb: endpoint {
-					};
 				};
 				port@1 {
 					reg = <1>;
@@ -2616,8 +2619,6 @@
 				};
 				port@1 {
 					reg = <1>;
-					lvds0_out: endpoint {
-					};
 				};
 			};
 		};
@@ -2629,7 +2630,7 @@
 	};
 
 	thermal-zones {
-		sensor_thermal1: sensor-thermal1 {
+		sensor1_thermal: sensor1-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 			thermal-sensors = <&tsc 0>;
@@ -2644,7 +2645,7 @@
 			};
 		};
 
-		sensor_thermal2: sensor-thermal2 {
+		sensor2_thermal: sensor2-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 			thermal-sensors = <&tsc 1>;
@@ -2659,7 +2660,7 @@
 			};
 		};
 
-		sensor_thermal3: sensor-thermal3 {
+		sensor3_thermal: sensor3-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 			thermal-sensors = <&tsc 2>;
diff --git a/arch/arm64/boot/dts/renesas/r8a774c0-cat874.dts b/arch/arm64/boot/dts/renesas/r8a774c0-cat874.dts
index 4e72e4f2bab0..5a6ea08ffd2b 100644
--- a/arch/arm64/boot/dts/renesas/r8a774c0-cat874.dts
+++ b/arch/arm64/boot/dts/renesas/r8a774c0-cat874.dts
@@ -172,7 +172,7 @@
 
 	ports {
 		port@0 {
-			endpoint {
+			du_out_rgb: endpoint {
 				remote-endpoint = <&tda19988_in>;
 			};
 		};
diff --git a/arch/arm64/boot/dts/renesas/r8a774c0-ek874-idk-2121wr.dts b/arch/arm64/boot/dts/renesas/r8a774c0-ek874-idk-2121wr.dts
index a7b27d09f6c2..c1812d1ef06a 100644
--- a/arch/arm64/boot/dts/renesas/r8a774c0-ek874-idk-2121wr.dts
+++ b/arch/arm64/boot/dts/renesas/r8a774c0-ek874-idk-2121wr.dts
@@ -68,7 +68,7 @@
 	 * When GP0_17 is low LVDS[01] are connected to the LVDS connector
 	 * When GP0_17 is high LVDS[01] are connected to the LT8918L
 	 */
-	lvds-connector-en-gpio{
+	lvds-connector-en-hog {
 		gpio-hog;
 		gpios = <17 GPIO_ACTIVE_HIGH>;
 		output-low;
diff --git a/arch/arm64/boot/dts/renesas/r8a774c0.dtsi b/arch/arm64/boot/dts/renesas/r8a774c0.dtsi
index d597772c4c37..151e32ac0368 100644
--- a/arch/arm64/boot/dts/renesas/r8a774c0.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a774c0.dtsi
@@ -44,7 +44,7 @@
 		clock-frequency = <0>;
 	};
 
-	cluster1_opp: opp_table10 {
+	cluster1_opp: opp-table-1 {
 		compatible = "operating-points-v2";
 		opp-shared;
 		opp-800000000 {
@@ -145,6 +145,7 @@
 			compatible = "renesas,r8a774c0-wdt",
 				     "renesas,rcar-gen3-wdt";
 			reg = <0 0xe6020000 0 0x0c>;
+			interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 402>;
 			power-domains = <&sysc R8A774C0_PD_ALWAYS_ON>;
 			resets = <&cpg 402>;
@@ -1008,6 +1009,7 @@
 			reg = <0 0xe66c0000 0 0x8000>;
 			interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "ch_int", "g_int";
 			clocks = <&cpg CPG_MOD 914>,
 				 <&cpg CPG_CORE R8A774C0_CLK_CANFD>,
 				 <&can_clk>;
@@ -1279,7 +1281,7 @@
 
 					vin4csi40: endpoint@2 {
 						reg = <2>;
-						remote-endpoint= <&csi40vin4>;
+						remote-endpoint = <&csi40vin4>;
 					};
 				};
 			};
@@ -1307,7 +1309,7 @@
 
 					vin5csi40: endpoint@2 {
 						reg = <2>;
-						remote-endpoint= <&csi40vin5>;
+						remote-endpoint = <&csi40vin5>;
 					};
 				};
 			};
@@ -1328,11 +1330,11 @@
 			 */
 			compatible = "renesas,rcar_sound-r8a774c0",
 				     "renesas,rcar_sound-gen3";
-			reg =	<0 0xec500000 0 0x1000>, /* SCU */
-				<0 0xec5a0000 0 0x100>,  /* ADG */
-				<0 0xec540000 0 0x1000>, /* SSIU */
-				<0 0xec541000 0 0x280>,  /* SSI */
-				<0 0xec760000 0 0x200>;  /* Audio DMAC peri peri*/
+			reg = <0 0xec500000 0 0x1000>, /* SCU */
+			      <0 0xec5a0000 0 0x100>,  /* ADG */
+			      <0 0xec540000 0 0x1000>, /* SSIU */
+			      <0 0xec541000 0 0x280>,  /* SSI */
+			      <0 0xec760000 0 0x200>;  /* Audio DMAC peri peri*/
 			reg-names = "scu", "adg", "ssiu", "ssi", "audmapp";
 
 			clocks = <&cpg CPG_MOD 1005>,
@@ -1626,7 +1628,8 @@
 				     "renesas,rcar-gen3-sdhi";
 			reg = <0 0xee100000 0 0x2000>;
 			interrupts = <GIC_SPI 165 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&cpg CPG_MOD 314>;
+			clocks = <&cpg CPG_MOD 314>, <&cpg CPG_CORE R8A774C0_CLK_SD0H>;
+			clock-names = "core", "clkh";
 			max-frequency = <200000000>;
 			power-domains = <&sysc R8A774C0_PD_ALWAYS_ON>;
 			resets = <&cpg 314>;
@@ -1638,7 +1641,8 @@
 				     "renesas,rcar-gen3-sdhi";
 			reg = <0 0xee120000 0 0x2000>;
 			interrupts = <GIC_SPI 166 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&cpg CPG_MOD 313>;
+			clocks = <&cpg CPG_MOD 313>, <&cpg CPG_CORE R8A774C0_CLK_SD1H>;
+			clock-names = "core", "clkh";
 			max-frequency = <200000000>;
 			power-domains = <&sysc R8A774C0_PD_ALWAYS_ON>;
 			resets = <&cpg 313>;
@@ -1650,7 +1654,8 @@
 				     "renesas,rcar-gen3-sdhi";
 			reg = <0 0xee160000 0 0x2000>;
 			interrupts = <GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&cpg CPG_MOD 311>;
+			clocks = <&cpg CPG_MOD 311>, <&cpg CPG_CORE R8A774C0_CLK_SD3H>;
+			clock-names = "core", "clkh";
 			max-frequency = <200000000>;
 			power-domains = <&sysc R8A774C0_PD_ALWAYS_ON>;
 			resets = <&cpg 311>;
@@ -1666,7 +1671,6 @@
 			reg-names = "regs", "dirmap", "wbuf";
 			interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 917>;
-			clock-names = "rpc";
 			power-domains = <&sysc R8A774C0_PD_ALWAYS_ON>;
 			resets = <&cpg 917>;
 			#address-cells = <1>;
@@ -1867,8 +1871,6 @@
 
 				port@0 {
 					reg = <0>;
-					du_out_rgb: endpoint {
-					};
 				};
 
 				port@1 {
@@ -1910,8 +1912,6 @@
 
 				port@1 {
 					reg = <1>;
-					lvds0_out: endpoint {
-					};
 				};
 			};
 		};
@@ -1937,8 +1937,6 @@
 
 				port@1 {
 					reg = <1>;
-					lvds1_out: endpoint {
-					};
 				};
 			};
 		};
@@ -1953,7 +1951,7 @@
 		cpu-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <0>;
-			thermal-sensors = <&thermal 0>;
+			thermal-sensors = <&thermal>;
 			sustainable-power = <717>;
 
 			cooling-maps {
diff --git a/arch/arm64/boot/dts/renesas/r8a774e1-beacon-rzg2h-kit.dts b/arch/arm64/boot/dts/renesas/r8a774e1-beacon-rzg2h-kit.dts
index 7b6649a3ded0..3e9ced3b2d33 100644
--- a/arch/arm64/boot/dts/renesas/r8a774e1-beacon-rzg2h-kit.dts
+++ b/arch/arm64/boot/dts/renesas/r8a774e1-beacon-rzg2h-kit.dts
@@ -11,7 +11,7 @@
 
 / {
 	model = "Beacon Embedded Works RZ/G2H Development Kit";
-	compatible =	"beacon,beacon-rzg2h", "renesas,r8a774e1";
+	compatible = "beacon,beacon-rzg2h", "renesas,r8a774e1";
 
 	aliases {
 		serial0 = &scif2;
diff --git a/arch/arm64/boot/dts/renesas/r8a774e1.dtsi b/arch/arm64/boot/dts/renesas/r8a774e1.dtsi
index 379a1300272b..c5a0e7866b2f 100644
--- a/arch/arm64/boot/dts/renesas/r8a774e1.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a774e1.dtsi
@@ -47,7 +47,7 @@
 		clock-frequency = <0>;
 	};
 
-	cluster0_opp: opp_table0 {
+	cluster0_opp: opp-table-0 {
 		compatible = "operating-points-v2";
 		opp-shared;
 
@@ -69,7 +69,7 @@
 		};
 	};
 
-	cluster1_opp: opp_table1 {
+	cluster1_opp: opp-table-1 {
 		compatible = "operating-points-v2";
 		opp-shared;
 
@@ -769,7 +769,7 @@
 			status = "disabled";
 		};
 
-		i2c_dvfs: i2c@e60b0000 {
+		iic_pmic: i2c@e60b0000 {
 			#address-cells = <1>;
 			#size-cells = <0>;
 			compatible = "renesas,iic-r8a774e1",
@@ -1280,6 +1280,7 @@
 			reg = <0 0xe66c0000 0 0x8000>;
 			interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "ch_int", "g_int";
 			clocks = <&cpg CPG_MOD 914>,
 				 <&cpg CPG_CORE R8A774E1_CLK_CANFD>,
 				 <&can_clk>;
@@ -1784,7 +1785,7 @@
 			 * clkout	: #clock-cells = <0>;	<&rcar_sound>;
 			 * clkout0/1/2/3: #clock-cells = <1>;	<&rcar_sound N>;
 			 */
-			compatible =  "renesas,rcar_sound-r8a774e1", "renesas,rcar_sound-gen3";
+			compatible = "renesas,rcar_sound-r8a774e1", "renesas,rcar_sound-gen3";
 			reg = <0 0xec500000 0 0x1000>, /* SCU */
 			      <0 0xec5a0000 0 0x100>,  /* ADG */
 			      <0 0xec540000 0 0x1000>, /* SSIU */
@@ -2043,7 +2044,7 @@
 					dma-names = "rx", "tx";
 				};
 				ssiu40: ssiu-32 {
-					dmas =	<&audma0 0x71>, <&audma1 0x72>;
+					dmas = <&audma0 0x71>, <&audma1 0x72>;
 					dma-names = "rx", "tx";
 				};
 				ssiu41: ssiu-33 {
@@ -2362,7 +2363,8 @@
 				     "renesas,rcar-gen3-sdhi";
 			reg = <0 0xee100000 0 0x2000>;
 			interrupts = <GIC_SPI 165 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&cpg CPG_MOD 314>;
+			clocks = <&cpg CPG_MOD 314>, <&cpg CPG_CORE R8A774E1_CLK_SD0H>;
+			clock-names = "core", "clkh";
 			max-frequency = <200000000>;
 			power-domains = <&sysc R8A774E1_PD_ALWAYS_ON>;
 			resets = <&cpg 314>;
@@ -2375,7 +2377,8 @@
 				     "renesas,rcar-gen3-sdhi";
 			reg = <0 0xee120000 0 0x2000>;
 			interrupts = <GIC_SPI 166 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&cpg CPG_MOD 313>;
+			clocks = <&cpg CPG_MOD 313>, <&cpg CPG_CORE R8A774E1_CLK_SD1H>;
+			clock-names = "core", "clkh";
 			max-frequency = <200000000>;
 			power-domains = <&sysc R8A774E1_PD_ALWAYS_ON>;
 			resets = <&cpg 313>;
@@ -2388,7 +2391,8 @@
 				     "renesas,rcar-gen3-sdhi";
 			reg = <0 0xee140000 0 0x2000>;
 			interrupts = <GIC_SPI 167 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&cpg CPG_MOD 312>;
+			clocks = <&cpg CPG_MOD 312>, <&cpg CPG_CORE R8A774E1_CLK_SD2H>;
+			clock-names = "core", "clkh";
 			max-frequency = <200000000>;
 			power-domains = <&sysc R8A774E1_PD_ALWAYS_ON>;
 			resets = <&cpg 312>;
@@ -2401,7 +2405,8 @@
 				     "renesas,rcar-gen3-sdhi";
 			reg = <0 0xee160000 0 0x2000>;
 			interrupts = <GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&cpg CPG_MOD 311>;
+			clocks = <&cpg CPG_MOD 311>, <&cpg CPG_CORE R8A774E1_CLK_SD3H>;
+			clock-names = "core", "clkh";
 			max-frequency = <200000000>;
 			power-domains = <&sysc R8A774E1_PD_ALWAYS_ON>;
 			resets = <&cpg 311>;
@@ -2418,7 +2423,6 @@
 			reg-names = "regs", "dirmap", "wbuf";
 			interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 917>;
-			clock-names = "rpc";
 			power-domains = <&sysc R8A774E1_PD_ALWAYS_ON>;
 			resets = <&cpg 917>;
 			#address-cells = <1>;
@@ -2853,8 +2857,6 @@
 
 				port@0 {
 					reg = <0>;
-					du_out_rgb: endpoint {
-					};
 				};
 				port@1 {
 					reg = <1>;
@@ -2891,8 +2893,6 @@
 				};
 				port@1 {
 					reg = <1>;
-					lvds0_out: endpoint {
-					};
 				};
 			};
 		};
@@ -2904,7 +2904,7 @@
 	};
 
 	thermal-zones {
-		sensor_thermal1: sensor-thermal1 {
+		sensor1_thermal: sensor1-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 			thermal-sensors = <&tsc 0>;
@@ -2919,7 +2919,7 @@
 			};
 		};
 
-		sensor_thermal2: sensor-thermal2 {
+		sensor2_thermal: sensor2-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 			thermal-sensors = <&tsc 1>;
@@ -2934,7 +2934,7 @@
 			};
 		};
 
-		sensor_thermal3: sensor-thermal3 {
+		sensor3_thermal: sensor3-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 			thermal-sensors = <&tsc 2>;
diff --git a/arch/arm64/boot/dts/renesas/r8a77951.dtsi b/arch/arm64/boot/dts/renesas/r8a77951.dtsi
index 1768a3e6bb8d..07c8763c1e77 100644
--- a/arch/arm64/boot/dts/renesas/r8a77951.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a77951.dtsi
@@ -21,17 +21,6 @@
 	#address-cells = <2>;
 	#size-cells = <2>;
 
-	aliases {
-		i2c0 = &i2c0;
-		i2c1 = &i2c1;
-		i2c2 = &i2c2;
-		i2c3 = &i2c3;
-		i2c4 = &i2c4;
-		i2c5 = &i2c5;
-		i2c6 = &i2c6;
-		i2c7 = &i2c_dvfs;
-	};
-
 	/*
 	 * The external audio clocks are configured as 0 Hz fixed frequency
 	 * clocks by default.
@@ -62,7 +51,7 @@
 		clock-frequency = <0>;
 	};
 
-	cluster0_opp: opp_table0 {
+	cluster0_opp: opp-table-0 {
 		compatible = "operating-points-v2";
 		opp-shared;
 
@@ -96,7 +85,7 @@
 		};
 	};
 
-	cluster1_opp: opp_table1 {
+	cluster1_opp: opp-table-1 {
 		compatible = "operating-points-v2";
 		opp-shared;
 
@@ -369,6 +358,7 @@
 		rwdt: watchdog@e6020000 {
 			compatible = "renesas,r8a7795-wdt", "renesas,rcar-gen3-wdt";
 			reg = <0 0xe6020000 0 0x0c>;
+			interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 402>;
 			power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
 			resets = <&cpg 402>;
@@ -1367,6 +1357,7 @@
 			reg = <0 0xe66c0000 0 0x8000>;
 			interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>,
 				   <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "ch_int", "g_int";
 			clocks = <&cpg CPG_MOD 914>,
 			       <&cpg CPG_CORE R8A7795_CLK_CANFD>,
 			       <&can_clk>;
@@ -2018,12 +2009,12 @@
 			 * clkout	: #clock-cells = <0>;	<&rcar_sound>;
 			 * clkout0/1/2/3: #clock-cells = <1>;	<&rcar_sound N>;
 			 */
-			compatible =  "renesas,rcar_sound-r8a7795", "renesas,rcar_sound-gen3";
-			reg =	<0 0xec500000 0 0x1000>, /* SCU */
-				<0 0xec5a0000 0 0x100>,  /* ADG */
-				<0 0xec540000 0 0x1000>, /* SSIU */
-				<0 0xec541000 0 0x280>,  /* SSI */
-				<0 0xec760000 0 0x200>;  /* Audio DMAC peri peri*/
+			compatible = "renesas,rcar_sound-r8a7795", "renesas,rcar_sound-gen3";
+			reg = <0 0xec500000 0 0x1000>, /* SCU */
+			      <0 0xec5a0000 0 0x100>,  /* ADG */
+			      <0 0xec540000 0 0x1000>, /* SSIU */
+			      <0 0xec541000 0 0x280>,  /* SSI */
+			      <0 0xec760000 0 0x200>;  /* Audio DMAC peri peri*/
 			reg-names = "scu", "adg", "ssiu", "ssi", "audmapp";
 
 			clocks = <&cpg CPG_MOD 1005>,
@@ -2277,7 +2268,7 @@
 					dma-names = "rx", "tx";
 				};
 				ssiu40: ssiu-32 {
-					dmas =	<&audma0 0x71>, <&audma1 0x72>;
+					dmas = <&audma0 0x71>, <&audma1 0x72>;
 					dma-names = "rx", "tx";
 				};
 				ssiu41: ssiu-33 {
@@ -2412,6 +2403,18 @@
 			};
 		};
 
+		mlp: mlp@ec520000 {
+			compatible = "renesas,r8a7795-mlp",
+				     "renesas,rcar-gen3-mlp";
+			reg = <0 0xec520000 0 0x800>;
+			interrupts = <GIC_SPI 384 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 385 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 802>;
+			power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
+			resets = <&cpg 802>;
+			status = "disabled";
+		};
+
 		audma0: dma-controller@ec700000 {
 			compatible = "renesas,dmac-r8a7795",
 				     "renesas,rcar-dmac";
@@ -2668,7 +2671,8 @@
 				     "renesas,rcar-gen3-sdhi";
 			reg = <0 0xee100000 0 0x2000>;
 			interrupts = <GIC_SPI 165 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&cpg CPG_MOD 314>;
+			clocks = <&cpg CPG_MOD 314>, <&cpg CPG_CORE R8A7795_CLK_SD0H>;
+			clock-names = "core", "clkh";
 			max-frequency = <200000000>;
 			power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
 			resets = <&cpg 314>;
@@ -2681,7 +2685,8 @@
 				     "renesas,rcar-gen3-sdhi";
 			reg = <0 0xee120000 0 0x2000>;
 			interrupts = <GIC_SPI 166 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&cpg CPG_MOD 313>;
+			clocks = <&cpg CPG_MOD 313>, <&cpg CPG_CORE R8A7795_CLK_SD1H>;
+			clock-names = "core", "clkh";
 			max-frequency = <200000000>;
 			power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
 			resets = <&cpg 313>;
@@ -2694,7 +2699,8 @@
 				     "renesas,rcar-gen3-sdhi";
 			reg = <0 0xee140000 0 0x2000>;
 			interrupts = <GIC_SPI 167 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&cpg CPG_MOD 312>;
+			clocks = <&cpg CPG_MOD 312>, <&cpg CPG_CORE R8A7795_CLK_SD2H>;
+			clock-names = "core", "clkh";
 			max-frequency = <200000000>;
 			power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
 			resets = <&cpg 312>;
@@ -2707,7 +2713,8 @@
 				     "renesas,rcar-gen3-sdhi";
 			reg = <0 0xee160000 0 0x2000>;
 			interrupts = <GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&cpg CPG_MOD 311>;
+			clocks = <&cpg CPG_MOD 311>, <&cpg CPG_CORE R8A7795_CLK_SD3H>;
+			clock-names = "core", "clkh";
 			max-frequency = <200000000>;
 			power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
 			resets = <&cpg 311>;
@@ -2715,6 +2722,22 @@
 			status = "disabled";
 		};
 
+		rpc: spi@ee200000 {
+			compatible = "renesas,r8a7795-rpc-if",
+				     "renesas,rcar-gen3-rpc-if";
+			reg = <0 0xee200000 0 0x200>,
+			      <0 0x08000000 0 0x04000000>,
+			      <0 0xee208000 0 0x100>;
+			reg-names = "regs", "dirmap", "wbuf";
+			interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 917>;
+			power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
+			resets = <&cpg 917>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
 		sata: sata@ee300000 {
 			compatible = "renesas,sata-r8a7795",
 				     "renesas,rcar-gen3-sata";
@@ -3318,8 +3341,6 @@
 
 				port@0 {
 					reg = <0>;
-					du_out_rgb: endpoint {
-					};
 				};
 				port@1 {
 					reg = <1>;
@@ -3362,8 +3383,6 @@
 				};
 				port@1 {
 					reg = <1>;
-					lvds0_out: endpoint {
-					};
 				};
 			};
 		};
@@ -3375,7 +3394,7 @@
 	};
 
 	thermal-zones {
-		sensor_thermal1: sensor-thermal1 {
+		sensor1_thermal: sensor1-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 			thermal-sensors = <&tsc 0>;
@@ -3390,7 +3409,7 @@
 			};
 		};
 
-		sensor_thermal2: sensor-thermal2 {
+		sensor2_thermal: sensor2-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 			thermal-sensors = <&tsc 1>;
@@ -3405,7 +3424,7 @@
 			};
 		};
 
-		sensor_thermal3: sensor-thermal3 {
+		sensor3_thermal: sensor3-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 			thermal-sensors = <&tsc 2>;
diff --git a/arch/arm64/boot/dts/renesas/r8a77960.dtsi b/arch/arm64/boot/dts/renesas/r8a77960.dtsi
index 2bd8169735d3..1424d4ad941f 100644
--- a/arch/arm64/boot/dts/renesas/r8a77960.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a77960.dtsi
@@ -16,17 +16,6 @@
 	#address-cells = <2>;
 	#size-cells = <2>;
 
-	aliases {
-		i2c0 = &i2c0;
-		i2c1 = &i2c1;
-		i2c2 = &i2c2;
-		i2c3 = &i2c3;
-		i2c4 = &i2c4;
-		i2c5 = &i2c5;
-		i2c6 = &i2c6;
-		i2c7 = &i2c_dvfs;
-	};
-
 	/*
 	 * The external audio clocks are configured as 0 Hz fixed frequency
 	 * clocks by default.
@@ -57,7 +46,7 @@
 		clock-frequency = <0>;
 	};
 
-	cluster0_opp: opp_table0 {
+	cluster0_opp: opp-table-0 {
 		compatible = "operating-points-v2";
 		opp-shared;
 
@@ -97,7 +86,7 @@
 		};
 	};
 
-	cluster1_opp: opp_table1 {
+	cluster1_opp: opp-table-1 {
 		compatible = "operating-points-v2";
 		opp-shared;
 
@@ -334,6 +323,7 @@
 			compatible = "renesas,r8a7796-wdt",
 				     "renesas,rcar-gen3-wdt";
 			reg = <0 0xe6020000 0 0x0c>;
+			interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 402>;
 			power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
 			resets = <&cpg 402>;
@@ -1239,6 +1229,7 @@
 			reg = <0 0xe66c0000 0 0x8000>;
 			interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>,
 				   <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "ch_int", "g_int";
 			clocks = <&cpg CPG_MOD 914>,
 			       <&cpg CPG_CORE R8A7796_CLK_CANFD>,
 			       <&can_clk>;
@@ -1890,12 +1881,12 @@
 			 * clkout	: #clock-cells = <0>;	<&rcar_sound>;
 			 * clkout0/1/2/3: #clock-cells = <1>;	<&rcar_sound N>;
 			 */
-			compatible =  "renesas,rcar_sound-r8a7796", "renesas,rcar_sound-gen3";
-			reg =	<0 0xec500000 0 0x1000>, /* SCU */
-				<0 0xec5a0000 0 0x100>,  /* ADG */
-				<0 0xec540000 0 0x1000>, /* SSIU */
-				<0 0xec541000 0 0x280>,  /* SSI */
-				<0 0xec760000 0 0x200>;  /* Audio DMAC peri peri*/
+			compatible = "renesas,rcar_sound-r8a7796", "renesas,rcar_sound-gen3";
+			reg = <0 0xec500000 0 0x1000>, /* SCU */
+			      <0 0xec5a0000 0 0x100>,  /* ADG */
+			      <0 0xec540000 0 0x1000>, /* SSIU */
+			      <0 0xec541000 0 0x280>,  /* SSI */
+			      <0 0xec760000 0 0x200>;  /* Audio DMAC peri peri*/
 			reg-names = "scu", "adg", "ssiu", "ssi", "audmapp";
 
 			clocks = <&cpg CPG_MOD 1005>,
@@ -2202,7 +2193,7 @@
 					dma-names = "rx", "tx";
 				};
 				ssiu40: ssiu-32 {
-					dmas =	<&audma0 0x71>, <&audma1 0x72>;
+					dmas = <&audma0 0x71>, <&audma1 0x72>;
 					dma-names = "rx", "tx";
 				};
 				ssiu41: ssiu-33 {
@@ -2284,6 +2275,18 @@
 			};
 		};
 
+		mlp: mlp@ec520000 {
+			compatible = "renesas,r8a7796-mlp",
+				     "renesas,rcar-gen3-mlp";
+			reg = <0 0xec520000 0 0x800>;
+			interrupts = <GIC_SPI 384 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 385 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 802>;
+			power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
+			resets = <&cpg 802>;
+			status = "disabled";
+		};
+
 		audma0: dma-controller@ec700000 {
 			compatible = "renesas,dmac-r8a7796",
 				     "renesas,rcar-dmac";
@@ -2468,7 +2471,8 @@
 				     "renesas,rcar-gen3-sdhi";
 			reg = <0 0xee100000 0 0x2000>;
 			interrupts = <GIC_SPI 165 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&cpg CPG_MOD 314>;
+			clocks = <&cpg CPG_MOD 314>, <&cpg CPG_CORE R8A7796_CLK_SD0H>;
+			clock-names = "core", "clkh";
 			max-frequency = <200000000>;
 			power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
 			resets = <&cpg 314>;
@@ -2481,7 +2485,8 @@
 				     "renesas,rcar-gen3-sdhi";
 			reg = <0 0xee120000 0 0x2000>;
 			interrupts = <GIC_SPI 166 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&cpg CPG_MOD 313>;
+			clocks = <&cpg CPG_MOD 313>, <&cpg CPG_CORE R8A7796_CLK_SD1H>;
+			clock-names = "core", "clkh";
 			max-frequency = <200000000>;
 			power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
 			resets = <&cpg 313>;
@@ -2494,7 +2499,8 @@
 				     "renesas,rcar-gen3-sdhi";
 			reg = <0 0xee140000 0 0x2000>;
 			interrupts = <GIC_SPI 167 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&cpg CPG_MOD 312>;
+			clocks = <&cpg CPG_MOD 312>, <&cpg CPG_CORE R8A7796_CLK_SD2H>;
+			clock-names = "core", "clkh";
 			max-frequency = <200000000>;
 			power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
 			resets = <&cpg 312>;
@@ -2507,7 +2513,8 @@
 				     "renesas,rcar-gen3-sdhi";
 			reg = <0 0xee160000 0 0x2000>;
 			interrupts = <GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&cpg CPG_MOD 311>;
+			clocks = <&cpg CPG_MOD 311>, <&cpg CPG_CORE R8A7796_CLK_SD3H>;
+			clock-names = "core", "clkh";
 			max-frequency = <200000000>;
 			power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
 			resets = <&cpg 311>;
@@ -2515,6 +2522,22 @@
 			status = "disabled";
 		};
 
+		rpc: spi@ee200000 {
+			compatible = "renesas,r8a7796-rpc-if",
+				     "renesas,rcar-gen3-rpc-if";
+			reg = <0 0xee200000 0 0x200>,
+			      <0 0x08000000 0 0x04000000>,
+			      <0 0xee208000 0 0x100>;
+			reg-names = "regs", "dirmap", "wbuf";
+			interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 917>;
+			power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
+			resets = <&cpg 917>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
 		gic: interrupt-controller@f1010000 {
 			compatible = "arm,gic-400";
 			#interrupt-cells = <3>;
@@ -2921,8 +2944,6 @@
 
 				port@0 {
 					reg = <0>;
-					du_out_rgb: endpoint {
-					};
 				};
 				port@1 {
 					reg = <1>;
@@ -2959,8 +2980,6 @@
 				};
 				port@1 {
 					reg = <1>;
-					lvds0_out: endpoint {
-					};
 				};
 			};
 		};
@@ -2972,7 +2991,7 @@
 	};
 
 	thermal-zones {
-		sensor_thermal1: sensor-thermal1 {
+		sensor1_thermal: sensor1-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 			thermal-sensors = <&tsc 0>;
@@ -2987,7 +3006,7 @@
 			};
 		};
 
-		sensor_thermal2: sensor-thermal2 {
+		sensor2_thermal: sensor2-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 			thermal-sensors = <&tsc 1>;
@@ -3002,7 +3021,7 @@
 			};
 		};
 
-		sensor_thermal3: sensor-thermal3 {
+		sensor3_thermal: sensor3-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 			thermal-sensors = <&tsc 2>;
diff --git a/arch/arm64/boot/dts/renesas/r8a77961.dtsi b/arch/arm64/boot/dts/renesas/r8a77961.dtsi
index 86d59e7e1a87..3c744b7d0dc4 100644
--- a/arch/arm64/boot/dts/renesas/r8a77961.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a77961.dtsi
@@ -46,7 +46,7 @@
 		clock-frequency = <0>;
 	};
 
-	cluster0_opp: opp_table0 {
+	cluster0_opp: opp-table-0 {
 		compatible = "operating-points-v2";
 		opp-shared;
 
@@ -86,7 +86,7 @@
 		};
 	};
 
-	cluster1_opp: opp_table1 {
+	cluster1_opp: opp-table-1 {
 		compatible = "operating-points-v2";
 		opp-shared;
 
@@ -323,6 +323,7 @@
 			compatible = "renesas,r8a77961-wdt",
 				     "renesas,rcar-gen3-wdt";
 			reg = <0 0xe6020000 0 0x0c>;
+			interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 402>;
 			power-domains = <&sysc R8A77961_PD_ALWAYS_ON>;
 			resets = <&cpg 402>;
@@ -1222,6 +1223,32 @@
 			status = "disabled";
 		};
 
+		canfd: can@e66c0000 {
+			compatible = "renesas,r8a77961-canfd",
+				     "renesas,rcar-gen3-canfd";
+			reg = <0 0xe66c0000 0 0x8000>;
+			interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>,
+				   <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "ch_int", "g_int";
+			clocks = <&cpg CPG_MOD 914>,
+			       <&cpg CPG_CORE R8A77961_CLK_CANFD>,
+			       <&can_clk>;
+			clock-names = "fck", "canfd", "can_clk";
+			assigned-clocks = <&cpg CPG_CORE R8A77961_CLK_CANFD>;
+			assigned-clock-rates = <40000000>;
+			power-domains = <&sysc R8A77961_PD_ALWAYS_ON>;
+			resets = <&cpg 914>;
+			status = "disabled";
+
+			channel0 {
+				status = "disabled";
+			};
+
+			channel1 {
+				status = "disabled";
+			};
+		};
+
 		pwm0: pwm@e6e30000 {
 			compatible = "renesas,pwm-r8a77961", "renesas,pwm-rcar";
 			reg = <0 0xe6e30000 0 8>;
@@ -1734,7 +1761,7 @@
 			 * clkout	: #clock-cells = <0>;	<&rcar_sound>;
 			 * clkout0/1/2/3: #clock-cells = <1>;	<&rcar_sound N>;
 			 */
-			compatible =  "renesas,rcar_sound-r8a77961", "renesas,rcar_sound-gen3";
+			compatible = "renesas,rcar_sound-r8a77961", "renesas,rcar_sound-gen3";
 			reg = <0 0xec500000 0 0x1000>, /* SCU */
 			      <0 0xec5a0000 0 0x100>,  /* ADG */
 			      <0 0xec540000 0 0x1000>, /* SSIU */
@@ -2046,7 +2073,7 @@
 					dma-names = "rx", "tx";
 				};
 				ssiu40: ssiu-32 {
-					dmas =	<&audma0 0x71>, <&audma1 0x72>;
+					dmas = <&audma0 0x71>, <&audma1 0x72>;
 					dma-names = "rx", "tx";
 				};
 				ssiu41: ssiu-33 {
@@ -2128,6 +2155,18 @@
 			};
 		};
 
+		mlp: mlp@ec520000 {
+			compatible = "renesas,r8a77961-mlp",
+				     "renesas,rcar-gen3-mlp";
+			reg = <0 0xec520000 0 0x800>;
+			interrupts = <GIC_SPI 384 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 385 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 802>;
+			power-domains = <&sysc R8A77961_PD_ALWAYS_ON>;
+			resets = <&cpg 802>;
+			status = "disabled";
+		};
+
 		audma0: dma-controller@ec700000 {
 			compatible = "renesas,dmac-r8a77961",
 				     "renesas,rcar-dmac";
@@ -2312,7 +2351,8 @@
 				     "renesas,rcar-gen3-sdhi";
 			reg = <0 0xee100000 0 0x2000>;
 			interrupts = <GIC_SPI 165 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&cpg CPG_MOD 314>;
+			clocks = <&cpg CPG_MOD 314>, <&cpg CPG_CORE R8A77961_CLK_SD0H>;
+			clock-names = "core", "clkh";
 			max-frequency = <200000000>;
 			power-domains = <&sysc R8A77961_PD_ALWAYS_ON>;
 			resets = <&cpg 314>;
@@ -2325,7 +2365,8 @@
 				     "renesas,rcar-gen3-sdhi";
 			reg = <0 0xee120000 0 0x2000>;
 			interrupts = <GIC_SPI 166 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&cpg CPG_MOD 313>;
+			clocks = <&cpg CPG_MOD 313>, <&cpg CPG_CORE R8A77961_CLK_SD1H>;
+			clock-names = "core", "clkh";
 			max-frequency = <200000000>;
 			power-domains = <&sysc R8A77961_PD_ALWAYS_ON>;
 			resets = <&cpg 313>;
@@ -2338,7 +2379,8 @@
 				     "renesas,rcar-gen3-sdhi";
 			reg = <0 0xee140000 0 0x2000>;
 			interrupts = <GIC_SPI 167 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&cpg CPG_MOD 312>;
+			clocks = <&cpg CPG_MOD 312>, <&cpg CPG_CORE R8A77961_CLK_SD2H>;
+			clock-names = "core", "clkh";
 			max-frequency = <200000000>;
 			power-domains = <&sysc R8A77961_PD_ALWAYS_ON>;
 			resets = <&cpg 312>;
@@ -2351,7 +2393,8 @@
 				     "renesas,rcar-gen3-sdhi";
 			reg = <0 0xee160000 0 0x2000>;
 			interrupts = <GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&cpg CPG_MOD 311>;
+			clocks = <&cpg CPG_MOD 311>, <&cpg CPG_CORE R8A77961_CLK_SD3H>;
+			clock-names = "core", "clkh";
 			max-frequency = <200000000>;
 			power-domains = <&sysc R8A77961_PD_ALWAYS_ON>;
 			resets = <&cpg 311>;
@@ -2359,6 +2402,22 @@
 			status = "disabled";
 		};
 
+		rpc: spi@ee200000 {
+			compatible = "renesas,r8a77961-rpc-if",
+				     "renesas,rcar-gen3-rpc-if";
+			reg = <0 0xee200000 0 0x200>,
+			      <0 0x08000000 0 0x04000000>,
+			      <0 0xee208000 0 0x100>;
+			reg-names = "regs", "dirmap", "wbuf";
+			interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 917>;
+			power-domains = <&sysc R8A77961_PD_ALWAYS_ON>;
+			resets = <&cpg 917>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
 		gic: interrupt-controller@f1010000 {
 			compatible = "arm,gic-400";
 			#interrupt-cells = <3>;
@@ -2706,8 +2765,6 @@
 
 				port@0 {
 					reg = <0>;
-					du_out_rgb: endpoint {
-					};
 				};
 				port@1 {
 					reg = <1>;
@@ -2718,8 +2775,33 @@
 				port@2 {
 					reg = <2>;
 					du_out_lvds0: endpoint {
+						remote-endpoint = <&lvds0_in>;
+					};
+				};
+			};
+		};
+
+		lvds0: lvds@feb90000 {
+			compatible = "renesas,r8a77961-lvds";
+			reg = <0 0xfeb90000 0 0x14>;
+			clocks = <&cpg CPG_MOD 727>;
+			power-domains = <&sysc R8A77961_PD_ALWAYS_ON>;
+			resets = <&cpg 727>;
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+					lvds0_in: endpoint {
+						remote-endpoint = <&du_out_lvds0>;
 					};
 				};
+				port@1 {
+					reg = <1>;
+				};
 			};
 		};
 
@@ -2730,7 +2812,7 @@
 	};
 
 	thermal-zones {
-		sensor_thermal1: sensor-thermal1 {
+		sensor1_thermal: sensor1-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 			thermal-sensors = <&tsc 0>;
@@ -2745,7 +2827,7 @@
 			};
 		};
 
-		sensor_thermal2: sensor-thermal2 {
+		sensor2_thermal: sensor2-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 			thermal-sensors = <&tsc 1>;
@@ -2760,7 +2842,7 @@
 			};
 		};
 
-		sensor_thermal3: sensor-thermal3 {
+		sensor3_thermal: sensor3-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 			thermal-sensors = <&tsc 2>;
diff --git a/arch/arm64/boot/dts/renesas/r8a77965.dtsi b/arch/arm64/boot/dts/renesas/r8a77965.dtsi
index 08df75606430..997f29521f66 100644
--- a/arch/arm64/boot/dts/renesas/r8a77965.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a77965.dtsi
@@ -21,17 +21,6 @@
 	#address-cells = <2>;
 	#size-cells = <2>;
 
-	aliases {
-		i2c0 = &i2c0;
-		i2c1 = &i2c1;
-		i2c2 = &i2c2;
-		i2c3 = &i2c3;
-		i2c4 = &i2c4;
-		i2c5 = &i2c5;
-		i2c6 = &i2c6;
-		i2c7 = &i2c_dvfs;
-	};
-
 	/*
 	 * The external audio clocks are configured as 0 Hz fixed frequency
 	 * clocks by default.
@@ -62,7 +51,7 @@
 		clock-frequency = <0>;
 	};
 
-	cluster0_opp: opp_table0 {
+	cluster0_opp: opp-table-0 {
 		compatible = "operating-points-v2";
 		opp-shared;
 
@@ -205,6 +194,7 @@
 			compatible = "renesas,r8a77965-wdt",
 				     "renesas,rcar-gen3-wdt";
 			reg = <0 0xe6020000 0 0x0c>;
+			interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 402>;
 			power-domains = <&sysc R8A77965_PD_ALWAYS_ON>;
 			resets = <&cpg 402>;
@@ -1102,6 +1092,7 @@
 			reg = <0 0xe66c0000 0 0x8000>;
 			interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>,
 				   <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "ch_int", "g_int";
 			clocks = <&cpg CPG_MOD 914>,
 			       <&cpg CPG_CORE R8A77965_CLK_CANFD>,
 			       <&can_clk>;
@@ -1753,12 +1744,12 @@
 			 * clkout	: #clock-cells = <0>;	<&rcar_sound>;
 			 * clkout0/1/2/3: #clock-cells = <1>;	<&rcar_sound N>;
 			 */
-			compatible =  "renesas,rcar_sound-r8a77965", "renesas,rcar_sound-gen3";
-			reg =	<0 0xec500000 0 0x1000>, /* SCU */
-				<0 0xec5a0000 0 0x100>,  /* ADG */
-				<0 0xec540000 0 0x1000>, /* SSIU */
-				<0 0xec541000 0 0x280>,  /* SSI */
-				<0 0xec760000 0 0x200>;  /* Audio DMAC peri peri*/
+			compatible = "renesas,rcar_sound-r8a77965", "renesas,rcar_sound-gen3";
+			reg = <0 0xec500000 0 0x1000>, /* SCU */
+			      <0 0xec5a0000 0 0x100>,  /* ADG */
+			      <0 0xec540000 0 0x1000>, /* SSIU */
+			      <0 0xec541000 0 0x280>,  /* SSI */
+			      <0 0xec760000 0 0x200>;  /* Audio DMAC peri peri*/
 			reg-names = "scu", "adg", "ssiu", "ssi", "audmapp";
 
 			clocks = <&cpg CPG_MOD 1005>,
@@ -2012,7 +2003,7 @@
 					dma-names = "rx", "tx";
 				};
 				ssiu40: ssiu-32 {
-					dmas =	<&audma0 0x71>, <&audma1 0x72>;
+					dmas = <&audma0 0x71>, <&audma1 0x72>;
 					dma-names = "rx", "tx";
 				};
 				ssiu41: ssiu-33 {
@@ -2147,6 +2138,18 @@
 			};
 		};
 
+		mlp: mlp@ec520000 {
+			compatible = "renesas,r8a77965-mlp",
+				     "renesas,rcar-gen3-mlp";
+			reg = <0 0xec520000 0 0x800>;
+			interrupts = <GIC_SPI 384 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 385 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 802>;
+			power-domains = <&sysc R8A77965_PD_ALWAYS_ON>;
+			resets = <&cpg 802>;
+			status = "disabled";
+		};
+
 		audma0: dma-controller@ec700000 {
 			compatible = "renesas,dmac-r8a77965",
 				     "renesas,rcar-dmac";
@@ -2315,7 +2318,8 @@
 				     "renesas,rcar-gen3-sdhi";
 			reg = <0 0xee100000 0 0x2000>;
 			interrupts = <GIC_SPI 165 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&cpg CPG_MOD 314>;
+			clocks = <&cpg CPG_MOD 314>, <&cpg CPG_CORE R8A77965_CLK_SD0H>;
+			clock-names = "core", "clkh";
 			max-frequency = <200000000>;
 			power-domains = <&sysc R8A77965_PD_ALWAYS_ON>;
 			resets = <&cpg 314>;
@@ -2328,7 +2332,8 @@
 				     "renesas,rcar-gen3-sdhi";
 			reg = <0 0xee120000 0 0x2000>;
 			interrupts = <GIC_SPI 166 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&cpg CPG_MOD 313>;
+			clocks = <&cpg CPG_MOD 313>, <&cpg CPG_CORE R8A77965_CLK_SD1H>;
+			clock-names = "core", "clkh";
 			max-frequency = <200000000>;
 			power-domains = <&sysc R8A77965_PD_ALWAYS_ON>;
 			resets = <&cpg 313>;
@@ -2341,7 +2346,8 @@
 				     "renesas,rcar-gen3-sdhi";
 			reg = <0 0xee140000 0 0x2000>;
 			interrupts = <GIC_SPI 167 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&cpg CPG_MOD 312>;
+			clocks = <&cpg CPG_MOD 312>, <&cpg CPG_CORE R8A77965_CLK_SD2H>;
+			clock-names = "core", "clkh";
 			max-frequency = <200000000>;
 			power-domains = <&sysc R8A77965_PD_ALWAYS_ON>;
 			resets = <&cpg 312>;
@@ -2354,7 +2360,8 @@
 				     "renesas,rcar-gen3-sdhi";
 			reg = <0 0xee160000 0 0x2000>;
 			interrupts = <GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&cpg CPG_MOD 311>;
+			clocks = <&cpg CPG_MOD 311>, <&cpg CPG_CORE R8A77965_CLK_SD3H>;
+			clock-names = "core", "clkh";
 			max-frequency = <200000000>;
 			power-domains = <&sysc R8A77965_PD_ALWAYS_ON>;
 			resets = <&cpg 311>;
@@ -2362,6 +2369,22 @@
 			status = "disabled";
 		};
 
+		rpc: spi@ee200000 {
+			compatible = "renesas,r8a77965-rpc-if",
+				     "renesas,rcar-gen3-rpc-if";
+			reg = <0 0xee200000 0 0x200>,
+			      <0 0x08000000 0 0x04000000>,
+			      <0 0xee208000 0 0x100>;
+			reg-names = "regs", "dirmap", "wbuf";
+			interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 917>;
+			power-domains = <&sysc R8A77965_PD_ALWAYS_ON>;
+			resets = <&cpg 917>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
 		sata: sata@ee300000 {
 			compatible = "renesas,sata-r8a77965",
 				     "renesas,rcar-gen3-sata";
@@ -2733,8 +2756,6 @@
 
 				port@0 {
 					reg = <0>;
-					du_out_rgb: endpoint {
-					};
 				};
 				port@1 {
 					reg = <1>;
@@ -2771,8 +2792,6 @@
 				};
 				port@1 {
 					reg = <1>;
-					lvds0_out: endpoint {
-					};
 				};
 			};
 		};
@@ -2784,7 +2803,7 @@
 	};
 
 	thermal-zones {
-		sensor_thermal1: sensor-thermal1 {
+		sensor1_thermal: sensor1-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 			thermal-sensors = <&tsc 0>;
@@ -2799,7 +2818,7 @@
 			};
 		};
 
-		sensor_thermal2: sensor-thermal2 {
+		sensor2_thermal: sensor2-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 			thermal-sensors = <&tsc 1>;
@@ -2814,7 +2833,7 @@
 			};
 		};
 
-		sensor_thermal3: sensor-thermal3 {
+		sensor3_thermal: sensor3-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 			thermal-sensors = <&tsc 2>;
diff --git a/arch/arm64/boot/dts/renesas/r8a77970-eagle.dts b/arch/arm64/boot/dts/renesas/r8a77970-eagle.dts
index b579d3189a93..004a5eacd460 100644
--- a/arch/arm64/boot/dts/renesas/r8a77970-eagle.dts
+++ b/arch/arm64/boot/dts/renesas/r8a77970-eagle.dts
@@ -15,6 +15,11 @@
 	compatible = "renesas,eagle", "renesas,r8a77970";
 
 	aliases {
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+		i2c2 = &i2c2;
+		i2c3 = &i2c3;
+		i2c4 = &i2c4;
 		serial0 = &scif0;
 		ethernet0 = &avb;
 	};
@@ -113,6 +118,20 @@
 	};
 };
 
+&csi40 {
+	status = "okay";
+
+	ports {
+		port@0 {
+			csi40_in: endpoint {
+				clock-lanes = <0>;
+				data-lanes = <1 2 3 4>;
+				remote-endpoint = <&max9286_out0>;
+			};
+		};
+	};
+};
+
 &du {
 	clocks = <&cpg CPG_MOD 724>, <&x1_clk>;
 	clock-names = "du.0", "dclkin.0";
@@ -172,6 +191,89 @@
 	};
 };
 
+&i2c3 {
+	pinctrl-0 = <&i2c3_pins>;
+	pinctrl-names = "default";
+
+	status = "okay";
+	clock-frequency = <400000>;
+
+	gmsl0: gmsl-deserializer@48 {
+		compatible = "maxim,max9286";
+		reg = <0x48>;
+
+		maxim,gpio-poc = <0 GPIO_ACTIVE_LOW>;
+		enable-gpios = <&io_expander 0 GPIO_ACTIVE_HIGH>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+			};
+
+			port@1 {
+				reg = <1>;
+			};
+
+			port@2 {
+				reg = <2>;
+			};
+
+			port@3 {
+				reg = <3>;
+			};
+
+			port@4 {
+				reg = <4>;
+				max9286_out0: endpoint {
+					clock-lanes = <0>;
+					data-lanes = <1 2 3 4>;
+					remote-endpoint = <&csi40_in>;
+				};
+			};
+		};
+
+		i2c-mux {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			i2c@0 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0>;
+
+				status = "disabled";
+			};
+
+			i2c@1 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <1>;
+
+				status = "disabled";
+			};
+
+			i2c@2 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <2>;
+
+				status = "disabled";
+			};
+
+			i2c@3 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <3>;
+
+				status = "disabled";
+			};
+		};
+	};
+};
+
 &lvds0 {
 	status = "okay";
 
@@ -200,6 +302,11 @@
 		function = "i2c0";
 	};
 
+	i2c3_pins: i2c3 {
+		groups = "i2c3_a";
+		function = "i2c3";
+	};
+
 	qspi0_pins: qspi0 {
 		groups = "qspi0_ctrl", "qspi0_data4";
 		function = "qspi0";
diff --git a/arch/arm64/boot/dts/renesas/r8a77970-v3msk.dts b/arch/arm64/boot/dts/renesas/r8a77970-v3msk.dts
index 39f3e6cbba3d..c2b65f8de547 100644
--- a/arch/arm64/boot/dts/renesas/r8a77970-v3msk.dts
+++ b/arch/arm64/boot/dts/renesas/r8a77970-v3msk.dts
@@ -15,6 +15,11 @@
 	compatible = "renesas,v3msk", "renesas,r8a77970";
 
 	aliases {
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+		i2c2 = &i2c2;
+		i2c3 = &i2c3;
+		i2c4 = &i2c4;
 		serial0 = &scif0;
 	};
 
diff --git a/arch/arm64/boot/dts/renesas/r8a77970.dtsi b/arch/arm64/boot/dts/renesas/r8a77970.dtsi
index 517892cf6294..ed6e2e47c604 100644
--- a/arch/arm64/boot/dts/renesas/r8a77970.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a77970.dtsi
@@ -16,14 +16,6 @@
 	#address-cells = <2>;
 	#size-cells = <2>;
 
-	aliases {
-		i2c0 = &i2c0;
-		i2c1 = &i2c1;
-		i2c2 = &i2c2;
-		i2c3 = &i2c3;
-		i2c4 = &i2c4;
-	};
-
 	/* External CAN clock - to be overridden by boards that provide it */
 	can_clk: can {
 		compatible = "fixed-clock";
@@ -108,6 +100,7 @@
 			compatible = "renesas,r8a77970-wdt",
 				     "renesas,rcar-gen3-wdt";
 			reg = <0 0xe6020000 0 0x0c>;
+			interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 402>;
 			power-domains = <&sysc R8A77970_PD_ALWAYS_ON>;
 			resets = <&cpg 402>;
@@ -556,6 +549,7 @@
 			reg = <0 0xe66c0000 0 0x8000>;
 			interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "ch_int", "g_int";
 			clocks = <&cpg CPG_MOD 914>,
 				 <&cpg CPG_CORE R8A77970_CLK_CANFD>,
 				 <&can_clk>;
@@ -1051,7 +1045,6 @@
 			reg-names = "regs", "dirmap", "wbuf";
 			interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 917>;
-			clock-names = "rpc";
 			power-domains = <&sysc R8A77970_PD_ALWAYS_ON>;
 			resets = <&cpg 917>;
 			#address-cells = <1>;
@@ -1156,8 +1149,6 @@
 
 				port@0 {
 					reg = <0>;
-					du_out_rgb: endpoint {
-					};
 				};
 
 				port@1 {
@@ -1190,8 +1181,6 @@
 				};
 				port@1 {
 					reg = <1>;
-					lvds0_out: endpoint {
-					};
 				};
 			};
 		};
diff --git a/arch/arm64/boot/dts/renesas/r8a77980-condor.dts b/arch/arm64/boot/dts/renesas/r8a77980-condor.dts
index 3d6d10c82f48..1d326552e2fa 100644
--- a/arch/arm64/boot/dts/renesas/r8a77980-condor.dts
+++ b/arch/arm64/boot/dts/renesas/r8a77980-condor.dts
@@ -8,350 +8,9 @@
 
 /dts-v1/;
 #include "r8a77980.dtsi"
-#include <dt-bindings/gpio/gpio.h>
+#include "condor-common.dtsi"
 
 / {
 	model = "Renesas Condor board based on r8a77980";
 	compatible = "renesas,condor", "renesas,r8a77980";
-
-	aliases {
-		serial0 = &scif0;
-		ethernet0 = &gether;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	d1_8v: regulator-2 {
-		compatible = "regulator-fixed";
-		regulator-name = "D1.8V";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <1800000>;
-		regulator-boot-on;
-		regulator-always-on;
-	};
-
-	d3_3v: regulator-0 {
-		compatible = "regulator-fixed";
-		regulator-name = "D3.3V";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		regulator-boot-on;
-		regulator-always-on;
-	};
-
-	hdmi-out {
-		compatible = "hdmi-connector";
-		type = "a";
-
-		port {
-			hdmi_con: endpoint {
-				remote-endpoint = <&adv7511_out>;
-			};
-		};
-	};
-
-	lvds-decoder {
-		compatible = "thine,thc63lvd1024";
-		vcc-supply = <&d3_3v>;
-
-		ports {
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			port@0 {
-				reg = <0>;
-				thc63lvd1024_in: endpoint {
-					remote-endpoint = <&lvds0_out>;
-				};
-			};
-
-			port@2 {
-				reg = <2>;
-				thc63lvd1024_out: endpoint {
-					remote-endpoint = <&adv7511_in>;
-				};
-			};
-		};
-	};
-
-	memory@48000000 {
-		device_type = "memory";
-		/* first 128MB is reserved for secure area. */
-		reg = <0 0x48000000 0 0x78000000>;
-	};
-
-	vddq_vin01: regulator-1 {
-		compatible = "regulator-fixed";
-		regulator-name = "VDDQ_VIN01";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <1800000>;
-		regulator-boot-on;
-		regulator-always-on;
-	};
-
-	x1_clk: x1-clock {
-		compatible = "fixed-clock";
-		#clock-cells = <0>;
-		clock-frequency = <148500000>;
-	};
-};
-
-&canfd {
-	pinctrl-0 = <&canfd0_pins>;
-	pinctrl-names = "default";
-	status = "okay";
-
-	channel0 {
-		status = "okay";
-	};
-};
-
-&du {
-	clocks = <&cpg CPG_MOD 724>,
-		 <&x1_clk>;
-	clock-names = "du.0", "dclkin.0";
-	status = "okay";
-};
-
-&extal_clk {
-	clock-frequency = <16666666>;
-};
-
-&extalr_clk {
-	clock-frequency = <32768>;
-};
-
-&gether {
-	pinctrl-0 = <&gether_pins>;
-	pinctrl-names = "default";
-
-	phy-mode = "rgmii-id";
-	phy-handle = <&phy0>;
-	renesas,no-ether-link;
-	status = "okay";
-
-	phy0: ethernet-phy@0 {
-		compatible = "ethernet-phy-id0022.1622",
-			     "ethernet-phy-ieee802.3-c22";
-		rxc-skew-ps = <1500>;
-		reg = <0>;
-		interrupt-parent = <&gpio4>;
-		interrupts = <23 IRQ_TYPE_LEVEL_LOW>;
-		reset-gpios = <&gpio4 22 GPIO_ACTIVE_LOW>;
-	};
-};
-
-&i2c0 {
-	pinctrl-0 = <&i2c0_pins>;
-	pinctrl-names = "default";
-
-	status = "okay";
-	clock-frequency = <400000>;
-
-	io_expander0: gpio@20 {
-		compatible = "onnn,pca9654";
-		reg = <0x20>;
-		gpio-controller;
-		#gpio-cells = <2>;
-	};
-
-	io_expander1: gpio@21 {
-		compatible = "onnn,pca9654";
-		reg = <0x21>;
-		gpio-controller;
-		#gpio-cells = <2>;
-	};
-
-	hdmi@39 {
-		compatible = "adi,adv7511w";
-		reg = <0x39>;
-		interrupt-parent = <&gpio1>;
-		interrupts = <20 IRQ_TYPE_LEVEL_LOW>;
-		avdd-supply = <&d1_8v>;
-		dvdd-supply = <&d1_8v>;
-		pvdd-supply = <&d1_8v>;
-		bgvdd-supply = <&d1_8v>;
-		dvdd-3v-supply = <&d3_3v>;
-
-		adi,input-depth = <8>;
-		adi,input-colorspace = "rgb";
-		adi,input-clock = "1x";
-
-		ports {
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			port@0 {
-				reg = <0>;
-				adv7511_in: endpoint {
-					remote-endpoint = <&thc63lvd1024_out>;
-				};
-			};
-
-			port@1 {
-				reg = <1>;
-				adv7511_out: endpoint {
-					remote-endpoint = <&hdmi_con>;
-				};
-			};
-		};
-	};
-};
-
-&lvds0 {
-	status = "okay";
-
-	ports {
-		port@1 {
-			lvds0_out: endpoint {
-				remote-endpoint = <&thc63lvd1024_in>;
-			};
-		};
-	};
-};
-
-&mmc0 {
-	pinctrl-0 = <&mmc_pins>;
-	pinctrl-1 = <&mmc_pins>;
-	pinctrl-names = "default", "state_uhs";
-
-	vmmc-supply = <&d3_3v>;
-	vqmmc-supply = <&vddq_vin01>;
-	mmc-hs200-1_8v;
-	bus-width = <8>;
-	no-sd;
-	no-sdio;
-	non-removable;
-	status = "okay";
-};
-
-&pciec {
-	status = "okay";
-};
-
-&pcie_bus_clk {
-	clock-frequency = <100000000>;
-};
-
-&pcie_phy {
-	status = "okay";
-};
-
-&pfc {
-	canfd0_pins: canfd0 {
-		groups = "canfd0_data_a";
-		function = "canfd0";
-	};
-
-	gether_pins: gether {
-		groups = "gether_mdio_a", "gether_rgmii",
-			 "gether_txcrefclk", "gether_txcrefclk_mega";
-		function = "gether";
-	};
-
-	i2c0_pins: i2c0 {
-		groups = "i2c0";
-		function = "i2c0";
-	};
-
-	mmc_pins: mmc {
-		groups = "mmc_data8", "mmc_ctrl", "mmc_ds";
-		function = "mmc";
-		power-source = <1800>;
-	};
-
-	qspi0_pins: qspi0 {
-		groups = "qspi0_ctrl", "qspi0_data4";
-		function = "qspi0";
-	};
-
-	scif0_pins: scif0 {
-		groups = "scif0_data";
-		function = "scif0";
-	};
-
-	scif_clk_pins: scif_clk {
-		groups = "scif_clk_b";
-		function = "scif_clk";
-	};
-};
-
-&rpc {
-	pinctrl-0 = <&qspi0_pins>;
-	pinctrl-names = "default";
-
-	status = "okay";
-
-	flash@0 {
-		compatible = "spansion,s25fs512s", "jedec,spi-nor";
-		reg = <0>;
-		spi-max-frequency = <50000000>;
-		spi-rx-bus-width = <4>;
-
-		partitions {
-			compatible = "fixed-partitions";
-			#address-cells = <1>;
-			#size-cells = <1>;
-
-			bootparam@0 {
-				reg = <0x00000000 0x040000>;
-				read-only;
-			};
-			cr7@40000 {
-				reg = <0x00040000 0x080000>;
-				read-only;
-			};
-			cert_header_sa3@c0000 {
-				reg = <0x000c0000 0x080000>;
-				read-only;
-			};
-			bl2@140000 {
-				reg = <0x00140000 0x040000>;
-				read-only;
-			};
-			cert_header_sa6@180000 {
-				reg = <0x00180000 0x040000>;
-				read-only;
-			};
-			bl31@1c0000 {
-				reg = <0x001c0000 0x460000>;
-				read-only;
-			};
-			uboot@640000 {
-				reg = <0x00640000 0x0c0000>;
-				read-only;
-			};
-			uboot-env@700000 {
-				reg = <0x00700000 0x040000>;
-				read-only;
-			};
-			dtb@740000 {
-				reg = <0x00740000 0x080000>;
-			};
-			kernel@7c0000 {
-				reg = <0x007c0000 0x1400000>;
-			};
-			user@1bc0000 {
-				reg = <0x01bc0000 0x2440000>;
-			};
-		};
-	};
-};
-
-&rwdt {
-	timeout-sec = <60>;
-	status = "okay";
-};
-
-&scif0 {
-	pinctrl-0 = <&scif0_pins>, <&scif_clk_pins>;
-	pinctrl-names = "default";
-
-	status = "okay";
-};
-
-&scif_clk {
-	clock-frequency = <14745600>;
 };
diff --git a/arch/arm64/boot/dts/renesas/r8a77980-v3hsk.dts b/arch/arm64/boot/dts/renesas/r8a77980-v3hsk.dts
index 1d09d8867651..d168b0e7747d 100644
--- a/arch/arm64/boot/dts/renesas/r8a77980-v3hsk.dts
+++ b/arch/arm64/boot/dts/renesas/r8a77980-v3hsk.dts
@@ -15,6 +15,12 @@
 	compatible = "renesas,v3hsk", "renesas,r8a77980";
 
 	aliases {
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+		i2c2 = &i2c2;
+		i2c3 = &i2c3;
+		i2c4 = &i2c4;
+		i2c5 = &i2c5;
 		serial0 = &scif0;
 		ethernet0 = &gether;
 	};
diff --git a/arch/arm64/boot/dts/renesas/r8a77980.dtsi b/arch/arm64/boot/dts/renesas/r8a77980.dtsi
index 6347d15e66b6..c4ac28a0f716 100644
--- a/arch/arm64/boot/dts/renesas/r8a77980.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a77980.dtsi
@@ -16,15 +16,6 @@
 	#address-cells = <2>;
 	#size-cells = <2>;
 
-	aliases {
-		i2c0 = &i2c0;
-		i2c1 = &i2c1;
-		i2c2 = &i2c2;
-		i2c3 = &i2c3;
-		i2c4 = &i2c4;
-		i2c5 = &i2c5;
-	};
-
 	/* External CAN clock - to be overridden by boards that provide it */
 	can_clk: can {
 		compatible = "fixed-clock";
@@ -138,6 +129,7 @@
 			compatible = "renesas,r8a77980-wdt",
 				     "renesas,rcar-gen3-wdt";
 			reg = <0 0xe6020000 0 0x0c>;
+			interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 402>;
 			power-domains = <&sysc R8A77980_PD_ALWAYS_ON>;
 			resets = <&cpg 402>;
@@ -608,6 +600,7 @@
 			reg = <0 0xe66c0000 0 0x8000>;
 			interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "ch_int", "g_int";
 			clocks = <&cpg CPG_MOD 914>,
 				 <&cpg CPG_CORE R8A77980_CLK_CANFD>,
 				 <&can_clk>;
@@ -1339,7 +1332,8 @@
 				     "renesas,rcar-gen3-sdhi";
 			reg = <0 0xee140000 0 0x2000>;
 			interrupts = <GIC_SPI 165 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&cpg CPG_MOD 314>;
+			clocks = <&cpg CPG_MOD 314>, <&cpg CPG_CORE R8A77980_CLK_SD0H>;
+			clock-names = "core", "clkh";
 			power-domains = <&sysc R8A77980_PD_ALWAYS_ON>;
 			resets = <&cpg 314>;
 			max-frequency = <200000000>;
@@ -1356,7 +1350,6 @@
 			reg-names = "regs", "dirmap", "wbuf";
 			interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 917>;
-			clock-names = "rpc";
 			power-domains = <&sysc R8A77980_PD_ALWAYS_ON>;
 			resets = <&cpg 917>;
 			#address-cells = <1>;
@@ -1532,8 +1525,6 @@
 
 				port@0 {
 					reg = <0>;
-					du_out_rgb: endpoint {
-					};
 				};
 
 				port@1 {
@@ -1567,8 +1558,6 @@
 
 				port@1 {
 					reg = <1>;
-					lvds0_out: endpoint {
-					};
 				};
 			};
 		};
@@ -1580,7 +1569,7 @@
 	};
 
 	thermal-zones {
-		thermal-sensor-1 {
+		sensor1_thermal: sensor1-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 			thermal-sensors = <&tsc 0>;
@@ -1599,7 +1588,7 @@
 			};
 		};
 
-		thermal-sensor-2 {
+		sensor2_thermal: sensor2-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 			thermal-sensors = <&tsc 1>;
diff --git a/arch/arm64/boot/dts/renesas/r8a77980a-condor-i.dts b/arch/arm64/boot/dts/renesas/r8a77980a-condor-i.dts
new file mode 100644
index 000000000000..9f488dea0f34
--- /dev/null
+++ b/arch/arm64/boot/dts/renesas/r8a77980a-condor-i.dts
@@ -0,0 +1,15 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device Tree Source for the Condor-I board on r8a77980A (ES2.0)
+ *
+ * Copyright (C) 2022 Renesas Electronics Corp.
+ */
+
+/dts-v1/;
+#include "r8a77980a.dtsi"
+#include "condor-common.dtsi"
+
+/ {
+	model = "Renesas Condor-I board based on r8a77980A (ES2.0)";
+	compatible = "renesas,condor-i", "renesas,r8a77980a", "renesas,r8a77980";
+};
diff --git a/arch/arm64/boot/dts/renesas/r8a77980a.dtsi b/arch/arm64/boot/dts/renesas/r8a77980a.dtsi
new file mode 100644
index 000000000000..25b2d27b6167
--- /dev/null
+++ b/arch/arm64/boot/dts/renesas/r8a77980a.dtsi
@@ -0,0 +1,11 @@
+// SPDX-License-Identifier: (GPL-2.0 or MIT)
+/*
+ * Device Tree Source for the R-Car V3H2 (R8A77980A) SoC
+ *
+ * Copyright (C) 2022 Renesas Electronics Corp.
+ */
+#include "r8a77980.dtsi"
+
+/ {
+	compatible = "renesas,r8a77980a", "renesas,r8a77980";
+};
diff --git a/arch/arm64/boot/dts/renesas/r8a77990.dtsi b/arch/arm64/boot/dts/renesas/r8a77990.dtsi
index 0ea300a8147d..3053b4b21497 100644
--- a/arch/arm64/boot/dts/renesas/r8a77990.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a77990.dtsi
@@ -14,17 +14,6 @@
 	#address-cells = <2>;
 	#size-cells = <2>;
 
-	aliases {
-		i2c0 = &i2c0;
-		i2c1 = &i2c1;
-		i2c2 = &i2c2;
-		i2c3 = &i2c3;
-		i2c4 = &i2c4;
-		i2c5 = &i2c5;
-		i2c6 = &i2c6;
-		i2c7 = &i2c7;
-	};
-
 	/*
 	 * The external audio clocks are configured as 0 Hz fixed frequency
 	 * clocks by default.
@@ -55,7 +44,7 @@
 		clock-frequency = <0>;
 	};
 
-	cluster1_opp: opp_table10 {
+	cluster1_opp: opp-table-1 {
 		compatible = "operating-points-v2";
 		opp-shared;
 		opp-800000000 {
@@ -171,6 +160,7 @@
 			compatible = "renesas,r8a77990-wdt",
 				     "renesas,rcar-gen3-wdt";
 			reg = <0 0xe6020000 0 0x0c>;
+			interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 402>;
 			power-domains = <&sysc R8A77990_PD_ALWAYS_ON>;
 			resets = <&cpg 402>;
@@ -1051,6 +1041,7 @@
 			reg = <0 0xe66c0000 0 0x8000>;
 			interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>,
 				   <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "ch_int", "g_int";
 			clocks = <&cpg CPG_MOD 914>,
 			       <&cpg CPG_CORE R8A77990_CLK_CANFD>,
 			       <&can_clk>;
@@ -1322,7 +1313,7 @@
 
 					vin4csi40: endpoint@2 {
 						reg = <2>;
-						remote-endpoint= <&csi40vin4>;
+						remote-endpoint = <&csi40vin4>;
 					};
 				};
 			};
@@ -1350,7 +1341,7 @@
 
 					vin5csi40: endpoint@2 {
 						reg = <2>;
-						remote-endpoint= <&csi40vin5>;
+						remote-endpoint = <&csi40vin5>;
 					};
 				};
 			};
@@ -1489,12 +1480,12 @@
 			 * clkout	: #clock-cells = <0>;	<&rcar_sound>;
 			 * clkout0/1/2/3: #clock-cells = <1>;	<&rcar_sound N>;
 			 */
-			compatible =  "renesas,rcar_sound-r8a77990", "renesas,rcar_sound-gen3";
-			reg =	<0 0xec500000 0 0x1000>, /* SCU */
-				<0 0xec5a0000 0 0x100>,  /* ADG */
-				<0 0xec540000 0 0x1000>, /* SSIU */
-				<0 0xec541000 0 0x280>,  /* SSI */
-				<0 0xec760000 0 0x200>;  /* Audio DMAC peri peri*/
+			compatible = "renesas,rcar_sound-r8a77990", "renesas,rcar_sound-gen3";
+			reg = <0 0xec500000 0 0x1000>, /* SCU */
+			      <0 0xec5a0000 0 0x100>,  /* ADG */
+			      <0 0xec540000 0 0x1000>, /* SSIU */
+			      <0 0xec541000 0 0x280>,  /* SSI */
+			      <0 0xec760000 0 0x200>;  /* Audio DMAC peri peri*/
 			reg-names = "scu", "adg", "ssiu", "ssi", "audmapp";
 
 			clocks = <&cpg CPG_MOD 1005>,
@@ -1682,6 +1673,18 @@
 			};
 		};
 
+		mlp: mlp@ec520000 {
+			compatible = "renesas,r8a77990-mlp",
+				     "renesas,rcar-gen3-mlp";
+			reg = <0 0xec520000 0 0x800>;
+			interrupts = <GIC_SPI 384 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 385 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 802>;
+			power-domains = <&sysc R8A77990_PD_ALWAYS_ON>;
+			resets = <&cpg 802>;
+			status = "disabled";
+		};
+
 		audma0: dma-controller@ec700000 {
 			compatible = "renesas,dmac-r8a77990",
 				     "renesas,rcar-dmac";
@@ -1788,7 +1791,8 @@
 				     "renesas,rcar-gen3-sdhi";
 			reg = <0 0xee100000 0 0x2000>;
 			interrupts = <GIC_SPI 165 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&cpg CPG_MOD 314>;
+			clocks = <&cpg CPG_MOD 314>, <&cpg CPG_CORE R8A77990_CLK_SD0H>;
+			clock-names = "core", "clkh";
 			max-frequency = <200000000>;
 			power-domains = <&sysc R8A77990_PD_ALWAYS_ON>;
 			resets = <&cpg 314>;
@@ -1801,7 +1805,8 @@
 				     "renesas,rcar-gen3-sdhi";
 			reg = <0 0xee120000 0 0x2000>;
 			interrupts = <GIC_SPI 166 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&cpg CPG_MOD 313>;
+			clocks = <&cpg CPG_MOD 313>, <&cpg CPG_CORE R8A77990_CLK_SD1H>;
+			clock-names = "core", "clkh";
 			max-frequency = <200000000>;
 			power-domains = <&sysc R8A77990_PD_ALWAYS_ON>;
 			resets = <&cpg 313>;
@@ -1814,7 +1819,8 @@
 				     "renesas,rcar-gen3-sdhi";
 			reg = <0 0xee160000 0 0x2000>;
 			interrupts = <GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&cpg CPG_MOD 311>;
+			clocks = <&cpg CPG_MOD 311>, <&cpg CPG_CORE R8A77990_CLK_SD3H>;
+			clock-names = "core", "clkh";
 			max-frequency = <200000000>;
 			power-domains = <&sysc R8A77990_PD_ALWAYS_ON>;
 			resets = <&cpg 311>;
@@ -1822,6 +1828,22 @@
 			status = "disabled";
 		};
 
+		rpc: spi@ee200000 {
+			compatible = "renesas,r8a77990-rpc-if",
+				     "renesas,rcar-gen3-rpc-if";
+			reg = <0 0xee200000 0 0x200>,
+			      <0 0x08000000 0 0x04000000>,
+			      <0 0xee208000 0 0x100>;
+			reg-names = "regs", "dirmap", "wbuf";
+			interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 917>;
+			power-domains = <&sysc R8A77990_PD_ALWAYS_ON>;
+			resets = <&cpg 917>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
 		gic: interrupt-controller@f1010000 {
 			compatible = "arm,gic-400";
 			#interrupt-cells = <3>;
@@ -2016,8 +2038,6 @@
 
 				port@0 {
 					reg = <0>;
-					du_out_rgb: endpoint {
-					};
 				};
 
 				port@1 {
@@ -2059,8 +2079,6 @@
 
 				port@1 {
 					reg = <1>;
-					lvds0_out: endpoint {
-					};
 				};
 			};
 		};
@@ -2086,8 +2104,6 @@
 
 				port@1 {
 					reg = <1>;
-					lvds1_out: endpoint {
-					};
 				};
 			};
 		};
@@ -2102,7 +2118,7 @@
 		cpu-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <0>;
-			thermal-sensors = <&thermal 0>;
+			thermal-sensors = <&thermal>;
 			sustainable-power = <717>;
 
 			cooling-maps {
diff --git a/arch/arm64/boot/dts/renesas/r8a77995.dtsi b/arch/arm64/boot/dts/renesas/r8a77995.dtsi
index 16ad5fc23a67..f040d03e0a87 100644
--- a/arch/arm64/boot/dts/renesas/r8a77995.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a77995.dtsi
@@ -94,6 +94,7 @@
 			compatible = "renesas,r8a77995-wdt",
 				     "renesas,rcar-gen3-wdt";
 			reg = <0 0xe6020000 0 0x0c>;
+			interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 402>;
 			power-domains = <&sysc R8A77995_PD_ALWAYS_ON>;
 			resets = <&cpg 402>;
@@ -556,6 +557,7 @@
 			reg = <0 0xe66c0000 0 0x8000>;
 			interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>,
 				   <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "ch_int", "g_int";
 			clocks = <&cpg CPG_MOD 914>,
 			       <&cpg CPG_CORE R8A77995_CLK_CANFD>,
 			       <&can_clk>;
@@ -1046,12 +1048,12 @@
 			 * clkout	: #clock-cells = <0>;	<&rcar_sound>;
 			 * clkout0/1/2/3: #clock-cells = <1>;	<&rcar_sound N>;
 			 */
-			compatible =  "renesas,rcar_sound-r8a77995", "renesas,rcar_sound-gen3";
-			reg =	<0 0xec500000 0 0x1000>, /* SCU */
-				<0 0xec5a0000 0 0x100>,  /* ADG */
-				<0 0xec540000 0 0x1000>, /* SSIU */
-				<0 0xec541000 0 0x280>,  /* SSI */
-				<0 0xec740000 0 0x200>;  /* Audio DMAC peri peri*/
+			compatible = "renesas,rcar_sound-r8a77995", "renesas,rcar_sound-gen3";
+			reg = <0 0xec500000 0 0x1000>, /* SCU */
+			      <0 0xec5a0000 0 0x100>,  /* ADG */
+			      <0 0xec540000 0 0x1000>, /* SSIU */
+			      <0 0xec541000 0 0x280>,  /* SSI */
+			      <0 0xec740000 0 0x200>;  /* Audio DMAC peri peri*/
 			reg-names = "scu", "adg", "ssiu", "ssi", "audmapp";
 
 			clocks = <&cpg CPG_MOD 1005>,
@@ -1132,6 +1134,18 @@
 			};
 		};
 
+		mlp: mlp@ec520000 {
+			compatible = "renesas,r8a77995-mlp",
+				     "renesas,rcar-gen3-mlp";
+			reg = <0 0xec520000 0 0x800>;
+			interrupts = <GIC_SPI 384 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 385 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 802>;
+			power-domains = <&sysc R8A77995_PD_ALWAYS_ON>;
+			resets = <&cpg 802>;
+			status = "disabled";
+		};
+
 		audma0: dma-controller@ec700000 {
 			compatible = "renesas,dmac-r8a77995",
 				     "renesas,rcar-dmac";
@@ -1216,7 +1230,8 @@
 				     "renesas,rcar-gen3-sdhi";
 			reg = <0 0xee140000 0 0x2000>;
 			interrupts = <GIC_SPI 167 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&cpg CPG_MOD 312>;
+			clocks = <&cpg CPG_MOD 312>, <&cpg CPG_CORE R8A77995_CLK_SD0H>;
+			clock-names = "core", "clkh";
 			max-frequency = <200000000>;
 			power-domains = <&sysc R8A77995_PD_ALWAYS_ON>;
 			resets = <&cpg 312>;
@@ -1224,6 +1239,22 @@
 			status = "disabled";
 		};
 
+		rpc: spi@ee200000 {
+			compatible = "renesas,r8a77995-rpc-if",
+				     "renesas,rcar-gen3-rpc-if";
+			reg = <0 0xee200000 0 0x200>,
+			      <0 0x08000000 0 0x04000000>,
+			      <0 0xee208000 0 0x100>;
+			reg-names = "regs", "dirmap", "wbuf";
+			interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 917>;
+			power-domains = <&sysc R8A77995_PD_ALWAYS_ON>;
+			resets = <&cpg 917>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
 		gic: interrupt-controller@f1010000 {
 			compatible = "arm,gic-400";
 			#interrupt-cells = <3>;
@@ -1337,8 +1368,6 @@
 
 				port@0 {
 					reg = <0>;
-					du_out_rgb: endpoint {
-					};
 				};
 
 				port@1 {
@@ -1380,8 +1409,6 @@
 
 				port@1 {
 					reg = <1>;
-					lvds0_out: endpoint {
-					};
 				};
 			};
 		};
@@ -1407,8 +1434,6 @@
 
 				port@1 {
 					reg = <1>;
-					lvds1_out: endpoint {
-					};
 				};
 			};
 		};
diff --git a/arch/arm64/boot/dts/renesas/r8a779a0-falcon-cpu.dtsi b/arch/arm64/boot/dts/renesas/r8a779a0-falcon-cpu.dtsi
index cd2f0d60f21a..99b73e21c82c 100644
--- a/arch/arm64/boot/dts/renesas/r8a779a0-falcon-cpu.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a779a0-falcon-cpu.dtsi
@@ -16,6 +16,13 @@
 	compatible = "renesas,falcon-cpu", "renesas,r8a779a0";
 
 	aliases {
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+		i2c2 = &i2c2;
+		i2c3 = &i2c3;
+		i2c4 = &i2c4;
+		i2c5 = &i2c5;
+		i2c6 = &i2c6;
 		serial0 = &scif0;
 	};
 
@@ -98,6 +105,27 @@
 		reg = <0x7 0x00000000 0x0 0x80000000>;
 	};
 
+	mini-dp-con {
+		compatible = "dp-connector";
+		label = "CN5";
+		type = "mini";
+
+		port {
+			mini_dp_con_in: endpoint {
+				remote-endpoint = <&sn65dsi86_out>;
+			};
+		};
+	};
+
+	reg_1p2v: regulator-1p2v {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-1.2V";
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <1200000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
 	reg_1p8v: regulator-1p8v {
 		compatible = "regulator-fixed";
 		regulator-name = "fixed-1.8V";
@@ -115,6 +143,29 @@
 		regulator-boot-on;
 		regulator-always-on;
 	};
+
+	sn65dsi86_refclk: clk-x6 {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <38400000>;
+	};
+};
+
+&dsi0 {
+	status = "okay";
+
+	ports {
+		port@1 {
+			dsi0_out: endpoint {
+				remote-endpoint = <&sn65dsi86_in>;
+				data-lanes = <1 2 3 4>;
+			};
+		};
+	};
+};
+
+&du {
+	status = "okay";
 };
 
 &extal_clk {
@@ -146,6 +197,44 @@
 
 	status = "okay";
 	clock-frequency = <400000>;
+
+	bridge@2c {
+		pinctrl-0 = <&irq0_pins>;
+		pinctrl-names = "default";
+
+		compatible = "ti,sn65dsi86";
+		reg = <0x2c>;
+
+		clocks = <&sn65dsi86_refclk>;
+		clock-names = "refclk";
+
+		interrupt-parent = <&intc_ex>;
+		interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
+
+		vccio-supply = <&reg_1p8v>;
+		vpll-supply = <&reg_1p8v>;
+		vcca-supply = <&reg_1p2v>;
+		vcc-supply = <&reg_1p2v>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				sn65dsi86_in: endpoint {
+					remote-endpoint = <&dsi0_out>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+				sn65dsi86_out: endpoint {
+					remote-endpoint = <&mini_dp_con_in>;
+				};
+			};
+		};
+	};
 };
 
 &i2c6 {
@@ -192,6 +281,11 @@
 		function = "i2c6";
 	};
 
+	irq0_pins: irq0 {
+		groups = "intc_ex_irq0";
+		function = "intc_ex";
+	};
+
 	keys_pins: keys {
 		pins = "GP_6_18", "GP_6_19", "GP_6_20";
 		bias-pull-up;
diff --git a/arch/arm64/boot/dts/renesas/r8a779a0-falcon-csi-dsi.dtsi b/arch/arm64/boot/dts/renesas/r8a779a0-falcon-csi-dsi.dtsi
index f791c76f1bcf..e06b8eda85e1 100644
--- a/arch/arm64/boot/dts/renesas/r8a779a0-falcon-csi-dsi.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a779a0-falcon-csi-dsi.dtsi
@@ -5,6 +5,63 @@
  * Copyright (C) 2021 Glider bv
  */
 
+&csi40 {
+	status = "okay";
+
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+
+			csi40_in: endpoint {
+				clock-lanes = <0>;
+				data-lanes = <1 2 3 4>;
+				remote-endpoint = <&max96712_out0>;
+			};
+		};
+	};
+};
+
+&csi42 {
+	status = "okay";
+
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+
+			csi42_in: endpoint {
+				clock-lanes = <0>;
+				data-lanes = <1 2 3 4>;
+				remote-endpoint = <&max96712_out1>;
+			};
+		};
+	};
+};
+
+&csi43 {
+	status = "okay";
+
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+
+			csi43_in: endpoint {
+				clock-lanes = <0>;
+				data-lanes = <1 2 3 4>;
+				remote-endpoint = <&max96712_out2>;
+			};
+		};
+	};
+};
+
 &i2c0 {
 	pca9654_a: gpio@21 {
 		compatible = "onnn,pca9654";
@@ -34,3 +91,175 @@
 		pagesize = <8>;
 	};
 };
+
+&i2c1 {
+	gmsl0: gmsl-deserializer@49 {
+		compatible = "maxim,max96712";
+		reg = <0x49>;
+		enable-gpios = <&pca9654_a 0 GPIO_ACTIVE_HIGH>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@4 {
+				reg = <4>;
+				max96712_out0: endpoint {
+					clock-lanes = <0>;
+					data-lanes = <1 2 3 4>;
+					remote-endpoint = <&csi40_in>;
+				};
+			};
+		};
+	};
+
+	gmsl1: gmsl-deserializer@4b {
+		compatible = "maxim,max96712";
+		reg = <0x4b>;
+		enable-gpios = <&pca9654_b 0 GPIO_ACTIVE_HIGH>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@4 {
+				reg = <4>;
+				max96712_out1: endpoint {
+					clock-lanes = <0>;
+					data-lanes = <1 2 3 4>;
+					lane-polarities = <0 0 0 0 1>;
+					remote-endpoint = <&csi42_in>;
+				};
+			};
+		};
+	};
+
+	gmsl2: gmsl-deserializer@6b {
+		compatible = "maxim,max96712";
+		reg = <0x6b>;
+		enable-gpios = <&pca9654_c 0 GPIO_ACTIVE_HIGH>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@4 {
+				reg = <4>;
+				max96712_out2: endpoint {
+					clock-lanes = <0>;
+					data-lanes = <1 2 3 4>;
+					lane-polarities = <0 0 0 0 1>;
+					remote-endpoint = <&csi43_in>;
+				};
+			};
+		};
+	};
+};
+
+&isp0 {
+	status = "okay";
+};
+
+&isp2 {
+	status = "okay";
+};
+
+&isp3 {
+	status = "okay";
+};
+
+&vin00 {
+	status = "okay";
+};
+
+&vin01 {
+	status = "okay";
+};
+
+&vin02 {
+	status = "okay";
+};
+
+&vin03 {
+	status = "okay";
+};
+
+&vin04 {
+	status = "okay";
+};
+
+&vin05 {
+	status = "okay";
+};
+
+&vin06 {
+	status = "okay";
+};
+
+&vin07 {
+	status = "okay";
+};
+
+&vin16 {
+	status = "okay";
+};
+
+&vin17 {
+	status = "okay";
+};
+
+&vin18 {
+	status = "okay";
+};
+
+&vin19 {
+	status = "okay";
+};
+
+&vin20 {
+	status = "okay";
+};
+
+&vin21 {
+	status = "okay";
+};
+
+&vin22 {
+	status = "okay";
+};
+
+&vin23 {
+	status = "okay";
+};
+
+&vin24 {
+	status = "okay";
+};
+
+&vin25 {
+	status = "okay";
+};
+
+&vin26 {
+	status = "okay";
+};
+
+&vin27 {
+	status = "okay";
+};
+
+&vin28 {
+	status = "okay";
+};
+
+&vin29 {
+	status = "okay";
+};
+
+&vin30 {
+	status = "okay";
+};
+
+&vin31 {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/renesas/r8a779a0-falcon.dts b/arch/arm64/boot/dts/renesas/r8a779a0-falcon.dts
index e46dc9aa0a43..b2e67b82caf6 100644
--- a/arch/arm64/boot/dts/renesas/r8a779a0-falcon.dts
+++ b/arch/arm64/boot/dts/renesas/r8a779a0-falcon.dts
@@ -37,6 +37,20 @@
 	};
 };
 
+&canfd {
+	pinctrl-0 = <&canfd0_pins>, <&canfd1_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	channel0 {
+		status = "okay";
+	};
+
+	channel1 {
+		status = "okay";
+	};
+};
+
 &i2c0 {
 	eeprom@51 {
 		compatible = "rohm,br24g01", "atmel,24c01";
@@ -65,4 +79,14 @@
 		};
 
 	};
+
+	canfd0_pins: canfd0 {
+		groups = "canfd0_data";
+		function = "canfd0";
+	};
+
+	canfd1_pins: canfd1 {
+		groups = "canfd1_data";
+		function = "canfd1";
+	};
 };
diff --git a/arch/arm64/boot/dts/renesas/r8a779a0.dtsi b/arch/arm64/boot/dts/renesas/r8a779a0.dtsi
index 43bf2cbfbd8f..ed9400f903c9 100644
--- a/arch/arm64/boot/dts/renesas/r8a779a0.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a779a0.dtsi
@@ -14,14 +14,11 @@
 	#address-cells = <2>;
 	#size-cells = <2>;
 
-	aliases {
-		i2c0 = &i2c0;
-		i2c1 = &i2c1;
-		i2c2 = &i2c2;
-		i2c3 = &i2c3;
-		i2c4 = &i2c4;
-		i2c5 = &i2c5;
-		i2c6 = &i2c6;
+	/* External CAN clock - to be overridden by boards that provide it */
+	can_clk: can {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <0>;
 	};
 
 	cpus {
@@ -34,6 +31,7 @@
 			device_type = "cpu";
 			power-domains = <&sysc R8A779A0_PD_A1E0D0C0>;
 			next-level-cache = <&L3_CA76_0>;
+			clocks = <&cpg CPG_CORE R8A779A0_CLK_Z0>;
 		};
 
 		L3_CA76_0: cache-controller-0 {
@@ -79,15 +77,16 @@
 
 		rwdt: watchdog@e6020000 {
 			compatible = "renesas,r8a779a0-wdt",
-				     "renesas,rcar-gen3-wdt";
+				     "renesas,rcar-gen4-wdt";
 			reg = <0 0xe6020000 0 0x0c>;
+			interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 907>;
 			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
 			resets = <&cpg 907>;
 			status = "disabled";
 		};
 
-		pfc: pin-controller@e6050000 {
+		pfc: pinctrl@e6050000 {
 			compatible = "renesas,pfc-r8a779a0";
 			reg = <0 0xe6050000 0 0x16c>, <0 0xe6050800 0 0x16c>,
 			      <0 0xe6058000 0 0x16c>, <0 0xe6058800 0 0x16c>,
@@ -97,12 +96,13 @@
 		};
 
 		gpio0: gpio@e6058180 {
-			compatible = "renesas,gpio-r8a779a0";
+			compatible = "renesas,gpio-r8a779a0",
+				     "renesas,rcar-gen4-gpio";
 			reg = <0 0xe6058180 0 0x54>;
 			interrupts = <GIC_SPI 832 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 916>;
 			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
-			resets =  <&cpg 916>;
+			resets = <&cpg 916>;
 			gpio-controller;
 			#gpio-cells = <2>;
 			gpio-ranges = <&pfc 0 0 28>;
@@ -111,12 +111,13 @@
 		};
 
 		gpio1: gpio@e6050180 {
-			compatible = "renesas,gpio-r8a779a0";
+			compatible = "renesas,gpio-r8a779a0",
+				     "renesas,rcar-gen4-gpio";
 			reg = <0 0xe6050180 0 0x54>;
 			interrupts = <GIC_SPI 836 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 915>;
 			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
-			resets =  <&cpg 915>;
+			resets = <&cpg 915>;
 			gpio-controller;
 			#gpio-cells = <2>;
 			gpio-ranges = <&pfc 0 32 31>;
@@ -125,12 +126,13 @@
 		};
 
 		gpio2: gpio@e6050980 {
-			compatible = "renesas,gpio-r8a779a0";
+			compatible = "renesas,gpio-r8a779a0",
+				     "renesas,rcar-gen4-gpio";
 			reg = <0 0xe6050980 0 0x54>;
 			interrupts = <GIC_SPI 840 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 915>;
 			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
-			resets =  <&cpg 915>;
+			resets = <&cpg 915>;
 			gpio-controller;
 			#gpio-cells = <2>;
 			gpio-ranges = <&pfc 0 64 25>;
@@ -139,12 +141,13 @@
 		};
 
 		gpio3: gpio@e6058980 {
-			compatible = "renesas,gpio-r8a779a0";
+			compatible = "renesas,gpio-r8a779a0",
+				     "renesas,rcar-gen4-gpio";
 			reg = <0 0xe6058980 0 0x54>;
 			interrupts = <GIC_SPI 844 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 916>;
 			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
-			resets =  <&cpg 916>;
+			resets = <&cpg 916>;
 			gpio-controller;
 			#gpio-cells = <2>;
 			gpio-ranges = <&pfc 0 96 17>;
@@ -153,12 +156,13 @@
 		};
 
 		gpio4: gpio@e6060180 {
-			compatible = "renesas,gpio-r8a779a0";
+			compatible = "renesas,gpio-r8a779a0",
+				     "renesas,rcar-gen4-gpio";
 			reg = <0 0xe6060180 0 0x54>;
 			interrupts = <GIC_SPI 848 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 917>;
 			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
-			resets =  <&cpg 917>;
+			resets = <&cpg 917>;
 			gpio-controller;
 			#gpio-cells = <2>;
 			gpio-ranges = <&pfc 0 128 27>;
@@ -167,12 +171,13 @@
 		};
 
 		gpio5: gpio@e6060980 {
-			compatible = "renesas,gpio-r8a779a0";
+			compatible = "renesas,gpio-r8a779a0",
+				     "renesas,rcar-gen4-gpio";
 			reg = <0 0xe6060980 0 0x54>;
 			interrupts = <GIC_SPI 852 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 917>;
 			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
-			resets =  <&cpg 917>;
+			resets = <&cpg 917>;
 			gpio-controller;
 			#gpio-cells = <2>;
 			gpio-ranges = <&pfc 0 160 21>;
@@ -181,12 +186,13 @@
 		};
 
 		gpio6: gpio@e6068180 {
-			compatible = "renesas,gpio-r8a779a0";
+			compatible = "renesas,gpio-r8a779a0",
+				     "renesas,rcar-gen4-gpio";
 			reg = <0 0xe6068180 0 0x54>;
 			interrupts = <GIC_SPI 856 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 918>;
 			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
-			resets =  <&cpg 918>;
+			resets = <&cpg 918>;
 			gpio-controller;
 			#gpio-cells = <2>;
 			gpio-ranges = <&pfc 0 192 21>;
@@ -195,12 +201,13 @@
 		};
 
 		gpio7: gpio@e6068980 {
-			compatible = "renesas,gpio-r8a779a0";
+			compatible = "renesas,gpio-r8a779a0",
+				     "renesas,rcar-gen4-gpio";
 			reg = <0 0xe6068980 0 0x54>;
 			interrupts = <GIC_SPI 860 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 918>;
 			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
-			resets =  <&cpg 918>;
+			resets = <&cpg 918>;
 			gpio-controller;
 			#gpio-cells = <2>;
 			gpio-ranges = <&pfc 0 224 21>;
@@ -209,12 +216,13 @@
 		};
 
 		gpio8: gpio@e6069180 {
-			compatible = "renesas,gpio-r8a779a0";
+			compatible = "renesas,gpio-r8a779a0",
+				     "renesas,rcar-gen4-gpio";
 			reg = <0 0xe6069180 0 0x54>;
 			interrupts = <GIC_SPI 864 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 918>;
 			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
-			resets =  <&cpg 918>;
+			resets = <&cpg 918>;
 			gpio-controller;
 			#gpio-cells = <2>;
 			gpio-ranges = <&pfc 0 256 21>;
@@ -223,12 +231,13 @@
 		};
 
 		gpio9: gpio@e6069980 {
-			compatible = "renesas,gpio-r8a779a0";
+			compatible = "renesas,gpio-r8a779a0",
+				     "renesas,rcar-gen4-gpio";
 			reg = <0 0xe6069980 0 0x54>;
 			interrupts = <GIC_SPI 868 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 918>;
 			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
-			resets =  <&cpg 918>;
+			resets = <&cpg 918>;
 			gpio-controller;
 			#gpio-cells = <2>;
 			gpio-ranges = <&pfc 0 288 21>;
@@ -238,7 +247,7 @@
 
 		cmt0: timer@e60f0000 {
 			compatible = "renesas,r8a779a0-cmt0",
-				     "renesas,rcar-gen3-cmt0";
+				     "renesas,rcar-gen4-cmt0";
 			reg = <0 0xe60f0000 0 0x1004>;
 			interrupts = <GIC_SPI 500 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 501 IRQ_TYPE_LEVEL_HIGH>;
@@ -251,7 +260,7 @@
 
 		cmt1: timer@e6130000 {
 			compatible = "renesas,r8a779a0-cmt1",
-				     "renesas,rcar-gen3-cmt1";
+				     "renesas,rcar-gen4-cmt1";
 			reg = <0 0xe6130000 0 0x1004>;
 			interrupts = <GIC_SPI 448 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 449 IRQ_TYPE_LEVEL_HIGH>,
@@ -270,7 +279,7 @@
 
 		cmt2: timer@e6140000 {
 			compatible = "renesas,r8a779a0-cmt1",
-				     "renesas,rcar-gen3-cmt1";
+				     "renesas,rcar-gen4-cmt1";
 			reg = <0 0xe6140000 0 0x1004>;
 			interrupts = <GIC_SPI 456 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 457 IRQ_TYPE_LEVEL_HIGH>,
@@ -289,7 +298,7 @@
 
 		cmt3: timer@e6148000 {
 			compatible = "renesas,r8a779a0-cmt1",
-				     "renesas,rcar-gen3-cmt1";
+				     "renesas,rcar-gen4-cmt1";
 			reg = <0 0xe6148000 0 0x1004>;
 			interrupts = <GIC_SPI 464 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 465 IRQ_TYPE_LEVEL_HIGH>,
@@ -340,6 +349,21 @@
 			#thermal-sensor-cells = <1>;
 		};
 
+		intc_ex: interrupt-controller@e61c0000 {
+			compatible = "renesas,intc-ex-r8a779a0", "renesas,irqc";
+			#interrupt-cells = <2>;
+			interrupt-controller;
+			reg = <0 0xe61c0000 0 0x200>;
+			interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_CORE R8A779A0_CLK_CP>;
+			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
+		};
+
 		tmu0: timer@e61e0000 {
 			compatible = "renesas,tmu-r8a779a0", "renesas,tmu";
 			reg = <0 0xe61e0000 0 0x30>;
@@ -407,7 +431,7 @@
 
 		i2c0: i2c@e6500000 {
 			compatible = "renesas,i2c-r8a779a0",
-				     "renesas,rcar-gen3-i2c";
+				     "renesas,rcar-gen4-i2c";
 			reg = <0 0xe6500000 0 0x40>;
 			interrupts = <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 518>;
@@ -423,7 +447,7 @@
 
 		i2c1: i2c@e6508000 {
 			compatible = "renesas,i2c-r8a779a0",
-				     "renesas,rcar-gen3-i2c";
+				     "renesas,rcar-gen4-i2c";
 			reg = <0 0xe6508000 0 0x40>;
 			interrupts = <GIC_SPI 239 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 519>;
@@ -439,7 +463,7 @@
 
 		i2c2: i2c@e6510000 {
 			compatible = "renesas,i2c-r8a779a0",
-				     "renesas,rcar-gen3-i2c";
+				     "renesas,rcar-gen4-i2c";
 			reg = <0 0xe6510000 0 0x40>;
 			interrupts = <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 520>;
@@ -455,7 +479,7 @@
 
 		i2c3: i2c@e66d0000 {
 			compatible = "renesas,i2c-r8a779a0",
-				     "renesas,rcar-gen3-i2c";
+				     "renesas,rcar-gen4-i2c";
 			reg = <0 0xe66d0000 0 0x40>;
 			interrupts = <GIC_SPI 241 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 521>;
@@ -471,7 +495,7 @@
 
 		i2c4: i2c@e66d8000 {
 			compatible = "renesas,i2c-r8a779a0",
-				     "renesas,rcar-gen3-i2c";
+				     "renesas,rcar-gen4-i2c";
 			reg = <0 0xe66d8000 0 0x40>;
 			interrupts = <GIC_SPI 242 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 522>;
@@ -487,7 +511,7 @@
 
 		i2c5: i2c@e66e0000 {
 			compatible = "renesas,i2c-r8a779a0",
-				     "renesas,rcar-gen3-i2c";
+				     "renesas,rcar-gen4-i2c";
 			reg = <0 0xe66e0000 0 0x40>;
 			interrupts = <GIC_SPI 243 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 523>;
@@ -503,7 +527,7 @@
 
 		i2c6: i2c@e66e8000 {
 			compatible = "renesas,i2c-r8a779a0",
-				     "renesas,rcar-gen3-i2c";
+				     "renesas,rcar-gen4-i2c";
 			reg = <0 0xe66e8000 0 0x40>;
 			interrupts = <GIC_SPI 244 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 524>;
@@ -519,7 +543,7 @@
 
 		hscif0: serial@e6540000 {
 			compatible = "renesas,hscif-r8a779a0",
-				     "renesas,rcar-gen3-hscif", "renesas,hscif";
+				     "renesas,rcar-gen4-hscif", "renesas,hscif";
 			reg = <0 0xe6540000 0 0x60>;
 			interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 514>,
@@ -535,7 +559,7 @@
 
 		hscif1: serial@e6550000 {
 			compatible = "renesas,hscif-r8a779a0",
-				     "renesas,rcar-gen3-hscif", "renesas,hscif";
+				     "renesas,rcar-gen4-hscif", "renesas,hscif";
 			reg = <0 0xe6550000 0 0x60>;
 			interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 515>,
@@ -551,7 +575,7 @@
 
 		hscif2: serial@e6560000 {
 			compatible = "renesas,hscif-r8a779a0",
-				     "renesas,rcar-gen3-hscif", "renesas,hscif";
+				     "renesas,rcar-gen4-hscif", "renesas,hscif";
 			reg = <0 0xe6560000 0 0x60>;
 			interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 516>,
@@ -567,7 +591,7 @@
 
 		hscif3: serial@e66a0000 {
 			compatible = "renesas,hscif-r8a779a0",
-				     "renesas,rcar-gen3-hscif", "renesas,hscif";
+				     "renesas,rcar-gen4-hscif", "renesas,hscif";
 			reg = <0 0xe66a0000 0 0x60>;
 			interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 517>,
@@ -581,6 +605,55 @@
 			status = "disabled";
 		};
 
+		canfd: can@e6660000 {
+			compatible = "renesas,r8a779a0-canfd";
+			reg = <0 0xe6660000 0 0x8000>;
+			interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>,
+					<GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "ch_int", "g_int";
+			clocks = <&cpg CPG_MOD 328>,
+				 <&cpg CPG_CORE R8A779A0_CLK_CANFD>,
+				 <&can_clk>;
+			clock-names = "fck", "canfd", "can_clk";
+			assigned-clocks = <&cpg CPG_CORE R8A779A0_CLK_CANFD>;
+			assigned-clock-rates = <80000000>;
+			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
+			resets = <&cpg 328>;
+			status = "disabled";
+
+			channel0 {
+				status = "disabled";
+			};
+
+			channel1 {
+				status = "disabled";
+			};
+
+			channel2 {
+				status = "disabled";
+			};
+
+			channel3 {
+				status = "disabled";
+			};
+
+			channel4 {
+				status = "disabled";
+			};
+
+			channel5 {
+				status = "disabled";
+			};
+
+			channel6 {
+				status = "disabled";
+			};
+
+			channel7 {
+				status = "disabled";
+			};
+		};
+
 		avb0: ethernet@e6800000 {
 			compatible = "renesas,etheravb-r8a779a0",
 				     "renesas,etheravb-rcar-gen3";
@@ -871,7 +944,7 @@
 
 		scif0: serial@e6e60000 {
 			compatible = "renesas,scif-r8a779a0",
-				     "renesas,rcar-gen3-scif", "renesas,scif";
+				     "renesas,rcar-gen4-scif", "renesas,scif";
 			reg = <0 0xe6e60000 0 64>;
 			interrupts = <GIC_SPI 251 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 702>,
@@ -887,7 +960,7 @@
 
 		scif1: serial@e6e68000 {
 			compatible = "renesas,scif-r8a779a0",
-				     "renesas,rcar-gen3-scif", "renesas,scif";
+				     "renesas,rcar-gen4-scif", "renesas,scif";
 			reg = <0 0xe6e68000 0 64>;
 			interrupts = <GIC_SPI 252 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 703>,
@@ -903,7 +976,7 @@
 
 		scif3: serial@e6c50000 {
 			compatible = "renesas,scif-r8a779a0",
-				     "renesas,rcar-gen3-scif", "renesas,scif";
+				     "renesas,rcar-gen4-scif", "renesas,scif";
 			reg = <0 0xe6c50000 0 64>;
 			interrupts = <GIC_SPI 253 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 704>,
@@ -919,7 +992,7 @@
 
 		scif4: serial@e6c40000 {
 			compatible = "renesas,scif-r8a779a0",
-				     "renesas,rcar-gen3-scif", "renesas,scif";
+				     "renesas,rcar-gen4-scif", "renesas,scif";
 			reg = <0 0xe6c40000 0 64>;
 			interrupts = <GIC_SPI 254 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 705>,
@@ -1931,7 +2004,8 @@
 		};
 
 		dmac1: dma-controller@e7350000 {
-			compatible = "renesas,dmac-r8a779a0";
+			compatible = "renesas,dmac-r8a779a0",
+				     "renesas,rcar-gen4-dmac";
 			reg = <0 0xe7350000 0 0x1000>,
 			      <0 0xe7300000 0 0x10000>;
 			interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>,
@@ -1965,7 +2039,8 @@
 		};
 
 		dmac2: dma-controller@e7351000 {
-			compatible = "renesas,dmac-r8a779a0";
+			compatible = "renesas,dmac-r8a779a0",
+				     "renesas,rcar-gen4-dmac";
 			reg = <0 0xe7351000 0 0x1000>,
 			      <0 0xe7310000 0 0x10000>;
 			interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,
@@ -1990,10 +2065,11 @@
 
 		mmc0: mmc@ee140000 {
 			compatible = "renesas,sdhi-r8a779a0",
-				     "renesas,rcar-gen3-sdhi";
+				     "renesas,rcar-gen4-sdhi";
 			reg = <0 0xee140000 0 0x2000>;
 			interrupts = <GIC_SPI 236 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&cpg CPG_MOD 706>;
+			clocks = <&cpg CPG_MOD 706>, <&cpg CPG_CORE R8A779A0_CLK_SD0H>;
+			clock-names = "core", "clkh";
 			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
 			resets = <&cpg 706>;
 			max-frequency = <200000000>;
@@ -2010,7 +2086,6 @@
 			reg-names = "regs", "dirmap", "wbuf";
 			interrupts = <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD 629>;
-			clock-names = "rpc";
 			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
 			resets = <&cpg 629>;
 			#address-cells = <1>;
@@ -2019,7 +2094,8 @@
 		};
 
 		ipmmu_rt0: iommu@ee480000 {
-			compatible = "renesas,ipmmu-r8a779a0";
+			compatible = "renesas,ipmmu-r8a779a0",
+				     "renesas,rcar-gen4-ipmmu-vmsa";
 			reg = <0 0xee480000 0 0x20000>;
 			renesas,ipmmu-main = <&ipmmu_mm 10>;
 			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
@@ -2027,7 +2103,8 @@
 		};
 
 		ipmmu_rt1: iommu@ee4c0000 {
-			compatible = "renesas,ipmmu-r8a779a0";
+			compatible = "renesas,ipmmu-r8a779a0",
+				     "renesas,rcar-gen4-ipmmu-vmsa";
 			reg = <0 0xee4c0000 0 0x20000>;
 			renesas,ipmmu-main = <&ipmmu_mm 19>;
 			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
@@ -2035,7 +2112,8 @@
 		};
 
 		ipmmu_ds0: iommu@eed00000 {
-			compatible = "renesas,ipmmu-r8a779a0";
+			compatible = "renesas,ipmmu-r8a779a0",
+				     "renesas,rcar-gen4-ipmmu-vmsa";
 			reg = <0 0xeed00000 0 0x20000>;
 			renesas,ipmmu-main = <&ipmmu_mm 0>;
 			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
@@ -2043,7 +2121,8 @@
 		};
 
 		ipmmu_ds1: iommu@eed40000 {
-			compatible = "renesas,ipmmu-r8a779a0";
+			compatible = "renesas,ipmmu-r8a779a0",
+				     "renesas,rcar-gen4-ipmmu-vmsa";
 			reg = <0 0xeed40000 0 0x20000>;
 			renesas,ipmmu-main = <&ipmmu_mm 1>;
 			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
@@ -2051,7 +2130,8 @@
 		};
 
 		ipmmu_ir: iommu@eed80000 {
-			compatible = "renesas,ipmmu-r8a779a0";
+			compatible = "renesas,ipmmu-r8a779a0",
+				     "renesas,rcar-gen4-ipmmu-vmsa";
 			reg = <0 0xeed80000 0 0x20000>;
 			renesas,ipmmu-main = <&ipmmu_mm 3>;
 			power-domains = <&sysc R8A779A0_PD_A3IR>;
@@ -2059,7 +2139,8 @@
 		};
 
 		ipmmu_vc0: iommu@eedc0000 {
-			compatible = "renesas,ipmmu-r8a779a0";
+			compatible = "renesas,ipmmu-r8a779a0",
+				     "renesas,rcar-gen4-ipmmu-vmsa";
 			reg = <0 0xeedc0000 0 0x20000>;
 			renesas,ipmmu-main = <&ipmmu_mm 12>;
 			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
@@ -2067,7 +2148,8 @@
 		};
 
 		ipmmu_vi0: iommu@eee80000 {
-			compatible = "renesas,ipmmu-r8a779a0";
+			compatible = "renesas,ipmmu-r8a779a0",
+				     "renesas,rcar-gen4-ipmmu-vmsa";
 			reg = <0 0xeee80000 0 0x20000>;
 			renesas,ipmmu-main = <&ipmmu_mm 14>;
 			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
@@ -2075,7 +2157,8 @@
 		};
 
 		ipmmu_vi1: iommu@eeec0000 {
-			compatible = "renesas,ipmmu-r8a779a0";
+			compatible = "renesas,ipmmu-r8a779a0",
+				     "renesas,rcar-gen4-ipmmu-vmsa";
 			reg = <0 0xeeec0000 0 0x20000>;
 			renesas,ipmmu-main = <&ipmmu_mm 15>;
 			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
@@ -2083,7 +2166,8 @@
 		};
 
 		ipmmu_3dg: iommu@eee00000 {
-			compatible = "renesas,ipmmu-r8a779a0";
+			compatible = "renesas,ipmmu-r8a779a0",
+				     "renesas,rcar-gen4-ipmmu-vmsa";
 			reg = <0 0xeee00000 0 0x20000>;
 			renesas,ipmmu-main = <&ipmmu_mm 6>;
 			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
@@ -2091,7 +2175,8 @@
 		};
 
 		ipmmu_vip0: iommu@eef00000 {
-			compatible = "renesas,ipmmu-r8a779a0";
+			compatible = "renesas,ipmmu-r8a779a0",
+				     "renesas,rcar-gen4-ipmmu-vmsa";
 			reg = <0 0xeef00000 0 0x20000>;
 			renesas,ipmmu-main = <&ipmmu_mm 5>;
 			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
@@ -2099,7 +2184,8 @@
 		};
 
 		ipmmu_vip1: iommu@eef40000 {
-			compatible = "renesas,ipmmu-r8a779a0";
+			compatible = "renesas,ipmmu-r8a779a0",
+				     "renesas,rcar-gen4-ipmmu-vmsa";
 			reg = <0 0xeef40000 0 0x20000>;
 			renesas,ipmmu-main = <&ipmmu_mm 11>;
 			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
@@ -2107,7 +2193,8 @@
 		};
 
 		ipmmu_mm: iommu@eefc0000 {
-			compatible = "renesas,ipmmu-r8a779a0";
+			compatible = "renesas,ipmmu-r8a779a0",
+				     "renesas,rcar-gen4-ipmmu-vmsa";
 			reg = <0 0xeefc0000 0 0x20000>;
 			interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
@@ -2268,6 +2355,40 @@
 			};
 		};
 
+		du: display@feb00000 {
+			compatible = "renesas,du-r8a779a0";
+			reg = <0 0xfeb00000 0 0x40000>;
+			interrupts = <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 411>;
+			clock-names = "du.0";
+			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
+			resets = <&cpg 411>;
+			reset-names = "du.0";
+			renesas,vsps = <&vspd0 0>, <&vspd1 0>;
+
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+					du_out_dsi0: endpoint {
+						remote-endpoint = <&dsi0_in>;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+					du_out_dsi1: endpoint {
+						remote-endpoint = <&dsi1_in>;
+					};
+				};
+			};
+		};
+
 		isp0: isp@fed00000 {
 			compatible = "renesas,r8a779a0-isp";
 			reg = <0 0xfed00000 0 0x10000>;
@@ -2600,6 +2721,62 @@
 			};
 		};
 
+		dsi0: dsi-encoder@fed80000 {
+			compatible = "renesas,r8a779a0-dsi-csi2-tx";
+			reg = <0 0xfed80000 0 0x10000>;
+			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
+			clocks = <&cpg CPG_MOD 415>,
+				 <&cpg CPG_CORE R8A779A0_CLK_DSI>,
+				 <&cpg CPG_CORE R8A779A0_CLK_CL16MCK>;
+			clock-names = "fck", "dsi", "pll";
+			resets = <&cpg 415>;
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+					dsi0_in: endpoint {
+						remote-endpoint = <&du_out_dsi0>;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+				};
+			};
+		};
+
+		dsi1: dsi-encoder@fed90000 {
+			compatible = "renesas,r8a779a0-dsi-csi2-tx";
+			reg = <0 0xfed90000 0 0x10000>;
+			power-domains = <&sysc R8A779A0_PD_ALWAYS_ON>;
+			clocks = <&cpg CPG_MOD 416>,
+				 <&cpg CPG_CORE R8A779A0_CLK_DSI>,
+				 <&cpg CPG_CORE R8A779A0_CLK_CL16MCK>;
+			clock-names = "fck", "dsi", "pll";
+			resets = <&cpg 416>;
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+					dsi1_in: endpoint {
+						remote-endpoint = <&du_out_dsi1>;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+				};
+			};
+		};
+
 		prr: chipid@fff00044 {
 			compatible = "renesas,prr";
 			reg = <0 0xfff00044 0 4>;
@@ -2607,7 +2784,7 @@
 	};
 
 	thermal-zones {
-		sensor_thermal1: sensor-thermal1 {
+		sensor1_thermal: sensor1-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 			thermal-sensors = <&tsc 0>;
@@ -2621,7 +2798,7 @@
 			};
 		};
 
-		sensor_thermal2: sensor-thermal2 {
+		sensor2_thermal: sensor2-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 			thermal-sensors = <&tsc 1>;
@@ -2635,7 +2812,7 @@
 			};
 		};
 
-		sensor_thermal3: sensor-thermal3 {
+		sensor3_thermal: sensor3-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 			thermal-sensors = <&tsc 2>;
@@ -2649,7 +2826,7 @@
 			};
 		};
 
-		sensor_thermal4: sensor-thermal4 {
+		sensor4_thermal: sensor4-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 			thermal-sensors = <&tsc 3>;
@@ -2663,7 +2840,7 @@
 			};
 		};
 
-		sensor_thermal5: sensor-thermal5 {
+		sensor5_thermal: sensor5-thermal {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 			thermal-sensors = <&tsc 4>;
diff --git a/arch/arm64/boot/dts/renesas/r8a779f0-spider-cpu.dtsi b/arch/arm64/boot/dts/renesas/r8a779f0-spider-cpu.dtsi
new file mode 100644
index 000000000000..a45df1041705
--- /dev/null
+++ b/arch/arm64/boot/dts/renesas/r8a779f0-spider-cpu.dtsi
@@ -0,0 +1,152 @@
+// SPDX-License-Identifier: (GPL-2.0 or MIT)
+/*
+ * Device Tree Source for the Spider CPU board
+ *
+ * Copyright (C) 2021 Renesas Electronics Corp.
+ */
+
+#include "r8a779f0.dtsi"
+
+/ {
+	model = "Renesas Spider CPU board";
+	compatible = "renesas,spider-cpu", "renesas,r8a779f0";
+
+	aliases {
+		serial0 = &scif3;
+		serial1 = &scif0;
+	};
+
+	chosen {
+		bootargs = "ignore_loglevel rw root=/dev/nfs ip=on";
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@48000000 {
+		device_type = "memory";
+		/* first 128MB is reserved for secure area. */
+		reg = <0x0 0x48000000 0x0 0x78000000>;
+	};
+
+	memory@480000000 {
+		device_type = "memory";
+		reg = <0x4 0x80000000 0x0 0x80000000>;
+	};
+
+	reg_1p8v: regulator-1p8v {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-1.8V";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-3.3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+};
+
+&extal_clk {
+	clock-frequency = <20000000>;
+};
+
+&extalr_clk {
+	clock-frequency = <32768>;
+};
+
+&i2c4 {
+	pinctrl-0 = <&i2c4_pins>;
+	pinctrl-names = "default";
+
+	status = "okay";
+	clock-frequency = <400000>;
+
+	eeprom@50 {
+		compatible = "rohm,br24g01", "atmel,24c01";
+		label = "cpu-board";
+		reg = <0x50>;
+		pagesize = <8>;
+	};
+};
+
+/*
+ * This board also has a microSD slot which we will not support upstream
+ * because we cannot directly switch voltages in software.
+ */
+&mmc0 {
+	pinctrl-0 = <&mmc_pins>;
+	pinctrl-1 = <&mmc_pins>;
+	pinctrl-names = "default", "state_uhs";
+
+	vmmc-supply = <&reg_3p3v>;
+	vqmmc-supply = <&reg_1p8v>;
+	mmc-hs200-1_8v;
+	mmc-hs400-1_8v;
+	bus-width = <8>;
+	no-sd;
+	no-sdio;
+	non-removable;
+	full-pwr-cycle-in-suspend;
+	status = "okay";
+};
+
+&pfc {
+	pinctrl-0 = <&scif_clk_pins>;
+	pinctrl-names = "default";
+
+	i2c4_pins: i2c4 {
+		groups = "i2c4";
+		function = "i2c4";
+	};
+
+	mmc_pins: mmc {
+		groups = "mmc_data8", "mmc_ctrl", "mmc_ds";
+		function = "mmc";
+		power-source = <1800>;
+	};
+
+	scif0_pins: scif0 {
+		groups = "scif0_data", "scif0_ctrl";
+		function = "scif0";
+	};
+
+	scif3_pins: scif3 {
+		groups = "scif3_data", "scif3_ctrl";
+		function = "scif3";
+	};
+
+	scif_clk_pins: scif_clk {
+		groups = "scif_clk";
+		function = "scif_clk";
+	};
+};
+
+&rwdt {
+	timeout-sec = <60>;
+	status = "okay";
+};
+
+&scif0 {
+	pinctrl-0 = <&scif0_pins>;
+	pinctrl-names = "default";
+
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&scif3 {
+	pinctrl-0 = <&scif3_pins>;
+	pinctrl-names = "default";
+
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&scif_clk {
+	clock-frequency = <24000000>;
+};
diff --git a/arch/arm64/boot/dts/renesas/r8a779f0-spider-ethernet.dtsi b/arch/arm64/boot/dts/renesas/r8a779f0-spider-ethernet.dtsi
new file mode 100644
index 000000000000..15e8d1ebf575
--- /dev/null
+++ b/arch/arm64/boot/dts/renesas/r8a779f0-spider-ethernet.dtsi
@@ -0,0 +1,15 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device Tree Source for the Spider Ethernet sub-board
+ *
+ * Copyright (C) 2021 Renesas Electronics Corp.
+ */
+
+&i2c4 {
+	eeprom@52 {
+		compatible = "rohm,br24g01", "atmel,24c01";
+		label = "ethernet-sub-board";
+		reg = <0x52>;
+		pagesize = <8>;
+	};
+};
diff --git a/arch/arm64/boot/dts/renesas/r8a779f0-spider.dts b/arch/arm64/boot/dts/renesas/r8a779f0-spider.dts
new file mode 100644
index 000000000000..7aac3f4d319c
--- /dev/null
+++ b/arch/arm64/boot/dts/renesas/r8a779f0-spider.dts
@@ -0,0 +1,24 @@
+// SPDX-License-Identifier: (GPL-2.0 or MIT)
+/*
+ * Device Tree Source for the Spider CPU and BreakOut boards
+ *
+ * Copyright (C) 2021 Renesas Electronics Corp.
+ */
+
+/dts-v1/;
+#include "r8a779f0-spider-cpu.dtsi"
+#include "r8a779f0-spider-ethernet.dtsi"
+
+/ {
+	model = "Renesas Spider CPU and Breakout boards based on r8a779f0";
+	compatible = "renesas,spider-breakout", "renesas,spider-cpu", "renesas,r8a779f0";
+};
+
+&i2c4 {
+	eeprom@51 {
+		compatible = "rohm,br24g01", "atmel,24c01";
+		label = "breakout-board";
+		reg = <0x51>;
+		pagesize = <8>;
+	};
+};
diff --git a/arch/arm64/boot/dts/renesas/r8a779f0.dtsi b/arch/arm64/boot/dts/renesas/r8a779f0.dtsi
new file mode 100644
index 000000000000..c2f152bcf10e
--- /dev/null
+++ b/arch/arm64/boot/dts/renesas/r8a779f0.dtsi
@@ -0,0 +1,1006 @@
+// SPDX-License-Identifier: (GPL-2.0 or MIT)
+/*
+ * Device Tree Source for the R-Car S4-8 (R8A779F0) SoC
+ *
+ * Copyright (C) 2021 Renesas Electronics Corp.
+ */
+
+#include <dt-bindings/clock/r8a779f0-cpg-mssr.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/power/r8a779f0-sysc.h>
+
+/ {
+	compatible = "renesas,r8a779f0";
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu-map {
+			cluster0 {
+				core0 {
+					cpu = <&a55_0>;
+				};
+				core1 {
+					cpu = <&a55_1>;
+				};
+			};
+
+			cluster1 {
+				core0 {
+					cpu = <&a55_2>;
+				};
+				core1 {
+					cpu = <&a55_3>;
+				};
+			};
+
+			cluster2 {
+				core0 {
+					cpu = <&a55_4>;
+				};
+				core1 {
+					cpu = <&a55_5>;
+				};
+			};
+
+			cluster3 {
+				core0 {
+					cpu = <&a55_6>;
+				};
+				core1 {
+					cpu = <&a55_7>;
+				};
+			};
+		};
+
+		a55_0: cpu@0 {
+			compatible = "arm,cortex-a55";
+			reg = <0>;
+			device_type = "cpu";
+			power-domains = <&sysc R8A779F0_PD_A1E0D0C0>;
+			next-level-cache = <&L3_CA55_0>;
+			enable-method = "psci";
+			cpu-idle-states = <&CPU_SLEEP_0>;
+			clocks = <&cpg CPG_CORE R8A779F0_CLK_Z0>;
+		};
+
+		a55_1: cpu@100 {
+			compatible = "arm,cortex-a55";
+			reg = <0x100>;
+			device_type = "cpu";
+			power-domains = <&sysc R8A779F0_PD_A1E0D0C1>;
+			next-level-cache = <&L3_CA55_0>;
+			enable-method = "psci";
+			cpu-idle-states = <&CPU_SLEEP_0>;
+			clocks = <&cpg CPG_CORE R8A779F0_CLK_Z0>;
+		};
+
+		a55_2: cpu@10000 {
+			compatible = "arm,cortex-a55";
+			reg = <0x10000>;
+			device_type = "cpu";
+			power-domains = <&sysc R8A779F0_PD_A1E0D1C0>;
+			next-level-cache = <&L3_CA55_1>;
+			enable-method = "psci";
+			cpu-idle-states = <&CPU_SLEEP_0>;
+			clocks = <&cpg CPG_CORE R8A779F0_CLK_Z0>;
+		};
+
+		a55_3: cpu@10100 {
+			compatible = "arm,cortex-a55";
+			reg = <0x10100>;
+			device_type = "cpu";
+			power-domains = <&sysc R8A779F0_PD_A1E0D1C1>;
+			next-level-cache = <&L3_CA55_1>;
+			enable-method = "psci";
+			cpu-idle-states = <&CPU_SLEEP_0>;
+			clocks = <&cpg CPG_CORE R8A779F0_CLK_Z0>;
+		};
+
+		a55_4: cpu@20000 {
+			compatible = "arm,cortex-a55";
+			reg = <0x20000>;
+			device_type = "cpu";
+			power-domains = <&sysc R8A779F0_PD_A1E1D0C0>;
+			next-level-cache = <&L3_CA55_2>;
+			enable-method = "psci";
+			cpu-idle-states = <&CPU_SLEEP_0>;
+			clocks = <&cpg CPG_CORE R8A779F0_CLK_Z1>;
+		};
+
+		a55_5: cpu@20100 {
+			compatible = "arm,cortex-a55";
+			reg = <0x20100>;
+			device_type = "cpu";
+			power-domains = <&sysc R8A779F0_PD_A1E1D0C1>;
+			next-level-cache = <&L3_CA55_2>;
+			enable-method = "psci";
+			cpu-idle-states = <&CPU_SLEEP_0>;
+			clocks = <&cpg CPG_CORE R8A779F0_CLK_Z1>;
+		};
+
+		a55_6: cpu@30000 {
+			compatible = "arm,cortex-a55";
+			reg = <0x30000>;
+			device_type = "cpu";
+			power-domains = <&sysc R8A779F0_PD_A1E1D1C0>;
+			next-level-cache = <&L3_CA55_3>;
+			enable-method = "psci";
+			cpu-idle-states = <&CPU_SLEEP_0>;
+			clocks = <&cpg CPG_CORE R8A779F0_CLK_Z1>;
+		};
+
+		a55_7: cpu@30100 {
+			compatible = "arm,cortex-a55";
+			reg = <0x30100>;
+			device_type = "cpu";
+			power-domains = <&sysc R8A779F0_PD_A1E1D1C1>;
+			next-level-cache = <&L3_CA55_3>;
+			enable-method = "psci";
+			cpu-idle-states = <&CPU_SLEEP_0>;
+			clocks = <&cpg CPG_CORE R8A779F0_CLK_Z1>;
+		};
+
+		L3_CA55_0: cache-controller-0 {
+			compatible = "cache";
+			power-domains = <&sysc R8A779F0_PD_A2E0D0>;
+			cache-unified;
+			cache-level = <3>;
+		};
+
+		L3_CA55_1: cache-controller-1 {
+			compatible = "cache";
+			power-domains = <&sysc R8A779F0_PD_A2E0D1>;
+			cache-unified;
+			cache-level = <3>;
+		};
+
+		L3_CA55_2: cache-controller-2 {
+			compatible = "cache";
+			power-domains = <&sysc R8A779F0_PD_A2E1D0>;
+			cache-unified;
+			cache-level = <3>;
+		};
+
+		L3_CA55_3: cache-controller-3 {
+			compatible = "cache";
+			power-domains = <&sysc R8A779F0_PD_A2E1D1>;
+			cache-unified;
+			cache-level = <3>;
+		};
+
+		idle-states {
+			entry-method = "psci";
+
+			CPU_SLEEP_0: cpu-sleep-0 {
+				compatible = "arm,idle-state";
+				arm,psci-suspend-param = <0x0010000>;
+				local-timer-stop;
+				entry-latency-us = <400>;
+				exit-latency-us = <500>;
+				min-residency-us = <4000>;
+			};
+		};
+	};
+
+	extal_clk: extal {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		/* This value must be overridden by the board */
+		clock-frequency = <0>;
+	};
+
+	extalr_clk: extalr {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		/* This value must be overridden by the board */
+		clock-frequency = <0>;
+	};
+
+	pmu_a55 {
+		compatible = "arm,cortex-a55-pmu";
+		interrupts-extended = <&gic GIC_PPI 7 IRQ_TYPE_LEVEL_LOW>;
+	};
+
+	psci {
+		compatible = "arm,psci-1.0", "arm,psci-0.2";
+		method = "smc";
+	};
+
+	/* External SCIF clock - to be overridden by boards that provide it */
+	scif_clk: scif {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <0>;
+	};
+
+	soc: soc {
+		compatible = "simple-bus";
+		interrupt-parent = <&gic>;
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		rwdt: watchdog@e6020000 {
+			compatible = "renesas,r8a779f0-wdt",
+				     "renesas,rcar-gen4-wdt";
+			reg = <0 0xe6020000 0 0x0c>;
+			interrupts = <GIC_SPI 515 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 907>;
+			power-domains = <&sysc R8A779F0_PD_ALWAYS_ON>;
+			resets = <&cpg 907>;
+			status = "disabled";
+		};
+
+		pfc: pinctrl@e6050000 {
+			compatible = "renesas,pfc-r8a779f0";
+			reg = <0 0xe6050000 0 0x16c>, <0 0xe6050800 0 0x16c>,
+			      <0 0xe6051000 0 0x16c>, <0 0xe6051800 0 0x16c>;
+		};
+
+		gpio0: gpio@e6050180 {
+			compatible = "renesas,gpio-r8a779f0",
+				     "renesas,rcar-gen4-gpio";
+			reg = <0 0xe6050180 0 0x54>;
+			interrupts = <GIC_SPI 822 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 915>;
+			power-domains = <&sysc R8A779F0_PD_ALWAYS_ON>;
+			resets = <&cpg 915>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&pfc 0 0 21>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpio1: gpio@e6050980 {
+			compatible = "renesas,gpio-r8a779f0",
+				     "renesas,rcar-gen4-gpio";
+			reg = <0 0xe6050980 0 0x54>;
+			interrupts = <GIC_SPI 823 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 915>;
+			power-domains = <&sysc R8A779F0_PD_ALWAYS_ON>;
+			resets = <&cpg 915>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&pfc 0 32 25>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpio2: gpio@e6051180 {
+			compatible = "renesas,gpio-r8a779f0",
+				     "renesas,rcar-gen4-gpio";
+			reg = <0 0xe6051180 0 0x54>;
+			interrupts = <GIC_SPI 824 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 915>;
+			power-domains = <&sysc R8A779F0_PD_ALWAYS_ON>;
+			resets = <&cpg 915>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&pfc 0 64 17>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpio3: gpio@e6051980 {
+			compatible = "renesas,gpio-r8a779f0",
+				     "renesas,rcar-gen4-gpio";
+			reg = <0 0xe6051980 0 0x54>;
+			interrupts = <GIC_SPI 825 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 915>;
+			power-domains = <&sysc R8A779F0_PD_ALWAYS_ON>;
+			resets = <&cpg 915>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&pfc 0 96 19>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		cmt0: timer@e60f0000 {
+			compatible = "renesas,r8a779f0-cmt0",
+				     "renesas,rcar-gen4-cmt0";
+			reg = <0 0xe60f0000 0 0x1004>;
+			interrupts = <GIC_SPI 448 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 449 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 910>;
+			clock-names = "fck";
+			power-domains = <&sysc R8A779F0_PD_ALWAYS_ON>;
+			resets = <&cpg 910>;
+			status = "disabled";
+		};
+
+		cmt1: timer@e6130000 {
+			compatible = "renesas,r8a779f0-cmt1",
+				     "renesas,rcar-gen4-cmt1";
+			reg = <0 0xe6130000 0 0x1004>;
+			interrupts = <GIC_SPI 450 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 451 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 452 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 453 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 454 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 455 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 456 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 457 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 911>;
+			clock-names = "fck";
+			power-domains = <&sysc R8A779F0_PD_ALWAYS_ON>;
+			resets = <&cpg 911>;
+			status = "disabled";
+		};
+
+		cmt2: timer@e6140000 {
+			compatible = "renesas,r8a779f0-cmt1",
+				     "renesas,rcar-gen4-cmt1";
+			reg = <0 0xe6140000 0 0x1004>;
+			interrupts = <GIC_SPI 458 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 459 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 460 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 461 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 462 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 463 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 464 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 465 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 912>;
+			clock-names = "fck";
+			power-domains = <&sysc R8A779F0_PD_ALWAYS_ON>;
+			resets = <&cpg 912>;
+			status = "disabled";
+		};
+
+		cmt3: timer@e6148000 {
+			compatible = "renesas,r8a779f0-cmt1",
+				     "renesas,rcar-gen4-cmt1";
+			reg = <0 0xe6148000 0 0x1004>;
+			interrupts = <GIC_SPI 466 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 467 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 468 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 469 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 470 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 471 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 472 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 473 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 913>;
+			clock-names = "fck";
+			power-domains = <&sysc R8A779F0_PD_ALWAYS_ON>;
+			resets = <&cpg 913>;
+			status = "disabled";
+		};
+
+		cpg: clock-controller@e6150000 {
+			compatible = "renesas,r8a779f0-cpg-mssr";
+			reg = <0 0xe6150000 0 0x4000>;
+			clocks = <&extal_clk>, <&extalr_clk>;
+			clock-names = "extal", "extalr";
+			#clock-cells = <2>;
+			#power-domain-cells = <0>;
+			#reset-cells = <1>;
+		};
+
+		rst: reset-controller@e6160000 {
+			compatible = "renesas,r8a779f0-rst";
+			reg = <0 0xe6160000 0 0x4000>;
+		};
+
+		sysc: system-controller@e6180000 {
+			compatible = "renesas,r8a779f0-sysc";
+			reg = <0 0xe6180000 0 0x4000>;
+			#power-domain-cells = <1>;
+		};
+
+		tsc: thermal@e6198000 {
+			compatible = "renesas,r8a779f0-thermal";
+			/* The 4th sensor is in control domain and not for Linux */
+			reg = <0 0xe6198000 0 0x200>,
+			      <0 0xe61a0000 0 0x200>,
+			      <0 0xe61a8000 0 0x200>;
+			clocks = <&cpg CPG_MOD 919>;
+			power-domains = <&sysc R8A779F0_PD_ALWAYS_ON>;
+			resets = <&cpg 919>;
+			#thermal-sensor-cells = <1>;
+		};
+
+		tmu0: timer@e61e0000 {
+			compatible = "renesas,tmu-r8a779f0", "renesas,tmu";
+			reg = <0 0xe61e0000 0 0x30>;
+			interrupts = <GIC_SPI 474 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 475 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 476 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 713>;
+			clock-names = "fck";
+			power-domains = <&sysc R8A779F0_PD_ALWAYS_ON>;
+			resets = <&cpg 713>;
+			status = "disabled";
+		};
+
+		tmu1: timer@e6fc0000 {
+			compatible = "renesas,tmu-r8a779f0", "renesas,tmu";
+			reg = <0 0xe6fc0000 0 0x30>;
+			interrupts = <GIC_SPI 477 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 478 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 479 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 714>;
+			clock-names = "fck";
+			power-domains = <&sysc R8A779F0_PD_ALWAYS_ON>;
+			resets = <&cpg 714>;
+			status = "disabled";
+		};
+
+		tmu2: timer@e6fd0000 {
+			compatible = "renesas,tmu-r8a779f0", "renesas,tmu";
+			reg = <0 0xe6fd0000 0 0x30>;
+			interrupts = <GIC_SPI 481 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 482 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 483 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 715>;
+			clock-names = "fck";
+			power-domains = <&sysc R8A779F0_PD_ALWAYS_ON>;
+			resets = <&cpg 715>;
+			status = "disabled";
+		};
+
+		tmu3: timer@e6fe0000 {
+			compatible = "renesas,tmu-r8a779f0", "renesas,tmu";
+			reg = <0 0xe6fe0000 0 0x30>;
+			interrupts = <GIC_SPI 485 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 486 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 487 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 716>;
+			clock-names = "fck";
+			power-domains = <&sysc R8A779F0_PD_ALWAYS_ON>;
+			resets = <&cpg 716>;
+			status = "disabled";
+		};
+
+		tmu4: timer@ffc00000 {
+			compatible = "renesas,tmu-r8a779f0", "renesas,tmu";
+			reg = <0 0xffc00000 0 0x30>;
+			interrupts = <GIC_SPI 489 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 490 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 491 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 717>;
+			clock-names = "fck";
+			power-domains = <&sysc R8A779F0_PD_ALWAYS_ON>;
+			resets = <&cpg 717>;
+			status = "disabled";
+		};
+
+		i2c0: i2c@e6500000 {
+			compatible = "renesas,i2c-r8a779f0",
+				     "renesas,rcar-gen4-i2c";
+			reg = <0 0xe6500000 0 0x40>;
+			interrupts = <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 518>;
+			power-domains = <&sysc R8A779F0_PD_ALWAYS_ON>;
+			resets = <&cpg 518>;
+			dmas = <&dmac0 0x91>, <&dmac0 0x90>,
+			       <&dmac1 0x91>, <&dmac1 0x90>;
+			dma-names = "tx", "rx", "tx", "rx";
+			i2c-scl-internal-delay-ns = <110>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i2c1: i2c@e6508000 {
+			compatible = "renesas,i2c-r8a779f0",
+				     "renesas,rcar-gen4-i2c";
+			reg = <0 0xe6508000 0 0x40>;
+			interrupts = <GIC_SPI 239 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 519>;
+			power-domains = <&sysc R8A779F0_PD_ALWAYS_ON>;
+			resets = <&cpg 519>;
+			dmas = <&dmac0 0x93>, <&dmac0 0x92>,
+			       <&dmac1 0x93>, <&dmac1 0x92>;
+			dma-names = "tx", "rx", "tx", "rx";
+			i2c-scl-internal-delay-ns = <110>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i2c2: i2c@e6510000 {
+			compatible = "renesas,i2c-r8a779f0",
+				     "renesas,rcar-gen4-i2c";
+			reg = <0 0xe6510000 0 0x40>;
+			interrupts = <0 240 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 520>;
+			power-domains = <&sysc R8A779F0_PD_ALWAYS_ON>;
+			resets = <&cpg 520>;
+			dmas = <&dmac0 0x95>, <&dmac0 0x94>,
+			       <&dmac1 0x95>, <&dmac1 0x94>;
+			dma-names = "tx", "rx", "tx", "rx";
+			i2c-scl-internal-delay-ns = <110>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i2c3: i2c@e66d0000 {
+			compatible = "renesas,i2c-r8a779f0",
+				     "renesas,rcar-gen4-i2c";
+			reg = <0 0xe66d0000 0 0x40>;
+			interrupts = <GIC_SPI 241 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 521>;
+			power-domains = <&sysc R8A779F0_PD_ALWAYS_ON>;
+			resets = <&cpg 521>;
+			dmas = <&dmac0 0x97>, <&dmac0 0x96>,
+			       <&dmac1 0x97>, <&dmac1 0x96>;
+			dma-names = "tx", "rx", "tx", "rx";
+			i2c-scl-internal-delay-ns = <110>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i2c4: i2c@e66d8000 {
+			compatible = "renesas,i2c-r8a779f0",
+				     "renesas,rcar-gen4-i2c";
+			reg = <0 0xe66d8000 0 0x40>;
+			interrupts = <GIC_SPI 242 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 522>;
+			power-domains = <&sysc R8A779F0_PD_ALWAYS_ON>;
+			resets = <&cpg 522>;
+			dmas = <&dmac0 0x99>, <&dmac0 0x98>,
+			       <&dmac1 0x99>, <&dmac1 0x98>;
+			dma-names = "tx", "rx", "tx", "rx";
+			i2c-scl-internal-delay-ns = <110>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i2c5: i2c@e66e0000 {
+			compatible = "renesas,i2c-r8a779f0",
+				     "renesas,rcar-gen4-i2c";
+			reg = <0 0xe66e0000 0 0x40>;
+			interrupts = <GIC_SPI 243 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 523>;
+			power-domains = <&sysc R8A779F0_PD_ALWAYS_ON>;
+			resets = <&cpg 523>;
+			dmas = <&dmac0 0x9b>, <&dmac0 0x9a>,
+			       <&dmac1 0x9b>, <&dmac1 0x9a>;
+			dma-names = "tx", "rx", "tx", "rx";
+			i2c-scl-internal-delay-ns = <110>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		hscif0: serial@e6540000 {
+			compatible = "renesas,hscif-r8a779f0",
+				     "renesas,rcar-gen4-hscif", "renesas,hscif";
+			reg = <0 0xe6540000 0 0x60>;
+			interrupts = <GIC_SPI 245 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 514>,
+				 <&cpg CPG_CORE R8A779F0_CLK_S0D3>,
+				 <&scif_clk>;
+			clock-names = "fck", "brg_int", "scif_clk";
+			dmas = <&dmac0 0x31>, <&dmac0 0x30>,
+			       <&dmac1 0x31>, <&dmac1 0x30>;
+			dma-names = "tx", "rx", "tx", "rx";
+			power-domains = <&sysc R8A779F0_PD_ALWAYS_ON>;
+			resets = <&cpg 514>;
+			status = "disabled";
+		};
+
+		hscif1: serial@e6550000 {
+			compatible = "renesas,hscif-r8a779f0",
+				     "renesas,rcar-gen4-hscif", "renesas,hscif";
+			reg = <0 0xe6550000 0 0x60>;
+			interrupts = <GIC_SPI 246 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 515>,
+				 <&cpg CPG_CORE R8A779F0_CLK_S0D3>,
+				 <&scif_clk>;
+			clock-names = "fck", "brg_int", "scif_clk";
+			dmas = <&dmac0 0x33>, <&dmac0 0x32>,
+			       <&dmac1 0x33>, <&dmac1 0x32>;
+			dma-names = "tx", "rx", "tx", "rx";
+			power-domains = <&sysc R8A779F0_PD_ALWAYS_ON>;
+			resets = <&cpg 515>;
+			status = "disabled";
+		};
+
+		hscif2: serial@e6560000 {
+			compatible = "renesas,hscif-r8a779f0",
+				     "renesas,rcar-gen4-hscif", "renesas,hscif";
+			reg = <0 0xe6560000 0 0x60>;
+			interrupts = <GIC_SPI 247 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 516>,
+				 <&cpg CPG_CORE R8A779F0_CLK_S0D3>,
+				 <&scif_clk>;
+			clock-names = "fck", "brg_int", "scif_clk";
+			dmas = <&dmac0 0x35>, <&dmac0 0x34>,
+			       <&dmac1 0x35>, <&dmac1 0x34>;
+			dma-names = "tx", "rx", "tx", "rx";
+			power-domains = <&sysc R8A779F0_PD_ALWAYS_ON>;
+			resets = <&cpg 516>;
+			status = "disabled";
+		};
+
+		hscif3: serial@e66a0000 {
+			compatible = "renesas,hscif-r8a779f0",
+				     "renesas,rcar-gen4-hscif", "renesas,hscif";
+			reg = <0 0xe66a0000 0 0x60>;
+			interrupts = <GIC_SPI 248 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 517>,
+				 <&cpg CPG_CORE R8A779F0_CLK_S0D3>,
+				 <&scif_clk>;
+			clock-names = "fck", "brg_int", "scif_clk";
+			dmas = <&dmac0 0x37>, <&dmac0 0x36>,
+			       <&dmac1 0x37>, <&dmac1 0x36>;
+			dma-names = "tx", "rx", "tx", "rx";
+			power-domains = <&sysc R8A779F0_PD_ALWAYS_ON>;
+			resets = <&cpg 517>;
+			status = "disabled";
+		};
+
+		ufs: ufs@e6860000 {
+			compatible = "renesas,r8a779f0-ufs";
+			reg = <0 0xe6860000 0 0x100>;
+			interrupts = <GIC_SPI 235 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 1514>, <&ufs30_clk>;
+			clock-names = "fck", "ref_clk";
+			freq-table-hz = <200000000 200000000>, <38400000 38400000>;
+			power-domains = <&sysc R8A779F0_PD_ALWAYS_ON>;
+			resets = <&cpg 1514>;
+			status = "disabled";
+		};
+
+		scif0: serial@e6e60000 {
+			compatible = "renesas,scif-r8a779f0",
+				     "renesas,rcar-gen4-scif", "renesas,scif";
+			reg = <0 0xe6e60000 0 64>;
+			interrupts = <GIC_SPI 249 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 702>,
+				 <&cpg CPG_CORE R8A779F0_CLK_S0D3_PER>,
+				 <&scif_clk>;
+			clock-names = "fck", "brg_int", "scif_clk";
+			dmas = <&dmac0 0x51>, <&dmac0 0x50>,
+			       <&dmac1 0x51>, <&dmac1 0x50>;
+			dma-names = "tx", "rx", "tx", "rx";
+			power-domains = <&sysc R8A779F0_PD_ALWAYS_ON>;
+			resets = <&cpg 702>;
+			status = "disabled";
+		};
+
+		scif1: serial@e6e68000 {
+			compatible = "renesas,scif-r8a779f0",
+				     "renesas,rcar-gen4-scif", "renesas,scif";
+			reg = <0 0xe6e68000 0 64>;
+			interrupts = <GIC_SPI 250 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 703>,
+				 <&cpg CPG_CORE R8A779F0_CLK_S0D3_PER>,
+				 <&scif_clk>;
+			clock-names = "fck", "brg_int", "scif_clk";
+			dmas = <&dmac0 0x53>, <&dmac0 0x52>,
+			       <&dmac1 0x53>, <&dmac1 0x52>;
+			dma-names = "tx", "rx", "tx", "rx";
+			power-domains = <&sysc R8A779F0_PD_ALWAYS_ON>;
+			resets = <&cpg 703>;
+			status = "disabled";
+		};
+
+		scif3: serial@e6c50000 {
+			compatible = "renesas,scif-r8a779f0",
+				     "renesas,rcar-gen4-scif", "renesas,scif";
+			reg = <0 0xe6c50000 0 64>;
+			interrupts = <GIC_SPI 252 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 704>,
+				 <&cpg CPG_CORE R8A779F0_CLK_S0D3_PER>,
+				 <&scif_clk>;
+			clock-names = "fck", "brg_int", "scif_clk";
+			dmas = <&dmac0 0x57>, <&dmac0 0x56>,
+			       <&dmac1 0x57>, <&dmac1 0x56>;
+			dma-names = "tx", "rx", "tx", "rx";
+			power-domains = <&sysc R8A779F0_PD_ALWAYS_ON>;
+			resets = <&cpg 704>;
+			status = "disabled";
+		};
+
+		scif4: serial@e6c40000 {
+			compatible = "renesas,scif-r8a779f0",
+				     "renesas,rcar-gen4-scif", "renesas,scif";
+			reg = <0 0xe6c40000 0 64>;
+			interrupts = <GIC_SPI 253 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 705>,
+				 <&cpg CPG_CORE R8A779F0_CLK_S0D3_PER>,
+				 <&scif_clk>;
+			clock-names = "fck", "brg_int", "scif_clk";
+			dmas = <&dmac0 0x59>, <&dmac0 0x58>,
+			       <&dmac1 0x59>, <&dmac1 0x58>;
+			dma-names = "tx", "rx", "tx", "rx";
+			power-domains = <&sysc R8A779F0_PD_ALWAYS_ON>;
+			resets = <&cpg 705>;
+			status = "disabled";
+		};
+
+		msiof0: spi@e6e90000 {
+			compatible = "renesas,msiof-r8a779f0",
+				     "renesas,rcar-gen4-msiof";
+			reg = <0 0xe6e90000 0 0x0064>;
+			interrupts = <GIC_SPI 230 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 618>;
+			dmas = <&dmac0 0x41>, <&dmac0 0x40>,
+			       <&dmac1 0x41>, <&dmac1 0x40>;
+			dma-names = "tx", "rx", "tx", "rx";
+			power-domains = <&sysc R8A779F0_PD_ALWAYS_ON>;
+			resets = <&cpg 618>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		msiof1: spi@e6ea0000 {
+			compatible = "renesas,msiof-r8a779f0",
+				     "renesas,rcar-gen4-msiof";
+			reg = <0 0xe6ea0000 0 0x0064>;
+			interrupts = <GIC_SPI 231 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 619>;
+			dmas = <&dmac0 0x43>, <&dmac0 0x42>,
+			       <&dmac1 0x43>, <&dmac1 0x42>;
+			dma-names = "tx", "rx", "tx", "rx";
+			power-domains = <&sysc R8A779F0_PD_ALWAYS_ON>;
+			resets = <&cpg 619>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		msiof2: spi@e6c00000 {
+			compatible = "renesas,msiof-r8a779f0",
+				     "renesas,rcar-gen4-msiof";
+			reg = <0 0xe6c00000 0 0x0064>;
+			interrupts = <GIC_SPI 232 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 620>;
+			dmas = <&dmac0 0x45>, <&dmac0 0x44>,
+			       <&dmac1 0x45>, <&dmac1 0x44>;
+			dma-names = "tx", "rx", "tx", "rx";
+			power-domains = <&sysc R8A779F0_PD_ALWAYS_ON>;
+			resets = <&cpg 620>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		msiof3: spi@e6c10000 {
+			compatible = "renesas,msiof-r8a779f0",
+				     "renesas,rcar-gen4-msiof";
+			reg = <0 0xe6c10000 0 0x0064>;
+			interrupts = <GIC_SPI 233 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 621>;
+			dmas = <&dmac0 0x47>, <&dmac0 0x46>,
+			       <&dmac1 0x47>, <&dmac1 0x46>;
+			dma-names = "tx", "rx", "tx", "rx";
+			power-domains = <&sysc R8A779F0_PD_ALWAYS_ON>;
+			resets = <&cpg 621>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		dmac0: dma-controller@e7350000 {
+			compatible = "renesas,dmac-r8a779f0",
+				     "renesas,rcar-gen4-dmac";
+			reg = <0 0xe7350000 0 0x1000>,
+			      <0 0xe7300000 0 0x10000>;
+			interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "error",
+					  "ch0", "ch1", "ch2", "ch3", "ch4",
+					  "ch5", "ch6", "ch7", "ch8", "ch9",
+					  "ch10", "ch11", "ch12", "ch13",
+					  "ch14", "ch15";
+			clocks = <&cpg CPG_MOD 709>;
+			clock-names = "fck";
+			power-domains = <&sysc R8A779F0_PD_ALWAYS_ON>;
+			resets = <&cpg 709>;
+			#dma-cells = <1>;
+			dma-channels = <16>;
+			iommus = <&ipmmu_ds0 0>, <&ipmmu_ds0 1>,
+				 <&ipmmu_ds0 2>, <&ipmmu_ds0 3>,
+				 <&ipmmu_ds0 4>, <&ipmmu_ds0 5>,
+				 <&ipmmu_ds0 6>, <&ipmmu_ds0 7>,
+				 <&ipmmu_ds0 8>, <&ipmmu_ds0 9>,
+				 <&ipmmu_ds0 10>, <&ipmmu_ds0 11>,
+				 <&ipmmu_ds0 12>, <&ipmmu_ds0 13>,
+				 <&ipmmu_ds0 14>, <&ipmmu_ds0 15>;
+		};
+
+		dmac1: dma-controller@e7351000 {
+			compatible = "renesas,dmac-r8a779f0",
+				     "renesas,rcar-gen4-dmac";
+			reg = <0 0xe7351000 0 0x1000>,
+			      <0 0xe7310000 0 0x10000>;
+			interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 150 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 151 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 152 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "error",
+					  "ch0", "ch1", "ch2", "ch3", "ch4",
+					  "ch5", "ch6", "ch7", "ch8", "ch9",
+					  "ch10", "ch11", "ch12", "ch13",
+					  "ch14", "ch15";
+			clocks = <&cpg CPG_MOD 710>;
+			clock-names = "fck";
+			power-domains = <&sysc R8A779F0_PD_ALWAYS_ON>;
+			resets = <&cpg 710>;
+			#dma-cells = <1>;
+			dma-channels = <16>;
+			iommus = <&ipmmu_ds0 16>, <&ipmmu_ds0 17>,
+				 <&ipmmu_ds0 18>, <&ipmmu_ds0 19>,
+				 <&ipmmu_ds0 20>, <&ipmmu_ds0 21>,
+				 <&ipmmu_ds0 22>, <&ipmmu_ds0 23>,
+				 <&ipmmu_ds0 24>, <&ipmmu_ds0 25>,
+				 <&ipmmu_ds0 26>, <&ipmmu_ds0 27>,
+				 <&ipmmu_ds0 28>, <&ipmmu_ds0 29>,
+				 <&ipmmu_ds0 30>, <&ipmmu_ds0 31>;
+		};
+
+		mmc0: mmc@ee140000 {
+			compatible = "renesas,sdhi-r8a779f0",
+				     "renesas,rcar-gen4-sdhi";
+			reg = <0 0xee140000 0 0x2000>;
+			interrupts = <GIC_SPI 236 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 706>, <&cpg CPG_CORE R8A779F0_CLK_SD0H>;
+			clock-names = "core", "clkh";
+			power-domains = <&sysc R8A779F0_PD_ALWAYS_ON>;
+			resets = <&cpg 706>;
+			max-frequency = <200000000>;
+			status = "disabled";
+		};
+
+		ipmmu_rt0: iommu@ee480000 {
+			compatible = "renesas,ipmmu-r8a779f0",
+				     "renesas,rcar-gen4-ipmmu-vmsa";
+			reg = <0 0xee480000 0 0x20000>;
+			renesas,ipmmu-main = <&ipmmu_mm 10>;
+			power-domains = <&sysc R8A779F0_PD_ALWAYS_ON>;
+			#iommu-cells = <1>;
+		};
+
+		ipmmu_rt1: iommu@ee4c0000 {
+			compatible = "renesas,ipmmu-r8a779f0",
+				     "renesas,rcar-gen4-ipmmu-vmsa";
+			reg = <0 0xee4c0000 0 0x20000>;
+			renesas,ipmmu-main = <&ipmmu_mm 19>;
+			power-domains = <&sysc R8A779F0_PD_ALWAYS_ON>;
+			#iommu-cells = <1>;
+		};
+
+		ipmmu_ds0: iommu@eed00000 {
+			compatible = "renesas,ipmmu-r8a779f0",
+				     "renesas,rcar-gen4-ipmmu-vmsa";
+			reg = <0 0xeed00000 0 0x20000>;
+			renesas,ipmmu-main = <&ipmmu_mm 0>;
+			power-domains = <&sysc R8A779F0_PD_ALWAYS_ON>;
+			#iommu-cells = <1>;
+		};
+
+		ipmmu_hc: iommu@eed40000 {
+			compatible = "renesas,ipmmu-r8a779f0",
+				     "renesas,rcar-gen4-ipmmu-vmsa";
+			reg = <0 0xeed40000 0 0x20000>;
+			renesas,ipmmu-main = <&ipmmu_mm 2>;
+			power-domains = <&sysc R8A779F0_PD_ALWAYS_ON>;
+			#iommu-cells = <1>;
+		};
+
+		ipmmu_mm: iommu@eefc0000 {
+			compatible = "renesas,ipmmu-r8a779f0",
+				     "renesas,rcar-gen4-ipmmu-vmsa";
+			reg = <0 0xeefc0000 0 0x20000>;
+			interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
+			power-domains = <&sysc R8A779F0_PD_ALWAYS_ON>;
+			#iommu-cells = <1>;
+		};
+
+		gic: interrupt-controller@f1000000 {
+			compatible = "arm,gic-v3";
+			#interrupt-cells = <3>;
+			#address-cells = <0>;
+			interrupt-controller;
+			reg = <0x0 0xf1000000 0 0x20000>,
+			      <0x0 0xf1060000 0 0x110000>;
+			interrupts = <GIC_PPI 9
+				      (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_HIGH)>;
+		};
+
+		prr: chipid@fff00044 {
+			compatible = "renesas,prr";
+			reg = <0 0xfff00044 0 4>;
+		};
+	};
+
+	thermal-zones {
+		sensor_thermal1: sensor1-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+			thermal-sensors = <&tsc 0>;
+
+			trips {
+				sensor1_crit: sensor1-crit {
+					temperature = <120000>;
+					hysteresis = <1000>;
+					type = "critical";
+				};
+			};
+		};
+
+		sensor_thermal2: sensor2-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+			thermal-sensors = <&tsc 1>;
+
+			trips {
+				sensor2_crit: sensor2-crit {
+					temperature = <120000>;
+					hysteresis = <1000>;
+					type = "critical";
+				};
+			};
+		};
+
+		sensor_thermal3: sensor3-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+			thermal-sensors = <&tsc 2>;
+
+			trips {
+				sensor3_crit: sensor3-crit {
+					temperature = <120000>;
+					hysteresis = <1000>;
+					type = "critical";
+				};
+			};
+		};
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupts-extended = <&gic GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
+				      <&gic GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
+				      <&gic GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
+				      <&gic GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>;
+	};
+
+	ufs30_clk: ufs30-clk {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		/* This value must be overridden by the board */
+		clock-frequency = <0>;
+	};
+};
diff --git a/arch/arm64/boot/dts/renesas/r8a779g0-white-hawk-cpu.dtsi b/arch/arm64/boot/dts/renesas/r8a779g0-white-hawk-cpu.dtsi
new file mode 100644
index 000000000000..895f0bd9f754
--- /dev/null
+++ b/arch/arm64/boot/dts/renesas/r8a779g0-white-hawk-cpu.dtsi
@@ -0,0 +1,196 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+/*
+ * Device Tree Source for the White Hawk CPU board
+ *
+ * Copyright (C) 2022 Renesas Electronics Corp.
+ */
+
+#include "r8a779g0.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+	model = "Renesas White Hawk CPU board";
+	compatible = "renesas,white-hawk-cpu", "renesas,r8a779g0";
+
+	aliases {
+		ethernet0 = &avb0;
+		serial0 = &hscif0;
+	};
+
+	chosen {
+		bootargs = "ignore_loglevel rw root=/dev/nfs ip=on";
+		stdout-path = "serial0:921600n8";
+	};
+
+	keys {
+		compatible = "gpio-keys";
+
+		pinctrl-0 = <&keys_pins>;
+		pinctrl-names = "default";
+
+		key-1 {
+			gpios = <&gpio5 0 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_1>;
+			label = "SW47";
+			wakeup-source;
+			debounce-interval = <20>;
+		};
+
+		key-2 {
+			gpios = <&gpio5 1 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_2>;
+			label = "SW48";
+			wakeup-source;
+			debounce-interval = <20>;
+		};
+
+		key-3 {
+			gpios = <&gpio5 2 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_3>;
+			label = "SW49";
+			wakeup-source;
+			debounce-interval = <20>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-1 {
+			gpios = <&gpio7 0 GPIO_ACTIVE_HIGH>;
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_INDICATOR;
+			function-enumerator = <1>;
+		};
+
+		led-2 {
+			gpios = <&gpio7 1 GPIO_ACTIVE_HIGH>;
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_INDICATOR;
+			function-enumerator = <2>;
+		};
+
+		led-3 {
+			gpios = <&gpio7 2 GPIO_ACTIVE_HIGH>;
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_INDICATOR;
+			function-enumerator = <3>;
+		};
+	};
+
+	memory@48000000 {
+		device_type = "memory";
+		/* first 128MB is reserved for secure area. */
+		reg = <0x0 0x48000000 0x0 0x78000000>;
+	};
+
+	memory@480000000 {
+		device_type = "memory";
+		reg = <0x4 0x80000000 0x0 0x80000000>;
+	};
+
+	memory@600000000 {
+		device_type = "memory";
+		reg = <0x6 0x00000000 0x1 0x00000000>;
+	};
+};
+
+&avb0 {
+	pinctrl-0 = <&avb0_pins>;
+	pinctrl-names = "default";
+	phy-handle = <&phy0>;
+	tx-internal-delay-ps = <2000>;
+	status = "okay";
+
+	phy0: ethernet-phy@0 {
+		compatible = "ethernet-phy-id0022.1622",
+			     "ethernet-phy-ieee802.3-c22";
+		rxc-skew-ps = <1500>;
+		reg = <0>;
+		interrupt-parent = <&gpio7>;
+		interrupts = <5 IRQ_TYPE_LEVEL_LOW>;
+		reset-gpios = <&gpio7 10 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&extal_clk {
+	clock-frequency = <16666666>;
+};
+
+&extalr_clk {
+	clock-frequency = <32768>;
+};
+
+&hscif0 {
+	status = "okay";
+};
+
+&i2c0 {
+	pinctrl-0 = <&i2c0_pins>;
+	pinctrl-names = "default";
+
+	status = "okay";
+	clock-frequency = <400000>;
+
+	eeprom@50 {
+		compatible = "rohm,br24g01", "atmel,24c01";
+		label = "cpu-board";
+		reg = <0x50>;
+		pagesize = <8>;
+	};
+};
+
+&pfc {
+	pinctrl-0 = <&scif_clk_pins>;
+	pinctrl-names = "default";
+
+	avb0_pins: avb0 {
+		mux {
+			groups = "avb0_link", "avb0_mdio", "avb0_rgmii",
+				 "avb0_txcrefclk";
+			function = "avb0";
+		};
+
+		pins_mdio {
+			groups = "avb0_mdio";
+			drive-strength = <21>;
+		};
+
+		pins_mii {
+			groups = "avb0_rgmii";
+			drive-strength = <21>;
+		};
+
+	};
+	hscif0_pins: hscif0 {
+		groups = "hscif0_data";
+		function = "hscif0";
+	};
+
+	i2c0_pins: i2c0 {
+		groups = "i2c0";
+		function = "i2c0";
+	};
+
+	keys_pins: keys {
+		pins = "GP_5_0", "GP_5_1", "GP_5_2";
+		bias-pull-up;
+	};
+
+	scif_clk_pins: scif_clk {
+		groups = "scif_clk";
+		function = "scif_clk";
+	};
+};
+
+&scif_clk {
+	clock-frequency = <24000000>;
+};
+
+&rwdt {
+	timeout-sec = <60>;
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/renesas/r8a779g0-white-hawk-csi-dsi.dtsi b/arch/arm64/boot/dts/renesas/r8a779g0-white-hawk-csi-dsi.dtsi
new file mode 100644
index 000000000000..ae7522b60e5d
--- /dev/null
+++ b/arch/arm64/boot/dts/renesas/r8a779g0-white-hawk-csi-dsi.dtsi
@@ -0,0 +1,15 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+/*
+ * Device Tree Source for the R-Car V4H White Hawk CSI/DSI sub-board
+ *
+ * Copyright (C) 2022 Glider bv
+ */
+
+&i2c0 {
+	eeprom@52 {
+		compatible = "rohm,br24g01", "atmel,24c01";
+		label = "csi-dsi-sub-board-id";
+		reg = <0x52>;
+		pagesize = <8>;
+	};
+};
diff --git a/arch/arm64/boot/dts/renesas/r8a779g0-white-hawk-ethernet.dtsi b/arch/arm64/boot/dts/renesas/r8a779g0-white-hawk-ethernet.dtsi
new file mode 100644
index 000000000000..4f411f95c674
--- /dev/null
+++ b/arch/arm64/boot/dts/renesas/r8a779g0-white-hawk-ethernet.dtsi
@@ -0,0 +1,16 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+/*
+ * Device Tree Source for the R-Car V4H White Hawk RAVB/Ethernet(1000Base-T1)
+ * sub-board
+ *
+ * Copyright (C) 2022 Glider bv
+ */
+
+&i2c0 {
+	eeprom@53 {
+		compatible = "rohm,br24g01", "atmel,24c01";
+		label = "ethernet-sub-board-id";
+		reg = <0x53>;
+		pagesize = <8>;
+	};
+};
diff --git a/arch/arm64/boot/dts/renesas/r8a779g0-white-hawk.dts b/arch/arm64/boot/dts/renesas/r8a779g0-white-hawk.dts
new file mode 100644
index 000000000000..04a2b6b83e74
--- /dev/null
+++ b/arch/arm64/boot/dts/renesas/r8a779g0-white-hawk.dts
@@ -0,0 +1,25 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+/*
+ * Device Tree Source for the White Hawk CPU and BreakOut boards
+ *
+ * Copyright (C) 2022 Renesas Electronics Corp.
+ */
+
+/dts-v1/;
+#include "r8a779g0-white-hawk-cpu.dtsi"
+#include "r8a779g0-white-hawk-csi-dsi.dtsi"
+#include "r8a779g0-white-hawk-ethernet.dtsi"
+
+/ {
+	model = "Renesas White Hawk CPU and Breakout boards based on r8a779g0";
+	compatible = "renesas,white-hawk-breakout", "renesas,white-hawk-cpu", "renesas,r8a779g0";
+};
+
+&i2c0 {
+	eeprom@51 {
+		compatible = "rohm,br24g01", "atmel,24c01";
+		label = "breakout-board";
+		reg = <0x51>;
+		pagesize = <8>;
+	};
+};
diff --git a/arch/arm64/boot/dts/renesas/r8a779g0.dtsi b/arch/arm64/boot/dts/renesas/r8a779g0.dtsi
new file mode 100644
index 000000000000..d70f0600ae5a
--- /dev/null
+++ b/arch/arm64/boot/dts/renesas/r8a779g0.dtsi
@@ -0,0 +1,502 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+/*
+ * Device Tree Source for the R-Car V4H (R8A779G0) SoC
+ *
+ * Copyright (C) 2022 Renesas Electronics Corp.
+ */
+
+#include <dt-bindings/clock/r8a779g0-cpg-mssr.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/power/r8a779g0-sysc.h>
+
+/ {
+	compatible = "renesas,r8a779g0";
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		a76_0: cpu@0 {
+			compatible = "arm,cortex-a76";
+			reg = <0>;
+			device_type = "cpu";
+			power-domains = <&sysc R8A779G0_PD_A1E0D0C0>;
+		};
+	};
+
+	extal_clk: extal {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		/* This value must be overridden by the board */
+		clock-frequency = <0>;
+	};
+
+	extalr_clk: extalr {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		/* This value must be overridden by the board */
+		clock-frequency = <0>;
+	};
+
+	pmu_a76 {
+		compatible = "arm,cortex-a76-pmu";
+		interrupts-extended = <&gic GIC_PPI 7 IRQ_TYPE_LEVEL_LOW>;
+	};
+
+	/* External SCIF clock - to be overridden by boards that provide it */
+	scif_clk: scif {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <0>;
+	};
+
+	soc: soc {
+		compatible = "simple-bus";
+		interrupt-parent = <&gic>;
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		rwdt: watchdog@e6020000 {
+			compatible = "renesas,r8a779g0-wdt",
+				     "renesas,rcar-gen4-wdt";
+			reg = <0 0xe6020000 0 0x0c>;
+			interrupts = <GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 907>;
+			power-domains = <&sysc R8A779G0_PD_ALWAYS_ON>;
+			resets = <&cpg 907>;
+			status = "disabled";
+		};
+
+		pfc: pinctrl@e6050000 {
+			compatible = "renesas,pfc-r8a779g0";
+			reg = <0 0xe6050000 0 0x16c>, <0 0xe6050800 0 0x16c>,
+			      <0 0xe6058000 0 0x16c>, <0 0xe6058800 0 0x16c>,
+			      <0 0xe6060000 0 0x16c>, <0 0xe6060800 0 0x16c>,
+			      <0 0xe6061000 0 0x16c>, <0 0xe6061800 0 0x16c>,
+			      <0 0xe6068000 0 0x16c>;
+		};
+
+		gpio0: gpio@e6050180 {
+			compatible = "renesas,gpio-r8a779g0",
+				     "renesas,rcar-gen4-gpio";
+			reg = <0 0xe6050180 0 0x54>;
+			interrupts = <GIC_SPI 619 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 915>;
+			power-domains = <&sysc R8A779G0_PD_ALWAYS_ON>;
+			resets = <&cpg 915>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&pfc 0 0 19>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpio1: gpio@e6050980 {
+			compatible = "renesas,gpio-r8a779g0",
+				     "renesas,rcar-gen4-gpio";
+			reg = <0 0xe6050980 0 0x54>;
+			interrupts = <GIC_SPI 623 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 915>;
+			power-domains = <&sysc R8A779G0_PD_ALWAYS_ON>;
+			resets = <&cpg 915>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&pfc 0 32 29>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpio2: gpio@e6058180 {
+			compatible = "renesas,gpio-r8a779g0",
+				     "renesas,rcar-gen4-gpio";
+			reg = <0 0xe6058180 0 0x54>;
+			interrupts = <GIC_SPI 627 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 916>;
+			power-domains = <&sysc R8A779G0_PD_ALWAYS_ON>;
+			resets = <&cpg 916>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&pfc 0 64 20>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpio3: gpio@e6058980 {
+			compatible = "renesas,gpio-r8a779g0",
+				     "renesas,rcar-gen4-gpio";
+			reg = <0 0xe6058980 0 0x54>;
+			interrupts = <GIC_SPI 631 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 916>;
+			power-domains = <&sysc R8A779G0_PD_ALWAYS_ON>;
+			resets = <&cpg 916>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&pfc 0 96 30>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpio4: gpio@e6060180 {
+			compatible = "renesas,gpio-r8a779g0",
+				     "renesas,rcar-gen4-gpio";
+			reg = <0 0xe6060180 0 0x54>;
+			interrupts = <GIC_SPI 635 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 917>;
+			power-domains = <&sysc R8A779G0_PD_ALWAYS_ON>;
+			resets = <&cpg 917>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&pfc 0 128 25>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpio5: gpio@e6060980 {
+			compatible = "renesas,gpio-r8a779g0",
+				     "renesas,rcar-gen4-gpio";
+			reg = <0 0xe6060980 0 0x54>;
+			interrupts = <GIC_SPI 639 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 917>;
+			power-domains = <&sysc R8A779G0_PD_ALWAYS_ON>;
+			resets = <&cpg 917>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&pfc 0 160 21>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpio6: gpio@e6061180 {
+			compatible = "renesas,gpio-r8a779g0",
+				     "renesas,rcar-gen4-gpio";
+			reg = <0 0xe6061180 0 0x54>;
+			interrupts = <GIC_SPI 643 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 917>;
+			power-domains = <&sysc R8A779G0_PD_ALWAYS_ON>;
+			resets = <&cpg 917>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&pfc 0 192 21>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpio7: gpio@e6061980 {
+			compatible = "renesas,gpio-r8a779g0",
+				     "renesas,rcar-gen4-gpio";
+			reg = <0 0xe6061980 0 0x54>;
+			interrupts = <GIC_SPI 647 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 917>;
+			power-domains = <&sysc R8A779G0_PD_ALWAYS_ON>;
+			resets = <&cpg 917>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&pfc 0 224 21>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		gpio8: gpio@e6068180 {
+			compatible = "renesas,gpio-r8a779g0",
+				     "renesas,rcar-gen4-gpio";
+			reg = <0 0xe6068180 0 0x54>;
+			interrupts = <GIC_SPI 651 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 918>;
+			power-domains = <&sysc R8A779G0_PD_ALWAYS_ON>;
+			resets = <&cpg 918>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&pfc 0 256 14>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		cpg: clock-controller@e6150000 {
+			compatible = "renesas,r8a779g0-cpg-mssr";
+			reg = <0 0xe6150000 0 0x4000>;
+			clocks = <&extal_clk>, <&extalr_clk>;
+			clock-names = "extal", "extalr";
+			#clock-cells = <2>;
+			#power-domain-cells = <0>;
+			#reset-cells = <1>;
+		};
+
+		rst: reset-controller@e6160000 {
+			compatible = "renesas,r8a779g0-rst";
+			reg = <0 0xe6160000 0 0x4000>;
+		};
+
+		sysc: system-controller@e6180000 {
+			compatible = "renesas,r8a779g0-sysc";
+			reg = <0 0xe6180000 0 0x4000>;
+			#power-domain-cells = <1>;
+		};
+
+		i2c0: i2c@e6500000 {
+			compatible = "renesas,i2c-r8a779g0",
+				     "renesas,rcar-gen4-i2c";
+			reg = <0 0xe6500000 0 0x40>;
+			interrupts = <GIC_SPI 610 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 518>;
+			power-domains = <&sysc R8A779G0_PD_ALWAYS_ON>;
+			resets = <&cpg 518>;
+			i2c-scl-internal-delay-ns = <110>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i2c1: i2c@e6508000 {
+			compatible = "renesas,i2c-r8a779g0",
+				     "renesas,rcar-gen4-i2c";
+			reg = <0 0xe6508000 0 0x40>;
+			interrupts = <GIC_SPI 611 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 519>;
+			power-domains = <&sysc R8A779G0_PD_ALWAYS_ON>;
+			resets = <&cpg 519>;
+			i2c-scl-internal-delay-ns = <110>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i2c2: i2c@e6510000 {
+			compatible = "renesas,i2c-r8a779g0",
+				     "renesas,rcar-gen4-i2c";
+			reg = <0 0xe6510000 0 0x40>;
+			interrupts = <GIC_SPI 612 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 520>;
+			power-domains = <&sysc R8A779G0_PD_ALWAYS_ON>;
+			resets = <&cpg 520>;
+			i2c-scl-internal-delay-ns = <110>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i2c3: i2c@e66d0000 {
+			compatible = "renesas,i2c-r8a779g0",
+				     "renesas,rcar-gen4-i2c";
+			reg = <0 0xe66d0000 0 0x40>;
+			interrupts = <GIC_SPI 613 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 521>;
+			power-domains = <&sysc R8A779G0_PD_ALWAYS_ON>;
+			resets = <&cpg 521>;
+			i2c-scl-internal-delay-ns = <110>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i2c4: i2c@e66d8000 {
+			compatible = "renesas,i2c-r8a779g0",
+				     "renesas,rcar-gen4-i2c";
+			reg = <0 0xe66d8000 0 0x40>;
+			interrupts = <GIC_SPI 614 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 522>;
+			power-domains = <&sysc R8A779G0_PD_ALWAYS_ON>;
+			resets = <&cpg 522>;
+			i2c-scl-internal-delay-ns = <110>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		i2c5: i2c@e66e0000 {
+			compatible = "renesas,i2c-r8a779g0",
+				     "renesas,rcar-gen4-i2c";
+			reg = <0 0xe66e0000 0 0x40>;
+			interrupts = <GIC_SPI 615 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 523>;
+			power-domains = <&sysc R8A779G0_PD_ALWAYS_ON>;
+			resets = <&cpg 523>;
+			i2c-scl-internal-delay-ns = <110>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		hscif0: serial@e6540000 {
+			compatible = "renesas,hscif-r8a779g0",
+				     "renesas,rcar-gen4-hscif",
+				     "renesas,hscif";
+			reg = <0 0xe6540000 0 96>;
+			interrupts = <GIC_SPI 246 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD 514>,
+				 <&cpg CPG_CORE R8A779G0_CLK_S0D3_PER>,
+				 <&scif_clk>;
+			clock-names = "fck", "brg_int", "scif_clk";
+			power-domains = <&sysc R8A779G0_PD_ALWAYS_ON>;
+			resets = <&cpg 514>;
+			status = "disabled";
+		};
+
+		avb0: ethernet@e6800000 {
+			compatible = "renesas,etheravb-r8a779g0",
+				     "renesas,etheravb-rcar-gen4";
+			reg = <0 0xe6800000 0 0x800>;
+			interrupts = <GIC_SPI 335 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 336 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 337 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 338 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 339 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 340 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 341 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 342 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 343 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 344 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 345 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 346 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 347 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 348 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 349 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 350 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 351 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 352 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 359 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "ch0", "ch1", "ch2", "ch3", "ch4",
+					  "ch5", "ch6", "ch7", "ch8", "ch9",
+					  "ch10", "ch11", "ch12", "ch13",
+					  "ch14", "ch15", "ch16", "ch17",
+					  "ch18", "ch19", "ch20", "ch21",
+					  "ch22", "ch23", "ch24";
+			clocks = <&cpg CPG_MOD 211>;
+			clock-names = "fck";
+			power-domains = <&sysc R8A779G0_PD_ALWAYS_ON>;
+			resets = <&cpg 211>;
+			phy-mode = "rgmii";
+			rx-internal-delay-ps = <0>;
+			tx-internal-delay-ps = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		avb1: ethernet@e6810000 {
+			compatible = "renesas,etheravb-r8a779g0",
+				     "renesas,etheravb-rcar-gen4";
+			reg = <0 0xe6810000 0 0x800>;
+			interrupts = <GIC_SPI 360 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 361 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 362 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 363 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 364 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 365 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 366 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 367 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 368 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 369 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 370 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 371 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 372 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 373 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 374 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 375 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 376 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 377 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 378 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 379 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 380 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 381 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 382 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 383 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 384 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "ch0", "ch1", "ch2", "ch3", "ch4",
+					  "ch5", "ch6", "ch7", "ch8", "ch9",
+					  "ch10", "ch11", "ch12", "ch13",
+					  "ch14", "ch15", "ch16", "ch17",
+					  "ch18", "ch19", "ch20", "ch21",
+					  "ch22", "ch23", "ch24";
+			clocks = <&cpg CPG_MOD 212>;
+			clock-names = "fck";
+			power-domains = <&sysc R8A779G0_PD_ALWAYS_ON>;
+			resets = <&cpg 212>;
+			phy-mode = "rgmii";
+			rx-internal-delay-ps = <0>;
+			tx-internal-delay-ps = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		avb2: ethernet@e6820000 {
+			compatible = "renesas,etheravb-r8a779g0",
+				     "renesas,etheravb-rcar-gen4";
+			reg = <0 0xe6820000 0 0x1000>;
+			interrupts = <GIC_SPI 385 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 386 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 387 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 388 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 389 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 390 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 391 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 392 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 393 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 394 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 395 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 396 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 397 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 398 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 399 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 400 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 401 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 402 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 403 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 404 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 405 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 406 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 407 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 408 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 409 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "ch0", "ch1", "ch2", "ch3", "ch4",
+					  "ch5", "ch6", "ch7", "ch8", "ch9",
+					  "ch10", "ch11", "ch12", "ch13",
+					  "ch14", "ch15", "ch16", "ch17",
+					  "ch18", "ch19", "ch20", "ch21",
+					  "ch22", "ch23", "ch24";
+			clocks = <&cpg CPG_MOD 213>;
+			clock-names = "fck";
+			power-domains = <&sysc R8A779G0_PD_ALWAYS_ON>;
+			resets = <&cpg 213>;
+			phy-mode = "rgmii";
+			rx-internal-delay-ps = <0>;
+			tx-internal-delay-ps = <0>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		gic: interrupt-controller@f1000000 {
+			compatible = "arm,gic-v3";
+			#interrupt-cells = <3>;
+			#address-cells = <0>;
+			interrupt-controller;
+			reg = <0x0 0xf1000000 0 0x20000>,
+			      <0x0 0xf1060000 0 0x110000>;
+			interrupts = <GIC_PPI 9
+				      (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_HIGH)>;
+		};
+
+		prr: chipid@fff00044 {
+			compatible = "renesas,prr";
+			reg = <0 0xfff00044 0 4>;
+		};
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupts-extended = <&gic GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
+				      <&gic GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
+				      <&gic GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
+				      <&gic GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>;
+	};
+};
diff --git a/arch/arm64/boot/dts/renesas/r8a779m8.dtsi b/arch/arm64/boot/dts/renesas/r8a779m8.dtsi
index 752440b0c40f..750bd8ccdb7f 100644
--- a/arch/arm64/boot/dts/renesas/r8a779m8.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a779m8.dtsi
@@ -10,3 +10,8 @@
 / {
 	compatible = "renesas,r8a779m8", "renesas,r8a7795";
 };
+
+&cluster0_opp {
+	/delete-node/ opp-1600000000;
+	/delete-node/ opp-1700000000;
+};
diff --git a/arch/arm64/boot/dts/renesas/r8a779mb.dtsi b/arch/arm64/boot/dts/renesas/r8a779mb.dtsi
new file mode 100644
index 000000000000..40d1dce2f350
--- /dev/null
+++ b/arch/arm64/boot/dts/renesas/r8a779mb.dtsi
@@ -0,0 +1,12 @@
+// SPDX-License-Identifier: (GPL-2.0 or MIT)
+/*
+ * Device Tree Source for the R-Car H3Ne-1.7G (R8A779MB) SoC
+ *
+ * Copyright (C) 2022 Glider bv
+ */
+
+#include "r8a77951.dtsi"
+
+/ {
+	compatible = "renesas,r8a779mb", "renesas,r8a7795";
+};
diff --git a/arch/arm64/boot/dts/renesas/r9a07g043.dtsi b/arch/arm64/boot/dts/renesas/r9a07g043.dtsi
new file mode 100644
index 000000000000..689aa4ba416b
--- /dev/null
+++ b/arch/arm64/boot/dts/renesas/r9a07g043.dtsi
@@ -0,0 +1,910 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+/*
+ * Device Tree Source for the RZ/G2UL SoC
+ *
+ * Copyright (C) 2022 Renesas Electronics Corp.
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/r9a07g043-cpg.h>
+
+/ {
+	compatible = "renesas,r9a07g043";
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	audio_clk1: audio1-clk {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		/* This value must be overridden by boards that provide it */
+		clock-frequency = <0>;
+	};
+
+	audio_clk2: audio2-clk {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		/* This value must be overridden by boards that provide it */
+		clock-frequency = <0>;
+	};
+
+	/* External CAN clock - to be overridden by boards that provide it */
+	can_clk: can-clk {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <0>;
+	};
+
+	/* clock can be either from exclk or crystal oscillator (XIN/XOUT) */
+	extal_clk: extal-clk {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		/* This value must be overridden by the board */
+		clock-frequency = <0>;
+	};
+
+	cluster0_opp: opp-table-0 {
+		compatible = "operating-points-v2";
+		opp-shared;
+
+		opp-125000000 {
+			opp-hz = /bits/ 64 <125000000>;
+			opp-microvolt = <1100000>;
+			clock-latency-ns = <300000>;
+		};
+		opp-250000000 {
+			opp-hz = /bits/ 64 <250000000>;
+			opp-microvolt = <1100000>;
+			clock-latency-ns = <300000>;
+		};
+		opp-500000000 {
+			opp-hz = /bits/ 64 <500000000>;
+			opp-microvolt = <1100000>;
+			clock-latency-ns = <300000>;
+		};
+		opp-1000000000 {
+			opp-hz = /bits/ 64 <1000000000>;
+			opp-microvolt = <1100000>;
+			clock-latency-ns = <300000>;
+			opp-suspend;
+		};
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			compatible = "arm,cortex-a55";
+			reg = <0>;
+			device_type = "cpu";
+			#cooling-cells = <2>;
+			next-level-cache = <&L3_CA55>;
+			enable-method = "psci";
+			clocks = <&cpg CPG_CORE R9A07G043_CLK_I>;
+			operating-points-v2 = <&cluster0_opp>;
+		};
+
+		L3_CA55: cache-controller-0 {
+			compatible = "cache";
+			cache-unified;
+			cache-size = <0x40000>;
+		};
+	};
+
+	psci {
+		compatible = "arm,psci-1.0", "arm,psci-0.2";
+		method = "smc";
+	};
+
+	soc: soc {
+		compatible = "simple-bus";
+		interrupt-parent = <&gic>;
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		ssi0: ssi@10049c00 {
+			compatible = "renesas,r9a07g043-ssi",
+				     "renesas,rz-ssi";
+			reg = <0 0x10049c00 0 0x400>;
+			interrupts = <GIC_SPI 326 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 327 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 328 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 329 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "int_req", "dma_rx", "dma_tx", "dma_rt";
+			clocks = <&cpg CPG_MOD R9A07G043_SSI0_PCLK2>,
+				 <&cpg CPG_MOD R9A07G043_SSI0_PCLK_SFR>,
+				 <&audio_clk1>, <&audio_clk2>;
+			clock-names = "ssi", "ssi_sfr", "audio_clk1", "audio_clk2";
+			resets = <&cpg R9A07G043_SSI0_RST_M2_REG>;
+			dmas = <&dmac 0x2655>, <&dmac 0x2656>;
+			dma-names = "tx", "rx";
+			power-domains = <&cpg>;
+			#sound-dai-cells = <0>;
+			status = "disabled";
+		};
+
+		ssi1: ssi@1004a000 {
+			compatible = "renesas,r9a07g043-ssi",
+				     "renesas,rz-ssi";
+			reg = <0 0x1004a000 0 0x400>;
+			interrupts = <GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 331 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 332 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 333 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "int_req", "dma_rx", "dma_tx", "dma_rt";
+			clocks = <&cpg CPG_MOD R9A07G043_SSI1_PCLK2>,
+				 <&cpg CPG_MOD R9A07G043_SSI1_PCLK_SFR>,
+				 <&audio_clk1>, <&audio_clk2>;
+			clock-names = "ssi", "ssi_sfr", "audio_clk1", "audio_clk2";
+			resets = <&cpg R9A07G043_SSI1_RST_M2_REG>;
+			dmas = <&dmac 0x2659>, <&dmac 0x265a>;
+			dma-names = "tx", "rx";
+			power-domains = <&cpg>;
+			#sound-dai-cells = <0>;
+			status = "disabled";
+		};
+
+		ssi2: ssi@1004a400 {
+			compatible = "renesas,r9a07g043-ssi",
+				     "renesas,rz-ssi";
+			reg = <0 0x1004a400 0 0x400>;
+			interrupts = <GIC_SPI 334 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 335 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 336 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 337 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "int_req", "dma_rx", "dma_tx", "dma_rt";
+			clocks = <&cpg CPG_MOD R9A07G043_SSI2_PCLK2>,
+				 <&cpg CPG_MOD R9A07G043_SSI2_PCLK_SFR>,
+				 <&audio_clk1>, <&audio_clk2>;
+			clock-names = "ssi", "ssi_sfr", "audio_clk1", "audio_clk2";
+			resets = <&cpg R9A07G043_SSI2_RST_M2_REG>;
+			dmas = <&dmac 0x265f>;
+			dma-names = "rt";
+			power-domains = <&cpg>;
+			#sound-dai-cells = <0>;
+			status = "disabled";
+		};
+
+		ssi3: ssi@1004a800 {
+			compatible = "renesas,r9a07g043-ssi",
+				     "renesas,rz-ssi";
+			reg = <0 0x1004a800 0 0x400>;
+			interrupts = <GIC_SPI 338 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 339 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 340 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 341 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "int_req", "dma_rx", "dma_tx", "dma_rt";
+			clocks = <&cpg CPG_MOD R9A07G043_SSI3_PCLK2>,
+				 <&cpg CPG_MOD R9A07G043_SSI3_PCLK_SFR>,
+				 <&audio_clk1>, <&audio_clk2>;
+			clock-names = "ssi", "ssi_sfr", "audio_clk1", "audio_clk2";
+			resets = <&cpg R9A07G043_SSI3_RST_M2_REG>;
+			dmas = <&dmac 0x2661>, <&dmac 0x2662>;
+			dma-names = "tx", "rx";
+			power-domains = <&cpg>;
+			#sound-dai-cells = <0>;
+			status = "disabled";
+		};
+
+		spi0: spi@1004ac00 {
+			compatible = "renesas,r9a07g043-rspi", "renesas,rspi-rz";
+			reg = <0 0x1004ac00 0 0x400>;
+			interrupts = <GIC_SPI 415 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 413 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 414 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "error", "rx", "tx";
+			clocks = <&cpg CPG_MOD R9A07G043_RSPI0_CLKB>;
+			resets = <&cpg R9A07G043_RSPI0_RST>;
+			dmas = <&dmac 0x2e95>, <&dmac 0x2e96>;
+			dma-names = "tx", "rx";
+			power-domains = <&cpg>;
+			num-cs = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		spi1: spi@1004b000 {
+			compatible = "renesas,r9a07g043-rspi", "renesas,rspi-rz";
+			reg = <0 0x1004b000 0 0x400>;
+			interrupts = <GIC_SPI 418 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 416 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 417 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "error", "rx", "tx";
+			clocks = <&cpg CPG_MOD R9A07G043_RSPI1_CLKB>;
+			resets = <&cpg R9A07G043_RSPI1_RST>;
+			dmas = <&dmac 0x2e99>, <&dmac 0x2e9a>;
+			dma-names = "tx", "rx";
+			power-domains = <&cpg>;
+			num-cs = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		spi2: spi@1004b400 {
+			compatible = "renesas,r9a07g043-rspi", "renesas,rspi-rz";
+			reg = <0 0x1004b400 0 0x400>;
+			interrupts = <GIC_SPI 421 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 419 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 420 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "error", "rx", "tx";
+			clocks = <&cpg CPG_MOD R9A07G043_RSPI2_CLKB>;
+			resets = <&cpg R9A07G043_RSPI2_RST>;
+			dmas = <&dmac 0x2e9d>, <&dmac 0x2e9e>;
+			dma-names = "tx", "rx";
+			power-domains = <&cpg>;
+			num-cs = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		scif0: serial@1004b800 {
+			compatible = "renesas,scif-r9a07g043",
+				     "renesas,scif-r9a07g044";
+			reg = <0 0x1004b800 0 0x400>;
+			interrupts = <GIC_SPI 380 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 382 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 383 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 381 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 384 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 384 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "eri", "rxi", "txi",
+					  "bri", "dri", "tei";
+			clocks = <&cpg CPG_MOD R9A07G043_SCIF0_CLK_PCK>;
+			clock-names = "fck";
+			power-domains = <&cpg>;
+			resets = <&cpg R9A07G043_SCIF0_RST_SYSTEM_N>;
+			status = "disabled";
+		};
+
+		scif1: serial@1004bc00 {
+			compatible = "renesas,scif-r9a07g043",
+				     "renesas,scif-r9a07g044";
+			reg = <0 0x1004bc00 0 0x400>;
+			interrupts = <GIC_SPI 385 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 387 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 388 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 386 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 389 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 389 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "eri", "rxi", "txi",
+					  "bri", "dri", "tei";
+			clocks = <&cpg CPG_MOD R9A07G043_SCIF1_CLK_PCK>;
+			clock-names = "fck";
+			power-domains = <&cpg>;
+			resets = <&cpg R9A07G043_SCIF1_RST_SYSTEM_N>;
+			status = "disabled";
+		};
+
+		scif2: serial@1004c000 {
+			compatible = "renesas,scif-r9a07g043",
+				     "renesas,scif-r9a07g044";
+			reg = <0 0x1004c000 0 0x400>;
+			interrupts = <GIC_SPI 390 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 392 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 393 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 391 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 394 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 394 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "eri", "rxi", "txi",
+					  "bri", "dri", "tei";
+			clocks = <&cpg CPG_MOD R9A07G043_SCIF2_CLK_PCK>;
+			clock-names = "fck";
+			power-domains = <&cpg>;
+			resets = <&cpg R9A07G043_SCIF2_RST_SYSTEM_N>;
+			status = "disabled";
+		};
+
+		scif3: serial@1004c400 {
+			compatible = "renesas,scif-r9a07g043",
+				     "renesas,scif-r9a07g044";
+			reg = <0 0x1004c400 0 0x400>;
+			interrupts = <GIC_SPI 395 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 397 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 398 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 396 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 399 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 399 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "eri", "rxi", "txi",
+					  "bri", "dri", "tei";
+			clocks = <&cpg CPG_MOD R9A07G043_SCIF3_CLK_PCK>;
+			clock-names = "fck";
+			power-domains = <&cpg>;
+			resets = <&cpg R9A07G043_SCIF3_RST_SYSTEM_N>;
+			status = "disabled";
+		};
+
+		scif4: serial@1004c800 {
+			compatible = "renesas,scif-r9a07g043",
+				     "renesas,scif-r9a07g044";
+			reg = <0 0x1004c800 0 0x400>;
+			interrupts = <GIC_SPI 400 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 402 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 403 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 401 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 404 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 404 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "eri", "rxi", "txi",
+					  "bri", "dri", "tei";
+			clocks = <&cpg CPG_MOD R9A07G043_SCIF4_CLK_PCK>;
+			clock-names = "fck";
+			power-domains = <&cpg>;
+			resets = <&cpg R9A07G043_SCIF4_RST_SYSTEM_N>;
+			status = "disabled";
+		};
+
+		sci0: serial@1004d000 {
+			compatible = "renesas,r9a07g043-sci", "renesas,sci";
+			reg = <0 0x1004d000 0 0x400>;
+			interrupts = <GIC_SPI 405 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 406 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 407 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 408 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "eri", "rxi", "txi", "tei";
+			clocks = <&cpg CPG_MOD R9A07G043_SCI0_CLKP>;
+			clock-names = "fck";
+			power-domains = <&cpg>;
+			resets = <&cpg R9A07G043_SCI0_RST>;
+			status = "disabled";
+		};
+
+		sci1: serial@1004d400 {
+			compatible = "renesas,r9a07g043-sci", "renesas,sci";
+			reg = <0 0x1004d400 0 0x400>;
+			interrupts = <GIC_SPI 409 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 410 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 411 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 412 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "eri", "rxi", "txi", "tei";
+			clocks = <&cpg CPG_MOD R9A07G043_SCI1_CLKP>;
+			clock-names = "fck";
+			power-domains = <&cpg>;
+			resets = <&cpg R9A07G043_SCI1_RST>;
+			status = "disabled";
+		};
+
+		canfd: can@10050000 {
+			compatible = "renesas,r9a07g043-canfd", "renesas,rzg2l-canfd";
+			reg = <0 0x10050000 0 0x8000>;
+			interrupts = <GIC_SPI 426 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 427 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 422 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 424 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 428 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 423 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 425 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 429 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "g_err", "g_recc",
+					  "ch0_err", "ch0_rec", "ch0_trx",
+					  "ch1_err", "ch1_rec", "ch1_trx";
+			clocks = <&cpg CPG_MOD R9A07G043_CANFD_PCLK>,
+				 <&cpg CPG_CORE R9A07G043_CLK_P0_DIV2>,
+				 <&can_clk>;
+			clock-names = "fck", "canfd", "can_clk";
+			assigned-clocks = <&cpg CPG_CORE R9A07G043_CLK_P0_DIV2>;
+			assigned-clock-rates = <50000000>;
+			resets = <&cpg R9A07G043_CANFD_RSTP_N>,
+				 <&cpg R9A07G043_CANFD_RSTC_N>;
+			reset-names = "rstp_n", "rstc_n";
+			power-domains = <&cpg>;
+			status = "disabled";
+
+			channel0 {
+				status = "disabled";
+			};
+			channel1 {
+				status = "disabled";
+			};
+		};
+
+		i2c0: i2c@10058000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "renesas,riic-r9a07g043", "renesas,riic-rz";
+			reg = <0 0x10058000 0 0x400>;
+			interrupts = <GIC_SPI 350 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 348 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 349 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 352 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 351 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "tei", "ri", "ti", "spi", "sti",
+					  "naki", "ali", "tmoi";
+			clocks = <&cpg CPG_MOD R9A07G043_I2C0_PCLK>;
+			clock-frequency = <100000>;
+			resets = <&cpg R9A07G043_I2C0_MRST>;
+			power-domains = <&cpg>;
+			status = "disabled";
+		};
+
+		i2c1: i2c@10058400 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "renesas,riic-r9a07g043", "renesas,riic-rz";
+			reg = <0 0x10058400 0 0x400>;
+			interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 356 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 357 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 360 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 361 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 359 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 362 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 363 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "tei", "ri", "ti", "spi", "sti",
+					  "naki", "ali", "tmoi";
+			clocks = <&cpg CPG_MOD R9A07G043_I2C1_PCLK>;
+			clock-frequency = <100000>;
+			resets = <&cpg R9A07G043_I2C1_MRST>;
+			power-domains = <&cpg>;
+			status = "disabled";
+		};
+
+		i2c2: i2c@10058800 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "renesas,riic-r9a07g043", "renesas,riic-rz";
+			reg = <0 0x10058800 0 0x400>;
+			interrupts = <GIC_SPI 366 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 364 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 365 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 368 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 369 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 367 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 370 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 371 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "tei", "ri", "ti", "spi", "sti",
+					  "naki", "ali", "tmoi";
+			clocks = <&cpg CPG_MOD R9A07G043_I2C2_PCLK>;
+			clock-frequency = <100000>;
+			resets = <&cpg R9A07G043_I2C2_MRST>;
+			power-domains = <&cpg>;
+			status = "disabled";
+		};
+
+		i2c3: i2c@10058c00 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "renesas,riic-r9a07g043", "renesas,riic-rz";
+			reg = <0 0x10058c00 0 0x400>;
+			interrupts = <GIC_SPI 374 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 372 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 373 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 376 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 377 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 375 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 378 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 379 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "tei", "ri", "ti", "spi", "sti",
+					  "naki", "ali", "tmoi";
+			clocks = <&cpg CPG_MOD R9A07G043_I2C3_PCLK>;
+			clock-frequency = <100000>;
+			resets = <&cpg R9A07G043_I2C3_MRST>;
+			power-domains = <&cpg>;
+			status = "disabled";
+		};
+
+		adc: adc@10059000 {
+			compatible = "renesas,r9a07g043-adc", "renesas,rzg2l-adc";
+			reg = <0 0x10059000 0 0x400>;
+			interrupts = <GIC_SPI 347 IRQ_TYPE_EDGE_RISING>;
+			clocks = <&cpg CPG_MOD R9A07G043_ADC_ADCLK>,
+				 <&cpg CPG_MOD R9A07G043_ADC_PCLK>;
+			clock-names = "adclk", "pclk";
+			resets = <&cpg R9A07G043_ADC_PRESETN>,
+				 <&cpg R9A07G043_ADC_ADRST_N>;
+			reset-names = "presetn", "adrst-n";
+			power-domains = <&cpg>;
+			status = "disabled";
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			channel@0 {
+				reg = <0>;
+			};
+			channel@1 {
+				reg = <1>;
+			};
+		};
+
+		tsu: thermal@10059400 {
+			compatible = "renesas,r9a07g043-tsu",
+				     "renesas,rzg2l-tsu";
+			reg = <0 0x10059400 0 0x400>;
+			clocks = <&cpg CPG_MOD R9A07G043_TSU_PCLK>;
+			resets = <&cpg R9A07G043_TSU_PRESETN>;
+			power-domains = <&cpg>;
+			#thermal-sensor-cells = <1>;
+		};
+
+		sbc: spi@10060000 {
+			compatible = "renesas,r9a07g043-rpc-if",
+				     "renesas,rzg2l-rpc-if";
+			reg = <0 0x10060000 0 0x10000>,
+			      <0 0x20000000 0 0x10000000>,
+			      <0 0x10070000 0 0x10000>;
+			reg-names = "regs", "dirmap", "wbuf";
+			clocks = <&cpg CPG_MOD R9A07G043_SPI_CLK2>,
+				 <&cpg CPG_MOD R9A07G043_SPI_CLK>;
+			resets = <&cpg R9A07G043_SPI_RST>;
+			power-domains = <&cpg>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		cpg: clock-controller@11010000 {
+			compatible = "renesas,r9a07g043-cpg";
+			reg = <0 0x11010000 0 0x10000>;
+			clocks = <&extal_clk>;
+			clock-names = "extal";
+			#clock-cells = <2>;
+			#reset-cells = <1>;
+			#power-domain-cells = <0>;
+		};
+
+		sysc: system-controller@11020000 {
+			compatible = "renesas,r9a07g043-sysc";
+			reg = <0 0x11020000 0 0x10000>;
+			interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "lpm_int", "ca55stbydone_int",
+					  "cm33stbyr_int", "ca55_deny";
+			status = "disabled";
+		};
+
+		pinctrl: pinctrl@11030000 {
+			compatible = "renesas,r9a07g043-pinctrl";
+			reg = <0 0x11030000 0 0x10000>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&pinctrl 0 0 152>;
+			clocks = <&cpg CPG_MOD R9A07G043_GPIO_HCLK>;
+			power-domains = <&cpg>;
+			resets = <&cpg R9A07G043_GPIO_RSTN>,
+				 <&cpg R9A07G043_GPIO_PORT_RESETN>,
+				 <&cpg R9A07G043_GPIO_SPARE_RESETN>;
+		};
+
+		dmac: dma-controller@11820000 {
+			compatible = "renesas,r9a07g043-dmac",
+				     "renesas,rz-dmac";
+			reg = <0 0x11820000 0 0x10000>,
+			      <0 0x11830000 0 0x10000>;
+			interrupts = <GIC_SPI 141 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 125 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 126 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 127 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 128 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 129 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 130 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 131 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 132 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 133 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 134 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 135 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 136 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 137 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 138 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 139 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 140 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "error",
+					  "ch0", "ch1", "ch2", "ch3",
+					  "ch4", "ch5", "ch6", "ch7",
+					  "ch8", "ch9", "ch10", "ch11",
+					  "ch12", "ch13", "ch14", "ch15";
+			clocks = <&cpg CPG_MOD R9A07G043_DMAC_ACLK>,
+				 <&cpg CPG_MOD R9A07G043_DMAC_PCLK>;
+			power-domains = <&cpg>;
+			resets = <&cpg R9A07G043_DMAC_ARESETN>,
+				 <&cpg R9A07G043_DMAC_RST_ASYNC>;
+			#dma-cells = <1>;
+			dma-channels = <16>;
+		};
+
+		gic: interrupt-controller@11900000 {
+			compatible = "arm,gic-v3";
+			#interrupt-cells = <3>;
+			#address-cells = <0>;
+			interrupt-controller;
+			reg = <0x0 0x11900000 0 0x40000>,
+			      <0x0 0x11940000 0 0x60000>;
+			interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_LOW>;
+		};
+
+		sdhi0: mmc@11c00000 {
+			compatible = "renesas,sdhi-r9a07g043",
+				     "renesas,rcar-gen3-sdhi";
+			reg = <0x0 0x11c00000 0 0x10000>;
+			interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD R9A07G043_SDHI0_IMCLK>,
+				 <&cpg CPG_MOD R9A07G043_SDHI0_CLK_HS>,
+				 <&cpg CPG_MOD R9A07G043_SDHI0_IMCLK2>,
+				 <&cpg CPG_MOD R9A07G043_SDHI0_ACLK>;
+			clock-names = "core", "clkh", "cd", "aclk";
+			resets = <&cpg R9A07G043_SDHI0_IXRST>;
+			power-domains = <&cpg>;
+			status = "disabled";
+		};
+
+		sdhi1: mmc@11c10000 {
+			compatible = "renesas,sdhi-r9a07g043",
+				     "renesas,rcar-gen3-sdhi";
+			reg = <0x0 0x11c10000 0 0x10000>;
+			interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD R9A07G043_SDHI1_IMCLK>,
+				 <&cpg CPG_MOD R9A07G043_SDHI1_CLK_HS>,
+				 <&cpg CPG_MOD R9A07G043_SDHI1_IMCLK2>,
+				 <&cpg CPG_MOD R9A07G043_SDHI1_ACLK>;
+			clock-names = "core", "clkh", "cd", "aclk";
+			resets = <&cpg R9A07G043_SDHI1_IXRST>;
+			power-domains = <&cpg>;
+			status = "disabled";
+		};
+
+		eth0: ethernet@11c20000 {
+			compatible = "renesas,r9a07g043-gbeth",
+				     "renesas,rzg2l-gbeth";
+			reg = <0 0x11c20000 0 0x10000>;
+			interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "mux", "fil", "arp_ns";
+			phy-mode = "rgmii";
+			clocks = <&cpg CPG_MOD R9A07G043_ETH0_CLK_AXI>,
+				 <&cpg CPG_MOD R9A07G043_ETH0_CLK_CHI>,
+				 <&cpg CPG_CORE R9A07G043_CLK_HP>;
+			clock-names = "axi", "chi", "refclk";
+			resets = <&cpg R9A07G043_ETH0_RST_HW_N>;
+			power-domains = <&cpg>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		eth1: ethernet@11c30000 {
+			compatible = "renesas,r9a07g043-gbeth",
+				     "renesas,rzg2l-gbeth";
+			reg = <0 0x11c30000 0 0x10000>;
+			interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "mux", "fil", "arp_ns";
+			phy-mode = "rgmii";
+			clocks = <&cpg CPG_MOD R9A07G043_ETH1_CLK_AXI>,
+				 <&cpg CPG_MOD R9A07G043_ETH1_CLK_CHI>,
+				 <&cpg CPG_CORE R9A07G043_CLK_HP>;
+			clock-names = "axi", "chi", "refclk";
+			resets = <&cpg R9A07G043_ETH1_RST_HW_N>;
+			power-domains = <&cpg>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		phyrst: usbphy-ctrl@11c40000 {
+			compatible = "renesas,r9a07g043-usbphy-ctrl",
+				     "renesas,rzg2l-usbphy-ctrl";
+			reg = <0 0x11c40000 0 0x10000>;
+			clocks = <&cpg CPG_MOD R9A07G043_USB_PCLK>;
+			resets = <&cpg R9A07G043_USB_PRESETN>;
+			power-domains = <&cpg>;
+			#reset-cells = <1>;
+			status = "disabled";
+		};
+
+		ohci0: usb@11c50000 {
+			compatible = "generic-ohci";
+			reg = <0 0x11c50000 0 0x100>;
+			interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD R9A07G043_USB_PCLK>,
+				 <&cpg CPG_MOD R9A07G043_USB_U2H0_HCLK>;
+			resets = <&phyrst 0>,
+				 <&cpg R9A07G043_USB_U2H0_HRESETN>;
+			phys = <&usb2_phy0 1>;
+			phy-names = "usb";
+			power-domains = <&cpg>;
+			status = "disabled";
+		};
+
+		ohci1: usb@11c70000 {
+			compatible = "generic-ohci";
+			reg = <0 0x11c70000 0 0x100>;
+			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD R9A07G043_USB_PCLK>,
+				 <&cpg CPG_MOD R9A07G043_USB_U2H1_HCLK>;
+			resets = <&phyrst 1>,
+				 <&cpg R9A07G043_USB_U2H1_HRESETN>;
+			phys = <&usb2_phy1 1>;
+			phy-names = "usb";
+			power-domains = <&cpg>;
+			status = "disabled";
+		};
+
+		ehci0: usb@11c50100 {
+			compatible = "generic-ehci";
+			reg = <0 0x11c50100 0 0x100>;
+			interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD R9A07G043_USB_PCLK>,
+				 <&cpg CPG_MOD R9A07G043_USB_U2H0_HCLK>;
+			resets = <&phyrst 0>,
+				 <&cpg R9A07G043_USB_U2H0_HRESETN>;
+			phys = <&usb2_phy0 2>;
+			phy-names = "usb";
+			companion = <&ohci0>;
+			power-domains = <&cpg>;
+			status = "disabled";
+		};
+
+		ehci1: usb@11c70100 {
+			compatible = "generic-ehci";
+			reg = <0 0x11c70100 0 0x100>;
+			interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD R9A07G043_USB_PCLK>,
+				 <&cpg CPG_MOD R9A07G043_USB_U2H1_HCLK>;
+			resets = <&phyrst 1>,
+				 <&cpg R9A07G043_USB_U2H1_HRESETN>;
+			phys = <&usb2_phy1 2>;
+			phy-names = "usb";
+			companion = <&ohci1>;
+			power-domains = <&cpg>;
+			status = "disabled";
+		};
+
+		usb2_phy0: usb-phy@11c50200 {
+			compatible = "renesas,usb2-phy-r9a07g043",
+				     "renesas,rzg2l-usb2-phy";
+			reg = <0 0x11c50200 0 0x700>;
+			interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD R9A07G043_USB_PCLK>,
+				 <&cpg CPG_MOD R9A07G043_USB_U2H0_HCLK>;
+			resets = <&phyrst 0>;
+			#phy-cells = <1>;
+			power-domains = <&cpg>;
+			status = "disabled";
+		};
+
+		usb2_phy1: usb-phy@11c70200 {
+			compatible = "renesas,usb2-phy-r9a07g043",
+				     "renesas,rzg2l-usb2-phy";
+			reg = <0 0x11c70200 0 0x700>;
+			interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD R9A07G043_USB_PCLK>,
+				 <&cpg CPG_MOD R9A07G043_USB_U2H1_HCLK>;
+			resets = <&phyrst 1>;
+			#phy-cells = <1>;
+			power-domains = <&cpg>;
+			status = "disabled";
+		};
+
+		hsusb: usb@11c60000 {
+			compatible = "renesas,usbhs-r9a07g043",
+				     "renesas,rza2-usbhs";
+			reg = <0 0x11c60000 0 0x10000>;
+			interrupts = <GIC_SPI 100 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD R9A07G043_USB_PCLK>,
+				 <&cpg CPG_MOD R9A07G043_USB_U2P_EXR_CPUCLK>;
+			resets = <&phyrst 0>,
+				 <&cpg R9A07G043_USB_U2P_EXL_SYSRST>;
+			renesas,buswait = <7>;
+			phys = <&usb2_phy0 3>;
+			phy-names = "usb";
+			power-domains = <&cpg>;
+			status = "disabled";
+		};
+
+		wdt0: watchdog@12800800 {
+			compatible = "renesas,r9a07g043-wdt",
+				     "renesas,rzg2l-wdt";
+			reg = <0 0x12800800 0 0x400>;
+			clocks = <&cpg CPG_MOD R9A07G043_WDT0_PCLK>,
+				 <&cpg CPG_MOD R9A07G043_WDT0_CLK>;
+			clock-names = "pclk", "oscclk";
+			interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "wdt", "perrout";
+			resets = <&cpg R9A07G043_WDT0_PRESETN>;
+			power-domains = <&cpg>;
+			status = "disabled";
+		};
+
+		wdt2: watchdog@12800400 {
+			compatible = "renesas,r9a07g043-wdt",
+				     "renesas,rzg2l-wdt";
+			reg = <0 0x12800400 0 0x400>;
+			clocks = <&cpg CPG_MOD R9A07G043_WDT2_PCLK>,
+				 <&cpg CPG_MOD R9A07G043_WDT2_CLK>;
+			clock-names = "pclk", "oscclk";
+			interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "wdt", "perrout";
+			resets = <&cpg R9A07G043_WDT2_PRESETN>;
+			power-domains = <&cpg>;
+			status = "disabled";
+		};
+
+		ostm0: timer@12801000 {
+			compatible = "renesas,r9a07g043-ostm",
+				     "renesas,ostm";
+			reg = <0x0 0x12801000 0x0 0x400>;
+			interrupts = <GIC_SPI 46 IRQ_TYPE_EDGE_RISING>;
+			clocks = <&cpg CPG_MOD R9A07G043_OSTM0_PCLK>;
+			resets = <&cpg R9A07G043_OSTM0_PRESETZ>;
+			power-domains = <&cpg>;
+			status = "disabled";
+		};
+
+		ostm1: timer@12801400 {
+			compatible = "renesas,r9a07g043-ostm",
+				     "renesas,ostm";
+			reg = <0x0 0x12801400 0x0 0x400>;
+			interrupts = <GIC_SPI 47 IRQ_TYPE_EDGE_RISING>;
+			clocks = <&cpg CPG_MOD R9A07G043_OSTM1_PCLK>;
+			resets = <&cpg R9A07G043_OSTM1_PRESETZ>;
+			power-domains = <&cpg>;
+			status = "disabled";
+		};
+
+		ostm2: timer@12801800 {
+			compatible = "renesas,r9a07g043-ostm",
+				     "renesas,ostm";
+			reg = <0x0 0x12801800 0x0 0x400>;
+			interrupts = <GIC_SPI 48 IRQ_TYPE_EDGE_RISING>;
+			clocks = <&cpg CPG_MOD R9A07G043_OSTM2_PCLK>;
+			resets = <&cpg R9A07G043_OSTM2_PRESETZ>;
+			power-domains = <&cpg>;
+			status = "disabled";
+		};
+	};
+
+	thermal-zones {
+		cpu-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+			thermal-sensors = <&tsu 0>;
+			sustainable-power = <717>;
+
+			cooling-maps {
+				map0 {
+					trip = <&target>;
+					cooling-device = <&cpu0 0 2>;
+					contribution = <1024>;
+				};
+			};
+
+			trips {
+				sensor_crit: sensor-crit {
+					temperature = <125000>;
+					hysteresis = <1000>;
+					type = "critical";
+				};
+
+				target: trip-point {
+					temperature = <100000>;
+					hysteresis = <1000>;
+					type = "passive";
+				};
+			};
+		};
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupts-extended = <&gic GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
+				      <&gic GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
+				      <&gic GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
+				      <&gic GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>;
+	};
+};
diff --git a/arch/arm64/boot/dts/renesas/r9a07g043u11-smarc.dts b/arch/arm64/boot/dts/renesas/r9a07g043u11-smarc.dts
new file mode 100644
index 000000000000..059885a01ede
--- /dev/null
+++ b/arch/arm64/boot/dts/renesas/r9a07g043u11-smarc.dts
@@ -0,0 +1,27 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+/*
+ * Device Tree Source for the RZ/G2UL Type-1 SMARC EVK board
+ *
+ * Copyright (C) 2022 Renesas Electronics Corp.
+ */
+
+/dts-v1/;
+
+/*
+ * DIP-Switch SW1 setting
+ * 1 : High; 0: Low
+ * SW1-2 : SW_SD0_DEV_SEL	(0: uSD; 1: eMMC)
+ * SW1-3 : SW_ET0_EN_N		(0: ETHER0; 1: CAN0, CAN1, SSI1, RSPI1)
+ * Please change below macros according to SW1 setting on the SoM
+ */
+#define SW_SW0_DEV_SEL	1
+#define SW_ET0_EN_N	1
+
+#include "r9a07g043.dtsi"
+#include "rzg2ul-smarc-som.dtsi"
+#include "rzg2ul-smarc.dtsi"
+
+/ {
+	model = "Renesas SMARC EVK based on r9a07g043u11";
+	compatible = "renesas,smarc-evk", "renesas,r9a07g043u11", "renesas,r9a07g043";
+};
diff --git a/arch/arm64/boot/dts/renesas/r9a07g044.dtsi b/arch/arm64/boot/dts/renesas/r9a07g044.dtsi
index 485ef5f0fea1..2283d4fb8736 100644
--- a/arch/arm64/boot/dts/renesas/r9a07g044.dtsi
+++ b/arch/arm64/boot/dts/renesas/r9a07g044.dtsi
@@ -13,14 +13,14 @@
 	#address-cells = <2>;
 	#size-cells = <2>;
 
-	audio_clk1: audio_clk1 {
+	audio_clk1: audio1-clk {
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
 		/* This value must be overridden by boards that provide it */
 		clock-frequency = <0>;
 	};
 
-	audio_clk2: audio_clk2 {
+	audio_clk2: audio2-clk {
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
 		/* This value must be overridden by boards that provide it */
@@ -28,23 +28,45 @@
 	};
 
 	/* External CAN clock - to be overridden by boards that provide it */
-	can_clk: can {
+	can_clk: can-clk {
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
 		clock-frequency = <0>;
 	};
 
 	/* clock can be either from exclk or crystal oscillator (XIN/XOUT) */
-	extal_clk: extal {
+	extal_clk: extal-clk {
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
 		/* This value must be overridden by the board */
 		clock-frequency = <0>;
 	};
 
-	psci {
-		compatible = "arm,psci-1.0", "arm,psci-0.2";
-		method = "smc";
+	cluster0_opp: opp-table-0 {
+		compatible = "operating-points-v2";
+		opp-shared;
+
+		opp-150000000 {
+			opp-hz = /bits/ 64 <150000000>;
+			opp-microvolt = <1100000>;
+			clock-latency-ns = <300000>;
+		};
+		opp-300000000 {
+			opp-hz = /bits/ 64 <300000000>;
+			opp-microvolt = <1100000>;
+			clock-latency-ns = <300000>;
+		};
+		opp-600000000 {
+			opp-hz = /bits/ 64 <600000000>;
+			opp-microvolt = <1100000>;
+			clock-latency-ns = <300000>;
+		};
+		opp-1200000000 {
+			opp-hz = /bits/ 64 <1200000000>;
+			opp-microvolt = <1100000>;
+			clock-latency-ns = <300000>;
+			opp-suspend;
+		};
 	};
 
 	cpus {
@@ -66,8 +88,11 @@
 			compatible = "arm,cortex-a55";
 			reg = <0>;
 			device_type = "cpu";
+			#cooling-cells = <2>;
 			next-level-cache = <&L3_CA55>;
 			enable-method = "psci";
+			clocks = <&cpg CPG_CORE R9A07G044_CLK_I>;
+			operating-points-v2 = <&cluster0_opp>;
 		};
 
 		cpu1: cpu@100 {
@@ -76,6 +101,8 @@
 			device_type = "cpu";
 			next-level-cache = <&L3_CA55>;
 			enable-method = "psci";
+			clocks = <&cpg CPG_CORE R9A07G044_CLK_I>;
+			operating-points-v2 = <&cluster0_opp>;
 		};
 
 		L3_CA55: cache-controller-0 {
@@ -85,6 +112,55 @@
 		};
 	};
 
+	gpu_opp_table: opp-table-1 {
+		compatible = "operating-points-v2";
+
+		opp-500000000 {
+			opp-hz = /bits/ 64 <500000000>;
+			opp-microvolt = <1100000>;
+		};
+
+		opp-400000000 {
+			opp-hz = /bits/ 64 <400000000>;
+			opp-microvolt = <1100000>;
+		};
+
+		opp-250000000 {
+			opp-hz = /bits/ 64 <250000000>;
+			opp-microvolt = <1100000>;
+		};
+
+		opp-200000000 {
+			opp-hz = /bits/ 64 <200000000>;
+			opp-microvolt = <1100000>;
+		};
+
+		opp-125000000 {
+			opp-hz = /bits/ 64 <125000000>;
+			opp-microvolt = <1100000>;
+		};
+
+		opp-100000000 {
+			opp-hz = /bits/ 64 <100000000>;
+			opp-microvolt = <1100000>;
+		};
+
+		opp-62500000 {
+			opp-hz = /bits/ 64 <62500000>;
+			opp-microvolt = <1100000>;
+		};
+
+		opp-50000000 {
+			opp-hz = /bits/ 64 <50000000>;
+			opp-microvolt = <1100000>;
+		};
+	};
+
+	psci {
+		compatible = "arm,psci-1.0", "arm,psci-0.2";
+		method = "smc";
+	};
+
 	soc: soc {
 		compatible = "simple-bus";
 		interrupt-parent = <&gic>;
@@ -176,6 +252,60 @@
 			status = "disabled";
 		};
 
+		spi0: spi@1004ac00 {
+			compatible = "renesas,r9a07g044-rspi", "renesas,rspi-rz";
+			reg = <0 0x1004ac00 0 0x400>;
+			interrupts = <GIC_SPI 415 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 413 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 414 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "error", "rx", "tx";
+			clocks = <&cpg CPG_MOD R9A07G044_RSPI0_CLKB>;
+			resets = <&cpg R9A07G044_RSPI0_RST>;
+			dmas = <&dmac 0x2e95>, <&dmac 0x2e96>;
+			dma-names = "tx", "rx";
+			power-domains = <&cpg>;
+			num-cs = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		spi1: spi@1004b000 {
+			compatible = "renesas,r9a07g044-rspi", "renesas,rspi-rz";
+			reg = <0 0x1004b000 0 0x400>;
+			interrupts = <GIC_SPI 418 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 416 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 417 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "error", "rx", "tx";
+			clocks = <&cpg CPG_MOD R9A07G044_RSPI1_CLKB>;
+			resets = <&cpg R9A07G044_RSPI1_RST>;
+			dmas = <&dmac 0x2e99>, <&dmac 0x2e9a>;
+			dma-names = "tx", "rx";
+			power-domains = <&cpg>;
+			num-cs = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		spi2: spi@1004b400 {
+			compatible = "renesas,r9a07g044-rspi", "renesas,rspi-rz";
+			reg = <0 0x1004b400 0 0x400>;
+			interrupts = <GIC_SPI 421 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 419 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 420 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "error", "rx", "tx";
+			clocks = <&cpg CPG_MOD R9A07G044_RSPI2_CLKB>;
+			resets = <&cpg R9A07G044_RSPI2_RST>;
+			dmas = <&dmac 0x2e9d>, <&dmac 0x2e9e>;
+			dma-names = "tx", "rx";
+			power-domains = <&cpg>;
+			num-cs = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
 		scif0: serial@1004b800 {
 			compatible = "renesas,scif-r9a07g044";
 			reg = <0 0x1004b800 0 0x400>;
@@ -194,6 +324,108 @@
 			status = "disabled";
 		};
 
+		scif1: serial@1004bc00 {
+			compatible = "renesas,scif-r9a07g044";
+			reg = <0 0x1004bc00 0 0x400>;
+			interrupts = <GIC_SPI 385 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 387 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 388 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 386 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 389 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 389 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "eri", "rxi", "txi",
+					  "bri", "dri", "tei";
+			clocks = <&cpg CPG_MOD R9A07G044_SCIF1_CLK_PCK>;
+			clock-names = "fck";
+			power-domains = <&cpg>;
+			resets = <&cpg R9A07G044_SCIF1_RST_SYSTEM_N>;
+			status = "disabled";
+		};
+
+		scif2: serial@1004c000 {
+			compatible = "renesas,scif-r9a07g044";
+			reg = <0 0x1004c000 0 0x400>;
+			interrupts = <GIC_SPI 390 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 392 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 393 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 391 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 394 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 394 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "eri", "rxi", "txi",
+					  "bri", "dri", "tei";
+			clocks = <&cpg CPG_MOD R9A07G044_SCIF2_CLK_PCK>;
+			clock-names = "fck";
+			power-domains = <&cpg>;
+			resets = <&cpg R9A07G044_SCIF2_RST_SYSTEM_N>;
+			status = "disabled";
+		};
+
+		scif3: serial@1004c400 {
+			compatible = "renesas,scif-r9a07g044";
+			reg = <0 0x1004c400 0 0x400>;
+			interrupts = <GIC_SPI 395 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 397 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 398 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 396 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 399 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 399 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "eri", "rxi", "txi",
+					  "bri", "dri", "tei";
+			clocks = <&cpg CPG_MOD R9A07G044_SCIF3_CLK_PCK>;
+			clock-names = "fck";
+			power-domains = <&cpg>;
+			resets = <&cpg R9A07G044_SCIF3_RST_SYSTEM_N>;
+			status = "disabled";
+		};
+
+		scif4: serial@1004c800 {
+			compatible = "renesas,scif-r9a07g044";
+			reg = <0 0x1004c800 0 0x400>;
+			interrupts = <GIC_SPI 400 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 402 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 403 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 401 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 404 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 404 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "eri", "rxi", "txi",
+					  "bri", "dri", "tei";
+			clocks = <&cpg CPG_MOD R9A07G044_SCIF4_CLK_PCK>;
+			clock-names = "fck";
+			power-domains = <&cpg>;
+			resets = <&cpg R9A07G044_SCIF4_RST_SYSTEM_N>;
+			status = "disabled";
+		};
+
+		sci0: serial@1004d000 {
+			compatible = "renesas,r9a07g044-sci", "renesas,sci";
+			reg = <0 0x1004d000 0 0x400>;
+			interrupts = <GIC_SPI 405 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 406 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 407 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 408 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "eri", "rxi", "txi", "tei";
+			clocks = <&cpg CPG_MOD R9A07G044_SCI0_CLKP>;
+			clock-names = "fck";
+			power-domains = <&cpg>;
+			resets = <&cpg R9A07G044_SCI0_RST>;
+			status = "disabled";
+		};
+
+		sci1: serial@1004d400 {
+			compatible = "renesas,r9a07g044-sci", "renesas,sci";
+			reg = <0 0x1004d400 0 0x400>;
+			interrupts = <GIC_SPI 409 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 410 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 411 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 412 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "eri", "rxi", "txi", "tei";
+			clocks = <&cpg CPG_MOD R9A07G044_SCI1_CLKP>;
+			clock-names = "fck";
+			power-domains = <&cpg>;
+			resets = <&cpg R9A07G044_SCI1_RST>;
+			status = "disabled";
+		};
+
 		canfd: can@10050000 {
 			compatible = "renesas,r9a07g044-canfd", "renesas,rzg2l-canfd";
 			reg = <0 0x10050000 0 0x8000>;
@@ -358,6 +590,16 @@
 			};
 		};
 
+		tsu: thermal@10059400 {
+			compatible = "renesas,r9a07g044-tsu",
+				     "renesas,rzg2l-tsu";
+			reg = <0 0x10059400 0 0x400>;
+			clocks = <&cpg CPG_MOD R9A07G044_TSU_PCLK>;
+			resets = <&cpg R9A07G044_TSU_PRESETN>;
+			power-domains = <&cpg>;
+			#thermal-sensor-cells = <1>;
+		};
+
 		sbc: spi@10060000 {
 			compatible = "renesas,r9a07g044-rpc-if",
 				     "renesas,rzg2l-rpc-if";
@@ -397,11 +639,15 @@
 			status = "disabled";
 		};
 
-		pinctrl: pin-controller@11030000 {
+		pinctrl: pinctrl@11030000 {
 			compatible = "renesas,r9a07g044-pinctrl";
 			reg = <0 0x11030000 0 0x10000>;
 			gpio-controller;
 			#gpio-cells = <2>;
+			#address-cells = <2>;
+			#interrupt-cells = <2>;
+			interrupt-parent = <&irqc>;
+			interrupt-controller;
 			gpio-ranges = <&pinctrl 0 0 392>;
 			clocks = <&cpg CPG_MOD R9A07G044_GPIO_HCLK>;
 			power-domains = <&cpg>;
@@ -410,6 +656,61 @@
 				 <&cpg R9A07G044_GPIO_SPARE_RESETN>;
 		};
 
+		irqc: interrupt-controller@110a0000 {
+			compatible = "renesas,r9a07g044-irqc",
+				     "renesas,rzg2l-irqc";
+			#interrupt-cells = <2>;
+			#address-cells = <0>;
+			interrupt-controller;
+			reg = <0 0x110a0000 0 0x10000>;
+			interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 444 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 445 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 446 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 447 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 448 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 449 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 450 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 451 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 452 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 453 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 454 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 455 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 456 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 457 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 458 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 459 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 460 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 461 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 462 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 463 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 464 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 465 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 466 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 467 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 468 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 469 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 470 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 471 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 472 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 473 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 474 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 475 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD R9A07G044_IA55_CLK>,
+				 <&cpg CPG_MOD R9A07G044_IA55_PCLK>;
+			clock-names = "clk", "pclk";
+			power-domains = <&cpg>;
+			resets = <&cpg R9A07G044_IA55_RESETN>;
+		};
+
 		dmac: dma-controller@11820000 {
 			compatible = "renesas,r9a07g044-dmac",
 				     "renesas,rz-dmac";
@@ -446,6 +747,27 @@
 			dma-channels = <16>;
 		};
 
+		gpu: gpu@11840000 {
+			compatible = "renesas,r9a07g044-mali",
+				     "arm,mali-bifrost";
+			reg = <0x0 0x11840000 0x0 0x10000>;
+			interrupts = <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 156 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "job", "mmu", "gpu", "event";
+			clocks = <&cpg CPG_MOD R9A07G044_GPU_CLK>,
+				 <&cpg CPG_MOD R9A07G044_GPU_AXI_CLK>,
+				 <&cpg CPG_MOD R9A07G044_GPU_ACE_CLK>;
+			clock-names = "gpu", "bus", "bus_ace";
+			power-domains = <&cpg>;
+			resets = <&cpg R9A07G044_GPU_RESETN>,
+				 <&cpg R9A07G044_GPU_AXI_RESETN>,
+				 <&cpg R9A07G044_GPU_ACE_RESETN>;
+			reset-names = "rst", "axi_rst", "ace_rst";
+			operating-points-v2 = <&gpu_opp_table>;
+		};
+
 		gic: interrupt-controller@11900000 {
 			compatible = "arm,gic-v3";
 			#interrupt-cells = <3>;
@@ -456,17 +778,17 @@
 			interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_LOW>;
 		};
 
-		sdhi0: mmc@11c00000  {
+		sdhi0: mmc@11c00000 {
 			compatible = "renesas,sdhi-r9a07g044",
 				     "renesas,rcar-gen3-sdhi";
 			reg = <0x0 0x11c00000 0 0x10000>;
 			interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD R9A07G044_SDHI0_IMCLK>,
-				 <&cpg CPG_MOD R9A07G044_SDHI0_IMCLK2>,
 				 <&cpg CPG_MOD R9A07G044_SDHI0_CLK_HS>,
+				 <&cpg CPG_MOD R9A07G044_SDHI0_IMCLK2>,
 				 <&cpg CPG_MOD R9A07G044_SDHI0_ACLK>;
-			clock-names = "imclk", "imclk2", "clk_hs", "aclk";
+			clock-names = "core", "clkh", "cd", "aclk";
 			resets = <&cpg R9A07G044_SDHI0_IXRST>;
 			power-domains = <&cpg>;
 			status = "disabled";
@@ -479,10 +801,10 @@
 			interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>,
 				     <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&cpg CPG_MOD R9A07G044_SDHI1_IMCLK>,
-				 <&cpg CPG_MOD R9A07G044_SDHI1_IMCLK2>,
 				 <&cpg CPG_MOD R9A07G044_SDHI1_CLK_HS>,
+				 <&cpg CPG_MOD R9A07G044_SDHI1_IMCLK2>,
 				 <&cpg CPG_MOD R9A07G044_SDHI1_ACLK>;
-			clock-names = "imclk", "imclk2", "clk_hs", "aclk";
+			clock-names = "core", "clkh", "cd", "aclk";
 			resets = <&cpg R9A07G044_SDHI1_IXRST>;
 			power-domains = <&cpg>;
 			status = "disabled";
@@ -641,6 +963,115 @@
 			power-domains = <&cpg>;
 			status = "disabled";
 		};
+
+		wdt0: watchdog@12800800 {
+			compatible = "renesas,r9a07g044-wdt",
+				     "renesas,rzg2l-wdt";
+			reg = <0 0x12800800 0 0x400>;
+			clocks = <&cpg CPG_MOD R9A07G044_WDT0_PCLK>,
+				 <&cpg CPG_MOD R9A07G044_WDT0_CLK>;
+			clock-names = "pclk", "oscclk";
+			interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "wdt", "perrout";
+			resets = <&cpg R9A07G044_WDT0_PRESETN>;
+			power-domains = <&cpg>;
+			status = "disabled";
+		};
+
+		wdt1: watchdog@12800c00 {
+			compatible = "renesas,r9a07g044-wdt",
+				     "renesas,rzg2l-wdt";
+			reg = <0 0x12800C00 0 0x400>;
+			clocks = <&cpg CPG_MOD R9A07G044_WDT1_PCLK>,
+				 <&cpg CPG_MOD R9A07G044_WDT1_CLK>;
+			clock-names = "pclk", "oscclk";
+			interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "wdt", "perrout";
+			resets = <&cpg R9A07G044_WDT1_PRESETN>;
+			power-domains = <&cpg>;
+			status = "disabled";
+		};
+
+		wdt2: watchdog@12800400 {
+			compatible = "renesas,r9a07g044-wdt",
+				     "renesas,rzg2l-wdt";
+			reg = <0 0x12800400 0 0x400>;
+			clocks = <&cpg CPG_MOD R9A07G044_WDT2_PCLK>,
+				 <&cpg CPG_MOD R9A07G044_WDT2_CLK>;
+			clock-names = "pclk", "oscclk";
+			interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "wdt", "perrout";
+			resets = <&cpg R9A07G044_WDT2_PRESETN>;
+			power-domains = <&cpg>;
+			status = "disabled";
+		};
+
+		ostm0: timer@12801000 {
+			compatible = "renesas,r9a07g044-ostm",
+				     "renesas,ostm";
+			reg = <0x0 0x12801000 0x0 0x400>;
+			interrupts = <GIC_SPI 46 IRQ_TYPE_EDGE_RISING>;
+			clocks = <&cpg CPG_MOD R9A07G044_OSTM0_PCLK>;
+			resets = <&cpg R9A07G044_OSTM0_PRESETZ>;
+			power-domains = <&cpg>;
+			status = "disabled";
+		};
+
+		ostm1: timer@12801400 {
+			compatible = "renesas,r9a07g044-ostm",
+				     "renesas,ostm";
+			reg = <0x0 0x12801400 0x0 0x400>;
+			interrupts = <GIC_SPI 47 IRQ_TYPE_EDGE_RISING>;
+			clocks = <&cpg CPG_MOD R9A07G044_OSTM1_PCLK>;
+			resets = <&cpg R9A07G044_OSTM1_PRESETZ>;
+			power-domains = <&cpg>;
+			status = "disabled";
+		};
+
+		ostm2: timer@12801800 {
+			compatible = "renesas,r9a07g044-ostm",
+				     "renesas,ostm";
+			reg = <0x0 0x12801800 0x0 0x400>;
+			interrupts = <GIC_SPI 48 IRQ_TYPE_EDGE_RISING>;
+			clocks = <&cpg CPG_MOD R9A07G044_OSTM2_PCLK>;
+			resets = <&cpg R9A07G044_OSTM2_PRESETZ>;
+			power-domains = <&cpg>;
+			status = "disabled";
+		};
+	};
+
+	thermal-zones {
+		cpu-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+			thermal-sensors = <&tsu 0>;
+			sustainable-power = <717>;
+
+			cooling-maps {
+				map0 {
+					trip = <&target>;
+					cooling-device = <&cpu0 0 2>;
+					contribution = <1024>;
+				};
+			};
+
+			trips {
+				sensor_crit: sensor-crit {
+					temperature = <125000>;
+					hysteresis = <1000>;
+					type = "critical";
+				};
+
+				target: trip-point {
+					temperature = <100000>;
+					hysteresis = <1000>;
+					type = "passive";
+				};
+			};
+		};
 	};
 
 	timer {
diff --git a/arch/arm64/boot/dts/renesas/r9a07g044c1.dtsi b/arch/arm64/boot/dts/renesas/r9a07g044c1.dtsi
new file mode 100644
index 000000000000..1d57df706939
--- /dev/null
+++ b/arch/arm64/boot/dts/renesas/r9a07g044c1.dtsi
@@ -0,0 +1,32 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+/*
+ * Device Tree Source for the RZ/G2LC R9A07G044C1 SoC specific parts
+ *
+ * Copyright (C) 2021 Renesas Electronics Corp.
+ */
+
+/dts-v1/;
+#include "r9a07g044.dtsi"
+
+/ {
+	compatible = "renesas,r9a07g044c1", "renesas,r9a07g044";
+
+	cpus {
+		/delete-node/ cpu-map;
+		/delete-node/ cpu@100;
+	};
+
+	timer {
+		interrupts-extended = <&gic GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
+				      <&gic GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
+				      <&gic GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
+				      <&gic GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>;
+	};
+};
+
+&soc {
+	/delete-node/ ssi@1004a800;
+	/delete-node/ serial@1004c800;
+	/delete-node/ adc@10059000;
+	/delete-node/ ethernet@11c30000;
+};
diff --git a/arch/arm64/boot/dts/renesas/r9a07g044c2-smarc.dts b/arch/arm64/boot/dts/renesas/r9a07g044c2-smarc.dts
new file mode 100644
index 000000000000..fc34058002e2
--- /dev/null
+++ b/arch/arm64/boot/dts/renesas/r9a07g044c2-smarc.dts
@@ -0,0 +1,15 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+/*
+ * Device Tree Source for the RZ/G2LC SMARC EVK board
+ *
+ * Copyright (C) 2021 Renesas Electronics Corp.
+ */
+
+/dts-v1/;
+#include "r9a07g044c2.dtsi"
+#include "rzg2lc-smarc.dtsi"
+
+/ {
+	model = "Renesas SMARC EVK based on r9a07g044c2";
+	compatible = "renesas,smarc-evk", "renesas,r9a07g044c2", "renesas,r9a07g044";
+};
diff --git a/arch/arm64/boot/dts/renesas/r9a07g044c2.dtsi b/arch/arm64/boot/dts/renesas/r9a07g044c2.dtsi
new file mode 100644
index 000000000000..7bb8917fe421
--- /dev/null
+++ b/arch/arm64/boot/dts/renesas/r9a07g044c2.dtsi
@@ -0,0 +1,20 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+/*
+ * Device Tree Source for the RZ/G2LC R9A07G044C2 SoC specific parts
+ *
+ * Copyright (C) 2021 Renesas Electronics Corp.
+ */
+
+/dts-v1/;
+#include "r9a07g044.dtsi"
+
+/ {
+	compatible = "renesas,r9a07g044c2", "renesas,r9a07g044";
+};
+
+&soc {
+	/delete-node/ ssi@1004a800;
+	/delete-node/ serial@1004c800;
+	/delete-node/ adc@10059000;
+	/delete-node/ ethernet@11c30000;
+};
diff --git a/arch/arm64/boot/dts/renesas/r9a07g044l2-smarc.dts b/arch/arm64/boot/dts/renesas/r9a07g044l2-smarc.dts
index 247b0b3f1b58..bc2af6c92ccd 100644
--- a/arch/arm64/boot/dts/renesas/r9a07g044l2-smarc.dts
+++ b/arch/arm64/boot/dts/renesas/r9a07g044l2-smarc.dts
@@ -8,6 +8,8 @@
 /dts-v1/;
 #include "r9a07g044l2.dtsi"
 #include "rzg2l-smarc-som.dtsi"
+#include "rzg2l-smarc-pinfunction.dtsi"
+#include "rz-smarc-common.dtsi"
 #include "rzg2l-smarc.dtsi"
 
 / {
diff --git a/arch/arm64/boot/dts/renesas/r9a07g054.dtsi b/arch/arm64/boot/dts/renesas/r9a07g054.dtsi
new file mode 100644
index 000000000000..358d4c34465f
--- /dev/null
+++ b/arch/arm64/boot/dts/renesas/r9a07g054.dtsi
@@ -0,0 +1,1090 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+/*
+ * Device Tree Source for the RZ/V2L SoC
+ *
+ * Copyright (C) 2021 Renesas Electronics Corp.
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/r9a07g054-cpg.h>
+
+/ {
+	compatible = "renesas,r9a07g054";
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	audio_clk1: audio1-clk {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		/* This value must be overridden by boards that provide it */
+		clock-frequency = <0>;
+	};
+
+	audio_clk2: audio2-clk {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		/* This value must be overridden by boards that provide it */
+		clock-frequency = <0>;
+	};
+
+	/* External CAN clock - to be overridden by boards that provide it */
+	can_clk: can-clk {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <0>;
+	};
+
+	/* clock can be either from exclk or crystal oscillator (XIN/XOUT) */
+	extal_clk: extal-clk {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		/* This value must be overridden by the board */
+		clock-frequency = <0>;
+	};
+
+	cluster0_opp: opp-table-0 {
+		compatible = "operating-points-v2";
+		opp-shared;
+
+		opp-150000000 {
+			opp-hz = /bits/ 64 <150000000>;
+			opp-microvolt = <1100000>;
+			clock-latency-ns = <300000>;
+		};
+		opp-300000000 {
+			opp-hz = /bits/ 64 <300000000>;
+			opp-microvolt = <1100000>;
+			clock-latency-ns = <300000>;
+		};
+		opp-600000000 {
+			opp-hz = /bits/ 64 <600000000>;
+			opp-microvolt = <1100000>;
+			clock-latency-ns = <300000>;
+		};
+		opp-1200000000 {
+			opp-hz = /bits/ 64 <1200000000>;
+			opp-microvolt = <1100000>;
+			clock-latency-ns = <300000>;
+			opp-suspend;
+		};
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu-map {
+			cluster0 {
+				core0 {
+					cpu = <&cpu0>;
+				};
+				core1 {
+					cpu = <&cpu1>;
+				};
+			};
+		};
+
+		cpu0: cpu@0 {
+			compatible = "arm,cortex-a55";
+			reg = <0>;
+			device_type = "cpu";
+			#cooling-cells = <2>;
+			next-level-cache = <&L3_CA55>;
+			enable-method = "psci";
+			clocks = <&cpg CPG_CORE R9A07G054_CLK_I>;
+			operating-points-v2 = <&cluster0_opp>;
+		};
+
+		cpu1: cpu@100 {
+			compatible = "arm,cortex-a55";
+			reg = <0x100>;
+			device_type = "cpu";
+			next-level-cache = <&L3_CA55>;
+			enable-method = "psci";
+			clocks = <&cpg CPG_CORE R9A07G054_CLK_I>;
+			operating-points-v2 = <&cluster0_opp>;
+		};
+
+		L3_CA55: cache-controller-0 {
+			compatible = "cache";
+			cache-unified;
+			cache-size = <0x40000>;
+		};
+	};
+
+	gpu_opp_table: opp-table-1 {
+		compatible = "operating-points-v2";
+
+		opp-500000000 {
+			opp-hz = /bits/ 64 <500000000>;
+			opp-microvolt = <1100000>;
+		};
+
+		opp-400000000 {
+			opp-hz = /bits/ 64 <400000000>;
+			opp-microvolt = <1100000>;
+		};
+
+		opp-250000000 {
+			opp-hz = /bits/ 64 <250000000>;
+			opp-microvolt = <1100000>;
+		};
+
+		opp-200000000 {
+			opp-hz = /bits/ 64 <200000000>;
+			opp-microvolt = <1100000>;
+		};
+
+		opp-125000000 {
+			opp-hz = /bits/ 64 <125000000>;
+			opp-microvolt = <1100000>;
+		};
+
+		opp-100000000 {
+			opp-hz = /bits/ 64 <100000000>;
+			opp-microvolt = <1100000>;
+		};
+
+		opp-62500000 {
+			opp-hz = /bits/ 64 <62500000>;
+			opp-microvolt = <1100000>;
+		};
+
+		opp-50000000 {
+			opp-hz = /bits/ 64 <50000000>;
+			opp-microvolt = <1100000>;
+		};
+	};
+
+	psci {
+		compatible = "arm,psci-1.0", "arm,psci-0.2";
+		method = "smc";
+	};
+
+	soc: soc {
+		compatible = "simple-bus";
+		interrupt-parent = <&gic>;
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		ssi0: ssi@10049c00 {
+			compatible = "renesas,r9a07g054-ssi",
+				     "renesas,rz-ssi";
+			reg = <0 0x10049c00 0 0x400>;
+			interrupts = <GIC_SPI 326 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 327 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 328 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 329 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "int_req", "dma_rx", "dma_tx", "dma_rt";
+			clocks = <&cpg CPG_MOD R9A07G054_SSI0_PCLK2>,
+				 <&cpg CPG_MOD R9A07G054_SSI0_PCLK_SFR>,
+				 <&audio_clk1>, <&audio_clk2>;
+			clock-names = "ssi", "ssi_sfr", "audio_clk1", "audio_clk2";
+			resets = <&cpg R9A07G054_SSI0_RST_M2_REG>;
+			dmas = <&dmac 0x2655>, <&dmac 0x2656>;
+			dma-names = "tx", "rx";
+			power-domains = <&cpg>;
+			#sound-dai-cells = <0>;
+			status = "disabled";
+		};
+
+		ssi1: ssi@1004a000 {
+			compatible = "renesas,r9a07g054-ssi",
+				     "renesas,rz-ssi";
+			reg = <0 0x1004a000 0 0x400>;
+			interrupts = <GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 331 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 332 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 333 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "int_req", "dma_rx", "dma_tx", "dma_rt";
+			clocks = <&cpg CPG_MOD R9A07G054_SSI1_PCLK2>,
+				 <&cpg CPG_MOD R9A07G054_SSI1_PCLK_SFR>,
+				 <&audio_clk1>, <&audio_clk2>;
+			clock-names = "ssi", "ssi_sfr", "audio_clk1", "audio_clk2";
+			resets = <&cpg R9A07G054_SSI1_RST_M2_REG>;
+			dmas = <&dmac 0x2659>, <&dmac 0x265a>;
+			dma-names = "tx", "rx";
+			power-domains = <&cpg>;
+			#sound-dai-cells = <0>;
+			status = "disabled";
+		};
+
+		ssi2: ssi@1004a400 {
+			compatible = "renesas,r9a07g054-ssi",
+				     "renesas,rz-ssi";
+			reg = <0 0x1004a400 0 0x400>;
+			interrupts = <GIC_SPI 334 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 335 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 336 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 337 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "int_req", "dma_rx", "dma_tx", "dma_rt";
+			clocks = <&cpg CPG_MOD R9A07G054_SSI2_PCLK2>,
+				 <&cpg CPG_MOD R9A07G054_SSI2_PCLK_SFR>,
+				 <&audio_clk1>, <&audio_clk2>;
+			clock-names = "ssi", "ssi_sfr", "audio_clk1", "audio_clk2";
+			resets = <&cpg R9A07G054_SSI2_RST_M2_REG>;
+			dmas = <&dmac 0x265f>;
+			dma-names = "rt";
+			power-domains = <&cpg>;
+			#sound-dai-cells = <0>;
+			status = "disabled";
+		};
+
+		ssi3: ssi@1004a800 {
+			compatible = "renesas,r9a07g054-ssi",
+				     "renesas,rz-ssi";
+			reg = <0 0x1004a800 0 0x400>;
+			interrupts = <GIC_SPI 338 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 339 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 340 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 341 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "int_req", "dma_rx", "dma_tx", "dma_rt";
+			clocks = <&cpg CPG_MOD R9A07G054_SSI3_PCLK2>,
+				 <&cpg CPG_MOD R9A07G054_SSI3_PCLK_SFR>,
+				 <&audio_clk1>, <&audio_clk2>;
+			clock-names = "ssi", "ssi_sfr", "audio_clk1", "audio_clk2";
+			resets = <&cpg R9A07G054_SSI3_RST_M2_REG>;
+			dmas = <&dmac 0x2661>, <&dmac 0x2662>;
+			dma-names = "tx", "rx";
+			power-domains = <&cpg>;
+			#sound-dai-cells = <0>;
+			status = "disabled";
+		};
+
+		spi0: spi@1004ac00 {
+			compatible = "renesas,r9a07g054-rspi", "renesas,rspi-rz";
+			reg = <0 0x1004ac00 0 0x400>;
+			interrupts = <GIC_SPI 415 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 413 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 414 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "error", "rx", "tx";
+			clocks = <&cpg CPG_MOD R9A07G054_RSPI0_CLKB>;
+			resets = <&cpg R9A07G054_RSPI0_RST>;
+			dmas = <&dmac 0x2e95>, <&dmac 0x2e96>;
+			dma-names = "tx", "rx";
+			power-domains = <&cpg>;
+			num-cs = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		spi1: spi@1004b000 {
+			compatible = "renesas,r9a07g054-rspi", "renesas,rspi-rz";
+			reg = <0 0x1004b000 0 0x400>;
+			interrupts = <GIC_SPI 418 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 416 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 417 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "error", "rx", "tx";
+			clocks = <&cpg CPG_MOD R9A07G054_RSPI1_CLKB>;
+			resets = <&cpg R9A07G054_RSPI1_RST>;
+			dmas = <&dmac 0x2e99>, <&dmac 0x2e9a>;
+			dma-names = "tx", "rx";
+			power-domains = <&cpg>;
+			num-cs = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		spi2: spi@1004b400 {
+			compatible = "renesas,r9a07g054-rspi", "renesas,rspi-rz";
+			reg = <0 0x1004b400 0 0x400>;
+			interrupts = <GIC_SPI 421 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 419 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 420 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "error", "rx", "tx";
+			clocks = <&cpg CPG_MOD R9A07G054_RSPI2_CLKB>;
+			resets = <&cpg R9A07G054_RSPI2_RST>;
+			dmas = <&dmac 0x2e9d>, <&dmac 0x2e9e>;
+			dma-names = "tx", "rx";
+			power-domains = <&cpg>;
+			num-cs = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		scif0: serial@1004b800 {
+			compatible = "renesas,scif-r9a07g054",
+				     "renesas,scif-r9a07g044";
+			reg = <0 0x1004b800 0 0x400>;
+			interrupts = <GIC_SPI 380 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 382 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 383 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 381 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 384 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 384 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "eri", "rxi", "txi",
+					  "bri", "dri", "tei";
+			clocks = <&cpg CPG_MOD R9A07G054_SCIF0_CLK_PCK>;
+			clock-names = "fck";
+			power-domains = <&cpg>;
+			resets = <&cpg R9A07G054_SCIF0_RST_SYSTEM_N>;
+			status = "disabled";
+		};
+
+		scif1: serial@1004bc00 {
+			compatible = "renesas,scif-r9a07g054",
+				     "renesas,scif-r9a07g044";
+			reg = <0 0x1004bc00 0 0x400>;
+			interrupts = <GIC_SPI 385 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 387 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 388 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 386 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 389 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 389 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "eri", "rxi", "txi",
+					  "bri", "dri", "tei";
+			clocks = <&cpg CPG_MOD R9A07G054_SCIF1_CLK_PCK>;
+			clock-names = "fck";
+			power-domains = <&cpg>;
+			resets = <&cpg R9A07G054_SCIF1_RST_SYSTEM_N>;
+			status = "disabled";
+		};
+
+		scif2: serial@1004c000 {
+			compatible = "renesas,scif-r9a07g054",
+				     "renesas,scif-r9a07g044";
+			reg = <0 0x1004c000 0 0x400>;
+			interrupts = <GIC_SPI 390 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 392 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 393 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 391 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 394 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 394 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "eri", "rxi", "txi",
+					  "bri", "dri", "tei";
+			clocks = <&cpg CPG_MOD R9A07G054_SCIF2_CLK_PCK>;
+			clock-names = "fck";
+			power-domains = <&cpg>;
+			resets = <&cpg R9A07G054_SCIF2_RST_SYSTEM_N>;
+			status = "disabled";
+		};
+
+		scif3: serial@1004c400 {
+			compatible = "renesas,scif-r9a07g054",
+				     "renesas,scif-r9a07g044";
+			reg = <0 0x1004c400 0 0x400>;
+			interrupts = <GIC_SPI 395 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 397 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 398 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 396 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 399 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 399 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "eri", "rxi", "txi",
+					  "bri", "dri", "tei";
+			clocks = <&cpg CPG_MOD R9A07G054_SCIF3_CLK_PCK>;
+			clock-names = "fck";
+			power-domains = <&cpg>;
+			resets = <&cpg R9A07G054_SCIF3_RST_SYSTEM_N>;
+			status = "disabled";
+		};
+
+		scif4: serial@1004c800 {
+			compatible = "renesas,scif-r9a07g054",
+				     "renesas,scif-r9a07g044";
+			reg = <0 0x1004c800 0 0x400>;
+			interrupts = <GIC_SPI 400 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 402 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 403 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 401 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 404 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 404 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "eri", "rxi", "txi",
+					  "bri", "dri", "tei";
+			clocks = <&cpg CPG_MOD R9A07G054_SCIF4_CLK_PCK>;
+			clock-names = "fck";
+			power-domains = <&cpg>;
+			resets = <&cpg R9A07G054_SCIF4_RST_SYSTEM_N>;
+			status = "disabled";
+		};
+
+		sci0: serial@1004d000 {
+			compatible = "renesas,r9a07g054-sci", "renesas,sci";
+			reg = <0 0x1004d000 0 0x400>;
+			interrupts = <GIC_SPI 405 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 406 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 407 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 408 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "eri", "rxi", "txi", "tei";
+			clocks = <&cpg CPG_MOD R9A07G054_SCI0_CLKP>;
+			clock-names = "fck";
+			power-domains = <&cpg>;
+			resets = <&cpg R9A07G054_SCI0_RST>;
+			status = "disabled";
+		};
+
+		sci1: serial@1004d400 {
+			compatible = "renesas,r9a07g054-sci", "renesas,sci";
+			reg = <0 0x1004d400 0 0x400>;
+			interrupts = <GIC_SPI 409 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 410 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 411 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 412 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "eri", "rxi", "txi", "tei";
+			clocks = <&cpg CPG_MOD R9A07G054_SCI1_CLKP>;
+			clock-names = "fck";
+			power-domains = <&cpg>;
+			resets = <&cpg R9A07G054_SCI1_RST>;
+			status = "disabled";
+		};
+
+		canfd: can@10050000 {
+			compatible = "renesas,r9a07g054-canfd", "renesas,rzg2l-canfd";
+			reg = <0 0x10050000 0 0x8000>;
+			interrupts = <GIC_SPI 426 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 427 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 422 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 424 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 428 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 423 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 425 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 429 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "g_err", "g_recc",
+					  "ch0_err", "ch0_rec", "ch0_trx",
+					  "ch1_err", "ch1_rec", "ch1_trx";
+			clocks = <&cpg CPG_MOD R9A07G054_CANFD_PCLK>,
+				 <&cpg CPG_CORE R9A07G054_CLK_P0_DIV2>,
+				 <&can_clk>;
+			clock-names = "fck", "canfd", "can_clk";
+			assigned-clocks = <&cpg CPG_CORE R9A07G054_CLK_P0_DIV2>;
+			assigned-clock-rates = <50000000>;
+			resets = <&cpg R9A07G054_CANFD_RSTP_N>,
+				 <&cpg R9A07G054_CANFD_RSTC_N>;
+			reset-names = "rstp_n", "rstc_n";
+			power-domains = <&cpg>;
+			status = "disabled";
+
+			channel0 {
+				status = "disabled";
+			};
+			channel1 {
+				status = "disabled";
+			};
+		};
+
+		i2c0: i2c@10058000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "renesas,riic-r9a07g054", "renesas,riic-rz";
+			reg = <0 0x10058000 0 0x400>;
+			interrupts = <GIC_SPI 350 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 348 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 349 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 352 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 351 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "tei", "ri", "ti", "spi", "sti",
+					  "naki", "ali", "tmoi";
+			clocks = <&cpg CPG_MOD R9A07G054_I2C0_PCLK>;
+			clock-frequency = <100000>;
+			resets = <&cpg R9A07G054_I2C0_MRST>;
+			power-domains = <&cpg>;
+			status = "disabled";
+		};
+
+		i2c1: i2c@10058400 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "renesas,riic-r9a07g054", "renesas,riic-rz";
+			reg = <0 0x10058400 0 0x400>;
+			interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 356 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 357 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 360 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 361 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 359 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 362 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 363 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "tei", "ri", "ti", "spi", "sti",
+					  "naki", "ali", "tmoi";
+			clocks = <&cpg CPG_MOD R9A07G054_I2C1_PCLK>;
+			clock-frequency = <100000>;
+			resets = <&cpg R9A07G054_I2C1_MRST>;
+			power-domains = <&cpg>;
+			status = "disabled";
+		};
+
+		i2c2: i2c@10058800 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "renesas,riic-r9a07g054", "renesas,riic-rz";
+			reg = <0 0x10058800 0 0x400>;
+			interrupts = <GIC_SPI 366 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 364 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 365 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 368 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 369 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 367 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 370 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 371 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "tei", "ri", "ti", "spi", "sti",
+					  "naki", "ali", "tmoi";
+			clocks = <&cpg CPG_MOD R9A07G054_I2C2_PCLK>;
+			clock-frequency = <100000>;
+			resets = <&cpg R9A07G054_I2C2_MRST>;
+			power-domains = <&cpg>;
+			status = "disabled";
+		};
+
+		i2c3: i2c@10058c00 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "renesas,riic-r9a07g054", "renesas,riic-rz";
+			reg = <0 0x10058c00 0 0x400>;
+			interrupts = <GIC_SPI 374 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 372 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 373 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 376 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 377 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 375 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 378 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 379 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "tei", "ri", "ti", "spi", "sti",
+					  "naki", "ali", "tmoi";
+			clocks = <&cpg CPG_MOD R9A07G054_I2C3_PCLK>;
+			clock-frequency = <100000>;
+			resets = <&cpg R9A07G054_I2C3_MRST>;
+			power-domains = <&cpg>;
+			status = "disabled";
+		};
+
+		adc: adc@10059000 {
+			compatible = "renesas,r9a07g054-adc", "renesas,rzg2l-adc";
+			reg = <0 0x10059000 0 0x400>;
+			interrupts = <GIC_SPI 347 IRQ_TYPE_EDGE_RISING>;
+			clocks = <&cpg CPG_MOD R9A07G054_ADC_ADCLK>,
+				 <&cpg CPG_MOD R9A07G054_ADC_PCLK>;
+			clock-names = "adclk", "pclk";
+			resets = <&cpg R9A07G054_ADC_PRESETN>,
+				 <&cpg R9A07G054_ADC_ADRST_N>;
+			reset-names = "presetn", "adrst-n";
+			power-domains = <&cpg>;
+			status = "disabled";
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			channel@0 {
+				reg = <0>;
+			};
+			channel@1 {
+				reg = <1>;
+			};
+			channel@2 {
+				reg = <2>;
+			};
+			channel@3 {
+				reg = <3>;
+			};
+			channel@4 {
+				reg = <4>;
+			};
+			channel@5 {
+				reg = <5>;
+			};
+			channel@6 {
+				reg = <6>;
+			};
+			channel@7 {
+				reg = <7>;
+			};
+		};
+
+		tsu: thermal@10059400 {
+			compatible = "renesas,r9a07g054-tsu",
+				     "renesas,rzg2l-tsu";
+			reg = <0 0x10059400 0 0x400>;
+			clocks = <&cpg CPG_MOD R9A07G054_TSU_PCLK>;
+			resets = <&cpg R9A07G054_TSU_PRESETN>;
+			power-domains = <&cpg>;
+			#thermal-sensor-cells = <1>;
+		};
+
+		sbc: spi@10060000 {
+			compatible = "renesas,r9a07g054-rpc-if",
+				     "renesas,rzg2l-rpc-if";
+			reg = <0 0x10060000 0 0x10000>,
+			      <0 0x20000000 0 0x10000000>,
+			      <0 0x10070000 0 0x10000>;
+			reg-names = "regs", "dirmap", "wbuf";
+			interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD R9A07G054_SPI_CLK2>,
+				 <&cpg CPG_MOD R9A07G054_SPI_CLK>;
+			resets = <&cpg R9A07G054_SPI_RST>;
+			power-domains = <&cpg>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		cpg: clock-controller@11010000 {
+			compatible = "renesas,r9a07g054-cpg";
+			reg = <0 0x11010000 0 0x10000>;
+			clocks = <&extal_clk>;
+			clock-names = "extal";
+			#clock-cells = <2>;
+			#reset-cells = <1>;
+			#power-domain-cells = <0>;
+		};
+
+		sysc: system-controller@11020000 {
+			compatible = "renesas,r9a07g054-sysc";
+			reg = <0 0x11020000 0 0x10000>;
+			interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "lpm_int", "ca55stbydone_int",
+					  "cm33stbyr_int", "ca55_deny";
+			status = "disabled";
+		};
+
+		pinctrl: pinctrl@11030000 {
+			compatible = "renesas,r9a07g054-pinctrl",
+				     "renesas,r9a07g044-pinctrl";
+			reg = <0 0x11030000 0 0x10000>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			#address-cells = <2>;
+			#interrupt-cells = <2>;
+			interrupt-parent = <&irqc>;
+			interrupt-controller;
+			gpio-ranges = <&pinctrl 0 0 392>;
+			clocks = <&cpg CPG_MOD R9A07G054_GPIO_HCLK>;
+			power-domains = <&cpg>;
+			resets = <&cpg R9A07G054_GPIO_RSTN>,
+				 <&cpg R9A07G054_GPIO_PORT_RESETN>,
+				 <&cpg R9A07G054_GPIO_SPARE_RESETN>;
+		};
+
+		irqc: interrupt-controller@110a0000 {
+			compatible = "renesas,r9a07g054-irqc",
+				     "renesas,rzg2l-irqc";
+			#interrupt-cells = <2>;
+			#address-cells = <0>;
+			interrupt-controller;
+			reg = <0 0x110a0000 0 0x10000>;
+			interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 444 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 445 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 446 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 447 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 448 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 449 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 450 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 451 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 452 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 453 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 454 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 455 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 456 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 457 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 458 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 459 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 460 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 461 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 462 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 463 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 464 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 465 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 466 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 467 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 468 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 469 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 470 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 471 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 472 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 473 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 474 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 475 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD R9A07G054_IA55_CLK>,
+				 <&cpg CPG_MOD R9A07G054_IA55_PCLK>;
+			clock-names = "clk", "pclk";
+			power-domains = <&cpg>;
+			resets = <&cpg R9A07G054_IA55_RESETN>;
+		};
+
+		dmac: dma-controller@11820000 {
+			compatible = "renesas,r9a07g054-dmac",
+				     "renesas,rz-dmac";
+			reg = <0 0x11820000 0 0x10000>,
+			      <0 0x11830000 0 0x10000>;
+			interrupts = <GIC_SPI 141 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 125 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 126 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 127 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 128 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 129 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 130 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 131 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 132 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 133 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 134 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 135 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 136 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 137 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 138 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 139 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 140 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "error",
+					  "ch0", "ch1", "ch2", "ch3",
+					  "ch4", "ch5", "ch6", "ch7",
+					  "ch8", "ch9", "ch10", "ch11",
+					  "ch12", "ch13", "ch14", "ch15";
+			clocks = <&cpg CPG_MOD R9A07G054_DMAC_ACLK>,
+				 <&cpg CPG_MOD R9A07G054_DMAC_PCLK>;
+			power-domains = <&cpg>;
+			resets = <&cpg R9A07G054_DMAC_ARESETN>,
+				 <&cpg R9A07G054_DMAC_RST_ASYNC>;
+			#dma-cells = <1>;
+			dma-channels = <16>;
+		};
+
+		gpu: gpu@11840000 {
+			compatible = "renesas,r9a07g054-mali",
+				     "arm,mali-bifrost";
+			reg = <0x0 0x11840000 0x0 0x10000>;
+			interrupts = <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 156 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "job", "mmu", "gpu", "event";
+			clocks = <&cpg CPG_MOD R9A07G054_GPU_CLK>,
+				 <&cpg CPG_MOD R9A07G054_GPU_AXI_CLK>,
+				 <&cpg CPG_MOD R9A07G054_GPU_ACE_CLK>;
+			clock-names = "gpu", "bus", "bus_ace";
+			power-domains = <&cpg>;
+			resets = <&cpg R9A07G054_GPU_RESETN>,
+				 <&cpg R9A07G054_GPU_AXI_RESETN>,
+				 <&cpg R9A07G054_GPU_ACE_RESETN>;
+			reset-names = "rst", "axi_rst", "ace_rst";
+			operating-points-v2 = <&gpu_opp_table>;
+		};
+
+		gic: interrupt-controller@11900000 {
+			compatible = "arm,gic-v3";
+			#interrupt-cells = <3>;
+			#address-cells = <0>;
+			interrupt-controller;
+			reg = <0x0 0x11900000 0 0x40000>,
+			      <0x0 0x11940000 0 0x60000>;
+			interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_LOW>;
+		};
+
+		sdhi0: mmc@11c00000 {
+			compatible = "renesas,sdhi-r9a07g054",
+				     "renesas,rcar-gen3-sdhi";
+			reg = <0x0 0x11c00000 0 0x10000>;
+			interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD R9A07G054_SDHI0_IMCLK>,
+				 <&cpg CPG_MOD R9A07G054_SDHI0_CLK_HS>,
+				 <&cpg CPG_MOD R9A07G054_SDHI0_IMCLK2>,
+				 <&cpg CPG_MOD R9A07G054_SDHI0_ACLK>;
+			clock-names = "core", "clkh", "cd", "aclk";
+			resets = <&cpg R9A07G054_SDHI0_IXRST>;
+			power-domains = <&cpg>;
+			status = "disabled";
+		};
+
+		sdhi1: mmc@11c10000 {
+			compatible = "renesas,sdhi-r9a07g054",
+				     "renesas,rcar-gen3-sdhi";
+			reg = <0x0 0x11c10000 0 0x10000>;
+			interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD R9A07G054_SDHI1_IMCLK>,
+				 <&cpg CPG_MOD R9A07G054_SDHI1_CLK_HS>,
+				 <&cpg CPG_MOD R9A07G054_SDHI1_IMCLK2>,
+				 <&cpg CPG_MOD R9A07G054_SDHI1_ACLK>;
+			clock-names = "core", "clkh", "cd", "aclk";
+			resets = <&cpg R9A07G054_SDHI1_IXRST>;
+			power-domains = <&cpg>;
+			status = "disabled";
+		};
+
+		eth0: ethernet@11c20000 {
+			compatible = "renesas,r9a07g054-gbeth",
+				     "renesas,rzg2l-gbeth";
+			reg = <0 0x11c20000 0 0x10000>;
+			interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "mux", "fil", "arp_ns";
+			phy-mode = "rgmii";
+			clocks = <&cpg CPG_MOD R9A07G054_ETH0_CLK_AXI>,
+				 <&cpg CPG_MOD R9A07G054_ETH0_CLK_CHI>,
+				 <&cpg CPG_CORE R9A07G054_CLK_HP>;
+			clock-names = "axi", "chi", "refclk";
+			resets = <&cpg R9A07G054_ETH0_RST_HW_N>;
+			power-domains = <&cpg>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		eth1: ethernet@11c30000 {
+			compatible = "renesas,r9a07g054-gbeth",
+				     "renesas,rzg2l-gbeth";
+			reg = <0 0x11c30000 0 0x10000>;
+			interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "mux", "fil", "arp_ns";
+			phy-mode = "rgmii";
+			clocks = <&cpg CPG_MOD R9A07G054_ETH1_CLK_AXI>,
+				 <&cpg CPG_MOD R9A07G054_ETH1_CLK_CHI>,
+				 <&cpg CPG_CORE R9A07G054_CLK_HP>;
+			clock-names = "axi", "chi", "refclk";
+			resets = <&cpg R9A07G054_ETH1_RST_HW_N>;
+			power-domains = <&cpg>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		phyrst: usbphy-ctrl@11c40000 {
+			compatible = "renesas,r9a07g054-usbphy-ctrl",
+				     "renesas,rzg2l-usbphy-ctrl";
+			reg = <0 0x11c40000 0 0x10000>;
+			clocks = <&cpg CPG_MOD R9A07G054_USB_PCLK>;
+			resets = <&cpg R9A07G054_USB_PRESETN>;
+			power-domains = <&cpg>;
+			#reset-cells = <1>;
+			status = "disabled";
+		};
+
+		ohci0: usb@11c50000 {
+			compatible = "generic-ohci";
+			reg = <0 0x11c50000 0 0x100>;
+			interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD R9A07G054_USB_PCLK>,
+				 <&cpg CPG_MOD R9A07G054_USB_U2H0_HCLK>;
+			resets = <&phyrst 0>,
+				 <&cpg R9A07G054_USB_U2H0_HRESETN>;
+			phys = <&usb2_phy0 1>;
+			phy-names = "usb";
+			power-domains = <&cpg>;
+			status = "disabled";
+		};
+
+		ohci1: usb@11c70000 {
+			compatible = "generic-ohci";
+			reg = <0 0x11c70000 0 0x100>;
+			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD R9A07G054_USB_PCLK>,
+				 <&cpg CPG_MOD R9A07G054_USB_U2H1_HCLK>;
+			resets = <&phyrst 1>,
+				 <&cpg R9A07G054_USB_U2H1_HRESETN>;
+			phys = <&usb2_phy1 1>;
+			phy-names = "usb";
+			power-domains = <&cpg>;
+			status = "disabled";
+		};
+
+		ehci0: usb@11c50100 {
+			compatible = "generic-ehci";
+			reg = <0 0x11c50100 0 0x100>;
+			interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD R9A07G054_USB_PCLK>,
+				 <&cpg CPG_MOD R9A07G054_USB_U2H0_HCLK>;
+			resets = <&phyrst 0>,
+				 <&cpg R9A07G054_USB_U2H0_HRESETN>;
+			phys = <&usb2_phy0 2>;
+			phy-names = "usb";
+			companion = <&ohci0>;
+			power-domains = <&cpg>;
+			status = "disabled";
+		};
+
+		ehci1: usb@11c70100 {
+			compatible = "generic-ehci";
+			reg = <0 0x11c70100 0 0x100>;
+			interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD R9A07G054_USB_PCLK>,
+				 <&cpg CPG_MOD R9A07G054_USB_U2H1_HCLK>;
+			resets = <&phyrst 1>,
+				 <&cpg R9A07G054_USB_U2H1_HRESETN>;
+			phys = <&usb2_phy1 2>;
+			phy-names = "usb";
+			companion = <&ohci1>;
+			power-domains = <&cpg>;
+			status = "disabled";
+		};
+
+		usb2_phy0: usb-phy@11c50200 {
+			compatible = "renesas,usb2-phy-r9a07g054",
+				     "renesas,rzg2l-usb2-phy";
+			reg = <0 0x11c50200 0 0x700>;
+			interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD R9A07G054_USB_PCLK>,
+				 <&cpg CPG_MOD R9A07G054_USB_U2H0_HCLK>;
+			resets = <&phyrst 0>;
+			#phy-cells = <1>;
+			power-domains = <&cpg>;
+			status = "disabled";
+		};
+
+		usb2_phy1: usb-phy@11c70200 {
+			compatible = "renesas,usb2-phy-r9a07g054",
+				     "renesas,rzg2l-usb2-phy";
+			reg = <0 0x11c70200 0 0x700>;
+			interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD R9A07G054_USB_PCLK>,
+				 <&cpg CPG_MOD R9A07G054_USB_U2H1_HCLK>;
+			resets = <&phyrst 1>;
+			#phy-cells = <1>;
+			power-domains = <&cpg>;
+			status = "disabled";
+		};
+
+		hsusb: usb@11c60000 {
+			compatible = "renesas,usbhs-r9a07g054",
+				     "renesas,rza2-usbhs";
+			reg = <0 0x11c60000 0 0x10000>;
+			interrupts = <GIC_SPI 100 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD R9A07G054_USB_PCLK>,
+				 <&cpg CPG_MOD R9A07G054_USB_U2P_EXR_CPUCLK>;
+			resets = <&phyrst 0>,
+				 <&cpg R9A07G054_USB_U2P_EXL_SYSRST>;
+			renesas,buswait = <7>;
+			phys = <&usb2_phy0 3>;
+			phy-names = "usb";
+			power-domains = <&cpg>;
+			status = "disabled";
+		};
+
+		wdt0: watchdog@12800800 {
+			compatible = "renesas,r9a07g054-wdt",
+				     "renesas,rzg2l-wdt";
+			reg = <0 0x12800800 0 0x400>;
+			clocks = <&cpg CPG_MOD R9A07G054_WDT0_PCLK>,
+				 <&cpg CPG_MOD R9A07G054_WDT0_CLK>;
+			clock-names = "pclk", "oscclk";
+			interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "wdt", "perrout";
+			resets = <&cpg R9A07G054_WDT0_PRESETN>;
+			power-domains = <&cpg>;
+			status = "disabled";
+		};
+
+		wdt1: watchdog@12800c00 {
+			compatible = "renesas,r9a07g054-wdt",
+				     "renesas,rzg2l-wdt";
+			reg = <0 0x12800C00 0 0x400>;
+			clocks = <&cpg CPG_MOD R9A07G054_WDT1_PCLK>,
+				 <&cpg CPG_MOD R9A07G054_WDT1_CLK>;
+			clock-names = "pclk", "oscclk";
+			interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "wdt", "perrout";
+			resets = <&cpg R9A07G054_WDT1_PRESETN>;
+			power-domains = <&cpg>;
+			status = "disabled";
+		};
+
+		wdt2: watchdog@12800400 {
+			compatible = "renesas,r9a07g054-wdt",
+				     "renesas,rzg2l-wdt";
+			reg = <0 0x12800400 0 0x400>;
+			clocks = <&cpg CPG_MOD R9A07G054_WDT2_PCLK>,
+				 <&cpg CPG_MOD R9A07G054_WDT2_CLK>;
+			clock-names = "pclk", "oscclk";
+			interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "wdt", "perrout";
+			resets = <&cpg R9A07G054_WDT2_PRESETN>;
+			power-domains = <&cpg>;
+			status = "disabled";
+		};
+
+		ostm0: timer@12801000 {
+			compatible = "renesas,r9a07g054-ostm",
+				     "renesas,ostm";
+			reg = <0x0 0x12801000 0x0 0x400>;
+			interrupts = <GIC_SPI 46 IRQ_TYPE_EDGE_RISING>;
+			clocks = <&cpg CPG_MOD R9A07G054_OSTM0_PCLK>;
+			resets = <&cpg R9A07G054_OSTM0_PRESETZ>;
+			power-domains = <&cpg>;
+			status = "disabled";
+		};
+
+		ostm1: timer@12801400 {
+			compatible = "renesas,r9a07g054-ostm",
+				     "renesas,ostm";
+			reg = <0x0 0x12801400 0x0 0x400>;
+			interrupts = <GIC_SPI 47 IRQ_TYPE_EDGE_RISING>;
+			clocks = <&cpg CPG_MOD R9A07G054_OSTM1_PCLK>;
+			resets = <&cpg R9A07G054_OSTM1_PRESETZ>;
+			power-domains = <&cpg>;
+			status = "disabled";
+		};
+
+		ostm2: timer@12801800 {
+			compatible = "renesas,r9a07g054-ostm",
+				     "renesas,ostm";
+			reg = <0x0 0x12801800 0x0 0x400>;
+			interrupts = <GIC_SPI 48 IRQ_TYPE_EDGE_RISING>;
+			clocks = <&cpg CPG_MOD R9A07G054_OSTM2_PCLK>;
+			resets = <&cpg R9A07G054_OSTM2_PRESETZ>;
+			power-domains = <&cpg>;
+			status = "disabled";
+		};
+	};
+
+	thermal-zones {
+		cpu-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+			thermal-sensors = <&tsu 0>;
+			sustainable-power = <717>;
+
+			cooling-maps {
+				map0 {
+					trip = <&target>;
+					cooling-device = <&cpu0 0 2>;
+					contribution = <1024>;
+				};
+			};
+
+			trips {
+				sensor_crit: sensor-crit {
+					temperature = <125000>;
+					hysteresis = <1000>;
+					type = "critical";
+				};
+
+				target: trip-point {
+					temperature = <100000>;
+					hysteresis = <1000>;
+					type = "passive";
+				};
+			};
+		};
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupts-extended = <&gic GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+				      <&gic GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+				      <&gic GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+				      <&gic GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>;
+	};
+};
diff --git a/arch/arm64/boot/dts/renesas/r9a07g054l1.dtsi b/arch/arm64/boot/dts/renesas/r9a07g054l1.dtsi
new file mode 100644
index 000000000000..c448cc6634c1
--- /dev/null
+++ b/arch/arm64/boot/dts/renesas/r9a07g054l1.dtsi
@@ -0,0 +1,25 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+/*
+ * Device Tree Source for the RZ/V2L R9A07G054L1 SoC specific parts
+ *
+ * Copyright (C) 2021 Renesas Electronics Corp.
+ */
+
+/dts-v1/;
+#include "r9a07g054.dtsi"
+
+/ {
+	compatible = "renesas,r9a07g054l1", "renesas,r9a07g054";
+
+	cpus {
+		/delete-node/ cpu-map;
+		/delete-node/ cpu@100;
+	};
+
+	timer {
+		interrupts-extended = <&gic GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
+				      <&gic GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
+				      <&gic GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
+				      <&gic GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>;
+	};
+};
diff --git a/arch/arm64/boot/dts/renesas/r9a07g054l2-smarc.dts b/arch/arm64/boot/dts/renesas/r9a07g054l2-smarc.dts
new file mode 100644
index 000000000000..3d01a4cf0fbe
--- /dev/null
+++ b/arch/arm64/boot/dts/renesas/r9a07g054l2-smarc.dts
@@ -0,0 +1,18 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+/*
+ * Device Tree Source for the RZ/V2L SMARC EVK board
+ *
+ * Copyright (C) 2021 Renesas Electronics Corp.
+ */
+
+/dts-v1/;
+#include "r9a07g054l2.dtsi"
+#include "rzg2l-smarc-som.dtsi"
+#include "rzg2l-smarc-pinfunction.dtsi"
+#include "rz-smarc-common.dtsi"
+#include "rzg2l-smarc.dtsi"
+
+/ {
+	model = "Renesas SMARC EVK based on r9a07g054l2";
+	compatible = "renesas,smarc-evk", "renesas,r9a07g054l2", "renesas,r9a07g054";
+};
diff --git a/arch/arm64/boot/dts/renesas/r9a07g054l2.dtsi b/arch/arm64/boot/dts/renesas/r9a07g054l2.dtsi
new file mode 100644
index 000000000000..4d5914bc95d3
--- /dev/null
+++ b/arch/arm64/boot/dts/renesas/r9a07g054l2.dtsi
@@ -0,0 +1,13 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+/*
+ * Device Tree Source for the RZ/V2L R9A07G054L2 SoC specific parts
+ *
+ * Copyright (C) 2021 Renesas Electronics Corp.
+ */
+
+/dts-v1/;
+#include "r9a07g054.dtsi"
+
+/ {
+	compatible = "renesas,r9a07g054l2", "renesas,r9a07g054";
+};
diff --git a/arch/arm64/boot/dts/renesas/r9a09g011-v2mevk2.dts b/arch/arm64/boot/dts/renesas/r9a09g011-v2mevk2.dts
new file mode 100644
index 000000000000..5c15d73d059f
--- /dev/null
+++ b/arch/arm64/boot/dts/renesas/r9a09g011-v2mevk2.dts
@@ -0,0 +1,85 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+/*
+ * Device Tree Source for the RZ/V2M (r9a09g011) Evaluation Kit Board
+ *
+ * Copyright (C) 2022 Renesas Electronics Corp.
+ */
+
+/dts-v1/;
+#include "r9a09g011.dtsi"
+#include <dt-bindings/pinctrl/rzv2m-pinctrl.h>
+
+/ {
+	model = "RZ/V2M Evaluation Kit 2.0";
+	compatible = "renesas,rzv2mevk2", "renesas,r9a09g011";
+
+	aliases {
+		serial0 = &uart0;
+		ethernet0 = &avb;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@58000000 {
+		device_type = "memory";
+		/*
+		 * first 1.25GiB is reserved for ISP Firmware,
+		 * next 128MiB is reserved for secure area.
+		 */
+		reg = <0x0 0x58000000 0x0 0x28000000>;
+	};
+
+	memory@180000000 {
+		device_type = "memory";
+		reg = <0x1 0x80000000 0x0 0x80000000>;
+	};
+};
+
+&avb {
+	renesas,no-ether-link;
+	phy-handle = <&phy0>;
+	phy-mode = "gmii";
+	status = "okay";
+
+	phy0: ethernet-phy@0 {
+		compatible = "ethernet-phy-id001c.c916",
+			     "ethernet-phy-ieee802.3-c22";
+		reg = <0>;
+	};
+};
+
+&extal_clk {
+	clock-frequency = <48000000>;
+};
+
+&i2c0 {
+	pinctrl-0 = <&i2c0_pins>;
+	pinctrl-names = "default";
+	clock-frequency = <400000>;
+	status = "okay";
+};
+
+&i2c2 {
+	pinctrl-0 = <&i2c2_pins>;
+	pinctrl-names = "default";
+	clock-frequency = <100000>;
+	status = "okay";
+};
+
+&pinctrl {
+	i2c0_pins: i2c0 {
+		pinmux = <RZV2M_PORT_PINMUX(5, 0, 2)>, /* SDA */
+			 <RZV2M_PORT_PINMUX(5, 1, 2)>; /* SCL */
+	};
+
+	i2c2_pins: i2c2 {
+		pinmux = <RZV2M_PORT_PINMUX(3, 8, 2)>, /* SDA */
+			 <RZV2M_PORT_PINMUX(3, 9, 2)>; /* SCL */
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/renesas/r9a09g011.dtsi b/arch/arm64/boot/dts/renesas/r9a09g011.dtsi
new file mode 100644
index 000000000000..fb1a97202c38
--- /dev/null
+++ b/arch/arm64/boot/dts/renesas/r9a09g011.dtsi
@@ -0,0 +1,222 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+/*
+ * Device Tree Source for the RZ/V2M SoC
+ *
+ * Copyright (C) 2022 Renesas Electronics Corp.
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/r9a09g011-cpg.h>
+
+/ {
+	compatible = "renesas,r9a09g011";
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	/* clock can be either from exclk or crystal oscillator (XIN/XOUT) */
+	extal_clk: extal {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		/* This value must be overridden by the board */
+		clock-frequency = <0>;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu-map {
+			cluster0 {
+				core0 {
+					cpu = <&cpu0>;
+				};
+			};
+		};
+
+		cpu0: cpu@0 {
+			compatible = "arm,cortex-a53";
+			reg = <0>;
+			device_type = "cpu";
+			clocks = <&cpg CPG_MOD R9A09G011_CA53_CLK>;
+		};
+	};
+
+	soc: soc {
+		compatible = "simple-bus";
+		interrupt-parent = <&gic>;
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		gic: interrupt-controller@82000000 {
+			compatible = "arm,gic-400";
+			#interrupt-cells = <3>;
+			#address-cells = <0>;
+			interrupt-controller;
+			reg = <0x0 0x82010000 0 0x1000>,
+			      <0x0 0x82020000 0 0x20000>,
+			      <0x0 0x82040000 0 0x20000>,
+			      <0x0 0x82060000 0 0x20000>;
+			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_HIGH)>;
+			clocks = <&cpg CPG_MOD R9A09G011_GIC_CLK>;
+			clock-names = "clk";
+		};
+
+		avb: ethernet@a3300000 {
+			compatible = "renesas,etheravb-r9a09g011","renesas,etheravb-rzv2m";
+			reg = <0 0xa3300000 0 0x800>;
+			interrupts = <GIC_SPI 251 IRQ_TYPE_LEVEL_HIGH>, /* ch0: Rx0 BE */
+				     <GIC_SPI 252 IRQ_TYPE_LEVEL_HIGH>, /* ch1: Rx1 NC */
+				     <GIC_SPI 253 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 254 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 255 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 256 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 257 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 258 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 259 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 260 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 261 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 262 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 263 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 264 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 265 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 266 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 267 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 268 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 269 IRQ_TYPE_LEVEL_HIGH>, /* ch18: Tx0 BE */
+				     <GIC_SPI 270 IRQ_TYPE_LEVEL_HIGH>, /* ch19: Tx1 NC */
+				     <GIC_SPI 271 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 272 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 273 IRQ_TYPE_LEVEL_HIGH>, /* DiA */
+				     <GIC_SPI 274 IRQ_TYPE_LEVEL_HIGH>, /* DiB */
+				     <GIC_SPI 275 IRQ_TYPE_LEVEL_HIGH>, /* Line1_A */
+				     <GIC_SPI 276 IRQ_TYPE_LEVEL_HIGH>, /* Line1_B */
+				     <GIC_SPI 277 IRQ_TYPE_LEVEL_HIGH>, /* Line2_A */
+				     <GIC_SPI 278 IRQ_TYPE_LEVEL_HIGH>, /* Line2_B */
+				     <GIC_SPI 279 IRQ_TYPE_LEVEL_HIGH>; /* Line3 MAC */
+			interrupt-names = "ch0", "ch1", "ch2", "ch3",
+					  "ch4", "ch5", "ch6", "ch7",
+					  "ch8", "ch9", "ch10", "ch11",
+					  "ch12", "ch13", "ch14", "ch15",
+					  "ch16", "ch17", "ch18", "ch19",
+					  "ch20", "ch21", "dia", "dib",
+					  "err_a", "err_b", "mgmt_a", "mgmt_b",
+					  "line3";
+			clocks = <&cpg CPG_MOD R9A09G011_ETH0_CLK_AXI>,
+				 <&cpg CPG_MOD R9A09G011_ETH0_CLK_CHI>,
+				 <&cpg CPG_MOD R9A09G011_ETH0_GPTP_EXT>;
+			clock-names = "axi", "chi", "gptp";
+			resets = <&cpg R9A09G011_ETH0_RST_HW_N>;
+			power-domains = <&cpg>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disable";
+		};
+
+		cpg: clock-controller@a3500000 {
+			compatible = "renesas,r9a09g011-cpg";
+			reg = <0 0xa3500000 0 0x1000>;
+			clocks = <&extal_clk>;
+			clock-names = "extal";
+			#clock-cells = <2>;
+			#reset-cells = <1>;
+			#power-domain-cells = <0>;
+		};
+
+		i2c0: i2c@a4030000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "renesas,i2c-r9a09g011", "renesas,rzv2m-i2c";
+			reg = <0 0xa4030000 0 0x80>;
+			interrupts = <GIC_SPI 232 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 236 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "tia", "tis";
+			clocks = <&cpg CPG_MOD R9A09G011_IIC_PCLK0>;
+			resets = <&cpg R9A09G011_IIC_GPA_PRESETN>;
+			power-domains = <&cpg>;
+			status = "disabled";
+		};
+
+		i2c2: i2c@a4030100 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "renesas,i2c-r9a09g011", "renesas,rzv2m-i2c";
+			reg = <0 0xa4030100 0 0x80>;
+			interrupts = <GIC_SPI 234 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 238 IRQ_TYPE_EDGE_RISING>;
+			interrupt-names = "tia", "tis";
+			clocks = <&cpg CPG_MOD R9A09G011_IIC_PCLK1>;
+			resets = <&cpg R9A09G011_IIC_GPB_PRESETN>;
+			power-domains = <&cpg>;
+			status = "disabled";
+		};
+
+		uart0: serial@a4040000 {
+			compatible = "renesas,r9a09g011-uart", "renesas,em-uart";
+			reg = <0 0xa4040000 0 0x80>;
+			interrupts = <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD R9A09G011_URT0_CLK>,
+				 <&cpg CPG_MOD R9A09G011_URT_PCLK>;
+			clock-names = "sclk", "pclk";
+			status = "disabled";
+		};
+
+		pinctrl: pinctrl@b6250000 {
+			compatible = "renesas,r9a09g011-pinctrl";
+			reg = <0 0xb6250000 0 0x800>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			gpio-ranges = <&pinctrl 0 0 352>;
+			interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&cpg CPG_MOD R9A09G011_PFC_PCLK>;
+			power-domains = <&cpg>;
+			resets = <&cpg R9A09G011_PFC_PRESETN>;
+		};
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupts-extended = <&gic GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
+				      <&gic GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
+				      <&gic GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>,
+				      <&gic GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(1) | IRQ_TYPE_LEVEL_LOW)>;
+	};
+};
diff --git a/arch/arm64/boot/dts/renesas/rz-smarc-common.dtsi b/arch/arm64/boot/dts/renesas/rz-smarc-common.dtsi
new file mode 100644
index 000000000000..3962d47b3e59
--- /dev/null
+++ b/arch/arm64/boot/dts/renesas/rz-smarc-common.dtsi
@@ -0,0 +1,183 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+/*
+ * Device Tree Source for the RZ/{G2L,G2LC,V2L} SMARC EVK common parts
+ *
+ * Copyright (C) 2022 Renesas Electronics Corp.
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/rzg2l-pinctrl.h>
+
+/*
+ * SSI-WM8978
+ *
+ * This command is required when Playback/Capture
+ *
+ *	amixer cset name='Left Input Mixer L2 Switch' on
+ *	amixer cset name='Right Input Mixer R2 Switch' on
+ *	amixer cset name='Headphone Playback Volume' 100
+ *	amixer cset name='PCM Volume' 100%
+ *	amixer cset name='Input PGA Volume' 25
+ *
+ */
+
+/ {
+	aliases {
+		serial0 = &scif0;
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	audio_mclock: audio_mclock {
+		compatible = "fixed-clock";
+		#clock-cells = <0>;
+		clock-frequency = <11289600>;
+	};
+
+	snd_rzg2l: sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,format = "i2s";
+		simple-audio-card,bitclock-master = <&cpu_dai>;
+		simple-audio-card,frame-master = <&cpu_dai>;
+		simple-audio-card,mclk-fs = <256>;
+
+		simple-audio-card,widgets = "Microphone", "Microphone Jack";
+		simple-audio-card,routing =
+			    "L2", "Mic Bias",
+			    "R2", "Mic Bias",
+			    "Mic Bias", "Microphone Jack";
+
+		cpu_dai: simple-audio-card,cpu {
+		};
+
+		codec_dai: simple-audio-card,codec {
+			clocks = <&audio_mclock>;
+			sound-dai = <&wm8978>;
+		};
+	};
+
+	usb0_vbus_otg: regulator-usb0-vbus-otg {
+		compatible = "regulator-fixed";
+
+		regulator-name = "USB0_VBUS_OTG";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	vccq_sdhi1: regulator-vccq-sdhi1 {
+		compatible = "regulator-gpio";
+		regulator-name = "SDHI1 VccQ";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+		gpios-states = <1>;
+		states = <3300000 1>, <1800000 0>;
+	};
+};
+
+&audio_clk1{
+	clock-frequency = <11289600>;
+};
+
+&audio_clk2{
+	clock-frequency = <12288000>;
+};
+
+&canfd {
+	pinctrl-0 = <&can0_pins &can1_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	channel0 {
+		status = "okay";
+	};
+
+	channel1 {
+		status = "okay";
+	};
+};
+
+&ehci0 {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&hsusb {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&i2c0 {
+	pinctrl-0 = <&i2c0_pins>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&i2c1 {
+	pinctrl-0 = <&i2c1_pins>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&ohci0 {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&phyrst {
+	status = "okay";
+};
+
+&scif0 {
+	pinctrl-0 = <&scif0_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&sdhi1 {
+	pinctrl-0 = <&sdhi1_pins>;
+	pinctrl-1 = <&sdhi1_pins_uhs>;
+	pinctrl-names = "default", "state_uhs";
+
+	vmmc-supply = <&reg_3p3v>;
+	vqmmc-supply = <&vccq_sdhi1>;
+	bus-width = <4>;
+	sd-uhs-sdr50;
+	sd-uhs-sdr104;
+	status = "okay";
+};
+
+&spi1 {
+	pinctrl-0 = <&spi1_pins>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&usb2_phy0 {
+	pinctrl-0 = <&usb0_pins>;
+	pinctrl-names = "default";
+
+	vbus-supply = <&usb0_vbus_otg>;
+	status = "okay";
+};
+
+&usb2_phy1 {
+	pinctrl-0 = <&usb1_pins>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/renesas/rzg2l-smarc-pinfunction.dtsi b/arch/arm64/boot/dts/renesas/rzg2l-smarc-pinfunction.dtsi
new file mode 100644
index 000000000000..9085d8c76ce1
--- /dev/null
+++ b/arch/arm64/boot/dts/renesas/rzg2l-smarc-pinfunction.dtsi
@@ -0,0 +1,137 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+/*
+ * Device Tree Source for the RZ/{G2L,V2L} SMARC pincontrol parts
+ *
+ * Copyright (C) 2021 Renesas Electronics Corp.
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/rzg2l-pinctrl.h>
+
+&pinctrl {
+	pinctrl-0 = <&sound_clk_pins>;
+	pinctrl-names = "default";
+
+	can0_pins: can0 {
+		pinmux = <RZG2L_PORT_PINMUX(10, 1, 2)>, /* TX */
+			 <RZG2L_PORT_PINMUX(11, 0, 2)>; /* RX */
+	};
+
+	/* SW7 should be at position 2->3 so that GPIO8_CAN0_STB line is activated */
+	can0-stb-hog {
+		gpio-hog;
+		gpios = <RZG2L_GPIO(42, 2) GPIO_ACTIVE_HIGH>;
+		output-low;
+		line-name = "can0_stb";
+	};
+
+	can1_pins: can1 {
+		pinmux = <RZG2L_PORT_PINMUX(12, 1, 2)>, /* TX */
+			 <RZG2L_PORT_PINMUX(13, 0, 2)>; /* RX */
+	};
+
+	/* SW8 should be at position 2->3 so that GPIO9_CAN1_STB line is activated */
+	can1-stb-hog {
+		gpio-hog;
+		gpios = <RZG2L_GPIO(42, 3) GPIO_ACTIVE_HIGH>;
+		output-low;
+		line-name = "can1_stb";
+	};
+
+	i2c0_pins: i2c0 {
+		pins = "RIIC0_SDA", "RIIC0_SCL";
+		input-enable;
+	};
+
+	i2c1_pins: i2c1 {
+		pins = "RIIC1_SDA", "RIIC1_SCL";
+		input-enable;
+	};
+
+	i2c3_pins: i2c3 {
+		pinmux = <RZG2L_PORT_PINMUX(18, 0, 3)>, /* SDA */
+			 <RZG2L_PORT_PINMUX(18, 1, 3)>; /* SCL */
+	};
+
+	scif0_pins: scif0 {
+		pinmux = <RZG2L_PORT_PINMUX(38, 0, 1)>,	/* TxD */
+			 <RZG2L_PORT_PINMUX(38, 1, 1)>;	/* RxD */
+	};
+
+	scif2_pins: scif2 {
+		pinmux = <RZG2L_PORT_PINMUX(48, 0, 1)>, /* TxD */
+			 <RZG2L_PORT_PINMUX(48, 1, 1)>, /* RxD */
+			 <RZG2L_PORT_PINMUX(48, 3, 1)>, /* CTS# */
+			 <RZG2L_PORT_PINMUX(48, 4, 1)>; /* RTS# */
+	};
+
+	sd1-pwr-en-hog {
+		gpio-hog;
+		gpios = <RZG2L_GPIO(39, 2) GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "sd1_pwr_en";
+	};
+
+	sdhi1_pins: sd1 {
+		sd1_data {
+			pins = "SD1_DATA0", "SD1_DATA1", "SD1_DATA2", "SD1_DATA3";
+			power-source = <3300>;
+		};
+
+		sd1_ctrl {
+			pins = "SD1_CLK", "SD1_CMD";
+			power-source = <3300>;
+		};
+
+		sd1_mux {
+			pinmux = <RZG2L_PORT_PINMUX(19, 0, 1)>; /* SD1_CD */
+		};
+	};
+
+	sdhi1_pins_uhs: sd1_uhs {
+		sd1_data_uhs {
+			pins = "SD1_DATA0", "SD1_DATA1", "SD1_DATA2", "SD1_DATA3";
+			power-source = <1800>;
+		};
+
+		sd1_ctrl_uhs {
+			pins = "SD1_CLK", "SD1_CMD";
+			power-source = <1800>;
+		};
+
+		sd1_mux_uhs {
+			pinmux = <RZG2L_PORT_PINMUX(19, 0, 1)>; /* SD1_CD */
+		};
+	};
+
+	sound_clk_pins: sound_clk {
+		pins = "AUDIO_CLK1", "AUDIO_CLK2";
+		input-enable;
+	};
+
+	spi1_pins: spi1 {
+		pinmux = <RZG2L_PORT_PINMUX(44, 0, 1)>, /* CK */
+			 <RZG2L_PORT_PINMUX(44, 1, 1)>, /* MOSI */
+			 <RZG2L_PORT_PINMUX(44, 2, 1)>, /* MISO */
+			 <RZG2L_PORT_PINMUX(44, 3, 1)>; /* SSL */
+	};
+
+	ssi0_pins: ssi0 {
+		pinmux = <RZG2L_PORT_PINMUX(45, 0, 1)>, /* BCK */
+			 <RZG2L_PORT_PINMUX(45, 1, 1)>, /* RCK */
+			 <RZG2L_PORT_PINMUX(45, 2, 1)>, /* TXD */
+			 <RZG2L_PORT_PINMUX(45, 3, 1)>; /* RXD */
+	};
+
+	usb0_pins: usb0 {
+		pinmux = <RZG2L_PORT_PINMUX(4, 0, 1)>, /* VBUS */
+			 <RZG2L_PORT_PINMUX(5, 0, 1)>, /* OVC */
+			 <RZG2L_PORT_PINMUX(5, 1, 1)>; /* OTG_ID */
+	};
+
+	usb1_pins: usb1 {
+		pinmux = <RZG2L_PORT_PINMUX(42, 0, 1)>, /* VBUS */
+			 <RZG2L_PORT_PINMUX(42, 1, 1)>; /* OVC */
+	};
+};
+
diff --git a/arch/arm64/boot/dts/renesas/rzg2l-smarc-som.dtsi b/arch/arm64/boot/dts/renesas/rzg2l-smarc-som.dtsi
index 7e84a29dddfa..c4faff092380 100644
--- a/arch/arm64/boot/dts/renesas/rzg2l-smarc-som.dtsi
+++ b/arch/arm64/boot/dts/renesas/rzg2l-smarc-som.dtsi
@@ -1,11 +1,12 @@
 // SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
 /*
- * Device Tree Source for the RZ/G2L SMARC SOM common parts
+ * Device Tree Source for the RZ/{G2L,V2L} SMARC SOM common parts
  *
  * Copyright (C) 2021 Renesas Electronics Corp.
  */
 
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irqc-rzg2l.h>
 #include <dt-bindings/pinctrl/rzg2l-pinctrl.h>
 
 /* SW1[2] should be at position 2/OFF to enable 64 GB eMMC */
@@ -34,7 +35,7 @@
 		reg = <0x0 0x48000000 0x0 0x78000000>;
 	};
 
-	reg_1p8v: regulator0 {
+	reg_1p8v: regulator-1p8v {
 		compatible = "regulator-fixed";
 		regulator-name = "fixed-1.8V";
 		regulator-min-microvolt = <1800000>;
@@ -43,7 +44,7 @@
 		regulator-always-on;
 	};
 
-	reg_3p3v: regulator1 {
+	reg_3p3v: regulator-3p3v {
 		compatible = "regulator-fixed";
 		regulator-name = "fixed-3.3V";
 		regulator-min-microvolt = <3300000>;
@@ -52,6 +53,15 @@
 		regulator-always-on;
 	};
 
+	reg_1p1v: regulator-vdd-core {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-1.1V";
+		regulator-min-microvolt = <1100000>;
+		regulator-max-microvolt = <1100000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
 	vccq_sdhi0: regulator-vccq-sdhi0 {
 		compatible = "regulator-gpio";
 
@@ -85,6 +95,8 @@
 		compatible = "ethernet-phy-id0022.1640",
 			     "ethernet-phy-ieee802.3-c22";
 		reg = <7>;
+		interrupt-parent = <&irqc>;
+		interrupts = <RZG2L_IRQ2 IRQ_TYPE_LEVEL_LOW>;
 		rxc-skew-psec = <2400>;
 		txc-skew-psec = <2400>;
 		rxdv-skew-psec = <0>;
@@ -111,6 +123,8 @@
 		compatible = "ethernet-phy-id0022.1640",
 			     "ethernet-phy-ieee802.3-c22";
 		reg = <7>;
+		interrupt-parent = <&irqc>;
+		interrupts = <RZG2L_IRQ3 IRQ_TYPE_LEVEL_LOW>;
 		rxc-skew-psec = <2400>;
 		txc-skew-psec = <2400>;
 		rxdv-skew-psec = <0>;
@@ -130,6 +144,18 @@
 	clock-frequency = <24000000>;
 };
 
+&gpu {
+	mali-supply = <&reg_1p1v>;
+};
+
+&ostm1 {
+	status = "okay";
+};
+
+&ostm2 {
+	status = "okay";
+};
+
 &pinctrl {
 	adc_pins: adc {
 		pinmux = <RZG2L_PORT_PINMUX(9, 0, 2)>; /* ADC_TRG */
@@ -150,7 +176,8 @@
 			 <RZG2L_PORT_PINMUX(25, 0, 1)>, /* ET0_RXD0 */
 			 <RZG2L_PORT_PINMUX(25, 1, 1)>, /* ET0_RXD1 */
 			 <RZG2L_PORT_PINMUX(26, 0, 1)>, /* ET0_RXD2 */
-			 <RZG2L_PORT_PINMUX(26, 1, 1)>; /* ET0_RXD3 */
+			 <RZG2L_PORT_PINMUX(26, 1, 1)>, /* ET0_RXD3 */
+			 <RZG2L_PORT_PINMUX(1, 0, 1)>;  /* IRQ2 */
 	};
 
 	eth1_pins: eth1 {
@@ -168,7 +195,8 @@
 			 <RZG2L_PORT_PINMUX(34, 1, 1)>, /* ET1_RXD0 */
 			 <RZG2L_PORT_PINMUX(35, 0, 1)>, /* ET1_RXD1 */
 			 <RZG2L_PORT_PINMUX(35, 1, 1)>, /* ET1_RXD2 */
-			 <RZG2L_PORT_PINMUX(36, 0, 1)>; /* ET1_RXD3 */
+			 <RZG2L_PORT_PINMUX(36, 0, 1)>, /* ET1_RXD3 */
+			 <RZG2L_PORT_PINMUX(1, 1, 1)>;  /* IRQ3 */
 	};
 
 	gpio-sd0-pwr-en-hog {
@@ -178,6 +206,18 @@
 		line-name = "gpio_sd0_pwr_en";
 	};
 
+	qspi0_pins: qspi0 {
+		qspi0-data {
+			pins = "QSPI0_IO0", "QSPI0_IO1", "QSPI0_IO2", "QSPI0_IO3";
+			power-source = <1800>;
+		};
+
+		qspi0-ctrl {
+			pins = "QSPI0_SPCLK", "QSPI0_SSL", "QSPI_RESET#";
+			power-source = <1800>;
+		};
+	};
+
 	/*
 	 * SD0 device selection is XOR between GPIO_SD0_DEV_SEL and SW1[2]
 	 * The below switch logic can be used to select the device between
@@ -243,6 +283,34 @@
 	};
 };
 
+&sbc {
+	pinctrl-0 = <&qspi0_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	flash@0 {
+		compatible = "micron,mt25qu512a", "jedec,spi-nor";
+		reg = <0>;
+		m25p,fast-read;
+		spi-max-frequency = <50000000>;
+		spi-rx-bus-width = <4>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			boot@0 {
+				reg = <0x00000000 0x2000000>;
+				read-only;
+			};
+			user@2000000 {
+				reg = <0x2000000 0x2000000>;
+			};
+		};
+	};
+};
+
 #if SDHI
 &sdhi0 {
 	pinctrl-0 = <&sdhi0_pins>;
@@ -273,3 +341,18 @@
 	status = "okay";
 };
 #endif
+
+&wdt0 {
+	status = "okay";
+	timeout-sec = <60>;
+};
+
+&wdt1 {
+	status = "okay";
+	timeout-sec = <60>;
+};
+
+&wdt2 {
+	status = "okay";
+	timeout-sec = <60>;
+};
diff --git a/arch/arm64/boot/dts/renesas/rzg2l-smarc.dtsi b/arch/arm64/boot/dts/renesas/rzg2l-smarc.dtsi
index 2863e487a640..e180a955b6ac 100644
--- a/arch/arm64/boot/dts/renesas/rzg2l-smarc.dtsi
+++ b/arch/arm64/boot/dts/renesas/rzg2l-smarc.dtsi
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
 /*
- * Device Tree Source for the RZ/G2L SMARC EVK common parts
+ * Device Tree Source for the RZ/{G2L,V2L} SMARC EVK common parts
  *
  * Copyright (C) 2021 Renesas Electronics Corp.
  */
@@ -8,127 +8,18 @@
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/pinctrl/rzg2l-pinctrl.h>
 
-/*
- * SSI-WM8978
- *
- * This command is required when Playback/Capture
- *
- *	amixer cset name='Left Input Mixer L2 Switch' on
- *	amixer cset name='Right Input Mixer R2 Switch' on
- *	amixer cset name='Headphone Playback Volume' 100
- *	amixer cset name='PCM Volume' 100%
- *	amixer cset name='Input PGA Volume' 25
- *
- */
+/* comment the #define statement to disable SCIF2 (SER0) on PMOD1 (CN7) */
+#define PMOD1_SER0	1
 
 / {
 	aliases {
-		serial0 = &scif0;
-		i2c0 = &i2c0;
-		i2c1 = &i2c1;
+		serial1 = &scif2;
 		i2c3 = &i2c3;
 	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	audio_mclock: audio_mclock {
-		compatible = "fixed-clock";
-		#clock-cells = <0>;
-		clock-frequency = <11289600>;
-	};
-
-	snd_rzg2l: sound {
-		compatible = "simple-audio-card";
-		simple-audio-card,format = "i2s";
-		simple-audio-card,bitclock-master = <&cpu_dai>;
-		simple-audio-card,frame-master = <&cpu_dai>;
-		simple-audio-card,mclk-fs = <256>;
-
-		simple-audio-card,widgets = "Microphone", "Microphone Jack";
-		simple-audio-card,routing =
-			    "L2", "Mic Bias",
-			    "R2", "Mic Bias",
-			    "Mic Bias", "Microphone Jack";
-
-		cpu_dai: simple-audio-card,cpu {
-			sound-dai = <&ssi0>;
-		};
-
-		codec_dai: simple-audio-card,codec {
-			clocks = <&audio_mclock>;
-			sound-dai = <&wm8978>;
-		};
-	};
-
-	usb0_vbus_otg: regulator-usb0-vbus-otg {
-		compatible = "regulator-fixed";
-
-		regulator-name = "USB0_VBUS_OTG";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-	};
-
-	vccq_sdhi1: regulator-vccq-sdhi1 {
-		compatible = "regulator-gpio";
-		regulator-name = "SDHI1 VccQ";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <3300000>;
-		gpios = <&pinctrl RZG2L_GPIO(39, 1) GPIO_ACTIVE_HIGH>;
-		gpios-states = <1>;
-		states = <3300000 1>, <1800000 0>;
-	};
-};
-
-&audio_clk1{
-	clock-frequency = <11289600>;
-};
-
-&audio_clk2{
-	clock-frequency = <12288000>;
-};
-
-&canfd {
-	pinctrl-0 = <&can0_pins &can1_pins>;
-	pinctrl-names = "default";
-	status = "okay";
-
-	channel0 {
-		status = "okay";
-	};
-
-	channel1 {
-		status = "okay";
-	};
-};
-
-&ehci0 {
-	dr_mode = "otg";
-	status = "okay";
 };
 
-&ehci1 {
-	status = "okay";
-};
-
-&hsusb {
-	dr_mode = "otg";
-	status = "okay";
-};
-
-&i2c0 {
-	pinctrl-0 = <&i2c0_pins>;
-	pinctrl-names = "default";
-
-	status = "okay";
-};
-
-&i2c1 {
-	pinctrl-0 = <&i2c1_pins>;
-	pinctrl-names = "default";
-
-	status = "okay";
+&cpu_dai {
+	sound-dai = <&ssi0>;
 };
 
 &i2c3 {
@@ -145,150 +36,22 @@
 	};
 };
 
-&ohci0 {
-	dr_mode = "otg";
-	status = "okay";
-};
-
-&ohci1 {
-	status = "okay";
-};
-
-&phyrst {
-	status = "okay";
-};
-
-&pinctrl {
-	pinctrl-0 = <&sound_clk_pins>;
-	pinctrl-names = "default";
-
-	can0_pins: can0 {
-		pinmux = <RZG2L_PORT_PINMUX(10, 1, 2)>, /* TX */
-			 <RZG2L_PORT_PINMUX(11, 0, 2)>; /* RX */
-	};
-
-	/* SW7 should be at position 2->3 so that GPIO8_CAN0_STB line is activated */
-	can0-stb {
-		gpio-hog;
-		gpios = <RZG2L_GPIO(42, 2) GPIO_ACTIVE_HIGH>;
-		output-low;
-		line-name = "can0_stb";
-	};
-
-	can1_pins: can1 {
-		pinmux = <RZG2L_PORT_PINMUX(12, 1, 2)>, /* TX */
-			 <RZG2L_PORT_PINMUX(13, 0, 2)>; /* RX */
-	};
-
-	/* SW8 should be at position 2->3 so that GPIO9_CAN1_STB line is activated */
-	can1-stb {
-		gpio-hog;
-		gpios = <RZG2L_GPIO(42, 3) GPIO_ACTIVE_HIGH>;
-		output-low;
-		line-name = "can1_stb";
-	};
-
-	i2c0_pins: i2c0 {
-		pins = "RIIC0_SDA", "RIIC0_SCL";
-		input-enable;
-	};
-
-	i2c1_pins: i2c1 {
-		pins = "RIIC1_SDA", "RIIC1_SCL";
-		input-enable;
-	};
-
-	i2c3_pins: i2c3 {
-		pinmux = <RZG2L_PORT_PINMUX(18, 0, 3)>, /* SDA */
-			 <RZG2L_PORT_PINMUX(18, 1, 3)>; /* SCL */
-	};
-
-	scif0_pins: scif0 {
-		pinmux = <RZG2L_PORT_PINMUX(38, 0, 1)>,	/* TxD */
-			 <RZG2L_PORT_PINMUX(38, 1, 1)>;	/* RxD */
-	};
-
-	sd1-pwr-en-hog {
-		gpio-hog;
-		gpios = <RZG2L_GPIO(39, 2) GPIO_ACTIVE_HIGH>;
-		output-high;
-		line-name = "sd1_pwr_en";
-	};
-
-	sdhi1_pins: sd1 {
-		sd1_data {
-			pins = "SD1_DATA0", "SD1_DATA1", "SD1_DATA2", "SD1_DATA3";
-			power-source = <3300>;
-		};
-
-		sd1_ctrl {
-			pins = "SD1_CLK", "SD1_CMD";
-			power-source = <3300>;
-		};
-
-		sd1_mux {
-			pinmux = <RZG2L_PORT_PINMUX(19, 0, 1)>; /* SD1_CD */
-		};
-	};
-
-	sdhi1_pins_uhs: sd1_uhs {
-		sd1_data_uhs {
-			pins = "SD1_DATA0", "SD1_DATA1", "SD1_DATA2", "SD1_DATA3";
-			power-source = <1800>;
-		};
-
-		sd1_ctrl_uhs {
-			pins = "SD1_CLK", "SD1_CMD";
-			power-source = <1800>;
-		};
-
-		sd1_mux_uhs {
-			pinmux = <RZG2L_PORT_PINMUX(19, 0, 1)>; /* SD1_CD */
-		};
-	};
-
-	sound_clk_pins: sound_clk {
-		pins = "AUDIO_CLK1", "AUDIO_CLK2";
-		input-enable;
-	};
-
-	ssi0_pins: ssi0 {
-		pinmux = <RZG2L_PORT_PINMUX(45, 0, 1)>, /* BCK */
-			 <RZG2L_PORT_PINMUX(45, 1, 1)>, /* RCK */
-			 <RZG2L_PORT_PINMUX(45, 2, 1)>, /* TXD */
-			 <RZG2L_PORT_PINMUX(45, 3, 1)>; /* RXD */
-	};
-
-	usb0_pins: usb0 {
-		pinmux = <RZG2L_PORT_PINMUX(4, 0, 1)>, /* VBUS */
-			 <RZG2L_PORT_PINMUX(5, 0, 1)>, /* OVC */
-			 <RZG2L_PORT_PINMUX(5, 1, 1)>; /* OTG_ID */
-	};
-
-	usb1_pins: usb1 {
-		pinmux = <RZG2L_PORT_PINMUX(42, 0, 1)>, /* VBUS */
-			 <RZG2L_PORT_PINMUX(42, 1, 1)>; /* OVC */
-	};
-};
-
-&scif0 {
-	pinctrl-0 = <&scif0_pins>;
+/*
+ * To enable SCIF2 (SER0) on PMOD1 (CN7)
+ * SW1 should be at position 2->3 so that SER0_CTS# line is activated
+ * SW2 should be at position 2->3 so that SER0_TX line is activated
+ * SW3 should be at position 2->3 so that SER0_RX line is activated
+ * SW4 should be at position 2->3 so that SER0_RTS# line is activated
+ */
+#if PMOD1_SER0
+&scif2 {
+	pinctrl-0 = <&scif2_pins>;
 	pinctrl-names = "default";
-	status = "okay";
-};
 
-&sdhi1 {
-	pinctrl-0 = <&sdhi1_pins>;
-	pinctrl-1 = <&sdhi1_pins_uhs>;
-	pinctrl-names = "default", "state_uhs";
-
-	vmmc-supply = <&reg_3p3v>;
-	vqmmc-supply = <&vccq_sdhi1>;
-	bus-width = <4>;
-	sd-uhs-sdr50;
-	sd-uhs-sdr104;
+	uart-has-rtscts;
 	status = "okay";
 };
+#endif
 
 &ssi0 {
 	pinctrl-0 = <&ssi0_pins>;
@@ -297,17 +60,6 @@
 	status = "okay";
 };
 
-&usb2_phy0 {
-	pinctrl-0 = <&usb0_pins>;
-	pinctrl-names = "default";
-
-	vbus-supply = <&usb0_vbus_otg>;
-	status = "okay";
-};
-
-&usb2_phy1 {
-	pinctrl-0 = <&usb1_pins>;
-	pinctrl-names = "default";
-
-	status = "okay";
+&vccq_sdhi1 {
+	gpios = <&pinctrl RZG2L_GPIO(39, 1) GPIO_ACTIVE_HIGH>;
 };
diff --git a/arch/arm64/boot/dts/renesas/rzg2lc-smarc-pinfunction.dtsi b/arch/arm64/boot/dts/renesas/rzg2lc-smarc-pinfunction.dtsi
new file mode 100644
index 000000000000..a78a8def363e
--- /dev/null
+++ b/arch/arm64/boot/dts/renesas/rzg2lc-smarc-pinfunction.dtsi
@@ -0,0 +1,134 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+/*
+ * Device Tree Source for the RZ/G2LC SMARC pincontrol parts
+ *
+ * Copyright (C) 2021 Renesas Electronics Corp.
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/rzg2l-pinctrl.h>
+
+&pinctrl {
+	pinctrl-0 = <&sound_clk_pins>;
+	pinctrl-names = "default";
+
+#if SW_SCIF_CAN
+	/* SW8 should be at position 2->1 */
+	can1_pins: can1 {
+		pinmux = <RZG2L_PORT_PINMUX(40, 0, 3)>, /* TxD */
+			 <RZG2L_PORT_PINMUX(40, 1, 3)>; /* RxD */
+	};
+#endif
+
+#if SW_RSPI_CAN
+	/* SW8 should be at position 2->3 so that GPIO9_CAN1_STB line is activated */
+	can1-stb-hog {
+		gpio-hog;
+		gpios = <RZG2L_GPIO(44, 3) GPIO_ACTIVE_HIGH>;
+		output-low;
+		line-name = "can1_stb";
+	};
+
+	can1_pins: can1 {
+		pinmux = <RZG2L_PORT_PINMUX(44, 0, 3)>, /* TxD */
+			 <RZG2L_PORT_PINMUX(44, 1, 3)>; /* RxD */
+	};
+#endif
+
+	i2c0_pins: i2c0 {
+		pins = "RIIC0_SDA", "RIIC0_SCL";
+		input-enable;
+	};
+
+	i2c1_pins: i2c1 {
+		pins = "RIIC1_SDA", "RIIC1_SCL";
+		input-enable;
+	};
+
+	i2c2_pins: i2c2 {
+		pinmux = <RZG2L_PORT_PINMUX(42, 3, 1)>, /* SDA */
+			 <RZG2L_PORT_PINMUX(42, 4, 1)>; /* SCL */
+	};
+
+	scif0_pins: scif0 {
+		pinmux = <RZG2L_PORT_PINMUX(38, 0, 1)>,	/* TxD */
+			 <RZG2L_PORT_PINMUX(38, 1, 1)>;	/* RxD */
+	};
+
+	scif1_pins: scif1 {
+		pinmux = <RZG2L_PORT_PINMUX(40, 0, 1)>, /* TxD */
+			 <RZG2L_PORT_PINMUX(40, 1, 1)>, /* RxD */
+			 <RZG2L_PORT_PINMUX(41, 0, 1)>, /* CTS# */
+			 <RZG2L_PORT_PINMUX(41, 1, 1)>; /* RTS# */
+	};
+
+	sd1-pwr-en-hog {
+		gpio-hog;
+		gpios = <RZG2L_GPIO(39, 2) GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "sd1_pwr_en";
+	};
+
+	sdhi1_pins: sd1 {
+		sd1_data {
+			pins = "SD1_DATA0", "SD1_DATA1", "SD1_DATA2", "SD1_DATA3";
+			power-source = <3300>;
+		};
+
+		sd1_ctrl {
+			pins = "SD1_CLK", "SD1_CMD";
+			power-source = <3300>;
+		};
+
+		sd1_mux {
+			pinmux = <RZG2L_PORT_PINMUX(19, 0, 1)>; /* SD1_CD */
+		};
+	};
+
+	sdhi1_pins_uhs: sd1_uhs {
+		sd1_data_uhs {
+			pins = "SD1_DATA0", "SD1_DATA1", "SD1_DATA2", "SD1_DATA3";
+			power-source = <1800>;
+		};
+
+		sd1_ctrl_uhs {
+			pins = "SD1_CLK", "SD1_CMD";
+			power-source = <1800>;
+		};
+
+		sd1_mux_uhs {
+			pinmux = <RZG2L_PORT_PINMUX(19, 0, 1)>; /* SD1_CD */
+		};
+	};
+
+	sound_clk_pins: sound_clk {
+		pins = "AUDIO_CLK1", "AUDIO_CLK2";
+		input-enable;
+	};
+
+	spi1_pins: spi1 {
+		pinmux = <RZG2L_PORT_PINMUX(44, 0, 1)>, /* CK */
+			 <RZG2L_PORT_PINMUX(44, 1, 1)>, /* MOSI */
+			 <RZG2L_PORT_PINMUX(44, 2, 1)>, /* MISO */
+			 <RZG2L_PORT_PINMUX(44, 3, 1)>; /* SSL */
+	};
+
+	ssi0_pins: ssi0 {
+		pinmux = <RZG2L_PORT_PINMUX(45, 0, 1)>, /* BCK */
+			 <RZG2L_PORT_PINMUX(45, 1, 1)>, /* RCK */
+			 <RZG2L_PORT_PINMUX(45, 2, 1)>, /* TXD */
+			 <RZG2L_PORT_PINMUX(45, 3, 1)>; /* RXD */
+	};
+
+	usb0_pins: usb0 {
+		pinmux = <RZG2L_PORT_PINMUX(4, 0, 1)>, /* VBUS */
+			 <RZG2L_PORT_PINMUX(5, 0, 1)>, /* OVC */
+			 <RZG2L_PORT_PINMUX(5, 1, 1)>; /* OTG_ID */
+	};
+
+	usb1_pins: usb1 {
+		pinmux = <RZG2L_PORT_PINMUX(42, 0, 1)>, /* VBUS */
+			 <RZG2L_PORT_PINMUX(42, 1, 1)>; /* OVC */
+	};
+};
+
diff --git a/arch/arm64/boot/dts/renesas/rzg2lc-smarc-som.dtsi b/arch/arm64/boot/dts/renesas/rzg2lc-smarc-som.dtsi
new file mode 100644
index 000000000000..78e6e2376b01
--- /dev/null
+++ b/arch/arm64/boot/dts/renesas/rzg2lc-smarc-som.dtsi
@@ -0,0 +1,283 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+/*
+ * Device Tree Source for the RZ/G2LC SMARC SOM common parts
+ *
+ * Copyright (C) 2021 Renesas Electronics Corp.
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/rzg2l-pinctrl.h>
+
+/ {
+	aliases {
+		ethernet0 = &eth0;
+	};
+
+	chosen {
+		bootargs = "ignore_loglevel rw root=/dev/nfs ip=on";
+	};
+
+	memory@48000000 {
+		device_type = "memory";
+		/* first 128MB is reserved for secure area. */
+		reg = <0x0 0x48000000 0x0 0x38000000>;
+	};
+
+	reg_1p8v: regulator-1p8v {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-1.8V";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-3.3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	reg_1p1v: regulator-vdd-core {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-1.1V";
+		regulator-min-microvolt = <1100000>;
+		regulator-max-microvolt = <1100000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	vccq_sdhi0: regulator-vccq-sdhi0 {
+		compatible = "regulator-gpio";
+
+		regulator-name = "SDHI0 VccQ";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+		states = <3300000 1>, <1800000 0>;
+		regulator-boot-on;
+		gpios = <&pinctrl RZG2L_GPIO(39, 0) GPIO_ACTIVE_HIGH>;
+		regulator-always-on;
+	};
+};
+
+&eth0 {
+	pinctrl-0 = <&eth0_pins>;
+	pinctrl-names = "default";
+	phy-handle = <&phy0>;
+	phy-mode = "rgmii-id";
+	status = "okay";
+
+	phy0: ethernet-phy@7 {
+		compatible = "ethernet-phy-id0022.1640",
+			     "ethernet-phy-ieee802.3-c22";
+		reg = <7>;
+		rxc-skew-psec = <2400>;
+		txc-skew-psec = <2400>;
+		rxdv-skew-psec = <0>;
+		txdv-skew-psec = <0>;
+		rxd0-skew-psec = <0>;
+		rxd1-skew-psec = <0>;
+		rxd2-skew-psec = <0>;
+		rxd3-skew-psec = <0>;
+		txd0-skew-psec = <0>;
+		txd1-skew-psec = <0>;
+		txd2-skew-psec = <0>;
+		txd3-skew-psec = <0>;
+	};
+};
+
+&extal_clk {
+	clock-frequency = <24000000>;
+};
+
+&gpu {
+	mali-supply = <&reg_1p1v>;
+};
+
+&ostm1 {
+	status = "okay";
+};
+
+&ostm2 {
+	status = "okay";
+};
+
+&pinctrl {
+	eth0_pins: eth0 {
+		pinmux = <RZG2L_PORT_PINMUX(28, 1, 1)>, /* ET0_LINKSTA */
+			 <RZG2L_PORT_PINMUX(27, 1, 1)>, /* ET0_MDC */
+			 <RZG2L_PORT_PINMUX(28, 0, 1)>, /* ET0_MDIO */
+			 <RZG2L_PORT_PINMUX(20, 0, 1)>, /* ET0_TXC */
+			 <RZG2L_PORT_PINMUX(20, 1, 1)>, /* ET0_TX_CTL */
+			 <RZG2L_PORT_PINMUX(20, 2, 1)>, /* ET0_TXD0 */
+			 <RZG2L_PORT_PINMUX(21, 0, 1)>, /* ET0_TXD1 */
+			 <RZG2L_PORT_PINMUX(21, 1, 1)>, /* ET0_TXD2 */
+			 <RZG2L_PORT_PINMUX(22, 0, 1)>, /* ET0_TXD3 */
+			 <RZG2L_PORT_PINMUX(24, 0, 1)>, /* ET0_RXC */
+			 <RZG2L_PORT_PINMUX(24, 1, 1)>, /* ET0_RX_CTL */
+			 <RZG2L_PORT_PINMUX(25, 0, 1)>, /* ET0_RXD0 */
+			 <RZG2L_PORT_PINMUX(25, 1, 1)>, /* ET0_RXD1 */
+			 <RZG2L_PORT_PINMUX(26, 0, 1)>, /* ET0_RXD2 */
+			 <RZG2L_PORT_PINMUX(26, 1, 1)>; /* ET0_RXD3 */
+	};
+
+	gpio-sd0-pwr-en-hog {
+		gpio-hog;
+		gpios = <RZG2L_GPIO(18, 1) GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "gpio_sd0_pwr_en";
+	};
+
+	qspi0_pins: qspi0 {
+		qspi0-data {
+			pins = "QSPI0_IO0", "QSPI0_IO1", "QSPI0_IO2", "QSPI0_IO3";
+			power-source = <1800>;
+		};
+
+		qspi0-ctrl {
+			pins = "QSPI0_SPCLK", "QSPI0_SSL", "QSPI_RESET#";
+			power-source = <1800>;
+		};
+	};
+
+	/*
+	 * SD0 device selection is XOR between GPIO_SD0_DEV_SEL and SW1[2]
+	 * The below switch logic can be used to select the device between
+	 * eMMC and microSD, after setting GPIO_SD0_DEV_SEL to high in DT.
+	 * SW1[2] should be at OFF position to enable 64 GB eMMC
+	 * SW1[2] should be at position ON to enable uSD card CN3
+	 */
+	gpio-sd0-dev-sel-hog {
+		gpio-hog;
+		gpios = <RZG2L_GPIO(40, 2) GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "gpio_sd0_dev_sel";
+	};
+
+	sdhi0_emmc_pins: sd0emmc {
+		sd0_emmc_data {
+			pins = "SD0_DATA0", "SD0_DATA1", "SD0_DATA2", "SD0_DATA3",
+			       "SD0_DATA4", "SD0_DATA5", "SD0_DATA6", "SD0_DATA7";
+			power-source = <1800>;
+		};
+
+		sd0_emmc_ctrl {
+			pins = "SD0_CLK", "SD0_CMD";
+			power-source = <1800>;
+		};
+
+		sd0_emmc_rst {
+			pins = "SD0_RST#";
+			power-source = <1800>;
+		};
+	};
+
+	sdhi0_pins: sd0 {
+		sd0_data {
+			pins = "SD0_DATA0", "SD0_DATA1", "SD0_DATA2", "SD0_DATA3";
+			power-source = <3300>;
+		};
+
+		sd0_ctrl {
+			pins = "SD0_CLK", "SD0_CMD";
+			power-source = <3300>;
+		};
+
+		sd0_mux {
+			pinmux = <RZG2L_PORT_PINMUX(18, 0, 1)>; /* SD0_CD */
+		};
+	};
+
+	sdhi0_pins_uhs: sd0_uhs {
+		sd0_data_uhs {
+			pins = "SD0_DATA0", "SD0_DATA1", "SD0_DATA2", "SD0_DATA3";
+			power-source = <1800>;
+		};
+
+		sd0_ctrl_uhs {
+			pins = "SD0_CLK", "SD0_CMD";
+			power-source = <1800>;
+		};
+
+		sd0_mux_uhs {
+			pinmux = <RZG2L_PORT_PINMUX(18, 0, 1)>; /* SD0_CD */
+		};
+	};
+};
+
+&sbc {
+	pinctrl-0 = <&qspi0_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	flash@0 {
+		compatible = "micron,mt25qu512a", "jedec,spi-nor";
+		reg = <0>;
+		m25p,fast-read;
+		spi-max-frequency = <50000000>;
+		spi-rx-bus-width = <4>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			boot@0 {
+				reg = <0x00000000 0x2000000>;
+				read-only;
+			};
+			user@2000000 {
+				reg = <0x2000000 0x2000000>;
+			};
+		};
+	};
+};
+
+#if (!SW_SD0_DEV_SEL)
+&sdhi0 {
+	pinctrl-0 = <&sdhi0_pins>;
+	pinctrl-1 = <&sdhi0_pins_uhs>;
+	pinctrl-names = "default", "state_uhs";
+
+	vmmc-supply = <&reg_3p3v>;
+	vqmmc-supply = <&vccq_sdhi0>;
+	bus-width = <4>;
+	sd-uhs-sdr50;
+	sd-uhs-sdr104;
+	status = "okay";
+};
+#endif
+
+#if SW_SD0_DEV_SEL
+&sdhi0 {
+	pinctrl-0 = <&sdhi0_emmc_pins>;
+	pinctrl-1 = <&sdhi0_emmc_pins>;
+	pinctrl-names = "default", "state_uhs";
+
+	vmmc-supply = <&reg_3p3v>;
+	vqmmc-supply = <&reg_1p8v>;
+	bus-width = <8>;
+	mmc-hs200-1_8v;
+	non-removable;
+	fixed-emmc-driver-type = <1>;
+	status = "okay";
+};
+#endif
+
+&wdt0 {
+	status = "okay";
+	timeout-sec = <60>;
+};
+
+&wdt1 {
+	status = "okay";
+	timeout-sec = <60>;
+};
+
+&wdt2 {
+	status = "okay";
+	timeout-sec = <60>;
+};
diff --git a/arch/arm64/boot/dts/renesas/rzg2lc-smarc.dtsi b/arch/arm64/boot/dts/renesas/rzg2lc-smarc.dtsi
new file mode 100644
index 000000000000..6be25a8a28db
--- /dev/null
+++ b/arch/arm64/boot/dts/renesas/rzg2lc-smarc.dtsi
@@ -0,0 +1,115 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+/*
+ * Device Tree Source for the RZ/G2LC SMARC EVK parts
+ *
+ * Copyright (C) 2022 Renesas Electronics Corp.
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/rzg2l-pinctrl.h>
+
+/*
+ * DIP-Switch SW1 setting on SoM
+ * 1 : High; 0: Low
+ * SW1-2 : SW_SD0_DEV_SEL	(1: eMMC; 0: uSD)
+ * SW1-3 : SW_SCIF_CAN		(1: CAN1; 0: SCIF1)
+ * SW1-4 : SW_RSPI_CAN		(1: CAN1; 0: RSPI1)
+ * SW1-5 : SW_I2S0_I2S1		(1: I2S2 (HDMI audio); 0: I2S0)
+ * Please change below macros according to SW1 setting
+ */
+
+#define SW_SD0_DEV_SEL	1
+
+#define SW_SCIF_CAN	0
+#if (SW_SCIF_CAN)
+/* Due to HW routing, SW_RSPI_CAN is always 0 when SW_SCIF_CAN is set to 1 */
+#define SW_RSPI_CAN	0
+#else
+/* Please set SW_RSPI_CAN. Default value is 1 */
+#define SW_RSPI_CAN	1
+#endif
+
+#if (SW_SCIF_CAN && SW_RSPI_CAN)
+#error "Can not set 1 to both SW_SCIF_CAN and SW_RSPI_CAN due to HW routing"
+#endif
+
+#include "rzg2lc-smarc-som.dtsi"
+#include "rzg2lc-smarc-pinfunction.dtsi"
+#include "rz-smarc-common.dtsi"
+
+/* comment the #define statement to disable SCIF1 (SER0) on PMOD1 (CN7) */
+#define PMOD1_SER0	1
+
+/ {
+	aliases {
+		serial1 = &scif1;
+		i2c2 = &i2c2;
+	};
+};
+
+#if (SW_SCIF_CAN || SW_RSPI_CAN)
+&canfd {
+	pinctrl-0 = <&can1_pins>;
+	/delete-node/ channel@0;
+};
+#else
+&canfd {
+	/delete-property/ pinctrl-0;
+	/delete-property/ pinctrl-names;
+	status = "disabled";
+};
+#endif
+
+&cpu_dai {
+	sound-dai = <&ssi0>;
+};
+
+&i2c2 {
+	pinctrl-0 = <&i2c2_pins>;
+	pinctrl-names = "default";
+	clock-frequency = <400000>;
+
+	status = "okay";
+
+	wm8978: codec@1a {
+		compatible = "wlf,wm8978";
+		#sound-dai-cells = <0>;
+		reg = <0x1a>;
+	};
+};
+
+/*
+ * To enable SCIF1 (SER0) on PMOD1 (CN7), On connector board
+ * SW1 should be at position 2->3 so that SER0_CTS# line is activated
+ * SW2 should be at position 2->3 so that SER0_TX line is activated
+ * SW3 should be at position 2->3 so that SER0_RX line is activated
+ * SW4 should be at position 2->3 so that SER0_RTS# line is activated
+ */
+#if (!SW_SCIF_CAN && PMOD1_SER0)
+&scif1 {
+	pinctrl-0 = <&scif1_pins>;
+	pinctrl-names = "default";
+
+	uart-has-rtscts;
+	status = "okay";
+};
+#endif
+
+&ssi0 {
+	pinctrl-0 = <&ssi0_pins>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+#if (SW_RSPI_CAN)
+&spi1 {
+	/delete-property/ pinctrl-0;
+	/delete-property/ pinctrl-names;
+	status = "disabled";
+};
+#endif
+
+&vccq_sdhi1 {
+	gpios = <&pinctrl RZG2L_GPIO(39, 1) GPIO_ACTIVE_HIGH>;
+};
diff --git a/arch/arm64/boot/dts/renesas/rzg2ul-smarc-pinfunction.dtsi b/arch/arm64/boot/dts/renesas/rzg2ul-smarc-pinfunction.dtsi
new file mode 100644
index 000000000000..bd8bc858c28c
--- /dev/null
+++ b/arch/arm64/boot/dts/renesas/rzg2ul-smarc-pinfunction.dtsi
@@ -0,0 +1,119 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+/*
+ * Device Tree Source for the RZ/G2UL SMARC pincontrol parts
+ *
+ * Copyright (C) 2022 Renesas Electronics Corp.
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/rzg2l-pinctrl.h>
+
+&pinctrl {
+	pinctrl-0 = <&sound_clk_pins>;
+	pinctrl-names = "default";
+
+	can0_pins: can0 {
+		pinmux = <RZG2L_PORT_PINMUX(1, 1, 3)>, /* TX */
+			 <RZG2L_PORT_PINMUX(1, 2, 3)>; /* RX */
+	};
+
+#if (SW_ET0_EN_N)
+	can0-stb-hog {
+		gpio-hog;
+		gpios = <RZG2L_GPIO(2, 2) GPIO_ACTIVE_HIGH>;
+		output-low;
+		line-name = "can0_stb";
+	};
+#endif
+
+	can1_pins: can1 {
+		pinmux = <RZG2L_PORT_PINMUX(2, 0, 3)>, /* TX */
+			 <RZG2L_PORT_PINMUX(2, 1, 3)>; /* RX */
+	};
+
+#if (SW_ET0_EN_N)
+	can1-stb-hog {
+		gpio-hog;
+		gpios = <RZG2L_GPIO(2, 3) GPIO_ACTIVE_HIGH>;
+		output-low;
+		line-name = "can1_stb";
+	};
+#endif
+
+	i2c0_pins: i2c0 {
+		pins = "RIIC0_SDA", "RIIC0_SCL";
+		input-enable;
+	};
+
+	i2c1_pins: i2c1 {
+		pins = "RIIC1_SDA", "RIIC1_SCL";
+		input-enable;
+	};
+
+	scif0_pins: scif0 {
+		pinmux = <RZG2L_PORT_PINMUX(6, 4, 6)>, /* TxD */
+			 <RZG2L_PORT_PINMUX(6, 3, 6)>; /* RxD */
+	};
+
+	sd1-pwr-en-hog {
+		gpio-hog;
+		gpios = <RZG2L_GPIO(0, 3) GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "sd1_pwr_en";
+	};
+
+	sdhi1_pins: sd1 {
+		sd1_data {
+			pins = "SD1_DATA0", "SD1_DATA1", "SD1_DATA2", "SD1_DATA3";
+			power-source = <3300>;
+		};
+
+		sd1_ctrl {
+			pins = "SD1_CLK", "SD1_CMD";
+			power-source = <3300>;
+		};
+
+		sd1_mux {
+			pinmux = <RZG2L_PORT_PINMUX(0, 2, 1)>; /* SD1_CD */
+		};
+	};
+
+	sdhi1_pins_uhs: sd1_uhs {
+		sd1_data_uhs {
+			pins = "SD1_DATA0", "SD1_DATA1", "SD1_DATA2", "SD1_DATA3";
+			power-source = <1800>;
+		};
+
+		sd1_ctrl_uhs {
+			pins = "SD1_CLK", "SD1_CMD";
+			power-source = <1800>;
+		};
+
+		sd1_mux_uhs {
+			pinmux = <RZG2L_PORT_PINMUX(0, 2, 1)>; /* SD1_CD */
+		};
+	};
+
+	sound_clk_pins: sound_clk {
+		pins = "AUDIO_CLK1", "AUDIO_CLK2";
+		input-enable;
+	};
+
+	ssi1_pins: ssi1 {
+		pinmux = <RZG2L_PORT_PINMUX(3, 0, 2)>, /* BCK */
+			 <RZG2L_PORT_PINMUX(3, 1, 2)>, /* RCK */
+			 <RZG2L_PORT_PINMUX(3, 2, 2)>, /* TXD */
+			 <RZG2L_PORT_PINMUX(3, 3, 2)>; /* RXD */
+	};
+
+	usb0_pins: usb0 {
+		pinmux = <RZG2L_PORT_PINMUX(5, 0, 1)>, /* VBUS */
+			 <RZG2L_PORT_PINMUX(5, 2, 1)>, /* OVC */
+			 <RZG2L_PORT_PINMUX(5, 3, 1)>; /* OTG_ID */
+	};
+
+	usb1_pins: usb1 {
+		pinmux = <RZG2L_PORT_PINMUX(5, 4, 5)>, /* OVC */
+			 <RZG2L_PORT_PINMUX(6, 0, 1)>; /* VBUS */
+	};
+};
diff --git a/arch/arm64/boot/dts/renesas/rzg2ul-smarc-som.dtsi b/arch/arm64/boot/dts/renesas/rzg2ul-smarc-som.dtsi
new file mode 100644
index 000000000000..2a0feb53f0dc
--- /dev/null
+++ b/arch/arm64/boot/dts/renesas/rzg2ul-smarc-som.dtsi
@@ -0,0 +1,265 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+/*
+ * Device Tree Source for the RZ/G2UL SMARC SOM common parts
+ *
+ * Copyright (C) 2022 Renesas Electronics Corp.
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/rzg2l-pinctrl.h>
+
+/ {
+	aliases {
+		ethernet0 = &eth0;
+		ethernet1 = &eth1;
+	};
+
+	chosen {
+		bootargs = "ignore_loglevel rw root=/dev/nfs ip=on";
+	};
+
+	memory@48000000 {
+		device_type = "memory";
+		/* first 128MB is reserved for secure area. */
+		reg = <0x0 0x48000000 0x0 0x38000000>;
+	};
+
+	reg_1p8v: regulator-1p8v {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-1.8V";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "fixed-3.3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+#if !(SW_SW0_DEV_SEL)
+	vccq_sdhi0: regulator-vccq-sdhi0 {
+		compatible = "regulator-gpio";
+
+		regulator-name = "SDHI0 VccQ";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+		states = <3300000 1>, <1800000 0>;
+		regulator-boot-on;
+		gpios = <&pinctrl RZG2L_GPIO(6, 2) GPIO_ACTIVE_HIGH>;
+		regulator-always-on;
+	};
+#endif
+};
+
+#if (SW_SW0_DEV_SEL)
+&adc {
+	pinctrl-0 = <&adc_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+#endif
+
+#if (!SW_ET0_EN_N)
+&eth0 {
+	pinctrl-0 = <&eth0_pins>;
+	pinctrl-names = "default";
+	phy-handle = <&phy0>;
+	phy-mode = "rgmii-id";
+	status = "okay";
+
+	phy0: ethernet-phy@7 {
+		compatible = "ethernet-phy-id0022.1640",
+			     "ethernet-phy-ieee802.3-c22";
+		reg = <7>;
+		rxc-skew-psec = <2400>;
+		txc-skew-psec = <2400>;
+		rxdv-skew-psec = <0>;
+		txdv-skew-psec = <0>;
+		rxd0-skew-psec = <0>;
+		rxd1-skew-psec = <0>;
+		rxd2-skew-psec = <0>;
+		rxd3-skew-psec = <0>;
+		txd0-skew-psec = <0>;
+		txd1-skew-psec = <0>;
+		txd2-skew-psec = <0>;
+		txd3-skew-psec = <0>;
+	};
+};
+#endif
+
+&eth1 {
+	pinctrl-0 = <&eth1_pins>;
+	pinctrl-names = "default";
+	phy-handle = <&phy1>;
+	phy-mode = "rgmii-id";
+	status = "okay";
+
+	phy1: ethernet-phy@7 {
+		compatible = "ethernet-phy-id0022.1640",
+			     "ethernet-phy-ieee802.3-c22";
+		reg = <7>;
+		rxc-skew-psec = <2400>;
+		txc-skew-psec = <2400>;
+		rxdv-skew-psec = <0>;
+		txdv-skew-psec = <0>;
+		rxd0-skew-psec = <0>;
+		rxd1-skew-psec = <0>;
+		rxd2-skew-psec = <0>;
+		rxd3-skew-psec = <0>;
+		txd0-skew-psec = <0>;
+		txd1-skew-psec = <0>;
+		txd2-skew-psec = <0>;
+		txd3-skew-psec = <0>;
+	};
+};
+
+&extal_clk {
+	clock-frequency = <24000000>;
+};
+
+&ostm1 {
+	status = "okay";
+};
+
+&ostm2 {
+	status = "okay";
+};
+
+&pinctrl {
+	adc_pins: adc {
+		pinmux = <RZG2L_PORT_PINMUX(6, 2, 1)>; /* ADC_TRG */
+	};
+
+	eth0_pins: eth0 {
+		pinmux = <RZG2L_PORT_PINMUX(4, 5, 1)>, /* ET0_LINKSTA */
+			 <RZG2L_PORT_PINMUX(4, 3, 1)>, /* ET0_MDC */
+			 <RZG2L_PORT_PINMUX(4, 4, 1)>, /* ET0_MDIO */
+			 <RZG2L_PORT_PINMUX(1, 0, 1)>, /* ET0_TXC */
+			 <RZG2L_PORT_PINMUX(1, 1, 1)>, /* ET0_TX_CTL */
+			 <RZG2L_PORT_PINMUX(1, 2, 1)>, /* ET0_TXD0 */
+			 <RZG2L_PORT_PINMUX(1, 3, 1)>, /* ET0_TXD1 */
+			 <RZG2L_PORT_PINMUX(1, 4, 1)>, /* ET0_TXD2 */
+			 <RZG2L_PORT_PINMUX(2, 0, 1)>, /* ET0_TXD3 */
+			 <RZG2L_PORT_PINMUX(3, 0, 1)>, /* ET0_RXC */
+			 <RZG2L_PORT_PINMUX(3, 1, 1)>, /* ET0_RX_CTL */
+			 <RZG2L_PORT_PINMUX(3, 2, 1)>, /* ET0_RXD0 */
+			 <RZG2L_PORT_PINMUX(3, 3, 1)>, /* ET0_RXD1 */
+			 <RZG2L_PORT_PINMUX(4, 0, 1)>, /* ET0_RXD2 */
+			 <RZG2L_PORT_PINMUX(4, 1, 1)>; /* ET0_RXD3 */
+	};
+
+	eth1_pins: eth1 {
+		pinmux = <RZG2L_PORT_PINMUX(10, 4, 1)>, /* ET1_LINKSTA */
+			 <RZG2L_PORT_PINMUX(10, 2, 1)>, /* ET1_MDC */
+			 <RZG2L_PORT_PINMUX(10, 3, 1)>, /* ET1_MDIO */
+			 <RZG2L_PORT_PINMUX(7, 0, 1)>, /* ET1_TXC */
+			 <RZG2L_PORT_PINMUX(7, 1, 1)>, /* ET1_TX_CTL */
+			 <RZG2L_PORT_PINMUX(7, 2, 1)>, /* ET1_TXD0 */
+			 <RZG2L_PORT_PINMUX(7, 3, 1)>, /* ET1_TXD1 */
+			 <RZG2L_PORT_PINMUX(7, 4, 1)>, /* ET1_TXD2 */
+			 <RZG2L_PORT_PINMUX(8, 0, 1)>, /* ET1_TXD3 */
+			 <RZG2L_PORT_PINMUX(8, 4, 1)>, /* ET1_RXC */
+			 <RZG2L_PORT_PINMUX(9, 0, 1)>, /* ET1_RX_CTL */
+			 <RZG2L_PORT_PINMUX(9, 1, 1)>, /* ET1_RXD0 */
+			 <RZG2L_PORT_PINMUX(9, 2, 1)>, /* ET1_RXD1 */
+			 <RZG2L_PORT_PINMUX(9, 3, 1)>, /* ET1_RXD2 */
+			 <RZG2L_PORT_PINMUX(10, 0, 1)>; /* ET1_RXD3 */
+	};
+
+	sdhi0_emmc_pins: sd0emmc {
+		sd0_emmc_data {
+			pins = "SD0_DATA0", "SD0_DATA1", "SD0_DATA2", "SD0_DATA3",
+			       "SD0_DATA4", "SD0_DATA5", "SD0_DATA6", "SD0_DATA7";
+			power-source = <1800>;
+		};
+
+		sd0_emmc_ctrl {
+			pins = "SD0_CLK", "SD0_CMD";
+			power-source = <1800>;
+		};
+
+		sd0_emmc_rst {
+			pins = "SD0_RST#";
+			power-source = <1800>;
+		};
+	};
+
+	sdhi0_pins: sd0 {
+		sd0_data {
+			pins = "SD0_DATA0", "SD0_DATA1", "SD0_DATA2", "SD0_DATA3";
+			power-source = <3300>;
+		};
+
+		sd0_ctrl {
+			pins = "SD0_CLK", "SD0_CMD";
+			power-source = <3300>;
+		};
+
+		sd0_mux {
+			pinmux = <RZG2L_PORT_PINMUX(0, 0, 1)>; /* SD0_CD */
+		};
+	};
+
+	sdhi0_pins_uhs: sd0_uhs {
+		sd0_data_uhs {
+			pins = "SD0_DATA0", "SD0_DATA1", "SD0_DATA2", "SD0_DATA3";
+			power-source = <1800>;
+		};
+
+		sd0_ctrl_uhs {
+			pins = "SD0_CLK", "SD0_CMD";
+			power-source = <1800>;
+		};
+
+		sd0_mux_uhs {
+			pinmux = <RZG2L_PORT_PINMUX(0, 0, 1)>; /* SD0_CD */
+		};
+	};
+
+	spi1_pins: rspi1 {
+		pinmux = <RZG2L_PORT_PINMUX(4, 0, 2)>, /* CK */
+			 <RZG2L_PORT_PINMUX(4, 1, 2)>, /* MOSI */
+			 <RZG2L_PORT_PINMUX(4, 2, 2)>, /* MISO */
+			 <RZG2L_PORT_PINMUX(4, 3, 2)>; /* SSL */
+	};
+};
+
+#if (SW_SW0_DEV_SEL)
+&sdhi0 {
+	pinctrl-0 = <&sdhi0_emmc_pins>;
+	pinctrl-1 = <&sdhi0_emmc_pins>;
+	pinctrl-names = "default", "state_uhs";
+
+	vmmc-supply = <&reg_3p3v>;
+	vqmmc-supply = <&reg_1p8v>;
+	bus-width = <8>;
+	mmc-hs200-1_8v;
+	non-removable;
+	fixed-emmc-driver-type = <1>;
+	status = "okay";
+};
+#else
+&sdhi0 {
+	pinctrl-0 = <&sdhi0_pins>;
+	pinctrl-1 = <&sdhi0_pins_uhs>;
+	pinctrl-names = "default", "state_uhs";
+
+	vmmc-supply = <&reg_3p3v>;
+	vqmmc-supply = <&vccq_sdhi0>;
+	bus-width = <4>;
+	sd-uhs-sdr50;
+	sd-uhs-sdr104;
+	status = "okay";
+};
+#endif
+
+&wdt0 {
+	status = "okay";
+	timeout-sec = <60>;
+};
diff --git a/arch/arm64/boot/dts/renesas/rzg2ul-smarc.dtsi b/arch/arm64/boot/dts/renesas/rzg2ul-smarc.dtsi
new file mode 100644
index 000000000000..2a1331ed1a5c
--- /dev/null
+++ b/arch/arm64/boot/dts/renesas/rzg2ul-smarc.dtsi
@@ -0,0 +1,58 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+/*
+ * Device Tree Source for the RZ/G2UL Type-1 SMARC EVK parts
+ *
+ * Copyright (C) 2022 Renesas Electronics Corp.
+ */
+
+#include "rzg2ul-smarc-pinfunction.dtsi"
+#include "rz-smarc-common.dtsi"
+
+#if (!SW_ET0_EN_N)
+&canfd {
+	/delete-property/ pinctrl-0;
+	/delete-property/ pinctrl-names;
+	status = "disabled";
+};
+#endif
+
+&cpu_dai {
+	sound-dai = <&ssi1>;
+};
+
+&i2c1 {
+	wm8978: codec@1a {
+		compatible = "wlf,wm8978";
+		#sound-dai-cells = <0>;
+		reg = <0x1a>;
+	};
+};
+
+#if (SW_ET0_EN_N)
+&ssi1 {
+	pinctrl-0 = <&ssi1_pins>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+#else
+&snd_rzg2l {
+	status = "disabled";
+};
+
+&spi1 {
+	/delete-property/ pinctrl-0;
+	/delete-property/ pinctrl-names;
+	status = "disabled";
+};
+
+&ssi1 {
+	/delete-property/ pinctrl-0;
+	/delete-property/ pinctrl-names;
+	status = "disabled";
+};
+#endif
+
+&vccq_sdhi1 {
+	gpios = <&pinctrl RZG2L_GPIO(6, 1) GPIO_ACTIVE_HIGH>;
+};
diff --git a/arch/arm64/boot/dts/renesas/salvator-common.dtsi b/arch/arm64/boot/dts/renesas/salvator-common.dtsi
index bf37777dca31..d97473401819 100644
--- a/arch/arm64/boot/dts/renesas/salvator-common.dtsi
+++ b/arch/arm64/boot/dts/renesas/salvator-common.dtsi
@@ -33,6 +33,14 @@
 
 / {
 	aliases {
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+		i2c2 = &i2c2;
+		i2c3 = &i2c3;
+		i2c4 = &i2c4;
+		i2c5 = &i2c5;
+		i2c6 = &i2c6;
+		i2c7 = &i2c_dvfs;
 		serial0 = &scif2;
 		serial1 = &hscif1;
 		ethernet0 = &avb;
@@ -97,6 +105,7 @@
 
 		port {
 			hdmi0_con: endpoint {
+				remote-endpoint = <&rcar_dw_hdmi0_out>;
 			};
 		};
 	};
@@ -169,7 +178,7 @@
 		};
 	};
 
-	reg_1p8v: regulator0 {
+	reg_1p8v: regulator-1p8v {
 		compatible = "regulator-fixed";
 		regulator-name = "fixed-1.8V";
 		regulator-min-microvolt = <1800000>;
@@ -178,7 +187,7 @@
 		regulator-always-on;
 	};
 
-	reg_3p3v: regulator1 {
+	reg_3p3v: regulator-3p3v {
 		compatible = "regulator-fixed";
 		regulator-name = "fixed-3.3V";
 		regulator-min-microvolt = <3300000>;
@@ -187,7 +196,7 @@
 		regulator-always-on;
 	};
 
-	reg_12v: regulator2 {
+	reg_12v: regulator-12v {
 		compatible = "regulator-fixed";
 		regulator-name = "fixed-12V";
 		regulator-min-microvolt = <12000000>;
@@ -385,7 +394,7 @@
 
 	ports {
 		port@0 {
-			endpoint {
+			du_out_rgb: endpoint {
 				remote-endpoint = <&adv7123_in>;
 			};
 		};
@@ -424,10 +433,6 @@
 	};
 };
 
-&hdmi0_con {
-	remote-endpoint = <&rcar_dw_hdmi0_out>;
-};
-
 #ifdef SOC_HAS_HDMI1
 &hdmi1 {
 	status = "okay";
@@ -835,7 +840,7 @@
 				frame-master = <&rsnd_endpoint0>;
 
 				playback = <&ssi0>, <&src0>, <&dvc0>;
-				capture  = <&ssi1>, <&src1>, <&dvc1>;
+				capture = <&ssi1>, <&src1>, <&dvc1>;
 			};
 		};
 
@@ -869,6 +874,55 @@
 	};
 };
 
+&rpc {
+	/* Left disabled.  To be enabled by firmware when unlocked. */
+
+	flash@0 {
+		compatible = "cypress,hyperflash", "cfi-flash";
+		reg = <0>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			bootparam@0 {
+				reg = <0x00000000 0x040000>;
+				read-only;
+			};
+			bl2@40000 {
+				reg = <0x00040000 0x140000>;
+				read-only;
+			};
+			cert_header_sa6@180000 {
+				reg = <0x00180000 0x040000>;
+				read-only;
+			};
+			bl31@1c0000 {
+				reg = <0x001c0000 0x040000>;
+				read-only;
+			};
+			tee@200000 {
+				reg = <0x00200000 0x440000>;
+				read-only;
+			};
+			uboot@640000 {
+				reg = <0x00640000 0x100000>;
+				read-only;
+			};
+			dtb@740000 {
+				reg = <0x00740000 0x080000>;
+			};
+			kernel@7c0000 {
+				reg = <0x007c0000 0x1400000>;
+			};
+			user@1bc0000 {
+				reg = <0x01bc0000 0x2440000>;
+			};
+		};
+	};
+};
+
 &rwdt {
 	timeout-sec = <60>;
 	status = "okay";
diff --git a/arch/arm64/boot/dts/renesas/salvator-panel-aa104xd12.dts b/arch/arm64/boot/dts/renesas/salvator-panel-aa104xd12.dts
new file mode 100644
index 000000000000..c83a30adc6ad
--- /dev/null
+++ b/arch/arm64/boot/dts/renesas/salvator-panel-aa104xd12.dts
@@ -0,0 +1,36 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device Tree overlay for the AA104XD12 panel connected to LVDS0 on a
+ * Salvator-X or Salvator-XS board
+ *
+ * Copyright 2021 Ideas on Board Oy
+ */
+
+/dts-v1/;
+/plugin/;
+
+&{/} {
+#include "panel-aa104xd12.dtsi"
+};
+
+&{/panel} {
+	backlight = <&backlight>;
+
+	port {
+		panel_in: endpoint {
+			remote-endpoint = <&lvds0_out>;
+		};
+	};
+};
+
+&lvds0 {
+	status = "okay";
+
+	ports {
+		port@1 {
+			lvds0_out: endpoint {
+				remote-endpoint = <&panel_in>;
+			};
+		};
+	};
+};
diff --git a/arch/arm64/boot/dts/renesas/ulcb-kf.dtsi b/arch/arm64/boot/dts/renesas/ulcb-kf.dtsi
index 61bd4df09df0..408871c2859d 100644
--- a/arch/arm64/boot/dts/renesas/ulcb-kf.dtsi
+++ b/arch/arm64/boot/dts/renesas/ulcb-kf.dtsi
@@ -26,6 +26,38 @@
 		select-gpios = <&gpio_exp_75 13 GPIO_ACTIVE_HIGH>;
 	};
 
+	hdmi1-out {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi1_con: endpoint {
+				remote-endpoint = <&adv7513_out>;
+			};
+		};
+	};
+
+	accel_3v3: regulator-acc-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "accel-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	hdmi_1v8: regulator-hdmi-1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "hdmi-1v8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	hdmi_3v3: regulator-hdmi-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "hdmi-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
 	snd_3p3v: regulator-snd_3p3v {
 		compatible = "regulator-fixed";
 		regulator-name = "snd-3.3v";
@@ -65,6 +97,16 @@
 	status = "okay";
 };
 
+&du {
+	ports {
+		port@0 {
+			du_out_rgb: endpoint {
+				remote-endpoint = <&adv7513_in>;
+			};
+		};
+	};
+};
+
 &ehci0 {
 	dr_mode = "otg";
 	status = "okay";
@@ -91,12 +133,72 @@
 		reg = <0x71>;
 		reset-gpios = <&gpio5 3 GPIO_ACTIVE_LOW>;
 
+		/* HDMIoSDA, HDMIoSCL */
+		i2c@4 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4>;
+
+			hdmi@3d {
+				compatible = "adi,adv7513";
+				reg = <0x3d>;
+
+				pinctrl-0 = <&hdmi1_pins>;
+				pinctrl-names = "default";
+
+				interrupt-parent = <&gpio2>;
+				interrupts = <14 IRQ_TYPE_LEVEL_LOW>;
+
+				clocks = <&cs2000>;
+				clock-names = "cec";
+
+				pd-gpios = <&gpio_exp_75 5 GPIO_ACTIVE_LOW>;
+
+				avdd-supply = <&hdmi_1v8>;
+				dvdd-supply = <&hdmi_1v8>;
+				pvdd-supply = <&hdmi_1v8>;
+				dvdd-3v-supply = <&hdmi_3v3>;
+				bgvdd-supply = <&hdmi_1v8>;
+
+				adi,input-depth = <8>;
+				adi,input-colorspace = "rgb";
+				adi,input-clock = "1x";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+						adv7513_in: endpoint {
+							remote-endpoint = <&du_out_rgb>;
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+						adv7513_out: endpoint {
+							remote-endpoint = <&hdmi1_con>;
+						};
+					};
+				};
+			};
+		};
+
 		/* Audio_SDA, Audio_SCL */
 		i2c@7 {
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <7>;
 
+			accelerometer@1d {
+				compatible = "st,lsm9ds0-imu";
+				reg = <0x1d>;
+
+				vdd-supply = <&accel_3v3>;
+				vddio-supply = <&accel_3v3>;
+			};
+
 			pcm3168a: audio-codec@44 {
 				#sound-dai-cells = <0>;
 				compatible = "ti,pcm3168a";
@@ -104,12 +206,12 @@
 				clocks = <&clksndsel>;
 				clock-names = "scki";
 
-				VDD1-supply	= <&snd_3p3v>;
-				VDD2-supply	= <&snd_3p3v>;
-				VCCAD1-supply	= <&snd_vcc5v>;
-				VCCAD2-supply	= <&snd_vcc5v>;
-				VCCDA1-supply	= <&snd_vcc5v>;
-				VCCDA2-supply	= <&snd_vcc5v>;
+				VDD1-supply = <&snd_3p3v>;
+				VDD2-supply = <&snd_3p3v>;
+				VCCAD1-supply = <&snd_vcc5v>;
+				VCCAD2-supply = <&snd_vcc5v>;
+				VCCDA1-supply = <&snd_vcc5v>;
+				VCCDA2-supply = <&snd_vcc5v>;
 
 				ports {
 					#address-cells = <1>;
@@ -131,6 +233,14 @@
 					};
 				};
 			};
+
+			gyroscope@6b {
+				compatible = "st,lsm9ds0-gyro";
+				reg = <0x6b>;
+
+				vdd-supply = <&accel_3v3>;
+				vddio-supply = <&accel_3v3>;
+			};
 		};
 	};
 
@@ -264,6 +374,19 @@
 		function = "can1";
 	};
 
+	hdmi1_pins: hdmi1 {
+		adv7513-interrupt {
+			pins = "GP_2_14";
+			bias-pull-up;
+		};
+
+		du {
+			groups = "du_rgb888", "du_sync", "du_clk_out_0",
+				 "du_disp";
+			function = "du";
+		};
+	};
+
 	hscif0_pins: hscif0 {
 		groups = "hscif0_data", "hscif0_ctrl";
 		function = "hscif0";
@@ -297,17 +420,14 @@
 		     &sound_pcm_pins>;
 
 	ports {
-		/* rsnd_port0/1 are on salvator-common */
+		/* rsnd_port0/1 are defined in ulcb.dtsi */
 		rsnd_port2: port@2 {
 			reg = <2>;
 			rsnd_for_pcm3168a_play: endpoint {
 				remote-endpoint = <&pcm3168a_endpoint_p>;
-
-				dai-format = "i2s";
-				bitclock-master = <&rsnd_for_pcm3168a_play>;
-				frame-master = <&rsnd_for_pcm3168a_play>;
+				bitclock-master;
+				frame-master;
 				dai-tdm-slot-num = <8>;
-
 				playback = <&ssi3>;
 			};
 		};
@@ -315,13 +435,10 @@
 			reg = <3>;
 			rsnd_for_pcm3168a_capture: endpoint {
 				remote-endpoint = <&pcm3168a_endpoint_c>;
-
-				dai-format = "i2s";
-				bitclock-master = <&rsnd_for_pcm3168a_capture>;
-				frame-master = <&rsnd_for_pcm3168a_capture>;
+				bitclock-master;
+				frame-master;
 				dai-tdm-slot-num = <6>;
-
-				capture  = <&ssi4>;
+				capture = <&ssi4>;
 			};
 		};
 	};
@@ -360,10 +477,10 @@
 };
 
 &sound_card {
-	dais = <&rsnd_port0	/* ak4613 */
-		&rsnd_port1	/* HDMI0  */
-		&rsnd_port2	/* pcm3168a playback */
-		&rsnd_port3	/* pcm3168a capture  */
+	links = <&rsnd_port0	/* ak4613 */
+		 &rsnd_port1	/* HDMI0  */
+		 &rsnd_port2	/* pcm3168a playback */
+		 &rsnd_port3	/* pcm3168a capture  */
 		>;
 };
 
diff --git a/arch/arm64/boot/dts/renesas/ulcb.dtsi b/arch/arm64/boot/dts/renesas/ulcb.dtsi
index 7edffe7f8cfa..29cedf4dc1a9 100644
--- a/arch/arm64/boot/dts/renesas/ulcb.dtsi
+++ b/arch/arm64/boot/dts/renesas/ulcb.dtsi
@@ -21,6 +21,14 @@
 	model = "Renesas R-Car Gen3 ULCB board";
 
 	aliases {
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+		i2c2 = &i2c2;
+		i2c3 = &i2c3;
+		i2c4 = &i2c4;
+		i2c5 = &i2c5;
+		i2c6 = &i2c6;
+		i2c7 = &i2c_dvfs;
 		serial0 = &scif2;
 		ethernet0 = &avb;
 		mmc0 = &sdhi2;
@@ -48,6 +56,7 @@
 
 		port {
 			hdmi0_con: endpoint {
+				remote-endpoint = <&rcar_dw_hdmi0_out>;
 			};
 		};
 	};
@@ -75,7 +84,7 @@
 		};
 	};
 
-	reg_1p8v: regulator0 {
+	reg_1p8v: regulator-1p8v {
 		compatible = "regulator-fixed";
 		regulator-name = "fixed-1.8V";
 		regulator-min-microvolt = <1800000>;
@@ -84,7 +93,7 @@
 		regulator-always-on;
 	};
 
-	reg_3p3v: regulator1 {
+	reg_3p3v: regulator-3p3v {
 		compatible = "regulator-fixed";
 		regulator-name = "fixed-3.3V";
 		regulator-min-microvolt = <3300000>;
@@ -94,11 +103,11 @@
 	};
 
 	sound_card: sound {
-		compatible = "audio-graph-card";
+		compatible = "audio-graph-card2";
 		label = "rcar-sound";
 
-		dais = <&rsnd_port0	/* ak4613 */
-			&rsnd_port1	/* HDMI0  */
+		links = <&rsnd_port0	/* ak4613 */
+			 &rsnd_port1	/* HDMI0  */
 			>;
 	};
 
@@ -199,10 +208,6 @@
 	};
 };
 
-&hdmi0_con {
-	remote-endpoint = <&rcar_dw_hdmi0_out>;
-};
-
 &i2c2 {
 	pinctrl-0 = <&i2c2_pins>;
 	pinctrl-names = "default";
@@ -411,25 +416,68 @@
 			reg = <0>;
 			rsnd_for_ak4613: endpoint {
 				remote-endpoint = <&ak4613_endpoint>;
-
-				dai-format = "left_j";
-				bitclock-master = <&rsnd_for_ak4613>;
-				frame-master = <&rsnd_for_ak4613>;
-
+				bitclock-master;
+				frame-master;
 				playback = <&ssi0>, <&src0>, <&dvc0>;
-				capture  = <&ssi1>, <&src1>, <&dvc1>;
+				capture = <&ssi1>, <&src1>, <&dvc1>;
 			};
 		};
 		rsnd_port1: port@1 {
 			reg = <1>;
 			rsnd_for_hdmi: endpoint {
 				remote-endpoint = <&dw_hdmi0_snd_in>;
+				bitclock-master;
+				frame-master;
+				playback = <&ssi2>;
+			};
+		};
+	};
+};
 
-				dai-format = "i2s";
-				bitclock-master = <&rsnd_for_hdmi>;
-				frame-master = <&rsnd_for_hdmi>;
+&rpc {
+	/* Left disabled.  To be enabled by firmware when unlocked. */
 
-				playback = <&ssi2>;
+	flash@0 {
+		compatible = "cypress,hyperflash", "cfi-flash";
+		reg = <0>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			bootparam@0 {
+				reg = <0x00000000 0x040000>;
+				read-only;
+			};
+			bl2@40000 {
+				reg = <0x00040000 0x140000>;
+				read-only;
+			};
+			cert_header_sa6@180000 {
+				reg = <0x00180000 0x040000>;
+				read-only;
+			};
+			bl31@1c0000 {
+				reg = <0x001c0000 0x040000>;
+				read-only;
+			};
+			tee@200000 {
+				reg = <0x00200000 0x440000>;
+				read-only;
+			};
+			uboot@640000 {
+				reg = <0x00640000 0x100000>;
+				read-only;
+			};
+			dtb@740000 {
+				reg = <0x00740000 0x080000>;
+			};
+			kernel@7c0000 {
+				reg = <0x007c0000 0x1400000>;
+			};
+			user@1bc0000 {
+				reg = <0x01bc0000 0x2440000>;
 			};
 		};
 	};
diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
index 479906f3ad7b..8c15593c0ca4 100644
--- a/arch/arm64/boot/dts/rockchip/Makefile
+++ b/arch/arm64/boot/dts/rockchip/Makefile
@@ -5,6 +5,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += px30-engicam-px30-core-ctouch2-of10.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += px30-engicam-px30-core-edimm2.2.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3308-evb.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3308-roc-cc.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3308-rock-pi-s.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3318-a95x-z2.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3326-odroid-go2.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-a1.dtb
@@ -20,6 +21,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-lion-haikou.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-orion-r68-meta.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-px5-evb.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-r88.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-eaidk-610.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-evb.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-ficus.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-firefly.dtb
@@ -39,12 +41,15 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-nanopi-m4.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-nanopi-m4b.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-nanopi-neo4.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-nanopi-r4s.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-nanopi-r4s-enterprise.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-orangepi.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-pinebook-pro.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-pinephone-pro.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-puma-haikou.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-roc-pc.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-roc-pc-mezzanine.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-roc-pc-plus.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-rock-4c-plus.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-rock-pi-4a.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-rock-pi-4a-plus.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-rock-pi-4b.dtb
@@ -56,5 +61,14 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-rockpro64.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-sapphire.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-sapphire-excavator.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399pro-rock-pi-n10.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-anbernic-rg353p.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-anbernic-rg503.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-pinenote-v1.1.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-pinenote-v1.2.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-quartz64-a.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-quartz64-b.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-roc-pc.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-soquartz-cm4.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-bpi-r2-pro.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-evb1-v10.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-rock-3a.dtb
diff --git a/arch/arm64/boot/dts/rockchip/px30-engicam-px30-core.dtsi b/arch/arm64/boot/dts/rockchip/px30-engicam-px30-core.dtsi
index 7249871530ab..5eecbefa8a33 100644
--- a/arch/arm64/boot/dts/rockchip/px30-engicam-px30-core.dtsi
+++ b/arch/arm64/boot/dts/rockchip/px30-engicam-px30-core.dtsi
@@ -2,8 +2,8 @@
 /*
  * Copyright (c) 2020 Fuzhou Rockchip Electronics Co., Ltd
  * Copyright (c) 2020 Engicam srl
- * Copyright (c) 2020 Amarula Solutons
- * Copyright (c) 2020 Amarula Solutons(India)
+ * Copyright (c) 2020 Amarula Solutions
+ * Copyright (c) 2020 Amarula Solutions(India)
  */
 
 #include <dt-bindings/gpio/gpio.h>
diff --git a/arch/arm64/boot/dts/rockchip/px30-evb.dts b/arch/arm64/boot/dts/rockchip/px30-evb.dts
index 848bc39cf86a..07008d84434c 100644
--- a/arch/arm64/boot/dts/rockchip/px30-evb.dts
+++ b/arch/arm64/boot/dts/rockchip/px30-evb.dts
@@ -450,8 +450,8 @@
 		dvdd-supply = <&vcc1v5_dvp>;
 		dovdd-supply = <&vcc1v8_dvp>;
 		pinctrl-names = "default";
-		pinctrl-0 = <&cif_clkout_m0>;
-		reset-gpios = <&gpio2 14 GPIO_ACTIVE_LOW>;
+		pinctrl-0 = <&cif_clkout_m0 &mipi_pdn>;
+		reset-gpios = <&gpio2 RK_PB6 GPIO_ACTIVE_LOW>;
 
 		port {
 			ucam_out: endpoint {
@@ -537,6 +537,19 @@
 				<0 RK_PA2 RK_FUNC_GPIO &pcfg_pull_none>;
 		};
 	};
+
+	cif-m0 {
+		cif_clkout_m0: cif-clkout-m0 {
+			rockchip,pins =
+				<2 RK_PB3 1 &pcfg_pull_none_12ma>;
+		};
+	};
+
+	mipi {
+		mipi_pdn: mipi-pdn {
+			rockchip,pins = <2 RK_PB6 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
 };
 
 &pmu_io_domains {
diff --git a/arch/arm64/boot/dts/rockchip/px30.dtsi b/arch/arm64/boot/dts/rockchip/px30.dtsi
index 00f50b05d55a..bfa3580429d1 100644
--- a/arch/arm64/boot/dts/rockchip/px30.dtsi
+++ b/arch/arm64/boot/dts/rockchip/px30.dtsi
@@ -365,6 +365,28 @@
 		status = "disabled";
 	};
 
+	i2s0_8ch: i2s@ff060000 {
+		compatible = "rockchip,px30-i2s-tdm";
+		reg = <0x0 0xff060000 0x0 0x1000>;
+		interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru SCLK_I2S0_TX>, <&cru SCLK_I2S0_RX>, <&cru HCLK_I2S0>;
+		clock-names = "mclk_tx", "mclk_rx", "hclk";
+		dmas = <&dmac 16>, <&dmac 17>;
+		dma-names = "tx", "rx";
+		rockchip,grf = <&grf>;
+		resets = <&cru SRST_I2S0_TX>, <&cru SRST_I2S0_RX>;
+		reset-names = "tx-m", "rx-m";
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2s0_8ch_sclktx &i2s0_8ch_sclkrx
+			     &i2s0_8ch_lrcktx &i2s0_8ch_lrckrx
+			     &i2s0_8ch_sdo0 &i2s0_8ch_sdi0
+			     &i2s0_8ch_sdo1 &i2s0_8ch_sdi1
+			     &i2s0_8ch_sdo2 &i2s0_8ch_sdi2
+			     &i2s0_8ch_sdo3 &i2s0_8ch_sdi3>;
+		#sound-dai-cells = <0>;
+		status = "disabled";
+	};
+
 	i2s1_2ch: i2s@ff070000 {
 		compatible = "rockchip,px30-i2s", "rockchip,rk3066-i2s";
 		reg = <0x0 0xff070000 0x0 0x1000>;
@@ -528,7 +550,7 @@
 	i2c0: i2c@ff180000 {
 		compatible = "rockchip,px30-i2c", "rockchip,rk3399-i2c";
 		reg = <0x0 0xff180000 0x0 0x1000>;
-		clocks =  <&cru SCLK_I2C0>, <&cru PCLK_I2C0>;
+		clocks = <&cru SCLK_I2C0>, <&cru PCLK_I2C0>;
 		clock-names = "i2c", "pclk";
 		interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
 		pinctrl-names = "default";
@@ -711,7 +733,7 @@
 		clock-names = "pclk", "timer";
 	};
 
-	dmac: dmac@ff240000 {
+	dmac: dma-controller@ff240000 {
 		compatible = "arm,pl330", "arm,primecell";
 		reg = <0x0 0xff240000 0x0 0x4000>;
 		interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>,
@@ -1072,7 +1094,7 @@
 	};
 
 	dsi: dsi@ff450000 {
-		compatible = "rockchip,px30-mipi-dsi";
+		compatible = "rockchip,px30-mipi-dsi", "snps,dw-mipi-dsi";
 		reg = <0x0 0xff450000 0x0 0x10000>;
 		interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&cru PCLK_MIPI_DSI>;
diff --git a/arch/arm64/boot/dts/rockchip/rk3308-evb.dts b/arch/arm64/boot/dts/rockchip/rk3308-evb.dts
index 9b4f855ea5d4..9fe9b0d11003 100644
--- a/arch/arm64/boot/dts/rockchip/rk3308-evb.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3308-evb.dts
@@ -75,7 +75,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pwr_key>;
 
-		power {
+		key-power {
 			gpios = <&gpio0 RK_PA6 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
 			label = "GPIO Key Power";
diff --git a/arch/arm64/boot/dts/rockchip/rk3308-roc-cc.dts b/arch/arm64/boot/dts/rockchip/rk3308-roc-cc.dts
index 665b2e69455d..ea6820902ede 100644
--- a/arch/arm64/boot/dts/rockchip/rk3308-roc-cc.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3308-roc-cc.dts
@@ -97,7 +97,7 @@
 		regulator-max-microvolt = <3300000>;
 		regulator-always-on;
 		regulator-boot-on;
-		vim-supply = <&vcc_io>;
+		vin-supply = <&vcc_io>;
 	};
 
 	vdd_core: vdd-core {
diff --git a/arch/arm64/boot/dts/rockchip/rk3308-rock-pi-s.dts b/arch/arm64/boot/dts/rockchip/rk3308-rock-pi-s.dts
new file mode 100644
index 000000000000..a71f249ed384
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3308-rock-pi-s.dts
@@ -0,0 +1,253 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2019 Akash Gajjar <akash@openedev.com>
+ * Copyright (c) 2019 Jagan Teki <jagan@openedev.com>
+ */
+
+/dts-v1/;
+#include "rk3308.dtsi"
+
+/ {
+	model = "Radxa ROCK Pi S";
+	compatible = "radxa,rockpis", "rockchip,rk3308";
+
+	aliases {
+		ethernet0 = &gmac;
+		mmc0 = &emmc;
+		mmc1 = &sdmmc;
+	};
+
+	chosen {
+		stdout-path = "serial0:1500000n8";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&green_led_gio>, <&heartbeat_led_gpio>;
+
+		green-led {
+			default-state = "on";
+			gpios = <&gpio0 RK_PA6 GPIO_ACTIVE_HIGH>;
+			label = "rockpis:green:power";
+			linux,default-trigger = "default-on";
+		};
+
+		blue-led {
+			default-state = "on";
+			gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_HIGH>;
+			label = "rockpis:blue:user";
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	sdio_pwrseq: sdio-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		pinctrl-0 = <&wifi_enable_h>;
+		pinctrl-names = "default";
+		reset-gpios = <&gpio0 RK_PA2 GPIO_ACTIVE_LOW>;
+	};
+
+	vcc_1v8: vcc-1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_1v8";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vcc_io>;
+	};
+
+	vcc_io: vcc-io {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_io";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc5v0_sys>;
+	};
+
+	vcc_ddr: vcc-ddr {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_ddr";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <1500000>;
+		regulator-max-microvolt = <1500000>;
+		vin-supply = <&vcc5v0_sys>;
+	};
+
+	vcc5v0_otg: vcc5v0-otg {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio0 RK_PC5 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&otg_vbus_drv>;
+		regulator-name = "vcc5v0_otg";
+		regulator-always-on;
+		vin-supply = <&vcc5v0_sys>;
+	};
+
+	vcc5v0_sys: vcc5v0-sys {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc5v0_sys";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	vdd_core: vdd-core {
+		compatible = "pwm-regulator";
+		pwms = <&pwm0 0 5000 1>;
+		pwm-supply = <&vcc5v0_sys>;
+		regulator-name = "vdd_core";
+		regulator-min-microvolt = <827000>;
+		regulator-max-microvolt = <1340000>;
+		regulator-init-microvolt = <1015000>;
+		regulator-settling-time-up-us = <250>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vdd_log: vdd-log {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_log";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <1050000>;
+		regulator-max-microvolt = <1050000>;
+		vin-supply = <&vcc5v0_sys>;
+	};
+};
+
+&cpu0 {
+	cpu-supply = <&vdd_core>;
+};
+
+&emmc {
+	bus-width = <4>;
+	cap-mmc-highspeed;
+	mmc-hs200-1_8v;
+	non-removable;
+	vmmc-supply = <&vcc_io>;
+	status = "okay";
+};
+
+&gmac {
+	clock_in_out = "output";
+	phy-supply = <&vcc_io>;
+	snps,reset-gpio = <&gpio0 RK_PA7 GPIO_ACTIVE_LOW>;
+	snps,reset-active-low;
+	snps,reset-delays-us = <0 50000 50000>;
+	status = "okay";
+};
+
+&i2c1 {
+	status = "okay";
+};
+
+&pinctrl {
+	pinctrl-names = "default";
+	pinctrl-0 = <&rtc_32k>;
+
+	leds {
+		green_led_gio: green-led-gpio {
+			rockchip,pins = <0 RK_PA6 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		heartbeat_led_gpio: heartbeat-led-gpio {
+			rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	usb {
+		otg_vbus_drv: otg-vbus-drv {
+			rockchip,pins = <0 RK_PC5 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	sdio-pwrseq {
+		wifi_enable_h: wifi-enable-h {
+			rockchip,pins = <0 RK_PA2 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		wifi_host_wake: wifi-host-wake {
+			rockchip,pins = <0 RK_PA0 RK_FUNC_GPIO &pcfg_pull_down>;
+		};
+	};
+};
+
+&pwm0 {
+	status = "okay";
+	pinctrl-0 = <&pwm0_pin_pull_down>;
+};
+
+&saradc {
+	vref-supply = <&vcc_1v8>;
+	status = "okay";
+};
+
+&sdio {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	cap-sd-highspeed;
+	cap-sdio-irq;
+	keep-power-in-suspend;
+	max-frequency = <1000000>;
+	mmc-pwrseq = <&sdio_pwrseq>;
+	non-removable;
+	sd-uhs-sdr104;
+	status = "okay";
+};
+
+&sdmmc {
+	cap-sd-highspeed;
+	status = "okay";
+};
+
+&u2phy {
+	status = "okay";
+
+	u2phy_host: host-port {
+		phy-supply = <&vcc5v0_otg>;
+		status = "okay";
+	};
+
+	u2phy_otg: otg-port {
+		phy-supply = <&vcc5v0_otg>;
+		status = "okay";
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart4 {
+	status = "okay";
+
+	bluetooth {
+		compatible = "realtek,rtl8723bs-bt";
+		device-wake-gpios = <&gpio4 RK_PB3 GPIO_ACTIVE_HIGH>;
+		host-wake-gpios = <&gpio4 RK_PB4 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&usb_host_ehci {
+	status = "okay";
+};
+
+&usb_host_ohci {
+	status = "okay";
+};
+
+&usb20_otg {
+	dr_mode = "peripheral";
+	status = "okay";
+};
+
+&wdt {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/rockchip/rk3308.dtsi b/arch/arm64/boot/dts/rockchip/rk3308.dtsi
index 1cbe2126186e..2dfa67f1cd67 100644
--- a/arch/arm64/boot/dts/rockchip/rk3308.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3308.dtsi
@@ -745,10 +745,11 @@
 	cru: clock-controller@ff500000 {
 		compatible = "rockchip,rk3308-cru";
 		reg = <0x0 0xff500000 0x0 0x1000>;
+		clocks = <&xin24m>;
+		clock-names = "xin24m";
+		rockchip,grf = <&grf>;
 		#clock-cells = <1>;
 		#reset-cells = <1>;
-		rockchip,grf = <&grf>;
-
 		assigned-clocks = <&cru SCLK_RTC32K>;
 		assigned-clock-rates = <32768>;
 	};
diff --git a/arch/arm64/boot/dts/rockchip/rk3326-odroid-go2.dts b/arch/arm64/boot/dts/rockchip/rk3326-odroid-go2.dts
index ea0695b51ecd..72899a714310 100644
--- a/arch/arm64/boot/dts/rockchip/rk3326-odroid-go2.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3326-odroid-go2.dts
@@ -52,6 +52,25 @@
 		pwms = <&pwm1 0 25000 0>;
 	};
 
+	battery: battery {
+		compatible = "simple-battery";
+		charge-full-design-microamp-hours = <3000000>;
+		charge-term-current-microamp = <300000>;
+		constant-charge-current-max-microamp = <2000000>;
+		constant-charge-voltage-max-microvolt = <4200000>;
+		factory-internal-resistance-micro-ohms = <180000>;
+		voltage-max-design-microvolt = <4100000>;
+		voltage-min-design-microvolt = <3500000>;
+
+		ocv-capacity-celsius = <20>;
+		ocv-capacity-table-0 =	<4046950 100>, <4001920 95>, <3967900 90>, <3919950 85>,
+					<3888450 80>, <3861850 75>, <3831540 70>, <3799130 65>,
+					<3768190 60>, <3745650 55>, <3726610 50>, <3711630 45>,
+					<3696720 40>, <3685660 35>, <3674950 30>, <3663050 25>,
+					<3649470 20>, <3635260 15>, <3616920 10>, <3592440 5>,
+					<3574170 0>;
+	};
+
 	gpio-keys {
 		compatible = "gpio-keys";
 		pinctrl-names = "default";
@@ -71,82 +90,82 @@
 		 * |------------------------------------------------|
 		 */
 
-		sw1 {
+		button-sw1 {
 			gpios = <&gpio1 RK_PB4 GPIO_ACTIVE_LOW>;
 			label = "DPAD-UP";
 			linux,code = <BTN_DPAD_UP>;
 		};
-		sw2 {
+		button-sw2 {
 			gpios = <&gpio1 RK_PB5 GPIO_ACTIVE_LOW>;
 			label = "DPAD-DOWN";
 			linux,code = <BTN_DPAD_DOWN>;
 		};
-		sw3 {
+		button-sw3 {
 			gpios = <&gpio1 RK_PB6 GPIO_ACTIVE_LOW>;
 			label = "DPAD-LEFT";
 			linux,code = <BTN_DPAD_LEFT>;
 		};
-		sw4 {
+		button-sw4 {
 			gpios = <&gpio1 RK_PB7 GPIO_ACTIVE_LOW>;
 			label = "DPAD-RIGHT";
 			linux,code = <BTN_DPAD_RIGHT>;
 		};
-		sw5 {
+		button-sw5 {
 			gpios = <&gpio1 RK_PA2 GPIO_ACTIVE_LOW>;
 			label = "BTN-A";
 			linux,code = <BTN_EAST>;
 		};
-		sw6 {
+		button-sw6 {
 			gpios = <&gpio1 RK_PA5 GPIO_ACTIVE_LOW>;
 			label = "BTN-B";
 			linux,code = <BTN_SOUTH>;
 		};
-		sw7 {
+		button-sw7 {
 			gpios = <&gpio1 RK_PA6 GPIO_ACTIVE_LOW>;
 			label = "BTN-Y";
 			linux,code = <BTN_WEST>;
 		};
-		sw8 {
+		button-sw8 {
 			gpios = <&gpio1 RK_PA7 GPIO_ACTIVE_LOW>;
 			label = "BTN-X";
 			linux,code = <BTN_NORTH>;
 		};
-		sw9 {
+		button-sw9 {
 			gpios = <&gpio2 RK_PA0 GPIO_ACTIVE_LOW>;
 			label = "F1";
 			linux,code = <BTN_TRIGGER_HAPPY1>;
 		};
-		sw10 {
+		button-sw10 {
 			gpios = <&gpio2 RK_PA1 GPIO_ACTIVE_LOW>;
 			label = "F2";
 			linux,code = <BTN_TRIGGER_HAPPY2>;
 		};
-		sw11 {
+		button-sw11 {
 			gpios = <&gpio2 RK_PA2 GPIO_ACTIVE_LOW>;
 			label = "F3";
 			linux,code = <BTN_TRIGGER_HAPPY3>;
 		};
-		sw12 {
+		button-sw12 {
 			gpios = <&gpio2 RK_PA3 GPIO_ACTIVE_LOW>;
 			label = "F4";
 			linux,code = <BTN_TRIGGER_HAPPY4>;
 		};
-		sw13 {
+		button-sw13 {
 			gpios = <&gpio2 RK_PA4 GPIO_ACTIVE_LOW>;
 			label = "F5";
 			linux,code = <BTN_TRIGGER_HAPPY5>;
 		};
-		sw14 {
+		button-sw14 {
 			gpios = <&gpio2 RK_PA5 GPIO_ACTIVE_LOW>;
 			label = "F6";
 			linux,code = <BTN_TRIGGER_HAPPY6>;
 		};
-		sw15 {
+		button-sw15 {
 			gpios = <&gpio2 RK_PA6 GPIO_ACTIVE_LOW>;
 			label = "TOP-LEFT";
 			linux,code = <BTN_TL>;
 		};
-		sw16 {
+		button-sw16 {
 			gpios = <&gpio2 RK_PA7 GPIO_ACTIVE_LOW>;
 			label = "TOP-RIGHT";
 			linux,code = <BTN_TR>;
@@ -472,6 +491,13 @@
 			};
 		};
 
+		rk817_charger: charger {
+			monitored-battery = <&battery>;
+			rockchip,resistor-sense-micro-ohms = <10000>;
+			rockchip,sleep-enter-current-microamp = <300000>;
+			rockchip,sleep-filter-current-microamp = <100000>;
+		};
+
 		rk817_codec: codec {
 			rockchip,mic-in-differential;
 		};
diff --git a/arch/arm64/boot/dts/rockchip/rk3328-a1.dts b/arch/arm64/boot/dts/rockchip/rk3328-a1.dts
index de2d3e88e27f..40bf808642b9 100644
--- a/arch/arm64/boot/dts/rockchip/rk3328-a1.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3328-a1.dts
@@ -160,6 +160,7 @@
 		pinctrl-0 = <&pmic_int_l>;
 		rockchip,system-power-controller;
 		wakeup-source;
+		#clock-cells = <0>;
 
 		vcc1-supply = <&vcc_sys>;
 		vcc2-supply = <&vcc_sys>;
diff --git a/arch/arm64/boot/dts/rockchip/rk3328-nanopi-r2s.dts b/arch/arm64/boot/dts/rockchip/rk3328-nanopi-r2s.dts
index 3857d487ab84..1445b879ac7a 100644
--- a/arch/arm64/boot/dts/rockchip/rk3328-nanopi-r2s.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3328-nanopi-r2s.dts
@@ -34,7 +34,7 @@
 		pinctrl-0 = <&reset_button_pin>;
 		pinctrl-names = "default";
 
-		reset {
+		key-reset {
 			label = "reset";
 			gpios = <&gpio0 RK_PA0 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_RESTART>;
diff --git a/arch/arm64/boot/dts/rockchip/rk3328.dtsi b/arch/arm64/boot/dts/rockchip/rk3328.dtsi
index 39db0b85b4da..49ae15708a0b 100644
--- a/arch/arm64/boot/dts/rockchip/rk3328.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3328.dtsi
@@ -306,6 +306,10 @@
 			};
 			power-domain@RK3328_PD_VIDEO {
 				reg = <RK3328_PD_VIDEO>;
+				clocks = <&cru ACLK_RKVDEC>,
+					 <&cru HCLK_RKVDEC>,
+					 <&cru SCLK_VDEC_CABAC>,
+					 <&cru SCLK_VDEC_CORE>;
 				#power-domain-cells = <0>;
 			};
 			power-domain@RK3328_PD_VPU {
@@ -489,7 +493,7 @@
 		status = "disabled";
 	};
 
-	dmac: dmac@ff1f0000 {
+	dmac: dma-controller@ff1f0000 {
 		compatible = "arm,pl330", "arm,primecell";
 		reg = <0x0 0xff1f0000 0x0 0x4000>;
 		interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
@@ -660,14 +664,28 @@
 		power-domains = <&power RK3328_PD_VPU>;
 	};
 
-	rkvdec_mmu: iommu@ff360480 {
+	vdec: video-codec@ff360000 {
+		compatible = "rockchip,rk3328-vdec", "rockchip,rk3399-vdec";
+		reg = <0x0 0xff360000 0x0 0x400>;
+		interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru ACLK_RKVDEC>, <&cru HCLK_RKVDEC>,
+			 <&cru SCLK_VDEC_CABAC>, <&cru SCLK_VDEC_CORE>;
+		clock-names = "axi", "ahb", "cabac", "core";
+		assigned-clocks = <&cru ACLK_RKVDEC>, <&cru SCLK_VDEC_CABAC>,
+				  <&cru SCLK_VDEC_CORE>;
+		assigned-clock-rates = <400000000>, <400000000>, <300000000>;
+		iommus = <&vdec_mmu>;
+		power-domains = <&power RK3328_PD_VIDEO>;
+	};
+
+	vdec_mmu: iommu@ff360480 {
 		compatible = "rockchip,iommu";
 		reg = <0x0 0xff360480 0x0 0x40>, <0x0 0xff3604c0 0x0 0x40>;
 		interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&cru ACLK_RKVDEC>, <&cru HCLK_RKVDEC>;
 		clock-names = "aclk", "iface";
 		#iommu-cells = <0>;
-		status = "disabled";
+		power-domains = <&power RK3328_PD_VIDEO>;
 	};
 
 	vop: vop@ff370000 {
diff --git a/arch/arm64/boot/dts/rockchip/rk3368-evb.dtsi b/arch/arm64/boot/dts/rockchip/rk3368-evb.dtsi
index 15d1fc541c38..083452c67711 100644
--- a/arch/arm64/boot/dts/rockchip/rk3368-evb.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3368-evb.dtsi
@@ -76,7 +76,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pwr_key>;
 
-		power {
+		key-power {
 			wakeup-source;
 			gpios = <&gpio0 RK_PA2 GPIO_ACTIVE_LOW>;
 			label = "GPIO Power";
diff --git a/arch/arm64/boot/dts/rockchip/rk3368-geekbox.dts b/arch/arm64/boot/dts/rockchip/rk3368-geekbox.dts
index 62aa97a0b8c9..be06e6e64d18 100644
--- a/arch/arm64/boot/dts/rockchip/rk3368-geekbox.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3368-geekbox.dts
@@ -43,7 +43,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pwr_key>;
 
-		power {
+		key-power {
 			gpios = <&gpio0 RK_PA2 GPIO_ACTIVE_LOW>;
 			label = "GPIO Power";
 			linux,code = <KEY_POWER>;
diff --git a/arch/arm64/boot/dts/rockchip/rk3368-orion-r68-meta.dts b/arch/arm64/boot/dts/rockchip/rk3368-orion-r68-meta.dts
index 3ebe15e03cf4..7f5bba0c6001 100644
--- a/arch/arm64/boot/dts/rockchip/rk3368-orion-r68-meta.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3368-orion-r68-meta.dts
@@ -44,7 +44,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pwr_key>;
 
-		power {
+		key-power {
 			wakeup-source;
 			gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_HIGH>;
 			label = "GPIO Power";
@@ -134,7 +134,7 @@
 
 	vccio_sd: vcc-io-sd-regulator {
 		compatible = "regulator-fixed";
-		regulator-name= "vccio_sd";
+		regulator-name = "vccio_sd";
 		regulator-min-microvolt = <1800000>;
 		regulator-max-microvolt = <3300000>;
 		regulator-always-on;
diff --git a/arch/arm64/boot/dts/rockchip/rk3368-px5-evb.dts b/arch/arm64/boot/dts/rockchip/rk3368-px5-evb.dts
index 5ccaa5f7a370..29df84b81552 100644
--- a/arch/arm64/boot/dts/rockchip/rk3368-px5-evb.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3368-px5-evb.dts
@@ -30,7 +30,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pwr_key>;
 
-		power {
+		key-power {
 			gpios = <&gpio0 RK_PA2 GPIO_ACTIVE_LOW>;
 			label = "GPIO Power";
 			linux,code = <KEY_POWER>;
diff --git a/arch/arm64/boot/dts/rockchip/rk3368-r88.dts b/arch/arm64/boot/dts/rockchip/rk3368-r88.dts
index 959d3cc801f2..38d757c00548 100644
--- a/arch/arm64/boot/dts/rockchip/rk3368-r88.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3368-r88.dts
@@ -37,7 +37,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pwr_key>;
 
-		power {
+		key-power {
 			wakeup-source;
 			gpios = <&gpio0 RK_PA2 GPIO_ACTIVE_LOW>;
 			label = "GPIO Power";
diff --git a/arch/arm64/boot/dts/rockchip/rk3368.dtsi b/arch/arm64/boot/dts/rockchip/rk3368.dtsi
index c99da90328e9..a4c5aaf1f457 100644
--- a/arch/arm64/boot/dts/rockchip/rk3368.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3368.dtsi
@@ -747,6 +747,8 @@
 	cru: clock-controller@ff760000 {
 		compatible = "rockchip,rk3368-cru";
 		reg = <0x0 0xff760000 0x0 0x1000>;
+		clocks = <&xin24m>;
+		clock-names = "xin24m";
 		rockchip,grf = <&grf>;
 		#clock-cells = <1>;
 		#reset-cells = <1>;
@@ -1082,7 +1084,7 @@
 
 		gmac {
 			rgmii_pins: rgmii-pins {
-				rockchip,pins =	<3 RK_PC6 1 &pcfg_pull_none>,
+				rockchip,pins = <3 RK_PC6 1 &pcfg_pull_none>,
 						<3 RK_PD0 1 &pcfg_pull_none>,
 						<3 RK_PC3 1 &pcfg_pull_none>,
 						<3 RK_PB0 1 &pcfg_pull_none_12ma>,
@@ -1100,7 +1102,7 @@
 			};
 
 			rmii_pins: rmii-pins {
-				rockchip,pins =	<3 RK_PC6 1 &pcfg_pull_none>,
+				rockchip,pins = <3 RK_PC6 1 &pcfg_pull_none>,
 						<3 RK_PD0 1 &pcfg_pull_none>,
 						<3 RK_PC3 1 &pcfg_pull_none>,
 						<3 RK_PB0 1 &pcfg_pull_none_12ma>,
@@ -1255,7 +1257,7 @@
 
 		spdif {
 			spdif_tx: spdif-tx {
-				rockchip,pins =	<2 RK_PC7 1 &pcfg_pull_none>;
+				rockchip,pins = <2 RK_PC7 1 &pcfg_pull_none>;
 			};
 		};
 
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-eaidk-610.dts b/arch/arm64/boot/dts/rockchip/rk3399-eaidk-610.dts
new file mode 100644
index 000000000000..d1f343345f67
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3399-eaidk-610.dts
@@ -0,0 +1,939 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2022 Fuzhou Rockchip Electronics Co., Ltd.
+ */
+
+/dts-v1/;
+#include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/pwm/pwm.h>
+#include <dt-bindings/usb/pd.h>
+#include "rk3399.dtsi"
+#include "rk3399-opp.dtsi"
+
+/ {
+	model = "OPEN AI LAB EAIDK-610";
+	compatible = "openailab,eaidk-610", "rockchip,rk3399";
+
+	aliases {
+		mmc0 = &sdio0;
+		mmc1 = &sdmmc;
+		mmc2 = &sdhci;
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm0 0 25000 0>;
+		brightness-levels = <
+			  0   1   2   3   4   5   6   7
+			  8   9  10  11  12  13  14  15
+			 16  17  18  19  20  21  22  23
+			 24  25  26  27  28  29  30  31
+			 32  33  34  35  36  37  38  39
+			 40  41  42  43  44  45  46  47
+			 48  49  50  51  52  53  54  55
+			 56  57  58  59  60  61  62  63
+			 64  65  66  67  68  69  70  71
+			 72  73  74  75  76  77  78  79
+			 80  81  82  83  84  85  86  87
+			 88  89  90  91  92  93  94  95
+			 96  97  98  99 100 101 102 103
+			104 105 106 107 108 109 110 111
+			112 113 114 115 116 117 118 119
+			120 121 122 123 124 125 126 127
+			128 129 130 131 132 133 134 135
+			136 137 138 139 140 141 142 143
+			144 145 146 147 148 149 150 151
+			152 153 154 155 156 157 158 159
+			160 161 162 163 164 165 166 167
+			168 169 170 171 172 173 174 175
+			176 177 178 179 180 181 182 183
+			184 185 186 187 188 189 190 191
+			192 193 194 195 196 197 198 199
+			200 201 202 203 204 205 206 207
+			208 209 210 211 212 213 214 215
+			216 217 218 219 220 221 222 223
+			224 225 226 227 228 229 230 231
+			232 233 234 235 236 237 238 239
+			240 241 242 243 244 245 246 247
+			248 249 250 251 252 253 254 255>;
+		default-brightness-level = <200>;
+	};
+
+	clkin_gmac: external-gmac-clock {
+		compatible = "fixed-clock";
+		clock-frequency = <125000000>;
+		clock-output-names = "clkin_gmac";
+		#clock-cells = <0>;
+	};
+
+	dc_12v: dc-12v {
+		compatible = "regulator-fixed";
+		regulator-name = "dc_12v";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		autorepeat;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pwrbtn>;
+
+		key-power {
+			debounce-interval = <100>;
+			gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_LOW>;
+			label = "GPIO Key Power";
+			linux,code = <KEY_POWER>;
+			wakeup-source;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&work_led_pin>, <&user_led_pin>,
+			    <&heartbeat_led_pin>, <&wlan_active_led_pin>,
+			    <&bt_active_led_pin>;
+
+		work_led: led-0 {
+			label = "blue:work";
+			default-state = "on";
+			gpios = <&gpio0 RK_PA2 GPIO_ACTIVE_HIGH>;
+		};
+
+		user_led: led-1 {
+			label = "read:user";
+			default-state = "off";
+			gpios = <&gpio0 RK_PB4 GPIO_ACTIVE_HIGH>;
+		};
+
+		heartbeat_led: led-2 {
+			label = "green:heartbeat";
+			linux,default-trigger = "heartbeat";
+			gpios = <&gpio0 RK_PB5 GPIO_ACTIVE_HIGH>;
+		};
+
+		wlan_active_led: led-3 {
+			label = "yellow:wlan";
+			gpios = <&gpio2 RK_PD3 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "phy0tx";
+			default-state = "off";
+		};
+
+		bt_active_led: led-4 {
+			label = "blue:bt";
+			gpios = <&gpio2 RK_PD4 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "hci0-power";
+			default-state = "off";
+		};
+	};
+
+	rt5651-sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "realtek,rt5651-codec";
+		simple-audio-card,format = "i2s";
+		simple-audio-card,mclk-fs = <256>;
+		simple-audio-card,widgets =
+			"Microphone", "Mic Jack",
+			"Headphone", "Headphone Jack";
+		simple-audio-card,routing =
+			"Mic Jack", "MICBIAS1",
+			"IN1P", "Mic Jack",
+			"Headphone Jack", "HPOL",
+			"Headphone Jack", "HPOR";
+		simple-audio-card,cpu {
+			sound-dai = <&i2s1>;
+		};
+		simple-audio-card,codec {
+			sound-dai = <&rt5651>;
+		};
+	};
+
+	sdio_pwrseq: sdio-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		clocks = <&rk808 1>;
+		clock-names = "ext_clock";
+		pinctrl-names = "default";
+		pinctrl-0 = <&wifi_enable_h>;
+
+		/*
+		 * On the module itself this is one of these (depending
+		 * on the actual card populated):
+		 * - SDIO_RESET_L_WL_REG_ON
+		 * - PDN (power down when low)
+		 */
+		reset-gpios = <&gpio0 RK_PB2 GPIO_ACTIVE_LOW>;
+	};
+
+	/* switched by pmic_sleep */
+	vcc1v8_s3: vcca1v8_s3: vcc1v8-s3 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc1v8_s3";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vcc_1v8>;
+	};
+
+	vcc3v3_sys: vcc3v3-sys {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3_sys";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&dc_12v>;
+	};
+
+	vcc5v0_sys: vcc5v0-sys {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc5v0_sys";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&dc_12v>;
+	};
+
+	/* For USB3.0 Port1/2 */
+	vcc5v0_host1: vcc5v0-host1-regulator {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio0 RK_PA6 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vcc5v0_host1_en>;
+		regulator-name = "vcc5v0_host1";
+		regulator-always-on;
+		vin-supply = <&vcc5v0_sys>;
+	};
+
+	/* For USB2.0 Port1/2 */
+	vcc5v0_host3: vcc5v0-host3-regulator {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio0 RK_PB0 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vcc5v0_host3_en>;
+		regulator-name = "vcc5v0_host3";
+		regulator-always-on;
+		vin-supply = <&vcc5v0_sys>;
+	};
+
+	vcc5v0_typec: vcc5v0-typec-regulator {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio4 RK_PC5 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vcc5v0_typec_en>;
+		regulator-name = "vcc5v0_typec";
+		regulator-always-on;
+		vin-supply = <&vcc3v3_sys>;
+	};
+
+	vdd_log: vdd-log {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_log";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <900000>;
+		regulator-max-microvolt = <900000>;
+	};
+};
+
+&cpu_l0 {
+	cpu-supply = <&vdd_cpu_l>;
+};
+
+&cpu_l1 {
+	cpu-supply = <&vdd_cpu_l>;
+};
+
+&cpu_l2 {
+	cpu-supply = <&vdd_cpu_l>;
+};
+
+&cpu_l3 {
+	cpu-supply = <&vdd_cpu_l>;
+};
+
+&cpu_b0 {
+	cpu-supply = <&vdd_cpu_b>;
+};
+
+&cpu_b1 {
+	cpu-supply = <&vdd_cpu_b>;
+};
+
+&emmc_phy {
+	status = "okay";
+};
+
+&gmac {
+	assigned-clocks = <&cru SCLK_RMII_SRC>;
+	assigned-clock-parents = <&clkin_gmac>;
+	clock_in_out = "input";
+	phy-supply = <&vcc_lan>;
+	phy-mode = "rgmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&rgmii_pins>;
+	snps,reset-gpio = <&gpio3 RK_PB7 GPIO_ACTIVE_LOW>;
+	snps,reset-active-low;
+	snps,reset-delays-us = <0 10000 50000>;
+	tx_delay = <0x28>;
+	rx_delay = <0x11>;
+	status = "okay";
+};
+
+&gpu {
+	mali-supply = <&vdd_gpu>;
+	status = "okay";
+};
+
+&hdmi {
+	ddc-i2c-bus = <&i2c3>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&hdmi_cec>;
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	rk808: pmic@1b {
+		compatible = "rockchip,rk808";
+		reg = <0x1b>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <21 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_int_l>;
+		rockchip,system-power-controller;
+		wakeup-source;
+		#clock-cells = <1>;
+		clock-output-names = "xin32k", "rk808-clkout2";
+
+		vcc1-supply = <&vcc3v3_sys>;
+		vcc2-supply = <&vcc3v3_sys>;
+		vcc3-supply = <&vcc3v3_sys>;
+		vcc4-supply = <&vcc3v3_sys>;
+		vcc6-supply = <&vcc3v3_sys>;
+		vcc7-supply = <&vcc3v3_sys>;
+		vcc8-supply = <&vcc3v3_sys>;
+		vcc9-supply = <&vcc3v3_sys>;
+		vcc10-supply = <&vcc3v3_sys>;
+		vcc11-supply = <&vcc3v3_sys>;
+		vcc12-supply = <&vcc3v3_sys>;
+		vddio-supply = <&vcc_3v0>;
+
+		regulators {
+			vdd_center: DCDC_REG1 {
+				regulator-name = "vdd_center";
+				regulator-min-microvolt = <750000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-ramp-delay = <6001>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdd_cpu_l: DCDC_REG2 {
+				regulator-name = "vdd_cpu_l";
+				regulator-min-microvolt = <750000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-ramp-delay = <6001>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_ddr: DCDC_REG3 {
+				regulator-name = "vcc_ddr";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vcc_1v8: DCDC_REG4 {
+				regulator-name = "vcc_1v8";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vcc1v8_dvp: LDO_REG1 {
+				regulator-name = "vcc1v8_dvp";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc2v8_dvp: LDO_REG2 {
+				regulator-name = "vcc2v8_dvp";
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc1v8_pmu: LDO_REG3 {
+				regulator-name = "vcc1v8_pmu";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vcc_sdio: LDO_REG4 {
+				regulator-name = "vcc_sdio";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3000000>;
+				};
+			};
+
+			vcca3v0_codec: LDO_REG5 {
+				regulator-name = "vcca3v0_codec";
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_1v5: LDO_REG6 {
+				regulator-name = "vcc_1v5";
+				regulator-min-microvolt = <1500000>;
+				regulator-max-microvolt = <1500000>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1500000>;
+				};
+			};
+
+			vcca1v8_codec: LDO_REG7 {
+				regulator-name = "vcca1v8_codec";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_3v0: LDO_REG8 {
+				regulator-name = "vcc_3v0";
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3000000>;
+				};
+			};
+
+			vcc3v3_s3: vcc_lan: SWITCH_REG1 {
+				regulator-name = "vcc3v3_s3";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc3v3_s0: SWITCH_REG2 {
+				regulator-name = "vcc3v3_s0";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+		};
+	};
+
+	vdd_cpu_b: regulator@40 {
+		compatible = "silergy,syr827";
+		reg = <0x40>;
+		fcs,suspend-voltage-selector = <1>;
+		regulator-name = "vdd_cpu_b";
+		pinctrl-names = "default";
+		pinctrl-0 = <&vsel1_pin>;
+		regulator-min-microvolt = <712500>;
+		regulator-max-microvolt = <1500000>;
+		regulator-ramp-delay = <1000>;
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&vcc3v3_sys>;
+
+		regulator-state-mem {
+			regulator-off-in-suspend;
+		};
+	};
+
+	vdd_gpu: regulator@41 {
+		compatible = "silergy,syr828";
+		reg = <0x41>;
+		fcs,suspend-voltage-selector = <1>;
+		regulator-name = "vdd_gpu";
+		pinctrl-names = "default";
+		pinctrl-0 = <&vsel2_pin>;
+		regulator-min-microvolt = <712500>;
+		regulator-max-microvolt = <1500000>;
+		regulator-ramp-delay = <1000>;
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&vcc3v3_sys>;
+
+		regulator-state-mem {
+			regulator-off-in-suspend;
+		};
+	};
+};
+
+&i2c1 {
+	i2c-scl-rising-time-ns = <300>;
+	i2c-scl-falling-time-ns = <15>;
+	status = "okay";
+
+	rt5651: audio-codec@1a {
+		compatible = "rockchip,rt5651";
+		reg = <0x1a>;
+		clocks = <&cru SCLK_I2S_8CH_OUT>;
+		clock-names = "mclk";
+		hp-det-gpio = <&gpio4 RK_PD4 GPIO_ACTIVE_LOW>;
+		spk-con-gpio = <&gpio0 RK_PB3 GPIO_ACTIVE_HIGH>;
+		#sound-dai-cells = <0>;
+	};
+
+};
+
+&i2c3 {
+	i2c-scl-rising-time-ns = <450>;
+	i2c-scl-falling-time-ns = <15>;
+	status = "okay";
+};
+
+&i2c4 {
+	i2c-scl-rising-time-ns = <600>;
+	i2c-scl-falling-time-ns = <20>;
+	status = "okay";
+
+	fusb0: typec-portc@22 {
+		compatible = "fcs,fusb302";
+		reg = <0x22>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <RK_PA2 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&fusb0_int>;
+		vbus-supply = <&vcc5v0_typec>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				usbc0_role_sw: endpoint@0 {
+					remote-endpoint = <&dwc3_0_role_switch>;
+				};
+			};
+		};
+
+		connector {
+			compatible = "usb-c-connector";
+			data-role = "dual";
+			label = "USB-C";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+
+					usbc_hs: endpoint {
+						remote-endpoint = <&u2phy0_typec_hs>;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+
+					usbc_ss: endpoint {
+						remote-endpoint = <&tcphy0_typec_ss>;
+					};
+				};
+			};
+		};
+	};
+};
+
+&i2s1 {
+	rockchip,playback-channels = <2>;
+	rockchip,capture-channels = <2>;
+	status = "okay";
+};
+
+&i2s2 {
+	status = "okay";
+};
+
+&io_domains {
+	status = "okay";
+
+	audio-supply = <&vcca1v8_codec>;
+	bt656-supply = <&vcc_3v0>;
+	gpio1830-supply = <&vcc_3v0>;
+	sdmmc-supply = <&vcc_sdio>;
+};
+
+&pmu_io_domains {
+	status = "okay";
+
+	pmu1830-supply = <&vcc_3v0>;
+};
+
+&pinctrl {
+	buttons {
+		pwrbtn: pwrbtn {
+			rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	bt {
+		bt_enable_h: bt-enable-h {
+			rockchip,pins = <0 RK_PB1 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		bt_host_wake_l: bt-host-wake-l {
+			rockchip,pins = <0 RK_PA4 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		bt_wake_l: bt-wake-l {
+			rockchip,pins = <2 RK_PD2 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	fusb302x {
+		fusb0_int: fusb0-int {
+			rockchip,pins = <1 RK_PA2 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	lcd-panel {
+		lcd_panel_reset: lcd-panel-reset {
+			rockchip,pins = <4 RK_PD6 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	leds {
+		work_led_pin: work-led-pin {
+			rockchip,pins = <0 RK_PA2 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		user_led_pin: user-led-pin {
+			rockchip,pins = <0 RK_PB4 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		heartbeat_led_pin: heartbeat-led-pin {
+			rockchip,pins = <0 RK_PB5 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		wlan_active_led_pin: wlan-led-pin {
+			rockchip,pins = <2 RK_PD3 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		bt_active_led_pin: bt-led-pin {
+			rockchip,pins = <2 RK_PD4 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+
+	};
+
+	pmic {
+		pmic_int_l: pmic-int-l {
+			rockchip,pins = <1 RK_PC5 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+
+		vsel1_pin: vsel1-pin {
+			rockchip,pins = <1 RK_PC1 RK_FUNC_GPIO &pcfg_pull_down>;
+		};
+
+		vsel2_pin: vsel2-pin {
+			rockchip,pins = <1 RK_PB6 RK_FUNC_GPIO &pcfg_pull_down>;
+		};
+	};
+
+	rt5651 {
+		rt5651_hpcon: rt5640-hpcon {
+			rockchip,pins = <4 RK_PD4 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	sdio-pwrseq {
+		wifi_enable_h: wifi-enable-h {
+			rockchip,pins = <0 RK_PB2 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	usb-typec {
+		vcc5v0_typec_en: vcc5v0_typec_en {
+			rockchip,pins = <4 RK_PC5 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	usb2 {
+		vcc5v0_host3_en: vcc5v0-host3-en {
+			rockchip,pins = <0 RK_PB0 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		vcc5v0_host1_en: vcc5v0-host1-en {
+			rockchip,pins = <0 RK_PA6 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	wifi {
+		wifi_host_wake_l: wifi-host-wake-l {
+			rockchip,pins = <0 RK_PA3 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+};
+
+&pwm0 {
+	status = "okay";
+};
+
+&saradc {
+	vref-supply = <&vcca1v8_s3>;
+	status = "okay";
+};
+
+&sdio0 {
+	/* WiFi & BT combo module AMPAK AP6255 */
+	#address-cells = <1>;
+	#size-cells = <0>;
+	bus-width = <4>;
+	clock-frequency = <50000000>;
+	cap-sdio-irq;
+	cap-sd-highspeed;
+	keep-power-in-suspend;
+	mmc-pwrseq = <&sdio_pwrseq>;
+	non-removable;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdio0_bus4 &sdio0_cmd &sdio0_clk>;
+	sd-uhs-sdr104;
+	status = "okay";
+
+	brcmf: wifi@1 {
+		compatible = "brcm,bcm4329-fmac";
+		reg = <1>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <RK_PA3 GPIO_ACTIVE_HIGH>;
+		interrupt-names = "host-wake";
+		pinctrl-names = "default";
+		pinctrl-0 = <&wifi_host_wake_l>;
+	};
+};
+
+&sdmmc {
+	bus-width = <4>;
+	cap-mmc-highspeed;
+	cap-sd-highspeed;
+	cd-gpios = <&gpio0 RK_PA7 GPIO_ACTIVE_LOW>;
+	disable-wp;
+	max-frequency = <150000000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_bus4>;
+	status = "okay";
+};
+
+&sdhci {
+	bus-width = <8>;
+	non-removable;
+	status = "okay";
+};
+
+&tcphy0 {
+	status = "okay";
+};
+
+&tcphy0_usb3 {
+	orientation-switch;
+	port {
+		tcphy0_typec_ss: endpoint {
+			remote-endpoint = <&usbc_ss>;
+		};
+	};
+};
+
+&tcphy1 {
+	status = "okay";
+};
+
+&tsadc {
+	/* tshut mode 0:CRU 1:GPIO */
+	rockchip,hw-tshut-mode = <1>;
+	/* tshut polarity 0:LOW 1:HIGH */
+	rockchip,hw-tshut-polarity = <1>;
+	status = "okay";
+};
+
+&u2phy0 {
+	status = "okay";
+
+	u2phy0_otg: otg-port {
+		status = "okay";
+	};
+
+	u2phy0_host: host-port {
+		phy-supply = <&vcc5v0_host3>;
+		status = "okay";
+	};
+
+	port {
+		u2phy0_typec_hs: endpoint {
+			remote-endpoint = <&usbc_hs>;
+		};
+	};
+};
+
+&u2phy1 {
+	status = "okay";
+
+	u2phy1_otg: otg-port {
+		status = "okay";
+	};
+
+	u2phy1_host: host-port {
+		phy-supply = <&vcc5v0_host3>;
+		status = "okay";
+	};
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_xfer &uart0_cts &uart0_rts>;
+	status = "okay";
+
+	bluetooth {
+		compatible = "brcm,bcm4345c5";
+		clocks = <&rk808 1>;
+		clock-names = "lpo";
+		device-wakeup-gpios = <&gpio2 RK_PD2 GPIO_ACTIVE_HIGH>;
+		host-wakeup-gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_HIGH>;
+		shutdown-gpios = <&gpio0 RK_PB1 GPIO_ACTIVE_HIGH>;
+		max-speed = <1500000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&bt_host_wake_l &bt_wake_l &bt_enable_h>;
+		vbat-supply = <&vcc3v3_sys>;
+		vddio-supply = <&vcc_1v8>;
+	};
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&usb_host0_ehci {
+	status = "okay";
+};
+
+&usb_host0_ohci {
+	status = "okay";
+};
+
+&usb_host1_ehci {
+	status = "okay";
+};
+
+&usb_host1_ohci {
+	status = "okay";
+};
+
+&usbdrd3_0 {
+	status = "okay";
+};
+
+&usbdrd_dwc3_0 {
+	status = "okay";
+	usb-role-switch;
+
+	port {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		dwc3_0_role_switch: endpoint@0 {
+			reg = <0>;
+			remote-endpoint = <&usbc0_role_sw>;
+		};
+	};
+};
+
+&usbdrd3_1 {
+	status = "okay";
+};
+
+&usbdrd_dwc3_1 {
+	status = "okay";
+	dr_mode = "host";
+};
+
+&vopb {
+	status = "okay";
+};
+
+&vopb_mmu {
+	status = "okay";
+};
+
+&vopl {
+	status = "okay";
+};
+
+&vopl_mmu {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-evb.dts b/arch/arm64/boot/dts/rockchip/rk3399-evb.dts
index 7b717ebec8ff..3d1e126b553f 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-evb.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3399-evb.dts
@@ -55,7 +55,7 @@
 	};
 
 	edp_panel: edp-panel {
-		compatible ="lg,lp079qx1-sp0v";
+		compatible = "lg,lp079qx1-sp0v";
 		backlight = <&backlight>;
 		enable-gpios = <&gpio1 RK_PB5 GPIO_ACTIVE_HIGH>;
 		power-supply = <&vcc3v3_s0>;
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-firefly.dts b/arch/arm64/boot/dts/rockchip/rk3399-firefly.dts
index c4dd2a6b4836..c5db64f3e124 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-firefly.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3399-firefly.dts
@@ -5,6 +5,7 @@
 
 /dts-v1/;
 #include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/pwm/pwm.h>
 #include <dt-bindings/usb/pd.h>
 #include "rk3399.dtsi"
@@ -86,7 +87,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pwrbtn>;
 
-		power {
+		key-power {
 			debounce-interval = <100>;
 			gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_LOW>;
 			label = "GPIO Key Power";
@@ -245,12 +246,12 @@
 	vdd_log: vdd-log {
 		compatible = "pwm-regulator";
 		pwms = <&pwm2 0 25000 1>;
+		pwm-supply = <&vcc_sys>;
 		regulator-name = "vdd_log";
 		regulator-always-on;
 		regulator-boot-on;
 		regulator-min-microvolt = <430000>;
 		regulator-max-microvolt = <1400000>;
-		vin-supply = <&vcc_sys>;
 	};
 };
 
@@ -298,6 +299,11 @@
 	status = "okay";
 };
 
+&gpu {
+	mali-supply = <&vdd_gpu>;
+	status = "okay";
+};
+
 &hdmi {
 	ddc-i2c-bus = <&i2c3>;
 	pinctrl-names = "default";
@@ -770,8 +776,8 @@
 	sd-uhs-sdr104;
 
 	/* Power supply */
-	vqmmc-supply = &vcc1v8_s3;	/* IO line */
-	vmmc-supply = &vcc_sdio;	/* card's power */
+	vqmmc-supply = <&vcc1v8_s3>;	/* IO line */
+	vmmc-supply = <&vcc_sdio>;	/* card's power */
 
 	#address-cells = <1>;
 	#size-cells = <0>;
@@ -781,7 +787,7 @@
 		reg = <1>;
 		compatible = "brcm,bcm4329-fmac";
 		interrupt-parent = <&gpio0>;
-		interrupts = <RK_PA3 GPIO_ACTIVE_HIGH>;
+		interrupts = <RK_PA3 IRQ_TYPE_LEVEL_HIGH>;
 		interrupt-names = "host-wake";
 		brcm,drive-strength = <5>;
 		pinctrl-names = "default";
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-gru-bob.dts b/arch/arm64/boot/dts/rockchip/rk3399-gru-bob.dts
index 31ebb4e5fd33..0f9cc042d9bf 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-gru-bob.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3399-gru-bob.dts
@@ -88,3 +88,8 @@
 		};
 	};
 };
+
+&wlan_host_wake_l {
+	/* Kevin has an external pull up, but Bob does not. */
+	rockchip,pins = <0 RK_PB0 RK_FUNC_GPIO &pcfg_pull_up>;
+};
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-gru-chromebook.dtsi b/arch/arm64/boot/dts/rockchip/rk3399-gru-chromebook.dtsi
index 9b2c679f5eca..ee6095baba4d 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-gru-chromebook.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3399-gru-chromebook.dtsi
@@ -206,7 +206,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&bt_host_wake_l>;
 
-		wake_on_bt: wake-on-bt {
+		wake_on_bt: key-wake-on-bt {
 			label = "Wake-on-Bluetooth";
 			gpios = <&gpio0 3 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_WAKEUP>;
@@ -234,9 +234,24 @@
 	extcon = <&usbc_extcon0>, <&usbc_extcon1>;
 };
 
+&dmc {
+	center-supply = <&ppvar_centerlogic>;
+	rockchip,pd-idle-dis-freq-hz = <800000000>;
+	rockchip,sr-idle-dis-freq-hz = <800000000>;
+	rockchip,sr-mc-gate-idle-dis-freq-hz = <800000000>;
+};
+
 &edp {
 	status = "okay";
 
+	/*
+	 * eDP PHY/clk don't sync reliably at anything other than 24 MHz. Only
+	 * set this here, because rk3399-gru.dtsi ensures we can generate this
+	 * off GPLL=600MHz, whereas some other RK3399 boards may not.
+	 */
+	assigned-clocks = <&cru PCLK_EDP>;
+	assigned-clock-rates = <24000000>;
+
 	ports {
 		edp_out: port@1 {
 			reg = <1>;
@@ -462,7 +477,7 @@ ap_i2c_tp: &i2c5 {
 };
 
 &cros_ec {
-	cros_ec_pwm: ec-pwm {
+	cros_ec_pwm: pwm {
 		compatible = "google,cros-ec-pwm";
 		#pwm-cells = <1>;
 	};
@@ -571,6 +586,7 @@ ap_i2c_tp: &i2c5 {
 	};
 
 	wlan_host_wake_l: wlan-host-wake-l {
+		/* Kevin has an external pull up, but Bob does not */
 		rockchip,pins = <0 RK_PB0 RK_FUNC_GPIO &pcfg_pull_none>;
 	};
 };
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-gru-kevin.dts b/arch/arm64/boot/dts/rockchip/rk3399-gru-kevin.dts
index 6863689df06f..2cc9b3386c16 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-gru-kevin.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3399-gru-kevin.dts
@@ -92,7 +92,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&bt_host_wake_l>, <&cpu1_pen_eject>;
 
-	pen-insert {
+	switch-pen-insert {
 		label = "Pen Insert";
 		/* Insert = low, eject = high */
 		gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-gru-scarlet-inx.dts b/arch/arm64/boot/dts/rockchip/rk3399-gru-scarlet-inx.dts
index 2d721a974790..5d1879033e7c 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-gru-scarlet-inx.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3399-gru-scarlet-inx.dts
@@ -11,17 +11,29 @@
 
 / {
 	model = "Google Scarlet";
-	compatible = "google,scarlet-rev15-sku6", "google,scarlet-rev15",
+	compatible = "google,scarlet-rev15-sku2", "google,scarlet-rev15-sku4",
+		     "google,scarlet-rev15-sku6", "google,scarlet-rev15",
+		     "google,scarlet-rev14-sku2", "google,scarlet-rev14-sku4",
 		     "google,scarlet-rev14-sku6", "google,scarlet-rev14",
+		     "google,scarlet-rev13-sku2", "google,scarlet-rev13-sku4",
 		     "google,scarlet-rev13-sku6", "google,scarlet-rev13",
+		     "google,scarlet-rev12-sku2", "google,scarlet-rev12-sku4",
 		     "google,scarlet-rev12-sku6", "google,scarlet-rev12",
+		     "google,scarlet-rev11-sku2", "google,scarlet-rev11-sku4",
 		     "google,scarlet-rev11-sku6", "google,scarlet-rev11",
+		     "google,scarlet-rev10-sku2", "google,scarlet-rev10-sku4",
 		     "google,scarlet-rev10-sku6", "google,scarlet-rev10",
+		     "google,scarlet-rev9-sku2",  "google,scarlet-rev9-sku4",
 		     "google,scarlet-rev9-sku6",  "google,scarlet-rev9",
+		     "google,scarlet-rev8-sku2",  "google,scarlet-rev8-sku4",
 		     "google,scarlet-rev8-sku6",  "google,scarlet-rev8",
+		     "google,scarlet-rev7-sku2",  "google,scarlet-rev7-sku4",
 		     "google,scarlet-rev7-sku6",  "google,scarlet-rev7",
+		     "google,scarlet-rev6-sku2",  "google,scarlet-rev6-sku4",
 		     "google,scarlet-rev6-sku6",  "google,scarlet-rev6",
+		     "google,scarlet-rev5-sku2",  "google,scarlet-rev5-sku4",
 		     "google,scarlet-rev5-sku6",  "google,scarlet-rev5",
+		     "google,scarlet-rev4-sku2",  "google,scarlet-rev4-sku4",
 		     "google,scarlet-rev4-sku6",  "google,scarlet-rev4",
 		     "google,scarlet", "google,gru", "rockchip,rk3399";
 };
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-gru-scarlet.dtsi b/arch/arm64/boot/dts/rockchip/rk3399-gru-scarlet.dtsi
index a9817b3d7edc..ed3348b558f8 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-gru-scarlet.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3399-gru-scarlet.dtsi
@@ -183,7 +183,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pen_eject_odl>;
 
-		pen-insert {
+		switch-pen-insert {
 			label = "Pen Insert";
 			/* Insert = low, eject = high */
 			gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
@@ -376,7 +376,8 @@ camera: &i2c7 {
 		<&cru ACLK_VIO>,
 		<&cru ACLK_GIC_PRE>,
 		<&cru PCLK_DDR>,
-		<&cru ACLK_HDCP>;
+		<&cru ACLK_HDCP>,
+		<&cru ACLK_VDU>;
 	assigned-clock-rates =
 		<600000000>, <1600000000>,
 		<1000000000>,
@@ -388,9 +389,22 @@ camera: &i2c7 {
 		<400000000>,
 		<200000000>,
 		<200000000>,
+		<400000000>,
 		<400000000>;
 };
 
+/* The center supply is fixed to .9V on scarlet */
+&dmc {
+	center-supply = <&pp900_s0>;
+};
+
+/* We don't need .925 V for 928 MHz on scarlet */
+&dmc_opp_table {
+	opp03 {
+		opp-microvolt = <900000>;
+	};
+};
+
 &gpio0 {
 	gpio-line-names = /* GPIO0 A 0-7 */
 			  "CLK_32K_AP",
@@ -754,6 +768,16 @@ camera: &i2c7 {
 		<4 RK_PA0 1 &pcfg_pull_none_6ma>;
 };
 
+&i2s0_8ch_bus_bclk_off {
+	rockchip,pins =
+		<3 RK_PD0 RK_FUNC_GPIO &pcfg_pull_none_6ma>,
+		<3 RK_PD1 1 &pcfg_pull_none_6ma>,
+		<3 RK_PD2 1 &pcfg_pull_none_6ma>,
+		<3 RK_PD3 1 &pcfg_pull_none_6ma>,
+		<3 RK_PD7 1 &pcfg_pull_none_6ma>,
+		<4 RK_PA0 1 &pcfg_pull_none_6ma>;
+};
+
 /* there is no external pull up, so need to set this pin pull up */
 &sdmmc_cd_pin {
 	rockchip,pins = <1 RK_PB3 RK_FUNC_GPIO &pcfg_pull_up>;
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-gru.dtsi b/arch/arm64/boot/dts/rockchip/rk3399-gru.dtsi
index 45a5ae5d2027..23bfba86daab 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-gru.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3399-gru.dtsi
@@ -286,7 +286,7 @@
 
 	sound: sound {
 		compatible = "rockchip,rk3399-gru-sound";
-		rockchip,cpu = <&i2s0 &i2s2>;
+		rockchip,cpu = <&i2s0 &spdif>;
 	};
 };
 
@@ -373,6 +373,34 @@
 		<200000000>;
 };
 
+&dfi {
+	status = "okay";
+};
+
+&dmc {
+	status = "okay";
+
+	rockchip,pd-idle-ns = <160>;
+	rockchip,sr-idle-ns = <10240>;
+	rockchip,sr-mc-gate-idle-ns = <40960>;
+	rockchip,srpd-lite-idle-ns = <61440>;
+	rockchip,standby-idle-ns = <81920>;
+
+	rockchip,ddr3_odt_dis_freq = <666000000>;
+	rockchip,lpddr3_odt_dis_freq = <666000000>;
+	rockchip,lpddr4_odt_dis_freq = <666000000>;
+
+	rockchip,sr-mc-gate-idle-dis-freq-hz = <1000000000>;
+	rockchip,srpd-lite-idle-dis-freq-hz = <0>;
+	rockchip,standby-idle-dis-freq-hz = <928000000>;
+};
+
+&dmc_opp_table {
+	opp03 {
+		opp-suspend;
+	};
+};
+
 &emmc_phy {
 	status = "okay";
 };
@@ -437,10 +465,6 @@ ap_i2c_audio: &i2c8 {
 	status = "okay";
 };
 
-&i2s2 {
-	status = "okay";
-};
-
 &io_domains {
 	status = "okay";
 
@@ -537,6 +561,17 @@ ap_i2c_audio: &i2c8 {
 	vqmmc-supply = <&ppvar_sd_card_io>;
 };
 
+&spdif {
+	status = "okay";
+
+	/*
+	 * SPDIF is routed internally to DP; we either don't use these pins, or
+	 * mux them to something else.
+	 */
+	/delete-property/ pinctrl-0;
+	/delete-property/ pinctrl-names;
+};
+
 &spi1 {
 	status = "okay";
 
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-hugsun-x99.dts b/arch/arm64/boot/dts/rockchip/rk3399-hugsun-x99.dts
index bee45c17e2ca..7af27e8216f1 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-hugsun-x99.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3399-hugsun-x99.dts
@@ -2,6 +2,7 @@
 /dts-v1/;
 #include <dt-bindings/pwm/pwm.h>
 #include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
 #include "rk3399.dtsi"
 #include "rk3399-opp.dtsi"
 
@@ -629,7 +630,7 @@
 		compatible = "brcm,bcm4329-fmac";
 		reg = <1>;
 		interrupt-parent = <&gpio0>;
-		interrupts = <RK_PA3 GPIO_ACTIVE_HIGH>;
+		interrupts = <RK_PA3 IRQ_TYPE_LEVEL_HIGH>;
 		interrupt-names = "host-wake";
 		pinctrl-names = "default";
 		pinctrl-0 = <&wifi_host_wake_l>;
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-khadas-edge.dtsi b/arch/arm64/boot/dts/rockchip/rk3399-khadas-edge.dtsi
index d5c7648c841d..2a332763c35c 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-khadas-edge.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3399-khadas-edge.dtsi
@@ -6,6 +6,7 @@
 
 /dts-v1/;
 #include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/pwm/pwm.h>
 #include "rk3399.dtsi"
 #include "rk3399-opp.dtsi"
@@ -80,12 +81,12 @@
 	vdd_log: vdd-log {
 		compatible = "pwm-regulator";
 		pwms = <&pwm2 0 25000 1>;
+		pwm-supply = <&vsys_3v3>;
 		regulator-name = "vdd_log";
 		regulator-always-on;
 		regulator-boot-on;
 		regulator-min-microvolt = <800000>;
 		regulator-max-microvolt = <1400000>;
-		vin-supply = <&vsys_3v3>;
 	};
 
 	vsys: vsys {
@@ -135,7 +136,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pwrbtn>;
 
-		power {
+		key-power {
 			debounce-interval = <100>;
 			gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_LOW>;
 			label = "GPIO Key Power";
@@ -682,7 +683,7 @@
 		reg = <1>;
 		compatible = "brcm,bcm4329-fmac";
 		interrupt-parent = <&gpio0>;
-		interrupts = <RK_PA3 GPIO_ACTIVE_HIGH>;
+		interrupts = <RK_PA3 IRQ_TYPE_LEVEL_HIGH>;
 		interrupt-names = "host-wake";
 		brcm,drive-strength = <5>;
 		pinctrl-names = "default";
@@ -705,7 +706,6 @@
 &sdhci {
 	bus-width = <8>;
 	mmc-hs400-1_8v;
-	mmc-hs400-enhanced-strobe;
 	non-removable;
 	status = "okay";
 };
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-kobol-helios64.dts b/arch/arm64/boot/dts/rockchip/rk3399-kobol-helios64.dts
index 63c7681843da..1eb287a3f8c0 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-kobol-helios64.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3399-kobol-helios64.dts
@@ -89,6 +89,30 @@
 		};
 	};
 
+	hdd_a_power: hdd-a-power {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio1 RK_PA0 GPIO_ACTIVE_HIGH>;
+		pinctrl-0 = <&hdd_a_power_en>;
+		pinctrl-names = "default";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-name = "hdd_a_power";
+		startup-delay-us = <2000000>;
+	};
+
+	hdd_b_power: hdd-b-power {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio1 RK_PA1 GPIO_ACTIVE_HIGH>;
+		pinctrl-0 = <&hdd_b_power_en>;
+		pinctrl-names = "default";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-name = "hdd_b_power";
+		startup-delay-us = <2000000>;
+	};
+
 	pcie_power: pcie-power {
 		compatible = "regulator-fixed";
 		enable-active-high;
@@ -101,6 +125,18 @@
 		vin-supply = <&vcc5v0_perdev>;
 	};
 
+	usblan_power: usblan-power {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio1 RK_PC7 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&usb_lan_en>;
+		regulator-name = "usblan_power";
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&vcc5v0_usb>;
+	};
+
 	vcc1v8_sys_s0: vcc1v8-sys-s0 {
 		compatible = "regulator-fixed";
 		regulator-name = "vcc1v8_sys_s0";
@@ -276,6 +312,7 @@
 		clock-output-names = "xin32k", "rk808-clkout2";
 		pinctrl-names = "default";
 		pinctrl-0 = <&pmic_int_l>;
+		rockchip,system-power-controller;
 		vcc1-supply = <&vcc5v0_sys>;
 		vcc2-supply = <&vcc5v0_sys>;
 		vcc3-supply = <&vcc5v0_sys>;
@@ -389,7 +426,10 @@
 };
 
 &pcie0 {
+	ep-gpios = <&gpio2 RK_PD4 GPIO_ACTIVE_HIGH>;
+	max-link-speed = <2>;
 	num-lanes = <2>;
+	pinctrl-names = "default";
 	status = "okay";
 
 	vpcie12v-supply = <&vcc12v_dcin>;
@@ -429,9 +469,21 @@
 	};
 
 	power {
+		hdd_a_power_en: hdd-a-power-en {
+			rockchip,pins = <1 RK_PA0 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		hdd_b_power_en: hdd-b-power-en {
+			rockchip,pins = <1 RK_PA1 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
 		vcc5v0_usb_en: vcc5v0-usb-en {
 			rockchip,pins = <1 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>;
 		};
+
+		usb_lan_en: usb-lan-en {
+			rockchip,pins = <1 RK_PC7 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
 	};
 
 	vcc3v0-sd {
@@ -530,5 +582,41 @@
 	usb@fe900000 {
 		dr_mode = "host";
 		status = "okay";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		hub@1 {
+			compatible = "usb2109,0815";
+			reg = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@1 {
+				reg = <1>;
+				#trigger-source-cells = <0>;
+			};
+
+			port@2 {
+				reg = <2>;
+				#trigger-source-cells = <0>;
+			};
+
+			port@3 {
+				reg = <3>;
+				#trigger-source-cells = <0>;
+			};
+
+			device@4 {
+				compatible = "usbbda,8156";
+				reg = <4>;
+				#address-cells = <2>;
+				#size-cells = <0>;
+
+				interface@0 {	/* interface 0 of configuration 1 */
+					compatible = "usbbda,8156.config1.0";
+					reg = <0 1>;
+				};
+			};
+		};
 	};
 };
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-leez-p710.dts b/arch/arm64/boot/dts/rockchip/rk3399-leez-p710.dts
index 7c93f840bc64..a21ac319f809 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-leez-p710.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3399-leez-p710.dts
@@ -5,6 +5,7 @@
 
 /dts-v1/;
 #include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/pwm/pwm.h>
 #include "rk3399.dtsi"
 #include "rk3399-opp.dtsi"
@@ -55,7 +56,7 @@
 		regulator-boot-on;
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
-		vim-supply = <&vcc3v3_sys>;
+		vin-supply = <&vcc3v3_sys>;
 	};
 
 	vcc3v3_sys: vcc3v3-sys {
@@ -102,12 +103,12 @@
 	vdd_log: vdd-log {
 		compatible = "pwm-regulator";
 		pwms = <&pwm2 0 25000 1>;
+		pwm-supply = <&vcc5v0_sys>;
 		regulator-name = "vdd_log";
 		regulator-always-on;
 		regulator-boot-on;
 		regulator-min-microvolt = <800000>;
 		regulator-max-microvolt = <1400000>;
-		vin-supply = <&vcc5v0_sys>;
 	};
 };
 
@@ -509,7 +510,7 @@
 		compatible = "brcm,bcm4329-fmac";
 		reg = <1>;
 		interrupt-parent = <&gpio0>;
-		interrupts = <RK_PA3 GPIO_ACTIVE_HIGH>;
+		interrupts = <RK_PA3 IRQ_TYPE_LEVEL_HIGH>;
 		interrupt-names = "host-wake";
 		pinctrl-names = "default";
 		pinctrl-0 = <&wifi_host_wake_l>;
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-nanopi-r4s-enterprise.dts b/arch/arm64/boot/dts/rockchip/rk3399-nanopi-r4s-enterprise.dts
new file mode 100644
index 000000000000..a23d11ca0eb6
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3399-nanopi-r4s-enterprise.dts
@@ -0,0 +1,29 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+/dts-v1/;
+#include "rk3399-nanopi-r4s.dts"
+
+/ {
+	model = "FriendlyElec NanoPi R4S Enterprise Edition";
+	compatible = "friendlyarm,nanopi-r4s-enterprise", "rockchip,rk3399";
+};
+
+&gmac {
+	nvmem-cells = <&mac_address>;
+	nvmem-cell-names = "mac-address";
+};
+
+&i2c2 {
+	eeprom@51 {
+		compatible = "microchip,24c02", "atmel,24c02";
+		reg = <0x51>;
+		pagesize = <16>;
+		size = <256>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		mac_address: mac-address@fa {
+			reg = <0xfa 0x06>;
+		};
+	};
+};
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-nanopi-r4s.dts b/arch/arm64/boot/dts/rockchip/rk3399-nanopi-r4s.dts
index cef4d18b599d..fe5b52610010 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-nanopi-r4s.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3399-nanopi-r4s.dts
@@ -46,9 +46,9 @@
 	gpio-keys {
 		pinctrl-0 = <&reset_button_pin>;
 
-		/delete-node/ power;
+		/delete-node/ key-power;
 
-		reset {
+		key-reset {
 			debounce-interval = <50>;
 			gpios = <&gpio1 RK_PC6 GPIO_ACTIVE_LOW>;
 			label = "reset";
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-nanopi4.dtsi b/arch/arm64/boot/dts/rockchip/rk3399-nanopi4.dtsi
index 8c0ff6c96e03..278123b4f911 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-nanopi4.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3399-nanopi4.dtsi
@@ -111,7 +111,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&power_key>;
 
-		power {
+		key-power {
 			debounce-interval = <100>;
 			gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_LOW>;
 			label = "GPIO Key Power";
@@ -267,7 +267,7 @@
 		interrupt-parent = <&gpio1>;
 		interrupts = <21 IRQ_TYPE_LEVEL_LOW>;
 		pinctrl-names = "default";
-		pinctrl-0 = <&pmic_int_l>;
+		pinctrl-0 = <&pmic_int_l>, <&ap_pwroff>, <&clk_32k>;
 		rockchip,system-power-controller;
 		wakeup-source;
 
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-op1-opp.dtsi b/arch/arm64/boot/dts/rockchip/rk3399-op1-opp.dtsi
index 2180e0f75003..6e29e74f6fc6 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-op1-opp.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3399-op1-opp.dtsi
@@ -110,6 +110,27 @@
 			opp-microvolt = <1075000>;
 		};
 	};
+
+	dmc_opp_table: dmc_opp_table {
+		compatible = "operating-points-v2";
+
+		opp00 {
+			opp-hz = /bits/ 64 <400000000>;
+			opp-microvolt = <900000>;
+		};
+		opp01 {
+			opp-hz = /bits/ 64 <666000000>;
+			opp-microvolt = <900000>;
+		};
+		opp02 {
+			opp-hz = /bits/ 64 <800000000>;
+			opp-microvolt = <900000>;
+		};
+		opp03 {
+			opp-hz = /bits/ 64 <928000000>;
+			opp-microvolt = <925000>;
+		};
+	};
 };
 
 &cpu_l0 {
@@ -136,6 +157,10 @@
 	operating-points-v2 = <&cluster1_opp>;
 };
 
+&dmc {
+	operating-points-v2 = <&dmc_opp_table>;
+};
+
 &gpu {
 	operating-points-v2 = <&gpu_opp_table>;
 };
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-orangepi.dts b/arch/arm64/boot/dts/rockchip/rk3399-orangepi.dts
index 04b54abea3cc..9e2e246e0bab 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-orangepi.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3399-orangepi.dts
@@ -7,6 +7,7 @@
 
 #include "dt-bindings/pwm/pwm.h"
 #include "dt-bindings/input/input.h"
+#include <dt-bindings/interrupt-controller/irq.h>
 #include "dt-bindings/usb/pd.h"
 #include "rk3399.dtsi"
 #include "rk3399-opp.dtsi"
@@ -77,7 +78,7 @@
 		compatible = "gpio-keys";
 		autorepeat;
 
-		power {
+		key-power {
 			debounce-interval = <100>;
 			gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_LOW>;
 			label = "GPIO Power";
@@ -166,12 +167,12 @@
 	vdd_log: vdd-log {
 		compatible = "pwm-regulator";
 		pwms = <&pwm2 0 25000 1>;
+		pwm-supply = <&vcc_sys>;
 		regulator-name = "vdd_log";
 		regulator-always-on;
 		regulator-boot-on;
 		regulator-min-microvolt = <800000>;
 		regulator-max-microvolt = <1400000>;
-		vin-supply = <&vcc_sys>;
 	};
 };
 
@@ -735,7 +736,7 @@
 		reg = <1>;
 		compatible = "brcm,bcm4329-fmac";
 		interrupt-parent = <&gpio0>;
-		interrupts = <RK_PA3 GPIO_ACTIVE_HIGH>;
+		interrupts = <RK_PA3 IRQ_TYPE_LEVEL_HIGH>;
 		interrupt-names = "host-wake";
 		pinctrl-names = "default";
 		pinctrl-0 = <&wifi_host_wake_l>;
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-pinebook-pro.dts b/arch/arm64/boot/dts/rockchip/rk3399-pinebook-pro.dts
index c2f021a1a18f..194e48c755f6 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-pinebook-pro.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3399-pinebook-pro.dts
@@ -76,7 +76,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&lidbtn_pin>;
 
-		lid {
+		switch-lid {
 			debounce-interval = <20>;
 			gpios = <&gpio1 RK_PA1 GPIO_ACTIVE_LOW>;
 			label = "Lid";
@@ -92,7 +92,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pwrbtn_pin>;
 
-		power {
+		key-power {
 			debounce-interval = <20>;
 			gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_LOW>;
 			label = "Power";
@@ -243,12 +243,12 @@
 	vdd_log: vdd-log {
 		compatible = "pwm-regulator";
 		pwms = <&pwm2 0 25000 1>;
+		pwm-supply = <&vcc_sysin>;
 		regulator-name = "vdd_log";
 		regulator-always-on;
 		regulator-boot-on;
 		regulator-min-microvolt = <800000>;
 		regulator-max-microvolt = <1400000>;
-		vin-supply = <&vcc_sysin>;
 
 		regulator-state-mem {
 			regulator-on-in-suspend;
@@ -472,8 +472,6 @@
 		vcc10-supply = <&vcc_sysin>;
 		vcc11-supply = <&vcc_sysin>;
 		vcc12-supply = <&vcc3v3_sys>;
-		vcc13-supply = <&vcc_sysin>;
-		vcc14-supply = <&vcc_sysin>;
 
 		regulators {
 			/* rk3399 center logic supply */
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-pinephone-pro.dts b/arch/arm64/boot/dts/rockchip/rk3399-pinephone-pro.dts
new file mode 100644
index 000000000000..2e058c315025
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3399-pinephone-pro.dts
@@ -0,0 +1,398 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2020 Martijn Braam <martijn@brixit.nl>
+ * Copyright (c) 2021 Kamil Trzciński <ayufan@ayufan.eu>
+ */
+
+/*
+ * PinePhone Pro datasheet:
+ * https://files.pine64.org/doc/PinePhonePro/PinephonePro-Schematic-V1.0-20211127.pdf
+ */
+
+/dts-v1/;
+#include <dt-bindings/input/linux-event-codes.h>
+#include "rk3399.dtsi"
+#include "rk3399-opp.dtsi"
+
+/ {
+	model = "Pine64 PinePhonePro";
+	compatible = "pine64,pinephone-pro", "rockchip,rk3399";
+	chassis-type = "handset";
+
+	aliases {
+		mmc0 = &sdio0;
+		mmc1 = &sdmmc;
+		mmc2 = &sdhci;
+	};
+
+	chosen {
+		stdout-path = "serial2:115200n8";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pwrbtn_pin>;
+
+		key-power {
+			debounce-interval = <20>;
+			gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_LOW>;
+			label = "Power";
+			linux,code = <KEY_POWER>;
+			wakeup-source;
+		};
+	};
+
+	vcc_sys: vcc-sys-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_sys";
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vcc3v3_sys: vcc3v3-sys-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3_sys";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc_sys>;
+	};
+
+	vcca1v8_s3: vcc1v8-s3-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcca1v8_s3";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vcc3v3_sys>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vcc1v8_codec: vcc1v8-codec-regulator {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio3 RK_PA4 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vcc1v8_codec_en>;
+		regulator-name = "vcc1v8_codec";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vcc3v3_sys>;
+	};
+};
+
+&cpu_l0 {
+	cpu-supply = <&vdd_cpu_l>;
+};
+
+&cpu_l1 {
+	cpu-supply = <&vdd_cpu_l>;
+};
+
+&cpu_l2 {
+	cpu-supply = <&vdd_cpu_l>;
+};
+
+&cpu_l3 {
+	cpu-supply = <&vdd_cpu_l>;
+};
+
+&cpu_b0 {
+	cpu-supply = <&vdd_cpu_b>;
+};
+
+&cpu_b1 {
+	cpu-supply = <&vdd_cpu_b>;
+};
+
+&emmc_phy {
+	status = "okay";
+};
+
+&i2c0 {
+	clock-frequency = <400000>;
+	i2c-scl-rising-time-ns = <168>;
+	i2c-scl-falling-time-ns = <4>;
+	status = "okay";
+
+	rk818: pmic@1c {
+		compatible = "rockchip,rk818";
+		reg = <0x1c>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <RK_PC5 IRQ_TYPE_LEVEL_LOW>;
+		#clock-cells = <1>;
+		clock-output-names = "xin32k", "rk808-clkout2";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_int_l>;
+		rockchip,system-power-controller;
+		wakeup-source;
+
+		vcc1-supply = <&vcc_sys>;
+		vcc2-supply = <&vcc_sys>;
+		vcc3-supply = <&vcc_sys>;
+		vcc4-supply = <&vcc_sys>;
+		vcc6-supply = <&vcc_sys>;
+		vcc7-supply = <&vcc3v3_sys>;
+		vcc8-supply = <&vcc_sys>;
+		vcc9-supply = <&vcc3v3_sys>;
+
+		regulators {
+			vdd_cpu_l: DCDC_REG1 {
+				regulator-name = "vdd_cpu_l";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <875000>;
+				regulator-max-microvolt = <975000>;
+				regulator-ramp-delay = <6001>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdd_center: DCDC_REG2 {
+				regulator-name = "vdd_center";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1000000>;
+				regulator-ramp-delay = <6001>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_ddr: DCDC_REG3 {
+				regulator-name = "vcc_ddr";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vcc_1v8: DCDC_REG4 {
+				regulator-name = "vcc_1v8";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vcca3v0_codec: LDO_REG1 {
+				regulator-name = "vcca3v0_codec";
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3000000>;
+			};
+
+			vcc3v0_touch: LDO_REG2 {
+				regulator-name = "vcc3v0_touch";
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3000000>;
+			};
+
+			vcca1v8_codec: LDO_REG3 {
+				regulator-name = "vcca1v8_codec";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+
+			rk818_pwr_on: LDO_REG4 {
+				regulator-name = "rk818_pwr_on";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vcc_3v0: LDO_REG5 {
+				regulator-name = "vcc_3v0";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vcc_1v5: LDO_REG6 {
+				regulator-name = "vcc_1v5";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1500000>;
+				regulator-max-microvolt = <1500000>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vcc1v8_dvp: LDO_REG7 {
+				regulator-name = "vcc1v8_dvp";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+			};
+
+			vcc3v3_s3: LDO_REG8 {
+				regulator-name = "vcc3v3_s3";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vccio_sd: LDO_REG9 {
+				regulator-name = "vccio_sd";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+			};
+
+			vcc3v3_s0: SWITCH_REG {
+				regulator-name = "vcc3v3_s0";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+		};
+	};
+
+	vdd_cpu_b: regulator@40 {
+		compatible = "silergy,syr827";
+		reg = <0x40>;
+		fcs,suspend-voltage-selector = <1>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vsel1_pin>;
+		regulator-name = "vdd_cpu_b";
+		regulator-min-microvolt = <875000>;
+		regulator-max-microvolt = <1150000>;
+		regulator-ramp-delay = <1000>;
+		regulator-always-on;
+		regulator-boot-on;
+
+		regulator-state-mem {
+			regulator-off-in-suspend;
+		};
+	};
+
+	vdd_gpu: regulator@41 {
+		compatible = "silergy,syr828";
+		reg = <0x41>;
+		fcs,suspend-voltage-selector = <1>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vsel2_pin>;
+		regulator-name = "vdd_gpu";
+		regulator-min-microvolt = <875000>;
+		regulator-max-microvolt = <975000>;
+		regulator-ramp-delay = <1000>;
+		regulator-always-on;
+		regulator-boot-on;
+
+		regulator-state-mem {
+			regulator-off-in-suspend;
+		};
+	};
+};
+
+&cluster0_opp {
+	opp04 {
+		status = "disabled";
+	};
+
+	opp05 {
+		status = "disabled";
+	};
+};
+
+&cluster1_opp {
+	opp06 {
+		opp-hz = /bits/ 64 <1500000000>;
+		opp-microvolt = <1100000 1100000 1150000>;
+	};
+
+	opp07 {
+		status = "disabled";
+	};
+};
+
+&io_domains {
+	bt656-supply = <&vcc1v8_dvp>;
+	audio-supply = <&vcca1v8_codec>;
+	sdmmc-supply = <&vccio_sd>;
+	gpio1830-supply = <&vcc_3v0>;
+	status = "okay";
+};
+
+&pmu_io_domains {
+	pmu1830-supply = <&vcc_1v8>;
+	status = "okay";
+};
+
+&pinctrl {
+	buttons {
+		pwrbtn_pin: pwrbtn-pin {
+			rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	pmic {
+		pmic_int_l: pmic-int-l {
+			rockchip,pins = <1 RK_PC5 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+
+		vsel1_pin: vsel1-pin {
+			rockchip,pins = <1 RK_PC1 RK_FUNC_GPIO &pcfg_pull_down>;
+		};
+
+		vsel2_pin: vsel2-pin {
+			rockchip,pins = <1 RK_PB6 RK_FUNC_GPIO &pcfg_pull_down>;
+		};
+	};
+
+	sound {
+		vcc1v8_codec_en: vcc1v8-codec-en {
+			rockchip,pins = <3 RK_PA4 RK_FUNC_GPIO &pcfg_pull_down>;
+		};
+	};
+};
+
+&sdmmc {
+	bus-width = <4>;
+	cap-sd-highspeed;
+	cd-gpios = <&gpio0 RK_PA7 GPIO_ACTIVE_LOW>;
+	disable-wp;
+	max-frequency = <150000000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd &sdmmc_bus4>;
+	vmmc-supply = <&vcc3v3_sys>;
+	vqmmc-supply = <&vccio_sd>;
+	status = "okay";
+};
+
+&sdhci {
+	bus-width = <8>;
+	mmc-hs200-1_8v;
+	non-removable;
+	status = "okay";
+};
+
+&tsadc {
+	rockchip,hw-tshut-mode = <1>;
+	rockchip,hw-tshut-polarity = <1>;
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-puma-haikou.dts b/arch/arm64/boot/dts/rockchip/rk3399-puma-haikou.dts
index 292bb7e80cf3..04c752f49be9 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-puma-haikou.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3399-puma-haikou.dts
@@ -49,7 +49,7 @@
 	sgtl5000_clk: sgtl5000-oscillator  {
 			compatible = "fixed-clock";
 			#clock-cells = <0>;
-			clock-frequency  = <24576000>;
+			clock-frequency = <24576000>;
 	};
 
 	dc_12v: dc-12v {
@@ -232,6 +232,7 @@
 
 &usbdrd_dwc3_0 {
 	dr_mode = "otg";
+	extcon = <&extcon_usb3>;
 	status = "okay";
 };
 
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-puma.dtsi b/arch/arm64/boot/dts/rockchip/rk3399-puma.dtsi
index fb67db4619ea..aa3e21bd6c8f 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-puma.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3399-puma.dtsi
@@ -25,6 +25,13 @@
 		};
 	};
 
+	extcon_usb3: extcon-usb3 {
+		compatible = "linux,extcon-usb-gpio";
+		id-gpio = <&gpio1 RK_PC2 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&usb3_id>;
+	};
+
 	clkin_gmac: external-gmac-clock {
 		compatible = "fixed-clock";
 		clock-frequency = <125000000>;
@@ -55,7 +62,6 @@
 	vcc5v0_host: vcc5v0-host-regulator {
 		compatible = "regulator-fixed";
 		gpio = <&gpio4 RK_PA3 GPIO_ACTIVE_LOW>;
-		enable-active-low;
 		pinctrl-names = "default";
 		pinctrl-0 = <&vcc5v0_host_en>;
 		regulator-name = "vcc5v0_host";
@@ -71,6 +77,17 @@
 		regulator-min-microvolt = <5000000>;
 		regulator-max-microvolt = <5000000>;
 	};
+
+	vdd_log: vdd-log {
+		compatible = "pwm-regulator";
+		pwms = <&pwm2 0 25000 1>;
+		pwm-supply = <&vcc5v0_sys>;
+		regulator-name = "vdd_log";
+		regulator-min-microvolt = <800000>;
+		regulator-max-microvolt = <1400000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
 };
 
 &cpu_b0 {
@@ -422,9 +439,22 @@
 			  <4 RK_PA3 RK_FUNC_GPIO &pcfg_pull_none>;
 		};
 	};
+
+	usb3 {
+		usb3_id: usb3-id {
+			rockchip,pins =
+			  <1 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
 };
 
 &sdhci {
+	/*
+	 * Signal integrity isn't great at 200MHz but 100MHz has proven stable
+	 * enough.
+	 */
+	max-frequency = <100000000>;
+
 	bus-width = <8>;
 	mmc-hs400-1_8v;
 	mmc-hs400-enhanced-strobe;
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-roc-pc.dtsi b/arch/arm64/boot/dts/rockchip/rk3399-roc-pc.dtsi
index d1aaf8e83391..2f4b1b2e3ac7 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-roc-pc.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3399-roc-pc.dtsi
@@ -54,7 +54,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pwr_key_l>;
 
-		power {
+		key-power {
 			debounce-interval = <100>;
 			gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_LOW>;
 			label = "GPIO Key Power";
@@ -271,6 +271,8 @@
 };
 
 &hdmi {
+	avdd-0v9-supply = <&vcca0v9_hdmi>;
+	avdd-1v8-supply = <&vcca1v8_hdmi>;
 	ddc-i2c-bus = <&i2c3>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&hdmi_cec>;
@@ -310,8 +312,6 @@
 		vcc10-supply = <&vcc3v3_sys>;
 		vcc11-supply = <&vcc3v3_sys>;
 		vcc12-supply = <&vcc3v3_sys>;
-		vcc13-supply = <&vcc3v3_sys>;
-		vcc14-supply = <&vcc3v3_sys>;
 		vddio-supply = <&vcc_3v0>;
 
 		regulators {
@@ -371,8 +371,8 @@
 				};
 			};
 
-			vcc1v8_hdmi: LDO_REG2 {
-				regulator-name = "vcc1v8_hdmi";
+			vcca1v8_hdmi: LDO_REG2 {
+				regulator-name = "vcca1v8_hdmi";
 				regulator-always-on;
 				regulator-boot-on;
 				regulator-min-microvolt = <1800000>;
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-rock-4c-plus.dts b/arch/arm64/boot/dts/rockchip/rk3399-rock-4c-plus.dts
new file mode 100644
index 000000000000..f9884902f874
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3399-rock-4c-plus.dts
@@ -0,0 +1,703 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2019 Fuzhou Rockchip Electronics Co., Ltd
+ * Copyright (c) 2019 Radxa Limited
+ * Copyright (c) 2022 Amarula Solutions(India)
+ */
+
+/dts-v1/;
+#include <dt-bindings/leds/common.h>
+#include "rk3399.dtsi"
+#include "rk3399-t-opp.dtsi"
+
+/ {
+	model = "Radxa ROCK 4C+";
+	compatible = "radxa,rock-4c-plus", "rockchip,rk3399";
+
+	aliases {
+		mmc0 = &sdmmc;
+		mmc1 = &sdhci;
+	};
+
+	chosen {
+		stdout-path = "serial2:1500000n8";
+	};
+
+	clkin_gmac: external-gmac-clock {
+		compatible = "fixed-clock";
+		clock-frequency = <125000000>;
+		clock-output-names = "clkin_gmac";
+		#clock-cells = <0>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&user_led1 &user_led2>;
+
+		/* USER_LED1 */
+		led-0 {
+			function = LED_FUNCTION_POWER;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&gpio3 RK_PD4 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "default-on";
+		};
+
+		/* USER_LED2 */
+		led-1 {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_BLUE>;
+			gpios = <&gpio3 RK_PD5 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	sdio_pwrseq: sdio-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		clocks = <&rk809 1>;
+		clock-names = "ext_clock";
+		pinctrl-names = "default";
+		pinctrl-0 = <&wifi_enable_h>;
+		reset-gpios = <&gpio0 RK_PB2 GPIO_ACTIVE_LOW>;
+	};
+
+	vcc_3v3: vcc-3v3-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_3v3";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc3v3_sys>;
+	};
+
+	vcc3v3_phy1: vcc3v3-phy1-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3_phy1";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc_3v3>;
+	};
+
+	vcc5v0_host1: vcc5v0-host-regulator {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio3 RK_PD6 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vcc5v0_host_en>;
+		regulator-name = "vcc5v0_host1";
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&vcc5v0_host0_s0>;
+	};
+
+	vcc5v0_sys: vcc5v0-sys-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc5v0_sys";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	vcc5v0_typec: vcc5v0-typec-regulator {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio1 RK_PA3 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vcc5v0_typec0_en>;
+		regulator-name = "vcc5v0_typec";
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&vcc5v0_sys>;
+	};
+
+	vdd_log: vdd-log-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_log";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <950000>;
+		regulator-max-microvolt = <950000>;
+		vin-supply = <&vcc5v0_sys>;
+	};
+};
+
+&cpu_l0 {
+	cpu-supply = <&vdd_cpu_l>;
+};
+
+&cpu_l1 {
+	cpu-supply = <&vdd_cpu_l>;
+};
+
+&cpu_l2 {
+	cpu-supply = <&vdd_cpu_l>;
+};
+
+&cpu_l3 {
+	cpu-supply = <&vdd_cpu_l>;
+};
+
+&cpu_b0 {
+	cpu-supply = <&vdd_cpu_b>;
+};
+
+&cpu_b1 {
+	cpu-supply = <&vdd_cpu_b>;
+};
+
+&emmc_phy {
+	status = "okay";
+};
+
+&gmac {
+	assigned-clocks = <&cru SCLK_RMII_SRC>;
+	assigned-clock-parents = <&clkin_gmac>;
+	clock_in_out = "input";
+	phy-supply = <&vcc3v3_phy1>;
+	phy-mode = "rgmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&rgmii_pins>;
+	snps,reset-gpio = <&gpio3 RK_PB7 GPIO_ACTIVE_LOW>;
+	snps,reset-active-low;
+	snps,reset-delays-us = <0 10000 50000>;
+	tx_delay = <0x2a>;
+	rx_delay = <0x21>;
+	status = "okay";
+};
+
+&gpu {
+	mali-supply = <&vdd_gpu>;
+	status = "okay";
+};
+
+&hdmi {
+	avdd-0v9-supply = <&vcc_0v9_s0>;
+	avdd-1v8-supply = <&vcc_1v8_s0>;
+	ddc-i2c-bus = <&i2c3>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&hdmi_cec>;
+	status = "okay";
+};
+
+&hdmi_sound {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+	i2c-scl-falling-time-ns = <30>;
+	i2c-scl-rising-time-ns = <180>;
+	clock-frequency = <400000>;
+
+	rk809: pmic@20 {
+		compatible = "rockchip,rk809";
+		reg = <0x20>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <RK_PC5 IRQ_TYPE_LEVEL_LOW>;
+		#clock-cells = <1>;
+		clock-output-names = "rk808-clkout1", "rk808-clkout2";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_int_l>;
+		rockchip,system-power-controller;
+		wakeup-source;
+
+		vcc1-supply = <&vcc5v0_sys>;
+		vcc2-supply = <&vcc5v0_sys>;
+		vcc3-supply = <&vcc5v0_sys>;
+		vcc4-supply = <&vcc5v0_sys>;
+		vcc5-supply = <&vcc_buck5_s3>;
+		vcc6-supply = <&vcc_buck5_s3>;
+		vcc7-supply = <&vcc5v0_sys>;
+		vcc8-supply = <&vcc3v3_sys>;
+		vcc9-supply = <&vcc5v0_sys>;
+
+		regulators {
+			vdd_center: DCDC_REG1 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <750000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-initial-mode = <0x2>;
+				regulator-name = "vdd_center";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+					regulator-suspend-microvolt = <900000>;
+				};
+			};
+
+			vdd_cpu_l: DCDC_REG2 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <750000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-ramp-delay = <6001>;
+				regulator-initial-mode = <0x2>;
+				regulator-name = "vdd_cpu_l";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_ddr: DCDC_REG3 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-name = "vcc_ddr";
+				regulator-initial-mode = <0x2>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vcc3v3_sys: DCDC_REG4 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-initial-mode = <0x2>;
+				regulator-name = "vcc3v3_sys";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+				};
+			};
+
+			vcc_buck5_s3: DCDC_REG5 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc_buck5_s3";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+				};
+			};
+
+			vcc_0v9_s3: LDO_REG1 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <900000>;
+				regulator-name = "vcc_0v9_s3";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_1v8_s3: LDO_REG2 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcc_1v8_s3";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vcc_0v9_s0: LDO_REG3 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <900000>;
+				regulator-name = "vcc_0v9_s0";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <900000>;
+				};
+			};
+
+			vcc_1v8_s0: LDO_REG4 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcc_1v8_s0";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_mipi: LDO_REG5 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-name = "vcc_mipi";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_1v5_s0: LDO_REG6 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1500000>;
+				regulator-max-microvolt = <1500000>;
+				regulator-name = "vcc_1v5_s0";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_3v0_s0: LDO_REG7 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-name = "vcc_3v0_s0";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_sdio_s0: LDO_REG8 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc_sdio_s0";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_cam: LDO_REG9 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc_cam";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc5v0_host0_s0: SWITCH_REG1 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-name = "vcc5v0_host0_s0";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			lcd_3v3: SWITCH_REG2 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-name = "lcd_3v3";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+		};
+	};
+
+	vdd_cpu_b: regulator@40 {
+		compatible = "silergy,syr827";
+		reg = <0x40>;
+		fcs,suspend-voltage-selector = <1>;
+		regulator-compatible = "fan53555-reg";
+		pinctrl-0 = <&vsel1_gpio>;
+		vsel-gpios = <&gpio1 RK_PC1 GPIO_ACTIVE_HIGH>;
+		regulator-name = "vdd_cpu_b";
+		regulator-min-microvolt = <712500>;
+		regulator-max-microvolt = <1500000>;
+		regulator-ramp-delay = <1000>;
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&vcc5v0_sys>;
+		regulator-state-mem {
+			regulator-off-in-suspend;
+		};
+	};
+
+	vdd_gpu: regulator@41 {
+		compatible = "silergy,syr828";
+		reg = <0x41>;
+		fcs,suspend-voltage-selector = <1>;
+		regulator-compatible = "fan53555-reg";
+		pinctrl-0 = <&vsel2_gpio>;
+		vsel-gpios = <&gpio1 RK_PB6 GPIO_ACTIVE_HIGH>;
+		regulator-name = "vdd_gpu";
+		regulator-min-microvolt = <712500>;
+		regulator-max-microvolt = <1500000>;
+		regulator-ramp-delay = <1000>;
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&vcc5v0_sys>;
+		regulator-initial-mode = <1>; /* 1:force PWM 2:auto */
+		regulator-state-mem {
+			regulator-off-in-suspend;
+		};
+	};
+};
+
+&i2c3 {
+	i2c-scl-rising-time-ns = <450>;
+	i2c-scl-falling-time-ns = <15>;
+	status = "okay";
+};
+
+&i2s2 {
+	status = "okay";
+};
+
+&io_domains {
+	audio-supply = <&vcc_1v8_s0>;
+	bt656-supply = <&vcc_3v0_s0>;
+	gpio1830-supply = <&vcc_3v0_s0>;
+	sdmmc-supply = <&vcc_sdio_s0>;
+	status = "okay";
+};
+
+&pinctrl {
+	bt {
+		bt_enable_h: bt-enable-h {
+			rockchip,pins = <0 RK_PB1 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		bt_host_wake_l: bt-host-wake-l {
+			rockchip,pins = <0 RK_PA4 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		bt_wake_l: bt-wake-l {
+			rockchip,pins = <2 RK_PD3 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	leds {
+		user_led1: user-led1 {
+			rockchip,pins = <3 RK_PD4 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		user_led2: user-led2 {
+			rockchip,pins = <3 RK_PD5 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	pmic {
+		pmic_int_l: pmic-int-l {
+			rockchip,pins = <1 RK_PC5 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+
+		vsel1_gpio: vsel1-gpio {
+			rockchip,pins = <1 RK_PC1 RK_FUNC_GPIO &pcfg_pull_down>;
+		};
+
+		vsel2_gpio: vsel2-gpio {
+			rockchip,pins = <1 RK_PB6 RK_FUNC_GPIO &pcfg_pull_down>;
+		};
+	};
+
+	sdmmc {
+		sdmmc_bus4: sdmmc-bus4 {
+			rockchip,pins = <4 8 1 &pcfg_pull_up_8ma>,
+					<4 9 1 &pcfg_pull_up_8ma>,
+					<4 10 1 &pcfg_pull_up_8ma>,
+					<4 11 1 &pcfg_pull_up_8ma>;
+		};
+
+		sdmmc_clk: sdmmc-clk {
+			rockchip,pins = <4 12 1 &pcfg_pull_none_18ma>;
+		};
+
+		sdmmc_cmd: sdmmc-cmd {
+			rockchip,pins = <4 13 1 &pcfg_pull_up_8ma>;
+		};
+	};
+
+	usb-typec {
+		vcc5v0_typec0_en: vcc5v0-typec-en {
+			rockchip,pins = <1 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	usb2 {
+		vcc5v0_host_en: vcc5v0-host-en {
+			rockchip,pins = <3 RK_PD6 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	wifi {
+		wifi_enable_h: wifi-enable-h {
+			rockchip,pins = <0 RK_PB2 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		wifi_host_wake_l: wifi-host-wake-l {
+			rockchip,pins = <0 RK_PA3 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+};
+
+&pmu_io_domains {
+	pmu1830-supply = <&vcc_3v0_s0>;
+	status = "okay";
+};
+
+&saradc {
+	status = "okay";
+	vref-supply = <&vcc_1v8_s3>;
+};
+
+&sdhci {
+	max-frequency = <150000000>;
+	bus-width = <8>;
+	mmc-hs400-1_8v;
+	non-removable;
+	mmc-hs400-enhanced-strobe;
+	status = "okay";
+};
+
+&sdio0 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	bus-width = <4>;
+	clock-frequency = <50000000>;
+	cap-sdio-irq;
+	cap-sd-highspeed;
+	keep-power-in-suspend;
+	mmc-pwrseq = <&sdio_pwrseq>;
+	non-removable;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdio0_bus4 &sdio0_cmd &sdio0_clk>;
+	sd-uhs-sdr104;
+	status = "okay";
+
+	brcmf: wifi@1 {
+		compatible = "brcm,bcm4329-fmac";
+		reg = <1>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <RK_PA3 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "host-wake";
+		pinctrl-names = "default";
+		pinctrl-0 = <&wifi_host_wake_l>;
+	};
+};
+
+&sdmmc {
+	bus-width = <4>;
+	cap-mmc-highspeed;
+	cap-sd-highspeed;
+	card-detect-delay = <800>;
+	disable-wp;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_bus4>;
+	cd-gpios = <&gpio0 RK_PA7 GPIO_ACTIVE_LOW>;
+	vqmmc-supply = <&vcc_sdio_s0>;
+	status = "okay";
+};
+
+&tcphy0 {
+	status = "okay";
+};
+
+&tcphy1 {
+	status = "okay";
+};
+
+&u2phy0 {
+	status = "okay";
+
+	u2phy0_otg: otg-port {
+		status = "okay";
+	};
+
+	u2phy0_host: host-port {
+		phy-supply = <&vcc5v0_host1>;
+		status = "okay";
+	};
+};
+
+&u2phy1 {
+	status = "okay";
+
+	u2phy1_otg: otg-port {
+		status = "okay";
+	};
+
+	u2phy1_host: host-port {
+		phy-supply = <&vcc5v0_host1>;
+		status = "okay";
+	};
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_xfer &uart0_cts &uart0_rts>;
+	status = "okay";
+
+	bluetooth {
+		compatible = "brcm,bcm4345c5";
+		clocks = <&rk809 1>;
+		clock-names = "lpo";
+		device-wakeup-gpios = <&gpio2 RK_PD3 GPIO_ACTIVE_HIGH>;
+		host-wakeup-gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_HIGH>;
+		shutdown-gpios = <&gpio0 RK_PB1 GPIO_ACTIVE_HIGH>;
+		max-speed = <1500000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&bt_host_wake_l &bt_wake_l &bt_enable_h>;
+		vbat-supply = <&vcc3v3_sys>;
+		vddio-supply = <&vcc_1v8_s3>;
+	};
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&usb_host0_ehci {
+	status = "okay";
+};
+
+&usb_host0_ohci {
+	status = "okay";
+};
+
+&usb_host1_ehci {
+	status = "okay";
+};
+
+&usb_host1_ohci {
+	status = "okay";
+};
+
+&usbdrd3_0 {
+	extcon = <&u2phy0>;
+	status = "okay";
+};
+
+&usbdrd_dwc3_0 {
+	status = "okay";
+	dr_mode = "host";
+};
+
+&usbdrd3_1 {
+	status = "okay";
+};
+
+&usbdrd_dwc3_1 {
+	status = "okay";
+	dr_mode = "host";
+};
+
+&vopb {
+	status = "okay";
+};
+
+&vopb_mmu {
+	status = "okay";
+};
+
+&vopl {
+	status = "okay";
+};
+
+&vopl_mmu {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-rock-pi-4.dtsi b/arch/arm64/boot/dts/rockchip/rk3399-rock-pi-4.dtsi
index 98136c88fa49..645ced6617a6 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-rock-pi-4.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3399-rock-pi-4.dtsi
@@ -6,6 +6,7 @@
 
 /dts-v1/;
 #include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/leds/common.h>
 #include <dt-bindings/pwm/pwm.h>
 #include "rk3399.dtsi"
 #include "rk3399-opp.dtsi"
@@ -27,6 +28,20 @@
 		#clock-cells = <0>;
 	};
 
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&user_led2>;
+
+		/* USER_LED2 */
+		led-0 {
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_BLUE>;
+			gpios = <&gpio3 RK_PD5 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
 	sdio_pwrseq: sdio-pwrseq {
 		compatible = "mmc-pwrseq-simple";
 		clocks = <&rk808 1>;
@@ -36,7 +51,7 @@
 		reset-gpios = <&gpio0 RK_PB2 GPIO_ACTIVE_LOW>;
 	};
 
-	sound {
+	sound: sound {
 		compatible = "audio-graph-card";
 		label = "Analog";
 		dais = <&i2s0_p0>;
@@ -59,32 +74,33 @@
 		};
 	};
 
-	vcc12v_dcin: dc-12v {
+	vbus_typec: vbus-typec-regulator {
 		compatible = "regulator-fixed";
-		regulator-name = "vcc12v_dcin";
+		enable-active-high;
+		gpio = <&gpio1 RK_PA3 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vcc5v0_typec_en>;
+		regulator-name = "vbus_typec";
 		regulator-always-on;
-		regulator-boot-on;
-		regulator-min-microvolt = <12000000>;
-		regulator-max-microvolt = <12000000>;
+		vin-supply = <&vcc5v0_sys>;
 	};
 
-	vcc5v0_sys: vcc-sys {
+	vcc12v_dcin: dc-12v {
 		compatible = "regulator-fixed";
-		regulator-name = "vcc5v0_sys";
+		regulator-name = "vcc12v_dcin";
 		regulator-always-on;
 		regulator-boot-on;
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-		vin-supply = <&vcc12v_dcin>;
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
 	};
 
-	vcc_0v9: vcc-0v9 {
+	vcc3v3_lan: vcc3v3-lan-regulator {
 		compatible = "regulator-fixed";
-		regulator-name = "vcc_0v9";
+		regulator-name = "vcc3v3_lan";
 		regulator-always-on;
 		regulator-boot-on;
-		regulator-min-microvolt = <900000>;
-		regulator-max-microvolt = <900000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
 		vin-supply = <&vcc3v3_sys>;
 	};
 
@@ -121,35 +137,35 @@
 		vin-supply = <&vcc5v0_sys>;
 	};
 
-	vcc5v0_typec: vcc5v0-typec-regulator {
+	vcc5v0_sys: vcc-sys {
 		compatible = "regulator-fixed";
-		enable-active-high;
-		gpio = <&gpio1 RK_PA3 GPIO_ACTIVE_HIGH>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&vcc5v0_typec_en>;
-		regulator-name = "vcc5v0_typec";
+		regulator-name = "vcc5v0_sys";
 		regulator-always-on;
-		vin-supply = <&vcc5v0_sys>;
+		regulator-boot-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc12v_dcin>;
 	};
 
-	vcc_lan: vcc3v3-phy-regulator {
+	vcc_0v9: vcc-0v9 {
 		compatible = "regulator-fixed";
-		regulator-name = "vcc_lan";
+		regulator-name = "vcc_0v9";
 		regulator-always-on;
 		regulator-boot-on;
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <900000>;
+		regulator-max-microvolt = <900000>;
+		vin-supply = <&vcc3v3_sys>;
 	};
 
 	vdd_log: vdd-log {
 		compatible = "pwm-regulator";
 		pwms = <&pwm2 0 25000 1>;
+		pwm-supply = <&vcc5v0_sys>;
 		regulator-name = "vdd_log";
 		regulator-always-on;
 		regulator-boot-on;
 		regulator-min-microvolt = <800000>;
 		regulator-max-microvolt = <1400000>;
-		vin-supply = <&vcc5v0_sys>;
 	};
 };
 
@@ -185,7 +201,7 @@
 	assigned-clocks = <&cru SCLK_RMII_SRC>;
 	assigned-clock-parents = <&clkin_gmac>;
 	clock_in_out = "input";
-	phy-supply = <&vcc_lan>;
+	phy-supply = <&vcc3v3_lan>;
 	phy-mode = "rgmii";
 	pinctrl-names = "default";
 	pinctrl-0 = <&rgmii_pins>;
@@ -203,6 +219,8 @@
 };
 
 &hdmi {
+	avdd-0v9-supply = <&vcca0v9_hdmi>;
+	avdd-1v8-supply = <&vcca1v8_hdmi>;
 	ddc-i2c-bus = <&i2c3>;
 	pinctrl-names = "default";
 	pinctrl-0 = <&hdmi_cec>;
@@ -290,8 +308,8 @@
 				};
 			};
 
-			vcc1v8_codec: LDO_REG1 {
-				regulator-name = "vcc1v8_codec";
+			vcca1v8_codec: LDO_REG1 {
+				regulator-name = "vcca1v8_codec";
 				regulator-always-on;
 				regulator-boot-on;
 				regulator-min-microvolt = <1800000>;
@@ -301,8 +319,8 @@
 				};
 			};
 
-			vcc1v8_hdmi: LDO_REG2 {
-				regulator-name = "vcc1v8_hdmi";
+			vcca1v8_hdmi: LDO_REG2 {
+				regulator-name = "vcca1v8_hdmi";
 				regulator-always-on;
 				regulator-boot-on;
 				regulator-min-microvolt = <1800000>;
@@ -359,8 +377,8 @@
 				};
 			};
 
-			vcc0v9_hdmi: LDO_REG7 {
-				regulator-name = "vcc0v9_hdmi";
+			vcca0v9_hdmi: LDO_REG7 {
+				regulator-name = "vcca0v9_hdmi";
 				regulator-always-on;
 				regulator-boot-on;
 				regulator-min-microvolt = <900000>;
@@ -499,21 +517,10 @@
 };
 
 &io_domains {
-	status = "okay";
-
+	audio-supply = <&vcca1v8_codec>;
 	bt656-supply = <&vcc_3v0>;
-	audio-supply = <&vcc_3v0>;
-	sdmmc-supply = <&vcc_sdio>;
 	gpio1830-supply = <&vcc_3v0>;
-};
-
-&pmu_io_domains {
-	status = "okay";
-
-	pmu1830-supply = <&vcc_3v0>;
-};
-
-&pcie_phy {
+	sdmmc-supply = <&vcc_sdio>;
 	status = "okay";
 };
 
@@ -528,6 +535,10 @@
 	status = "okay";
 };
 
+&pcie_phy {
+	status = "okay";
+};
+
 &pinctrl {
 	bt {
 		bt_enable_h: bt-enable-h {
@@ -543,26 +554,25 @@
 		};
 	};
 
-	pcie {
-		pcie_pwr_en: pcie-pwr-en {
-			rockchip,pins = <2 RK_PD2 RK_FUNC_GPIO &pcfg_pull_none>;
+	es8316 {
+		hp_detect: hp-detect {
+			rockchip,pins = <1 RK_PA0 RK_FUNC_GPIO &pcfg_pull_none>;
 		};
-	};
 
-	sdio0 {
-		sdio0_bus4: sdio0-bus4 {
-			rockchip,pins = <2 RK_PC4 1 &pcfg_pull_up_20ma>,
-					<2 RK_PC5 1 &pcfg_pull_up_20ma>,
-					<2 RK_PC6 1 &pcfg_pull_up_20ma>,
-					<2 RK_PC7 1 &pcfg_pull_up_20ma>;
+		hp_int: hp-int {
+			rockchip,pins = <1 RK_PA1 RK_FUNC_GPIO &pcfg_pull_up>;
 		};
+	};
 
-		sdio0_cmd: sdio0-cmd {
-			rockchip,pins = <2 RK_PD0 1 &pcfg_pull_up_20ma>;
+	leds {
+		user_led2: user-led2 {
+			rockchip,pins = <3 RK_PD5 RK_FUNC_GPIO &pcfg_pull_none>;
 		};
+	};
 
-		sdio0_clk: sdio0-clk {
-			rockchip,pins = <2 RK_PD1 1 &pcfg_pull_none_20ma>;
+	pcie {
+		pcie_pwr_en: pcie-pwr-en {
+			rockchip,pins = <2 RK_PD2 RK_FUNC_GPIO &pcfg_pull_none>;
 		};
 	};
 
@@ -580,6 +590,23 @@
 		};
 	};
 
+	sdio0 {
+		sdio0_bus4: sdio0-bus4 {
+			rockchip,pins = <2 RK_PC4 1 &pcfg_pull_up_20ma>,
+					<2 RK_PC5 1 &pcfg_pull_up_20ma>,
+					<2 RK_PC6 1 &pcfg_pull_up_20ma>,
+					<2 RK_PC7 1 &pcfg_pull_up_20ma>;
+		};
+
+		sdio0_cmd: sdio0-cmd {
+			rockchip,pins = <2 RK_PD0 1 &pcfg_pull_up_20ma>;
+		};
+
+		sdio0_clk: sdio0-clk {
+			rockchip,pins = <2 RK_PD1 1 &pcfg_pull_none_20ma>;
+		};
+	};
+
 	usb-typec {
 		vcc5v0_typec_en: vcc5v0-typec-en {
 			rockchip,pins = <1 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>;
@@ -603,6 +630,11 @@
 	};
 };
 
+&pmu_io_domains {
+	pmu1830-supply = <&vcc_3v0>;
+	status = "okay";
+};
+
 &pwm2 {
 	status = "okay";
 };
@@ -613,6 +645,14 @@
 	vref-supply = <&vcc_1v8>;
 };
 
+&sdhci {
+	bus-width = <8>;
+	mmc-hs400-1_8v;
+	mmc-hs400-enhanced-strobe;
+	non-removable;
+	status = "okay";
+};
+
 &sdio0 {
 	#address-cells = <1>;
 	#size-cells = <0>;
@@ -640,14 +680,6 @@
 	status = "okay";
 };
 
-&sdhci {
-	bus-width = <8>;
-	mmc-hs400-1_8v;
-	mmc-hs400-enhanced-strobe;
-	non-removable;
-	status = "okay";
-};
-
 &spdif {
 
 	spdif_p0: port {
@@ -729,13 +761,13 @@
 	status = "okay";
 };
 
-&usbdrd_dwc3_0 {
+&usbdrd3_1 {
 	status = "okay";
-	dr_mode = "host";
 };
 
-&usbdrd3_1 {
+&usbdrd_dwc3_0 {
 	status = "okay";
+	dr_mode = "host";
 };
 
 &usbdrd_dwc3_1 {
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-rock-pi-4a-plus.dts b/arch/arm64/boot/dts/rockchip/rk3399-rock-pi-4a-plus.dts
index 281a04b2f5e9..f5a68d8d072d 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-rock-pi-4a-plus.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3399-rock-pi-4a-plus.dts
@@ -12,3 +12,14 @@
 	model = "Radxa ROCK Pi 4A+";
 	compatible = "radxa,rockpi4a-plus", "radxa,rockpi4", "rockchip,rk3399";
 };
+
+&es8316 {
+	pinctrl-0 = <&hp_detect &hp_int>;
+	pinctrl-names = "default";
+	interrupt-parent = <&gpio1>;
+	interrupts = <RK_PA1 IRQ_TYPE_LEVEL_HIGH>;
+};
+
+&sound {
+	hp-det-gpio = <&gpio1 RK_PA0 GPIO_ACTIVE_HIGH>;
+};
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-rock-pi-4b-plus.dts b/arch/arm64/boot/dts/rockchip/rk3399-rock-pi-4b-plus.dts
index dfad13d2ab24..cec3b7b1b947 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-rock-pi-4b-plus.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3399-rock-pi-4b-plus.dts
@@ -17,6 +17,13 @@
 	};
 };
 
+&es8316 {
+	pinctrl-0 = <&hp_detect &hp_int>;
+	pinctrl-names = "default";
+	interrupt-parent = <&gpio1>;
+	interrupts = <RK_PA1 IRQ_TYPE_LEVEL_HIGH>;
+};
+
 &sdio0 {
 	status = "okay";
 
@@ -31,17 +38,24 @@
 	};
 };
 
+&sound {
+	hp-det-gpio = <&gpio1 RK_PA0 GPIO_ACTIVE_HIGH>;
+};
+
 &uart0 {
 	status = "okay";
 
 	bluetooth {
-		compatible = "brcm,bcm43438-bt";
+		compatible = "brcm,bcm4345c5";
 		clocks = <&rk808 1>;
-		clock-names = "ext_clock";
+		clock-names = "lpo";
 		device-wakeup-gpios = <&gpio2 RK_PD3 GPIO_ACTIVE_HIGH>;
 		host-wakeup-gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_HIGH>;
 		shutdown-gpios = <&gpio0 RK_PB1 GPIO_ACTIVE_HIGH>;
+		max-speed = <1500000>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&bt_host_wake_l &bt_wake_l &bt_enable_h>;
+		vbat-supply = <&vcc3v3_sys>;
+		vddio-supply = <&vcc_1v8>;
 	};
 };
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-rock-pi-4b.dts b/arch/arm64/boot/dts/rockchip/rk3399-rock-pi-4b.dts
index 6c63e617063c..0806545922f5 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-rock-pi-4b.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3399-rock-pi-4b.dts
@@ -23,7 +23,7 @@
 		compatible = "brcm,bcm4329-fmac";
 		reg = <1>;
 		interrupt-parent = <&gpio0>;
-		interrupts = <RK_PA3 GPIO_ACTIVE_HIGH>;
+		interrupts = <RK_PA3 IRQ_TYPE_LEVEL_HIGH>;
 		interrupt-names = "host-wake";
 		pinctrl-names = "default";
 		pinctrl-0 = <&wifi_host_wake_l>;
@@ -34,13 +34,16 @@
 	status = "okay";
 
 	bluetooth {
-		compatible = "brcm,bcm43438-bt";
+		compatible = "brcm,bcm4345c5";
 		clocks = <&rk808 1>;
-		clock-names = "ext_clock";
+		clock-names = "lpo";
 		device-wakeup-gpios = <&gpio2 RK_PD3 GPIO_ACTIVE_HIGH>;
 		host-wakeup-gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_HIGH>;
 		shutdown-gpios = <&gpio0 RK_PB1 GPIO_ACTIVE_HIGH>;
+		max-speed = <1500000>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&bt_host_wake_l &bt_wake_l &bt_enable_h>;
+		vbat-supply = <&vcc3v3_sys>;
+		vddio-supply = <&vcc_1v8>;
 	};
 };
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-rock-pi-4c.dts b/arch/arm64/boot/dts/rockchip/rk3399-rock-pi-4c.dts
index 99169bcd51c0..4053ba72618c 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-rock-pi-4c.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3399-rock-pi-4c.dts
@@ -17,6 +17,13 @@
 	};
 };
 
+&es8316 {
+	pinctrl-0 = <&hp_detect &hp_int>;
+	pinctrl-names = "default";
+	interrupt-parent = <&gpio1>;
+	interrupts = <RK_PA1 IRQ_TYPE_LEVEL_HIGH>;
+};
+
 &sdio0 {
 	status = "okay";
 
@@ -24,25 +31,32 @@
 		compatible = "brcm,bcm4329-fmac";
 		reg = <1>;
 		interrupt-parent = <&gpio0>;
-		interrupts = <RK_PA3 GPIO_ACTIVE_HIGH>;
+		interrupts = <RK_PA3 IRQ_TYPE_LEVEL_HIGH>;
 		interrupt-names = "host-wake";
 		pinctrl-names = "default";
 		pinctrl-0 = <&wifi_host_wake_l>;
 	};
 };
 
+&sound {
+	hp-det-gpio = <&gpio1 RK_PA0 GPIO_ACTIVE_HIGH>;
+};
+
 &uart0 {
 	status = "okay";
 
 	bluetooth {
-		compatible = "brcm,bcm43438-bt";
+		compatible = "brcm,bcm4345c5";
 		clocks = <&rk808 1>;
-		clock-names = "ext_clock";
+		clock-names = "lpo";
 		device-wakeup-gpios = <&gpio2 RK_PD3 GPIO_ACTIVE_HIGH>;
 		host-wakeup-gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_HIGH>;
 		shutdown-gpios = <&gpio0 RK_PB1 GPIO_ACTIVE_HIGH>;
+		max-speed = <1500000>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&bt_host_wake_l &bt_wake_l &bt_enable_h>;
+		vbat-supply = <&vcc3v3_sys>;
+		vddio-supply = <&vcc_1v8>;
 	};
 };
 
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-rock960.dtsi b/arch/arm64/boot/dts/rockchip/rk3399-rock960.dtsi
index 25dc61c26a94..94e39ed63397 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-rock960.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3399-rock960.dtsi
@@ -7,6 +7,7 @@
 
 #include "rk3399.dtsi"
 #include "rk3399-opp.dtsi"
+#include <dt-bindings/interrupt-controller/irq.h>
 
 / {
 	aliases {
@@ -528,7 +529,7 @@
 		compatible = "brcm,bcm4329-fmac";
 		reg = <1>;
 		interrupt-parent = <&gpio0>;
-		interrupts = <RK_PA3 GPIO_ACTIVE_HIGH>;
+		interrupts = <RK_PA3 IRQ_TYPE_LEVEL_HIGH>;
 		interrupt-names = "host-wake";
 		pinctrl-names = "default";
 		pinctrl-0 = <&wifi_host_wake_l>;
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-rockpro64.dtsi b/arch/arm64/boot/dts/rockchip/rk3399-rockpro64.dtsi
index 83db4ca67334..78157521e944 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-rockpro64.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3399-rockpro64.dtsi
@@ -20,6 +20,15 @@
 		stdout-path = "serial2:1500000n8";
 	};
 
+	/* enable for panel backlight support */
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		brightness-levels = <0 4 8 16 32 64 128 255>;
+		default-brightness-level = <5>;
+		pwms = <&pwm0 0 1000000 0>;
+		status = "disabled";
+	};
+
 	clkin_gmac: external-gmac-clock {
 		compatible = "fixed-clock";
 		clock-frequency = <125000000>;
@@ -33,7 +42,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pwrbtn>;
 
-		power {
+		key-power {
 			debounce-interval = <100>;
 			gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_LOW>;
 			label = "GPIO Key Power";
@@ -107,6 +116,14 @@
 		};
 	};
 
+	avdd: avdd-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "avdd";
+		regulator-min-microvolt = <11000000>;
+		regulator-max-microvolt = <11000000>;
+		vin-supply = <&vcc3v3_s0>;
+	};
+
 	vcc12v_dcin: vcc12v-dcin {
 		compatible = "regulator-fixed";
 		regulator-name = "vcc12v_dcin";
@@ -213,12 +230,12 @@
 	vdd_log: vdd-log {
 		compatible = "pwm-regulator";
 		pwms = <&pwm2 0 25000 1>;
+		pwm-supply = <&vcc5v0_sys>;
 		regulator-name = "vdd_log";
 		regulator-always-on;
 		regulator-boot-on;
 		regulator-min-microvolt = <800000>;
 		regulator-max-microvolt = <1700000>;
-		vin-supply = <&vcc5v0_sys>;
 	};
 };
 
@@ -400,8 +417,6 @@
 
 			vcc3v0_touch: LDO_REG2 {
 				regulator-name = "vcc3v0_touch";
-				regulator-always-on;
-				regulator-boot-on;
 				regulator-min-microvolt = <3000000>;
 				regulator-max-microvolt = <3000000>;
 				regulator-state-mem {
@@ -490,8 +505,6 @@
 
 			vcc3v3_s0: SWITCH_REG2 {
 				regulator-name = "vcc3v3_s0";
-				regulator-always-on;
-				regulator-boot-on;
 				regulator-state-mem {
 					regulator-off-in-suspend;
 				};
@@ -565,6 +578,19 @@
 		vbus-supply = <&vcc5v0_typec>;
 		status = "okay";
 	};
+
+	/* enable for pine64 touch screen support */
+	touch: touchscreen@5d {
+		compatible = "goodix,gt911";
+		reg = <0x5d>;
+		interrupt-parent = <&gpio4>;
+		interrupts = <RK_PD5 IRQ_TYPE_EDGE_FALLING>;
+		AVDD28-supply = <&vcc3v0_touch>;
+		VDDIO-supply = <&vcc3v0_touch>;
+		irq-gpios = <&gpio4 RK_PD5 GPIO_ACTIVE_HIGH>;
+		reset-gpios = <&gpio4 RK_PD6 GPIO_ACTIVE_HIGH>;
+		status = "disabled";
+	};
 };
 
 &i2s0 {
@@ -600,6 +626,42 @@
 	gpio1830-supply = <&vcc_3v0>;
 };
 
+/* enable for pine64 panel display support */
+&mipi_dsi {
+	clock-master;
+	status = "disabled";
+
+	ports {
+		mipi_out: port@1 {
+			reg = <1>;
+
+			mipi_out_panel: endpoint {
+				remote-endpoint = <&mipi_in_panel>;
+			};
+		};
+	};
+
+	mipi_panel: panel@0 {
+		compatible = "feiyang,fy07024di26a30d";
+		reg = <0>;
+		avdd-supply = <&avdd>;
+		backlight = <&backlight>;
+		dvdd-supply = <&vcc3v3_s0>;
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				mipi_in_panel: endpoint {
+					remote-endpoint = <&mipi_out_panel>;
+				};
+			};
+		};
+	};
+};
+
 &pcie0 {
 	ep-gpios = <&gpio2 RK_PD4 GPIO_ACTIVE_HIGH>;
 	num-lanes = <4>;
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-sapphire-excavator.dts b/arch/arm64/boot/dts/rockchip/rk3399-sapphire-excavator.dts
index f6b2199a42bd..13927e7d0724 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-sapphire-excavator.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3399-sapphire-excavator.dts
@@ -88,7 +88,7 @@
 	};
 
 	edp_panel: edp-panel {
-		compatible ="lg,lp079qx1-sp0v";
+		compatible = "lg,lp079qx1-sp0v";
 		backlight = <&backlight>;
 		enable-gpios = <&gpio4 RK_PC6 GPIO_ACTIVE_HIGH>;
 		pinctrl-names = "default";
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-sapphire.dtsi b/arch/arm64/boot/dts/rockchip/rk3399-sapphire.dtsi
index 46b0f97a0b1c..e6ac292ce645 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-sapphire.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3399-sapphire.dtsi
@@ -53,7 +53,7 @@
 		compatible = "gpio-keys";
 		autorepeat;
 
-		power {
+		key-power {
 			debounce-interval = <100>;
 			gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_LOW>;
 			label = "GPIO Power";
@@ -133,12 +133,12 @@
 	vdd_log: vdd-log {
 		compatible = "pwm-regulator";
 		pwms = <&pwm2 0 25000 1>;
+		pwm-supply = <&vcc_sys>;
 		regulator-name = "vdd_log";
 		regulator-always-on;
 		regulator-boot-on;
 		regulator-min-microvolt = <800000>;
 		regulator-max-microvolt = <1400000>;
-		vin-supply = <&vcc_sys>;
 	};
 };
 
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-t-opp.dtsi b/arch/arm64/boot/dts/rockchip/rk3399-t-opp.dtsi
new file mode 100644
index 000000000000..1ababadda9df
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3399-t-opp.dtsi
@@ -0,0 +1,114 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2016-2017 Fuzhou Rockchip Electronics Co., Ltd
+ * Copyright (c) 2022 Radxa Limited
+ */
+
+/ {
+	cluster0_opp: opp-table-0 {
+		compatible = "operating-points-v2";
+		opp-shared;
+
+		opp00 {
+			opp-hz = /bits/ 64 <408000000>;
+			opp-microvolt = <875000 875000 1250000>;
+			clock-latency-ns = <40000>;
+		};
+		opp01 {
+			opp-hz = /bits/ 64 <600000000>;
+			opp-microvolt = <875000 875000 1250000>;
+		};
+		opp02 {
+			opp-hz = /bits/ 64 <816000000>;
+			opp-microvolt = <900000 900000 1250000>;
+		};
+		opp03 {
+			opp-hz = /bits/ 64 <1008000000>;
+			opp-microvolt = <975000 975000 1250000>;
+		};
+	};
+
+	cluster1_opp: opp-table-1 {
+		compatible = "operating-points-v2";
+		opp-shared;
+
+		opp00 {
+			opp-hz = /bits/ 64 <408000000>;
+			opp-microvolt = <875000 875000 1250000>;
+			clock-latency-ns = <40000>;
+		};
+		opp01 {
+			opp-hz = /bits/ 64 <600000000>;
+			opp-microvolt = <875000 875000 1250000>;
+		};
+		opp02 {
+			opp-hz = /bits/ 64 <816000000>;
+			opp-microvolt = <875000 875000 1250000>;
+		};
+		opp03 {
+			opp-hz = /bits/ 64 <1008000000>;
+			opp-microvolt = <925000 925000 1250000>;
+		};
+		opp04 {
+			opp-hz = /bits/ 64 <1200000000>;
+			opp-microvolt = <1000000 1000000 1250000>;
+		};
+		opp05 {
+			opp-hz = /bits/ 64 <1416000000>;
+			opp-microvolt = <1075000 1075000 1250000>;
+		};
+		opp06 {
+			opp-hz = /bits/ 64 <1512000000>;
+			opp-microvolt = <1150000 1150000 1250000>;
+		};
+	};
+
+	gpu_opp_table: opp-table-2 {
+		compatible = "operating-points-v2";
+
+		opp00 {
+			opp-hz = /bits/ 64 <200000000>;
+			opp-microvolt = <875000 875000 1150000>;
+		};
+		opp01 {
+			opp-hz = /bits/ 64 <300000000>;
+			opp-microvolt = <875000 875000 1150000>;
+		};
+		opp02 {
+			opp-hz = /bits/ 64 <400000000>;
+			opp-microvolt = <875000 875000 1150000>;
+		};
+		opp03 {
+			opp-hz = /bits/ 64 <600000000>;
+			opp-microvolt = <975000 975000 1150000>;
+		};
+	};
+};
+
+&cpu_l0 {
+	operating-points-v2 = <&cluster0_opp>;
+};
+
+&cpu_l1 {
+	operating-points-v2 = <&cluster0_opp>;
+};
+
+&cpu_l2 {
+	operating-points-v2 = <&cluster0_opp>;
+};
+
+&cpu_l3 {
+	operating-points-v2 = <&cluster0_opp>;
+};
+
+&cpu_b0 {
+	operating-points-v2 = <&cluster1_opp>;
+};
+
+&cpu_b1 {
+	operating-points-v2 = <&cluster1_opp>;
+};
+
+&gpu {
+	operating-points-v2 = <&gpu_opp_table>;
+};
diff --git a/arch/arm64/boot/dts/rockchip/rk3399.dtsi b/arch/arm64/boot/dts/rockchip/rk3399.dtsi
index d3cdf6f42a30..92c2207e686c 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3399.dtsi
@@ -178,6 +178,15 @@
 		ports = <&vopl_out>, <&vopb_out>;
 	};
 
+	dmc: memory-controller {
+		compatible = "rockchip,rk3399-dmc";
+		rockchip,pmu = <&pmugrf>;
+		devfreq-events = <&dfi>;
+		clocks = <&cru SCLK_DDRC>;
+		clock-names = "dmc_clk";
+		status = "disabled";
+	};
+
 	pmu_a53 {
 		compatible = "arm,cortex-a53-pmu";
 		interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_LOW &ppi_cluster0>;
@@ -1295,6 +1304,16 @@
 		status = "disabled";
 	};
 
+	dfi: dfi@ff630000 {
+		reg = <0x00 0xff630000 0x00 0x4000>;
+		compatible = "rockchip,rk3399-dfi";
+		rockchip,pmu = <&pmugrf>;
+		interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH 0>;
+		clocks = <&cru PCLK_DDR_MON>;
+		clock-names = "pclk_ddr_mon";
+		status = "disabled";
+	};
+
 	vpu: video-codec@ff650000 {
 		compatible = "rockchip,rk3399-vpu";
 		reg = <0x0 0xff650000 0x0 0x800>;
@@ -1413,9 +1432,11 @@
 		clock-names = "apb_pclk";
 	};
 
-	pmucru: pmu-clock-controller@ff750000 {
+	pmucru: clock-controller@ff750000 {
 		compatible = "rockchip,rk3399-pmucru";
 		reg = <0x0 0xff750000 0x0 0x1000>;
+		clocks = <&xin24m>;
+		clock-names = "xin24m";
 		rockchip,grf = <&pmugrf>;
 		#clock-cells = <1>;
 		#reset-cells = <1>;
@@ -1426,6 +1447,8 @@
 	cru: clock-controller@ff760000 {
 		compatible = "rockchip,rk3399-cru";
 		reg = <0x0 0xff760000 0x0 0x1000>;
+		clocks = <&xin24m>;
+		clock-names = "xin24m";
 		rockchip,grf = <&grf>;
 		#clock-cells = <1>;
 		#reset-cells = <1>;
@@ -1439,7 +1462,8 @@
 			<&cru HCLK_PERILP1>, <&cru PCLK_PERILP1>,
 			<&cru ACLK_VIO>, <&cru ACLK_HDCP>,
 			<&cru ACLK_GIC_PRE>,
-			<&cru PCLK_DDR>;
+			<&cru PCLK_DDR>,
+			<&cru ACLK_VDU>;
 		assigned-clock-rates =
 			 <594000000>,  <800000000>,
 			<1000000000>,
@@ -1450,7 +1474,8 @@
 			 <100000000>,   <50000000>,
 			 <400000000>, <400000000>,
 			 <200000000>,
-			 <200000000>;
+			 <200000000>,
+			 <400000000>;
 	};
 
 	grf: syscon@ff770000 {
@@ -1534,6 +1559,7 @@
 			reg = <0xf780 0x24>;
 			clocks = <&sdhci>;
 			clock-names = "emmcclk";
+			drive-impedance-ohm = <50>;
 			#phy-cells = <0>;
 			status = "disabled";
 		};
@@ -1544,7 +1570,6 @@
 			clock-names = "refclk";
 			#phy-cells = <1>;
 			resets = <&cru SRST_PCIEPHY>;
-			drive-impedance-ohm = <50>;
 			reset-names = "phy";
 			status = "disabled";
 		};
@@ -1639,8 +1664,9 @@
 		dma-names = "tx", "rx";
 		clock-names = "i2s_clk", "i2s_hclk";
 		clocks = <&cru SCLK_I2S0_8CH>, <&cru HCLK_I2S0_8CH>;
-		pinctrl-names = "default";
+		pinctrl-names = "bclk_on", "bclk_off";
 		pinctrl-0 = <&i2s0_8ch_bus>;
+		pinctrl-1 = <&i2s0_8ch_bus_bclk_off>;
 		power-domains = <&power RK3399_PD_SDIOAUDIO>;
 		#sound-dai-cells = <0>;
 		status = "disabled";
@@ -1676,7 +1702,7 @@
 
 	vopl: vop@ff8f0000 {
 		compatible = "rockchip,rk3399-vop-lit";
-		reg = <0x0 0xff8f0000 0x0 0x3efc>;
+		reg = <0x0 0xff8f0000 0x0 0x2000>, <0x0 0xff8f2000 0x0 0x400>;
 		interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH 0>;
 		assigned-clocks = <&cru ACLK_VOP1>, <&cru HCLK_VOP1>;
 		assigned-clock-rates = <400000000>, <100000000>;
@@ -1732,7 +1758,7 @@
 
 	vopb: vop@ff900000 {
 		compatible = "rockchip,rk3399-vop-big";
-		reg = <0x0 0xff900000 0x0 0x3efc>;
+		reg = <0x0 0xff900000 0x0 0x2000>, <0x0 0xff902000 0x0 0x1000>;
 		interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH 0>;
 		assigned-clocks = <&cru ACLK_VOP0>, <&cru HCLK_VOP0>;
 		assigned-clock-rates = <400000000>, <100000000>;
@@ -1881,10 +1907,10 @@
 		interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH 0>;
 		clocks = <&cru PCLK_HDMI_CTRL>,
 			 <&cru SCLK_HDMI_SFR>,
-			 <&cru PLL_VPLL>,
+			 <&cru SCLK_HDMI_CEC>,
 			 <&cru PCLK_VIO_GRF>,
-			 <&cru SCLK_HDMI_CEC>;
-		clock-names = "iahb", "isfr", "vpll", "grf", "cec";
+			 <&cru PLL_VPLL>;
+		clock-names = "iahb", "isfr", "cec", "grf", "ref";
 		power-domains = <&power RK3399_PD_HDCP>;
 		reg-io-width = <4>;
 		rockchip,grf = <&grf>;
@@ -2188,6 +2214,22 @@
 			output-low;
 		};
 
+		pcfg_input_enable: pcfg-input-enable {
+			input-enable;
+		};
+
+		pcfg_input_pull_up: pcfg-input-pull-up {
+			input-enable;
+			bias-pull-up;
+			drive-strength = <2>;
+		};
+
+		pcfg_input_pull_down: pcfg-input-pull-down {
+			input-enable;
+			bias-pull-down;
+			drive-strength = <2>;
+		};
+
 		clock {
 			clk_32k: clk-32k {
 				rockchip,pins = <0 RK_PA0 2 &pcfg_pull_none>;
@@ -2368,6 +2410,19 @@
 					<3 RK_PD7 1 &pcfg_pull_none>,
 					<4 RK_PA0 1 &pcfg_pull_none>;
 			};
+
+			i2s0_8ch_bus_bclk_off: i2s0-8ch-bus-bclk-off {
+				rockchip,pins =
+					<3 RK_PD0 RK_FUNC_GPIO &pcfg_pull_none>,
+					<3 RK_PD1 1 &pcfg_pull_none>,
+					<3 RK_PD2 1 &pcfg_pull_none>,
+					<3 RK_PD3 1 &pcfg_pull_none>,
+					<3 RK_PD4 1 &pcfg_pull_none>,
+					<3 RK_PD5 1 &pcfg_pull_none>,
+					<3 RK_PD6 1 &pcfg_pull_none>,
+					<3 RK_PD7 1 &pcfg_pull_none>,
+					<4 RK_PA0 1 &pcfg_pull_none>;
+			};
 		};
 
 		i2s1 {
@@ -2379,6 +2434,15 @@
 					<4 RK_PA6 1 &pcfg_pull_none>,
 					<4 RK_PA7 1 &pcfg_pull_none>;
 			};
+
+			i2s1_2ch_bus_bclk_off: i2s1-2ch-bus-bclk-off {
+				rockchip,pins =
+					<4 RK_PA3 RK_FUNC_GPIO &pcfg_pull_none>,
+					<4 RK_PA4 1 &pcfg_pull_none>,
+					<4 RK_PA5 1 &pcfg_pull_none>,
+					<4 RK_PA6 1 &pcfg_pull_none>,
+					<4 RK_PA7 1 &pcfg_pull_none>;
+			};
 		};
 
 		sdio0 {
diff --git a/arch/arm64/boot/dts/rockchip/rk3399pro-vmarc-som.dtsi b/arch/arm64/boot/dts/rockchip/rk3399pro-vmarc-som.dtsi
index 01d1a75c8b4d..935b8c68a71d 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399pro-vmarc-som.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3399pro-vmarc-som.dtsi
@@ -347,7 +347,7 @@
 
 	pcie {
 		pcie_pwr: pcie-pwr {
-			rockchip,pins =	<4 RK_PD4 RK_FUNC_GPIO &pcfg_pull_up>;
+			rockchip,pins = <4 RK_PD4 RK_FUNC_GPIO &pcfg_pull_up>;
 		};
 	};
 
diff --git a/arch/arm64/boot/dts/rockchip/rk3566-anbernic-rg353p.dts b/arch/arm64/boot/dts/rockchip/rk3566-anbernic-rg353p.dts
new file mode 100644
index 000000000000..7a20e2d6876a
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3566-anbernic-rg353p.dts
@@ -0,0 +1,94 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/pinctrl/rockchip.h>
+#include "rk3566-anbernic-rgxx3.dtsi"
+
+/ {
+	model = "RG353P";
+	compatible = "anbernic,rg353p", "rockchip,rk3566";
+
+	aliases {
+		mmc0 = &sdhci;
+		mmc1 = &sdmmc0;
+		mmc2 = &sdmmc1;
+		mmc3 = &sdmmc2;
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		power-supply = <&vcc_sys>;
+		pwms = <&pwm4 0 25000 0>;
+	};
+};
+
+&gpio_keys_control {
+	button-a {
+		gpios = <&gpio3 RK_PC2 GPIO_ACTIVE_LOW>;
+		label = "EAST";
+		linux,code = <BTN_EAST>;
+	};
+
+	button-left {
+		gpios = <&gpio3 RK_PA6 GPIO_ACTIVE_LOW>;
+		label = "DPAD-LEFT";
+		linux,code = <BTN_DPAD_LEFT>;
+	};
+
+	button-r1 {
+		gpios = <&gpio3 RK_PB4 GPIO_ACTIVE_LOW>;
+		label = "TR";
+		linux,code = <BTN_TR>;
+	};
+
+	button-r2 {
+		gpios = <&gpio3 RK_PB3 GPIO_ACTIVE_LOW>;
+		label = "TR2";
+		linux,code = <BTN_TR2>;
+	};
+
+	button-right {
+		gpios = <&gpio3 RK_PA5 GPIO_ACTIVE_LOW>;
+		label = "DPAD-RIGHT";
+		linux,code = <BTN_DPAD_RIGHT>;
+	};
+
+	button-y {
+		gpios = <&gpio3 RK_PC1 GPIO_ACTIVE_LOW>;
+		label = "WEST";
+		linux,code = <BTN_WEST>;
+	};
+};
+
+&i2c0 {
+	/* This hardware is physically present but unused. */
+	power-monitor@62 {
+		compatible = "cellwise,cw2015";
+		reg = <0x62>;
+		status = "disabled";
+	};
+};
+
+&i2c2 {
+	pintctrl-names = "default";
+	pinctrl-0 = <&i2c2m1_xfer>;
+	status = "okay";
+};
+
+&pwm4 {
+	status = "okay";
+};
+
+&sdhci {
+	pinctrl-0 = <&emmc_bus8>, <&emmc_clk>, <&emmc_cmd>, <&emmc_datastrobe>, <&emmc_rstnout>;
+	pinctrl-names = "default";
+	bus-width = <8>;
+	mmc-hs200-1_8v;
+	non-removable;
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&vcc_1v8>;
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/rockchip/rk3566-anbernic-rg503.dts b/arch/arm64/boot/dts/rockchip/rk3566-anbernic-rg503.dts
new file mode 100644
index 000000000000..3dc01549a5b4
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3566-anbernic-rg503.dts
@@ -0,0 +1,87 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/pinctrl/rockchip.h>
+#include "rk3566-anbernic-rgxx3.dtsi"
+
+/ {
+	model = "RG503";
+	compatible = "anbernic,rg503", "rockchip,rk3566";
+
+	aliases {
+		mmc0 = &sdmmc0;
+		mmc1 = &sdmmc1;
+		mmc2 = &sdmmc2;
+	};
+
+	gpio_spi: spi {
+		compatible = "spi-gpio";
+		pinctrl-names = "default";
+		pinctrl-0 = <&spi_pins>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		sck-gpios = <&gpio4 RK_PB3 GPIO_ACTIVE_HIGH>;
+		mosi-gpios = <&gpio4 RK_PB0 GPIO_ACTIVE_HIGH>;
+		cs-gpios = <&gpio4 RK_PA7 GPIO_ACTIVE_HIGH>;
+		num-chipselects = <0>;
+	};
+};
+
+&gpio_keys_control {
+	button-a {
+		gpios = <&gpio3 RK_PC1 GPIO_ACTIVE_LOW>;
+		label = "EAST";
+		linux,code = <BTN_EAST>;
+	};
+
+	button-left {
+		gpios = <&gpio3 RK_PA5 GPIO_ACTIVE_LOW>;
+		label = "DPAD-LEFT";
+		linux,code = <BTN_DPAD_LEFT>;
+	};
+
+	button-right {
+		gpios = <&gpio3 RK_PA6 GPIO_ACTIVE_LOW>;
+		label = "DPAD-RIGHT";
+		linux,code = <BTN_DPAD_RIGHT>;
+	};
+
+	button-r1 {
+		gpios = <&gpio3 RK_PB3 GPIO_ACTIVE_LOW>;
+		label = "TR";
+		linux,code = <BTN_TR>;
+	};
+
+	button-r2 {
+		gpios = <&gpio3 RK_PB4 GPIO_ACTIVE_LOW>;
+		label = "TR2";
+		linux,code = <BTN_TR2>;
+	};
+
+	button-right {
+		gpios = <&gpio3 RK_PA6 GPIO_ACTIVE_LOW>;
+		label = "DPAD-RIGHT";
+		linux,code = <BTN_DPAD_RIGHT>;
+	};
+
+	button-y {
+		gpios = <&gpio3 RK_PC2 GPIO_ACTIVE_LOW>;
+		label = "WEST";
+		linux,code = <BTN_WEST>;
+	};
+};
+
+&pinctrl {
+	gpio-spi {
+		spi_pins: spi-pins {
+			rockchip,pins =
+				<4 RK_PA7 RK_FUNC_GPIO &pcfg_pull_none>,
+				<4 RK_PB0 RK_FUNC_GPIO &pcfg_pull_none>,
+				<4 RK_PB3 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+};
diff --git a/arch/arm64/boot/dts/rockchip/rk3566-anbernic-rgxx3.dtsi b/arch/arm64/boot/dts/rockchip/rk3566-anbernic-rgxx3.dtsi
new file mode 100644
index 000000000000..2b455143b86d
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3566-anbernic-rgxx3.dtsi
@@ -0,0 +1,831 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/rockchip.h>
+#include <dt-bindings/soc/rockchip,vop2.h>
+#include "rk3566.dtsi"
+
+/ {
+	chosen: chosen {
+		stdout-path = "serial2:1500000n8";
+	};
+
+	adc-joystick {
+		compatible = "adc-joystick";
+		io-channels = <&adc_mux 0>,
+			      <&adc_mux 1>,
+			      <&adc_mux 2>,
+			      <&adc_mux 3>;
+		pinctrl-0 = <&joy_mux_en>;
+		pinctrl-names = "default";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		axis@0 {
+			reg = <0>;
+			abs-flat = <32>;
+			abs-fuzz = <32>;
+			abs-range = <1023 15>;
+			linux,code = <ABS_X>;
+		};
+
+		axis@1 {
+			reg = <1>;
+			abs-flat = <32>;
+			abs-fuzz = <32>;
+			abs-range = <15 1023>;
+			linux,code = <ABS_RX>;
+		};
+
+		axis@2 {
+			reg = <2>;
+			abs-flat = <32>;
+			abs-fuzz = <32>;
+			abs-range = <15 1023>;
+			linux,code = <ABS_Y>;
+		};
+
+		axis@3 {
+			reg = <3>;
+			abs-flat = <32>;
+			abs-fuzz = <32>;
+			abs-range = <1023 15>;
+			linux,code = <ABS_RY>;
+		};
+	};
+
+	adc_keys: adc-keys {
+		compatible = "adc-keys";
+		io-channels = <&saradc 0>;
+		io-channel-names = "buttons";
+		keyup-threshold-microvolt = <1800000>;
+		poll-interval = <60>;
+
+		/*
+		 * Button is mapped to F key in BSP kernel, but
+		 * according to input guidelines it should be mode.
+		 */
+		button-mode {
+			label = "MODE";
+			linux,code = <BTN_MODE>;
+			press-threshold-microvolt = <1750>;
+		};
+	};
+
+	adc_mux: adc-mux {
+		compatible = "io-channel-mux";
+		channels = "left_x", "right_x", "left_y", "right_y";
+		#io-channel-cells = <1>;
+		io-channels = <&saradc 3>;
+		io-channel-names = "parent";
+		mux-controls = <&gpio_mux>;
+		settle-time-us = <100>;
+	};
+
+	gpio_keys_control: gpio-keys-control {
+		compatible = "gpio-keys";
+		pinctrl-0 = <&btn_pins_ctrl>;
+		pinctrl-names = "default";
+
+		button-b {
+			gpios = <&gpio3 RK_PC3 GPIO_ACTIVE_LOW>;
+			label = "SOUTH";
+			linux,code = <BTN_SOUTH>;
+		};
+
+		button-down {
+			gpios = <&gpio3 RK_PA4 GPIO_ACTIVE_LOW>;
+			label = "DPAD-DOWN";
+			linux,code = <BTN_DPAD_DOWN>;
+		};
+
+		button-l1 {
+			gpios = <&gpio3 RK_PB1 GPIO_ACTIVE_LOW>;
+			label = "TL";
+			linux,code = <BTN_TL>;
+		};
+
+		button-l2 {
+			gpios = <&gpio3 RK_PB2 GPIO_ACTIVE_LOW>;
+			label = "TL2";
+			linux,code = <BTN_TL2>;
+		};
+
+		button-select {
+			gpios = <&gpio3 RK_PB6 GPIO_ACTIVE_LOW>;
+			label = "SELECT";
+			linux,code = <BTN_SELECT>;
+		};
+
+		button-start {
+			gpios = <&gpio3 RK_PB5 GPIO_ACTIVE_LOW>;
+			label = "START";
+			linux,code = <BTN_START>;
+		};
+
+		button-thumbl {
+			gpios = <&gpio3 RK_PA1 GPIO_ACTIVE_LOW>;
+			label = "THUMBL";
+			linux,code = <BTN_THUMBL>;
+		};
+
+		button-thumbr {
+			gpios = <&gpio3 RK_PA2 GPIO_ACTIVE_LOW>;
+			label = "THUMBR";
+			linux,code = <BTN_THUMBR>;
+		};
+
+		button-up {
+			gpios = <&gpio3 RK_PA3 GPIO_ACTIVE_LOW>;
+			label = "DPAD-UP";
+			linux,code = <BTN_DPAD_UP>;
+		};
+
+		button-x {
+			gpios = <&gpio3 RK_PC0 GPIO_ACTIVE_LOW>;
+			label = "NORTH";
+			linux,code = <BTN_NORTH>;
+		};
+	};
+
+	gpio_keys_vol: gpio-keys-vol {
+		compatible = "gpio-keys";
+		autorepeat;
+		pinctrl-0 = <&btn_pins_vol>;
+		pinctrl-names = "default";
+
+		button-vol-down {
+			gpios = <&gpio3 RK_PB0 GPIO_ACTIVE_LOW>;
+			label = "VOLUMEDOWN";
+			linux,code = <KEY_VOLUMEDOWN>;
+		};
+
+		button-vol-up {
+			gpios = <&gpio3 RK_PA7 GPIO_ACTIVE_LOW>;
+			label = "VOLUMEUP";
+			linux,code = <KEY_VOLUMEUP>;
+		};
+	};
+
+	gpio_mux: mux-controller {
+		compatible = "gpio-mux";
+		mux-gpios = <&gpio0 RK_PB6 GPIO_ACTIVE_LOW>,
+			    <&gpio0 RK_PB7 GPIO_ACTIVE_LOW>;
+		#mux-control-cells = <0>;
+	};
+
+	hdmi-con {
+		compatible = "hdmi-connector";
+		ddc-i2c-bus = <&i2c5>;
+		type = "c";
+
+		port {
+			hdmi_con_in: endpoint {
+				remote-endpoint = <&hdmi_out_con>;
+			};
+		};
+	};
+
+	leds: gpio-leds {
+		compatible = "gpio-leds";
+		pinctrl-0 = <&led_pins>;
+		pinctrl-names = "default";
+
+		green_led: led-0 {
+			color = <LED_COLOR_ID_GREEN>;
+			default-state = "on";
+			function = LED_FUNCTION_POWER;
+			gpios = <&gpio0 RK_PC5 GPIO_ACTIVE_HIGH>;
+		};
+
+		amber_led: led-1 {
+			color = <LED_COLOR_ID_AMBER>;
+			function = LED_FUNCTION_CHARGING;
+			gpios = <&gpio0 RK_PC6 GPIO_ACTIVE_HIGH>;
+			retain-state-suspended;
+		};
+
+		red_led: led-2 {
+			color = <LED_COLOR_ID_RED>;
+			default-state = "off";
+			function = LED_FUNCTION_STATUS;
+			gpios = <&gpio0 RK_PC7 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	/* Channels reversed for both headphones and speakers. */
+	sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "anbernic_rk817";
+		simple-audio-card,aux-devs = <&spk_amp>;
+		simple-audio-card,format = "i2s";
+		simple-audio-card,hp-det-gpio = <&gpio4 RK_PC6 GPIO_ACTIVE_HIGH>;
+		simple-audio-card,mclk-fs = <256>;
+		simple-audio-card,widgets =
+			"Microphone", "Mic Jack",
+			"Headphone", "Headphones",
+			"Speaker", "Internal Speakers";
+		simple-audio-card,routing =
+			"MICL", "Mic Jack",
+			"Headphones", "HPOL",
+			"Headphones", "HPOR",
+			"Internal Speakers", "Speaker Amp OUTL",
+			"Internal Speakers", "Speaker Amp OUTR",
+			"Speaker Amp INL", "HPOL",
+			"Speaker Amp INR", "HPOR";
+		simple-audio-card,pin-switches = "Internal Speakers";
+
+		simple-audio-card,codec {
+			sound-dai = <&rk817>;
+		};
+
+		simple-audio-card,cpu {
+			sound-dai = <&i2s1_8ch>;
+		};
+	};
+
+	sdio_pwrseq: sdio-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		clocks = <&rk817 1>;
+		clock-names = "ext_clock";
+		pinctrl-0 = <&wifi_enable_h>;
+		pinctrl-names = "default";
+		post-power-on-delay-ms = <200>;
+		reset-gpios = <&gpio4 RK_PA2 GPIO_ACTIVE_LOW>;
+	};
+
+	spk_amp: audio-amplifier {
+		compatible = "simple-audio-amplifier";
+		enable-gpios = <&gpio4 RK_PC2 GPIO_ACTIVE_HIGH>;
+		pinctrl-0 = <&spk_amp_enable_h>;
+		pinctrl-names = "default";
+		sound-name-prefix = "Speaker Amp";
+	};
+
+	vcc3v3_lcd0_n: regulator-vcc3v3-lcd0 {
+		compatible = "regulator-fixed";
+		gpio = <&gpio0 RK_PC2 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		pinctrl-0 = <&vcc_lcd_h>;
+		pinctrl-names = "default";
+		regulator-boot-on;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-name = "vcc3v3_lcd0_n";
+		vin-supply = <&vcc_3v3>;
+		regulator-state-mem {
+			regulator-off-in-suspend;
+		};
+	};
+
+	vcc_sys: regulator-vcc-sys {
+		compatible = "regulator-fixed";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <3800000>;
+		regulator-max-microvolt = <3800000>;
+		regulator-name = "vcc_sys";
+	};
+
+	vcc_wifi: regulator-vcc-wifi {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio0 RK_PA0 GPIO_ACTIVE_HIGH>;
+		pinctrl-0 = <&vcc_wifi_h>;
+		pinctrl-names = "default";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-name = "vcc_wifi";
+	};
+
+	vibrator: pwm-vibrator {
+		compatible = "pwm-vibrator";
+		pwm-names = "enable";
+		pwms = <&pwm5 0 1000000000 0>;
+	};
+};
+
+&combphy1 {
+	status = "okay";
+};
+
+&cpu0 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&cpu1 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&cpu2 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&cpu3 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&gpu {
+	mali-supply = <&vdd_gpu>;
+	status = "okay";
+};
+
+&hdmi {
+	ddc-i2c-bus = <&i2c5>;
+	pinctrl-0 = <&hdmitxm0_cec>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&hdmi_in {
+	hdmi_in_vp0: endpoint {
+		remote-endpoint = <&vp0_out_hdmi>;
+	};
+};
+
+&hdmi_out {
+	hdmi_out_con: endpoint {
+		remote-endpoint = <&hdmi_con_in>;
+	};
+};
+
+&hdmi_sound {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	rk817: pmic@20 {
+		compatible = "rockchip,rk817";
+		reg = <0x20>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <RK_PA3 IRQ_TYPE_LEVEL_LOW>;
+		clock-output-names = "rk808-clkout1", "rk808-clkout2";
+		clock-names = "mclk";
+		clocks = <&cru I2S1_MCLKOUT_TX>;
+		assigned-clocks = <&cru I2S1_MCLKOUT_TX>;
+		assigned-clock-parents = <&cru CLK_I2S1_8CH_TX>;
+		#clock-cells = <1>;
+		#sound-dai-cells = <0>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2s1m0_mclk>, <&pmic_int_l>;
+		wakeup-source;
+
+		vcc1-supply = <&vcc_sys>;
+		vcc2-supply = <&vcc_sys>;
+		vcc3-supply = <&vcc_sys>;
+		vcc4-supply = <&vcc_sys>;
+		vcc5-supply = <&vcc_sys>;
+		vcc6-supply = <&vcc_sys>;
+		vcc7-supply = <&vcc_sys>;
+		vcc8-supply = <&vcc_sys>;
+		vcc9-supply = <&dcdc_boost>;
+
+		regulators {
+			vdd_logic: DCDC_REG1 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-init-microvolt = <900000>;
+				regulator-ramp-delay = <6001>;
+				regulator-initial-mode = <0x2>;
+				regulator-name = "vdd_logic";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+					regulator-suspend-microvolt = <900000>;
+				};
+			};
+
+			vdd_gpu: DCDC_REG2 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-init-microvolt = <900000>;
+				regulator-ramp-delay = <6001>;
+				regulator-initial-mode = <0x2>;
+				regulator-name = "vdd_gpu";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_ddr: DCDC_REG3 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-initial-mode = <0x2>;
+				regulator-name = "vcc_ddr";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vcc_3v3: DCDC_REG4 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-initial-mode = <0x2>;
+				regulator-name = "vcc_3v3";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+				};
+			};
+
+			vcca1v8_pmu: LDO_REG1 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcca1v8_pmu";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vdda_0v9: LDO_REG2 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <900000>;
+				regulator-name = "vdda_0v9";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdda0v9_pmu: LDO_REG3 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <900000>;
+				regulator-name = "vdda0v9_pmu";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <900000>;
+				};
+			};
+
+			vccio_acodec: LDO_REG4 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vccio_acodec";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vccio_sd: LDO_REG5 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vccio_sd";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc3v3_pmu: LDO_REG6 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc3v3_pmu";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+				};
+			};
+
+			vcc_1v8: LDO_REG7 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcc_1v8";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc1v8_dvp: LDO_REG8 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc1v8_dvp";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc2v8_dvp: LDO_REG9 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+				regulator-name = "vcc2v8_dvp";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			dcdc_boost: BOOST {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <4700000>;
+				regulator-max-microvolt = <5400000>;
+				regulator-name = "boost";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			otg_switch: OTG_SWITCH {
+				regulator-name = "otg_switch";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+		};
+	};
+
+	vdd_cpu: regulator@40 {
+		compatible = "fcs,fan53555";
+		reg = <0x40>;
+		fcs,suspend-voltage-selector = <1>;
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <712500>;
+		regulator-max-microvolt = <1390000>;
+		regulator-init-microvolt = <900000>;
+		regulator-name = "vdd_cpu";
+		regulator-ramp-delay = <2300>;
+		vin-supply = <&vcc_sys>;
+		regulator-state-mem {
+			regulator-off-in-suspend;
+		};
+	};
+};
+
+&i2c1 {
+	/* Unknown/unused device at 0x3c */
+	status = "disabled";
+};
+
+&i2c5 {
+	pinctrl-0 = <&i2c5m1_xfer>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&i2s0_8ch {
+	status = "okay";
+};
+
+&i2s1_8ch {
+	pinctrl-0 = <&i2s1m0_sclktx
+		     &i2s1m0_lrcktx
+		     &i2s1m0_sdi0
+		     &i2s1m0_sdo0>;
+	pinctrl-names = "default";
+	rockchip,trcm-sync-tx-only;
+	status = "okay";
+};
+
+&pinctrl {
+	audio-amplifier {
+		spk_amp_enable_h: spk-amp-enable-h {
+			rockchip,pins =
+				<4 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	gpio-btns {
+		btn_pins_ctrl: btn-pins-ctrl {
+			rockchip,pins =
+				<3 RK_PA1 RK_FUNC_GPIO &pcfg_pull_up>,
+				<3 RK_PA2 RK_FUNC_GPIO &pcfg_pull_up>,
+				<3 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>,
+				<3 RK_PA4 RK_FUNC_GPIO &pcfg_pull_up>,
+				<3 RK_PA5 RK_FUNC_GPIO &pcfg_pull_up>,
+				<3 RK_PA6 RK_FUNC_GPIO &pcfg_pull_up>,
+				<3 RK_PB1 RK_FUNC_GPIO &pcfg_pull_up>,
+				<3 RK_PB2 RK_FUNC_GPIO &pcfg_pull_up>,
+				<3 RK_PB3 RK_FUNC_GPIO &pcfg_pull_up>,
+				<3 RK_PB4 RK_FUNC_GPIO &pcfg_pull_up>,
+				<3 RK_PB5 RK_FUNC_GPIO &pcfg_pull_up>,
+				<3 RK_PB6 RK_FUNC_GPIO &pcfg_pull_up>,
+				<3 RK_PC0 RK_FUNC_GPIO &pcfg_pull_up>,
+				<3 RK_PC1 RK_FUNC_GPIO &pcfg_pull_up>,
+				<3 RK_PC2 RK_FUNC_GPIO &pcfg_pull_up>,
+				<3 RK_PC3 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+
+		btn_pins_vol: btn-pins-vol {
+			rockchip,pins =
+			<3 RK_PA7 RK_FUNC_GPIO &pcfg_pull_up>,
+			<3 RK_PB0 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	gpio-led {
+		led_pins: led-pins {
+			rockchip,pins =
+				<0 RK_PC5 RK_FUNC_GPIO &pcfg_pull_none>,
+				<0 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>,
+				<0 RK_PC7 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	joy-mux {
+		joy_mux_en: joy-mux-en {
+			rockchip,pins =
+				<0 RK_PB5 RK_FUNC_GPIO &pcfg_output_low>;
+		};
+	};
+
+	pmic {
+		pmic_int_l: pmic-int-l {
+			rockchip,pins =
+				<0 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	sdio-pwrseq {
+		wifi_enable_h: wifi-enable-h {
+			rockchip,pins =
+				<4 RK_PA2 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	vcc3v3-lcd {
+		vcc_lcd_h: vcc-lcd-h {
+			rockchip,pins =
+				<0 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	vcc-wifi {
+		vcc_wifi_h: vcc-wifi-h {
+			rockchip,pins =
+				<0 RK_PA0 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+};
+
+&pmu_io_domains {
+	status = "okay";
+	pmuio1-supply = <&vcc3v3_pmu>;
+	pmuio2-supply = <&vcc3v3_pmu>;
+	vccio1-supply = <&vccio_acodec>;
+	vccio3-supply = <&vccio_sd>;
+	vccio4-supply = <&vcc_1v8>;
+	vccio5-supply = <&vcc_3v3>;
+	vccio6-supply = <&vcc1v8_dvp>;
+	vccio7-supply = <&vcc_3v3>;
+};
+
+&pwm5 {
+	status = "okay";
+};
+
+&saradc {
+	vref-supply = <&vcc_1v8>;
+	status = "okay";
+};
+
+&sdmmc0 {
+	bus-width = <4>;
+	cap-sd-highspeed;
+	cd-gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_LOW>;
+	disable-wp;
+	pinctrl-0 = <&sdmmc0_bus4 &sdmmc0_clk &sdmmc0_cmd &sdmmc0_det>;
+	pinctrl-names = "default";
+	sd-uhs-sdr104;
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&vccio_sd>;
+	status = "okay";
+};
+
+&sdmmc1 {
+	bus-width = <4>;
+	cap-sd-highspeed;
+	cd-gpios = <&gpio2 RK_PB2 GPIO_ACTIVE_LOW>;
+	disable-wp;
+	pinctrl-0 = <&sdmmc1_bus4 &sdmmc1_cmd &sdmmc1_clk &sdmmc1_det>;
+	pinctrl-names = "default";
+	sd-uhs-sdr104;
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&vcc1v8_dvp>;
+	status = "okay";
+};
+
+&sdmmc2 {
+	bus-width = <4>;
+	cap-sd-highspeed;
+	cap-sdio-irq;
+	keep-power-in-suspend;
+	mmc-pwrseq = <&sdio_pwrseq>;
+	non-removable;
+	pinctrl-0 = <&sdmmc2m0_bus4 &sdmmc2m0_cmd &sdmmc2m0_clk>;
+	pinctrl-names = "default";
+	vmmc-supply = <&vcc_wifi>;
+	vqmmc-supply = <&vcca1v8_pmu>;
+	status = "okay";
+};
+
+&tsadc {
+	rockchip,hw-tshut-mode = <1>;
+	rockchip,hw-tshut-polarity = <0>;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-0 = <&uart1m1_xfer &uart1m1_ctsn &uart1m1_rtsn>;
+	pinctrl-names = "default";
+	uart-has-rtscts;
+	status = "okay";
+
+	bluetooth {
+		compatible = "realtek,rtl8821cs-bt";
+		device-wake-gpios = <&gpio4 4 GPIO_ACTIVE_HIGH>;
+		enable-gpios = <&gpio4 3 GPIO_ACTIVE_HIGH>;
+		host-wake-gpios = <&gpio4 5 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&uart2 {
+	status = "okay";
+};
+
+/*
+ * Lack the schematics to verify, but port works as a peripheral
+ * (and not a host or OTG port).
+ */
+&usb_host0_xhci {
+	dr_mode = "peripheral";
+	phys = <&usb2phy0_otg>;
+	phy-names = "usb2-phy";
+	status = "okay";
+};
+
+&usb_host1_ehci {
+	status = "okay";
+};
+
+&usb_host1_ohci {
+	status = "okay";
+};
+
+&usb_host1_xhci {
+	phy-names = "usb2-phy", "usb3-phy";
+	phys = <&usb2phy1_host>, <&combphy1 PHY_TYPE_USB3>;
+	status = "okay";
+};
+
+&usb2phy0 {
+	status = "okay";
+};
+
+&usb2phy0_otg {
+	status = "okay";
+};
+
+&usb2phy1 {
+	status = "okay";
+};
+
+&usb2phy1_host {
+	status = "okay";
+};
+
+&vop {
+	assigned-clocks = <&cru DCLK_VOP0>, <&cru DCLK_VOP1>;
+	assigned-clock-parents = <&pmucru PLL_HPLL>, <&cru PLL_VPLL>;
+	status = "okay";
+};
+
+&vop_mmu {
+	status = "okay";
+};
+
+&vp0 {
+	vp0_out_hdmi: endpoint@ROCKCHIP_VOP2_EP_HDMI0 {
+		reg = <ROCKCHIP_VOP2_EP_HDMI0>;
+		remote-endpoint = <&hdmi_in_vp0>;
+	};
+};
diff --git a/arch/arm64/boot/dts/rockchip/rk3566-pinenote-v1.1.dts b/arch/arm64/boot/dts/rockchip/rk3566-pinenote-v1.1.dts
new file mode 100644
index 000000000000..5b0b7ebf9fee
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3566-pinenote-v1.1.dts
@@ -0,0 +1,18 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+/dts-v1/;
+
+#include "rk3566-pinenote.dtsi"
+
+/ {
+	model = "Pine64 PineNote v1.1";
+	compatible = "pine64,pinenote-v1.1", "pine64,pinenote", "rockchip,rk3566";
+};
+
+&pmu_io_domains {
+	vccio7-supply = <&vcc_1v8>;
+};
+
+&spk_amp {
+	VCC-supply = <&dcdc_boost>;
+};
diff --git a/arch/arm64/boot/dts/rockchip/rk3566-pinenote-v1.2.dts b/arch/arm64/boot/dts/rockchip/rk3566-pinenote-v1.2.dts
new file mode 100644
index 000000000000..6bbc4c675d64
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3566-pinenote-v1.2.dts
@@ -0,0 +1,18 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+/dts-v1/;
+
+#include "rk3566-pinenote.dtsi"
+
+/ {
+	model = "Pine64 PineNote v1.2";
+	compatible = "pine64,pinenote-v1.2", "pine64,pinenote", "rockchip,rk3566";
+};
+
+&pmu_io_domains {
+	vccio7-supply = <&vcc_3v3>;
+};
+
+&spk_amp {
+	VCC-supply = <&vcc_bat>;
+};
diff --git a/arch/arm64/boot/dts/rockchip/rk3566-pinenote.dtsi b/arch/arm64/boot/dts/rockchip/rk3566-pinenote.dtsi
new file mode 100644
index 000000000000..0d45868132b9
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3566-pinenote.dtsi
@@ -0,0 +1,719 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/gpio-keys.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/rockchip.h>
+
+#include "rk3566.dtsi"
+
+/ {
+	aliases {
+		mmc0 = &sdhci;
+	};
+
+	chosen {
+		stdout-path = "serial2:1500000n8";
+	};
+
+	adc-keys {
+		compatible = "adc-keys";
+		io-channels = <&saradc 0>;
+		io-channel-names = "buttons";
+		keyup-threshold-microvolt = <1750000>;
+
+		recovery {
+			label = "recovery";
+			linux,code = <KEY_VENDOR>;
+			press-threshold-microvolt = <0>;
+		};
+	};
+
+	spk_amp: audio-amplifier {
+		compatible = "simple-audio-amplifier";
+		enable-gpios = <&gpio3 RK_PC4 GPIO_ACTIVE_HIGH>;
+		pinctrl-0 = <&spk_amp_enable_h>;
+		pinctrl-names = "default";
+		sound-name-prefix = "Speaker Amp";
+	};
+
+	dmic_codec: dmic-codec {
+		compatible = "dmic-codec";
+		num-channels = <6>;
+		#sound-dai-cells = <0>;
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-0 = <&hall_int_l>;
+		pinctrl-names = "default";
+
+		switch-cover {
+			label = "cover";
+			gpios = <&gpio0 RK_PC7 GPIO_ACTIVE_LOW>;
+			linux,input-type = <EV_SW>;
+			linux,code = <SW_MACHINE_COVER>;
+			linux,can-disable;
+			wakeup-event-action = <EV_ACT_DEASSERTED>;
+			wakeup-source;
+		};
+	};
+
+	gpio-leds {
+		compatible = "gpio-leds";
+		pinctrl-0 = <&led_pin>;
+		pinctrl-names = "default";
+
+		led-0 {
+			color = <LED_COLOR_ID_WHITE>;
+			function = LED_FUNCTION_CHARGING;
+			gpios = <&gpio3 RK_PC5 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	sdio_pwrseq: sdio-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		clocks = <&rk817 1>;
+		clock-names = "ext_clock";
+		pinctrl-0 = <&wifi_enable_h>;
+		pinctrl-names = "default";
+		reset-gpios = <&gpio0 RK_PC6 GPIO_ACTIVE_LOW>;
+	};
+
+	sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "PineNote";
+		simple-audio-card,aux-devs = <&spk_amp>;
+		simple-audio-card,widgets = "Headphone", "Headphones",
+					    "Speaker", "Internal Speakers";
+		simple-audio-card,routing = "Headphones", "HPOL",
+					    "Headphones", "HPOR",
+					    "Internal Speakers", "Speaker Amp OUTL",
+					    "Internal Speakers", "Speaker Amp OUTR",
+					    "Speaker Amp INL", "HPOL",
+					    "Speaker Amp INR", "HPOR";
+		simple-audio-card,pin-switches = "Internal Speakers";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		simple-audio-card,dai-link@0 {
+			reg = <0>;
+			bitclock-master = <&link0_cpu>;
+			format = "i2s";
+			frame-master = <&link0_cpu>;
+			mclk-fs = <256>;
+
+			link0_cpu: cpu {
+				sound-dai = <&i2s1_8ch>;
+			};
+
+			link0_codec: codec {
+				sound-dai = <&rk817>;
+			};
+		};
+
+		simple-audio-card,dai-link@1 {
+			reg = <1>;
+			bitclock-master = <&link1_cpu>;
+			format = "pdm";
+			frame-master = <&link1_cpu>;
+
+			link1_cpu: cpu {
+				sound-dai = <&pdm>;
+			};
+
+			link1_codec: codec {
+				sound-dai = <&dmic_codec>;
+			};
+		};
+	};
+
+	vbat_4g: vbat-4g {
+		compatible = "regulator-fixed";
+		regulator-name = "vbat_4g";
+		regulator-min-microvolt = <3800000>;
+		regulator-max-microvolt = <3800000>;
+		/* powered by vcc_bat, enabled by vbat_4g_en */
+		vin-supply = <&vbat_4g_en>;
+	};
+
+	vcc_1v8: vcc-1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_1v8";
+		regulator-always-on;
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		/* powered by vcc_sys, enabled by vcc_1v8_en */
+		vin-supply = <&vcc_1v8_en>;
+	};
+
+	vcc_bat: vcc-bat {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_bat";
+		regulator-always-on;
+		regulator-min-microvolt = <3800000>;
+		regulator-max-microvolt = <3800000>;
+	};
+
+	vcc_hall_3v3: vcc-hall-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_hall_3v3";
+		regulator-always-on;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc_sys>;
+	};
+
+	vcc_sys: vcc-sys {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_sys";
+		regulator-always-on;
+		regulator-min-microvolt = <3800000>;
+		regulator-max-microvolt = <3800000>;
+		vin-supply = <&vcc_bat>;
+	};
+
+	vcc_wl: vcc-wl {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio0 RK_PA0 GPIO_ACTIVE_HIGH>;
+		pinctrl-0 = <&vcc_wl_pin>;
+		pinctrl-names = "default";
+		regulator-name = "vcc_wl";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc_bat>;
+	};
+
+	vdda_0v9: vdda-0v9 {
+		compatible = "regulator-fixed";
+		regulator-name = "vdda_0v9";
+		regulator-always-on;
+		regulator-min-microvolt = <900000>;
+		regulator-max-microvolt = <900000>;
+		/* powered by vcc_sys, enabled by vcc_1v8_en */
+		vin-supply = <&vcc_1v8_en>;
+	};
+};
+
+&cpu0 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&cpu1 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&cpu2 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&cpu3 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&i2c0 {
+	status = "okay";
+
+	vdd_cpu: regulator@1c {
+		compatible = "tcs,tcs4525";
+		reg = <0x1c>;
+		fcs,suspend-voltage-selector = <0>;
+		regulator-name = "vdd_cpu";
+		regulator-min-microvolt = <712500>;
+		regulator-max-microvolt = <1390000>;
+		regulator-ramp-delay = <2300>;
+		regulator-always-on;
+		vin-supply = <&vcc_sys>;
+
+		regulator-state-mem {
+			regulator-on-in-suspend;
+		};
+	};
+
+	rk817: pmic@20 {
+		compatible = "rockchip,rk817";
+		reg = <0x20>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <RK_PA3 IRQ_TYPE_LEVEL_LOW>;
+		assigned-clocks = <&cru I2S1_MCLKOUT_TX>;
+		assigned-clock-parents = <&cru CLK_I2S1_8CH_TX>;
+		clocks = <&cru I2S1_MCLKOUT_TX>;
+		clock-names = "mclk";
+		#clock-cells = <1>;
+		pinctrl-0 = <&i2s1m0_mclk>, <&pmic_int_l>, <&pmic_sleep>;
+		pinctrl-names = "default";
+		rockchip,system-power-controller;
+		#sound-dai-cells = <0>;
+		wakeup-source;
+
+		vcc1-supply = <&vcc_sys>;
+		vcc2-supply = <&vcc_sys>;
+		vcc3-supply = <&vcc_sys>;
+		vcc4-supply = <&vcc_sys>;
+		vcc5-supply = <&vcc_sys>;
+		vcc6-supply = <&vcc_sys>;
+		vcc7-supply = <&vcc_sys>;
+		vcc8-supply = <&vcc_sys>;
+		vcc9-supply = <&dcdc_boost>;
+
+		regulators {
+			vdd_logic: DCDC_REG1 {
+				regulator-name = "vdd_logic";
+				regulator-always-on;
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-init-microvolt = <900000>;
+				regulator-ramp-delay = <6001>;
+				regulator-initial-mode = <0x2>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+					regulator-suspend-microvolt = <900000>;
+				};
+			};
+
+			vdd_gpu_npu: DCDC_REG2 {
+				regulator-name = "vdd_gpu_npu";
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-init-microvolt = <900000>;
+				regulator-ramp-delay = <6001>;
+				regulator-initial-mode = <0x2>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_ddr: DCDC_REG3 {
+				regulator-name = "vcc_ddr";
+				regulator-always-on;
+				regulator-initial-mode = <0x2>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vcc_3v3: DCDC_REG4 {
+				regulator-name = "vcc_3v3";
+				regulator-always-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-initial-mode = <0x2>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcca_1v8_pmu: LDO_REG1 {
+				regulator-name = "vcca_1v8_pmu";
+				regulator-always-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			/* unused */
+			vdda_0v9_ldo: LDO_REG2 {
+				regulator-name = "vdda_0v9_ldo";
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <900000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdda_0v9_pmu: LDO_REG3 {
+				regulator-name = "vdda_0v9_pmu";
+				regulator-always-on;
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <900000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vccio_acodec: LDO_REG4 {
+				regulator-name = "vccio_acodec";
+				regulator-always-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			/* unused */
+			vccio_sd: LDO_REG5 {
+				regulator-name = "vccio_sd";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_3v3_pmu: LDO_REG6 {
+				regulator-name = "vcc_3v3_pmu";
+				regulator-always-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vcc_1v8_en: LDO_REG7 {
+				regulator-name = "vcc_1v8_en";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vbat_4g_en: LDO_REG8 {
+				regulator-name = "vbat_4g_en";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			sleep_sta_ctl: LDO_REG9 {
+				regulator-name = "sleep_sta_ctl";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			dcdc_boost: BOOST {
+				regulator-name = "boost";
+				regulator-min-microvolt = <5000000>;
+				regulator-max-microvolt = <5000000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			otg_switch: OTG_SWITCH {
+				regulator-name = "otg_switch";
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+		};
+	};
+};
+
+&i2c1 {
+	status = "okay";
+
+	digitizer@9 {
+		compatible = "wacom,w9013", "hid-over-i2c";
+		reg = <0x09>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <RK_PB6 IRQ_TYPE_LEVEL_LOW>;
+		hid-descr-addr = <0x1>;
+		pinctrl-0 = <&pen_fwe>, <&pen_irq_l>, <&pen_rst_l>;
+		pinctrl-names = "default";
+		vdd-supply = <&vcc_3v3_pmu>;
+	};
+};
+
+&i2c3 {
+	pinctrl-0 = <&i2c3m1_xfer>;
+	status = "okay";
+
+	led-controller@36 {
+		compatible = "ti,lm3630a";
+		reg = <0x36>;
+		enable-gpios = <&gpio0 RK_PB7 GPIO_ACTIVE_HIGH>;
+		pinctrl-0 = <&backlight_hwen_h>;
+		pinctrl-names = "default";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		led@0 {
+			reg = <0>;
+			label = "backlight_cool";
+			default-brightness = <0>;
+		};
+
+		led@1 {
+			reg = <1>;
+			label = "backlight_warm";
+			default-brightness = <0>;
+		};
+	};
+
+	wusb3801: tcpc@60 {
+		compatible = "willsemi,wusb3801";
+		reg = <0x60>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <RK_PA4 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-0 = <&tcpc_int_l>;
+		pinctrl-names = "default";
+
+		connector {
+			compatible = "usb-c-connector";
+			label = "USB-C";
+			vbus-supply = <&otg_switch>;
+			power-role = "dual";
+			try-power-role = "sink";
+			data-role = "dual";
+			typec-power-opmode = "default";
+			pd-disable;
+
+			ports {
+				#address-cells = <0x1>;
+				#size-cells = <0x0>;
+
+				port@0 {
+					reg = <0x0>;
+
+					typec_hs_usb2phy0: endpoint {
+						remote-endpoint = <&usb2phy0_typec_hs>;
+					};
+				};
+			};
+		};
+	};
+};
+
+&i2c5 {
+	status = "okay";
+
+	accelerometer@18 {
+		compatible = "silan,sc7a20";
+		reg = <0x18>;
+		interrupt-parent = <&gpio3>;
+		interrupts = <RK_PB2 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-0 = <&accelerometer_int_l>;
+		pinctrl-names = "default";
+		st,drdy-int-pin = <1>;
+		vdd-supply = <&vcc_3v3>;
+		vddio-supply = <&vcc_3v3>;
+	};
+};
+
+&i2s1_8ch {
+	pinctrl-0 = <&i2s1m0_lrcktx>, <&i2s1m0_sclktx>, <&i2s1m0_sdi0>, <&i2s1m0_sdo0>;
+	rockchip,trcm-sync-tx-only;
+	status = "okay";
+};
+
+&pdm {
+	pinctrl-0 = <&pdmm0_clk1>, <&pdmm0_sdi1>, <&pdmm0_sdi2>;
+	/* microphones are on channels 1 and 2 */
+	rockchip,path-map = <1>, <2>, <0>, <3>;
+	status = "okay";
+};
+
+&pinctrl {
+	accelerometer {
+		accelerometer_int_l: accelerometer-int-l {
+			rockchip,pins = <3 RK_PB2 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	audio-amplifier {
+		spk_amp_enable_h: spk-amp-enable-h {
+			rockchip,pins = <3 RK_PC4 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	backlight {
+		backlight_hwen_h: backlight-hwen-h {
+			rockchip,pins = <0 RK_PB7 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	bt {
+		bt_enable_h: bt-enable-h {
+			rockchip,pins = <0 RK_PC4 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		bt_host_wake_l: bt-host-wake-l {
+			rockchip,pins = <0 RK_PC3 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+
+		bt_wake_h: bt-wake-h {
+			rockchip,pins = <0 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	led {
+		led_pin: led-pin {
+			rockchip,pins = <3 RK_PC5 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	hall {
+		hall_int_l: hall-int-l {
+			rockchip,pins = <0 RK_PC7 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	pen {
+		pen_fwe: pen-fwe {
+			rockchip,pins = <3 RK_PB7 RK_FUNC_GPIO &pcfg_pull_down>;
+		};
+
+		pen_irq_l: pen-irq-l {
+			rockchip,pins = <0 RK_PB6 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		pen_rst_l: pen-rst-l {
+			rockchip,pins = <0 RK_PC1 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	pmic {
+		pmic_int_l: pmic-int-l {
+			rockchip,pins = <0 RK_PA3 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		pmic_sleep: pmic-sleep {
+			rockchip,pins = <0 RK_PA2 1 &pcfg_pull_none>;
+		};
+	};
+
+	sdio-pwrseq {
+		wifi_enable_h: wifi-enable-h {
+			rockchip,pins = <0 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	tcpc {
+		tcpc_int_l: tcpc-int-l {
+			rockchip,pins = <0 RK_PA4 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	vcc-wl {
+		vcc_wl_pin: vcc-wl-pin {
+			rockchip,pins = <0 RK_PA0 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	wifi {
+		wifi_host_wake_l: wifi-host-wake-l {
+			rockchip,pins = <0 RK_PC5 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+};
+
+&pmu_io_domains {
+	pmuio1-supply = <&vcc_3v3_pmu>;
+	pmuio2-supply = <&vcc_3v3_pmu>;
+	vccio1-supply = <&vccio_acodec>;
+	vccio2-supply = <&vcc_1v8>;
+	vccio3-supply = <&vcc_3v3>;
+	vccio4-supply = <&vcca_1v8_pmu>;
+	vccio5-supply = <&vcc_3v3>;
+	vccio6-supply = <&vcc_3v3>;
+	status = "okay";
+};
+
+&saradc {
+	vref-supply = <&vcc_1v8>;
+	status = "okay";
+};
+
+&sdhci {
+	bus-width = <8>;
+	mmc-hs200-1_8v;
+	non-removable;
+	pinctrl-0 = <&emmc_bus8>, <&emmc_clk>, <&emmc_cmd>, <&emmc_datastrobe>, <&emmc_rstnout>;
+	pinctrl-names = "default";
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&vcc_1v8>;
+	status = "okay";
+};
+
+&sdmmc1 {
+	bus-width = <4>;
+	cap-sd-highspeed;
+	cap-sdio-irq;
+	keep-power-in-suspend;
+	mmc-pwrseq = <&sdio_pwrseq>;
+	non-removable;
+	pinctrl-0 = <&sdmmc1_bus4>, <&sdmmc1_clk>, <&sdmmc1_cmd>;
+	pinctrl-names = "default";
+	sd-uhs-sdr104;
+	vmmc-supply = <&vcc_wl>;
+	vqmmc-supply = <&vcca_1v8_pmu>;
+	status = "okay";
+};
+
+&tsadc {
+	/* tshut mode 0:CRU 1:GPIO */
+	rockchip,hw-tshut-mode = <1>;
+	/* tshut polarity 0:LOW 1:HIGH */
+	rockchip,hw-tshut-polarity = <0>;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-0 = <&uart1m0_ctsn>, <&uart1m0_rtsn>, <&uart1m0_xfer>;
+	pinctrl-names = "default";
+	uart-has-rtscts;
+	status = "okay";
+
+	bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		clocks = <&rk817 1>;
+		clock-names = "lpo";
+		device-wake-gpios = <&gpio0 RK_PC2 GPIO_ACTIVE_HIGH>;
+		host-wake-gpios = <&gpio0 RK_PC3 GPIO_ACTIVE_HIGH>;
+		reset-gpios = <&gpio0 RK_PC4 GPIO_ACTIVE_LOW>;
+		pinctrl-0 = <&bt_enable_h>, <&bt_host_wake_l>, <&bt_wake_h>;
+		pinctrl-names = "default";
+		vbat-supply = <&vcc_wl>;
+		vddio-supply = <&vcca_1v8_pmu>;
+	};
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&usb_host0_xhci {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&usb2phy0 {
+	status = "okay";
+};
+
+&usb2phy0_otg {
+	status = "okay";
+
+	port {
+		usb2phy0_typec_hs: endpoint {
+			remote-endpoint = <&typec_hs_usb2phy0>;
+		};
+	};
+};
diff --git a/arch/arm64/boot/dts/rockchip/rk3566-quartz64-a.dts b/arch/arm64/boot/dts/rockchip/rk3566-quartz64-a.dts
index 4d4b2a301b1a..a05460b92415 100644
--- a/arch/arm64/boot/dts/rockchip/rk3566-quartz64-a.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3566-quartz64-a.dts
@@ -4,6 +4,7 @@
 
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/pinctrl/rockchip.h>
+#include <dt-bindings/soc/rockchip,vop2.h>
 #include "rk3566.dtsi"
 
 / {
@@ -32,9 +33,22 @@
 		gpios = <&gpio0 RK_PD5 GPIO_ACTIVE_HIGH>;
 		gpio-fan,speed-map = <0    0
 				      4500 1>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&fan_en_h>;
 		#cooling-cells = <2>;
 	};
 
+	hdmi-con {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con_in: endpoint {
+				remote-endpoint = <&hdmi_out_con>;
+			};
+		};
+	};
+
 	leds {
 		compatible = "gpio-leds";
 
@@ -73,6 +87,17 @@
 		};
 	};
 
+	sdio_pwrseq: sdio-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		clocks = <&rk817 1>;
+		clock-names = "ext_clock";
+		pinctrl-names = "default";
+		pinctrl-0 = <&wifi_enable_h>;
+		post-power-on-delay-ms = <100>;
+		power-off-delay-us = <5000000>;
+		reset-gpios = <&gpio2 RK_PC2 GPIO_ACTIVE_LOW>;
+	};
+
 	spdif_dit: spdif-dit {
 		compatible = "linux,spdif-dit";
 		#sound-dai-cells = <0>;
@@ -114,6 +139,18 @@
 		vin-supply = <&vcc12v_dcin>;
 	};
 
+	vcc3v3_pcie_p: vcc3v3-pcie-p-regulator {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio0 RK_PC6 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pcie_enable_h>;
+		regulator-name = "vcc3v3_pcie_p";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc_3v3>;
+	};
+
 	vcc5v0_usb: vcc5v0_usb {
 		compatible = "regulator-fixed";
 		regulator-name = "vcc5v0_usb";
@@ -124,9 +161,34 @@
 		vin-supply = <&vcc12v_dcin>;
 	};
 
+	/* all four ports are controlled by one gpio
+	 * the host ports are sourced from vcc5v0_usb
+	 * the otg port is sourced from vcc5v0_midu
+	 */
+	vcc5v0_usb20_host: vcc5v0_usb20_host {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio4 RK_PB5 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vcc5v0_usb20_host_en>;
+		regulator-name = "vcc5v0_usb20_host";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc5v0_usb>;
+	};
+
+	vcc5v0_usb20_otg: vcc5v0_usb20_otg {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio4 RK_PB5 GPIO_ACTIVE_HIGH>;
+		regulator-name = "vcc5v0_usb20_otg";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&dcdc_boost>;
+	};
+
 	vcc3v3_sd: vcc3v3_sd {
 		compatible = "regulator-fixed";
-		enable-active-low;
 		gpio = <&gpio0 RK_PA5 GPIO_ACTIVE_LOW>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&vcc_sd_h>;
@@ -147,6 +209,25 @@
 		regulator-max-microvolt = <4400000>;
 		vin-supply = <&vbus>;
 	};
+
+	/* sourced from vcc_sys, sdio module operates internally at 3.3v */
+	vcc_wl: vcc_wl {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_wl";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc_sys>;
+	};
+};
+
+&combphy1 {
+	status = "okay";
+};
+
+&combphy2 {
+	status = "okay";
 };
 
 &cpu0 {
@@ -205,6 +286,33 @@
 	status = "okay";
 };
 
+&gpu {
+	mali-supply = <&vdd_gpu>;
+	status = "okay";
+};
+
+&hdmi {
+	avdd-0v9-supply = <&vdda_0v9>;
+	avdd-1v8-supply = <&vcc_1v8>;
+	status = "okay";
+};
+
+&hdmi_in {
+	hdmi_in_vp0: endpoint {
+		remote-endpoint = <&vp0_out_hdmi>;
+	};
+};
+
+&hdmi_out {
+	hdmi_out_con: endpoint {
+		remote-endpoint = <&hdmi_con_in>;
+	};
+};
+
+&hdmi_sound {
+	status = "okay";
+};
+
 &i2c0 {
 	status = "okay";
 
@@ -285,8 +393,6 @@
 			vcc_ddr: DCDC_REG3 {
 				regulator-always-on;
 				regulator-boot-on;
-				regulator-min-microvolt = <1100000>;
-				regulator-max-microvolt = <1100000>;
 				regulator-initial-mode = <0x2>;
 				regulator-name = "vcc_ddr";
 				regulator-state-mem {
@@ -429,6 +535,18 @@
 	};
 };
 
+/* i2c3 is exposed on con40
+ * pin 3 - i2c3_sda_m0, pullup to vcc_3v3
+ * pin 5 - i2c3_scl_m0, pullup to vcc_3v3
+ */
+&i2c3 {
+	status = "okay";
+};
+
+&i2s0_8ch {
+	status = "okay";
+};
+
 &i2s1_8ch {
 	pinctrl-names = "default";
 	pinctrl-0 = <&i2s1m0_sclktx
@@ -446,6 +564,14 @@
 	};
 };
 
+&pcie2x1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie_reset_h>;
+	reset-gpios = <&gpio1 RK_PB2 GPIO_ACTIVE_HIGH>;
+	vpcie3v3-supply = <&vcc3v3_pcie_p>;
+	status = "okay";
+};
+
 &pinctrl {
 	bt {
 		bt_enable_h: bt-enable-h {
@@ -461,6 +587,12 @@
 		};
 	};
 
+	fan {
+		fan_en_h: fan-en-h {
+			rockchip,pins = <0 RK_PD5 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
 	leds {
 		work_led_enable_h: work-led-enable-h {
 			rockchip,pins = <0 RK_PD3 RK_FUNC_GPIO &pcfg_pull_none>;
@@ -471,12 +603,34 @@
 		};
 	};
 
+	pcie {
+		pcie_enable_h: pcie-enable-h {
+			rockchip,pins = <0 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		pcie_reset_h: pcie-reset-h {
+			rockchip,pins = <1 RK_PB2 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
 	pmic {
 		pmic_int_l: pmic-int-l {
 			rockchip,pins = <0 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>;
 		};
 	};
 
+	usb2 {
+		vcc5v0_usb20_host_en: vcc5v0-usb20-host-en {
+			rockchip,pins = <4 RK_PB5 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	sdio-pwrseq {
+		wifi_enable_h: wifi-enable-h {
+			rockchip,pins = <2 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
 	vcc_sd {
 		vcc_sd_h: vcc-sd-h {
 			rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>;
@@ -484,6 +638,19 @@
 	};
 };
 
+&pmu_io_domains {
+	pmuio1-supply = <&vcc3v3_pmu>;
+	pmuio2-supply = <&vcc3v3_pmu>;
+	vccio1-supply = <&vccio_acodec>;
+	vccio2-supply = <&vcc_1v8>;
+	vccio3-supply = <&vccio_sd>;
+	vccio4-supply = <&vcc_1v8>;
+	vccio5-supply = <&vcc_3v3>;
+	vccio6-supply = <&vcc1v8_dvp>;
+	vccio7-supply = <&vcc_3v3>;
+	status = "okay";
+};
+
 &sdhci {
 	bus-width = <8>;
 	mmc-hs200-1_8v;
@@ -500,15 +667,59 @@
 	disable-wp;
 	pinctrl-names = "default";
 	pinctrl-0 = <&sdmmc0_bus4 &sdmmc0_clk &sdmmc0_cmd &sdmmc0_det>;
+	sd-uhs-sdr104;
 	vmmc-supply = <&vcc3v3_sd>;
 	vqmmc-supply = <&vccio_sd>;
 	status = "okay";
 };
 
+&sdmmc1 {
+	bus-width = <4>;
+	cap-sd-highspeed;
+	cap-sdio-irq;
+	keep-power-in-suspend;
+	mmc-pwrseq = <&sdio_pwrseq>;
+	non-removable;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc1_bus4 &sdmmc1_cmd &sdmmc1_clk>;
+	sd-uhs-sdr104;
+	vmmc-supply = <&vcc_wl>;
+	vqmmc-supply = <&vcc_1v8>;
+	status = "okay";
+};
+
+&sfc {
+	pinctrl-0 = <&fspi_pins>;
+	pinctrl-names = "default";
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "disabled";
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <24000000>;
+		spi-rx-bus-width = <4>;
+		spi-tx-bus-width = <1>;
+	};
+};
+
+/* spdif is exposed on con40 pin 18 */
 &spdif {
 	status = "okay";
 };
 
+/* spi1 is exposed on con40
+ * pin 11 - spi1_mosi_m1
+ * pin 13 - spi1_miso_m1
+ * pin 15 - spi1_clk_m1
+ * pin 17 - spi1_cs0_m1
+ */
+&spi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi1m1_cs0 &spi1m1_pins>;
+};
+
 &tsadc {
 	/* tshut mode 0:CRU 1:GPIO */
 	rockchip,hw-tshut-mode = <1>;
@@ -517,6 +728,10 @@
 	status = "okay";
 };
 
+/* uart0 is exposed on con40
+ * pin 12 - uart0_tx
+ * pin 14 - uart0_rx
+ */
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_xfer>;
@@ -533,8 +748,8 @@
 		compatible = "brcm,bcm43438-bt";
 		clocks = <&rk817 1>;
 		clock-names = "lpo";
-		device-wake-gpios = <&gpio2 RK_PC1 GPIO_ACTIVE_HIGH>;
-		host-wake-gpios = <&gpio2 RK_PC0 GPIO_ACTIVE_HIGH>;
+		device-wakeup-gpios = <&gpio2 RK_PC1 GPIO_ACTIVE_HIGH>;
+		host-wakeup-gpios = <&gpio2 RK_PC0 GPIO_ACTIVE_HIGH>;
 		shutdown-gpios = <&gpio2 RK_PB7 GPIO_ACTIVE_HIGH>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&bt_host_wake_l &bt_wake_l &bt_enable_h>;
@@ -543,6 +758,81 @@
 	};
 };
 
+/* uart2 is exposed on con40
+ * pin 8 - uart2_tx_m0_debug
+ * pin 10 - uart2_rx_m0_debug
+ */
 &uart2 {
 	status = "okay";
 };
+
+&usb_host0_ehci {
+	status = "okay";
+};
+
+&usb_host0_ohci {
+	status = "okay";
+};
+
+&usb_host1_ehci {
+	status = "okay";
+};
+
+&usb_host1_ohci {
+	status = "okay";
+};
+
+&usb_host0_xhci {
+	dr_mode = "host";
+	status = "okay";
+};
+
+/* usb3 controller is muxed with sata1 */
+&usb_host1_xhci {
+	status = "okay";
+};
+
+&usb2phy0 {
+	status = "okay";
+};
+
+&usb2phy0_host {
+	phy-supply = <&vcc5v0_usb20_host>;
+	status = "okay";
+};
+
+&usb2phy0_otg {
+	phy-supply = <&vcc5v0_usb20_otg>;
+	status = "okay";
+};
+
+&usb2phy1 {
+	status = "okay";
+};
+
+&usb2phy1_host {
+	phy-supply = <&vcc5v0_usb20_host>;
+	status = "okay";
+};
+
+&usb2phy1_otg {
+	phy-supply = <&vcc5v0_usb20_host>;
+	status = "okay";
+};
+
+&vop {
+	assigned-clocks = <&cru DCLK_VOP0>, <&cru DCLK_VOP1>;
+	assigned-clock-parents = <&pmucru PLL_HPLL>, <&cru PLL_VPLL>;
+	status = "okay";
+};
+
+&vop_mmu {
+	status = "okay";
+};
+
+&vp0 {
+	vp0_out_hdmi: endpoint@ROCKCHIP_VOP2_EP_HDMI0 {
+		reg = <ROCKCHIP_VOP2_EP_HDMI0>;
+		remote-endpoint = <&hdmi_in_vp0>;
+	};
+};
diff --git a/arch/arm64/boot/dts/rockchip/rk3566-quartz64-b.dts b/arch/arm64/boot/dts/rockchip/rk3566-quartz64-b.dts
new file mode 100644
index 000000000000..77b179cd20e7
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3566-quartz64-b.dts
@@ -0,0 +1,739 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/rockchip.h>
+#include <dt-bindings/soc/rockchip,vop2.h>
+#include "rk3566.dtsi"
+
+/ {
+	model = "Pine64 RK3566 Quartz64-B Board";
+	compatible = "pine64,quartz64-b", "rockchip,rk3566";
+
+	aliases {
+		ethernet0 = &gmac1;
+		mmc0 = &sdmmc0;
+		mmc1 = &sdhci;
+		mmc2 = &sdmmc1;
+	};
+
+	chosen: chosen {
+		stdout-path = "serial2:1500000n8";
+	};
+
+	gmac1_clkin: external-gmac1-clock {
+		compatible = "fixed-clock";
+		clock-frequency = <125000000>;
+		clock-output-names = "gmac1_clkin";
+		#clock-cells = <0>;
+	};
+
+	hdmi-con {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con_in: endpoint {
+				remote-endpoint = <&hdmi_out_con>;
+			};
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-user {
+			label = "user-led";
+			default-state = "on";
+			gpios = <&gpio0 RK_PA0 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+			pinctrl-names = "default";
+			pinctrl-0 = <&user_led_enable_h>;
+			retain-state-suspended;
+		};
+	};
+
+	sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,format = "i2s";
+		simple-audio-card,name = "Analog RK809";
+		simple-audio-card,mclk-fs = <256>;
+
+		simple-audio-card,cpu {
+			sound-dai = <&i2s1_8ch>;
+		};
+
+		simple-audio-card,codec {
+			sound-dai = <&rk809>;
+		};
+	};
+
+	sdio_pwrseq: sdio-pwrseq {
+		status = "okay";
+		compatible = "mmc-pwrseq-simple";
+		clocks = <&rk809 1>;
+		clock-names = "ext_clock";
+		pinctrl-names = "default";
+		pinctrl-0 = <&wifi_enable_h>;
+		reset-gpios = <&gpio0 RK_PC0 GPIO_ACTIVE_LOW>;
+		post-power-on-delay-ms = <100>;
+		power-off-delay-us = <5000000>;
+	};
+
+	vcc3v3_pcie_p: vcc3v3-pcie-p-regulator {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio0 RK_PA6 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pcie_enable_h>;
+		regulator-name = "vcc3v3_pcie_p";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc_3v3>;
+	};
+
+	vcc5v0_in: vcc5v0-in-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc5v0_in";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	vcc5v0_sys: vcc5v0-sys-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc5v0_sys";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc5v0_in>;
+	};
+
+	vcc3v3_sys: vcc3v3-sys-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3_sys";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		vin-supply = <&vcc5v0_sys>;
+	};
+
+	vcc5v0_usb30_host: vcc5v0-usb30-host-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc5v0_usb30_host";
+		enable-active-high;
+		gpio = <&gpio0 RK_PC5 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vcc5v0_usb30_host_en_h>;
+		regulator-always-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc5v0_sys>;
+	};
+
+	vcc5v0_usb_otg: vcc5v0-usb-otg-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc5v0_usb_otg";
+		enable-active-high;
+		gpio = <&gpio0 RK_PC6 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vcc5v0_usb_otg_en_h>;
+		regulator-always-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc5v0_sys>;
+	};
+};
+
+&combphy1 {
+	status = "okay";
+};
+
+&combphy2 {
+	status = "okay";
+};
+
+&cpu0 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&cpu1 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&cpu2 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&cpu3 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&gmac1 {
+	assigned-clocks = <&cru SCLK_GMAC1_RX_TX>, <&cru SCLK_GMAC1_RGMII_SPEED>, <&cru SCLK_GMAC1>;
+	assigned-clock-parents = <&cru SCLK_GMAC1_RGMII_SPEED>, <&cru SCLK_GMAC1>, <&gmac1_clkin>;
+	clock_in_out = "input";
+	phy-mode = "rgmii";
+	phy-supply = <&vcc_3v3>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&gmac1m1_miim
+		     &gmac1m1_tx_bus2
+		     &gmac1m1_rx_bus2
+		     &gmac1m1_rgmii_clk
+		     &gmac1m1_clkinout
+		     &gmac1m1_rgmii_bus>;
+	snps,reset-gpio = <&gpio3 RK_PC0 GPIO_ACTIVE_LOW>;
+	snps,reset-active-low;
+	/* Reset time is 20ms, 100ms for rtl8211f, also works well here */
+	snps,reset-delays-us = <0 20000 100000>;
+	tx_delay = <0x4f>;
+	rx_delay = <0x24>;
+	phy-handle = <&rgmii_phy1>;
+	status = "okay";
+};
+
+&gpu {
+	mali-supply = <&vdd_gpu>;
+	status = "okay";
+};
+
+&hdmi {
+	avdd-0v9-supply = <&vdda0v9_image>;
+	avdd-1v8-supply = <&vcca1v8_image>;
+	status = "okay";
+};
+
+&hdmi_in {
+	hdmi_in_vp0: endpoint {
+		remote-endpoint = <&vp0_out_hdmi>;
+	};
+};
+
+&hdmi_out {
+	hdmi_out_con: endpoint {
+		remote-endpoint = <&hdmi_con_in>;
+	};
+};
+
+&hdmi_sound {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	vdd_cpu: regulator@1c {
+		compatible = "tcs,tcs4525";
+		reg = <0x1c>;
+		fcs,suspend-voltage-selector = <1>;
+		regulator-name = "vdd_cpu";
+		regulator-min-microvolt = <800000>;
+		regulator-max-microvolt = <1150000>;
+		regulator-ramp-delay = <2300>;
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&vcc5v0_sys>;
+
+		regulator-state-mem {
+			regulator-off-in-suspend;
+		};
+	};
+
+	rk809: pmic@20 {
+		compatible = "rockchip,rk809";
+		reg = <0x20>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <RK_PA7 IRQ_TYPE_LEVEL_LOW>;
+		assigned-clocks = <&cru I2S1_MCLKOUT_TX>;
+		assigned-clock-parents = <&cru CLK_I2S1_8CH_TX>;
+		clock-names = "mclk";
+		clocks = <&cru I2S1_MCLKOUT_TX>;
+		clock-output-names = "rk808-clkout1", "rk808-clkout2";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_int>, <&i2s1m0_mclk>;
+		rockchip,system-power-controller;
+		#sound-dai-cells = <0>;
+		wakeup-source;
+		#clock-cells = <1>;
+
+		vcc1-supply = <&vcc3v3_sys>;
+		vcc2-supply = <&vcc3v3_sys>;
+		vcc3-supply = <&vcc3v3_sys>;
+		vcc4-supply = <&vcc3v3_sys>;
+		vcc5-supply = <&vcc3v3_sys>;
+		vcc6-supply = <&vcc3v3_sys>;
+		vcc7-supply = <&vcc3v3_sys>;
+		vcc8-supply = <&vcc3v3_sys>;
+		vcc9-supply = <&vcc3v3_sys>;
+
+		regulators {
+			vdd_log: DCDC_REG1 {
+				regulator-name = "vdd_log";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-init-microvolt = <900000>;
+				regulator-ramp-delay = <6001>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <900000>;
+				};
+			};
+
+			vdd_gpu: DCDC_REG2 {
+				regulator-name = "vdd_gpu";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-init-microvolt = <900000>;
+				regulator-ramp-delay = <6001>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+					regulator-suspend-microvolt = <900000>;
+				};
+			};
+
+			vcc_ddr: DCDC_REG3 {
+				regulator-name = "vcc_ddr";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-initial-mode = <0x2>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vdd_npu: DCDC_REG4 {
+				regulator-name = "vdd_npu";
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-initial-mode = <0x2>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_1v8: DCDC_REG5 {
+				regulator-name = "vcc_1v8";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vdda0v9_image: LDO_REG1 {
+				regulator-name = "vdda0v9_image";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <900000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <900000>;
+				};
+			};
+
+			vdda_0v9: LDO_REG2 {
+				regulator-name = "vdda_0v9";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <900000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <900000>;
+				};
+			};
+
+			vdda0v9_pmu: LDO_REG3 {
+				regulator-name = "vdda0v9_pmu";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <900000>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <900000>;
+				};
+			};
+
+			vccio_acodec: LDO_REG4 {
+				regulator-name = "vccio_acodec";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+
+				};
+			};
+
+			vccio_sd: LDO_REG5 {
+				regulator-name = "vccio_sd";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+				};
+			};
+
+			vcc3v3_pmu: LDO_REG6 {
+				regulator-name = "vcc3v3_pmu";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+				};
+			};
+
+			vcca_1v8: LDO_REG7 {
+				regulator-name = "vcca_1v8";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vcca1v8_pmu: LDO_REG8 {
+				regulator-name = "vcca1v8_pmu";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vcca1v8_image: LDO_REG9 {
+				regulator-name = "vcca1v8_image";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vcc_3v3: SWITCH_REG1 {
+				regulator-boot-on;
+				regulator-name = "vcc_3v3";
+			};
+
+			vcc3v3_sd: SWITCH_REG2 {
+				regulator-name = "vcc3v3_sd";
+			};
+		};
+	};
+};
+
+/* i2c2_m1 exposed on csi port, pulled up to vcc_3v3 */
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2m1_xfer>;
+	status = "okay";
+};
+
+/* i2c3_m1 exposed on dsi port, pulled up to vcc_3v3 */
+&i2c3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c3m1_xfer>;
+	status = "okay";
+};
+
+/*
+ * i2c4_m0 is exposed on PI40, pulled up to vcc_3v3
+ * pin 27 - i2c4_sda_m0
+ * pin 28 - i2c4_scl_m0
+ */
+&i2c4 {
+	status = "okay";
+};
+
+/*
+ * i2c5_m0 is exposed on PI40
+ * pin 29 - i2c5_scl_m0
+ * pin 31 - i2c5_sda_m0
+ */
+&i2c5 {
+	status = "disabled";
+};
+
+&i2s0_8ch {
+	status = "okay";
+};
+
+&i2s1_8ch {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2s1m0_sclktx
+		     &i2s1m0_lrcktx
+		     &i2s1m0_sdi0
+		     &i2s1m0_sdo0>;
+	rockchip,trcm-sync-tx-only;
+	status = "okay";
+};
+
+&mdio1 {
+	rgmii_phy1: ethernet-phy@1 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0x1>;
+	};
+};
+
+&pcie2x1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie_reset_h>;
+	reset-gpios = <&gpio1 RK_PB2 GPIO_ACTIVE_HIGH>;
+	vpcie3v3-supply = <&vcc3v3_pcie_p>;
+	status = "okay";
+};
+
+&pinctrl {
+	bt {
+		bt_enable_h: bt-enable-h {
+			rockchip,pins = <0 RK_PC1 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		bt_host_wake_l: bt-host-wake-l {
+			rockchip,pins = <0 RK_PB3 RK_FUNC_GPIO &pcfg_pull_down>;
+		};
+
+		bt_wake_l: bt-wake-l {
+			rockchip,pins = <0 RK_PB4 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	leds {
+		user_led_enable_h: user-led-enable-h {
+			rockchip,pins = <0 RK_PA0 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	pcie {
+		pcie_enable_h: pcie-enable-h {
+			rockchip,pins = <0 RK_PA6 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		pcie_reset_h: pcie-reset-h {
+			rockchip,pins = <1 RK_PB2 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	pmic {
+		pmic_int: pmic_int {
+			rockchip,pins =
+				<0 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	sdio-pwrseq {
+		wifi_enable_h: wifi-enable-h {
+			rockchip,pins = <0 RK_PC0 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	usb {
+		vcc5v0_usb30_host_en_h: vcc5v0-usb30-host-en_h {
+			rockchip,pins = <0 RK_PC5 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		vcc5v0_usb_otg_en_h: vcc5v0-usb-otg-en_h {
+			rockchip,pins = <0 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+};
+
+&pmu_io_domains {
+	status = "okay";
+	pmuio1-supply = <&vcc3v3_pmu>;
+	pmuio2-supply = <&vcca1v8_pmu>;
+	vccio1-supply = <&vccio_acodec>;
+	vccio2-supply = <&vcc_1v8>;
+	vccio3-supply = <&vccio_sd>;
+	vccio4-supply = <&vcca1v8_pmu>;
+	vccio5-supply = <&vcc_3v3>;
+	vccio6-supply = <&vcc_3v3>;
+	vccio7-supply = <&vcc_3v3>;
+};
+
+&saradc {
+	vref-supply = <&vcca_1v8>;
+	status = "okay";
+};
+
+&sdhci {
+	bus-width = <8>;
+	mmc-hs200-1_8v;
+	non-removable;
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&vcc_1v8>;
+	status = "okay";
+};
+
+&sdmmc0 {
+	bus-width = <4>;
+	cap-sd-highspeed;
+	cd-gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_LOW>;
+	disable-wp;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc0_bus4 &sdmmc0_clk &sdmmc0_cmd &sdmmc0_det>;
+	sd-uhs-sdr50;
+	vmmc-supply = <&vcc3v3_sd>;
+	vqmmc-supply = <&vccio_sd>;
+	status = "okay";
+};
+
+&sdmmc1 {
+	bus-width = <4>;
+	cap-sd-highspeed;
+	cap-sdio-irq;
+	keep-power-in-suspend;
+	mmc-pwrseq = <&sdio_pwrseq>;
+	non-removable;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc1_bus4 &sdmmc1_cmd &sdmmc1_clk>;
+	vmmc-supply = <&vcc3v3_sys>;
+	vqmmc-supply = <&vcca1v8_pmu>;
+	status = "okay";
+};
+
+&sfc {
+	pinctrl-0 = <&fspi_pins>;
+	pinctrl-names = "default";
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <24000000>;
+		spi-rx-bus-width = <4>;
+		spi-tx-bus-width = <1>;
+	};
+};
+
+&tsadc {
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1m0_xfer &uart1m0_ctsn &uart1m0_rtsn>;
+	status = "okay";
+	uart-has-rtscts;
+
+	bluetooth {
+		compatible = "brcm,bcm4345c5";
+		clocks = <&rk809 1>;
+		clock-names = "lpo";
+		device-wakeup-gpios = <&gpio0 RK_PB4 GPIO_ACTIVE_HIGH>;
+		host-wakeup-gpios = <&gpio0 RK_PB3 GPIO_ACTIVE_HIGH>;
+		shutdown-gpios = <&gpio0 RK_PC1 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&bt_host_wake_l &bt_wake_l &bt_enable_h>;
+		vbat-supply = <&vcc3v3_sys>;
+		vddio-supply = <&vcca1v8_pmu>;
+	};
+};
+
+/*
+ * uart2_m0 is exposed on PI40
+ * pin 8  - uart2_tx_m0
+ * pin 10 - uart2_rx_m0
+ */
+&uart2 {
+	status = "okay";
+};
+
+&usb2phy0_host {
+	phy-supply = <&vcc5v0_usb30_host>;
+	status = "okay";
+};
+
+&usb2phy0_otg {
+	phy-supply = <&vcc5v0_usb_otg>;
+	status = "okay";
+};
+
+&usb2phy1_otg {
+	phy-supply = <&vcc5v0_usb30_host>;
+	status = "okay";
+};
+
+&usb2phy0 {
+	status = "okay";
+};
+
+&usb2phy1 {
+	status = "okay";
+};
+
+&usb_host0_xhci {
+	status = "okay";
+};
+
+&usb_host1_xhci {
+	status = "okay";
+};
+
+&usb_host0_ehci {
+	status = "okay";
+};
+
+&usb_host0_ohci {
+	status = "okay";
+};
+
+&vop {
+	assigned-clocks = <&cru DCLK_VOP0>, <&cru DCLK_VOP1>;
+	assigned-clock-parents = <&pmucru PLL_HPLL>, <&cru PLL_VPLL>;
+	status = "okay";
+};
+
+&vop_mmu {
+	status = "okay";
+};
+
+&vp0 {
+	vp0_out_hdmi: endpoint@ROCKCHIP_VOP2_EP_HDMI0 {
+		reg = <ROCKCHIP_VOP2_EP_HDMI0>;
+		remote-endpoint = <&hdmi_in_vp0>;
+	};
+};
diff --git a/arch/arm64/boot/dts/rockchip/rk3566-roc-pc.dts b/arch/arm64/boot/dts/rockchip/rk3566-roc-pc.dts
new file mode 100644
index 000000000000..dba648c2f57e
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3566-roc-pc.dts
@@ -0,0 +1,631 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/rockchip.h>
+#include <dt-bindings/soc/rockchip,vop2.h>
+#include "rk3566.dtsi"
+
+/ {
+	model = "Firefly Station M2";
+	compatible = "firefly,rk3566-roc-pc", "rockchip,rk3566";
+
+	aliases {
+		mmc0 = &sdmmc0;
+		mmc1 = &sdhci;
+		mmc2 = &sdmmc1;
+	};
+
+	chosen: chosen {
+		stdout-path = "serial2:1500000n8";
+	};
+
+	gmac1_clkin: external-gmac1-clock {
+		compatible = "fixed-clock";
+		clock-frequency = <125000000>;
+		clock-output-names = "gmac1_clkin";
+		#clock-cells = <0>;
+	};
+
+	hdmi-con {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con_in: endpoint {
+				remote-endpoint = <&hdmi_out_con>;
+			};
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-user {
+			label = "user-led";
+			default-state = "on";
+			gpios = <&gpio0 RK_PD3 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+			pinctrl-names = "default";
+			pinctrl-0 = <&user_led_enable_h>;
+			retain-state-suspended;
+		};
+	};
+
+	sdio_pwrseq: sdio-pwrseq {
+		status = "okay";
+		compatible = "mmc-pwrseq-simple";
+		clocks = <&rk809 1>;
+		clock-names = "ext_clock";
+		pinctrl-names = "default";
+		pinctrl-0 = <&wifi_enable_h>;
+		reset-gpios = <&gpio2 RK_PB1 GPIO_ACTIVE_LOW>;
+	};
+
+	usb_5v: usb-5v-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "usb_5v";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	vcc5v0_sys: vcc5v0-sys-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc5v0_sys";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&usb_5v>;
+	};
+
+	vcc3v3_sys: vcc3v3-sys-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3_sys";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		vin-supply = <&vcc5v0_sys>;
+	};
+
+	vcc5v0_usb30_host: vcc5v0-usb30-host-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc5v0_usb30_host";
+		enable-active-high;
+		gpio = <&gpio0 RK_PC5 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vcc5v0_usb30_host_en_h>;
+		regulator-always-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc5v0_sys>;
+	};
+
+	vcc5v0_usb_otg: vcc5v0-usb-otg-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc5v0_usb_otg";
+		enable-active-high;
+		gpio = <&gpio0 RK_PC6 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vcc5v0_usb_otg_en_h>;
+		regulator-always-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc5v0_sys>;
+	};
+};
+
+&combphy1 {
+	status = "okay";
+};
+
+&cpu0 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&cpu1 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&cpu2 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&cpu3 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&gmac1 {
+	assigned-clocks = <&cru SCLK_GMAC1_RX_TX>, <&cru SCLK_GMAC1_RGMII_SPEED>, <&cru SCLK_GMAC1>;
+	assigned-clock-parents = <&cru SCLK_GMAC1_RGMII_SPEED>, <&cru SCLK_GMAC1>, <&gmac1_clkin>;
+	clock_in_out = "input";
+	phy-mode = "rgmii-id";
+	phy-supply = <&vcc_3v3>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&gmac1m0_miim
+		     &gmac1m0_tx_bus2
+		     &gmac1m0_rx_bus2
+		     &gmac1m0_rgmii_clk
+		     &gmac1m0_clkinout
+		     &gmac1m0_rgmii_bus>;
+	snps,reset-gpio = <&gpio0 RK_PB7 GPIO_ACTIVE_LOW>;
+	snps,reset-active-low;
+	/* Reset time is 20ms, 100ms for rtl8211f */
+	snps,reset-delays-us = <0 20000 100000>;
+	tx_delay = <0x4f>;
+	rx_delay = <0x24>;
+	phy-handle = <&rgmii_phy1>;
+	status = "okay";
+};
+
+&gpu {
+	mali-supply = <&vdd_gpu>;
+	status = "okay";
+};
+
+&hdmi {
+	avdd-0v9-supply = <&vdda0v9_image>;
+	avdd-1v8-supply = <&vcca1v8_image>;
+	status = "okay";
+};
+
+&hdmi_in {
+	hdmi_in_vp0: endpoint {
+		remote-endpoint = <&vp0_out_hdmi>;
+	};
+};
+
+&hdmi_out {
+	hdmi_out_con: endpoint {
+		remote-endpoint = <&hdmi_con_in>;
+	};
+};
+
+&i2c0 {
+	status = "okay";
+
+	vdd_cpu: regulator@1c {
+		compatible = "tcs,tcs4525";
+		reg = <0x1c>;
+		fcs,suspend-voltage-selector = <1>;
+		regulator-name = "vdd_cpu";
+		regulator-min-microvolt = <800000>;
+		regulator-max-microvolt = <1150000>;
+		regulator-ramp-delay = <2300>;
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&vcc5v0_sys>;
+
+		regulator-state-mem {
+			regulator-off-in-suspend;
+		};
+	};
+
+	rk809: pmic@20 {
+		compatible = "rockchip,rk809";
+		reg = <0x20>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <RK_PA7 IRQ_TYPE_LEVEL_LOW>;
+		clock-output-names = "rk808-clkout1", "rk808-clkout2";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_int>;
+		rockchip,system-power-controller;
+		wakeup-source;
+		#clock-cells = <1>;
+
+		vcc1-supply = <&vcc3v3_sys>;
+		vcc2-supply = <&vcc3v3_sys>;
+		vcc3-supply = <&vcc3v3_sys>;
+		vcc4-supply = <&vcc3v3_sys>;
+		vcc5-supply = <&vcc3v3_sys>;
+		vcc6-supply = <&vcc3v3_sys>;
+		vcc7-supply = <&vcc3v3_sys>;
+		vcc8-supply = <&vcc3v3_sys>;
+		vcc9-supply = <&vcc3v3_sys>;
+
+		regulators {
+			vdd_log: DCDC_REG1 {
+				regulator-name = "vdd_log";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-init-microvolt = <900000>;
+				regulator-ramp-delay = <6001>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <900000>;
+				};
+			};
+
+			vdd_gpu: DCDC_REG2 {
+				regulator-name = "vdd_gpu";
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-init-microvolt = <900000>;
+				regulator-ramp-delay = <6001>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+					regulator-suspend-microvolt = <900000>;
+				};
+			};
+
+			vcc_ddr: DCDC_REG3 {
+				regulator-name = "vcc_ddr";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1100000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-initial-mode = <0x2>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vdd_npu: DCDC_REG4 {
+				regulator-name = "vdd_npu";
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-initial-mode = <0x2>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_1v8: DCDC_REG5 {
+				regulator-name = "vcc_1v8";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vdda0v9_image: LDO_REG1 {
+				regulator-name = "vdda0v9_image";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <900000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <900000>;
+				};
+			};
+
+			vdda_0v9: LDO_REG2 {
+				regulator-name = "vdda_0v9";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <900000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <900000>;
+				};
+			};
+
+			vdda0v9_pmu: LDO_REG3 {
+				regulator-name = "vdda0v9_pmu";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <900000>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <900000>;
+				};
+			};
+
+			vccio_acodec: LDO_REG4 {
+				regulator-name = "vccio_acodec";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+
+				};
+			};
+
+			vccio_sd: LDO_REG5 {
+				regulator-name = "vccio_sd";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+				};
+			};
+
+			vcc3v3_pmu: LDO_REG6 {
+				regulator-name = "vcc3v3_pmu";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+				};
+			};
+
+			vcca_1v8: LDO_REG7 {
+				regulator-name = "vcca_1v8";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vcca1v8_pmu: LDO_REG8 {
+				regulator-name = "vcca1v8_pmu";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vcca1v8_image: LDO_REG9 {
+				regulator-name = "vcca1v8_image";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vcc_3v3: SWITCH_REG1 {
+				regulator-boot-on;
+				regulator-name = "vcc3v3";
+			};
+
+			vcc3v3_sd: SWITCH_REG2 {
+				regulator-name = "vcc3v3_sd";
+				regulator-always-on;
+				regulator-boot-on;
+			};
+		};
+	};
+};
+
+&i2c1 {
+	status = "okay";
+};
+
+&i2c2 {
+	status = "okay";
+};
+
+&i2c3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c3m1_xfer>;
+	status = "okay";
+};
+
+&i2c5 {
+	status = "okay";
+};
+
+&mdio1 {
+	rgmii_phy1: ethernet-phy@0 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0x0>;
+	};
+};
+
+&pinctrl {
+	bt {
+		bt_enable_h: bt-enable-h {
+			rockchip,pins = <0 RK_PC1 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		bt_host_wake_l: bt-host-wake-l {
+			rockchip,pins = <0 RK_PB3 RK_FUNC_GPIO &pcfg_pull_down>;
+		};
+
+		bt_wake_l: bt-wake-l {
+			rockchip,pins = <0 RK_PB4 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	leds {
+		user_led_enable_h: user-led-enable-h {
+			rockchip,pins = <0 RK_PD3 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	pmic {
+		pmic_int: pmic_int {
+			rockchip,pins =
+				<0 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	sdio-pwrseq {
+		wifi_enable_h: wifi-enable-h {
+			rockchip,pins = <2 RK_PB1 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	usb {
+		vcc5v0_usb30_host_en_h: vcc5v0-usb30-host-en_h {
+			rockchip,pins = <0 RK_PC5 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		vcc5v0_usb_otg_en_h: vcc5v0-usb-otg-en_h {
+			rockchip,pins = <0 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+};
+
+&pmu_io_domains {
+	status = "okay";
+	pmuio1-supply = <&vcc3v3_pmu>;
+	pmuio2-supply = <&vcc3v3_pmu>;
+	vccio1-supply = <&vccio_acodec>;
+	vccio2-supply = <&vcc_1v8>;
+	vccio3-supply = <&vccio_sd>;
+	vccio4-supply = <&vcc_1v8>;
+	vccio5-supply = <&vcc_3v3>;
+	vccio6-supply = <&vcc_1v8>;
+	vccio7-supply = <&vcc_3v3>;
+};
+
+&sdhci {
+	bus-width = <8>;
+	mmc-hs200-1_8v;
+	non-removable;
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&vcc_1v8>;
+	status = "okay";
+};
+
+&sdmmc0 {
+	bus-width = <4>;
+	cap-sd-highspeed;
+	cd-gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_LOW>;
+	disable-wp;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc0_bus4 &sdmmc0_clk &sdmmc0_cmd &sdmmc0_det>;
+	sd-uhs-sdr104;
+	vmmc-supply = <&vcc3v3_sd>;
+	vqmmc-supply = <&vccio_sd>;
+	status = "okay";
+};
+
+&sdmmc1 {
+	bus-width = <4>;
+	cap-sd-highspeed;
+	cap-sdio-irq;
+	keep-power-in-suspend;
+	mmc-pwrseq = <&sdio_pwrseq>;
+	vmmc-supply = <&vcc3v3_sys>;
+	vqmmc-supply = <&vcca1v8_pmu>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc1_bus4 &sdmmc1_cmd &sdmmc1_clk>;
+	status = "okay";
+};
+
+&tsadc {
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_xfer>;
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1m0_xfer &uart1m0_ctsn>;
+	status = "okay";
+	uart-has-rtscts;
+
+	bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		clocks = <&rk809 1>;
+		clock-names = "lpo";
+		device-wakeup-gpios = <&gpio2 RK_PC1 GPIO_ACTIVE_HIGH>;
+		host-wakeup-gpios = <&gpio2 RK_PC0 GPIO_ACTIVE_HIGH>;
+		shutdown-gpios = <&gpio2 RK_PB7 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&bt_host_wake_l &bt_wake_l &bt_enable_h>;
+		vbat-supply = <&vcc3v3_sys>;
+		vddio-supply = <&vcca1v8_pmu>;
+	};
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&usb2phy0_host {
+	phy-supply = <&vcc5v0_usb30_host>;
+	status = "okay";
+};
+
+&usb2phy0_otg {
+	phy-supply = <&vcc5v0_usb_otg>;
+	status = "okay";
+};
+
+&usb2phy1_otg {
+	phy-supply = <&vcc5v0_usb30_host>;
+	status = "okay";
+};
+
+&usb2phy0 {
+	status = "okay";
+};
+
+&usb2phy1 {
+	status = "okay";
+};
+
+&usb_host0_xhci {
+	status = "okay";
+};
+
+&usb_host1_xhci {
+	status = "okay";
+};
+
+&usb_host0_ehci {
+	status = "okay";
+};
+
+&usb_host0_ohci {
+	status = "okay";
+};
+
+&vop {
+	assigned-clocks = <&cru DCLK_VOP0>, <&cru DCLK_VOP1>;
+	assigned-clock-parents = <&pmucru PLL_HPLL>, <&cru PLL_VPLL>;
+	status = "okay";
+};
+
+&vop_mmu {
+	status = "okay";
+};
+
+&vp0 {
+	vp0_out_hdmi: endpoint@ROCKCHIP_VOP2_EP_HDMI0 {
+		reg = <ROCKCHIP_VOP2_EP_HDMI0>;
+		remote-endpoint = <&hdmi_in_vp0>;
+	};
+};
diff --git a/arch/arm64/boot/dts/rockchip/rk3566-soquartz-cm4.dts b/arch/arm64/boot/dts/rockchip/rk3566-soquartz-cm4.dts
new file mode 100644
index 000000000000..e00568a6be5c
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3566-soquartz-cm4.dts
@@ -0,0 +1,177 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+/dts-v1/;
+
+#include "rk3566-soquartz.dtsi"
+
+/ {
+	model = "Pine64 RK3566 SoQuartz with CM4-IO Carrier Board";
+	compatible = "pine64,soquartz-cm4io", "pine64,soquartz", "rockchip,rk3566";
+
+	/* labeled +12v in schematic */
+	vcc12v_dcin: vcc12v-dcin-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc12v_dcin";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+	};
+
+	/* labeled +5v in schematic */
+	vcc_5v: vcc-5v-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_5v";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc12v_dcin>;
+	};
+};
+
+&gmac1 {
+	status = "okay";
+};
+
+/*
+ * i2c1 is exposed on CM1 / Module1A
+ * pin 80 - SCL0 - i2c1_scl_m0, pullup to vcc3v3_pmu
+ * pin 82 - SDA0 - i2c1_sda_m0, pullup to vcc3v3_pmu
+ */
+&i2c1 {
+	status = "okay";
+
+	/*
+	 * the rtc interrupt is tied to PMIC_PWRON,
+	 * it will force reset the board if triggered.
+	 */
+	pcf85063: rtc@51 {
+		compatible = "nxp,pcf85063";
+		reg = <0x51>;
+	};
+};
+
+/*
+ * i2c2 is exposed on CM1 / Module1A - to PI40
+ * pin 56 - GPIO3 - i2c2_scl_m1, pullup to vcc_3v3, shared with i2s1_8ch
+ * pin 58 - GPIO2 - i2c2_sda_m1, pullup to vcc_3v3
+ */
+&i2c2 {
+	status = "disabled";
+};
+
+/*
+ * i2c3 is exposed on CM1 / Module1A - to PI40
+ * pin 35 - ID_SC(GPIO28) - i2c3_scl_m0, pullup to vcc_3v3
+ * pin 36 - ID_SD(GPIO27) - i2c3_sda_m0, pullup to vcc_3v3
+ */
+&i2c3 {
+	status = "disabled";
+};
+
+/*
+ * i2c4 is exposed on CM2 / Module1B - to PI40
+ * pin 45 - GPIO24 - i2c4_scl_m1
+ * pin 47 - GPIO23 - i2c4_sda_m1
+ */
+&i2c4 {
+	status = "disabled";
+};
+
+/*
+ * i2s1_8ch is exposed on CM1 / Module1A - to PI40
+ * pin 24 - GPIO26 - i2s1_sdi1_m1
+ * pin 25 - GPIO21 - i2s1_sdo0_m1
+ * pin 26 - GPIO19 - i2s1_lrck_tx_m1
+ * pin 27 - GPIO20 - i2s1_sdi0_m1
+ * pin 29 - GPIO16 - i2s1_sdi3_m1
+ * pin 30 - GPIO6  - i2s1_sdi2_m1
+ * pin 40 - GPIO9  - i2s1_sdo1_m1, shared with spi3
+ * pin 41 - GPIO25 - i2s1_sdo2_m1
+ * pin 49 - GPIO18 - i2s1_sclk_tx_m1
+ * pin 50 - GPIO17 - i2s1_mclk_m1
+ * pin 56 - GPIO3  - i2s1_sdo3_m1, shared with i2c2
+ */
+&i2s1_8ch {
+	status = "disabled";
+};
+
+&led_diy {
+	status = "okay";
+};
+
+&led_work {
+	status = "okay";
+};
+
+&rgmii_phy1 {
+	status = "okay";
+};
+
+/*
+ * saradc is exposed on CM1 / Module1A - to J2
+ * pin 94 - AIN1 - saradc_vin3
+ * pin 96 - AIN0 - saradc_vin2
+ */
+&saradc {
+	status = "disabled";
+};
+
+&sdmmc0 {
+	vmmc-supply = <&sdmmc_pwr>;
+	status = "okay";
+};
+
+&sdmmc_pwr {
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	status = "okay";
+};
+
+/*
+ *  spi3 is exposed on CM1 / Module1A - to PI40
+ * pin 37 - GPIO7  - spi3_cs1_m0
+ * pin 38 - GPIO11 - spi3_clk_m0
+ * pin 39 - GPIO8  - spi3_cs0_m0
+ * pin 40 - GPIO9  - spi3_miso_m0, shared with i2s1_8ch
+ * pin 44 - GPIO10 - spi3_mosi_m0
+ */
+&spi3 {
+	status = "disabled";
+};
+
+/*
+ * uart2 is exposed on CM1 / Module1A - to PI40
+ * pin 51 - GPIO15 - uart2_rx_m0
+ * pin 55 - GPIO14 - uart2_tx_m0
+ */
+&uart2 {
+	status = "okay";
+};
+
+/*
+ * uart7 is exposed on CM1 / Module1A - to PI40
+ * pin 46 - GPIO22 - uart7_tx_m2
+ * pin 47 - GPIO23 - uart7_rx_m2
+ */
+&uart7 {
+	status = "okay";
+};
+
+&usb2phy0 {
+	status = "okay";
+};
+
+&usb2phy0_otg {
+	phy-supply = <&vcc_5v>;
+	status = "okay";
+};
+
+&usb_host0_xhci {
+	status = "okay";
+};
+
+&vbus {
+	vin-supply = <&vcc_5v>;
+};
diff --git a/arch/arm64/boot/dts/rockchip/rk3566-soquartz.dtsi b/arch/arm64/boot/dts/rockchip/rk3566-soquartz.dtsi
new file mode 100644
index 000000000000..5bcd4be32964
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3566-soquartz.dtsi
@@ -0,0 +1,616 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/rockchip.h>
+#include "rk3566.dtsi"
+
+/ {
+	model = "Pine64 RK3566 SoQuartz SOM";
+	compatible = "pine64,soquartz", "rockchip,rk3566";
+
+	aliases {
+		ethernet0 = &gmac1;
+		mmc0 = &sdmmc0;
+		mmc1 = &sdhci;
+		mmc2 = &sdmmc1;
+	};
+
+	chosen: chosen {
+		stdout-path = "serial2:1500000n8";
+	};
+
+	gmac1_clkin: external-gmac1-clock {
+		compatible = "fixed-clock";
+		clock-frequency = <125000000>;
+		clock-output-names = "gmac1_clkin";
+		#clock-cells = <0>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led_diy: led-diy {
+			label = "diy-led";
+			default-state = "on";
+			gpios = <&gpio0 RK_PC1 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "heartbeat";
+			pinctrl-names = "default";
+			pinctrl-0 = <&diy_led_enable_h>;
+			retain-state-suspended;
+			status = "disabled";
+		};
+
+		led_work: led-work {
+			label = "work-led";
+			default-state = "off";
+			gpios = <&gpio0 RK_PC0 GPIO_ACTIVE_LOW>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&work_led_enable_h>;
+			retain-state-suspended;
+			status = "disabled";
+		};
+	};
+
+	sdio_pwrseq: sdio-pwrseq {
+		status = "okay";
+		compatible = "mmc-pwrseq-simple";
+		clocks = <&rk809 1>;
+		clock-names = "ext_clock";
+		pinctrl-names = "default";
+		pinctrl-0 = <&wifi_enable_h>;
+		reset-gpios = <&gpio2 RK_PC2 GPIO_ACTIVE_LOW>;
+	};
+
+	vbus: vbus-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vbus";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	/* sourced from vbus, vbus is provided by the carrier board */
+	vcc5v0_sys: vcc5v0-sys-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc5v0_sys";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vbus>;
+	};
+
+	vcc3v3_sys: vcc3v3-sys-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3_sys";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc5v0_sys>;
+	};
+
+	sdmmc_pwr: sdmmc-pwr-regulator {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio0 RK_PA5 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&sdmmc_pwr_h>;
+		regulator-name = "sdmmc_pwr";
+		status = "disabled";
+	};
+};
+
+&cpu0 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&cpu1 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&cpu2 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&cpu3 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&gmac1 {
+	assigned-clocks = <&cru SCLK_GMAC1_RX_TX>, <&cru SCLK_GMAC1_RGMII_SPEED>, <&cru SCLK_GMAC1>;
+	assigned-clock-parents = <&cru SCLK_GMAC1_RGMII_SPEED>, <&cru SCLK_GMAC1>, <&gmac1_clkin>;
+	clock_in_out = "input";
+	phy-supply = <&vcc_3v3>;
+	phy-mode = "rgmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&gmac1m0_miim
+		     &gmac1m0_tx_bus2
+		     &gmac1m0_rx_bus2
+		     &gmac1m0_rgmii_clk
+		     &gmac1m0_clkinout
+		     &gmac1m0_rgmii_bus>;
+	snps,reset-gpio = <&gpio0 RK_PC3 GPIO_ACTIVE_LOW>;
+	snps,reset-active-low;
+	/* Reset time is 20ms, 100ms for rtl8211f, also works well here */
+	snps,reset-delays-us = <0 20000 100000>;
+	tx_delay = <0x30>;
+	rx_delay = <0x10>;
+	phy-handle = <&rgmii_phy1>;
+	status = "disabled";
+};
+
+&i2c0 {
+	status = "okay";
+
+	vdd_cpu: regulator@1c {
+		compatible = "tcs,tcs4525";
+		reg = <0x1c>;
+		fcs,suspend-voltage-selector = <1>;
+		regulator-name = "vdd_cpu";
+		regulator-min-microvolt = <800000>;
+		regulator-max-microvolt = <1150000>;
+		regulator-ramp-delay = <2300>;
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&vcc5v0_sys>;
+
+		regulator-state-mem {
+			regulator-off-in-suspend;
+		};
+	};
+
+	rk809: pmic@20 {
+		compatible = "rockchip,rk809";
+		reg = <0x20>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <RK_PA3 IRQ_TYPE_LEVEL_LOW>;
+		#clock-cells = <1>;
+		clock-output-names = "rk808-clkout1", "rk808-clkout2";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_int_l>;
+		rockchip,system-power-controller;
+		wakeup-source;
+
+		vcc1-supply = <&vcc3v3_sys>;
+		vcc2-supply = <&vcc3v3_sys>;
+		vcc3-supply = <&vcc3v3_sys>;
+		vcc4-supply = <&vcc3v3_sys>;
+		vcc5-supply = <&vcc3v3_sys>;
+		vcc6-supply = <&vcc3v3_sys>;
+		vcc7-supply = <&vcc3v3_sys>;
+		vcc8-supply = <&vcc3v3_sys>;
+		vcc9-supply = <&vcc3v3_sys>;
+
+		regulators {
+			vdd_logic: DCDC_REG1 {
+				regulator-name = "vdd_logic";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-init-microvolt = <900000>;
+				regulator-ramp-delay = <6001>;
+				regulator-initial-mode = <0x2>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <900000>;
+				};
+			};
+
+			vdd_gpu: DCDC_REG2 {
+				regulator-name = "vdd_gpu";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-init-microvolt = <900000>;
+				regulator-ramp-delay = <6001>;
+				regulator-initial-mode = <0x2>;
+					regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_ddr: DCDC_REG3 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-initial-mode = <0x2>;
+				regulator-name = "vcc_ddr";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vdd_npu: DCDC_REG4 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-init-microvolt = <900000>;
+				regulator-initial-mode = <0x2>;
+				regulator-name = "vdd_npu";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_1v8: DCDC_REG5 {
+				regulator-name = "vcc_1v8";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vdda0v9_image: LDO_REG1 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <900000>;
+				regulator-name = "vdda0v9_image";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <900000>;
+				};
+			};
+
+			vdda_0v9: LDO_REG2 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <900000>;
+				regulator-name = "vdda_0v9";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdda0v9_pmu: LDO_REG3 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <900000>;
+				regulator-name = "vdda0v9_pmu";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <900000>;
+				};
+			};
+
+			vccio_acodec: LDO_REG4 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vccio_acodec";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vccio_sd: LDO_REG5 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vccio_sd";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc3v3_pmu: LDO_REG6 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc3v3_pmu";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+				};
+			};
+
+			vcca_1v8: LDO_REG7 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcca_1v8";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcca1v8_pmu: LDO_REG8 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcca1v8_pmu";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcca1v8_image: LDO_REG9 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcca1v8_image";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_3v3: SWITCH_REG1 {
+				regulator-name = "vcc_3v3";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc3v3_sd: SWITCH_REG2 {
+				regulator-name = "vcc3v3_sd";
+				status = "disabled";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+		};
+	};
+};
+
+/*
+ * i2c1 is exposed on CM1 / Module1A
+ * pin 80 - i2c1_scl_m0, pullup to vcc3v3_pmu
+ * pin 82 - i2c1_sda_m0, pullup to vcc3v3_pmu
+ */
+&i2c1 {
+	status = "disabled";
+};
+
+/*
+ * i2c2 is exposed on CM1 / Module1A
+ * pin 56 - i2c2_scl_m1, pullup to vcc_3v3, shared with i2s1_8ch
+ * pin 58 - i2c2_sda_m1, pullup to vcc_3v3
+ */
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2m1_xfer>;
+	status = "disabled";
+};
+
+/*
+ * i2c3 is exposed on CM1 / Module1A
+ * pin 35 - i2c3_scl_m0, pullup to vcc_3v3
+ * pin 36 - i2c3_sda_m0, pullup to vcc_3v3
+ */
+&i2c3 {
+	status = "disabled";
+};
+
+/*
+ * i2c4 is exposed on CM2 / Module1B
+ * pin 45 - i2c4_scl_m1
+ * pin 47 - i2c4_sda_m1
+ */
+&i2c4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c4m1_xfer>;
+	status = "disabled";
+};
+
+/*
+ * i2s1_8ch is exposed on CM1 / Module1A
+ * pin 24 - i2s1_sdi1_m1
+ * pin 25 - i2s1_sdo0_m1
+ * pin 26 - i2s1_lrck_tx_m1
+ * pin 27 - i2s1_sdi0_m1
+ * pin 29 - i2s1_sdi3_m1
+ * pin 30 - i2s1_sdi2_m1
+ * pin 40 - i2s1_sdo1_m1, shared with spi3
+ * pin 41 - i2s1_sdo2_m1
+ * pin 49 - i2s1_sclk_tx_m1
+ * pin 50 - i2s1_mclk_m1
+ * pin 56 - i2s1_sdo3_m1, shared with i2c2
+ */
+&i2s1_8ch {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2s1m1_sclktx &i2s1m1_sclkrx
+		     &i2s1m1_lrcktx &i2s1m1_lrckrx
+		     &i2s1m1_sdi0   &i2s1m1_sdi1
+		     &i2s1m1_sdi2   &i2s1m1_sdi3
+		     &i2s1m1_sdo0   &i2s1m1_sdo1
+		     &i2s1m1_sdo2   &i2s1m1_sdo3>;
+	status = "disabled";
+};
+
+&mdio1 {
+	rgmii_phy1: ethernet-phy@0 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0>;
+		status = "disabled";
+	};
+};
+
+&pinctrl {
+	bt {
+		bt_enable_h: bt-enable-h {
+			rockchip,pins = <2 RK_PB7 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		bt_host_wake_l: bt-host-wake-l {
+			rockchip,pins = <2 RK_PC0 RK_FUNC_GPIO &pcfg_pull_down>;
+		};
+
+		bt_wake_l: bt-wake-l {
+			rockchip,pins = <2 RK_PC1 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	leds {
+		work_led_enable_h: work-led-enable-h {
+			rockchip,pins = <0 RK_PC0 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		diy_led_enable_h: diy-led-enable-h {
+			rockchip,pins = <0 RK_PC1 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	pmic {
+		pmic_int_l: pmic-int-l {
+			rockchip,pins = <0 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	sdio-pwrseq {
+		wifi_enable_h: wifi-enable-h {
+			rockchip,pins = <2 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	sdmmc-pwr {
+		sdmmc_pwr_h: sdmmc-pwr-h {
+			rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+};
+
+&pmu_io_domains {
+	pmuio1-supply = <&vcc3v3_pmu>;
+	pmuio2-supply = <&vcc3v3_pmu>;
+	vccio1-supply = <&vcc_3v3>;
+	vccio2-supply = <&vcc_1v8>;
+	vccio3-supply = <&vccio_sd>;
+	vccio4-supply = <&vcc_1v8>;
+	vccio5-supply = <&vcc_3v3>;
+	vccio6-supply = <&vcc_3v3>;
+	vccio7-supply = <&vcc_3v3>;
+	status = "okay";
+};
+
+/*
+ * saradc is exposed on CM1 / Module1A
+ * pin 94 - saradc_vin3
+ * pin 96 - saradc_vin2
+ */
+&saradc {
+	vref-supply = <&vcca_1v8>;
+	status = "disabled";
+};
+
+&sdhci {
+	bus-width = <8>;
+	mmc-hs200-1_8v;
+	non-removable;
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&vcc_1v8>;
+	status = "okay";
+};
+
+&sdmmc0 {
+	broken-cd;
+	bus-width = <4>;
+	cap-sd-highspeed;
+	disable-wp;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc0_bus4 &sdmmc0_clk &sdmmc0_cmd &sdmmc0_det>;
+	vqmmc-supply = <&vccio_sd>;
+	status = "disabled";
+};
+
+&sdmmc1 {
+	bus-width = <4>;
+	cap-sd-highspeed;
+	cap-sdio-irq;
+	keep-power-in-suspend;
+	mmc-pwrseq = <&sdio_pwrseq>;
+	non-removable;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc1_bus4 &sdmmc1_cmd &sdmmc1_clk>;
+	sd-uhs-sdr104;
+	vmmc-supply = <&vcc3v3_sys>;
+	vqmmc-supply = <&vcc_1v8>;
+	status = "okay";
+};
+
+/*
+ * spi3 is exposed on CM1 / Module1A
+ * pin 37 - spi3_cs1_m0
+ * pin 38 - spi3_clk_m0
+ * pin 39 - spi3_cs0_m0
+ * pin 40 - spi3_miso_m0, shared with i2s1_8ch
+ * pin 44 - spi3_mosi_m0
+ */
+&spi3 {
+	status = "disabled";
+};
+
+&tsadc {
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1m0_xfer &uart1m0_ctsn &uart1m0_rtsn>;
+	uart-has-rtscts;
+	status = "okay";
+
+	bluetooth {
+		compatible = "brcm,bcm43438-bt";
+		clocks = <&rk809 1>;
+		clock-names = "lpo";
+		device-wakeup-gpios = <&gpio2 RK_PC1 GPIO_ACTIVE_HIGH>;
+		host-wakeup-gpios = <&gpio2 RK_PC0 GPIO_ACTIVE_HIGH>;
+		shutdown-gpios = <&gpio2 RK_PB7 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&bt_host_wake_l &bt_wake_l &bt_enable_h>;
+		vbat-supply = <&vcc3v3_sys>;
+		vddio-supply = <&vcca1v8_pmu>;
+	};
+};
+
+/*
+ * uart2 is exposed on CM1 / Module1A
+ * pin 51 - uart2_rx_m0
+ * pin 55 - uart2_tx_m0
+ */
+&uart2 {
+	status = "disabled";
+};
+
+/*
+ * uart7 is exposed on CM1 / Module1A
+ * pin 46 - uart7_tx_m2
+ * pin 47 - uart7_rx_m2
+ */
+&uart7 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart7m2_xfer>;
+	status = "disabled";
+};
+
+/* dwc3_otg is the only usb port available */
+&usb2phy0 {
+	status = "disabled";
+};
+
+&usb2phy0_otg {
+	status = "disabled";
+};
+
+&usb_host0_xhci {
+	status = "disabled";
+};
diff --git a/arch/arm64/boot/dts/rockchip/rk3566.dtsi b/arch/arm64/boot/dts/rockchip/rk3566.dtsi
index 3839eef5e4f7..6c4b17d27bdc 100644
--- a/arch/arm64/boot/dts/rockchip/rk3566.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3566.dtsi
@@ -6,6 +6,10 @@
 	compatible = "rockchip,rk3566";
 };
 
+&pipegrf {
+	compatible = "rockchip,rk3566-pipe-grf", "syscon";
+};
+
 &power {
 	power-domain@RK3568_PD_PIPE {
 		reg = <RK3568_PD_PIPE>;
@@ -18,3 +22,14 @@
 		#power-domain-cells = <0>;
 	};
 };
+
+&usb_host0_xhci {
+	phys = <&usb2phy0_otg>;
+	phy-names = "usb2-phy";
+	extcon = <&usb2phy0>;
+	maximum-speed = "high-speed";
+};
+
+&vop {
+	compatible = "rockchip,rk3566-vop";
+};
diff --git a/arch/arm64/boot/dts/rockchip/rk3568-bpi-r2-pro.dts b/arch/arm64/boot/dts/rockchip/rk3568-bpi-r2-pro.dts
new file mode 100644
index 000000000000..c282f6e79960
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3568-bpi-r2-pro.dts
@@ -0,0 +1,843 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Author: Frank Wunderlich <frank-w@public-files.de>
+ *
+ */
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/rockchip.h>
+#include <dt-bindings/soc/rockchip,vop2.h>
+#include "rk3568.dtsi"
+
+/ {
+	model = "Bananapi-R2 Pro (RK3568) DDR4 Board";
+	compatible = "rockchip,rk3568-bpi-r2pro", "rockchip,rk3568";
+
+	aliases {
+		ethernet0 = &gmac0;
+		ethernet1 = &gmac1;
+		mmc0 = &sdmmc0;
+		mmc1 = &sdhci;
+	};
+
+	chosen: chosen {
+		stdout-path = "serial2:1500000n8";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&blue_led_pin &green_led_pin>;
+
+		blue_led: led-0 {
+			color = <LED_COLOR_ID_BLUE>;
+			default-state = "off";
+			function = LED_FUNCTION_STATUS;
+			gpios = <&gpio0 RK_PD6 GPIO_ACTIVE_HIGH>;
+		};
+
+		green_led: led-1 {
+			color = <LED_COLOR_ID_GREEN>;
+			default-state = "on";
+			function = LED_FUNCTION_POWER;
+			gpios = <&gpio0 RK_PD5 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	dc_12v: dc-12v-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "dc_12v";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+	};
+
+	hdmi-con {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con_in: endpoint {
+				remote-endpoint = <&hdmi_out_con>;
+			};
+		};
+	};
+
+	vcc3v3_sys: vcc3v3-sys-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3_sys";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&dc_12v>;
+	};
+
+	vcc5v0_sys: vcc5v0-sys-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc5v0_sys";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&dc_12v>;
+	};
+
+	pcie30_avdd0v9: pcie30-avdd0v9-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "pcie30_avdd0v9";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <900000>;
+		regulator-max-microvolt = <900000>;
+		vin-supply = <&vcc3v3_sys>;
+	};
+
+	pcie30_avdd1v8: pcie30-avdd1v8-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "pcie30_avdd1v8";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vcc3v3_sys>;
+	};
+
+	/* pi6c pcie clock generator feeds both ports */
+	vcc3v3_pi6c_05: vcc3v3-pi6c-05-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3_pcie";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		enable-active-high;
+		gpios = <&gpio0 RK_PD4 GPIO_ACTIVE_HIGH>;
+		startup-delay-us = <200000>;
+		vin-supply = <&vcc5v0_sys>;
+	};
+
+	/* actually fed by vcc3v3_sys, dependent on pi6c clock generator */
+	vcc3v3_minipcie: vcc3v3-minipcie-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3_minipcie";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		enable-active-high;
+		gpio = <&gpio0 RK_PC6 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&minipcie_enable_h>;
+		startup-delay-us = <50000>;
+		vin-supply = <&vcc3v3_pi6c_05>;
+	};
+
+	/* actually fed by vcc3v3_sys, dependent on pi6c clock generator */
+	vcc3v3_ngff: vcc3v3-ngff-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3_ngff";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		enable-active-high;
+		gpio = <&gpio0 RK_PB7 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&ngffpcie_enable_h>;
+		startup-delay-us = <50000>;
+		vin-supply = <&vcc3v3_pi6c_05>;
+	};
+
+	vcc5v0_usb: vcc5v0-usb-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc5v0_usb";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&dc_12v>;
+	};
+
+	vcc5v0_usb_host: vcc5v0-usb-host-regulator {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio0 RK_PA6 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vcc5v0_usb_host_en>;
+		regulator-name = "vcc5v0_usb_host";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc5v0_usb>;
+	};
+
+	vcc5v0_usb_otg: vcc5v0-usb-otg-regulator {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio0 RK_PA5 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vcc5v0_usb_otg_en>;
+		regulator-name = "vcc5v0_usb_otg";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc5v0_usb>;
+	};
+};
+
+&combphy0 {
+	/* used for USB3 */
+	status = "okay";
+};
+
+&combphy1 {
+	/* used for USB3 */
+	status = "okay";
+};
+
+&combphy2 {
+	/* used for SATA */
+	status = "okay";
+};
+
+&gmac0 {
+	assigned-clocks = <&cru SCLK_GMAC0_RX_TX>, <&cru SCLK_GMAC0>;
+	assigned-clock-parents = <&cru SCLK_GMAC0_RGMII_SPEED>, <&cru CLK_MAC0_2TOP>;
+	clock_in_out = "input";
+	phy-mode = "rgmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&gmac0_miim
+		     &gmac0_tx_bus2
+		     &gmac0_rx_bus2
+		     &gmac0_rgmii_clk
+		     &gmac0_rgmii_bus>;
+	snps,reset-gpio = <&gpio3 RK_PB7 GPIO_ACTIVE_LOW>;
+	snps,reset-active-low;
+	/* Reset time is 20ms, 100ms for rtl8211f */
+	snps,reset-delays-us = <0 20000 100000>;
+	tx_delay = <0x4f>;
+	rx_delay = <0x0f>;
+	status = "okay";
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+		pause;
+	};
+};
+
+&gmac1 {
+	assigned-clocks = <&cru SCLK_GMAC1_RX_TX>, <&cru SCLK_GMAC1>;
+	assigned-clock-parents = <&cru SCLK_GMAC1_RGMII_SPEED>, <&cru CLK_MAC1_2TOP>;
+	clock_in_out = "output";
+	phy-handle = <&rgmii_phy1>;
+	phy-mode = "rgmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&gmac1m1_miim
+		     &gmac1m1_tx_bus2
+		     &gmac1m1_rx_bus2
+		     &gmac1m1_rgmii_clk
+		     &gmac1m1_rgmii_bus>;
+
+	snps,reset-gpio = <&gpio3 RK_PB0 GPIO_ACTIVE_LOW>;
+	snps,reset-active-low;
+	/* Reset time is 20ms, 100ms for rtl8211f */
+	snps,reset-delays-us = <0 20000 100000>;
+
+	tx_delay = <0x3c>;
+	rx_delay = <0x2f>;
+
+	status = "okay";
+};
+
+&gpu {
+	mali-supply = <&vdd_gpu>;
+	status = "okay";
+};
+
+&hdmi {
+	avdd-0v9-supply = <&vdda0v9_image>;
+	avdd-1v8-supply = <&vcca1v8_image>;
+	status = "okay";
+};
+
+&hdmi_in {
+	hdmi_in_vp0: endpoint {
+		remote-endpoint = <&vp0_out_hdmi>;
+	};
+};
+
+&hdmi_out {
+	hdmi_out_con: endpoint {
+		remote-endpoint = <&hdmi_con_in>;
+	};
+};
+
+&hdmi_sound {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	rk809: pmic@20 {
+		compatible = "rockchip,rk809";
+		reg = <0x20>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <RK_PA3 IRQ_TYPE_LEVEL_LOW>;
+		#clock-cells = <1>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_int>;
+		rockchip,system-power-controller;
+		vcc1-supply = <&vcc3v3_sys>;
+		vcc2-supply = <&vcc3v3_sys>;
+		vcc3-supply = <&vcc3v3_sys>;
+		vcc4-supply = <&vcc3v3_sys>;
+		vcc5-supply = <&vcc3v3_sys>;
+		vcc6-supply = <&vcc3v3_sys>;
+		vcc7-supply = <&vcc3v3_sys>;
+		vcc8-supply = <&vcc3v3_sys>;
+		vcc9-supply = <&vcc3v3_sys>;
+		wakeup-source;
+
+		regulators {
+			vdd_logic: DCDC_REG1 {
+				regulator-name = "vdd_logic";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-init-microvolt = <900000>;
+				regulator-initial-mode = <0x2>;
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-ramp-delay = <6001>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdd_gpu: DCDC_REG2 {
+				regulator-name = "vdd_gpu";
+				regulator-always-on;
+				regulator-init-microvolt = <900000>;
+				regulator-initial-mode = <0x2>;
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-ramp-delay = <6001>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_ddr: DCDC_REG3 {
+				regulator-name = "vcc_ddr";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-initial-mode = <0x2>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vdd_npu: DCDC_REG4 {
+				regulator-name = "vdd_npu";
+				regulator-init-microvolt = <900000>;
+				regulator-initial-mode = <0x2>;
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-ramp-delay = <6001>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_1v8: DCDC_REG5 {
+				regulator-name = "vcc_1v8";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdda0v9_image: LDO_REG1 {
+				regulator-name = "vdda0v9_image";
+				regulator-always-on;
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <900000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdda_0v9: LDO_REG2 {
+				regulator-name = "vdda_0v9";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <900000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdda0v9_pmu: LDO_REG3 {
+				regulator-name = "vdda0v9_pmu";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <900000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <900000>;
+				};
+			};
+
+			vccio_acodec: LDO_REG4 {
+				regulator-name = "vccio_acodec";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vccio_sd: LDO_REG5 {
+				regulator-name = "vccio_sd";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc3v3_pmu: LDO_REG6 {
+				regulator-name = "vcc3v3_pmu";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+				};
+			};
+
+			vcca_1v8: LDO_REG7 {
+				regulator-name = "vcca_1v8";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcca1v8_pmu: LDO_REG8 {
+				regulator-name = "vcca1v8_pmu";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vcca1v8_image: LDO_REG9 {
+				regulator-name = "vcca1v8_image";
+				regulator-always-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_3v3: SWITCH_REG1 {
+				regulator-name = "vcc_3v3";
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc3v3_sd: SWITCH_REG2 {
+				regulator-name = "vcc3v3_sd";
+				regulator-always-on;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+		};
+	};
+};
+
+&i2c3 {
+	status = "okay";
+
+	hym8563: rtc@51 {
+		compatible = "haoyu,hym8563";
+		reg = <0x51>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <RK_PD3 IRQ_TYPE_EDGE_FALLING>;
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		clock-output-names = "rtcic_32kout";
+		pinctrl-names = "default";
+		pinctrl-0 = <&hym8563_int>;
+		wakeup-source;
+	};
+};
+
+&i2c5 {
+	/* pin 3 (SDA) + 4 (SCL) of header con2 */
+	status = "disabled";
+};
+
+&i2s0_8ch {
+	/* hdmi sound */
+	status = "okay";
+};
+
+&mdio0 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	switch@0 {
+		compatible = "mediatek,mt7531";
+		reg = <0>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@1 {
+				reg = <1>;
+				label = "lan0";
+			};
+
+			port@2 {
+				reg = <2>;
+				label = "lan1";
+			};
+
+			port@3 {
+				reg = <3>;
+				label = "lan2";
+			};
+
+			port@4 {
+				reg = <4>;
+				label = "lan3";
+			};
+
+			port@5 {
+				reg = <5>;
+				label = "cpu";
+				ethernet = <&gmac0>;
+				phy-mode = "rgmii";
+
+				fixed-link {
+					speed = <1000>;
+					full-duplex;
+					pause;
+				};
+			};
+		};
+	};
+};
+
+&mdio1 {
+	rgmii_phy1: ethernet-phy@0 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0x0>;
+	};
+};
+
+&pcie30phy {
+	data-lanes = <1 2>;
+	phy-supply = <&vcc3v3_pi6c_05>;
+	status = "okay";
+};
+
+&pcie3x1 {
+	/* M.2 slot */
+	num-lanes = <1>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&ngffpcie_reset_h>;
+	reset-gpios = <&gpio3 RK_PA1 GPIO_ACTIVE_HIGH>;
+	vpcie3v3-supply = <&vcc3v3_ngff>;
+	status = "okay";
+};
+
+&pcie3x2 {
+	/* mPCIe slot */
+	num-lanes = <1>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&minipcie_reset_h>;
+	reset-gpios = <&gpio2 RK_PD6 GPIO_ACTIVE_HIGH>;
+	vpcie3v3-supply = <&vcc3v3_minipcie>;
+	status = "okay";
+};
+
+&pinctrl {
+	leds {
+		blue_led_pin: blue-led-pin {
+			rockchip,pins = <0 RK_PD6 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+		green_led_pin: green-led-pin {
+			rockchip,pins = <0 RK_PD5 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	hym8563 {
+		hym8563_int: hym8563-int {
+			rockchip,pins = <0 RK_PD3 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	pcie {
+		minipcie_enable_h: minipcie-enable-h {
+			rockchip,pins = <0 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none_drv_level_5>;
+		};
+
+		ngffpcie_enable_h: ngffpcie-enable-h {
+			rockchip,pins = <0 RK_PB7 RK_FUNC_GPIO &pcfg_pull_none_drv_level_5>;
+		};
+
+		minipcie_reset_h: minipcie-reset-h {
+			rockchip,pins = <2 RK_PD6 RK_FUNC_GPIO &pcfg_pull_none_drv_level_5>;
+		};
+
+		ngffpcie_reset_h: ngffpcie-reset-h {
+			rockchip,pins = <3 RK_PA1 RK_FUNC_GPIO &pcfg_pull_none_drv_level_5>;
+		};
+	};
+
+	pmic {
+		pmic_int: pmic_int {
+			rockchip,pins =
+				<0 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	usb {
+		vcc5v0_usb_host_en: vcc5v0_usb_host_en {
+			rockchip,pins = <0 RK_PA6 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		vcc5v0_usb_otg_en: vcc5v0_usb_otg_en {
+			rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+};
+
+&pmu_io_domains {
+	pmuio1-supply = <&vcc3v3_pmu>;
+	pmuio2-supply = <&vcc3v3_pmu>;
+	vccio1-supply = <&vccio_acodec>;
+	vccio3-supply = <&vccio_sd>;
+	vccio4-supply = <&vcc_3v3>;
+	vccio5-supply = <&vcc_3v3>;
+	vccio6-supply = <&vcc_1v8>;
+	vccio7-supply = <&vcc_3v3>;
+	status = "okay";
+};
+
+&pwm8 {
+	/* fan 5v - gnd - pwm */
+	status = "okay";
+};
+
+&pwm10 {
+	/* pin 7 of header con2 */
+	status = "disabled";
+};
+
+&pwm11 {
+	/* pin 15 of header con2 */
+	status = "disabled";
+};
+
+&pwm12 {
+	/* pin 21 of header con2 */
+	/* shared with uart9 + spi3 */
+	pinctrl-0 = <&pwm12m1_pins>;
+	status = "disabled";
+};
+
+&pwm13 {
+	/* pin 24 of header con2 */
+	/* shared with uart9 */
+	pinctrl-0 = <&pwm13m1_pins>;
+	status = "disabled";
+};
+
+&pwm14 {
+	/* pin 23 of header con2 */
+	/* shared with spi3 */
+	pinctrl-0 = <&pwm14m1_pins>;
+	status = "disabled";
+};
+
+&pwm15 {
+	/* pin 19 of header con2 */
+	/* shared with spi3 */
+	pinctrl-0 = <&pwm15m1_pins>;
+	status = "disabled";
+};
+
+&saradc {
+	vref-supply = <&vcca_1v8>;
+	status = "okay";
+};
+
+&sata2 {
+	status = "okay";
+};
+
+&sdhci {
+	bus-width = <8>;
+	max-frequency = <200000000>;
+	non-removable;
+	pinctrl-names = "default";
+	pinctrl-0 = <&emmc_bus8 &emmc_clk &emmc_cmd &emmc_datastrobe>;
+	status = "okay";
+};
+
+&sdmmc0 {
+	bus-width = <4>;
+	cap-sd-highspeed;
+	cd-gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_LOW>;
+	disable-wp;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc0_bus4 &sdmmc0_clk &sdmmc0_cmd &sdmmc0_det>;
+	sd-uhs-sdr104;
+	vmmc-supply = <&vcc3v3_sd>;
+	vqmmc-supply = <&vccio_sd>;
+	status = "okay";
+};
+
+&spi3 {
+	/* pin 19 (MO) + 21 (MI) + 23 (CK) of header con2 */
+	/* shared with pwm12/14/15 and uart9 */
+	pinctrl-0 = <&spi3m1_pins>;
+	status = "disabled";
+};
+
+&tsadc {
+	rockchip,hw-tshut-mode = <1>;
+	rockchip,hw-tshut-polarity = <0>;
+	status = "okay";
+};
+
+&uart0 {
+	/* pin 8 (TX) + 10 (RX) (RTS:16, CTS:18) of header con2 */
+	status = "disabled";
+};
+
+&uart2 {
+	/* debug-uart */
+	status = "okay";
+};
+
+&uart7 {
+	/* pin 11 (TX) + 13 (RX) of header con2 */
+	pinctrl-0 = <&uart7m1_xfer>;
+	status = "disabled";
+};
+
+&uart9 {
+	/* pin 21 (TX) + 24 (RX) of header con2 */
+	/* shared with pwm13 and pwm12/spi3 */
+	pinctrl-0 = <&uart9m1_xfer>;
+	status = "disabled";
+};
+
+&usb_host0_ehci {
+	status = "okay";
+};
+
+&usb_host0_ohci {
+	status = "okay";
+};
+
+&usb_host0_xhci {
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usb_host1_ehci {
+	status = "okay";
+};
+
+&usb_host1_ohci {
+	status = "okay";
+};
+
+&usb_host1_xhci {
+	status = "okay";
+};
+
+&usb2phy0 {
+	status = "okay";
+};
+
+&usb2phy0_host {
+	phy-supply = <&vcc5v0_usb_host>;
+	status = "okay";
+};
+
+&usb2phy0_otg {
+	phy-supply = <&vcc5v0_usb_otg>;
+	status = "okay";
+};
+
+&usb2phy1 {
+	/* USB for PCIe/M2 */
+	status = "okay";
+};
+
+&usb2phy1_host {
+	status = "okay";
+};
+
+&usb2phy1_otg {
+	status = "okay";
+};
+
+&vop {
+	assigned-clocks = <&cru DCLK_VOP0>, <&cru DCLK_VOP1>;
+	assigned-clock-parents = <&pmucru PLL_HPLL>, <&cru PLL_VPLL>;
+	status = "okay";
+};
+
+&vop_mmu {
+	status = "okay";
+};
+
+&vp0 {
+	vp0_out_hdmi: endpoint@ROCKCHIP_VOP2_EP_HDMI0 {
+		reg = <ROCKCHIP_VOP2_EP_HDMI0>;
+		remote-endpoint = <&hdmi_in_vp0>;
+	};
+};
diff --git a/arch/arm64/boot/dts/rockchip/rk3568-evb1-v10.dts b/arch/arm64/boot/dts/rockchip/rk3568-evb1-v10.dts
index 184e2aa2416a..674792567fa6 100644
--- a/arch/arm64/boot/dts/rockchip/rk3568-evb1-v10.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3568-evb1-v10.dts
@@ -6,7 +6,9 @@
 
 /dts-v1/;
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
 #include <dt-bindings/pinctrl/rockchip.h>
+#include <dt-bindings/soc/rockchip,vop2.h>
 #include "rk3568.dtsi"
 
 / {
@@ -33,6 +35,44 @@
 		regulator-max-microvolt = <12000000>;
 	};
 
+	hdmi-con {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con_in: endpoint {
+				remote-endpoint = <&hdmi_out_con>;
+			};
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led_work: led-0 {
+			gpios = <&gpio0 RK_PC0 GPIO_ACTIVE_HIGH>;
+			function = LED_FUNCTION_HEARTBEAT;
+			color = <LED_COLOR_ID_BLUE>;
+			linux,default-trigger = "heartbeat";
+			pinctrl-names = "default";
+			pinctrl-0 = <&led_work_en>;
+		};
+	};
+
+	rk809-sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,format = "i2s";
+		simple-audio-card,name = "Analog RK809";
+		simple-audio-card,mclk-fs = <256>;
+
+		simple-audio-card,cpu {
+			sound-dai = <&i2s1_8ch>;
+		};
+		simple-audio-card,codec {
+			sound-dai = <&rk809>;
+		};
+	};
+
 	vcc3v3_sys: vcc3v3-sys {
 		compatible = "regulator-fixed";
 		regulator-name = "vcc3v3_sys";
@@ -53,10 +93,50 @@
 		vin-supply = <&dc_12v>;
 	};
 
+	vcc5v0_usb: vcc5v0-usb {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc5v0_usb";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&dc_12v>;
+	};
+
+	vcc5v0_usb_host: vcc5v0-usb-host {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio0 RK_PA6 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vcc5v0_usb_host_en>;
+		regulator-name = "vcc5v0_usb_host";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc5v0_usb>;
+	};
+
+	vcc5v0_usb_otg: vcc5v0-usb-otg {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio0 RK_PA5 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vcc5v0_usb_otg_en>;
+		regulator-name = "vcc5v0_usb_otg";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc5v0_usb>;
+	};
+
 	vcc3v3_lcd0_n: vcc3v3-lcd0-n {
 		compatible = "regulator-fixed";
 		regulator-name = "vcc3v3_lcd0_n";
-		regulator-boot-on;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		enable-active-high;
+		gpio = <&gpio0 RK_PC7 GPIO_ACTIVE_HIGH>;
+		vin-supply = <&vcc3v3_sys>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vcc3v3_lcd0_n_en>;
 
 		regulator-state-mem {
 			regulator-off-in-suspend;
@@ -66,7 +146,13 @@
 	vcc3v3_lcd1_n: vcc3v3-lcd1-n {
 		compatible = "regulator-fixed";
 		regulator-name = "vcc3v3_lcd1_n";
-		regulator-boot-on;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		enable-active-high;
+		gpio = <&gpio0 RK_PC5 GPIO_ACTIVE_HIGH>;
+		vin-supply = <&vcc3v3_sys>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vcc3v3_lcd1_n_en>;
 
 		regulator-state-mem {
 			regulator-off-in-suspend;
@@ -74,6 +160,30 @@
 	};
 };
 
+&combphy0 {
+	status = "okay";
+};
+
+&combphy1 {
+	status = "okay";
+};
+
+&cpu0 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&cpu1 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&cpu2 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&cpu3 {
+	cpu-supply = <&vdd_cpu>;
+};
+
 &gmac0 {
 	assigned-clocks = <&cru SCLK_GMAC0_RX_TX>, <&cru SCLK_GMAC0>;
 	assigned-clock-parents = <&cru SCLK_GMAC0_RGMII_SPEED>;
@@ -106,18 +216,67 @@
 	status = "okay";
 };
 
+&gpu {
+	mali-supply = <&vdd_gpu>;
+	status = "okay";
+};
+
+&hdmi {
+	avdd-0v9-supply = <&vdda0v9_image>;
+	avdd-1v8-supply = <&vcca1v8_image>;
+	status = "okay";
+};
+
+&hdmi_in {
+	hdmi_in_vp0: endpoint {
+		remote-endpoint = <&vp0_out_hdmi>;
+	};
+};
+
+&hdmi_out {
+	hdmi_out_con: endpoint {
+		remote-endpoint = <&hdmi_con_in>;
+	};
+};
+
+&hdmi_sound {
+	status = "okay";
+};
+
 &i2c0 {
 	status = "okay";
 
+	vdd_cpu: regulator@1c {
+		compatible = "tcs,tcs4525";
+		reg = <0x1c>;
+		fcs,suspend-voltage-selector = <1>;
+		regulator-name = "vdd_cpu";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <800000>;
+		regulator-max-microvolt = <1150000>;
+		regulator-ramp-delay = <2300>;
+		vin-supply = <&vcc5v0_sys>;
+
+		regulator-state-mem {
+			regulator-off-in-suspend;
+		};
+	};
+
 	rk809: pmic@20 {
 		compatible = "rockchip,rk809";
 		reg = <0x20>;
 		interrupt-parent = <&gpio0>;
 		interrupts = <RK_PA3 IRQ_TYPE_LEVEL_LOW>;
+		assigned-clocks = <&cru I2S1_MCLKOUT_TX>;
+		assigned-clock-parents = <&cru CLK_I2S1_8CH_TX>;
 		#clock-cells = <1>;
+		clock-names = "mclk";
+		clocks = <&cru I2S1_MCLKOUT_TX>;
 		pinctrl-names = "default";
-		pinctrl-0 = <&pmic_int>;
+		pinctrl-0 = <&pmic_int>, <&i2s1m0_mclk>;
 		rockchip,system-power-controller;
+		#sound-dai-cells = <0>;
 		vcc1-supply = <&vcc3v3_sys>;
 		vcc2-supply = <&vcc3v3_sys>;
 		vcc3-supply = <&vcc3v3_sys>;
@@ -147,6 +306,7 @@
 
 			vdd_gpu: DCDC_REG2 {
 				regulator-name = "vdd_gpu";
+				regulator-always-on;
 				regulator-init-microvolt = <900000>;
 				regulator-initial-mode = <0x2>;
 				regulator-min-microvolt = <500000>;
@@ -231,6 +391,7 @@
 
 			vccio_acodec: LDO_REG4 {
 				regulator-name = "vccio_acodec";
+				regulator-always-on;
 				regulator-min-microvolt = <3300000>;
 				regulator-max-microvolt = <3300000>;
 
@@ -315,9 +476,39 @@
 				};
 			};
 		};
+
+		codec {
+			mic-in-differential;
+		};
+	};
+};
+
+&i2c1 {
+	status = "okay";
+
+	touchscreen0: goodix@14 {
+		compatible = "goodix,gt1151";
+		reg = <0x14>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <RK_PB5 IRQ_TYPE_EDGE_FALLING>;
+		AVDD28-supply = <&vcc3v3_lcd0_n>;
+		irq-gpios = <&gpio0 RK_PB5 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&touch_int &touch_rst>;
+		reset-gpios = <&gpio0 RK_PB6 GPIO_ACTIVE_HIGH>;
+		VDDIO-supply = <&vcc3v3_lcd0_n>;
 	};
 };
 
+&i2s0_8ch {
+	status = "okay";
+};
+
+&i2s1_8ch {
+	rockchip,trcm-sync-tx-only;
+	status = "okay";
+};
+
 &mdio0 {
 	rgmii_phy0: ethernet-phy@0 {
 		compatible = "ethernet-phy-ieee802.3-c22";
@@ -339,12 +530,45 @@
 };
 
 &pinctrl {
+	display {
+		vcc3v3_lcd0_n_en: vcc3v3_lcd0_n_en {
+			rockchip,pins = <0 RK_PC7 0 &pcfg_pull_none>;
+		};
+		vcc3v3_lcd1_n_en: vcc3v3_lcd1_n_en {
+			rockchip,pins = <0 RK_PC5 0 &pcfg_pull_none>;
+		};
+	};
+
+	leds {
+		led_work_en: led_work_en {
+			rockchip,pins = <0 RK_PC0 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
 	pmic {
 		pmic_int: pmic_int {
 			rockchip,pins =
 				<0 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>;
 		};
 	};
+
+	touchscreen {
+		touch_int: touch_int {
+			rockchip,pins = <0 RK_PB5 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+		touch_rst: touch_rst {
+			rockchip,pins = <0 RK_PB6 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	usb {
+		vcc5v0_usb_host_en: vcc5v0_usb_host_en {
+			rockchip,pins = <0 RK_PA6 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+		vcc5v0_usb_otg_en: vcc5v0_usb_otg_en {
+			rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
 };
 
 &pmu_io_domains {
@@ -387,6 +611,82 @@
 	status = "okay";
 };
 
+&tsadc {
+	rockchip,hw-tshut-mode = <1>;
+	rockchip,hw-tshut-polarity = <0>;
+	status = "okay";
+};
+
 &uart2 {
 	status = "okay";
 };
+
+&usb_host0_ehci {
+	status = "okay";
+};
+
+&usb_host0_ohci {
+	status = "okay";
+};
+
+&usb_host0_xhci {
+	extcon = <&usb2phy0>;
+	status = "okay";
+};
+
+&usb_host1_ehci {
+	status = "okay";
+};
+
+&usb_host1_ohci {
+	status = "okay";
+};
+
+&usb_host1_xhci {
+	status = "okay";
+};
+
+&usb2phy0 {
+	status = "okay";
+};
+
+&usb2phy0_host {
+	phy-supply = <&vcc5v0_usb_host>;
+	status = "okay";
+};
+
+&usb2phy0_otg {
+	phy-supply = <&vcc5v0_usb_otg>;
+	status = "okay";
+};
+
+&usb2phy1 {
+	status = "okay";
+};
+
+&usb2phy1_host {
+	phy-supply = <&vcc5v0_usb_host>;
+	status = "okay";
+};
+
+&usb2phy1_otg {
+	phy-supply = <&vcc5v0_usb_host>;
+	status = "okay";
+};
+
+&vop {
+	assigned-clocks = <&cru DCLK_VOP0>, <&cru DCLK_VOP1>;
+	assigned-clock-parents = <&pmucru PLL_HPLL>, <&cru PLL_VPLL>;
+	status = "okay";
+};
+
+&vop_mmu {
+	status = "okay";
+};
+
+&vp0 {
+	vp0_out_hdmi: endpoint@ROCKCHIP_VOP2_EP_HDMI0 {
+		reg = <ROCKCHIP_VOP2_EP_HDMI0>;
+		remote-endpoint = <&hdmi_in_vp0>;
+	};
+};
diff --git a/arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts b/arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts
new file mode 100644
index 000000000000..fb87a168fe96
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3568-rock-3a.dts
@@ -0,0 +1,730 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/rockchip.h>
+#include <dt-bindings/soc/rockchip,vop2.h>
+#include "rk3568.dtsi"
+
+/ {
+	model = "Radxa ROCK3 Model A";
+	compatible = "radxa,rock3a", "rockchip,rk3568";
+
+	aliases {
+		ethernet0 = &gmac1;
+		mmc0 = &sdmmc0;
+		mmc1 = &sdhci;
+	};
+
+	chosen: chosen {
+		stdout-path = "serial2:1500000n8";
+	};
+
+	hdmi-con {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con_in: endpoint {
+				remote-endpoint = <&hdmi_out_con>;
+			};
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led_user: led-0 {
+			gpios = <&gpio0 RK_PB7 GPIO_ACTIVE_HIGH>;
+			function = LED_FUNCTION_HEARTBEAT;
+			color = <LED_COLOR_ID_BLUE>;
+			linux,default-trigger = "heartbeat";
+			pinctrl-names = "default";
+			pinctrl-0 = <&led_user_en>;
+		};
+	};
+
+	rk809-sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,format = "i2s";
+		simple-audio-card,name = "Analog RK809";
+		simple-audio-card,mclk-fs = <256>;
+
+		simple-audio-card,cpu {
+			sound-dai = <&i2s1_8ch>;
+		};
+
+		simple-audio-card,codec {
+			sound-dai = <&rk809>;
+		};
+	};
+
+	vcc12v_dcin: vcc12v-dcin {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc12v_dcin";
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vcc3v3_pcie: vcc3v3-pcie-regulator {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpios = <&gpio0 RK_PD4 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pcie_enable_h>;
+		regulator-name = "vcc3v3_pcie";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc5v0_sys>;
+	};
+
+	vcc3v3_sys: vcc3v3-sys {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3_sys";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc12v_dcin>;
+	};
+
+	vcc5v0_sys: vcc5v0-sys {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc5v0_sys";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc12v_dcin>;
+	};
+
+	vcc5v0_usb: vcc5v0-usb {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc5v0_usb";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc12v_dcin>;
+	};
+
+	vcc5v0_usb_host: vcc5v0-usb-host {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio0 RK_PA6 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vcc5v0_usb_host_en>;
+		regulator-name = "vcc5v0_usb_host";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc5v0_usb>;
+	};
+
+	vcc5v0_usb_hub: vcc5v0-usb-hub-regulator {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio0 RK_PD5 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vcc5v0_usb_hub_en>;
+		regulator-name = "vcc5v0_usb_hub";
+		regulator-always-on;
+		vin-supply = <&vcc5v0_usb>;
+	};
+
+	vcc5v0_usb_otg: vcc5v0-usb-otg-regulator {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio0 RK_PA5 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vcc5v0_usb_otg_en>;
+		regulator-name = "vcc5v0_usb_otg";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc5v0_usb>;
+	};
+
+	vcc_cam: vcc-cam {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio1 RK_PB1 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vcc_cam_en>;
+		regulator-name = "vcc_cam";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc3v3_sys>;
+
+		regulator-state-mem {
+			regulator-off-in-suspend;
+		};
+	};
+
+	vcc_mipi: vcc-mipi {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&gpio3 RK_PC0 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vcc_mipi_en>;
+		regulator-name = "vcc_mipi";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc3v3_sys>;
+
+		regulator-state-mem {
+			regulator-off-in-suspend;
+		};
+	};
+};
+
+&combphy0 {
+	status = "okay";
+};
+
+&combphy1 {
+	status = "okay";
+};
+
+&combphy2 {
+	status = "okay";
+};
+
+&cpu0 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&cpu1 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&cpu2 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&cpu3 {
+	cpu-supply = <&vdd_cpu>;
+};
+
+&gmac1 {
+	assigned-clocks = <&cru SCLK_GMAC1_RX_TX>, <&cru SCLK_GMAC1>;
+	assigned-clock-parents = <&cru SCLK_GMAC1_RGMII_SPEED>;
+	assigned-clock-rates = <0>, <125000000>;
+	clock_in_out = "output";
+	phy-handle = <&rgmii_phy1>;
+	phy-mode = "rgmii-id";
+	pinctrl-names = "default";
+	pinctrl-0 = <&gmac1m1_miim
+		     &gmac1m1_tx_bus2
+		     &gmac1m1_rx_bus2
+		     &gmac1m1_rgmii_clk
+		     &gmac1m1_rgmii_bus>;
+	status = "okay";
+};
+
+&gpu {
+	mali-supply = <&vdd_gpu>;
+	status = "okay";
+};
+
+&hdmi {
+	avdd-0v9-supply = <&vdda0v9_image>;
+	avdd-1v8-supply = <&vcca1v8_image>;
+	status = "okay";
+};
+
+&hdmi_in {
+	hdmi_in_vp0: endpoint {
+		remote-endpoint = <&vp0_out_hdmi>;
+	};
+};
+
+&hdmi_out {
+	hdmi_out_con: endpoint {
+		remote-endpoint = <&hdmi_con_in>;
+	};
+};
+
+&hdmi_sound {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	vdd_cpu: regulator@1c {
+		compatible = "tcs,tcs4525";
+		reg = <0x1c>;
+		fcs,suspend-voltage-selector = <1>;
+		regulator-name = "vdd_cpu";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <800000>;
+		regulator-max-microvolt = <1150000>;
+		regulator-ramp-delay = <2300>;
+		vin-supply = <&vcc5v0_sys>;
+
+		regulator-state-mem {
+			regulator-off-in-suspend;
+		};
+	};
+
+	rk809: pmic@20 {
+		compatible = "rockchip,rk809";
+		reg = <0x20>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <RK_PA3 IRQ_TYPE_LEVEL_LOW>;
+		assigned-clocks = <&cru I2S1_MCLKOUT_TX>;
+		assigned-clock-parents = <&cru CLK_I2S1_8CH_TX>;
+		#clock-cells = <1>;
+		clock-names = "mclk";
+		clocks = <&cru I2S1_MCLKOUT_TX>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_int>, <&i2s1m0_mclk>;
+		rockchip,system-power-controller;
+		#sound-dai-cells = <0>;
+		vcc1-supply = <&vcc3v3_sys>;
+		vcc2-supply = <&vcc3v3_sys>;
+		vcc3-supply = <&vcc3v3_sys>;
+		vcc4-supply = <&vcc3v3_sys>;
+		vcc5-supply = <&vcc3v3_sys>;
+		vcc6-supply = <&vcc3v3_sys>;
+		vcc7-supply = <&vcc3v3_sys>;
+		vcc8-supply = <&vcc3v3_sys>;
+		vcc9-supply = <&vcc3v3_sys>;
+		wakeup-source;
+
+		regulators {
+			vdd_logic: DCDC_REG1 {
+				regulator-name = "vdd_logic";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-init-microvolt = <900000>;
+				regulator-initial-mode = <0x2>;
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-ramp-delay = <6001>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdd_gpu: DCDC_REG2 {
+				regulator-name = "vdd_gpu";
+				regulator-always-on;
+				regulator-init-microvolt = <900000>;
+				regulator-initial-mode = <0x2>;
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-ramp-delay = <6001>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_ddr: DCDC_REG3 {
+				regulator-name = "vcc_ddr";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-initial-mode = <0x2>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vdd_npu: DCDC_REG4 {
+				regulator-name = "vdd_npu";
+				regulator-init-microvolt = <900000>;
+				regulator-initial-mode = <0x2>;
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <1350000>;
+				regulator-ramp-delay = <6001>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_1v8: DCDC_REG5 {
+				regulator-name = "vcc_1v8";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdda0v9_image: LDO_REG1 {
+				regulator-name = "vdda0v9_image";
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <900000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdda_0v9: LDO_REG2 {
+				regulator-name = "vdda_0v9";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <900000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdda0v9_pmu: LDO_REG3 {
+				regulator-name = "vdda0v9_pmu";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <900000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <900000>;
+				};
+			};
+
+			vccio_acodec: LDO_REG4 {
+				regulator-name = "vccio_acodec";
+				regulator-always-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vccio_sd: LDO_REG5 {
+				regulator-name = "vccio_sd";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc3v3_pmu: LDO_REG6 {
+				regulator-name = "vcc3v3_pmu";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+				};
+			};
+
+			vcca_1v8: LDO_REG7 {
+				regulator-name = "vcca_1v8";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcca1v8_pmu: LDO_REG8 {
+				regulator-name = "vcca1v8_pmu";
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vcca1v8_image: LDO_REG9 {
+				regulator-name = "vcca1v8_image";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_3v3: SWITCH_REG1 {
+				regulator-name = "vcc_3v3";
+				regulator-always-on;
+				regulator-boot-on;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc3v3_sd: SWITCH_REG2 {
+				regulator-name = "vcc3v3_sd";
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+		};
+
+		codec {
+			mic-in-differential;
+		};
+	};
+};
+
+&i2c3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c3m1_xfer>;
+	status = "disabled";
+};
+
+&i2c4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c4m1_xfer>;
+	status = "disabled";
+};
+
+&i2c5 {
+	status = "okay";
+
+	hym8563: rtc@51 {
+		compatible = "haoyu,hym8563";
+		reg = <0x51>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <RK_PD3 IRQ_TYPE_LEVEL_LOW>;
+		#clock-cells = <0>;
+		clock-frequency = <32768>;
+		clock-output-names = "rtcic_32kout";
+		pinctrl-names = "default";
+		pinctrl-0 = <&hym8563_int>;
+		wakeup-source;
+	};
+};
+
+&i2s0_8ch {
+	status = "okay";
+};
+
+&i2s1_8ch {
+	rockchip,trcm-sync-tx-only;
+	status = "okay";
+};
+
+&mdio1 {
+	rgmii_phy1: ethernet-phy@0 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0x0>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&eth_phy_rst>;
+		reset-assert-us = <20000>;
+		reset-deassert-us = <100000>;
+		reset-gpios = <&gpio3 RK_PB0 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&pcie2x1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie_reset_h>;
+	reset-gpios = <&gpio3 RK_PC1 GPIO_ACTIVE_HIGH>;
+	vpcie3v3-supply = <&vcc3v3_pcie>;
+	status = "okay";
+};
+
+&pinctrl {
+	cam {
+		vcc_cam_en: vcc_cam_en {
+			rockchip,pins = <1 RK_PB1 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	display {
+		vcc_mipi_en: vcc_mipi_en {
+			rockchip,pins = <3 RK_PC0 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	ethernet {
+		eth_phy_rst: eth_phy_rst {
+			rockchip,pins = <3 RK_PB0 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	hym8563 {
+		hym8563_int: hym8563-int {
+			rockchip,pins = <0 RK_PD3 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	leds {
+		led_user_en: led_user_en {
+			rockchip,pins = <0 RK_PB7 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	pcie {
+		pcie_enable_h: pcie-enable-h {
+			rockchip,pins = <0 RK_PD4 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		pcie_reset_h: pcie-reset-h {
+			rockchip,pins = <3 RK_PC1 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	pmic {
+		pmic_int: pmic_int {
+			rockchip,pins =
+				<0 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	usb {
+		vcc5v0_usb_host_en: vcc5v0_usb_host_en {
+			rockchip,pins = <0 RK_PA6 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+		vcc5v0_usb_hub_en: vcc5v0_usb_hub_en {
+			rockchip,pins = <0 RK_PD5 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+		vcc5v0_usb_otg_en: vcc5v0_usb_otg_en {
+			rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+};
+
+&pmu_io_domains {
+	pmuio1-supply = <&vcc3v3_pmu>;
+	pmuio2-supply = <&vcc3v3_pmu>;
+	vccio1-supply = <&vccio_acodec>;
+	vccio2-supply = <&vcc_1v8>;
+	vccio3-supply = <&vccio_sd>;
+	vccio4-supply = <&vcc_1v8>;
+	vccio5-supply = <&vcc_3v3>;
+	vccio6-supply = <&vcc_1v8>;
+	vccio7-supply = <&vcc_3v3>;
+	status = "okay";
+};
+
+&saradc {
+	vref-supply = <&vcca_1v8>;
+	status = "okay";
+};
+
+&sdhci {
+	bus-width = <8>;
+	max-frequency = <200000000>;
+	non-removable;
+	pinctrl-names = "default";
+	pinctrl-0 = <&emmc_bus8 &emmc_clk &emmc_cmd &emmc_datastrobe>;
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&vcc_1v8>;
+	status = "okay";
+};
+
+&sdmmc0 {
+	bus-width = <4>;
+	cap-sd-highspeed;
+	cd-gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_LOW>;
+	disable-wp;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc0_bus4 &sdmmc0_clk &sdmmc0_cmd &sdmmc0_det>;
+	sd-uhs-sdr104;
+	vmmc-supply = <&vcc3v3_sd>;
+	vqmmc-supply = <&vccio_sd>;
+	status = "okay";
+};
+
+&tsadc {
+	rockchip,hw-tshut-mode = <1>;
+	rockchip,hw-tshut-polarity = <0>;
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&usb_host0_ehci {
+	status = "okay";
+};
+
+&usb_host0_ohci {
+	status = "okay";
+};
+
+&usb_host0_xhci {
+	extcon = <&usb2phy0>;
+	status = "okay";
+};
+
+&usb_host1_ehci {
+	status = "okay";
+};
+
+&usb_host1_ohci {
+	status = "okay";
+};
+
+&usb_host1_xhci {
+	status = "okay";
+};
+
+&usb2phy0 {
+	status = "okay";
+};
+
+&usb2phy0_host {
+	phy-supply = <&vcc5v0_usb_host>;
+	status = "okay";
+};
+
+&usb2phy0_otg {
+	phy-supply = <&vcc5v0_usb_otg>;
+	status = "okay";
+};
+
+&usb2phy1 {
+	status = "okay";
+};
+
+&usb2phy1_host {
+	phy-supply = <&vcc5v0_usb_host>;
+	status = "okay";
+};
+
+&usb2phy1_otg {
+	phy-supply = <&vcc5v0_usb_host>;
+	status = "okay";
+};
+
+&vop {
+	assigned-clocks = <&cru DCLK_VOP0>, <&cru DCLK_VOP1>;
+	assigned-clock-parents = <&pmucru PLL_HPLL>, <&cru PLL_VPLL>;
+	status = "okay";
+};
+
+&vop_mmu {
+	status = "okay";
+};
+
+&vp0 {
+	vp0_out_hdmi: endpoint@ROCKCHIP_VOP2_EP_HDMI0 {
+		reg = <ROCKCHIP_VOP2_EP_HDMI0>;
+		remote-endpoint = <&hdmi_in_vp0>;
+	};
+};
diff --git a/arch/arm64/boot/dts/rockchip/rk3568.dtsi b/arch/arm64/boot/dts/rockchip/rk3568.dtsi
index 2fd313a295f8..ba67b58f05b7 100644
--- a/arch/arm64/boot/dts/rockchip/rk3568.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3568.dtsi
@@ -8,6 +8,25 @@
 / {
 	compatible = "rockchip,rk3568";
 
+	sata0: sata@fc000000 {
+		compatible = "rockchip,rk3568-dwc-ahci", "snps,dwc-ahci";
+		reg = <0 0xfc000000 0 0x1000>;
+		clocks = <&cru ACLK_SATA0>, <&cru CLK_SATA0_PMALIVE>,
+			 <&cru CLK_SATA0_RXOOB>;
+		clock-names = "sata", "pmalive", "rxoob";
+		interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>;
+		phys = <&combphy0 PHY_TYPE_SATA>;
+		phy-names = "sata-phy";
+		ports-implemented = <0x1>;
+		power-domains = <&power RK3568_PD_PIPE>;
+		status = "disabled";
+	};
+
+	pipe_phy_grf0: syscon@fdc70000 {
+		compatible = "rockchip,rk3568-pipe-phy-grf", "syscon";
+		reg = <0x0 0xfdc70000 0x0 0x1000>;
+	};
+
 	qos_pcie3x1: qos@fe190080 {
 		compatible = "rockchip,rk3568-qos", "syscon";
 		reg = <0x0 0xfe190080 0x0 0x20>;
@@ -23,6 +42,128 @@
 		reg = <0x0 0xfe190200 0x0 0x20>;
 	};
 
+	pcie30_phy_grf: syscon@fdcb8000 {
+		compatible = "rockchip,rk3568-pcie3-phy-grf", "syscon";
+		reg = <0x0 0xfdcb8000 0x0 0x10000>;
+	};
+
+	pcie30phy: phy@fe8c0000 {
+		compatible = "rockchip,rk3568-pcie3-phy";
+		reg = <0x0 0xfe8c0000 0x0 0x20000>;
+		#phy-cells = <0>;
+		clocks = <&pmucru CLK_PCIE30PHY_REF_M>, <&pmucru CLK_PCIE30PHY_REF_N>,
+			 <&cru PCLK_PCIE30PHY>;
+		clock-names = "refclk_m", "refclk_n", "pclk";
+		resets = <&cru SRST_PCIE30PHY>;
+		reset-names = "phy";
+		rockchip,phy-grf = <&pcie30_phy_grf>;
+		status = "disabled";
+	};
+
+	pcie3x1: pcie@fe270000 {
+		compatible = "rockchip,rk3568-pcie";
+		#address-cells = <3>;
+		#size-cells = <2>;
+		bus-range = <0x0 0xf>;
+		clocks = <&cru ACLK_PCIE30X1_MST>, <&cru ACLK_PCIE30X1_SLV>,
+			 <&cru ACLK_PCIE30X1_DBI>, <&cru PCLK_PCIE30X1>,
+			 <&cru CLK_PCIE30X1_AUX_NDFT>;
+		clock-names = "aclk_mst", "aclk_slv",
+			      "aclk_dbi", "pclk", "aux";
+		device_type = "pci";
+		interrupts = <GIC_SPI 160 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 159 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 158 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 156 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "sys", "pmc", "msg", "legacy", "err";
+		#interrupt-cells = <1>;
+		interrupt-map-mask = <0 0 0 7>;
+		interrupt-map = <0 0 0 1 &pcie3x1_intc 0>,
+				<0 0 0 2 &pcie3x1_intc 1>,
+				<0 0 0 3 &pcie3x1_intc 2>,
+				<0 0 0 4 &pcie3x1_intc 3>;
+		linux,pci-domain = <1>;
+		num-ib-windows = <6>;
+		num-ob-windows = <2>;
+		max-link-speed = <3>;
+		msi-map = <0x0 &gic 0x1000 0x1000>;
+		num-lanes = <1>;
+		phys = <&pcie30phy>;
+		phy-names = "pcie-phy";
+		power-domains = <&power RK3568_PD_PIPE>;
+		reg = <0x3 0xc0400000 0x0 0x00400000>,
+		      <0x0 0xfe270000 0x0 0x00010000>,
+		      <0x3 0x7f000000 0x0 0x01000000>;
+		ranges = <0x01000000 0x0 0x3ef00000 0x3 0x7ef00000 0x0 0x00100000>,
+			 <0x02000000 0x0 0x00000000 0x3 0x40000000 0x0 0x3ef00000>;
+		reg-names = "dbi", "apb", "config";
+		resets = <&cru SRST_PCIE30X1_POWERUP>;
+		reset-names = "pipe";
+		/* bifurcation; lane1 when using 1+1 */
+		status = "disabled";
+
+		pcie3x1_intc: legacy-interrupt-controller {
+			interrupt-controller;
+			#address-cells = <0>;
+			#interrupt-cells = <1>;
+			interrupt-parent = <&gic>;
+			interrupts = <GIC_SPI 157 IRQ_TYPE_EDGE_RISING>;
+		};
+	};
+
+	pcie3x2: pcie@fe280000 {
+		compatible = "rockchip,rk3568-pcie";
+		#address-cells = <3>;
+		#size-cells = <2>;
+		bus-range = <0x0 0xf>;
+		clocks = <&cru ACLK_PCIE30X2_MST>, <&cru ACLK_PCIE30X2_SLV>,
+			 <&cru ACLK_PCIE30X2_DBI>, <&cru PCLK_PCIE30X2>,
+			 <&cru CLK_PCIE30X2_AUX_NDFT>;
+		clock-names = "aclk_mst", "aclk_slv",
+			      "aclk_dbi", "pclk", "aux";
+		device_type = "pci";
+		interrupts = <GIC_SPI 165 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 164 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 163 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 161 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "sys", "pmc", "msg", "legacy", "err";
+		#interrupt-cells = <1>;
+		interrupt-map-mask = <0 0 0 7>;
+		interrupt-map = <0 0 0 1 &pcie3x2_intc 0>,
+				<0 0 0 2 &pcie3x2_intc 1>,
+				<0 0 0 3 &pcie3x2_intc 2>,
+				<0 0 0 4 &pcie3x2_intc 3>;
+		linux,pci-domain = <2>;
+		num-ib-windows = <6>;
+		num-ob-windows = <2>;
+		max-link-speed = <3>;
+		msi-map = <0x0 &gic 0x2000 0x1000>;
+		num-lanes = <2>;
+		phys = <&pcie30phy>;
+		phy-names = "pcie-phy";
+		power-domains = <&power RK3568_PD_PIPE>;
+		reg = <0x3 0xc0800000 0x0 0x00400000>,
+		      <0x0 0xfe280000 0x0 0x00010000>,
+		      <0x3 0xbf000000 0x0 0x01000000>;
+		ranges = <0x01000000 0x0 0x3ef00000 0x3 0xbef00000 0x0 0x00100000>,
+			 <0x02000000 0x0 0x00000000 0x3 0x80000000 0x0 0x3ef00000>;
+		reg-names = "dbi", "apb", "config";
+		resets = <&cru SRST_PCIE30X2_POWERUP>;
+		reset-names = "pipe";
+		/* bifurcation; lane0 when using 1+1 */
+		status = "disabled";
+
+		pcie3x2_intc: legacy-interrupt-controller {
+			interrupt-controller;
+			#address-cells = <0>;
+			#interrupt-cells = <1>;
+			interrupt-parent = <&gic>;
+			interrupts = <GIC_SPI 162 IRQ_TYPE_EDGE_RISING>;
+		};
+	};
+
 	gmac0: ethernet@fe2a0000 {
 		compatible = "rockchip,rk3568-gmac", "snps,dwmac-4.20a";
 		reg = <0x0 0xfe2a0000 0x0 0x10000>;
@@ -32,13 +173,11 @@
 		clocks = <&cru SCLK_GMAC0>, <&cru SCLK_GMAC0_RX_TX>,
 			 <&cru SCLK_GMAC0_RX_TX>, <&cru CLK_MAC0_REFOUT>,
 			 <&cru ACLK_GMAC0>, <&cru PCLK_GMAC0>,
-			 <&cru SCLK_GMAC0_RX_TX>, <&cru CLK_GMAC0_PTP_REF>,
-			 <&cru PCLK_XPCS>;
+			 <&cru SCLK_GMAC0_RX_TX>, <&cru CLK_GMAC0_PTP_REF>;
 		clock-names = "stmmaceth", "mac_clk_rx",
 			      "mac_clk_tx", "clk_mac_refout",
 			      "aclk_mac", "pclk_mac",
-			      "clk_mac_speed", "ptp_ref",
-			      "pclk_xpcs";
+			      "clk_mac_speed", "ptp_ref";
 		resets = <&cru SRST_A_GMAC0>;
 		reset-names = "stmmaceth";
 		rockchip,grf = <&grf>;
@@ -71,6 +210,22 @@
 			queue0 {};
 		};
 	};
+
+	combphy0: phy@fe820000 {
+		compatible = "rockchip,rk3568-naneng-combphy";
+		reg = <0x0 0xfe820000 0x0 0x100>;
+		clocks = <&pmucru CLK_PCIEPHY0_REF>,
+			 <&cru PCLK_PIPEPHY0>,
+			 <&cru PCLK_PIPE>;
+		clock-names = "ref", "apb", "pipe";
+		assigned-clocks = <&pmucru CLK_PCIEPHY0_REF>;
+		assigned-clock-rates = <100000000>;
+		resets = <&cru SRST_PIPEPHY0>;
+		rockchip,pipe-grf = <&pipegrf>;
+		rockchip,pipe-phy-grf = <&pipe_phy_grf0>;
+		#phy-cells = <1>;
+		status = "disabled";
+	};
 };
 
 &cpu0_opp_table {
@@ -80,6 +235,10 @@
 	};
 };
 
+&pipegrf {
+	compatible = "rockchip,rk3568-pipe-grf", "syscon";
+};
+
 &power {
 	power-domain@RK3568_PD_PIPE {
 		reg = <RK3568_PD_PIPE>;
@@ -95,3 +254,12 @@
 		#power-domain-cells = <0>;
 	};
 };
+
+&usb_host0_xhci {
+	phys = <&usb2phy0_otg>, <&combphy0 PHY_TYPE_USB3>;
+	phy-names = "usb2-phy", "usb3-phy";
+};
+
+&vop {
+	compatible = "rockchip,rk3568-vop";
+};
diff --git a/arch/arm64/boot/dts/rockchip/rk356x.dtsi b/arch/arm64/boot/dts/rockchip/rk356x.dtsi
index 46d9552f6028..164708f1eb67 100644
--- a/arch/arm64/boot/dts/rockchip/rk356x.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk356x.dtsi
@@ -39,6 +39,10 @@
 		serial7 = &uart7;
 		serial8 = &uart8;
 		serial9 = &uart9;
+		spi0 = &spi0;
+		spi1 = &spi1;
+		spi2 = &spi2;
+		spi3 = &spi3;
 	};
 
 	cpus {
@@ -125,6 +129,11 @@
 		};
 	};
 
+	display_subsystem: display-subsystem {
+		compatible = "rockchip,display-subsystem";
+		ports = <&vop_out>;
+	};
+
 	firmware {
 		scmi: scmi {
 			compatible = "arm,scmi-smc";
@@ -140,6 +149,56 @@
 		};
 	};
 
+	gpu_opp_table: opp-table-1 {
+		compatible = "operating-points-v2";
+
+		opp-200000000 {
+			opp-hz = /bits/ 64 <200000000>;
+			opp-microvolt = <825000>;
+		};
+
+		opp-300000000 {
+			opp-hz = /bits/ 64 <300000000>;
+			opp-microvolt = <825000>;
+		};
+
+		opp-400000000 {
+			opp-hz = /bits/ 64 <400000000>;
+			opp-microvolt = <825000>;
+		};
+
+		opp-600000000 {
+			opp-hz = /bits/ 64 <600000000>;
+			opp-microvolt = <825000>;
+		};
+
+		opp-700000000 {
+			opp-hz = /bits/ 64 <700000000>;
+			opp-microvolt = <900000>;
+		};
+
+		opp-800000000 {
+			opp-hz = /bits/ 64 <800000000>;
+			opp-microvolt = <1000000>;
+		};
+	};
+
+	hdmi_sound: hdmi-sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "HDMI";
+		simple-audio-card,format = "i2s";
+		simple-audio-card,mclk-fs = <256>;
+		status = "disabled";
+
+		simple-audio-card,codec {
+			sound-dai = <&hdmi>;
+		};
+
+		simple-audio-card,cpu {
+			sound-dai = <&i2s0_8ch>;
+		};
+	};
+
 	pmu {
 		compatible = "arm,cortex-a55-pmu";
 		interrupts = <GIC_SPI 228 IRQ_TYPE_LEVEL_HIGH>,
@@ -192,6 +251,68 @@
 		};
 	};
 
+	sata1: sata@fc400000 {
+		compatible = "rockchip,rk3568-dwc-ahci", "snps,dwc-ahci";
+		reg = <0 0xfc400000 0 0x1000>;
+		clocks = <&cru ACLK_SATA1>, <&cru CLK_SATA1_PMALIVE>,
+			 <&cru CLK_SATA1_RXOOB>;
+		clock-names = "sata", "pmalive", "rxoob";
+		interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
+		phys = <&combphy1 PHY_TYPE_SATA>;
+		phy-names = "sata-phy";
+		ports-implemented = <0x1>;
+		power-domains = <&power RK3568_PD_PIPE>;
+		status = "disabled";
+	};
+
+	sata2: sata@fc800000 {
+		compatible = "rockchip,rk3568-dwc-ahci", "snps,dwc-ahci";
+		reg = <0 0xfc800000 0 0x1000>;
+		clocks = <&cru ACLK_SATA2>, <&cru CLK_SATA2_PMALIVE>,
+			 <&cru CLK_SATA2_RXOOB>;
+		clock-names = "sata", "pmalive", "rxoob";
+		interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+		phys = <&combphy2 PHY_TYPE_SATA>;
+		phy-names = "sata-phy";
+		ports-implemented = <0x1>;
+		power-domains = <&power RK3568_PD_PIPE>;
+		status = "disabled";
+	};
+
+	usb_host0_xhci: usb@fcc00000 {
+		compatible = "rockchip,rk3568-dwc3", "snps,dwc3";
+		reg = <0x0 0xfcc00000 0x0 0x400000>;
+		interrupts = <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru CLK_USB3OTG0_REF>, <&cru CLK_USB3OTG0_SUSPEND>,
+			 <&cru ACLK_USB3OTG0>;
+		clock-names = "ref_clk", "suspend_clk",
+			      "bus_clk";
+		dr_mode = "otg";
+		phy_type = "utmi_wide";
+		power-domains = <&power RK3568_PD_PIPE>;
+		resets = <&cru SRST_USB3OTG0>;
+		snps,dis_u2_susphy_quirk;
+		status = "disabled";
+	};
+
+	usb_host1_xhci: usb@fd000000 {
+		compatible = "rockchip,rk3568-dwc3", "snps,dwc3";
+		reg = <0x0 0xfd000000 0x0 0x400000>;
+		interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru CLK_USB3OTG1_REF>, <&cru CLK_USB3OTG1_SUSPEND>,
+			 <&cru ACLK_USB3OTG1>;
+		clock-names = "ref_clk", "suspend_clk",
+			      "bus_clk";
+		dr_mode = "host";
+		phys = <&usb2phy0_host>, <&combphy1 PHY_TYPE_USB3>;
+		phy-names = "usb2-phy", "usb3-phy";
+		phy_type = "utmi_wide";
+		power-domains = <&power RK3568_PD_PIPE>;
+		resets = <&cru SRST_USB3OTG1>;
+		snps,dis_u2_susphy_quirk;
+		status = "disabled";
+	};
+
 	gic: interrupt-controller@fd400000 {
 		compatible = "arm,gic-v3";
 		reg = <0x0 0xfd400000 0 0x10000>, /* GICD */
@@ -204,6 +325,50 @@
 		msi-controller;
 	};
 
+	usb_host0_ehci: usb@fd800000 {
+		compatible = "generic-ehci";
+		reg = <0x0 0xfd800000 0x0 0x40000>;
+		interrupts = <GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru HCLK_USB2HOST0>, <&cru HCLK_USB2HOST0_ARB>,
+			 <&cru PCLK_USB>;
+		phys = <&usb2phy1_otg>;
+		phy-names = "usb";
+		status = "disabled";
+	};
+
+	usb_host0_ohci: usb@fd840000 {
+		compatible = "generic-ohci";
+		reg = <0x0 0xfd840000 0x0 0x40000>;
+		interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru HCLK_USB2HOST0>, <&cru HCLK_USB2HOST0_ARB>,
+			 <&cru PCLK_USB>;
+		phys = <&usb2phy1_otg>;
+		phy-names = "usb";
+		status = "disabled";
+	};
+
+	usb_host1_ehci: usb@fd880000 {
+		compatible = "generic-ehci";
+		reg = <0x0 0xfd880000 0x0 0x40000>;
+		interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru HCLK_USB2HOST1>, <&cru HCLK_USB2HOST1_ARB>,
+			 <&cru PCLK_USB>;
+		phys = <&usb2phy1_host>;
+		phy-names = "usb";
+		status = "disabled";
+	};
+
+	usb_host1_ohci: usb@fd8c0000 {
+		compatible = "generic-ohci";
+		reg = <0x0 0xfd8c0000 0x0 0x40000>;
+		interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru HCLK_USB2HOST1>, <&cru HCLK_USB2HOST1_ARB>,
+			 <&cru PCLK_USB>;
+		phys = <&usb2phy1_host>;
+		phy-names = "usb";
+		status = "disabled";
+	};
+
 	pmugrf: syscon@fdc20000 {
 		compatible = "rockchip,rk3568-pmugrf", "syscon", "simple-mfd";
 		reg = <0x0 0xfdc20000 0x0 0x10000>;
@@ -214,11 +379,35 @@
 		};
 	};
 
+	pipegrf: syscon@fdc50000 {
+		reg = <0x0 0xfdc50000 0x0 0x1000>;
+	};
+
 	grf: syscon@fdc60000 {
 		compatible = "rockchip,rk3568-grf", "syscon", "simple-mfd";
 		reg = <0x0 0xfdc60000 0x0 0x10000>;
 	};
 
+	pipe_phy_grf1: syscon@fdc80000 {
+		compatible = "rockchip,rk3568-pipe-phy-grf", "syscon";
+		reg = <0x0 0xfdc80000 0x0 0x1000>;
+	};
+
+	pipe_phy_grf2: syscon@fdc90000 {
+		compatible = "rockchip,rk3568-pipe-phy-grf", "syscon";
+		reg = <0x0 0xfdc90000 0x0 0x1000>;
+	};
+
+	usb2phy0_grf: syscon@fdca0000 {
+		compatible = "rockchip,rk3568-usb2phy-grf", "syscon";
+		reg = <0x0 0xfdca0000 0x0 0x8000>;
+	};
+
+	usb2phy1_grf: syscon@fdca8000 {
+		compatible = "rockchip,rk3568-usb2phy-grf", "syscon";
+		reg = <0x0 0xfdca8000 0x0 0x8000>;
+	};
+
 	pmucru: clock-controller@fdd00000 {
 		compatible = "rockchip,rk3568-pmucru";
 		reg = <0x0 0xfdd00000 0x0 0x1000>;
@@ -229,6 +418,8 @@
 	cru: clock-controller@fdd20000 {
 		compatible = "rockchip,rk3568-cru";
 		reg = <0x0 0xfdd20000 0x0 0x1000>;
+		clocks = <&xin24m>;
+		clock-names = "xin24m";
 		#clock-cells = <1>;
 		#reset-cells = <1>;
 		assigned-clocks = <&cru PLL_GPLL>, <&pmucru PLL_PPLL>;
@@ -269,7 +460,7 @@
 		clocks = <&pmucru CLK_PWM0>, <&pmucru PCLK_PWM0>;
 		clock-names = "pwm", "pclk";
 		pinctrl-0 = <&pwm0m0_pins>;
-		pinctrl-names = "active";
+		pinctrl-names = "default";
 		#pwm-cells = <3>;
 		status = "disabled";
 	};
@@ -280,7 +471,7 @@
 		clocks = <&pmucru CLK_PWM0>, <&pmucru PCLK_PWM0>;
 		clock-names = "pwm", "pclk";
 		pinctrl-0 = <&pwm1m0_pins>;
-		pinctrl-names = "active";
+		pinctrl-names = "default";
 		#pwm-cells = <3>;
 		status = "disabled";
 	};
@@ -291,7 +482,7 @@
 		clocks = <&pmucru CLK_PWM0>, <&pmucru PCLK_PWM0>;
 		clock-names = "pwm", "pclk";
 		pinctrl-0 = <&pwm2m0_pins>;
-		pinctrl-names = "active";
+		pinctrl-names = "default";
 		#pwm-cells = <3>;
 		status = "disabled";
 	};
@@ -302,7 +493,7 @@
 		clocks = <&pmucru CLK_PWM0>, <&pmucru PCLK_PWM0>;
 		clock-names = "pwm", "pclk";
 		pinctrl-0 = <&pwm3_pins>;
-		pinctrl-names = "active";
+		pinctrl-names = "default";
 		#pwm-cells = <3>;
 		status = "disabled";
 	};
@@ -386,6 +577,61 @@
 		};
 	};
 
+	gpu: gpu@fde60000 {
+		compatible = "rockchip,rk3568-mali", "arm,mali-bifrost";
+		reg = <0x0 0xfde60000 0x0 0x4000>;
+		interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "job", "mmu", "gpu";
+		clocks = <&scmi_clk 1>, <&cru CLK_GPU>;
+		clock-names = "gpu", "bus";
+		#cooling-cells = <2>;
+		operating-points-v2 = <&gpu_opp_table>;
+		power-domains = <&power RK3568_PD_GPU>;
+		status = "disabled";
+	};
+
+	vpu: video-codec@fdea0400 {
+		compatible = "rockchip,rk3568-vpu";
+		reg = <0x0 0xfdea0000 0x0 0x800>;
+		interrupts = <GIC_SPI 139 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru ACLK_VPU>, <&cru HCLK_VPU>;
+		clock-names = "aclk", "hclk";
+		iommus = <&vdpu_mmu>;
+		power-domains = <&power RK3568_PD_VPU>;
+	};
+
+	vdpu_mmu: iommu@fdea0800 {
+		compatible = "rockchip,rk3568-iommu";
+		reg = <0x0 0xfdea0800 0x0 0x40>;
+		interrupts = <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
+		clock-names = "aclk", "iface";
+		clocks = <&cru ACLK_VPU>, <&cru HCLK_VPU>;
+		power-domains = <&power RK3568_PD_VPU>;
+		#iommu-cells = <0>;
+	};
+
+	vepu: video-codec@fdee0000 {
+		compatible = "rockchip,rk3568-vepu";
+		reg = <0x0 0xfdee0000 0x0 0x800>;
+		interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru ACLK_JENC>, <&cru HCLK_JENC>;
+		clock-names = "aclk", "hclk";
+		iommus = <&vepu_mmu>;
+		power-domains = <&power RK3568_PD_RGA>;
+	};
+
+	vepu_mmu: iommu@fdee0800 {
+		compatible = "rockchip,rk3568-iommu";
+		reg = <0x0 0xfdee0800 0x0 0x40>;
+		interrupts = <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru ACLK_JENC>, <&cru HCLK_JENC>;
+		clock-names = "aclk", "iface";
+		power-domains = <&power RK3568_PD_RGA>;
+		#iommu-cells = <0>;
+	};
+
 	sdmmc2: mmc@fe000000 {
 		compatible = "rockchip,rk3568-dw-mshc", "rockchip,rk3288-dw-mshc";
 		reg = <0x0 0xfe000000 0x0 0x4000>;
@@ -447,6 +693,140 @@
 		};
 	};
 
+	vop: vop@fe040000 {
+		reg = <0x0 0xfe040000 0x0 0x3000>, <0x0 0xfe044000 0x0 0x1000>;
+		reg-names = "vop", "gamma-lut";
+		interrupts = <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru ACLK_VOP>, <&cru HCLK_VOP>, <&cru DCLK_VOP0>,
+			 <&cru DCLK_VOP1>, <&cru DCLK_VOP2>;
+		clock-names = "aclk", "hclk", "dclk_vp0", "dclk_vp1", "dclk_vp2";
+		iommus = <&vop_mmu>;
+		power-domains = <&power RK3568_PD_VO>;
+		rockchip,grf = <&grf>;
+		status = "disabled";
+
+		vop_out: ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			vp0: port@0 {
+				reg = <0>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+
+			vp1: port@1 {
+				reg = <1>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+
+			vp2: port@2 {
+				reg = <2>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+	};
+
+	vop_mmu: iommu@fe043e00 {
+		compatible = "rockchip,rk3568-iommu";
+		reg = <0x0 0xfe043e00 0x0 0x100>, <0x0 0xfe043f00 0x0 0x100>;
+		interrupts = <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru ACLK_VOP>, <&cru HCLK_VOP>;
+		clock-names = "aclk", "iface";
+		#iommu-cells = <0>;
+		status = "disabled";
+	};
+
+	dsi0: dsi@fe060000 {
+		compatible = "rockchip,rk3568-mipi-dsi", "snps,dw-mipi-dsi";
+		reg = <0x00 0xfe060000 0x00 0x10000>;
+		interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>;
+		clock-names = "pclk", "hclk";
+		clocks = <&cru PCLK_DSITX_0>, <&cru HCLK_VO>;
+		phy-names = "dphy";
+		phys = <&dsi_dphy0>;
+		power-domains = <&power RK3568_PD_VO>;
+		reset-names = "apb";
+		resets = <&cru SRST_P_DSITX_0>;
+		rockchip,grf = <&grf>;
+		status = "disabled";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			dsi0_in: port@0 {
+				reg = <0>;
+			};
+
+			dsi0_out: port@1 {
+				reg = <1>;
+			};
+		};
+	};
+
+	dsi1: dsi@fe070000 {
+		compatible = "rockchip,rk3568-mipi-dsi", "snps,dw-mipi-dsi";
+		reg = <0x0 0xfe070000 0x0 0x10000>;
+		interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>;
+		clock-names = "pclk", "hclk";
+		clocks = <&cru PCLK_DSITX_1>, <&cru HCLK_VO>;
+		phy-names = "dphy";
+		phys = <&dsi_dphy1>;
+		power-domains = <&power RK3568_PD_VO>;
+		reset-names = "apb";
+		resets = <&cru SRST_P_DSITX_1>;
+		rockchip,grf = <&grf>;
+		status = "disabled";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			dsi1_in: port@0 {
+				reg = <0>;
+			};
+
+			dsi1_out: port@1 {
+				reg = <1>;
+			};
+		};
+	};
+
+	hdmi: hdmi@fe0a0000 {
+		compatible = "rockchip,rk3568-dw-hdmi";
+		reg = <0x0 0xfe0a0000 0x0 0x20000>;
+		interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru PCLK_HDMI_HOST>,
+			 <&cru CLK_HDMI_SFR>,
+			 <&cru CLK_HDMI_CEC>,
+			 <&pmucru CLK_HDMI_REF>,
+			 <&cru HCLK_VO>;
+		clock-names = "iahb", "isfr", "cec", "ref";
+		pinctrl-names = "default";
+		pinctrl-0 = <&hdmitx_scl &hdmitx_sda &hdmitxm0_cec>;
+		power-domains = <&power RK3568_PD_VO>;
+		reg-io-width = <4>;
+		rockchip,grf = <&grf>;
+		#sound-dai-cells = <0>;
+		status = "disabled";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			hdmi_in: port@0 {
+				reg = <0>;
+			};
+
+			hdmi_out: port@1 {
+				reg = <1>;
+			};
+		};
+	};
+
 	qos_gpu: qos@fe128000 {
 		compatible = "rockchip,rk3568-qos", "syscon";
 		reg = <0x0 0xfe128000 0x0 0x20>;
@@ -567,6 +947,56 @@
 		reg = <0x0 0xfe1a8100 0x0 0x20>;
 	};
 
+	pcie2x1: pcie@fe260000 {
+		compatible = "rockchip,rk3568-pcie";
+		reg = <0x3 0xc0000000 0x0 0x00400000>,
+		      <0x0 0xfe260000 0x0 0x00010000>,
+		      <0x3 0x3f000000 0x0 0x01000000>;
+		reg-names = "dbi", "apb", "config";
+		interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "sys", "pmc", "msi", "legacy", "err";
+		bus-range = <0x0 0xf>;
+		clocks = <&cru ACLK_PCIE20_MST>, <&cru ACLK_PCIE20_SLV>,
+			 <&cru ACLK_PCIE20_DBI>, <&cru PCLK_PCIE20>,
+			 <&cru CLK_PCIE20_AUX_NDFT>;
+		clock-names = "aclk_mst", "aclk_slv",
+			      "aclk_dbi", "pclk", "aux";
+		device_type = "pci";
+		interrupt-map-mask = <0 0 0 7>;
+		interrupt-map = <0 0 0 1 &pcie_intc 0>,
+				<0 0 0 2 &pcie_intc 1>,
+				<0 0 0 3 &pcie_intc 2>,
+				<0 0 0 4 &pcie_intc 3>;
+		linux,pci-domain = <0>;
+		num-ib-windows = <6>;
+		num-ob-windows = <2>;
+		max-link-speed = <2>;
+		msi-map = <0x0 &gic 0x0 0x1000>;
+		num-lanes = <1>;
+		phys = <&combphy2 PHY_TYPE_PCIE>;
+		phy-names = "pcie-phy";
+		power-domains = <&power RK3568_PD_PIPE>;
+		ranges = <0x01000000 0x0 0x3ef00000 0x3 0x3ef00000 0x0 0x00100000
+			  0x02000000 0x0 0x00000000 0x3 0x00000000 0x0 0x3ef00000>;
+		resets = <&cru SRST_PCIE20_POWERUP>;
+		reset-names = "pipe";
+		#address-cells = <3>;
+		#size-cells = <2>;
+		status = "disabled";
+
+		pcie_intc: legacy-interrupt-controller {
+			#address-cells = <0>;
+			#interrupt-cells = <1>;
+			interrupt-controller;
+			interrupt-parent = <&gic>;
+			interrupts = <GIC_SPI 72 IRQ_TYPE_EDGE_RISING>;
+		};
+	};
+
 	sdmmc0: mmc@fe2b0000 {
 		compatible = "rockchip,rk3568-dw-mshc", "rockchip,rk3288-dw-mshc";
 		reg = <0x0 0xfe2b0000 0x0 0x4000>;
@@ -595,6 +1025,17 @@
 		status = "disabled";
 	};
 
+	sfc: spi@fe300000 {
+		compatible = "rockchip,sfc";
+		reg = <0x0 0xfe300000 0x0 0x4000>;
+		interrupts = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru SCLK_SFC>, <&cru HCLK_SFC>;
+		clock-names = "clk_sfc", "hclk_sfc";
+		pinctrl-0 = <&fspi_pins>;
+		pinctrl-names = "default";
+		status = "disabled";
+	};
+
 	sdhci: mmc@fe310000 {
 		compatible = "rockchip,rk3568-dwcmshc";
 		reg = <0x0 0xfe310000 0x0 0x10000>;
@@ -622,6 +1063,23 @@
 		status = "disabled";
 	};
 
+	i2s0_8ch: i2s@fe400000 {
+		compatible = "rockchip,rk3568-i2s-tdm";
+		reg = <0x0 0xfe400000 0x0 0x1000>;
+		interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
+		assigned-clocks = <&cru CLK_I2S0_8CH_TX_SRC>, <&cru CLK_I2S0_8CH_RX_SRC>;
+		assigned-clock-rates = <1188000000>, <1188000000>;
+		clocks = <&cru MCLK_I2S0_8CH_TX>, <&cru MCLK_I2S0_8CH_RX>, <&cru HCLK_I2S0_8CH>;
+		clock-names = "mclk_tx", "mclk_rx", "hclk";
+		dmas = <&dmac1 0>;
+		dma-names = "tx";
+		resets = <&cru SRST_M_I2S0_8CH_TX>, <&cru SRST_M_I2S0_8CH_RX>;
+		reset-names = "tx-m", "rx-m";
+		rockchip,grf = <&grf>;
+		#sound-dai-cells = <0>;
+		status = "disabled";
+	};
+
 	i2s1_8ch: i2s@fe410000 {
 		compatible = "rockchip,rk3568-i2s-tdm";
 		reg = <0x0 0xfe410000 0x0 0x1000>;
@@ -647,7 +1105,44 @@
 		status = "disabled";
 	};
 
-	dmac0: dmac@fe530000 {
+	i2s3_2ch: i2s@fe430000 {
+		compatible = "rockchip,rk3568-i2s-tdm";
+		reg = <0x0 0xfe430000 0x0 0x1000>;
+		interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru MCLK_I2S3_2CH_TX>, <&cru MCLK_I2S3_2CH_RX>,
+			 <&cru HCLK_I2S3_2CH>;
+		clock-names = "mclk_tx", "mclk_rx", "hclk";
+		dmas = <&dmac1 6>, <&dmac1 7>;
+		dma-names = "tx", "rx";
+		resets = <&cru SRST_M_I2S3_2CH_TX>, <&cru SRST_M_I2S3_2CH_RX>;
+		reset-names = "tx-m", "rx-m";
+		rockchip,grf = <&grf>;
+		#sound-dai-cells = <0>;
+		status = "disabled";
+	};
+
+	pdm: pdm@fe440000 {
+		compatible = "rockchip,rk3568-pdm";
+		reg = <0x0 0xfe440000 0x0 0x1000>;
+		interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru MCLK_PDM>, <&cru HCLK_PDM>;
+		clock-names = "pdm_clk", "pdm_hclk";
+		dmas = <&dmac1 9>;
+		dma-names = "rx";
+		pinctrl-0 = <&pdmm0_clk
+			     &pdmm0_clk1
+			     &pdmm0_sdi0
+			     &pdmm0_sdi1
+			     &pdmm0_sdi2
+			     &pdmm0_sdi3>;
+		pinctrl-names = "default";
+		resets = <&cru SRST_M_PDM>;
+		reset-names = "pdm-m";
+		#sound-dai-cells = <0>;
+		status = "disabled";
+	};
+
+	dmac0: dma-controller@fe530000 {
 		compatible = "arm,pl330", "arm,primecell";
 		reg = <0x0 0xfe530000 0x0 0x4000>;
 		interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>,
@@ -658,7 +1153,7 @@
 		#dma-cells = <1>;
 	};
 
-	dmac1: dmac@fe550000 {
+	dmac1: dma-controller@fe550000 {
 		compatible = "arm,pl330", "arm,primecell";
 		reg = <0x0 0xfe550000 0x0 0x4000>;
 		interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>,
@@ -742,6 +1237,66 @@
 		clock-names = "tclk", "pclk";
 	};
 
+	spi0: spi@fe610000 {
+		compatible = "rockchip,rk3568-spi", "rockchip,rk3066-spi";
+		reg = <0x0 0xfe610000 0x0 0x1000>;
+		interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru CLK_SPI0>, <&cru PCLK_SPI0>;
+		clock-names = "spiclk", "apb_pclk";
+		dmas = <&dmac0 20>, <&dmac0 21>;
+		dma-names = "tx", "rx";
+		pinctrl-names = "default";
+		pinctrl-0 = <&spi0m0_cs0 &spi0m0_cs1 &spi0m0_pins>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "disabled";
+	};
+
+	spi1: spi@fe620000 {
+		compatible = "rockchip,rk3568-spi", "rockchip,rk3066-spi";
+		reg = <0x0 0xfe620000 0x0 0x1000>;
+		interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru CLK_SPI1>, <&cru PCLK_SPI1>;
+		clock-names = "spiclk", "apb_pclk";
+		dmas = <&dmac0 22>, <&dmac0 23>;
+		dma-names = "tx", "rx";
+		pinctrl-names = "default";
+		pinctrl-0 = <&spi1m0_cs0 &spi1m0_cs1 &spi1m0_pins>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "disabled";
+	};
+
+	spi2: spi@fe630000 {
+		compatible = "rockchip,rk3568-spi", "rockchip,rk3066-spi";
+		reg = <0x0 0xfe630000 0x0 0x1000>;
+		interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru CLK_SPI2>, <&cru PCLK_SPI2>;
+		clock-names = "spiclk", "apb_pclk";
+		dmas = <&dmac0 24>, <&dmac0 25>;
+		dma-names = "tx", "rx";
+		pinctrl-names = "default";
+		pinctrl-0 = <&spi2m0_cs0 &spi2m0_cs1 &spi2m0_pins>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "disabled";
+	};
+
+	spi3: spi@fe640000 {
+		compatible = "rockchip,rk3568-spi", "rockchip,rk3066-spi";
+		reg = <0x0 0xfe640000 0x0 0x1000>;
+		interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru CLK_SPI3>, <&cru PCLK_SPI3>;
+		clock-names = "spiclk", "apb_pclk";
+		dmas = <&dmac0 26>, <&dmac0 27>;
+		dma-names = "tx", "rx";
+		pinctrl-names = "default";
+		pinctrl-0 = <&spi3m0_cs0 &spi3m0_cs1 &spi3m0_pins>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "disabled";
+	};
+
 	uart1: serial@fe650000 {
 		compatible = "rockchip,rk3568-uart", "snps,dw-apb-uart";
 		reg = <0x0 0xfe650000 0x0 0x100>;
@@ -910,6 +1465,32 @@
 			polling-delay = <1000>; /* milliseconds */
 
 			thermal-sensors = <&tsadc 1>;
+
+			trips {
+				gpu_threshold: gpu-threshold {
+					temperature = <70000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+				gpu_target: gpu-target {
+					temperature = <75000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+				gpu_crit: gpu-crit {
+					temperature = <95000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+
+			cooling-maps {
+				map0 {
+					trip = <&gpu_target>;
+					cooling-device =
+						<&gpu THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
 		};
 	};
 
@@ -951,7 +1532,7 @@
 		clocks = <&cru CLK_PWM1>, <&cru PCLK_PWM1>;
 		clock-names = "pwm", "pclk";
 		pinctrl-0 = <&pwm4_pins>;
-		pinctrl-names = "active";
+		pinctrl-names = "default";
 		#pwm-cells = <3>;
 		status = "disabled";
 	};
@@ -962,7 +1543,7 @@
 		clocks = <&cru CLK_PWM1>, <&cru PCLK_PWM1>;
 		clock-names = "pwm", "pclk";
 		pinctrl-0 = <&pwm5_pins>;
-		pinctrl-names = "active";
+		pinctrl-names = "default";
 		#pwm-cells = <3>;
 		status = "disabled";
 	};
@@ -973,7 +1554,7 @@
 		clocks = <&cru CLK_PWM1>, <&cru PCLK_PWM1>;
 		clock-names = "pwm", "pclk";
 		pinctrl-0 = <&pwm6_pins>;
-		pinctrl-names = "active";
+		pinctrl-names = "default";
 		#pwm-cells = <3>;
 		status = "disabled";
 	};
@@ -984,7 +1565,7 @@
 		clocks = <&cru CLK_PWM1>, <&cru PCLK_PWM1>;
 		clock-names = "pwm", "pclk";
 		pinctrl-0 = <&pwm7_pins>;
-		pinctrl-names = "active";
+		pinctrl-names = "default";
 		#pwm-cells = <3>;
 		status = "disabled";
 	};
@@ -995,7 +1576,7 @@
 		clocks = <&cru CLK_PWM2>, <&cru PCLK_PWM2>;
 		clock-names = "pwm", "pclk";
 		pinctrl-0 = <&pwm8m0_pins>;
-		pinctrl-names = "active";
+		pinctrl-names = "default";
 		#pwm-cells = <3>;
 		status = "disabled";
 	};
@@ -1006,7 +1587,7 @@
 		clocks = <&cru CLK_PWM2>, <&cru PCLK_PWM2>;
 		clock-names = "pwm", "pclk";
 		pinctrl-0 = <&pwm9m0_pins>;
-		pinctrl-names = "active";
+		pinctrl-names = "default";
 		#pwm-cells = <3>;
 		status = "disabled";
 	};
@@ -1017,7 +1598,7 @@
 		clocks = <&cru CLK_PWM2>, <&cru PCLK_PWM2>;
 		clock-names = "pwm", "pclk";
 		pinctrl-0 = <&pwm10m0_pins>;
-		pinctrl-names = "active";
+		pinctrl-names = "default";
 		#pwm-cells = <3>;
 		status = "disabled";
 	};
@@ -1028,7 +1609,7 @@
 		clocks = <&cru CLK_PWM2>, <&cru PCLK_PWM2>;
 		clock-names = "pwm", "pclk";
 		pinctrl-0 = <&pwm11m0_pins>;
-		pinctrl-names = "active";
+		pinctrl-names = "default";
 		#pwm-cells = <3>;
 		status = "disabled";
 	};
@@ -1039,7 +1620,7 @@
 		clocks = <&cru CLK_PWM3>, <&cru PCLK_PWM3>;
 		clock-names = "pwm", "pclk";
 		pinctrl-0 = <&pwm12m0_pins>;
-		pinctrl-names = "active";
+		pinctrl-names = "default";
 		#pwm-cells = <3>;
 		status = "disabled";
 	};
@@ -1050,7 +1631,7 @@
 		clocks = <&cru CLK_PWM3>, <&cru PCLK_PWM3>;
 		clock-names = "pwm", "pclk";
 		pinctrl-0 = <&pwm13m0_pins>;
-		pinctrl-names = "active";
+		pinctrl-names = "default";
 		#pwm-cells = <3>;
 		status = "disabled";
 	};
@@ -1061,7 +1642,7 @@
 		clocks = <&cru CLK_PWM3>, <&cru PCLK_PWM3>;
 		clock-names = "pwm", "pclk";
 		pinctrl-0 = <&pwm14m0_pins>;
-		pinctrl-names = "active";
+		pinctrl-names = "default";
 		#pwm-cells = <3>;
 		status = "disabled";
 	};
@@ -1072,11 +1653,123 @@
 		clocks = <&cru CLK_PWM3>, <&cru PCLK_PWM3>;
 		clock-names = "pwm", "pclk";
 		pinctrl-0 = <&pwm15m0_pins>;
-		pinctrl-names = "active";
+		pinctrl-names = "default";
 		#pwm-cells = <3>;
 		status = "disabled";
 	};
 
+	combphy1: phy@fe830000 {
+		compatible = "rockchip,rk3568-naneng-combphy";
+		reg = <0x0 0xfe830000 0x0 0x100>;
+		clocks = <&pmucru CLK_PCIEPHY1_REF>,
+			 <&cru PCLK_PIPEPHY1>,
+			 <&cru PCLK_PIPE>;
+		clock-names = "ref", "apb", "pipe";
+		assigned-clocks = <&pmucru CLK_PCIEPHY1_REF>;
+		assigned-clock-rates = <100000000>;
+		resets = <&cru SRST_PIPEPHY1>;
+		rockchip,pipe-grf = <&pipegrf>;
+		rockchip,pipe-phy-grf = <&pipe_phy_grf1>;
+		#phy-cells = <1>;
+		status = "disabled";
+	};
+
+	combphy2: phy@fe840000 {
+		compatible = "rockchip,rk3568-naneng-combphy";
+		reg = <0x0 0xfe840000 0x0 0x100>;
+		clocks = <&pmucru CLK_PCIEPHY2_REF>,
+			 <&cru PCLK_PIPEPHY2>,
+			 <&cru PCLK_PIPE>;
+		clock-names = "ref", "apb", "pipe";
+		assigned-clocks = <&pmucru CLK_PCIEPHY2_REF>;
+		assigned-clock-rates = <100000000>;
+		resets = <&cru SRST_PIPEPHY2>;
+		rockchip,pipe-grf = <&pipegrf>;
+		rockchip,pipe-phy-grf = <&pipe_phy_grf2>;
+		#phy-cells = <1>;
+		status = "disabled";
+	};
+
+	csi_dphy: phy@fe870000 {
+		compatible = "rockchip,rk3568-csi-dphy";
+		reg = <0x0 0xfe870000 0x0 0x10000>;
+		clocks = <&cru PCLK_MIPICSIPHY>;
+		clock-names = "pclk";
+		#phy-cells = <0>;
+		resets = <&cru SRST_P_MIPICSIPHY>;
+		reset-names = "apb";
+		rockchip,grf = <&grf>;
+		status = "disabled";
+	};
+
+	dsi_dphy0: mipi-dphy@fe850000 {
+		compatible = "rockchip,rk3568-dsi-dphy";
+		reg = <0x0 0xfe850000 0x0 0x10000>;
+		clock-names = "ref", "pclk";
+		clocks = <&pmucru CLK_MIPIDSIPHY0_REF>, <&cru PCLK_MIPIDSIPHY0>;
+		#phy-cells = <0>;
+		power-domains = <&power RK3568_PD_VO>;
+		reset-names = "apb";
+		resets = <&cru SRST_P_MIPIDSIPHY0>;
+		status = "disabled";
+	};
+
+	dsi_dphy1: mipi-dphy@fe860000 {
+		compatible = "rockchip,rk3568-dsi-dphy";
+		reg = <0x0 0xfe860000 0x0 0x10000>;
+		clock-names = "ref", "pclk";
+		clocks = <&pmucru CLK_MIPIDSIPHY1_REF>, <&cru PCLK_MIPIDSIPHY1>;
+		#phy-cells = <0>;
+		power-domains = <&power RK3568_PD_VO>;
+		reset-names = "apb";
+		resets = <&cru SRST_P_MIPIDSIPHY1>;
+		status = "disabled";
+	};
+
+	usb2phy0: usb2phy@fe8a0000 {
+		compatible = "rockchip,rk3568-usb2phy";
+		reg = <0x0 0xfe8a0000 0x0 0x10000>;
+		clocks = <&pmucru CLK_USBPHY0_REF>;
+		clock-names = "phyclk";
+		clock-output-names = "clk_usbphy0_480m";
+		interrupts = <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>;
+		rockchip,usbgrf = <&usb2phy0_grf>;
+		#clock-cells = <0>;
+		status = "disabled";
+
+		usb2phy0_host: host-port {
+			#phy-cells = <0>;
+			status = "disabled";
+		};
+
+		usb2phy0_otg: otg-port {
+			#phy-cells = <0>;
+			status = "disabled";
+		};
+	};
+
+	usb2phy1: usb2phy@fe8b0000 {
+		compatible = "rockchip,rk3568-usb2phy";
+		reg = <0x0 0xfe8b0000 0x0 0x10000>;
+		clocks = <&pmucru CLK_USBPHY1_REF>;
+		clock-names = "phyclk";
+		clock-output-names = "clk_usbphy1_480m";
+		interrupts = <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>;
+		rockchip,usbgrf = <&usb2phy1_grf>;
+		#clock-cells = <0>;
+		status = "disabled";
+
+		usb2phy1_host: host-port {
+			#phy-cells = <0>;
+			status = "disabled";
+		};
+
+		usb2phy1_otg: otg-port {
+			#phy-cells = <0>;
+			status = "disabled";
+		};
+	};
+
 	pinctrl: pinctrl {
 		compatible = "rockchip,rk3568-pinctrl";
 		rockchip,grf = <&grf>;
diff --git a/arch/arm64/boot/dts/socionext/Makefile b/arch/arm64/boot/dts/socionext/Makefile
index dda3da33614b..33989a9643ac 100644
--- a/arch/arm64/boot/dts/socionext/Makefile
+++ b/arch/arm64/boot/dts/socionext/Makefile
@@ -5,4 +5,6 @@ dtb-$(CONFIG_ARCH_UNIPHIER) += \
 	uniphier-ld20-akebi96.dtb \
 	uniphier-ld20-global.dtb \
 	uniphier-ld20-ref.dtb \
-	uniphier-pxs3-ref.dtb
+	uniphier-pxs3-ref.dtb \
+	uniphier-pxs3-ref-gadget0.dtb \
+	uniphier-pxs3-ref-gadget1.dtb
diff --git a/arch/arm64/boot/dts/socionext/uniphier-ld11-ref.dts b/arch/arm64/boot/dts/socionext/uniphier-ld11-ref.dts
index 617d2b1e9b1e..414aeb99e68f 100644
--- a/arch/arm64/boot/dts/socionext/uniphier-ld11-ref.dts
+++ b/arch/arm64/boot/dts/socionext/uniphier-ld11-ref.dts
@@ -39,11 +39,11 @@
 };
 
 &ethsc {
-	interrupts = <0 8>;
+	interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
 };
 
 &serialsc {
-	interrupts = <0 8>;
+	interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
 };
 
 &serial0 {
@@ -51,7 +51,7 @@
 };
 
 &gpio {
-	xirq0 {
+	xirq0-hog {
 		gpio-hog;
 		gpios = <UNIPHIER_GPIO_IRQ(0) 0>;
 		input;
diff --git a/arch/arm64/boot/dts/socionext/uniphier-ld11.dtsi b/arch/arm64/boot/dts/socionext/uniphier-ld11.dtsi
index 15dcfc259854..1c76b4375b2e 100644
--- a/arch/arm64/boot/dts/socionext/uniphier-ld11.dtsi
+++ b/arch/arm64/boot/dts/socionext/uniphier-ld11.dtsi
@@ -7,6 +7,7 @@
 
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/gpio/uniphier-gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
 
 / {
 	compatible = "socionext,uniphier-ld11";
@@ -35,6 +36,7 @@
 			reg = <0 0x000>;
 			clocks = <&sys_clk 33>;
 			enable-method = "psci";
+			next-level-cache = <&l2>;
 			operating-points-v2 = <&cluster0_opp>;
 		};
 
@@ -44,8 +46,13 @@
 			reg = <0 0x001>;
 			clocks = <&sys_clk 33>;
 			enable-method = "psci";
+			next-level-cache = <&l2>;
 			operating-points-v2 = <&cluster0_opp>;
 		};
+
+		l2: l2-cache {
+			compatible = "cache";
+		};
 	};
 
 	cluster0_opp: opp-table {
@@ -102,10 +109,10 @@
 
 	timer {
 		compatible = "arm,armv8-timer";
-		interrupts = <1 13 4>,
-			     <1 14 4>,
-			     <1 11 4>,
-			     <1 10 4>;
+		interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_PPI 14 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_PPI 11 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_PPI 10 IRQ_TYPE_LEVEL_HIGH>;
 	};
 
 	reserved-memory {
@@ -131,7 +138,7 @@
 			reg = <0x54006000 0x100>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 39 4>;
+			interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_spi0>;
 			clocks = <&peri_clk 11>;
@@ -144,7 +151,7 @@
 			reg = <0x54006100 0x100>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 216 4>;
+			interrupts = <GIC_SPI 216 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_spi1>;
 			clocks = <&peri_clk 12>;
@@ -155,7 +162,7 @@
 			compatible = "socionext,uniphier-uart";
 			status = "disabled";
 			reg = <0x54006800 0x40>;
-			interrupts = <0 33 4>;
+			interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_uart0>;
 			clocks = <&peri_clk 0>;
@@ -166,7 +173,7 @@
 			compatible = "socionext,uniphier-uart";
 			status = "disabled";
 			reg = <0x54006900 0x40>;
-			interrupts = <0 35 4>;
+			interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_uart1>;
 			clocks = <&peri_clk 1>;
@@ -177,7 +184,7 @@
 			compatible = "socionext,uniphier-uart";
 			status = "disabled";
 			reg = <0x54006a00 0x40>;
-			interrupts = <0 37 4>;
+			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_uart2>;
 			clocks = <&peri_clk 2>;
@@ -188,7 +195,7 @@
 			compatible = "socionext,uniphier-uart";
 			status = "disabled";
 			reg = <0x54006b00 0x40>;
-			interrupts = <0 177 4>;
+			interrupts = <GIC_SPI 177 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_uart3>;
 			clocks = <&peri_clk 3>;
@@ -223,7 +230,7 @@
 		audio@56000000 {
 			compatible = "socionext,uniphier-ld11-aio";
 			reg = <0x56000000 0x80000>;
-			interrupts = <0 144 4>;
+			interrupts = <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_aout1>,
 				    <&pinctrl_aoutiec1>;
@@ -323,7 +330,7 @@
 			reg = <0x58780000 0x80>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 41 4>;
+			interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_i2c0>;
 			clocks = <&peri_clk 4>;
@@ -337,7 +344,7 @@
 			reg = <0x58781000 0x80>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 42 4>;
+			interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_i2c1>;
 			clocks = <&peri_clk 5>;
@@ -350,7 +357,7 @@
 			reg = <0x58782000 0x80>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 43 4>;
+			interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&peri_clk 6>;
 			resets = <&peri_rst 6>;
 			clock-frequency = <400000>;
@@ -362,7 +369,7 @@
 			reg = <0x58783000 0x80>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 44 4>;
+			interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_i2c3>;
 			clocks = <&peri_clk 7>;
@@ -376,7 +383,7 @@
 			reg = <0x58784000 0x80>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 45 4>;
+			interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_i2c4>;
 			clocks = <&peri_clk 8>;
@@ -389,7 +396,7 @@
 			reg = <0x58785000 0x80>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 25 4>;
+			interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&peri_clk 9>;
 			resets = <&peri_rst 9>;
 			clock-frequency = <400000>;
@@ -440,7 +447,7 @@
 		emmc: mmc@5a000000 {
 			compatible = "socionext,uniphier-sd4hc", "cdns,sd4hc";
 			reg = <0x5a000000 0x400>;
-			interrupts = <0 78 4>;
+			interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_emmc>;
 			clocks = <&sys_clk 4>;
@@ -460,7 +467,7 @@
 			compatible = "socionext,uniphier-ehci", "generic-ehci";
 			status = "disabled";
 			reg = <0x5a800100 0x100>;
-			interrupts = <0 243 4>;
+			interrupts = <GIC_SPI 243 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_usb0>;
 			clocks = <&sys_clk 8>, <&mio_clk 7>, <&mio_clk 8>,
@@ -476,7 +483,7 @@
 			compatible = "socionext,uniphier-ehci", "generic-ehci";
 			status = "disabled";
 			reg = <0x5a810100 0x100>;
-			interrupts = <0 244 4>;
+			interrupts = <GIC_SPI 244 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_usb1>;
 			clocks = <&sys_clk 8>, <&mio_clk 7>, <&mio_clk 9>,
@@ -492,7 +499,7 @@
 			compatible = "socionext,uniphier-ehci", "generic-ehci";
 			status = "disabled";
 			reg = <0x5a820100 0x100>;
-			interrupts = <0 245 4>;
+			interrupts = <GIC_SPI 245 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_usb2>;
 			clocks = <&sys_clk 8>, <&mio_clk 7>, <&mio_clk 10>,
@@ -530,7 +537,7 @@
 				compatible = "socionext,uniphier-ld11-pinctrl";
 			};
 
-			usb-phy {
+			usb-controller {
 				compatible = "socionext,uniphier-ld11-usb2-phy";
 				#address-cells = <1>;
 				#size-cells = <0>;
@@ -573,7 +580,7 @@
 		xdmac: dma-controller@5fc10000 {
 			compatible = "socionext,uniphier-xdmac";
 			reg = <0x5fc10000 0x5300>;
-			interrupts = <0 188 4>;
+			interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>;
 			dma-channels = <16>;
 			#dma-cells = <2>;
 		};
@@ -591,7 +598,7 @@
 			      <0x5fe40000 0x80000>;	/* GICR */
 			interrupt-controller;
 			#interrupt-cells = <3>;
-			interrupts = <1 9 4>;
+			interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
 		};
 
 		sysctrl@61840000 {
@@ -618,7 +625,7 @@
 			compatible = "socionext,uniphier-ld11-ave4";
 			status = "disabled";
 			reg = <0x65000000 0x8500>;
-			interrupts = <0 66 4>;
+			interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>;
 			clock-names = "ether";
 			clocks = <&sys_clk 6>;
 			reset-names = "ether";
@@ -640,7 +647,7 @@
 			reg = <0x68000000 0x20>, <0x68100000 0x1000>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 65 4>;
+			interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_nand>;
 			clock-names = "nand", "nand_x", "ecc";
diff --git a/arch/arm64/boot/dts/socionext/uniphier-ld20-akebi96.dts b/arch/arm64/boot/dts/socionext/uniphier-ld20-akebi96.dts
index aa159a11292c..fba454adae7d 100644
--- a/arch/arm64/boot/dts/socionext/uniphier-ld20-akebi96.dts
+++ b/arch/arm64/boot/dts/socionext/uniphier-ld20-akebi96.dts
@@ -110,7 +110,7 @@
 		spi-max-frequency = <12500000>;
 		interrupt-parent = <&gpio>;
 		interrupt-names = "udc";
-		interrupts = <0 2>;
+		interrupts = <0 IRQ_TYPE_EDGE_FALLING>;
 	};
 };
 
@@ -168,12 +168,12 @@
 
 &gpio {
 	/* IRQs for Max3421 */
-	xirq0 {
+	xirq0-hog {
 		gpio-hog;
 		gpios = <UNIPHIER_GPIO_IRQ(0) 1>;
 		input;
 	};
-	xirq10 {
+	xirq10-hog {
 		gpio-hog;
 		gpios = <UNIPHIER_GPIO_IRQ(10) 1>;
 		input;
diff --git a/arch/arm64/boot/dts/socionext/uniphier-ld20-ref.dts b/arch/arm64/boot/dts/socionext/uniphier-ld20-ref.dts
index 39ee279a1eb9..a5f2083f8b75 100644
--- a/arch/arm64/boot/dts/socionext/uniphier-ld20-ref.dts
+++ b/arch/arm64/boot/dts/socionext/uniphier-ld20-ref.dts
@@ -39,11 +39,11 @@
 };
 
 &ethsc {
-	interrupts = <0 8>;
+	interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
 };
 
 &serialsc {
-	interrupts = <0 8>;
+	interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
 };
 
 &serial0 {
@@ -51,7 +51,7 @@
 };
 
 &gpio {
-	xirq0 {
+	xirq0-hog {
 		gpio-hog;
 		gpios = <UNIPHIER_GPIO_IRQ(0) 0>;
 		input;
diff --git a/arch/arm64/boot/dts/socionext/uniphier-ld20.dtsi b/arch/arm64/boot/dts/socionext/uniphier-ld20.dtsi
index 8f2c1c1e2c64..9308458f9611 100644
--- a/arch/arm64/boot/dts/socionext/uniphier-ld20.dtsi
+++ b/arch/arm64/boot/dts/socionext/uniphier-ld20.dtsi
@@ -7,6 +7,7 @@
 
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/gpio/uniphier-gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/thermal/thermal.h>
 
 / {
@@ -45,6 +46,7 @@
 			reg = <0 0x000>;
 			clocks = <&sys_clk 32>;
 			enable-method = "psci";
+			next-level-cache = <&a72_l2>;
 			operating-points-v2 = <&cluster0_opp>;
 			#cooling-cells = <2>;
 		};
@@ -55,6 +57,7 @@
 			reg = <0 0x001>;
 			clocks = <&sys_clk 32>;
 			enable-method = "psci";
+			next-level-cache = <&a72_l2>;
 			operating-points-v2 = <&cluster0_opp>;
 			#cooling-cells = <2>;
 		};
@@ -65,6 +68,7 @@
 			reg = <0 0x100>;
 			clocks = <&sys_clk 33>;
 			enable-method = "psci";
+			next-level-cache = <&a53_l2>;
 			operating-points-v2 = <&cluster1_opp>;
 			#cooling-cells = <2>;
 		};
@@ -75,12 +79,21 @@
 			reg = <0 0x101>;
 			clocks = <&sys_clk 33>;
 			enable-method = "psci";
+			next-level-cache = <&a53_l2>;
 			operating-points-v2 = <&cluster1_opp>;
 			#cooling-cells = <2>;
 		};
+
+		a72_l2: l2-cache0 {
+			compatible = "cache";
+		};
+
+		a53_l2: l2-cache1 {
+			compatible = "cache";
+		};
 	};
 
-	cluster0_opp: opp-table0 {
+	cluster0_opp: opp-table-0 {
 		compatible = "operating-points-v2";
 		opp-shared;
 
@@ -118,7 +131,7 @@
 		};
 	};
 
-	cluster1_opp: opp-table1 {
+	cluster1_opp: opp-table-1 {
 		compatible = "operating-points-v2";
 		opp-shared;
 
@@ -176,10 +189,10 @@
 
 	timer {
 		compatible = "arm,armv8-timer";
-		interrupts = <1 13 4>,
-			     <1 14 4>,
-			     <1 11 4>,
-			     <1 10 4>;
+		interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_PPI 14 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_PPI 11 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_PPI 10 IRQ_TYPE_LEVEL_HIGH>;
 	};
 
 	thermal-zones {
@@ -236,7 +249,7 @@
 			reg = <0x54006000 0x100>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 39 4>;
+			interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_spi0>;
 			clocks = <&peri_clk 11>;
@@ -249,7 +262,7 @@
 			reg = <0x54006100 0x100>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 216 4>;
+			interrupts = <GIC_SPI 216 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_spi1>;
 			clocks = <&peri_clk 12>;
@@ -262,7 +275,7 @@
 			reg = <0x54006200 0x100>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 229 4>;
+			interrupts = <GIC_SPI 229 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_spi2>;
 			clocks = <&peri_clk 13>;
@@ -275,7 +288,7 @@
 			reg = <0x54006300 0x100>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 230 4>;
+			interrupts = <GIC_SPI 230 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_spi3>;
 			clocks = <&peri_clk 14>;
@@ -286,7 +299,7 @@
 			compatible = "socionext,uniphier-uart";
 			status = "disabled";
 			reg = <0x54006800 0x40>;
-			interrupts = <0 33 4>;
+			interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_uart0>;
 			clocks = <&peri_clk 0>;
@@ -297,7 +310,7 @@
 			compatible = "socionext,uniphier-uart";
 			status = "disabled";
 			reg = <0x54006900 0x40>;
-			interrupts = <0 35 4>;
+			interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_uart1>;
 			clocks = <&peri_clk 1>;
@@ -308,7 +321,7 @@
 			compatible = "socionext,uniphier-uart";
 			status = "disabled";
 			reg = <0x54006a00 0x40>;
-			interrupts = <0 37 4>;
+			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_uart2>;
 			clocks = <&peri_clk 2>;
@@ -319,7 +332,7 @@
 			compatible = "socionext,uniphier-uart";
 			status = "disabled";
 			reg = <0x54006b00 0x40>;
-			interrupts = <0 177 4>;
+			interrupts = <GIC_SPI 177 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_uart3>;
 			clocks = <&peri_clk 3>;
@@ -348,7 +361,7 @@
 		audio@56000000 {
 			compatible = "socionext,uniphier-ld20-aio";
 			reg = <0x56000000 0x80000>;
-			interrupts = <0 144 4>;
+			interrupts = <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_aout1>,
 				    <&pinctrl_aoutiec1>;
@@ -448,7 +461,7 @@
 			reg = <0x58780000 0x80>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 41 4>;
+			interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_i2c0>;
 			clocks = <&peri_clk 4>;
@@ -462,7 +475,7 @@
 			reg = <0x58781000 0x80>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 42 4>;
+			interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_i2c1>;
 			clocks = <&peri_clk 5>;
@@ -475,7 +488,7 @@
 			reg = <0x58782000 0x80>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 43 4>;
+			interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&peri_clk 6>;
 			resets = <&peri_rst 6>;
 			clock-frequency = <400000>;
@@ -487,7 +500,7 @@
 			reg = <0x58783000 0x80>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 44 4>;
+			interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_i2c3>;
 			clocks = <&peri_clk 7>;
@@ -501,7 +514,7 @@
 			reg = <0x58784000 0x80>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 45 4>;
+			interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_i2c4>;
 			clocks = <&peri_clk 8>;
@@ -514,7 +527,7 @@
 			reg = <0x58785000 0x80>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 25 4>;
+			interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&peri_clk 9>;
 			resets = <&peri_rst 9>;
 			clock-frequency = <400000>;
@@ -570,7 +583,7 @@
 		emmc: mmc@5a000000 {
 			compatible = "socionext,uniphier-sd4hc", "cdns,sd4hc";
 			reg = <0x5a000000 0x400>;
-			interrupts = <0 78 4>;
+			interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_emmc>;
 			clocks = <&sys_clk 4>;
@@ -590,7 +603,7 @@
 			compatible = "socionext,uniphier-sd-v3.1.1";
 			status = "disabled";
 			reg = <0x5a400000 0x800>;
-			interrupts = <0 76 4>;
+			interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_sd>;
 			clocks = <&sd_clk 0>;
@@ -675,7 +688,7 @@
 		xdmac: dma-controller@5fc10000 {
 			compatible = "socionext,uniphier-xdmac";
 			reg = <0x5fc10000 0x5300>;
-			interrupts = <0 188 4>;
+			interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>;
 			dma-channels = <16>;
 			#dma-cells = <2>;
 		};
@@ -693,7 +706,7 @@
 			      <0x5fe80000 0x80000>;	/* GICR */
 			interrupt-controller;
 			#interrupt-cells = <3>;
-			interrupts = <1 9 4>;
+			interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
 		};
 
 		sysctrl@61840000 {
@@ -715,9 +728,9 @@
 				compatible = "socionext,uniphier-wdt";
 			};
 
-			pvtctl: pvtctl {
+			pvtctl: thermal-sensor {
 				compatible = "socionext,uniphier-ld20-thermal";
-				interrupts = <0 3 4>;
+				interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
 				#thermal-sensor-cells = <0>;
 				socionext,tmod-calibration = <0x0f22 0x68ee>;
 			};
@@ -727,7 +740,7 @@
 			compatible = "socionext,uniphier-ld20-ave4";
 			status = "disabled";
 			reg = <0x65000000 0x8500>;
-			interrupts = <0 66 4>;
+			interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_ether_rgmii>;
 			clock-names = "ether";
@@ -749,7 +762,7 @@
 			status = "disabled";
 			reg = <0x65a00000 0xcd00>;
 			interrupt-names = "host";
-			interrupts = <0 134 4>;
+			interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_usb0>, <&pinctrl_usb1>,
 				    <&pinctrl_usb2>, <&pinctrl_usb3>;
@@ -762,7 +775,7 @@
 			dr_mode = "host";
 		};
 
-		usb-glue@65b00000 {
+		usb-controller@65b00000 {
 			compatible = "socionext,uniphier-ld20-dwc3-glue",
 				     "simple-mfd";
 			#address-cells = <1>;
@@ -895,7 +908,7 @@
 		};
 
 		pcie: pcie@66000000 {
-			compatible = "socionext,uniphier-pcie", "snps,dw-pcie";
+			compatible = "socionext,uniphier-pcie";
 			status = "disabled";
 			reg-names = "dbi", "link", "config";
 			reg = <0x66000000 0x1000>, <0x66010000 0x10000>,
@@ -915,7 +928,8 @@
 				<0x82000000 0 0x20000000 0x20000000 0 0x0ffe0000>;
 			#interrupt-cells = <1>;
 			interrupt-names = "dma", "msi";
-			interrupts = <0 224 4>, <0 225 4>;
+			interrupts = <GIC_SPI 224 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 225 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-map-mask = <0 0 0 7>;
 			interrupt-map = <0 0 0 1 &pcie_intc 0>,	/* INTA */
 					<0 0 0 2 &pcie_intc 1>,	/* INTB */
@@ -928,7 +942,7 @@
 				interrupt-controller;
 				#interrupt-cells = <1>;
 				interrupt-parent = <&gic>;
-				interrupts = <0 226 4>;
+				interrupts = <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>;
 			};
 		};
 
@@ -950,7 +964,7 @@
 			reg = <0x68000000 0x20>, <0x68100000 0x1000>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 65 4>;
+			interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_nand>;
 			clock-names = "nand", "nand_x", "ecc";
diff --git a/arch/arm64/boot/dts/socionext/uniphier-pxs3-ref-gadget0.dts b/arch/arm64/boot/dts/socionext/uniphier-pxs3-ref-gadget0.dts
new file mode 100644
index 000000000000..7069f51bc120
--- /dev/null
+++ b/arch/arm64/boot/dts/socionext/uniphier-pxs3-ref-gadget0.dts
@@ -0,0 +1,41 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+//
+// Device Tree Source for UniPhier PXs3 Reference Board (for USB-Device #0)
+//
+// Copyright (C) 2021 Socionext Inc.
+//   Author: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
+
+/dts-v1/;
+#include "uniphier-pxs3-ref.dts"
+
+/ {
+	model = "UniPhier PXs3 Reference Board (USB-Device #0)";
+};
+
+/* I2C3 pinctrl is shared with USB*VBUSIN */
+&i2c3 {
+	status = "disabled";
+};
+
+&usb0 {
+	status = "okay";
+	dr_mode = "peripheral";
+	pinctrl-0 = <&pinctrl_usb0_device>;
+	snps,dis_enblslpm_quirk;
+	snps,dis_u2_susphy_quirk;
+	snps,dis_u3_susphy_quirk;
+	snps,usb2_gadget_lpm_disable;
+	phy-names = "usb2-phy", "usb3-phy";
+	phys = <&usb0_hsphy0>, <&usb0_ssphy0>;
+};
+
+&usb0_hsphy0 {
+	/delete-property/ vbus-supply;
+};
+
+&usb0_ssphy0 {
+	/delete-property/ vbus-supply;
+};
+
+/delete-node/ &usb0_hsphy1;
+/delete-node/ &usb0_ssphy1;
diff --git a/arch/arm64/boot/dts/socionext/uniphier-pxs3-ref-gadget1.dts b/arch/arm64/boot/dts/socionext/uniphier-pxs3-ref-gadget1.dts
new file mode 100644
index 000000000000..a3cfa8113ffb
--- /dev/null
+++ b/arch/arm64/boot/dts/socionext/uniphier-pxs3-ref-gadget1.dts
@@ -0,0 +1,40 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+//
+// Device Tree Source for UniPhier PXs3 Reference Board (for USB-Device #1)
+//
+// Copyright (C) 2021 Socionext Inc.
+//   Author: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
+
+/dts-v1/;
+#include "uniphier-pxs3-ref.dts"
+
+/ {
+	model = "UniPhier PXs3 Reference Board (USB-Device #1)";
+};
+
+/* I2C3 pinctrl is shared with USB*VBUSIN */
+&i2c3 {
+	status = "disabled";
+};
+
+&usb1 {
+	status = "okay";
+	dr_mode = "peripheral";
+	pinctrl-0 = <&pinctrl_usb1_device>;
+	snps,dis_enblslpm_quirk;
+	snps,dis_u2_susphy_quirk;
+	snps,dis_u3_susphy_quirk;
+	snps,usb2_gadget_lpm_disable;
+	phy-names = "usb2-phy", "usb3-phy";
+	phys = <&usb1_hsphy0>, <&usb1_ssphy0>;
+};
+
+&usb1_hsphy0 {
+	/delete-property/ vbus-supply;
+};
+
+&usb1_ssphy0 {
+	/delete-property/ vbus-supply;
+};
+
+/delete-node/ &usb1_hsphy1;
diff --git a/arch/arm64/boot/dts/socionext/uniphier-pxs3-ref.dts b/arch/arm64/boot/dts/socionext/uniphier-pxs3-ref.dts
index 086040306fb3..1ced6190ab2b 100644
--- a/arch/arm64/boot/dts/socionext/uniphier-pxs3-ref.dts
+++ b/arch/arm64/boot/dts/socionext/uniphier-pxs3-ref.dts
@@ -40,11 +40,11 @@
 };
 
 &ethsc {
-	interrupts = <4 8>;
+	interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
 };
 
 &serialsc {
-	interrupts = <4 8>;
+	interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
 };
 
 &spi0 {
@@ -68,7 +68,7 @@
 };
 
 &gpio {
-	xirq4 {
+	xirq4-hog {
 		gpio-hog;
 		gpios = <UNIPHIER_GPIO_IRQ(4) 0>;
 		input;
@@ -137,6 +137,14 @@
 	};
 };
 
+&ahci0 {
+	status = "okay";
+};
+
+&ahci1 {
+	status = "okay";
+};
+
 &pinctrl_ether_rgmii {
 	tx {
 		pins = "RGMII0_TXCLK", "RGMII0_TXD0", "RGMII0_TXD1",
diff --git a/arch/arm64/boot/dts/socionext/uniphier-pxs3.dtsi b/arch/arm64/boot/dts/socionext/uniphier-pxs3.dtsi
index be97da132258..b0c29510a7da 100644
--- a/arch/arm64/boot/dts/socionext/uniphier-pxs3.dtsi
+++ b/arch/arm64/boot/dts/socionext/uniphier-pxs3.dtsi
@@ -7,6 +7,7 @@
 
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/gpio/uniphier-gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/thermal/thermal.h>
 
 / {
@@ -42,6 +43,7 @@
 			reg = <0 0x000>;
 			clocks = <&sys_clk 33>;
 			enable-method = "psci";
+			next-level-cache = <&l2>;
 			operating-points-v2 = <&cluster0_opp>;
 			#cooling-cells = <2>;
 		};
@@ -52,6 +54,7 @@
 			reg = <0 0x001>;
 			clocks = <&sys_clk 33>;
 			enable-method = "psci";
+			next-level-cache = <&l2>;
 			operating-points-v2 = <&cluster0_opp>;
 			#cooling-cells = <2>;
 		};
@@ -62,6 +65,7 @@
 			reg = <0 0x002>;
 			clocks = <&sys_clk 33>;
 			enable-method = "psci";
+			next-level-cache = <&l2>;
 			operating-points-v2 = <&cluster0_opp>;
 			#cooling-cells = <2>;
 		};
@@ -72,9 +76,14 @@
 			reg = <0 0x003>;
 			clocks = <&sys_clk 33>;
 			enable-method = "psci";
+			next-level-cache = <&l2>;
 			operating-points-v2 = <&cluster0_opp>;
 			#cooling-cells = <2>;
 		};
+
+		l2: l2-cache {
+			compatible = "cache";
+		};
 	};
 
 	cluster0_opp: opp-table {
@@ -135,10 +144,10 @@
 
 	timer {
 		compatible = "arm,armv8-timer";
-		interrupts = <1 13 4>,
-			     <1 14 4>,
-			     <1 11 4>,
-			     <1 10 4>;
+		interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_PPI 14 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_PPI 11 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_PPI 10 IRQ_TYPE_LEVEL_HIGH>;
 	};
 
 	thermal-zones {
@@ -195,7 +204,7 @@
 			reg = <0x54006000 0x100>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 39 4>;
+			interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_spi0>;
 			clocks = <&peri_clk 11>;
@@ -208,7 +217,7 @@
 			reg = <0x54006100 0x100>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 216 4>;
+			interrupts = <GIC_SPI 216 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_spi1>;
 			clocks = <&peri_clk 12>;
@@ -219,7 +228,7 @@
 			compatible = "socionext,uniphier-uart";
 			status = "disabled";
 			reg = <0x54006800 0x40>;
-			interrupts = <0 33 4>;
+			interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_uart0>;
 			clocks = <&peri_clk 0>;
@@ -230,7 +239,7 @@
 			compatible = "socionext,uniphier-uart";
 			status = "disabled";
 			reg = <0x54006900 0x40>;
-			interrupts = <0 35 4>;
+			interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_uart1>;
 			clocks = <&peri_clk 1>;
@@ -241,7 +250,7 @@
 			compatible = "socionext,uniphier-uart";
 			status = "disabled";
 			reg = <0x54006a00 0x40>;
-			interrupts = <0 37 4>;
+			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_uart2>;
 			clocks = <&peri_clk 2>;
@@ -252,7 +261,7 @@
 			compatible = "socionext,uniphier-uart";
 			status = "disabled";
 			reg = <0x54006b00 0x40>;
-			interrupts = <0 177 4>;
+			interrupts = <GIC_SPI 177 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_uart3>;
 			clocks = <&peri_clk 3>;
@@ -284,7 +293,7 @@
 			reg = <0x58780000 0x80>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 41 4>;
+			interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_i2c0>;
 			clocks = <&peri_clk 4>;
@@ -298,7 +307,7 @@
 			reg = <0x58781000 0x80>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 42 4>;
+			interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_i2c1>;
 			clocks = <&peri_clk 5>;
@@ -312,7 +321,7 @@
 			reg = <0x58782000 0x80>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 43 4>;
+			interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_i2c2>;
 			clocks = <&peri_clk 6>;
@@ -326,7 +335,7 @@
 			reg = <0x58783000 0x80>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 44 4>;
+			interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_i2c3>;
 			clocks = <&peri_clk 7>;
@@ -340,7 +349,7 @@
 			reg = <0x58786000 0x80>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 26 4>;
+			interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&peri_clk 10>;
 			resets = <&peri_rst 10>;
 			clock-frequency = <400000>;
@@ -396,7 +405,7 @@
 		emmc: mmc@5a000000 {
 			compatible = "socionext,uniphier-sd4hc", "cdns,sd4hc";
 			reg = <0x5a000000 0x400>;
-			interrupts = <0 78 4>;
+			interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_emmc>;
 			clocks = <&sys_clk 4>;
@@ -416,7 +425,7 @@
 			compatible = "socionext,uniphier-sd-v3.1.1";
 			status = "disabled";
 			reg = <0x5a400000 0x800>;
-			interrupts = <0 76 4>;
+			interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default", "uhs";
 			pinctrl-0 = <&pinctrl_sd>;
 			pinctrl-1 = <&pinctrl_sd_uhs>;
@@ -505,7 +514,7 @@
 		xdmac: dma-controller@5fc10000 {
 			compatible = "socionext,uniphier-xdmac";
 			reg = <0x5fc10000 0x5300>;
-			interrupts = <0 188 4>;
+			interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>;
 			dma-channels = <16>;
 			#dma-cells = <2>;
 		};
@@ -523,7 +532,7 @@
 			      <0x5fe80000 0x80000>;	/* GICR */
 			interrupt-controller;
 			#interrupt-cells = <3>;
-			interrupts = <1 9 4>;
+			interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
 		};
 
 		sysctrl@61840000 {
@@ -545,9 +554,9 @@
 				compatible = "socionext,uniphier-wdt";
 			};
 
-			pvtctl: pvtctl {
+			pvtctl: thermal-sensor {
 				compatible = "socionext,uniphier-pxs3-thermal";
-				interrupts = <0 3 4>;
+				interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
 				#thermal-sensor-cells = <0>;
 				socionext,tmod-calibration = <0x0f22 0x68ee>;
 			};
@@ -557,7 +566,7 @@
 			compatible = "socionext,uniphier-pxs3-ave4";
 			status = "disabled";
 			reg = <0x65000000 0x8500>;
-			interrupts = <0 66 4>;
+			interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_ether_rgmii>;
 			clock-names = "ether";
@@ -578,7 +587,7 @@
 			compatible = "socionext,uniphier-pxs3-ave4";
 			status = "disabled";
 			reg = <0x65200000 0x8500>;
-			interrupts = <0 67 4>;
+			interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_ether1_rgmii>;
 			clock-names = "ether";
@@ -595,12 +604,92 @@
 			};
 		};
 
+		ahci0: sata@65600000 {
+			compatible = "socionext,uniphier-pxs3-ahci",
+				     "generic-ahci";
+			status = "disabled";
+			reg = <0x65600000 0x10000>;
+			interrupts = <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&sys_clk 28>;
+			resets = <&sys_rst 28>, <&ahci0_rst 0>;
+			ports-implemented = <1>;
+			phys = <&ahci0_phy>;
+		};
+
+		sata-controller@65700000 {
+			compatible = "socionext,uniphier-pxs3-ahci-glue",
+				     "simple-mfd";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x65700000 0x100>;
+
+			ahci0_rst: reset-controller@0 {
+				compatible = "socionext,uniphier-pxs3-ahci-reset";
+				reg = <0x0 0x4>;
+				clock-names = "link";
+				clocks = <&sys_clk 28>;
+				reset-names = "link";
+				resets = <&sys_rst 28>;
+				#reset-cells = <1>;
+			};
+
+			ahci0_phy: sata-phy@10 {
+				compatible = "socionext,uniphier-pxs3-ahci-phy";
+				reg = <0x10 0x10>;
+				clock-names = "link", "phy";
+				clocks = <&sys_clk 28>, <&sys_clk 30>;
+				reset-names = "link", "phy";
+				resets = <&sys_rst 28>, <&sys_rst 30>;
+				#phy-cells = <0>;
+			};
+		};
+
+		ahci1: sata@65800000 {
+			compatible = "socionext,uniphier-pxs3-ahci",
+				     "generic-ahci";
+			status = "disabled";
+			reg = <0x65800000 0x10000>;
+			interrupts = <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&sys_clk 29>;
+			resets = <&sys_rst 29>, <&ahci1_rst 0>;
+			ports-implemented = <1>;
+			phys = <&ahci1_phy>;
+		};
+
+		sata-controller@65900000 {
+			compatible = "socionext,uniphier-pxs3-ahci-glue",
+				     "simple-mfd";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 0x65900000 0x100>;
+
+			ahci1_rst: reset-controller@0 {
+				compatible = "socionext,uniphier-pxs3-ahci-reset";
+				reg = <0x0 0x4>;
+				clock-names = "link";
+				clocks = <&sys_clk 29>;
+				reset-names = "link";
+				resets = <&sys_rst 29>;
+				#reset-cells = <1>;
+			};
+
+			ahci1_phy: sata-phy@10 {
+				compatible = "socionext,uniphier-pxs3-ahci-phy";
+				reg = <0x10 0x10>;
+				clock-names = "link", "phy";
+				clocks = <&sys_clk 29>, <&sys_clk 30>;
+				reset-names = "link", "phy";
+				resets = <&sys_rst 29>, <&sys_rst 30>;
+				#phy-cells = <0>;
+			};
+		};
+
 		usb0: usb@65a00000 {
 			compatible = "socionext,uniphier-dwc3", "snps,dwc3";
 			status = "disabled";
 			reg = <0x65a00000 0xcd00>;
-			interrupt-names = "host", "peripheral";
-			interrupts = <0 134 4>, <0 135 4>;
+			interrupt-names = "dwc_usb3";
+			interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_usb0>, <&pinctrl_usb2>;
 			clock-names = "ref", "bus_early", "suspend";
@@ -611,7 +700,7 @@
 			dr_mode = "host";
 		};
 
-		usb-glue@65b00000 {
+		usb-controller@65b00000 {
 			compatible = "socionext,uniphier-pxs3-dwc3-glue",
 				     "simple-mfd";
 			#address-cells = <1>;
@@ -701,8 +790,8 @@
 			compatible = "socionext,uniphier-dwc3", "snps,dwc3";
 			status = "disabled";
 			reg = <0x65c00000 0xcd00>;
-			interrupt-names = "host", "peripheral";
-			interrupts = <0 137 4>, <0 138 4>;
+			interrupt-names = "dwc_usb3";
+			interrupts = <GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_usb1>, <&pinctrl_usb3>;
 			clock-names = "ref", "bus_early", "suspend";
@@ -713,7 +802,7 @@
 			dr_mode = "host";
 		};
 
-		usb-glue@65d00000 {
+		usb-controller@65d00000 {
 			compatible = "socionext,uniphier-pxs3-dwc3-glue",
 				     "simple-mfd";
 			#address-cells = <1>;
@@ -792,7 +881,7 @@
 		};
 
 		pcie: pcie@66000000 {
-			compatible = "socionext,uniphier-pcie", "snps,dw-pcie";
+			compatible = "socionext,uniphier-pcie";
 			status = "disabled";
 			reg-names = "dbi", "link", "config";
 			reg = <0x66000000 0x1000>, <0x66010000 0x10000>,
@@ -812,7 +901,8 @@
 				<0x82000000 0 0x20000000 0x20000000 0 0x0ffe0000>;
 			#interrupt-cells = <1>;
 			interrupt-names = "dma", "msi";
-			interrupts = <0 224 4>, <0 225 4>;
+			interrupts = <GIC_SPI 224 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 225 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-map-mask = <0 0 0 7>;
 			interrupt-map = <0 0 0 1 &pcie_intc 0>,	/* INTA */
 					<0 0 0 2 &pcie_intc 1>,	/* INTB */
@@ -825,7 +915,7 @@
 				interrupt-controller;
 				#interrupt-cells = <1>;
 				interrupt-parent = <&gic>;
-				interrupts = <0 226 4>;
+				interrupts = <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>;
 			};
 		};
 
@@ -847,7 +937,7 @@
 			reg = <0x68000000 0x20>, <0x68100000 0x1000>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			interrupts = <0 65 4>;
+			interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_nand>;
 			clock-names = "nand", "nand_x", "ecc";
diff --git a/arch/arm64/boot/dts/sprd/sc9836.dtsi b/arch/arm64/boot/dts/sprd/sc9836.dtsi
index 231436be0e3f..8bb8a70966d2 100644
--- a/arch/arm64/boot/dts/sprd/sc9836.dtsi
+++ b/arch/arm64/boot/dts/sprd/sc9836.dtsi
@@ -207,11 +207,11 @@
 	};
 
 	psci {
-		compatible	= "arm,psci";
-		method		= "smc";
-		cpu_on		= <0xc4000003>;
-		cpu_off		= <0x84000002>;
-		cpu_suspend	= <0xc4000001>;
+		compatible = "arm,psci";
+		method = "smc";
+		cpu_on = <0xc4000003>;
+		cpu_off = <0x84000002>;
+		cpu_suspend = <0xc4000001>;
 	};
 
 	timer {
diff --git a/arch/arm64/boot/dts/sprd/sc9863a.dtsi b/arch/arm64/boot/dts/sprd/sc9863a.dtsi
index 8cf4a6575980..22d81ace740a 100644
--- a/arch/arm64/boot/dts/sprd/sc9863a.dtsi
+++ b/arch/arm64/boot/dts/sprd/sc9863a.dtsi
@@ -552,7 +552,7 @@
 			ranges;
 
 			sdio0: sdio@20300000 {
-				compatible  = "sprd,sdhci-r11";
+				compatible = "sprd,sdhci-r11";
 				reg = <0 0x20300000 0 0x1000>;
 				interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
 
@@ -568,7 +568,7 @@
 			};
 
 			sdio3: sdio@20600000 {
-				compatible  = "sprd,sdhci-r11";
+				compatible = "sprd,sdhci-r11";
 				reg = <0 0x20600000 0 0x1000>;
 				interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
 
diff --git a/arch/arm64/boot/dts/sprd/whale2.dtsi b/arch/arm64/boot/dts/sprd/whale2.dtsi
index 79b9591c37aa..fece49704b5c 100644
--- a/arch/arm64/boot/dts/sprd/whale2.dtsi
+++ b/arch/arm64/boot/dts/sprd/whale2.dtsi
@@ -126,13 +126,15 @@
 				reg = <0 0x20100000 0 0x4000>;
 				interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>;
 				#dma-cells = <1>;
+				/* For backwards compatibility: */
 				#dma-channels = <32>;
+				dma-channels = <32>;
 				clock-names = "enable";
 				clocks = <&apahb_gate CLK_DMA_EB>;
 			};
 
 			sdio3: sdio@50430000 {
-				compatible  = "sprd,sdhci-r11";
+				compatible = "sprd,sdhci-r11";
 				reg = <0 0x50430000 0 0x1000>;
 				interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
 
@@ -272,7 +274,9 @@
 				compatible = "sprd,sc9860-dma";
 				reg = <0 0x41580000 0 0x4000>;
 				#dma-cells = <1>;
+				/* For backwards compatibility: */
 				#dma-channels = <32>;
+				dma-channels = <32>;
 				clock-names = "enable", "ashb_eb";
 				clocks = <&agcp_gate CLK_AGCP_DMAAP_EB>,
 				       <&agcp_gate CLK_AGCP_AP_ASHB_EB>;
diff --git a/arch/arm64/boot/dts/synaptics/as370.dtsi b/arch/arm64/boot/dts/synaptics/as370.dtsi
deleted file mode 100644
index 4bb5d650df9c..000000000000
--- a/arch/arm64/boot/dts/synaptics/as370.dtsi
+++ /dev/null
@@ -1,173 +0,0 @@
-// SPDX-License-Identifier: (GPL-2.0 OR MIT)
-/*
- * Copyright (C) 2018 Synaptics Incorporated
- *
- * Author: Jisheng Zhang <jszhang@kernel.org>
- */
-
-#include <dt-bindings/interrupt-controller/arm-gic.h>
-
-/ {
-	compatible = "syna,as370";
-	interrupt-parent = <&gic>;
-	#address-cells = <2>;
-	#size-cells = <2>;
-
-	psci {
-		compatible = "arm,psci-1.0";
-		method = "smc";
-	};
-
-	cpus {
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		cpu0: cpu@0 {
-			compatible = "arm,cortex-a53";
-			device_type = "cpu";
-			reg = <0x0>;
-			enable-method = "psci";
-			next-level-cache = <&l2>;
-			cpu-idle-states = <&CPU_SLEEP_0>;
-		};
-
-		cpu1: cpu@1 {
-			compatible = "arm,cortex-a53";
-			device_type = "cpu";
-			reg = <0x1>;
-			enable-method = "psci";
-			next-level-cache = <&l2>;
-			cpu-idle-states = <&CPU_SLEEP_0>;
-		};
-
-		cpu2: cpu@2 {
-			compatible = "arm,cortex-a53";
-			device_type = "cpu";
-			reg = <0x2>;
-			enable-method = "psci";
-			next-level-cache = <&l2>;
-			cpu-idle-states = <&CPU_SLEEP_0>;
-		};
-
-		cpu3: cpu@3 {
-			compatible = "arm,cortex-a53";
-			device_type = "cpu";
-			reg = <0x3>;
-			enable-method = "psci";
-			next-level-cache = <&l2>;
-			cpu-idle-states = <&CPU_SLEEP_0>;
-		};
-
-		l2: cache {
-			compatible = "cache";
-		};
-
-		idle-states {
-			entry-method = "psci";
-			CPU_SLEEP_0: cpu-sleep-0 {
-				compatible = "arm,idle-state";
-				local-timer-stop;
-				arm,psci-suspend-param = <0x0010000>;
-				entry-latency-us = <75>;
-				exit-latency-us = <155>;
-				min-residency-us = <1000>;
-			};
-		};
-	};
-
-	osc: osc {
-		compatible = "fixed-clock";
-		#clock-cells = <0>;
-		clock-frequency = <25000000>;
-	};
-
-	pmu {
-		compatible = "arm,cortex-a53-pmu";
-		interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
-			     <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>,
-			     <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>,
-			     <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
-		interrupt-affinity = <&cpu0>,
-				     <&cpu1>,
-				     <&cpu2>,
-				     <&cpu3>;
-	};
-
-	timer {
-		compatible = "arm,armv8-timer";
-		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
-			     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
-			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
-			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
-	};
-
-	soc@f7000000 {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges = <0 0 0xf7000000 0x1000000>;
-
-		gic: interrupt-controller@901000 {
-			compatible = "arm,gic-400";
-			#interrupt-cells = <3>;
-			interrupt-controller;
-			reg = <0x901000 0x1000>,
-			      <0x902000 0x2000>,
-			      <0x904000 0x2000>,
-			      <0x906000 0x2000>;
-			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
-		};
-
-		apb@e80000 {
-			compatible = "simple-bus";
-			#address-cells = <1>;
-			#size-cells = <1>;
-			ranges = <0 0xe80000 0x10000>;
-
-			uart0: serial@c00 {
-				compatible = "snps,dw-apb-uart";
-				reg = <0xc00 0x100>;
-				interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>;
-				clocks = <&osc>;
-				reg-shift = <2>;
-				status = "disabled";
-			};
-
-			gpio0: gpio@1800 {
-				compatible = "snps,dw-apb-gpio";
-				reg = <0x1800 0x400>;
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				porta: gpio-port@0 {
-					compatible = "snps,dw-apb-gpio-port";
-					gpio-controller;
-					#gpio-cells = <2>;
-					ngpios = <32>;
-					reg = <0>;
-					interrupt-controller;
-					#interrupt-cells = <2>;
-					interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
-				};
-			};
-
-			gpio1: gpio@2000 {
-				compatible = "snps,dw-apb-gpio";
-				reg = <0x2000 0x400>;
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				portb: gpio-port@1 {
-					compatible = "snps,dw-apb-gpio-port";
-					gpio-controller;
-					#gpio-cells = <2>;
-					ngpios = <32>;
-					reg = <0>;
-					interrupt-controller;
-					#interrupt-cells = <2>;
-					interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
-				};
-			};
-		};
-	};
-};
diff --git a/arch/arm64/boot/dts/tesla/Makefile b/arch/arm64/boot/dts/tesla/Makefile
new file mode 100644
index 000000000000..a1ee50e2fd06
--- /dev/null
+++ b/arch/arm64/boot/dts/tesla/Makefile
@@ -0,0 +1,3 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_TESLA_FSD) += \
+	fsd-evb.dtb
diff --git a/arch/arm64/boot/dts/tesla/fsd-evb.dts b/arch/arm64/boot/dts/tesla/fsd-evb.dts
new file mode 100644
index 000000000000..1db6ddf03f01
--- /dev/null
+++ b/arch/arm64/boot/dts/tesla/fsd-evb.dts
@@ -0,0 +1,43 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+/*
+ * Tesla FSD board device tree source
+ *
+ * Copyright (c) 2017-2021 Samsung Electronics Co., Ltd.
+ *		https://www.samsung.com
+ * Copyright (c) 2017-2021 Tesla, Inc.
+ *		https://www.tesla.com
+ */
+
+/dts-v1/;
+#include "fsd.dtsi"
+
+/ {
+	model = "Tesla Full Self-Driving (FSD) Evaluation board";
+	compatible = "tesla,fsd-evb", "tesla,fsd";
+
+	aliases {
+		serial0 = &serial_0;
+		serial1 = &serial_1;
+	};
+
+	chosen {
+		stdout-path = &serial_0;
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x0 0x80000000 0x2 0x00000000>;
+	};
+};
+
+&fin_pll {
+	clock-frequency = <24000000>;
+};
+
+&serial_0 {
+	status = "okay";
+};
+
+&ufs {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/tesla/fsd-pinctrl.dtsi b/arch/arm64/boot/dts/tesla/fsd-pinctrl.dtsi
new file mode 100644
index 000000000000..d0abb9aa0e9e
--- /dev/null
+++ b/arch/arm64/boot/dts/tesla/fsd-pinctrl.dtsi
@@ -0,0 +1,349 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Tesla Full Self-Driving SoC device tree source
+ *
+ * Copyright (c) 2017-2021 Samsung Electronics Co., Ltd.
+ *		https://www.samsung.com
+ * Copyright (c) 2017-2021 Tesla, Inc.
+ *		https://www.tesla.com
+ */
+
+#include "fsd-pinctrl.h"
+
+&pinctrl_fsys0 {
+	gpf0: gpf0-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpf1: gpf1-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpf6: gpf6-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpf4: gpf4-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpf5: gpf5-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	ufs_rst_n: ufs-rst-n-pins {
+		samsung,pins = "gpf5-0";
+		samsung,pin-function = <FSD_PIN_FUNC_2>;
+		samsung,pin-pud = <FSD_PIN_PULL_NONE>;
+		samsung,pin-drv = <FSD_PIN_DRV_LV2>;
+	};
+
+	ufs_refclk_out: ufs-refclk-out-pins {
+		samsung,pins = "gpf5-1";
+		samsung,pin-function = <FSD_PIN_FUNC_2>;
+		samsung,pin-pud = <FSD_PIN_PULL_NONE>;
+		samsung,pin-drv = <FSD_PIN_DRV_LV2>;
+	};
+};
+
+&pinctrl_peric {
+	gpc8: gpc8-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpf2: gpf2-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpf3: gpf3-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpd0: gpd0-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpb0: gpb0-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpb1: gpb1-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpb4: gpb4-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpb5: gpb5-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpb6: gpb6-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpb7: gpb7-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpd1: gpd1-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpd2: gpd2-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpd3: gpd3-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpg0: gpg0-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpg1: gpg1-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpg2: gpg2-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpg3: gpg3-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpg4: gpg4-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpg5: gpg5-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpg6: gpg6-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpg7: gpg7-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	pwm0_out: pwm0-out-pins {
+		samsung,pins = "gpb6-1";
+		samsung,pin-function = <FSD_PIN_FUNC_2>;
+		samsung,pin-pud = <FSD_PIN_PULL_UP>;
+		samsung,pin-drv = <FSD_PIN_DRV_LV2>;
+	};
+
+	pwm1_out: pwm1-out-pins {
+		samsung,pins = "gpb6-5";
+		samsung,pin-function = <FSD_PIN_FUNC_2>;
+		samsung,pin-pud = <FSD_PIN_PULL_UP>;
+		samsung,pin-drv = <FSD_PIN_DRV_LV2>;
+	};
+
+	hs_i2c0_bus: hs-i2c0-bus-pins {
+		samsung,pins = "gpb0-0", "gpb0-1";
+		samsung,pin-function = <FSD_PIN_FUNC_2>;
+		samsung,pin-pud = <FSD_PIN_PULL_UP>;
+		samsung,pin-drv = <FSD_PIN_DRV_LV1>;
+	};
+
+	hs_i2c1_bus: hs-i2c1-bus-pins {
+		samsung,pins = "gpb0-2", "gpb0-3";
+		samsung,pin-function = <FSD_PIN_FUNC_2>;
+		samsung,pin-pud = <FSD_PIN_PULL_UP>;
+		samsung,pin-drv = <FSD_PIN_DRV_LV1>;
+	};
+
+	hs_i2c2_bus: hs-i2c2-bus-pins {
+		samsung,pins = "gpb0-4", "gpb0-5";
+		samsung,pin-function = <FSD_PIN_FUNC_2>;
+		samsung,pin-pud = <FSD_PIN_PULL_UP>;
+		samsung,pin-drv = <FSD_PIN_DRV_LV1>;
+	};
+
+	hs_i2c3_bus: hs-i2c3-bus-pins {
+		samsung,pins = "gpb0-6", "gpb0-7";
+		samsung,pin-function = <FSD_PIN_FUNC_2>;
+		samsung,pin-pud = <FSD_PIN_PULL_UP>;
+		samsung,pin-drv = <FSD_PIN_DRV_LV1>;
+	};
+
+	hs_i2c4_bus: hs-i2c4-bus-pins {
+		samsung,pins = "gpb1-0", "gpb1-1";
+		samsung,pin-function = <FSD_PIN_FUNC_2>;
+		samsung,pin-pud = <FSD_PIN_PULL_UP>;
+		samsung,pin-drv = <FSD_PIN_DRV_LV1>;
+	};
+
+	hs_i2c5_bus: hs-i2c5-bus-pins {
+		samsung,pins = "gpb1-2", "gpb1-3";
+		samsung,pin-function = <FSD_PIN_FUNC_2>;
+		samsung,pin-pud = <FSD_PIN_PULL_UP>;
+		samsung,pin-drv = <FSD_PIN_DRV_LV1>;
+	};
+
+	hs_i2c6_bus: hs-i2c6-bus-pins {
+		samsung,pins = "gpb1-4", "gpb1-5";
+		samsung,pin-function = <FSD_PIN_FUNC_2>;
+		samsung,pin-pud = <FSD_PIN_PULL_UP>;
+		samsung,pin-drv = <FSD_PIN_DRV_LV1>;
+	};
+
+	hs_i2c7_bus: hs-i2c7-bus-pins {
+		samsung,pins = "gpb1-6", "gpb1-7";
+		samsung,pin-function = <FSD_PIN_FUNC_2>;
+		samsung,pin-pud = <FSD_PIN_PULL_UP>;
+		samsung,pin-drv = <FSD_PIN_DRV_LV1>;
+	};
+
+	uart0_data: uart0-data-pins {
+		samsung,pins = "gpb7-0", "gpb7-1";
+		samsung,pin-function = <FSD_PIN_FUNC_2>;
+		samsung,pin-pud = <FSD_PIN_PULL_NONE>;
+		samsung,pin-drv = <FSD_PIN_DRV_LV1>;
+	};
+
+	uart1_data: uart1-data-pins {
+		samsung,pins = "gpb7-4", "gpb7-5";
+		samsung,pin-function = <FSD_PIN_FUNC_2>;
+		samsung,pin-pud = <FSD_PIN_PULL_NONE>;
+		samsung,pin-drv = <FSD_PIN_DRV_LV1>;
+	};
+
+	spi0_bus: spi0-bus-pins {
+		samsung,pins = "gpb4-0", "gpb4-2", "gpb4-3";
+		samsung,pin-function = <FSD_PIN_FUNC_2>;
+		samsung,pin-pud = <FSD_PIN_PULL_UP>;
+		samsung,pin-drv = <FSD_PIN_DRV_LV1>;
+	};
+
+	spi1_bus: spi1-bus-pins {
+		samsung,pins = "gpb4-4", "gpb4-6", "gpb4-7";
+		samsung,pin-function = <FSD_PIN_FUNC_2>;
+		samsung,pin-pud = <FSD_PIN_PULL_UP>;
+		samsung,pin-drv = <FSD_PIN_DRV_LV1>;
+	};
+
+	spi2_bus: spi2-bus-pins {
+		samsung,pins = "gpb5-0", "gpb5-2", "gpb5-3";
+		samsung,pin-function = <FSD_PIN_FUNC_2>;
+		samsung,pin-pud = <FSD_PIN_PULL_UP>;
+		samsung,pin-drv = <FSD_PIN_DRV_LV1>;
+	};
+};
+
+&pinctrl_pmu {
+	gpq0: gpq0-gpio-bank {
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+};
diff --git a/arch/arm64/boot/dts/tesla/fsd-pinctrl.h b/arch/arm64/boot/dts/tesla/fsd-pinctrl.h
new file mode 100644
index 000000000000..6ffbda362493
--- /dev/null
+++ b/arch/arm64/boot/dts/tesla/fsd-pinctrl.h
@@ -0,0 +1,33 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Tesla FSD DTS pinctrl constants
+ *
+ * Copyright (c) 2016 Samsung Electronics Co., Ltd.
+ *		http://www.samsung.com
+ * Copyright (c) 2022 Linaro Ltd
+ * Author: Krzysztof Kozlowski <krzk@kernel.org>
+ */
+
+#ifndef __DTS_ARM64_TESLA_FSD_PINCTRL_H__
+#define __DTS_ARM64_TESLA_FSD_PINCTRL_H__
+
+#define FSD_PIN_PULL_NONE		0
+#define FSD_PIN_PULL_DOWN		1
+#define FSD_PIN_PULL_UP			3
+
+#define FSD_PIN_DRV_LV1			0
+#define FSD_PIN_DRV_LV2			2
+#define FSD_PIN_DRV_LV3			1
+#define FSD_PIN_DRV_LV4			3
+
+#define FSD_PIN_FUNC_INPUT		0
+#define FSD_PIN_FUNC_OUTPUT		1
+#define FSD_PIN_FUNC_2			2
+#define FSD_PIN_FUNC_3			3
+#define FSD_PIN_FUNC_4			4
+#define FSD_PIN_FUNC_5			5
+#define FSD_PIN_FUNC_6			6
+#define FSD_PIN_FUNC_EINT		0xf
+#define FSD_PIN_FUNC_F			FSD_PIN_FUNC_EINT
+
+#endif /* __DTS_ARM64_TESLA_FSD_PINCTRL_H__ */
diff --git a/arch/arm64/boot/dts/tesla/fsd.dtsi b/arch/arm64/boot/dts/tesla/fsd.dtsi
new file mode 100644
index 000000000000..f35bc5a288c2
--- /dev/null
+++ b/arch/arm64/boot/dts/tesla/fsd.dtsi
@@ -0,0 +1,866 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Tesla Full Self-Driving SoC device tree source
+ *
+ * Copyright (c) 2017-2022 Samsung Electronics Co., Ltd.
+ *		https://www.samsung.com
+ * Copyright (c) 2017-2022 Tesla, Inc.
+ *		https://www.tesla.com
+ */
+
+#include <dt-bindings/clock/fsd-clk.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+/ {
+	compatible = "tesla,fsd";
+	interrupt-parent = <&gic>;
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	aliases {
+		i2c0 = &hsi2c_0;
+		i2c1 = &hsi2c_1;
+		i2c2 = &hsi2c_2;
+		i2c3 = &hsi2c_3;
+		i2c4 = &hsi2c_4;
+		i2c5 = &hsi2c_5;
+		i2c6 = &hsi2c_6;
+		i2c7 = &hsi2c_7;
+		pinctrl0 = &pinctrl_fsys0;
+		pinctrl1 = &pinctrl_peric;
+		pinctrl2 = &pinctrl_pmu;
+		spi0 = &spi_0;
+		spi1 = &spi_1;
+		spi2 = &spi_2;
+	};
+
+	cpus {
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		cpu-map {
+			cluster0 {
+				core0 {
+					cpu = <&cpucl0_0>;
+				};
+				core1 {
+					cpu = <&cpucl0_1>;
+				};
+				core2 {
+					cpu = <&cpucl0_2>;
+				};
+				core3 {
+					cpu = <&cpucl0_3>;
+				};
+			};
+
+			cluster1 {
+				core0 {
+					cpu = <&cpucl1_0>;
+				};
+				core1 {
+					cpu = <&cpucl1_1>;
+				};
+				core2 {
+					cpu = <&cpucl1_2>;
+				};
+				core3 {
+					cpu = <&cpucl1_3>;
+				};
+			};
+
+			cluster2 {
+				core0 {
+					cpu = <&cpucl2_0>;
+				};
+				core1 {
+					cpu = <&cpucl2_1>;
+				};
+				core2 {
+					cpu = <&cpucl2_2>;
+				};
+				core3 {
+					cpu = <&cpucl2_3>;
+				};
+			};
+		};
+
+		/* Cluster 0 */
+		cpucl0_0: cpu@0 {
+				device_type = "cpu";
+				compatible = "arm,cortex-a72";
+				reg = <0x0 0x000>;
+				enable-method = "psci";
+				clock-frequency = <2400000000>;
+				cpu-idle-states = <&CPU_SLEEP>;
+				i-cache-size = <0xc000>;
+				i-cache-line-size = <64>;
+				i-cache-sets = <256>;
+				d-cache-size = <0x8000>;
+				d-cache-line-size = <64>;
+				d-cache-sets = <256>;
+				next-level-cache = <&cpucl_l2>;
+		};
+
+		cpucl0_1: cpu@1 {
+				device_type = "cpu";
+				compatible = "arm,cortex-a72";
+				reg = <0x0 0x001>;
+				enable-method = "psci";
+				clock-frequency = <2400000000>;
+				cpu-idle-states = <&CPU_SLEEP>;
+				i-cache-size = <0xc000>;
+				i-cache-line-size = <64>;
+				i-cache-sets = <256>;
+				d-cache-size = <0x8000>;
+				d-cache-line-size = <64>;
+				d-cache-sets = <256>;
+				next-level-cache = <&cpucl_l2>;
+		};
+
+		cpucl0_2: cpu@2 {
+				device_type = "cpu";
+				compatible = "arm,cortex-a72";
+				reg = <0x0 0x002>;
+				enable-method = "psci";
+				clock-frequency = <2400000000>;
+				cpu-idle-states = <&CPU_SLEEP>;
+				i-cache-size = <0xc000>;
+				i-cache-line-size = <64>;
+				i-cache-sets = <256>;
+				d-cache-size = <0x8000>;
+				d-cache-line-size = <64>;
+				d-cache-sets = <256>;
+				next-level-cache = <&cpucl_l2>;
+		};
+
+		cpucl0_3: cpu@3 {
+				device_type = "cpu";
+				compatible = "arm,cortex-a72";
+				reg = <0x0 0x003>;
+				enable-method = "psci";
+				cpu-idle-states = <&CPU_SLEEP>;
+				i-cache-size = <0xc000>;
+				i-cache-line-size = <64>;
+				i-cache-sets = <256>;
+				d-cache-size = <0x8000>;
+				d-cache-line-size = <64>;
+				d-cache-sets = <256>;
+				next-level-cache = <&cpucl_l2>;
+		};
+
+		/* Cluster 1 */
+		cpucl1_0: cpu@100 {
+				device_type = "cpu";
+				compatible = "arm,cortex-a72";
+				reg = <0x0 0x100>;
+				enable-method = "psci";
+				clock-frequency = <2400000000>;
+				cpu-idle-states = <&CPU_SLEEP>;
+				i-cache-size = <0xc000>;
+				i-cache-line-size = <64>;
+				i-cache-sets = <256>;
+				d-cache-size = <0x8000>;
+				d-cache-line-size = <64>;
+				d-cache-sets = <256>;
+				next-level-cache = <&cpucl_l2>;
+		};
+
+		cpucl1_1: cpu@101 {
+				device_type = "cpu";
+				compatible = "arm,cortex-a72";
+				reg = <0x0 0x101>;
+				enable-method = "psci";
+				clock-frequency = <2400000000>;
+				cpu-idle-states = <&CPU_SLEEP>;
+				i-cache-size = <0xc000>;
+				i-cache-line-size = <64>;
+				i-cache-sets = <256>;
+				d-cache-size = <0x8000>;
+				d-cache-line-size = <64>;
+				d-cache-sets = <256>;
+				next-level-cache = <&cpucl_l2>;
+		};
+
+		cpucl1_2: cpu@102 {
+				device_type = "cpu";
+				compatible = "arm,cortex-a72";
+				reg = <0x0 0x102>;
+				enable-method = "psci";
+				clock-frequency = <2400000000>;
+				cpu-idle-states = <&CPU_SLEEP>;
+				i-cache-size = <0xc000>;
+				i-cache-line-size = <64>;
+				i-cache-sets = <256>;
+				d-cache-size = <0x8000>;
+				d-cache-line-size = <64>;
+				d-cache-sets = <256>;
+				next-level-cache = <&cpucl_l2>;
+		};
+
+		cpucl1_3: cpu@103 {
+				device_type = "cpu";
+				compatible = "arm,cortex-a72";
+				reg = <0x0 0x103>;
+				enable-method = "psci";
+				clock-frequency = <2400000000>;
+				cpu-idle-states = <&CPU_SLEEP>;
+				i-cache-size = <0xc000>;
+				i-cache-line-size = <64>;
+				i-cache-sets = <256>;
+				d-cache-size = <0x8000>;
+				d-cache-line-size = <64>;
+				d-cache-sets = <256>;
+				next-level-cache = <&cpucl_l2>;
+		};
+
+		/* Cluster 2 */
+		cpucl2_0: cpu@200 {
+				device_type = "cpu";
+				compatible = "arm,cortex-a72";
+				reg = <0x0 0x200>;
+				enable-method = "psci";
+				clock-frequency = <2400000000>;
+				cpu-idle-states = <&CPU_SLEEP>;
+				i-cache-size = <0xc000>;
+				i-cache-line-size = <64>;
+				i-cache-sets = <256>;
+				d-cache-size = <0x8000>;
+				d-cache-line-size = <64>;
+				d-cache-sets = <256>;
+				next-level-cache = <&cpucl_l2>;
+		};
+
+		cpucl2_1: cpu@201 {
+				device_type = "cpu";
+				compatible = "arm,cortex-a72";
+				reg = <0x0 0x201>;
+				enable-method = "psci";
+				clock-frequency = <2400000000>;
+				cpu-idle-states = <&CPU_SLEEP>;
+				i-cache-size = <0xc000>;
+				i-cache-line-size = <64>;
+				i-cache-sets = <256>;
+				d-cache-size = <0x8000>;
+				d-cache-line-size = <64>;
+				d-cache-sets = <256>;
+				next-level-cache = <&cpucl_l2>;
+		};
+
+		cpucl2_2: cpu@202 {
+				device_type = "cpu";
+				compatible = "arm,cortex-a72";
+				reg = <0x0 0x202>;
+				enable-method = "psci";
+				clock-frequency = <2400000000>;
+				cpu-idle-states = <&CPU_SLEEP>;
+				i-cache-size = <0xc000>;
+				i-cache-line-size = <64>;
+				i-cache-sets = <256>;
+				d-cache-size = <0x8000>;
+				d-cache-line-size = <64>;
+				d-cache-sets = <256>;
+				next-level-cache = <&cpucl_l2>;
+		};
+
+		cpucl2_3: cpu@203 {
+				device_type = "cpu";
+				compatible = "arm,cortex-a72";
+				reg = <0x0 0x203>;
+				enable-method = "psci";
+				clock-frequency = <2400000000>;
+				cpu-idle-states = <&CPU_SLEEP>;
+				i-cache-size = <0xc000>;
+				i-cache-line-size = <64>;
+				i-cache-sets = <256>;
+				d-cache-size = <0x8000>;
+				d-cache-line-size = <64>;
+				d-cache-sets = <256>;
+				next-level-cache = <&cpucl_l2>;
+		};
+
+		cpucl_l2: l2-cache0 {
+			compatible = "cache";
+			cache-size = <0x400000>;
+			cache-line-size = <64>;
+			cache-sets = <4096>;
+		};
+
+		idle-states {
+			entry-method = "psci";
+
+			CPU_SLEEP: cpu-sleep {
+				idle-state-name = "c2";
+				compatible = "arm,idle-state";
+				local-timer-stop;
+				arm,psci-suspend-param = <0x0010000>;
+				entry-latency-us = <30>;
+				exit-latency-us = <75>;
+				min-residency-us = <300>;
+			};
+		};
+	};
+
+	arm-pmu {
+		compatible = "arm,armv8-pmuv3";
+		interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 359 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 370 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 371 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 372 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 373 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 384 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 385 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 386 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 387 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-affinity = <&cpucl0_0>, <&cpucl0_1>, <&cpucl0_2>,
+				     <&cpucl0_3>, <&cpucl1_0>, <&cpucl1_1>,
+				     <&cpucl1_2>, <&cpucl1_3>, <&cpucl2_0>,
+				     <&cpucl2_1>, <&cpucl2_2>, <&cpucl2_3>;
+	};
+
+	psci {
+		compatible = "arm,psci-1.0";
+		method = "smc";
+	};
+
+	timer {
+		compatible = "arm,armv8-timer";
+		interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW>,
+			     <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW>,
+			     <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW>,
+			     <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW>;
+	};
+
+	fin_pll: clock {
+		compatible = "fixed-clock";
+		clock-output-names = "fin_pll";
+		#clock-cells = <0>;
+	};
+
+	soc: soc@0 {
+		compatible = "simple-bus";
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges = <0x0 0x0 0x0 0x0 0x0 0x18000000>;
+		dma-ranges = <0x0 0x0 0x0 0x0 0x10 0x0>;
+
+		gic: interrupt-controller@10400000 {
+			compatible = "arm,gic-v3";
+			#interrupt-cells = <3>;
+			interrupt-controller;
+			reg =	<0x0 0x10400000 0x0 0x10000>, /* GICD */
+				<0x0 0x10600000 0x0 0x200000>; /* GICR_RD+GICR_SGI */
+			interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		smmu_imem: iommu@10200000 {
+			compatible = "arm,mmu-500";
+			reg = <0x0 0x10200000 0x0 0x10000>;
+			#iommu-cells = <2>;
+			#global-interrupts = <7>;
+			interrupts = <GIC_SPI 438 IRQ_TYPE_LEVEL_HIGH>, /* Global secure fault */
+				     <GIC_SPI 439 IRQ_TYPE_LEVEL_HIGH>, /* Global non-secure fault */
+				     <GIC_SPI 451 IRQ_TYPE_LEVEL_HIGH>, /* Combined secure interrupt */
+				     <GIC_SPI 450 IRQ_TYPE_LEVEL_HIGH>, /* Combined non-secure interrupt */
+				     /* Performance counter interrupts */
+				     <GIC_SPI 441 IRQ_TYPE_LEVEL_HIGH>, /* for FSYS1_0 */
+				     <GIC_SPI 442 IRQ_TYPE_LEVEL_HIGH>, /* for FSYS1_1 */
+				     <GIC_SPI 443 IRQ_TYPE_LEVEL_HIGH>, /* for IMEM_0  */
+				     /* Per context non-secure context interrupts, 0-3 interrupts */
+				     <GIC_SPI 446 IRQ_TYPE_LEVEL_HIGH>, /* for CONTEXT_0 */
+				     <GIC_SPI 447 IRQ_TYPE_LEVEL_HIGH>, /* for CONTEXT_1 */
+				     <GIC_SPI 448 IRQ_TYPE_LEVEL_HIGH>, /* for CONTEXT_2 */
+				     <GIC_SPI 449 IRQ_TYPE_LEVEL_HIGH>; /* for CONTEXT_3 */
+		};
+
+		smmu_isp: iommu@12100000 {
+			compatible = "arm,mmu-500";
+			reg = <0x0 0x12100000 0x0 0x10000>;
+			#iommu-cells = <2>;
+			#global-interrupts = <11>;
+			interrupts = <GIC_SPI 321 IRQ_TYPE_LEVEL_HIGH>, /* Global secure fault */
+				     <GIC_SPI 322 IRQ_TYPE_LEVEL_HIGH>, /* Global non-secure fault */
+				     <GIC_SPI 346 IRQ_TYPE_LEVEL_HIGH>, /* Combined secure interrupt */
+				     <GIC_SPI 345 IRQ_TYPE_LEVEL_HIGH>, /* Combined non-secure interrupt */
+				     /* Performance counter interrupts */
+				     <GIC_SPI 323 IRQ_TYPE_LEVEL_HIGH>, /* for CAM_CSI   */
+				     <GIC_SPI 324 IRQ_TYPE_LEVEL_HIGH>, /* for CAM_DP_0  */
+				     <GIC_SPI 325 IRQ_TYPE_LEVEL_HIGH>, /* for CAM_DP_1  */
+				     <GIC_SPI 326 IRQ_TYPE_LEVEL_HIGH>, /* for CAM_ISP_0 */
+				     <GIC_SPI 327 IRQ_TYPE_LEVEL_HIGH>, /* for CAM_ISP_1 */
+				     <GIC_SPI 328 IRQ_TYPE_LEVEL_HIGH>, /* for CAM_MFC_0 */
+				     <GIC_SPI 329 IRQ_TYPE_LEVEL_HIGH>, /* for CAM_MFC_1 */
+				     /* Per context non-secure context interrupts, 0-7 interrupts */
+				     <GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH>, /* for CONTEXT_0 */
+				     <GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH>, /* for CONTEXT_1 */
+				     <GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH>, /* for CONTEXT_2 */
+				     <GIC_SPI 333 IRQ_TYPE_LEVEL_HIGH>, /* for CONTEXT_3 */
+				     <GIC_SPI 334 IRQ_TYPE_LEVEL_HIGH>, /* for CONTEXT_4 */
+				     <GIC_SPI 335 IRQ_TYPE_LEVEL_HIGH>, /* for CONTEXT_5 */
+				     <GIC_SPI 336 IRQ_TYPE_LEVEL_HIGH>, /* for CONTEXT_6 */
+				     <GIC_SPI 337 IRQ_TYPE_LEVEL_HIGH>; /* for CONTEXT_7 */
+		};
+
+		smmu_peric: iommu@14900000 {
+			compatible = "arm,mmu-500";
+			reg = <0x0 0x14900000 0x0 0x10000>;
+			#iommu-cells = <2>;
+			#global-interrupts = <5>;
+			interrupts = <GIC_SPI 197 IRQ_TYPE_LEVEL_HIGH>, /* Global secure fault */
+				     <GIC_SPI 196 IRQ_TYPE_LEVEL_HIGH>, /* Global non-secure fault */
+				     <GIC_SPI 193 IRQ_TYPE_LEVEL_HIGH>, /* Combined secure interrupt */
+				     <GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>, /* Combined non-secure interrupt */
+				     /* Performance counter interrupts */
+				     <GIC_SPI 198 IRQ_TYPE_LEVEL_HIGH>, /* for PERIC */
+				     /* Per context non-secure context interrupts, 0-1 interrupts */
+				     <GIC_SPI 194 IRQ_TYPE_LEVEL_HIGH>, /* for CONTEXT_0 */
+				     <GIC_SPI 195 IRQ_TYPE_LEVEL_HIGH>; /* for CONTEXT_1 */
+		};
+
+		smmu_fsys0: iommu@15450000 {
+			compatible = "arm,mmu-500";
+			reg = <0x0 0x15450000 0x0 0x10000>;
+			#iommu-cells = <2>;
+			#global-interrupts = <5>;
+			interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>, /* Global secure fault */
+				     <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>, /* Global non-secure fault */
+				     <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>, /* Combined secure interrupt */
+				     <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>, /* Combined non-secure interrupt */
+				     /* Performance counter interrupts */
+				     <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>, /* for FSYS0   */
+				     /* Per context non-secure context interrupts, 0-1 interrupts */
+				     <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>, /* for CONTEXT_0 */
+				     <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; /* for CONTEXT_1 */
+		};
+
+		clock_imem: clock-controller@10010000 {
+			compatible = "tesla,fsd-clock-imem";
+			reg = <0x0 0x10010000 0x0 0x3000>;
+			#clock-cells = <1>;
+			clocks = <&fin_pll>,
+				<&clock_cmu DOUT_CMU_IMEM_TCUCLK>,
+				<&clock_cmu DOUT_CMU_IMEM_ACLK>,
+				<&clock_cmu DOUT_CMU_IMEM_DMACLK>;
+			clock-names = "fin_pll",
+				"dout_cmu_imem_tcuclk",
+				"dout_cmu_imem_aclk",
+				"dout_cmu_imem_dmaclk";
+		};
+
+		clock_cmu: clock-controller@11c10000 {
+			compatible = "tesla,fsd-clock-cmu";
+			reg = <0x0 0x11c10000 0x0 0x3000>;
+			#clock-cells = <1>;
+			clocks = <&fin_pll>;
+			clock-names = "fin_pll";
+		};
+
+		clock_csi: clock-controller@12610000 {
+			compatible = "tesla,fsd-clock-cam_csi";
+			reg = <0x0 0x12610000 0x0 0x3000>;
+			#clock-cells = <1>;
+			clocks = <&fin_pll>;
+			clock-names = "fin_pll";
+		};
+
+		clock_mfc: clock-controller@12810000 {
+			compatible = "tesla,fsd-clock-mfc";
+			reg = <0x0 0x12810000 0x0 0x3000>;
+			#clock-cells = <1>;
+			clocks = <&fin_pll>;
+			clock-names = "fin_pll";
+		};
+
+		clock_peric: clock-controller@14010000 {
+			compatible = "tesla,fsd-clock-peric";
+			reg = <0x0 0x14010000 0x0 0x3000>;
+			#clock-cells = <1>;
+			clocks = <&fin_pll>,
+				<&clock_cmu DOUT_CMU_PLL_SHARED0_DIV4>,
+				<&clock_cmu DOUT_CMU_PERIC_SHARED1DIV36>,
+				<&clock_cmu DOUT_CMU_PERIC_SHARED0DIV3_TBUCLK>,
+				<&clock_cmu DOUT_CMU_PERIC_SHARED0DIV20>,
+				<&clock_cmu DOUT_CMU_PERIC_SHARED1DIV4_DMACLK>;
+			clock-names = "fin_pll",
+				"dout_cmu_pll_shared0_div4",
+				"dout_cmu_peric_shared1div36",
+				"dout_cmu_peric_shared0div3_tbuclk",
+				"dout_cmu_peric_shared0div20",
+				"dout_cmu_peric_shared1div4_dmaclk";
+		};
+
+		clock_fsys0: clock-controller@15010000 {
+			compatible = "tesla,fsd-clock-fsys0";
+			reg = <0x0 0x15010000 0x0 0x3000>;
+			#clock-cells = <1>;
+			clocks = <&fin_pll>,
+				<&clock_cmu DOUT_CMU_PLL_SHARED0_DIV6>,
+				<&clock_cmu DOUT_CMU_FSYS0_SHARED1DIV4>,
+				<&clock_cmu DOUT_CMU_FSYS0_SHARED0DIV4>;
+			clock-names = "fin_pll",
+				"dout_cmu_pll_shared0_div6",
+				"dout_cmu_fsys0_shared1div4",
+				"dout_cmu_fsys0_shared0div4";
+		};
+
+		clock_fsys1: clock-controller@16810000 {
+			compatible = "tesla,fsd-clock-fsys1";
+			reg = <0x0 0x16810000 0x0 0x3000>;
+			#clock-cells = <1>;
+			clocks = <&fin_pll>,
+				<&clock_cmu DOUT_CMU_FSYS1_SHARED0DIV8>,
+				<&clock_cmu DOUT_CMU_FSYS1_SHARED0DIV4>;
+			clock-names = "fin_pll",
+				"dout_cmu_fsys1_shared0div8",
+				"dout_cmu_fsys1_shared0div4";
+		};
+
+		mdma0: dma-controller@10100000 {
+			compatible = "arm,pl330", "arm,primecell";
+			reg = <0x0 0x10100000 0x0 0x1000>;
+			interrupts = <GIC_SPI 424 IRQ_TYPE_LEVEL_HIGH>;
+			#dma-cells = <1>;
+			clocks = <&clock_imem IMEM_DMA0_IPCLKPORT_ACLK>;
+			clock-names = "apb_pclk";
+			iommus = <&smmu_imem 0x800 0x0>;
+		};
+
+		mdma1: dma-controller@10110000 {
+			compatible = "arm,pl330", "arm,primecell";
+			reg = <0x0 0x10110000 0x0 0x1000>;
+			interrupts = <GIC_SPI 425 IRQ_TYPE_LEVEL_HIGH>;
+			#dma-cells = <1>;
+			clocks = <&clock_imem IMEM_DMA1_IPCLKPORT_ACLK>;
+			clock-names = "apb_pclk";
+			iommus = <&smmu_imem 0x801 0x0>;
+		};
+
+		pdma0: dma-controller@14280000 {
+			compatible = "arm,pl330", "arm,primecell";
+			reg = <0x0 0x14280000 0x0 0x1000>;
+			interrupts = <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>;
+			#dma-cells = <1>;
+			clocks = <&clock_peric PERIC_DMA0_IPCLKPORT_ACLK>;
+			clock-names = "apb_pclk";
+			iommus = <&smmu_peric 0x2 0x0>;
+		};
+
+		pdma1: dma-controller@14290000 {
+			compatible = "arm,pl330", "arm,primecell";
+			reg = <0x0 0x14290000 0x0 0x1000>;
+			interrupts = <GIC_SPI 191 IRQ_TYPE_LEVEL_HIGH>;
+			#dma-cells = <1>;
+			clocks = <&clock_peric PERIC_DMA1_IPCLKPORT_ACLK>;
+			clock-names = "apb_pclk";
+			iommus = <&smmu_peric 0x1 0x0>;
+		};
+
+		serial_0: serial@14180000 {
+			compatible = "samsung,exynos4210-uart";
+			reg = <0x0 0x14180000 0x0 0x100>;
+			interrupts = <GIC_SPI 171 IRQ_TYPE_LEVEL_HIGH>;
+			dmas = <&pdma1 1>, <&pdma1 0>;
+			dma-names = "rx", "tx";
+			clocks = <&clock_peric PERIC_PCLK_UART0>,
+				 <&clock_peric PERIC_SCLK_UART0>;
+			clock-names = "uart", "clk_uart_baud0";
+			status = "disabled";
+		};
+
+		serial_1: serial@14190000 {
+			compatible = "samsung,exynos4210-uart";
+			reg = <0x0 0x14190000 0x0 0x100>;
+			interrupts = <GIC_SPI 172 IRQ_TYPE_LEVEL_HIGH>;
+			dmas = <&pdma1 3>, <&pdma1 2>;
+			dma-names = "rx", "tx";
+			clocks = <&clock_peric PERIC_PCLK_UART1>,
+				 <&clock_peric PERIC_SCLK_UART1>;
+			clock-names = "uart", "clk_uart_baud0";
+			status = "disabled";
+		};
+
+		pmu_system_controller: system-controller@11400000 {
+			compatible = "samsung,exynos7-pmu", "syscon";
+			reg = <0x0 0x11400000 0x0 0x5000>;
+		};
+
+		watchdog_0: watchdog@100a0000 {
+			compatible = "samsung,exynos7-wdt";
+			reg = <0x0 0x100a0000 0x0 0x100>;
+			interrupts = <GIC_SPI 471 IRQ_TYPE_LEVEL_HIGH>;
+			samsung,syscon-phandle = <&pmu_system_controller>;
+			clocks = <&fin_pll>;
+			clock-names = "watchdog";
+		};
+
+		watchdog_1: watchdog@100b0000 {
+			compatible = "samsung,exynos7-wdt";
+			reg = <0x0 0x100b0000 0x0 0x100>;
+			interrupts = <GIC_SPI 472 IRQ_TYPE_LEVEL_HIGH>;
+			samsung,syscon-phandle = <&pmu_system_controller>;
+			clocks = <&fin_pll>;
+			clock-names = "watchdog";
+		};
+
+		watchdog_2: watchdog@100c0000 {
+			compatible = "samsung,exynos7-wdt";
+			reg = <0x0 0x100c0000 0x0 0x100>;
+			interrupts = <GIC_SPI 473 IRQ_TYPE_LEVEL_HIGH>;
+			samsung,syscon-phandle = <&pmu_system_controller>;
+			clocks = <&fin_pll>;
+			clock-names = "watchdog";
+		};
+
+		pwm_0: pwm@14100000 {
+			compatible = "samsung,exynos4210-pwm";
+			reg = <0x0 0x14100000 0x0 0x100>;
+			samsung,pwm-outputs = <0>, <1>, <2>, <3>;
+			#pwm-cells = <3>;
+			clocks = <&clock_peric PERIC_PWM0_IPCLKPORT_I_PCLK_S0>;
+			clock-names = "timers";
+			status = "disabled";
+		};
+
+		pwm_1: pwm@14110000 {
+			compatible = "samsung,exynos4210-pwm";
+			reg = <0x0 0x14110000 0x0 0x100>;
+			samsung,pwm-outputs = <0>, <1>, <2>, <3>;
+			#pwm-cells = <3>;
+			clocks = <&clock_peric PERIC_PWM1_IPCLKPORT_I_PCLK_S0>;
+			clock-names = "timers";
+			status = "disabled";
+		};
+
+		hsi2c_0: i2c@14200000 {
+			compatible = "samsung,exynos7-hsi2c";
+			reg = <0x0 0x14200000 0x0 0x1000>;
+			interrupts = <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&hs_i2c0_bus>;
+			clocks = <&clock_peric PERIC_PCLK_HSI2C0>;
+			clock-names = "hsi2c";
+			status = "disabled";
+		};
+
+		hsi2c_1: i2c@14210000 {
+			compatible = "samsung,exynos7-hsi2c";
+			reg = <0x0 0x14210000 0x0 0x1000>;
+			interrupts = <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&hs_i2c1_bus>;
+			clocks = <&clock_peric PERIC_PCLK_HSI2C1>;
+			clock-names = "hsi2c";
+			status = "disabled";
+		};
+
+		hsi2c_2: i2c@14220000 {
+			compatible = "samsung,exynos7-hsi2c";
+			reg = <0x0 0x14220000 0x0 0x1000>;
+			interrupts = <GIC_SPI 150 IRQ_TYPE_LEVEL_HIGH>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&hs_i2c2_bus>;
+			clocks = <&clock_peric PERIC_PCLK_HSI2C2>;
+			clock-names = "hsi2c";
+			status = "disabled";
+		};
+
+		hsi2c_3: i2c@14230000 {
+			compatible = "samsung,exynos7-hsi2c";
+			reg = <0x0 0x14230000 0x0 0x1000>;
+			interrupts = <GIC_SPI 151 IRQ_TYPE_LEVEL_HIGH>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&hs_i2c3_bus>;
+			clocks = <&clock_peric PERIC_PCLK_HSI2C3>;
+			clock-names = "hsi2c";
+			status = "disabled";
+		};
+
+		hsi2c_4: i2c@14240000 {
+			compatible = "samsung,exynos7-hsi2c";
+			reg = <0x0 0x14240000 0x0 0x1000>;
+			interrupts = <GIC_SPI 152 IRQ_TYPE_LEVEL_HIGH>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&hs_i2c4_bus>;
+			clocks = <&clock_peric PERIC_PCLK_HSI2C4>;
+			clock-names = "hsi2c";
+			status = "disabled";
+		};
+
+		hsi2c_5: i2c@14250000 {
+			compatible = "samsung,exynos7-hsi2c";
+			reg = <0x0 0x14250000 0x0 0x1000>;
+			interrupts = <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&hs_i2c5_bus>;
+			clocks = <&clock_peric PERIC_PCLK_HSI2C5>;
+			clock-names = "hsi2c";
+			status = "disabled";
+		};
+
+		hsi2c_6: i2c@14260000 {
+			compatible = "samsung,exynos7-hsi2c";
+			reg = <0x0 0x14260000 0x0 0x1000>;
+			interrupts = <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&hs_i2c6_bus>;
+			clocks = <&clock_peric PERIC_PCLK_HSI2C6>;
+			clock-names = "hsi2c";
+			status = "disabled";
+		};
+
+		hsi2c_7: i2c@14270000 {
+			compatible = "samsung,exynos7-hsi2c";
+			reg = <0x0 0x14270000 0x0 0x1000>;
+			interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&hs_i2c7_bus>;
+			clocks = <&clock_peric PERIC_PCLK_HSI2C7>;
+			clock-names = "hsi2c";
+			status = "disabled";
+		};
+
+		pinctrl_pmu: pinctrl@114f0000 {
+			compatible = "tesla,fsd-pinctrl";
+			reg = <0x0 0x114f0000 0x0 0x1000>;
+		};
+
+		pinctrl_peric: pinctrl@141f0000 {
+			compatible = "tesla,fsd-pinctrl";
+			reg = <0x0 0x141f0000 0x0 0x1000>;
+			interrupts = <GIC_SPI 189 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		pinctrl_fsys0: pinctrl@15020000 {
+			compatible = "tesla,fsd-pinctrl";
+			reg = <0x0 0x15020000 0x0 0x1000>;
+			interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		spi_0: spi@14140000 {
+			compatible = "tesla,fsd-spi";
+			reg = <0x0 0x14140000 0x0 0x100>;
+			interrupts = <GIC_SPI 156 IRQ_TYPE_LEVEL_HIGH>;
+			dmas = <&pdma1 4>, <&pdma1 5>;
+			dma-names = "tx", "rx";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			clocks = <&clock_peric PERIC_PCLK_SPI0>,
+				<&clock_peric PERIC_SCLK_SPI0>;
+			clock-names = "spi", "spi_busclk0";
+			samsung,spi-src-clk = <0>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&spi0_bus>;
+			num-cs = <1>;
+			status = "disabled";
+		};
+
+		spi_1: spi@14150000 {
+			compatible = "tesla,fsd-spi";
+			reg = <0x0 0x14150000 0x0 0x100>;
+			interrupts = <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>;
+			dmas = <&pdma1 6>, <&pdma1 7>;
+			dma-names = "tx", "rx";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			clocks = <&clock_peric PERIC_PCLK_SPI1>,
+				<&clock_peric PERIC_SCLK_SPI1>;
+			clock-names = "spi", "spi_busclk0";
+			samsung,spi-src-clk = <0>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&spi1_bus>;
+			num-cs = <1>;
+			status = "disabled";
+		};
+
+		spi_2: spi@14160000 {
+			compatible = "tesla,fsd-spi";
+			reg = <0x0 0x14160000 0x0 0x100>;
+			interrupts = <GIC_SPI 158 IRQ_TYPE_LEVEL_HIGH>;
+			dmas = <&pdma1 8>, <&pdma1 9>;
+			dma-names = "tx", "rx";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			clocks = <&clock_peric PERIC_PCLK_SPI2>,
+				<&clock_peric PERIC_SCLK_SPI2>;
+			clock-names = "spi", "spi_busclk0";
+			samsung,spi-src-clk = <0>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&spi2_bus>;
+			num-cs = <1>;
+			status = "disabled";
+		};
+
+		timer@10040000 {
+			compatible = "tesla,fsd-mct", "samsung,exynos4210-mct";
+			reg = <0x0 0x10040000 0x0 0x800>;
+			interrupts = <GIC_SPI 455 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 456 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 457 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 458 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 459 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 460 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 461 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 462 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 463 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 464 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 465 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 466 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 467 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 468 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 469 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 470 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&fin_pll>, <&clock_imem IMEM_MCT_PCLK>;
+			clock-names = "fin_pll", "mct";
+		};
+
+		ufs: ufs@15120000 {
+			compatible = "tesla,fsd-ufs";
+			reg = <0x0 0x15120000 0x0 0x200>,  /* 0: HCI standard */
+			      <0x0 0x15121100 0x0 0x200>,  /* 1: Vendor specified */
+			      <0x0 0x15110000 0x0 0x8000>,  /* 2: UNIPRO */
+			      <0x0 0x15130000 0x0 0x100>;  /* 3: UFS protector */
+			reg-names = "hci", "vs_hci", "unipro", "ufsp";
+			interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clock_fsys0 UFS0_TOP0_HCLK_BUS>,
+				 <&clock_fsys0 UFS0_TOP0_CLK_UNIPRO>;
+			clock-names = "core_clk", "sclk_unipro_main";
+			freq-table-hz = <0 0>, <0 0>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&ufs_rst_n &ufs_refclk_out>;
+			phys = <&ufs_phy>;
+			phy-names = "ufs-phy";
+			status = "disabled";
+		};
+
+		ufs_phy: ufs-phy@15124000 {
+			compatible = "tesla,fsd-ufs-phy";
+			reg = <0x0 0x15124000 0x0 0x800>;
+			reg-names = "phy-pma";
+			samsung,pmu-syscon = <&pmu_system_controller>;
+			#phy-cells = <0>;
+			clocks = <&clock_fsys0 UFS0_MPHY_REFCLK_IXTAL26>;
+			clock-names = "ref_clk";
+		};
+	};
+};
+
+#include "fsd-pinctrl.dtsi"
diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile
index 71f6097d4621..4555a5be2257 100644
--- a/arch/arm64/boot/dts/ti/Makefile
+++ b/arch/arm64/boot/dts/ti/Makefile
@@ -17,5 +17,11 @@ dtb-$(CONFIG_ARCH_K3) += k3-j721e-sk.dtb
 
 dtb-$(CONFIG_ARCH_K3) += k3-j7200-common-proc-board.dtb
 
+dtb-$(CONFIG_ARCH_K3) += k3-j721s2-common-proc-board.dtb
+
 dtb-$(CONFIG_ARCH_K3) += k3-am642-evm.dtb
 dtb-$(CONFIG_ARCH_K3) += k3-am642-sk.dtb
+
+dtb-$(CONFIG_ARCH_K3) += k3-am625-sk.dtb
+
+dtb-$(CONFIG_ARCH_K3) += k3-am62a7-sk.dtb
diff --git a/arch/arm64/boot/dts/ti/k3-am62-main.dtsi b/arch/arm64/boot/dts/ti/k3-am62-main.dtsi
new file mode 100644
index 000000000000..03660476364f
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-am62-main.dtsi
@@ -0,0 +1,620 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device Tree Source for AM625 SoC Family Main Domain peripherals
+ *
+ * Copyright (C) 2020-2022 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+&cbass_main {
+	oc_sram: sram@70000000 {
+		compatible = "mmio-sram";
+		reg = <0x00 0x70000000 0x00 0x10000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x00 0x70000000 0x10000>;
+	};
+
+	gic500: interrupt-controller@1800000 {
+		compatible = "arm,gic-v3";
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+		#interrupt-cells = <3>;
+		interrupt-controller;
+		reg = <0x00 0x01800000 0x00 0x10000>,	/* GICD */
+		      <0x00 0x01880000 0x00 0xc0000>,	/* GICR */
+		      <0x00 0x01880000 0x00 0xc0000>,   /* GICR */
+		      <0x01 0x00000000 0x00 0x2000>,    /* GICC */
+		      <0x01 0x00010000 0x00 0x1000>,    /* GICH */
+		      <0x01 0x00020000 0x00 0x2000>;    /* GICV */
+		/*
+		 * vcpumntirq:
+		 * virtual CPU interface maintenance interrupt
+		 */
+		interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
+
+		gic_its: msi-controller@1820000 {
+			compatible = "arm,gic-v3-its";
+			reg = <0x00 0x01820000 0x00 0x10000>;
+			socionext,synquacer-pre-its = <0x1000000 0x400000>;
+			msi-controller;
+			#msi-cells = <1>;
+		};
+	};
+
+	main_conf: syscon@100000 {
+		compatible = "syscon", "simple-mfd";
+		reg = <0x00 0x00100000 0x00 0x20000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x00 0x00100000 0x20000>;
+
+		phy_gmii_sel: phy@4044 {
+			compatible = "ti,am654-phy-gmii-sel";
+			reg = <0x4044 0x8>;
+			#phy-cells = <1>;
+		};
+
+		epwm_tbclk: clock@4130 {
+			compatible = "ti,am62-epwm-tbclk", "syscon";
+			reg = <0x4130 0x4>;
+			#clock-cells = <1>;
+		};
+	};
+
+	dmss: bus@48000000 {
+		compatible = "simple-mfd";
+		#address-cells = <2>;
+		#size-cells = <2>;
+		dma-ranges;
+		ranges = <0x00 0x48000000 0x00 0x48000000 0x00 0x06400000>;
+
+		ti,sci-dev-id = <25>;
+
+		secure_proxy_main: mailbox@4d000000 {
+			compatible = "ti,am654-secure-proxy";
+			#mbox-cells = <1>;
+			reg-names = "target_data", "rt", "scfg";
+			reg = <0x00 0x4d000000 0x00 0x80000>,
+			      <0x00 0x4a600000 0x00 0x80000>,
+			      <0x00 0x4a400000 0x00 0x80000>;
+			interrupt-names = "rx_012";
+			interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		inta_main_dmss: interrupt-controller@48000000 {
+			compatible = "ti,sci-inta";
+			reg = <0x00 0x48000000 0x00 0x100000>;
+			#interrupt-cells = <0>;
+			interrupt-controller;
+			interrupt-parent = <&gic500>;
+			msi-controller;
+			ti,sci = <&dmsc>;
+			ti,sci-dev-id = <28>;
+			ti,interrupt-ranges = <4 68 36>;
+			ti,unmapped-event-sources = <&main_bcdma>, <&main_pktdma>;
+		};
+
+		main_bcdma: dma-controller@485c0100 {
+			compatible = "ti,am64-dmss-bcdma";
+			reg = <0x00 0x485c0100 0x00 0x100>,
+			      <0x00 0x4c000000 0x00 0x20000>,
+			      <0x00 0x4a820000 0x00 0x20000>,
+			      <0x00 0x4aa40000 0x00 0x20000>,
+			      <0x00 0x4bc00000 0x00 0x100000>;
+			reg-names = "gcfg", "bchanrt", "rchanrt", "tchanrt", "ringrt";
+			msi-parent = <&inta_main_dmss>;
+			#dma-cells = <3>;
+
+			ti,sci = <&dmsc>;
+			ti,sci-dev-id = <26>;
+			ti,sci-rm-range-bchan = <0x20>; /* BLOCK_COPY_CHAN */
+			ti,sci-rm-range-rchan = <0x21>; /* SPLIT_TR_RX_CHAN */
+			ti,sci-rm-range-tchan = <0x22>; /* SPLIT_TR_TX_CHAN */
+		};
+
+		main_pktdma: dma-controller@485c0000 {
+			compatible = "ti,am64-dmss-pktdma";
+			reg = <0x00 0x485c0000 0x00 0x100>,
+			      <0x00 0x4a800000 0x00 0x20000>,
+			      <0x00 0x4aa00000 0x00 0x40000>,
+			      <0x00 0x4b800000 0x00 0x400000>;
+			reg-names = "gcfg", "rchanrt", "tchanrt", "ringrt";
+			msi-parent = <&inta_main_dmss>;
+			#dma-cells = <2>;
+
+			ti,sci = <&dmsc>;
+			ti,sci-dev-id = <30>;
+			ti,sci-rm-range-tchan = <0x23>, /* UNMAPPED_TX_CHAN */
+						<0x24>, /* CPSW_TX_CHAN */
+						<0x25>, /* SAUL_TX_0_CHAN */
+						<0x26>; /* SAUL_TX_1_CHAN */
+			ti,sci-rm-range-tflow = <0x10>, /* RING_UNMAPPED_TX_CHAN */
+						<0x11>, /* RING_CPSW_TX_CHAN */
+						<0x12>, /* RING_SAUL_TX_0_CHAN */
+						<0x13>; /* RING_SAUL_TX_1_CHAN */
+			ti,sci-rm-range-rchan = <0x29>, /* UNMAPPED_RX_CHAN */
+						<0x2b>, /* CPSW_RX_CHAN */
+						<0x2d>, /* SAUL_RX_0_CHAN */
+						<0x2f>, /* SAUL_RX_1_CHAN */
+						<0x31>, /* SAUL_RX_2_CHAN */
+						<0x33>; /* SAUL_RX_3_CHAN */
+			ti,sci-rm-range-rflow = <0x2a>, /* FLOW_UNMAPPED_RX_CHAN */
+						<0x2c>, /* FLOW_CPSW_RX_CHAN */
+						<0x2e>, /* FLOW_SAUL_RX_0/1_CHAN */
+						<0x32>; /* FLOW_SAUL_RX_2/3_CHAN */
+		};
+	};
+
+	dmsc: system-controller@44043000 {
+		compatible = "ti,k2g-sci";
+		ti,host-id = <12>;
+		mbox-names = "rx", "tx";
+		mboxes = <&secure_proxy_main 12>,
+			 <&secure_proxy_main 13>;
+		reg-names = "debug_messages";
+		reg = <0x00 0x44043000 0x00 0xfe0>;
+
+		k3_pds: power-controller {
+			compatible = "ti,sci-pm-domain";
+			#power-domain-cells = <2>;
+		};
+
+		k3_clks: clock-controller {
+			compatible = "ti,k2g-sci-clk";
+			#clock-cells = <2>;
+		};
+
+		k3_reset: reset-controller {
+			compatible = "ti,sci-reset";
+			#reset-cells = <2>;
+		};
+	};
+
+	crypto: crypto@40900000 {
+		compatible = "ti,am62-sa3ul";
+		reg = <0x00 0x40900000 0x00 0x1200>;
+		power-domains = <&k3_pds 70 TI_SCI_PD_SHARED>;
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges = <0x00 0x40900000 0x00 0x40900000 0x00 0x30000>;
+
+		dmas = <&main_pktdma 0xf501 0>, <&main_pktdma 0x7506 0>,
+		       <&main_pktdma 0x7507 0>;
+		dma-names = "tx", "rx1", "rx2";
+	};
+
+	main_pmx0: pinctrl@f4000 {
+		compatible = "pinctrl-single";
+		reg = <0x00 0xf4000 0x00 0x2ac>;
+		#pinctrl-cells = <1>;
+		pinctrl-single,register-width = <32>;
+		pinctrl-single,function-mask = <0xffffffff>;
+	};
+
+	main_uart0: serial@2800000 {
+		compatible = "ti,am64-uart", "ti,am654-uart";
+		reg = <0x00 0x02800000 0x00 0x100>;
+		interrupts = <GIC_SPI 178 IRQ_TYPE_LEVEL_HIGH>;
+		power-domains = <&k3_pds 146 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 146 0>;
+		clock-names = "fclk";
+	};
+
+	main_uart1: serial@2810000 {
+		compatible = "ti,am64-uart", "ti,am654-uart";
+		reg = <0x00 0x02810000 0x00 0x100>;
+		interrupts = <GIC_SPI 179 IRQ_TYPE_LEVEL_HIGH>;
+		power-domains = <&k3_pds 152 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 152 0>;
+		clock-names = "fclk";
+	};
+
+	main_uart2: serial@2820000 {
+		compatible = "ti,am64-uart", "ti,am654-uart";
+		reg = <0x00 0x02820000 0x00 0x100>;
+		interrupts = <GIC_SPI 180 IRQ_TYPE_LEVEL_HIGH>;
+		power-domains = <&k3_pds 153 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 153 0>;
+		clock-names = "fclk";
+	};
+
+	main_uart3: serial@2830000 {
+		compatible = "ti,am64-uart", "ti,am654-uart";
+		reg = <0x00 0x02830000 0x00 0x100>;
+		interrupts = <GIC_SPI 181 IRQ_TYPE_LEVEL_HIGH>;
+		power-domains = <&k3_pds 154 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 154 0>;
+		clock-names = "fclk";
+	};
+
+	main_uart4: serial@2840000 {
+		compatible = "ti,am64-uart", "ti,am654-uart";
+		reg = <0x00 0x02840000 0x00 0x100>;
+		interrupts = <GIC_SPI 182 IRQ_TYPE_LEVEL_HIGH>;
+		power-domains = <&k3_pds 155 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 155 0>;
+		clock-names = "fclk";
+	};
+
+	main_uart5: serial@2850000 {
+		compatible = "ti,am64-uart", "ti,am654-uart";
+		reg = <0x00 0x02850000 0x00 0x100>;
+		interrupts = <GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>;
+		power-domains = <&k3_pds 156 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 156 0>;
+		clock-names = "fclk";
+	};
+
+	main_uart6: serial@2860000 {
+		compatible = "ti,am64-uart", "ti,am654-uart";
+		reg = <0x00 0x02860000 0x00 0x100>;
+		interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>;
+		power-domains = <&k3_pds 158 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 158 0>;
+		clock-names = "fclk";
+	};
+
+	main_i2c0: i2c@20000000 {
+		compatible = "ti,am64-i2c", "ti,omap4-i2c";
+		reg = <0x00 0x20000000 0x00 0x100>;
+		interrupts = <GIC_SPI 161 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		power-domains = <&k3_pds 102 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 102 2>;
+		clock-names = "fck";
+	};
+
+	main_i2c1: i2c@20010000 {
+		compatible = "ti,am64-i2c", "ti,omap4-i2c";
+		reg = <0x00 0x20010000 0x00 0x100>;
+		interrupts = <GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		power-domains = <&k3_pds 103 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 103 2>;
+		clock-names = "fck";
+	};
+
+	main_i2c2: i2c@20020000 {
+		compatible = "ti,am64-i2c", "ti,omap4-i2c";
+		reg = <0x00 0x20020000 0x00 0x100>;
+		interrupts = <GIC_SPI 163 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		power-domains = <&k3_pds 104 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 104 2>;
+		clock-names = "fck";
+	};
+
+	main_i2c3: i2c@20030000 {
+		compatible = "ti,am64-i2c", "ti,omap4-i2c";
+		reg = <0x00 0x20030000 0x00 0x100>;
+		interrupts = <GIC_SPI 164 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		power-domains = <&k3_pds 105 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 105 2>;
+		clock-names = "fck";
+	};
+
+	main_spi0: spi@20100000 {
+		compatible = "ti,am654-mcspi", "ti,omap4-mcspi";
+		reg = <0x00 0x20100000 0x00 0x400>;
+		interrupts = <GIC_SPI 172 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		power-domains = <&k3_pds 141 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 172 0>;
+	};
+
+	main_spi1: spi@20110000 {
+		compatible = "ti,am654-mcspi","ti,omap4-mcspi";
+		reg = <0x00 0x20110000 0x00 0x400>;
+		interrupts = <GIC_SPI 173 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		power-domains = <&k3_pds 142 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 173 0>;
+	};
+
+	main_spi2: spi@20120000 {
+		compatible = "ti,am654-mcspi","ti,omap4-mcspi";
+		reg = <0x00 0x20120000 0x00 0x400>;
+		interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		power-domains = <&k3_pds 143 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 174 0>;
+	};
+
+	main_gpio_intr: interrupt-controller@a00000 {
+		compatible = "ti,sci-intr";
+		reg = <0x00 0x00a00000 0x00 0x800>;
+		ti,intr-trigger-type = <1>;
+		interrupt-controller;
+		interrupt-parent = <&gic500>;
+		#interrupt-cells = <1>;
+		ti,sci = <&dmsc>;
+		ti,sci-dev-id = <3>;
+		ti,interrupt-ranges = <0 32 16>;
+	};
+
+	main_gpio0: gpio@600000 {
+		compatible = "ti,am64-gpio", "ti,keystone-gpio";
+		reg = <0x0 0x00600000 0x0 0x100>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-parent = <&main_gpio_intr>;
+		interrupts = <190>, <191>, <192>,
+			     <193>, <194>, <195>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		ti,ngpio = <87>;
+		ti,davinci-gpio-unbanked = <0>;
+		power-domains = <&k3_pds 77 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 77 0>;
+		clock-names = "gpio";
+	};
+
+	main_gpio1: gpio@601000 {
+		compatible = "ti,am64-gpio", "ti,keystone-gpio";
+		reg = <0x0 0x00601000 0x0 0x100>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-parent = <&main_gpio_intr>;
+		interrupts = <180>, <181>, <182>,
+			     <183>, <184>, <185>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		ti,ngpio = <88>;
+		ti,davinci-gpio-unbanked = <0>;
+		power-domains = <&k3_pds 78 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 78 0>;
+		clock-names = "gpio";
+	};
+
+	sdhci0: mmc@fa10000 {
+		compatible = "ti,am62-sdhci";
+		reg = <0x00 0x0fa10000 0x00 0x1000>, <0x00 0x0fa18000 0x00 0x400>;
+		interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
+		power-domains = <&k3_pds 57 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 57 5>, <&k3_clks 57 6>;
+		clock-names = "clk_ahb", "clk_xin";
+		assigned-clocks = <&k3_clks 57 6>;
+		assigned-clock-parents = <&k3_clks 57 8>;
+		mmc-ddr-1_8v;
+		mmc-hs200-1_8v;
+		ti,trm-icp = <0x2>;
+		bus-width = <8>;
+		ti,clkbuf-sel = <0x7>;
+		ti,otap-del-sel-legacy = <0x0>;
+		ti,otap-del-sel-mmc-hs = <0x0>;
+		ti,otap-del-sel-ddr52 = <0x9>;
+		ti,otap-del-sel-hs200 = <0x6>;
+	};
+
+	sdhci1: mmc@fa00000 {
+		compatible = "ti,am62-sdhci";
+		reg = <0x00 0x0fa00000 0x00 0x1000>, <0x00 0x0fa08000 0x00 0x400>;
+		interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
+		power-domains = <&k3_pds 58 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 58 5>, <&k3_clks 58 6>;
+		clock-names = "clk_ahb", "clk_xin";
+		ti,trm-icp = <0x2>;
+		ti,otap-del-sel-legacy = <0x0>;
+		ti,otap-del-sel-sd-hs = <0x0>;
+		ti,otap-del-sel-sdr12 = <0xf>;
+		ti,otap-del-sel-sdr25 = <0xf>;
+		ti,otap-del-sel-sdr50 = <0xc>;
+		ti,otap-del-sel-sdr104 = <0x6>;
+		ti,otap-del-sel-ddr50 = <0x9>;
+		ti,itap-del-sel-legacy = <0x0>;
+		ti,itap-del-sel-sd-hs = <0x0>;
+		ti,itap-del-sel-sdr12 = <0x0>;
+		ti,itap-del-sel-sdr25 = <0x0>;
+		ti,clkbuf-sel = <0x7>;
+		bus-width = <4>;
+	};
+
+	sdhci2: mmc@fa20000 {
+		compatible = "ti,am62-sdhci";
+		reg = <0x00 0x0fa20000 0x00 0x1000>, <0x00 0x0fa28000 0x00 0x400>;
+		interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
+		power-domains = <&k3_pds 184 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 184 5>, <&k3_clks 184 6>;
+		clock-names = "clk_ahb", "clk_xin";
+		ti,trm-icp = <0x2>;
+		ti,otap-del-sel-legacy = <0x0>;
+		ti,otap-del-sel-sd-hs = <0x0>;
+		ti,otap-del-sel-sdr12 = <0xf>;
+		ti,otap-del-sel-sdr25 = <0xf>;
+		ti,otap-del-sel-sdr50 = <0xc>;
+		ti,otap-del-sel-sdr104 = <0x6>;
+		ti,otap-del-sel-ddr50 = <0x9>;
+		ti,itap-del-sel-legacy = <0x0>;
+		ti,itap-del-sel-sd-hs = <0x0>;
+		ti,itap-del-sel-sdr12 = <0x0>;
+		ti,itap-del-sel-sdr25 = <0x0>;
+		ti,clkbuf-sel = <0x7>;
+	};
+
+	fss: bus@fc00000 {
+		compatible = "simple-bus";
+		reg = <0x00 0x0fc00000 0x00 0x70000>;
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		ospi0: spi@fc40000 {
+			compatible = "ti,am654-ospi", "cdns,qspi-nor";
+			reg = <0x00 0x0fc40000 0x00 0x100>,
+			      <0x05 0x00000000 0x01 0x00000000>;
+			interrupts = <GIC_SPI 139 IRQ_TYPE_LEVEL_HIGH>;
+			cdns,fifo-depth = <256>;
+			cdns,fifo-width = <4>;
+			cdns,trigger-address = <0x0>;
+			clocks = <&k3_clks 75 7>;
+			assigned-clocks = <&k3_clks 75 7>;
+			assigned-clock-parents = <&k3_clks 75 8>;
+			assigned-clock-rates = <166666666>;
+			power-domains = <&k3_pds 75 TI_SCI_PD_EXCLUSIVE>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+
+	cpsw3g: ethernet@8000000 {
+		compatible = "ti,am642-cpsw-nuss";
+		#address-cells = <2>;
+		#size-cells = <2>;
+		reg = <0x00 0x08000000 0x00 0x200000>;
+		reg-names = "cpsw_nuss";
+		ranges = <0x00 0x00 0x00 0x08000000 0x00 0x200000>;
+		clocks = <&k3_clks 13 0>;
+		assigned-clocks = <&k3_clks 13 3>;
+		assigned-clock-parents = <&k3_clks 13 11>;
+		clock-names = "fck";
+		power-domains = <&k3_pds 13 TI_SCI_PD_EXCLUSIVE>;
+
+		dmas = <&main_pktdma 0xc600 15>,
+		       <&main_pktdma 0xc601 15>,
+		       <&main_pktdma 0xc602 15>,
+		       <&main_pktdma 0xc603 15>,
+		       <&main_pktdma 0xc604 15>,
+		       <&main_pktdma 0xc605 15>,
+		       <&main_pktdma 0xc606 15>,
+		       <&main_pktdma 0xc607 15>,
+		       <&main_pktdma 0x4600 15>;
+		dma-names = "tx0", "tx1", "tx2", "tx3", "tx4", "tx5", "tx6",
+			    "tx7", "rx";
+
+		ethernet-ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cpsw_port1: port@1 {
+				reg = <1>;
+				ti,mac-only;
+				label = "port1";
+				phys = <&phy_gmii_sel 1>;
+				mac-address = [00 00 00 00 00 00];
+				ti,syscon-efuse = <&wkup_conf 0x200>;
+			};
+
+			cpsw_port2: port@2 {
+				reg = <2>;
+				ti,mac-only;
+				label = "port2";
+				phys = <&phy_gmii_sel 2>;
+				mac-address = [00 00 00 00 00 00];
+			};
+		};
+
+		cpsw3g_mdio: mdio@f00 {
+			compatible = "ti,cpsw-mdio","ti,davinci_mdio";
+			reg = <0x00 0xf00 0x00 0x100>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			clocks = <&k3_clks 13 0>;
+			clock-names = "fck";
+			bus_freq = <1000000>;
+		};
+
+		cpts@3d000 {
+			compatible = "ti,j721e-cpts";
+			reg = <0x00 0x3d000 0x00 0x400>;
+			clocks = <&k3_clks 13 3>;
+			clock-names = "cpts";
+			interrupts-extended = <&gic500 GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "cpts";
+			ti,cpts-ext-ts-inputs = <4>;
+			ti,cpts-periodic-outputs = <2>;
+		};
+	};
+
+	hwspinlock: spinlock@2a000000 {
+		compatible = "ti,am64-hwspinlock";
+		reg = <0x00 0x2a000000 0x00 0x1000>;
+		#hwlock-cells = <1>;
+	};
+
+	mailbox0_cluster0: mailbox@29000000 {
+		compatible = "ti,am64-mailbox";
+		reg = <0x00 0x29000000 0x00 0x200>;
+		interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
+		#mbox-cells = <1>;
+		ti,mbox-num-users = <4>;
+		ti,mbox-num-fifos = <16>;
+	};
+
+	ecap0: pwm@23100000 {
+		compatible = "ti,am3352-ecap";
+		#pwm-cells = <3>;
+		reg = <0x00 0x23100000 0x00 0x100>;
+		power-domains = <&k3_pds 51 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 51 0>;
+		clock-names = "fck";
+	};
+
+	ecap1: pwm@23110000 {
+		compatible = "ti,am3352-ecap";
+		#pwm-cells = <3>;
+		reg = <0x00 0x23110000 0x00 0x100>;
+		power-domains = <&k3_pds 52 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 52 0>;
+		clock-names = "fck";
+	};
+
+	ecap2: pwm@23120000 {
+		compatible = "ti,am3352-ecap";
+		#pwm-cells = <3>;
+		reg = <0x00 0x23120000 0x00 0x100>;
+		power-domains = <&k3_pds 53 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 53 0>;
+		clock-names = "fck";
+	};
+
+	main_mcan0: can@20701000 {
+		compatible = "bosch,m_can";
+		reg = <0x00 0x20701000 0x00 0x200>,
+		      <0x00 0x20708000 0x00 0x8000>;
+		reg-names = "m_can", "message_ram";
+		power-domains = <&k3_pds 98 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 98 6>, <&k3_clks 98 1>;
+		clock-names = "hclk", "cclk";
+		interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 156 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "int0", "int1";
+		bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
+	};
+
+	epwm0: pwm@23000000 {
+		compatible = "ti,am64-epwm", "ti,am3352-ehrpwm";
+		#pwm-cells = <3>;
+		reg = <0x00 0x23000000 0x00 0x100>;
+		power-domains = <&k3_pds 86 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&epwm_tbclk 0>, <&k3_clks 86 0>;
+		clock-names = "tbclk", "fck";
+	};
+
+	epwm1: pwm@23010000 {
+		compatible = "ti,am64-epwm", "ti,am3352-ehrpwm";
+		#pwm-cells = <3>;
+		reg = <0x00 0x23010000 0x00 0x100>;
+		power-domains = <&k3_pds 87 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&epwm_tbclk 1>, <&k3_clks 87 0>;
+		clock-names = "tbclk", "fck";
+	};
+
+	epwm2: pwm@23020000 {
+		compatible = "ti,am64-epwm", "ti,am3352-ehrpwm";
+		#pwm-cells = <3>;
+		reg = <0x00 0x23020000 0x00 0x100>;
+		power-domains = <&k3_pds 88 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&epwm_tbclk 2>, <&k3_clks 88 0>;
+		clock-names = "tbclk", "fck";
+	};
+};
diff --git a/arch/arm64/boot/dts/ti/k3-am62-mcu.dtsi b/arch/arm64/boot/dts/ti/k3-am62-mcu.dtsi
new file mode 100644
index 000000000000..f56c803560f2
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-am62-mcu.dtsi
@@ -0,0 +1,84 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device Tree Source for AM625 SoC Family MCU Domain peripherals
+ *
+ * Copyright (C) 2020-2022 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+&cbass_mcu {
+	mcu_pmx0: pinctrl@4084000 {
+		compatible = "pinctrl-single";
+		reg = <0x00 0x04084000 0x00 0x88>;
+		#pinctrl-cells = <1>;
+		pinctrl-single,register-width = <32>;
+		pinctrl-single,function-mask = <0xffffffff>;
+	};
+
+	mcu_uart0: serial@4a00000 {
+		compatible = "ti,am64-uart", "ti,am654-uart";
+		reg = <0x00 0x04a00000 0x00 0x100>;
+		interrupts = <GIC_SPI 185 IRQ_TYPE_LEVEL_HIGH>;
+		power-domains = <&k3_pds 149 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 149 0>;
+		clock-names = "fclk";
+	};
+
+	mcu_i2c0: i2c@4900000 {
+		compatible = "ti,am64-i2c", "ti,omap4-i2c";
+		reg = <0x00 0x04900000 0x00 0x100>;
+		interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		power-domains = <&k3_pds 106 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 106 2>;
+		clock-names = "fck";
+	};
+
+	mcu_spi0: spi@4b00000 {
+		compatible = "ti,am654-mcspi", "ti,omap4-mcspi";
+		reg = <0x00 0x04b00000 0x00 0x400>;
+		interrupts = <GIC_SPI 176 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		power-domains = <&k3_pds 147 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 147 0>;
+	};
+
+	mcu_spi1: spi@4b10000 {
+		compatible = "ti,am654-mcspi","ti,omap4-mcspi";
+		reg = <0x00 0x04b10000 0x00 0x400>;
+		interrupts = <GIC_SPI 177 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		power-domains = <&k3_pds 148 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 148 0>;
+	};
+
+	mcu_gpio_intr: interrupt-controller@4210000 {
+		compatible = "ti,sci-intr";
+		reg = <0x00 0x04210000 0x00 0x200>;
+		ti,intr-trigger-type = <1>;
+		interrupt-controller;
+		interrupt-parent = <&gic500>;
+		#interrupt-cells = <1>;
+		ti,sci = <&dmsc>;
+		ti,sci-dev-id = <5>;
+		ti,interrupt-ranges = <0 104 4>;
+	};
+
+	mcu_gpio0: gpio@4201000 {
+		compatible = "ti,am64-gpio", "ti,keystone-gpio";
+		reg = <0x00 0x4201000 0x00 0x100>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-parent = <&mcu_gpio_intr>;
+		interrupts = <30>, <31>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		ti,ngpio = <24>;
+		ti,davinci-gpio-unbanked = <0>;
+		power-domains = <&k3_pds 79 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 79 0>;
+		clock-names = "gpio";
+	};
+};
diff --git a/arch/arm64/boot/dts/ti/k3-am62-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-am62-wakeup.dtsi
new file mode 100644
index 000000000000..4090134676cf
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-am62-wakeup.dtsi
@@ -0,0 +1,41 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device Tree Source for AM625 SoC Family Wakeup Domain peripherals
+ *
+ * Copyright (C) 2020-2022 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+&cbass_wakeup {
+	wkup_conf: syscon@43000000 {
+		compatible = "syscon", "simple-mfd";
+		reg = <0x00 0x43000000 0x00 0x20000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x00 0x43000000 0x20000>;
+
+		chipid: chipid@14 {
+			compatible = "ti,am654-chipid";
+			reg = <0x14 0x4>;
+		};
+	};
+
+	wkup_uart0: serial@2b300000 {
+		compatible = "ti,am64-uart", "ti,am654-uart";
+		reg = <0x00 0x2b300000 0x00 0x100>;
+		interrupts = <GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>;
+		power-domains = <&k3_pds 114 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 114 0>;
+		clock-names = "fclk";
+	};
+
+	wkup_i2c0: i2c@2b200000 {
+		compatible = "ti,am64-i2c", "ti,omap4-i2c";
+		reg = <0x00 0x02b200000 0x00 0x100>;
+		interrupts = <GIC_SPI 165 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		power-domains = <&k3_pds 107 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 107 4>;
+		clock-names = "fck";
+	};
+};
diff --git a/arch/arm64/boot/dts/ti/k3-am62.dtsi b/arch/arm64/boot/dts/ti/k3-am62.dtsi
new file mode 100644
index 000000000000..37fcbe7a3c33
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-am62.dtsi
@@ -0,0 +1,106 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device Tree Source for AM62 SoC Family
+ *
+ * Copyright (C) 2020-2022 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/pinctrl/k3.h>
+#include <dt-bindings/soc/ti,sci_pm_domain.h>
+
+/ {
+	model = "Texas Instruments K3 AM625 SoC";
+	compatible = "ti,am625";
+	interrupt-parent = <&gic500>;
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	chosen { };
+
+	firmware {
+		optee {
+			compatible = "linaro,optee-tz";
+			method = "smc";
+		};
+
+		psci: psci {
+			compatible = "arm,psci-1.0";
+			method = "smc";
+		};
+	};
+
+	a53_timer0: timer-cl0-cpu0 {
+		compatible = "arm,armv8-timer";
+		interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW>, /* cntpsirq */
+			     <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW>, /* cntpnsirq */
+			     <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW>, /* cntvirq */
+			     <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW>; /* cnthpirq */
+	};
+
+	pmu: pmu {
+		compatible = "arm,cortex-a53-pmu";
+		interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
+	cbass_main: bus@f0000 {
+		compatible = "simple-bus";
+		#address-cells = <2>;
+		#size-cells = <2>;
+
+		ranges = <0x00 0x000f0000 0x00 0x000f0000 0x00 0x00030000>, /* Main MMRs */
+			 <0x00 0x00420000 0x00 0x00420000 0x00 0x00001000>, /* ESM0 */
+			 <0x00 0x00600000 0x00 0x00600000 0x00 0x00001100>, /* GPIO */
+			 <0x00 0x00703000 0x00 0x00703000 0x00 0x00000200>, /* USB0 debug trace */
+			 <0x00 0x0070c000 0x00 0x0070c000 0x00 0x00000200>, /* USB1 debug trace */
+			 <0x00 0x00a40000 0x00 0x00a40000 0x00 0x00000800>, /* Timesync router */
+			 <0x00 0x01000000 0x00 0x01000000 0x00 0x01b28400>, /* First peripheral window */
+			 <0x00 0x08000000 0x00 0x08000000 0x00 0x00200000>, /* Main CPSW */
+			 <0x00 0x0e000000 0x00 0x0e000000 0x00 0x01d20000>, /* Second peripheral window */
+			 <0x00 0x0fd00000 0x00 0x0fd00000 0x00 0x00020000>, /* GPU */
+			 <0x00 0x20000000 0x00 0x20000000 0x00 0x0a008000>, /* Third peripheral window */
+			 <0x00 0x30040000 0x00 0x30040000 0x00 0x00080000>, /* PRUSS-M */
+			 <0x00 0x30101000 0x00 0x30101000 0x00 0x00010100>, /* CSI window */
+			 <0x00 0x30200000 0x00 0x30200000 0x00 0x00010000>, /* DSS */
+			 <0x00 0x31000000 0x00 0x31000000 0x00 0x00050000>, /* USB0 DWC3 Core window */
+			 <0x00 0x31100000 0x00 0x31100000 0x00 0x00050000>, /* USB1 DWC3 Core window */
+			 <0x00 0x40900000 0x00 0x40900000 0x00 0x00030000>, /* SA3UL */
+			 <0x00 0x43600000 0x00 0x43600000 0x00 0x00010000>, /* SA3 sproxy data */
+			 <0x00 0x44043000 0x00 0x44043000 0x00 0x00000fe0>, /* TI SCI DEBUG */
+			 <0x00 0x44860000 0x00 0x44860000 0x00 0x00040000>, /* SA3 sproxy config */
+			 <0x00 0x48000000 0x00 0x48000000 0x00 0x06400000>, /* DMSS */
+			 <0x00 0x60000000 0x00 0x60000000 0x00 0x08000000>, /* FSS0 DAT1 */
+			 <0x00 0x70000000 0x00 0x70000000 0x00 0x00010000>, /* OCSRAM */
+			 <0x01 0x00000000 0x01 0x00000000 0x00 0x00310000>, /* A53 PERIPHBASE */
+			 <0x05 0x00000000 0x05 0x00000000 0x01 0x00000000>, /* FSS0 DAT3 */
+
+			 /* MCU Domain Range */
+			 <0x00 0x04000000 0x00 0x04000000 0x00 0x01ff1400>,
+
+			 /* Wakeup Domain Range */
+			 <0x00 0x2b000000 0x00 0x2b000000 0x00 0x00300400>,
+			 <0x00 0x43000000 0x00 0x43000000 0x00 0x00020000>;
+
+		cbass_mcu: bus@4000000 {
+			compatible = "simple-bus";
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges = <0x00 0x04000000 0x00 0x04000000 0x00 0x01ff1400>; /* Peripheral window */
+		};
+
+		cbass_wakeup: bus@2b000000 {
+			compatible = "simple-bus";
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges = <0x00 0x2b000000 0x00 0x2b000000 0x00 0x00300400>, /* Peripheral Window */
+				 <0x00 0x43000000 0x00 0x43000000 0x00 0x00020000>;
+		};
+	};
+};
+
+/* Now include the peripherals for each bus segments */
+#include "k3-am62-main.dtsi"
+#include "k3-am62-mcu.dtsi"
+#include "k3-am62-wakeup.dtsi"
diff --git a/arch/arm64/boot/dts/ti/k3-am625-sk.dts b/arch/arm64/boot/dts/ti/k3-am625-sk.dts
new file mode 100644
index 000000000000..93a5f0817efc
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-am625-sk.dts
@@ -0,0 +1,516 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * AM625 SK: https://www.ti.com/lit/zip/sprr448
+ *
+ * Copyright (C) 2021-2022 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/net/ti-dp83867.h>
+#include "k3-am625.dtsi"
+
+/ {
+	compatible = "ti,am625-sk", "ti,am625";
+	model = "Texas Instruments AM625 SK";
+
+	aliases {
+		serial2 = &main_uart0;
+		mmc0 = &sdhci0;
+		mmc1 = &sdhci1;
+		mmc2 = &sdhci2;
+		spi0 = &ospi0;
+		ethernet0 = &cpsw_port1;
+		ethernet1 = &cpsw_port2;
+	};
+
+	chosen {
+		stdout-path = "serial2:115200n8";
+		bootargs = "console=ttyS2,115200n8 earlycon=ns16550a,mmio32,0x02800000";
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		/* 2G RAM */
+		reg = <0x00000000 0x80000000 0x00000000 0x80000000>;
+
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		ramoops@9ca00000 {
+			compatible = "ramoops";
+			reg = <0x00 0x9ca00000 0x00 0x00100000>;
+			record-size = <0x8000>;
+			console-size = <0x8000>;
+			ftrace-size = <0x00>;
+			pmsg-size = <0x8000>;
+		};
+
+		secure_tfa_ddr: tfa@9e780000 {
+			reg = <0x00 0x9e780000 0x00 0x80000>;
+			alignment = <0x1000>;
+			no-map;
+		};
+
+		secure_ddr: optee@9e800000 {
+			reg = <0x00 0x9e800000 0x00 0x01800000>; /* for OP-TEE */
+			alignment = <0x1000>;
+			no-map;
+		};
+
+		wkup_r5fss0_core0_dma_memory_region: r5f-dma-memory@9db00000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0x9db00000 0x00 0xc00000>;
+			no-map;
+		};
+	};
+
+	vmain_pd: regulator-0 {
+		/* TPS65988 PD CONTROLLER OUTPUT */
+		compatible = "regulator-fixed";
+		regulator-name = "vmain_pd";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vcc_5v0: regulator-1 {
+		/* Output of LM34936 */
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_5v0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vmain_pd>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vcc_3v3_sys: regulator-2 {
+		/* output of LM61460-Q1 */
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_3v3_sys";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vmain_pd>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vdd_mmc1: regulator-3 {
+		/* TPS22918DBVR */
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_mmc1";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		enable-active-high;
+		vin-supply = <&vcc_3v3_sys>;
+		gpio = <&exp1 3 GPIO_ACTIVE_HIGH>;
+	};
+
+	vdd_sd_dv: regulator-4 {
+		/* Output of TLV71033 */
+		compatible = "regulator-gpio";
+		regulator-name = "tlv71033";
+		pinctrl-names = "default";
+		pinctrl-0 = <&vdd_sd_dv_pins_default>;
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		vin-supply = <&vcc_5v0>;
+		gpios = <&main_gpio0 31 GPIO_ACTIVE_HIGH>;
+		states = <1800000 0x0>,
+			 <3300000 0x1>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&usr_led_pins_default>;
+
+		led-0 {
+			label = "am62-sk:green:heartbeat";
+			gpios = <&main_gpio1 49 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+			function = LED_FUNCTION_HEARTBEAT;
+			default-state = "off";
+		};
+	};
+};
+
+&main_pmx0 {
+	main_uart0_pins_default: main-uart0-pins-default {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x1c8, PIN_INPUT, 0) /* (D14) UART0_RXD */
+			AM62X_IOPAD(0x1cc, PIN_OUTPUT, 0) /* (E14) UART0_TXD */
+		>;
+	};
+
+	main_i2c0_pins_default: main-i2c0-pins-default {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x1e0, PIN_INPUT_PULLUP, 0) /* (B16) I2C0_SCL */
+			AM62X_IOPAD(0x1e4, PIN_INPUT_PULLUP, 0) /* (A16) I2C0_SDA */
+		>;
+	};
+
+	main_i2c1_pins_default: main-i2c1-pins-default {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x1e8, PIN_INPUT_PULLUP, 0) /* (B17) I2C1_SCL */
+			AM62X_IOPAD(0x1ec, PIN_INPUT_PULLUP, 0) /* (A17) I2C1_SDA */
+		>;
+	};
+
+	main_i2c2_pins_default: main-i2c2-pins-default {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x0b0, PIN_INPUT_PULLUP, 1) /* (K22) GPMC0_CSn2.I2C2_SCL */
+			AM62X_IOPAD(0x0b4, PIN_INPUT_PULLUP, 1) /* (K24) GPMC0_CSn3.I2C2_SDA */
+		>;
+	};
+
+	main_mmc0_pins_default: main-mmc0-pins-default {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x220, PIN_INPUT, 0) /* (Y3) MMC0_CMD */
+			AM62X_IOPAD(0x218, PIN_INPUT, 0) /* (AB1) MMC0_CLK */
+			AM62X_IOPAD(0x214, PIN_INPUT, 0) /* (AA2) MMC0_DAT0 */
+			AM62X_IOPAD(0x210, PIN_INPUT, 0) /* (AA1) MMC0_DAT1 */
+			AM62X_IOPAD(0x20c, PIN_INPUT, 0) /* (AA3) MMC0_DAT2 */
+			AM62X_IOPAD(0x208, PIN_INPUT, 0) /* (Y4) MMC0_DAT3 */
+			AM62X_IOPAD(0x204, PIN_INPUT, 0) /* (AB2) MMC0_DAT4 */
+			AM62X_IOPAD(0x200, PIN_INPUT, 0) /* (AC1) MMC0_DAT5 */
+			AM62X_IOPAD(0x1fc, PIN_INPUT, 0) /* (AD2) MMC0_DAT6 */
+			AM62X_IOPAD(0x1f8, PIN_INPUT, 0) /* (AC2) MMC0_DAT7 */
+		>;
+	};
+
+	main_mmc1_pins_default: main-mmc1-pins-default {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x23c, PIN_INPUT, 0) /* (A21) MMC1_CMD */
+			AM62X_IOPAD(0x234, PIN_INPUT, 0) /* (B22) MMC1_CLK */
+			AM62X_IOPAD(0x230, PIN_INPUT, 0) /* (A22) MMC1_DAT0 */
+			AM62X_IOPAD(0x22c, PIN_INPUT, 0) /* (B21) MMC1_DAT1 */
+			AM62X_IOPAD(0x228, PIN_INPUT, 0) /* (C21) MMC1_DAT2 */
+			AM62X_IOPAD(0x224, PIN_INPUT, 0) /* (D22) MMC1_DAT3 */
+			AM62X_IOPAD(0x240, PIN_INPUT, 0) /* (D17) MMC1_SDCD */
+		>;
+	};
+
+	usr_led_pins_default: usr-led-pins-default {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x244, PIN_OUTPUT, 7) /* (C17) MMC1_SDWP.GPIO1_49 */
+		>;
+	};
+
+	main_mdio1_pins_default: main-mdio1-pins-default {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x160, PIN_OUTPUT, 0) /* (AD24) MDIO0_MDC */
+			AM62X_IOPAD(0x15c, PIN_INPUT, 0) /* (AB22) MDIO0_MDIO */
+		>;
+	};
+
+	main_rgmii1_pins_default: main-rgmii1-pins-default {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x14c, PIN_INPUT, 0) /* (AB17) RGMII1_RD0 */
+			AM62X_IOPAD(0x150, PIN_INPUT, 0) /* (AC17) RGMII1_RD1 */
+			AM62X_IOPAD(0x154, PIN_INPUT, 0) /* (AB16) RGMII1_RD2 */
+			AM62X_IOPAD(0x158, PIN_INPUT, 0) /* (AA15) RGMII1_RD3 */
+			AM62X_IOPAD(0x148, PIN_INPUT, 0) /* (AD17) RGMII1_RXC */
+			AM62X_IOPAD(0x144, PIN_INPUT, 0) /* (AE17) RGMII1_RX_CTL */
+			AM62X_IOPAD(0x134, PIN_OUTPUT, 0) /* (AE20) RGMII1_TD0 */
+			AM62X_IOPAD(0x138, PIN_OUTPUT, 0) /* (AD20) RGMII1_TD1 */
+			AM62X_IOPAD(0x13c, PIN_OUTPUT, 0) /* (AE18) RGMII1_TD2 */
+			AM62X_IOPAD(0x140, PIN_OUTPUT, 0) /* (AD18) RGMII1_TD3 */
+			AM62X_IOPAD(0x130, PIN_OUTPUT, 0) /* (AE19) RGMII1_TXC */
+			AM62X_IOPAD(0x12c, PIN_OUTPUT, 0) /* (AD19) RGMII1_TX_CTL */
+		>;
+	};
+
+	main_rgmii2_pins_default: main-rgmii2-pins-default {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x184, PIN_INPUT, 0) /* (AE23) RGMII2_RD0 */
+			AM62X_IOPAD(0x188, PIN_INPUT, 0) /* (AB20) RGMII2_RD1 */
+			AM62X_IOPAD(0x18c, PIN_INPUT, 0) /* (AC21) RGMII2_RD2 */
+			AM62X_IOPAD(0x190, PIN_INPUT, 0) /* (AE22) RGMII2_RD3 */
+			AM62X_IOPAD(0x180, PIN_INPUT, 0) /* (AD23) RGMII2_RXC */
+			AM62X_IOPAD(0x17c, PIN_INPUT, 0) /* (AD22) RGMII2_RX_CTL */
+			AM62X_IOPAD(0x16c, PIN_OUTPUT, 0) /* (Y18) RGMII2_TD0 */
+			AM62X_IOPAD(0x170, PIN_OUTPUT, 0) /* (AA18) RGMII2_TD1 */
+			AM62X_IOPAD(0x174, PIN_OUTPUT, 0) /* (AD21) RGMII2_TD2 */
+			AM62X_IOPAD(0x178, PIN_OUTPUT, 0) /* (AC20) RGMII2_TD3 */
+			AM62X_IOPAD(0x168, PIN_OUTPUT, 0) /* (AE21) RGMII2_TXC */
+			AM62X_IOPAD(0x164, PIN_OUTPUT, 0) /* (AA19) RGMII2_TX_CTL */
+		>;
+	};
+
+	ospi0_pins_default: ospi0-pins-default {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x000, PIN_OUTPUT, 0) /* (H24) OSPI0_CLK */
+			AM62X_IOPAD(0x02c, PIN_OUTPUT, 0) /* (F23) OSPI0_CSn0 */
+			AM62X_IOPAD(0x00c, PIN_INPUT, 0) /* (E25) OSPI0_D0 */
+			AM62X_IOPAD(0x010, PIN_INPUT, 0) /* (G24) OSPI0_D1 */
+			AM62X_IOPAD(0x014, PIN_INPUT, 0) /* (F25) OSPI0_D2 */
+			AM62X_IOPAD(0x018, PIN_INPUT, 0) /* (F24) OSPI0_D3 */
+			AM62X_IOPAD(0x01c, PIN_INPUT, 0) /* (J23) OSPI0_D4 */
+			AM62X_IOPAD(0x020, PIN_INPUT, 0) /* (J25) OSPI0_D5 */
+			AM62X_IOPAD(0x024, PIN_INPUT, 0) /* (H25) OSPI0_D6 */
+			AM62X_IOPAD(0x028, PIN_INPUT, 0) /* (J22) OSPI0_D7 */
+			AM62X_IOPAD(0x008, PIN_INPUT, 0) /* (J24) OSPI0_DQS */
+		>;
+	};
+
+	vdd_sd_dv_pins_default: vdd-sd-dv-pins-default {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x07c, PIN_OUTPUT, 7) /* (P25) GPMC0_CLK.GPIO0_31 */
+		>;
+	};
+
+	main_gpio1_ioexp_intr_pins_default: main-gpio1-ioexp-intr-pins-default {
+		pinctrl-single,pins = <
+			AM62X_IOPAD(0x01d4, PIN_INPUT, 7) /* (B15) UART0_RTSn.GPIO1_23 */
+		>;
+	};
+};
+
+&wkup_uart0 {
+	/* WKUP UART0 is used by DM firmware */
+	status = "reserved";
+};
+
+&mcu_uart0 {
+	status = "disabled";
+};
+
+&main_uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_uart0_pins_default>;
+};
+
+&main_uart1 {
+	/* Main UART1 is used by TIFS firmware */
+	status = "reserved";
+};
+
+&main_uart2 {
+	status = "disabled";
+};
+
+&main_uart3 {
+	status = "disabled";
+};
+
+&main_uart4 {
+	status = "disabled";
+};
+
+&main_uart5 {
+	status = "disabled";
+};
+
+&main_uart6 {
+	status = "disabled";
+};
+
+&mcu_i2c0 {
+	status = "disabled";
+};
+
+&wkup_i2c0 {
+	status = "disabled";
+};
+
+&main_i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_i2c0_pins_default>;
+	clock-frequency = <400000>;
+};
+
+&main_i2c1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_i2c1_pins_default>;
+	clock-frequency = <400000>;
+
+	exp1: gpio@22 {
+		compatible = "ti,tca6424";
+		reg = <0x22>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names = "GPIO_CPSW2_RST", "GPIO_CPSW1_RST",
+				   "PRU_DETECT", "MMC1_SD_EN",
+				   "VPP_LDO_EN", "EXP_PS_3V3_En",
+				   "EXP_PS_5V0_En", "EXP_HAT_DETECT",
+				   "GPIO_AUD_RSTn", "GPIO_eMMC_RSTn",
+				   "UART1_FET_BUF_EN", "WL_LT_EN",
+				   "GPIO_HDMI_RSTn", "CSI_GPIO1",
+				   "CSI_GPIO2", "PRU_3V3_EN",
+				   "HDMI_INTn", "TEST_GPIO2",
+				   "MCASP1_FET_EN", "MCASP1_BUF_BT_EN",
+				   "MCASP1_FET_SEL", "UART1_FET_SEL",
+				   "TSINT#", "IO_EXP_TEST_LED";
+
+		interrupt-parent = <&main_gpio1>;
+		interrupts = <23 IRQ_TYPE_EDGE_FALLING>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&main_gpio1_ioexp_intr_pins_default>;
+	};
+};
+
+&main_i2c2 {
+	status = "disabled";
+};
+
+&main_i2c3 {
+	status = "disabled";
+};
+
+&sdhci0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_mmc0_pins_default>;
+	ti,driver-strength-ohm = <50>;
+	disable-wp;
+};
+
+&sdhci1 {
+	/* SD/MMC */
+	vmmc-supply = <&vdd_mmc1>;
+	vqmmc-supply = <&vdd_sd_dv>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_mmc1_pins_default>;
+	ti,driver-strength-ohm = <50>;
+	disable-wp;
+};
+
+&cpsw3g {
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_mdio1_pins_default
+		     &main_rgmii1_pins_default
+		     &main_rgmii2_pins_default>;
+};
+
+&cpsw_port1 {
+	phy-mode = "rgmii-rxid";
+	phy-handle = <&cpsw3g_phy0>;
+};
+
+&cpsw_port2 {
+	phy-mode = "rgmii-rxid";
+	phy-handle = <&cpsw3g_phy1>;
+};
+
+&cpsw3g_mdio {
+	cpsw3g_phy0: ethernet-phy@0 {
+		reg = <0>;
+		ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+		ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+		ti,min-output-impedance;
+	};
+
+	cpsw3g_phy1: ethernet-phy@1 {
+		reg = <1>;
+		ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+		ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+		ti,min-output-impedance;
+	};
+};
+
+&mailbox0_cluster0 {
+	mbox_m4_0: mbox-m4-0 {
+		ti,mbox-rx = <0 0 0>;
+		ti,mbox-tx = <1 0 0>;
+	};
+};
+
+&ospi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&ospi0_pins_default>;
+
+	flash@0{
+		compatible = "jedec,spi-nor";
+		reg = <0x0>;
+		spi-tx-bus-width = <8>;
+		spi-rx-bus-width = <8>;
+		spi-max-frequency = <25000000>;
+		cdns,tshsl-ns = <60>;
+		cdns,tsd2d-ns = <60>;
+		cdns,tchsh-ns = <60>;
+		cdns,tslch-ns = <60>;
+		cdns,read-delay = <4>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "ospi.tiboot3";
+				reg = <0x0 0x80000>;
+			};
+
+			partition@80000 {
+				label = "ospi.tispl";
+				reg = <0x80000 0x200000>;
+			};
+
+			partition@280000 {
+				label = "ospi.u-boot";
+				reg = <0x280000 0x400000>;
+			};
+
+			partition@680000 {
+				label = "ospi.env";
+				reg = <0x680000 0x40000>;
+			};
+
+			partition@6c0000 {
+				label = "ospi.env.backup";
+				reg = <0x6c0000 0x40000>;
+			};
+
+			partition@800000 {
+				label = "ospi.rootfs";
+				reg = <0x800000 0x37c0000>;
+			};
+
+			partition@3fc0000 {
+				label = "ospi.phypattern";
+				reg = <0x3fc0000 0x40000>;
+			};
+		};
+	};
+};
+
+&ecap0 {
+	status = "disabled";
+};
+
+&ecap1 {
+	status = "disabled";
+};
+
+&ecap2 {
+	status = "disabled";
+};
+
+&main_mcan0 {
+	status = "disabled";
+};
+
+&epwm0 {
+	status = "disabled";
+};
+
+&epwm1 {
+	status = "disabled";
+};
+
+&epwm2 {
+	status = "disabled";
+};
diff --git a/arch/arm64/boot/dts/ti/k3-am625.dtsi b/arch/arm64/boot/dts/ti/k3-am625.dtsi
new file mode 100644
index 000000000000..887f31c23fef
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-am625.dtsi
@@ -0,0 +1,103 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device Tree Source for AM625 SoC family in Quad core configuration
+ *
+ * TRM: https://www.ti.com/lit/pdf/spruiv7
+ *
+ * Copyright (C) 2020-2022 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+/dts-v1/;
+
+#include "k3-am62.dtsi"
+
+/ {
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu-map {
+			cluster0: cluster0 {
+				core0 {
+					cpu = <&cpu0>;
+				};
+
+				core1 {
+					cpu = <&cpu1>;
+				};
+
+				core2 {
+					cpu = <&cpu2>;
+				};
+
+				core3 {
+					cpu = <&cpu3>;
+				};
+			};
+		};
+
+		cpu0: cpu@0 {
+			compatible = "arm,cortex-a53";
+			reg = <0x000>;
+			device_type = "cpu";
+			enable-method = "psci";
+			i-cache-size = <0x8000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <128>;
+			next-level-cache = <&L2_0>;
+		};
+
+		cpu1: cpu@1 {
+			compatible = "arm,cortex-a53";
+			reg = <0x001>;
+			device_type = "cpu";
+			enable-method = "psci";
+			i-cache-size = <0x8000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <128>;
+			next-level-cache = <&L2_0>;
+		};
+
+		cpu2: cpu@2 {
+			compatible = "arm,cortex-a53";
+			reg = <0x002>;
+			device_type = "cpu";
+			enable-method = "psci";
+			i-cache-size = <0x8000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <128>;
+			next-level-cache = <&L2_0>;
+		};
+
+		cpu3: cpu@3 {
+			compatible = "arm,cortex-a53";
+			reg = <0x003>;
+			device_type = "cpu";
+			enable-method = "psci";
+			i-cache-size = <0x8000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <128>;
+			next-level-cache = <&L2_0>;
+		};
+	};
+
+	L2_0: l2-cache0 {
+		compatible = "cache";
+		cache-level = <2>;
+		cache-size = <0x40000>;
+		cache-line-size = <64>;
+		cache-sets = <512>;
+	};
+};
diff --git a/arch/arm64/boot/dts/ti/k3-am62a-main.dtsi b/arch/arm64/boot/dts/ti/k3-am62a-main.dtsi
new file mode 100644
index 000000000000..bc4b50bcd177
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-am62a-main.dtsi
@@ -0,0 +1,298 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device Tree Source for AM62A SoC Family Main Domain peripherals
+ *
+ * Copyright (C) 2022 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+&cbass_main {
+	oc_sram: sram@70000000 {
+		compatible = "mmio-sram";
+		reg = <0x00 0x70000000 0x00 0x10000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x00 0x70000000 0x10000>;
+	};
+
+	gic500: interrupt-controller@1800000 {
+		compatible = "arm,gic-v3";
+		reg = <0x00 0x01800000 0x00 0x10000>,	/* GICD */
+		      <0x00 0x01880000 0x00 0xc0000>,	/* GICR */
+		      <0x00 0x01880000 0x00 0xc0000>,   /* GICR */
+		      <0x01 0x00000000 0x00 0x2000>,    /* GICC */
+		      <0x01 0x00010000 0x00 0x1000>,    /* GICH */
+		      <0x01 0x00020000 0x00 0x2000>;    /* GICV */
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+		#interrupt-cells = <3>;
+		interrupt-controller;
+		/*
+		 * vcpumntirq:
+		 * virtual CPU interface maintenance interrupt
+		 */
+		interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
+
+		gic_its: msi-controller@1820000 {
+			compatible = "arm,gic-v3-its";
+			reg = <0x00 0x01820000 0x00 0x10000>;
+			socionext,synquacer-pre-its = <0x1000000 0x400000>;
+			msi-controller;
+			#msi-cells = <1>;
+		};
+	};
+
+	main_conf: syscon@100000 {
+		compatible = "ti,j721e-system-controller", "syscon", "simple-mfd";
+		reg = <0x00 0x00100000 0x00 0x20000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x00 0x00 0x00100000 0x20000>;
+	};
+
+	dmss: bus@48000000 {
+		compatible = "simple-bus";
+		#address-cells = <2>;
+		#size-cells = <2>;
+		dma-ranges;
+		ranges = <0x00 0x48000000 0x00 0x48000000 0x00 0x06000000>;
+
+		ti,sci-dev-id = <25>;
+
+		secure_proxy_main: mailbox@4d000000 {
+			compatible = "ti,am654-secure-proxy";
+			reg = <0x00 0x4d000000 0x00 0x80000>,
+			      <0x00 0x4a600000 0x00 0x80000>,
+			      <0x00 0x4a400000 0x00 0x80000>;
+			reg-names = "target_data", "rt", "scfg";
+			#mbox-cells = <1>;
+			interrupt-names = "rx_012";
+			interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
+		};
+	};
+
+	dmsc: system-controller@44043000 {
+		compatible = "ti,k2g-sci";
+		reg = <0x00 0x44043000 0x00 0xfe0>;
+		reg-names = "debug_messages";
+		ti,host-id = <12>;
+		mbox-names = "rx", "tx";
+		mboxes= <&secure_proxy_main 12>,
+			<&secure_proxy_main 13>;
+
+		k3_pds: power-controller {
+			compatible = "ti,sci-pm-domain";
+			#power-domain-cells = <2>;
+		};
+
+		k3_clks: clock-controller {
+			compatible = "ti,k2g-sci-clk";
+			#clock-cells = <2>;
+		};
+
+		k3_reset: reset-controller {
+			compatible = "ti,sci-reset";
+			#reset-cells = <2>;
+		};
+	};
+
+	main_pmx0: pinctrl@f4000 {
+		compatible = "pinctrl-single";
+		reg = <0x00 0xf4000 0x00 0x2ac>;
+		#pinctrl-cells = <1>;
+		pinctrl-single,register-width = <32>;
+		pinctrl-single,function-mask = <0xffffffff>;
+	};
+
+	main_uart0: serial@2800000 {
+		compatible = "ti,am64-uart", "ti,am654-uart";
+		reg = <0x00 0x02800000 0x00 0x100>;
+		interrupts = <GIC_SPI 178 IRQ_TYPE_LEVEL_HIGH>;
+		power-domains = <&k3_pds 146 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 146 0>;
+		clock-names = "fclk";
+		status = "disabled";
+	};
+
+	main_uart1: serial@2810000 {
+		compatible = "ti,am64-uart", "ti,am654-uart";
+		reg = <0x00 0x02810000 0x00 0x100>;
+		interrupts = <GIC_SPI 179 IRQ_TYPE_LEVEL_HIGH>;
+		power-domains = <&k3_pds 152 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 152 0>;
+		clock-names = "fclk";
+		status = "disabled";
+	};
+
+	main_uart2: serial@2820000 {
+		compatible = "ti,am64-uart", "ti,am654-uart";
+		reg = <0x00 0x02820000 0x00 0x100>;
+		interrupts = <GIC_SPI 180 IRQ_TYPE_LEVEL_HIGH>;
+		power-domains = <&k3_pds 153 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 153 0>;
+		clock-names = "fclk";
+		status = "disabled";
+	};
+
+	main_uart3: serial@2830000 {
+		compatible = "ti,am64-uart", "ti,am654-uart";
+		reg = <0x00 0x02830000 0x00 0x100>;
+		interrupts = <GIC_SPI 181 IRQ_TYPE_LEVEL_HIGH>;
+		power-domains = <&k3_pds 154 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 154 0>;
+		clock-names = "fclk";
+		status = "disabled";
+	};
+
+	main_uart4: serial@2840000 {
+		compatible = "ti,am64-uart", "ti,am654-uart";
+		reg = <0x00 0x02840000 0x00 0x100>;
+		interrupts = <GIC_SPI 182 IRQ_TYPE_LEVEL_HIGH>;
+		power-domains = <&k3_pds 155 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 155 0>;
+		clock-names = "fclk";
+		status = "disabled";
+	};
+
+	main_uart5: serial@2850000 {
+		compatible = "ti,am64-uart", "ti,am654-uart";
+		reg = <0x00 0x02850000 0x00 0x100>;
+		interrupts = <GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>;
+		power-domains = <&k3_pds 156 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 156 0>;
+		clock-names = "fclk";
+		status = "disabled";
+	};
+
+	main_uart6: serial@2860000 {
+		compatible = "ti,am64-uart", "ti,am654-uart";
+		reg = <0x00 0x02860000 0x00 0x100>;
+		interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>;
+		power-domains = <&k3_pds 158 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 158 0>;
+		clock-names = "fclk";
+		status = "disabled";
+	};
+
+	main_i2c0: i2c@20000000 {
+		compatible = "ti,am64-i2c", "ti,omap4-i2c";
+		reg = <0x00 0x20000000 0x00 0x100>;
+		interrupts = <GIC_SPI 161 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		power-domains = <&k3_pds 102 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 102 2>;
+		clock-names = "fck";
+		status = "disabled";
+	};
+
+	main_i2c1: i2c@20010000 {
+		compatible = "ti,am64-i2c", "ti,omap4-i2c";
+		reg = <0x00 0x20010000 0x00 0x100>;
+		interrupts = <GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		power-domains = <&k3_pds 103 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 103 2>;
+		clock-names = "fck";
+		status = "disabled";
+	};
+
+	main_i2c2: i2c@20020000 {
+		compatible = "ti,am64-i2c", "ti,omap4-i2c";
+		reg = <0x00 0x20020000 0x00 0x100>;
+		interrupts = <GIC_SPI 163 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		power-domains = <&k3_pds 104 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 104 2>;
+		clock-names = "fck";
+		status = "disabled";
+	};
+
+	main_i2c3: i2c@20030000 {
+		compatible = "ti,am64-i2c", "ti,omap4-i2c";
+		reg = <0x00 0x20030000 0x00 0x100>;
+		interrupts = <GIC_SPI 164 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		power-domains = <&k3_pds 105 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 105 2>;
+		clock-names = "fck";
+		status = "disabled";
+	};
+
+	main_gpio_intr: interrupt-controller@a00000 {
+		compatible = "ti,sci-intr";
+		reg = <0x00 0x00a00000 0x00 0x800>;
+		ti,intr-trigger-type = <1>;
+		interrupt-controller;
+		interrupt-parent = <&gic500>;
+		#interrupt-cells = <1>;
+		ti,sci = <&dmsc>;
+		ti,sci-dev-id = <3>;
+		ti,interrupt-ranges = <0 32 16>;
+		status = "disabled";
+	};
+
+	main_gpio0: gpio@600000 {
+		compatible = "ti,am64-gpio", "ti,keystone-gpio";
+		reg = <0x00 0x00600000 0x0 0x100>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-parent = <&main_gpio_intr>;
+		interrupts = <190>, <191>, <192>,
+			     <193>, <194>, <195>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		ti,ngpio = <87>;
+		ti,davinci-gpio-unbanked = <0>;
+		power-domains = <&k3_pds 77 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 77 0>;
+		clock-names = "gpio";
+		status = "disabled";
+	};
+
+	main_gpio1: gpio@601000 {
+		compatible = "ti,am64-gpio", "ti,keystone-gpio";
+		reg = <0x00 0x00601000 0x0 0x100>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-parent = <&main_gpio_intr>;
+		interrupts = <180>, <181>, <182>,
+			     <183>, <184>, <185>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		ti,ngpio = <88>;
+		ti,davinci-gpio-unbanked = <0>;
+		power-domains = <&k3_pds 78 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 78 0>;
+		clock-names = "gpio";
+		status = "disabled";
+	};
+
+	sdhci1: mmc@fa00000 {
+		compatible = "ti,am62-sdhci";
+		reg = <0x00 0xfa00000 0x00 0x260>, <0x00 0xfa08000 0x00 0x134>;
+		interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
+		power-domains = <&k3_pds 58 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 58 5>, <&k3_clks 58 6>;
+		clock-names = "clk_ahb", "clk_xin";
+		ti,trm-icp = <0x2>;
+		ti,otap-del-sel-legacy = <0x0>;
+		ti,otap-del-sel-sd-hs = <0x0>;
+		ti,otap-del-sel-sdr12 = <0xf>;
+		ti,otap-del-sel-sdr25 = <0xf>;
+		ti,otap-del-sel-sdr50 = <0xc>;
+		ti,otap-del-sel-sdr104 = <0x6>;
+		ti,otap-del-sel-ddr50 = <0x9>;
+		ti,itap-del-sel-legacy = <0x0>;
+		ti,itap-del-sel-sd-hs = <0x0>;
+		ti,itap-del-sel-sdr12 = <0x0>;
+		ti,itap-del-sel-sdr25 = <0x0>;
+		ti,clkbuf-sel = <0x7>;
+		bus-width = <4>;
+		no-1-8-v;
+		status = "disabled";
+	};
+};
diff --git a/arch/arm64/boot/dts/ti/k3-am62a-mcu.dtsi b/arch/arm64/boot/dts/ti/k3-am62a-mcu.dtsi
new file mode 100644
index 000000000000..6d1e501b94ab
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-am62a-mcu.dtsi
@@ -0,0 +1,39 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device Tree Source for AM625 SoC Family MCU Domain peripherals
+ *
+ * Copyright (C) 2020-2022 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+&cbass_mcu {
+	mcu_pmx0: pinctrl@4084000 {
+		compatible = "pinctrl-single";
+		reg = <0x00 0x04084000 0x00 0x88>;
+		#pinctrl-cells = <1>;
+		pinctrl-single,register-width = <32>;
+		pinctrl-single,function-mask = <0xffffffff>;
+		status = "disabled";
+	};
+
+	mcu_uart0: serial@4a00000 {
+		compatible = "ti,am64-uart", "ti,am654-uart";
+		reg = <0x00 0x04a00000 0x00 0x100>;
+		interrupts = <GIC_SPI 185 IRQ_TYPE_LEVEL_HIGH>;
+		power-domains = <&k3_pds 149 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 149 0>;
+		clock-names = "fclk";
+		status = "disabled";
+	};
+
+	mcu_i2c0: i2c@4900000 {
+		compatible = "ti,am64-i2c", "ti,omap4-i2c";
+		reg = <0x00 0x04900000 0x00 0x100>;
+		interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		power-domains = <&k3_pds 106 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 106 2>;
+		clock-names = "fck";
+		status = "disabled";
+	};
+};
diff --git a/arch/arm64/boot/dts/ti/k3-am62a-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-am62a-wakeup.dtsi
new file mode 100644
index 000000000000..99afac40e8d4
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-am62a-wakeup.dtsi
@@ -0,0 +1,54 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device Tree Source for AM62A SoC Family Wakeup Domain peripherals
+ *
+ * Copyright (C) 2022 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+&cbass_wakeup {
+	wkup_conf: syscon@43000000 {
+		compatible = "ti,j721e-system-controller", "syscon", "simple-mfd";
+		reg = <0x00 0x43000000 0x00 0x20000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x00 0x00 0x43000000 0x20000>;
+
+		chipid: chipid@14 {
+			compatible = "ti,am654-chipid";
+			reg = <0x14 0x4>;
+		};
+	};
+
+	wkup_uart0: serial@2b300000 {
+		compatible = "ti,am64-uart", "ti,am654-uart";
+		reg = <0x00 0x2b300000 0x00 0x100>;
+		interrupts = <GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>;
+		power-domains = <&k3_pds 114 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 114 0>;
+		clock-names = "fclk";
+		status = "disabled";
+	};
+
+	wkup_i2c0: i2c@2b200000 {
+		compatible = "ti,am64-i2c", "ti,omap4-i2c";
+		reg = <0x00 0x02b200000 0x00 0x100>;
+		interrupts = <GIC_SPI 165 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		power-domains = <&k3_pds 107 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 107 4>;
+		clock-names = "fck";
+		status = "disabled";
+	};
+
+	wkup_rtc0: rtc@2b1f0000 {
+		compatible = "ti,am62-rtc";
+		reg = <0x00 0x2b1f0000 0x00 0x100>;
+		interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&k3_clks 117 6> , <&k3_clks 117 0>;
+		clock-names = "vbus", "osc32k";
+		power-domains = <&k3_pds 117 TI_SCI_PD_EXCLUSIVE>;
+		wakeup-source;
+		status = "disabled";
+	};
+};
diff --git a/arch/arm64/boot/dts/ti/k3-am62a.dtsi b/arch/arm64/boot/dts/ti/k3-am62a.dtsi
new file mode 100644
index 000000000000..6eb87c3f9f3c
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-am62a.dtsi
@@ -0,0 +1,122 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device Tree Source for AM62A SoC Family
+ *
+ * Copyright (C) 2022 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/pinctrl/k3.h>
+#include <dt-bindings/soc/ti,sci_pm_domain.h>
+
+/ {
+	model = "Texas Instruments K3 AM62A SoC";
+	compatible = "ti,am62a7";
+	interrupt-parent = <&gic500>;
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	chosen { };
+
+	firmware {
+		optee {
+			compatible = "linaro,optee-tz";
+			method = "smc";
+		};
+
+		psci: psci {
+			compatible = "arm,psci-1.0";
+			method = "smc";
+		};
+	};
+
+	a53_timer0: timer-cl0-cpu0 {
+		compatible = "arm,armv8-timer";
+		interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW>, /* cntpsirq */
+			     <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW>, /* cntpnsirq */
+			     <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW>, /* cntvirq */
+			     <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW>; /* cnthpirq */
+	};
+
+	pmu: pmu {
+		compatible = "arm,cortex-a53-pmu";
+		interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
+	cbass_main: bus@f0000 {
+		compatible = "simple-bus";
+		#address-cells = <2>;
+		#size-cells = <2>;
+
+		ranges = <0x00 0x000f0000 0x00 0x000f0000 0x00 0x00030000>, /* Main MMRs */
+			 <0x00 0x00420000 0x00 0x00420000 0x00 0x00001000>, /* ESM0 */
+			 <0x00 0x00600000 0x00 0x00600000 0x00 0x00001100>, /* GPIO */
+			 <0x00 0x00703000 0x00 0x00703000 0x00 0x00000200>, /* USB0 debug trace */
+			 <0x00 0x0070c000 0x00 0x0070c000 0x00 0x00000200>, /* USB1 debug trace */
+			 <0x00 0x00a40000 0x00 0x00a40000 0x00 0x00000800>, /* Timesync router */
+			 <0x00 0x01000000 0x00 0x01000000 0x00 0x01b28400>, /* First peripheral window */
+			 <0x00 0x08000000 0x00 0x08000000 0x00 0x00200000>, /* Main CPSW */
+			 <0x00 0x0e000000 0x00 0x0e000000 0x00 0x01d20000>, /* Second peripheral window */
+			 <0x00 0x0fd00000 0x00 0x0fd00000 0x00 0x00020000>, /* GPU */
+			 <0x00 0x20000000 0x00 0x20000000 0x00 0x0a008000>, /* Third peripheral window */
+			 <0x00 0x30040000 0x00 0x30040000 0x00 0x00080000>, /* PRUSS-M */
+			 <0x00 0x30101000 0x00 0x30101000 0x00 0x00010100>, /* CSI window */
+			 <0x00 0x30200000 0x00 0x30200000 0x00 0x00010000>, /* DSS */
+			 <0x00 0x30210000 0x00 0x30210000 0x00 0x00010000>, /* VPU */
+			 <0x00 0x31000000 0x00 0x31000000 0x00 0x00050000>, /* USB0 DWC3 Core window */
+			 <0x00 0x31100000 0x00 0x31100000 0x00 0x00050000>, /* USB1 DWC3 Core window */
+			 <0x00 0x40900000 0x00 0x40900000 0x00 0x00030000>, /* SA3UL */
+			 <0x00 0x43600000 0x00 0x43600000 0x00 0x00010000>, /* SA3 sproxy data */
+			 <0x00 0x44043000 0x00 0x44043000 0x00 0x00000fe0>, /* TI SCI DEBUG */
+			 <0x00 0x44860000 0x00 0x44860000 0x00 0x00040000>, /* SA3 sproxy config */
+			 <0x00 0x48000000 0x00 0x48000000 0x00 0x06400000>, /* DMSS */
+			 <0x00 0x60000000 0x00 0x60000000 0x00 0x08000000>, /* FSS0 DAT1 */
+			 <0x00 0x70000000 0x00 0x70000000 0x00 0x00010000>, /* OCSRAM */
+			 <0x00 0x7e000000 0x00 0x7e000000 0x00 0x00100000>, /* C7x_0 */
+			 <0x01 0x00000000 0x01 0x00000000 0x00 0x00310000>, /* A53 PERIPHBASE */
+			 <0x05 0x00000000 0x05 0x00000000 0x01 0x00000000>, /* FSS0 DAT3 */
+
+			 /* MCU Domain Range */
+			 <0x00 0x04000000 0x00 0x04000000 0x00 0x01ff1400>,
+			 <0x00 0x79000000 0x00 0x79000000 0x00 0x00008000>, /* MCU R5 ATCM */
+			 <0x00 0x79020000 0x00 0x79020000 0x00 0x00008000>, /* MCU R5 BTCM */
+			 <0x00 0x79100000 0x00 0x79100000 0x00 0x00040000>, /* MCU R5 IRAM0 */
+			 <0x00 0x79140000 0x00 0x79140000 0x00 0x00040000>, /* MCU R5 IRAM1 */
+
+			 /* Wakeup Domain Range */
+			 <0x00 0x00b00000 0x00 0x00b00000 0x00 0x00002400>,
+			 <0x00 0x2b000000 0x00 0x2b000000 0x00 0x00300400>,
+			 <0x00 0x43000000 0x00 0x43000000 0x00 0x00020000>,
+			 <0x00 0x78000000 0x00 0x78000000 0x00 0x00008000>, /* DM R5 ATCM */
+			 <0x00 0x78100000 0x00 0x78100000 0x00 0x00008000>; /* DM R5 BTCM */
+
+		cbass_mcu: bus@4000000 {
+			compatible = "simple-bus";
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges = <0x00 0x04000000 0x00 0x04000000 0x00 0x01ff1400>, /* Peripheral window */
+				 <0x00 0x79000000 0x00 0x79000000 0x00 0x00008000>, /* MCU R5 ATCM */
+				 <0x00 0x79020000 0x00 0x79020000 0x00 0x00008000>, /* MCU R5 BTCM */
+				 <0x00 0x79100000 0x00 0x79100000 0x00 0x00040000>, /* MCU IRAM0 */
+				 <0x00 0x79140000 0x00 0x79140000 0x00 0x00040000>; /* MCU IRAM1 */
+		};
+
+		cbass_wakeup: bus@b00000 {
+			compatible = "simple-bus";
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges = <0x00 0x00b00000 0x00 0x00b00000 0x00 0x00002400>, /* VTM */
+				 <0x00 0x2b000000 0x00 0x2b000000 0x00 0x00300400>, /* Peripheral Window */
+				 <0x00 0x43000000 0x00 0x43000000 0x00 0x00020000>, /* WKUP CTRL MMR */
+				 <0x00 0x78000000 0x00 0x78000000 0x00 0x00008000>, /* DM R5 ATCM*/
+				 <0x00 0x78100000 0x00 0x78100000 0x00 0x00008000>; /* DM R5 BTCM*/
+		};
+	};
+};
+
+/* Now include the peripherals for each bus segments */
+#include "k3-am62a-main.dtsi"
+#include "k3-am62a-mcu.dtsi"
+#include "k3-am62a-wakeup.dtsi"
diff --git a/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts b/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
new file mode 100644
index 000000000000..576dbce80ad8
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-am62a7-sk.dts
@@ -0,0 +1,223 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * AM62A SK: https://www.ti.com/lit/zip/sprr459
+ *
+ * Copyright (C) 2022 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/gpio/gpio.h>
+#include "k3-am62a7.dtsi"
+
+/ {
+	compatible =  "ti,am62a7-sk", "ti,am62a7";
+	model = "Texas Instruments AM62A7 SK";
+
+	aliases {
+		serial2 = &main_uart0;
+		mmc1 = &sdhci1;
+	};
+
+	chosen {
+		stdout-path = "serial2:115200n8";
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		/* 2G RAM */
+		reg = <0x00000000 0x80000000 0x00000000 0x80000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		secure_tfa_ddr: tfa@9e780000 {
+			reg = <0x00 0x9e780000 0x00 0x80000>;
+			alignment = <0x1000>;
+			no-map;
+		};
+
+		secure_ddr: optee@9e800000 {
+			reg = <0x00 0x9e800000 0x00 0x01800000>; /* for OP-TEE */
+			alignment = <0x1000>;
+			no-map;
+		};
+
+		wkup_r5fss0_core0_memory_region: r5f-dma-memory@9c900000 {
+			compatible = "shared-dma-pool";
+			reg = <0x00 0x9c900000 0x00 0x01e00000>;
+			no-map;
+		};
+	};
+
+	vmain_pd: regulator-0 {
+		/* TPS25750 PD CONTROLLER OUTPUT */
+		compatible = "regulator-fixed";
+		regulator-name = "vmain_pd";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vcc_5v0: regulator-1 {
+		/* Output of TPS63070 */
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_5v0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vmain_pd>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vcc_3v3_sys: regulator-2 {
+		/* output of LM5141-Q1 */
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_3v3_sys";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vmain_pd>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vdd_mmc1: regulator-3 {
+		/* TPS22918DBVR */
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_mmc1";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		enable-active-high;
+		gpio = <&exp1 3 GPIO_ACTIVE_HIGH>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&usr_led_pins_default>;
+
+		led-0 {
+			label = "am62a-sk:green:heartbeat";
+			gpios = <&main_gpio1 49 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+			function = LED_FUNCTION_HEARTBEAT;
+			default-state = "off";
+		};
+	};
+};
+
+&main_pmx0 {
+	main_uart0_pins_default: main-uart0-pins-default {
+		pinctrl-single,pins = <
+			AM62AX_IOPAD(0x1c8, PIN_INPUT, 0) /* (D14) UART0_RXD */
+			AM62AX_IOPAD(0x1cc, PIN_OUTPUT, 0) /* (E14) UART0_TXD */
+		>;
+	};
+
+	main_i2c0_pins_default: main-i2c0-pins-default {
+		pinctrl-single,pins = <
+			AM62AX_IOPAD(0x1e0, PIN_INPUT_PULLUP, 0) /* (B16) I2C0_SCL */
+			AM62AX_IOPAD(0x1e4, PIN_INPUT_PULLUP, 0) /* (A16) I2C0_SDA */
+		>;
+	};
+
+	main_i2c1_pins_default: main-i2c1-pins-default {
+		pinctrl-single,pins = <
+			AM62AX_IOPAD(0x1e8, PIN_INPUT_PULLUP, 0) /* (B17) I2C1_SCL */
+			AM62AX_IOPAD(0x1ec, PIN_INPUT_PULLUP, 0) /* (A17) I2C1_SDA */
+		>;
+	};
+
+	main_i2c2_pins_default: main-i2c2-pins-default {
+		pinctrl-single,pins = <
+			AM62AX_IOPAD(0x0b0, PIN_INPUT_PULLUP, 1) /* (K22) GPMC0_CSn2.I2C2_SCL */
+			AM62AX_IOPAD(0x0b4, PIN_INPUT_PULLUP, 1) /* (K24) GPMC0_CSn3.I2C2_SDA */
+		>;
+	};
+
+	main_mmc1_pins_default: main-mmc1-pins-default {
+		pinctrl-single,pins = <
+			AM62AX_IOPAD(0x23c, PIN_INPUT, 0) /* (A21) MMC1_CMD */
+			AM62AX_IOPAD(0x234, PIN_INPUT, 0) /* (B22) MMC1_CLK */
+			AM62AX_IOPAD(0x230, PIN_INPUT, 0) /* (A22) MMC1_DAT0 */
+			AM62AX_IOPAD(0x22c, PIN_INPUT, 0) /* (B21) MMC1_DAT1 */
+			AM62AX_IOPAD(0x228, PIN_INPUT, 0) /* (C21) MMC1_DAT2 */
+			AM62AX_IOPAD(0x224, PIN_INPUT, 0) /* (D22) MMC1_DAT3 */
+			AM62AX_IOPAD(0x240, PIN_INPUT, 0) /* (D17) MMC1_SDCD */
+		>;
+	};
+
+	usr_led_pins_default: usr-led-pins-default {
+		pinctrl-single,pins = <
+			AM62AX_IOPAD(0x244, PIN_OUTPUT, 7) /* (D18) MMC1_SDWP.GPIO1_49 */
+		>;
+	};
+};
+
+&main_i2c0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_i2c0_pins_default>;
+	clock-frequency = <400000>;
+};
+
+&main_i2c1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_i2c1_pins_default>;
+	clock-frequency = <400000>;
+
+	exp1: gpio@22 {
+		compatible = "ti,tca6424";
+		reg = <0x22>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		gpio-line-names = "GPIO_CPSW2_RST", "GPIO_CPSW1_RST",
+				   "BT_EN_SOC", "MMC1_SD_EN",
+				   "VPP_EN", "EXP_PS_3V3_En",
+				   "EXP_PS_5V0_En", "EXP_HAT_DETECT",
+				   "GPIO_AUD_RSTn", "GPIO_eMMC_RSTn",
+				   "UART1_FET_BUF_EN", "BT_UART_WAKE_SOC",
+				   "GPIO_HDMI_RSTn", "CSI_GPIO0",
+				   "CSI_GPIO1", "WLAN_ALERTn",
+				   "HDMI_INTn", "TEST_GPIO2",
+				   "MCASP1_FET_EN", "MCASP1_BUF_BT_EN",
+				   "MCASP1_FET_SEL", "UART1_FET_SEL",
+				   "PD_I2C_IRQ", "IO_EXP_TEST_LED";
+	};
+};
+
+&sdhci1 {
+	/* SD/MMC */
+	status = "okay";
+	vmmc-supply = <&vdd_mmc1>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_mmc1_pins_default>;
+	ti,driver-strength-ohm = <50>;
+	disable-wp;
+};
+
+&main_gpio0 {
+	status = "okay";
+};
+
+&main_gpio1 {
+	status = "okay";
+};
+
+&main_gpio_intr {
+	status = "okay";
+};
+
+&main_uart0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_uart0_pins_default>;
+};
diff --git a/arch/arm64/boot/dts/ti/k3-am62a7.dtsi b/arch/arm64/boot/dts/ti/k3-am62a7.dtsi
new file mode 100644
index 000000000000..331d89fda29d
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-am62a7.dtsi
@@ -0,0 +1,103 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device Tree Source for AM62A7 SoC family in Quad core configuration
+ *
+ * TRM: https://www.ti.com/lit/zip/spruj16
+ *
+ * Copyright (C) 2020-2022 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+/dts-v1/;
+
+#include "k3-am62a.dtsi"
+
+/ {
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu-map {
+			cluster0: cluster0 {
+				core0 {
+					cpu = <&cpu0>;
+				};
+
+				core1 {
+					cpu = <&cpu1>;
+				};
+
+				core2 {
+					cpu = <&cpu2>;
+				};
+
+				core3 {
+					cpu = <&cpu3>;
+				};
+			};
+		};
+
+		cpu0: cpu@0 {
+			compatible = "arm,cortex-a53";
+			reg = <0x000>;
+			device_type = "cpu";
+			enable-method = "psci";
+			i-cache-size = <0x8000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <128>;
+			next-level-cache = <&L2_0>;
+		};
+
+		cpu1: cpu@1 {
+			compatible = "arm,cortex-a53";
+			reg = <0x001>;
+			device_type = "cpu";
+			enable-method = "psci";
+			i-cache-size = <0x8000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <128>;
+			next-level-cache = <&L2_0>;
+		};
+
+		cpu2: cpu@2 {
+			compatible = "arm,cortex-a53";
+			reg = <0x002>;
+			device_type = "cpu";
+			enable-method = "psci";
+			i-cache-size = <0x8000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <128>;
+			next-level-cache = <&L2_0>;
+		};
+
+		cpu3: cpu@3 {
+			compatible = "arm,cortex-a53";
+			reg = <0x003>;
+			device_type = "cpu";
+			enable-method = "psci";
+			i-cache-size = <0x8000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <128>;
+			next-level-cache = <&L2_0>;
+		};
+	};
+
+	L2_0: l2-cache0 {
+		compatible = "cache";
+		cache-level = <2>;
+		cache-size = <0x40000>;
+		cache-line-size = <64>;
+		cache-sets = <512>;
+	};
+};
diff --git a/arch/arm64/boot/dts/ti/k3-am64-main.dtsi b/arch/arm64/boot/dts/ti/k3-am64-main.dtsi
index 5ad638b95ffc..d6aa23681bbe 100644
--- a/arch/arm64/boot/dts/ti/k3-am64-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am64-main.dtsi
@@ -59,7 +59,10 @@
 		#interrupt-cells = <3>;
 		interrupt-controller;
 		reg = <0x00 0x01800000 0x00 0x10000>,	/* GICD */
-		      <0x00 0x01840000 0x00 0xC0000>;	/* GICR */
+		      <0x00 0x01840000 0x00 0xC0000>,	/* GICR */
+		      <0x01 0x00000000 0x00 0x2000>,	/* GICC */
+		      <0x01 0x00010000 0x00 0x1000>,	/* GICH */
+		      <0x01 0x00020000 0x00 0x2000>;	/* GICV */
 		/*
 		 * vcpumntirq:
 		 * virtual CPU interface maintenance interrupt
@@ -171,7 +174,7 @@
 		compatible = "ti,k2g-sci";
 		ti,host-id = <12>;
 		mbox-names = "rx", "tx";
-		mboxes= <&secure_proxy_main 12>,
+		mboxes = <&secure_proxy_main 12>,
 			<&secure_proxy_main 13>;
 		reg-names = "debug_messages";
 		reg = <0x00 0x44043000 0x00 0xfe0>;
@@ -453,13 +456,11 @@
 		clock-names = "clk_ahb", "clk_xin";
 		mmc-ddr-1_8v;
 		mmc-hs200-1_8v;
-		mmc-hs400-1_8v;
 		ti,trm-icp = <0x2>;
 		ti,otap-del-sel-legacy = <0x0>;
 		ti,otap-del-sel-mmc-hs = <0x0>;
 		ti,otap-del-sel-ddr52 = <0x6>;
 		ti,otap-del-sel-hs200 = <0x7>;
-		ti,otap-del-sel-hs400 = <0x4>;
 	};
 
 	sdhci1: mmc@fa00000 {
@@ -549,7 +550,7 @@
 		};
 	};
 
-	cpts@39000000 {
+	main_cpts0: cpts@39000000 {
 		compatible = "ti,j721e-cpts";
 		reg = <0x0 0x39000000 0x0 0x400>;
 		reg-names = "cpts";
@@ -564,6 +565,14 @@
 		ti,cpts-ext-ts-inputs = <8>;
 	};
 
+	timesync_router: pinctrl@a40000 {
+		compatible = "pinctrl-single";
+		reg = <0x0 0xa40000 0x0 0x800>;
+		#pinctrl-cells = <1>;
+		pinctrl-single,register-width = <32>;
+		pinctrl-single,function-mask = <0x000107ff>;
+	};
+
 	usbss0: cdns-usb@f900000{
 		compatible = "ti,am64-usb";
 		reg = <0x00 0xf900000 0x00 0x100>;
@@ -974,6 +983,24 @@
 		clock-names = "fck";
 	};
 
+	main_rti0: watchdog@e000000 {
+			compatible = "ti,j7-rti-wdt";
+			reg = <0x00 0xe000000 0x00 0x100>;
+			clocks = <&k3_clks 125 0>;
+			power-domains = <&k3_pds 125 TI_SCI_PD_EXCLUSIVE>;
+			assigned-clocks = <&k3_clks 125 0>;
+			assigned-clock-parents = <&k3_clks 125 2>;
+	};
+
+	main_rti1: watchdog@e010000 {
+			compatible = "ti,j7-rti-wdt";
+			reg = <0x00 0xe010000 0x00 0x100>;
+			clocks = <&k3_clks 126 0>;
+			power-domains = <&k3_pds 126 TI_SCI_PD_EXCLUSIVE>;
+			assigned-clocks = <&k3_clks 126 0>;
+			assigned-clock-parents = <&k3_clks 126 2>;
+	};
+
 	icssg0: icssg@30000000 {
 		compatible = "ti,am642-icssg";
 		reg = <0x00 0x30000000 0x00 0x80000>;
@@ -1253,4 +1280,80 @@
 			bus_freq = <1000000>;
 		};
 	};
+
+	main_mcan0: can@20701000 {
+		compatible = "bosch,m_can";
+		reg = <0x00 0x20701000 0x00 0x200>,
+		      <0x00 0x20708000 0x00 0x8000>;
+		reg-names = "m_can", "message_ram";
+		power-domains = <&k3_pds 98 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 98 5>, <&k3_clks 98 0>;
+		clock-names = "hclk", "cclk";
+		interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 156 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "int0", "int1";
+		bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
+	};
+
+	main_mcan1: can@20711000 {
+		compatible = "bosch,m_can";
+		reg = <0x00 0x20711000 0x00 0x200>,
+		      <0x00 0x20718000 0x00 0x8000>;
+		reg-names = "m_can", "message_ram";
+		power-domains = <&k3_pds 99 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 99 5>, <&k3_clks 99 0>;
+		clock-names = "hclk", "cclk";
+		interrupts = <GIC_SPI 158 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 159 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "int0", "int1";
+		bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
+	};
+
+	crypto: crypto@40900000 {
+		compatible = "ti,am64-sa2ul";
+		reg = <0x00 0x40900000 0x00 0x1200>;
+		power-domains = <&k3_pds 133 TI_SCI_PD_SHARED>;
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges = <0x00 0x40900000 0x00 0x40900000 0x00 0x30000>;
+		dmas = <&main_pktdma 0xc001 0>, <&main_pktdma 0x4002 0>,
+		       <&main_pktdma 0x4003 0>;
+		dma-names = "tx", "rx1", "rx2";
+
+		rng: rng@40910000 {
+			compatible = "inside-secure,safexcel-eip76";
+			reg = <0x00 0x40910000 0x00 0x7d>;
+			interrupts = <GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&k3_clks 133 1>;
+			status = "disabled"; /* Used by OP-TEE */
+		};
+	};
+
+	gpmc0: memory-controller@3b000000 {
+		compatible = "ti,am64-gpmc";
+		power-domains = <&k3_pds 80 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 80 0>;
+		clock-names = "fck";
+		reg = <0x00 0x03b000000 0x00 0x400>,
+		      <0x00 0x050000000 0x00 0x8000000>;
+		reg-names = "cfg", "data";
+		interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>;
+		gpmc,num-cs = <3>;
+		gpmc,num-waitpins = <2>;
+		#address-cells = <2>;
+		#size-cells = <1>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+
+	elm0: ecc@25010000 {
+		compatible = "ti,am64-elm";
+		reg = <0x00 0x25010000 0x00 0x2000>;
+		interrupts = <GIC_SPI 132 IRQ_TYPE_LEVEL_HIGH>;
+		power-domains = <&k3_pds 54 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 54 0>;
+		clock-names = "fck";
+	};
 };
diff --git a/arch/arm64/boot/dts/ti/k3-am64-mcu.dtsi b/arch/arm64/boot/dts/ti/k3-am64-mcu.dtsi
index 2bb5c9ff172c..02d4285acbb8 100644
--- a/arch/arm64/boot/dts/ti/k3-am64-mcu.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am64-mcu.dtsi
@@ -10,7 +10,6 @@
 		compatible = "ti,am64-uart", "ti,am654-uart";
 		reg = <0x00 0x04a00000 0x00 0x100>;
 		interrupts = <GIC_SPI 185 IRQ_TYPE_LEVEL_HIGH>;
-		clock-frequency = <48000000>;
 		current-speed = <115200>;
 		power-domains = <&k3_pds 149 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&k3_clks 149 0>;
@@ -21,7 +20,6 @@
 		compatible = "ti,am64-uart", "ti,am654-uart";
 		reg = <0x00 0x04a10000 0x00 0x100>;
 		interrupts = <GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>;
-		clock-frequency = <48000000>;
 		current-speed = <115200>;
 		power-domains = <&k3_pds 160 TI_SCI_PD_EXCLUSIVE>;
 		clocks = <&k3_clks 160 0>;
diff --git a/arch/arm64/boot/dts/ti/k3-am64.dtsi b/arch/arm64/boot/dts/ti/k3-am64.dtsi
index 120974726be8..c858725133af 100644
--- a/arch/arm64/boot/dts/ti/k3-am64.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am64.dtsi
@@ -66,11 +66,14 @@
 		#address-cells = <2>;
 		#size-cells = <2>;
 		ranges = <0x00 0x000f4000 0x00 0x000f4000 0x00 0x000002d0>, /* PINCTRL */
+			 <0x00 0x00420000 0x00 0x00420000 0x00 0x00001000>, /* ESM0 */
 			 <0x00 0x00600000 0x00 0x00600000 0x00 0x00001100>, /* GPIO */
 			 <0x00 0x00a40000 0x00 0x00a40000 0x00 0x00000800>, /* Timesync router */
 			 <0x00 0x01000000 0x00 0x01000000 0x00 0x02330400>, /* First peripheral window */
 			 <0x00 0x08000000 0x00 0x08000000 0x00 0x00200000>, /* Main CPSW */
 			 <0x00 0x0d000000 0x00 0x0d000000 0x00 0x00800000>, /* PCIE_CORE */
+			 <0x00 0x0e000000 0x00 0x0e000000 0x00 0x00000100>, /* Main RTI0 */
+			 <0x00 0x0e010000 0x00 0x0e010000 0x00 0x00000100>, /* Main RTI1 */
 			 <0x00 0x0f000000 0x00 0x0f000000 0x00 0x00c44200>, /* Second peripheral window */
 			 <0x00 0x20000000 0x00 0x20000000 0x00 0x0a008000>, /* Third peripheral window */
 			 <0x00 0x30000000 0x00 0x30000000 0x00 0x000bc100>, /* ICSSG0/1 */
@@ -79,6 +82,7 @@
 			 <0x00 0x3b000000 0x00 0x3b000000 0x00 0x00000400>, /* GPMC0_CFG */
 			 <0x00 0x3cd00000 0x00 0x3cd00000 0x00 0x00000200>, /* TIMERMGR0_CONFIG */
 			 <0x00 0x3f004000 0x00 0x3f004000 0x00 0x00000400>, /* GICSS0_REGS */
+			 <0x00 0x40900000 0x00 0x40900000 0x00 0x00030000>, /* SA2_UL0 */
 			 <0x00 0x43000000 0x00 0x43000000 0x00 0x00020000>, /* CTRL_MMR0 */
 			 <0x00 0x44043000 0x00 0x44043000 0x00 0x00000fe0>, /* TI SCI DEBUG */
 			 <0x00 0x48000000 0x00 0x48000000 0x00 0x06400000>, /* DMASS */
@@ -87,6 +91,7 @@
 			 <0x00 0x68000000 0x00 0x68000000 0x00 0x08000000>, /* PCIe DAT0 */
 			 <0x00 0x70000000 0x00 0x70000000 0x00 0x00200000>, /* OC SRAM */
 			 <0x00 0x78000000 0x00 0x78000000 0x00 0x00800000>, /* Main R5FSS */
+			 <0x01 0x00000000 0x01 0x00000000 0x00 0x00310000>, /* A53 PERIPHBASE */
 			 <0x06 0x00000000 0x06 0x00000000 0x01 0x00000000>, /* PCIe DAT1 */
 			 <0x05 0x00000000 0x05 0x00000000 0x01 0x00000000>, /* FSS0 DAT3 */
 
diff --git a/arch/arm64/boot/dts/ti/k3-am642-evm.dts b/arch/arm64/boot/dts/ti/k3-am642-evm.dts
index 6726c4c7c28c..5cf913860f80 100644
--- a/arch/arm64/boot/dts/ti/k3-am642-evm.dts
+++ b/arch/arm64/boot/dts/ti/k3-am642-evm.dts
@@ -13,7 +13,7 @@
 #include "k3-am642.dtsi"
 
 / {
-	compatible =  "ti,am642-evm", "ti,am642";
+	compatible = "ti,am642-evm", "ti,am642";
 	model = "Texas Instruments AM642 EVM";
 
 	chosen {
@@ -184,6 +184,20 @@
 			};
 		};
 	};
+
+	transceiver1: can-phy0 {
+		compatible = "ti,tcan1042";
+		#phy-cells = <0>;
+		max-bitrate = <5000000>;
+		standby-gpios = <&exp1 8 GPIO_ACTIVE_HIGH>;
+	};
+
+	transceiver2: can-phy1 {
+		compatible = "ti,tcan1042";
+		#phy-cells = <0>;
+		max-bitrate = <5000000>;
+		standby-gpios = <&exp1 9 GPIO_ACTIVE_HIGH>;
+	};
 };
 
 &main_pmx0 {
@@ -294,6 +308,20 @@
 			AM64X_IOPAD(0x0270, PIN_INPUT, 0) /* (D18) ECAP0_IN_APWM_OUT */
 		>;
 	};
+
+	main_mcan0_pins_default: main-mcan0-pins-default {
+		pinctrl-single,pins = <
+			AM64X_IOPAD(0x0254, PIN_INPUT, 0) /* (B17) MCAN0_RX */
+			AM64X_IOPAD(0x0250, PIN_OUTPUT, 0) /* (A17) MCAN0_TX */
+		>;
+	};
+
+	main_mcan1_pins_default: main-mcan1-pins-default {
+		pinctrl-single,pins = <
+			AM64X_IOPAD(0x025c, PIN_INPUT, 0) /* (D17) MCAN1_RX */
+			AM64X_IOPAD(0x0258, PIN_OUTPUT, 0) /* (C17) MCAN1_TX */
+		>;
+	};
 };
 
 &main_uart0 {
@@ -470,7 +498,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&ospi0_pins_default>;
 
-	flash@0{
+	flash@0 {
 		compatible = "jedec,spi-nor";
 		reg = <0x0>;
 		spi-tx-bus-width = <8>;
@@ -481,8 +509,6 @@
 		cdns,tchsh-ns = <60>;
 		cdns,tslch-ns = <60>;
 		cdns,read-delay = <4>;
-		#address-cells = <1>;
-		#size-cells = <1>;
 	};
 };
 
@@ -638,3 +664,23 @@
 &icssg1_mdio {
 	status = "disabled";
 };
+
+&main_mcan0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_mcan0_pins_default>;
+	phys = <&transceiver1>;
+};
+
+&main_mcan1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_mcan1_pins_default>;
+	phys = <&transceiver2>;
+};
+
+&gpmc0 {
+	status = "disabled";
+};
+
+&elm0 {
+	status = "disabled";
+};
diff --git a/arch/arm64/boot/dts/ti/k3-am642-sk.dts b/arch/arm64/boot/dts/ti/k3-am642-sk.dts
index 6b04745147be..738d0cf6c40a 100644
--- a/arch/arm64/boot/dts/ti/k3-am642-sk.dts
+++ b/arch/arm64/boot/dts/ti/k3-am642-sk.dts
@@ -9,10 +9,11 @@
 #include <dt-bindings/phy/phy.h>
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/net/ti-dp83867.h>
+#include <dt-bindings/leds/common.h>
 #include "k3-am642.dtsi"
 
 / {
-	compatible =  "ti,am642-sk", "ti,am642";
+	compatible = "ti,am642-sk", "ti,am642";
 	model = "Texas Instruments AM642 SK";
 
 	chosen {
@@ -125,6 +126,99 @@
 		vin-supply = <&vcc_3v3_sys>;
 		gpio = <&exp1 3 GPIO_ACTIVE_HIGH>;
 	};
+
+	com8_ls_en: regulator-1 {
+		compatible = "regulator-fixed";
+		regulator-name = "com8_ls_en";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+		regulator-boot-on;
+		pinctrl-0 = <&main_com8_ls_en_pins_default>;
+		pinctrl-names = "default";
+		gpio = <&main_gpio0 62 GPIO_ACTIVE_LOW>;
+	};
+
+	wlan_en: regulator-2 {
+		/* output of SN74AVC4T245RSVR */
+		compatible = "regulator-fixed";
+		regulator-name = "wlan_en";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		enable-active-high;
+		pinctrl-0 = <&main_wlan_en_pins_default>;
+		pinctrl-names = "default";
+		vin-supply = <&com8_ls_en>;
+		gpio = <&main_gpio0 48 GPIO_ACTIVE_HIGH>;
+	};
+
+	led-controller {
+		compatible = "gpio-leds";
+
+		led-0 {
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_INDICATOR;
+			function-enumerator = <1>;
+			gpios = <&exp2 0 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		led-1 {
+			color = <LED_COLOR_ID_RED>;
+			function = LED_FUNCTION_INDICATOR;
+			function-enumerator = <2>;
+			gpios = <&exp2 1 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		led-2 {
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_INDICATOR;
+			function-enumerator = <3>;
+			gpios = <&exp2 2 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		led-3 {
+			color = <LED_COLOR_ID_AMBER>;
+			function = LED_FUNCTION_INDICATOR;
+			function-enumerator = <4>;
+			gpios = <&exp2 3 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		led-4 {
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_INDICATOR;
+			function-enumerator = <5>;
+			gpios = <&exp2 4 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		led-5 {
+			color = <LED_COLOR_ID_RED>;
+			function = LED_FUNCTION_INDICATOR;
+			function-enumerator = <6>;
+			gpios = <&exp2 5 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		led-6 {
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_INDICATOR;
+			function-enumerator = <7>;
+			gpios = <&exp2 6 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		led-7 {
+			color = <LED_COLOR_ID_AMBER>;
+			function = LED_FUNCTION_HEARTBEAT;
+			function-enumerator = <8>;
+			linux,default-trigger = "heartbeat";
+			gpios = <&exp2 7 GPIO_ACTIVE_HIGH>;
+		};
+	};
 };
 
 &main_pmx0 {
@@ -141,6 +235,15 @@
 		>;
 	};
 
+	main_uart0_pins_default: main-uart0-pins-default {
+		pinctrl-single,pins = <
+			AM64X_IOPAD(0x0238, PIN_INPUT, 0) /* (B16) UART0_CTSn */
+			AM64X_IOPAD(0x023c, PIN_OUTPUT, 0) /* (A16) UART0_RTSn */
+			AM64X_IOPAD(0x0230, PIN_INPUT, 0) /* (D15) UART0_RXD */
+			AM64X_IOPAD(0x0234, PIN_OUTPUT, 0) /* (C16) UART0_TXD */
+		>;
+	};
+
 	main_usb0_pins_default: main-usb0-pins-default {
 		pinctrl-single,pins = <
 			AM64X_IOPAD(0x02a8, PIN_OUTPUT, 0) /* (E19) USB0_DRVVBUS */
@@ -216,6 +319,23 @@
 			AM64X_IOPAD(0x0270, PIN_INPUT, 0) /* (D18) ECAP0_IN_APWM_OUT */
 		>;
 	};
+	main_wlan_en_pins_default: main-wlan-en-pins-default {
+		pinctrl-single,pins = <
+			AM64X_IOPAD(0x00c4, PIN_OUTPUT_PULLUP, 7) /* (V8) GPIO0_48 */
+		>;
+	};
+
+	main_com8_ls_en_pins_default: main-com8-ls-en-pins-default {
+		pinctrl-single,pins = <
+			AM64X_IOPAD(0x00fc, PIN_OUTPUT, 7) /* (U7) PRG1_PRU0_GPO17.GPIO0_62 */
+		>;
+	};
+
+	main_wlan_pins_default: main-wlan-pins-default {
+		pinctrl-single,pins = <
+			AM64X_IOPAD(0x00bc, PIN_INPUT, 7) /* (U8) GPIO0_46 */
+		>;
+	};
 };
 
 &mcu_uart0 {
@@ -226,6 +346,11 @@
 	status = "disabled";
 };
 
+&main_uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_uart0_pins_default>;
+};
+
 &main_uart1 {
 	/* main_uart1 is reserved for firmware usage */
 	status = "reserved";
@@ -274,6 +399,14 @@
 				  "VPP_LDO_EN", "RPI_PS_3V3_En",
 				  "RPI_PS_5V0_En", "RPI_HAT_DETECT";
 	};
+
+	exp2: gpio@60 {
+		compatible = "ti,tpic2810";
+		reg = <0x60>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names = "LED1","LED2","LED3","LED4","LED5","LED6","LED7","LED8";
+	};
 };
 
 &main_i2c3 {
@@ -293,6 +426,26 @@
 	status = "reserved";
 };
 
+&sdhci0 {
+	vmmc-supply = <&wlan_en>;
+	bus-width = <4>;
+	non-removable;
+	cap-power-off-card;
+	keep-power-in-suspend;
+	ti,driver-strength-ohm = <50>;
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+	wlcore: wlcore@2 {
+		compatible = "ti,wl1837";
+		reg = <2>;
+		pinctrl-0 = <&main_wlan_pins_default>;
+		pinctrl-names = "default";
+		interrupt-parent = <&main_gpio0>;
+		interrupts = <46 IRQ_TYPE_EDGE_FALLING>;
+	};
+};
+
 &sdhci1 {
 	/* SD/MMC */
 	vmmc-supply = <&vdd_mmc1>;
@@ -369,7 +522,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&ospi0_pins_default>;
 
-	flash@0{
+	flash@0 {
 		compatible = "jedec,spi-nor";
 		reg = <0x0>;
 		spi-tx-bus-width = <8>;
@@ -380,8 +533,6 @@
 		cdns,tchsh-ns = <60>;
 		cdns,tslch-ns = <60>;
 		cdns,read-delay = <4>;
-		#address-cells = <1>;
-		#size-cells = <1>;
 	};
 };
 
@@ -525,3 +676,19 @@
 &icssg1_mdio {
 	status = "disabled";
 };
+
+&main_mcan0 {
+	status = "disabled";
+};
+
+&main_mcan1 {
+	status = "disabled";
+};
+
+&gpmc0 {
+	status = "disabled";
+};
+
+&elm0 {
+	status = "disabled";
+};
diff --git a/arch/arm64/boot/dts/ti/k3-am642.dtsi b/arch/arm64/boot/dts/ti/k3-am642.dtsi
index e2b397c88401..8a76f4821b11 100644
--- a/arch/arm64/boot/dts/ti/k3-am642.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am642.dtsi
@@ -60,6 +60,6 @@
 		cache-level = <2>;
 		cache-size = <0x40000>;
 		cache-line-size = <64>;
-		cache-sets = <512>;
+		cache-sets = <256>;
 	};
 };
diff --git a/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi b/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
index 65da226847f4..32b797237581 100644
--- a/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am65-iot2050-common.dtsi
@@ -425,7 +425,7 @@
 
 	psu: regulator@60 {
 		compatible = "ti,tps62363";
-		reg =  <0x60>;
+		reg = <0x60>;
 		regulator-name = "tps62363-vout";
 		regulator-min-microvolt = <500000>;
 		regulator-max-microvolt = <1500000>;
@@ -574,7 +574,7 @@
 	pinctrl-0 = <&mcu_spi0_pins_default>;
 
 	#address-cells = <1>;
-	#size-cells= <0>;
+	#size-cells = <0>;
 	ti,pindir-d0-out-d1-in;
 };
 
@@ -603,8 +603,6 @@
 		cdns,tchsh-ns = <60>;
 		cdns,tslch-ns = <60>;
 		cdns,read-delay = <2>;
-		#address-cells = <1>;
-		#size-cells = <1>;
 	};
 };
 
@@ -646,6 +644,14 @@
 	reset-gpios = <&wkup_gpio0 27 GPIO_ACTIVE_HIGH>;
 };
 
+&m_can0 {
+	status = "disabled";
+};
+
+&m_can1 {
+	status = "disabled";
+};
+
 &pcie1_ep {
 	status = "disabled";
 };
@@ -731,3 +737,15 @@
 &icssg2_mdio {
 	status = "disabled";
 };
+
+&mcasp0 {
+	status = "disabled";
+};
+
+&mcasp1 {
+	status = "disabled";
+};
+
+&mcasp2 {
+	status = "disabled";
+};
diff --git a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
index ce8bb4a61011..4005a73cfea9 100644
--- a/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am65-main.dtsi
@@ -35,7 +35,10 @@
 		#interrupt-cells = <3>;
 		interrupt-controller;
 		reg = <0x00 0x01800000 0x00 0x10000>,	/* GICD */
-		      <0x00 0x01880000 0x00 0x90000>;	/* GICR */
+		      <0x00 0x01880000 0x00 0x90000>,	/* GICR */
+		      <0x00 0x6f000000 0x00 0x2000>,	/* GICC */
+		      <0x00 0x6f010000 0x00 0x1000>,	/* GICH */
+		      <0x00 0x6f020000 0x00 0x2000>;	/* GICV */
 		/*
 		 * vcpumntirq:
 		 * virtual CPU interface maintenance interrupt
@@ -109,13 +112,13 @@
 	crypto: crypto@4e00000 {
 		compatible = "ti,am654-sa2ul";
 		reg = <0x0 0x4e00000 0x0 0x1200>;
-		power-domains = <&k3_pds 136 TI_SCI_PD_EXCLUSIVE>;
+		power-domains = <&k3_pds 136 TI_SCI_PD_SHARED>;
 		#address-cells = <2>;
 		#size-cells = <2>;
 		ranges = <0x0 0x04e00000 0x00 0x04e00000 0x0 0x30000>;
 
-		dmas = <&main_udmap 0xc000>, <&main_udmap 0x4000>,
-				<&main_udmap 0x4001>;
+		dmas = <&main_udmap 0xc001>, <&main_udmap 0x4002>,
+				<&main_udmap 0x4003>;
 		dma-names = "tx", "rx1", "rx2";
 		dma-coherent;
 
@@ -124,6 +127,7 @@
 			reg = <0x0 0x4e10000 0x0 0x7d>;
 			interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&k3_clks 136 1>;
+			status = "disabled"; /* Used by OP-TEE */
 		};
 	};
 
@@ -687,7 +691,7 @@
 
 	pcie0_rc: pcie@5500000 {
 		compatible = "ti,am654-pcie-rc";
-		reg =  <0x0 0x5500000 0x0 0x1000>, <0x0 0x5501000 0x0 0x1000>, <0x0 0x10000000 0x0 0x2000>, <0x0 0x5506000 0x0 0x1000>;
+		reg = <0x0 0x5500000 0x0 0x1000>, <0x0 0x5501000 0x0 0x1000>, <0x0 0x10000000 0x0 0x2000>, <0x0 0x5506000 0x0 0x1000>;
 		reg-names = "app", "dbics", "config", "atu";
 		power-domains = <&k3_pds 120 TI_SCI_PD_EXCLUSIVE>;
 		#address-cells = <3>;
@@ -707,7 +711,7 @@
 
 	pcie0_ep: pcie-ep@5500000 {
 		compatible = "ti,am654-pcie-ep";
-		reg =  <0x0 0x5500000 0x0 0x1000>, <0x0 0x5501000 0x0 0x1000>, <0x0 0x10000000 0x0 0x8000000>, <0x0 0x5506000 0x0 0x1000>;
+		reg = <0x0 0x5500000 0x0 0x1000>, <0x0 0x5501000 0x0 0x1000>, <0x0 0x10000000 0x0 0x8000000>, <0x0 0x5506000 0x0 0x1000>;
 		reg-names = "app", "dbics", "addr_space", "atu";
 		power-domains = <&k3_pds 120 TI_SCI_PD_EXCLUSIVE>;
 		ti,syscon-pcie-mode = <&pcie0_mode>;
@@ -720,7 +724,7 @@
 
 	pcie1_rc: pcie@5600000 {
 		compatible = "ti,am654-pcie-rc";
-		reg =  <0x0 0x5600000 0x0 0x1000>, <0x0 0x5601000 0x0 0x1000>, <0x0 0x18000000 0x0 0x2000>, <0x0 0x5606000 0x0 0x1000>;
+		reg = <0x0 0x5600000 0x0 0x1000>, <0x0 0x5601000 0x0 0x1000>, <0x0 0x18000000 0x0 0x2000>, <0x0 0x5606000 0x0 0x1000>;
 		reg-names = "app", "dbics", "config", "atu";
 		power-domains = <&k3_pds 121 TI_SCI_PD_EXCLUSIVE>;
 		#address-cells = <3>;
@@ -740,7 +744,7 @@
 
 	pcie1_ep: pcie-ep@5600000 {
 		compatible = "ti,am654-pcie-ep";
-		reg =  <0x0 0x5600000 0x0 0x1000>, <0x0 0x5601000 0x0 0x1000>, <0x0 0x18000000 0x0 0x4000000>, <0x0 0x5606000 0x0 0x1000>;
+		reg = <0x0 0x5600000 0x0 0x1000>, <0x0 0x5601000 0x0 0x1000>, <0x0 0x18000000 0x0 0x4000000>, <0x0 0x5606000 0x0 0x1000>;
 		reg-names = "app", "dbics", "addr_space", "atu";
 		power-domains = <&k3_pds 121 TI_SCI_PD_EXCLUSIVE>;
 		ti,syscon-pcie-mode = <&pcie1_mode>;
@@ -840,9 +844,9 @@
 
 		power-domains = <&k3_pds 67 TI_SCI_PD_EXCLUSIVE>;
 
-		clocks =	<&k3_clks 67 1>,
-				<&k3_clks 216 1>,
-				<&k3_clks 67 2>;
+		clocks = <&k3_clks 67 1>,
+			 <&k3_clks 216 1>,
+			 <&k3_clks 67 2>;
 		clock-names = "fck", "vp1", "vp2";
 
 		/*
diff --git a/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi b/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi
index c93ff1520a0e..8d592bf41d6f 100644
--- a/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am65-mcu.dtsi
@@ -159,6 +159,36 @@
 		};
 	};
 
+	m_can0: mcan@40528000 {
+		compatible = "bosch,m_can";
+		reg = <0x0 0x40528000 0x0 0x400>,
+		      <0x0 0x40500000 0x0 0x4400>;
+		reg-names = "m_can", "message_ram";
+		power-domains = <&k3_pds 102 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 102 5>, <&k3_clks 102 0>;
+		clock-names = "hclk", "cclk";
+		interrupt-parent = <&gic500>;
+		interrupts = <GIC_SPI 544 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 545 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "int0", "int1";
+		bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
+	};
+
+	m_can1: mcan@40568000 {
+		compatible = "bosch,m_can";
+		reg = <0x0 0x40568000 0x0 0x400>,
+		      <0x0 0x40540000 0x0 0x4400>;
+		reg-names = "m_can", "message_ram";
+		power-domains = <&k3_pds 103 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 103 5>, <&k3_clks 103 0>;
+		clock-names = "hclk", "cclk";
+		interrupt-parent = <&gic500>;
+		interrupts = <GIC_SPI 547 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 548 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "int0", "int1";
+		bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
+	};
+
 	fss: fss@47000000 {
 		compatible = "simple-bus";
 		#address-cells = <2>;
diff --git a/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi
index 9c69d0917f69..fa11d7142006 100644
--- a/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am65-wakeup.dtsi
@@ -12,8 +12,8 @@
 
 		mbox-names = "rx", "tx";
 
-		mboxes= <&secure_proxy_main 11>,
-			<&secure_proxy_main 13>;
+		mboxes = <&secure_proxy_main 11>,
+			 <&secure_proxy_main 13>;
 
 		reg-names = "debug_messages";
 		reg = <0x44083000 0x1000>;
diff --git a/arch/arm64/boot/dts/ti/k3-am65.dtsi b/arch/arm64/boot/dts/ti/k3-am65.dtsi
index a58a39fa42db..c538a0bf3cdd 100644
--- a/arch/arm64/boot/dts/ti/k3-am65.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am65.dtsi
@@ -86,6 +86,7 @@
 			 <0x00 0x46000000 0x00 0x46000000 0x00 0x00200000>,
 			 <0x00 0x47000000 0x00 0x47000000 0x00 0x00068400>,
 			 <0x00 0x50000000 0x00 0x50000000 0x00 0x8000000>,
+			 <0x00 0x6f000000 0x00 0x6f000000 0x00 0x00310000>, /* A53 PERIPHBASE */
 			 <0x00 0x70000000 0x00 0x70000000 0x00 0x200000>,
 			 <0x05 0x00000000 0x05 0x00000000 0x01 0x0000000>,
 			 <0x07 0x00000000 0x07 0x00000000 0x01 0x0000000>;
diff --git a/arch/arm64/boot/dts/ti/k3-am654-base-board.dts b/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
index cfbcebfa37c1..5850582dd4ed 100644
--- a/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
@@ -10,7 +10,7 @@
 #include <dt-bindings/net/ti-dp83867.h>
 
 / {
-	compatible =  "ti,am654-evm", "ti,am654";
+	compatible = "ti,am654-evm", "ti,am654";
 	model = "Texas Instruments AM654 Base Board";
 
 	chosen {
@@ -73,13 +73,13 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&push_button_pins_default>;
 
-		sw5 {
+		switch-5 {
 			label = "GPIO Key USER1";
 			linux,code = <BTN_0>;
 			gpios = <&wkup_gpio0 24 GPIO_ACTIVE_LOW>;
 		};
 
-		sw6 {
+		switch-6 {
 			label = "GPIO Key USER2";
 			linux,code = <BTN_1>;
 			gpios = <&wkup_gpio0 27 GPIO_ACTIVE_LOW>;
@@ -330,17 +330,15 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&main_spi0_pins_default>;
 	#address-cells = <1>;
-	#size-cells= <0>;
+	#size-cells = <0>;
 	ti,pindir-d0-out-d1-in;
 
-	flash@0{
+	flash@0 {
 		compatible = "jedec,spi-nor";
 		reg = <0x0>;
 		spi-tx-bus-width = <1>;
 		spi-rx-bus-width = <1>;
 		spi-max-frequency = <48000000>;
-		#address-cells = <1>;
-		#size-cells= <1>;
 	};
 };
 
@@ -416,6 +414,14 @@
 	status = "disabled";
 };
 
+&m_can0 {
+	status = "disabled";
+};
+
+&m_can1 {
+	status = "disabled";
+};
+
 &mailbox0_cluster0 {
 	interrupts = <436>;
 
@@ -490,7 +496,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&mcu_fss0_ospi0_pins_default>;
 
-	flash@0{
+	flash@0 {
 		compatible = "jedec,spi-nor";
 		reg = <0x0>;
 		spi-tx-bus-width = <8>;
@@ -501,8 +507,6 @@
 		cdns,tchsh-ns = <60>;
 		cdns,tslch-ns = <60>;
 		cdns,read-delay = <0>;
-		#address-cells = <1>;
-		#size-cells = <1>;
 	};
 };
 
diff --git a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
index 121975dc8239..7e8552fd2b6a 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
@@ -134,15 +134,17 @@
 		>;
 	};
 
-	main_usbss0_pins_default: main-usbss0-pins-default {
+	vdd_sd_dv_pins_default: vdd-sd-dv-pins-default {
 		pinctrl-single,pins = <
-			J721E_IOPAD(0x120, PIN_OUTPUT, 0) /* (T4) USB0_DRVVBUS */
+			J721E_IOPAD(0xd0, PIN_OUTPUT, 7) /* (T5) SPI0_D1.GPIO0_55 */
 		>;
 	};
+};
 
-	vdd_sd_dv_pins_default: vdd-sd-dv-pins-default {
+&main_pmx1 {
+	main_usbss0_pins_default: main-usbss0-pins-default {
 		pinctrl-single,pins = <
-			J721E_IOPAD(0xd0, PIN_OUTPUT, 7) /* (T5) SPI0_D1.GPIO0_55 */
+			J721E_IOPAD(0x04, PIN_OUTPUT, 0) /* (T4) USB0_DRVVBUS */
 		>;
 	};
 };
diff --git a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
index d60ef4f7dd0b..80a57916bcb3 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j7200-main.dtsi
@@ -32,7 +32,7 @@
 		#size-cells = <1>;
 		ranges = <0x00 0x00 0x00100000 0x1c000>;
 
-		serdes_ln_ctrl: serdes-ln-ctrl@4080 {
+		serdes_ln_ctrl: mux-controller@4080 {
 			compatible = "mmio-mux";
 			#mux-control-cells = <1>;
 			mux-reg-masks = <0x4080 0x3>, <0x4084 0x3>, /* SERDES0 lane0/1 select */
@@ -54,7 +54,10 @@
 		#interrupt-cells = <3>;
 		interrupt-controller;
 		reg = <0x00 0x01800000 0x00 0x10000>,	/* GICD */
-		      <0x00 0x01900000 0x00 0x100000>;	/* GICR */
+		      <0x00 0x01900000 0x00 0x100000>,	/* GICR */
+		      <0x00 0x6f000000 0x00 0x2000>,	/* GICC */
+		      <0x00 0x6f010000 0x00 0x1000>,	/* GICH */
+		      <0x00 0x6f020000 0x00 0x2000>;	/* GICV */
 
 		/* vcpumntirq: virtual CPU interface maintenance interrupt */
 		interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
@@ -292,7 +295,16 @@
 	main_pmx0: pinctrl@11c000 {
 		compatible = "pinctrl-single";
 		/* Proxy 0 addressing */
-		reg = <0x00 0x11c000 0x00 0x2b4>;
+		reg = <0x00 0x11c000 0x00 0x10c>;
+		#pinctrl-cells = <1>;
+		pinctrl-single,register-width = <32>;
+		pinctrl-single,function-mask = <0xffffffff>;
+	};
+
+	main_pmx1: pinctrl@11c11c {
+		compatible = "pinctrl-single";
+		/* Proxy 0 addressing */
+		reg = <0x00 0x11c11c 0x00 0xc>;
 		#pinctrl-cells = <1>;
 		pinctrl-single,register-width = <32>;
 		pinctrl-single,function-mask = <0xffffffff>;
@@ -736,6 +748,24 @@
 		clock-names = "gpio";
 	};
 
+	watchdog0: watchdog@2200000 {
+		compatible = "ti,j7-rti-wdt";
+		reg = <0x0 0x2200000 0x0 0x100>;
+		clocks = <&k3_clks 252 1>;
+		power-domains = <&k3_pds 252 TI_SCI_PD_EXCLUSIVE>;
+		assigned-clocks = <&k3_clks 252 1>;
+		assigned-clock-parents = <&k3_clks 252 5>;
+	};
+
+	watchdog1: watchdog@2210000 {
+		compatible = "ti,j7-rti-wdt";
+		reg = <0x0 0x2210000 0x0 0x100>;
+		clocks = <&k3_clks 253 1>;
+		power-domains = <&k3_pds 253 TI_SCI_PD_EXCLUSIVE>;
+		assigned-clocks = <&k3_clks 253 1>;
+		assigned-clock-parents = <&k3_clks 253 5>;
+	};
+
 	main_r5fss0: r5fss@5c00000 {
 		compatible = "ti,j7200-r5fss";
 		ti,cluster-mode = <1>;
diff --git a/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi
index 1044ec6c4b0d..e5be78a58682 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi
@@ -12,8 +12,8 @@
 
 		mbox-names = "rx", "tx";
 
-		mboxes= <&secure_proxy_main 11>,
-			<&secure_proxy_main 13>;
+		mboxes = <&secure_proxy_main 11>,
+			 <&secure_proxy_main 13>;
 
 		reg-names = "debug_messages";
 		reg = <0x00 0x44083000 0x00 0x1000>;
@@ -375,4 +375,24 @@
 			ti,loczrama = <1>;
 		};
 	};
+
+	mcu_crypto: crypto@40900000 {
+		compatible = "ti,j721e-sa2ul";
+		reg = <0x00 0x40900000 0x00 0x1200>;
+		power-domains = <&k3_pds 265 TI_SCI_PD_SHARED>;
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges = <0x00 0x40900000 0x00 0x40900000 0x00 0x30000>;
+		dmas = <&mcu_udmap 0xf501>, <&mcu_udmap 0x7502>,
+		       <&mcu_udmap 0x7503>;
+		dma-names = "tx", "rx1", "rx2";
+		dma-coherent;
+
+		rng: rng@40910000 {
+			compatible = "inside-secure,safexcel-eip76";
+			reg = <0x00 0x40910000 0x00 0x7d>;
+			interrupts = <GIC_SPI 945 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled"; /* Used by OP-TEE */
+		};
+	};
 };
diff --git a/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi
index 34724440171a..2d615c3e9fa1 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi
@@ -256,7 +256,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&mcu_fss0_ospi0_pins_default>;
 
-	flash@0{
+	flash@0 {
 		compatible = "jedec,spi-nor";
 		reg = <0x0>;
 		spi-tx-bus-width = <8>;
@@ -267,7 +267,5 @@
 		cdns,tchsh-ns = <60>;
 		cdns,tslch-ns = <60>;
 		cdns,read-delay = <4>;
-		#address-cells = <1>;
-		#size-cells = <1>;
 	};
 };
diff --git a/arch/arm64/boot/dts/ti/k3-j7200.dtsi b/arch/arm64/boot/dts/ti/k3-j7200.dtsi
index 47567cb260c2..b6da0454cc5b 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j7200.dtsi
@@ -62,7 +62,7 @@
 			i-cache-sets = <256>;
 			d-cache-size = <0x8000>;
 			d-cache-line-size = <64>;
-			d-cache-sets = <128>;
+			d-cache-sets = <256>;
 			next-level-cache = <&L2_0>;
 		};
 
@@ -76,7 +76,7 @@
 			i-cache-sets = <256>;
 			d-cache-size = <0x8000>;
 			d-cache-line-size = <64>;
-			d-cache-sets = <128>;
+			d-cache-sets = <256>;
 			next-level-cache = <&L2_0>;
 		};
 	};
@@ -86,7 +86,7 @@
 		cache-level = <2>;
 		cache-size = <0x100000>;
 		cache-line-size = <64>;
-		cache-sets = <2048>;
+		cache-sets = <1024>;
 		next-level-cache = <&msmc_l3>;
 	};
 
@@ -129,6 +129,7 @@
 			 <0x00 0x00a40000 0x00 0x00a40000 0x00 0x00000800>, /* timesync router */
 			 <0x00 0x01000000 0x00 0x01000000 0x00 0x0d000000>, /* Most peripherals */
 			 <0x00 0x30000000 0x00 0x30000000 0x00 0x0c400000>, /* MAIN NAVSS */
+			 <0x00 0x6f000000 0x00 0x6f000000 0x00 0x00310000>, /* A72 PERIPHBASE */
 			 <0x00 0x70000000 0x00 0x70000000 0x00 0x00800000>, /* MSMC RAM */
 			 <0x00 0x18000000 0x00 0x18000000 0x00 0x08000000>, /* PCIe1 DAT0 */
 			 <0x41 0x00000000 0x41 0x00000000 0x01 0x00000000>, /* PCIe1 DAT1 */
diff --git a/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts
index dc2bc67f9f48..b1691ac3442d 100644
--- a/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts
@@ -26,13 +26,13 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&sw10_button_pins_default &sw11_button_pins_default>;
 
-		sw10: sw10 {
+		sw10: switch-10 {
 			label = "GPIO Key USER1";
 			linux,code = <BTN_0>;
 			gpios = <&main_gpio0 0 GPIO_ACTIVE_LOW>;
 		};
 
-		sw11: sw11 {
+		sw11: switch-11 {
 			label = "GPIO Key USER2";
 			linux,code = <BTN_1>;
 			gpios = <&wkup_gpio0 7 GPIO_ACTIVE_LOW>;
@@ -112,6 +112,64 @@
 			      "cpb-codec-scki",
 			      "cpb-codec-scki-48000", "cpb-codec-scki-44100";
 	};
+
+	transceiver1: can-phy0 {
+		compatible = "ti,tcan1043";
+		#phy-cells = <0>;
+		max-bitrate = <5000000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&mcu_mcan0_gpio_pins_default>;
+		standby-gpios = <&wkup_gpio0 54 GPIO_ACTIVE_LOW>;
+		enable-gpios = <&wkup_gpio0 0 GPIO_ACTIVE_HIGH>;
+	};
+
+	transceiver2: can-phy1 {
+		compatible = "ti,tcan1042";
+		#phy-cells = <0>;
+		max-bitrate = <5000000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&mcu_mcan1_gpio_pins_default>;
+		standby-gpios = <&wkup_gpio0 2 GPIO_ACTIVE_HIGH>;
+	};
+
+	transceiver3: can-phy2 {
+		compatible = "ti,tcan1043";
+		#phy-cells = <0>;
+		max-bitrate = <5000000>;
+		standby-gpios = <&exp2 7 GPIO_ACTIVE_LOW>;
+		enable-gpios = <&exp2 6 GPIO_ACTIVE_HIGH>;
+	};
+
+	transceiver4: can-phy3 {
+		compatible = "ti,tcan1042";
+		#phy-cells = <0>;
+		max-bitrate = <5000000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&main_mcan2_gpio_pins_default>;
+		standby-gpios = <&main_gpio0 127 GPIO_ACTIVE_HIGH>;
+	};
+
+	dp_pwr_3v3: regulator-dp-pwr {
+		compatible = "regulator-fixed";
+		regulator-name = "dp-pwr";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&exp4 0 GPIO_ACTIVE_HIGH>; /* P0 - DP0_PWR_SW_EN */
+		enable-active-high;
+	};
+
+	dp0: connector {
+		compatible = "dp-connector";
+		label = "DP0";
+		type = "full-size";
+		dp-pwr-supply = <&dp_pwr_3v3>;
+
+		port {
+			dp_connector_in: endpoint {
+				remote-endpoint = <&dp0_out>;
+			};
+		};
+	};
 };
 
 &main_pmx0 {
@@ -154,6 +212,12 @@
 		>;
 	};
 
+	dp0_pins_default: dp0-pins-default {
+		pinctrl-single,pins = <
+			J721E_IOPAD(0x1c4, PIN_INPUT, 5) /* SPI0_CS1.DP0_HPD */
+		>;
+	};
+
 	main_i2c1_exp4_pins_default: main-i2c1-exp4-pins-default {
 		pinctrl-single,pins = <
 			J721E_IOPAD(0x230, PIN_INPUT, 7) /* (U2) ECAP0_IN_APWM_OUT.GPIO1_11 */
@@ -207,6 +271,26 @@
 			J721E_IOPAD(0x1a4, PIN_OUTPUT, 3) /* (W26) RGMII6_RXC.AUDIO_EXT_REFCLK2 */
 		>;
 	};
+
+	main_mcan0_pins_default: main-mcan0-pins-default {
+		pinctrl-single,pins = <
+			J721E_IOPAD(0x208, PIN_INPUT, 0) /* (W5) MCAN0_RX */
+			J721E_IOPAD(0x20c, PIN_OUTPUT, 0) /* (W6) MCAN0_TX */
+		>;
+	};
+
+	main_mcan2_pins_default: main-mcan2-pins-default {
+		pinctrl-single,pins = <
+			J721E_IOPAD(0x01f0, PIN_INPUT, 3) /* (AC2) MCAN2_RX.GPIO0_123 */
+			J721E_IOPAD(0x01f4, PIN_OUTPUT, 3) /* (AB1) MCAN2_TX.GPIO0_124 */
+		>;
+	};
+
+	main_mcan2_gpio_pins_default: main-mcan2-gpio-pins-default {
+		pinctrl-single,pins = <
+			J721E_IOPAD(0x200, PIN_INPUT, 7) /* (AC4) UART1_CTSn.GPIO0_127 */
+		>;
+	};
 };
 
 &wkup_pmx0 {
@@ -252,6 +336,33 @@
 			J721E_WKUP_IOPAD(0x0088, PIN_INPUT, 0) /* MCU_MDIO0_MDIO */
 		>;
 	};
+
+	mcu_mcan0_pins_default: mcu-mcan0-pins-default {
+		pinctrl-single,pins = <
+			J721E_WKUP_IOPAD(0xac, PIN_INPUT, 0) /* (C29) MCU_MCAN0_RX */
+			J721E_WKUP_IOPAD(0xa8, PIN_OUTPUT, 0) /* (D29) MCU_MCAN0_TX */
+		>;
+	};
+
+	mcu_mcan0_gpio_pins_default: mcu-mcan0-gpio-pins-default {
+		pinctrl-single,pins = <
+			J721E_WKUP_IOPAD(0xb0, PIN_INPUT, 7) /* (F26) WKUP_GPIO0_0 */
+			J721E_WKUP_IOPAD(0x98, PIN_INPUT, 7) /* (E28) MCU_SPI0_D1.WKUP_GPIO0_54 */
+		>;
+	};
+
+	mcu_mcan1_pins_default: mcu-mcan1-pins-default {
+		pinctrl-single,pins = <
+			J721E_WKUP_IOPAD(0xc4, PIN_INPUT, 0) /* (G24) WKUP_GPIO0_5.MCU_MCAN1_RX */
+			J721E_WKUP_IOPAD(0xc0, PIN_OUTPUT, 0) /* (G25) WKUP_GPIO0_4.MCU_MCAN1_TX */
+		>;
+	};
+
+	mcu_mcan1_gpio_pins_default: mcu-mcan1-gpio-pins-default {
+		pinctrl-single,pins = <
+			J721E_WKUP_IOPAD(0xb8, PIN_INPUT, 7) /* (F28) WKUP_GPIO0_2 */
+		>;
+	};
 };
 
 &wkup_uart0 {
@@ -399,7 +510,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&mcu_fss0_ospi1_pins_default>;
 
-	flash@0{
+	flash@0 {
 		compatible = "jedec,spi-nor";
 		reg = <0x0>;
 		spi-tx-bus-width = <1>;
@@ -410,8 +521,6 @@
 		cdns,tchsh-ns = <60>;
 		cdns,tslch-ns = <60>;
 		cdns,read-delay = <2>;
-		#address-cells = <1>;
-		#size-cells = <1>;
 	};
 };
 
@@ -577,6 +686,33 @@
 				 <&k3_clks 152 18>;	/* PLL23_HSDIV0 */
 };
 
+&dss_ports {
+	port {
+		dpi0_out: endpoint {
+			remote-endpoint = <&dp0_in>;
+		};
+	};
+};
+
+&dp0_ports {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	port@0 {
+		reg = <0>;
+		dp0_in: endpoint {
+			remote-endpoint = <&dpi0_out>;
+		};
+	};
+
+	port@4 {
+		reg = <4>;
+		dp0_out: endpoint {
+			remote-endpoint = <&dp_connector_in>;
+		};
+	};
+};
+
 &mcasp0 {
 	status = "disabled";
 };
@@ -712,6 +848,24 @@
 	};
 };
 
+&serdes4 {
+	torrent_phy_dp: phy@0 {
+		reg = <0>;
+		resets = <&serdes_wiz4 1>;
+		cdns,phy-type = <PHY_TYPE_DP>;
+		cdns,num-lanes = <4>;
+		cdns,max-bit-rate = <5400>;
+		#phy-cells = <0>;
+	};
+};
+
+&mhdp {
+	phys = <&torrent_phy_dp>;
+	phy-names = "dpphy";
+	pinctrl-names = "default";
+	pinctrl-0 = <&dp0_pins_default>;
+};
+
 &pcie0_rc {
 	reset-gpios = <&exp1 6 GPIO_ACTIVE_HIGH>;
 	phys = <&serdes0_pcie_link>;
@@ -762,14 +916,82 @@
 	status = "disabled";
 };
 
-&dss {
+&icssg0_mdio {
 	status = "disabled";
 };
 
-&icssg0_mdio {
+&icssg1_mdio {
 	status = "disabled";
 };
 
-&icssg1_mdio {
+&mcu_mcan0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcu_mcan0_pins_default>;
+	phys = <&transceiver1>;
+};
+
+&mcu_mcan1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcu_mcan1_pins_default>;
+	phys = <&transceiver2>;
+};
+
+&main_mcan0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_mcan0_pins_default>;
+	phys = <&transceiver3>;
+};
+
+&main_mcan1 {
+	status = "disabled";
+};
+
+&main_mcan2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_mcan2_pins_default>;
+	phys = <&transceiver4>;
+};
+
+&main_mcan3 {
+	status = "disabled";
+};
+
+&main_mcan4 {
+	status = "disabled";
+};
+
+&main_mcan5 {
+	status = "disabled";
+};
+
+&main_mcan6 {
+	status = "disabled";
+};
+
+&main_mcan7 {
+	status = "disabled";
+};
+
+&main_mcan8 {
+	status = "disabled";
+};
+
+&main_mcan9 {
+	status = "disabled";
+};
+
+&main_mcan10 {
+	status = "disabled";
+};
+
+&main_mcan11 {
+	status = "disabled";
+};
+
+&main_mcan12 {
+	status = "disabled";
+};
+
+&main_mcan13 {
 	status = "disabled";
 };
diff --git a/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi b/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
index 08c8d1b47dcd..917c9dc99efa 100644
--- a/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721e-main.dtsi
@@ -5,6 +5,7 @@
  * Copyright (C) 2016-2020 Texas Instruments Incorporated - https://www.ti.com/
  */
 #include <dt-bindings/phy/phy.h>
+#include <dt-bindings/phy/phy-ti.h>
 #include <dt-bindings/mux/mux.h>
 #include <dt-bindings/mux/ti-serdes.h>
 
@@ -42,7 +43,7 @@
 		#size-cells = <1>;
 		ranges = <0x0 0x0 0x00100000 0x1c000>;
 
-		serdes_ln_ctrl: mux@4080 {
+		serdes_ln_ctrl: mux-controller@4080 {
 			compatible = "mmio-mux";
 			reg = <0x00004080 0x50>;
 			#mux-control-cells = <1>;
@@ -76,7 +77,10 @@
 		#interrupt-cells = <3>;
 		interrupt-controller;
 		reg = <0x00 0x01800000 0x00 0x10000>,	/* GICD */
-		      <0x00 0x01900000 0x00 0x100000>;	/* GICR */
+		      <0x00 0x01900000 0x00 0x100000>,	/* GICR */
+		      <0x00 0x6f000000 0x00 0x2000>,	/* GICC */
+		      <0x00 0x6f010000 0x00 0x1000>,	/* GICH */
+		      <0x00 0x6f020000 0x00 0x2000>;	/* GICV */
 
 		/* vcpumntirq: virtual CPU interface maintenance interrupt */
 		interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
@@ -339,7 +343,7 @@
 			compatible = "inside-secure,safexcel-eip76";
 			reg = <0x0 0x4e10000 0x0 0x7d>;
 			interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
-			clocks = <&k3_clks 264 1>;
+			clocks = <&k3_clks 264 2>;
 		};
 	};
 
@@ -786,6 +790,47 @@
 		#size-cells = <2>;
 	};
 
+	serdes_wiz4: wiz@5050000 {
+		compatible = "ti,am64-wiz-10g";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		power-domains = <&k3_pds 297 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 297 1>, <&k3_clks 297 9>, <&cmn_refclk>;
+		clock-names = "fck", "core_ref_clk", "ext_ref_clk";
+		assigned-clocks = <&k3_clks 297 9>;
+		assigned-clock-parents = <&k3_clks 297 10>;
+		assigned-clock-rates = <19200000>;
+		num-lanes = <4>;
+		#reset-cells = <1>;
+		#clock-cells = <1>;
+		ranges = <0x05050000 0x00 0x05050000 0x010000>,
+			<0x0a030a00 0x00 0x0a030a00 0x40>;
+
+		serdes4: serdes@5050000 {
+			/*
+			 * Note: we also map DPTX PHY registers as the Torrent
+			 * needs to manage those.
+			 */
+			compatible = "ti,j721e-serdes-10g";
+			reg = <0x05050000 0x010000>,
+			      <0x0a030a00 0x40>; /* DPTX PHY */
+			reg-names = "torrent_phy", "dptx_phy";
+
+			resets = <&serdes_wiz4 0>;
+			reset-names = "torrent_reset";
+			clocks = <&serdes_wiz4 TI_WIZ_PLL0_REFCLK>;
+			clock-names = "refclk";
+			assigned-clocks = <&serdes_wiz4 TI_WIZ_PLL0_REFCLK>,
+					  <&serdes_wiz4 TI_WIZ_PLL1_REFCLK>,
+					  <&serdes_wiz4 TI_WIZ_REFCLK_DIG>;
+			assigned-clock-parents = <&k3_clks 297 9>,
+						 <&k3_clks 297 9>,
+						 <&k3_clks 297 9>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+
 	main_uart0: serial@2800000 {
 		compatible = "ti,j721e-uart", "ti,am654-uart";
 		reg = <0x00 0x02800000 0x00 0x100>;
@@ -1264,6 +1309,37 @@
 		};
 	};
 
+	mhdp: dp-bridge@a000000 {
+		compatible = "ti,j721e-mhdp8546";
+		/*
+		 * Note: we do not map DPTX PHY area, as that is handled by
+		 * the PHY driver.
+		 */
+		reg = <0x00 0x0a000000 0x00 0x030a00>, /* DSS_EDP0_V2A_CORE_VP_REGS_APB */
+		      <0x00 0x04f40000 0x00 0x20>;    /* DSS_EDP0_INTG_CFG_VP */
+		reg-names = "mhdptx", "j721e-intg";
+
+		clocks = <&k3_clks 151 36>;
+
+		interrupt-parent = <&gic500>;
+		interrupts = <GIC_SPI 614 IRQ_TYPE_LEVEL_HIGH>;
+
+		power-domains = <&k3_pds 151 TI_SCI_PD_EXCLUSIVE>;
+
+		dp0_ports: ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+			    reg = <0>;
+			};
+
+			port@4 {
+			    reg = <4>;
+			};
+		};
+	};
+
 	dss: dss@4a00000 {
 		compatible = "ti,j721e-dss";
 		reg =
@@ -1314,8 +1390,6 @@
 				  "common_s2";
 
 		dss_ports: ports {
-			#address-cells = <1>;
-			#size-cells = <0>;
 		};
 	};
 
@@ -1940,4 +2014,200 @@
 			bus_freq = <1000000>;
 		};
 	};
+
+	main_mcan0: can@2701000 {
+		compatible = "bosch,m_can";
+		reg = <0x00 0x02701000 0x00 0x200>,
+		      <0x00 0x02708000 0x00 0x8000>;
+		reg-names = "m_can", "message_ram";
+		power-domains = <&k3_pds 156 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 156 0>, <&k3_clks 156 1>;
+		clock-names = "hclk", "cclk";
+		interrupts = <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "int0", "int1";
+		bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
+	};
+
+	main_mcan1: can@2711000 {
+		compatible = "bosch,m_can";
+		reg = <0x00 0x02711000 0x00 0x200>,
+		      <0x00 0x02718000 0x00 0x8000>;
+		reg-names = "m_can", "message_ram";
+		power-domains = <&k3_pds 158 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 158 0>, <&k3_clks 158 1>;
+		clock-names = "hclk", "cclk";
+		interrupts = <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 128 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "int0", "int1";
+		bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
+	};
+
+	main_mcan2: can@2721000 {
+		compatible = "bosch,m_can";
+		reg = <0x00 0x02721000 0x00 0x200>,
+		      <0x00 0x02728000 0x00 0x8000>;
+		reg-names = "m_can", "message_ram";
+		power-domains = <&k3_pds 160 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 160 0>, <&k3_clks 160 1>;
+		clock-names = "hclk", "cclk";
+		interrupts = <GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "int0", "int1";
+		bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
+	};
+
+	main_mcan3: can@2731000 {
+		compatible = "bosch,m_can";
+		reg = <0x00 0x02731000 0x00 0x200>,
+		      <0x00 0x02738000 0x00 0x8000>;
+		reg-names = "m_can", "message_ram";
+		power-domains = <&k3_pds 161 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 161 0>, <&k3_clks 161 1>;
+		clock-names = "hclk", "cclk";
+		interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "int0", "int1";
+		bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
+	};
+
+	main_mcan4: can@2741000 {
+		compatible = "bosch,m_can";
+		reg = <0x00 0x02741000 0x00 0x200>,
+		      <0x00 0x02748000 0x00 0x8000>;
+		reg-names = "m_can", "message_ram";
+		power-domains = <&k3_pds 162 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 162 0>, <&k3_clks 162 1>;
+		clock-names = "hclk", "cclk";
+		interrupts = <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "int0", "int1";
+		bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
+	};
+
+	main_mcan5: can@2751000 {
+		compatible = "bosch,m_can";
+		reg = <0x00 0x02751000 0x00 0x200>,
+		      <0x00 0x02758000 0x00 0x8000>;
+		reg-names = "m_can", "message_ram";
+		power-domains = <&k3_pds 163 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 163 0>, <&k3_clks 163 1>;
+		clock-names = "hclk", "cclk";
+		interrupts = <GIC_SPI 139 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "int0", "int1";
+		bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
+	};
+
+	main_mcan6: can@2761000 {
+		compatible = "bosch,m_can";
+		reg = <0x00 0x02761000 0x00 0x200>,
+		      <0x00 0x02768000 0x00 0x8000>;
+		reg-names = "m_can", "message_ram";
+		power-domains = <&k3_pds 164 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 164 0>, <&k3_clks 164 1>;
+		clock-names = "hclk", "cclk";
+		interrupts = <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "int0", "int1";
+		bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
+	};
+
+	main_mcan7: can@2771000 {
+		compatible = "bosch,m_can";
+		reg = <0x00 0x02771000 0x00 0x200>,
+		      <0x00 0x02778000 0x00 0x8000>;
+		reg-names = "m_can", "message_ram";
+		power-domains = <&k3_pds 165 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 165 0>, <&k3_clks 165 1>;
+		clock-names = "hclk", "cclk";
+		interrupts = <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "int0", "int1";
+		bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
+	};
+
+	main_mcan8: can@2781000 {
+		compatible = "bosch,m_can";
+		reg = <0x00 0x02781000 0x00 0x200>,
+		      <0x00 0x02788000 0x00 0x8000>;
+		reg-names = "m_can", "message_ram";
+		power-domains = <&k3_pds 166 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 166 0>, <&k3_clks 166 1>;
+		clock-names = "hclk", "cclk";
+		interrupts = <GIC_SPI 576 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 577 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "int0", "int1";
+		bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
+	};
+
+	main_mcan9: can@2791000 {
+		compatible = "bosch,m_can";
+		reg = <0x00 0x02791000 0x00 0x200>,
+		      <0x00 0x02798000 0x00 0x8000>;
+		reg-names = "m_can", "message_ram";
+		power-domains = <&k3_pds 167 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 167 0>, <&k3_clks 167 1>;
+		clock-names = "hclk", "cclk";
+		interrupts = <GIC_SPI 579 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 580 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "int0", "int1";
+		bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
+	};
+
+	main_mcan10: can@27a1000 {
+		compatible = "bosch,m_can";
+		reg = <0x00 0x027a1000 0x00 0x200>,
+		      <0x00 0x027a8000 0x00 0x8000>;
+		reg-names = "m_can", "message_ram";
+		power-domains = <&k3_pds 168 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 168 0>, <&k3_clks 168 1>;
+		clock-names = "hclk", "cclk";
+		interrupts = <GIC_SPI 582 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 583 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "int0", "int1";
+		bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
+	};
+
+	main_mcan11: can@27b1000 {
+		compatible = "bosch,m_can";
+		reg = <0x00 0x027b1000 0x00 0x200>,
+		      <0x00 0x027b8000 0x00 0x8000>;
+		reg-names = "m_can", "message_ram";
+		power-domains = <&k3_pds 169 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 169 0>, <&k3_clks 169 1>;
+		clock-names = "hclk", "cclk";
+		interrupts = <GIC_SPI 585 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 586 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "int0", "int1";
+		bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
+	};
+
+	main_mcan12: can@27c1000 {
+		compatible = "bosch,m_can";
+		reg = <0x00 0x027c1000 0x00 0x200>,
+		      <0x00 0x027c8000 0x00 0x8000>;
+		reg-names = "m_can", "message_ram";
+		power-domains = <&k3_pds 170 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 170 0>, <&k3_clks 170 1>;
+		clock-names = "hclk", "cclk";
+		interrupts = <GIC_SPI 588 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 589 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "int0", "int1";
+		bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
+	};
+
+	main_mcan13: can@27d1000 {
+		compatible = "bosch,m_can";
+		reg = <0x00 0x027d1000 0x00 0x200>,
+		      <0x00 0x027d8000 0x00 0x8000>;
+		reg-names = "m_can", "message_ram";
+		power-domains = <&k3_pds 171 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 171 0>, <&k3_clks 171 1>;
+		clock-names = "hclk", "cclk";
+		interrupts = <GIC_SPI 591 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 592 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "int0", "int1";
+		bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
+	};
 };
diff --git a/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
index d2dceda72fe9..df08724bbf1c 100644
--- a/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721e-mcu-wakeup.dtsi
@@ -12,8 +12,8 @@
 
 		mbox-names = "rx", "tx";
 
-		mboxes= <&secure_proxy_main 11>,
-			<&secure_proxy_main 13>;
+		mboxes = <&secure_proxy_main 11>,
+			 <&secure_proxy_main 13>;
 
 		reg-names = "debug_messages";
 		reg = <0x00 0x44083000 0x0 0x1000>;
@@ -390,4 +390,32 @@
 			ti,loczrama = <1>;
 		};
 	};
+
+	mcu_mcan0: can@40528000 {
+		compatible = "bosch,m_can";
+		reg = <0x00 0x40528000 0x00 0x200>,
+		      <0x00 0x40500000 0x00 0x8000>;
+		reg-names = "m_can", "message_ram";
+		power-domains = <&k3_pds 172 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 172 0>, <&k3_clks 172 1>;
+		clock-names = "hclk", "cclk";
+		interrupts = <GIC_SPI 832 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 833 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "int0", "int1";
+		bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
+	};
+
+	mcu_mcan1: can@40568000 {
+		compatible = "bosch,m_can";
+		reg = <0x00 0x40568000 0x00 0x200>,
+		      <0x00 0x40540000 0x00 0x8000>;
+		reg-names = "m_can", "message_ram";
+		power-domains = <&k3_pds 173 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 173 0>, <&k3_clks 173 1>;
+		clock-names = "hclk", "cclk";
+		interrupts = <GIC_SPI 835 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 836 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "int0", "int1";
+		bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
+	};
 };
diff --git a/arch/arm64/boot/dts/ti/k3-j721e-sk.dts b/arch/arm64/boot/dts/ti/k3-j721e-sk.dts
index b726310d867c..80358cba6954 100644
--- a/arch/arm64/boot/dts/ti/k3-j721e-sk.dts
+++ b/arch/arm64/boot/dts/ti/k3-j721e-sk.dts
@@ -213,6 +213,71 @@
 		enable-active-high;
 	};
 
+	dp0: connector {
+		compatible = "dp-connector";
+		label = "DP0";
+		type = "full-size";
+		dp-pwr-supply = <&dp_pwr_3v3>;
+
+		port {
+			dp_connector_in: endpoint {
+				remote-endpoint = <&dp0_out>;
+			};
+		};
+	};
+
+	hdmi-connector {
+		compatible = "hdmi-connector";
+		label = "hdmi";
+		type = "a";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&hdmi_hpd_pins_default>;
+
+		ddc-i2c-bus = <&main_i2c1>;
+
+		/* HDMI_HPD */
+		hpd-gpios = <&main_gpio1 0 GPIO_ACTIVE_HIGH>;
+
+		port {
+			hdmi_connector_in: endpoint {
+				remote-endpoint = <&tfp410_out>;
+			};
+		};
+	};
+
+	dvi-bridge {
+		compatible = "ti,tfp410";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&hdmi_pdn_pins_default>;
+
+		powerdown-gpios = <&main_gpio0 127 GPIO_ACTIVE_LOW>;
+		ti,deskew = <0>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				tfp410_in: endpoint {
+					remote-endpoint = <&dpi1_out>;
+					pclk-sample = <1>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				tfp410_out: endpoint {
+					remote-endpoint =
+						<&hdmi_connector_in>;
+				};
+			};
+		};
+	};
 };
 
 &main_pmx0 {
@@ -317,6 +382,18 @@
 		>;
 	};
 
+	hdmi_hpd_pins_default: hdmi-hpd-pins-default {
+		pinctrl-single,pins = <
+			J721E_IOPAD(0x204, PIN_INPUT, 7) /* (AD5) UART1_RTSn.GPIO1_0 */
+		>;
+	};
+
+	hdmi_pdn_pins_default: hdmi-pdn-pins-default {
+		pinctrl-single,pins = <
+			J721E_IOPAD(0x200, PIN_INPUT, 7) /* (AC4) UART1_CTSn.GPIO0_127 */
+		>;
+	};
+
 	/* Reset for M.2 E Key slot on PCIe0  */
 	ekey_reset_pins_default: ekey-reset-pns-pins-default {
 		pinctrl-single,pins = <
@@ -475,8 +552,6 @@
 		cdns,tchsh-ns = <60>;
 		cdns,tslch-ns = <60>;
 		cdns,read-delay = <4>;
-		#address-cells = <1>;
-		#size-cells = <1>;
 	};
 };
 
@@ -626,6 +701,24 @@
 	};
 };
 
+&serdes4 {
+	torrent_phy_dp: phy@0 {
+		reg = <0>;
+		resets = <&serdes_wiz4 1>;
+		cdns,phy-type = <PHY_TYPE_DP>;
+		cdns,num-lanes = <4>;
+		cdns,max-bit-rate = <5400>;
+		#phy-cells = <0>;
+	};
+};
+
+&mhdp {
+	phys = <&torrent_phy_dp>;
+	phy-names = "dpphy";
+	pinctrl-names = "default";
+	pinctrl-0 = <&dp0_pins_default>;
+};
+
 &usbss0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&main_usbss0_pins_default>;
@@ -704,6 +797,46 @@
 				 <&k3_clks 152 18>;	/* DPI1_EXT_CLKSEL_OUT0 */
 };
 
+&dss_ports {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	port@0  {
+		reg = <0>;
+
+		dpi0_out: endpoint {
+			remote-endpoint = <&dp0_in>;
+		};
+	};
+
+	port@1 {
+		reg = <1>;
+
+		dpi1_out: endpoint {
+			remote-endpoint = <&tfp410_in>;
+		};
+	};
+};
+
+&dp0_ports {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	port@0 {
+		reg = <0>;
+		dp0_in: endpoint {
+			remote-endpoint = <&dpi0_out>;
+		};
+	};
+
+	port@4 {
+		reg = <4>;
+		dp0_out: endpoint {
+			remote-endpoint = <&dp_connector_in>;
+		};
+	};
+};
+
 &mcasp0 {
 	/* Unused */
 	status = "disabled";
@@ -838,10 +971,6 @@
 	status = "disabled";
 };
 
-&dss {
-	status = "disabled";
-};
-
 &icssg0_mdio {
 	status = "disabled";
 };
diff --git a/arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi b/arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi
index 2fee2906183d..e36335232cf8 100644
--- a/arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721e-som-p0.dtsi
@@ -171,7 +171,7 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&mcu_fss0_ospi0_pins_default>;
 
-	flash@0{
+	flash@0 {
 		compatible = "jedec,spi-nor";
 		reg = <0x0>;
 		spi-tx-bus-width = <8>;
@@ -182,8 +182,6 @@
 		cdns,tchsh-ns = <60>;
 		cdns,tslch-ns = <60>;
 		cdns,read-delay = <0>;
-		#address-cells = <1>;
-		#size-cells = <1>;
 	};
 };
 
diff --git a/arch/arm64/boot/dts/ti/k3-j721e.dtsi b/arch/arm64/boot/dts/ti/k3-j721e.dtsi
index 214359e7288b..0e23886c9fd1 100644
--- a/arch/arm64/boot/dts/ti/k3-j721e.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j721e.dtsi
@@ -64,7 +64,7 @@
 			i-cache-sets = <256>;
 			d-cache-size = <0x8000>;
 			d-cache-line-size = <64>;
-			d-cache-sets = <128>;
+			d-cache-sets = <256>;
 			next-level-cache = <&L2_0>;
 		};
 
@@ -78,7 +78,7 @@
 			i-cache-sets = <256>;
 			d-cache-size = <0x8000>;
 			d-cache-line-size = <64>;
-			d-cache-sets = <128>;
+			d-cache-sets = <256>;
 			next-level-cache = <&L2_0>;
 		};
 	};
@@ -88,7 +88,7 @@
 		cache-level = <2>;
 		cache-size = <0x100000>;
 		cache-line-size = <64>;
-		cache-sets = <2048>;
+		cache-sets = <1024>;
 		next-level-cache = <&msmc_l3>;
 	};
 
@@ -139,6 +139,7 @@
 			 <0x00 0x0e000000 0x00 0x0e000000 0x00 0x01800000>, /* PCIe Core*/
 			 <0x00 0x10000000 0x00 0x10000000 0x00 0x10000000>, /* PCIe DAT */
 			 <0x00 0x64800000 0x00 0x64800000 0x00 0x00800000>, /* C71 */
+			 <0x00 0x6f000000 0x00 0x6f000000 0x00 0x00310000>, /* A72 PERIPHBASE */
 			 <0x44 0x00000000 0x44 0x00000000 0x00 0x08000000>, /* PCIe2 DAT */
 			 <0x44 0x10000000 0x44 0x10000000 0x00 0x08000000>, /* PCIe3 DAT */
 			 <0x4d 0x80800000 0x4d 0x80800000 0x00 0x00800000>, /* C66_0 */
diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
new file mode 100644
index 000000000000..b210cc07c539
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-common-proc-board.dts
@@ -0,0 +1,431 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2021 Texas Instruments Incorporated - https://www.ti.com/
+ *
+ * Common Processor Board: https://www.ti.com/tool/J721EXCPXEVM
+ */
+
+/dts-v1/;
+
+#include "k3-j721s2-som-p0.dtsi"
+#include <dt-bindings/net/ti-dp83867.h>
+
+/ {
+	compatible = "ti,j721s2-evm", "ti,j721s2";
+	model = "Texas Instruments J721S2 EVM";
+
+	chosen {
+		stdout-path = "serial2:115200n8";
+		bootargs = "console=ttyS2,115200n8 earlycon=ns16550a,mmio32,2880000";
+	};
+
+	aliases {
+		serial1 = &mcu_uart0;
+		serial2 = &main_uart8;
+		mmc0 = &main_sdhci0;
+		mmc1 = &main_sdhci1;
+		can0 = &main_mcan16;
+		can1 = &mcu_mcan0;
+		can2 = &mcu_mcan1;
+	};
+
+	evm_12v0: fixedregulator-evm12v0 {
+		/* main supply */
+		compatible = "regulator-fixed";
+		regulator-name = "evm_12v0";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vsys_3v3: fixedregulator-vsys3v3 {
+		/* Output of LM5140 */
+		compatible = "regulator-fixed";
+		regulator-name = "vsys_3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&evm_12v0>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vsys_5v0: fixedregulator-vsys5v0 {
+		/* Output of LM5140 */
+		compatible = "regulator-fixed";
+		regulator-name = "vsys_5v0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&evm_12v0>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	vdd_mmc1: fixedregulator-sd {
+		/* Output of TPS22918 */
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_mmc1";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		enable-active-high;
+		vin-supply = <&vsys_3v3>;
+		gpio = <&exp2 2 GPIO_ACTIVE_HIGH>;
+	};
+
+	vdd_sd_dv: gpio-regulator-TLV71033 {
+		/* Output of TLV71033 */
+		compatible = "regulator-gpio";
+		regulator-name = "tlv71033";
+		pinctrl-names = "default";
+		pinctrl-0 = <&vdd_sd_dv_pins_default>;
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		vin-supply = <&vsys_5v0>;
+		gpios = <&main_gpio0 8 GPIO_ACTIVE_HIGH>;
+		states = <1800000 0x0>,
+			 <3300000 0x1>;
+	};
+
+	transceiver1: can-phy1 {
+		compatible = "ti,tcan1043";
+		#phy-cells = <0>;
+		max-bitrate = <5000000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&mcu_mcan0_gpio_pins_default>;
+		standby-gpios = <&wkup_gpio0 69 GPIO_ACTIVE_LOW>;
+		enable-gpios = <&wkup_gpio0 0 GPIO_ACTIVE_HIGH>;
+	};
+
+	transceiver2: can-phy2 {
+		compatible = "ti,tcan1042";
+		#phy-cells = <0>;
+		max-bitrate = <5000000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&mcu_mcan1_gpio_pins_default>;
+		standby-gpios = <&wkup_gpio0 2 GPIO_ACTIVE_HIGH>;
+	};
+
+};
+
+&main_pmx0 {
+	main_uart8_pins_default: main-uart8-pins-default {
+		pinctrl-single,pins = <
+			J721S2_IOPAD(0x040, PIN_INPUT, 14) /* (AC28) MCASP0_AXR0.UART8_CTSn */
+			J721S2_IOPAD(0x044, PIN_OUTPUT, 14) /* (Y26) MCASP0_AXR1.UART8_RTSn */
+			J721S2_IOPAD(0x0d0, PIN_INPUT, 11) /* (AF26) SPI0_CS1.UART8_RXD */
+			J721S2_IOPAD(0x0d4, PIN_OUTPUT, 11) /* (AH27) SPI0_CLK.UART8_TXD */
+		>;
+	};
+
+	main_i2c3_pins_default: main-i2c3-pins-default {
+		pinctrl-single,pins = <
+			J721S2_IOPAD(0x064, PIN_INPUT_PULLUP, 13) /* (W28) MCAN0_TX.I2C3_SCL */
+			J721S2_IOPAD(0x060, PIN_INPUT_PULLUP, 13) /* (AC27) MCASP2_AXR1.I2C3_SDA */
+		>;
+	};
+
+	main_mmc1_pins_default: main-mmc1-pins-default {
+		pinctrl-single,pins = <
+			J721S2_IOPAD(0x104, PIN_INPUT, 0) /* (P23) MMC1_CLK */
+			J721S2_IOPAD(0x108, PIN_INPUT, 0) /* (N24) MMC1_CMD */
+			J721S2_IOPAD(0x100, PIN_INPUT, 0) /* (###) MMC1_CLKLB */
+			J721S2_IOPAD(0x0fc, PIN_INPUT, 0) /* (M23) MMC1_DAT0 */
+			J721S2_IOPAD(0x0f8, PIN_INPUT, 0) /* (P24) MMC1_DAT1 */
+			J721S2_IOPAD(0x0f4, PIN_INPUT, 0) /* (R24) MMC1_DAT2 */
+			J721S2_IOPAD(0x0f0, PIN_INPUT, 0) /* (R22) MMC1_DAT3 */
+			J721S2_IOPAD(0x0e8, PIN_INPUT, 8) /* (AE25) TIMER_IO0.MMC1_SDCD */
+		>;
+	};
+
+	vdd_sd_dv_pins_default: vdd-sd-dv-pins-default {
+		pinctrl-single,pins = <
+			J721S2_IOPAD(0x020, PIN_INPUT, 7) /* (AA23) MCAN15_RX.GPIO0_8 */
+		>;
+	};
+};
+
+&wkup_pmx0 {
+	mcu_cpsw_pins_default: mcu-cpsw-pins-default {
+		pinctrl-single,pins = <
+			J721S2_WKUP_IOPAD(0x094, PIN_INPUT, 0) /* (B22) MCU_RGMII1_RD0 */
+			J721S2_WKUP_IOPAD(0x090, PIN_INPUT, 0) /* (B21) MCU_RGMII1_RD1 */
+			J721S2_WKUP_IOPAD(0x08c, PIN_INPUT, 0) /* (C22) MCU_RGMII1_RD2 */
+			J721S2_WKUP_IOPAD(0x088, PIN_INPUT, 0) /* (D23) MCU_RGMII1_RD3 */
+			J721S2_WKUP_IOPAD(0x084, PIN_INPUT, 0) /* (D22) MCU_RGMII1_RXC */
+			J721S2_WKUP_IOPAD(0x06c, PIN_INPUT, 0) /* (E23) MCU_RGMII1_RX_CTL */
+			J721S2_WKUP_IOPAD(0x07c, PIN_OUTPUT, 0) /* (F23) MCU_RGMII1_TD0 */
+			J721S2_WKUP_IOPAD(0x078, PIN_OUTPUT, 0) /* (G22) MCU_RGMII1_TD1 */
+			J721S2_WKUP_IOPAD(0x074, PIN_OUTPUT, 0) /* (E21) MCU_RGMII1_TD2 */
+			J721S2_WKUP_IOPAD(0x070, PIN_OUTPUT, 0) /* (E22) MCU_RGMII1_TD3 */
+			J721S2_WKUP_IOPAD(0x080, PIN_OUTPUT, 0) /* (F21) MCU_RGMII1_TXC */
+			J721S2_WKUP_IOPAD(0x068, PIN_OUTPUT, 0) /* (F22) MCU_RGMII1_TX_CTL */
+		>;
+	};
+
+	mcu_mdio_pins_default: mcu-mdio-pins-default {
+		pinctrl-single,pins = <
+			J721S2_WKUP_IOPAD(0x09c, PIN_OUTPUT, 0) /* (A21) MCU_MDIO0_MDC */
+			J721S2_WKUP_IOPAD(0x098, PIN_INPUT, 0) /* (A22) MCU_MDIO0_MDIO */
+		>;
+	};
+
+	mcu_mcan0_pins_default: mcu-mcan0-pins-default {
+		pinctrl-single,pins = <
+			J721S2_WKUP_IOPAD(0x0bc, PIN_INPUT, 0) /* (E28) MCU_MCAN0_RX */
+			J721S2_WKUP_IOPAD(0x0b8, PIN_OUTPUT, 0) /* (E27) MCU_MCAN0_TX */
+		>;
+	};
+
+	mcu_mcan1_pins_default: mcu-mcan1-pins-default {
+		pinctrl-single,pins = <
+			J721S2_WKUP_IOPAD(0x0d4, PIN_INPUT, 0) /* (F26) WKUP_GPIO0_5.MCU_MCAN1_RX */
+			J721S2_WKUP_IOPAD(0x0d0, PIN_OUTPUT, 0) /* (C23) WKUP_GPIO0_4.MCU_MCAN1_TX */
+		>;
+	};
+
+	mcu_mcan0_gpio_pins_default: mcu-mcan0-gpio-pins-default {
+		pinctrl-single,pins = <
+			J721S2_WKUP_IOPAD(0x0c0, PIN_INPUT, 7) /* (D26) WKUP_GPIO0_0 */
+			J721S2_WKUP_IOPAD(0x0a8, PIN_INPUT, 7) /* (B25) MCU_SPI0_D1.WKUP_GPIO0_69 */
+		>;
+	};
+
+	mcu_mcan1_gpio_pins_default: mcu-mcan1-gpio-pins-default {
+		pinctrl-single,pins = <
+			J721S2_WKUP_IOPAD(0x0c8, PIN_INPUT, 7) /* (C28) WKUP_GPIO0_2 */
+		>;
+	};
+};
+
+&main_gpio2 {
+	status = "disabled";
+};
+
+&main_gpio4 {
+	status = "disabled";
+};
+
+&main_gpio6 {
+	status = "disabled";
+};
+
+&wkup_gpio1 {
+	status = "disabled";
+};
+
+&wkup_uart0 {
+	status = "reserved";
+};
+
+&main_uart0 {
+	status = "disabled";
+};
+
+&main_uart1 {
+	status = "disabled";
+};
+
+&main_uart2 {
+	status = "disabled";
+};
+
+&main_uart3 {
+	status = "disabled";
+};
+
+&main_uart4 {
+	status = "disabled";
+};
+
+&main_uart5 {
+	status = "disabled";
+};
+
+&main_uart6 {
+	status = "disabled";
+};
+
+&main_uart7 {
+	status = "disabled";
+};
+
+&main_uart8 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_uart8_pins_default>;
+	/* Shared with TFA on this platform */
+	power-domains = <&k3_pds 357 TI_SCI_PD_SHARED>;
+};
+
+&main_uart9 {
+	status = "disabled";
+};
+
+&main_i2c0 {
+	clock-frequency = <400000>;
+
+	exp1: gpio@20 {
+		compatible = "ti,tca6416";
+		reg = <0x20>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names = "PCIE_2L_MODE_SEL", "PCIE_2L_PERSTZ", "PCIE_2L_RC_RSTZ",
+				  "PCIE_2L_EP_RST_EN", "PCIE_1L_MODE_SEL", "PCIE_1L_PERSTZ",
+				  "PCIE_1L_RC_RSTZ", "PCIE_1L_EP_RST_EN", "PCIE_2L_PRSNT#",
+				  "PCIE_1L_PRSNT#", "CDCI1_OE1/OE4", "CDCI1_OE2/OE3", "EXP_MUX1",
+				  "EXP_MUX2", "EXP_MUX3", "GESI_EXP_PHY_RSTz";
+	};
+
+	exp2: gpio@22 {
+		compatible = "ti,tca6424";
+		reg = <0x22>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names = "APPLE_AUTH_RSTZ", "MLB_RSTZ", "GPIO_USD_PWR_EN", "USBC_PWR_EN",
+				  "USBC_MODE_SEL1", "USBC_MODE_SEL0", "MCAN0_EN", "MCAN0_STB#",
+				  "MUX_SPAREMUX_SPARE", "MCASP/TRACE_MUX_S0", "MCASP/TRACE_MUX_S1",
+				  "MLB_MUX_SEL", "MCAN_MUX_SEL", "MCASP2/SPI3_MUX_SEL", "PCIe_CLKREQn_MUX_SEL",
+				  "CDCI2_RSTZ", "ENET_EXP_PWRDN", "ENET_EXP_RESETZ", "ENET_I2CMUX_SEL",
+				  "ENET_EXP_SPARE2", "M2PCIE_RTSZ", "USER_INPUT1", "USER_LED1", "USER_LED2";
+	};
+};
+
+&main_i2c1 {
+	status = "disabled";
+};
+
+&main_i2c2 {
+	status = "disabled";
+};
+
+&main_i2c3 {
+	status = "disabled";
+};
+
+&main_i2c4 {
+	status = "disabled";
+};
+
+&main_i2c5 {
+	status = "disabled";
+};
+
+&main_i2c6 {
+	status = "disabled";
+};
+
+&main_sdhci0 {
+	/* eMMC */
+	non-removable;
+	ti,driver-strength-ohm = <50>;
+	disable-wp;
+};
+
+&main_sdhci1 {
+	/* SD card */
+	pinctrl-0 = <&main_mmc1_pins_default>;
+	pinctrl-names = "default";
+	disable-wp;
+	vmmc-supply = <&vdd_mmc1>;
+	vqmmc-supply = <&vdd_sd_dv>;
+};
+
+&mcu_cpsw {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcu_cpsw_pins_default &mcu_mdio_pins_default>;
+};
+
+&davinci_mdio {
+	phy0: ethernet-phy@0 {
+		reg = <0>;
+		ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+		ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+		ti,min-output-impedance;
+	};
+};
+
+&cpsw_port1 {
+	phy-mode = "rgmii-rxid";
+	phy-handle = <&phy0>;
+};
+
+&mcu_mcan0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcu_mcan0_pins_default>;
+	phys = <&transceiver1>;
+};
+
+&mcu_mcan1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcu_mcan1_pins_default>;
+	phys = <&transceiver2>;
+};
+
+&main_mcan0 {
+	status = "disabled";
+};
+
+&main_mcan1 {
+	status = "disabled";
+};
+
+&main_mcan2 {
+	status = "disabled";
+};
+
+&main_mcan3 {
+	status = "disabled";
+};
+
+&main_mcan4 {
+	status = "disabled";
+};
+
+&main_mcan5 {
+	status = "disabled";
+};
+
+&main_mcan6 {
+	status = "disabled";
+};
+
+&main_mcan7 {
+	status = "disabled";
+};
+
+&main_mcan8 {
+	status = "disabled";
+};
+
+&main_mcan9 {
+	status = "disabled";
+};
+
+&main_mcan10 {
+	status = "disabled";
+};
+
+&main_mcan11 {
+	status = "disabled";
+};
+
+&main_mcan12 {
+	status = "disabled";
+};
+
+&main_mcan13 {
+	status = "disabled";
+};
+
+&main_mcan14 {
+	status = "disabled";
+};
+
+&main_mcan15 {
+	status = "disabled";
+};
+
+&main_mcan17 {
+	status = "disabled";
+};
diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi b/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
new file mode 100644
index 000000000000..34e7d577ae13
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi
@@ -0,0 +1,940 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device Tree Source for J721S2 SoC Family Main Domain peripherals
+ *
+ * Copyright (C) 2021 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+&cbass_main {
+	msmc_ram: sram@70000000 {
+		compatible = "mmio-sram";
+		reg = <0x0 0x70000000 0x0 0x400000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x0 0x70000000 0x400000>;
+
+		atf-sram@0 {
+			reg = <0x0 0x20000>;
+		};
+
+		tifs-sram@1f0000 {
+			reg = <0x1f0000 0x10000>;
+		};
+
+		l3cache-sram@200000 {
+			reg = <0x200000 0x200000>;
+		};
+	};
+
+	gic500: interrupt-controller@1800000 {
+		compatible = "arm,gic-v3";
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+		#interrupt-cells = <3>;
+		interrupt-controller;
+		reg = <0x00 0x01800000 0x00 0x100000>, /* GICD */
+		      <0x00 0x01900000 0x00 0x100000>, /* GICR */
+		      <0x00 0x6f000000 0x00 0x2000>,   /* GICC */
+		      <0x00 0x6f010000 0x00 0x1000>,   /* GICH */
+		      <0x00 0x6f020000 0x00 0x2000>;   /* GICV */
+
+		/* vcpumntirq: virtual CPU interface maintenance interrupt */
+		interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
+
+		gic_its: msi-controller@1820000 {
+			compatible = "arm,gic-v3-its";
+			reg = <0x00 0x01820000 0x00 0x10000>;
+			socionext,synquacer-pre-its = <0x1000000 0x400000>;
+			msi-controller;
+			#msi-cells = <1>;
+		};
+	};
+
+	main_gpio_intr: interrupt-controller@a00000 {
+		compatible = "ti,sci-intr";
+		reg = <0x00 0x00a00000 0x00 0x800>;
+		ti,intr-trigger-type = <1>;
+		interrupt-controller;
+		interrupt-parent = <&gic500>;
+		#interrupt-cells = <1>;
+		ti,sci = <&sms>;
+		ti,sci-dev-id = <148>;
+		ti,interrupt-ranges = <8 360 56>;
+	};
+
+	main_pmx0: pinctrl@11c000 {
+		compatible = "pinctrl-single";
+		/* Proxy 0 addressing */
+		reg = <0x0 0x11c000 0x0 0x120>;
+		#pinctrl-cells = <1>;
+		pinctrl-single,register-width = <32>;
+		pinctrl-single,function-mask = <0xffffffff>;
+	};
+
+	main_uart0: serial@2800000 {
+		compatible = "ti,j721e-uart", "ti,am654-uart";
+		reg = <0x00 0x02800000 0x00 0x200>;
+		interrupts = <GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>;
+		current-speed = <115200>;
+		clocks = <&k3_clks 146 3>;
+		clock-names = "fclk";
+		power-domains = <&k3_pds 146 TI_SCI_PD_EXCLUSIVE>;
+	};
+
+	main_uart1: serial@2810000 {
+		compatible = "ti,j721e-uart", "ti,am654-uart";
+		reg = <0x00 0x02810000 0x00 0x200>;
+		interrupts = <GIC_SPI 193 IRQ_TYPE_LEVEL_HIGH>;
+		current-speed = <115200>;
+		clocks = <&k3_clks 350 3>;
+		clock-names = "fclk";
+		power-domains = <&k3_pds 350 TI_SCI_PD_EXCLUSIVE>;
+	};
+
+	main_uart2: serial@2820000 {
+		compatible = "ti,j721e-uart", "ti,am654-uart";
+		reg = <0x00 0x02820000 0x00 0x200>;
+		interrupts = <GIC_SPI 194 IRQ_TYPE_LEVEL_HIGH>;
+		current-speed = <115200>;
+		clocks = <&k3_clks 351 3>;
+		clock-names = "fclk";
+		power-domains = <&k3_pds 351 TI_SCI_PD_EXCLUSIVE>;
+	};
+
+	main_uart3: serial@2830000 {
+		compatible = "ti,j721e-uart", "ti,am654-uart";
+		reg = <0x00 0x02830000 0x00 0x200>;
+		interrupts = <GIC_SPI 195 IRQ_TYPE_LEVEL_HIGH>;
+		current-speed = <115200>;
+		clocks = <&k3_clks 352 3>;
+		clock-names = "fclk";
+		power-domains = <&k3_pds 352 TI_SCI_PD_EXCLUSIVE>;
+	};
+
+	main_uart4: serial@2840000 {
+		compatible = "ti,j721e-uart", "ti,am654-uart";
+		reg = <0x00 0x02840000 0x00 0x200>;
+		interrupts = <GIC_SPI 196 IRQ_TYPE_LEVEL_HIGH>;
+		current-speed = <115200>;
+		clocks = <&k3_clks 353 3>;
+		clock-names = "fclk";
+		power-domains = <&k3_pds 353 TI_SCI_PD_EXCLUSIVE>;
+	};
+
+	main_uart5: serial@2850000 {
+		compatible = "ti,j721e-uart", "ti,am654-uart";
+		reg = <0x00 0x02850000 0x00 0x200>;
+		interrupts = <GIC_SPI 197 IRQ_TYPE_LEVEL_HIGH>;
+		current-speed = <115200>;
+		clocks = <&k3_clks 354 3>;
+		clock-names = "fclk";
+		power-domains = <&k3_pds 354 TI_SCI_PD_EXCLUSIVE>;
+	};
+
+	main_uart6: serial@2860000 {
+		compatible = "ti,j721e-uart", "ti,am654-uart";
+		reg = <0x00 0x02860000 0x00 0x200>;
+		interrupts = <GIC_SPI 198 IRQ_TYPE_LEVEL_HIGH>;
+		current-speed = <115200>;
+		clocks = <&k3_clks 355 3>;
+		clock-names = "fclk";
+		power-domains = <&k3_pds 355 TI_SCI_PD_EXCLUSIVE>;
+	};
+
+	main_uart7: serial@2870000 {
+		compatible = "ti,j721e-uart", "ti,am654-uart";
+		reg = <0x00 0x02870000 0x00 0x200>;
+		interrupts = <GIC_SPI 199 IRQ_TYPE_LEVEL_HIGH>;
+		current-speed = <115200>;
+		clocks = <&k3_clks 356 3>;
+		clock-names = "fclk";
+		power-domains = <&k3_pds 356 TI_SCI_PD_EXCLUSIVE>;
+	};
+
+	main_uart8: serial@2880000 {
+		compatible = "ti,j721e-uart", "ti,am654-uart";
+		reg = <0x00 0x02880000 0x00 0x200>;
+		interrupts = <GIC_SPI 248 IRQ_TYPE_LEVEL_HIGH>;
+		current-speed = <115200>;
+		clocks = <&k3_clks 357 3>;
+		clock-names = "fclk";
+		power-domains = <&k3_pds 357 TI_SCI_PD_EXCLUSIVE>;
+	};
+
+	main_uart9: serial@2890000 {
+		compatible = "ti,j721e-uart", "ti,am654-uart";
+		reg = <0x00 0x02890000 0x00 0x200>;
+		interrupts = <GIC_SPI 249 IRQ_TYPE_LEVEL_HIGH>;
+		current-speed = <115200>;
+		clocks = <&k3_clks 358 3>;
+		clock-names = "fclk";
+		power-domains = <&k3_pds 358 TI_SCI_PD_EXCLUSIVE>;
+	};
+
+	main_gpio0: gpio@600000 {
+		compatible = "ti,j721e-gpio", "ti,keystone-gpio";
+		reg = <0x00 0x00600000 0x00 0x100>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-parent = <&main_gpio_intr>;
+		interrupts = <145>, <146>, <147>, <148>, <149>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		ti,ngpio = <66>;
+		ti,davinci-gpio-unbanked = <0>;
+		power-domains = <&k3_pds 111 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 111 0>;
+		clock-names = "gpio";
+	};
+
+	main_gpio2: gpio@610000 {
+		compatible = "ti,j721e-gpio", "ti,keystone-gpio";
+		reg = <0x00 0x00610000 0x00 0x100>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-parent = <&main_gpio_intr>;
+		interrupts = <154>, <155>, <156>, <157>, <158>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		ti,ngpio = <66>;
+		ti,davinci-gpio-unbanked = <0>;
+		power-domains = <&k3_pds 112 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 112 0>;
+		clock-names = "gpio";
+	};
+
+	main_gpio4: gpio@620000 {
+		compatible = "ti,j721e-gpio", "ti,keystone-gpio";
+		reg = <0x00 0x00620000 0x00 0x100>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-parent = <&main_gpio_intr>;
+		interrupts = <163>, <164>, <165>, <166>, <167>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		ti,ngpio = <66>;
+		ti,davinci-gpio-unbanked = <0>;
+		power-domains = <&k3_pds 113 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 113 0>;
+		clock-names = "gpio";
+	};
+
+	main_gpio6: gpio@630000 {
+		compatible = "ti,j721e-gpio", "ti,keystone-gpio";
+		reg = <0x00 0x00630000 0x00 0x100>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-parent = <&main_gpio_intr>;
+		interrupts = <172>, <173>, <174>, <175>, <176>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		ti,ngpio = <66>;
+		ti,davinci-gpio-unbanked = <0>;
+		power-domains = <&k3_pds 114 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 114 0>;
+		clock-names = "gpio";
+	};
+
+	main_i2c0: i2c@2000000 {
+		compatible = "ti,j721e-i2c", "ti,omap4-i2c";
+		reg = <0x00 0x02000000 0x00 0x100>;
+		interrupts = <GIC_SPI 200 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		clocks = <&k3_clks 214 1>;
+		clock-names = "fck";
+		power-domains = <&k3_pds 214 TI_SCI_PD_EXCLUSIVE>;
+	};
+
+	main_i2c1: i2c@2010000 {
+		compatible = "ti,j721e-i2c", "ti,omap4-i2c";
+		reg = <0x00 0x02010000 0x00 0x100>;
+		interrupts = <GIC_SPI 201 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		clocks = <&k3_clks 215 1>;
+		clock-names = "fck";
+		power-domains = <&k3_pds 215 TI_SCI_PD_EXCLUSIVE>;
+	};
+
+	main_i2c2: i2c@2020000 {
+		compatible = "ti,j721e-i2c", "ti,omap4-i2c";
+		reg = <0x00 0x02020000 0x00 0x100>;
+		interrupts = <GIC_SPI 202 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		clocks = <&k3_clks 216 1>;
+		clock-names = "fck";
+		power-domains = <&k3_pds 216 TI_SCI_PD_EXCLUSIVE>;
+	};
+
+	main_i2c3: i2c@2030000 {
+		compatible = "ti,j721e-i2c", "ti,omap4-i2c";
+		reg = <0x00 0x02030000 0x00 0x100>;
+		interrupts = <GIC_SPI 203 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		clocks = <&k3_clks 217 1>;
+		clock-names = "fck";
+		power-domains = <&k3_pds 217 TI_SCI_PD_EXCLUSIVE>;
+	};
+
+	main_i2c4: i2c@2040000 {
+		compatible = "ti,j721e-i2c", "ti,omap4-i2c";
+		reg = <0x00 0x02040000 0x00 0x100>;
+		interrupts = <GIC_SPI 204 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		clocks = <&k3_clks 218 1>;
+		clock-names = "fck";
+		power-domains = <&k3_pds 218 TI_SCI_PD_EXCLUSIVE>;
+	};
+
+	main_i2c5: i2c@2050000 {
+		compatible = "ti,j721e-i2c", "ti,omap4-i2c";
+		reg = <0x00 0x02050000 0x00 0x100>;
+		interrupts = <GIC_SPI 205 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		clocks = <&k3_clks 219 1>;
+		clock-names = "fck";
+		power-domains = <&k3_pds 219 TI_SCI_PD_EXCLUSIVE>;
+	};
+
+	main_i2c6: i2c@2060000 {
+		compatible = "ti,j721e-i2c", "ti,omap4-i2c";
+		reg = <0x00 0x02060000 0x00 0x100>;
+		interrupts = <GIC_SPI 206 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		clocks = <&k3_clks 220 1>;
+		clock-names = "fck";
+		power-domains = <&k3_pds 220 TI_SCI_PD_EXCLUSIVE>;
+	};
+
+	main_sdhci0: mmc@4f80000 {
+		compatible = "ti,j721e-sdhci-8bit";
+		reg = <0x00 0x04f80000 0x00 0x1000>,
+		      <0x00 0x04f88000 0x00 0x400>;
+		interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
+		power-domains = <&k3_pds 98 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 98 7>, <&k3_clks 98 1>;
+		clock-names = "clk_ahb", "clk_xin";
+		assigned-clocks = <&k3_clks 98 1>;
+		assigned-clock-parents = <&k3_clks 98 2>;
+		bus-width = <8>;
+		ti,otap-del-sel-legacy = <0x0>;
+		ti,otap-del-sel-mmc-hs = <0x0>;
+		ti,otap-del-sel-ddr52 = <0x6>;
+		ti,otap-del-sel-hs200 = <0x8>;
+		ti,otap-del-sel-hs400 = <0x5>;
+		ti,itap-del-sel-legacy = <0x10>;
+		ti,itap-del-sel-mmc-hs = <0xa>;
+		ti,strobe-sel = <0x77>;
+		ti,clkbuf-sel = <0x7>;
+		ti,trm-icp = <0x8>;
+		mmc-ddr-1_8v;
+		mmc-hs200-1_8v;
+		mmc-hs400-1_8v;
+		dma-coherent;
+	};
+
+	main_sdhci1: mmc@4fb0000 {
+		compatible = "ti,j721e-sdhci-4bit";
+		reg = <0x00 0x04fb0000 0x00 0x1000>,
+		      <0x00 0x04fb8000 0x00 0x400>;
+		interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
+		power-domains = <&k3_pds 99 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 99 8>, <&k3_clks 99 1>;
+		clock-names = "clk_ahb", "clk_xin";
+		assigned-clocks = <&k3_clks 99 1>;
+		assigned-clock-parents = <&k3_clks 99 2>;
+		bus-width = <4>;
+		ti,otap-del-sel-legacy = <0x0>;
+		ti,otap-del-sel-sd-hs = <0x0>;
+		ti,otap-del-sel-sdr12 = <0xf>;
+		ti,otap-del-sel-sdr25 = <0xf>;
+		ti,otap-del-sel-sdr50 = <0xc>;
+		ti,otap-del-sel-sdr104 = <0x5>;
+		ti,otap-del-sel-ddr50 = <0xc>;
+		ti,itap-del-sel-legacy = <0x0>;
+		ti,itap-del-sel-sd-hs = <0x0>;
+		ti,itap-del-sel-sdr12 = <0x0>;
+		ti,itap-del-sel-sdr25 = <0x0>;
+		ti,clkbuf-sel = <0x7>;
+		ti,trm-icp = <0x8>;
+		dma-coherent;
+		/* Masking support for SDR104 capability */
+		sdhci-caps-mask = <0x00000003 0x00000000>;
+	};
+
+	main_navss: bus@30000000 {
+		compatible = "simple-mfd";
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges = <0x00 0x30000000 0x00 0x30000000 0x00 0x0c400000>;
+		ti,sci-dev-id = <224>;
+		dma-coherent;
+		dma-ranges;
+
+		main_navss_intr: interrupt-controller@310e0000 {
+			compatible = "ti,sci-intr";
+			reg = <0x00 0x310e0000 0x00 0x4000>;
+			ti,intr-trigger-type = <4>;
+			interrupt-controller;
+			interrupt-parent = <&gic500>;
+			#interrupt-cells = <1>;
+			ti,sci = <&sms>;
+			ti,sci-dev-id = <227>;
+			ti,interrupt-ranges = <0 64 64>,
+					      <64 448 64>,
+					      <128 672 64>;
+		};
+
+		main_udmass_inta: msi-controller@33d00000 {
+			compatible = "ti,sci-inta";
+			reg = <0x00 0x33d00000 0x00 0x100000>;
+			interrupt-controller;
+			#interrupt-cells = <0>;
+			interrupt-parent = <&main_navss_intr>;
+			msi-controller;
+			ti,sci = <&sms>;
+			ti,sci-dev-id = <265>;
+			ti,interrupt-ranges = <0 0 256>;
+		};
+
+		secure_proxy_main: mailbox@32c00000 {
+			compatible = "ti,am654-secure-proxy";
+			#mbox-cells = <1>;
+			reg-names = "target_data", "rt", "scfg";
+			reg = <0x00 0x32c00000 0x00 0x100000>,
+			      <0x00 0x32400000 0x00 0x100000>,
+			      <0x00 0x32800000 0x00 0x100000>;
+			interrupt-names = "rx_011";
+			interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		hwspinlock: spinlock@30e00000 {
+			compatible = "ti,am654-hwspinlock";
+			reg = <0x00 0x30e00000 0x00 0x1000>;
+			#hwlock-cells = <1>;
+		};
+
+		mailbox0_cluster0: mailbox@31f80000 {
+			compatible = "ti,am654-mailbox";
+			reg = <0x00 0x31f80000 0x00 0x200>;
+			#mbox-cells = <1>;
+			ti,mbox-num-users = <4>;
+			ti,mbox-num-fifos = <16>;
+			interrupt-parent = <&main_navss_intr>;
+		};
+
+		mailbox0_cluster1: mailbox@31f81000 {
+			compatible = "ti,am654-mailbox";
+			reg = <0x00 0x31f81000 0x00 0x200>;
+			#mbox-cells = <1>;
+			ti,mbox-num-users = <4>;
+			ti,mbox-num-fifos = <16>;
+			interrupt-parent = <&main_navss_intr>;
+		};
+
+		mailbox0_cluster2: mailbox@31f82000 {
+			compatible = "ti,am654-mailbox";
+			reg = <0x00 0x31f82000 0x00 0x200>;
+			#mbox-cells = <1>;
+			ti,mbox-num-users = <4>;
+			ti,mbox-num-fifos = <16>;
+			interrupt-parent = <&main_navss_intr>;
+		};
+
+		mailbox0_cluster3: mailbox@31f83000 {
+			compatible = "ti,am654-mailbox";
+			reg = <0x00 0x31f83000 0x00 0x200>;
+			#mbox-cells = <1>;
+			ti,mbox-num-users = <4>;
+			ti,mbox-num-fifos = <16>;
+			interrupt-parent = <&main_navss_intr>;
+		};
+
+		mailbox0_cluster4: mailbox@31f84000 {
+			compatible = "ti,am654-mailbox";
+			reg = <0x00 0x31f84000 0x00 0x200>;
+			#mbox-cells = <1>;
+			ti,mbox-num-users = <4>;
+			ti,mbox-num-fifos = <16>;
+			interrupt-parent = <&main_navss_intr>;
+		};
+
+		mailbox0_cluster5: mailbox@31f85000 {
+			compatible = "ti,am654-mailbox";
+			reg = <0x00 0x31f85000 0x00 0x200>;
+			#mbox-cells = <1>;
+			ti,mbox-num-users = <4>;
+			ti,mbox-num-fifos = <16>;
+			interrupt-parent = <&main_navss_intr>;
+		};
+
+		mailbox0_cluster6: mailbox@31f86000 {
+			compatible = "ti,am654-mailbox";
+			reg = <0x00 0x31f86000 0x00 0x200>;
+			#mbox-cells = <1>;
+			ti,mbox-num-users = <4>;
+			ti,mbox-num-fifos = <16>;
+			interrupt-parent = <&main_navss_intr>;
+		};
+
+		mailbox0_cluster7: mailbox@31f87000 {
+			compatible = "ti,am654-mailbox";
+			reg = <0x00 0x31f87000 0x00 0x200>;
+			#mbox-cells = <1>;
+			ti,mbox-num-users = <4>;
+			ti,mbox-num-fifos = <16>;
+			interrupt-parent = <&main_navss_intr>;
+		};
+
+		mailbox0_cluster8: mailbox@31f88000 {
+			compatible = "ti,am654-mailbox";
+			reg = <0x00 0x31f88000 0x00 0x200>;
+			#mbox-cells = <1>;
+			ti,mbox-num-users = <4>;
+			ti,mbox-num-fifos = <16>;
+			interrupt-parent = <&main_navss_intr>;
+		};
+
+		mailbox0_cluster9: mailbox@31f89000 {
+			compatible = "ti,am654-mailbox";
+			reg = <0x00 0x31f89000 0x00 0x200>;
+			#mbox-cells = <1>;
+			ti,mbox-num-users = <4>;
+			ti,mbox-num-fifos = <16>;
+			interrupt-parent = <&main_navss_intr>;
+		};
+
+		mailbox0_cluster10: mailbox@31f8a000 {
+			compatible = "ti,am654-mailbox";
+			reg = <0x00 0x31f8a000 0x00 0x200>;
+			#mbox-cells = <1>;
+			ti,mbox-num-users = <4>;
+			ti,mbox-num-fifos = <16>;
+			interrupt-parent = <&main_navss_intr>;
+		};
+
+		mailbox0_cluster11: mailbox@31f8b000 {
+			compatible = "ti,am654-mailbox";
+			reg = <0x00 0x31f8b000 0x00 0x200>;
+			#mbox-cells = <1>;
+			ti,mbox-num-users = <4>;
+			ti,mbox-num-fifos = <16>;
+			interrupt-parent = <&main_navss_intr>;
+		};
+
+		mailbox1_cluster0: mailbox@31f90000 {
+			compatible = "ti,am654-mailbox";
+			reg = <0x00 0x31f90000 0x00 0x200>;
+			#mbox-cells = <1>;
+			ti,mbox-num-users = <4>;
+			ti,mbox-num-fifos = <16>;
+			interrupt-parent = <&main_navss_intr>;
+		};
+
+		mailbox1_cluster1: mailbox@31f91000 {
+			compatible = "ti,am654-mailbox";
+			reg = <0x00 0x31f91000 0x00 0x200>;
+			#mbox-cells = <1>;
+			ti,mbox-num-users = <4>;
+			ti,mbox-num-fifos = <16>;
+			interrupt-parent = <&main_navss_intr>;
+		};
+
+		mailbox1_cluster2: mailbox@31f92000 {
+			compatible = "ti,am654-mailbox";
+			reg = <0x00 0x31f92000 0x00 0x200>;
+			#mbox-cells = <1>;
+			ti,mbox-num-users = <4>;
+			ti,mbox-num-fifos = <16>;
+			interrupt-parent = <&main_navss_intr>;
+		};
+
+		mailbox1_cluster3: mailbox@31f93000 {
+			compatible = "ti,am654-mailbox";
+			reg = <0x00 0x31f93000 0x00 0x200>;
+			#mbox-cells = <1>;
+			ti,mbox-num-users = <4>;
+			ti,mbox-num-fifos = <16>;
+			interrupt-parent = <&main_navss_intr>;
+		};
+
+		mailbox1_cluster4: mailbox@31f94000 {
+			compatible = "ti,am654-mailbox";
+			reg = <0x00 0x31f94000 0x00 0x200>;
+			#mbox-cells = <1>;
+			ti,mbox-num-users = <4>;
+			ti,mbox-num-fifos = <16>;
+			interrupt-parent = <&main_navss_intr>;
+		};
+
+		mailbox1_cluster5: mailbox@31f95000 {
+			compatible = "ti,am654-mailbox";
+			reg = <0x00 0x31f95000 0x00 0x200>;
+			#mbox-cells = <1>;
+			ti,mbox-num-users = <4>;
+			ti,mbox-num-fifos = <16>;
+			interrupt-parent = <&main_navss_intr>;
+		};
+
+		mailbox1_cluster6: mailbox@31f96000 {
+			compatible = "ti,am654-mailbox";
+			reg = <0x00 0x31f96000 0x00 0x200>;
+			#mbox-cells = <1>;
+			ti,mbox-num-users = <4>;
+			ti,mbox-num-fifos = <16>;
+			interrupt-parent = <&main_navss_intr>;
+		};
+
+		mailbox1_cluster7: mailbox@31f97000 {
+			compatible = "ti,am654-mailbox";
+			reg = <0x00 0x31f97000 0x00 0x200>;
+			#mbox-cells = <1>;
+			ti,mbox-num-users = <4>;
+			ti,mbox-num-fifos = <16>;
+			interrupt-parent = <&main_navss_intr>;
+		};
+
+		mailbox1_cluster8: mailbox@31f98000 {
+			compatible = "ti,am654-mailbox";
+			reg = <0x00 0x31f98000 0x00 0x200>;
+			#mbox-cells = <1>;
+			ti,mbox-num-users = <4>;
+			ti,mbox-num-fifos = <16>;
+			interrupt-parent = <&main_navss_intr>;
+		};
+
+		mailbox1_cluster9: mailbox@31f99000 {
+			compatible = "ti,am654-mailbox";
+			reg = <0x00 0x31f99000 0x00 0x200>;
+			#mbox-cells = <1>;
+			ti,mbox-num-users = <4>;
+			ti,mbox-num-fifos = <16>;
+			interrupt-parent = <&main_navss_intr>;
+		};
+
+		mailbox1_cluster10: mailbox@31f9a000 {
+			compatible = "ti,am654-mailbox";
+			reg = <0x00 0x31f9a000 0x00 0x200>;
+			#mbox-cells = <1>;
+			ti,mbox-num-users = <4>;
+			ti,mbox-num-fifos = <16>;
+			interrupt-parent = <&main_navss_intr>;
+		};
+
+		mailbox1_cluster11: mailbox@31f9b000 {
+			compatible = "ti,am654-mailbox";
+			reg = <0x00 0x31f9b000 0x00 0x200>;
+			#mbox-cells = <1>;
+			ti,mbox-num-users = <4>;
+			ti,mbox-num-fifos = <16>;
+			interrupt-parent = <&main_navss_intr>;
+		};
+
+		main_ringacc: ringacc@3c000000 {
+			compatible = "ti,am654-navss-ringacc";
+			reg = <0x0 0x3c000000 0x0 0x400000>,
+			      <0x0 0x38000000 0x0 0x400000>,
+			      <0x0 0x31120000 0x0 0x100>,
+			      <0x0 0x33000000 0x0 0x40000>;
+			reg-names = "rt", "fifos", "proxy_gcfg", "proxy_target";
+			ti,num-rings = <1024>;
+			ti,sci-rm-range-gp-rings = <0x1>;
+			ti,sci = <&sms>;
+			ti,sci-dev-id = <259>;
+			msi-parent = <&main_udmass_inta>;
+		};
+
+		main_udmap: dma-controller@31150000 {
+			compatible = "ti,j721e-navss-main-udmap";
+			reg = <0x0 0x31150000 0x0 0x100>,
+			      <0x0 0x34000000 0x0 0x80000>,
+			      <0x0 0x35000000 0x0 0x200000>;
+			reg-names = "gcfg", "rchanrt", "tchanrt";
+			msi-parent = <&main_udmass_inta>;
+			#dma-cells = <1>;
+
+			ti,sci = <&sms>;
+			ti,sci-dev-id = <263>;
+			ti,ringacc = <&main_ringacc>;
+
+			ti,sci-rm-range-tchan = <0x0d>, /* TX_CHAN */
+						<0x0f>, /* TX_HCHAN */
+						<0x10>; /* TX_UHCHAN */
+			ti,sci-rm-range-rchan = <0x0a>, /* RX_CHAN */
+						<0x0b>, /* RX_HCHAN */
+						<0x0c>; /* RX_UHCHAN */
+			ti,sci-rm-range-rflow = <0x00>; /* GP RFLOW */
+		};
+
+		cpts@310d0000 {
+			compatible = "ti,j721e-cpts";
+			reg = <0x0 0x310d0000 0x0 0x400>;
+			reg-names = "cpts";
+			clocks = <&k3_clks 226 5>;
+			clock-names = "cpts";
+			interrupts-extended = <&main_navss_intr 391>;
+			interrupt-names = "cpts";
+			ti,cpts-periodic-outputs = <6>;
+			ti,cpts-ext-ts-inputs = <8>;
+		};
+	};
+
+	main_mcan0: can@2701000 {
+		compatible = "bosch,m_can";
+		reg = <0x00 0x02701000 0x00 0x200>,
+		      <0x00 0x02708000 0x00 0x8000>;
+		reg-names = "m_can", "message_ram";
+		power-domains = <&k3_pds 182 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 182 0>, <&k3_clks 182 1>;
+		clock-names = "hclk", "cclk";
+		interrupts = <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "int0", "int1";
+		bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
+	};
+
+	main_mcan1: can@2711000 {
+		compatible = "bosch,m_can";
+		reg = <0x00 0x02711000 0x00 0x200>,
+		      <0x00 0x02718000 0x00 0x8000>;
+		reg-names = "m_can", "message_ram";
+		power-domains = <&k3_pds 183 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 183 0>, <&k3_clks 183 1>;
+		clock-names = "hclk", "cclk";
+		interrupts = <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 128 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "int0", "int1";
+		bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
+	};
+
+	main_mcan2: can@2721000 {
+		compatible = "bosch,m_can";
+		reg = <0x00 0x02721000 0x00 0x200>,
+		      <0x00 0x02728000 0x00 0x8000>;
+		reg-names = "m_can", "message_ram";
+		power-domains = <&k3_pds 184 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 184 0>, <&k3_clks 184 1>;
+		clock-names = "hclk", "cclk";
+		interrupts = <GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "int0", "int1";
+		bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
+	};
+
+	main_mcan3: can@2731000 {
+		compatible = "bosch,m_can";
+		reg = <0x00 0x02731000 0x00 0x200>,
+		      <0x00 0x02738000 0x00 0x8000>;
+		reg-names = "m_can", "message_ram";
+		power-domains = <&k3_pds 185 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 185 0>, <&k3_clks 185 1>;
+		clock-names = "hclk", "cclk";
+		interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "int0", "int1";
+		bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
+	};
+
+	main_mcan4: can@2741000 {
+		compatible = "bosch,m_can";
+		reg = <0x00 0x02741000 0x00 0x200>,
+		      <0x00 0x02748000 0x00 0x8000>;
+		reg-names = "m_can", "message_ram";
+		power-domains = <&k3_pds 186 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 186 0>, <&k3_clks 186 1>;
+		clock-names = "hclk", "cclk";
+		interrupts = <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "int0", "int1";
+		bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
+	};
+
+	main_mcan5: can@2751000 {
+		compatible = "bosch,m_can";
+		reg = <0x00 0x02751000 0x00 0x200>,
+		      <0x00 0x02758000 0x00 0x8000>;
+		reg-names = "m_can", "message_ram";
+		power-domains = <&k3_pds 187 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 187 0>, <&k3_clks 187 1>;
+		clock-names = "hclk", "cclk";
+		interrupts = <GIC_SPI 139 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "int0", "int1";
+		bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
+	};
+
+	main_mcan6: can@2761000 {
+		compatible = "bosch,m_can";
+		reg = <0x00 0x02761000 0x00 0x200>,
+		      <0x00 0x02768000 0x00 0x8000>;
+		reg-names = "m_can", "message_ram";
+		power-domains = <&k3_pds 188 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 188 0>, <&k3_clks 188 1>;
+		clock-names = "hclk", "cclk";
+		interrupts = <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "int0", "int1";
+		bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
+	};
+
+	main_mcan7: can@2771000 {
+		compatible = "bosch,m_can";
+		reg = <0x00 0x02771000 0x00 0x200>,
+		      <0x00 0x02778000 0x00 0x8000>;
+		reg-names = "m_can", "message_ram";
+		power-domains = <&k3_pds 189 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 189 0>, <&k3_clks 189 1>;
+		clock-names = "hclk", "cclk";
+		interrupts = <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "int0", "int1";
+		bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
+	};
+
+	main_mcan8: can@2781000 {
+		compatible = "bosch,m_can";
+		reg = <0x00 0x02781000 0x00 0x200>,
+		      <0x00 0x02788000 0x00 0x8000>;
+		reg-names = "m_can", "message_ram";
+		power-domains = <&k3_pds 190 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 190 0>, <&k3_clks 190 1>;
+		clock-names = "hclk", "cclk";
+		interrupts = <GIC_SPI 576 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 577 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "int0", "int1";
+		bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
+	};
+
+	main_mcan9: can@2791000 {
+		compatible = "bosch,m_can";
+		reg = <0x00 0x02791000 0x00 0x200>,
+		      <0x00 0x02798000 0x00 0x8000>;
+		reg-names = "m_can", "message_ram";
+		power-domains = <&k3_pds 191 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 191 0>, <&k3_clks 191 1>;
+		clock-names = "hclk", "cclk";
+		interrupts = <GIC_SPI 579 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 580 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "int0", "int1";
+		bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
+	};
+
+	main_mcan10: can@27a1000 {
+		compatible = "bosch,m_can";
+		reg = <0x00 0x027a1000 0x00 0x200>,
+		      <0x00 0x027a8000 0x00 0x8000>;
+		reg-names = "m_can", "message_ram";
+		power-domains = <&k3_pds 192 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 192 0>, <&k3_clks 192 1>;
+		clock-names = "hclk", "cclk";
+		interrupts = <GIC_SPI 582 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 583 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "int0", "int1";
+		bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
+	};
+
+	main_mcan11: can@27b1000 {
+		compatible = "bosch,m_can";
+		reg = <0x00 0x027b1000 0x00 0x200>,
+		      <0x00 0x027b8000 0x00 0x8000>;
+		reg-names = "m_can", "message_ram";
+		power-domains = <&k3_pds 193 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 193 0>, <&k3_clks 193 1>;
+		clock-names = "hclk", "cclk";
+		interrupts = <GIC_SPI 585 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 586 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "int0", "int1";
+		bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
+	};
+
+	main_mcan12: can@27c1000 {
+		compatible = "bosch,m_can";
+		reg = <0x00 0x027c1000 0x00 0x200>,
+		      <0x00 0x027c8000 0x00 0x8000>;
+		reg-names = "m_can", "message_ram";
+		power-domains = <&k3_pds 194 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 194 0>, <&k3_clks 194 1>;
+		clock-names = "hclk", "cclk";
+		interrupts = <GIC_SPI 588 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 589 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "int0", "int1";
+		bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
+	};
+
+	main_mcan13: can@27d1000 {
+		compatible = "bosch,m_can";
+		reg = <0x00 0x027d1000 0x00 0x200>,
+		      <0x00 0x027d8000 0x00 0x8000>;
+		reg-names = "m_can", "message_ram";
+		power-domains = <&k3_pds 195 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 195 0>, <&k3_clks 195 1>;
+		clock-names = "hclk", "cclk";
+		interrupts = <GIC_SPI 591 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 592 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "int0", "int1";
+		bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
+	};
+
+	main_mcan14: can@2681000 {
+		compatible = "bosch,m_can";
+		reg = <0x00 0x02681000 0x00 0x200>,
+		      <0x00 0x02688000 0x00 0x8000>;
+		reg-names = "m_can", "message_ram";
+		power-domains = <&k3_pds 197 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 197 0>, <&k3_clks 197 1>;
+		clock-names = "hclk", "cclk";
+		interrupts = <GIC_SPI 594 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 595 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "int0", "int1";
+		bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
+	};
+
+	main_mcan15: can@2691000 {
+		compatible = "bosch,m_can";
+		reg = <0x00 0x02691000 0x00 0x200>,
+		      <0x00 0x02698000 0x00 0x8000>;
+		reg-names = "m_can", "message_ram";
+		power-domains = <&k3_pds 199 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 199 0>, <&k3_clks 199 1>;
+		clock-names = "hclk", "cclk";
+		interrupts = <GIC_SPI 597 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 598 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "int0", "int1";
+		bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
+	};
+
+	main_mcan16: can@26a1000 {
+		compatible = "bosch,m_can";
+		reg = <0x00 0x026a1000 0x00 0x200>,
+		      <0x00 0x026a8000 0x00 0x8000>;
+		reg-names = "m_can", "message_ram";
+		power-domains = <&k3_pds 201 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 201 0>, <&k3_clks 201 1>;
+		clock-names = "hclk", "cclk";
+		interrupts = <GIC_SPI 784 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 785 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "int0", "int1";
+		bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
+	};
+
+	main_mcan17: can@26b1000 {
+		compatible = "bosch,m_can";
+		reg = <0x00 0x026b1000 0x00 0x200>,
+		      <0x00 0x026b8000 0x00 0x8000>;
+		reg-names = "m_can", "message_ram";
+		power-domains = <&k3_pds 206 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 206 0>, <&k3_clks 206 1>;
+		clock-names = "hclk", "cclk";
+		interrupts = <GIC_SPI 787 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 788 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "int0", "int1";
+		bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
+	};
+};
diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi
new file mode 100644
index 000000000000..4d1bfabd1313
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi
@@ -0,0 +1,302 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device Tree Source for J721S2 SoC Family MCU/WAKEUP Domain peripherals
+ *
+ * Copyright (C) 2021 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+&cbass_mcu_wakeup {
+	sms: system-controller@44083000 {
+		compatible = "ti,k2g-sci";
+		ti,host-id = <12>;
+
+		mbox-names = "rx", "tx";
+
+		mboxes = <&secure_proxy_main 11>,
+			 <&secure_proxy_main 13>;
+
+		reg-names = "debug_messages";
+		reg = <0x00 0x44083000 0x00 0x1000>;
+
+		k3_pds: power-controller {
+			compatible = "ti,sci-pm-domain";
+			#power-domain-cells = <2>;
+		};
+
+		k3_clks: clock-controller {
+			compatible = "ti,k2g-sci-clk";
+			#clock-cells = <2>;
+		};
+
+		k3_reset: reset-controller {
+			compatible = "ti,sci-reset";
+			#reset-cells = <2>;
+		};
+	};
+
+	chipid@43000014 {
+		compatible = "ti,am654-chipid";
+		reg = <0x00 0x43000014 0x00 0x4>;
+	};
+
+	mcu_ram: sram@41c00000 {
+		compatible = "mmio-sram";
+		reg = <0x00 0x41c00000 0x00 0x100000>;
+		ranges = <0x00 0x00 0x41c00000 0x100000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+	};
+
+	wkup_pmx0: pinctrl@4301c000 {
+		compatible = "pinctrl-single";
+		/* Proxy 0 addressing */
+		reg = <0x00 0x4301c000 0x00 0x178>;
+		#pinctrl-cells = <1>;
+		pinctrl-single,register-width = <32>;
+		pinctrl-single,function-mask = <0xffffffff>;
+	};
+
+	wkup_gpio_intr: interrupt-controller@42200000 {
+		compatible = "ti,sci-intr";
+		reg = <0x00 0x42200000 0x00 0x400>;
+		ti,intr-trigger-type = <1>;
+		interrupt-controller;
+		interrupt-parent = <&gic500>;
+		#interrupt-cells = <1>;
+		ti,sci = <&sms>;
+		ti,sci-dev-id = <125>;
+		ti,interrupt-ranges = <16 928 16>;
+	};
+
+	mcu_conf: syscon@40f00000 {
+		compatible = "syscon", "simple-mfd";
+		reg = <0x0 0x40f00000 0x0 0x20000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x0 0x40f00000 0x20000>;
+
+		phy_gmii_sel: phy@4040 {
+			compatible = "ti,am654-phy-gmii-sel";
+			reg = <0x4040 0x4>;
+			#phy-cells = <1>;
+		};
+
+	};
+
+	wkup_uart0: serial@42300000 {
+		compatible = "ti,j721e-uart", "ti,am654-uart";
+		reg = <0x00 0x42300000 0x00 0x200>;
+		interrupts = <GIC_SPI 897 IRQ_TYPE_LEVEL_HIGH>;
+		current-speed = <115200>;
+		clocks = <&k3_clks 359 3>;
+		clock-names = "fclk";
+		power-domains = <&k3_pds 359 TI_SCI_PD_EXCLUSIVE>;
+	};
+
+	mcu_uart0: serial@40a00000 {
+		compatible = "ti,j721e-uart", "ti,am654-uart";
+		reg = <0x00 0x40a00000 0x00 0x200>;
+		interrupts = <GIC_SPI 846 IRQ_TYPE_LEVEL_HIGH>;
+		current-speed = <115200>;
+		clocks = <&k3_clks 149 3>;
+		clock-names = "fclk";
+		power-domains = <&k3_pds 149 TI_SCI_PD_EXCLUSIVE>;
+	};
+
+	wkup_gpio0: gpio@42110000 {
+		compatible = "ti,j721e-gpio", "ti,keystone-gpio";
+		reg = <0x00 0x42110000 0x00 0x100>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-parent = <&wkup_gpio_intr>;
+		interrupts = <103>, <104>, <105>, <106>, <107>, <108>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		ti,ngpio = <89>;
+		ti,davinci-gpio-unbanked = <0>;
+		power-domains = <&k3_pds 115 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 115 0>;
+		clock-names = "gpio";
+	};
+
+	wkup_gpio1: gpio@42100000 {
+		compatible = "ti,j721e-gpio", "ti,keystone-gpio";
+		reg = <0x00 0x42100000 0x00 0x100>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-parent = <&wkup_gpio_intr>;
+		interrupts = <112>, <113>, <114>, <115>, <116>, <117>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		ti,ngpio = <89>;
+		ti,davinci-gpio-unbanked = <0>;
+		power-domains = <&k3_pds 116 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 116 0>;
+		clock-names = "gpio";
+	};
+
+	wkup_i2c0: i2c@42120000 {
+		compatible = "ti,j721e-i2c", "ti,omap4-i2c";
+		reg = <0x00 0x42120000 0x00 0x100>;
+		interrupts = <GIC_SPI 896 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		clocks = <&k3_clks 223 1>;
+		clock-names = "fck";
+		power-domains = <&k3_pds 223 TI_SCI_PD_EXCLUSIVE>;
+	};
+
+	mcu_i2c0: i2c@40b00000 {
+		compatible = "ti,j721e-i2c", "ti,omap4-i2c";
+		reg = <0x00 0x40b00000 0x00 0x100>;
+		interrupts = <GIC_SPI 852 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		clocks = <&k3_clks 221 1>;
+		clock-names = "fck";
+		power-domains = <&k3_pds 221 TI_SCI_PD_EXCLUSIVE>;
+	};
+
+	mcu_i2c1: i2c@40b10000 {
+		compatible = "ti,j721e-i2c", "ti,omap4-i2c";
+		reg = <0x00 0x40b10000 0x00 0x100>;
+		interrupts = <GIC_SPI 853 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		clocks = <&k3_clks 222 1>;
+		clock-names = "fck";
+		power-domains = <&k3_pds 222 TI_SCI_PD_EXCLUSIVE>;
+	};
+
+	mcu_mcan0: can@40528000 {
+		compatible = "bosch,m_can";
+		reg = <0x00 0x40528000 0x00 0x200>,
+		      <0x00 0x40500000 0x00 0x8000>;
+		reg-names = "m_can", "message_ram";
+		power-domains = <&k3_pds 207 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 207 0>, <&k3_clks 207 1>;
+		clock-names = "hclk", "cclk";
+		interrupts = <GIC_SPI 832 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 833 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "int0", "int1";
+		bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
+	};
+
+	mcu_mcan1: can@40568000 {
+		compatible = "bosch,m_can";
+		reg = <0x00 0x40568000 0x00 0x200>,
+		      <0x00 0x40540000 0x00 0x8000>;
+		reg-names = "m_can", "message_ram";
+		power-domains = <&k3_pds 208 TI_SCI_PD_EXCLUSIVE>;
+		clocks = <&k3_clks 208 0>, <&k3_clks 208 1>;
+		clock-names = "hclk", "cclk";
+		interrupts = <GIC_SPI 835 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 836 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "int0", "int1";
+		bosch,mram-cfg = <0x0 128 64 64 64 64 32 32>;
+	};
+
+	mcu_navss: bus@28380000{
+		compatible = "simple-mfd";
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges = <0x00 0x28380000 0x00 0x28380000 0x00 0x03880000>;
+		dma-coherent;
+		dma-ranges;
+
+		ti,sci-dev-id = <267>;
+
+		mcu_ringacc: ringacc@2b800000 {
+			compatible = "ti,am654-navss-ringacc";
+			reg = <0x0 0x2b800000 0x0 0x400000>,
+			      <0x0 0x2b000000 0x0 0x400000>,
+			      <0x0 0x28590000 0x0 0x100>,
+			      <0x0 0x2a500000 0x0 0x40000>;
+			reg-names = "rt", "fifos", "proxy_gcfg", "proxy_target";
+			ti,num-rings = <286>;
+			ti,sci-rm-range-gp-rings = <0x1>;
+			ti,sci = <&sms>;
+			ti,sci-dev-id = <272>;
+			msi-parent = <&main_udmass_inta>;
+		};
+
+		mcu_udmap: dma-controller@285c0000 {
+			compatible = "ti,j721e-navss-mcu-udmap";
+			reg = <0x0 0x285c0000 0x0 0x100>,
+			      <0x0 0x2a800000 0x0 0x40000>,
+			      <0x0 0x2aa00000 0x0 0x40000>;
+			reg-names = "gcfg", "rchanrt", "tchanrt";
+			msi-parent = <&main_udmass_inta>;
+			#dma-cells = <1>;
+
+			ti,sci = <&sms>;
+			ti,sci-dev-id = <273>;
+			ti,ringacc = <&mcu_ringacc>;
+			ti,sci-rm-range-tchan = <0x0d>, /* TX_CHAN */
+						<0x0f>; /* TX_HCHAN */
+			ti,sci-rm-range-rchan = <0x0a>, /* RX_CHAN */
+						<0x0b>; /* RX_HCHAN */
+			ti,sci-rm-range-rflow = <0x00>; /* GP RFLOW */
+		};
+	};
+
+	mcu_cpsw: ethernet@46000000 {
+		compatible = "ti,j721e-cpsw-nuss";
+		#address-cells = <2>;
+		#size-cells = <2>;
+		reg = <0x0 0x46000000 0x0 0x200000>;
+		reg-names = "cpsw_nuss";
+		ranges = <0x0 0x0 0x0 0x46000000 0x0 0x200000>;
+		dma-coherent;
+		clocks = <&k3_clks 29 28>;
+		clock-names = "fck";
+		power-domains = <&k3_pds 29 TI_SCI_PD_EXCLUSIVE>;
+
+		dmas = <&mcu_udmap 0xf000>,
+		       <&mcu_udmap 0xf001>,
+		       <&mcu_udmap 0xf002>,
+		       <&mcu_udmap 0xf003>,
+		       <&mcu_udmap 0xf004>,
+		       <&mcu_udmap 0xf005>,
+		       <&mcu_udmap 0xf006>,
+		       <&mcu_udmap 0xf007>,
+		       <&mcu_udmap 0x7000>;
+		dma-names = "tx0", "tx1", "tx2", "tx3",
+			    "tx4", "tx5", "tx6", "tx7",
+			    "rx";
+
+		ethernet-ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			cpsw_port1: port@1 {
+				reg = <1>;
+				ti,mac-only;
+				label = "port1";
+				ti,syscon-efuse = <&mcu_conf 0x200>;
+				phys = <&phy_gmii_sel 1>;
+			};
+		};
+
+		davinci_mdio: mdio@f00 {
+			compatible = "ti,cpsw-mdio","ti,davinci_mdio";
+			reg = <0x0 0xf00 0x0 0x100>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			clocks = <&k3_clks 29 28>;
+			clock-names = "fck";
+			bus_freq = <1000000>;
+		};
+
+		cpts@3d000 {
+			compatible = "ti,am65-cpts";
+			reg = <0x0 0x3d000 0x0 0x400>;
+			clocks = <&k3_clks 29 3>;
+			clock-names = "cpts";
+			interrupts-extended = <&gic500 GIC_SPI 858 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "cpts";
+			ti,cpts-ext-ts-inputs = <4>;
+			ti,cpts-periodic-outputs = <2>;
+		};
+	};
+};
diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi b/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
new file mode 100644
index 000000000000..76f0ceacb6d4
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-j721s2-som-p0.dtsi
@@ -0,0 +1,175 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * SoM: https://www.ti.com/lit/zip/sprr439
+ *
+ * Copyright (C) 2021 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+/dts-v1/;
+
+#include "k3-j721s2.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	memory@80000000 {
+		device_type = "memory";
+		/* 16 GB RAM */
+		reg = <0x00 0x80000000 0x00 0x80000000>,
+		      <0x08 0x80000000 0x03 0x80000000>;
+	};
+
+	/* Reserving memory regions still pending */
+	reserved_memory: reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		secure_ddr: optee@9e800000 {
+			reg = <0x00 0x9e800000 0x00 0x01800000>;
+			alignment = <0x1000>;
+			no-map;
+		};
+	};
+
+	transceiver0: can-phy0 {
+		/* standby pin has been grounded by default */
+		compatible = "ti,tcan1042";
+		#phy-cells = <0>;
+		max-bitrate = <5000000>;
+	};
+};
+
+&main_pmx0 {
+	main_i2c0_pins_default: main-i2c0-pins-default {
+		pinctrl-single,pins = <
+			J721S2_IOPAD(0x0e0, PIN_INPUT_PULLUP, 0) /* (AH25) I2C0_SCL */
+			J721S2_IOPAD(0x0e4, PIN_INPUT_PULLUP, 0) /* (AE24) I2C0_SDA */
+		>;
+	};
+
+	main_mcan16_pins_default: main-mcan16-pins-default {
+		pinctrl-single,pins = <
+			J721S2_IOPAD(0x028, PIN_INPUT, 0) /* (AB24) MCAN16_RX */
+			J721S2_IOPAD(0x024, PIN_OUTPUT, 0) /* (Y28) MCAN16_TX */
+		>;
+	};
+};
+
+&main_i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_i2c0_pins_default>;
+	clock-frequency = <400000>;
+
+	exp_som: gpio@21 {
+		compatible = "ti,tca6408";
+		reg = <0x21>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names = "USB2.0_MUX_SEL", "CANUART_MUX1_SEL0",
+				  "CANUART_MUX2_SEL0", "CANUART_MUX_SEL1",
+				  "GPIO_RGMII1_RST", "GPIO_eDP_ENABLE",
+				   "GPIO_LIN_EN", "CAN_STB";
+	};
+};
+
+&main_mcan16 {
+	pinctrl-0 = <&main_mcan16_pins_default>;
+	pinctrl-names = "default";
+	phys = <&transceiver0>;
+};
+
+&mailbox0_cluster0 {
+	status = "disabled";
+};
+
+&mailbox0_cluster1 {
+	status = "disabled";
+};
+
+&mailbox0_cluster2 {
+	status = "disabled";
+};
+
+&mailbox0_cluster3 {
+	status = "disabled";
+};
+
+&mailbox0_cluster4 {
+	status = "disabled";
+};
+
+&mailbox0_cluster5 {
+	status = "disabled";
+};
+
+&mailbox0_cluster6 {
+	status = "disabled";
+};
+
+&mailbox0_cluster7 {
+	status = "disabled";
+};
+
+&mailbox0_cluster8 {
+	status = "disabled";
+};
+
+&mailbox0_cluster9 {
+	status = "disabled";
+};
+
+&mailbox0_cluster10 {
+	status = "disabled";
+};
+
+&mailbox0_cluster11 {
+	status = "disabled";
+};
+
+&mailbox1_cluster0 {
+	status = "disabled";
+};
+
+&mailbox1_cluster1 {
+	status = "disabled";
+};
+
+&mailbox1_cluster2 {
+	status = "disabled";
+};
+
+&mailbox1_cluster3 {
+	status = "disabled";
+};
+
+&mailbox1_cluster4 {
+	status = "disabled";
+};
+
+&mailbox1_cluster5 {
+	status = "disabled";
+};
+
+&mailbox1_cluster6 {
+	status = "disabled";
+};
+
+&mailbox1_cluster7 {
+	status = "disabled";
+};
+
+&mailbox1_cluster8 {
+	status = "disabled";
+};
+
+&mailbox1_cluster9 {
+	status = "disabled";
+};
+
+&mailbox1_cluster10 {
+	status = "disabled";
+};
+
+&mailbox1_cluster11 {
+	status = "disabled";
+};
diff --git a/arch/arm64/boot/dts/ti/k3-j721s2.dtsi b/arch/arm64/boot/dts/ti/k3-j721s2.dtsi
new file mode 100644
index 000000000000..7b930a85a29d
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-j721s2.dtsi
@@ -0,0 +1,168 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device Tree Source for J721S2 SoC Family
+ *
+ * TRM (SPRUJ28 – NOVEMBER 2021) : http://www.ti.com/lit/pdf/spruj28
+ *
+ * Copyright (C) 2021 Texas Instruments Incorporated - https://www.ti.com/
+ *
+ */
+
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/pinctrl/k3.h>
+#include <dt-bindings/soc/ti,sci_pm_domain.h>
+
+/ {
+
+	model = "Texas Instruments K3 J721S2 SoC";
+	compatible = "ti,j721s2";
+	interrupt-parent = <&gic500>;
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	chosen { };
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		cpu-map {
+			cluster0: cluster0 {
+				core0 {
+					cpu = <&cpu0>;
+				};
+
+				core1 {
+					cpu = <&cpu1>;
+				};
+			};
+		};
+
+		cpu0: cpu@0 {
+			compatible = "arm,cortex-a72";
+			reg = <0x000>;
+			device_type = "cpu";
+			enable-method = "psci";
+			i-cache-size = <0xc000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <256>;
+			next-level-cache = <&L2_0>;
+		};
+
+		cpu1: cpu@1 {
+			compatible = "arm,cortex-a72";
+			reg = <0x001>;
+			device_type = "cpu";
+			enable-method = "psci";
+			i-cache-size = <0xc000>;
+			i-cache-line-size = <64>;
+			i-cache-sets = <256>;
+			d-cache-size = <0x8000>;
+			d-cache-line-size = <64>;
+			d-cache-sets = <256>;
+			next-level-cache = <&L2_0>;
+		};
+	};
+
+	L2_0: l2-cache0 {
+		compatible = "cache";
+		cache-level = <2>;
+		cache-size = <0x100000>;
+		cache-line-size = <64>;
+		cache-sets = <1024>;
+		next-level-cache = <&msmc_l3>;
+	};
+
+	msmc_l3: l3-cache0 {
+		compatible = "cache";
+		cache-level = <3>;
+	};
+
+	firmware {
+		optee {
+			compatible = "linaro,optee-tz";
+			method = "smc";
+		};
+
+		psci: psci {
+			compatible = "arm,psci-1.0";
+			method = "smc";
+		};
+	};
+
+	a72_timer0: timer-cl0-cpu0 {
+		compatible = "arm,armv8-timer";
+		interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW>, /* cntpsirq */
+			     <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW>, /* cntpnsirq */
+			     <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW>, /* cntvirq */
+			     <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW>; /* cnthpirq */
+
+	};
+
+	pmu: pmu {
+		compatible = "arm,cortex-a72-pmu";
+		/* Recommendation from GIC500 TRM Table A.3 */
+		interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH>;
+	};
+
+	cbass_main: bus@100000 {
+		compatible = "simple-bus";
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges = <0x00 0x00100000 0x00 0x00100000 0x00 0x00020000>, /* ctrl mmr */
+			 <0x00 0x00600000 0x00 0x00600000 0x00 0x00031100>, /* GPIO */
+			 <0x00 0x01000000 0x00 0x01000000 0x00 0x0d000000>, /* Most peripherals */
+			 <0x00 0x0d800000 0x00 0x0d800000 0x00 0x00800000>, /* PCIe Core*/
+			 <0x00 0x18000000 0x00 0x18000000 0x00 0x08000000>, /* PCIe1 DAT0 */
+			 <0x00 0x64800000 0x00 0x64800000 0x00 0x0070c000>, /* C71_1 */
+			 <0x00 0x65800000 0x00 0x65800000 0x00 0x0070c000>, /* C71_2 */
+			 <0x00 0x6f000000 0x00 0x6f000000 0x00 0x00310000>, /* A72 PERIPHBASE */
+			 <0x00 0x70000000 0x00 0x70000000 0x00 0x00400000>, /* MSMC RAM */
+			 <0x00 0x30000000 0x00 0x30000000 0x00 0x0c400000>, /* MAIN NAVSS */
+			 <0x41 0x00000000 0x41 0x00000000 0x01 0x00000000>, /* PCIe1 DAT1 */
+			 <0x4e 0x20000000 0x4e 0x20000000 0x00 0x00080000>, /* GPU */
+
+			 /* MCUSS_WKUP Range */
+			 <0x00 0x28380000 0x00 0x28380000 0x00 0x03880000>,
+			 <0x00 0x40200000 0x00 0x40200000 0x00 0x00998400>,
+			 <0x00 0x40f00000 0x00 0x40f00000 0x00 0x00020000>,
+			 <0x00 0x41000000 0x00 0x41000000 0x00 0x00020000>,
+			 <0x00 0x41400000 0x00 0x41400000 0x00 0x00020000>,
+			 <0x00 0x41c00000 0x00 0x41c00000 0x00 0x00100000>,
+			 <0x00 0x42040000 0x00 0x42040000 0x00 0x03ac2400>,
+			 <0x00 0x45100000 0x00 0x45100000 0x00 0x00c24000>,
+			 <0x00 0x46000000 0x00 0x46000000 0x00 0x00200000>,
+			 <0x00 0x47000000 0x00 0x47000000 0x00 0x00068400>,
+			 <0x00 0x50000000 0x00 0x50000000 0x00 0x10000000>,
+			 <0x05 0x00000000 0x05 0x00000000 0x01 0x00000000>,
+			 <0x07 0x00000000 0x07 0x00000000 0x01 0x00000000>;
+
+		cbass_mcu_wakeup: bus@28380000 {
+			compatible = "simple-bus";
+			#address-cells = <2>;
+			#size-cells = <2>;
+			ranges = <0x00 0x28380000 0x00 0x28380000 0x00 0x03880000>, /* MCU NAVSS*/
+				 <0x00 0x40200000 0x00 0x40200000 0x00 0x00998400>, /* First peripheral window */
+				 <0x00 0x40f00000 0x00 0x40f00000 0x00 0x00020000>, /* CTRL_MMR0 */
+				 <0x00 0x41000000 0x00 0x41000000 0x00 0x00020000>, /* MCU R5F Core0 */
+				 <0x00 0x41400000 0x00 0x41400000 0x00 0x00020000>, /* MCU R5F Core1 */
+				 <0x00 0x41c00000 0x00 0x41c00000 0x00 0x00100000>, /* MCU SRAM */
+				 <0x00 0x42040000 0x00 0x42040000 0x00 0x03ac2400>, /* WKUP peripheral window */
+				 <0x00 0x45100000 0x00 0x45100000 0x00 0x00c24000>, /* MMRs, remaining NAVSS */
+				 <0x00 0x46000000 0x00 0x46000000 0x00 0x00200000>, /* CPSW */
+				 <0x00 0x47000000 0x00 0x47000000 0x00 0x00068400>, /* OSPI register space */
+				 <0x00 0x50000000 0x00 0x50000000 0x00 0x10000000>, /* FSS OSPI0/1 data region 0 */
+				 <0x05 0x00000000 0x05 0x00000000 0x01 0x00000000>, /* FSS OSPI0 data region 3 */
+				 <0x07 0x00000000 0x07 0x00000000 0x01 0x00000000>; /* FSS OSPI1 data region 3*/
+
+		};
+
+	};
+};
+
+/* Now include peripherals from each bus segment */
+#include "k3-j721s2-main.dtsi"
+#include "k3-j721s2-mcu-wakeup.dtsi"
diff --git a/arch/arm64/boot/dts/toshiba/tmpv7708-rm-mbrc.dts b/arch/arm64/boot/dts/toshiba/tmpv7708-rm-mbrc.dts
index 9375b0faeea2..d209fdc98597 100644
--- a/arch/arm64/boot/dts/toshiba/tmpv7708-rm-mbrc.dts
+++ b/arch/arm64/boot/dts/toshiba/tmpv7708-rm-mbrc.dts
@@ -32,22 +32,16 @@
 
 &uart0 {
 	status = "okay";
-	clocks = <&uart_clk>;
-	clock-names = "apb_pclk";
 };
 
 &uart1 {
 	status = "okay";
-	clocks = <&uart_clk>;
-	clock-names = "apb_pclk";
 };
 
 &piether {
 	status = "okay";
 	phy-handle = <&phy0>;
 	phy-mode = "rgmii-id";
-	clocks = <&clk300mhz>, <&clk125mhz>;
-	clock-names = "stmmaceth", "phy_ref_clk";
 
 	mdio0 {
 		#address-cells = <1>;
@@ -62,7 +56,6 @@
 
 &wdt {
 	status = "okay";
-	clocks = <&wdt_clk>;
 };
 
 &gpio {
@@ -79,6 +72,4 @@
 
 &pcie {
 	status = "okay";
-	clocks = <&extclk100mhz>, <&clk600mhz>, <&clk25mhz>;
-	clock-names = "ref", "core", "aux";
 };
diff --git a/arch/arm64/boot/dts/toshiba/tmpv7708-visrobo-vrb.dts b/arch/arm64/boot/dts/toshiba/tmpv7708-visrobo-vrb.dts
index d0817463706e..ed7aa7e457b1 100644
--- a/arch/arm64/boot/dts/toshiba/tmpv7708-visrobo-vrb.dts
+++ b/arch/arm64/boot/dts/toshiba/tmpv7708-visrobo-vrb.dts
@@ -32,22 +32,16 @@
 
 &uart0 {
 	status = "okay";
-	clocks = <&uart_clk>;
-	clock-names = "apb_pclk";
 };
 
 &uart1 {
 	status = "okay";
-	clocks = <&uart_clk>;
-	clock-names = "apb_pclk";
 };
 
 &piether {
 	status = "okay";
 	phy-handle = <&phy0>;
 	phy-mode = "rgmii-id";
-	clocks = <&clk300mhz>, <&clk125mhz>;
-	clock-names = "stmmaceth", "phy_ref_clk";
 
 	mdio0 {
 		#address-cells = <1>;
diff --git a/arch/arm64/boot/dts/toshiba/tmpv7708-visrobo-vrc.dtsi b/arch/arm64/boot/dts/toshiba/tmpv7708-visrobo-vrc.dtsi
index f0a93db6dde6..0c8321022a73 100644
--- a/arch/arm64/boot/dts/toshiba/tmpv7708-visrobo-vrc.dtsi
+++ b/arch/arm64/boot/dts/toshiba/tmpv7708-visrobo-vrc.dtsi
@@ -13,7 +13,6 @@
 
 &wdt {
 	status = "okay";
-	clocks = <&wdt_clk>;
 };
 
 &gpio {
@@ -26,8 +25,6 @@
 
 &spi0 {
 	status = "okay";
-	clocks = <&clk300mhz>, <&clk150mhz>;
-	clock-names = "sspclk", "apb_pclk";
 
 	mmc-slot@0 {
 		compatible = "mmc-spi-slot";
@@ -40,5 +37,4 @@
 
 &i2c0 {
 	status = "okay";
-	clocks = <&clk150mhz>;
 };
diff --git a/arch/arm64/boot/dts/toshiba/tmpv7708.dtsi b/arch/arm64/boot/dts/toshiba/tmpv7708.dtsi
index 01d7ee61ad25..0fc32c036f30 100644
--- a/arch/arm64/boot/dts/toshiba/tmpv7708.dtsi
+++ b/arch/arm64/boot/dts/toshiba/tmpv7708.dtsi
@@ -7,6 +7,7 @@
  *
  */
 
+#include <dt-bindings/clock/toshiba,tmpv770x.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 
@@ -128,47 +129,6 @@
 			<GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>;
 	};
 
-	uart_clk: uart-clk {
-		compatible = "fixed-clock";
-		clock-frequency = <150000000>;
-		#clock-cells = <0>;
-	};
-
-	clk25mhz: clk25mhz {
-		compatible = "fixed-clock";
-		#clock-cells = <0>;
-		clock-frequency = <25000000>;
-		clock-output-names = "clk25mhz";
-	};
-
-	clk125mhz: clk125mhz {
-		compatible = "fixed-clock";
-		clock-frequency = <125000000>;
-		#clock-cells = <0>;
-		clock-output-names = "clk125mhz";
-	};
-
-	clk150mhz: clk150mhz {
-		compatible = "fixed-clock";
-		clock-frequency = <150000000>;
-		#clock-cells = <0>;
-		clock-output-names = "clk150mhz";
-	};
-
-	clk300mhz: clk300mhz {
-		compatible = "fixed-clock";
-		clock-frequency = <300000000>;
-		#clock-cells = <0>;
-		clock-output-names = "clk300mhz";
-	};
-
-	clk600mhz: clk600mhz {
-		compatible = "fixed-clock";
-		#clock-cells = <0>;
-		clock-frequency = <600000000>;
-		clock-output-names = "clk600mhz";
-	};
-
 	extclk100mhz: extclk100mhz {
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
@@ -176,9 +136,9 @@
 		clock-output-names = "extclk100mhz";
 	};
 
-	wdt_clk: wdt-clk {
+	osc2_clk: osc2-clk {
 		compatible = "fixed-clock";
-		clock-frequency = <150000000>;
+		clock-frequency = <20000000>;
 		#clock-cells = <0>;
 	};
 
@@ -216,12 +176,28 @@
 			interrupt-parent = <&gic>;
 		};
 
+		pipllct: clock-controller@24220000 {
+			compatible = "toshiba,tmpv7708-pipllct";
+			reg = <0 0x24220000 0 0x820>;
+			#clock-cells = <1>;
+			clocks = <&osc2_clk>;
+		};
+
+		pismu: syscon@24200000 {
+			compatible = "toshiba,tmpv7708-pismu", "syscon";
+			reg = <0 0x24200000 0 0x2140>;
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+		};
+
 		uart0: serial@28200000 {
 			compatible = "arm,pl011", "arm,primecell";
 			reg = <0 0x28200000 0 0x1000>;
 			interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&uart0_pins>;
+			clocks = <&pismu TMPV770X_CLK_PIUART0>;
+			clock-names = "apb_pclk";
 			status = "disabled";
 		};
 
@@ -231,6 +207,8 @@
 			interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&uart1_pins>;
+			clocks = <&pismu TMPV770X_CLK_PIUART1>;
+			clock-names = "apb_pclk";
 			status = "disabled";
 		};
 
@@ -240,6 +218,8 @@
 			interrupts = <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&uart2_pins>;
+			clocks = <&pismu TMPV770X_CLK_PIUART2>;
+			clock-names = "apb_pclk";
 			status = "disabled";
 		};
 
@@ -249,6 +229,8 @@
 			interrupts = <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>;
 			pinctrl-names = "default";
 			pinctrl-0 = <&uart3_pins>;
+			clocks = <&pismu TMPV770X_CLK_PIUART2>;
+			clock-names = "apb_pclk";
 			status = "disabled";
 		};
 
@@ -261,6 +243,7 @@
 			clock-frequency = <400000>;
 			#address-cells = <1>;
 			#size-cells = <0>;
+			clocks = <&pismu TMPV770X_CLK_PII2C0>;
 			status = "disabled";
 		};
 
@@ -273,6 +256,7 @@
 			clock-frequency = <400000>;
 			#address-cells = <1>;
 			#size-cells = <0>;
+			clocks = <&pismu TMPV770X_CLK_PII2C1>;
 			status = "disabled";
 		};
 
@@ -285,6 +269,7 @@
 			clock-frequency = <400000>;
 			#address-cells = <1>;
 			#size-cells = <0>;
+			clocks = <&pismu TMPV770X_CLK_PII2C2>;
 			status = "disabled";
 		};
 
@@ -297,6 +282,7 @@
 			clock-frequency = <400000>;
 			#address-cells = <1>;
 			#size-cells = <0>;
+			clocks = <&pismu TMPV770X_CLK_PII2C3>;
 			status = "disabled";
 		};
 
@@ -309,6 +295,7 @@
 			clock-frequency = <400000>;
 			#address-cells = <1>;
 			#size-cells = <0>;
+			clocks = <&pismu TMPV770X_CLK_PII2C4>;
 			status = "disabled";
 		};
 
@@ -321,6 +308,7 @@
 			clock-frequency = <400000>;
 			#address-cells = <1>;
 			#size-cells = <0>;
+			clocks = <&pismu TMPV770X_CLK_PII2C5>;
 			status = "disabled";
 		};
 
@@ -333,6 +321,7 @@
 			clock-frequency = <400000>;
 			#address-cells = <1>;
 			#size-cells = <0>;
+			clocks = <&pismu TMPV770X_CLK_PII2C6>;
 			status = "disabled";
 		};
 
@@ -345,6 +334,7 @@
 			clock-frequency = <400000>;
 			#address-cells = <1>;
 			#size-cells = <0>;
+			clocks = <&pismu TMPV770X_CLK_PII2C7>;
 			status = "disabled";
 		};
 
@@ -357,6 +347,7 @@
 			clock-frequency = <400000>;
 			#address-cells = <1>;
 			#size-cells = <0>;
+			clocks = <&pismu TMPV770X_CLK_PII2C8>;
 			status = "disabled";
 		};
 
@@ -369,6 +360,8 @@
 			num-cs = <1>;
 			#address-cells = <1>;
 			#size-cells = <0>;
+			clocks = <&pismu TMPV770X_CLK_PISPI1>;
+			clock-names = "apb_pclk";
 			status = "disabled";
 		};
 
@@ -381,6 +374,8 @@
 			num-cs = <1>;
 			#address-cells = <1>;
 			#size-cells = <0>;
+			clocks = <&pismu TMPV770X_CLK_PISPI1>;
+			clock-names = "apb_pclk";
 			status = "disabled";
 		};
 
@@ -393,6 +388,8 @@
 			num-cs = <1>;
 			#address-cells = <1>;
 			#size-cells = <0>;
+			clocks = <&pismu TMPV770X_CLK_PISPI2>;
+			clock-names = "apb_pclk";
 			status = "disabled";
 		};
 
@@ -405,6 +402,8 @@
 			num-cs = <1>;
 			#address-cells = <1>;
 			#size-cells = <0>;
+			clocks = <&pismu TMPV770X_CLK_PISPI3>;
+			clock-names = "apb_pclk";
 			status = "disabled";
 		};
 
@@ -417,6 +416,8 @@
 			num-cs = <1>;
 			#address-cells = <1>;
 			#size-cells = <0>;
+			clocks = <&pismu TMPV770X_CLK_PISPI4>;
+			clock-names = "apb_pclk";
 			status = "disabled";
 		};
 
@@ -429,6 +430,8 @@
 			num-cs = <1>;
 			#address-cells = <1>;
 			#size-cells = <0>;
+			clocks = <&pismu TMPV770X_CLK_PISPI5>;
+			clock-names = "apb_pclk";
 			status = "disabled";
 		};
 
@@ -441,6 +444,8 @@
 			num-cs = <1>;
 			#address-cells = <1>;
 			#size-cells = <0>;
+			clocks = <&pismu TMPV770X_CLK_PISPI6>;
+			clock-names = "apb_pclk";
 			status = "disabled";
 		};
 
@@ -452,12 +457,15 @@
 			snps,txpbl = <4>;
 			snps,rxpbl = <4>;
 			snps,tso;
+			clocks = <&pismu TMPV770X_CLK_PIETHER_BUS>, <&pismu TMPV770X_CLK_PIETHER_125M>;
+			clock-names = "stmmaceth", "phy_ref_clk";
 			status = "disabled";
 		};
 
 		wdt: wdt@28330000 {
 			compatible = "toshiba,visconti-wdt";
 			reg = <0 0x28330000 0 0x1000>;
+			clocks = <&pismu TMPV770X_CLK_WDTCLK>;
 			status = "disabled";
 		};
 
@@ -498,6 +506,8 @@
 				 0 0 0 3 &gic GIC_SPI 215 IRQ_TYPE_LEVEL_HIGH
 				 0 0 0 4 &gic GIC_SPI 215 IRQ_TYPE_LEVEL_HIGH>;
 			max-link-speed = <2>;
+			clocks = <&extclk100mhz>, <&pismu TMPV770X_CLK_PCIE_MSTR>, <&pismu TMPV770X_CLK_PCIE_AUX>;
+			clock-names = "ref", "core", "aux";
 			status = "disabled";
 		};
 	};
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-clk-ccf.dtsi b/arch/arm64/boot/dts/xilinx/zynqmp-clk-ccf.dtsi
index 1e0b1bca7c94..e172fa05c9a0 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp-clk-ccf.dtsi
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-clk-ccf.dtsi
@@ -223,11 +223,11 @@
 	clocks = <&zynqmp_clk UART1_REF>, <&zynqmp_clk LPD_LSBUS>;
 };
 
-&usb0 {
+&dwc3_0 {
 	clocks = <&zynqmp_clk USB0_BUS_REF>, <&zynqmp_clk USB3_DUAL_REF>;
 };
 
-&usb1 {
+&dwc3_1 {
 	clocks = <&zynqmp_clk USB1_BUS_REF>, <&zynqmp_clk USB3_DUAL_REF>;
 };
 
@@ -239,6 +239,10 @@
 	clocks = <&zynqmp_clk LPD_WDT>;
 };
 
+&xilinx_ams {
+	clocks = <&zynqmp_clk AMS_REF>;
+};
+
 &zynqmp_dpdma {
 	clocks = <&zynqmp_clk DPDMA_REF>;
 };
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-sm-k26-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-sm-k26-revA.dts
index 550b389153e6..20e83ca47b5d 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp-sm-k26-revA.dts
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-sm-k26-revA.dts
@@ -52,7 +52,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 		autorepeat;
-		fwuen {
+		key-fwuen {
 			label = "fwuen";
 			gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
 		};
@@ -285,5 +285,5 @@
 			  "", "", "", "", "", /* 155 - 159 */
 			  "", "", "", "", "", /* 160 - 164 */
 			  "", "", "", "", "", /* 165 - 169 */
-			  "", "", "", ""; /* 170 - 174 */
+			  "", "", "", ""; /* 170 - 173 */
 };
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu100-revC.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu100-revC.dts
index f6aad4159ccd..d61a297a2090 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu100-revC.dts
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu100-revC.dts
@@ -49,7 +49,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 		autorepeat;
-		sw4 {
+		switch-4 {
 			label = "sw4";
 			gpios = <&gpio 23 GPIO_ACTIVE_LOW>;
 			linux,code = <KEY_POWER>;
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts
index 7b9a88b125d1..5fd6b70a154a 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu102-revA.dts
@@ -47,7 +47,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 		autorepeat;
-		sw19 {
+		switch-19 {
 			label = "sw19";
 			gpios = <&gpio 22 GPIO_ACTIVE_HIGH>;
 			linux,code = <KEY_DOWN>;
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts
index 20b7c75bb1d3..e2dd72fe33ce 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu106-revA.dts
@@ -47,7 +47,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 		autorepeat;
-		sw19 {
+		switch-19 {
 			label = "sw19";
 			gpios = <&gpio 22 GPIO_ACTIVE_HIGH>;
 			linux,code = <KEY_DOWN>;
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts
index e36df6adbeee..d685d8fbc36a 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu111-revA.dts
@@ -47,7 +47,7 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 		autorepeat;
-		sw19 {
+		switch-19 {
 			label = "sw19";
 			gpios = <&gpio 22 GPIO_ACTIVE_HIGH>;
 			linux,code = <KEY_DOWN>;
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp.dtsi b/arch/arm64/boot/dts/xilinx/zynqmp.dtsi
index 74e66443e4ce..a549265e55f6 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp.dtsi
+++ b/arch/arm64/boot/dts/xilinx/zynqmp.dtsi
@@ -254,106 +254,106 @@
 		};
 
 		/* GDMA */
-		fpd_dma_chan1: dma@fd500000 {
+		fpd_dma_chan1: dma-controller@fd500000 {
 			status = "disabled";
 			compatible = "xlnx,zynqmp-dma-1.0";
 			reg = <0x0 0xfd500000 0x0 0x1000>;
 			interrupt-parent = <&gic>;
 			interrupts = <0 124 4>;
 			clock-names = "clk_main", "clk_apb";
+			#dma-cells = <1>;
 			xlnx,bus-width = <128>;
-			#stream-id-cells = <1>;
 			iommus = <&smmu 0x14e8>;
 			power-domains = <&zynqmp_firmware PD_GDMA>;
 		};
 
-		fpd_dma_chan2: dma@fd510000 {
+		fpd_dma_chan2: dma-controller@fd510000 {
 			status = "disabled";
 			compatible = "xlnx,zynqmp-dma-1.0";
 			reg = <0x0 0xfd510000 0x0 0x1000>;
 			interrupt-parent = <&gic>;
 			interrupts = <0 125 4>;
 			clock-names = "clk_main", "clk_apb";
+			#dma-cells = <1>;
 			xlnx,bus-width = <128>;
-			#stream-id-cells = <1>;
 			iommus = <&smmu 0x14e9>;
 			power-domains = <&zynqmp_firmware PD_GDMA>;
 		};
 
-		fpd_dma_chan3: dma@fd520000 {
+		fpd_dma_chan3: dma-controller@fd520000 {
 			status = "disabled";
 			compatible = "xlnx,zynqmp-dma-1.0";
 			reg = <0x0 0xfd520000 0x0 0x1000>;
 			interrupt-parent = <&gic>;
 			interrupts = <0 126 4>;
 			clock-names = "clk_main", "clk_apb";
+			#dma-cells = <1>;
 			xlnx,bus-width = <128>;
-			#stream-id-cells = <1>;
 			iommus = <&smmu 0x14ea>;
 			power-domains = <&zynqmp_firmware PD_GDMA>;
 		};
 
-		fpd_dma_chan4: dma@fd530000 {
+		fpd_dma_chan4: dma-controller@fd530000 {
 			status = "disabled";
 			compatible = "xlnx,zynqmp-dma-1.0";
 			reg = <0x0 0xfd530000 0x0 0x1000>;
 			interrupt-parent = <&gic>;
 			interrupts = <0 127 4>;
 			clock-names = "clk_main", "clk_apb";
+			#dma-cells = <1>;
 			xlnx,bus-width = <128>;
-			#stream-id-cells = <1>;
 			iommus = <&smmu 0x14eb>;
 			power-domains = <&zynqmp_firmware PD_GDMA>;
 		};
 
-		fpd_dma_chan5: dma@fd540000 {
+		fpd_dma_chan5: dma-controller@fd540000 {
 			status = "disabled";
 			compatible = "xlnx,zynqmp-dma-1.0";
 			reg = <0x0 0xfd540000 0x0 0x1000>;
 			interrupt-parent = <&gic>;
 			interrupts = <0 128 4>;
 			clock-names = "clk_main", "clk_apb";
+			#dma-cells = <1>;
 			xlnx,bus-width = <128>;
-			#stream-id-cells = <1>;
 			iommus = <&smmu 0x14ec>;
 			power-domains = <&zynqmp_firmware PD_GDMA>;
 		};
 
-		fpd_dma_chan6: dma@fd550000 {
+		fpd_dma_chan6: dma-controller@fd550000 {
 			status = "disabled";
 			compatible = "xlnx,zynqmp-dma-1.0";
 			reg = <0x0 0xfd550000 0x0 0x1000>;
 			interrupt-parent = <&gic>;
 			interrupts = <0 129 4>;
 			clock-names = "clk_main", "clk_apb";
+			#dma-cells = <1>;
 			xlnx,bus-width = <128>;
-			#stream-id-cells = <1>;
 			iommus = <&smmu 0x14ed>;
 			power-domains = <&zynqmp_firmware PD_GDMA>;
 		};
 
-		fpd_dma_chan7: dma@fd560000 {
+		fpd_dma_chan7: dma-controller@fd560000 {
 			status = "disabled";
 			compatible = "xlnx,zynqmp-dma-1.0";
 			reg = <0x0 0xfd560000 0x0 0x1000>;
 			interrupt-parent = <&gic>;
 			interrupts = <0 130 4>;
 			clock-names = "clk_main", "clk_apb";
+			#dma-cells = <1>;
 			xlnx,bus-width = <128>;
-			#stream-id-cells = <1>;
 			iommus = <&smmu 0x14ee>;
 			power-domains = <&zynqmp_firmware PD_GDMA>;
 		};
 
-		fpd_dma_chan8: dma@fd570000 {
+		fpd_dma_chan8: dma-controller@fd570000 {
 			status = "disabled";
 			compatible = "xlnx,zynqmp-dma-1.0";
 			reg = <0x0 0xfd570000 0x0 0x1000>;
 			interrupt-parent = <&gic>;
 			interrupts = <0 131 4>;
 			clock-names = "clk_main", "clk_apb";
+			#dma-cells = <1>;
 			xlnx,bus-width = <128>;
-			#stream-id-cells = <1>;
 			iommus = <&smmu 0x14ef>;
 			power-domains = <&zynqmp_firmware PD_GDMA>;
 		};
@@ -375,106 +375,106 @@
 		 * These dma channels, Users should ensure that these dma
 		 * Channels are allowed for non secure access.
 		 */
-		lpd_dma_chan1: dma@ffa80000 {
+		lpd_dma_chan1: dma-controller@ffa80000 {
 			status = "disabled";
 			compatible = "xlnx,zynqmp-dma-1.0";
 			reg = <0x0 0xffa80000 0x0 0x1000>;
 			interrupt-parent = <&gic>;
 			interrupts = <0 77 4>;
 			clock-names = "clk_main", "clk_apb";
+			#dma-cells = <1>;
 			xlnx,bus-width = <64>;
-			#stream-id-cells = <1>;
 			iommus = <&smmu 0x868>;
 			power-domains = <&zynqmp_firmware PD_ADMA>;
 		};
 
-		lpd_dma_chan2: dma@ffa90000 {
+		lpd_dma_chan2: dma-controller@ffa90000 {
 			status = "disabled";
 			compatible = "xlnx,zynqmp-dma-1.0";
 			reg = <0x0 0xffa90000 0x0 0x1000>;
 			interrupt-parent = <&gic>;
 			interrupts = <0 78 4>;
 			clock-names = "clk_main", "clk_apb";
+			#dma-cells = <1>;
 			xlnx,bus-width = <64>;
-			#stream-id-cells = <1>;
 			iommus = <&smmu 0x869>;
 			power-domains = <&zynqmp_firmware PD_ADMA>;
 		};
 
-		lpd_dma_chan3: dma@ffaa0000 {
+		lpd_dma_chan3: dma-controller@ffaa0000 {
 			status = "disabled";
 			compatible = "xlnx,zynqmp-dma-1.0";
 			reg = <0x0 0xffaa0000 0x0 0x1000>;
 			interrupt-parent = <&gic>;
 			interrupts = <0 79 4>;
 			clock-names = "clk_main", "clk_apb";
+			#dma-cells = <1>;
 			xlnx,bus-width = <64>;
-			#stream-id-cells = <1>;
 			iommus = <&smmu 0x86a>;
 			power-domains = <&zynqmp_firmware PD_ADMA>;
 		};
 
-		lpd_dma_chan4: dma@ffab0000 {
+		lpd_dma_chan4: dma-controller@ffab0000 {
 			status = "disabled";
 			compatible = "xlnx,zynqmp-dma-1.0";
 			reg = <0x0 0xffab0000 0x0 0x1000>;
 			interrupt-parent = <&gic>;
 			interrupts = <0 80 4>;
 			clock-names = "clk_main", "clk_apb";
+			#dma-cells = <1>;
 			xlnx,bus-width = <64>;
-			#stream-id-cells = <1>;
 			iommus = <&smmu 0x86b>;
 			power-domains = <&zynqmp_firmware PD_ADMA>;
 		};
 
-		lpd_dma_chan5: dma@ffac0000 {
+		lpd_dma_chan5: dma-controller@ffac0000 {
 			status = "disabled";
 			compatible = "xlnx,zynqmp-dma-1.0";
 			reg = <0x0 0xffac0000 0x0 0x1000>;
 			interrupt-parent = <&gic>;
 			interrupts = <0 81 4>;
 			clock-names = "clk_main", "clk_apb";
+			#dma-cells = <1>;
 			xlnx,bus-width = <64>;
-			#stream-id-cells = <1>;
 			iommus = <&smmu 0x86c>;
 			power-domains = <&zynqmp_firmware PD_ADMA>;
 		};
 
-		lpd_dma_chan6: dma@ffad0000 {
+		lpd_dma_chan6: dma-controller@ffad0000 {
 			status = "disabled";
 			compatible = "xlnx,zynqmp-dma-1.0";
 			reg = <0x0 0xffad0000 0x0 0x1000>;
 			interrupt-parent = <&gic>;
 			interrupts = <0 82 4>;
 			clock-names = "clk_main", "clk_apb";
+			#dma-cells = <1>;
 			xlnx,bus-width = <64>;
-			#stream-id-cells = <1>;
 			iommus = <&smmu 0x86d>;
 			power-domains = <&zynqmp_firmware PD_ADMA>;
 		};
 
-		lpd_dma_chan7: dma@ffae0000 {
+		lpd_dma_chan7: dma-controller@ffae0000 {
 			status = "disabled";
 			compatible = "xlnx,zynqmp-dma-1.0";
 			reg = <0x0 0xffae0000 0x0 0x1000>;
 			interrupt-parent = <&gic>;
 			interrupts = <0 83 4>;
 			clock-names = "clk_main", "clk_apb";
+			#dma-cells = <1>;
 			xlnx,bus-width = <64>;
-			#stream-id-cells = <1>;
 			iommus = <&smmu 0x86e>;
 			power-domains = <&zynqmp_firmware PD_ADMA>;
 		};
 
-		lpd_dma_chan8: dma@ffaf0000 {
+		lpd_dma_chan8: dma-controller@ffaf0000 {
 			status = "disabled";
 			compatible = "xlnx,zynqmp-dma-1.0";
 			reg = <0x0 0xffaf0000 0x0 0x1000>;
 			interrupt-parent = <&gic>;
 			interrupts = <0 84 4>;
 			clock-names = "clk_main", "clk_apb";
+			#dma-cells = <1>;
 			xlnx,bus-width = <64>;
-			#stream-id-cells = <1>;
 			iommus = <&smmu 0x86f>;
 			power-domains = <&zynqmp_firmware PD_ADMA>;
 		};
@@ -495,7 +495,6 @@
 			interrupts = <0 14 4>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			#stream-id-cells = <1>;
 			iommus = <&smmu 0x872>;
 			power-domains = <&zynqmp_firmware PD_NAND>;
 		};
@@ -509,9 +508,10 @@
 			clock-names = "pclk", "hclk", "tx_clk";
 			#address-cells = <1>;
 			#size-cells = <0>;
-			#stream-id-cells = <1>;
 			iommus = <&smmu 0x874>;
 			power-domains = <&zynqmp_firmware PD_ETH_0>;
+			resets = <&zynqmp_reset ZYNQMP_RESET_GEM0>;
+			reset-names = "gem0_rst";
 		};
 
 		gem1: ethernet@ff0c0000 {
@@ -523,9 +523,10 @@
 			clock-names = "pclk", "hclk", "tx_clk";
 			#address-cells = <1>;
 			#size-cells = <0>;
-			#stream-id-cells = <1>;
 			iommus = <&smmu 0x875>;
 			power-domains = <&zynqmp_firmware PD_ETH_1>;
+			resets = <&zynqmp_reset ZYNQMP_RESET_GEM1>;
+			reset-names = "gem1_rst";
 		};
 
 		gem2: ethernet@ff0d0000 {
@@ -537,9 +538,10 @@
 			clock-names = "pclk", "hclk", "tx_clk";
 			#address-cells = <1>;
 			#size-cells = <0>;
-			#stream-id-cells = <1>;
 			iommus = <&smmu 0x876>;
 			power-domains = <&zynqmp_firmware PD_ETH_2>;
+			resets = <&zynqmp_reset ZYNQMP_RESET_GEM2>;
+			reset-names = "gem2_rst";
 		};
 
 		gem3: ethernet@ff0e0000 {
@@ -551,9 +553,10 @@
 			clock-names = "pclk", "hclk", "tx_clk";
 			#address-cells = <1>;
 			#size-cells = <0>;
-			#stream-id-cells = <1>;
 			iommus = <&smmu 0x877>;
 			power-domains = <&zynqmp_firmware PD_ETH_3>;
+			resets = <&zynqmp_reset ZYNQMP_RESET_GEM3>;
+			reset-names = "gem3_rst";
 		};
 
 		gpio: gpio@ff0a0000 {
@@ -621,7 +624,6 @@
 					<0x0 0x0 0x0 0x2 &pcie_intc 0x2>,
 					<0x0 0x0 0x0 0x3 &pcie_intc 0x3>,
 					<0x0 0x0 0x0 0x4 &pcie_intc 0x4>;
-			#stream-id-cells = <1>;
 			iommus = <&smmu 0x4d0>;
 			power-domains = <&zynqmp_firmware PD_PCIE>;
 			pcie_intc: legacy-interrupt-controller {
@@ -642,7 +644,6 @@
 			      <0x0 0xc0000000 0x0 0x8000000>;
 			#address-cells = <1>;
 			#size-cells = <0>;
-			#stream-id-cells = <1>;
 			iommus = <&smmu 0x873>;
 			power-domains = <&zynqmp_firmware PD_QSPI>;
 		};
@@ -674,7 +675,6 @@
 			interrupts = <0 133 4>;
 			power-domains = <&zynqmp_firmware PD_SATA>;
 			resets = <&zynqmp_reset ZYNQMP_RESET_SATA>;
-			#stream-id-cells = <4>;
 			iommus = <&smmu 0x4c0>, <&smmu 0x4c1>,
 				 <&smmu 0x4c2>, <&smmu 0x4c3>;
 		};
@@ -686,7 +686,6 @@
 			interrupts = <0 48 4>;
 			reg = <0x0 0xff160000 0x0 0x1000>;
 			clock-names = "clk_xin", "clk_ahb";
-			#stream-id-cells = <1>;
 			iommus = <&smmu 0x870>;
 			#clock-cells = <1>;
 			clock-output-names = "clk_out_sd0", "clk_in_sd0";
@@ -700,7 +699,6 @@
 			interrupts = <0 49 4>;
 			reg = <0x0 0xff170000 0x0 0x1000>;
 			clock-names = "clk_xin", "clk_ahb";
-			#stream-id-cells = <1>;
 			iommus = <&smmu 0x871>;
 			#clock-cells = <1>;
 			clock-output-names = "clk_out_sd1", "clk_in_sd1";
@@ -811,7 +809,6 @@
 			status = "disabled";
 			compatible = "xlnx,zynqmp-dwc3";
 			reg = <0x0 0xff9d0000 0x0 0x100>;
-			clock-names = "bus_clk", "ref_clk";
 			power-domains = <&zynqmp_firmware PD_USB_0>;
 			resets = <&zynqmp_reset ZYNQMP_RESET_USB0_CORERESET>,
 				 <&zynqmp_reset ZYNQMP_RESET_USB0_HIBERRESET>,
@@ -825,7 +822,7 @@
 				interrupt-parent = <&gic>;
 				interrupt-names = "dwc_usb3", "otg";
 				interrupts = <0 65 4>, <0 69 4>;
-				#stream-id-cells = <1>;
+				clock-names = "bus_early", "ref";
 				iommus = <&smmu 0x860>;
 				snps,quirk-frame-length-adjustment = <0x20>;
 				/* dma-coherent; */
@@ -838,7 +835,6 @@
 			status = "disabled";
 			compatible = "xlnx,zynqmp-dwc3";
 			reg = <0x0 0xff9e0000 0x0 0x100>;
-			clock-names = "bus_clk", "ref_clk";
 			power-domains = <&zynqmp_firmware PD_USB_1>;
 			resets = <&zynqmp_reset ZYNQMP_RESET_USB1_CORERESET>,
 				 <&zynqmp_reset ZYNQMP_RESET_USB1_HIBERRESET>,
@@ -852,7 +848,7 @@
 				interrupt-parent = <&gic>;
 				interrupt-names = "dwc_usb3", "otg";
 				interrupts = <0 70 4>, <0 74 4>;
-				#stream-id-cells = <1>;
+				clock-names = "bus_early", "ref";
 				iommus = <&smmu 0x861>;
 				snps,quirk-frame-length-adjustment = <0x20>;
 				/* dma-coherent; */
@@ -878,6 +874,32 @@
 			timeout-sec = <10>;
 		};
 
+		xilinx_ams: ams@ffa50000 {
+			compatible = "xlnx,zynqmp-ams";
+			status = "disabled";
+			interrupt-parent = <&gic>;
+			interrupts = <0 56 4>;
+			reg = <0x0 0xffa50000 0x0 0x800>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			#io-channel-cells = <1>;
+			ranges = <0 0 0xffa50800 0x800>;
+
+			ams_ps: ams_ps@0 {
+				compatible = "xlnx,zynqmp-ams-ps";
+				status = "disabled";
+				reg = <0x0 0x400>;
+			};
+
+			ams_pl: ams_pl@400 {
+				compatible = "xlnx,zynqmp-ams-pl";
+				status = "disabled";
+				reg = <0x400 0x400>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
+
 		zynqmp_dpdma: dma-controller@fd4c0000 {
 			compatible = "xlnx,zynqmp-dpdma";
 			status = "disabled";
diff --git a/arch/arm64/boot/install.sh b/arch/arm64/boot/install.sh
index d91e1f022573..7399d706967a 100644..100755
--- a/arch/arm64/boot/install.sh
+++ b/arch/arm64/boot/install.sh
@@ -1,7 +1,5 @@
 #!/bin/sh
 #
-# arch/arm64/boot/install.sh
-#
 # This file is subject to the terms and conditions of the GNU General Public
 # License.  See the file "COPYING" in the main directory of this archive
 # for more details.
@@ -18,25 +16,6 @@
 #   $2 - kernel image file
 #   $3 - kernel map file
 #   $4 - default install path (blank if root directory)
-#
-
-verify () {
-	if [ ! -f "$1" ]; then
-		echo ""                                                   1>&2
-		echo " *** Missing file: $1"                              1>&2
-		echo ' *** You need to run "make" before "make install".' 1>&2
-		echo ""                                                   1>&2
-		exit 1
-	fi
-}
-
-# Make sure the files actually exist
-verify "$2"
-verify "$3"
-
-# User may have a custom install script
-if [ -x ~/bin/${INSTALLKERNEL} ]; then exec ~/bin/${INSTALLKERNEL} "$@"; fi
-if [ -x /sbin/${INSTALLKERNEL} ]; then exec /sbin/${INSTALLKERNEL} "$@"; fi
 
 if [ "$(basename $2)" = "Image.gz" ]; then
 # Compressed install
diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig
index f2e2b9bdd702..0b6af3348e79 100644
--- a/arch/arm64/configs/defconfig
+++ b/arch/arm64/configs/defconfig
@@ -3,36 +3,40 @@ CONFIG_POSIX_MQUEUE=y
 CONFIG_AUDIT=y
 CONFIG_NO_HZ_IDLE=y
 CONFIG_HIGH_RES_TIMERS=y
+CONFIG_BPF_SYSCALL=y
+CONFIG_BPF_JIT=y
 CONFIG_PREEMPT=y
 CONFIG_IRQ_TIME_ACCOUNTING=y
 CONFIG_BSD_PROCESS_ACCT=y
 CONFIG_BSD_PROCESS_ACCT_V3=y
+CONFIG_TASKSTATS=y
 CONFIG_TASK_XACCT=y
 CONFIG_TASK_IO_ACCOUNTING=y
 CONFIG_IKCONFIG=y
 CONFIG_IKCONFIG_PROC=y
 CONFIG_NUMA_BALANCING=y
 CONFIG_MEMCG=y
-CONFIG_MEMCG_SWAP=y
 CONFIG_BLK_CGROUP=y
 CONFIG_CGROUP_PIDS=y
+CONFIG_CGROUP_FREEZER=y
 CONFIG_CGROUP_HUGETLB=y
 CONFIG_CPUSETS=y
 CONFIG_CGROUP_DEVICE=y
 CONFIG_CGROUP_CPUACCT=y
 CONFIG_CGROUP_PERF=y
+CONFIG_CGROUP_BPF=y
 CONFIG_USER_NS=y
 CONFIG_SCHED_AUTOGROUP=y
 CONFIG_BLK_DEV_INITRD=y
 CONFIG_KALLSYMS_ALL=y
-# CONFIG_COMPAT_BRK is not set
 CONFIG_PROFILING=y
 CONFIG_ARCH_ACTIONS=y
 CONFIG_ARCH_SUNXI=y
 CONFIG_ARCH_ALPINE=y
 CONFIG_ARCH_APPLE=y
+CONFIG_ARCH_BCM=y
 CONFIG_ARCH_BCM2835=y
-CONFIG_ARCH_BCM4908=y
+CONFIG_ARCH_BCMBCA=y
 CONFIG_ARCH_BCM_IPROC=y
 CONFIG_ARCH_BERLIN=y
 CONFIG_ARCH_BRCMSTB=y
@@ -45,7 +49,9 @@ CONFIG_ARCH_KEEMBAY=y
 CONFIG_ARCH_MEDIATEK=y
 CONFIG_ARCH_MESON=y
 CONFIG_ARCH_MVEBU=y
+CONFIG_ARCH_NXP=y
 CONFIG_ARCH_MXC=y
+CONFIG_ARCH_NPCM=y
 CONFIG_ARCH_QCOM=y
 CONFIG_ARCH_RENESAS=y
 CONFIG_ARCH_ROCKCHIP=y
@@ -54,6 +60,7 @@ CONFIG_ARCH_SEATTLE=y
 CONFIG_ARCH_INTEL_SOCFPGA=y
 CONFIG_ARCH_SYNQUACER=y
 CONFIG_ARCH_TEGRA=y
+CONFIG_ARCH_TESLA_FSD=y
 CONFIG_ARCH_SPRD=y
 CONFIG_ARCH_THUNDER=y
 CONFIG_ARCH_THUNDER2=y
@@ -66,7 +73,6 @@ CONFIG_ARM64_VA_BITS_48=y
 CONFIG_SCHED_MC=y
 CONFIG_SCHED_SMT=y
 CONFIG_NUMA=y
-CONFIG_SECCOMP=y
 CONFIG_KEXEC=y
 CONFIG_KEXEC_FILE=y
 CONFIG_CRASH_DUMP=y
@@ -76,7 +82,6 @@ CONFIG_RANDOMIZE_BASE=y
 CONFIG_HIBERNATION=y
 CONFIG_WQ_POWER_EFFICIENT_DEFAULT=y
 CONFIG_ENERGY_MODEL=y
-CONFIG_ARM_CPUIDLE=y
 CONFIG_ARM_PSCI_CPUIDLE=y
 CONFIG_CPU_FREQ=y
 CONFIG_CPU_FREQ_STAT=y
@@ -84,29 +89,22 @@ CONFIG_CPU_FREQ_GOV_POWERSAVE=m
 CONFIG_CPU_FREQ_GOV_USERSPACE=y
 CONFIG_CPU_FREQ_GOV_ONDEMAND=y
 CONFIG_CPU_FREQ_GOV_CONSERVATIVE=m
-CONFIG_CPU_FREQ_GOV_SCHEDUTIL=y
 CONFIG_CPUFREQ_DT=y
 CONFIG_ACPI_CPPC_CPUFREQ=m
 CONFIG_ARM_ALLWINNER_SUN50I_CPUFREQ_NVMEM=m
 CONFIG_ARM_ARMADA_37XX_CPUFREQ=y
 CONFIG_ARM_SCPI_CPUFREQ=y
 CONFIG_ARM_IMX_CPUFREQ_DT=m
+CONFIG_ARM_MEDIATEK_CPUFREQ=y
 CONFIG_ARM_QCOM_CPUFREQ_NVMEM=y
 CONFIG_ARM_QCOM_CPUFREQ_HW=y
 CONFIG_ARM_RASPBERRYPI_CPUFREQ=m
 CONFIG_ARM_SCMI_CPUFREQ=y
 CONFIG_ARM_TEGRA186_CPUFREQ=y
 CONFIG_QORIQ_CPUFREQ=y
-CONFIG_ARM_SCMI_PROTOCOL=y
-CONFIG_ARM_SCPI_PROTOCOL=y
-CONFIG_RASPBERRYPI_FIRMWARE=y
-CONFIG_INTEL_STRATIX10_SERVICE=y
-CONFIG_INTEL_STRATIX10_RSU=m
-CONFIG_QCOM_SCM=y
-CONFIG_EFI_CAPSULE_LOADER=y
-CONFIG_IMX_SCU=y
-CONFIG_IMX_SCU_PD=y
 CONFIG_ACPI=y
+CONFIG_ACPI_HOTPLUG_MEMORY=y
+CONFIG_ACPI_HMAT=y
 CONFIG_ACPI_APEI=y
 CONFIG_ACPI_APEI_GHES=y
 CONFIG_ACPI_APEI_PCIEAER=y
@@ -114,7 +112,6 @@ CONFIG_ACPI_APEI_MEMORY_FAILURE=y
 CONFIG_ACPI_APEI_EINJ=y
 CONFIG_VIRTUALIZATION=y
 CONFIG_KVM=y
-CONFIG_ARM64_CRYPTO=y
 CONFIG_CRYPTO_SHA1_ARM64_CE=y
 CONFIG_CRYPTO_SHA2_ARM64_CE=y
 CONFIG_CRYPTO_SHA512_ARM64_CE=m
@@ -130,6 +127,9 @@ CONFIG_JUMP_LABEL=y
 CONFIG_MODULES=y
 CONFIG_MODULE_UNLOAD=y
 # CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+# CONFIG_COMPAT_BRK is not set
+CONFIG_MEMORY_HOTPLUG=y
+CONFIG_MEMORY_HOTREMOVE=y
 CONFIG_KSM=y
 CONFIG_MEMORY_FAILURE=y
 CONFIG_TRANSPARENT_HUGEPAGE=y
@@ -143,12 +143,16 @@ CONFIG_IP_PNP_DHCP=y
 CONFIG_IP_PNP_BOOTP=y
 CONFIG_IPV6=m
 CONFIG_NETFILTER=y
+CONFIG_BRIDGE_NETFILTER=m
 CONFIG_NF_CONNTRACK=m
 CONFIG_NF_CONNTRACK_EVENTS=y
+CONFIG_NETFILTER_XT_MARK=m
 CONFIG_NETFILTER_XT_TARGET_CHECKSUM=m
 CONFIG_NETFILTER_XT_TARGET_LOG=m
 CONFIG_NETFILTER_XT_MATCH_ADDRTYPE=m
 CONFIG_NETFILTER_XT_MATCH_CONNTRACK=m
+CONFIG_NETFILTER_XT_MATCH_IPVS=m
+CONFIG_IP_VS=m
 CONFIG_IP_NF_IPTABLES=m
 CONFIG_IP_NF_FILTER=m
 CONFIG_IP_NF_TARGET_REJECT=m
@@ -179,17 +183,15 @@ CONFIG_NET_CLS_ACT=y
 CONFIG_NET_ACT_GACT=m
 CONFIG_NET_ACT_MIRRED=m
 CONFIG_NET_ACT_GATE=m
-CONFIG_QRTR=m
 CONFIG_QRTR_SMD=m
 CONFIG_QRTR_TUN=m
-CONFIG_BPF_JIT=y
 CONFIG_CAN=m
+CONFIG_CAN_FLEXCAN=m
 CONFIG_CAN_RCAR=m
 CONFIG_CAN_RCAR_CANFD=m
-CONFIG_CAN_FLEXCAN=m
+CONFIG_CAN_MCP251XFD=m
 CONFIG_BT=m
 CONFIG_BT_HIDP=m
-# CONFIG_BT_HS is not set
 # CONFIG_BT_LE is not set
 CONFIG_BT_LEDS=y
 # CONFIG_BT_DEBUGFS is not set
@@ -198,6 +200,9 @@ CONFIG_BT_HCIUART=m
 CONFIG_BT_HCIUART_LL=y
 CONFIG_BT_HCIUART_BCM=y
 CONFIG_BT_HCIUART_QCA=y
+CONFIG_BT_HCIUART_MRVL=y
+CONFIG_BT_MRVL=m
+CONFIG_BT_MRVL_SDIO=m
 CONFIG_BT_QCOMSMD=m
 CONFIG_CFG80211=m
 CONFIG_MAC80211=m
@@ -210,6 +215,7 @@ CONFIG_NFC_NCI=m
 CONFIG_NFC_S3FWRN5_I2C=m
 CONFIG_PCI=y
 CONFIG_PCIEPORTBUS=y
+CONFIG_PCIEAER=y
 CONFIG_PCI_IOV=y
 CONFIG_PCI_PASID=y
 CONFIG_HOTPLUG_PCI=y
@@ -228,7 +234,6 @@ CONFIG_PCIE_ROCKCHIP_HOST=m
 CONFIG_PCIE_BRCMSTB=m
 CONFIG_PCI_IMX6=y
 CONFIG_PCI_LAYERSCAPE=y
-CONFIG_PCIE_LAYERSCAPE_GEN4=y
 CONFIG_PCI_HISI=y
 CONFIG_PCIE_QCOM=y
 CONFIG_PCIE_ARMADA_8K=y
@@ -236,6 +241,7 @@ CONFIG_PCIE_KIRIN=y
 CONFIG_PCIE_HISI_STB=y
 CONFIG_PCIE_TEGRA194_HOST=m
 CONFIG_PCIE_VISCONTI_HOST=y
+CONFIG_PCIE_LAYERSCAPE_GEN4=y
 CONFIG_PCI_ENDPOINT=y
 CONFIG_PCI_ENDPOINT_CONFIGFS=y
 CONFIG_PCI_EPF_TEST=m
@@ -243,8 +249,15 @@ CONFIG_DEVTMPFS=y
 CONFIG_DEVTMPFS_MOUNT=y
 CONFIG_FW_LOADER_USER_HELPER=y
 CONFIG_HISILICON_LPC=y
-CONFIG_FSL_MC_BUS=y
 CONFIG_TEGRA_ACONNECT=m
+CONFIG_ARM_SCMI_PROTOCOL=y
+CONFIG_ARM_SCPI_PROTOCOL=y
+CONFIG_RASPBERRYPI_FIRMWARE=y
+CONFIG_INTEL_STRATIX10_SERVICE=y
+CONFIG_INTEL_STRATIX10_RSU=m
+CONFIG_EFI_CAPSULE_LOADER=y
+CONFIG_IMX_SCU=y
+CONFIG_IMX_SCU_PD=y
 CONFIG_GNSS=m
 CONFIG_GNSS_MTK_SERIAL=m
 CONFIG_MTD=y
@@ -261,15 +274,16 @@ CONFIG_MTD_SST25L=y
 CONFIG_MTD_RAW_NAND=y
 CONFIG_MTD_NAND_DENALI_DT=y
 CONFIG_MTD_NAND_MARVELL=y
+CONFIG_MTD_NAND_BRCMNAND=m
 CONFIG_MTD_NAND_FSL_IFC=y
 CONFIG_MTD_NAND_QCOM=y
 CONFIG_MTD_SPI_NOR=y
-CONFIG_MTK_DEVAPC=m
-CONFIG_SPI_CADENCE_QUADSPI=y
 CONFIG_BLK_DEV_LOOP=y
 CONFIG_BLK_DEV_NBD=m
 CONFIG_VIRTIO_BLK=y
 CONFIG_BLK_DEV_NVME=m
+CONFIG_QCOM_COINCELL=m
+CONFIG_QCOM_FASTRPC=m
 CONFIG_SRAM=y
 CONFIG_PCI_ENDPOINT_TEST=m
 CONFIG_EEPROM_AT24=m
@@ -282,14 +296,10 @@ CONFIG_SCSI_HISI_SAS=y
 CONFIG_SCSI_HISI_SAS_PCI=y
 CONFIG_MEGARAID_SAS=y
 CONFIG_SCSI_MPT3SAS=m
-CONFIG_SCSI_UFSHCD=y
-CONFIG_SCSI_UFSHCD_PLATFORM=y
-CONFIG_SCSI_UFS_QCOM=m
-CONFIG_SCSI_UFS_HISI=y
-CONFIG_SCSI_UFS_EXYNOS=y
 CONFIG_ATA=y
 CONFIG_SATA_AHCI=y
 CONFIG_SATA_AHCI_PLATFORM=y
+CONFIG_AHCI_BRCM=m
 CONFIG_AHCI_CEVA=y
 CONFIG_AHCI_MVEBU=y
 CONFIG_AHCI_XGENE=y
@@ -309,12 +319,14 @@ CONFIG_MACVTAP=m
 CONFIG_TUN=y
 CONFIG_VETH=m
 CONFIG_VIRTIO_NET=y
+CONFIG_NET_DSA_BCM_SF2=m
 CONFIG_NET_DSA_MSCC_FELIX=m
 CONFIG_AMD_XGBE=y
 CONFIG_NET_XGENE=y
 CONFIG_ATL1C=m
 CONFIG_BCMGENET=m
 CONFIG_BNX2X=m
+CONFIG_SYSTEMPORT=m
 CONFIG_MACB=y
 CONFIG_THUNDER_NIC_PF=y
 CONFIG_FEC=y
@@ -342,6 +354,7 @@ CONFIG_MLX5_CORE=m
 CONFIG_MLX5_CORE_EN=y
 CONFIG_QCOM_EMAC=m
 CONFIG_RMNET=m
+CONFIG_R8169=m
 CONFIG_SH_ETH=y
 CONFIG_RAVB=y
 CONFIG_SMC91X=y
@@ -349,21 +362,23 @@ CONFIG_SMSC911X=y
 CONFIG_SNI_AVE=y
 CONFIG_SNI_NETSEC=y
 CONFIG_STMMAC_ETH=m
+CONFIG_DWMAC_TEGRA=m
 CONFIG_TI_K3_AM65_CPSW_NUSS=y
 CONFIG_QCOM_IPA=m
-CONFIG_MDIO_BUS_MUX_MMIOREG=y
-CONFIG_MDIO_BUS_MUX_MULTIPLEXER=y
+CONFIG_MESON_GXL_PHY=m
 CONFIG_AQUANTIA_PHY=y
 CONFIG_BCM54140_PHY=m
 CONFIG_MARVELL_PHY=m
 CONFIG_MARVELL_10G_PHY=m
-CONFIG_MESON_GXL_PHY=m
 CONFIG_MICREL_PHY=y
 CONFIG_MICROSEMI_PHY=y
 CONFIG_AT803X_PHY=y
 CONFIG_REALTEK_PHY=y
 CONFIG_ROCKCHIP_PHY=y
+CONFIG_DP83867_PHY=y
 CONFIG_VITESSE_PHY=y
+CONFIG_MDIO_BUS_MUX_MULTIPLEXER=y
+CONFIG_MDIO_BUS_MUX_MMIOREG=y
 CONFIG_USB_PEGASUS=m
 CONFIG_USB_RTL8150=m
 CONFIG_USB_RTL8152=m
@@ -379,8 +394,12 @@ CONFIG_ATH10K=m
 CONFIG_ATH10K_PCI=m
 CONFIG_ATH10K_SNOC=m
 CONFIG_WCN36XX=m
+CONFIG_ATH11K=m
+CONFIG_ATH11K_AHB=m
+CONFIG_ATH11K_PCI=m
 CONFIG_BRCMFMAC=m
 CONFIG_MWIFIEX=m
+CONFIG_MWIFIEX_SDIO=m
 CONFIG_MWIFIEX_PCIE=m
 CONFIG_WL18XX=m
 CONFIG_WLCORE_SDIO=m
@@ -397,6 +416,7 @@ CONFIG_TOUCHSCREEN_EDT_FT5X06=m
 CONFIG_INPUT_MISC=y
 CONFIG_INPUT_PM8941_PWRKEY=y
 CONFIG_INPUT_PM8XXX_VIBRATOR=m
+CONFIG_INPUT_PWM_BEEPER=m
 CONFIG_INPUT_PWM_VIBRA=m
 CONFIG_INPUT_HISI_POWERKEY=y
 # CONFIG_SERIO_SERPORT is not set
@@ -408,6 +428,7 @@ CONFIG_SERIAL_8250_EXTENDED=y
 CONFIG_SERIAL_8250_SHARE_IRQ=y
 CONFIG_SERIAL_8250_BCM2835AUX=y
 CONFIG_SERIAL_8250_DW=y
+CONFIG_SERIAL_8250_EM=y
 CONFIG_SERIAL_8250_OMAP=y
 CONFIG_SERIAL_8250_MT6577=y
 CONFIG_SERIAL_8250_UNIPHIER=y
@@ -446,6 +467,7 @@ CONFIG_I2C_CHARDEV=y
 CONFIG_I2C_MUX=y
 CONFIG_I2C_MUX_PCA954x=y
 CONFIG_I2C_BCM2835=m
+CONFIG_I2C_CADENCE=m
 CONFIG_I2C_DESIGNWARE_PLATFORM=y
 CONFIG_I2C_GPIO=m
 CONFIG_I2C_IMX=y
@@ -461,6 +483,8 @@ CONFIG_I2C_QCOM_GENI=m
 CONFIG_I2C_QUP=y
 CONFIG_I2C_RIIC=y
 CONFIG_I2C_RK3X=y
+CONFIG_I2C_RZV2M=m
+CONFIG_I2C_S3C2410=y
 CONFIG_I2C_SH_MOBILE=y
 CONFIG_I2C_TEGRA=y
 CONFIG_I2C_UNIPHIER_F=y
@@ -470,6 +494,7 @@ CONFIG_SPI=y
 CONFIG_SPI_ARMADA_3700=y
 CONFIG_SPI_BCM2835=m
 CONFIG_SPI_BCM2835AUX=m
+CONFIG_SPI_CADENCE_QUADSPI=y
 CONFIG_SPI_DESIGNWARE=m
 CONFIG_SPI_DW_DMA=y
 CONFIG_SPI_DW_MMIO=m
@@ -484,16 +509,19 @@ CONFIG_SPI_ORION=y
 CONFIG_SPI_PL022=y
 CONFIG_SPI_ROCKCHIP=y
 CONFIG_SPI_RPCIF=m
+CONFIG_SPI_RSPI=m
 CONFIG_SPI_QCOM_QSPI=m
 CONFIG_SPI_QUP=y
 CONFIG_SPI_QCOM_GENI=m
 CONFIG_SPI_S3C64XX=y
 CONFIG_SPI_SH_MSIOF=m
 CONFIG_SPI_SUN6I=y
+CONFIG_SPI_TEGRA210_QUAD=m
+CONFIG_SPI_TEGRA114=m
 CONFIG_SPI_SPIDEV=m
 CONFIG_SPMI=y
-CONFIG_PINCTRL_SINGLE=y
 CONFIG_PINCTRL_MAX77620=y
+CONFIG_PINCTRL_SINGLE=y
 CONFIG_PINCTRL_OWL=y
 CONFIG_PINCTRL_S700=y
 CONFIG_PINCTRL_S900=y
@@ -504,6 +532,8 @@ CONFIG_PINCTRL_IMX8MQ=y
 CONFIG_PINCTRL_IMX8QM=y
 CONFIG_PINCTRL_IMX8QXP=y
 CONFIG_PINCTRL_IMX8DXL=y
+CONFIG_PINCTRL_IMX8ULP=y
+CONFIG_PINCTRL_IMX93=y
 CONFIG_PINCTRL_MSM=y
 CONFIG_PINCTRL_IPQ8074=y
 CONFIG_PINCTRL_IPQ6018=y
@@ -516,10 +546,13 @@ CONFIG_PINCTRL_QDF2XXX=y
 CONFIG_PINCTRL_QCOM_SPMI_PMIC=y
 CONFIG_PINCTRL_SC7180=y
 CONFIG_PINCTRL_SC7280=y
+CONFIG_PINCTRL_SC8180X=y
+CONFIG_PINCTRL_SC8280XP=y
 CONFIG_PINCTRL_SDM845=y
 CONFIG_PINCTRL_SM8150=y
 CONFIG_PINCTRL_SM8250=y
 CONFIG_PINCTRL_SM8350=y
+CONFIG_PINCTRL_SM8450=y
 CONFIG_PINCTRL_LPASS_LPI=m
 CONFIG_GPIO_ALTERA=m
 CONFIG_GPIO_DAVINCI=y
@@ -540,9 +573,6 @@ CONFIG_GPIO_PCA953X_IRQ=y
 CONFIG_GPIO_BD9571MWV=m
 CONFIG_GPIO_MAX77620=y
 CONFIG_GPIO_SL28CPLD=m
-CONFIG_POWER_AVS=y
-CONFIG_QCOM_CPR=y
-CONFIG_ROCKCHIP_IODOMAIN=y
 CONFIG_POWER_RESET_MSM=y
 CONFIG_POWER_RESET_QCOM_PON=m
 CONFIG_POWER_RESET_XGENE=y
@@ -550,11 +580,15 @@ CONFIG_POWER_RESET_SYSCON=y
 CONFIG_SYSCON_REBOOT_MODE=y
 CONFIG_BATTERY_SBS=m
 CONFIG_BATTERY_BQ27XXX=y
-CONFIG_SENSORS_ARM_SCMI=y
 CONFIG_BATTERY_MAX17042=m
+CONFIG_CHARGER_MT6360=m
 CONFIG_CHARGER_BQ25890=m
 CONFIG_CHARGER_BQ25980=m
+CONFIG_SENSORS_ARM_SCMI=y
 CONFIG_SENSORS_ARM_SCPI=y
+CONFIG_SENSORS_GPIO_FAN=m
+CONFIG_SENSORS_JC42=m
+CONFIG_SENSORS_LM75=m
 CONFIG_SENSORS_LM90=m
 CONFIG_SENSORS_PWM_FAN=m
 CONFIG_SENSORS_RASPBERRYPI_HWMON=m
@@ -563,22 +597,25 @@ CONFIG_SENSORS_INA2XX=m
 CONFIG_SENSORS_INA3221=m
 CONFIG_THERMAL_GOV_POWER_ALLOCATOR=y
 CONFIG_CPU_THERMAL=y
+CONFIG_DEVFREQ_THERMAL=y
 CONFIG_THERMAL_EMULATION=y
-CONFIG_QORIQ_THERMAL=m
-CONFIG_SUN8I_THERMAL=y
 CONFIG_IMX_SC_THERMAL=m
 CONFIG_IMX8MM_THERMAL=m
+CONFIG_QORIQ_THERMAL=m
+CONFIG_SUN8I_THERMAL=y
 CONFIG_ROCKCHIP_THERMAL=m
 CONFIG_RCAR_THERMAL=y
 CONFIG_RCAR_GEN3_THERMAL=y
+CONFIG_RZG2L_THERMAL=y
 CONFIG_ARMADA_THERMAL=y
 CONFIG_BCM2711_THERMAL=m
 CONFIG_BCM2835_THERMAL=m
 CONFIG_BRCMSTB_THERMAL=m
 CONFIG_EXYNOS_THERMAL=y
-CONFIG_TEGRA_BPMP_THERMAL=m
 CONFIG_TEGRA_SOCTHERM=m
+CONFIG_TEGRA_BPMP_THERMAL=m
 CONFIG_QCOM_TSENS=y
+CONFIG_QCOM_SPMI_ADC_TM5=m
 CONFIG_QCOM_SPMI_TEMP_ALARM=m
 CONFIG_QCOM_LMH=m
 CONFIG_UNIPHIER_THERMAL=y
@@ -586,7 +623,6 @@ CONFIG_WATCHDOG=y
 CONFIG_SL28CPLD_WATCHDOG=m
 CONFIG_ARM_SP805_WATCHDOG=y
 CONFIG_ARM_SBSA_WATCHDOG=y
-CONFIG_ARM_SMC_WATCHDOG=y
 CONFIG_S3C2410_WATCHDOG=y
 CONFIG_DW_WATCHDOG=y
 CONFIG_SUNXI_WATCHDOG=m
@@ -595,9 +631,14 @@ CONFIG_IMX_SC_WDT=m
 CONFIG_QCOM_WDT=m
 CONFIG_MESON_GXBB_WATCHDOG=m
 CONFIG_MESON_WATCHDOG=m
+CONFIG_ARM_SMC_WATCHDOG=y
 CONFIG_RENESAS_WDT=y
+CONFIG_RENESAS_RZG2LWDT=y
 CONFIG_UNIPHIER_WATCHDOG=y
+CONFIG_PM8916_WATCHDOG=m
 CONFIG_BCM2835_WDT=y
+CONFIG_BCM7038_WDT=m
+CONFIG_NPCM7XX_WATCHDOG=y
 CONFIG_MFD_ALTERA_SYSMGR=y
 CONFIG_MFD_BD9571MWV=y
 CONFIG_MFD_AXP20X_I2C=y
@@ -606,6 +647,7 @@ CONFIG_MFD_EXYNOS_LPASS=m
 CONFIG_MFD_HI6421_PMIC=y
 CONFIG_MFD_HI655X_PMIC=y
 CONFIG_MFD_MAX77620=y
+CONFIG_MFD_MT6360=y
 CONFIG_MFD_MT6397=y
 CONFIG_MFD_SPMI_PMIC=y
 CONFIG_MFD_RK808=y
@@ -625,6 +667,8 @@ CONFIG_REGULATOR_MAX77620=y
 CONFIG_REGULATOR_MAX8973=y
 CONFIG_REGULATOR_MP8859=y
 CONFIG_REGULATOR_MT6358=y
+CONFIG_REGULATOR_MT6359=y
+CONFIG_REGULATOR_MT6360=y
 CONFIG_REGULATOR_MT6397=y
 CONFIG_REGULATOR_PCA9450=y
 CONFIG_REGULATOR_PF8X00=y
@@ -647,32 +691,34 @@ CONFIG_MEDIA_CAMERA_SUPPORT=y
 CONFIG_MEDIA_ANALOG_TV_SUPPORT=y
 CONFIG_MEDIA_DIGITAL_TV_SUPPORT=y
 CONFIG_MEDIA_SDR_SUPPORT=y
-CONFIG_MEDIA_CONTROLLER=y
-CONFIG_VIDEO_V4L2_SUBDEV_API=y
 CONFIG_MEDIA_PLATFORM_SUPPORT=y
 # CONFIG_DVB_NET is not set
 CONFIG_MEDIA_USB_SUPPORT=y
 CONFIG_USB_VIDEO_CLASS=m
 CONFIG_V4L_PLATFORM_DRIVERS=y
+CONFIG_SDR_PLATFORM_DRIVERS=y
+CONFIG_V4L_MEM2MEM_DRIVERS=y
+CONFIG_VIDEO_QCOM_CAMSS=m
+CONFIG_VIDEO_QCOM_VENUS=m
+CONFIG_VIDEO_RCAR_ISP=m
 CONFIG_VIDEO_RCAR_CSI2=m
 CONFIG_VIDEO_RCAR_VIN=m
-CONFIG_VIDEO_SUN6I_CSI=m
-CONFIG_V4L_MEM2MEM_DRIVERS=y
-CONFIG_VIDEO_SAMSUNG_S5P_JPEG=m
-CONFIG_VIDEO_SAMSUNG_S5P_MFC=m
-CONFIG_VIDEO_SAMSUNG_EXYNOS_GSC=m
-CONFIG_VIDEO_RENESAS_FDP1=m
 CONFIG_VIDEO_RENESAS_FCP=m
+CONFIG_VIDEO_RENESAS_FDP1=m
 CONFIG_VIDEO_RENESAS_VSP1=m
-CONFIG_VIDEO_QCOM_VENUS=m
-CONFIG_SDR_PLATFORM_DRIVERS=y
 CONFIG_VIDEO_RCAR_DRIF=m
+CONFIG_VIDEO_SAMSUNG_EXYNOS_GSC=m
+CONFIG_VIDEO_SAMSUNG_S5P_JPEG=m
+CONFIG_VIDEO_SAMSUNG_S5P_MFC=m
+CONFIG_VIDEO_SUN6I_CSI=m
 CONFIG_VIDEO_IMX219=m
+CONFIG_VIDEO_OV5640=m
 CONFIG_VIDEO_OV5645=m
-CONFIG_VIDEO_QCOM_CAMSS=m
 CONFIG_DRM=m
 CONFIG_DRM_I2C_NXP_TDA998X=m
+CONFIG_DRM_HDLCD=m
 CONFIG_DRM_MALI_DISPLAY=m
+CONFIG_DRM_KOMEDA=m
 CONFIG_DRM_NOUVEAU=m
 CONFIG_DRM_EXYNOS=m
 CONFIG_DRM_EXYNOS5433_DECON=y
@@ -690,35 +736,37 @@ CONFIG_ROCKCHIP_INNO_HDMI=y
 CONFIG_ROCKCHIP_LVDS=y
 CONFIG_DRM_RCAR_DU=m
 CONFIG_DRM_RCAR_DW_HDMI=m
+CONFIG_DRM_RCAR_MIPI_DSI=m
 CONFIG_DRM_SUN4I=m
 CONFIG_DRM_SUN6I_DSI=m
 CONFIG_DRM_SUN8I_DW_HDMI=m
 CONFIG_DRM_SUN8I_MIXER=m
 CONFIG_DRM_MSM=m
 CONFIG_DRM_TEGRA=m
+CONFIG_DRM_PANEL_BOE_TV101WUM_NL6=m
 CONFIG_DRM_PANEL_LVDS=m
 CONFIG_DRM_PANEL_SIMPLE=m
 CONFIG_DRM_PANEL_EDP=m
-CONFIG_DRM_PANEL_BOE_TV101WUM_NL6=m
 CONFIG_DRM_PANEL_MANTIX_MLAF057WE51=m
 CONFIG_DRM_PANEL_RAYDIUM_RM67191=m
 CONFIG_DRM_PANEL_SITRONIX_ST7703=m
 CONFIG_DRM_PANEL_TRULY_NT35597_WQXGA=m
-CONFIG_DRM_DISPLAY_CONNECTOR=m
 CONFIG_DRM_LONTIUM_LT8912B=m
-CONFIG_DRM_NWL_MIPI_DSI=m
 CONFIG_DRM_LONTIUM_LT9611=m
+CONFIG_DRM_LONTIUM_LT9611UXC=m
+CONFIG_DRM_NWL_MIPI_DSI=m
 CONFIG_DRM_PARADE_PS8640=m
 CONFIG_DRM_SII902X=m
 CONFIG_DRM_SIMPLE_BRIDGE=m
 CONFIG_DRM_THINE_THC63LVD1024=m
 CONFIG_DRM_TI_SN65DSI86=m
-CONFIG_DRM_LONTIUM_LT9611UXC=m
 CONFIG_DRM_I2C_ADV7511=m
 CONFIG_DRM_I2C_ADV7511_AUDIO=y
+CONFIG_DRM_CDNS_MHDP8546=m
 CONFIG_DRM_DW_HDMI_AHB_AUDIO=m
 CONFIG_DRM_DW_HDMI_CEC=m
 CONFIG_DRM_IMX_DCSS=m
+CONFIG_DRM_V3D=m
 CONFIG_DRM_VC4=m
 CONFIG_DRM_ETNAVIV=m
 CONFIG_DRM_HISI_HIBMC=m
@@ -730,6 +778,7 @@ CONFIG_DRM_MESON=m
 CONFIG_DRM_PL111=m
 CONFIG_DRM_LIMA=m
 CONFIG_DRM_PANFROST=m
+CONFIG_DRM_TIDSS=m
 CONFIG_FB=y
 CONFIG_FB_MODE_HELPERS=y
 CONFIG_FB_EFI=y
@@ -744,15 +793,14 @@ CONFIG_SND_HDA_TEGRA=m
 CONFIG_SND_HDA_CODEC_HDMI=m
 CONFIG_SND_SOC=y
 CONFIG_SND_BCM2835_SOC_I2S=m
-CONFIG_SND_SOC_FSL_SAI=m
 CONFIG_SND_SOC_FSL_ASRC=m
 CONFIG_SND_SOC_FSL_MICFIL=m
 CONFIG_SND_SOC_FSL_EASRC=m
 CONFIG_SND_IMX_SOC=m
 CONFIG_SND_SOC_IMX_SGTL5000=m
 CONFIG_SND_SOC_IMX_SPDIF=m
-CONFIG_SND_SOC_IMX_AUDMIX=m
 CONFIG_SND_SOC_FSL_ASOC_CARD=m
+CONFIG_SND_SOC_IMX_AUDMIX=m
 CONFIG_SND_MESON_AXG_SOUND_CARD=m
 CONFIG_SND_MESON_GX_SOUND_CARD=m
 CONFIG_SND_SOC_QCOM=m
@@ -760,6 +808,8 @@ CONFIG_SND_SOC_APQ8016_SBC=m
 CONFIG_SND_SOC_MSM8996=m
 CONFIG_SND_SOC_SDM845=m
 CONFIG_SND_SOC_SM8250=m
+CONFIG_SND_SOC_SC7180=m
+CONFIG_SND_SOC_SC7280=m
 CONFIG_SND_SOC_ROCKCHIP=m
 CONFIG_SND_SOC_ROCKCHIP_SPDIF=m
 CONFIG_SND_SOC_ROCKCHIP_RT5645=m
@@ -767,12 +817,17 @@ CONFIG_SND_SOC_RK3399_GRU_SOUND=m
 CONFIG_SND_SOC_SAMSUNG=y
 CONFIG_SND_SOC_RCAR=m
 CONFIG_SND_SOC_RZ=m
+CONFIG_SND_SUN8I_CODEC=m
+CONFIG_SND_SUN8I_CODEC_ANALOG=m
+CONFIG_SND_SUN50I_CODEC_ANALOG=m
 CONFIG_SND_SUN4I_I2S=m
 CONFIG_SND_SUN4I_SPDIF=m
 CONFIG_SND_SOC_TEGRA=m
 CONFIG_SND_SOC_TEGRA210_AHUB=m
 CONFIG_SND_SOC_TEGRA210_DMIC=m
 CONFIG_SND_SOC_TEGRA210_I2S=m
+CONFIG_SND_SOC_TEGRA210_OPE=m
+CONFIG_SND_SOC_TEGRA186_ASRC=m
 CONFIG_SND_SOC_TEGRA186_DSPK=m
 CONFIG_SND_SOC_TEGRA210_ADMAIF=m
 CONFIG_SND_SOC_TEGRA210_MVC=m
@@ -792,26 +847,32 @@ CONFIG_SND_SOC_RT5659=m
 CONFIG_SND_SOC_SIMPLE_AMPLIFIER=m
 CONFIG_SND_SOC_SIMPLE_MUX=m
 CONFIG_SND_SOC_TAS571X=m
+CONFIG_SND_SOC_TLV320AIC32X4_I2C=m
+CONFIG_SND_SOC_WCD9335=m
 CONFIG_SND_SOC_WCD934X=m
+CONFIG_SND_SOC_WM8524=m
 CONFIG_SND_SOC_WM8904=m
 CONFIG_SND_SOC_WM8960=m
 CONFIG_SND_SOC_WM8962=m
 CONFIG_SND_SOC_WM8978=m
 CONFIG_SND_SOC_WSA881X=m
+CONFIG_SND_SOC_NAU8822=m
 CONFIG_SND_SOC_LPASS_WSA_MACRO=m
 CONFIG_SND_SOC_LPASS_VA_MACRO=m
+CONFIG_SND_SOC_LPASS_RX_MACRO=m
+CONFIG_SND_SOC_LPASS_TX_MACRO=m
 CONFIG_SND_SIMPLE_CARD=m
 CONFIG_SND_AUDIO_GRAPH_CARD=m
+CONFIG_SND_AUDIO_GRAPH_CARD2=m
 CONFIG_HID_MULTITOUCH=m
 CONFIG_I2C_HID_ACPI=m
 CONFIG_I2C_HID_OF=m
-CONFIG_USB_CONN_GPIO=m
 CONFIG_USB=y
 CONFIG_USB_OTG=y
 CONFIG_USB_XHCI_HCD=y
-CONFIG_USB_XHCI_PCI=m
 CONFIG_USB_XHCI_PCI_RENESAS=m
 CONFIG_USB_XHCI_TEGRA=y
+CONFIG_USB_BRCMSTB=m
 CONFIG_USB_EHCI_HCD=y
 CONFIG_USB_EHCI_EXYNOS=y
 CONFIG_USB_EHCI_HCD_PLATFORM=y
@@ -822,6 +883,10 @@ CONFIG_USB_RENESAS_USBHS_HCD=m
 CONFIG_USB_RENESAS_USBHS=m
 CONFIG_USB_ACM=m
 CONFIG_USB_STORAGE=y
+CONFIG_USB_CDNS_SUPPORT=m
+CONFIG_USB_CDNS3=m
+CONFIG_USB_CDNS3_GADGET=y
+CONFIG_USB_CDNS3_HOST=y
 CONFIG_USB_MTU3=y
 CONFIG_USB_MUSB_HDRC=y
 CONFIG_USB_MUSB_SUNXI=y
@@ -856,8 +921,8 @@ CONFIG_TYPEC=m
 CONFIG_TYPEC_TCPM=m
 CONFIG_TYPEC_TCPCI=m
 CONFIG_TYPEC_FUSB302=m
-CONFIG_TYPEC_HD3SS3220=m
 CONFIG_TYPEC_TPS6598X=m
+CONFIG_TYPEC_HD3SS3220=m
 CONFIG_MMC=y
 CONFIG_MMC_BLOCK_MINORS=32
 CONFIG_MMC_ARMMMCI=y
@@ -865,6 +930,7 @@ CONFIG_MMC_SDHCI=y
 CONFIG_MMC_SDHCI_ACPI=y
 CONFIG_MMC_SDHCI_PLTFM=y
 CONFIG_MMC_SDHCI_OF_ARASAN=y
+CONFIG_MMC_SDHCI_OF_DWCMSHC=y
 CONFIG_MMC_SDHCI_OF_ESDHC=y
 CONFIG_MMC_SDHCI_CADENCE=y
 CONFIG_MMC_SDHCI_ESDHC_IMX=y
@@ -886,13 +952,21 @@ CONFIG_MMC_MTK=y
 CONFIG_MMC_SDHCI_XENON=y
 CONFIG_MMC_SDHCI_AM654=y
 CONFIG_MMC_OWL=y
+CONFIG_SCSI_UFSHCD=y
+CONFIG_SCSI_UFSHCD_PLATFORM=y
+CONFIG_SCSI_UFS_QCOM=m
+CONFIG_SCSI_UFS_HISI=y
+CONFIG_SCSI_UFS_RENESAS=m
+CONFIG_SCSI_UFS_EXYNOS=y
 CONFIG_NEW_LEDS=y
 CONFIG_LEDS_CLASS=y
+CONFIG_LEDS_CLASS_MULTICOLOR=m
 CONFIG_LEDS_LM3692X=m
 CONFIG_LEDS_PCA9532=m
 CONFIG_LEDS_GPIO=y
 CONFIG_LEDS_PWM=y
 CONFIG_LEDS_SYSCON=y
+CONFIG_LEDS_QCOM_LPG=m
 CONFIG_LEDS_TRIGGER_TIMER=y
 CONFIG_LEDS_TRIGGER_DISK=y
 CONFIG_LEDS_TRIGGER_HEARTBEAT=y
@@ -907,6 +981,7 @@ CONFIG_RTC_DRV_DS1307=m
 CONFIG_RTC_DRV_HYM8563=m
 CONFIG_RTC_DRV_MAX77686=y
 CONFIG_RTC_DRV_RK808=m
+CONFIG_RTC_DRV_PCF85063=m
 CONFIG_RTC_DRV_PCF85363=m
 CONFIG_RTC_DRV_M41T80=m
 CONFIG_RTC_DRV_RX8581=m
@@ -926,20 +1001,23 @@ CONFIG_RTC_DRV_PM8XXX=m
 CONFIG_RTC_DRV_TEGRA=y
 CONFIG_RTC_DRV_SNVS=m
 CONFIG_RTC_DRV_IMX_SC=m
+CONFIG_RTC_DRV_MT6397=m
 CONFIG_RTC_DRV_XGENE=y
 CONFIG_DMADEVICES=y
 CONFIG_DMA_BCM2835=y
 CONFIG_DMA_SUN6I=m
 CONFIG_FSL_EDMA=y
-CONFIG_IMX_SDMA=y
+CONFIG_IMX_SDMA=m
 CONFIG_K3_DMA=y
 CONFIG_MV_XOR=y
 CONFIG_MV_XOR_V2=y
 CONFIG_OWL_DMA=y
 CONFIG_PL330_DMA=y
+CONFIG_TEGRA186_GPC_DMA=y
 CONFIG_TEGRA20_APB_DMA=y
 CONFIG_TEGRA210_ADMA=m
 CONFIG_QCOM_BAM_DMA=y
+CONFIG_QCOM_GPI_DMA=m
 CONFIG_QCOM_HIDMA_MGMT=y
 CONFIG_QCOM_HIDMA=y
 CONFIG_RCAR_DMAC=y
@@ -954,24 +1032,25 @@ CONFIG_VIRTIO_BALLOON=y
 CONFIG_VIRTIO_MMIO=y
 CONFIG_XEN_GNTDEV=y
 CONFIG_XEN_GRANT_DEV_ALLOC=y
-CONFIG_MFD_CROS_EC_DEV=y
 CONFIG_STAGING=y
 CONFIG_STAGING_MEDIA=y
 CONFIG_VIDEO_HANTRO=m
+CONFIG_VIDEO_IMX_MEDIA=m
+CONFIG_VIDEO_MAX96712=m
 CONFIG_CHROME_PLATFORMS=y
 CONFIG_CROS_EC=y
 CONFIG_CROS_EC_I2C=y
 CONFIG_CROS_EC_SPI=y
 CONFIG_CROS_EC_CHARDEV=m
-CONFIG_COMMON_CLK_SCMI=y
 CONFIG_COMMON_CLK_RK808=y
+CONFIG_COMMON_CLK_SCMI=y
 CONFIG_COMMON_CLK_SCPI=y
 CONFIG_COMMON_CLK_CS2000_CP=y
 CONFIG_COMMON_CLK_FSL_SAI=y
 CONFIG_COMMON_CLK_S2MPS11=y
 CONFIG_COMMON_CLK_PWM=y
 CONFIG_COMMON_CLK_VC5=y
-CONFIG_COMMON_CLK_ZYNQMP=y
+CONFIG_COMMON_CLK_NPCM8XX=y
 CONFIG_COMMON_CLK_BD718XX=m
 CONFIG_CLK_RASPBERRYPI=m
 CONFIG_CLK_IMX8MM=y
@@ -979,6 +1058,8 @@ CONFIG_CLK_IMX8MN=y
 CONFIG_CLK_IMX8MP=y
 CONFIG_CLK_IMX8MQ=y
 CONFIG_CLK_IMX8QXP=y
+CONFIG_CLK_IMX8ULP=y
+CONFIG_CLK_IMX93=y
 CONFIG_TI_SCI_CLK=y
 CONFIG_COMMON_CLK_QCOM=y
 CONFIG_QCOM_A53PLL=y
@@ -986,8 +1067,8 @@ CONFIG_QCOM_CLK_APCS_MSM8916=y
 CONFIG_QCOM_CLK_APCC_MSM8996=y
 CONFIG_QCOM_CLK_SMD_RPM=y
 CONFIG_QCOM_CLK_RPMH=y
-CONFIG_IPQ_GCC_8074=y
 CONFIG_IPQ_GCC_6018=y
+CONFIG_IPQ_GCC_8074=y
 CONFIG_MSM_GCC_8916=y
 CONFIG_MSM_GCC_8994=y
 CONFIG_MSM_MMCC_8996=y
@@ -995,22 +1076,24 @@ CONFIG_MSM_GCC_8998=y
 CONFIG_QCS_GCC_404=y
 CONFIG_SC_GCC_7180=y
 CONFIG_SC_GCC_7280=y
+CONFIG_SC_GCC_8180X=y
+CONFIG_SC_GCC_8280XP=y
 CONFIG_SDM_CAMCC_845=m
-CONFIG_SDM_GCC_845=y
 CONFIG_SDM_GPUCC_845=y
 CONFIG_SDM_VIDEOCC_845=y
 CONFIG_SDM_DISPCC_845=y
-CONFIG_SM_GCC_8150=y
-CONFIG_SM_GCC_8250=y
+CONFIG_SM_DISPCC_8250=y
 CONFIG_SM_GCC_8350=y
+CONFIG_SM_GCC_8450=y
 CONFIG_SM_GPUCC_8150=y
 CONFIG_SM_GPUCC_8250=y
-CONFIG_SM_DISPCC_8250=y
+CONFIG_SM_VIDEOCC_8250=y
 CONFIG_QCOM_HFPLL=y
 CONFIG_CLK_GFM_LPASS_SM8250=m
 CONFIG_CLK_RCAR_USB2_CLOCK_SEL=y
 CONFIG_HWSPINLOCK=y
 CONFIG_HWSPINLOCK_QCOM=y
+CONFIG_RENESAS_OSTM=y
 CONFIG_ARM_MHU=y
 CONFIG_IMX_MBOX=y
 CONFIG_PLATFORM_MHU=y
@@ -1024,11 +1107,13 @@ CONFIG_ARM_SMMU_V3=y
 CONFIG_MTK_IOMMU=y
 CONFIG_QCOM_IOMMU=y
 CONFIG_REMOTEPROC=y
+CONFIG_QCOM_Q6V5_ADSP=m
 CONFIG_QCOM_Q6V5_MSS=m
 CONFIG_QCOM_Q6V5_PAS=m
 CONFIG_QCOM_SYSMON=m
 CONFIG_QCOM_WCNSS_PIL=m
 CONFIG_RPMSG_CHAR=m
+CONFIG_RPMSG_CTRL=m
 CONFIG_RPMSG_QCOM_GLINK_RPM=y
 CONFIG_RPMSG_QCOM_GLINK_SMEM=m
 CONFIG_RPMSG_QCOM_SMD=y
@@ -1039,10 +1124,14 @@ CONFIG_RASPBERRYPI_POWER=y
 CONFIG_FSL_DPAA=y
 CONFIG_FSL_MC_DPIO=y
 CONFIG_FSL_RCPM=y
+CONFIG_MTK_DEVAPC=m
 CONFIG_MTK_PMIC_WRAP=y
 CONFIG_QCOM_AOSS_QMP=y
 CONFIG_QCOM_COMMAND_DB=y
+CONFIG_QCOM_CPR=y
 CONFIG_QCOM_GENI_SE=y
+CONFIG_QCOM_LLCC=m
+CONFIG_QCOM_OCMEM=m
 CONFIG_QCOM_RMTFS_MEM=m
 CONFIG_QCOM_RPMH=y
 CONFIG_QCOM_RPMHPD=y
@@ -1052,24 +1141,32 @@ CONFIG_QCOM_SMD_RPM=y
 CONFIG_QCOM_SMP2P=y
 CONFIG_QCOM_SMSM=y
 CONFIG_QCOM_SOCINFO=m
-CONFIG_QCOM_WCNSS_CTRL=m
+CONFIG_QCOM_SPM=m
 CONFIG_QCOM_STATS=m
+CONFIG_QCOM_WCNSS_CTRL=m
 CONFIG_QCOM_APR=m
-CONFIG_ARCH_R8A774A1=y
-CONFIG_ARCH_R8A774B1=y
-CONFIG_ARCH_R8A774C0=y
-CONFIG_ARCH_R8A774E1=y
+CONFIG_QCOM_ICC_BWMON=m
+CONFIG_ARCH_R8A77995=y
+CONFIG_ARCH_R8A77990=y
 CONFIG_ARCH_R8A77950=y
 CONFIG_ARCH_R8A77951=y
+CONFIG_ARCH_R8A77965=y
 CONFIG_ARCH_R8A77960=y
 CONFIG_ARCH_R8A77961=y
-CONFIG_ARCH_R8A77965=y
-CONFIG_ARCH_R8A77970=y
+CONFIG_ARCH_R8A779F0=y
 CONFIG_ARCH_R8A77980=y
-CONFIG_ARCH_R8A77990=y
-CONFIG_ARCH_R8A77995=y
+CONFIG_ARCH_R8A77970=y
 CONFIG_ARCH_R8A779A0=y
+CONFIG_ARCH_R8A779G0=y
+CONFIG_ARCH_R8A774C0=y
+CONFIG_ARCH_R8A774E1=y
+CONFIG_ARCH_R8A774A1=y
+CONFIG_ARCH_R8A774B1=y
+CONFIG_ARCH_R9A07G043=y
 CONFIG_ARCH_R9A07G044=y
+CONFIG_ARCH_R9A07G054=y
+CONFIG_ARCH_R9A09G011=y
+CONFIG_ROCKCHIP_IODOMAIN=y
 CONFIG_ROCKCHIP_PM_DOMAINS=y
 CONFIG_ARCH_TEGRA_132_SOC=y
 CONFIG_ARCH_TEGRA_210_SOC=y
@@ -1090,6 +1187,7 @@ CONFIG_QCOM_SPMI_VADC=m
 CONFIG_QCOM_SPMI_ADC5=m
 CONFIG_ROCKCHIP_SARADC=m
 CONFIG_RZG2L_ADC=m
+CONFIG_TI_ADS1015=m
 CONFIG_IIO_CROS_EC_SENSORS_CORE=m
 CONFIG_IIO_CROS_EC_SENSORS=m
 CONFIG_IIO_ST_LSM6DSX=m
@@ -1101,6 +1199,7 @@ CONFIG_IIO_CROS_EC_BARO=m
 CONFIG_MPL3115=m
 CONFIG_PWM=y
 CONFIG_PWM_BCM2835=m
+CONFIG_PWM_BRCMSTB=m
 CONFIG_PWM_CROS_EC=m
 CONFIG_PWM_IMX27=m
 CONFIG_PWM_MESON=m
@@ -1123,16 +1222,23 @@ CONFIG_RESET_RZG2L_USBPHY_CTRL=y
 CONFIG_RESET_TI_SCI=y
 CONFIG_PHY_XGENE=y
 CONFIG_PHY_SUN4I_USB=y
+CONFIG_PHY_CADENCE_TORRENT=m
+CONFIG_PHY_CADENCE_SIERRA=m
 CONFIG_PHY_MIXEL_MIPI_DPHY=m
+CONFIG_PHY_FSL_IMX8M_PCIE=y
 CONFIG_PHY_HI6220_USB=y
 CONFIG_PHY_HISTB_COMBPHY=y
 CONFIG_PHY_HISI_INNO_USB2=y
 CONFIG_PHY_MVEBU_CP110_COMPHY=y
 CONFIG_PHY_MTK_TPHY=y
+CONFIG_PHY_QCOM_EDP=m
+CONFIG_PHY_QCOM_PCIE2=m
 CONFIG_PHY_QCOM_QMP=m
 CONFIG_PHY_QCOM_QUSB2=m
-CONFIG_PHY_QCOM_USB_HS=y
-CONFIG_PHY_QCOM_USB_SNPS_FEMTO_V2=y
+CONFIG_PHY_QCOM_USB_HS=m
+CONFIG_PHY_QCOM_USB_SNPS_FEMTO_V2=m
+CONFIG_PHY_QCOM_USB_HS_28NM=m
+CONFIG_PHY_QCOM_USB_SS=m
 CONFIG_PHY_RCAR_GEN3_PCIE=y
 CONFIG_PHY_RCAR_GEN3_USB2=y
 CONFIG_PHY_RCAR_GEN3_USB3=m
@@ -1146,21 +1252,31 @@ CONFIG_PHY_SAMSUNG_UFS=y
 CONFIG_PHY_UNIPHIER_USB2=y
 CONFIG_PHY_UNIPHIER_USB3=y
 CONFIG_PHY_TEGRA_XUSB=y
+CONFIG_PHY_AM654_SERDES=m
+CONFIG_PHY_J721E_WIZ=m
+CONFIG_ARM_CCI_PMU=m
+CONFIG_ARM_CCN=m
+CONFIG_ARM_CMN=m
 CONFIG_ARM_SMMU_V3_PMU=m
+CONFIG_ARM_DSU_PMU=m
 CONFIG_FSL_IMX8_DDR_PMU=m
-CONFIG_HISI_PMU=y
+CONFIG_ARM_SPE_PMU=m
+CONFIG_ARM_DMC620_PMU=m
 CONFIG_QCOM_L2_PMU=y
 CONFIG_QCOM_L3_PMU=y
+CONFIG_HISI_PMU=y
 CONFIG_NVMEM_IMX_OCOTP=y
 CONFIG_NVMEM_IMX_OCOTP_SCU=y
-CONFIG_QCOM_QFPROM=y
-CONFIG_MTK_EFUSE=y
-CONFIG_ROCKCHIP_EFUSE=y
+CONFIG_NVMEM_MTK_EFUSE=y
+CONFIG_NVMEM_QCOM_QFPROM=y
+CONFIG_NVMEM_ROCKCHIP_EFUSE=y
 CONFIG_NVMEM_SUNXI_SID=y
-CONFIG_UNIPHIER_EFUSE=y
-CONFIG_MESON_EFUSE=m
+CONFIG_NVMEM_UNIPHIER_EFUSE=y
+CONFIG_NVMEM_MESON_EFUSE=m
 CONFIG_NVMEM_RMEM=m
+CONFIG_NVMEM_LAYERSCAPE_SFP=m
 CONFIG_FPGA=y
+CONFIG_FPGA_MGR_ALTERA_CVP=m
 CONFIG_FPGA_MGR_STRATIX10_SOC=m
 CONFIG_FPGA_BRIDGE=m
 CONFIG_ALTERA_FREEZE_BRIDGE=m
@@ -1168,21 +1284,29 @@ CONFIG_FPGA_REGION=m
 CONFIG_OF_FPGA_REGION=m
 CONFIG_TEE=y
 CONFIG_OPTEE=y
+CONFIG_MUX_MMIO=y
 CONFIG_SLIMBUS=m
 CONFIG_SLIM_QCOM_CTRL=m
 CONFIG_SLIM_QCOM_NGD_CTRL=m
-CONFIG_MUX_MMIO=y
 CONFIG_INTERCONNECT=y
 CONFIG_INTERCONNECT_IMX=m
+CONFIG_INTERCONNECT_IMX8MM=m
+CONFIG_INTERCONNECT_IMX8MN=m
 CONFIG_INTERCONNECT_IMX8MQ=m
 CONFIG_INTERCONNECT_QCOM=y
 CONFIG_INTERCONNECT_QCOM_MSM8916=m
+CONFIG_INTERCONNECT_QCOM_MSM8996=m
 CONFIG_INTERCONNECT_QCOM_OSM_L3=m
+CONFIG_INTERCONNECT_QCOM_QCS404=m
+CONFIG_INTERCONNECT_QCOM_SC7180=m
 CONFIG_INTERCONNECT_QCOM_SC7280=y
+CONFIG_INTERCONNECT_QCOM_SC8180X=y
+CONFIG_INTERCONNECT_QCOM_SC8280XP=y
 CONFIG_INTERCONNECT_QCOM_SDM845=y
 CONFIG_INTERCONNECT_QCOM_SM8150=m
 CONFIG_INTERCONNECT_QCOM_SM8250=m
 CONFIG_INTERCONNECT_QCOM_SM8350=m
+CONFIG_INTERCONNECT_QCOM_SM8450=m
 CONFIG_EXT2_FS=y
 CONFIG_EXT3_FS=y
 CONFIG_EXT4_FS_POSIX_ACL=y
@@ -1211,6 +1335,7 @@ CONFIG_NLS_CODEPAGE_437=y
 CONFIG_NLS_ISO8859_1=y
 CONFIG_SECURITY=y
 CONFIG_CRYPTO_ECHAINIV=y
+CONFIG_CRYPTO_MICHAEL_MIC=m
 CONFIG_CRYPTO_ANSI_CPRNG=y
 CONFIG_CRYPTO_USER_API_RNG=m
 CONFIG_CRYPTO_DEV_SUN8I_CE=m
@@ -1224,12 +1349,20 @@ CONFIG_CRYPTO_DEV_HISI_HPRE=m
 CONFIG_CRYPTO_DEV_HISI_TRNG=m
 CONFIG_CMA_SIZE_MBYTES=32
 CONFIG_PRINTK_TIME=y
-CONFIG_DEBUG_INFO=y
+CONFIG_DEBUG_KERNEL=y
+CONFIG_DEBUG_INFO_DWARF_TOOLCHAIN_DEFAULT=y
 CONFIG_DEBUG_INFO_REDUCED=y
 CONFIG_MAGIC_SYSRQ=y
 CONFIG_DEBUG_FS=y
-CONFIG_DEBUG_KERNEL=y
 # CONFIG_SCHED_DEBUG is not set
 # CONFIG_DEBUG_PREEMPT is not set
 # CONFIG_FTRACE is not set
+CONFIG_CORESIGHT=m
+CONFIG_CORESIGHT_LINK_AND_SINK_TMC=m
+CONFIG_CORESIGHT_CATU=m
+CONFIG_CORESIGHT_SINK_TPIU=m
+CONFIG_CORESIGHT_SINK_ETBV10=m
+CONFIG_CORESIGHT_STM=m
+CONFIG_CORESIGHT_CPU_DEBUG=m
+CONFIG_CORESIGHT_CTI=m
 CONFIG_MEMTEST=y
diff --git a/arch/arm64/crypto/Kconfig b/arch/arm64/crypto/Kconfig
index addfa413650b..8bd80508a710 100644
--- a/arch/arm64/crypto/Kconfig
+++ b/arch/arm64/crypto/Kconfig
@@ -1,123 +1,282 @@
 # SPDX-License-Identifier: GPL-2.0
 
-menuconfig ARM64_CRYPTO
-	bool "ARM64 Accelerated Cryptographic Algorithms"
-	depends on ARM64
+menu "Accelerated Cryptographic Algorithms for CPU (arm64)"
+
+config CRYPTO_GHASH_ARM64_CE
+	tristate "Hash functions: GHASH (ARMv8 Crypto Extensions)"
+	depends on KERNEL_MODE_NEON
+	select CRYPTO_HASH
+	select CRYPTO_GF128MUL
+	select CRYPTO_LIB_AES
+	select CRYPTO_AEAD
 	help
-	  Say Y here to choose from a selection of cryptographic algorithms
-	  implemented using ARM64 specific CPU features or instructions.
+	  GCM GHASH function (NIST SP800-38D)
 
-if ARM64_CRYPTO
+	  Architecture: arm64 using:
+	  - ARMv8 Crypto Extensions
 
-config CRYPTO_SHA256_ARM64
-	tristate "SHA-224/SHA-256 digest algorithm for arm64"
-	select CRYPTO_HASH
+config CRYPTO_NHPOLY1305_NEON
+	tristate "Hash functions: NHPoly1305 (NEON)"
+	depends on KERNEL_MODE_NEON
+	select CRYPTO_NHPOLY1305
+	help
+	  NHPoly1305 hash function (Adiantum)
 
-config CRYPTO_SHA512_ARM64
-	tristate "SHA-384/SHA-512 digest algorithm for arm64"
+	  Architecture: arm64 using:
+	  - NEON (Advanced SIMD) extensions
+
+config CRYPTO_POLY1305_NEON
+	tristate "Hash functions: Poly1305 (NEON)"
+	depends on KERNEL_MODE_NEON
 	select CRYPTO_HASH
+	select CRYPTO_ARCH_HAVE_LIB_POLY1305
+	help
+	  Poly1305 authenticator algorithm (RFC7539)
+
+	  Architecture: arm64 using:
+	  - NEON (Advanced SIMD) extensions
 
 config CRYPTO_SHA1_ARM64_CE
-	tristate "SHA-1 digest algorithm (ARMv8 Crypto Extensions)"
+	tristate "Hash functions: SHA-1 (ARMv8 Crypto Extensions)"
 	depends on KERNEL_MODE_NEON
 	select CRYPTO_HASH
 	select CRYPTO_SHA1
+	help
+	  SHA-1 secure hash algorithm (FIPS 180)
+
+	  Architecture: arm64 using:
+	  - ARMv8 Crypto Extensions
+
+config CRYPTO_SHA256_ARM64
+	tristate "Hash functions: SHA-224 and SHA-256"
+	select CRYPTO_HASH
+	help
+	  SHA-224 and SHA-256 secure hash algorithms (FIPS 180)
+
+	  Architecture: arm64
 
 config CRYPTO_SHA2_ARM64_CE
-	tristate "SHA-224/SHA-256 digest algorithm (ARMv8 Crypto Extensions)"
+	tristate "Hash functions: SHA-224 and SHA-256 (ARMv8 Crypto Extensions)"
 	depends on KERNEL_MODE_NEON
 	select CRYPTO_HASH
 	select CRYPTO_SHA256_ARM64
+	help
+	  SHA-224 and SHA-256 secure hash algorithms (FIPS 180)
+
+	  Architecture: arm64 using:
+	  - ARMv8 Crypto Extensions
+
+config CRYPTO_SHA512_ARM64
+	tristate "Hash functions: SHA-384 and SHA-512"
+	select CRYPTO_HASH
+	help
+	  SHA-384 and SHA-512 secure hash algorithms (FIPS 180)
+
+	  Architecture: arm64
 
 config CRYPTO_SHA512_ARM64_CE
-	tristate "SHA-384/SHA-512 digest algorithm (ARMv8 Crypto Extensions)"
+	tristate "Hash functions: SHA-384 and SHA-512 (ARMv8 Crypto Extensions)"
 	depends on KERNEL_MODE_NEON
 	select CRYPTO_HASH
 	select CRYPTO_SHA512_ARM64
+	help
+	  SHA-384 and SHA-512 secure hash algorithms (FIPS 180)
+
+	  Architecture: arm64 using:
+	  - ARMv8 Crypto Extensions
 
 config CRYPTO_SHA3_ARM64
-	tristate "SHA3 digest algorithm (ARMv8.2 Crypto Extensions)"
+	tristate "Hash functions: SHA-3 (ARMv8.2 Crypto Extensions)"
 	depends on KERNEL_MODE_NEON
 	select CRYPTO_HASH
 	select CRYPTO_SHA3
+	help
+	  SHA-3 secure hash algorithms (FIPS 202)
+
+	  Architecture: arm64 using:
+	  - ARMv8.2 Crypto Extensions
 
 config CRYPTO_SM3_ARM64_CE
-	tristate "SM3 digest algorithm (ARMv8.2 Crypto Extensions)"
+	tristate "Hash functions: SM3 (ARMv8.2 Crypto Extensions)"
 	depends on KERNEL_MODE_NEON
 	select CRYPTO_HASH
 	select CRYPTO_SM3
+	help
+	  SM3 (ShangMi 3) secure hash function (OSCCA GM/T 0004-2012)
 
-config CRYPTO_SM4_ARM64_CE
-	tristate "SM4 symmetric cipher (ARMv8.2 Crypto Extensions)"
-	depends on KERNEL_MODE_NEON
-	select CRYPTO_ALGAPI
-	select CRYPTO_LIB_SM4
+	  Architecture: arm64 using:
+	  - ARMv8.2 Crypto Extensions
 
-config CRYPTO_GHASH_ARM64_CE
-	tristate "GHASH/AES-GCM using ARMv8 Crypto Extensions"
+config CRYPTO_POLYVAL_ARM64_CE
+	tristate "Hash functions: POLYVAL (ARMv8 Crypto Extensions)"
 	depends on KERNEL_MODE_NEON
-	select CRYPTO_HASH
-	select CRYPTO_GF128MUL
-	select CRYPTO_LIB_AES
+	select CRYPTO_POLYVAL
+	help
+	  POLYVAL hash function for HCTR2
 
-config CRYPTO_CRCT10DIF_ARM64_CE
-	tristate "CRCT10DIF digest algorithm using PMULL instructions"
-	depends on KERNEL_MODE_NEON && CRC_T10DIF
-	select CRYPTO_HASH
+	  Architecture: arm64 using:
+	  - ARMv8 Crypto Extensions
 
 config CRYPTO_AES_ARM64
-	tristate "AES core cipher using scalar instructions"
+	tristate "Ciphers: AES, modes: ECB, CBC, CTR, CTS, XCTR, XTS"
 	select CRYPTO_AES
+	help
+	  Block ciphers: AES cipher algorithms (FIPS-197)
+	  Length-preserving ciphers: AES with ECB, CBC, CTR, CTS,
+	    XCTR, and XTS modes
+	  AEAD cipher: AES with CBC, ESSIV, and SHA-256
+	    for fscrypt and dm-crypt
+
+	  Architecture: arm64
 
 config CRYPTO_AES_ARM64_CE
-	tristate "AES core cipher using ARMv8 Crypto Extensions"
+	tristate "Ciphers: AES (ARMv8 Crypto Extensions)"
 	depends on ARM64 && KERNEL_MODE_NEON
 	select CRYPTO_ALGAPI
 	select CRYPTO_LIB_AES
+	help
+	  Block ciphers: AES cipher algorithms (FIPS-197)
 
-config CRYPTO_AES_ARM64_CE_CCM
-	tristate "AES in CCM mode using ARMv8 Crypto Extensions"
-	depends on ARM64 && KERNEL_MODE_NEON
-	select CRYPTO_ALGAPI
-	select CRYPTO_AES_ARM64_CE
-	select CRYPTO_AEAD
-	select CRYPTO_LIB_AES
+	  Architecture: arm64 using:
+	  - ARMv8 Crypto Extensions
 
 config CRYPTO_AES_ARM64_CE_BLK
-	tristate "AES in ECB/CBC/CTR/XTS modes using ARMv8 Crypto Extensions"
+	tristate "Ciphers: AES, modes: ECB/CBC/CTR/XTS (ARMv8 Crypto Extensions)"
 	depends on KERNEL_MODE_NEON
 	select CRYPTO_SKCIPHER
 	select CRYPTO_AES_ARM64_CE
+	help
+	  Length-preserving ciphers: AES cipher algorithms (FIPS-197)
+	  with block cipher modes:
+	  - ECB (Electronic Codebook) mode (NIST SP800-38A)
+	  - CBC (Cipher Block Chaining) mode (NIST SP800-38A)
+	  - CTR (Counter) mode (NIST SP800-38A)
+	  - XTS (XOR Encrypt XOR with ciphertext stealing) mode (NIST SP800-38E
+	    and IEEE 1619)
+
+	  Architecture: arm64 using:
+	  - ARMv8 Crypto Extensions
 
 config CRYPTO_AES_ARM64_NEON_BLK
-	tristate "AES in ECB/CBC/CTR/XTS modes using NEON instructions"
+	tristate "Ciphers: AES, modes: ECB/CBC/CTR/XTS (NEON)"
 	depends on KERNEL_MODE_NEON
 	select CRYPTO_SKCIPHER
 	select CRYPTO_LIB_AES
+	help
+	  Length-preserving ciphers: AES cipher algorithms (FIPS-197)
+	  with block cipher modes:
+	  - ECB (Electronic Codebook) mode (NIST SP800-38A)
+	  - CBC (Cipher Block Chaining) mode (NIST SP800-38A)
+	  - CTR (Counter) mode (NIST SP800-38A)
+	  - XTS (XOR Encrypt XOR with ciphertext stealing) mode (NIST SP800-38E
+	    and IEEE 1619)
+
+	  Architecture: arm64 using:
+	  - NEON (Advanced SIMD) extensions
 
 config CRYPTO_CHACHA20_NEON
-	tristate "ChaCha20, XChaCha20, and XChaCha12 stream ciphers using NEON instructions"
+	tristate "Ciphers: ChaCha (NEON)"
 	depends on KERNEL_MODE_NEON
 	select CRYPTO_SKCIPHER
 	select CRYPTO_LIB_CHACHA_GENERIC
 	select CRYPTO_ARCH_HAVE_LIB_CHACHA
+	help
+	  Length-preserving ciphers: ChaCha20, XChaCha20, and XChaCha12
+	  stream cipher algorithms
 
-config CRYPTO_POLY1305_NEON
-	tristate "Poly1305 hash function using scalar or NEON instructions"
+	  Architecture: arm64 using:
+	  - NEON (Advanced SIMD) extensions
+
+config CRYPTO_AES_ARM64_BS
+	tristate "Ciphers: AES, modes: ECB/CBC/CTR/XCTR/XTS modes (bit-sliced NEON)"
 	depends on KERNEL_MODE_NEON
-	select CRYPTO_HASH
-	select CRYPTO_ARCH_HAVE_LIB_POLY1305
+	select CRYPTO_SKCIPHER
+	select CRYPTO_AES_ARM64_NEON_BLK
+	select CRYPTO_LIB_AES
+	help
+	  Length-preserving ciphers: AES cipher algorithms (FIPS-197)
+	  with block cipher modes:
+	  - ECB (Electronic Codebook) mode (NIST SP800-38A)
+	  - CBC (Cipher Block Chaining) mode (NIST SP800-38A)
+	  - CTR (Counter) mode (NIST SP800-38A)
+	  - XCTR mode for HCTR2
+	  - XTS (XOR Encrypt XOR with ciphertext stealing) mode (NIST SP800-38E
+	    and IEEE 1619)
 
-config CRYPTO_NHPOLY1305_NEON
-	tristate "NHPoly1305 hash function using NEON instructions (for Adiantum)"
+	  Architecture: arm64 using:
+	  - bit-sliced algorithm
+	  - NEON (Advanced SIMD) extensions
+
+config CRYPTO_SM4_ARM64_CE
+	tristate "Ciphers: SM4 (ARMv8.2 Crypto Extensions)"
 	depends on KERNEL_MODE_NEON
-	select CRYPTO_NHPOLY1305
+	select CRYPTO_ALGAPI
+	select CRYPTO_SM4
+	help
+	  Block ciphers: SM4 cipher algorithms (OSCCA GB/T 32907-2016)
 
-config CRYPTO_AES_ARM64_BS
-	tristate "AES in ECB/CBC/CTR/XTS modes using bit-sliced NEON algorithm"
+	  Architecture: arm64 using:
+	  - ARMv8.2 Crypto Extensions
+	  - NEON (Advanced SIMD) extensions
+
+config CRYPTO_SM4_ARM64_CE_BLK
+	tristate "Ciphers: SM4, modes: ECB/CBC/CFB/CTR (ARMv8 Crypto Extensions)"
 	depends on KERNEL_MODE_NEON
 	select CRYPTO_SKCIPHER
-	select CRYPTO_AES_ARM64_NEON_BLK
+	select CRYPTO_SM4
+	help
+	  Length-preserving ciphers: SM4 cipher algorithms (OSCCA GB/T 32907-2016)
+	  with block cipher modes:
+	  - ECB (Electronic Codebook) mode (NIST SP800-38A)
+	  - CBC (Cipher Block Chaining) mode (NIST SP800-38A)
+	  - CFB (Cipher Feedback) mode (NIST SP800-38A)
+	  - CTR (Counter) mode (NIST SP800-38A)
+
+	  Architecture: arm64 using:
+	  - ARMv8 Crypto Extensions
+	  - NEON (Advanced SIMD) extensions
+
+config CRYPTO_SM4_ARM64_NEON_BLK
+	tristate "Ciphers: SM4, modes: ECB/CBC/CFB/CTR (NEON)"
+	depends on KERNEL_MODE_NEON
+	select CRYPTO_SKCIPHER
+	select CRYPTO_SM4
+	help
+	  Length-preserving ciphers: SM4 cipher algorithms (OSCCA GB/T 32907-2016)
+	  with block cipher modes:
+	  - ECB (Electronic Codebook) mode (NIST SP800-38A)
+	  - CBC (Cipher Block Chaining) mode (NIST SP800-38A)
+	  - CFB (Cipher Feedback) mode (NIST SP800-38A)
+	  - CTR (Counter) mode (NIST SP800-38A)
+
+	  Architecture: arm64 using:
+	  - NEON (Advanced SIMD) extensions
+
+config CRYPTO_AES_ARM64_CE_CCM
+	tristate "AEAD cipher: AES in CCM mode (ARMv8 Crypto Extensions)"
+	depends on ARM64 && KERNEL_MODE_NEON
+	select CRYPTO_ALGAPI
+	select CRYPTO_AES_ARM64_CE
+	select CRYPTO_AEAD
 	select CRYPTO_LIB_AES
+	help
+	  AEAD cipher: AES cipher algorithms (FIPS-197) with
+	  CCM (Counter with Cipher Block Chaining-Message Authentication Code)
+	  authenticated encryption mode (NIST SP800-38C)
+
+	  Architecture: arm64 using:
+	  - ARMv8 Crypto Extensions
+	  - NEON (Advanced SIMD) extensions
+
+config CRYPTO_CRCT10DIF_ARM64_CE
+	tristate "CRCT10DIF (PMULL)"
+	depends on KERNEL_MODE_NEON && CRC_T10DIF
+	select CRYPTO_HASH
+	help
+	  CRC16 CRC algorithm used for the T10 (SCSI) Data Integrity Field (DIF)
+
+	  Architecture: arm64 using
+	  - PMULL (Polynomial Multiply Long) instructions
+
+endmenu
 
-endif
diff --git a/arch/arm64/crypto/Makefile b/arch/arm64/crypto/Makefile
index 09a805cc32d7..24bb0c4610de 100644
--- a/arch/arm64/crypto/Makefile
+++ b/arch/arm64/crypto/Makefile
@@ -20,12 +20,21 @@ sha3-ce-y := sha3-ce-glue.o sha3-ce-core.o
 obj-$(CONFIG_CRYPTO_SM3_ARM64_CE) += sm3-ce.o
 sm3-ce-y := sm3-ce-glue.o sm3-ce-core.o
 
-obj-$(CONFIG_CRYPTO_SM4_ARM64_CE) += sm4-ce.o
+obj-$(CONFIG_CRYPTO_SM4_ARM64_CE) += sm4-ce-cipher.o
+sm4-ce-cipher-y := sm4-ce-cipher-glue.o sm4-ce-cipher-core.o
+
+obj-$(CONFIG_CRYPTO_SM4_ARM64_CE_BLK) += sm4-ce.o
 sm4-ce-y := sm4-ce-glue.o sm4-ce-core.o
 
+obj-$(CONFIG_CRYPTO_SM4_ARM64_NEON_BLK) += sm4-neon.o
+sm4-neon-y := sm4-neon-glue.o sm4-neon-core.o
+
 obj-$(CONFIG_CRYPTO_GHASH_ARM64_CE) += ghash-ce.o
 ghash-ce-y := ghash-ce-glue.o ghash-ce-core.o
 
+obj-$(CONFIG_CRYPTO_POLYVAL_ARM64_CE) += polyval-ce.o
+polyval-ce-y := polyval-ce-glue.o polyval-ce-core.o
+
 obj-$(CONFIG_CRYPTO_CRCT10DIF_ARM64_CE) += crct10dif-ce.o
 crct10dif-ce-y := crct10dif-ce-core.o crct10dif-ce-glue.o
 
diff --git a/arch/arm64/crypto/aes-glue.c b/arch/arm64/crypto/aes-glue.c
index 30b7cc6a7079..162787c7aa86 100644
--- a/arch/arm64/crypto/aes-glue.c
+++ b/arch/arm64/crypto/aes-glue.c
@@ -24,7 +24,6 @@
 #ifdef USE_V8_CRYPTO_EXTENSIONS
 #define MODE			"ce"
 #define PRIO			300
-#define STRIDE			5
 #define aes_expandkey		ce_aes_expandkey
 #define aes_ecb_encrypt		ce_aes_ecb_encrypt
 #define aes_ecb_decrypt		ce_aes_ecb_decrypt
@@ -35,14 +34,14 @@
 #define aes_essiv_cbc_encrypt	ce_aes_essiv_cbc_encrypt
 #define aes_essiv_cbc_decrypt	ce_aes_essiv_cbc_decrypt
 #define aes_ctr_encrypt		ce_aes_ctr_encrypt
+#define aes_xctr_encrypt	ce_aes_xctr_encrypt
 #define aes_xts_encrypt		ce_aes_xts_encrypt
 #define aes_xts_decrypt		ce_aes_xts_decrypt
 #define aes_mac_update		ce_aes_mac_update
-MODULE_DESCRIPTION("AES-ECB/CBC/CTR/XTS using ARMv8 Crypto Extensions");
+MODULE_DESCRIPTION("AES-ECB/CBC/CTR/XTS/XCTR using ARMv8 Crypto Extensions");
 #else
 #define MODE			"neon"
 #define PRIO			200
-#define STRIDE			4
 #define aes_ecb_encrypt		neon_aes_ecb_encrypt
 #define aes_ecb_decrypt		neon_aes_ecb_decrypt
 #define aes_cbc_encrypt		neon_aes_cbc_encrypt
@@ -52,16 +51,18 @@ MODULE_DESCRIPTION("AES-ECB/CBC/CTR/XTS using ARMv8 Crypto Extensions");
 #define aes_essiv_cbc_encrypt	neon_aes_essiv_cbc_encrypt
 #define aes_essiv_cbc_decrypt	neon_aes_essiv_cbc_decrypt
 #define aes_ctr_encrypt		neon_aes_ctr_encrypt
+#define aes_xctr_encrypt	neon_aes_xctr_encrypt
 #define aes_xts_encrypt		neon_aes_xts_encrypt
 #define aes_xts_decrypt		neon_aes_xts_decrypt
 #define aes_mac_update		neon_aes_mac_update
-MODULE_DESCRIPTION("AES-ECB/CBC/CTR/XTS using ARMv8 NEON");
+MODULE_DESCRIPTION("AES-ECB/CBC/CTR/XTS/XCTR using ARMv8 NEON");
 #endif
 #if defined(USE_V8_CRYPTO_EXTENSIONS) || !IS_ENABLED(CONFIG_CRYPTO_AES_ARM64_BS)
 MODULE_ALIAS_CRYPTO("ecb(aes)");
 MODULE_ALIAS_CRYPTO("cbc(aes)");
 MODULE_ALIAS_CRYPTO("ctr(aes)");
 MODULE_ALIAS_CRYPTO("xts(aes)");
+MODULE_ALIAS_CRYPTO("xctr(aes)");
 #endif
 MODULE_ALIAS_CRYPTO("cts(cbc(aes))");
 MODULE_ALIAS_CRYPTO("essiv(cbc(aes),sha256)");
@@ -89,7 +90,10 @@ asmlinkage void aes_cbc_cts_decrypt(u8 out[], u8 const in[], u32 const rk[],
 				int rounds, int bytes, u8 const iv[]);
 
 asmlinkage void aes_ctr_encrypt(u8 out[], u8 const in[], u32 const rk[],
-				int rounds, int bytes, u8 ctr[], u8 finalbuf[]);
+				int rounds, int bytes, u8 ctr[]);
+
+asmlinkage void aes_xctr_encrypt(u8 out[], u8 const in[], u32 const rk[],
+				 int rounds, int bytes, u8 ctr[], int byte_ctr);
 
 asmlinkage void aes_xts_encrypt(u8 out[], u8 const in[], u32 const rk1[],
 				int rounds, int bytes, u32 const rk2[], u8 iv[],
@@ -444,6 +448,52 @@ static int __maybe_unused essiv_cbc_decrypt(struct skcipher_request *req)
 	return err ?: cbc_decrypt_walk(req, &walk);
 }
 
+static int __maybe_unused xctr_encrypt(struct skcipher_request *req)
+{
+	struct crypto_skcipher *tfm = crypto_skcipher_reqtfm(req);
+	struct crypto_aes_ctx *ctx = crypto_skcipher_ctx(tfm);
+	int err, rounds = 6 + ctx->key_length / 4;
+	struct skcipher_walk walk;
+	unsigned int byte_ctr = 0;
+
+	err = skcipher_walk_virt(&walk, req, false);
+
+	while (walk.nbytes > 0) {
+		const u8 *src = walk.src.virt.addr;
+		unsigned int nbytes = walk.nbytes;
+		u8 *dst = walk.dst.virt.addr;
+		u8 buf[AES_BLOCK_SIZE];
+
+		/*
+		 * If given less than 16 bytes, we must copy the partial block
+		 * into a temporary buffer of 16 bytes to avoid out of bounds
+		 * reads and writes.  Furthermore, this code is somewhat unusual
+		 * in that it expects the end of the data to be at the end of
+		 * the temporary buffer, rather than the start of the data at
+		 * the start of the temporary buffer.
+		 */
+		if (unlikely(nbytes < AES_BLOCK_SIZE))
+			src = dst = memcpy(buf + sizeof(buf) - nbytes,
+					   src, nbytes);
+		else if (nbytes < walk.total)
+			nbytes &= ~(AES_BLOCK_SIZE - 1);
+
+		kernel_neon_begin();
+		aes_xctr_encrypt(dst, src, ctx->key_enc, rounds, nbytes,
+						 walk.iv, byte_ctr);
+		kernel_neon_end();
+
+		if (unlikely(nbytes < AES_BLOCK_SIZE))
+			memcpy(walk.dst.virt.addr,
+			       buf + sizeof(buf) - nbytes, nbytes);
+		byte_ctr += nbytes;
+
+		err = skcipher_walk_done(&walk, walk.nbytes - nbytes);
+	}
+
+	return err;
+}
+
 static int __maybe_unused ctr_encrypt(struct skcipher_request *req)
 {
 	struct crypto_skcipher *tfm = crypto_skcipher_reqtfm(req);
@@ -458,26 +508,29 @@ static int __maybe_unused ctr_encrypt(struct skcipher_request *req)
 		unsigned int nbytes = walk.nbytes;
 		u8 *dst = walk.dst.virt.addr;
 		u8 buf[AES_BLOCK_SIZE];
-		unsigned int tail;
 
+		/*
+		 * If given less than 16 bytes, we must copy the partial block
+		 * into a temporary buffer of 16 bytes to avoid out of bounds
+		 * reads and writes.  Furthermore, this code is somewhat unusual
+		 * in that it expects the end of the data to be at the end of
+		 * the temporary buffer, rather than the start of the data at
+		 * the start of the temporary buffer.
+		 */
 		if (unlikely(nbytes < AES_BLOCK_SIZE))
-			src = memcpy(buf, src, nbytes);
+			src = dst = memcpy(buf + sizeof(buf) - nbytes,
+					   src, nbytes);
 		else if (nbytes < walk.total)
 			nbytes &= ~(AES_BLOCK_SIZE - 1);
 
 		kernel_neon_begin();
 		aes_ctr_encrypt(dst, src, ctx->key_enc, rounds, nbytes,
-				walk.iv, buf);
+				walk.iv);
 		kernel_neon_end();
 
-		tail = nbytes % (STRIDE * AES_BLOCK_SIZE);
-		if (tail > 0 && tail < AES_BLOCK_SIZE)
-			/*
-			 * The final partial block could not be returned using
-			 * an overlapping store, so it was passed via buf[]
-			 * instead.
-			 */
-			memcpy(dst + nbytes - tail, buf, tail);
+		if (unlikely(nbytes < AES_BLOCK_SIZE))
+			memcpy(walk.dst.virt.addr,
+			       buf + sizeof(buf) - nbytes, nbytes);
 
 		err = skcipher_walk_done(&walk, walk.nbytes - nbytes);
 	}
@@ -678,6 +731,22 @@ static struct skcipher_alg aes_algs[] = { {
 	.decrypt	= ctr_encrypt,
 }, {
 	.base = {
+		.cra_name		= "xctr(aes)",
+		.cra_driver_name	= "xctr-aes-" MODE,
+		.cra_priority		= PRIO,
+		.cra_blocksize		= 1,
+		.cra_ctxsize		= sizeof(struct crypto_aes_ctx),
+		.cra_module		= THIS_MODULE,
+	},
+	.min_keysize	= AES_MIN_KEY_SIZE,
+	.max_keysize	= AES_MAX_KEY_SIZE,
+	.ivsize		= AES_BLOCK_SIZE,
+	.chunksize	= AES_BLOCK_SIZE,
+	.setkey		= skcipher_aes_setkey,
+	.encrypt	= xctr_encrypt,
+	.decrypt	= xctr_encrypt,
+}, {
+	.base = {
 		.cra_name		= "xts(aes)",
 		.cra_driver_name	= "xts-aes-" MODE,
 		.cra_priority		= PRIO,
@@ -983,6 +1052,7 @@ module_cpu_feature_match(AES, aes_init);
 module_init(aes_init);
 EXPORT_SYMBOL(neon_aes_ecb_encrypt);
 EXPORT_SYMBOL(neon_aes_cbc_encrypt);
+EXPORT_SYMBOL(neon_aes_ctr_encrypt);
 EXPORT_SYMBOL(neon_aes_xts_encrypt);
 EXPORT_SYMBOL(neon_aes_xts_decrypt);
 #endif
diff --git a/arch/arm64/crypto/aes-modes.S b/arch/arm64/crypto/aes-modes.S
index b495de22bb38..5abc834271f4 100644
--- a/arch/arm64/crypto/aes-modes.S
+++ b/arch/arm64/crypto/aes-modes.S
@@ -318,127 +318,211 @@ AES_FUNC_END(aes_cbc_cts_decrypt)
 	.byte		0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff, 0xff
 	.previous
 
-
 	/*
-	 * aes_ctr_encrypt(u8 out[], u8 const in[], u8 const rk[], int rounds,
-	 *		   int bytes, u8 ctr[], u8 finalbuf[])
+	 * This macro generates the code for CTR and XCTR mode.
 	 */
+.macro ctr_encrypt xctr
+	// Arguments
+	OUT		.req x0
+	IN		.req x1
+	KEY		.req x2
+	ROUNDS_W	.req w3
+	BYTES_W		.req w4
+	IV		.req x5
+	BYTE_CTR_W 	.req w6		// XCTR only
+	// Intermediate values
+	CTR_W		.req w11	// XCTR only
+	CTR		.req x11	// XCTR only
+	IV_PART		.req x12
+	BLOCKS		.req x13
+	BLOCKS_W	.req w13
 
-AES_FUNC_START(aes_ctr_encrypt)
 	stp		x29, x30, [sp, #-16]!
 	mov		x29, sp
 
-	enc_prepare	w3, x2, x12
-	ld1		{vctr.16b}, [x5]
-
-	umov		x12, vctr.d[1]		/* keep swabbed ctr in reg */
-	rev		x12, x12
+	enc_prepare	ROUNDS_W, KEY, IV_PART
+	ld1		{vctr.16b}, [IV]
 
-.LctrloopNx:
-	add		w7, w4, #15
-	sub		w4, w4, #MAX_STRIDE << 4
-	lsr		w7, w7, #4
+	/*
+	 * Keep 64 bits of the IV in a register.  For CTR mode this lets us
+	 * easily increment the IV.  For XCTR mode this lets us efficiently XOR
+	 * the 64-bit counter with the IV.
+	 */
+	.if \xctr
+		umov		IV_PART, vctr.d[0]
+		lsr		CTR_W, BYTE_CTR_W, #4
+	.else
+		umov		IV_PART, vctr.d[1]
+		rev		IV_PART, IV_PART
+	.endif
+
+.LctrloopNx\xctr:
+	add		BLOCKS_W, BYTES_W, #15
+	sub		BYTES_W, BYTES_W, #MAX_STRIDE << 4
+	lsr		BLOCKS_W, BLOCKS_W, #4
 	mov		w8, #MAX_STRIDE
-	cmp		w7, w8
-	csel		w7, w7, w8, lt
-	adds		x12, x12, x7
+	cmp		BLOCKS_W, w8
+	csel		BLOCKS_W, BLOCKS_W, w8, lt
 
+	/*
+	 * Set up the counter values in v0-v{MAX_STRIDE-1}.
+	 *
+	 * If we are encrypting less than MAX_STRIDE blocks, the tail block
+	 * handling code expects the last keystream block to be in
+	 * v{MAX_STRIDE-1}.  For example: if encrypting two blocks with
+	 * MAX_STRIDE=5, then v3 and v4 should have the next two counter blocks.
+	 */
+	.if \xctr
+		add		CTR, CTR, BLOCKS
+	.else
+		adds		IV_PART, IV_PART, BLOCKS
+	.endif
 	mov		v0.16b, vctr.16b
 	mov		v1.16b, vctr.16b
 	mov		v2.16b, vctr.16b
 	mov		v3.16b, vctr.16b
 ST5(	mov		v4.16b, vctr.16b		)
-	bcs		0f
-
-	.subsection	1
-	/* apply carry to outgoing counter */
-0:	umov		x8, vctr.d[0]
-	rev		x8, x8
-	add		x8, x8, #1
-	rev		x8, x8
-	ins		vctr.d[0], x8
-
-	/* apply carry to N counter blocks for N := x12 */
-	cbz		x12, 2f
-	adr		x16, 1f
-	sub		x16, x16, x12, lsl #3
-	br		x16
-	hint		34			// bti c
-	mov		v0.d[0], vctr.d[0]
-	hint		34			// bti c
-	mov		v1.d[0], vctr.d[0]
-	hint		34			// bti c
-	mov		v2.d[0], vctr.d[0]
-	hint		34			// bti c
-	mov		v3.d[0], vctr.d[0]
-ST5(	hint		34				)
-ST5(	mov		v4.d[0], vctr.d[0]		)
-1:	b		2f
-	.previous
+	.if \xctr
+		sub		x6, CTR, #MAX_STRIDE - 1
+		sub		x7, CTR, #MAX_STRIDE - 2
+		sub		x8, CTR, #MAX_STRIDE - 3
+		sub		x9, CTR, #MAX_STRIDE - 4
+ST5(		sub		x10, CTR, #MAX_STRIDE - 5	)
+		eor		x6, x6, IV_PART
+		eor		x7, x7, IV_PART
+		eor		x8, x8, IV_PART
+		eor		x9, x9, IV_PART
+ST5(		eor		x10, x10, IV_PART		)
+		mov		v0.d[0], x6
+		mov		v1.d[0], x7
+		mov		v2.d[0], x8
+		mov		v3.d[0], x9
+ST5(		mov		v4.d[0], x10			)
+	.else
+		bcs		0f
+		.subsection	1
+		/*
+		 * This subsection handles carries.
+		 *
+		 * Conditional branching here is allowed with respect to time
+		 * invariance since the branches are dependent on the IV instead
+		 * of the plaintext or key.  This code is rarely executed in
+		 * practice anyway.
+		 */
+
+		/* Apply carry to outgoing counter. */
+0:		umov		x8, vctr.d[0]
+		rev		x8, x8
+		add		x8, x8, #1
+		rev		x8, x8
+		ins		vctr.d[0], x8
+
+		/*
+		 * Apply carry to counter blocks if needed.
+		 *
+		 * Since the carry flag was set, we know 0 <= IV_PART <
+		 * MAX_STRIDE.  Using the value of IV_PART we can determine how
+		 * many counter blocks need to be updated.
+		 */
+		cbz		IV_PART, 2f
+		adr		x16, 1f
+		sub		x16, x16, IV_PART, lsl #3
+		br		x16
+		bti		c
+		mov		v0.d[0], vctr.d[0]
+		bti		c
+		mov		v1.d[0], vctr.d[0]
+		bti		c
+		mov		v2.d[0], vctr.d[0]
+		bti		c
+		mov		v3.d[0], vctr.d[0]
+ST5(		bti		c				)
+ST5(		mov		v4.d[0], vctr.d[0]		)
+1:		b		2f
+		.previous
+
+2:		rev		x7, IV_PART
+		ins		vctr.d[1], x7
+		sub		x7, IV_PART, #MAX_STRIDE - 1
+		sub		x8, IV_PART, #MAX_STRIDE - 2
+		sub		x9, IV_PART, #MAX_STRIDE - 3
+		rev		x7, x7
+		rev		x8, x8
+		mov		v1.d[1], x7
+		rev		x9, x9
+ST5(		sub		x10, IV_PART, #MAX_STRIDE - 4	)
+		mov		v2.d[1], x8
+ST5(		rev		x10, x10			)
+		mov		v3.d[1], x9
+ST5(		mov		v4.d[1], x10			)
+	.endif
 
-2:	rev		x7, x12
-	ins		vctr.d[1], x7
-	sub		x7, x12, #MAX_STRIDE - 1
-	sub		x8, x12, #MAX_STRIDE - 2
-	sub		x9, x12, #MAX_STRIDE - 3
-	rev		x7, x7
-	rev		x8, x8
-	mov		v1.d[1], x7
-	rev		x9, x9
-ST5(	sub		x10, x12, #MAX_STRIDE - 4	)
-	mov		v2.d[1], x8
-ST5(	rev		x10, x10			)
-	mov		v3.d[1], x9
-ST5(	mov		v4.d[1], x10			)
-	tbnz		w4, #31, .Lctrtail
-	ld1		{v5.16b-v7.16b}, [x1], #48
+	/*
+	 * If there are at least MAX_STRIDE blocks left, XOR the data with
+	 * keystream and store.  Otherwise jump to tail handling.
+	 */
+	tbnz		BYTES_W, #31, .Lctrtail\xctr
+	ld1		{v5.16b-v7.16b}, [IN], #48
 ST4(	bl		aes_encrypt_block4x		)
 ST5(	bl		aes_encrypt_block5x		)
 	eor		v0.16b, v5.16b, v0.16b
-ST4(	ld1		{v5.16b}, [x1], #16		)
+ST4(	ld1		{v5.16b}, [IN], #16		)
 	eor		v1.16b, v6.16b, v1.16b
-ST5(	ld1		{v5.16b-v6.16b}, [x1], #32	)
+ST5(	ld1		{v5.16b-v6.16b}, [IN], #32	)
 	eor		v2.16b, v7.16b, v2.16b
 	eor		v3.16b, v5.16b, v3.16b
 ST5(	eor		v4.16b, v6.16b, v4.16b		)
-	st1		{v0.16b-v3.16b}, [x0], #64
-ST5(	st1		{v4.16b}, [x0], #16		)
-	cbz		w4, .Lctrout
-	b		.LctrloopNx
-
-.Lctrout:
-	st1		{vctr.16b}, [x5]	/* return next CTR value */
+	st1		{v0.16b-v3.16b}, [OUT], #64
+ST5(	st1		{v4.16b}, [OUT], #16		)
+	cbz		BYTES_W, .Lctrout\xctr
+	b		.LctrloopNx\xctr
+
+.Lctrout\xctr:
+	.if !\xctr
+		st1		{vctr.16b}, [IV] /* return next CTR value */
+	.endif
 	ldp		x29, x30, [sp], #16
 	ret
 
-.Lctrtail:
-	/* XOR up to MAX_STRIDE * 16 - 1 bytes of in/output with v0 ... v3/v4 */
+.Lctrtail\xctr:
+	/*
+	 * Handle up to MAX_STRIDE * 16 - 1 bytes of plaintext
+	 *
+	 * This code expects the last keystream block to be in v{MAX_STRIDE-1}.
+	 * For example: if encrypting two blocks with MAX_STRIDE=5, then v3 and
+	 * v4 should have the next two counter blocks.
+	 *
+	 * This allows us to store the ciphertext by writing to overlapping
+	 * regions of memory.  Any invalid ciphertext blocks get overwritten by
+	 * correctly computed blocks.  This approach greatly simplifies the
+	 * logic for storing the ciphertext.
+	 */
 	mov		x16, #16
-	ands		x13, x4, #0xf
-	csel		x13, x13, x16, ne
+	ands		w7, BYTES_W, #0xf
+	csel		x13, x7, x16, ne
 
-ST5(	cmp		w4, #64 - (MAX_STRIDE << 4)	)
+ST5(	cmp		BYTES_W, #64 - (MAX_STRIDE << 4))
 ST5(	csel		x14, x16, xzr, gt		)
-	cmp		w4, #48 - (MAX_STRIDE << 4)
+	cmp		BYTES_W, #48 - (MAX_STRIDE << 4)
 	csel		x15, x16, xzr, gt
-	cmp		w4, #32 - (MAX_STRIDE << 4)
+	cmp		BYTES_W, #32 - (MAX_STRIDE << 4)
 	csel		x16, x16, xzr, gt
-	cmp		w4, #16 - (MAX_STRIDE << 4)
-	ble		.Lctrtail1x
+	cmp		BYTES_W, #16 - (MAX_STRIDE << 4)
 
-	adr_l		x12, .Lcts_permute_table
-	add		x12, x12, x13
+	adr_l		x9, .Lcts_permute_table
+	add		x9, x9, x13
+	ble		.Lctrtail1x\xctr
 
-ST5(	ld1		{v5.16b}, [x1], x14		)
-	ld1		{v6.16b}, [x1], x15
-	ld1		{v7.16b}, [x1], x16
+ST5(	ld1		{v5.16b}, [IN], x14		)
+	ld1		{v6.16b}, [IN], x15
+	ld1		{v7.16b}, [IN], x16
 
 ST4(	bl		aes_encrypt_block4x		)
 ST5(	bl		aes_encrypt_block5x		)
 
-	ld1		{v8.16b}, [x1], x13
-	ld1		{v9.16b}, [x1]
-	ld1		{v10.16b}, [x12]
+	ld1		{v8.16b}, [IN], x13
+	ld1		{v9.16b}, [IN]
+	ld1		{v10.16b}, [x9]
 
 ST4(	eor		v6.16b, v6.16b, v0.16b		)
 ST4(	eor		v7.16b, v7.16b, v1.16b		)
@@ -453,24 +537,91 @@ ST5(	eor		v7.16b, v7.16b, v2.16b		)
 ST5(	eor		v8.16b, v8.16b, v3.16b		)
 ST5(	eor		v9.16b, v9.16b, v4.16b		)
 
-ST5(	st1		{v5.16b}, [x0], x14		)
-	st1		{v6.16b}, [x0], x15
-	st1		{v7.16b}, [x0], x16
-	add		x13, x13, x0
+ST5(	st1		{v5.16b}, [OUT], x14		)
+	st1		{v6.16b}, [OUT], x15
+	st1		{v7.16b}, [OUT], x16
+	add		x13, x13, OUT
 	st1		{v9.16b}, [x13]		// overlapping stores
-	st1		{v8.16b}, [x0]
-	b		.Lctrout
+	st1		{v8.16b}, [OUT]
+	b		.Lctrout\xctr
 
-.Lctrtail1x:
-	csel		x0, x0, x6, eq		// use finalbuf if less than a full block
-	ld1		{v5.16b}, [x1]
+.Lctrtail1x\xctr:
+	/*
+	 * Handle <= 16 bytes of plaintext
+	 *
+	 * This code always reads and writes 16 bytes.  To avoid out of bounds
+	 * accesses, XCTR and CTR modes must use a temporary buffer when
+	 * encrypting/decrypting less than 16 bytes.
+	 *
+	 * This code is unusual in that it loads the input and stores the output
+	 * relative to the end of the buffers rather than relative to the start.
+	 * This causes unusual behaviour when encrypting/decrypting less than 16
+	 * bytes; the end of the data is expected to be at the end of the
+	 * temporary buffer rather than the start of the data being at the start
+	 * of the temporary buffer.
+	 */
+	sub		x8, x7, #16
+	csel		x7, x7, x8, eq
+	add		IN, IN, x7
+	add		OUT, OUT, x7
+	ld1		{v5.16b}, [IN]
+	ld1		{v6.16b}, [OUT]
 ST5(	mov		v3.16b, v4.16b			)
-	encrypt_block	v3, w3, x2, x8, w7
+	encrypt_block	v3, ROUNDS_W, KEY, x8, w7
+	ld1		{v10.16b-v11.16b}, [x9]
+	tbl		v3.16b, {v3.16b}, v10.16b
+	sshr		v11.16b, v11.16b, #7
 	eor		v5.16b, v5.16b, v3.16b
-	st1		{v5.16b}, [x0]
-	b		.Lctrout
+	bif		v5.16b, v6.16b, v11.16b
+	st1		{v5.16b}, [OUT]
+	b		.Lctrout\xctr
+
+	// Arguments
+	.unreq OUT
+	.unreq IN
+	.unreq KEY
+	.unreq ROUNDS_W
+	.unreq BYTES_W
+	.unreq IV
+	.unreq BYTE_CTR_W	// XCTR only
+	// Intermediate values
+	.unreq CTR_W		// XCTR only
+	.unreq CTR		// XCTR only
+	.unreq IV_PART
+	.unreq BLOCKS
+	.unreq BLOCKS_W
+.endm
+
+	/*
+	 * aes_ctr_encrypt(u8 out[], u8 const in[], u8 const rk[], int rounds,
+	 *		   int bytes, u8 ctr[])
+	 *
+	 * The input and output buffers must always be at least 16 bytes even if
+	 * encrypting/decrypting less than 16 bytes.  Otherwise out of bounds
+	 * accesses will occur.  The data to be encrypted/decrypted is expected
+	 * to be at the end of this 16-byte temporary buffer rather than the
+	 * start.
+	 */
+
+AES_FUNC_START(aes_ctr_encrypt)
+	ctr_encrypt 0
 AES_FUNC_END(aes_ctr_encrypt)
 
+	/*
+	 * aes_xctr_encrypt(u8 out[], u8 const in[], u8 const rk[], int rounds,
+	 *		   int bytes, u8 const iv[], int byte_ctr)
+	 *
+	 * The input and output buffers must always be at least 16 bytes even if
+	 * encrypting/decrypting less than 16 bytes.  Otherwise out of bounds
+	 * accesses will occur.  The data to be encrypted/decrypted is expected
+	 * to be at the end of this 16-byte temporary buffer rather than the
+	 * start.
+	 */
+
+AES_FUNC_START(aes_xctr_encrypt)
+	ctr_encrypt 1
+AES_FUNC_END(aes_xctr_encrypt)
+
 
 	/*
 	 * aes_xts_encrypt(u8 out[], u8 const in[], u8 const rk1[], int rounds,
diff --git a/arch/arm64/crypto/aes-neon.S b/arch/arm64/crypto/aes-neon.S
index e47d3ec2cfb4..9de7fbc797af 100644
--- a/arch/arm64/crypto/aes-neon.S
+++ b/arch/arm64/crypto/aes-neon.S
@@ -66,7 +66,7 @@
 	prepare		crypto_aes_inv_sbox, .LReverse_ShiftRows, \temp
 	.endm
 
-	/* apply SubBytes transformation using the the preloaded Sbox */
+	/* apply SubBytes transformation using the preloaded Sbox */
 	.macro		sub_bytes, in
 	sub		v9.16b, \in\().16b, v15.16b
 	tbl		\in\().16b, {v16.16b-v19.16b}, \in\().16b
diff --git a/arch/arm64/crypto/aes-neonbs-core.S b/arch/arm64/crypto/aes-neonbs-core.S
index a3405b8c344b..d427f4556b6e 100644
--- a/arch/arm64/crypto/aes-neonbs-core.S
+++ b/arch/arm64/crypto/aes-neonbs-core.S
@@ -735,119 +735,67 @@ SYM_FUNC_END(aesbs_cbc_decrypt)
 	 *		     int blocks, u8 iv[])
 	 */
 SYM_FUNC_START_LOCAL(__xts_crypt8)
-	mov		x6, #1
-	lsl		x6, x6, x23
-	subs		w23, w23, #8
-	csel		x23, x23, xzr, pl
-	csel		x6, x6, xzr, mi
+	movi		v18.2s, #0x1
+	movi		v19.2s, #0x87
+	uzp1		v18.4s, v18.4s, v19.4s
+
+	ld1		{v0.16b-v3.16b}, [x1], #64
+	ld1		{v4.16b-v7.16b}, [x1], #64
+
+	next_tweak	v26, v25, v18, v19
+	next_tweak	v27, v26, v18, v19
+	next_tweak	v28, v27, v18, v19
+	next_tweak	v29, v28, v18, v19
+	next_tweak	v30, v29, v18, v19
+	next_tweak	v31, v30, v18, v19
+	next_tweak	v16, v31, v18, v19
+	next_tweak	v17, v16, v18, v19
 
-	ld1		{v0.16b}, [x20], #16
-	next_tweak	v26, v25, v30, v31
 	eor		v0.16b, v0.16b, v25.16b
-	tbnz		x6, #1, 0f
-
-	ld1		{v1.16b}, [x20], #16
-	next_tweak	v27, v26, v30, v31
 	eor		v1.16b, v1.16b, v26.16b
-	tbnz		x6, #2, 0f
-
-	ld1		{v2.16b}, [x20], #16
-	next_tweak	v28, v27, v30, v31
 	eor		v2.16b, v2.16b, v27.16b
-	tbnz		x6, #3, 0f
-
-	ld1		{v3.16b}, [x20], #16
-	next_tweak	v29, v28, v30, v31
 	eor		v3.16b, v3.16b, v28.16b
-	tbnz		x6, #4, 0f
-
-	ld1		{v4.16b}, [x20], #16
-	str		q29, [sp, #.Lframe_local_offset]
 	eor		v4.16b, v4.16b, v29.16b
-	next_tweak	v29, v29, v30, v31
-	tbnz		x6, #5, 0f
-
-	ld1		{v5.16b}, [x20], #16
-	str		q29, [sp, #.Lframe_local_offset + 16]
-	eor		v5.16b, v5.16b, v29.16b
-	next_tweak	v29, v29, v30, v31
-	tbnz		x6, #6, 0f
-
-	ld1		{v6.16b}, [x20], #16
-	str		q29, [sp, #.Lframe_local_offset + 32]
-	eor		v6.16b, v6.16b, v29.16b
-	next_tweak	v29, v29, v30, v31
-	tbnz		x6, #7, 0f
+	eor		v5.16b, v5.16b, v30.16b
+	eor		v6.16b, v6.16b, v31.16b
+	eor		v7.16b, v7.16b, v16.16b
 
-	ld1		{v7.16b}, [x20], #16
-	str		q29, [sp, #.Lframe_local_offset + 48]
-	eor		v7.16b, v7.16b, v29.16b
-	next_tweak	v29, v29, v30, v31
+	stp		q16, q17, [sp, #16]
 
-0:	mov		bskey, x21
-	mov		rounds, x22
+	mov		bskey, x2
+	mov		rounds, x3
 	br		x16
 SYM_FUNC_END(__xts_crypt8)
 
 	.macro		__xts_crypt, do8, o0, o1, o2, o3, o4, o5, o6, o7
-	frame_push	6, 64
-
-	mov		x19, x0
-	mov		x20, x1
-	mov		x21, x2
-	mov		x22, x3
-	mov		x23, x4
-	mov		x24, x5
+	stp		x29, x30, [sp, #-48]!
+	mov		x29, sp
 
-	movi		v30.2s, #0x1
-	movi		v25.2s, #0x87
-	uzp1		v30.4s, v30.4s, v25.4s
-	ld1		{v25.16b}, [x24]
+	ld1		{v25.16b}, [x5]
 
-99:	adr		x16, \do8
+0:	adr		x16, \do8
 	bl		__xts_crypt8
 
-	ldp		q16, q17, [sp, #.Lframe_local_offset]
-	ldp		q18, q19, [sp, #.Lframe_local_offset + 32]
+	eor		v16.16b, \o0\().16b, v25.16b
+	eor		v17.16b, \o1\().16b, v26.16b
+	eor		v18.16b, \o2\().16b, v27.16b
+	eor		v19.16b, \o3\().16b, v28.16b
 
-	eor		\o0\().16b, \o0\().16b, v25.16b
-	eor		\o1\().16b, \o1\().16b, v26.16b
-	eor		\o2\().16b, \o2\().16b, v27.16b
-	eor		\o3\().16b, \o3\().16b, v28.16b
+	ldp		q24, q25, [sp, #16]
 
-	st1		{\o0\().16b}, [x19], #16
-	mov		v25.16b, v26.16b
-	tbnz		x6, #1, 1f
-	st1		{\o1\().16b}, [x19], #16
-	mov		v25.16b, v27.16b
-	tbnz		x6, #2, 1f
-	st1		{\o2\().16b}, [x19], #16
-	mov		v25.16b, v28.16b
-	tbnz		x6, #3, 1f
-	st1		{\o3\().16b}, [x19], #16
-	mov		v25.16b, v29.16b
-	tbnz		x6, #4, 1f
+	eor		v20.16b, \o4\().16b, v29.16b
+	eor		v21.16b, \o5\().16b, v30.16b
+	eor		v22.16b, \o6\().16b, v31.16b
+	eor		v23.16b, \o7\().16b, v24.16b
 
-	eor		\o4\().16b, \o4\().16b, v16.16b
-	eor		\o5\().16b, \o5\().16b, v17.16b
-	eor		\o6\().16b, \o6\().16b, v18.16b
-	eor		\o7\().16b, \o7\().16b, v19.16b
+	st1		{v16.16b-v19.16b}, [x0], #64
+	st1		{v20.16b-v23.16b}, [x0], #64
 
-	st1		{\o4\().16b}, [x19], #16
-	tbnz		x6, #5, 1f
-	st1		{\o5\().16b}, [x19], #16
-	tbnz		x6, #6, 1f
-	st1		{\o6\().16b}, [x19], #16
-	tbnz		x6, #7, 1f
-	st1		{\o7\().16b}, [x19], #16
+	subs		x4, x4, #8
+	b.gt		0b
 
-	cbz		x23, 1f
-	st1		{v25.16b}, [x24]
-
-	b		99b
-
-1:	st1		{v25.16b}, [x24]
-	frame_pop
+	st1		{v25.16b}, [x5]
+	ldp		x29, x30, [sp], #48
 	ret
 	.endm
 
@@ -869,133 +817,51 @@ SYM_FUNC_END(aesbs_xts_decrypt)
 
 	/*
 	 * aesbs_ctr_encrypt(u8 out[], u8 const in[], u8 const rk[],
-	 *		     int rounds, int blocks, u8 iv[], u8 final[])
+	 *		     int rounds, int blocks, u8 iv[])
 	 */
 SYM_FUNC_START(aesbs_ctr_encrypt)
-	frame_push	8
-
-	mov		x19, x0
-	mov		x20, x1
-	mov		x21, x2
-	mov		x22, x3
-	mov		x23, x4
-	mov		x24, x5
-	mov		x25, x6
+	stp		x29, x30, [sp, #-16]!
+	mov		x29, sp
 
-	cmp		x25, #0
-	cset		x26, ne
-	add		x23, x23, x26		// do one extra block if final
-
-	ldp		x7, x8, [x24]
-	ld1		{v0.16b}, [x24]
+	ldp		x7, x8, [x5]
+	ld1		{v0.16b}, [x5]
 CPU_LE(	rev		x7, x7		)
 CPU_LE(	rev		x8, x8		)
 	adds		x8, x8, #1
 	adc		x7, x7, xzr
 
-99:	mov		x9, #1
-	lsl		x9, x9, x23
-	subs		w23, w23, #8
-	csel		x23, x23, xzr, pl
-	csel		x9, x9, xzr, le
-
-	tbnz		x9, #1, 0f
-	next_ctr	v1
-	tbnz		x9, #2, 0f
+0:	next_ctr	v1
 	next_ctr	v2
-	tbnz		x9, #3, 0f
 	next_ctr	v3
-	tbnz		x9, #4, 0f
 	next_ctr	v4
-	tbnz		x9, #5, 0f
 	next_ctr	v5
-	tbnz		x9, #6, 0f
 	next_ctr	v6
-	tbnz		x9, #7, 0f
 	next_ctr	v7
 
-0:	mov		bskey, x21
-	mov		rounds, x22
+	mov		bskey, x2
+	mov		rounds, x3
 	bl		aesbs_encrypt8
 
-	lsr		x9, x9, x26		// disregard the extra block
-	tbnz		x9, #0, 0f
-
-	ld1		{v8.16b}, [x20], #16
-	eor		v0.16b, v0.16b, v8.16b
-	st1		{v0.16b}, [x19], #16
-	tbnz		x9, #1, 1f
+	ld1		{ v8.16b-v11.16b}, [x1], #64
+	ld1		{v12.16b-v15.16b}, [x1], #64
 
-	ld1		{v9.16b}, [x20], #16
-	eor		v1.16b, v1.16b, v9.16b
-	st1		{v1.16b}, [x19], #16
-	tbnz		x9, #2, 2f
+	eor		v8.16b, v0.16b, v8.16b
+	eor		v9.16b, v1.16b, v9.16b
+	eor		v10.16b, v4.16b, v10.16b
+	eor		v11.16b, v6.16b, v11.16b
+	eor		v12.16b, v3.16b, v12.16b
+	eor		v13.16b, v7.16b, v13.16b
+	eor		v14.16b, v2.16b, v14.16b
+	eor		v15.16b, v5.16b, v15.16b
 
-	ld1		{v10.16b}, [x20], #16
-	eor		v4.16b, v4.16b, v10.16b
-	st1		{v4.16b}, [x19], #16
-	tbnz		x9, #3, 3f
+	st1		{ v8.16b-v11.16b}, [x0], #64
+	st1		{v12.16b-v15.16b}, [x0], #64
 
-	ld1		{v11.16b}, [x20], #16
-	eor		v6.16b, v6.16b, v11.16b
-	st1		{v6.16b}, [x19], #16
-	tbnz		x9, #4, 4f
-
-	ld1		{v12.16b}, [x20], #16
-	eor		v3.16b, v3.16b, v12.16b
-	st1		{v3.16b}, [x19], #16
-	tbnz		x9, #5, 5f
-
-	ld1		{v13.16b}, [x20], #16
-	eor		v7.16b, v7.16b, v13.16b
-	st1		{v7.16b}, [x19], #16
-	tbnz		x9, #6, 6f
+	next_ctr	v0
+	subs		x4, x4, #8
+	b.gt		0b
 
-	ld1		{v14.16b}, [x20], #16
-	eor		v2.16b, v2.16b, v14.16b
-	st1		{v2.16b}, [x19], #16
-	tbnz		x9, #7, 7f
-
-	ld1		{v15.16b}, [x20], #16
-	eor		v5.16b, v5.16b, v15.16b
-	st1		{v5.16b}, [x19], #16
-
-8:	next_ctr	v0
-	st1		{v0.16b}, [x24]
-	cbz		x23, .Lctr_done
-
-	b		99b
-
-.Lctr_done:
-	frame_pop
+	st1		{v0.16b}, [x5]
+	ldp		x29, x30, [sp], #16
 	ret
-
-	/*
-	 * If we are handling the tail of the input (x6 != NULL), return the
-	 * final keystream block back to the caller.
-	 */
-0:	cbz		x25, 8b
-	st1		{v0.16b}, [x25]
-	b		8b
-1:	cbz		x25, 8b
-	st1		{v1.16b}, [x25]
-	b		8b
-2:	cbz		x25, 8b
-	st1		{v4.16b}, [x25]
-	b		8b
-3:	cbz		x25, 8b
-	st1		{v6.16b}, [x25]
-	b		8b
-4:	cbz		x25, 8b
-	st1		{v3.16b}, [x25]
-	b		8b
-5:	cbz		x25, 8b
-	st1		{v7.16b}, [x25]
-	b		8b
-6:	cbz		x25, 8b
-	st1		{v2.16b}, [x25]
-	b		8b
-7:	cbz		x25, 8b
-	st1		{v5.16b}, [x25]
-	b		8b
 SYM_FUNC_END(aesbs_ctr_encrypt)
diff --git a/arch/arm64/crypto/aes-neonbs-glue.c b/arch/arm64/crypto/aes-neonbs-glue.c
index 8df6ad8cb09d..bac4cabef607 100644
--- a/arch/arm64/crypto/aes-neonbs-glue.c
+++ b/arch/arm64/crypto/aes-neonbs-glue.c
@@ -34,7 +34,7 @@ asmlinkage void aesbs_cbc_decrypt(u8 out[], u8 const in[], u8 const rk[],
 				  int rounds, int blocks, u8 iv[]);
 
 asmlinkage void aesbs_ctr_encrypt(u8 out[], u8 const in[], u8 const rk[],
-				  int rounds, int blocks, u8 iv[], u8 final[]);
+				  int rounds, int blocks, u8 iv[]);
 
 asmlinkage void aesbs_xts_encrypt(u8 out[], u8 const in[], u8 const rk[],
 				  int rounds, int blocks, u8 iv[]);
@@ -46,6 +46,8 @@ asmlinkage void neon_aes_ecb_encrypt(u8 out[], u8 const in[], u32 const rk[],
 				     int rounds, int blocks);
 asmlinkage void neon_aes_cbc_encrypt(u8 out[], u8 const in[], u32 const rk[],
 				     int rounds, int blocks, u8 iv[]);
+asmlinkage void neon_aes_ctr_encrypt(u8 out[], u8 const in[], u32 const rk[],
+				     int rounds, int bytes, u8 ctr[]);
 asmlinkage void neon_aes_xts_encrypt(u8 out[], u8 const in[],
 				     u32 const rk1[], int rounds, int bytes,
 				     u32 const rk2[], u8 iv[], int first);
@@ -58,7 +60,7 @@ struct aesbs_ctx {
 	int	rounds;
 } __aligned(AES_BLOCK_SIZE);
 
-struct aesbs_cbc_ctx {
+struct aesbs_cbc_ctr_ctx {
 	struct aesbs_ctx	key;
 	u32			enc[AES_MAX_KEYLENGTH_U32];
 };
@@ -128,10 +130,10 @@ static int ecb_decrypt(struct skcipher_request *req)
 	return __ecb_crypt(req, aesbs_ecb_decrypt);
 }
 
-static int aesbs_cbc_setkey(struct crypto_skcipher *tfm, const u8 *in_key,
+static int aesbs_cbc_ctr_setkey(struct crypto_skcipher *tfm, const u8 *in_key,
 			    unsigned int key_len)
 {
-	struct aesbs_cbc_ctx *ctx = crypto_skcipher_ctx(tfm);
+	struct aesbs_cbc_ctr_ctx *ctx = crypto_skcipher_ctx(tfm);
 	struct crypto_aes_ctx rk;
 	int err;
 
@@ -154,7 +156,7 @@ static int aesbs_cbc_setkey(struct crypto_skcipher *tfm, const u8 *in_key,
 static int cbc_encrypt(struct skcipher_request *req)
 {
 	struct crypto_skcipher *tfm = crypto_skcipher_reqtfm(req);
-	struct aesbs_cbc_ctx *ctx = crypto_skcipher_ctx(tfm);
+	struct aesbs_cbc_ctr_ctx *ctx = crypto_skcipher_ctx(tfm);
 	struct skcipher_walk walk;
 	int err;
 
@@ -177,7 +179,7 @@ static int cbc_encrypt(struct skcipher_request *req)
 static int cbc_decrypt(struct skcipher_request *req)
 {
 	struct crypto_skcipher *tfm = crypto_skcipher_reqtfm(req);
-	struct aesbs_cbc_ctx *ctx = crypto_skcipher_ctx(tfm);
+	struct aesbs_cbc_ctr_ctx *ctx = crypto_skcipher_ctx(tfm);
 	struct skcipher_walk walk;
 	int err;
 
@@ -205,40 +207,32 @@ static int cbc_decrypt(struct skcipher_request *req)
 static int ctr_encrypt(struct skcipher_request *req)
 {
 	struct crypto_skcipher *tfm = crypto_skcipher_reqtfm(req);
-	struct aesbs_ctx *ctx = crypto_skcipher_ctx(tfm);
+	struct aesbs_cbc_ctr_ctx *ctx = crypto_skcipher_ctx(tfm);
 	struct skcipher_walk walk;
-	u8 buf[AES_BLOCK_SIZE];
 	int err;
 
 	err = skcipher_walk_virt(&walk, req, false);
 
 	while (walk.nbytes > 0) {
-		unsigned int blocks = walk.nbytes / AES_BLOCK_SIZE;
-		u8 *final = (walk.total % AES_BLOCK_SIZE) ? buf : NULL;
-
-		if (walk.nbytes < walk.total) {
-			blocks = round_down(blocks,
-					    walk.stride / AES_BLOCK_SIZE);
-			final = NULL;
-		}
+		int blocks = (walk.nbytes / AES_BLOCK_SIZE) & ~7;
+		int nbytes = walk.nbytes % (8 * AES_BLOCK_SIZE);
+		const u8 *src = walk.src.virt.addr;
+		u8 *dst = walk.dst.virt.addr;
 
 		kernel_neon_begin();
-		aesbs_ctr_encrypt(walk.dst.virt.addr, walk.src.virt.addr,
-				  ctx->rk, ctx->rounds, blocks, walk.iv, final);
-		kernel_neon_end();
-
-		if (final) {
-			u8 *dst = walk.dst.virt.addr + blocks * AES_BLOCK_SIZE;
-			u8 *src = walk.src.virt.addr + blocks * AES_BLOCK_SIZE;
-
-			crypto_xor_cpy(dst, src, final,
-				       walk.total % AES_BLOCK_SIZE);
-
-			err = skcipher_walk_done(&walk, 0);
-			break;
+		if (blocks >= 8) {
+			aesbs_ctr_encrypt(dst, src, ctx->key.rk, ctx->key.rounds,
+					  blocks, walk.iv);
+			dst += blocks * AES_BLOCK_SIZE;
+			src += blocks * AES_BLOCK_SIZE;
 		}
-		err = skcipher_walk_done(&walk,
-					 walk.nbytes - blocks * AES_BLOCK_SIZE);
+		if (nbytes && walk.nbytes == walk.total) {
+			neon_aes_ctr_encrypt(dst, src, ctx->enc, ctx->key.rounds,
+					     nbytes, walk.iv);
+			nbytes = 0;
+		}
+		kernel_neon_end();
+		err = skcipher_walk_done(&walk, nbytes);
 	}
 	return err;
 }
@@ -308,23 +302,18 @@ static int __xts_crypt(struct skcipher_request *req, bool encrypt,
 		return err;
 
 	while (walk.nbytes >= AES_BLOCK_SIZE) {
-		unsigned int blocks = walk.nbytes / AES_BLOCK_SIZE;
-
-		if (walk.nbytes < walk.total || walk.nbytes % AES_BLOCK_SIZE)
-			blocks = round_down(blocks,
-					    walk.stride / AES_BLOCK_SIZE);
-
+		int blocks = (walk.nbytes / AES_BLOCK_SIZE) & ~7;
 		out = walk.dst.virt.addr;
 		in = walk.src.virt.addr;
 		nbytes = walk.nbytes;
 
 		kernel_neon_begin();
-		if (likely(blocks > 6)) { /* plain NEON is faster otherwise */
-			if (first)
+		if (blocks >= 8) {
+			if (first == 1)
 				neon_aes_ecb_encrypt(walk.iv, walk.iv,
 						     ctx->twkey,
 						     ctx->key.rounds, 1);
-			first = 0;
+			first = 2;
 
 			fn(out, in, ctx->key.rk, ctx->key.rounds, blocks,
 			   walk.iv);
@@ -333,10 +322,17 @@ static int __xts_crypt(struct skcipher_request *req, bool encrypt,
 			in += blocks * AES_BLOCK_SIZE;
 			nbytes -= blocks * AES_BLOCK_SIZE;
 		}
-
-		if (walk.nbytes == walk.total && nbytes > 0)
-			goto xts_tail;
-
+		if (walk.nbytes == walk.total && nbytes > 0) {
+			if (encrypt)
+				neon_aes_xts_encrypt(out, in, ctx->cts.key_enc,
+						     ctx->key.rounds, nbytes,
+						     ctx->twkey, walk.iv, first);
+			else
+				neon_aes_xts_decrypt(out, in, ctx->cts.key_dec,
+						     ctx->key.rounds, nbytes,
+						     ctx->twkey, walk.iv, first);
+			nbytes = first = 0;
+		}
 		kernel_neon_end();
 		err = skcipher_walk_done(&walk, nbytes);
 	}
@@ -361,13 +357,12 @@ static int __xts_crypt(struct skcipher_request *req, bool encrypt,
 	nbytes = walk.nbytes;
 
 	kernel_neon_begin();
-xts_tail:
 	if (encrypt)
 		neon_aes_xts_encrypt(out, in, ctx->cts.key_enc, ctx->key.rounds,
-				     nbytes, ctx->twkey, walk.iv, first ?: 2);
+				     nbytes, ctx->twkey, walk.iv, first);
 	else
 		neon_aes_xts_decrypt(out, in, ctx->cts.key_dec, ctx->key.rounds,
-				     nbytes, ctx->twkey, walk.iv, first ?: 2);
+				     nbytes, ctx->twkey, walk.iv, first);
 	kernel_neon_end();
 
 	return skcipher_walk_done(&walk, 0);
@@ -402,14 +397,14 @@ static struct skcipher_alg aes_algs[] = { {
 	.base.cra_driver_name	= "cbc-aes-neonbs",
 	.base.cra_priority	= 250,
 	.base.cra_blocksize	= AES_BLOCK_SIZE,
-	.base.cra_ctxsize	= sizeof(struct aesbs_cbc_ctx),
+	.base.cra_ctxsize	= sizeof(struct aesbs_cbc_ctr_ctx),
 	.base.cra_module	= THIS_MODULE,
 
 	.min_keysize		= AES_MIN_KEY_SIZE,
 	.max_keysize		= AES_MAX_KEY_SIZE,
 	.walksize		= 8 * AES_BLOCK_SIZE,
 	.ivsize			= AES_BLOCK_SIZE,
-	.setkey			= aesbs_cbc_setkey,
+	.setkey			= aesbs_cbc_ctr_setkey,
 	.encrypt		= cbc_encrypt,
 	.decrypt		= cbc_decrypt,
 }, {
@@ -417,7 +412,7 @@ static struct skcipher_alg aes_algs[] = { {
 	.base.cra_driver_name	= "ctr-aes-neonbs",
 	.base.cra_priority	= 250,
 	.base.cra_blocksize	= 1,
-	.base.cra_ctxsize	= sizeof(struct aesbs_ctx),
+	.base.cra_ctxsize	= sizeof(struct aesbs_cbc_ctr_ctx),
 	.base.cra_module	= THIS_MODULE,
 
 	.min_keysize		= AES_MIN_KEY_SIZE,
@@ -425,7 +420,7 @@ static struct skcipher_alg aes_algs[] = { {
 	.chunksize		= AES_BLOCK_SIZE,
 	.walksize		= 8 * AES_BLOCK_SIZE,
 	.ivsize			= AES_BLOCK_SIZE,
-	.setkey			= aesbs_setkey,
+	.setkey			= aesbs_cbc_ctr_setkey,
 	.encrypt		= ctr_encrypt,
 	.decrypt		= ctr_encrypt,
 }, {
diff --git a/arch/arm64/crypto/ghash-ce-core.S b/arch/arm64/crypto/ghash-ce-core.S
index 7868330dd54e..ebe5558929b7 100644
--- a/arch/arm64/crypto/ghash-ce-core.S
+++ b/arch/arm64/crypto/ghash-ce-core.S
@@ -6,6 +6,7 @@
  */
 
 #include <linux/linkage.h>
+#include <linux/cfi_types.h>
 #include <asm/assembler.h>
 
 	SHASH		.req	v0
@@ -350,11 +351,11 @@ CPU_LE(	rev64		T1.16b, T1.16b	)
 	 * void pmull_ghash_update(int blocks, u64 dg[], const char *src,
 	 *			   struct ghash_key const *k, const char *head)
 	 */
-SYM_FUNC_START(pmull_ghash_update_p64)
+SYM_TYPED_FUNC_START(pmull_ghash_update_p64)
 	__pmull_ghash	p64
 SYM_FUNC_END(pmull_ghash_update_p64)
 
-SYM_FUNC_START(pmull_ghash_update_p8)
+SYM_TYPED_FUNC_START(pmull_ghash_update_p8)
 	__pmull_ghash	p8
 SYM_FUNC_END(pmull_ghash_update_p8)
 
diff --git a/arch/arm64/crypto/poly1305-glue.c b/arch/arm64/crypto/poly1305-glue.c
index 9c3d86e397bf..1fae18ba11ed 100644
--- a/arch/arm64/crypto/poly1305-glue.c
+++ b/arch/arm64/crypto/poly1305-glue.c
@@ -52,7 +52,7 @@ static void neon_poly1305_blocks(struct poly1305_desc_ctx *dctx, const u8 *src,
 {
 	if (unlikely(!dctx->sset)) {
 		if (!dctx->rset) {
-			poly1305_init_arch(dctx, src);
+			poly1305_init_arm64(&dctx->h, src);
 			src += POLY1305_BLOCK_SIZE;
 			len -= POLY1305_BLOCK_SIZE;
 			dctx->rset = 1;
diff --git a/arch/arm64/crypto/polyval-ce-core.S b/arch/arm64/crypto/polyval-ce-core.S
new file mode 100644
index 000000000000..b5326540d2e3
--- /dev/null
+++ b/arch/arm64/crypto/polyval-ce-core.S
@@ -0,0 +1,361 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Implementation of POLYVAL using ARMv8 Crypto Extensions.
+ *
+ * Copyright 2021 Google LLC
+ */
+/*
+ * This is an efficient implementation of POLYVAL using ARMv8 Crypto Extensions
+ * It works on 8 blocks at a time, by precomputing the first 8 keys powers h^8,
+ * ..., h^1 in the POLYVAL finite field. This precomputation allows us to split
+ * finite field multiplication into two steps.
+ *
+ * In the first step, we consider h^i, m_i as normal polynomials of degree less
+ * than 128. We then compute p(x) = h^8m_0 + ... + h^1m_7 where multiplication
+ * is simply polynomial multiplication.
+ *
+ * In the second step, we compute the reduction of p(x) modulo the finite field
+ * modulus g(x) = x^128 + x^127 + x^126 + x^121 + 1.
+ *
+ * This two step process is equivalent to computing h^8m_0 + ... + h^1m_7 where
+ * multiplication is finite field multiplication. The advantage is that the
+ * two-step process  only requires 1 finite field reduction for every 8
+ * polynomial multiplications. Further parallelism is gained by interleaving the
+ * multiplications and polynomial reductions.
+ */
+
+#include <linux/linkage.h>
+#define STRIDE_BLOCKS 8
+
+KEY_POWERS	.req	x0
+MSG		.req	x1
+BLOCKS_LEFT	.req	x2
+ACCUMULATOR	.req	x3
+KEY_START	.req	x10
+EXTRA_BYTES	.req	x11
+TMP	.req	x13
+
+M0	.req	v0
+M1	.req	v1
+M2	.req	v2
+M3	.req	v3
+M4	.req	v4
+M5	.req	v5
+M6	.req	v6
+M7	.req	v7
+KEY8	.req	v8
+KEY7	.req	v9
+KEY6	.req	v10
+KEY5	.req	v11
+KEY4	.req	v12
+KEY3	.req	v13
+KEY2	.req	v14
+KEY1	.req	v15
+PL	.req	v16
+PH	.req	v17
+TMP_V	.req	v18
+LO	.req	v20
+MI	.req	v21
+HI	.req	v22
+SUM	.req	v23
+GSTAR	.req	v24
+
+	.text
+
+	.arch	armv8-a+crypto
+	.align	4
+
+.Lgstar:
+	.quad	0xc200000000000000, 0xc200000000000000
+
+/*
+ * Computes the product of two 128-bit polynomials in X and Y and XORs the
+ * components of the 256-bit product into LO, MI, HI.
+ *
+ * Given:
+ *  X = [X_1 : X_0]
+ *  Y = [Y_1 : Y_0]
+ *
+ * We compute:
+ *  LO += X_0 * Y_0
+ *  MI += (X_0 + X_1) * (Y_0 + Y_1)
+ *  HI += X_1 * Y_1
+ *
+ * Later, the 256-bit result can be extracted as:
+ *   [HI_1 : HI_0 + HI_1 + MI_1 + LO_1 : LO_1 + HI_0 + MI_0 + LO_0 : LO_0]
+ * This step is done when computing the polynomial reduction for efficiency
+ * reasons.
+ *
+ * Karatsuba multiplication is used instead of Schoolbook multiplication because
+ * it was found to be slightly faster on ARM64 CPUs.
+ *
+ */
+.macro karatsuba1 X Y
+	X .req \X
+	Y .req \Y
+	ext	v25.16b, X.16b, X.16b, #8
+	ext	v26.16b, Y.16b, Y.16b, #8
+	eor	v25.16b, v25.16b, X.16b
+	eor	v26.16b, v26.16b, Y.16b
+	pmull2	v28.1q, X.2d, Y.2d
+	pmull	v29.1q, X.1d, Y.1d
+	pmull	v27.1q, v25.1d, v26.1d
+	eor	HI.16b, HI.16b, v28.16b
+	eor	LO.16b, LO.16b, v29.16b
+	eor	MI.16b, MI.16b, v27.16b
+	.unreq X
+	.unreq Y
+.endm
+
+/*
+ * Same as karatsuba1, except overwrites HI, LO, MI rather than XORing into
+ * them.
+ */
+.macro karatsuba1_store X Y
+	X .req \X
+	Y .req \Y
+	ext	v25.16b, X.16b, X.16b, #8
+	ext	v26.16b, Y.16b, Y.16b, #8
+	eor	v25.16b, v25.16b, X.16b
+	eor	v26.16b, v26.16b, Y.16b
+	pmull2	HI.1q, X.2d, Y.2d
+	pmull	LO.1q, X.1d, Y.1d
+	pmull	MI.1q, v25.1d, v26.1d
+	.unreq X
+	.unreq Y
+.endm
+
+/*
+ * Computes the 256-bit polynomial represented by LO, HI, MI. Stores
+ * the result in PL, PH.
+ * [PH : PL] =
+ *   [HI_1 : HI_1 + HI_0 + MI_1 + LO_1 : HI_0 + MI_0 + LO_1 + LO_0 : LO_0]
+ */
+.macro karatsuba2
+	// v4 = [HI_1 + MI_1 : HI_0 + MI_0]
+	eor	v4.16b, HI.16b, MI.16b
+	// v4 = [HI_1 + MI_1 + LO_1 : HI_0 + MI_0 + LO_0]
+	eor	v4.16b, v4.16b, LO.16b
+	// v5 = [HI_0 : LO_1]
+	ext	v5.16b, LO.16b, HI.16b, #8
+	// v4 = [HI_1 + HI_0 + MI_1 + LO_1 : HI_0 + MI_0 + LO_1 + LO_0]
+	eor	v4.16b, v4.16b, v5.16b
+	// HI = [HI_0 : HI_1]
+	ext	HI.16b, HI.16b, HI.16b, #8
+	// LO = [LO_0 : LO_1]
+	ext	LO.16b, LO.16b, LO.16b, #8
+	// PH = [HI_1 : HI_1 + HI_0 + MI_1 + LO_1]
+	ext	PH.16b, v4.16b, HI.16b, #8
+	// PL = [HI_0 + MI_0 + LO_1 + LO_0 : LO_0]
+	ext	PL.16b, LO.16b, v4.16b, #8
+.endm
+
+/*
+ * Computes the 128-bit reduction of PH : PL. Stores the result in dest.
+ *
+ * This macro computes p(x) mod g(x) where p(x) is in montgomery form and g(x) =
+ * x^128 + x^127 + x^126 + x^121 + 1.
+ *
+ * We have a 256-bit polynomial PH : PL = P_3 : P_2 : P_1 : P_0 that is the
+ * product of two 128-bit polynomials in Montgomery form.  We need to reduce it
+ * mod g(x).  Also, since polynomials in Montgomery form have an "extra" factor
+ * of x^128, this product has two extra factors of x^128.  To get it back into
+ * Montgomery form, we need to remove one of these factors by dividing by x^128.
+ *
+ * To accomplish both of these goals, we add multiples of g(x) that cancel out
+ * the low 128 bits P_1 : P_0, leaving just the high 128 bits. Since the low
+ * bits are zero, the polynomial division by x^128 can be done by right
+ * shifting.
+ *
+ * Since the only nonzero term in the low 64 bits of g(x) is the constant term,
+ * the multiple of g(x) needed to cancel out P_0 is P_0 * g(x).  The CPU can
+ * only do 64x64 bit multiplications, so split P_0 * g(x) into x^128 * P_0 +
+ * x^64 * g*(x) * P_0 + P_0, where g*(x) is bits 64-127 of g(x).  Adding this to
+ * the original polynomial gives P_3 : P_2 + P_0 + T_1 : P_1 + T_0 : 0, where T
+ * = T_1 : T_0 = g*(x) * P_0.  Thus, bits 0-63 got "folded" into bits 64-191.
+ *
+ * Repeating this same process on the next 64 bits "folds" bits 64-127 into bits
+ * 128-255, giving the answer in bits 128-255. This time, we need to cancel P_1
+ * + T_0 in bits 64-127. The multiple of g(x) required is (P_1 + T_0) * g(x) *
+ * x^64. Adding this to our previous computation gives P_3 + P_1 + T_0 + V_1 :
+ * P_2 + P_0 + T_1 + V_0 : 0 : 0, where V = V_1 : V_0 = g*(x) * (P_1 + T_0).
+ *
+ * So our final computation is:
+ *   T = T_1 : T_0 = g*(x) * P_0
+ *   V = V_1 : V_0 = g*(x) * (P_1 + T_0)
+ *   p(x) / x^{128} mod g(x) = P_3 + P_1 + T_0 + V_1 : P_2 + P_0 + T_1 + V_0
+ *
+ * The implementation below saves a XOR instruction by computing P_1 + T_0 : P_0
+ * + T_1 and XORing into dest, rather than separately XORing P_1 : P_0 and T_0 :
+ * T_1 into dest.  This allows us to reuse P_1 + T_0 when computing V.
+ */
+.macro montgomery_reduction dest
+	DEST .req \dest
+	// TMP_V = T_1 : T_0 = P_0 * g*(x)
+	pmull	TMP_V.1q, PL.1d, GSTAR.1d
+	// TMP_V = T_0 : T_1
+	ext	TMP_V.16b, TMP_V.16b, TMP_V.16b, #8
+	// TMP_V = P_1 + T_0 : P_0 + T_1
+	eor	TMP_V.16b, PL.16b, TMP_V.16b
+	// PH = P_3 + P_1 + T_0 : P_2 + P_0 + T_1
+	eor	PH.16b, PH.16b, TMP_V.16b
+	// TMP_V = V_1 : V_0 = (P_1 + T_0) * g*(x)
+	pmull2	TMP_V.1q, TMP_V.2d, GSTAR.2d
+	eor	DEST.16b, PH.16b, TMP_V.16b
+	.unreq DEST
+.endm
+
+/*
+ * Compute Polyval on 8 blocks.
+ *
+ * If reduce is set, also computes the montgomery reduction of the
+ * previous full_stride call and XORs with the first message block.
+ * (m_0 + REDUCE(PL, PH))h^8 + ... + m_7h^1.
+ * I.e., the first multiplication uses m_0 + REDUCE(PL, PH) instead of m_0.
+ *
+ * Sets PL, PH.
+ */
+.macro full_stride reduce
+	eor		LO.16b, LO.16b, LO.16b
+	eor		MI.16b, MI.16b, MI.16b
+	eor		HI.16b, HI.16b, HI.16b
+
+	ld1		{M0.16b, M1.16b, M2.16b, M3.16b}, [MSG], #64
+	ld1		{M4.16b, M5.16b, M6.16b, M7.16b}, [MSG], #64
+
+	karatsuba1 M7 KEY1
+	.if \reduce
+	pmull	TMP_V.1q, PL.1d, GSTAR.1d
+	.endif
+
+	karatsuba1 M6 KEY2
+	.if \reduce
+	ext	TMP_V.16b, TMP_V.16b, TMP_V.16b, #8
+	.endif
+
+	karatsuba1 M5 KEY3
+	.if \reduce
+	eor	TMP_V.16b, PL.16b, TMP_V.16b
+	.endif
+
+	karatsuba1 M4 KEY4
+	.if \reduce
+	eor	PH.16b, PH.16b, TMP_V.16b
+	.endif
+
+	karatsuba1 M3 KEY5
+	.if \reduce
+	pmull2	TMP_V.1q, TMP_V.2d, GSTAR.2d
+	.endif
+
+	karatsuba1 M2 KEY6
+	.if \reduce
+	eor	SUM.16b, PH.16b, TMP_V.16b
+	.endif
+
+	karatsuba1 M1 KEY7
+	eor	M0.16b, M0.16b, SUM.16b
+
+	karatsuba1 M0 KEY8
+	karatsuba2
+.endm
+
+/*
+ * Handle any extra blocks after full_stride loop.
+ */
+.macro partial_stride
+	add	KEY_POWERS, KEY_START, #(STRIDE_BLOCKS << 4)
+	sub	KEY_POWERS, KEY_POWERS, BLOCKS_LEFT, lsl #4
+	ld1	{KEY1.16b}, [KEY_POWERS], #16
+
+	ld1	{TMP_V.16b}, [MSG], #16
+	eor	SUM.16b, SUM.16b, TMP_V.16b
+	karatsuba1_store KEY1 SUM
+	sub	BLOCKS_LEFT, BLOCKS_LEFT, #1
+
+	tst	BLOCKS_LEFT, #4
+	beq	.Lpartial4BlocksDone
+	ld1	{M0.16b, M1.16b,  M2.16b, M3.16b}, [MSG], #64
+	ld1	{KEY8.16b, KEY7.16b, KEY6.16b,	KEY5.16b}, [KEY_POWERS], #64
+	karatsuba1 M0 KEY8
+	karatsuba1 M1 KEY7
+	karatsuba1 M2 KEY6
+	karatsuba1 M3 KEY5
+.Lpartial4BlocksDone:
+	tst	BLOCKS_LEFT, #2
+	beq	.Lpartial2BlocksDone
+	ld1	{M0.16b, M1.16b}, [MSG], #32
+	ld1	{KEY8.16b, KEY7.16b}, [KEY_POWERS], #32
+	karatsuba1 M0 KEY8
+	karatsuba1 M1 KEY7
+.Lpartial2BlocksDone:
+	tst	BLOCKS_LEFT, #1
+	beq	.LpartialDone
+	ld1	{M0.16b}, [MSG], #16
+	ld1	{KEY8.16b}, [KEY_POWERS], #16
+	karatsuba1 M0 KEY8
+.LpartialDone:
+	karatsuba2
+	montgomery_reduction SUM
+.endm
+
+/*
+ * Perform montgomery multiplication in GF(2^128) and store result in op1.
+ *
+ * Computes op1*op2*x^{-128} mod x^128 + x^127 + x^126 + x^121 + 1
+ * If op1, op2 are in montgomery form, this computes the montgomery
+ * form of op1*op2.
+ *
+ * void pmull_polyval_mul(u8 *op1, const u8 *op2);
+ */
+SYM_FUNC_START(pmull_polyval_mul)
+	adr	TMP, .Lgstar
+	ld1	{GSTAR.2d}, [TMP]
+	ld1	{v0.16b}, [x0]
+	ld1	{v1.16b}, [x1]
+	karatsuba1_store v0 v1
+	karatsuba2
+	montgomery_reduction SUM
+	st1	{SUM.16b}, [x0]
+	ret
+SYM_FUNC_END(pmull_polyval_mul)
+
+/*
+ * Perform polynomial evaluation as specified by POLYVAL.  This computes:
+ *	h^n * accumulator + h^n * m_0 + ... + h^1 * m_{n-1}
+ * where n=nblocks, h is the hash key, and m_i are the message blocks.
+ *
+ * x0 - pointer to precomputed key powers h^8 ... h^1
+ * x1 - pointer to message blocks
+ * x2 - number of blocks to hash
+ * x3 - pointer to accumulator
+ *
+ * void pmull_polyval_update(const struct polyval_ctx *ctx, const u8 *in,
+ *			     size_t nblocks, u8 *accumulator);
+ */
+SYM_FUNC_START(pmull_polyval_update)
+	adr	TMP, .Lgstar
+	mov	KEY_START, KEY_POWERS
+	ld1	{GSTAR.2d}, [TMP]
+	ld1	{SUM.16b}, [ACCUMULATOR]
+	subs	BLOCKS_LEFT, BLOCKS_LEFT, #STRIDE_BLOCKS
+	blt .LstrideLoopExit
+	ld1	{KEY8.16b, KEY7.16b, KEY6.16b, KEY5.16b}, [KEY_POWERS], #64
+	ld1	{KEY4.16b, KEY3.16b, KEY2.16b, KEY1.16b}, [KEY_POWERS], #64
+	full_stride 0
+	subs	BLOCKS_LEFT, BLOCKS_LEFT, #STRIDE_BLOCKS
+	blt .LstrideLoopExitReduce
+.LstrideLoop:
+	full_stride 1
+	subs	BLOCKS_LEFT, BLOCKS_LEFT, #STRIDE_BLOCKS
+	bge	.LstrideLoop
+.LstrideLoopExitReduce:
+	montgomery_reduction SUM
+.LstrideLoopExit:
+	adds	BLOCKS_LEFT, BLOCKS_LEFT, #STRIDE_BLOCKS
+	beq	.LskipPartial
+	partial_stride
+.LskipPartial:
+	st1	{SUM.16b}, [ACCUMULATOR]
+	ret
+SYM_FUNC_END(pmull_polyval_update)
diff --git a/arch/arm64/crypto/polyval-ce-glue.c b/arch/arm64/crypto/polyval-ce-glue.c
new file mode 100644
index 000000000000..0a3b5718df85
--- /dev/null
+++ b/arch/arm64/crypto/polyval-ce-glue.c
@@ -0,0 +1,191 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Glue code for POLYVAL using ARMv8 Crypto Extensions
+ *
+ * Copyright (c) 2007 Nokia Siemens Networks - Mikko Herranen <mh1@iki.fi>
+ * Copyright (c) 2009 Intel Corp.
+ *   Author: Huang Ying <ying.huang@intel.com>
+ * Copyright 2021 Google LLC
+ */
+
+/*
+ * Glue code based on ghash-clmulni-intel_glue.c.
+ *
+ * This implementation of POLYVAL uses montgomery multiplication accelerated by
+ * ARMv8 Crypto Extensions instructions to implement the finite field operations.
+ */
+
+#include <crypto/algapi.h>
+#include <crypto/internal/hash.h>
+#include <crypto/internal/simd.h>
+#include <crypto/polyval.h>
+#include <linux/crypto.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/cpufeature.h>
+#include <asm/neon.h>
+#include <asm/simd.h>
+
+#define NUM_KEY_POWERS	8
+
+struct polyval_tfm_ctx {
+	/*
+	 * These powers must be in the order h^8, ..., h^1.
+	 */
+	u8 key_powers[NUM_KEY_POWERS][POLYVAL_BLOCK_SIZE];
+};
+
+struct polyval_desc_ctx {
+	u8 buffer[POLYVAL_BLOCK_SIZE];
+	u32 bytes;
+};
+
+asmlinkage void pmull_polyval_update(const struct polyval_tfm_ctx *keys,
+	const u8 *in, size_t nblocks, u8 *accumulator);
+asmlinkage void pmull_polyval_mul(u8 *op1, const u8 *op2);
+
+static void internal_polyval_update(const struct polyval_tfm_ctx *keys,
+	const u8 *in, size_t nblocks, u8 *accumulator)
+{
+	if (likely(crypto_simd_usable())) {
+		kernel_neon_begin();
+		pmull_polyval_update(keys, in, nblocks, accumulator);
+		kernel_neon_end();
+	} else {
+		polyval_update_non4k(keys->key_powers[NUM_KEY_POWERS-1], in,
+			nblocks, accumulator);
+	}
+}
+
+static void internal_polyval_mul(u8 *op1, const u8 *op2)
+{
+	if (likely(crypto_simd_usable())) {
+		kernel_neon_begin();
+		pmull_polyval_mul(op1, op2);
+		kernel_neon_end();
+	} else {
+		polyval_mul_non4k(op1, op2);
+	}
+}
+
+static int polyval_arm64_setkey(struct crypto_shash *tfm,
+			const u8 *key, unsigned int keylen)
+{
+	struct polyval_tfm_ctx *tctx = crypto_shash_ctx(tfm);
+	int i;
+
+	if (keylen != POLYVAL_BLOCK_SIZE)
+		return -EINVAL;
+
+	memcpy(tctx->key_powers[NUM_KEY_POWERS-1], key, POLYVAL_BLOCK_SIZE);
+
+	for (i = NUM_KEY_POWERS-2; i >= 0; i--) {
+		memcpy(tctx->key_powers[i], key, POLYVAL_BLOCK_SIZE);
+		internal_polyval_mul(tctx->key_powers[i],
+				     tctx->key_powers[i+1]);
+	}
+
+	return 0;
+}
+
+static int polyval_arm64_init(struct shash_desc *desc)
+{
+	struct polyval_desc_ctx *dctx = shash_desc_ctx(desc);
+
+	memset(dctx, 0, sizeof(*dctx));
+
+	return 0;
+}
+
+static int polyval_arm64_update(struct shash_desc *desc,
+			 const u8 *src, unsigned int srclen)
+{
+	struct polyval_desc_ctx *dctx = shash_desc_ctx(desc);
+	const struct polyval_tfm_ctx *tctx = crypto_shash_ctx(desc->tfm);
+	u8 *pos;
+	unsigned int nblocks;
+	unsigned int n;
+
+	if (dctx->bytes) {
+		n = min(srclen, dctx->bytes);
+		pos = dctx->buffer + POLYVAL_BLOCK_SIZE - dctx->bytes;
+
+		dctx->bytes -= n;
+		srclen -= n;
+
+		while (n--)
+			*pos++ ^= *src++;
+
+		if (!dctx->bytes)
+			internal_polyval_mul(dctx->buffer,
+					    tctx->key_powers[NUM_KEY_POWERS-1]);
+	}
+
+	while (srclen >= POLYVAL_BLOCK_SIZE) {
+		/* allow rescheduling every 4K bytes */
+		nblocks = min(srclen, 4096U) / POLYVAL_BLOCK_SIZE;
+		internal_polyval_update(tctx, src, nblocks, dctx->buffer);
+		srclen -= nblocks * POLYVAL_BLOCK_SIZE;
+		src += nblocks * POLYVAL_BLOCK_SIZE;
+	}
+
+	if (srclen) {
+		dctx->bytes = POLYVAL_BLOCK_SIZE - srclen;
+		pos = dctx->buffer;
+		while (srclen--)
+			*pos++ ^= *src++;
+	}
+
+	return 0;
+}
+
+static int polyval_arm64_final(struct shash_desc *desc, u8 *dst)
+{
+	struct polyval_desc_ctx *dctx = shash_desc_ctx(desc);
+	const struct polyval_tfm_ctx *tctx = crypto_shash_ctx(desc->tfm);
+
+	if (dctx->bytes) {
+		internal_polyval_mul(dctx->buffer,
+				     tctx->key_powers[NUM_KEY_POWERS-1]);
+	}
+
+	memcpy(dst, dctx->buffer, POLYVAL_BLOCK_SIZE);
+
+	return 0;
+}
+
+static struct shash_alg polyval_alg = {
+	.digestsize	= POLYVAL_DIGEST_SIZE,
+	.init		= polyval_arm64_init,
+	.update		= polyval_arm64_update,
+	.final		= polyval_arm64_final,
+	.setkey		= polyval_arm64_setkey,
+	.descsize	= sizeof(struct polyval_desc_ctx),
+	.base		= {
+		.cra_name		= "polyval",
+		.cra_driver_name	= "polyval-ce",
+		.cra_priority		= 200,
+		.cra_blocksize		= POLYVAL_BLOCK_SIZE,
+		.cra_ctxsize		= sizeof(struct polyval_tfm_ctx),
+		.cra_module		= THIS_MODULE,
+	},
+};
+
+static int __init polyval_ce_mod_init(void)
+{
+	return crypto_register_shash(&polyval_alg);
+}
+
+static void __exit polyval_ce_mod_exit(void)
+{
+	crypto_unregister_shash(&polyval_alg);
+}
+
+module_cpu_feature_match(PMULL, polyval_ce_mod_init)
+module_exit(polyval_ce_mod_exit);
+
+MODULE_LICENSE("GPL");
+MODULE_DESCRIPTION("POLYVAL hash function accelerated by ARMv8 Crypto Extensions");
+MODULE_ALIAS_CRYPTO("polyval");
+MODULE_ALIAS_CRYPTO("polyval-ce");
diff --git a/arch/arm64/crypto/sha3-ce-glue.c b/arch/arm64/crypto/sha3-ce-glue.c
index 8c65cecf560a..250e1377c481 100644
--- a/arch/arm64/crypto/sha3-ce-glue.c
+++ b/arch/arm64/crypto/sha3-ce-glue.c
@@ -1,4 +1,4 @@
-/* SPDX-License-Identifier: GPL-2.0 */
+// SPDX-License-Identifier: GPL-2.0
 /*
  * sha3-ce-glue.c - core SHA-3 transform using v8.2 Crypto Extensions
  *
diff --git a/arch/arm64/crypto/sha512-armv8.pl b/arch/arm64/crypto/sha512-armv8.pl
index 2d8655d5b1af..35ec9ae99fe1 100644
--- a/arch/arm64/crypto/sha512-armv8.pl
+++ b/arch/arm64/crypto/sha512-armv8.pl
@@ -43,7 +43,7 @@
 #	on Cortex-A53 (or by 4 cycles per round).
 # (***)	Super-impressive coefficients over gcc-generated code are
 #	indication of some compiler "pathology", most notably code
-#	generated with -mgeneral-regs-only is significanty faster
+#	generated with -mgeneral-regs-only is significantly faster
 #	and the gap is only 40-90%.
 #
 # October 2016.
diff --git a/arch/arm64/crypto/sha512-ce-glue.c b/arch/arm64/crypto/sha512-ce-glue.c
index e62a094a9d52..94cb7580deb7 100644
--- a/arch/arm64/crypto/sha512-ce-glue.c
+++ b/arch/arm64/crypto/sha512-ce-glue.c
@@ -1,4 +1,4 @@
-/* SPDX-License-Identifier: GPL-2.0 */
+// SPDX-License-Identifier: GPL-2.0
 /*
  * sha512-ce-glue.c - SHA-384/SHA-512 using ARMv8 Crypto Extensions
  *
diff --git a/arch/arm64/crypto/sm3-ce-core.S b/arch/arm64/crypto/sm3-ce-core.S
index ef97d3187cb7..ca70cfacd0d0 100644
--- a/arch/arm64/crypto/sm3-ce-core.S
+++ b/arch/arm64/crypto/sm3-ce-core.S
@@ -6,6 +6,7 @@
  */
 
 #include <linux/linkage.h>
+#include <linux/cfi_types.h>
 #include <asm/assembler.h>
 
 	.irp		b, 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12
@@ -73,7 +74,7 @@
 	 *                       int blocks)
 	 */
 	.text
-SYM_FUNC_START(sm3_ce_transform)
+SYM_TYPED_FUNC_START(sm3_ce_transform)
 	/* load state */
 	ld1		{v8.4s-v9.4s}, [x0]
 	rev64		v8.4s, v8.4s
diff --git a/arch/arm64/crypto/sm3-ce-glue.c b/arch/arm64/crypto/sm3-ce-glue.c
index d71faca322f2..ee98954ae8ca 100644
--- a/arch/arm64/crypto/sm3-ce-glue.c
+++ b/arch/arm64/crypto/sm3-ce-glue.c
@@ -26,8 +26,10 @@ asmlinkage void sm3_ce_transform(struct sm3_state *sst, u8 const *src,
 static int sm3_ce_update(struct shash_desc *desc, const u8 *data,
 			 unsigned int len)
 {
-	if (!crypto_simd_usable())
-		return crypto_sm3_update(desc, data, len);
+	if (!crypto_simd_usable()) {
+		sm3_update(shash_desc_ctx(desc), data, len);
+		return 0;
+	}
 
 	kernel_neon_begin();
 	sm3_base_do_update(desc, data, len, sm3_ce_transform);
@@ -38,8 +40,10 @@ static int sm3_ce_update(struct shash_desc *desc, const u8 *data,
 
 static int sm3_ce_final(struct shash_desc *desc, u8 *out)
 {
-	if (!crypto_simd_usable())
-		return crypto_sm3_finup(desc, NULL, 0, out);
+	if (!crypto_simd_usable()) {
+		sm3_final(shash_desc_ctx(desc), out);
+		return 0;
+	}
 
 	kernel_neon_begin();
 	sm3_base_do_finalize(desc, sm3_ce_transform);
@@ -51,14 +55,22 @@ static int sm3_ce_final(struct shash_desc *desc, u8 *out)
 static int sm3_ce_finup(struct shash_desc *desc, const u8 *data,
 			unsigned int len, u8 *out)
 {
-	if (!crypto_simd_usable())
-		return crypto_sm3_finup(desc, data, len, out);
+	if (!crypto_simd_usable()) {
+		struct sm3_state *sctx = shash_desc_ctx(desc);
+
+		if (len)
+			sm3_update(sctx, data, len);
+		sm3_final(sctx, out);
+		return 0;
+	}
 
 	kernel_neon_begin();
-	sm3_base_do_update(desc, data, len, sm3_ce_transform);
+	if (len)
+		sm3_base_do_update(desc, data, len, sm3_ce_transform);
+	sm3_base_do_finalize(desc, sm3_ce_transform);
 	kernel_neon_end();
 
-	return sm3_ce_final(desc, out);
+	return sm3_base_finish(desc, out);
 }
 
 static struct shash_alg sm3_alg = {
diff --git a/arch/arm64/crypto/sm4-ce-cipher-core.S b/arch/arm64/crypto/sm4-ce-cipher-core.S
new file mode 100644
index 000000000000..4ac6cfbc5797
--- /dev/null
+++ b/arch/arm64/crypto/sm4-ce-cipher-core.S
@@ -0,0 +1,36 @@
+// SPDX-License-Identifier: GPL-2.0
+
+#include <linux/linkage.h>
+#include <asm/assembler.h>
+
+	.irp		b, 0, 1, 2, 3, 4, 5, 6, 7, 8
+	.set		.Lv\b\().4s, \b
+	.endr
+
+	.macro		sm4e, rd, rn
+	.inst		0xcec08400 | .L\rd | (.L\rn << 5)
+	.endm
+
+	/*
+	 * void sm4_ce_do_crypt(const u32 *rk, u32 *out, const u32 *in);
+	 */
+	.text
+SYM_FUNC_START(sm4_ce_do_crypt)
+	ld1		{v8.4s}, [x2]
+	ld1		{v0.4s-v3.4s}, [x0], #64
+CPU_LE(	rev32		v8.16b, v8.16b		)
+	ld1		{v4.4s-v7.4s}, [x0]
+	sm4e		v8.4s, v0.4s
+	sm4e		v8.4s, v1.4s
+	sm4e		v8.4s, v2.4s
+	sm4e		v8.4s, v3.4s
+	sm4e		v8.4s, v4.4s
+	sm4e		v8.4s, v5.4s
+	sm4e		v8.4s, v6.4s
+	sm4e		v8.4s, v7.4s
+	rev64		v8.4s, v8.4s
+	ext		v8.16b, v8.16b, v8.16b, #8
+CPU_LE(	rev32		v8.16b, v8.16b		)
+	st1		{v8.4s}, [x1]
+	ret
+SYM_FUNC_END(sm4_ce_do_crypt)
diff --git a/arch/arm64/crypto/sm4-ce-cipher-glue.c b/arch/arm64/crypto/sm4-ce-cipher-glue.c
new file mode 100644
index 000000000000..76a34ef4abbb
--- /dev/null
+++ b/arch/arm64/crypto/sm4-ce-cipher-glue.c
@@ -0,0 +1,82 @@
+// SPDX-License-Identifier: GPL-2.0
+
+#include <asm/neon.h>
+#include <asm/simd.h>
+#include <crypto/sm4.h>
+#include <crypto/internal/simd.h>
+#include <linux/module.h>
+#include <linux/cpufeature.h>
+#include <linux/crypto.h>
+#include <linux/types.h>
+
+MODULE_ALIAS_CRYPTO("sm4");
+MODULE_ALIAS_CRYPTO("sm4-ce");
+MODULE_DESCRIPTION("SM4 symmetric cipher using ARMv8 Crypto Extensions");
+MODULE_AUTHOR("Ard Biesheuvel <ard.biesheuvel@linaro.org>");
+MODULE_LICENSE("GPL v2");
+
+asmlinkage void sm4_ce_do_crypt(const u32 *rk, void *out, const void *in);
+
+static int sm4_ce_setkey(struct crypto_tfm *tfm, const u8 *key,
+		       unsigned int key_len)
+{
+	struct sm4_ctx *ctx = crypto_tfm_ctx(tfm);
+
+	return sm4_expandkey(ctx, key, key_len);
+}
+
+static void sm4_ce_encrypt(struct crypto_tfm *tfm, u8 *out, const u8 *in)
+{
+	const struct sm4_ctx *ctx = crypto_tfm_ctx(tfm);
+
+	if (!crypto_simd_usable()) {
+		sm4_crypt_block(ctx->rkey_enc, out, in);
+	} else {
+		kernel_neon_begin();
+		sm4_ce_do_crypt(ctx->rkey_enc, out, in);
+		kernel_neon_end();
+	}
+}
+
+static void sm4_ce_decrypt(struct crypto_tfm *tfm, u8 *out, const u8 *in)
+{
+	const struct sm4_ctx *ctx = crypto_tfm_ctx(tfm);
+
+	if (!crypto_simd_usable()) {
+		sm4_crypt_block(ctx->rkey_dec, out, in);
+	} else {
+		kernel_neon_begin();
+		sm4_ce_do_crypt(ctx->rkey_dec, out, in);
+		kernel_neon_end();
+	}
+}
+
+static struct crypto_alg sm4_ce_alg = {
+	.cra_name			= "sm4",
+	.cra_driver_name		= "sm4-ce",
+	.cra_priority			= 300,
+	.cra_flags			= CRYPTO_ALG_TYPE_CIPHER,
+	.cra_blocksize			= SM4_BLOCK_SIZE,
+	.cra_ctxsize			= sizeof(struct sm4_ctx),
+	.cra_module			= THIS_MODULE,
+	.cra_u.cipher = {
+		.cia_min_keysize	= SM4_KEY_SIZE,
+		.cia_max_keysize	= SM4_KEY_SIZE,
+		.cia_setkey		= sm4_ce_setkey,
+		.cia_encrypt		= sm4_ce_encrypt,
+		.cia_decrypt		= sm4_ce_decrypt
+	}
+};
+
+static int __init sm4_ce_mod_init(void)
+{
+	return crypto_register_alg(&sm4_ce_alg);
+}
+
+static void __exit sm4_ce_mod_fini(void)
+{
+	crypto_unregister_alg(&sm4_ce_alg);
+}
+
+module_cpu_feature_match(SM4, sm4_ce_mod_init);
+module_exit(sm4_ce_mod_fini);
diff --git a/arch/arm64/crypto/sm4-ce-core.S b/arch/arm64/crypto/sm4-ce-core.S
index 4ac6cfbc5797..934e0f093279 100644
--- a/arch/arm64/crypto/sm4-ce-core.S
+++ b/arch/arm64/crypto/sm4-ce-core.S
@@ -1,36 +1,660 @@
-// SPDX-License-Identifier: GPL-2.0
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * SM4 Cipher Algorithm for ARMv8 with Crypto Extensions
+ * as specified in
+ * https://tools.ietf.org/id/draft-ribose-cfrg-sm4-10.html
+ *
+ * Copyright (C) 2022, Alibaba Group.
+ * Copyright (C) 2022 Tianjia Zhang <tianjia.zhang@linux.alibaba.com>
+ */
 
 #include <linux/linkage.h>
 #include <asm/assembler.h>
 
-	.irp		b, 0, 1, 2, 3, 4, 5, 6, 7, 8
-	.set		.Lv\b\().4s, \b
-	.endr
-
-	.macro		sm4e, rd, rn
-	.inst		0xcec08400 | .L\rd | (.L\rn << 5)
-	.endm
-
-	/*
-	 * void sm4_ce_do_crypt(const u32 *rk, u32 *out, const u32 *in);
-	 */
-	.text
-SYM_FUNC_START(sm4_ce_do_crypt)
-	ld1		{v8.4s}, [x2]
-	ld1		{v0.4s-v3.4s}, [x0], #64
-CPU_LE(	rev32		v8.16b, v8.16b		)
-	ld1		{v4.4s-v7.4s}, [x0]
-	sm4e		v8.4s, v0.4s
-	sm4e		v8.4s, v1.4s
-	sm4e		v8.4s, v2.4s
-	sm4e		v8.4s, v3.4s
-	sm4e		v8.4s, v4.4s
-	sm4e		v8.4s, v5.4s
-	sm4e		v8.4s, v6.4s
-	sm4e		v8.4s, v7.4s
-	rev64		v8.4s, v8.4s
-	ext		v8.16b, v8.16b, v8.16b, #8
-CPU_LE(	rev32		v8.16b, v8.16b		)
-	st1		{v8.4s}, [x1]
-	ret
-SYM_FUNC_END(sm4_ce_do_crypt)
+.arch	armv8-a+crypto
+
+.irp b, 0, 1, 2, 3, 4, 5, 6, 7, 16, 20, 24, 25, 26, 27, 28, 29, 30, 31
+	.set .Lv\b\().4s, \b
+.endr
+
+.macro sm4e, vd, vn
+	.inst 0xcec08400 | (.L\vn << 5) | .L\vd
+.endm
+
+.macro sm4ekey, vd, vn, vm
+	.inst 0xce60c800 | (.L\vm << 16) | (.L\vn << 5) | .L\vd
+.endm
+
+/* Register macros */
+
+#define RTMP0	v16
+#define RTMP1	v17
+#define RTMP2	v18
+#define RTMP3	v19
+
+#define RIV	v20
+
+/* Helper macros. */
+
+#define PREPARE                                       \
+	ld1		{v24.16b-v27.16b}, [x0], #64; \
+	ld1		{v28.16b-v31.16b}, [x0];
+
+#define SM4_CRYPT_BLK(b0)                           \
+	rev32		b0.16b, b0.16b;             \
+	sm4e		b0.4s, v24.4s;              \
+	sm4e		b0.4s, v25.4s;              \
+	sm4e		b0.4s, v26.4s;              \
+	sm4e		b0.4s, v27.4s;              \
+	sm4e		b0.4s, v28.4s;              \
+	sm4e		b0.4s, v29.4s;              \
+	sm4e		b0.4s, v30.4s;              \
+	sm4e		b0.4s, v31.4s;              \
+	rev64		b0.4s, b0.4s;               \
+	ext		b0.16b, b0.16b, b0.16b, #8; \
+	rev32		b0.16b, b0.16b;
+
+#define SM4_CRYPT_BLK4(b0, b1, b2, b3)              \
+	rev32		b0.16b, b0.16b;             \
+	rev32		b1.16b, b1.16b;             \
+	rev32		b2.16b, b2.16b;             \
+	rev32		b3.16b, b3.16b;             \
+	sm4e		b0.4s, v24.4s;              \
+	sm4e		b1.4s, v24.4s;              \
+	sm4e		b2.4s, v24.4s;              \
+	sm4e		b3.4s, v24.4s;              \
+	sm4e		b0.4s, v25.4s;              \
+	sm4e		b1.4s, v25.4s;              \
+	sm4e		b2.4s, v25.4s;              \
+	sm4e		b3.4s, v25.4s;              \
+	sm4e		b0.4s, v26.4s;              \
+	sm4e		b1.4s, v26.4s;              \
+	sm4e		b2.4s, v26.4s;              \
+	sm4e		b3.4s, v26.4s;              \
+	sm4e		b0.4s, v27.4s;              \
+	sm4e		b1.4s, v27.4s;              \
+	sm4e		b2.4s, v27.4s;              \
+	sm4e		b3.4s, v27.4s;              \
+	sm4e		b0.4s, v28.4s;              \
+	sm4e		b1.4s, v28.4s;              \
+	sm4e		b2.4s, v28.4s;              \
+	sm4e		b3.4s, v28.4s;              \
+	sm4e		b0.4s, v29.4s;              \
+	sm4e		b1.4s, v29.4s;              \
+	sm4e		b2.4s, v29.4s;              \
+	sm4e		b3.4s, v29.4s;              \
+	sm4e		b0.4s, v30.4s;              \
+	sm4e		b1.4s, v30.4s;              \
+	sm4e		b2.4s, v30.4s;              \
+	sm4e		b3.4s, v30.4s;              \
+	sm4e		b0.4s, v31.4s;              \
+	sm4e		b1.4s, v31.4s;              \
+	sm4e		b2.4s, v31.4s;              \
+	sm4e		b3.4s, v31.4s;              \
+	rev64		b0.4s, b0.4s;               \
+	rev64		b1.4s, b1.4s;               \
+	rev64		b2.4s, b2.4s;               \
+	rev64		b3.4s, b3.4s;               \
+	ext		b0.16b, b0.16b, b0.16b, #8; \
+	ext		b1.16b, b1.16b, b1.16b, #8; \
+	ext		b2.16b, b2.16b, b2.16b, #8; \
+	ext		b3.16b, b3.16b, b3.16b, #8; \
+	rev32		b0.16b, b0.16b;             \
+	rev32		b1.16b, b1.16b;             \
+	rev32		b2.16b, b2.16b;             \
+	rev32		b3.16b, b3.16b;
+
+#define SM4_CRYPT_BLK8(b0, b1, b2, b3, b4, b5, b6, b7) \
+	rev32		b0.16b, b0.16b;             \
+	rev32		b1.16b, b1.16b;             \
+	rev32		b2.16b, b2.16b;             \
+	rev32		b3.16b, b3.16b;             \
+	rev32		b4.16b, b4.16b;             \
+	rev32		b5.16b, b5.16b;             \
+	rev32		b6.16b, b6.16b;             \
+	rev32		b7.16b, b7.16b;             \
+	sm4e		b0.4s, v24.4s;              \
+	sm4e		b1.4s, v24.4s;              \
+	sm4e		b2.4s, v24.4s;              \
+	sm4e		b3.4s, v24.4s;              \
+	sm4e		b4.4s, v24.4s;              \
+	sm4e		b5.4s, v24.4s;              \
+	sm4e		b6.4s, v24.4s;              \
+	sm4e		b7.4s, v24.4s;              \
+	sm4e		b0.4s, v25.4s;              \
+	sm4e		b1.4s, v25.4s;              \
+	sm4e		b2.4s, v25.4s;              \
+	sm4e		b3.4s, v25.4s;              \
+	sm4e		b4.4s, v25.4s;              \
+	sm4e		b5.4s, v25.4s;              \
+	sm4e		b6.4s, v25.4s;              \
+	sm4e		b7.4s, v25.4s;              \
+	sm4e		b0.4s, v26.4s;              \
+	sm4e		b1.4s, v26.4s;              \
+	sm4e		b2.4s, v26.4s;              \
+	sm4e		b3.4s, v26.4s;              \
+	sm4e		b4.4s, v26.4s;              \
+	sm4e		b5.4s, v26.4s;              \
+	sm4e		b6.4s, v26.4s;              \
+	sm4e		b7.4s, v26.4s;              \
+	sm4e		b0.4s, v27.4s;              \
+	sm4e		b1.4s, v27.4s;              \
+	sm4e		b2.4s, v27.4s;              \
+	sm4e		b3.4s, v27.4s;              \
+	sm4e		b4.4s, v27.4s;              \
+	sm4e		b5.4s, v27.4s;              \
+	sm4e		b6.4s, v27.4s;              \
+	sm4e		b7.4s, v27.4s;              \
+	sm4e		b0.4s, v28.4s;              \
+	sm4e		b1.4s, v28.4s;              \
+	sm4e		b2.4s, v28.4s;              \
+	sm4e		b3.4s, v28.4s;              \
+	sm4e		b4.4s, v28.4s;              \
+	sm4e		b5.4s, v28.4s;              \
+	sm4e		b6.4s, v28.4s;              \
+	sm4e		b7.4s, v28.4s;              \
+	sm4e		b0.4s, v29.4s;              \
+	sm4e		b1.4s, v29.4s;              \
+	sm4e		b2.4s, v29.4s;              \
+	sm4e		b3.4s, v29.4s;              \
+	sm4e		b4.4s, v29.4s;              \
+	sm4e		b5.4s, v29.4s;              \
+	sm4e		b6.4s, v29.4s;              \
+	sm4e		b7.4s, v29.4s;              \
+	sm4e		b0.4s, v30.4s;              \
+	sm4e		b1.4s, v30.4s;              \
+	sm4e		b2.4s, v30.4s;              \
+	sm4e		b3.4s, v30.4s;              \
+	sm4e		b4.4s, v30.4s;              \
+	sm4e		b5.4s, v30.4s;              \
+	sm4e		b6.4s, v30.4s;              \
+	sm4e		b7.4s, v30.4s;              \
+	sm4e		b0.4s, v31.4s;              \
+	sm4e		b1.4s, v31.4s;              \
+	sm4e		b2.4s, v31.4s;              \
+	sm4e		b3.4s, v31.4s;              \
+	sm4e		b4.4s, v31.4s;              \
+	sm4e		b5.4s, v31.4s;              \
+	sm4e		b6.4s, v31.4s;              \
+	sm4e		b7.4s, v31.4s;              \
+	rev64		b0.4s, b0.4s;               \
+	rev64		b1.4s, b1.4s;               \
+	rev64		b2.4s, b2.4s;               \
+	rev64		b3.4s, b3.4s;               \
+	rev64		b4.4s, b4.4s;               \
+	rev64		b5.4s, b5.4s;               \
+	rev64		b6.4s, b6.4s;               \
+	rev64		b7.4s, b7.4s;               \
+	ext		b0.16b, b0.16b, b0.16b, #8; \
+	ext		b1.16b, b1.16b, b1.16b, #8; \
+	ext		b2.16b, b2.16b, b2.16b, #8; \
+	ext		b3.16b, b3.16b, b3.16b, #8; \
+	ext		b4.16b, b4.16b, b4.16b, #8; \
+	ext		b5.16b, b5.16b, b5.16b, #8; \
+	ext		b6.16b, b6.16b, b6.16b, #8; \
+	ext		b7.16b, b7.16b, b7.16b, #8; \
+	rev32		b0.16b, b0.16b;             \
+	rev32		b1.16b, b1.16b;             \
+	rev32		b2.16b, b2.16b;             \
+	rev32		b3.16b, b3.16b;             \
+	rev32		b4.16b, b4.16b;             \
+	rev32		b5.16b, b5.16b;             \
+	rev32		b6.16b, b6.16b;             \
+	rev32		b7.16b, b7.16b;
+
+
+.align 3
+SYM_FUNC_START(sm4_ce_expand_key)
+	/* input:
+	 *   x0: 128-bit key
+	 *   x1: rkey_enc
+	 *   x2: rkey_dec
+	 *   x3: fk array
+	 *   x4: ck array
+	 */
+	ld1		{v0.16b}, [x0];
+	rev32		v0.16b, v0.16b;
+	ld1		{v1.16b}, [x3];
+	/* load ck */
+	ld1		{v24.16b-v27.16b}, [x4], #64;
+	ld1		{v28.16b-v31.16b}, [x4];
+
+	/* input ^ fk */
+	eor		v0.16b, v0.16b, v1.16b;
+
+	sm4ekey		v0.4s, v0.4s, v24.4s;
+	sm4ekey		v1.4s, v0.4s, v25.4s;
+	sm4ekey		v2.4s, v1.4s, v26.4s;
+	sm4ekey		v3.4s, v2.4s, v27.4s;
+	sm4ekey		v4.4s, v3.4s, v28.4s;
+	sm4ekey		v5.4s, v4.4s, v29.4s;
+	sm4ekey		v6.4s, v5.4s, v30.4s;
+	sm4ekey		v7.4s, v6.4s, v31.4s;
+
+	st1		{v0.16b-v3.16b}, [x1], #64;
+	st1		{v4.16b-v7.16b}, [x1];
+	rev64		v7.4s, v7.4s;
+	rev64		v6.4s, v6.4s;
+	rev64		v5.4s, v5.4s;
+	rev64		v4.4s, v4.4s;
+	rev64		v3.4s, v3.4s;
+	rev64		v2.4s, v2.4s;
+	rev64		v1.4s, v1.4s;
+	rev64		v0.4s, v0.4s;
+	ext		v7.16b, v7.16b, v7.16b, #8;
+	ext		v6.16b, v6.16b, v6.16b, #8;
+	ext		v5.16b, v5.16b, v5.16b, #8;
+	ext		v4.16b, v4.16b, v4.16b, #8;
+	ext		v3.16b, v3.16b, v3.16b, #8;
+	ext		v2.16b, v2.16b, v2.16b, #8;
+	ext		v1.16b, v1.16b, v1.16b, #8;
+	ext		v0.16b, v0.16b, v0.16b, #8;
+	st1		{v7.16b}, [x2], #16;
+	st1		{v6.16b}, [x2], #16;
+	st1		{v5.16b}, [x2], #16;
+	st1		{v4.16b}, [x2], #16;
+	st1		{v3.16b}, [x2], #16;
+	st1		{v2.16b}, [x2], #16;
+	st1		{v1.16b}, [x2], #16;
+	st1		{v0.16b}, [x2];
+
+	ret;
+SYM_FUNC_END(sm4_ce_expand_key)
+
+.align 3
+SYM_FUNC_START(sm4_ce_crypt_block)
+	/* input:
+	 *   x0: round key array, CTX
+	 *   x1: dst
+	 *   x2: src
+	 */
+	PREPARE;
+
+	ld1		{v0.16b}, [x2];
+	SM4_CRYPT_BLK(v0);
+	st1		{v0.16b}, [x1];
+
+	ret;
+SYM_FUNC_END(sm4_ce_crypt_block)
+
+.align 3
+SYM_FUNC_START(sm4_ce_crypt)
+	/* input:
+	 *   x0: round key array, CTX
+	 *   x1: dst
+	 *   x2: src
+	 *   w3: nblocks
+	 */
+	PREPARE;
+
+.Lcrypt_loop_blk:
+	sub		w3, w3, #8;
+	tbnz		w3, #31, .Lcrypt_tail8;
+
+	ld1		{v0.16b-v3.16b}, [x2], #64;
+	ld1		{v4.16b-v7.16b}, [x2], #64;
+
+	SM4_CRYPT_BLK8(v0, v1, v2, v3, v4, v5, v6, v7);
+
+	st1		{v0.16b-v3.16b}, [x1], #64;
+	st1		{v4.16b-v7.16b}, [x1], #64;
+
+	cbz		w3, .Lcrypt_end;
+	b		.Lcrypt_loop_blk;
+
+.Lcrypt_tail8:
+	add		w3, w3, #8;
+	cmp		w3, #4;
+	blt		.Lcrypt_tail4;
+
+	sub		w3, w3, #4;
+
+	ld1		{v0.16b-v3.16b}, [x2], #64;
+	SM4_CRYPT_BLK4(v0, v1, v2, v3);
+	st1		{v0.16b-v3.16b}, [x1], #64;
+
+	cbz		w3, .Lcrypt_end;
+
+.Lcrypt_tail4:
+	sub		w3, w3, #1;
+
+	ld1		{v0.16b}, [x2], #16;
+	SM4_CRYPT_BLK(v0);
+	st1		{v0.16b}, [x1], #16;
+
+	cbnz		w3, .Lcrypt_tail4;
+
+.Lcrypt_end:
+	ret;
+SYM_FUNC_END(sm4_ce_crypt)
+
+.align 3
+SYM_FUNC_START(sm4_ce_cbc_enc)
+	/* input:
+	 *   x0: round key array, CTX
+	 *   x1: dst
+	 *   x2: src
+	 *   x3: iv (big endian, 128 bit)
+	 *   w4: nblocks
+	 */
+	PREPARE;
+
+	ld1		{RIV.16b}, [x3];
+
+.Lcbc_enc_loop:
+	sub		w4, w4, #1;
+
+	ld1		{RTMP0.16b}, [x2], #16;
+	eor		RIV.16b, RIV.16b, RTMP0.16b;
+
+	SM4_CRYPT_BLK(RIV);
+
+	st1		{RIV.16b}, [x1], #16;
+
+	cbnz		w4, .Lcbc_enc_loop;
+
+	/* store new IV */
+	st1		{RIV.16b}, [x3];
+
+	ret;
+SYM_FUNC_END(sm4_ce_cbc_enc)
+
+.align 3
+SYM_FUNC_START(sm4_ce_cbc_dec)
+	/* input:
+	 *   x0: round key array, CTX
+	 *   x1: dst
+	 *   x2: src
+	 *   x3: iv (big endian, 128 bit)
+	 *   w4: nblocks
+	 */
+	PREPARE;
+
+	ld1		{RIV.16b}, [x3];
+
+.Lcbc_loop_blk:
+	sub		w4, w4, #8;
+	tbnz		w4, #31, .Lcbc_tail8;
+
+	ld1		{v0.16b-v3.16b}, [x2], #64;
+	ld1		{v4.16b-v7.16b}, [x2];
+
+	SM4_CRYPT_BLK8(v0, v1, v2, v3, v4, v5, v6, v7);
+
+	sub		x2, x2, #64;
+	eor		v0.16b, v0.16b, RIV.16b;
+	ld1		{RTMP0.16b-RTMP3.16b}, [x2], #64;
+	eor		v1.16b, v1.16b, RTMP0.16b;
+	eor		v2.16b, v2.16b, RTMP1.16b;
+	eor		v3.16b, v3.16b, RTMP2.16b;
+	st1		{v0.16b-v3.16b}, [x1], #64;
+
+	eor		v4.16b, v4.16b, RTMP3.16b;
+	ld1		{RTMP0.16b-RTMP3.16b}, [x2], #64;
+	eor		v5.16b, v5.16b, RTMP0.16b;
+	eor		v6.16b, v6.16b, RTMP1.16b;
+	eor		v7.16b, v7.16b, RTMP2.16b;
+
+	mov		RIV.16b, RTMP3.16b;
+	st1		{v4.16b-v7.16b}, [x1], #64;
+
+	cbz		w4, .Lcbc_end;
+	b		.Lcbc_loop_blk;
+
+.Lcbc_tail8:
+	add		w4, w4, #8;
+	cmp		w4, #4;
+	blt		.Lcbc_tail4;
+
+	sub		w4, w4, #4;
+
+	ld1		{v0.16b-v3.16b}, [x2];
+
+	SM4_CRYPT_BLK4(v0, v1, v2, v3);
+
+	eor		v0.16b, v0.16b, RIV.16b;
+	ld1		{RTMP0.16b-RTMP3.16b}, [x2], #64;
+	eor		v1.16b, v1.16b, RTMP0.16b;
+	eor		v2.16b, v2.16b, RTMP1.16b;
+	eor		v3.16b, v3.16b, RTMP2.16b;
+
+	mov		RIV.16b, RTMP3.16b;
+	st1		{v0.16b-v3.16b}, [x1], #64;
+
+	cbz		w4, .Lcbc_end;
+
+.Lcbc_tail4:
+	sub		w4, w4, #1;
+
+	ld1		{v0.16b}, [x2];
+
+	SM4_CRYPT_BLK(v0);
+
+	eor		v0.16b, v0.16b, RIV.16b;
+	ld1		{RIV.16b}, [x2], #16;
+	st1		{v0.16b}, [x1], #16;
+
+	cbnz		w4, .Lcbc_tail4;
+
+.Lcbc_end:
+	/* store new IV */
+	st1		{RIV.16b}, [x3];
+
+	ret;
+SYM_FUNC_END(sm4_ce_cbc_dec)
+
+.align 3
+SYM_FUNC_START(sm4_ce_cfb_enc)
+	/* input:
+	 *   x0: round key array, CTX
+	 *   x1: dst
+	 *   x2: src
+	 *   x3: iv (big endian, 128 bit)
+	 *   w4: nblocks
+	 */
+	PREPARE;
+
+	ld1		{RIV.16b}, [x3];
+
+.Lcfb_enc_loop:
+	sub		w4, w4, #1;
+
+	SM4_CRYPT_BLK(RIV);
+
+	ld1		{RTMP0.16b}, [x2], #16;
+	eor		RIV.16b, RIV.16b, RTMP0.16b;
+	st1		{RIV.16b}, [x1], #16;
+
+	cbnz		w4, .Lcfb_enc_loop;
+
+	/* store new IV */
+	st1		{RIV.16b}, [x3];
+
+	ret;
+SYM_FUNC_END(sm4_ce_cfb_enc)
+
+.align 3
+SYM_FUNC_START(sm4_ce_cfb_dec)
+	/* input:
+	 *   x0: round key array, CTX
+	 *   x1: dst
+	 *   x2: src
+	 *   x3: iv (big endian, 128 bit)
+	 *   w4: nblocks
+	 */
+	PREPARE;
+
+	ld1		{v0.16b}, [x3];
+
+.Lcfb_loop_blk:
+	sub		w4, w4, #8;
+	tbnz		w4, #31, .Lcfb_tail8;
+
+	ld1		{v1.16b, v2.16b, v3.16b}, [x2], #48;
+	ld1		{v4.16b-v7.16b}, [x2];
+
+	SM4_CRYPT_BLK8(v0, v1, v2, v3, v4, v5, v6, v7);
+
+	sub		x2, x2, #48;
+	ld1		{RTMP0.16b-RTMP3.16b}, [x2], #64;
+	eor		v0.16b, v0.16b, RTMP0.16b;
+	eor		v1.16b, v1.16b, RTMP1.16b;
+	eor		v2.16b, v2.16b, RTMP2.16b;
+	eor		v3.16b, v3.16b, RTMP3.16b;
+	st1		{v0.16b-v3.16b}, [x1], #64;
+
+	ld1		{RTMP0.16b-RTMP3.16b}, [x2], #64;
+	eor		v4.16b, v4.16b, RTMP0.16b;
+	eor		v5.16b, v5.16b, RTMP1.16b;
+	eor		v6.16b, v6.16b, RTMP2.16b;
+	eor		v7.16b, v7.16b, RTMP3.16b;
+	st1		{v4.16b-v7.16b}, [x1], #64;
+
+	mov		v0.16b, RTMP3.16b;
+
+	cbz		w4, .Lcfb_end;
+	b		.Lcfb_loop_blk;
+
+.Lcfb_tail8:
+	add		w4, w4, #8;
+	cmp		w4, #4;
+	blt		.Lcfb_tail4;
+
+	sub		w4, w4, #4;
+
+	ld1		{v1.16b, v2.16b, v3.16b}, [x2];
+
+	SM4_CRYPT_BLK4(v0, v1, v2, v3);
+
+	ld1		{RTMP0.16b-RTMP3.16b}, [x2], #64;
+	eor		v0.16b, v0.16b, RTMP0.16b;
+	eor		v1.16b, v1.16b, RTMP1.16b;
+	eor		v2.16b, v2.16b, RTMP2.16b;
+	eor		v3.16b, v3.16b, RTMP3.16b;
+	st1		{v0.16b-v3.16b}, [x1], #64;
+
+	mov		v0.16b, RTMP3.16b;
+
+	cbz		w4, .Lcfb_end;
+
+.Lcfb_tail4:
+	sub		w4, w4, #1;
+
+	SM4_CRYPT_BLK(v0);
+
+	ld1		{RTMP0.16b}, [x2], #16;
+	eor		v0.16b, v0.16b, RTMP0.16b;
+	st1		{v0.16b}, [x1], #16;
+
+	mov		v0.16b, RTMP0.16b;
+
+	cbnz		w4, .Lcfb_tail4;
+
+.Lcfb_end:
+	/* store new IV */
+	st1		{v0.16b}, [x3];
+
+	ret;
+SYM_FUNC_END(sm4_ce_cfb_dec)
+
+.align 3
+SYM_FUNC_START(sm4_ce_ctr_enc)
+	/* input:
+	 *   x0: round key array, CTX
+	 *   x1: dst
+	 *   x2: src
+	 *   x3: ctr (big endian, 128 bit)
+	 *   w4: nblocks
+	 */
+	PREPARE;
+
+	ldp		x7, x8, [x3];
+	rev		x7, x7;
+	rev		x8, x8;
+
+.Lctr_loop_blk:
+	sub		w4, w4, #8;
+	tbnz		w4, #31, .Lctr_tail8;
+
+#define inc_le128(vctr)                     \
+	mov		vctr.d[1], x8;      \
+	mov		vctr.d[0], x7;      \
+	adds		x8, x8, #1;         \
+	adc		x7, x7, xzr;        \
+	rev64		vctr.16b, vctr.16b;
+
+	/* construct CTRs */
+	inc_le128(v0);			/* +0 */
+	inc_le128(v1);			/* +1 */
+	inc_le128(v2);			/* +2 */
+	inc_le128(v3);			/* +3 */
+	inc_le128(v4);			/* +4 */
+	inc_le128(v5);			/* +5 */
+	inc_le128(v6);			/* +6 */
+	inc_le128(v7);			/* +7 */
+
+	SM4_CRYPT_BLK8(v0, v1, v2, v3, v4, v5, v6, v7);
+
+	ld1		{RTMP0.16b-RTMP3.16b}, [x2], #64;
+	eor		v0.16b, v0.16b, RTMP0.16b;
+	eor		v1.16b, v1.16b, RTMP1.16b;
+	eor		v2.16b, v2.16b, RTMP2.16b;
+	eor		v3.16b, v3.16b, RTMP3.16b;
+	st1		{v0.16b-v3.16b}, [x1], #64;
+
+	ld1		{RTMP0.16b-RTMP3.16b}, [x2], #64;
+	eor		v4.16b, v4.16b, RTMP0.16b;
+	eor		v5.16b, v5.16b, RTMP1.16b;
+	eor		v6.16b, v6.16b, RTMP2.16b;
+	eor		v7.16b, v7.16b, RTMP3.16b;
+	st1		{v4.16b-v7.16b}, [x1], #64;
+
+	cbz		w4, .Lctr_end;
+	b		.Lctr_loop_blk;
+
+.Lctr_tail8:
+	add		w4, w4, #8;
+	cmp		w4, #4;
+	blt		.Lctr_tail4;
+
+	sub		w4, w4, #4;
+
+	/* construct CTRs */
+	inc_le128(v0);			/* +0 */
+	inc_le128(v1);			/* +1 */
+	inc_le128(v2);			/* +2 */
+	inc_le128(v3);			/* +3 */
+
+	SM4_CRYPT_BLK4(v0, v1, v2, v3);
+
+	ld1		{RTMP0.16b-RTMP3.16b}, [x2], #64;
+	eor		v0.16b, v0.16b, RTMP0.16b;
+	eor		v1.16b, v1.16b, RTMP1.16b;
+	eor		v2.16b, v2.16b, RTMP2.16b;
+	eor		v3.16b, v3.16b, RTMP3.16b;
+	st1		{v0.16b-v3.16b}, [x1], #64;
+
+	cbz		w4, .Lctr_end;
+
+.Lctr_tail4:
+	sub		w4, w4, #1;
+
+	/* construct CTRs */
+	inc_le128(v0);
+
+	SM4_CRYPT_BLK(v0);
+
+	ld1		{RTMP0.16b}, [x2], #16;
+	eor		v0.16b, v0.16b, RTMP0.16b;
+	st1		{v0.16b}, [x1], #16;
+
+	cbnz		w4, .Lctr_tail4;
+
+.Lctr_end:
+	/* store new CTR */
+	rev		x7, x7;
+	rev		x8, x8;
+	stp		x7, x8, [x3];
+
+	ret;
+SYM_FUNC_END(sm4_ce_ctr_enc)
diff --git a/arch/arm64/crypto/sm4-ce-glue.c b/arch/arm64/crypto/sm4-ce-glue.c
index 9c93cfc4841b..496d55c0d01a 100644
--- a/arch/arm64/crypto/sm4-ce-glue.c
+++ b/arch/arm64/crypto/sm4-ce-glue.c
@@ -1,82 +1,372 @@
-// SPDX-License-Identifier: GPL-2.0
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * SM4 Cipher Algorithm, using ARMv8 Crypto Extensions
+ * as specified in
+ * https://tools.ietf.org/id/draft-ribose-cfrg-sm4-10.html
+ *
+ * Copyright (C) 2022, Alibaba Group.
+ * Copyright (C) 2022 Tianjia Zhang <tianjia.zhang@linux.alibaba.com>
+ */
 
+#include <linux/module.h>
+#include <linux/crypto.h>
+#include <linux/kernel.h>
+#include <linux/cpufeature.h>
 #include <asm/neon.h>
 #include <asm/simd.h>
-#include <crypto/sm4.h>
 #include <crypto/internal/simd.h>
-#include <linux/module.h>
-#include <linux/cpufeature.h>
-#include <linux/crypto.h>
-#include <linux/types.h>
+#include <crypto/internal/skcipher.h>
+#include <crypto/sm4.h>
 
-MODULE_ALIAS_CRYPTO("sm4");
-MODULE_ALIAS_CRYPTO("sm4-ce");
-MODULE_DESCRIPTION("SM4 symmetric cipher using ARMv8 Crypto Extensions");
-MODULE_AUTHOR("Ard Biesheuvel <ard.biesheuvel@linaro.org>");
-MODULE_LICENSE("GPL v2");
+#define BYTES2BLKS(nbytes)	((nbytes) >> 4)
+
+asmlinkage void sm4_ce_expand_key(const u8 *key, u32 *rkey_enc, u32 *rkey_dec,
+				  const u32 *fk, const u32 *ck);
+asmlinkage void sm4_ce_crypt_block(const u32 *rkey, u8 *dst, const u8 *src);
+asmlinkage void sm4_ce_crypt(const u32 *rkey, u8 *dst, const u8 *src,
+			     unsigned int nblks);
+asmlinkage void sm4_ce_cbc_enc(const u32 *rkey, u8 *dst, const u8 *src,
+			       u8 *iv, unsigned int nblks);
+asmlinkage void sm4_ce_cbc_dec(const u32 *rkey, u8 *dst, const u8 *src,
+			       u8 *iv, unsigned int nblks);
+asmlinkage void sm4_ce_cfb_enc(const u32 *rkey, u8 *dst, const u8 *src,
+			       u8 *iv, unsigned int nblks);
+asmlinkage void sm4_ce_cfb_dec(const u32 *rkey, u8 *dst, const u8 *src,
+			       u8 *iv, unsigned int nblks);
+asmlinkage void sm4_ce_ctr_enc(const u32 *rkey, u8 *dst, const u8 *src,
+			       u8 *iv, unsigned int nblks);
+
+static int sm4_setkey(struct crypto_skcipher *tfm, const u8 *key,
+		      unsigned int key_len)
+{
+	struct sm4_ctx *ctx = crypto_skcipher_ctx(tfm);
+
+	if (key_len != SM4_KEY_SIZE)
+		return -EINVAL;
+
+	sm4_ce_expand_key(key, ctx->rkey_enc, ctx->rkey_dec,
+			  crypto_sm4_fk, crypto_sm4_ck);
+	return 0;
+}
+
+static int sm4_ecb_do_crypt(struct skcipher_request *req, const u32 *rkey)
+{
+	struct skcipher_walk walk;
+	unsigned int nbytes;
+	int err;
+
+	err = skcipher_walk_virt(&walk, req, false);
+
+	while ((nbytes = walk.nbytes) > 0) {
+		const u8 *src = walk.src.virt.addr;
+		u8 *dst = walk.dst.virt.addr;
+		unsigned int nblks;
+
+		kernel_neon_begin();
+
+		nblks = BYTES2BLKS(nbytes);
+		if (nblks) {
+			sm4_ce_crypt(rkey, dst, src, nblks);
+			nbytes -= nblks * SM4_BLOCK_SIZE;
+		}
+
+		kernel_neon_end();
+
+		err = skcipher_walk_done(&walk, nbytes);
+	}
+
+	return err;
+}
+
+static int sm4_ecb_encrypt(struct skcipher_request *req)
+{
+	struct crypto_skcipher *tfm = crypto_skcipher_reqtfm(req);
+	struct sm4_ctx *ctx = crypto_skcipher_ctx(tfm);
+
+	return sm4_ecb_do_crypt(req, ctx->rkey_enc);
+}
+
+static int sm4_ecb_decrypt(struct skcipher_request *req)
+{
+	struct crypto_skcipher *tfm = crypto_skcipher_reqtfm(req);
+	struct sm4_ctx *ctx = crypto_skcipher_ctx(tfm);
+
+	return sm4_ecb_do_crypt(req, ctx->rkey_dec);
+}
+
+static int sm4_cbc_encrypt(struct skcipher_request *req)
+{
+	struct crypto_skcipher *tfm = crypto_skcipher_reqtfm(req);
+	struct sm4_ctx *ctx = crypto_skcipher_ctx(tfm);
+	struct skcipher_walk walk;
+	unsigned int nbytes;
+	int err;
+
+	err = skcipher_walk_virt(&walk, req, false);
+
+	while ((nbytes = walk.nbytes) > 0) {
+		const u8 *src = walk.src.virt.addr;
+		u8 *dst = walk.dst.virt.addr;
+		unsigned int nblks;
+
+		kernel_neon_begin();
+
+		nblks = BYTES2BLKS(nbytes);
+		if (nblks) {
+			sm4_ce_cbc_enc(ctx->rkey_enc, dst, src, walk.iv, nblks);
+			nbytes -= nblks * SM4_BLOCK_SIZE;
+		}
+
+		kernel_neon_end();
 
-asmlinkage void sm4_ce_do_crypt(const u32 *rk, void *out, const void *in);
+		err = skcipher_walk_done(&walk, nbytes);
+	}
+
+	return err;
+}
 
-static int sm4_ce_setkey(struct crypto_tfm *tfm, const u8 *key,
-		       unsigned int key_len)
+static int sm4_cbc_decrypt(struct skcipher_request *req)
 {
-	struct sm4_ctx *ctx = crypto_tfm_ctx(tfm);
+	struct crypto_skcipher *tfm = crypto_skcipher_reqtfm(req);
+	struct sm4_ctx *ctx = crypto_skcipher_ctx(tfm);
+	struct skcipher_walk walk;
+	unsigned int nbytes;
+	int err;
+
+	err = skcipher_walk_virt(&walk, req, false);
+
+	while ((nbytes = walk.nbytes) > 0) {
+		const u8 *src = walk.src.virt.addr;
+		u8 *dst = walk.dst.virt.addr;
+		unsigned int nblks;
+
+		kernel_neon_begin();
+
+		nblks = BYTES2BLKS(nbytes);
+		if (nblks) {
+			sm4_ce_cbc_dec(ctx->rkey_dec, dst, src, walk.iv, nblks);
+			nbytes -= nblks * SM4_BLOCK_SIZE;
+		}
+
+		kernel_neon_end();
+
+		err = skcipher_walk_done(&walk, nbytes);
+	}
 
-	return sm4_expandkey(ctx, key, key_len);
+	return err;
 }
 
-static void sm4_ce_encrypt(struct crypto_tfm *tfm, u8 *out, const u8 *in)
+static int sm4_cfb_encrypt(struct skcipher_request *req)
 {
-	const struct sm4_ctx *ctx = crypto_tfm_ctx(tfm);
+	struct crypto_skcipher *tfm = crypto_skcipher_reqtfm(req);
+	struct sm4_ctx *ctx = crypto_skcipher_ctx(tfm);
+	struct skcipher_walk walk;
+	unsigned int nbytes;
+	int err;
+
+	err = skcipher_walk_virt(&walk, req, false);
+
+	while ((nbytes = walk.nbytes) > 0) {
+		const u8 *src = walk.src.virt.addr;
+		u8 *dst = walk.dst.virt.addr;
+		unsigned int nblks;
 
-	if (!crypto_simd_usable()) {
-		sm4_crypt_block(ctx->rkey_enc, out, in);
-	} else {
 		kernel_neon_begin();
-		sm4_ce_do_crypt(ctx->rkey_enc, out, in);
+
+		nblks = BYTES2BLKS(nbytes);
+		if (nblks) {
+			sm4_ce_cfb_enc(ctx->rkey_enc, dst, src, walk.iv, nblks);
+			dst += nblks * SM4_BLOCK_SIZE;
+			src += nblks * SM4_BLOCK_SIZE;
+			nbytes -= nblks * SM4_BLOCK_SIZE;
+		}
+
+		/* tail */
+		if (walk.nbytes == walk.total && nbytes > 0) {
+			u8 keystream[SM4_BLOCK_SIZE];
+
+			sm4_ce_crypt_block(ctx->rkey_enc, keystream, walk.iv);
+			crypto_xor_cpy(dst, src, keystream, nbytes);
+			nbytes = 0;
+		}
+
 		kernel_neon_end();
+
+		err = skcipher_walk_done(&walk, nbytes);
 	}
+
+	return err;
 }
 
-static void sm4_ce_decrypt(struct crypto_tfm *tfm, u8 *out, const u8 *in)
+static int sm4_cfb_decrypt(struct skcipher_request *req)
 {
-	const struct sm4_ctx *ctx = crypto_tfm_ctx(tfm);
+	struct crypto_skcipher *tfm = crypto_skcipher_reqtfm(req);
+	struct sm4_ctx *ctx = crypto_skcipher_ctx(tfm);
+	struct skcipher_walk walk;
+	unsigned int nbytes;
+	int err;
+
+	err = skcipher_walk_virt(&walk, req, false);
+
+	while ((nbytes = walk.nbytes) > 0) {
+		const u8 *src = walk.src.virt.addr;
+		u8 *dst = walk.dst.virt.addr;
+		unsigned int nblks;
 
-	if (!crypto_simd_usable()) {
-		sm4_crypt_block(ctx->rkey_dec, out, in);
-	} else {
 		kernel_neon_begin();
-		sm4_ce_do_crypt(ctx->rkey_dec, out, in);
+
+		nblks = BYTES2BLKS(nbytes);
+		if (nblks) {
+			sm4_ce_cfb_dec(ctx->rkey_enc, dst, src, walk.iv, nblks);
+			dst += nblks * SM4_BLOCK_SIZE;
+			src += nblks * SM4_BLOCK_SIZE;
+			nbytes -= nblks * SM4_BLOCK_SIZE;
+		}
+
+		/* tail */
+		if (walk.nbytes == walk.total && nbytes > 0) {
+			u8 keystream[SM4_BLOCK_SIZE];
+
+			sm4_ce_crypt_block(ctx->rkey_enc, keystream, walk.iv);
+			crypto_xor_cpy(dst, src, keystream, nbytes);
+			nbytes = 0;
+		}
+
 		kernel_neon_end();
+
+		err = skcipher_walk_done(&walk, nbytes);
 	}
+
+	return err;
 }
 
-static struct crypto_alg sm4_ce_alg = {
-	.cra_name			= "sm4",
-	.cra_driver_name		= "sm4-ce",
-	.cra_priority			= 200,
-	.cra_flags			= CRYPTO_ALG_TYPE_CIPHER,
-	.cra_blocksize			= SM4_BLOCK_SIZE,
-	.cra_ctxsize			= sizeof(struct sm4_ctx),
-	.cra_module			= THIS_MODULE,
-	.cra_u.cipher = {
-		.cia_min_keysize	= SM4_KEY_SIZE,
-		.cia_max_keysize	= SM4_KEY_SIZE,
-		.cia_setkey		= sm4_ce_setkey,
-		.cia_encrypt		= sm4_ce_encrypt,
-		.cia_decrypt		= sm4_ce_decrypt
+static int sm4_ctr_crypt(struct skcipher_request *req)
+{
+	struct crypto_skcipher *tfm = crypto_skcipher_reqtfm(req);
+	struct sm4_ctx *ctx = crypto_skcipher_ctx(tfm);
+	struct skcipher_walk walk;
+	unsigned int nbytes;
+	int err;
+
+	err = skcipher_walk_virt(&walk, req, false);
+
+	while ((nbytes = walk.nbytes) > 0) {
+		const u8 *src = walk.src.virt.addr;
+		u8 *dst = walk.dst.virt.addr;
+		unsigned int nblks;
+
+		kernel_neon_begin();
+
+		nblks = BYTES2BLKS(nbytes);
+		if (nblks) {
+			sm4_ce_ctr_enc(ctx->rkey_enc, dst, src, walk.iv, nblks);
+			dst += nblks * SM4_BLOCK_SIZE;
+			src += nblks * SM4_BLOCK_SIZE;
+			nbytes -= nblks * SM4_BLOCK_SIZE;
+		}
+
+		/* tail */
+		if (walk.nbytes == walk.total && nbytes > 0) {
+			u8 keystream[SM4_BLOCK_SIZE];
+
+			sm4_ce_crypt_block(ctx->rkey_enc, keystream, walk.iv);
+			crypto_inc(walk.iv, SM4_BLOCK_SIZE);
+			crypto_xor_cpy(dst, src, keystream, nbytes);
+			nbytes = 0;
+		}
+
+		kernel_neon_end();
+
+		err = skcipher_walk_done(&walk, nbytes);
+	}
+
+	return err;
+}
+
+static struct skcipher_alg sm4_algs[] = {
+	{
+		.base = {
+			.cra_name		= "ecb(sm4)",
+			.cra_driver_name	= "ecb-sm4-ce",
+			.cra_priority		= 400,
+			.cra_blocksize		= SM4_BLOCK_SIZE,
+			.cra_ctxsize		= sizeof(struct sm4_ctx),
+			.cra_module		= THIS_MODULE,
+		},
+		.min_keysize	= SM4_KEY_SIZE,
+		.max_keysize	= SM4_KEY_SIZE,
+		.setkey		= sm4_setkey,
+		.encrypt	= sm4_ecb_encrypt,
+		.decrypt	= sm4_ecb_decrypt,
+	}, {
+		.base = {
+			.cra_name		= "cbc(sm4)",
+			.cra_driver_name	= "cbc-sm4-ce",
+			.cra_priority		= 400,
+			.cra_blocksize		= SM4_BLOCK_SIZE,
+			.cra_ctxsize		= sizeof(struct sm4_ctx),
+			.cra_module		= THIS_MODULE,
+		},
+		.min_keysize	= SM4_KEY_SIZE,
+		.max_keysize	= SM4_KEY_SIZE,
+		.ivsize		= SM4_BLOCK_SIZE,
+		.setkey		= sm4_setkey,
+		.encrypt	= sm4_cbc_encrypt,
+		.decrypt	= sm4_cbc_decrypt,
+	}, {
+		.base = {
+			.cra_name		= "cfb(sm4)",
+			.cra_driver_name	= "cfb-sm4-ce",
+			.cra_priority		= 400,
+			.cra_blocksize		= 1,
+			.cra_ctxsize		= sizeof(struct sm4_ctx),
+			.cra_module		= THIS_MODULE,
+		},
+		.min_keysize	= SM4_KEY_SIZE,
+		.max_keysize	= SM4_KEY_SIZE,
+		.ivsize		= SM4_BLOCK_SIZE,
+		.chunksize	= SM4_BLOCK_SIZE,
+		.setkey		= sm4_setkey,
+		.encrypt	= sm4_cfb_encrypt,
+		.decrypt	= sm4_cfb_decrypt,
+	}, {
+		.base = {
+			.cra_name		= "ctr(sm4)",
+			.cra_driver_name	= "ctr-sm4-ce",
+			.cra_priority		= 400,
+			.cra_blocksize		= 1,
+			.cra_ctxsize		= sizeof(struct sm4_ctx),
+			.cra_module		= THIS_MODULE,
+		},
+		.min_keysize	= SM4_KEY_SIZE,
+		.max_keysize	= SM4_KEY_SIZE,
+		.ivsize		= SM4_BLOCK_SIZE,
+		.chunksize	= SM4_BLOCK_SIZE,
+		.setkey		= sm4_setkey,
+		.encrypt	= sm4_ctr_crypt,
+		.decrypt	= sm4_ctr_crypt,
 	}
 };
 
-static int __init sm4_ce_mod_init(void)
+static int __init sm4_init(void)
 {
-	return crypto_register_alg(&sm4_ce_alg);
+	return crypto_register_skciphers(sm4_algs, ARRAY_SIZE(sm4_algs));
 }
 
-static void __exit sm4_ce_mod_fini(void)
+static void __exit sm4_exit(void)
 {
-	crypto_unregister_alg(&sm4_ce_alg);
+	crypto_unregister_skciphers(sm4_algs, ARRAY_SIZE(sm4_algs));
 }
 
-module_cpu_feature_match(SM4, sm4_ce_mod_init);
-module_exit(sm4_ce_mod_fini);
+module_cpu_feature_match(SM4, sm4_init);
+module_exit(sm4_exit);
+
+MODULE_DESCRIPTION("SM4 ECB/CBC/CFB/CTR using ARMv8 Crypto Extensions");
+MODULE_ALIAS_CRYPTO("sm4-ce");
+MODULE_ALIAS_CRYPTO("sm4");
+MODULE_ALIAS_CRYPTO("ecb(sm4)");
+MODULE_ALIAS_CRYPTO("cbc(sm4)");
+MODULE_ALIAS_CRYPTO("cfb(sm4)");
+MODULE_ALIAS_CRYPTO("ctr(sm4)");
+MODULE_AUTHOR("Tianjia Zhang <tianjia.zhang@linux.alibaba.com>");
+MODULE_LICENSE("GPL v2");
diff --git a/arch/arm64/crypto/sm4-neon-core.S b/arch/arm64/crypto/sm4-neon-core.S
new file mode 100644
index 000000000000..3d5256b354d2
--- /dev/null
+++ b/arch/arm64/crypto/sm4-neon-core.S
@@ -0,0 +1,487 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * SM4 Cipher Algorithm for ARMv8 NEON
+ * as specified in
+ * https://tools.ietf.org/id/draft-ribose-cfrg-sm4-10.html
+ *
+ * Copyright (C) 2022, Alibaba Group.
+ * Copyright (C) 2022 Tianjia Zhang <tianjia.zhang@linux.alibaba.com>
+ */
+
+#include <linux/linkage.h>
+#include <asm/assembler.h>
+
+/* Register macros */
+
+#define RTMP0	v8
+#define RTMP1	v9
+#define RTMP2	v10
+#define RTMP3	v11
+
+#define RX0	v12
+#define RX1	v13
+#define RKEY	v14
+#define RIV	v15
+
+/* Helper macros. */
+
+#define PREPARE                                                 \
+	adr_l		x5, crypto_sm4_sbox;                    \
+	ld1		{v16.16b-v19.16b}, [x5], #64;           \
+	ld1		{v20.16b-v23.16b}, [x5], #64;           \
+	ld1		{v24.16b-v27.16b}, [x5], #64;           \
+	ld1		{v28.16b-v31.16b}, [x5];
+
+#define transpose_4x4(s0, s1, s2, s3)                           \
+	zip1		RTMP0.4s, s0.4s, s1.4s;                 \
+	zip1		RTMP1.4s, s2.4s, s3.4s;                 \
+	zip2		RTMP2.4s, s0.4s, s1.4s;                 \
+	zip2		RTMP3.4s, s2.4s, s3.4s;                 \
+	zip1		s0.2d, RTMP0.2d, RTMP1.2d;              \
+	zip2		s1.2d, RTMP0.2d, RTMP1.2d;              \
+	zip1		s2.2d, RTMP2.2d, RTMP3.2d;              \
+	zip2		s3.2d, RTMP2.2d, RTMP3.2d;
+
+#define rotate_clockwise_90(s0, s1, s2, s3)                     \
+	zip1		RTMP0.4s, s1.4s, s0.4s;                 \
+	zip2		RTMP1.4s, s1.4s, s0.4s;                 \
+	zip1		RTMP2.4s, s3.4s, s2.4s;                 \
+	zip2		RTMP3.4s, s3.4s, s2.4s;                 \
+	zip1		s0.2d, RTMP2.2d, RTMP0.2d;              \
+	zip2		s1.2d, RTMP2.2d, RTMP0.2d;              \
+	zip1		s2.2d, RTMP3.2d, RTMP1.2d;              \
+	zip2		s3.2d, RTMP3.2d, RTMP1.2d;
+
+#define ROUND4(round, s0, s1, s2, s3)                           \
+	dup		RX0.4s, RKEY.s[round];                  \
+	/* rk ^ s1 ^ s2 ^ s3 */                                 \
+	eor		RTMP1.16b, s2.16b, s3.16b;              \
+	eor		RX0.16b, RX0.16b, s1.16b;               \
+	eor		RX0.16b, RX0.16b, RTMP1.16b;            \
+                                                                \
+	/* sbox, non-linear part */                             \
+	movi		RTMP3.16b, #64;  /* sizeof(sbox) / 4 */ \
+	tbl		RTMP0.16b, {v16.16b-v19.16b}, RX0.16b;  \
+	sub		RX0.16b, RX0.16b, RTMP3.16b;            \
+	tbx		RTMP0.16b, {v20.16b-v23.16b}, RX0.16b;  \
+	sub		RX0.16b, RX0.16b, RTMP3.16b;            \
+	tbx		RTMP0.16b, {v24.16b-v27.16b}, RX0.16b;  \
+	sub		RX0.16b, RX0.16b, RTMP3.16b;            \
+	tbx		RTMP0.16b, {v28.16b-v31.16b}, RX0.16b;  \
+                                                                \
+	/* linear part */                                       \
+	shl		RTMP1.4s, RTMP0.4s, #8;                 \
+	shl		RTMP2.4s, RTMP0.4s, #16;                \
+	shl		RTMP3.4s, RTMP0.4s, #24;                \
+	sri		RTMP1.4s, RTMP0.4s, #(32-8);            \
+	sri		RTMP2.4s, RTMP0.4s, #(32-16);           \
+	sri		RTMP3.4s, RTMP0.4s, #(32-24);           \
+	/* RTMP1 = x ^ rol32(x, 8) ^ rol32(x, 16) */            \
+	eor		RTMP1.16b, RTMP1.16b, RTMP0.16b;        \
+	eor		RTMP1.16b, RTMP1.16b, RTMP2.16b;        \
+	/* RTMP3 = x ^ rol32(x, 24) ^ rol32(RTMP1, 2) */        \
+	eor		RTMP3.16b, RTMP3.16b, RTMP0.16b;        \
+	shl		RTMP2.4s, RTMP1.4s, 2;                  \
+	sri		RTMP2.4s, RTMP1.4s, #(32-2);            \
+	eor		RTMP3.16b, RTMP3.16b, RTMP2.16b;        \
+	/* s0 ^= RTMP3 */                                       \
+	eor		s0.16b, s0.16b, RTMP3.16b;
+
+#define SM4_CRYPT_BLK4(b0, b1, b2, b3)                          \
+	rev32		b0.16b, b0.16b;                         \
+	rev32		b1.16b, b1.16b;                         \
+	rev32		b2.16b, b2.16b;                         \
+	rev32		b3.16b, b3.16b;                         \
+                                                                \
+	transpose_4x4(b0, b1, b2, b3);                          \
+                                                                \
+	mov		x6, 8;                                  \
+4:                                                              \
+	ld1		{RKEY.4s}, [x0], #16;                   \
+	subs		x6, x6, #1;                             \
+                                                                \
+	ROUND4(0, b0, b1, b2, b3);                              \
+	ROUND4(1, b1, b2, b3, b0);                              \
+	ROUND4(2, b2, b3, b0, b1);                              \
+	ROUND4(3, b3, b0, b1, b2);                              \
+                                                                \
+	bne		4b;                                     \
+                                                                \
+	rotate_clockwise_90(b0, b1, b2, b3);                    \
+	rev32		b0.16b, b0.16b;                         \
+	rev32		b1.16b, b1.16b;                         \
+	rev32		b2.16b, b2.16b;                         \
+	rev32		b3.16b, b3.16b;                         \
+                                                                \
+	/* repoint to rkey */                                   \
+	sub		x0, x0, #128;
+
+#define ROUND8(round, s0, s1, s2, s3, t0, t1, t2, t3)           \
+	/* rk ^ s1 ^ s2 ^ s3 */                                 \
+	dup		RX0.4s, RKEY.s[round];                  \
+	eor		RTMP0.16b, s2.16b, s3.16b;              \
+	mov		RX1.16b, RX0.16b;                       \
+	eor		RTMP1.16b, t2.16b, t3.16b;              \
+	eor		RX0.16b, RX0.16b, s1.16b;               \
+	eor		RX1.16b, RX1.16b, t1.16b;               \
+	eor		RX0.16b, RX0.16b, RTMP0.16b;            \
+	eor		RX1.16b, RX1.16b, RTMP1.16b;            \
+                                                                \
+	/* sbox, non-linear part */                             \
+	movi		RTMP3.16b, #64;  /* sizeof(sbox) / 4 */ \
+	tbl		RTMP0.16b, {v16.16b-v19.16b}, RX0.16b;  \
+	tbl		RTMP1.16b, {v16.16b-v19.16b}, RX1.16b;  \
+	sub		RX0.16b, RX0.16b, RTMP3.16b;            \
+	sub		RX1.16b, RX1.16b, RTMP3.16b;            \
+	tbx		RTMP0.16b, {v20.16b-v23.16b}, RX0.16b;  \
+	tbx		RTMP1.16b, {v20.16b-v23.16b}, RX1.16b;  \
+	sub		RX0.16b, RX0.16b, RTMP3.16b;            \
+	sub		RX1.16b, RX1.16b, RTMP3.16b;            \
+	tbx		RTMP0.16b, {v24.16b-v27.16b}, RX0.16b;  \
+	tbx		RTMP1.16b, {v24.16b-v27.16b}, RX1.16b;  \
+	sub		RX0.16b, RX0.16b, RTMP3.16b;            \
+	sub		RX1.16b, RX1.16b, RTMP3.16b;            \
+	tbx		RTMP0.16b, {v28.16b-v31.16b}, RX0.16b;  \
+	tbx		RTMP1.16b, {v28.16b-v31.16b}, RX1.16b;  \
+                                                                \
+	/* linear part */                                       \
+	shl		RX0.4s, RTMP0.4s, #8;                   \
+	shl		RX1.4s, RTMP1.4s, #8;                   \
+	shl		RTMP2.4s, RTMP0.4s, #16;                \
+	shl		RTMP3.4s, RTMP1.4s, #16;                \
+	sri		RX0.4s, RTMP0.4s, #(32 - 8);            \
+	sri		RX1.4s, RTMP1.4s, #(32 - 8);            \
+	sri		RTMP2.4s, RTMP0.4s, #(32 - 16);         \
+	sri		RTMP3.4s, RTMP1.4s, #(32 - 16);         \
+	/* RX = x ^ rol32(x, 8) ^ rol32(x, 16) */               \
+	eor		RX0.16b, RX0.16b, RTMP0.16b;            \
+	eor		RX1.16b, RX1.16b, RTMP1.16b;            \
+	eor		RX0.16b, RX0.16b, RTMP2.16b;            \
+	eor		RX1.16b, RX1.16b, RTMP3.16b;            \
+	/* RTMP0/1 ^= x ^ rol32(x, 24) ^ rol32(RX, 2) */        \
+	shl		RTMP2.4s, RTMP0.4s, #24;                \
+	shl		RTMP3.4s, RTMP1.4s, #24;                \
+	sri		RTMP2.4s, RTMP0.4s, #(32 - 24);         \
+	sri		RTMP3.4s, RTMP1.4s, #(32 - 24);         \
+	eor		RTMP0.16b, RTMP0.16b, RTMP2.16b;        \
+	eor		RTMP1.16b, RTMP1.16b, RTMP3.16b;        \
+	shl		RTMP2.4s, RX0.4s, #2;                   \
+	shl		RTMP3.4s, RX1.4s, #2;                   \
+	sri		RTMP2.4s, RX0.4s, #(32 - 2);            \
+	sri		RTMP3.4s, RX1.4s, #(32 - 2);            \
+	eor		RTMP0.16b, RTMP0.16b, RTMP2.16b;        \
+	eor		RTMP1.16b, RTMP1.16b, RTMP3.16b;        \
+	/* s0/t0 ^= RTMP0/1 */                                  \
+	eor		s0.16b, s0.16b, RTMP0.16b;              \
+	eor		t0.16b, t0.16b, RTMP1.16b;
+
+#define SM4_CRYPT_BLK8(b0, b1, b2, b3, b4, b5, b6, b7)          \
+	rev32		b0.16b, b0.16b;                         \
+	rev32		b1.16b, b1.16b;                         \
+	rev32		b2.16b, b2.16b;                         \
+	rev32		b3.16b, b3.16b;                         \
+	rev32		b4.16b, b4.16b;                         \
+	rev32		b5.16b, b5.16b;                         \
+	rev32		b6.16b, b6.16b;                         \
+	rev32		b7.16b, b7.16b;                         \
+                                                                \
+	transpose_4x4(b0, b1, b2, b3);                          \
+	transpose_4x4(b4, b5, b6, b7);                          \
+                                                                \
+	mov		x6, 8;                                  \
+8:                                                              \
+	ld1		{RKEY.4s}, [x0], #16;                   \
+	subs		x6, x6, #1;                             \
+                                                                \
+	ROUND8(0, b0, b1, b2, b3, b4, b5, b6, b7);              \
+	ROUND8(1, b1, b2, b3, b0, b5, b6, b7, b4);              \
+	ROUND8(2, b2, b3, b0, b1, b6, b7, b4, b5);              \
+	ROUND8(3, b3, b0, b1, b2, b7, b4, b5, b6);              \
+                                                                \
+	bne		8b;                                     \
+                                                                \
+	rotate_clockwise_90(b0, b1, b2, b3);                    \
+	rotate_clockwise_90(b4, b5, b6, b7);                    \
+	rev32		b0.16b, b0.16b;                         \
+	rev32		b1.16b, b1.16b;                         \
+	rev32		b2.16b, b2.16b;                         \
+	rev32		b3.16b, b3.16b;                         \
+	rev32		b4.16b, b4.16b;                         \
+	rev32		b5.16b, b5.16b;                         \
+	rev32		b6.16b, b6.16b;                         \
+	rev32		b7.16b, b7.16b;                         \
+                                                                \
+	/* repoint to rkey */                                   \
+	sub		x0, x0, #128;
+
+
+.align 3
+SYM_FUNC_START_LOCAL(__sm4_neon_crypt_blk1_4)
+	/* input:
+	 *   x0: round key array, CTX
+	 *   x1: dst
+	 *   x2: src
+	 *   w3: num blocks (1..4)
+	 */
+	PREPARE;
+
+	ld1		{v0.16b}, [x2], #16;
+	mov		v1.16b, v0.16b;
+	mov		v2.16b, v0.16b;
+	mov		v3.16b, v0.16b;
+	cmp		w3, #2;
+	blt		.Lblk4_load_input_done;
+	ld1		{v1.16b}, [x2], #16;
+	beq		.Lblk4_load_input_done;
+	ld1		{v2.16b}, [x2], #16;
+	cmp		w3, #3;
+	beq		.Lblk4_load_input_done;
+	ld1		{v3.16b}, [x2];
+
+.Lblk4_load_input_done:
+	SM4_CRYPT_BLK4(v0, v1, v2, v3);
+
+	st1		{v0.16b}, [x1], #16;
+	cmp		w3, #2;
+	blt		.Lblk4_store_output_done;
+	st1		{v1.16b}, [x1], #16;
+	beq		.Lblk4_store_output_done;
+	st1		{v2.16b}, [x1], #16;
+	cmp		w3, #3;
+	beq		.Lblk4_store_output_done;
+	st1		{v3.16b}, [x1];
+
+.Lblk4_store_output_done:
+	ret;
+SYM_FUNC_END(__sm4_neon_crypt_blk1_4)
+
+.align 3
+SYM_FUNC_START(sm4_neon_crypt_blk1_8)
+	/* input:
+	 *   x0: round key array, CTX
+	 *   x1: dst
+	 *   x2: src
+	 *   w3: num blocks (1..8)
+	 */
+	cmp		w3, #5;
+	blt		__sm4_neon_crypt_blk1_4;
+
+	PREPARE;
+
+	ld1		{v0.16b-v3.16b}, [x2], #64;
+	ld1		{v4.16b}, [x2], #16;
+	mov		v5.16b, v4.16b;
+	mov		v6.16b, v4.16b;
+	mov		v7.16b, v4.16b;
+	beq		.Lblk8_load_input_done;
+	ld1		{v5.16b}, [x2], #16;
+	cmp		w3, #7;
+	blt		.Lblk8_load_input_done;
+	ld1		{v6.16b}, [x2], #16;
+	beq		.Lblk8_load_input_done;
+	ld1		{v7.16b}, [x2];
+
+.Lblk8_load_input_done:
+	SM4_CRYPT_BLK8(v0, v1, v2, v3, v4, v5, v6, v7);
+
+	cmp		w3, #6;
+	st1		{v0.16b-v3.16b}, [x1], #64;
+	st1		{v4.16b}, [x1], #16;
+	blt		.Lblk8_store_output_done;
+	st1		{v5.16b}, [x1], #16;
+	beq		.Lblk8_store_output_done;
+	st1		{v6.16b}, [x1], #16;
+	cmp		w3, #7;
+	beq		.Lblk8_store_output_done;
+	st1		{v7.16b}, [x1];
+
+.Lblk8_store_output_done:
+	ret;
+SYM_FUNC_END(sm4_neon_crypt_blk1_8)
+
+.align 3
+SYM_FUNC_START(sm4_neon_crypt_blk8)
+	/* input:
+	 *   x0: round key array, CTX
+	 *   x1: dst
+	 *   x2: src
+	 *   w3: nblocks (multiples of 8)
+	 */
+	PREPARE;
+
+.Lcrypt_loop_blk:
+	subs		w3, w3, #8;
+	bmi		.Lcrypt_end;
+
+	ld1		{v0.16b-v3.16b}, [x2], #64;
+	ld1		{v4.16b-v7.16b}, [x2], #64;
+
+	SM4_CRYPT_BLK8(v0, v1, v2, v3, v4, v5, v6, v7);
+
+	st1		{v0.16b-v3.16b}, [x1], #64;
+	st1		{v4.16b-v7.16b}, [x1], #64;
+
+	b		.Lcrypt_loop_blk;
+
+.Lcrypt_end:
+	ret;
+SYM_FUNC_END(sm4_neon_crypt_blk8)
+
+.align 3
+SYM_FUNC_START(sm4_neon_cbc_dec_blk8)
+	/* input:
+	 *   x0: round key array, CTX
+	 *   x1: dst
+	 *   x2: src
+	 *   x3: iv (big endian, 128 bit)
+	 *   w4: nblocks (multiples of 8)
+	 */
+	PREPARE;
+
+	ld1		{RIV.16b}, [x3];
+
+.Lcbc_loop_blk:
+	subs		w4, w4, #8;
+	bmi		.Lcbc_end;
+
+	ld1		{v0.16b-v3.16b}, [x2], #64;
+	ld1		{v4.16b-v7.16b}, [x2];
+
+	SM4_CRYPT_BLK8(v0, v1, v2, v3, v4, v5, v6, v7);
+
+	sub		x2, x2, #64;
+	eor		v0.16b, v0.16b, RIV.16b;
+	ld1		{RTMP0.16b-RTMP3.16b}, [x2], #64;
+	eor		v1.16b, v1.16b, RTMP0.16b;
+	eor		v2.16b, v2.16b, RTMP1.16b;
+	eor		v3.16b, v3.16b, RTMP2.16b;
+	st1		{v0.16b-v3.16b}, [x1], #64;
+
+	eor		v4.16b, v4.16b, RTMP3.16b;
+	ld1		{RTMP0.16b-RTMP3.16b}, [x2], #64;
+	eor		v5.16b, v5.16b, RTMP0.16b;
+	eor		v6.16b, v6.16b, RTMP1.16b;
+	eor		v7.16b, v7.16b, RTMP2.16b;
+
+	mov		RIV.16b, RTMP3.16b;
+	st1		{v4.16b-v7.16b}, [x1], #64;
+
+	b		.Lcbc_loop_blk;
+
+.Lcbc_end:
+	/* store new IV */
+	st1		{RIV.16b}, [x3];
+
+	ret;
+SYM_FUNC_END(sm4_neon_cbc_dec_blk8)
+
+.align 3
+SYM_FUNC_START(sm4_neon_cfb_dec_blk8)
+	/* input:
+	 *   x0: round key array, CTX
+	 *   x1: dst
+	 *   x2: src
+	 *   x3: iv (big endian, 128 bit)
+	 *   w4: nblocks (multiples of 8)
+	 */
+	PREPARE;
+
+	ld1		{v0.16b}, [x3];
+
+.Lcfb_loop_blk:
+	subs		w4, w4, #8;
+	bmi		.Lcfb_end;
+
+	ld1		{v1.16b, v2.16b, v3.16b}, [x2], #48;
+	ld1		{v4.16b-v7.16b}, [x2];
+
+	SM4_CRYPT_BLK8(v0, v1, v2, v3, v4, v5, v6, v7);
+
+	sub		x2, x2, #48;
+	ld1		{RTMP0.16b-RTMP3.16b}, [x2], #64;
+	eor		v0.16b, v0.16b, RTMP0.16b;
+	eor		v1.16b, v1.16b, RTMP1.16b;
+	eor		v2.16b, v2.16b, RTMP2.16b;
+	eor		v3.16b, v3.16b, RTMP3.16b;
+	st1		{v0.16b-v3.16b}, [x1], #64;
+
+	ld1		{RTMP0.16b-RTMP3.16b}, [x2], #64;
+	eor		v4.16b, v4.16b, RTMP0.16b;
+	eor		v5.16b, v5.16b, RTMP1.16b;
+	eor		v6.16b, v6.16b, RTMP2.16b;
+	eor		v7.16b, v7.16b, RTMP3.16b;
+	st1		{v4.16b-v7.16b}, [x1], #64;
+
+	mov		v0.16b, RTMP3.16b;
+
+	b		.Lcfb_loop_blk;
+
+.Lcfb_end:
+	/* store new IV */
+	st1		{v0.16b}, [x3];
+
+	ret;
+SYM_FUNC_END(sm4_neon_cfb_dec_blk8)
+
+.align 3
+SYM_FUNC_START(sm4_neon_ctr_enc_blk8)
+	/* input:
+	 *   x0: round key array, CTX
+	 *   x1: dst
+	 *   x2: src
+	 *   x3: ctr (big endian, 128 bit)
+	 *   w4: nblocks (multiples of 8)
+	 */
+	PREPARE;
+
+	ldp		x7, x8, [x3];
+	rev		x7, x7;
+	rev		x8, x8;
+
+.Lctr_loop_blk:
+	subs		w4, w4, #8;
+	bmi		.Lctr_end;
+
+#define inc_le128(vctr)                     \
+	mov		vctr.d[1], x8;      \
+	mov		vctr.d[0], x7;      \
+	adds		x8, x8, #1;         \
+	adc		x7, x7, xzr;        \
+	rev64		vctr.16b, vctr.16b;
+
+	/* construct CTRs */
+	inc_le128(v0);			/* +0 */
+	inc_le128(v1);			/* +1 */
+	inc_le128(v2);			/* +2 */
+	inc_le128(v3);			/* +3 */
+	inc_le128(v4);			/* +4 */
+	inc_le128(v5);			/* +5 */
+	inc_le128(v6);			/* +6 */
+	inc_le128(v7);			/* +7 */
+
+	SM4_CRYPT_BLK8(v0, v1, v2, v3, v4, v5, v6, v7);
+
+	ld1		{RTMP0.16b-RTMP3.16b}, [x2], #64;
+	eor		v0.16b, v0.16b, RTMP0.16b;
+	eor		v1.16b, v1.16b, RTMP1.16b;
+	eor		v2.16b, v2.16b, RTMP2.16b;
+	eor		v3.16b, v3.16b, RTMP3.16b;
+	st1		{v0.16b-v3.16b}, [x1], #64;
+
+	ld1		{RTMP0.16b-RTMP3.16b}, [x2], #64;
+	eor		v4.16b, v4.16b, RTMP0.16b;
+	eor		v5.16b, v5.16b, RTMP1.16b;
+	eor		v6.16b, v6.16b, RTMP2.16b;
+	eor		v7.16b, v7.16b, RTMP3.16b;
+	st1		{v4.16b-v7.16b}, [x1], #64;
+
+	b		.Lctr_loop_blk;
+
+.Lctr_end:
+	/* store new CTR */
+	rev		x7, x7;
+	rev		x8, x8;
+	stp		x7, x8, [x3];
+
+	ret;
+SYM_FUNC_END(sm4_neon_ctr_enc_blk8)
diff --git a/arch/arm64/crypto/sm4-neon-glue.c b/arch/arm64/crypto/sm4-neon-glue.c
new file mode 100644
index 000000000000..03a6a6866a31
--- /dev/null
+++ b/arch/arm64/crypto/sm4-neon-glue.c
@@ -0,0 +1,442 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * SM4 Cipher Algorithm, using ARMv8 NEON
+ * as specified in
+ * https://tools.ietf.org/id/draft-ribose-cfrg-sm4-10.html
+ *
+ * Copyright (C) 2022, Alibaba Group.
+ * Copyright (C) 2022 Tianjia Zhang <tianjia.zhang@linux.alibaba.com>
+ */
+
+#include <linux/module.h>
+#include <linux/crypto.h>
+#include <linux/kernel.h>
+#include <linux/cpufeature.h>
+#include <asm/neon.h>
+#include <asm/simd.h>
+#include <crypto/internal/simd.h>
+#include <crypto/internal/skcipher.h>
+#include <crypto/sm4.h>
+
+#define BYTES2BLKS(nbytes)	((nbytes) >> 4)
+#define BYTES2BLK8(nbytes)	(((nbytes) >> 4) & ~(8 - 1))
+
+asmlinkage void sm4_neon_crypt_blk1_8(const u32 *rkey, u8 *dst, const u8 *src,
+				      unsigned int nblks);
+asmlinkage void sm4_neon_crypt_blk8(const u32 *rkey, u8 *dst, const u8 *src,
+				    unsigned int nblks);
+asmlinkage void sm4_neon_cbc_dec_blk8(const u32 *rkey, u8 *dst, const u8 *src,
+				      u8 *iv, unsigned int nblks);
+asmlinkage void sm4_neon_cfb_dec_blk8(const u32 *rkey, u8 *dst, const u8 *src,
+				      u8 *iv, unsigned int nblks);
+asmlinkage void sm4_neon_ctr_enc_blk8(const u32 *rkey, u8 *dst, const u8 *src,
+				      u8 *iv, unsigned int nblks);
+
+static int sm4_setkey(struct crypto_skcipher *tfm, const u8 *key,
+		      unsigned int key_len)
+{
+	struct sm4_ctx *ctx = crypto_skcipher_ctx(tfm);
+
+	return sm4_expandkey(ctx, key, key_len);
+}
+
+static int sm4_ecb_do_crypt(struct skcipher_request *req, const u32 *rkey)
+{
+	struct skcipher_walk walk;
+	unsigned int nbytes;
+	int err;
+
+	err = skcipher_walk_virt(&walk, req, false);
+
+	while ((nbytes = walk.nbytes) > 0) {
+		const u8 *src = walk.src.virt.addr;
+		u8 *dst = walk.dst.virt.addr;
+		unsigned int nblks;
+
+		kernel_neon_begin();
+
+		nblks = BYTES2BLK8(nbytes);
+		if (nblks) {
+			sm4_neon_crypt_blk8(rkey, dst, src, nblks);
+			dst += nblks * SM4_BLOCK_SIZE;
+			src += nblks * SM4_BLOCK_SIZE;
+			nbytes -= nblks * SM4_BLOCK_SIZE;
+		}
+
+		nblks = BYTES2BLKS(nbytes);
+		if (nblks) {
+			sm4_neon_crypt_blk1_8(rkey, dst, src, nblks);
+			nbytes -= nblks * SM4_BLOCK_SIZE;
+		}
+
+		kernel_neon_end();
+
+		err = skcipher_walk_done(&walk, nbytes);
+	}
+
+	return err;
+}
+
+static int sm4_ecb_encrypt(struct skcipher_request *req)
+{
+	struct crypto_skcipher *tfm = crypto_skcipher_reqtfm(req);
+	struct sm4_ctx *ctx = crypto_skcipher_ctx(tfm);
+
+	return sm4_ecb_do_crypt(req, ctx->rkey_enc);
+}
+
+static int sm4_ecb_decrypt(struct skcipher_request *req)
+{
+	struct crypto_skcipher *tfm = crypto_skcipher_reqtfm(req);
+	struct sm4_ctx *ctx = crypto_skcipher_ctx(tfm);
+
+	return sm4_ecb_do_crypt(req, ctx->rkey_dec);
+}
+
+static int sm4_cbc_encrypt(struct skcipher_request *req)
+{
+	struct crypto_skcipher *tfm = crypto_skcipher_reqtfm(req);
+	struct sm4_ctx *ctx = crypto_skcipher_ctx(tfm);
+	struct skcipher_walk walk;
+	unsigned int nbytes;
+	int err;
+
+	err = skcipher_walk_virt(&walk, req, false);
+
+	while ((nbytes = walk.nbytes) > 0) {
+		const u8 *iv = walk.iv;
+		const u8 *src = walk.src.virt.addr;
+		u8 *dst = walk.dst.virt.addr;
+
+		while (nbytes >= SM4_BLOCK_SIZE) {
+			crypto_xor_cpy(dst, src, iv, SM4_BLOCK_SIZE);
+			sm4_crypt_block(ctx->rkey_enc, dst, dst);
+			iv = dst;
+			src += SM4_BLOCK_SIZE;
+			dst += SM4_BLOCK_SIZE;
+			nbytes -= SM4_BLOCK_SIZE;
+		}
+		if (iv != walk.iv)
+			memcpy(walk.iv, iv, SM4_BLOCK_SIZE);
+
+		err = skcipher_walk_done(&walk, nbytes);
+	}
+
+	return err;
+}
+
+static int sm4_cbc_decrypt(struct skcipher_request *req)
+{
+	struct crypto_skcipher *tfm = crypto_skcipher_reqtfm(req);
+	struct sm4_ctx *ctx = crypto_skcipher_ctx(tfm);
+	struct skcipher_walk walk;
+	unsigned int nbytes;
+	int err;
+
+	err = skcipher_walk_virt(&walk, req, false);
+
+	while ((nbytes = walk.nbytes) > 0) {
+		const u8 *src = walk.src.virt.addr;
+		u8 *dst = walk.dst.virt.addr;
+		unsigned int nblks;
+
+		kernel_neon_begin();
+
+		nblks = BYTES2BLK8(nbytes);
+		if (nblks) {
+			sm4_neon_cbc_dec_blk8(ctx->rkey_dec, dst, src,
+					walk.iv, nblks);
+			dst += nblks * SM4_BLOCK_SIZE;
+			src += nblks * SM4_BLOCK_SIZE;
+			nbytes -= nblks * SM4_BLOCK_SIZE;
+		}
+
+		nblks = BYTES2BLKS(nbytes);
+		if (nblks) {
+			u8 keystream[SM4_BLOCK_SIZE * 8];
+			u8 iv[SM4_BLOCK_SIZE];
+			int i;
+
+			sm4_neon_crypt_blk1_8(ctx->rkey_dec, keystream,
+					src, nblks);
+
+			src += ((int)nblks - 2) * SM4_BLOCK_SIZE;
+			dst += (nblks - 1) * SM4_BLOCK_SIZE;
+			memcpy(iv, src + SM4_BLOCK_SIZE, SM4_BLOCK_SIZE);
+
+			for (i = nblks - 1; i > 0; i--) {
+				crypto_xor_cpy(dst, src,
+					&keystream[i * SM4_BLOCK_SIZE],
+					SM4_BLOCK_SIZE);
+				src -= SM4_BLOCK_SIZE;
+				dst -= SM4_BLOCK_SIZE;
+			}
+			crypto_xor_cpy(dst, walk.iv,
+					keystream, SM4_BLOCK_SIZE);
+			memcpy(walk.iv, iv, SM4_BLOCK_SIZE);
+			nbytes -= nblks * SM4_BLOCK_SIZE;
+		}
+
+		kernel_neon_end();
+
+		err = skcipher_walk_done(&walk, nbytes);
+	}
+
+	return err;
+}
+
+static int sm4_cfb_encrypt(struct skcipher_request *req)
+{
+	struct crypto_skcipher *tfm = crypto_skcipher_reqtfm(req);
+	struct sm4_ctx *ctx = crypto_skcipher_ctx(tfm);
+	struct skcipher_walk walk;
+	unsigned int nbytes;
+	int err;
+
+	err = skcipher_walk_virt(&walk, req, false);
+
+	while ((nbytes = walk.nbytes) > 0) {
+		u8 keystream[SM4_BLOCK_SIZE];
+		const u8 *iv = walk.iv;
+		const u8 *src = walk.src.virt.addr;
+		u8 *dst = walk.dst.virt.addr;
+
+		while (nbytes >= SM4_BLOCK_SIZE) {
+			sm4_crypt_block(ctx->rkey_enc, keystream, iv);
+			crypto_xor_cpy(dst, src, keystream, SM4_BLOCK_SIZE);
+			iv = dst;
+			src += SM4_BLOCK_SIZE;
+			dst += SM4_BLOCK_SIZE;
+			nbytes -= SM4_BLOCK_SIZE;
+		}
+		if (iv != walk.iv)
+			memcpy(walk.iv, iv, SM4_BLOCK_SIZE);
+
+		/* tail */
+		if (walk.nbytes == walk.total && nbytes > 0) {
+			sm4_crypt_block(ctx->rkey_enc, keystream, walk.iv);
+			crypto_xor_cpy(dst, src, keystream, nbytes);
+			nbytes = 0;
+		}
+
+		err = skcipher_walk_done(&walk, nbytes);
+	}
+
+	return err;
+}
+
+static int sm4_cfb_decrypt(struct skcipher_request *req)
+{
+	struct crypto_skcipher *tfm = crypto_skcipher_reqtfm(req);
+	struct sm4_ctx *ctx = crypto_skcipher_ctx(tfm);
+	struct skcipher_walk walk;
+	unsigned int nbytes;
+	int err;
+
+	err = skcipher_walk_virt(&walk, req, false);
+
+	while ((nbytes = walk.nbytes) > 0) {
+		const u8 *src = walk.src.virt.addr;
+		u8 *dst = walk.dst.virt.addr;
+		unsigned int nblks;
+
+		kernel_neon_begin();
+
+		nblks = BYTES2BLK8(nbytes);
+		if (nblks) {
+			sm4_neon_cfb_dec_blk8(ctx->rkey_enc, dst, src,
+					walk.iv, nblks);
+			dst += nblks * SM4_BLOCK_SIZE;
+			src += nblks * SM4_BLOCK_SIZE;
+			nbytes -= nblks * SM4_BLOCK_SIZE;
+		}
+
+		nblks = BYTES2BLKS(nbytes);
+		if (nblks) {
+			u8 keystream[SM4_BLOCK_SIZE * 8];
+
+			memcpy(keystream, walk.iv, SM4_BLOCK_SIZE);
+			if (nblks > 1)
+				memcpy(&keystream[SM4_BLOCK_SIZE], src,
+					(nblks - 1) * SM4_BLOCK_SIZE);
+			memcpy(walk.iv, src + (nblks - 1) * SM4_BLOCK_SIZE,
+				SM4_BLOCK_SIZE);
+
+			sm4_neon_crypt_blk1_8(ctx->rkey_enc, keystream,
+					keystream, nblks);
+
+			crypto_xor_cpy(dst, src, keystream,
+					nblks * SM4_BLOCK_SIZE);
+			dst += nblks * SM4_BLOCK_SIZE;
+			src += nblks * SM4_BLOCK_SIZE;
+			nbytes -= nblks * SM4_BLOCK_SIZE;
+		}
+
+		kernel_neon_end();
+
+		/* tail */
+		if (walk.nbytes == walk.total && nbytes > 0) {
+			u8 keystream[SM4_BLOCK_SIZE];
+
+			sm4_crypt_block(ctx->rkey_enc, keystream, walk.iv);
+			crypto_xor_cpy(dst, src, keystream, nbytes);
+			nbytes = 0;
+		}
+
+		err = skcipher_walk_done(&walk, nbytes);
+	}
+
+	return err;
+}
+
+static int sm4_ctr_crypt(struct skcipher_request *req)
+{
+	struct crypto_skcipher *tfm = crypto_skcipher_reqtfm(req);
+	struct sm4_ctx *ctx = crypto_skcipher_ctx(tfm);
+	struct skcipher_walk walk;
+	unsigned int nbytes;
+	int err;
+
+	err = skcipher_walk_virt(&walk, req, false);
+
+	while ((nbytes = walk.nbytes) > 0) {
+		const u8 *src = walk.src.virt.addr;
+		u8 *dst = walk.dst.virt.addr;
+		unsigned int nblks;
+
+		kernel_neon_begin();
+
+		nblks = BYTES2BLK8(nbytes);
+		if (nblks) {
+			sm4_neon_ctr_enc_blk8(ctx->rkey_enc, dst, src,
+					walk.iv, nblks);
+			dst += nblks * SM4_BLOCK_SIZE;
+			src += nblks * SM4_BLOCK_SIZE;
+			nbytes -= nblks * SM4_BLOCK_SIZE;
+		}
+
+		nblks = BYTES2BLKS(nbytes);
+		if (nblks) {
+			u8 keystream[SM4_BLOCK_SIZE * 8];
+			int i;
+
+			for (i = 0; i < nblks; i++) {
+				memcpy(&keystream[i * SM4_BLOCK_SIZE],
+					walk.iv, SM4_BLOCK_SIZE);
+				crypto_inc(walk.iv, SM4_BLOCK_SIZE);
+			}
+			sm4_neon_crypt_blk1_8(ctx->rkey_enc, keystream,
+					keystream, nblks);
+
+			crypto_xor_cpy(dst, src, keystream,
+					nblks * SM4_BLOCK_SIZE);
+			dst += nblks * SM4_BLOCK_SIZE;
+			src += nblks * SM4_BLOCK_SIZE;
+			nbytes -= nblks * SM4_BLOCK_SIZE;
+		}
+
+		kernel_neon_end();
+
+		/* tail */
+		if (walk.nbytes == walk.total && nbytes > 0) {
+			u8 keystream[SM4_BLOCK_SIZE];
+
+			sm4_crypt_block(ctx->rkey_enc, keystream, walk.iv);
+			crypto_inc(walk.iv, SM4_BLOCK_SIZE);
+			crypto_xor_cpy(dst, src, keystream, nbytes);
+			nbytes = 0;
+		}
+
+		err = skcipher_walk_done(&walk, nbytes);
+	}
+
+	return err;
+}
+
+static struct skcipher_alg sm4_algs[] = {
+	{
+		.base = {
+			.cra_name		= "ecb(sm4)",
+			.cra_driver_name	= "ecb-sm4-neon",
+			.cra_priority		= 200,
+			.cra_blocksize		= SM4_BLOCK_SIZE,
+			.cra_ctxsize		= sizeof(struct sm4_ctx),
+			.cra_module		= THIS_MODULE,
+		},
+		.min_keysize	= SM4_KEY_SIZE,
+		.max_keysize	= SM4_KEY_SIZE,
+		.setkey		= sm4_setkey,
+		.encrypt	= sm4_ecb_encrypt,
+		.decrypt	= sm4_ecb_decrypt,
+	}, {
+		.base = {
+			.cra_name		= "cbc(sm4)",
+			.cra_driver_name	= "cbc-sm4-neon",
+			.cra_priority		= 200,
+			.cra_blocksize		= SM4_BLOCK_SIZE,
+			.cra_ctxsize		= sizeof(struct sm4_ctx),
+			.cra_module		= THIS_MODULE,
+		},
+		.min_keysize	= SM4_KEY_SIZE,
+		.max_keysize	= SM4_KEY_SIZE,
+		.ivsize		= SM4_BLOCK_SIZE,
+		.setkey		= sm4_setkey,
+		.encrypt	= sm4_cbc_encrypt,
+		.decrypt	= sm4_cbc_decrypt,
+	}, {
+		.base = {
+			.cra_name		= "cfb(sm4)",
+			.cra_driver_name	= "cfb-sm4-neon",
+			.cra_priority		= 200,
+			.cra_blocksize		= 1,
+			.cra_ctxsize		= sizeof(struct sm4_ctx),
+			.cra_module		= THIS_MODULE,
+		},
+		.min_keysize	= SM4_KEY_SIZE,
+		.max_keysize	= SM4_KEY_SIZE,
+		.ivsize		= SM4_BLOCK_SIZE,
+		.chunksize	= SM4_BLOCK_SIZE,
+		.setkey		= sm4_setkey,
+		.encrypt	= sm4_cfb_encrypt,
+		.decrypt	= sm4_cfb_decrypt,
+	}, {
+		.base = {
+			.cra_name		= "ctr(sm4)",
+			.cra_driver_name	= "ctr-sm4-neon",
+			.cra_priority		= 200,
+			.cra_blocksize		= 1,
+			.cra_ctxsize		= sizeof(struct sm4_ctx),
+			.cra_module		= THIS_MODULE,
+		},
+		.min_keysize	= SM4_KEY_SIZE,
+		.max_keysize	= SM4_KEY_SIZE,
+		.ivsize		= SM4_BLOCK_SIZE,
+		.chunksize	= SM4_BLOCK_SIZE,
+		.setkey		= sm4_setkey,
+		.encrypt	= sm4_ctr_crypt,
+		.decrypt	= sm4_ctr_crypt,
+	}
+};
+
+static int __init sm4_init(void)
+{
+	return crypto_register_skciphers(sm4_algs, ARRAY_SIZE(sm4_algs));
+}
+
+static void __exit sm4_exit(void)
+{
+	crypto_unregister_skciphers(sm4_algs, ARRAY_SIZE(sm4_algs));
+}
+
+module_init(sm4_init);
+module_exit(sm4_exit);
+
+MODULE_DESCRIPTION("SM4 ECB/CBC/CFB/CTR using ARMv8 NEON");
+MODULE_ALIAS_CRYPTO("sm4-neon");
+MODULE_ALIAS_CRYPTO("sm4");
+MODULE_ALIAS_CRYPTO("ecb(sm4)");
+MODULE_ALIAS_CRYPTO("cbc(sm4)");
+MODULE_ALIAS_CRYPTO("cfb(sm4)");
+MODULE_ALIAS_CRYPTO("ctr(sm4)");
+MODULE_AUTHOR("Tianjia Zhang <tianjia.zhang@linux.alibaba.com>");
+MODULE_LICENSE("GPL v2");
diff --git a/arch/arm64/hyperv/mshyperv.c b/arch/arm64/hyperv/mshyperv.c
index bbbe351e9045..a406454578f0 100644
--- a/arch/arm64/hyperv/mshyperv.c
+++ b/arch/arm64/hyperv/mshyperv.c
@@ -38,7 +38,7 @@ static int __init hyperv_init(void)
 		return 0;
 
 	/* Setup the guest ID */
-	guest_id = generate_guest_id(0, LINUX_VERSION_CODE, 0);
+	guest_id = hv_generate_guest_id(LINUX_VERSION_CODE);
 	hv_set_vpreg(HV_REGISTER_GUEST_OSID, guest_id);
 
 	/* Get the features and hints from Hyper-V */
diff --git a/arch/arm64/include/asm/Kbuild b/arch/arm64/include/asm/Kbuild
index 64202010b700..5c8ee5a541d2 100644
--- a/arch/arm64/include/asm/Kbuild
+++ b/arch/arm64/include/asm/Kbuild
@@ -3,6 +3,8 @@ generic-y += early_ioremap.h
 generic-y += mcs_spinlock.h
 generic-y += qrwlock.h
 generic-y += qspinlock.h
+generic-y += parport.h
 generic-y += user.h
 
 generated-y += cpucaps.h
+generated-y += sysreg-defs.h
diff --git a/arch/arm64/include/asm/alternative-macros.h b/arch/arm64/include/asm/alternative-macros.h
index 7e157ab6cd50..3622e9f4fb44 100644
--- a/arch/arm64/include/asm/alternative-macros.h
+++ b/arch/arm64/include/asm/alternative-macros.h
@@ -2,10 +2,22 @@
 #ifndef __ASM_ALTERNATIVE_MACROS_H
 #define __ASM_ALTERNATIVE_MACROS_H
 
+#include <linux/const.h>
+#include <vdso/bits.h>
+
 #include <asm/cpucaps.h>
 #include <asm/insn-def.h>
 
-#define ARM64_CB_PATCH ARM64_NCAPS
+/*
+ * Binutils 2.27.0 can't handle a 'UL' suffix on constants, so for the assembly
+ * macros below we must use we must use `(1 << ARM64_CB_SHIFT)`.
+ */
+#define ARM64_CB_SHIFT	15
+#define ARM64_CB_BIT	BIT(ARM64_CB_SHIFT)
+
+#if ARM64_NCAPS >= ARM64_CB_BIT
+#error "cpucaps have overflown ARM64_CB_BIT"
+#endif
 
 #ifndef __ASSEMBLY__
 
@@ -73,8 +85,8 @@
 #define _ALTERNATIVE_CFG(oldinstr, newinstr, feature, cfg, ...)	\
 	__ALTERNATIVE_CFG(oldinstr, newinstr, feature, IS_ENABLED(cfg))
 
-#define ALTERNATIVE_CB(oldinstr, cb) \
-	__ALTERNATIVE_CFG_CB(oldinstr, ARM64_CB_PATCH, 1, cb)
+#define ALTERNATIVE_CB(oldinstr, feature, cb) \
+	__ALTERNATIVE_CFG_CB(oldinstr, (1 << ARM64_CB_SHIFT) | (feature), 1, cb)
 #else
 
 #include <asm/assembler.h>
@@ -82,7 +94,7 @@
 .macro altinstruction_entry orig_offset alt_offset feature orig_len alt_len
 	.word \orig_offset - .
 	.word \alt_offset - .
-	.hword \feature
+	.hword (\feature)
 	.byte \orig_len
 	.byte \alt_len
 .endm
@@ -141,10 +153,10 @@
 661:
 .endm
 
-.macro alternative_cb cb
+.macro alternative_cb cap, cb
 	.set .Lasm_alt_mode, 0
 	.pushsection .altinstructions, "a"
-	altinstruction_entry 661f, \cb, ARM64_CB_PATCH, 662f-661f, 0
+	altinstruction_entry 661f, \cb, (1 << ARM64_CB_SHIFT) | \cap, 662f-661f, 0
 	.popsection
 661:
 .endm
@@ -207,4 +219,46 @@ alternative_endif
 #define ALTERNATIVE(oldinstr, newinstr, ...)   \
 	_ALTERNATIVE_CFG(oldinstr, newinstr, __VA_ARGS__, 1)
 
+#ifndef __ASSEMBLY__
+
+#include <linux/types.h>
+
+static __always_inline bool
+alternative_has_feature_likely(unsigned long feature)
+{
+	compiletime_assert(feature < ARM64_NCAPS,
+			   "feature must be < ARM64_NCAPS");
+
+	asm_volatile_goto(
+	ALTERNATIVE_CB("b	%l[l_no]", %[feature], alt_cb_patch_nops)
+	:
+	: [feature] "i" (feature)
+	:
+	: l_no);
+
+	return true;
+l_no:
+	return false;
+}
+
+static __always_inline bool
+alternative_has_feature_unlikely(unsigned long feature)
+{
+	compiletime_assert(feature < ARM64_NCAPS,
+			   "feature must be < ARM64_NCAPS");
+
+	asm_volatile_goto(
+	ALTERNATIVE("nop", "b	%l[l_yes]", %[feature])
+	:
+	: [feature] "i" (feature)
+	:
+	: l_yes);
+
+	return false;
+l_yes:
+	return true;
+}
+
+#endif /* __ASSEMBLY__ */
+
 #endif /* __ASM_ALTERNATIVE_MACROS_H */
diff --git a/arch/arm64/include/asm/apple_m1_pmu.h b/arch/arm64/include/asm/apple_m1_pmu.h
new file mode 100644
index 000000000000..99483b19b99f
--- /dev/null
+++ b/arch/arm64/include/asm/apple_m1_pmu.h
@@ -0,0 +1,64 @@
+// SPDX-License-Identifier: GPL-2.0
+
+#ifndef __ASM_APPLE_M1_PMU_h
+#define __ASM_APPLE_M1_PMU_h
+
+#include <linux/bits.h>
+#include <asm/sysreg.h>
+
+/* Counters */
+#define SYS_IMP_APL_PMC0_EL1	sys_reg(3, 2, 15, 0, 0)
+#define SYS_IMP_APL_PMC1_EL1	sys_reg(3, 2, 15, 1, 0)
+#define SYS_IMP_APL_PMC2_EL1	sys_reg(3, 2, 15, 2, 0)
+#define SYS_IMP_APL_PMC3_EL1	sys_reg(3, 2, 15, 3, 0)
+#define SYS_IMP_APL_PMC4_EL1	sys_reg(3, 2, 15, 4, 0)
+#define SYS_IMP_APL_PMC5_EL1	sys_reg(3, 2, 15, 5, 0)
+#define SYS_IMP_APL_PMC6_EL1	sys_reg(3, 2, 15, 6, 0)
+#define SYS_IMP_APL_PMC7_EL1	sys_reg(3, 2, 15, 7, 0)
+#define SYS_IMP_APL_PMC8_EL1	sys_reg(3, 2, 15, 9, 0)
+#define SYS_IMP_APL_PMC9_EL1	sys_reg(3, 2, 15, 10, 0)
+
+/* Core PMC control register */
+#define SYS_IMP_APL_PMCR0_EL1	sys_reg(3, 1, 15, 0, 0)
+#define PMCR0_CNT_ENABLE_0_7	GENMASK(7, 0)
+#define PMCR0_IMODE		GENMASK(10, 8)
+#define PMCR0_IMODE_OFF		0
+#define PMCR0_IMODE_PMI		1
+#define PMCR0_IMODE_AIC		2
+#define PMCR0_IMODE_HALT	3
+#define PMCR0_IMODE_FIQ		4
+#define PMCR0_IACT		BIT(11)
+#define PMCR0_PMI_ENABLE_0_7	GENMASK(19, 12)
+#define PMCR0_STOP_CNT_ON_PMI	BIT(20)
+#define PMCR0_CNT_GLOB_L2C_EVT	BIT(21)
+#define PMCR0_DEFER_PMI_TO_ERET	BIT(22)
+#define PMCR0_ALLOW_CNT_EN_EL0	BIT(30)
+#define PMCR0_CNT_ENABLE_8_9	GENMASK(33, 32)
+#define PMCR0_PMI_ENABLE_8_9	GENMASK(45, 44)
+
+#define SYS_IMP_APL_PMCR1_EL1	sys_reg(3, 1, 15, 1, 0)
+#define PMCR1_COUNT_A64_EL0_0_7	GENMASK(15, 8)
+#define PMCR1_COUNT_A64_EL1_0_7	GENMASK(23, 16)
+#define PMCR1_COUNT_A64_EL0_8_9	GENMASK(41, 40)
+#define PMCR1_COUNT_A64_EL1_8_9	GENMASK(49, 48)
+
+#define SYS_IMP_APL_PMCR2_EL1	sys_reg(3, 1, 15, 2, 0)
+#define SYS_IMP_APL_PMCR3_EL1	sys_reg(3, 1, 15, 3, 0)
+#define SYS_IMP_APL_PMCR4_EL1	sys_reg(3, 1, 15, 4, 0)
+
+#define SYS_IMP_APL_PMESR0_EL1	sys_reg(3, 1, 15, 5, 0)
+#define PMESR0_EVT_CNT_2	GENMASK(7, 0)
+#define PMESR0_EVT_CNT_3	GENMASK(15, 8)
+#define PMESR0_EVT_CNT_4	GENMASK(23, 16)
+#define PMESR0_EVT_CNT_5	GENMASK(31, 24)
+
+#define SYS_IMP_APL_PMESR1_EL1	sys_reg(3, 1, 15, 6, 0)
+#define PMESR1_EVT_CNT_6	GENMASK(7, 0)
+#define PMESR1_EVT_CNT_7	GENMASK(15, 8)
+#define PMESR1_EVT_CNT_8	GENMASK(23, 16)
+#define PMESR1_EVT_CNT_9	GENMASK(31, 24)
+
+#define SYS_IMP_APL_PMSR_EL1	sys_reg(3, 1, 15, 13, 0)
+#define PMSR_OVERFLOW		GENMASK(9, 0)
+
+#endif /* __ASM_APPLE_M1_PMU_h */
diff --git a/arch/arm64/include/asm/arch_gicv3.h b/arch/arm64/include/asm/arch_gicv3.h
index 4ad22c3135db..48d4473e8eee 100644
--- a/arch/arm64/include/asm/arch_gicv3.h
+++ b/arch/arm64/include/asm/arch_gicv3.h
@@ -26,12 +26,6 @@
  * sets the GP register's most significant bits to 0 with an explicit cast.
  */
 
-static inline void gic_write_eoir(u32 irq)
-{
-	write_sysreg_s(irq, SYS_ICC_EOIR1_EL1);
-	isb();
-}
-
 static __always_inline void gic_write_dir(u32 irq)
 {
 	write_sysreg_s(irq, SYS_ICC_DIR_EL1);
@@ -53,17 +47,36 @@ static inline u64 gic_read_iar_common(void)
  * The gicv3 of ThunderX requires a modified version for reading the
  * IAR status to ensure data synchronization (access to icc_iar1_el1
  * is not sync'ed before and after).
+ *
+ * Erratum 38545
+ *
+ * When a IAR register read races with a GIC interrupt RELEASE event,
+ * GIC-CPU interface could wrongly return a valid INTID to the CPU
+ * for an interrupt that is already released(non activated) instead of 0x3ff.
+ *
+ * To workaround this, return a valid interrupt ID only if there is a change
+ * in the active priority list after the IAR read.
+ *
+ * Common function used for both the workarounds since,
+ * 1. On Thunderx 88xx 1.x both erratas are applicable.
+ * 2. Having extra nops doesn't add any side effects for Silicons where
+ *    erratum 23154 is not applicable.
  */
 static inline u64 gic_read_iar_cavium_thunderx(void)
 {
-	u64 irqstat;
+	u64 irqstat, apr;
 
+	apr = read_sysreg_s(SYS_ICC_AP1R0_EL1);
 	nops(8);
 	irqstat = read_sysreg_s(SYS_ICC_IAR1_EL1);
 	nops(4);
 	mb();
 
-	return irqstat;
+	/* Max priority groups implemented is only 32 */
+	if (likely(apr != read_sysreg_s(SYS_ICC_AP1R0_EL1)))
+		return irqstat;
+
+	return 0x3ff;
 }
 
 static inline void gic_write_ctlr(u32 val)
diff --git a/arch/arm64/include/asm/archrandom.h b/arch/arm64/include/asm/archrandom.h
index 09e43272ccb0..109e2a4454be 100644
--- a/arch/arm64/include/asm/archrandom.h
+++ b/arch/arm64/include/asm/archrandom.h
@@ -2,8 +2,6 @@
 #ifndef _ASM_ARCHRANDOM_H
 #define _ASM_ARCHRANDOM_H
 
-#ifdef CONFIG_ARCH_RANDOM
-
 #include <linux/arm-smccc.h>
 #include <linux/bug.h>
 #include <linux/kernel.h>
@@ -42,19 +40,41 @@ static inline bool __arm64_rndr(unsigned long *v)
 	return ok;
 }
 
-static inline bool __must_check arch_get_random_long(unsigned long *v)
+static inline bool __arm64_rndrrs(unsigned long *v)
 {
-	return false;
+	bool ok;
+
+	/*
+	 * Reads of RNDRRS set PSTATE.NZCV to 0b0000 on success,
+	 * and set PSTATE.NZCV to 0b0100 otherwise.
+	 */
+	asm volatile(
+		__mrs_s("%0", SYS_RNDRRS_EL0) "\n"
+	"	cset %w1, ne\n"
+	: "=r" (*v), "=r" (ok)
+	:
+	: "cc");
+
+	return ok;
 }
 
-static inline bool __must_check arch_get_random_int(unsigned int *v)
+static inline size_t __must_check arch_get_random_longs(unsigned long *v, size_t max_longs)
 {
-	return false;
+	/*
+	 * Only support the generic interface after we have detected
+	 * the system wide capability, avoiding complexity with the
+	 * cpufeature code and with potential scheduling between CPUs
+	 * with and without the feature.
+	 */
+	if (max_longs && cpus_have_const_cap(ARM64_HAS_RNG) && __arm64_rndr(v))
+		return 1;
+	return 0;
 }
 
-static inline bool __must_check arch_get_random_seed_long(unsigned long *v)
+static inline size_t __must_check arch_get_random_seed_longs(unsigned long *v, size_t max_longs)
 {
-	struct arm_smccc_res res;
+	if (!max_longs)
+		return 0;
 
 	/*
 	 * We prefer the SMCCC call, since its semantics (return actual
@@ -63,83 +83,78 @@ static inline bool __must_check arch_get_random_seed_long(unsigned long *v)
 	 * (the output of a pseudo RNG freshly seeded by a TRNG).
 	 */
 	if (smccc_trng_available) {
-		arm_smccc_1_1_invoke(ARM_SMCCC_TRNG_RND64, 64, &res);
+		struct arm_smccc_res res;
+
+		max_longs = min_t(size_t, 3, max_longs);
+		arm_smccc_1_1_invoke(ARM_SMCCC_TRNG_RND64, max_longs * 64, &res);
 		if ((int)res.a0 >= 0) {
-			*v = res.a3;
-			return true;
+			switch (max_longs) {
+			case 3:
+				*v++ = res.a1;
+				fallthrough;
+			case 2:
+				*v++ = res.a2;
+				fallthrough;
+			case 1:
+				*v++ = res.a3;
+				break;
+			}
+			return max_longs;
 		}
 	}
 
 	/*
-	 * Only support the generic interface after we have detected
-	 * the system wide capability, avoiding complexity with the
-	 * cpufeature code and with potential scheduling between CPUs
-	 * with and without the feature.
+	 * RNDRRS is not backed by an entropy source but by a DRBG that is
+	 * reseeded after each invocation. This is not a 100% fit but good
+	 * enough to implement this API if no other entropy source exists.
 	 */
-	if (cpus_have_const_cap(ARM64_HAS_RNG) && __arm64_rndr(v))
-		return true;
-
-	return false;
-}
-
-static inline bool __must_check arch_get_random_seed_int(unsigned int *v)
-{
-	struct arm_smccc_res res;
-	unsigned long val;
-
-	if (smccc_trng_available) {
-		arm_smccc_1_1_invoke(ARM_SMCCC_TRNG_RND64, 32, &res);
-		if ((int)res.a0 >= 0) {
-			*v = res.a3 & GENMASK(31, 0);
-			return true;
-		}
-	}
-
-	if (cpus_have_const_cap(ARM64_HAS_RNG)) {
-		if (__arm64_rndr(&val)) {
-			*v = val;
-			return true;
-		}
-	}
+	if (cpus_have_const_cap(ARM64_HAS_RNG) && __arm64_rndrrs(v))
+		return 1;
 
-	return false;
+	return 0;
 }
 
 static inline bool __init __early_cpu_has_rndr(void)
 {
 	/* Open code as we run prior to the first call to cpufeature. */
 	unsigned long ftr = read_sysreg_s(SYS_ID_AA64ISAR0_EL1);
-	return (ftr >> ID_AA64ISAR0_RNDR_SHIFT) & 0xf;
+	return (ftr >> ID_AA64ISAR0_EL1_RNDR_SHIFT) & 0xf;
 }
 
-static inline bool __init __must_check
-arch_get_random_seed_long_early(unsigned long *v)
+static inline size_t __init __must_check
+arch_get_random_seed_longs_early(unsigned long *v, size_t max_longs)
 {
 	WARN_ON(system_state != SYSTEM_BOOTING);
 
+	if (!max_longs)
+		return 0;
+
 	if (smccc_trng_available) {
 		struct arm_smccc_res res;
 
-		arm_smccc_1_1_invoke(ARM_SMCCC_TRNG_RND64, 64, &res);
+		max_longs = min_t(size_t, 3, max_longs);
+		arm_smccc_1_1_invoke(ARM_SMCCC_TRNG_RND64, max_longs * 64, &res);
 		if ((int)res.a0 >= 0) {
-			*v = res.a3;
-			return true;
+			switch (max_longs) {
+			case 3:
+				*v++ = res.a1;
+				fallthrough;
+			case 2:
+				*v++ = res.a2;
+				fallthrough;
+			case 1:
+				*v++ = res.a3;
+				break;
+			}
+			return max_longs;
 		}
 	}
 
 	if (__early_cpu_has_rndr() && __arm64_rndr(v))
-		return true;
+		return 1;
 
-	return false;
-}
-#define arch_get_random_seed_long_early arch_get_random_seed_long_early
-
-#else /* !CONFIG_ARCH_RANDOM */
-
-static inline bool __init smccc_probe_trng(void)
-{
-	return false;
+	return 0;
 }
+#define arch_get_random_seed_longs_early arch_get_random_seed_longs_early
 
-#endif /* CONFIG_ARCH_RANDOM */
 #endif /* _ASM_ARCHRANDOM_H */
diff --git a/arch/arm64/include/asm/asm-bug.h b/arch/arm64/include/asm/asm-bug.h
index 03f52f84a4f3..c762038ba400 100644
--- a/arch/arm64/include/asm/asm-bug.h
+++ b/arch/arm64/include/asm/asm-bug.h
@@ -14,7 +14,7 @@
 	14472:	.string file;					\
 		.popsection;					\
 								\
-		.long 14472b - 14470b;				\
+		.long 14472b - .;				\
 		.short line;
 #else
 #define _BUGVERBOSE_LOCATION(file, line)
@@ -25,7 +25,7 @@
 #define __BUG_ENTRY(flags) 				\
 		.pushsection __bug_table,"aw";		\
 		.align 2;				\
-	14470:	.long 14471f - 14470b;			\
+	14470:	.long 14471f - .;			\
 _BUGVERBOSE_LOCATION(__FILE__, __LINE__)		\
 		.short flags; 				\
 		.popsection;				\
diff --git a/arch/arm64/include/asm/asm-extable.h b/arch/arm64/include/asm/asm-extable.h
index c39f2437e08e..980d1dd8e1a3 100644
--- a/arch/arm64/include/asm/asm-extable.h
+++ b/arch/arm64/include/asm/asm-extable.h
@@ -2,12 +2,27 @@
 #ifndef __ASM_ASM_EXTABLE_H
 #define __ASM_ASM_EXTABLE_H
 
+#include <linux/bits.h>
+#include <asm/gpr-num.h>
+
 #define EX_TYPE_NONE			0
-#define EX_TYPE_FIXUP			1
-#define EX_TYPE_BPF			2
-#define EX_TYPE_UACCESS_ERR_ZERO	3
+#define EX_TYPE_BPF			1
+#define EX_TYPE_UACCESS_ERR_ZERO	2
+#define EX_TYPE_KACCESS_ERR_ZERO	3
 #define EX_TYPE_LOAD_UNALIGNED_ZEROPAD	4
 
+/* Data fields for EX_TYPE_UACCESS_ERR_ZERO */
+#define EX_DATA_REG_ERR_SHIFT	0
+#define EX_DATA_REG_ERR		GENMASK(4, 0)
+#define EX_DATA_REG_ZERO_SHIFT	5
+#define EX_DATA_REG_ZERO	GENMASK(9, 5)
+
+/* Data fields for EX_TYPE_LOAD_UNALIGNED_ZEROPAD */
+#define EX_DATA_REG_DATA_SHIFT	0
+#define EX_DATA_REG_DATA	GENMASK(4, 0)
+#define EX_DATA_REG_ADDR_SHIFT	5
+#define EX_DATA_REG_ADDR	GENMASK(9, 5)
+
 #ifdef __ASSEMBLY__
 
 #define __ASM_EXTABLE_RAW(insn, fixup, type, data)	\
@@ -19,31 +34,45 @@
 	.short		(data);				\
 	.popsection;
 
+#define EX_DATA_REG(reg, gpr)	\
+	(.L__gpr_num_##gpr << EX_DATA_REG_##reg##_SHIFT)
+
+#define _ASM_EXTABLE_UACCESS_ERR_ZERO(insn, fixup, err, zero)		\
+	__ASM_EXTABLE_RAW(insn, fixup, 					\
+			  EX_TYPE_UACCESS_ERR_ZERO,			\
+			  (						\
+			    EX_DATA_REG(ERR, err) |			\
+			    EX_DATA_REG(ZERO, zero)			\
+			  ))
+
+#define _ASM_EXTABLE_UACCESS_ERR(insn, fixup, err)			\
+	_ASM_EXTABLE_UACCESS_ERR_ZERO(insn, fixup, err, wzr)
+
+#define _ASM_EXTABLE_UACCESS(insn, fixup)				\
+	_ASM_EXTABLE_UACCESS_ERR_ZERO(insn, fixup, wzr, wzr)
+
 /*
- * Create an exception table entry for `insn`, which will branch to `fixup`
+ * Create an exception table entry for uaccess `insn`, which will branch to `fixup`
  * when an unhandled fault is taken.
  */
-	.macro		_asm_extable, insn, fixup
-	__ASM_EXTABLE_RAW(\insn, \fixup, EX_TYPE_FIXUP, 0)
+	.macro          _asm_extable_uaccess, insn, fixup
+	_ASM_EXTABLE_UACCESS(\insn, \fixup)
 	.endm
 
 /*
  * Create an exception table entry for `insn` if `fixup` is provided. Otherwise
  * do nothing.
  */
-	.macro		_cond_extable, insn, fixup
-	.ifnc		\fixup,
-	_asm_extable	\insn, \fixup
+	.macro		_cond_uaccess_extable, insn, fixup
+	.ifnc			\fixup,
+	_asm_extable_uaccess	\insn, \fixup
 	.endif
 	.endm
 
 #else /* __ASSEMBLY__ */
 
-#include <linux/bits.h>
 #include <linux/stringify.h>
 
-#include <asm/gpr-num.h>
-
 #define __ASM_EXTABLE_RAW(insn, fixup, type, data)	\
 	".pushsection	__ex_table, \"a\"\n"		\
 	".align		2\n"				\
@@ -53,14 +82,6 @@
 	".short		(" data ")\n"			\
 	".popsection\n"
 
-#define _ASM_EXTABLE(insn, fixup) \
-	__ASM_EXTABLE_RAW(#insn, #fixup, __stringify(EX_TYPE_FIXUP), "0")
-
-#define EX_DATA_REG_ERR_SHIFT	0
-#define EX_DATA_REG_ERR		GENMASK(4, 0)
-#define EX_DATA_REG_ZERO_SHIFT	5
-#define EX_DATA_REG_ZERO	GENMASK(9, 5)
-
 #define EX_DATA_REG(reg, gpr)						\
 	"((.L__gpr_num_" #gpr ") << " __stringify(EX_DATA_REG_##reg##_SHIFT) ")"
 
@@ -73,13 +94,23 @@
 			    EX_DATA_REG(ZERO, zero)			\
 			  ")")
 
+#define _ASM_EXTABLE_KACCESS_ERR_ZERO(insn, fixup, err, zero)		\
+	__DEFINE_ASM_GPR_NUMS						\
+	__ASM_EXTABLE_RAW(#insn, #fixup, 				\
+			  __stringify(EX_TYPE_KACCESS_ERR_ZERO),	\
+			  "("						\
+			    EX_DATA_REG(ERR, err) " | "			\
+			    EX_DATA_REG(ZERO, zero)			\
+			  ")")
+
 #define _ASM_EXTABLE_UACCESS_ERR(insn, fixup, err)			\
 	_ASM_EXTABLE_UACCESS_ERR_ZERO(insn, fixup, err, wzr)
 
-#define EX_DATA_REG_DATA_SHIFT	0
-#define EX_DATA_REG_DATA	GENMASK(4, 0)
-#define EX_DATA_REG_ADDR_SHIFT	5
-#define EX_DATA_REG_ADDR	GENMASK(9, 5)
+#define _ASM_EXTABLE_UACCESS(insn, fixup)				\
+	_ASM_EXTABLE_UACCESS_ERR_ZERO(insn, fixup, wzr, wzr)
+
+#define _ASM_EXTABLE_KACCESS_ERR(insn, fixup, err)			\
+	_ASM_EXTABLE_KACCESS_ERR_ZERO(insn, fixup, err, wzr)
 
 #define _ASM_EXTABLE_LOAD_UNALIGNED_ZEROPAD(insn, fixup, data, addr)		\
 	__DEFINE_ASM_GPR_NUMS							\
diff --git a/arch/arm64/include/asm/asm-uaccess.h b/arch/arm64/include/asm/asm-uaccess.h
index 0557af834e03..75b211c98dea 100644
--- a/arch/arm64/include/asm/asm-uaccess.h
+++ b/arch/arm64/include/asm/asm-uaccess.h
@@ -61,7 +61,7 @@ alternative_else_nop_endif
 
 #define USER(l, x...)				\
 9999:	x;					\
-	_asm_extable	9999b, l
+	_asm_extable_uaccess	9999b, l
 
 /*
  * Generate the assembly for LDTR/STTR with exception table entries.
@@ -73,8 +73,8 @@ alternative_else_nop_endif
 8889:		ldtr	\reg2, [\addr, #8];
 		add	\addr, \addr, \post_inc;
 
-		_asm_extable	8888b,\l;
-		_asm_extable	8889b,\l;
+		_asm_extable_uaccess	8888b, \l;
+		_asm_extable_uaccess	8889b, \l;
 	.endm
 
 	.macro user_stp l, reg1, reg2, addr, post_inc
@@ -82,14 +82,14 @@ alternative_else_nop_endif
 8889:		sttr	\reg2, [\addr, #8];
 		add	\addr, \addr, \post_inc;
 
-		_asm_extable	8888b,\l;
-		_asm_extable	8889b,\l;
+		_asm_extable_uaccess	8888b,\l;
+		_asm_extable_uaccess	8889b,\l;
 	.endm
 
 	.macro user_ldst l, inst, reg, addr, post_inc
 8888:		\inst		\reg, [\addr];
 		add		\addr, \addr, \post_inc;
 
-		_asm_extable	8888b,\l;
+		_asm_extable_uaccess	8888b, \l;
 	.endm
 #endif
diff --git a/arch/arm64/include/asm/asm_pointer_auth.h b/arch/arm64/include/asm/asm_pointer_auth.h
index f1bba5fc61c4..13ecc79854ee 100644
--- a/arch/arm64/include/asm/asm_pointer_auth.h
+++ b/arch/arm64/include/asm/asm_pointer_auth.h
@@ -59,7 +59,10 @@ alternative_else_nop_endif
 
 	.macro __ptrauth_keys_init_cpu tsk, tmp1, tmp2, tmp3
 	mrs	\tmp1, id_aa64isar1_el1
-	ubfx	\tmp1, \tmp1, #ID_AA64ISAR1_APA_SHIFT, #8
+	ubfx	\tmp1, \tmp1, #ID_AA64ISAR1_EL1_APA_SHIFT, #8
+	mrs_s	\tmp2, SYS_ID_AA64ISAR2_EL1
+	ubfx	\tmp2, \tmp2, #ID_AA64ISAR2_EL1_APA3_SHIFT, #4
+	orr	\tmp1, \tmp1, \tmp2
 	cbz	\tmp1, .Lno_addr_auth\@
 	mov_q	\tmp1, (SCTLR_ELx_ENIA | SCTLR_ELx_ENIB | \
 			SCTLR_ELx_ENDA | SCTLR_ELx_ENDB)
diff --git a/arch/arm64/include/asm/assembler.h b/arch/arm64/include/asm/assembler.h
index 136d13f3d6e9..e5957a53be39 100644
--- a/arch/arm64/include/asm/assembler.h
+++ b/arch/arm64/include/asm/assembler.h
@@ -109,6 +109,13 @@
 	.endm
 
 /*
+ * Clear Branch History instruction
+ */
+	.macro clearbhb
+	hint	#22
+	.endm
+
+/*
  * Speculation barrier
  */
 	.macro	sb
@@ -286,7 +293,7 @@ alternative_endif
 alternative_if_not ARM64_KVM_PROTECTED_MODE
 	ASM_BUG()
 alternative_else_nop_endif
-alternative_cb kvm_compute_final_ctr_el0
+alternative_cb ARM64_ALWAYS_SYSTEM, kvm_compute_final_ctr_el0
 	movz	\reg, #0
 	movk	\reg, #0, lsl #16
 	movk	\reg, #0, lsl #32
@@ -353,6 +360,20 @@ alternative_cb_end
 	.endm
 
 /*
+ * idmap_get_t0sz - get the T0SZ value needed to cover the ID map
+ *
+ * Calculate the maximum allowed value for TCR_EL1.T0SZ so that the
+ * entire ID map region can be mapped. As T0SZ == (64 - #bits used),
+ * this number conveniently equals the number of leading zeroes in
+ * the physical address of _end.
+ */
+	.macro	idmap_get_t0sz, reg
+	adrp	\reg, _end
+	orr	\reg, \reg, #(1 << VA_BITS_MIN) - 1
+	clz	\reg, \reg
+	.endm
+
+/*
  * tcr_compute_pa_size - set TCR.(I)PS to the highest supported
  * ID_AA64MMFR0_EL1.PARange value
  *
@@ -363,8 +384,8 @@ alternative_cb_end
 	.macro	tcr_compute_pa_size, tcr, pos, tmp0, tmp1
 	mrs	\tmp0, ID_AA64MMFR0_EL1
 	// Narrow PARange to fit the PS field in TCR_ELx
-	ubfx	\tmp0, \tmp0, #ID_AA64MMFR0_PARANGE_SHIFT, #3
-	mov	\tmp1, #ID_AA64MMFR0_PARANGE_MAX
+	ubfx	\tmp0, \tmp0, #ID_AA64MMFR0_EL1_PARANGE_SHIFT, #3
+	mov	\tmp1, #ID_AA64MMFR0_EL1_PARANGE_MAX
 	cmp	\tmp0, \tmp1
 	csel	\tmp0, \tmp1, \tmp0, hi
 	bfi	\tcr, \tmp0, \pos, #3
@@ -416,7 +437,7 @@ alternative_endif
 	b.lo	.Ldcache_op\@
 	dsb	\domain
 
-	_cond_extable .Ldcache_op\@, \fixup
+	_cond_uaccess_extable .Ldcache_op\@, \fixup
 	.endm
 
 /*
@@ -455,7 +476,19 @@ alternative_endif
 	dsb	ish
 	isb
 
-	_cond_extable .Licache_op\@, \fixup
+	_cond_uaccess_extable .Licache_op\@, \fixup
+	.endm
+
+/*
+ * load_ttbr1 - install @pgtbl as a TTBR1 page table
+ * pgtbl preserved
+ * tmp1/tmp2 clobbered, either may overlap with pgtbl
+ */
+	.macro		load_ttbr1, pgtbl, tmp1, tmp2
+	phys_to_ttbr	\tmp1, \pgtbl
+	offset_ttbr1 	\tmp1, \tmp2
+	msr		ttbr1_el1, \tmp1
+	isb
 	.endm
 
 /*
@@ -471,10 +504,7 @@ alternative_endif
 	isb
 	tlbi	vmalle1
 	dsb	nsh
-	phys_to_ttbr \tmp, \page_table
-	offset_ttbr1 \tmp, \tmp2
-	msr	ttbr1_el1, \tmp
-	isb
+	load_ttbr1 \page_table, \tmp, \tmp2
 	.endm
 
 /*
@@ -482,7 +512,7 @@ alternative_endif
  */
 	.macro	reset_pmuserenr_el0, tmpreg
 	mrs	\tmpreg, id_aa64dfr0_el1
-	sbfx	\tmpreg, \tmpreg, #ID_AA64DFR0_PMUVER_SHIFT, #4
+	sbfx	\tmpreg, \tmpreg, #ID_AA64DFR0_EL1_PMUVer_SHIFT, #4
 	cmp	\tmpreg, #1			// Skip if no PMU present
 	b.lt	9000f
 	msr	pmuserenr_el0, xzr		// Disable PMU access from EL0
@@ -494,7 +524,7 @@ alternative_endif
  */
 	.macro	reset_amuserenr_el0, tmpreg
 	mrs	\tmpreg, id_aa64pfr0_el1	// Check ID_AA64PFR0_EL1
-	ubfx	\tmpreg, \tmpreg, #ID_AA64PFR0_AMU_SHIFT, #4
+	ubfx	\tmpreg, \tmpreg, #ID_AA64PFR0_EL1_AMU_SHIFT, #4
 	cbz	\tmpreg, .Lskip_\@		// Skip if no AMU present
 	msr_s	SYS_AMUSERENR_EL0, xzr		// Disable AMU access from EL0
 .Lskip_\@:
@@ -535,11 +565,6 @@ alternative_endif
 #define EXPORT_SYMBOL_NOKASAN(name)	EXPORT_SYMBOL(name)
 #endif
 
-#ifdef CONFIG_KASAN_HW_TAGS
-#define EXPORT_SYMBOL_NOHWKASAN(name)
-#else
-#define EXPORT_SYMBOL_NOHWKASAN(name)	EXPORT_SYMBOL_NOKASAN(name)
-#endif
 	/*
 	 * Emit a 64-bit absolute little endian symbol reference in a way that
 	 * ensures that it will be resolved at build time, even when building a
@@ -587,7 +612,7 @@ alternative_endif
 	.macro	offset_ttbr1, ttbr, tmp
 #ifdef CONFIG_ARM64_VA_BITS_52
 	mrs_s	\tmp, SYS_ID_AA64MMFR2_EL1
-	and	\tmp, \tmp, #(0xf << ID_AA64MMFR2_LVA_SHIFT)
+	and	\tmp, \tmp, #(0xf << ID_AA64MMFR2_EL1_VARange_SHIFT)
 	cbnz	\tmp, .Lskipoffs_\@
 	orr	\ttbr, \ttbr, #TTBR1_BADDR_4852_OFFSET
 .Lskipoffs_\@ :
@@ -791,6 +816,16 @@ alternative_endif
 	.endm
 
 /*
+ * Branch Target Identifier (BTI)
+ */
+	.macro  bti, targets
+	.equ	.L__bti_targets_c, 34
+	.equ	.L__bti_targets_j, 36
+	.equ	.L__bti_targets_jc,38
+	hint	#.L__bti_targets_\targets
+	.endm
+
+/*
  * This macro emits a program property note section identifying
  * architecture features which require special handling, mainly for
  * use in assembly files included in the VDSO.
@@ -840,4 +875,50 @@ alternative_endif
 
 #endif /* GNU_PROPERTY_AARCH64_FEATURE_1_DEFAULT */
 
+	.macro __mitigate_spectre_bhb_loop      tmp
+#ifdef CONFIG_MITIGATE_SPECTRE_BRANCH_HISTORY
+alternative_cb ARM64_ALWAYS_SYSTEM, spectre_bhb_patch_loop_iter
+	mov	\tmp, #32		// Patched to correct the immediate
+alternative_cb_end
+.Lspectre_bhb_loop\@:
+	b	. + 4
+	subs	\tmp, \tmp, #1
+	b.ne	.Lspectre_bhb_loop\@
+	sb
+#endif /* CONFIG_MITIGATE_SPECTRE_BRANCH_HISTORY */
+	.endm
+
+	.macro mitigate_spectre_bhb_loop	tmp
+#ifdef CONFIG_MITIGATE_SPECTRE_BRANCH_HISTORY
+alternative_cb ARM64_ALWAYS_SYSTEM, spectre_bhb_patch_loop_mitigation_enable
+	b	.L_spectre_bhb_loop_done\@	// Patched to NOP
+alternative_cb_end
+	__mitigate_spectre_bhb_loop	\tmp
+.L_spectre_bhb_loop_done\@:
+#endif /* CONFIG_MITIGATE_SPECTRE_BRANCH_HISTORY */
+	.endm
+
+	/* Save/restores x0-x3 to the stack */
+	.macro __mitigate_spectre_bhb_fw
+#ifdef CONFIG_MITIGATE_SPECTRE_BRANCH_HISTORY
+	stp	x0, x1, [sp, #-16]!
+	stp	x2, x3, [sp, #-16]!
+	mov	w0, #ARM_SMCCC_ARCH_WORKAROUND_3
+alternative_cb ARM64_ALWAYS_SYSTEM, smccc_patch_fw_mitigation_conduit
+	nop					// Patched to SMC/HVC #0
+alternative_cb_end
+	ldp	x2, x3, [sp], #16
+	ldp	x0, x1, [sp], #16
+#endif /* CONFIG_MITIGATE_SPECTRE_BRANCH_HISTORY */
+	.endm
+
+	.macro mitigate_spectre_bhb_clear_insn
+#ifdef CONFIG_MITIGATE_SPECTRE_BRANCH_HISTORY
+alternative_cb ARM64_ALWAYS_SYSTEM, spectre_bhb_patch_clearbhb
+	/* Patched to NOP when not supported */
+	clearbhb
+	isb
+alternative_cb_end
+#endif /* CONFIG_MITIGATE_SPECTRE_BRANCH_HISTORY */
+	.endm
 #endif	/* __ASM_ASSEMBLER_H */
diff --git a/arch/arm64/include/asm/atomic_ll_sc.h b/arch/arm64/include/asm/atomic_ll_sc.h
index 13869b76b58c..0890e4f568fb 100644
--- a/arch/arm64/include/asm/atomic_ll_sc.h
+++ b/arch/arm64/include/asm/atomic_ll_sc.h
@@ -12,19 +12,6 @@
 
 #include <linux/stringify.h>
 
-#ifdef CONFIG_ARM64_LSE_ATOMICS
-#define __LL_SC_FALLBACK(asm_ops)					\
-"	b	3f\n"							\
-"	.subsection	1\n"						\
-"3:\n"									\
-asm_ops "\n"								\
-"	b	4f\n"							\
-"	.previous\n"							\
-"4:\n"
-#else
-#define __LL_SC_FALLBACK(asm_ops) asm_ops
-#endif
-
 #ifndef CONFIG_CC_HAS_K_CONSTRAINT
 #define K
 #endif
@@ -36,38 +23,36 @@ asm_ops "\n"								\
  */
 
 #define ATOMIC_OP(op, asm_op, constraint)				\
-static inline void							\
+static __always_inline void						\
 __ll_sc_atomic_##op(int i, atomic_t *v)					\
 {									\
 	unsigned long tmp;						\
 	int result;							\
 									\
 	asm volatile("// atomic_" #op "\n"				\
-	__LL_SC_FALLBACK(						\
-"	prfm	pstl1strm, %2\n"					\
-"1:	ldxr	%w0, %2\n"						\
-"	" #asm_op "	%w0, %w0, %w3\n"				\
-"	stxr	%w1, %w0, %2\n"						\
-"	cbnz	%w1, 1b\n")						\
+	"	prfm	pstl1strm, %2\n"				\
+	"1:	ldxr	%w0, %2\n"					\
+	"	" #asm_op "	%w0, %w0, %w3\n"			\
+	"	stxr	%w1, %w0, %2\n"					\
+	"	cbnz	%w1, 1b\n"					\
 	: "=&r" (result), "=&r" (tmp), "+Q" (v->counter)		\
 	: __stringify(constraint) "r" (i));				\
 }
 
 #define ATOMIC_OP_RETURN(name, mb, acq, rel, cl, op, asm_op, constraint)\
-static inline int							\
+static __always_inline int						\
 __ll_sc_atomic_##op##_return##name(int i, atomic_t *v)			\
 {									\
 	unsigned long tmp;						\
 	int result;							\
 									\
 	asm volatile("// atomic_" #op "_return" #name "\n"		\
-	__LL_SC_FALLBACK(						\
-"	prfm	pstl1strm, %2\n"					\
-"1:	ld" #acq "xr	%w0, %2\n"					\
-"	" #asm_op "	%w0, %w0, %w3\n"				\
-"	st" #rel "xr	%w1, %w0, %2\n"					\
-"	cbnz	%w1, 1b\n"						\
-"	" #mb )								\
+	"	prfm	pstl1strm, %2\n"				\
+	"1:	ld" #acq "xr	%w0, %2\n"				\
+	"	" #asm_op "	%w0, %w0, %w3\n"			\
+	"	st" #rel "xr	%w1, %w0, %2\n"				\
+	"	cbnz	%w1, 1b\n"					\
+	"	" #mb							\
 	: "=&r" (result), "=&r" (tmp), "+Q" (v->counter)		\
 	: __stringify(constraint) "r" (i)				\
 	: cl);								\
@@ -76,20 +61,19 @@ __ll_sc_atomic_##op##_return##name(int i, atomic_t *v)			\
 }
 
 #define ATOMIC_FETCH_OP(name, mb, acq, rel, cl, op, asm_op, constraint) \
-static inline int							\
+static __always_inline int						\
 __ll_sc_atomic_fetch_##op##name(int i, atomic_t *v)			\
 {									\
 	unsigned long tmp;						\
 	int val, result;						\
 									\
 	asm volatile("// atomic_fetch_" #op #name "\n"			\
-	__LL_SC_FALLBACK(						\
-"	prfm	pstl1strm, %3\n"					\
-"1:	ld" #acq "xr	%w0, %3\n"					\
-"	" #asm_op "	%w1, %w0, %w4\n"				\
-"	st" #rel "xr	%w2, %w1, %3\n"					\
-"	cbnz	%w2, 1b\n"						\
-"	" #mb )								\
+	"	prfm	pstl1strm, %3\n"				\
+	"1:	ld" #acq "xr	%w0, %3\n"				\
+	"	" #asm_op "	%w1, %w0, %w4\n"			\
+	"	st" #rel "xr	%w2, %w1, %3\n"				\
+	"	cbnz	%w2, 1b\n"					\
+	"	" #mb							\
 	: "=&r" (result), "=&r" (val), "=&r" (tmp), "+Q" (v->counter)	\
 	: __stringify(constraint) "r" (i)				\
 	: cl);								\
@@ -135,38 +119,36 @@ ATOMIC_OPS(andnot, bic, )
 #undef ATOMIC_OP
 
 #define ATOMIC64_OP(op, asm_op, constraint)				\
-static inline void							\
+static __always_inline void						\
 __ll_sc_atomic64_##op(s64 i, atomic64_t *v)				\
 {									\
 	s64 result;							\
 	unsigned long tmp;						\
 									\
 	asm volatile("// atomic64_" #op "\n"				\
-	__LL_SC_FALLBACK(						\
-"	prfm	pstl1strm, %2\n"					\
-"1:	ldxr	%0, %2\n"						\
-"	" #asm_op "	%0, %0, %3\n"					\
-"	stxr	%w1, %0, %2\n"						\
-"	cbnz	%w1, 1b")						\
+	"	prfm	pstl1strm, %2\n"				\
+	"1:	ldxr	%0, %2\n"					\
+	"	" #asm_op "	%0, %0, %3\n"				\
+	"	stxr	%w1, %0, %2\n"					\
+	"	cbnz	%w1, 1b"					\
 	: "=&r" (result), "=&r" (tmp), "+Q" (v->counter)		\
 	: __stringify(constraint) "r" (i));				\
 }
 
 #define ATOMIC64_OP_RETURN(name, mb, acq, rel, cl, op, asm_op, constraint)\
-static inline long							\
+static __always_inline long						\
 __ll_sc_atomic64_##op##_return##name(s64 i, atomic64_t *v)		\
 {									\
 	s64 result;							\
 	unsigned long tmp;						\
 									\
 	asm volatile("// atomic64_" #op "_return" #name "\n"		\
-	__LL_SC_FALLBACK(						\
-"	prfm	pstl1strm, %2\n"					\
-"1:	ld" #acq "xr	%0, %2\n"					\
-"	" #asm_op "	%0, %0, %3\n"					\
-"	st" #rel "xr	%w1, %0, %2\n"					\
-"	cbnz	%w1, 1b\n"						\
-"	" #mb )								\
+	"	prfm	pstl1strm, %2\n"				\
+	"1:	ld" #acq "xr	%0, %2\n"				\
+	"	" #asm_op "	%0, %0, %3\n"				\
+	"	st" #rel "xr	%w1, %0, %2\n"				\
+	"	cbnz	%w1, 1b\n"					\
+	"	" #mb							\
 	: "=&r" (result), "=&r" (tmp), "+Q" (v->counter)		\
 	: __stringify(constraint) "r" (i)				\
 	: cl);								\
@@ -175,20 +157,19 @@ __ll_sc_atomic64_##op##_return##name(s64 i, atomic64_t *v)		\
 }
 
 #define ATOMIC64_FETCH_OP(name, mb, acq, rel, cl, op, asm_op, constraint)\
-static inline long							\
-__ll_sc_atomic64_fetch_##op##name(s64 i, atomic64_t *v)		\
+static __always_inline long						\
+__ll_sc_atomic64_fetch_##op##name(s64 i, atomic64_t *v)			\
 {									\
 	s64 result, val;						\
 	unsigned long tmp;						\
 									\
 	asm volatile("// atomic64_fetch_" #op #name "\n"		\
-	__LL_SC_FALLBACK(						\
-"	prfm	pstl1strm, %3\n"					\
-"1:	ld" #acq "xr	%0, %3\n"					\
-"	" #asm_op "	%1, %0, %4\n"					\
-"	st" #rel "xr	%w2, %1, %3\n"					\
-"	cbnz	%w2, 1b\n"						\
-"	" #mb )								\
+	"	prfm	pstl1strm, %3\n"				\
+	"1:	ld" #acq "xr	%0, %3\n"				\
+	"	" #asm_op "	%1, %0, %4\n"				\
+	"	st" #rel "xr	%w2, %1, %3\n"				\
+	"	cbnz	%w2, 1b\n"					\
+	"	" #mb							\
 	: "=&r" (result), "=&r" (val), "=&r" (tmp), "+Q" (v->counter)	\
 	: __stringify(constraint) "r" (i)				\
 	: cl);								\
@@ -233,22 +214,21 @@ ATOMIC64_OPS(andnot, bic, )
 #undef ATOMIC64_OP_RETURN
 #undef ATOMIC64_OP
 
-static inline s64
+static __always_inline s64
 __ll_sc_atomic64_dec_if_positive(atomic64_t *v)
 {
 	s64 result;
 	unsigned long tmp;
 
 	asm volatile("// atomic64_dec_if_positive\n"
-	__LL_SC_FALLBACK(
-"	prfm	pstl1strm, %2\n"
-"1:	ldxr	%0, %2\n"
-"	subs	%0, %0, #1\n"
-"	b.lt	2f\n"
-"	stlxr	%w1, %0, %2\n"
-"	cbnz	%w1, 1b\n"
-"	dmb	ish\n"
-"2:")
+	"	prfm	pstl1strm, %2\n"
+	"1:	ldxr	%0, %2\n"
+	"	subs	%0, %0, #1\n"
+	"	b.lt	2f\n"
+	"	stlxr	%w1, %0, %2\n"
+	"	cbnz	%w1, 1b\n"
+	"	dmb	ish\n"
+	"2:"
 	: "=&r" (result), "=&r" (tmp), "+Q" (v->counter)
 	:
 	: "cc", "memory");
@@ -257,7 +237,7 @@ __ll_sc_atomic64_dec_if_positive(atomic64_t *v)
 }
 
 #define __CMPXCHG_CASE(w, sfx, name, sz, mb, acq, rel, cl, constraint)	\
-static inline u##sz							\
+static __always_inline u##sz						\
 __ll_sc__cmpxchg_case_##name##sz(volatile void *ptr,			\
 					 unsigned long old,		\
 					 u##sz new)			\
@@ -274,7 +254,6 @@ __ll_sc__cmpxchg_case_##name##sz(volatile void *ptr,			\
 		old = (u##sz)old;					\
 									\
 	asm volatile(							\
-	__LL_SC_FALLBACK(						\
 	"	prfm	pstl1strm, %[v]\n"				\
 	"1:	ld" #acq "xr" #sfx "\t%" #w "[oldval], %[v]\n"		\
 	"	eor	%" #w "[tmp], %" #w "[oldval], %" #w "[old]\n"	\
@@ -282,7 +261,7 @@ __ll_sc__cmpxchg_case_##name##sz(volatile void *ptr,			\
 	"	st" #rel "xr" #sfx "\t%w[tmp], %" #w "[new], %[v]\n"	\
 	"	cbnz	%w[tmp], 1b\n"					\
 	"	" #mb "\n"						\
-	"2:")								\
+	"2:"								\
 	: [tmp] "=&r" (tmp), [oldval] "=&r" (oldval),			\
 	  [v] "+Q" (*(u##sz *)ptr)					\
 	: [old] __stringify(constraint) "r" (old), [new] "r" (new)	\
@@ -316,7 +295,7 @@ __CMPXCHG_CASE( ,  ,  mb_, 64, dmb ish,  , l, "memory", L)
 #undef __CMPXCHG_CASE
 
 #define __CMPXCHG_DBL(name, mb, rel, cl)				\
-static inline long							\
+static __always_inline long						\
 __ll_sc__cmpxchg_double##name(unsigned long old1,			\
 				      unsigned long old2,		\
 				      unsigned long new1,		\
@@ -326,7 +305,6 @@ __ll_sc__cmpxchg_double##name(unsigned long old1,			\
 	unsigned long tmp, ret;						\
 									\
 	asm volatile("// __cmpxchg_double" #name "\n"			\
-	__LL_SC_FALLBACK(						\
 	"	prfm	pstl1strm, %2\n"				\
 	"1:	ldxp	%0, %1, %2\n"					\
 	"	eor	%0, %0, %3\n"					\
@@ -336,7 +314,7 @@ __ll_sc__cmpxchg_double##name(unsigned long old1,			\
 	"	st" #rel "xp	%w0, %5, %6, %2\n"			\
 	"	cbnz	%w0, 1b\n"					\
 	"	" #mb "\n"						\
-	"2:")								\
+	"2:"								\
 	: "=&r" (tmp), "=&r" (ret), "+Q" (*(unsigned long *)ptr)	\
 	: "r" (old1), "r" (old2), "r" (new1), "r" (new2)		\
 	: cl);								\
diff --git a/arch/arm64/include/asm/atomic_lse.h b/arch/arm64/include/asm/atomic_lse.h
index da3280f639cd..52075e93de6c 100644
--- a/arch/arm64/include/asm/atomic_lse.h
+++ b/arch/arm64/include/asm/atomic_lse.h
@@ -11,13 +11,14 @@
 #define __ASM_ATOMIC_LSE_H
 
 #define ATOMIC_OP(op, asm_op)						\
-static inline void __lse_atomic_##op(int i, atomic_t *v)			\
+static __always_inline void						\
+__lse_atomic_##op(int i, atomic_t *v)					\
 {									\
 	asm volatile(							\
 	__LSE_PREAMBLE							\
-"	" #asm_op "	%w[i], %[v]\n"					\
-	: [i] "+r" (i), [v] "+Q" (v->counter)				\
-	: "r" (v));							\
+	"	" #asm_op "	%w[i], %[v]\n"				\
+	: [v] "+Q" (v->counter)						\
+	: [i] "r" (i));							\
 }
 
 ATOMIC_OP(andnot, stclr)
@@ -25,19 +26,28 @@ ATOMIC_OP(or, stset)
 ATOMIC_OP(xor, steor)
 ATOMIC_OP(add, stadd)
 
+static __always_inline void __lse_atomic_sub(int i, atomic_t *v)
+{
+	__lse_atomic_add(-i, v);
+}
+
 #undef ATOMIC_OP
 
 #define ATOMIC_FETCH_OP(name, mb, op, asm_op, cl...)			\
-static inline int __lse_atomic_fetch_##op##name(int i, atomic_t *v)	\
+static __always_inline int						\
+__lse_atomic_fetch_##op##name(int i, atomic_t *v)			\
 {									\
+	int old;							\
+									\
 	asm volatile(							\
 	__LSE_PREAMBLE							\
-"	" #asm_op #mb "	%w[i], %w[i], %[v]"				\
-	: [i] "+r" (i), [v] "+Q" (v->counter)				\
-	: "r" (v)							\
+	"	" #asm_op #mb "	%w[i], %w[old], %[v]"			\
+	: [v] "+Q" (v->counter),					\
+	  [old] "=r" (old)						\
+	: [i] "r" (i)							\
 	: cl);								\
 									\
-	return i;							\
+	return old;							\
 }
 
 #define ATOMIC_FETCH_OPS(op, asm_op)					\
@@ -54,51 +64,50 @@ ATOMIC_FETCH_OPS(add, ldadd)
 #undef ATOMIC_FETCH_OP
 #undef ATOMIC_FETCH_OPS
 
-#define ATOMIC_OP_ADD_RETURN(name, mb, cl...)				\
-static inline int __lse_atomic_add_return##name(int i, atomic_t *v)	\
+#define ATOMIC_FETCH_OP_SUB(name)					\
+static __always_inline int						\
+__lse_atomic_fetch_sub##name(int i, atomic_t *v)			\
 {									\
-	u32 tmp;							\
-									\
-	asm volatile(							\
-	__LSE_PREAMBLE							\
-	"	ldadd" #mb "	%w[i], %w[tmp], %[v]\n"			\
-	"	add	%w[i], %w[i], %w[tmp]"				\
-	: [i] "+r" (i), [v] "+Q" (v->counter), [tmp] "=&r" (tmp)	\
-	: "r" (v)							\
-	: cl);								\
+	return __lse_atomic_fetch_add##name(-i, v);			\
+}
+
+ATOMIC_FETCH_OP_SUB(_relaxed)
+ATOMIC_FETCH_OP_SUB(_acquire)
+ATOMIC_FETCH_OP_SUB(_release)
+ATOMIC_FETCH_OP_SUB(        )
+
+#undef ATOMIC_FETCH_OP_SUB
+
+#define ATOMIC_OP_ADD_SUB_RETURN(name)					\
+static __always_inline int						\
+__lse_atomic_add_return##name(int i, atomic_t *v)			\
+{									\
+	return __lse_atomic_fetch_add##name(i, v) + i;			\
+}									\
 									\
-	return i;							\
+static __always_inline int						\
+__lse_atomic_sub_return##name(int i, atomic_t *v)			\
+{									\
+	return __lse_atomic_fetch_sub(i, v) - i;			\
 }
 
-ATOMIC_OP_ADD_RETURN(_relaxed,   )
-ATOMIC_OP_ADD_RETURN(_acquire,  a, "memory")
-ATOMIC_OP_ADD_RETURN(_release,  l, "memory")
-ATOMIC_OP_ADD_RETURN(        , al, "memory")
+ATOMIC_OP_ADD_SUB_RETURN(_relaxed)
+ATOMIC_OP_ADD_SUB_RETURN(_acquire)
+ATOMIC_OP_ADD_SUB_RETURN(_release)
+ATOMIC_OP_ADD_SUB_RETURN(        )
 
-#undef ATOMIC_OP_ADD_RETURN
+#undef ATOMIC_OP_ADD_SUB_RETURN
 
-static inline void __lse_atomic_and(int i, atomic_t *v)
+static __always_inline void __lse_atomic_and(int i, atomic_t *v)
 {
-	asm volatile(
-	__LSE_PREAMBLE
-	"	mvn	%w[i], %w[i]\n"
-	"	stclr	%w[i], %[v]"
-	: [i] "+&r" (i), [v] "+Q" (v->counter)
-	: "r" (v));
+	return __lse_atomic_andnot(~i, v);
 }
 
 #define ATOMIC_FETCH_OP_AND(name, mb, cl...)				\
-static inline int __lse_atomic_fetch_and##name(int i, atomic_t *v)	\
+static __always_inline int						\
+__lse_atomic_fetch_and##name(int i, atomic_t *v)			\
 {									\
-	asm volatile(							\
-	__LSE_PREAMBLE							\
-	"	mvn	%w[i], %w[i]\n"					\
-	"	ldclr" #mb "	%w[i], %w[i], %[v]"			\
-	: [i] "+&r" (i), [v] "+Q" (v->counter)				\
-	: "r" (v)							\
-	: cl);								\
-									\
-	return i;							\
+	return __lse_atomic_fetch_andnot##name(~i, v);			\
 }
 
 ATOMIC_FETCH_OP_AND(_relaxed,   )
@@ -108,69 +117,15 @@ ATOMIC_FETCH_OP_AND(        , al, "memory")
 
 #undef ATOMIC_FETCH_OP_AND
 
-static inline void __lse_atomic_sub(int i, atomic_t *v)
-{
-	asm volatile(
-	__LSE_PREAMBLE
-	"	neg	%w[i], %w[i]\n"
-	"	stadd	%w[i], %[v]"
-	: [i] "+&r" (i), [v] "+Q" (v->counter)
-	: "r" (v));
-}
-
-#define ATOMIC_OP_SUB_RETURN(name, mb, cl...)				\
-static inline int __lse_atomic_sub_return##name(int i, atomic_t *v)	\
-{									\
-	u32 tmp;							\
-									\
-	asm volatile(							\
-	__LSE_PREAMBLE							\
-	"	neg	%w[i], %w[i]\n"					\
-	"	ldadd" #mb "	%w[i], %w[tmp], %[v]\n"			\
-	"	add	%w[i], %w[i], %w[tmp]"				\
-	: [i] "+&r" (i), [v] "+Q" (v->counter), [tmp] "=&r" (tmp)	\
-	: "r" (v)							\
-	: cl);							\
-									\
-	return i;							\
-}
-
-ATOMIC_OP_SUB_RETURN(_relaxed,   )
-ATOMIC_OP_SUB_RETURN(_acquire,  a, "memory")
-ATOMIC_OP_SUB_RETURN(_release,  l, "memory")
-ATOMIC_OP_SUB_RETURN(        , al, "memory")
-
-#undef ATOMIC_OP_SUB_RETURN
-
-#define ATOMIC_FETCH_OP_SUB(name, mb, cl...)				\
-static inline int __lse_atomic_fetch_sub##name(int i, atomic_t *v)	\
-{									\
-	asm volatile(							\
-	__LSE_PREAMBLE							\
-	"	neg	%w[i], %w[i]\n"					\
-	"	ldadd" #mb "	%w[i], %w[i], %[v]"			\
-	: [i] "+&r" (i), [v] "+Q" (v->counter)				\
-	: "r" (v)							\
-	: cl);								\
-									\
-	return i;							\
-}
-
-ATOMIC_FETCH_OP_SUB(_relaxed,   )
-ATOMIC_FETCH_OP_SUB(_acquire,  a, "memory")
-ATOMIC_FETCH_OP_SUB(_release,  l, "memory")
-ATOMIC_FETCH_OP_SUB(        , al, "memory")
-
-#undef ATOMIC_FETCH_OP_SUB
-
 #define ATOMIC64_OP(op, asm_op)						\
-static inline void __lse_atomic64_##op(s64 i, atomic64_t *v)		\
+static __always_inline void						\
+__lse_atomic64_##op(s64 i, atomic64_t *v)				\
 {									\
 	asm volatile(							\
 	__LSE_PREAMBLE							\
-"	" #asm_op "	%[i], %[v]\n"					\
-	: [i] "+r" (i), [v] "+Q" (v->counter)				\
-	: "r" (v));							\
+	"	" #asm_op "	%[i], %[v]\n"				\
+	: [v] "+Q" (v->counter)						\
+	: [i] "r" (i));							\
 }
 
 ATOMIC64_OP(andnot, stclr)
@@ -178,19 +133,28 @@ ATOMIC64_OP(or, stset)
 ATOMIC64_OP(xor, steor)
 ATOMIC64_OP(add, stadd)
 
+static __always_inline void __lse_atomic64_sub(s64 i, atomic64_t *v)
+{
+	__lse_atomic64_add(-i, v);
+}
+
 #undef ATOMIC64_OP
 
 #define ATOMIC64_FETCH_OP(name, mb, op, asm_op, cl...)			\
-static inline long __lse_atomic64_fetch_##op##name(s64 i, atomic64_t *v)\
+static __always_inline long						\
+__lse_atomic64_fetch_##op##name(s64 i, atomic64_t *v)			\
 {									\
+	s64 old;							\
+									\
 	asm volatile(							\
 	__LSE_PREAMBLE							\
-"	" #asm_op #mb "	%[i], %[i], %[v]"				\
-	: [i] "+r" (i), [v] "+Q" (v->counter)				\
-	: "r" (v)							\
+	"	" #asm_op #mb "	%[i], %[old], %[v]"			\
+	: [v] "+Q" (v->counter),					\
+	  [old] "=r" (old)						\
+	: [i] "r" (i) 							\
 	: cl);								\
 									\
-	return i;							\
+	return old;							\
 }
 
 #define ATOMIC64_FETCH_OPS(op, asm_op)					\
@@ -207,51 +171,50 @@ ATOMIC64_FETCH_OPS(add, ldadd)
 #undef ATOMIC64_FETCH_OP
 #undef ATOMIC64_FETCH_OPS
 
-#define ATOMIC64_OP_ADD_RETURN(name, mb, cl...)				\
-static inline long __lse_atomic64_add_return##name(s64 i, atomic64_t *v)\
+#define ATOMIC64_FETCH_OP_SUB(name)					\
+static __always_inline long						\
+__lse_atomic64_fetch_sub##name(s64 i, atomic64_t *v)			\
 {									\
-	unsigned long tmp;						\
-									\
-	asm volatile(							\
-	__LSE_PREAMBLE							\
-	"	ldadd" #mb "	%[i], %x[tmp], %[v]\n"			\
-	"	add	%[i], %[i], %x[tmp]"				\
-	: [i] "+r" (i), [v] "+Q" (v->counter), [tmp] "=&r" (tmp)	\
-	: "r" (v)							\
-	: cl);								\
+	return __lse_atomic64_fetch_add##name(-i, v);			\
+}
+
+ATOMIC64_FETCH_OP_SUB(_relaxed)
+ATOMIC64_FETCH_OP_SUB(_acquire)
+ATOMIC64_FETCH_OP_SUB(_release)
+ATOMIC64_FETCH_OP_SUB(        )
+
+#undef ATOMIC64_FETCH_OP_SUB
+
+#define ATOMIC64_OP_ADD_SUB_RETURN(name)				\
+static __always_inline long						\
+__lse_atomic64_add_return##name(s64 i, atomic64_t *v)			\
+{									\
+	return __lse_atomic64_fetch_add##name(i, v) + i;		\
+}									\
 									\
-	return i;							\
+static __always_inline long						\
+__lse_atomic64_sub_return##name(s64 i, atomic64_t *v)			\
+{									\
+	return __lse_atomic64_fetch_sub##name(i, v) - i;		\
 }
 
-ATOMIC64_OP_ADD_RETURN(_relaxed,   )
-ATOMIC64_OP_ADD_RETURN(_acquire,  a, "memory")
-ATOMIC64_OP_ADD_RETURN(_release,  l, "memory")
-ATOMIC64_OP_ADD_RETURN(        , al, "memory")
+ATOMIC64_OP_ADD_SUB_RETURN(_relaxed)
+ATOMIC64_OP_ADD_SUB_RETURN(_acquire)
+ATOMIC64_OP_ADD_SUB_RETURN(_release)
+ATOMIC64_OP_ADD_SUB_RETURN(        )
 
-#undef ATOMIC64_OP_ADD_RETURN
+#undef ATOMIC64_OP_ADD_SUB_RETURN
 
-static inline void __lse_atomic64_and(s64 i, atomic64_t *v)
+static __always_inline void __lse_atomic64_and(s64 i, atomic64_t *v)
 {
-	asm volatile(
-	__LSE_PREAMBLE
-	"	mvn	%[i], %[i]\n"
-	"	stclr	%[i], %[v]"
-	: [i] "+&r" (i), [v] "+Q" (v->counter)
-	: "r" (v));
+	return __lse_atomic64_andnot(~i, v);
 }
 
 #define ATOMIC64_FETCH_OP_AND(name, mb, cl...)				\
-static inline long __lse_atomic64_fetch_and##name(s64 i, atomic64_t *v)	\
+static __always_inline long						\
+__lse_atomic64_fetch_and##name(s64 i, atomic64_t *v)			\
 {									\
-	asm volatile(							\
-	__LSE_PREAMBLE							\
-	"	mvn	%[i], %[i]\n"					\
-	"	ldclr" #mb "	%[i], %[i], %[v]"			\
-	: [i] "+&r" (i), [v] "+Q" (v->counter)				\
-	: "r" (v)							\
-	: cl);								\
-									\
-	return i;							\
+	return __lse_atomic64_fetch_andnot##name(~i, v);		\
 }
 
 ATOMIC64_FETCH_OP_AND(_relaxed,   )
@@ -261,62 +224,7 @@ ATOMIC64_FETCH_OP_AND(        , al, "memory")
 
 #undef ATOMIC64_FETCH_OP_AND
 
-static inline void __lse_atomic64_sub(s64 i, atomic64_t *v)
-{
-	asm volatile(
-	__LSE_PREAMBLE
-	"	neg	%[i], %[i]\n"
-	"	stadd	%[i], %[v]"
-	: [i] "+&r" (i), [v] "+Q" (v->counter)
-	: "r" (v));
-}
-
-#define ATOMIC64_OP_SUB_RETURN(name, mb, cl...)				\
-static inline long __lse_atomic64_sub_return##name(s64 i, atomic64_t *v)	\
-{									\
-	unsigned long tmp;						\
-									\
-	asm volatile(							\
-	__LSE_PREAMBLE							\
-	"	neg	%[i], %[i]\n"					\
-	"	ldadd" #mb "	%[i], %x[tmp], %[v]\n"			\
-	"	add	%[i], %[i], %x[tmp]"				\
-	: [i] "+&r" (i), [v] "+Q" (v->counter), [tmp] "=&r" (tmp)	\
-	: "r" (v)							\
-	: cl);								\
-									\
-	return i;							\
-}
-
-ATOMIC64_OP_SUB_RETURN(_relaxed,   )
-ATOMIC64_OP_SUB_RETURN(_acquire,  a, "memory")
-ATOMIC64_OP_SUB_RETURN(_release,  l, "memory")
-ATOMIC64_OP_SUB_RETURN(        , al, "memory")
-
-#undef ATOMIC64_OP_SUB_RETURN
-
-#define ATOMIC64_FETCH_OP_SUB(name, mb, cl...)				\
-static inline long __lse_atomic64_fetch_sub##name(s64 i, atomic64_t *v)	\
-{									\
-	asm volatile(							\
-	__LSE_PREAMBLE							\
-	"	neg	%[i], %[i]\n"					\
-	"	ldadd" #mb "	%[i], %[i], %[v]"			\
-	: [i] "+&r" (i), [v] "+Q" (v->counter)				\
-	: "r" (v)							\
-	: cl);								\
-									\
-	return i;							\
-}
-
-ATOMIC64_FETCH_OP_SUB(_relaxed,   )
-ATOMIC64_FETCH_OP_SUB(_acquire,  a, "memory")
-ATOMIC64_FETCH_OP_SUB(_release,  l, "memory")
-ATOMIC64_FETCH_OP_SUB(        , al, "memory")
-
-#undef ATOMIC64_FETCH_OP_SUB
-
-static inline s64 __lse_atomic64_dec_if_positive(atomic64_t *v)
+static __always_inline s64 __lse_atomic64_dec_if_positive(atomic64_t *v)
 {
 	unsigned long tmp;
 
@@ -353,7 +261,7 @@ __lse__cmpxchg_case_##name##sz(volatile void *ptr,			\
 	"	mov	%" #w "[tmp], %" #w "[old]\n"			\
 	"	cas" #mb #sfx "\t%" #w "[tmp], %" #w "[new], %[v]\n"	\
 	"	mov	%" #w "[ret], %" #w "[tmp]"			\
-	: [ret] "+r" (x0), [v] "+Q" (*(unsigned long *)ptr),		\
+	: [ret] "+r" (x0), [v] "+Q" (*(u##sz *)ptr),			\
 	  [tmp] "=&r" (tmp)						\
 	: [old] "r" (x1), [new] "r" (x2)				\
 	: cl);								\
diff --git a/arch/arm64/include/asm/barrier.h b/arch/arm64/include/asm/barrier.h
index 1c5a00598458..2cfc4245d2e2 100644
--- a/arch/arm64/include/asm/barrier.h
+++ b/arch/arm64/include/asm/barrier.h
@@ -16,7 +16,11 @@
 
 #define sev()		asm volatile("sev" : : : "memory")
 #define wfe()		asm volatile("wfe" : : : "memory")
+#define wfet(val)	asm volatile("msr s0_3_c1_c0_0, %0"	\
+				     : : "r" (val) : "memory")
 #define wfi()		asm volatile("wfi" : : : "memory")
+#define wfit(val)	asm volatile("msr s0_3_c1_c0_1, %0"	\
+				     : : "r" (val) : "memory")
 
 #define isb()		asm volatile("isb" : : : "memory")
 #define dmb(opt)	asm volatile("dmb " #opt : : : "memory")
@@ -26,6 +30,14 @@
 #define __tsb_csync()	asm volatile("hint #18" : : : "memory")
 #define csdb()		asm volatile("hint #20" : : : "memory")
 
+/*
+ * Data Gathering Hint:
+ * This instruction prevents merging memory accesses with Normal-NC or
+ * Device-GRE attributes before the hint instruction with any memory accesses
+ * appearing after the hint instruction.
+ */
+#define dgh()		asm volatile("hint #6" : : : "memory")
+
 #ifdef CONFIG_ARM64_PSEUDO_NMI
 #define pmr_sync()						\
 	do {							\
@@ -38,14 +50,15 @@
 #define pmr_sync()	do {} while (0)
 #endif
 
-#define mb()		dsb(sy)
-#define rmb()		dsb(ld)
-#define wmb()		dsb(st)
+#define __mb()		dsb(sy)
+#define __rmb()		dsb(ld)
+#define __wmb()		dsb(st)
 
-#define dma_mb()	dmb(osh)
-#define dma_rmb()	dmb(oshld)
-#define dma_wmb()	dmb(oshst)
+#define __dma_mb()	dmb(osh)
+#define __dma_rmb()	dmb(oshld)
+#define __dma_wmb()	dmb(oshst)
 
+#define io_stop_wc()	dgh()
 
 #define tsb_csync()								\
 	do {									\
diff --git a/arch/arm64/include/asm/bitops.h b/arch/arm64/include/asm/bitops.h
index 81a3e519b07d..9b3c787132d2 100644
--- a/arch/arm64/include/asm/bitops.h
+++ b/arch/arm64/include/asm/bitops.h
@@ -18,7 +18,6 @@
 
 #include <asm-generic/bitops/ffz.h>
 #include <asm-generic/bitops/fls64.h>
-#include <asm-generic/bitops/find.h>
 
 #include <asm-generic/bitops/sched.h>
 #include <asm-generic/bitops/hweight.h>
diff --git a/arch/arm64/include/asm/brk-imm.h b/arch/arm64/include/asm/brk-imm.h
index ec7720dbe2c8..6e000113e508 100644
--- a/arch/arm64/include/asm/brk-imm.h
+++ b/arch/arm64/include/asm/brk-imm.h
@@ -17,6 +17,7 @@
  * 0x401: for compile time BRK instruction
  * 0x800: kernel-mode BUG() and WARN() traps
  * 0x9xx: tag-based KASAN trap (allowed values 0x900 - 0x9ff)
+ * 0x8xxx: Control-Flow Integrity traps
  */
 #define KPROBES_BRK_IMM			0x004
 #define UPROBES_BRK_IMM			0x005
@@ -28,4 +29,9 @@
 #define KASAN_BRK_IMM			0x900
 #define KASAN_BRK_MASK			0x0ff
 
+#define CFI_BRK_IMM_TARGET		GENMASK(4, 0)
+#define CFI_BRK_IMM_TYPE		GENMASK(9, 5)
+#define CFI_BRK_IMM_BASE		0x8000
+#define CFI_BRK_IMM_MASK		(CFI_BRK_IMM_TARGET | CFI_BRK_IMM_TYPE)
+
 #endif
diff --git a/arch/arm64/include/asm/cache.h b/arch/arm64/include/asm/cache.h
index a074459f8f2f..c0b178d1bb4f 100644
--- a/arch/arm64/include/asm/cache.h
+++ b/arch/arm64/include/asm/cache.h
@@ -5,33 +5,9 @@
 #ifndef __ASM_CACHE_H
 #define __ASM_CACHE_H
 
-#include <asm/cputype.h>
-
-#define CTR_L1IP_SHIFT		14
-#define CTR_L1IP_MASK		3
-#define CTR_DMINLINE_SHIFT	16
-#define CTR_IMINLINE_SHIFT	0
-#define CTR_IMINLINE_MASK	0xf
-#define CTR_ERG_SHIFT		20
-#define CTR_CWG_SHIFT		24
-#define CTR_CWG_MASK		15
-#define CTR_IDC_SHIFT		28
-#define CTR_DIC_SHIFT		29
-
-#define CTR_CACHE_MINLINE_MASK	\
-	(0xf << CTR_DMINLINE_SHIFT | CTR_IMINLINE_MASK << CTR_IMINLINE_SHIFT)
-
-#define CTR_L1IP(ctr)		(((ctr) >> CTR_L1IP_SHIFT) & CTR_L1IP_MASK)
-
-#define ICACHE_POLICY_VPIPT	0
-#define ICACHE_POLICY_RESERVED	1
-#define ICACHE_POLICY_VIPT	2
-#define ICACHE_POLICY_PIPT	3
-
 #define L1_CACHE_SHIFT		(6)
 #define L1_CACHE_BYTES		(1 << L1_CACHE_SHIFT)
 
-
 #define CLIDR_LOUU_SHIFT	27
 #define CLIDR_LOC_SHIFT		24
 #define CLIDR_LOUIS_SHIFT	21
@@ -49,15 +25,27 @@
  */
 #define ARCH_DMA_MINALIGN	(128)
 
+#ifndef __ASSEMBLY__
+
+#include <linux/bitops.h>
+#include <linux/kasan-enabled.h>
+
+#include <asm/cputype.h>
+#include <asm/mte-def.h>
+#include <asm/sysreg.h>
+
 #ifdef CONFIG_KASAN_SW_TAGS
 #define ARCH_SLAB_MINALIGN	(1ULL << KASAN_SHADOW_SCALE_SHIFT)
 #elif defined(CONFIG_KASAN_HW_TAGS)
-#define ARCH_SLAB_MINALIGN	MTE_GRANULE_SIZE
+static inline unsigned int arch_slab_minalign(void)
+{
+	return kasan_hw_tags_enabled() ? MTE_GRANULE_SIZE :
+					 __alignof__(unsigned long long);
+}
+#define arch_slab_minalign() arch_slab_minalign()
 #endif
 
-#ifndef __ASSEMBLY__
-
-#include <linux/bitops.h>
+#define CTR_L1IP(ctr)		SYS_FIELD_GET(CTR_EL0, L1Ip, ctr)
 
 #define ICACHEF_ALIASING	0
 #define ICACHEF_VPIPT		1
@@ -79,7 +67,7 @@ static __always_inline int icache_is_vpipt(void)
 
 static inline u32 cache_type_cwg(void)
 {
-	return (read_cpuid_cachetype() >> CTR_CWG_SHIFT) & CTR_CWG_MASK;
+	return SYS_FIELD_GET(CTR_EL0, CWG, read_cpuid_cachetype());
 }
 
 #define __read_mostly __section(".data..read_mostly")
@@ -113,12 +101,12 @@ static inline u32 __attribute_const__ read_cpuid_effective_cachetype(void)
 {
 	u32 ctr = read_cpuid_cachetype();
 
-	if (!(ctr & BIT(CTR_IDC_SHIFT))) {
+	if (!(ctr & BIT(CTR_EL0_IDC_SHIFT))) {
 		u64 clidr = read_sysreg(clidr_el1);
 
 		if (CLIDR_LOC(clidr) == 0 ||
 		    (CLIDR_LOUIS(clidr) == 0 && CLIDR_LOUU(clidr) == 0))
-			ctr |= BIT(CTR_IDC_SHIFT);
+			ctr |= BIT(CTR_EL0_IDC_SHIFT);
 	}
 
 	return ctr;
diff --git a/arch/arm64/include/asm/cacheflush.h b/arch/arm64/include/asm/cacheflush.h
index 5a228e203ef9..37185e978aeb 100644
--- a/arch/arm64/include/asm/cacheflush.h
+++ b/arch/arm64/include/asm/cacheflush.h
@@ -105,13 +105,6 @@ static inline void flush_icache_range(unsigned long start, unsigned long end)
 #define flush_icache_range flush_icache_range
 
 /*
- * Cache maintenance functions used by the DMA API. No to be used directly.
- */
-extern void __dma_map_area(const void *, size_t, int);
-extern void __dma_unmap_area(const void *, size_t, int);
-extern void __dma_flush_area(const void *, size_t);
-
-/*
  * Copy user data from/to a page which is mapped into a different
  * processes address space.  Really, we want to allow our "user
  * space" model to handle this.
diff --git a/arch/arm64/include/asm/cmpxchg.h b/arch/arm64/include/asm/cmpxchg.h
index f9bef42c1411..497acf134d99 100644
--- a/arch/arm64/include/asm/cmpxchg.h
+++ b/arch/arm64/include/asm/cmpxchg.h
@@ -243,7 +243,7 @@ static inline void __cmpwait_case_##sz(volatile void *ptr,		\
 	"	cbnz	%" #w "[tmp], 1f\n"				\
 	"	wfe\n"							\
 	"1:"								\
-	: [tmp] "=&r" (tmp), [v] "+Q" (*(unsigned long *)ptr)		\
+	: [tmp] "=&r" (tmp), [v] "+Q" (*(u##sz *)ptr)			\
 	: [val] "r" (val));						\
 }
 
diff --git a/arch/arm64/include/asm/compat.h b/arch/arm64/include/asm/compat.h
index eaa6ca062d89..9f362274a4f7 100644
--- a/arch/arm64/include/asm/compat.h
+++ b/arch/arm64/include/asm/compat.h
@@ -8,6 +8,15 @@
 #define compat_mode_t compat_mode_t
 typedef u16		compat_mode_t;
 
+#define __compat_uid_t	__compat_uid_t
+typedef u16		__compat_uid_t;
+typedef u16		__compat_gid_t;
+
+#define compat_ipc_pid_t compat_ipc_pid_t
+typedef u16		compat_ipc_pid_t;
+
+#define compat_statfs	compat_statfs
+
 #include <asm-generic/compat.h>
 
 #ifdef CONFIG_COMPAT
@@ -19,21 +28,15 @@ typedef u16		compat_mode_t;
 #include <linux/sched.h>
 #include <linux/sched/task_stack.h>
 
-#define COMPAT_USER_HZ		100
 #ifdef __AARCH64EB__
 #define COMPAT_UTS_MACHINE	"armv8b\0\0"
 #else
 #define COMPAT_UTS_MACHINE	"armv8l\0\0"
 #endif
 
-typedef u16		__compat_uid_t;
-typedef u16		__compat_gid_t;
 typedef u16		__compat_uid16_t;
 typedef u16		__compat_gid16_t;
-typedef u32		compat_dev_t;
 typedef s32		compat_nlink_t;
-typedef u16		compat_ipc_pid_t;
-typedef __kernel_fsid_t	compat_fsid_t;
 
 struct compat_stat {
 #ifdef __AARCH64EB__
@@ -65,26 +68,6 @@ struct compat_stat {
 	compat_ulong_t	__unused4[2];
 };
 
-struct compat_flock {
-	short		l_type;
-	short		l_whence;
-	compat_off_t	l_start;
-	compat_off_t	l_len;
-	compat_pid_t	l_pid;
-};
-
-#define F_GETLK64	12	/*  using 'struct flock64' */
-#define F_SETLK64	13
-#define F_SETLKW64	14
-
-struct compat_flock64 {
-	short		l_type;
-	short		l_whence;
-	compat_loff_t	l_start;
-	compat_loff_t	l_len;
-	compat_pid_t	l_pid;
-};
-
 struct compat_statfs {
 	int		f_type;
 	int		f_bsize;
@@ -107,64 +90,6 @@ struct compat_statfs {
 #define compat_user_stack_pointer() (user_stack_pointer(task_pt_regs(current)))
 #define COMPAT_MINSIGSTKSZ	2048
 
-struct compat_ipc64_perm {
-	compat_key_t key;
-	__compat_uid32_t uid;
-	__compat_gid32_t gid;
-	__compat_uid32_t cuid;
-	__compat_gid32_t cgid;
-	unsigned short mode;
-	unsigned short __pad1;
-	unsigned short seq;
-	unsigned short __pad2;
-	compat_ulong_t unused1;
-	compat_ulong_t unused2;
-};
-
-struct compat_semid64_ds {
-	struct compat_ipc64_perm sem_perm;
-	compat_ulong_t sem_otime;
-	compat_ulong_t sem_otime_high;
-	compat_ulong_t sem_ctime;
-	compat_ulong_t sem_ctime_high;
-	compat_ulong_t sem_nsems;
-	compat_ulong_t __unused3;
-	compat_ulong_t __unused4;
-};
-
-struct compat_msqid64_ds {
-	struct compat_ipc64_perm msg_perm;
-	compat_ulong_t msg_stime;
-	compat_ulong_t msg_stime_high;
-	compat_ulong_t msg_rtime;
-	compat_ulong_t msg_rtime_high;
-	compat_ulong_t msg_ctime;
-	compat_ulong_t msg_ctime_high;
-	compat_ulong_t msg_cbytes;
-	compat_ulong_t msg_qnum;
-	compat_ulong_t msg_qbytes;
-	compat_pid_t   msg_lspid;
-	compat_pid_t   msg_lrpid;
-	compat_ulong_t __unused4;
-	compat_ulong_t __unused5;
-};
-
-struct compat_shmid64_ds {
-	struct compat_ipc64_perm shm_perm;
-	compat_size_t  shm_segsz;
-	compat_ulong_t shm_atime;
-	compat_ulong_t shm_atime_high;
-	compat_ulong_t shm_dtime;
-	compat_ulong_t shm_dtime_high;
-	compat_ulong_t shm_ctime;
-	compat_ulong_t shm_ctime_high;
-	compat_pid_t   shm_cpid;
-	compat_pid_t   shm_lpid;
-	compat_ulong_t shm_nattch;
-	compat_ulong_t __unused4;
-	compat_ulong_t __unused5;
-};
-
 static inline int is_compat_task(void)
 {
 	return test_thread_flag(TIF_32BIT);
diff --git a/arch/arm64/include/asm/compiler.h b/arch/arm64/include/asm/compiler.h
index dc3ea4080e2e..6fb2e6bcc392 100644
--- a/arch/arm64/include/asm/compiler.h
+++ b/arch/arm64/include/asm/compiler.h
@@ -23,20 +23,4 @@
 #define __builtin_return_address(val)					\
 	(void *)(ptrauth_clear_pac((unsigned long)__builtin_return_address(val)))
 
-#ifdef CONFIG_CFI_CLANG
-/*
- * With CONFIG_CFI_CLANG, the compiler replaces function address
- * references with the address of the function's CFI jump table
- * entry. The function_nocfi macro always returns the address of the
- * actual function instead.
- */
-#define function_nocfi(x) ({						\
-	void *addr;							\
-	asm("adrp %0, " __stringify(x) "\n\t"				\
-	    "add  %0, %0, :lo12:" __stringify(x)			\
-	    : "=r" (addr));						\
-	addr;								\
-})
-#endif
-
 #endif /* __ASM_COMPILER_H */
diff --git a/arch/arm64/include/asm/cpu.h b/arch/arm64/include/asm/cpu.h
index 0f6d16faa540..fd7a92219eea 100644
--- a/arch/arm64/include/asm/cpu.h
+++ b/arch/arm64/include/asm/cpu.h
@@ -46,22 +46,28 @@ struct cpuinfo_arm64 {
 	u64		reg_midr;
 	u64		reg_revidr;
 	u64		reg_gmid;
+	u64		reg_smidr;
 
 	u64		reg_id_aa64dfr0;
 	u64		reg_id_aa64dfr1;
 	u64		reg_id_aa64isar0;
 	u64		reg_id_aa64isar1;
+	u64		reg_id_aa64isar2;
 	u64		reg_id_aa64mmfr0;
 	u64		reg_id_aa64mmfr1;
 	u64		reg_id_aa64mmfr2;
 	u64		reg_id_aa64pfr0;
 	u64		reg_id_aa64pfr1;
 	u64		reg_id_aa64zfr0;
+	u64		reg_id_aa64smfr0;
 
 	struct cpuinfo_32bit	aarch32;
 
 	/* pseudo-ZCR for recording maximum ZCR_EL1 LEN value: */
 	u64		reg_zcr;
+
+	/* pseudo-SMCR for recording maximum SMCR_EL1 LEN value: */
+	u64		reg_smcr;
 };
 
 DECLARE_PER_CPU(struct cpuinfo_arm64, cpu_data);
diff --git a/arch/arm64/include/asm/cpu_ops.h b/arch/arm64/include/asm/cpu_ops.h
index e95c4df83911..a444c8915e88 100644
--- a/arch/arm64/include/asm/cpu_ops.h
+++ b/arch/arm64/include/asm/cpu_ops.h
@@ -31,11 +31,6 @@
  * @cpu_die:	Makes a cpu leave the kernel. Must not fail. Called from the
  *		cpu being killed.
  * @cpu_kill:  Ensures a cpu has left the kernel. Called from another cpu.
- * @cpu_init_idle: Reads any data necessary to initialize CPU idle states for
- *		   a proposed logical id.
- * @cpu_suspend: Suspends a cpu and saves the required context. May fail owing
- *               to wrong parameters or error conditions. Called from the
- *               CPU being suspended. Must be called with IRQs disabled.
  */
 struct cpu_operations {
 	const char	*name;
@@ -49,10 +44,6 @@ struct cpu_operations {
 	void		(*cpu_die)(unsigned int cpu);
 	int		(*cpu_kill)(unsigned int cpu);
 #endif
-#ifdef CONFIG_CPU_IDLE
-	int		(*cpu_init_idle)(unsigned int);
-	int		(*cpu_suspend)(unsigned long);
-#endif
 };
 
 int __init init_cpu_ops(int cpu);
diff --git a/arch/arm64/include/asm/cpufeature.h b/arch/arm64/include/asm/cpufeature.h
index ef6be92b1921..f73f11b55042 100644
--- a/arch/arm64/include/asm/cpufeature.h
+++ b/arch/arm64/include/asm/cpufeature.h
@@ -6,12 +6,13 @@
 #ifndef __ASM_CPUFEATURE_H
 #define __ASM_CPUFEATURE_H
 
+#include <asm/alternative-macros.h>
 #include <asm/cpucaps.h>
 #include <asm/cputype.h>
 #include <asm/hwcap.h>
 #include <asm/sysreg.h>
 
-#define MAX_CPU_FEATURES	64
+#define MAX_CPU_FEATURES	128
 #define cpu_feature(x)		KERNEL_HWCAP_ ## x
 
 #ifndef __ASSEMBLY__
@@ -356,6 +357,7 @@ struct arm64_cpu_capabilities {
 		struct {	/* Feature register checking */
 			u32 sys_reg;
 			u8 field_pos;
+			u8 field_width;
 			u8 min_field_value;
 			u8 hwcap_type;
 			bool sign;
@@ -418,12 +420,8 @@ static __always_inline bool is_hyp_code(void)
 }
 
 extern DECLARE_BITMAP(cpu_hwcaps, ARM64_NCAPS);
-extern struct static_key_false cpu_hwcap_keys[ARM64_NCAPS];
-extern struct static_key_false arm64_const_caps_ready;
 
-/* ARM64 CAPS + alternative_cb */
-#define ARM64_NPATCHABLE (ARM64_NCAPS + 1)
-extern DECLARE_BITMAP(boot_capabilities, ARM64_NPATCHABLE);
+extern DECLARE_BITMAP(boot_capabilities, ARM64_NCAPS);
 
 #define for_each_available_cap(cap)		\
 	for_each_set_bit(cap, cpu_hwcaps, ARM64_NCAPS)
@@ -439,7 +437,7 @@ unsigned long cpu_get_elf_hwcap2(void);
 
 static __always_inline bool system_capabilities_finalized(void)
 {
-	return static_branch_likely(&arm64_const_caps_ready);
+	return alternative_has_feature_likely(ARM64_ALWAYS_SYSTEM);
 }
 
 /*
@@ -447,11 +445,11 @@ static __always_inline bool system_capabilities_finalized(void)
  *
  * Before the capability is detected, this returns false.
  */
-static inline bool cpus_have_cap(unsigned int num)
+static __always_inline bool cpus_have_cap(unsigned int num)
 {
 	if (num >= ARM64_NCAPS)
 		return false;
-	return test_bit(num, cpu_hwcaps);
+	return arch_test_bit(num, cpu_hwcaps);
 }
 
 /*
@@ -466,7 +464,7 @@ static __always_inline bool __cpus_have_const_cap(int num)
 {
 	if (num >= ARM64_NCAPS)
 		return false;
-	return static_branch_unlikely(&cpu_hwcap_keys[num]);
+	return alternative_has_feature_unlikely(num);
 }
 
 /*
@@ -552,7 +550,7 @@ cpuid_feature_cap_perfmon_field(u64 features, int field, u64 cap)
 	u64 mask = GENMASK_ULL(field + 3, field);
 
 	/* Treat IMPLEMENTATION DEFINED functionality as unimplemented */
-	if (val == ID_AA64DFR0_PMUVER_IMP_DEF)
+	if (val == ID_AA64DFR0_EL1_PMUVer_IMP_DEF)
 		val = 0;
 
 	if (val > cap) {
@@ -576,6 +574,8 @@ static inline u64 arm64_ftr_reg_user_value(const struct arm64_ftr_reg *reg)
 static inline int __attribute_const__
 cpuid_feature_extract_field_width(u64 features, int field, int width, bool sign)
 {
+	if (WARN_ON_ONCE(!width))
+		width = 4;
 	return (sign) ?
 		cpuid_feature_extract_signed_field_width(features, field, width) :
 		cpuid_feature_extract_unsigned_field_width(features, field, width);
@@ -594,36 +594,43 @@ static inline s64 arm64_ftr_value(const struct arm64_ftr_bits *ftrp, u64 val)
 
 static inline bool id_aa64mmfr0_mixed_endian_el0(u64 mmfr0)
 {
-	return cpuid_feature_extract_unsigned_field(mmfr0, ID_AA64MMFR0_BIGENDEL_SHIFT) == 0x1 ||
-		cpuid_feature_extract_unsigned_field(mmfr0, ID_AA64MMFR0_BIGENDEL0_SHIFT) == 0x1;
+	return cpuid_feature_extract_unsigned_field(mmfr0, ID_AA64MMFR0_EL1_BIGEND_SHIFT) == 0x1 ||
+		cpuid_feature_extract_unsigned_field(mmfr0, ID_AA64MMFR0_EL1_BIGENDEL0_SHIFT) == 0x1;
 }
 
 static inline bool id_aa64pfr0_32bit_el1(u64 pfr0)
 {
-	u32 val = cpuid_feature_extract_unsigned_field(pfr0, ID_AA64PFR0_EL1_SHIFT);
+	u32 val = cpuid_feature_extract_unsigned_field(pfr0, ID_AA64PFR0_EL1_EL1_SHIFT);
 
-	return val == ID_AA64PFR0_ELx_32BIT_64BIT;
+	return val == ID_AA64PFR0_EL1_ELx_32BIT_64BIT;
 }
 
 static inline bool id_aa64pfr0_32bit_el0(u64 pfr0)
 {
-	u32 val = cpuid_feature_extract_unsigned_field(pfr0, ID_AA64PFR0_EL0_SHIFT);
+	u32 val = cpuid_feature_extract_unsigned_field(pfr0, ID_AA64PFR0_EL1_EL0_SHIFT);
 
-	return val == ID_AA64PFR0_ELx_32BIT_64BIT;
+	return val == ID_AA64PFR0_EL1_ELx_32BIT_64BIT;
 }
 
 static inline bool id_aa64pfr0_sve(u64 pfr0)
 {
-	u32 val = cpuid_feature_extract_unsigned_field(pfr0, ID_AA64PFR0_SVE_SHIFT);
+	u32 val = cpuid_feature_extract_unsigned_field(pfr0, ID_AA64PFR0_EL1_SVE_SHIFT);
+
+	return val > 0;
+}
+
+static inline bool id_aa64pfr1_sme(u64 pfr1)
+{
+	u32 val = cpuid_feature_extract_unsigned_field(pfr1, ID_AA64PFR1_EL1_SME_SHIFT);
 
 	return val > 0;
 }
 
 static inline bool id_aa64pfr1_mte(u64 pfr1)
 {
-	u32 val = cpuid_feature_extract_unsigned_field(pfr1, ID_AA64PFR1_MTE_SHIFT);
+	u32 val = cpuid_feature_extract_unsigned_field(pfr1, ID_AA64PFR1_EL1_MTE_SHIFT);
 
-	return val >= ID_AA64PFR1_MTE;
+	return val >= ID_AA64PFR1_EL1_MTE_MTE2;
 }
 
 void __init setup_cpu_features(void);
@@ -637,6 +644,35 @@ static inline bool cpu_supports_mixed_endian_el0(void)
 	return id_aa64mmfr0_mixed_endian_el0(read_cpuid(ID_AA64MMFR0_EL1));
 }
 
+
+static inline bool supports_csv2p3(int scope)
+{
+	u64 pfr0;
+	u8 csv2_val;
+
+	if (scope == SCOPE_LOCAL_CPU)
+		pfr0 = read_sysreg_s(SYS_ID_AA64PFR0_EL1);
+	else
+		pfr0 = read_sanitised_ftr_reg(SYS_ID_AA64PFR0_EL1);
+
+	csv2_val = cpuid_feature_extract_unsigned_field(pfr0,
+							ID_AA64PFR0_EL1_CSV2_SHIFT);
+	return csv2_val == 3;
+}
+
+static inline bool supports_clearbhb(int scope)
+{
+	u64 isar2;
+
+	if (scope == SCOPE_LOCAL_CPU)
+		isar2 = read_sysreg_s(SYS_ID_AA64ISAR2_EL1);
+	else
+		isar2 = read_sanitised_ftr_reg(SYS_ID_AA64ISAR2_EL1);
+
+	return cpuid_feature_extract_unsigned_field(isar2,
+						    ID_AA64ISAR2_EL1_BC_SHIFT);
+}
+
 const struct cpumask *system_32bit_el0_cpumask(void);
 DECLARE_STATIC_KEY_FALSE(arm64_mismatched_32bit_el0);
 
@@ -655,10 +691,10 @@ static inline bool system_supports_4kb_granule(void)
 
 	mmfr0 =	read_sanitised_ftr_reg(SYS_ID_AA64MMFR0_EL1);
 	val = cpuid_feature_extract_unsigned_field(mmfr0,
-						ID_AA64MMFR0_TGRAN4_SHIFT);
+						ID_AA64MMFR0_EL1_TGRAN4_SHIFT);
 
-	return (val >= ID_AA64MMFR0_TGRAN4_SUPPORTED_MIN) &&
-	       (val <= ID_AA64MMFR0_TGRAN4_SUPPORTED_MAX);
+	return (val >= ID_AA64MMFR0_EL1_TGRAN4_SUPPORTED_MIN) &&
+	       (val <= ID_AA64MMFR0_EL1_TGRAN4_SUPPORTED_MAX);
 }
 
 static inline bool system_supports_64kb_granule(void)
@@ -668,10 +704,10 @@ static inline bool system_supports_64kb_granule(void)
 
 	mmfr0 =	read_sanitised_ftr_reg(SYS_ID_AA64MMFR0_EL1);
 	val = cpuid_feature_extract_unsigned_field(mmfr0,
-						ID_AA64MMFR0_TGRAN64_SHIFT);
+						ID_AA64MMFR0_EL1_TGRAN64_SHIFT);
 
-	return (val >= ID_AA64MMFR0_TGRAN64_SUPPORTED_MIN) &&
-	       (val <= ID_AA64MMFR0_TGRAN64_SUPPORTED_MAX);
+	return (val >= ID_AA64MMFR0_EL1_TGRAN64_SUPPORTED_MIN) &&
+	       (val <= ID_AA64MMFR0_EL1_TGRAN64_SUPPORTED_MAX);
 }
 
 static inline bool system_supports_16kb_granule(void)
@@ -681,10 +717,10 @@ static inline bool system_supports_16kb_granule(void)
 
 	mmfr0 =	read_sanitised_ftr_reg(SYS_ID_AA64MMFR0_EL1);
 	val = cpuid_feature_extract_unsigned_field(mmfr0,
-						ID_AA64MMFR0_TGRAN16_SHIFT);
+						ID_AA64MMFR0_EL1_TGRAN16_SHIFT);
 
-	return (val >= ID_AA64MMFR0_TGRAN16_SUPPORTED_MIN) &&
-	       (val <= ID_AA64MMFR0_TGRAN16_SUPPORTED_MAX);
+	return (val >= ID_AA64MMFR0_EL1_TGRAN16_SUPPORTED_MIN) &&
+	       (val <= ID_AA64MMFR0_EL1_TGRAN16_SUPPORTED_MAX);
 }
 
 static inline bool system_supports_mixed_endian_el0(void)
@@ -699,7 +735,7 @@ static inline bool system_supports_mixed_endian(void)
 
 	mmfr0 =	read_sanitised_ftr_reg(SYS_ID_AA64MMFR0_EL1);
 	val = cpuid_feature_extract_unsigned_field(mmfr0,
-						ID_AA64MMFR0_BIGENDEL_SHIFT);
+						ID_AA64MMFR0_EL1_BIGEND_SHIFT);
 
 	return val == 0x1;
 }
@@ -727,6 +763,23 @@ static __always_inline bool system_supports_sve(void)
 		cpus_have_const_cap(ARM64_SVE);
 }
 
+static __always_inline bool system_supports_sme(void)
+{
+	return IS_ENABLED(CONFIG_ARM64_SME) &&
+		cpus_have_const_cap(ARM64_SME);
+}
+
+static __always_inline bool system_supports_fa64(void)
+{
+	return IS_ENABLED(CONFIG_ARM64_SME) &&
+		cpus_have_const_cap(ARM64_SME_FA64);
+}
+
+static __always_inline bool system_supports_tpidr2(void)
+{
+	return system_supports_sme();
+}
+
 static __always_inline bool system_supports_cnp(void)
 {
 	return IS_ENABLED(CONFIG_ARM64_CNP) &&
@@ -784,13 +837,13 @@ extern int do_emulate_mrs(struct pt_regs *regs, u32 sys_reg, u32 rt);
 static inline u32 id_aa64mmfr0_parange_to_phys_shift(int parange)
 {
 	switch (parange) {
-	case ID_AA64MMFR0_PARANGE_32: return 32;
-	case ID_AA64MMFR0_PARANGE_36: return 36;
-	case ID_AA64MMFR0_PARANGE_40: return 40;
-	case ID_AA64MMFR0_PARANGE_42: return 42;
-	case ID_AA64MMFR0_PARANGE_44: return 44;
-	case ID_AA64MMFR0_PARANGE_48: return 48;
-	case ID_AA64MMFR0_PARANGE_52: return 52;
+	case ID_AA64MMFR0_EL1_PARANGE_32: return 32;
+	case ID_AA64MMFR0_EL1_PARANGE_36: return 36;
+	case ID_AA64MMFR0_EL1_PARANGE_40: return 40;
+	case ID_AA64MMFR0_EL1_PARANGE_42: return 42;
+	case ID_AA64MMFR0_EL1_PARANGE_44: return 44;
+	case ID_AA64MMFR0_EL1_PARANGE_48: return 48;
+	case ID_AA64MMFR0_EL1_PARANGE_52: return 52;
 	/*
 	 * A future PE could use a value unknown to the kernel.
 	 * However, by the "D10.1.4 Principles of the ID scheme
@@ -812,14 +865,14 @@ static inline bool cpu_has_hw_af(void)
 
 	mmfr1 = read_cpuid(ID_AA64MMFR1_EL1);
 	return cpuid_feature_extract_unsigned_field(mmfr1,
-						ID_AA64MMFR1_HADBS_SHIFT);
+						ID_AA64MMFR1_EL1_HAFDBS_SHIFT);
 }
 
 static inline bool cpu_has_pan(void)
 {
 	u64 mmfr1 = read_cpuid(ID_AA64MMFR1_EL1);
 	return cpuid_feature_extract_unsigned_field(mmfr1,
-						    ID_AA64MMFR1_PAN_SHIFT);
+						    ID_AA64MMFR1_EL1_PAN_SHIFT);
 }
 
 #ifdef CONFIG_ARM64_AMU_EXTN
@@ -840,8 +893,8 @@ static inline unsigned int get_vmid_bits(u64 mmfr1)
 	int vmid_bits;
 
 	vmid_bits = cpuid_feature_extract_unsigned_field(mmfr1,
-						ID_AA64MMFR1_VMIDBITS_SHIFT);
-	if (vmid_bits == ID_AA64MMFR1_VMIDBITS_16)
+						ID_AA64MMFR1_EL1_VMIDBits_SHIFT);
+	if (vmid_bits == ID_AA64MMFR1_EL1_VMIDBits_16)
 		return 16;
 
 	/*
@@ -851,9 +904,15 @@ static inline unsigned int get_vmid_bits(u64 mmfr1)
 	return 8;
 }
 
+struct arm64_ftr_reg *get_arm64_ftr_reg(u32 sys_id);
+
 extern struct arm64_ftr_override id_aa64mmfr1_override;
+extern struct arm64_ftr_override id_aa64pfr0_override;
 extern struct arm64_ftr_override id_aa64pfr1_override;
+extern struct arm64_ftr_override id_aa64zfr0_override;
+extern struct arm64_ftr_override id_aa64smfr0_override;
 extern struct arm64_ftr_override id_aa64isar1_override;
+extern struct arm64_ftr_override id_aa64isar2_override;
 
 u32 get_kvm_ipa_limit(void);
 void dump_cpu_features(void);
diff --git a/arch/arm64/include/asm/cpuidle.h b/arch/arm64/include/asm/cpuidle.h
index 14a19d1141bd..2047713e097d 100644
--- a/arch/arm64/include/asm/cpuidle.h
+++ b/arch/arm64/include/asm/cpuidle.h
@@ -4,21 +4,6 @@
 
 #include <asm/proc-fns.h>
 
-#ifdef CONFIG_CPU_IDLE
-extern int arm_cpuidle_init(unsigned int cpu);
-extern int arm_cpuidle_suspend(int index);
-#else
-static inline int arm_cpuidle_init(unsigned int cpu)
-{
-	return -EOPNOTSUPP;
-}
-
-static inline int arm_cpuidle_suspend(int index)
-{
-	return -EOPNOTSUPP;
-}
-#endif
-
 #ifdef CONFIG_ARM64_PSEUDO_NMI
 #include <asm/arch_gicv3.h>
 
diff --git a/arch/arm64/include/asm/cputype.h b/arch/arm64/include/asm/cputype.h
index 19b8441aa8f2..65e53ef5a396 100644
--- a/arch/arm64/include/asm/cputype.h
+++ b/arch/arm64/include/asm/cputype.h
@@ -36,12 +36,12 @@
 #define MIDR_VARIANT(midr)	\
 	(((midr) & MIDR_VARIANT_MASK) >> MIDR_VARIANT_SHIFT)
 #define MIDR_IMPLEMENTOR_SHIFT	24
-#define MIDR_IMPLEMENTOR_MASK	(0xff << MIDR_IMPLEMENTOR_SHIFT)
+#define MIDR_IMPLEMENTOR_MASK	(0xffU << MIDR_IMPLEMENTOR_SHIFT)
 #define MIDR_IMPLEMENTOR(midr)	\
 	(((midr) & MIDR_IMPLEMENTOR_MASK) >> MIDR_IMPLEMENTOR_SHIFT)
 
 #define MIDR_CPU_MODEL(imp, partnum) \
-	(((imp)			<< MIDR_IMPLEMENTOR_SHIFT) | \
+	((_AT(u32, imp)		<< MIDR_IMPLEMENTOR_SHIFT) | \
 	(0xf			<< MIDR_ARCHITECTURE_SHIFT) | \
 	((partnum)		<< MIDR_PARTNUM_SHIFT))
 
@@ -60,6 +60,7 @@
 #define ARM_CPU_IMP_FUJITSU		0x46
 #define ARM_CPU_IMP_HISI		0x48
 #define ARM_CPU_IMP_APPLE		0x61
+#define ARM_CPU_IMP_AMPERE		0xC0
 
 #define ARM_CPU_PART_AEM_V8		0xD0F
 #define ARM_CPU_PART_FOUNDATION		0xD00
@@ -73,8 +74,15 @@
 #define ARM_CPU_PART_CORTEX_A76		0xD0B
 #define ARM_CPU_PART_NEOVERSE_N1	0xD0C
 #define ARM_CPU_PART_CORTEX_A77		0xD0D
+#define ARM_CPU_PART_NEOVERSE_V1	0xD40
+#define ARM_CPU_PART_CORTEX_A78		0xD41
+#define ARM_CPU_PART_CORTEX_A78AE	0xD42
+#define ARM_CPU_PART_CORTEX_X1		0xD44
+#define ARM_CPU_PART_CORTEX_A510	0xD46
 #define ARM_CPU_PART_CORTEX_A710	0xD47
+#define ARM_CPU_PART_CORTEX_X2		0xD48
 #define ARM_CPU_PART_NEOVERSE_N2	0xD49
+#define ARM_CPU_PART_CORTEX_A78C	0xD4B
 
 #define APM_CPU_PART_POTENZA		0x000
 
@@ -82,6 +90,13 @@
 #define CAVIUM_CPU_PART_THUNDERX_81XX	0x0A2
 #define CAVIUM_CPU_PART_THUNDERX_83XX	0x0A3
 #define CAVIUM_CPU_PART_THUNDERX2	0x0AF
+/* OcteonTx2 series */
+#define CAVIUM_CPU_PART_OCTX2_98XX	0x0B1
+#define CAVIUM_CPU_PART_OCTX2_96XX	0x0B2
+#define CAVIUM_CPU_PART_OCTX2_95XX	0x0B3
+#define CAVIUM_CPU_PART_OCTX2_95XXN	0x0B4
+#define CAVIUM_CPU_PART_OCTX2_95XXMM	0x0B5
+#define CAVIUM_CPU_PART_OCTX2_95XXO	0x0B6
 
 #define BRCM_CPU_PART_BRAHMA_B53	0x100
 #define BRCM_CPU_PART_VULCAN		0x516
@@ -104,6 +119,12 @@
 
 #define APPLE_CPU_PART_M1_ICESTORM	0x022
 #define APPLE_CPU_PART_M1_FIRESTORM	0x023
+#define APPLE_CPU_PART_M1_ICESTORM_PRO	0x024
+#define APPLE_CPU_PART_M1_FIRESTORM_PRO	0x025
+#define APPLE_CPU_PART_M1_ICESTORM_MAX	0x028
+#define APPLE_CPU_PART_M1_FIRESTORM_MAX	0x029
+
+#define AMPERE_CPU_PART_AMPERE1		0xAC3
 
 #define MIDR_CORTEX_A53 MIDR_CPU_MODEL(ARM_CPU_IMP_ARM, ARM_CPU_PART_CORTEX_A53)
 #define MIDR_CORTEX_A57 MIDR_CPU_MODEL(ARM_CPU_IMP_ARM, ARM_CPU_PART_CORTEX_A57)
@@ -115,11 +136,24 @@
 #define MIDR_CORTEX_A76	MIDR_CPU_MODEL(ARM_CPU_IMP_ARM, ARM_CPU_PART_CORTEX_A76)
 #define MIDR_NEOVERSE_N1 MIDR_CPU_MODEL(ARM_CPU_IMP_ARM, ARM_CPU_PART_NEOVERSE_N1)
 #define MIDR_CORTEX_A77	MIDR_CPU_MODEL(ARM_CPU_IMP_ARM, ARM_CPU_PART_CORTEX_A77)
+#define MIDR_NEOVERSE_V1	MIDR_CPU_MODEL(ARM_CPU_IMP_ARM, ARM_CPU_PART_NEOVERSE_V1)
+#define MIDR_CORTEX_A78	MIDR_CPU_MODEL(ARM_CPU_IMP_ARM, ARM_CPU_PART_CORTEX_A78)
+#define MIDR_CORTEX_A78AE	MIDR_CPU_MODEL(ARM_CPU_IMP_ARM, ARM_CPU_PART_CORTEX_A78AE)
+#define MIDR_CORTEX_X1	MIDR_CPU_MODEL(ARM_CPU_IMP_ARM, ARM_CPU_PART_CORTEX_X1)
+#define MIDR_CORTEX_A510 MIDR_CPU_MODEL(ARM_CPU_IMP_ARM, ARM_CPU_PART_CORTEX_A510)
 #define MIDR_CORTEX_A710 MIDR_CPU_MODEL(ARM_CPU_IMP_ARM, ARM_CPU_PART_CORTEX_A710)
+#define MIDR_CORTEX_X2 MIDR_CPU_MODEL(ARM_CPU_IMP_ARM, ARM_CPU_PART_CORTEX_X2)
 #define MIDR_NEOVERSE_N2 MIDR_CPU_MODEL(ARM_CPU_IMP_ARM, ARM_CPU_PART_NEOVERSE_N2)
+#define MIDR_CORTEX_A78C	MIDR_CPU_MODEL(ARM_CPU_IMP_ARM, ARM_CPU_PART_CORTEX_A78C)
 #define MIDR_THUNDERX	MIDR_CPU_MODEL(ARM_CPU_IMP_CAVIUM, CAVIUM_CPU_PART_THUNDERX)
 #define MIDR_THUNDERX_81XX MIDR_CPU_MODEL(ARM_CPU_IMP_CAVIUM, CAVIUM_CPU_PART_THUNDERX_81XX)
 #define MIDR_THUNDERX_83XX MIDR_CPU_MODEL(ARM_CPU_IMP_CAVIUM, CAVIUM_CPU_PART_THUNDERX_83XX)
+#define MIDR_OCTX2_98XX MIDR_CPU_MODEL(ARM_CPU_IMP_CAVIUM, CAVIUM_CPU_PART_OCTX2_98XX)
+#define MIDR_OCTX2_96XX MIDR_CPU_MODEL(ARM_CPU_IMP_CAVIUM, CAVIUM_CPU_PART_OCTX2_96XX)
+#define MIDR_OCTX2_95XX MIDR_CPU_MODEL(ARM_CPU_IMP_CAVIUM, CAVIUM_CPU_PART_OCTX2_95XX)
+#define MIDR_OCTX2_95XXN MIDR_CPU_MODEL(ARM_CPU_IMP_CAVIUM, CAVIUM_CPU_PART_OCTX2_95XXN)
+#define MIDR_OCTX2_95XXMM MIDR_CPU_MODEL(ARM_CPU_IMP_CAVIUM, CAVIUM_CPU_PART_OCTX2_95XXMM)
+#define MIDR_OCTX2_95XXO MIDR_CPU_MODEL(ARM_CPU_IMP_CAVIUM, CAVIUM_CPU_PART_OCTX2_95XXO)
 #define MIDR_CAVIUM_THUNDERX2 MIDR_CPU_MODEL(ARM_CPU_IMP_CAVIUM, CAVIUM_CPU_PART_THUNDERX2)
 #define MIDR_BRAHMA_B53 MIDR_CPU_MODEL(ARM_CPU_IMP_BRCM, BRCM_CPU_PART_BRAHMA_B53)
 #define MIDR_BRCM_VULCAN MIDR_CPU_MODEL(ARM_CPU_IMP_BRCM, BRCM_CPU_PART_VULCAN)
@@ -137,6 +171,11 @@
 #define MIDR_HISI_TSV110 MIDR_CPU_MODEL(ARM_CPU_IMP_HISI, HISI_CPU_PART_TSV110)
 #define MIDR_APPLE_M1_ICESTORM MIDR_CPU_MODEL(ARM_CPU_IMP_APPLE, APPLE_CPU_PART_M1_ICESTORM)
 #define MIDR_APPLE_M1_FIRESTORM MIDR_CPU_MODEL(ARM_CPU_IMP_APPLE, APPLE_CPU_PART_M1_FIRESTORM)
+#define MIDR_APPLE_M1_ICESTORM_PRO MIDR_CPU_MODEL(ARM_CPU_IMP_APPLE, APPLE_CPU_PART_M1_ICESTORM_PRO)
+#define MIDR_APPLE_M1_FIRESTORM_PRO MIDR_CPU_MODEL(ARM_CPU_IMP_APPLE, APPLE_CPU_PART_M1_FIRESTORM_PRO)
+#define MIDR_APPLE_M1_ICESTORM_MAX MIDR_CPU_MODEL(ARM_CPU_IMP_APPLE, APPLE_CPU_PART_M1_ICESTORM_MAX)
+#define MIDR_APPLE_M1_FIRESTORM_MAX MIDR_CPU_MODEL(ARM_CPU_IMP_APPLE, APPLE_CPU_PART_M1_FIRESTORM_MAX)
+#define MIDR_AMPERE1 MIDR_CPU_MODEL(ARM_CPU_IMP_AMPERE, AMPERE_CPU_PART_AMPERE1)
 
 /* Fujitsu Erratum 010001 affects A64FX 1.0 and 1.1, (v0r0 and v1r0) */
 #define MIDR_FUJITSU_ERRATUM_010001		MIDR_FUJITSU_A64FX
diff --git a/arch/arm64/include/asm/debug-monitors.h b/arch/arm64/include/asm/debug-monitors.h
index 657c921fd784..7b7e05c02691 100644
--- a/arch/arm64/include/asm/debug-monitors.h
+++ b/arch/arm64/include/asm/debug-monitors.h
@@ -34,18 +34,6 @@
  */
 #define BREAK_INSTR_SIZE		AARCH64_INSN_SIZE
 
-/*
- * BRK instruction encoding
- * The #imm16 value should be placed at bits[20:5] within BRK ins
- */
-#define AARCH64_BREAK_MON	0xd4200000
-
-/*
- * BRK instruction for provoking a fault on purpose
- * Unlike kgdb, #imm16 value with unallocated handler is used for faulting.
- */
-#define AARCH64_BREAK_FAULT	(AARCH64_BREAK_MON | (FAULT_BRK_IMM << 5))
-
 #define AARCH64_BREAK_KGDB_DYN_DBG	\
 	(AARCH64_BREAK_MON | (KGDB_DYN_DBG_BRK_IMM << 5))
 
@@ -76,7 +64,7 @@ struct task_struct;
 
 struct step_hook {
 	struct list_head node;
-	int (*fn)(struct pt_regs *regs, unsigned int esr);
+	int (*fn)(struct pt_regs *regs, unsigned long esr);
 };
 
 void register_user_step_hook(struct step_hook *hook);
@@ -87,7 +75,7 @@ void unregister_kernel_step_hook(struct step_hook *hook);
 
 struct break_hook {
 	struct list_head node;
-	int (*fn)(struct pt_regs *regs, unsigned int esr);
+	int (*fn)(struct pt_regs *regs, unsigned long esr);
 	u16 imm;
 	u16 mask; /* These bits are ignored when comparing with imm */
 };
diff --git a/arch/arm64/include/asm/efi.h b/arch/arm64/include/asm/efi.h
index d3e1825337be..d6cf535d8352 100644
--- a/arch/arm64/include/asm/efi.h
+++ b/arch/arm64/include/asm/efi.h
@@ -14,9 +14,16 @@
 
 #ifdef CONFIG_EFI
 extern void efi_init(void);
-extern void efifb_setup_from_dmi(struct screen_info *si, const char *opt);
+
+bool efi_runtime_fixup_exception(struct pt_regs *regs, const char *msg);
 #else
 #define efi_init()
+
+static inline
+bool efi_runtime_fixup_exception(struct pt_regs *regs, const char *msg)
+{
+	return false;
+}
 #endif
 
 int efi_create_mapping(struct mm_struct *mm, efi_memory_desc_t *md);
@@ -28,12 +35,9 @@ int efi_set_mapping_permissions(struct mm_struct *mm, efi_memory_desc_t *md);
 	__efi_fpsimd_begin();						\
 })
 
+#undef arch_efi_call_virt
 #define arch_efi_call_virt(p, f, args...)				\
-({									\
-	efi_##f##_t *__f;						\
-	__f = p->f;							\
-	__efi_rt_asm_wrapper(__f, #f, args);				\
-})
+	__efi_rt_asm_wrapper((p)->f, #f, args)
 
 #define arch_efi_call_virt_teardown()					\
 ({									\
diff --git a/arch/arm64/include/asm/el2_setup.h b/arch/arm64/include/asm/el2_setup.h
index 3198acb2aad8..668569adf4d3 100644
--- a/arch/arm64/include/asm/el2_setup.h
+++ b/arch/arm64/include/asm/el2_setup.h
@@ -40,7 +40,7 @@
 
 .macro __init_el2_debug
 	mrs	x1, id_aa64dfr0_el1
-	sbfx	x0, x1, #ID_AA64DFR0_PMUVER_SHIFT, #4
+	sbfx	x0, x1, #ID_AA64DFR0_EL1_PMUVer_SHIFT, #4
 	cmp	x0, #1
 	b.lt	.Lskip_pmu_\@			// Skip if no PMU present
 	mrs	x0, pmcr_el0			// Disable debug access traps
@@ -49,7 +49,7 @@
 	csel	x2, xzr, x0, lt			// all PMU counters from EL1
 
 	/* Statistical profiling */
-	ubfx	x0, x1, #ID_AA64DFR0_PMSVER_SHIFT, #4
+	ubfx	x0, x1, #ID_AA64DFR0_EL1_PMSVer_SHIFT, #4
 	cbz	x0, .Lskip_spe_\@		// Skip if SPE not present
 
 	mrs_s	x0, SYS_PMBIDR_EL1              // If SPE available at EL2,
@@ -65,7 +65,7 @@
 
 .Lskip_spe_\@:
 	/* Trace buffer */
-	ubfx	x0, x1, #ID_AA64DFR0_TRBE_SHIFT, #4
+	ubfx	x0, x1, #ID_AA64DFR0_EL1_TraceBuffer_SHIFT, #4
 	cbz	x0, .Lskip_trace_\@		// Skip if TraceBuffer is not present
 
 	mrs_s	x0, SYS_TRBIDR_EL1
@@ -83,7 +83,7 @@
 /* LORegions */
 .macro __init_el2_lor
 	mrs	x1, id_aa64mmfr1_el1
-	ubfx	x0, x1, #ID_AA64MMFR1_LOR_SHIFT, 4
+	ubfx	x0, x1, #ID_AA64MMFR1_EL1_LO_SHIFT, 4
 	cbz	x0, .Lskip_lor_\@
 	msr_s	SYS_LORC_EL1, xzr
 .Lskip_lor_\@:
@@ -97,7 +97,7 @@
 /* GICv3 system register access */
 .macro __init_el2_gicv3
 	mrs	x0, id_aa64pfr0_el1
-	ubfx	x0, x0, #ID_AA64PFR0_GIC_SHIFT, #4
+	ubfx	x0, x0, #ID_AA64PFR0_EL1_GIC_SHIFT, #4
 	cbz	x0, .Lskip_gicv3_\@
 
 	mrs_s	x0, SYS_ICC_SRE_EL2
@@ -106,8 +106,8 @@
 	msr_s	SYS_ICC_SRE_EL2, x0
 	isb					// Make sure SRE is now set
 	mrs_s	x0, SYS_ICC_SRE_EL2		// Read SRE back,
-	tbz	x0, #0, 1f			// and check that it sticks
-	msr_s	SYS_ICH_HCR_EL2, xzr		// Reset ICC_HCR_EL2 to defaults
+	tbz	x0, #0, .Lskip_gicv3_\@		// and check that it sticks
+	msr_s	SYS_ICH_HCR_EL2, xzr		// Reset ICH_HCR_EL2 to defaults
 .Lskip_gicv3_\@:
 .endm
 
@@ -129,43 +129,40 @@
 	msr	cptr_el2, x0			// Disable copro. traps to EL2
 .endm
 
-/* SVE register access */
-.macro __init_el2_nvhe_sve
-	mrs	x1, id_aa64pfr0_el1
-	ubfx	x1, x1, #ID_AA64PFR0_SVE_SHIFT, #4
-	cbz	x1, .Lskip_sve_\@
-
-	bic	x0, x0, #CPTR_EL2_TZ		// Also disable SVE traps
-	msr	cptr_el2, x0			// Disable copro. traps to EL2
-	isb
-	mov	x1, #ZCR_ELx_LEN_MASK		// SVE: Enable full vector
-	msr_s	SYS_ZCR_EL2, x1			// length for EL1.
-.Lskip_sve_\@:
-.endm
-
 /* Disable any fine grained traps */
 .macro __init_el2_fgt
 	mrs	x1, id_aa64mmfr0_el1
-	ubfx	x1, x1, #ID_AA64MMFR0_FGT_SHIFT, #4
+	ubfx	x1, x1, #ID_AA64MMFR0_EL1_FGT_SHIFT, #4
 	cbz	x1, .Lskip_fgt_\@
 
 	mov	x0, xzr
 	mrs	x1, id_aa64dfr0_el1
-	ubfx	x1, x1, #ID_AA64DFR0_PMSVER_SHIFT, #4
+	ubfx	x1, x1, #ID_AA64DFR0_EL1_PMSVer_SHIFT, #4
 	cmp	x1, #3
-	b.lt	.Lset_fgt_\@
+	b.lt	.Lset_debug_fgt_\@
 	/* Disable PMSNEVFR_EL1 read and write traps */
 	orr	x0, x0, #(1 << 62)
 
-.Lset_fgt_\@:
+.Lset_debug_fgt_\@:
 	msr_s	SYS_HDFGRTR_EL2, x0
 	msr_s	SYS_HDFGWTR_EL2, x0
-	msr_s	SYS_HFGRTR_EL2, xzr
-	msr_s	SYS_HFGWTR_EL2, xzr
+
+	mov	x0, xzr
+	mrs	x1, id_aa64pfr1_el1
+	ubfx	x1, x1, #ID_AA64PFR1_EL1_SME_SHIFT, #4
+	cbz	x1, .Lset_fgt_\@
+
+	/* Disable nVHE traps of TPIDR2 and SMPRI */
+	orr	x0, x0, #HFGxTR_EL2_nSMPRI_EL1_MASK
+	orr	x0, x0, #HFGxTR_EL2_nTPIDR2_EL0_MASK
+
+.Lset_fgt_\@:
+	msr_s	SYS_HFGRTR_EL2, x0
+	msr_s	SYS_HFGWTR_EL2, x0
 	msr_s	SYS_HFGITR_EL2, xzr
 
 	mrs	x1, id_aa64pfr0_el1		// AMU traps UNDEF without AMU
-	ubfx	x1, x1, #ID_AA64PFR0_AMU_SHIFT, #4
+	ubfx	x1, x1, #ID_AA64PFR0_EL1_AMU_SHIFT, #4
 	cbz	x1, .Lskip_fgt_\@
 
 	msr_s	SYS_HAFGRTR_EL2, xzr
@@ -195,7 +192,6 @@
 	__init_el2_hstr
 	__init_el2_nvhe_idregs
 	__init_el2_nvhe_cptr
-	__init_el2_nvhe_sve
 	__init_el2_fgt
 	__init_el2_nvhe_prepare_eret
 .endm
diff --git a/arch/arm64/include/asm/esr.h b/arch/arm64/include/asm/esr.h
index d52a0b269ee8..15b34fbfca66 100644
--- a/arch/arm64/include/asm/esr.h
+++ b/arch/arm64/include/asm/esr.h
@@ -37,7 +37,8 @@
 #define ESR_ELx_EC_ERET		(0x1a)	/* EL2 only */
 /* Unallocated EC: 0x1B */
 #define ESR_ELx_EC_FPAC		(0x1C)	/* EL1 and above */
-/* Unallocated EC: 0x1D - 0x1E */
+#define ESR_ELx_EC_SME		(0x1D)
+/* Unallocated EC: 0x1E */
 #define ESR_ELx_EC_IMP_DEF	(0x1f)	/* EL3 only */
 #define ESR_ELx_EC_IABT_LOW	(0x20)
 #define ESR_ELx_EC_IABT_CUR	(0x21)
@@ -75,6 +76,7 @@
 #define ESR_ELx_IL_SHIFT	(25)
 #define ESR_ELx_IL		(UL(1) << ESR_ELx_IL_SHIFT)
 #define ESR_ELx_ISS_MASK	(ESR_ELx_IL - 1)
+#define ESR_ELx_ISS(esr)	((esr) & ESR_ELx_ISS_MASK)
 
 /* ISS field definitions shared by different classes */
 #define ESR_ELx_WNR_SHIFT	(6)
@@ -133,10 +135,13 @@
 #define ESR_ELx_CV		(UL(1) << 24)
 #define ESR_ELx_COND_SHIFT	(20)
 #define ESR_ELx_COND_MASK	(UL(0xF) << ESR_ELx_COND_SHIFT)
-#define ESR_ELx_WFx_ISS_TI	(UL(1) << 0)
+#define ESR_ELx_WFx_ISS_RN	(UL(0x1F) << 5)
+#define ESR_ELx_WFx_ISS_RV	(UL(1) << 2)
+#define ESR_ELx_WFx_ISS_TI	(UL(3) << 0)
+#define ESR_ELx_WFx_ISS_WFxT	(UL(2) << 0)
 #define ESR_ELx_WFx_ISS_WFI	(UL(0) << 0)
 #define ESR_ELx_WFx_ISS_WFE	(UL(1) << 0)
-#define ESR_ELx_xVC_IMM_MASK	((1UL << 16) - 1)
+#define ESR_ELx_xVC_IMM_MASK	((UL(1) << 16) - 1)
 
 #define DISR_EL1_IDS		(UL(1) << 24)
 /*
@@ -146,7 +151,8 @@
 #define DISR_EL1_ESR_MASK	(ESR_ELx_AET | ESR_ELx_EA | ESR_ELx_FSC)
 
 /* ESR value templates for specific events */
-#define ESR_ELx_WFx_MASK	(ESR_ELx_EC_MASK | ESR_ELx_WFx_ISS_TI)
+#define ESR_ELx_WFx_MASK	(ESR_ELx_EC_MASK |			\
+				 (ESR_ELx_WFx_ISS_TI & ~ESR_ELx_WFx_ISS_WFxT))
 #define ESR_ELx_WFx_WFI_VAL	((ESR_ELx_EC_WFx << ESR_ELx_EC_SHIFT) |	\
 				 ESR_ELx_WFx_ISS_WFI)
 
@@ -327,17 +333,26 @@
 #define ESR_ELx_CP15_32_ISS_SYS_CNTFRQ	(ESR_ELx_CP15_32_ISS_SYS_VAL(0, 0, 14, 0) |\
 					 ESR_ELx_CP15_32_ISS_DIR_READ)
 
+/*
+ * ISS values for SME traps
+ */
+
+#define ESR_ELx_SME_ISS_SME_DISABLED	0
+#define ESR_ELx_SME_ISS_ILL		1
+#define ESR_ELx_SME_ISS_SM_DISABLED	2
+#define ESR_ELx_SME_ISS_ZA_DISABLED	3
+
 #ifndef __ASSEMBLY__
 #include <asm/types.h>
 
-static inline bool esr_is_data_abort(u32 esr)
+static inline bool esr_is_data_abort(unsigned long esr)
 {
-	const u32 ec = ESR_ELx_EC(esr);
+	const unsigned long ec = ESR_ELx_EC(esr);
 
 	return ec == ESR_ELx_EC_DABT_LOW || ec == ESR_ELx_EC_DABT_CUR;
 }
 
-const char *esr_get_class_string(u32 esr);
+const char *esr_get_class_string(unsigned long esr);
 #endif /* __ASSEMBLY */
 
 #endif /* __ASM_ESR_H */
diff --git a/arch/arm64/include/asm/exception.h b/arch/arm64/include/asm/exception.h
index 339477dca551..19713d0f013b 100644
--- a/arch/arm64/include/asm/exception.h
+++ b/arch/arm64/include/asm/exception.h
@@ -19,9 +19,9 @@
 #define __exception_irq_entry	__kprobes
 #endif
 
-static inline u32 disr_to_esr(u64 disr)
+static inline unsigned long disr_to_esr(u64 disr)
 {
-	unsigned int esr = ESR_ELx_EC_SERROR << ESR_ELx_EC_SHIFT;
+	unsigned long esr = ESR_ELx_EC_SERROR << ESR_ELx_EC_SHIFT;
 
 	if ((disr & DISR_EL1_IDS) == 0)
 		esr |= (disr & DISR_EL1_ESR_MASK);
@@ -57,23 +57,27 @@ asmlinkage void call_on_irq_stack(struct pt_regs *regs,
 				  void (*func)(struct pt_regs *));
 asmlinkage void asm_exit_to_user_mode(struct pt_regs *regs);
 
-void do_mem_abort(unsigned long far, unsigned int esr, struct pt_regs *regs);
-void do_undefinstr(struct pt_regs *regs);
-void do_bti(struct pt_regs *regs);
-void do_debug_exception(unsigned long addr_if_watchpoint, unsigned int esr,
+void do_mem_abort(unsigned long far, unsigned long esr, struct pt_regs *regs);
+void do_undefinstr(struct pt_regs *regs, unsigned long esr);
+void do_el0_bti(struct pt_regs *regs);
+void do_el1_bti(struct pt_regs *regs, unsigned long esr);
+void do_debug_exception(unsigned long addr_if_watchpoint, unsigned long esr,
 			struct pt_regs *regs);
-void do_fpsimd_acc(unsigned int esr, struct pt_regs *regs);
-void do_sve_acc(unsigned int esr, struct pt_regs *regs);
-void do_fpsimd_exc(unsigned int esr, struct pt_regs *regs);
-void do_sysinstr(unsigned int esr, struct pt_regs *regs);
-void do_sp_pc_abort(unsigned long addr, unsigned int esr, struct pt_regs *regs);
-void bad_el0_sync(struct pt_regs *regs, int reason, unsigned int esr);
-void do_cp15instr(unsigned int esr, struct pt_regs *regs);
+void do_fpsimd_acc(unsigned long esr, struct pt_regs *regs);
+void do_sve_acc(unsigned long esr, struct pt_regs *regs);
+void do_sme_acc(unsigned long esr, struct pt_regs *regs);
+void do_fpsimd_exc(unsigned long esr, struct pt_regs *regs);
+void do_sysinstr(unsigned long esr, struct pt_regs *regs);
+void do_sp_pc_abort(unsigned long addr, unsigned long esr, struct pt_regs *regs);
+void bad_el0_sync(struct pt_regs *regs, int reason, unsigned long esr);
+void do_cp15instr(unsigned long esr, struct pt_regs *regs);
+int do_compat_alignment_fixup(unsigned long addr, struct pt_regs *regs);
 void do_el0_svc(struct pt_regs *regs);
 void do_el0_svc_compat(struct pt_regs *regs);
-void do_ptrauth_fault(struct pt_regs *regs, unsigned int esr);
-void do_serror(struct pt_regs *regs, unsigned int esr);
+void do_el0_fpac(struct pt_regs *regs, unsigned long esr);
+void do_el1_fpac(struct pt_regs *regs, unsigned long esr);
+void do_serror(struct pt_regs *regs, unsigned long esr);
 void do_notify_resume(struct pt_regs *regs, unsigned long thread_flags);
 
-void panic_bad_stack(struct pt_regs *regs, unsigned int esr, unsigned long far);
+void panic_bad_stack(struct pt_regs *regs, unsigned long esr, unsigned long far);
 #endif	/* __ASM_EXCEPTION_H */
diff --git a/arch/arm64/include/asm/extable.h b/arch/arm64/include/asm/extable.h
index 8b300dd28def..72b0e71cc3de 100644
--- a/arch/arm64/include/asm/extable.h
+++ b/arch/arm64/include/asm/extable.h
@@ -33,15 +33,6 @@ do {							\
 	(b)->data = (tmp).data;				\
 } while (0)
 
-static inline bool in_bpf_jit(struct pt_regs *regs)
-{
-	if (!IS_ENABLED(CONFIG_BPF_JIT))
-		return false;
-
-	return regs->pc >= BPF_JIT_REGION_START &&
-	       regs->pc < BPF_JIT_REGION_END;
-}
-
 #ifdef CONFIG_BPF_JIT
 bool ex_handler_bpf(const struct exception_table_entry *ex,
 		    struct pt_regs *regs);
diff --git a/arch/arm64/include/asm/fixmap.h b/arch/arm64/include/asm/fixmap.h
index 4335800201c9..71ed5fdf718b 100644
--- a/arch/arm64/include/asm/fixmap.h
+++ b/arch/arm64/include/asm/fixmap.h
@@ -62,9 +62,13 @@ enum fixed_addresses {
 #endif /* CONFIG_ACPI_APEI_GHES */
 
 #ifdef CONFIG_UNMAP_KERNEL_AT_EL0
-	FIX_ENTRY_TRAMP_DATA,
-	FIX_ENTRY_TRAMP_TEXT,
-#define TRAMP_VALIAS		(__fix_to_virt(FIX_ENTRY_TRAMP_TEXT))
+#ifdef CONFIG_RELOCATABLE
+	FIX_ENTRY_TRAMP_TEXT4,	/* one extra slot for the data page */
+#endif
+	FIX_ENTRY_TRAMP_TEXT3,
+	FIX_ENTRY_TRAMP_TEXT2,
+	FIX_ENTRY_TRAMP_TEXT1,
+#define TRAMP_VALIAS		(__fix_to_virt(FIX_ENTRY_TRAMP_TEXT1))
 #endif /* CONFIG_UNMAP_KERNEL_AT_EL0 */
 	__end_of_permanent_fixed_addresses,
 
diff --git a/arch/arm64/include/asm/fpsimd.h b/arch/arm64/include/asm/fpsimd.h
index dbb4b30a5648..6f86b7ab6c28 100644
--- a/arch/arm64/include/asm/fpsimd.h
+++ b/arch/arm64/include/asm/fpsimd.h
@@ -32,6 +32,18 @@
 #define VFP_STATE_SIZE		((32 * 8) + 4)
 #endif
 
+/*
+ * When we defined the maximum SVE vector length we defined the ABI so
+ * that the maximum vector length included all the reserved for future
+ * expansion bits in ZCR rather than those just currently defined by
+ * the architecture. While SME follows a similar pattern the fact that
+ * it includes a square matrix means that any allocations that attempt
+ * to cover the maximum potential vector length (such as happen with
+ * the regset used for ptrace) end up being extremely large. Define
+ * the much lower actual limit for use in such situations.
+ */
+#define SME_VQ_MAX	16
+
 struct task_struct;
 
 extern void fpsimd_save_state(struct user_fpsimd_state *state);
@@ -46,13 +58,25 @@ extern void fpsimd_restore_current_state(void);
 extern void fpsimd_update_current_state(struct user_fpsimd_state const *state);
 
 extern void fpsimd_bind_state_to_cpu(struct user_fpsimd_state *state,
-				     void *sve_state, unsigned int sve_vl);
+				     void *sve_state, unsigned int sve_vl,
+				     void *za_state, unsigned int sme_vl,
+				     u64 *svcr);
 
 extern void fpsimd_flush_task_state(struct task_struct *target);
 extern void fpsimd_save_and_flush_cpu_state(void);
 
-/* Maximum VL that SVE VL-agnostic software can transparently support */
-#define SVE_VL_ARCH_MAX 0x100
+static inline bool thread_sm_enabled(struct thread_struct *thread)
+{
+	return system_supports_sme() && (thread->svcr & SVCR_SM_MASK);
+}
+
+static inline bool thread_za_enabled(struct thread_struct *thread)
+{
+	return system_supports_sme() && (thread->svcr & SVCR_ZA_MASK);
+}
+
+/* Maximum VL that SVE/SME VL-agnostic software can transparently support */
+#define VL_ARCH_MAX 0x100
 
 /* Offset of FFR in the SVE register dump */
 static inline size_t sve_ffr_offset(int vl)
@@ -62,7 +86,14 @@ static inline size_t sve_ffr_offset(int vl)
 
 static inline void *sve_pffr(struct thread_struct *thread)
 {
-	return (char *)thread->sve_state + sve_ffr_offset(thread_get_sve_vl(thread));
+	unsigned int vl;
+
+	if (system_supports_sme() && thread_sm_enabled(thread))
+		vl = thread_get_sme_vl(thread);
+	else
+		vl = thread_get_sve_vl(thread);
+
+	return (char *)thread->sve_state + sve_ffr_offset(vl);
 }
 
 extern void sve_save_state(void *state, u32 *pfpsr, int save_ffr);
@@ -71,11 +102,17 @@ extern void sve_load_state(void const *state, u32 const *pfpsr,
 extern void sve_flush_live(bool flush_ffr, unsigned long vq_minus_1);
 extern unsigned int sve_get_vl(void);
 extern void sve_set_vq(unsigned long vq_minus_1);
+extern void sme_set_vq(unsigned long vq_minus_1);
+extern void za_save_state(void *state);
+extern void za_load_state(void const *state);
 
 struct arm64_cpu_capabilities;
 extern void sve_kernel_enable(const struct arm64_cpu_capabilities *__unused);
+extern void sme_kernel_enable(const struct arm64_cpu_capabilities *__unused);
+extern void fa64_kernel_enable(const struct arm64_cpu_capabilities *__unused);
 
 extern u64 read_zcr_features(void);
+extern u64 read_smcr_features(void);
 
 /*
  * Helpers to translate bit indices in sve_vq_map to VQ values (and
@@ -116,13 +153,14 @@ struct vl_info {
 
 #ifdef CONFIG_ARM64_SVE
 
-extern void sve_alloc(struct task_struct *task);
+extern void sve_alloc(struct task_struct *task, bool flush);
 extern void fpsimd_release_task(struct task_struct *task);
 extern void fpsimd_sync_to_sve(struct task_struct *task);
+extern void fpsimd_force_sync_to_sve(struct task_struct *task);
 extern void sve_sync_to_fpsimd(struct task_struct *task);
 extern void sve_sync_from_fpsimd_zeropad(struct task_struct *task);
 
-extern int sve_set_vector_length(struct task_struct *task,
+extern int vec_set_vector_length(struct task_struct *task, enum vec_type type,
 				 unsigned long vl, unsigned long flags);
 
 extern int sve_set_current_vl(unsigned long arg);
@@ -171,6 +209,12 @@ static inline void write_vl(enum vec_type type, u64 val)
 		write_sysreg_s(tmp | val, SYS_ZCR_EL1);
 		break;
 #endif
+#ifdef CONFIG_ARM64_SME
+	case ARM64_VEC_SME:
+		tmp = read_sysreg_s(SYS_SMCR_EL1) & ~SMCR_ELx_LEN_MASK;
+		write_sysreg_s(tmp | val, SYS_SMCR_EL1);
+		break;
+#endif
 	default:
 		WARN_ON_ONCE(1);
 		break;
@@ -208,9 +252,11 @@ static inline bool sve_vq_available(unsigned int vq)
 	return vq_available(ARM64_VEC_SVE, vq);
 }
 
+size_t sve_state_size(struct task_struct const *task);
+
 #else /* ! CONFIG_ARM64_SVE */
 
-static inline void sve_alloc(struct task_struct *task) { }
+static inline void sve_alloc(struct task_struct *task, bool flush) { }
 static inline void fpsimd_release_task(struct task_struct *task) { }
 static inline void sve_sync_to_fpsimd(struct task_struct *task) { }
 static inline void sve_sync_from_fpsimd_zeropad(struct task_struct *task) { }
@@ -247,8 +293,93 @@ static inline void vec_update_vq_map(enum vec_type t) { }
 static inline int vec_verify_vq_map(enum vec_type t) { return 0; }
 static inline void sve_setup(void) { }
 
+static inline size_t sve_state_size(struct task_struct const *task)
+{
+	return 0;
+}
+
 #endif /* ! CONFIG_ARM64_SVE */
 
+#ifdef CONFIG_ARM64_SME
+
+static inline void sme_user_disable(void)
+{
+	sysreg_clear_set(cpacr_el1, CPACR_EL1_SMEN_EL0EN, 0);
+}
+
+static inline void sme_user_enable(void)
+{
+	sysreg_clear_set(cpacr_el1, 0, CPACR_EL1_SMEN_EL0EN);
+}
+
+static inline void sme_smstart_sm(void)
+{
+	asm volatile(__msr_s(SYS_SVCR_SMSTART_SM_EL0, "xzr"));
+}
+
+static inline void sme_smstop_sm(void)
+{
+	asm volatile(__msr_s(SYS_SVCR_SMSTOP_SM_EL0, "xzr"));
+}
+
+static inline void sme_smstop(void)
+{
+	asm volatile(__msr_s(SYS_SVCR_SMSTOP_SMZA_EL0, "xzr"));
+}
+
+extern void __init sme_setup(void);
+
+static inline int sme_max_vl(void)
+{
+	return vec_max_vl(ARM64_VEC_SME);
+}
+
+static inline int sme_max_virtualisable_vl(void)
+{
+	return vec_max_virtualisable_vl(ARM64_VEC_SME);
+}
+
+extern void sme_alloc(struct task_struct *task);
+extern unsigned int sme_get_vl(void);
+extern int sme_set_current_vl(unsigned long arg);
+extern int sme_get_current_vl(void);
+
+/*
+ * Return how many bytes of memory are required to store the full SME
+ * specific state (currently just ZA) for task, given task's currently
+ * configured vector length.
+ */
+static inline size_t za_state_size(struct task_struct const *task)
+{
+	unsigned int vl = task_get_sme_vl(task);
+
+	return ZA_SIG_REGS_SIZE(sve_vq_from_vl(vl));
+}
+
+#else
+
+static inline void sme_user_disable(void) { BUILD_BUG(); }
+static inline void sme_user_enable(void) { BUILD_BUG(); }
+
+static inline void sme_smstart_sm(void) { }
+static inline void sme_smstop_sm(void) { }
+static inline void sme_smstop(void) { }
+
+static inline void sme_alloc(struct task_struct *task) { }
+static inline void sme_setup(void) { }
+static inline unsigned int sme_get_vl(void) { return 0; }
+static inline int sme_max_vl(void) { return 0; }
+static inline int sme_max_virtualisable_vl(void) { return 0; }
+static inline int sme_set_current_vl(unsigned long arg) { return -EINVAL; }
+static inline int sme_get_current_vl(void) { return -EINVAL; }
+
+static inline size_t za_state_size(struct task_struct const *task)
+{
+	return 0;
+}
+
+#endif /* ! CONFIG_ARM64_SME */
+
 /* For use by EFI runtime services calls only */
 extern void __efi_fpsimd_begin(void);
 extern void __efi_fpsimd_end(void);
diff --git a/arch/arm64/include/asm/fpsimdmacros.h b/arch/arm64/include/asm/fpsimdmacros.h
index 2509d7dde55a..5e0910cf4832 100644
--- a/arch/arm64/include/asm/fpsimdmacros.h
+++ b/arch/arm64/include/asm/fpsimdmacros.h
@@ -93,6 +93,12 @@
 	.endif
 .endm
 
+.macro _sme_check_wv v
+	.if (\v) < 12 || (\v) > 15
+		.error "Bad vector select register \v."
+	.endif
+.endm
+
 /* SVE instruction encodings for non-SVE-capable assemblers */
 /* (pre binutils 2.28, all kernel capable clang versions support SVE) */
 
@@ -174,6 +180,54 @@
 		| (\np)
 .endm
 
+/* SME instruction encodings for non-SME-capable assemblers */
+/* (pre binutils 2.38/LLVM 13) */
+
+/* RDSVL X\nx, #\imm */
+.macro _sme_rdsvl nx, imm
+	_check_general_reg \nx
+	_check_num (\imm), -0x20, 0x1f
+	.inst	0x04bf5800			\
+		| (\nx)				\
+		| (((\imm) & 0x3f) << 5)
+.endm
+
+/*
+ * STR (vector from ZA array):
+ *	STR ZA[\nw, #\offset], [X\nxbase, #\offset, MUL VL]
+ */
+.macro _sme_str_zav nw, nxbase, offset=0
+	_sme_check_wv \nw
+	_check_general_reg \nxbase
+	_check_num (\offset), -0x100, 0xff
+	.inst	0xe1200000			\
+		| (((\nw) & 3) << 13)		\
+		| ((\nxbase) << 5)		\
+		| ((\offset) & 7)
+.endm
+
+/*
+ * LDR (vector to ZA array):
+ *	LDR ZA[\nw, #\offset], [X\nxbase, #\offset, MUL VL]
+ */
+.macro _sme_ldr_zav nw, nxbase, offset=0
+	_sme_check_wv \nw
+	_check_general_reg \nxbase
+	_check_num (\offset), -0x100, 0xff
+	.inst	0xe1000000			\
+		| (((\nw) & 3) << 13)		\
+		| ((\nxbase) << 5)		\
+		| ((\offset) & 7)
+.endm
+
+/*
+ * Zero the entire ZA array
+ *	ZERO ZA
+ */
+.macro zero_za
+	.inst 0xc00800ff
+.endm
+
 .macro __for from:req, to:req
 	.if (\from) == (\to)
 		_for__body %\from
@@ -208,6 +262,17 @@
 921:
 .endm
 
+/* Update SMCR_EL1.LEN with the new VQ */
+.macro sme_load_vq xvqminus1, xtmp, xtmp2
+		mrs_s		\xtmp, SYS_SMCR_EL1
+		bic		\xtmp2, \xtmp, SMCR_ELx_LEN_MASK
+		orr		\xtmp2, \xtmp2, \xvqminus1
+		cmp		\xtmp2, \xtmp
+		b.eq		921f
+		msr_s		SYS_SMCR_EL1, \xtmp2	//self-synchronising
+921:
+.endm
+
 /* Preserve the first 128-bits of Znz and zero the rest. */
 .macro _sve_flush_z nz
 	_sve_check_zreg \nz
@@ -254,3 +319,25 @@
 		ldr		w\nxtmp, [\xpfpsr, #4]
 		msr		fpcr, x\nxtmp
 .endm
+
+.macro sme_save_za nxbase, xvl, nw
+	mov	w\nw, #0
+
+423:
+	_sme_str_zav \nw, \nxbase
+	add	x\nxbase, x\nxbase, \xvl
+	add	x\nw, x\nw, #1
+	cmp	\xvl, x\nw
+	bne	423b
+.endm
+
+.macro sme_load_za nxbase, xvl, nw
+	mov	w\nw, #0
+
+423:
+	_sme_ldr_zav \nw, \nxbase
+	add	x\nxbase, x\nxbase, \xvl
+	add	x\nw, x\nw, #1
+	cmp	\xvl, x\nw
+	bne	423b
+.endm
diff --git a/arch/arm64/include/asm/ftrace.h b/arch/arm64/include/asm/ftrace.h
index 1494cfa8639b..329dbbd4d50b 100644
--- a/arch/arm64/include/asm/ftrace.h
+++ b/arch/arm64/include/asm/ftrace.h
@@ -26,7 +26,7 @@
 #ifdef CONFIG_DYNAMIC_FTRACE_WITH_REGS
 #define ARCH_SUPPORTS_FTRACE_OPS 1
 #else
-#define MCOUNT_ADDR		((unsigned long)function_nocfi(_mcount))
+#define MCOUNT_ADDR		((unsigned long)_mcount)
 #endif
 
 /* The BL at the callsite's adjusted rec->ip */
@@ -80,8 +80,15 @@ static inline unsigned long ftrace_call_adjust(unsigned long addr)
 
 #ifdef CONFIG_DYNAMIC_FTRACE_WITH_REGS
 struct dyn_ftrace;
+struct ftrace_ops;
+struct ftrace_regs;
+
 int ftrace_init_nop(struct module *mod, struct dyn_ftrace *rec);
 #define ftrace_init_nop ftrace_init_nop
+
+void ftrace_graph_func(unsigned long ip, unsigned long parent_ip,
+		       struct ftrace_ops *op, struct ftrace_regs *fregs);
+#define ftrace_graph_func ftrace_graph_func
 #endif
 
 #define ftrace_return_address(n) return_address(n)
diff --git a/arch/arm64/include/asm/hugetlb.h b/arch/arm64/include/asm/hugetlb.h
index 1242f71937f8..d20f5da2d76f 100644
--- a/arch/arm64/include/asm/hugetlb.h
+++ b/arch/arm64/include/asm/hugetlb.h
@@ -39,14 +39,13 @@ extern pte_t huge_ptep_get_and_clear(struct mm_struct *mm,
 extern void huge_ptep_set_wrprotect(struct mm_struct *mm,
 				    unsigned long addr, pte_t *ptep);
 #define __HAVE_ARCH_HUGE_PTEP_CLEAR_FLUSH
-extern void huge_ptep_clear_flush(struct vm_area_struct *vma,
-				  unsigned long addr, pte_t *ptep);
+extern pte_t huge_ptep_clear_flush(struct vm_area_struct *vma,
+				   unsigned long addr, pte_t *ptep);
 #define __HAVE_ARCH_HUGE_PTE_CLEAR
 extern void huge_pte_clear(struct mm_struct *mm, unsigned long addr,
 			   pte_t *ptep, unsigned long sz);
-extern void set_huge_swap_pte_at(struct mm_struct *mm, unsigned long addr,
-				 pte_t *ptep, pte_t pte, unsigned long sz);
-#define set_huge_swap_pte_at set_huge_swap_pte_at
+#define __HAVE_ARCH_HUGE_PTEP_GET
+extern pte_t huge_ptep_get(pte_t *ptep);
 
 void __init arm64_hugetlb_cma_reserve(void);
 
diff --git a/arch/arm64/include/asm/hw_breakpoint.h b/arch/arm64/include/asm/hw_breakpoint.h
index bc7aaed4b34e..fa4c6ff3aa9b 100644
--- a/arch/arm64/include/asm/hw_breakpoint.h
+++ b/arch/arm64/include/asm/hw_breakpoint.h
@@ -142,7 +142,7 @@ static inline int get_num_brps(void)
 	u64 dfr0 = read_sanitised_ftr_reg(SYS_ID_AA64DFR0_EL1);
 	return 1 +
 		cpuid_feature_extract_unsigned_field(dfr0,
-						ID_AA64DFR0_BRPS_SHIFT);
+						ID_AA64DFR0_EL1_BRPs_SHIFT);
 }
 
 /* Determine number of WRP registers available. */
@@ -151,7 +151,7 @@ static inline int get_num_wrps(void)
 	u64 dfr0 = read_sanitised_ftr_reg(SYS_ID_AA64DFR0_EL1);
 	return 1 +
 		cpuid_feature_extract_unsigned_field(dfr0,
-						ID_AA64DFR0_WRPS_SHIFT);
+						ID_AA64DFR0_EL1_WRPs_SHIFT);
 }
 
 #endif	/* __ASM_BREAKPOINT_H */
diff --git a/arch/arm64/include/asm/hwcap.h b/arch/arm64/include/asm/hwcap.h
index b100e0055eab..298b386d3ebe 100644
--- a/arch/arm64/include/asm/hwcap.h
+++ b/arch/arm64/include/asm/hwcap.h
@@ -85,7 +85,7 @@
 #define KERNEL_HWCAP_PACA		__khwcap_feature(PACA)
 #define KERNEL_HWCAP_PACG		__khwcap_feature(PACG)
 
-#define __khwcap2_feature(x)		(const_ilog2(HWCAP2_ ## x) + 32)
+#define __khwcap2_feature(x)		(const_ilog2(HWCAP2_ ## x) + 64)
 #define KERNEL_HWCAP_DCPODP		__khwcap2_feature(DCPODP)
 #define KERNEL_HWCAP_SVE2		__khwcap2_feature(SVE2)
 #define KERNEL_HWCAP_SVEAES		__khwcap2_feature(SVEAES)
@@ -106,6 +106,20 @@
 #define KERNEL_HWCAP_BTI		__khwcap2_feature(BTI)
 #define KERNEL_HWCAP_MTE		__khwcap2_feature(MTE)
 #define KERNEL_HWCAP_ECV		__khwcap2_feature(ECV)
+#define KERNEL_HWCAP_AFP		__khwcap2_feature(AFP)
+#define KERNEL_HWCAP_RPRES		__khwcap2_feature(RPRES)
+#define KERNEL_HWCAP_MTE3		__khwcap2_feature(MTE3)
+#define KERNEL_HWCAP_SME		__khwcap2_feature(SME)
+#define KERNEL_HWCAP_SME_I16I64		__khwcap2_feature(SME_I16I64)
+#define KERNEL_HWCAP_SME_F64F64		__khwcap2_feature(SME_F64F64)
+#define KERNEL_HWCAP_SME_I8I32		__khwcap2_feature(SME_I8I32)
+#define KERNEL_HWCAP_SME_F16F32		__khwcap2_feature(SME_F16F32)
+#define KERNEL_HWCAP_SME_B16F32		__khwcap2_feature(SME_B16F32)
+#define KERNEL_HWCAP_SME_F32F32		__khwcap2_feature(SME_F32F32)
+#define KERNEL_HWCAP_SME_FA64		__khwcap2_feature(SME_FA64)
+#define KERNEL_HWCAP_WFXT		__khwcap2_feature(WFXT)
+#define KERNEL_HWCAP_EBF16		__khwcap2_feature(EBF16)
+#define KERNEL_HWCAP_SVE_EBF16		__khwcap2_feature(SVE_EBF16)
 
 /*
  * This yields a mask that user programs can use to figure out what
diff --git a/arch/arm64/include/asm/hyperv-tlfs.h b/arch/arm64/include/asm/hyperv-tlfs.h
index 4d964a7f02ee..bc6c7ac934a1 100644
--- a/arch/arm64/include/asm/hyperv-tlfs.h
+++ b/arch/arm64/include/asm/hyperv-tlfs.h
@@ -64,6 +64,15 @@
 #define HV_REGISTER_STIMER0_CONFIG	0x000B0000
 #define HV_REGISTER_STIMER0_COUNT	0x000B0001
 
+union hv_msi_entry {
+	u64 as_uint64[2];
+	struct {
+		u64 address;
+		u32 data;
+		u32 reserved;
+	} __packed;
+};
+
 #include <asm-generic/hyperv-tlfs.h>
 
 #endif
diff --git a/arch/arm64/include/asm/insn-def.h b/arch/arm64/include/asm/insn-def.h
index 2c075f615c6a..1a7d0d483698 100644
--- a/arch/arm64/include/asm/insn-def.h
+++ b/arch/arm64/include/asm/insn-def.h
@@ -3,7 +3,21 @@
 #ifndef __ASM_INSN_DEF_H
 #define __ASM_INSN_DEF_H
 
+#include <asm/brk-imm.h>
+
 /* A64 instructions are always 32 bits. */
 #define	AARCH64_INSN_SIZE		4
 
+/*
+ * BRK instruction encoding
+ * The #imm16 value should be placed at bits[20:5] within BRK ins
+ */
+#define AARCH64_BREAK_MON	0xd4200000
+
+/*
+ * BRK instruction for provoking a fault on purpose
+ * Unlike kgdb, #imm16 value with unallocated handler is used for faulting.
+ */
+#define AARCH64_BREAK_FAULT	(AARCH64_BREAK_MON | (FAULT_BRK_IMM << 5))
+
 #endif /* __ASM_INSN_DEF_H */
diff --git a/arch/arm64/include/asm/insn.h b/arch/arm64/include/asm/insn.h
index 6b776c8667b2..834bff720582 100644
--- a/arch/arm64/include/asm/insn.h
+++ b/arch/arm64/include/asm/insn.h
@@ -65,6 +65,7 @@ enum aarch64_insn_hint_cr_op {
 	AARCH64_INSN_HINT_PSB  = 0x11 << 5,
 	AARCH64_INSN_HINT_TSB  = 0x12 << 5,
 	AARCH64_INSN_HINT_CSDB = 0x14 << 5,
+	AARCH64_INSN_HINT_CLEARBHB = 0x16 << 5,
 
 	AARCH64_INSN_HINT_BTI   = 0x20 << 5,
 	AARCH64_INSN_HINT_BTIC  = 0x22 << 5,
@@ -200,12 +201,16 @@ enum aarch64_insn_size_type {
 enum aarch64_insn_ldst_type {
 	AARCH64_INSN_LDST_LOAD_REG_OFFSET,
 	AARCH64_INSN_LDST_STORE_REG_OFFSET,
+	AARCH64_INSN_LDST_LOAD_IMM_OFFSET,
+	AARCH64_INSN_LDST_STORE_IMM_OFFSET,
 	AARCH64_INSN_LDST_LOAD_PAIR_PRE_INDEX,
 	AARCH64_INSN_LDST_STORE_PAIR_PRE_INDEX,
 	AARCH64_INSN_LDST_LOAD_PAIR_POST_INDEX,
 	AARCH64_INSN_LDST_STORE_PAIR_POST_INDEX,
 	AARCH64_INSN_LDST_LOAD_EX,
+	AARCH64_INSN_LDST_LOAD_ACQ_EX,
 	AARCH64_INSN_LDST_STORE_EX,
+	AARCH64_INSN_LDST_STORE_REL_EX,
 };
 
 enum aarch64_insn_adsb_type {
@@ -280,6 +285,36 @@ enum aarch64_insn_adr_type {
 	AARCH64_INSN_ADR_TYPE_ADR,
 };
 
+enum aarch64_insn_mem_atomic_op {
+	AARCH64_INSN_MEM_ATOMIC_ADD,
+	AARCH64_INSN_MEM_ATOMIC_CLR,
+	AARCH64_INSN_MEM_ATOMIC_EOR,
+	AARCH64_INSN_MEM_ATOMIC_SET,
+	AARCH64_INSN_MEM_ATOMIC_SWP,
+};
+
+enum aarch64_insn_mem_order_type {
+	AARCH64_INSN_MEM_ORDER_NONE,
+	AARCH64_INSN_MEM_ORDER_ACQ,
+	AARCH64_INSN_MEM_ORDER_REL,
+	AARCH64_INSN_MEM_ORDER_ACQREL,
+};
+
+enum aarch64_insn_mb_type {
+	AARCH64_INSN_MB_SY,
+	AARCH64_INSN_MB_ST,
+	AARCH64_INSN_MB_LD,
+	AARCH64_INSN_MB_ISH,
+	AARCH64_INSN_MB_ISHST,
+	AARCH64_INSN_MB_ISHLD,
+	AARCH64_INSN_MB_NSH,
+	AARCH64_INSN_MB_NSHST,
+	AARCH64_INSN_MB_NSHLD,
+	AARCH64_INSN_MB_OSH,
+	AARCH64_INSN_MB_OSHST,
+	AARCH64_INSN_MB_OSHLD,
+};
+
 #define	__AARCH64_INSN_FUNCS(abbr, mask, val)				\
 static __always_inline bool aarch64_insn_is_##abbr(u32 code)		\
 {									\
@@ -302,8 +337,15 @@ __AARCH64_INSN_FUNCS(load_pre,	0x3FE00C00, 0x38400C00)
 __AARCH64_INSN_FUNCS(store_post,	0x3FE00C00, 0x38000400)
 __AARCH64_INSN_FUNCS(load_post,	0x3FE00C00, 0x38400400)
 __AARCH64_INSN_FUNCS(str_reg,	0x3FE0EC00, 0x38206800)
+__AARCH64_INSN_FUNCS(str_imm,	0x3FC00000, 0x39000000)
 __AARCH64_INSN_FUNCS(ldadd,	0x3F20FC00, 0x38200000)
+__AARCH64_INSN_FUNCS(ldclr,	0x3F20FC00, 0x38201000)
+__AARCH64_INSN_FUNCS(ldeor,	0x3F20FC00, 0x38202000)
+__AARCH64_INSN_FUNCS(ldset,	0x3F20FC00, 0x38203000)
+__AARCH64_INSN_FUNCS(swp,	0x3F20FC00, 0x38208000)
+__AARCH64_INSN_FUNCS(cas,	0x3FA07C00, 0x08A07C00)
 __AARCH64_INSN_FUNCS(ldr_reg,	0x3FE0EC00, 0x38606800)
+__AARCH64_INSN_FUNCS(ldr_imm,	0x3FC00000, 0x39400000)
 __AARCH64_INSN_FUNCS(ldr_lit,	0xBF000000, 0x18000000)
 __AARCH64_INSN_FUNCS(ldrsw_lit,	0xFF000000, 0x98000000)
 __AARCH64_INSN_FUNCS(exclusive,	0x3F800000, 0x08000000)
@@ -463,6 +505,14 @@ u32 aarch64_insn_gen_load_store_reg(enum aarch64_insn_register reg,
 				    enum aarch64_insn_register offset,
 				    enum aarch64_insn_size_type size,
 				    enum aarch64_insn_ldst_type type);
+u32 aarch64_insn_gen_load_store_imm(enum aarch64_insn_register reg,
+				    enum aarch64_insn_register base,
+				    unsigned int imm,
+				    enum aarch64_insn_size_type size,
+				    enum aarch64_insn_ldst_type type);
+u32 aarch64_insn_gen_load_literal(unsigned long pc, unsigned long addr,
+				  enum aarch64_insn_register reg,
+				  bool is64bit);
 u32 aarch64_insn_gen_load_store_pair(enum aarch64_insn_register reg1,
 				     enum aarch64_insn_register reg2,
 				     enum aarch64_insn_register base,
@@ -474,13 +524,6 @@ u32 aarch64_insn_gen_load_store_ex(enum aarch64_insn_register reg,
 				   enum aarch64_insn_register state,
 				   enum aarch64_insn_size_type size,
 				   enum aarch64_insn_ldst_type type);
-u32 aarch64_insn_gen_ldadd(enum aarch64_insn_register result,
-			   enum aarch64_insn_register address,
-			   enum aarch64_insn_register value,
-			   enum aarch64_insn_size_type size);
-u32 aarch64_insn_gen_stadd(enum aarch64_insn_register address,
-			   enum aarch64_insn_register value,
-			   enum aarch64_insn_size_type size);
 u32 aarch64_insn_gen_add_sub_imm(enum aarch64_insn_register dst,
 				 enum aarch64_insn_register src,
 				 int imm, enum aarch64_insn_variant variant,
@@ -541,6 +584,42 @@ u32 aarch64_insn_gen_prefetch(enum aarch64_insn_register base,
 			      enum aarch64_insn_prfm_type type,
 			      enum aarch64_insn_prfm_target target,
 			      enum aarch64_insn_prfm_policy policy);
+#ifdef CONFIG_ARM64_LSE_ATOMICS
+u32 aarch64_insn_gen_atomic_ld_op(enum aarch64_insn_register result,
+				  enum aarch64_insn_register address,
+				  enum aarch64_insn_register value,
+				  enum aarch64_insn_size_type size,
+				  enum aarch64_insn_mem_atomic_op op,
+				  enum aarch64_insn_mem_order_type order);
+u32 aarch64_insn_gen_cas(enum aarch64_insn_register result,
+			 enum aarch64_insn_register address,
+			 enum aarch64_insn_register value,
+			 enum aarch64_insn_size_type size,
+			 enum aarch64_insn_mem_order_type order);
+#else
+static inline
+u32 aarch64_insn_gen_atomic_ld_op(enum aarch64_insn_register result,
+				  enum aarch64_insn_register address,
+				  enum aarch64_insn_register value,
+				  enum aarch64_insn_size_type size,
+				  enum aarch64_insn_mem_atomic_op op,
+				  enum aarch64_insn_mem_order_type order)
+{
+	return AARCH64_BREAK_FAULT;
+}
+
+static inline
+u32 aarch64_insn_gen_cas(enum aarch64_insn_register result,
+			 enum aarch64_insn_register address,
+			 enum aarch64_insn_register value,
+			 enum aarch64_insn_size_type size,
+			 enum aarch64_insn_mem_order_type order)
+{
+	return AARCH64_BREAK_FAULT;
+}
+#endif
+u32 aarch64_insn_gen_dmb(enum aarch64_insn_mb_type type);
+
 s32 aarch64_get_branch_offset(u32 insn);
 u32 aarch64_set_branch_offset(u32 insn, s32 offset);
 
diff --git a/arch/arm64/include/asm/io.h b/arch/arm64/include/asm/io.h
index 7fd836bea7eb..877495a0fd0c 100644
--- a/arch/arm64/include/asm/io.h
+++ b/arch/arm64/include/asm/io.h
@@ -91,7 +91,7 @@ static inline u64 __raw_readq(const volatile void __iomem *addr)
 }
 
 /* IO barriers */
-#define __iormb(v)							\
+#define __io_ar(v)							\
 ({									\
 	unsigned long tmp;						\
 									\
@@ -108,39 +108,14 @@ static inline u64 __raw_readq(const volatile void __iomem *addr)
 		     : "memory");					\
 })
 
-#define __io_par(v)		__iormb(v)
-#define __iowmb()		dma_wmb()
-#define __iomb()		dma_mb()
-
-/*
- * Relaxed I/O memory access primitives. These follow the Device memory
- * ordering rules but do not guarantee any ordering relative to Normal memory
- * accesses.
- */
-#define readb_relaxed(c)	({ u8  __r = __raw_readb(c); __r; })
-#define readw_relaxed(c)	({ u16 __r = le16_to_cpu((__force __le16)__raw_readw(c)); __r; })
-#define readl_relaxed(c)	({ u32 __r = le32_to_cpu((__force __le32)__raw_readl(c)); __r; })
-#define readq_relaxed(c)	({ u64 __r = le64_to_cpu((__force __le64)__raw_readq(c)); __r; })
-
-#define writeb_relaxed(v,c)	((void)__raw_writeb((v),(c)))
-#define writew_relaxed(v,c)	((void)__raw_writew((__force u16)cpu_to_le16(v),(c)))
-#define writel_relaxed(v,c)	((void)__raw_writel((__force u32)cpu_to_le32(v),(c)))
-#define writeq_relaxed(v,c)	((void)__raw_writeq((__force u64)cpu_to_le64(v),(c)))
-
-/*
- * I/O memory access primitives. Reads are ordered relative to any
- * following Normal memory access. Writes are ordered relative to any prior
- * Normal memory access.
- */
-#define readb(c)		({ u8  __v = readb_relaxed(c); __iormb(__v); __v; })
-#define readw(c)		({ u16 __v = readw_relaxed(c); __iormb(__v); __v; })
-#define readl(c)		({ u32 __v = readl_relaxed(c); __iormb(__v); __v; })
-#define readq(c)		({ u64 __v = readq_relaxed(c); __iormb(__v); __v; })
+#define __io_bw()		dma_wmb()
+#define __io_br(v)
+#define __io_aw(v)
 
-#define writeb(v,c)		({ __iowmb(); writeb_relaxed((v),(c)); })
-#define writew(v,c)		({ __iowmb(); writew_relaxed((v),(c)); })
-#define writel(v,c)		({ __iowmb(); writel_relaxed((v),(c)); })
-#define writeq(v,c)		({ __iowmb(); writeq_relaxed((v),(c)); })
+/* arm64-specific, don't use in portable drivers */
+#define __iormb(v)		__io_ar(v)
+#define __iowmb()		__io_bw()
+#define __iomb()		dma_mb()
 
 /*
  *  I/O port access primitives.
@@ -163,13 +138,16 @@ extern void __memset_io(volatile void __iomem *, int, size_t);
 /*
  * I/O memory mapping functions.
  */
-extern void __iomem *__ioremap(phys_addr_t phys_addr, size_t size, pgprot_t prot);
-extern void iounmap(volatile void __iomem *addr);
-extern void __iomem *ioremap_cache(phys_addr_t phys_addr, size_t size);
 
-#define ioremap(addr, size)		__ioremap((addr), (size), __pgprot(PROT_DEVICE_nGnRE))
-#define ioremap_wc(addr, size)		__ioremap((addr), (size), __pgprot(PROT_NORMAL_NC))
-#define ioremap_np(addr, size)		__ioremap((addr), (size), __pgprot(PROT_DEVICE_nGnRnE))
+bool ioremap_allowed(phys_addr_t phys_addr, size_t size, unsigned long prot);
+#define ioremap_allowed ioremap_allowed
+
+#define _PAGE_IOREMAP PROT_DEVICE_nGnRE
+
+#define ioremap_wc(addr, size)	\
+	ioremap_prot((addr), (size), PROT_NORMAL_NC)
+#define ioremap_np(addr, size)	\
+	ioremap_prot((addr), (size), PROT_DEVICE_nGnRnE)
 
 /*
  * io{read,write}{16,32,64}be() macros
@@ -184,6 +162,15 @@ extern void __iomem *ioremap_cache(phys_addr_t phys_addr, size_t size);
 
 #include <asm-generic/io.h>
 
+#define ioremap_cache ioremap_cache
+static inline void __iomem *ioremap_cache(phys_addr_t addr, size_t size)
+{
+	if (pfn_is_map_memory(__phys_to_pfn(addr)))
+		return (void __iomem *)__phys_to_virt(addr);
+
+	return ioremap_prot(addr, size, PROT_NORMAL);
+}
+
 /*
  * More restrictive address range checking than the default implementation
  * (PHYS_OFFSET and PHYS_MASK taken into account).
@@ -192,4 +179,8 @@ extern void __iomem *ioremap_cache(phys_addr_t phys_addr, size_t size);
 extern int valid_phys_addr_range(phys_addr_t addr, size_t size);
 extern int valid_mmap_phys_addr_range(unsigned long pfn, size_t size);
 
+extern bool arch_memremap_can_ram_remap(resource_size_t offset, size_t size,
+					unsigned long flags);
+#define arch_memremap_can_ram_remap arch_memremap_can_ram_remap
+
 #endif	/* __ASM_IO_H */
diff --git a/arch/arm64/include/asm/kernel-pgtable.h b/arch/arm64/include/asm/kernel-pgtable.h
index 96dc0f7da258..32d14f481f0c 100644
--- a/arch/arm64/include/asm/kernel-pgtable.h
+++ b/arch/arm64/include/asm/kernel-pgtable.h
@@ -8,6 +8,7 @@
 #ifndef __ASM_KERNEL_PGTABLE_H
 #define __ASM_KERNEL_PGTABLE_H
 
+#include <asm/boot.h>
 #include <asm/pgtable-hwdef.h>
 #include <asm/sparsemem.h>
 
@@ -35,10 +36,8 @@
  */
 #if ARM64_KERNEL_USES_PMD_MAPS
 #define SWAPPER_PGTABLE_LEVELS	(CONFIG_PGTABLE_LEVELS - 1)
-#define IDMAP_PGTABLE_LEVELS	(ARM64_HW_PGTABLE_LEVELS(PHYS_MASK_SHIFT) - 1)
 #else
 #define SWAPPER_PGTABLE_LEVELS	(CONFIG_PGTABLE_LEVELS)
-#define IDMAP_PGTABLE_LEVELS	(ARM64_HW_PGTABLE_LEVELS(PHYS_MASK_SHIFT))
 #endif
 
 
@@ -65,29 +64,36 @@
 #define EARLY_KASLR	(0)
 #endif
 
-#define EARLY_ENTRIES(vstart, vend, shift) \
-	((((vend) - 1) >> (shift)) - ((vstart) >> (shift)) + 1 + EARLY_KASLR)
+#define EARLY_ENTRIES(vstart, vend, shift, add) \
+	((((vend) - 1) >> (shift)) - ((vstart) >> (shift)) + 1 + add)
 
-#define EARLY_PGDS(vstart, vend) (EARLY_ENTRIES(vstart, vend, PGDIR_SHIFT))
+#define EARLY_PGDS(vstart, vend, add) (EARLY_ENTRIES(vstart, vend, PGDIR_SHIFT, add))
 
 #if SWAPPER_PGTABLE_LEVELS > 3
-#define EARLY_PUDS(vstart, vend) (EARLY_ENTRIES(vstart, vend, PUD_SHIFT))
+#define EARLY_PUDS(vstart, vend, add) (EARLY_ENTRIES(vstart, vend, PUD_SHIFT, add))
 #else
-#define EARLY_PUDS(vstart, vend) (0)
+#define EARLY_PUDS(vstart, vend, add) (0)
 #endif
 
 #if SWAPPER_PGTABLE_LEVELS > 2
-#define EARLY_PMDS(vstart, vend) (EARLY_ENTRIES(vstart, vend, SWAPPER_TABLE_SHIFT))
+#define EARLY_PMDS(vstart, vend, add) (EARLY_ENTRIES(vstart, vend, SWAPPER_TABLE_SHIFT, add))
 #else
-#define EARLY_PMDS(vstart, vend) (0)
+#define EARLY_PMDS(vstart, vend, add) (0)
 #endif
 
-#define EARLY_PAGES(vstart, vend) ( 1 			/* PGDIR page */				\
-			+ EARLY_PGDS((vstart), (vend)) 	/* each PGDIR needs a next level page table */	\
-			+ EARLY_PUDS((vstart), (vend))	/* each PUD needs a next level page table */	\
-			+ EARLY_PMDS((vstart), (vend)))	/* each PMD needs a next level page table */
-#define INIT_DIR_SIZE (PAGE_SIZE * EARLY_PAGES(KIMAGE_VADDR, _end))
-#define IDMAP_DIR_SIZE		(IDMAP_PGTABLE_LEVELS * PAGE_SIZE)
+#define EARLY_PAGES(vstart, vend, add) ( 1 			/* PGDIR page */				\
+			+ EARLY_PGDS((vstart), (vend), add) 	/* each PGDIR needs a next level page table */	\
+			+ EARLY_PUDS((vstart), (vend), add)	/* each PUD needs a next level page table */	\
+			+ EARLY_PMDS((vstart), (vend), add))	/* each PMD needs a next level page table */
+#define INIT_DIR_SIZE (PAGE_SIZE * EARLY_PAGES(KIMAGE_VADDR, _end, EARLY_KASLR))
+
+/* the initial ID map may need two extra pages if it needs to be extended */
+#if VA_BITS < 48
+#define INIT_IDMAP_DIR_SIZE	((INIT_IDMAP_DIR_PAGES + 2) * PAGE_SIZE)
+#else
+#define INIT_IDMAP_DIR_SIZE	(INIT_IDMAP_DIR_PAGES * PAGE_SIZE)
+#endif
+#define INIT_IDMAP_DIR_PAGES	EARLY_PAGES(KIMAGE_VADDR, _end + MAX_FDT_SIZE + SWAPPER_BLOCK_SIZE, 1)
 
 /* Initial memory map size */
 #if ARM64_KERNEL_USES_PMD_MAPS
@@ -107,9 +113,11 @@
 #define SWAPPER_PMD_FLAGS	(PMD_TYPE_SECT | PMD_SECT_AF | PMD_SECT_S)
 
 #if ARM64_KERNEL_USES_PMD_MAPS
-#define SWAPPER_MM_MMUFLAGS	(PMD_ATTRINDX(MT_NORMAL) | SWAPPER_PMD_FLAGS)
+#define SWAPPER_RW_MMUFLAGS	(PMD_ATTRINDX(MT_NORMAL) | SWAPPER_PMD_FLAGS)
+#define SWAPPER_RX_MMUFLAGS	(SWAPPER_RW_MMUFLAGS | PMD_SECT_RDONLY)
 #else
-#define SWAPPER_MM_MMUFLAGS	(PTE_ATTRINDX(MT_NORMAL) | SWAPPER_PTE_FLAGS)
+#define SWAPPER_RW_MMUFLAGS	(PTE_ATTRINDX(MT_NORMAL) | SWAPPER_PTE_FLAGS)
+#define SWAPPER_RX_MMUFLAGS	(SWAPPER_RW_MMUFLAGS | PTE_RDONLY)
 #endif
 
 /*
diff --git a/arch/arm64/include/asm/kexec.h b/arch/arm64/include/asm/kexec.h
index 9839bfc163d7..559bfae26715 100644
--- a/arch/arm64/include/asm/kexec.h
+++ b/arch/arm64/include/asm/kexec.h
@@ -84,16 +84,30 @@ static inline void crash_setup_regs(struct pt_regs *newregs,
 extern bool crash_is_nosave(unsigned long pfn);
 extern void crash_prepare_suspend(void);
 extern void crash_post_resume(void);
+
+void crash_free_reserved_phys_range(unsigned long begin, unsigned long end);
+#define crash_free_reserved_phys_range crash_free_reserved_phys_range
 #else
 static inline bool crash_is_nosave(unsigned long pfn) {return false; }
 static inline void crash_prepare_suspend(void) {}
 static inline void crash_post_resume(void) {}
 #endif
 
+struct kimage;
+
 #if defined(CONFIG_KEXEC_CORE)
 void cpu_soft_restart(unsigned long el2_switch, unsigned long entry,
 		      unsigned long arg0, unsigned long arg1,
 		      unsigned long arg2);
+
+int machine_kexec_post_load(struct kimage *image);
+#define machine_kexec_post_load machine_kexec_post_load
+
+void arch_kexec_protect_crashkres(void);
+#define arch_kexec_protect_crashkres arch_kexec_protect_crashkres
+
+void arch_kexec_unprotect_crashkres(void);
+#define arch_kexec_unprotect_crashkres arch_kexec_unprotect_crashkres
 #endif
 
 #define ARCH_HAS_KIMAGE_ARCH
@@ -113,9 +127,9 @@ struct kimage_arch {
 #ifdef CONFIG_KEXEC_FILE
 extern const struct kexec_file_ops kexec_image_ops;
 
-struct kimage;
+int arch_kimage_file_post_load_cleanup(struct kimage *image);
+#define arch_kimage_file_post_load_cleanup arch_kimage_file_post_load_cleanup
 
-extern int arch_kimage_file_post_load_cleanup(struct kimage *image);
 extern int load_other_segments(struct kimage *image,
 		unsigned long kernel_load_addr, unsigned long kernel_size,
 		char *initrd, unsigned long initrd_len,
diff --git a/arch/arm64/include/asm/kvm_arm.h b/arch/arm64/include/asm/kvm_arm.h
index 01d47c5886dc..8aa8492dafc0 100644
--- a/arch/arm64/include/asm/kvm_arm.h
+++ b/arch/arm64/include/asm/kvm_arm.h
@@ -80,11 +80,12 @@
  * FMO:		Override CPSR.F and enable signaling with VF
  * SWIO:	Turn set/way invalidates into set/way clean+invalidate
  * PTW:		Take a stage2 fault if a stage1 walk steps in device memory
+ * TID3:	Trap EL1 reads of group 3 ID registers
  */
 #define HCR_GUEST_FLAGS (HCR_TSC | HCR_TSW | HCR_TWE | HCR_TWI | HCR_VM | \
 			 HCR_BSU_IS | HCR_FB | HCR_TACR | \
 			 HCR_AMO | HCR_SWIO | HCR_TIDCP | HCR_RW | HCR_TLOR | \
-			 HCR_FMO | HCR_IMO | HCR_PTW )
+			 HCR_FMO | HCR_IMO | HCR_PTW | HCR_TID3 )
 #define HCR_VIRT_EXCP_MASK (HCR_VSE | HCR_VI | HCR_VF)
 #define HCR_HOST_NVHE_FLAGS (HCR_RW | HCR_API | HCR_APK | HCR_ATA)
 #define HCR_HOST_NVHE_PROTECTED_FLAGS (HCR_HOST_NVHE_FLAGS | HCR_TSC)
@@ -279,6 +280,7 @@
 #define CPTR_EL2_TCPAC	(1U << 31)
 #define CPTR_EL2_TAM	(1 << 30)
 #define CPTR_EL2_TTA	(1 << 20)
+#define CPTR_EL2_TSM	(1 << 12)
 #define CPTR_EL2_TFP	(1 << CPTR_EL2_TFP_SHIFT)
 #define CPTR_EL2_TZ	(1 << 8)
 #define CPTR_NVHE_EL2_RES1	0x000032ff /* known RES1 bits in CPTR_EL2 (nVHE) */
@@ -355,8 +357,8 @@
 	ECN(SOFTSTP_CUR), ECN(WATCHPT_LOW), ECN(WATCHPT_CUR), \
 	ECN(BKPT32), ECN(VECTOR32), ECN(BRK64)
 
-#define CPACR_EL1_FPEN		(3 << 20)
 #define CPACR_EL1_TTA		(1 << 28)
-#define CPACR_EL1_DEFAULT	(CPACR_EL1_FPEN | CPACR_EL1_ZEN_EL1EN)
+#define CPACR_EL1_DEFAULT	(CPACR_EL1_FPEN_EL0EN | CPACR_EL1_FPEN_EL1EN |\
+				 CPACR_EL1_ZEN_EL1EN)
 
 #endif /* __ARM64_KVM_ARM_H__ */
diff --git a/arch/arm64/include/asm/kvm_asm.h b/arch/arm64/include/asm/kvm_asm.h
index 50d5e4de244c..53035763e48e 100644
--- a/arch/arm64/include/asm/kvm_asm.h
+++ b/arch/arm64/include/asm/kvm_asm.h
@@ -63,6 +63,7 @@ enum __kvm_host_smccc_func {
 
 	/* Hypercalls available after pKVM finalisation */
 	__KVM_HOST_SMCCC_FUNC___pkvm_host_share_hyp,
+	__KVM_HOST_SMCCC_FUNC___pkvm_host_unshare_hyp,
 	__KVM_HOST_SMCCC_FUNC___kvm_adjust_pc,
 	__KVM_HOST_SMCCC_FUNC___kvm_vcpu_run,
 	__KVM_HOST_SMCCC_FUNC___kvm_flush_vm_context,
@@ -168,12 +169,29 @@ struct kvm_nvhe_init_params {
 	unsigned long tcr_el2;
 	unsigned long tpidr_el2;
 	unsigned long stack_hyp_va;
+	unsigned long stack_pa;
 	phys_addr_t pgd_pa;
 	unsigned long hcr_el2;
 	unsigned long vttbr;
 	unsigned long vtcr;
 };
 
+/*
+ * Used by the host in EL1 to dump the nVHE hypervisor backtrace on
+ * hyp_panic() in non-protected mode.
+ *
+ * @stack_base:                 hyp VA of the hyp_stack base.
+ * @overflow_stack_base:        hyp VA of the hyp_overflow_stack base.
+ * @fp:                         hyp FP where the backtrace begins.
+ * @pc:                         hyp PC where the backtrace begins.
+ */
+struct kvm_nvhe_stacktrace_info {
+	unsigned long stack_base;
+	unsigned long overflow_stack_base;
+	unsigned long fp;
+	unsigned long pc;
+};
+
 /* Translate a kernel address @ptr into its equivalent linear mapping */
 #define kvm_ksym_ref(ptr)						\
 	({								\
diff --git a/arch/arm64/include/asm/kvm_emulate.h b/arch/arm64/include/asm/kvm_emulate.h
index f4871e47b2d0..9bdba47f7e14 100644
--- a/arch/arm64/include/asm/kvm_emulate.h
+++ b/arch/arm64/include/asm/kvm_emulate.h
@@ -40,11 +40,26 @@ void kvm_inject_undefined(struct kvm_vcpu *vcpu);
 void kvm_inject_vabt(struct kvm_vcpu *vcpu);
 void kvm_inject_dabt(struct kvm_vcpu *vcpu, unsigned long addr);
 void kvm_inject_pabt(struct kvm_vcpu *vcpu, unsigned long addr);
+void kvm_inject_size_fault(struct kvm_vcpu *vcpu);
 
+void kvm_vcpu_wfi(struct kvm_vcpu *vcpu);
+
+#if defined(__KVM_VHE_HYPERVISOR__) || defined(__KVM_NVHE_HYPERVISOR__)
 static __always_inline bool vcpu_el1_is_32bit(struct kvm_vcpu *vcpu)
 {
 	return !(vcpu->arch.hcr_el2 & HCR_RW);
 }
+#else
+static __always_inline bool vcpu_el1_is_32bit(struct kvm_vcpu *vcpu)
+{
+	struct kvm *kvm = vcpu->kvm;
+
+	WARN_ON_ONCE(!test_bit(KVM_ARCH_FLAG_REG_WIDTH_CONFIGURED,
+			       &kvm->arch.flags));
+
+	return test_bit(KVM_ARCH_FLAG_EL1_32BIT, &kvm->arch.flags);
+}
+#endif
 
 static inline void vcpu_reset_hcr(struct kvm_vcpu *vcpu)
 {
@@ -70,17 +85,9 @@ static inline void vcpu_reset_hcr(struct kvm_vcpu *vcpu)
 		vcpu->arch.hcr_el2 |= HCR_TVM;
 	}
 
-	if (test_bit(KVM_ARM_VCPU_EL1_32BIT, vcpu->arch.features))
+	if (vcpu_el1_is_32bit(vcpu))
 		vcpu->arch.hcr_el2 &= ~HCR_RW;
 
-	/*
-	 * TID3: trap feature register accesses that we virtualise.
-	 * For now this is conditional, since no AArch32 feature regs
-	 * are currently virtualised.
-	 */
-	if (!vcpu_el1_is_32bit(vcpu))
-		vcpu->arch.hcr_el2 |= HCR_TID3;
-
 	if (cpus_have_const_cap(ARM64_MISMATCHED_CACHE_TYPE) ||
 	    vcpu_el1_is_32bit(vcpu))
 		vcpu->arch.hcr_el2 |= HCR_TID2;
@@ -222,14 +229,14 @@ static inline bool vcpu_mode_priv(const struct kvm_vcpu *vcpu)
 	return mode != PSR_MODE_EL0t;
 }
 
-static __always_inline u32 kvm_vcpu_get_esr(const struct kvm_vcpu *vcpu)
+static __always_inline u64 kvm_vcpu_get_esr(const struct kvm_vcpu *vcpu)
 {
 	return vcpu->arch.fault.esr_el2;
 }
 
 static __always_inline int kvm_vcpu_get_condition(const struct kvm_vcpu *vcpu)
 {
-	u32 esr = kvm_vcpu_get_esr(vcpu);
+	u64 esr = kvm_vcpu_get_esr(vcpu);
 
 	if (esr & ESR_ELx_CV)
 		return (esr & ESR_ELx_COND_MASK) >> ESR_ELx_COND_SHIFT;
@@ -360,7 +367,7 @@ static __always_inline bool kvm_vcpu_abt_issea(const struct kvm_vcpu *vcpu)
 
 static __always_inline int kvm_vcpu_sys_get_rt(struct kvm_vcpu *vcpu)
 {
-	u32 esr = kvm_vcpu_get_esr(vcpu);
+	u64 esr = kvm_vcpu_get_esr(vcpu);
 	return ESR_ELx_SYS64_ISS_RT(esr);
 }
 
@@ -386,7 +393,7 @@ static inline void kvm_vcpu_set_be(struct kvm_vcpu *vcpu)
 		*vcpu_cpsr(vcpu) |= PSR_AA32_E_BIT;
 	} else {
 		u64 sctlr = vcpu_read_sys_reg(vcpu, SCTLR_EL1);
-		sctlr |= (1 << 25);
+		sctlr |= SCTLR_ELx_EE;
 		vcpu_write_sys_reg(vcpu, sctlr, SCTLR_EL1);
 	}
 }
@@ -466,9 +473,18 @@ static inline unsigned long vcpu_data_host_to_guest(struct kvm_vcpu *vcpu,
 
 static __always_inline void kvm_incr_pc(struct kvm_vcpu *vcpu)
 {
-	vcpu->arch.flags |= KVM_ARM64_INCREMENT_PC;
+	WARN_ON(vcpu_get_flag(vcpu, PENDING_EXCEPTION));
+	vcpu_set_flag(vcpu, INCREMENT_PC);
 }
 
+#define kvm_pend_exception(v, e)					\
+	do {								\
+		WARN_ON(vcpu_get_flag((v), INCREMENT_PC));		\
+		vcpu_set_flag((v), PENDING_EXCEPTION);			\
+		vcpu_set_flag((v), e);					\
+	} while (0)
+
+
 static inline bool vcpu_has_feature(struct kvm_vcpu *vcpu, int feature)
 {
 	return test_bit(feature, vcpu->arch.features);
diff --git a/arch/arm64/include/asm/kvm_host.h b/arch/arm64/include/asm/kvm_host.h
index 2a5f7f38006f..45e2136322ba 100644
--- a/arch/arm64/include/asm/kvm_host.h
+++ b/arch/arm64/include/asm/kvm_host.h
@@ -26,7 +26,6 @@
 #include <asm/fpsimd.h>
 #include <asm/kvm.h>
 #include <asm/kvm_asm.h>
-#include <asm/thread_info.h>
 
 #define __KVM_HAVE_ARCH_INTC_INITIALIZED
 
@@ -47,10 +46,13 @@
 #define KVM_REQ_RECORD_STEAL	KVM_ARCH_REQ(3)
 #define KVM_REQ_RELOAD_GICv4	KVM_ARCH_REQ(4)
 #define KVM_REQ_RELOAD_PMU	KVM_ARCH_REQ(5)
+#define KVM_REQ_SUSPEND		KVM_ARCH_REQ(6)
 
 #define KVM_DIRTY_LOG_MANUAL_CAPS   (KVM_DIRTY_LOG_MANUAL_PROTECT_ENABLE | \
 				     KVM_DIRTY_LOG_INITIALLY_SET)
 
+#define KVM_HAVE_MMU_RWLOCK
+
 /*
  * Mode of operation configurable with kvm-arm.mode early param.
  * See Documentation/admin-guide/kernel-parameters.txt for more information.
@@ -72,9 +74,7 @@ int kvm_reset_vcpu(struct kvm_vcpu *vcpu);
 void kvm_arm_vcpu_destroy(struct kvm_vcpu *vcpu);
 
 struct kvm_vmid {
-	/* The VMID generation used for the virt. memory system */
-	u64    vmid_gen;
-	u32    vmid;
+	atomic64_t id;
 };
 
 struct kvm_s2_mmu {
@@ -102,15 +102,25 @@ struct kvm_s2_mmu {
 struct kvm_arch_memory_slot {
 };
 
+/**
+ * struct kvm_smccc_features: Descriptor of the hypercall services exposed to the guests
+ *
+ * @std_bmap: Bitmap of standard secure service calls
+ * @std_hyp_bmap: Bitmap of standard hypervisor service calls
+ * @vendor_hyp_bmap: Bitmap of vendor specific hypervisor service calls
+ */
+struct kvm_smccc_features {
+	unsigned long std_bmap;
+	unsigned long std_hyp_bmap;
+	unsigned long vendor_hyp_bmap;
+};
+
 struct kvm_arch {
 	struct kvm_s2_mmu mmu;
 
 	/* VTCR_EL2 value for this VM */
 	u64    vtcr;
 
-	/* The maximum number of vCPUs depends on the used GIC model */
-	int max_vcpus;
-
 	/* Interrupt controller */
 	struct vgic_dist	vgic;
 
@@ -123,24 +133,43 @@ struct kvm_arch {
 	 * should) opt in to this feature if KVM_CAP_ARM_NISV_TO_USER is
 	 * supported.
 	 */
-	bool return_nisv_io_abort_to_user;
+#define KVM_ARCH_FLAG_RETURN_NISV_IO_ABORT_TO_USER	0
+	/* Memory Tagging Extension enabled for the guest */
+#define KVM_ARCH_FLAG_MTE_ENABLED			1
+	/* At least one vCPU has ran in the VM */
+#define KVM_ARCH_FLAG_HAS_RAN_ONCE			2
+	/*
+	 * The following two bits are used to indicate the guest's EL1
+	 * register width configuration. A value of KVM_ARCH_FLAG_EL1_32BIT
+	 * bit is valid only when KVM_ARCH_FLAG_REG_WIDTH_CONFIGURED is set.
+	 * Otherwise, the guest's EL1 register width has not yet been
+	 * determined yet.
+	 */
+#define KVM_ARCH_FLAG_REG_WIDTH_CONFIGURED		3
+#define KVM_ARCH_FLAG_EL1_32BIT				4
+	/* PSCI SYSTEM_SUSPEND enabled for the guest */
+#define KVM_ARCH_FLAG_SYSTEM_SUSPEND_ENABLED		5
+
+	unsigned long flags;
 
 	/*
 	 * VM-wide PMU filter, implemented as a bitmap and big enough for
 	 * up to 2^10 events (ARMv8.0) or 2^16 events (ARMv8.1+).
 	 */
 	unsigned long *pmu_filter;
-	unsigned int pmuver;
+	struct arm_pmu *arm_pmu;
+
+	cpumask_var_t supported_cpus;
 
 	u8 pfr0_csv2;
 	u8 pfr0_csv3;
 
-	/* Memory Tagging Extension enabled for the guest */
-	bool mte_enabled;
+	/* Hypercall features firmware registers' descriptor */
+	struct kvm_smccc_features smccc_feat;
 };
 
 struct kvm_vcpu_fault_info {
-	u32 esr_el2;		/* Hyp Syndrom Register */
+	u64 esr_el2;		/* Hyp Syndrom Register */
 	u64 far_el2;		/* Hyp Fault Address Register */
 	u64 hpfar_el2;		/* Hyp IPA Fault Address Register */
 	u64 disr_el1;		/* Deferred [SError] Status Register */
@@ -172,6 +201,7 @@ enum vcpu_sysreg {
 	PAR_EL1,	/* Physical Address Register */
 	MDSCR_EL1,	/* Monitor Debug System Control Register */
 	MDCCINT_EL1,	/* Monitor Debug Comms Channel Interrupt Enable Reg */
+	OSLSR_EL1,	/* OS Lock Status Register */
 	DISR_EL1,	/* Deferred Interrupt Status Register */
 
 	/* Performance Monitors Registers */
@@ -240,14 +270,8 @@ struct kvm_cpu_context {
 	struct kvm_vcpu *__hyp_running_vcpu;
 };
 
-struct kvm_pmu_events {
-	u32 events_host;
-	u32 events_guest;
-};
-
 struct kvm_host_data {
 	struct kvm_cpu_context host_ctxt;
-	struct kvm_pmu_events pmu_events;
 };
 
 struct kvm_host_psci_config {
@@ -281,8 +305,11 @@ struct vcpu_reset_state {
 
 struct kvm_vcpu_arch {
 	struct kvm_cpu_context ctxt;
+
+	/* Guest floating point state */
 	void *sve_state;
 	unsigned int sve_max_vl;
+	u64 svcr;
 
 	/* Stage 2 paging state used by the hardware on next switch */
 	struct kvm_s2_mmu *hw_mmu;
@@ -298,11 +325,30 @@ struct kvm_vcpu_arch {
 	/* Exception Information */
 	struct kvm_vcpu_fault_info fault;
 
-	/* State of various workarounds, see kvm_asm.h for bit assignment */
-	u64 workaround_flags;
+	/* Ownership of the FP regs */
+	enum {
+		FP_STATE_FREE,
+		FP_STATE_HOST_OWNED,
+		FP_STATE_GUEST_OWNED,
+	} fp_state;
 
-	/* Miscellaneous vcpu state flags */
-	u64 flags;
+	/* Configuration flags, set once and for all before the vcpu can run */
+	u8 cflags;
+
+	/* Input flags to the hypervisor code, potentially cleared after use */
+	u8 iflags;
+
+	/* State flags for kernel bookkeeping, unused by the hypervisor code */
+	u8 sflags;
+
+	/*
+	 * Don't run the guest (internal implementation need).
+	 *
+	 * Contrary to the flags above, this is set/cleared outside of
+	 * a vcpu context, and thus cannot be mixed with the flags
+	 * themselves (or the flag accesses need to be made atomic).
+	 */
+	bool pause;
 
 	/*
 	 * We maintain more than a single set of debug registers to support
@@ -321,8 +367,8 @@ struct kvm_vcpu_arch {
 	struct kvm_guest_debug_arch vcpu_debug_state;
 	struct kvm_guest_debug_arch external_debug_state;
 
-	struct thread_info *host_thread_info;	/* hyp VA */
 	struct user_fpsimd_state *host_fpsimd_state;	/* hyp VA */
+	struct task_struct *parent_task;
 
 	struct {
 		/* {Break,watch}point registers */
@@ -339,11 +385,6 @@ struct kvm_vcpu_arch {
 	struct kvm_pmu pmu;
 
 	/*
-	 * Anything that is not used directly from assembly code goes
-	 * here.
-	 */
-
-	/*
 	 * Guest registers we preserve during guest debugging.
 	 *
 	 * These shadow registers are updated by the kvm_handle_sys_reg
@@ -352,13 +393,11 @@ struct kvm_vcpu_arch {
 	 */
 	struct {
 		u32	mdscr_el1;
+		bool	pstate_ss;
 	} guest_debug_preserved;
 
-	/* vcpu power-off state */
-	bool power_off;
-
-	/* Don't run the guest (internal implementation need) */
-	bool pause;
+	/* vcpu power state */
+	struct kvm_mp_state mp_state;
 
 	/* Cache some mmu pages needed inside spinlock regions */
 	struct kvm_mmu_memory_cache mmu_page_cache;
@@ -367,19 +406,12 @@ struct kvm_vcpu_arch {
 	int target;
 	DECLARE_BITMAP(features, KVM_VCPU_MAX_FEATURES);
 
-	/* Detect first run of a vcpu */
-	bool has_run_once;
-
 	/* Virtual SError ESR to restore when HCR_EL2.VSE is set */
 	u64 vsesr_el2;
 
 	/* Additional reset state */
 	struct vcpu_reset_state	reset_state;
 
-	/* True when deferrable sysregs are loaded on the physical CPU,
-	 * see kvm_vcpu_load_sysregs_vhe and kvm_vcpu_put_sysregs_vhe. */
-	bool sysregs_loaded_on_cpu;
-
 	/* Guest PV state */
 	struct {
 		u64 last_steal;
@@ -387,6 +419,127 @@ struct kvm_vcpu_arch {
 	} steal;
 };
 
+/*
+ * Each 'flag' is composed of a comma-separated triplet:
+ *
+ * - the flag-set it belongs to in the vcpu->arch structure
+ * - the value for that flag
+ * - the mask for that flag
+ *
+ *  __vcpu_single_flag() builds such a triplet for a single-bit flag.
+ * unpack_vcpu_flag() extract the flag value from the triplet for
+ * direct use outside of the flag accessors.
+ */
+#define __vcpu_single_flag(_set, _f)	_set, (_f), (_f)
+
+#define __unpack_flag(_set, _f, _m)	_f
+#define unpack_vcpu_flag(...)		__unpack_flag(__VA_ARGS__)
+
+#define __build_check_flag(v, flagset, f, m)			\
+	do {							\
+		typeof(v->arch.flagset) *_fset;			\
+								\
+		/* Check that the flags fit in the mask */	\
+		BUILD_BUG_ON(HWEIGHT(m) != HWEIGHT((f) | (m)));	\
+		/* Check that the flags fit in the type */	\
+		BUILD_BUG_ON((sizeof(*_fset) * 8) <= __fls(m));	\
+	} while (0)
+
+#define __vcpu_get_flag(v, flagset, f, m)			\
+	({							\
+		__build_check_flag(v, flagset, f, m);		\
+								\
+		v->arch.flagset & (m);				\
+	})
+
+#define __vcpu_set_flag(v, flagset, f, m)			\
+	do {							\
+		typeof(v->arch.flagset) *fset;			\
+								\
+		__build_check_flag(v, flagset, f, m);		\
+								\
+		fset = &v->arch.flagset;			\
+		if (HWEIGHT(m) > 1)				\
+			*fset &= ~(m);				\
+		*fset |= (f);					\
+	} while (0)
+
+#define __vcpu_clear_flag(v, flagset, f, m)			\
+	do {							\
+		typeof(v->arch.flagset) *fset;			\
+								\
+		__build_check_flag(v, flagset, f, m);		\
+								\
+		fset = &v->arch.flagset;			\
+		*fset &= ~(m);					\
+	} while (0)
+
+#define vcpu_get_flag(v, ...)	__vcpu_get_flag((v), __VA_ARGS__)
+#define vcpu_set_flag(v, ...)	__vcpu_set_flag((v), __VA_ARGS__)
+#define vcpu_clear_flag(v, ...)	__vcpu_clear_flag((v), __VA_ARGS__)
+
+/* SVE exposed to guest */
+#define GUEST_HAS_SVE		__vcpu_single_flag(cflags, BIT(0))
+/* SVE config completed */
+#define VCPU_SVE_FINALIZED	__vcpu_single_flag(cflags, BIT(1))
+/* PTRAUTH exposed to guest */
+#define GUEST_HAS_PTRAUTH	__vcpu_single_flag(cflags, BIT(2))
+
+/* Exception pending */
+#define PENDING_EXCEPTION	__vcpu_single_flag(iflags, BIT(0))
+/*
+ * PC increment. Overlaps with EXCEPT_MASK on purpose so that it can't
+ * be set together with an exception...
+ */
+#define INCREMENT_PC		__vcpu_single_flag(iflags, BIT(1))
+/* Target EL/MODE (not a single flag, but let's abuse the macro) */
+#define EXCEPT_MASK		__vcpu_single_flag(iflags, GENMASK(3, 1))
+
+/* Helpers to encode exceptions with minimum fuss */
+#define __EXCEPT_MASK_VAL	unpack_vcpu_flag(EXCEPT_MASK)
+#define __EXCEPT_SHIFT		__builtin_ctzl(__EXCEPT_MASK_VAL)
+#define __vcpu_except_flags(_f)	iflags, (_f << __EXCEPT_SHIFT), __EXCEPT_MASK_VAL
+
+/*
+ * When PENDING_EXCEPTION is set, EXCEPT_MASK can take the following
+ * values:
+ *
+ * For AArch32 EL1:
+ */
+#define EXCEPT_AA32_UND		__vcpu_except_flags(0)
+#define EXCEPT_AA32_IABT	__vcpu_except_flags(1)
+#define EXCEPT_AA32_DABT	__vcpu_except_flags(2)
+/* For AArch64: */
+#define EXCEPT_AA64_EL1_SYNC	__vcpu_except_flags(0)
+#define EXCEPT_AA64_EL1_IRQ	__vcpu_except_flags(1)
+#define EXCEPT_AA64_EL1_FIQ	__vcpu_except_flags(2)
+#define EXCEPT_AA64_EL1_SERR	__vcpu_except_flags(3)
+/* For AArch64 with NV (one day): */
+#define EXCEPT_AA64_EL2_SYNC	__vcpu_except_flags(4)
+#define EXCEPT_AA64_EL2_IRQ	__vcpu_except_flags(5)
+#define EXCEPT_AA64_EL2_FIQ	__vcpu_except_flags(6)
+#define EXCEPT_AA64_EL2_SERR	__vcpu_except_flags(7)
+/* Guest debug is live */
+#define DEBUG_DIRTY		__vcpu_single_flag(iflags, BIT(4))
+/* Save SPE context if active  */
+#define DEBUG_STATE_SAVE_SPE	__vcpu_single_flag(iflags, BIT(5))
+/* Save TRBE context if active  */
+#define DEBUG_STATE_SAVE_TRBE	__vcpu_single_flag(iflags, BIT(6))
+
+/* SVE enabled for host EL0 */
+#define HOST_SVE_ENABLED	__vcpu_single_flag(sflags, BIT(0))
+/* SME enabled for EL0 */
+#define HOST_SME_ENABLED	__vcpu_single_flag(sflags, BIT(1))
+/* Physical CPU not in supported_cpus */
+#define ON_UNSUPPORTED_CPU	__vcpu_single_flag(sflags, BIT(2))
+/* WFIT instruction trapped */
+#define IN_WFIT			__vcpu_single_flag(sflags, BIT(3))
+/* vcpu system registers loaded on physical CPU */
+#define SYSREGS_ON_CPU		__vcpu_single_flag(sflags, BIT(4))
+/* Software step state is Active-pending */
+#define DBG_SS_ACTIVE_PENDING	__vcpu_single_flag(sflags, BIT(5))
+
+
 /* Pointer to the vcpu's SVE FFR for sve_{save,load}_state() */
 #define vcpu_sve_pffr(vcpu) (kern_hyp_va((vcpu)->arch.sve_state) +	\
 			     sve_ffr_offset((vcpu)->arch.sve_max_vl))
@@ -407,59 +560,32 @@ struct kvm_vcpu_arch {
 	__size_ret;							\
 })
 
-/* vcpu_arch flags field values: */
-#define KVM_ARM64_DEBUG_DIRTY		(1 << 0)
-#define KVM_ARM64_FP_ENABLED		(1 << 1) /* guest FP regs loaded */
-#define KVM_ARM64_FP_HOST		(1 << 2) /* host FP regs loaded */
-#define KVM_ARM64_HOST_SVE_IN_USE	(1 << 3) /* backup for host TIF_SVE */
-#define KVM_ARM64_HOST_SVE_ENABLED	(1 << 4) /* SVE enabled for EL0 */
-#define KVM_ARM64_GUEST_HAS_SVE		(1 << 5) /* SVE exposed to guest */
-#define KVM_ARM64_VCPU_SVE_FINALIZED	(1 << 6) /* SVE config completed */
-#define KVM_ARM64_GUEST_HAS_PTRAUTH	(1 << 7) /* PTRAUTH exposed to guest */
-#define KVM_ARM64_PENDING_EXCEPTION	(1 << 8) /* Exception pending */
-#define KVM_ARM64_EXCEPT_MASK		(7 << 9) /* Target EL/MODE */
-#define KVM_ARM64_DEBUG_STATE_SAVE_SPE	(1 << 12) /* Save SPE context if active  */
-#define KVM_ARM64_DEBUG_STATE_SAVE_TRBE	(1 << 13) /* Save TRBE context if active  */
-
 #define KVM_GUESTDBG_VALID_MASK (KVM_GUESTDBG_ENABLE | \
 				 KVM_GUESTDBG_USE_SW_BP | \
 				 KVM_GUESTDBG_USE_HW | \
 				 KVM_GUESTDBG_SINGLESTEP)
-/*
- * When KVM_ARM64_PENDING_EXCEPTION is set, KVM_ARM64_EXCEPT_MASK can
- * take the following values:
- *
- * For AArch32 EL1:
- */
-#define KVM_ARM64_EXCEPT_AA32_UND	(0 << 9)
-#define KVM_ARM64_EXCEPT_AA32_IABT	(1 << 9)
-#define KVM_ARM64_EXCEPT_AA32_DABT	(2 << 9)
-/* For AArch64: */
-#define KVM_ARM64_EXCEPT_AA64_ELx_SYNC	(0 << 9)
-#define KVM_ARM64_EXCEPT_AA64_ELx_IRQ	(1 << 9)
-#define KVM_ARM64_EXCEPT_AA64_ELx_FIQ	(2 << 9)
-#define KVM_ARM64_EXCEPT_AA64_ELx_SERR	(3 << 9)
-#define KVM_ARM64_EXCEPT_AA64_EL1	(0 << 11)
-#define KVM_ARM64_EXCEPT_AA64_EL2	(1 << 11)
-
-/*
- * Overlaps with KVM_ARM64_EXCEPT_MASK on purpose so that it can't be
- * set together with an exception...
- */
-#define KVM_ARM64_INCREMENT_PC		(1 << 9) /* Increment PC */
 
 #define vcpu_has_sve(vcpu) (system_supports_sve() &&			\
-			    ((vcpu)->arch.flags & KVM_ARM64_GUEST_HAS_SVE))
+			    vcpu_get_flag(vcpu, GUEST_HAS_SVE))
 
 #ifdef CONFIG_ARM64_PTR_AUTH
 #define vcpu_has_ptrauth(vcpu)						\
 	((cpus_have_final_cap(ARM64_HAS_ADDRESS_AUTH) ||		\
 	  cpus_have_final_cap(ARM64_HAS_GENERIC_AUTH)) &&		\
-	 (vcpu)->arch.flags & KVM_ARM64_GUEST_HAS_PTRAUTH)
+	  vcpu_get_flag(vcpu, GUEST_HAS_PTRAUTH))
 #else
 #define vcpu_has_ptrauth(vcpu)		false
 #endif
 
+#define vcpu_on_unsupported_cpu(vcpu)					\
+	vcpu_get_flag(vcpu, ON_UNSUPPORTED_CPU)
+
+#define vcpu_set_on_unsupported_cpu(vcpu)				\
+	vcpu_set_flag(vcpu, ON_UNSUPPORTED_CPU)
+
+#define vcpu_clear_on_unsupported_cpu(vcpu)				\
+	vcpu_clear_flag(vcpu, ON_UNSUPPORTED_CPU)
+
 #define vcpu_gp_regs(v)		(&(v)->arch.ctxt.regs)
 
 /*
@@ -592,8 +718,6 @@ int kvm_arm_set_reg(struct kvm_vcpu *vcpu, const struct kvm_one_reg *reg);
 
 unsigned long kvm_arm_num_sys_reg_descs(struct kvm_vcpu *vcpu);
 int kvm_arm_copy_sys_reg_indices(struct kvm_vcpu *vcpu, u64 __user *uindices);
-int kvm_arm_sys_reg_get_reg(struct kvm_vcpu *vcpu, const struct kvm_one_reg *);
-int kvm_arm_sys_reg_set_reg(struct kvm_vcpu *vcpu, const struct kvm_one_reg *);
 
 int __kvm_arm_vcpu_get_events(struct kvm_vcpu *vcpu,
 			      struct kvm_vcpu_events *events);
@@ -606,6 +730,8 @@ int __kvm_arm_vcpu_set_events(struct kvm_vcpu *vcpu,
 void kvm_arm_halt_guest(struct kvm *kvm);
 void kvm_arm_resume_guest(struct kvm *kvm);
 
+#define vcpu_has_run_once(vcpu)	!!rcu_access_pointer((vcpu)->pid)
+
 #ifndef __KVM_NVHE_HYPERVISOR__
 #define kvm_call_hyp_nvhe(f, ...)						\
 	({								\
@@ -663,10 +789,11 @@ int kvm_handle_cp14_64(struct kvm_vcpu *vcpu);
 int kvm_handle_cp15_32(struct kvm_vcpu *vcpu);
 int kvm_handle_cp15_64(struct kvm_vcpu *vcpu);
 int kvm_handle_sys_reg(struct kvm_vcpu *vcpu);
+int kvm_handle_cp10_id(struct kvm_vcpu *vcpu);
 
 void kvm_reset_sys_regs(struct kvm_vcpu *vcpu);
 
-void kvm_sys_reg_table_init(void);
+int kvm_sys_reg_table_init(void);
 
 /* MMIO helpers */
 void kvm_mmio_write_buf(void *buf, unsigned int len, unsigned long data);
@@ -675,8 +802,15 @@ unsigned long kvm_mmio_read_buf(const void *buf, unsigned int len);
 int kvm_handle_mmio_return(struct kvm_vcpu *vcpu);
 int io_mem_abort(struct kvm_vcpu *vcpu, phys_addr_t fault_ipa);
 
-int kvm_perf_init(void);
-int kvm_perf_teardown(void);
+/*
+ * Returns true if a Performance Monitoring Interrupt (PMI), a.k.a. perf event,
+ * arrived in guest context.  For arm64, any event that arrives while a vCPU is
+ * loaded is considered to be "in guest".
+ */
+static inline bool kvm_arch_pmi_in_guest(struct kvm_vcpu *vcpu)
+{
+	return IS_ENABLED(CONFIG_GUEST_PERF_EVENTS) && !!vcpu;
+}
 
 long kvm_hypercall_pv_features(struct kvm_vcpu *vcpu);
 gpa_t kvm_init_stolen_time(struct kvm_vcpu *vcpu);
@@ -690,6 +824,12 @@ int kvm_arm_pvtime_get_attr(struct kvm_vcpu *vcpu,
 int kvm_arm_pvtime_has_attr(struct kvm_vcpu *vcpu,
 			    struct kvm_device_attr *attr);
 
+extern unsigned int kvm_arm_vmid_bits;
+int kvm_arm_vmid_alloc_init(void);
+void kvm_arm_vmid_alloc_free(void);
+void kvm_arm_vmid_update(struct kvm_vmid *kvm_vmid);
+void kvm_arm_vmid_clear_active(void);
+
 static inline void kvm_arm_pvtime_vcpu_init(struct kvm_vcpu_arch *vcpu_arch)
 {
 	vcpu_arch->steal.base = GPA_INVALID;
@@ -712,18 +852,26 @@ static inline void kvm_init_host_cpu_context(struct kvm_cpu_context *cpu_ctxt)
 	ctxt_sys_reg(cpu_ctxt, MPIDR_EL1) = read_cpuid_mpidr();
 }
 
+static inline bool kvm_system_needs_idmapped_vectors(void)
+{
+	return cpus_have_const_cap(ARM64_SPECTRE_V3A);
+}
+
 void kvm_arm_vcpu_ptrauth_trap(struct kvm_vcpu *vcpu);
 
 static inline void kvm_arch_hardware_unsetup(void) {}
 static inline void kvm_arch_sync_events(struct kvm *kvm) {}
 static inline void kvm_arch_sched_in(struct kvm_vcpu *vcpu, int cpu) {}
-static inline void kvm_arch_vcpu_block_finish(struct kvm_vcpu *vcpu) {}
 
 void kvm_arm_init_debug(void);
 void kvm_arm_vcpu_init_debug(struct kvm_vcpu *vcpu);
 void kvm_arm_setup_debug(struct kvm_vcpu *vcpu);
 void kvm_arm_clear_debug(struct kvm_vcpu *vcpu);
 void kvm_arm_reset_debug_ptr(struct kvm_vcpu *vcpu);
+
+#define kvm_vcpu_os_lock_enabled(vcpu)		\
+	(!!(__vcpu_sys_reg(vcpu, OSLSR_EL1) & SYS_OSLSR_OSLK))
+
 int kvm_arm_vcpu_arch_set_attr(struct kvm_vcpu *vcpu,
 			       struct kvm_device_attr *attr);
 int kvm_arm_vcpu_arch_get_attr(struct kvm_vcpu *vcpu,
@@ -737,8 +885,10 @@ long kvm_vm_ioctl_mte_copy_tags(struct kvm *kvm,
 /* Guest/host FPSIMD coordination helpers */
 int kvm_arch_vcpu_run_map_fp(struct kvm_vcpu *vcpu);
 void kvm_arch_vcpu_load_fp(struct kvm_vcpu *vcpu);
+void kvm_arch_vcpu_ctxflush_fp(struct kvm_vcpu *vcpu);
 void kvm_arch_vcpu_ctxsync_fp(struct kvm_vcpu *vcpu);
 void kvm_arch_vcpu_put_fp(struct kvm_vcpu *vcpu);
+void kvm_vcpu_unshare_task_fp(struct kvm_vcpu *vcpu);
 
 static inline bool kvm_pmu_counter_deferred(struct perf_event_attr *attr)
 {
@@ -749,17 +899,9 @@ static inline bool kvm_pmu_counter_deferred(struct perf_event_attr *attr)
 void kvm_arch_vcpu_load_debug_state_flags(struct kvm_vcpu *vcpu);
 void kvm_arch_vcpu_put_debug_state_flags(struct kvm_vcpu *vcpu);
 
-#ifdef CONFIG_KVM /* Avoid conflicts with core headers if CONFIG_KVM=n */
-static inline int kvm_arch_vcpu_run_pid_change(struct kvm_vcpu *vcpu)
-{
-	return kvm_arch_vcpu_run_map_fp(vcpu);
-}
-
+#ifdef CONFIG_KVM
 void kvm_set_pmu_events(u32 set, struct perf_event_attr *attr);
 void kvm_clr_pmu_events(u32 clr);
-
-void kvm_vcpu_pmu_restore_guest(struct kvm_vcpu *vcpu);
-void kvm_vcpu_pmu_restore_host(struct kvm_vcpu *vcpu);
 #else
 static inline void kvm_set_pmu_events(u32 set, struct perf_event_attr *attr) {}
 static inline void kvm_clr_pmu_events(u32 clr) {}
@@ -785,12 +927,15 @@ void kvm_init_protected_traps(struct kvm_vcpu *vcpu);
 int kvm_arm_vcpu_finalize(struct kvm_vcpu *vcpu, int feature);
 bool kvm_arm_vcpu_is_finalized(struct kvm_vcpu *vcpu);
 
-#define kvm_arm_vcpu_sve_finalized(vcpu) \
-	((vcpu)->arch.flags & KVM_ARM64_VCPU_SVE_FINALIZED)
+#define kvm_arm_vcpu_sve_finalized(vcpu) vcpu_get_flag(vcpu, VCPU_SVE_FINALIZED)
 
-#define kvm_has_mte(kvm) (system_supports_mte() && (kvm)->arch.mte_enabled)
-#define kvm_vcpu_has_pmu(vcpu)					\
-	(test_bit(KVM_ARM_VCPU_PMU_V3, (vcpu)->arch.features))
+#define kvm_has_mte(kvm)					\
+	(system_supports_mte() &&				\
+	 test_bit(KVM_ARCH_FLAG_MTE_ENABLED, &(kvm)->arch.flags))
+
+#define kvm_supports_32bit_el0()				\
+	(system_supports_32bit_el0() &&				\
+	 !static_branch_unlikely(&arm64_mismatched_32bit_el0))
 
 int kvm_trng_call(struct kvm_vcpu *vcpu);
 #ifdef CONFIG_KVM
@@ -801,4 +946,7 @@ void __init kvm_hyp_reserve(void);
 static inline void kvm_hyp_reserve(void) { }
 #endif
 
+void kvm_arm_vcpu_power_off(struct kvm_vcpu *vcpu);
+bool kvm_arm_vcpu_stopped(struct kvm_vcpu *vcpu);
+
 #endif /* __ARM64_KVM_HOST_H__ */
diff --git a/arch/arm64/include/asm/kvm_hyp.h b/arch/arm64/include/asm/kvm_hyp.h
index 5afd14ab15b9..aa7fa2a08f06 100644
--- a/arch/arm64/include/asm/kvm_hyp.h
+++ b/arch/arm64/include/asm/kvm_hyp.h
@@ -90,7 +90,6 @@ void __debug_restore_host_buffers_nvhe(struct kvm_vcpu *vcpu);
 
 void __fpsimd_save_state(struct user_fpsimd_state *fp_regs);
 void __fpsimd_restore_state(struct user_fpsimd_state *fp_regs);
-void __sve_save_state(void *sve_pffr, u32 *fpsr);
 void __sve_restore_state(void *sve_pffr, u32 *fpsr);
 
 #ifndef __KVM_NVHE_HYPERVISOR__
@@ -119,6 +118,7 @@ extern u64 kvm_nvhe_sym(id_aa64pfr0_el1_sys_val);
 extern u64 kvm_nvhe_sym(id_aa64pfr1_el1_sys_val);
 extern u64 kvm_nvhe_sym(id_aa64isar0_el1_sys_val);
 extern u64 kvm_nvhe_sym(id_aa64isar1_el1_sys_val);
+extern u64 kvm_nvhe_sym(id_aa64isar2_el1_sys_val);
 extern u64 kvm_nvhe_sym(id_aa64mmfr0_el1_sys_val);
 extern u64 kvm_nvhe_sym(id_aa64mmfr1_el1_sys_val);
 extern u64 kvm_nvhe_sym(id_aa64mmfr2_el1_sys_val);
diff --git a/arch/arm64/include/asm/kvm_mmu.h b/arch/arm64/include/asm/kvm_mmu.h
index 02d378887743..7784081088e7 100644
--- a/arch/arm64/include/asm/kvm_mmu.h
+++ b/arch/arm64/include/asm/kvm_mmu.h
@@ -63,7 +63,7 @@
  * specific registers encoded in the instructions).
  */
 .macro kern_hyp_va	reg
-alternative_cb kvm_update_va_mask
+alternative_cb ARM64_ALWAYS_SYSTEM, kvm_update_va_mask
 	and     \reg, \reg, #1		/* mask with va_mask */
 	ror	\reg, \reg, #1		/* rotate to the first tag bit */
 	add	\reg, \reg, #0		/* insert the low 12 bits of the tag */
@@ -97,7 +97,7 @@ alternative_cb_end
 	hyp_pa	\reg, \tmp
 
 	/* Load kimage_voffset. */
-alternative_cb kvm_get_kimage_voffset
+alternative_cb ARM64_ALWAYS_SYSTEM, kvm_get_kimage_voffset
 	movz	\tmp, #0
 	movk	\tmp, #0, lsl #16
 	movk	\tmp, #0, lsl #32
@@ -115,6 +115,7 @@ alternative_cb_end
 #include <asm/cache.h>
 #include <asm/cacheflush.h>
 #include <asm/mmu_context.h>
+#include <asm/kvm_host.h>
 
 void kvm_update_va_mask(struct alt_instr *alt,
 			__le32 *origptr, __le32 *updptr, int nr_inst);
@@ -130,6 +131,7 @@ static __always_inline unsigned long __kern_hyp_va(unsigned long v)
 				    "add %0, %0, #0\n"
 				    "add %0, %0, #0, lsl 12\n"
 				    "ror %0, %0, #63\n",
+				    ARM64_ALWAYS_SYSTEM,
 				    kvm_update_va_mask)
 		     : "+r" (v));
 	return v;
@@ -150,7 +152,12 @@ static __always_inline unsigned long __kern_hyp_va(unsigned long v)
 #include <asm/kvm_pgtable.h>
 #include <asm/stage2_pgtable.h>
 
+int kvm_share_hyp(void *from, void *to);
+void kvm_unshare_hyp(void *from, void *to);
 int create_hyp_mappings(void *from, void *to, enum kvm_pgtable_prot prot);
+int __create_hyp_mappings(unsigned long start, unsigned long size,
+			  unsigned long phys, enum kvm_pgtable_prot prot);
+int hyp_alloc_private_va_range(size_t size, unsigned long *haddr);
 int create_hyp_io_mappings(phys_addr_t phys_addr, size_t size,
 			   void __iomem **kaddr,
 			   void __iomem **haddr);
@@ -264,7 +271,8 @@ static __always_inline u64 kvm_get_vttbr(struct kvm_s2_mmu *mmu)
 	u64 cnp = system_supports_cnp() ? VTTBR_CNP_BIT : 0;
 
 	baddr = mmu->pgd_phys;
-	vmid_field = (u64)READ_ONCE(vmid->vmid) << VTTBR_VMID_SHIFT;
+	vmid_field = atomic64_read(&vmid->id) << VTTBR_VMID_SHIFT;
+	vmid_field &= VTTBR_VMID_MASK(kvm_arm_vmid_bits);
 	return kvm_phys_to_vttbr(baddr) | vmid_field | cnp;
 }
 
diff --git a/arch/arm64/include/asm/kvm_pgtable.h b/arch/arm64/include/asm/kvm_pgtable.h
index 027783829584..3252eb50ecfe 100644
--- a/arch/arm64/include/asm/kvm_pgtable.h
+++ b/arch/arm64/include/asm/kvm_pgtable.h
@@ -13,12 +13,24 @@
 
 #define KVM_PGTABLE_MAX_LEVELS		4U
 
+/*
+ * The largest supported block sizes for KVM (no 52-bit PA support):
+ *  - 4K (level 1):	1GB
+ *  - 16K (level 2):	32MB
+ *  - 64K (level 2):	512MB
+ */
+#ifdef CONFIG_ARM64_4K_PAGES
+#define KVM_PGTABLE_MIN_BLOCK_LEVEL	1U
+#else
+#define KVM_PGTABLE_MIN_BLOCK_LEVEL	2U
+#endif
+
 static inline u64 kvm_get_parange(u64 mmfr0)
 {
 	u64 parange = cpuid_feature_extract_unsigned_field(mmfr0,
-				ID_AA64MMFR0_PARANGE_SHIFT);
-	if (parange > ID_AA64MMFR0_PARANGE_MAX)
-		parange = ID_AA64MMFR0_PARANGE_MAX;
+				ID_AA64MMFR0_EL1_PARANGE_SHIFT);
+	if (parange > ID_AA64MMFR0_EL1_PARANGE_MAX)
+		parange = ID_AA64MMFR0_EL1_PARANGE_MAX;
 
 	return parange;
 }
@@ -58,11 +70,7 @@ static inline u64 kvm_granule_size(u32 level)
 
 static inline bool kvm_level_supports_block_mapping(u32 level)
 {
-	/*
-	 * Reject invalid block mappings and don't bother with 4TB mappings for
-	 * 52-bit PAs.
-	 */
-	return !(level == 0 || (PAGE_SIZE != SZ_4K && level == 1));
+	return level >= KVM_PGTABLE_MIN_BLOCK_LEVEL;
 }
 
 /**
@@ -252,6 +260,27 @@ int kvm_pgtable_hyp_map(struct kvm_pgtable *pgt, u64 addr, u64 size, u64 phys,
 			enum kvm_pgtable_prot prot);
 
 /**
+ * kvm_pgtable_hyp_unmap() - Remove a mapping from a hypervisor stage-1 page-table.
+ * @pgt:	Page-table structure initialised by kvm_pgtable_hyp_init().
+ * @addr:	Virtual address from which to remove the mapping.
+ * @size:	Size of the mapping.
+ *
+ * The offset of @addr within a page is ignored, @size is rounded-up to
+ * the next page boundary and @phys is rounded-down to the previous page
+ * boundary.
+ *
+ * TLB invalidation is performed for each page-table entry cleared during the
+ * unmapping operation and the reference count for the page-table page
+ * containing the cleared entry is decremented, with unreferenced pages being
+ * freed. The unmapping operation will stop early if it encounters either an
+ * invalid page-table entry or a valid block mapping which maps beyond the range
+ * being unmapped.
+ *
+ * Return: Number of bytes unmapped, which may be 0.
+ */
+u64 kvm_pgtable_hyp_unmap(struct kvm_pgtable *pgt, u64 addr, u64 size);
+
+/**
  * kvm_get_vtcr() - Helper to construct VTCR_EL2
  * @mmfr0:	Sanitized value of SYS_ID_AA64MMFR0_EL1 register.
  * @mmfr1:	Sanitized value of SYS_ID_AA64MMFR1_EL1 register.
@@ -270,8 +299,7 @@ u64 kvm_get_vtcr(u64 mmfr0, u64 mmfr1, u32 phys_shift);
 /**
  * __kvm_pgtable_stage2_init() - Initialise a guest stage-2 page-table.
  * @pgt:	Uninitialised page-table structure to initialise.
- * @arch:	Arch-specific KVM structure representing the guest virtual
- *		machine.
+ * @mmu:	S2 MMU context for this S2 translation
  * @mm_ops:	Memory management callbacks.
  * @flags:	Stage-2 configuration flags.
  * @force_pte_cb: Function that returns true if page level mappings must
@@ -279,13 +307,13 @@ u64 kvm_get_vtcr(u64 mmfr0, u64 mmfr1, u32 phys_shift);
  *
  * Return: 0 on success, negative error code on failure.
  */
-int __kvm_pgtable_stage2_init(struct kvm_pgtable *pgt, struct kvm_arch *arch,
+int __kvm_pgtable_stage2_init(struct kvm_pgtable *pgt, struct kvm_s2_mmu *mmu,
 			      struct kvm_pgtable_mm_ops *mm_ops,
 			      enum kvm_pgtable_stage2_flags flags,
 			      kvm_pgtable_force_pte_cb_t force_pte_cb);
 
-#define kvm_pgtable_stage2_init(pgt, arch, mm_ops) \
-	__kvm_pgtable_stage2_init(pgt, arch, mm_ops, 0, NULL)
+#define kvm_pgtable_stage2_init(pgt, mmu, mm_ops) \
+	__kvm_pgtable_stage2_init(pgt, mmu, mm_ops, 0, NULL)
 
 /**
  * kvm_pgtable_stage2_destroy() - Destroy an unused guest stage-2 page-table.
diff --git a/arch/arm64/include/asm/kvm_pkvm.h b/arch/arm64/include/asm/kvm_pkvm.h
new file mode 100644
index 000000000000..9f4ad2a8df59
--- /dev/null
+++ b/arch/arm64/include/asm/kvm_pkvm.h
@@ -0,0 +1,71 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2020 - Google LLC
+ * Author: Quentin Perret <qperret@google.com>
+ */
+#ifndef __ARM64_KVM_PKVM_H__
+#define __ARM64_KVM_PKVM_H__
+
+#include <linux/memblock.h>
+#include <asm/kvm_pgtable.h>
+
+#define HYP_MEMBLOCK_REGIONS 128
+
+extern struct memblock_region kvm_nvhe_sym(hyp_memory)[];
+extern unsigned int kvm_nvhe_sym(hyp_memblock_nr);
+
+static inline unsigned long __hyp_pgtable_max_pages(unsigned long nr_pages)
+{
+	unsigned long total = 0, i;
+
+	/* Provision the worst case scenario */
+	for (i = 0; i < KVM_PGTABLE_MAX_LEVELS; i++) {
+		nr_pages = DIV_ROUND_UP(nr_pages, PTRS_PER_PTE);
+		total += nr_pages;
+	}
+
+	return total;
+}
+
+static inline unsigned long __hyp_pgtable_total_pages(void)
+{
+	unsigned long res = 0, i;
+
+	/* Cover all of memory with page-granularity */
+	for (i = 0; i < kvm_nvhe_sym(hyp_memblock_nr); i++) {
+		struct memblock_region *reg = &kvm_nvhe_sym(hyp_memory)[i];
+		res += __hyp_pgtable_max_pages(reg->size >> PAGE_SHIFT);
+	}
+
+	return res;
+}
+
+static inline unsigned long hyp_s1_pgtable_pages(void)
+{
+	unsigned long res;
+
+	res = __hyp_pgtable_total_pages();
+
+	/* Allow 1 GiB for private mappings */
+	res += __hyp_pgtable_max_pages(SZ_1G >> PAGE_SHIFT);
+
+	return res;
+}
+
+static inline unsigned long host_s2_pgtable_pages(void)
+{
+	unsigned long res;
+
+	/*
+	 * Include an extra 16 pages to safely upper-bound the worst case of
+	 * concatenated pgds.
+	 */
+	res = __hyp_pgtable_total_pages() + 16;
+
+	/* Allow 1 GiB for MMIO mappings */
+	res += __hyp_pgtable_max_pages(SZ_1G >> PAGE_SHIFT);
+
+	return res;
+}
+
+#endif	/* __ARM64_KVM_PKVM_H__ */
diff --git a/arch/arm64/include/asm/kvm_ras.h b/arch/arm64/include/asm/kvm_ras.h
index 8ac6ee77437c..87e10d9a635b 100644
--- a/arch/arm64/include/asm/kvm_ras.h
+++ b/arch/arm64/include/asm/kvm_ras.h
@@ -14,7 +14,7 @@
  * Was this synchronous external abort a RAS notification?
  * Returns '0' for errors handled by some RAS subsystem, or -ENOENT.
  */
-static inline int kvm_handle_guest_sea(phys_addr_t addr, unsigned int esr)
+static inline int kvm_handle_guest_sea(phys_addr_t addr, u64 esr)
 {
 	/* apei_claim_sea(NULL) expects to mask interrupts itself */
 	lockdep_assert_irqs_enabled();
diff --git a/arch/arm64/include/asm/linkage.h b/arch/arm64/include/asm/linkage.h
index 9906541a6861..1436fa1cde24 100644
--- a/arch/arm64/include/asm/linkage.h
+++ b/arch/arm64/include/asm/linkage.h
@@ -1,71 +1,46 @@
 #ifndef __ASM_LINKAGE_H
 #define __ASM_LINKAGE_H
 
+#ifdef __ASSEMBLY__
+#include <asm/assembler.h>
+#endif
+
 #define __ALIGN		.align 2
 #define __ALIGN_STR	".align 2"
 
-#if defined(CONFIG_ARM64_BTI_KERNEL) && defined(__aarch64__)
-
 /*
- * Since current versions of gas reject the BTI instruction unless we
- * set the architecture version to v8.5 we use the hint instruction
- * instead.
- */
-#define BTI_C hint 34 ;
-
-/*
- * When using in-kernel BTI we need to ensure that PCS-conformant assembly
- * functions have suitable annotations.  Override SYM_FUNC_START to insert
- * a BTI landing pad at the start of everything.
+ * When using in-kernel BTI we need to ensure that PCS-conformant
+ * assembly functions have suitable annotations.  Override
+ * SYM_FUNC_START to insert a BTI landing pad at the start of
+ * everything, the override is done unconditionally so we're more
+ * likely to notice any drift from the overridden definitions.
  */
 #define SYM_FUNC_START(name)				\
 	SYM_START(name, SYM_L_GLOBAL, SYM_A_ALIGN)	\
-	BTI_C
+	bti c ;
 
 #define SYM_FUNC_START_NOALIGN(name)			\
 	SYM_START(name, SYM_L_GLOBAL, SYM_A_NONE)	\
-	BTI_C
+	bti c ;
 
 #define SYM_FUNC_START_LOCAL(name)			\
 	SYM_START(name, SYM_L_LOCAL, SYM_A_ALIGN)	\
-	BTI_C
+	bti c ;
 
 #define SYM_FUNC_START_LOCAL_NOALIGN(name)		\
 	SYM_START(name, SYM_L_LOCAL, SYM_A_NONE)	\
-	BTI_C
+	bti c ;
 
 #define SYM_FUNC_START_WEAK(name)			\
 	SYM_START(name, SYM_L_WEAK, SYM_A_ALIGN)	\
-	BTI_C
+	bti c ;
 
 #define SYM_FUNC_START_WEAK_NOALIGN(name)		\
 	SYM_START(name, SYM_L_WEAK, SYM_A_NONE)		\
-	BTI_C
-
-#endif
-
-/*
- * Annotate a function as position independent, i.e., safe to be called before
- * the kernel virtual mapping is activated.
- */
-#define SYM_FUNC_START_PI(x)			\
-		SYM_FUNC_START_ALIAS(__pi_##x);	\
-		SYM_FUNC_START(x)
-
-#define SYM_FUNC_START_WEAK_PI(x)		\
-		SYM_FUNC_START_ALIAS(__pi_##x);	\
-		SYM_FUNC_START_WEAK(x)
-
-#define SYM_FUNC_START_WEAK_ALIAS_PI(x)		\
-		SYM_FUNC_START_ALIAS(__pi_##x);	\
-		SYM_START(x, SYM_L_WEAK, SYM_A_ALIGN)
-
-#define SYM_FUNC_END_PI(x)			\
-		SYM_FUNC_END(x);		\
-		SYM_FUNC_END_ALIAS(__pi_##x)
+	bti c ;
 
-#define SYM_FUNC_END_ALIAS_PI(x)		\
-		SYM_FUNC_END_ALIAS(x);		\
-		SYM_FUNC_END_ALIAS(__pi_##x)
+#define SYM_TYPED_FUNC_START(name)				\
+	SYM_TYPED_START(name, SYM_L_GLOBAL, SYM_A_ALIGN)	\
+	bti c ;
 
 #endif
diff --git a/arch/arm64/include/asm/lse.h b/arch/arm64/include/asm/lse.h
index 5d10051c3e62..c503db8e73b0 100644
--- a/arch/arm64/include/asm/lse.h
+++ b/arch/arm64/include/asm/lse.h
@@ -13,16 +13,13 @@
 #include <linux/jump_label.h>
 #include <linux/stringify.h>
 #include <asm/alternative.h>
+#include <asm/alternative-macros.h>
 #include <asm/atomic_lse.h>
 #include <asm/cpucaps.h>
 
-extern struct static_key_false cpu_hwcap_keys[ARM64_NCAPS];
-extern struct static_key_false arm64_const_caps_ready;
-
-static inline bool system_uses_lse_atomics(void)
+static __always_inline bool system_uses_lse_atomics(void)
 {
-	return (static_branch_likely(&arm64_const_caps_ready)) &&
-		static_branch_likely(&cpu_hwcap_keys[ARM64_HAS_LSE_ATOMICS]);
+	return alternative_has_feature_likely(ARM64_HAS_LSE_ATOMICS);
 }
 
 #define __lse_ll_sc_body(op, ...)					\
diff --git a/arch/arm64/include/asm/memory.h b/arch/arm64/include/asm/memory.h
index 1b9a1e242612..9dd08cd339c3 100644
--- a/arch/arm64/include/asm/memory.h
+++ b/arch/arm64/include/asm/memory.h
@@ -44,11 +44,8 @@
 #define _PAGE_OFFSET(va)	(-(UL(1) << (va)))
 #define PAGE_OFFSET		(_PAGE_OFFSET(VA_BITS))
 #define KIMAGE_VADDR		(MODULES_END)
-#define BPF_JIT_REGION_START	(_PAGE_END(VA_BITS_MIN))
-#define BPF_JIT_REGION_SIZE	(SZ_128M)
-#define BPF_JIT_REGION_END	(BPF_JIT_REGION_START + BPF_JIT_REGION_SIZE)
 #define MODULES_END		(MODULES_VADDR + MODULES_VSIZE)
-#define MODULES_VADDR		(BPF_JIT_REGION_END)
+#define MODULES_VADDR		(_PAGE_END(VA_BITS_MIN))
 #define MODULES_VSIZE		(SZ_128M)
 #define VMEMMAP_START		(-(UL(1) << (VA_BITS - VMEMMAP_SHIFT)))
 #define VMEMMAP_END		(VMEMMAP_START + VMEMMAP_SIZE)
@@ -117,6 +114,14 @@
 #define OVERFLOW_STACK_SIZE	SZ_4K
 
 /*
+ * With the minimum frame size of [x29, x30], exactly half the combined
+ * sizes of the hyp and overflow stacks is the maximum size needed to
+ * save the unwinded stacktrace; plus an additional entry to delimit the
+ * end.
+ */
+#define NVHE_STACKTRACE_SIZE	((OVERFLOW_STACK_SIZE + PAGE_SIZE) / 2 + sizeof(long))
+
+/*
  * Alignment of kernel segments (e.g. .text, .data).
  *
  *  4 KB granule:  16 level 3 entries, with contiguous bit
@@ -177,7 +182,11 @@
 #include <linux/types.h>
 #include <asm/bug.h>
 
+#if VA_BITS > 48
 extern u64			vabits_actual;
+#else
+#define vabits_actual		((u64)VA_BITS)
+#endif
 
 extern s64			memstart_addr;
 /* PHYS_OFFSET - the physical address of the start of memory. */
@@ -354,6 +363,11 @@ static inline void *phys_to_virt(phys_addr_t x)
 })
 
 void dump_mem_limit(void);
+
+static inline bool defer_reserve_crashkernel(void)
+{
+	return IS_ENABLED(CONFIG_ZONE_DMA) || IS_ENABLED(CONFIG_ZONE_DMA32);
+}
 #endif /* !ASSEMBLY */
 
 /*
@@ -367,6 +381,15 @@ void dump_mem_limit(void);
 # define INIT_MEMBLOCK_RESERVED_REGIONS	(INIT_MEMBLOCK_REGIONS + NR_CPUS + 1)
 #endif
 
+/*
+ * memory regions which marked with flag MEMBLOCK_NOMAP(for example, the memory
+ * of the EFI_UNUSABLE_MEMORY type) may divide a continuous memory block into
+ * multiple parts. As a result, the number of memory regions is large.
+ */
+#ifdef CONFIG_EFI
+#define INIT_MEMBLOCK_MEMORY_REGIONS	(INIT_MEMBLOCK_REGIONS * 8)
+#endif
+
 #include <asm-generic/memory_model.h>
 
 #endif /* __ASM_MEMORY_H */
diff --git a/arch/arm64/include/asm/mman.h b/arch/arm64/include/asm/mman.h
index e3e28f7daf62..5966ee4a6154 100644
--- a/arch/arm64/include/asm/mman.h
+++ b/arch/arm64/include/asm/mman.h
@@ -35,30 +35,6 @@ static inline unsigned long arch_calc_vm_flag_bits(unsigned long flags)
 }
 #define arch_calc_vm_flag_bits(flags) arch_calc_vm_flag_bits(flags)
 
-static inline pgprot_t arch_vm_get_page_prot(unsigned long vm_flags)
-{
-	pteval_t prot = 0;
-
-	if (vm_flags & VM_ARM64_BTI)
-		prot |= PTE_GP;
-
-	/*
-	 * There are two conditions required for returning a Normal Tagged
-	 * memory type: (1) the user requested it via PROT_MTE passed to
-	 * mmap() or mprotect() and (2) the corresponding vma supports MTE. We
-	 * register (1) as VM_MTE in the vma->vm_flags and (2) as
-	 * VM_MTE_ALLOWED. Note that the latter can only be set during the
-	 * mmap() call since mprotect() does not accept MAP_* flags.
-	 * Checking for VM_MTE only is sufficient since arch_validate_flags()
-	 * does not permit (VM_MTE & !VM_MTE_ALLOWED).
-	 */
-	if (vm_flags & VM_MTE)
-		prot |= PTE_ATTRINDX(MT_NORMAL_TAGGED);
-
-	return __pgprot(prot);
-}
-#define arch_vm_get_page_prot(vm_flags) arch_vm_get_page_prot(vm_flags)
-
 static inline bool arch_validate_prot(unsigned long prot,
 	unsigned long addr __always_unused)
 {
diff --git a/arch/arm64/include/asm/mmu.h b/arch/arm64/include/asm/mmu.h
index e9c30859f80c..48f8466a4be9 100644
--- a/arch/arm64/include/asm/mmu.h
+++ b/arch/arm64/include/asm/mmu.h
@@ -15,6 +15,7 @@
 #ifndef __ASSEMBLY__
 
 #include <linux/refcount.h>
+#include <asm/cpufeature.h>
 
 typedef struct {
 	atomic64_t	id;
diff --git a/arch/arm64/include/asm/mmu_context.h b/arch/arm64/include/asm/mmu_context.h
index 6770667b34a3..d3f8b5df0c1f 100644
--- a/arch/arm64/include/asm/mmu_context.h
+++ b/arch/arm64/include/asm/mmu_context.h
@@ -60,8 +60,7 @@ static inline void cpu_switch_mm(pgd_t *pgd, struct mm_struct *mm)
  * TCR_T0SZ(VA_BITS), unless system RAM is positioned very high in
  * physical memory, in which case it will be smaller.
  */
-extern u64 idmap_t0sz;
-extern u64 idmap_ptrs_per_pgd;
+extern int idmap_t0sz;
 
 /*
  * Ensure TCR.T0SZ is set to the provided value.
@@ -106,13 +105,18 @@ static inline void cpu_uninstall_idmap(void)
 		cpu_switch_mm(mm->pgd, mm);
 }
 
-static inline void cpu_install_idmap(void)
+static inline void __cpu_install_idmap(pgd_t *idmap)
 {
 	cpu_set_reserved_ttbr0();
 	local_flush_tlb_all();
 	cpu_set_idmap_tcr_t0sz();
 
-	cpu_switch_mm(lm_alias(idmap_pg_dir), &init_mm);
+	cpu_switch_mm(lm_alias(idmap), &init_mm);
+}
+
+static inline void cpu_install_idmap(void)
+{
+	__cpu_install_idmap(idmap_pg_dir);
 }
 
 /*
@@ -143,7 +147,7 @@ static inline void cpu_install_ttbr0(phys_addr_t ttbr0, unsigned long t0sz)
  * Atomically replaces the active TTBR1_EL1 PGD with a new VA-compatible PGD,
  * avoiding the possibility of conflicting TLB entries being allocated.
  */
-static inline void __nocfi cpu_replace_ttbr1(pgd_t *pgdp)
+static inline void cpu_replace_ttbr1(pgd_t *pgdp, pgd_t *idmap)
 {
 	typedef void (ttbr_replace_func)(phys_addr_t);
 	extern ttbr_replace_func idmap_cpu_replace_ttbr1;
@@ -164,9 +168,9 @@ static inline void __nocfi cpu_replace_ttbr1(pgd_t *pgdp)
 		ttbr1 |= TTBR_CNP_BIT;
 	}
 
-	replace_phys = (void *)__pa_symbol(function_nocfi(idmap_cpu_replace_ttbr1));
+	replace_phys = (void *)__pa_symbol(idmap_cpu_replace_ttbr1);
 
-	cpu_install_idmap();
+	__cpu_install_idmap(idmap);
 	replace_phys(ttbr1);
 	cpu_uninstall_idmap();
 }
diff --git a/arch/arm64/include/asm/module.h b/arch/arm64/include/asm/module.h
index 4e7fa2623896..18734fed3bdd 100644
--- a/arch/arm64/include/asm/module.h
+++ b/arch/arm64/include/asm/module.h
@@ -58,11 +58,20 @@ static inline bool is_forbidden_offset_for_adrp(void *place)
 }
 
 struct plt_entry get_plt_entry(u64 dst, void *pc);
-bool plt_entries_equal(const struct plt_entry *a, const struct plt_entry *b);
 
-static inline bool plt_entry_is_initialized(const struct plt_entry *e)
+static inline const Elf_Shdr *find_section(const Elf_Ehdr *hdr,
+				    const Elf_Shdr *sechdrs,
+				    const char *name)
 {
-	return e->adrp || e->add || e->br;
+	const Elf_Shdr *s, *se;
+	const char *secstrs = (void *)hdr + sechdrs[hdr->e_shstrndx].sh_offset;
+
+	for (s = sechdrs, se = sechdrs + hdr->e_shnum; s < se; s++) {
+		if (strcmp(name, secstrs + s->sh_name) == 0)
+			return s;
+	}
+
+	return NULL;
 }
 
 #endif /* __ASM_MODULE_H */
diff --git a/arch/arm64/include/asm/module.lds.h b/arch/arm64/include/asm/module.lds.h
index a11ccadd47d2..094701ec5500 100644
--- a/arch/arm64/include/asm/module.lds.h
+++ b/arch/arm64/include/asm/module.lds.h
@@ -1,8 +1,8 @@
 SECTIONS {
 #ifdef CONFIG_ARM64_MODULE_PLTS
-	.plt 0 (NOLOAD) : { BYTE(0) }
-	.init.plt 0 (NOLOAD) : { BYTE(0) }
-	.text.ftrace_trampoline 0 (NOLOAD) : { BYTE(0) }
+	.plt 0 : { BYTE(0) }
+	.init.plt 0 : { BYTE(0) }
+	.text.ftrace_trampoline 0 : { BYTE(0) }
 #endif
 
 #ifdef CONFIG_KASAN_SW_TAGS
diff --git a/arch/arm64/include/asm/mte-def.h b/arch/arm64/include/asm/mte-def.h
index 626d359b396e..14ee86b019c2 100644
--- a/arch/arm64/include/asm/mte-def.h
+++ b/arch/arm64/include/asm/mte-def.h
@@ -11,6 +11,7 @@
 #define MTE_TAG_SHIFT		56
 #define MTE_TAG_SIZE		4
 #define MTE_TAG_MASK		GENMASK((MTE_TAG_SHIFT + (MTE_TAG_SIZE - 1)), MTE_TAG_SHIFT)
+#define MTE_PAGE_TAG_STORAGE	(MTE_GRANULES_PER_PAGE * MTE_TAG_SIZE / 8)
 
 #define __MTE_PREAMBLE		ARM64_ASM_PREAMBLE ".arch_extension memtag\n"
 
diff --git a/arch/arm64/include/asm/mte-kasan.h b/arch/arm64/include/asm/mte-kasan.h
index 478b9bcf69ad..9f79425fc65a 100644
--- a/arch/arm64/include/asm/mte-kasan.h
+++ b/arch/arm64/include/asm/mte-kasan.h
@@ -5,6 +5,8 @@
 #ifndef __ASM_MTE_KASAN_H
 #define __ASM_MTE_KASAN_H
 
+#include <asm/compiler.h>
+#include <asm/cputype.h>
 #include <asm/mte-def.h>
 
 #ifndef __ASSEMBLY__
@@ -84,10 +86,12 @@ static inline void __dc_gzva(u64 p)
 static inline void mte_set_mem_tag_range(void *addr, size_t size, u8 tag,
 					 bool init)
 {
-	u64 curr, mask, dczid_bs, end1, end2, end3;
+	u64 curr, mask, dczid, dczid_bs, dczid_dzp, end1, end2, end3;
 
 	/* Read DC G(Z)VA block size from the system register. */
-	dczid_bs = 4ul << (read_cpuid(DCZID_EL0) & 0xf);
+	dczid = read_cpuid(DCZID_EL0);
+	dczid_bs = 4ul << (dczid & 0xf);
+	dczid_dzp = (dczid >> 4) & 1;
 
 	curr = (u64)__tag_set(addr, tag);
 	mask = dczid_bs - 1;
@@ -106,7 +110,7 @@ static inline void mte_set_mem_tag_range(void *addr, size_t size, u8 tag,
 	 */
 #define SET_MEMTAG_RANGE(stg_post, dc_gva)		\
 	do {						\
-		if (size >= 2 * dczid_bs) {		\
+		if (!dczid_dzp && size >= 2 * dczid_bs) {\
 			do {				\
 				curr = stg_post(curr);	\
 			} while (curr < end1);		\
diff --git a/arch/arm64/include/asm/mte.h b/arch/arm64/include/asm/mte.h
index 075539f5f1c8..760c62f8e22f 100644
--- a/arch/arm64/include/asm/mte.h
+++ b/arch/arm64/include/asm/mte.h
@@ -11,7 +11,9 @@
 #ifndef __ASSEMBLY__
 
 #include <linux/bitfield.h>
+#include <linux/kasan-enabled.h>
 #include <linux/page-flags.h>
+#include <linux/sched.h>
 #include <linux/types.h>
 
 #include <asm/pgtable-types.h>
@@ -40,11 +42,14 @@ void mte_sync_tags(pte_t old_pte, pte_t pte);
 void mte_copy_page_tags(void *kto, const void *kfrom);
 void mte_thread_init_user(void);
 void mte_thread_switch(struct task_struct *next);
+void mte_cpu_setup(void);
 void mte_suspend_enter(void);
+void mte_suspend_exit(void);
 long set_mte_ctrl(struct task_struct *task, unsigned long arg);
 long get_mte_ctrl(struct task_struct *task);
 int mte_ptrace_copy_tags(struct task_struct *child, long request,
 			 unsigned long addr, unsigned long data);
+size_t mte_probe_user_range(const char __user *uaddr, size_t size);
 
 #else /* CONFIG_ARM64_MTE */
 
@@ -69,6 +74,9 @@ static inline void mte_thread_switch(struct task_struct *next)
 static inline void mte_suspend_enter(void)
 {
 }
+static inline void mte_suspend_exit(void)
+{
+}
 static inline long set_mte_ctrl(struct task_struct *task, unsigned long arg)
 {
 	return 0;
@@ -86,6 +94,26 @@ static inline int mte_ptrace_copy_tags(struct task_struct *child,
 
 #endif /* CONFIG_ARM64_MTE */
 
+static inline void mte_disable_tco_entry(struct task_struct *task)
+{
+	if (!system_supports_mte())
+		return;
+
+	/*
+	 * Re-enable tag checking (TCO set on exception entry). This is only
+	 * necessary if MTE is enabled in either the kernel or the userspace
+	 * task in synchronous or asymmetric mode (SCTLR_EL1.TCF0 bit 0 is set
+	 * for both). With MTE disabled in the kernel and disabled or
+	 * asynchronous in userspace, tag check faults (including in uaccesses)
+	 * are not reported, therefore there is no need to re-enable checking.
+	 * This is beneficial on microarchitectures where re-enabling TCO is
+	 * expensive.
+	 */
+	if (kasan_hw_tags_enabled() ||
+	    (task->thread.sctlr_user & (1UL << SCTLR_EL1_TCF0_SHIFT)))
+		asm volatile(SET_PSTATE_TCO(0));
+}
+
 #ifdef CONFIG_KASAN_HW_TAGS
 /* Whether the MTE asynchronous mode is enabled. */
 DECLARE_STATIC_KEY_FALSE(mte_async_or_asymm_mode);
diff --git a/arch/arm64/include/asm/paravirt_api_clock.h b/arch/arm64/include/asm/paravirt_api_clock.h
new file mode 100644
index 000000000000..65ac7cee0dad
--- /dev/null
+++ b/arch/arm64/include/asm/paravirt_api_clock.h
@@ -0,0 +1 @@
+#include <asm/paravirt.h>
diff --git a/arch/arm64/include/asm/pci.h b/arch/arm64/include/asm/pci.h
index b33ca260e3c9..016eb6b46dc0 100644
--- a/arch/arm64/include/asm/pci.h
+++ b/arch/arm64/include/asm/pci.h
@@ -9,7 +9,6 @@
 #include <asm/io.h>
 
 #define PCIBIOS_MIN_IO		0x1000
-#define PCIBIOS_MIN_MEM		0
 
 /*
  * Set to 1 if the kernel should re-assign all PCI bus numbers
@@ -18,21 +17,8 @@
 	(pci_has_flag(PCI_REASSIGN_ALL_BUS))
 
 #define arch_can_pci_mmap_wc() 1
-#define ARCH_GENERIC_PCI_MMAP_RESOURCE	1
 
-extern int isa_dma_bridge_buggy;
-
-#ifdef CONFIG_PCI
-static inline int pci_get_legacy_ide_irq(struct pci_dev *dev, int channel)
-{
-	/* no legacy IRQ on arm64 */
-	return -ENODEV;
-}
-
-static inline int pci_proc_domain(struct pci_bus *bus)
-{
-	return 1;
-}
-#endif  /* CONFIG_PCI */
+/* Generic PCI */
+#include <asm-generic/pci.h>
 
 #endif  /* __ASM_PCI_H */
diff --git a/arch/arm64/include/asm/percpu.h b/arch/arm64/include/asm/percpu.h
index 8f1661603b78..b9ba19dbdb69 100644
--- a/arch/arm64/include/asm/percpu.h
+++ b/arch/arm64/include/asm/percpu.h
@@ -10,6 +10,7 @@
 #include <asm/alternative.h>
 #include <asm/cmpxchg.h>
 #include <asm/stack_pointer.h>
+#include <asm/sysreg.h>
 
 static inline void set_my_cpu_offset(unsigned long off)
 {
diff --git a/arch/arm64/include/asm/perf_event.h b/arch/arm64/include/asm/perf_event.h
index 4ef6f19331f9..3eaf462f5752 100644
--- a/arch/arm64/include/asm/perf_event.h
+++ b/arch/arm64/include/asm/perf_event.h
@@ -15,70 +15,70 @@
 /*
  * Common architectural and microarchitectural event numbers.
  */
-#define ARMV8_PMUV3_PERFCTR_SW_INCR				0x00
-#define ARMV8_PMUV3_PERFCTR_L1I_CACHE_REFILL			0x01
-#define ARMV8_PMUV3_PERFCTR_L1I_TLB_REFILL			0x02
-#define ARMV8_PMUV3_PERFCTR_L1D_CACHE_REFILL			0x03
-#define ARMV8_PMUV3_PERFCTR_L1D_CACHE				0x04
-#define ARMV8_PMUV3_PERFCTR_L1D_TLB_REFILL			0x05
-#define ARMV8_PMUV3_PERFCTR_LD_RETIRED				0x06
-#define ARMV8_PMUV3_PERFCTR_ST_RETIRED				0x07
-#define ARMV8_PMUV3_PERFCTR_INST_RETIRED			0x08
-#define ARMV8_PMUV3_PERFCTR_EXC_TAKEN				0x09
-#define ARMV8_PMUV3_PERFCTR_EXC_RETURN				0x0A
-#define ARMV8_PMUV3_PERFCTR_CID_WRITE_RETIRED			0x0B
-#define ARMV8_PMUV3_PERFCTR_PC_WRITE_RETIRED			0x0C
-#define ARMV8_PMUV3_PERFCTR_BR_IMMED_RETIRED			0x0D
-#define ARMV8_PMUV3_PERFCTR_BR_RETURN_RETIRED			0x0E
-#define ARMV8_PMUV3_PERFCTR_UNALIGNED_LDST_RETIRED		0x0F
-#define ARMV8_PMUV3_PERFCTR_BR_MIS_PRED				0x10
-#define ARMV8_PMUV3_PERFCTR_CPU_CYCLES				0x11
-#define ARMV8_PMUV3_PERFCTR_BR_PRED				0x12
-#define ARMV8_PMUV3_PERFCTR_MEM_ACCESS				0x13
-#define ARMV8_PMUV3_PERFCTR_L1I_CACHE				0x14
-#define ARMV8_PMUV3_PERFCTR_L1D_CACHE_WB			0x15
-#define ARMV8_PMUV3_PERFCTR_L2D_CACHE				0x16
-#define ARMV8_PMUV3_PERFCTR_L2D_CACHE_REFILL			0x17
-#define ARMV8_PMUV3_PERFCTR_L2D_CACHE_WB			0x18
-#define ARMV8_PMUV3_PERFCTR_BUS_ACCESS				0x19
-#define ARMV8_PMUV3_PERFCTR_MEMORY_ERROR			0x1A
-#define ARMV8_PMUV3_PERFCTR_INST_SPEC				0x1B
-#define ARMV8_PMUV3_PERFCTR_TTBR_WRITE_RETIRED			0x1C
-#define ARMV8_PMUV3_PERFCTR_BUS_CYCLES				0x1D
-#define ARMV8_PMUV3_PERFCTR_CHAIN				0x1E
-#define ARMV8_PMUV3_PERFCTR_L1D_CACHE_ALLOCATE			0x1F
-#define ARMV8_PMUV3_PERFCTR_L2D_CACHE_ALLOCATE			0x20
-#define ARMV8_PMUV3_PERFCTR_BR_RETIRED				0x21
-#define ARMV8_PMUV3_PERFCTR_BR_MIS_PRED_RETIRED			0x22
-#define ARMV8_PMUV3_PERFCTR_STALL_FRONTEND			0x23
-#define ARMV8_PMUV3_PERFCTR_STALL_BACKEND			0x24
-#define ARMV8_PMUV3_PERFCTR_L1D_TLB				0x25
-#define ARMV8_PMUV3_PERFCTR_L1I_TLB				0x26
-#define ARMV8_PMUV3_PERFCTR_L2I_CACHE				0x27
-#define ARMV8_PMUV3_PERFCTR_L2I_CACHE_REFILL			0x28
-#define ARMV8_PMUV3_PERFCTR_L3D_CACHE_ALLOCATE			0x29
-#define ARMV8_PMUV3_PERFCTR_L3D_CACHE_REFILL			0x2A
-#define ARMV8_PMUV3_PERFCTR_L3D_CACHE				0x2B
-#define ARMV8_PMUV3_PERFCTR_L3D_CACHE_WB			0x2C
-#define ARMV8_PMUV3_PERFCTR_L2D_TLB_REFILL			0x2D
-#define ARMV8_PMUV3_PERFCTR_L2I_TLB_REFILL			0x2E
-#define ARMV8_PMUV3_PERFCTR_L2D_TLB				0x2F
-#define ARMV8_PMUV3_PERFCTR_L2I_TLB				0x30
-#define ARMV8_PMUV3_PERFCTR_REMOTE_ACCESS			0x31
-#define ARMV8_PMUV3_PERFCTR_LL_CACHE				0x32
-#define ARMV8_PMUV3_PERFCTR_LL_CACHE_MISS			0x33
-#define ARMV8_PMUV3_PERFCTR_DTLB_WALK				0x34
-#define ARMV8_PMUV3_PERFCTR_ITLB_WALK				0x35
-#define ARMV8_PMUV3_PERFCTR_LL_CACHE_RD				0x36
-#define ARMV8_PMUV3_PERFCTR_LL_CACHE_MISS_RD			0x37
-#define ARMV8_PMUV3_PERFCTR_REMOTE_ACCESS_RD			0x38
-#define ARMV8_PMUV3_PERFCTR_L1D_CACHE_LMISS_RD			0x39
-#define ARMV8_PMUV3_PERFCTR_OP_RETIRED				0x3A
-#define ARMV8_PMUV3_PERFCTR_OP_SPEC				0x3B
-#define ARMV8_PMUV3_PERFCTR_STALL				0x3C
-#define ARMV8_PMUV3_PERFCTR_STALL_SLOT_BACKEND			0x3D
-#define ARMV8_PMUV3_PERFCTR_STALL_SLOT_FRONTEND			0x3E
-#define ARMV8_PMUV3_PERFCTR_STALL_SLOT				0x3F
+#define ARMV8_PMUV3_PERFCTR_SW_INCR				0x0000
+#define ARMV8_PMUV3_PERFCTR_L1I_CACHE_REFILL			0x0001
+#define ARMV8_PMUV3_PERFCTR_L1I_TLB_REFILL			0x0002
+#define ARMV8_PMUV3_PERFCTR_L1D_CACHE_REFILL			0x0003
+#define ARMV8_PMUV3_PERFCTR_L1D_CACHE				0x0004
+#define ARMV8_PMUV3_PERFCTR_L1D_TLB_REFILL			0x0005
+#define ARMV8_PMUV3_PERFCTR_LD_RETIRED				0x0006
+#define ARMV8_PMUV3_PERFCTR_ST_RETIRED				0x0007
+#define ARMV8_PMUV3_PERFCTR_INST_RETIRED			0x0008
+#define ARMV8_PMUV3_PERFCTR_EXC_TAKEN				0x0009
+#define ARMV8_PMUV3_PERFCTR_EXC_RETURN				0x000A
+#define ARMV8_PMUV3_PERFCTR_CID_WRITE_RETIRED			0x000B
+#define ARMV8_PMUV3_PERFCTR_PC_WRITE_RETIRED			0x000C
+#define ARMV8_PMUV3_PERFCTR_BR_IMMED_RETIRED			0x000D
+#define ARMV8_PMUV3_PERFCTR_BR_RETURN_RETIRED			0x000E
+#define ARMV8_PMUV3_PERFCTR_UNALIGNED_LDST_RETIRED		0x000F
+#define ARMV8_PMUV3_PERFCTR_BR_MIS_PRED				0x0010
+#define ARMV8_PMUV3_PERFCTR_CPU_CYCLES				0x0011
+#define ARMV8_PMUV3_PERFCTR_BR_PRED				0x0012
+#define ARMV8_PMUV3_PERFCTR_MEM_ACCESS				0x0013
+#define ARMV8_PMUV3_PERFCTR_L1I_CACHE				0x0014
+#define ARMV8_PMUV3_PERFCTR_L1D_CACHE_WB			0x0015
+#define ARMV8_PMUV3_PERFCTR_L2D_CACHE				0x0016
+#define ARMV8_PMUV3_PERFCTR_L2D_CACHE_REFILL			0x0017
+#define ARMV8_PMUV3_PERFCTR_L2D_CACHE_WB			0x0018
+#define ARMV8_PMUV3_PERFCTR_BUS_ACCESS				0x0019
+#define ARMV8_PMUV3_PERFCTR_MEMORY_ERROR			0x001A
+#define ARMV8_PMUV3_PERFCTR_INST_SPEC				0x001B
+#define ARMV8_PMUV3_PERFCTR_TTBR_WRITE_RETIRED			0x001C
+#define ARMV8_PMUV3_PERFCTR_BUS_CYCLES				0x001D
+#define ARMV8_PMUV3_PERFCTR_CHAIN				0x001E
+#define ARMV8_PMUV3_PERFCTR_L1D_CACHE_ALLOCATE			0x001F
+#define ARMV8_PMUV3_PERFCTR_L2D_CACHE_ALLOCATE			0x0020
+#define ARMV8_PMUV3_PERFCTR_BR_RETIRED				0x0021
+#define ARMV8_PMUV3_PERFCTR_BR_MIS_PRED_RETIRED			0x0022
+#define ARMV8_PMUV3_PERFCTR_STALL_FRONTEND			0x0023
+#define ARMV8_PMUV3_PERFCTR_STALL_BACKEND			0x0024
+#define ARMV8_PMUV3_PERFCTR_L1D_TLB				0x0025
+#define ARMV8_PMUV3_PERFCTR_L1I_TLB				0x0026
+#define ARMV8_PMUV3_PERFCTR_L2I_CACHE				0x0027
+#define ARMV8_PMUV3_PERFCTR_L2I_CACHE_REFILL			0x0028
+#define ARMV8_PMUV3_PERFCTR_L3D_CACHE_ALLOCATE			0x0029
+#define ARMV8_PMUV3_PERFCTR_L3D_CACHE_REFILL			0x002A
+#define ARMV8_PMUV3_PERFCTR_L3D_CACHE				0x002B
+#define ARMV8_PMUV3_PERFCTR_L3D_CACHE_WB			0x002C
+#define ARMV8_PMUV3_PERFCTR_L2D_TLB_REFILL			0x002D
+#define ARMV8_PMUV3_PERFCTR_L2I_TLB_REFILL			0x002E
+#define ARMV8_PMUV3_PERFCTR_L2D_TLB				0x002F
+#define ARMV8_PMUV3_PERFCTR_L2I_TLB				0x0030
+#define ARMV8_PMUV3_PERFCTR_REMOTE_ACCESS			0x0031
+#define ARMV8_PMUV3_PERFCTR_LL_CACHE				0x0032
+#define ARMV8_PMUV3_PERFCTR_LL_CACHE_MISS			0x0033
+#define ARMV8_PMUV3_PERFCTR_DTLB_WALK				0x0034
+#define ARMV8_PMUV3_PERFCTR_ITLB_WALK				0x0035
+#define ARMV8_PMUV3_PERFCTR_LL_CACHE_RD				0x0036
+#define ARMV8_PMUV3_PERFCTR_LL_CACHE_MISS_RD			0x0037
+#define ARMV8_PMUV3_PERFCTR_REMOTE_ACCESS_RD			0x0038
+#define ARMV8_PMUV3_PERFCTR_L1D_CACHE_LMISS_RD			0x0039
+#define ARMV8_PMUV3_PERFCTR_OP_RETIRED				0x003A
+#define ARMV8_PMUV3_PERFCTR_OP_SPEC				0x003B
+#define ARMV8_PMUV3_PERFCTR_STALL				0x003C
+#define ARMV8_PMUV3_PERFCTR_STALL_SLOT_BACKEND			0x003D
+#define ARMV8_PMUV3_PERFCTR_STALL_SLOT_FRONTEND			0x003E
+#define ARMV8_PMUV3_PERFCTR_STALL_SLOT				0x003F
 
 /* Statistical profiling extension microarchitectural events */
 #define	ARMV8_SPE_PERFCTR_SAMPLE_POP				0x4000
@@ -96,6 +96,20 @@
 #define	ARMV8_PMUV3_PERFCTR_L2I_CACHE_LMISS			0x400A
 #define	ARMV8_PMUV3_PERFCTR_L3D_CACHE_LMISS_RD			0x400B
 
+/* Trace buffer events */
+#define ARMV8_PMUV3_PERFCTR_TRB_WRAP				0x400C
+#define ARMV8_PMUV3_PERFCTR_TRB_TRIG				0x400E
+
+/* Trace unit events */
+#define ARMV8_PMUV3_PERFCTR_TRCEXTOUT0				0x4010
+#define ARMV8_PMUV3_PERFCTR_TRCEXTOUT1				0x4011
+#define ARMV8_PMUV3_PERFCTR_TRCEXTOUT2				0x4012
+#define ARMV8_PMUV3_PERFCTR_TRCEXTOUT3				0x4013
+#define ARMV8_PMUV3_PERFCTR_CTI_TRIGOUT4			0x4018
+#define ARMV8_PMUV3_PERFCTR_CTI_TRIGOUT5			0x4019
+#define ARMV8_PMUV3_PERFCTR_CTI_TRIGOUT6			0x401A
+#define ARMV8_PMUV3_PERFCTR_CTI_TRIGOUT7			0x401B
+
 /* additional latency from alignment events */
 #define	ARMV8_PMUV3_PERFCTR_LDST_ALIGN_LAT			0x4020
 #define	ARMV8_PMUV3_PERFCTR_LD_ALIGN_LAT			0x4021
@@ -107,91 +121,91 @@
 #define	ARMV8_MTE_PERFCTR_MEM_ACCESS_CHECKED_WR			0x4026
 
 /* ARMv8 recommended implementation defined event types */
-#define ARMV8_IMPDEF_PERFCTR_L1D_CACHE_RD			0x40
-#define ARMV8_IMPDEF_PERFCTR_L1D_CACHE_WR			0x41
-#define ARMV8_IMPDEF_PERFCTR_L1D_CACHE_REFILL_RD		0x42
-#define ARMV8_IMPDEF_PERFCTR_L1D_CACHE_REFILL_WR		0x43
-#define ARMV8_IMPDEF_PERFCTR_L1D_CACHE_REFILL_INNER		0x44
-#define ARMV8_IMPDEF_PERFCTR_L1D_CACHE_REFILL_OUTER		0x45
-#define ARMV8_IMPDEF_PERFCTR_L1D_CACHE_WB_VICTIM		0x46
-#define ARMV8_IMPDEF_PERFCTR_L1D_CACHE_WB_CLEAN			0x47
-#define ARMV8_IMPDEF_PERFCTR_L1D_CACHE_INVAL			0x48
-
-#define ARMV8_IMPDEF_PERFCTR_L1D_TLB_REFILL_RD			0x4C
-#define ARMV8_IMPDEF_PERFCTR_L1D_TLB_REFILL_WR			0x4D
-#define ARMV8_IMPDEF_PERFCTR_L1D_TLB_RD				0x4E
-#define ARMV8_IMPDEF_PERFCTR_L1D_TLB_WR				0x4F
-#define ARMV8_IMPDEF_PERFCTR_L2D_CACHE_RD			0x50
-#define ARMV8_IMPDEF_PERFCTR_L2D_CACHE_WR			0x51
-#define ARMV8_IMPDEF_PERFCTR_L2D_CACHE_REFILL_RD		0x52
-#define ARMV8_IMPDEF_PERFCTR_L2D_CACHE_REFILL_WR		0x53
-
-#define ARMV8_IMPDEF_PERFCTR_L2D_CACHE_WB_VICTIM		0x56
-#define ARMV8_IMPDEF_PERFCTR_L2D_CACHE_WB_CLEAN			0x57
-#define ARMV8_IMPDEF_PERFCTR_L2D_CACHE_INVAL			0x58
-
-#define ARMV8_IMPDEF_PERFCTR_L2D_TLB_REFILL_RD			0x5C
-#define ARMV8_IMPDEF_PERFCTR_L2D_TLB_REFILL_WR			0x5D
-#define ARMV8_IMPDEF_PERFCTR_L2D_TLB_RD				0x5E
-#define ARMV8_IMPDEF_PERFCTR_L2D_TLB_WR				0x5F
-#define ARMV8_IMPDEF_PERFCTR_BUS_ACCESS_RD			0x60
-#define ARMV8_IMPDEF_PERFCTR_BUS_ACCESS_WR			0x61
-#define ARMV8_IMPDEF_PERFCTR_BUS_ACCESS_SHARED			0x62
-#define ARMV8_IMPDEF_PERFCTR_BUS_ACCESS_NOT_SHARED		0x63
-#define ARMV8_IMPDEF_PERFCTR_BUS_ACCESS_NORMAL			0x64
-#define ARMV8_IMPDEF_PERFCTR_BUS_ACCESS_PERIPH			0x65
-#define ARMV8_IMPDEF_PERFCTR_MEM_ACCESS_RD			0x66
-#define ARMV8_IMPDEF_PERFCTR_MEM_ACCESS_WR			0x67
-#define ARMV8_IMPDEF_PERFCTR_UNALIGNED_LD_SPEC			0x68
-#define ARMV8_IMPDEF_PERFCTR_UNALIGNED_ST_SPEC			0x69
-#define ARMV8_IMPDEF_PERFCTR_UNALIGNED_LDST_SPEC		0x6A
-
-#define ARMV8_IMPDEF_PERFCTR_LDREX_SPEC				0x6C
-#define ARMV8_IMPDEF_PERFCTR_STREX_PASS_SPEC			0x6D
-#define ARMV8_IMPDEF_PERFCTR_STREX_FAIL_SPEC			0x6E
-#define ARMV8_IMPDEF_PERFCTR_STREX_SPEC				0x6F
-#define ARMV8_IMPDEF_PERFCTR_LD_SPEC				0x70
-#define ARMV8_IMPDEF_PERFCTR_ST_SPEC				0x71
-#define ARMV8_IMPDEF_PERFCTR_LDST_SPEC				0x72
-#define ARMV8_IMPDEF_PERFCTR_DP_SPEC				0x73
-#define ARMV8_IMPDEF_PERFCTR_ASE_SPEC				0x74
-#define ARMV8_IMPDEF_PERFCTR_VFP_SPEC				0x75
-#define ARMV8_IMPDEF_PERFCTR_PC_WRITE_SPEC			0x76
-#define ARMV8_IMPDEF_PERFCTR_CRYPTO_SPEC			0x77
-#define ARMV8_IMPDEF_PERFCTR_BR_IMMED_SPEC			0x78
-#define ARMV8_IMPDEF_PERFCTR_BR_RETURN_SPEC			0x79
-#define ARMV8_IMPDEF_PERFCTR_BR_INDIRECT_SPEC			0x7A
-
-#define ARMV8_IMPDEF_PERFCTR_ISB_SPEC				0x7C
-#define ARMV8_IMPDEF_PERFCTR_DSB_SPEC				0x7D
-#define ARMV8_IMPDEF_PERFCTR_DMB_SPEC				0x7E
-
-#define ARMV8_IMPDEF_PERFCTR_EXC_UNDEF				0x81
-#define ARMV8_IMPDEF_PERFCTR_EXC_SVC				0x82
-#define ARMV8_IMPDEF_PERFCTR_EXC_PABORT				0x83
-#define ARMV8_IMPDEF_PERFCTR_EXC_DABORT				0x84
-
-#define ARMV8_IMPDEF_PERFCTR_EXC_IRQ				0x86
-#define ARMV8_IMPDEF_PERFCTR_EXC_FIQ				0x87
-#define ARMV8_IMPDEF_PERFCTR_EXC_SMC				0x88
-
-#define ARMV8_IMPDEF_PERFCTR_EXC_HVC				0x8A
-#define ARMV8_IMPDEF_PERFCTR_EXC_TRAP_PABORT			0x8B
-#define ARMV8_IMPDEF_PERFCTR_EXC_TRAP_DABORT			0x8C
-#define ARMV8_IMPDEF_PERFCTR_EXC_TRAP_OTHER			0x8D
-#define ARMV8_IMPDEF_PERFCTR_EXC_TRAP_IRQ			0x8E
-#define ARMV8_IMPDEF_PERFCTR_EXC_TRAP_FIQ			0x8F
-#define ARMV8_IMPDEF_PERFCTR_RC_LD_SPEC				0x90
-#define ARMV8_IMPDEF_PERFCTR_RC_ST_SPEC				0x91
-
-#define ARMV8_IMPDEF_PERFCTR_L3D_CACHE_RD			0xA0
-#define ARMV8_IMPDEF_PERFCTR_L3D_CACHE_WR			0xA1
-#define ARMV8_IMPDEF_PERFCTR_L3D_CACHE_REFILL_RD		0xA2
-#define ARMV8_IMPDEF_PERFCTR_L3D_CACHE_REFILL_WR		0xA3
-
-#define ARMV8_IMPDEF_PERFCTR_L3D_CACHE_WB_VICTIM		0xA6
-#define ARMV8_IMPDEF_PERFCTR_L3D_CACHE_WB_CLEAN			0xA7
-#define ARMV8_IMPDEF_PERFCTR_L3D_CACHE_INVAL			0xA8
+#define ARMV8_IMPDEF_PERFCTR_L1D_CACHE_RD			0x0040
+#define ARMV8_IMPDEF_PERFCTR_L1D_CACHE_WR			0x0041
+#define ARMV8_IMPDEF_PERFCTR_L1D_CACHE_REFILL_RD		0x0042
+#define ARMV8_IMPDEF_PERFCTR_L1D_CACHE_REFILL_WR		0x0043
+#define ARMV8_IMPDEF_PERFCTR_L1D_CACHE_REFILL_INNER		0x0044
+#define ARMV8_IMPDEF_PERFCTR_L1D_CACHE_REFILL_OUTER		0x0045
+#define ARMV8_IMPDEF_PERFCTR_L1D_CACHE_WB_VICTIM		0x0046
+#define ARMV8_IMPDEF_PERFCTR_L1D_CACHE_WB_CLEAN			0x0047
+#define ARMV8_IMPDEF_PERFCTR_L1D_CACHE_INVAL			0x0048
+
+#define ARMV8_IMPDEF_PERFCTR_L1D_TLB_REFILL_RD			0x004C
+#define ARMV8_IMPDEF_PERFCTR_L1D_TLB_REFILL_WR			0x004D
+#define ARMV8_IMPDEF_PERFCTR_L1D_TLB_RD				0x004E
+#define ARMV8_IMPDEF_PERFCTR_L1D_TLB_WR				0x004F
+#define ARMV8_IMPDEF_PERFCTR_L2D_CACHE_RD			0x0050
+#define ARMV8_IMPDEF_PERFCTR_L2D_CACHE_WR			0x0051
+#define ARMV8_IMPDEF_PERFCTR_L2D_CACHE_REFILL_RD		0x0052
+#define ARMV8_IMPDEF_PERFCTR_L2D_CACHE_REFILL_WR		0x0053
+
+#define ARMV8_IMPDEF_PERFCTR_L2D_CACHE_WB_VICTIM		0x0056
+#define ARMV8_IMPDEF_PERFCTR_L2D_CACHE_WB_CLEAN			0x0057
+#define ARMV8_IMPDEF_PERFCTR_L2D_CACHE_INVAL			0x0058
+
+#define ARMV8_IMPDEF_PERFCTR_L2D_TLB_REFILL_RD			0x005C
+#define ARMV8_IMPDEF_PERFCTR_L2D_TLB_REFILL_WR			0x005D
+#define ARMV8_IMPDEF_PERFCTR_L2D_TLB_RD				0x005E
+#define ARMV8_IMPDEF_PERFCTR_L2D_TLB_WR				0x005F
+#define ARMV8_IMPDEF_PERFCTR_BUS_ACCESS_RD			0x0060
+#define ARMV8_IMPDEF_PERFCTR_BUS_ACCESS_WR			0x0061
+#define ARMV8_IMPDEF_PERFCTR_BUS_ACCESS_SHARED			0x0062
+#define ARMV8_IMPDEF_PERFCTR_BUS_ACCESS_NOT_SHARED		0x0063
+#define ARMV8_IMPDEF_PERFCTR_BUS_ACCESS_NORMAL			0x0064
+#define ARMV8_IMPDEF_PERFCTR_BUS_ACCESS_PERIPH			0x0065
+#define ARMV8_IMPDEF_PERFCTR_MEM_ACCESS_RD			0x0066
+#define ARMV8_IMPDEF_PERFCTR_MEM_ACCESS_WR			0x0067
+#define ARMV8_IMPDEF_PERFCTR_UNALIGNED_LD_SPEC			0x0068
+#define ARMV8_IMPDEF_PERFCTR_UNALIGNED_ST_SPEC			0x0069
+#define ARMV8_IMPDEF_PERFCTR_UNALIGNED_LDST_SPEC		0x006A
+
+#define ARMV8_IMPDEF_PERFCTR_LDREX_SPEC				0x006C
+#define ARMV8_IMPDEF_PERFCTR_STREX_PASS_SPEC			0x006D
+#define ARMV8_IMPDEF_PERFCTR_STREX_FAIL_SPEC			0x006E
+#define ARMV8_IMPDEF_PERFCTR_STREX_SPEC				0x006F
+#define ARMV8_IMPDEF_PERFCTR_LD_SPEC				0x0070
+#define ARMV8_IMPDEF_PERFCTR_ST_SPEC				0x0071
+#define ARMV8_IMPDEF_PERFCTR_LDST_SPEC				0x0072
+#define ARMV8_IMPDEF_PERFCTR_DP_SPEC				0x0073
+#define ARMV8_IMPDEF_PERFCTR_ASE_SPEC				0x0074
+#define ARMV8_IMPDEF_PERFCTR_VFP_SPEC				0x0075
+#define ARMV8_IMPDEF_PERFCTR_PC_WRITE_SPEC			0x0076
+#define ARMV8_IMPDEF_PERFCTR_CRYPTO_SPEC			0x0077
+#define ARMV8_IMPDEF_PERFCTR_BR_IMMED_SPEC			0x0078
+#define ARMV8_IMPDEF_PERFCTR_BR_RETURN_SPEC			0x0079
+#define ARMV8_IMPDEF_PERFCTR_BR_INDIRECT_SPEC			0x007A
+
+#define ARMV8_IMPDEF_PERFCTR_ISB_SPEC				0x007C
+#define ARMV8_IMPDEF_PERFCTR_DSB_SPEC				0x007D
+#define ARMV8_IMPDEF_PERFCTR_DMB_SPEC				0x007E
+
+#define ARMV8_IMPDEF_PERFCTR_EXC_UNDEF				0x0081
+#define ARMV8_IMPDEF_PERFCTR_EXC_SVC				0x0082
+#define ARMV8_IMPDEF_PERFCTR_EXC_PABORT				0x0083
+#define ARMV8_IMPDEF_PERFCTR_EXC_DABORT				0x0084
+
+#define ARMV8_IMPDEF_PERFCTR_EXC_IRQ				0x0086
+#define ARMV8_IMPDEF_PERFCTR_EXC_FIQ				0x0087
+#define ARMV8_IMPDEF_PERFCTR_EXC_SMC				0x0088
+
+#define ARMV8_IMPDEF_PERFCTR_EXC_HVC				0x008A
+#define ARMV8_IMPDEF_PERFCTR_EXC_TRAP_PABORT			0x008B
+#define ARMV8_IMPDEF_PERFCTR_EXC_TRAP_DABORT			0x008C
+#define ARMV8_IMPDEF_PERFCTR_EXC_TRAP_OTHER			0x008D
+#define ARMV8_IMPDEF_PERFCTR_EXC_TRAP_IRQ			0x008E
+#define ARMV8_IMPDEF_PERFCTR_EXC_TRAP_FIQ			0x008F
+#define ARMV8_IMPDEF_PERFCTR_RC_LD_SPEC				0x0090
+#define ARMV8_IMPDEF_PERFCTR_RC_ST_SPEC				0x0091
+
+#define ARMV8_IMPDEF_PERFCTR_L3D_CACHE_RD			0x00A0
+#define ARMV8_IMPDEF_PERFCTR_L3D_CACHE_WR			0x00A1
+#define ARMV8_IMPDEF_PERFCTR_L3D_CACHE_REFILL_RD		0x00A2
+#define ARMV8_IMPDEF_PERFCTR_L3D_CACHE_REFILL_WR		0x00A3
+
+#define ARMV8_IMPDEF_PERFCTR_L3D_CACHE_WB_VICTIM		0x00A6
+#define ARMV8_IMPDEF_PERFCTR_L3D_CACHE_WB_CLEAN			0x00A7
+#define ARMV8_IMPDEF_PERFCTR_L3D_CACHE_INVAL			0x00A8
 
 /*
  * Per-CPU PMCR: config reg
diff --git a/arch/arm64/include/asm/pgtable-hwdef.h b/arch/arm64/include/asm/pgtable-hwdef.h
index 40085e53f573..5ab8d163198f 100644
--- a/arch/arm64/include/asm/pgtable-hwdef.h
+++ b/arch/arm64/include/asm/pgtable-hwdef.h
@@ -49,7 +49,7 @@
 #define PMD_SHIFT		ARM64_HW_PGTABLE_LEVEL_SHIFT(2)
 #define PMD_SIZE		(_AC(1, UL) << PMD_SHIFT)
 #define PMD_MASK		(~(PMD_SIZE-1))
-#define PTRS_PER_PMD		PTRS_PER_PTE
+#define PTRS_PER_PMD		(1 << (PAGE_SHIFT - 3))
 #endif
 
 /*
@@ -59,7 +59,7 @@
 #define PUD_SHIFT		ARM64_HW_PGTABLE_LEVEL_SHIFT(1)
 #define PUD_SIZE		(_AC(1, UL) << PUD_SHIFT)
 #define PUD_MASK		(~(PUD_SIZE-1))
-#define PTRS_PER_PUD		PTRS_PER_PTE
+#define PTRS_PER_PUD		(1 << (PAGE_SHIFT - 3))
 #endif
 
 /*
@@ -273,16 +273,17 @@
 #define TCR_NFD1		(UL(1) << 54)
 #define TCR_E0PD0		(UL(1) << 55)
 #define TCR_E0PD1		(UL(1) << 56)
+#define TCR_TCMA0		(UL(1) << 57)
+#define TCR_TCMA1		(UL(1) << 58)
 
 /*
  * TTBR.
  */
 #ifdef CONFIG_ARM64_PA_BITS_52
 /*
- * This should be GENMASK_ULL(47, 2).
  * TTBR_ELx[1] is RES0 in this configuration.
  */
-#define TTBR_BADDR_MASK_52	(((UL(1) << 46) - 1) << 2)
+#define TTBR_BADDR_MASK_52	GENMASK_ULL(47, 2)
 #endif
 
 #ifdef CONFIG_ARM64_VA_BITS_52
diff --git a/arch/arm64/include/asm/pgtable-prot.h b/arch/arm64/include/asm/pgtable-prot.h
index 7032f04c8ac6..9b165117a454 100644
--- a/arch/arm64/include/asm/pgtable-prot.h
+++ b/arch/arm64/include/asm/pgtable-prot.h
@@ -14,6 +14,7 @@
  * Software defined PTE bits definition.
  */
 #define PTE_WRITE		(PTE_DBM)		 /* same as DBM (51) */
+#define PTE_SWP_EXCLUSIVE	(_AT(pteval_t, 1) << 2)	 /* only for swp ptes */
 #define PTE_DIRTY		(_AT(pteval_t, 1) << 55)
 #define PTE_SPECIAL		(_AT(pteval_t, 1) << 56)
 #define PTE_DEVMAP		(_AT(pteval_t, 1) << 57)
@@ -88,24 +89,6 @@ extern bool arm64_use_ng_mappings;
 #define PAGE_READONLY_EXEC	__pgprot(_PAGE_DEFAULT | PTE_USER | PTE_RDONLY | PTE_NG | PTE_PXN)
 #define PAGE_EXECONLY		__pgprot(_PAGE_DEFAULT | PTE_RDONLY | PTE_NG | PTE_PXN)
 
-#define __P000  PAGE_NONE
-#define __P001  PAGE_READONLY
-#define __P010  PAGE_READONLY
-#define __P011  PAGE_READONLY
-#define __P100  PAGE_EXECONLY
-#define __P101  PAGE_READONLY_EXEC
-#define __P110  PAGE_READONLY_EXEC
-#define __P111  PAGE_READONLY_EXEC
-
-#define __S000  PAGE_NONE
-#define __S001  PAGE_READONLY
-#define __S010  PAGE_SHARED
-#define __S011  PAGE_SHARED
-#define __S100  PAGE_EXECONLY
-#define __S101  PAGE_READONLY_EXEC
-#define __S110  PAGE_SHARED_EXEC
-#define __S111  PAGE_SHARED_EXEC
-
 #endif /* __ASSEMBLY__ */
 
 #endif /* __ASM_PGTABLE_PROT_H */
diff --git a/arch/arm64/include/asm/pgtable.h b/arch/arm64/include/asm/pgtable.h
index c4ba047a82d2..71a1af42f0e8 100644
--- a/arch/arm64/include/asm/pgtable.h
+++ b/arch/arm64/include/asm/pgtable.h
@@ -33,6 +33,7 @@
 #include <linux/mmdebug.h>
 #include <linux/mm_types.h>
 #include <linux/sched.h>
+#include <linux/page_table_check.h>
 
 #ifdef CONFIG_TRANSPARENT_HUGEPAGE
 #define __HAVE_ARCH_FLUSH_PMD_TLB_RANGE
@@ -44,6 +45,12 @@
 	__flush_tlb_range(vma, addr, end, PUD_SIZE, false, 1)
 #endif /* CONFIG_TRANSPARENT_HUGEPAGE */
 
+static inline bool arch_thp_swp_supported(void)
+{
+	return !system_supports_mte();
+}
+#define arch_thp_swp_supported arch_thp_swp_supported
+
 /*
  * Outside of a few very special situations (e.g. hibernation), we always
  * use broadcast TLB invalidation instructions, therefore a spurious page
@@ -96,6 +103,7 @@ static inline pteval_t __phys_to_pte_val(phys_addr_t phys)
 #define pte_young(pte)		(!!(pte_val(pte) & PTE_AF))
 #define pte_special(pte)	(!!(pte_val(pte) & PTE_SPECIAL))
 #define pte_write(pte)		(!!(pte_val(pte) & PTE_WRITE))
+#define pte_user(pte)		(!!(pte_val(pte) & PTE_USER))
 #define pte_user_exec(pte)	(!(pte_val(pte) & PTE_UXN))
 #define pte_cont(pte)		(!!(pte_val(pte) & PTE_CONT))
 #define pte_devmap(pte)		(!!(pte_val(pte) & PTE_DEVMAP))
@@ -312,8 +320,8 @@ static inline void __check_racy_pte_update(struct mm_struct *mm, pte_t *ptep,
 		     __func__, pte_val(old_pte), pte_val(pte));
 }
 
-static inline void set_pte_at(struct mm_struct *mm, unsigned long addr,
-			      pte_t *ptep, pte_t pte)
+static inline void __set_pte_at(struct mm_struct *mm, unsigned long addr,
+				pte_t *ptep, pte_t pte)
 {
 	if (pte_present(pte) && pte_user_exec(pte) && !pte_special(pte))
 		__sync_icache_dcache(pte);
@@ -343,6 +351,13 @@ static inline void set_pte_at(struct mm_struct *mm, unsigned long addr,
 	set_pte(ptep, pte);
 }
 
+static inline void set_pte_at(struct mm_struct *mm, unsigned long addr,
+			      pte_t *ptep, pte_t pte)
+{
+	page_table_check_pte_set(mm, addr, ptep, pte);
+	return __set_pte_at(mm, addr, ptep, pte);
+}
+
 /*
  * Huge pte definitions.
  */
@@ -402,6 +417,32 @@ static inline pgprot_t mk_pmd_sect_prot(pgprot_t prot)
 	return __pgprot((pgprot_val(prot) & ~PMD_TABLE_BIT) | PMD_TYPE_SECT);
 }
 
+#define __HAVE_ARCH_PTE_SWP_EXCLUSIVE
+static inline pte_t pte_swp_mkexclusive(pte_t pte)
+{
+	return set_pte_bit(pte, __pgprot(PTE_SWP_EXCLUSIVE));
+}
+
+static inline int pte_swp_exclusive(pte_t pte)
+{
+	return pte_val(pte) & PTE_SWP_EXCLUSIVE;
+}
+
+static inline pte_t pte_swp_clear_exclusive(pte_t pte)
+{
+	return clear_pte_bit(pte, __pgprot(PTE_SWP_EXCLUSIVE));
+}
+
+/*
+ * Select all bits except the pfn
+ */
+static inline pgprot_t pte_pgprot(pte_t pte)
+{
+	unsigned long pfn = pte_pfn(pte);
+
+	return __pgprot(pte_val(pfn_pte(pfn, __pgprot(0))) ^ pte_val(pte));
+}
+
 #ifdef CONFIG_NUMA_BALANCING
 /*
  * See the comment in include/linux/pgtable.h
@@ -438,6 +479,8 @@ static inline int pmd_trans_huge(pmd_t pmd)
 #define pmd_dirty(pmd)		pte_dirty(pmd_pte(pmd))
 #define pmd_young(pmd)		pte_young(pmd_pte(pmd))
 #define pmd_valid(pmd)		pte_valid(pmd_pte(pmd))
+#define pmd_user(pmd)		pte_user(pmd_pte(pmd))
+#define pmd_user_exec(pmd)	pte_user_exec(pmd_pte(pmd))
 #define pmd_cont(pmd)		pte_cont(pmd_pte(pmd))
 #define pmd_wrprotect(pmd)	pte_pmd(pte_wrprotect(pmd_pte(pmd)))
 #define pmd_mkold(pmd)		pte_pmd(pte_mkold(pmd_pte(pmd)))
@@ -485,8 +528,19 @@ static inline pmd_t pmd_mkdevmap(pmd_t pmd)
 #define pud_pfn(pud)		((__pud_to_phys(pud) & PUD_MASK) >> PAGE_SHIFT)
 #define pfn_pud(pfn,prot)	__pud(__phys_to_pud_val((phys_addr_t)(pfn) << PAGE_SHIFT) | pgprot_val(prot))
 
-#define set_pmd_at(mm, addr, pmdp, pmd)	set_pte_at(mm, addr, (pte_t *)pmdp, pmd_pte(pmd))
-#define set_pud_at(mm, addr, pudp, pud)	set_pte_at(mm, addr, (pte_t *)pudp, pud_pte(pud))
+static inline void set_pmd_at(struct mm_struct *mm, unsigned long addr,
+			      pmd_t *pmdp, pmd_t pmd)
+{
+	page_table_check_pmd_set(mm, addr, pmdp, pmd);
+	return __set_pte_at(mm, addr, (pte_t *)pmdp, pmd_pte(pmd));
+}
+
+static inline void set_pud_at(struct mm_struct *mm, unsigned long addr,
+			      pud_t *pudp, pud_t pud)
+{
+	page_table_check_pud_set(mm, addr, pudp, pud);
+	return __set_pte_at(mm, addr, (pte_t *)pudp, pud_pte(pud));
+}
 
 #define __p4d_to_phys(p4d)	__pte_to_phys(p4d_pte(p4d))
 #define __phys_to_p4d_val(phys)	__phys_to_pte_val(phys)
@@ -535,7 +589,7 @@ extern pgprot_t phys_mem_access_prot(struct file *file, unsigned long pfn,
 				 PMD_TYPE_TABLE)
 #define pmd_sect(pmd)		((pmd_val(pmd) & PMD_TYPE_MASK) == \
 				 PMD_TYPE_SECT)
-#define pmd_leaf(pmd)		pmd_sect(pmd)
+#define pmd_leaf(pmd)		(pmd_present(pmd) && !pmd_table(pmd))
 #define pmd_bad(pmd)		(!pmd_table(pmd))
 
 #define pmd_leaf_size(pmd)	(pmd_cont(pmd) ? CONT_PMD_SIZE : PMD_SIZE)
@@ -625,8 +679,10 @@ static inline unsigned long pmd_page_vaddr(pmd_t pmd)
 #define pud_none(pud)		(!pud_val(pud))
 #define pud_bad(pud)		(!pud_table(pud))
 #define pud_present(pud)	pte_present(pud_pte(pud))
-#define pud_leaf(pud)		pud_sect(pud)
+#define pud_leaf(pud)		(pud_present(pud) && !pud_table(pud))
 #define pud_valid(pud)		pte_valid(pud_pte(pud))
+#define pud_user(pud)		pte_user(pud_pte(pud))
+
 
 static inline void set_pud(pud_t *pudp, pud_t pud)
 {
@@ -799,6 +855,23 @@ static inline int pgd_devmap(pgd_t pgd)
 }
 #endif
 
+#ifdef CONFIG_PAGE_TABLE_CHECK
+static inline bool pte_user_accessible_page(pte_t pte)
+{
+	return pte_present(pte) && (pte_user(pte) || pte_user_exec(pte));
+}
+
+static inline bool pmd_user_accessible_page(pmd_t pmd)
+{
+	return pmd_present(pmd) && (pmd_user(pmd) || pmd_user_exec(pmd));
+}
+
+static inline bool pud_user_accessible_page(pud_t pud)
+{
+	return pud_present(pud) && pud_user(pud);
+}
+#endif
+
 /*
  * Atomic pte/pmd modifications.
  */
@@ -860,7 +933,11 @@ static inline int pmdp_test_and_clear_young(struct vm_area_struct *vma,
 static inline pte_t ptep_get_and_clear(struct mm_struct *mm,
 				       unsigned long address, pte_t *ptep)
 {
-	return __pte(xchg_relaxed(&pte_val(*ptep), 0));
+	pte_t pte = __pte(xchg_relaxed(&pte_val(*ptep), 0));
+
+	page_table_check_pte_clear(mm, address, pte);
+
+	return pte;
 }
 
 #ifdef CONFIG_TRANSPARENT_HUGEPAGE
@@ -868,7 +945,11 @@ static inline pte_t ptep_get_and_clear(struct mm_struct *mm,
 static inline pmd_t pmdp_huge_get_and_clear(struct mm_struct *mm,
 					    unsigned long address, pmd_t *pmdp)
 {
-	return pte_pmd(ptep_get_and_clear(mm, address, (pte_t *)pmdp));
+	pmd_t pmd = __pmd(xchg_relaxed(&pmd_val(*pmdp), 0));
+
+	page_table_check_pmd_clear(mm, address, pmd);
+
+	return pmd;
 }
 #endif /* CONFIG_TRANSPARENT_HUGEPAGE */
 
@@ -902,6 +983,7 @@ static inline void pmdp_set_wrprotect(struct mm_struct *mm,
 static inline pmd_t pmdp_establish(struct vm_area_struct *vma,
 		unsigned long address, pmd_t *pmdp, pmd_t pmd)
 {
+	page_table_check_pmd_set(vma->vm_mm, address, pmdp, pmd);
 	return __pmd(xchg_relaxed(&pmd_val(*pmdp), pmd_val(pmd)));
 }
 #endif
@@ -909,12 +991,13 @@ static inline pmd_t pmdp_establish(struct vm_area_struct *vma,
 /*
  * Encode and decode a swap entry:
  *	bits 0-1:	present (must be zero)
- *	bits 2-7:	swap type
+ *	bits 2:		remember PG_anon_exclusive
+ *	bits 3-7:	swap type
  *	bits 8-57:	swap offset
  *	bit  58:	PTE_PROT_NONE (must be zero)
  */
-#define __SWP_TYPE_SHIFT	2
-#define __SWP_TYPE_BITS		6
+#define __SWP_TYPE_SHIFT	3
+#define __SWP_TYPE_BITS		5
 #define __SWP_OFFSET_BITS	50
 #define __SWP_TYPE_MASK		((1 << __SWP_TYPE_BITS) - 1)
 #define __SWP_OFFSET_SHIFT	(__SWP_TYPE_BITS + __SWP_TYPE_SHIFT)
@@ -964,10 +1047,10 @@ static inline void arch_swap_invalidate_area(int type)
 }
 
 #define __HAVE_ARCH_SWAP_RESTORE
-static inline void arch_swap_restore(swp_entry_t entry, struct page *page)
+static inline void arch_swap_restore(swp_entry_t entry, struct folio *folio)
 {
-	if (system_supports_mte() && mte_restore_tags(entry, page))
-		set_bit(PG_mte_tagged, &page->flags);
+	if (system_supports_mte() && mte_restore_tags(entry, &folio->page))
+		set_bit(PG_mte_tagged, &folio->flags);
 }
 
 #endif /* CONFIG_ARM64_MTE */
@@ -999,34 +1082,13 @@ static inline void update_mmu_cache(struct vm_area_struct *vma,
  * page after fork() + CoW for pfn mappings. We don't always have a
  * hardware-managed access flag on arm64.
  */
-static inline bool arch_faults_on_old_pte(void)
-{
-	WARN_ON(preemptible());
-
-	return !cpu_has_hw_af();
-}
-#define arch_faults_on_old_pte		arch_faults_on_old_pte
+#define arch_has_hw_pte_young		cpu_has_hw_af
 
 /*
  * Experimentally, it's cheap to set the access flag in hardware and we
  * benefit from prefaulting mappings as 'old' to start with.
  */
-static inline bool arch_wants_old_prefaulted_pte(void)
-{
-	return !arch_faults_on_old_pte();
-}
-#define arch_wants_old_prefaulted_pte	arch_wants_old_prefaulted_pte
-
-static inline pgprot_t arch_filter_pgprot(pgprot_t prot)
-{
-	if (cpus_have_const_cap(ARM64_HAS_EPAN))
-		return prot;
-
-	if (pgprot_val(prot) != pgprot_val(PAGE_EXECONLY))
-		return prot;
-
-	return PAGE_READONLY_EXEC;
-}
+#define arch_wants_old_prefaulted_pte	cpu_has_hw_af
 
 static inline bool pud_sect_supported(void)
 {
diff --git a/arch/arm64/include/asm/preempt.h b/arch/arm64/include/asm/preempt.h
index e83f0982b99c..0159b625cc7f 100644
--- a/arch/arm64/include/asm/preempt.h
+++ b/arch/arm64/include/asm/preempt.h
@@ -2,6 +2,7 @@
 #ifndef __ASM_PREEMPT_H
 #define __ASM_PREEMPT_H
 
+#include <linux/jump_label.h>
 #include <linux/thread_info.h>
 
 #define PREEMPT_NEED_RESCHED	BIT(32)
@@ -80,10 +81,24 @@ static inline bool should_resched(int preempt_offset)
 }
 
 #ifdef CONFIG_PREEMPTION
+
 void preempt_schedule(void);
-#define __preempt_schedule() preempt_schedule()
 void preempt_schedule_notrace(void);
-#define __preempt_schedule_notrace() preempt_schedule_notrace()
+
+#ifdef CONFIG_PREEMPT_DYNAMIC
+
+DECLARE_STATIC_KEY_TRUE(sk_dynamic_irqentry_exit_cond_resched);
+void dynamic_preempt_schedule(void);
+#define __preempt_schedule()		dynamic_preempt_schedule()
+void dynamic_preempt_schedule_notrace(void);
+#define __preempt_schedule_notrace()	dynamic_preempt_schedule_notrace()
+
+#else /* CONFIG_PREEMPT_DYNAMIC */
+
+#define __preempt_schedule()		preempt_schedule()
+#define __preempt_schedule_notrace()	preempt_schedule_notrace()
+
+#endif /* CONFIG_PREEMPT_DYNAMIC */
 #endif /* CONFIG_PREEMPTION */
 
 #endif /* __ASM_PREEMPT_H */
diff --git a/arch/arm64/include/asm/processor.h b/arch/arm64/include/asm/processor.h
index 6f41b65f9962..445aa3af3b76 100644
--- a/arch/arm64/include/asm/processor.h
+++ b/arch/arm64/include/asm/processor.h
@@ -21,6 +21,7 @@
 
 #define MTE_CTRL_TCF_SYNC		(1UL << 16)
 #define MTE_CTRL_TCF_ASYNC		(1UL << 17)
+#define MTE_CTRL_TCF_ASYMM		(1UL << 18)
 
 #ifndef __ASSEMBLY__
 
@@ -91,8 +92,8 @@
 #endif /* CONFIG_COMPAT */
 
 #ifndef CONFIG_ARM64_FORCE_52BIT
-#define arch_get_mmap_end(addr) ((addr > DEFAULT_MAP_WINDOW) ? TASK_SIZE :\
-				DEFAULT_MAP_WINDOW)
+#define arch_get_mmap_end(addr, len, flags) \
+		(((addr) > DEFAULT_MAP_WINDOW) ? TASK_SIZE : DEFAULT_MAP_WINDOW)
 
 #define arch_get_mmap_base(addr, base) ((addr > DEFAULT_MAP_WINDOW) ? \
 					base + TASK_SIZE - DEFAULT_MAP_WINDOW :\
@@ -117,6 +118,7 @@ struct debug_info {
 
 enum vec_type {
 	ARM64_VEC_SVE = 0,
+	ARM64_VEC_SME,
 	ARM64_VEC_MAX,
 };
 
@@ -152,6 +154,7 @@ struct thread_struct {
 
 	unsigned int		fpsimd_cpu;
 	void			*sve_state;	/* SVE registers, if any */
+	void			*za_state;	/* ZA register, if any */
 	unsigned int		vl[ARM64_VEC_MAX];	/* vector length */
 	unsigned int		vl_onexec[ARM64_VEC_MAX]; /* vl after next exec */
 	unsigned long		fault_address;	/* fault info */
@@ -167,6 +170,8 @@ struct thread_struct {
 	u64			mte_ctrl;
 #endif
 	u64			sctlr_user;
+	u64			svcr;
+	u64			tpidr2_el0;
 };
 
 static inline unsigned int thread_get_vl(struct thread_struct *thread,
@@ -180,6 +185,19 @@ static inline unsigned int thread_get_sve_vl(struct thread_struct *thread)
 	return thread_get_vl(thread, ARM64_VEC_SVE);
 }
 
+static inline unsigned int thread_get_sme_vl(struct thread_struct *thread)
+{
+	return thread_get_vl(thread, ARM64_VEC_SME);
+}
+
+static inline unsigned int thread_get_cur_vl(struct thread_struct *thread)
+{
+	if (system_supports_sme() && (thread->svcr & SVCR_SM_MASK))
+		return thread_get_sme_vl(thread);
+	else
+		return thread_get_sve_vl(thread);
+}
+
 unsigned int task_get_vl(const struct task_struct *task, enum vec_type type);
 void task_set_vl(struct task_struct *task, enum vec_type type,
 		 unsigned long vl);
@@ -193,6 +211,11 @@ static inline unsigned int task_get_sve_vl(const struct task_struct *task)
 	return task_get_vl(task, ARM64_VEC_SVE);
 }
 
+static inline unsigned int task_get_sme_vl(const struct task_struct *task)
+{
+	return task_get_vl(task, ARM64_VEC_SME);
+}
+
 static inline void task_set_sve_vl(struct task_struct *task, unsigned long vl)
 {
 	task_set_vl(task, ARM64_VEC_SVE, vl);
@@ -249,8 +272,9 @@ void tls_preserve_current_state(void);
 
 static inline void start_thread_common(struct pt_regs *regs, unsigned long pc)
 {
+	s32 previous_syscall = regs->syscallno;
 	memset(regs, 0, sizeof(*regs));
-	forget_syscall(regs);
+	regs->syscallno = previous_syscall;
 	regs->pc = pc;
 
 	if (system_uses_irq_prio_masking())
@@ -299,9 +323,6 @@ static inline bool is_ttbr1_addr(unsigned long addr)
 /* Forward declaration, a strange C thing */
 struct task_struct;
 
-/* Free all resources held by a thread. */
-extern void release_thread(struct task_struct *);
-
 unsigned long __get_wchan(struct task_struct *p);
 
 void update_sctlr_el1(u64 sctlr);
@@ -353,9 +374,11 @@ extern void __init minsigstksz_setup(void);
  */
 #include <asm/fpsimd.h>
 
-/* Userspace interface for PR_SVE_{SET,GET}_VL prctl()s: */
+/* Userspace interface for PR_S[MV]E_{SET,GET}_VL prctl()s: */
 #define SVE_SET_VL(arg)	sve_set_current_vl(arg)
 #define SVE_GET_VL()	sve_get_current_vl()
+#define SME_SET_VL(arg)	sme_set_current_vl(arg)
+#define SME_GET_VL()	sme_get_current_vl()
 
 /* PR_PAC_RESET_KEYS prctl */
 #define PAC_RESET_KEYS(tsk, arg)	ptrauth_prctl_reset_keys(tsk, arg)
@@ -380,13 +403,11 @@ long get_tagged_addr_ctrl(struct task_struct *task);
  * of header definitions for the use of task_stack_page.
  */
 
-#define current_top_of_stack()								\
-({											\
-	struct stack_info _info;							\
-	BUG_ON(!on_accessible_stack(current, current_stack_pointer, 1, &_info));	\
-	_info.high;									\
-})
-#define on_thread_stack()	(on_task_stack(current, current_stack_pointer, 1, NULL))
+/*
+ * The top of the current task's task stack
+ */
+#define current_top_of_stack()	((unsigned long)current->stack + THREAD_SIZE)
+#define on_thread_stack()	(on_task_stack(current, current_stack_pointer, 1))
 
 #endif /* __ASSEMBLY__ */
 #endif /* __ASM_PROCESSOR_H */
diff --git a/arch/arm64/include/asm/rwonce.h b/arch/arm64/include/asm/rwonce.h
index 1bce62fa908a..56f7b1d4d54b 100644
--- a/arch/arm64/include/asm/rwonce.h
+++ b/arch/arm64/include/asm/rwonce.h
@@ -5,7 +5,7 @@
 #ifndef __ASM_RWONCE_H
 #define __ASM_RWONCE_H
 
-#ifdef CONFIG_LTO
+#if defined(CONFIG_LTO) && !defined(__ASSEMBLY__)
 
 #include <linux/compiler_types.h>
 #include <asm/alternative-macros.h>
@@ -66,7 +66,7 @@
 })
 
 #endif	/* !BUILD_VDSO */
-#endif	/* CONFIG_LTO */
+#endif	/* CONFIG_LTO && !__ASSEMBLY__ */
 
 #include <asm-generic/rwonce.h>
 
diff --git a/arch/arm64/include/asm/sdei.h b/arch/arm64/include/asm/sdei.h
index 7bea1d705dd6..4292d9bafb9d 100644
--- a/arch/arm64/include/asm/sdei.h
+++ b/arch/arm64/include/asm/sdei.h
@@ -43,22 +43,5 @@ unsigned long do_sdei_event(struct pt_regs *regs,
 unsigned long sdei_arch_get_entry_point(int conduit);
 #define sdei_arch_get_entry_point(x)	sdei_arch_get_entry_point(x)
 
-struct stack_info;
-
-bool _on_sdei_stack(unsigned long sp, unsigned long size,
-		    struct stack_info *info);
-static inline bool on_sdei_stack(unsigned long sp, unsigned long size,
-				struct stack_info *info)
-{
-	if (!IS_ENABLED(CONFIG_VMAP_STACK))
-		return false;
-	if (!IS_ENABLED(CONFIG_ARM_SDE_INTERFACE))
-		return false;
-	if (in_nmi())
-		return _on_sdei_stack(sp, size, info);
-
-	return false;
-}
-
 #endif /* __ASSEMBLY__ */
 #endif	/* __ASM_SDEI_H */
diff --git a/arch/arm64/include/asm/sections.h b/arch/arm64/include/asm/sections.h
index 152cb35bf9df..40971ac1303f 100644
--- a/arch/arm64/include/asm/sections.h
+++ b/arch/arm64/include/asm/sections.h
@@ -23,4 +23,9 @@ extern char __mmuoff_data_start[], __mmuoff_data_end[];
 extern char __entry_tramp_text_start[], __entry_tramp_text_end[];
 extern char __relocate_new_kernel_start[], __relocate_new_kernel_end[];
 
+static inline size_t entry_tramp_text_size(void)
+{
+	return __entry_tramp_text_end - __entry_tramp_text_start;
+}
+
 #endif /* __ASM_SECTIONS_H */
diff --git a/arch/arm64/include/asm/setup.h b/arch/arm64/include/asm/setup.h
index 6437df661700..f4af547ef54c 100644
--- a/arch/arm64/include/asm/setup.h
+++ b/arch/arm64/include/asm/setup.h
@@ -3,6 +3,8 @@
 #ifndef __ARM64_ASM_SETUP_H
 #define __ARM64_ASM_SETUP_H
 
+#include <linux/string.h>
+
 #include <uapi/asm/setup.h>
 
 void *get_early_fdt_ptr(void);
@@ -14,4 +16,19 @@ void early_fdt_map(u64 dt_phys);
 extern phys_addr_t __fdt_pointer __initdata;
 extern u64 __cacheline_aligned boot_args[4];
 
+static inline bool arch_parse_debug_rodata(char *arg)
+{
+	extern bool rodata_enabled;
+	extern bool rodata_full;
+
+	if (arg && !strcmp(arg, "full")) {
+		rodata_enabled = true;
+		rodata_full = true;
+		return true;
+	}
+
+	return false;
+}
+#define arch_parse_debug_rodata arch_parse_debug_rodata
+
 #endif
diff --git a/arch/arm64/include/asm/spectre.h b/arch/arm64/include/asm/spectre.h
index f62ca39da6c5..aa3d3607d5c8 100644
--- a/arch/arm64/include/asm/spectre.h
+++ b/arch/arm64/include/asm/spectre.h
@@ -67,7 +67,8 @@ struct bp_hardening_data {
 
 DECLARE_PER_CPU_READ_MOSTLY(struct bp_hardening_data, bp_hardening_data);
 
-static inline void arm64_apply_bp_hardening(void)
+/* Called during entry so must be __always_inline */
+static __always_inline void arm64_apply_bp_hardening(void)
 {
 	struct bp_hardening_data *d;
 
@@ -93,5 +94,9 @@ void spectre_v4_enable_task_mitigation(struct task_struct *tsk);
 
 enum mitigation_state arm64_get_meltdown_state(void);
 
+enum mitigation_state arm64_get_spectre_bhb_state(void);
+bool is_spectre_bhb_affected(const struct arm64_cpu_capabilities *entry, int scope);
+u8 spectre_bhb_loop_affected(int scope);
+void spectre_bhb_enable_mitigation(const struct arm64_cpu_capabilities *__unused);
 #endif	/* __ASSEMBLY__ */
 #endif	/* __ASM_SPECTRE_H */
diff --git a/arch/arm64/include/asm/stacktrace.h b/arch/arm64/include/asm/stacktrace.h
index 6564a01cc085..5a0edb064ea4 100644
--- a/arch/arm64/include/asm/stacktrace.h
+++ b/arch/arm64/include/asm/stacktrace.h
@@ -8,145 +8,100 @@
 #include <linux/percpu.h>
 #include <linux/sched.h>
 #include <linux/sched/task_stack.h>
-#include <linux/types.h>
 #include <linux/llist.h>
 
 #include <asm/memory.h>
+#include <asm/pointer_auth.h>
 #include <asm/ptrace.h>
 #include <asm/sdei.h>
 
-enum stack_type {
-	STACK_TYPE_UNKNOWN,
-	STACK_TYPE_TASK,
-	STACK_TYPE_IRQ,
-	STACK_TYPE_OVERFLOW,
-	STACK_TYPE_SDEI_NORMAL,
-	STACK_TYPE_SDEI_CRITICAL,
-	__NR_STACK_TYPES
-};
-
-struct stack_info {
-	unsigned long low;
-	unsigned long high;
-	enum stack_type type;
-};
+#include <asm/stacktrace/common.h>
 
-/*
- * A snapshot of a frame record or fp/lr register values, along with some
- * accounting information necessary for robust unwinding.
- *
- * @fp:          The fp value in the frame record (or the real fp)
- * @pc:          The lr value in the frame record (or the real lr)
- *
- * @stacks_done: Stacks which have been entirely unwound, for which it is no
- *               longer valid to unwind to.
- *
- * @prev_fp:     The fp that pointed to this frame record, or a synthetic value
- *               of 0. This is used to ensure that within a stack, each
- *               subsequent frame record is at an increasing address.
- * @prev_type:   The type of stack this frame record was on, or a synthetic
- *               value of STACK_TYPE_UNKNOWN. This is used to detect a
- *               transition from one stack to another.
- */
-struct stackframe {
-	unsigned long fp;
-	unsigned long pc;
-	DECLARE_BITMAP(stacks_done, __NR_STACK_TYPES);
-	unsigned long prev_fp;
-	enum stack_type prev_type;
-#ifdef CONFIG_KRETPROBES
-	struct llist_node *kr_cur;
-#endif
-};
-
-extern int unwind_frame(struct task_struct *tsk, struct stackframe *frame);
-extern void walk_stackframe(struct task_struct *tsk, struct stackframe *frame,
-			    bool (*fn)(void *, unsigned long), void *data);
 extern void dump_backtrace(struct pt_regs *regs, struct task_struct *tsk,
 			   const char *loglvl);
 
 DECLARE_PER_CPU(unsigned long *, irq_stack_ptr);
 
-static inline bool on_stack(unsigned long sp, unsigned long size,
-			    unsigned long low, unsigned long high,
-			    enum stack_type type, struct stack_info *info)
-{
-	if (!low)
-		return false;
-
-	if (sp < low || sp + size < sp || sp + size > high)
-		return false;
-
-	if (info) {
-		info->low = low;
-		info->high = high;
-		info->type = type;
-	}
-	return true;
-}
-
-static inline bool on_irq_stack(unsigned long sp, unsigned long size,
-				struct stack_info *info)
+static inline struct stack_info stackinfo_get_irq(void)
 {
 	unsigned long low = (unsigned long)raw_cpu_read(irq_stack_ptr);
 	unsigned long high = low + IRQ_STACK_SIZE;
 
-	return on_stack(sp, size, low, high, STACK_TYPE_IRQ, info);
+	return (struct stack_info) {
+		.low = low,
+		.high = high,
+	};
 }
 
-static inline bool on_task_stack(const struct task_struct *tsk,
-				 unsigned long sp, unsigned long size,
-				 struct stack_info *info)
+static inline bool on_irq_stack(unsigned long sp, unsigned long size)
+{
+	struct stack_info info = stackinfo_get_irq();
+	return stackinfo_on_stack(&info, sp, size);
+}
+
+static inline struct stack_info stackinfo_get_task(const struct task_struct *tsk)
 {
 	unsigned long low = (unsigned long)task_stack_page(tsk);
 	unsigned long high = low + THREAD_SIZE;
 
-	return on_stack(sp, size, low, high, STACK_TYPE_TASK, info);
+	return (struct stack_info) {
+		.low = low,
+		.high = high,
+	};
+}
+
+static inline bool on_task_stack(const struct task_struct *tsk,
+				 unsigned long sp, unsigned long size)
+{
+	struct stack_info info = stackinfo_get_task(tsk);
+	return stackinfo_on_stack(&info, sp, size);
 }
 
 #ifdef CONFIG_VMAP_STACK
 DECLARE_PER_CPU(unsigned long [OVERFLOW_STACK_SIZE/sizeof(long)], overflow_stack);
 
-static inline bool on_overflow_stack(unsigned long sp, unsigned long size,
-				struct stack_info *info)
+static inline struct stack_info stackinfo_get_overflow(void)
 {
 	unsigned long low = (unsigned long)raw_cpu_ptr(overflow_stack);
 	unsigned long high = low + OVERFLOW_STACK_SIZE;
 
-	return on_stack(sp, size, low, high, STACK_TYPE_OVERFLOW, info);
+	return (struct stack_info) {
+		.low = low,
+		.high = high,
+	};
 }
 #else
-static inline bool on_overflow_stack(unsigned long sp, unsigned long size,
-			struct stack_info *info) { return false; }
+#define stackinfo_get_overflow()	stackinfo_get_unknown()
 #endif
 
+#if defined(CONFIG_ARM_SDE_INTERFACE) && defined(CONFIG_VMAP_STACK)
+DECLARE_PER_CPU(unsigned long *, sdei_stack_normal_ptr);
+DECLARE_PER_CPU(unsigned long *, sdei_stack_critical_ptr);
 
-/*
- * We can only safely access per-cpu stacks from current in a non-preemptible
- * context.
- */
-static inline bool on_accessible_stack(const struct task_struct *tsk,
-				       unsigned long sp, unsigned long size,
-				       struct stack_info *info)
+static inline struct stack_info stackinfo_get_sdei_normal(void)
 {
-	if (info)
-		info->type = STACK_TYPE_UNKNOWN;
-
-	if (on_task_stack(tsk, sp, size, info))
-		return true;
-	if (tsk != current || preemptible())
-		return false;
-	if (on_irq_stack(sp, size, info))
-		return true;
-	if (on_overflow_stack(sp, size, info))
-		return true;
-	if (on_sdei_stack(sp, size, info))
-		return true;
-
-	return false;
+	unsigned long low = (unsigned long)raw_cpu_read(sdei_stack_normal_ptr);
+	unsigned long high = low + SDEI_STACK_SIZE;
+
+	return (struct stack_info) {
+		.low = low,
+		.high = high,
+	};
 }
 
-void start_backtrace(struct stackframe *frame, unsigned long fp,
-		     unsigned long pc);
+static inline struct stack_info stackinfo_get_sdei_critical(void)
+{
+	unsigned long low = (unsigned long)raw_cpu_read(sdei_stack_critical_ptr);
+	unsigned long high = low + SDEI_STACK_SIZE;
+
+	return (struct stack_info) {
+		.low = low,
+		.high = high,
+	};
+}
+#else
+#define stackinfo_get_sdei_normal()	stackinfo_get_unknown()
+#define stackinfo_get_sdei_critical()	stackinfo_get_unknown()
+#endif
 
 #endif	/* __ASM_STACKTRACE_H */
diff --git a/arch/arm64/include/asm/stacktrace/common.h b/arch/arm64/include/asm/stacktrace/common.h
new file mode 100644
index 000000000000..508f734de46e
--- /dev/null
+++ b/arch/arm64/include/asm/stacktrace/common.h
@@ -0,0 +1,176 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Common arm64 stack unwinder code.
+ *
+ * See: arch/arm64/kernel/stacktrace.c for the reference implementation.
+ *
+ * Copyright (C) 2012 ARM Ltd.
+ */
+#ifndef __ASM_STACKTRACE_COMMON_H
+#define __ASM_STACKTRACE_COMMON_H
+
+#include <linux/kprobes.h>
+#include <linux/types.h>
+
+struct stack_info {
+	unsigned long low;
+	unsigned long high;
+};
+
+/**
+ * struct unwind_state - state used for robust unwinding.
+ *
+ * @fp:          The fp value in the frame record (or the real fp)
+ * @pc:          The lr value in the frame record (or the real lr)
+ *
+ * @kr_cur:      When KRETPROBES is selected, holds the kretprobe instance
+ *               associated with the most recently encountered replacement lr
+ *               value.
+ *
+ * @task:        The task being unwound.
+ *
+ * @stack:       The stack currently being unwound.
+ * @stacks:      An array of stacks which can be unwound.
+ * @nr_stacks:   The number of stacks in @stacks.
+ */
+struct unwind_state {
+	unsigned long fp;
+	unsigned long pc;
+#ifdef CONFIG_KRETPROBES
+	struct llist_node *kr_cur;
+#endif
+	struct task_struct *task;
+
+	struct stack_info stack;
+	struct stack_info *stacks;
+	int nr_stacks;
+};
+
+static inline struct stack_info stackinfo_get_unknown(void)
+{
+	return (struct stack_info) {
+		.low = 0,
+		.high = 0,
+	};
+}
+
+static inline bool stackinfo_on_stack(const struct stack_info *info,
+				      unsigned long sp, unsigned long size)
+{
+	if (!info->low)
+		return false;
+
+	if (sp < info->low || sp + size < sp || sp + size > info->high)
+		return false;
+
+	return true;
+}
+
+static inline void unwind_init_common(struct unwind_state *state,
+				      struct task_struct *task)
+{
+	state->task = task;
+#ifdef CONFIG_KRETPROBES
+	state->kr_cur = NULL;
+#endif
+
+	state->stack = stackinfo_get_unknown();
+}
+
+static struct stack_info *unwind_find_next_stack(const struct unwind_state *state,
+						 unsigned long sp,
+						 unsigned long size)
+{
+	for (int i = 0; i < state->nr_stacks; i++) {
+		struct stack_info *info = &state->stacks[i];
+
+		if (stackinfo_on_stack(info, sp, size))
+			return info;
+	}
+
+	return NULL;
+}
+
+/**
+ * unwind_consume_stack() - Check if an object is on an accessible stack,
+ * updating stack boundaries so that future unwind steps cannot consume this
+ * object again.
+ *
+ * @state: the current unwind state.
+ * @sp:    the base address of the object.
+ * @size:  the size of the object.
+ *
+ * Return: 0 upon success, an error code otherwise.
+ */
+static inline int unwind_consume_stack(struct unwind_state *state,
+				       unsigned long sp,
+				       unsigned long size)
+{
+	struct stack_info *next;
+
+	if (stackinfo_on_stack(&state->stack, sp, size))
+		goto found;
+
+	next = unwind_find_next_stack(state, sp, size);
+	if (!next)
+		return -EINVAL;
+
+	/*
+	 * Stack transitions are strictly one-way, and once we've
+	 * transitioned from one stack to another, it's never valid to
+	 * unwind back to the old stack.
+	 *
+	 * Remove the current stack from the list of stacks so that it cannot
+	 * be found on a subsequent transition.
+	 *
+	 * Note that stacks can nest in several valid orders, e.g.
+	 *
+	 *   TASK -> IRQ -> OVERFLOW -> SDEI_NORMAL
+	 *   TASK -> SDEI_NORMAL -> SDEI_CRITICAL -> OVERFLOW
+	 *   HYP -> OVERFLOW
+	 *
+	 * ... so we do not check the specific order of stack
+	 * transitions.
+	 */
+	state->stack = *next;
+	*next = stackinfo_get_unknown();
+
+found:
+	/*
+	 * Future unwind steps can only consume stack above this frame record.
+	 * Update the current stack to start immediately above it.
+	 */
+	state->stack.low = sp + size;
+	return 0;
+}
+
+/**
+ * unwind_next_frame_record() - Unwind to the next frame record.
+ *
+ * @state:        the current unwind state.
+ *
+ * Return: 0 upon success, an error code otherwise.
+ */
+static inline int
+unwind_next_frame_record(struct unwind_state *state)
+{
+	unsigned long fp = state->fp;
+	int err;
+
+	if (fp & 0x7)
+		return -EINVAL;
+
+	err = unwind_consume_stack(state, fp, 16);
+	if (err)
+		return err;
+
+	/*
+	 * Record this frame record's values.
+	 */
+	state->fp = READ_ONCE(*(unsigned long *)(fp));
+	state->pc = READ_ONCE(*(unsigned long *)(fp + 8));
+
+	return 0;
+}
+
+#endif	/* __ASM_STACKTRACE_COMMON_H */
diff --git a/arch/arm64/include/asm/stacktrace/nvhe.h b/arch/arm64/include/asm/stacktrace/nvhe.h
new file mode 100644
index 000000000000..25ab83a315a7
--- /dev/null
+++ b/arch/arm64/include/asm/stacktrace/nvhe.h
@@ -0,0 +1,55 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * KVM nVHE hypervisor stack tracing support.
+ *
+ * The unwinder implementation depends on the nVHE mode:
+ *
+ *   1) Non-protected nVHE mode - the host can directly access the
+ *      HYP stack pages and unwind the HYP stack in EL1. This saves having
+ *      to allocate shared buffers for the host to read the unwinded
+ *      stacktrace.
+ *
+ *   2) pKVM (protected nVHE) mode - the host cannot directly access
+ *      the HYP memory. The stack is unwinded in EL2 and dumped to a shared
+ *      buffer where the host can read and print the stacktrace.
+ *
+ * Copyright (C) 2022 Google LLC
+ */
+#ifndef __ASM_STACKTRACE_NVHE_H
+#define __ASM_STACKTRACE_NVHE_H
+
+#include <asm/stacktrace/common.h>
+
+/**
+ * kvm_nvhe_unwind_init() - Start an unwind from the given nVHE HYP fp and pc
+ *
+ * @state : unwind_state to initialize
+ * @fp    : frame pointer at which to start the unwinding.
+ * @pc    : program counter at which to start the unwinding.
+ */
+static inline void kvm_nvhe_unwind_init(struct unwind_state *state,
+					unsigned long fp,
+					unsigned long pc)
+{
+	unwind_init_common(state, NULL);
+
+	state->fp = fp;
+	state->pc = pc;
+}
+
+#ifndef __KVM_NVHE_HYPERVISOR__
+/*
+ * Conventional (non-protected) nVHE HYP stack unwinder
+ *
+ * In non-protected mode, the unwinding is done from kernel proper context
+ * (by the host in EL1).
+ */
+
+DECLARE_KVM_NVHE_PER_CPU(unsigned long [OVERFLOW_STACK_SIZE/sizeof(long)], overflow_stack);
+DECLARE_KVM_NVHE_PER_CPU(struct kvm_nvhe_stacktrace_info, kvm_stacktrace_info);
+DECLARE_PER_CPU(unsigned long, kvm_arm_hyp_stack_page);
+
+void kvm_nvhe_dump_backtrace(unsigned long hyp_offset);
+
+#endif	/* __KVM_NVHE_HYPERVISOR__ */
+#endif	/* __ASM_STACKTRACE_NVHE_H */
diff --git a/arch/arm64/include/asm/stage2_pgtable.h b/arch/arm64/include/asm/stage2_pgtable.h
index fe341a6578c3..c8dca8ae359c 100644
--- a/arch/arm64/include/asm/stage2_pgtable.h
+++ b/arch/arm64/include/asm/stage2_pgtable.h
@@ -11,13 +11,6 @@
 #include <linux/pgtable.h>
 
 /*
- * PGDIR_SHIFT determines the size a top-level page table entry can map
- * and depends on the number of levels in the page table. Compute the
- * PGDIR_SHIFT for a given number of levels.
- */
-#define pt_levels_pgdir_shift(lvls)	ARM64_HW_PGTABLE_LEVEL_SHIFT(4 - (lvls))
-
-/*
  * The hardware supports concatenation of up to 16 tables at stage2 entry
  * level and we use the feature whenever possible, which means we resolve 4
  * additional bits of address at the entry level.
@@ -30,11 +23,6 @@
 #define stage2_pgtable_levels(ipa)	ARM64_HW_PGTABLE_LEVELS((ipa) - 4)
 #define kvm_stage2_levels(kvm)		VTCR_EL2_LVLS(kvm->arch.vtcr)
 
-/* stage2_pgdir_shift() is the size mapped by top-level stage2 entry for the VM */
-#define stage2_pgdir_shift(kvm)		pt_levels_pgdir_shift(kvm_stage2_levels(kvm))
-#define stage2_pgdir_size(kvm)		(1ULL << stage2_pgdir_shift(kvm))
-#define stage2_pgdir_mask(kvm)		~(stage2_pgdir_size(kvm) - 1)
-
 /*
  * kvm_mmmu_cache_min_pages() is the number of pages required to install
  * a stage-2 translation. We pre-allocate the entry level page table at
@@ -42,12 +30,4 @@
  */
 #define kvm_mmu_cache_min_pages(kvm)	(kvm_stage2_levels(kvm) - 1)
 
-static inline phys_addr_t
-stage2_pgd_addr_end(struct kvm *kvm, phys_addr_t addr, phys_addr_t end)
-{
-	phys_addr_t boundary = (addr + stage2_pgdir_size(kvm)) & stage2_pgdir_mask(kvm);
-
-	return (boundary - 1 < end - 1) ? boundary : end;
-}
-
 #endif	/* __ARM64_S2_PGTABLE_H_ */
diff --git a/arch/arm64/include/asm/string.h b/arch/arm64/include/asm/string.h
index 95f7686b728d..3a3264ff47b9 100644
--- a/arch/arm64/include/asm/string.h
+++ b/arch/arm64/include/asm/string.h
@@ -12,13 +12,11 @@ extern char *strrchr(const char *, int c);
 #define __HAVE_ARCH_STRCHR
 extern char *strchr(const char *, int c);
 
-#ifndef CONFIG_KASAN_HW_TAGS
 #define __HAVE_ARCH_STRCMP
 extern int strcmp(const char *, const char *);
 
 #define __HAVE_ARCH_STRNCMP
 extern int strncmp(const char *, const char *, __kernel_size_t);
-#endif
 
 #define __HAVE_ARCH_STRLEN
 extern __kernel_size_t strlen(const char *);
diff --git a/arch/arm64/include/asm/syscall_wrapper.h b/arch/arm64/include/asm/syscall_wrapper.h
index b383b4802a7b..d30217c21eff 100644
--- a/arch/arm64/include/asm/syscall_wrapper.h
+++ b/arch/arm64/include/asm/syscall_wrapper.h
@@ -8,7 +8,7 @@
 #ifndef __ASM_SYSCALL_WRAPPER_H
 #define __ASM_SYSCALL_WRAPPER_H
 
-struct pt_regs;
+#include <asm/ptrace.h>
 
 #define SC_ARM64_REGS_TO_ARGS(x, ...)				\
 	__MAP(x,__SC_ARGS					\
diff --git a/arch/arm64/include/asm/sysreg.h b/arch/arm64/include/asm/sysreg.h
index 16b3f1a1d468..7d301700d1a9 100644
--- a/arch/arm64/include/asm/sysreg.h
+++ b/arch/arm64/include/asm/sysreg.h
@@ -115,9 +115,21 @@
 #define SYS_DC_CISW			sys_insn(1, 0, 7, 14, 2)
 
 /*
+ * Automatically generated definitions for system registers, the
+ * manual encodings below are in the process of being converted to
+ * come from here. The header relies on the definition of sys_reg()
+ * earlier in this file.
+ */
+#include "asm/sysreg-defs.h"
+
+/*
  * System registers, organised loosely by encoding but grouped together
  * where the architected name contains an index. e.g. ID_MMFR<n>_EL1.
  */
+#define SYS_SVCR_SMSTOP_SM_EL0		sys_reg(0, 3, 4, 2, 3)
+#define SYS_SVCR_SMSTART_SM_EL0		sys_reg(0, 3, 4, 3, 3)
+#define SYS_SVCR_SMSTOP_SMZA_EL0	sys_reg(0, 3, 4, 6, 3)
+
 #define SYS_OSDTRRX_EL1			sys_reg(2, 0, 0, 0, 2)
 #define SYS_MDCCINT_EL1			sys_reg(2, 0, 0, 2, 0)
 #define SYS_MDSCR_EL1			sys_reg(2, 0, 0, 2, 2)
@@ -128,8 +140,16 @@
 #define SYS_DBGWVRn_EL1(n)		sys_reg(2, 0, 0, n, 6)
 #define SYS_DBGWCRn_EL1(n)		sys_reg(2, 0, 0, n, 7)
 #define SYS_MDRAR_EL1			sys_reg(2, 0, 1, 0, 0)
+
 #define SYS_OSLAR_EL1			sys_reg(2, 0, 1, 0, 4)
+#define SYS_OSLAR_OSLK			BIT(0)
+
 #define SYS_OSLSR_EL1			sys_reg(2, 0, 1, 1, 4)
+#define SYS_OSLSR_OSLM_MASK		(BIT(3) | BIT(0))
+#define SYS_OSLSR_OSLM_NI		0
+#define SYS_OSLSR_OSLM_IMPLEMENTED	BIT(3)
+#define SYS_OSLSR_OSLK			BIT(1)
+
 #define SYS_OSDLR_EL1			sys_reg(2, 0, 1, 3, 4)
 #define SYS_DBGPRCR_EL1			sys_reg(2, 0, 1, 4, 4)
 #define SYS_DBGCLAIMSET_EL1		sys_reg(2, 0, 7, 8, 6)
@@ -170,34 +190,12 @@
 #define SYS_MVFR1_EL1			sys_reg(3, 0, 0, 3, 1)
 #define SYS_MVFR2_EL1			sys_reg(3, 0, 0, 3, 2)
 
-#define SYS_ID_AA64PFR0_EL1		sys_reg(3, 0, 0, 4, 0)
-#define SYS_ID_AA64PFR1_EL1		sys_reg(3, 0, 0, 4, 1)
-#define SYS_ID_AA64ZFR0_EL1		sys_reg(3, 0, 0, 4, 4)
-
-#define SYS_ID_AA64DFR0_EL1		sys_reg(3, 0, 0, 5, 0)
-#define SYS_ID_AA64DFR1_EL1		sys_reg(3, 0, 0, 5, 1)
-
-#define SYS_ID_AA64AFR0_EL1		sys_reg(3, 0, 0, 5, 4)
-#define SYS_ID_AA64AFR1_EL1		sys_reg(3, 0, 0, 5, 5)
-
-#define SYS_ID_AA64ISAR0_EL1		sys_reg(3, 0, 0, 6, 0)
-#define SYS_ID_AA64ISAR1_EL1		sys_reg(3, 0, 0, 6, 1)
-
-#define SYS_ID_AA64MMFR0_EL1		sys_reg(3, 0, 0, 7, 0)
-#define SYS_ID_AA64MMFR1_EL1		sys_reg(3, 0, 0, 7, 1)
-#define SYS_ID_AA64MMFR2_EL1		sys_reg(3, 0, 0, 7, 2)
-
-#define SYS_SCTLR_EL1			sys_reg(3, 0, 1, 0, 0)
 #define SYS_ACTLR_EL1			sys_reg(3, 0, 1, 0, 1)
-#define SYS_CPACR_EL1			sys_reg(3, 0, 1, 0, 2)
 #define SYS_RGSR_EL1			sys_reg(3, 0, 1, 0, 5)
 #define SYS_GCR_EL1			sys_reg(3, 0, 1, 0, 6)
 
-#define SYS_ZCR_EL1			sys_reg(3, 0, 1, 2, 0)
 #define SYS_TRFCR_EL1			sys_reg(3, 0, 1, 2, 1)
 
-#define SYS_TTBR0_EL1			sys_reg(3, 0, 2, 0, 0)
-#define SYS_TTBR1_EL1			sys_reg(3, 0, 2, 0, 1)
 #define SYS_TCR_EL1			sys_reg(3, 0, 2, 0, 2)
 
 #define SYS_APIAKEYLO_EL1		sys_reg(3, 0, 2, 1, 0)
@@ -233,7 +231,6 @@
 #define SYS_TFSR_EL1			sys_reg(3, 0, 5, 6, 0)
 #define SYS_TFSRE0_EL1			sys_reg(3, 0, 5, 6, 1)
 
-#define SYS_FAR_EL1			sys_reg(3, 0, 6, 0, 0)
 #define SYS_PAR_EL1			sys_reg(3, 0, 7, 4, 0)
 
 #define SYS_PAR_EL1_F			BIT(0)
@@ -395,12 +392,6 @@
 #define SYS_MAIR_EL1			sys_reg(3, 0, 10, 2, 0)
 #define SYS_AMAIR_EL1			sys_reg(3, 0, 10, 3, 0)
 
-#define SYS_LORSA_EL1			sys_reg(3, 0, 10, 4, 0)
-#define SYS_LOREA_EL1			sys_reg(3, 0, 10, 4, 1)
-#define SYS_LORN_EL1			sys_reg(3, 0, 10, 4, 2)
-#define SYS_LORC_EL1			sys_reg(3, 0, 10, 4, 3)
-#define SYS_LORID_EL1			sys_reg(3, 0, 10, 4, 7)
-
 #define SYS_VBAR_EL1			sys_reg(3, 0, 12, 0, 0)
 #define SYS_DISR_EL1			sys_reg(3, 0, 12, 1, 1)
 
@@ -432,23 +423,11 @@
 #define SYS_ICC_IGRPEN0_EL1		sys_reg(3, 0, 12, 12, 6)
 #define SYS_ICC_IGRPEN1_EL1		sys_reg(3, 0, 12, 12, 7)
 
-#define SYS_CONTEXTIDR_EL1		sys_reg(3, 0, 13, 0, 1)
-#define SYS_TPIDR_EL1			sys_reg(3, 0, 13, 0, 4)
-
-#define SYS_SCXTNUM_EL1			sys_reg(3, 0, 13, 0, 7)
-
 #define SYS_CNTKCTL_EL1			sys_reg(3, 0, 14, 1, 0)
 
 #define SYS_CCSIDR_EL1			sys_reg(3, 1, 0, 0, 0)
-#define SYS_CLIDR_EL1			sys_reg(3, 1, 0, 0, 1)
-#define SYS_GMID_EL1			sys_reg(3, 1, 0, 0, 4)
 #define SYS_AIDR_EL1			sys_reg(3, 1, 0, 0, 7)
 
-#define SYS_CSSELR_EL1			sys_reg(3, 2, 0, 0, 0)
-
-#define SYS_CTR_EL0			sys_reg(3, 3, 0, 0, 1)
-#define SYS_DCZID_EL0			sys_reg(3, 3, 0, 0, 7)
-
 #define SYS_RNDR_EL0			sys_reg(3, 3, 2, 4, 0)
 #define SYS_RNDRRS_EL0			sys_reg(3, 3, 2, 4, 1)
 
@@ -468,6 +447,7 @@
 
 #define SYS_TPIDR_EL0			sys_reg(3, 3, 13, 0, 2)
 #define SYS_TPIDRRO_EL0			sys_reg(3, 3, 13, 0, 3)
+#define SYS_TPIDR2_EL0			sys_reg(3, 3, 13, 0, 5)
 
 #define SYS_SCXTNUM_EL0			sys_reg(3, 3, 13, 0, 7)
 
@@ -535,9 +515,7 @@
 #define SYS_HFGRTR_EL2			sys_reg(3, 4, 1, 1, 4)
 #define SYS_HFGWTR_EL2			sys_reg(3, 4, 1, 1, 5)
 #define SYS_HFGITR_EL2			sys_reg(3, 4, 1, 1, 6)
-#define SYS_ZCR_EL2			sys_reg(3, 4, 1, 2, 0)
 #define SYS_TRFCR_EL2			sys_reg(3, 4, 1, 2, 1)
-#define SYS_DACR32_EL2			sys_reg(3, 4, 3, 0, 0)
 #define SYS_HDFGRTR_EL2			sys_reg(3, 4, 3, 1, 4)
 #define SYS_HDFGWTR_EL2			sys_reg(3, 4, 3, 1, 5)
 #define SYS_HAFGRTR_EL2			sys_reg(3, 4, 3, 1, 6)
@@ -548,7 +526,6 @@
 #define SYS_VSESR_EL2			sys_reg(3, 4, 5, 2, 3)
 #define SYS_FPEXC32_EL2			sys_reg(3, 4, 5, 3, 0)
 #define SYS_TFSR_EL2			sys_reg(3, 4, 5, 6, 0)
-#define SYS_FAR_EL2			sys_reg(3, 4, 6, 0, 0)
 
 #define SYS_VDISR_EL2			sys_reg(3, 4, 12, 1,  1)
 #define __SYS__AP0Rx_EL2(x)		sys_reg(3, 4, 12, 8, x)
@@ -594,8 +571,6 @@
 
 /* VHE encodings for architectural EL0/1 system registers */
 #define SYS_SCTLR_EL12			sys_reg(3, 5, 1, 0, 0)
-#define SYS_CPACR_EL12			sys_reg(3, 5, 1, 0, 2)
-#define SYS_ZCR_EL12			sys_reg(3, 5, 1, 2, 0)
 #define SYS_TTBR0_EL12			sys_reg(3, 5, 2, 0, 0)
 #define SYS_TTBR1_EL12			sys_reg(3, 5, 2, 0, 1)
 #define SYS_TCR_EL12			sys_reg(3, 5, 2, 0, 2)
@@ -605,11 +580,9 @@
 #define SYS_AFSR1_EL12			sys_reg(3, 5, 5, 1, 1)
 #define SYS_ESR_EL12			sys_reg(3, 5, 5, 2, 0)
 #define SYS_TFSR_EL12			sys_reg(3, 5, 5, 6, 0)
-#define SYS_FAR_EL12			sys_reg(3, 5, 6, 0, 0)
 #define SYS_MAIR_EL12			sys_reg(3, 5, 10, 2, 0)
 #define SYS_AMAIR_EL12			sys_reg(3, 5, 10, 3, 0)
 #define SYS_VBAR_EL12			sys_reg(3, 5, 12, 0, 0)
-#define SYS_CONTEXTIDR_EL12		sys_reg(3, 5, 13, 0, 1)
 #define SYS_CNTKCTL_EL12		sys_reg(3, 5, 14, 1, 0)
 #define SYS_CNTP_TVAL_EL02		sys_reg(3, 5, 14, 2, 0)
 #define SYS_CNTP_CTL_EL02		sys_reg(3, 5, 14, 2, 1)
@@ -619,31 +592,30 @@
 #define SYS_CNTV_CVAL_EL02		sys_reg(3, 5, 14, 3, 2)
 
 /* Common SCTLR_ELx flags. */
+#define SCTLR_ELx_ENTP2	(BIT(60))
 #define SCTLR_ELx_DSSBS	(BIT(44))
 #define SCTLR_ELx_ATA	(BIT(43))
 
-#define SCTLR_ELx_TCF_SHIFT	40
-#define SCTLR_ELx_TCF_NONE	(UL(0x0) << SCTLR_ELx_TCF_SHIFT)
-#define SCTLR_ELx_TCF_SYNC	(UL(0x1) << SCTLR_ELx_TCF_SHIFT)
-#define SCTLR_ELx_TCF_ASYNC	(UL(0x2) << SCTLR_ELx_TCF_SHIFT)
-#define SCTLR_ELx_TCF_ASYMM	(UL(0x3) << SCTLR_ELx_TCF_SHIFT)
-#define SCTLR_ELx_TCF_MASK	(UL(0x3) << SCTLR_ELx_TCF_SHIFT)
-
 #define SCTLR_ELx_ENIA_SHIFT	31
 
-#define SCTLR_ELx_ITFSB	(BIT(37))
-#define SCTLR_ELx_ENIA	(BIT(SCTLR_ELx_ENIA_SHIFT))
-#define SCTLR_ELx_ENIB	(BIT(30))
-#define SCTLR_ELx_ENDA	(BIT(27))
-#define SCTLR_ELx_EE    (BIT(25))
-#define SCTLR_ELx_IESB	(BIT(21))
-#define SCTLR_ELx_WXN	(BIT(19))
-#define SCTLR_ELx_ENDB	(BIT(13))
-#define SCTLR_ELx_I	(BIT(12))
-#define SCTLR_ELx_SA	(BIT(3))
-#define SCTLR_ELx_C	(BIT(2))
-#define SCTLR_ELx_A	(BIT(1))
-#define SCTLR_ELx_M	(BIT(0))
+#define SCTLR_ELx_ITFSB	 (BIT(37))
+#define SCTLR_ELx_ENIA	 (BIT(SCTLR_ELx_ENIA_SHIFT))
+#define SCTLR_ELx_ENIB	 (BIT(30))
+#define SCTLR_ELx_LSMAOE (BIT(29))
+#define SCTLR_ELx_nTLSMD (BIT(28))
+#define SCTLR_ELx_ENDA	 (BIT(27))
+#define SCTLR_ELx_EE     (BIT(25))
+#define SCTLR_ELx_EIS	 (BIT(22))
+#define SCTLR_ELx_IESB	 (BIT(21))
+#define SCTLR_ELx_TSCXT	 (BIT(20))
+#define SCTLR_ELx_WXN	 (BIT(19))
+#define SCTLR_ELx_ENDB	 (BIT(13))
+#define SCTLR_ELx_I	 (BIT(12))
+#define SCTLR_ELx_EOS	 (BIT(11))
+#define SCTLR_ELx_SA	 (BIT(3))
+#define SCTLR_ELx_C	 (BIT(2))
+#define SCTLR_ELx_A	 (BIT(1))
+#define SCTLR_ELx_M	 (BIT(0))
 
 /* SCTLR_EL2 specific flags. */
 #define SCTLR_EL2_RES1	((BIT(4))  | (BIT(5))  | (BIT(11)) | (BIT(16)) | \
@@ -665,34 +637,6 @@
 	(SCTLR_EL2_RES1 | ENDIAN_SET_EL2)
 
 /* SCTLR_EL1 specific flags. */
-#define SCTLR_EL1_EPAN		(BIT(57))
-#define SCTLR_EL1_ATA0		(BIT(42))
-
-#define SCTLR_EL1_TCF0_SHIFT	38
-#define SCTLR_EL1_TCF0_NONE	(UL(0x0) << SCTLR_EL1_TCF0_SHIFT)
-#define SCTLR_EL1_TCF0_SYNC	(UL(0x1) << SCTLR_EL1_TCF0_SHIFT)
-#define SCTLR_EL1_TCF0_ASYNC	(UL(0x2) << SCTLR_EL1_TCF0_SHIFT)
-#define SCTLR_EL1_TCF0_ASYMM	(UL(0x3) << SCTLR_EL1_TCF0_SHIFT)
-#define SCTLR_EL1_TCF0_MASK	(UL(0x3) << SCTLR_EL1_TCF0_SHIFT)
-
-#define SCTLR_EL1_BT1		(BIT(36))
-#define SCTLR_EL1_BT0		(BIT(35))
-#define SCTLR_EL1_UCI		(BIT(26))
-#define SCTLR_EL1_E0E		(BIT(24))
-#define SCTLR_EL1_SPAN		(BIT(23))
-#define SCTLR_EL1_NTWE		(BIT(18))
-#define SCTLR_EL1_NTWI		(BIT(16))
-#define SCTLR_EL1_UCT		(BIT(15))
-#define SCTLR_EL1_DZE		(BIT(14))
-#define SCTLR_EL1_UMA		(BIT(9))
-#define SCTLR_EL1_SED		(BIT(8))
-#define SCTLR_EL1_ITD		(BIT(7))
-#define SCTLR_EL1_CP15BEN	(BIT(5))
-#define SCTLR_EL1_SA0		(BIT(4))
-
-#define SCTLR_EL1_RES1	((BIT(11)) | (BIT(20)) | (BIT(22)) | (BIT(28)) | \
-			 (BIT(29)))
-
 #ifdef CONFIG_CPU_BIG_ENDIAN
 #define ENDIAN_SET_EL1		(SCTLR_EL1_E0E | SCTLR_ELx_EE)
 #else
@@ -700,13 +644,17 @@
 #endif
 
 #define INIT_SCTLR_EL1_MMU_OFF \
-	(ENDIAN_SET_EL1 | SCTLR_EL1_RES1)
+	(ENDIAN_SET_EL1 | SCTLR_EL1_LSMAOE | SCTLR_EL1_nTLSMD | \
+	 SCTLR_EL1_EIS  | SCTLR_EL1_TSCXT  | SCTLR_EL1_EOS)
 
 #define INIT_SCTLR_EL1_MMU_ON \
-	(SCTLR_ELx_M    | SCTLR_ELx_C    | SCTLR_ELx_SA   | SCTLR_EL1_SA0   | \
-	 SCTLR_EL1_SED  | SCTLR_ELx_I    | SCTLR_EL1_DZE  | SCTLR_EL1_UCT   | \
-	 SCTLR_EL1_NTWE | SCTLR_ELx_IESB | SCTLR_EL1_SPAN | SCTLR_ELx_ITFSB | \
-	 ENDIAN_SET_EL1 | SCTLR_EL1_UCI  | SCTLR_EL1_EPAN | SCTLR_EL1_RES1)
+	(SCTLR_ELx_M      | SCTLR_ELx_C      | SCTLR_ELx_SA    | \
+	 SCTLR_EL1_SA0    | SCTLR_EL1_SED    | SCTLR_ELx_I     | \
+	 SCTLR_EL1_DZE    | SCTLR_EL1_UCT    | SCTLR_EL1_nTWE  | \
+	 SCTLR_ELx_IESB   | SCTLR_EL1_SPAN   | SCTLR_ELx_ITFSB | \
+	 ENDIAN_SET_EL1   | SCTLR_EL1_UCI    | SCTLR_EL1_EPAN  | \
+	 SCTLR_EL1_LSMAOE | SCTLR_EL1_nTLSMD | SCTLR_EL1_EIS   | \
+	 SCTLR_EL1_TSCXT  | SCTLR_EL1_EOS)
 
 /* MAIR_ELx memory attributes (used by Linux) */
 #define MAIR_ATTR_DEVICE_nGnRnE		UL(0x00)
@@ -719,229 +667,31 @@
 /* Position the attr at the correct index */
 #define MAIR_ATTRIDX(attr, idx)		((attr) << ((idx) * 8))
 
-/* id_aa64isar0 */
-#define ID_AA64ISAR0_RNDR_SHIFT		60
-#define ID_AA64ISAR0_TLB_SHIFT		56
-#define ID_AA64ISAR0_TS_SHIFT		52
-#define ID_AA64ISAR0_FHM_SHIFT		48
-#define ID_AA64ISAR0_DP_SHIFT		44
-#define ID_AA64ISAR0_SM4_SHIFT		40
-#define ID_AA64ISAR0_SM3_SHIFT		36
-#define ID_AA64ISAR0_SHA3_SHIFT		32
-#define ID_AA64ISAR0_RDM_SHIFT		28
-#define ID_AA64ISAR0_ATOMICS_SHIFT	20
-#define ID_AA64ISAR0_CRC32_SHIFT	16
-#define ID_AA64ISAR0_SHA2_SHIFT		12
-#define ID_AA64ISAR0_SHA1_SHIFT		8
-#define ID_AA64ISAR0_AES_SHIFT		4
-
-#define ID_AA64ISAR0_TLB_RANGE_NI	0x0
-#define ID_AA64ISAR0_TLB_RANGE		0x2
-
-/* id_aa64isar1 */
-#define ID_AA64ISAR1_I8MM_SHIFT		52
-#define ID_AA64ISAR1_DGH_SHIFT		48
-#define ID_AA64ISAR1_BF16_SHIFT		44
-#define ID_AA64ISAR1_SPECRES_SHIFT	40
-#define ID_AA64ISAR1_SB_SHIFT		36
-#define ID_AA64ISAR1_FRINTTS_SHIFT	32
-#define ID_AA64ISAR1_GPI_SHIFT		28
-#define ID_AA64ISAR1_GPA_SHIFT		24
-#define ID_AA64ISAR1_LRCPC_SHIFT	20
-#define ID_AA64ISAR1_FCMA_SHIFT		16
-#define ID_AA64ISAR1_JSCVT_SHIFT	12
-#define ID_AA64ISAR1_API_SHIFT		8
-#define ID_AA64ISAR1_APA_SHIFT		4
-#define ID_AA64ISAR1_DPB_SHIFT		0
-
-#define ID_AA64ISAR1_APA_NI			0x0
-#define ID_AA64ISAR1_APA_ARCHITECTED		0x1
-#define ID_AA64ISAR1_APA_ARCH_EPAC		0x2
-#define ID_AA64ISAR1_APA_ARCH_EPAC2		0x3
-#define ID_AA64ISAR1_APA_ARCH_EPAC2_FPAC	0x4
-#define ID_AA64ISAR1_APA_ARCH_EPAC2_FPAC_CMB	0x5
-#define ID_AA64ISAR1_API_NI			0x0
-#define ID_AA64ISAR1_API_IMP_DEF		0x1
-#define ID_AA64ISAR1_API_IMP_DEF_EPAC		0x2
-#define ID_AA64ISAR1_API_IMP_DEF_EPAC2		0x3
-#define ID_AA64ISAR1_API_IMP_DEF_EPAC2_FPAC	0x4
-#define ID_AA64ISAR1_API_IMP_DEF_EPAC2_FPAC_CMB	0x5
-#define ID_AA64ISAR1_GPA_NI			0x0
-#define ID_AA64ISAR1_GPA_ARCHITECTED		0x1
-#define ID_AA64ISAR1_GPI_NI			0x0
-#define ID_AA64ISAR1_GPI_IMP_DEF		0x1
-
 /* id_aa64pfr0 */
-#define ID_AA64PFR0_CSV3_SHIFT		60
-#define ID_AA64PFR0_CSV2_SHIFT		56
-#define ID_AA64PFR0_DIT_SHIFT		48
-#define ID_AA64PFR0_AMU_SHIFT		44
-#define ID_AA64PFR0_MPAM_SHIFT		40
-#define ID_AA64PFR0_SEL2_SHIFT		36
-#define ID_AA64PFR0_SVE_SHIFT		32
-#define ID_AA64PFR0_RAS_SHIFT		28
-#define ID_AA64PFR0_GIC_SHIFT		24
-#define ID_AA64PFR0_ASIMD_SHIFT		20
-#define ID_AA64PFR0_FP_SHIFT		16
-#define ID_AA64PFR0_EL3_SHIFT		12
-#define ID_AA64PFR0_EL2_SHIFT		8
-#define ID_AA64PFR0_EL1_SHIFT		4
-#define ID_AA64PFR0_EL0_SHIFT		0
-
-#define ID_AA64PFR0_AMU			0x1
-#define ID_AA64PFR0_SVE			0x1
-#define ID_AA64PFR0_RAS_V1		0x1
-#define ID_AA64PFR0_RAS_V1P1		0x2
-#define ID_AA64PFR0_FP_NI		0xf
-#define ID_AA64PFR0_FP_SUPPORTED	0x0
-#define ID_AA64PFR0_ASIMD_NI		0xf
-#define ID_AA64PFR0_ASIMD_SUPPORTED	0x0
-#define ID_AA64PFR0_ELx_64BIT_ONLY	0x1
-#define ID_AA64PFR0_ELx_32BIT_64BIT	0x2
-
-/* id_aa64pfr1 */
-#define ID_AA64PFR1_MPAMFRAC_SHIFT	16
-#define ID_AA64PFR1_RASFRAC_SHIFT	12
-#define ID_AA64PFR1_MTE_SHIFT		8
-#define ID_AA64PFR1_SSBS_SHIFT		4
-#define ID_AA64PFR1_BT_SHIFT		0
-
-#define ID_AA64PFR1_SSBS_PSTATE_NI	0
-#define ID_AA64PFR1_SSBS_PSTATE_ONLY	1
-#define ID_AA64PFR1_SSBS_PSTATE_INSNS	2
-#define ID_AA64PFR1_BT_BTI		0x1
-
-#define ID_AA64PFR1_MTE_NI		0x0
-#define ID_AA64PFR1_MTE_EL0		0x1
-#define ID_AA64PFR1_MTE			0x2
-#define ID_AA64PFR1_MTE_ASYMM		0x3
-
-/* id_aa64zfr0 */
-#define ID_AA64ZFR0_F64MM_SHIFT		56
-#define ID_AA64ZFR0_F32MM_SHIFT		52
-#define ID_AA64ZFR0_I8MM_SHIFT		44
-#define ID_AA64ZFR0_SM4_SHIFT		40
-#define ID_AA64ZFR0_SHA3_SHIFT		32
-#define ID_AA64ZFR0_BF16_SHIFT		20
-#define ID_AA64ZFR0_BITPERM_SHIFT	16
-#define ID_AA64ZFR0_AES_SHIFT		4
-#define ID_AA64ZFR0_SVEVER_SHIFT	0
-
-#define ID_AA64ZFR0_F64MM		0x1
-#define ID_AA64ZFR0_F32MM		0x1
-#define ID_AA64ZFR0_I8MM		0x1
-#define ID_AA64ZFR0_BF16		0x1
-#define ID_AA64ZFR0_SM4			0x1
-#define ID_AA64ZFR0_SHA3		0x1
-#define ID_AA64ZFR0_BITPERM		0x1
-#define ID_AA64ZFR0_AES			0x1
-#define ID_AA64ZFR0_AES_PMULL		0x2
-#define ID_AA64ZFR0_SVEVER_SVE2		0x1
+#define ID_AA64PFR0_EL1_ELx_64BIT_ONLY		0x1
+#define ID_AA64PFR0_EL1_ELx_32BIT_64BIT		0x2
 
 /* id_aa64mmfr0 */
-#define ID_AA64MMFR0_ECV_SHIFT		60
-#define ID_AA64MMFR0_FGT_SHIFT		56
-#define ID_AA64MMFR0_EXS_SHIFT		44
-#define ID_AA64MMFR0_TGRAN4_2_SHIFT	40
-#define ID_AA64MMFR0_TGRAN64_2_SHIFT	36
-#define ID_AA64MMFR0_TGRAN16_2_SHIFT	32
-#define ID_AA64MMFR0_TGRAN4_SHIFT	28
-#define ID_AA64MMFR0_TGRAN64_SHIFT	24
-#define ID_AA64MMFR0_TGRAN16_SHIFT	20
-#define ID_AA64MMFR0_BIGENDEL0_SHIFT	16
-#define ID_AA64MMFR0_SNSMEM_SHIFT	12
-#define ID_AA64MMFR0_BIGENDEL_SHIFT	8
-#define ID_AA64MMFR0_ASID_SHIFT		4
-#define ID_AA64MMFR0_PARANGE_SHIFT	0
-
-#define ID_AA64MMFR0_ASID_8		0x0
-#define ID_AA64MMFR0_ASID_16		0x2
-
-#define ID_AA64MMFR0_TGRAN4_NI			0xf
-#define ID_AA64MMFR0_TGRAN4_SUPPORTED_MIN	0x0
-#define ID_AA64MMFR0_TGRAN4_SUPPORTED_MAX	0x7
-#define ID_AA64MMFR0_TGRAN64_NI			0xf
-#define ID_AA64MMFR0_TGRAN64_SUPPORTED_MIN	0x0
-#define ID_AA64MMFR0_TGRAN64_SUPPORTED_MAX	0x7
-#define ID_AA64MMFR0_TGRAN16_NI			0x0
-#define ID_AA64MMFR0_TGRAN16_SUPPORTED_MIN	0x1
-#define ID_AA64MMFR0_TGRAN16_SUPPORTED_MAX	0xf
-
-#define ID_AA64MMFR0_PARANGE_32		0x0
-#define ID_AA64MMFR0_PARANGE_36		0x1
-#define ID_AA64MMFR0_PARANGE_40		0x2
-#define ID_AA64MMFR0_PARANGE_42		0x3
-#define ID_AA64MMFR0_PARANGE_44		0x4
-#define ID_AA64MMFR0_PARANGE_48		0x5
-#define ID_AA64MMFR0_PARANGE_52		0x6
+#define ID_AA64MMFR0_EL1_TGRAN4_SUPPORTED_MIN	0x0
+#define ID_AA64MMFR0_EL1_TGRAN4_SUPPORTED_MAX	0x7
+#define ID_AA64MMFR0_EL1_TGRAN64_SUPPORTED_MIN	0x0
+#define ID_AA64MMFR0_EL1_TGRAN64_SUPPORTED_MAX	0x7
+#define ID_AA64MMFR0_EL1_TGRAN16_SUPPORTED_MIN	0x1
+#define ID_AA64MMFR0_EL1_TGRAN16_SUPPORTED_MAX	0xf
 
 #define ARM64_MIN_PARANGE_BITS		32
 
-#define ID_AA64MMFR0_TGRAN_2_SUPPORTED_DEFAULT	0x0
-#define ID_AA64MMFR0_TGRAN_2_SUPPORTED_NONE	0x1
-#define ID_AA64MMFR0_TGRAN_2_SUPPORTED_MIN	0x2
-#define ID_AA64MMFR0_TGRAN_2_SUPPORTED_MAX	0x7
+#define ID_AA64MMFR0_EL1_TGRAN_2_SUPPORTED_DEFAULT	0x0
+#define ID_AA64MMFR0_EL1_TGRAN_2_SUPPORTED_NONE		0x1
+#define ID_AA64MMFR0_EL1_TGRAN_2_SUPPORTED_MIN		0x2
+#define ID_AA64MMFR0_EL1_TGRAN_2_SUPPORTED_MAX		0x7
 
 #ifdef CONFIG_ARM64_PA_BITS_52
-#define ID_AA64MMFR0_PARANGE_MAX	ID_AA64MMFR0_PARANGE_52
+#define ID_AA64MMFR0_EL1_PARANGE_MAX	ID_AA64MMFR0_EL1_PARANGE_52
 #else
-#define ID_AA64MMFR0_PARANGE_MAX	ID_AA64MMFR0_PARANGE_48
+#define ID_AA64MMFR0_EL1_PARANGE_MAX	ID_AA64MMFR0_EL1_PARANGE_48
 #endif
 
-/* id_aa64mmfr1 */
-#define ID_AA64MMFR1_ETS_SHIFT		36
-#define ID_AA64MMFR1_TWED_SHIFT		32
-#define ID_AA64MMFR1_XNX_SHIFT		28
-#define ID_AA64MMFR1_SPECSEI_SHIFT	24
-#define ID_AA64MMFR1_PAN_SHIFT		20
-#define ID_AA64MMFR1_LOR_SHIFT		16
-#define ID_AA64MMFR1_HPD_SHIFT		12
-#define ID_AA64MMFR1_VHE_SHIFT		8
-#define ID_AA64MMFR1_VMIDBITS_SHIFT	4
-#define ID_AA64MMFR1_HADBS_SHIFT	0
-
-#define ID_AA64MMFR1_VMIDBITS_8		0
-#define ID_AA64MMFR1_VMIDBITS_16	2
-
-/* id_aa64mmfr2 */
-#define ID_AA64MMFR2_E0PD_SHIFT		60
-#define ID_AA64MMFR2_EVT_SHIFT		56
-#define ID_AA64MMFR2_BBM_SHIFT		52
-#define ID_AA64MMFR2_TTL_SHIFT		48
-#define ID_AA64MMFR2_FWB_SHIFT		40
-#define ID_AA64MMFR2_IDS_SHIFT		36
-#define ID_AA64MMFR2_AT_SHIFT		32
-#define ID_AA64MMFR2_ST_SHIFT		28
-#define ID_AA64MMFR2_NV_SHIFT		24
-#define ID_AA64MMFR2_CCIDX_SHIFT	20
-#define ID_AA64MMFR2_LVA_SHIFT		16
-#define ID_AA64MMFR2_IESB_SHIFT		12
-#define ID_AA64MMFR2_LSM_SHIFT		8
-#define ID_AA64MMFR2_UAO_SHIFT		4
-#define ID_AA64MMFR2_CNP_SHIFT		0
-
-/* id_aa64dfr0 */
-#define ID_AA64DFR0_MTPMU_SHIFT		48
-#define ID_AA64DFR0_TRBE_SHIFT		44
-#define ID_AA64DFR0_TRACE_FILT_SHIFT	40
-#define ID_AA64DFR0_DOUBLELOCK_SHIFT	36
-#define ID_AA64DFR0_PMSVER_SHIFT	32
-#define ID_AA64DFR0_CTX_CMPS_SHIFT	28
-#define ID_AA64DFR0_WRPS_SHIFT		20
-#define ID_AA64DFR0_BRPS_SHIFT		12
-#define ID_AA64DFR0_PMUVER_SHIFT	8
-#define ID_AA64DFR0_TRACEVER_SHIFT	4
-#define ID_AA64DFR0_DEBUGVER_SHIFT	0
-
-#define ID_AA64DFR0_PMUVER_8_0		0x1
-#define ID_AA64DFR0_PMUVER_8_1		0x4
-#define ID_AA64DFR0_PMUVER_8_4		0x5
-#define ID_AA64DFR0_PMUVER_8_5		0x6
-#define ID_AA64DFR0_PMUVER_IMP_DEF	0xf
-
-#define ID_AA64DFR0_PMSVER_8_2		0x1
-#define ID_AA64DFR0_PMSVER_8_3		0x2
-
 #define ID_DFR0_PERFMON_SHIFT		24
 
 #define ID_DFR0_PERFMON_8_0		0x3
@@ -1049,44 +799,33 @@
 #define ID_PFR1_PROGMOD_SHIFT		0
 
 #if defined(CONFIG_ARM64_4K_PAGES)
-#define ID_AA64MMFR0_TGRAN_SHIFT		ID_AA64MMFR0_TGRAN4_SHIFT
-#define ID_AA64MMFR0_TGRAN_SUPPORTED_MIN	ID_AA64MMFR0_TGRAN4_SUPPORTED_MIN
-#define ID_AA64MMFR0_TGRAN_SUPPORTED_MAX	ID_AA64MMFR0_TGRAN4_SUPPORTED_MAX
-#define ID_AA64MMFR0_TGRAN_2_SHIFT		ID_AA64MMFR0_TGRAN4_2_SHIFT
+#define ID_AA64MMFR0_EL1_TGRAN_SHIFT		ID_AA64MMFR0_EL1_TGRAN4_SHIFT
+#define ID_AA64MMFR0_EL1_TGRAN_SUPPORTED_MIN	ID_AA64MMFR0_EL1_TGRAN4_SUPPORTED_MIN
+#define ID_AA64MMFR0_EL1_TGRAN_SUPPORTED_MAX	ID_AA64MMFR0_EL1_TGRAN4_SUPPORTED_MAX
+#define ID_AA64MMFR0_EL1_TGRAN_2_SHIFT		ID_AA64MMFR0_EL1_TGRAN4_2_SHIFT
 #elif defined(CONFIG_ARM64_16K_PAGES)
-#define ID_AA64MMFR0_TGRAN_SHIFT		ID_AA64MMFR0_TGRAN16_SHIFT
-#define ID_AA64MMFR0_TGRAN_SUPPORTED_MIN	ID_AA64MMFR0_TGRAN16_SUPPORTED_MIN
-#define ID_AA64MMFR0_TGRAN_SUPPORTED_MAX	ID_AA64MMFR0_TGRAN16_SUPPORTED_MAX
-#define ID_AA64MMFR0_TGRAN_2_SHIFT		ID_AA64MMFR0_TGRAN16_2_SHIFT
+#define ID_AA64MMFR0_EL1_TGRAN_SHIFT		ID_AA64MMFR0_EL1_TGRAN16_SHIFT
+#define ID_AA64MMFR0_EL1_TGRAN_SUPPORTED_MIN	ID_AA64MMFR0_EL1_TGRAN16_SUPPORTED_MIN
+#define ID_AA64MMFR0_EL1_TGRAN_SUPPORTED_MAX	ID_AA64MMFR0_EL1_TGRAN16_SUPPORTED_MAX
+#define ID_AA64MMFR0_EL1_TGRAN_2_SHIFT		ID_AA64MMFR0_EL1_TGRAN16_2_SHIFT
 #elif defined(CONFIG_ARM64_64K_PAGES)
-#define ID_AA64MMFR0_TGRAN_SHIFT		ID_AA64MMFR0_TGRAN64_SHIFT
-#define ID_AA64MMFR0_TGRAN_SUPPORTED_MIN	ID_AA64MMFR0_TGRAN64_SUPPORTED_MIN
-#define ID_AA64MMFR0_TGRAN_SUPPORTED_MAX	ID_AA64MMFR0_TGRAN64_SUPPORTED_MAX
-#define ID_AA64MMFR0_TGRAN_2_SHIFT		ID_AA64MMFR0_TGRAN64_2_SHIFT
+#define ID_AA64MMFR0_EL1_TGRAN_SHIFT		ID_AA64MMFR0_EL1_TGRAN64_SHIFT
+#define ID_AA64MMFR0_EL1_TGRAN_SUPPORTED_MIN	ID_AA64MMFR0_EL1_TGRAN64_SUPPORTED_MIN
+#define ID_AA64MMFR0_EL1_TGRAN_SUPPORTED_MAX	ID_AA64MMFR0_EL1_TGRAN64_SUPPORTED_MAX
+#define ID_AA64MMFR0_EL1_TGRAN_2_SHIFT		ID_AA64MMFR0_EL1_TGRAN64_2_SHIFT
 #endif
 
 #define MVFR2_FPMISC_SHIFT		4
 #define MVFR2_SIMDMISC_SHIFT		0
 
-#define DCZID_DZP_SHIFT			4
-#define DCZID_BS_SHIFT			0
+#define CPACR_EL1_FPEN_EL1EN	(BIT(20)) /* enable EL1 access */
+#define CPACR_EL1_FPEN_EL0EN	(BIT(21)) /* enable EL0 access, if EL1EN set */
 
-/*
- * The ZCR_ELx_LEN_* definitions intentionally include bits [8:4] which
- * are reserved by the SVE architecture for future expansion of the LEN
- * field, with compatible semantics.
- */
-#define ZCR_ELx_LEN_SHIFT	0
-#define ZCR_ELx_LEN_SIZE	9
-#define ZCR_ELx_LEN_MASK	0x1ff
+#define CPACR_EL1_SMEN_EL1EN	(BIT(24)) /* enable EL1 access */
+#define CPACR_EL1_SMEN_EL0EN	(BIT(25)) /* enable EL0 access, if EL1EN set */
 
 #define CPACR_EL1_ZEN_EL1EN	(BIT(16)) /* enable EL1 access */
 #define CPACR_EL1_ZEN_EL0EN	(BIT(17)) /* enable EL0 access, if EL1EN set */
-#define CPACR_EL1_ZEN		(CPACR_EL1_ZEN_EL1EN | CPACR_EL1_ZEN_EL0EN)
-
-/* TCR EL1 Bit Definitions */
-#define SYS_TCR_EL1_TCMA1	(BIT(58))
-#define SYS_TCR_EL1_TCMA0	(BIT(57))
 
 /* GCR_EL1 Definitions */
 #define SYS_GCR_EL1_RRND	(BIT(16))
@@ -1113,8 +852,8 @@
 #define SYS_RGSR_EL1_SEED_MASK	0xffffUL
 
 /* GMID_EL1 field definitions */
-#define SYS_GMID_EL1_BS_SHIFT	0
-#define SYS_GMID_EL1_BS_SIZE	4
+#define GMID_EL1_BS_SHIFT	0
+#define GMID_EL1_BS_SIZE	4
 
 /* TFSR{,E0}_EL1 bit definitions */
 #define SYS_TFSR_EL1_TF0_SHIFT	0
@@ -1126,6 +865,7 @@
 #define SYS_MPIDR_SAFE_VAL	(BIT(31))
 
 #define TRFCR_ELx_TS_SHIFT		5
+#define TRFCR_ELx_TS_MASK		((0x3UL) << TRFCR_ELx_TS_SHIFT)
 #define TRFCR_ELx_TS_VIRTUAL		((0x1UL) << TRFCR_ELx_TS_SHIFT)
 #define TRFCR_ELx_TS_GUEST_PHYSICAL	((0x2UL) << TRFCR_ELx_TS_SHIFT)
 #define TRFCR_ELx_TS_PHYSICAL		((0x3UL) << TRFCR_ELx_TS_SHIFT)
@@ -1133,7 +873,6 @@
 #define TRFCR_ELx_ExTRE			BIT(1)
 #define TRFCR_ELx_E0TRE			BIT(0)
 
-
 /* GIC Hypervisor interface registers */
 /* ICH_MISR_EL2 bit definitions */
 #define ICH_MISR_EOI		(1 << 0)
@@ -1196,6 +935,12 @@
 #define ICH_VTR_TDS_SHIFT	19
 #define ICH_VTR_TDS_MASK	(1 << ICH_VTR_TDS_SHIFT)
 
+/* HFG[WR]TR_EL2 bit definitions */
+#define HFGxTR_EL2_nTPIDR2_EL0_SHIFT	55
+#define HFGxTR_EL2_nTPIDR2_EL0_MASK	BIT_MASK(HFGxTR_EL2_nTPIDR2_EL0_SHIFT)
+#define HFGxTR_EL2_nSMPRI_EL1_SHIFT	54
+#define HFGxTR_EL2_nSMPRI_EL1_MASK	BIT_MASK(HFGxTR_EL2_nSMPRI_EL1_SHIFT)
+
 #define ARM64_FEATURE_FIELD_BITS	4
 
 /* Create a mask for the feature bits of the specified feature. */
@@ -1213,6 +958,7 @@
 
 #else
 
+#include <linux/bitfield.h>
 #include <linux/build_bug.h>
 #include <linux/types.h>
 #include <asm/alternative.h>
@@ -1306,6 +1052,15 @@
 	par;								\
 })
 
+#define SYS_FIELD_GET(reg, field, val)		\
+		 FIELD_GET(reg##_##field##_MASK, val)
+
+#define SYS_FIELD_PREP(reg, field, val)		\
+		 FIELD_PREP(reg##_##field##_MASK, val)
+
+#define SYS_FIELD_PREP_ENUM(reg, field, val)		\
+		 FIELD_PREP(reg##_##field##_MASK, reg##_##field##_##val)
+
 #endif
 
 #endif	/* __ASM_SYSREG_H */
diff --git a/arch/arm64/include/asm/system_misc.h b/arch/arm64/include/asm/system_misc.h
index 305a7157c6a6..c34344256762 100644
--- a/arch/arm64/include/asm/system_misc.h
+++ b/arch/arm64/include/asm/system_misc.h
@@ -18,14 +18,14 @@
 
 struct pt_regs;
 
-void die(const char *msg, struct pt_regs *regs, int err);
+void die(const char *msg, struct pt_regs *regs, long err);
 
 struct siginfo;
 void arm64_notify_die(const char *str, struct pt_regs *regs,
 		      int signo, int sicode, unsigned long far,
-		      int err);
+		      unsigned long err);
 
-void hook_debug_fault_code(int nr, int (*fn)(unsigned long, unsigned int,
+void hook_debug_fault_code(int nr, int (*fn)(unsigned long, unsigned long,
 					     struct pt_regs *),
 			   int sig, int code, const char *name);
 
diff --git a/arch/arm64/include/asm/thread_info.h b/arch/arm64/include/asm/thread_info.h
index e1317b7c4525..848739c15de8 100644
--- a/arch/arm64/include/asm/thread_info.h
+++ b/arch/arm64/include/asm/thread_info.h
@@ -82,6 +82,8 @@ int arch_dup_task_struct(struct task_struct *dst,
 #define TIF_SVE_VL_INHERIT	24	/* Inherit SVE vl_onexec across exec */
 #define TIF_SSBD		25	/* Wants SSB mitigation */
 #define TIF_TAGGED_ADDR		26	/* Allow tagged user addresses */
+#define TIF_SME			27	/* SME in use */
+#define TIF_SME_VL_INHERIT	28	/* Inherit SME vl_onexec across exec */
 
 #define _TIF_SIGPENDING		(1 << TIF_SIGPENDING)
 #define _TIF_NEED_RESCHED	(1 << TIF_NEED_RESCHED)
diff --git a/arch/arm64/include/asm/topology.h b/arch/arm64/include/asm/topology.h
index ec2db3419c41..9fab663dd2de 100644
--- a/arch/arm64/include/asm/topology.h
+++ b/arch/arm64/include/asm/topology.h
@@ -24,6 +24,10 @@ void update_freq_counters_refs(void);
 #define arch_scale_freq_capacity topology_get_freq_scale
 #define arch_scale_freq_invariant topology_scale_freq_invariant
 
+#ifdef CONFIG_ACPI_CPPC_LIB
+#define arch_init_invariance_cppc topology_init_cpu_capacity_cppc
+#endif
+
 /* Replace task scheduler's default cpu-invariant accounting */
 #define arch_scale_cpu_capacity topology_get_cpu_scale
 
@@ -32,7 +36,7 @@ void update_freq_counters_refs(void);
 
 /* Replace task scheduler's default thermal pressure API */
 #define arch_scale_thermal_pressure topology_get_thermal_pressure
-#define arch_set_thermal_pressure   topology_set_thermal_pressure
+#define arch_update_thermal_pressure	topology_update_thermal_pressure
 
 #include <asm-generic/topology.h>
 
diff --git a/arch/arm64/include/asm/traps.h b/arch/arm64/include/asm/traps.h
index 54f32a0675df..6e5826470bea 100644
--- a/arch/arm64/include/asm/traps.h
+++ b/arch/arm64/include/asm/traps.h
@@ -24,7 +24,7 @@ struct undef_hook {
 
 void register_undef_hook(struct undef_hook *hook);
 void unregister_undef_hook(struct undef_hook *hook);
-void force_signal_inject(int signal, int code, unsigned long address, unsigned int err);
+void force_signal_inject(int signal, int code, unsigned long address, unsigned long err);
 void arm64_notify_segfault(unsigned long addr);
 void arm64_force_sig_fault(int signo, int code, unsigned long far, const char *str);
 void arm64_force_sig_mceerr(int code, unsigned long far, short lsb, const char *str);
@@ -57,7 +57,7 @@ static inline int in_entry_text(unsigned long ptr)
  * errors share the same encoding as an all-zeros encoding from a CPU that
  * doesn't support RAS.
  */
-static inline bool arm64_is_ras_serror(u32 esr)
+static inline bool arm64_is_ras_serror(unsigned long esr)
 {
 	WARN_ON(preemptible());
 
@@ -77,9 +77,9 @@ static inline bool arm64_is_ras_serror(u32 esr)
  * We treat them as Uncontainable.
  * Non-RAS SError's are reported as Uncontained/Uncategorized.
  */
-static inline u32 arm64_ras_serror_get_severity(u32 esr)
+static inline unsigned long arm64_ras_serror_get_severity(unsigned long esr)
 {
-	u32 aet = esr & ESR_ELx_AET;
+	unsigned long aet = esr & ESR_ELx_AET;
 
 	if (!arm64_is_ras_serror(esr)) {
 		/* Not a RAS error, we can't interpret the ESR. */
@@ -98,6 +98,6 @@ static inline u32 arm64_ras_serror_get_severity(u32 esr)
 	return aet;
 }
 
-bool arm64_is_fatal_ras_serror(struct pt_regs *regs, unsigned int esr);
-void __noreturn arm64_serror_panic(struct pt_regs *regs, u32 esr);
+bool arm64_is_fatal_ras_serror(struct pt_regs *regs, unsigned long esr);
+void __noreturn arm64_serror_panic(struct pt_regs *regs, unsigned long esr);
 #endif
diff --git a/arch/arm64/include/asm/uaccess.h b/arch/arm64/include/asm/uaccess.h
index 3a5ff5e20586..5c7b2f9d5913 100644
--- a/arch/arm64/include/asm/uaccess.h
+++ b/arch/arm64/include/asm/uaccess.h
@@ -26,7 +26,7 @@
 #include <asm/memory.h>
 #include <asm/extable.h>
 
-#define HAVE_GET_KERNEL_NOFAULT
+static inline int __access_ok(const void __user *ptr, unsigned long size);
 
 /*
  * Test whether a block of memory is a valid user space address.
@@ -35,10 +35,8 @@
  * This is equivalent to the following test:
  * (u65)addr + (u65)size <= (u65)TASK_SIZE_MAX
  */
-static inline unsigned long __range_ok(const void __user *addr, unsigned long size)
+static inline int access_ok(const void __user *addr, unsigned long size)
 {
-	unsigned long ret, limit = TASK_SIZE_MAX - 1;
-
 	/*
 	 * Asynchronous I/O running in a kernel thread does not have the
 	 * TIF_TAGGED_ADDR flag of the process owning the mm, so always untag
@@ -48,28 +46,11 @@ static inline unsigned long __range_ok(const void __user *addr, unsigned long si
 	    (current->flags & PF_KTHREAD || test_thread_flag(TIF_TAGGED_ADDR)))
 		addr = untagged_addr(addr);
 
-	__chk_user_ptr(addr);
-	asm volatile(
-	// A + B <= C + 1 for all A,B,C, in four easy steps:
-	// 1: X = A + B; X' = X % 2^64
-	"	adds	%0, %3, %2\n"
-	// 2: Set C = 0 if X > 2^64, to guarantee X' > C in step 4
-	"	csel	%1, xzr, %1, hi\n"
-	// 3: Set X' = ~0 if X >= 2^64. For X == 2^64, this decrements X'
-	//    to compensate for the carry flag being set in step 4. For
-	//    X > 2^64, X' merely has to remain nonzero, which it does.
-	"	csinv	%0, %0, xzr, cc\n"
-	// 4: For X < 2^64, this gives us X' - C - 1 <= 0, where the -1
-	//    comes from the carry in being clear. Otherwise, we are
-	//    testing X' - C == 0, subject to the previous adjustments.
-	"	sbcs	xzr, %0, %1\n"
-	"	cset	%0, ls\n"
-	: "=&r" (ret), "+r" (limit) : "Ir" (size), "0" (addr) : "cc");
-
-	return ret;
+	return likely(__access_ok(addr, size));
 }
+#define access_ok access_ok
 
-#define access_ok(addr, size)	__range_ok(addr, size)
+#include <asm-generic/access_ok.h>
 
 /*
  * User access enabling/disabling.
@@ -222,9 +203,11 @@ static inline void uaccess_enable_privileged(void)
 }
 
 /*
- * Sanitise a uaccess pointer such that it becomes NULL if above the maximum
- * user address. In case the pointer is tagged (has the top byte set), untag
- * the pointer before checking.
+ * Sanitize a uaccess pointer such that it cannot reach any kernel address.
+ *
+ * Clearing bit 55 ensures the pointer cannot address any portion of the TTBR1
+ * address range (i.e. any kernel address), and either the pointer falls within
+ * the TTBR0 address range or must cause a fault.
  */
 #define uaccess_mask_ptr(ptr) (__typeof__(ptr))__uaccess_mask_ptr(ptr)
 static inline void __user *__uaccess_mask_ptr(const void __user *ptr)
@@ -232,14 +215,12 @@ static inline void __user *__uaccess_mask_ptr(const void __user *ptr)
 	void __user *safe_ptr;
 
 	asm volatile(
-	"	bics	xzr, %3, %2\n"
-	"	csel	%0, %1, xzr, eq\n"
-	: "=&r" (safe_ptr)
-	: "r" (ptr), "r" (TASK_SIZE_MAX - 1),
-	  "r" (untagged_addr(ptr))
-	: "cc");
-
-	csdb();
+	"	bic	%0, %1, %2\n"
+	: "=r" (safe_ptr)
+	: "r" (ptr),
+	  "i" (BIT(55))
+	);
+
 	return safe_ptr;
 }
 
@@ -251,34 +232,34 @@ static inline void __user *__uaccess_mask_ptr(const void __user *ptr)
  * The "__xxx_error" versions set the third argument to -EFAULT if an error
  * occurs, and leave it unchanged on success.
  */
-#define __get_mem_asm(load, reg, x, addr, err)				\
+#define __get_mem_asm(load, reg, x, addr, err, type)			\
 	asm volatile(							\
 	"1:	" load "	" reg "1, [%2]\n"			\
 	"2:\n"								\
-	_ASM_EXTABLE_UACCESS_ERR_ZERO(1b, 2b, %w0, %w1)			\
+	_ASM_EXTABLE_##type##ACCESS_ERR_ZERO(1b, 2b, %w0, %w1)		\
 	: "+r" (err), "=&r" (x)						\
 	: "r" (addr))
 
-#define __raw_get_mem(ldr, x, ptr, err)					\
-do {									\
-	unsigned long __gu_val;						\
-	switch (sizeof(*(ptr))) {					\
-	case 1:								\
-		__get_mem_asm(ldr "b", "%w", __gu_val, (ptr), (err));	\
-		break;							\
-	case 2:								\
-		__get_mem_asm(ldr "h", "%w", __gu_val, (ptr), (err));	\
-		break;							\
-	case 4:								\
-		__get_mem_asm(ldr, "%w", __gu_val, (ptr), (err));	\
-		break;							\
-	case 8:								\
-		__get_mem_asm(ldr, "%x",  __gu_val, (ptr), (err));	\
-		break;							\
-	default:							\
-		BUILD_BUG();						\
-	}								\
-	(x) = (__force __typeof__(*(ptr)))__gu_val;			\
+#define __raw_get_mem(ldr, x, ptr, err, type)					\
+do {										\
+	unsigned long __gu_val;							\
+	switch (sizeof(*(ptr))) {						\
+	case 1:									\
+		__get_mem_asm(ldr "b", "%w", __gu_val, (ptr), (err), type);	\
+		break;								\
+	case 2:									\
+		__get_mem_asm(ldr "h", "%w", __gu_val, (ptr), (err), type);	\
+		break;								\
+	case 4:									\
+		__get_mem_asm(ldr, "%w", __gu_val, (ptr), (err), type);		\
+		break;								\
+	case 8:									\
+		__get_mem_asm(ldr, "%x",  __gu_val, (ptr), (err), type);	\
+		break;								\
+	default:								\
+		BUILD_BUG();							\
+	}									\
+	(x) = (__force __typeof__(*(ptr)))__gu_val;				\
 } while (0)
 
 /*
@@ -293,7 +274,7 @@ do {									\
 	__chk_user_ptr(ptr);						\
 									\
 	uaccess_ttbr0_enable();						\
-	__raw_get_mem("ldtr", __rgu_val, __rgu_ptr, err);		\
+	__raw_get_mem("ldtr", __rgu_val, __rgu_ptr, err, U);		\
 	uaccess_ttbr0_disable();					\
 									\
 	(x) = __rgu_val;						\
@@ -333,40 +314,40 @@ do {									\
 									\
 	__uaccess_enable_tco_async();					\
 	__raw_get_mem("ldr", *((type *)(__gkn_dst)),			\
-		      (__force type *)(__gkn_src), __gkn_err);		\
+		      (__force type *)(__gkn_src), __gkn_err, K);	\
 	__uaccess_disable_tco_async();					\
 									\
 	if (unlikely(__gkn_err))					\
 		goto err_label;						\
 } while (0)
 
-#define __put_mem_asm(store, reg, x, addr, err)				\
+#define __put_mem_asm(store, reg, x, addr, err, type)			\
 	asm volatile(							\
 	"1:	" store "	" reg "1, [%2]\n"			\
 	"2:\n"								\
-	_ASM_EXTABLE_UACCESS_ERR(1b, 2b, %w0)				\
+	_ASM_EXTABLE_##type##ACCESS_ERR(1b, 2b, %w0)			\
 	: "+r" (err)							\
 	: "r" (x), "r" (addr))
 
-#define __raw_put_mem(str, x, ptr, err)					\
-do {									\
-	__typeof__(*(ptr)) __pu_val = (x);				\
-	switch (sizeof(*(ptr))) {					\
-	case 1:								\
-		__put_mem_asm(str "b", "%w", __pu_val, (ptr), (err));	\
-		break;							\
-	case 2:								\
-		__put_mem_asm(str "h", "%w", __pu_val, (ptr), (err));	\
-		break;							\
-	case 4:								\
-		__put_mem_asm(str, "%w", __pu_val, (ptr), (err));	\
-		break;							\
-	case 8:								\
-		__put_mem_asm(str, "%x", __pu_val, (ptr), (err));	\
-		break;							\
-	default:							\
-		BUILD_BUG();						\
-	}								\
+#define __raw_put_mem(str, x, ptr, err, type)					\
+do {										\
+	__typeof__(*(ptr)) __pu_val = (x);					\
+	switch (sizeof(*(ptr))) {						\
+	case 1:									\
+		__put_mem_asm(str "b", "%w", __pu_val, (ptr), (err), type);	\
+		break;								\
+	case 2:									\
+		__put_mem_asm(str "h", "%w", __pu_val, (ptr), (err), type);	\
+		break;								\
+	case 4:									\
+		__put_mem_asm(str, "%w", __pu_val, (ptr), (err), type);		\
+		break;								\
+	case 8:									\
+		__put_mem_asm(str, "%x", __pu_val, (ptr), (err), type);		\
+		break;								\
+	default:								\
+		BUILD_BUG();							\
+	}									\
 } while (0)
 
 /*
@@ -381,7 +362,7 @@ do {									\
 	__chk_user_ptr(__rpu_ptr);					\
 									\
 	uaccess_ttbr0_enable();						\
-	__raw_put_mem("sttr", __rpu_val, __rpu_ptr, err);		\
+	__raw_put_mem("sttr", __rpu_val, __rpu_ptr, err, U);		\
 	uaccess_ttbr0_disable();					\
 } while (0)
 
@@ -419,7 +400,7 @@ do {									\
 									\
 	__uaccess_enable_tco_async();					\
 	__raw_put_mem("str", *((type *)(__pkn_src)),			\
-		      (__force type *)(__pkn_dst), __pkn_err);		\
+		      (__force type *)(__pkn_dst), __pkn_err, K);	\
 	__uaccess_disable_tco_async();					\
 									\
 	if (unlikely(__pkn_err))					\
@@ -479,4 +460,19 @@ static inline int __copy_from_user_flushcache(void *dst, const void __user *src,
 }
 #endif
 
+#ifdef CONFIG_ARCH_HAS_SUBPAGE_FAULTS
+
+/*
+ * Return 0 on success, the number of bytes not probed otherwise.
+ */
+static inline size_t probe_subpage_writeable(const char __user *uaddr,
+					     size_t size)
+{
+	if (!system_supports_mte())
+		return 0;
+	return mte_probe_user_range(uaddr, size);
+}
+
+#endif /* CONFIG_ARCH_HAS_SUBPAGE_FAULTS */
+
 #endif /* __ASM_UACCESS_H */
diff --git a/arch/arm64/include/asm/unistd.h b/arch/arm64/include/asm/unistd.h
index 6bdb5f5db438..037feba03a51 100644
--- a/arch/arm64/include/asm/unistd.h
+++ b/arch/arm64/include/asm/unistd.h
@@ -3,6 +3,7 @@
  * Copyright (C) 2012 ARM Ltd.
  */
 #ifdef CONFIG_COMPAT
+#define __ARCH_WANT_COMPAT_STAT
 #define __ARCH_WANT_COMPAT_STAT64
 #define __ARCH_WANT_SYS_GETHOSTNAME
 #define __ARCH_WANT_SYS_PAUSE
@@ -38,7 +39,7 @@
 #define __ARM_NR_compat_set_tls		(__ARM_NR_COMPAT_BASE + 5)
 #define __ARM_NR_COMPAT_END		(__ARM_NR_COMPAT_BASE + 0x800)
 
-#define __NR_compat_syscalls		450
+#define __NR_compat_syscalls		451
 #endif
 
 #define __ARCH_WANT_SYS_CLONE
diff --git a/arch/arm64/include/asm/unistd32.h b/arch/arm64/include/asm/unistd32.h
index 41ea1195e44b..604a2053d006 100644
--- a/arch/arm64/include/asm/unistd32.h
+++ b/arch/arm64/include/asm/unistd32.h
@@ -905,6 +905,8 @@ __SYSCALL(__NR_landlock_restrict_self, sys_landlock_restrict_self)
 __SYSCALL(__NR_process_mrelease, sys_process_mrelease)
 #define __NR_futex_waitv 449
 __SYSCALL(__NR_futex_waitv, sys_futex_waitv)
+#define __NR_set_mempolicy_home_node 450
+__SYSCALL(__NR_set_mempolicy_home_node, sys_set_mempolicy_home_node)
 
 /*
  * Please add new compat syscalls above this comment and update
diff --git a/arch/arm64/include/asm/vdso.h b/arch/arm64/include/asm/vdso.h
index f99dcb94b438..b4ae32109932 100644
--- a/arch/arm64/include/asm/vdso.h
+++ b/arch/arm64/include/asm/vdso.h
@@ -26,6 +26,9 @@
 	(void *)(vdso_offset_##name - VDSO_LBASE + (unsigned long)(base)); \
 })
 
+extern char vdso_start[], vdso_end[];
+extern char vdso32_start[], vdso32_end[];
+
 #endif /* !__ASSEMBLY__ */
 
 #endif /* __ASM_VDSO_H */
diff --git a/arch/arm64/include/asm/vdso/gettimeofday.h b/arch/arm64/include/asm/vdso/gettimeofday.h
index 4f7a629df81f..764d13e2916c 100644
--- a/arch/arm64/include/asm/vdso/gettimeofday.h
+++ b/arch/arm64/include/asm/vdso/gettimeofday.h
@@ -7,8 +7,10 @@
 
 #ifndef __ASSEMBLY__
 
+#include <asm/alternative.h>
 #include <asm/barrier.h>
 #include <asm/unistd.h>
+#include <asm/sysreg.h>
 
 #define VDSO_HAS_CLOCK_GETRES		1
 
@@ -78,11 +80,20 @@ static __always_inline u64 __arch_get_hw_counter(s32 clock_mode,
 		return 0;
 
 	/*
-	 * This isb() is required to prevent that the counter value
+	 * If FEAT_ECV is available, use the self-synchronizing counter.
+	 * Otherwise the isb is required to prevent that the counter value
 	 * is speculated.
-	 */
-	isb();
-	asm volatile("mrs %0, cntvct_el0" : "=r" (res) :: "memory");
+	*/
+	asm volatile(
+	ALTERNATIVE("isb\n"
+		    "mrs %0, cntvct_el0",
+		    "nop\n"
+		    __mrs_s("%0", SYS_CNTVCTSS_EL0),
+		    ARM64_HAS_ECV)
+	: "=r" (res)
+	:
+	: "memory");
+
 	arch_counter_enforce_ordering(res);
 
 	return res;
diff --git a/arch/arm64/include/asm/vectors.h b/arch/arm64/include/asm/vectors.h
new file mode 100644
index 000000000000..bc9a2145f419
--- /dev/null
+++ b/arch/arm64/include/asm/vectors.h
@@ -0,0 +1,73 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Copyright (C) 2022 ARM Ltd.
+ */
+#ifndef __ASM_VECTORS_H
+#define __ASM_VECTORS_H
+
+#include <linux/bug.h>
+#include <linux/percpu.h>
+
+#include <asm/fixmap.h>
+
+extern char vectors[];
+extern char tramp_vectors[];
+extern char __bp_harden_el1_vectors[];
+
+/*
+ * Note: the order of this enum corresponds to two arrays in entry.S:
+ * tramp_vecs and __bp_harden_el1_vectors. By default the canonical
+ * 'full fat' vectors are used directly.
+ */
+enum arm64_bp_harden_el1_vectors {
+#ifdef CONFIG_MITIGATE_SPECTRE_BRANCH_HISTORY
+	/*
+	 * Perform the BHB loop mitigation, before branching to the canonical
+	 * vectors.
+	 */
+	EL1_VECTOR_BHB_LOOP,
+
+	/*
+	 * Make the SMC call for firmware mitigation, before branching to the
+	 * canonical vectors.
+	 */
+	EL1_VECTOR_BHB_FW,
+
+	/*
+	 * Use the ClearBHB instruction, before branching to the canonical
+	 * vectors.
+	 */
+	EL1_VECTOR_BHB_CLEAR_INSN,
+#endif /* CONFIG_MITIGATE_SPECTRE_BRANCH_HISTORY */
+
+	/*
+	 * Remap the kernel before branching to the canonical vectors.
+	 */
+	EL1_VECTOR_KPTI,
+};
+
+#ifndef CONFIG_MITIGATE_SPECTRE_BRANCH_HISTORY
+#define EL1_VECTOR_BHB_LOOP		-1
+#define EL1_VECTOR_BHB_FW		-1
+#define EL1_VECTOR_BHB_CLEAR_INSN	-1
+#endif /* !CONFIG_MITIGATE_SPECTRE_BRANCH_HISTORY */
+
+/* The vectors to use on return from EL0. e.g. to remap the kernel */
+DECLARE_PER_CPU_READ_MOSTLY(const char *, this_cpu_vector);
+
+#ifndef CONFIG_UNMAP_KERNEL_AT_EL0
+#define TRAMP_VALIAS	0ul
+#endif
+
+static inline const char *
+arm64_get_bp_hardening_vector(enum arm64_bp_harden_el1_vectors slot)
+{
+	if (arm64_kernel_unmapped_at_el0())
+		return (char *)(TRAMP_VALIAS + SZ_2K * slot);
+
+	WARN_ON_ONCE(slot == EL1_VECTOR_KPTI);
+
+	return __bp_harden_el1_vectors + SZ_2K * slot;
+}
+
+#endif /* __ASM_VECTORS_H */
diff --git a/arch/arm64/include/asm/virt.h b/arch/arm64/include/asm/virt.h
index 3c8af033a997..4eb601e7de50 100644
--- a/arch/arm64/include/asm/virt.h
+++ b/arch/arm64/include/asm/virt.h
@@ -36,9 +36,9 @@
 #define HVC_RESET_VECTORS 2
 
 /*
- * HVC_VHE_RESTART - Upgrade the CPU from EL1 to EL2, if possible
+ * HVC_FINALISE_EL2 - Upgrade the CPU from EL1 to EL2, if possible
  */
-#define HVC_VHE_RESTART	3
+#define HVC_FINALISE_EL2	3
 
 /* Max number of HYP stub hypercalls */
 #define HVC_STUB_HCALL_NR 4
@@ -49,6 +49,13 @@
 #define BOOT_CPU_MODE_EL1	(0xe11)
 #define BOOT_CPU_MODE_EL2	(0xe12)
 
+/*
+ * Flags returned together with the boot mode, but not preserved in
+ * __boot_cpu_mode. Used by the idreg override code to work out the
+ * boot state.
+ */
+#define BOOT_CPU_FLAG_E2H	BIT_ULL(32)
+
 #ifndef __ASSEMBLY__
 
 #include <asm/ptrace.h>
@@ -113,6 +120,9 @@ static __always_inline bool has_vhe(void)
 	/*
 	 * Code only run in VHE/NVHE hyp context can assume VHE is present or
 	 * absent. Otherwise fall back to caps.
+	 * This allows the compiler to discard VHE-specific code from the
+	 * nVHE object, reducing the number of external symbol references
+	 * needed to link.
 	 */
 	if (is_vhe_hyp_code())
 		return true;
diff --git a/arch/arm64/include/asm/vmalloc.h b/arch/arm64/include/asm/vmalloc.h
index b9185503feae..38fafffe699f 100644
--- a/arch/arm64/include/asm/vmalloc.h
+++ b/arch/arm64/include/asm/vmalloc.h
@@ -25,4 +25,10 @@ static inline bool arch_vmap_pmd_supported(pgprot_t prot)
 
 #endif
 
+#define arch_vmap_pgprot_tagged arch_vmap_pgprot_tagged
+static inline pgprot_t arch_vmap_pgprot_tagged(pgprot_t prot)
+{
+	return pgprot_tagged(prot);
+}
+
 #endif /* _ASM_ARM64_VMALLOC_H */
diff --git a/arch/arm64/include/asm/vmap_stack.h b/arch/arm64/include/asm/vmap_stack.h
index 894e031b28d2..20873099c035 100644
--- a/arch/arm64/include/asm/vmap_stack.h
+++ b/arch/arm64/include/asm/vmap_stack.h
@@ -17,10 +17,13 @@
  */
 static inline unsigned long *arch_alloc_vmap_stack(size_t stack_size, int node)
 {
+	void *p;
+
 	BUILD_BUG_ON(!IS_ENABLED(CONFIG_VMAP_STACK));
 
-	return __vmalloc_node(stack_size, THREAD_ALIGN, THREADINFO_GFP, node,
+	p = __vmalloc_node(stack_size, THREAD_ALIGN, THREADINFO_GFP, node,
 			__builtin_return_address(0));
+	return kasan_reset_tag(p);
 }
 
 #endif /* __ASM_VMAP_STACK_H */
diff --git a/arch/arm64/include/asm/xen/page-coherent.h b/arch/arm64/include/asm/xen/page-coherent.h
deleted file mode 100644
index 27e984977402..000000000000
--- a/arch/arm64/include/asm/xen/page-coherent.h
+++ /dev/null
@@ -1,2 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-#include <xen/arm/page-coherent.h>
diff --git a/arch/arm64/include/asm/xen/xen-ops.h b/arch/arm64/include/asm/xen/xen-ops.h
new file mode 100644
index 000000000000..7ebb7eb0bd93
--- /dev/null
+++ b/arch/arm64/include/asm/xen/xen-ops.h
@@ -0,0 +1,2 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#include <xen/arm/xen-ops.h>
diff --git a/arch/arm64/include/asm/xor.h b/arch/arm64/include/asm/xor.h
index 947f6a4f1aa0..befcd8a7abc9 100644
--- a/arch/arm64/include/asm/xor.h
+++ b/arch/arm64/include/asm/xor.h
@@ -16,7 +16,8 @@
 extern struct xor_block_template const xor_block_inner_neon;
 
 static void
-xor_neon_2(unsigned long bytes, unsigned long *p1, unsigned long *p2)
+xor_neon_2(unsigned long bytes, unsigned long * __restrict p1,
+	   const unsigned long * __restrict p2)
 {
 	kernel_neon_begin();
 	xor_block_inner_neon.do_2(bytes, p1, p2);
@@ -24,8 +25,9 @@ xor_neon_2(unsigned long bytes, unsigned long *p1, unsigned long *p2)
 }
 
 static void
-xor_neon_3(unsigned long bytes, unsigned long *p1, unsigned long *p2,
-		unsigned long *p3)
+xor_neon_3(unsigned long bytes, unsigned long * __restrict p1,
+	   const unsigned long * __restrict p2,
+	   const unsigned long * __restrict p3)
 {
 	kernel_neon_begin();
 	xor_block_inner_neon.do_3(bytes, p1, p2, p3);
@@ -33,8 +35,10 @@ xor_neon_3(unsigned long bytes, unsigned long *p1, unsigned long *p2,
 }
 
 static void
-xor_neon_4(unsigned long bytes, unsigned long *p1, unsigned long *p2,
-		unsigned long *p3, unsigned long *p4)
+xor_neon_4(unsigned long bytes, unsigned long * __restrict p1,
+	   const unsigned long * __restrict p2,
+	   const unsigned long * __restrict p3,
+	   const unsigned long * __restrict p4)
 {
 	kernel_neon_begin();
 	xor_block_inner_neon.do_4(bytes, p1, p2, p3, p4);
@@ -42,8 +46,11 @@ xor_neon_4(unsigned long bytes, unsigned long *p1, unsigned long *p2,
 }
 
 static void
-xor_neon_5(unsigned long bytes, unsigned long *p1, unsigned long *p2,
-		unsigned long *p3, unsigned long *p4, unsigned long *p5)
+xor_neon_5(unsigned long bytes, unsigned long * __restrict p1,
+	   const unsigned long * __restrict p2,
+	   const unsigned long * __restrict p3,
+	   const unsigned long * __restrict p4,
+	   const unsigned long * __restrict p5)
 {
 	kernel_neon_begin();
 	xor_block_inner_neon.do_5(bytes, p1, p2, p3, p4, p5);
diff --git a/arch/arm64/include/uapi/asm/hwcap.h b/arch/arm64/include/uapi/asm/hwcap.h
index 7b23b16f21ce..9b245da6f507 100644
--- a/arch/arm64/include/uapi/asm/hwcap.h
+++ b/arch/arm64/include/uapi/asm/hwcap.h
@@ -19,6 +19,9 @@
 
 /*
  * HWCAP flags - for AT_HWCAP
+ *
+ * Bits 62 and 63 are reserved for use by libc.
+ * Bits 32-61 are unallocated for potential use by libc.
  */
 #define HWCAP_FP		(1 << 0)
 #define HWCAP_ASIMD		(1 << 1)
@@ -76,5 +79,19 @@
 #define HWCAP2_BTI		(1 << 17)
 #define HWCAP2_MTE		(1 << 18)
 #define HWCAP2_ECV		(1 << 19)
+#define HWCAP2_AFP		(1 << 20)
+#define HWCAP2_RPRES		(1 << 21)
+#define HWCAP2_MTE3		(1 << 22)
+#define HWCAP2_SME		(1 << 23)
+#define HWCAP2_SME_I16I64	(1 << 24)
+#define HWCAP2_SME_F64F64	(1 << 25)
+#define HWCAP2_SME_I8I32	(1 << 26)
+#define HWCAP2_SME_F16F32	(1 << 27)
+#define HWCAP2_SME_B16F32	(1 << 28)
+#define HWCAP2_SME_F32F32	(1 << 29)
+#define HWCAP2_SME_FA64		(1 << 30)
+#define HWCAP2_WFXT		(1UL << 31)
+#define HWCAP2_EBF16		(1UL << 32)
+#define HWCAP2_SVE_EBF16	(1UL << 33)
 
 #endif /* _UAPI__ASM_HWCAP_H */
diff --git a/arch/arm64/include/uapi/asm/kvm.h b/arch/arm64/include/uapi/asm/kvm.h
index b3edde68bc3e..316917b98707 100644
--- a/arch/arm64/include/uapi/asm/kvm.h
+++ b/arch/arm64/include/uapi/asm/kvm.h
@@ -75,9 +75,11 @@ struct kvm_regs {
 
 /* KVM_ARM_SET_DEVICE_ADDR ioctl id encoding */
 #define KVM_ARM_DEVICE_TYPE_SHIFT	0
-#define KVM_ARM_DEVICE_TYPE_MASK	(0xffff << KVM_ARM_DEVICE_TYPE_SHIFT)
+#define KVM_ARM_DEVICE_TYPE_MASK	GENMASK(KVM_ARM_DEVICE_TYPE_SHIFT + 15, \
+						KVM_ARM_DEVICE_TYPE_SHIFT)
 #define KVM_ARM_DEVICE_ID_SHIFT		16
-#define KVM_ARM_DEVICE_ID_MASK		(0xffff << KVM_ARM_DEVICE_ID_SHIFT)
+#define KVM_ARM_DEVICE_ID_MASK		GENMASK(KVM_ARM_DEVICE_ID_SHIFT + 15, \
+						KVM_ARM_DEVICE_ID_SHIFT)
 
 /* Supported device IDs */
 #define KVM_ARM_DEVICE_VGIC_V2		0
@@ -139,8 +141,10 @@ struct kvm_guest_debug_arch {
 	__u64 dbg_wvr[KVM_ARM_MAX_DBG_REGS];
 };
 
+#define KVM_DEBUG_ARCH_HSR_HIGH_VALID	(1 << 0)
 struct kvm_debug_exit_arch {
 	__u32 hsr;
+	__u32 hsr_high;	/* ESR_EL2[61:32] */
 	__u64 far;	/* used for watchpoints */
 };
 
@@ -281,6 +285,11 @@ struct kvm_arm_copy_mte_tags {
 #define KVM_REG_ARM_SMCCC_ARCH_WORKAROUND_2_NOT_REQUIRED	3
 #define KVM_REG_ARM_SMCCC_ARCH_WORKAROUND_2_ENABLED     	(1U << 4)
 
+#define KVM_REG_ARM_SMCCC_ARCH_WORKAROUND_3	KVM_REG_ARM_FW_REG(3)
+#define KVM_REG_ARM_SMCCC_ARCH_WORKAROUND_3_NOT_AVAIL		0
+#define KVM_REG_ARM_SMCCC_ARCH_WORKAROUND_3_AVAIL		1
+#define KVM_REG_ARM_SMCCC_ARCH_WORKAROUND_3_NOT_REQUIRED	2
+
 /* SVE registers */
 #define KVM_REG_ARM64_SVE		(0x15 << KVM_REG_ARM_COPROC_SHIFT)
 
@@ -327,6 +336,40 @@ struct kvm_arm_copy_mte_tags {
 #define KVM_ARM64_SVE_VLS_WORDS	\
 	((KVM_ARM64_SVE_VQ_MAX - KVM_ARM64_SVE_VQ_MIN) / 64 + 1)
 
+/* Bitmap feature firmware registers */
+#define KVM_REG_ARM_FW_FEAT_BMAP		(0x0016 << KVM_REG_ARM_COPROC_SHIFT)
+#define KVM_REG_ARM_FW_FEAT_BMAP_REG(r)		(KVM_REG_ARM64 | KVM_REG_SIZE_U64 | \
+						KVM_REG_ARM_FW_FEAT_BMAP |	\
+						((r) & 0xffff))
+
+#define KVM_REG_ARM_STD_BMAP			KVM_REG_ARM_FW_FEAT_BMAP_REG(0)
+
+enum {
+	KVM_REG_ARM_STD_BIT_TRNG_V1_0	= 0,
+#ifdef __KERNEL__
+	KVM_REG_ARM_STD_BMAP_BIT_COUNT,
+#endif
+};
+
+#define KVM_REG_ARM_STD_HYP_BMAP		KVM_REG_ARM_FW_FEAT_BMAP_REG(1)
+
+enum {
+	KVM_REG_ARM_STD_HYP_BIT_PV_TIME	= 0,
+#ifdef __KERNEL__
+	KVM_REG_ARM_STD_HYP_BMAP_BIT_COUNT,
+#endif
+};
+
+#define KVM_REG_ARM_VENDOR_HYP_BMAP		KVM_REG_ARM_FW_FEAT_BMAP_REG(2)
+
+enum {
+	KVM_REG_ARM_VENDOR_HYP_BIT_FUNC_FEAT	= 0,
+	KVM_REG_ARM_VENDOR_HYP_BIT_PTP		= 1,
+#ifdef __KERNEL__
+	KVM_REG_ARM_VENDOR_HYP_BMAP_BIT_COUNT,
+#endif
+};
+
 /* Device Control API: ARM VGIC */
 #define KVM_DEV_ARM_VGIC_GRP_ADDR	0
 #define KVM_DEV_ARM_VGIC_GRP_DIST_REGS	1
@@ -362,6 +405,7 @@ struct kvm_arm_copy_mte_tags {
 #define   KVM_ARM_VCPU_PMU_V3_IRQ	0
 #define   KVM_ARM_VCPU_PMU_V3_INIT	1
 #define   KVM_ARM_VCPU_PMU_V3_FILTER	2
+#define   KVM_ARM_VCPU_PMU_V3_SET_PMU	3
 #define KVM_ARM_VCPU_TIMER_CTRL		1
 #define   KVM_ARM_VCPU_TIMER_IRQ_VTIMER		0
 #define   KVM_ARM_VCPU_TIMER_IRQ_PTIMER		1
@@ -413,6 +457,16 @@ struct kvm_arm_copy_mte_tags {
 #define KVM_PSCI_RET_INVAL		PSCI_RET_INVALID_PARAMS
 #define KVM_PSCI_RET_DENIED		PSCI_RET_DENIED
 
+/* arm64-specific kvm_run::system_event flags */
+/*
+ * Reset caused by a PSCI v1.1 SYSTEM_RESET2 call.
+ * Valid only when the system event has a type of KVM_SYSTEM_EVENT_RESET.
+ */
+#define KVM_SYSTEM_EVENT_RESET_FLAG_PSCI_RESET2	(1ULL << 0)
+
+/* run->fail_entry.hardware_entry_failure_reason codes. */
+#define KVM_EXIT_FAIL_ENTRY_CPU_UNSUPPORTED	(1ULL << 0)
+
 #endif
 
 #endif /* __ARM_KVM_H__ */
diff --git a/arch/arm64/include/uapi/asm/perf_regs.h b/arch/arm64/include/uapi/asm/perf_regs.h
index d54daafa89e3..86e556429e0e 100644
--- a/arch/arm64/include/uapi/asm/perf_regs.h
+++ b/arch/arm64/include/uapi/asm/perf_regs.h
@@ -37,5 +37,12 @@ enum perf_event_arm_regs {
 	PERF_REG_ARM64_SP,
 	PERF_REG_ARM64_PC,
 	PERF_REG_ARM64_MAX,
+
+	/* Extended/pseudo registers */
+	PERF_REG_ARM64_VG = 46,				/* SVE Vector Granule */
+	PERF_REG_ARM64_EXTENDED_MAX
 };
+
+#define PERF_REG_EXTENDED_MASK	(1ULL << PERF_REG_ARM64_VG)
+
 #endif /* _ASM_ARM64_PERF_REGS_H */
diff --git a/arch/arm64/include/uapi/asm/ptrace.h b/arch/arm64/include/uapi/asm/ptrace.h
index 758ae984ff97..7fa2f7036aa7 100644
--- a/arch/arm64/include/uapi/asm/ptrace.h
+++ b/arch/arm64/include/uapi/asm/ptrace.h
@@ -109,7 +109,7 @@ struct user_hwdebug_state {
 	}		dbg_regs[16];
 };
 
-/* SVE/FP/SIMD state (NT_ARM_SVE) */
+/* SVE/FP/SIMD state (NT_ARM_SVE & NT_ARM_SSVE) */
 
 struct user_sve_header {
 	__u32 size; /* total meaningful regset content in bytes */
@@ -220,6 +220,7 @@ struct user_sve_header {
 	(SVE_PT_SVE_PREG_OFFSET(vq, __SVE_NUM_PREGS) - \
 		SVE_PT_SVE_PREGS_OFFSET(vq))
 
+/* For streaming mode SVE (SSVE) FFR must be read and written as zero */
 #define SVE_PT_SVE_FFR_OFFSET(vq) \
 	(SVE_PT_REGS_OFFSET + __SVE_FFR_OFFSET(vq))
 
@@ -240,10 +241,12 @@ struct user_sve_header {
 			- SVE_PT_SVE_OFFSET + (__SVE_VQ_BYTES - 1))	\
 		/ __SVE_VQ_BYTES * __SVE_VQ_BYTES)
 
-#define SVE_PT_SIZE(vq, flags)						\
-	 (((flags) & SVE_PT_REGS_MASK) == SVE_PT_REGS_SVE ?		\
-		  SVE_PT_SVE_OFFSET + SVE_PT_SVE_SIZE(vq, flags)	\
-		: SVE_PT_FPSIMD_OFFSET + SVE_PT_FPSIMD_SIZE(vq, flags))
+#define SVE_PT_SIZE(vq, flags)						  \
+	 (((flags) & SVE_PT_REGS_MASK) == SVE_PT_REGS_SVE ?		  \
+		  SVE_PT_SVE_OFFSET + SVE_PT_SVE_SIZE(vq, flags)	  \
+		: ((((flags) & SVE_PT_REGS_MASK) == SVE_PT_REGS_FPSIMD ?  \
+		    SVE_PT_FPSIMD_OFFSET + SVE_PT_FPSIMD_SIZE(vq, flags) \
+		  : SVE_PT_REGS_OFFSET)))
 
 /* pointer authentication masks (NT_ARM_PAC_MASK) */
 
@@ -265,6 +268,62 @@ struct user_pac_generic_keys {
 	__uint128_t	apgakey;
 };
 
+/* ZA state (NT_ARM_ZA) */
+
+struct user_za_header {
+	__u32 size; /* total meaningful regset content in bytes */
+	__u32 max_size; /* maxmium possible size for this thread */
+	__u16 vl; /* current vector length */
+	__u16 max_vl; /* maximum possible vector length */
+	__u16 flags;
+	__u16 __reserved;
+};
+
+/*
+ * Common ZA_PT_* flags:
+ * These must be kept in sync with prctl interface in <linux/prctl.h>
+ */
+#define ZA_PT_VL_INHERIT		((1 << 17) /* PR_SME_VL_INHERIT */ >> 16)
+#define ZA_PT_VL_ONEXEC			((1 << 18) /* PR_SME_SET_VL_ONEXEC */ >> 16)
+
+
+/*
+ * The remainder of the ZA state follows struct user_za_header.  The
+ * total size of the ZA state (including header) depends on the
+ * metadata in the header:  ZA_PT_SIZE(vq, flags) gives the total size
+ * of the state in bytes, including the header.
+ *
+ * Refer to <asm/sigcontext.h> for details of how to pass the correct
+ * "vq" argument to these macros.
+ */
+
+/* Offset from the start of struct user_za_header to the register data */
+#define ZA_PT_ZA_OFFSET						\
+	((sizeof(struct user_za_header) + (__SVE_VQ_BYTES - 1))	\
+		/ __SVE_VQ_BYTES * __SVE_VQ_BYTES)
+
+/*
+ * The payload starts at offset ZA_PT_ZA_OFFSET, and is of size
+ * ZA_PT_ZA_SIZE(vq, flags).
+ *
+ * The ZA array is stored as a sequence of horizontal vectors ZAV of SVL/8
+ * bytes each, starting from vector 0.
+ *
+ * Additional data might be appended in the future.
+ *
+ * The ZA matrix is represented in memory in an endianness-invariant layout
+ * which differs from the layout used for the FPSIMD V-registers on big-endian
+ * systems: see sigcontext.h for more explanation.
+ */
+
+#define ZA_PT_ZAV_OFFSET(vq, n) \
+	(ZA_PT_ZA_OFFSET + ((vq * __SVE_VQ_BYTES) * n))
+
+#define ZA_PT_ZA_SIZE(vq) ((vq * __SVE_VQ_BYTES) * (vq * __SVE_VQ_BYTES))
+
+#define ZA_PT_SIZE(vq)						\
+	(ZA_PT_ZA_OFFSET + ZA_PT_ZA_SIZE(vq))
+
 #endif /* __ASSEMBLY__ */
 
 #endif /* _UAPI__ASM_PTRACE_H */
diff --git a/arch/arm64/include/uapi/asm/sigcontext.h b/arch/arm64/include/uapi/asm/sigcontext.h
index 0c796c795dbe..4aaf31e3bf16 100644
--- a/arch/arm64/include/uapi/asm/sigcontext.h
+++ b/arch/arm64/include/uapi/asm/sigcontext.h
@@ -134,6 +134,17 @@ struct extra_context {
 struct sve_context {
 	struct _aarch64_ctx head;
 	__u16 vl;
+	__u16 flags;
+	__u16 __reserved[2];
+};
+
+#define SVE_SIG_FLAG_SM	0x1	/* Context describes streaming mode */
+
+#define ZA_MAGIC	0x54366345
+
+struct za_context {
+	struct _aarch64_ctx head;
+	__u16 vl;
 	__u16 __reserved[3];
 };
 
@@ -186,9 +197,16 @@ struct sve_context {
  * sve_context.vl must equal the thread's current vector length when
  * doing a sigreturn.
  *
+ * On systems with support for SME the SVE register state may reflect either
+ * streaming or non-streaming mode.  In streaming mode the streaming mode
+ * vector length will be used and the flag SVE_SIG_FLAG_SM will be set in
+ * the flags field. It is permitted to enter or leave streaming mode in
+ * a signal return, applications should take care to ensure that any difference
+ * in vector length between the two modes is handled, including any resizing
+ * and movement of context blocks.
  *
- * Note: for all these macros, the "vq" argument denotes the SVE
- * vector length in quadwords (i.e., units of 128 bits).
+ * Note: for all these macros, the "vq" argument denotes the vector length
+ * in quadwords (i.e., units of 128 bits).
  *
  * The correct way to obtain vq is to use sve_vq_from_vl(vl).  The
  * result is valid if and only if sve_vl_valid(vl) is true.  This is
@@ -249,4 +267,37 @@ struct sve_context {
 #define SVE_SIG_CONTEXT_SIZE(vq) \
 		(SVE_SIG_REGS_OFFSET + SVE_SIG_REGS_SIZE(vq))
 
+/*
+ * If the ZA register is enabled for the thread at signal delivery then,
+ * za_context.head.size >= ZA_SIG_CONTEXT_SIZE(sve_vq_from_vl(za_context.vl))
+ * and the register data may be accessed using the ZA_SIG_*() macros.
+ *
+ * If za_context.head.size < ZA_SIG_CONTEXT_SIZE(sve_vq_from_vl(za_context.vl))
+ * then ZA was not enabled and no register data was included in which case
+ * ZA register was not enabled for the thread and no register data
+ * the ZA_SIG_*() macros should not be used except for this check.
+ *
+ * The same convention applies when returning from a signal: a caller
+ * will need to remove or resize the za_context block if it wants to
+ * enable the ZA register when it was previously non-live or vice-versa.
+ * This may require the caller to allocate fresh memory and/or move other
+ * context blocks in the signal frame.
+ *
+ * Changing the vector length during signal return is not permitted:
+ * za_context.vl must equal the thread's current SME vector length when
+ * doing a sigreturn.
+ */
+
+#define ZA_SIG_REGS_OFFSET					\
+	((sizeof(struct za_context) + (__SVE_VQ_BYTES - 1))	\
+		/ __SVE_VQ_BYTES * __SVE_VQ_BYTES)
+
+#define ZA_SIG_REGS_SIZE(vq) ((vq * __SVE_VQ_BYTES) * (vq * __SVE_VQ_BYTES))
+
+#define ZA_SIG_ZAV_OFFSET(vq, n) (ZA_SIG_REGS_OFFSET + \
+				  (SVE_SIG_ZREG_SIZE(vq) * n))
+
+#define ZA_SIG_CONTEXT_SIZE(vq) \
+		(ZA_SIG_REGS_OFFSET + ZA_SIG_REGS_SIZE(vq))
+
 #endif /* _UAPI__ASM_SIGCONTEXT_H */
diff --git a/arch/arm64/kernel/Makefile b/arch/arm64/kernel/Makefile
index 88b3e2a21408..2f361a883d8c 100644
--- a/arch/arm64/kernel/Makefile
+++ b/arch/arm64/kernel/Makefile
@@ -14,6 +14,11 @@ CFLAGS_REMOVE_return_address.o = $(CC_FLAGS_FTRACE)
 CFLAGS_REMOVE_syscall.o	 = -fstack-protector -fstack-protector-strong
 CFLAGS_syscall.o	+= -fno-stack-protector
 
+# When KASAN is enabled, a stack trace is recorded for every alloc/free, which
+# can significantly impact performance. Avoid instrumenting the stack trace
+# collection code to minimize this impact.
+KASAN_SANITIZE_stacktrace.o := n
+
 # It's not safe to invoke KCOV when portions of the kernel environment aren't
 # available or are out-of-sync with HW state. Since `noinstr` doesn't always
 # inhibit KCOV instrumentation, disable it for the entire compilation unit.
@@ -40,6 +45,7 @@ $(obj)/%.stub.o: $(obj)/%.o FORCE
 obj-$(CONFIG_COMPAT)			+= sys32.o signal32.o			\
 					   sys_compat.o
 obj-$(CONFIG_COMPAT)			+= sigreturn32.o
+obj-$(CONFIG_COMPAT_ALIGNMENT_FIXUPS)	+= compat_alignment.o
 obj-$(CONFIG_KUSER_HELPERS)		+= kuser32.o
 obj-$(CONFIG_FUNCTION_TRACER)		+= ftrace.o entry-ftrace.o
 obj-$(CONFIG_MODULES)			+= module.o
@@ -59,8 +65,9 @@ obj-$(CONFIG_ACPI)			+= acpi.o
 obj-$(CONFIG_ACPI_NUMA)			+= acpi_numa.o
 obj-$(CONFIG_ARM64_ACPI_PARKING_PROTOCOL)	+= acpi_parking_protocol.o
 obj-$(CONFIG_PARAVIRT)			+= paravirt.o
-obj-$(CONFIG_RANDOMIZE_BASE)		+= kaslr.o
+obj-$(CONFIG_RANDOMIZE_BASE)		+= kaslr.o pi/
 obj-$(CONFIG_HIBERNATION)		+= hibernate.o hibernate-asm.o
+obj-$(CONFIG_ELF_CORE)			+= elfcore.o
 obj-$(CONFIG_KEXEC_CORE)		+= machine_kexec.o relocate_kernel.o	\
 					   cpu-reset.o
 obj-$(CONFIG_KEXEC_FILE)		+= machine_kexec_file.o kexec_image.o
@@ -74,9 +81,13 @@ obj-$(CONFIG_ARM64_MTE)			+= mte.o
 obj-y					+= vdso-wrap.o
 obj-$(CONFIG_COMPAT_VDSO)		+= vdso32-wrap.o
 
+# Force dependency (vdso*-wrap.S includes vdso.so through incbin)
+$(obj)/vdso-wrap.o: $(obj)/vdso/vdso.so
+$(obj)/vdso32-wrap.o: $(obj)/vdso32/vdso.so
+
 obj-y					+= probes/
-head-y					:= head.o
-extra-y					+= $(head-y) vmlinux.lds
+obj-y					+= head.o
+extra-y					+= vmlinux.lds
 
 ifeq ($(CONFIG_DEBUG_EFI),y)
 AFLAGS_head.o += -DVMLINUX_PATH="\"$(realpath $(objtree)/vmlinux)\""
diff --git a/arch/arm64/kernel/acpi.c b/arch/arm64/kernel/acpi.c
index f3851724fe35..a5a256e3f9fe 100644
--- a/arch/arm64/kernel/acpi.c
+++ b/arch/arm64/kernel/acpi.c
@@ -22,6 +22,7 @@
 #include <linux/irq_work.h>
 #include <linux/memblock.h>
 #include <linux/of_fdt.h>
+#include <linux/libfdt.h>
 #include <linux/smp.h>
 #include <linux/serial_core.h>
 #include <linux/pgtable.h>
@@ -62,29 +63,22 @@ static int __init parse_acpi(char *arg)
 }
 early_param("acpi", parse_acpi);
 
-static int __init dt_scan_depth1_nodes(unsigned long node,
-				       const char *uname, int depth,
-				       void *data)
+static bool __init dt_is_stub(void)
 {
-	/*
-	 * Ignore anything not directly under the root node; we'll
-	 * catch its parent instead.
-	 */
-	if (depth != 1)
-		return 0;
+	int node;
 
-	if (strcmp(uname, "chosen") == 0)
-		return 0;
+	fdt_for_each_subnode(node, initial_boot_params, 0) {
+		const char *name = fdt_get_name(initial_boot_params, node, NULL);
+		if (strcmp(name, "chosen") == 0)
+			continue;
+		if (strcmp(name, "hypervisor") == 0 &&
+		    of_flat_dt_is_compatible(node, "xen,xen"))
+			continue;
 
-	if (strcmp(uname, "hypervisor") == 0 &&
-	    of_flat_dt_is_compatible(node, "xen,xen"))
-		return 0;
+		return false;
+	}
 
-	/*
-	 * This node at depth 1 is neither a chosen node nor a xen node,
-	 * which we do not expect.
-	 */
-	return 1;
+	return true;
 }
 
 /*
@@ -205,8 +199,7 @@ void __init acpi_boot_table_init(void)
 	 *   and ACPI has not been [force] enabled (acpi=on|force)
 	 */
 	if (param_acpi_off ||
-	    (!param_acpi_on && !param_acpi_force &&
-	     of_scan_flat_dt(dt_scan_depth1_nodes, NULL)))
+	    (!param_acpi_on && !param_acpi_force && !dt_is_stub()))
 		goto done;
 
 	/*
@@ -358,7 +351,7 @@ void __iomem *acpi_os_ioremap(acpi_physical_address phys, acpi_size size)
 				prot = __acpi_get_writethrough_mem_attribute();
 		}
 	}
-	return __ioremap(phys, size, prot);
+	return ioremap_prot(phys, size, pgprot_val(prot));
 }
 
 /*
diff --git a/arch/arm64/kernel/acpi_numa.c b/arch/arm64/kernel/acpi_numa.c
index fdfecf0991ce..e51535a5f939 100644
--- a/arch/arm64/kernel/acpi_numa.c
+++ b/arch/arm64/kernel/acpi_numa.c
@@ -109,7 +109,7 @@ void __init acpi_numa_gicc_affinity_init(struct acpi_srat_gicc_affinity *pa)
 	pxm = pa->proximity_domain;
 	node = acpi_map_pxm_to_node(pxm);
 
-	if (node == NUMA_NO_NODE || node >= MAX_NUMNODES) {
+	if (node == NUMA_NO_NODE) {
 		pr_err("SRAT: Too many proximity domains %d\n", pxm);
 		bad_srat();
 		return;
diff --git a/arch/arm64/kernel/acpi_parking_protocol.c b/arch/arm64/kernel/acpi_parking_protocol.c
index bfeeb5319abf..b1990e38aed0 100644
--- a/arch/arm64/kernel/acpi_parking_protocol.c
+++ b/arch/arm64/kernel/acpi_parking_protocol.c
@@ -99,7 +99,7 @@ static int acpi_parking_protocol_cpu_boot(unsigned int cpu)
 	 * that read this address need to convert this address to the
 	 * Boot-Loader's endianness before jumping.
 	 */
-	writeq_relaxed(__pa_symbol(function_nocfi(secondary_entry)),
+	writeq_relaxed(__pa_symbol(secondary_entry),
 		       &mailbox->entry_point);
 	writel_relaxed(cpu_entry->gic_cpu_id, &mailbox->cpu_id);
 
diff --git a/arch/arm64/kernel/alternative.c b/arch/arm64/kernel/alternative.c
index 3fb79b76e9d9..91263d09ea65 100644
--- a/arch/arm64/kernel/alternative.c
+++ b/arch/arm64/kernel/alternative.c
@@ -10,17 +10,23 @@
 
 #include <linux/init.h>
 #include <linux/cpu.h>
+#include <linux/elf.h>
 #include <asm/cacheflush.h>
 #include <asm/alternative.h>
 #include <asm/cpufeature.h>
 #include <asm/insn.h>
+#include <asm/module.h>
 #include <asm/sections.h>
+#include <asm/vdso.h>
 #include <linux/stop_machine.h>
 
 #define __ALT_PTR(a, f)		((void *)&(a)->f + (a)->f)
 #define ALT_ORIG_PTR(a)		__ALT_PTR(a, orig_offset)
 #define ALT_REPL_PTR(a)		__ALT_PTR(a, alt_offset)
 
+#define ALT_CAP(a)		((a)->cpufeature & ~ARM64_CB_BIT)
+#define ALT_HAS_CB(a)		((a)->cpufeature & ARM64_CB_BIT)
+
 /* Volatile, as we may be patching the guts of READ_ONCE() */
 static volatile int all_alternatives_applied;
 
@@ -42,7 +48,7 @@ bool alternative_is_applied(u16 cpufeature)
 /*
  * Check if the target PC is within an alternative block.
  */
-static bool branch_insn_requires_update(struct alt_instr *alt, unsigned long pc)
+static __always_inline bool branch_insn_requires_update(struct alt_instr *alt, unsigned long pc)
 {
 	unsigned long replptr = (unsigned long)ALT_REPL_PTR(alt);
 	return !(pc >= replptr && pc <= (replptr + alt->alt_len));
@@ -50,7 +56,7 @@ static bool branch_insn_requires_update(struct alt_instr *alt, unsigned long pc)
 
 #define align_down(x, a)	((unsigned long)(x) & ~(((unsigned long)(a)) - 1))
 
-static u32 get_alt_insn(struct alt_instr *alt, __le32 *insnptr, __le32 *altinsnptr)
+static __always_inline u32 get_alt_insn(struct alt_instr *alt, __le32 *insnptr, __le32 *altinsnptr)
 {
 	u32 insn;
 
@@ -95,7 +101,7 @@ static u32 get_alt_insn(struct alt_instr *alt, __le32 *insnptr, __le32 *altinsnp
 	return insn;
 }
 
-static void patch_alternative(struct alt_instr *alt,
+static noinstr void patch_alternative(struct alt_instr *alt,
 			      __le32 *origptr, __le32 *updptr, int nr_inst)
 {
 	__le32 *replptr;
@@ -121,7 +127,7 @@ static void clean_dcache_range_nopatch(u64 start, u64 end)
 
 	ctr_el0 = read_sanitised_ftr_reg(SYS_CTR_EL0);
 	d_size = 4 << cpuid_feature_extract_unsigned_field(ctr_el0,
-							   CTR_DMINLINE_SHIFT);
+							   CTR_EL0_DminLine_SHIFT);
 	cur = start & ~(d_size - 1);
 	do {
 		/*
@@ -133,7 +139,8 @@ static void clean_dcache_range_nopatch(u64 start, u64 end)
 	} while (cur += d_size, cur < end);
 }
 
-static void __nocfi __apply_alternatives(struct alt_region *region, bool is_module,
+static void __apply_alternatives(const struct alt_region *region,
+				 bool is_module,
 				 unsigned long *feature_mask)
 {
 	struct alt_instr *alt;
@@ -142,30 +149,27 @@ static void __nocfi __apply_alternatives(struct alt_region *region, bool is_modu
 
 	for (alt = region->begin; alt < region->end; alt++) {
 		int nr_inst;
+		int cap = ALT_CAP(alt);
 
-		if (!test_bit(alt->cpufeature, feature_mask))
+		if (!test_bit(cap, feature_mask))
 			continue;
 
-		/* Use ARM64_CB_PATCH as an unconditional patch */
-		if (alt->cpufeature < ARM64_CB_PATCH &&
-		    !cpus_have_cap(alt->cpufeature))
+		if (!cpus_have_cap(cap))
 			continue;
 
-		if (alt->cpufeature == ARM64_CB_PATCH)
+		if (ALT_HAS_CB(alt))
 			BUG_ON(alt->alt_len != 0);
 		else
 			BUG_ON(alt->alt_len != alt->orig_len);
 
-		pr_info_once("patching kernel code\n");
-
 		origptr = ALT_ORIG_PTR(alt);
 		updptr = is_module ? origptr : lm_alias(origptr);
 		nr_inst = alt->orig_len / AARCH64_INSN_SIZE;
 
-		if (alt->cpufeature < ARM64_CB_PATCH)
-			alt_cb = patch_alternative;
-		else
+		if (ALT_HAS_CB(alt))
 			alt_cb  = ALT_REPL_PTR(alt);
+		else
+			alt_cb = patch_alternative;
 
 		alt_cb(alt, origptr, updptr, nr_inst);
 
@@ -192,30 +196,55 @@ static void __nocfi __apply_alternatives(struct alt_region *region, bool is_modu
 	}
 }
 
+void apply_alternatives_vdso(void)
+{
+	struct alt_region region;
+	const struct elf64_hdr *hdr;
+	const struct elf64_shdr *shdr;
+	const struct elf64_shdr *alt;
+	DECLARE_BITMAP(all_capabilities, ARM64_NCAPS);
+
+	bitmap_fill(all_capabilities, ARM64_NCAPS);
+
+	hdr = (struct elf64_hdr *)vdso_start;
+	shdr = (void *)hdr + hdr->e_shoff;
+	alt = find_section(hdr, shdr, ".altinstructions");
+	if (!alt)
+		return;
+
+	region = (struct alt_region){
+		.begin	= (void *)hdr + alt->sh_offset,
+		.end	= (void *)hdr + alt->sh_offset + alt->sh_size,
+	};
+
+	__apply_alternatives(&region, false, &all_capabilities[0]);
+}
+
+static const struct alt_region kernel_alternatives = {
+	.begin	= (struct alt_instr *)__alt_instructions,
+	.end	= (struct alt_instr *)__alt_instructions_end,
+};
+
 /*
  * We might be patching the stop_machine state machine, so implement a
  * really simple polling protocol here.
  */
 static int __apply_alternatives_multi_stop(void *unused)
 {
-	struct alt_region region = {
-		.begin	= (struct alt_instr *)__alt_instructions,
-		.end	= (struct alt_instr *)__alt_instructions_end,
-	};
-
 	/* We always have a CPU 0 at this point (__init) */
 	if (smp_processor_id()) {
 		while (!all_alternatives_applied)
 			cpu_relax();
 		isb();
 	} else {
-		DECLARE_BITMAP(remaining_capabilities, ARM64_NPATCHABLE);
+		DECLARE_BITMAP(remaining_capabilities, ARM64_NCAPS);
 
 		bitmap_complement(remaining_capabilities, boot_capabilities,
-				  ARM64_NPATCHABLE);
+				  ARM64_NCAPS);
 
 		BUG_ON(all_alternatives_applied);
-		__apply_alternatives(&region, false, remaining_capabilities);
+		__apply_alternatives(&kernel_alternatives, false,
+				     remaining_capabilities);
 		/* Barriers provided by the cache flushing */
 		all_alternatives_applied = 1;
 	}
@@ -225,6 +254,9 @@ static int __apply_alternatives_multi_stop(void *unused)
 
 void __init apply_alternatives_all(void)
 {
+	pr_info("applying system-wide alternatives\n");
+
+	apply_alternatives_vdso();
 	/* better not try code patching on a live SMP system */
 	stop_machine(__apply_alternatives_multi_stop, NULL, cpu_online_mask);
 }
@@ -236,15 +268,13 @@ void __init apply_alternatives_all(void)
  */
 void __init apply_boot_alternatives(void)
 {
-	struct alt_region region = {
-		.begin	= (struct alt_instr *)__alt_instructions,
-		.end	= (struct alt_instr *)__alt_instructions_end,
-	};
-
 	/* If called on non-boot cpu things could go wrong */
 	WARN_ON(smp_processor_id() != 0);
 
-	__apply_alternatives(&region, false, &boot_capabilities[0]);
+	pr_info("applying boot alternatives\n");
+
+	__apply_alternatives(&kernel_alternatives, false,
+			     &boot_capabilities[0]);
 }
 
 #ifdef CONFIG_MODULES
@@ -254,10 +284,18 @@ void apply_alternatives_module(void *start, size_t length)
 		.begin	= start,
 		.end	= start + length,
 	};
-	DECLARE_BITMAP(all_capabilities, ARM64_NPATCHABLE);
+	DECLARE_BITMAP(all_capabilities, ARM64_NCAPS);
 
-	bitmap_fill(all_capabilities, ARM64_NPATCHABLE);
+	bitmap_fill(all_capabilities, ARM64_NCAPS);
 
 	__apply_alternatives(&region, true, &all_capabilities[0]);
 }
 #endif
+
+noinstr void alt_cb_patch_nops(struct alt_instr *alt, __le32 *origptr,
+			       __le32 *updptr, int nr_inst)
+{
+	for (int i = 0; i < nr_inst; i++)
+		updptr[i] = cpu_to_le32(aarch64_insn_gen_nop());
+}
+EXPORT_SYMBOL(alt_cb_patch_nops);
diff --git a/arch/arm64/kernel/armv8_deprecated.c b/arch/arm64/kernel/armv8_deprecated.c
index 6875a16b09d2..fb0e7c7b2e20 100644
--- a/arch/arm64/kernel/armv8_deprecated.c
+++ b/arch/arm64/kernel/armv8_deprecated.c
@@ -59,6 +59,7 @@ struct insn_emulation {
 static LIST_HEAD(insn_emulation);
 static int nr_insn_emulated __initdata;
 static DEFINE_RAW_SPINLOCK(insn_emulation_lock);
+static DEFINE_MUTEX(insn_emulation_mutex);
 
 static void register_emulation_hooks(struct insn_emulation_ops *ops)
 {
@@ -207,10 +208,10 @@ static int emulation_proc_handler(struct ctl_table *table, int write,
 				  loff_t *ppos)
 {
 	int ret = 0;
-	struct insn_emulation *insn = (struct insn_emulation *) table->data;
+	struct insn_emulation *insn = container_of(table->data, struct insn_emulation, current_mode);
 	enum insn_emulation_mode prev_mode = insn->current_mode;
 
-	table->data = &insn->current_mode;
+	mutex_lock(&insn_emulation_mutex);
 	ret = proc_dointvec_minmax(table, write, buffer, lenp, ppos);
 
 	if (ret || !write || prev_mode == insn->current_mode)
@@ -223,7 +224,7 @@ static int emulation_proc_handler(struct ctl_table *table, int write,
 		update_insn_emulation_mode(insn, INSN_UNDEF);
 	}
 ret:
-	table->data = insn;
+	mutex_unlock(&insn_emulation_mutex);
 	return ret;
 }
 
@@ -247,7 +248,7 @@ static void __init register_insn_emulation_sysctl(void)
 		sysctl->maxlen = sizeof(int);
 
 		sysctl->procname = insn->ops->name;
-		sysctl->data = insn;
+		sysctl->data = &insn->current_mode;
 		sysctl->extra1 = &insn->min;
 		sysctl->extra2 = &insn->max;
 		sysctl->proc_handler = emulation_proc_handler;
diff --git a/arch/arm64/kernel/asm-offsets.c b/arch/arm64/kernel/asm-offsets.c
index 6d0c3afd36b8..1197e7679882 100644
--- a/arch/arm64/kernel/asm-offsets.c
+++ b/arch/arm64/kernel/asm-offsets.c
@@ -111,7 +111,6 @@ int main(void)
 #ifdef CONFIG_KVM
   DEFINE(VCPU_CONTEXT,		offsetof(struct kvm_vcpu, arch.ctxt));
   DEFINE(VCPU_FAULT_DISR,	offsetof(struct kvm_vcpu, arch.fault.disr_el1));
-  DEFINE(VCPU_WORKAROUND_FLAGS,	offsetof(struct kvm_vcpu, arch.workaround_flags));
   DEFINE(VCPU_HCR_EL2,		offsetof(struct kvm_vcpu, arch.hcr_el2));
   DEFINE(CPU_USER_PT_REGS,	offsetof(struct kvm_cpu_context, regs));
   DEFINE(CPU_RGSR_EL1,		offsetof(struct kvm_cpu_context, sys_regs[RGSR_EL1]));
diff --git a/arch/arm64/kernel/cacheinfo.c b/arch/arm64/kernel/cacheinfo.c
index 587543c6c51c..97c42be71338 100644
--- a/arch/arm64/kernel/cacheinfo.c
+++ b/arch/arm64/kernel/cacheinfo.c
@@ -45,7 +45,8 @@ static void ci_leaf_init(struct cacheinfo *this_leaf,
 
 int init_cache_level(unsigned int cpu)
 {
-	unsigned int ctype, level, leaves, fw_level;
+	unsigned int ctype, level, leaves;
+	int fw_level;
 	struct cpu_cacheinfo *this_cpu_ci = get_cpu_cacheinfo(cpu);
 
 	for (level = 1, leaves = 0; level <= MAX_CACHE_LEVEL; level++) {
@@ -63,6 +64,9 @@ int init_cache_level(unsigned int cpu)
 	else
 		fw_level = acpi_find_last_cache_level(cpu);
 
+	if (fw_level < 0)
+		return fw_level;
+
 	if (level < fw_level) {
 		/*
 		 * some external caches not specified in CLIDR_EL1
diff --git a/arch/arm64/kernel/compat_alignment.c b/arch/arm64/kernel/compat_alignment.c
new file mode 100644
index 000000000000..5edec2f49ec9
--- /dev/null
+++ b/arch/arm64/kernel/compat_alignment.c
@@ -0,0 +1,387 @@
+// SPDX-License-Identifier: GPL-2.0-only
+// based on arch/arm/mm/alignment.c
+
+#include <linux/compiler.h>
+#include <linux/errno.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/perf_event.h>
+#include <linux/uaccess.h>
+
+#include <asm/exception.h>
+#include <asm/ptrace.h>
+#include <asm/traps.h>
+
+/*
+ * 32-bit misaligned trap handler (c) 1998 San Mehat (CCC) -July 1998
+ *
+ * Speed optimisations and better fault handling by Russell King.
+ */
+#define CODING_BITS(i)	(i & 0x0e000000)
+
+#define LDST_P_BIT(i)	(i & (1 << 24))		/* Preindex		*/
+#define LDST_U_BIT(i)	(i & (1 << 23))		/* Add offset		*/
+#define LDST_W_BIT(i)	(i & (1 << 21))		/* Writeback		*/
+#define LDST_L_BIT(i)	(i & (1 << 20))		/* Load			*/
+
+#define LDST_P_EQ_U(i)	((((i) ^ ((i) >> 1)) & (1 << 23)) == 0)
+
+#define LDSTHD_I_BIT(i)	(i & (1 << 22))		/* double/half-word immed */
+
+#define RN_BITS(i)	((i >> 16) & 15)	/* Rn			*/
+#define RD_BITS(i)	((i >> 12) & 15)	/* Rd			*/
+#define RM_BITS(i)	(i & 15)		/* Rm			*/
+
+#define REGMASK_BITS(i)	(i & 0xffff)
+
+#define BAD_INSTR 	0xdeadc0de
+
+/* Thumb-2 32 bit format per ARMv7 DDI0406A A6.3, either f800h,e800h,f800h */
+#define IS_T32(hi16) \
+	(((hi16) & 0xe000) == 0xe000 && ((hi16) & 0x1800))
+
+union offset_union {
+	unsigned long un;
+	  signed long sn;
+};
+
+#define TYPE_ERROR	0
+#define TYPE_FAULT	1
+#define TYPE_LDST	2
+#define TYPE_DONE	3
+
+static void
+do_alignment_finish_ldst(unsigned long addr, u32 instr, struct pt_regs *regs,
+			 union offset_union offset)
+{
+	if (!LDST_U_BIT(instr))
+		offset.un = -offset.un;
+
+	if (!LDST_P_BIT(instr))
+		addr += offset.un;
+
+	if (!LDST_P_BIT(instr) || LDST_W_BIT(instr))
+		regs->regs[RN_BITS(instr)] = addr;
+}
+
+static int
+do_alignment_ldrdstrd(unsigned long addr, u32 instr, struct pt_regs *regs)
+{
+	unsigned int rd = RD_BITS(instr);
+	unsigned int rd2;
+	int load;
+
+	if ((instr & 0xfe000000) == 0xe8000000) {
+		/* ARMv7 Thumb-2 32-bit LDRD/STRD */
+		rd2 = (instr >> 8) & 0xf;
+		load = !!(LDST_L_BIT(instr));
+	} else if (((rd & 1) == 1) || (rd == 14)) {
+		return TYPE_ERROR;
+	} else {
+		load = ((instr & 0xf0) == 0xd0);
+		rd2 = rd + 1;
+	}
+
+	if (load) {
+		unsigned int val, val2;
+
+		if (get_user(val, (u32 __user *)addr) ||
+		    get_user(val2, (u32 __user *)(addr + 4)))
+			return TYPE_FAULT;
+		regs->regs[rd] = val;
+		regs->regs[rd2] = val2;
+	} else {
+		if (put_user(regs->regs[rd], (u32 __user *)addr) ||
+		    put_user(regs->regs[rd2], (u32 __user *)(addr + 4)))
+			return TYPE_FAULT;
+	}
+	return TYPE_LDST;
+}
+
+/*
+ * LDM/STM alignment handler.
+ *
+ * There are 4 variants of this instruction:
+ *
+ * B = rn pointer before instruction, A = rn pointer after instruction
+ *              ------ increasing address ----->
+ *	        |    | r0 | r1 | ... | rx |    |
+ * PU = 01             B                    A
+ * PU = 11        B                    A
+ * PU = 00        A                    B
+ * PU = 10             A                    B
+ */
+static int
+do_alignment_ldmstm(unsigned long addr, u32 instr, struct pt_regs *regs)
+{
+	unsigned int rd, rn, nr_regs, regbits;
+	unsigned long eaddr, newaddr;
+	unsigned int val;
+
+	/* count the number of registers in the mask to be transferred */
+	nr_regs = hweight16(REGMASK_BITS(instr)) * 4;
+
+	rn = RN_BITS(instr);
+	newaddr = eaddr = regs->regs[rn];
+
+	if (!LDST_U_BIT(instr))
+		nr_regs = -nr_regs;
+	newaddr += nr_regs;
+	if (!LDST_U_BIT(instr))
+		eaddr = newaddr;
+
+	if (LDST_P_EQ_U(instr))	/* U = P */
+		eaddr += 4;
+
+	for (regbits = REGMASK_BITS(instr), rd = 0; regbits;
+	     regbits >>= 1, rd += 1)
+		if (regbits & 1) {
+			if (LDST_L_BIT(instr)) {
+				if (get_user(val, (u32 __user *)eaddr))
+					return TYPE_FAULT;
+				if (rd < 15)
+					regs->regs[rd] = val;
+				else
+					regs->pc = val;
+			} else {
+				/*
+				 * The PC register has a bias of +8 in ARM mode
+				 * and +4 in Thumb mode. This means that a read
+				 * of the value of PC should account for this.
+				 * Since Thumb does not permit STM instructions
+				 * to refer to PC, just add 8 here.
+				 */
+				val = (rd < 15) ? regs->regs[rd] : regs->pc + 8;
+				if (put_user(val, (u32 __user *)eaddr))
+					return TYPE_FAULT;
+			}
+			eaddr += 4;
+		}
+
+	if (LDST_W_BIT(instr))
+		regs->regs[rn] = newaddr;
+
+	return TYPE_DONE;
+}
+
+/*
+ * Convert Thumb multi-word load/store instruction forms to equivalent ARM
+ * instructions so we can reuse ARM userland alignment fault fixups for Thumb.
+ *
+ * This implementation was initially based on the algorithm found in
+ * gdb/sim/arm/thumbemu.c. It is basically just a code reduction of same
+ * to convert only Thumb ld/st instruction forms to equivalent ARM forms.
+ *
+ * NOTES:
+ * 1. Comments below refer to ARM ARM DDI0100E Thumb Instruction sections.
+ * 2. If for some reason we're passed an non-ld/st Thumb instruction to
+ *    decode, we return 0xdeadc0de. This should never happen under normal
+ *    circumstances but if it does, we've got other problems to deal with
+ *    elsewhere and we obviously can't fix those problems here.
+ */
+
+static unsigned long thumb2arm(u16 tinstr)
+{
+	u32 L = (tinstr & (1<<11)) >> 11;
+
+	switch ((tinstr & 0xf800) >> 11) {
+	/* 6.6.1 Format 1: */
+	case 0xc000 >> 11:				/* 7.1.51 STMIA */
+	case 0xc800 >> 11:				/* 7.1.25 LDMIA */
+		{
+			u32 Rn = (tinstr & (7<<8)) >> 8;
+			u32 W = ((L<<Rn) & (tinstr&255)) ? 0 : 1<<21;
+
+			return 0xe8800000 | W | (L<<20) | (Rn<<16) |
+				(tinstr&255);
+		}
+
+	/* 6.6.1 Format 2: */
+	case 0xb000 >> 11:				/* 7.1.48 PUSH */
+	case 0xb800 >> 11:				/* 7.1.47 POP */
+		if ((tinstr & (3 << 9)) == 0x0400) {
+			static const u32 subset[4] = {
+				0xe92d0000,	/* STMDB sp!,{registers} */
+				0xe92d4000,	/* STMDB sp!,{registers,lr} */
+				0xe8bd0000,	/* LDMIA sp!,{registers} */
+				0xe8bd8000	/* LDMIA sp!,{registers,pc} */
+			};
+			return subset[(L<<1) | ((tinstr & (1<<8)) >> 8)] |
+			    (tinstr & 255);		/* register_list */
+		}
+		fallthrough;	/* for illegal instruction case */
+
+	default:
+		return BAD_INSTR;
+	}
+}
+
+/*
+ * Convert Thumb-2 32 bit LDM, STM, LDRD, STRD to equivalent instruction
+ * handlable by ARM alignment handler, also find the corresponding handler,
+ * so that we can reuse ARM userland alignment fault fixups for Thumb.
+ *
+ * @pinstr: original Thumb-2 instruction; returns new handlable instruction
+ * @regs: register context.
+ * @poffset: return offset from faulted addr for later writeback
+ *
+ * NOTES:
+ * 1. Comments below refer to ARMv7 DDI0406A Thumb Instruction sections.
+ * 2. Register name Rt from ARMv7 is same as Rd from ARMv6 (Rd is Rt)
+ */
+static void *
+do_alignment_t32_to_handler(u32 *pinstr, struct pt_regs *regs,
+			    union offset_union *poffset)
+{
+	u32 instr = *pinstr;
+	u16 tinst1 = (instr >> 16) & 0xffff;
+	u16 tinst2 = instr & 0xffff;
+
+	switch (tinst1 & 0xffe0) {
+	/* A6.3.5 Load/Store multiple */
+	case 0xe880:		/* STM/STMIA/STMEA,LDM/LDMIA, PUSH/POP T2 */
+	case 0xe8a0:		/* ...above writeback version */
+	case 0xe900:		/* STMDB/STMFD, LDMDB/LDMEA */
+	case 0xe920:		/* ...above writeback version */
+		/* no need offset decision since handler calculates it */
+		return do_alignment_ldmstm;
+
+	case 0xf840:		/* POP/PUSH T3 (single register) */
+		if (RN_BITS(instr) == 13 && (tinst2 & 0x09ff) == 0x0904) {
+			u32 L = !!(LDST_L_BIT(instr));
+			const u32 subset[2] = {
+				0xe92d0000,	/* STMDB sp!,{registers} */
+				0xe8bd0000,	/* LDMIA sp!,{registers} */
+			};
+			*pinstr = subset[L] | (1<<RD_BITS(instr));
+			return do_alignment_ldmstm;
+		}
+		/* Else fall through for illegal instruction case */
+		break;
+
+	/* A6.3.6 Load/store double, STRD/LDRD(immed, lit, reg) */
+	case 0xe860:
+	case 0xe960:
+	case 0xe8e0:
+	case 0xe9e0:
+		poffset->un = (tinst2 & 0xff) << 2;
+		fallthrough;
+
+	case 0xe940:
+	case 0xe9c0:
+		return do_alignment_ldrdstrd;
+
+	/*
+	 * No need to handle load/store instructions up to word size
+	 * since ARMv6 and later CPUs can perform unaligned accesses.
+	 */
+	default:
+		break;
+	}
+	return NULL;
+}
+
+static int alignment_get_arm(struct pt_regs *regs, __le32 __user *ip, u32 *inst)
+{
+	__le32 instr = 0;
+	int fault;
+
+	fault = get_user(instr, ip);
+	if (fault)
+		return fault;
+
+	*inst = __le32_to_cpu(instr);
+	return 0;
+}
+
+static int alignment_get_thumb(struct pt_regs *regs, __le16 __user *ip, u16 *inst)
+{
+	__le16 instr = 0;
+	int fault;
+
+	fault = get_user(instr, ip);
+	if (fault)
+		return fault;
+
+	*inst = __le16_to_cpu(instr);
+	return 0;
+}
+
+int do_compat_alignment_fixup(unsigned long addr, struct pt_regs *regs)
+{
+	union offset_union offset;
+	unsigned long instrptr;
+	int (*handler)(unsigned long addr, u32 instr, struct pt_regs *regs);
+	unsigned int type;
+	u32 instr = 0;
+	u16 tinstr = 0;
+	int isize = 4;
+	int thumb2_32b = 0;
+	int fault;
+
+	instrptr = instruction_pointer(regs);
+
+	if (compat_thumb_mode(regs)) {
+		__le16 __user *ptr = (__le16 __user *)(instrptr & ~1);
+
+		fault = alignment_get_thumb(regs, ptr, &tinstr);
+		if (!fault) {
+			if (IS_T32(tinstr)) {
+				/* Thumb-2 32-bit */
+				u16 tinst2;
+				fault = alignment_get_thumb(regs, ptr + 1, &tinst2);
+				instr = ((u32)tinstr << 16) | tinst2;
+				thumb2_32b = 1;
+			} else {
+				isize = 2;
+				instr = thumb2arm(tinstr);
+			}
+		}
+	} else {
+		fault = alignment_get_arm(regs, (__le32 __user *)instrptr, &instr);
+	}
+
+	if (fault)
+		return 1;
+
+	switch (CODING_BITS(instr)) {
+	case 0x00000000:	/* 3.13.4 load/store instruction extensions */
+		if (LDSTHD_I_BIT(instr))
+			offset.un = (instr & 0xf00) >> 4 | (instr & 15);
+		else
+			offset.un = regs->regs[RM_BITS(instr)];
+
+		if ((instr & 0x001000f0) == 0x000000d0 || /* LDRD */
+		    (instr & 0x001000f0) == 0x000000f0)   /* STRD */
+			handler = do_alignment_ldrdstrd;
+		else
+			return 1;
+		break;
+
+	case 0x08000000:	/* ldm or stm, or thumb-2 32bit instruction */
+		if (thumb2_32b) {
+			offset.un = 0;
+			handler = do_alignment_t32_to_handler(&instr, regs, &offset);
+		} else {
+			offset.un = 0;
+			handler = do_alignment_ldmstm;
+		}
+		break;
+
+	default:
+		return 1;
+	}
+
+	type = handler(addr, instr, regs);
+
+	if (type == TYPE_ERROR || type == TYPE_FAULT)
+		return 1;
+
+	if (type == TYPE_LDST)
+		do_alignment_finish_ldst(addr, instr, regs, offset);
+
+	perf_sw_event(PERF_COUNT_SW_ALIGNMENT_FAULTS, 1, regs, regs->pc);
+	arm64_skip_faulting_instruction(regs, isize);
+
+	return 0;
+}
diff --git a/arch/arm64/kernel/cpu-reset.S b/arch/arm64/kernel/cpu-reset.S
index 48a8af97faa9..6b752fe89745 100644
--- a/arch/arm64/kernel/cpu-reset.S
+++ b/arch/arm64/kernel/cpu-reset.S
@@ -8,6 +8,7 @@
  */
 
 #include <linux/linkage.h>
+#include <linux/cfi_types.h>
 #include <asm/assembler.h>
 #include <asm/sysreg.h>
 #include <asm/virt.h>
@@ -28,7 +29,7 @@
  * branch to what would be the reset vector. It must be executed with the
  * flat identity mapping.
  */
-SYM_CODE_START(cpu_soft_restart)
+SYM_TYPED_FUNC_START(cpu_soft_restart)
 	mov_q	x12, INIT_SCTLR_EL1_MMU_OFF
 	pre_disable_mmu_workaround
 	/*
@@ -47,6 +48,6 @@ SYM_CODE_START(cpu_soft_restart)
 	mov	x1, x3				// arg1
 	mov	x2, x4				// arg2
 	br	x8
-SYM_CODE_END(cpu_soft_restart)
+SYM_FUNC_END(cpu_soft_restart)
 
 .popsection
diff --git a/arch/arm64/kernel/cpu_errata.c b/arch/arm64/kernel/cpu_errata.c
index 9e1c1aef9ebd..89ac00084f38 100644
--- a/arch/arm64/kernel/cpu_errata.c
+++ b/arch/arm64/kernel/cpu_errata.c
@@ -121,6 +121,22 @@ cpu_enable_cache_maint_trap(const struct arm64_cpu_capabilities *__unused)
 	sysreg_clear_set(sctlr_el1, SCTLR_EL1_UCI, 0);
 }
 
+static DEFINE_RAW_SPINLOCK(reg_user_mask_modification);
+static void __maybe_unused
+cpu_clear_bf16_from_user_emulation(const struct arm64_cpu_capabilities *__unused)
+{
+	struct arm64_ftr_reg *regp;
+
+	regp = get_arm64_ftr_reg(SYS_ID_AA64ISAR1_EL1);
+	if (!regp)
+		return;
+
+	raw_spin_lock(&reg_user_mask_modification);
+	if (regp->user_mask & ID_AA64ISAR1_EL1_BF16_MASK)
+		regp->user_mask &= ~ID_AA64ISAR1_EL1_BF16_MASK;
+	raw_spin_unlock(&reg_user_mask_modification);
+}
+
 #define CAP_MIDR_RANGE(model, v_min, r_min, v_max, r_max)	\
 	.matches = is_affected_midr_range,			\
 	.midr_range = MIDR_RANGE(model, v_min, r_min, v_max, r_max)
@@ -187,7 +203,7 @@ has_neoverse_n1_erratum_1542419(const struct arm64_cpu_capabilities *entry,
 				int scope)
 {
 	u32 midr = read_cpuid_id();
-	bool has_dic = read_cpuid_cachetype() & BIT(CTR_DIC_SHIFT);
+	bool has_dic = read_cpuid_cachetype() & BIT(CTR_EL0_DIC_SHIFT);
 	const struct midr_range range = MIDR_ALL_VERSIONS(MIDR_NEOVERSE_N1);
 
 	WARN_ON(scope != SCOPE_LOCAL_CPU || preemptible());
@@ -209,11 +225,41 @@ static const struct arm64_cpu_capabilities arm64_repeat_tlbi_list[] = {
 	{
 		ERRATA_MIDR_RANGE(MIDR_CORTEX_A76, 0, 0, 3, 0),
 	},
+	{
+		/* Kryo4xx Gold (rcpe to rfpe) => (r0p0 to r3p0) */
+		ERRATA_MIDR_RANGE(MIDR_QCOM_KRYO_4XX_GOLD, 0xc, 0xe, 0xf, 0xe),
+	},
+#endif
+#ifdef CONFIG_ARM64_ERRATUM_2441007
+	{
+		ERRATA_MIDR_ALL_VERSIONS(MIDR_CORTEX_A55),
+	},
+#endif
+#ifdef CONFIG_ARM64_ERRATUM_2441009
+	{
+		/* Cortex-A510 r0p0 -> r1p1. Fixed in r1p2 */
+		ERRATA_MIDR_RANGE(MIDR_CORTEX_A510, 0, 0, 1, 1),
+	},
 #endif
 	{},
 };
 #endif
 
+#ifdef CONFIG_CAVIUM_ERRATUM_23154
+static const struct midr_range cavium_erratum_23154_cpus[] = {
+	MIDR_ALL_VERSIONS(MIDR_THUNDERX),
+	MIDR_ALL_VERSIONS(MIDR_THUNDERX_81XX),
+	MIDR_ALL_VERSIONS(MIDR_THUNDERX_83XX),
+	MIDR_ALL_VERSIONS(MIDR_OCTX2_98XX),
+	MIDR_ALL_VERSIONS(MIDR_OCTX2_96XX),
+	MIDR_ALL_VERSIONS(MIDR_OCTX2_95XX),
+	MIDR_ALL_VERSIONS(MIDR_OCTX2_95XXN),
+	MIDR_ALL_VERSIONS(MIDR_OCTX2_95XXMM),
+	MIDR_ALL_VERSIONS(MIDR_OCTX2_95XXO),
+	{},
+};
+#endif
+
 #ifdef CONFIG_CAVIUM_ERRATUM_27456
 const struct midr_range cavium_erratum_27456_cpus[] = {
 	/* Cavium ThunderX, T88 pass 1.x - 2.1 */
@@ -347,6 +393,7 @@ static const struct midr_range trbe_overwrite_fill_mode_cpus[] = {
 #endif
 #ifdef CONFIG_ARM64_ERRATUM_2119858
 	MIDR_ALL_VERSIONS(MIDR_CORTEX_A710),
+	MIDR_RANGE(MIDR_CORTEX_X2, 0, 0, 2, 0),
 #endif
 	{},
 };
@@ -371,11 +418,20 @@ static struct midr_range trbe_write_out_of_range_cpus[] = {
 #endif
 #ifdef CONFIG_ARM64_ERRATUM_2224489
 	MIDR_ALL_VERSIONS(MIDR_CORTEX_A710),
+	MIDR_RANGE(MIDR_CORTEX_X2, 0, 0, 2, 0),
 #endif
 	{},
 };
 #endif /* CONFIG_ARM64_WORKAROUND_TRBE_WRITE_OUT_OF_RANGE */
 
+#ifdef CONFIG_ARM64_ERRATUM_1742098
+static struct midr_range broken_aarch32_aes[] = {
+	MIDR_RANGE(MIDR_CORTEX_A57, 0, 1, 0xf, 0xf),
+	MIDR_ALL_VERSIONS(MIDR_CORTEX_A72),
+	{},
+};
+#endif /* CONFIG_ARM64_WORKAROUND_TRBE_WRITE_OUT_OF_RANGE */
+
 const struct arm64_cpu_capabilities arm64_errata[] = {
 #ifdef CONFIG_ARM64_WORKAROUND_CLEAN_CACHE
 	{
@@ -423,10 +479,10 @@ const struct arm64_cpu_capabilities arm64_errata[] = {
 #endif
 #ifdef CONFIG_CAVIUM_ERRATUM_23154
 	{
-	/* Cavium ThunderX, pass 1.x */
-		.desc = "Cavium erratum 23154",
+		.desc = "Cavium errata 23154 and 38545",
 		.capability = ARM64_WORKAROUND_CAVIUM_23154,
-		ERRATA_MIDR_REV_RANGE(MIDR_THUNDERX, 0, 0, 1),
+		.type = ARM64_CPUCAP_LOCAL_CPU_ERRATUM,
+		ERRATA_MIDR_RANGE_LIST(cavium_erratum_23154_cpus),
 	},
 #endif
 #ifdef CONFIG_CAVIUM_ERRATUM_27456
@@ -461,7 +517,7 @@ const struct arm64_cpu_capabilities arm64_errata[] = {
 #endif
 #ifdef CONFIG_ARM64_WORKAROUND_REPEAT_TLBI
 	{
-		.desc = "Qualcomm erratum 1009, or ARM erratum 1286807",
+		.desc = "Qualcomm erratum 1009, or ARM erratum 1286807, 2441009",
 		.capability = ARM64_WORKAROUND_REPEAT_TLBI,
 		.type = ARM64_CPUCAP_LOCAL_CPU_ERRATUM,
 		.matches = cpucap_multi_entry_cap_matches,
@@ -500,6 +556,13 @@ const struct arm64_cpu_capabilities arm64_errata[] = {
 		.matches = has_spectre_v4,
 		.cpu_enable = spectre_v4_enable_mitigation,
 	},
+	{
+		.desc = "Spectre-BHB",
+		.capability = ARM64_SPECTRE_BHB,
+		.type = ARM64_CPUCAP_LOCAL_CPU_ERRATUM,
+		.matches = is_spectre_bhb_affected,
+		.cpu_enable = spectre_bhb_enable_mitigation,
+	},
 #ifdef CONFIG_ARM64_ERRATUM_1418040
 	{
 		.desc = "ARM erratum 1418040",
@@ -598,6 +661,68 @@ const struct arm64_cpu_capabilities arm64_errata[] = {
 		CAP_MIDR_RANGE_LIST(trbe_write_out_of_range_cpus),
 	},
 #endif
+#ifdef CONFIG_ARM64_ERRATUM_2077057
+	{
+		.desc = "ARM erratum 2077057",
+		.capability = ARM64_WORKAROUND_2077057,
+		ERRATA_MIDR_REV_RANGE(MIDR_CORTEX_A510, 0, 0, 2),
+	},
+#endif
+#ifdef CONFIG_ARM64_ERRATUM_2064142
+	{
+		.desc = "ARM erratum 2064142",
+		.capability = ARM64_WORKAROUND_2064142,
+
+		/* Cortex-A510 r0p0 - r0p2 */
+		ERRATA_MIDR_REV_RANGE(MIDR_CORTEX_A510, 0, 0, 2)
+	},
+#endif
+#ifdef CONFIG_ARM64_ERRATUM_2457168
+	{
+		.desc = "ARM erratum 2457168",
+		.capability = ARM64_WORKAROUND_2457168,
+		.type = ARM64_CPUCAP_WEAK_LOCAL_CPU_FEATURE,
+
+		/* Cortex-A510 r0p0-r1p1 */
+		CAP_MIDR_RANGE(MIDR_CORTEX_A510, 0, 0, 1, 1)
+	},
+#endif
+#ifdef CONFIG_ARM64_ERRATUM_2038923
+	{
+		.desc = "ARM erratum 2038923",
+		.capability = ARM64_WORKAROUND_2038923,
+
+		/* Cortex-A510 r0p0 - r0p2 */
+		ERRATA_MIDR_REV_RANGE(MIDR_CORTEX_A510, 0, 0, 2)
+	},
+#endif
+#ifdef CONFIG_ARM64_ERRATUM_1902691
+	{
+		.desc = "ARM erratum 1902691",
+		.capability = ARM64_WORKAROUND_1902691,
+
+		/* Cortex-A510 r0p0 - r0p1 */
+		ERRATA_MIDR_REV_RANGE(MIDR_CORTEX_A510, 0, 0, 1)
+	},
+#endif
+#ifdef CONFIG_ARM64_ERRATUM_1742098
+	{
+		.desc = "ARM erratum 1742098",
+		.capability = ARM64_WORKAROUND_1742098,
+		CAP_MIDR_RANGE_LIST(broken_aarch32_aes),
+		.type = ARM64_CPUCAP_LOCAL_CPU_ERRATUM,
+	},
+#endif
+#ifdef CONFIG_ARM64_ERRATUM_2658417
+	{
+		.desc = "ARM erratum 2658417",
+		.capability = ARM64_WORKAROUND_2658417,
+		/* Cortex-A510 r0p0 - r1p1 */
+		ERRATA_MIDR_RANGE(MIDR_CORTEX_A510, 0, 0, 1, 1),
+		MIDR_FIXED(MIDR_CPU_VAR_REV(1,1), BIT(25)),
+		.cpu_enable = cpu_clear_bf16_from_user_emulation,
+	},
+#endif
 	{
 	}
 };
diff --git a/arch/arm64/kernel/cpufeature.c b/arch/arm64/kernel/cpufeature.c
index 6f3e677d88f1..b3f37e2209ad 100644
--- a/arch/arm64/kernel/cpufeature.c
+++ b/arch/arm64/kernel/cpufeature.c
@@ -73,10 +73,13 @@
 #include <linux/mm.h>
 #include <linux/cpu.h>
 #include <linux/kasan.h>
+#include <linux/percpu.h>
+
 #include <asm/cpu.h>
 #include <asm/cpufeature.h>
 #include <asm/cpu_ops.h>
 #include <asm/fpsimd.h>
+#include <asm/hwcap.h>
 #include <asm/insn.h>
 #include <asm/kvm_host.h>
 #include <asm/mmu_context.h>
@@ -85,10 +88,11 @@
 #include <asm/smp.h>
 #include <asm/sysreg.h>
 #include <asm/traps.h>
+#include <asm/vectors.h>
 #include <asm/virt.h>
 
 /* Kernel representation of AT_HWCAP and AT_HWCAP2 */
-static unsigned long elf_hwcap __read_mostly;
+static DECLARE_BITMAP(elf_hwcap, MAX_CPU_FEATURES) __read_mostly;
 
 #ifdef CONFIG_COMPAT
 #define COMPAT_ELF_HWCAP_DEFAULT	\
@@ -104,12 +108,13 @@ DECLARE_BITMAP(cpu_hwcaps, ARM64_NCAPS);
 EXPORT_SYMBOL(cpu_hwcaps);
 static struct arm64_cpu_capabilities const __ro_after_init *cpu_hwcaps_ptrs[ARM64_NCAPS];
 
-/* Need also bit for ARM64_CB_PATCH */
-DECLARE_BITMAP(boot_capabilities, ARM64_NPATCHABLE);
+DECLARE_BITMAP(boot_capabilities, ARM64_NCAPS);
 
 bool arm64_use_ng_mappings = false;
 EXPORT_SYMBOL(arm64_use_ng_mappings);
 
+DEFINE_PER_CPU_READ_MOSTLY(const char *, this_cpu_vector) = vectors;
+
 /*
  * Permit PER_LINUX32 and execve() of 32-bit binaries even if not all CPUs
  * support it?
@@ -128,31 +133,12 @@ DEFINE_STATIC_KEY_FALSE(arm64_mismatched_32bit_el0);
  */
 static cpumask_var_t cpu_32bit_el0_mask __cpumask_var_read_mostly;
 
-/*
- * Flag to indicate if we have computed the system wide
- * capabilities based on the boot time active CPUs. This
- * will be used to determine if a new booting CPU should
- * go through the verification process to make sure that it
- * supports the system capabilities, without using a hotplug
- * notifier. This is also used to decide if we could use
- * the fast path for checking constant CPU caps.
- */
-DEFINE_STATIC_KEY_FALSE(arm64_const_caps_ready);
-EXPORT_SYMBOL(arm64_const_caps_ready);
-static inline void finalize_system_capabilities(void)
-{
-	static_branch_enable(&arm64_const_caps_ready);
-}
-
 void dump_cpu_features(void)
 {
 	/* file-wide pr_fmt adds "CPU features: " prefix */
 	pr_emerg("0x%*pb\n", ARM64_NCAPS, &cpu_hwcaps);
 }
 
-DEFINE_STATIC_KEY_ARRAY_FALSE(cpu_hwcap_keys, ARM64_NCAPS);
-EXPORT_SYMBOL(cpu_hwcap_keys);
-
 #define __ARM64_FTR_BITS(SIGNED, VISIBLE, STRICT, TYPE, SHIFT, WIDTH, SAFE_VAL) \
 	{						\
 		.sign = SIGNED,				\
@@ -186,102 +172,133 @@ static bool __system_matches_cap(unsigned int n);
  * sync with the documentation of the CPU feature register ABI.
  */
 static const struct arm64_ftr_bits ftr_id_aa64isar0[] = {
-	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64ISAR0_RNDR_SHIFT, 4, 0),
-	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64ISAR0_TLB_SHIFT, 4, 0),
-	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64ISAR0_TS_SHIFT, 4, 0),
-	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64ISAR0_FHM_SHIFT, 4, 0),
-	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64ISAR0_DP_SHIFT, 4, 0),
-	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64ISAR0_SM4_SHIFT, 4, 0),
-	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64ISAR0_SM3_SHIFT, 4, 0),
-	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64ISAR0_SHA3_SHIFT, 4, 0),
-	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64ISAR0_RDM_SHIFT, 4, 0),
-	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64ISAR0_ATOMICS_SHIFT, 4, 0),
-	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64ISAR0_CRC32_SHIFT, 4, 0),
-	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64ISAR0_SHA2_SHIFT, 4, 0),
-	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64ISAR0_SHA1_SHIFT, 4, 0),
-	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64ISAR0_AES_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64ISAR0_EL1_RNDR_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64ISAR0_EL1_TLB_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64ISAR0_EL1_TS_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64ISAR0_EL1_FHM_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64ISAR0_EL1_DP_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64ISAR0_EL1_SM4_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64ISAR0_EL1_SM3_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64ISAR0_EL1_SHA3_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64ISAR0_EL1_RDM_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64ISAR0_EL1_ATOMIC_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64ISAR0_EL1_CRC32_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64ISAR0_EL1_SHA2_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64ISAR0_EL1_SHA1_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64ISAR0_EL1_AES_SHIFT, 4, 0),
 	ARM64_FTR_END,
 };
 
 static const struct arm64_ftr_bits ftr_id_aa64isar1[] = {
-	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64ISAR1_I8MM_SHIFT, 4, 0),
-	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64ISAR1_DGH_SHIFT, 4, 0),
-	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64ISAR1_BF16_SHIFT, 4, 0),
-	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64ISAR1_SPECRES_SHIFT, 4, 0),
-	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64ISAR1_SB_SHIFT, 4, 0),
-	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64ISAR1_FRINTTS_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64ISAR1_EL1_I8MM_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64ISAR1_EL1_DGH_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64ISAR1_EL1_BF16_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64ISAR1_EL1_SPECRES_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64ISAR1_EL1_SB_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64ISAR1_EL1_FRINTTS_SHIFT, 4, 0),
 	ARM64_FTR_BITS(FTR_VISIBLE_IF_IS_ENABLED(CONFIG_ARM64_PTR_AUTH),
-		       FTR_STRICT, FTR_LOWER_SAFE, ID_AA64ISAR1_GPI_SHIFT, 4, 0),
+		       FTR_STRICT, FTR_LOWER_SAFE, ID_AA64ISAR1_EL1_GPI_SHIFT, 4, 0),
 	ARM64_FTR_BITS(FTR_VISIBLE_IF_IS_ENABLED(CONFIG_ARM64_PTR_AUTH),
-		       FTR_STRICT, FTR_LOWER_SAFE, ID_AA64ISAR1_GPA_SHIFT, 4, 0),
-	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64ISAR1_LRCPC_SHIFT, 4, 0),
-	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64ISAR1_FCMA_SHIFT, 4, 0),
-	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64ISAR1_JSCVT_SHIFT, 4, 0),
+		       FTR_STRICT, FTR_LOWER_SAFE, ID_AA64ISAR1_EL1_GPA_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64ISAR1_EL1_LRCPC_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64ISAR1_EL1_FCMA_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64ISAR1_EL1_JSCVT_SHIFT, 4, 0),
 	ARM64_FTR_BITS(FTR_VISIBLE_IF_IS_ENABLED(CONFIG_ARM64_PTR_AUTH),
-		       FTR_STRICT, FTR_EXACT, ID_AA64ISAR1_API_SHIFT, 4, 0),
+		       FTR_STRICT, FTR_EXACT, ID_AA64ISAR1_EL1_API_SHIFT, 4, 0),
 	ARM64_FTR_BITS(FTR_VISIBLE_IF_IS_ENABLED(CONFIG_ARM64_PTR_AUTH),
-		       FTR_STRICT, FTR_EXACT, ID_AA64ISAR1_APA_SHIFT, 4, 0),
-	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64ISAR1_DPB_SHIFT, 4, 0),
+		       FTR_STRICT, FTR_EXACT, ID_AA64ISAR1_EL1_APA_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64ISAR1_EL1_DPB_SHIFT, 4, 0),
+	ARM64_FTR_END,
+};
+
+static const struct arm64_ftr_bits ftr_id_aa64isar2[] = {
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_HIGHER_SAFE, ID_AA64ISAR2_EL1_BC_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_VISIBLE_IF_IS_ENABLED(CONFIG_ARM64_PTR_AUTH),
+		       FTR_STRICT, FTR_EXACT, ID_AA64ISAR2_EL1_APA3_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_VISIBLE_IF_IS_ENABLED(CONFIG_ARM64_PTR_AUTH),
+		       FTR_STRICT, FTR_LOWER_SAFE, ID_AA64ISAR2_EL1_GPA3_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_VISIBLE, FTR_NONSTRICT, FTR_LOWER_SAFE, ID_AA64ISAR2_EL1_RPRES_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_VISIBLE, FTR_NONSTRICT, FTR_LOWER_SAFE, ID_AA64ISAR2_EL1_WFxT_SHIFT, 4, 0),
 	ARM64_FTR_END,
 };
 
 static const struct arm64_ftr_bits ftr_id_aa64pfr0[] = {
-	ARM64_FTR_BITS(FTR_HIDDEN, FTR_NONSTRICT, FTR_LOWER_SAFE, ID_AA64PFR0_CSV3_SHIFT, 4, 0),
-	ARM64_FTR_BITS(FTR_HIDDEN, FTR_NONSTRICT, FTR_LOWER_SAFE, ID_AA64PFR0_CSV2_SHIFT, 4, 0),
-	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64PFR0_DIT_SHIFT, 4, 0),
-	ARM64_FTR_BITS(FTR_HIDDEN, FTR_NONSTRICT, FTR_LOWER_SAFE, ID_AA64PFR0_AMU_SHIFT, 4, 0),
-	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64PFR0_MPAM_SHIFT, 4, 0),
-	ARM64_FTR_BITS(FTR_HIDDEN, FTR_NONSTRICT, FTR_LOWER_SAFE, ID_AA64PFR0_SEL2_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_NONSTRICT, FTR_LOWER_SAFE, ID_AA64PFR0_EL1_CSV3_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_NONSTRICT, FTR_LOWER_SAFE, ID_AA64PFR0_EL1_CSV2_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64PFR0_EL1_DIT_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_NONSTRICT, FTR_LOWER_SAFE, ID_AA64PFR0_EL1_AMU_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64PFR0_EL1_MPAM_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_NONSTRICT, FTR_LOWER_SAFE, ID_AA64PFR0_EL1_SEL2_SHIFT, 4, 0),
 	ARM64_FTR_BITS(FTR_VISIBLE_IF_IS_ENABLED(CONFIG_ARM64_SVE),
-				   FTR_STRICT, FTR_LOWER_SAFE, ID_AA64PFR0_SVE_SHIFT, 4, 0),
-	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64PFR0_RAS_SHIFT, 4, 0),
-	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64PFR0_GIC_SHIFT, 4, 0),
-	S_ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64PFR0_ASIMD_SHIFT, 4, ID_AA64PFR0_ASIMD_NI),
-	S_ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64PFR0_FP_SHIFT, 4, ID_AA64PFR0_FP_NI),
-	ARM64_FTR_BITS(FTR_HIDDEN, FTR_NONSTRICT, FTR_LOWER_SAFE, ID_AA64PFR0_EL3_SHIFT, 4, 0),
-	ARM64_FTR_BITS(FTR_HIDDEN, FTR_NONSTRICT, FTR_LOWER_SAFE, ID_AA64PFR0_EL2_SHIFT, 4, 0),
-	ARM64_FTR_BITS(FTR_HIDDEN, FTR_NONSTRICT, FTR_LOWER_SAFE, ID_AA64PFR0_EL1_SHIFT, 4, ID_AA64PFR0_ELx_64BIT_ONLY),
-	ARM64_FTR_BITS(FTR_HIDDEN, FTR_NONSTRICT, FTR_LOWER_SAFE, ID_AA64PFR0_EL0_SHIFT, 4, ID_AA64PFR0_ELx_64BIT_ONLY),
+				   FTR_STRICT, FTR_LOWER_SAFE, ID_AA64PFR0_EL1_SVE_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64PFR0_EL1_RAS_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64PFR0_EL1_GIC_SHIFT, 4, 0),
+	S_ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64PFR0_EL1_AdvSIMD_SHIFT, 4, ID_AA64PFR0_EL1_AdvSIMD_NI),
+	S_ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64PFR0_EL1_FP_SHIFT, 4, ID_AA64PFR0_EL1_FP_NI),
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_NONSTRICT, FTR_LOWER_SAFE, ID_AA64PFR0_EL1_EL3_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_NONSTRICT, FTR_LOWER_SAFE, ID_AA64PFR0_EL1_EL2_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_NONSTRICT, FTR_LOWER_SAFE, ID_AA64PFR0_EL1_EL1_SHIFT, 4, ID_AA64PFR0_EL1_ELx_64BIT_ONLY),
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_NONSTRICT, FTR_LOWER_SAFE, ID_AA64PFR0_EL1_EL0_SHIFT, 4, ID_AA64PFR0_EL1_ELx_64BIT_ONLY),
 	ARM64_FTR_END,
 };
 
 static const struct arm64_ftr_bits ftr_id_aa64pfr1[] = {
-	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64PFR1_MPAMFRAC_SHIFT, 4, 0),
-	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64PFR1_RASFRAC_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_VISIBLE_IF_IS_ENABLED(CONFIG_ARM64_SME),
+		       FTR_STRICT, FTR_LOWER_SAFE, ID_AA64PFR1_EL1_SME_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64PFR1_EL1_MPAM_frac_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64PFR1_EL1_RAS_frac_SHIFT, 4, 0),
 	ARM64_FTR_BITS(FTR_VISIBLE_IF_IS_ENABLED(CONFIG_ARM64_MTE),
-		       FTR_STRICT, FTR_LOWER_SAFE, ID_AA64PFR1_MTE_SHIFT, 4, ID_AA64PFR1_MTE_NI),
-	ARM64_FTR_BITS(FTR_VISIBLE, FTR_NONSTRICT, FTR_LOWER_SAFE, ID_AA64PFR1_SSBS_SHIFT, 4, ID_AA64PFR1_SSBS_PSTATE_NI),
+		       FTR_STRICT, FTR_LOWER_SAFE, ID_AA64PFR1_EL1_MTE_SHIFT, 4, ID_AA64PFR1_EL1_MTE_NI),
+	ARM64_FTR_BITS(FTR_VISIBLE, FTR_NONSTRICT, FTR_LOWER_SAFE, ID_AA64PFR1_EL1_SSBS_SHIFT, 4, ID_AA64PFR1_EL1_SSBS_NI),
 	ARM64_FTR_BITS(FTR_VISIBLE_IF_IS_ENABLED(CONFIG_ARM64_BTI),
-				    FTR_STRICT, FTR_LOWER_SAFE, ID_AA64PFR1_BT_SHIFT, 4, 0),
+				    FTR_STRICT, FTR_LOWER_SAFE, ID_AA64PFR1_EL1_BT_SHIFT, 4, 0),
 	ARM64_FTR_END,
 };
 
 static const struct arm64_ftr_bits ftr_id_aa64zfr0[] = {
 	ARM64_FTR_BITS(FTR_VISIBLE_IF_IS_ENABLED(CONFIG_ARM64_SVE),
-		       FTR_STRICT, FTR_LOWER_SAFE, ID_AA64ZFR0_F64MM_SHIFT, 4, 0),
+		       FTR_STRICT, FTR_LOWER_SAFE, ID_AA64ZFR0_EL1_F64MM_SHIFT, 4, 0),
 	ARM64_FTR_BITS(FTR_VISIBLE_IF_IS_ENABLED(CONFIG_ARM64_SVE),
-		       FTR_STRICT, FTR_LOWER_SAFE, ID_AA64ZFR0_F32MM_SHIFT, 4, 0),
+		       FTR_STRICT, FTR_LOWER_SAFE, ID_AA64ZFR0_EL1_F32MM_SHIFT, 4, 0),
 	ARM64_FTR_BITS(FTR_VISIBLE_IF_IS_ENABLED(CONFIG_ARM64_SVE),
-		       FTR_STRICT, FTR_LOWER_SAFE, ID_AA64ZFR0_I8MM_SHIFT, 4, 0),
+		       FTR_STRICT, FTR_LOWER_SAFE, ID_AA64ZFR0_EL1_I8MM_SHIFT, 4, 0),
 	ARM64_FTR_BITS(FTR_VISIBLE_IF_IS_ENABLED(CONFIG_ARM64_SVE),
-		       FTR_STRICT, FTR_LOWER_SAFE, ID_AA64ZFR0_SM4_SHIFT, 4, 0),
+		       FTR_STRICT, FTR_LOWER_SAFE, ID_AA64ZFR0_EL1_SM4_SHIFT, 4, 0),
 	ARM64_FTR_BITS(FTR_VISIBLE_IF_IS_ENABLED(CONFIG_ARM64_SVE),
-		       FTR_STRICT, FTR_LOWER_SAFE, ID_AA64ZFR0_SHA3_SHIFT, 4, 0),
+		       FTR_STRICT, FTR_LOWER_SAFE, ID_AA64ZFR0_EL1_SHA3_SHIFT, 4, 0),
 	ARM64_FTR_BITS(FTR_VISIBLE_IF_IS_ENABLED(CONFIG_ARM64_SVE),
-		       FTR_STRICT, FTR_LOWER_SAFE, ID_AA64ZFR0_BF16_SHIFT, 4, 0),
+		       FTR_STRICT, FTR_LOWER_SAFE, ID_AA64ZFR0_EL1_BF16_SHIFT, 4, 0),
 	ARM64_FTR_BITS(FTR_VISIBLE_IF_IS_ENABLED(CONFIG_ARM64_SVE),
-		       FTR_STRICT, FTR_LOWER_SAFE, ID_AA64ZFR0_BITPERM_SHIFT, 4, 0),
+		       FTR_STRICT, FTR_LOWER_SAFE, ID_AA64ZFR0_EL1_BitPerm_SHIFT, 4, 0),
 	ARM64_FTR_BITS(FTR_VISIBLE_IF_IS_ENABLED(CONFIG_ARM64_SVE),
-		       FTR_STRICT, FTR_LOWER_SAFE, ID_AA64ZFR0_AES_SHIFT, 4, 0),
+		       FTR_STRICT, FTR_LOWER_SAFE, ID_AA64ZFR0_EL1_AES_SHIFT, 4, 0),
 	ARM64_FTR_BITS(FTR_VISIBLE_IF_IS_ENABLED(CONFIG_ARM64_SVE),
-		       FTR_STRICT, FTR_LOWER_SAFE, ID_AA64ZFR0_SVEVER_SHIFT, 4, 0),
+		       FTR_STRICT, FTR_LOWER_SAFE, ID_AA64ZFR0_EL1_SVEver_SHIFT, 4, 0),
+	ARM64_FTR_END,
+};
+
+static const struct arm64_ftr_bits ftr_id_aa64smfr0[] = {
+	ARM64_FTR_BITS(FTR_VISIBLE_IF_IS_ENABLED(CONFIG_ARM64_SME),
+		       FTR_STRICT, FTR_EXACT, ID_AA64SMFR0_EL1_FA64_SHIFT, 1, 0),
+	ARM64_FTR_BITS(FTR_VISIBLE_IF_IS_ENABLED(CONFIG_ARM64_SME),
+		       FTR_STRICT, FTR_EXACT, ID_AA64SMFR0_EL1_I16I64_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_VISIBLE_IF_IS_ENABLED(CONFIG_ARM64_SME),
+		       FTR_STRICT, FTR_EXACT, ID_AA64SMFR0_EL1_F64F64_SHIFT, 1, 0),
+	ARM64_FTR_BITS(FTR_VISIBLE_IF_IS_ENABLED(CONFIG_ARM64_SME),
+		       FTR_STRICT, FTR_EXACT, ID_AA64SMFR0_EL1_I8I32_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_VISIBLE_IF_IS_ENABLED(CONFIG_ARM64_SME),
+		       FTR_STRICT, FTR_EXACT, ID_AA64SMFR0_EL1_F16F32_SHIFT, 1, 0),
+	ARM64_FTR_BITS(FTR_VISIBLE_IF_IS_ENABLED(CONFIG_ARM64_SME),
+		       FTR_STRICT, FTR_EXACT, ID_AA64SMFR0_EL1_B16F32_SHIFT, 1, 0),
+	ARM64_FTR_BITS(FTR_VISIBLE_IF_IS_ENABLED(CONFIG_ARM64_SME),
+		       FTR_STRICT, FTR_EXACT, ID_AA64SMFR0_EL1_F32F32_SHIFT, 1, 0),
 	ARM64_FTR_END,
 };
 
 static const struct arm64_ftr_bits ftr_id_aa64mmfr0[] = {
-	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64MMFR0_ECV_SHIFT, 4, 0),
-	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64MMFR0_FGT_SHIFT, 4, 0),
-	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64MMFR0_EXS_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64MMFR0_EL1_ECV_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64MMFR0_EL1_FGT_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64MMFR0_EL1_EXS_SHIFT, 4, 0),
 	/*
 	 * Page size not being supported at Stage-2 is not fatal. You
 	 * just give up KVM if PAGE_SIZE isn't supported there. Go fix
@@ -297,9 +314,9 @@ static const struct arm64_ftr_bits ftr_id_aa64mmfr0[] = {
 	 * fields are inconsistent across vCPUs, then it isn't worth
 	 * trying to bring KVM up.
 	 */
-	ARM64_FTR_BITS(FTR_HIDDEN, FTR_NONSTRICT, FTR_EXACT, ID_AA64MMFR0_TGRAN4_2_SHIFT, 4, 1),
-	ARM64_FTR_BITS(FTR_HIDDEN, FTR_NONSTRICT, FTR_EXACT, ID_AA64MMFR0_TGRAN64_2_SHIFT, 4, 1),
-	ARM64_FTR_BITS(FTR_HIDDEN, FTR_NONSTRICT, FTR_EXACT, ID_AA64MMFR0_TGRAN16_2_SHIFT, 4, 1),
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_NONSTRICT, FTR_EXACT, ID_AA64MMFR0_EL1_TGRAN4_2_SHIFT, 4, 1),
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_NONSTRICT, FTR_EXACT, ID_AA64MMFR0_EL1_TGRAN64_2_SHIFT, 4, 1),
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_NONSTRICT, FTR_EXACT, ID_AA64MMFR0_EL1_TGRAN16_2_SHIFT, 4, 1),
 	/*
 	 * We already refuse to boot CPUs that don't support our configured
 	 * page size, so we can only detect mismatches for a page size other
@@ -307,70 +324,72 @@ static const struct arm64_ftr_bits ftr_id_aa64mmfr0[] = {
 	 * exist in the wild so, even though we don't like it, we'll have to go
 	 * along with it and treat them as non-strict.
 	 */
-	S_ARM64_FTR_BITS(FTR_HIDDEN, FTR_NONSTRICT, FTR_LOWER_SAFE, ID_AA64MMFR0_TGRAN4_SHIFT, 4, ID_AA64MMFR0_TGRAN4_NI),
-	S_ARM64_FTR_BITS(FTR_HIDDEN, FTR_NONSTRICT, FTR_LOWER_SAFE, ID_AA64MMFR0_TGRAN64_SHIFT, 4, ID_AA64MMFR0_TGRAN64_NI),
-	ARM64_FTR_BITS(FTR_HIDDEN, FTR_NONSTRICT, FTR_LOWER_SAFE, ID_AA64MMFR0_TGRAN16_SHIFT, 4, ID_AA64MMFR0_TGRAN16_NI),
+	S_ARM64_FTR_BITS(FTR_HIDDEN, FTR_NONSTRICT, FTR_LOWER_SAFE, ID_AA64MMFR0_EL1_TGRAN4_SHIFT, 4, ID_AA64MMFR0_EL1_TGRAN4_NI),
+	S_ARM64_FTR_BITS(FTR_HIDDEN, FTR_NONSTRICT, FTR_LOWER_SAFE, ID_AA64MMFR0_EL1_TGRAN64_SHIFT, 4, ID_AA64MMFR0_EL1_TGRAN64_NI),
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_NONSTRICT, FTR_LOWER_SAFE, ID_AA64MMFR0_EL1_TGRAN16_SHIFT, 4, ID_AA64MMFR0_EL1_TGRAN16_NI),
 
-	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64MMFR0_BIGENDEL0_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64MMFR0_EL1_BIGENDEL0_SHIFT, 4, 0),
 	/* Linux shouldn't care about secure memory */
-	ARM64_FTR_BITS(FTR_HIDDEN, FTR_NONSTRICT, FTR_LOWER_SAFE, ID_AA64MMFR0_SNSMEM_SHIFT, 4, 0),
-	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64MMFR0_BIGENDEL_SHIFT, 4, 0),
-	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64MMFR0_ASID_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_NONSTRICT, FTR_LOWER_SAFE, ID_AA64MMFR0_EL1_SNSMEM_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64MMFR0_EL1_BIGEND_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64MMFR0_EL1_ASIDBITS_SHIFT, 4, 0),
 	/*
 	 * Differing PARange is fine as long as all peripherals and memory are mapped
 	 * within the minimum PARange of all CPUs
 	 */
-	ARM64_FTR_BITS(FTR_HIDDEN, FTR_NONSTRICT, FTR_LOWER_SAFE, ID_AA64MMFR0_PARANGE_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_NONSTRICT, FTR_LOWER_SAFE, ID_AA64MMFR0_EL1_PARANGE_SHIFT, 4, 0),
 	ARM64_FTR_END,
 };
 
 static const struct arm64_ftr_bits ftr_id_aa64mmfr1[] = {
-	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64MMFR1_ETS_SHIFT, 4, 0),
-	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64MMFR1_TWED_SHIFT, 4, 0),
-	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64MMFR1_XNX_SHIFT, 4, 0),
-	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_HIGHER_SAFE, ID_AA64MMFR1_SPECSEI_SHIFT, 4, 0),
-	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64MMFR1_PAN_SHIFT, 4, 0),
-	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64MMFR1_LOR_SHIFT, 4, 0),
-	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64MMFR1_HPD_SHIFT, 4, 0),
-	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64MMFR1_VHE_SHIFT, 4, 0),
-	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64MMFR1_VMIDBITS_SHIFT, 4, 0),
-	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64MMFR1_HADBS_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_NONSTRICT, FTR_LOWER_SAFE, ID_AA64MMFR1_EL1_TIDCP1_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64MMFR1_EL1_AFP_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64MMFR1_EL1_ETS_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64MMFR1_EL1_TWED_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64MMFR1_EL1_XNX_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_HIGHER_SAFE, ID_AA64MMFR1_EL1_SpecSEI_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64MMFR1_EL1_PAN_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64MMFR1_EL1_LO_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64MMFR1_EL1_HPDS_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64MMFR1_EL1_VH_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64MMFR1_EL1_VMIDBits_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64MMFR1_EL1_HAFDBS_SHIFT, 4, 0),
 	ARM64_FTR_END,
 };
 
 static const struct arm64_ftr_bits ftr_id_aa64mmfr2[] = {
-	ARM64_FTR_BITS(FTR_HIDDEN, FTR_NONSTRICT, FTR_LOWER_SAFE, ID_AA64MMFR2_E0PD_SHIFT, 4, 0),
-	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64MMFR2_EVT_SHIFT, 4, 0),
-	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64MMFR2_BBM_SHIFT, 4, 0),
-	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64MMFR2_TTL_SHIFT, 4, 0),
-	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64MMFR2_FWB_SHIFT, 4, 0),
-	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64MMFR2_IDS_SHIFT, 4, 0),
-	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64MMFR2_AT_SHIFT, 4, 0),
-	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64MMFR2_ST_SHIFT, 4, 0),
-	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64MMFR2_NV_SHIFT, 4, 0),
-	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64MMFR2_CCIDX_SHIFT, 4, 0),
-	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64MMFR2_LVA_SHIFT, 4, 0),
-	ARM64_FTR_BITS(FTR_HIDDEN, FTR_NONSTRICT, FTR_LOWER_SAFE, ID_AA64MMFR2_IESB_SHIFT, 4, 0),
-	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64MMFR2_LSM_SHIFT, 4, 0),
-	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64MMFR2_UAO_SHIFT, 4, 0),
-	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64MMFR2_CNP_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_NONSTRICT, FTR_LOWER_SAFE, ID_AA64MMFR2_EL1_E0PD_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64MMFR2_EL1_EVT_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64MMFR2_EL1_BBM_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64MMFR2_EL1_TTL_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64MMFR2_EL1_FWB_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64MMFR2_EL1_IDS_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64MMFR2_EL1_AT_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64MMFR2_EL1_ST_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64MMFR2_EL1_NV_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64MMFR2_EL1_CCIDX_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64MMFR2_EL1_VARange_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_NONSTRICT, FTR_LOWER_SAFE, ID_AA64MMFR2_EL1_IESB_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64MMFR2_EL1_LSM_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64MMFR2_EL1_UAO_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64MMFR2_EL1_CnP_SHIFT, 4, 0),
 	ARM64_FTR_END,
 };
 
 static const struct arm64_ftr_bits ftr_ctr[] = {
 	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_EXACT, 31, 1, 1), /* RES1 */
-	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, CTR_DIC_SHIFT, 1, 1),
-	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, CTR_IDC_SHIFT, 1, 1),
-	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_HIGHER_OR_ZERO_SAFE, CTR_CWG_SHIFT, 4, 0),
-	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_HIGHER_OR_ZERO_SAFE, CTR_ERG_SHIFT, 4, 0),
-	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, CTR_DMINLINE_SHIFT, 4, 1),
+	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, CTR_EL0_DIC_SHIFT, 1, 1),
+	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, CTR_EL0_IDC_SHIFT, 1, 1),
+	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_HIGHER_OR_ZERO_SAFE, CTR_EL0_CWG_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_HIGHER_OR_ZERO_SAFE, CTR_EL0_ERG_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, CTR_EL0_DminLine_SHIFT, 4, 1),
 	/*
 	 * Linux can handle differing I-cache policies. Userspace JITs will
 	 * make use of *minLine.
 	 * If we have differing I-cache policies, report it as the weakest - VIPT.
 	 */
-	ARM64_FTR_BITS(FTR_VISIBLE, FTR_NONSTRICT, FTR_EXACT, CTR_L1IP_SHIFT, 2, ICACHE_POLICY_VIPT),	/* L1Ip */
-	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, CTR_IMINLINE_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_VISIBLE, FTR_NONSTRICT, FTR_EXACT, CTR_EL0_L1Ip_SHIFT, 2, CTR_EL0_L1Ip_VIPT),	/* L1Ip */
+	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, CTR_EL0_IminLine_SHIFT, 4, 0),
 	ARM64_FTR_END,
 };
 
@@ -395,17 +414,41 @@ static const struct arm64_ftr_bits ftr_id_mmfr0[] = {
 };
 
 static const struct arm64_ftr_bits ftr_id_aa64dfr0[] = {
-	S_ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64DFR0_DOUBLELOCK_SHIFT, 4, 0),
-	ARM64_FTR_BITS(FTR_HIDDEN, FTR_NONSTRICT, FTR_LOWER_SAFE, ID_AA64DFR0_PMSVER_SHIFT, 4, 0),
-	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64DFR0_CTX_CMPS_SHIFT, 4, 0),
-	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64DFR0_WRPS_SHIFT, 4, 0),
-	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64DFR0_BRPS_SHIFT, 4, 0),
+	S_ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64DFR0_EL1_DoubleLock_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_NONSTRICT, FTR_LOWER_SAFE, ID_AA64DFR0_EL1_PMSVer_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64DFR0_EL1_CTX_CMPs_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64DFR0_EL1_WRPs_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_AA64DFR0_EL1_BRPs_SHIFT, 4, 0),
 	/*
 	 * We can instantiate multiple PMU instances with different levels
 	 * of support.
 	 */
-	S_ARM64_FTR_BITS(FTR_HIDDEN, FTR_NONSTRICT, FTR_EXACT, ID_AA64DFR0_PMUVER_SHIFT, 4, 0),
-	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_EXACT, ID_AA64DFR0_DEBUGVER_SHIFT, 4, 0x6),
+	S_ARM64_FTR_BITS(FTR_HIDDEN, FTR_NONSTRICT, FTR_EXACT, ID_AA64DFR0_EL1_PMUVer_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_EXACT, ID_AA64DFR0_EL1_DebugVer_SHIFT, 4, 0x6),
+	ARM64_FTR_END,
+};
+
+static const struct arm64_ftr_bits ftr_mvfr0[] = {
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, MVFR0_FPROUND_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, MVFR0_FPSHVEC_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, MVFR0_FPSQRT_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, MVFR0_FPDIVIDE_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, MVFR0_FPTRAP_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, MVFR0_FPDP_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, MVFR0_FPSP_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, MVFR0_SIMD_SHIFT, 4, 0),
+	ARM64_FTR_END,
+};
+
+static const struct arm64_ftr_bits ftr_mvfr1[] = {
+	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, MVFR1_SIMDFMAC_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, MVFR1_FPHP_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, MVFR1_SIMDHP_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, MVFR1_SIMDSP_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, MVFR1_SIMDINT_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, MVFR1_SIMDLS_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, MVFR1_FPDNAN_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, MVFR1_FPFTZ_SHIFT, 4, 0),
 	ARM64_FTR_END,
 };
 
@@ -416,13 +459,13 @@ static const struct arm64_ftr_bits ftr_mvfr2[] = {
 };
 
 static const struct arm64_ftr_bits ftr_dczid[] = {
-	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_EXACT, DCZID_DZP_SHIFT, 1, 1),
-	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, DCZID_BS_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_EXACT, DCZID_EL0_DZP_SHIFT, 1, 1),
+	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, DCZID_EL0_BS_SHIFT, 4, 0),
 	ARM64_FTR_END,
 };
 
 static const struct arm64_ftr_bits ftr_gmid[] = {
-	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, SYS_GMID_EL1_BS_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, GMID_EL1_BS_SHIFT, 4, 0),
 	ARM64_FTR_END,
 };
 
@@ -439,10 +482,10 @@ static const struct arm64_ftr_bits ftr_id_isar0[] = {
 
 static const struct arm64_ftr_bits ftr_id_isar5[] = {
 	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_ISAR5_RDM_SHIFT, 4, 0),
-	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_ISAR5_CRC32_SHIFT, 4, 0),
-	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_ISAR5_SHA2_SHIFT, 4, 0),
-	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_ISAR5_SHA1_SHIFT, 4, 0),
-	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_ISAR5_AES_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, ID_ISAR5_CRC32_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, ID_ISAR5_SHA2_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, ID_ISAR5_SHA1_SHIFT, 4, 0),
+	ARM64_FTR_BITS(FTR_VISIBLE, FTR_STRICT, FTR_LOWER_SAFE, ID_ISAR5_AES_SHIFT, 4, 0),
 	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_ISAR5_SEVL_SHIFT, 4, 0),
 	ARM64_FTR_END,
 };
@@ -524,7 +567,7 @@ static const struct arm64_ftr_bits ftr_id_pfr2[] = {
 
 static const struct arm64_ftr_bits ftr_id_dfr0[] = {
 	/* [31:28] TraceFilt */
-	S_ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_DFR0_PERFMON_SHIFT, 4, 0xf),
+	S_ARM64_FTR_BITS(FTR_HIDDEN, FTR_NONSTRICT, FTR_EXACT, ID_DFR0_PERFMON_SHIFT, 4, 0),
 	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_DFR0_MPROFDBG_SHIFT, 4, 0),
 	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_DFR0_MMAPTRC_SHIFT, 4, 0),
 	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, ID_DFR0_COPTRC_SHIFT, 4, 0),
@@ -541,7 +584,13 @@ static const struct arm64_ftr_bits ftr_id_dfr1[] = {
 
 static const struct arm64_ftr_bits ftr_zcr[] = {
 	ARM64_FTR_BITS(FTR_HIDDEN, FTR_NONSTRICT, FTR_LOWER_SAFE,
-		ZCR_ELx_LEN_SHIFT, ZCR_ELx_LEN_SIZE, 0),	/* LEN */
+		ZCR_ELx_LEN_SHIFT, ZCR_ELx_LEN_WIDTH, 0),	/* LEN */
+	ARM64_FTR_END,
+};
+
+static const struct arm64_ftr_bits ftr_smcr[] = {
+	ARM64_FTR_BITS(FTR_HIDDEN, FTR_NONSTRICT, FTR_LOWER_SAFE,
+		SMCR_ELx_LEN_SHIFT, SMCR_ELx_LEN_WIDTH, 0),	/* LEN */
 	ARM64_FTR_END,
 };
 
@@ -549,7 +598,7 @@ static const struct arm64_ftr_bits ftr_zcr[] = {
  * Common ftr bits for a 32bit register with all hidden, strict
  * attributes, with 4bit feature fields and a default safe value of
  * 0. Covers the following 32bit registers:
- * id_isar[1-4], id_mmfr[1-3], id_pfr1, mvfr[0-1]
+ * id_isar[1-3], id_mmfr[1-3]
  */
 static const struct arm64_ftr_bits ftr_generic_32bits[] = {
 	ARM64_FTR_BITS(FTR_HIDDEN, FTR_STRICT, FTR_LOWER_SAFE, 28, 4, 0),
@@ -588,8 +637,12 @@ static const struct arm64_ftr_bits ftr_raz[] = {
 	__ARM64_FTR_REG_OVERRIDE(#id, id, table, &no_override)
 
 struct arm64_ftr_override __ro_after_init id_aa64mmfr1_override;
+struct arm64_ftr_override __ro_after_init id_aa64pfr0_override;
 struct arm64_ftr_override __ro_after_init id_aa64pfr1_override;
+struct arm64_ftr_override __ro_after_init id_aa64zfr0_override;
+struct arm64_ftr_override __ro_after_init id_aa64smfr0_override;
 struct arm64_ftr_override __ro_after_init id_aa64isar1_override;
+struct arm64_ftr_override __ro_after_init id_aa64isar2_override;
 
 static const struct __ftr_reg_entry {
 	u32			sys_id;
@@ -616,18 +669,22 @@ static const struct __ftr_reg_entry {
 	ARM64_FTR_REG(SYS_ID_ISAR6_EL1, ftr_id_isar6),
 
 	/* Op1 = 0, CRn = 0, CRm = 3 */
-	ARM64_FTR_REG(SYS_MVFR0_EL1, ftr_generic_32bits),
-	ARM64_FTR_REG(SYS_MVFR1_EL1, ftr_generic_32bits),
+	ARM64_FTR_REG(SYS_MVFR0_EL1, ftr_mvfr0),
+	ARM64_FTR_REG(SYS_MVFR1_EL1, ftr_mvfr1),
 	ARM64_FTR_REG(SYS_MVFR2_EL1, ftr_mvfr2),
 	ARM64_FTR_REG(SYS_ID_PFR2_EL1, ftr_id_pfr2),
 	ARM64_FTR_REG(SYS_ID_DFR1_EL1, ftr_id_dfr1),
 	ARM64_FTR_REG(SYS_ID_MMFR5_EL1, ftr_id_mmfr5),
 
 	/* Op1 = 0, CRn = 0, CRm = 4 */
-	ARM64_FTR_REG(SYS_ID_AA64PFR0_EL1, ftr_id_aa64pfr0),
+	ARM64_FTR_REG_OVERRIDE(SYS_ID_AA64PFR0_EL1, ftr_id_aa64pfr0,
+			       &id_aa64pfr0_override),
 	ARM64_FTR_REG_OVERRIDE(SYS_ID_AA64PFR1_EL1, ftr_id_aa64pfr1,
 			       &id_aa64pfr1_override),
-	ARM64_FTR_REG(SYS_ID_AA64ZFR0_EL1, ftr_id_aa64zfr0),
+	ARM64_FTR_REG_OVERRIDE(SYS_ID_AA64ZFR0_EL1, ftr_id_aa64zfr0,
+			       &id_aa64zfr0_override),
+	ARM64_FTR_REG_OVERRIDE(SYS_ID_AA64SMFR0_EL1, ftr_id_aa64smfr0,
+			       &id_aa64smfr0_override),
 
 	/* Op1 = 0, CRn = 0, CRm = 5 */
 	ARM64_FTR_REG(SYS_ID_AA64DFR0_EL1, ftr_id_aa64dfr0),
@@ -637,6 +694,8 @@ static const struct __ftr_reg_entry {
 	ARM64_FTR_REG(SYS_ID_AA64ISAR0_EL1, ftr_id_aa64isar0),
 	ARM64_FTR_REG_OVERRIDE(SYS_ID_AA64ISAR1_EL1, ftr_id_aa64isar1,
 			       &id_aa64isar1_override),
+	ARM64_FTR_REG_OVERRIDE(SYS_ID_AA64ISAR2_EL1, ftr_id_aa64isar2,
+			       &id_aa64isar2_override),
 
 	/* Op1 = 0, CRn = 0, CRm = 7 */
 	ARM64_FTR_REG(SYS_ID_AA64MMFR0_EL1, ftr_id_aa64mmfr0),
@@ -646,6 +705,7 @@ static const struct __ftr_reg_entry {
 
 	/* Op1 = 0, CRn = 1, CRm = 2 */
 	ARM64_FTR_REG(SYS_ZCR_EL1, ftr_zcr),
+	ARM64_FTR_REG(SYS_SMCR_EL1, ftr_smcr),
 
 	/* Op1 = 1, CRn = 0, CRm = 0 */
 	ARM64_FTR_REG(SYS_GMID_EL1, ftr_gmid),
@@ -694,7 +754,7 @@ static struct arm64_ftr_reg *get_arm64_ftr_reg_nowarn(u32 sys_id)
  * returns - Upon success,  matching ftr_reg entry for id.
  *         - NULL on failure but with an WARN_ON().
  */
-static struct arm64_ftr_reg *get_arm64_ftr_reg(u32 sys_id)
+struct arm64_ftr_reg *get_arm64_ftr_reg(u32 sys_id)
 {
 	struct arm64_ftr_reg *reg;
 
@@ -790,7 +850,7 @@ static void __init sort_ftr_regs(void)
 		 * to sys_id for subsequent binary search in get_arm64_ftr_reg()
 		 * to work correctly.
 		 */
-		BUG_ON(arm64_ftr_regs[i].sys_id < arm64_ftr_regs[i - 1].sys_id);
+		BUG_ON(arm64_ftr_regs[i].sys_id <= arm64_ftr_regs[i - 1].sys_id);
 	}
 }
 
@@ -933,21 +993,38 @@ void __init init_cpu_features(struct cpuinfo_arm64 *info)
 	init_cpu_ftr_reg(SYS_ID_AA64DFR1_EL1, info->reg_id_aa64dfr1);
 	init_cpu_ftr_reg(SYS_ID_AA64ISAR0_EL1, info->reg_id_aa64isar0);
 	init_cpu_ftr_reg(SYS_ID_AA64ISAR1_EL1, info->reg_id_aa64isar1);
+	init_cpu_ftr_reg(SYS_ID_AA64ISAR2_EL1, info->reg_id_aa64isar2);
 	init_cpu_ftr_reg(SYS_ID_AA64MMFR0_EL1, info->reg_id_aa64mmfr0);
 	init_cpu_ftr_reg(SYS_ID_AA64MMFR1_EL1, info->reg_id_aa64mmfr1);
 	init_cpu_ftr_reg(SYS_ID_AA64MMFR2_EL1, info->reg_id_aa64mmfr2);
 	init_cpu_ftr_reg(SYS_ID_AA64PFR0_EL1, info->reg_id_aa64pfr0);
 	init_cpu_ftr_reg(SYS_ID_AA64PFR1_EL1, info->reg_id_aa64pfr1);
 	init_cpu_ftr_reg(SYS_ID_AA64ZFR0_EL1, info->reg_id_aa64zfr0);
+	init_cpu_ftr_reg(SYS_ID_AA64SMFR0_EL1, info->reg_id_aa64smfr0);
 
 	if (id_aa64pfr0_32bit_el0(info->reg_id_aa64pfr0))
 		init_32bit_cpu_features(&info->aarch32);
 
-	if (id_aa64pfr0_sve(info->reg_id_aa64pfr0)) {
+	if (IS_ENABLED(CONFIG_ARM64_SVE) &&
+	    id_aa64pfr0_sve(read_sanitised_ftr_reg(SYS_ID_AA64PFR0_EL1))) {
+		info->reg_zcr = read_zcr_features();
 		init_cpu_ftr_reg(SYS_ZCR_EL1, info->reg_zcr);
 		vec_init_vq_map(ARM64_VEC_SVE);
 	}
 
+	if (IS_ENABLED(CONFIG_ARM64_SME) &&
+	    id_aa64pfr1_sme(read_sanitised_ftr_reg(SYS_ID_AA64PFR1_EL1))) {
+		info->reg_smcr = read_smcr_features();
+		/*
+		 * We mask out SMPS since even if the hardware
+		 * supports priorities the kernel does not at present
+		 * and we block access to them.
+		 */
+		info->reg_smidr = read_cpuid(SMIDR_EL1) & ~SMIDR_EL1_SMPS;
+		init_cpu_ftr_reg(SYS_SMCR_EL1, info->reg_smcr);
+		vec_init_vq_map(ARM64_VEC_SME);
+	}
+
 	if (id_aa64pfr1_mte(info->reg_id_aa64pfr1))
 		init_cpu_ftr_reg(SYS_GMID_EL1, info->reg_gmid);
 
@@ -1151,6 +1228,8 @@ void update_cpu_features(int cpu,
 				      info->reg_id_aa64isar0, boot->reg_id_aa64isar0);
 	taint |= check_update_ftr_reg(SYS_ID_AA64ISAR1_EL1, cpu,
 				      info->reg_id_aa64isar1, boot->reg_id_aa64isar1);
+	taint |= check_update_ftr_reg(SYS_ID_AA64ISAR2_EL1, cpu,
+				      info->reg_id_aa64isar2, boot->reg_id_aa64isar2);
 
 	/*
 	 * Differing PARange support is fine as long as all peripherals and
@@ -1172,16 +1251,37 @@ void update_cpu_features(int cpu,
 	taint |= check_update_ftr_reg(SYS_ID_AA64ZFR0_EL1, cpu,
 				      info->reg_id_aa64zfr0, boot->reg_id_aa64zfr0);
 
-	if (id_aa64pfr0_sve(info->reg_id_aa64pfr0)) {
+	taint |= check_update_ftr_reg(SYS_ID_AA64SMFR0_EL1, cpu,
+				      info->reg_id_aa64smfr0, boot->reg_id_aa64smfr0);
+
+	if (IS_ENABLED(CONFIG_ARM64_SVE) &&
+	    id_aa64pfr0_sve(read_sanitised_ftr_reg(SYS_ID_AA64PFR0_EL1))) {
+		info->reg_zcr = read_zcr_features();
 		taint |= check_update_ftr_reg(SYS_ZCR_EL1, cpu,
 					info->reg_zcr, boot->reg_zcr);
 
-		/* Probe vector lengths, unless we already gave up on SVE */
-		if (id_aa64pfr0_sve(read_sanitised_ftr_reg(SYS_ID_AA64PFR0_EL1)) &&
-		    !system_capabilities_finalized())
+		/* Probe vector lengths */
+		if (!system_capabilities_finalized())
 			vec_update_vq_map(ARM64_VEC_SVE);
 	}
 
+	if (IS_ENABLED(CONFIG_ARM64_SME) &&
+	    id_aa64pfr1_sme(read_sanitised_ftr_reg(SYS_ID_AA64PFR1_EL1))) {
+		info->reg_smcr = read_smcr_features();
+		/*
+		 * We mask out SMPS since even if the hardware
+		 * supports priorities the kernel does not at present
+		 * and we block access to them.
+		 */
+		info->reg_smidr = read_cpuid(SMIDR_EL1) & ~SMIDR_EL1_SMPS;
+		taint |= check_update_ftr_reg(SYS_SMCR_EL1, cpu,
+					info->reg_smcr, boot->reg_smcr);
+
+		/* Probe vector lengths */
+		if (!system_capabilities_finalized())
+			vec_update_vq_map(ARM64_VEC_SME);
+	}
+
 	/*
 	 * The kernel uses the LDGM/STGM instructions and the number of tags
 	 * they read/write depends on the GMID_EL1.BS field. Check that the
@@ -1265,6 +1365,7 @@ u64 __read_sysreg_by_encoding(u32 sys_id)
 	read_sysreg_case(SYS_ID_AA64PFR0_EL1);
 	read_sysreg_case(SYS_ID_AA64PFR1_EL1);
 	read_sysreg_case(SYS_ID_AA64ZFR0_EL1);
+	read_sysreg_case(SYS_ID_AA64SMFR0_EL1);
 	read_sysreg_case(SYS_ID_AA64DFR0_EL1);
 	read_sysreg_case(SYS_ID_AA64DFR1_EL1);
 	read_sysreg_case(SYS_ID_AA64MMFR0_EL1);
@@ -1272,6 +1373,7 @@ u64 __read_sysreg_by_encoding(u32 sys_id)
 	read_sysreg_case(SYS_ID_AA64MMFR2_EL1);
 	read_sysreg_case(SYS_ID_AA64ISAR0_EL1);
 	read_sysreg_case(SYS_ID_AA64ISAR1_EL1);
+	read_sysreg_case(SYS_ID_AA64ISAR2_EL1);
 
 	read_sysreg_case(SYS_CNTFRQ_EL0);
 	read_sysreg_case(SYS_CTR_EL0);
@@ -1294,24 +1396,55 @@ u64 __read_sysreg_by_encoding(u32 sys_id)
 #include <linux/irqchip/arm-gic-v3.h>
 
 static bool
+has_always(const struct arm64_cpu_capabilities *entry, int scope)
+{
+	return true;
+}
+
+static bool
 feature_matches(u64 reg, const struct arm64_cpu_capabilities *entry)
 {
-	int val = cpuid_feature_extract_field(reg, entry->field_pos, entry->sign);
+	int val = cpuid_feature_extract_field_width(reg, entry->field_pos,
+						    entry->field_width,
+						    entry->sign);
 
 	return val >= entry->min_field_value;
 }
 
-static bool
-has_cpuid_feature(const struct arm64_cpu_capabilities *entry, int scope)
+static u64
+read_scoped_sysreg(const struct arm64_cpu_capabilities *entry, int scope)
 {
-	u64 val;
-
 	WARN_ON(scope == SCOPE_LOCAL_CPU && preemptible());
 	if (scope == SCOPE_SYSTEM)
-		val = read_sanitised_ftr_reg(entry->sys_reg);
+		return read_sanitised_ftr_reg(entry->sys_reg);
 	else
-		val = __read_sysreg_by_encoding(entry->sys_reg);
+		return __read_sysreg_by_encoding(entry->sys_reg);
+}
+
+static bool
+has_user_cpuid_feature(const struct arm64_cpu_capabilities *entry, int scope)
+{
+	int mask;
+	struct arm64_ftr_reg *regp;
+	u64 val = read_scoped_sysreg(entry, scope);
+
+	regp = get_arm64_ftr_reg(entry->sys_reg);
+	if (!regp)
+		return false;
+
+	mask = cpuid_feature_extract_unsigned_field_width(regp->user_mask,
+							  entry->field_pos,
+							  entry->field_width);
+	if (!mask)
+		return false;
+
+	return feature_matches(val, entry);
+}
 
+static bool
+has_cpuid_feature(const struct arm64_cpu_capabilities *entry, int scope)
+{
+	u64 val = read_scoped_sysreg(entry, scope);
 	return feature_matches(val, entry);
 }
 
@@ -1392,7 +1525,7 @@ static bool has_no_fpsimd(const struct arm64_cpu_capabilities *entry, int __unus
 	u64 pfr0 = read_sanitised_ftr_reg(SYS_ID_AA64PFR0_EL1);
 
 	return cpuid_feature_extract_signed_field(pfr0,
-					ID_AA64PFR0_FP_SHIFT) < 0;
+					ID_AA64PFR0_EL1_FP_SHIFT) < 0;
 }
 
 static bool has_cache_idc(const struct arm64_cpu_capabilities *entry,
@@ -1405,7 +1538,7 @@ static bool has_cache_idc(const struct arm64_cpu_capabilities *entry,
 	else
 		ctr = read_cpuid_effective_cachetype();
 
-	return ctr & BIT(CTR_IDC_SHIFT);
+	return ctr & BIT(CTR_EL0_IDC_SHIFT);
 }
 
 static void cpu_emulate_effective_ctr(const struct arm64_cpu_capabilities *__unused)
@@ -1416,7 +1549,7 @@ static void cpu_emulate_effective_ctr(const struct arm64_cpu_capabilities *__unu
 	 * to the CTR_EL0 on this CPU and emulate it with the real/safe
 	 * value.
 	 */
-	if (!(read_cpuid_cachetype() & BIT(CTR_IDC_SHIFT)))
+	if (!(read_cpuid_cachetype() & BIT(CTR_EL0_IDC_SHIFT)))
 		sysreg_clear_set(sctlr_el1, SCTLR_EL1_UCT, 0);
 }
 
@@ -1430,7 +1563,7 @@ static bool has_cache_dic(const struct arm64_cpu_capabilities *entry,
 	else
 		ctr = read_cpuid_cachetype();
 
-	return ctr & BIT(CTR_DIC_SHIFT);
+	return ctr & BIT(CTR_EL0_DIC_SHIFT);
 }
 
 static bool __maybe_unused
@@ -1471,7 +1604,7 @@ bool kaslr_requires_kpti(void)
 	if (IS_ENABLED(CONFIG_ARM64_E0PD)) {
 		u64 mmfr2 = read_sysreg_s(SYS_ID_AA64MMFR2_EL1);
 		if (cpuid_feature_extract_unsigned_field(mmfr2,
-						ID_AA64MMFR2_E0PD_SHIFT))
+						ID_AA64MMFR2_EL1_E0PD_SHIFT))
 			return false;
 	}
 
@@ -1570,14 +1703,40 @@ static bool unmap_kernel_at_el0(const struct arm64_cpu_capabilities *entry,
 }
 
 #ifdef CONFIG_UNMAP_KERNEL_AT_EL0
-static void __nocfi
+#define KPTI_NG_TEMP_VA		(-(1UL << PMD_SHIFT))
+
+extern
+void create_kpti_ng_temp_pgd(pgd_t *pgdir, phys_addr_t phys, unsigned long virt,
+			     phys_addr_t size, pgprot_t prot,
+			     phys_addr_t (*pgtable_alloc)(int), int flags);
+
+static phys_addr_t kpti_ng_temp_alloc;
+
+static phys_addr_t kpti_ng_pgd_alloc(int shift)
+{
+	kpti_ng_temp_alloc -= PAGE_SIZE;
+	return kpti_ng_temp_alloc;
+}
+
+static void
 kpti_install_ng_mappings(const struct arm64_cpu_capabilities *__unused)
 {
-	typedef void (kpti_remap_fn)(int, int, phys_addr_t);
+	typedef void (kpti_remap_fn)(int, int, phys_addr_t, unsigned long);
 	extern kpti_remap_fn idmap_kpti_install_ng_mappings;
 	kpti_remap_fn *remap_fn;
 
 	int cpu = smp_processor_id();
+	int levels = CONFIG_PGTABLE_LEVELS;
+	int order = order_base_2(levels);
+	u64 kpti_ng_temp_pgd_pa = 0;
+	pgd_t *kpti_ng_temp_pgd;
+	u64 alloc = 0;
+
+	if (__this_cpu_read(this_cpu_vector) == vectors) {
+		const char *v = arm64_get_bp_hardening_vector(EL1_VECTOR_KPTI);
+
+		__this_cpu_write(this_cpu_vector, v);
+	}
 
 	/*
 	 * We don't need to rewrite the page-tables if either we've done
@@ -1587,14 +1746,42 @@ kpti_install_ng_mappings(const struct arm64_cpu_capabilities *__unused)
 	if (arm64_use_ng_mappings)
 		return;
 
-	remap_fn = (void *)__pa_symbol(function_nocfi(idmap_kpti_install_ng_mappings));
+	remap_fn = (void *)__pa_symbol(idmap_kpti_install_ng_mappings);
+
+	if (!cpu) {
+		alloc = __get_free_pages(GFP_ATOMIC | __GFP_ZERO, order);
+		kpti_ng_temp_pgd = (pgd_t *)(alloc + (levels - 1) * PAGE_SIZE);
+		kpti_ng_temp_alloc = kpti_ng_temp_pgd_pa = __pa(kpti_ng_temp_pgd);
+
+		//
+		// Create a minimal page table hierarchy that permits us to map
+		// the swapper page tables temporarily as we traverse them.
+		//
+		// The physical pages are laid out as follows:
+		//
+		// +--------+-/-------+-/------ +-\\--------+
+		// :  PTE[] : | PMD[] : | PUD[] : || PGD[]  :
+		// +--------+-\-------+-\------ +-//--------+
+		//      ^
+		// The first page is mapped into this hierarchy at a PMD_SHIFT
+		// aligned virtual address, so that we can manipulate the PTE
+		// level entries while the mapping is active. The first entry
+		// covers the PTE[] page itself, the remaining entries are free
+		// to be used as a ad-hoc fixmap.
+		//
+		create_kpti_ng_temp_pgd(kpti_ng_temp_pgd, __pa(alloc),
+					KPTI_NG_TEMP_VA, PAGE_SIZE, PAGE_KERNEL,
+					kpti_ng_pgd_alloc, 0);
+	}
 
 	cpu_install_idmap();
-	remap_fn(cpu, num_online_cpus(), __pa_symbol(swapper_pg_dir));
+	remap_fn(cpu, num_online_cpus(), kpti_ng_temp_pgd_pa, KPTI_NG_TEMP_VA);
 	cpu_uninstall_idmap();
 
-	if (!cpu)
+	if (!cpu) {
+		free_pages(alloc, order);
 		arm64_use_ng_mappings = true;
+	}
 }
 #else
 static void
@@ -1635,6 +1822,9 @@ static bool cpu_has_broken_dbm(void)
 		/* Kryo4xx Silver (rdpe => r1p0) */
 		MIDR_REV(MIDR_QCOM_KRYO_4XX_SILVER, 0xd, 0xe),
 #endif
+#ifdef CONFIG_ARM64_ERRATUM_2051678
+		MIDR_REV_RANGE(MIDR_CORTEX_A510, 0, 0, 2),
+#endif
 		{},
 	};
 
@@ -1713,7 +1903,10 @@ static void cpu_amu_enable(struct arm64_cpu_capabilities const *cap)
 		pr_info("detected CPU%d: Activity Monitors Unit (AMU)\n",
 			smp_processor_id());
 		cpumask_set_cpu(smp_processor_id(), &amu_cpus);
-		update_freq_counters_refs();
+
+		/* 0 reference values signal broken/disabled counters */
+		if (!this_cpu_has_cap(ARM64_WORKAROUND_2457168))
+			update_freq_counters_refs();
 	}
 }
 
@@ -1761,14 +1954,6 @@ static void cpu_copy_el2regs(const struct arm64_cpu_capabilities *__unused)
 		write_sysreg(read_sysreg(tpidr_el1), tpidr_el2);
 }
 
-static void cpu_has_fwb(const struct arm64_cpu_capabilities *__unused)
-{
-	u64 val = read_sysreg_s(SYS_CLIDR_EL1);
-
-	/* Check that CLIDR_EL1.LOU{U,IS} are both 0 */
-	WARN_ON(CLIDR_LOUU(val) || CLIDR_LOUIS(val));
-}
-
 #ifdef CONFIG_ARM64_PAN
 static void cpu_enable_pan(const struct arm64_cpu_capabilities *__unused)
 {
@@ -1815,21 +2000,27 @@ static bool has_address_auth_cpucap(const struct arm64_cpu_capabilities *entry,
 	/* Now check for the secondary CPUs with SCOPE_LOCAL_CPU scope */
 	sec_val = cpuid_feature_extract_field(__read_sysreg_by_encoding(entry->sys_reg),
 					      entry->field_pos, entry->sign);
-	return sec_val == boot_val;
+	return (sec_val >= entry->min_field_value) && (sec_val == boot_val);
 }
 
 static bool has_address_auth_metacap(const struct arm64_cpu_capabilities *entry,
 				     int scope)
 {
-	return has_address_auth_cpucap(cpu_hwcaps_ptrs[ARM64_HAS_ADDRESS_AUTH_ARCH], scope) ||
-	       has_address_auth_cpucap(cpu_hwcaps_ptrs[ARM64_HAS_ADDRESS_AUTH_IMP_DEF], scope);
+	bool api = has_address_auth_cpucap(cpu_hwcaps_ptrs[ARM64_HAS_ADDRESS_AUTH_IMP_DEF], scope);
+	bool apa = has_address_auth_cpucap(cpu_hwcaps_ptrs[ARM64_HAS_ADDRESS_AUTH_ARCH_QARMA5], scope);
+	bool apa3 = has_address_auth_cpucap(cpu_hwcaps_ptrs[ARM64_HAS_ADDRESS_AUTH_ARCH_QARMA3], scope);
+
+	return apa || apa3 || api;
 }
 
 static bool has_generic_auth(const struct arm64_cpu_capabilities *entry,
 			     int __unused)
 {
-	return __system_matches_cap(ARM64_HAS_GENERIC_AUTH_ARCH) ||
-	       __system_matches_cap(ARM64_HAS_GENERIC_AUTH_IMP_DEF);
+	bool gpi = __system_matches_cap(ARM64_HAS_GENERIC_AUTH_IMP_DEF);
+	bool gpa = __system_matches_cap(ARM64_HAS_GENERIC_AUTH_ARCH_QARMA5);
+	bool gpa3 = __system_matches_cap(ARM64_HAS_GENERIC_AUTH_ARCH_QARMA3);
+
+	return gpa || gpa3 || gpi;
 }
 #endif /* CONFIG_ARM64_PTR_AUTH */
 
@@ -1876,7 +2067,8 @@ static void bti_enable(const struct arm64_cpu_capabilities *__unused)
 static void cpu_enable_mte(struct arm64_cpu_capabilities const *cap)
 {
 	sysreg_clear_set(sctlr_el1, 0, SCTLR_ELx_ATA | SCTLR_EL1_ATA0);
-	isb();
+
+	mte_cpu_setup();
 
 	/*
 	 * Clear the tags in the zero page. This needs to be done via the
@@ -1889,21 +2081,26 @@ static void cpu_enable_mte(struct arm64_cpu_capabilities const *cap)
 }
 #endif /* CONFIG_ARM64_MTE */
 
+static void elf_hwcap_fixup(void)
+{
+#ifdef CONFIG_ARM64_ERRATUM_1742098
+	if (cpus_have_const_cap(ARM64_WORKAROUND_1742098))
+		compat_elf_hwcap2 &= ~COMPAT_HWCAP2_AES;
+#endif /* ARM64_ERRATUM_1742098 */
+}
+
 #ifdef CONFIG_KVM
 static bool is_kvm_protected_mode(const struct arm64_cpu_capabilities *entry, int __unused)
 {
-	if (kvm_get_mode() != KVM_MODE_PROTECTED)
-		return false;
-
-	if (is_kernel_in_hyp_mode()) {
-		pr_warn("Protected KVM not available with VHE\n");
-		return false;
-	}
-
-	return true;
+	return kvm_get_mode() == KVM_MODE_PROTECTED;
 }
 #endif /* CONFIG_KVM */
 
+static void cpu_trap_el0_impdef(const struct arm64_cpu_capabilities *__unused)
+{
+	sysreg_clear_set(sctlr_el1, 0, SCTLR_EL1_TIDCP);
+}
+
 /* Internal helper functions to match cpu capability type */
 static bool
 cpucap_late_cpu_optional(const struct arm64_cpu_capabilities *cap)
@@ -1925,12 +2122,23 @@ cpucap_panic_on_conflict(const struct arm64_cpu_capabilities *cap)
 
 static const struct arm64_cpu_capabilities arm64_features[] = {
 	{
+		.capability = ARM64_ALWAYS_BOOT,
+		.type = ARM64_CPUCAP_BOOT_CPU_FEATURE,
+		.matches = has_always,
+	},
+	{
+		.capability = ARM64_ALWAYS_SYSTEM,
+		.type = ARM64_CPUCAP_SYSTEM_FEATURE,
+		.matches = has_always,
+	},
+	{
 		.desc = "GIC system register CPU interface",
 		.capability = ARM64_HAS_SYSREG_GIC_CPUIF,
 		.type = ARM64_CPUCAP_STRICT_BOOT_CPU_FEATURE,
 		.matches = has_useable_gicv3_cpuif,
 		.sys_reg = SYS_ID_AA64PFR0_EL1,
-		.field_pos = ID_AA64PFR0_GIC_SHIFT,
+		.field_pos = ID_AA64PFR0_EL1_GIC_SHIFT,
+		.field_width = 4,
 		.sign = FTR_UNSIGNED,
 		.min_field_value = 1,
 	},
@@ -1940,7 +2148,8 @@ static const struct arm64_cpu_capabilities arm64_features[] = {
 		.type = ARM64_CPUCAP_SYSTEM_FEATURE,
 		.matches = has_cpuid_feature,
 		.sys_reg = SYS_ID_AA64MMFR0_EL1,
-		.field_pos = ID_AA64MMFR0_ECV_SHIFT,
+		.field_pos = ID_AA64MMFR0_EL1_ECV_SHIFT,
+		.field_width = 4,
 		.sign = FTR_UNSIGNED,
 		.min_field_value = 1,
 	},
@@ -1951,7 +2160,8 @@ static const struct arm64_cpu_capabilities arm64_features[] = {
 		.type = ARM64_CPUCAP_SYSTEM_FEATURE,
 		.matches = has_cpuid_feature,
 		.sys_reg = SYS_ID_AA64MMFR1_EL1,
-		.field_pos = ID_AA64MMFR1_PAN_SHIFT,
+		.field_pos = ID_AA64MMFR1_EL1_PAN_SHIFT,
+		.field_width = 4,
 		.sign = FTR_UNSIGNED,
 		.min_field_value = 1,
 		.cpu_enable = cpu_enable_pan,
@@ -1964,7 +2174,8 @@ static const struct arm64_cpu_capabilities arm64_features[] = {
 		.type = ARM64_CPUCAP_SYSTEM_FEATURE,
 		.matches = has_cpuid_feature,
 		.sys_reg = SYS_ID_AA64MMFR1_EL1,
-		.field_pos = ID_AA64MMFR1_PAN_SHIFT,
+		.field_pos = ID_AA64MMFR1_EL1_PAN_SHIFT,
+		.field_width = 4,
 		.sign = FTR_UNSIGNED,
 		.min_field_value = 3,
 	},
@@ -1976,7 +2187,8 @@ static const struct arm64_cpu_capabilities arm64_features[] = {
 		.type = ARM64_CPUCAP_SYSTEM_FEATURE,
 		.matches = has_cpuid_feature,
 		.sys_reg = SYS_ID_AA64ISAR0_EL1,
-		.field_pos = ID_AA64ISAR0_ATOMICS_SHIFT,
+		.field_pos = ID_AA64ISAR0_EL1_ATOMIC_SHIFT,
+		.field_width = 4,
 		.sign = FTR_UNSIGNED,
 		.min_field_value = 2,
 	},
@@ -2000,8 +2212,9 @@ static const struct arm64_cpu_capabilities arm64_features[] = {
 		.matches = has_32bit_el0,
 		.sys_reg = SYS_ID_AA64PFR0_EL1,
 		.sign = FTR_UNSIGNED,
-		.field_pos = ID_AA64PFR0_EL0_SHIFT,
-		.min_field_value = ID_AA64PFR0_ELx_32BIT_64BIT,
+		.field_pos = ID_AA64PFR0_EL1_EL0_SHIFT,
+		.field_width = 4,
+		.min_field_value = ID_AA64PFR0_EL1_ELx_32BIT_64BIT,
 	},
 #ifdef CONFIG_KVM
 	{
@@ -2011,8 +2224,9 @@ static const struct arm64_cpu_capabilities arm64_features[] = {
 		.matches = has_cpuid_feature,
 		.sys_reg = SYS_ID_AA64PFR0_EL1,
 		.sign = FTR_UNSIGNED,
-		.field_pos = ID_AA64PFR0_EL1_SHIFT,
-		.min_field_value = ID_AA64PFR0_ELx_32BIT_64BIT,
+		.field_pos = ID_AA64PFR0_EL1_EL1_SHIFT,
+		.field_width = 4,
+		.min_field_value = ID_AA64PFR0_EL1_ELx_32BIT_64BIT,
 	},
 	{
 		.desc = "Protected KVM",
@@ -2031,7 +2245,8 @@ static const struct arm64_cpu_capabilities arm64_features[] = {
 		 * more details.
 		 */
 		.sys_reg = SYS_ID_AA64PFR0_EL1,
-		.field_pos = ID_AA64PFR0_CSV3_SHIFT,
+		.field_pos = ID_AA64PFR0_EL1_CSV3_SHIFT,
+		.field_width = 4,
 		.min_field_value = 1,
 		.matches = unmap_kernel_at_el0,
 		.cpu_enable = kpti_install_ng_mappings,
@@ -2050,7 +2265,8 @@ static const struct arm64_cpu_capabilities arm64_features[] = {
 		.type = ARM64_CPUCAP_SYSTEM_FEATURE,
 		.matches = has_cpuid_feature,
 		.sys_reg = SYS_ID_AA64ISAR1_EL1,
-		.field_pos = ID_AA64ISAR1_DPB_SHIFT,
+		.field_pos = ID_AA64ISAR1_EL1_DPB_SHIFT,
+		.field_width = 4,
 		.min_field_value = 1,
 	},
 	{
@@ -2060,7 +2276,8 @@ static const struct arm64_cpu_capabilities arm64_features[] = {
 		.matches = has_cpuid_feature,
 		.sys_reg = SYS_ID_AA64ISAR1_EL1,
 		.sign = FTR_UNSIGNED,
-		.field_pos = ID_AA64ISAR1_DPB_SHIFT,
+		.field_pos = ID_AA64ISAR1_EL1_DPB_SHIFT,
+		.field_width = 4,
 		.min_field_value = 2,
 	},
 #endif
@@ -2071,8 +2288,9 @@ static const struct arm64_cpu_capabilities arm64_features[] = {
 		.capability = ARM64_SVE,
 		.sys_reg = SYS_ID_AA64PFR0_EL1,
 		.sign = FTR_UNSIGNED,
-		.field_pos = ID_AA64PFR0_SVE_SHIFT,
-		.min_field_value = ID_AA64PFR0_SVE,
+		.field_pos = ID_AA64PFR0_EL1_SVE_SHIFT,
+		.field_width = 4,
+		.min_field_value = ID_AA64PFR0_EL1_SVE_IMP,
 		.matches = has_cpuid_feature,
 		.cpu_enable = sve_kernel_enable,
 	},
@@ -2085,8 +2303,9 @@ static const struct arm64_cpu_capabilities arm64_features[] = {
 		.matches = has_cpuid_feature,
 		.sys_reg = SYS_ID_AA64PFR0_EL1,
 		.sign = FTR_UNSIGNED,
-		.field_pos = ID_AA64PFR0_RAS_SHIFT,
-		.min_field_value = ID_AA64PFR0_RAS_V1,
+		.field_pos = ID_AA64PFR0_EL1_RAS_SHIFT,
+		.field_width = 4,
+		.min_field_value = ID_AA64PFR0_EL1_RAS_IMP,
 		.cpu_enable = cpu_clear_disr,
 	},
 #endif /* CONFIG_ARM64_RAS_EXTN */
@@ -2103,8 +2322,9 @@ static const struct arm64_cpu_capabilities arm64_features[] = {
 		.matches = has_amu,
 		.sys_reg = SYS_ID_AA64PFR0_EL1,
 		.sign = FTR_UNSIGNED,
-		.field_pos = ID_AA64PFR0_AMU_SHIFT,
-		.min_field_value = ID_AA64PFR0_AMU,
+		.field_pos = ID_AA64PFR0_EL1_AMU_SHIFT,
+		.field_width = 4,
+		.min_field_value = ID_AA64PFR0_EL1_AMU_IMP,
 		.cpu_enable = cpu_amu_enable,
 	},
 #endif /* CONFIG_ARM64_AMU_EXTN */
@@ -2127,10 +2347,10 @@ static const struct arm64_cpu_capabilities arm64_features[] = {
 		.capability = ARM64_HAS_STAGE2_FWB,
 		.sys_reg = SYS_ID_AA64MMFR2_EL1,
 		.sign = FTR_UNSIGNED,
-		.field_pos = ID_AA64MMFR2_FWB_SHIFT,
+		.field_pos = ID_AA64MMFR2_EL1_FWB_SHIFT,
+		.field_width = 4,
 		.min_field_value = 1,
 		.matches = has_cpuid_feature,
-		.cpu_enable = cpu_has_fwb,
 	},
 	{
 		.desc = "ARMv8.4 Translation Table Level",
@@ -2138,7 +2358,8 @@ static const struct arm64_cpu_capabilities arm64_features[] = {
 		.capability = ARM64_HAS_ARMv8_4_TTL,
 		.sys_reg = SYS_ID_AA64MMFR2_EL1,
 		.sign = FTR_UNSIGNED,
-		.field_pos = ID_AA64MMFR2_TTL_SHIFT,
+		.field_pos = ID_AA64MMFR2_EL1_TTL_SHIFT,
+		.field_width = 4,
 		.min_field_value = 1,
 		.matches = has_cpuid_feature,
 	},
@@ -2148,9 +2369,10 @@ static const struct arm64_cpu_capabilities arm64_features[] = {
 		.type = ARM64_CPUCAP_SYSTEM_FEATURE,
 		.matches = has_cpuid_feature,
 		.sys_reg = SYS_ID_AA64ISAR0_EL1,
-		.field_pos = ID_AA64ISAR0_TLB_SHIFT,
+		.field_pos = ID_AA64ISAR0_EL1_TLB_SHIFT,
+		.field_width = 4,
 		.sign = FTR_UNSIGNED,
-		.min_field_value = ID_AA64ISAR0_TLB_RANGE,
+		.min_field_value = ID_AA64ISAR0_EL1_TLB_RANGE,
 	},
 #ifdef CONFIG_ARM64_HW_AFDBM
 	{
@@ -2166,7 +2388,8 @@ static const struct arm64_cpu_capabilities arm64_features[] = {
 		.capability = ARM64_HW_DBM,
 		.sys_reg = SYS_ID_AA64MMFR1_EL1,
 		.sign = FTR_UNSIGNED,
-		.field_pos = ID_AA64MMFR1_HADBS_SHIFT,
+		.field_pos = ID_AA64MMFR1_EL1_HAFDBS_SHIFT,
+		.field_width = 4,
 		.min_field_value = 2,
 		.matches = has_hw_dbm,
 		.cpu_enable = cpu_enable_hw_dbm,
@@ -2178,7 +2401,8 @@ static const struct arm64_cpu_capabilities arm64_features[] = {
 		.type = ARM64_CPUCAP_SYSTEM_FEATURE,
 		.matches = has_cpuid_feature,
 		.sys_reg = SYS_ID_AA64ISAR0_EL1,
-		.field_pos = ID_AA64ISAR0_CRC32_SHIFT,
+		.field_pos = ID_AA64ISAR0_EL1_CRC32_SHIFT,
+		.field_width = 4,
 		.min_field_value = 1,
 	},
 	{
@@ -2187,9 +2411,10 @@ static const struct arm64_cpu_capabilities arm64_features[] = {
 		.type = ARM64_CPUCAP_SYSTEM_FEATURE,
 		.matches = has_cpuid_feature,
 		.sys_reg = SYS_ID_AA64PFR1_EL1,
-		.field_pos = ID_AA64PFR1_SSBS_SHIFT,
+		.field_pos = ID_AA64PFR1_EL1_SSBS_SHIFT,
+		.field_width = 4,
 		.sign = FTR_UNSIGNED,
-		.min_field_value = ID_AA64PFR1_SSBS_PSTATE_ONLY,
+		.min_field_value = ID_AA64PFR1_EL1_SSBS_IMP,
 	},
 #ifdef CONFIG_ARM64_CNP
 	{
@@ -2199,7 +2424,8 @@ static const struct arm64_cpu_capabilities arm64_features[] = {
 		.matches = has_useable_cnp,
 		.sys_reg = SYS_ID_AA64MMFR2_EL1,
 		.sign = FTR_UNSIGNED,
-		.field_pos = ID_AA64MMFR2_CNP_SHIFT,
+		.field_pos = ID_AA64MMFR2_EL1_CnP_SHIFT,
+		.field_width = 4,
 		.min_field_value = 1,
 		.cpu_enable = cpu_enable_cnp,
 	},
@@ -2210,19 +2436,32 @@ static const struct arm64_cpu_capabilities arm64_features[] = {
 		.type = ARM64_CPUCAP_SYSTEM_FEATURE,
 		.matches = has_cpuid_feature,
 		.sys_reg = SYS_ID_AA64ISAR1_EL1,
-		.field_pos = ID_AA64ISAR1_SB_SHIFT,
+		.field_pos = ID_AA64ISAR1_EL1_SB_SHIFT,
+		.field_width = 4,
 		.sign = FTR_UNSIGNED,
 		.min_field_value = 1,
 	},
 #ifdef CONFIG_ARM64_PTR_AUTH
 	{
-		.desc = "Address authentication (architected algorithm)",
-		.capability = ARM64_HAS_ADDRESS_AUTH_ARCH,
+		.desc = "Address authentication (architected QARMA5 algorithm)",
+		.capability = ARM64_HAS_ADDRESS_AUTH_ARCH_QARMA5,
 		.type = ARM64_CPUCAP_BOOT_CPU_FEATURE,
 		.sys_reg = SYS_ID_AA64ISAR1_EL1,
 		.sign = FTR_UNSIGNED,
-		.field_pos = ID_AA64ISAR1_APA_SHIFT,
-		.min_field_value = ID_AA64ISAR1_APA_ARCHITECTED,
+		.field_pos = ID_AA64ISAR1_EL1_APA_SHIFT,
+		.field_width = 4,
+		.min_field_value = ID_AA64ISAR1_EL1_APA_PAuth,
+		.matches = has_address_auth_cpucap,
+	},
+	{
+		.desc = "Address authentication (architected QARMA3 algorithm)",
+		.capability = ARM64_HAS_ADDRESS_AUTH_ARCH_QARMA3,
+		.type = ARM64_CPUCAP_BOOT_CPU_FEATURE,
+		.sys_reg = SYS_ID_AA64ISAR2_EL1,
+		.sign = FTR_UNSIGNED,
+		.field_pos = ID_AA64ISAR2_EL1_APA3_SHIFT,
+		.field_width = 4,
+		.min_field_value = ID_AA64ISAR2_EL1_APA3_PAuth,
 		.matches = has_address_auth_cpucap,
 	},
 	{
@@ -2231,8 +2470,9 @@ static const struct arm64_cpu_capabilities arm64_features[] = {
 		.type = ARM64_CPUCAP_BOOT_CPU_FEATURE,
 		.sys_reg = SYS_ID_AA64ISAR1_EL1,
 		.sign = FTR_UNSIGNED,
-		.field_pos = ID_AA64ISAR1_API_SHIFT,
-		.min_field_value = ID_AA64ISAR1_API_IMP_DEF,
+		.field_pos = ID_AA64ISAR1_EL1_API_SHIFT,
+		.field_width = 4,
+		.min_field_value = ID_AA64ISAR1_EL1_API_PAuth,
 		.matches = has_address_auth_cpucap,
 	},
 	{
@@ -2241,13 +2481,25 @@ static const struct arm64_cpu_capabilities arm64_features[] = {
 		.matches = has_address_auth_metacap,
 	},
 	{
-		.desc = "Generic authentication (architected algorithm)",
-		.capability = ARM64_HAS_GENERIC_AUTH_ARCH,
+		.desc = "Generic authentication (architected QARMA5 algorithm)",
+		.capability = ARM64_HAS_GENERIC_AUTH_ARCH_QARMA5,
 		.type = ARM64_CPUCAP_SYSTEM_FEATURE,
 		.sys_reg = SYS_ID_AA64ISAR1_EL1,
 		.sign = FTR_UNSIGNED,
-		.field_pos = ID_AA64ISAR1_GPA_SHIFT,
-		.min_field_value = ID_AA64ISAR1_GPA_ARCHITECTED,
+		.field_pos = ID_AA64ISAR1_EL1_GPA_SHIFT,
+		.field_width = 4,
+		.min_field_value = ID_AA64ISAR1_EL1_GPA_IMP,
+		.matches = has_cpuid_feature,
+	},
+	{
+		.desc = "Generic authentication (architected QARMA3 algorithm)",
+		.capability = ARM64_HAS_GENERIC_AUTH_ARCH_QARMA3,
+		.type = ARM64_CPUCAP_SYSTEM_FEATURE,
+		.sys_reg = SYS_ID_AA64ISAR2_EL1,
+		.sign = FTR_UNSIGNED,
+		.field_pos = ID_AA64ISAR2_EL1_GPA3_SHIFT,
+		.field_width = 4,
+		.min_field_value = ID_AA64ISAR2_EL1_GPA3_IMP,
 		.matches = has_cpuid_feature,
 	},
 	{
@@ -2256,8 +2508,9 @@ static const struct arm64_cpu_capabilities arm64_features[] = {
 		.type = ARM64_CPUCAP_SYSTEM_FEATURE,
 		.sys_reg = SYS_ID_AA64ISAR1_EL1,
 		.sign = FTR_UNSIGNED,
-		.field_pos = ID_AA64ISAR1_GPI_SHIFT,
-		.min_field_value = ID_AA64ISAR1_GPI_IMP_DEF,
+		.field_pos = ID_AA64ISAR1_EL1_GPI_SHIFT,
+		.field_width = 4,
+		.min_field_value = ID_AA64ISAR1_EL1_GPI_IMP,
 		.matches = has_cpuid_feature,
 	},
 	{
@@ -2276,7 +2529,8 @@ static const struct arm64_cpu_capabilities arm64_features[] = {
 		.type = ARM64_CPUCAP_STRICT_BOOT_CPU_FEATURE,
 		.matches = can_use_gic_priorities,
 		.sys_reg = SYS_ID_AA64PFR0_EL1,
-		.field_pos = ID_AA64PFR0_GIC_SHIFT,
+		.field_pos = ID_AA64PFR0_EL1_GIC_SHIFT,
+		.field_width = 4,
 		.sign = FTR_UNSIGNED,
 		.min_field_value = 1,
 	},
@@ -2288,24 +2542,24 @@ static const struct arm64_cpu_capabilities arm64_features[] = {
 		.type = ARM64_CPUCAP_SYSTEM_FEATURE,
 		.sys_reg = SYS_ID_AA64MMFR2_EL1,
 		.sign = FTR_UNSIGNED,
-		.field_pos = ID_AA64MMFR2_E0PD_SHIFT,
+		.field_width = 4,
+		.field_pos = ID_AA64MMFR2_EL1_E0PD_SHIFT,
 		.matches = has_cpuid_feature,
 		.min_field_value = 1,
 		.cpu_enable = cpu_enable_e0pd,
 	},
 #endif
-#ifdef CONFIG_ARCH_RANDOM
 	{
 		.desc = "Random Number Generator",
 		.capability = ARM64_HAS_RNG,
 		.type = ARM64_CPUCAP_SYSTEM_FEATURE,
 		.matches = has_cpuid_feature,
 		.sys_reg = SYS_ID_AA64ISAR0_EL1,
-		.field_pos = ID_AA64ISAR0_RNDR_SHIFT,
+		.field_pos = ID_AA64ISAR0_EL1_RNDR_SHIFT,
+		.field_width = 4,
 		.sign = FTR_UNSIGNED,
 		.min_field_value = 1,
 	},
-#endif
 #ifdef CONFIG_ARM64_BTI
 	{
 		.desc = "Branch Target Identification",
@@ -2318,8 +2572,9 @@ static const struct arm64_cpu_capabilities arm64_features[] = {
 		.matches = has_cpuid_feature,
 		.cpu_enable = bti_enable,
 		.sys_reg = SYS_ID_AA64PFR1_EL1,
-		.field_pos = ID_AA64PFR1_BT_SHIFT,
-		.min_field_value = ID_AA64PFR1_BT_BTI,
+		.field_pos = ID_AA64PFR1_EL1_BT_SHIFT,
+		.field_width = 4,
+		.min_field_value = ID_AA64PFR1_EL1_BT_IMP,
 		.sign = FTR_UNSIGNED,
 	},
 #endif
@@ -2330,8 +2585,9 @@ static const struct arm64_cpu_capabilities arm64_features[] = {
 		.type = ARM64_CPUCAP_STRICT_BOOT_CPU_FEATURE,
 		.matches = has_cpuid_feature,
 		.sys_reg = SYS_ID_AA64PFR1_EL1,
-		.field_pos = ID_AA64PFR1_MTE_SHIFT,
-		.min_field_value = ID_AA64PFR1_MTE,
+		.field_pos = ID_AA64PFR1_EL1_MTE_SHIFT,
+		.field_width = 4,
+		.min_field_value = ID_AA64PFR1_EL1_MTE_MTE2,
 		.sign = FTR_UNSIGNED,
 		.cpu_enable = cpu_enable_mte,
 	},
@@ -2341,8 +2597,9 @@ static const struct arm64_cpu_capabilities arm64_features[] = {
 		.type = ARM64_CPUCAP_BOOT_CPU_FEATURE,
 		.matches = has_cpuid_feature,
 		.sys_reg = SYS_ID_AA64PFR1_EL1,
-		.field_pos = ID_AA64PFR1_MTE_SHIFT,
-		.min_field_value = ID_AA64PFR1_MTE_ASYMM,
+		.field_pos = ID_AA64PFR1_EL1_MTE_SHIFT,
+		.field_width = 4,
+		.min_field_value = ID_AA64PFR1_EL1_MTE_MTE3,
 		.sign = FTR_UNSIGNED,
 	},
 #endif /* CONFIG_ARM64_MTE */
@@ -2352,17 +2609,69 @@ static const struct arm64_cpu_capabilities arm64_features[] = {
 		.type = ARM64_CPUCAP_SYSTEM_FEATURE,
 		.sys_reg = SYS_ID_AA64ISAR1_EL1,
 		.sign = FTR_UNSIGNED,
-		.field_pos = ID_AA64ISAR1_LRCPC_SHIFT,
+		.field_pos = ID_AA64ISAR1_EL1_LRCPC_SHIFT,
+		.field_width = 4,
 		.matches = has_cpuid_feature,
 		.min_field_value = 1,
 	},
+#ifdef CONFIG_ARM64_SME
+	{
+		.desc = "Scalable Matrix Extension",
+		.type = ARM64_CPUCAP_SYSTEM_FEATURE,
+		.capability = ARM64_SME,
+		.sys_reg = SYS_ID_AA64PFR1_EL1,
+		.sign = FTR_UNSIGNED,
+		.field_pos = ID_AA64PFR1_EL1_SME_SHIFT,
+		.field_width = 4,
+		.min_field_value = ID_AA64PFR1_EL1_SME_IMP,
+		.matches = has_cpuid_feature,
+		.cpu_enable = sme_kernel_enable,
+	},
+	/* FA64 should be sorted after the base SME capability */
+	{
+		.desc = "FA64",
+		.type = ARM64_CPUCAP_SYSTEM_FEATURE,
+		.capability = ARM64_SME_FA64,
+		.sys_reg = SYS_ID_AA64SMFR0_EL1,
+		.sign = FTR_UNSIGNED,
+		.field_pos = ID_AA64SMFR0_EL1_FA64_SHIFT,
+		.field_width = 1,
+		.min_field_value = ID_AA64SMFR0_EL1_FA64_IMP,
+		.matches = has_cpuid_feature,
+		.cpu_enable = fa64_kernel_enable,
+	},
+#endif /* CONFIG_ARM64_SME */
+	{
+		.desc = "WFx with timeout",
+		.capability = ARM64_HAS_WFXT,
+		.type = ARM64_CPUCAP_SYSTEM_FEATURE,
+		.sys_reg = SYS_ID_AA64ISAR2_EL1,
+		.sign = FTR_UNSIGNED,
+		.field_pos = ID_AA64ISAR2_EL1_WFxT_SHIFT,
+		.field_width = 4,
+		.matches = has_cpuid_feature,
+		.min_field_value = ID_AA64ISAR2_EL1_WFxT_IMP,
+	},
+	{
+		.desc = "Trap EL0 IMPLEMENTATION DEFINED functionality",
+		.capability = ARM64_HAS_TIDCP1,
+		.type = ARM64_CPUCAP_SYSTEM_FEATURE,
+		.sys_reg = SYS_ID_AA64MMFR1_EL1,
+		.sign = FTR_UNSIGNED,
+		.field_pos = ID_AA64MMFR1_EL1_TIDCP1_SHIFT,
+		.field_width = 4,
+		.min_field_value = ID_AA64MMFR1_EL1_TIDCP1_IMP,
+		.matches = has_cpuid_feature,
+		.cpu_enable = cpu_trap_el0_impdef,
+	},
 	{},
 };
 
-#define HWCAP_CPUID_MATCH(reg, field, s, min_value)				\
-		.matches = has_cpuid_feature,					\
+#define HWCAP_CPUID_MATCH(reg, field, width, s, min_value)			\
+		.matches = has_user_cpuid_feature,					\
 		.sys_reg = reg,							\
 		.field_pos = field,						\
+		.field_width = width,						\
 		.sign = s,							\
 		.min_field_value = min_value,
 
@@ -2372,10 +2681,10 @@ static const struct arm64_cpu_capabilities arm64_features[] = {
 		.hwcap_type = cap_type,						\
 		.hwcap = cap,							\
 
-#define HWCAP_CAP(reg, field, s, min_value, cap_type, cap)			\
+#define HWCAP_CAP(reg, field, width, s, min_value, cap_type, cap)		\
 	{									\
 		__HWCAP_CAP(#cap, cap_type, cap)				\
-		HWCAP_CPUID_MATCH(reg, field, s, min_value)			\
+		HWCAP_CPUID_MATCH(reg, field, width, s, min_value) 		\
 	}
 
 #define HWCAP_MULTI_CAP(list, cap_type, cap)					\
@@ -2394,88 +2703,113 @@ static const struct arm64_cpu_capabilities arm64_features[] = {
 #ifdef CONFIG_ARM64_PTR_AUTH
 static const struct arm64_cpu_capabilities ptr_auth_hwcap_addr_matches[] = {
 	{
-		HWCAP_CPUID_MATCH(SYS_ID_AA64ISAR1_EL1, ID_AA64ISAR1_APA_SHIFT,
-				  FTR_UNSIGNED, ID_AA64ISAR1_APA_ARCHITECTED)
+		HWCAP_CPUID_MATCH(SYS_ID_AA64ISAR1_EL1, ID_AA64ISAR1_EL1_APA_SHIFT,
+				  4, FTR_UNSIGNED,
+				  ID_AA64ISAR1_EL1_APA_PAuth)
+	},
+	{
+		HWCAP_CPUID_MATCH(SYS_ID_AA64ISAR2_EL1, ID_AA64ISAR2_EL1_APA3_SHIFT,
+				  4, FTR_UNSIGNED, ID_AA64ISAR2_EL1_APA3_PAuth)
 	},
 	{
-		HWCAP_CPUID_MATCH(SYS_ID_AA64ISAR1_EL1, ID_AA64ISAR1_API_SHIFT,
-				  FTR_UNSIGNED, ID_AA64ISAR1_API_IMP_DEF)
+		HWCAP_CPUID_MATCH(SYS_ID_AA64ISAR1_EL1, ID_AA64ISAR1_EL1_API_SHIFT,
+				  4, FTR_UNSIGNED, ID_AA64ISAR1_EL1_API_PAuth)
 	},
 	{},
 };
 
 static const struct arm64_cpu_capabilities ptr_auth_hwcap_gen_matches[] = {
 	{
-		HWCAP_CPUID_MATCH(SYS_ID_AA64ISAR1_EL1, ID_AA64ISAR1_GPA_SHIFT,
-				  FTR_UNSIGNED, ID_AA64ISAR1_GPA_ARCHITECTED)
+		HWCAP_CPUID_MATCH(SYS_ID_AA64ISAR1_EL1, ID_AA64ISAR1_EL1_GPA_SHIFT,
+				  4, FTR_UNSIGNED, ID_AA64ISAR1_EL1_GPA_IMP)
+	},
+	{
+		HWCAP_CPUID_MATCH(SYS_ID_AA64ISAR2_EL1, ID_AA64ISAR2_EL1_GPA3_SHIFT,
+				  4, FTR_UNSIGNED, ID_AA64ISAR2_EL1_GPA3_IMP)
 	},
 	{
-		HWCAP_CPUID_MATCH(SYS_ID_AA64ISAR1_EL1, ID_AA64ISAR1_GPI_SHIFT,
-				  FTR_UNSIGNED, ID_AA64ISAR1_GPI_IMP_DEF)
+		HWCAP_CPUID_MATCH(SYS_ID_AA64ISAR1_EL1, ID_AA64ISAR1_EL1_GPI_SHIFT,
+				  4, FTR_UNSIGNED, ID_AA64ISAR1_EL1_GPI_IMP)
 	},
 	{},
 };
 #endif
 
 static const struct arm64_cpu_capabilities arm64_elf_hwcaps[] = {
-	HWCAP_CAP(SYS_ID_AA64ISAR0_EL1, ID_AA64ISAR0_AES_SHIFT, FTR_UNSIGNED, 2, CAP_HWCAP, KERNEL_HWCAP_PMULL),
-	HWCAP_CAP(SYS_ID_AA64ISAR0_EL1, ID_AA64ISAR0_AES_SHIFT, FTR_UNSIGNED, 1, CAP_HWCAP, KERNEL_HWCAP_AES),
-	HWCAP_CAP(SYS_ID_AA64ISAR0_EL1, ID_AA64ISAR0_SHA1_SHIFT, FTR_UNSIGNED, 1, CAP_HWCAP, KERNEL_HWCAP_SHA1),
-	HWCAP_CAP(SYS_ID_AA64ISAR0_EL1, ID_AA64ISAR0_SHA2_SHIFT, FTR_UNSIGNED, 1, CAP_HWCAP, KERNEL_HWCAP_SHA2),
-	HWCAP_CAP(SYS_ID_AA64ISAR0_EL1, ID_AA64ISAR0_SHA2_SHIFT, FTR_UNSIGNED, 2, CAP_HWCAP, KERNEL_HWCAP_SHA512),
-	HWCAP_CAP(SYS_ID_AA64ISAR0_EL1, ID_AA64ISAR0_CRC32_SHIFT, FTR_UNSIGNED, 1, CAP_HWCAP, KERNEL_HWCAP_CRC32),
-	HWCAP_CAP(SYS_ID_AA64ISAR0_EL1, ID_AA64ISAR0_ATOMICS_SHIFT, FTR_UNSIGNED, 2, CAP_HWCAP, KERNEL_HWCAP_ATOMICS),
-	HWCAP_CAP(SYS_ID_AA64ISAR0_EL1, ID_AA64ISAR0_RDM_SHIFT, FTR_UNSIGNED, 1, CAP_HWCAP, KERNEL_HWCAP_ASIMDRDM),
-	HWCAP_CAP(SYS_ID_AA64ISAR0_EL1, ID_AA64ISAR0_SHA3_SHIFT, FTR_UNSIGNED, 1, CAP_HWCAP, KERNEL_HWCAP_SHA3),
-	HWCAP_CAP(SYS_ID_AA64ISAR0_EL1, ID_AA64ISAR0_SM3_SHIFT, FTR_UNSIGNED, 1, CAP_HWCAP, KERNEL_HWCAP_SM3),
-	HWCAP_CAP(SYS_ID_AA64ISAR0_EL1, ID_AA64ISAR0_SM4_SHIFT, FTR_UNSIGNED, 1, CAP_HWCAP, KERNEL_HWCAP_SM4),
-	HWCAP_CAP(SYS_ID_AA64ISAR0_EL1, ID_AA64ISAR0_DP_SHIFT, FTR_UNSIGNED, 1, CAP_HWCAP, KERNEL_HWCAP_ASIMDDP),
-	HWCAP_CAP(SYS_ID_AA64ISAR0_EL1, ID_AA64ISAR0_FHM_SHIFT, FTR_UNSIGNED, 1, CAP_HWCAP, KERNEL_HWCAP_ASIMDFHM),
-	HWCAP_CAP(SYS_ID_AA64ISAR0_EL1, ID_AA64ISAR0_TS_SHIFT, FTR_UNSIGNED, 1, CAP_HWCAP, KERNEL_HWCAP_FLAGM),
-	HWCAP_CAP(SYS_ID_AA64ISAR0_EL1, ID_AA64ISAR0_TS_SHIFT, FTR_UNSIGNED, 2, CAP_HWCAP, KERNEL_HWCAP_FLAGM2),
-	HWCAP_CAP(SYS_ID_AA64ISAR0_EL1, ID_AA64ISAR0_RNDR_SHIFT, FTR_UNSIGNED, 1, CAP_HWCAP, KERNEL_HWCAP_RNG),
-	HWCAP_CAP(SYS_ID_AA64PFR0_EL1, ID_AA64PFR0_FP_SHIFT, FTR_SIGNED, 0, CAP_HWCAP, KERNEL_HWCAP_FP),
-	HWCAP_CAP(SYS_ID_AA64PFR0_EL1, ID_AA64PFR0_FP_SHIFT, FTR_SIGNED, 1, CAP_HWCAP, KERNEL_HWCAP_FPHP),
-	HWCAP_CAP(SYS_ID_AA64PFR0_EL1, ID_AA64PFR0_ASIMD_SHIFT, FTR_SIGNED, 0, CAP_HWCAP, KERNEL_HWCAP_ASIMD),
-	HWCAP_CAP(SYS_ID_AA64PFR0_EL1, ID_AA64PFR0_ASIMD_SHIFT, FTR_SIGNED, 1, CAP_HWCAP, KERNEL_HWCAP_ASIMDHP),
-	HWCAP_CAP(SYS_ID_AA64PFR0_EL1, ID_AA64PFR0_DIT_SHIFT, FTR_SIGNED, 1, CAP_HWCAP, KERNEL_HWCAP_DIT),
-	HWCAP_CAP(SYS_ID_AA64ISAR1_EL1, ID_AA64ISAR1_DPB_SHIFT, FTR_UNSIGNED, 1, CAP_HWCAP, KERNEL_HWCAP_DCPOP),
-	HWCAP_CAP(SYS_ID_AA64ISAR1_EL1, ID_AA64ISAR1_DPB_SHIFT, FTR_UNSIGNED, 2, CAP_HWCAP, KERNEL_HWCAP_DCPODP),
-	HWCAP_CAP(SYS_ID_AA64ISAR1_EL1, ID_AA64ISAR1_JSCVT_SHIFT, FTR_UNSIGNED, 1, CAP_HWCAP, KERNEL_HWCAP_JSCVT),
-	HWCAP_CAP(SYS_ID_AA64ISAR1_EL1, ID_AA64ISAR1_FCMA_SHIFT, FTR_UNSIGNED, 1, CAP_HWCAP, KERNEL_HWCAP_FCMA),
-	HWCAP_CAP(SYS_ID_AA64ISAR1_EL1, ID_AA64ISAR1_LRCPC_SHIFT, FTR_UNSIGNED, 1, CAP_HWCAP, KERNEL_HWCAP_LRCPC),
-	HWCAP_CAP(SYS_ID_AA64ISAR1_EL1, ID_AA64ISAR1_LRCPC_SHIFT, FTR_UNSIGNED, 2, CAP_HWCAP, KERNEL_HWCAP_ILRCPC),
-	HWCAP_CAP(SYS_ID_AA64ISAR1_EL1, ID_AA64ISAR1_FRINTTS_SHIFT, FTR_UNSIGNED, 1, CAP_HWCAP, KERNEL_HWCAP_FRINT),
-	HWCAP_CAP(SYS_ID_AA64ISAR1_EL1, ID_AA64ISAR1_SB_SHIFT, FTR_UNSIGNED, 1, CAP_HWCAP, KERNEL_HWCAP_SB),
-	HWCAP_CAP(SYS_ID_AA64ISAR1_EL1, ID_AA64ISAR1_BF16_SHIFT, FTR_UNSIGNED, 1, CAP_HWCAP, KERNEL_HWCAP_BF16),
-	HWCAP_CAP(SYS_ID_AA64ISAR1_EL1, ID_AA64ISAR1_DGH_SHIFT, FTR_UNSIGNED, 1, CAP_HWCAP, KERNEL_HWCAP_DGH),
-	HWCAP_CAP(SYS_ID_AA64ISAR1_EL1, ID_AA64ISAR1_I8MM_SHIFT, FTR_UNSIGNED, 1, CAP_HWCAP, KERNEL_HWCAP_I8MM),
-	HWCAP_CAP(SYS_ID_AA64MMFR2_EL1, ID_AA64MMFR2_AT_SHIFT, FTR_UNSIGNED, 1, CAP_HWCAP, KERNEL_HWCAP_USCAT),
+	HWCAP_CAP(SYS_ID_AA64ISAR0_EL1, ID_AA64ISAR0_EL1_AES_SHIFT, 4, FTR_UNSIGNED, 2, CAP_HWCAP, KERNEL_HWCAP_PMULL),
+	HWCAP_CAP(SYS_ID_AA64ISAR0_EL1, ID_AA64ISAR0_EL1_AES_SHIFT, 4, FTR_UNSIGNED, 1, CAP_HWCAP, KERNEL_HWCAP_AES),
+	HWCAP_CAP(SYS_ID_AA64ISAR0_EL1, ID_AA64ISAR0_EL1_SHA1_SHIFT, 4, FTR_UNSIGNED, 1, CAP_HWCAP, KERNEL_HWCAP_SHA1),
+	HWCAP_CAP(SYS_ID_AA64ISAR0_EL1, ID_AA64ISAR0_EL1_SHA2_SHIFT, 4, FTR_UNSIGNED, 1, CAP_HWCAP, KERNEL_HWCAP_SHA2),
+	HWCAP_CAP(SYS_ID_AA64ISAR0_EL1, ID_AA64ISAR0_EL1_SHA2_SHIFT, 4, FTR_UNSIGNED, 2, CAP_HWCAP, KERNEL_HWCAP_SHA512),
+	HWCAP_CAP(SYS_ID_AA64ISAR0_EL1, ID_AA64ISAR0_EL1_CRC32_SHIFT, 4, FTR_UNSIGNED, 1, CAP_HWCAP, KERNEL_HWCAP_CRC32),
+	HWCAP_CAP(SYS_ID_AA64ISAR0_EL1, ID_AA64ISAR0_EL1_ATOMIC_SHIFT, 4, FTR_UNSIGNED, 2, CAP_HWCAP, KERNEL_HWCAP_ATOMICS),
+	HWCAP_CAP(SYS_ID_AA64ISAR0_EL1, ID_AA64ISAR0_EL1_RDM_SHIFT, 4, FTR_UNSIGNED, 1, CAP_HWCAP, KERNEL_HWCAP_ASIMDRDM),
+	HWCAP_CAP(SYS_ID_AA64ISAR0_EL1, ID_AA64ISAR0_EL1_SHA3_SHIFT, 4, FTR_UNSIGNED, 1, CAP_HWCAP, KERNEL_HWCAP_SHA3),
+	HWCAP_CAP(SYS_ID_AA64ISAR0_EL1, ID_AA64ISAR0_EL1_SM3_SHIFT, 4, FTR_UNSIGNED, 1, CAP_HWCAP, KERNEL_HWCAP_SM3),
+	HWCAP_CAP(SYS_ID_AA64ISAR0_EL1, ID_AA64ISAR0_EL1_SM4_SHIFT, 4, FTR_UNSIGNED, 1, CAP_HWCAP, KERNEL_HWCAP_SM4),
+	HWCAP_CAP(SYS_ID_AA64ISAR0_EL1, ID_AA64ISAR0_EL1_DP_SHIFT, 4, FTR_UNSIGNED, 1, CAP_HWCAP, KERNEL_HWCAP_ASIMDDP),
+	HWCAP_CAP(SYS_ID_AA64ISAR0_EL1, ID_AA64ISAR0_EL1_FHM_SHIFT, 4, FTR_UNSIGNED, 1, CAP_HWCAP, KERNEL_HWCAP_ASIMDFHM),
+	HWCAP_CAP(SYS_ID_AA64ISAR0_EL1, ID_AA64ISAR0_EL1_TS_SHIFT, 4, FTR_UNSIGNED, 1, CAP_HWCAP, KERNEL_HWCAP_FLAGM),
+	HWCAP_CAP(SYS_ID_AA64ISAR0_EL1, ID_AA64ISAR0_EL1_TS_SHIFT, 4, FTR_UNSIGNED, 2, CAP_HWCAP, KERNEL_HWCAP_FLAGM2),
+	HWCAP_CAP(SYS_ID_AA64ISAR0_EL1, ID_AA64ISAR0_EL1_RNDR_SHIFT, 4, FTR_UNSIGNED, 1, CAP_HWCAP, KERNEL_HWCAP_RNG),
+	HWCAP_CAP(SYS_ID_AA64PFR0_EL1, ID_AA64PFR0_EL1_FP_SHIFT, 4, FTR_SIGNED, 0, CAP_HWCAP, KERNEL_HWCAP_FP),
+	HWCAP_CAP(SYS_ID_AA64PFR0_EL1, ID_AA64PFR0_EL1_FP_SHIFT, 4, FTR_SIGNED, 1, CAP_HWCAP, KERNEL_HWCAP_FPHP),
+	HWCAP_CAP(SYS_ID_AA64PFR0_EL1, ID_AA64PFR0_EL1_AdvSIMD_SHIFT, 4, FTR_SIGNED, 0, CAP_HWCAP, KERNEL_HWCAP_ASIMD),
+	HWCAP_CAP(SYS_ID_AA64PFR0_EL1, ID_AA64PFR0_EL1_AdvSIMD_SHIFT, 4, FTR_SIGNED, 1, CAP_HWCAP, KERNEL_HWCAP_ASIMDHP),
+	HWCAP_CAP(SYS_ID_AA64PFR0_EL1, ID_AA64PFR0_EL1_DIT_SHIFT, 4, FTR_SIGNED, 1, CAP_HWCAP, KERNEL_HWCAP_DIT),
+	HWCAP_CAP(SYS_ID_AA64ISAR1_EL1, ID_AA64ISAR1_EL1_DPB_SHIFT, 4, FTR_UNSIGNED, 1, CAP_HWCAP, KERNEL_HWCAP_DCPOP),
+	HWCAP_CAP(SYS_ID_AA64ISAR1_EL1, ID_AA64ISAR1_EL1_DPB_SHIFT, 4, FTR_UNSIGNED, 2, CAP_HWCAP, KERNEL_HWCAP_DCPODP),
+	HWCAP_CAP(SYS_ID_AA64ISAR1_EL1, ID_AA64ISAR1_EL1_JSCVT_SHIFT, 4, FTR_UNSIGNED, 1, CAP_HWCAP, KERNEL_HWCAP_JSCVT),
+	HWCAP_CAP(SYS_ID_AA64ISAR1_EL1, ID_AA64ISAR1_EL1_FCMA_SHIFT, 4, FTR_UNSIGNED, 1, CAP_HWCAP, KERNEL_HWCAP_FCMA),
+	HWCAP_CAP(SYS_ID_AA64ISAR1_EL1, ID_AA64ISAR1_EL1_LRCPC_SHIFT, 4, FTR_UNSIGNED, 1, CAP_HWCAP, KERNEL_HWCAP_LRCPC),
+	HWCAP_CAP(SYS_ID_AA64ISAR1_EL1, ID_AA64ISAR1_EL1_LRCPC_SHIFT, 4, FTR_UNSIGNED, 2, CAP_HWCAP, KERNEL_HWCAP_ILRCPC),
+	HWCAP_CAP(SYS_ID_AA64ISAR1_EL1, ID_AA64ISAR1_EL1_FRINTTS_SHIFT, 4, FTR_UNSIGNED, 1, CAP_HWCAP, KERNEL_HWCAP_FRINT),
+	HWCAP_CAP(SYS_ID_AA64ISAR1_EL1, ID_AA64ISAR1_EL1_SB_SHIFT, 4, FTR_UNSIGNED, 1, CAP_HWCAP, KERNEL_HWCAP_SB),
+	HWCAP_CAP(SYS_ID_AA64ISAR1_EL1, ID_AA64ISAR1_EL1_BF16_SHIFT, 4, FTR_UNSIGNED, 1, CAP_HWCAP, KERNEL_HWCAP_BF16),
+	HWCAP_CAP(SYS_ID_AA64ISAR1_EL1, ID_AA64ISAR1_EL1_BF16_SHIFT, 4, FTR_UNSIGNED, 2, CAP_HWCAP, KERNEL_HWCAP_EBF16),
+	HWCAP_CAP(SYS_ID_AA64ISAR1_EL1, ID_AA64ISAR1_EL1_DGH_SHIFT, 4, FTR_UNSIGNED, 1, CAP_HWCAP, KERNEL_HWCAP_DGH),
+	HWCAP_CAP(SYS_ID_AA64ISAR1_EL1, ID_AA64ISAR1_EL1_I8MM_SHIFT, 4, FTR_UNSIGNED, 1, CAP_HWCAP, KERNEL_HWCAP_I8MM),
+	HWCAP_CAP(SYS_ID_AA64MMFR2_EL1, ID_AA64MMFR2_EL1_AT_SHIFT, 4, FTR_UNSIGNED, 1, CAP_HWCAP, KERNEL_HWCAP_USCAT),
 #ifdef CONFIG_ARM64_SVE
-	HWCAP_CAP(SYS_ID_AA64PFR0_EL1, ID_AA64PFR0_SVE_SHIFT, FTR_UNSIGNED, ID_AA64PFR0_SVE, CAP_HWCAP, KERNEL_HWCAP_SVE),
-	HWCAP_CAP(SYS_ID_AA64ZFR0_EL1, ID_AA64ZFR0_SVEVER_SHIFT, FTR_UNSIGNED, ID_AA64ZFR0_SVEVER_SVE2, CAP_HWCAP, KERNEL_HWCAP_SVE2),
-	HWCAP_CAP(SYS_ID_AA64ZFR0_EL1, ID_AA64ZFR0_AES_SHIFT, FTR_UNSIGNED, ID_AA64ZFR0_AES, CAP_HWCAP, KERNEL_HWCAP_SVEAES),
-	HWCAP_CAP(SYS_ID_AA64ZFR0_EL1, ID_AA64ZFR0_AES_SHIFT, FTR_UNSIGNED, ID_AA64ZFR0_AES_PMULL, CAP_HWCAP, KERNEL_HWCAP_SVEPMULL),
-	HWCAP_CAP(SYS_ID_AA64ZFR0_EL1, ID_AA64ZFR0_BITPERM_SHIFT, FTR_UNSIGNED, ID_AA64ZFR0_BITPERM, CAP_HWCAP, KERNEL_HWCAP_SVEBITPERM),
-	HWCAP_CAP(SYS_ID_AA64ZFR0_EL1, ID_AA64ZFR0_BF16_SHIFT, FTR_UNSIGNED, ID_AA64ZFR0_BF16, CAP_HWCAP, KERNEL_HWCAP_SVEBF16),
-	HWCAP_CAP(SYS_ID_AA64ZFR0_EL1, ID_AA64ZFR0_SHA3_SHIFT, FTR_UNSIGNED, ID_AA64ZFR0_SHA3, CAP_HWCAP, KERNEL_HWCAP_SVESHA3),
-	HWCAP_CAP(SYS_ID_AA64ZFR0_EL1, ID_AA64ZFR0_SM4_SHIFT, FTR_UNSIGNED, ID_AA64ZFR0_SM4, CAP_HWCAP, KERNEL_HWCAP_SVESM4),
-	HWCAP_CAP(SYS_ID_AA64ZFR0_EL1, ID_AA64ZFR0_I8MM_SHIFT, FTR_UNSIGNED, ID_AA64ZFR0_I8MM, CAP_HWCAP, KERNEL_HWCAP_SVEI8MM),
-	HWCAP_CAP(SYS_ID_AA64ZFR0_EL1, ID_AA64ZFR0_F32MM_SHIFT, FTR_UNSIGNED, ID_AA64ZFR0_F32MM, CAP_HWCAP, KERNEL_HWCAP_SVEF32MM),
-	HWCAP_CAP(SYS_ID_AA64ZFR0_EL1, ID_AA64ZFR0_F64MM_SHIFT, FTR_UNSIGNED, ID_AA64ZFR0_F64MM, CAP_HWCAP, KERNEL_HWCAP_SVEF64MM),
+	HWCAP_CAP(SYS_ID_AA64PFR0_EL1, ID_AA64PFR0_EL1_SVE_SHIFT, 4, FTR_UNSIGNED, ID_AA64PFR0_EL1_SVE_IMP, CAP_HWCAP, KERNEL_HWCAP_SVE),
+	HWCAP_CAP(SYS_ID_AA64ZFR0_EL1, ID_AA64ZFR0_EL1_SVEver_SHIFT, 4, FTR_UNSIGNED, ID_AA64ZFR0_EL1_SVEver_SVE2, CAP_HWCAP, KERNEL_HWCAP_SVE2),
+	HWCAP_CAP(SYS_ID_AA64ZFR0_EL1, ID_AA64ZFR0_EL1_AES_SHIFT, 4, FTR_UNSIGNED, ID_AA64ZFR0_EL1_AES_IMP, CAP_HWCAP, KERNEL_HWCAP_SVEAES),
+	HWCAP_CAP(SYS_ID_AA64ZFR0_EL1, ID_AA64ZFR0_EL1_AES_SHIFT, 4, FTR_UNSIGNED, ID_AA64ZFR0_EL1_AES_PMULL128, CAP_HWCAP, KERNEL_HWCAP_SVEPMULL),
+	HWCAP_CAP(SYS_ID_AA64ZFR0_EL1, ID_AA64ZFR0_EL1_BitPerm_SHIFT, 4, FTR_UNSIGNED, ID_AA64ZFR0_EL1_BitPerm_IMP, CAP_HWCAP, KERNEL_HWCAP_SVEBITPERM),
+	HWCAP_CAP(SYS_ID_AA64ZFR0_EL1, ID_AA64ZFR0_EL1_BF16_SHIFT, 4, FTR_UNSIGNED, ID_AA64ZFR0_EL1_BF16_IMP, CAP_HWCAP, KERNEL_HWCAP_SVEBF16),
+	HWCAP_CAP(SYS_ID_AA64ZFR0_EL1, ID_AA64ZFR0_EL1_BF16_SHIFT, 4, FTR_UNSIGNED, ID_AA64ZFR0_EL1_BF16_EBF16, CAP_HWCAP, KERNEL_HWCAP_SVE_EBF16),
+	HWCAP_CAP(SYS_ID_AA64ZFR0_EL1, ID_AA64ZFR0_EL1_SHA3_SHIFT, 4, FTR_UNSIGNED, ID_AA64ZFR0_EL1_SHA3_IMP, CAP_HWCAP, KERNEL_HWCAP_SVESHA3),
+	HWCAP_CAP(SYS_ID_AA64ZFR0_EL1, ID_AA64ZFR0_EL1_SM4_SHIFT, 4, FTR_UNSIGNED, ID_AA64ZFR0_EL1_SM4_IMP, CAP_HWCAP, KERNEL_HWCAP_SVESM4),
+	HWCAP_CAP(SYS_ID_AA64ZFR0_EL1, ID_AA64ZFR0_EL1_I8MM_SHIFT, 4, FTR_UNSIGNED, ID_AA64ZFR0_EL1_I8MM_IMP, CAP_HWCAP, KERNEL_HWCAP_SVEI8MM),
+	HWCAP_CAP(SYS_ID_AA64ZFR0_EL1, ID_AA64ZFR0_EL1_F32MM_SHIFT, 4, FTR_UNSIGNED, ID_AA64ZFR0_EL1_F32MM_IMP, CAP_HWCAP, KERNEL_HWCAP_SVEF32MM),
+	HWCAP_CAP(SYS_ID_AA64ZFR0_EL1, ID_AA64ZFR0_EL1_F64MM_SHIFT, 4, FTR_UNSIGNED, ID_AA64ZFR0_EL1_F64MM_IMP, CAP_HWCAP, KERNEL_HWCAP_SVEF64MM),
 #endif
-	HWCAP_CAP(SYS_ID_AA64PFR1_EL1, ID_AA64PFR1_SSBS_SHIFT, FTR_UNSIGNED, ID_AA64PFR1_SSBS_PSTATE_INSNS, CAP_HWCAP, KERNEL_HWCAP_SSBS),
+	HWCAP_CAP(SYS_ID_AA64PFR1_EL1, ID_AA64PFR1_EL1_SSBS_SHIFT, 4, FTR_UNSIGNED, ID_AA64PFR1_EL1_SSBS_SSBS2, CAP_HWCAP, KERNEL_HWCAP_SSBS),
 #ifdef CONFIG_ARM64_BTI
-	HWCAP_CAP(SYS_ID_AA64PFR1_EL1, ID_AA64PFR1_BT_SHIFT, FTR_UNSIGNED, ID_AA64PFR1_BT_BTI, CAP_HWCAP, KERNEL_HWCAP_BTI),
+	HWCAP_CAP(SYS_ID_AA64PFR1_EL1, ID_AA64PFR1_EL1_BT_SHIFT, 4, FTR_UNSIGNED, ID_AA64PFR1_EL1_BT_IMP, CAP_HWCAP, KERNEL_HWCAP_BTI),
 #endif
 #ifdef CONFIG_ARM64_PTR_AUTH
 	HWCAP_MULTI_CAP(ptr_auth_hwcap_addr_matches, CAP_HWCAP, KERNEL_HWCAP_PACA),
 	HWCAP_MULTI_CAP(ptr_auth_hwcap_gen_matches, CAP_HWCAP, KERNEL_HWCAP_PACG),
 #endif
 #ifdef CONFIG_ARM64_MTE
-	HWCAP_CAP(SYS_ID_AA64PFR1_EL1, ID_AA64PFR1_MTE_SHIFT, FTR_UNSIGNED, ID_AA64PFR1_MTE, CAP_HWCAP, KERNEL_HWCAP_MTE),
+	HWCAP_CAP(SYS_ID_AA64PFR1_EL1, ID_AA64PFR1_EL1_MTE_SHIFT, 4, FTR_UNSIGNED, ID_AA64PFR1_EL1_MTE_MTE2, CAP_HWCAP, KERNEL_HWCAP_MTE),
+	HWCAP_CAP(SYS_ID_AA64PFR1_EL1, ID_AA64PFR1_EL1_MTE_SHIFT, 4, FTR_UNSIGNED, ID_AA64PFR1_EL1_MTE_MTE3, CAP_HWCAP, KERNEL_HWCAP_MTE3),
 #endif /* CONFIG_ARM64_MTE */
-	HWCAP_CAP(SYS_ID_AA64MMFR0_EL1, ID_AA64MMFR0_ECV_SHIFT, FTR_UNSIGNED, 1, CAP_HWCAP, KERNEL_HWCAP_ECV),
+	HWCAP_CAP(SYS_ID_AA64MMFR0_EL1, ID_AA64MMFR0_EL1_ECV_SHIFT, 4, FTR_UNSIGNED, 1, CAP_HWCAP, KERNEL_HWCAP_ECV),
+	HWCAP_CAP(SYS_ID_AA64MMFR1_EL1, ID_AA64MMFR1_EL1_AFP_SHIFT, 4, FTR_UNSIGNED, 1, CAP_HWCAP, KERNEL_HWCAP_AFP),
+	HWCAP_CAP(SYS_ID_AA64ISAR2_EL1, ID_AA64ISAR2_EL1_RPRES_SHIFT, 4, FTR_UNSIGNED, 1, CAP_HWCAP, KERNEL_HWCAP_RPRES),
+	HWCAP_CAP(SYS_ID_AA64ISAR2_EL1, ID_AA64ISAR2_EL1_WFxT_SHIFT, 4, FTR_UNSIGNED, ID_AA64ISAR2_EL1_WFxT_IMP, CAP_HWCAP, KERNEL_HWCAP_WFXT),
+#ifdef CONFIG_ARM64_SME
+	HWCAP_CAP(SYS_ID_AA64PFR1_EL1, ID_AA64PFR1_EL1_SME_SHIFT, 4, FTR_UNSIGNED, ID_AA64PFR1_EL1_SME_IMP, CAP_HWCAP, KERNEL_HWCAP_SME),
+	HWCAP_CAP(SYS_ID_AA64SMFR0_EL1, ID_AA64SMFR0_EL1_FA64_SHIFT, 1, FTR_UNSIGNED, ID_AA64SMFR0_EL1_FA64_IMP, CAP_HWCAP, KERNEL_HWCAP_SME_FA64),
+	HWCAP_CAP(SYS_ID_AA64SMFR0_EL1, ID_AA64SMFR0_EL1_I16I64_SHIFT, 4, FTR_UNSIGNED, ID_AA64SMFR0_EL1_I16I64_IMP, CAP_HWCAP, KERNEL_HWCAP_SME_I16I64),
+	HWCAP_CAP(SYS_ID_AA64SMFR0_EL1, ID_AA64SMFR0_EL1_F64F64_SHIFT, 1, FTR_UNSIGNED, ID_AA64SMFR0_EL1_F64F64_IMP, CAP_HWCAP, KERNEL_HWCAP_SME_F64F64),
+	HWCAP_CAP(SYS_ID_AA64SMFR0_EL1, ID_AA64SMFR0_EL1_I8I32_SHIFT, 4, FTR_UNSIGNED, ID_AA64SMFR0_EL1_I8I32_IMP, CAP_HWCAP, KERNEL_HWCAP_SME_I8I32),
+	HWCAP_CAP(SYS_ID_AA64SMFR0_EL1, ID_AA64SMFR0_EL1_F16F32_SHIFT, 1, FTR_UNSIGNED, ID_AA64SMFR0_EL1_F16F32_IMP, CAP_HWCAP, KERNEL_HWCAP_SME_F16F32),
+	HWCAP_CAP(SYS_ID_AA64SMFR0_EL1, ID_AA64SMFR0_EL1_B16F32_SHIFT, 1, FTR_UNSIGNED, ID_AA64SMFR0_EL1_B16F32_IMP, CAP_HWCAP, KERNEL_HWCAP_SME_B16F32),
+	HWCAP_CAP(SYS_ID_AA64SMFR0_EL1, ID_AA64SMFR0_EL1_F32F32_SHIFT, 1, FTR_UNSIGNED, ID_AA64SMFR0_EL1_F32F32_IMP, CAP_HWCAP, KERNEL_HWCAP_SME_F32F32),
+#endif /* CONFIG_ARM64_SME */
 	{},
 };
 
@@ -2504,15 +2838,15 @@ static bool compat_has_neon(const struct arm64_cpu_capabilities *cap, int scope)
 static const struct arm64_cpu_capabilities compat_elf_hwcaps[] = {
 #ifdef CONFIG_COMPAT
 	HWCAP_CAP_MATCH(compat_has_neon, CAP_COMPAT_HWCAP, COMPAT_HWCAP_NEON),
-	HWCAP_CAP(SYS_MVFR1_EL1, MVFR1_SIMDFMAC_SHIFT, FTR_UNSIGNED, 1, CAP_COMPAT_HWCAP, COMPAT_HWCAP_VFPv4),
+	HWCAP_CAP(SYS_MVFR1_EL1, MVFR1_SIMDFMAC_SHIFT, 4, FTR_UNSIGNED, 1, CAP_COMPAT_HWCAP, COMPAT_HWCAP_VFPv4),
 	/* Arm v8 mandates MVFR0.FPDP == {0, 2}. So, piggy back on this for the presence of VFP support */
-	HWCAP_CAP(SYS_MVFR0_EL1, MVFR0_FPDP_SHIFT, FTR_UNSIGNED, 2, CAP_COMPAT_HWCAP, COMPAT_HWCAP_VFP),
-	HWCAP_CAP(SYS_MVFR0_EL1, MVFR0_FPDP_SHIFT, FTR_UNSIGNED, 2, CAP_COMPAT_HWCAP, COMPAT_HWCAP_VFPv3),
-	HWCAP_CAP(SYS_ID_ISAR5_EL1, ID_ISAR5_AES_SHIFT, FTR_UNSIGNED, 2, CAP_COMPAT_HWCAP2, COMPAT_HWCAP2_PMULL),
-	HWCAP_CAP(SYS_ID_ISAR5_EL1, ID_ISAR5_AES_SHIFT, FTR_UNSIGNED, 1, CAP_COMPAT_HWCAP2, COMPAT_HWCAP2_AES),
-	HWCAP_CAP(SYS_ID_ISAR5_EL1, ID_ISAR5_SHA1_SHIFT, FTR_UNSIGNED, 1, CAP_COMPAT_HWCAP2, COMPAT_HWCAP2_SHA1),
-	HWCAP_CAP(SYS_ID_ISAR5_EL1, ID_ISAR5_SHA2_SHIFT, FTR_UNSIGNED, 1, CAP_COMPAT_HWCAP2, COMPAT_HWCAP2_SHA2),
-	HWCAP_CAP(SYS_ID_ISAR5_EL1, ID_ISAR5_CRC32_SHIFT, FTR_UNSIGNED, 1, CAP_COMPAT_HWCAP2, COMPAT_HWCAP2_CRC32),
+	HWCAP_CAP(SYS_MVFR0_EL1, MVFR0_FPDP_SHIFT, 4, FTR_UNSIGNED, 2, CAP_COMPAT_HWCAP, COMPAT_HWCAP_VFP),
+	HWCAP_CAP(SYS_MVFR0_EL1, MVFR0_FPDP_SHIFT, 4, FTR_UNSIGNED, 2, CAP_COMPAT_HWCAP, COMPAT_HWCAP_VFPv3),
+	HWCAP_CAP(SYS_ID_ISAR5_EL1, ID_ISAR5_AES_SHIFT, 4, FTR_UNSIGNED, 2, CAP_COMPAT_HWCAP2, COMPAT_HWCAP2_PMULL),
+	HWCAP_CAP(SYS_ID_ISAR5_EL1, ID_ISAR5_AES_SHIFT, 4, FTR_UNSIGNED, 1, CAP_COMPAT_HWCAP2, COMPAT_HWCAP2_AES),
+	HWCAP_CAP(SYS_ID_ISAR5_EL1, ID_ISAR5_SHA1_SHIFT, 4, FTR_UNSIGNED, 1, CAP_COMPAT_HWCAP2, COMPAT_HWCAP2_SHA1),
+	HWCAP_CAP(SYS_ID_ISAR5_EL1, ID_ISAR5_SHA2_SHIFT, 4, FTR_UNSIGNED, 1, CAP_COMPAT_HWCAP2, COMPAT_HWCAP2_SHA2),
+	HWCAP_CAP(SYS_ID_ISAR5_EL1, ID_ISAR5_CRC32_SHIFT, 4, FTR_UNSIGNED, 1, CAP_COMPAT_HWCAP2, COMPAT_HWCAP2_CRC32),
 #endif
 	{},
 };
@@ -2640,9 +2974,6 @@ static void __init enable_cpu_capabilities(u16 scope_mask)
 		if (!cpus_have_cap(num))
 			continue;
 
-		/* Ensure cpus_have_const_cap(num) works */
-		static_branch_enable(&cpu_hwcap_keys[num]);
-
 		if (boot_scope && caps->cpu_enable)
 			/*
 			 * Capabilities with SCOPE_BOOT_CPU scope are finalised
@@ -2773,6 +3104,23 @@ static void verify_sve_features(void)
 	/* Add checks on other ZCR bits here if necessary */
 }
 
+static void verify_sme_features(void)
+{
+	u64 safe_smcr = read_sanitised_ftr_reg(SYS_SMCR_EL1);
+	u64 smcr = read_smcr_features();
+
+	unsigned int safe_len = safe_smcr & SMCR_ELx_LEN_MASK;
+	unsigned int len = smcr & SMCR_ELx_LEN_MASK;
+
+	if (len < safe_len || vec_verify_vq_map(ARM64_VEC_SME)) {
+		pr_crit("CPU%d: SME: vector length support mismatch\n",
+			smp_processor_id());
+		cpu_die_early();
+	}
+
+	/* Add checks on other SMCR bits here if necessary */
+}
+
 static void verify_hyp_capabilities(void)
 {
 	u64 safe_mmfr1, mmfr0, mmfr1;
@@ -2796,7 +3144,7 @@ static void verify_hyp_capabilities(void)
 
 	/* Verify IPA range */
 	parange = cpuid_feature_extract_unsigned_field(mmfr0,
-				ID_AA64MMFR0_PARANGE_SHIFT);
+				ID_AA64MMFR0_EL1_PARANGE_SHIFT);
 	ipa_max = id_aa64mmfr0_parange_to_phys_shift(parange);
 	if (ipa_max < get_kvm_ipa_limit()) {
 		pr_crit("CPU%d: IPA range mismatch\n", smp_processor_id());
@@ -2825,6 +3173,9 @@ static void verify_local_cpu_capabilities(void)
 	if (system_supports_sve())
 		verify_sve_features();
 
+	if (system_supports_sme())
+		verify_sme_features();
+
 	if (is_hyp_mode_available())
 		verify_hyp_capabilities();
 }
@@ -2889,15 +3240,12 @@ static bool __maybe_unused __system_matches_cap(unsigned int n)
 
 void cpu_set_feature(unsigned int num)
 {
-	WARN_ON(num >= MAX_CPU_FEATURES);
-	elf_hwcap |= BIT(num);
+	set_bit(num, elf_hwcap);
 }
-EXPORT_SYMBOL_GPL(cpu_set_feature);
 
 bool cpu_have_feature(unsigned int num)
 {
-	WARN_ON(num >= MAX_CPU_FEATURES);
-	return elf_hwcap & BIT(num);
+	return test_bit(num, elf_hwcap);
 }
 EXPORT_SYMBOL_GPL(cpu_have_feature);
 
@@ -2908,12 +3256,12 @@ unsigned long cpu_get_elf_hwcap(void)
 	 * note that for userspace compatibility we guarantee that bits 62
 	 * and 63 will always be returned as 0.
 	 */
-	return lower_32_bits(elf_hwcap);
+	return elf_hwcap[0];
 }
 
 unsigned long cpu_get_elf_hwcap2(void)
 {
-	return upper_32_bits(elf_hwcap);
+	return elf_hwcap[1];
 }
 
 static void __init setup_system_capabilities(void)
@@ -2935,18 +3283,18 @@ void __init setup_cpu_features(void)
 	setup_system_capabilities();
 	setup_elf_hwcaps(arm64_elf_hwcaps);
 
-	if (system_supports_32bit_el0())
+	if (system_supports_32bit_el0()) {
 		setup_elf_hwcaps(compat_elf_hwcaps);
+		elf_hwcap_fixup();
+	}
 
 	if (system_uses_ttbr0_pan())
 		pr_info("emulated: Privileged Access Never (PAN) using TTBR0_EL1 switching\n");
 
 	sve_setup();
+	sme_setup();
 	minsigstksz_setup();
 
-	/* Advertise that we have computed the system capabilities */
-	finalize_system_capabilities();
-
 	/*
 	 * Check for sane CTR_EL0.CWG value.
 	 */
@@ -2988,6 +3336,7 @@ static int enable_mismatched_32bit_el0(unsigned int cpu)
 							 cpu_active_mask);
 	get_cpu_device(lucky_winner)->offline_disabled = true;
 	setup_elf_hwcaps(compat_elf_hwcaps);
+	elf_hwcap_fixup();
 	pr_info("Asymmetric 32-bit EL0 support detected on CPU %u; CPU hot-unplug disabled on CPU %u\n",
 		cpu, lucky_winner);
 	return 0;
@@ -3009,12 +3358,12 @@ subsys_initcall_sync(init_32bit_el0_mask);
 
 static void __maybe_unused cpu_enable_cnp(struct arm64_cpu_capabilities const *cap)
 {
-	cpu_replace_ttbr1(lm_alias(swapper_pg_dir));
+	cpu_replace_ttbr1(lm_alias(swapper_pg_dir), idmap_pg_dir);
 }
 
 /*
  * We emulate only the following system register space.
- * Op0 = 0x3, CRn = 0x0, Op1 = 0x0, CRm = [0, 4 - 7]
+ * Op0 = 0x3, CRn = 0x0, Op1 = 0x0, CRm = [0, 2 - 7]
  * See Table C5-6 System instruction encodings for System register accesses,
  * ARMv8 ARM(ARM DDI 0487A.f) for more details.
  */
@@ -3024,7 +3373,7 @@ static inline bool __attribute_const__ is_emulated(u32 id)
 		sys_reg_CRn(id) == 0x0 &&
 		sys_reg_Op1(id) == 0x0 &&
 		(sys_reg_CRm(id) == 0 ||
-		 ((sys_reg_CRm(id) >= 4) && (sys_reg_CRm(id) <= 7))));
+		 ((sys_reg_CRm(id) >= 2) && (sys_reg_CRm(id) <= 7))));
 }
 
 /*
diff --git a/arch/arm64/kernel/cpuidle.c b/arch/arm64/kernel/cpuidle.c
index 03991eeff643..4150e308e99c 100644
--- a/arch/arm64/kernel/cpuidle.c
+++ b/arch/arm64/kernel/cpuidle.c
@@ -13,35 +13,6 @@
 #include <linux/of_device.h>
 #include <linux/psci.h>
 
-#include <asm/cpuidle.h>
-#include <asm/cpu_ops.h>
-
-int arm_cpuidle_init(unsigned int cpu)
-{
-	const struct cpu_operations *ops = get_cpu_ops(cpu);
-	int ret = -EOPNOTSUPP;
-
-	if (ops && ops->cpu_suspend && ops->cpu_init_idle)
-		ret = ops->cpu_init_idle(cpu);
-
-	return ret;
-}
-
-/**
- * arm_cpuidle_suspend() - function to enter a low-power idle state
- * @index: argument to pass to CPU suspend operations
- *
- * Return: 0 on success, -EOPNOTSUPP if CPU suspend hook not initialized, CPU
- * operations back-end error code otherwise.
- */
-int arm_cpuidle_suspend(int index)
-{
-	int cpu = smp_processor_id();
-	const struct cpu_operations *ops = get_cpu_ops(cpu);
-
-	return ops->cpu_suspend(index);
-}
-
 #ifdef CONFIG_ACPI
 
 #include <acpi/processor.h>
@@ -54,6 +25,9 @@ static int psci_acpi_cpu_init_idle(unsigned int cpu)
 	struct acpi_lpi_state *lpi;
 	struct acpi_processor *pr = per_cpu(processors, cpu);
 
+	if (unlikely(!pr || !pr->flags.has_lpi))
+		return -EINVAL;
+
 	/*
 	 * If the PSCI cpu_suspend function hook has not been initialized
 	 * idle states must not be enabled, so bail out
@@ -61,9 +35,6 @@ static int psci_acpi_cpu_init_idle(unsigned int cpu)
 	if (!psci_ops.cpu_suspend)
 		return -EOPNOTSUPP;
 
-	if (unlikely(!pr || !pr->flags.has_lpi))
-		return -EINVAL;
-
 	count = pr->power.count - 1;
 	if (count <= 0)
 		return -ENODEV;
diff --git a/arch/arm64/kernel/cpuinfo.c b/arch/arm64/kernel/cpuinfo.c
index 6e27b759056a..28d4f442b0bc 100644
--- a/arch/arm64/kernel/cpuinfo.c
+++ b/arch/arm64/kernel/cpuinfo.c
@@ -33,12 +33,19 @@
 DEFINE_PER_CPU(struct cpuinfo_arm64, cpu_data);
 static struct cpuinfo_arm64 boot_cpu_data;
 
-static const char *icache_policy_str[] = {
-	[ICACHE_POLICY_VPIPT]		= "VPIPT",
-	[ICACHE_POLICY_RESERVED]	= "RESERVED/UNKNOWN",
-	[ICACHE_POLICY_VIPT]		= "VIPT",
-	[ICACHE_POLICY_PIPT]		= "PIPT",
-};
+static inline const char *icache_policy_str(int l1ip)
+{
+	switch (l1ip) {
+	case CTR_EL0_L1Ip_VPIPT:
+		return "VPIPT";
+	case CTR_EL0_L1Ip_VIPT:
+		return "VIPT";
+	case CTR_EL0_L1Ip_PIPT:
+		return "PIPT";
+	default:
+		return "RESERVED/UNKNOWN";
+	}
+}
 
 unsigned long __icache_flags;
 
@@ -95,6 +102,20 @@ static const char *const hwcap_str[] = {
 	[KERNEL_HWCAP_BTI]		= "bti",
 	[KERNEL_HWCAP_MTE]		= "mte",
 	[KERNEL_HWCAP_ECV]		= "ecv",
+	[KERNEL_HWCAP_AFP]		= "afp",
+	[KERNEL_HWCAP_RPRES]		= "rpres",
+	[KERNEL_HWCAP_MTE3]		= "mte3",
+	[KERNEL_HWCAP_SME]		= "sme",
+	[KERNEL_HWCAP_SME_I16I64]	= "smei16i64",
+	[KERNEL_HWCAP_SME_F64F64]	= "smef64f64",
+	[KERNEL_HWCAP_SME_I8I32]	= "smei8i32",
+	[KERNEL_HWCAP_SME_F16F32]	= "smef16f32",
+	[KERNEL_HWCAP_SME_B16F32]	= "smeb16f32",
+	[KERNEL_HWCAP_SME_F32F32]	= "smef32f32",
+	[KERNEL_HWCAP_SME_FA64]		= "smefa64",
+	[KERNEL_HWCAP_WFXT]		= "wfxt",
+	[KERNEL_HWCAP_EBF16]		= "ebf16",
+	[KERNEL_HWCAP_SVE_EBF16]	= "sveebf16",
 };
 
 #ifdef CONFIG_COMPAT
@@ -255,6 +276,7 @@ static struct kobj_type cpuregs_kobj_type = {
 
 CPUREGS_ATTR_RO(midr_el1, midr);
 CPUREGS_ATTR_RO(revidr_el1, revidr);
+CPUREGS_ATTR_RO(smidr_el1, smidr);
 
 static struct attribute *cpuregs_id_attrs[] = {
 	&cpuregs_attr_midr_el1.attr,
@@ -267,6 +289,16 @@ static const struct attribute_group cpuregs_attr_group = {
 	.name = "identification"
 };
 
+static struct attribute *sme_cpuregs_id_attrs[] = {
+	&cpuregs_attr_smidr_el1.attr,
+	NULL
+};
+
+static const struct attribute_group sme_cpuregs_attr_group = {
+	.attrs = sme_cpuregs_id_attrs,
+	.name = "identification"
+};
+
 static int cpuid_cpu_online(unsigned int cpu)
 {
 	int rc;
@@ -284,6 +316,8 @@ static int cpuid_cpu_online(unsigned int cpu)
 	rc = sysfs_create_group(&info->kobj, &cpuregs_attr_group);
 	if (rc)
 		kobject_del(&info->kobj);
+	if (system_supports_sme())
+		rc = sysfs_merge_group(&info->kobj, &sme_cpuregs_attr_group);
 out:
 	return rc;
 }
@@ -330,19 +364,19 @@ static void cpuinfo_detect_icache_policy(struct cpuinfo_arm64 *info)
 	u32 l1ip = CTR_L1IP(info->reg_ctr);
 
 	switch (l1ip) {
-	case ICACHE_POLICY_PIPT:
+	case CTR_EL0_L1Ip_PIPT:
 		break;
-	case ICACHE_POLICY_VPIPT:
+	case CTR_EL0_L1Ip_VPIPT:
 		set_bit(ICACHEF_VPIPT, &__icache_flags);
 		break;
-	case ICACHE_POLICY_RESERVED:
-	case ICACHE_POLICY_VIPT:
+	case CTR_EL0_L1Ip_VIPT:
+	default:
 		/* Assume aliasing */
 		set_bit(ICACHEF_ALIASING, &__icache_flags);
 		break;
 	}
 
-	pr_info("Detected %s I-cache on CPU%d\n", icache_policy_str[l1ip], cpu);
+	pr_info("Detected %s I-cache on CPU%d\n", icache_policy_str(l1ip), cpu);
 }
 
 static void __cpuinfo_store_cpu_32bit(struct cpuinfo_32bit *info)
@@ -391,12 +425,14 @@ static void __cpuinfo_store_cpu(struct cpuinfo_arm64 *info)
 	info->reg_id_aa64dfr1 = read_cpuid(ID_AA64DFR1_EL1);
 	info->reg_id_aa64isar0 = read_cpuid(ID_AA64ISAR0_EL1);
 	info->reg_id_aa64isar1 = read_cpuid(ID_AA64ISAR1_EL1);
+	info->reg_id_aa64isar2 = read_cpuid(ID_AA64ISAR2_EL1);
 	info->reg_id_aa64mmfr0 = read_cpuid(ID_AA64MMFR0_EL1);
 	info->reg_id_aa64mmfr1 = read_cpuid(ID_AA64MMFR1_EL1);
 	info->reg_id_aa64mmfr2 = read_cpuid(ID_AA64MMFR2_EL1);
 	info->reg_id_aa64pfr0 = read_cpuid(ID_AA64PFR0_EL1);
 	info->reg_id_aa64pfr1 = read_cpuid(ID_AA64PFR1_EL1);
 	info->reg_id_aa64zfr0 = read_cpuid(ID_AA64ZFR0_EL1);
+	info->reg_id_aa64smfr0 = read_cpuid(ID_AA64SMFR0_EL1);
 
 	if (id_aa64pfr1_mte(info->reg_id_aa64pfr1))
 		info->reg_gmid = read_cpuid(GMID_EL1);
@@ -404,10 +440,6 @@ static void __cpuinfo_store_cpu(struct cpuinfo_arm64 *info)
 	if (id_aa64pfr0_32bit_el0(info->reg_id_aa64pfr0))
 		__cpuinfo_store_cpu_32bit(&info->aarch32);
 
-	if (IS_ENABLED(CONFIG_ARM64_SVE) &&
-	    id_aa64pfr0_sve(info->reg_id_aa64pfr0))
-		info->reg_zcr = read_zcr_features();
-
 	cpuinfo_detect_icache_policy(info);
 }
 
diff --git a/arch/arm64/kernel/crash_core.c b/arch/arm64/kernel/crash_core.c
index 314391a156ee..2b65aae332ce 100644
--- a/arch/arm64/kernel/crash_core.c
+++ b/arch/arm64/kernel/crash_core.c
@@ -20,6 +20,12 @@ void arch_crash_save_vmcoreinfo(void)
 {
 	VMCOREINFO_NUMBER(VA_BITS);
 	/* Please note VMCOREINFO_NUMBER() uses "%d", not "%x" */
+	vmcoreinfo_append_str("NUMBER(MODULES_VADDR)=0x%lx\n", MODULES_VADDR);
+	vmcoreinfo_append_str("NUMBER(MODULES_END)=0x%lx\n", MODULES_END);
+	vmcoreinfo_append_str("NUMBER(VMALLOC_START)=0x%lx\n", VMALLOC_START);
+	vmcoreinfo_append_str("NUMBER(VMALLOC_END)=0x%lx\n", VMALLOC_END);
+	vmcoreinfo_append_str("NUMBER(VMEMMAP_START)=0x%lx\n", VMEMMAP_START);
+	vmcoreinfo_append_str("NUMBER(VMEMMAP_END)=0x%lx\n", VMEMMAP_END);
 	vmcoreinfo_append_str("NUMBER(kimage_voffset)=0x%llx\n",
 						kimage_voffset);
 	vmcoreinfo_append_str("NUMBER(PHYS_OFFSET)=0x%llx\n",
diff --git a/arch/arm64/kernel/crash_dump.c b/arch/arm64/kernel/crash_dump.c
index 58303a9ec32c..670e4ce81822 100644
--- a/arch/arm64/kernel/crash_dump.c
+++ b/arch/arm64/kernel/crash_dump.c
@@ -9,25 +9,11 @@
 #include <linux/crash_dump.h>
 #include <linux/errno.h>
 #include <linux/io.h>
-#include <linux/memblock.h>
-#include <linux/uaccess.h>
+#include <linux/uio.h>
 #include <asm/memory.h>
 
-/**
- * copy_oldmem_page() - copy one page from old kernel memory
- * @pfn: page frame number to be copied
- * @buf: buffer where the copied page is placed
- * @csize: number of bytes to copy
- * @offset: offset in bytes into the page
- * @userbuf: if set, @buf is in a user address space
- *
- * This function copies one page from old kernel memory into buffer pointed by
- * @buf. If @buf is in userspace, set @userbuf to %1. Returns number of bytes
- * copied or negative error in case of failure.
- */
-ssize_t copy_oldmem_page(unsigned long pfn, char *buf,
-			 size_t csize, unsigned long offset,
-			 int userbuf)
+ssize_t copy_oldmem_page(struct iov_iter *iter, unsigned long pfn,
+			 size_t csize, unsigned long offset)
 {
 	void *vaddr;
 
@@ -38,14 +24,7 @@ ssize_t copy_oldmem_page(unsigned long pfn, char *buf,
 	if (!vaddr)
 		return -ENOMEM;
 
-	if (userbuf) {
-		if (copy_to_user((char __user *)buf, vaddr + offset, csize)) {
-			memunmap(vaddr);
-			return -EFAULT;
-		}
-	} else {
-		memcpy(buf, vaddr + offset, csize);
-	}
+	csize = copy_to_iter(vaddr + offset, csize, iter);
 
 	memunmap(vaddr);
 
diff --git a/arch/arm64/kernel/debug-monitors.c b/arch/arm64/kernel/debug-monitors.c
index 4f3661eeb7ec..3da09778267e 100644
--- a/arch/arm64/kernel/debug-monitors.c
+++ b/arch/arm64/kernel/debug-monitors.c
@@ -28,7 +28,7 @@
 u8 debug_monitors_arch(void)
 {
 	return cpuid_feature_extract_unsigned_field(read_sanitised_ftr_reg(SYS_ID_AA64DFR0_EL1),
-						ID_AA64DFR0_DEBUGVER_SHIFT);
+						ID_AA64DFR0_EL1_DebugVer_SHIFT);
 }
 
 /*
@@ -202,7 +202,7 @@ void unregister_kernel_step_hook(struct step_hook *hook)
  * So we call all the registered handlers, until the right handler is
  * found which returns zero.
  */
-static int call_step_hook(struct pt_regs *regs, unsigned int esr)
+static int call_step_hook(struct pt_regs *regs, unsigned long esr)
 {
 	struct step_hook *hook;
 	struct list_head *list;
@@ -238,7 +238,7 @@ static void send_user_sigtrap(int si_code)
 			      "User debug trap");
 }
 
-static int single_step_handler(unsigned long unused, unsigned int esr,
+static int single_step_handler(unsigned long unused, unsigned long esr,
 			       struct pt_regs *regs)
 {
 	bool handler_found = false;
@@ -299,11 +299,11 @@ void unregister_kernel_break_hook(struct break_hook *hook)
 	unregister_debug_hook(&hook->node);
 }
 
-static int call_break_hook(struct pt_regs *regs, unsigned int esr)
+static int call_break_hook(struct pt_regs *regs, unsigned long esr)
 {
 	struct break_hook *hook;
 	struct list_head *list;
-	int (*fn)(struct pt_regs *regs, unsigned int esr) = NULL;
+	int (*fn)(struct pt_regs *regs, unsigned long esr) = NULL;
 
 	list = user_mode(regs) ? &user_break_hook : &kernel_break_hook;
 
@@ -312,7 +312,7 @@ static int call_break_hook(struct pt_regs *regs, unsigned int esr)
 	 * entirely not preemptible, and we can use rcu list safely here.
 	 */
 	list_for_each_entry_rcu(hook, list, node) {
-		unsigned int comment = esr & ESR_ELx_BRK64_ISS_COMMENT_MASK;
+		unsigned long comment = esr & ESR_ELx_BRK64_ISS_COMMENT_MASK;
 
 		if ((comment & ~hook->mask) == hook->imm)
 			fn = hook->fn;
@@ -322,7 +322,7 @@ static int call_break_hook(struct pt_regs *regs, unsigned int esr)
 }
 NOKPROBE_SYMBOL(call_break_hook);
 
-static int brk_handler(unsigned long unused, unsigned int esr,
+static int brk_handler(unsigned long unused, unsigned long esr,
 		       struct pt_regs *regs)
 {
 	if (call_break_hook(regs, esr) == DBG_HOOK_HANDLED)
diff --git a/arch/arm64/kernel/efi-rt-wrapper.S b/arch/arm64/kernel/efi-rt-wrapper.S
index 75691a2641c1..67babd5f04c2 100644
--- a/arch/arm64/kernel/efi-rt-wrapper.S
+++ b/arch/arm64/kernel/efi-rt-wrapper.S
@@ -6,7 +6,7 @@
 #include <linux/linkage.h>
 
 SYM_FUNC_START(__efi_rt_asm_wrapper)
-	stp	x29, x30, [sp, #-32]!
+	stp	x29, x30, [sp, #-112]!
 	mov	x29, sp
 
 	/*
@@ -17,6 +17,20 @@ SYM_FUNC_START(__efi_rt_asm_wrapper)
 	stp	x1, x18, [sp, #16]
 
 	/*
+	 * Preserve all callee saved registers and record the stack pointer
+	 * value in a per-CPU variable so we can recover from synchronous
+	 * exceptions occurring while running the firmware routines.
+	 */
+	stp	x19, x20, [sp, #32]
+	stp	x21, x22, [sp, #48]
+	stp	x23, x24, [sp, #64]
+	stp	x25, x26, [sp, #80]
+	stp	x27, x28, [sp, #96]
+
+	adr_this_cpu	x8, __efi_rt_asm_recover_sp, x9
+	str		x29, [x8]
+
+	/*
 	 * We are lucky enough that no EFI runtime services take more than
 	 * 5 arguments, so all are passed in registers rather than via the
 	 * stack.
@@ -31,7 +45,7 @@ SYM_FUNC_START(__efi_rt_asm_wrapper)
 
 	ldp	x1, x2, [sp, #16]
 	cmp	x2, x18
-	ldp	x29, x30, [sp], #32
+	ldp	x29, x30, [sp], #112
 	b.ne	0f
 	ret
 0:
@@ -45,3 +59,18 @@ SYM_FUNC_START(__efi_rt_asm_wrapper)
 	mov	x18, x2
 	b	efi_handle_corrupted_x18	// tail call
 SYM_FUNC_END(__efi_rt_asm_wrapper)
+
+SYM_FUNC_START(__efi_rt_asm_recover)
+	ldr_this_cpu	x8, __efi_rt_asm_recover_sp, x9
+	mov		sp, x8
+
+	ldp	x0,  x18, [sp, #16]
+	ldp	x19, x20, [sp, #32]
+	ldp	x21, x22, [sp, #48]
+	ldp	x23, x24, [sp, #64]
+	ldp	x25, x26, [sp, #80]
+	ldp	x27, x28, [sp, #96]
+	ldp	x29, x30, [sp], #112
+
+	b	efi_handle_runtime_exception
+SYM_FUNC_END(__efi_rt_asm_recover)
diff --git a/arch/arm64/kernel/efi.c b/arch/arm64/kernel/efi.c
index e1be6c429810..ee53f2a0aa03 100644
--- a/arch/arm64/kernel/efi.c
+++ b/arch/arm64/kernel/efi.c
@@ -9,9 +9,18 @@
 
 #include <linux/efi.h>
 #include <linux/init.h>
+#include <linux/percpu.h>
 
 #include <asm/efi.h>
 
+static bool region_is_misaligned(const efi_memory_desc_t *md)
+{
+	if (PAGE_SIZE == EFI_PAGE_SIZE)
+		return false;
+	return !PAGE_ALIGNED(md->phys_addr) ||
+	       !PAGE_ALIGNED(md->num_pages << EFI_PAGE_SHIFT);
+}
+
 /*
  * Only regions of type EFI_RUNTIME_SERVICES_CODE need to be
  * executable, everything else can be mapped with the XN bits
@@ -25,14 +34,22 @@ static __init pteval_t create_mapping_protection(efi_memory_desc_t *md)
 	if (type == EFI_MEMORY_MAPPED_IO)
 		return PROT_DEVICE_nGnRE;
 
-	if (WARN_ONCE(!PAGE_ALIGNED(md->phys_addr),
-		      "UEFI Runtime regions are not aligned to 64 KB -- buggy firmware?"))
+	if (region_is_misaligned(md)) {
+		static bool __initdata code_is_misaligned;
+
 		/*
-		 * If the region is not aligned to the page size of the OS, we
-		 * can not use strict permissions, since that would also affect
-		 * the mapping attributes of the adjacent regions.
+		 * Regions that are not aligned to the OS page size cannot be
+		 * mapped with strict permissions, as those might interfere
+		 * with the permissions that are needed by the adjacent
+		 * region's mapping. However, if we haven't encountered any
+		 * misaligned runtime code regions so far, we can safely use
+		 * non-executable permissions for non-code regions.
 		 */
-		return pgprot_val(PAGE_KERNEL_EXEC);
+		code_is_misaligned |= (type == EFI_RUNTIME_SERVICES_CODE);
+
+		return code_is_misaligned ? pgprot_val(PAGE_KERNEL_EXEC)
+					  : pgprot_val(PAGE_KERNEL);
+	}
 
 	/* R-- */
 	if ((attr & (EFI_MEMORY_XP | EFI_MEMORY_RO)) ==
@@ -63,19 +80,16 @@ int __init efi_create_mapping(struct mm_struct *mm, efi_memory_desc_t *md)
 	bool page_mappings_only = (md->type == EFI_RUNTIME_SERVICES_CODE ||
 				   md->type == EFI_RUNTIME_SERVICES_DATA);
 
-	if (!PAGE_ALIGNED(md->phys_addr) ||
-	    !PAGE_ALIGNED(md->num_pages << EFI_PAGE_SHIFT)) {
-		/*
-		 * If the end address of this region is not aligned to page
-		 * size, the mapping is rounded up, and may end up sharing a
-		 * page frame with the next UEFI memory region. If we create
-		 * a block entry now, we may need to split it again when mapping
-		 * the next region, and support for that is going to be removed
-		 * from the MMU routines. So avoid block mappings altogether in
-		 * that case.
-		 */
+	/*
+	 * If this region is not aligned to the page size used by the OS, the
+	 * mapping will be rounded outwards, and may end up sharing a page
+	 * frame with an adjacent runtime memory region. Given that the page
+	 * table descriptor covering the shared page will be rewritten when the
+	 * adjacent region gets mapped, we must avoid block mappings here so we
+	 * don't have to worry about splitting them when that happens.
+	 */
+	if (region_is_misaligned(md))
 		page_mappings_only = true;
-	}
 
 	create_pgd_mapping(mm, md->phys_addr, md->virt_addr,
 			   md->num_pages << EFI_PAGE_SHIFT,
@@ -102,6 +116,9 @@ int __init efi_set_mapping_permissions(struct mm_struct *mm,
 	BUG_ON(md->type != EFI_RUNTIME_SERVICES_CODE &&
 	       md->type != EFI_RUNTIME_SERVICES_DATA);
 
+	if (region_is_misaligned(md))
+		return 0;
+
 	/*
 	 * Calling apply_to_page_range() is only safe on regions that are
 	 * guaranteed to be mapped down to pages. Since we are only called
@@ -128,3 +145,28 @@ asmlinkage efi_status_t efi_handle_corrupted_x18(efi_status_t s, const char *f)
 	pr_err_ratelimited(FW_BUG "register x18 corrupted by EFI %s\n", f);
 	return s;
 }
+
+asmlinkage DEFINE_PER_CPU(u64, __efi_rt_asm_recover_sp);
+
+asmlinkage efi_status_t __efi_rt_asm_recover(void);
+
+asmlinkage efi_status_t efi_handle_runtime_exception(const char *f)
+{
+	pr_err(FW_BUG "Synchronous exception occurred in EFI runtime service %s()\n", f);
+	clear_bit(EFI_RUNTIME_SERVICES, &efi.flags);
+	return EFI_ABORTED;
+}
+
+bool efi_runtime_fixup_exception(struct pt_regs *regs, const char *msg)
+{
+	 /* Check whether the exception occurred while running the firmware */
+	if (current_work() != &efi_rts_work.work || regs->pc >= TASK_SIZE_64)
+		return false;
+
+	pr_err(FW_BUG "Unable to handle %s in EFI runtime service\n", msg);
+	add_taint(TAINT_FIRMWARE_WORKAROUND, LOCKDEP_STILL_OK);
+	dump_stack();
+
+	regs->pc = (u64)__efi_rt_asm_recover;
+	return true;
+}
diff --git a/arch/arm64/kernel/elfcore.c b/arch/arm64/kernel/elfcore.c
new file mode 100644
index 000000000000..27ef7ad3ffd2
--- /dev/null
+++ b/arch/arm64/kernel/elfcore.c
@@ -0,0 +1,143 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+#include <linux/coredump.h>
+#include <linux/elfcore.h>
+#include <linux/kernel.h>
+#include <linux/mm.h>
+
+#include <asm/cpufeature.h>
+#include <asm/mte.h>
+
+#define for_each_mte_vma(vmi, vma)					\
+	if (system_supports_mte())					\
+		for_each_vma(vmi, vma)					\
+			if (vma->vm_flags & VM_MTE)
+
+static unsigned long mte_vma_tag_dump_size(struct vm_area_struct *vma)
+{
+	if (vma->vm_flags & VM_DONTDUMP)
+		return 0;
+
+	return vma_pages(vma) * MTE_PAGE_TAG_STORAGE;
+}
+
+/* Derived from dump_user_range(); start/end must be page-aligned */
+static int mte_dump_tag_range(struct coredump_params *cprm,
+			      unsigned long start, unsigned long end)
+{
+	int ret = 1;
+	unsigned long addr;
+	void *tags = NULL;
+
+	for (addr = start; addr < end; addr += PAGE_SIZE) {
+		struct page *page = get_dump_page(addr);
+
+		/*
+		 * get_dump_page() returns NULL when encountering an empty
+		 * page table entry that would otherwise have been filled with
+		 * the zero page. Skip the equivalent tag dump which would
+		 * have been all zeros.
+		 */
+		if (!page) {
+			dump_skip(cprm, MTE_PAGE_TAG_STORAGE);
+			continue;
+		}
+
+		/*
+		 * Pages mapped in user space as !pte_access_permitted() (e.g.
+		 * PROT_EXEC only) may not have the PG_mte_tagged flag set.
+		 */
+		if (!test_bit(PG_mte_tagged, &page->flags)) {
+			put_page(page);
+			dump_skip(cprm, MTE_PAGE_TAG_STORAGE);
+			continue;
+		}
+
+		if (!tags) {
+			tags = mte_allocate_tag_storage();
+			if (!tags) {
+				put_page(page);
+				ret = 0;
+				break;
+			}
+		}
+
+		mte_save_page_tags(page_address(page), tags);
+		put_page(page);
+		if (!dump_emit(cprm, tags, MTE_PAGE_TAG_STORAGE)) {
+			mte_free_tag_storage(tags);
+			ret = 0;
+			break;
+		}
+	}
+
+	if (tags)
+		mte_free_tag_storage(tags);
+
+	return ret;
+}
+
+Elf_Half elf_core_extra_phdrs(void)
+{
+	struct vm_area_struct *vma;
+	int vma_count = 0;
+	VMA_ITERATOR(vmi, current->mm, 0);
+
+	for_each_mte_vma(vmi, vma)
+		vma_count++;
+
+	return vma_count;
+}
+
+int elf_core_write_extra_phdrs(struct coredump_params *cprm, loff_t offset)
+{
+	struct vm_area_struct *vma;
+	VMA_ITERATOR(vmi, current->mm, 0);
+
+	for_each_mte_vma(vmi, vma) {
+		struct elf_phdr phdr;
+
+		phdr.p_type = PT_AARCH64_MEMTAG_MTE;
+		phdr.p_offset = offset;
+		phdr.p_vaddr = vma->vm_start;
+		phdr.p_paddr = 0;
+		phdr.p_filesz = mte_vma_tag_dump_size(vma);
+		phdr.p_memsz = vma->vm_end - vma->vm_start;
+		offset += phdr.p_filesz;
+		phdr.p_flags = 0;
+		phdr.p_align = 0;
+
+		if (!dump_emit(cprm, &phdr, sizeof(phdr)))
+			return 0;
+	}
+
+	return 1;
+}
+
+size_t elf_core_extra_data_size(void)
+{
+	struct vm_area_struct *vma;
+	size_t data_size = 0;
+	VMA_ITERATOR(vmi, current->mm, 0);
+
+	for_each_mte_vma(vmi, vma)
+		data_size += mte_vma_tag_dump_size(vma);
+
+	return data_size;
+}
+
+int elf_core_write_extra_data(struct coredump_params *cprm)
+{
+	struct vm_area_struct *vma;
+	VMA_ITERATOR(vmi, current->mm, 0);
+
+	for_each_mte_vma(vmi, vma) {
+		if (vma->vm_flags & VM_DONTDUMP)
+			continue;
+
+		if (!mte_dump_tag_range(cprm, vma->vm_start, vma->vm_end))
+			return 0;
+	}
+
+	return 1;
+}
diff --git a/arch/arm64/kernel/entry-common.c b/arch/arm64/kernel/entry-common.c
index f7408edf8571..27369fa1c032 100644
--- a/arch/arm64/kernel/entry-common.c
+++ b/arch/arm64/kernel/entry-common.c
@@ -6,6 +6,7 @@
  */
 
 #include <linux/context_tracking.h>
+#include <linux/kasan.h>
 #include <linux/linkage.h>
 #include <linux/lockdep.h>
 #include <linux/ptrace.h>
@@ -40,7 +41,7 @@ static __always_inline void __enter_from_kernel_mode(struct pt_regs *regs)
 
 	if (!IS_ENABLED(CONFIG_TINY_RCU) && is_idle_task(current)) {
 		lockdep_hardirqs_off(CALLER_ADDR0);
-		rcu_irq_enter();
+		ct_irq_enter();
 		trace_hardirqs_off_finish();
 
 		regs->exit_rcu = true;
@@ -56,6 +57,7 @@ static void noinstr enter_from_kernel_mode(struct pt_regs *regs)
 {
 	__enter_from_kernel_mode(regs);
 	mte_check_tfsr_entry();
+	mte_disable_tco_entry(current);
 }
 
 /*
@@ -73,8 +75,8 @@ static __always_inline void __exit_to_kernel_mode(struct pt_regs *regs)
 	if (interrupts_enabled(regs)) {
 		if (regs->exit_rcu) {
 			trace_hardirqs_on_prepare();
-			lockdep_hardirqs_on_prepare(CALLER_ADDR0);
-			rcu_irq_exit();
+			lockdep_hardirqs_on_prepare();
+			ct_irq_exit();
 			lockdep_hardirqs_on(CALLER_ADDR0);
 			return;
 		}
@@ -82,7 +84,7 @@ static __always_inline void __exit_to_kernel_mode(struct pt_regs *regs)
 		trace_hardirqs_on();
 	} else {
 		if (regs->exit_rcu)
-			rcu_irq_exit();
+			ct_irq_exit();
 	}
 }
 
@@ -103,6 +105,7 @@ static __always_inline void __enter_from_user_mode(void)
 	CT_WARN_ON(ct_state() != CONTEXT_USER);
 	user_exit_irqoff();
 	trace_hardirqs_off_finish();
+	mte_disable_tco_entry(current);
 }
 
 static __always_inline void enter_from_user_mode(struct pt_regs *regs)
@@ -118,7 +121,7 @@ static __always_inline void enter_from_user_mode(struct pt_regs *regs)
 static __always_inline void __exit_to_user_mode(void)
 {
 	trace_hardirqs_on_prepare();
-	lockdep_hardirqs_on_prepare(CALLER_ADDR0);
+	lockdep_hardirqs_on_prepare();
 	user_enter_irqoff();
 	lockdep_hardirqs_on(CALLER_ADDR0);
 }
@@ -129,7 +132,7 @@ static __always_inline void prepare_exit_to_user_mode(struct pt_regs *regs)
 
 	local_daif_mask();
 
-	flags = READ_ONCE(current_thread_info()->flags);
+	flags = read_thread_flags();
 	if (unlikely(flags & _TIF_WORK_MASK))
 		do_notify_resume(regs, flags);
 }
@@ -158,7 +161,7 @@ static void noinstr arm64_enter_nmi(struct pt_regs *regs)
 	__nmi_enter();
 	lockdep_hardirqs_off(CALLER_ADDR0);
 	lockdep_hardirq_enter();
-	rcu_nmi_enter();
+	ct_nmi_enter();
 
 	trace_hardirqs_off_finish();
 	ftrace_nmi_enter();
@@ -176,10 +179,10 @@ static void noinstr arm64_exit_nmi(struct pt_regs *regs)
 	ftrace_nmi_exit();
 	if (restore) {
 		trace_hardirqs_on_prepare();
-		lockdep_hardirqs_on_prepare(CALLER_ADDR0);
+		lockdep_hardirqs_on_prepare();
 	}
 
-	rcu_nmi_exit();
+	ct_nmi_exit();
 	lockdep_hardirq_exit();
 	if (restore)
 		lockdep_hardirqs_on(CALLER_ADDR0);
@@ -196,7 +199,7 @@ static void noinstr arm64_enter_el1_dbg(struct pt_regs *regs)
 	regs->lockdep_hardirqs = lockdep_hardirqs_enabled();
 
 	lockdep_hardirqs_off(CALLER_ADDR0);
-	rcu_nmi_enter();
+	ct_nmi_enter();
 
 	trace_hardirqs_off_finish();
 }
@@ -212,17 +215,34 @@ static void noinstr arm64_exit_el1_dbg(struct pt_regs *regs)
 
 	if (restore) {
 		trace_hardirqs_on_prepare();
-		lockdep_hardirqs_on_prepare(CALLER_ADDR0);
+		lockdep_hardirqs_on_prepare();
 	}
 
-	rcu_nmi_exit();
+	ct_nmi_exit();
 	if (restore)
 		lockdep_hardirqs_on(CALLER_ADDR0);
 }
 
+#ifdef CONFIG_PREEMPT_DYNAMIC
+DEFINE_STATIC_KEY_TRUE(sk_dynamic_irqentry_exit_cond_resched);
+#define need_irq_preemption() \
+	(static_branch_unlikely(&sk_dynamic_irqentry_exit_cond_resched))
+#else
+#define need_irq_preemption()	(IS_ENABLED(CONFIG_PREEMPTION))
+#endif
+
 static void __sched arm64_preempt_schedule_irq(void)
 {
-	lockdep_assert_irqs_disabled();
+	if (!need_irq_preemption())
+		return;
+
+	/*
+	 * Note: thread_info::preempt_count includes both thread_info::count
+	 * and thread_info::need_resched, and is not equivalent to
+	 * preempt_count().
+	 */
+	if (READ_ONCE(current_thread_info()->preempt_count) != 0)
+		return;
 
 	/*
 	 * DAIF.DA are cleared at the start of IRQ/FIQ handling, and when GIC
@@ -262,13 +282,13 @@ extern void (*handle_arch_irq)(struct pt_regs *);
 extern void (*handle_arch_fiq)(struct pt_regs *);
 
 static void noinstr __panic_unhandled(struct pt_regs *regs, const char *vector,
-				      unsigned int esr)
+				      unsigned long esr)
 {
 	arm64_enter_nmi(regs);
 
 	console_verbose();
 
-	pr_crit("Unhandled %s exception on CPU%d, ESR 0x%08x -- %s\n",
+	pr_crit("Unhandled %s exception on CPU%d, ESR 0x%016lx -- %s\n",
 		vector, smp_processor_id(), esr,
 		esr_get_class_string(esr));
 
@@ -309,7 +329,8 @@ static void cortex_a76_erratum_1463225_svc_handler(void)
 	__this_cpu_write(__in_cortex_a76_erratum_1463225_wa, 0);
 }
 
-static bool cortex_a76_erratum_1463225_debug_handler(struct pt_regs *regs)
+static __always_inline bool
+cortex_a76_erratum_1463225_debug_handler(struct pt_regs *regs)
 {
 	if (!__this_cpu_read(__in_cortex_a76_erratum_1463225_wa))
 		return false;
@@ -359,11 +380,20 @@ static void noinstr el1_pc(struct pt_regs *regs, unsigned long esr)
 	exit_to_kernel_mode(regs);
 }
 
-static void noinstr el1_undef(struct pt_regs *regs)
+static void noinstr el1_undef(struct pt_regs *regs, unsigned long esr)
 {
 	enter_from_kernel_mode(regs);
 	local_daif_inherit(regs);
-	do_undefinstr(regs);
+	do_undefinstr(regs, esr);
+	local_daif_mask();
+	exit_to_kernel_mode(regs);
+}
+
+static void noinstr el1_bti(struct pt_regs *regs, unsigned long esr)
+{
+	enter_from_kernel_mode(regs);
+	local_daif_inherit(regs);
+	do_el1_bti(regs, esr);
 	local_daif_mask();
 	exit_to_kernel_mode(regs);
 }
@@ -382,7 +412,7 @@ static void noinstr el1_fpac(struct pt_regs *regs, unsigned long esr)
 {
 	enter_from_kernel_mode(regs);
 	local_daif_inherit(regs);
-	do_ptrauth_fault(regs, esr);
+	do_el1_fpac(regs, esr);
 	local_daif_mask();
 	exit_to_kernel_mode(regs);
 }
@@ -405,7 +435,10 @@ asmlinkage void noinstr el1h_64_sync_handler(struct pt_regs *regs)
 		break;
 	case ESR_ELx_EC_SYS64:
 	case ESR_ELx_EC_UNKNOWN:
-		el1_undef(regs);
+		el1_undef(regs, esr);
+		break;
+	case ESR_ELx_EC_BTI:
+		el1_bti(regs, esr);
 		break;
 	case ESR_ELx_EC_BREAKPT_CUR:
 	case ESR_ELx_EC_SOFTSTP_CUR:
@@ -438,14 +471,7 @@ static __always_inline void __el1_irq(struct pt_regs *regs,
 	do_interrupt_handler(regs, handler);
 	irq_exit_rcu();
 
-	/*
-	 * Note: thread_info::preempt_count includes both thread_info::count
-	 * and thread_info::need_resched, and is not equivalent to
-	 * preempt_count().
-	 */
-	if (IS_ENABLED(CONFIG_PREEMPTION) &&
-	    READ_ONCE(current_thread_info()->preempt_count) == 0)
-		arm64_preempt_schedule_irq();
+	arm64_preempt_schedule_irq();
 
 	exit_to_kernel_mode(regs);
 }
@@ -524,6 +550,14 @@ static void noinstr el0_sve_acc(struct pt_regs *regs, unsigned long esr)
 	exit_to_user_mode(regs);
 }
 
+static void noinstr el0_sme_acc(struct pt_regs *regs, unsigned long esr)
+{
+	enter_from_user_mode(regs);
+	local_daif_restore(DAIF_PROCCTX);
+	do_sme_acc(esr, regs);
+	exit_to_user_mode(regs);
+}
+
 static void noinstr el0_fpsimd_exc(struct pt_regs *regs, unsigned long esr)
 {
 	enter_from_user_mode(regs);
@@ -561,11 +595,11 @@ static void noinstr el0_sp(struct pt_regs *regs, unsigned long esr)
 	exit_to_user_mode(regs);
 }
 
-static void noinstr el0_undef(struct pt_regs *regs)
+static void noinstr el0_undef(struct pt_regs *regs, unsigned long esr)
 {
 	enter_from_user_mode(regs);
 	local_daif_restore(DAIF_PROCCTX);
-	do_undefinstr(regs);
+	do_undefinstr(regs, esr);
 	exit_to_user_mode(regs);
 }
 
@@ -573,7 +607,7 @@ static void noinstr el0_bti(struct pt_regs *regs)
 {
 	enter_from_user_mode(regs);
 	local_daif_restore(DAIF_PROCCTX);
-	do_bti(regs);
+	do_el0_bti(regs);
 	exit_to_user_mode(regs);
 }
 
@@ -608,7 +642,7 @@ static void noinstr el0_fpac(struct pt_regs *regs, unsigned long esr)
 {
 	enter_from_user_mode(regs);
 	local_daif_restore(DAIF_PROCCTX);
-	do_ptrauth_fault(regs, esr);
+	do_el0_fpac(regs, esr);
 	exit_to_user_mode(regs);
 }
 
@@ -632,6 +666,9 @@ asmlinkage void noinstr el0t_64_sync_handler(struct pt_regs *regs)
 	case ESR_ELx_EC_SVE:
 		el0_sve_acc(regs, esr);
 		break;
+	case ESR_ELx_EC_SME:
+		el0_sme_acc(regs, esr);
+		break;
 	case ESR_ELx_EC_FP_EXC64:
 		el0_fpsimd_exc(regs, esr);
 		break;
@@ -646,7 +683,7 @@ asmlinkage void noinstr el0t_64_sync_handler(struct pt_regs *regs)
 		el0_pc(regs, esr);
 		break;
 	case ESR_ELx_EC_UNKNOWN:
-		el0_undef(regs);
+		el0_undef(regs, esr);
 		break;
 	case ESR_ELx_EC_BTI:
 		el0_bti(regs);
@@ -764,7 +801,7 @@ asmlinkage void noinstr el0t_32_sync_handler(struct pt_regs *regs)
 	case ESR_ELx_EC_CP14_MR:
 	case ESR_ELx_EC_CP14_LS:
 	case ESR_ELx_EC_CP14_64:
-		el0_undef(regs);
+		el0_undef(regs, esr);
 		break;
 	case ESR_ELx_EC_CP15_32:
 	case ESR_ELx_EC_CP15_64:
@@ -805,7 +842,7 @@ UNHANDLED(el0t, 32, error)
 #ifdef CONFIG_VMAP_STACK
 asmlinkage void noinstr handle_bad_stack(struct pt_regs *regs)
 {
-	unsigned int esr = read_sysreg(esr_el1);
+	unsigned long esr = read_sysreg(esr_el1);
 	unsigned long far = read_sysreg(far_el1);
 
 	arm64_enter_nmi(regs);
diff --git a/arch/arm64/kernel/entry-fpsimd.S b/arch/arm64/kernel/entry-fpsimd.S
index dc242e269f9a..229436f33df5 100644
--- a/arch/arm64/kernel/entry-fpsimd.S
+++ b/arch/arm64/kernel/entry-fpsimd.S
@@ -86,3 +86,39 @@ SYM_FUNC_START(sve_flush_live)
 SYM_FUNC_END(sve_flush_live)
 
 #endif /* CONFIG_ARM64_SVE */
+
+#ifdef CONFIG_ARM64_SME
+
+SYM_FUNC_START(sme_get_vl)
+	_sme_rdsvl	0, 1
+	ret
+SYM_FUNC_END(sme_get_vl)
+
+SYM_FUNC_START(sme_set_vq)
+	sme_load_vq x0, x1, x2
+	ret
+SYM_FUNC_END(sme_set_vq)
+
+/*
+ * Save the SME state
+ *
+ * x0 - pointer to buffer for state
+ */
+SYM_FUNC_START(za_save_state)
+	_sme_rdsvl	1, 1		// x1 = VL/8
+	sme_save_za 0, x1, 12
+	ret
+SYM_FUNC_END(za_save_state)
+
+/*
+ * Load the SME state
+ *
+ * x0 - pointer to buffer for state
+ */
+SYM_FUNC_START(za_load_state)
+	_sme_rdsvl	1, 1		// x1 = VL/8
+	sme_load_za 0, x1, 12
+	ret
+SYM_FUNC_END(za_load_state)
+
+#endif /* CONFIG_ARM64_SME */
diff --git a/arch/arm64/kernel/entry-ftrace.S b/arch/arm64/kernel/entry-ftrace.S
index 8cf970d219f5..795344ab4ec4 100644
--- a/arch/arm64/kernel/entry-ftrace.S
+++ b/arch/arm64/kernel/entry-ftrace.S
@@ -7,6 +7,7 @@
  */
 
 #include <linux/linkage.h>
+#include <linux/cfi_types.h>
 #include <asm/asm-offsets.h>
 #include <asm/assembler.h>
 #include <asm/ftrace.h>
@@ -77,17 +78,13 @@
 	.endm
 
 SYM_CODE_START(ftrace_regs_caller)
-#ifdef BTI_C
-	BTI_C
-#endif
+	bti	c
 	ftrace_regs_entry	1
 	b	ftrace_common
 SYM_CODE_END(ftrace_regs_caller)
 
 SYM_CODE_START(ftrace_caller)
-#ifdef BTI_C
-	BTI_C
-#endif
+	bti	c
 	ftrace_regs_entry	0
 	b	ftrace_common
 SYM_CODE_END(ftrace_caller)
@@ -101,18 +98,11 @@ SYM_CODE_START(ftrace_common)
 SYM_INNER_LABEL(ftrace_call, SYM_L_GLOBAL)
 	bl	ftrace_stub
 
-#ifdef CONFIG_FUNCTION_GRAPH_TRACER
-SYM_INNER_LABEL(ftrace_graph_call, SYM_L_GLOBAL) // ftrace_graph_caller();
-	nop				// If enabled, this will be replaced
-					// "b ftrace_graph_caller"
-#endif
-
 /*
  * At the callsite x0-x8 and x19-x30 were live. Any C code will have preserved
  * x19-x29 per the AAPCS, and we created frame records upon entry, so we need
  * to restore x0-x8, x29, and x30.
  */
-ftrace_common_return:
 	/* Restore function arguments */
 	ldp	x0, x1, [sp]
 	ldp	x2, x3, [sp, #S_X2]
@@ -131,17 +121,6 @@ ftrace_common_return:
 	ret	x9
 SYM_CODE_END(ftrace_common)
 
-#ifdef CONFIG_FUNCTION_GRAPH_TRACER
-SYM_CODE_START(ftrace_graph_caller)
-	ldr	x0, [sp, #S_PC]
-	sub	x0, x0, #AARCH64_INSN_SIZE	// ip (callsite's BL insn)
-	add	x1, sp, #S_LR			// parent_ip (callsite's LR)
-	ldr	x2, [sp, #PT_REGS_SIZE]	   	// parent fp (callsite's FP)
-	bl	prepare_ftrace_return
-	b	ftrace_common_return
-SYM_CODE_END(ftrace_graph_caller)
-#endif
-
 #else /* CONFIG_DYNAMIC_FTRACE_WITH_REGS */
 
 /*
@@ -316,10 +295,14 @@ SYM_FUNC_END(ftrace_graph_caller)
 #endif /* CONFIG_FUNCTION_GRAPH_TRACER */
 #endif /* CONFIG_DYNAMIC_FTRACE_WITH_REGS */
 
-SYM_FUNC_START(ftrace_stub)
+SYM_TYPED_FUNC_START(ftrace_stub)
 	ret
 SYM_FUNC_END(ftrace_stub)
 
+SYM_TYPED_FUNC_START(ftrace_stub_graph)
+	ret
+SYM_FUNC_END(ftrace_stub_graph)
+
 #ifdef CONFIG_FUNCTION_GRAPH_TRACER
 /*
  * void return_to_handler(void)
diff --git a/arch/arm64/kernel/entry.S b/arch/arm64/kernel/entry.S
index 2f69ae43941d..e28137d64b76 100644
--- a/arch/arm64/kernel/entry.S
+++ b/arch/arm64/kernel/entry.S
@@ -37,18 +37,21 @@
 
 	.macro kernel_ventry, el:req, ht:req, regsize:req, label:req
 	.align 7
-#ifdef CONFIG_UNMAP_KERNEL_AT_EL0
+.Lventry_start\@:
 	.if	\el == 0
-alternative_if ARM64_UNMAP_KERNEL_AT_EL0
+	/*
+	 * This must be the first instruction of the EL0 vector entries. It is
+	 * skipped by the trampoline vectors, to trigger the cleanup.
+	 */
+	b	.Lskip_tramp_vectors_cleanup\@
 	.if	\regsize == 64
 	mrs	x30, tpidrro_el0
 	msr	tpidrro_el0, xzr
 	.else
 	mov	x30, xzr
 	.endif
-alternative_else_nop_endif
+.Lskip_tramp_vectors_cleanup\@:
 	.endif
-#endif
 
 	sub	sp, sp, #PT_REGS_SIZE
 #ifdef CONFIG_VMAP_STACK
@@ -95,11 +98,15 @@ alternative_else_nop_endif
 	mrs	x0, tpidrro_el0
 #endif
 	b	el\el\ht\()_\regsize\()_\label
+.org .Lventry_start\@ + 128	// Did we overflow the ventry slot?
 	.endm
 
-	.macro tramp_alias, dst, sym
+	.macro tramp_alias, dst, sym, tmp
 	mov_q	\dst, TRAMP_VALIAS
-	add	\dst, \dst, #(\sym - .entry.tramp.text)
+	adr_l	\tmp, \sym
+	add	\dst, \dst, \tmp
+	adr_l	\tmp, .entry.tramp.text
+	sub	\dst, \dst, \tmp
 	.endm
 
 	/*
@@ -107,7 +114,7 @@ alternative_else_nop_endif
 	 * them if required.
 	 */
 	.macro	apply_ssbd, state, tmp1, tmp2
-alternative_cb	spectre_v4_patch_fw_mitigation_enable
+alternative_cb	ARM64_ALWAYS_SYSTEM, spectre_v4_patch_fw_mitigation_enable
 	b	.L__asm_ssbd_skip\@		// Patched to NOP
 alternative_cb_end
 	ldr_this_cpu	\tmp2, arm64_ssbd_callback_required, \tmp1
@@ -116,7 +123,7 @@ alternative_cb_end
 	tbnz	\tmp2, #TIF_SSBD, .L__asm_ssbd_skip\@
 	mov	w0, #ARM_SMCCC_ARCH_WORKAROUND_2
 	mov	w1, #\state
-alternative_cb	spectre_v4_patch_fw_mitigation_conduit
+alternative_cb	ARM64_ALWAYS_SYSTEM, smccc_patch_fw_mitigation_conduit
 	nop					// Patched to SMC/HVC #0
 alternative_cb_end
 .L__asm_ssbd_skip\@:
@@ -168,7 +175,7 @@ alternative_else_nop_endif
 
 	.macro mte_set_kernel_gcr, tmp, tmp2
 #ifdef CONFIG_KASAN_HW_TAGS
-alternative_cb	kasan_hw_tags_enable
+alternative_cb	ARM64_ALWAYS_SYSTEM, kasan_hw_tags_enable
 	b	1f
 alternative_cb_end
 	mov	\tmp, KERNEL_GCR_EL1
@@ -179,7 +186,7 @@ alternative_cb_end
 
 	.macro mte_set_user_gcr, tsk, tmp, tmp2
 #ifdef CONFIG_KASAN_HW_TAGS
-alternative_cb	kasan_hw_tags_enable
+alternative_cb	ARM64_ALWAYS_SYSTEM, kasan_hw_tags_enable
 	b	1f
 alternative_cb_end
 	ldr	\tmp, [\tsk, #THREAD_MTE_CTRL]
@@ -300,6 +307,7 @@ alternative_else_nop_endif
 	str	w21, [sp, #S_SYSCALLNO]
 	.endif
 
+#ifdef CONFIG_ARM64_PSEUDO_NMI
 	/* Save pmr */
 alternative_if ARM64_HAS_IRQ_PRIO_MASKING
 	mrs_s	x20, SYS_ICC_PMR_EL1
@@ -307,12 +315,6 @@ alternative_if ARM64_HAS_IRQ_PRIO_MASKING
 	mov	x20, #GIC_PRIO_IRQON | GIC_PRIO_PSR_I_SET
 	msr_s	SYS_ICC_PMR_EL1, x20
 alternative_else_nop_endif
-
-	/* Re-enable tag checking (TCO set on exception entry) */
-#ifdef CONFIG_ARM64_MTE
-alternative_if ARM64_MTE
-	SET_PSTATE_TCO(0)
-alternative_else_nop_endif
 #endif
 
 	/*
@@ -330,6 +332,7 @@ alternative_else_nop_endif
 	disable_daif
 	.endif
 
+#ifdef CONFIG_ARM64_PSEUDO_NMI
 	/* Restore pmr */
 alternative_if ARM64_HAS_IRQ_PRIO_MASKING
 	ldr	x20, [sp, #S_PMR_SAVE]
@@ -339,6 +342,7 @@ alternative_if ARM64_HAS_IRQ_PRIO_MASKING
 	dsb	sy				// Ensure priority change is seen by redistributor
 .L__skip_pmr_sync\@:
 alternative_else_nop_endif
+#endif
 
 	ldp	x21, x22, [sp, #S_PC]		// load ELR, SPSR
 
@@ -413,21 +417,26 @@ alternative_else_nop_endif
 	ldp	x24, x25, [sp, #16 * 12]
 	ldp	x26, x27, [sp, #16 * 13]
 	ldp	x28, x29, [sp, #16 * 14]
-	ldr	lr, [sp, #S_LR]
-	add	sp, sp, #PT_REGS_SIZE		// restore sp
 
 	.if	\el == 0
-alternative_insn eret, nop, ARM64_UNMAP_KERNEL_AT_EL0
+alternative_if_not ARM64_UNMAP_KERNEL_AT_EL0
+	ldr	lr, [sp, #S_LR]
+	add	sp, sp, #PT_REGS_SIZE		// restore sp
+	eret
+alternative_else_nop_endif
 #ifdef CONFIG_UNMAP_KERNEL_AT_EL0
 	bne	4f
-	msr	far_el1, x30
-	tramp_alias	x30, tramp_exit_native
+	msr	far_el1, x29
+	tramp_alias	x30, tramp_exit_native, x29
 	br	x30
 4:
-	tramp_alias	x30, tramp_exit_compat
+	tramp_alias	x30, tramp_exit_compat, x29
 	br	x30
 #endif
 	.else
+	ldr	lr, [sp, #S_LR]
+	add	sp, sp, #PT_REGS_SIZE		// restore sp
+
 	/* Ensure any device/NC reads complete */
 	alternative_insn nop, "dmb sy", ARM64_WORKAROUND_1508412
 
@@ -493,7 +502,7 @@ tsk	.req	x28		// current thread_info
 SYM_CODE_START(vectors)
 	kernel_ventry	1, t, 64, sync		// Synchronous EL1t
 	kernel_ventry	1, t, 64, irq		// IRQ EL1t
-	kernel_ventry	1, t, 64, fiq		// FIQ EL1h
+	kernel_ventry	1, t, 64, fiq		// FIQ EL1t
 	kernel_ventry	1, t, 64, error		// Error EL1t
 
 	kernel_ventry	1, h, 64, sync		// Synchronous EL1h
@@ -587,19 +596,13 @@ SYM_CODE_START_LOCAL(ret_to_user)
 	ldr	x19, [tsk, #TSK_TI_FLAGS]	// re-check for single-step
 	enable_step_tsk x19, x2
 #ifdef CONFIG_GCC_PLUGIN_STACKLEAK
-	bl	stackleak_erase
+	bl	stackleak_erase_on_task_stack
 #endif
 	kernel_exit 0
 SYM_CODE_END(ret_to_user)
 
 	.popsection				// .entry.text
 
-#ifdef CONFIG_UNMAP_KERNEL_AT_EL0
-/*
- * Exception vectors trampoline.
- */
-	.pushsection ".entry.tramp.text", "ax"
-
 	// Move from tramp_pg_dir to swapper_pg_dir
 	.macro tramp_map_kernel, tmp
 	mrs	\tmp, ttbr1_el1
@@ -633,12 +636,57 @@ alternative_else_nop_endif
 	 */
 	.endm
 
-	.macro tramp_ventry, regsize = 64
+	.macro		tramp_data_read_var	dst, var
+#ifdef CONFIG_RELOCATABLE
+	ldr		\dst, .L__tramp_data_\var
+	.ifndef		.L__tramp_data_\var
+	.pushsection	".entry.tramp.rodata", "a", %progbits
+	.align		3
+.L__tramp_data_\var:
+	.quad		\var
+	.popsection
+	.endif
+#else
+	/*
+	 * As !RELOCATABLE implies !RANDOMIZE_BASE the address is always a
+	 * compile time constant (and hence not secret and not worth hiding).
+	 *
+	 * As statically allocated kernel code and data always live in the top
+	 * 47 bits of the address space we can sign-extend bit 47 and avoid an
+	 * instruction to load the upper 16 bits (which must be 0xFFFF).
+	 */
+	movz		\dst, :abs_g2_s:\var
+	movk		\dst, :abs_g1_nc:\var
+	movk		\dst, :abs_g0_nc:\var
+#endif
+	.endm
+
+#define BHB_MITIGATION_NONE	0
+#define BHB_MITIGATION_LOOP	1
+#define BHB_MITIGATION_FW	2
+#define BHB_MITIGATION_INSN	3
+
+	.macro tramp_ventry, vector_start, regsize, kpti, bhb
 	.align	7
 1:
 	.if	\regsize == 64
 	msr	tpidrro_el0, x30	// Restored in kernel_ventry
 	.endif
+
+	.if	\bhb == BHB_MITIGATION_LOOP
+	/*
+	 * This sequence must appear before the first indirect branch. i.e. the
+	 * ret out of tramp_ventry. It appears here because x30 is free.
+	 */
+	__mitigate_spectre_bhb_loop	x30
+	.endif // \bhb == BHB_MITIGATION_LOOP
+
+	.if	\bhb == BHB_MITIGATION_INSN
+	clearbhb
+	isb
+	.endif // \bhb == BHB_MITIGATION_INSN
+
+	.if	\kpti == 1
 	/*
 	 * Defend against branch aliasing attacks by pushing a dummy
 	 * entry onto the return stack and using a RET instruction to
@@ -648,46 +696,75 @@ alternative_else_nop_endif
 	b	.
 2:
 	tramp_map_kernel	x30
-#ifdef CONFIG_RANDOMIZE_BASE
-	adr	x30, tramp_vectors + PAGE_SIZE
 alternative_insn isb, nop, ARM64_WORKAROUND_QCOM_FALKOR_E1003
-	ldr	x30, [x30]
-#else
-	ldr	x30, =vectors
-#endif
+	tramp_data_read_var	x30, vectors
 alternative_if_not ARM64_WORKAROUND_CAVIUM_TX2_219_PRFM
-	prfm	plil1strm, [x30, #(1b - tramp_vectors)]
+	prfm	plil1strm, [x30, #(1b - \vector_start)]
 alternative_else_nop_endif
+
 	msr	vbar_el1, x30
-	add	x30, x30, #(1b - tramp_vectors)
 	isb
+	.else
+	adr_l	x30, vectors
+	.endif // \kpti == 1
+
+	.if	\bhb == BHB_MITIGATION_FW
+	/*
+	 * The firmware sequence must appear before the first indirect branch.
+	 * i.e. the ret out of tramp_ventry. But it also needs the stack to be
+	 * mapped to save/restore the registers the SMC clobbers.
+	 */
+	__mitigate_spectre_bhb_fw
+	.endif // \bhb == BHB_MITIGATION_FW
+
+	add	x30, x30, #(1b - \vector_start + 4)
 	ret
+.org 1b + 128	// Did we overflow the ventry slot?
 	.endm
 
 	.macro tramp_exit, regsize = 64
-	adr	x30, tramp_vectors
+	tramp_data_read_var	x30, this_cpu_vector
+	get_this_cpu_offset x29
+	ldr	x30, [x30, x29]
+
 	msr	vbar_el1, x30
-	tramp_unmap_kernel	x30
+	ldr	lr, [sp, #S_LR]
+	tramp_unmap_kernel	x29
 	.if	\regsize == 64
-	mrs	x30, far_el1
+	mrs	x29, far_el1
 	.endif
+	add	sp, sp, #PT_REGS_SIZE		// restore sp
 	eret
 	sb
 	.endm
 
-	.align	11
-SYM_CODE_START_NOALIGN(tramp_vectors)
+	.macro	generate_tramp_vector,	kpti, bhb
+.Lvector_start\@:
 	.space	0x400
 
-	tramp_ventry
-	tramp_ventry
-	tramp_ventry
-	tramp_ventry
+	.rept	4
+	tramp_ventry	.Lvector_start\@, 64, \kpti, \bhb
+	.endr
+	.rept	4
+	tramp_ventry	.Lvector_start\@, 32, \kpti, \bhb
+	.endr
+	.endm
 
-	tramp_ventry	32
-	tramp_ventry	32
-	tramp_ventry	32
-	tramp_ventry	32
+#ifdef CONFIG_UNMAP_KERNEL_AT_EL0
+/*
+ * Exception vectors trampoline.
+ * The order must match __bp_harden_el1_vectors and the
+ * arm64_bp_harden_el1_vectors enum.
+ */
+	.pushsection ".entry.tramp.text", "ax"
+	.align	11
+SYM_CODE_START_NOALIGN(tramp_vectors)
+#ifdef CONFIG_MITIGATE_SPECTRE_BRANCH_HISTORY
+	generate_tramp_vector	kpti=1, bhb=BHB_MITIGATION_LOOP
+	generate_tramp_vector	kpti=1, bhb=BHB_MITIGATION_FW
+	generate_tramp_vector	kpti=1, bhb=BHB_MITIGATION_INSN
+#endif /* CONFIG_MITIGATE_SPECTRE_BRANCH_HISTORY */
+	generate_tramp_vector	kpti=1, bhb=BHB_MITIGATION_NONE
 SYM_CODE_END(tramp_vectors)
 
 SYM_CODE_START(tramp_exit_native)
@@ -697,20 +774,47 @@ SYM_CODE_END(tramp_exit_native)
 SYM_CODE_START(tramp_exit_compat)
 	tramp_exit	32
 SYM_CODE_END(tramp_exit_compat)
-
-	.ltorg
 	.popsection				// .entry.tramp.text
-#ifdef CONFIG_RANDOMIZE_BASE
-	.pushsection ".rodata", "a"
-	.align PAGE_SHIFT
-SYM_DATA_START(__entry_tramp_data_start)
-	.quad	vectors
-SYM_DATA_END(__entry_tramp_data_start)
-	.popsection				// .rodata
-#endif /* CONFIG_RANDOMIZE_BASE */
 #endif /* CONFIG_UNMAP_KERNEL_AT_EL0 */
 
 /*
+ * Exception vectors for spectre mitigations on entry from EL1 when
+ * kpti is not in use.
+ */
+	.macro generate_el1_vector, bhb
+.Lvector_start\@:
+	kernel_ventry	1, t, 64, sync		// Synchronous EL1t
+	kernel_ventry	1, t, 64, irq		// IRQ EL1t
+	kernel_ventry	1, t, 64, fiq		// FIQ EL1h
+	kernel_ventry	1, t, 64, error		// Error EL1t
+
+	kernel_ventry	1, h, 64, sync		// Synchronous EL1h
+	kernel_ventry	1, h, 64, irq		// IRQ EL1h
+	kernel_ventry	1, h, 64, fiq		// FIQ EL1h
+	kernel_ventry	1, h, 64, error		// Error EL1h
+
+	.rept	4
+	tramp_ventry	.Lvector_start\@, 64, 0, \bhb
+	.endr
+	.rept 4
+	tramp_ventry	.Lvector_start\@, 32, 0, \bhb
+	.endr
+	.endm
+
+/* The order must match tramp_vecs and the arm64_bp_harden_el1_vectors enum. */
+	.pushsection ".entry.text", "ax"
+	.align	11
+SYM_CODE_START(__bp_harden_el1_vectors)
+#ifdef CONFIG_MITIGATE_SPECTRE_BRANCH_HISTORY
+	generate_el1_vector	bhb=BHB_MITIGATION_LOOP
+	generate_el1_vector	bhb=BHB_MITIGATION_FW
+	generate_el1_vector	bhb=BHB_MITIGATION_INSN
+#endif /* CONFIG_MITIGATE_SPECTRE_BRANCH_HISTORY */
+SYM_CODE_END(__bp_harden_el1_vectors)
+	.popsection
+
+
+/*
  * Register switch for AArch64. The callee-saved registers need to be saved
  * and restored. On entry:
  *   x0 = previous task_struct (must be preserved across the switch)
@@ -821,7 +925,6 @@ NOKPROBE(call_on_irq_stack)
  * This clobbers x4, __sdei_handler() will restore this from firmware's
  * copy.
  */
-.ltorg
 .pushsection ".entry.tramp.text", "ax"
 SYM_CODE_START(__sdei_asm_entry_trampoline)
 	mrs	x4, ttbr1_el1
@@ -835,14 +938,7 @@ SYM_CODE_START(__sdei_asm_entry_trampoline)
 	 * Remember whether to unmap the kernel on exit.
 	 */
 1:	str	x4, [x1, #(SDEI_EVENT_INTREGS + S_SDEI_TTBR1)]
-
-#ifdef CONFIG_RANDOMIZE_BASE
-	adr	x4, tramp_vectors + PAGE_SIZE
-	add	x4, x4, #:lo12:__sdei_asm_trampoline_next_handler
-	ldr	x4, [x4]
-#else
-	ldr	x4, =__sdei_asm_handler
-#endif
+	tramp_data_read_var     x4, __sdei_asm_handler
 	br	x4
 SYM_CODE_END(__sdei_asm_entry_trampoline)
 NOKPROBE(__sdei_asm_entry_trampoline)
@@ -863,15 +959,7 @@ SYM_CODE_START(__sdei_asm_exit_trampoline)
 1:	sdei_handler_exit exit_mode=x2
 SYM_CODE_END(__sdei_asm_exit_trampoline)
 NOKPROBE(__sdei_asm_exit_trampoline)
-	.ltorg
 .popsection		// .entry.tramp.text
-#ifdef CONFIG_RANDOMIZE_BASE
-.pushsection ".rodata", "a"
-SYM_DATA_START(__sdei_asm_trampoline_next_handler)
-	.quad	__sdei_asm_handler
-SYM_DATA_END(__sdei_asm_trampoline_next_handler)
-.popsection		// .rodata
-#endif /* CONFIG_RANDOMIZE_BASE */
 #endif /* CONFIG_UNMAP_KERNEL_AT_EL0 */
 
 /*
@@ -966,8 +1054,10 @@ SYM_CODE_START(__sdei_asm_handler)
 	mov	sp, x1
 
 	mov	x1, x0			// address to complete_and_resume
-	/* x0 = (x0 <= 1) ? EVENT_COMPLETE:EVENT_COMPLETE_AND_RESUME */
-	cmp	x0, #1
+	/* x0 = (x0 <= SDEI_EV_FAILED) ?
+	 * EVENT_COMPLETE:EVENT_COMPLETE_AND_RESUME
+	 */
+	cmp	x0, #SDEI_EV_FAILED
 	mov_q	x2, SDEI_1_0_FN_SDEI_EVENT_COMPLETE
 	mov_q	x3, SDEI_1_0_FN_SDEI_EVENT_COMPLETE_AND_RESUME
 	csel	x0, x2, x3, ls
@@ -979,7 +1069,7 @@ alternative_if_not ARM64_UNMAP_KERNEL_AT_EL0
 alternative_else_nop_endif
 
 #ifdef CONFIG_UNMAP_KERNEL_AT_EL0
-	tramp_alias	dst=x5, sym=__sdei_asm_exit_trampoline
+	tramp_alias	dst=x5, sym=__sdei_asm_exit_trampoline, tmp=x3
 	br	x5
 #endif
 SYM_CODE_END(__sdei_asm_handler)
diff --git a/arch/arm64/kernel/fpsimd.c b/arch/arm64/kernel/fpsimd.c
index fa244c426f61..23834d96d1e7 100644
--- a/arch/arm64/kernel/fpsimd.c
+++ b/arch/arm64/kernel/fpsimd.c
@@ -15,6 +15,7 @@
 #include <linux/compiler.h>
 #include <linux/cpu.h>
 #include <linux/cpu_pm.h>
+#include <linux/ctype.h>
 #include <linux/kernel.h>
 #include <linux/linkage.h>
 #include <linux/irqflags.h>
@@ -78,7 +79,11 @@
  * indicate whether or not the userland FPSIMD state of the current task is
  * present in the registers. The flag is set unless the FPSIMD registers of this
  * CPU currently contain the most recent userland FPSIMD state of the current
- * task.
+ * task. If the task is behaving as a VMM, then this is will be managed by
+ * KVM which will clear it to indicate that the vcpu FPSIMD state is currently
+ * loaded on the CPU, allowing the state to be saved if a FPSIMD-aware
+ * softirq kicks in. Upon vcpu_put(), KVM will save the vcpu FP state and
+ * flag the register state as invalid.
  *
  * In order to allow softirq handlers to use FPSIMD, kernel_neon_begin() may
  * save the task's FPSIMD context back to task_struct from softirq context.
@@ -116,7 +121,10 @@
 struct fpsimd_last_state_struct {
 	struct user_fpsimd_state *st;
 	void *sve_state;
+	void *za_state;
+	u64 *svcr;
 	unsigned int sve_vl;
+	unsigned int sme_vl;
 };
 
 static DEFINE_PER_CPU(struct fpsimd_last_state_struct, fpsimd_last_state);
@@ -131,6 +139,12 @@ __ro_after_init struct vl_info vl_info[ARM64_VEC_MAX] = {
 		.max_virtualisable_vl	= SVE_VL_MIN,
 	},
 #endif
+#ifdef CONFIG_ARM64_SME
+	[ARM64_VEC_SME] = {
+		.type			= ARM64_VEC_SME,
+		.name			= "SME",
+	},
+#endif
 };
 
 static unsigned int vec_vl_inherit_flag(enum vec_type type)
@@ -138,6 +152,8 @@ static unsigned int vec_vl_inherit_flag(enum vec_type type)
 	switch (type) {
 	case ARM64_VEC_SVE:
 		return TIF_SVE_VL_INHERIT;
+	case ARM64_VEC_SME:
+		return TIF_SME_VL_INHERIT;
 	default:
 		WARN_ON_ONCE(1);
 		return 0;
@@ -181,6 +197,26 @@ extern void __percpu *efi_sve_state;
 
 #endif /* ! CONFIG_ARM64_SVE */
 
+#ifdef CONFIG_ARM64_SME
+
+static int get_sme_default_vl(void)
+{
+	return get_default_vl(ARM64_VEC_SME);
+}
+
+static void set_sme_default_vl(int val)
+{
+	set_default_vl(ARM64_VEC_SME, val);
+}
+
+static void sme_free(struct task_struct *);
+
+#else
+
+static inline void sme_free(struct task_struct *t) { }
+
+#endif
+
 DEFINE_PER_CPU(bool, fpsimd_context_busy);
 EXPORT_PER_CPU_SYMBOL(fpsimd_context_busy);
 
@@ -201,10 +237,19 @@ static void __get_cpu_fpsimd_context(void)
  *
  * The double-underscore version must only be called if you know the task
  * can't be preempted.
+ *
+ * On RT kernels local_bh_disable() is not sufficient because it only
+ * serializes soft interrupt related sections via a local lock, but stays
+ * preemptible. Disabling preemption is the right choice here as bottom
+ * half processing is always in thread context on RT kernels so it
+ * implicitly prevents bottom half processing as well.
  */
 static void get_cpu_fpsimd_context(void)
 {
-	local_bh_disable();
+	if (!IS_ENABLED(CONFIG_PREEMPT_RT))
+		local_bh_disable();
+	else
+		preempt_disable();
 	__get_cpu_fpsimd_context();
 }
 
@@ -225,7 +270,10 @@ static void __put_cpu_fpsimd_context(void)
 static void put_cpu_fpsimd_context(void)
 {
 	__put_cpu_fpsimd_context();
-	local_bh_enable();
+	if (!IS_ENABLED(CONFIG_PREEMPT_RT))
+		local_bh_enable();
+	else
+		preempt_enable();
 }
 
 static bool have_cpu_fpsimd_context(void)
@@ -233,23 +281,6 @@ static bool have_cpu_fpsimd_context(void)
 	return !preemptible() && __this_cpu_read(fpsimd_context_busy);
 }
 
-/*
- * Call __sve_free() directly only if you know task can't be scheduled
- * or preempted.
- */
-static void __sve_free(struct task_struct *task)
-{
-	kfree(task->thread.sve_state);
-	task->thread.sve_state = NULL;
-}
-
-static void sve_free(struct task_struct *task)
-{
-	WARN_ON(test_tsk_thread_flag(task, TIF_SVE));
-
-	__sve_free(task);
-}
-
 unsigned int task_get_vl(const struct task_struct *task, enum vec_type type)
 {
 	return task->thread.vl[type];
@@ -274,24 +305,36 @@ void task_set_vl_onexec(struct task_struct *task, enum vec_type type,
 }
 
 /*
+ * TIF_SME controls whether a task can use SME without trapping while
+ * in userspace, when TIF_SME is set then we must have storage
+ * alocated in sve_state and za_state to store the contents of both ZA
+ * and the SVE registers for both streaming and non-streaming modes.
+ *
+ * If both SVCR.ZA and SVCR.SM are disabled then at any point we
+ * may disable TIF_SME and reenable traps.
+ */
+
+
+/*
  * TIF_SVE controls whether a task can use SVE without trapping while
- * in userspace, and also the way a task's FPSIMD/SVE state is stored
- * in thread_struct.
+ * in userspace, and also (together with TIF_SME) the way a task's
+ * FPSIMD/SVE state is stored in thread_struct.
  *
  * The kernel uses this flag to track whether a user task is actively
  * using SVE, and therefore whether full SVE register state needs to
  * be tracked.  If not, the cheaper FPSIMD context handling code can
  * be used instead of the more costly SVE equivalents.
  *
- *  * TIF_SVE set:
+ *  * TIF_SVE or SVCR.SM set:
  *
  *    The task can execute SVE instructions while in userspace without
  *    trapping to the kernel.
  *
  *    When stored, Z0-Z31 (incorporating Vn in bits[127:0] or the
- *    corresponding Zn), P0-P15 and FFR are encoded in in
+ *    corresponding Zn), P0-P15 and FFR are encoded in
  *    task->thread.sve_state, formatted appropriately for vector
- *    length task->thread.sve_vl.
+ *    length task->thread.sve_vl or, if SVCR.SM is set,
+ *    task->thread.sme_vl.
  *
  *    task->thread.sve_state must point to a valid buffer at least
  *    sve_state_size(task) bytes in size.
@@ -329,27 +372,64 @@ void task_set_vl_onexec(struct task_struct *task, enum vec_type type,
  */
 static void task_fpsimd_load(void)
 {
+	bool restore_sve_regs = false;
+	bool restore_ffr;
+
 	WARN_ON(!system_supports_fpsimd());
 	WARN_ON(!have_cpu_fpsimd_context());
 
+	/* Check if we should restore SVE first */
 	if (IS_ENABLED(CONFIG_ARM64_SVE) && test_thread_flag(TIF_SVE)) {
 		sve_set_vq(sve_vq_from_vl(task_get_sve_vl(current)) - 1);
+		restore_sve_regs = true;
+		restore_ffr = true;
+	}
+
+	/* Restore SME, override SVE register configuration if needed */
+	if (system_supports_sme()) {
+		unsigned long sme_vl = task_get_sme_vl(current);
+
+		/* Ensure VL is set up for restoring data */
+		if (test_thread_flag(TIF_SME))
+			sme_set_vq(sve_vq_from_vl(sme_vl) - 1);
+
+		write_sysreg_s(current->thread.svcr, SYS_SVCR);
+
+		if (thread_za_enabled(&current->thread))
+			za_load_state(current->thread.za_state);
+
+		if (thread_sm_enabled(&current->thread)) {
+			restore_sve_regs = true;
+			restore_ffr = system_supports_fa64();
+		}
+	}
+
+	if (restore_sve_regs)
 		sve_load_state(sve_pffr(&current->thread),
-			       &current->thread.uw.fpsimd_state.fpsr, true);
-	} else {
+			       &current->thread.uw.fpsimd_state.fpsr,
+			       restore_ffr);
+	else
 		fpsimd_load_state(&current->thread.uw.fpsimd_state);
-	}
 }
 
 /*
  * Ensure FPSIMD/SVE storage in memory for the loaded context is up to
- * date with respect to the CPU registers.
+ * date with respect to the CPU registers. Note carefully that the
+ * current context is the context last bound to the CPU stored in
+ * last, if KVM is involved this may be the guest VM context rather
+ * than the host thread for the VM pointed to by current. This means
+ * that we must always reference the state storage via last rather
+ * than via current, other than the TIF_ flags which KVM will
+ * carefully maintain for us.
  */
 static void fpsimd_save(void)
 {
 	struct fpsimd_last_state_struct const *last =
 		this_cpu_ptr(&fpsimd_last_state);
 	/* set by fpsimd_bind_task_to_cpu() or fpsimd_bind_state_to_cpu() */
+	bool save_sve_regs = false;
+	bool save_ffr;
+	unsigned int vl;
 
 	WARN_ON(!system_supports_fpsimd());
 	WARN_ON(!have_cpu_fpsimd_context());
@@ -357,9 +437,31 @@ static void fpsimd_save(void)
 	if (test_thread_flag(TIF_FOREIGN_FPSTATE))
 		return;
 
-	if (IS_ENABLED(CONFIG_ARM64_SVE) &&
-	    test_thread_flag(TIF_SVE)) {
-		if (WARN_ON(sve_get_vl() != last->sve_vl)) {
+	if (test_thread_flag(TIF_SVE)) {
+		save_sve_regs = true;
+		save_ffr = true;
+		vl = last->sve_vl;
+	}
+
+	if (system_supports_sme()) {
+		u64 *svcr = last->svcr;
+
+		*svcr = read_sysreg_s(SYS_SVCR);
+
+		if (*svcr & SVCR_ZA_MASK)
+			za_save_state(last->za_state);
+
+		/* If we are in streaming mode override regular SVE. */
+		if (*svcr & SVCR_SM_MASK) {
+			save_sve_regs = true;
+			save_ffr = system_supports_fa64();
+			vl = last->sme_vl;
+		}
+	}
+
+	if (IS_ENABLED(CONFIG_ARM64_SVE) && save_sve_regs) {
+		/* Get the configured VL from RDVL, will account for SM */
+		if (WARN_ON(sve_get_vl() != vl)) {
 			/*
 			 * Can't save the user regs, so current would
 			 * re-enter user with corrupt state.
@@ -370,8 +472,8 @@ static void fpsimd_save(void)
 		}
 
 		sve_save_state((char *)last->sve_state +
-					sve_ffr_offset(last->sve_vl),
-			       &last->st->fpsr, true);
+					sve_ffr_offset(vl),
+			       &last->st->fpsr, save_ffr);
 	} else {
 		fpsimd_save_state(last->st);
 	}
@@ -398,6 +500,8 @@ static unsigned int find_supported_vector_length(enum vec_type type,
 
 	if (vl > max_vl)
 		vl = max_vl;
+	if (vl < info->min_vl)
+		vl = info->min_vl;
 
 	bit = find_next_bit(info->vq_map, SVE_VQ_MAX,
 			    __vq_to_bit(sve_vq_from_vl(vl)));
@@ -406,12 +510,13 @@ static unsigned int find_supported_vector_length(enum vec_type type,
 
 #if defined(CONFIG_ARM64_SVE) && defined(CONFIG_SYSCTL)
 
-static int sve_proc_do_default_vl(struct ctl_table *table, int write,
+static int vec_proc_do_default_vl(struct ctl_table *table, int write,
 				  void *buffer, size_t *lenp, loff_t *ppos)
 {
-	struct vl_info *info = &vl_info[ARM64_VEC_SVE];
+	struct vl_info *info = table->extra1;
+	enum vec_type type = info->type;
 	int ret;
-	int vl = get_sve_default_vl();
+	int vl = get_default_vl(type);
 	struct ctl_table tmp_table = {
 		.data = &vl,
 		.maxlen = sizeof(vl),
@@ -428,7 +533,7 @@ static int sve_proc_do_default_vl(struct ctl_table *table, int write,
 	if (!sve_vl_valid(vl))
 		return -EINVAL;
 
-	set_sve_default_vl(find_supported_vector_length(ARM64_VEC_SVE, vl));
+	set_default_vl(type, find_supported_vector_length(type, vl));
 	return 0;
 }
 
@@ -436,7 +541,8 @@ static struct ctl_table sve_default_vl_table[] = {
 	{
 		.procname	= "sve_default_vector_length",
 		.mode		= 0644,
-		.proc_handler	= sve_proc_do_default_vl,
+		.proc_handler	= vec_proc_do_default_vl,
+		.extra1		= &vl_info[ARM64_VEC_SVE],
 	},
 	{ }
 };
@@ -454,6 +560,30 @@ static int __init sve_sysctl_init(void)
 static int __init sve_sysctl_init(void) { return 0; }
 #endif /* ! (CONFIG_ARM64_SVE && CONFIG_SYSCTL) */
 
+#if defined(CONFIG_ARM64_SME) && defined(CONFIG_SYSCTL)
+static struct ctl_table sme_default_vl_table[] = {
+	{
+		.procname	= "sme_default_vector_length",
+		.mode		= 0644,
+		.proc_handler	= vec_proc_do_default_vl,
+		.extra1		= &vl_info[ARM64_VEC_SME],
+	},
+	{ }
+};
+
+static int __init sme_sysctl_init(void)
+{
+	if (system_supports_sme())
+		if (!register_sysctl("abi", sme_default_vl_table))
+			return -EINVAL;
+
+	return 0;
+}
+
+#else /* ! (CONFIG_ARM64_SME && CONFIG_SYSCTL) */
+static int __init sme_sysctl_init(void) { return 0; }
+#endif /* ! (CONFIG_ARM64_SME && CONFIG_SYSCTL) */
+
 #define ZREG(sve_state, vq, n) ((char *)(sve_state) +		\
 	(SVE_SIG_ZREG_OFFSET(vq, n) - SVE_SIG_REGS_OFFSET))
 
@@ -507,7 +637,7 @@ static void fpsimd_to_sve(struct task_struct *task)
 	if (!system_supports_sve())
 		return;
 
-	vq = sve_vq_from_vl(task_get_sve_vl(task));
+	vq = sve_vq_from_vl(thread_get_cur_vl(&task->thread));
 	__fpsimd_to_sve(sst, fst, vq);
 }
 
@@ -524,7 +654,7 @@ static void fpsimd_to_sve(struct task_struct *task)
  */
 static void sve_to_fpsimd(struct task_struct *task)
 {
-	unsigned int vq;
+	unsigned int vq, vl;
 	void const *sst = task->thread.sve_state;
 	struct user_fpsimd_state *fst = &task->thread.uw.fpsimd_state;
 	unsigned int i;
@@ -533,7 +663,8 @@ static void sve_to_fpsimd(struct task_struct *task)
 	if (!system_supports_sve())
 		return;
 
-	vq = sve_vq_from_vl(task_get_sve_vl(task));
+	vl = thread_get_cur_vl(&task->thread);
+	vq = sve_vq_from_vl(vl);
 	for (i = 0; i < SVE_NUM_ZREGS; ++i) {
 		p = (__uint128_t const *)ZREG(sst, vq, i);
 		fst->vregs[i] = arm64_le128_to_cpu(*p);
@@ -541,14 +672,37 @@ static void sve_to_fpsimd(struct task_struct *task)
 }
 
 #ifdef CONFIG_ARM64_SVE
+/*
+ * Call __sve_free() directly only if you know task can't be scheduled
+ * or preempted.
+ */
+static void __sve_free(struct task_struct *task)
+{
+	kfree(task->thread.sve_state);
+	task->thread.sve_state = NULL;
+}
+
+static void sve_free(struct task_struct *task)
+{
+	WARN_ON(test_tsk_thread_flag(task, TIF_SVE));
+
+	__sve_free(task);
+}
 
 /*
  * Return how many bytes of memory are required to store the full SVE
  * state for task, given task's currently configured vector length.
  */
-static size_t sve_state_size(struct task_struct const *task)
+size_t sve_state_size(struct task_struct const *task)
 {
-	return SVE_SIG_REGS_SIZE(sve_vq_from_vl(task_get_sve_vl(task)));
+	unsigned int vl = 0;
+
+	if (system_supports_sve())
+		vl = task_get_sve_vl(task);
+	if (system_supports_sme())
+		vl = max(vl, task_get_sme_vl(task));
+
+	return SVE_SIG_REGS_SIZE(sve_vq_from_vl(vl));
 }
 
 /*
@@ -561,10 +715,12 @@ static size_t sve_state_size(struct task_struct const *task)
  * do_sve_acc() case, there is no ABI requirement to hide stale data
  * written previously be task.
  */
-void sve_alloc(struct task_struct *task)
+void sve_alloc(struct task_struct *task, bool flush)
 {
 	if (task->thread.sve_state) {
-		memset(task->thread.sve_state, 0, sve_state_size(task));
+		if (flush)
+			memset(task->thread.sve_state, 0,
+			       sve_state_size(task));
 		return;
 	}
 
@@ -575,6 +731,19 @@ void sve_alloc(struct task_struct *task)
 
 
 /*
+ * Force the FPSIMD state shared with SVE to be updated in the SVE state
+ * even if the SVE state is the current active state.
+ *
+ * This should only be called by ptrace.  task must be non-runnable.
+ * task->thread.sve_state must point to at least sve_state_size(task)
+ * bytes of allocated kernel memory.
+ */
+void fpsimd_force_sync_to_sve(struct task_struct *task)
+{
+	fpsimd_to_sve(task);
+}
+
+/*
  * Ensure that task->thread.sve_state is up to date with respect to
  * the user task, irrespective of when SVE is in use or not.
  *
@@ -584,7 +753,8 @@ void sve_alloc(struct task_struct *task)
  */
 void fpsimd_sync_to_sve(struct task_struct *task)
 {
-	if (!test_tsk_thread_flag(task, TIF_SVE))
+	if (!test_tsk_thread_flag(task, TIF_SVE) &&
+	    !thread_sm_enabled(&task->thread))
 		fpsimd_to_sve(task);
 }
 
@@ -598,7 +768,8 @@ void fpsimd_sync_to_sve(struct task_struct *task)
  */
 void sve_sync_to_fpsimd(struct task_struct *task)
 {
-	if (test_tsk_thread_flag(task, TIF_SVE))
+	if (test_tsk_thread_flag(task, TIF_SVE) ||
+	    thread_sm_enabled(&task->thread))
 		sve_to_fpsimd(task);
 }
 
@@ -623,13 +794,13 @@ void sve_sync_from_fpsimd_zeropad(struct task_struct *task)
 	if (!test_tsk_thread_flag(task, TIF_SVE))
 		return;
 
-	vq = sve_vq_from_vl(task_get_sve_vl(task));
+	vq = sve_vq_from_vl(thread_get_cur_vl(&task->thread));
 
 	memset(sst, 0, SVE_SIG_REGS_SIZE(vq));
 	__fpsimd_to_sve(sst, fst, vq);
 }
 
-int sve_set_vector_length(struct task_struct *task,
+int vec_set_vector_length(struct task_struct *task, enum vec_type type,
 			  unsigned long vl, unsigned long flags)
 {
 	if (flags & ~(unsigned long)(PR_SVE_VL_INHERIT |
@@ -640,33 +811,34 @@ int sve_set_vector_length(struct task_struct *task,
 		return -EINVAL;
 
 	/*
-	 * Clamp to the maximum vector length that VL-agnostic SVE code can
-	 * work with.  A flag may be assigned in the future to allow setting
-	 * of larger vector lengths without confusing older software.
+	 * Clamp to the maximum vector length that VL-agnostic code
+	 * can work with.  A flag may be assigned in the future to
+	 * allow setting of larger vector lengths without confusing
+	 * older software.
 	 */
-	if (vl > SVE_VL_ARCH_MAX)
-		vl = SVE_VL_ARCH_MAX;
+	if (vl > VL_ARCH_MAX)
+		vl = VL_ARCH_MAX;
 
-	vl = find_supported_vector_length(ARM64_VEC_SVE, vl);
+	vl = find_supported_vector_length(type, vl);
 
 	if (flags & (PR_SVE_VL_INHERIT |
 		     PR_SVE_SET_VL_ONEXEC))
-		task_set_sve_vl_onexec(task, vl);
+		task_set_vl_onexec(task, type, vl);
 	else
 		/* Reset VL to system default on next exec: */
-		task_set_sve_vl_onexec(task, 0);
+		task_set_vl_onexec(task, type, 0);
 
 	/* Only actually set the VL if not deferred: */
 	if (flags & PR_SVE_SET_VL_ONEXEC)
 		goto out;
 
-	if (vl == task_get_sve_vl(task))
+	if (vl == task_get_vl(task, type))
 		goto out;
 
 	/*
 	 * To ensure the FPSIMD bits of the SVE vector registers are preserved,
 	 * write any live register state back to task_struct, and convert to a
-	 * non-SVE thread.
+	 * regular FPSIMD thread.
 	 */
 	if (task == current) {
 		get_cpu_fpsimd_context();
@@ -675,22 +847,31 @@ int sve_set_vector_length(struct task_struct *task,
 	}
 
 	fpsimd_flush_task_state(task);
-	if (test_and_clear_tsk_thread_flag(task, TIF_SVE))
+	if (test_and_clear_tsk_thread_flag(task, TIF_SVE) ||
+	    thread_sm_enabled(&task->thread))
 		sve_to_fpsimd(task);
 
+	if (system_supports_sme() && type == ARM64_VEC_SME) {
+		task->thread.svcr &= ~(SVCR_SM_MASK |
+				       SVCR_ZA_MASK);
+		clear_thread_flag(TIF_SME);
+	}
+
 	if (task == current)
 		put_cpu_fpsimd_context();
 
 	/*
-	 * Force reallocation of task SVE state to the correct size
-	 * on next use:
+	 * Force reallocation of task SVE and SME state to the correct
+	 * size on next use:
 	 */
 	sve_free(task);
+	if (system_supports_sme() && type == ARM64_VEC_SME)
+		sme_free(task);
 
-	task_set_sve_vl(task, vl);
+	task_set_vl(task, type, vl);
 
 out:
-	update_tsk_thread_flag(task, TIF_SVE_VL_INHERIT,
+	update_tsk_thread_flag(task, vec_vl_inherit_flag(type),
 			       flags & PR_SVE_VL_INHERIT);
 
 	return 0;
@@ -698,20 +879,21 @@ out:
 
 /*
  * Encode the current vector length and flags for return.
- * This is only required for prctl(): ptrace has separate fields
+ * This is only required for prctl(): ptrace has separate fields.
+ * SVE and SME use the same bits for _ONEXEC and _INHERIT.
  *
- * flags are as for sve_set_vector_length().
+ * flags are as for vec_set_vector_length().
  */
-static int sve_prctl_status(unsigned long flags)
+static int vec_prctl_status(enum vec_type type, unsigned long flags)
 {
 	int ret;
 
 	if (flags & PR_SVE_SET_VL_ONEXEC)
-		ret = task_get_sve_vl_onexec(current);
+		ret = task_get_vl_onexec(current, type);
 	else
-		ret = task_get_sve_vl(current);
+		ret = task_get_vl(current, type);
 
-	if (test_thread_flag(TIF_SVE_VL_INHERIT))
+	if (test_thread_flag(vec_vl_inherit_flag(type)))
 		ret |= PR_SVE_VL_INHERIT;
 
 	return ret;
@@ -729,11 +911,11 @@ int sve_set_current_vl(unsigned long arg)
 	if (!system_supports_sve() || is_compat_task())
 		return -EINVAL;
 
-	ret = sve_set_vector_length(current, vl, flags);
+	ret = vec_set_vector_length(current, ARM64_VEC_SVE, vl, flags);
 	if (ret)
 		return ret;
 
-	return sve_prctl_status(flags);
+	return vec_prctl_status(ARM64_VEC_SVE, flags);
 }
 
 /* PR_SVE_GET_VL */
@@ -742,9 +924,39 @@ int sve_get_current_vl(void)
 	if (!system_supports_sve() || is_compat_task())
 		return -EINVAL;
 
-	return sve_prctl_status(0);
+	return vec_prctl_status(ARM64_VEC_SVE, 0);
+}
+
+#ifdef CONFIG_ARM64_SME
+/* PR_SME_SET_VL */
+int sme_set_current_vl(unsigned long arg)
+{
+	unsigned long vl, flags;
+	int ret;
+
+	vl = arg & PR_SME_VL_LEN_MASK;
+	flags = arg & ~vl;
+
+	if (!system_supports_sme() || is_compat_task())
+		return -EINVAL;
+
+	ret = vec_set_vector_length(current, ARM64_VEC_SME, vl, flags);
+	if (ret)
+		return ret;
+
+	return vec_prctl_status(ARM64_VEC_SME, flags);
 }
 
+/* PR_SME_GET_VL */
+int sme_get_current_vl(void)
+{
+	if (!system_supports_sme() || is_compat_task())
+		return -EINVAL;
+
+	return vec_prctl_status(ARM64_VEC_SME, 0);
+}
+#endif /* CONFIG_ARM64_SME */
+
 static void vec_probe_vqs(struct vl_info *info,
 			  DECLARE_BITMAP(map, SVE_VQ_MAX))
 {
@@ -754,7 +966,23 @@ static void vec_probe_vqs(struct vl_info *info,
 
 	for (vq = SVE_VQ_MAX; vq >= SVE_VQ_MIN; --vq) {
 		write_vl(info->type, vq - 1); /* self-syncing */
-		vl = sve_get_vl();
+
+		switch (info->type) {
+		case ARM64_VEC_SVE:
+			vl = sve_get_vl();
+			break;
+		case ARM64_VEC_SME:
+			vl = sme_get_vl();
+			break;
+		default:
+			vl = 0;
+			break;
+		}
+
+		/* Minimum VL identified? */
+		if (sve_vq_from_vl(vl) > vq)
+			break;
+
 		vq = sve_vq_from_vl(vl); /* skip intervening lengths */
 		set_bit(__vq_to_bit(vq), map);
 	}
@@ -840,21 +1068,25 @@ int vec_verify_vq_map(enum vec_type type)
 
 static void __init sve_efi_setup(void)
 {
-	struct vl_info *info = &vl_info[ARM64_VEC_SVE];
+	int max_vl = 0;
+	int i;
 
 	if (!IS_ENABLED(CONFIG_EFI))
 		return;
 
+	for (i = 0; i < ARRAY_SIZE(vl_info); i++)
+		max_vl = max(vl_info[i].max_vl, max_vl);
+
 	/*
 	 * alloc_percpu() warns and prints a backtrace if this goes wrong.
 	 * This is evidence of a crippled system and we are returning void,
 	 * so no attempt is made to handle this situation here.
 	 */
-	if (!sve_vl_valid(info->max_vl))
+	if (!sve_vl_valid(max_vl))
 		goto fail;
 
 	efi_sve_state = __alloc_percpu(
-		SVE_SIG_REGS_SIZE(sve_vq_from_vl(info->max_vl)), SVE_VQ_BYTES);
+		SVE_SIG_REGS_SIZE(sve_vq_from_vl(max_vl)), SVE_VQ_BYTES);
 	if (!efi_sve_state)
 		goto fail;
 
@@ -973,10 +1205,172 @@ void __init sve_setup(void)
 void fpsimd_release_task(struct task_struct *dead_task)
 {
 	__sve_free(dead_task);
+	sme_free(dead_task);
 }
 
 #endif /* CONFIG_ARM64_SVE */
 
+#ifdef CONFIG_ARM64_SME
+
+/*
+ * Ensure that task->thread.za_state is allocated and sufficiently large.
+ *
+ * This function should be used only in preparation for replacing
+ * task->thread.za_state with new data.  The memory is always zeroed
+ * here to prevent stale data from showing through: this is done in
+ * the interest of testability and predictability, the architecture
+ * guarantees that when ZA is enabled it will be zeroed.
+ */
+void sme_alloc(struct task_struct *task)
+{
+	if (task->thread.za_state) {
+		memset(task->thread.za_state, 0, za_state_size(task));
+		return;
+	}
+
+	/* This could potentially be up to 64K. */
+	task->thread.za_state =
+		kzalloc(za_state_size(task), GFP_KERNEL);
+}
+
+static void sme_free(struct task_struct *task)
+{
+	kfree(task->thread.za_state);
+	task->thread.za_state = NULL;
+}
+
+void sme_kernel_enable(const struct arm64_cpu_capabilities *__always_unused p)
+{
+	/* Set priority for all PEs to architecturally defined minimum */
+	write_sysreg_s(read_sysreg_s(SYS_SMPRI_EL1) & ~SMPRI_EL1_PRIORITY_MASK,
+		       SYS_SMPRI_EL1);
+
+	/* Allow SME in kernel */
+	write_sysreg(read_sysreg(CPACR_EL1) | CPACR_EL1_SMEN_EL1EN, CPACR_EL1);
+	isb();
+
+	/* Allow EL0 to access TPIDR2 */
+	write_sysreg(read_sysreg(SCTLR_EL1) | SCTLR_ELx_ENTP2, SCTLR_EL1);
+	isb();
+}
+
+/*
+ * This must be called after sme_kernel_enable(), we rely on the
+ * feature table being sorted to ensure this.
+ */
+void fa64_kernel_enable(const struct arm64_cpu_capabilities *__always_unused p)
+{
+	/* Allow use of FA64 */
+	write_sysreg_s(read_sysreg_s(SYS_SMCR_EL1) | SMCR_ELx_FA64_MASK,
+		       SYS_SMCR_EL1);
+}
+
+/*
+ * Read the pseudo-SMCR used by cpufeatures to identify the supported
+ * vector length.
+ *
+ * Use only if SME is present.
+ * This function clobbers the SME vector length.
+ */
+u64 read_smcr_features(void)
+{
+	u64 smcr;
+	unsigned int vq_max;
+
+	sme_kernel_enable(NULL);
+	sme_smstart_sm();
+
+	/*
+	 * Set the maximum possible VL.
+	 */
+	write_sysreg_s(read_sysreg_s(SYS_SMCR_EL1) | SMCR_ELx_LEN_MASK,
+		       SYS_SMCR_EL1);
+
+	smcr = read_sysreg_s(SYS_SMCR_EL1);
+	smcr &= ~(u64)SMCR_ELx_LEN_MASK; /* Only the LEN field */
+	vq_max = sve_vq_from_vl(sve_get_vl());
+	smcr |= vq_max - 1; /* set LEN field to maximum effective value */
+
+	sme_smstop_sm();
+
+	return smcr;
+}
+
+void __init sme_setup(void)
+{
+	struct vl_info *info = &vl_info[ARM64_VEC_SME];
+	u64 smcr;
+	int min_bit;
+
+	if (!system_supports_sme())
+		return;
+
+	/*
+	 * SME doesn't require any particular vector length be
+	 * supported but it does require at least one.  We should have
+	 * disabled the feature entirely while bringing up CPUs but
+	 * let's double check here.
+	 */
+	WARN_ON(bitmap_empty(info->vq_map, SVE_VQ_MAX));
+
+	min_bit = find_last_bit(info->vq_map, SVE_VQ_MAX);
+	info->min_vl = sve_vl_from_vq(__bit_to_vq(min_bit));
+
+	smcr = read_sanitised_ftr_reg(SYS_SMCR_EL1);
+	info->max_vl = sve_vl_from_vq((smcr & SMCR_ELx_LEN_MASK) + 1);
+
+	/*
+	 * Sanity-check that the max VL we determined through CPU features
+	 * corresponds properly to sme_vq_map.  If not, do our best:
+	 */
+	if (WARN_ON(info->max_vl != find_supported_vector_length(ARM64_VEC_SME,
+								 info->max_vl)))
+		info->max_vl = find_supported_vector_length(ARM64_VEC_SME,
+							    info->max_vl);
+
+	WARN_ON(info->min_vl > info->max_vl);
+
+	/*
+	 * For the default VL, pick the maximum supported value <= 32
+	 * (256 bits) if there is one since this is guaranteed not to
+	 * grow the signal frame when in streaming mode, otherwise the
+	 * minimum available VL will be used.
+	 */
+	set_sme_default_vl(find_supported_vector_length(ARM64_VEC_SME, 32));
+
+	pr_info("SME: minimum available vector length %u bytes per vector\n",
+		info->min_vl);
+	pr_info("SME: maximum available vector length %u bytes per vector\n",
+		info->max_vl);
+	pr_info("SME: default vector length %u bytes per vector\n",
+		get_sme_default_vl());
+}
+
+#endif /* CONFIG_ARM64_SME */
+
+static void sve_init_regs(void)
+{
+	/*
+	 * Convert the FPSIMD state to SVE, zeroing all the state that
+	 * is not shared with FPSIMD. If (as is likely) the current
+	 * state is live in the registers then do this there and
+	 * update our metadata for the current task including
+	 * disabling the trap, otherwise update our in-memory copy.
+	 * We are guaranteed to not be in streaming mode, we can only
+	 * take a SVE trap when not in streaming mode and we can't be
+	 * in streaming mode when taking a SME trap.
+	 */
+	if (!test_thread_flag(TIF_FOREIGN_FPSTATE)) {
+		unsigned long vq_minus_one =
+			sve_vq_from_vl(task_get_sve_vl(current)) - 1;
+		sve_set_vq(vq_minus_one);
+		sve_flush_live(true, vq_minus_one);
+		fpsimd_bind_task_to_cpu();
+	} else {
+		fpsimd_to_sve(current);
+	}
+}
+
 /*
  * Trapped SVE access
  *
@@ -988,7 +1382,7 @@ void fpsimd_release_task(struct task_struct *dead_task)
  * would have disabled the SVE access trap for userspace during
  * ret_to_user, making an SVE access trap impossible in that case.
  */
-void do_sve_acc(unsigned int esr, struct pt_regs *regs)
+void do_sve_acc(unsigned long esr, struct pt_regs *regs)
 {
 	/* Even if we chose not to use SVE, the hardware could still trap: */
 	if (unlikely(!system_supports_sve()) || WARN_ON(is_compat_task())) {
@@ -996,7 +1390,7 @@ void do_sve_acc(unsigned int esr, struct pt_regs *regs)
 		return;
 	}
 
-	sve_alloc(current);
+	sve_alloc(current, true);
 	if (!current->thread.sve_state) {
 		force_sig(SIGKILL);
 		return;
@@ -1008,20 +1402,64 @@ void do_sve_acc(unsigned int esr, struct pt_regs *regs)
 		WARN_ON(1); /* SVE access shouldn't have trapped */
 
 	/*
-	 * Convert the FPSIMD state to SVE, zeroing all the state that
-	 * is not shared with FPSIMD. If (as is likely) the current
-	 * state is live in the registers then do this there and
-	 * update our metadata for the current task including
-	 * disabling the trap, otherwise update our in-memory copy.
+	 * Even if the task can have used streaming mode we can only
+	 * generate SVE access traps in normal SVE mode and
+	 * transitioning out of streaming mode may discard any
+	 * streaming mode state.  Always clear the high bits to avoid
+	 * any potential errors tracking what is properly initialised.
+	 */
+	sve_init_regs();
+
+	put_cpu_fpsimd_context();
+}
+
+/*
+ * Trapped SME access
+ *
+ * Storage is allocated for the full SVE and SME state, the current
+ * FPSIMD register contents are migrated to SVE if SVE is not already
+ * active, and the access trap is disabled.
+ *
+ * TIF_SME should be clear on entry: otherwise, fpsimd_restore_current_state()
+ * would have disabled the SME access trap for userspace during
+ * ret_to_user, making an SVE access trap impossible in that case.
+ */
+void do_sme_acc(unsigned long esr, struct pt_regs *regs)
+{
+	/* Even if we chose not to use SME, the hardware could still trap: */
+	if (unlikely(!system_supports_sme()) || WARN_ON(is_compat_task())) {
+		force_signal_inject(SIGILL, ILL_ILLOPC, regs->pc, 0);
+		return;
+	}
+
+	/*
+	 * If this not a trap due to SME being disabled then something
+	 * is being used in the wrong mode, report as SIGILL.
 	 */
+	if (ESR_ELx_ISS(esr) != ESR_ELx_SME_ISS_SME_DISABLED) {
+		force_signal_inject(SIGILL, ILL_ILLOPC, regs->pc, 0);
+		return;
+	}
+
+	sve_alloc(current, false);
+	sme_alloc(current);
+	if (!current->thread.sve_state || !current->thread.za_state) {
+		force_sig(SIGKILL);
+		return;
+	}
+
+	get_cpu_fpsimd_context();
+
+	/* With TIF_SME userspace shouldn't generate any traps */
+	if (test_and_set_thread_flag(TIF_SME))
+		WARN_ON(1);
+
 	if (!test_thread_flag(TIF_FOREIGN_FPSTATE)) {
 		unsigned long vq_minus_one =
-			sve_vq_from_vl(task_get_sve_vl(current)) - 1;
-		sve_set_vq(vq_minus_one);
-		sve_flush_live(true, vq_minus_one);
+			sve_vq_from_vl(task_get_sme_vl(current)) - 1;
+		sme_set_vq(vq_minus_one);
+
 		fpsimd_bind_task_to_cpu();
-	} else {
-		fpsimd_to_sve(current);
 	}
 
 	put_cpu_fpsimd_context();
@@ -1030,7 +1468,7 @@ void do_sve_acc(unsigned int esr, struct pt_regs *regs)
 /*
  * Trapped FP/ASIMD access.
  */
-void do_fpsimd_acc(unsigned int esr, struct pt_regs *regs)
+void do_fpsimd_acc(unsigned long esr, struct pt_regs *regs)
 {
 	/* TODO: implement lazy context saving/restoring */
 	WARN_ON(1);
@@ -1039,7 +1477,7 @@ void do_fpsimd_acc(unsigned int esr, struct pt_regs *regs)
 /*
  * Raise a SIGFPE for the current process.
  */
-void do_fpsimd_exc(unsigned int esr, struct pt_regs *regs)
+void do_fpsimd_exc(unsigned long esr, struct pt_regs *regs)
 {
 	unsigned int si_code = FPE_FLTUNK;
 
@@ -1107,7 +1545,7 @@ static void fpsimd_flush_thread_vl(enum vec_type type)
 		vl = get_default_vl(type);
 
 	if (WARN_ON(!sve_vl_valid(vl)))
-		vl = SVE_VL_MIN;
+		vl = vl_info[type].min_vl;
 
 	supported_vl = find_supported_vector_length(type, vl);
 	if (WARN_ON(supported_vl != vl))
@@ -1125,6 +1563,9 @@ static void fpsimd_flush_thread_vl(enum vec_type type)
 
 void fpsimd_flush_thread(void)
 {
+	void *sve_state = NULL;
+	void *za_state = NULL;
+
 	if (!system_supports_fpsimd())
 		return;
 
@@ -1136,11 +1577,28 @@ void fpsimd_flush_thread(void)
 
 	if (system_supports_sve()) {
 		clear_thread_flag(TIF_SVE);
-		sve_free(current);
+
+		/* Defer kfree() while in atomic context */
+		sve_state = current->thread.sve_state;
+		current->thread.sve_state = NULL;
+
 		fpsimd_flush_thread_vl(ARM64_VEC_SVE);
 	}
 
+	if (system_supports_sme()) {
+		clear_thread_flag(TIF_SME);
+
+		/* Defer kfree() while in atomic context */
+		za_state = current->thread.za_state;
+		current->thread.za_state = NULL;
+
+		fpsimd_flush_thread_vl(ARM64_VEC_SME);
+		current->thread.svcr = 0;
+	}
+
 	put_cpu_fpsimd_context();
+	kfree(sve_state);
+	kfree(za_state);
 }
 
 /*
@@ -1182,22 +1640,34 @@ static void fpsimd_bind_task_to_cpu(void)
 	WARN_ON(!system_supports_fpsimd());
 	last->st = &current->thread.uw.fpsimd_state;
 	last->sve_state = current->thread.sve_state;
+	last->za_state = current->thread.za_state;
 	last->sve_vl = task_get_sve_vl(current);
+	last->sme_vl = task_get_sme_vl(current);
+	last->svcr = &current->thread.svcr;
 	current->thread.fpsimd_cpu = smp_processor_id();
 
+	/*
+	 * Toggle SVE and SME trapping for userspace if needed, these
+	 * are serialsied by ret_to_user().
+	 */
+	if (system_supports_sme()) {
+		if (test_thread_flag(TIF_SME))
+			sme_user_enable();
+		else
+			sme_user_disable();
+	}
+
 	if (system_supports_sve()) {
-		/* Toggle SVE trapping for userspace if needed */
 		if (test_thread_flag(TIF_SVE))
 			sve_user_enable();
 		else
 			sve_user_disable();
-
-		/* Serialised by exception return to user */
 	}
 }
 
 void fpsimd_bind_state_to_cpu(struct user_fpsimd_state *st, void *sve_state,
-			      unsigned int sve_vl)
+			      unsigned int sve_vl, void *za_state,
+			      unsigned int sme_vl, u64 *svcr)
 {
 	struct fpsimd_last_state_struct *last =
 		this_cpu_ptr(&fpsimd_last_state);
@@ -1206,14 +1676,18 @@ void fpsimd_bind_state_to_cpu(struct user_fpsimd_state *st, void *sve_state,
 	WARN_ON(!in_softirq() && !irqs_disabled());
 
 	last->st = st;
+	last->svcr = svcr;
 	last->sve_state = sve_state;
+	last->za_state = za_state;
 	last->sve_vl = sve_vl;
+	last->sme_vl = sme_vl;
 }
 
 /*
  * Load the userland FPSIMD state of 'current' from memory, but only if the
  * FPSIMD state already held in the registers is /not/ the most recent FPSIMD
- * state of 'current'
+ * state of 'current'.  This is called when we are preparing to return to
+ * userspace to ensure that userspace sees a good register state.
  */
 void fpsimd_restore_current_state(void)
 {
@@ -1244,7 +1718,9 @@ void fpsimd_restore_current_state(void)
 /*
  * Load an updated userland FPSIMD state for 'current' from memory and set the
  * flag that indicates that the FPSIMD register contents are the most recent
- * FPSIMD state of 'current'
+ * FPSIMD state of 'current'. This is used by the signal code to restore the
+ * register state when returning from a signal handler in FPSIMD only cases,
+ * any SVE context will be discarded.
  */
 void fpsimd_update_current_state(struct user_fpsimd_state const *state)
 {
@@ -1301,6 +1777,15 @@ static void fpsimd_flush_cpu_state(void)
 {
 	WARN_ON(!system_supports_fpsimd());
 	__this_cpu_write(fpsimd_last_state.st, NULL);
+
+	/*
+	 * Leaving streaming mode enabled will cause issues for any kernel
+	 * NEON and leaving streaming mode or ZA enabled may increase power
+	 * consumption.
+	 */
+	if (system_supports_sme())
+		sme_smstop();
+
 	set_thread_flag(TIF_FOREIGN_FPSTATE);
 }
 
@@ -1378,6 +1863,7 @@ EXPORT_SYMBOL(kernel_neon_end);
 static DEFINE_PER_CPU(struct user_fpsimd_state, efi_fpsimd_state);
 static DEFINE_PER_CPU(bool, efi_fpsimd_state_used);
 static DEFINE_PER_CPU(bool, efi_sve_state_used);
+static DEFINE_PER_CPU(bool, efi_sm_state);
 
 /*
  * EFI runtime services support functions
@@ -1412,12 +1898,33 @@ void __efi_fpsimd_begin(void)
 		 */
 		if (system_supports_sve() && likely(efi_sve_state)) {
 			char *sve_state = this_cpu_ptr(efi_sve_state);
+			bool ffr = true;
+			u64 svcr;
 
 			__this_cpu_write(efi_sve_state_used, true);
 
+			if (system_supports_sme()) {
+				svcr = read_sysreg_s(SYS_SVCR);
+
+				__this_cpu_write(efi_sm_state,
+						 svcr & SVCR_SM_MASK);
+
+				/*
+				 * Unless we have FA64 FFR does not
+				 * exist in streaming mode.
+				 */
+				if (!system_supports_fa64())
+					ffr = !(svcr & SVCR_SM_MASK);
+			}
+
 			sve_save_state(sve_state + sve_ffr_offset(sve_max_vl()),
 				       &this_cpu_ptr(&efi_fpsimd_state)->fpsr,
-				       true);
+				       ffr);
+
+			if (system_supports_sme())
+				sysreg_clear_set_s(SYS_SVCR,
+						   SVCR_SM_MASK, 0);
+
 		} else {
 			fpsimd_save_state(this_cpu_ptr(&efi_fpsimd_state));
 		}
@@ -1440,11 +1947,31 @@ void __efi_fpsimd_end(void)
 		if (system_supports_sve() &&
 		    likely(__this_cpu_read(efi_sve_state_used))) {
 			char const *sve_state = this_cpu_ptr(efi_sve_state);
+			bool ffr = true;
+
+			/*
+			 * Restore streaming mode; EFI calls are
+			 * normal function calls so should not return in
+			 * streaming mode.
+			 */
+			if (system_supports_sme()) {
+				if (__this_cpu_read(efi_sm_state)) {
+					sysreg_clear_set_s(SYS_SVCR,
+							   0,
+							   SVCR_SM_MASK);
+
+					/*
+					 * Unless we have FA64 FFR does not
+					 * exist in streaming mode.
+					 */
+					if (!system_supports_fa64())
+						ffr = false;
+				}
+			}
 
-			sve_set_vq(sve_vq_from_vl(sve_get_vl()) - 1);
 			sve_load_state(sve_state + sve_ffr_offset(sve_max_vl()),
 				       &this_cpu_ptr(&efi_fpsimd_state)->fpsr,
-				       true);
+				       ffr);
 
 			__this_cpu_write(efi_sve_state_used, false);
 		} else {
@@ -1519,6 +2046,13 @@ static int __init fpsimd_init(void)
 	if (!cpu_have_named_feature(ASIMD))
 		pr_notice("Advanced SIMD is not implemented\n");
 
-	return sve_sysctl_init();
+
+	if (cpu_have_named_feature(SME) && !cpu_have_named_feature(SVE))
+		pr_notice("SME is implemented but not SVE\n");
+
+	sve_sysctl_init();
+	sme_sysctl_init();
+
+	return 0;
 }
 core_initcall(fpsimd_init);
diff --git a/arch/arm64/kernel/ftrace.c b/arch/arm64/kernel/ftrace.c
index 4506c4a90ac1..8745175f4a75 100644
--- a/arch/arm64/kernel/ftrace.c
+++ b/arch/arm64/kernel/ftrace.c
@@ -56,7 +56,7 @@ int ftrace_update_ftrace_func(ftrace_func_t func)
 	unsigned long pc;
 	u32 new;
 
-	pc = (unsigned long)function_nocfi(ftrace_call);
+	pc = (unsigned long)ftrace_call;
 	new = aarch64_insn_gen_branch_imm(pc, (unsigned long)func,
 					  AARCH64_INSN_BRANCH_LINK);
 
@@ -78,47 +78,76 @@ static struct plt_entry *get_ftrace_plt(struct module *mod, unsigned long addr)
 }
 
 /*
- * Turn on the call to ftrace_caller() in instrumented function
+ * Find the address the callsite must branch to in order to reach '*addr'.
+ *
+ * Due to the limited range of 'BL' instructions, modules may be placed too far
+ * away to branch directly and must use a PLT.
+ *
+ * Returns true when '*addr' contains a reachable target address, or has been
+ * modified to contain a PLT address. Returns false otherwise.
  */
-int ftrace_make_call(struct dyn_ftrace *rec, unsigned long addr)
+static bool ftrace_find_callable_addr(struct dyn_ftrace *rec,
+				      struct module *mod,
+				      unsigned long *addr)
 {
 	unsigned long pc = rec->ip;
-	u32 old, new;
-	long offset = (long)pc - (long)addr;
+	long offset = (long)*addr - (long)pc;
+	struct plt_entry *plt;
 
-	if (offset < -SZ_128M || offset >= SZ_128M) {
-		struct module *mod;
-		struct plt_entry *plt;
+	/*
+	 * When the target is within range of the 'BL' instruction, use 'addr'
+	 * as-is and branch to that directly.
+	 */
+	if (offset >= -SZ_128M && offset < SZ_128M)
+		return true;
 
-		if (!IS_ENABLED(CONFIG_ARM64_MODULE_PLTS))
-			return -EINVAL;
+	/*
+	 * When the target is outside of the range of a 'BL' instruction, we
+	 * must use a PLT to reach it. We can only place PLTs for modules, and
+	 * only when module PLT support is built-in.
+	 */
+	if (!IS_ENABLED(CONFIG_ARM64_MODULE_PLTS))
+		return false;
 
-		/*
-		 * On kernels that support module PLTs, the offset between the
-		 * branch instruction and its target may legally exceed the
-		 * range of an ordinary relative 'bl' opcode. In this case, we
-		 * need to branch via a trampoline in the module.
-		 *
-		 * NOTE: __module_text_address() must be called with preemption
-		 * disabled, but we can rely on ftrace_lock to ensure that 'mod'
-		 * retains its validity throughout the remainder of this code.
-		 */
+	/*
+	 * 'mod' is only set at module load time, but if we end up
+	 * dealing with an out-of-range condition, we can assume it
+	 * is due to a module being loaded far away from the kernel.
+	 *
+	 * NOTE: __module_text_address() must be called with preemption
+	 * disabled, but we can rely on ftrace_lock to ensure that 'mod'
+	 * retains its validity throughout the remainder of this code.
+	 */
+	if (!mod) {
 		preempt_disable();
 		mod = __module_text_address(pc);
 		preempt_enable();
+	}
 
-		if (WARN_ON(!mod))
-			return -EINVAL;
-
-		plt = get_ftrace_plt(mod, addr);
-		if (!plt) {
-			pr_err("ftrace: no module PLT for %ps\n", (void *)addr);
-			return -EINVAL;
-		}
+	if (WARN_ON(!mod))
+		return false;
 
-		addr = (unsigned long)plt;
+	plt = get_ftrace_plt(mod, *addr);
+	if (!plt) {
+		pr_err("ftrace: no module PLT for %ps\n", (void *)*addr);
+		return false;
 	}
 
+	*addr = (unsigned long)plt;
+	return true;
+}
+
+/*
+ * Turn on the call to ftrace_caller() in instrumented function
+ */
+int ftrace_make_call(struct dyn_ftrace *rec, unsigned long addr)
+{
+	unsigned long pc = rec->ip;
+	u32 old, new;
+
+	if (!ftrace_find_callable_addr(rec, NULL, &addr))
+		return -EINVAL;
+
 	old = aarch64_insn_gen_nop();
 	new = aarch64_insn_gen_branch_imm(pc, addr, AARCH64_INSN_BRANCH_LINK);
 
@@ -132,6 +161,11 @@ int ftrace_modify_call(struct dyn_ftrace *rec, unsigned long old_addr,
 	unsigned long pc = rec->ip;
 	u32 old, new;
 
+	if (!ftrace_find_callable_addr(rec, NULL, &old_addr))
+		return -EINVAL;
+	if (!ftrace_find_callable_addr(rec, NULL, &addr))
+		return -EINVAL;
+
 	old = aarch64_insn_gen_branch_imm(pc, old_addr,
 					  AARCH64_INSN_BRANCH_LINK);
 	new = aarch64_insn_gen_branch_imm(pc, addr, AARCH64_INSN_BRANCH_LINK);
@@ -181,54 +215,30 @@ int ftrace_make_nop(struct module *mod, struct dyn_ftrace *rec,
 		    unsigned long addr)
 {
 	unsigned long pc = rec->ip;
-	bool validate = true;
 	u32 old = 0, new;
-	long offset = (long)pc - (long)addr;
-
-	if (offset < -SZ_128M || offset >= SZ_128M) {
-		u32 replaced;
-
-		if (!IS_ENABLED(CONFIG_ARM64_MODULE_PLTS))
-			return -EINVAL;
-
-		/*
-		 * 'mod' is only set at module load time, but if we end up
-		 * dealing with an out-of-range condition, we can assume it
-		 * is due to a module being loaded far away from the kernel.
-		 */
-		if (!mod) {
-			preempt_disable();
-			mod = __module_text_address(pc);
-			preempt_enable();
-
-			if (WARN_ON(!mod))
-				return -EINVAL;
-		}
-
-		/*
-		 * The instruction we are about to patch may be a branch and
-		 * link instruction that was redirected via a PLT entry. In
-		 * this case, the normal validation will fail, but we can at
-		 * least check that we are dealing with a branch and link
-		 * instruction that points into the right module.
-		 */
-		if (aarch64_insn_read((void *)pc, &replaced))
-			return -EFAULT;
 
-		if (!aarch64_insn_is_bl(replaced) ||
-		    !within_module(pc + aarch64_get_branch_offset(replaced),
-				   mod))
-			return -EINVAL;
+	new = aarch64_insn_gen_nop();
 
-		validate = false;
-	} else {
-		old = aarch64_insn_gen_branch_imm(pc, addr,
-						  AARCH64_INSN_BRANCH_LINK);
+	/*
+	 * When using mcount, callsites in modules may have been initalized to
+	 * call an arbitrary module PLT (which redirects to the _mcount stub)
+	 * rather than the ftrace PLT we'll use at runtime (which redirects to
+	 * the ftrace trampoline). We can ignore the old PLT when initializing
+	 * the callsite.
+	 *
+	 * Note: 'mod' is only set at module load time.
+	 */
+	if (!IS_ENABLED(CONFIG_DYNAMIC_FTRACE_WITH_REGS) &&
+	    IS_ENABLED(CONFIG_ARM64_MODULE_PLTS) && mod) {
+		return aarch64_insn_patch_text_nosync((void *)pc, new);
 	}
 
-	new = aarch64_insn_gen_nop();
+	if (!ftrace_find_callable_addr(rec, mod, &addr))
+		return -EINVAL;
 
-	return ftrace_modify_code(pc, old, new, validate);
+	old = aarch64_insn_gen_branch_imm(pc, addr, AARCH64_INSN_BRANCH_LINK);
+
+	return ftrace_modify_code(pc, old, new, true);
 }
 
 void arch_ftrace_update_code(int command)
@@ -268,6 +278,22 @@ void prepare_ftrace_return(unsigned long self_addr, unsigned long *parent,
 }
 
 #ifdef CONFIG_DYNAMIC_FTRACE
+
+#ifdef CONFIG_DYNAMIC_FTRACE_WITH_REGS
+void ftrace_graph_func(unsigned long ip, unsigned long parent_ip,
+		       struct ftrace_ops *op, struct ftrace_regs *fregs)
+{
+	/*
+	 * When DYNAMIC_FTRACE_WITH_REGS is selected, `fregs` can never be NULL
+	 * and arch_ftrace_get_regs(fregs) will always give a non-NULL pt_regs
+	 * in which we can safely modify the LR.
+	 */
+	struct pt_regs *regs = arch_ftrace_get_regs(fregs);
+	unsigned long *parent = (unsigned long *)&procedure_link_pointer(regs);
+
+	prepare_ftrace_return(ip, parent, frame_pointer(regs));
+}
+#else
 /*
  * Turn on/off the call to ftrace_graph_caller() in ftrace_caller()
  * depending on @enable.
@@ -297,5 +323,6 @@ int ftrace_disable_ftrace_graph_caller(void)
 {
 	return ftrace_modify_graph_caller(false);
 }
+#endif /* CONFIG_DYNAMIC_FTRACE_WITH_REGS */
 #endif /* CONFIG_DYNAMIC_FTRACE */
 #endif /* CONFIG_FUNCTION_GRAPH_TRACER */
diff --git a/arch/arm64/kernel/head.S b/arch/arm64/kernel/head.S
index 6a98f1a38c29..2196aad7b55b 100644
--- a/arch/arm64/kernel/head.S
+++ b/arch/arm64/kernel/head.S
@@ -37,8 +37,6 @@
 
 #include "efi-header.S"
 
-#define __PHYS_OFFSET	KERNEL_START
-
 #if (PAGE_OFFSET & 0x1fffff) != 0
 #error PAGE_OFFSET must be at least 2MB aligned
 #endif
@@ -51,9 +49,6 @@
  *   MMU = off, D-cache = off, I-cache = on or off,
  *   x0 = physical address to the FDT blob.
  *
- * This code is mostly position independent so you call this at
- * __pa(PAGE_OFFSET).
- *
  * Note that the callee-saved registers are used for storing variables
  * that are useful before the MMU is enabled. The allocations are described
  * in the entry routines.
@@ -82,25 +77,34 @@
 	 * primary lowlevel boot path:
 	 *
 	 *  Register   Scope                      Purpose
+	 *  x20        primary_entry() .. __primary_switch()    CPU boot mode
 	 *  x21        primary_entry() .. start_kernel()        FDT pointer passed at boot in x0
+	 *  x22        create_idmap() .. start_kernel()         ID map VA of the DT blob
 	 *  x23        primary_entry() .. start_kernel()        physical misalignment/KASLR offset
-	 *  x28        __create_page_tables()                   callee preserved temp register
-	 *  x19/x20    __primary_switch()                       callee preserved temp registers
-	 *  x24        __primary_switch() .. relocate_kernel()  current RELR displacement
+	 *  x24        __primary_switch()                       linear map KASLR seed
+	 *  x25        primary_entry() .. start_kernel()        supported VA size
+	 *  x28        create_idmap()                           callee preserved temp register
 	 */
 SYM_CODE_START(primary_entry)
 	bl	preserve_boot_args
 	bl	init_kernel_el			// w0=cpu_boot_mode
-	adrp	x23, __PHYS_OFFSET
-	and	x23, x23, MIN_KIMG_ALIGN - 1	// KASLR offset, defaults to 0
-	bl	set_cpu_boot_mode_flag
-	bl	__create_page_tables
+	mov	x20, x0
+	bl	create_idmap
+
 	/*
 	 * The following calls CPU setup code, see arch/arm64/mm/proc.S for
 	 * details.
 	 * On return, the CPU will be ready for the MMU to be turned on and
 	 * the TCR will have been set.
 	 */
+#if VA_BITS > 48
+	mrs_s	x0, SYS_ID_AA64MMFR2_EL1
+	tst	x0, #0xf << ID_AA64MMFR2_EL1_VARange_SHIFT
+	mov	x0, #VA_BITS
+	mov	x25, #VA_BITS_MIN
+	csel	x25, x25, x0, eq
+	mov	x0, x25
+#endif
 	bl	__cpu_setup			// initialise processor
 	b	__primary_switch
 SYM_CODE_END(primary_entry)
@@ -122,28 +126,16 @@ SYM_CODE_START_LOCAL(preserve_boot_args)
 	b	dcache_inval_poc		// tail call
 SYM_CODE_END(preserve_boot_args)
 
-/*
- * Macro to create a table entry to the next page.
- *
- *	tbl:	page table address
- *	virt:	virtual address
- *	shift:	#imm page table shift
- *	ptrs:	#imm pointers per table page
- *
- * Preserves:	virt
- * Corrupts:	ptrs, tmp1, tmp2
- * Returns:	tbl -> next level table page address
- */
-	.macro	create_table_entry, tbl, virt, shift, ptrs, tmp1, tmp2
-	add	\tmp1, \tbl, #PAGE_SIZE
-	phys_to_pte \tmp2, \tmp1
-	orr	\tmp2, \tmp2, #PMD_TYPE_TABLE	// address of next table and entry type
-	lsr	\tmp1, \virt, #\shift
-	sub	\ptrs, \ptrs, #1
-	and	\tmp1, \tmp1, \ptrs		// table index
-	str	\tmp2, [\tbl, \tmp1, lsl #3]
-	add	\tbl, \tbl, #PAGE_SIZE		// next level table page
-	.endm
+SYM_FUNC_START_LOCAL(clear_page_tables)
+	/*
+	 * Clear the init page tables.
+	 */
+	adrp	x0, init_pg_dir
+	adrp	x1, init_pg_end
+	sub	x2, x1, x0
+	mov	x1, xzr
+	b	__pi_memset			// tail call
+SYM_FUNC_END(clear_page_tables)
 
 /*
  * Macro to populate page table entries, these entries can be pointers to the next level
@@ -179,31 +171,20 @@ SYM_CODE_END(preserve_boot_args)
  *	vstart:	virtual address of start of range
  *	vend:	virtual address of end of range - we map [vstart, vend]
  *	shift:	shift used to transform virtual address into index
- *	ptrs:	number of entries in page table
+ *	order:  #imm 2log(number of entries in page table)
  *	istart:	index in table corresponding to vstart
  *	iend:	index in table corresponding to vend
  *	count:	On entry: how many extra entries were required in previous level, scales
  *			  our end index.
  *		On exit: returns how many extra entries required for next page table level
  *
- * Preserves:	vstart, vend, shift, ptrs
+ * Preserves:	vstart, vend
  * Returns:	istart, iend, count
  */
-	.macro compute_indices, vstart, vend, shift, ptrs, istart, iend, count
-	lsr	\iend, \vend, \shift
-	mov	\istart, \ptrs
-	sub	\istart, \istart, #1
-	and	\iend, \iend, \istart	// iend = (vend >> shift) & (ptrs - 1)
-	mov	\istart, \ptrs
-	mul	\istart, \istart, \count
-	add	\iend, \iend, \istart	// iend += count * ptrs
-					// our entries span multiple tables
-
-	lsr	\istart, \vstart, \shift
-	mov	\count, \ptrs
-	sub	\count, \count, #1
-	and	\istart, \istart, \count
-
+	.macro compute_indices, vstart, vend, shift, order, istart, iend, count
+	ubfx	\istart, \vstart, \shift, \order
+	ubfx	\iend, \vend, \shift, \order
+	add	\iend, \iend, \count, lsl \order
 	sub	\count, \iend, \istart
 	.endm
 
@@ -218,119 +199,116 @@ SYM_CODE_END(preserve_boot_args)
  *	vend:	virtual address of end of range - we map [vstart, vend - 1]
  *	flags:	flags to use to map last level entries
  *	phys:	physical address corresponding to vstart - physical memory is contiguous
- *	pgds:	the number of pgd entries
+ *	order:  #imm 2log(number of entries in PGD table)
+ *
+ * If extra_shift is set, an extra level will be populated if the end address does
+ * not fit in 'extra_shift' bits. This assumes vend is in the TTBR0 range.
  *
  * Temporaries:	istart, iend, tmp, count, sv - these need to be different registers
  * Preserves:	vstart, flags
  * Corrupts:	tbl, rtbl, vend, istart, iend, tmp, count, sv
  */
-	.macro map_memory, tbl, rtbl, vstart, vend, flags, phys, pgds, istart, iend, tmp, count, sv
+	.macro map_memory, tbl, rtbl, vstart, vend, flags, phys, order, istart, iend, tmp, count, sv, extra_shift
 	sub \vend, \vend, #1
 	add \rtbl, \tbl, #PAGE_SIZE
-	mov \sv, \rtbl
 	mov \count, #0
-	compute_indices \vstart, \vend, #PGDIR_SHIFT, \pgds, \istart, \iend, \count
+
+	.ifnb	\extra_shift
+	tst	\vend, #~((1 << (\extra_shift)) - 1)
+	b.eq	.L_\@
+	compute_indices \vstart, \vend, #\extra_shift, #(PAGE_SHIFT - 3), \istart, \iend, \count
+	mov \sv, \rtbl
 	populate_entries \tbl, \rtbl, \istart, \iend, #PMD_TYPE_TABLE, #PAGE_SIZE, \tmp
 	mov \tbl, \sv
+	.endif
+.L_\@:
+	compute_indices \vstart, \vend, #PGDIR_SHIFT, #\order, \istart, \iend, \count
 	mov \sv, \rtbl
+	populate_entries \tbl, \rtbl, \istart, \iend, #PMD_TYPE_TABLE, #PAGE_SIZE, \tmp
+	mov \tbl, \sv
 
 #if SWAPPER_PGTABLE_LEVELS > 3
-	compute_indices \vstart, \vend, #PUD_SHIFT, #PTRS_PER_PUD, \istart, \iend, \count
+	compute_indices \vstart, \vend, #PUD_SHIFT, #(PAGE_SHIFT - 3), \istart, \iend, \count
+	mov \sv, \rtbl
 	populate_entries \tbl, \rtbl, \istart, \iend, #PMD_TYPE_TABLE, #PAGE_SIZE, \tmp
 	mov \tbl, \sv
-	mov \sv, \rtbl
 #endif
 
 #if SWAPPER_PGTABLE_LEVELS > 2
-	compute_indices \vstart, \vend, #SWAPPER_TABLE_SHIFT, #PTRS_PER_PMD, \istart, \iend, \count
+	compute_indices \vstart, \vend, #SWAPPER_TABLE_SHIFT, #(PAGE_SHIFT - 3), \istart, \iend, \count
+	mov \sv, \rtbl
 	populate_entries \tbl, \rtbl, \istart, \iend, #PMD_TYPE_TABLE, #PAGE_SIZE, \tmp
 	mov \tbl, \sv
 #endif
 
-	compute_indices \vstart, \vend, #SWAPPER_BLOCK_SHIFT, #PTRS_PER_PTE, \istart, \iend, \count
-	bic \count, \phys, #SWAPPER_BLOCK_SIZE - 1
-	populate_entries \tbl, \count, \istart, \iend, \flags, #SWAPPER_BLOCK_SIZE, \tmp
+	compute_indices \vstart, \vend, #SWAPPER_BLOCK_SHIFT, #(PAGE_SHIFT - 3), \istart, \iend, \count
+	bic \rtbl, \phys, #SWAPPER_BLOCK_SIZE - 1
+	populate_entries \tbl, \rtbl, \istart, \iend, \flags, #SWAPPER_BLOCK_SIZE, \tmp
 	.endm
 
 /*
- * Setup the initial page tables. We only setup the barest amount which is
- * required to get the kernel running. The following sections are required:
- *   - identity mapping to enable the MMU (low address, TTBR0)
- *   - first few MB of the kernel linear mapping to jump to once the MMU has
- *     been enabled
+ * Remap a subregion created with the map_memory macro with modified attributes
+ * or output address. The entire remapped region must have been covered in the
+ * invocation of map_memory.
+ *
+ * x0: last level table address (returned in first argument to map_memory)
+ * x1: start VA of the existing mapping
+ * x2: start VA of the region to update
+ * x3: end VA of the region to update (exclusive)
+ * x4: start PA associated with the region to update
+ * x5: attributes to set on the updated region
+ * x6: order of the last level mappings
  */
-SYM_FUNC_START_LOCAL(__create_page_tables)
-	mov	x28, lr
+SYM_FUNC_START_LOCAL(remap_region)
+	sub	x3, x3, #1		// make end inclusive
 
-	/*
-	 * Invalidate the init page tables to avoid potential dirty cache lines
-	 * being evicted. Other page tables are allocated in rodata as part of
-	 * the kernel image, and thus are clean to the PoC per the boot
-	 * protocol.
-	 */
-	adrp	x0, init_pg_dir
-	adrp	x1, init_pg_end
-	bl	dcache_inval_poc
+	// Get the index offset for the start of the last level table
+	lsr	x1, x1, x6
+	bfi	x1, xzr, #0, #PAGE_SHIFT - 3
 
-	/*
-	 * Clear the init page tables.
-	 */
-	adrp	x0, init_pg_dir
-	adrp	x1, init_pg_end
-	sub	x1, x1, x0
-1:	stp	xzr, xzr, [x0], #16
-	stp	xzr, xzr, [x0], #16
-	stp	xzr, xzr, [x0], #16
-	stp	xzr, xzr, [x0], #16
-	subs	x1, x1, #64
-	b.ne	1b
+	// Derive the start and end indexes into the last level table
+	// associated with the provided region
+	lsr	x2, x2, x6
+	lsr	x3, x3, x6
+	sub	x2, x2, x1
+	sub	x3, x3, x1
 
-	mov	x7, SWAPPER_MM_MMUFLAGS
+	mov	x1, #1
+	lsl	x6, x1, x6		// block size at this level
 
-	/*
-	 * Create the identity mapping.
-	 */
-	adrp	x0, idmap_pg_dir
-	adrp	x3, __idmap_text_start		// __pa(__idmap_text_start)
-
-#ifdef CONFIG_ARM64_VA_BITS_52
-	mrs_s	x6, SYS_ID_AA64MMFR2_EL1
-	and	x6, x6, #(0xf << ID_AA64MMFR2_LVA_SHIFT)
-	mov	x5, #52
-	cbnz	x6, 1f
-#endif
-	mov	x5, #VA_BITS_MIN
-1:
-	adr_l	x6, vabits_actual
-	str	x5, [x6]
-	dmb	sy
-	dc	ivac, x6		// Invalidate potentially stale cache line
+	populate_entries x0, x4, x2, x3, x5, x6, x7
+	ret
+SYM_FUNC_END(remap_region)
 
+SYM_FUNC_START_LOCAL(create_idmap)
+	mov	x28, lr
 	/*
-	 * VA_BITS may be too small to allow for an ID mapping to be created
-	 * that covers system RAM if that is located sufficiently high in the
-	 * physical address space. So for the ID map, use an extended virtual
-	 * range in that case, and configure an additional translation level
-	 * if needed.
+	 * The ID map carries a 1:1 mapping of the physical address range
+	 * covered by the loaded image, which could be anywhere in DRAM. This
+	 * means that the required size of the VA (== PA) space is decided at
+	 * boot time, and could be more than the configured size of the VA
+	 * space for ordinary kernel and user space mappings.
+	 *
+	 * There are three cases to consider here:
+	 * - 39 <= VA_BITS < 48, and the ID map needs up to 48 VA bits to cover
+	 *   the placement of the image. In this case, we configure one extra
+	 *   level of translation on the fly for the ID map only. (This case
+	 *   also covers 42-bit VA/52-bit PA on 64k pages).
 	 *
-	 * Calculate the maximum allowed value for TCR_EL1.T0SZ so that the
-	 * entire ID map region can be mapped. As T0SZ == (64 - #bits used),
-	 * this number conveniently equals the number of leading zeroes in
-	 * the physical address of __idmap_text_end.
+	 * - VA_BITS == 48, and the ID map needs more than 48 VA bits. This can
+	 *   only happen when using 64k pages, in which case we need to extend
+	 *   the root level table rather than add a level. Note that we can
+	 *   treat this case as 'always extended' as long as we take care not
+	 *   to program an unsupported T0SZ value into the TCR register.
+	 *
+	 * - Combinations that would require two additional levels of
+	 *   translation are not supported, e.g., VA_BITS==36 on 16k pages, or
+	 *   VA_BITS==39/4k pages with 5-level paging, where the input address
+	 *   requires more than 47 or 48 bits, respectively.
 	 */
-	adrp	x5, __idmap_text_end
-	clz	x5, x5
-	cmp	x5, TCR_T0SZ(VA_BITS_MIN) // default T0SZ small enough?
-	b.ge	1f			// .. then skip VA range extension
-
-	adr_l	x6, idmap_t0sz
-	str	x5, [x6]
-	dmb	sy
-	dc	ivac, x6		// Invalidate potentially stale cache line
-
 #if (VA_BITS < 48)
+#define IDMAP_PGD_ORDER	(VA_BITS - PGDIR_SHIFT)
 #define EXTRA_SHIFT	(PGDIR_SHIFT + PAGE_SHIFT - 3)
-#define EXTRA_PTRS	(1 << (PHYS_MASK_SHIFT - EXTRA_SHIFT))
 
 	/*
 	 * If VA_BITS < 48, we have to configure an additional table level.
@@ -342,36 +320,40 @@ SYM_FUNC_START_LOCAL(__create_page_tables)
 #if VA_BITS != EXTRA_SHIFT
 #error "Mismatch between VA_BITS and page size/number of translation levels"
 #endif
-
-	mov	x4, EXTRA_PTRS
-	create_table_entry x0, x3, EXTRA_SHIFT, x4, x5, x6
 #else
+#define IDMAP_PGD_ORDER	(PHYS_MASK_SHIFT - PGDIR_SHIFT)
+#define EXTRA_SHIFT
 	/*
 	 * If VA_BITS == 48, we don't have to configure an additional
 	 * translation level, but the top-level table has more entries.
 	 */
-	mov	x4, #1 << (PHYS_MASK_SHIFT - PGDIR_SHIFT)
-	str_l	x4, idmap_ptrs_per_pgd, x5
 #endif
-1:
-	ldr_l	x4, idmap_ptrs_per_pgd
-	adr_l	x6, __idmap_text_end		// __pa(__idmap_text_end)
-
-	map_memory x0, x1, x3, x6, x7, x3, x4, x10, x11, x12, x13, x14
-
-	/*
-	 * Map the kernel image (starting with PHYS_OFFSET).
-	 */
-	adrp	x0, init_pg_dir
-	mov_q	x5, KIMAGE_VADDR		// compile time __va(_text)
-	add	x5, x5, x23			// add KASLR displacement
-	mov	x4, PTRS_PER_PGD
-	adrp	x6, _end			// runtime __pa(_end)
-	adrp	x3, _text			// runtime __pa(_text)
-	sub	x6, x6, x3			// _end - _text
-	add	x6, x6, x5			// runtime __va(_end)
-
-	map_memory x0, x1, x5, x6, x7, x3, x4, x10, x11, x12, x13, x14
+	adrp	x0, init_idmap_pg_dir
+	adrp	x3, _text
+	adrp	x6, _end + MAX_FDT_SIZE + SWAPPER_BLOCK_SIZE
+	mov	x7, SWAPPER_RX_MMUFLAGS
+
+	map_memory x0, x1, x3, x6, x7, x3, IDMAP_PGD_ORDER, x10, x11, x12, x13, x14, EXTRA_SHIFT
+
+	/* Remap the kernel page tables r/w in the ID map */
+	adrp	x1, _text
+	adrp	x2, init_pg_dir
+	adrp	x3, init_pg_end
+	bic	x4, x2, #SWAPPER_BLOCK_SIZE - 1
+	mov	x5, SWAPPER_RW_MMUFLAGS
+	mov	x6, #SWAPPER_BLOCK_SHIFT
+	bl	remap_region
+
+	/* Remap the FDT after the kernel image */
+	adrp	x1, _text
+	adrp	x22, _end + SWAPPER_BLOCK_SIZE
+	bic	x2, x22, #SWAPPER_BLOCK_SIZE - 1
+	bfi	x22, x21, #0, #SWAPPER_BLOCK_SHIFT		// remapped FDT address
+	add	x3, x2, #MAX_FDT_SIZE + SWAPPER_BLOCK_SIZE
+	bic	x4, x21, #SWAPPER_BLOCK_SIZE - 1
+	mov	x5, SWAPPER_RW_MMUFLAGS
+	mov	x6, #SWAPPER_BLOCK_SHIFT
+	bl	remap_region
 
 	/*
 	 * Since the page tables have been populated with non-cacheable
@@ -380,16 +362,29 @@ SYM_FUNC_START_LOCAL(__create_page_tables)
 	 */
 	dmb	sy
 
-	adrp	x0, idmap_pg_dir
-	adrp	x1, idmap_pg_end
+	adrp	x0, init_idmap_pg_dir
+	adrp	x1, init_idmap_pg_end
 	bl	dcache_inval_poc
+	ret	x28
+SYM_FUNC_END(create_idmap)
 
+SYM_FUNC_START_LOCAL(create_kernel_mapping)
 	adrp	x0, init_pg_dir
-	adrp	x1, init_pg_end
-	bl	dcache_inval_poc
+	mov_q	x5, KIMAGE_VADDR		// compile time __va(_text)
+#ifdef CONFIG_RELOCATABLE
+	add	x5, x5, x23			// add KASLR displacement
+#endif
+	adrp	x6, _end			// runtime __pa(_end)
+	adrp	x3, _text			// runtime __pa(_text)
+	sub	x6, x6, x3			// _end - _text
+	add	x6, x6, x5			// runtime __va(_end)
+	mov	x7, SWAPPER_RW_MMUFLAGS
 
-	ret	x28
-SYM_FUNC_END(__create_page_tables)
+	map_memory x0, x1, x5, x6, x7, x3, (VA_BITS - PGDIR_SHIFT), x10, x11, x12, x13, x14
+
+	dsb	ishst				// sync with page table walker
+	ret
+SYM_FUNC_END(create_kernel_mapping)
 
 	/*
 	 * Initialize CPU registers with task-specific and cpu-specific context.
@@ -420,7 +415,7 @@ SYM_FUNC_END(__create_page_tables)
 /*
  * The following fragment of code is executed with the MMU enabled.
  *
- *   x0 = __PHYS_OFFSET
+ *   x0 = __pa(KERNEL_START)
  */
 SYM_FUNC_START_LOCAL(__primary_switched)
 	adr_l	x4, init_task
@@ -439,6 +434,9 @@ SYM_FUNC_START_LOCAL(__primary_switched)
 	sub	x4, x4, x0			// the kernel virtual and
 	str_l	x4, kimage_voffset, x5		// physical mappings
 
+	mov	x0, x20
+	bl	set_cpu_boot_mode_flag
+
 	// Clear BSS
 	adr_l	x0, __bss_start
 	mov	x1, xzr
@@ -447,35 +445,30 @@ SYM_FUNC_START_LOCAL(__primary_switched)
 	bl	__pi_memset
 	dsb	ishst				// Make zero page visible to PTW
 
+#if VA_BITS > 48
+	adr_l	x8, vabits_actual		// Set this early so KASAN early init
+	str	x25, [x8]			// ... observes the correct value
+	dc	civac, x8			// Make visible to booting secondaries
+#endif
+
+#ifdef CONFIG_RANDOMIZE_BASE
+	adrp	x5, memstart_offset_seed	// Save KASLR linear map seed
+	strh	w24, [x5, :lo12:memstart_offset_seed]
+#endif
 #if defined(CONFIG_KASAN_GENERIC) || defined(CONFIG_KASAN_SW_TAGS)
 	bl	kasan_early_init
 #endif
 	mov	x0, x21				// pass FDT address in x0
 	bl	early_fdt_map			// Try mapping the FDT early
+	mov	x0, x20				// pass the full boot status
 	bl	init_feature_override		// Parse cpu feature overrides
-#ifdef CONFIG_RANDOMIZE_BASE
-	tst	x23, ~(MIN_KIMG_ALIGN - 1)	// already running randomized?
-	b.ne	0f
-	bl	kaslr_early_init		// parse FDT for KASLR options
-	cbz	x0, 0f				// KASLR disabled? just proceed
-	orr	x23, x23, x0			// record KASLR offset
-	ldp	x29, x30, [sp], #16		// we must enable KASLR, return
-	ret					// to __primary_switch()
-0:
-#endif
-	bl	switch_to_vhe			// Prefer VHE if possible
+	mov	x0, x20
+	bl	finalise_el2			// Prefer VHE if possible
 	ldp	x29, x30, [sp], #16
 	bl	start_kernel
 	ASM_BUG()
 SYM_FUNC_END(__primary_switched)
 
-	.pushsection ".rodata", "a"
-SYM_DATA_START(kimage_vaddr)
-	.quad		_text
-SYM_DATA_END(kimage_vaddr)
-EXPORT_SYMBOL(kimage_vaddr)
-	.popsection
-
 /*
  * end early head section, begin head code that is also used for
  * hotplug and needs to have the same protections as the text region
@@ -490,8 +483,9 @@ EXPORT_SYMBOL(kimage_vaddr)
  * Since we cannot always rely on ERET synchronizing writes to sysregs (e.g. if
  * SCTLR_ELx.EOS is clear), we place an ISB prior to ERET.
  *
- * Returns either BOOT_CPU_MODE_EL1 or BOOT_CPU_MODE_EL2 in w0 if
- * booted in EL1 or EL2 respectively.
+ * Returns either BOOT_CPU_MODE_EL1 or BOOT_CPU_MODE_EL2 in x0 if
+ * booted in EL1 or EL2 respectively, with the top 32 bits containing
+ * potential context flags. These flags are *not* stored in __boot_cpu_mode.
  */
 SYM_FUNC_START(init_kernel_el)
 	mrs	x0, CurrentEL
@@ -520,6 +514,8 @@ SYM_INNER_LABEL(init_el2, SYM_L_LOCAL)
 	msr	vbar_el2, x0
 	isb
 
+	mov_q	x1, INIT_SCTLR_EL1_MMU_OFF
+
 	/*
 	 * Fruity CPUs seem to have HCR_EL2.E2H set to RES1,
 	 * making it impossible to start in nVHE mode. Is that
@@ -529,34 +525,19 @@ SYM_INNER_LABEL(init_el2, SYM_L_LOCAL)
 	and	x0, x0, #HCR_E2H
 	cbz	x0, 1f
 
-	/* Switching to VHE requires a sane SCTLR_EL1 as a start */
-	mov_q	x0, INIT_SCTLR_EL1_MMU_OFF
-	msr_s	SYS_SCTLR_EL12, x0
-
-	/*
-	 * Force an eret into a helper "function", and let it return
-	 * to our original caller... This makes sure that we have
-	 * initialised the basic PSTATE state.
-	 */
-	mov	x0, #INIT_PSTATE_EL2
-	msr	spsr_el1, x0
-	adr	x0, __cpu_stick_to_vhe
-	msr	elr_el1, x0
-	eret
+	/* Set a sane SCTLR_EL1, the VHE way */
+	msr_s	SYS_SCTLR_EL12, x1
+	mov	x2, #BOOT_CPU_FLAG_E2H
+	b	2f
 
 1:
-	mov_q	x0, INIT_SCTLR_EL1_MMU_OFF
-	msr	sctlr_el1, x0
-
+	msr	sctlr_el1, x1
+	mov	x2, xzr
+2:
 	msr	elr_el2, lr
 	mov	w0, #BOOT_CPU_MODE_EL2
+	orr	x0, x0, x2
 	eret
-
-__cpu_stick_to_vhe:
-	mov	x0, #HVC_VHE_RESTART
-	hvc	#0
-	mov	x0, #BOOT_CPU_MODE_EL2
-	ret
 SYM_FUNC_END(init_kernel_el)
 
 /*
@@ -569,52 +550,21 @@ SYM_FUNC_START_LOCAL(set_cpu_boot_mode_flag)
 	b.ne	1f
 	add	x1, x1, #4
 1:	str	w0, [x1]			// Save CPU boot mode
-	dmb	sy
-	dc	ivac, x1			// Invalidate potentially stale cache line
 	ret
 SYM_FUNC_END(set_cpu_boot_mode_flag)
 
-/*
- * These values are written with the MMU off, but read with the MMU on.
- * Writers will invalidate the corresponding address, discarding up to a
- * 'Cache Writeback Granule' (CWG) worth of data. The linker script ensures
- * sufficient alignment that the CWG doesn't overlap another section.
- */
-	.pushsection ".mmuoff.data.write", "aw"
-/*
- * We need to find out the CPU boot mode long after boot, so we need to
- * store it in a writable variable.
- *
- * This is not in .bss, because we set it sufficiently early that the boot-time
- * zeroing of .bss would clobber it.
- */
-SYM_DATA_START(__boot_cpu_mode)
-	.long	BOOT_CPU_MODE_EL2
-	.long	BOOT_CPU_MODE_EL1
-SYM_DATA_END(__boot_cpu_mode)
-/*
- * The booting CPU updates the failed status @__early_cpu_boot_status,
- * with MMU turned off.
- */
-SYM_DATA_START(__early_cpu_boot_status)
-	.quad 	0
-SYM_DATA_END(__early_cpu_boot_status)
-
-	.popsection
-
 	/*
 	 * This provides a "holding pen" for platforms to hold all secondary
 	 * cores are held until we're ready for them to initialise.
 	 */
 SYM_FUNC_START(secondary_holding_pen)
 	bl	init_kernel_el			// w0=cpu_boot_mode
-	bl	set_cpu_boot_mode_flag
-	mrs	x0, mpidr_el1
+	mrs	x2, mpidr_el1
 	mov_q	x1, MPIDR_HWID_BITMASK
-	and	x0, x0, x1
+	and	x2, x2, x1
 	adr_l	x3, secondary_holding_pen_release
 pen:	ldr	x4, [x3]
-	cmp	x4, x0
+	cmp	x4, x2
 	b.eq	secondary_startup
 	wfe
 	b	pen
@@ -626,7 +576,6 @@ SYM_FUNC_END(secondary_holding_pen)
 	 */
 SYM_FUNC_START(secondary_entry)
 	bl	init_kernel_el			// w0=cpu_boot_mode
-	bl	set_cpu_boot_mode_flag
 	b	secondary_startup
 SYM_FUNC_END(secondary_entry)
 
@@ -634,16 +583,24 @@ SYM_FUNC_START_LOCAL(secondary_startup)
 	/*
 	 * Common entry point for secondary CPUs.
 	 */
-	bl	switch_to_vhe
+	mov	x20, x0				// preserve boot mode
+	bl	finalise_el2
 	bl	__cpu_secondary_check52bitva
+#if VA_BITS > 48
+	ldr_l	x0, vabits_actual
+#endif
 	bl	__cpu_setup			// initialise processor
 	adrp	x1, swapper_pg_dir
+	adrp	x2, idmap_pg_dir
 	bl	__enable_mmu
 	ldr	x8, =__secondary_switched
 	br	x8
 SYM_FUNC_END(secondary_startup)
 
 SYM_FUNC_START_LOCAL(__secondary_switched)
+	mov	x0, x20
+	bl	set_cpu_boot_mode_flag
+	str_l	xzr, __early_cpu_boot_status, x3
 	adr_l	x5, vectors
 	msr	vbar_el1, x5
 	isb
@@ -691,6 +648,7 @@ SYM_FUNC_END(__secondary_too_slow)
  *
  *  x0  = SCTLR_EL1 value for turning on the MMU.
  *  x1  = TTBR1_EL1 value
+ *  x2  = ID map root table address
  *
  * Returns to the caller via x30/lr. This requires the caller to be covered
  * by the .idmap.text section.
@@ -699,20 +657,15 @@ SYM_FUNC_END(__secondary_too_slow)
  * If it isn't, park the CPU
  */
 SYM_FUNC_START(__enable_mmu)
-	mrs	x2, ID_AA64MMFR0_EL1
-	ubfx	x2, x2, #ID_AA64MMFR0_TGRAN_SHIFT, 4
-	cmp     x2, #ID_AA64MMFR0_TGRAN_SUPPORTED_MIN
+	mrs	x3, ID_AA64MMFR0_EL1
+	ubfx	x3, x3, #ID_AA64MMFR0_EL1_TGRAN_SHIFT, 4
+	cmp     x3, #ID_AA64MMFR0_EL1_TGRAN_SUPPORTED_MIN
 	b.lt    __no_granule_support
-	cmp     x2, #ID_AA64MMFR0_TGRAN_SUPPORTED_MAX
+	cmp     x3, #ID_AA64MMFR0_EL1_TGRAN_SUPPORTED_MAX
 	b.gt    __no_granule_support
-	update_early_cpu_boot_status 0, x2, x3
-	adrp	x2, idmap_pg_dir
-	phys_to_ttbr x1, x1
 	phys_to_ttbr x2, x2
 	msr	ttbr0_el1, x2			// load TTBR0
-	offset_ttbr1 x1, x3
-	msr	ttbr1_el1, x1			// load TTBR1
-	isb
+	load_ttbr1 x1, x1, x3
 
 	set_sctlr_el1	x0
 
@@ -720,13 +673,13 @@ SYM_FUNC_START(__enable_mmu)
 SYM_FUNC_END(__enable_mmu)
 
 SYM_FUNC_START(__cpu_secondary_check52bitva)
-#ifdef CONFIG_ARM64_VA_BITS_52
+#if VA_BITS > 48
 	ldr_l	x0, vabits_actual
 	cmp	x0, #52
 	b.ne	2f
 
 	mrs_s	x0, SYS_ID_AA64MMFR2_EL1
-	and	x0, x0, #(0xf << ID_AA64MMFR2_LVA_SHIFT)
+	and	x0, x0, #(0xf << ID_AA64MMFR2_EL1_VARange_SHIFT)
 	cbnz	x0, 2f
 
 	update_early_cpu_boot_status \
@@ -755,13 +708,10 @@ SYM_FUNC_START_LOCAL(__relocate_kernel)
 	 * Iterate over each entry in the relocation table, and apply the
 	 * relocations in place.
 	 */
-	ldr	w9, =__rela_offset		// offset to reloc table
-	ldr	w10, =__rela_size		// size of reloc table
-
+	adr_l	x9, __rela_start
+	adr_l	x10, __rela_end
 	mov_q	x11, KIMAGE_VADDR		// default virtual offset
 	add	x11, x11, x23			// actual virtual offset
-	add	x9, x9, x11			// __va(.rela)
-	add	x10, x9, x10			// __va(.rela) + sizeof(.rela)
 
 0:	cmp	x9, x10
 	b.hs	1f
@@ -804,21 +754,9 @@ SYM_FUNC_START_LOCAL(__relocate_kernel)
 	 * entry in x9, the address being relocated by the current address or
 	 * bitmap entry in x13 and the address being relocated by the current
 	 * bit in x14.
-	 *
-	 * Because addends are stored in place in the binary, RELR relocations
-	 * cannot be applied idempotently. We use x24 to keep track of the
-	 * currently applied displacement so that we can correctly relocate if
-	 * __relocate_kernel is called twice with non-zero displacements (i.e.
-	 * if there is both a physical misalignment and a KASLR displacement).
 	 */
-	ldr	w9, =__relr_offset		// offset to reloc table
-	ldr	w10, =__relr_size		// size of reloc table
-	add	x9, x9, x11			// __va(.relr)
-	add	x10, x9, x10			// __va(.relr) + sizeof(.relr)
-
-	sub	x15, x23, x24			// delta from previous offset
-	cbz	x15, 7f				// nothing to do if unchanged
-	mov	x24, x23			// save new offset
+	adr_l	x9, __relr_start
+	adr_l	x10, __relr_end
 
 2:	cmp	x9, x10
 	b.hs	7f
@@ -826,7 +764,7 @@ SYM_FUNC_START_LOCAL(__relocate_kernel)
 	tbnz	x11, #0, 3f			// branch to handle bitmaps
 	add	x13, x11, x23
 	ldr	x12, [x13]			// relocate address entry
-	add	x12, x12, x15
+	add	x12, x12, x23
 	str	x12, [x13], #8			// adjust to start of bitmap
 	b	2b
 
@@ -835,7 +773,7 @@ SYM_FUNC_START_LOCAL(__relocate_kernel)
 	cbz	x11, 6f
 	tbz	x11, #0, 5f			// skip bit if not set
 	ldr	x12, [x14]			// relocate bit
-	add	x12, x12, x15
+	add	x12, x12, x23
 	str	x12, [x14]
 
 5:	add	x14, x14, #8			// move to next bit's address
@@ -856,43 +794,32 @@ SYM_FUNC_END(__relocate_kernel)
 #endif
 
 SYM_FUNC_START_LOCAL(__primary_switch)
+	adrp	x1, reserved_pg_dir
+	adrp	x2, init_idmap_pg_dir
+	bl	__enable_mmu
+#ifdef CONFIG_RELOCATABLE
+	adrp	x23, KERNEL_START
+	and	x23, x23, MIN_KIMG_ALIGN - 1
 #ifdef CONFIG_RANDOMIZE_BASE
-	mov	x19, x0				// preserve new SCTLR_EL1 value
-	mrs	x20, sctlr_el1			// preserve old SCTLR_EL1 value
+	mov	x0, x22
+	adrp	x1, init_pg_end
+	mov	sp, x1
+	mov	x29, xzr
+	bl	__pi_kaslr_early_init
+	and	x24, x0, #SZ_2M - 1		// capture memstart offset seed
+	bic	x0, x0, #SZ_2M - 1
+	orr	x23, x23, x0			// record kernel offset
+#endif
 #endif
+	bl	clear_page_tables
+	bl	create_kernel_mapping
 
 	adrp	x1, init_pg_dir
-	bl	__enable_mmu
+	load_ttbr1 x1, x1, x2
 #ifdef CONFIG_RELOCATABLE
-#ifdef CONFIG_RELR
-	mov	x24, #0				// no RELR displacement yet
-#endif
 	bl	__relocate_kernel
-#ifdef CONFIG_RANDOMIZE_BASE
-	ldr	x8, =__primary_switched
-	adrp	x0, __PHYS_OFFSET
-	blr	x8
-
-	/*
-	 * If we return here, we have a KASLR displacement in x23 which we need
-	 * to take into account by discarding the current kernel mapping and
-	 * creating a new one.
-	 */
-	pre_disable_mmu_workaround
-	msr	sctlr_el1, x20			// disable the MMU
-	isb
-	bl	__create_page_tables		// recreate kernel mapping
-
-	tlbi	vmalle1				// Remove any stale TLB entries
-	dsb	nsh
-	isb
-
-	set_sctlr_el1	x19			// re-enable the MMU
-
-	bl	__relocate_kernel
-#endif
 #endif
 	ldr	x8, =__primary_switched
-	adrp	x0, __PHYS_OFFSET
+	adrp	x0, KERNEL_START		// __pa(KERNEL_START)
 	br	x8
 SYM_FUNC_END(__primary_switch)
diff --git a/arch/arm64/kernel/hibernate.c b/arch/arm64/kernel/hibernate.c
index 2758f75d6809..af5df48ba915 100644
--- a/arch/arm64/kernel/hibernate.c
+++ b/arch/arm64/kernel/hibernate.c
@@ -7,10 +7,6 @@
  * Ubuntu project, hibernation support for mach-dove
  * Copyright (C) 2010 Nokia Corporation (Hiroshi Doyu)
  * Copyright (C) 2010 Texas Instruments, Inc. (Teerth Reddy et al.)
- *  https://lkml.org/lkml/2010/6/18/4
- *  https://lists.linux-foundation.org/pipermail/linux-pm/2010-June/027422.html
- *  https://patchwork.kernel.org/patch/96442/
- *
  * Copyright (C) 2006 Rafael J. Wysocki <rjw@sisk.pl>
  */
 #define pr_fmt(x) "hibernate: " x
@@ -304,11 +300,6 @@ static void swsusp_mte_restore_tags(void)
 		unsigned long pfn = xa_state.xa_index;
 		struct page *page = pfn_to_online_page(pfn);
 
-		/*
-		 * It is not required to invoke page_kasan_tag_reset(page)
-		 * at this point since the tags stored in page->flags are
-		 * already restored.
-		 */
 		mte_restore_page_tags(page_address(page), tags);
 
 		mte_free_tag_storage(tags);
@@ -431,7 +422,7 @@ int swsusp_arch_resume(void)
 		return rc;
 
 	/*
-	 * We need a zero page that is zero before & after resume in order to
+	 * We need a zero page that is zero before & after resume in order
 	 * to break before make on the ttbr1 page tables.
 	 */
 	zero_page = (void *)get_safe_page(GFP_ATOMIC);
diff --git a/arch/arm64/kernel/hw_breakpoint.c b/arch/arm64/kernel/hw_breakpoint.c
index 712e97c03e54..b29a311bb055 100644
--- a/arch/arm64/kernel/hw_breakpoint.c
+++ b/arch/arm64/kernel/hw_breakpoint.c
@@ -617,7 +617,7 @@ NOKPROBE_SYMBOL(toggle_bp_registers);
 /*
  * Debug exception handlers.
  */
-static int breakpoint_handler(unsigned long unused, unsigned int esr,
+static int breakpoint_handler(unsigned long unused, unsigned long esr,
 			      struct pt_regs *regs)
 {
 	int i, step = 0, *kernel_step;
@@ -701,7 +701,7 @@ NOKPROBE_SYMBOL(breakpoint_handler);
  * addresses. There is no straight-forward way, short of disassembling the
  * offending instruction, to map that address back to the watchpoint. This
  * function computes the distance of the memory access from the watchpoint as a
- * heuristic for the likelyhood that a given access triggered the watchpoint.
+ * heuristic for the likelihood that a given access triggered the watchpoint.
  *
  * See Section D2.10.5 "Determining the memory location that caused a Watchpoint
  * exception" of ARMv8 Architecture Reference Manual for details.
@@ -751,7 +751,7 @@ static int watchpoint_report(struct perf_event *wp, unsigned long addr,
 	return step;
 }
 
-static int watchpoint_handler(unsigned long addr, unsigned int esr,
+static int watchpoint_handler(unsigned long addr, unsigned long esr,
 			      struct pt_regs *regs)
 {
 	int i, step = 0, *kernel_step, access, closest_match = 0;
diff --git a/arch/arm64/kernel/hyp-stub.S b/arch/arm64/kernel/hyp-stub.S
index 43d212618834..2ee18c860f2a 100644
--- a/arch/arm64/kernel/hyp-stub.S
+++ b/arch/arm64/kernel/hyp-stub.S
@@ -16,6 +16,30 @@
 #include <asm/ptrace.h>
 #include <asm/virt.h>
 
+// Warning, hardcoded register allocation
+// This will clobber x1 and x2, and expect x1 to contain
+// the id register value as read from the HW
+.macro __check_override idreg, fld, width, pass, fail
+	ubfx	x1, x1, #\fld, #\width
+	cbz	x1, \fail
+
+	adr_l	x1, \idreg\()_override
+	ldr	x2, [x1, FTR_OVR_VAL_OFFSET]
+	ldr	x1, [x1, FTR_OVR_MASK_OFFSET]
+	ubfx	x2, x2, #\fld, #\width
+	ubfx	x1, x1, #\fld, #\width
+	cmp	x1, xzr
+	and	x2, x2, x1
+	csinv	x2, x2, xzr, ne
+	cbnz	x2, \pass
+	b	\fail
+.endm
+
+.macro check_override idreg, fld, pass, fail
+	mrs	x1, \idreg\()_el1
+	__check_override \idreg \fld 4 \pass \fail
+.endm
+
 	.text
 	.pushsection	.hyp.text, "ax"
 
@@ -51,8 +75,8 @@ SYM_CODE_START_LOCAL(elx_sync)
 	msr	vbar_el2, x1
 	b	9f
 
-1:	cmp	x0, #HVC_VHE_RESTART
-	b.eq	mutate_to_vhe
+1:	cmp	x0, #HVC_FINALISE_EL2
+	b.eq	__finalise_el2
 
 2:	cmp	x0, #HVC_SOFT_RESTART
 	b.ne	3f
@@ -73,27 +97,67 @@ SYM_CODE_START_LOCAL(elx_sync)
 	eret
 SYM_CODE_END(elx_sync)
 
-// nVHE? No way! Give me the real thing!
-SYM_CODE_START_LOCAL(mutate_to_vhe)
+SYM_CODE_START_LOCAL(__finalise_el2)
+	check_override id_aa64pfr0 ID_AA64PFR0_EL1_SVE_SHIFT .Linit_sve .Lskip_sve
+
+.Linit_sve:	/* SVE register access */
+	mrs	x0, cptr_el2			// Disable SVE traps
+	bic	x0, x0, #CPTR_EL2_TZ
+	msr	cptr_el2, x0
+	isb
+	mov	x1, #ZCR_ELx_LEN_MASK		// SVE: Enable full vector
+	msr_s	SYS_ZCR_EL2, x1			// length for EL1.
+
+.Lskip_sve:
+	check_override id_aa64pfr1 ID_AA64PFR1_EL1_SME_SHIFT .Linit_sme .Lskip_sme
+
+.Linit_sme:	/* SME register access and priority mapping */
+	mrs	x0, cptr_el2			// Disable SME traps
+	bic	x0, x0, #CPTR_EL2_TSM
+	msr	cptr_el2, x0
+	isb
+
+	mrs	x1, sctlr_el2
+	orr	x1, x1, #SCTLR_ELx_ENTP2	// Disable TPIDR2 traps
+	msr	sctlr_el2, x1
+	isb
+
+	mov	x0, #0				// SMCR controls
+
+	// Full FP in SM?
+	mrs_s	x1, SYS_ID_AA64SMFR0_EL1
+	__check_override id_aa64smfr0 ID_AA64SMFR0_EL1_FA64_SHIFT 1 .Linit_sme_fa64 .Lskip_sme_fa64
+
+.Linit_sme_fa64:
+	orr	x0, x0, SMCR_ELx_FA64_MASK
+.Lskip_sme_fa64:
+
+	orr	x0, x0, #SMCR_ELx_LEN_MASK	// Enable full SME vector
+	msr_s	SYS_SMCR_EL2, x0		// length for EL1.
+
+	mrs_s	x1, SYS_SMIDR_EL1		// Priority mapping supported?
+	ubfx    x1, x1, #SMIDR_EL1_SMPS_SHIFT, #1
+	cbz     x1, .Lskip_sme
+
+	msr_s	SYS_SMPRIMAP_EL2, xzr		// Make all priorities equal
+
+	mrs	x1, id_aa64mmfr1_el1		// HCRX_EL2 present?
+	ubfx	x1, x1, #ID_AA64MMFR1_EL1_HCX_SHIFT, #4
+	cbz	x1, .Lskip_sme
+
+	mrs_s	x1, SYS_HCRX_EL2
+	orr	x1, x1, #HCRX_EL2_SMPME_MASK	// Enable priority mapping
+	msr_s	SYS_HCRX_EL2, x1
+
+.Lskip_sme:
+
+	// nVHE? No way! Give me the real thing!
 	// Sanity check: MMU *must* be off
 	mrs	x1, sctlr_el2
 	tbnz	x1, #0, 1f
 
 	// Needs to be VHE capable, obviously
-	mrs	x1, id_aa64mmfr1_el1
-	ubfx	x1, x1, #ID_AA64MMFR1_VHE_SHIFT, #4
-	cbz	x1, 1f
-
-	// Check whether VHE is disabled from the command line
-	adr_l	x1, id_aa64mmfr1_override
-	ldr	x2, [x1, FTR_OVR_VAL_OFFSET]
-	ldr	x1, [x1, FTR_OVR_MASK_OFFSET]
-	ubfx	x2, x2, #ID_AA64MMFR1_VHE_SHIFT, #4
-	ubfx	x1, x1, #ID_AA64MMFR1_VHE_SHIFT, #4
-	cmp	x1, xzr
-	and	x2, x2, x1
-	csinv	x2, x2, xzr, ne
-	cbnz	x2, 2f
+	check_override id_aa64mmfr1 ID_AA64MMFR1_EL1_VH_SHIFT 2f 1f
 
 1:	mov_q	x0, HVC_STUB_ERR
 	eret
@@ -140,10 +204,10 @@ SYM_CODE_START_LOCAL(mutate_to_vhe)
 	msr	spsr_el1, x0
 
 	b	enter_vhe
-SYM_CODE_END(mutate_to_vhe)
+SYM_CODE_END(__finalise_el2)
 
 	// At the point where we reach enter_vhe(), we run with
-	// the MMU off (which is enforced by mutate_to_vhe()).
+	// the MMU off (which is enforced by __finalise_el2()).
 	// We thus need to be in the idmap, or everything will
 	// explode when enabling the MMU.
 
@@ -222,12 +286,12 @@ SYM_FUNC_START(__hyp_reset_vectors)
 SYM_FUNC_END(__hyp_reset_vectors)
 
 /*
- * Entry point to switch to VHE if deemed capable
+ * Entry point to finalise EL2 and switch to VHE if deemed capable
+ *
+ * w0: boot mode, as returned by init_kernel_el()
  */
-SYM_FUNC_START(switch_to_vhe)
+SYM_FUNC_START(finalise_el2)
 	// Need to have booted at EL2
-	adr_l	x1, __boot_cpu_mode
-	ldr	w0, [x1]
 	cmp	w0, #BOOT_CPU_MODE_EL2
 	b.ne	1f
 
@@ -236,9 +300,8 @@ SYM_FUNC_START(switch_to_vhe)
 	cmp	x0, #CurrentEL_EL1
 	b.ne	1f
 
-	// Turn the world upside down
-	mov	x0, #HVC_VHE_RESTART
+	mov	x0, #HVC_FINALISE_EL2
 	hvc	#0
 1:
 	ret
-SYM_FUNC_END(switch_to_vhe)
+SYM_FUNC_END(finalise_el2)
diff --git a/arch/arm64/kernel/idreg-override.c b/arch/arm64/kernel/idreg-override.c
index d8e606fe3c21..95133765ed29 100644
--- a/arch/arm64/kernel/idreg-override.c
+++ b/arch/arm64/kernel/idreg-override.c
@@ -17,7 +17,9 @@
 #define FTR_DESC_NAME_LEN	20
 #define FTR_DESC_FIELD_LEN	10
 #define FTR_ALIAS_NAME_LEN	30
-#define FTR_ALIAS_OPTION_LEN	80
+#define FTR_ALIAS_OPTION_LEN	116
+
+static u64 __boot_status __initdata;
 
 struct ftr_set_desc {
 	char 				name[FTR_DESC_NAME_LEN];
@@ -25,10 +27,13 @@ struct ftr_set_desc {
 	struct {
 		char			name[FTR_DESC_FIELD_LEN];
 		u8			shift;
+		u8			width;
 		bool			(*filter)(u64 val);
 	} 				fields[];
 };
 
+#define FIELD(n, s, f)	{ .name = n, .shift = s, .width = 4, .filter = f }
+
 static bool __init mmfr1_vh_filter(u64 val)
 {
 	/*
@@ -37,24 +42,65 @@ static bool __init mmfr1_vh_filter(u64 val)
 	 * the user was trying to force nVHE on us, proceed with
 	 * attitude adjustment.
 	 */
-	return !(is_kernel_in_hyp_mode() && val == 0);
+	return !(__boot_status == (BOOT_CPU_FLAG_E2H | BOOT_CPU_MODE_EL2) &&
+		 val == 0);
 }
 
 static const struct ftr_set_desc mmfr1 __initconst = {
 	.name		= "id_aa64mmfr1",
 	.override	= &id_aa64mmfr1_override,
 	.fields		= {
-		{ "vh", ID_AA64MMFR1_VHE_SHIFT, mmfr1_vh_filter },
+		FIELD("vh", ID_AA64MMFR1_EL1_VH_SHIFT, mmfr1_vh_filter),
+		{}
+	},
+};
+
+static bool __init pfr0_sve_filter(u64 val)
+{
+	/*
+	 * Disabling SVE also means disabling all the features that
+	 * are associated with it. The easiest way to do it is just to
+	 * override id_aa64zfr0_el1 to be 0.
+	 */
+	if (!val) {
+		id_aa64zfr0_override.val = 0;
+		id_aa64zfr0_override.mask = GENMASK(63, 0);
+	}
+
+	return true;
+}
+
+static const struct ftr_set_desc pfr0 __initconst = {
+	.name		= "id_aa64pfr0",
+	.override	= &id_aa64pfr0_override,
+	.fields		= {
+	        FIELD("sve", ID_AA64PFR0_EL1_SVE_SHIFT, pfr0_sve_filter),
 		{}
 	},
 };
 
+static bool __init pfr1_sme_filter(u64 val)
+{
+	/*
+	 * Similarly to SVE, disabling SME also means disabling all
+	 * the features that are associated with it. Just set
+	 * id_aa64smfr0_el1 to 0 and don't look back.
+	 */
+	if (!val) {
+		id_aa64smfr0_override.val = 0;
+		id_aa64smfr0_override.mask = GENMASK(63, 0);
+	}
+
+	return true;
+}
+
 static const struct ftr_set_desc pfr1 __initconst = {
 	.name		= "id_aa64pfr1",
 	.override	= &id_aa64pfr1_override,
 	.fields		= {
-	        { "bt", ID_AA64PFR1_BT_SHIFT },
-		{ "mte", ID_AA64PFR1_MTE_SHIFT},
+		FIELD("bt", ID_AA64PFR1_EL1_BT_SHIFT, NULL ),
+		FIELD("mte", ID_AA64PFR1_EL1_MTE_SHIFT, NULL),
+		FIELD("sme", ID_AA64PFR1_EL1_SME_SHIFT, pfr1_sme_filter),
 		{}
 	},
 };
@@ -63,10 +109,30 @@ static const struct ftr_set_desc isar1 __initconst = {
 	.name		= "id_aa64isar1",
 	.override	= &id_aa64isar1_override,
 	.fields		= {
-	        { "gpi", ID_AA64ISAR1_GPI_SHIFT },
-	        { "gpa", ID_AA64ISAR1_GPA_SHIFT },
-	        { "api", ID_AA64ISAR1_API_SHIFT },
-	        { "apa", ID_AA64ISAR1_APA_SHIFT },
+		FIELD("gpi", ID_AA64ISAR1_EL1_GPI_SHIFT, NULL),
+		FIELD("gpa", ID_AA64ISAR1_EL1_GPA_SHIFT, NULL),
+		FIELD("api", ID_AA64ISAR1_EL1_API_SHIFT, NULL),
+		FIELD("apa", ID_AA64ISAR1_EL1_APA_SHIFT, NULL),
+		{}
+	},
+};
+
+static const struct ftr_set_desc isar2 __initconst = {
+	.name		= "id_aa64isar2",
+	.override	= &id_aa64isar2_override,
+	.fields		= {
+		FIELD("gpa3", ID_AA64ISAR2_EL1_GPA3_SHIFT, NULL),
+		FIELD("apa3", ID_AA64ISAR2_EL1_APA3_SHIFT, NULL),
+		{}
+	},
+};
+
+static const struct ftr_set_desc smfr0 __initconst = {
+	.name		= "id_aa64smfr0",
+	.override	= &id_aa64smfr0_override,
+	.fields		= {
+		/* FA64 is a one bit field... :-/ */
+		{ "fa64", ID_AA64SMFR0_EL1_FA64_SHIFT, 1, },
 		{}
 	},
 };
@@ -79,15 +145,18 @@ static const struct ftr_set_desc kaslr __initconst = {
 	.override	= &kaslr_feature_override,
 #endif
 	.fields		= {
-		{ "disabled", 0 },
+		FIELD("disabled", 0, NULL),
 		{}
 	},
 };
 
 static const struct ftr_set_desc * const regs[] __initconst = {
 	&mmfr1,
+	&pfr0,
 	&pfr1,
 	&isar1,
+	&isar2,
+	&smfr0,
 	&kaslr,
 };
 
@@ -97,10 +166,13 @@ static const struct {
 } aliases[] __initconst = {
 	{ "kvm-arm.mode=nvhe",		"id_aa64mmfr1.vh=0" },
 	{ "kvm-arm.mode=protected",	"id_aa64mmfr1.vh=0" },
+	{ "arm64.nosve",		"id_aa64pfr0.sve=0 id_aa64pfr1.sme=0" },
+	{ "arm64.nosme",		"id_aa64pfr1.sme=0" },
 	{ "arm64.nobti",		"id_aa64pfr1.bt=0" },
 	{ "arm64.nopauth",
 	  "id_aa64isar1.gpi=0 id_aa64isar1.gpa=0 "
-	  "id_aa64isar1.api=0 id_aa64isar1.apa=0"	   },
+	  "id_aa64isar1.api=0 id_aa64isar1.apa=0 "
+	  "id_aa64isar2.gpa3=0 id_aa64isar2.apa3=0"	   },
 	{ "arm64.nomte",		"id_aa64pfr1.mte=0" },
 	{ "nokaslr",			"kaslr.disabled=1" },
 };
@@ -132,7 +204,8 @@ static void __init match_options(const char *cmdline)
 
 		for (f = 0; strlen(regs[i]->fields[f].name); f++) {
 			u64 shift = regs[i]->fields[f].shift;
-			u64 mask = 0xfUL << shift;
+			u64 width = regs[i]->fields[f].width ?: 4;
+			u64 mask = GENMASK_ULL(shift + width - 1, shift);
 			u64 v;
 
 			if (find_field(cmdline, regs[i], f, &v))
@@ -140,7 +213,7 @@ static void __init match_options(const char *cmdline)
 
 			/*
 			 * If an override gets filtered out, advertise
-			 * it by setting the value to 0xf, but
+			 * it by setting the value to the all-ones while
 			 * clearing the mask... Yes, this is fragile.
 			 */
 			if (regs[i]->fields[f].filter &&
@@ -222,9 +295,9 @@ static __init void parse_cmdline(void)
 }
 
 /* Keep checkers quiet */
-void init_feature_override(void);
+void init_feature_override(u64 boot_status);
 
-asmlinkage void __init init_feature_override(void)
+asmlinkage void __init init_feature_override(u64 boot_status)
 {
 	int i;
 
@@ -235,6 +308,8 @@ asmlinkage void __init init_feature_override(void)
 		}
 	}
 
+	__boot_status = boot_status;
+
 	parse_cmdline();
 
 	for (i = 0; i < ARRAY_SIZE(regs); i++) {
diff --git a/arch/arm64/kernel/image-vars.h b/arch/arm64/kernel/image-vars.h
index c96a9a0043bf..8151412653de 100644
--- a/arch/arm64/kernel/image-vars.h
+++ b/arch/arm64/kernel/image-vars.h
@@ -10,11 +10,8 @@
 #error This file should only be included in vmlinux.lds.S
 #endif
 
-#ifdef CONFIG_EFI
-
-__efistub_kernel_size		= _edata - _text;
-__efistub_primary_entry_offset	= primary_entry - _text;
-
+PROVIDE(__efistub_kernel_size		= _edata - _text);
+PROVIDE(__efistub_primary_entry_offset	= primary_entry - _text);
 
 /*
  * The EFI stub has its own symbol namespace prefixed by __efistub_, to
@@ -25,31 +22,24 @@ __efistub_primary_entry_offset	= primary_entry - _text;
  * linked at. The routines below are all implemented in assembler in a
  * position independent manner
  */
-__efistub_memcmp		= __pi_memcmp;
-__efistub_memchr		= __pi_memchr;
-__efistub_memcpy		= __pi_memcpy;
-__efistub_memmove		= __pi_memmove;
-__efistub_memset		= __pi_memset;
-__efistub_strlen		= __pi_strlen;
-__efistub_strnlen		= __pi_strnlen;
-__efistub_strcmp		= __pi_strcmp;
-__efistub_strncmp		= __pi_strncmp;
-__efistub_strrchr		= __pi_strrchr;
-__efistub_dcache_clean_poc = __pi_dcache_clean_poc;
-
-#if defined(CONFIG_KASAN_GENERIC) || defined(CONFIG_KASAN_SW_TAGS)
-__efistub___memcpy		= __pi_memcpy;
-__efistub___memmove		= __pi_memmove;
-__efistub___memset		= __pi_memset;
-#endif
-
-__efistub__text			= _text;
-__efistub__end			= _end;
-__efistub__edata		= _edata;
-__efistub_screen_info		= screen_info;
-__efistub__ctype		= _ctype;
-
-#endif
+PROVIDE(__efistub_memcmp		= __pi_memcmp);
+PROVIDE(__efistub_memchr		= __pi_memchr);
+PROVIDE(__efistub_strlen		= __pi_strlen);
+PROVIDE(__efistub_strnlen		= __pi_strnlen);
+PROVIDE(__efistub_strcmp		= __pi_strcmp);
+PROVIDE(__efistub_strncmp		= __pi_strncmp);
+PROVIDE(__efistub_strrchr		= __pi_strrchr);
+PROVIDE(__efistub_dcache_clean_poc	= __pi_dcache_clean_poc);
+
+PROVIDE(__efistub__text			= _text);
+PROVIDE(__efistub__end			= _end);
+PROVIDE(__efistub__edata		= _edata);
+PROVIDE(__efistub_screen_info		= screen_info);
+PROVIDE(__efistub__ctype		= _ctype);
+
+PROVIDE(__pi___memcpy			= __pi_memcpy);
+PROVIDE(__pi___memmove			= __pi_memmove);
+PROVIDE(__pi___memset			= __pi_memset);
 
 #ifdef CONFIG_KVM
 
@@ -66,6 +56,11 @@ KVM_NVHE_ALIAS(kvm_patch_vector_branch);
 KVM_NVHE_ALIAS(kvm_update_va_mask);
 KVM_NVHE_ALIAS(kvm_get_kimage_voffset);
 KVM_NVHE_ALIAS(kvm_compute_final_ctr_el0);
+KVM_NVHE_ALIAS(spectre_bhb_patch_loop_iter);
+KVM_NVHE_ALIAS(spectre_bhb_patch_loop_mitigation_enable);
+KVM_NVHE_ALIAS(spectre_bhb_patch_wa3);
+KVM_NVHE_ALIAS(spectre_bhb_patch_clearbhb);
+KVM_NVHE_ALIAS(alt_cb_patch_nops);
 
 /* Global kernel state accessed by nVHE hyp code. */
 KVM_NVHE_ALIAS(kvm_vgic_global_state);
@@ -79,9 +74,8 @@ KVM_NVHE_ALIAS(__hyp_stub_vectors);
 /* Kernel symbol used by icache_is_vpipt(). */
 KVM_NVHE_ALIAS(__icache_flags);
 
-/* Kernel symbols needed for cpus_have_final/const_caps checks. */
-KVM_NVHE_ALIAS(arm64_const_caps_ready);
-KVM_NVHE_ALIAS(cpu_hwcap_keys);
+/* VMID bits set by the KVM VMID allocator */
+KVM_NVHE_ALIAS(kvm_arm_vmid_bits);
 
 /* Static keys which are set if a vGIC trap should be handled in hyp. */
 KVM_NVHE_ALIAS(vgic_v2_cpuif_trap);
@@ -102,7 +96,9 @@ KVM_NVHE_ALIAS(__stop___kvm_ex_table);
 KVM_NVHE_ALIAS(kvm_arm_hyp_percpu_base);
 
 /* PMU available static key */
+#ifdef CONFIG_HW_PERF_EVENTS
 KVM_NVHE_ALIAS(kvm_arm_pmu_available);
+#endif
 
 /* Position-independent library routines */
 KVM_NVHE_ALIAS_HYP(clear_page, __pi_clear_page);
diff --git a/arch/arm64/kernel/irq.c b/arch/arm64/kernel/irq.c
index bda49430c9ea..38dbd3828f13 100644
--- a/arch/arm64/kernel/irq.c
+++ b/arch/arm64/kernel/irq.c
@@ -21,7 +21,9 @@
 #include <linux/seq_file.h>
 #include <linux/vmalloc.h>
 #include <asm/daifflags.h>
+#include <asm/exception.h>
 #include <asm/vmap_stack.h>
+#include <asm/softirq_stack.h>
 
 /* Only access this in an NMI enter/exit */
 DEFINE_PER_CPU(struct nmi_ctx, nmi_contexts);
@@ -71,6 +73,18 @@ static void init_irq_stacks(void)
 }
 #endif
 
+#ifndef CONFIG_PREEMPT_RT
+static void ____do_softirq(struct pt_regs *regs)
+{
+	__do_softirq();
+}
+
+void do_softirq_own_stack(void)
+{
+	call_on_irq_stack(NULL, ____do_softirq);
+}
+#endif
+
 static void default_handle_irq(struct pt_regs *regs)
 {
 	panic("IRQ taken without a root IRQ handler\n");
diff --git a/arch/arm64/kernel/jump_label.c b/arch/arm64/kernel/jump_label.c
index fc98037e1220..faf88ec9c48e 100644
--- a/arch/arm64/kernel/jump_label.c
+++ b/arch/arm64/kernel/jump_label.c
@@ -26,14 +26,3 @@ void arch_jump_label_transform(struct jump_entry *entry,
 
 	aarch64_insn_patch_text_nosync(addr, insn);
 }
-
-void arch_jump_label_transform_static(struct jump_entry *entry,
-				      enum jump_label_type type)
-{
-	/*
-	 * We use the architected A64 NOP in arch_static_branch, so there's no
-	 * need to patch an identical A64 NOP over the top of it here. The core
-	 * will call arch_jump_label_transform from a module notifier if the
-	 * NOP needs to be replaced by a branch.
-	 */
-}
diff --git a/arch/arm64/kernel/kaslr.c b/arch/arm64/kernel/kaslr.c
index 418b2bba1521..325455d16dbc 100644
--- a/arch/arm64/kernel/kaslr.c
+++ b/arch/arm64/kernel/kaslr.c
@@ -13,7 +13,6 @@
 #include <linux/pgtable.h>
 #include <linux/random.h>
 
-#include <asm/cacheflush.h>
 #include <asm/fixmap.h>
 #include <asm/kernel-pgtable.h>
 #include <asm/memory.h>
@@ -21,128 +20,45 @@
 #include <asm/sections.h>
 #include <asm/setup.h>
 
-enum kaslr_status {
-	KASLR_ENABLED,
-	KASLR_DISABLED_CMDLINE,
-	KASLR_DISABLED_NO_SEED,
-	KASLR_DISABLED_FDT_REMAP,
-};
-
-static enum kaslr_status __initdata kaslr_status;
 u64 __ro_after_init module_alloc_base;
 u16 __initdata memstart_offset_seed;
 
-static __init u64 get_kaslr_seed(void *fdt)
-{
-	int node, len;
-	fdt64_t *prop;
-	u64 ret;
-
-	node = fdt_path_offset(fdt, "/chosen");
-	if (node < 0)
-		return 0;
-
-	prop = fdt_getprop_w(fdt, node, "kaslr-seed", &len);
-	if (!prop || len != sizeof(u64))
-		return 0;
-
-	ret = fdt64_to_cpu(*prop);
-	*prop = 0;
-	return ret;
-}
-
 struct arm64_ftr_override kaslr_feature_override __initdata;
 
-/*
- * This routine will be executed with the kernel mapped at its default virtual
- * address, and if it returns successfully, the kernel will be remapped, and
- * start_kernel() will be executed from a randomized virtual offset. The
- * relocation will result in all absolute references (e.g., static variables
- * containing function pointers) to be reinitialized, and zero-initialized
- * .bss variables will be reset to 0.
- */
-u64 __init kaslr_early_init(void)
+static int __init kaslr_init(void)
 {
-	void *fdt;
-	u64 seed, offset, mask, module_range;
-	unsigned long raw;
+	u64 module_range;
+	u32 seed;
 
 	/*
 	 * Set a reasonable default for module_alloc_base in case
 	 * we end up running with module randomization disabled.
 	 */
 	module_alloc_base = (u64)_etext - MODULES_VSIZE;
-	dcache_clean_inval_poc((unsigned long)&module_alloc_base,
-			    (unsigned long)&module_alloc_base +
-				    sizeof(module_alloc_base));
-
-	/*
-	 * Try to map the FDT early. If this fails, we simply bail,
-	 * and proceed with KASLR disabled. We will make another
-	 * attempt at mapping the FDT in setup_machine()
-	 */
-	fdt = get_early_fdt_ptr();
-	if (!fdt) {
-		kaslr_status = KASLR_DISABLED_FDT_REMAP;
-		return 0;
-	}
 
-	/*
-	 * Retrieve (and wipe) the seed from the FDT
-	 */
-	seed = get_kaslr_seed(fdt);
-
-	/*
-	 * Check if 'nokaslr' appears on the command line, and
-	 * return 0 if that is the case.
-	 */
 	if (kaslr_feature_override.val & kaslr_feature_override.mask & 0xf) {
-		kaslr_status = KASLR_DISABLED_CMDLINE;
+		pr_info("KASLR disabled on command line\n");
 		return 0;
 	}
 
-	/*
-	 * Mix in any entropy obtainable architecturally if enabled
-	 * and supported.
-	 */
-
-	if (arch_get_random_seed_long_early(&raw))
-		seed ^= raw;
-
-	if (!seed) {
-		kaslr_status = KASLR_DISABLED_NO_SEED;
+	if (!kaslr_offset()) {
+		pr_warn("KASLR disabled due to lack of seed\n");
 		return 0;
 	}
 
+	pr_info("KASLR enabled\n");
+
 	/*
-	 * OK, so we are proceeding with KASLR enabled. Calculate a suitable
-	 * kernel image offset from the seed. Let's place the kernel in the
-	 * middle half of the VMALLOC area (VA_BITS_MIN - 2), and stay clear of
-	 * the lower and upper quarters to avoid colliding with other
-	 * allocations.
-	 * Even if we could randomize at page granularity for 16k and 64k pages,
-	 * let's always round to 2 MB so we don't interfere with the ability to
-	 * map using contiguous PTEs
+	 * KASAN without KASAN_VMALLOC does not expect the module region to
+	 * intersect the vmalloc region, since shadow memory is allocated for
+	 * each module at load time, whereas the vmalloc region will already be
+	 * shadowed by KASAN zero pages.
 	 */
-	mask = ((1UL << (VA_BITS_MIN - 2)) - 1) & ~(SZ_2M - 1);
-	offset = BIT(VA_BITS_MIN - 3) + (seed & mask);
+	BUILD_BUG_ON((IS_ENABLED(CONFIG_KASAN_GENERIC) ||
+	              IS_ENABLED(CONFIG_KASAN_SW_TAGS)) &&
+		     !IS_ENABLED(CONFIG_KASAN_VMALLOC));
 
-	/* use the top 16 bits to randomize the linear region */
-	memstart_offset_seed = seed >> 48;
-
-	if (!IS_ENABLED(CONFIG_KASAN_VMALLOC) &&
-	    (IS_ENABLED(CONFIG_KASAN_GENERIC) ||
-	     IS_ENABLED(CONFIG_KASAN_SW_TAGS)))
-		/*
-		 * KASAN without KASAN_VMALLOC does not expect the module region
-		 * to intersect the vmalloc region, since shadow memory is
-		 * allocated for each module at load time, whereas the vmalloc
-		 * region is shadowed by KASAN zero pages. So keep modules
-		 * out of the vmalloc region if KASAN is enabled without
-		 * KASAN_VMALLOC, and put the kernel well within 4 GB of the
-		 * module region.
-		 */
-		return offset % SZ_2G;
+	seed = get_random_u32();
 
 	if (IS_ENABLED(CONFIG_RANDOMIZE_MODULE_REGION_FULL)) {
 		/*
@@ -154,8 +70,7 @@ u64 __init kaslr_early_init(void)
 		 * resolved normally.)
 		 */
 		module_range = SZ_2G - (u64)(_end - _stext);
-		module_alloc_base = max((u64)_end + offset - SZ_2G,
-					(u64)MODULES_VADDR);
+		module_alloc_base = max((u64)_end - SZ_2G, (u64)MODULES_VADDR);
 	} else {
 		/*
 		 * Randomize the module region by setting module_alloc_base to
@@ -167,40 +82,12 @@ u64 __init kaslr_early_init(void)
 		 * when ARM64_MODULE_PLTS is enabled.
 		 */
 		module_range = MODULES_VSIZE - (u64)(_etext - _stext);
-		module_alloc_base = (u64)_etext + offset - MODULES_VSIZE;
 	}
 
 	/* use the lower 21 bits to randomize the base of the module region */
 	module_alloc_base += (module_range * (seed & ((1 << 21) - 1))) >> 21;
 	module_alloc_base &= PAGE_MASK;
 
-	dcache_clean_inval_poc((unsigned long)&module_alloc_base,
-			    (unsigned long)&module_alloc_base +
-				    sizeof(module_alloc_base));
-	dcache_clean_inval_poc((unsigned long)&memstart_offset_seed,
-			    (unsigned long)&memstart_offset_seed +
-				    sizeof(memstart_offset_seed));
-
-	return offset;
-}
-
-static int __init kaslr_init(void)
-{
-	switch (kaslr_status) {
-	case KASLR_ENABLED:
-		pr_info("KASLR enabled\n");
-		break;
-	case KASLR_DISABLED_CMDLINE:
-		pr_info("KASLR disabled on command line\n");
-		break;
-	case KASLR_DISABLED_NO_SEED:
-		pr_warn("KASLR disabled due to lack of seed\n");
-		break;
-	case KASLR_DISABLED_FDT_REMAP:
-		pr_warn("KASLR disabled due to FDT remapping failure\n");
-		break;
-	}
-
 	return 0;
 }
-core_initcall(kaslr_init)
+subsys_initcall(kaslr_init)
diff --git a/arch/arm64/kernel/kexec_image.c b/arch/arm64/kernel/kexec_image.c
index 9ec34690e255..5ed6a585f21f 100644
--- a/arch/arm64/kernel/kexec_image.c
+++ b/arch/arm64/kernel/kexec_image.c
@@ -14,7 +14,6 @@
 #include <linux/kexec.h>
 #include <linux/pe.h>
 #include <linux/string.h>
-#include <linux/verification.h>
 #include <asm/byteorder.h>
 #include <asm/cpufeature.h>
 #include <asm/image.h>
@@ -130,18 +129,10 @@ static void *image_load(struct kimage *image,
 	return NULL;
 }
 
-#ifdef CONFIG_KEXEC_IMAGE_VERIFY_SIG
-static int image_verify_sig(const char *kernel, unsigned long kernel_len)
-{
-	return verify_pefile_signature(kernel, kernel_len, NULL,
-				       VERIFYING_KEXEC_PE_SIGNATURE);
-}
-#endif
-
 const struct kexec_file_ops kexec_image_ops = {
 	.probe = image_probe,
 	.load = image_load,
 #ifdef CONFIG_KEXEC_IMAGE_VERIFY_SIG
-	.verify_sig = image_verify_sig,
+	.verify_sig = kexec_kernel_verify_pe_sig,
 #endif
 };
diff --git a/arch/arm64/kernel/kgdb.c b/arch/arm64/kernel/kgdb.c
index 2aede780fb80..cda9c1e9864f 100644
--- a/arch/arm64/kernel/kgdb.c
+++ b/arch/arm64/kernel/kgdb.c
@@ -232,14 +232,14 @@ int kgdb_arch_handle_exception(int exception_vector, int signo,
 	return err;
 }
 
-static int kgdb_brk_fn(struct pt_regs *regs, unsigned int esr)
+static int kgdb_brk_fn(struct pt_regs *regs, unsigned long esr)
 {
 	kgdb_handle_exception(1, SIGTRAP, 0, regs);
 	return DBG_HOOK_HANDLED;
 }
 NOKPROBE_SYMBOL(kgdb_brk_fn)
 
-static int kgdb_compiled_brk_fn(struct pt_regs *regs, unsigned int esr)
+static int kgdb_compiled_brk_fn(struct pt_regs *regs, unsigned long esr)
 {
 	compiled_break = 1;
 	kgdb_handle_exception(1, SIGTRAP, 0, regs);
@@ -248,7 +248,7 @@ static int kgdb_compiled_brk_fn(struct pt_regs *regs, unsigned int esr)
 }
 NOKPROBE_SYMBOL(kgdb_compiled_brk_fn);
 
-static int kgdb_step_brk_fn(struct pt_regs *regs, unsigned int esr)
+static int kgdb_step_brk_fn(struct pt_regs *regs, unsigned long esr)
 {
 	if (!kgdb_single_step)
 		return DBG_HOOK_ERROR;
diff --git a/arch/arm64/kernel/kuser32.S b/arch/arm64/kernel/kuser32.S
index 42bd8c0c60e0..692e9d2e31e5 100644
--- a/arch/arm64/kernel/kuser32.S
+++ b/arch/arm64/kernel/kuser32.S
@@ -15,6 +15,7 @@
 
 #include <asm/unistd.h>
 
+	.section .rodata
 	.align	5
 	.globl	__kuser_helper_start
 __kuser_helper_start:
diff --git a/arch/arm64/kernel/machine_kexec.c b/arch/arm64/kernel/machine_kexec.c
index 6fb31c117ebe..ce3d40120f72 100644
--- a/arch/arm64/kernel/machine_kexec.c
+++ b/arch/arm64/kernel/machine_kexec.c
@@ -104,13 +104,15 @@ static void *kexec_page_alloc(void *arg)
 {
 	struct kimage *kimage = (struct kimage *)arg;
 	struct page *page = kimage_alloc_control_pages(kimage, 0);
+	void *vaddr = NULL;
 
 	if (!page)
 		return NULL;
 
-	memset(page_address(page), 0, PAGE_SIZE);
+	vaddr = page_address(page);
+	memset(vaddr, 0, PAGE_SIZE);
 
-	return page_address(page);
+	return vaddr;
 }
 
 int machine_kexec_post_load(struct kimage *kimage)
@@ -202,7 +204,7 @@ void machine_kexec(struct kimage *kimage)
 		typeof(cpu_soft_restart) *restart;
 
 		cpu_install_idmap();
-		restart = (void *)__pa_symbol(function_nocfi(cpu_soft_restart));
+		restart = (void *)__pa_symbol(cpu_soft_restart);
 		restart(is_hyp_nvhe(), kimage->start, kimage->arch.dtb_mem,
 			0, 0);
 	} else {
@@ -327,8 +329,13 @@ bool crash_is_nosave(unsigned long pfn)
 
 	/* in reserved memory? */
 	addr = __pfn_to_phys(pfn);
-	if ((addr < crashk_res.start) || (crashk_res.end < addr))
-		return false;
+	if ((addr < crashk_res.start) || (crashk_res.end < addr)) {
+		if (!crashk_low_res.end)
+			return false;
+
+		if ((addr < crashk_low_res.start) || (crashk_low_res.end < addr))
+			return false;
+	}
 
 	if (!kexec_crash_image)
 		return true;
diff --git a/arch/arm64/kernel/machine_kexec_file.c b/arch/arm64/kernel/machine_kexec_file.c
index 63634b4d72c1..a11a6e14ba89 100644
--- a/arch/arm64/kernel/machine_kexec_file.c
+++ b/arch/arm64/kernel/machine_kexec_file.c
@@ -47,7 +47,7 @@ static int prepare_elf_headers(void **addr, unsigned long *sz)
 	u64 i;
 	phys_addr_t start, end;
 
-	nr_ranges = 1; /* for exclusion of crashkernel region */
+	nr_ranges = 2; /* for exclusion of crashkernel region */
 	for_each_mem_range(i, &start, &end)
 		nr_ranges++;
 
@@ -65,10 +65,18 @@ static int prepare_elf_headers(void **addr, unsigned long *sz)
 
 	/* Exclude crashkernel region */
 	ret = crash_exclude_mem_range(cmem, crashk_res.start, crashk_res.end);
+	if (ret)
+		goto out;
+
+	if (crashk_low_res.end) {
+		ret = crash_exclude_mem_range(cmem, crashk_low_res.start, crashk_low_res.end);
+		if (ret)
+			goto out;
+	}
 
-	if (!ret)
-		ret =  crash_prepare_elf64_headers(cmem, true, addr, sz);
+	ret = crash_prepare_elf64_headers(cmem, true, addr, sz);
 
+out:
 	kfree(cmem);
 	return ret;
 }
@@ -149,6 +157,7 @@ int load_other_segments(struct kimage *image,
 					   initrd_len, cmdline, 0);
 	if (!dtb) {
 		pr_err("Preparing for new dtb failed\n");
+		ret = -EINVAL;
 		goto out_err;
 	}
 
diff --git a/arch/arm64/kernel/module-plts.c b/arch/arm64/kernel/module-plts.c
index e53493d8b208..5a0a8f552a61 100644
--- a/arch/arm64/kernel/module-plts.c
+++ b/arch/arm64/kernel/module-plts.c
@@ -37,7 +37,8 @@ struct plt_entry get_plt_entry(u64 dst, void *pc)
 	return plt;
 }
 
-bool plt_entries_equal(const struct plt_entry *a, const struct plt_entry *b)
+static bool plt_entries_equal(const struct plt_entry *a,
+			      const struct plt_entry *b)
 {
 	u64 p, q;
 
@@ -220,7 +221,7 @@ static unsigned int count_plts(Elf64_Sym *syms, Elf64_Rela *rela, int num,
 			 * increasing the section's alignment so that the
 			 * resulting address of this instruction is guaranteed
 			 * to equal the offset in that particular bit (as well
-			 * as all less signficant bits). This ensures that the
+			 * as all less significant bits). This ensures that the
 			 * address modulo 4 KB != 0xfff8 or 0xfffc (which would
 			 * have all ones in bits [11:3])
 			 */
diff --git a/arch/arm64/kernel/module.c b/arch/arm64/kernel/module.c
index b5ec010c481f..76b41e4ca9fa 100644
--- a/arch/arm64/kernel/module.c
+++ b/arch/arm64/kernel/module.c
@@ -36,7 +36,7 @@ void *module_alloc(unsigned long size)
 		module_alloc_end = MODULES_END;
 
 	p = __vmalloc_node_range(size, MODULE_ALIGN, module_alloc_base,
-				module_alloc_end, gfp_mask, PAGE_KERNEL, 0,
+				module_alloc_end, gfp_mask, PAGE_KERNEL, VM_DEFER_KMEMLEAK,
 				NUMA_NO_NODE, __builtin_return_address(0));
 
 	if (!p && IS_ENABLED(CONFIG_ARM64_MODULE_PLTS) &&
@@ -58,12 +58,13 @@ void *module_alloc(unsigned long size)
 				PAGE_KERNEL, 0, NUMA_NO_NODE,
 				__builtin_return_address(0));
 
-	if (p && (kasan_module_alloc(p, size) < 0)) {
+	if (p && (kasan_alloc_module_shadow(p, size, gfp_mask) < 0)) {
 		vfree(p);
 		return NULL;
 	}
 
-	return p;
+	/* Memory is intended to be executable, reset the pointer tag. */
+	return kasan_reset_tag(p);
 }
 
 enum aarch64_reloc_op {
@@ -475,21 +476,6 @@ overflow:
 	return -ENOEXEC;
 }
 
-static const Elf_Shdr *find_section(const Elf_Ehdr *hdr,
-				    const Elf_Shdr *sechdrs,
-				    const char *name)
-{
-	const Elf_Shdr *s, *se;
-	const char *secstrs = (void *)hdr + sechdrs[hdr->e_shstrndx].sh_offset;
-
-	for (s = sechdrs, se = sechdrs + hdr->e_shnum; s < se; s++) {
-		if (strcmp(name, secstrs + s->sh_name) == 0)
-			return s;
-	}
-
-	return NULL;
-}
-
 static inline void __init_plt(struct plt_entry *plt, unsigned long addr)
 {
 	*plt = get_plt_entry(addr, plt);
diff --git a/arch/arm64/kernel/mte.c b/arch/arm64/kernel/mte.c
index f418ebc65f95..7467217c1eaf 100644
--- a/arch/arm64/kernel/mte.c
+++ b/arch/arm64/kernel/mte.c
@@ -15,6 +15,7 @@
 #include <linux/swapops.h>
 #include <linux/thread_info.h>
 #include <linux/types.h>
+#include <linux/uaccess.h>
 #include <linux/uio.h>
 
 #include <asm/barrier.h>
@@ -47,16 +48,12 @@ static void mte_sync_page_tags(struct page *page, pte_t old_pte,
 	if (!pte_is_tagged)
 		return;
 
-	page_kasan_tag_reset(page);
 	/*
-	 * We need smp_wmb() in between setting the flags and clearing the
-	 * tags because if another thread reads page->flags and builds a
-	 * tagged address out of it, there is an actual dependency to the
-	 * memory access, but on the current thread we do not guarantee that
-	 * the new page->flags are visible before the tags were updated.
+	 * Test PG_mte_tagged again in case it was racing with another
+	 * set_pte_at().
 	 */
-	smp_wmb();
-	mte_clear_page_tags(page_address(page));
+	if (!test_and_set_bit(PG_mte_tagged, &page->flags))
+		mte_clear_page_tags(page_address(page));
 }
 
 void mte_sync_tags(pte_t old_pte, pte_t pte)
@@ -72,10 +69,13 @@ void mte_sync_tags(pte_t old_pte, pte_t pte)
 
 	/* if PG_mte_tagged is set, tags have already been initialised */
 	for (i = 0; i < nr_pages; i++, page++) {
-		if (!test_and_set_bit(PG_mte_tagged, &page->flags))
+		if (!test_bit(PG_mte_tagged, &page->flags))
 			mte_sync_page_tags(page, old_pte, check_swap,
 					   pte_is_tagged);
 	}
+
+	/* ensure the tags are visible before the PTE is set */
+	smp_wmb();
 }
 
 int memcmp_pages(struct page *page1, struct page *page2)
@@ -106,7 +106,8 @@ int memcmp_pages(struct page *page1, struct page *page2)
 static inline void __mte_enable_kernel(const char *mode, unsigned long tcf)
 {
 	/* Enable MTE Sync Mode for EL1. */
-	sysreg_clear_set(sctlr_el1, SCTLR_ELx_TCF_MASK, tcf);
+	sysreg_clear_set(sctlr_el1, SCTLR_EL1_TCF_MASK,
+			 SYS_FIELD_PREP(SCTLR_EL1, TCF, tcf));
 	isb();
 
 	pr_info_once("MTE: enabled in %s mode at EL1\n", mode);
@@ -122,12 +123,12 @@ void mte_enable_kernel_sync(void)
 	WARN_ONCE(system_uses_mte_async_or_asymm_mode(),
 			"MTE async mode enabled system wide!");
 
-	__mte_enable_kernel("synchronous", SCTLR_ELx_TCF_SYNC);
+	__mte_enable_kernel("synchronous", SCTLR_EL1_TCF_SYNC);
 }
 
 void mte_enable_kernel_async(void)
 {
-	__mte_enable_kernel("asynchronous", SCTLR_ELx_TCF_ASYNC);
+	__mte_enable_kernel("asynchronous", SCTLR_EL1_TCF_ASYNC);
 
 	/*
 	 * MTE async mode is set system wide by the first PE that
@@ -144,7 +145,7 @@ void mte_enable_kernel_async(void)
 void mte_enable_kernel_asymm(void)
 {
 	if (cpus_have_cap(ARM64_MTE_ASYMM)) {
-		__mte_enable_kernel("asymmetric", SCTLR_ELx_TCF_ASYMM);
+		__mte_enable_kernel("asymmetric", SCTLR_EL1_TCF_ASYMM);
 
 		/*
 		 * MTE asymm mode behaves as async mode for store
@@ -186,6 +187,11 @@ void mte_check_tfsr_el1(void)
 }
 #endif
 
+/*
+ * This is where we actually resolve the system and process MTE mode
+ * configuration into an actual value in SCTLR_EL1 that affects
+ * userspace.
+ */
 static void mte_update_sctlr_user(struct task_struct *task)
 {
 	/*
@@ -199,12 +205,23 @@ static void mte_update_sctlr_user(struct task_struct *task)
 	unsigned long pref, resolved_mte_tcf;
 
 	pref = __this_cpu_read(mte_tcf_preferred);
+	/*
+	 * If there is no overlap between the system preferred and
+	 * program requested values go with what was requested.
+	 */
 	resolved_mte_tcf = (mte_ctrl & pref) ? pref : mte_ctrl;
 	sctlr &= ~SCTLR_EL1_TCF0_MASK;
-	if (resolved_mte_tcf & MTE_CTRL_TCF_ASYNC)
-		sctlr |= SCTLR_EL1_TCF0_ASYNC;
+	/*
+	 * Pick an actual setting. The order in which we check for
+	 * set bits and map into register values determines our
+	 * default order.
+	 */
+	if (resolved_mte_tcf & MTE_CTRL_TCF_ASYMM)
+		sctlr |= SYS_FIELD_PREP_ENUM(SCTLR_EL1, TCF0, ASYMM);
+	else if (resolved_mte_tcf & MTE_CTRL_TCF_ASYNC)
+		sctlr |= SYS_FIELD_PREP_ENUM(SCTLR_EL1, TCF0, ASYNC);
 	else if (resolved_mte_tcf & MTE_CTRL_TCF_SYNC)
-		sctlr |= SCTLR_EL1_TCF0_SYNC;
+		sctlr |= SYS_FIELD_PREP_ENUM(SCTLR_EL1, TCF0, SYNC);
 	task->thread.sctlr_user = sctlr;
 }
 
@@ -223,6 +240,11 @@ static void mte_update_gcr_excl(struct task_struct *task)
 		SYS_GCR_EL1);
 }
 
+#ifdef CONFIG_KASAN_HW_TAGS
+/* Only called from assembly, silence sparse */
+void __init kasan_hw_tags_enable(struct alt_instr *alt, __le32 *origptr,
+				 __le32 *updptr, int nr_inst);
+
 void __init kasan_hw_tags_enable(struct alt_instr *alt, __le32 *origptr,
 				 __le32 *updptr, int nr_inst)
 {
@@ -231,6 +253,7 @@ void __init kasan_hw_tags_enable(struct alt_instr *alt, __le32 *origptr,
 	if (kasan_hw_tags_enabled())
 		*updptr = cpu_to_le32(aarch64_insn_gen_nop());
 }
+#endif
 
 void mte_thread_init_user(void)
 {
@@ -253,6 +276,9 @@ void mte_thread_switch(struct task_struct *next)
 	mte_update_sctlr_user(next);
 	mte_update_gcr_excl(next);
 
+	/* TCO may not have been disabled on exception entry for the current task. */
+	mte_disable_tco_entry(next);
+
 	/*
 	 * Check if an async tag exception occurred at EL1.
 	 *
@@ -264,6 +290,49 @@ void mte_thread_switch(struct task_struct *next)
 	mte_check_tfsr_el1();
 }
 
+void mte_cpu_setup(void)
+{
+	u64 rgsr;
+
+	/*
+	 * CnP must be enabled only after the MAIR_EL1 register has been set
+	 * up. Inconsistent MAIR_EL1 between CPUs sharing the same TLB may
+	 * lead to the wrong memory type being used for a brief window during
+	 * CPU power-up.
+	 *
+	 * CnP is not a boot feature so MTE gets enabled before CnP, but let's
+	 * make sure that is the case.
+	 */
+	BUG_ON(read_sysreg(ttbr0_el1) & TTBR_CNP_BIT);
+	BUG_ON(read_sysreg(ttbr1_el1) & TTBR_CNP_BIT);
+
+	/* Normal Tagged memory type at the corresponding MAIR index */
+	sysreg_clear_set(mair_el1,
+			 MAIR_ATTRIDX(MAIR_ATTR_MASK, MT_NORMAL_TAGGED),
+			 MAIR_ATTRIDX(MAIR_ATTR_NORMAL_TAGGED,
+				      MT_NORMAL_TAGGED));
+
+	write_sysreg_s(KERNEL_GCR_EL1, SYS_GCR_EL1);
+
+	/*
+	 * If GCR_EL1.RRND=1 is implemented the same way as RRND=0, then
+	 * RGSR_EL1.SEED must be non-zero for IRG to produce
+	 * pseudorandom numbers. As RGSR_EL1 is UNKNOWN out of reset, we
+	 * must initialize it.
+	 */
+	rgsr = (read_sysreg(CNTVCT_EL0) & SYS_RGSR_EL1_SEED_MASK) <<
+	       SYS_RGSR_EL1_SEED_SHIFT;
+	if (rgsr == 0)
+		rgsr = 1 << SYS_RGSR_EL1_SEED_SHIFT;
+	write_sysreg_s(rgsr, SYS_RGSR_EL1);
+
+	/* clear any pending tag check faults in TFSR*_EL1 */
+	write_sysreg_s(0, SYS_TFSR_EL1);
+	write_sysreg_s(0, SYS_TFSRE0_EL1);
+
+	local_flush_tlb_all();
+}
+
 void mte_suspend_enter(void)
 {
 	if (!system_supports_mte())
@@ -280,6 +349,14 @@ void mte_suspend_enter(void)
 	mte_check_tfsr_el1();
 }
 
+void mte_suspend_exit(void)
+{
+	if (!system_supports_mte())
+		return;
+
+	mte_cpu_setup();
+}
+
 long set_mte_ctrl(struct task_struct *task, unsigned long arg)
 {
 	u64 mte_ctrl = (~((arg & PR_MTE_TAG_MASK) >> PR_MTE_TAG_SHIFT) &
@@ -293,6 +370,17 @@ long set_mte_ctrl(struct task_struct *task, unsigned long arg)
 	if (arg & PR_MTE_TCF_SYNC)
 		mte_ctrl |= MTE_CTRL_TCF_SYNC;
 
+	/*
+	 * If the system supports it and both sync and async modes are
+	 * specified then implicitly enable asymmetric mode.
+	 * Userspace could see a mix of both sync and async anyway due
+	 * to differing or changing defaults on CPUs.
+	 */
+	if (cpus_have_cap(ARM64_MTE_ASYMM) &&
+	    (arg & PR_MTE_TCF_ASYNC) &&
+	    (arg & PR_MTE_TCF_SYNC))
+		mte_ctrl |= MTE_CTRL_TCF_ASYMM;
+
 	task->thread.mte_ctrl = mte_ctrl;
 	if (task == current) {
 		preempt_disable();
@@ -467,6 +555,8 @@ static ssize_t mte_tcf_preferred_show(struct device *dev,
 		return sysfs_emit(buf, "async\n");
 	case MTE_CTRL_TCF_SYNC:
 		return sysfs_emit(buf, "sync\n");
+	case MTE_CTRL_TCF_ASYMM:
+		return sysfs_emit(buf, "asymm\n");
 	default:
 		return sysfs_emit(buf, "???\n");
 	}
@@ -482,6 +572,8 @@ static ssize_t mte_tcf_preferred_store(struct device *dev,
 		tcf = MTE_CTRL_TCF_ASYNC;
 	else if (sysfs_streq(buf, "sync"))
 		tcf = MTE_CTRL_TCF_SYNC;
+	else if (cpus_have_cap(ARM64_MTE_ASYMM) && sysfs_streq(buf, "asymm"))
+		tcf = MTE_CTRL_TCF_ASYMM;
 	else
 		return -EINVAL;
 
@@ -509,3 +601,32 @@ static int register_mte_tcf_preferred_sysctl(void)
 	return 0;
 }
 subsys_initcall(register_mte_tcf_preferred_sysctl);
+
+/*
+ * Return 0 on success, the number of bytes not probed otherwise.
+ */
+size_t mte_probe_user_range(const char __user *uaddr, size_t size)
+{
+	const char __user *end = uaddr + size;
+	int err = 0;
+	char val;
+
+	__raw_get_user(val, uaddr, err);
+	if (err)
+		return size;
+
+	uaddr = PTR_ALIGN(uaddr, MTE_GRANULE_SIZE);
+	while (uaddr < end) {
+		/*
+		 * A read is sufficient for mte, the caller should have probed
+		 * for the pte write permission if required.
+		 */
+		__raw_get_user(val, uaddr, err);
+		if (err)
+			return end - uaddr;
+		uaddr += MTE_GRANULE_SIZE;
+	}
+	(void)val;
+
+	return 0;
+}
diff --git a/arch/arm64/kernel/paravirt.c b/arch/arm64/kernel/paravirt.c
index 75fed4460407..57c7c211f8c7 100644
--- a/arch/arm64/kernel/paravirt.c
+++ b/arch/arm64/kernel/paravirt.c
@@ -35,7 +35,7 @@ static u64 native_steal_clock(int cpu)
 DEFINE_STATIC_CALL(pv_steal_clock, native_steal_clock);
 
 struct pv_time_stolen_time_region {
-	struct pvclock_vcpu_stolen_time *kaddr;
+	struct pvclock_vcpu_stolen_time __rcu *kaddr;
 };
 
 static DEFINE_PER_CPU(struct pv_time_stolen_time_region, stolen_time_region);
@@ -52,7 +52,9 @@ early_param("no-steal-acc", parse_no_stealacc);
 /* return stolen time in ns by asking the hypervisor */
 static u64 para_steal_clock(int cpu)
 {
+	struct pvclock_vcpu_stolen_time *kaddr = NULL;
 	struct pv_time_stolen_time_region *reg;
+	u64 ret = 0;
 
 	reg = per_cpu_ptr(&stolen_time_region, cpu);
 
@@ -61,28 +63,37 @@ static u64 para_steal_clock(int cpu)
 	 * online notification callback runs. Until the callback
 	 * has run we just return zero.
 	 */
-	if (!reg->kaddr)
+	rcu_read_lock();
+	kaddr = rcu_dereference(reg->kaddr);
+	if (!kaddr) {
+		rcu_read_unlock();
 		return 0;
+	}
 
-	return le64_to_cpu(READ_ONCE(reg->kaddr->stolen_time));
+	ret = le64_to_cpu(READ_ONCE(kaddr->stolen_time));
+	rcu_read_unlock();
+	return ret;
 }
 
 static int stolen_time_cpu_down_prepare(unsigned int cpu)
 {
+	struct pvclock_vcpu_stolen_time *kaddr = NULL;
 	struct pv_time_stolen_time_region *reg;
 
 	reg = this_cpu_ptr(&stolen_time_region);
 	if (!reg->kaddr)
 		return 0;
 
-	memunmap(reg->kaddr);
-	memset(reg, 0, sizeof(*reg));
+	kaddr = rcu_replace_pointer(reg->kaddr, NULL, true);
+	synchronize_rcu();
+	memunmap(kaddr);
 
 	return 0;
 }
 
 static int stolen_time_cpu_online(unsigned int cpu)
 {
+	struct pvclock_vcpu_stolen_time *kaddr = NULL;
 	struct pv_time_stolen_time_region *reg;
 	struct arm_smccc_res res;
 
@@ -93,17 +104,19 @@ static int stolen_time_cpu_online(unsigned int cpu)
 	if (res.a0 == SMCCC_RET_NOT_SUPPORTED)
 		return -EINVAL;
 
-	reg->kaddr = memremap(res.a0,
+	kaddr = memremap(res.a0,
 			      sizeof(struct pvclock_vcpu_stolen_time),
 			      MEMREMAP_WB);
 
+	rcu_assign_pointer(reg->kaddr, kaddr);
+
 	if (!reg->kaddr) {
 		pr_warn("Failed to map stolen time data structure\n");
 		return -ENOMEM;
 	}
 
-	if (le32_to_cpu(reg->kaddr->revision) != 0 ||
-	    le32_to_cpu(reg->kaddr->attributes) != 0) {
+	if (le32_to_cpu(kaddr->revision) != 0 ||
+	    le32_to_cpu(kaddr->attributes) != 0) {
 		pr_warn_once("Unexpected revision or attributes in stolen time data\n");
 		return -ENXIO;
 	}
diff --git a/arch/arm64/kernel/patching.c b/arch/arm64/kernel/patching.c
index 771f543464e0..33e0fabc0b79 100644
--- a/arch/arm64/kernel/patching.c
+++ b/arch/arm64/kernel/patching.c
@@ -117,8 +117,8 @@ static int __kprobes aarch64_insn_patch_text_cb(void *arg)
 	int i, ret = 0;
 	struct aarch64_insn_patch *pp = arg;
 
-	/* The first CPU becomes master */
-	if (atomic_inc_return(&pp->cpu_count) == 1) {
+	/* The last CPU becomes master */
+	if (atomic_inc_return(&pp->cpu_count) == num_online_cpus()) {
 		for (i = 0; ret == 0 && i < pp->insn_cnt; i++)
 			ret = aarch64_insn_patch_text_nosync(pp->text_addrs[i],
 							     pp->new_insns[i]);
diff --git a/arch/arm64/kernel/perf_callchain.c b/arch/arm64/kernel/perf_callchain.c
index 4a72c2727309..65b196e3ca6c 100644
--- a/arch/arm64/kernel/perf_callchain.c
+++ b/arch/arm64/kernel/perf_callchain.c
@@ -5,10 +5,10 @@
  * Copyright (C) 2015 ARM Limited
  */
 #include <linux/perf_event.h>
+#include <linux/stacktrace.h>
 #include <linux/uaccess.h>
 
 #include <asm/pointer_auth.h>
-#include <asm/stacktrace.h>
 
 struct frame_tail {
 	struct frame_tail	__user *fp;
@@ -102,7 +102,7 @@ compat_user_backtrace(struct compat_frame_tail __user *tail,
 void perf_callchain_user(struct perf_callchain_entry_ctx *entry,
 			 struct pt_regs *regs)
 {
-	if (perf_guest_cbs && perf_guest_cbs->is_in_guest()) {
+	if (perf_guest_state()) {
 		/* We don't support guest os callchain now */
 		return;
 	}
@@ -132,46 +132,38 @@ void perf_callchain_user(struct perf_callchain_entry_ctx *entry,
 	}
 }
 
-/*
- * Gets called by walk_stackframe() for every stackframe. This will be called
- * whist unwinding the stackframe and is like a subroutine return so we use
- * the PC.
- */
 static bool callchain_trace(void *data, unsigned long pc)
 {
 	struct perf_callchain_entry_ctx *entry = data;
-	perf_callchain_store(entry, pc);
-	return true;
+	return perf_callchain_store(entry, pc) == 0;
 }
 
 void perf_callchain_kernel(struct perf_callchain_entry_ctx *entry,
 			   struct pt_regs *regs)
 {
-	struct stackframe frame;
-
-	if (perf_guest_cbs && perf_guest_cbs->is_in_guest()) {
+	if (perf_guest_state()) {
 		/* We don't support guest os callchain now */
 		return;
 	}
 
-	start_backtrace(&frame, regs->regs[29], regs->pc);
-	walk_stackframe(current, &frame, callchain_trace, entry);
+	arch_stack_walk(callchain_trace, entry, current, regs);
 }
 
 unsigned long perf_instruction_pointer(struct pt_regs *regs)
 {
-	if (perf_guest_cbs && perf_guest_cbs->is_in_guest())
-		return perf_guest_cbs->get_guest_ip();
+	if (perf_guest_state())
+		return perf_guest_get_ip();
 
 	return instruction_pointer(regs);
 }
 
 unsigned long perf_misc_flags(struct pt_regs *regs)
 {
+	unsigned int guest_state = perf_guest_state();
 	int misc = 0;
 
-	if (perf_guest_cbs && perf_guest_cbs->is_in_guest()) {
-		if (perf_guest_cbs->is_user_mode())
+	if (guest_state) {
+		if (guest_state & PERF_GUEST_USER)
 			misc |= PERF_RECORD_MISC_GUEST_USER;
 		else
 			misc |= PERF_RECORD_MISC_GUEST_KERNEL;
diff --git a/arch/arm64/kernel/perf_event.c b/arch/arm64/kernel/perf_event.c
index b4044469527e..7b0643fe2f13 100644
--- a/arch/arm64/kernel/perf_event.c
+++ b/arch/arm64/kernel/perf_event.c
@@ -242,6 +242,16 @@ static struct attribute *armv8_pmuv3_event_attrs[] = {
 	ARMV8_EVENT_ATTR(l2d_cache_lmiss_rd, ARMV8_PMUV3_PERFCTR_L2D_CACHE_LMISS_RD),
 	ARMV8_EVENT_ATTR(l2i_cache_lmiss, ARMV8_PMUV3_PERFCTR_L2I_CACHE_LMISS),
 	ARMV8_EVENT_ATTR(l3d_cache_lmiss_rd, ARMV8_PMUV3_PERFCTR_L3D_CACHE_LMISS_RD),
+	ARMV8_EVENT_ATTR(trb_wrap, ARMV8_PMUV3_PERFCTR_TRB_WRAP),
+	ARMV8_EVENT_ATTR(trb_trig, ARMV8_PMUV3_PERFCTR_TRB_TRIG),
+	ARMV8_EVENT_ATTR(trcextout0, ARMV8_PMUV3_PERFCTR_TRCEXTOUT0),
+	ARMV8_EVENT_ATTR(trcextout1, ARMV8_PMUV3_PERFCTR_TRCEXTOUT1),
+	ARMV8_EVENT_ATTR(trcextout2, ARMV8_PMUV3_PERFCTR_TRCEXTOUT2),
+	ARMV8_EVENT_ATTR(trcextout3, ARMV8_PMUV3_PERFCTR_TRCEXTOUT3),
+	ARMV8_EVENT_ATTR(cti_trigout4, ARMV8_PMUV3_PERFCTR_CTI_TRIGOUT4),
+	ARMV8_EVENT_ATTR(cti_trigout5, ARMV8_PMUV3_PERFCTR_CTI_TRIGOUT5),
+	ARMV8_EVENT_ATTR(cti_trigout6, ARMV8_PMUV3_PERFCTR_CTI_TRIGOUT6),
+	ARMV8_EVENT_ATTR(cti_trigout7, ARMV8_PMUV3_PERFCTR_CTI_TRIGOUT7),
 	ARMV8_EVENT_ATTR(ldst_align_lat, ARMV8_PMUV3_PERFCTR_LDST_ALIGN_LAT),
 	ARMV8_EVENT_ATTR(ld_align_lat, ARMV8_PMUV3_PERFCTR_LD_ALIGN_LAT),
 	ARMV8_EVENT_ATTR(st_align_lat, ARMV8_PMUV3_PERFCTR_ST_ALIGN_LAT),
@@ -285,15 +295,24 @@ static const struct attribute_group armv8_pmuv3_events_attr_group = {
 
 PMU_FORMAT_ATTR(event, "config:0-15");
 PMU_FORMAT_ATTR(long, "config1:0");
+PMU_FORMAT_ATTR(rdpmc, "config1:1");
+
+static int sysctl_perf_user_access __read_mostly;
 
 static inline bool armv8pmu_event_is_64bit(struct perf_event *event)
 {
 	return event->attr.config1 & 0x1;
 }
 
+static inline bool armv8pmu_event_want_user_access(struct perf_event *event)
+{
+	return event->attr.config1 & 0x2;
+}
+
 static struct attribute *armv8_pmuv3_format_attrs[] = {
 	&format_attr_event.attr,
 	&format_attr_long.attr,
+	&format_attr_rdpmc.attr,
 	NULL,
 };
 
@@ -362,7 +381,7 @@ static const struct attribute_group armv8_pmuv3_caps_attr_group = {
  */
 #define	ARMV8_IDX_CYCLE_COUNTER	0
 #define	ARMV8_IDX_COUNTER0	1
-
+#define	ARMV8_IDX_CYCLE_COUNTER_USER	32
 
 /*
  * We unconditionally enable ARMv8.5-PMU long event counter support
@@ -371,21 +390,25 @@ static const struct attribute_group armv8_pmuv3_caps_attr_group = {
  */
 static bool armv8pmu_has_long_event(struct arm_pmu *cpu_pmu)
 {
-	return (cpu_pmu->pmuver >= ID_AA64DFR0_PMUVER_8_5);
+	return (cpu_pmu->pmuver >= ID_AA64DFR0_EL1_PMUVer_V3P5);
+}
+
+static inline bool armv8pmu_event_has_user_read(struct perf_event *event)
+{
+	return event->hw.flags & PERF_EVENT_FLAG_USER_READ_CNT;
 }
 
 /*
  * We must chain two programmable counters for 64 bit events,
  * except when we have allocated the 64bit cycle counter (for CPU
- * cycles event). This must be called only when the event has
- * a counter allocated.
+ * cycles event) or when user space counter access is enabled.
  */
 static inline bool armv8pmu_event_is_chained(struct perf_event *event)
 {
 	int idx = event->hw.idx;
 	struct arm_pmu *cpu_pmu = to_arm_pmu(event->pmu);
 
-	return !WARN_ON(idx < 0) &&
+	return !armv8pmu_event_has_user_read(event) &&
 	       armv8pmu_event_is_64bit(event) &&
 	       !armv8pmu_has_long_event(cpu_pmu) &&
 	       (idx != ARMV8_IDX_CYCLE_COUNTER);
@@ -718,6 +741,28 @@ static inline u32 armv8pmu_getreset_flags(void)
 	return value;
 }
 
+static void armv8pmu_disable_user_access(void)
+{
+	write_sysreg(0, pmuserenr_el0);
+}
+
+static void armv8pmu_enable_user_access(struct arm_pmu *cpu_pmu)
+{
+	int i;
+	struct pmu_hw_events *cpuc = this_cpu_ptr(cpu_pmu->hw_events);
+
+	/* Clear any unused counters to avoid leaking their contents */
+	for_each_clear_bit(i, cpuc->used_mask, cpu_pmu->num_events) {
+		if (i == ARMV8_IDX_CYCLE_COUNTER)
+			write_sysreg(0, pmccntr_el0);
+		else
+			armv8pmu_write_evcntr(i, 0);
+	}
+
+	write_sysreg(0, pmuserenr_el0);
+	write_sysreg(ARMV8_PMU_USERENR_ER | ARMV8_PMU_USERENR_CR, pmuserenr_el0);
+}
+
 static void armv8pmu_enable_event(struct perf_event *event)
 {
 	/*
@@ -761,6 +806,14 @@ static void armv8pmu_disable_event(struct perf_event *event)
 
 static void armv8pmu_start(struct arm_pmu *cpu_pmu)
 {
+	struct perf_event_context *task_ctx =
+		this_cpu_ptr(cpu_pmu->pmu.pmu_cpu_context)->task_ctx;
+
+	if (sysctl_perf_user_access && task_ctx && task_ctx->nr_user)
+		armv8pmu_enable_user_access(cpu_pmu);
+	else
+		armv8pmu_disable_user_access();
+
 	/* Enable all counters */
 	armv8pmu_pmcr_write(armv8pmu_pmcr_read() | ARMV8_PMU_PMCR_E);
 }
@@ -878,13 +931,16 @@ static int armv8pmu_get_event_idx(struct pmu_hw_events *cpuc,
 	if (evtype == ARMV8_PMUV3_PERFCTR_CPU_CYCLES) {
 		if (!test_and_set_bit(ARMV8_IDX_CYCLE_COUNTER, cpuc->used_mask))
 			return ARMV8_IDX_CYCLE_COUNTER;
+		else if (armv8pmu_event_is_64bit(event) &&
+			   armv8pmu_event_want_user_access(event) &&
+			   !armv8pmu_has_long_event(cpu_pmu))
+				return -EAGAIN;
 	}
 
 	/*
 	 * Otherwise use events counters
 	 */
-	if (armv8pmu_event_is_64bit(event) &&
-	    !armv8pmu_has_long_event(cpu_pmu))
+	if (armv8pmu_event_is_chained(event))
 		return	armv8pmu_get_chain_idx(cpuc, cpu_pmu);
 	else
 		return armv8pmu_get_single_idx(cpuc, cpu_pmu);
@@ -900,6 +956,22 @@ static void armv8pmu_clear_event_idx(struct pmu_hw_events *cpuc,
 		clear_bit(idx - 1, cpuc->used_mask);
 }
 
+static int armv8pmu_user_event_idx(struct perf_event *event)
+{
+	if (!sysctl_perf_user_access || !armv8pmu_event_has_user_read(event))
+		return 0;
+
+	/*
+	 * We remap the cycle counter index to 32 to
+	 * match the offset applied to the rest of
+	 * the counter indices.
+	 */
+	if (event->hw.idx == ARMV8_IDX_CYCLE_COUNTER)
+		return ARMV8_IDX_CYCLE_COUNTER_USER;
+
+	return event->hw.idx;
+}
+
 /*
  * Add an event filter to a given event.
  */
@@ -996,6 +1068,25 @@ static int __armv8_pmuv3_map_event(struct perf_event *event,
 	if (armv8pmu_event_is_64bit(event))
 		event->hw.flags |= ARMPMU_EVT_64BIT;
 
+	/*
+	 * User events must be allocated into a single counter, and so
+	 * must not be chained.
+	 *
+	 * Most 64-bit events require long counter support, but 64-bit
+	 * CPU_CYCLES events can be placed into the dedicated cycle
+	 * counter when this is free.
+	 */
+	if (armv8pmu_event_want_user_access(event)) {
+		if (!(event->attach_state & PERF_ATTACH_TASK))
+			return -EINVAL;
+		if (armv8pmu_event_is_64bit(event) &&
+		    (hw_event_id != ARMV8_PMUV3_PERFCTR_CPU_CYCLES) &&
+		    !armv8pmu_has_long_event(armpmu))
+			return -EOPNOTSUPP;
+
+		event->hw.flags |= PERF_EVENT_FLAG_USER_READ_CNT;
+	}
+
 	/* Only expose micro/arch events supported by this PMU */
 	if ((hw_event_id > 0) && (hw_event_id < ARMV8_PMUV3_MAX_COMMON_EVENTS)
 	    && test_bit(hw_event_id, armpmu->pmceid_bitmap)) {
@@ -1054,8 +1145,8 @@ static void __armv8pmu_probe_pmu(void *info)
 
 	dfr0 = read_sysreg(id_aa64dfr0_el1);
 	pmuver = cpuid_feature_extract_unsigned_field(dfr0,
-			ID_AA64DFR0_PMUVER_SHIFT);
-	if (pmuver == ID_AA64DFR0_PMUVER_IMP_DEF || pmuver == 0)
+			ID_AA64DFR0_EL1_PMUVer_SHIFT);
+	if (pmuver == ID_AA64DFR0_EL1_PMUVer_IMP_DEF || pmuver == 0)
 		return;
 
 	cpu_pmu->pmuver = pmuver;
@@ -1081,7 +1172,7 @@ static void __armv8pmu_probe_pmu(void *info)
 			     pmceid, ARMV8_PMUV3_MAX_COMMON_EVENTS);
 
 	/* store PMMIR_EL1 register for sysfs */
-	if (pmuver >= ID_AA64DFR0_PMUVER_8_4 && (pmceid_raw[1] & BIT(31)))
+	if (pmuver >= ID_AA64DFR0_EL1_PMUVer_V3P4 && (pmceid_raw[1] & BIT(31)))
 		cpu_pmu->reg_pmmir = read_cpuid(PMMIR_EL1);
 	else
 		cpu_pmu->reg_pmmir = 0;
@@ -1104,6 +1195,43 @@ static int armv8pmu_probe_pmu(struct arm_pmu *cpu_pmu)
 	return probe.present ? 0 : -ENODEV;
 }
 
+static void armv8pmu_disable_user_access_ipi(void *unused)
+{
+	armv8pmu_disable_user_access();
+}
+
+static int armv8pmu_proc_user_access_handler(struct ctl_table *table, int write,
+		void *buffer, size_t *lenp, loff_t *ppos)
+{
+	int ret = proc_dointvec_minmax(table, write, buffer, lenp, ppos);
+	if (ret || !write || sysctl_perf_user_access)
+		return ret;
+
+	on_each_cpu(armv8pmu_disable_user_access_ipi, NULL, 1);
+	return 0;
+}
+
+static struct ctl_table armv8_pmu_sysctl_table[] = {
+	{
+		.procname       = "perf_user_access",
+		.data		= &sysctl_perf_user_access,
+		.maxlen		= sizeof(unsigned int),
+		.mode           = 0644,
+		.proc_handler	= armv8pmu_proc_user_access_handler,
+		.extra1		= SYSCTL_ZERO,
+		.extra2		= SYSCTL_ONE,
+	},
+	{ }
+};
+
+static void armv8_pmu_register_sysctl_table(void)
+{
+	static u32 tbl_registered = 0;
+
+	if (!cmpxchg_relaxed(&tbl_registered, 0, 1))
+		register_sysctl("kernel", armv8_pmu_sysctl_table);
+}
+
 static int armv8_pmu_init(struct arm_pmu *cpu_pmu, char *name,
 			  int (*map_event)(struct perf_event *event),
 			  const struct attribute_group *events,
@@ -1127,6 +1255,8 @@ static int armv8_pmu_init(struct arm_pmu *cpu_pmu, char *name,
 	cpu_pmu->set_event_filter	= armv8pmu_set_event_filter;
 	cpu_pmu->filter_match		= armv8pmu_filter_match;
 
+	cpu_pmu->pmu.event_idx		= armv8pmu_user_event_idx;
+
 	cpu_pmu->name			= name;
 	cpu_pmu->map_event		= map_event;
 	cpu_pmu->attr_groups[ARMPMU_ATTR_GROUP_EVENTS] = events ?
@@ -1136,6 +1266,7 @@ static int armv8_pmu_init(struct arm_pmu *cpu_pmu, char *name,
 	cpu_pmu->attr_groups[ARMPMU_ATTR_GROUP_CAPS] = caps ?
 			caps : &armv8_pmuv3_caps_attr_group;
 
+	armv8_pmu_register_sysctl_table();
 	return 0;
 }
 
@@ -1145,17 +1276,32 @@ static int armv8_pmu_init_nogroups(struct arm_pmu *cpu_pmu, char *name,
 	return armv8_pmu_init(cpu_pmu, name, map_event, NULL, NULL, NULL);
 }
 
-static int armv8_pmuv3_init(struct arm_pmu *cpu_pmu)
-{
-	return armv8_pmu_init_nogroups(cpu_pmu, "armv8_pmuv3",
-				       armv8_pmuv3_map_event);
+#define PMUV3_INIT_SIMPLE(name)						\
+static int name##_pmu_init(struct arm_pmu *cpu_pmu)			\
+{									\
+	return armv8_pmu_init_nogroups(cpu_pmu, #name, armv8_pmuv3_map_event);\
 }
 
-static int armv8_a34_pmu_init(struct arm_pmu *cpu_pmu)
-{
-	return armv8_pmu_init_nogroups(cpu_pmu, "armv8_cortex_a34",
-				       armv8_pmuv3_map_event);
-}
+PMUV3_INIT_SIMPLE(armv8_pmuv3)
+
+PMUV3_INIT_SIMPLE(armv8_cortex_a34)
+PMUV3_INIT_SIMPLE(armv8_cortex_a55)
+PMUV3_INIT_SIMPLE(armv8_cortex_a65)
+PMUV3_INIT_SIMPLE(armv8_cortex_a75)
+PMUV3_INIT_SIMPLE(armv8_cortex_a76)
+PMUV3_INIT_SIMPLE(armv8_cortex_a77)
+PMUV3_INIT_SIMPLE(armv8_cortex_a78)
+PMUV3_INIT_SIMPLE(armv9_cortex_a510)
+PMUV3_INIT_SIMPLE(armv9_cortex_a710)
+PMUV3_INIT_SIMPLE(armv8_cortex_x1)
+PMUV3_INIT_SIMPLE(armv9_cortex_x2)
+PMUV3_INIT_SIMPLE(armv8_neoverse_e1)
+PMUV3_INIT_SIMPLE(armv8_neoverse_n1)
+PMUV3_INIT_SIMPLE(armv9_neoverse_n2)
+PMUV3_INIT_SIMPLE(armv8_neoverse_v1)
+
+PMUV3_INIT_SIMPLE(armv8_nvidia_carmel)
+PMUV3_INIT_SIMPLE(armv8_nvidia_denver)
 
 static int armv8_a35_pmu_init(struct arm_pmu *cpu_pmu)
 {
@@ -1169,24 +1315,12 @@ static int armv8_a53_pmu_init(struct arm_pmu *cpu_pmu)
 				       armv8_a53_map_event);
 }
 
-static int armv8_a55_pmu_init(struct arm_pmu *cpu_pmu)
-{
-	return armv8_pmu_init_nogroups(cpu_pmu, "armv8_cortex_a55",
-				       armv8_pmuv3_map_event);
-}
-
 static int armv8_a57_pmu_init(struct arm_pmu *cpu_pmu)
 {
 	return armv8_pmu_init_nogroups(cpu_pmu, "armv8_cortex_a57",
 				       armv8_a57_map_event);
 }
 
-static int armv8_a65_pmu_init(struct arm_pmu *cpu_pmu)
-{
-	return armv8_pmu_init_nogroups(cpu_pmu, "armv8_cortex_a65",
-				       armv8_pmuv3_map_event);
-}
-
 static int armv8_a72_pmu_init(struct arm_pmu *cpu_pmu)
 {
 	return armv8_pmu_init_nogroups(cpu_pmu, "armv8_cortex_a72",
@@ -1199,42 +1333,6 @@ static int armv8_a73_pmu_init(struct arm_pmu *cpu_pmu)
 				       armv8_a73_map_event);
 }
 
-static int armv8_a75_pmu_init(struct arm_pmu *cpu_pmu)
-{
-	return armv8_pmu_init_nogroups(cpu_pmu, "armv8_cortex_a75",
-				       armv8_pmuv3_map_event);
-}
-
-static int armv8_a76_pmu_init(struct arm_pmu *cpu_pmu)
-{
-	return armv8_pmu_init_nogroups(cpu_pmu, "armv8_cortex_a76",
-				       armv8_pmuv3_map_event);
-}
-
-static int armv8_a77_pmu_init(struct arm_pmu *cpu_pmu)
-{
-	return armv8_pmu_init_nogroups(cpu_pmu, "armv8_cortex_a77",
-				       armv8_pmuv3_map_event);
-}
-
-static int armv8_a78_pmu_init(struct arm_pmu *cpu_pmu)
-{
-	return armv8_pmu_init_nogroups(cpu_pmu, "armv8_cortex_a78",
-				       armv8_pmuv3_map_event);
-}
-
-static int armv8_e1_pmu_init(struct arm_pmu *cpu_pmu)
-{
-	return armv8_pmu_init_nogroups(cpu_pmu, "armv8_neoverse_e1",
-				       armv8_pmuv3_map_event);
-}
-
-static int armv8_n1_pmu_init(struct arm_pmu *cpu_pmu)
-{
-	return armv8_pmu_init_nogroups(cpu_pmu, "armv8_neoverse_n1",
-				       armv8_pmuv3_map_event);
-}
-
 static int armv8_thunder_pmu_init(struct arm_pmu *cpu_pmu)
 {
 	return armv8_pmu_init_nogroups(cpu_pmu, "armv8_cavium_thunder",
@@ -1248,23 +1346,31 @@ static int armv8_vulcan_pmu_init(struct arm_pmu *cpu_pmu)
 }
 
 static const struct of_device_id armv8_pmu_of_device_ids[] = {
-	{.compatible = "arm,armv8-pmuv3",	.data = armv8_pmuv3_init},
-	{.compatible = "arm,cortex-a34-pmu",	.data = armv8_a34_pmu_init},
+	{.compatible = "arm,armv8-pmuv3",	.data = armv8_pmuv3_pmu_init},
+	{.compatible = "arm,cortex-a34-pmu",	.data = armv8_cortex_a34_pmu_init},
 	{.compatible = "arm,cortex-a35-pmu",	.data = armv8_a35_pmu_init},
 	{.compatible = "arm,cortex-a53-pmu",	.data = armv8_a53_pmu_init},
-	{.compatible = "arm,cortex-a55-pmu",	.data = armv8_a55_pmu_init},
+	{.compatible = "arm,cortex-a55-pmu",	.data = armv8_cortex_a55_pmu_init},
 	{.compatible = "arm,cortex-a57-pmu",	.data = armv8_a57_pmu_init},
-	{.compatible = "arm,cortex-a65-pmu",	.data = armv8_a65_pmu_init},
+	{.compatible = "arm,cortex-a65-pmu",	.data = armv8_cortex_a65_pmu_init},
 	{.compatible = "arm,cortex-a72-pmu",	.data = armv8_a72_pmu_init},
 	{.compatible = "arm,cortex-a73-pmu",	.data = armv8_a73_pmu_init},
-	{.compatible = "arm,cortex-a75-pmu",	.data = armv8_a75_pmu_init},
-	{.compatible = "arm,cortex-a76-pmu",	.data = armv8_a76_pmu_init},
-	{.compatible = "arm,cortex-a77-pmu",	.data = armv8_a77_pmu_init},
-	{.compatible = "arm,cortex-a78-pmu",	.data = armv8_a78_pmu_init},
-	{.compatible = "arm,neoverse-e1-pmu",	.data = armv8_e1_pmu_init},
-	{.compatible = "arm,neoverse-n1-pmu",	.data = armv8_n1_pmu_init},
+	{.compatible = "arm,cortex-a75-pmu",	.data = armv8_cortex_a75_pmu_init},
+	{.compatible = "arm,cortex-a76-pmu",	.data = armv8_cortex_a76_pmu_init},
+	{.compatible = "arm,cortex-a77-pmu",	.data = armv8_cortex_a77_pmu_init},
+	{.compatible = "arm,cortex-a78-pmu",	.data = armv8_cortex_a78_pmu_init},
+	{.compatible = "arm,cortex-a510-pmu",	.data = armv9_cortex_a510_pmu_init},
+	{.compatible = "arm,cortex-a710-pmu",	.data = armv9_cortex_a710_pmu_init},
+	{.compatible = "arm,cortex-x1-pmu",	.data = armv8_cortex_x1_pmu_init},
+	{.compatible = "arm,cortex-x2-pmu",	.data = armv9_cortex_x2_pmu_init},
+	{.compatible = "arm,neoverse-e1-pmu",	.data = armv8_neoverse_e1_pmu_init},
+	{.compatible = "arm,neoverse-n1-pmu",	.data = armv8_neoverse_n1_pmu_init},
+	{.compatible = "arm,neoverse-n2-pmu",	.data = armv9_neoverse_n2_pmu_init},
+	{.compatible = "arm,neoverse-v1-pmu",	.data = armv8_neoverse_v1_pmu_init},
 	{.compatible = "cavium,thunder-pmu",	.data = armv8_thunder_pmu_init},
 	{.compatible = "brcm,vulcan-pmu",	.data = armv8_vulcan_pmu_init},
+	{.compatible = "nvidia,carmel-pmu",	.data = armv8_nvidia_carmel_pmu_init},
+	{.compatible = "nvidia,denver-pmu",	.data = armv8_nvidia_denver_pmu_init},
 	{},
 };
 
@@ -1287,7 +1393,7 @@ static int __init armv8_pmu_driver_init(void)
 	if (acpi_disabled)
 		return platform_driver_register(&armv8_pmu_driver);
 	else
-		return arm_pmu_acpi_probe(armv8_pmuv3_init);
+		return arm_pmu_acpi_probe(armv8_pmuv3_pmu_init);
 }
 device_initcall(armv8_pmu_driver_init)
 
@@ -1301,6 +1407,14 @@ void arch_perf_update_userpage(struct perf_event *event,
 	userpg->cap_user_time = 0;
 	userpg->cap_user_time_zero = 0;
 	userpg->cap_user_time_short = 0;
+	userpg->cap_user_rdpmc = armv8pmu_event_has_user_read(event);
+
+	if (userpg->cap_user_rdpmc) {
+		if (event->hw.flags & ARMPMU_EVT_64BIT)
+			userpg->pmc_width = 64;
+		else
+			userpg->pmc_width = 32;
+	}
 
 	do {
 		rd = sched_clock_read_begin(&seq);
diff --git a/arch/arm64/kernel/perf_regs.c b/arch/arm64/kernel/perf_regs.c
index f6f58e6265df..b4eece3eb17d 100644
--- a/arch/arm64/kernel/perf_regs.c
+++ b/arch/arm64/kernel/perf_regs.c
@@ -9,9 +9,27 @@
 #include <asm/perf_regs.h>
 #include <asm/ptrace.h>
 
+static u64 perf_ext_regs_value(int idx)
+{
+	switch (idx) {
+	case PERF_REG_ARM64_VG:
+		if (WARN_ON_ONCE(!system_supports_sve()))
+			return 0;
+
+		/*
+		 * Vector granule is current length in bits of SVE registers
+		 * divided by 64.
+		 */
+		return (task_get_sve_vl(current) * 8) / 64;
+	default:
+		WARN_ON_ONCE(true);
+		return 0;
+	}
+}
+
 u64 perf_reg_value(struct pt_regs *regs, int idx)
 {
-	if (WARN_ON_ONCE((u32)idx >= PERF_REG_ARM64_MAX))
+	if (WARN_ON_ONCE((u32)idx >= PERF_REG_ARM64_EXTENDED_MAX))
 		return 0;
 
 	/*
@@ -51,6 +69,9 @@ u64 perf_reg_value(struct pt_regs *regs, int idx)
 	if ((u32)idx == PERF_REG_ARM64_PC)
 		return regs->pc;
 
+	if ((u32)idx >= PERF_REG_ARM64_MAX)
+		return perf_ext_regs_value(idx);
+
 	return regs->regs[idx];
 }
 
@@ -58,7 +79,12 @@ u64 perf_reg_value(struct pt_regs *regs, int idx)
 
 int perf_reg_validate(u64 mask)
 {
-	if (!mask || mask & REG_RESERVED)
+	u64 reserved_mask = REG_RESERVED;
+
+	if (system_supports_sve())
+		reserved_mask &= ~(1ULL << PERF_REG_ARM64_VG);
+
+	if (!mask || mask & reserved_mask)
 		return -EINVAL;
 
 	return 0;
diff --git a/arch/arm64/kernel/pi/Makefile b/arch/arm64/kernel/pi/Makefile
new file mode 100644
index 000000000000..839291430cb3
--- /dev/null
+++ b/arch/arm64/kernel/pi/Makefile
@@ -0,0 +1,33 @@
+# SPDX-License-Identifier: GPL-2.0
+# Copyright 2022 Google LLC
+
+KBUILD_CFLAGS	:= $(subst $(CC_FLAGS_FTRACE),,$(KBUILD_CFLAGS)) -fpie \
+		   -Os -DDISABLE_BRANCH_PROFILING $(DISABLE_STACKLEAK_PLUGIN) \
+		   $(call cc-option,-mbranch-protection=none) \
+		   -I$(srctree)/scripts/dtc/libfdt -fno-stack-protector \
+		   -include $(srctree)/include/linux/hidden.h \
+		   -D__DISABLE_EXPORTS -ffreestanding -D__NO_FORTIFY \
+		   $(call cc-option,-fno-addrsig)
+
+# remove SCS flags from all objects in this directory
+KBUILD_CFLAGS	:= $(filter-out $(CC_FLAGS_SCS), $(KBUILD_CFLAGS))
+# disable LTO
+KBUILD_CFLAGS	:= $(filter-out $(CC_FLAGS_LTO), $(KBUILD_CFLAGS))
+
+GCOV_PROFILE	:= n
+KASAN_SANITIZE	:= n
+KCSAN_SANITIZE	:= n
+UBSAN_SANITIZE	:= n
+KCOV_INSTRUMENT	:= n
+
+$(obj)/%.pi.o: OBJCOPYFLAGS := --prefix-symbols=__pi_ \
+			       --remove-section=.note.gnu.property \
+			       --prefix-alloc-sections=.init
+$(obj)/%.pi.o: $(obj)/%.o FORCE
+	$(call if_changed,objcopy)
+
+$(obj)/lib-%.o: $(srctree)/lib/%.c FORCE
+	$(call if_changed_rule,cc_o_c)
+
+obj-y		:= kaslr_early.pi.o lib-fdt.pi.o lib-fdt_ro.pi.o
+extra-y		:= $(patsubst %.pi.o,%.o,$(obj-y))
diff --git a/arch/arm64/kernel/pi/kaslr_early.c b/arch/arm64/kernel/pi/kaslr_early.c
new file mode 100644
index 000000000000..17bff6e399e4
--- /dev/null
+++ b/arch/arm64/kernel/pi/kaslr_early.c
@@ -0,0 +1,110 @@
+// SPDX-License-Identifier: GPL-2.0-only
+// Copyright 2022 Google LLC
+// Author: Ard Biesheuvel <ardb@google.com>
+
+// NOTE: code in this file runs *very* early, and is not permitted to use
+// global variables or anything that relies on absolute addressing.
+
+#include <linux/libfdt.h>
+#include <linux/init.h>
+#include <linux/linkage.h>
+#include <linux/types.h>
+#include <linux/sizes.h>
+#include <linux/string.h>
+
+#include <asm/archrandom.h>
+#include <asm/memory.h>
+
+/* taken from lib/string.c */
+static char *__strstr(const char *s1, const char *s2)
+{
+	size_t l1, l2;
+
+	l2 = strlen(s2);
+	if (!l2)
+		return (char *)s1;
+	l1 = strlen(s1);
+	while (l1 >= l2) {
+		l1--;
+		if (!memcmp(s1, s2, l2))
+			return (char *)s1;
+		s1++;
+	}
+	return NULL;
+}
+static bool cmdline_contains_nokaslr(const u8 *cmdline)
+{
+	const u8 *str;
+
+	str = __strstr(cmdline, "nokaslr");
+	return str == cmdline || (str > cmdline && *(str - 1) == ' ');
+}
+
+static bool is_kaslr_disabled_cmdline(void *fdt)
+{
+	if (!IS_ENABLED(CONFIG_CMDLINE_FORCE)) {
+		int node;
+		const u8 *prop;
+
+		node = fdt_path_offset(fdt, "/chosen");
+		if (node < 0)
+			goto out;
+
+		prop = fdt_getprop(fdt, node, "bootargs", NULL);
+		if (!prop)
+			goto out;
+
+		if (cmdline_contains_nokaslr(prop))
+			return true;
+
+		if (IS_ENABLED(CONFIG_CMDLINE_EXTEND))
+			goto out;
+
+		return false;
+	}
+out:
+	return cmdline_contains_nokaslr(CONFIG_CMDLINE);
+}
+
+static u64 get_kaslr_seed(void *fdt)
+{
+	int node, len;
+	fdt64_t *prop;
+	u64 ret;
+
+	node = fdt_path_offset(fdt, "/chosen");
+	if (node < 0)
+		return 0;
+
+	prop = fdt_getprop_w(fdt, node, "kaslr-seed", &len);
+	if (!prop || len != sizeof(u64))
+		return 0;
+
+	ret = fdt64_to_cpu(*prop);
+	*prop = 0;
+	return ret;
+}
+
+asmlinkage u64 kaslr_early_init(void *fdt)
+{
+	u64 seed;
+
+	if (is_kaslr_disabled_cmdline(fdt))
+		return 0;
+
+	seed = get_kaslr_seed(fdt);
+	if (!seed) {
+		if (!__early_cpu_has_rndr() ||
+		    !__arm64_rndr((unsigned long *)&seed))
+			return 0;
+	}
+
+	/*
+	 * OK, so we are proceeding with KASLR enabled. Calculate a suitable
+	 * kernel image offset from the seed. Let's place the kernel in the
+	 * middle half of the VMALLOC area (VA_BITS_MIN - 2), and stay clear of
+	 * the lower and upper quarters to avoid colliding with other
+	 * allocations.
+	 */
+	return BIT(VA_BITS_MIN - 3) + (seed & GENMASK(VA_BITS_MIN - 3, 0));
+}
diff --git a/arch/arm64/kernel/probes/kprobes.c b/arch/arm64/kernel/probes/kprobes.c
index d9dfa82c1f18..c9e4d0720285 100644
--- a/arch/arm64/kernel/probes/kprobes.c
+++ b/arch/arm64/kernel/probes/kprobes.c
@@ -44,13 +44,28 @@ post_kprobe_handler(struct kprobe *, struct kprobe_ctlblk *, struct pt_regs *);
 static void __kprobes arch_prepare_ss_slot(struct kprobe *p)
 {
 	kprobe_opcode_t *addr = p->ainsn.api.insn;
-	void *addrs[] = {addr, addr + 1};
-	u32 insns[] = {p->opcode, BRK64_OPCODE_KPROBES_SS};
 
-	/* prepare insn slot */
-	aarch64_insn_patch_text(addrs, insns, 2);
-
-	flush_icache_range((uintptr_t)addr, (uintptr_t)(addr + MAX_INSN_SIZE));
+	/*
+	 * Prepare insn slot, Mark Rutland points out it depends on a coupe of
+	 * subtleties:
+	 *
+	 * - That the I-cache maintenance for these instructions is complete
+	 *   *before* the kprobe BRK is written (and aarch64_insn_patch_text_nosync()
+	 *   ensures this, but just omits causing a Context-Synchronization-Event
+	 *   on all CPUS).
+	 *
+	 * - That the kprobe BRK results in an exception (and consequently a
+	 *   Context-Synchronoization-Event), which ensures that the CPU will
+	 *   fetch thesingle-step slot instructions *after* this, ensuring that
+	 *   the new instructions are used
+	 *
+	 * It supposes to place ISB after patching to guarantee I-cache maintenance
+	 * is observed on all CPUS, however, single-step slot is installed in
+	 * the BRK exception handler, so it is unnecessary to generate
+	 * Contex-Synchronization-Event via ISB again.
+	 */
+	aarch64_insn_patch_text_nosync(addr, p->opcode);
+	aarch64_insn_patch_text_nosync(addr + 1, BRK64_OPCODE_KPROBES_SS);
 
 	/*
 	 * Needs restoring of return address after stepping xol.
@@ -335,7 +350,7 @@ static void __kprobes kprobe_handler(struct pt_regs *regs)
 }
 
 static int __kprobes
-kprobe_breakpoint_ss_handler(struct pt_regs *regs, unsigned int esr)
+kprobe_breakpoint_ss_handler(struct pt_regs *regs, unsigned long esr)
 {
 	struct kprobe_ctlblk *kcb = get_kprobe_ctlblk();
 	unsigned long addr = instruction_pointer(regs);
@@ -359,7 +374,7 @@ static struct break_hook kprobes_break_ss_hook = {
 };
 
 static int __kprobes
-kprobe_breakpoint_handler(struct pt_regs *regs, unsigned int esr)
+kprobe_breakpoint_handler(struct pt_regs *regs, unsigned long esr)
 {
 	kprobe_handler(regs);
 	return DBG_HOOK_HANDLED;
diff --git a/arch/arm64/kernel/probes/uprobes.c b/arch/arm64/kernel/probes/uprobes.c
index 9be668f3f034..d49aef2657cd 100644
--- a/arch/arm64/kernel/probes/uprobes.c
+++ b/arch/arm64/kernel/probes/uprobes.c
@@ -166,7 +166,7 @@ int arch_uprobe_exception_notify(struct notifier_block *self,
 }
 
 static int uprobe_breakpoint_handler(struct pt_regs *regs,
-		unsigned int esr)
+				     unsigned long esr)
 {
 	if (uprobe_pre_sstep_notifier(regs))
 		return DBG_HOOK_HANDLED;
@@ -175,7 +175,7 @@ static int uprobe_breakpoint_handler(struct pt_regs *regs,
 }
 
 static int uprobe_single_step_handler(struct pt_regs *regs,
-		unsigned int esr)
+				      unsigned long esr)
 {
 	struct uprobe_task *utask = current->utask;
 
diff --git a/arch/arm64/kernel/process.c b/arch/arm64/kernel/process.c
index aacf2f5559a8..044a7d7f1f6a 100644
--- a/arch/arm64/kernel/process.c
+++ b/arch/arm64/kernel/process.c
@@ -40,6 +40,7 @@
 #include <linux/percpu.h>
 #include <linux/thread_info.h>
 #include <linux/prctl.h>
+#include <linux/stacktrace.h>
 
 #include <asm/alternative.h>
 #include <asm/compat.h>
@@ -110,8 +111,7 @@ void machine_power_off(void)
 {
 	local_irq_disable();
 	smp_send_stop();
-	if (pm_power_off)
-		pm_power_off();
+	do_kernel_power_off();
 }
 
 /*
@@ -249,6 +249,8 @@ void show_regs(struct pt_regs *regs)
 static void tls_thread_flush(void)
 {
 	write_sysreg(0, tpidr_el0);
+	if (system_supports_tpidr2())
+		write_sysreg_s(0, SYS_TPIDR2_EL0);
 
 	if (is_compat_task()) {
 		current->thread.uw.tp_value = 0;
@@ -277,10 +279,6 @@ void flush_thread(void)
 	flush_tagged_addr_state();
 }
 
-void release_thread(struct task_struct *dead_task)
-{
-}
-
 void arch_release_task_struct(struct task_struct *tsk)
 {
 	fpsimd_release_task(tsk);
@@ -297,16 +295,42 @@ int arch_dup_task_struct(struct task_struct *dst, struct task_struct *src)
 
 	/*
 	 * Detach src's sve_state (if any) from dst so that it does not
-	 * get erroneously used or freed prematurely.  dst's sve_state
+	 * get erroneously used or freed prematurely.  dst's copies
 	 * will be allocated on demand later on if dst uses SVE.
 	 * For consistency, also clear TIF_SVE here: this could be done
 	 * later in copy_process(), but to avoid tripping up future
-	 * maintainers it is best not to leave TIF_SVE and sve_state in
+	 * maintainers it is best not to leave TIF flags and buffers in
 	 * an inconsistent state, even temporarily.
 	 */
 	dst->thread.sve_state = NULL;
 	clear_tsk_thread_flag(dst, TIF_SVE);
 
+	/*
+	 * In the unlikely event that we create a new thread with ZA
+	 * enabled we should retain the ZA state so duplicate it here.
+	 * This may be shortly freed if we exec() or if CLONE_SETTLS
+	 * but it's simpler to do it here. To avoid confusing the rest
+	 * of the code ensure that we have a sve_state allocated
+	 * whenever za_state is allocated.
+	 */
+	if (thread_za_enabled(&src->thread)) {
+		dst->thread.sve_state = kzalloc(sve_state_size(src),
+						GFP_KERNEL);
+		if (!dst->thread.sve_state)
+			return -ENOMEM;
+		dst->thread.za_state = kmemdup(src->thread.za_state,
+					       za_state_size(src),
+					       GFP_KERNEL);
+		if (!dst->thread.za_state) {
+			kfree(dst->thread.sve_state);
+			dst->thread.sve_state = NULL;
+			return -ENOMEM;
+		}
+	} else {
+		dst->thread.za_state = NULL;
+		clear_tsk_thread_flag(dst, TIF_SME);
+	}
+
 	/* clear any pending asynchronous tag fault raised by the parent */
 	clear_tsk_thread_flag(dst, TIF_MTE_ASYNC_FAULT);
 
@@ -315,9 +339,11 @@ int arch_dup_task_struct(struct task_struct *dst, struct task_struct *src)
 
 asmlinkage void ret_from_fork(void) asm("ret_from_fork");
 
-int copy_thread(unsigned long clone_flags, unsigned long stack_start,
-		unsigned long stk_sz, struct task_struct *p, unsigned long tls)
+int copy_thread(struct task_struct *p, const struct kernel_clone_args *args)
 {
+	unsigned long clone_flags = args->flags;
+	unsigned long stack_start = args->stack;
+	unsigned long tls = args->tls;
 	struct pt_regs *childregs = task_pt_regs(p);
 
 	memset(&p->thread.cpu_context, 0, sizeof(struct cpu_context));
@@ -333,7 +359,7 @@ int copy_thread(unsigned long clone_flags, unsigned long stack_start,
 
 	ptrauth_thread_init_kernel(p);
 
-	if (likely(!(p->flags & (PF_KTHREAD | PF_IO_WORKER)))) {
+	if (likely(!args->fn)) {
 		*childregs = *current_pt_regs();
 		childregs->regs[0] = 0;
 
@@ -342,6 +368,8 @@ int copy_thread(unsigned long clone_flags, unsigned long stack_start,
 		 * out-of-sync with the saved value.
 		 */
 		*task_user_tls(p) = read_sysreg(tpidr_el0);
+		if (system_supports_tpidr2())
+			p->thread.tpidr2_el0 = read_sysreg_s(SYS_TPIDR2_EL0);
 
 		if (stack_start) {
 			if (is_compat_thread(task_thread_info(p)))
@@ -352,10 +380,12 @@ int copy_thread(unsigned long clone_flags, unsigned long stack_start,
 
 		/*
 		 * If a TLS pointer was passed to clone, use it for the new
-		 * thread.
+		 * thread.  We also reset TPIDR2 if it's in use.
 		 */
-		if (clone_flags & CLONE_SETTLS)
+		if (clone_flags & CLONE_SETTLS) {
 			p->thread.uw.tp_value = tls;
+			p->thread.tpidr2_el0 = 0;
+		}
 	} else {
 		/*
 		 * A kthread has no context to ERET to, so ensure any buggy
@@ -367,8 +397,8 @@ int copy_thread(unsigned long clone_flags, unsigned long stack_start,
 		memset(childregs, 0, sizeof(struct pt_regs));
 		childregs->pstate = PSR_MODE_EL1h | PSR_IL_BIT;
 
-		p->thread.cpu_context.x19 = stack_start;
-		p->thread.cpu_context.x20 = stk_sz;
+		p->thread.cpu_context.x19 = (unsigned long)args->fn;
+		p->thread.cpu_context.x20 = (unsigned long)args->fn_arg;
 	}
 	p->thread.cpu_context.pc = (unsigned long)ret_from_fork;
 	p->thread.cpu_context.sp = (unsigned long)childregs;
@@ -386,6 +416,8 @@ int copy_thread(unsigned long clone_flags, unsigned long stack_start,
 void tls_preserve_current_state(void)
 {
 	*task_user_tls(current) = read_sysreg(tpidr_el0);
+	if (system_supports_tpidr2() && !is_compat_task())
+		current->thread.tpidr2_el0 = read_sysreg_s(SYS_TPIDR2_EL0);
 }
 
 static void tls_thread_switch(struct task_struct *next)
@@ -398,6 +430,8 @@ static void tls_thread_switch(struct task_struct *next)
 		write_sysreg(0, tpidrro_el0);
 
 	write_sysreg(*task_user_tls(next), tpidr_el0);
+	if (system_supports_tpidr2())
+		write_sysreg_s(next->thread.tpidr2_el0, SYS_TPIDR2_EL0);
 }
 
 /*
@@ -439,34 +473,26 @@ static void entry_task_switch(struct task_struct *next)
 
 /*
  * ARM erratum 1418040 handling, affecting the 32bit view of CNTVCT.
- * Assuming the virtual counter is enabled at the beginning of times:
- *
- * - disable access when switching from a 64bit task to a 32bit task
- * - enable access when switching from a 32bit task to a 64bit task
+ * Ensure access is disabled when switching to a 32bit task, ensure
+ * access is enabled when switching to a 64bit task.
  */
-static void erratum_1418040_thread_switch(struct task_struct *prev,
-					  struct task_struct *next)
+static void erratum_1418040_thread_switch(struct task_struct *next)
 {
-	bool prev32, next32;
-	u64 val;
-
-	if (!IS_ENABLED(CONFIG_ARM64_ERRATUM_1418040))
+	if (!IS_ENABLED(CONFIG_ARM64_ERRATUM_1418040) ||
+	    !this_cpu_has_cap(ARM64_WORKAROUND_1418040))
 		return;
 
-	prev32 = is_compat_thread(task_thread_info(prev));
-	next32 = is_compat_thread(task_thread_info(next));
-
-	if (prev32 == next32 || !this_cpu_has_cap(ARM64_WORKAROUND_1418040))
-		return;
-
-	val = read_sysreg(cntkctl_el1);
-
-	if (!next32)
-		val |= ARCH_TIMER_USR_VCT_ACCESS_EN;
+	if (is_compat_thread(task_thread_info(next)))
+		sysreg_clear_set(cntkctl_el1, ARCH_TIMER_USR_VCT_ACCESS_EN, 0);
 	else
-		val &= ~ARCH_TIMER_USR_VCT_ACCESS_EN;
+		sysreg_clear_set(cntkctl_el1, 0, ARCH_TIMER_USR_VCT_ACCESS_EN);
+}
 
-	write_sysreg(val, cntkctl_el1);
+static void erratum_1418040_new_exec(void)
+{
+	preempt_disable();
+	erratum_1418040_thread_switch(current);
+	preempt_enable();
 }
 
 /*
@@ -490,7 +516,8 @@ void update_sctlr_el1(u64 sctlr)
 /*
  * Thread switching.
  */
-__notrace_funcgraph struct task_struct *__switch_to(struct task_struct *prev,
+__notrace_funcgraph __sched
+struct task_struct *__switch_to(struct task_struct *prev,
 				struct task_struct *next)
 {
 	struct task_struct *last;
@@ -501,7 +528,7 @@ __notrace_funcgraph struct task_struct *__switch_to(struct task_struct *prev,
 	contextidr_thread_switch(next);
 	entry_task_switch(next);
 	ssbs_thread_switch(next);
-	erratum_1418040_thread_switch(prev, next);
+	erratum_1418040_thread_switch(next);
 	ptrauth_thread_switch_user(next);
 
 	/*
@@ -528,36 +555,43 @@ __notrace_funcgraph struct task_struct *__switch_to(struct task_struct *prev,
 	return last;
 }
 
+struct wchan_info {
+	unsigned long	pc;
+	int		count;
+};
+
+static bool get_wchan_cb(void *arg, unsigned long pc)
+{
+	struct wchan_info *wchan_info = arg;
+
+	if (!in_sched_functions(pc)) {
+		wchan_info->pc = pc;
+		return false;
+	}
+	return wchan_info->count++ < 16;
+}
+
 unsigned long __get_wchan(struct task_struct *p)
 {
-	struct stackframe frame;
-	unsigned long stack_page, ret = 0;
-	int count = 0;
+	struct wchan_info wchan_info = {
+		.pc = 0,
+		.count = 0,
+	};
 
-	stack_page = (unsigned long)try_get_task_stack(p);
-	if (!stack_page)
+	if (!try_get_task_stack(p))
 		return 0;
 
-	start_backtrace(&frame, thread_saved_fp(p), thread_saved_pc(p));
+	arch_stack_walk(get_wchan_cb, &wchan_info, p, NULL);
 
-	do {
-		if (unwind_frame(p, &frame))
-			goto out;
-		if (!in_sched_functions(frame.pc)) {
-			ret = frame.pc;
-			goto out;
-		}
-	} while (count++ < 16);
-
-out:
 	put_task_stack(p);
-	return ret;
+
+	return wchan_info.pc;
 }
 
 unsigned long arch_align_stack(unsigned long sp)
 {
 	if (!(current->personality & ADDR_NO_RANDOMIZE) && randomize_va_space)
-		sp -= get_random_int() & ~PAGE_MASK;
+		sp -= prandom_u32_max(PAGE_SIZE);
 	return sp & ~0xf;
 }
 
@@ -611,6 +645,7 @@ void arch_setup_new_exec(void)
 	current->mm->context.flags = mmflags;
 	ptrauth_thread_init_user();
 	mte_thread_init_user();
+	erratum_1418040_new_exec();
 
 	if (task_spec_ssb_noexec(current)) {
 		arch_prctl_spec_ctrl_set(current, PR_SPEC_STORE_BYPASS,
@@ -633,7 +668,8 @@ long set_tagged_addr_ctrl(struct task_struct *task, unsigned long arg)
 		return -EINVAL;
 
 	if (system_supports_mte())
-		valid_mask |= PR_MTE_TCF_MASK | PR_MTE_TAG_MASK;
+		valid_mask |= PR_MTE_TCF_SYNC | PR_MTE_TCF_ASYNC \
+			| PR_MTE_TAG_MASK;
 
 	if (arg & ~valid_mask)
 		return -EINVAL;
diff --git a/arch/arm64/kernel/proton-pack.c b/arch/arm64/kernel/proton-pack.c
index 902e4084c477..bfce41c2a53b 100644
--- a/arch/arm64/kernel/proton-pack.c
+++ b/arch/arm64/kernel/proton-pack.c
@@ -18,15 +18,18 @@
  */
 
 #include <linux/arm-smccc.h>
+#include <linux/bpf.h>
 #include <linux/cpu.h>
 #include <linux/device.h>
 #include <linux/nospec.h>
 #include <linux/prctl.h>
 #include <linux/sched/task_stack.h>
 
+#include <asm/debug-monitors.h>
 #include <asm/insn.h>
 #include <asm/spectre.h>
 #include <asm/traps.h>
+#include <asm/vectors.h>
 #include <asm/virt.h>
 
 /*
@@ -96,14 +99,51 @@ static bool spectre_v2_mitigations_off(void)
 	return ret;
 }
 
+static const char *get_bhb_affected_string(enum mitigation_state bhb_state)
+{
+	switch (bhb_state) {
+	case SPECTRE_UNAFFECTED:
+		return "";
+	default:
+	case SPECTRE_VULNERABLE:
+		return ", but not BHB";
+	case SPECTRE_MITIGATED:
+		return ", BHB";
+	}
+}
+
+static bool _unprivileged_ebpf_enabled(void)
+{
+#ifdef CONFIG_BPF_SYSCALL
+	return !sysctl_unprivileged_bpf_disabled;
+#else
+	return false;
+#endif
+}
+
 ssize_t cpu_show_spectre_v2(struct device *dev, struct device_attribute *attr,
 			    char *buf)
 {
+	enum mitigation_state bhb_state = arm64_get_spectre_bhb_state();
+	const char *bhb_str = get_bhb_affected_string(bhb_state);
+	const char *v2_str = "Branch predictor hardening";
+
 	switch (spectre_v2_state) {
 	case SPECTRE_UNAFFECTED:
-		return sprintf(buf, "Not affected\n");
+		if (bhb_state == SPECTRE_UNAFFECTED)
+			return sprintf(buf, "Not affected\n");
+
+		/*
+		 * Platforms affected by Spectre-BHB can't report
+		 * "Not affected" for Spectre-v2.
+		 */
+		v2_str = "CSV2";
+		fallthrough;
 	case SPECTRE_MITIGATED:
-		return sprintf(buf, "Mitigation: Branch predictor hardening\n");
+		if (bhb_state == SPECTRE_MITIGATED && _unprivileged_ebpf_enabled())
+			return sprintf(buf, "Vulnerable: Unprivileged eBPF enabled\n");
+
+		return sprintf(buf, "Mitigation: %s%s\n", v2_str, bhb_str);
 	case SPECTRE_VULNERABLE:
 		fallthrough;
 	default:
@@ -128,7 +168,7 @@ static enum mitigation_state spectre_v2_get_cpu_hw_mitigation_state(void)
 
 	/* If the CPU has CSV2 set, we're safe */
 	pfr0 = read_cpuid(ID_AA64PFR0_EL1);
-	if (cpuid_feature_extract_unsigned_field(pfr0, ID_AA64PFR0_CSV2_SHIFT))
+	if (cpuid_feature_extract_unsigned_field(pfr0, ID_AA64PFR0_EL1_CSV2_SHIFT))
 		return SPECTRE_UNAFFECTED;
 
 	/* Alternatively, we have a list of unaffected CPUs */
@@ -193,17 +233,20 @@ static void install_bp_hardening_cb(bp_hardening_cb_t fn)
 	__this_cpu_write(bp_hardening_data.slot, HYP_VECTOR_SPECTRE_DIRECT);
 }
 
-static void call_smc_arch_workaround_1(void)
+/* Called during entry so must be noinstr */
+static noinstr void call_smc_arch_workaround_1(void)
 {
 	arm_smccc_1_1_smc(ARM_SMCCC_ARCH_WORKAROUND_1, NULL);
 }
 
-static void call_hvc_arch_workaround_1(void)
+/* Called during entry so must be noinstr */
+static noinstr void call_hvc_arch_workaround_1(void)
 {
 	arm_smccc_1_1_hvc(ARM_SMCCC_ARCH_WORKAROUND_1, NULL);
 }
 
-static void qcom_link_stack_sanitisation(void)
+/* Called during entry so must be noinstr */
+static noinstr void qcom_link_stack_sanitisation(void)
 {
 	u64 tmp;
 
@@ -543,7 +586,7 @@ void __init spectre_v4_patch_fw_mitigation_enable(struct alt_instr *alt,
 	if (spectre_v4_mitigations_off())
 		return;
 
-	if (cpus_have_final_cap(ARM64_SSBS))
+	if (cpus_have_cap(ARM64_SSBS))
 		return;
 
 	if (spectre_v4_mitigations_dynamic())
@@ -554,9 +597,9 @@ void __init spectre_v4_patch_fw_mitigation_enable(struct alt_instr *alt,
  * Patch a NOP in the Spectre-v4 mitigation code with an SMC/HVC instruction
  * to call into firmware to adjust the mitigation state.
  */
-void __init spectre_v4_patch_fw_mitigation_conduit(struct alt_instr *alt,
-						   __le32 *origptr,
-						   __le32 *updptr, int nr_inst)
+void __init smccc_patch_fw_mitigation_conduit(struct alt_instr *alt,
+					       __le32 *origptr,
+					       __le32 *updptr, int nr_inst)
 {
 	u32 insn;
 
@@ -770,3 +813,359 @@ int arch_prctl_spec_ctrl_get(struct task_struct *task, unsigned long which)
 		return -ENODEV;
 	}
 }
+
+/*
+ * Spectre BHB.
+ *
+ * A CPU is either:
+ * - Mitigated by a branchy loop a CPU specific number of times, and listed
+ *   in our "loop mitigated list".
+ * - Mitigated in software by the firmware Spectre v2 call.
+ * - Has the ClearBHB instruction to perform the mitigation.
+ * - Has the 'Exception Clears Branch History Buffer' (ECBHB) feature, so no
+ *   software mitigation in the vectors is needed.
+ * - Has CSV2.3, so is unaffected.
+ */
+static enum mitigation_state spectre_bhb_state;
+
+enum mitigation_state arm64_get_spectre_bhb_state(void)
+{
+	return spectre_bhb_state;
+}
+
+enum bhb_mitigation_bits {
+	BHB_LOOP,
+	BHB_FW,
+	BHB_HW,
+	BHB_INSN,
+};
+static unsigned long system_bhb_mitigations;
+
+/*
+ * This must be called with SCOPE_LOCAL_CPU for each type of CPU, before any
+ * SCOPE_SYSTEM call will give the right answer.
+ */
+u8 spectre_bhb_loop_affected(int scope)
+{
+	u8 k = 0;
+	static u8 max_bhb_k;
+
+	if (scope == SCOPE_LOCAL_CPU) {
+		static const struct midr_range spectre_bhb_k32_list[] = {
+			MIDR_ALL_VERSIONS(MIDR_CORTEX_A78),
+			MIDR_ALL_VERSIONS(MIDR_CORTEX_A78AE),
+			MIDR_ALL_VERSIONS(MIDR_CORTEX_A78C),
+			MIDR_ALL_VERSIONS(MIDR_CORTEX_X1),
+			MIDR_ALL_VERSIONS(MIDR_CORTEX_A710),
+			MIDR_ALL_VERSIONS(MIDR_CORTEX_X2),
+			MIDR_ALL_VERSIONS(MIDR_NEOVERSE_N2),
+			MIDR_ALL_VERSIONS(MIDR_NEOVERSE_V1),
+			{},
+		};
+		static const struct midr_range spectre_bhb_k24_list[] = {
+			MIDR_ALL_VERSIONS(MIDR_CORTEX_A76),
+			MIDR_ALL_VERSIONS(MIDR_CORTEX_A77),
+			MIDR_ALL_VERSIONS(MIDR_NEOVERSE_N1),
+			{},
+		};
+		static const struct midr_range spectre_bhb_k11_list[] = {
+			MIDR_ALL_VERSIONS(MIDR_AMPERE1),
+			{},
+		};
+		static const struct midr_range spectre_bhb_k8_list[] = {
+			MIDR_ALL_VERSIONS(MIDR_CORTEX_A72),
+			MIDR_ALL_VERSIONS(MIDR_CORTEX_A57),
+			{},
+		};
+
+		if (is_midr_in_range_list(read_cpuid_id(), spectre_bhb_k32_list))
+			k = 32;
+		else if (is_midr_in_range_list(read_cpuid_id(), spectre_bhb_k24_list))
+			k = 24;
+		else if (is_midr_in_range_list(read_cpuid_id(), spectre_bhb_k11_list))
+			k = 11;
+		else if (is_midr_in_range_list(read_cpuid_id(), spectre_bhb_k8_list))
+			k =  8;
+
+		max_bhb_k = max(max_bhb_k, k);
+	} else {
+		k = max_bhb_k;
+	}
+
+	return k;
+}
+
+static enum mitigation_state spectre_bhb_get_cpu_fw_mitigation_state(void)
+{
+	int ret;
+	struct arm_smccc_res res;
+
+	arm_smccc_1_1_invoke(ARM_SMCCC_ARCH_FEATURES_FUNC_ID,
+			     ARM_SMCCC_ARCH_WORKAROUND_3, &res);
+
+	ret = res.a0;
+	switch (ret) {
+	case SMCCC_RET_SUCCESS:
+		return SPECTRE_MITIGATED;
+	case SMCCC_ARCH_WORKAROUND_RET_UNAFFECTED:
+		return SPECTRE_UNAFFECTED;
+	default:
+		fallthrough;
+	case SMCCC_RET_NOT_SUPPORTED:
+		return SPECTRE_VULNERABLE;
+	}
+}
+
+static bool is_spectre_bhb_fw_affected(int scope)
+{
+	static bool system_affected;
+	enum mitigation_state fw_state;
+	bool has_smccc = arm_smccc_1_1_get_conduit() != SMCCC_CONDUIT_NONE;
+	static const struct midr_range spectre_bhb_firmware_mitigated_list[] = {
+		MIDR_ALL_VERSIONS(MIDR_CORTEX_A73),
+		MIDR_ALL_VERSIONS(MIDR_CORTEX_A75),
+		{},
+	};
+	bool cpu_in_list = is_midr_in_range_list(read_cpuid_id(),
+					 spectre_bhb_firmware_mitigated_list);
+
+	if (scope != SCOPE_LOCAL_CPU)
+		return system_affected;
+
+	fw_state = spectre_bhb_get_cpu_fw_mitigation_state();
+	if (cpu_in_list || (has_smccc && fw_state == SPECTRE_MITIGATED)) {
+		system_affected = true;
+		return true;
+	}
+
+	return false;
+}
+
+static bool supports_ecbhb(int scope)
+{
+	u64 mmfr1;
+
+	if (scope == SCOPE_LOCAL_CPU)
+		mmfr1 = read_sysreg_s(SYS_ID_AA64MMFR1_EL1);
+	else
+		mmfr1 = read_sanitised_ftr_reg(SYS_ID_AA64MMFR1_EL1);
+
+	return cpuid_feature_extract_unsigned_field(mmfr1,
+						    ID_AA64MMFR1_EL1_ECBHB_SHIFT);
+}
+
+bool is_spectre_bhb_affected(const struct arm64_cpu_capabilities *entry,
+			     int scope)
+{
+	WARN_ON(scope != SCOPE_LOCAL_CPU || preemptible());
+
+	if (supports_csv2p3(scope))
+		return false;
+
+	if (supports_clearbhb(scope))
+		return true;
+
+	if (spectre_bhb_loop_affected(scope))
+		return true;
+
+	if (is_spectre_bhb_fw_affected(scope))
+		return true;
+
+	return false;
+}
+
+static void this_cpu_set_vectors(enum arm64_bp_harden_el1_vectors slot)
+{
+	const char *v = arm64_get_bp_hardening_vector(slot);
+
+	if (slot < 0)
+		return;
+
+	__this_cpu_write(this_cpu_vector, v);
+
+	/*
+	 * When KPTI is in use, the vectors are switched when exiting to
+	 * user-space.
+	 */
+	if (arm64_kernel_unmapped_at_el0())
+		return;
+
+	write_sysreg(v, vbar_el1);
+	isb();
+}
+
+static bool __read_mostly __nospectre_bhb;
+static int __init parse_spectre_bhb_param(char *str)
+{
+	__nospectre_bhb = true;
+	return 0;
+}
+early_param("nospectre_bhb", parse_spectre_bhb_param);
+
+void spectre_bhb_enable_mitigation(const struct arm64_cpu_capabilities *entry)
+{
+	bp_hardening_cb_t cpu_cb;
+	enum mitigation_state fw_state, state = SPECTRE_VULNERABLE;
+	struct bp_hardening_data *data = this_cpu_ptr(&bp_hardening_data);
+
+	if (!is_spectre_bhb_affected(entry, SCOPE_LOCAL_CPU))
+		return;
+
+	if (arm64_get_spectre_v2_state() == SPECTRE_VULNERABLE) {
+		/* No point mitigating Spectre-BHB alone. */
+	} else if (!IS_ENABLED(CONFIG_MITIGATE_SPECTRE_BRANCH_HISTORY)) {
+		pr_info_once("spectre-bhb mitigation disabled by compile time option\n");
+	} else if (cpu_mitigations_off() || __nospectre_bhb) {
+		pr_info_once("spectre-bhb mitigation disabled by command line option\n");
+	} else if (supports_ecbhb(SCOPE_LOCAL_CPU)) {
+		state = SPECTRE_MITIGATED;
+		set_bit(BHB_HW, &system_bhb_mitigations);
+	} else if (supports_clearbhb(SCOPE_LOCAL_CPU)) {
+		/*
+		 * Ensure KVM uses the indirect vector which will have ClearBHB
+		 * added.
+		 */
+		if (!data->slot)
+			data->slot = HYP_VECTOR_INDIRECT;
+
+		this_cpu_set_vectors(EL1_VECTOR_BHB_CLEAR_INSN);
+		state = SPECTRE_MITIGATED;
+		set_bit(BHB_INSN, &system_bhb_mitigations);
+	} else if (spectre_bhb_loop_affected(SCOPE_LOCAL_CPU)) {
+		/*
+		 * Ensure KVM uses the indirect vector which will have the
+		 * branchy-loop added. A57/A72-r0 will already have selected
+		 * the spectre-indirect vector, which is sufficient for BHB
+		 * too.
+		 */
+		if (!data->slot)
+			data->slot = HYP_VECTOR_INDIRECT;
+
+		this_cpu_set_vectors(EL1_VECTOR_BHB_LOOP);
+		state = SPECTRE_MITIGATED;
+		set_bit(BHB_LOOP, &system_bhb_mitigations);
+	} else if (is_spectre_bhb_fw_affected(SCOPE_LOCAL_CPU)) {
+		fw_state = spectre_bhb_get_cpu_fw_mitigation_state();
+		if (fw_state == SPECTRE_MITIGATED) {
+			/*
+			 * Ensure KVM uses one of the spectre bp_hardening
+			 * vectors. The indirect vector doesn't include the EL3
+			 * call, so needs upgrading to
+			 * HYP_VECTOR_SPECTRE_INDIRECT.
+			 */
+			if (!data->slot || data->slot == HYP_VECTOR_INDIRECT)
+				data->slot += 1;
+
+			this_cpu_set_vectors(EL1_VECTOR_BHB_FW);
+
+			/*
+			 * The WA3 call in the vectors supersedes the WA1 call
+			 * made during context-switch. Uninstall any firmware
+			 * bp_hardening callback.
+			 */
+			cpu_cb = spectre_v2_get_sw_mitigation_cb();
+			if (__this_cpu_read(bp_hardening_data.fn) != cpu_cb)
+				__this_cpu_write(bp_hardening_data.fn, NULL);
+
+			state = SPECTRE_MITIGATED;
+			set_bit(BHB_FW, &system_bhb_mitigations);
+		}
+	}
+
+	update_mitigation_state(&spectre_bhb_state, state);
+}
+
+/* Patched to NOP when enabled */
+void noinstr spectre_bhb_patch_loop_mitigation_enable(struct alt_instr *alt,
+						     __le32 *origptr,
+						      __le32 *updptr, int nr_inst)
+{
+	BUG_ON(nr_inst != 1);
+
+	if (test_bit(BHB_LOOP, &system_bhb_mitigations))
+		*updptr++ = cpu_to_le32(aarch64_insn_gen_nop());
+}
+
+/* Patched to NOP when enabled */
+void noinstr spectre_bhb_patch_fw_mitigation_enabled(struct alt_instr *alt,
+						   __le32 *origptr,
+						   __le32 *updptr, int nr_inst)
+{
+	BUG_ON(nr_inst != 1);
+
+	if (test_bit(BHB_FW, &system_bhb_mitigations))
+		*updptr++ = cpu_to_le32(aarch64_insn_gen_nop());
+}
+
+/* Patched to correct the immediate */
+void noinstr spectre_bhb_patch_loop_iter(struct alt_instr *alt,
+				   __le32 *origptr, __le32 *updptr, int nr_inst)
+{
+	u8 rd;
+	u32 insn;
+	u16 loop_count = spectre_bhb_loop_affected(SCOPE_SYSTEM);
+
+	BUG_ON(nr_inst != 1); /* MOV -> MOV */
+
+	if (!IS_ENABLED(CONFIG_MITIGATE_SPECTRE_BRANCH_HISTORY))
+		return;
+
+	insn = le32_to_cpu(*origptr);
+	rd = aarch64_insn_decode_register(AARCH64_INSN_REGTYPE_RD, insn);
+	insn = aarch64_insn_gen_movewide(rd, loop_count, 0,
+					 AARCH64_INSN_VARIANT_64BIT,
+					 AARCH64_INSN_MOVEWIDE_ZERO);
+	*updptr++ = cpu_to_le32(insn);
+}
+
+/* Patched to mov WA3 when supported */
+void noinstr spectre_bhb_patch_wa3(struct alt_instr *alt,
+				   __le32 *origptr, __le32 *updptr, int nr_inst)
+{
+	u8 rd;
+	u32 insn;
+
+	BUG_ON(nr_inst != 1); /* MOV -> MOV */
+
+	if (!IS_ENABLED(CONFIG_MITIGATE_SPECTRE_BRANCH_HISTORY) ||
+	    !test_bit(BHB_FW, &system_bhb_mitigations))
+		return;
+
+	insn = le32_to_cpu(*origptr);
+	rd = aarch64_insn_decode_register(AARCH64_INSN_REGTYPE_RD, insn);
+
+	insn = aarch64_insn_gen_logical_immediate(AARCH64_INSN_LOGIC_ORR,
+						  AARCH64_INSN_VARIANT_32BIT,
+						  AARCH64_INSN_REG_ZR, rd,
+						  ARM_SMCCC_ARCH_WORKAROUND_3);
+	if (WARN_ON_ONCE(insn == AARCH64_BREAK_FAULT))
+		return;
+
+	*updptr++ = cpu_to_le32(insn);
+}
+
+/* Patched to NOP when not supported */
+void __init spectre_bhb_patch_clearbhb(struct alt_instr *alt,
+				   __le32 *origptr, __le32 *updptr, int nr_inst)
+{
+	BUG_ON(nr_inst != 2);
+
+	if (test_bit(BHB_INSN, &system_bhb_mitigations))
+		return;
+
+	*updptr++ = cpu_to_le32(aarch64_insn_gen_nop());
+	*updptr++ = cpu_to_le32(aarch64_insn_gen_nop());
+}
+
+#ifdef CONFIG_BPF_SYSCALL
+#define EBPF_WARN "Unprivileged eBPF is enabled, data leaks possible via Spectre v2 BHB attacks!\n"
+void unpriv_ebpf_notify(int new_state)
+{
+	if (spectre_v2_state == SPECTRE_VULNERABLE ||
+	    spectre_bhb_state != SPECTRE_MITIGATED)
+		return;
+
+	if (!new_state)
+		pr_err("WARNING: %s", EBPF_WARN);
+}
+#endif
diff --git a/arch/arm64/kernel/psci.c b/arch/arm64/kernel/psci.c
index ab7f4c476104..29a8e444db83 100644
--- a/arch/arm64/kernel/psci.c
+++ b/arch/arm64/kernel/psci.c
@@ -38,7 +38,7 @@ static int __init cpu_psci_cpu_prepare(unsigned int cpu)
 
 static int cpu_psci_cpu_boot(unsigned int cpu)
 {
-	phys_addr_t pa_secondary_entry = __pa_symbol(function_nocfi(secondary_entry));
+	phys_addr_t pa_secondary_entry = __pa_symbol(secondary_entry);
 	int err = psci_ops.cpu_on(cpu_logical_map(cpu), pa_secondary_entry);
 	if (err)
 		pr_err("failed to boot CPU%d (%d)\n", cpu, err);
diff --git a/arch/arm64/kernel/ptrace.c b/arch/arm64/kernel/ptrace.c
index 88a9034fb9b5..c2fb5755bbec 100644
--- a/arch/arm64/kernel/ptrace.c
+++ b/arch/arm64/kernel/ptrace.c
@@ -27,7 +27,6 @@
 #include <linux/perf_event.h>
 #include <linux/hw_breakpoint.h>
 #include <linux/regset.h>
-#include <linux/tracehook.h>
 #include <linux/elf.h>
 
 #include <asm/compat.h>
@@ -122,7 +121,7 @@ static bool regs_within_kernel_stack(struct pt_regs *regs, unsigned long addr)
 {
 	return ((addr & ~(THREAD_SIZE - 1))  ==
 		(kernel_stack_pointer(regs) & ~(THREAD_SIZE - 1))) ||
-		on_irq_stack(addr, sizeof(unsigned long), NULL);
+		on_irq_stack(addr, sizeof(unsigned long));
 }
 
 /**
@@ -667,10 +666,18 @@ static int fpr_set(struct task_struct *target, const struct user_regset *regset,
 static int tls_get(struct task_struct *target, const struct user_regset *regset,
 		   struct membuf to)
 {
+	int ret;
+
 	if (target == current)
 		tls_preserve_current_state();
 
-	return membuf_store(&to, target->thread.uw.tp_value);
+	ret = membuf_store(&to, target->thread.uw.tp_value);
+	if (system_supports_tpidr2())
+		ret = membuf_store(&to, target->thread.tpidr2_el0);
+	else
+		ret = membuf_zero(&to, sizeof(u64));
+
+	return ret;
 }
 
 static int tls_set(struct task_struct *target, const struct user_regset *regset,
@@ -678,13 +685,20 @@ static int tls_set(struct task_struct *target, const struct user_regset *regset,
 		   const void *kbuf, const void __user *ubuf)
 {
 	int ret;
-	unsigned long tls = target->thread.uw.tp_value;
+	unsigned long tls[2];
 
-	ret = user_regset_copyin(&pos, &count, &kbuf, &ubuf, &tls, 0, -1);
+	tls[0] = target->thread.uw.tp_value;
+	if (system_supports_sme())
+		tls[1] = target->thread.tpidr2_el0;
+
+	ret = user_regset_copyin(&pos, &count, &kbuf, &ubuf, tls, 0, count);
 	if (ret)
 		return ret;
 
-	target->thread.uw.tp_value = tls;
+	target->thread.uw.tp_value = tls[0];
+	if (system_supports_sme())
+		target->thread.tpidr2_el0 = tls[1];
+
 	return ret;
 }
 
@@ -714,21 +728,51 @@ static int system_call_set(struct task_struct *target,
 #ifdef CONFIG_ARM64_SVE
 
 static void sve_init_header_from_task(struct user_sve_header *header,
-				      struct task_struct *target)
+				      struct task_struct *target,
+				      enum vec_type type)
 {
 	unsigned int vq;
+	bool active;
+	bool fpsimd_only;
+	enum vec_type task_type;
 
 	memset(header, 0, sizeof(*header));
 
-	header->flags = test_tsk_thread_flag(target, TIF_SVE) ?
-		SVE_PT_REGS_SVE : SVE_PT_REGS_FPSIMD;
-	if (test_tsk_thread_flag(target, TIF_SVE_VL_INHERIT))
-		header->flags |= SVE_PT_VL_INHERIT;
+	/* Check if the requested registers are active for the task */
+	if (thread_sm_enabled(&target->thread))
+		task_type = ARM64_VEC_SME;
+	else
+		task_type = ARM64_VEC_SVE;
+	active = (task_type == type);
+
+	switch (type) {
+	case ARM64_VEC_SVE:
+		if (test_tsk_thread_flag(target, TIF_SVE_VL_INHERIT))
+			header->flags |= SVE_PT_VL_INHERIT;
+		fpsimd_only = !test_tsk_thread_flag(target, TIF_SVE);
+		break;
+	case ARM64_VEC_SME:
+		if (test_tsk_thread_flag(target, TIF_SME_VL_INHERIT))
+			header->flags |= SVE_PT_VL_INHERIT;
+		fpsimd_only = false;
+		break;
+	default:
+		WARN_ON_ONCE(1);
+		return;
+	}
+
+	if (active) {
+		if (fpsimd_only) {
+			header->flags |= SVE_PT_REGS_FPSIMD;
+		} else {
+			header->flags |= SVE_PT_REGS_SVE;
+		}
+	}
 
-	header->vl = task_get_sve_vl(target);
+	header->vl = task_get_vl(target, type);
 	vq = sve_vq_from_vl(header->vl);
 
-	header->max_vl = sve_max_vl();
+	header->max_vl = vec_max_vl(type);
 	header->size = SVE_PT_SIZE(vq, header->flags);
 	header->max_size = SVE_PT_SIZE(sve_vq_from_vl(header->max_vl),
 				      SVE_PT_REGS_SVE);
@@ -739,19 +783,17 @@ static unsigned int sve_size_from_header(struct user_sve_header const *header)
 	return ALIGN(header->size, SVE_VQ_BYTES);
 }
 
-static int sve_get(struct task_struct *target,
-		   const struct user_regset *regset,
-		   struct membuf to)
+static int sve_get_common(struct task_struct *target,
+			  const struct user_regset *regset,
+			  struct membuf to,
+			  enum vec_type type)
 {
 	struct user_sve_header header;
 	unsigned int vq;
 	unsigned long start, end;
 
-	if (!system_supports_sve())
-		return -EINVAL;
-
 	/* Header */
-	sve_init_header_from_task(&header, target);
+	sve_init_header_from_task(&header, target, type);
 	vq = sve_vq_from_vl(header.vl);
 
 	membuf_write(&to, &header, sizeof(header));
@@ -759,49 +801,61 @@ static int sve_get(struct task_struct *target,
 	if (target == current)
 		fpsimd_preserve_current_state();
 
-	/* Registers: FPSIMD-only case */
-
 	BUILD_BUG_ON(SVE_PT_FPSIMD_OFFSET != sizeof(header));
-	if ((header.flags & SVE_PT_REGS_MASK) == SVE_PT_REGS_FPSIMD)
+	BUILD_BUG_ON(SVE_PT_SVE_OFFSET != sizeof(header));
+
+	switch ((header.flags & SVE_PT_REGS_MASK)) {
+	case SVE_PT_REGS_FPSIMD:
 		return __fpr_get(target, regset, to);
 
-	/* Otherwise: full SVE case */
+	case SVE_PT_REGS_SVE:
+		start = SVE_PT_SVE_OFFSET;
+		end = SVE_PT_SVE_FFR_OFFSET(vq) + SVE_PT_SVE_FFR_SIZE(vq);
+		membuf_write(&to, target->thread.sve_state, end - start);
 
-	BUILD_BUG_ON(SVE_PT_SVE_OFFSET != sizeof(header));
-	start = SVE_PT_SVE_OFFSET;
-	end = SVE_PT_SVE_FFR_OFFSET(vq) + SVE_PT_SVE_FFR_SIZE(vq);
-	membuf_write(&to, target->thread.sve_state, end - start);
+		start = end;
+		end = SVE_PT_SVE_FPSR_OFFSET(vq);
+		membuf_zero(&to, end - start);
 
-	start = end;
-	end = SVE_PT_SVE_FPSR_OFFSET(vq);
-	membuf_zero(&to, end - start);
+		/*
+		 * Copy fpsr, and fpcr which must follow contiguously in
+		 * struct fpsimd_state:
+		 */
+		start = end;
+		end = SVE_PT_SVE_FPCR_OFFSET(vq) + SVE_PT_SVE_FPCR_SIZE;
+		membuf_write(&to, &target->thread.uw.fpsimd_state.fpsr,
+			     end - start);
 
-	/*
-	 * Copy fpsr, and fpcr which must follow contiguously in
-	 * struct fpsimd_state:
-	 */
-	start = end;
-	end = SVE_PT_SVE_FPCR_OFFSET(vq) + SVE_PT_SVE_FPCR_SIZE;
-	membuf_write(&to, &target->thread.uw.fpsimd_state.fpsr, end - start);
+		start = end;
+		end = sve_size_from_header(&header);
+		return membuf_zero(&to, end - start);
 
-	start = end;
-	end = sve_size_from_header(&header);
-	return membuf_zero(&to, end - start);
+	default:
+		return 0;
+	}
 }
 
-static int sve_set(struct task_struct *target,
+static int sve_get(struct task_struct *target,
 		   const struct user_regset *regset,
-		   unsigned int pos, unsigned int count,
-		   const void *kbuf, const void __user *ubuf)
+		   struct membuf to)
+{
+	if (!system_supports_sve())
+		return -EINVAL;
+
+	return sve_get_common(target, regset, to, ARM64_VEC_SVE);
+}
+
+static int sve_set_common(struct task_struct *target,
+			  const struct user_regset *regset,
+			  unsigned int pos, unsigned int count,
+			  const void *kbuf, const void __user *ubuf,
+			  enum vec_type type)
 {
 	int ret;
 	struct user_sve_header header;
 	unsigned int vq;
 	unsigned long start, end;
 
-	if (!system_supports_sve())
-		return -EINVAL;
-
 	/* Header */
 	if (count < sizeof(header))
 		return -EINVAL;
@@ -812,15 +866,39 @@ static int sve_set(struct task_struct *target,
 
 	/*
 	 * Apart from SVE_PT_REGS_MASK, all SVE_PT_* flags are consumed by
-	 * sve_set_vector_length(), which will also validate them for us:
+	 * vec_set_vector_length(), which will also validate them for us:
 	 */
-	ret = sve_set_vector_length(target, header.vl,
+	ret = vec_set_vector_length(target, type, header.vl,
 		((unsigned long)header.flags & ~SVE_PT_REGS_MASK) << 16);
 	if (ret)
 		goto out;
 
 	/* Actual VL set may be less than the user asked for: */
-	vq = sve_vq_from_vl(task_get_sve_vl(target));
+	vq = sve_vq_from_vl(task_get_vl(target, type));
+
+	/* Enter/exit streaming mode */
+	if (system_supports_sme()) {
+		u64 old_svcr = target->thread.svcr;
+
+		switch (type) {
+		case ARM64_VEC_SVE:
+			target->thread.svcr &= ~SVCR_SM_MASK;
+			break;
+		case ARM64_VEC_SME:
+			target->thread.svcr |= SVCR_SM_MASK;
+			break;
+		default:
+			WARN_ON_ONCE(1);
+			return -EINVAL;
+		}
+
+		/*
+		 * If we switched then invalidate any existing SVE
+		 * state and ensure there's storage.
+		 */
+		if (target->thread.svcr != old_svcr)
+			sve_alloc(target, true);
+	}
 
 	/* Registers: FPSIMD-only case */
 
@@ -829,10 +907,15 @@ static int sve_set(struct task_struct *target,
 		ret = __fpr_set(target, regset, pos, count, kbuf, ubuf,
 				SVE_PT_FPSIMD_OFFSET);
 		clear_tsk_thread_flag(target, TIF_SVE);
+		if (type == ARM64_VEC_SME)
+			fpsimd_force_sync_to_sve(target);
 		goto out;
 	}
 
-	/* Otherwise: full SVE case */
+	/*
+	 * Otherwise: no registers or full SVE case.  For backwards
+	 * compatibility reasons we treat empty flags as SVE registers.
+	 */
 
 	/*
 	 * If setting a different VL from the requested VL and there is
@@ -844,7 +927,7 @@ static int sve_set(struct task_struct *target,
 		goto out;
 	}
 
-	sve_alloc(target);
+	sve_alloc(target, true);
 	if (!target->thread.sve_state) {
 		ret = -ENOMEM;
 		clear_tsk_thread_flag(target, TIF_SVE);
@@ -853,8 +936,9 @@ static int sve_set(struct task_struct *target,
 
 	/*
 	 * Ensure target->thread.sve_state is up to date with target's
-	 * FPSIMD regs, so that a short copyin leaves trailing registers
-	 * unmodified.
+	 * FPSIMD regs, so that a short copyin leaves trailing
+	 * registers unmodified.  Always enable SVE even if going into
+	 * streaming mode.
 	 */
 	fpsimd_sync_to_sve(target);
 	set_tsk_thread_flag(target, TIF_SVE);
@@ -890,8 +974,179 @@ out:
 	return ret;
 }
 
+static int sve_set(struct task_struct *target,
+		   const struct user_regset *regset,
+		   unsigned int pos, unsigned int count,
+		   const void *kbuf, const void __user *ubuf)
+{
+	if (!system_supports_sve())
+		return -EINVAL;
+
+	return sve_set_common(target, regset, pos, count, kbuf, ubuf,
+			      ARM64_VEC_SVE);
+}
+
 #endif /* CONFIG_ARM64_SVE */
 
+#ifdef CONFIG_ARM64_SME
+
+static int ssve_get(struct task_struct *target,
+		   const struct user_regset *regset,
+		   struct membuf to)
+{
+	if (!system_supports_sme())
+		return -EINVAL;
+
+	return sve_get_common(target, regset, to, ARM64_VEC_SME);
+}
+
+static int ssve_set(struct task_struct *target,
+		    const struct user_regset *regset,
+		    unsigned int pos, unsigned int count,
+		    const void *kbuf, const void __user *ubuf)
+{
+	if (!system_supports_sme())
+		return -EINVAL;
+
+	return sve_set_common(target, regset, pos, count, kbuf, ubuf,
+			      ARM64_VEC_SME);
+}
+
+static int za_get(struct task_struct *target,
+		  const struct user_regset *regset,
+		  struct membuf to)
+{
+	struct user_za_header header;
+	unsigned int vq;
+	unsigned long start, end;
+
+	if (!system_supports_sme())
+		return -EINVAL;
+
+	/* Header */
+	memset(&header, 0, sizeof(header));
+
+	if (test_tsk_thread_flag(target, TIF_SME_VL_INHERIT))
+		header.flags |= ZA_PT_VL_INHERIT;
+
+	header.vl = task_get_sme_vl(target);
+	vq = sve_vq_from_vl(header.vl);
+	header.max_vl = sme_max_vl();
+	header.max_size = ZA_PT_SIZE(vq);
+
+	/* If ZA is not active there is only the header */
+	if (thread_za_enabled(&target->thread))
+		header.size = ZA_PT_SIZE(vq);
+	else
+		header.size = ZA_PT_ZA_OFFSET;
+
+	membuf_write(&to, &header, sizeof(header));
+
+	BUILD_BUG_ON(ZA_PT_ZA_OFFSET != sizeof(header));
+	end = ZA_PT_ZA_OFFSET;
+
+	if (target == current)
+		fpsimd_preserve_current_state();
+
+	/* Any register data to include? */
+	if (thread_za_enabled(&target->thread)) {
+		start = end;
+		end = ZA_PT_SIZE(vq);
+		membuf_write(&to, target->thread.za_state, end - start);
+	}
+
+	/* Zero any trailing padding */
+	start = end;
+	end = ALIGN(header.size, SVE_VQ_BYTES);
+	return membuf_zero(&to, end - start);
+}
+
+static int za_set(struct task_struct *target,
+		  const struct user_regset *regset,
+		  unsigned int pos, unsigned int count,
+		  const void *kbuf, const void __user *ubuf)
+{
+	int ret;
+	struct user_za_header header;
+	unsigned int vq;
+	unsigned long start, end;
+
+	if (!system_supports_sme())
+		return -EINVAL;
+
+	/* Header */
+	if (count < sizeof(header))
+		return -EINVAL;
+	ret = user_regset_copyin(&pos, &count, &kbuf, &ubuf, &header,
+				 0, sizeof(header));
+	if (ret)
+		goto out;
+
+	/*
+	 * All current ZA_PT_* flags are consumed by
+	 * vec_set_vector_length(), which will also validate them for
+	 * us:
+	 */
+	ret = vec_set_vector_length(target, ARM64_VEC_SME, header.vl,
+		((unsigned long)header.flags) << 16);
+	if (ret)
+		goto out;
+
+	/* Actual VL set may be less than the user asked for: */
+	vq = sve_vq_from_vl(task_get_sme_vl(target));
+
+	/* Ensure there is some SVE storage for streaming mode */
+	if (!target->thread.sve_state) {
+		sve_alloc(target, false);
+		if (!target->thread.sve_state) {
+			ret = -ENOMEM;
+			goto out;
+		}
+	}
+
+	/* Allocate/reinit ZA storage */
+	sme_alloc(target);
+	if (!target->thread.za_state) {
+		ret = -ENOMEM;
+		goto out;
+	}
+
+	/* If there is no data then disable ZA */
+	if (!count) {
+		target->thread.svcr &= ~SVCR_ZA_MASK;
+		goto out;
+	}
+
+	/*
+	 * If setting a different VL from the requested VL and there is
+	 * register data, the data layout will be wrong: don't even
+	 * try to set the registers in this case.
+	 */
+	if (vq != sve_vq_from_vl(header.vl)) {
+		ret = -EIO;
+		goto out;
+	}
+
+	BUILD_BUG_ON(ZA_PT_ZA_OFFSET != sizeof(header));
+	start = ZA_PT_ZA_OFFSET;
+	end = ZA_PT_SIZE(vq);
+	ret = user_regset_copyin(&pos, &count, &kbuf, &ubuf,
+				 target->thread.za_state,
+				 start, end);
+	if (ret)
+		goto out;
+
+	/* Mark ZA as active and let userspace use it */
+	set_tsk_thread_flag(target, TIF_SME);
+	target->thread.svcr |= SVCR_ZA_MASK;
+
+out:
+	fpsimd_flush_task_state(target);
+	return ret;
+}
+
+#endif /* CONFIG_ARM64_SME */
+
 #ifdef CONFIG_ARM64_PTR_AUTH
 static int pac_mask_get(struct task_struct *target,
 			const struct user_regset *regset,
@@ -1109,6 +1364,10 @@ enum aarch64_regset {
 #ifdef CONFIG_ARM64_SVE
 	REGSET_SVE,
 #endif
+#ifdef CONFIG_ARM64_SVE
+	REGSET_SSVE,
+	REGSET_ZA,
+#endif
 #ifdef CONFIG_ARM64_PTR_AUTH
 	REGSET_PAC_MASK,
 	REGSET_PAC_ENABLED_KEYS,
@@ -1146,7 +1405,7 @@ static const struct user_regset aarch64_regsets[] = {
 	},
 	[REGSET_TLS] = {
 		.core_note_type = NT_ARM_TLS,
-		.n = 1,
+		.n = 2,
 		.size = sizeof(void *),
 		.align = sizeof(void *),
 		.regset_get = tls_get,
@@ -1189,6 +1448,33 @@ static const struct user_regset aarch64_regsets[] = {
 		.set = sve_set,
 	},
 #endif
+#ifdef CONFIG_ARM64_SME
+	[REGSET_SSVE] = { /* Streaming mode SVE */
+		.core_note_type = NT_ARM_SSVE,
+		.n = DIV_ROUND_UP(SVE_PT_SIZE(SME_VQ_MAX, SVE_PT_REGS_SVE),
+				  SVE_VQ_BYTES),
+		.size = SVE_VQ_BYTES,
+		.align = SVE_VQ_BYTES,
+		.regset_get = ssve_get,
+		.set = ssve_set,
+	},
+	[REGSET_ZA] = { /* SME ZA */
+		.core_note_type = NT_ARM_ZA,
+		/*
+		 * ZA is a single register but it's variably sized and
+		 * the ptrace core requires that the size of any data
+		 * be an exact multiple of the configured register
+		 * size so report as though we had SVE_VQ_BYTES
+		 * registers. These values aren't exposed to
+		 * userspace.
+		 */
+		.n = DIV_ROUND_UP(ZA_PT_SIZE(SME_VQ_MAX), SVE_VQ_BYTES),
+		.size = SVE_VQ_BYTES,
+		.align = SVE_VQ_BYTES,
+		.regset_get = za_get,
+		.set = za_set,
+	},
+#endif
 #ifdef CONFIG_ARM64_PTR_AUTH
 	[REGSET_PAC_MASK] = {
 		.core_note_type = NT_ARM_PAC_MASK,
@@ -1792,8 +2078,7 @@ enum ptrace_syscall_dir {
 	PTRACE_SYSCALL_EXIT,
 };
 
-static void tracehook_report_syscall(struct pt_regs *regs,
-				     enum ptrace_syscall_dir dir)
+static void report_syscall(struct pt_regs *regs, enum ptrace_syscall_dir dir)
 {
 	int regno;
 	unsigned long saved_reg;
@@ -1819,11 +2104,11 @@ static void tracehook_report_syscall(struct pt_regs *regs,
 	regs->regs[regno] = dir;
 
 	if (dir == PTRACE_SYSCALL_ENTER) {
-		if (tracehook_report_syscall_entry(regs))
+		if (ptrace_report_syscall_entry(regs))
 			forget_syscall(regs);
 		regs->regs[regno] = saved_reg;
 	} else if (!test_thread_flag(TIF_SINGLESTEP)) {
-		tracehook_report_syscall_exit(regs, 0);
+		ptrace_report_syscall_exit(regs, 0);
 		regs->regs[regno] = saved_reg;
 	} else {
 		regs->regs[regno] = saved_reg;
@@ -1833,16 +2118,16 @@ static void tracehook_report_syscall(struct pt_regs *regs,
 		 * tracer modifications to the registers may have rewound the
 		 * state machine.
 		 */
-		tracehook_report_syscall_exit(regs, 1);
+		ptrace_report_syscall_exit(regs, 1);
 	}
 }
 
 int syscall_trace_enter(struct pt_regs *regs)
 {
-	unsigned long flags = READ_ONCE(current_thread_info()->flags);
+	unsigned long flags = read_thread_flags();
 
 	if (flags & (_TIF_SYSCALL_EMU | _TIF_SYSCALL_TRACE)) {
-		tracehook_report_syscall(regs, PTRACE_SYSCALL_ENTER);
+		report_syscall(regs, PTRACE_SYSCALL_ENTER);
 		if (flags & _TIF_SYSCALL_EMU)
 			return NO_SYSCALL;
 	}
@@ -1862,7 +2147,7 @@ int syscall_trace_enter(struct pt_regs *regs)
 
 void syscall_trace_exit(struct pt_regs *regs)
 {
-	unsigned long flags = READ_ONCE(current_thread_info()->flags);
+	unsigned long flags = read_thread_flags();
 
 	audit_syscall_exit(regs);
 
@@ -1870,7 +2155,7 @@ void syscall_trace_exit(struct pt_regs *regs)
 		trace_sys_exit(regs, syscall_get_return_value(current, regs));
 
 	if (flags & (_TIF_SYSCALL_TRACE | _TIF_SINGLESTEP))
-		tracehook_report_syscall(regs, PTRACE_SYSCALL_EXIT);
+		report_syscall(regs, PTRACE_SYSCALL_EXIT);
 
 	rseq_syscall(regs);
 }
diff --git a/arch/arm64/kernel/reloc_test_core.c b/arch/arm64/kernel/reloc_test_core.c
index e87a2b7f20f6..99f2ffe9fc05 100644
--- a/arch/arm64/kernel/reloc_test_core.c
+++ b/arch/arm64/kernel/reloc_test_core.c
@@ -48,7 +48,7 @@ static struct {
 	{ "R_AARCH64_PREL16",		relative_data16, (u64)&sym64_rel },
 };
 
-static int reloc_test_init(void)
+static int __init reloc_test_init(void)
 {
 	int i;
 
@@ -67,7 +67,7 @@ static int reloc_test_init(void)
 	return 0;
 }
 
-static void reloc_test_exit(void)
+static void __exit reloc_test_exit(void)
 {
 }
 
diff --git a/arch/arm64/kernel/relocate_kernel.S b/arch/arm64/kernel/relocate_kernel.S
index f0a3df9e18a3..413f899e4ac6 100644
--- a/arch/arm64/kernel/relocate_kernel.S
+++ b/arch/arm64/kernel/relocate_kernel.S
@@ -37,6 +37,15 @@
  * safe memory that has been set up to be preserved during the copy operation.
  */
 SYM_CODE_START(arm64_relocate_new_kernel)
+	/*
+	 * The kimage structure isn't allocated specially and may be clobbered
+	 * during relocation. We must load any values we need from it prior to
+	 * any relocation occurring.
+	 */
+	ldr	x28, [x0, #KIMAGE_START]
+	ldr	x27, [x0, #KIMAGE_ARCH_EL2_VECTORS]
+	ldr	x26, [x0, #KIMAGE_ARCH_DTB_MEM]
+
 	/* Setup the list loop variables. */
 	ldr	x18, [x0, #KIMAGE_ARCH_ZERO_PAGE] /* x18 = zero page for BBM */
 	ldr	x17, [x0, #KIMAGE_ARCH_TTBR1]	/* x17 = linear map copy */
@@ -72,21 +81,20 @@ SYM_CODE_START(arm64_relocate_new_kernel)
 	ic	iallu
 	dsb	nsh
 	isb
-	ldr	x4, [x0, #KIMAGE_START]			/* relocation start */
-	ldr	x1, [x0, #KIMAGE_ARCH_EL2_VECTORS]	/* relocation start */
-	ldr	x0, [x0, #KIMAGE_ARCH_DTB_MEM]		/* dtb address */
 	turn_off_mmu x12, x13
 
 	/* Start new image. */
-	cbz	x1, .Lel1
-	mov	x1, x4				/* relocation start */
-	mov	x2, x0				/* dtb address */
+	cbz	x27, .Lel1
+	mov	x1, x28				/* kernel entry point */
+	mov	x2, x26				/* dtb address */
 	mov	x3, xzr
 	mov	x4, xzr
 	mov     x0, #HVC_SOFT_RESTART
 	hvc	#0				/* Jumps from el2 */
 .Lel1:
+	mov	x0, x26				/* dtb address */
+	mov	x1, xzr
 	mov	x2, xzr
 	mov	x3, xzr
-	br	x4				/* Jumps from el1 */
+	br	x28				/* Jumps from el1 */
 SYM_CODE_END(arm64_relocate_new_kernel)
diff --git a/arch/arm64/kernel/return_address.c b/arch/arm64/kernel/return_address.c
index a6d18755652f..68330017d04f 100644
--- a/arch/arm64/kernel/return_address.c
+++ b/arch/arm64/kernel/return_address.c
@@ -9,9 +9,9 @@
 #include <linux/export.h>
 #include <linux/ftrace.h>
 #include <linux/kprobes.h>
+#include <linux/stacktrace.h>
 
 #include <asm/stack_pointer.h>
-#include <asm/stacktrace.h>
 
 struct return_address_data {
 	unsigned int level;
@@ -35,15 +35,11 @@ NOKPROBE_SYMBOL(save_return_addr);
 void *return_address(unsigned int level)
 {
 	struct return_address_data data;
-	struct stackframe frame;
 
 	data.level = level + 2;
 	data.addr = NULL;
 
-	start_backtrace(&frame,
-			(unsigned long)__builtin_frame_address(0),
-			(unsigned long)return_address);
-	walk_stackframe(current, &frame, save_return_addr, &data);
+	arch_stack_walk(save_return_addr, &data, current, NULL);
 
 	if (!data.level)
 		return data.addr;
diff --git a/arch/arm64/kernel/sdei.c b/arch/arm64/kernel/sdei.c
index d20620a1c51a..d56e170e1ca7 100644
--- a/arch/arm64/kernel/sdei.c
+++ b/arch/arm64/kernel/sdei.c
@@ -162,38 +162,6 @@ static int init_sdei_scs(void)
 	return err;
 }
 
-static bool on_sdei_normal_stack(unsigned long sp, unsigned long size,
-				 struct stack_info *info)
-{
-	unsigned long low = (unsigned long)raw_cpu_read(sdei_stack_normal_ptr);
-	unsigned long high = low + SDEI_STACK_SIZE;
-
-	return on_stack(sp, size, low, high, STACK_TYPE_SDEI_NORMAL, info);
-}
-
-static bool on_sdei_critical_stack(unsigned long sp, unsigned long size,
-				   struct stack_info *info)
-{
-	unsigned long low = (unsigned long)raw_cpu_read(sdei_stack_critical_ptr);
-	unsigned long high = low + SDEI_STACK_SIZE;
-
-	return on_stack(sp, size, low, high, STACK_TYPE_SDEI_CRITICAL, info);
-}
-
-bool _on_sdei_stack(unsigned long sp, unsigned long size, struct stack_info *info)
-{
-	if (!IS_ENABLED(CONFIG_VMAP_STACK))
-		return false;
-
-	if (on_sdei_critical_stack(sp, size, info))
-		return true;
-
-	if (on_sdei_normal_stack(sp, size, info))
-		return true;
-
-	return false;
-}
-
 unsigned long sdei_arch_get_entry_point(int conduit)
 {
 	/*
diff --git a/arch/arm64/kernel/setup.c b/arch/arm64/kernel/setup.c
index be5f85b0a24d..fea3223704b6 100644
--- a/arch/arm64/kernel/setup.c
+++ b/arch/arm64/kernel/setup.c
@@ -189,11 +189,16 @@ static void __init setup_machine_fdt(phys_addr_t dt_phys)
 
 	if (!dt_virt || !early_init_dt_scan(dt_virt)) {
 		pr_crit("\n"
-			"Error: invalid device tree blob at physical address %pa (virtual address 0x%p)\n"
+			"Error: invalid device tree blob at physical address %pa (virtual address 0x%px)\n"
 			"The dtb must be 8-byte aligned and must not exceed 2 MB in size\n"
 			"\nPlease check your bootloader.",
 			&dt_phys, dt_virt);
 
+		/*
+		 * Note that in this _really_ early stage we cannot even BUG()
+		 * or oops, so the least terrible thing to do is cpu_relax(),
+		 * or else we could end-up printing non-initialized data, etc.
+		 */
 		while (true)
 			cpu_relax();
 	}
@@ -220,6 +225,8 @@ static void __init request_standard_resources(void)
 	kernel_code.end     = __pa_symbol(__init_begin - 1);
 	kernel_data.start   = __pa_symbol(_sdata);
 	kernel_data.end     = __pa_symbol(_end - 1);
+	insert_resource(&iomem_resource, &kernel_code);
+	insert_resource(&iomem_resource, &kernel_data);
 
 	num_standard_resources = memblock.memory.cnt;
 	res_size = num_standard_resources * sizeof(*standard_resources);
@@ -232,27 +239,16 @@ static void __init request_standard_resources(void)
 		if (memblock_is_nomap(region)) {
 			res->name  = "reserved";
 			res->flags = IORESOURCE_MEM;
+			res->start = __pfn_to_phys(memblock_region_reserved_base_pfn(region));
+			res->end = __pfn_to_phys(memblock_region_reserved_end_pfn(region)) - 1;
 		} else {
 			res->name  = "System RAM";
 			res->flags = IORESOURCE_SYSTEM_RAM | IORESOURCE_BUSY;
+			res->start = __pfn_to_phys(memblock_region_memory_base_pfn(region));
+			res->end = __pfn_to_phys(memblock_region_memory_end_pfn(region)) - 1;
 		}
-		res->start = __pfn_to_phys(memblock_region_memory_base_pfn(region));
-		res->end = __pfn_to_phys(memblock_region_memory_end_pfn(region)) - 1;
-
-		request_resource(&iomem_resource, res);
-
-		if (kernel_code.start >= res->start &&
-		    kernel_code.end <= res->end)
-			request_resource(res, &kernel_code);
-		if (kernel_data.start >= res->start &&
-		    kernel_data.end <= res->end)
-			request_resource(res, &kernel_data);
-#ifdef CONFIG_KEXEC_CORE
-		/* Userspace will find "Crash kernel" region in /proc/iomem. */
-		if (crashk_res.end && crashk_res.start >= res->start &&
-		    crashk_res.end <= res->end)
-			request_resource(res, &crashk_res);
-#endif
+
+		insert_resource(&iomem_resource, res);
 	}
 }
 
@@ -399,9 +395,6 @@ static int __init topology_init(void)
 {
 	int i;
 
-	for_each_online_node(i)
-		register_one_node(i);
-
 	for_each_possible_cpu(i) {
 		struct cpu *cpu = &per_cpu(cpu_data.cpu, i);
 		cpu->hotpluggable = cpu_can_disable(i);
diff --git a/arch/arm64/kernel/signal.c b/arch/arm64/kernel/signal.c
index 8f6372b44b65..9ad911f1647c 100644
--- a/arch/arm64/kernel/signal.c
+++ b/arch/arm64/kernel/signal.c
@@ -11,13 +11,12 @@
 #include <linux/errno.h>
 #include <linux/kernel.h>
 #include <linux/signal.h>
-#include <linux/personality.h>
 #include <linux/freezer.h>
 #include <linux/stddef.h>
 #include <linux/uaccess.h>
 #include <linux/sizes.h>
 #include <linux/string.h>
-#include <linux/tracehook.h>
+#include <linux/resume_user_mode.h>
 #include <linux/ratelimit.h>
 #include <linux/syscalls.h>
 
@@ -57,6 +56,7 @@ struct rt_sigframe_user_layout {
 	unsigned long fpsimd_offset;
 	unsigned long esr_offset;
 	unsigned long sve_offset;
+	unsigned long za_offset;
 	unsigned long extra_offset;
 	unsigned long end_offset;
 };
@@ -91,7 +91,7 @@ static size_t sigframe_size(struct rt_sigframe_user_layout const *user)
  * not taken into account.  This limit is not a guarantee and is
  * NOT ABI.
  */
-#define SIGFRAME_MAXSZ SZ_64K
+#define SIGFRAME_MAXSZ SZ_256K
 
 static int __sigframe_alloc(struct rt_sigframe_user_layout *user,
 			    unsigned long *offset, size_t size, bool extend)
@@ -219,6 +219,7 @@ static int restore_fpsimd_context(struct fpsimd_context __user *ctx)
 struct user_ctxs {
 	struct fpsimd_context __user *fpsimd;
 	struct sve_context __user *sve;
+	struct za_context __user *za;
 };
 
 #ifdef CONFIG_ARM64_SVE
@@ -227,11 +228,17 @@ static int preserve_sve_context(struct sve_context __user *ctx)
 {
 	int err = 0;
 	u16 reserved[ARRAY_SIZE(ctx->__reserved)];
+	u16 flags = 0;
 	unsigned int vl = task_get_sve_vl(current);
 	unsigned int vq = 0;
 
-	if (test_thread_flag(TIF_SVE))
+	if (thread_sm_enabled(&current->thread)) {
+		vl = task_get_sme_vl(current);
 		vq = sve_vq_from_vl(vl);
+		flags |= SVE_SIG_FLAG_SM;
+	} else if (test_thread_flag(TIF_SVE)) {
+		vq = sve_vq_from_vl(vl);
+	}
 
 	memset(reserved, 0, sizeof(reserved));
 
@@ -239,6 +246,7 @@ static int preserve_sve_context(struct sve_context __user *ctx)
 	__put_user_error(round_up(SVE_SIG_CONTEXT_SIZE(vq), 16),
 			 &ctx->head.size, err);
 	__put_user_error(vl, &ctx->vl, err);
+	__put_user_error(flags, &ctx->flags, err);
 	BUILD_BUG_ON(sizeof(ctx->__reserved) != sizeof(reserved));
 	err |= __copy_to_user(&ctx->__reserved, reserved, sizeof(reserved));
 
@@ -259,18 +267,31 @@ static int preserve_sve_context(struct sve_context __user *ctx)
 static int restore_sve_fpsimd_context(struct user_ctxs *user)
 {
 	int err;
-	unsigned int vq;
+	unsigned int vl, vq;
 	struct user_fpsimd_state fpsimd;
 	struct sve_context sve;
 
 	if (__copy_from_user(&sve, user->sve, sizeof(sve)))
 		return -EFAULT;
 
-	if (sve.vl != task_get_sve_vl(current))
+	if (sve.flags & SVE_SIG_FLAG_SM) {
+		if (!system_supports_sme())
+			return -EINVAL;
+
+		vl = task_get_sme_vl(current);
+	} else {
+		if (!system_supports_sve())
+			return -EINVAL;
+
+		vl = task_get_sve_vl(current);
+	}
+
+	if (sve.vl != vl)
 		return -EINVAL;
 
 	if (sve.head.size <= sizeof(*user->sve)) {
 		clear_thread_flag(TIF_SVE);
+		current->thread.svcr &= ~SVCR_SM_MASK;
 		goto fpsimd_only;
 	}
 
@@ -289,7 +310,7 @@ static int restore_sve_fpsimd_context(struct user_ctxs *user)
 	fpsimd_flush_task_state(current);
 	/* From now, fpsimd_thread_switch() won't touch thread.sve_state */
 
-	sve_alloc(current);
+	sve_alloc(current, true);
 	if (!current->thread.sve_state) {
 		clear_thread_flag(TIF_SVE);
 		return -ENOMEM;
@@ -302,7 +323,10 @@ static int restore_sve_fpsimd_context(struct user_ctxs *user)
 	if (err)
 		return -EFAULT;
 
-	set_thread_flag(TIF_SVE);
+	if (sve.flags & SVE_SIG_FLAG_SM)
+		current->thread.svcr |= SVCR_SM_MASK;
+	else
+		set_thread_flag(TIF_SVE);
 
 fpsimd_only:
 	/* copy the FP and status/control registers */
@@ -321,12 +345,112 @@ fpsimd_only:
 
 #else /* ! CONFIG_ARM64_SVE */
 
-/* Turn any non-optimised out attempts to use these into a link error: */
+static int restore_sve_fpsimd_context(struct user_ctxs *user)
+{
+	WARN_ON_ONCE(1);
+	return -EINVAL;
+}
+
+/* Turn any non-optimised out attempts to use this into a link error: */
 extern int preserve_sve_context(void __user *ctx);
-extern int restore_sve_fpsimd_context(struct user_ctxs *user);
 
 #endif /* ! CONFIG_ARM64_SVE */
 
+#ifdef CONFIG_ARM64_SME
+
+static int preserve_za_context(struct za_context __user *ctx)
+{
+	int err = 0;
+	u16 reserved[ARRAY_SIZE(ctx->__reserved)];
+	unsigned int vl = task_get_sme_vl(current);
+	unsigned int vq;
+
+	if (thread_za_enabled(&current->thread))
+		vq = sve_vq_from_vl(vl);
+	else
+		vq = 0;
+
+	memset(reserved, 0, sizeof(reserved));
+
+	__put_user_error(ZA_MAGIC, &ctx->head.magic, err);
+	__put_user_error(round_up(ZA_SIG_CONTEXT_SIZE(vq), 16),
+			 &ctx->head.size, err);
+	__put_user_error(vl, &ctx->vl, err);
+	BUILD_BUG_ON(sizeof(ctx->__reserved) != sizeof(reserved));
+	err |= __copy_to_user(&ctx->__reserved, reserved, sizeof(reserved));
+
+	if (vq) {
+		/*
+		 * This assumes that the ZA state has already been saved to
+		 * the task struct by calling the function
+		 * fpsimd_signal_preserve_current_state().
+		 */
+		err |= __copy_to_user((char __user *)ctx + ZA_SIG_REGS_OFFSET,
+				      current->thread.za_state,
+				      ZA_SIG_REGS_SIZE(vq));
+	}
+
+	return err ? -EFAULT : 0;
+}
+
+static int restore_za_context(struct user_ctxs *user)
+{
+	int err;
+	unsigned int vq;
+	struct za_context za;
+
+	if (__copy_from_user(&za, user->za, sizeof(za)))
+		return -EFAULT;
+
+	if (za.vl != task_get_sme_vl(current))
+		return -EINVAL;
+
+	if (za.head.size <= sizeof(*user->za)) {
+		current->thread.svcr &= ~SVCR_ZA_MASK;
+		return 0;
+	}
+
+	vq = sve_vq_from_vl(za.vl);
+
+	if (za.head.size < ZA_SIG_CONTEXT_SIZE(vq))
+		return -EINVAL;
+
+	/*
+	 * Careful: we are about __copy_from_user() directly into
+	 * thread.za_state with preemption enabled, so protection is
+	 * needed to prevent a racing context switch from writing stale
+	 * registers back over the new data.
+	 */
+
+	fpsimd_flush_task_state(current);
+	/* From now, fpsimd_thread_switch() won't touch thread.sve_state */
+
+	sme_alloc(current);
+	if (!current->thread.za_state) {
+		current->thread.svcr &= ~SVCR_ZA_MASK;
+		clear_thread_flag(TIF_SME);
+		return -ENOMEM;
+	}
+
+	err = __copy_from_user(current->thread.za_state,
+			       (char __user const *)user->za +
+					ZA_SIG_REGS_OFFSET,
+			       ZA_SIG_REGS_SIZE(vq));
+	if (err)
+		return -EFAULT;
+
+	set_thread_flag(TIF_SME);
+	current->thread.svcr |= SVCR_ZA_MASK;
+
+	return 0;
+}
+#else /* ! CONFIG_ARM64_SME */
+
+/* Turn any non-optimised out attempts to use these into a link error: */
+extern int preserve_za_context(void __user *ctx);
+extern int restore_za_context(struct user_ctxs *user);
+
+#endif /* ! CONFIG_ARM64_SME */
 
 static int parse_user_sigframe(struct user_ctxs *user,
 			       struct rt_sigframe __user *sf)
@@ -341,6 +465,7 @@ static int parse_user_sigframe(struct user_ctxs *user,
 
 	user->fpsimd = NULL;
 	user->sve = NULL;
+	user->za = NULL;
 
 	if (!IS_ALIGNED((unsigned long)base, 16))
 		goto invalid;
@@ -394,7 +519,7 @@ static int parse_user_sigframe(struct user_ctxs *user,
 			break;
 
 		case SVE_MAGIC:
-			if (!system_supports_sve())
+			if (!system_supports_sve() && !system_supports_sme())
 				goto invalid;
 
 			if (user->sve)
@@ -406,6 +531,19 @@ static int parse_user_sigframe(struct user_ctxs *user,
 			user->sve = (struct sve_context __user *)head;
 			break;
 
+		case ZA_MAGIC:
+			if (!system_supports_sme())
+				goto invalid;
+
+			if (user->za)
+				goto invalid;
+
+			if (size < sizeof(*user->za))
+				goto invalid;
+
+			user->za = (struct za_context __user *)head;
+			break;
+
 		case EXTRA_MAGIC:
 			if (have_extra_context)
 				goto invalid;
@@ -519,16 +657,15 @@ static int restore_sigframe(struct pt_regs *regs,
 		if (!user.fpsimd)
 			return -EINVAL;
 
-		if (user.sve) {
-			if (!system_supports_sve())
-				return -EINVAL;
-
+		if (user.sve)
 			err = restore_sve_fpsimd_context(&user);
-		} else {
+		else
 			err = restore_fpsimd_context(user.fpsimd);
-		}
 	}
 
+	if (err == 0 && system_supports_sme() && user.za)
+		err = restore_za_context(&user);
+
 	return err;
 }
 
@@ -577,10 +714,12 @@ static int setup_sigframe_layout(struct rt_sigframe_user_layout *user,
 {
 	int err;
 
-	err = sigframe_alloc(user, &user->fpsimd_offset,
-			     sizeof(struct fpsimd_context));
-	if (err)
-		return err;
+	if (system_supports_fpsimd()) {
+		err = sigframe_alloc(user, &user->fpsimd_offset,
+				     sizeof(struct fpsimd_context));
+		if (err)
+			return err;
+	}
 
 	/* fault information, if valid */
 	if (add_all || current->thread.fault_code) {
@@ -593,11 +732,12 @@ static int setup_sigframe_layout(struct rt_sigframe_user_layout *user,
 	if (system_supports_sve()) {
 		unsigned int vq = 0;
 
-		if (add_all || test_thread_flag(TIF_SVE)) {
-			int vl = sve_max_vl();
+		if (add_all || test_thread_flag(TIF_SVE) ||
+		    thread_sm_enabled(&current->thread)) {
+			int vl = max(sve_max_vl(), sme_max_vl());
 
 			if (!add_all)
-				vl = task_get_sve_vl(current);
+				vl = thread_get_cur_vl(&current->thread);
 
 			vq = sve_vq_from_vl(vl);
 		}
@@ -608,6 +748,24 @@ static int setup_sigframe_layout(struct rt_sigframe_user_layout *user,
 			return err;
 	}
 
+	if (system_supports_sme()) {
+		unsigned int vl;
+		unsigned int vq = 0;
+
+		if (add_all)
+			vl = sme_max_vl();
+		else
+			vl = task_get_sme_vl(current);
+
+		if (thread_za_enabled(&current->thread))
+			vq = sve_vq_from_vl(vl);
+
+		err = sigframe_alloc(user, &user->za_offset,
+				     ZA_SIG_CONTEXT_SIZE(vq));
+		if (err)
+			return err;
+	}
+
 	return sigframe_alloc_end(user);
 }
 
@@ -648,13 +806,21 @@ static int setup_sigframe(struct rt_sigframe_user_layout *user,
 		__put_user_error(current->thread.fault_code, &esr_ctx->esr, err);
 	}
 
-	/* Scalable Vector Extension state, if present */
-	if (system_supports_sve() && err == 0 && user->sve_offset) {
+	/* Scalable Vector Extension state (including streaming), if present */
+	if ((system_supports_sve() || system_supports_sme()) &&
+	    err == 0 && user->sve_offset) {
 		struct sve_context __user *sve_ctx =
 			apply_user_offset(user, user->sve_offset);
 		err |= preserve_sve_context(sve_ctx);
 	}
 
+	/* ZA state if present */
+	if (system_supports_sme() && err == 0 && user->za_offset) {
+		struct za_context __user *za_ctx =
+			apply_user_offset(user, user->za_offset);
+		err |= preserve_za_context(za_ctx);
+	}
+
 	if (err == 0 && user->extra_offset) {
 		char __user *sfp = (char __user *)user->sigframe;
 		char __user *userp =
@@ -758,6 +924,23 @@ static void setup_return(struct pt_regs *regs, struct k_sigaction *ka,
 	/* TCO (Tag Check Override) always cleared for signal handlers */
 	regs->pstate &= ~PSR_TCO_BIT;
 
+	/* Signal handlers are invoked with ZA and streaming mode disabled */
+	if (system_supports_sme()) {
+		/*
+		 * If we were in streaming mode the saved register
+		 * state was SVE but we will exit SM and use the
+		 * FPSIMD register state - flush the saved FPSIMD
+		 * register state in case it gets loaded.
+		 */
+		if (current->thread.svcr & SVCR_SM_MASK)
+			memset(&current->thread.uw.fpsimd_state, 0,
+			       sizeof(current->thread.uw.fpsimd_state));
+
+		current->thread.svcr &= ~(SVCR_ZA_MASK |
+					  SVCR_SM_MASK);
+		sme_smstop();
+	}
+
 	if (ka->sa.sa_flags & SA_RESTORER)
 		sigtramp = ka->sa.sa_restorer;
 	else
@@ -941,14 +1124,14 @@ void do_notify_resume(struct pt_regs *regs, unsigned long thread_flags)
 				do_signal(regs);
 
 			if (thread_flags & _TIF_NOTIFY_RESUME)
-				tracehook_notify_resume(regs);
+				resume_user_mode_work(regs);
 
 			if (thread_flags & _TIF_FOREIGN_FPSTATE)
 				fpsimd_restore_current_state();
 		}
 
 		local_daif_mask();
-		thread_flags = READ_ONCE(current_thread_info()->flags);
+		thread_flags = read_thread_flags();
 	} while (thread_flags & _TIF_WORK_MASK);
 }
 
@@ -1010,6 +1193,7 @@ static_assert(offsetof(siginfo_t, si_upper)	== 0x28);
 static_assert(offsetof(siginfo_t, si_pkey)	== 0x20);
 static_assert(offsetof(siginfo_t, si_perf_data)	== 0x18);
 static_assert(offsetof(siginfo_t, si_perf_type)	== 0x20);
+static_assert(offsetof(siginfo_t, si_perf_flags) == 0x24);
 static_assert(offsetof(siginfo_t, si_band)	== 0x10);
 static_assert(offsetof(siginfo_t, si_fd)	== 0x18);
 static_assert(offsetof(siginfo_t, si_call_addr)	== 0x10);
diff --git a/arch/arm64/kernel/signal32.c b/arch/arm64/kernel/signal32.c
index d984282b979f..4700f8522d27 100644
--- a/arch/arm64/kernel/signal32.c
+++ b/arch/arm64/kernel/signal32.c
@@ -487,6 +487,7 @@ static_assert(offsetof(compat_siginfo_t, si_upper)	== 0x18);
 static_assert(offsetof(compat_siginfo_t, si_pkey)	== 0x14);
 static_assert(offsetof(compat_siginfo_t, si_perf_data)	== 0x10);
 static_assert(offsetof(compat_siginfo_t, si_perf_type)	== 0x14);
+static_assert(offsetof(compat_siginfo_t, si_perf_flags)	== 0x18);
 static_assert(offsetof(compat_siginfo_t, si_band)	== 0x0c);
 static_assert(offsetof(compat_siginfo_t, si_fd)		== 0x10);
 static_assert(offsetof(compat_siginfo_t, si_call_addr)	== 0x0c);
diff --git a/arch/arm64/kernel/sigreturn32.S b/arch/arm64/kernel/sigreturn32.S
index 475d30d471ac..ccbd4aab4ba4 100644
--- a/arch/arm64/kernel/sigreturn32.S
+++ b/arch/arm64/kernel/sigreturn32.S
@@ -15,6 +15,7 @@
 
 #include <asm/unistd.h>
 
+	.section .rodata
 	.globl __aarch32_sigret_code_start
 __aarch32_sigret_code_start:
 
diff --git a/arch/arm64/kernel/sleep.S b/arch/arm64/kernel/sleep.S
index 4ea9392f86e0..97c9de57725d 100644
--- a/arch/arm64/kernel/sleep.S
+++ b/arch/arm64/kernel/sleep.S
@@ -100,10 +100,14 @@ SYM_FUNC_END(__cpu_suspend_enter)
 	.pushsection ".idmap.text", "awx"
 SYM_CODE_START(cpu_resume)
 	bl	init_kernel_el
-	bl	switch_to_vhe
+	bl	finalise_el2
+#if VA_BITS > 48
+	ldr_l	x0, vabits_actual
+#endif
 	bl	__cpu_setup
 	/* enable the MMU early - so we can access sleep_save_stash by va */
 	adrp	x1, swapper_pg_dir
+	adrp	x2, idmap_pg_dir
 	bl	__enable_mmu
 	ldr	x8, =_cpu_resume
 	br	x8
diff --git a/arch/arm64/kernel/smp.c b/arch/arm64/kernel/smp.c
index 27df5c1e6baa..ffc5d76cf695 100644
--- a/arch/arm64/kernel/smp.c
+++ b/arch/arm64/kernel/smp.c
@@ -234,6 +234,7 @@ asmlinkage notrace void secondary_start_kernel(void)
 	 * Log the CPU info before it is marked online and might get read.
 	 */
 	cpuinfo_store_cpu();
+	store_cpu_topology(cpu);
 
 	/*
 	 * Enable GIC and timers.
@@ -242,7 +243,6 @@ asmlinkage notrace void secondary_start_kernel(void)
 
 	ipi_setup(cpu);
 
-	store_cpu_topology(cpu);
 	numa_add_cpu(cpu);
 
 	/*
@@ -512,6 +512,7 @@ struct acpi_madt_generic_interrupt *acpi_cpu_get_madt_gicc(int cpu)
 {
 	return &cpu_madt_gicc[cpu];
 }
+EXPORT_SYMBOL_GPL(acpi_cpu_get_madt_gicc);
 
 /*
  * acpi_map_gic_cpu_interface - parse processor MADT entry
@@ -1077,14 +1078,6 @@ bool smp_crash_stop_failed(void)
 }
 #endif
 
-/*
- * not supported here
- */
-int setup_profiling_timer(unsigned int multiplier)
-{
-	return -EINVAL;
-}
-
 static bool have_cpu_die(void)
 {
 #ifdef CONFIG_HOTPLUG_CPU
diff --git a/arch/arm64/kernel/smp_spin_table.c b/arch/arm64/kernel/smp_spin_table.c
index 7e1624ecab3c..49029eace3ad 100644
--- a/arch/arm64/kernel/smp_spin_table.c
+++ b/arch/arm64/kernel/smp_spin_table.c
@@ -66,7 +66,7 @@ static int smp_spin_table_cpu_init(unsigned int cpu)
 static int smp_spin_table_cpu_prepare(unsigned int cpu)
 {
 	__le64 __iomem *release_addr;
-	phys_addr_t pa_holding_pen = __pa_symbol(function_nocfi(secondary_holding_pen));
+	phys_addr_t pa_holding_pen = __pa_symbol(secondary_holding_pen);
 
 	if (!cpu_release_addr[cpu])
 		return -ENODEV;
diff --git a/arch/arm64/kernel/stacktrace.c b/arch/arm64/kernel/stacktrace.c
index 94f83cd44e50..634279b3b03d 100644
--- a/arch/arm64/kernel/stacktrace.c
+++ b/arch/arm64/kernel/stacktrace.c
@@ -7,53 +7,64 @@
 #include <linux/kernel.h>
 #include <linux/export.h>
 #include <linux/ftrace.h>
-#include <linux/kprobes.h>
 #include <linux/sched.h>
 #include <linux/sched/debug.h>
 #include <linux/sched/task_stack.h>
 #include <linux/stacktrace.h>
 
 #include <asm/irq.h>
-#include <asm/pointer_auth.h>
 #include <asm/stack_pointer.h>
 #include <asm/stacktrace.h>
 
 /*
- * AArch64 PCS assigns the frame pointer to x29.
+ * Start an unwind from a pt_regs.
  *
- * A simple function prologue looks like this:
- * 	sub	sp, sp, #0x10
- *   	stp	x29, x30, [sp]
- *	mov	x29, sp
+ * The unwind will begin at the PC within the regs.
  *
- * A simple function epilogue looks like this:
- *	mov	sp, x29
- *	ldp	x29, x30, [sp]
- *	add	sp, sp, #0x10
+ * The regs must be on a stack currently owned by the calling task.
  */
+static inline void unwind_init_from_regs(struct unwind_state *state,
+					 struct pt_regs *regs)
+{
+	unwind_init_common(state, current);
 
+	state->fp = regs->regs[29];
+	state->pc = regs->pc;
+}
 
-void start_backtrace(struct stackframe *frame, unsigned long fp,
-		     unsigned long pc)
+/*
+ * Start an unwind from a caller.
+ *
+ * The unwind will begin at the caller of whichever function this is inlined
+ * into.
+ *
+ * The function which invokes this must be noinline.
+ */
+static __always_inline void unwind_init_from_caller(struct unwind_state *state)
 {
-	frame->fp = fp;
-	frame->pc = pc;
-#ifdef CONFIG_KRETPROBES
-	frame->kr_cur = NULL;
-#endif
+	unwind_init_common(state, current);
+
+	state->fp = (unsigned long)__builtin_frame_address(1);
+	state->pc = (unsigned long)__builtin_return_address(0);
+}
+
+/*
+ * Start an unwind from a blocked task.
+ *
+ * The unwind will begin at the blocked tasks saved PC (i.e. the caller of
+ * cpu_switch_to()).
+ *
+ * The caller should ensure the task is blocked in cpu_switch_to() for the
+ * duration of the unwind, or the unwind will be bogus. It is never valid to
+ * call this for the current task.
+ */
+static inline void unwind_init_from_task(struct unwind_state *state,
+					 struct task_struct *task)
+{
+	unwind_init_common(state, task);
 
-	/*
-	 * Prime the first unwind.
-	 *
-	 * In unwind_frame() we'll check that the FP points to a valid stack,
-	 * which can't be STACK_TYPE_UNKNOWN, and the first unwind will be
-	 * treated as a transition to whichever stack that happens to be. The
-	 * prev_fp value won't be used, but we set it to 0 such that it is
-	 * definitely not an accessible stack address.
-	 */
-	bitmap_zero(frame->stacks_done, __NR_STACK_TYPES);
-	frame->prev_fp = 0;
-	frame->prev_type = STACK_TYPE_UNKNOWN;
+	state->fp = thread_saved_fp(task);
+	state->pc = thread_saved_pc(task);
 }
 
 /*
@@ -63,61 +74,25 @@ void start_backtrace(struct stackframe *frame, unsigned long fp,
  * records (e.g. a cycle), determined based on the location and fp value of A
  * and the location (but not the fp value) of B.
  */
-int notrace unwind_frame(struct task_struct *tsk, struct stackframe *frame)
+static int notrace unwind_next(struct unwind_state *state)
 {
-	unsigned long fp = frame->fp;
-	struct stack_info info;
-
-	if (!tsk)
-		tsk = current;
+	struct task_struct *tsk = state->task;
+	unsigned long fp = state->fp;
+	int err;
 
 	/* Final frame; nothing to unwind */
 	if (fp == (unsigned long)task_pt_regs(tsk)->stackframe)
 		return -ENOENT;
 
-	if (fp & 0x7)
-		return -EINVAL;
-
-	if (!on_accessible_stack(tsk, fp, 16, &info))
-		return -EINVAL;
-
-	if (test_bit(info.type, frame->stacks_done))
-		return -EINVAL;
-
-	/*
-	 * As stacks grow downward, any valid record on the same stack must be
-	 * at a strictly higher address than the prior record.
-	 *
-	 * Stacks can nest in several valid orders, e.g.
-	 *
-	 * TASK -> IRQ -> OVERFLOW -> SDEI_NORMAL
-	 * TASK -> SDEI_NORMAL -> SDEI_CRITICAL -> OVERFLOW
-	 *
-	 * ... but the nesting itself is strict. Once we transition from one
-	 * stack to another, it's never valid to unwind back to that first
-	 * stack.
-	 */
-	if (info.type == frame->prev_type) {
-		if (fp <= frame->prev_fp)
-			return -EINVAL;
-	} else {
-		set_bit(frame->prev_type, frame->stacks_done);
-	}
-
-	/*
-	 * Record this frame record's values and location. The prev_fp and
-	 * prev_type are only meaningful to the next unwind_frame() invocation.
-	 */
-	frame->fp = READ_ONCE_NOCHECK(*(unsigned long *)(fp));
-	frame->pc = READ_ONCE_NOCHECK(*(unsigned long *)(fp + 8));
-	frame->prev_fp = fp;
-	frame->prev_type = info.type;
+	err = unwind_next_frame_record(state);
+	if (err)
+		return err;
 
-	frame->pc = ptrauth_strip_insn_pac(frame->pc);
+	state->pc = ptrauth_strip_insn_pac(state->pc);
 
 #ifdef CONFIG_FUNCTION_GRAPH_TRACER
 	if (tsk->ret_stack &&
-		(frame->pc == (unsigned long)return_to_handler)) {
+		(state->pc == (unsigned long)return_to_handler)) {
 		unsigned long orig_pc;
 		/*
 		 * This is a case where function graph tracer has
@@ -125,55 +100,51 @@ int notrace unwind_frame(struct task_struct *tsk, struct stackframe *frame)
 		 * to hook a function return.
 		 * So replace it to an original value.
 		 */
-		orig_pc = ftrace_graph_ret_addr(tsk, NULL, frame->pc,
-						(void *)frame->fp);
-		if (WARN_ON_ONCE(frame->pc == orig_pc))
+		orig_pc = ftrace_graph_ret_addr(tsk, NULL, state->pc,
+						(void *)state->fp);
+		if (WARN_ON_ONCE(state->pc == orig_pc))
 			return -EINVAL;
-		frame->pc = orig_pc;
+		state->pc = orig_pc;
 	}
 #endif /* CONFIG_FUNCTION_GRAPH_TRACER */
 #ifdef CONFIG_KRETPROBES
-	if (is_kretprobe_trampoline(frame->pc))
-		frame->pc = kretprobe_find_ret_addr(tsk, (void *)frame->fp, &frame->kr_cur);
+	if (is_kretprobe_trampoline(state->pc))
+		state->pc = kretprobe_find_ret_addr(tsk, (void *)state->fp, &state->kr_cur);
 #endif
 
 	return 0;
 }
-NOKPROBE_SYMBOL(unwind_frame);
+NOKPROBE_SYMBOL(unwind_next);
 
-void notrace walk_stackframe(struct task_struct *tsk, struct stackframe *frame,
-			     bool (*fn)(void *, unsigned long), void *data)
+static void notrace unwind(struct unwind_state *state,
+			   stack_trace_consume_fn consume_entry, void *cookie)
 {
 	while (1) {
 		int ret;
 
-		if (!fn(data, frame->pc))
+		if (!consume_entry(cookie, state->pc))
 			break;
-		ret = unwind_frame(tsk, frame);
+		ret = unwind_next(state);
 		if (ret < 0)
 			break;
 	}
 }
-NOKPROBE_SYMBOL(walk_stackframe);
+NOKPROBE_SYMBOL(unwind);
 
-static void dump_backtrace_entry(unsigned long where, const char *loglvl)
+static bool dump_backtrace_entry(void *arg, unsigned long where)
 {
+	char *loglvl = arg;
 	printk("%s %pSb\n", loglvl, (void *)where);
+	return true;
 }
 
 void dump_backtrace(struct pt_regs *regs, struct task_struct *tsk,
 		    const char *loglvl)
 {
-	struct stackframe frame;
-	int skip = 0;
-
 	pr_debug("%s(regs = %p tsk = %p)\n", __func__, regs, tsk);
 
-	if (regs) {
-		if (user_mode(regs))
-			return;
-		skip = 1;
-	}
+	if (regs && user_mode(regs))
+		return;
 
 	if (!tsk)
 		tsk = current;
@@ -181,36 +152,8 @@ void dump_backtrace(struct pt_regs *regs, struct task_struct *tsk,
 	if (!try_get_task_stack(tsk))
 		return;
 
-	if (tsk == current) {
-		start_backtrace(&frame,
-				(unsigned long)__builtin_frame_address(0),
-				(unsigned long)dump_backtrace);
-	} else {
-		/*
-		 * task blocked in __switch_to
-		 */
-		start_backtrace(&frame,
-				thread_saved_fp(tsk),
-				thread_saved_pc(tsk));
-	}
-
 	printk("%sCall trace:\n", loglvl);
-	do {
-		/* skip until specified stack frame */
-		if (!skip) {
-			dump_backtrace_entry(frame.pc, loglvl);
-		} else if (frame.fp == regs->regs[29]) {
-			skip = 0;
-			/*
-			 * Mostly, this is the case where this function is
-			 * called in panic/abort. As exception handler's
-			 * stack frame does not contain the corresponding pc
-			 * at which an exception has taken place, use regs->pc
-			 * instead.
-			 */
-			dump_backtrace_entry(regs->pc, loglvl);
-		}
-	} while (!unwind_frame(tsk, &frame));
+	arch_stack_walk(dump_backtrace_entry, (void *)loglvl, tsk, regs);
 
 	put_task_stack(tsk);
 }
@@ -221,25 +164,57 @@ void show_stack(struct task_struct *tsk, unsigned long *sp, const char *loglvl)
 	barrier();
 }
 
-#ifdef CONFIG_STACKTRACE
+/*
+ * Per-cpu stacks are only accessible when unwinding the current task in a
+ * non-preemptible context.
+ */
+#define STACKINFO_CPU(name)					\
+	({							\
+		((task == current) && !preemptible())		\
+			? stackinfo_get_##name()		\
+			: stackinfo_get_unknown();		\
+	})
+
+/*
+ * SDEI stacks are only accessible when unwinding the current task in an NMI
+ * context.
+ */
+#define STACKINFO_SDEI(name)					\
+	({							\
+		((task == current) && in_nmi())			\
+			? stackinfo_get_sdei_##name()		\
+			: stackinfo_get_unknown();		\
+	})
 
 noinline notrace void arch_stack_walk(stack_trace_consume_fn consume_entry,
 			      void *cookie, struct task_struct *task,
 			      struct pt_regs *regs)
 {
-	struct stackframe frame;
-
-	if (regs)
-		start_backtrace(&frame, regs->regs[29], regs->pc);
-	else if (task == current)
-		start_backtrace(&frame,
-				(unsigned long)__builtin_frame_address(1),
-				(unsigned long)__builtin_return_address(0));
-	else
-		start_backtrace(&frame, thread_saved_fp(task),
-				thread_saved_pc(task));
-
-	walk_stackframe(task, &frame, consume_entry, cookie);
-}
-
+	struct stack_info stacks[] = {
+		stackinfo_get_task(task),
+		STACKINFO_CPU(irq),
+#if defined(CONFIG_VMAP_STACK)
+		STACKINFO_CPU(overflow),
+#endif
+#if defined(CONFIG_VMAP_STACK) && defined(CONFIG_ARM_SDE_INTERFACE)
+		STACKINFO_SDEI(normal),
+		STACKINFO_SDEI(critical),
 #endif
+	};
+	struct unwind_state state = {
+		.stacks = stacks,
+		.nr_stacks = ARRAY_SIZE(stacks),
+	};
+
+	if (regs) {
+		if (task != current)
+			return;
+		unwind_init_from_regs(&state, regs);
+	} else if (task == current) {
+		unwind_init_from_caller(&state);
+	} else {
+		unwind_init_from_task(&state, task);
+	}
+
+	unwind(&state, consume_entry, cookie);
+}
diff --git a/arch/arm64/kernel/suspend.c b/arch/arm64/kernel/suspend.c
index 19ee7c33769d..8b02d310838f 100644
--- a/arch/arm64/kernel/suspend.c
+++ b/arch/arm64/kernel/suspend.c
@@ -43,6 +43,8 @@ void notrace __cpu_suspend_exit(void)
 {
 	unsigned int cpu = smp_processor_id();
 
+	mte_suspend_exit();
+
 	/*
 	 * We are resuming from reset with the idmap active in TTBR0_EL1.
 	 * We must uninstall the idmap and restore the expected MMU
@@ -52,7 +54,7 @@ void notrace __cpu_suspend_exit(void)
 
 	/* Restore CnP bit in TTBR1_EL1 */
 	if (system_supports_cnp())
-		cpu_replace_ttbr1(lm_alias(swapper_pg_dir));
+		cpu_replace_ttbr1(lm_alias(swapper_pg_dir), idmap_pg_dir);
 
 	/*
 	 * PSTATE was not saved over suspend/resume, re-enable any detected
@@ -140,7 +142,7 @@ int cpu_suspend(unsigned long arg, int (*fn)(unsigned long))
 	/*
 	 * Restore pstate flags. OS lock and mdscr have been already
 	 * restored, so from this point onwards, debugging is fully
-	 * renabled if it was enabled when core started shutdown.
+	 * reenabled if it was enabled when core started shutdown.
 	 */
 	local_daif_restore(flags);
 
diff --git a/arch/arm64/kernel/sys_compat.c b/arch/arm64/kernel/sys_compat.c
index db5159a3055f..df14336c3a29 100644
--- a/arch/arm64/kernel/sys_compat.c
+++ b/arch/arm64/kernel/sys_compat.c
@@ -9,7 +9,6 @@
 
 #include <linux/compat.h>
 #include <linux/cpufeature.h>
-#include <linux/personality.h>
 #include <linux/sched.h>
 #include <linux/sched/signal.h>
 #include <linux/slab.h>
@@ -114,6 +113,6 @@ long compat_arm_syscall(struct pt_regs *regs, int scno)
 	addr = instruction_pointer(regs) - (compat_thumb_mode(regs) ? 2 : 4);
 
 	arm64_notify_die("Oops - bad compat syscall(2)", regs,
-			 SIGILL, ILL_ILLTRP, addr, scno);
+			 SIGILL, ILL_ILLTRP, addr, 0);
 	return 0;
 }
diff --git a/arch/arm64/kernel/syscall.c b/arch/arm64/kernel/syscall.c
index 50a0f1a38e84..d72e8f23422d 100644
--- a/arch/arm64/kernel/syscall.c
+++ b/arch/arm64/kernel/syscall.c
@@ -67,7 +67,7 @@ static void invoke_syscall(struct pt_regs *regs, unsigned int scno,
 	 *
 	 * The resulting 5 bits of entropy is seen in SP[8:4].
 	 */
-	choose_random_kstack_offset(get_random_int() & 0x1FF);
+	choose_random_kstack_offset(get_random_u16() & 0x1FF);
 }
 
 static inline bool has_syscall_work(unsigned long flags)
@@ -81,7 +81,7 @@ void syscall_trace_exit(struct pt_regs *regs);
 static void el0_svc_common(struct pt_regs *regs, int scno, int sc_nr,
 			   const syscall_fn_t syscall_table[])
 {
-	unsigned long flags = current_thread_info()->flags;
+	unsigned long flags = read_thread_flags();
 
 	regs->orig_x0 = regs->regs[0];
 	regs->syscallno = scno;
@@ -148,7 +148,7 @@ static void el0_svc_common(struct pt_regs *regs, int scno, int sc_nr,
 	 */
 	if (!has_syscall_work(flags) && !IS_ENABLED(CONFIG_DEBUG_RSEQ)) {
 		local_daif_mask();
-		flags = current_thread_info()->flags;
+		flags = read_thread_flags();
 		if (!has_syscall_work(flags) && !(flags & _TIF_SINGLESTEP))
 			return;
 		local_daif_restore(DAIF_PROCCTX);
@@ -158,11 +158,36 @@ trace_exit:
 	syscall_trace_exit(regs);
 }
 
-static inline void sve_user_discard(void)
+/*
+ * As per the ABI exit SME streaming mode and clear the SVE state not
+ * shared with FPSIMD on syscall entry.
+ */
+static inline void fp_user_discard(void)
 {
+	/*
+	 * If SME is active then exit streaming mode.  If ZA is active
+	 * then flush the SVE registers but leave userspace access to
+	 * both SVE and SME enabled, otherwise disable SME for the
+	 * task and fall through to disabling SVE too.  This means
+	 * that after a syscall we never have any streaming mode
+	 * register state to track, if this changes the KVM code will
+	 * need updating.
+	 */
+	if (system_supports_sme() && test_thread_flag(TIF_SME)) {
+		u64 svcr = read_sysreg_s(SYS_SVCR);
+
+		if (svcr & SVCR_SM_MASK)
+			sme_smstop_sm();
+	}
+
 	if (!system_supports_sve())
 		return;
 
+	/*
+	 * If SME is not active then disable SVE, the registers will
+	 * be cleared when userspace next attempts to access them and
+	 * we do not need to track the SVE register state until then.
+	 */
 	clear_thread_flag(TIF_SVE);
 
 	/*
@@ -177,7 +202,7 @@ static inline void sve_user_discard(void)
 
 void do_el0_svc(struct pt_regs *regs)
 {
-	sve_user_discard();
+	fp_user_discard();
 	el0_svc_common(regs, regs->regs[8], __NR_syscalls, sys_call_table);
 }
 
diff --git a/arch/arm64/kernel/time.c b/arch/arm64/kernel/time.c
index eebbc8d7123e..b5855eb7435d 100644
--- a/arch/arm64/kernel/time.c
+++ b/arch/arm64/kernel/time.c
@@ -18,6 +18,7 @@
 #include <linux/timex.h>
 #include <linux/errno.h>
 #include <linux/profile.h>
+#include <linux/stacktrace.h>
 #include <linux/syscore_ops.h>
 #include <linux/timer.h>
 #include <linux/irq.h>
@@ -29,25 +30,25 @@
 #include <clocksource/arm_arch_timer.h>
 
 #include <asm/thread_info.h>
-#include <asm/stacktrace.h>
 #include <asm/paravirt.h>
 
-unsigned long profile_pc(struct pt_regs *regs)
+static bool profile_pc_cb(void *arg, unsigned long pc)
 {
-	struct stackframe frame;
+	unsigned long *prof_pc = arg;
 
-	if (!in_lock_functions(regs->pc))
-		return regs->pc;
+	if (in_lock_functions(pc))
+		return true;
+	*prof_pc = pc;
+	return false;
+}
 
-	start_backtrace(&frame, regs->regs[29], regs->pc);
+unsigned long profile_pc(struct pt_regs *regs)
+{
+	unsigned long prof_pc = 0;
 
-	do {
-		int ret = unwind_frame(NULL, &frame);
-		if (ret < 0)
-			return 0;
-	} while (in_lock_functions(frame.pc));
+	arch_stack_walk(profile_pc_cb, &prof_pc, current, regs);
 
-	return frame.pc;
+	return prof_pc;
 }
 EXPORT_SYMBOL(profile_pc);
 
diff --git a/arch/arm64/kernel/topology.c b/arch/arm64/kernel/topology.c
index 9ab78ad826e2..817d788cd866 100644
--- a/arch/arm64/kernel/topology.c
+++ b/arch/arm64/kernel/topology.c
@@ -22,46 +22,6 @@
 #include <asm/cputype.h>
 #include <asm/topology.h>
 
-void store_cpu_topology(unsigned int cpuid)
-{
-	struct cpu_topology *cpuid_topo = &cpu_topology[cpuid];
-	u64 mpidr;
-
-	if (cpuid_topo->package_id != -1)
-		goto topology_populated;
-
-	mpidr = read_cpuid_mpidr();
-
-	/* Uniprocessor systems can rely on default topology values */
-	if (mpidr & MPIDR_UP_BITMASK)
-		return;
-
-	/*
-	 * This would be the place to create cpu topology based on MPIDR.
-	 *
-	 * However, it cannot be trusted to depict the actual topology; some
-	 * pieces of the architecture enforce an artificial cap on Aff0 values
-	 * (e.g. GICv3's ICC_SGI1R_EL1 limits it to 15), leading to an
-	 * artificial cycling of Aff1, Aff2 and Aff3 values. IOW, these end up
-	 * having absolutely no relationship to the actual underlying system
-	 * topology, and cannot be reasonably used as core / package ID.
-	 *
-	 * If the MT bit is set, Aff0 *could* be used to define a thread ID, but
-	 * we still wouldn't be able to obtain a sane core ID. This means we
-	 * need to entirely ignore MPIDR for any topology deduction.
-	 */
-	cpuid_topo->thread_id  = -1;
-	cpuid_topo->core_id    = cpuid;
-	cpuid_topo->package_id = cpu_to_node(cpuid);
-
-	pr_debug("CPU%u: cluster %d core %d thread %d mpidr %#016llx\n",
-		 cpuid, cpuid_topo->package_id, cpuid_topo->core_id,
-		 cpuid_topo->thread_id, mpidr);
-
-topology_populated:
-	update_siblings_masks(cpuid);
-}
-
 #ifdef CONFIG_ACPI
 static bool __init acpi_cpu_is_threaded(int cpu)
 {
@@ -89,8 +49,6 @@ int __init parse_acpi_topology(void)
 		return 0;
 
 	for_each_possible_cpu(cpu) {
-		int i, cache_id;
-
 		topology_id = find_acpi_cpu_topology(cpu, 0);
 		if (topology_id < 0)
 			return topology_id;
@@ -107,18 +65,6 @@ int __init parse_acpi_topology(void)
 		cpu_topology[cpu].cluster_id = topology_id;
 		topology_id = find_acpi_cpu_topology_package(cpu);
 		cpu_topology[cpu].package_id = topology_id;
-
-		i = acpi_find_last_cache_level(cpu);
-
-		if (i > 0) {
-			/*
-			 * this is the only part of cpu_topology that has
-			 * a direct relationship with the cache topology
-			 */
-			cache_id = find_acpi_cpu_cache_topology(cpu, i);
-			if (cache_id > 0)
-				cpu_topology[cpu].llc_id = cache_id;
-		}
 	}
 
 	return 0;
@@ -251,7 +197,7 @@ static void amu_fie_setup(const struct cpumask *cpus)
 	for_each_cpu(cpu, cpus) {
 		if (!freq_counters_valid(cpu) ||
 		    freq_inv_set_max_ratio(cpu,
-					   cpufreq_get_hw_max_freq(cpu) * 1000,
+					   cpufreq_get_hw_max_freq(cpu) * 1000ULL,
 					   arch_timer_get_rate()))
 			return;
 	}
@@ -310,12 +256,25 @@ core_initcall(init_amu_fie);
 
 static void cpu_read_corecnt(void *val)
 {
+	/*
+	 * A value of 0 can be returned if the current CPU does not support AMUs
+	 * or if the counter is disabled for this CPU. A return value of 0 at
+	 * counter read is properly handled as an error case by the users of the
+	 * counter.
+	 */
 	*(u64 *)val = read_corecnt();
 }
 
 static void cpu_read_constcnt(void *val)
 {
-	*(u64 *)val = read_constcnt();
+	/*
+	 * Return 0 if the current CPU is affected by erratum 2457168. A value
+	 * of 0 is also returned if the current CPU does not support AMUs or if
+	 * the counter is disabled. A return value of 0 at counter read is
+	 * properly handled as an error case by the users of the counter.
+	 */
+	*(u64 *)val = this_cpu_has_cap(ARM64_WORKAROUND_2457168) ?
+		      0UL : read_constcnt();
 }
 
 static inline
@@ -342,7 +301,22 @@ int counters_read_on_cpu(int cpu, smp_call_func_t func, u64 *val)
  */
 bool cpc_ffh_supported(void)
 {
-	return freq_counters_valid(get_cpu_with_amu_feat());
+	int cpu = get_cpu_with_amu_feat();
+
+	/*
+	 * FFH is considered supported if there is at least one present CPU that
+	 * supports AMUs. Using FFH to read core and reference counters for CPUs
+	 * that do not support AMUs, have counters disabled or that are affected
+	 * by errata, will result in a return value of 0.
+	 *
+	 * This is done to allow any enabled and valid counters to be read
+	 * through FFH, knowing that potentially returning 0 as counter value is
+	 * properly handled by the users of these counters.
+	 */
+	if ((cpu >= nr_cpu_ids) || !cpumask_test_cpu(cpu, cpu_present_mask))
+		return false;
+
+	return true;
 }
 
 int cpc_read_ffh(int cpu, struct cpc_reg *reg, u64 *val)
diff --git a/arch/arm64/kernel/traps.c b/arch/arm64/kernel/traps.c
index 7b21213a570f..23d281ed7621 100644
--- a/arch/arm64/kernel/traps.c
+++ b/arch/arm64/kernel/traps.c
@@ -9,7 +9,6 @@
 #include <linux/bug.h>
 #include <linux/context_tracking.h>
 #include <linux/signal.h>
-#include <linux/personality.h>
 #include <linux/kallsyms.h>
 #include <linux/kprobes.h>
 #include <linux/spinlock.h>
@@ -27,6 +26,7 @@
 #include <linux/syscalls.h>
 #include <linux/mm_types.h>
 #include <linux/kasan.h>
+#include <linux/cfi.h>
 
 #include <asm/atomic.h>
 #include <asm/bug.h>
@@ -181,12 +181,12 @@ static void dump_kernel_instr(const char *lvl, struct pt_regs *regs)
 
 #define S_SMP " SMP"
 
-static int __die(const char *str, int err, struct pt_regs *regs)
+static int __die(const char *str, long err, struct pt_regs *regs)
 {
 	static int die_counter;
 	int ret;
 
-	pr_emerg("Internal error: %s: %x [#%d]" S_PREEMPT S_SMP "\n",
+	pr_emerg("Internal error: %s: %016lx [#%d]" S_PREEMPT S_SMP "\n",
 		 str, err, ++die_counter);
 
 	/* trap and error numbers are mostly meaningless on ARM */
@@ -207,7 +207,7 @@ static DEFINE_RAW_SPINLOCK(die_lock);
 /*
  * This function is protected against re-entrancy.
  */
-void die(const char *str, struct pt_regs *regs, int err)
+void die(const char *str, struct pt_regs *regs, long err)
 {
 	int ret;
 	unsigned long flags;
@@ -235,7 +235,7 @@ void die(const char *str, struct pt_regs *regs, int err)
 	raw_spin_unlock_irqrestore(&die_lock, flags);
 
 	if (ret != NOTIFY_STOP)
-		do_exit(SIGSEGV);
+		make_task_dead(SIGSEGV);
 }
 
 static void arm64_show_signal(int signo, const char *str)
@@ -243,7 +243,7 @@ static void arm64_show_signal(int signo, const char *str)
 	static DEFINE_RATELIMIT_STATE(rs, DEFAULT_RATELIMIT_INTERVAL,
 				      DEFAULT_RATELIMIT_BURST);
 	struct task_struct *tsk = current;
-	unsigned int esr = tsk->thread.fault_code;
+	unsigned long esr = tsk->thread.fault_code;
 	struct pt_regs *regs = task_pt_regs(tsk);
 
 	/* Leave if the signal won't be shown */
@@ -254,7 +254,7 @@ static void arm64_show_signal(int signo, const char *str)
 
 	pr_info("%s[%d]: unhandled exception: ", tsk->comm, task_pid_nr(tsk));
 	if (esr)
-		pr_cont("%s, ESR 0x%08x, ", esr_get_class_string(esr), esr);
+		pr_cont("%s, ESR 0x%016lx, ", esr_get_class_string(esr), esr);
 
 	pr_cont("%s", str);
 	print_vma_addr(KERN_CONT " in ", regs->pc);
@@ -288,7 +288,7 @@ void arm64_force_sig_ptrace_errno_trap(int errno, unsigned long far,
 
 void arm64_notify_die(const char *str, struct pt_regs *regs,
 		      int signo, int sicode, unsigned long far,
-		      int err)
+		      unsigned long err)
 {
 	if (user_mode(regs)) {
 		WARN_ON(regs != current_pt_regs());
@@ -440,7 +440,7 @@ exit:
 	return fn ? fn(regs, instr) : 1;
 }
 
-void force_signal_inject(int signal, int code, unsigned long address, unsigned int err)
+void force_signal_inject(int signal, int code, unsigned long address, unsigned long err)
 {
 	const char *desc;
 	struct pt_regs *regs = current_pt_regs();
@@ -486,7 +486,7 @@ void arm64_notify_segfault(unsigned long addr)
 	force_signal_inject(SIGSEGV, code, addr, 0);
 }
 
-void do_undefinstr(struct pt_regs *regs)
+void do_undefinstr(struct pt_regs *regs, unsigned long esr)
 {
 	/* check for AArch32 breakpoint instructions */
 	if (!aarch32_break_handler(regs))
@@ -495,31 +495,41 @@ void do_undefinstr(struct pt_regs *regs)
 	if (call_undef_hook(regs) == 0)
 		return;
 
-	BUG_ON(!user_mode(regs));
+	if (!user_mode(regs))
+		die("Oops - Undefined instruction", regs, esr);
+
 	force_signal_inject(SIGILL, ILL_ILLOPC, regs->pc, 0);
 }
 NOKPROBE_SYMBOL(do_undefinstr);
 
-void do_bti(struct pt_regs *regs)
+void do_el0_bti(struct pt_regs *regs)
 {
-	BUG_ON(!user_mode(regs));
 	force_signal_inject(SIGILL, ILL_ILLOPC, regs->pc, 0);
 }
-NOKPROBE_SYMBOL(do_bti);
 
-void do_ptrauth_fault(struct pt_regs *regs, unsigned int esr)
+void do_el1_bti(struct pt_regs *regs, unsigned long esr)
+{
+	die("Oops - BTI", regs, esr);
+}
+NOKPROBE_SYMBOL(do_el1_bti);
+
+void do_el0_fpac(struct pt_regs *regs, unsigned long esr)
+{
+	force_signal_inject(SIGILL, ILL_ILLOPN, regs->pc, esr);
+}
+
+void do_el1_fpac(struct pt_regs *regs, unsigned long esr)
 {
 	/*
-	 * Unexpected FPAC exception or pointer authentication failure in
-	 * the kernel: kill the task before it does any more harm.
+	 * Unexpected FPAC exception in the kernel: kill the task before it
+	 * does any more harm.
 	 */
-	BUG_ON(!user_mode(regs));
-	force_signal_inject(SIGILL, ILL_ILLOPN, regs->pc, esr);
+	die("Oops - FPAC", regs, esr);
 }
-NOKPROBE_SYMBOL(do_ptrauth_fault);
+NOKPROBE_SYMBOL(do_el1_fpac)
 
 #define __user_cache_maint(insn, address, res)			\
-	if (address >= user_addr_max()) {			\
+	if (address >= TASK_SIZE_MAX) {				\
 		res = -EFAULT;					\
 	} else {						\
 		uaccess_ttbr0_enable();				\
@@ -533,7 +543,7 @@ NOKPROBE_SYMBOL(do_ptrauth_fault);
 		uaccess_ttbr0_disable();			\
 	}
 
-static void user_cache_maint_handler(unsigned int esr, struct pt_regs *regs)
+static void user_cache_maint_handler(unsigned long esr, struct pt_regs *regs)
 {
 	unsigned long tagged_address, address;
 	int rt = ESR_ELx_SYS64_ISS_RT(esr);
@@ -573,18 +583,18 @@ static void user_cache_maint_handler(unsigned int esr, struct pt_regs *regs)
 		arm64_skip_faulting_instruction(regs, AARCH64_INSN_SIZE);
 }
 
-static void ctr_read_handler(unsigned int esr, struct pt_regs *regs)
+static void ctr_read_handler(unsigned long esr, struct pt_regs *regs)
 {
 	int rt = ESR_ELx_SYS64_ISS_RT(esr);
 	unsigned long val = arm64_ftr_reg_user_value(&arm64_ftr_reg_ctrel0);
 
 	if (cpus_have_const_cap(ARM64_WORKAROUND_1542419)) {
 		/* Hide DIC so that we can trap the unnecessary maintenance...*/
-		val &= ~BIT(CTR_DIC_SHIFT);
+		val &= ~BIT(CTR_EL0_DIC_SHIFT);
 
 		/* ... and fake IminLine to reduce the number of traps. */
-		val &= ~CTR_IMINLINE_MASK;
-		val |= (PAGE_SHIFT - 2) & CTR_IMINLINE_MASK;
+		val &= ~CTR_EL0_IminLine_MASK;
+		val |= (PAGE_SHIFT - 2) & CTR_EL0_IminLine_MASK;
 	}
 
 	pt_regs_write_reg(regs, rt, val);
@@ -592,7 +602,7 @@ static void ctr_read_handler(unsigned int esr, struct pt_regs *regs)
 	arm64_skip_faulting_instruction(regs, AARCH64_INSN_SIZE);
 }
 
-static void cntvct_read_handler(unsigned int esr, struct pt_regs *regs)
+static void cntvct_read_handler(unsigned long esr, struct pt_regs *regs)
 {
 	int rt = ESR_ELx_SYS64_ISS_RT(esr);
 
@@ -600,7 +610,7 @@ static void cntvct_read_handler(unsigned int esr, struct pt_regs *regs)
 	arm64_skip_faulting_instruction(regs, AARCH64_INSN_SIZE);
 }
 
-static void cntfrq_read_handler(unsigned int esr, struct pt_regs *regs)
+static void cntfrq_read_handler(unsigned long esr, struct pt_regs *regs)
 {
 	int rt = ESR_ELx_SYS64_ISS_RT(esr);
 
@@ -608,7 +618,7 @@ static void cntfrq_read_handler(unsigned int esr, struct pt_regs *regs)
 	arm64_skip_faulting_instruction(regs, AARCH64_INSN_SIZE);
 }
 
-static void mrs_handler(unsigned int esr, struct pt_regs *regs)
+static void mrs_handler(unsigned long esr, struct pt_regs *regs)
 {
 	u32 sysreg, rt;
 
@@ -619,15 +629,15 @@ static void mrs_handler(unsigned int esr, struct pt_regs *regs)
 		force_signal_inject(SIGILL, ILL_ILLOPC, regs->pc, 0);
 }
 
-static void wfi_handler(unsigned int esr, struct pt_regs *regs)
+static void wfi_handler(unsigned long esr, struct pt_regs *regs)
 {
 	arm64_skip_faulting_instruction(regs, AARCH64_INSN_SIZE);
 }
 
 struct sys64_hook {
-	unsigned int esr_mask;
-	unsigned int esr_val;
-	void (*handler)(unsigned int esr, struct pt_regs *regs);
+	unsigned long esr_mask;
+	unsigned long esr_val;
+	void (*handler)(unsigned long esr, struct pt_regs *regs);
 };
 
 static const struct sys64_hook sys64_hooks[] = {
@@ -676,7 +686,7 @@ static const struct sys64_hook sys64_hooks[] = {
 };
 
 #ifdef CONFIG_COMPAT
-static bool cp15_cond_valid(unsigned int esr, struct pt_regs *regs)
+static bool cp15_cond_valid(unsigned long esr, struct pt_regs *regs)
 {
 	int cond;
 
@@ -696,7 +706,7 @@ static bool cp15_cond_valid(unsigned int esr, struct pt_regs *regs)
 	return aarch32_opcode_cond_checks[cond](regs->pstate);
 }
 
-static void compat_cntfrq_read_handler(unsigned int esr, struct pt_regs *regs)
+static void compat_cntfrq_read_handler(unsigned long esr, struct pt_regs *regs)
 {
 	int reg = (esr & ESR_ELx_CP15_32_ISS_RT_MASK) >> ESR_ELx_CP15_32_ISS_RT_SHIFT;
 
@@ -713,7 +723,7 @@ static const struct sys64_hook cp15_32_hooks[] = {
 	{},
 };
 
-static void compat_cntvct_read_handler(unsigned int esr, struct pt_regs *regs)
+static void compat_cntvct_read_handler(unsigned long esr, struct pt_regs *regs)
 {
 	int rt = (esr & ESR_ELx_CP15_64_ISS_RT_MASK) >> ESR_ELx_CP15_64_ISS_RT_SHIFT;
 	int rt2 = (esr & ESR_ELx_CP15_64_ISS_RT2_MASK) >> ESR_ELx_CP15_64_ISS_RT2_SHIFT;
@@ -738,7 +748,7 @@ static const struct sys64_hook cp15_64_hooks[] = {
 	{},
 };
 
-void do_cp15instr(unsigned int esr, struct pt_regs *regs)
+void do_cp15instr(unsigned long esr, struct pt_regs *regs)
 {
 	const struct sys64_hook *hook, *hook_base;
 
@@ -759,7 +769,7 @@ void do_cp15instr(unsigned int esr, struct pt_regs *regs)
 		hook_base = cp15_64_hooks;
 		break;
 	default:
-		do_undefinstr(regs);
+		do_undefinstr(regs, esr);
 		return;
 	}
 
@@ -774,12 +784,12 @@ void do_cp15instr(unsigned int esr, struct pt_regs *regs)
 	 * EL0. Fall back to our usual undefined instruction handler
 	 * so that we handle these consistently.
 	 */
-	do_undefinstr(regs);
+	do_undefinstr(regs, esr);
 }
 NOKPROBE_SYMBOL(do_cp15instr);
 #endif
 
-void do_sysinstr(unsigned int esr, struct pt_regs *regs)
+void do_sysinstr(unsigned long esr, struct pt_regs *regs)
 {
 	const struct sys64_hook *hook;
 
@@ -794,7 +804,7 @@ void do_sysinstr(unsigned int esr, struct pt_regs *regs)
 	 * back to our usual undefined instruction handler so that we handle
 	 * these consistently.
 	 */
-	do_undefinstr(regs);
+	do_undefinstr(regs, esr);
 }
 NOKPROBE_SYMBOL(do_sysinstr);
 
@@ -822,6 +832,7 @@ static const char *esr_class_str[] = {
 	[ESR_ELx_EC_SVE]		= "SVE",
 	[ESR_ELx_EC_ERET]		= "ERET/ERETAA/ERETAB",
 	[ESR_ELx_EC_FPAC]		= "FPAC",
+	[ESR_ELx_EC_SME]		= "SME",
 	[ESR_ELx_EC_IMP_DEF]		= "EL3 IMP DEF",
 	[ESR_ELx_EC_IABT_LOW]		= "IABT (lower EL)",
 	[ESR_ELx_EC_IABT_CUR]		= "IABT (current EL)",
@@ -843,7 +854,7 @@ static const char *esr_class_str[] = {
 	[ESR_ELx_EC_BRK64]		= "BRK (AArch64)",
 };
 
-const char *esr_get_class_string(u32 esr)
+const char *esr_get_class_string(unsigned long esr)
 {
 	return esr_class_str[ESR_ELx_EC(esr)];
 }
@@ -852,7 +863,7 @@ const char *esr_get_class_string(u32 esr)
  * bad_el0_sync handles unexpected, but potentially recoverable synchronous
  * exceptions taken from EL0.
  */
-void bad_el0_sync(struct pt_regs *regs, int reason, unsigned int esr)
+void bad_el0_sync(struct pt_regs *regs, int reason, unsigned long esr)
 {
 	unsigned long pc = instruction_pointer(regs);
 
@@ -868,7 +879,7 @@ void bad_el0_sync(struct pt_regs *regs, int reason, unsigned int esr)
 DEFINE_PER_CPU(unsigned long [OVERFLOW_STACK_SIZE/sizeof(long)], overflow_stack)
 	__aligned(16);
 
-void panic_bad_stack(struct pt_regs *regs, unsigned int esr, unsigned long far)
+void panic_bad_stack(struct pt_regs *regs, unsigned long esr, unsigned long far)
 {
 	unsigned long tsk_stk = (unsigned long)current->stack;
 	unsigned long irq_stk = (unsigned long)this_cpu_read(irq_stack_ptr);
@@ -877,7 +888,7 @@ void panic_bad_stack(struct pt_regs *regs, unsigned int esr, unsigned long far)
 	console_verbose();
 	pr_emerg("Insufficient stack space to handle exception!");
 
-	pr_emerg("ESR: 0x%08x -- %s\n", esr, esr_get_class_string(esr));
+	pr_emerg("ESR: 0x%016lx -- %s\n", esr, esr_get_class_string(esr));
 	pr_emerg("FAR: 0x%016lx\n", far);
 
 	pr_emerg("Task stack:     [0x%016lx..0x%016lx]\n",
@@ -898,11 +909,11 @@ void panic_bad_stack(struct pt_regs *regs, unsigned int esr, unsigned long far)
 }
 #endif
 
-void __noreturn arm64_serror_panic(struct pt_regs *regs, u32 esr)
+void __noreturn arm64_serror_panic(struct pt_regs *regs, unsigned long esr)
 {
 	console_verbose();
 
-	pr_crit("SError Interrupt on CPU%d, code 0x%08x -- %s\n",
+	pr_crit("SError Interrupt on CPU%d, code 0x%016lx -- %s\n",
 		smp_processor_id(), esr, esr_get_class_string(esr));
 	if (regs)
 		__show_regs(regs);
@@ -913,9 +924,9 @@ void __noreturn arm64_serror_panic(struct pt_regs *regs, u32 esr)
 	unreachable();
 }
 
-bool arm64_is_fatal_ras_serror(struct pt_regs *regs, unsigned int esr)
+bool arm64_is_fatal_ras_serror(struct pt_regs *regs, unsigned long esr)
 {
-	u32 aet = arm64_ras_serror_get_severity(esr);
+	unsigned long aet = arm64_ras_serror_get_severity(esr);
 
 	switch (aet) {
 	case ESR_ELx_AET_CE:	/* corrected error */
@@ -945,7 +956,7 @@ bool arm64_is_fatal_ras_serror(struct pt_regs *regs, unsigned int esr)
 	}
 }
 
-void do_serror(struct pt_regs *regs, unsigned int esr)
+void do_serror(struct pt_regs *regs, unsigned long esr)
 {
 	/* non-RAS errors are not containable */
 	if (!arm64_is_ras_serror(esr) || arm64_is_fatal_ras_serror(regs, esr))
@@ -966,11 +977,11 @@ int is_valid_bugaddr(unsigned long addr)
 	return 1;
 }
 
-static int bug_handler(struct pt_regs *regs, unsigned int esr)
+static int bug_handler(struct pt_regs *regs, unsigned long esr)
 {
 	switch (report_bug(regs->pc, regs)) {
 	case BUG_TRAP_TYPE_BUG:
-		die("Oops - BUG", regs, 0);
+		die("Oops - BUG", regs, esr);
 		break;
 
 	case BUG_TRAP_TYPE_WARN:
@@ -991,10 +1002,42 @@ static struct break_hook bug_break_hook = {
 	.imm = BUG_BRK_IMM,
 };
 
-static int reserved_fault_handler(struct pt_regs *regs, unsigned int esr)
+#ifdef CONFIG_CFI_CLANG
+static int cfi_handler(struct pt_regs *regs, unsigned long esr)
+{
+	unsigned long target;
+	u32 type;
+
+	target = pt_regs_read_reg(regs, FIELD_GET(CFI_BRK_IMM_TARGET, esr));
+	type = (u32)pt_regs_read_reg(regs, FIELD_GET(CFI_BRK_IMM_TYPE, esr));
+
+	switch (report_cfi_failure(regs, regs->pc, &target, type)) {
+	case BUG_TRAP_TYPE_BUG:
+		die("Oops - CFI", regs, 0);
+		break;
+
+	case BUG_TRAP_TYPE_WARN:
+		break;
+
+	default:
+		return DBG_HOOK_ERROR;
+	}
+
+	arm64_skip_faulting_instruction(regs, AARCH64_INSN_SIZE);
+	return DBG_HOOK_HANDLED;
+}
+
+static struct break_hook cfi_break_hook = {
+	.fn = cfi_handler,
+	.imm = CFI_BRK_IMM_BASE,
+	.mask = CFI_BRK_IMM_MASK,
+};
+#endif /* CONFIG_CFI_CLANG */
+
+static int reserved_fault_handler(struct pt_regs *regs, unsigned long esr)
 {
 	pr_err("%s generated an invalid instruction at %pS!\n",
-		in_bpf_jit(regs) ? "BPF JIT" : "Kernel text patching",
+		"Kernel text patching",
 		(void *)instruction_pointer(regs));
 
 	/* We cannot handle this */
@@ -1013,7 +1056,7 @@ static struct break_hook fault_break_hook = {
 #define KASAN_ESR_SIZE_MASK	0x0f
 #define KASAN_ESR_SIZE(esr)	(1 << ((esr) & KASAN_ESR_SIZE_MASK))
 
-static int kasan_handler(struct pt_regs *regs, unsigned int esr)
+static int kasan_handler(struct pt_regs *regs, unsigned long esr)
 {
 	bool recover = esr & KASAN_ESR_RECOVER;
 	bool write = esr & KASAN_ESR_WRITE;
@@ -1038,7 +1081,7 @@ static int kasan_handler(struct pt_regs *regs, unsigned int esr)
 	 * This is something that might be fixed at some point in the future.
 	 */
 	if (!recover)
-		die("Oops - KASAN", regs, 0);
+		die("Oops - KASAN", regs, esr);
 
 	/* If thread survives, skip over the brk instruction and continue: */
 	arm64_skip_faulting_instruction(regs, AARCH64_INSN_SIZE);
@@ -1052,17 +1095,22 @@ static struct break_hook kasan_break_hook = {
 };
 #endif
 
+
+#define esr_comment(esr) ((esr) & ESR_ELx_BRK64_ISS_COMMENT_MASK)
+
 /*
  * Initial handler for AArch64 BRK exceptions
  * This handler only used until debug_traps_init().
  */
-int __init early_brk64(unsigned long addr, unsigned int esr,
+int __init early_brk64(unsigned long addr, unsigned long esr,
 		struct pt_regs *regs)
 {
+#ifdef CONFIG_CFI_CLANG
+	if ((esr_comment(esr) & ~CFI_BRK_IMM_MASK) == CFI_BRK_IMM_BASE)
+		return cfi_handler(regs, esr) != DBG_HOOK_HANDLED;
+#endif
 #ifdef CONFIG_KASAN_SW_TAGS
-	unsigned int comment = esr & ESR_ELx_BRK64_ISS_COMMENT_MASK;
-
-	if ((comment & ~KASAN_BRK_MASK) == KASAN_BRK_IMM)
+	if ((esr_comment(esr) & ~KASAN_BRK_MASK) == KASAN_BRK_IMM)
 		return kasan_handler(regs, esr) != DBG_HOOK_HANDLED;
 #endif
 	return bug_handler(regs, esr) != DBG_HOOK_HANDLED;
@@ -1071,6 +1119,9 @@ int __init early_brk64(unsigned long addr, unsigned int esr,
 void __init trap_init(void)
 {
 	register_kernel_break_hook(&bug_break_hook);
+#ifdef CONFIG_CFI_CLANG
+	register_kernel_break_hook(&cfi_break_hook);
+#endif
 	register_kernel_break_hook(&fault_break_hook);
 #ifdef CONFIG_KASAN_SW_TAGS
 	register_kernel_break_hook(&kasan_break_hook);
diff --git a/arch/arm64/kernel/vdso.c b/arch/arm64/kernel/vdso.c
index a61fc4f989b3..99ae81ab91a7 100644
--- a/arch/arm64/kernel/vdso.c
+++ b/arch/arm64/kernel/vdso.c
@@ -29,9 +29,6 @@
 #include <asm/signal32.h>
 #include <asm/vdso.h>
 
-extern char vdso_start[], vdso_end[];
-extern char vdso32_start[], vdso32_end[];
-
 enum vdso_abi {
 	VDSO_ABI_AA64,
 	VDSO_ABI_AA32,
@@ -136,10 +133,11 @@ int vdso_join_timens(struct task_struct *task, struct time_namespace *ns)
 {
 	struct mm_struct *mm = task->mm;
 	struct vm_area_struct *vma;
+	VMA_ITERATOR(vmi, mm, 0);
 
 	mmap_read_lock(mm);
 
-	for (vma = mm->mmap; vma; vma = vma->vm_next) {
+	for_each_vma(vmi, vma) {
 		unsigned long size = vma->vm_end - vma->vm_start;
 
 		if (vma_is_special_mapping(vma, vdso_info[VDSO_ABI_AA64].dm))
diff --git a/arch/arm64/kernel/vdso/Makefile b/arch/arm64/kernel/vdso/Makefile
index 700767dfd221..619e2dc7ee14 100644
--- a/arch/arm64/kernel/vdso/Makefile
+++ b/arch/arm64/kernel/vdso/Makefile
@@ -24,14 +24,26 @@ btildflags-$(CONFIG_ARM64_BTI_KERNEL) += -z force-bti
 # routines, as x86 does (see 6f121e548f83 ("x86, vdso: Reimplement vdso.so
 # preparation in build-time C")).
 ldflags-y := -shared -soname=linux-vdso.so.1 --hash-style=sysv	\
-	     -Bsymbolic --build-id=sha1 -n $(btildflags-y) -T
+	     -Bsymbolic --build-id=sha1 -n $(btildflags-y)
+
+ifdef CONFIG_LD_ORPHAN_WARN
+  ldflags-y += --orphan-handling=warn
+endif
+
+ldflags-y += -T
 
 ccflags-y := -fno-common -fno-builtin -fno-stack-protector -ffixed-x18
 ccflags-y += -DDISABLE_BRANCH_PROFILING -DBUILD_VDSO
 
-CFLAGS_REMOVE_vgettimeofday.o = $(CC_FLAGS_FTRACE) -Os $(CC_FLAGS_SCS) $(GCC_PLUGINS_CFLAGS) \
-				$(CC_FLAGS_LTO)
+# -Wmissing-prototypes and -Wmissing-declarations are removed from
+# the CFLAGS of vgettimeofday.c to make possible to build the
+# kernel with CONFIG_WERROR enabled.
+CFLAGS_REMOVE_vgettimeofday.o = $(CC_FLAGS_FTRACE) -Os $(CC_FLAGS_SCS) \
+				$(RANDSTRUCT_CFLAGS) $(GCC_PLUGINS_CFLAGS) \
+				$(CC_FLAGS_LTO) $(CC_FLAGS_CFI) \
+				-Wmissing-prototypes -Wmissing-declarations
 KASAN_SANITIZE			:= n
+KCSAN_SANITIZE			:= n
 UBSAN_SANITIZE			:= n
 OBJECT_FILES_NON_STANDARD	:= y
 KCOV_INSTRUMENT			:= n
@@ -48,9 +60,6 @@ GCOV_PROFILE := n
 targets += vdso.lds
 CPPFLAGS_vdso.lds += -P -C -U$(ARCH)
 
-# Force dependency (incbin is bad)
-$(obj)/vdso.o : $(obj)/vdso.so
-
 # Link rule for the .so file, .lds has to be first
 $(obj)/vdso.so.dbg: $(obj)/vdso.lds $(obj-vdso) FORCE
 	$(call if_changed,vdsold_and_vdso_check)
diff --git a/arch/arm64/kernel/vdso/vdso.lds.S b/arch/arm64/kernel/vdso/vdso.lds.S
index a5e61e09ea92..6028f1fe2d1c 100644
--- a/arch/arm64/kernel/vdso/vdso.lds.S
+++ b/arch/arm64/kernel/vdso/vdso.lds.S
@@ -11,6 +11,7 @@
 #include <linux/const.h>
 #include <asm/page.h>
 #include <asm/vdso.h>
+#include <asm-generic/vmlinux.lds.h>
 
 OUTPUT_FORMAT("elf64-littleaarch64", "elf64-bigaarch64", "elf64-littleaarch64")
 OUTPUT_ARCH(aarch64)
@@ -47,13 +48,33 @@ SECTIONS
 	PROVIDE (_etext = .);
 	PROVIDE (etext = .);
 
+	. = ALIGN(4);
+	.altinstructions : {
+		__alt_instructions = .;
+		*(.altinstructions)
+		__alt_instructions_end = .;
+	}
+
 	.dynamic	: { *(.dynamic) }		:text	:dynamic
 
-	.rodata		: { *(.rodata*) }		:text
+	.rela.dyn	: ALIGN(8) { *(.rela .rela*) }
+
+	.rodata		: {
+		*(.rodata*)
+		*(.got)
+		*(.got.plt)
+		*(.plt)
+		*(.plt.*)
+		*(.iplt)
+		*(.igot .igot.plt)
+	}						:text
 
 	_end = .;
 	PROVIDE(end = .);
 
+	DWARF_DEBUG
+	ELF_DETAILS
+
 	/DISCARD/	: {
 		*(.data .data.* .gnu.linkonce.d.* .sdata*)
 		*(.bss .sbss .dynbss .dynsbss)
diff --git a/arch/arm64/kernel/vdso32/Makefile b/arch/arm64/kernel/vdso32/Makefile
index 6c01b63ff56d..36c8f66cad25 100644
--- a/arch/arm64/kernel/vdso32/Makefile
+++ b/arch/arm64/kernel/vdso32/Makefile
@@ -68,7 +68,8 @@ VDSO_CFLAGS += -Wall -Wundef -Wstrict-prototypes -Wno-trigraphs \
                -fno-strict-aliasing -fno-common \
                -Werror-implicit-function-declaration \
                -Wno-format-security \
-               -std=gnu89
+               -Wdeclaration-after-statement \
+               -std=gnu11
 VDSO_CFLAGS  += -O2
 # Some useful compiler-dependent flags from top-level Makefile
 VDSO_CFLAGS += $(call cc32-option,-Wdeclaration-after-statement,)
@@ -103,6 +104,7 @@ VDSO_AFLAGS += -D__ASSEMBLY__
 VDSO_LDFLAGS += -Bsymbolic --no-undefined -soname=linux-vdso.so.1
 VDSO_LDFLAGS += -z max-page-size=4096 -z common-page-size=4096
 VDSO_LDFLAGS += -shared --hash-style=sysv --build-id=sha1
+VDSO_LDFLAGS += --orphan-handling=warn
 
 
 # Borrow vdsomunge.c from the arm vDSO
@@ -130,9 +132,6 @@ obj-vdso := $(c-obj-vdso) $(c-obj-vdso-gettimeofday) $(asm-obj-vdso)
 targets += vdso.lds
 CPPFLAGS_vdso.lds += -P -C -U$(ARCH)
 
-# Force dependency (vdso.s includes vdso.so through incbin)
-$(obj)/vdso.o: $(obj)/vdso.so
-
 include/generated/vdso32-offsets.h: $(obj)/vdso.so.dbg FORCE
 	$(call if_changed,vdsosym)
 
diff --git a/arch/arm64/kernel/vdso32/vdso.lds.S b/arch/arm64/kernel/vdso32/vdso.lds.S
index 3348ce5ea306..8d95d7d35057 100644
--- a/arch/arm64/kernel/vdso32/vdso.lds.S
+++ b/arch/arm64/kernel/vdso32/vdso.lds.S
@@ -11,6 +11,7 @@
 #include <linux/const.h>
 #include <asm/page.h>
 #include <asm/vdso.h>
+#include <asm-generic/vmlinux.lds.h>
 
 OUTPUT_FORMAT("elf32-littlearm", "elf32-bigarm", "elf32-littlearm")
 OUTPUT_ARCH(arm)
@@ -35,12 +36,30 @@ SECTIONS
 
 	.dynamic	: { *(.dynamic) }		:text	:dynamic
 
-	.rodata		: { *(.rodata*) }		:text
+	.rodata		: {
+		*(.rodata*)
+		*(.got)
+		*(.got.plt)
+		*(.plt)
+		*(.rel.iplt)
+		*(.iplt)
+		*(.igot.plt)
+	}						:text
 
-	.text		: { *(.text*) }			:text	=0xe7f001f2
+	.text		: {
+		*(.text*)
+		*(.glue_7)
+		*(.glue_7t)
+		*(.vfp11_veneer)
+		*(.v4_bx)
+	}						:text	=0xe7f001f2
 
-	.got		: { *(.got) }
-	.rel.plt	: { *(.rel.plt) }
+	.rel.dyn	: { *(.rel*) }
+
+	.ARM.exidx : { *(.ARM.exidx*) }
+	DWARF_DEBUG
+	ELF_DETAILS
+	.ARM.attributes 0 : { *(.ARM.attributes) }
 
 	/DISCARD/	: {
 		*(.note.GNU-stack)
diff --git a/arch/arm64/kernel/vmlinux.lds.S b/arch/arm64/kernel/vmlinux.lds.S
index 50bab186c49b..45131e354e27 100644
--- a/arch/arm64/kernel/vmlinux.lds.S
+++ b/arch/arm64/kernel/vmlinux.lds.S
@@ -93,7 +93,6 @@ jiffies = jiffies_64;
 
 #ifdef CONFIG_HIBERNATION
 #define HIBERNATE_TEXT					\
-	. = ALIGN(SZ_4K);				\
 	__hibernate_exit_text_start = .;		\
 	*(.hibernate_exit.text)				\
 	__hibernate_exit_text_end = .;
@@ -103,7 +102,6 @@ jiffies = jiffies_64;
 
 #ifdef CONFIG_KEXEC_CORE
 #define KEXEC_TEXT					\
-	. = ALIGN(SZ_4K);				\
 	__relocate_new_kernel_start = .;		\
 	*(.kexec_relocate.text)				\
 	__relocate_new_kernel_end = .;
@@ -117,7 +115,8 @@ jiffies = jiffies_64;
 	__entry_tramp_text_start = .;			\
 	*(.entry.tramp.text)				\
 	. = ALIGN(PAGE_SIZE);				\
-	__entry_tramp_text_end = .;
+	__entry_tramp_text_end = .;			\
+	*(.entry.tramp.rodata)
 #else
 #define TRAMP_TEXT
 #endif
@@ -170,9 +169,6 @@ SECTIONS
 			KPROBES_TEXT
 			HYPERVISOR_TEXT
 			IDMAP_TEXT
-			HIBERNATE_TEXT
-			KEXEC_TEXT
-			TRAMP_TEXT
 			*(.gnu.warning)
 		. = ALIGN(16);
 		*(.got)			/* Global offset table		*/
@@ -194,9 +190,16 @@ SECTIONS
 
 	HYPERVISOR_DATA_SECTIONS
 
+	/* code sections that are never executed via the kernel mapping */
+	.rodata.text : {
+		TRAMP_TEXT
+		HIBERNATE_TEXT
+		KEXEC_TEXT
+		. = ALIGN(PAGE_SIZE);
+	}
+
 	idmap_pg_dir = .;
-	. += IDMAP_DIR_SIZE;
-	idmap_pg_end = .;
+	. += PAGE_SIZE;
 
 #ifdef CONFIG_UNMAP_KERNEL_AT_EL0
 	tramp_pg_dir = .;
@@ -232,6 +235,10 @@ SECTIONS
 	__inittext_end = .;
 	__initdata_begin = .;
 
+	init_idmap_pg_dir = .;
+	. += INIT_IDMAP_DIR_SIZE;
+	init_idmap_pg_end = .;
+
 	.init.data : {
 		INIT_DATA
 		INIT_SETUP(16)
@@ -250,21 +257,17 @@ SECTIONS
 	HYPERVISOR_RELOC_SECTION
 
 	.rela.dyn : ALIGN(8) {
+		__rela_start = .;
 		*(.rela .rela*)
+		__rela_end = .;
 	}
 
-	__rela_offset	= ABSOLUTE(ADDR(.rela.dyn) - KIMAGE_VADDR);
-	__rela_size	= SIZEOF(.rela.dyn);
-
-#ifdef CONFIG_RELR
 	.relr.dyn : ALIGN(8) {
+		__relr_start = .;
 		*(.relr.dyn)
+		__relr_end = .;
 	}
 
-	__relr_offset	= ABSOLUTE(ADDR(.relr.dyn) - KIMAGE_VADDR);
-	__relr_size	= SIZEOF(.relr.dyn);
-#endif
-
 	. = ALIGN(SEGMENT_ALIGN);
 	__initdata_end = .;
 	__init_end = .;
@@ -337,11 +340,11 @@ ASSERT(__hyp_idmap_text_end - __hyp_idmap_text_start <= PAGE_SIZE,
 ASSERT(__idmap_text_end - (__idmap_text_start & ~(SZ_4K - 1)) <= SZ_4K,
 	"ID map text too big or misaligned")
 #ifdef CONFIG_HIBERNATION
-ASSERT(__hibernate_exit_text_end - (__hibernate_exit_text_start & ~(SZ_4K - 1))
-	<= SZ_4K, "Hibernate exit text too big or misaligned")
+ASSERT(__hibernate_exit_text_end - __hibernate_exit_text_start <= SZ_4K,
+       "Hibernate exit text is bigger than 4 KiB")
 #endif
 #ifdef CONFIG_UNMAP_KERNEL_AT_EL0
-ASSERT((__entry_tramp_text_end - __entry_tramp_text_start) == PAGE_SIZE,
+ASSERT((__entry_tramp_text_end - __entry_tramp_text_start) <= 3*PAGE_SIZE,
 	"Entry trampoline text too big")
 #endif
 #ifdef CONFIG_KVM
@@ -362,7 +365,7 @@ ASSERT(swapper_pg_dir - tramp_pg_dir == TRAMP_SWAPPER_OFFSET,
 
 #ifdef CONFIG_KEXEC_CORE
 /* kexec relocation code should fit into one KEXEC_CONTROL_PAGE_SIZE */
-ASSERT(__relocate_new_kernel_end - (__relocate_new_kernel_start & ~(SZ_4K - 1))
-	<= SZ_4K, "kexec relocation code is too big or misaligned")
+ASSERT(__relocate_new_kernel_end - __relocate_new_kernel_start <= SZ_4K,
+       "kexec relocation code is bigger than 4 KiB")
 ASSERT(KEXEC_CONTROL_PAGE_SIZE >= SZ_4K, "KEXEC_CONTROL_PAGE_SIZE is broken")
 #endif
diff --git a/arch/arm64/kvm/.gitignore b/arch/arm64/kvm/.gitignore
new file mode 100644
index 000000000000..6182aefb8302
--- /dev/null
+++ b/arch/arm64/kvm/.gitignore
@@ -0,0 +1,2 @@
+# SPDX-License-Identifier: GPL-2.0-only
+hyp_constants.h
diff --git a/arch/arm64/kvm/Kconfig b/arch/arm64/kvm/Kconfig
index 8ffcbe29395e..815cc118c675 100644
--- a/arch/arm64/kvm/Kconfig
+++ b/arch/arm64/kvm/Kconfig
@@ -39,6 +39,8 @@ menuconfig KVM
 	select HAVE_KVM_IRQ_BYPASS
 	select HAVE_KVM_VCPU_RUN_PID_CHANGE
 	select SCHED_INFO
+	select GUEST_PERF_EVENTS if PERF_EVENTS
+	select INTERVAL_TREE
 	help
 	  Support hosting virtualized guest machines.
 
@@ -54,4 +56,17 @@ config NVHE_EL2_DEBUG
 
 	  If unsure, say N.
 
+config PROTECTED_NVHE_STACKTRACE
+	bool "Protected KVM hypervisor stacktraces"
+	depends on NVHE_EL2_DEBUG
+	default n
+	help
+	  Say Y here to enable pKVM hypervisor stacktraces on hyp_panic()
+
+	  If using protected nVHE mode, but cannot afford the associated
+	  memory cost (less than 0.75 page per CPU) of pKVM stacktraces,
+	  say N.
+
+	  If unsure, or not using protected nVHE (pKVM), say N.
+
 endif # VIRTUALIZATION
diff --git a/arch/arm64/kvm/Makefile b/arch/arm64/kvm/Makefile
index 989bb5dad2c8..5e33c2d4645a 100644
--- a/arch/arm64/kvm/Makefile
+++ b/arch/arm64/kvm/Makefile
@@ -5,18 +5,16 @@
 
 ccflags-y += -I $(srctree)/$(src)
 
-KVM=../../../virt/kvm
+include $(srctree)/virt/kvm/Makefile.kvm
 
 obj-$(CONFIG_KVM) += kvm.o
 obj-$(CONFIG_KVM) += hyp/
 
-kvm-y := $(KVM)/kvm_main.o $(KVM)/coalesced_mmio.o $(KVM)/eventfd.o \
-	 $(KVM)/vfio.o $(KVM)/irqchip.o $(KVM)/binary_stats.o \
-	 arm.o mmu.o mmio.o psci.o perf.o hypercalls.o pvtime.o \
+kvm-y += arm.o mmu.o mmio.o psci.o hypercalls.o pvtime.o \
 	 inject_fault.o va_layout.o handle_exit.o \
-	 guest.o debug.o reset.o sys_regs.o \
-	 vgic-sys-reg-v3.o fpsimd.o pmu.o \
-	 arch_timer.o trng.o\
+	 guest.o debug.o reset.o sys_regs.o stacktrace.o \
+	 vgic-sys-reg-v3.o fpsimd.o pkvm.o \
+	 arch_timer.o trng.o vmid.o \
 	 vgic/vgic.o vgic/vgic-init.o \
 	 vgic/vgic-irqfd.o vgic/vgic-v2.o \
 	 vgic/vgic-v3.o vgic/vgic-v4.o \
@@ -24,4 +22,20 @@ kvm-y := $(KVM)/kvm_main.o $(KVM)/coalesced_mmio.o $(KVM)/eventfd.o \
 	 vgic/vgic-mmio-v3.o vgic/vgic-kvm-device.o \
 	 vgic/vgic-its.o vgic/vgic-debug.o
 
-kvm-$(CONFIG_HW_PERF_EVENTS)  += pmu-emul.o
+kvm-$(CONFIG_HW_PERF_EVENTS)  += pmu-emul.o pmu.o
+
+always-y := hyp_constants.h hyp-constants.s
+
+define rule_gen_hyp_constants
+	$(call filechk,offsets,__HYP_CONSTANTS_H__)
+endef
+
+CFLAGS_hyp-constants.o = -I $(srctree)/$(src)/hyp/include
+$(obj)/hyp-constants.s: $(src)/hyp/hyp-constants.c FORCE
+	$(call if_changed_dep,cc_s_c)
+
+$(obj)/hyp_constants.h: $(obj)/hyp-constants.s FORCE
+	$(call if_changed_rule,gen_hyp_constants)
+
+obj-kvm := $(addprefix $(obj)/, $(kvm-y))
+$(obj-kvm): $(obj)/hyp_constants.h
diff --git a/arch/arm64/kvm/arch_timer.c b/arch/arm64/kvm/arch_timer.c
index 3df67c127489..bb24a76b4224 100644
--- a/arch/arm64/kvm/arch_timer.c
+++ b/arch/arm64/kvm/arch_timer.c
@@ -208,18 +208,16 @@ static irqreturn_t kvm_arch_timer_handler(int irq, void *dev_id)
 	return IRQ_HANDLED;
 }
 
-static u64 kvm_timer_compute_delta(struct arch_timer_context *timer_ctx)
+static u64 kvm_counter_compute_delta(struct arch_timer_context *timer_ctx,
+				     u64 val)
 {
-	u64 cval, now;
+	u64 now = kvm_phys_timer_read() - timer_get_offset(timer_ctx);
 
-	cval = timer_get_cval(timer_ctx);
-	now = kvm_phys_timer_read() - timer_get_offset(timer_ctx);
-
-	if (now < cval) {
+	if (now < val) {
 		u64 ns;
 
 		ns = cyclecounter_cyc2ns(timecounter->cc,
-					 cval - now,
+					 val - now,
 					 timecounter->mask,
 					 &timecounter->frac);
 		return ns;
@@ -228,6 +226,11 @@ static u64 kvm_timer_compute_delta(struct arch_timer_context *timer_ctx)
 	return 0;
 }
 
+static u64 kvm_timer_compute_delta(struct arch_timer_context *timer_ctx)
+{
+	return kvm_counter_compute_delta(timer_ctx, timer_get_cval(timer_ctx));
+}
+
 static bool kvm_timer_irq_can_fire(struct arch_timer_context *timer_ctx)
 {
 	WARN_ON(timer_ctx && timer_ctx->loaded);
@@ -236,6 +239,20 @@ static bool kvm_timer_irq_can_fire(struct arch_timer_context *timer_ctx)
 		  (ARCH_TIMER_CTRL_IT_MASK | ARCH_TIMER_CTRL_ENABLE)) == ARCH_TIMER_CTRL_ENABLE);
 }
 
+static bool vcpu_has_wfit_active(struct kvm_vcpu *vcpu)
+{
+	return (cpus_have_final_cap(ARM64_HAS_WFXT) &&
+		vcpu_get_flag(vcpu, IN_WFIT));
+}
+
+static u64 wfit_delay_ns(struct kvm_vcpu *vcpu)
+{
+	struct arch_timer_context *ctx = vcpu_vtimer(vcpu);
+	u64 val = vcpu_get_reg(vcpu, kvm_vcpu_sys_get_rt(vcpu));
+
+	return kvm_counter_compute_delta(ctx, val);
+}
+
 /*
  * Returns the earliest expiration time in ns among guest timers.
  * Note that it will return 0 if none of timers can fire.
@@ -253,6 +270,9 @@ static u64 kvm_timer_earliest_exp(struct kvm_vcpu *vcpu)
 			min_delta = min(min_delta, kvm_timer_compute_delta(ctx));
 	}
 
+	if (vcpu_has_wfit_active(vcpu))
+		min_delta = min(min_delta, wfit_delay_ns(vcpu));
+
 	/* If none of timers can fire, then return 0 */
 	if (min_delta == ULLONG_MAX)
 		return 0;
@@ -350,15 +370,9 @@ static bool kvm_timer_should_fire(struct arch_timer_context *timer_ctx)
 	return cval <= now;
 }
 
-bool kvm_timer_is_pending(struct kvm_vcpu *vcpu)
+int kvm_cpu_has_pending_timer(struct kvm_vcpu *vcpu)
 {
-	struct timer_map map;
-
-	get_timer_map(vcpu, &map);
-
-	return kvm_timer_should_fire(map.direct_vtimer) ||
-	       kvm_timer_should_fire(map.direct_ptimer) ||
-	       kvm_timer_should_fire(map.emul_ptimer);
+	return vcpu_has_wfit_active(vcpu) && wfit_delay_ns(vcpu) == 0;
 }
 
 /*
@@ -467,7 +481,7 @@ out:
 }
 
 /*
- * Schedule the background timer before calling kvm_vcpu_block, so that this
+ * Schedule the background timer before calling kvm_vcpu_halt, so that this
  * thread is removed from its waitqueue and made runnable when there's a timer
  * interrupt to handle.
  */
@@ -484,7 +498,8 @@ static void kvm_timer_blocking(struct kvm_vcpu *vcpu)
 	 */
 	if (!kvm_timer_irq_can_fire(map.direct_vtimer) &&
 	    !kvm_timer_irq_can_fire(map.direct_ptimer) &&
-	    !kvm_timer_irq_can_fire(map.emul_ptimer))
+	    !kvm_timer_irq_can_fire(map.emul_ptimer) &&
+	    !vcpu_has_wfit_active(vcpu))
 		return;
 
 	/*
@@ -649,7 +664,6 @@ void kvm_timer_vcpu_put(struct kvm_vcpu *vcpu)
 {
 	struct arch_timer_cpu *timer = vcpu_timer(vcpu);
 	struct timer_map map;
-	struct rcuwait *wait = kvm_arch_vcpu_get_wait(vcpu);
 
 	if (unlikely(!timer->enabled))
 		return;
@@ -672,7 +686,7 @@ void kvm_timer_vcpu_put(struct kvm_vcpu *vcpu)
 	if (map.emul_ptimer)
 		soft_timer_cancel(&map.emul_ptimer->hrtimer);
 
-	if (rcuwait_active(wait))
+	if (kvm_vcpu_is_blocking(vcpu))
 		kvm_timer_blocking(vcpu);
 
 	/*
@@ -750,7 +764,7 @@ int kvm_timer_vcpu_reset(struct kvm_vcpu *vcpu)
 /* Make the updates of cntvoff for all vtimer contexts atomic */
 static void update_vtimer_cntvoff(struct kvm_vcpu *vcpu, u64 cntvoff)
 {
-	int i;
+	unsigned long i;
 	struct kvm *kvm = vcpu->kvm;
 	struct kvm_vcpu *tmp;
 
@@ -1189,8 +1203,8 @@ void kvm_timer_vcpu_terminate(struct kvm_vcpu *vcpu)
 
 static bool timer_irqs_are_valid(struct kvm_vcpu *vcpu)
 {
-	int vtimer_irq, ptimer_irq;
-	int i, ret;
+	int vtimer_irq, ptimer_irq, ret;
+	unsigned long i;
 
 	vtimer_irq = vcpu_vtimer(vcpu)->irq.irq;
 	ret = kvm_vgic_set_owner(vcpu, vtimer_irq, vcpu_vtimer(vcpu));
@@ -1216,6 +1230,9 @@ bool kvm_arch_timer_get_input_level(int vintid)
 	struct kvm_vcpu *vcpu = kvm_get_running_vcpu();
 	struct arch_timer_context *timer;
 
+	if (WARN(!vcpu, "No vcpu context!\n"))
+		return false;
+
 	if (vintid == vcpu_vtimer(vcpu)->irq.irq)
 		timer = vcpu_vtimer(vcpu);
 	else if (vintid == vcpu_ptimer(vcpu)->irq.irq)
@@ -1297,7 +1314,7 @@ void kvm_timer_init_vhe(void)
 static void set_timer_irqs(struct kvm *kvm, int vtimer_irq, int ptimer_irq)
 {
 	struct kvm_vcpu *vcpu;
-	int i;
+	unsigned long i;
 
 	kvm_for_each_vcpu(i, vcpu, kvm) {
 		vcpu_vtimer(vcpu)->irq.irq = vtimer_irq;
diff --git a/arch/arm64/kvm/arm.c b/arch/arm64/kvm/arm.c
index e4727dc771bf..94d33e296e10 100644
--- a/arch/arm64/kvm/arm.c
+++ b/arch/arm64/kvm/arm.c
@@ -49,15 +49,10 @@ DEFINE_STATIC_KEY_FALSE(kvm_protected_mode_initialized);
 
 DECLARE_KVM_HYP_PER_CPU(unsigned long, kvm_hyp_vector);
 
-static DEFINE_PER_CPU(unsigned long, kvm_arm_hyp_stack_page);
+DEFINE_PER_CPU(unsigned long, kvm_arm_hyp_stack_page);
 unsigned long kvm_arm_hyp_percpu_base[NR_CPUS];
 DECLARE_KVM_NVHE_PER_CPU(struct kvm_nvhe_init_params, kvm_init_params);
 
-/* The VMID used in the VTTBR */
-static atomic64_t kvm_vmid_gen = ATOMIC64_INIT(1);
-static u32 kvm_next_vmid;
-static DEFINE_SPINLOCK(kvm_vmid_lock);
-
 static bool vgic_present;
 
 static DEFINE_PER_CPU(unsigned char, kvm_arm_hardware_enabled);
@@ -89,7 +84,8 @@ int kvm_vm_ioctl_enable_cap(struct kvm *kvm,
 	switch (cap->cap) {
 	case KVM_CAP_ARM_NISV_TO_USER:
 		r = 0;
-		kvm->arch.return_nisv_io_abort_to_user = true;
+		set_bit(KVM_ARCH_FLAG_RETURN_NISV_IO_ABORT_TO_USER,
+			&kvm->arch.flags);
 		break;
 	case KVM_CAP_ARM_MTE:
 		mutex_lock(&kvm->lock);
@@ -97,10 +93,14 @@ int kvm_vm_ioctl_enable_cap(struct kvm *kvm,
 			r = -EINVAL;
 		} else {
 			r = 0;
-			kvm->arch.mte_enabled = true;
+			set_bit(KVM_ARCH_FLAG_MTE_ENABLED, &kvm->arch.flags);
 		}
 		mutex_unlock(&kvm->lock);
 		break;
+	case KVM_CAP_ARM_SYSTEM_SUSPEND:
+		r = 0;
+		set_bit(KVM_ARCH_FLAG_SYSTEM_SUSPEND_ENABLED, &kvm->arch.flags);
+		break;
 	default:
 		r = -EINVAL;
 		break;
@@ -146,16 +146,23 @@ int kvm_arch_init_vm(struct kvm *kvm, unsigned long type)
 	if (ret)
 		return ret;
 
-	ret = create_hyp_mappings(kvm, kvm + 1, PAGE_HYP);
+	ret = kvm_share_hyp(kvm, kvm + 1);
 	if (ret)
 		goto out_free_stage2_pgd;
 
+	if (!zalloc_cpumask_var(&kvm->arch.supported_cpus, GFP_KERNEL)) {
+		ret = -ENOMEM;
+		goto out_free_stage2_pgd;
+	}
+	cpumask_copy(kvm->arch.supported_cpus, cpu_possible_mask);
+
 	kvm_vgic_early_init(kvm);
 
 	/* The maximum number of VCPUs is limited by the host's GIC model */
-	kvm->arch.max_vcpus = kvm_arm_default_max_vcpus();
+	kvm->max_vcpus = kvm_arm_default_max_vcpus();
 
 	set_default_spectre(kvm);
+	kvm_arm_init_hypercalls(kvm);
 
 	return ret;
 out_free_stage2_pgd:
@@ -175,19 +182,14 @@ vm_fault_t kvm_arch_vcpu_fault(struct kvm_vcpu *vcpu, struct vm_fault *vmf)
  */
 void kvm_arch_destroy_vm(struct kvm *kvm)
 {
-	int i;
-
 	bitmap_free(kvm->arch.pmu_filter);
+	free_cpumask_var(kvm->arch.supported_cpus);
 
 	kvm_vgic_destroy(kvm);
 
-	for (i = 0; i < KVM_MAX_VCPUS; ++i) {
-		if (kvm->vcpus[i]) {
-			kvm_vcpu_destroy(kvm->vcpus[i]);
-			kvm->vcpus[i] = NULL;
-		}
-	}
-	atomic_set(&kvm->online_vcpus, 0);
+	kvm_destroy_vcpus(kvm);
+
+	kvm_unshare_hyp(kvm, kvm + 1);
 }
 
 int kvm_vm_ioctl_check_extension(struct kvm *kvm, long ext)
@@ -215,6 +217,7 @@ int kvm_vm_ioctl_check_extension(struct kvm *kvm, long ext)
 	case KVM_CAP_SET_GUEST_DEBUG:
 	case KVM_CAP_VCPU_ATTRIBUTES:
 	case KVM_CAP_PTP_KVM:
+	case KVM_CAP_ARM_SYSTEM_SUSPEND:
 		r = 1;
 		break;
 	case KVM_CAP_SET_GUEST_DEBUG2:
@@ -235,7 +238,7 @@ int kvm_vm_ioctl_check_extension(struct kvm *kvm, long ext)
 	case KVM_CAP_MAX_VCPUS:
 	case KVM_CAP_MAX_VCPU_ID:
 		if (kvm)
-			r = kvm->arch.max_vcpus;
+			r = kvm->max_vcpus;
 		else
 			r = kvm_arm_default_max_vcpus();
 		break;
@@ -311,7 +314,7 @@ int kvm_arch_vcpu_precreate(struct kvm *kvm, unsigned int id)
 	if (irqchip_in_kernel(kvm) && vgic_initialized(kvm))
 		return -EBUSY;
 
-	if (id >= kvm->arch.max_vcpus)
+	if (id >= kvm->max_vcpus)
 		return -EINVAL;
 
 	return 0;
@@ -327,6 +330,12 @@ int kvm_arch_vcpu_create(struct kvm_vcpu *vcpu)
 
 	vcpu->arch.mmu_page_cache.gfp_zero = __GFP_ZERO;
 
+	/*
+	 * Default value for the FP state, will be overloaded at load
+	 * time if we support FP (pretty likely)
+	 */
+	vcpu->arch.fp_state = FP_STATE_FREE;
+
 	/* Set up the timer */
 	kvm_timer_vcpu_init(vcpu);
 
@@ -342,7 +351,7 @@ int kvm_arch_vcpu_create(struct kvm_vcpu *vcpu)
 	if (err)
 		return err;
 
-	return create_hyp_mappings(vcpu, vcpu + 1, PAGE_HYP);
+	return kvm_share_hyp(vcpu, vcpu + 1);
 }
 
 void kvm_arch_vcpu_postcreate(struct kvm_vcpu *vcpu)
@@ -351,7 +360,7 @@ void kvm_arch_vcpu_postcreate(struct kvm_vcpu *vcpu)
 
 void kvm_arch_vcpu_destroy(struct kvm_vcpu *vcpu)
 {
-	if (vcpu->arch.has_run_once && unlikely(!irqchip_in_kernel(vcpu->kvm)))
+	if (vcpu_has_run_once(vcpu) && unlikely(!irqchip_in_kernel(vcpu->kvm)))
 		static_branch_dec(&userspace_irqchip_in_use);
 
 	kvm_mmu_free_memory_cache(&vcpu->arch.mmu_page_cache);
@@ -361,34 +370,14 @@ void kvm_arch_vcpu_destroy(struct kvm_vcpu *vcpu)
 	kvm_arm_vcpu_destroy(vcpu);
 }
 
-int kvm_cpu_has_pending_timer(struct kvm_vcpu *vcpu)
-{
-	return kvm_timer_is_pending(vcpu);
-}
-
 void kvm_arch_vcpu_blocking(struct kvm_vcpu *vcpu)
 {
-	/*
-	 * If we're about to block (most likely because we've just hit a
-	 * WFI), we need to sync back the state of the GIC CPU interface
-	 * so that we have the latest PMR and group enables. This ensures
-	 * that kvm_arch_vcpu_runnable has up-to-date data to decide
-	 * whether we have pending interrupts.
-	 *
-	 * For the same reason, we want to tell GICv4 that we need
-	 * doorbells to be signalled, should an interrupt become pending.
-	 */
-	preempt_disable();
-	kvm_vgic_vmcr_sync(vcpu);
-	vgic_v4_put(vcpu, true);
-	preempt_enable();
+
 }
 
 void kvm_arch_vcpu_unblocking(struct kvm_vcpu *vcpu)
 {
-	preempt_disable();
-	vgic_v4_load(vcpu);
-	preempt_enable();
+
 }
 
 void kvm_arch_vcpu_load(struct kvm_vcpu *vcpu, int cpu)
@@ -432,6 +421,9 @@ void kvm_arch_vcpu_load(struct kvm_vcpu *vcpu, int cpu)
 	if (vcpu_has_ptrauth(vcpu))
 		vcpu_ptrauth_disable(vcpu);
 	kvm_arch_vcpu_load_debug_state_flags(vcpu);
+
+	if (!cpumask_test_cpu(smp_processor_id(), vcpu->kvm->arch.supported_cpus))
+		vcpu_set_on_unsupported_cpu(vcpu);
 }
 
 void kvm_arch_vcpu_put(struct kvm_vcpu *vcpu)
@@ -443,24 +435,40 @@ void kvm_arch_vcpu_put(struct kvm_vcpu *vcpu)
 	kvm_timer_vcpu_put(vcpu);
 	kvm_vgic_put(vcpu);
 	kvm_vcpu_pmu_restore_host(vcpu);
+	kvm_arm_vmid_clear_active();
 
+	vcpu_clear_on_unsupported_cpu(vcpu);
 	vcpu->cpu = -1;
 }
 
-static void vcpu_power_off(struct kvm_vcpu *vcpu)
+void kvm_arm_vcpu_power_off(struct kvm_vcpu *vcpu)
 {
-	vcpu->arch.power_off = true;
+	vcpu->arch.mp_state.mp_state = KVM_MP_STATE_STOPPED;
 	kvm_make_request(KVM_REQ_SLEEP, vcpu);
 	kvm_vcpu_kick(vcpu);
 }
 
+bool kvm_arm_vcpu_stopped(struct kvm_vcpu *vcpu)
+{
+	return vcpu->arch.mp_state.mp_state == KVM_MP_STATE_STOPPED;
+}
+
+static void kvm_arm_vcpu_suspend(struct kvm_vcpu *vcpu)
+{
+	vcpu->arch.mp_state.mp_state = KVM_MP_STATE_SUSPENDED;
+	kvm_make_request(KVM_REQ_SUSPEND, vcpu);
+	kvm_vcpu_kick(vcpu);
+}
+
+static bool kvm_arm_vcpu_suspended(struct kvm_vcpu *vcpu)
+{
+	return vcpu->arch.mp_state.mp_state == KVM_MP_STATE_SUSPENDED;
+}
+
 int kvm_arch_vcpu_ioctl_get_mpstate(struct kvm_vcpu *vcpu,
 				    struct kvm_mp_state *mp_state)
 {
-	if (vcpu->arch.power_off)
-		mp_state->mp_state = KVM_MP_STATE_STOPPED;
-	else
-		mp_state->mp_state = KVM_MP_STATE_RUNNABLE;
+	*mp_state = vcpu->arch.mp_state;
 
 	return 0;
 }
@@ -472,10 +480,13 @@ int kvm_arch_vcpu_ioctl_set_mpstate(struct kvm_vcpu *vcpu,
 
 	switch (mp_state->mp_state) {
 	case KVM_MP_STATE_RUNNABLE:
-		vcpu->arch.power_off = false;
+		vcpu->arch.mp_state = *mp_state;
 		break;
 	case KVM_MP_STATE_STOPPED:
-		vcpu_power_off(vcpu);
+		kvm_arm_vcpu_power_off(vcpu);
+		break;
+	case KVM_MP_STATE_SUSPENDED:
+		kvm_arm_vcpu_suspend(vcpu);
 		break;
 	default:
 		ret = -EINVAL;
@@ -495,7 +506,7 @@ int kvm_arch_vcpu_runnable(struct kvm_vcpu *v)
 {
 	bool irq_lines = *vcpu_hcr(v) & (HCR_VI | HCR_VF);
 	return ((irq_lines || kvm_vgic_vcpu_pending_irq(v))
-		&& !v->arch.power_off && !v->arch.pause);
+		&& !kvm_arm_vcpu_stopped(v) && !v->arch.pause);
 }
 
 bool kvm_arch_vcpu_in_kernel(struct kvm_vcpu *vcpu)
@@ -503,99 +514,40 @@ bool kvm_arch_vcpu_in_kernel(struct kvm_vcpu *vcpu)
 	return vcpu_mode_priv(vcpu);
 }
 
-/* Just ensure a guest exit from a particular CPU */
-static void exit_vm_noop(void *info)
+#ifdef CONFIG_GUEST_PERF_EVENTS
+unsigned long kvm_arch_vcpu_get_ip(struct kvm_vcpu *vcpu)
 {
+	return *vcpu_pc(vcpu);
 }
+#endif
 
-void force_vm_exit(const cpumask_t *mask)
-{
-	preempt_disable();
-	smp_call_function_many(mask, exit_vm_noop, NULL, true);
-	preempt_enable();
-}
-
-/**
- * need_new_vmid_gen - check that the VMID is still valid
- * @vmid: The VMID to check
- *
- * return true if there is a new generation of VMIDs being used
- *
- * The hardware supports a limited set of values with the value zero reserved
- * for the host, so we check if an assigned value belongs to a previous
- * generation, which requires us to assign a new value. If we're the first to
- * use a VMID for the new generation, we must flush necessary caches and TLBs
- * on all CPUs.
- */
-static bool need_new_vmid_gen(struct kvm_vmid *vmid)
+static int kvm_vcpu_initialized(struct kvm_vcpu *vcpu)
 {
-	u64 current_vmid_gen = atomic64_read(&kvm_vmid_gen);
-	smp_rmb(); /* Orders read of kvm_vmid_gen and kvm->arch.vmid */
-	return unlikely(READ_ONCE(vmid->vmid_gen) != current_vmid_gen);
+	return vcpu->arch.target >= 0;
 }
 
-/**
- * update_vmid - Update the vmid with a valid VMID for the current generation
- * @vmid: The stage-2 VMID information struct
+/*
+ * Handle both the initialisation that is being done when the vcpu is
+ * run for the first time, as well as the updates that must be
+ * performed each time we get a new thread dealing with this vcpu.
  */
-static void update_vmid(struct kvm_vmid *vmid)
-{
-	if (!need_new_vmid_gen(vmid))
-		return;
-
-	spin_lock(&kvm_vmid_lock);
-
-	/*
-	 * We need to re-check the vmid_gen here to ensure that if another vcpu
-	 * already allocated a valid vmid for this vm, then this vcpu should
-	 * use the same vmid.
-	 */
-	if (!need_new_vmid_gen(vmid)) {
-		spin_unlock(&kvm_vmid_lock);
-		return;
-	}
-
-	/* First user of a new VMID generation? */
-	if (unlikely(kvm_next_vmid == 0)) {
-		atomic64_inc(&kvm_vmid_gen);
-		kvm_next_vmid = 1;
-
-		/*
-		 * On SMP we know no other CPUs can use this CPU's or each
-		 * other's VMID after force_vm_exit returns since the
-		 * kvm_vmid_lock blocks them from reentry to the guest.
-		 */
-		force_vm_exit(cpu_all_mask);
-		/*
-		 * Now broadcast TLB + ICACHE invalidation over the inner
-		 * shareable domain to make sure all data structures are
-		 * clean.
-		 */
-		kvm_call_hyp(__kvm_flush_vm_context);
-	}
-
-	WRITE_ONCE(vmid->vmid, kvm_next_vmid);
-	kvm_next_vmid++;
-	kvm_next_vmid &= (1 << kvm_get_vmid_bits()) - 1;
-
-	smp_wmb();
-	WRITE_ONCE(vmid->vmid_gen, atomic64_read(&kvm_vmid_gen));
-
-	spin_unlock(&kvm_vmid_lock);
-}
-
-static int kvm_vcpu_first_run_init(struct kvm_vcpu *vcpu)
+int kvm_arch_vcpu_run_pid_change(struct kvm_vcpu *vcpu)
 {
 	struct kvm *kvm = vcpu->kvm;
-	int ret = 0;
+	int ret;
 
-	if (likely(vcpu->arch.has_run_once))
-		return 0;
+	if (!kvm_vcpu_initialized(vcpu))
+		return -ENOEXEC;
 
 	if (!kvm_arm_vcpu_is_finalized(vcpu))
 		return -EPERM;
 
-	vcpu->arch.has_run_once = true;
+	ret = kvm_arch_vcpu_run_map_fp(vcpu);
+	if (ret)
+		return ret;
+
+	if (likely(vcpu_has_run_once(vcpu)))
+		return 0;
 
 	kvm_arm_vcpu_init_debug(vcpu);
 
@@ -607,12 +559,6 @@ static int kvm_vcpu_first_run_init(struct kvm_vcpu *vcpu)
 		ret = kvm_vgic_map_resources(kvm);
 		if (ret)
 			return ret;
-	} else {
-		/*
-		 * Tell the rest of the code that there are userspace irqchip
-		 * VMs in the wild.
-		 */
-		static_branch_inc(&userspace_irqchip_in_use);
 	}
 
 	ret = kvm_timer_enable(vcpu);
@@ -620,6 +566,16 @@ static int kvm_vcpu_first_run_init(struct kvm_vcpu *vcpu)
 		return ret;
 
 	ret = kvm_arm_pmu_v3_enable(vcpu);
+	if (ret)
+		return ret;
+
+	if (!irqchip_in_kernel(kvm)) {
+		/*
+		 * Tell the rest of the code that there are userspace irqchip
+		 * VMs in the wild.
+		 */
+		static_branch_inc(&userspace_irqchip_in_use);
+	}
 
 	/*
 	 * Initialize traps for protected VMs.
@@ -629,6 +585,10 @@ static int kvm_vcpu_first_run_init(struct kvm_vcpu *vcpu)
 	if (kvm_vm_is_protected(kvm))
 		kvm_call_hyp_nvhe(__pkvm_vcpu_init_traps, vcpu);
 
+	mutex_lock(&kvm->lock);
+	set_bit(KVM_ARCH_FLAG_HAS_RAN_ONCE, &kvm->arch.flags);
+	mutex_unlock(&kvm->lock);
+
 	return ret;
 }
 
@@ -639,7 +599,7 @@ bool kvm_arch_intc_initialized(struct kvm *kvm)
 
 void kvm_arm_halt_guest(struct kvm *kvm)
 {
-	int i;
+	unsigned long i;
 	struct kvm_vcpu *vcpu;
 
 	kvm_for_each_vcpu(i, vcpu, kvm)
@@ -649,24 +609,24 @@ void kvm_arm_halt_guest(struct kvm *kvm)
 
 void kvm_arm_resume_guest(struct kvm *kvm)
 {
-	int i;
+	unsigned long i;
 	struct kvm_vcpu *vcpu;
 
 	kvm_for_each_vcpu(i, vcpu, kvm) {
 		vcpu->arch.pause = false;
-		rcuwait_wake_up(kvm_arch_vcpu_get_wait(vcpu));
+		__kvm_vcpu_wake_up(vcpu);
 	}
 }
 
-static void vcpu_req_sleep(struct kvm_vcpu *vcpu)
+static void kvm_vcpu_sleep(struct kvm_vcpu *vcpu)
 {
 	struct rcuwait *wait = kvm_arch_vcpu_get_wait(vcpu);
 
 	rcuwait_wait_event(wait,
-			   (!vcpu->arch.power_off) &&(!vcpu->arch.pause),
+			   (!kvm_arm_vcpu_stopped(vcpu)) && (!vcpu->arch.pause),
 			   TASK_INTERRUPTIBLE);
 
-	if (vcpu->arch.power_off || vcpu->arch.pause) {
+	if (kvm_arm_vcpu_stopped(vcpu) || vcpu->arch.pause) {
 		/* Awaken to handle a signal, request we sleep again later. */
 		kvm_make_request(KVM_REQ_SLEEP, vcpu);
 	}
@@ -679,16 +639,86 @@ static void vcpu_req_sleep(struct kvm_vcpu *vcpu)
 	smp_rmb();
 }
 
-static int kvm_vcpu_initialized(struct kvm_vcpu *vcpu)
+/**
+ * kvm_vcpu_wfi - emulate Wait-For-Interrupt behavior
+ * @vcpu:	The VCPU pointer
+ *
+ * Suspend execution of a vCPU until a valid wake event is detected, i.e. until
+ * the vCPU is runnable.  The vCPU may or may not be scheduled out, depending
+ * on when a wake event arrives, e.g. there may already be a pending wake event.
+ */
+void kvm_vcpu_wfi(struct kvm_vcpu *vcpu)
 {
-	return vcpu->arch.target >= 0;
+	/*
+	 * Sync back the state of the GIC CPU interface so that we have
+	 * the latest PMR and group enables. This ensures that
+	 * kvm_arch_vcpu_runnable has up-to-date data to decide whether
+	 * we have pending interrupts, e.g. when determining if the
+	 * vCPU should block.
+	 *
+	 * For the same reason, we want to tell GICv4 that we need
+	 * doorbells to be signalled, should an interrupt become pending.
+	 */
+	preempt_disable();
+	kvm_vgic_vmcr_sync(vcpu);
+	vgic_v4_put(vcpu, true);
+	preempt_enable();
+
+	kvm_vcpu_halt(vcpu);
+	vcpu_clear_flag(vcpu, IN_WFIT);
+
+	preempt_disable();
+	vgic_v4_load(vcpu);
+	preempt_enable();
 }
 
-static void check_vcpu_requests(struct kvm_vcpu *vcpu)
+static int kvm_vcpu_suspend(struct kvm_vcpu *vcpu)
+{
+	if (!kvm_arm_vcpu_suspended(vcpu))
+		return 1;
+
+	kvm_vcpu_wfi(vcpu);
+
+	/*
+	 * The suspend state is sticky; we do not leave it until userspace
+	 * explicitly marks the vCPU as runnable. Request that we suspend again
+	 * later.
+	 */
+	kvm_make_request(KVM_REQ_SUSPEND, vcpu);
+
+	/*
+	 * Check to make sure the vCPU is actually runnable. If so, exit to
+	 * userspace informing it of the wakeup condition.
+	 */
+	if (kvm_arch_vcpu_runnable(vcpu)) {
+		memset(&vcpu->run->system_event, 0, sizeof(vcpu->run->system_event));
+		vcpu->run->system_event.type = KVM_SYSTEM_EVENT_WAKEUP;
+		vcpu->run->exit_reason = KVM_EXIT_SYSTEM_EVENT;
+		return 0;
+	}
+
+	/*
+	 * Otherwise, we were unblocked to process a different event, such as a
+	 * pending signal. Return 1 and allow kvm_arch_vcpu_ioctl_run() to
+	 * process the event.
+	 */
+	return 1;
+}
+
+/**
+ * check_vcpu_requests - check and handle pending vCPU requests
+ * @vcpu:	the VCPU pointer
+ *
+ * Return: 1 if we should enter the guest
+ *	   0 if we should exit to userspace
+ *	   < 0 if we should exit to userspace, where the return value indicates
+ *	   an error
+ */
+static int check_vcpu_requests(struct kvm_vcpu *vcpu)
 {
 	if (kvm_request_pending(vcpu)) {
 		if (kvm_check_request(KVM_REQ_SLEEP, vcpu))
-			vcpu_req_sleep(vcpu);
+			kvm_vcpu_sleep(vcpu);
 
 		if (kvm_check_request(KVM_REQ_VCPU_RESET, vcpu))
 			kvm_reset_vcpu(vcpu);
@@ -713,7 +743,12 @@ static void check_vcpu_requests(struct kvm_vcpu *vcpu)
 		if (kvm_check_request(KVM_REQ_RELOAD_PMU, vcpu))
 			kvm_pmu_handle_pmcr(vcpu,
 					    __vcpu_sys_reg(vcpu, PMCR_EL0));
+
+		if (kvm_check_request(KVM_REQ_SUSPEND, vcpu))
+			return kvm_vcpu_suspend(vcpu);
 	}
+
+	return 1;
 }
 
 static bool vcpu_mode_is_bad_32bit(struct kvm_vcpu *vcpu)
@@ -721,8 +756,7 @@ static bool vcpu_mode_is_bad_32bit(struct kvm_vcpu *vcpu)
 	if (likely(!vcpu_mode_is_32bit(vcpu)))
 		return false;
 
-	return !system_supports_32bit_el0() ||
-		static_branch_unlikely(&arm64_mismatched_32bit_el0);
+	return !kvm_supports_32bit_el0();
 }
 
 /**
@@ -759,11 +793,36 @@ static bool kvm_vcpu_exit_request(struct kvm_vcpu *vcpu, int *ret)
 		}
 	}
 
+	if (unlikely(vcpu_on_unsupported_cpu(vcpu))) {
+		run->exit_reason = KVM_EXIT_FAIL_ENTRY;
+		run->fail_entry.hardware_entry_failure_reason = KVM_EXIT_FAIL_ENTRY_CPU_UNSUPPORTED;
+		run->fail_entry.cpu = smp_processor_id();
+		*ret = 0;
+		return true;
+	}
+
 	return kvm_request_pending(vcpu) ||
-			need_new_vmid_gen(&vcpu->arch.hw_mmu->vmid) ||
 			xfer_to_guest_mode_work_pending();
 }
 
+/*
+ * Actually run the vCPU, entering an RCU extended quiescent state (EQS) while
+ * the vCPU is running.
+ *
+ * This must be noinstr as instrumentation may make use of RCU, and this is not
+ * safe during the EQS.
+ */
+static int noinstr kvm_arm_vcpu_enter_exit(struct kvm_vcpu *vcpu)
+{
+	int ret;
+
+	guest_state_enter_irqoff();
+	ret = kvm_call_hyp_ret(__kvm_vcpu_run, vcpu);
+	guest_state_exit_irqoff();
+
+	return ret;
+}
+
 /**
  * kvm_arch_vcpu_ioctl_run - the main VCPU run function to execute guest code
  * @vcpu:	The VCPU pointer
@@ -779,13 +838,6 @@ int kvm_arch_vcpu_ioctl_run(struct kvm_vcpu *vcpu)
 	struct kvm_run *run = vcpu->run;
 	int ret;
 
-	if (unlikely(!kvm_vcpu_initialized(vcpu)))
-		return -ENOEXEC;
-
-	ret = kvm_vcpu_first_run_init(vcpu);
-	if (ret)
-		return ret;
-
 	if (run->exit_reason == KVM_EXIT_MMIO) {
 		ret = kvm_handle_mmio_return(vcpu);
 		if (ret)
@@ -803,6 +855,7 @@ int kvm_arch_vcpu_ioctl_run(struct kvm_vcpu *vcpu)
 
 	ret = 1;
 	run->exit_reason = KVM_EXIT_UNKNOWN;
+	run->flags = 0;
 	while (ret > 0) {
 		/*
 		 * Check conditions before entering the guest
@@ -811,9 +864,8 @@ int kvm_arch_vcpu_ioctl_run(struct kvm_vcpu *vcpu)
 		if (!ret)
 			ret = 1;
 
-		update_vmid(&vcpu->arch.hw_mmu->vmid);
-
-		check_vcpu_requests(vcpu);
+		if (ret > 0)
+			ret = check_vcpu_requests(vcpu);
 
 		/*
 		 * Preparing the interrupts to be injected also
@@ -822,12 +874,23 @@ int kvm_arch_vcpu_ioctl_run(struct kvm_vcpu *vcpu)
 		 */
 		preempt_disable();
 
+		/*
+		 * The VMID allocator only tracks active VMIDs per
+		 * physical CPU, and therefore the VMID allocated may not be
+		 * preserved on VMID roll-over if the task was preempted,
+		 * making a thread's VMID inactive. So we need to call
+		 * kvm_arm_vmid_update() in non-premptible context.
+		 */
+		kvm_arm_vmid_update(&vcpu->arch.hw_mmu->vmid);
+
 		kvm_pmu_flush_hwstate(vcpu);
 
 		local_irq_disable();
 
 		kvm_vgic_flush_hwstate(vcpu);
 
+		kvm_pmu_update_vcpu_events(vcpu);
+
 		/*
 		 * Ensure we set mode to IN_GUEST_MODE after we disable
 		 * interrupts and before the final VCPU requests check.
@@ -849,14 +912,15 @@ int kvm_arch_vcpu_ioctl_run(struct kvm_vcpu *vcpu)
 		}
 
 		kvm_arm_setup_debug(vcpu);
+		kvm_arch_vcpu_ctxflush_fp(vcpu);
 
 		/**************************************************************
 		 * Enter the guest
 		 */
 		trace_kvm_entry(*vcpu_pc(vcpu));
-		guest_enter_irqoff();
+		guest_timing_enter_irqoff();
 
-		ret = kvm_call_hyp_ret(__kvm_vcpu_run, vcpu);
+		ret = kvm_arm_vcpu_enter_exit(vcpu);
 
 		vcpu->mode = OUTSIDE_GUEST_MODE;
 		vcpu->stat.exits++;
@@ -891,26 +955,25 @@ int kvm_arch_vcpu_ioctl_run(struct kvm_vcpu *vcpu)
 		kvm_arch_vcpu_ctxsync_fp(vcpu);
 
 		/*
-		 * We may have taken a host interrupt in HYP mode (ie
-		 * while executing the guest). This interrupt is still
-		 * pending, as we haven't serviced it yet!
+		 * We must ensure that any pending interrupts are taken before
+		 * we exit guest timing so that timer ticks are accounted as
+		 * guest time. Transiently unmask interrupts so that any
+		 * pending interrupts are taken.
 		 *
-		 * We're now back in SVC mode, with interrupts
-		 * disabled.  Enabling the interrupts now will have
-		 * the effect of taking the interrupt again, in SVC
-		 * mode this time.
+		 * Per ARM DDI 0487G.b section D1.13.4, an ISB (or other
+		 * context synchronization event) is necessary to ensure that
+		 * pending interrupts are taken.
 		 */
+		if (ARM_EXCEPTION_CODE(ret) == ARM_EXCEPTION_IRQ) {
+			local_irq_enable();
+			isb();
+			local_irq_disable();
+		}
+
+		guest_timing_exit_irqoff();
+
 		local_irq_enable();
 
-		/*
-		 * We do local_irq_enable() before calling guest_exit() so
-		 * that if a timer interrupt hits while running the guest we
-		 * account that tick as being spent in the guest.  We enable
-		 * preemption after calling guest_exit() so that if we get
-		 * preempted we make sure ticks after that is not counted as
-		 * guest time.
-		 */
-		guest_exit();
 		trace_kvm_exit(ret, kvm_vcpu_trap_get_class(vcpu), *vcpu_pc(vcpu));
 
 		/* Exit types that need handling before we can be preempted */
@@ -956,8 +1019,8 @@ out:
 	 * the vcpu state. Note that this relies on __kvm_adjust_pc()
 	 * being preempt-safe on VHE.
 	 */
-	if (unlikely(vcpu->arch.flags & (KVM_ARM64_PENDING_EXCEPTION |
-					 KVM_ARM64_INCREMENT_PC)))
+	if (unlikely(vcpu_get_flag(vcpu, PENDING_EXCEPTION) ||
+		     vcpu_get_flag(vcpu, INCREMENT_PC)))
 		kvm_call_hyp(__kvm_adjust_pc, vcpu);
 
 	vcpu_put(vcpu);
@@ -1123,7 +1186,7 @@ static int kvm_arch_vcpu_ioctl_vcpu_init(struct kvm_vcpu *vcpu,
 	 * need to invalidate the I-cache though, as FWB does *not*
 	 * imply CTR_EL0.DIC.
 	 */
-	if (vcpu->arch.has_run_once) {
+	if (vcpu_has_run_once(vcpu)) {
 		if (!cpus_have_final_cap(ARM64_HAS_STAGE2_FWB))
 			stage2_unmap_vm(vcpu->kvm);
 		else
@@ -1137,9 +1200,9 @@ static int kvm_arch_vcpu_ioctl_vcpu_init(struct kvm_vcpu *vcpu,
 	 * Handle the "start in power-off" case.
 	 */
 	if (test_bit(KVM_ARM_VCPU_POWER_OFF, vcpu->arch.features))
-		vcpu_power_off(vcpu);
+		kvm_arm_vcpu_power_off(vcpu);
 	else
-		vcpu->arch.power_off = false;
+		vcpu->arch.mp_state.mp_state = KVM_MP_STATE_RUNNABLE;
 
 	return 0;
 }
@@ -1355,18 +1418,11 @@ void kvm_arch_flush_remote_tlbs_memslot(struct kvm *kvm,
 static int kvm_vm_ioctl_set_device_addr(struct kvm *kvm,
 					struct kvm_arm_device_addr *dev_addr)
 {
-	unsigned long dev_id, type;
-
-	dev_id = (dev_addr->id & KVM_ARM_DEVICE_ID_MASK) >>
-		KVM_ARM_DEVICE_ID_SHIFT;
-	type = (dev_addr->id & KVM_ARM_DEVICE_TYPE_MASK) >>
-		KVM_ARM_DEVICE_TYPE_SHIFT;
-
-	switch (dev_id) {
+	switch (FIELD_GET(KVM_ARM_DEVICE_ID_MASK, dev_addr->id)) {
 	case KVM_ARM_DEVICE_VGIC_V2:
 		if (!vgic_present)
 			return -ENXIO;
-		return kvm_vgic_addr(kvm, type, &dev_addr->addr, true);
+		return kvm_set_legacy_vgic_v2_addr(kvm, dev_addr);
 	default:
 		return -ENODEV;
 	}
@@ -1449,10 +1505,8 @@ static int kvm_init_vector_slots(void)
 	base = kern_hyp_va(kvm_ksym_ref(__bp_harden_hyp_vecs));
 	kvm_init_vector_slot(base, HYP_VECTOR_SPECTRE_DIRECT);
 
-	if (!cpus_have_const_cap(ARM64_SPECTRE_V3A))
-		return 0;
-
-	if (!has_vhe()) {
+	if (kvm_system_needs_idmapped_vectors() &&
+	    !is_protected_kvm_enabled()) {
 		err = create_hyp_exec_mappings(__pa_symbol(__bp_harden_hyp_vecs),
 					       __BP_HARDEN_HYP_VECS_SZ, &base);
 		if (err)
@@ -1499,7 +1553,6 @@ static void cpu_prepare_hyp_mode(int cpu)
 	tcr |= (idmap_t0sz & GENMASK(TCR_TxSZ_WIDTH - 1, 0)) << TCR_T0SZ_OFFSET;
 	params->tcr_el2 = tcr;
 
-	params->stack_hyp_va = kern_hyp_va(per_cpu(kvm_arm_hyp_stack_page, cpu) + PAGE_SIZE);
 	params->pgd_pa = kvm_mmu_get_httbr();
 	if (is_protected_kvm_enabled())
 		params->hcr_el2 = HCR_HOST_NVHE_PROTECTED_FLAGS;
@@ -1703,7 +1756,7 @@ static void init_cpu_logical_map(void)
 
 	/*
 	 * Copy the MPIDR <-> logical CPU ID mapping to hyp.
-	 * Only copy the set of online CPUs whose features have been chacked
+	 * Only copy the set of online CPUs whose features have been checked
 	 * against the finalized system capabilities. The hypervisor will not
 	 * allow any other CPUs from the `possible` set to boot.
 	 */
@@ -1775,8 +1828,7 @@ static int init_subsystems(void)
 	if (err)
 		goto out;
 
-	kvm_perf_init();
-	kvm_sys_reg_table_init();
+	kvm_register_perf_callbacks(NULL);
 
 out:
 	if (err || !is_protected_kvm_enabled())
@@ -1827,6 +1879,7 @@ static int kvm_hyp_init_protection(u32 hyp_va_bits)
 	kvm_nvhe_sym(id_aa64pfr1_el1_sys_val) = read_sanitised_ftr_reg(SYS_ID_AA64PFR1_EL1);
 	kvm_nvhe_sym(id_aa64isar0_el1_sys_val) = read_sanitised_ftr_reg(SYS_ID_AA64ISAR0_EL1);
 	kvm_nvhe_sym(id_aa64isar1_el1_sys_val) = read_sanitised_ftr_reg(SYS_ID_AA64ISAR1_EL1);
+	kvm_nvhe_sym(id_aa64isar2_el1_sys_val) = read_sanitised_ftr_reg(SYS_ID_AA64ISAR2_EL1);
 	kvm_nvhe_sym(id_aa64mmfr0_el1_sys_val) = read_sanitised_ftr_reg(SYS_ID_AA64MMFR0_EL1);
 	kvm_nvhe_sym(id_aa64mmfr1_el1_sys_val) = read_sanitised_ftr_reg(SYS_ID_AA64MMFR1_EL1);
 	kvm_nvhe_sym(id_aa64mmfr2_el1_sys_val) = read_sanitised_ftr_reg(SYS_ID_AA64MMFR2_EL1);
@@ -1947,14 +2000,46 @@ static int init_hyp_mode(void)
 	 * Map the Hyp stack pages
 	 */
 	for_each_possible_cpu(cpu) {
+		struct kvm_nvhe_init_params *params = per_cpu_ptr_nvhe_sym(kvm_init_params, cpu);
 		char *stack_page = (char *)per_cpu(kvm_arm_hyp_stack_page, cpu);
-		err = create_hyp_mappings(stack_page, stack_page + PAGE_SIZE,
-					  PAGE_HYP);
+		unsigned long hyp_addr;
 
+		/*
+		 * Allocate a contiguous HYP private VA range for the stack
+		 * and guard page. The allocation is also aligned based on
+		 * the order of its size.
+		 */
+		err = hyp_alloc_private_va_range(PAGE_SIZE * 2, &hyp_addr);
+		if (err) {
+			kvm_err("Cannot allocate hyp stack guard page\n");
+			goto out_err;
+		}
+
+		/*
+		 * Since the stack grows downwards, map the stack to the page
+		 * at the higher address and leave the lower guard page
+		 * unbacked.
+		 *
+		 * Any valid stack address now has the PAGE_SHIFT bit as 1
+		 * and addresses corresponding to the guard page have the
+		 * PAGE_SHIFT bit as 0 - this is used for overflow detection.
+		 */
+		err = __create_hyp_mappings(hyp_addr + PAGE_SIZE, PAGE_SIZE,
+					    __pa(stack_page), PAGE_HYP);
 		if (err) {
 			kvm_err("Cannot map hyp stack\n");
 			goto out_err;
 		}
+
+		/*
+		 * Save the stack PA in nvhe_init_params. This will be needed
+		 * to recreate the stack mapping in protected nVHE mode.
+		 * __hyp_pa() won't do the right thing there, since the stack
+		 * has been mapped in the flexible private VA space.
+		 */
+		params->stack_pa = __pa(stack_page);
+
+		params->stack_hyp_va = hyp_addr + (2 * PAGE_SIZE);
 	}
 
 	for_each_possible_cpu(cpu) {
@@ -2024,18 +2109,18 @@ static int finalize_hyp_mode(void)
 		return 0;
 
 	/*
-	 * Exclude HYP BSS from kmemleak so that it doesn't get peeked
-	 * at, which would end badly once the section is inaccessible.
-	 * None of other sections should ever be introspected.
+	 * Exclude HYP sections from kmemleak so that they don't get peeked
+	 * at, which would end badly once inaccessible.
 	 */
 	kmemleak_free_part(__hyp_bss_start, __hyp_bss_end - __hyp_bss_start);
+	kmemleak_free_part_phys(hyp_mem_base, hyp_mem_size);
 	return pkvm_drop_host_privileges();
 }
 
 struct kvm_vcpu *kvm_mpidr_to_vcpu(struct kvm *kvm, unsigned long mpidr)
 {
 	struct kvm_vcpu *vcpu;
-	int i;
+	unsigned long i;
 
 	mpidr &= MPIDR_HWID_BITMASK;
 	kvm_for_each_vcpu(i, vcpu, kvm) {
@@ -2103,6 +2188,12 @@ int kvm_arch_init(void *opaque)
 		return -ENODEV;
 	}
 
+	err = kvm_sys_reg_table_init();
+	if (err) {
+		kvm_info("Error initializing system register tables");
+		return err;
+	}
+
 	in_hyp_mode = is_kernel_in_hyp_mode();
 
 	if (cpus_have_final_cap(ARM64_WORKAROUND_DEVICE_LOAD_ACQUIRE) ||
@@ -2118,6 +2209,12 @@ int kvm_arch_init(void *opaque)
 	if (err)
 		return err;
 
+	err = kvm_arm_vmid_alloc_init();
+	if (err) {
+		kvm_err("Failed to initialize VMID allocator.\n");
+		return err;
+	}
+
 	if (!in_hyp_mode) {
 		err = init_hyp_mode();
 		if (err)
@@ -2157,13 +2254,14 @@ out_hyp:
 	if (!in_hyp_mode)
 		teardown_hyp_mode();
 out_err:
+	kvm_arm_vmid_alloc_free();
 	return err;
 }
 
 /* NOP: Compiling as a module not supported */
 void kvm_arch_exit(void)
 {
-	kvm_perf_teardown();
+	kvm_unregister_perf_callbacks();
 }
 
 static int __init early_kvm_mode_cfg(char *arg)
@@ -2171,18 +2269,27 @@ static int __init early_kvm_mode_cfg(char *arg)
 	if (!arg)
 		return -EINVAL;
 
-	if (strcmp(arg, "protected") == 0) {
-		kvm_mode = KVM_MODE_PROTECTED;
+	if (strcmp(arg, "none") == 0) {
+		kvm_mode = KVM_MODE_NONE;
 		return 0;
 	}
 
-	if (strcmp(arg, "nvhe") == 0 && !WARN_ON(is_kernel_in_hyp_mode())) {
-		kvm_mode = KVM_MODE_DEFAULT;
+	if (!is_hyp_mode_available()) {
+		pr_warn_once("KVM is not available. Ignoring kvm-arm.mode\n");
 		return 0;
 	}
 
-	if (strcmp(arg, "none") == 0) {
-		kvm_mode = KVM_MODE_NONE;
+	if (strcmp(arg, "protected") == 0) {
+		if (!is_kernel_in_hyp_mode())
+			kvm_mode = KVM_MODE_PROTECTED;
+		else
+			pr_warn_once("Protected KVM not available with VHE\n");
+
+		return 0;
+	}
+
+	if (strcmp(arg, "nvhe") == 0 && !WARN_ON(is_kernel_in_hyp_mode())) {
+		kvm_mode = KVM_MODE_DEFAULT;
 		return 0;
 	}
 
diff --git a/arch/arm64/kvm/debug.c b/arch/arm64/kvm/debug.c
index db9361338b2a..fccf9ec01813 100644
--- a/arch/arm64/kvm/debug.c
+++ b/arch/arm64/kvm/debug.c
@@ -32,6 +32,10 @@ static DEFINE_PER_CPU(u64, mdcr_el2);
  *
  * Guest access to MDSCR_EL1 is trapped by the hypervisor and handled
  * after we have restored the preserved value to the main context.
+ *
+ * When single-step is enabled by userspace, we tweak PSTATE.SS on every
+ * guest entry. Preserve PSTATE.SS so we can restore the original value
+ * for the vcpu after the single-step is disabled.
  */
 static void save_guest_debug_regs(struct kvm_vcpu *vcpu)
 {
@@ -41,6 +45,9 @@ static void save_guest_debug_regs(struct kvm_vcpu *vcpu)
 
 	trace_kvm_arm_set_dreg32("Saved MDSCR_EL1",
 				vcpu->arch.guest_debug_preserved.mdscr_el1);
+
+	vcpu->arch.guest_debug_preserved.pstate_ss =
+					(*vcpu_cpsr(vcpu) & DBG_SPSR_SS);
 }
 
 static void restore_guest_debug_regs(struct kvm_vcpu *vcpu)
@@ -51,6 +58,11 @@ static void restore_guest_debug_regs(struct kvm_vcpu *vcpu)
 
 	trace_kvm_arm_set_dreg32("Restored MDSCR_EL1",
 				vcpu_read_sys_reg(vcpu, MDSCR_EL1));
+
+	if (vcpu->arch.guest_debug_preserved.pstate_ss)
+		*vcpu_cpsr(vcpu) |= DBG_SPSR_SS;
+	else
+		*vcpu_cpsr(vcpu) &= ~DBG_SPSR_SS;
 }
 
 /**
@@ -104,10 +116,12 @@ static void kvm_arm_setup_mdcr_el2(struct kvm_vcpu *vcpu)
 	 * Trap debug register access when one of the following is true:
 	 *  - Userspace is using the hardware to debug the guest
 	 *  (KVM_GUESTDBG_USE_HW is set).
-	 *  - The guest is not using debug (KVM_ARM64_DEBUG_DIRTY is clear).
+	 *  - The guest is not using debug (DEBUG_DIRTY clear).
+	 *  - The guest has enabled the OS Lock (debug exceptions are blocked).
 	 */
 	if ((vcpu->guest_debug & KVM_GUESTDBG_USE_HW) ||
-	    !(vcpu->arch.flags & KVM_ARM64_DEBUG_DIRTY))
+	    !vcpu_get_flag(vcpu, DEBUG_DIRTY) ||
+	    kvm_vcpu_os_lock_enabled(vcpu))
 		vcpu->arch.mdcr_el2 |= MDCR_EL2_TDA;
 
 	trace_kvm_arm_set_dreg32("MDCR_EL2", vcpu->arch.mdcr_el2);
@@ -145,8 +159,8 @@ void kvm_arm_reset_debug_ptr(struct kvm_vcpu *vcpu)
  * debug related registers.
  *
  * Additionally, KVM only traps guest accesses to the debug registers if
- * the guest is not actively using them (see the KVM_ARM64_DEBUG_DIRTY
- * flag on vcpu->arch.flags).  Since the guest must not interfere
+ * the guest is not actively using them (see the DEBUG_DIRTY
+ * flag on vcpu->arch.iflags).  Since the guest must not interfere
  * with the hardware state when debugging the guest, we must ensure that
  * trapping is enabled whenever we are debugging the guest using the
  * debug registers.
@@ -160,8 +174,8 @@ void kvm_arm_setup_debug(struct kvm_vcpu *vcpu)
 
 	kvm_arm_setup_mdcr_el2(vcpu);
 
-	/* Is Guest debugging in effect? */
-	if (vcpu->guest_debug) {
+	/* Check if we need to use the debug registers. */
+	if (vcpu->guest_debug || kvm_vcpu_os_lock_enabled(vcpu)) {
 		/* Save guest debug state */
 		save_guest_debug_regs(vcpu);
 
@@ -186,7 +200,18 @@ void kvm_arm_setup_debug(struct kvm_vcpu *vcpu)
 		 * debugging the system.
 		 */
 		if (vcpu->guest_debug & KVM_GUESTDBG_SINGLESTEP) {
-			*vcpu_cpsr(vcpu) |=  DBG_SPSR_SS;
+			/*
+			 * If the software step state at the last guest exit
+			 * was Active-pending, we don't set DBG_SPSR_SS so
+			 * that the state is maintained (to not run another
+			 * single-step until the pending Software Step
+			 * exception is taken).
+			 */
+			if (!vcpu_get_flag(vcpu, DBG_SS_ACTIVE_PENDING))
+				*vcpu_cpsr(vcpu) |= DBG_SPSR_SS;
+			else
+				*vcpu_cpsr(vcpu) &= ~DBG_SPSR_SS;
+
 			mdscr = vcpu_read_sys_reg(vcpu, MDSCR_EL1);
 			mdscr |= DBG_MDSCR_SS;
 			vcpu_write_sys_reg(vcpu, mdscr, MDSCR_EL1);
@@ -203,9 +228,8 @@ void kvm_arm_setup_debug(struct kvm_vcpu *vcpu)
 		 *
 		 * We simply switch the debug_ptr to point to our new
 		 * external_debug_state which has been populated by the
-		 * debug ioctl. The existing KVM_ARM64_DEBUG_DIRTY
-		 * mechanism ensures the registers are updated on the
-		 * world switch.
+		 * debug ioctl. The existing DEBUG_DIRTY mechanism ensures
+		 * the registers are updated on the world switch.
 		 */
 		if (vcpu->guest_debug & KVM_GUESTDBG_USE_HW) {
 			/* Enable breakpoints/watchpoints */
@@ -214,7 +238,7 @@ void kvm_arm_setup_debug(struct kvm_vcpu *vcpu)
 			vcpu_write_sys_reg(vcpu, mdscr, MDSCR_EL1);
 
 			vcpu->arch.debug_ptr = &vcpu->arch.external_debug_state;
-			vcpu->arch.flags |= KVM_ARM64_DEBUG_DIRTY;
+			vcpu_set_flag(vcpu, DEBUG_DIRTY);
 
 			trace_kvm_arm_set_regset("BKPTS", get_num_brps(),
 						&vcpu->arch.debug_ptr->dbg_bcr[0],
@@ -223,6 +247,19 @@ void kvm_arm_setup_debug(struct kvm_vcpu *vcpu)
 			trace_kvm_arm_set_regset("WAPTS", get_num_wrps(),
 						&vcpu->arch.debug_ptr->dbg_wcr[0],
 						&vcpu->arch.debug_ptr->dbg_wvr[0]);
+
+		/*
+		 * The OS Lock blocks debug exceptions in all ELs when it is
+		 * enabled. If the guest has enabled the OS Lock, constrain its
+		 * effects to the guest. Emulate the behavior by clearing
+		 * MDSCR_EL1.MDE. In so doing, we ensure that host debug
+		 * exceptions are unaffected by guest configuration of the OS
+		 * Lock.
+		 */
+		} else if (kvm_vcpu_os_lock_enabled(vcpu)) {
+			mdscr = vcpu_read_sys_reg(vcpu, MDSCR_EL1);
+			mdscr &= ~DBG_MDSCR_MDE;
+			vcpu_write_sys_reg(vcpu, mdscr, MDSCR_EL1);
 		}
 	}
 
@@ -231,7 +268,7 @@ void kvm_arm_setup_debug(struct kvm_vcpu *vcpu)
 
 	/* If KDE or MDE are set, perform a full save/restore cycle. */
 	if (vcpu_read_sys_reg(vcpu, MDSCR_EL1) & (DBG_MDSCR_KDE | DBG_MDSCR_MDE))
-		vcpu->arch.flags |= KVM_ARM64_DEBUG_DIRTY;
+		vcpu_set_flag(vcpu, DEBUG_DIRTY);
 
 	/* Write mdcr_el2 changes since vcpu_load on VHE systems */
 	if (has_vhe() && orig_mdcr_el2 != vcpu->arch.mdcr_el2)
@@ -244,7 +281,19 @@ void kvm_arm_clear_debug(struct kvm_vcpu *vcpu)
 {
 	trace_kvm_arm_clear_debug(vcpu->guest_debug);
 
-	if (vcpu->guest_debug) {
+	/*
+	 * Restore the guest's debug registers if we were using them.
+	 */
+	if (vcpu->guest_debug || kvm_vcpu_os_lock_enabled(vcpu)) {
+		if (vcpu->guest_debug & KVM_GUESTDBG_SINGLESTEP) {
+			if (!(*vcpu_cpsr(vcpu) & DBG_SPSR_SS))
+				/*
+				 * Mark the vcpu as ACTIVE_PENDING
+				 * until Software Step exception is taken.
+				 */
+				vcpu_set_flag(vcpu, DBG_SS_ACTIVE_PENDING);
+		}
+
 		restore_guest_debug_regs(vcpu);
 
 		/*
@@ -278,18 +327,18 @@ void kvm_arch_vcpu_load_debug_state_flags(struct kvm_vcpu *vcpu)
 	 * If SPE is present on this CPU and is available at current EL,
 	 * we may need to check if the host state needs to be saved.
 	 */
-	if (cpuid_feature_extract_unsigned_field(dfr0, ID_AA64DFR0_PMSVER_SHIFT) &&
+	if (cpuid_feature_extract_unsigned_field(dfr0, ID_AA64DFR0_EL1_PMSVer_SHIFT) &&
 	    !(read_sysreg_s(SYS_PMBIDR_EL1) & BIT(SYS_PMBIDR_EL1_P_SHIFT)))
-		vcpu->arch.flags |= KVM_ARM64_DEBUG_STATE_SAVE_SPE;
+		vcpu_set_flag(vcpu, DEBUG_STATE_SAVE_SPE);
 
 	/* Check if we have TRBE implemented and available at the host */
-	if (cpuid_feature_extract_unsigned_field(dfr0, ID_AA64DFR0_TRBE_SHIFT) &&
+	if (cpuid_feature_extract_unsigned_field(dfr0, ID_AA64DFR0_EL1_TraceBuffer_SHIFT) &&
 	    !(read_sysreg_s(SYS_TRBIDR_EL1) & TRBIDR_PROG))
-		vcpu->arch.flags |= KVM_ARM64_DEBUG_STATE_SAVE_TRBE;
+		vcpu_set_flag(vcpu, DEBUG_STATE_SAVE_TRBE);
 }
 
 void kvm_arch_vcpu_put_debug_state_flags(struct kvm_vcpu *vcpu)
 {
-	vcpu->arch.flags &= ~(KVM_ARM64_DEBUG_STATE_SAVE_SPE |
-			      KVM_ARM64_DEBUG_STATE_SAVE_TRBE);
+	vcpu_clear_flag(vcpu, DEBUG_STATE_SAVE_SPE);
+	vcpu_clear_flag(vcpu, DEBUG_STATE_SAVE_TRBE);
 }
diff --git a/arch/arm64/kvm/fpsimd.c b/arch/arm64/kvm/fpsimd.c
index 5621020b28de..ec8e4494873d 100644
--- a/arch/arm64/kvm/fpsimd.c
+++ b/arch/arm64/kvm/fpsimd.c
@@ -7,7 +7,6 @@
  */
 #include <linux/irqflags.h>
 #include <linux/sched.h>
-#include <linux/thread_info.h>
 #include <linux/kvm_host.h>
 #include <asm/fpsimd.h>
 #include <asm/kvm_asm.h>
@@ -15,6 +14,19 @@
 #include <asm/kvm_mmu.h>
 #include <asm/sysreg.h>
 
+void kvm_vcpu_unshare_task_fp(struct kvm_vcpu *vcpu)
+{
+	struct task_struct *p = vcpu->arch.parent_task;
+	struct user_fpsimd_state *fpsimd;
+
+	if (!is_protected_kvm_enabled() || !p)
+		return;
+
+	fpsimd = &p->thread.uw.fpsimd_state;
+	kvm_unshare_hyp(fpsimd, fpsimd + 1);
+	put_task_struct(p);
+}
+
 /*
  * Called on entry to KVM_RUN unless this vcpu previously ran at least
  * once and the most recent prior KVM_RUN for this vcpu was called from
@@ -28,36 +40,29 @@ int kvm_arch_vcpu_run_map_fp(struct kvm_vcpu *vcpu)
 {
 	int ret;
 
-	struct thread_info *ti = &current->thread_info;
 	struct user_fpsimd_state *fpsimd = &current->thread.uw.fpsimd_state;
 
-	/*
-	 * Make sure the host task thread flags and fpsimd state are
-	 * visible to hyp:
-	 */
-	ret = create_hyp_mappings(ti, ti + 1, PAGE_HYP);
-	if (ret)
-		goto error;
+	kvm_vcpu_unshare_task_fp(vcpu);
 
-	ret = create_hyp_mappings(fpsimd, fpsimd + 1, PAGE_HYP);
+	/* Make sure the host task fpsimd state is visible to hyp: */
+	ret = kvm_share_hyp(fpsimd, fpsimd + 1);
 	if (ret)
-		goto error;
+		return ret;
 
-	if (vcpu->arch.sve_state) {
-		void *sve_end;
-
-		sve_end = vcpu->arch.sve_state + vcpu_sve_state_size(vcpu);
+	vcpu->arch.host_fpsimd_state = kern_hyp_va(fpsimd);
 
-		ret = create_hyp_mappings(vcpu->arch.sve_state, sve_end,
-					  PAGE_HYP);
-		if (ret)
-			goto error;
+	/*
+	 * We need to keep current's task_struct pinned until its data has been
+	 * unshared with the hypervisor to make sure it is not re-used by the
+	 * kernel and donated to someone else while already shared -- see
+	 * kvm_vcpu_unshare_task_fp() for the matching put_task_struct().
+	 */
+	if (is_protected_kvm_enabled()) {
+		get_task_struct(current);
+		vcpu->arch.parent_task = current;
 	}
 
-	vcpu->arch.host_thread_info = kern_hyp_va(ti);
-	vcpu->arch.host_fpsimd_state = kern_hyp_va(fpsimd);
-error:
-	return ret;
+	return 0;
 }
 
 /*
@@ -66,40 +71,75 @@ error:
  *
  * Here, we just set the correct metadata to indicate that the FPSIMD
  * state in the cpu regs (if any) belongs to current on the host.
- *
- * TIF_SVE is backed up here, since it may get clobbered with guest state.
- * This flag is restored by kvm_arch_vcpu_put_fp(vcpu).
  */
 void kvm_arch_vcpu_load_fp(struct kvm_vcpu *vcpu)
 {
 	BUG_ON(!current->mm);
+	BUG_ON(test_thread_flag(TIF_SVE));
 
-	vcpu->arch.flags &= ~(KVM_ARM64_FP_ENABLED |
-			      KVM_ARM64_HOST_SVE_IN_USE |
-			      KVM_ARM64_HOST_SVE_ENABLED);
-	vcpu->arch.flags |= KVM_ARM64_FP_HOST;
+	if (!system_supports_fpsimd())
+		return;
 
-	if (test_thread_flag(TIF_SVE))
-		vcpu->arch.flags |= KVM_ARM64_HOST_SVE_IN_USE;
+	vcpu->arch.fp_state = FP_STATE_HOST_OWNED;
 
+	vcpu_clear_flag(vcpu, HOST_SVE_ENABLED);
 	if (read_sysreg(cpacr_el1) & CPACR_EL1_ZEN_EL0EN)
-		vcpu->arch.flags |= KVM_ARM64_HOST_SVE_ENABLED;
+		vcpu_set_flag(vcpu, HOST_SVE_ENABLED);
+
+	/*
+	 * We don't currently support SME guests but if we leave
+	 * things in streaming mode then when the guest starts running
+	 * FPSIMD or SVE code it may generate SME traps so as a
+	 * special case if we are in streaming mode we force the host
+	 * state to be saved now and exit streaming mode so that we
+	 * don't have to handle any SME traps for valid guest
+	 * operations. Do this for ZA as well for now for simplicity.
+	 */
+	if (system_supports_sme()) {
+		vcpu_clear_flag(vcpu, HOST_SME_ENABLED);
+		if (read_sysreg(cpacr_el1) & CPACR_EL1_SMEN_EL0EN)
+			vcpu_set_flag(vcpu, HOST_SME_ENABLED);
+
+		if (read_sysreg_s(SYS_SVCR) & (SVCR_SM_MASK | SVCR_ZA_MASK)) {
+			vcpu->arch.fp_state = FP_STATE_FREE;
+			fpsimd_save_and_flush_cpu_state();
+		}
+	}
+}
+
+/*
+ * Called just before entering the guest once we are no longer preemptable
+ * and interrupts are disabled. If we have managed to run anything using
+ * FP while we were preemptible (such as off the back of an interrupt),
+ * then neither the host nor the guest own the FP hardware (and it was the
+ * responsibility of the code that used FP to save the existing state).
+ */
+void kvm_arch_vcpu_ctxflush_fp(struct kvm_vcpu *vcpu)
+{
+	if (test_thread_flag(TIF_FOREIGN_FPSTATE))
+		vcpu->arch.fp_state = FP_STATE_FREE;
 }
 
 /*
- * If the guest FPSIMD state was loaded, update the host's context
- * tracking data mark the CPU FPSIMD regs as dirty and belonging to vcpu
- * so that they will be written back if the kernel clobbers them due to
- * kernel-mode NEON before re-entry into the guest.
+ * Called just after exiting the guest. If the guest FPSIMD state
+ * was loaded, update the host's context tracking data mark the CPU
+ * FPSIMD regs as dirty and belonging to vcpu so that they will be
+ * written back if the kernel clobbers them due to kernel-mode NEON
+ * before re-entry into the guest.
  */
 void kvm_arch_vcpu_ctxsync_fp(struct kvm_vcpu *vcpu)
 {
 	WARN_ON_ONCE(!irqs_disabled());
 
-	if (vcpu->arch.flags & KVM_ARM64_FP_ENABLED) {
+	if (vcpu->arch.fp_state == FP_STATE_GUEST_OWNED) {
+		/*
+		 * Currently we do not support SME guests so SVCR is
+		 * always 0 and we just need a variable to point to.
+		 */
 		fpsimd_bind_state_to_cpu(&vcpu->arch.ctxt.fp_regs,
 					 vcpu->arch.sve_state,
-					 vcpu->arch.sve_max_vl);
+					 vcpu->arch.sve_max_vl,
+					 NULL, 0, &vcpu->arch.svcr);
 
 		clear_thread_flag(TIF_FOREIGN_FPSTATE);
 		update_thread_flag(TIF_SVE, vcpu_has_sve(vcpu));
@@ -115,13 +155,27 @@ void kvm_arch_vcpu_ctxsync_fp(struct kvm_vcpu *vcpu)
 void kvm_arch_vcpu_put_fp(struct kvm_vcpu *vcpu)
 {
 	unsigned long flags;
-	bool host_has_sve = system_supports_sve();
-	bool guest_has_sve = vcpu_has_sve(vcpu);
 
 	local_irq_save(flags);
 
-	if (vcpu->arch.flags & KVM_ARM64_FP_ENABLED) {
-		if (guest_has_sve) {
+	/*
+	 * If we have VHE then the Hyp code will reset CPACR_EL1 to
+	 * CPACR_EL1_DEFAULT and we need to reenable SME.
+	 */
+	if (has_vhe() && system_supports_sme()) {
+		/* Also restore EL0 state seen on entry */
+		if (vcpu_get_flag(vcpu, HOST_SME_ENABLED))
+			sysreg_clear_set(CPACR_EL1, 0,
+					 CPACR_EL1_SMEN_EL0EN |
+					 CPACR_EL1_SMEN_EL1EN);
+		else
+			sysreg_clear_set(CPACR_EL1,
+					 CPACR_EL1_SMEN_EL0EN,
+					 CPACR_EL1_SMEN_EL1EN);
+	}
+
+	if (vcpu->arch.fp_state == FP_STATE_GUEST_OWNED) {
+		if (vcpu_has_sve(vcpu)) {
 			__vcpu_sys_reg(vcpu, ZCR_EL1) = read_sysreg_el1(SYS_ZCR);
 
 			/* Restore the VL that was saved when bound to the CPU */
@@ -131,7 +185,7 @@ void kvm_arch_vcpu_put_fp(struct kvm_vcpu *vcpu)
 		}
 
 		fpsimd_save_and_flush_cpu_state();
-	} else if (has_vhe() && host_has_sve) {
+	} else if (has_vhe() && system_supports_sve()) {
 		/*
 		 * The FPSIMD/SVE state in the CPU has not been touched, and we
 		 * have SVE (and VHE): CPACR_EL1 (alias CPTR_EL2) has been
@@ -139,14 +193,13 @@ void kvm_arch_vcpu_put_fp(struct kvm_vcpu *vcpu)
 		 * for EL0.  To avoid spurious traps, restore the trap state
 		 * seen by kvm_arch_vcpu_load_fp():
 		 */
-		if (vcpu->arch.flags & KVM_ARM64_HOST_SVE_ENABLED)
+		if (vcpu_get_flag(vcpu, HOST_SVE_ENABLED))
 			sysreg_clear_set(CPACR_EL1, 0, CPACR_EL1_ZEN_EL0EN);
 		else
 			sysreg_clear_set(CPACR_EL1, CPACR_EL1_ZEN_EL0EN, 0);
 	}
 
-	update_thread_flag(TIF_SVE,
-			   vcpu->arch.flags & KVM_ARM64_HOST_SVE_IN_USE);
+	update_thread_flag(TIF_SVE, 0);
 
 	local_irq_restore(flags);
 }
diff --git a/arch/arm64/kvm/guest.c b/arch/arm64/kvm/guest.c
index e116c7767730..2ff13a3f8479 100644
--- a/arch/arm64/kvm/guest.c
+++ b/arch/arm64/kvm/guest.c
@@ -18,7 +18,7 @@
 #include <linux/string.h>
 #include <linux/vmalloc.h>
 #include <linux/fs.h>
-#include <kvm/arm_psci.h>
+#include <kvm/arm_hypercalls.h>
 #include <asm/cputype.h>
 #include <linux/uaccess.h>
 #include <asm/fpsimd.h>
@@ -242,7 +242,7 @@ static int set_core_reg(struct kvm_vcpu *vcpu, const struct kvm_one_reg *reg)
 		u64 mode = (*(u64 *)valp) & PSR_AA32_MODE_MASK;
 		switch (mode) {
 		case PSR_AA32_MODE_USR:
-			if (!system_supports_32bit_el0())
+			if (!kvm_supports_32bit_el0())
 				return -EINVAL;
 			break;
 		case PSR_AA32_MODE_FIQ:
@@ -282,7 +282,7 @@ static int set_core_reg(struct kvm_vcpu *vcpu, const struct kvm_one_reg *reg)
 			break;
 
 		/*
-		 * Otherwide, this is a priviledged mode, and *all* the
+		 * Otherwise, this is a privileged mode, and *all* the
 		 * registers must be narrowed to 32bit.
 		 */
 		default:
@@ -756,7 +756,9 @@ int kvm_arm_get_reg(struct kvm_vcpu *vcpu, const struct kvm_one_reg *reg)
 
 	switch (reg->id & KVM_REG_ARM_COPROC_MASK) {
 	case KVM_REG_ARM_CORE:	return get_core_reg(vcpu, reg);
-	case KVM_REG_ARM_FW:	return kvm_arm_get_fw_reg(vcpu, reg);
+	case KVM_REG_ARM_FW:
+	case KVM_REG_ARM_FW_FEAT_BMAP:
+		return kvm_arm_get_fw_reg(vcpu, reg);
 	case KVM_REG_ARM64_SVE:	return get_sve_reg(vcpu, reg);
 	}
 
@@ -774,7 +776,9 @@ int kvm_arm_set_reg(struct kvm_vcpu *vcpu, const struct kvm_one_reg *reg)
 
 	switch (reg->id & KVM_REG_ARM_COPROC_MASK) {
 	case KVM_REG_ARM_CORE:	return set_core_reg(vcpu, reg);
-	case KVM_REG_ARM_FW:	return kvm_arm_set_fw_reg(vcpu, reg);
+	case KVM_REG_ARM_FW:
+	case KVM_REG_ARM_FW_FEAT_BMAP:
+		return kvm_arm_set_fw_reg(vcpu, reg);
 	case KVM_REG_ARM64_SVE:	return set_sve_reg(vcpu, reg);
 	}
 
@@ -933,6 +937,7 @@ int kvm_arch_vcpu_ioctl_set_guest_debug(struct kvm_vcpu *vcpu,
 	} else {
 		/* If not enabled clear all flags */
 		vcpu->guest_debug = 0;
+		vcpu_clear_flag(vcpu, DBG_SS_ACTIVE_PENDING);
 	}
 
 out:
diff --git a/arch/arm64/kvm/handle_exit.c b/arch/arm64/kvm/handle_exit.c
index 275a27368a04..e778eefcf214 100644
--- a/arch/arm64/kvm/handle_exit.c
+++ b/arch/arm64/kvm/handle_exit.c
@@ -17,6 +17,7 @@
 #include <asm/kvm_emulate.h>
 #include <asm/kvm_mmu.h>
 #include <asm/debug-monitors.h>
+#include <asm/stacktrace/nvhe.h>
 #include <asm/traps.h>
 
 #include <kvm/arm_hypercalls.h>
@@ -26,7 +27,7 @@
 
 typedef int (*exit_handle_fn)(struct kvm_vcpu *);
 
-static void kvm_handle_guest_serror(struct kvm_vcpu *vcpu, u32 esr)
+static void kvm_handle_guest_serror(struct kvm_vcpu *vcpu, u64 esr)
 {
 	if (!arm64_is_ras_serror(esr) || arm64_is_fatal_ras_serror(NULL, esr))
 		kvm_inject_vabt(vcpu);
@@ -80,25 +81,51 @@ static int handle_no_fpsimd(struct kvm_vcpu *vcpu)
  *
  * @vcpu:	the vcpu pointer
  *
- * WFE: Yield the CPU and come back to this vcpu when the scheduler
+ * WFE[T]: Yield the CPU and come back to this vcpu when the scheduler
  * decides to.
- * WFI: Simply call kvm_vcpu_block(), which will halt execution of
+ * WFI: Simply call kvm_vcpu_halt(), which will halt execution of
  * world-switches and schedule other host processes until there is an
  * incoming IRQ or FIQ to the VM.
+ * WFIT: Same as WFI, with a timed wakeup implemented as a background timer
+ *
+ * WF{I,E}T can immediately return if the deadline has already expired.
  */
 static int kvm_handle_wfx(struct kvm_vcpu *vcpu)
 {
-	if (kvm_vcpu_get_esr(vcpu) & ESR_ELx_WFx_ISS_WFE) {
+	u64 esr = kvm_vcpu_get_esr(vcpu);
+
+	if (esr & ESR_ELx_WFx_ISS_WFE) {
 		trace_kvm_wfx_arm64(*vcpu_pc(vcpu), true);
 		vcpu->stat.wfe_exit_stat++;
-		kvm_vcpu_on_spin(vcpu, vcpu_mode_priv(vcpu));
 	} else {
 		trace_kvm_wfx_arm64(*vcpu_pc(vcpu), false);
 		vcpu->stat.wfi_exit_stat++;
-		kvm_vcpu_block(vcpu);
-		kvm_clear_request(KVM_REQ_UNHALT, vcpu);
 	}
 
+	if (esr & ESR_ELx_WFx_ISS_WFxT) {
+		if (esr & ESR_ELx_WFx_ISS_RV) {
+			u64 val, now;
+
+			now = kvm_arm_timer_get_reg(vcpu, KVM_REG_ARM_TIMER_CNT);
+			val = vcpu_get_reg(vcpu, kvm_vcpu_sys_get_rt(vcpu));
+
+			if (now >= val)
+				goto out;
+		} else {
+			/* Treat WFxT as WFx if RN is invalid */
+			esr &= ~ESR_ELx_WFx_ISS_WFxT;
+		}
+	}
+
+	if (esr & ESR_ELx_WFx_ISS_WFE) {
+		kvm_vcpu_on_spin(vcpu, vcpu_mode_priv(vcpu));
+	} else {
+		if (esr & ESR_ELx_WFx_ISS_WFxT)
+			vcpu_set_flag(vcpu, IN_WFIT);
+
+		kvm_vcpu_wfi(vcpu);
+	}
+out:
 	kvm_incr_pc(vcpu);
 
 	return 1;
@@ -118,31 +145,42 @@ static int kvm_handle_wfx(struct kvm_vcpu *vcpu)
 static int kvm_handle_guest_debug(struct kvm_vcpu *vcpu)
 {
 	struct kvm_run *run = vcpu->run;
-	u32 esr = kvm_vcpu_get_esr(vcpu);
+	u64 esr = kvm_vcpu_get_esr(vcpu);
 
 	run->exit_reason = KVM_EXIT_DEBUG;
-	run->debug.arch.hsr = esr;
+	run->debug.arch.hsr = lower_32_bits(esr);
+	run->debug.arch.hsr_high = upper_32_bits(esr);
+	run->flags = KVM_DEBUG_ARCH_HSR_HIGH_VALID;
 
-	if (ESR_ELx_EC(esr) == ESR_ELx_EC_WATCHPT_LOW)
+	switch (ESR_ELx_EC(esr)) {
+	case ESR_ELx_EC_WATCHPT_LOW:
 		run->debug.arch.far = vcpu->arch.fault.far_el2;
+		break;
+	case ESR_ELx_EC_SOFTSTP_LOW:
+		vcpu_clear_flag(vcpu, DBG_SS_ACTIVE_PENDING);
+		break;
+	}
 
 	return 0;
 }
 
 static int kvm_handle_unknown_ec(struct kvm_vcpu *vcpu)
 {
-	u32 esr = kvm_vcpu_get_esr(vcpu);
+	u64 esr = kvm_vcpu_get_esr(vcpu);
 
-	kvm_pr_unimpl("Unknown exception class: esr: %#08x -- %s\n",
+	kvm_pr_unimpl("Unknown exception class: esr: %#016llx -- %s\n",
 		      esr, esr_get_class_string(esr));
 
 	kvm_inject_undefined(vcpu);
 	return 1;
 }
 
+/*
+ * Guest access to SVE registers should be routed to this handler only
+ * when the system doesn't support SVE.
+ */
 static int handle_sve(struct kvm_vcpu *vcpu)
 {
-	/* Until SVE is supported for guests: */
 	kvm_inject_undefined(vcpu);
 	return 1;
 }
@@ -165,6 +203,7 @@ static exit_handle_fn arm_exit_handlers[] = {
 	[ESR_ELx_EC_CP15_64]	= kvm_handle_cp15_64,
 	[ESR_ELx_EC_CP14_MR]	= kvm_handle_cp14_32,
 	[ESR_ELx_EC_CP14_LS]	= kvm_handle_cp14_load_store,
+	[ESR_ELx_EC_CP10_ID]	= kvm_handle_cp10_id,
 	[ESR_ELx_EC_CP14_64]	= kvm_handle_cp14_64,
 	[ESR_ELx_EC_HVC32]	= handle_hvc,
 	[ESR_ELx_EC_SMC32]	= handle_smc,
@@ -185,7 +224,7 @@ static exit_handle_fn arm_exit_handlers[] = {
 
 static exit_handle_fn kvm_get_exit_handler(struct kvm_vcpu *vcpu)
 {
-	u32 esr = kvm_vcpu_get_esr(vcpu);
+	u64 esr = kvm_vcpu_get_esr(vcpu);
 	u8 esr_ec = ESR_ELx_EC(esr);
 
 	return arm_exit_handlers[esr_ec];
@@ -226,6 +265,14 @@ int handle_exit(struct kvm_vcpu *vcpu, int exception_index)
 {
 	struct kvm_run *run = vcpu->run;
 
+	if (ARM_SERROR_PENDING(exception_index)) {
+		/*
+		 * The SError is handled by handle_exit_early(). If the guest
+		 * survives it will re-execute the original instruction.
+		 */
+		return 1;
+	}
+
 	exception_index = ARM_EXCEPTION_CODE(exception_index);
 
 	switch (exception_index) {
@@ -238,7 +285,7 @@ int handle_exit(struct kvm_vcpu *vcpu, int exception_index)
 	case ARM_EXCEPTION_HYP_GONE:
 		/*
 		 * EL2 has been reset to the hyp-stub. This happens when a guest
-		 * is pre-empted by kvm_reboot()'s shutdown call.
+		 * is pre-emptied by kvm_reboot()'s shutdown call.
 		 */
 		run->exit_reason = KVM_EXIT_FAIL_ENTRY;
 		return 0;
@@ -285,13 +332,8 @@ void __noreturn __cold nvhe_hyp_panic_handler(u64 esr, u64 spsr,
 	u64 elr_in_kimg = __phys_to_kimg(elr_phys);
 	u64 hyp_offset = elr_in_kimg - kaslr_offset() - elr_virt;
 	u64 mode = spsr & PSR_MODE_MASK;
+	u64 panic_addr = elr_virt + hyp_offset;
 
-	/*
-	 * The nVHE hyp symbols are not included by kallsyms to avoid issues
-	 * with aliasing. That means that the symbols cannot be printed with the
-	 * "%pS" format specifier, so fall back to the vmlinux address if
-	 * there's no better option.
-	 */
 	if (mode != PSR_MODE_EL2t && mode != PSR_MODE_EL2h) {
 		kvm_err("Invalid host exception to nVHE hyp!\n");
 	} else if (ESR_ELx_EC(esr) == ESR_ELx_EC_BRK64 &&
@@ -311,11 +353,16 @@ void __noreturn __cold nvhe_hyp_panic_handler(u64 esr, u64 spsr,
 		if (file)
 			kvm_err("nVHE hyp BUG at: %s:%u!\n", file, line);
 		else
-			kvm_err("nVHE hyp BUG at: %016llx!\n", elr_virt + hyp_offset);
+			kvm_err("nVHE hyp BUG at: [<%016llx>] %pB!\n", panic_addr,
+					(void *)(panic_addr + kaslr_offset()));
 	} else {
-		kvm_err("nVHE hyp panic at: %016llx!\n", elr_virt + hyp_offset);
+		kvm_err("nVHE hyp panic at: [<%016llx>] %pB!\n", panic_addr,
+				(void *)(panic_addr + kaslr_offset()));
 	}
 
+	/* Dump the nVHE hypervisor backtrace */
+	kvm_nvhe_dump_backtrace(hyp_offset);
+
 	/*
 	 * Hyp has panicked and we're going to handle that by panicking the
 	 * kernel. The kernel offset will be revealed in the panic so we're
@@ -324,6 +371,6 @@ void __noreturn __cold nvhe_hyp_panic_handler(u64 esr, u64 spsr,
 	 */
 	kvm_err("Hyp Offset: 0x%llx\n", hyp_offset);
 
-	panic("HYP panic:\nPS:%08llx PC:%016llx ESR:%08llx\nFAR:%016llx HPFAR:%016llx PAR:%016llx\nVCPU:%016lx\n",
+	panic("HYP panic:\nPS:%08llx PC:%016llx ESR:%016llx\nFAR:%016llx HPFAR:%016llx PAR:%016llx\nVCPU:%016lx\n",
 	      spsr, elr_virt, esr, far, hpfar, par, vcpu);
 }
diff --git a/arch/arm64/kvm/hyp/Makefile b/arch/arm64/kvm/hyp/Makefile
index b726332eec49..a38dea6186c9 100644
--- a/arch/arm64/kvm/hyp/Makefile
+++ b/arch/arm64/kvm/hyp/Makefile
@@ -5,9 +5,6 @@
 
 incdir := $(srctree)/$(src)/include
 subdir-asflags-y := -I$(incdir)
-subdir-ccflags-y := -I$(incdir)				\
-		    -fno-stack-protector		\
-		    -DDISABLE_BRANCH_PROFILING		\
-		    $(DISABLE_STACKLEAK_PLUGIN)
+subdir-ccflags-y := -I$(incdir)
 
-obj-$(CONFIG_KVM) += vhe/ nvhe/ pgtable.o reserved_mem.o
+obj-$(CONFIG_KVM) += vhe/ nvhe/ pgtable.o
diff --git a/arch/arm64/kvm/hyp/exception.c b/arch/arm64/kvm/hyp/exception.c
index 0418399e0a20..791d3de76771 100644
--- a/arch/arm64/kvm/hyp/exception.c
+++ b/arch/arm64/kvm/hyp/exception.c
@@ -13,6 +13,7 @@
 #include <hyp/adjust_pc.h>
 #include <linux/kvm_host.h>
 #include <asm/kvm_emulate.h>
+#include <asm/kvm_mmu.h>
 
 #if !defined (__KVM_NVHE_HYPERVISOR__) && !defined (__KVM_VHE_HYPERVISOR__)
 #error Hypervisor code only!
@@ -38,7 +39,10 @@ static inline void __vcpu_write_sys_reg(struct kvm_vcpu *vcpu, u64 val, int reg)
 
 static void __vcpu_write_spsr(struct kvm_vcpu *vcpu, u64 val)
 {
-	write_sysreg_el1(val, SYS_SPSR);
+	if (has_vhe())
+		write_sysreg_el1(val, SYS_SPSR);
+	else
+		__vcpu_sys_reg(vcpu, SPSR_EL1) = val;
 }
 
 static void __vcpu_write_spsr_abt(struct kvm_vcpu *vcpu, u64 val)
@@ -112,7 +116,7 @@ static void enter_exception64(struct kvm_vcpu *vcpu, unsigned long target_mode,
 	new |= (old & PSR_C_BIT);
 	new |= (old & PSR_V_BIT);
 
-	if (kvm_has_mte(vcpu->kvm))
+	if (kvm_has_mte(kern_hyp_va(vcpu->kvm)))
 		new |= PSR_TCO_BIT;
 
 	new |= (old & PSR_DIT_BIT);
@@ -300,14 +304,14 @@ static void enter_exception32(struct kvm_vcpu *vcpu, u32 mode, u32 vect_offset)
 static void kvm_inject_exception(struct kvm_vcpu *vcpu)
 {
 	if (vcpu_el1_is_32bit(vcpu)) {
-		switch (vcpu->arch.flags & KVM_ARM64_EXCEPT_MASK) {
-		case KVM_ARM64_EXCEPT_AA32_UND:
+		switch (vcpu_get_flag(vcpu, EXCEPT_MASK)) {
+		case unpack_vcpu_flag(EXCEPT_AA32_UND):
 			enter_exception32(vcpu, PSR_AA32_MODE_UND, 4);
 			break;
-		case KVM_ARM64_EXCEPT_AA32_IABT:
+		case unpack_vcpu_flag(EXCEPT_AA32_IABT):
 			enter_exception32(vcpu, PSR_AA32_MODE_ABT, 12);
 			break;
-		case KVM_ARM64_EXCEPT_AA32_DABT:
+		case unpack_vcpu_flag(EXCEPT_AA32_DABT):
 			enter_exception32(vcpu, PSR_AA32_MODE_ABT, 16);
 			break;
 		default:
@@ -315,9 +319,8 @@ static void kvm_inject_exception(struct kvm_vcpu *vcpu)
 			break;
 		}
 	} else {
-		switch (vcpu->arch.flags & KVM_ARM64_EXCEPT_MASK) {
-		case (KVM_ARM64_EXCEPT_AA64_ELx_SYNC |
-		      KVM_ARM64_EXCEPT_AA64_EL1):
+		switch (vcpu_get_flag(vcpu, EXCEPT_MASK)) {
+		case unpack_vcpu_flag(EXCEPT_AA64_EL1_SYNC):
 			enter_exception64(vcpu, PSR_MODE_EL1h, except_type_sync);
 			break;
 		default:
@@ -337,12 +340,12 @@ static void kvm_inject_exception(struct kvm_vcpu *vcpu)
  */
 void __kvm_adjust_pc(struct kvm_vcpu *vcpu)
 {
-	if (vcpu->arch.flags & KVM_ARM64_PENDING_EXCEPTION) {
+	if (vcpu_get_flag(vcpu, PENDING_EXCEPTION)) {
 		kvm_inject_exception(vcpu);
-		vcpu->arch.flags &= ~(KVM_ARM64_PENDING_EXCEPTION |
-				      KVM_ARM64_EXCEPT_MASK);
-	} else 	if (vcpu->arch.flags & KVM_ARM64_INCREMENT_PC) {
+		vcpu_clear_flag(vcpu, PENDING_EXCEPTION);
+		vcpu_clear_flag(vcpu, EXCEPT_MASK);
+	} else if (vcpu_get_flag(vcpu, INCREMENT_PC)) {
 		kvm_skip_instr(vcpu);
-		vcpu->arch.flags &= ~KVM_ARM64_INCREMENT_PC;
+		vcpu_clear_flag(vcpu, INCREMENT_PC);
 	}
 }
diff --git a/arch/arm64/kvm/hyp/fpsimd.S b/arch/arm64/kvm/hyp/fpsimd.S
index e950875e31ce..61e6f3ba7b7d 100644
--- a/arch/arm64/kvm/hyp/fpsimd.S
+++ b/arch/arm64/kvm/hyp/fpsimd.S
@@ -25,9 +25,3 @@ SYM_FUNC_START(__sve_restore_state)
 	sve_load 0, x1, x2, 3
 	ret
 SYM_FUNC_END(__sve_restore_state)
-
-SYM_FUNC_START(__sve_save_state)
-	mov	x2, #1
-	sve_save 0, x1, x2, 3
-	ret
-SYM_FUNC_END(__sve_save_state)
diff --git a/arch/arm64/kvm/hyp/hyp-constants.c b/arch/arm64/kvm/hyp/hyp-constants.c
new file mode 100644
index 000000000000..b3742a6691e8
--- /dev/null
+++ b/arch/arm64/kvm/hyp/hyp-constants.c
@@ -0,0 +1,10 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+#include <linux/kbuild.h>
+#include <nvhe/memory.h>
+
+int main(void)
+{
+	DEFINE(STRUCT_HYP_PAGE_SIZE,	sizeof(struct hyp_page));
+	return 0;
+}
diff --git a/arch/arm64/kvm/hyp/hyp-entry.S b/arch/arm64/kvm/hyp/hyp-entry.S
index b6b6801d96d5..8f3f93fa119e 100644
--- a/arch/arm64/kvm/hyp/hyp-entry.S
+++ b/arch/arm64/kvm/hyp/hyp-entry.S
@@ -62,6 +62,10 @@ el1_sync:				// Guest trapped into EL2
 	/* ARM_SMCCC_ARCH_WORKAROUND_2 handling */
 	eor	w1, w1, #(ARM_SMCCC_ARCH_WORKAROUND_1 ^ \
 			  ARM_SMCCC_ARCH_WORKAROUND_2)
+	cbz	w1, wa_epilogue
+
+	eor	w1, w1, #(ARM_SMCCC_ARCH_WORKAROUND_2 ^ \
+			  ARM_SMCCC_ARCH_WORKAROUND_3)
 	cbnz	w1, el1_trap
 
 wa_epilogue:
@@ -192,7 +196,10 @@ SYM_CODE_END(__kvm_hyp_vector)
 	sub	sp, sp, #(8 * 4)
 	stp	x2, x3, [sp, #(8 * 0)]
 	stp	x0, x1, [sp, #(8 * 2)]
+	alternative_cb ARM64_ALWAYS_SYSTEM, spectre_bhb_patch_wa3
+	/* Patched to mov WA3 when supported */
 	mov	w0, #ARM_SMCCC_ARCH_WORKAROUND_1
+	alternative_cb_end
 	smc	#0
 	ldp	x2, x3, [sp, #(8 * 0)]
 	add	sp, sp, #(8 * 2)
@@ -205,9 +212,11 @@ SYM_CODE_END(__kvm_hyp_vector)
 	spectrev2_smccc_wa1_smc
 	.else
 	stp	x0, x1, [sp, #-16]!
+	mitigate_spectre_bhb_loop	x0
+	mitigate_spectre_bhb_clear_insn
 	.endif
 	.if \indirect != 0
-	alternative_cb  kvm_patch_vector_branch
+	alternative_cb ARM64_ALWAYS_SYSTEM, kvm_patch_vector_branch
 	/*
 	 * For ARM64_SPECTRE_V3A configurations, these NOPs get replaced with:
 	 *
diff --git a/arch/arm64/kvm/hyp/include/hyp/debug-sr.h b/arch/arm64/kvm/hyp/include/hyp/debug-sr.h
index 4ebe9f558f3a..961bbef104a6 100644
--- a/arch/arm64/kvm/hyp/include/hyp/debug-sr.h
+++ b/arch/arm64/kvm/hyp/include/hyp/debug-sr.h
@@ -132,7 +132,7 @@ static inline void __debug_switch_to_guest_common(struct kvm_vcpu *vcpu)
 	struct kvm_guest_debug_arch *host_dbg;
 	struct kvm_guest_debug_arch *guest_dbg;
 
-	if (!(vcpu->arch.flags & KVM_ARM64_DEBUG_DIRTY))
+	if (!vcpu_get_flag(vcpu, DEBUG_DIRTY))
 		return;
 
 	host_ctxt = &this_cpu_ptr(&kvm_host_data)->host_ctxt;
@@ -151,7 +151,7 @@ static inline void __debug_switch_to_host_common(struct kvm_vcpu *vcpu)
 	struct kvm_guest_debug_arch *host_dbg;
 	struct kvm_guest_debug_arch *guest_dbg;
 
-	if (!(vcpu->arch.flags & KVM_ARM64_DEBUG_DIRTY))
+	if (!vcpu_get_flag(vcpu, DEBUG_DIRTY))
 		return;
 
 	host_ctxt = &this_cpu_ptr(&kvm_host_data)->host_ctxt;
@@ -162,7 +162,7 @@ static inline void __debug_switch_to_host_common(struct kvm_vcpu *vcpu)
 	__debug_save_state(guest_dbg, guest_ctxt);
 	__debug_restore_state(host_dbg, host_ctxt);
 
-	vcpu->arch.flags &= ~KVM_ARM64_DEBUG_DIRTY;
+	vcpu_clear_flag(vcpu, DEBUG_DIRTY);
 }
 
 #endif /* __ARM64_KVM_HYP_DEBUG_SR_H__ */
diff --git a/arch/arm64/kvm/hyp/include/hyp/switch.h b/arch/arm64/kvm/hyp/include/hyp/switch.h
index 96c5f3fb7838..3330d1b76bdd 100644
--- a/arch/arm64/kvm/hyp/include/hyp/switch.h
+++ b/arch/arm64/kvm/hyp/include/hyp/switch.h
@@ -29,7 +29,6 @@
 #include <asm/fpsimd.h>
 #include <asm/debug-monitors.h>
 #include <asm/processor.h>
-#include <asm/thread_info.h>
 
 struct kvm_exception_table_entry {
 	int insn, fixup;
@@ -38,22 +37,10 @@ struct kvm_exception_table_entry {
 extern struct kvm_exception_table_entry __start___kvm_ex_table;
 extern struct kvm_exception_table_entry __stop___kvm_ex_table;
 
-/* Check whether the FP regs were dirtied while in the host-side run loop: */
-static inline bool update_fp_enabled(struct kvm_vcpu *vcpu)
+/* Check whether the FP regs are owned by the guest */
+static inline bool guest_owns_fp_regs(struct kvm_vcpu *vcpu)
 {
-	/*
-	 * When the system doesn't support FP/SIMD, we cannot rely on
-	 * the _TIF_FOREIGN_FPSTATE flag. However, we always inject an
-	 * abort on the very first access to FP and thus we should never
-	 * see KVM_ARM64_FP_ENABLED. For added safety, make sure we always
-	 * trap the accesses.
-	 */
-	if (!system_supports_fpsimd() ||
-	    vcpu->arch.host_thread_info->flags & _TIF_FOREIGN_FPSTATE)
-		vcpu->arch.flags &= ~(KVM_ARM64_FP_ENABLED |
-				      KVM_ARM64_FP_HOST);
-
-	return !!(vcpu->arch.flags & KVM_ARM64_FP_ENABLED);
+	return vcpu->arch.fp_state == FP_STATE_GUEST_OWNED;
 }
 
 /* Save the 32-bit only FPSIMD system register state */
@@ -100,6 +87,17 @@ static inline void __activate_traps_common(struct kvm_vcpu *vcpu)
 
 	vcpu->arch.mdcr_el2_host = read_sysreg(mdcr_el2);
 	write_sysreg(vcpu->arch.mdcr_el2, mdcr_el2);
+
+	if (cpus_have_final_cap(ARM64_SME)) {
+		sysreg_clear_set_s(SYS_HFGRTR_EL2,
+				   HFGxTR_EL2_nSMPRI_EL1_MASK |
+				   HFGxTR_EL2_nTPIDR2_EL0_MASK,
+				   0);
+		sysreg_clear_set_s(SYS_HFGWTR_EL2,
+				   HFGxTR_EL2_nSMPRI_EL1_MASK |
+				   HFGxTR_EL2_nTPIDR2_EL0_MASK,
+				   0);
+	}
 }
 
 static inline void __deactivate_traps_common(struct kvm_vcpu *vcpu)
@@ -109,6 +107,15 @@ static inline void __deactivate_traps_common(struct kvm_vcpu *vcpu)
 	write_sysreg(0, hstr_el2);
 	if (kvm_arm_support_pmu_v3())
 		write_sysreg(0, pmuserenr_el0);
+
+	if (cpus_have_final_cap(ARM64_SME)) {
+		sysreg_clear_set_s(SYS_HFGRTR_EL2, 0,
+				   HFGxTR_EL2_nSMPRI_EL1_MASK |
+				   HFGxTR_EL2_nTPIDR2_EL0_MASK);
+		sysreg_clear_set_s(SYS_HFGWTR_EL2, 0,
+				   HFGxTR_EL2_nSMPRI_EL1_MASK |
+				   HFGxTR_EL2_nTPIDR2_EL0_MASK);
+	}
 }
 
 static inline void ___activate_traps(struct kvm_vcpu *vcpu)
@@ -143,16 +150,6 @@ static inline bool __populate_fault_info(struct kvm_vcpu *vcpu)
 	return __get_fault_info(vcpu->arch.fault.esr_el2, &vcpu->arch.fault);
 }
 
-static inline void __hyp_sve_save_host(struct kvm_vcpu *vcpu)
-{
-	struct thread_struct *thread;
-
-	thread = container_of(vcpu->arch.host_fpsimd_state, struct thread_struct,
-			      uw.fpsimd_state);
-
-	__sve_save_state(sve_pffr(thread), &vcpu->arch.host_fpsimd_state->fpsr);
-}
-
 static inline void __hyp_sve_restore_guest(struct kvm_vcpu *vcpu)
 {
 	sve_cond_update_zcr_vq(vcpu_sve_max_vq(vcpu) - 1, SYS_ZCR_EL2);
@@ -169,21 +166,14 @@ static inline void __hyp_sve_restore_guest(struct kvm_vcpu *vcpu)
  */
 static bool kvm_hyp_handle_fpsimd(struct kvm_vcpu *vcpu, u64 *exit_code)
 {
-	bool sve_guest, sve_host;
+	bool sve_guest;
 	u8 esr_ec;
 	u64 reg;
 
 	if (!system_supports_fpsimd())
 		return false;
 
-	if (system_supports_sve()) {
-		sve_guest = vcpu_has_sve(vcpu);
-		sve_host = vcpu->arch.flags & KVM_ARM64_HOST_SVE_IN_USE;
-	} else {
-		sve_guest = false;
-		sve_host = false;
-	}
-
+	sve_guest = vcpu_has_sve(vcpu);
 	esr_ec = kvm_vcpu_trap_get_class(vcpu);
 
 	/* Don't handle SVE traps for non-SVE vcpus here: */
@@ -191,10 +181,12 @@ static bool kvm_hyp_handle_fpsimd(struct kvm_vcpu *vcpu, u64 *exit_code)
 		return false;
 
 	/* Valid trap.  Switch the context: */
+
+	/* First disable enough traps to allow us to update the registers */
 	if (has_vhe()) {
-		reg = CPACR_EL1_FPEN;
+		reg = CPACR_EL1_FPEN_EL0EN | CPACR_EL1_FPEN_EL1EN;
 		if (sve_guest)
-			reg |= CPACR_EL1_ZEN;
+			reg |= CPACR_EL1_ZEN_EL0EN | CPACR_EL1_ZEN_EL1EN;
 
 		sysreg_clear_set(cpacr_el1, 0, reg);
 	} else {
@@ -206,15 +198,11 @@ static bool kvm_hyp_handle_fpsimd(struct kvm_vcpu *vcpu, u64 *exit_code)
 	}
 	isb();
 
-	if (vcpu->arch.flags & KVM_ARM64_FP_HOST) {
-		if (sve_host)
-			__hyp_sve_save_host(vcpu);
-		else
-			__fpsimd_save_state(vcpu->arch.host_fpsimd_state);
-
-		vcpu->arch.flags &= ~KVM_ARM64_FP_HOST;
-	}
+	/* Write out the host state if it's in the registers */
+	if (vcpu->arch.fp_state == FP_STATE_HOST_OWNED)
+		__fpsimd_save_state(vcpu->arch.host_fpsimd_state);
 
+	/* Restore the guest state */
 	if (sve_guest)
 		__hyp_sve_restore_guest(vcpu);
 	else
@@ -224,7 +212,7 @@ static bool kvm_hyp_handle_fpsimd(struct kvm_vcpu *vcpu, u64 *exit_code)
 	if (!(read_sysreg(hcr_el2) & HCR_RW))
 		write_sysreg(__vcpu_sys_reg(vcpu, FPEXC32_EL2), fpexc32_el2);
 
-	vcpu->arch.flags |= KVM_ARM64_FP_ENABLED;
+	vcpu->arch.fp_state = FP_STATE_GUEST_OWNED;
 
 	return true;
 }
@@ -284,7 +272,7 @@ static inline bool handle_tx2_tvm(struct kvm_vcpu *vcpu)
 	return true;
 }
 
-static inline bool esr_is_ptrauth_trap(u32 esr)
+static inline bool esr_is_ptrauth_trap(u64 esr)
 {
 	switch (esr_sys64_to_sysreg(esr)) {
 	case SYS_APIAKEYLO_EL1:
@@ -424,6 +412,24 @@ static inline bool kvm_hyp_handle_exit(struct kvm_vcpu *vcpu, u64 *exit_code)
 	return false;
 }
 
+static inline void synchronize_vcpu_pstate(struct kvm_vcpu *vcpu, u64 *exit_code)
+{
+	/*
+	 * Check for the conditions of Cortex-A510's #2077057. When these occur
+	 * SPSR_EL2 can't be trusted, but isn't needed either as it is
+	 * unchanged from the value in vcpu_gp_regs(vcpu)->pstate.
+	 * Are we single-stepping the guest, and took a PAC exception from the
+	 * active-not-pending state?
+	 */
+	if (cpus_have_final_cap(ARM64_WORKAROUND_2077057)		&&
+	    vcpu->guest_debug & KVM_GUESTDBG_SINGLESTEP			&&
+	    *vcpu_cpsr(vcpu) & DBG_SPSR_SS				&&
+	    ESR_ELx_EC(read_sysreg_el2(SYS_ESR)) == ESR_ELx_EC_PAC)
+		write_sysreg_el2(*vcpu_cpsr(vcpu), SYS_SPSR);
+
+	vcpu->arch.ctxt.regs.pstate = read_sysreg_el2(SYS_SPSR);
+}
+
 /*
  * Return true when we were able to fixup the guest exit and should return to
  * the guest, false when we should restore the host state and return to the
@@ -435,7 +441,7 @@ static inline bool fixup_guest_exit(struct kvm_vcpu *vcpu, u64 *exit_code)
 	 * Save PSTATE early so that we can evaluate the vcpu mode
 	 * early on.
 	 */
-	vcpu->arch.ctxt.regs.pstate = read_sysreg_el2(SYS_SPSR);
+	synchronize_vcpu_pstate(vcpu, exit_code);
 
 	/*
 	 * Check whether we want to repaint the state one way or
@@ -446,7 +452,8 @@ static inline bool fixup_guest_exit(struct kvm_vcpu *vcpu, u64 *exit_code)
 	if (ARM_EXCEPTION_CODE(*exit_code) != ARM_EXCEPTION_IRQ)
 		vcpu->arch.fault.esr_el2 = read_sysreg_el2(SYS_ESR);
 
-	if (ARM_SERROR_PENDING(*exit_code)) {
+	if (ARM_SERROR_PENDING(*exit_code) &&
+	    ARM_EXCEPTION_CODE(*exit_code) != ARM_EXCEPTION_IRQ) {
 		u8 esr_ec = kvm_vcpu_trap_get_class(vcpu);
 
 		/*
diff --git a/arch/arm64/kvm/hyp/include/hyp/sysreg-sr.h b/arch/arm64/kvm/hyp/include/hyp/sysreg-sr.h
index 7ecca8b07851..baa5b9b3dde5 100644
--- a/arch/arm64/kvm/hyp/include/hyp/sysreg-sr.h
+++ b/arch/arm64/kvm/hyp/include/hyp/sysreg-sr.h
@@ -195,7 +195,7 @@ static inline void __sysreg32_save_state(struct kvm_vcpu *vcpu)
 	__vcpu_sys_reg(vcpu, DACR32_EL2) = read_sysreg(dacr32_el2);
 	__vcpu_sys_reg(vcpu, IFSR32_EL2) = read_sysreg(ifsr32_el2);
 
-	if (has_vhe() || vcpu->arch.flags & KVM_ARM64_DEBUG_DIRTY)
+	if (has_vhe() || vcpu_get_flag(vcpu, DEBUG_DIRTY))
 		__vcpu_sys_reg(vcpu, DBGVCR32_EL2) = read_sysreg(dbgvcr32_el2);
 }
 
@@ -212,7 +212,7 @@ static inline void __sysreg32_restore_state(struct kvm_vcpu *vcpu)
 	write_sysreg(__vcpu_sys_reg(vcpu, DACR32_EL2), dacr32_el2);
 	write_sysreg(__vcpu_sys_reg(vcpu, IFSR32_EL2), ifsr32_el2);
 
-	if (has_vhe() || vcpu->arch.flags & KVM_ARM64_DEBUG_DIRTY)
+	if (has_vhe() || vcpu_get_flag(vcpu, DEBUG_DIRTY))
 		write_sysreg(__vcpu_sys_reg(vcpu, DBGVCR32_EL2), dbgvcr32_el2);
 }
 
diff --git a/arch/arm64/kvm/hyp/include/nvhe/fixed_config.h b/arch/arm64/kvm/hyp/include/nvhe/fixed_config.h
index eea1f6a53723..07edfc7524c9 100644
--- a/arch/arm64/kvm/hyp/include/nvhe/fixed_config.h
+++ b/arch/arm64/kvm/hyp/include/nvhe/fixed_config.h
@@ -35,9 +35,9 @@
  * - Data Independent Timing
  */
 #define PVM_ID_AA64PFR0_ALLOW (\
-	ARM64_FEATURE_MASK(ID_AA64PFR0_FP) | \
-	ARM64_FEATURE_MASK(ID_AA64PFR0_ASIMD) | \
-	ARM64_FEATURE_MASK(ID_AA64PFR0_DIT) \
+	ARM64_FEATURE_MASK(ID_AA64PFR0_EL1_FP) | \
+	ARM64_FEATURE_MASK(ID_AA64PFR0_EL1_AdvSIMD) | \
+	ARM64_FEATURE_MASK(ID_AA64PFR0_EL1_DIT) \
 	)
 
 /*
@@ -49,11 +49,11 @@
  *	Supported by KVM
  */
 #define PVM_ID_AA64PFR0_RESTRICT_UNSIGNED (\
-	FIELD_PREP(ARM64_FEATURE_MASK(ID_AA64PFR0_EL0), ID_AA64PFR0_ELx_64BIT_ONLY) | \
-	FIELD_PREP(ARM64_FEATURE_MASK(ID_AA64PFR0_EL1), ID_AA64PFR0_ELx_64BIT_ONLY) | \
-	FIELD_PREP(ARM64_FEATURE_MASK(ID_AA64PFR0_EL2), ID_AA64PFR0_ELx_64BIT_ONLY) | \
-	FIELD_PREP(ARM64_FEATURE_MASK(ID_AA64PFR0_EL3), ID_AA64PFR0_ELx_64BIT_ONLY) | \
-	FIELD_PREP(ARM64_FEATURE_MASK(ID_AA64PFR0_RAS), ID_AA64PFR0_RAS_V1) \
+	FIELD_PREP(ARM64_FEATURE_MASK(ID_AA64PFR0_EL1_EL0), ID_AA64PFR0_EL1_ELx_64BIT_ONLY) | \
+	FIELD_PREP(ARM64_FEATURE_MASK(ID_AA64PFR0_EL1_EL1), ID_AA64PFR0_EL1_ELx_64BIT_ONLY) | \
+	FIELD_PREP(ARM64_FEATURE_MASK(ID_AA64PFR0_EL1_EL2), ID_AA64PFR0_EL1_ELx_64BIT_ONLY) | \
+	FIELD_PREP(ARM64_FEATURE_MASK(ID_AA64PFR0_EL1_EL3), ID_AA64PFR0_EL1_ELx_64BIT_ONLY) | \
+	FIELD_PREP(ARM64_FEATURE_MASK(ID_AA64PFR0_EL1_RAS), ID_AA64PFR0_EL1_RAS_IMP) \
 	)
 
 /*
@@ -62,8 +62,8 @@
  * - Speculative Store Bypassing
  */
 #define PVM_ID_AA64PFR1_ALLOW (\
-	ARM64_FEATURE_MASK(ID_AA64PFR1_BT) | \
-	ARM64_FEATURE_MASK(ID_AA64PFR1_SSBS) \
+	ARM64_FEATURE_MASK(ID_AA64PFR1_EL1_BT) | \
+	ARM64_FEATURE_MASK(ID_AA64PFR1_EL1_SSBS) \
 	)
 
 /*
@@ -74,10 +74,10 @@
  * - Non-context synchronizing exception entry and exit
  */
 #define PVM_ID_AA64MMFR0_ALLOW (\
-	ARM64_FEATURE_MASK(ID_AA64MMFR0_BIGENDEL) | \
-	ARM64_FEATURE_MASK(ID_AA64MMFR0_SNSMEM) | \
-	ARM64_FEATURE_MASK(ID_AA64MMFR0_BIGENDEL0) | \
-	ARM64_FEATURE_MASK(ID_AA64MMFR0_EXS) \
+	ARM64_FEATURE_MASK(ID_AA64MMFR0_EL1_BIGEND) | \
+	ARM64_FEATURE_MASK(ID_AA64MMFR0_EL1_SNSMEM) | \
+	ARM64_FEATURE_MASK(ID_AA64MMFR0_EL1_BIGENDEL0) | \
+	ARM64_FEATURE_MASK(ID_AA64MMFR0_EL1_EXS) \
 	)
 
 /*
@@ -86,8 +86,8 @@
  * - 16-bit ASID
  */
 #define PVM_ID_AA64MMFR0_RESTRICT_UNSIGNED (\
-	FIELD_PREP(ARM64_FEATURE_MASK(ID_AA64MMFR0_PARANGE), ID_AA64MMFR0_PARANGE_40) | \
-	FIELD_PREP(ARM64_FEATURE_MASK(ID_AA64MMFR0_ASID), ID_AA64MMFR0_ASID_16) \
+	FIELD_PREP(ARM64_FEATURE_MASK(ID_AA64MMFR0_EL1_PARANGE), ID_AA64MMFR0_EL1_PARANGE_40) | \
+	FIELD_PREP(ARM64_FEATURE_MASK(ID_AA64MMFR0_EL1_ASIDBITS), ID_AA64MMFR0_EL1_ASIDBITS_16) \
 	)
 
 /*
@@ -100,12 +100,12 @@
  * - Enhanced Translation Synchronization
  */
 #define PVM_ID_AA64MMFR1_ALLOW (\
-	ARM64_FEATURE_MASK(ID_AA64MMFR1_HADBS) | \
-	ARM64_FEATURE_MASK(ID_AA64MMFR1_VMIDBITS) | \
-	ARM64_FEATURE_MASK(ID_AA64MMFR1_HPD) | \
-	ARM64_FEATURE_MASK(ID_AA64MMFR1_PAN) | \
-	ARM64_FEATURE_MASK(ID_AA64MMFR1_SPECSEI) | \
-	ARM64_FEATURE_MASK(ID_AA64MMFR1_ETS) \
+	ARM64_FEATURE_MASK(ID_AA64MMFR1_EL1_HAFDBS) | \
+	ARM64_FEATURE_MASK(ID_AA64MMFR1_EL1_VMIDBits) | \
+	ARM64_FEATURE_MASK(ID_AA64MMFR1_EL1_HPDS) | \
+	ARM64_FEATURE_MASK(ID_AA64MMFR1_EL1_PAN) | \
+	ARM64_FEATURE_MASK(ID_AA64MMFR1_EL1_SpecSEI) | \
+	ARM64_FEATURE_MASK(ID_AA64MMFR1_EL1_ETS) \
 	)
 
 /*
@@ -120,14 +120,14 @@
  * - E0PDx mechanism
  */
 #define PVM_ID_AA64MMFR2_ALLOW (\
-	ARM64_FEATURE_MASK(ID_AA64MMFR2_CNP) | \
-	ARM64_FEATURE_MASK(ID_AA64MMFR2_UAO) | \
-	ARM64_FEATURE_MASK(ID_AA64MMFR2_IESB) | \
-	ARM64_FEATURE_MASK(ID_AA64MMFR2_AT) | \
-	ARM64_FEATURE_MASK(ID_AA64MMFR2_IDS) | \
-	ARM64_FEATURE_MASK(ID_AA64MMFR2_TTL) | \
-	ARM64_FEATURE_MASK(ID_AA64MMFR2_BBM) | \
-	ARM64_FEATURE_MASK(ID_AA64MMFR2_E0PD) \
+	ARM64_FEATURE_MASK(ID_AA64MMFR2_EL1_CnP) | \
+	ARM64_FEATURE_MASK(ID_AA64MMFR2_EL1_UAO) | \
+	ARM64_FEATURE_MASK(ID_AA64MMFR2_EL1_IESB) | \
+	ARM64_FEATURE_MASK(ID_AA64MMFR2_EL1_AT) | \
+	ARM64_FEATURE_MASK(ID_AA64MMFR2_EL1_IDS) | \
+	ARM64_FEATURE_MASK(ID_AA64MMFR2_EL1_TTL) | \
+	ARM64_FEATURE_MASK(ID_AA64MMFR2_EL1_BBM) | \
+	ARM64_FEATURE_MASK(ID_AA64MMFR2_EL1_E0PD) \
 	)
 
 /*
@@ -159,37 +159,42 @@
  * No restrictions on instructions implemented in AArch64.
  */
 #define PVM_ID_AA64ISAR0_ALLOW (\
-	ARM64_FEATURE_MASK(ID_AA64ISAR0_AES) | \
-	ARM64_FEATURE_MASK(ID_AA64ISAR0_SHA1) | \
-	ARM64_FEATURE_MASK(ID_AA64ISAR0_SHA2) | \
-	ARM64_FEATURE_MASK(ID_AA64ISAR0_CRC32) | \
-	ARM64_FEATURE_MASK(ID_AA64ISAR0_ATOMICS) | \
-	ARM64_FEATURE_MASK(ID_AA64ISAR0_RDM) | \
-	ARM64_FEATURE_MASK(ID_AA64ISAR0_SHA3) | \
-	ARM64_FEATURE_MASK(ID_AA64ISAR0_SM3) | \
-	ARM64_FEATURE_MASK(ID_AA64ISAR0_SM4) | \
-	ARM64_FEATURE_MASK(ID_AA64ISAR0_DP) | \
-	ARM64_FEATURE_MASK(ID_AA64ISAR0_FHM) | \
-	ARM64_FEATURE_MASK(ID_AA64ISAR0_TS) | \
-	ARM64_FEATURE_MASK(ID_AA64ISAR0_TLB) | \
-	ARM64_FEATURE_MASK(ID_AA64ISAR0_RNDR) \
+	ARM64_FEATURE_MASK(ID_AA64ISAR0_EL1_AES) | \
+	ARM64_FEATURE_MASK(ID_AA64ISAR0_EL1_SHA1) | \
+	ARM64_FEATURE_MASK(ID_AA64ISAR0_EL1_SHA2) | \
+	ARM64_FEATURE_MASK(ID_AA64ISAR0_EL1_CRC32) | \
+	ARM64_FEATURE_MASK(ID_AA64ISAR0_EL1_ATOMIC) | \
+	ARM64_FEATURE_MASK(ID_AA64ISAR0_EL1_RDM) | \
+	ARM64_FEATURE_MASK(ID_AA64ISAR0_EL1_SHA3) | \
+	ARM64_FEATURE_MASK(ID_AA64ISAR0_EL1_SM3) | \
+	ARM64_FEATURE_MASK(ID_AA64ISAR0_EL1_SM4) | \
+	ARM64_FEATURE_MASK(ID_AA64ISAR0_EL1_DP) | \
+	ARM64_FEATURE_MASK(ID_AA64ISAR0_EL1_FHM) | \
+	ARM64_FEATURE_MASK(ID_AA64ISAR0_EL1_TS) | \
+	ARM64_FEATURE_MASK(ID_AA64ISAR0_EL1_TLB) | \
+	ARM64_FEATURE_MASK(ID_AA64ISAR0_EL1_RNDR) \
 	)
 
 #define PVM_ID_AA64ISAR1_ALLOW (\
-	ARM64_FEATURE_MASK(ID_AA64ISAR1_DPB) | \
-	ARM64_FEATURE_MASK(ID_AA64ISAR1_APA) | \
-	ARM64_FEATURE_MASK(ID_AA64ISAR1_API) | \
-	ARM64_FEATURE_MASK(ID_AA64ISAR1_JSCVT) | \
-	ARM64_FEATURE_MASK(ID_AA64ISAR1_FCMA) | \
-	ARM64_FEATURE_MASK(ID_AA64ISAR1_LRCPC) | \
-	ARM64_FEATURE_MASK(ID_AA64ISAR1_GPA) | \
-	ARM64_FEATURE_MASK(ID_AA64ISAR1_GPI) | \
-	ARM64_FEATURE_MASK(ID_AA64ISAR1_FRINTTS) | \
-	ARM64_FEATURE_MASK(ID_AA64ISAR1_SB) | \
-	ARM64_FEATURE_MASK(ID_AA64ISAR1_SPECRES) | \
-	ARM64_FEATURE_MASK(ID_AA64ISAR1_BF16) | \
-	ARM64_FEATURE_MASK(ID_AA64ISAR1_DGH) | \
-	ARM64_FEATURE_MASK(ID_AA64ISAR1_I8MM) \
+	ARM64_FEATURE_MASK(ID_AA64ISAR1_EL1_DPB) | \
+	ARM64_FEATURE_MASK(ID_AA64ISAR1_EL1_APA) | \
+	ARM64_FEATURE_MASK(ID_AA64ISAR1_EL1_API) | \
+	ARM64_FEATURE_MASK(ID_AA64ISAR1_EL1_JSCVT) | \
+	ARM64_FEATURE_MASK(ID_AA64ISAR1_EL1_FCMA) | \
+	ARM64_FEATURE_MASK(ID_AA64ISAR1_EL1_LRCPC) | \
+	ARM64_FEATURE_MASK(ID_AA64ISAR1_EL1_GPA) | \
+	ARM64_FEATURE_MASK(ID_AA64ISAR1_EL1_GPI) | \
+	ARM64_FEATURE_MASK(ID_AA64ISAR1_EL1_FRINTTS) | \
+	ARM64_FEATURE_MASK(ID_AA64ISAR1_EL1_SB) | \
+	ARM64_FEATURE_MASK(ID_AA64ISAR1_EL1_SPECRES) | \
+	ARM64_FEATURE_MASK(ID_AA64ISAR1_EL1_BF16) | \
+	ARM64_FEATURE_MASK(ID_AA64ISAR1_EL1_DGH) | \
+	ARM64_FEATURE_MASK(ID_AA64ISAR1_EL1_I8MM) \
+	)
+
+#define PVM_ID_AA64ISAR2_ALLOW (\
+	ARM64_FEATURE_MASK(ID_AA64ISAR2_EL1_GPA3) | \
+	ARM64_FEATURE_MASK(ID_AA64ISAR2_EL1_APA3) \
 	)
 
 u64 pvm_read_id_reg(const struct kvm_vcpu *vcpu, u32 id);
diff --git a/arch/arm64/kvm/hyp/include/nvhe/mem_protect.h b/arch/arm64/kvm/hyp/include/nvhe/mem_protect.h
index b58c910babaf..80e99836eac7 100644
--- a/arch/arm64/kvm/hyp/include/nvhe/mem_protect.h
+++ b/arch/arm64/kvm/hyp/include/nvhe/mem_protect.h
@@ -24,6 +24,11 @@ enum pkvm_page_state {
 	PKVM_PAGE_OWNED			= 0ULL,
 	PKVM_PAGE_SHARED_OWNED		= KVM_PGTABLE_PROT_SW0,
 	PKVM_PAGE_SHARED_BORROWED	= KVM_PGTABLE_PROT_SW1,
+	__PKVM_PAGE_RESERVED		= KVM_PGTABLE_PROT_SW0 |
+					  KVM_PGTABLE_PROT_SW1,
+
+	/* Meta-states which aren't encoded directly in the PTE's SW bits */
+	PKVM_NOPAGE,
 };
 
 #define PKVM_PAGE_STATE_PROT_MASK	(KVM_PGTABLE_PROT_SW0 | KVM_PGTABLE_PROT_SW1)
@@ -50,6 +55,7 @@ extern const u8 pkvm_hyp_id;
 
 int __pkvm_prot_finalize(void);
 int __pkvm_host_share_hyp(u64 pfn);
+int __pkvm_host_unshare_hyp(u64 pfn);
 
 bool addr_is_memory(phys_addr_t phys);
 int host_stage2_idmap_locked(phys_addr_t addr, u64 size, enum kvm_pgtable_prot prot);
diff --git a/arch/arm64/kvm/hyp/include/nvhe/mm.h b/arch/arm64/kvm/hyp/include/nvhe/mm.h
index c9a8f535212e..42d8eb9bfe72 100644
--- a/arch/arm64/kvm/hyp/include/nvhe/mm.h
+++ b/arch/arm64/kvm/hyp/include/nvhe/mm.h
@@ -10,13 +10,8 @@
 #include <nvhe/memory.h>
 #include <nvhe/spinlock.h>
 
-#define HYP_MEMBLOCK_REGIONS 128
-extern struct memblock_region kvm_nvhe_sym(hyp_memory)[];
-extern unsigned int kvm_nvhe_sym(hyp_memblock_nr);
 extern struct kvm_pgtable pkvm_pgtable;
 extern hyp_spinlock_t pkvm_pgd_lock;
-extern struct hyp_pool hpool;
-extern u64 __io_map_base;
 
 int hyp_create_idmap(u32 hyp_va_bits);
 int hyp_map_vectors(void);
@@ -24,8 +19,10 @@ int hyp_back_vmemmap(phys_addr_t phys, unsigned long size, phys_addr_t back);
 int pkvm_cpu_set_vector(enum arm64_hyp_spectre_vector slot);
 int pkvm_create_mappings(void *from, void *to, enum kvm_pgtable_prot prot);
 int pkvm_create_mappings_locked(void *from, void *to, enum kvm_pgtable_prot prot);
-unsigned long __pkvm_create_private_mapping(phys_addr_t phys, size_t size,
-					    enum kvm_pgtable_prot prot);
+int __pkvm_create_private_mapping(phys_addr_t phys, size_t size,
+				  enum kvm_pgtable_prot prot,
+				  unsigned long *haddr);
+int pkvm_alloc_private_va_range(size_t size, unsigned long *haddr);
 
 static inline void hyp_vmemmap_range(phys_addr_t phys, unsigned long size,
 				     unsigned long *start, unsigned long *end)
@@ -39,58 +36,4 @@ static inline void hyp_vmemmap_range(phys_addr_t phys, unsigned long size,
 	*end = ALIGN(*end, PAGE_SIZE);
 }
 
-static inline unsigned long __hyp_pgtable_max_pages(unsigned long nr_pages)
-{
-	unsigned long total = 0, i;
-
-	/* Provision the worst case scenario */
-	for (i = 0; i < KVM_PGTABLE_MAX_LEVELS; i++) {
-		nr_pages = DIV_ROUND_UP(nr_pages, PTRS_PER_PTE);
-		total += nr_pages;
-	}
-
-	return total;
-}
-
-static inline unsigned long __hyp_pgtable_total_pages(void)
-{
-	unsigned long res = 0, i;
-
-	/* Cover all of memory with page-granularity */
-	for (i = 0; i < kvm_nvhe_sym(hyp_memblock_nr); i++) {
-		struct memblock_region *reg = &kvm_nvhe_sym(hyp_memory)[i];
-		res += __hyp_pgtable_max_pages(reg->size >> PAGE_SHIFT);
-	}
-
-	return res;
-}
-
-static inline unsigned long hyp_s1_pgtable_pages(void)
-{
-	unsigned long res;
-
-	res = __hyp_pgtable_total_pages();
-
-	/* Allow 1 GiB for private mappings */
-	res += __hyp_pgtable_max_pages(SZ_1G >> PAGE_SHIFT);
-
-	return res;
-}
-
-static inline unsigned long host_s2_pgtable_pages(void)
-{
-	unsigned long res;
-
-	/*
-	 * Include an extra 16 pages to safely upper-bound the worst case of
-	 * concatenated pgds.
-	 */
-	res = __hyp_pgtable_total_pages() + 16;
-
-	/* Allow 1 GiB for MMIO mappings */
-	res += __hyp_pgtable_max_pages(SZ_1G >> PAGE_SHIFT);
-
-	return res;
-}
-
 #endif /* __KVM_HYP_MM_H */
diff --git a/arch/arm64/kvm/hyp/nvhe/Makefile b/arch/arm64/kvm/hyp/nvhe/Makefile
index c3c11974fa3b..be0a2bc3e20d 100644
--- a/arch/arm64/kvm/hyp/nvhe/Makefile
+++ b/arch/arm64/kvm/hyp/nvhe/Makefile
@@ -4,7 +4,15 @@
 #
 
 asflags-y := -D__KVM_NVHE_HYPERVISOR__ -D__DISABLE_EXPORTS
-ccflags-y := -D__KVM_NVHE_HYPERVISOR__ -D__DISABLE_EXPORTS
+
+# Tracepoint and MMIO logging symbols should not be visible at nVHE KVM as
+# there is no way to execute them and any such MMIO access from nVHE KVM
+# will explode instantly (Words of Marc Zyngier). So introduce a generic flag
+# __DISABLE_TRACE_MMIO__ to disable MMIO tracing for nVHE KVM.
+ccflags-y := -D__KVM_NVHE_HYPERVISOR__ -D__DISABLE_EXPORTS -D__DISABLE_TRACE_MMIO__
+ccflags-y += -fno-stack-protector	\
+	     -DDISABLE_BRANCH_PROFILING	\
+	     $(DISABLE_STACKLEAK_PLUGIN)
 
 hostprogs := gen-hyprel
 HOST_EXTRACFLAGS += -I$(objtree)/include
@@ -12,12 +20,13 @@ HOST_EXTRACFLAGS += -I$(objtree)/include
 lib-objs := clear_page.o copy_page.o memcpy.o memset.o
 lib-objs := $(addprefix ../../../lib/, $(lib-objs))
 
-obj-y := timer-sr.o sysreg-sr.o debug-sr.o switch.o tlb.o hyp-init.o host.o \
-	 hyp-main.o hyp-smp.o psci-relay.o early_alloc.o stub.o page_alloc.o \
-	 cache.o setup.o mm.o mem_protect.o sys_regs.o pkvm.o
-obj-y += ../vgic-v3-sr.o ../aarch32.o ../vgic-v2-cpuif-proxy.o ../entry.o \
+hyp-obj-y := timer-sr.o sysreg-sr.o debug-sr.o switch.o tlb.o hyp-init.o host.o \
+	 hyp-main.o hyp-smp.o psci-relay.o early_alloc.o page_alloc.o \
+	 cache.o setup.o mm.o mem_protect.o sys_regs.o pkvm.o stacktrace.o
+hyp-obj-y += ../vgic-v3-sr.o ../aarch32.o ../vgic-v2-cpuif-proxy.o ../entry.o \
 	 ../fpsimd.o ../hyp-entry.o ../exception.o ../pgtable.o
-obj-y += $(lib-objs)
+hyp-obj-$(CONFIG_DEBUG_LIST) += list_debug.o
+hyp-obj-y += $(lib-objs)
 
 ##
 ## Build rules for compiling nVHE hyp code
@@ -25,9 +34,9 @@ obj-y += $(lib-objs)
 ## file containing all nVHE hyp code and data.
 ##
 
-hyp-obj := $(patsubst %.o,%.nvhe.o,$(obj-y))
+hyp-obj := $(patsubst %.o,%.nvhe.o,$(hyp-obj-y))
 obj-y := kvm_nvhe.o
-extra-y := $(hyp-obj) kvm_nvhe.tmp.o kvm_nvhe.rel.o hyp.lds hyp-reloc.S hyp-reloc.o
+targets += $(hyp-obj) kvm_nvhe.tmp.o kvm_nvhe.rel.o hyp.lds hyp-reloc.S hyp-reloc.o
 
 # 1) Compile all source files to `.nvhe.o` object files. The file extension
 #    avoids file name clashes for files shared with VHE.
@@ -83,12 +92,17 @@ quiet_cmd_hypcopy = HYPCOPY $@
 # Remove ftrace, Shadow Call Stack, and CFI CFLAGS.
 # This is equivalent to the 'notrace', '__noscs', and '__nocfi' annotations.
 KBUILD_CFLAGS := $(filter-out $(CC_FLAGS_FTRACE) $(CC_FLAGS_SCS) $(CC_FLAGS_CFI), $(KBUILD_CFLAGS))
+# Starting from 13.0.0 llvm emits SHT_REL section '.llvm.call-graph-profile'
+# when profile optimization is applied. gen-hyprel does not support SHT_REL and
+# causes a build failure. Remove profile optimization flags.
+KBUILD_CFLAGS := $(filter-out -fprofile-sample-use=% -fprofile-use=%, $(KBUILD_CFLAGS))
 
 # KVM nVHE code is run at a different exception code with a different map, so
 # compiler instrumentation that inserts callbacks or checks into the code may
 # cause crashes. Just disable it.
 GCOV_PROFILE	:= n
 KASAN_SANITIZE	:= n
+KCSAN_SANITIZE	:= n
 UBSAN_SANITIZE	:= n
 KCOV_INSTRUMENT	:= n
 
diff --git a/arch/arm64/kvm/hyp/nvhe/cache.S b/arch/arm64/kvm/hyp/nvhe/cache.S
index 958734f4d6b0..0c367eb5f4e2 100644
--- a/arch/arm64/kvm/hyp/nvhe/cache.S
+++ b/arch/arm64/kvm/hyp/nvhe/cache.S
@@ -7,7 +7,8 @@
 #include <asm/assembler.h>
 #include <asm/alternative.h>
 
-SYM_FUNC_START_PI(dcache_clean_inval_poc)
+SYM_FUNC_START(__pi_dcache_clean_inval_poc)
 	dcache_by_line_op civac, sy, x0, x1, x2, x3
 	ret
-SYM_FUNC_END_PI(dcache_clean_inval_poc)
+SYM_FUNC_END(__pi_dcache_clean_inval_poc)
+SYM_FUNC_ALIAS(dcache_clean_inval_poc, __pi_dcache_clean_inval_poc)
diff --git a/arch/arm64/kvm/hyp/nvhe/debug-sr.c b/arch/arm64/kvm/hyp/nvhe/debug-sr.c
index df361d839902..e17455773b98 100644
--- a/arch/arm64/kvm/hyp/nvhe/debug-sr.c
+++ b/arch/arm64/kvm/hyp/nvhe/debug-sr.c
@@ -84,10 +84,10 @@ static void __debug_restore_trace(u64 trfcr_el1)
 void __debug_save_host_buffers_nvhe(struct kvm_vcpu *vcpu)
 {
 	/* Disable and flush SPE data generation */
-	if (vcpu->arch.flags & KVM_ARM64_DEBUG_STATE_SAVE_SPE)
+	if (vcpu_get_flag(vcpu, DEBUG_STATE_SAVE_SPE))
 		__debug_save_spe(&vcpu->arch.host_debug_state.pmscr_el1);
 	/* Disable and flush Self-Hosted Trace generation */
-	if (vcpu->arch.flags & KVM_ARM64_DEBUG_STATE_SAVE_TRBE)
+	if (vcpu_get_flag(vcpu, DEBUG_STATE_SAVE_TRBE))
 		__debug_save_trace(&vcpu->arch.host_debug_state.trfcr_el1);
 }
 
@@ -98,9 +98,9 @@ void __debug_switch_to_guest(struct kvm_vcpu *vcpu)
 
 void __debug_restore_host_buffers_nvhe(struct kvm_vcpu *vcpu)
 {
-	if (vcpu->arch.flags & KVM_ARM64_DEBUG_STATE_SAVE_SPE)
+	if (vcpu_get_flag(vcpu, DEBUG_STATE_SAVE_SPE))
 		__debug_restore_spe(vcpu->arch.host_debug_state.pmscr_el1);
-	if (vcpu->arch.flags & KVM_ARM64_DEBUG_STATE_SAVE_TRBE)
+	if (vcpu_get_flag(vcpu, DEBUG_STATE_SAVE_TRBE))
 		__debug_restore_trace(vcpu->arch.host_debug_state.trfcr_el1);
 }
 
diff --git a/arch/arm64/kvm/hyp/nvhe/early_alloc.c b/arch/arm64/kvm/hyp/nvhe/early_alloc.c
index 1306c430ab87..00de04153cc6 100644
--- a/arch/arm64/kvm/hyp/nvhe/early_alloc.c
+++ b/arch/arm64/kvm/hyp/nvhe/early_alloc.c
@@ -43,6 +43,9 @@ void *hyp_early_alloc_page(void *arg)
 	return hyp_early_alloc_contig(1);
 }
 
+static void hyp_early_alloc_get_page(void *addr) { }
+static void hyp_early_alloc_put_page(void *addr) { }
+
 void hyp_early_alloc_init(void *virt, unsigned long size)
 {
 	base = cur = (unsigned long)virt;
@@ -51,4 +54,6 @@ void hyp_early_alloc_init(void *virt, unsigned long size)
 	hyp_early_alloc_mm_ops.zalloc_page = hyp_early_alloc_page;
 	hyp_early_alloc_mm_ops.phys_to_virt = hyp_phys_to_virt;
 	hyp_early_alloc_mm_ops.virt_to_phys = hyp_virt_to_phys;
+	hyp_early_alloc_mm_ops.get_page = hyp_early_alloc_get_page;
+	hyp_early_alloc_mm_ops.put_page = hyp_early_alloc_put_page;
 }
diff --git a/arch/arm64/kvm/hyp/nvhe/host.S b/arch/arm64/kvm/hyp/nvhe/host.S
index 3d613e721a75..b6c0188c4b35 100644
--- a/arch/arm64/kvm/hyp/nvhe/host.S
+++ b/arch/arm64/kvm/hyp/nvhe/host.S
@@ -80,7 +80,7 @@ SYM_FUNC_START(__hyp_do_panic)
 	mov	lr, #(PSR_F_BIT | PSR_I_BIT | PSR_A_BIT | PSR_D_BIT |\
 		      PSR_MODE_EL1h)
 	msr	spsr_el2, lr
-	ldr	lr, =nvhe_hyp_panic_handler
+	adr_l	lr, nvhe_hyp_panic_handler
 	hyp_kimg_va lr, x6
 	msr	elr_el2, lr
 
@@ -125,13 +125,11 @@ alternative_else_nop_endif
 	add	sp, sp, #16
 	/*
 	 * Compute the idmap address of __kvm_handle_stub_hvc and
-	 * jump there. Since we use kimage_voffset, do not use the
-	 * HYP VA for __kvm_handle_stub_hvc, but the kernel VA instead
-	 * (by loading it from the constant pool).
+	 * jump there.
 	 *
 	 * Preserve x0-x4, which may contain stub parameters.
 	 */
-	ldr	x5, =__kvm_handle_stub_hvc
+	adr_l	x5, __kvm_handle_stub_hvc
 	hyp_pa	x5, x6
 	br	x5
 SYM_FUNC_END(__host_hvc)
@@ -153,6 +151,18 @@ SYM_FUNC_END(__host_hvc)
 
 .macro invalid_host_el2_vect
 	.align 7
+
+	/*
+	 * Test whether the SP has overflowed, without corrupting a GPR.
+	 * nVHE hypervisor stacks are aligned so that the PAGE_SHIFT bit
+	 * of SP should always be 1.
+	 */
+	add	sp, sp, x0			// sp' = sp + x0
+	sub	x0, sp, x0			// x0' = sp' - x0 = (sp + x0) - x0 = sp
+	tbz	x0, #PAGE_SHIFT, .L__hyp_sp_overflow\@
+	sub	x0, sp, x0			// x0'' = sp' - x0' = (sp + x0) - sp = x0
+	sub	sp, sp, x0			// sp'' = sp' - x0 = (sp + x0) - x0 = sp
+
 	/* If a guest is loaded, panic out of it. */
 	stp	x0, x1, [sp, #-16]!
 	get_loaded_vcpu x0, x1
@@ -165,6 +175,13 @@ SYM_FUNC_END(__host_hvc)
 	 * been partially clobbered by __host_enter.
 	 */
 	b	hyp_panic
+
+.L__hyp_sp_overflow\@:
+	/* Switch to the overflow stack */
+	adr_this_cpu sp, overflow_stack + OVERFLOW_STACK_SIZE, x0
+
+	b	hyp_panic_bad_stack
+	ASM_BUG()
 .endm
 
 .macro invalid_host_el1_vect
@@ -198,15 +215,15 @@ SYM_CODE_START(__kvm_hyp_host_vector)
 	invalid_host_el2_vect			// FIQ EL2h
 	invalid_host_el2_vect			// Error EL2h
 
-	host_el1_sync_vect			// Synchronous 64-bit EL1
-	invalid_host_el1_vect			// IRQ 64-bit EL1
-	invalid_host_el1_vect			// FIQ 64-bit EL1
-	invalid_host_el1_vect			// Error 64-bit EL1
+	host_el1_sync_vect			// Synchronous 64-bit EL1/EL0
+	invalid_host_el1_vect			// IRQ 64-bit EL1/EL0
+	invalid_host_el1_vect			// FIQ 64-bit EL1/EL0
+	invalid_host_el1_vect			// Error 64-bit EL1/EL0
 
-	invalid_host_el1_vect			// Synchronous 32-bit EL1
-	invalid_host_el1_vect			// IRQ 32-bit EL1
-	invalid_host_el1_vect			// FIQ 32-bit EL1
-	invalid_host_el1_vect			// Error 32-bit EL1
+	host_el1_sync_vect			// Synchronous 32-bit EL1/EL0
+	invalid_host_el1_vect			// IRQ 32-bit EL1/EL0
+	invalid_host_el1_vect			// FIQ 32-bit EL1/EL0
+	invalid_host_el1_vect			// Error 32-bit EL1/EL0
 SYM_CODE_END(__kvm_hyp_host_vector)
 
 /*
diff --git a/arch/arm64/kvm/hyp/nvhe/hyp-main.c b/arch/arm64/kvm/hyp/nvhe/hyp-main.c
index b096bf009144..3cea4b6ac23e 100644
--- a/arch/arm64/kvm/hyp/nvhe/hyp-main.c
+++ b/arch/arm64/kvm/hyp/nvhe/hyp-main.c
@@ -147,13 +147,36 @@ static void handle___pkvm_host_share_hyp(struct kvm_cpu_context *host_ctxt)
 	cpu_reg(host_ctxt, 1) = __pkvm_host_share_hyp(pfn);
 }
 
+static void handle___pkvm_host_unshare_hyp(struct kvm_cpu_context *host_ctxt)
+{
+	DECLARE_REG(u64, pfn, host_ctxt, 1);
+
+	cpu_reg(host_ctxt, 1) = __pkvm_host_unshare_hyp(pfn);
+}
+
 static void handle___pkvm_create_private_mapping(struct kvm_cpu_context *host_ctxt)
 {
 	DECLARE_REG(phys_addr_t, phys, host_ctxt, 1);
 	DECLARE_REG(size_t, size, host_ctxt, 2);
 	DECLARE_REG(enum kvm_pgtable_prot, prot, host_ctxt, 3);
 
-	cpu_reg(host_ctxt, 1) = __pkvm_create_private_mapping(phys, size, prot);
+	/*
+	 * __pkvm_create_private_mapping() populates a pointer with the
+	 * hypervisor start address of the allocation.
+	 *
+	 * However, handle___pkvm_create_private_mapping() hypercall crosses the
+	 * EL1/EL2 boundary so the pointer would not be valid in this context.
+	 *
+	 * Instead pass the allocation address as the return value (or return
+	 * ERR_PTR() on failure).
+	 */
+	unsigned long haddr;
+	int err = __pkvm_create_private_mapping(phys, size, prot, &haddr);
+
+	if (err)
+		haddr = (unsigned long)ERR_PTR(err);
+
+	cpu_reg(host_ctxt, 1) = haddr;
 }
 
 static void handle___pkvm_prot_finalize(struct kvm_cpu_context *host_ctxt)
@@ -184,6 +207,7 @@ static const hcall_t host_hcall[] = {
 	HANDLE_FUNC(__pkvm_prot_finalize),
 
 	HANDLE_FUNC(__pkvm_host_share_hyp),
+	HANDLE_FUNC(__pkvm_host_unshare_hyp),
 	HANDLE_FUNC(__kvm_adjust_pc),
 	HANDLE_FUNC(__kvm_vcpu_run),
 	HANDLE_FUNC(__kvm_flush_vm_context),
diff --git a/arch/arm64/kvm/hyp/nvhe/list_debug.c b/arch/arm64/kvm/hyp/nvhe/list_debug.c
new file mode 100644
index 000000000000..d68abd7ea124
--- /dev/null
+++ b/arch/arm64/kvm/hyp/nvhe/list_debug.c
@@ -0,0 +1,54 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2022 - Google LLC
+ * Author: Keir Fraser <keirf@google.com>
+ */
+
+#include <linux/list.h>
+#include <linux/bug.h>
+
+static inline __must_check bool nvhe_check_data_corruption(bool v)
+{
+	return v;
+}
+
+#define NVHE_CHECK_DATA_CORRUPTION(condition)				 \
+	nvhe_check_data_corruption(({					 \
+		bool corruption = unlikely(condition);			 \
+		if (corruption) {					 \
+			if (IS_ENABLED(CONFIG_BUG_ON_DATA_CORRUPTION)) { \
+				BUG_ON(1);				 \
+			} else						 \
+				WARN_ON(1);				 \
+		}							 \
+		corruption;						 \
+	}))
+
+/* The predicates checked here are taken from lib/list_debug.c. */
+
+bool __list_add_valid(struct list_head *new, struct list_head *prev,
+		      struct list_head *next)
+{
+	if (NVHE_CHECK_DATA_CORRUPTION(next->prev != prev) ||
+	    NVHE_CHECK_DATA_CORRUPTION(prev->next != next) ||
+	    NVHE_CHECK_DATA_CORRUPTION(new == prev || new == next))
+		return false;
+
+	return true;
+}
+
+bool __list_del_entry_valid(struct list_head *entry)
+{
+	struct list_head *prev, *next;
+
+	prev = entry->prev;
+	next = entry->next;
+
+	if (NVHE_CHECK_DATA_CORRUPTION(next == LIST_POISON1) ||
+	    NVHE_CHECK_DATA_CORRUPTION(prev == LIST_POISON2) ||
+	    NVHE_CHECK_DATA_CORRUPTION(prev->next != entry) ||
+	    NVHE_CHECK_DATA_CORRUPTION(next->prev != entry))
+		return false;
+
+	return true;
+}
diff --git a/arch/arm64/kvm/hyp/nvhe/mem_protect.c b/arch/arm64/kvm/hyp/nvhe/mem_protect.c
index c1a90dd022b8..07f9dc9848ef 100644
--- a/arch/arm64/kvm/hyp/nvhe/mem_protect.c
+++ b/arch/arm64/kvm/hyp/nvhe/mem_protect.c
@@ -9,6 +9,7 @@
 #include <asm/kvm_hyp.h>
 #include <asm/kvm_mmu.h>
 #include <asm/kvm_pgtable.h>
+#include <asm/kvm_pkvm.h>
 #include <asm/stage2_pgtable.h>
 
 #include <hyp/fault.h>
@@ -27,6 +28,26 @@ static struct hyp_pool host_s2_pool;
 
 const u8 pkvm_hyp_id = 1;
 
+static void host_lock_component(void)
+{
+	hyp_spin_lock(&host_kvm.lock);
+}
+
+static void host_unlock_component(void)
+{
+	hyp_spin_unlock(&host_kvm.lock);
+}
+
+static void hyp_lock_component(void)
+{
+	hyp_spin_lock(&pkvm_pgd_lock);
+}
+
+static void hyp_unlock_component(void)
+{
+	hyp_spin_unlock(&pkvm_pgd_lock);
+}
+
 static void *host_s2_zalloc_pages_exact(size_t size)
 {
 	void *addr = hyp_alloc_pages(&host_s2_pool, get_order(size));
@@ -103,22 +124,21 @@ int kvm_host_prepare_stage2(void *pgt_pool_base)
 
 	prepare_host_vtcr();
 	hyp_spin_lock_init(&host_kvm.lock);
+	mmu->arch = &host_kvm.arch;
 
 	ret = prepare_s2_pool(pgt_pool_base);
 	if (ret)
 		return ret;
 
-	ret = __kvm_pgtable_stage2_init(&host_kvm.pgt, &host_kvm.arch,
+	ret = __kvm_pgtable_stage2_init(&host_kvm.pgt, mmu,
 					&host_kvm.mm_ops, KVM_HOST_S2_FLAGS,
 					host_stage2_force_pte_cb);
 	if (ret)
 		return ret;
 
 	mmu->pgd_phys = __hyp_pa(host_kvm.pgt.pgd);
-	mmu->arch = &host_kvm.arch;
 	mmu->pgt = &host_kvm.pgt;
-	WRITE_ONCE(mmu->vmid.vmid_gen, 0);
-	WRITE_ONCE(mmu->vmid.vmid, 0);
+	atomic64_set(&mmu->vmid.id, 0);
 
 	return 0;
 }
@@ -294,15 +314,11 @@ static int host_stage2_adjust_range(u64 addr, struct kvm_mem_range *range)
 int host_stage2_idmap_locked(phys_addr_t addr, u64 size,
 			     enum kvm_pgtable_prot prot)
 {
-	hyp_assert_lock_held(&host_kvm.lock);
-
 	return host_stage2_try(__host_stage2_idmap, addr, addr + size, prot);
 }
 
 int host_stage2_set_owner_locked(phys_addr_t addr, u64 size, u8 owner_id)
 {
-	hyp_assert_lock_held(&host_kvm.lock);
-
 	return host_stage2_try(kvm_pgtable_stage2_set_owner, &host_kvm.pgt,
 			       addr, size, &host_s2_pool, owner_id);
 }
@@ -338,116 +354,446 @@ static int host_stage2_idmap(u64 addr)
 
 	prot = is_memory ? PKVM_HOST_MEM_PROT : PKVM_HOST_MMIO_PROT;
 
-	hyp_spin_lock(&host_kvm.lock);
+	host_lock_component();
 	ret = host_stage2_adjust_range(addr, &range);
 	if (ret)
 		goto unlock;
 
 	ret = host_stage2_idmap_locked(range.start, range.end - range.start, prot);
 unlock:
-	hyp_spin_unlock(&host_kvm.lock);
+	host_unlock_component();
 
 	return ret;
 }
 
-static inline bool check_prot(enum kvm_pgtable_prot prot,
-			      enum kvm_pgtable_prot required,
-			      enum kvm_pgtable_prot denied)
+void handle_host_mem_abort(struct kvm_cpu_context *host_ctxt)
 {
-	return (prot & (required | denied)) == required;
+	struct kvm_vcpu_fault_info fault;
+	u64 esr, addr;
+	int ret = 0;
+
+	esr = read_sysreg_el2(SYS_ESR);
+	BUG_ON(!__get_fault_info(esr, &fault));
+
+	addr = (fault.hpfar_el2 & HPFAR_MASK) << 8;
+	ret = host_stage2_idmap(addr);
+	BUG_ON(ret && ret != -EAGAIN);
 }
 
-int __pkvm_host_share_hyp(u64 pfn)
+/* This corresponds to locking order */
+enum pkvm_component_id {
+	PKVM_ID_HOST,
+	PKVM_ID_HYP,
+};
+
+struct pkvm_mem_transition {
+	u64				nr_pages;
+
+	struct {
+		enum pkvm_component_id	id;
+		/* Address in the initiator's address space */
+		u64			addr;
+
+		union {
+			struct {
+				/* Address in the completer's address space */
+				u64	completer_addr;
+			} host;
+		};
+	} initiator;
+
+	struct {
+		enum pkvm_component_id	id;
+	} completer;
+};
+
+struct pkvm_mem_share {
+	const struct pkvm_mem_transition	tx;
+	const enum kvm_pgtable_prot		completer_prot;
+};
+
+struct check_walk_data {
+	enum pkvm_page_state	desired;
+	enum pkvm_page_state	(*get_page_state)(kvm_pte_t pte);
+};
+
+static int __check_page_state_visitor(u64 addr, u64 end, u32 level,
+				      kvm_pte_t *ptep,
+				      enum kvm_pgtable_walk_flags flag,
+				      void * const arg)
 {
-	phys_addr_t addr = hyp_pfn_to_phys(pfn);
-	enum kvm_pgtable_prot prot, cur;
-	void *virt = __hyp_va(addr);
-	enum pkvm_page_state state;
-	kvm_pte_t pte;
-	int ret;
+	struct check_walk_data *d = arg;
+	kvm_pte_t pte = *ptep;
 
-	if (!addr_is_memory(addr))
+	if (kvm_pte_valid(pte) && !addr_is_memory(kvm_pte_to_phys(pte)))
 		return -EINVAL;
 
-	hyp_spin_lock(&host_kvm.lock);
-	hyp_spin_lock(&pkvm_pgd_lock);
+	return d->get_page_state(pte) == d->desired ? 0 : -EPERM;
+}
+
+static int check_page_state_range(struct kvm_pgtable *pgt, u64 addr, u64 size,
+				  struct check_walk_data *data)
+{
+	struct kvm_pgtable_walker walker = {
+		.cb	= __check_page_state_visitor,
+		.arg	= data,
+		.flags	= KVM_PGTABLE_WALK_LEAF,
+	};
+
+	return kvm_pgtable_walk(pgt, addr, size, &walker);
+}
+
+static enum pkvm_page_state host_get_page_state(kvm_pte_t pte)
+{
+	if (!kvm_pte_valid(pte) && pte)
+		return PKVM_NOPAGE;
+
+	return pkvm_getstate(kvm_pgtable_stage2_pte_prot(pte));
+}
+
+static int __host_check_page_state_range(u64 addr, u64 size,
+					 enum pkvm_page_state state)
+{
+	struct check_walk_data d = {
+		.desired	= state,
+		.get_page_state	= host_get_page_state,
+	};
+
+	hyp_assert_lock_held(&host_kvm.lock);
+	return check_page_state_range(&host_kvm.pgt, addr, size, &d);
+}
+
+static int __host_set_page_state_range(u64 addr, u64 size,
+				       enum pkvm_page_state state)
+{
+	enum kvm_pgtable_prot prot = pkvm_mkstate(PKVM_HOST_MEM_PROT, state);
+
+	return host_stage2_idmap_locked(addr, size, prot);
+}
+
+static int host_request_owned_transition(u64 *completer_addr,
+					 const struct pkvm_mem_transition *tx)
+{
+	u64 size = tx->nr_pages * PAGE_SIZE;
+	u64 addr = tx->initiator.addr;
+
+	*completer_addr = tx->initiator.host.completer_addr;
+	return __host_check_page_state_range(addr, size, PKVM_PAGE_OWNED);
+}
+
+static int host_request_unshare(u64 *completer_addr,
+				const struct pkvm_mem_transition *tx)
+{
+	u64 size = tx->nr_pages * PAGE_SIZE;
+	u64 addr = tx->initiator.addr;
+
+	*completer_addr = tx->initiator.host.completer_addr;
+	return __host_check_page_state_range(addr, size, PKVM_PAGE_SHARED_OWNED);
+}
+
+static int host_initiate_share(u64 *completer_addr,
+			       const struct pkvm_mem_transition *tx)
+{
+	u64 size = tx->nr_pages * PAGE_SIZE;
+	u64 addr = tx->initiator.addr;
+
+	*completer_addr = tx->initiator.host.completer_addr;
+	return __host_set_page_state_range(addr, size, PKVM_PAGE_SHARED_OWNED);
+}
+
+static int host_initiate_unshare(u64 *completer_addr,
+				 const struct pkvm_mem_transition *tx)
+{
+	u64 size = tx->nr_pages * PAGE_SIZE;
+	u64 addr = tx->initiator.addr;
+
+	*completer_addr = tx->initiator.host.completer_addr;
+	return __host_set_page_state_range(addr, size, PKVM_PAGE_OWNED);
+}
+
+static enum pkvm_page_state hyp_get_page_state(kvm_pte_t pte)
+{
+	if (!kvm_pte_valid(pte))
+		return PKVM_NOPAGE;
+
+	return pkvm_getstate(kvm_pgtable_hyp_pte_prot(pte));
+}
+
+static int __hyp_check_page_state_range(u64 addr, u64 size,
+					enum pkvm_page_state state)
+{
+	struct check_walk_data d = {
+		.desired	= state,
+		.get_page_state	= hyp_get_page_state,
+	};
+
+	hyp_assert_lock_held(&pkvm_pgd_lock);
+	return check_page_state_range(&pkvm_pgtable, addr, size, &d);
+}
+
+static bool __hyp_ack_skip_pgtable_check(const struct pkvm_mem_transition *tx)
+{
+	return !(IS_ENABLED(CONFIG_NVHE_EL2_DEBUG) ||
+		 tx->initiator.id != PKVM_ID_HOST);
+}
+
+static int hyp_ack_share(u64 addr, const struct pkvm_mem_transition *tx,
+			 enum kvm_pgtable_prot perms)
+{
+	u64 size = tx->nr_pages * PAGE_SIZE;
+
+	if (perms != PAGE_HYP)
+		return -EPERM;
+
+	if (__hyp_ack_skip_pgtable_check(tx))
+		return 0;
+
+	return __hyp_check_page_state_range(addr, size, PKVM_NOPAGE);
+}
+
+static int hyp_ack_unshare(u64 addr, const struct pkvm_mem_transition *tx)
+{
+	u64 size = tx->nr_pages * PAGE_SIZE;
+
+	if (__hyp_ack_skip_pgtable_check(tx))
+		return 0;
+
+	return __hyp_check_page_state_range(addr, size,
+					    PKVM_PAGE_SHARED_BORROWED);
+}
+
+static int hyp_complete_share(u64 addr, const struct pkvm_mem_transition *tx,
+			      enum kvm_pgtable_prot perms)
+{
+	void *start = (void *)addr, *end = start + (tx->nr_pages * PAGE_SIZE);
+	enum kvm_pgtable_prot prot;
+
+	prot = pkvm_mkstate(perms, PKVM_PAGE_SHARED_BORROWED);
+	return pkvm_create_mappings_locked(start, end, prot);
+}
+
+static int hyp_complete_unshare(u64 addr, const struct pkvm_mem_transition *tx)
+{
+	u64 size = tx->nr_pages * PAGE_SIZE;
+	int ret = kvm_pgtable_hyp_unmap(&pkvm_pgtable, addr, size);
+
+	return (ret != size) ? -EFAULT : 0;
+}
+
+static int check_share(struct pkvm_mem_share *share)
+{
+	const struct pkvm_mem_transition *tx = &share->tx;
+	u64 completer_addr;
+	int ret;
+
+	switch (tx->initiator.id) {
+	case PKVM_ID_HOST:
+		ret = host_request_owned_transition(&completer_addr, tx);
+		break;
+	default:
+		ret = -EINVAL;
+	}
 
-	ret = kvm_pgtable_get_leaf(&host_kvm.pgt, addr, &pte, NULL);
 	if (ret)
-		goto unlock;
-	if (!pte)
-		goto map_shared;
+		return ret;
 
-	/*
-	 * Check attributes in the host stage-2 PTE. We need the page to be:
-	 *  - mapped RWX as we're sharing memory;
-	 *  - not borrowed, as that implies absence of ownership.
-	 * Otherwise, we can't let it got through
-	 */
-	cur = kvm_pgtable_stage2_pte_prot(pte);
-	prot = pkvm_mkstate(0, PKVM_PAGE_SHARED_BORROWED);
-	if (!check_prot(cur, PKVM_HOST_MEM_PROT, prot)) {
-		ret = -EPERM;
-		goto unlock;
+	switch (tx->completer.id) {
+	case PKVM_ID_HYP:
+		ret = hyp_ack_share(completer_addr, tx, share->completer_prot);
+		break;
+	default:
+		ret = -EINVAL;
 	}
 
-	state = pkvm_getstate(cur);
-	if (state == PKVM_PAGE_OWNED)
-		goto map_shared;
+	return ret;
+}
 
-	/*
-	 * Tolerate double-sharing the same page, but this requires
-	 * cross-checking the hypervisor stage-1.
-	 */
-	if (state != PKVM_PAGE_SHARED_OWNED) {
-		ret = -EPERM;
-		goto unlock;
+static int __do_share(struct pkvm_mem_share *share)
+{
+	const struct pkvm_mem_transition *tx = &share->tx;
+	u64 completer_addr;
+	int ret;
+
+	switch (tx->initiator.id) {
+	case PKVM_ID_HOST:
+		ret = host_initiate_share(&completer_addr, tx);
+		break;
+	default:
+		ret = -EINVAL;
 	}
 
-	ret = kvm_pgtable_get_leaf(&pkvm_pgtable, (u64)virt, &pte, NULL);
 	if (ret)
-		goto unlock;
+		return ret;
 
-	/*
-	 * If the page has been shared with the hypervisor, it must be
-	 * already mapped as SHARED_BORROWED in its stage-1.
-	 */
-	cur = kvm_pgtable_hyp_pte_prot(pte);
-	prot = pkvm_mkstate(PAGE_HYP, PKVM_PAGE_SHARED_BORROWED);
-	if (!check_prot(cur, prot, ~prot))
-		ret = -EPERM;
-	goto unlock;
+	switch (tx->completer.id) {
+	case PKVM_ID_HYP:
+		ret = hyp_complete_share(completer_addr, tx, share->completer_prot);
+		break;
+	default:
+		ret = -EINVAL;
+	}
 
-map_shared:
-	/*
-	 * If the page is not yet shared, adjust mappings in both page-tables
-	 * while both locks are held.
-	 */
-	prot = pkvm_mkstate(PAGE_HYP, PKVM_PAGE_SHARED_BORROWED);
-	ret = pkvm_create_mappings_locked(virt, virt + PAGE_SIZE, prot);
-	BUG_ON(ret);
+	return ret;
+}
+
+/*
+ * do_share():
+ *
+ * The page owner grants access to another component with a given set
+ * of permissions.
+ *
+ * Initiator: OWNED	=> SHARED_OWNED
+ * Completer: NOPAGE	=> SHARED_BORROWED
+ */
+static int do_share(struct pkvm_mem_share *share)
+{
+	int ret;
 
-	prot = pkvm_mkstate(PKVM_HOST_MEM_PROT, PKVM_PAGE_SHARED_OWNED);
-	ret = host_stage2_idmap_locked(addr, PAGE_SIZE, prot);
-	BUG_ON(ret);
+	ret = check_share(share);
+	if (ret)
+		return ret;
 
-unlock:
-	hyp_spin_unlock(&pkvm_pgd_lock);
-	hyp_spin_unlock(&host_kvm.lock);
+	return WARN_ON(__do_share(share));
+}
+
+static int check_unshare(struct pkvm_mem_share *share)
+{
+	const struct pkvm_mem_transition *tx = &share->tx;
+	u64 completer_addr;
+	int ret;
+
+	switch (tx->initiator.id) {
+	case PKVM_ID_HOST:
+		ret = host_request_unshare(&completer_addr, tx);
+		break;
+	default:
+		ret = -EINVAL;
+	}
+
+	if (ret)
+		return ret;
+
+	switch (tx->completer.id) {
+	case PKVM_ID_HYP:
+		ret = hyp_ack_unshare(completer_addr, tx);
+		break;
+	default:
+		ret = -EINVAL;
+	}
 
 	return ret;
 }
 
-void handle_host_mem_abort(struct kvm_cpu_context *host_ctxt)
+static int __do_unshare(struct pkvm_mem_share *share)
 {
-	struct kvm_vcpu_fault_info fault;
-	u64 esr, addr;
-	int ret = 0;
+	const struct pkvm_mem_transition *tx = &share->tx;
+	u64 completer_addr;
+	int ret;
 
-	esr = read_sysreg_el2(SYS_ESR);
-	BUG_ON(!__get_fault_info(esr, &fault));
+	switch (tx->initiator.id) {
+	case PKVM_ID_HOST:
+		ret = host_initiate_unshare(&completer_addr, tx);
+		break;
+	default:
+		ret = -EINVAL;
+	}
 
-	addr = (fault.hpfar_el2 & HPFAR_MASK) << 8;
-	ret = host_stage2_idmap(addr);
-	BUG_ON(ret && ret != -EAGAIN);
+	if (ret)
+		return ret;
+
+	switch (tx->completer.id) {
+	case PKVM_ID_HYP:
+		ret = hyp_complete_unshare(completer_addr, tx);
+		break;
+	default:
+		ret = -EINVAL;
+	}
+
+	return ret;
+}
+
+/*
+ * do_unshare():
+ *
+ * The page owner revokes access from another component for a range of
+ * pages which were previously shared using do_share().
+ *
+ * Initiator: SHARED_OWNED	=> OWNED
+ * Completer: SHARED_BORROWED	=> NOPAGE
+ */
+static int do_unshare(struct pkvm_mem_share *share)
+{
+	int ret;
+
+	ret = check_unshare(share);
+	if (ret)
+		return ret;
+
+	return WARN_ON(__do_unshare(share));
+}
+
+int __pkvm_host_share_hyp(u64 pfn)
+{
+	int ret;
+	u64 host_addr = hyp_pfn_to_phys(pfn);
+	u64 hyp_addr = (u64)__hyp_va(host_addr);
+	struct pkvm_mem_share share = {
+		.tx	= {
+			.nr_pages	= 1,
+			.initiator	= {
+				.id	= PKVM_ID_HOST,
+				.addr	= host_addr,
+				.host	= {
+					.completer_addr = hyp_addr,
+				},
+			},
+			.completer	= {
+				.id	= PKVM_ID_HYP,
+			},
+		},
+		.completer_prot	= PAGE_HYP,
+	};
+
+	host_lock_component();
+	hyp_lock_component();
+
+	ret = do_share(&share);
+
+	hyp_unlock_component();
+	host_unlock_component();
+
+	return ret;
+}
+
+int __pkvm_host_unshare_hyp(u64 pfn)
+{
+	int ret;
+	u64 host_addr = hyp_pfn_to_phys(pfn);
+	u64 hyp_addr = (u64)__hyp_va(host_addr);
+	struct pkvm_mem_share share = {
+		.tx	= {
+			.nr_pages	= 1,
+			.initiator	= {
+				.id	= PKVM_ID_HOST,
+				.addr	= host_addr,
+				.host	= {
+					.completer_addr = hyp_addr,
+				},
+			},
+			.completer	= {
+				.id	= PKVM_ID_HYP,
+			},
+		},
+		.completer_prot	= PAGE_HYP,
+	};
+
+	host_lock_component();
+	hyp_lock_component();
+
+	ret = do_unshare(&share);
+
+	hyp_unlock_component();
+	host_unlock_component();
+
+	return ret;
 }
diff --git a/arch/arm64/kvm/hyp/nvhe/mm.c b/arch/arm64/kvm/hyp/nvhe/mm.c
index 2fabeceb889a..96193cb31a39 100644
--- a/arch/arm64/kvm/hyp/nvhe/mm.c
+++ b/arch/arm64/kvm/hyp/nvhe/mm.c
@@ -8,6 +8,7 @@
 #include <asm/kvm_hyp.h>
 #include <asm/kvm_mmu.h>
 #include <asm/kvm_pgtable.h>
+#include <asm/kvm_pkvm.h>
 #include <asm/spectre.h>
 
 #include <nvhe/early_alloc.h>
@@ -18,11 +19,12 @@
 
 struct kvm_pgtable pkvm_pgtable;
 hyp_spinlock_t pkvm_pgd_lock;
-u64 __io_map_base;
 
 struct memblock_region hyp_memory[HYP_MEMBLOCK_REGIONS];
 unsigned int hyp_memblock_nr;
 
+static u64 __io_map_base;
+
 static int __pkvm_create_mappings(unsigned long start, unsigned long size,
 				  unsigned long phys, enum kvm_pgtable_prot prot)
 {
@@ -35,36 +37,60 @@ static int __pkvm_create_mappings(unsigned long start, unsigned long size,
 	return err;
 }
 
-unsigned long __pkvm_create_private_mapping(phys_addr_t phys, size_t size,
-					    enum kvm_pgtable_prot prot)
+/**
+ * pkvm_alloc_private_va_range - Allocates a private VA range.
+ * @size:	The size of the VA range to reserve.
+ * @haddr:	The hypervisor virtual start address of the allocation.
+ *
+ * The private virtual address (VA) range is allocated above __io_map_base
+ * and aligned based on the order of @size.
+ *
+ * Return: 0 on success or negative error code on failure.
+ */
+int pkvm_alloc_private_va_range(size_t size, unsigned long *haddr)
 {
-	unsigned long addr;
-	int err;
+	unsigned long base, addr;
+	int ret = 0;
 
 	hyp_spin_lock(&pkvm_pgd_lock);
 
-	size = PAGE_ALIGN(size + offset_in_page(phys));
-	addr = __io_map_base;
-	__io_map_base += size;
+	/* Align the allocation based on the order of its size */
+	addr = ALIGN(__io_map_base, PAGE_SIZE << get_order(size));
 
-	/* Are we overflowing on the vmemmap ? */
-	if (__io_map_base > __hyp_vmemmap) {
-		__io_map_base -= size;
-		addr = (unsigned long)ERR_PTR(-ENOMEM);
-		goto out;
-	}
+	/* The allocated size is always a multiple of PAGE_SIZE */
+	base = addr + PAGE_ALIGN(size);
 
-	err = kvm_pgtable_hyp_map(&pkvm_pgtable, addr, size, phys, prot);
-	if (err) {
-		addr = (unsigned long)ERR_PTR(err);
-		goto out;
+	/* Are we overflowing on the vmemmap ? */
+	if (!addr || base > __hyp_vmemmap)
+		ret = -ENOMEM;
+	else {
+		__io_map_base = base;
+		*haddr = addr;
 	}
 
-	addr = addr + offset_in_page(phys);
-out:
 	hyp_spin_unlock(&pkvm_pgd_lock);
 
-	return addr;
+	return ret;
+}
+
+int __pkvm_create_private_mapping(phys_addr_t phys, size_t size,
+				  enum kvm_pgtable_prot prot,
+				  unsigned long *haddr)
+{
+	unsigned long addr;
+	int err;
+
+	size = PAGE_ALIGN(size + offset_in_page(phys));
+	err = pkvm_alloc_private_va_range(size, &addr);
+	if (err)
+		return err;
+
+	err = __pkvm_create_mappings(addr, size, phys, prot);
+	if (err)
+		return err;
+
+	*haddr = addr + offset_in_page(phys);
+	return err;
 }
 
 int pkvm_create_mappings_locked(void *from, void *to, enum kvm_pgtable_prot prot)
@@ -144,19 +170,21 @@ int pkvm_cpu_set_vector(enum arm64_hyp_spectre_vector slot)
 int hyp_map_vectors(void)
 {
 	phys_addr_t phys;
-	void *bp_base;
+	unsigned long bp_base;
+	int ret;
 
-	if (!cpus_have_const_cap(ARM64_SPECTRE_V3A))
+	if (!kvm_system_needs_idmapped_vectors()) {
+		__hyp_bp_vect_base = __bp_harden_hyp_vecs;
 		return 0;
+	}
 
 	phys = __hyp_pa(__bp_harden_hyp_vecs);
-	bp_base = (void *)__pkvm_create_private_mapping(phys,
-							__BP_HARDEN_HYP_VECS_SZ,
-							PAGE_HYP_EXEC);
-	if (IS_ERR_OR_NULL(bp_base))
-		return PTR_ERR(bp_base);
+	ret = __pkvm_create_private_mapping(phys, __BP_HARDEN_HYP_VECS_SZ,
+					    PAGE_HYP_EXEC, &bp_base);
+	if (ret)
+		return ret;
 
-	__hyp_bp_vect_base = bp_base;
+	__hyp_bp_vect_base = (void *)bp_base;
 
 	return 0;
 }
diff --git a/arch/arm64/kvm/hyp/nvhe/page_alloc.c b/arch/arm64/kvm/hyp/nvhe/page_alloc.c
index 0bd7701ad1df..d40f0b30b534 100644
--- a/arch/arm64/kvm/hyp/nvhe/page_alloc.c
+++ b/arch/arm64/kvm/hyp/nvhe/page_alloc.c
@@ -102,7 +102,7 @@ static void __hyp_attach_page(struct hyp_pool *pool,
 	 * Only the first struct hyp_page of a high-order page (otherwise known
 	 * as the 'head') should have p->order set. The non-head pages should
 	 * have p->order = HYP_NO_ORDER. Here @p may no longer be the head
-	 * after coallescing, so make sure to mark it HYP_NO_ORDER proactively.
+	 * after coalescing, so make sure to mark it HYP_NO_ORDER proactively.
 	 */
 	p->order = HYP_NO_ORDER;
 	for (; (order + 1) < pool->max_order; order++) {
@@ -110,7 +110,7 @@ static void __hyp_attach_page(struct hyp_pool *pool,
 		if (!buddy)
 			break;
 
-		/* Take the buddy out of its list, and coallesce with @p */
+		/* Take the buddy out of its list, and coalesce with @p */
 		page_remove_from_list(buddy);
 		buddy->order = HYP_NO_ORDER;
 		p = min(p, buddy);
@@ -241,7 +241,7 @@ int hyp_pool_init(struct hyp_pool *pool, u64 pfn, unsigned int nr_pages,
 	int i;
 
 	hyp_spin_lock_init(&pool->lock);
-	pool->max_order = min(MAX_ORDER, get_order(nr_pages << PAGE_SHIFT));
+	pool->max_order = min(MAX_ORDER, get_order((nr_pages + 1) << PAGE_SHIFT));
 	for (i = 0; i < pool->max_order; i++)
 		INIT_LIST_HEAD(&pool->free_area[i]);
 	pool->range_start = phys;
diff --git a/arch/arm64/kvm/hyp/nvhe/pkvm.c b/arch/arm64/kvm/hyp/nvhe/pkvm.c
index 99c8d8b73e70..85d3b7ae720f 100644
--- a/arch/arm64/kvm/hyp/nvhe/pkvm.c
+++ b/arch/arm64/kvm/hyp/nvhe/pkvm.c
@@ -20,35 +20,35 @@ static void pvm_init_traps_aa64pfr0(struct kvm_vcpu *vcpu)
 	u64 cptr_set = 0;
 
 	/* Protected KVM does not support AArch32 guests. */
-	BUILD_BUG_ON(FIELD_GET(ARM64_FEATURE_MASK(ID_AA64PFR0_EL0),
-		PVM_ID_AA64PFR0_RESTRICT_UNSIGNED) != ID_AA64PFR0_ELx_64BIT_ONLY);
-	BUILD_BUG_ON(FIELD_GET(ARM64_FEATURE_MASK(ID_AA64PFR0_EL1),
-		PVM_ID_AA64PFR0_RESTRICT_UNSIGNED) != ID_AA64PFR0_ELx_64BIT_ONLY);
+	BUILD_BUG_ON(FIELD_GET(ARM64_FEATURE_MASK(ID_AA64PFR0_EL1_EL0),
+		PVM_ID_AA64PFR0_RESTRICT_UNSIGNED) != ID_AA64PFR0_EL1_ELx_64BIT_ONLY);
+	BUILD_BUG_ON(FIELD_GET(ARM64_FEATURE_MASK(ID_AA64PFR0_EL1_EL1),
+		PVM_ID_AA64PFR0_RESTRICT_UNSIGNED) != ID_AA64PFR0_EL1_ELx_64BIT_ONLY);
 
 	/*
 	 * Linux guests assume support for floating-point and Advanced SIMD. Do
 	 * not change the trapping behavior for these from the KVM default.
 	 */
-	BUILD_BUG_ON(!FIELD_GET(ARM64_FEATURE_MASK(ID_AA64PFR0_FP),
+	BUILD_BUG_ON(!FIELD_GET(ARM64_FEATURE_MASK(ID_AA64PFR0_EL1_FP),
 				PVM_ID_AA64PFR0_ALLOW));
-	BUILD_BUG_ON(!FIELD_GET(ARM64_FEATURE_MASK(ID_AA64PFR0_ASIMD),
+	BUILD_BUG_ON(!FIELD_GET(ARM64_FEATURE_MASK(ID_AA64PFR0_EL1_AdvSIMD),
 				PVM_ID_AA64PFR0_ALLOW));
 
 	/* Trap RAS unless all current versions are supported */
-	if (FIELD_GET(ARM64_FEATURE_MASK(ID_AA64PFR0_RAS), feature_ids) <
-	    ID_AA64PFR0_RAS_V1P1) {
+	if (FIELD_GET(ARM64_FEATURE_MASK(ID_AA64PFR0_EL1_RAS), feature_ids) <
+	    ID_AA64PFR0_EL1_RAS_V1P1) {
 		hcr_set |= HCR_TERR | HCR_TEA;
 		hcr_clear |= HCR_FIEN;
 	}
 
 	/* Trap AMU */
-	if (!FIELD_GET(ARM64_FEATURE_MASK(ID_AA64PFR0_AMU), feature_ids)) {
+	if (!FIELD_GET(ARM64_FEATURE_MASK(ID_AA64PFR0_EL1_AMU), feature_ids)) {
 		hcr_clear |= HCR_AMVOFFEN;
 		cptr_set |= CPTR_EL2_TAM;
 	}
 
 	/* Trap SVE */
-	if (!FIELD_GET(ARM64_FEATURE_MASK(ID_AA64PFR0_SVE), feature_ids))
+	if (!FIELD_GET(ARM64_FEATURE_MASK(ID_AA64PFR0_EL1_SVE), feature_ids))
 		cptr_set |= CPTR_EL2_TZ;
 
 	vcpu->arch.hcr_el2 |= hcr_set;
@@ -66,7 +66,7 @@ static void pvm_init_traps_aa64pfr1(struct kvm_vcpu *vcpu)
 	u64 hcr_clear = 0;
 
 	/* Memory Tagging: Trap and Treat as Untagged if not supported. */
-	if (!FIELD_GET(ARM64_FEATURE_MASK(ID_AA64PFR1_MTE), feature_ids)) {
+	if (!FIELD_GET(ARM64_FEATURE_MASK(ID_AA64PFR1_EL1_MTE), feature_ids)) {
 		hcr_set |= HCR_TID5;
 		hcr_clear |= HCR_DCT | HCR_ATA;
 	}
@@ -86,32 +86,32 @@ static void pvm_init_traps_aa64dfr0(struct kvm_vcpu *vcpu)
 	u64 cptr_set = 0;
 
 	/* Trap/constrain PMU */
-	if (!FIELD_GET(ARM64_FEATURE_MASK(ID_AA64DFR0_PMUVER), feature_ids)) {
+	if (!FIELD_GET(ARM64_FEATURE_MASK(ID_AA64DFR0_EL1_PMUVer), feature_ids)) {
 		mdcr_set |= MDCR_EL2_TPM | MDCR_EL2_TPMCR;
 		mdcr_clear |= MDCR_EL2_HPME | MDCR_EL2_MTPME |
 			      MDCR_EL2_HPMN_MASK;
 	}
 
 	/* Trap Debug */
-	if (!FIELD_GET(ARM64_FEATURE_MASK(ID_AA64DFR0_DEBUGVER), feature_ids))
+	if (!FIELD_GET(ARM64_FEATURE_MASK(ID_AA64DFR0_EL1_DebugVer), feature_ids))
 		mdcr_set |= MDCR_EL2_TDRA | MDCR_EL2_TDA | MDCR_EL2_TDE;
 
 	/* Trap OS Double Lock */
-	if (!FIELD_GET(ARM64_FEATURE_MASK(ID_AA64DFR0_DOUBLELOCK), feature_ids))
+	if (!FIELD_GET(ARM64_FEATURE_MASK(ID_AA64DFR0_EL1_DoubleLock), feature_ids))
 		mdcr_set |= MDCR_EL2_TDOSA;
 
 	/* Trap SPE */
-	if (!FIELD_GET(ARM64_FEATURE_MASK(ID_AA64DFR0_PMSVER), feature_ids)) {
+	if (!FIELD_GET(ARM64_FEATURE_MASK(ID_AA64DFR0_EL1_PMSVer), feature_ids)) {
 		mdcr_set |= MDCR_EL2_TPMS;
 		mdcr_clear |= MDCR_EL2_E2PB_MASK << MDCR_EL2_E2PB_SHIFT;
 	}
 
 	/* Trap Trace Filter */
-	if (!FIELD_GET(ARM64_FEATURE_MASK(ID_AA64DFR0_TRACE_FILT), feature_ids))
+	if (!FIELD_GET(ARM64_FEATURE_MASK(ID_AA64DFR0_EL1_TraceFilt), feature_ids))
 		mdcr_set |= MDCR_EL2_TTRF;
 
 	/* Trap Trace */
-	if (!FIELD_GET(ARM64_FEATURE_MASK(ID_AA64DFR0_TRACEVER), feature_ids))
+	if (!FIELD_GET(ARM64_FEATURE_MASK(ID_AA64DFR0_EL1_TraceVer), feature_ids))
 		cptr_set |= CPTR_EL2_TTA;
 
 	vcpu->arch.mdcr_el2 |= mdcr_set;
@@ -128,7 +128,7 @@ static void pvm_init_traps_aa64mmfr0(struct kvm_vcpu *vcpu)
 	u64 mdcr_set = 0;
 
 	/* Trap Debug Communications Channel registers */
-	if (!FIELD_GET(ARM64_FEATURE_MASK(ID_AA64MMFR0_FGT), feature_ids))
+	if (!FIELD_GET(ARM64_FEATURE_MASK(ID_AA64MMFR0_EL1_FGT), feature_ids))
 		mdcr_set |= MDCR_EL2_TDCC;
 
 	vcpu->arch.mdcr_el2 |= mdcr_set;
@@ -143,7 +143,7 @@ static void pvm_init_traps_aa64mmfr1(struct kvm_vcpu *vcpu)
 	u64 hcr_set = 0;
 
 	/* Trap LOR */
-	if (!FIELD_GET(ARM64_FEATURE_MASK(ID_AA64MMFR1_LOR), feature_ids))
+	if (!FIELD_GET(ARM64_FEATURE_MASK(ID_AA64MMFR1_EL1_LO), feature_ids))
 		hcr_set |= HCR_TLOR;
 
 	vcpu->arch.hcr_el2 |= hcr_set;
diff --git a/arch/arm64/kvm/hyp/nvhe/setup.c b/arch/arm64/kvm/hyp/nvhe/setup.c
index 578f71798c2e..e8d4ea2fcfa0 100644
--- a/arch/arm64/kvm/hyp/nvhe/setup.c
+++ b/arch/arm64/kvm/hyp/nvhe/setup.c
@@ -8,6 +8,7 @@
 #include <asm/kvm_hyp.h>
 #include <asm/kvm_mmu.h>
 #include <asm/kvm_pgtable.h>
+#include <asm/kvm_pkvm.h>
 
 #include <nvhe/early_alloc.h>
 #include <nvhe/fixed_config.h>
@@ -17,7 +18,6 @@
 #include <nvhe/mm.h>
 #include <nvhe/trap_handler.h>
 
-struct hyp_pool hpool;
 unsigned long hyp_nr_cpus;
 
 #define hyp_percpu_size ((unsigned long)__per_cpu_end - \
@@ -27,6 +27,7 @@ static void *vmemmap_base;
 static void *hyp_pgt_base;
 static void *host_s2_pgt_base;
 static struct kvm_pgtable_mm_ops pkvm_pgtable_mm_ops;
+static struct hyp_pool hpool;
 
 static int divide_memory_pool(void *virt, unsigned long size)
 {
@@ -98,17 +99,42 @@ static int recreate_hyp_mappings(phys_addr_t phys, unsigned long size,
 		return ret;
 
 	for (i = 0; i < hyp_nr_cpus; i++) {
+		struct kvm_nvhe_init_params *params = per_cpu_ptr(&kvm_init_params, i);
+		unsigned long hyp_addr;
+
 		start = (void *)kern_hyp_va(per_cpu_base[i]);
 		end = start + PAGE_ALIGN(hyp_percpu_size);
 		ret = pkvm_create_mappings(start, end, PAGE_HYP);
 		if (ret)
 			return ret;
 
-		end = (void *)per_cpu_ptr(&kvm_init_params, i)->stack_hyp_va;
-		start = end - PAGE_SIZE;
-		ret = pkvm_create_mappings(start, end, PAGE_HYP);
+		/*
+		 * Allocate a contiguous HYP private VA range for the stack
+		 * and guard page. The allocation is also aligned based on
+		 * the order of its size.
+		 */
+		ret = pkvm_alloc_private_va_range(PAGE_SIZE * 2, &hyp_addr);
+		if (ret)
+			return ret;
+
+		/*
+		 * Since the stack grows downwards, map the stack to the page
+		 * at the higher address and leave the lower guard page
+		 * unbacked.
+		 *
+		 * Any valid stack address now has the PAGE_SHIFT bit as 1
+		 * and addresses corresponding to the guard page have the
+		 * PAGE_SHIFT bit as 0 - this is used for overflow detection.
+		 */
+		hyp_spin_lock(&pkvm_pgd_lock);
+		ret = kvm_pgtable_hyp_map(&pkvm_pgtable, hyp_addr + PAGE_SIZE,
+					PAGE_SIZE, params->stack_pa, PAGE_HYP);
+		hyp_spin_unlock(&pkvm_pgd_lock);
 		if (ret)
 			return ret;
+
+		/* Update stack_hyp_va to end of the stack's private VA range */
+		params->stack_hyp_va = hyp_addr + (2 * PAGE_SIZE);
 	}
 
 	/*
@@ -165,6 +191,7 @@ static int finalize_host_mappings_walker(u64 addr, u64 end, u32 level,
 					 enum kvm_pgtable_walk_flags flag,
 					 void * const arg)
 {
+	struct kvm_pgtable_mm_ops *mm_ops = arg;
 	enum kvm_pgtable_prot prot;
 	enum pkvm_page_state state;
 	kvm_pte_t pte = *ptep;
@@ -173,6 +200,15 @@ static int finalize_host_mappings_walker(u64 addr, u64 end, u32 level,
 	if (!kvm_pte_valid(pte))
 		return 0;
 
+	/*
+	 * Fix-up the refcount for the page-table pages as the early allocator
+	 * was unable to access the hyp_vmemmap and so the buddy allocator has
+	 * initialised the refcount to '1'.
+	 */
+	mm_ops->get_page(ptep);
+	if (flag != KVM_PGTABLE_WALK_LEAF)
+		return 0;
+
 	if (level != (KVM_PGTABLE_MAX_LEVELS - 1))
 		return -EINVAL;
 
@@ -205,7 +241,8 @@ static int finalize_host_mappings(void)
 {
 	struct kvm_pgtable_walker walker = {
 		.cb	= finalize_host_mappings_walker,
-		.flags	= KVM_PGTABLE_WALK_LEAF,
+		.flags	= KVM_PGTABLE_WALK_LEAF | KVM_PGTABLE_WALK_TABLE_POST,
+		.arg	= pkvm_pgtable.mm_ops,
 	};
 	int i, ret;
 
@@ -240,19 +277,20 @@ void __noreturn __pkvm_init_finalise(void)
 	if (ret)
 		goto out;
 
-	ret = finalize_host_mappings();
-	if (ret)
-		goto out;
-
 	pkvm_pgtable_mm_ops = (struct kvm_pgtable_mm_ops) {
 		.zalloc_page = hyp_zalloc_hyp_page,
 		.phys_to_virt = hyp_phys_to_virt,
 		.virt_to_phys = hyp_virt_to_phys,
 		.get_page = hpool_get_page,
 		.put_page = hpool_put_page,
+		.page_count = hyp_page_count,
 	};
 	pkvm_pgtable.mm_ops = &pkvm_pgtable_mm_ops;
 
+	ret = finalize_host_mappings();
+	if (ret)
+		goto out;
+
 out:
 	/*
 	 * We tail-called to here from handle___pkvm_init() and will not return,
diff --git a/arch/arm64/kvm/hyp/nvhe/stacktrace.c b/arch/arm64/kvm/hyp/nvhe/stacktrace.c
new file mode 100644
index 000000000000..ed6b58b19cfa
--- /dev/null
+++ b/arch/arm64/kvm/hyp/nvhe/stacktrace.c
@@ -0,0 +1,158 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * KVM nVHE hypervisor stack tracing support.
+ *
+ * Copyright (C) 2022 Google LLC
+ */
+#include <asm/kvm_asm.h>
+#include <asm/kvm_hyp.h>
+#include <asm/memory.h>
+#include <asm/percpu.h>
+
+DEFINE_PER_CPU(unsigned long [OVERFLOW_STACK_SIZE/sizeof(long)], overflow_stack)
+	__aligned(16);
+
+DEFINE_PER_CPU(struct kvm_nvhe_stacktrace_info, kvm_stacktrace_info);
+
+/*
+ * hyp_prepare_backtrace - Prepare non-protected nVHE backtrace.
+ *
+ * @fp : frame pointer at which to start the unwinding.
+ * @pc : program counter at which to start the unwinding.
+ *
+ * Save the information needed by the host to unwind the non-protected
+ * nVHE hypervisor stack in EL1.
+ */
+static void hyp_prepare_backtrace(unsigned long fp, unsigned long pc)
+{
+	struct kvm_nvhe_stacktrace_info *stacktrace_info = this_cpu_ptr(&kvm_stacktrace_info);
+	struct kvm_nvhe_init_params *params = this_cpu_ptr(&kvm_init_params);
+
+	stacktrace_info->stack_base = (unsigned long)(params->stack_hyp_va - PAGE_SIZE);
+	stacktrace_info->overflow_stack_base = (unsigned long)this_cpu_ptr(overflow_stack);
+	stacktrace_info->fp = fp;
+	stacktrace_info->pc = pc;
+}
+
+#ifdef CONFIG_PROTECTED_NVHE_STACKTRACE
+#include <asm/stacktrace/nvhe.h>
+
+DEFINE_PER_CPU(unsigned long [NVHE_STACKTRACE_SIZE/sizeof(long)], pkvm_stacktrace);
+
+static struct stack_info stackinfo_get_overflow(void)
+{
+	unsigned long low = (unsigned long)this_cpu_ptr(overflow_stack);
+	unsigned long high = low + OVERFLOW_STACK_SIZE;
+
+	return (struct stack_info) {
+		.low = low,
+		.high = high,
+	};
+}
+
+static struct stack_info stackinfo_get_hyp(void)
+{
+	struct kvm_nvhe_init_params *params = this_cpu_ptr(&kvm_init_params);
+	unsigned long high = params->stack_hyp_va;
+	unsigned long low = high - PAGE_SIZE;
+
+	return (struct stack_info) {
+		.low = low,
+		.high = high,
+	};
+}
+
+static int unwind_next(struct unwind_state *state)
+{
+	return unwind_next_frame_record(state);
+}
+
+static void notrace unwind(struct unwind_state *state,
+			   stack_trace_consume_fn consume_entry,
+			   void *cookie)
+{
+	while (1) {
+		int ret;
+
+		if (!consume_entry(cookie, state->pc))
+			break;
+		ret = unwind_next(state);
+		if (ret < 0)
+			break;
+	}
+}
+
+/*
+ * pkvm_save_backtrace_entry - Saves a protected nVHE HYP stacktrace entry
+ *
+ * @arg    : index of the entry in the stacktrace buffer
+ * @where  : the program counter corresponding to the stack frame
+ *
+ * Save the return address of a stack frame to the shared stacktrace buffer.
+ * The host can access this shared buffer from EL1 to dump the backtrace.
+ */
+static bool pkvm_save_backtrace_entry(void *arg, unsigned long where)
+{
+	unsigned long *stacktrace = this_cpu_ptr(pkvm_stacktrace);
+	int *idx = (int *)arg;
+
+	/*
+	 * Need 2 free slots: 1 for current entry and 1 for the
+	 * delimiter.
+	 */
+	if (*idx > ARRAY_SIZE(pkvm_stacktrace) - 2)
+		return false;
+
+	stacktrace[*idx] = where;
+	stacktrace[++*idx] = 0UL;
+
+	return true;
+}
+
+/*
+ * pkvm_save_backtrace - Saves the protected nVHE HYP stacktrace
+ *
+ * @fp : frame pointer at which to start the unwinding.
+ * @pc : program counter at which to start the unwinding.
+ *
+ * Save the unwinded stack addresses to the shared stacktrace buffer.
+ * The host can access this shared buffer from EL1 to dump the backtrace.
+ */
+static void pkvm_save_backtrace(unsigned long fp, unsigned long pc)
+{
+	struct stack_info stacks[] = {
+		stackinfo_get_overflow(),
+		stackinfo_get_hyp(),
+	};
+	struct unwind_state state = {
+		.stacks = stacks,
+		.nr_stacks = ARRAY_SIZE(stacks),
+	};
+	int idx = 0;
+
+	kvm_nvhe_unwind_init(&state, fp, pc);
+
+	unwind(&state, pkvm_save_backtrace_entry, &idx);
+}
+#else /* !CONFIG_PROTECTED_NVHE_STACKTRACE */
+static void pkvm_save_backtrace(unsigned long fp, unsigned long pc)
+{
+}
+#endif /* CONFIG_PROTECTED_NVHE_STACKTRACE */
+
+/*
+ * kvm_nvhe_prepare_backtrace - prepare to dump the nVHE backtrace
+ *
+ * @fp : frame pointer at which to start the unwinding.
+ * @pc : program counter at which to start the unwinding.
+ *
+ * Saves the information needed by the host to dump the nVHE hypervisor
+ * backtrace.
+ */
+void kvm_nvhe_prepare_backtrace(unsigned long fp, unsigned long pc)
+{
+	if (is_protected_kvm_enabled())
+		pkvm_save_backtrace(fp, pc);
+	else
+		hyp_prepare_backtrace(fp, pc);
+}
diff --git a/arch/arm64/kvm/hyp/nvhe/stub.c b/arch/arm64/kvm/hyp/nvhe/stub.c
deleted file mode 100644
index c0aa6bbfd79d..000000000000
--- a/arch/arm64/kvm/hyp/nvhe/stub.c
+++ /dev/null
@@ -1,22 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Stubs for out-of-line function calls caused by re-using kernel
- * infrastructure at EL2.
- *
- * Copyright (C) 2020 - Google LLC
- */
-
-#include <linux/list.h>
-
-#ifdef CONFIG_DEBUG_LIST
-bool __list_add_valid(struct list_head *new, struct list_head *prev,
-		      struct list_head *next)
-{
-		return true;
-}
-
-bool __list_del_entry_valid(struct list_head *entry)
-{
-		return true;
-}
-#endif
diff --git a/arch/arm64/kvm/hyp/nvhe/switch.c b/arch/arm64/kvm/hyp/nvhe/switch.c
index d13115a12434..c2cb46ca4fb6 100644
--- a/arch/arm64/kvm/hyp/nvhe/switch.c
+++ b/arch/arm64/kvm/hyp/nvhe/switch.c
@@ -25,7 +25,6 @@
 #include <asm/fpsimd.h>
 #include <asm/debug-monitors.h>
 #include <asm/processor.h>
-#include <asm/thread_info.h>
 
 #include <nvhe/fixed_config.h>
 #include <nvhe/mem_protect.h>
@@ -35,6 +34,8 @@ DEFINE_PER_CPU(struct kvm_host_data, kvm_host_data);
 DEFINE_PER_CPU(struct kvm_cpu_context, kvm_hyp_ctxt);
 DEFINE_PER_CPU(unsigned long, kvm_hyp_vector);
 
+extern void kvm_nvhe_prepare_backtrace(unsigned long fp, unsigned long pc);
+
 static void __activate_traps(struct kvm_vcpu *vcpu)
 {
 	u64 val;
@@ -44,10 +45,12 @@ static void __activate_traps(struct kvm_vcpu *vcpu)
 
 	val = vcpu->arch.cptr_el2;
 	val |= CPTR_EL2_TTA | CPTR_EL2_TAM;
-	if (!update_fp_enabled(vcpu)) {
+	if (!guest_owns_fp_regs(vcpu)) {
 		val |= CPTR_EL2_TFP | CPTR_EL2_TZ;
 		__activate_traps_fpsimd32(vcpu);
 	}
+	if (cpus_have_final_cap(ARM64_SME))
+		val |= CPTR_EL2_TSM;
 
 	write_sysreg(val, cptr_el2);
 	write_sysreg(__this_cpu_read(kvm_hyp_vector), vbar_el2);
@@ -96,8 +99,10 @@ static void __deactivate_traps(struct kvm_vcpu *vcpu)
 	write_sysreg(this_cpu_ptr(&kvm_init_params)->hcr_el2, hcr_el2);
 
 	cptr = CPTR_EL2_DEFAULT;
-	if (vcpu_has_sve(vcpu) && (vcpu->arch.flags & KVM_ARM64_FP_ENABLED))
+	if (vcpu_has_sve(vcpu) && (vcpu->arch.fp_state == FP_STATE_GUEST_OWNED))
 		cptr |= CPTR_EL2_TZ;
+	if (cpus_have_final_cap(ARM64_SME))
+		cptr &= ~CPTR_EL2_TSM;
 
 	write_sysreg(cptr, cptr_el2);
 	write_sysreg(__kvm_hyp_host_vector, vbar_el2);
@@ -112,7 +117,7 @@ static void __hyp_vgic_save_state(struct kvm_vcpu *vcpu)
 	}
 }
 
-/* Restore VGICv3 state on non_VEH systems */
+/* Restore VGICv3 state on non-VHE systems */
 static void __hyp_vgic_restore_state(struct kvm_vcpu *vcpu)
 {
 	if (static_branch_unlikely(&kvm_vgic_global_state.gicv3_cpuif)) {
@@ -121,16 +126,13 @@ static void __hyp_vgic_restore_state(struct kvm_vcpu *vcpu)
 	}
 }
 
-/**
+/*
  * Disable host events, enable guest events
  */
-static bool __pmu_switch_to_guest(struct kvm_cpu_context *host_ctxt)
+#ifdef CONFIG_HW_PERF_EVENTS
+static bool __pmu_switch_to_guest(struct kvm_vcpu *vcpu)
 {
-	struct kvm_host_data *host;
-	struct kvm_pmu_events *pmu;
-
-	host = container_of(host_ctxt, struct kvm_host_data, host_ctxt);
-	pmu = &host->pmu_events;
+	struct kvm_pmu_events *pmu = &vcpu->arch.pmu.events;
 
 	if (pmu->events_host)
 		write_sysreg(pmu->events_host, pmcntenclr_el0);
@@ -141,16 +143,12 @@ static bool __pmu_switch_to_guest(struct kvm_cpu_context *host_ctxt)
 	return (pmu->events_host || pmu->events_guest);
 }
 
-/**
+/*
  * Disable guest events, enable host events
  */
-static void __pmu_switch_to_host(struct kvm_cpu_context *host_ctxt)
+static void __pmu_switch_to_host(struct kvm_vcpu *vcpu)
 {
-	struct kvm_host_data *host;
-	struct kvm_pmu_events *pmu;
-
-	host = container_of(host_ctxt, struct kvm_host_data, host_ctxt);
-	pmu = &host->pmu_events;
+	struct kvm_pmu_events *pmu = &vcpu->arch.pmu.events;
 
 	if (pmu->events_guest)
 		write_sysreg(pmu->events_guest, pmcntenclr_el0);
@@ -158,8 +156,12 @@ static void __pmu_switch_to_host(struct kvm_cpu_context *host_ctxt)
 	if (pmu->events_host)
 		write_sysreg(pmu->events_host, pmcntenset_el0);
 }
+#else
+#define __pmu_switch_to_guest(v)	({ false; })
+#define __pmu_switch_to_host(v)		do {} while (0)
+#endif
 
-/**
+/*
  * Handler for protected VM MSR, MRS or System instruction execution in AArch64.
  *
  * Returns true if the hypervisor has handled the exit, and control should go
@@ -176,23 +178,6 @@ static bool kvm_handle_pvm_sys64(struct kvm_vcpu *vcpu, u64 *exit_code)
 		kvm_handle_pvm_sysreg(vcpu, exit_code));
 }
 
-/**
- * Handler for protected floating-point and Advanced SIMD accesses.
- *
- * Returns true if the hypervisor has handled the exit, and control should go
- * back to the guest, or false if it hasn't.
- */
-static bool kvm_handle_pvm_fpsimd(struct kvm_vcpu *vcpu, u64 *exit_code)
-{
-	/* Linux guests assume support for floating-point and Advanced SIMD. */
-	BUILD_BUG_ON(!FIELD_GET(ARM64_FEATURE_MASK(ID_AA64PFR0_FP),
-				PVM_ID_AA64PFR0_ALLOW));
-	BUILD_BUG_ON(!FIELD_GET(ARM64_FEATURE_MASK(ID_AA64PFR0_ASIMD),
-				PVM_ID_AA64PFR0_ALLOW));
-
-	return kvm_hyp_handle_fpsimd(vcpu, exit_code);
-}
-
 static const exit_handler_fn hyp_exit_handlers[] = {
 	[0 ... ESR_ELx_EC_MAX]		= NULL,
 	[ESR_ELx_EC_CP15_32]		= kvm_hyp_handle_cp15_32,
@@ -208,7 +193,7 @@ static const exit_handler_fn pvm_exit_handlers[] = {
 	[0 ... ESR_ELx_EC_MAX]		= NULL,
 	[ESR_ELx_EC_SYS64]		= kvm_handle_pvm_sys64,
 	[ESR_ELx_EC_SVE]		= kvm_handle_pvm_restricted,
-	[ESR_ELx_EC_FP_ASIMD]		= kvm_handle_pvm_fpsimd,
+	[ESR_ELx_EC_FP_ASIMD]		= kvm_hyp_handle_fpsimd,
 	[ESR_ELx_EC_IABT_LOW]		= kvm_hyp_handle_iabt_low,
 	[ESR_ELx_EC_DABT_LOW]		= kvm_hyp_handle_dabt_low,
 	[ESR_ELx_EC_PAC]		= kvm_hyp_handle_ptrauth,
@@ -275,7 +260,7 @@ int __kvm_vcpu_run(struct kvm_vcpu *vcpu)
 	host_ctxt->__hyp_running_vcpu = vcpu;
 	guest_ctxt = &vcpu->arch.ctxt;
 
-	pmu_switch_needed = __pmu_switch_to_guest(host_ctxt);
+	pmu_switch_needed = __pmu_switch_to_guest(vcpu);
 
 	__sysreg_save_state_nvhe(host_ctxt);
 	/*
@@ -326,7 +311,7 @@ int __kvm_vcpu_run(struct kvm_vcpu *vcpu)
 
 	__sysreg_restore_state_nvhe(host_ctxt);
 
-	if (vcpu->arch.flags & KVM_ARM64_FP_ENABLED)
+	if (vcpu->arch.fp_state == FP_STATE_GUEST_OWNED)
 		__fpsimd_save_fpexc32(vcpu);
 
 	__debug_switch_to_host(vcpu);
@@ -337,7 +322,7 @@ int __kvm_vcpu_run(struct kvm_vcpu *vcpu)
 	__debug_restore_host_buffers_nvhe(vcpu);
 
 	if (pmu_switch_needed)
-		__pmu_switch_to_host(host_ctxt);
+		__pmu_switch_to_host(vcpu);
 
 	/* Returning to host will clear PSR.I, remask PMR if needed */
 	if (system_uses_irq_prio_masking())
@@ -348,7 +333,7 @@ int __kvm_vcpu_run(struct kvm_vcpu *vcpu)
 	return exit_code;
 }
 
-void __noreturn hyp_panic(void)
+asmlinkage void __noreturn hyp_panic(void)
 {
 	u64 spsr = read_sysreg_el2(SYS_SPSR);
 	u64 elr = read_sysreg_el2(SYS_ELR);
@@ -366,11 +351,20 @@ void __noreturn hyp_panic(void)
 		__sysreg_restore_state_nvhe(host_ctxt);
 	}
 
+	/* Prepare to dump kvm nvhe hyp stacktrace */
+	kvm_nvhe_prepare_backtrace((unsigned long)__builtin_frame_address(0),
+				   _THIS_IP_);
+
 	__hyp_do_panic(host_ctxt, spsr, elr, par);
 	unreachable();
 }
 
+asmlinkage void __noreturn hyp_panic_bad_stack(void)
+{
+	hyp_panic();
+}
+
 asmlinkage void kvm_unexpected_el2_exception(void)
 {
-	return __kvm_unexpected_el2_exception();
+	__kvm_unexpected_el2_exception();
 }
diff --git a/arch/arm64/kvm/hyp/nvhe/sys_regs.c b/arch/arm64/kvm/hyp/nvhe/sys_regs.c
index 792cf6e6ac92..0f9ac25afdf4 100644
--- a/arch/arm64/kvm/hyp/nvhe/sys_regs.c
+++ b/arch/arm64/kvm/hyp/nvhe/sys_regs.c
@@ -22,6 +22,7 @@ u64 id_aa64pfr0_el1_sys_val;
 u64 id_aa64pfr1_el1_sys_val;
 u64 id_aa64isar0_el1_sys_val;
 u64 id_aa64isar1_el1_sys_val;
+u64 id_aa64isar2_el1_sys_val;
 u64 id_aa64mmfr0_el1_sys_val;
 u64 id_aa64mmfr1_el1_sys_val;
 u64 id_aa64mmfr2_el1_sys_val;
@@ -32,14 +33,12 @@ u64 id_aa64mmfr2_el1_sys_val;
  */
 static void inject_undef64(struct kvm_vcpu *vcpu)
 {
-	u32 esr = (ESR_ELx_EC_UNKNOWN << ESR_ELx_EC_SHIFT);
+	u64 esr = (ESR_ELx_EC_UNKNOWN << ESR_ELx_EC_SHIFT);
 
 	*vcpu_pc(vcpu) = read_sysreg_el2(SYS_ELR);
 	*vcpu_cpsr(vcpu) = read_sysreg_el2(SYS_SPSR);
 
-	vcpu->arch.flags |= (KVM_ARM64_EXCEPT_AA64_EL1 |
-			     KVM_ARM64_EXCEPT_AA64_ELx_SYNC |
-			     KVM_ARM64_PENDING_EXCEPTION);
+	kvm_pend_exception(vcpu, EXCEPT_AA64_EL1_SYNC);
 
 	__kvm_adjust_pc(vcpu);
 
@@ -89,16 +88,13 @@ static u64 get_pvm_id_aa64pfr0(const struct kvm_vcpu *vcpu)
 	u64 set_mask = 0;
 	u64 allow_mask = PVM_ID_AA64PFR0_ALLOW;
 
-	if (!vcpu_has_sve(vcpu))
-		allow_mask &= ~ARM64_FEATURE_MASK(ID_AA64PFR0_SVE);
-
 	set_mask |= get_restricted_features_unsigned(id_aa64pfr0_el1_sys_val,
 		PVM_ID_AA64PFR0_RESTRICT_UNSIGNED);
 
 	/* Spectre and Meltdown mitigation in KVM */
-	set_mask |= FIELD_PREP(ARM64_FEATURE_MASK(ID_AA64PFR0_CSV2),
+	set_mask |= FIELD_PREP(ARM64_FEATURE_MASK(ID_AA64PFR0_EL1_CSV2),
 			       (u64)kvm->arch.pfr0_csv2);
-	set_mask |= FIELD_PREP(ARM64_FEATURE_MASK(ID_AA64PFR0_CSV3),
+	set_mask |= FIELD_PREP(ARM64_FEATURE_MASK(ID_AA64PFR0_EL1_CSV3),
 			       (u64)kvm->arch.pfr0_csv3);
 
 	return (id_aa64pfr0_el1_sys_val & allow_mask) | set_mask;
@@ -110,7 +106,7 @@ static u64 get_pvm_id_aa64pfr1(const struct kvm_vcpu *vcpu)
 	u64 allow_mask = PVM_ID_AA64PFR1_ALLOW;
 
 	if (!kvm_has_mte(kvm))
-		allow_mask &= ~ARM64_FEATURE_MASK(ID_AA64PFR1_MTE);
+		allow_mask &= ~ARM64_FEATURE_MASK(ID_AA64PFR1_EL1_MTE);
 
 	return id_aa64pfr1_el1_sys_val & allow_mask;
 }
@@ -175,14 +171,25 @@ static u64 get_pvm_id_aa64isar1(const struct kvm_vcpu *vcpu)
 	u64 allow_mask = PVM_ID_AA64ISAR1_ALLOW;
 
 	if (!vcpu_has_ptrauth(vcpu))
-		allow_mask &= ~(ARM64_FEATURE_MASK(ID_AA64ISAR1_APA) |
-				ARM64_FEATURE_MASK(ID_AA64ISAR1_API) |
-				ARM64_FEATURE_MASK(ID_AA64ISAR1_GPA) |
-				ARM64_FEATURE_MASK(ID_AA64ISAR1_GPI));
+		allow_mask &= ~(ARM64_FEATURE_MASK(ID_AA64ISAR1_EL1_APA) |
+				ARM64_FEATURE_MASK(ID_AA64ISAR1_EL1_API) |
+				ARM64_FEATURE_MASK(ID_AA64ISAR1_EL1_GPA) |
+				ARM64_FEATURE_MASK(ID_AA64ISAR1_EL1_GPI));
 
 	return id_aa64isar1_el1_sys_val & allow_mask;
 }
 
+static u64 get_pvm_id_aa64isar2(const struct kvm_vcpu *vcpu)
+{
+	u64 allow_mask = PVM_ID_AA64ISAR2_ALLOW;
+
+	if (!vcpu_has_ptrauth(vcpu))
+		allow_mask &= ~(ARM64_FEATURE_MASK(ID_AA64ISAR2_EL1_APA3) |
+				ARM64_FEATURE_MASK(ID_AA64ISAR2_EL1_GPA3));
+
+	return id_aa64isar2_el1_sys_val & allow_mask;
+}
+
 static u64 get_pvm_id_aa64mmfr0(const struct kvm_vcpu *vcpu)
 {
 	u64 set_mask;
@@ -225,6 +232,8 @@ u64 pvm_read_id_reg(const struct kvm_vcpu *vcpu, u32 id)
 		return get_pvm_id_aa64isar0(vcpu);
 	case SYS_ID_AA64ISAR1_EL1:
 		return get_pvm_id_aa64isar1(vcpu);
+	case SYS_ID_AA64ISAR2_EL1:
+		return get_pvm_id_aa64isar2(vcpu);
 	case SYS_ID_AA64MMFR0_EL1:
 		return get_pvm_id_aa64mmfr0(vcpu);
 	case SYS_ID_AA64MMFR1_EL1:
@@ -232,15 +241,9 @@ u64 pvm_read_id_reg(const struct kvm_vcpu *vcpu, u32 id)
 	case SYS_ID_AA64MMFR2_EL1:
 		return get_pvm_id_aa64mmfr2(vcpu);
 	default:
-		/*
-		 * Should never happen because all cases are covered in
-		 * pvm_sys_reg_descs[].
-		 */
-		WARN_ON(1);
-		break;
+		/* Unhandled ID register, RAZ */
+		return 0;
 	}
-
-	return 0;
 }
 
 static u64 read_id_reg(const struct kvm_vcpu *vcpu,
@@ -278,8 +281,8 @@ static bool pvm_access_id_aarch32(struct kvm_vcpu *vcpu,
 	 * No support for AArch32 guests, therefore, pKVM has no sanitized copy
 	 * of AArch32 feature id registers.
 	 */
-	BUILD_BUG_ON(FIELD_GET(ARM64_FEATURE_MASK(ID_AA64PFR0_EL1),
-		     PVM_ID_AA64PFR0_RESTRICT_UNSIGNED) > ID_AA64PFR0_ELx_64BIT_ONLY);
+	BUILD_BUG_ON(FIELD_GET(ARM64_FEATURE_MASK(ID_AA64PFR0_EL1_EL1),
+		     PVM_ID_AA64PFR0_RESTRICT_UNSIGNED) > ID_AA64PFR0_EL1_ELx_64BIT_ONLY);
 
 	return pvm_access_raz_wi(vcpu, p, r);
 }
@@ -321,6 +324,16 @@ static bool pvm_gic_read_sre(struct kvm_vcpu *vcpu,
 /* Mark the specified system register as an AArch64 feature id register. */
 #define AARCH64(REG) { SYS_DESC(REG), .access = pvm_access_id_aarch64 }
 
+/*
+ * sys_reg_desc initialiser for architecturally unallocated cpufeature ID
+ * register with encoding Op0=3, Op1=0, CRn=0, CRm=crm, Op2=op2
+ * (1 <= crm < 8, 0 <= Op2 < 8).
+ */
+#define ID_UNALLOCATED(crm, op2) {			\
+	Op0(3), Op1(0), CRn(0), CRm(crm), Op2(op2),	\
+	.access = pvm_access_id_aarch64,		\
+}
+
 /* Mark the specified system register as Read-As-Zero/Write-Ignored */
 #define RAZ_WI(REG) { SYS_DESC(REG), .access = pvm_access_raz_wi }
 
@@ -364,24 +377,46 @@ static const struct sys_reg_desc pvm_sys_reg_descs[] = {
 	AARCH32(SYS_MVFR0_EL1),
 	AARCH32(SYS_MVFR1_EL1),
 	AARCH32(SYS_MVFR2_EL1),
+	ID_UNALLOCATED(3,3),
 	AARCH32(SYS_ID_PFR2_EL1),
 	AARCH32(SYS_ID_DFR1_EL1),
 	AARCH32(SYS_ID_MMFR5_EL1),
+	ID_UNALLOCATED(3,7),
 
 	/* AArch64 ID registers */
 	/* CRm=4 */
 	AARCH64(SYS_ID_AA64PFR0_EL1),
 	AARCH64(SYS_ID_AA64PFR1_EL1),
+	ID_UNALLOCATED(4,2),
+	ID_UNALLOCATED(4,3),
 	AARCH64(SYS_ID_AA64ZFR0_EL1),
+	ID_UNALLOCATED(4,5),
+	ID_UNALLOCATED(4,6),
+	ID_UNALLOCATED(4,7),
 	AARCH64(SYS_ID_AA64DFR0_EL1),
 	AARCH64(SYS_ID_AA64DFR1_EL1),
+	ID_UNALLOCATED(5,2),
+	ID_UNALLOCATED(5,3),
 	AARCH64(SYS_ID_AA64AFR0_EL1),
 	AARCH64(SYS_ID_AA64AFR1_EL1),
+	ID_UNALLOCATED(5,6),
+	ID_UNALLOCATED(5,7),
 	AARCH64(SYS_ID_AA64ISAR0_EL1),
 	AARCH64(SYS_ID_AA64ISAR1_EL1),
+	AARCH64(SYS_ID_AA64ISAR2_EL1),
+	ID_UNALLOCATED(6,3),
+	ID_UNALLOCATED(6,4),
+	ID_UNALLOCATED(6,5),
+	ID_UNALLOCATED(6,6),
+	ID_UNALLOCATED(6,7),
 	AARCH64(SYS_ID_AA64MMFR0_EL1),
 	AARCH64(SYS_ID_AA64MMFR1_EL1),
 	AARCH64(SYS_ID_AA64MMFR2_EL1),
+	ID_UNALLOCATED(7,3),
+	ID_UNALLOCATED(7,4),
+	ID_UNALLOCATED(7,5),
+	ID_UNALLOCATED(7,6),
+	ID_UNALLOCATED(7,7),
 
 	/* Scalable Vector Registers are restricted. */
 
diff --git a/arch/arm64/kvm/hyp/pgtable.c b/arch/arm64/kvm/hyp/pgtable.c
index f8ceebe4982e..cdf8e76b0be1 100644
--- a/arch/arm64/kvm/hyp/pgtable.c
+++ b/arch/arm64/kvm/hyp/pgtable.c
@@ -61,7 +61,7 @@ struct kvm_pgtable_walk_data {
 
 static bool kvm_phys_is_valid(u64 phys)
 {
-	return phys < BIT(id_aa64mmfr0_parange_to_phys_shift(ID_AA64MMFR0_PARANGE_MAX));
+	return phys < BIT(id_aa64mmfr0_parange_to_phys_shift(ID_AA64MMFR0_EL1_PARANGE_MAX));
 }
 
 static bool kvm_block_mapping_supported(u64 addr, u64 end, u64 phys, u32 level)
@@ -383,21 +383,6 @@ enum kvm_pgtable_prot kvm_pgtable_hyp_pte_prot(kvm_pte_t pte)
 	return prot;
 }
 
-static bool hyp_pte_needs_update(kvm_pte_t old, kvm_pte_t new)
-{
-	/*
-	 * Tolerate KVM recreating the exact same mapping, or changing software
-	 * bits if the existing mapping was valid.
-	 */
-	if (old == new)
-		return false;
-
-	if (!kvm_pte_valid(old))
-		return true;
-
-	return !WARN_ON((old ^ new) & ~KVM_PTE_LEAF_ATTR_HI_SW);
-}
-
 static bool hyp_map_walker_try_leaf(u64 addr, u64 end, u32 level,
 				    kvm_pte_t *ptep, struct hyp_map_data *data)
 {
@@ -407,11 +392,16 @@ static bool hyp_map_walker_try_leaf(u64 addr, u64 end, u32 level,
 	if (!kvm_block_mapping_supported(addr, end, phys, level))
 		return false;
 
+	data->phys += granule;
 	new = kvm_init_valid_leaf_pte(phys, data->attr, level);
-	if (hyp_pte_needs_update(old, new))
-		smp_store_release(ptep, new);
+	if (old == new)
+		return true;
+	if (!kvm_pte_valid(old))
+		data->mm_ops->get_page(ptep);
+	else if (WARN_ON((old ^ new) & ~KVM_PTE_LEAF_ATTR_HI_SW))
+		return false;
 
-	data->phys += granule;
+	smp_store_release(ptep, new);
 	return true;
 }
 
@@ -433,6 +423,7 @@ static int hyp_map_walker(u64 addr, u64 end, u32 level, kvm_pte_t *ptep,
 		return -ENOMEM;
 
 	kvm_set_table_pte(ptep, childp, mm_ops);
+	mm_ops->get_page(ptep);
 	return 0;
 }
 
@@ -460,6 +451,69 @@ int kvm_pgtable_hyp_map(struct kvm_pgtable *pgt, u64 addr, u64 size, u64 phys,
 	return ret;
 }
 
+struct hyp_unmap_data {
+	u64				unmapped;
+	struct kvm_pgtable_mm_ops	*mm_ops;
+};
+
+static int hyp_unmap_walker(u64 addr, u64 end, u32 level, kvm_pte_t *ptep,
+			    enum kvm_pgtable_walk_flags flag, void * const arg)
+{
+	kvm_pte_t pte = *ptep, *childp = NULL;
+	u64 granule = kvm_granule_size(level);
+	struct hyp_unmap_data *data = arg;
+	struct kvm_pgtable_mm_ops *mm_ops = data->mm_ops;
+
+	if (!kvm_pte_valid(pte))
+		return -EINVAL;
+
+	if (kvm_pte_table(pte, level)) {
+		childp = kvm_pte_follow(pte, mm_ops);
+
+		if (mm_ops->page_count(childp) != 1)
+			return 0;
+
+		kvm_clear_pte(ptep);
+		dsb(ishst);
+		__tlbi_level(vae2is, __TLBI_VADDR(addr, 0), level);
+	} else {
+		if (end - addr < granule)
+			return -EINVAL;
+
+		kvm_clear_pte(ptep);
+		dsb(ishst);
+		__tlbi_level(vale2is, __TLBI_VADDR(addr, 0), level);
+		data->unmapped += granule;
+	}
+
+	dsb(ish);
+	isb();
+	mm_ops->put_page(ptep);
+
+	if (childp)
+		mm_ops->put_page(childp);
+
+	return 0;
+}
+
+u64 kvm_pgtable_hyp_unmap(struct kvm_pgtable *pgt, u64 addr, u64 size)
+{
+	struct hyp_unmap_data unmap_data = {
+		.mm_ops	= pgt->mm_ops,
+	};
+	struct kvm_pgtable_walker walker = {
+		.cb	= hyp_unmap_walker,
+		.arg	= &unmap_data,
+		.flags	= KVM_PGTABLE_WALK_LEAF | KVM_PGTABLE_WALK_TABLE_POST,
+	};
+
+	if (!pgt->mm_ops->page_count)
+		return 0;
+
+	kvm_pgtable_walk(pgt, addr, size, &walker);
+	return unmap_data.unmapped;
+}
+
 int kvm_pgtable_hyp_init(struct kvm_pgtable *pgt, u32 va_bits,
 			 struct kvm_pgtable_mm_ops *mm_ops)
 {
@@ -482,8 +536,16 @@ static int hyp_free_walker(u64 addr, u64 end, u32 level, kvm_pte_t *ptep,
 			   enum kvm_pgtable_walk_flags flag, void * const arg)
 {
 	struct kvm_pgtable_mm_ops *mm_ops = arg;
+	kvm_pte_t pte = *ptep;
+
+	if (!kvm_pte_valid(pte))
+		return 0;
+
+	mm_ops->put_page(ptep);
+
+	if (kvm_pte_table(pte, level))
+		mm_ops->put_page(kvm_pte_follow(pte, mm_ops));
 
-	mm_ops->put_page((void *)kvm_pte_follow(*ptep, mm_ops));
 	return 0;
 }
 
@@ -491,7 +553,7 @@ void kvm_pgtable_hyp_destroy(struct kvm_pgtable *pgt)
 {
 	struct kvm_pgtable_walker walker = {
 		.cb	= hyp_free_walker,
-		.flags	= KVM_PGTABLE_WALK_TABLE_POST,
+		.flags	= KVM_PGTABLE_WALK_LEAF | KVM_PGTABLE_WALK_TABLE_POST,
 		.arg	= pgt->mm_ops,
 	};
 
@@ -921,13 +983,9 @@ static int stage2_unmap_walker(u64 addr, u64 end, u32 level, kvm_pte_t *ptep,
 	 */
 	stage2_put_pte(ptep, mmu, addr, level, mm_ops);
 
-	if (need_flush) {
-		kvm_pte_t *pte_follow = kvm_pte_follow(pte, mm_ops);
-
-		dcache_clean_inval_poc((unsigned long)pte_follow,
-				    (unsigned long)pte_follow +
-					    kvm_granule_size(level));
-	}
+	if (need_flush && mm_ops->dcache_clean_inval_poc)
+		mm_ops->dcache_clean_inval_poc(kvm_pte_follow(pte, mm_ops),
+					       kvm_granule_size(level));
 
 	if (childp)
 		mm_ops->put_page(childp);
@@ -1089,15 +1147,13 @@ static int stage2_flush_walker(u64 addr, u64 end, u32 level, kvm_pte_t *ptep,
 	struct kvm_pgtable *pgt = arg;
 	struct kvm_pgtable_mm_ops *mm_ops = pgt->mm_ops;
 	kvm_pte_t pte = *ptep;
-	kvm_pte_t *pte_follow;
 
 	if (!kvm_pte_valid(pte) || !stage2_pte_cacheable(pgt, pte))
 		return 0;
 
-	pte_follow = kvm_pte_follow(pte, mm_ops);
-	dcache_clean_inval_poc((unsigned long)pte_follow,
-			    (unsigned long)pte_follow +
-				    kvm_granule_size(level));
+	if (mm_ops->dcache_clean_inval_poc)
+		mm_ops->dcache_clean_inval_poc(kvm_pte_follow(pte, mm_ops),
+					       kvm_granule_size(level));
 	return 0;
 }
 
@@ -1116,13 +1172,13 @@ int kvm_pgtable_stage2_flush(struct kvm_pgtable *pgt, u64 addr, u64 size)
 }
 
 
-int __kvm_pgtable_stage2_init(struct kvm_pgtable *pgt, struct kvm_arch *arch,
+int __kvm_pgtable_stage2_init(struct kvm_pgtable *pgt, struct kvm_s2_mmu *mmu,
 			      struct kvm_pgtable_mm_ops *mm_ops,
 			      enum kvm_pgtable_stage2_flags flags,
 			      kvm_pgtable_force_pte_cb_t force_pte_cb)
 {
 	size_t pgd_sz;
-	u64 vtcr = arch->vtcr;
+	u64 vtcr = mmu->arch->vtcr;
 	u32 ia_bits = VTCR_EL2_IPA(vtcr);
 	u32 sl0 = FIELD_GET(VTCR_EL2_SL0_MASK, vtcr);
 	u32 start_level = VTCR_EL2_TGRAN_SL0_BASE - sl0;
@@ -1135,7 +1191,7 @@ int __kvm_pgtable_stage2_init(struct kvm_pgtable *pgt, struct kvm_arch *arch,
 	pgt->ia_bits		= ia_bits;
 	pgt->start_level	= start_level;
 	pgt->mm_ops		= mm_ops;
-	pgt->mmu		= &arch->mmu;
+	pgt->mmu		= mmu;
 	pgt->flags		= flags;
 	pgt->force_pte_cb	= force_pte_cb;
 
diff --git a/arch/arm64/kvm/hyp/reserved_mem.c b/arch/arm64/kvm/hyp/reserved_mem.c
deleted file mode 100644
index 578670e3f608..000000000000
--- a/arch/arm64/kvm/hyp/reserved_mem.c
+++ /dev/null
@@ -1,109 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Copyright (C) 2020 - Google LLC
- * Author: Quentin Perret <qperret@google.com>
- */
-
-#include <linux/kvm_host.h>
-#include <linux/memblock.h>
-#include <linux/sort.h>
-
-#include <asm/kvm_host.h>
-
-#include <nvhe/memory.h>
-#include <nvhe/mm.h>
-
-static struct memblock_region *hyp_memory = kvm_nvhe_sym(hyp_memory);
-static unsigned int *hyp_memblock_nr_ptr = &kvm_nvhe_sym(hyp_memblock_nr);
-
-phys_addr_t hyp_mem_base;
-phys_addr_t hyp_mem_size;
-
-static int cmp_hyp_memblock(const void *p1, const void *p2)
-{
-	const struct memblock_region *r1 = p1;
-	const struct memblock_region *r2 = p2;
-
-	return r1->base < r2->base ? -1 : (r1->base > r2->base);
-}
-
-static void __init sort_memblock_regions(void)
-{
-	sort(hyp_memory,
-	     *hyp_memblock_nr_ptr,
-	     sizeof(struct memblock_region),
-	     cmp_hyp_memblock,
-	     NULL);
-}
-
-static int __init register_memblock_regions(void)
-{
-	struct memblock_region *reg;
-
-	for_each_mem_region(reg) {
-		if (*hyp_memblock_nr_ptr >= HYP_MEMBLOCK_REGIONS)
-			return -ENOMEM;
-
-		hyp_memory[*hyp_memblock_nr_ptr] = *reg;
-		(*hyp_memblock_nr_ptr)++;
-	}
-	sort_memblock_regions();
-
-	return 0;
-}
-
-void __init kvm_hyp_reserve(void)
-{
-	u64 nr_pages, prev, hyp_mem_pages = 0;
-	int ret;
-
-	if (!is_hyp_mode_available() || is_kernel_in_hyp_mode())
-		return;
-
-	if (kvm_get_mode() != KVM_MODE_PROTECTED)
-		return;
-
-	ret = register_memblock_regions();
-	if (ret) {
-		*hyp_memblock_nr_ptr = 0;
-		kvm_err("Failed to register hyp memblocks: %d\n", ret);
-		return;
-	}
-
-	hyp_mem_pages += hyp_s1_pgtable_pages();
-	hyp_mem_pages += host_s2_pgtable_pages();
-
-	/*
-	 * The hyp_vmemmap needs to be backed by pages, but these pages
-	 * themselves need to be present in the vmemmap, so compute the number
-	 * of pages needed by looking for a fixed point.
-	 */
-	nr_pages = 0;
-	do {
-		prev = nr_pages;
-		nr_pages = hyp_mem_pages + prev;
-		nr_pages = DIV_ROUND_UP(nr_pages * sizeof(struct hyp_page), PAGE_SIZE);
-		nr_pages += __hyp_pgtable_max_pages(nr_pages);
-	} while (nr_pages != prev);
-	hyp_mem_pages += nr_pages;
-
-	/*
-	 * Try to allocate a PMD-aligned region to reduce TLB pressure once
-	 * this is unmapped from the host stage-2, and fallback to PAGE_SIZE.
-	 */
-	hyp_mem_size = hyp_mem_pages << PAGE_SHIFT;
-	hyp_mem_base = memblock_phys_alloc(ALIGN(hyp_mem_size, PMD_SIZE),
-					   PMD_SIZE);
-	if (!hyp_mem_base)
-		hyp_mem_base = memblock_phys_alloc(hyp_mem_size, PAGE_SIZE);
-	else
-		hyp_mem_size = ALIGN(hyp_mem_size, PMD_SIZE);
-
-	if (!hyp_mem_base) {
-		kvm_err("Failed to reserve hyp memory\n");
-		return;
-	}
-
-	kvm_info("Reserved %lld MiB at 0x%llx\n", hyp_mem_size >> 20,
-		 hyp_mem_base);
-}
diff --git a/arch/arm64/kvm/hyp/vgic-v3-sr.c b/arch/arm64/kvm/hyp/vgic-v3-sr.c
index 20db2f281cf2..6cb638b184b1 100644
--- a/arch/arm64/kvm/hyp/vgic-v3-sr.c
+++ b/arch/arm64/kvm/hyp/vgic-v3-sr.c
@@ -473,7 +473,7 @@ static int __vgic_v3_bpr_min(void)
 
 static int __vgic_v3_get_group(struct kvm_vcpu *vcpu)
 {
-	u32 esr = kvm_vcpu_get_esr(vcpu);
+	u64 esr = kvm_vcpu_get_esr(vcpu);
 	u8 crm = (esr & ESR_ELx_SYS64_ISS_CRM_MASK) >> ESR_ELx_SYS64_ISS_CRM_SHIFT;
 
 	return crm != 8;
@@ -983,6 +983,9 @@ static void __vgic_v3_read_ctlr(struct kvm_vcpu *vcpu, u32 vmcr, int rt)
 	val = ((vtr >> 29) & 7) << ICC_CTLR_EL1_PRI_BITS_SHIFT;
 	/* IDbits */
 	val |= ((vtr >> 23) & 7) << ICC_CTLR_EL1_ID_BITS_SHIFT;
+	/* SEIS */
+	if (kvm_vgic_global_state.ich_vtr_el2 & ICH_VTR_SEIS_MASK)
+		val |= BIT(ICC_CTLR_EL1_SEIS_SHIFT);
 	/* A3V */
 	val |= ((vtr >> 21) & 1) << ICC_CTLR_EL1_A3V_SHIFT;
 	/* EOImode */
@@ -1013,7 +1016,7 @@ static void __vgic_v3_write_ctlr(struct kvm_vcpu *vcpu, u32 vmcr, int rt)
 int __vgic_v3_perform_cpuif_access(struct kvm_vcpu *vcpu)
 {
 	int rt;
-	u32 esr;
+	u64 esr;
 	u32 vmcr;
 	void (*fn)(struct kvm_vcpu *, u32, int);
 	bool is_read;
diff --git a/arch/arm64/kvm/hyp/vhe/switch.c b/arch/arm64/kvm/hyp/vhe/switch.c
index fbb26b93c347..1a97391fedd2 100644
--- a/arch/arm64/kvm/hyp/vhe/switch.c
+++ b/arch/arm64/kvm/hyp/vhe/switch.c
@@ -10,6 +10,7 @@
 #include <linux/kvm_host.h>
 #include <linux/types.h>
 #include <linux/jump_label.h>
+#include <linux/percpu.h>
 #include <uapi/linux/psci.h>
 
 #include <kvm/arm_psci.h>
@@ -25,6 +26,7 @@
 #include <asm/debug-monitors.h>
 #include <asm/processor.h>
 #include <asm/thread_info.h>
+#include <asm/vectors.h>
 
 /* VHE specific context */
 DEFINE_PER_CPU(struct kvm_host_data, kvm_host_data);
@@ -39,7 +41,8 @@ static void __activate_traps(struct kvm_vcpu *vcpu)
 
 	val = read_sysreg(cpacr_el1);
 	val |= CPACR_EL1_TTA;
-	val &= ~CPACR_EL1_ZEN;
+	val &= ~(CPACR_EL1_ZEN_EL0EN | CPACR_EL1_ZEN_EL1EN |
+		 CPACR_EL1_SMEN_EL0EN | CPACR_EL1_SMEN_EL1EN);
 
 	/*
 	 * With VHE (HCR.E2H == 1), accesses to CPACR_EL1 are routed to
@@ -52,11 +55,11 @@ static void __activate_traps(struct kvm_vcpu *vcpu)
 
 	val |= CPTR_EL2_TAM;
 
-	if (update_fp_enabled(vcpu)) {
+	if (guest_owns_fp_regs(vcpu)) {
 		if (vcpu_has_sve(vcpu))
-			val |= CPACR_EL1_ZEN;
+			val |= CPACR_EL1_ZEN_EL0EN | CPACR_EL1_ZEN_EL1EN;
 	} else {
-		val &= ~CPACR_EL1_FPEN;
+		val &= ~(CPACR_EL1_FPEN_EL0EN | CPACR_EL1_FPEN_EL1EN);
 		__activate_traps_fpsimd32(vcpu);
 	}
 
@@ -68,7 +71,7 @@ NOKPROBE_SYMBOL(__activate_traps);
 
 static void __deactivate_traps(struct kvm_vcpu *vcpu)
 {
-	extern char vectors[];	/* kernel exception vectors */
+	const char *host_vectors = vectors;
 
 	___deactivate_traps(vcpu);
 
@@ -82,7 +85,10 @@ static void __deactivate_traps(struct kvm_vcpu *vcpu)
 	asm(ALTERNATIVE("nop", "isb", ARM64_WORKAROUND_SPECULATIVE_AT));
 
 	write_sysreg(CPACR_EL1_DEFAULT, cpacr_el1);
-	write_sysreg(vectors, vbar_el1);
+
+	if (!arm64_kernel_unmapped_at_el0())
+		host_vectors = __this_cpu_read(this_cpu_vector);
+	write_sysreg(host_vectors, vbar_el1);
 }
 NOKPROBE_SYMBOL(__deactivate_traps);
 
@@ -161,7 +167,7 @@ static int __kvm_vcpu_run_vhe(struct kvm_vcpu *vcpu)
 
 	sysreg_restore_host_state_vhe(host_ctxt);
 
-	if (vcpu->arch.flags & KVM_ARM64_FP_ENABLED)
+	if (vcpu->arch.fp_state == FP_STATE_GUEST_OWNED)
 		__fpsimd_save_fpexc32(vcpu);
 
 	__debug_switch_to_host(vcpu);
@@ -235,5 +241,5 @@ void __noreturn hyp_panic(void)
 
 asmlinkage void kvm_unexpected_el2_exception(void)
 {
-	return __kvm_unexpected_el2_exception();
+	__kvm_unexpected_el2_exception();
 }
diff --git a/arch/arm64/kvm/hyp/vhe/sysreg-sr.c b/arch/arm64/kvm/hyp/vhe/sysreg-sr.c
index 007a12dd4351..7b44f6b3b547 100644
--- a/arch/arm64/kvm/hyp/vhe/sysreg-sr.c
+++ b/arch/arm64/kvm/hyp/vhe/sysreg-sr.c
@@ -79,7 +79,7 @@ void kvm_vcpu_load_sysregs_vhe(struct kvm_vcpu *vcpu)
 	__sysreg_restore_user_state(guest_ctxt);
 	__sysreg_restore_el1_state(guest_ctxt);
 
-	vcpu->arch.sysregs_loaded_on_cpu = true;
+	vcpu_set_flag(vcpu, SYSREGS_ON_CPU);
 
 	activate_traps_vhe_load(vcpu);
 }
@@ -110,5 +110,5 @@ void kvm_vcpu_put_sysregs_vhe(struct kvm_vcpu *vcpu)
 	/* Restore host user state */
 	__sysreg_restore_user_state(host_ctxt);
 
-	vcpu->arch.sysregs_loaded_on_cpu = false;
+	vcpu_clear_flag(vcpu, SYSREGS_ON_CPU);
 }
diff --git a/arch/arm64/kvm/hypercalls.c b/arch/arm64/kvm/hypercalls.c
index 30da78f72b3b..c9f401fa01a9 100644
--- a/arch/arm64/kvm/hypercalls.c
+++ b/arch/arm64/kvm/hypercalls.c
@@ -9,6 +9,13 @@
 #include <kvm/arm_hypercalls.h>
 #include <kvm/arm_psci.h>
 
+#define KVM_ARM_SMCCC_STD_FEATURES				\
+	GENMASK(KVM_REG_ARM_STD_BMAP_BIT_COUNT - 1, 0)
+#define KVM_ARM_SMCCC_STD_HYP_FEATURES				\
+	GENMASK(KVM_REG_ARM_STD_HYP_BMAP_BIT_COUNT - 1, 0)
+#define KVM_ARM_SMCCC_VENDOR_HYP_FEATURES			\
+	GENMASK(KVM_REG_ARM_VENDOR_HYP_BMAP_BIT_COUNT - 1, 0)
+
 static void kvm_ptp_get_time(struct kvm_vcpu *vcpu, u64 *val)
 {
 	struct system_time_snapshot systime_snapshot;
@@ -58,13 +65,73 @@ static void kvm_ptp_get_time(struct kvm_vcpu *vcpu, u64 *val)
 	val[3] = lower_32_bits(cycles);
 }
 
+static bool kvm_hvc_call_default_allowed(u32 func_id)
+{
+	switch (func_id) {
+	/*
+	 * List of function-ids that are not gated with the bitmapped
+	 * feature firmware registers, and are to be allowed for
+	 * servicing the call by default.
+	 */
+	case ARM_SMCCC_VERSION_FUNC_ID:
+	case ARM_SMCCC_ARCH_FEATURES_FUNC_ID:
+		return true;
+	default:
+		/* PSCI 0.2 and up is in the 0:0x1f range */
+		if (ARM_SMCCC_OWNER_NUM(func_id) == ARM_SMCCC_OWNER_STANDARD &&
+		    ARM_SMCCC_FUNC_NUM(func_id) <= 0x1f)
+			return true;
+
+		/*
+		 * KVM's PSCI 0.1 doesn't comply with SMCCC, and has
+		 * its own function-id base and range
+		 */
+		if (func_id >= KVM_PSCI_FN(0) && func_id <= KVM_PSCI_FN(3))
+			return true;
+
+		return false;
+	}
+}
+
+static bool kvm_hvc_call_allowed(struct kvm_vcpu *vcpu, u32 func_id)
+{
+	struct kvm_smccc_features *smccc_feat = &vcpu->kvm->arch.smccc_feat;
+
+	switch (func_id) {
+	case ARM_SMCCC_TRNG_VERSION:
+	case ARM_SMCCC_TRNG_FEATURES:
+	case ARM_SMCCC_TRNG_GET_UUID:
+	case ARM_SMCCC_TRNG_RND32:
+	case ARM_SMCCC_TRNG_RND64:
+		return test_bit(KVM_REG_ARM_STD_BIT_TRNG_V1_0,
+				&smccc_feat->std_bmap);
+	case ARM_SMCCC_HV_PV_TIME_FEATURES:
+	case ARM_SMCCC_HV_PV_TIME_ST:
+		return test_bit(KVM_REG_ARM_STD_HYP_BIT_PV_TIME,
+				&smccc_feat->std_hyp_bmap);
+	case ARM_SMCCC_VENDOR_HYP_KVM_FEATURES_FUNC_ID:
+	case ARM_SMCCC_VENDOR_HYP_CALL_UID_FUNC_ID:
+		return test_bit(KVM_REG_ARM_VENDOR_HYP_BIT_FUNC_FEAT,
+				&smccc_feat->vendor_hyp_bmap);
+	case ARM_SMCCC_VENDOR_HYP_KVM_PTP_FUNC_ID:
+		return test_bit(KVM_REG_ARM_VENDOR_HYP_BIT_PTP,
+				&smccc_feat->vendor_hyp_bmap);
+	default:
+		return kvm_hvc_call_default_allowed(func_id);
+	}
+}
+
 int kvm_hvc_call_handler(struct kvm_vcpu *vcpu)
 {
+	struct kvm_smccc_features *smccc_feat = &vcpu->kvm->arch.smccc_feat;
 	u32 func_id = smccc_get_function(vcpu);
 	u64 val[4] = {SMCCC_RET_NOT_SUPPORTED};
 	u32 feature;
 	gpa_t gpa;
 
+	if (!kvm_hvc_call_allowed(vcpu, func_id))
+		goto out;
+
 	switch (func_id) {
 	case ARM_SMCCC_VERSION_FUNC_ID:
 		val[0] = ARM_SMCCC_VERSION_1_1;
@@ -107,8 +174,22 @@ int kvm_hvc_call_handler(struct kvm_vcpu *vcpu)
 				break;
 			}
 			break;
+		case ARM_SMCCC_ARCH_WORKAROUND_3:
+			switch (arm64_get_spectre_bhb_state()) {
+			case SPECTRE_VULNERABLE:
+				break;
+			case SPECTRE_MITIGATED:
+				val[0] = SMCCC_RET_SUCCESS;
+				break;
+			case SPECTRE_UNAFFECTED:
+				val[0] = SMCCC_ARCH_WORKAROUND_RET_UNAFFECTED;
+				break;
+			}
+			break;
 		case ARM_SMCCC_HV_PV_TIME_FEATURES:
-			val[0] = SMCCC_RET_SUCCESS;
+			if (test_bit(KVM_REG_ARM_STD_HYP_BIT_PV_TIME,
+				     &smccc_feat->std_hyp_bmap))
+				val[0] = SMCCC_RET_SUCCESS;
 			break;
 		}
 		break;
@@ -127,8 +208,7 @@ int kvm_hvc_call_handler(struct kvm_vcpu *vcpu)
 		val[3] = ARM_SMCCC_VENDOR_HYP_UID_KVM_REG_3;
 		break;
 	case ARM_SMCCC_VENDOR_HYP_KVM_FEATURES_FUNC_ID:
-		val[0] = BIT(ARM_SMCCC_KVM_FUNC_FEATURES);
-		val[0] |= BIT(ARM_SMCCC_KVM_FUNC_PTP);
+		val[0] = smccc_feat->vendor_hyp_bmap;
 		break;
 	case ARM_SMCCC_VENDOR_HYP_KVM_PTP_FUNC_ID:
 		kvm_ptp_get_time(vcpu, val);
@@ -143,6 +223,259 @@ int kvm_hvc_call_handler(struct kvm_vcpu *vcpu)
 		return kvm_psci_call(vcpu);
 	}
 
+out:
 	smccc_set_retval(vcpu, val[0], val[1], val[2], val[3]);
 	return 1;
 }
+
+static const u64 kvm_arm_fw_reg_ids[] = {
+	KVM_REG_ARM_PSCI_VERSION,
+	KVM_REG_ARM_SMCCC_ARCH_WORKAROUND_1,
+	KVM_REG_ARM_SMCCC_ARCH_WORKAROUND_2,
+	KVM_REG_ARM_SMCCC_ARCH_WORKAROUND_3,
+	KVM_REG_ARM_STD_BMAP,
+	KVM_REG_ARM_STD_HYP_BMAP,
+	KVM_REG_ARM_VENDOR_HYP_BMAP,
+};
+
+void kvm_arm_init_hypercalls(struct kvm *kvm)
+{
+	struct kvm_smccc_features *smccc_feat = &kvm->arch.smccc_feat;
+
+	smccc_feat->std_bmap = KVM_ARM_SMCCC_STD_FEATURES;
+	smccc_feat->std_hyp_bmap = KVM_ARM_SMCCC_STD_HYP_FEATURES;
+	smccc_feat->vendor_hyp_bmap = KVM_ARM_SMCCC_VENDOR_HYP_FEATURES;
+}
+
+int kvm_arm_get_fw_num_regs(struct kvm_vcpu *vcpu)
+{
+	return ARRAY_SIZE(kvm_arm_fw_reg_ids);
+}
+
+int kvm_arm_copy_fw_reg_indices(struct kvm_vcpu *vcpu, u64 __user *uindices)
+{
+	int i;
+
+	for (i = 0; i < ARRAY_SIZE(kvm_arm_fw_reg_ids); i++) {
+		if (put_user(kvm_arm_fw_reg_ids[i], uindices++))
+			return -EFAULT;
+	}
+
+	return 0;
+}
+
+#define KVM_REG_FEATURE_LEVEL_MASK	GENMASK(3, 0)
+
+/*
+ * Convert the workaround level into an easy-to-compare number, where higher
+ * values mean better protection.
+ */
+static int get_kernel_wa_level(u64 regid)
+{
+	switch (regid) {
+	case KVM_REG_ARM_SMCCC_ARCH_WORKAROUND_1:
+		switch (arm64_get_spectre_v2_state()) {
+		case SPECTRE_VULNERABLE:
+			return KVM_REG_ARM_SMCCC_ARCH_WORKAROUND_1_NOT_AVAIL;
+		case SPECTRE_MITIGATED:
+			return KVM_REG_ARM_SMCCC_ARCH_WORKAROUND_1_AVAIL;
+		case SPECTRE_UNAFFECTED:
+			return KVM_REG_ARM_SMCCC_ARCH_WORKAROUND_1_NOT_REQUIRED;
+		}
+		return KVM_REG_ARM_SMCCC_ARCH_WORKAROUND_1_NOT_AVAIL;
+	case KVM_REG_ARM_SMCCC_ARCH_WORKAROUND_2:
+		switch (arm64_get_spectre_v4_state()) {
+		case SPECTRE_MITIGATED:
+			/*
+			 * As for the hypercall discovery, we pretend we
+			 * don't have any FW mitigation if SSBS is there at
+			 * all times.
+			 */
+			if (cpus_have_final_cap(ARM64_SSBS))
+				return KVM_REG_ARM_SMCCC_ARCH_WORKAROUND_2_NOT_AVAIL;
+			fallthrough;
+		case SPECTRE_UNAFFECTED:
+			return KVM_REG_ARM_SMCCC_ARCH_WORKAROUND_2_NOT_REQUIRED;
+		case SPECTRE_VULNERABLE:
+			return KVM_REG_ARM_SMCCC_ARCH_WORKAROUND_2_NOT_AVAIL;
+		}
+		break;
+	case KVM_REG_ARM_SMCCC_ARCH_WORKAROUND_3:
+		switch (arm64_get_spectre_bhb_state()) {
+		case SPECTRE_VULNERABLE:
+			return KVM_REG_ARM_SMCCC_ARCH_WORKAROUND_3_NOT_AVAIL;
+		case SPECTRE_MITIGATED:
+			return KVM_REG_ARM_SMCCC_ARCH_WORKAROUND_3_AVAIL;
+		case SPECTRE_UNAFFECTED:
+			return KVM_REG_ARM_SMCCC_ARCH_WORKAROUND_3_NOT_REQUIRED;
+		}
+		return KVM_REG_ARM_SMCCC_ARCH_WORKAROUND_3_NOT_AVAIL;
+	}
+
+	return -EINVAL;
+}
+
+int kvm_arm_get_fw_reg(struct kvm_vcpu *vcpu, const struct kvm_one_reg *reg)
+{
+	struct kvm_smccc_features *smccc_feat = &vcpu->kvm->arch.smccc_feat;
+	void __user *uaddr = (void __user *)(long)reg->addr;
+	u64 val;
+
+	switch (reg->id) {
+	case KVM_REG_ARM_PSCI_VERSION:
+		val = kvm_psci_version(vcpu);
+		break;
+	case KVM_REG_ARM_SMCCC_ARCH_WORKAROUND_1:
+	case KVM_REG_ARM_SMCCC_ARCH_WORKAROUND_2:
+	case KVM_REG_ARM_SMCCC_ARCH_WORKAROUND_3:
+		val = get_kernel_wa_level(reg->id) & KVM_REG_FEATURE_LEVEL_MASK;
+		break;
+	case KVM_REG_ARM_STD_BMAP:
+		val = READ_ONCE(smccc_feat->std_bmap);
+		break;
+	case KVM_REG_ARM_STD_HYP_BMAP:
+		val = READ_ONCE(smccc_feat->std_hyp_bmap);
+		break;
+	case KVM_REG_ARM_VENDOR_HYP_BMAP:
+		val = READ_ONCE(smccc_feat->vendor_hyp_bmap);
+		break;
+	default:
+		return -ENOENT;
+	}
+
+	if (copy_to_user(uaddr, &val, KVM_REG_SIZE(reg->id)))
+		return -EFAULT;
+
+	return 0;
+}
+
+static int kvm_arm_set_fw_reg_bmap(struct kvm_vcpu *vcpu, u64 reg_id, u64 val)
+{
+	int ret = 0;
+	struct kvm *kvm = vcpu->kvm;
+	struct kvm_smccc_features *smccc_feat = &kvm->arch.smccc_feat;
+	unsigned long *fw_reg_bmap, fw_reg_features;
+
+	switch (reg_id) {
+	case KVM_REG_ARM_STD_BMAP:
+		fw_reg_bmap = &smccc_feat->std_bmap;
+		fw_reg_features = KVM_ARM_SMCCC_STD_FEATURES;
+		break;
+	case KVM_REG_ARM_STD_HYP_BMAP:
+		fw_reg_bmap = &smccc_feat->std_hyp_bmap;
+		fw_reg_features = KVM_ARM_SMCCC_STD_HYP_FEATURES;
+		break;
+	case KVM_REG_ARM_VENDOR_HYP_BMAP:
+		fw_reg_bmap = &smccc_feat->vendor_hyp_bmap;
+		fw_reg_features = KVM_ARM_SMCCC_VENDOR_HYP_FEATURES;
+		break;
+	default:
+		return -ENOENT;
+	}
+
+	/* Check for unsupported bit */
+	if (val & ~fw_reg_features)
+		return -EINVAL;
+
+	mutex_lock(&kvm->lock);
+
+	if (test_bit(KVM_ARCH_FLAG_HAS_RAN_ONCE, &kvm->arch.flags) &&
+	    val != *fw_reg_bmap) {
+		ret = -EBUSY;
+		goto out;
+	}
+
+	WRITE_ONCE(*fw_reg_bmap, val);
+out:
+	mutex_unlock(&kvm->lock);
+	return ret;
+}
+
+int kvm_arm_set_fw_reg(struct kvm_vcpu *vcpu, const struct kvm_one_reg *reg)
+{
+	void __user *uaddr = (void __user *)(long)reg->addr;
+	u64 val;
+	int wa_level;
+
+	if (copy_from_user(&val, uaddr, KVM_REG_SIZE(reg->id)))
+		return -EFAULT;
+
+	switch (reg->id) {
+	case KVM_REG_ARM_PSCI_VERSION:
+	{
+		bool wants_02;
+
+		wants_02 = test_bit(KVM_ARM_VCPU_PSCI_0_2, vcpu->arch.features);
+
+		switch (val) {
+		case KVM_ARM_PSCI_0_1:
+			if (wants_02)
+				return -EINVAL;
+			vcpu->kvm->arch.psci_version = val;
+			return 0;
+		case KVM_ARM_PSCI_0_2:
+		case KVM_ARM_PSCI_1_0:
+		case KVM_ARM_PSCI_1_1:
+			if (!wants_02)
+				return -EINVAL;
+			vcpu->kvm->arch.psci_version = val;
+			return 0;
+		}
+		break;
+	}
+
+	case KVM_REG_ARM_SMCCC_ARCH_WORKAROUND_1:
+	case KVM_REG_ARM_SMCCC_ARCH_WORKAROUND_3:
+		if (val & ~KVM_REG_FEATURE_LEVEL_MASK)
+			return -EINVAL;
+
+		if (get_kernel_wa_level(reg->id) < val)
+			return -EINVAL;
+
+		return 0;
+
+	case KVM_REG_ARM_SMCCC_ARCH_WORKAROUND_2:
+		if (val & ~(KVM_REG_FEATURE_LEVEL_MASK |
+			    KVM_REG_ARM_SMCCC_ARCH_WORKAROUND_2_ENABLED))
+			return -EINVAL;
+
+		/* The enabled bit must not be set unless the level is AVAIL. */
+		if ((val & KVM_REG_ARM_SMCCC_ARCH_WORKAROUND_2_ENABLED) &&
+		    (val & KVM_REG_FEATURE_LEVEL_MASK) != KVM_REG_ARM_SMCCC_ARCH_WORKAROUND_2_AVAIL)
+			return -EINVAL;
+
+		/*
+		 * Map all the possible incoming states to the only two we
+		 * really want to deal with.
+		 */
+		switch (val & KVM_REG_FEATURE_LEVEL_MASK) {
+		case KVM_REG_ARM_SMCCC_ARCH_WORKAROUND_2_NOT_AVAIL:
+		case KVM_REG_ARM_SMCCC_ARCH_WORKAROUND_2_UNKNOWN:
+			wa_level = KVM_REG_ARM_SMCCC_ARCH_WORKAROUND_2_NOT_AVAIL;
+			break;
+		case KVM_REG_ARM_SMCCC_ARCH_WORKAROUND_2_AVAIL:
+		case KVM_REG_ARM_SMCCC_ARCH_WORKAROUND_2_NOT_REQUIRED:
+			wa_level = KVM_REG_ARM_SMCCC_ARCH_WORKAROUND_2_NOT_REQUIRED;
+			break;
+		default:
+			return -EINVAL;
+		}
+
+		/*
+		 * We can deal with NOT_AVAIL on NOT_REQUIRED, but not the
+		 * other way around.
+		 */
+		if (get_kernel_wa_level(reg->id) < wa_level)
+			return -EINVAL;
+
+		return 0;
+	case KVM_REG_ARM_STD_BMAP:
+	case KVM_REG_ARM_STD_HYP_BMAP:
+	case KVM_REG_ARM_VENDOR_HYP_BMAP:
+		return kvm_arm_set_fw_reg_bmap(vcpu, reg->id, val);
+	default:
+		return -ENOENT;
+	}
+
+	return -EINVAL;
+}
diff --git a/arch/arm64/kvm/inject_fault.c b/arch/arm64/kvm/inject_fault.c
index b47df73e98d7..f32f4a2a347f 100644
--- a/arch/arm64/kvm/inject_fault.c
+++ b/arch/arm64/kvm/inject_fault.c
@@ -18,11 +18,9 @@ static void inject_abt64(struct kvm_vcpu *vcpu, bool is_iabt, unsigned long addr
 {
 	unsigned long cpsr = *vcpu_cpsr(vcpu);
 	bool is_aarch32 = vcpu_mode_is_32bit(vcpu);
-	u32 esr = 0;
+	u64 esr = 0;
 
-	vcpu->arch.flags |= (KVM_ARM64_EXCEPT_AA64_EL1		|
-			     KVM_ARM64_EXCEPT_AA64_ELx_SYNC	|
-			     KVM_ARM64_PENDING_EXCEPTION);
+	kvm_pend_exception(vcpu, EXCEPT_AA64_EL1_SYNC);
 
 	vcpu_write_sys_reg(vcpu, addr, FAR_EL1);
 
@@ -50,11 +48,9 @@ static void inject_abt64(struct kvm_vcpu *vcpu, bool is_iabt, unsigned long addr
 
 static void inject_undef64(struct kvm_vcpu *vcpu)
 {
-	u32 esr = (ESR_ELx_EC_UNKNOWN << ESR_ELx_EC_SHIFT);
+	u64 esr = (ESR_ELx_EC_UNKNOWN << ESR_ELx_EC_SHIFT);
 
-	vcpu->arch.flags |= (KVM_ARM64_EXCEPT_AA64_EL1		|
-			     KVM_ARM64_EXCEPT_AA64_ELx_SYNC	|
-			     KVM_ARM64_PENDING_EXCEPTION);
+	kvm_pend_exception(vcpu, EXCEPT_AA64_EL1_SYNC);
 
 	/*
 	 * Build an unknown exception, depending on the instruction
@@ -73,8 +69,7 @@ static void inject_undef64(struct kvm_vcpu *vcpu)
 
 static void inject_undef32(struct kvm_vcpu *vcpu)
 {
-	vcpu->arch.flags |= (KVM_ARM64_EXCEPT_AA32_UND |
-			     KVM_ARM64_PENDING_EXCEPTION);
+	kvm_pend_exception(vcpu, EXCEPT_AA32_UND);
 }
 
 /*
@@ -97,14 +92,12 @@ static void inject_abt32(struct kvm_vcpu *vcpu, bool is_pabt, u32 addr)
 	far = vcpu_read_sys_reg(vcpu, FAR_EL1);
 
 	if (is_pabt) {
-		vcpu->arch.flags |= (KVM_ARM64_EXCEPT_AA32_IABT |
-				     KVM_ARM64_PENDING_EXCEPTION);
+		kvm_pend_exception(vcpu, EXCEPT_AA32_IABT);
 		far &= GENMASK(31, 0);
 		far |= (u64)addr << 32;
 		vcpu_write_sys_reg(vcpu, fsr, IFSR32_EL2);
 	} else { /* !iabt */
-		vcpu->arch.flags |= (KVM_ARM64_EXCEPT_AA32_DABT |
-				     KVM_ARM64_PENDING_EXCEPTION);
+		kvm_pend_exception(vcpu, EXCEPT_AA32_DABT);
 		far &= GENMASK(63, 32);
 		far |= addr;
 		vcpu_write_sys_reg(vcpu, fsr, ESR_EL1);
@@ -145,6 +138,34 @@ void kvm_inject_pabt(struct kvm_vcpu *vcpu, unsigned long addr)
 		inject_abt64(vcpu, true, addr);
 }
 
+void kvm_inject_size_fault(struct kvm_vcpu *vcpu)
+{
+	unsigned long addr, esr;
+
+	addr  = kvm_vcpu_get_fault_ipa(vcpu);
+	addr |= kvm_vcpu_get_hfar(vcpu) & GENMASK(11, 0);
+
+	if (kvm_vcpu_trap_is_iabt(vcpu))
+		kvm_inject_pabt(vcpu, addr);
+	else
+		kvm_inject_dabt(vcpu, addr);
+
+	/*
+	 * If AArch64 or LPAE, set FSC to 0 to indicate an Address
+	 * Size Fault at level 0, as if exceeding PARange.
+	 *
+	 * Non-LPAE guests will only get the external abort, as there
+	 * is no way to to describe the ASF.
+	 */
+	if (vcpu_el1_is_32bit(vcpu) &&
+	    !(vcpu_read_sys_reg(vcpu, TCR_EL1) & TTBCR_EAE))
+		return;
+
+	esr = vcpu_read_sys_reg(vcpu, ESR_EL1);
+	esr &= ~GENMASK_ULL(5, 0);
+	vcpu_write_sys_reg(vcpu, esr, ESR_EL1);
+}
+
 /**
  * kvm_inject_undefined - inject an undefined instruction into the guest
  * @vcpu: The vCPU in which to inject the exception
diff --git a/arch/arm64/kvm/mmio.c b/arch/arm64/kvm/mmio.c
index 3e2d8ba11a02..3dd38a151d2a 100644
--- a/arch/arm64/kvm/mmio.c
+++ b/arch/arm64/kvm/mmio.c
@@ -135,7 +135,8 @@ int io_mem_abort(struct kvm_vcpu *vcpu, phys_addr_t fault_ipa)
 	 * volunteered to do so, and bail out otherwise.
 	 */
 	if (!kvm_vcpu_dabt_isvalid(vcpu)) {
-		if (vcpu->kvm->arch.return_nisv_io_abort_to_user) {
+		if (test_bit(KVM_ARCH_FLAG_RETURN_NISV_IO_ABORT_TO_USER,
+			     &vcpu->kvm->arch.flags)) {
 			run->exit_reason = KVM_EXIT_ARM_NISV;
 			run->arm_nisv.esr_iss = kvm_vcpu_dabt_iss_nisv_sanitized(vcpu);
 			run->arm_nisv.fault_ipa = fault_ipa;
diff --git a/arch/arm64/kvm/mmu.c b/arch/arm64/kvm/mmu.c
index 326cdfec74a1..60ee3d9f01f8 100644
--- a/arch/arm64/kvm/mmu.c
+++ b/arch/arm64/kvm/mmu.c
@@ -31,6 +31,13 @@ static phys_addr_t hyp_idmap_vector;
 
 static unsigned long io_map_base;
 
+static phys_addr_t stage2_range_addr_end(phys_addr_t addr, phys_addr_t end)
+{
+	phys_addr_t size = kvm_granule_size(KVM_PGTABLE_MIN_BLOCK_LEVEL);
+	phys_addr_t boundary = ALIGN_DOWN(addr + size, size);
+
+	return (boundary - 1 < end - 1) ? boundary : end;
+}
 
 /*
  * Release kvm_mmu_lock periodically if the memory region is large. Otherwise,
@@ -52,13 +59,13 @@ static int stage2_apply_range(struct kvm *kvm, phys_addr_t addr,
 		if (!pgt)
 			return -EINVAL;
 
-		next = stage2_pgd_addr_end(kvm, addr, end);
+		next = stage2_range_addr_end(addr, end);
 		ret = fn(pgt, addr, next - addr);
 		if (ret)
 			break;
 
 		if (resched && next != end)
-			cond_resched_lock(&kvm->mmu_lock);
+			cond_resched_rwlock_write(&kvm->mmu_lock);
 	} while (addr = next, addr != end);
 
 	return ret;
@@ -92,9 +99,13 @@ static bool kvm_is_device_pfn(unsigned long pfn)
 static void *stage2_memcache_zalloc_page(void *arg)
 {
 	struct kvm_mmu_memory_cache *mc = arg;
+	void *virt;
 
 	/* Allocated with __GFP_ZERO, so no need to zero */
-	return kvm_mmu_memory_cache_alloc(mc);
+	virt = kvm_mmu_memory_cache_alloc(mc);
+	if (virt)
+		kvm_account_pgtable_pages(virt, 1);
+	return virt;
 }
 
 static void *kvm_host_zalloc_pages_exact(size_t size)
@@ -102,6 +113,21 @@ static void *kvm_host_zalloc_pages_exact(size_t size)
 	return alloc_pages_exact(size, GFP_KERNEL_ACCOUNT | __GFP_ZERO);
 }
 
+static void *kvm_s2_zalloc_pages_exact(size_t size)
+{
+	void *virt = kvm_host_zalloc_pages_exact(size);
+
+	if (virt)
+		kvm_account_pgtable_pages(virt, (size >> PAGE_SHIFT));
+	return virt;
+}
+
+static void kvm_s2_free_pages_exact(void *virt, size_t size)
+{
+	kvm_account_pgtable_pages(virt, -(size >> PAGE_SHIFT));
+	free_pages_exact(virt, size);
+}
+
 static void kvm_host_get_page(void *addr)
 {
 	get_page(virt_to_page(addr));
@@ -112,6 +138,15 @@ static void kvm_host_put_page(void *addr)
 	put_page(virt_to_page(addr));
 }
 
+static void kvm_s2_put_page(void *addr)
+{
+	struct page *p = virt_to_page(addr);
+	/* Dropping last refcount, the page will be freed */
+	if (page_count(p) == 1)
+		kvm_account_pgtable_pages(addr, -1);
+	put_page(p);
+}
+
 static int kvm_host_page_count(void *addr)
 {
 	return page_count(virt_to_page(addr));
@@ -179,7 +214,7 @@ static void __unmap_stage2_range(struct kvm_s2_mmu *mmu, phys_addr_t start, u64
 	struct kvm *kvm = kvm_s2_mmu_to_kvm(mmu);
 	phys_addr_t end = start + size;
 
-	assert_spin_locked(&kvm->mmu_lock);
+	lockdep_assert_held_write(&kvm->mmu_lock);
 	WARN_ON(size & ~PAGE_MASK);
 	WARN_ON(stage2_apply_range(kvm, start, end, kvm_pgtable_stage2_unmap,
 				   may_block));
@@ -210,16 +245,16 @@ static void stage2_flush_vm(struct kvm *kvm)
 {
 	struct kvm_memslots *slots;
 	struct kvm_memory_slot *memslot;
-	int idx;
+	int idx, bkt;
 
 	idx = srcu_read_lock(&kvm->srcu);
-	spin_lock(&kvm->mmu_lock);
+	write_lock(&kvm->mmu_lock);
 
 	slots = kvm_memslots(kvm);
-	kvm_for_each_memslot(memslot, slots)
+	kvm_for_each_memslot(memslot, bkt, slots)
 		stage2_flush_memslot(kvm, memslot);
 
-	spin_unlock(&kvm->mmu_lock);
+	write_unlock(&kvm->mmu_lock);
 	srcu_read_unlock(&kvm->srcu, idx);
 }
 
@@ -239,6 +274,9 @@ void free_hyp_pgds(void)
 
 static bool kvm_host_owns_hyp_mappings(void)
 {
+	if (is_kernel_in_hyp_mode())
+		return false;
+
 	if (static_branch_likely(&kvm_protected_mode_initialized))
 		return false;
 
@@ -255,8 +293,8 @@ static bool kvm_host_owns_hyp_mappings(void)
 	return true;
 }
 
-static int __create_hyp_mappings(unsigned long start, unsigned long size,
-				 unsigned long phys, enum kvm_pgtable_prot prot)
+int __create_hyp_mappings(unsigned long start, unsigned long size,
+			  unsigned long phys, enum kvm_pgtable_prot prot)
 {
 	int err;
 
@@ -281,14 +319,117 @@ static phys_addr_t kvm_kaddr_to_phys(void *kaddr)
 	}
 }
 
-static int pkvm_share_hyp(phys_addr_t start, phys_addr_t end)
+struct hyp_shared_pfn {
+	u64 pfn;
+	int count;
+	struct rb_node node;
+};
+
+static DEFINE_MUTEX(hyp_shared_pfns_lock);
+static struct rb_root hyp_shared_pfns = RB_ROOT;
+
+static struct hyp_shared_pfn *find_shared_pfn(u64 pfn, struct rb_node ***node,
+					      struct rb_node **parent)
 {
-	phys_addr_t addr;
+	struct hyp_shared_pfn *this;
+
+	*node = &hyp_shared_pfns.rb_node;
+	*parent = NULL;
+	while (**node) {
+		this = container_of(**node, struct hyp_shared_pfn, node);
+		*parent = **node;
+		if (this->pfn < pfn)
+			*node = &((**node)->rb_left);
+		else if (this->pfn > pfn)
+			*node = &((**node)->rb_right);
+		else
+			return this;
+	}
+
+	return NULL;
+}
+
+static int share_pfn_hyp(u64 pfn)
+{
+	struct rb_node **node, *parent;
+	struct hyp_shared_pfn *this;
+	int ret = 0;
+
+	mutex_lock(&hyp_shared_pfns_lock);
+	this = find_shared_pfn(pfn, &node, &parent);
+	if (this) {
+		this->count++;
+		goto unlock;
+	}
+
+	this = kzalloc(sizeof(*this), GFP_KERNEL);
+	if (!this) {
+		ret = -ENOMEM;
+		goto unlock;
+	}
+
+	this->pfn = pfn;
+	this->count = 1;
+	rb_link_node(&this->node, parent, node);
+	rb_insert_color(&this->node, &hyp_shared_pfns);
+	ret = kvm_call_hyp_nvhe(__pkvm_host_share_hyp, pfn, 1);
+unlock:
+	mutex_unlock(&hyp_shared_pfns_lock);
+
+	return ret;
+}
+
+static int unshare_pfn_hyp(u64 pfn)
+{
+	struct rb_node **node, *parent;
+	struct hyp_shared_pfn *this;
+	int ret = 0;
+
+	mutex_lock(&hyp_shared_pfns_lock);
+	this = find_shared_pfn(pfn, &node, &parent);
+	if (WARN_ON(!this)) {
+		ret = -ENOENT;
+		goto unlock;
+	}
+
+	this->count--;
+	if (this->count)
+		goto unlock;
+
+	rb_erase(&this->node, &hyp_shared_pfns);
+	kfree(this);
+	ret = kvm_call_hyp_nvhe(__pkvm_host_unshare_hyp, pfn, 1);
+unlock:
+	mutex_unlock(&hyp_shared_pfns_lock);
+
+	return ret;
+}
+
+int kvm_share_hyp(void *from, void *to)
+{
+	phys_addr_t start, end, cur;
+	u64 pfn;
 	int ret;
 
-	for (addr = ALIGN_DOWN(start, PAGE_SIZE); addr < end; addr += PAGE_SIZE) {
-		ret = kvm_call_hyp_nvhe(__pkvm_host_share_hyp,
-					__phys_to_pfn(addr));
+	if (is_kernel_in_hyp_mode())
+		return 0;
+
+	/*
+	 * The share hcall maps things in the 'fixed-offset' region of the hyp
+	 * VA space, so we can only share physically contiguous data-structures
+	 * for now.
+	 */
+	if (is_vmalloc_or_module_addr(from) || is_vmalloc_or_module_addr(to))
+		return -EINVAL;
+
+	if (kvm_host_owns_hyp_mappings())
+		return create_hyp_mappings(from, to, PAGE_HYP);
+
+	start = ALIGN_DOWN(__pa(from), PAGE_SIZE);
+	end = PAGE_ALIGN(__pa(to));
+	for (cur = start; cur < end; cur += PAGE_SIZE) {
+		pfn = __phys_to_pfn(cur);
+		ret = share_pfn_hyp(pfn);
 		if (ret)
 			return ret;
 	}
@@ -296,6 +437,22 @@ static int pkvm_share_hyp(phys_addr_t start, phys_addr_t end)
 	return 0;
 }
 
+void kvm_unshare_hyp(void *from, void *to)
+{
+	phys_addr_t start, end, cur;
+	u64 pfn;
+
+	if (is_kernel_in_hyp_mode() || kvm_host_owns_hyp_mappings() || !from)
+		return;
+
+	start = ALIGN_DOWN(__pa(from), PAGE_SIZE);
+	end = PAGE_ALIGN(__pa(to));
+	for (cur = start; cur < end; cur += PAGE_SIZE) {
+		pfn = __phys_to_pfn(cur);
+		WARN_ON(unshare_pfn_hyp(pfn));
+	}
+}
+
 /**
  * create_hyp_mappings - duplicate a kernel virtual address range in Hyp mode
  * @from:	The virtual kernel start address of the range
@@ -316,12 +473,8 @@ int create_hyp_mappings(void *from, void *to, enum kvm_pgtable_prot prot)
 	if (is_kernel_in_hyp_mode())
 		return 0;
 
-	if (!kvm_host_owns_hyp_mappings()) {
-		if (WARN_ON(prot != PAGE_HYP))
-			return -EPERM;
-		return pkvm_share_hyp(kvm_kaddr_to_phys(from),
-				      kvm_kaddr_to_phys(to));
-	}
+	if (!kvm_host_owns_hyp_mappings())
+		return -EPERM;
 
 	start = start & PAGE_MASK;
 	end = PAGE_ALIGN(end);
@@ -339,23 +492,22 @@ int create_hyp_mappings(void *from, void *to, enum kvm_pgtable_prot prot)
 	return 0;
 }
 
-static int __create_hyp_private_mapping(phys_addr_t phys_addr, size_t size,
-					unsigned long *haddr,
-					enum kvm_pgtable_prot prot)
+
+/**
+ * hyp_alloc_private_va_range - Allocates a private VA range.
+ * @size:	The size of the VA range to reserve.
+ * @haddr:	The hypervisor virtual start address of the allocation.
+ *
+ * The private virtual address (VA) range is allocated below io_map_base
+ * and aligned based on the order of @size.
+ *
+ * Return: 0 on success or negative error code on failure.
+ */
+int hyp_alloc_private_va_range(size_t size, unsigned long *haddr)
 {
 	unsigned long base;
 	int ret = 0;
 
-	if (!kvm_host_owns_hyp_mappings()) {
-		base = kvm_call_hyp_nvhe(__pkvm_create_private_mapping,
-					 phys_addr, size, prot);
-		if (IS_ERR_OR_NULL((void *)base))
-			return PTR_ERR((void *)base);
-		*haddr = base;
-
-		return 0;
-	}
-
 	mutex_lock(&kvm_hyp_pgd_mutex);
 
 	/*
@@ -366,8 +518,10 @@ static int __create_hyp_private_mapping(phys_addr_t phys_addr, size_t size,
 	 *
 	 * The allocated size is always a multiple of PAGE_SIZE.
 	 */
-	size = PAGE_ALIGN(size + offset_in_page(phys_addr));
-	base = io_map_base - size;
+	base = io_map_base - PAGE_ALIGN(size);
+
+	/* Align the allocation based on the order of its size */
+	base = ALIGN_DOWN(base, PAGE_SIZE << get_order(size));
 
 	/*
 	 * Verify that BIT(VA_BITS - 1) hasn't been flipped by
@@ -377,19 +531,40 @@ static int __create_hyp_private_mapping(phys_addr_t phys_addr, size_t size,
 	if ((base ^ io_map_base) & BIT(VA_BITS - 1))
 		ret = -ENOMEM;
 	else
-		io_map_base = base;
+		*haddr = io_map_base = base;
 
 	mutex_unlock(&kvm_hyp_pgd_mutex);
 
+	return ret;
+}
+
+static int __create_hyp_private_mapping(phys_addr_t phys_addr, size_t size,
+					unsigned long *haddr,
+					enum kvm_pgtable_prot prot)
+{
+	unsigned long addr;
+	int ret = 0;
+
+	if (!kvm_host_owns_hyp_mappings()) {
+		addr = kvm_call_hyp_nvhe(__pkvm_create_private_mapping,
+					 phys_addr, size, prot);
+		if (IS_ERR_VALUE(addr))
+			return addr;
+		*haddr = addr;
+
+		return 0;
+	}
+
+	size = PAGE_ALIGN(size + offset_in_page(phys_addr));
+	ret = hyp_alloc_private_va_range(size, &addr);
 	if (ret)
-		goto out;
+		return ret;
 
-	ret = __create_hyp_mappings(base, size, phys_addr, prot);
+	ret = __create_hyp_mappings(addr, size, phys_addr, prot);
 	if (ret)
-		goto out;
+		return ret;
 
-	*haddr = base + offset_in_page(phys_addr);
-out:
+	*haddr = addr + offset_in_page(phys_addr);
 	return ret;
 }
 
@@ -407,6 +582,9 @@ int create_hyp_io_mappings(phys_addr_t phys_addr, size_t size,
 	unsigned long addr;
 	int ret;
 
+	if (is_protected_kvm_enabled())
+		return -EPERM;
+
 	*kaddr = ioremap(phys_addr, size);
 	if (!*kaddr)
 		return -ENOMEM;
@@ -482,10 +660,10 @@ static int get_user_mapping_size(struct kvm *kvm, u64 addr)
 
 static struct kvm_pgtable_mm_ops kvm_s2_mm_ops = {
 	.zalloc_page		= stage2_memcache_zalloc_page,
-	.zalloc_pages_exact	= kvm_host_zalloc_pages_exact,
-	.free_pages_exact	= free_pages_exact,
+	.zalloc_pages_exact	= kvm_s2_zalloc_pages_exact,
+	.free_pages_exact	= kvm_s2_free_pages_exact,
 	.get_page		= kvm_host_get_page,
-	.put_page		= kvm_host_put_page,
+	.put_page		= kvm_s2_put_page,
 	.page_count		= kvm_host_page_count,
 	.phys_to_virt		= kvm_host_va,
 	.virt_to_phys		= kvm_host_pa,
@@ -494,7 +672,7 @@ static struct kvm_pgtable_mm_ops kvm_s2_mm_ops = {
 };
 
 /**
- * kvm_init_stage2_mmu - Initialise a S2 MMU strucrure
+ * kvm_init_stage2_mmu - Initialise a S2 MMU structure
  * @kvm:	The pointer to the KVM structure
  * @mmu:	The pointer to the s2 MMU structure
  *
@@ -516,7 +694,8 @@ int kvm_init_stage2_mmu(struct kvm *kvm, struct kvm_s2_mmu *mmu)
 	if (!pgt)
 		return -ENOMEM;
 
-	err = kvm_pgtable_stage2_init(pgt, &kvm->arch, &kvm_s2_mm_ops);
+	mmu->arch = &kvm->arch;
+	err = kvm_pgtable_stage2_init(pgt, mmu, &kvm_s2_mm_ops);
 	if (err)
 		goto out_free_pgtable;
 
@@ -529,10 +708,8 @@ int kvm_init_stage2_mmu(struct kvm *kvm, struct kvm_s2_mmu *mmu)
 	for_each_possible_cpu(cpu)
 		*per_cpu_ptr(mmu->last_vcpu_ran, cpu) = -1;
 
-	mmu->arch = &kvm->arch;
 	mmu->pgt = pgt;
 	mmu->pgd_phys = __pa(pgt->pgd);
-	WRITE_ONCE(mmu->vmid.vmid_gen, 0);
 	return 0;
 
 out_destroy_pgtable:
@@ -595,17 +772,17 @@ void stage2_unmap_vm(struct kvm *kvm)
 {
 	struct kvm_memslots *slots;
 	struct kvm_memory_slot *memslot;
-	int idx;
+	int idx, bkt;
 
 	idx = srcu_read_lock(&kvm->srcu);
 	mmap_read_lock(current->mm);
-	spin_lock(&kvm->mmu_lock);
+	write_lock(&kvm->mmu_lock);
 
 	slots = kvm_memslots(kvm);
-	kvm_for_each_memslot(memslot, slots)
+	kvm_for_each_memslot(memslot, bkt, slots)
 		stage2_unmap_memslot(kvm, memslot);
 
-	spin_unlock(&kvm->mmu_lock);
+	write_unlock(&kvm->mmu_lock);
 	mmap_read_unlock(current->mm);
 	srcu_read_unlock(&kvm->srcu, idx);
 }
@@ -615,14 +792,14 @@ void kvm_free_stage2_pgd(struct kvm_s2_mmu *mmu)
 	struct kvm *kvm = kvm_s2_mmu_to_kvm(mmu);
 	struct kvm_pgtable *pgt = NULL;
 
-	spin_lock(&kvm->mmu_lock);
+	write_lock(&kvm->mmu_lock);
 	pgt = mmu->pgt;
 	if (pgt) {
 		mmu->pgd_phys = 0;
 		mmu->pgt = NULL;
 		free_percpu(mmu->last_vcpu_ran);
 	}
-	spin_unlock(&kvm->mmu_lock);
+	write_unlock(&kvm->mmu_lock);
 
 	if (pgt) {
 		kvm_pgtable_stage2_destroy(pgt);
@@ -644,12 +821,15 @@ int kvm_phys_addr_ioremap(struct kvm *kvm, phys_addr_t guest_ipa,
 {
 	phys_addr_t addr;
 	int ret = 0;
-	struct kvm_mmu_memory_cache cache = { 0, __GFP_ZERO, NULL, };
+	struct kvm_mmu_memory_cache cache = { .gfp_zero = __GFP_ZERO };
 	struct kvm_pgtable *pgt = kvm->arch.mmu.pgt;
 	enum kvm_pgtable_prot prot = KVM_PGTABLE_PROT_DEVICE |
 				     KVM_PGTABLE_PROT_R |
 				     (writable ? KVM_PGTABLE_PROT_W : 0);
 
+	if (is_protected_kvm_enabled())
+		return -EPERM;
+
 	size += offset_in_page(guest_ipa);
 	guest_ipa &= PAGE_MASK;
 
@@ -659,10 +839,10 @@ int kvm_phys_addr_ioremap(struct kvm *kvm, phys_addr_t guest_ipa,
 		if (ret)
 			break;
 
-		spin_lock(&kvm->mmu_lock);
+		write_lock(&kvm->mmu_lock);
 		ret = kvm_pgtable_stage2_map(pgt, addr, PAGE_SIZE, pa, prot,
 					     &cache);
-		spin_unlock(&kvm->mmu_lock);
+		write_unlock(&kvm->mmu_lock);
 		if (ret)
 			break;
 
@@ -710,9 +890,9 @@ static void kvm_mmu_wp_memory_region(struct kvm *kvm, int slot)
 	start = memslot->base_gfn << PAGE_SHIFT;
 	end = (memslot->base_gfn + memslot->npages) << PAGE_SHIFT;
 
-	spin_lock(&kvm->mmu_lock);
+	write_lock(&kvm->mmu_lock);
 	stage2_wp_range(&kvm->arch.mmu, start, end);
-	spin_unlock(&kvm->mmu_lock);
+	write_unlock(&kvm->mmu_lock);
 	kvm_flush_remote_tlbs(kvm);
 }
 
@@ -848,7 +1028,7 @@ transparent_hugepage_adjust(struct kvm *kvm, struct kvm_memory_slot *memslot,
 		 * THP doesn't start to split while we are adjusting the
 		 * refcounts.
 		 *
-		 * We are sure this doesn't happen, because mmu_notifier_retry
+		 * We are sure this doesn't happen, because mmu_invalidate_retry
 		 * was successful and we are holding the mmu_lock, so if this
 		 * THP is trying to split, it will be blocked in the mmu
 		 * notifier before touching any of the pages, specifically
@@ -956,6 +1136,7 @@ static int user_mem_abort(struct kvm_vcpu *vcpu, phys_addr_t fault_ipa,
 	gfn_t gfn;
 	kvm_pfn_t pfn;
 	bool logging_active = memslot_is_logging(memslot);
+	bool use_read_lock = false;
 	unsigned long fault_level = kvm_vcpu_trap_get_fault_level(vcpu);
 	unsigned long vma_pagesize, fault_granule;
 	enum kvm_pgtable_prot prot = KVM_PGTABLE_PROT_R;
@@ -990,6 +1171,8 @@ static int user_mem_abort(struct kvm_vcpu *vcpu, phys_addr_t fault_ipa,
 	if (logging_active) {
 		force_pte = true;
 		vma_shift = PAGE_SHIFT;
+		use_read_lock = (fault_status == FSC_PERM && write_fault &&
+				 fault_granule == PAGE_SIZE);
 	} else {
 		vma_shift = get_vma_page_shift(vma, hva);
 	}
@@ -1040,9 +1223,9 @@ static int user_mem_abort(struct kvm_vcpu *vcpu, phys_addr_t fault_ipa,
 			return ret;
 	}
 
-	mmu_seq = vcpu->kvm->mmu_notifier_seq;
+	mmu_seq = vcpu->kvm->mmu_invalidate_seq;
 	/*
-	 * Ensure the read of mmu_notifier_seq happens before we call
+	 * Ensure the read of mmu_invalidate_seq happens before we call
 	 * gfn_to_pfn_prot (which calls get_user_pages), so that we don't risk
 	 * the page we just got a reference to gets unmapped before we have a
 	 * chance to grab the mmu_lock, which ensure that if the page gets
@@ -1088,9 +1271,17 @@ static int user_mem_abort(struct kvm_vcpu *vcpu, phys_addr_t fault_ipa,
 	if (exec_fault && device)
 		return -ENOEXEC;
 
-	spin_lock(&kvm->mmu_lock);
+	/*
+	 * To reduce MMU contentions and enhance concurrency during dirty
+	 * logging dirty logging, only acquire read lock for permission
+	 * relaxation.
+	 */
+	if (use_read_lock)
+		read_lock(&kvm->mmu_lock);
+	else
+		write_lock(&kvm->mmu_lock);
 	pgt = vcpu->arch.hw_mmu->pgt;
-	if (mmu_notifier_retry(kvm, mmu_seq))
+	if (mmu_invalidate_retry(kvm, mmu_seq))
 		goto out_unlock;
 
 	/*
@@ -1135,6 +1326,8 @@ static int user_mem_abort(struct kvm_vcpu *vcpu, phys_addr_t fault_ipa,
 	if (fault_status == FSC_PERM && vma_pagesize == fault_granule) {
 		ret = kvm_pgtable_stage2_relax_perms(pgt, fault_ipa, prot);
 	} else {
+		WARN_ONCE(use_read_lock, "Attempted stage-2 map outside of write lock\n");
+
 		ret = kvm_pgtable_stage2_map(pgt, fault_ipa, vma_pagesize,
 					     __pfn_to_phys(pfn), prot,
 					     memcache);
@@ -1147,7 +1340,10 @@ static int user_mem_abort(struct kvm_vcpu *vcpu, phys_addr_t fault_ipa,
 	}
 
 out_unlock:
-	spin_unlock(&kvm->mmu_lock);
+	if (use_read_lock)
+		read_unlock(&kvm->mmu_lock);
+	else
+		write_unlock(&kvm->mmu_lock);
 	kvm_set_pfn_accessed(pfn);
 	kvm_release_pfn_clean(pfn);
 	return ret != -EAGAIN ? ret : 0;
@@ -1162,10 +1358,10 @@ static void handle_access_fault(struct kvm_vcpu *vcpu, phys_addr_t fault_ipa)
 
 	trace_kvm_access_fault(fault_ipa);
 
-	spin_lock(&vcpu->kvm->mmu_lock);
+	write_lock(&vcpu->kvm->mmu_lock);
 	mmu = vcpu->arch.hw_mmu;
 	kpte = kvm_pgtable_stage2_mkyoung(mmu->pgt, fault_ipa);
-	spin_unlock(&vcpu->kvm->mmu_lock);
+	write_unlock(&vcpu->kvm->mmu_lock);
 
 	pte = __pte(kpte);
 	if (pte_valid(pte))
@@ -1198,6 +1394,25 @@ int kvm_handle_guest_abort(struct kvm_vcpu *vcpu)
 	fault_ipa = kvm_vcpu_get_fault_ipa(vcpu);
 	is_iabt = kvm_vcpu_trap_is_iabt(vcpu);
 
+	if (fault_status == FSC_FAULT) {
+		/* Beyond sanitised PARange (which is the IPA limit) */
+		if (fault_ipa >= BIT_ULL(get_kvm_ipa_limit())) {
+			kvm_inject_size_fault(vcpu);
+			return 1;
+		}
+
+		/* Falls between the IPA range and the PARange? */
+		if (fault_ipa >= BIT_ULL(vcpu->arch.hw_mmu->pgt->ia_bits)) {
+			fault_ipa |= kvm_vcpu_get_hfar(vcpu) & GENMASK(11, 0);
+
+			if (is_iabt)
+				kvm_inject_pabt(vcpu, fault_ipa);
+			else
+				kvm_inject_dabt(vcpu, fault_ipa);
+			return 1;
+		}
+	}
+
 	/* Synchronous External Abort? */
 	if (kvm_vcpu_abt_issea(vcpu)) {
 		/*
@@ -1463,7 +1678,6 @@ out:
 }
 
 void kvm_arch_commit_memory_region(struct kvm *kvm,
-				   const struct kvm_userspace_memory_region *mem,
 				   struct kvm_memory_slot *old,
 				   const struct kvm_memory_slot *new,
 				   enum kvm_mr_change change)
@@ -1473,25 +1687,24 @@ void kvm_arch_commit_memory_region(struct kvm *kvm,
 	 * allocated dirty_bitmap[], dirty pages will be tracked while the
 	 * memory slot is write protected.
 	 */
-	if (change != KVM_MR_DELETE && mem->flags & KVM_MEM_LOG_DIRTY_PAGES) {
+	if (change != KVM_MR_DELETE && new->flags & KVM_MEM_LOG_DIRTY_PAGES) {
 		/*
 		 * If we're with initial-all-set, we don't need to write
 		 * protect any pages because they're all reported as dirty.
 		 * Huge pages and normal pages will be write protect gradually.
 		 */
 		if (!kvm_dirty_log_manual_protect_and_init_set(kvm)) {
-			kvm_mmu_wp_memory_region(kvm, mem->slot);
+			kvm_mmu_wp_memory_region(kvm, new->id);
 		}
 	}
 }
 
 int kvm_arch_prepare_memory_region(struct kvm *kvm,
-				   struct kvm_memory_slot *memslot,
-				   const struct kvm_userspace_memory_region *mem,
+				   const struct kvm_memory_slot *old,
+				   struct kvm_memory_slot *new,
 				   enum kvm_mr_change change)
 {
-	hva_t hva = mem->userspace_addr;
-	hva_t reg_end = hva + mem->memory_size;
+	hva_t hva, reg_end;
 	int ret = 0;
 
 	if (change != KVM_MR_CREATE && change != KVM_MR_MOVE &&
@@ -1502,9 +1715,12 @@ int kvm_arch_prepare_memory_region(struct kvm *kvm,
 	 * Prevent userspace from creating a memory region outside of the IPA
 	 * space addressable by the KVM guest IPA space.
 	 */
-	if ((memslot->base_gfn + memslot->npages) > (kvm_phys_size(kvm) >> PAGE_SHIFT))
+	if ((new->base_gfn + new->npages) > (kvm_phys_size(kvm) >> PAGE_SHIFT))
 		return -EFAULT;
 
+	hva = new->userspace_addr;
+	reg_end = hva + (new->npages << PAGE_SHIFT);
+
 	mmap_read_lock(current->mm);
 	/*
 	 * A memory region could potentially cover multiple VMAs, and any holes
@@ -1536,7 +1752,7 @@ int kvm_arch_prepare_memory_region(struct kvm *kvm,
 
 		if (vma->vm_flags & VM_PFNMAP) {
 			/* IO region dirty page logging not allowed */
-			if (memslot->flags & KVM_MEM_LOG_DIRTY_PAGES) {
+			if (new->flags & KVM_MEM_LOG_DIRTY_PAGES) {
 				ret = -EINVAL;
 				break;
 			}
@@ -1567,9 +1783,9 @@ void kvm_arch_flush_shadow_memslot(struct kvm *kvm,
 	gpa_t gpa = slot->base_gfn << PAGE_SHIFT;
 	phys_addr_t size = slot->npages << PAGE_SHIFT;
 
-	spin_lock(&kvm->mmu_lock);
+	write_lock(&kvm->mmu_lock);
 	unmap_stage2_range(&kvm->arch.mmu, gpa, size);
-	spin_unlock(&kvm->mmu_lock);
+	write_unlock(&kvm->mmu_lock);
 }
 
 /*
diff --git a/arch/arm64/kvm/perf.c b/arch/arm64/kvm/perf.c
deleted file mode 100644
index c84fe24b2ea1..000000000000
--- a/arch/arm64/kvm/perf.c
+++ /dev/null
@@ -1,59 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Based on the x86 implementation.
- *
- * Copyright (C) 2012 ARM Ltd.
- * Author: Marc Zyngier <marc.zyngier@arm.com>
- */
-
-#include <linux/perf_event.h>
-#include <linux/kvm_host.h>
-
-#include <asm/kvm_emulate.h>
-
-DEFINE_STATIC_KEY_FALSE(kvm_arm_pmu_available);
-
-static int kvm_is_in_guest(void)
-{
-        return kvm_get_running_vcpu() != NULL;
-}
-
-static int kvm_is_user_mode(void)
-{
-	struct kvm_vcpu *vcpu;
-
-	vcpu = kvm_get_running_vcpu();
-
-	if (vcpu)
-		return !vcpu_mode_priv(vcpu);
-
-	return 0;
-}
-
-static unsigned long kvm_get_guest_ip(void)
-{
-	struct kvm_vcpu *vcpu;
-
-	vcpu = kvm_get_running_vcpu();
-
-	if (vcpu)
-		return *vcpu_pc(vcpu);
-
-	return 0;
-}
-
-static struct perf_guest_info_callbacks kvm_guest_cbs = {
-	.is_in_guest	= kvm_is_in_guest,
-	.is_user_mode	= kvm_is_user_mode,
-	.get_guest_ip	= kvm_get_guest_ip,
-};
-
-int kvm_perf_init(void)
-{
-	return perf_register_guest_info_callbacks(&kvm_guest_cbs);
-}
-
-int kvm_perf_teardown(void)
-{
-	return perf_unregister_guest_info_callbacks(&kvm_guest_cbs);
-}
diff --git a/arch/arm64/kvm/pkvm.c b/arch/arm64/kvm/pkvm.c
new file mode 100644
index 000000000000..ebecb7c045f4
--- /dev/null
+++ b/arch/arm64/kvm/pkvm.c
@@ -0,0 +1,109 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2020 - Google LLC
+ * Author: Quentin Perret <qperret@google.com>
+ */
+
+#include <linux/kvm_host.h>
+#include <linux/memblock.h>
+#include <linux/sort.h>
+
+#include <asm/kvm_pkvm.h>
+
+#include "hyp_constants.h"
+
+static struct memblock_region *hyp_memory = kvm_nvhe_sym(hyp_memory);
+static unsigned int *hyp_memblock_nr_ptr = &kvm_nvhe_sym(hyp_memblock_nr);
+
+phys_addr_t hyp_mem_base;
+phys_addr_t hyp_mem_size;
+
+static int cmp_hyp_memblock(const void *p1, const void *p2)
+{
+	const struct memblock_region *r1 = p1;
+	const struct memblock_region *r2 = p2;
+
+	return r1->base < r2->base ? -1 : (r1->base > r2->base);
+}
+
+static void __init sort_memblock_regions(void)
+{
+	sort(hyp_memory,
+	     *hyp_memblock_nr_ptr,
+	     sizeof(struct memblock_region),
+	     cmp_hyp_memblock,
+	     NULL);
+}
+
+static int __init register_memblock_regions(void)
+{
+	struct memblock_region *reg;
+
+	for_each_mem_region(reg) {
+		if (*hyp_memblock_nr_ptr >= HYP_MEMBLOCK_REGIONS)
+			return -ENOMEM;
+
+		hyp_memory[*hyp_memblock_nr_ptr] = *reg;
+		(*hyp_memblock_nr_ptr)++;
+	}
+	sort_memblock_regions();
+
+	return 0;
+}
+
+void __init kvm_hyp_reserve(void)
+{
+	u64 nr_pages, prev, hyp_mem_pages = 0;
+	int ret;
+
+	if (!is_hyp_mode_available() || is_kernel_in_hyp_mode())
+		return;
+
+	if (kvm_get_mode() != KVM_MODE_PROTECTED)
+		return;
+
+	ret = register_memblock_regions();
+	if (ret) {
+		*hyp_memblock_nr_ptr = 0;
+		kvm_err("Failed to register hyp memblocks: %d\n", ret);
+		return;
+	}
+
+	hyp_mem_pages += hyp_s1_pgtable_pages();
+	hyp_mem_pages += host_s2_pgtable_pages();
+
+	/*
+	 * The hyp_vmemmap needs to be backed by pages, but these pages
+	 * themselves need to be present in the vmemmap, so compute the number
+	 * of pages needed by looking for a fixed point.
+	 */
+	nr_pages = 0;
+	do {
+		prev = nr_pages;
+		nr_pages = hyp_mem_pages + prev;
+		nr_pages = DIV_ROUND_UP(nr_pages * STRUCT_HYP_PAGE_SIZE,
+					PAGE_SIZE);
+		nr_pages += __hyp_pgtable_max_pages(nr_pages);
+	} while (nr_pages != prev);
+	hyp_mem_pages += nr_pages;
+
+	/*
+	 * Try to allocate a PMD-aligned region to reduce TLB pressure once
+	 * this is unmapped from the host stage-2, and fallback to PAGE_SIZE.
+	 */
+	hyp_mem_size = hyp_mem_pages << PAGE_SHIFT;
+	hyp_mem_base = memblock_phys_alloc(ALIGN(hyp_mem_size, PMD_SIZE),
+					   PMD_SIZE);
+	if (!hyp_mem_base)
+		hyp_mem_base = memblock_phys_alloc(hyp_mem_size, PAGE_SIZE);
+	else
+		hyp_mem_size = ALIGN(hyp_mem_size, PMD_SIZE);
+
+	if (!hyp_mem_base) {
+		kvm_err("Failed to reserve hyp memory\n");
+		return;
+	}
+
+	kvm_info("Reserved %lld MiB at 0x%llx\n", hyp_mem_size >> 20,
+		 hyp_mem_base);
+}
diff --git a/arch/arm64/kvm/pmu-emul.c b/arch/arm64/kvm/pmu-emul.c
index a5e4bbf5e68f..0003c7d37533 100644
--- a/arch/arm64/kvm/pmu-emul.c
+++ b/arch/arm64/kvm/pmu-emul.c
@@ -7,6 +7,7 @@
 #include <linux/cpu.h>
 #include <linux/kvm.h>
 #include <linux/kvm_host.h>
+#include <linux/list.h>
 #include <linux/perf_event.h>
 #include <linux/perf/arm_pmu.h>
 #include <linux/uaccess.h>
@@ -14,6 +15,11 @@
 #include <kvm/arm_pmu.h>
 #include <kvm/arm_vgic.h>
 
+DEFINE_STATIC_KEY_FALSE(kvm_arm_pmu_available);
+
+static LIST_HEAD(arm_pmus);
+static DEFINE_MUTEX(arm_pmus_lock);
+
 static void kvm_pmu_create_perf_event(struct kvm_vcpu *vcpu, u64 select_idx);
 static void kvm_pmu_update_pmc_chained(struct kvm_vcpu *vcpu, u64 select_idx);
 static void kvm_pmu_stop_counter(struct kvm_vcpu *vcpu, struct kvm_pmc *pmc);
@@ -22,15 +28,20 @@ static void kvm_pmu_stop_counter(struct kvm_vcpu *vcpu, struct kvm_pmc *pmc);
 
 static u32 kvm_pmu_event_mask(struct kvm *kvm)
 {
-	switch (kvm->arch.pmuver) {
-	case ID_AA64DFR0_PMUVER_8_0:
+	unsigned int pmuver;
+
+	pmuver = kvm->arch.arm_pmu->pmuver;
+
+	switch (pmuver) {
+	case ID_AA64DFR0_EL1_PMUVer_IMP:
 		return GENMASK(9, 0);
-	case ID_AA64DFR0_PMUVER_8_1:
-	case ID_AA64DFR0_PMUVER_8_4:
-	case ID_AA64DFR0_PMUVER_8_5:
+	case ID_AA64DFR0_EL1_PMUVer_V3P1:
+	case ID_AA64DFR0_EL1_PMUVer_V3P4:
+	case ID_AA64DFR0_EL1_PMUVer_V3P5:
+	case ID_AA64DFR0_EL1_PMUVer_V3P7:
 		return GENMASK(15, 0);
 	default:		/* Shouldn't be here, just for sanity */
-		WARN_ONCE(1, "Unknown PMU version %d\n", kvm->arch.pmuver);
+		WARN_ONCE(1, "Unknown PMU version %d\n", pmuver);
 		return 0;
 	}
 }
@@ -166,6 +177,9 @@ u64 kvm_pmu_get_counter_value(struct kvm_vcpu *vcpu, u64 select_idx)
 	struct kvm_pmu *pmu = &vcpu->arch.pmu;
 	struct kvm_pmc *pmc = &pmu->pmc[select_idx];
 
+	if (!kvm_vcpu_has_pmu(vcpu))
+		return 0;
+
 	counter = kvm_pmu_get_pair_counter_value(vcpu, pmc);
 
 	if (kvm_pmu_pmc_is_chained(pmc) &&
@@ -187,6 +201,9 @@ void kvm_pmu_set_counter_value(struct kvm_vcpu *vcpu, u64 select_idx, u64 val)
 {
 	u64 reg;
 
+	if (!kvm_vcpu_has_pmu(vcpu))
+		return;
+
 	reg = (select_idx == ARMV8_PMU_CYCLE_IDX)
 	      ? PMCCNTR_EL0 : PMEVCNTR0_EL0 + select_idx;
 	__vcpu_sys_reg(vcpu, reg) += (s64)val - kvm_pmu_get_counter_value(vcpu, select_idx);
@@ -311,6 +328,9 @@ void kvm_pmu_enable_counter_mask(struct kvm_vcpu *vcpu, u64 val)
 	struct kvm_pmu *pmu = &vcpu->arch.pmu;
 	struct kvm_pmc *pmc;
 
+	if (!kvm_vcpu_has_pmu(vcpu))
+		return;
+
 	if (!(__vcpu_sys_reg(vcpu, PMCR_EL0) & ARMV8_PMU_PMCR_E) || !val)
 		return;
 
@@ -346,7 +366,7 @@ void kvm_pmu_disable_counter_mask(struct kvm_vcpu *vcpu, u64 val)
 	struct kvm_pmu *pmu = &vcpu->arch.pmu;
 	struct kvm_pmc *pmc;
 
-	if (!val)
+	if (!kvm_vcpu_has_pmu(vcpu) || !val)
 		return;
 
 	for (i = 0; i < ARMV8_PMU_MAX_COUNTERS; i++) {
@@ -516,6 +536,9 @@ void kvm_pmu_software_increment(struct kvm_vcpu *vcpu, u64 val)
 	struct kvm_pmu *pmu = &vcpu->arch.pmu;
 	int i;
 
+	if (!kvm_vcpu_has_pmu(vcpu))
+		return;
+
 	if (!(__vcpu_sys_reg(vcpu, PMCR_EL0) & ARMV8_PMU_PMCR_E))
 		return;
 
@@ -565,6 +588,9 @@ void kvm_pmu_handle_pmcr(struct kvm_vcpu *vcpu, u64 val)
 {
 	int i;
 
+	if (!kvm_vcpu_has_pmu(vcpu))
+		return;
+
 	if (val & ARMV8_PMU_PMCR_E) {
 		kvm_pmu_enable_counter_mask(vcpu,
 		       __vcpu_sys_reg(vcpu, PMCNTENSET_EL0));
@@ -597,6 +623,7 @@ static bool kvm_pmu_counter_is_enabled(struct kvm_vcpu *vcpu, u64 select_idx)
  */
 static void kvm_pmu_create_perf_event(struct kvm_vcpu *vcpu, u64 select_idx)
 {
+	struct arm_pmu *arm_pmu = vcpu->kvm->arch.arm_pmu;
 	struct kvm_pmu *pmu = &vcpu->arch.pmu;
 	struct kvm_pmc *pmc;
 	struct perf_event *event;
@@ -633,7 +660,7 @@ static void kvm_pmu_create_perf_event(struct kvm_vcpu *vcpu, u64 select_idx)
 		return;
 
 	memset(&attr, 0, sizeof(struct perf_event_attr));
-	attr.type = PERF_TYPE_RAW;
+	attr.type = arm_pmu->pmu.type;
 	attr.size = sizeof(attr);
 	attr.pinned = 1;
 	attr.disabled = !kvm_pmu_counter_is_enabled(vcpu, pmc->idx);
@@ -727,6 +754,9 @@ void kvm_pmu_set_counter_event_type(struct kvm_vcpu *vcpu, u64 data,
 {
 	u64 reg, mask;
 
+	if (!kvm_vcpu_has_pmu(vcpu))
+		return;
+
 	mask  =  ARMV8_PMU_EVTYPE_MASK;
 	mask &= ~ARMV8_PMU_EVTYPE_EVENT;
 	mask |= kvm_pmu_event_mask(vcpu->kvm);
@@ -742,17 +772,32 @@ void kvm_pmu_set_counter_event_type(struct kvm_vcpu *vcpu, u64 data,
 
 void kvm_host_pmu_init(struct arm_pmu *pmu)
 {
-	if (pmu->pmuver != 0 && pmu->pmuver != ID_AA64DFR0_PMUVER_IMP_DEF &&
-	    !kvm_arm_support_pmu_v3() && !is_protected_kvm_enabled())
+	struct arm_pmu_entry *entry;
+
+	if (pmu->pmuver == 0 || pmu->pmuver == ID_AA64DFR0_EL1_PMUVer_IMP_DEF)
+		return;
+
+	mutex_lock(&arm_pmus_lock);
+
+	entry = kmalloc(sizeof(*entry), GFP_KERNEL);
+	if (!entry)
+		goto out_unlock;
+
+	entry->arm_pmu = pmu;
+	list_add_tail(&entry->entry, &arm_pmus);
+
+	if (list_is_singular(&arm_pmus))
 		static_branch_enable(&kvm_arm_pmu_available);
+
+out_unlock:
+	mutex_unlock(&arm_pmus_lock);
 }
 
-static int kvm_pmu_probe_pmuver(void)
+static struct arm_pmu *kvm_pmu_probe_armpmu(void)
 {
 	struct perf_event_attr attr = { };
 	struct perf_event *event;
-	struct arm_pmu *pmu;
-	int pmuver = ID_AA64DFR0_PMUVER_IMP_DEF;
+	struct arm_pmu *pmu = NULL;
 
 	/*
 	 * Create a dummy event that only counts user cycles. As we'll never
@@ -777,19 +822,20 @@ static int kvm_pmu_probe_pmuver(void)
 	if (IS_ERR(event)) {
 		pr_err_once("kvm: pmu event creation failed %ld\n",
 			    PTR_ERR(event));
-		return ID_AA64DFR0_PMUVER_IMP_DEF;
+		return NULL;
 	}
 
 	if (event->pmu) {
 		pmu = to_arm_pmu(event->pmu);
-		if (pmu->pmuver)
-			pmuver = pmu->pmuver;
+		if (pmu->pmuver == 0 ||
+		    pmu->pmuver == ID_AA64DFR0_EL1_PMUVer_IMP_DEF)
+			pmu = NULL;
 	}
 
 	perf_event_disable(event);
 	perf_event_release_kernel(event);
 
-	return pmuver;
+	return pmu;
 }
 
 u64 kvm_pmu_get_pmceid(struct kvm_vcpu *vcpu, bool pmceid1)
@@ -798,6 +844,9 @@ u64 kvm_pmu_get_pmceid(struct kvm_vcpu *vcpu, bool pmceid1)
 	u64 val, mask = 0;
 	int base, i, nr_events;
 
+	if (!kvm_vcpu_has_pmu(vcpu))
+		return 0;
+
 	if (!pmceid1) {
 		val = read_sysreg(pmceid0_el0);
 		base = 0;
@@ -807,7 +856,7 @@ u64 kvm_pmu_get_pmceid(struct kvm_vcpu *vcpu, bool pmceid1)
 		 * Don't advertise STALL_SLOT, as PMMIR_EL0 is handled
 		 * as RAZ
 		 */
-		if (vcpu->kvm->arch.pmuver >= ID_AA64DFR0_PMUVER_8_4)
+		if (vcpu->kvm->arch.arm_pmu->pmuver >= ID_AA64DFR0_EL1_PMUVer_V3P4)
 			val &= ~BIT_ULL(ARMV8_PMUV3_PERFCTR_STALL_SLOT - 32);
 		base = 32;
 	}
@@ -900,7 +949,7 @@ static int kvm_arm_pmu_v3_init(struct kvm_vcpu *vcpu)
  */
 static bool pmu_irq_is_valid(struct kvm *kvm, int irq)
 {
-	int i;
+	unsigned long i;
 	struct kvm_vcpu *vcpu;
 
 	kvm_for_each_vcpu(i, vcpu, kvm) {
@@ -919,26 +968,64 @@ static bool pmu_irq_is_valid(struct kvm *kvm, int irq)
 	return true;
 }
 
+static int kvm_arm_pmu_v3_set_pmu(struct kvm_vcpu *vcpu, int pmu_id)
+{
+	struct kvm *kvm = vcpu->kvm;
+	struct arm_pmu_entry *entry;
+	struct arm_pmu *arm_pmu;
+	int ret = -ENXIO;
+
+	mutex_lock(&kvm->lock);
+	mutex_lock(&arm_pmus_lock);
+
+	list_for_each_entry(entry, &arm_pmus, entry) {
+		arm_pmu = entry->arm_pmu;
+		if (arm_pmu->pmu.type == pmu_id) {
+			if (test_bit(KVM_ARCH_FLAG_HAS_RAN_ONCE, &kvm->arch.flags) ||
+			    (kvm->arch.pmu_filter && kvm->arch.arm_pmu != arm_pmu)) {
+				ret = -EBUSY;
+				break;
+			}
+
+			kvm->arch.arm_pmu = arm_pmu;
+			cpumask_copy(kvm->arch.supported_cpus, &arm_pmu->supported_cpus);
+			ret = 0;
+			break;
+		}
+	}
+
+	mutex_unlock(&arm_pmus_lock);
+	mutex_unlock(&kvm->lock);
+	return ret;
+}
+
 int kvm_arm_pmu_v3_set_attr(struct kvm_vcpu *vcpu, struct kvm_device_attr *attr)
 {
+	struct kvm *kvm = vcpu->kvm;
+
 	if (!kvm_vcpu_has_pmu(vcpu))
 		return -ENODEV;
 
 	if (vcpu->arch.pmu.created)
 		return -EBUSY;
 
-	if (!vcpu->kvm->arch.pmuver)
-		vcpu->kvm->arch.pmuver = kvm_pmu_probe_pmuver();
-
-	if (vcpu->kvm->arch.pmuver == ID_AA64DFR0_PMUVER_IMP_DEF)
-		return -ENODEV;
+	mutex_lock(&kvm->lock);
+	if (!kvm->arch.arm_pmu) {
+		/* No PMU set, get the default one */
+		kvm->arch.arm_pmu = kvm_pmu_probe_armpmu();
+		if (!kvm->arch.arm_pmu) {
+			mutex_unlock(&kvm->lock);
+			return -ENODEV;
+		}
+	}
+	mutex_unlock(&kvm->lock);
 
 	switch (attr->attr) {
 	case KVM_ARM_VCPU_PMU_V3_IRQ: {
 		int __user *uaddr = (int __user *)(long)attr->addr;
 		int irq;
 
-		if (!irqchip_in_kernel(vcpu->kvm))
+		if (!irqchip_in_kernel(kvm))
 			return -EINVAL;
 
 		if (get_user(irq, uaddr))
@@ -948,7 +1035,7 @@ int kvm_arm_pmu_v3_set_attr(struct kvm_vcpu *vcpu, struct kvm_device_attr *attr)
 		if (!(irq_is_ppi(irq) || irq_is_spi(irq)))
 			return -EINVAL;
 
-		if (!pmu_irq_is_valid(vcpu->kvm, irq))
+		if (!pmu_irq_is_valid(kvm, irq))
 			return -EINVAL;
 
 		if (kvm_arm_pmu_irq_initialized(vcpu))
@@ -963,7 +1050,7 @@ int kvm_arm_pmu_v3_set_attr(struct kvm_vcpu *vcpu, struct kvm_device_attr *attr)
 		struct kvm_pmu_event_filter filter;
 		int nr_events;
 
-		nr_events = kvm_pmu_event_mask(vcpu->kvm) + 1;
+		nr_events = kvm_pmu_event_mask(kvm) + 1;
 
 		uaddr = (struct kvm_pmu_event_filter __user *)(long)attr->addr;
 
@@ -975,12 +1062,17 @@ int kvm_arm_pmu_v3_set_attr(struct kvm_vcpu *vcpu, struct kvm_device_attr *attr)
 		     filter.action != KVM_PMU_EVENT_DENY))
 			return -EINVAL;
 
-		mutex_lock(&vcpu->kvm->lock);
+		mutex_lock(&kvm->lock);
+
+		if (test_bit(KVM_ARCH_FLAG_HAS_RAN_ONCE, &kvm->arch.flags)) {
+			mutex_unlock(&kvm->lock);
+			return -EBUSY;
+		}
 
-		if (!vcpu->kvm->arch.pmu_filter) {
-			vcpu->kvm->arch.pmu_filter = bitmap_alloc(nr_events, GFP_KERNEL_ACCOUNT);
-			if (!vcpu->kvm->arch.pmu_filter) {
-				mutex_unlock(&vcpu->kvm->lock);
+		if (!kvm->arch.pmu_filter) {
+			kvm->arch.pmu_filter = bitmap_alloc(nr_events, GFP_KERNEL_ACCOUNT);
+			if (!kvm->arch.pmu_filter) {
+				mutex_unlock(&kvm->lock);
 				return -ENOMEM;
 			}
 
@@ -991,20 +1083,29 @@ int kvm_arm_pmu_v3_set_attr(struct kvm_vcpu *vcpu, struct kvm_device_attr *attr)
 			 * events, the default is to allow.
 			 */
 			if (filter.action == KVM_PMU_EVENT_ALLOW)
-				bitmap_zero(vcpu->kvm->arch.pmu_filter, nr_events);
+				bitmap_zero(kvm->arch.pmu_filter, nr_events);
 			else
-				bitmap_fill(vcpu->kvm->arch.pmu_filter, nr_events);
+				bitmap_fill(kvm->arch.pmu_filter, nr_events);
 		}
 
 		if (filter.action == KVM_PMU_EVENT_ALLOW)
-			bitmap_set(vcpu->kvm->arch.pmu_filter, filter.base_event, filter.nevents);
+			bitmap_set(kvm->arch.pmu_filter, filter.base_event, filter.nevents);
 		else
-			bitmap_clear(vcpu->kvm->arch.pmu_filter, filter.base_event, filter.nevents);
+			bitmap_clear(kvm->arch.pmu_filter, filter.base_event, filter.nevents);
 
-		mutex_unlock(&vcpu->kvm->lock);
+		mutex_unlock(&kvm->lock);
 
 		return 0;
 	}
+	case KVM_ARM_VCPU_PMU_V3_SET_PMU: {
+		int __user *uaddr = (int __user *)(long)attr->addr;
+		int pmu_id;
+
+		if (get_user(pmu_id, uaddr))
+			return -EFAULT;
+
+		return kvm_arm_pmu_v3_set_pmu(vcpu, pmu_id);
+	}
 	case KVM_ARM_VCPU_PMU_V3_INIT:
 		return kvm_arm_pmu_v3_init(vcpu);
 	}
@@ -1042,6 +1143,7 @@ int kvm_arm_pmu_v3_has_attr(struct kvm_vcpu *vcpu, struct kvm_device_attr *attr)
 	case KVM_ARM_VCPU_PMU_V3_IRQ:
 	case KVM_ARM_VCPU_PMU_V3_INIT:
 	case KVM_ARM_VCPU_PMU_V3_FILTER:
+	case KVM_ARM_VCPU_PMU_V3_SET_PMU:
 		if (kvm_vcpu_has_pmu(vcpu))
 			return 0;
 	}
diff --git a/arch/arm64/kvm/pmu.c b/arch/arm64/kvm/pmu.c
index 03a6c1f4a09a..7887133d15f0 100644
--- a/arch/arm64/kvm/pmu.c
+++ b/arch/arm64/kvm/pmu.c
@@ -5,7 +5,8 @@
  */
 #include <linux/kvm_host.h>
 #include <linux/perf_event.h>
-#include <asm/kvm_hyp.h>
+
+static DEFINE_PER_CPU(struct kvm_pmu_events, kvm_pmu_events);
 
 /*
  * Given the perf event attributes and system type, determine
@@ -25,21 +26,26 @@ static bool kvm_pmu_switch_needed(struct perf_event_attr *attr)
 	return (attr->exclude_host != attr->exclude_guest);
 }
 
+struct kvm_pmu_events *kvm_get_pmu_events(void)
+{
+	return this_cpu_ptr(&kvm_pmu_events);
+}
+
 /*
  * Add events to track that we may want to switch at guest entry/exit
  * time.
  */
 void kvm_set_pmu_events(u32 set, struct perf_event_attr *attr)
 {
-	struct kvm_host_data *ctx = this_cpu_ptr_hyp_sym(kvm_host_data);
+	struct kvm_pmu_events *pmu = kvm_get_pmu_events();
 
-	if (!kvm_arm_support_pmu_v3() || !ctx || !kvm_pmu_switch_needed(attr))
+	if (!kvm_arm_support_pmu_v3() || !pmu || !kvm_pmu_switch_needed(attr))
 		return;
 
 	if (!attr->exclude_host)
-		ctx->pmu_events.events_host |= set;
+		pmu->events_host |= set;
 	if (!attr->exclude_guest)
-		ctx->pmu_events.events_guest |= set;
+		pmu->events_guest |= set;
 }
 
 /*
@@ -47,13 +53,13 @@ void kvm_set_pmu_events(u32 set, struct perf_event_attr *attr)
  */
 void kvm_clr_pmu_events(u32 clr)
 {
-	struct kvm_host_data *ctx = this_cpu_ptr_hyp_sym(kvm_host_data);
+	struct kvm_pmu_events *pmu = kvm_get_pmu_events();
 
-	if (!kvm_arm_support_pmu_v3() || !ctx)
+	if (!kvm_arm_support_pmu_v3() || !pmu)
 		return;
 
-	ctx->pmu_events.events_host &= ~clr;
-	ctx->pmu_events.events_guest &= ~clr;
+	pmu->events_host &= ~clr;
+	pmu->events_guest &= ~clr;
 }
 
 #define PMEVTYPER_READ_CASE(idx)				\
@@ -169,16 +175,16 @@ static void kvm_vcpu_pmu_disable_el0(unsigned long events)
  */
 void kvm_vcpu_pmu_restore_guest(struct kvm_vcpu *vcpu)
 {
-	struct kvm_host_data *host;
+	struct kvm_pmu_events *pmu;
 	u32 events_guest, events_host;
 
 	if (!kvm_arm_support_pmu_v3() || !has_vhe())
 		return;
 
 	preempt_disable();
-	host = this_cpu_ptr_hyp_sym(kvm_host_data);
-	events_guest = host->pmu_events.events_guest;
-	events_host = host->pmu_events.events_host;
+	pmu = kvm_get_pmu_events();
+	events_guest = pmu->events_guest;
+	events_host = pmu->events_host;
 
 	kvm_vcpu_pmu_enable_el0(events_guest);
 	kvm_vcpu_pmu_disable_el0(events_host);
@@ -190,15 +196,15 @@ void kvm_vcpu_pmu_restore_guest(struct kvm_vcpu *vcpu)
  */
 void kvm_vcpu_pmu_restore_host(struct kvm_vcpu *vcpu)
 {
-	struct kvm_host_data *host;
+	struct kvm_pmu_events *pmu;
 	u32 events_guest, events_host;
 
 	if (!kvm_arm_support_pmu_v3() || !has_vhe())
 		return;
 
-	host = this_cpu_ptr_hyp_sym(kvm_host_data);
-	events_guest = host->pmu_events.events_guest;
-	events_host = host->pmu_events.events_host;
+	pmu = kvm_get_pmu_events();
+	events_guest = pmu->events_guest;
+	events_host = pmu->events_host;
 
 	kvm_vcpu_pmu_enable_el0(events_host);
 	kvm_vcpu_pmu_disable_el0(events_guest);
diff --git a/arch/arm64/kvm/psci.c b/arch/arm64/kvm/psci.c
index 74c47d420253..7fbc4c1b9df0 100644
--- a/arch/arm64/kvm/psci.c
+++ b/arch/arm64/kvm/psci.c
@@ -46,19 +46,11 @@ static unsigned long kvm_psci_vcpu_suspend(struct kvm_vcpu *vcpu)
 	 * specification (ARM DEN 0022A). This means all suspend states
 	 * for KVM will preserve the register state.
 	 */
-	kvm_vcpu_block(vcpu);
-	kvm_clear_request(KVM_REQ_UNHALT, vcpu);
+	kvm_vcpu_wfi(vcpu);
 
 	return PSCI_RET_SUCCESS;
 }
 
-static void kvm_psci_vcpu_off(struct kvm_vcpu *vcpu)
-{
-	vcpu->arch.power_off = true;
-	kvm_make_request(KVM_REQ_SLEEP, vcpu);
-	kvm_vcpu_kick(vcpu);
-}
-
 static inline bool kvm_psci_valid_affinity(struct kvm_vcpu *vcpu,
 					   unsigned long affinity)
 {
@@ -84,8 +76,8 @@ static unsigned long kvm_psci_vcpu_on(struct kvm_vcpu *source_vcpu)
 	 */
 	if (!vcpu)
 		return PSCI_RET_INVALID_PARAMS;
-	if (!vcpu->arch.power_off) {
-		if (kvm_psci_version(source_vcpu, kvm) != KVM_ARM_PSCI_0_1)
+	if (!kvm_arm_vcpu_stopped(vcpu)) {
+		if (kvm_psci_version(source_vcpu) != KVM_ARM_PSCI_0_1)
 			return PSCI_RET_ALREADY_ON;
 		else
 			return PSCI_RET_INVALID_PARAMS;
@@ -108,12 +100,12 @@ static unsigned long kvm_psci_vcpu_on(struct kvm_vcpu *source_vcpu)
 	kvm_make_request(KVM_REQ_VCPU_RESET, vcpu);
 
 	/*
-	 * Make sure the reset request is observed if the change to
-	 * power_state is observed.
+	 * Make sure the reset request is observed if the RUNNABLE mp_state is
+	 * observed.
 	 */
 	smp_wmb();
 
-	vcpu->arch.power_off = false;
+	vcpu->arch.mp_state.mp_state = KVM_MP_STATE_RUNNABLE;
 	kvm_vcpu_wake_up(vcpu);
 
 	return PSCI_RET_SUCCESS;
@@ -121,8 +113,8 @@ static unsigned long kvm_psci_vcpu_on(struct kvm_vcpu *source_vcpu)
 
 static unsigned long kvm_psci_vcpu_affinity_info(struct kvm_vcpu *vcpu)
 {
-	int i, matching_cpus = 0;
-	unsigned long mpidr;
+	int matching_cpus = 0;
+	unsigned long i, mpidr;
 	unsigned long target_affinity;
 	unsigned long target_affinity_mask;
 	unsigned long lowest_affinity_level;
@@ -151,7 +143,7 @@ static unsigned long kvm_psci_vcpu_affinity_info(struct kvm_vcpu *vcpu)
 		mpidr = kvm_vcpu_get_mpidr_aff(tmp);
 		if ((mpidr & target_affinity_mask) == target_affinity) {
 			matching_cpus++;
-			if (!tmp->arch.power_off)
+			if (!kvm_arm_vcpu_stopped(tmp))
 				return PSCI_0_2_AFFINITY_LEVEL_ON;
 		}
 	}
@@ -162,9 +154,9 @@ static unsigned long kvm_psci_vcpu_affinity_info(struct kvm_vcpu *vcpu)
 	return PSCI_0_2_AFFINITY_LEVEL_OFF;
 }
 
-static void kvm_prepare_system_event(struct kvm_vcpu *vcpu, u32 type)
+static void kvm_prepare_system_event(struct kvm_vcpu *vcpu, u32 type, u64 flags)
 {
-	int i;
+	unsigned long i;
 	struct kvm_vcpu *tmp;
 
 	/*
@@ -177,22 +169,39 @@ static void kvm_prepare_system_event(struct kvm_vcpu *vcpu, u32 type)
 	 * re-initialized.
 	 */
 	kvm_for_each_vcpu(i, tmp, vcpu->kvm)
-		tmp->arch.power_off = true;
+		tmp->arch.mp_state.mp_state = KVM_MP_STATE_STOPPED;
 	kvm_make_all_cpus_request(vcpu->kvm, KVM_REQ_SLEEP);
 
 	memset(&vcpu->run->system_event, 0, sizeof(vcpu->run->system_event));
 	vcpu->run->system_event.type = type;
+	vcpu->run->system_event.ndata = 1;
+	vcpu->run->system_event.data[0] = flags;
 	vcpu->run->exit_reason = KVM_EXIT_SYSTEM_EVENT;
 }
 
 static void kvm_psci_system_off(struct kvm_vcpu *vcpu)
 {
-	kvm_prepare_system_event(vcpu, KVM_SYSTEM_EVENT_SHUTDOWN);
+	kvm_prepare_system_event(vcpu, KVM_SYSTEM_EVENT_SHUTDOWN, 0);
 }
 
 static void kvm_psci_system_reset(struct kvm_vcpu *vcpu)
 {
-	kvm_prepare_system_event(vcpu, KVM_SYSTEM_EVENT_RESET);
+	kvm_prepare_system_event(vcpu, KVM_SYSTEM_EVENT_RESET, 0);
+}
+
+static void kvm_psci_system_reset2(struct kvm_vcpu *vcpu)
+{
+	kvm_prepare_system_event(vcpu, KVM_SYSTEM_EVENT_RESET,
+				 KVM_SYSTEM_EVENT_RESET_FLAG_PSCI_RESET2);
+}
+
+static void kvm_psci_system_suspend(struct kvm_vcpu *vcpu)
+{
+	struct kvm_run *run = vcpu->run;
+
+	memset(&run->system_event, 0, sizeof(vcpu->run->system_event));
+	run->system_event.type = KVM_SYSTEM_EVENT_SUSPEND;
+	run->exit_reason = KVM_EXIT_SYSTEM_EVENT;
 }
 
 static void kvm_psci_narrow_to_32bit(struct kvm_vcpu *vcpu)
@@ -209,15 +218,11 @@ static void kvm_psci_narrow_to_32bit(struct kvm_vcpu *vcpu)
 
 static unsigned long kvm_psci_check_allowed_function(struct kvm_vcpu *vcpu, u32 fn)
 {
-	switch(fn) {
-	case PSCI_0_2_FN64_CPU_SUSPEND:
-	case PSCI_0_2_FN64_CPU_ON:
-	case PSCI_0_2_FN64_AFFINITY_INFO:
-		/* Disallow these functions for 32bit guests */
-		if (vcpu_mode_is_32bit(vcpu))
-			return PSCI_RET_NOT_SUPPORTED;
-		break;
-	}
+	/*
+	 * Prevent 32 bit guests from calling 64 bit PSCI functions.
+	 */
+	if ((fn & PSCI_0_2_64BIT) && vcpu_mode_is_32bit(vcpu))
+		return PSCI_RET_NOT_SUPPORTED;
 
 	return 0;
 }
@@ -229,10 +234,6 @@ static int kvm_psci_0_2_call(struct kvm_vcpu *vcpu)
 	unsigned long val;
 	int ret = 1;
 
-	val = kvm_psci_check_allowed_function(vcpu, psci_fn);
-	if (val)
-		goto out;
-
 	switch (psci_fn) {
 	case PSCI_0_2_FN_PSCI_VERSION:
 		/*
@@ -246,7 +247,7 @@ static int kvm_psci_0_2_call(struct kvm_vcpu *vcpu)
 		val = kvm_psci_vcpu_suspend(vcpu);
 		break;
 	case PSCI_0_2_FN_CPU_OFF:
-		kvm_psci_vcpu_off(vcpu);
+		kvm_arm_vcpu_power_off(vcpu);
 		val = PSCI_RET_SUCCESS;
 		break;
 	case PSCI_0_2_FN_CPU_ON:
@@ -300,29 +301,31 @@ static int kvm_psci_0_2_call(struct kvm_vcpu *vcpu)
 		break;
 	}
 
-out:
 	smccc_set_retval(vcpu, val, 0, 0, 0);
 	return ret;
 }
 
-static int kvm_psci_1_0_call(struct kvm_vcpu *vcpu)
+static int kvm_psci_1_x_call(struct kvm_vcpu *vcpu, u32 minor)
 {
+	unsigned long val = PSCI_RET_NOT_SUPPORTED;
 	u32 psci_fn = smccc_get_function(vcpu);
-	u32 feature;
-	unsigned long val;
+	struct kvm *kvm = vcpu->kvm;
+	u32 arg;
 	int ret = 1;
 
 	switch(psci_fn) {
 	case PSCI_0_2_FN_PSCI_VERSION:
-		val = KVM_ARM_PSCI_1_0;
+		val = minor == 0 ? KVM_ARM_PSCI_1_0 : KVM_ARM_PSCI_1_1;
 		break;
 	case PSCI_1_0_FN_PSCI_FEATURES:
-		feature = smccc_get_arg1(vcpu);
-		val = kvm_psci_check_allowed_function(vcpu, feature);
+		arg = smccc_get_arg1(vcpu);
+		val = kvm_psci_check_allowed_function(vcpu, arg);
 		if (val)
 			break;
 
-		switch(feature) {
+		val = PSCI_RET_NOT_SUPPORTED;
+
+		switch(arg) {
 		case PSCI_0_2_FN_PSCI_VERSION:
 		case PSCI_0_2_FN_CPU_SUSPEND:
 		case PSCI_0_2_FN64_CPU_SUSPEND:
@@ -338,8 +341,47 @@ static int kvm_psci_1_0_call(struct kvm_vcpu *vcpu)
 		case ARM_SMCCC_VERSION_FUNC_ID:
 			val = 0;
 			break;
-		default:
-			val = PSCI_RET_NOT_SUPPORTED;
+		case PSCI_1_0_FN_SYSTEM_SUSPEND:
+		case PSCI_1_0_FN64_SYSTEM_SUSPEND:
+			if (test_bit(KVM_ARCH_FLAG_SYSTEM_SUSPEND_ENABLED, &kvm->arch.flags))
+				val = 0;
+			break;
+		case PSCI_1_1_FN_SYSTEM_RESET2:
+		case PSCI_1_1_FN64_SYSTEM_RESET2:
+			if (minor >= 1)
+				val = 0;
+			break;
+		}
+		break;
+	case PSCI_1_0_FN_SYSTEM_SUSPEND:
+		kvm_psci_narrow_to_32bit(vcpu);
+		fallthrough;
+	case PSCI_1_0_FN64_SYSTEM_SUSPEND:
+		/*
+		 * Return directly to userspace without changing the vCPU's
+		 * registers. Userspace depends on reading the SMCCC parameters
+		 * to implement SYSTEM_SUSPEND.
+		 */
+		if (test_bit(KVM_ARCH_FLAG_SYSTEM_SUSPEND_ENABLED, &kvm->arch.flags)) {
+			kvm_psci_system_suspend(vcpu);
+			return 0;
+		}
+		break;
+	case PSCI_1_1_FN_SYSTEM_RESET2:
+		kvm_psci_narrow_to_32bit(vcpu);
+		fallthrough;
+	case PSCI_1_1_FN64_SYSTEM_RESET2:
+		if (minor >= 1) {
+			arg = smccc_get_arg1(vcpu);
+
+			if (arg <= PSCI_1_1_RESET_TYPE_SYSTEM_WARM_RESET ||
+			    arg >= PSCI_1_1_RESET_TYPE_VENDOR_START) {
+				kvm_psci_system_reset2(vcpu);
+				vcpu_set_reg(vcpu, 0, PSCI_RET_INTERNAL_FAILURE);
+				return 0;
+			}
+
+			val = PSCI_RET_INVALID_PARAMS;
 			break;
 		}
 		break;
@@ -359,7 +401,7 @@ static int kvm_psci_0_1_call(struct kvm_vcpu *vcpu)
 
 	switch (psci_fn) {
 	case KVM_PSCI_FN_CPU_OFF:
-		kvm_psci_vcpu_off(vcpu);
+		kvm_arm_vcpu_power_off(vcpu);
 		val = PSCI_RET_SUCCESS;
 		break;
 	case KVM_PSCI_FN_CPU_ON:
@@ -392,180 +434,25 @@ static int kvm_psci_0_1_call(struct kvm_vcpu *vcpu)
  */
 int kvm_psci_call(struct kvm_vcpu *vcpu)
 {
-	switch (kvm_psci_version(vcpu, vcpu->kvm)) {
+	u32 psci_fn = smccc_get_function(vcpu);
+	unsigned long val;
+
+	val = kvm_psci_check_allowed_function(vcpu, psci_fn);
+	if (val) {
+		smccc_set_retval(vcpu, val, 0, 0, 0);
+		return 1;
+	}
+
+	switch (kvm_psci_version(vcpu)) {
+	case KVM_ARM_PSCI_1_1:
+		return kvm_psci_1_x_call(vcpu, 1);
 	case KVM_ARM_PSCI_1_0:
-		return kvm_psci_1_0_call(vcpu);
+		return kvm_psci_1_x_call(vcpu, 0);
 	case KVM_ARM_PSCI_0_2:
 		return kvm_psci_0_2_call(vcpu);
 	case KVM_ARM_PSCI_0_1:
 		return kvm_psci_0_1_call(vcpu);
 	default:
 		return -EINVAL;
-	};
-}
-
-int kvm_arm_get_fw_num_regs(struct kvm_vcpu *vcpu)
-{
-	return 3;		/* PSCI version and two workaround registers */
-}
-
-int kvm_arm_copy_fw_reg_indices(struct kvm_vcpu *vcpu, u64 __user *uindices)
-{
-	if (put_user(KVM_REG_ARM_PSCI_VERSION, uindices++))
-		return -EFAULT;
-
-	if (put_user(KVM_REG_ARM_SMCCC_ARCH_WORKAROUND_1, uindices++))
-		return -EFAULT;
-
-	if (put_user(KVM_REG_ARM_SMCCC_ARCH_WORKAROUND_2, uindices++))
-		return -EFAULT;
-
-	return 0;
-}
-
-#define KVM_REG_FEATURE_LEVEL_WIDTH	4
-#define KVM_REG_FEATURE_LEVEL_MASK	(BIT(KVM_REG_FEATURE_LEVEL_WIDTH) - 1)
-
-/*
- * Convert the workaround level into an easy-to-compare number, where higher
- * values mean better protection.
- */
-static int get_kernel_wa_level(u64 regid)
-{
-	switch (regid) {
-	case KVM_REG_ARM_SMCCC_ARCH_WORKAROUND_1:
-		switch (arm64_get_spectre_v2_state()) {
-		case SPECTRE_VULNERABLE:
-			return KVM_REG_ARM_SMCCC_ARCH_WORKAROUND_1_NOT_AVAIL;
-		case SPECTRE_MITIGATED:
-			return KVM_REG_ARM_SMCCC_ARCH_WORKAROUND_1_AVAIL;
-		case SPECTRE_UNAFFECTED:
-			return KVM_REG_ARM_SMCCC_ARCH_WORKAROUND_1_NOT_REQUIRED;
-		}
-		return KVM_REG_ARM_SMCCC_ARCH_WORKAROUND_1_NOT_AVAIL;
-	case KVM_REG_ARM_SMCCC_ARCH_WORKAROUND_2:
-		switch (arm64_get_spectre_v4_state()) {
-		case SPECTRE_MITIGATED:
-			/*
-			 * As for the hypercall discovery, we pretend we
-			 * don't have any FW mitigation if SSBS is there at
-			 * all times.
-			 */
-			if (cpus_have_final_cap(ARM64_SSBS))
-				return KVM_REG_ARM_SMCCC_ARCH_WORKAROUND_2_NOT_AVAIL;
-			fallthrough;
-		case SPECTRE_UNAFFECTED:
-			return KVM_REG_ARM_SMCCC_ARCH_WORKAROUND_2_NOT_REQUIRED;
-		case SPECTRE_VULNERABLE:
-			return KVM_REG_ARM_SMCCC_ARCH_WORKAROUND_2_NOT_AVAIL;
-		}
-	}
-
-	return -EINVAL;
-}
-
-int kvm_arm_get_fw_reg(struct kvm_vcpu *vcpu, const struct kvm_one_reg *reg)
-{
-	void __user *uaddr = (void __user *)(long)reg->addr;
-	u64 val;
-
-	switch (reg->id) {
-	case KVM_REG_ARM_PSCI_VERSION:
-		val = kvm_psci_version(vcpu, vcpu->kvm);
-		break;
-	case KVM_REG_ARM_SMCCC_ARCH_WORKAROUND_1:
-	case KVM_REG_ARM_SMCCC_ARCH_WORKAROUND_2:
-		val = get_kernel_wa_level(reg->id) & KVM_REG_FEATURE_LEVEL_MASK;
-		break;
-	default:
-		return -ENOENT;
 	}
-
-	if (copy_to_user(uaddr, &val, KVM_REG_SIZE(reg->id)))
-		return -EFAULT;
-
-	return 0;
-}
-
-int kvm_arm_set_fw_reg(struct kvm_vcpu *vcpu, const struct kvm_one_reg *reg)
-{
-	void __user *uaddr = (void __user *)(long)reg->addr;
-	u64 val;
-	int wa_level;
-
-	if (copy_from_user(&val, uaddr, KVM_REG_SIZE(reg->id)))
-		return -EFAULT;
-
-	switch (reg->id) {
-	case KVM_REG_ARM_PSCI_VERSION:
-	{
-		bool wants_02;
-
-		wants_02 = test_bit(KVM_ARM_VCPU_PSCI_0_2, vcpu->arch.features);
-
-		switch (val) {
-		case KVM_ARM_PSCI_0_1:
-			if (wants_02)
-				return -EINVAL;
-			vcpu->kvm->arch.psci_version = val;
-			return 0;
-		case KVM_ARM_PSCI_0_2:
-		case KVM_ARM_PSCI_1_0:
-			if (!wants_02)
-				return -EINVAL;
-			vcpu->kvm->arch.psci_version = val;
-			return 0;
-		}
-		break;
-	}
-
-	case KVM_REG_ARM_SMCCC_ARCH_WORKAROUND_1:
-		if (val & ~KVM_REG_FEATURE_LEVEL_MASK)
-			return -EINVAL;
-
-		if (get_kernel_wa_level(reg->id) < val)
-			return -EINVAL;
-
-		return 0;
-
-	case KVM_REG_ARM_SMCCC_ARCH_WORKAROUND_2:
-		if (val & ~(KVM_REG_FEATURE_LEVEL_MASK |
-			    KVM_REG_ARM_SMCCC_ARCH_WORKAROUND_2_ENABLED))
-			return -EINVAL;
-
-		/* The enabled bit must not be set unless the level is AVAIL. */
-		if ((val & KVM_REG_ARM_SMCCC_ARCH_WORKAROUND_2_ENABLED) &&
-		    (val & KVM_REG_FEATURE_LEVEL_MASK) != KVM_REG_ARM_SMCCC_ARCH_WORKAROUND_2_AVAIL)
-			return -EINVAL;
-
-		/*
-		 * Map all the possible incoming states to the only two we
-		 * really want to deal with.
-		 */
-		switch (val & KVM_REG_FEATURE_LEVEL_MASK) {
-		case KVM_REG_ARM_SMCCC_ARCH_WORKAROUND_2_NOT_AVAIL:
-		case KVM_REG_ARM_SMCCC_ARCH_WORKAROUND_2_UNKNOWN:
-			wa_level = KVM_REG_ARM_SMCCC_ARCH_WORKAROUND_2_NOT_AVAIL;
-			break;
-		case KVM_REG_ARM_SMCCC_ARCH_WORKAROUND_2_AVAIL:
-		case KVM_REG_ARM_SMCCC_ARCH_WORKAROUND_2_NOT_REQUIRED:
-			wa_level = KVM_REG_ARM_SMCCC_ARCH_WORKAROUND_2_NOT_REQUIRED;
-			break;
-		default:
-			return -EINVAL;
-		}
-
-		/*
-		 * We can deal with NOT_AVAIL on NOT_REQUIRED, but not the
-		 * other way around.
-		 */
-		if (get_kernel_wa_level(reg->id) < wa_level)
-			return -EINVAL;
-
-		return 0;
-	default:
-		return -ENOENT;
-	}
-
-	return -EINVAL;
 }
diff --git a/arch/arm64/kvm/reset.c b/arch/arm64/kvm/reset.c
index 426bd7fbc3fd..5ae18472205a 100644
--- a/arch/arm64/kvm/reset.c
+++ b/arch/arm64/kvm/reset.c
@@ -52,10 +52,10 @@ int kvm_arm_init_sve(void)
 		 * The get_sve_reg()/set_sve_reg() ioctl interface will need
 		 * to be extended with multiple register slice support in
 		 * order to support vector lengths greater than
-		 * SVE_VL_ARCH_MAX:
+		 * VL_ARCH_MAX:
 		 */
-		if (WARN_ON(kvm_sve_max_vl > SVE_VL_ARCH_MAX))
-			kvm_sve_max_vl = SVE_VL_ARCH_MAX;
+		if (WARN_ON(kvm_sve_max_vl > VL_ARCH_MAX))
+			kvm_sve_max_vl = VL_ARCH_MAX;
 
 		/*
 		 * Don't even try to make use of vector lengths that
@@ -81,7 +81,7 @@ static int kvm_vcpu_enable_sve(struct kvm_vcpu *vcpu)
 	 * KVM_REG_ARM64_SVE_VLS.  Allocation is deferred until
 	 * kvm_arm_vcpu_finalize(), which freezes the configuration.
 	 */
-	vcpu->arch.flags |= KVM_ARM64_GUEST_HAS_SVE;
+	vcpu_set_flag(vcpu, GUEST_HAS_SVE);
 
 	return 0;
 }
@@ -94,24 +94,33 @@ static int kvm_vcpu_finalize_sve(struct kvm_vcpu *vcpu)
 {
 	void *buf;
 	unsigned int vl;
+	size_t reg_sz;
+	int ret;
 
 	vl = vcpu->arch.sve_max_vl;
 
 	/*
 	 * Responsibility for these properties is shared between
-	 * kvm_arm_init_arch_resources(), kvm_vcpu_enable_sve() and
+	 * kvm_arm_init_sve(), kvm_vcpu_enable_sve() and
 	 * set_sve_vls().  Double-check here just to be sure:
 	 */
 	if (WARN_ON(!sve_vl_valid(vl) || vl > sve_max_virtualisable_vl() ||
-		    vl > SVE_VL_ARCH_MAX))
+		    vl > VL_ARCH_MAX))
 		return -EIO;
 
-	buf = kzalloc(SVE_SIG_REGS_SIZE(sve_vq_from_vl(vl)), GFP_KERNEL_ACCOUNT);
+	reg_sz = vcpu_sve_state_size(vcpu);
+	buf = kzalloc(reg_sz, GFP_KERNEL_ACCOUNT);
 	if (!buf)
 		return -ENOMEM;
 
+	ret = kvm_share_hyp(buf, buf + reg_sz);
+	if (ret) {
+		kfree(buf);
+		return ret;
+	}
+	
 	vcpu->arch.sve_state = buf;
-	vcpu->arch.flags |= KVM_ARM64_VCPU_SVE_FINALIZED;
+	vcpu_set_flag(vcpu, VCPU_SVE_FINALIZED);
 	return 0;
 }
 
@@ -141,7 +150,13 @@ bool kvm_arm_vcpu_is_finalized(struct kvm_vcpu *vcpu)
 
 void kvm_arm_vcpu_destroy(struct kvm_vcpu *vcpu)
 {
-	kfree(vcpu->arch.sve_state);
+	void *sve_state = vcpu->arch.sve_state;
+
+	kvm_vcpu_unshare_task_fp(vcpu);
+	kvm_unshare_hyp(vcpu, vcpu + 1);
+	if (sve_state)
+		kvm_unshare_hyp(sve_state, sve_state + vcpu_sve_state_size(vcpu));
+	kfree(sve_state);
 }
 
 static void kvm_vcpu_reset_sve(struct kvm_vcpu *vcpu)
@@ -162,41 +177,64 @@ static int kvm_vcpu_enable_ptrauth(struct kvm_vcpu *vcpu)
 	    !system_has_full_ptr_auth())
 		return -EINVAL;
 
-	vcpu->arch.flags |= KVM_ARM64_GUEST_HAS_PTRAUTH;
+	vcpu_set_flag(vcpu, GUEST_HAS_PTRAUTH);
 	return 0;
 }
 
-static bool vcpu_allowed_register_width(struct kvm_vcpu *vcpu)
+/**
+ * kvm_set_vm_width() - set the register width for the guest
+ * @vcpu: Pointer to the vcpu being configured
+ *
+ * Set both KVM_ARCH_FLAG_EL1_32BIT and KVM_ARCH_FLAG_REG_WIDTH_CONFIGURED
+ * in the VM flags based on the vcpu's requested register width, the HW
+ * capabilities and other options (such as MTE).
+ * When REG_WIDTH_CONFIGURED is already set, the vcpu settings must be
+ * consistent with the value of the FLAG_EL1_32BIT bit in the flags.
+ *
+ * Return: 0 on success, negative error code on failure.
+ */
+static int kvm_set_vm_width(struct kvm_vcpu *vcpu)
 {
-	struct kvm_vcpu *tmp;
+	struct kvm *kvm = vcpu->kvm;
 	bool is32bit;
-	int i;
 
 	is32bit = vcpu_has_feature(vcpu, KVM_ARM_VCPU_EL1_32BIT);
+
+	lockdep_assert_held(&kvm->lock);
+
+	if (test_bit(KVM_ARCH_FLAG_REG_WIDTH_CONFIGURED, &kvm->arch.flags)) {
+		/*
+		 * The guest's register width is already configured.
+		 * Make sure that the vcpu is consistent with it.
+		 */
+		if (is32bit == test_bit(KVM_ARCH_FLAG_EL1_32BIT, &kvm->arch.flags))
+			return 0;
+
+		return -EINVAL;
+	}
+
 	if (!cpus_have_const_cap(ARM64_HAS_32BIT_EL1) && is32bit)
-		return false;
+		return -EINVAL;
 
 	/* MTE is incompatible with AArch32 */
-	if (kvm_has_mte(vcpu->kvm) && is32bit)
-		return false;
+	if (kvm_has_mte(kvm) && is32bit)
+		return -EINVAL;
 
-	/* Check that the vcpus are either all 32bit or all 64bit */
-	kvm_for_each_vcpu(i, tmp, vcpu->kvm) {
-		if (vcpu_has_feature(tmp, KVM_ARM_VCPU_EL1_32BIT) != is32bit)
-			return false;
-	}
+	if (is32bit)
+		set_bit(KVM_ARCH_FLAG_EL1_32BIT, &kvm->arch.flags);
 
-	return true;
+	set_bit(KVM_ARCH_FLAG_REG_WIDTH_CONFIGURED, &kvm->arch.flags);
+
+	return 0;
 }
 
 /**
  * kvm_reset_vcpu - sets core registers and sys_regs to reset value
  * @vcpu: The VCPU pointer
  *
- * This function finds the right table above and sets the registers on
- * the virtual CPU struct to their architecturally defined reset
- * values, except for registers whose reset is deferred until
- * kvm_arm_vcpu_finalize().
+ * This function sets the registers on the virtual CPU struct to their
+ * architecturally defined reset values, except for registers whose reset is
+ * deferred until kvm_arm_vcpu_finalize().
  *
  * Note: This function can be called from two paths: The KVM_ARM_VCPU_INIT
  * ioctl or as part of handling a request issued by another VCPU in the PSCI
@@ -216,10 +254,16 @@ int kvm_reset_vcpu(struct kvm_vcpu *vcpu)
 	u32 pstate;
 
 	mutex_lock(&vcpu->kvm->lock);
-	reset_state = vcpu->arch.reset_state;
-	WRITE_ONCE(vcpu->arch.reset_state.reset, false);
+	ret = kvm_set_vm_width(vcpu);
+	if (!ret) {
+		reset_state = vcpu->arch.reset_state;
+		WRITE_ONCE(vcpu->arch.reset_state.reset, false);
+	}
 	mutex_unlock(&vcpu->kvm->lock);
 
+	if (ret)
+		return ret;
+
 	/* Reset PMU outside of the non-preemptible section */
 	kvm_pmu_vcpu_reset(vcpu);
 
@@ -246,14 +290,9 @@ int kvm_reset_vcpu(struct kvm_vcpu *vcpu)
 		}
 	}
 
-	if (!vcpu_allowed_register_width(vcpu)) {
-		ret = -EINVAL;
-		goto out;
-	}
-
 	switch (vcpu->arch.target) {
 	default:
-		if (test_bit(KVM_ARM_VCPU_EL1_32BIT, vcpu->arch.features)) {
+		if (vcpu_el1_is_32bit(vcpu)) {
 			pstate = VCPU_RESET_PSTATE_SVC;
 		} else {
 			pstate = VCPU_RESET_PSTATE_EL1;
@@ -320,7 +359,7 @@ int kvm_set_ipa_limit(void)
 
 	mmfr0 = read_sanitised_ftr_reg(SYS_ID_AA64MMFR0_EL1);
 	parange = cpuid_feature_extract_unsigned_field(mmfr0,
-				ID_AA64MMFR0_PARANGE_SHIFT);
+				ID_AA64MMFR0_EL1_PARANGE_SHIFT);
 	/*
 	 * IPA size beyond 48 bits could not be supported
 	 * on either 4K or 16K page size. Hence let's cap
@@ -328,20 +367,20 @@ int kvm_set_ipa_limit(void)
 	 * on the system.
 	 */
 	if (PAGE_SIZE != SZ_64K)
-		parange = min(parange, (unsigned int)ID_AA64MMFR0_PARANGE_48);
+		parange = min(parange, (unsigned int)ID_AA64MMFR0_EL1_PARANGE_48);
 
 	/*
 	 * Check with ARMv8.5-GTG that our PAGE_SIZE is supported at
 	 * Stage-2. If not, things will stop very quickly.
 	 */
-	switch (cpuid_feature_extract_unsigned_field(mmfr0, ID_AA64MMFR0_TGRAN_2_SHIFT)) {
-	case ID_AA64MMFR0_TGRAN_2_SUPPORTED_NONE:
+	switch (cpuid_feature_extract_unsigned_field(mmfr0, ID_AA64MMFR0_EL1_TGRAN_2_SHIFT)) {
+	case ID_AA64MMFR0_EL1_TGRAN_2_SUPPORTED_NONE:
 		kvm_err("PAGE_SIZE not supported at Stage-2, giving up\n");
 		return -EINVAL;
-	case ID_AA64MMFR0_TGRAN_2_SUPPORTED_DEFAULT:
+	case ID_AA64MMFR0_EL1_TGRAN_2_SUPPORTED_DEFAULT:
 		kvm_debug("PAGE_SIZE supported at Stage-2 (default)\n");
 		break;
-	case ID_AA64MMFR0_TGRAN_2_SUPPORTED_MIN ... ID_AA64MMFR0_TGRAN_2_SUPPORTED_MAX:
+	case ID_AA64MMFR0_EL1_TGRAN_2_SUPPORTED_MIN ... ID_AA64MMFR0_EL1_TGRAN_2_SUPPORTED_MAX:
 		kvm_debug("PAGE_SIZE supported at Stage-2 (advertised)\n");
 		break;
 	default:
diff --git a/arch/arm64/kvm/stacktrace.c b/arch/arm64/kvm/stacktrace.c
new file mode 100644
index 000000000000..3ace5b75813b
--- /dev/null
+++ b/arch/arm64/kvm/stacktrace.c
@@ -0,0 +1,245 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * KVM nVHE hypervisor stack tracing support.
+ *
+ * The unwinder implementation depends on the nVHE mode:
+ *
+ *   1) Non-protected nVHE mode - the host can directly access the
+ *      HYP stack pages and unwind the HYP stack in EL1. This saves having
+ *      to allocate shared buffers for the host to read the unwinded
+ *      stacktrace.
+ *
+ *   2) pKVM (protected nVHE) mode - the host cannot directly access
+ *      the HYP memory. The stack is unwinded in EL2 and dumped to a shared
+ *      buffer where the host can read and print the stacktrace.
+ *
+ * Copyright (C) 2022 Google LLC
+ */
+
+#include <linux/kvm.h>
+#include <linux/kvm_host.h>
+
+#include <asm/stacktrace/nvhe.h>
+
+static struct stack_info stackinfo_get_overflow(void)
+{
+	struct kvm_nvhe_stacktrace_info *stacktrace_info
+				= this_cpu_ptr_nvhe_sym(kvm_stacktrace_info);
+	unsigned long low = (unsigned long)stacktrace_info->overflow_stack_base;
+	unsigned long high = low + OVERFLOW_STACK_SIZE;
+
+	return (struct stack_info) {
+		.low = low,
+		.high = high,
+	};
+}
+
+static struct stack_info stackinfo_get_overflow_kern_va(void)
+{
+	unsigned long low = (unsigned long)this_cpu_ptr_nvhe_sym(overflow_stack);
+	unsigned long high = low + OVERFLOW_STACK_SIZE;
+
+	return (struct stack_info) {
+		.low = low,
+		.high = high,
+	};
+}
+
+static struct stack_info stackinfo_get_hyp(void)
+{
+	struct kvm_nvhe_stacktrace_info *stacktrace_info
+				= this_cpu_ptr_nvhe_sym(kvm_stacktrace_info);
+	unsigned long low = (unsigned long)stacktrace_info->stack_base;
+	unsigned long high = low + PAGE_SIZE;
+
+	return (struct stack_info) {
+		.low = low,
+		.high = high,
+	};
+}
+
+static struct stack_info stackinfo_get_hyp_kern_va(void)
+{
+	unsigned long low = (unsigned long)*this_cpu_ptr(&kvm_arm_hyp_stack_page);
+	unsigned long high = low + PAGE_SIZE;
+
+	return (struct stack_info) {
+		.low = low,
+		.high = high,
+	};
+}
+
+/*
+ * kvm_nvhe_stack_kern_va - Convert KVM nVHE HYP stack addresses to a kernel VAs
+ *
+ * The nVHE hypervisor stack is mapped in the flexible 'private' VA range, to
+ * allow for guard pages below the stack. Consequently, the fixed offset address
+ * translation macros won't work here.
+ *
+ * The kernel VA is calculated as an offset from the kernel VA of the hypervisor
+ * stack base.
+ *
+ * Returns true on success and updates @addr to its corresponding kernel VA;
+ * otherwise returns false.
+ */
+static bool kvm_nvhe_stack_kern_va(unsigned long *addr, unsigned long size)
+{
+	struct stack_info stack_hyp, stack_kern;
+
+	stack_hyp = stackinfo_get_hyp();
+	stack_kern = stackinfo_get_hyp_kern_va();
+	if (stackinfo_on_stack(&stack_hyp, *addr, size))
+		goto found;
+
+	stack_hyp = stackinfo_get_overflow();
+	stack_kern = stackinfo_get_overflow_kern_va();
+	if (stackinfo_on_stack(&stack_hyp, *addr, size))
+		goto found;
+
+	return false;
+
+found:
+	*addr = *addr - stack_hyp.low + stack_kern.low;
+	return true;
+}
+
+/*
+ * Convert a KVN nVHE HYP frame record address to a kernel VA
+ */
+static bool kvm_nvhe_stack_kern_record_va(unsigned long *addr)
+{
+	return kvm_nvhe_stack_kern_va(addr, 16);
+}
+
+static int unwind_next(struct unwind_state *state)
+{
+	/*
+	 * The FP is in the hypervisor VA space. Convert it to the kernel VA
+	 * space so it can be unwound by the regular unwind functions.
+	 */
+	if (!kvm_nvhe_stack_kern_record_va(&state->fp))
+		return -EINVAL;
+
+	return unwind_next_frame_record(state);
+}
+
+static void unwind(struct unwind_state *state,
+		   stack_trace_consume_fn consume_entry, void *cookie)
+{
+	while (1) {
+		int ret;
+
+		if (!consume_entry(cookie, state->pc))
+			break;
+		ret = unwind_next(state);
+		if (ret < 0)
+			break;
+	}
+}
+
+/*
+ * kvm_nvhe_dump_backtrace_entry - Symbolize and print an nVHE backtrace entry
+ *
+ * @arg    : the hypervisor offset, used for address translation
+ * @where  : the program counter corresponding to the stack frame
+ */
+static bool kvm_nvhe_dump_backtrace_entry(void *arg, unsigned long where)
+{
+	unsigned long va_mask = GENMASK_ULL(vabits_actual - 1, 0);
+	unsigned long hyp_offset = (unsigned long)arg;
+
+	/* Mask tags and convert to kern addr */
+	where = (where & va_mask) + hyp_offset;
+	kvm_err(" [<%016lx>] %pB\n", where, (void *)(where + kaslr_offset()));
+
+	return true;
+}
+
+static void kvm_nvhe_dump_backtrace_start(void)
+{
+	kvm_err("nVHE call trace:\n");
+}
+
+static void kvm_nvhe_dump_backtrace_end(void)
+{
+	kvm_err("---[ end nVHE call trace ]---\n");
+}
+
+/*
+ * hyp_dump_backtrace - Dump the non-protected nVHE backtrace.
+ *
+ * @hyp_offset: hypervisor offset, used for address translation.
+ *
+ * The host can directly access HYP stack pages in non-protected
+ * mode, so the unwinding is done directly from EL1. This removes
+ * the need for shared buffers between host and hypervisor for
+ * the stacktrace.
+ */
+static void hyp_dump_backtrace(unsigned long hyp_offset)
+{
+	struct kvm_nvhe_stacktrace_info *stacktrace_info;
+	struct stack_info stacks[] = {
+		stackinfo_get_overflow_kern_va(),
+		stackinfo_get_hyp_kern_va(),
+	};
+	struct unwind_state state = {
+		.stacks = stacks,
+		.nr_stacks = ARRAY_SIZE(stacks),
+	};
+
+	stacktrace_info = this_cpu_ptr_nvhe_sym(kvm_stacktrace_info);
+
+	kvm_nvhe_unwind_init(&state, stacktrace_info->fp, stacktrace_info->pc);
+
+	kvm_nvhe_dump_backtrace_start();
+	unwind(&state, kvm_nvhe_dump_backtrace_entry, (void *)hyp_offset);
+	kvm_nvhe_dump_backtrace_end();
+}
+
+#ifdef CONFIG_PROTECTED_NVHE_STACKTRACE
+DECLARE_KVM_NVHE_PER_CPU(unsigned long [NVHE_STACKTRACE_SIZE/sizeof(long)],
+			 pkvm_stacktrace);
+
+/*
+ * pkvm_dump_backtrace - Dump the protected nVHE HYP backtrace.
+ *
+ * @hyp_offset: hypervisor offset, used for address translation.
+ *
+ * Dumping of the pKVM HYP backtrace is done by reading the
+ * stack addresses from the shared stacktrace buffer, since the
+ * host cannot directly access hypervisor memory in protected
+ * mode.
+ */
+static void pkvm_dump_backtrace(unsigned long hyp_offset)
+{
+	unsigned long *stacktrace
+		= (unsigned long *) this_cpu_ptr_nvhe_sym(pkvm_stacktrace);
+	int i;
+
+	kvm_nvhe_dump_backtrace_start();
+	/* The saved stacktrace is terminated by a null entry */
+	for (i = 0;
+	     i < ARRAY_SIZE(kvm_nvhe_sym(pkvm_stacktrace)) && stacktrace[i];
+	     i++)
+		kvm_nvhe_dump_backtrace_entry((void *)hyp_offset, stacktrace[i]);
+	kvm_nvhe_dump_backtrace_end();
+}
+#else	/* !CONFIG_PROTECTED_NVHE_STACKTRACE */
+static void pkvm_dump_backtrace(unsigned long hyp_offset)
+{
+	kvm_err("Cannot dump pKVM nVHE stacktrace: !CONFIG_PROTECTED_NVHE_STACKTRACE\n");
+}
+#endif /* CONFIG_PROTECTED_NVHE_STACKTRACE */
+
+/*
+ * kvm_nvhe_dump_backtrace - Dump KVM nVHE hypervisor backtrace.
+ *
+ * @hyp_offset: hypervisor offset, used for address translation.
+ */
+void kvm_nvhe_dump_backtrace(unsigned long hyp_offset)
+{
+	if (is_protected_kvm_enabled())
+		pkvm_dump_backtrace(hyp_offset);
+	else
+		hyp_dump_backtrace(hyp_offset);
+}
diff --git a/arch/arm64/kvm/sys_regs.c b/arch/arm64/kvm/sys_regs.c
index e3ec1a44f94d..f4a7c5abcbca 100644
--- a/arch/arm64/kvm/sys_regs.c
+++ b/arch/arm64/kvm/sys_regs.c
@@ -34,16 +34,13 @@
 #include "trace.h"
 
 /*
- * All of this file is extremely similar to the ARM coproc.c, but the
- * types are different. My gut feeling is that it should be pretty
- * easy to merge, but that would be an ABI breakage -- again. VFP
- * would also need to be abstracted.
- *
  * For AArch32, we only take care of what is being trapped. Anything
  * that has to do with init and userspace access has to go via the
  * 64bit interface.
  */
 
+static u64 sys_reg_to_index(const struct sys_reg_desc *reg);
+
 static bool read_from_write_only(struct kvm_vcpu *vcpu,
 				 struct sys_reg_params *params,
 				 const struct sys_reg_desc *r)
@@ -68,7 +65,7 @@ u64 vcpu_read_sys_reg(const struct kvm_vcpu *vcpu, int reg)
 {
 	u64 val = 0x8badf00d8badf00d;
 
-	if (vcpu->arch.sysregs_loaded_on_cpu &&
+	if (vcpu_get_flag(vcpu, SYSREGS_ON_CPU) &&
 	    __vcpu_read_sys_reg_from_cpu(reg, &val))
 		return val;
 
@@ -77,7 +74,7 @@ u64 vcpu_read_sys_reg(const struct kvm_vcpu *vcpu, int reg)
 
 void vcpu_write_sys_reg(struct kvm_vcpu *vcpu, u64 val, int reg)
 {
-	if (vcpu->arch.sysregs_loaded_on_cpu &&
+	if (vcpu_get_flag(vcpu, SYSREGS_ON_CPU) &&
 	    __vcpu_write_sys_reg_to_cpu(val, reg))
 		return;
 
@@ -276,7 +273,7 @@ static bool trap_loregion(struct kvm_vcpu *vcpu,
 	u64 val = read_sanitised_ftr_reg(SYS_ID_AA64MMFR1_EL1);
 	u32 sr = reg_to_encoding(r);
 
-	if (!(val & (0xfUL << ID_AA64MMFR1_LOR_SHIFT))) {
+	if (!(val & (0xfUL << ID_AA64MMFR1_EL1_LO_SHIFT))) {
 		kvm_inject_undefined(vcpu);
 		return false;
 	}
@@ -287,16 +284,47 @@ static bool trap_loregion(struct kvm_vcpu *vcpu,
 	return trap_raz_wi(vcpu, p, r);
 }
 
+static bool trap_oslar_el1(struct kvm_vcpu *vcpu,
+			   struct sys_reg_params *p,
+			   const struct sys_reg_desc *r)
+{
+	u64 oslsr;
+
+	if (!p->is_write)
+		return read_from_write_only(vcpu, p, r);
+
+	/* Forward the OSLK bit to OSLSR */
+	oslsr = __vcpu_sys_reg(vcpu, OSLSR_EL1) & ~SYS_OSLSR_OSLK;
+	if (p->regval & SYS_OSLAR_OSLK)
+		oslsr |= SYS_OSLSR_OSLK;
+
+	__vcpu_sys_reg(vcpu, OSLSR_EL1) = oslsr;
+	return true;
+}
+
 static bool trap_oslsr_el1(struct kvm_vcpu *vcpu,
 			   struct sys_reg_params *p,
 			   const struct sys_reg_desc *r)
 {
-	if (p->is_write) {
-		return ignore_write(vcpu, p);
-	} else {
-		p->regval = (1 << 3);
-		return true;
-	}
+	if (p->is_write)
+		return write_to_read_only(vcpu, p, r);
+
+	p->regval = __vcpu_sys_reg(vcpu, r->reg);
+	return true;
+}
+
+static int set_oslsr_el1(struct kvm_vcpu *vcpu, const struct sys_reg_desc *rd,
+			 u64 val)
+{
+	/*
+	 * The only modifiable bit is the OSLK bit. Refuse the write if
+	 * userspace attempts to change any other bit in the register.
+	 */
+	if ((val ^ rd->val) & ~SYS_OSLSR_OSLK)
+		return -EINVAL;
+
+	__vcpu_sys_reg(vcpu, rd->reg) = val;
+	return 0;
 }
 
 static bool trap_dbgauthstatus_el1(struct kvm_vcpu *vcpu,
@@ -344,7 +372,7 @@ static bool trap_debug_regs(struct kvm_vcpu *vcpu,
 {
 	if (p->is_write) {
 		vcpu_write_sys_reg(vcpu, p->regval, r->reg);
-		vcpu->arch.flags |= KVM_ARM64_DEBUG_DIRTY;
+		vcpu_set_flag(vcpu, DEBUG_DIRTY);
 	} else {
 		p->regval = vcpu_read_sys_reg(vcpu, r->reg);
 	}
@@ -360,8 +388,8 @@ static bool trap_debug_regs(struct kvm_vcpu *vcpu,
  * A 32 bit write to a debug register leave top bits alone
  * A 32 bit read from a debug register only returns the bottom bits
  *
- * All writes will set the KVM_ARM64_DEBUG_DIRTY flag to ensure the
- * hyp.S code switches between host and guest values in future.
+ * All writes will set the DEBUG_DIRTY flag to ensure the hyp code
+ * switches between host and guest values in future.
  */
 static void reg_to_dbg(struct kvm_vcpu *vcpu,
 		       struct sys_reg_params *p,
@@ -377,7 +405,7 @@ static void reg_to_dbg(struct kvm_vcpu *vcpu,
 	val |= (p->regval & (mask >> shift)) << shift;
 	*dbg_reg = val;
 
-	vcpu->arch.flags |= KVM_ARM64_DEBUG_DIRTY;
+	vcpu_set_flag(vcpu, DEBUG_DIRTY);
 }
 
 static void dbg_to_reg(struct kvm_vcpu *vcpu,
@@ -408,22 +436,16 @@ static bool trap_bvr(struct kvm_vcpu *vcpu,
 }
 
 static int set_bvr(struct kvm_vcpu *vcpu, const struct sys_reg_desc *rd,
-		const struct kvm_one_reg *reg, void __user *uaddr)
+		   u64 val)
 {
-	__u64 *r = &vcpu->arch.vcpu_debug_state.dbg_bvr[rd->CRm];
-
-	if (copy_from_user(r, uaddr, KVM_REG_SIZE(reg->id)) != 0)
-		return -EFAULT;
+	vcpu->arch.vcpu_debug_state.dbg_bvr[rd->CRm] = val;
 	return 0;
 }
 
 static int get_bvr(struct kvm_vcpu *vcpu, const struct sys_reg_desc *rd,
-	const struct kvm_one_reg *reg, void __user *uaddr)
+		   u64 *val)
 {
-	__u64 *r = &vcpu->arch.vcpu_debug_state.dbg_bvr[rd->CRm];
-
-	if (copy_to_user(uaddr, r, KVM_REG_SIZE(reg->id)) != 0)
-		return -EFAULT;
+	*val = vcpu->arch.vcpu_debug_state.dbg_bvr[rd->CRm];
 	return 0;
 }
 
@@ -450,23 +472,16 @@ static bool trap_bcr(struct kvm_vcpu *vcpu,
 }
 
 static int set_bcr(struct kvm_vcpu *vcpu, const struct sys_reg_desc *rd,
-		const struct kvm_one_reg *reg, void __user *uaddr)
+		   u64 val)
 {
-	__u64 *r = &vcpu->arch.vcpu_debug_state.dbg_bcr[rd->CRm];
-
-	if (copy_from_user(r, uaddr, KVM_REG_SIZE(reg->id)) != 0)
-		return -EFAULT;
-
+	vcpu->arch.vcpu_debug_state.dbg_bcr[rd->CRm] = val;
 	return 0;
 }
 
 static int get_bcr(struct kvm_vcpu *vcpu, const struct sys_reg_desc *rd,
-	const struct kvm_one_reg *reg, void __user *uaddr)
+		   u64 *val)
 {
-	__u64 *r = &vcpu->arch.vcpu_debug_state.dbg_bcr[rd->CRm];
-
-	if (copy_to_user(uaddr, r, KVM_REG_SIZE(reg->id)) != 0)
-		return -EFAULT;
+	*val = vcpu->arch.vcpu_debug_state.dbg_bcr[rd->CRm];
 	return 0;
 }
 
@@ -494,22 +509,16 @@ static bool trap_wvr(struct kvm_vcpu *vcpu,
 }
 
 static int set_wvr(struct kvm_vcpu *vcpu, const struct sys_reg_desc *rd,
-		const struct kvm_one_reg *reg, void __user *uaddr)
+		   u64 val)
 {
-	__u64 *r = &vcpu->arch.vcpu_debug_state.dbg_wvr[rd->CRm];
-
-	if (copy_from_user(r, uaddr, KVM_REG_SIZE(reg->id)) != 0)
-		return -EFAULT;
+	vcpu->arch.vcpu_debug_state.dbg_wvr[rd->CRm] = val;
 	return 0;
 }
 
 static int get_wvr(struct kvm_vcpu *vcpu, const struct sys_reg_desc *rd,
-	const struct kvm_one_reg *reg, void __user *uaddr)
+		   u64 *val)
 {
-	__u64 *r = &vcpu->arch.vcpu_debug_state.dbg_wvr[rd->CRm];
-
-	if (copy_to_user(uaddr, r, KVM_REG_SIZE(reg->id)) != 0)
-		return -EFAULT;
+	*val = vcpu->arch.vcpu_debug_state.dbg_wvr[rd->CRm];
 	return 0;
 }
 
@@ -536,22 +545,16 @@ static bool trap_wcr(struct kvm_vcpu *vcpu,
 }
 
 static int set_wcr(struct kvm_vcpu *vcpu, const struct sys_reg_desc *rd,
-		const struct kvm_one_reg *reg, void __user *uaddr)
+		   u64 val)
 {
-	__u64 *r = &vcpu->arch.vcpu_debug_state.dbg_wcr[rd->CRm];
-
-	if (copy_from_user(r, uaddr, KVM_REG_SIZE(reg->id)) != 0)
-		return -EFAULT;
+	vcpu->arch.vcpu_debug_state.dbg_wcr[rd->CRm] = val;
 	return 0;
 }
 
 static int get_wcr(struct kvm_vcpu *vcpu, const struct sys_reg_desc *rd,
-	const struct kvm_one_reg *reg, void __user *uaddr)
+		   u64 *val)
 {
-	__u64 *r = &vcpu->arch.vcpu_debug_state.dbg_wcr[rd->CRm];
-
-	if (copy_to_user(uaddr, r, KVM_REG_SIZE(reg->id)) != 0)
-		return -EFAULT;
+	*val = vcpu->arch.vcpu_debug_state.dbg_wcr[rd->CRm];
 	return 0;
 }
 
@@ -649,7 +652,7 @@ static void reset_pmcr(struct kvm_vcpu *vcpu, const struct sys_reg_desc *r)
 	 */
 	val = ((pmcr & ~ARMV8_PMU_PMCR_MASK)
 	       | (ARMV8_PMU_PMCR_MASK & 0xdecafbad)) & (~ARMV8_PMU_PMCR_E);
-	if (!system_supports_32bit_el0())
+	if (!kvm_supports_32bit_el0())
 		val |= ARMV8_PMU_PMCR_LC;
 	__vcpu_sys_reg(vcpu, r->reg) = val;
 }
@@ -698,7 +701,7 @@ static bool access_pmcr(struct kvm_vcpu *vcpu, struct sys_reg_params *p,
 		val = __vcpu_sys_reg(vcpu, PMCR_EL0);
 		val &= ~ARMV8_PMU_PMCR_MASK;
 		val |= p->regval & ARMV8_PMU_PMCR_MASK;
-		if (!system_supports_32bit_el0())
+		if (!kvm_supports_32bit_el0())
 			val |= ARMV8_PMU_PMCR_LC;
 		__vcpu_sys_reg(vcpu, PMCR_EL0) = val;
 		kvm_pmu_handle_pmcr(vcpu, val);
@@ -1060,13 +1063,12 @@ static bool access_arch_timer(struct kvm_vcpu *vcpu,
 }
 
 /* Read a sanitised cpufeature ID register by sys_reg_desc */
-static u64 read_id_reg(const struct kvm_vcpu *vcpu,
-		struct sys_reg_desc const *r, bool raz)
+static u64 read_id_reg(const struct kvm_vcpu *vcpu, struct sys_reg_desc const *r)
 {
 	u32 id = reg_to_encoding(r);
 	u64 val;
 
-	if (raz)
+	if (sysreg_visible_as_raz(vcpu, r))
 		return 0;
 
 	val = read_sanitised_ftr_reg(id);
@@ -1074,39 +1076,47 @@ static u64 read_id_reg(const struct kvm_vcpu *vcpu,
 	switch (id) {
 	case SYS_ID_AA64PFR0_EL1:
 		if (!vcpu_has_sve(vcpu))
-			val &= ~ARM64_FEATURE_MASK(ID_AA64PFR0_SVE);
-		val &= ~ARM64_FEATURE_MASK(ID_AA64PFR0_AMU);
-		val &= ~ARM64_FEATURE_MASK(ID_AA64PFR0_CSV2);
-		val |= FIELD_PREP(ARM64_FEATURE_MASK(ID_AA64PFR0_CSV2), (u64)vcpu->kvm->arch.pfr0_csv2);
-		val &= ~ARM64_FEATURE_MASK(ID_AA64PFR0_CSV3);
-		val |= FIELD_PREP(ARM64_FEATURE_MASK(ID_AA64PFR0_CSV3), (u64)vcpu->kvm->arch.pfr0_csv3);
-		if (irqchip_in_kernel(vcpu->kvm) &&
-		    vcpu->kvm->arch.vgic.vgic_model == KVM_DEV_TYPE_ARM_VGIC_V3) {
-			val &= ~ARM64_FEATURE_MASK(ID_AA64PFR0_GIC);
-			val |= FIELD_PREP(ARM64_FEATURE_MASK(ID_AA64PFR0_GIC), 1);
+			val &= ~ARM64_FEATURE_MASK(ID_AA64PFR0_EL1_SVE);
+		val &= ~ARM64_FEATURE_MASK(ID_AA64PFR0_EL1_AMU);
+		val &= ~ARM64_FEATURE_MASK(ID_AA64PFR0_EL1_CSV2);
+		val |= FIELD_PREP(ARM64_FEATURE_MASK(ID_AA64PFR0_EL1_CSV2), (u64)vcpu->kvm->arch.pfr0_csv2);
+		val &= ~ARM64_FEATURE_MASK(ID_AA64PFR0_EL1_CSV3);
+		val |= FIELD_PREP(ARM64_FEATURE_MASK(ID_AA64PFR0_EL1_CSV3), (u64)vcpu->kvm->arch.pfr0_csv3);
+		if (kvm_vgic_global_state.type == VGIC_V3) {
+			val &= ~ARM64_FEATURE_MASK(ID_AA64PFR0_EL1_GIC);
+			val |= FIELD_PREP(ARM64_FEATURE_MASK(ID_AA64PFR0_EL1_GIC), 1);
 		}
 		break;
 	case SYS_ID_AA64PFR1_EL1:
 		if (!kvm_has_mte(vcpu->kvm))
-			val &= ~ARM64_FEATURE_MASK(ID_AA64PFR1_MTE);
+			val &= ~ARM64_FEATURE_MASK(ID_AA64PFR1_EL1_MTE);
+
+		val &= ~ARM64_FEATURE_MASK(ID_AA64PFR1_EL1_SME);
 		break;
 	case SYS_ID_AA64ISAR1_EL1:
 		if (!vcpu_has_ptrauth(vcpu))
-			val &= ~(ARM64_FEATURE_MASK(ID_AA64ISAR1_APA) |
-				 ARM64_FEATURE_MASK(ID_AA64ISAR1_API) |
-				 ARM64_FEATURE_MASK(ID_AA64ISAR1_GPA) |
-				 ARM64_FEATURE_MASK(ID_AA64ISAR1_GPI));
+			val &= ~(ARM64_FEATURE_MASK(ID_AA64ISAR1_EL1_APA) |
+				 ARM64_FEATURE_MASK(ID_AA64ISAR1_EL1_API) |
+				 ARM64_FEATURE_MASK(ID_AA64ISAR1_EL1_GPA) |
+				 ARM64_FEATURE_MASK(ID_AA64ISAR1_EL1_GPI));
+		break;
+	case SYS_ID_AA64ISAR2_EL1:
+		if (!vcpu_has_ptrauth(vcpu))
+			val &= ~(ARM64_FEATURE_MASK(ID_AA64ISAR2_EL1_APA3) |
+				 ARM64_FEATURE_MASK(ID_AA64ISAR2_EL1_GPA3));
+		if (!cpus_have_final_cap(ARM64_HAS_WFXT))
+			val &= ~ARM64_FEATURE_MASK(ID_AA64ISAR2_EL1_WFxT);
 		break;
 	case SYS_ID_AA64DFR0_EL1:
 		/* Limit debug to ARMv8.0 */
-		val &= ~ARM64_FEATURE_MASK(ID_AA64DFR0_DEBUGVER);
-		val |= FIELD_PREP(ARM64_FEATURE_MASK(ID_AA64DFR0_DEBUGVER), 6);
+		val &= ~ARM64_FEATURE_MASK(ID_AA64DFR0_EL1_DebugVer);
+		val |= FIELD_PREP(ARM64_FEATURE_MASK(ID_AA64DFR0_EL1_DebugVer), 6);
 		/* Limit guests to PMUv3 for ARMv8.4 */
 		val = cpuid_feature_cap_perfmon_field(val,
-						      ID_AA64DFR0_PMUVER_SHIFT,
-						      kvm_vcpu_has_pmu(vcpu) ? ID_AA64DFR0_PMUVER_8_4 : 0);
+						      ID_AA64DFR0_EL1_PMUVer_SHIFT,
+						      kvm_vcpu_has_pmu(vcpu) ? ID_AA64DFR0_EL1_PMUVer_V3P4 : 0);
 		/* Hide SPE from guests */
-		val &= ~ARM64_FEATURE_MASK(ID_AA64DFR0_PMSVER);
+		val &= ~ARM64_FEATURE_MASK(ID_AA64DFR0_EL1_PMSVer);
 		break;
 	case SYS_ID_DFR0_EL1:
 		/* Limit guests to PMUv3 for ARMv8.4 */
@@ -1134,40 +1144,39 @@ static unsigned int id_visibility(const struct kvm_vcpu *vcpu,
 	return 0;
 }
 
-/* cpufeature ID register access trap handlers */
-
-static bool __access_id_reg(struct kvm_vcpu *vcpu,
-			    struct sys_reg_params *p,
-			    const struct sys_reg_desc *r,
-			    bool raz)
+static unsigned int aa32_id_visibility(const struct kvm_vcpu *vcpu,
+				       const struct sys_reg_desc *r)
 {
-	if (p->is_write)
-		return write_to_read_only(vcpu, p, r);
+	/*
+	 * AArch32 ID registers are UNKNOWN if AArch32 isn't implemented at any
+	 * EL. Promote to RAZ/WI in order to guarantee consistency between
+	 * systems.
+	 */
+	if (!kvm_supports_32bit_el0())
+		return REG_RAZ | REG_USER_WI;
 
-	p->regval = read_id_reg(vcpu, r, raz);
-	return true;
+	return id_visibility(vcpu, r);
 }
 
+static unsigned int raz_visibility(const struct kvm_vcpu *vcpu,
+				   const struct sys_reg_desc *r)
+{
+	return REG_RAZ;
+}
+
+/* cpufeature ID register access trap handlers */
+
 static bool access_id_reg(struct kvm_vcpu *vcpu,
 			  struct sys_reg_params *p,
 			  const struct sys_reg_desc *r)
 {
-	bool raz = sysreg_visible_as_raz(vcpu, r);
-
-	return __access_id_reg(vcpu, p, r, raz);
-}
+	if (p->is_write)
+		return write_to_read_only(vcpu, p, r);
 
-static bool access_raz_id_reg(struct kvm_vcpu *vcpu,
-			      struct sys_reg_params *p,
-			      const struct sys_reg_desc *r)
-{
-	return __access_id_reg(vcpu, p, r, true);
+	p->regval = read_id_reg(vcpu, r);
+	return true;
 }
 
-static int reg_from_user(u64 *val, const void __user *uaddr, u64 id);
-static int reg_to_user(void __user *uaddr, const u64 *val, u64 id);
-static u64 sys_reg_to_index(const struct sys_reg_desc *reg);
-
 /* Visibility overrides for SVE-specific control registers */
 static unsigned int sve_visibility(const struct kvm_vcpu *vcpu,
 				   const struct sys_reg_desc *rd)
@@ -1180,42 +1189,35 @@ static unsigned int sve_visibility(const struct kvm_vcpu *vcpu,
 
 static int set_id_aa64pfr0_el1(struct kvm_vcpu *vcpu,
 			       const struct sys_reg_desc *rd,
-			       const struct kvm_one_reg *reg, void __user *uaddr)
+			       u64 val)
 {
-	const u64 id = sys_reg_to_index(rd);
 	u8 csv2, csv3;
-	int err;
-	u64 val;
-
-	err = reg_from_user(&val, uaddr, id);
-	if (err)
-		return err;
 
 	/*
 	 * Allow AA64PFR0_EL1.CSV2 to be set from userspace as long as
 	 * it doesn't promise more than what is actually provided (the
 	 * guest could otherwise be covered in ectoplasmic residue).
 	 */
-	csv2 = cpuid_feature_extract_unsigned_field(val, ID_AA64PFR0_CSV2_SHIFT);
+	csv2 = cpuid_feature_extract_unsigned_field(val, ID_AA64PFR0_EL1_CSV2_SHIFT);
 	if (csv2 > 1 ||
 	    (csv2 && arm64_get_spectre_v2_state() != SPECTRE_UNAFFECTED))
 		return -EINVAL;
 
 	/* Same thing for CSV3 */
-	csv3 = cpuid_feature_extract_unsigned_field(val, ID_AA64PFR0_CSV3_SHIFT);
+	csv3 = cpuid_feature_extract_unsigned_field(val, ID_AA64PFR0_EL1_CSV3_SHIFT);
 	if (csv3 > 1 ||
 	    (csv3 && arm64_get_meltdown_state() != SPECTRE_UNAFFECTED))
 		return -EINVAL;
 
 	/* We can only differ with CSV[23], and anything else is an error */
-	val ^= read_id_reg(vcpu, rd, false);
-	val &= ~((0xFUL << ID_AA64PFR0_CSV2_SHIFT) |
-		 (0xFUL << ID_AA64PFR0_CSV3_SHIFT));
+	val ^= read_id_reg(vcpu, rd);
+	val &= ~(ARM64_FEATURE_MASK(ID_AA64PFR0_EL1_CSV2) |
+		 ARM64_FEATURE_MASK(ID_AA64PFR0_EL1_CSV3));
 	if (val)
 		return -EINVAL;
 
 	vcpu->kvm->arch.pfr0_csv2 = csv2;
-	vcpu->kvm->arch.pfr0_csv3 = csv3 ;
+	vcpu->kvm->arch.pfr0_csv3 = csv3;
 
 	return 0;
 }
@@ -1227,77 +1229,33 @@ static int set_id_aa64pfr0_el1(struct kvm_vcpu *vcpu,
  * are stored, and for set_id_reg() we don't allow the effective value
  * to be changed.
  */
-static int __get_id_reg(const struct kvm_vcpu *vcpu,
-			const struct sys_reg_desc *rd, void __user *uaddr,
-			bool raz)
+static int get_id_reg(struct kvm_vcpu *vcpu, const struct sys_reg_desc *rd,
+		      u64 *val)
 {
-	const u64 id = sys_reg_to_index(rd);
-	const u64 val = read_id_reg(vcpu, rd, raz);
-
-	return reg_to_user(uaddr, &val, id);
+	*val = read_id_reg(vcpu, rd);
+	return 0;
 }
 
-static int __set_id_reg(const struct kvm_vcpu *vcpu,
-			const struct sys_reg_desc *rd, void __user *uaddr,
-			bool raz)
+static int set_id_reg(struct kvm_vcpu *vcpu, const struct sys_reg_desc *rd,
+		      u64 val)
 {
-	const u64 id = sys_reg_to_index(rd);
-	int err;
-	u64 val;
-
-	err = reg_from_user(&val, uaddr, id);
-	if (err)
-		return err;
-
 	/* This is what we mean by invariant: you can't change it. */
-	if (val != read_id_reg(vcpu, rd, raz))
+	if (val != read_id_reg(vcpu, rd))
 		return -EINVAL;
 
 	return 0;
 }
 
-static int get_id_reg(struct kvm_vcpu *vcpu, const struct sys_reg_desc *rd,
-		      const struct kvm_one_reg *reg, void __user *uaddr)
-{
-	bool raz = sysreg_visible_as_raz(vcpu, rd);
-
-	return __get_id_reg(vcpu, rd, uaddr, raz);
-}
-
-static int set_id_reg(struct kvm_vcpu *vcpu, const struct sys_reg_desc *rd,
-		      const struct kvm_one_reg *reg, void __user *uaddr)
-{
-	bool raz = sysreg_visible_as_raz(vcpu, rd);
-
-	return __set_id_reg(vcpu, rd, uaddr, raz);
-}
-
-static int set_raz_id_reg(struct kvm_vcpu *vcpu, const struct sys_reg_desc *rd,
-			  const struct kvm_one_reg *reg, void __user *uaddr)
-{
-	return __set_id_reg(vcpu, rd, uaddr, true);
-}
-
 static int get_raz_reg(struct kvm_vcpu *vcpu, const struct sys_reg_desc *rd,
-		       const struct kvm_one_reg *reg, void __user *uaddr)
+		       u64 *val)
 {
-	const u64 id = sys_reg_to_index(rd);
-	const u64 val = 0;
-
-	return reg_to_user(uaddr, &val, id);
+	*val = 0;
+	return 0;
 }
 
 static int set_wi_reg(struct kvm_vcpu *vcpu, const struct sys_reg_desc *rd,
-		      const struct kvm_one_reg *reg, void __user *uaddr)
+		      u64 val)
 {
-	int err;
-	u64 val;
-
-	/* Perform the access even if we are going to ignore the value */
-	err = reg_from_user(&val, uaddr, sys_reg_to_index(rd));
-	if (err)
-		return err;
-
 	return 0;
 }
 
@@ -1387,6 +1345,15 @@ static unsigned int mte_visibility(const struct kvm_vcpu *vcpu,
 	.visibility = id_visibility,		\
 }
 
+/* sys_reg_desc initialiser for known cpufeature ID registers */
+#define AA32_ID_SANITISED(name) {		\
+	SYS_DESC(SYS_##name),			\
+	.access	= access_id_reg,		\
+	.get_user = get_id_reg,			\
+	.set_user = set_id_reg,			\
+	.visibility = aa32_id_visibility,	\
+}
+
 /*
  * sys_reg_desc initialiser for architecturally unallocated cpufeature ID
  * register with encoding Op0=3, Op1=0, CRn=0, CRm=crm, Op2=op2
@@ -1394,9 +1361,10 @@ static unsigned int mte_visibility(const struct kvm_vcpu *vcpu,
  */
 #define ID_UNALLOCATED(crm, op2) {			\
 	Op0(3), Op1(0), CRn(0), CRm(crm), Op2(op2),	\
-	.access = access_raz_id_reg,			\
-	.get_user = get_raz_reg,			\
-	.set_user = set_raz_id_reg,			\
+	.access = access_id_reg,			\
+	.get_user = get_id_reg,				\
+	.set_user = set_id_reg,				\
+	.visibility = raz_visibility			\
 }
 
 /*
@@ -1406,9 +1374,10 @@ static unsigned int mte_visibility(const struct kvm_vcpu *vcpu,
  */
 #define ID_HIDDEN(name) {			\
 	SYS_DESC(SYS_##name),			\
-	.access = access_raz_id_reg,		\
-	.get_user = get_raz_reg,		\
-	.set_user = set_raz_id_reg,		\
+	.access = access_id_reg,		\
+	.get_user = get_id_reg,			\
+	.set_user = set_id_reg,			\
+	.visibility = raz_visibility,		\
 }
 
 /*
@@ -1418,9 +1387,9 @@ static unsigned int mte_visibility(const struct kvm_vcpu *vcpu,
  * Debug handling: We do trap most, if not all debug related system
  * registers. The implementation is good enough to ensure that a guest
  * can use these with minimal performance degradation. The drawback is
- * that we don't implement any of the external debug, none of the
- * OSlock protocol. This should be revisited if we ever encounter a
- * more demanding guest...
+ * that we don't implement any of the external debug architecture.
+ * This should be revisited if we ever encounter a more demanding
+ * guest...
  */
 static const struct sys_reg_desc sys_reg_descs[] = {
 	{ SYS_DESC(SYS_DC_ISW), access_dcsw },
@@ -1447,8 +1416,9 @@ static const struct sys_reg_desc sys_reg_descs[] = {
 	DBG_BCR_BVR_WCR_WVR_EL1(15),
 
 	{ SYS_DESC(SYS_MDRAR_EL1), trap_raz_wi },
-	{ SYS_DESC(SYS_OSLAR_EL1), trap_raz_wi },
-	{ SYS_DESC(SYS_OSLSR_EL1), trap_oslsr_el1 },
+	{ SYS_DESC(SYS_OSLAR_EL1), trap_oslar_el1 },
+	{ SYS_DESC(SYS_OSLSR_EL1), trap_oslsr_el1, reset_val, OSLSR_EL1,
+		SYS_OSLSR_OSLM_IMPLEMENTED, .set_user = set_oslsr_el1, },
 	{ SYS_DESC(SYS_OSDLR_EL1), trap_raz_wi },
 	{ SYS_DESC(SYS_DBGPRCR_EL1), trap_raz_wi },
 	{ SYS_DESC(SYS_DBGCLAIMSET_EL1), trap_raz_wi },
@@ -1471,33 +1441,33 @@ static const struct sys_reg_desc sys_reg_descs[] = {
 
 	/* AArch64 mappings of the AArch32 ID registers */
 	/* CRm=1 */
-	ID_SANITISED(ID_PFR0_EL1),
-	ID_SANITISED(ID_PFR1_EL1),
-	ID_SANITISED(ID_DFR0_EL1),
+	AA32_ID_SANITISED(ID_PFR0_EL1),
+	AA32_ID_SANITISED(ID_PFR1_EL1),
+	AA32_ID_SANITISED(ID_DFR0_EL1),
 	ID_HIDDEN(ID_AFR0_EL1),
-	ID_SANITISED(ID_MMFR0_EL1),
-	ID_SANITISED(ID_MMFR1_EL1),
-	ID_SANITISED(ID_MMFR2_EL1),
-	ID_SANITISED(ID_MMFR3_EL1),
+	AA32_ID_SANITISED(ID_MMFR0_EL1),
+	AA32_ID_SANITISED(ID_MMFR1_EL1),
+	AA32_ID_SANITISED(ID_MMFR2_EL1),
+	AA32_ID_SANITISED(ID_MMFR3_EL1),
 
 	/* CRm=2 */
-	ID_SANITISED(ID_ISAR0_EL1),
-	ID_SANITISED(ID_ISAR1_EL1),
-	ID_SANITISED(ID_ISAR2_EL1),
-	ID_SANITISED(ID_ISAR3_EL1),
-	ID_SANITISED(ID_ISAR4_EL1),
-	ID_SANITISED(ID_ISAR5_EL1),
-	ID_SANITISED(ID_MMFR4_EL1),
-	ID_SANITISED(ID_ISAR6_EL1),
+	AA32_ID_SANITISED(ID_ISAR0_EL1),
+	AA32_ID_SANITISED(ID_ISAR1_EL1),
+	AA32_ID_SANITISED(ID_ISAR2_EL1),
+	AA32_ID_SANITISED(ID_ISAR3_EL1),
+	AA32_ID_SANITISED(ID_ISAR4_EL1),
+	AA32_ID_SANITISED(ID_ISAR5_EL1),
+	AA32_ID_SANITISED(ID_MMFR4_EL1),
+	AA32_ID_SANITISED(ID_ISAR6_EL1),
 
 	/* CRm=3 */
-	ID_SANITISED(MVFR0_EL1),
-	ID_SANITISED(MVFR1_EL1),
-	ID_SANITISED(MVFR2_EL1),
+	AA32_ID_SANITISED(MVFR0_EL1),
+	AA32_ID_SANITISED(MVFR1_EL1),
+	AA32_ID_SANITISED(MVFR2_EL1),
 	ID_UNALLOCATED(3,3),
-	ID_SANITISED(ID_PFR2_EL1),
+	AA32_ID_SANITISED(ID_PFR2_EL1),
 	ID_HIDDEN(ID_DFR1_EL1),
-	ID_SANITISED(ID_MMFR5_EL1),
+	AA32_ID_SANITISED(ID_MMFR5_EL1),
 	ID_UNALLOCATED(3,7),
 
 	/* AArch64 ID registers */
@@ -1508,7 +1478,7 @@ static const struct sys_reg_desc sys_reg_descs[] = {
 	ID_UNALLOCATED(4,2),
 	ID_UNALLOCATED(4,3),
 	ID_SANITISED(ID_AA64ZFR0_EL1),
-	ID_UNALLOCATED(4,5),
+	ID_HIDDEN(ID_AA64SMFR0_EL1),
 	ID_UNALLOCATED(4,6),
 	ID_UNALLOCATED(4,7),
 
@@ -1525,7 +1495,7 @@ static const struct sys_reg_desc sys_reg_descs[] = {
 	/* CRm=6 */
 	ID_SANITISED(ID_AA64ISAR0_EL1),
 	ID_SANITISED(ID_AA64ISAR1_EL1),
-	ID_UNALLOCATED(6,2),
+	ID_SANITISED(ID_AA64ISAR2_EL1),
 	ID_UNALLOCATED(6,3),
 	ID_UNALLOCATED(6,4),
 	ID_UNALLOCATED(6,5),
@@ -1551,6 +1521,8 @@ static const struct sys_reg_desc sys_reg_descs[] = {
 
 	{ SYS_DESC(SYS_ZCR_EL1), NULL, reset_val, ZCR_EL1, 0, .visibility = sve_visibility },
 	{ SYS_DESC(SYS_TRFCR_EL1), undef_access },
+	{ SYS_DESC(SYS_SMPRI_EL1), undef_access },
+	{ SYS_DESC(SYS_SMCR_EL1), undef_access },
 	{ SYS_DESC(SYS_TTBR0_EL1), access_vm_reg, reset_unknown, TTBR0_EL1 },
 	{ SYS_DESC(SYS_TTBR1_EL1), access_vm_reg, reset_unknown, TTBR1_EL1 },
 	{ SYS_DESC(SYS_TCR_EL1), access_vm_reg, reset_val, TCR_EL1, 0 },
@@ -1633,8 +1605,10 @@ static const struct sys_reg_desc sys_reg_descs[] = {
 
 	{ SYS_DESC(SYS_CCSIDR_EL1), access_ccsidr },
 	{ SYS_DESC(SYS_CLIDR_EL1), access_clidr },
+	{ SYS_DESC(SYS_SMIDR_EL1), undef_access },
 	{ SYS_DESC(SYS_CSSELR_EL1), access_csselr, reset_unknown, CSSELR_EL1 },
 	{ SYS_DESC(SYS_CTR_EL0), access_ctr },
+	{ SYS_DESC(SYS_SVCR), undef_access },
 
 	{ PMU_SYS_REG(SYS_PMCR_EL0), .access = access_pmcr,
 	  .reset = reset_pmcr, .reg = PMCR_EL0 },
@@ -1674,6 +1648,7 @@ static const struct sys_reg_desc sys_reg_descs[] = {
 
 	{ SYS_DESC(SYS_TPIDR_EL0), NULL, reset_unknown, TPIDR_EL0 },
 	{ SYS_DESC(SYS_TPIDRRO_EL0), NULL, reset_unknown, TPIDRRO_EL0 },
+	{ SYS_DESC(SYS_TPIDR2_EL0), undef_access },
 
 	{ SYS_DESC(SYS_SCXTNUM_EL0), undef_access },
 
@@ -1839,11 +1814,11 @@ static bool trap_dbgdidr(struct kvm_vcpu *vcpu,
 	} else {
 		u64 dfr = read_sanitised_ftr_reg(SYS_ID_AA64DFR0_EL1);
 		u64 pfr = read_sanitised_ftr_reg(SYS_ID_AA64PFR0_EL1);
-		u32 el3 = !!cpuid_feature_extract_unsigned_field(pfr, ID_AA64PFR0_EL3_SHIFT);
+		u32 el3 = !!cpuid_feature_extract_unsigned_field(pfr, ID_AA64PFR0_EL1_EL3_SHIFT);
 
-		p->regval = ((((dfr >> ID_AA64DFR0_WRPS_SHIFT) & 0xf) << 28) |
-			     (((dfr >> ID_AA64DFR0_BRPS_SHIFT) & 0xf) << 24) |
-			     (((dfr >> ID_AA64DFR0_CTX_CMPS_SHIFT) & 0xf) << 20)
+		p->regval = ((((dfr >> ID_AA64DFR0_EL1_WRPs_SHIFT) & 0xf) << 28) |
+			     (((dfr >> ID_AA64DFR0_EL1_BRPs_SHIFT) & 0xf) << 24) |
+			     (((dfr >> ID_AA64DFR0_EL1_CTX_CMPs_SHIFT) & 0xf) << 20)
 			     | (6 << 16) | (1 << 15) | (el3 << 14) | (el3 << 12));
 		return true;
 	}
@@ -1920,10 +1895,10 @@ static const struct sys_reg_desc cp14_regs[] = {
 
 	DBGBXVR(0),
 	/* DBGOSLAR */
-	{ Op1( 0), CRn( 1), CRm( 0), Op2( 4), trap_raz_wi },
+	{ Op1( 0), CRn( 1), CRm( 0), Op2( 4), trap_oslar_el1 },
 	DBGBXVR(1),
 	/* DBGOSLSR */
-	{ Op1( 0), CRn( 1), CRm( 1), Op2( 4), trap_oslsr_el1 },
+	{ Op1( 0), CRn( 1), CRm( 1), Op2( 4), trap_oslsr_el1, NULL, OSLSR_EL1 },
 	DBGBXVR(2),
 	DBGBXVR(3),
 	/* DBGOSDLR */
@@ -1969,20 +1944,22 @@ static const struct sys_reg_desc cp14_64_regs[] = {
 	{ Op1( 0), CRm( 2), .access = trap_raz_wi },
 };
 
+#define CP15_PMU_SYS_REG(_map, _Op1, _CRn, _CRm, _Op2)			\
+	AA32(_map),							\
+	Op1(_Op1), CRn(_CRn), CRm(_CRm), Op2(_Op2),			\
+	.visibility = pmu_visibility
+
 /* Macro to expand the PMEVCNTRn register */
 #define PMU_PMEVCNTR(n)							\
-	/* PMEVCNTRn */							\
-	{ Op1(0), CRn(0b1110),						\
-	  CRm((0b1000 | (((n) >> 3) & 0x3))), Op2(((n) & 0x7)),		\
-	  access_pmu_evcntr }
+	{ CP15_PMU_SYS_REG(DIRECT, 0, 0b1110,				\
+	  (0b1000 | (((n) >> 3) & 0x3)), ((n) & 0x7)),			\
+	  .access = access_pmu_evcntr }
 
 /* Macro to expand the PMEVTYPERn register */
 #define PMU_PMEVTYPER(n)						\
-	/* PMEVTYPERn */						\
-	{ Op1(0), CRn(0b1110),						\
-	  CRm((0b1100 | (((n) >> 3) & 0x3))), Op2(((n) & 0x7)),		\
-	  access_pmu_evtyper }
-
+	{ CP15_PMU_SYS_REG(DIRECT, 0, 0b1110,				\
+	  (0b1100 | (((n) >> 3) & 0x3)), ((n) & 0x7)),			\
+	  .access = access_pmu_evtyper }
 /*
  * Trapped cp15 registers. TTBR0/TTBR1 get a double encoding,
  * depending on the way they are accessed (as a 32bit or a 64bit
@@ -2022,25 +1999,25 @@ static const struct sys_reg_desc cp15_regs[] = {
 	{ Op1( 0), CRn( 7), CRm(14), Op2( 2), access_dcsw },
 
 	/* PMU */
-	{ Op1( 0), CRn( 9), CRm(12), Op2( 0), access_pmcr },
-	{ Op1( 0), CRn( 9), CRm(12), Op2( 1), access_pmcnten },
-	{ Op1( 0), CRn( 9), CRm(12), Op2( 2), access_pmcnten },
-	{ Op1( 0), CRn( 9), CRm(12), Op2( 3), access_pmovs },
-	{ Op1( 0), CRn( 9), CRm(12), Op2( 4), access_pmswinc },
-	{ Op1( 0), CRn( 9), CRm(12), Op2( 5), access_pmselr },
-	{ AA32(LO), Op1( 0), CRn( 9), CRm(12), Op2( 6), access_pmceid },
-	{ AA32(LO), Op1( 0), CRn( 9), CRm(12), Op2( 7), access_pmceid },
-	{ Op1( 0), CRn( 9), CRm(13), Op2( 0), access_pmu_evcntr },
-	{ Op1( 0), CRn( 9), CRm(13), Op2( 1), access_pmu_evtyper },
-	{ Op1( 0), CRn( 9), CRm(13), Op2( 2), access_pmu_evcntr },
-	{ Op1( 0), CRn( 9), CRm(14), Op2( 0), access_pmuserenr },
-	{ Op1( 0), CRn( 9), CRm(14), Op2( 1), access_pminten },
-	{ Op1( 0), CRn( 9), CRm(14), Op2( 2), access_pminten },
-	{ Op1( 0), CRn( 9), CRm(14), Op2( 3), access_pmovs },
-	{ AA32(HI), Op1( 0), CRn( 9), CRm(14), Op2( 4), access_pmceid },
-	{ AA32(HI), Op1( 0), CRn( 9), CRm(14), Op2( 5), access_pmceid },
+	{ CP15_PMU_SYS_REG(DIRECT, 0, 9, 12, 0), .access = access_pmcr },
+	{ CP15_PMU_SYS_REG(DIRECT, 0, 9, 12, 1), .access = access_pmcnten },
+	{ CP15_PMU_SYS_REG(DIRECT, 0, 9, 12, 2), .access = access_pmcnten },
+	{ CP15_PMU_SYS_REG(DIRECT, 0, 9, 12, 3), .access = access_pmovs },
+	{ CP15_PMU_SYS_REG(DIRECT, 0, 9, 12, 4), .access = access_pmswinc },
+	{ CP15_PMU_SYS_REG(DIRECT, 0, 9, 12, 5), .access = access_pmselr },
+	{ CP15_PMU_SYS_REG(LO,     0, 9, 12, 6), .access = access_pmceid },
+	{ CP15_PMU_SYS_REG(LO,     0, 9, 12, 7), .access = access_pmceid },
+	{ CP15_PMU_SYS_REG(DIRECT, 0, 9, 13, 0), .access = access_pmu_evcntr },
+	{ CP15_PMU_SYS_REG(DIRECT, 0, 9, 13, 1), .access = access_pmu_evtyper },
+	{ CP15_PMU_SYS_REG(DIRECT, 0, 9, 13, 2), .access = access_pmu_evcntr },
+	{ CP15_PMU_SYS_REG(DIRECT, 0, 9, 14, 0), .access = access_pmuserenr },
+	{ CP15_PMU_SYS_REG(DIRECT, 0, 9, 14, 1), .access = access_pminten },
+	{ CP15_PMU_SYS_REG(DIRECT, 0, 9, 14, 2), .access = access_pminten },
+	{ CP15_PMU_SYS_REG(DIRECT, 0, 9, 14, 3), .access = access_pmovs },
+	{ CP15_PMU_SYS_REG(HI,     0, 9, 14, 4), .access = access_pmceid },
+	{ CP15_PMU_SYS_REG(HI,     0, 9, 14, 5), .access = access_pmceid },
 	/* PMMIR */
-	{ Op1( 0), CRn( 9), CRm(14), Op2( 6), trap_raz_wi },
+	{ CP15_PMU_SYS_REG(DIRECT, 0, 9, 14, 6), .access = trap_raz_wi },
 
 	/* PRRR/MAIR0 */
 	{ AA32(LO), Op1( 0), CRn(10), CRm( 2), Op2( 0), access_vm_reg, NULL, MAIR_EL1 },
@@ -2125,7 +2102,7 @@ static const struct sys_reg_desc cp15_regs[] = {
 	PMU_PMEVTYPER(29),
 	PMU_PMEVTYPER(30),
 	/* PMCCFILTR */
-	{ Op1(0), CRn(14), CRm(15), Op2(7), access_pmu_evtyper },
+	{ CP15_PMU_SYS_REG(DIRECT, 0, 14, 15, 7), .access = access_pmu_evtyper },
 
 	{ Op1(1), CRn( 0), CRm( 0), Op2(0), access_ccsidr },
 	{ Op1(1), CRn( 0), CRm( 0), Op2(1), access_clidr },
@@ -2134,7 +2111,7 @@ static const struct sys_reg_desc cp15_regs[] = {
 
 static const struct sys_reg_desc cp15_64_regs[] = {
 	{ Op1( 0), CRn( 0), CRm( 2), Op2( 0), access_vm_reg, NULL, TTBR0_EL1 },
-	{ Op1( 0), CRn( 0), CRm( 9), Op2( 0), access_pmu_evcntr },
+	{ CP15_PMU_SYS_REG(DIRECT, 0, 0, 9, 0), .access = access_pmu_evcntr },
 	{ Op1( 0), CRn( 0), CRm(12), Op2( 0), access_gic_sgi }, /* ICC_SGI1R */
 	{ Op1( 1), CRn( 0), CRm( 2), Op2( 0), access_vm_reg, NULL, TTBR1_EL1 },
 	{ Op1( 1), CRn( 0), CRm(12), Op2( 0), access_gic_sgi }, /* ICC_ASGI1R */
@@ -2142,25 +2119,24 @@ static const struct sys_reg_desc cp15_64_regs[] = {
 	{ SYS_DESC(SYS_AARCH32_CNTP_CVAL),    access_arch_timer },
 };
 
-static int check_sysreg_table(const struct sys_reg_desc *table, unsigned int n,
-			      bool is_32)
+static bool check_sysreg_table(const struct sys_reg_desc *table, unsigned int n,
+			       bool is_32)
 {
 	unsigned int i;
 
 	for (i = 0; i < n; i++) {
 		if (!is_32 && table[i].reg && !table[i].reset) {
-			kvm_err("sys_reg table %p entry %d has lacks reset\n",
-				table, i);
-			return 1;
+			kvm_err("sys_reg table %pS entry %d lacks reset\n", &table[i], i);
+			return false;
 		}
 
 		if (i && cmp_sys_reg(&table[i-1], &table[i]) >= 0) {
-			kvm_err("sys_reg table %p out of order (%d)\n", table, i - 1);
-			return 1;
+			kvm_err("sys_reg table %pS entry %d out of order\n", &table[i - 1], i - 1);
+			return false;
 		}
 	}
 
-	return 0;
+	return true;
 }
 
 int kvm_handle_cp14_load_store(struct kvm_vcpu *vcpu)
@@ -2201,27 +2177,27 @@ static void perform_access(struct kvm_vcpu *vcpu,
  * @table: array of trap descriptors
  * @num: size of the trap descriptor array
  *
- * Return 0 if the access has been handled, and -1 if not.
+ * Return true if the access has been handled, false if not.
  */
-static int emulate_cp(struct kvm_vcpu *vcpu,
-		      struct sys_reg_params *params,
-		      const struct sys_reg_desc *table,
-		      size_t num)
+static bool emulate_cp(struct kvm_vcpu *vcpu,
+		       struct sys_reg_params *params,
+		       const struct sys_reg_desc *table,
+		       size_t num)
 {
 	const struct sys_reg_desc *r;
 
 	if (!table)
-		return -1;	/* Not handled */
+		return false;	/* Not handled */
 
 	r = find_reg(params, table, num);
 
 	if (r) {
 		perform_access(vcpu, params, r);
-		return 0;
+		return true;
 	}
 
 	/* Not handled */
-	return -1;
+	return false;
 }
 
 static void unhandled_cp_access(struct kvm_vcpu *vcpu,
@@ -2259,7 +2235,7 @@ static int kvm_handle_cp_64(struct kvm_vcpu *vcpu,
 			    size_t nr_global)
 {
 	struct sys_reg_params params;
-	u32 esr = kvm_vcpu_get_esr(vcpu);
+	u64 esr = kvm_vcpu_get_esr(vcpu);
 	int Rt = kvm_vcpu_sys_get_rt(vcpu);
 	int Rt2 = (esr >> 10) & 0x1f;
 
@@ -2285,7 +2261,7 @@ static int kvm_handle_cp_64(struct kvm_vcpu *vcpu,
 	 * potential register operation in the case of a read and return
 	 * with success.
 	 */
-	if (!emulate_cp(vcpu, &params, global, nr_global)) {
+	if (emulate_cp(vcpu, &params, global, nr_global)) {
 		/* Split up the value between registers for the read side */
 		if (!params.is_write) {
 			vcpu_set_reg(vcpu, Rt, lower_32_bits(params.regval));
@@ -2299,34 +2275,144 @@ static int kvm_handle_cp_64(struct kvm_vcpu *vcpu,
 	return 1;
 }
 
+static bool emulate_sys_reg(struct kvm_vcpu *vcpu, struct sys_reg_params *params);
+
+/*
+ * The CP10 ID registers are architecturally mapped to AArch64 feature
+ * registers. Abuse that fact so we can rely on the AArch64 handler for accesses
+ * from AArch32.
+ */
+static bool kvm_esr_cp10_id_to_sys64(u64 esr, struct sys_reg_params *params)
+{
+	u8 reg_id = (esr >> 10) & 0xf;
+	bool valid;
+
+	params->is_write = ((esr & 1) == 0);
+	params->Op0 = 3;
+	params->Op1 = 0;
+	params->CRn = 0;
+	params->CRm = 3;
+
+	/* CP10 ID registers are read-only */
+	valid = !params->is_write;
+
+	switch (reg_id) {
+	/* MVFR0 */
+	case 0b0111:
+		params->Op2 = 0;
+		break;
+	/* MVFR1 */
+	case 0b0110:
+		params->Op2 = 1;
+		break;
+	/* MVFR2 */
+	case 0b0101:
+		params->Op2 = 2;
+		break;
+	default:
+		valid = false;
+	}
+
+	if (valid)
+		return true;
+
+	kvm_pr_unimpl("Unhandled cp10 register %s: %u\n",
+		      params->is_write ? "write" : "read", reg_id);
+	return false;
+}
+
+/**
+ * kvm_handle_cp10_id() - Handles a VMRS trap on guest access to a 'Media and
+ *			  VFP Register' from AArch32.
+ * @vcpu: The vCPU pointer
+ *
+ * MVFR{0-2} are architecturally mapped to the AArch64 MVFR{0-2}_EL1 registers.
+ * Work out the correct AArch64 system register encoding and reroute to the
+ * AArch64 system register emulation.
+ */
+int kvm_handle_cp10_id(struct kvm_vcpu *vcpu)
+{
+	int Rt = kvm_vcpu_sys_get_rt(vcpu);
+	u64 esr = kvm_vcpu_get_esr(vcpu);
+	struct sys_reg_params params;
+
+	/* UNDEF on any unhandled register access */
+	if (!kvm_esr_cp10_id_to_sys64(esr, &params)) {
+		kvm_inject_undefined(vcpu);
+		return 1;
+	}
+
+	if (emulate_sys_reg(vcpu, &params))
+		vcpu_set_reg(vcpu, Rt, params.regval);
+
+	return 1;
+}
+
+/**
+ * kvm_emulate_cp15_id_reg() - Handles an MRC trap on a guest CP15 access where
+ *			       CRn=0, which corresponds to the AArch32 feature
+ *			       registers.
+ * @vcpu: the vCPU pointer
+ * @params: the system register access parameters.
+ *
+ * Our cp15 system register tables do not enumerate the AArch32 feature
+ * registers. Conveniently, our AArch64 table does, and the AArch32 system
+ * register encoding can be trivially remapped into the AArch64 for the feature
+ * registers: Append op0=3, leaving op1, CRn, CRm, and op2 the same.
+ *
+ * According to DDI0487G.b G7.3.1, paragraph "Behavior of VMSAv8-32 32-bit
+ * System registers with (coproc=0b1111, CRn==c0)", read accesses from this
+ * range are either UNKNOWN or RES0. Rerouting remains architectural as we
+ * treat undefined registers in this range as RAZ.
+ */
+static int kvm_emulate_cp15_id_reg(struct kvm_vcpu *vcpu,
+				   struct sys_reg_params *params)
+{
+	int Rt = kvm_vcpu_sys_get_rt(vcpu);
+
+	/* Treat impossible writes to RO registers as UNDEFINED */
+	if (params->is_write) {
+		unhandled_cp_access(vcpu, params);
+		return 1;
+	}
+
+	params->Op0 = 3;
+
+	/*
+	 * All registers where CRm > 3 are known to be UNKNOWN/RAZ from AArch32.
+	 * Avoid conflicting with future expansion of AArch64 feature registers
+	 * and simply treat them as RAZ here.
+	 */
+	if (params->CRm > 3)
+		params->regval = 0;
+	else if (!emulate_sys_reg(vcpu, params))
+		return 1;
+
+	vcpu_set_reg(vcpu, Rt, params->regval);
+	return 1;
+}
+
 /**
  * kvm_handle_cp_32 -- handles a mrc/mcr trap on a guest CP14/CP15 access
  * @vcpu: The VCPU pointer
  * @run:  The kvm_run struct
  */
 static int kvm_handle_cp_32(struct kvm_vcpu *vcpu,
+			    struct sys_reg_params *params,
 			    const struct sys_reg_desc *global,
 			    size_t nr_global)
 {
-	struct sys_reg_params params;
-	u32 esr = kvm_vcpu_get_esr(vcpu);
 	int Rt  = kvm_vcpu_sys_get_rt(vcpu);
 
-	params.CRm = (esr >> 1) & 0xf;
-	params.regval = vcpu_get_reg(vcpu, Rt);
-	params.is_write = ((esr & 1) == 0);
-	params.CRn = (esr >> 10) & 0xf;
-	params.Op0 = 0;
-	params.Op1 = (esr >> 14) & 0x7;
-	params.Op2 = (esr >> 17) & 0x7;
+	params->regval = vcpu_get_reg(vcpu, Rt);
 
-	if (!emulate_cp(vcpu, &params, global, nr_global)) {
-		if (!params.is_write)
-			vcpu_set_reg(vcpu, Rt, params.regval);
+	if (emulate_cp(vcpu, params, global, nr_global)) {
+		if (!params->is_write)
+			vcpu_set_reg(vcpu, Rt, params->regval);
 		return 1;
 	}
 
-	unhandled_cp_access(vcpu, &params);
+	unhandled_cp_access(vcpu, params);
 	return 1;
 }
 
@@ -2337,7 +2423,20 @@ int kvm_handle_cp15_64(struct kvm_vcpu *vcpu)
 
 int kvm_handle_cp15_32(struct kvm_vcpu *vcpu)
 {
-	return kvm_handle_cp_32(vcpu, cp15_regs, ARRAY_SIZE(cp15_regs));
+	struct sys_reg_params params;
+
+	params = esr_cp1x_32_to_params(kvm_vcpu_get_esr(vcpu));
+
+	/*
+	 * Certain AArch32 ID registers are handled by rerouting to the AArch64
+	 * system register table. Registers in the ID range where CRm=0 are
+	 * excluded from this scheme as they do not trivially map into AArch64
+	 * system register encodings.
+	 */
+	if (params.Op1 == 0 && params.CRn == 0 && params.CRm)
+		return kvm_emulate_cp15_id_reg(vcpu, &params);
+
+	return kvm_handle_cp_32(vcpu, &params, cp15_regs, ARRAY_SIZE(cp15_regs));
 }
 
 int kvm_handle_cp14_64(struct kvm_vcpu *vcpu)
@@ -2347,7 +2446,11 @@ int kvm_handle_cp14_64(struct kvm_vcpu *vcpu)
 
 int kvm_handle_cp14_32(struct kvm_vcpu *vcpu)
 {
-	return kvm_handle_cp_32(vcpu, cp14_regs, ARRAY_SIZE(cp14_regs));
+	struct sys_reg_params params;
+
+	params = esr_cp1x_32_to_params(kvm_vcpu_get_esr(vcpu));
+
+	return kvm_handle_cp_32(vcpu, &params, cp14_regs, ARRAY_SIZE(cp14_regs));
 }
 
 static bool is_imp_def_sys_reg(struct sys_reg_params *params)
@@ -2356,7 +2459,14 @@ static bool is_imp_def_sys_reg(struct sys_reg_params *params)
 	return params->Op0 == 3 && (params->CRn & 0b1011) == 0b1011;
 }
 
-static int emulate_sys_reg(struct kvm_vcpu *vcpu,
+/**
+ * emulate_sys_reg - Emulate a guest access to an AArch64 system register
+ * @vcpu: The VCPU pointer
+ * @params: Decoded system register parameters
+ *
+ * Return: true if the system register access was successful, false otherwise.
+ */
+static bool emulate_sys_reg(struct kvm_vcpu *vcpu,
 			   struct sys_reg_params *params)
 {
 	const struct sys_reg_desc *r;
@@ -2365,7 +2475,10 @@ static int emulate_sys_reg(struct kvm_vcpu *vcpu,
 
 	if (likely(r)) {
 		perform_access(vcpu, params, r);
-	} else if (is_imp_def_sys_reg(params)) {
+		return true;
+	}
+
+	if (is_imp_def_sys_reg(params)) {
 		kvm_inject_undefined(vcpu);
 	} else {
 		print_sys_reg_msg(params,
@@ -2373,7 +2486,7 @@ static int emulate_sys_reg(struct kvm_vcpu *vcpu,
 				  *vcpu_pc(vcpu), *vcpu_cpsr(vcpu));
 		kvm_inject_undefined(vcpu);
 	}
-	return 1;
+	return false;
 }
 
 /**
@@ -2401,18 +2514,18 @@ int kvm_handle_sys_reg(struct kvm_vcpu *vcpu)
 	struct sys_reg_params params;
 	unsigned long esr = kvm_vcpu_get_esr(vcpu);
 	int Rt = kvm_vcpu_sys_get_rt(vcpu);
-	int ret;
 
 	trace_kvm_handle_sys_reg(esr);
 
 	params = esr_sys64_to_params(esr);
 	params.regval = vcpu_get_reg(vcpu, Rt);
 
-	ret = emulate_sys_reg(vcpu, &params);
+	if (!emulate_sys_reg(vcpu, &params))
+		return 1;
 
 	if (!params.is_write)
 		vcpu_set_reg(vcpu, Rt, params.regval);
-	return ret;
+	return 1;
 }
 
 /******************************************************************************
@@ -2448,35 +2561,34 @@ static bool index_to_params(u64 id, struct sys_reg_params *params)
 	}
 }
 
-const struct sys_reg_desc *find_reg_by_id(u64 id,
-					  struct sys_reg_params *params,
-					  const struct sys_reg_desc table[],
-					  unsigned int num)
+const struct sys_reg_desc *get_reg_by_id(u64 id,
+					 const struct sys_reg_desc table[],
+					 unsigned int num)
 {
-	if (!index_to_params(id, params))
+	struct sys_reg_params params;
+
+	if (!index_to_params(id, &params))
 		return NULL;
 
-	return find_reg(params, table, num);
+	return find_reg(&params, table, num);
 }
 
 /* Decode an index value, and find the sys_reg_desc entry. */
-static const struct sys_reg_desc *index_to_sys_reg_desc(struct kvm_vcpu *vcpu,
-						    u64 id)
+static const struct sys_reg_desc *
+id_to_sys_reg_desc(struct kvm_vcpu *vcpu, u64 id,
+		   const struct sys_reg_desc table[], unsigned int num)
+
 {
 	const struct sys_reg_desc *r;
-	struct sys_reg_params params;
 
 	/* We only do sys_reg for now. */
 	if ((id & KVM_REG_ARM_COPROC_MASK) != KVM_REG_ARM64_SYSREG)
 		return NULL;
 
-	if (!index_to_params(id, &params))
-		return NULL;
-
-	r = find_reg(&params, sys_reg_descs, ARRAY_SIZE(sys_reg_descs));
+	r = get_reg_by_id(id, table, num);
 
 	/* Not saved in the sys_reg array and not otherwise accessible? */
-	if (r && !(r->reg || r->get_user))
+	if (r && (!(r->reg || r->get_user) || sysreg_hidden(vcpu, r)))
 		r = NULL;
 
 	return r;
@@ -2516,48 +2628,30 @@ static struct sys_reg_desc invariant_sys_regs[] = {
 	{ SYS_DESC(SYS_CTR_EL0), NULL, get_ctr_el0 },
 };
 
-static int reg_from_user(u64 *val, const void __user *uaddr, u64 id)
-{
-	if (copy_from_user(val, uaddr, KVM_REG_SIZE(id)) != 0)
-		return -EFAULT;
-	return 0;
-}
-
-static int reg_to_user(void __user *uaddr, const u64 *val, u64 id)
+static int get_invariant_sys_reg(u64 id, u64 __user *uaddr)
 {
-	if (copy_to_user(uaddr, val, KVM_REG_SIZE(id)) != 0)
-		return -EFAULT;
-	return 0;
-}
-
-static int get_invariant_sys_reg(u64 id, void __user *uaddr)
-{
-	struct sys_reg_params params;
 	const struct sys_reg_desc *r;
 
-	r = find_reg_by_id(id, &params, invariant_sys_regs,
-			   ARRAY_SIZE(invariant_sys_regs));
+	r = get_reg_by_id(id, invariant_sys_regs,
+			  ARRAY_SIZE(invariant_sys_regs));
 	if (!r)
 		return -ENOENT;
 
-	return reg_to_user(uaddr, &r->val, id);
+	return put_user(r->val, uaddr);
 }
 
-static int set_invariant_sys_reg(u64 id, void __user *uaddr)
+static int set_invariant_sys_reg(u64 id, u64 __user *uaddr)
 {
-	struct sys_reg_params params;
 	const struct sys_reg_desc *r;
-	int err;
-	u64 val = 0; /* Make sure high bits are 0 for 32-bit regs */
+	u64 val;
 
-	r = find_reg_by_id(id, &params, invariant_sys_regs,
-			   ARRAY_SIZE(invariant_sys_regs));
+	r = get_reg_by_id(id, invariant_sys_regs,
+			  ARRAY_SIZE(invariant_sys_regs));
 	if (!r)
 		return -ENOENT;
 
-	err = reg_from_user(&val, uaddr, id);
-	if (err)
-		return err;
+	if (get_user(val, uaddr))
+		return -EFAULT;
 
 	/* This is what we mean by invariant: you can't change it. */
 	if (r->val != val)
@@ -2648,54 +2742,89 @@ static int demux_c15_set(u64 id, void __user *uaddr)
 	}
 }
 
-int kvm_arm_sys_reg_get_reg(struct kvm_vcpu *vcpu, const struct kvm_one_reg *reg)
+int kvm_sys_reg_get_user(struct kvm_vcpu *vcpu, const struct kvm_one_reg *reg,
+			 const struct sys_reg_desc table[], unsigned int num)
 {
+	u64 __user *uaddr = (u64 __user *)(unsigned long)reg->addr;
 	const struct sys_reg_desc *r;
+	u64 val;
+	int ret;
+
+	r = id_to_sys_reg_desc(vcpu, reg->id, table, num);
+	if (!r)
+		return -ENOENT;
+
+	if (r->get_user) {
+		ret = (r->get_user)(vcpu, r, &val);
+	} else {
+		val = __vcpu_sys_reg(vcpu, r->reg);
+		ret = 0;
+	}
+
+	if (!ret)
+		ret = put_user(val, uaddr);
+
+	return ret;
+}
+
+int kvm_arm_sys_reg_get_reg(struct kvm_vcpu *vcpu, const struct kvm_one_reg *reg)
+{
 	void __user *uaddr = (void __user *)(unsigned long)reg->addr;
+	int err;
 
 	if ((reg->id & KVM_REG_ARM_COPROC_MASK) == KVM_REG_ARM_DEMUX)
 		return demux_c15_get(reg->id, uaddr);
 
-	if (KVM_REG_SIZE(reg->id) != sizeof(__u64))
-		return -ENOENT;
+	err = get_invariant_sys_reg(reg->id, uaddr);
+	if (err != -ENOENT)
+		return err;
 
-	r = index_to_sys_reg_desc(vcpu, reg->id);
-	if (!r)
-		return get_invariant_sys_reg(reg->id, uaddr);
+	return kvm_sys_reg_get_user(vcpu, reg,
+				    sys_reg_descs, ARRAY_SIZE(sys_reg_descs));
+}
 
-	/* Check for regs disabled by runtime config */
-	if (sysreg_hidden(vcpu, r))
+int kvm_sys_reg_set_user(struct kvm_vcpu *vcpu, const struct kvm_one_reg *reg,
+			 const struct sys_reg_desc table[], unsigned int num)
+{
+	u64 __user *uaddr = (u64 __user *)(unsigned long)reg->addr;
+	const struct sys_reg_desc *r;
+	u64 val;
+	int ret;
+
+	if (get_user(val, uaddr))
+		return -EFAULT;
+
+	r = id_to_sys_reg_desc(vcpu, reg->id, table, num);
+	if (!r)
 		return -ENOENT;
 
-	if (r->get_user)
-		return (r->get_user)(vcpu, r, reg, uaddr);
+	if (sysreg_user_write_ignore(vcpu, r))
+		return 0;
+
+	if (r->set_user) {
+		ret = (r->set_user)(vcpu, r, val);
+	} else {
+		__vcpu_sys_reg(vcpu, r->reg) = val;
+		ret = 0;
+	}
 
-	return reg_to_user(uaddr, &__vcpu_sys_reg(vcpu, r->reg), reg->id);
+	return ret;
 }
 
 int kvm_arm_sys_reg_set_reg(struct kvm_vcpu *vcpu, const struct kvm_one_reg *reg)
 {
-	const struct sys_reg_desc *r;
 	void __user *uaddr = (void __user *)(unsigned long)reg->addr;
+	int err;
 
 	if ((reg->id & KVM_REG_ARM_COPROC_MASK) == KVM_REG_ARM_DEMUX)
 		return demux_c15_set(reg->id, uaddr);
 
-	if (KVM_REG_SIZE(reg->id) != sizeof(__u64))
-		return -ENOENT;
-
-	r = index_to_sys_reg_desc(vcpu, reg->id);
-	if (!r)
-		return set_invariant_sys_reg(reg->id, uaddr);
-
-	/* Check for regs disabled by runtime config */
-	if (sysreg_hidden(vcpu, r))
-		return -ENOENT;
-
-	if (r->set_user)
-		return (r->set_user)(vcpu, r, reg, uaddr);
+	err = set_invariant_sys_reg(reg->id, uaddr);
+	if (err != -ENOENT)
+		return err;
 
-	return reg_from_user(&__vcpu_sys_reg(vcpu, r->reg), uaddr, reg->id);
+	return kvm_sys_reg_set_user(vcpu, reg,
+				    sys_reg_descs, ARRAY_SIZE(sys_reg_descs));
 }
 
 static unsigned int num_demux_regs(void)
@@ -2815,18 +2944,22 @@ int kvm_arm_copy_sys_reg_indices(struct kvm_vcpu *vcpu, u64 __user *uindices)
 	return write_demux_regids(uindices);
 }
 
-void kvm_sys_reg_table_init(void)
+int kvm_sys_reg_table_init(void)
 {
+	bool valid = true;
 	unsigned int i;
 	struct sys_reg_desc clidr;
 
 	/* Make sure tables are unique and in order. */
-	BUG_ON(check_sysreg_table(sys_reg_descs, ARRAY_SIZE(sys_reg_descs), false));
-	BUG_ON(check_sysreg_table(cp14_regs, ARRAY_SIZE(cp14_regs), true));
-	BUG_ON(check_sysreg_table(cp14_64_regs, ARRAY_SIZE(cp14_64_regs), true));
-	BUG_ON(check_sysreg_table(cp15_regs, ARRAY_SIZE(cp15_regs), true));
-	BUG_ON(check_sysreg_table(cp15_64_regs, ARRAY_SIZE(cp15_64_regs), true));
-	BUG_ON(check_sysreg_table(invariant_sys_regs, ARRAY_SIZE(invariant_sys_regs), false));
+	valid &= check_sysreg_table(sys_reg_descs, ARRAY_SIZE(sys_reg_descs), false);
+	valid &= check_sysreg_table(cp14_regs, ARRAY_SIZE(cp14_regs), true);
+	valid &= check_sysreg_table(cp14_64_regs, ARRAY_SIZE(cp14_64_regs), true);
+	valid &= check_sysreg_table(cp15_regs, ARRAY_SIZE(cp15_regs), true);
+	valid &= check_sysreg_table(cp15_64_regs, ARRAY_SIZE(cp15_64_regs), true);
+	valid &= check_sysreg_table(invariant_sys_regs, ARRAY_SIZE(invariant_sys_regs), false);
+
+	if (!valid)
+		return -EINVAL;
 
 	/* We abuse the reset function to overwrite the table itself. */
 	for (i = 0; i < ARRAY_SIZE(invariant_sys_regs); i++)
@@ -2849,4 +2982,6 @@ void kvm_sys_reg_table_init(void)
 			break;
 	/* Clear all higher bits. */
 	cache_levels &= (1 << (i*3))-1;
+
+	return 0;
 }
diff --git a/arch/arm64/kvm/sys_regs.h b/arch/arm64/kvm/sys_regs.h
index cc0cc95a0280..e4ebb3a379fd 100644
--- a/arch/arm64/kvm/sys_regs.h
+++ b/arch/arm64/kvm/sys_regs.h
@@ -35,12 +35,19 @@ struct sys_reg_params {
 				  .Op2 = ((esr) >> 17) & 0x7,                  \
 				  .is_write = !((esr) & 1) })
 
+#define esr_cp1x_32_to_params(esr)						\
+	((struct sys_reg_params){ .Op1 = ((esr) >> 14) & 0x7,			\
+				  .CRn = ((esr) >> 10) & 0xf,			\
+				  .CRm = ((esr) >> 1) & 0xf,			\
+				  .Op2 = ((esr) >> 17) & 0x7,			\
+				  .is_write = !((esr) & 1) })
+
 struct sys_reg_desc {
 	/* Sysreg string for debug */
 	const char *name;
 
 	enum {
-		AA32_ZEROHIGH,
+		AA32_DIRECT,
 		AA32_LO,
 		AA32_HI,
 	} aarch32_map;
@@ -68,9 +75,9 @@ struct sys_reg_desc {
 
 	/* Custom get/set_user functions, fallback to generic if NULL */
 	int (*get_user)(struct kvm_vcpu *vcpu, const struct sys_reg_desc *rd,
-			const struct kvm_one_reg *reg, void __user *uaddr);
+			u64 *val);
 	int (*set_user)(struct kvm_vcpu *vcpu, const struct sys_reg_desc *rd,
-			const struct kvm_one_reg *reg, void __user *uaddr);
+			u64 val);
 
 	/* Return mask of REG_* runtime visibility overrides */
 	unsigned int (*visibility)(const struct kvm_vcpu *vcpu,
@@ -79,6 +86,7 @@ struct sys_reg_desc {
 
 #define REG_HIDDEN		(1 << 0) /* hidden from userspace and guest */
 #define REG_RAZ			(1 << 1) /* RAZ from userspace and guest */
+#define REG_USER_WI		(1 << 2) /* WI from userspace only */
 
 static __printf(2, 3)
 inline void print_sys_reg_msg(const struct sys_reg_params *p,
@@ -129,22 +137,31 @@ static inline void reset_val(struct kvm_vcpu *vcpu, const struct sys_reg_desc *r
 	__vcpu_sys_reg(vcpu, r->reg) = r->val;
 }
 
-static inline bool sysreg_hidden(const struct kvm_vcpu *vcpu,
-				 const struct sys_reg_desc *r)
+static inline unsigned int sysreg_visibility(const struct kvm_vcpu *vcpu,
+					     const struct sys_reg_desc *r)
 {
 	if (likely(!r->visibility))
-		return false;
+		return 0;
 
-	return r->visibility(vcpu, r) & REG_HIDDEN;
+	return r->visibility(vcpu, r);
+}
+
+static inline bool sysreg_hidden(const struct kvm_vcpu *vcpu,
+				 const struct sys_reg_desc *r)
+{
+	return sysreg_visibility(vcpu, r) & REG_HIDDEN;
 }
 
 static inline bool sysreg_visible_as_raz(const struct kvm_vcpu *vcpu,
 					 const struct sys_reg_desc *r)
 {
-	if (likely(!r->visibility))
-		return false;
+	return sysreg_visibility(vcpu, r) & REG_RAZ;
+}
 
-	return r->visibility(vcpu, r) & REG_RAZ;
+static inline bool sysreg_user_write_ignore(const struct kvm_vcpu *vcpu,
+					    const struct sys_reg_desc *r)
+{
+	return sysreg_visibility(vcpu, r) & REG_USER_WI;
 }
 
 static inline int cmp_sys_reg(const struct sys_reg_desc *i1,
@@ -183,10 +200,16 @@ find_reg(const struct sys_reg_params *params, const struct sys_reg_desc table[],
 	return __inline_bsearch((void *)pval, table, num, sizeof(table[0]), match_sys_reg);
 }
 
-const struct sys_reg_desc *find_reg_by_id(u64 id,
-					  struct sys_reg_params *params,
-					  const struct sys_reg_desc table[],
-					  unsigned int num);
+const struct sys_reg_desc *get_reg_by_id(u64 id,
+					 const struct sys_reg_desc table[],
+					 unsigned int num);
+
+int kvm_arm_sys_reg_get_reg(struct kvm_vcpu *vcpu, const struct kvm_one_reg *);
+int kvm_arm_sys_reg_set_reg(struct kvm_vcpu *vcpu, const struct kvm_one_reg *);
+int kvm_sys_reg_get_user(struct kvm_vcpu *vcpu, const struct kvm_one_reg *reg,
+			 const struct sys_reg_desc table[], unsigned int num);
+int kvm_sys_reg_set_user(struct kvm_vcpu *vcpu, const struct kvm_one_reg *reg,
+			 const struct sys_reg_desc table[], unsigned int num);
 
 #define AA32(_x)	.aarch32_map = AA32_##_x
 #define Op0(_x) 	.Op0 = _x
diff --git a/arch/arm64/kvm/va_layout.c b/arch/arm64/kvm/va_layout.c
index acdb7b3cc97d..91b22a014610 100644
--- a/arch/arm64/kvm/va_layout.c
+++ b/arch/arm64/kvm/va_layout.c
@@ -169,7 +169,7 @@ void __init kvm_update_va_mask(struct alt_instr *alt,
 		 * dictates it and we don't have any spare bits in the
 		 * address), NOP everything after masking the kernel VA.
 		 */
-		if (has_vhe() || (!tag_val && i > 0)) {
+		if (cpus_have_cap(ARM64_HAS_VIRT_HOST_EXTN) || (!tag_val && i > 0)) {
 			updptr[i] = cpu_to_le32(aarch64_insn_gen_nop());
 			continue;
 		}
@@ -193,7 +193,8 @@ void kvm_patch_vector_branch(struct alt_instr *alt,
 
 	BUG_ON(nr_inst != 4);
 
-	if (!cpus_have_const_cap(ARM64_SPECTRE_V3A) || WARN_ON_ONCE(has_vhe()))
+	if (!cpus_have_cap(ARM64_SPECTRE_V3A) ||
+	    WARN_ON_ONCE(cpus_have_cap(ARM64_HAS_VIRT_HOST_EXTN)))
 		return;
 
 	/*
diff --git a/arch/arm64/kvm/vgic-sys-reg-v3.c b/arch/arm64/kvm/vgic-sys-reg-v3.c
index 07d5271e9f05..9e7c486b48c2 100644
--- a/arch/arm64/kvm/vgic-sys-reg-v3.c
+++ b/arch/arm64/kvm/vgic-sys-reg-v3.c
@@ -10,293 +10,357 @@
 #include "vgic/vgic.h"
 #include "sys_regs.h"
 
-static bool access_gic_ctlr(struct kvm_vcpu *vcpu, struct sys_reg_params *p,
-			    const struct sys_reg_desc *r)
+static int set_gic_ctlr(struct kvm_vcpu *vcpu, const struct sys_reg_desc *r,
+			u64 val)
 {
 	u32 host_pri_bits, host_id_bits, host_seis, host_a3v, seis, a3v;
 	struct vgic_cpu *vgic_v3_cpu = &vcpu->arch.vgic_cpu;
 	struct vgic_vmcr vmcr;
+
+	vgic_get_vmcr(vcpu, &vmcr);
+
+	/*
+	 * Disallow restoring VM state if not supported by this
+	 * hardware.
+	 */
+	host_pri_bits = FIELD_GET(ICC_CTLR_EL1_PRI_BITS_MASK, val) + 1;
+	if (host_pri_bits > vgic_v3_cpu->num_pri_bits)
+		return -EINVAL;
+
+	vgic_v3_cpu->num_pri_bits = host_pri_bits;
+
+	host_id_bits = FIELD_GET(ICC_CTLR_EL1_ID_BITS_MASK, val);
+	if (host_id_bits > vgic_v3_cpu->num_id_bits)
+		return -EINVAL;
+
+	vgic_v3_cpu->num_id_bits = host_id_bits;
+
+	host_seis = FIELD_GET(ICH_VTR_SEIS_MASK, kvm_vgic_global_state.ich_vtr_el2);
+	seis = FIELD_GET(ICC_CTLR_EL1_SEIS_MASK, val);
+	if (host_seis != seis)
+		return -EINVAL;
+
+	host_a3v = FIELD_GET(ICH_VTR_A3V_MASK, kvm_vgic_global_state.ich_vtr_el2);
+	a3v = FIELD_GET(ICC_CTLR_EL1_A3V_MASK, val);
+	if (host_a3v != a3v)
+		return -EINVAL;
+
+	/*
+	 * Here set VMCR.CTLR in ICC_CTLR_EL1 layout.
+	 * The vgic_set_vmcr() will convert to ICH_VMCR layout.
+	 */
+	vmcr.cbpr = FIELD_GET(ICC_CTLR_EL1_CBPR_MASK, val);
+	vmcr.eoim = FIELD_GET(ICC_CTLR_EL1_EOImode_MASK, val);
+	vgic_set_vmcr(vcpu, &vmcr);
+
+	return 0;
+}
+
+static int get_gic_ctlr(struct kvm_vcpu *vcpu, const struct sys_reg_desc *r,
+			u64 *valp)
+{
+	struct vgic_cpu *vgic_v3_cpu = &vcpu->arch.vgic_cpu;
+	struct vgic_vmcr vmcr;
 	u64 val;
 
 	vgic_get_vmcr(vcpu, &vmcr);
-	if (p->is_write) {
-		val = p->regval;
-
-		/*
-		 * Disallow restoring VM state if not supported by this
-		 * hardware.
-		 */
-		host_pri_bits = ((val & ICC_CTLR_EL1_PRI_BITS_MASK) >>
-				 ICC_CTLR_EL1_PRI_BITS_SHIFT) + 1;
-		if (host_pri_bits > vgic_v3_cpu->num_pri_bits)
-			return false;
-
-		vgic_v3_cpu->num_pri_bits = host_pri_bits;
-
-		host_id_bits = (val & ICC_CTLR_EL1_ID_BITS_MASK) >>
-				ICC_CTLR_EL1_ID_BITS_SHIFT;
-		if (host_id_bits > vgic_v3_cpu->num_id_bits)
-			return false;
-
-		vgic_v3_cpu->num_id_bits = host_id_bits;
-
-		host_seis = ((kvm_vgic_global_state.ich_vtr_el2 &
-			     ICH_VTR_SEIS_MASK) >> ICH_VTR_SEIS_SHIFT);
-		seis = (val & ICC_CTLR_EL1_SEIS_MASK) >>
-			ICC_CTLR_EL1_SEIS_SHIFT;
-		if (host_seis != seis)
-			return false;
-
-		host_a3v = ((kvm_vgic_global_state.ich_vtr_el2 &
-			    ICH_VTR_A3V_MASK) >> ICH_VTR_A3V_SHIFT);
-		a3v = (val & ICC_CTLR_EL1_A3V_MASK) >> ICC_CTLR_EL1_A3V_SHIFT;
-		if (host_a3v != a3v)
-			return false;
-
-		/*
-		 * Here set VMCR.CTLR in ICC_CTLR_EL1 layout.
-		 * The vgic_set_vmcr() will convert to ICH_VMCR layout.
-		 */
-		vmcr.cbpr = (val & ICC_CTLR_EL1_CBPR_MASK) >> ICC_CTLR_EL1_CBPR_SHIFT;
-		vmcr.eoim = (val & ICC_CTLR_EL1_EOImode_MASK) >> ICC_CTLR_EL1_EOImode_SHIFT;
-		vgic_set_vmcr(vcpu, &vmcr);
-	} else {
-		val = 0;
-		val |= (vgic_v3_cpu->num_pri_bits - 1) <<
-			ICC_CTLR_EL1_PRI_BITS_SHIFT;
-		val |= vgic_v3_cpu->num_id_bits << ICC_CTLR_EL1_ID_BITS_SHIFT;
-		val |= ((kvm_vgic_global_state.ich_vtr_el2 &
-			ICH_VTR_SEIS_MASK) >> ICH_VTR_SEIS_SHIFT) <<
-			ICC_CTLR_EL1_SEIS_SHIFT;
-		val |= ((kvm_vgic_global_state.ich_vtr_el2 &
-			ICH_VTR_A3V_MASK) >> ICH_VTR_A3V_SHIFT) <<
-			ICC_CTLR_EL1_A3V_SHIFT;
-		/*
-		 * The VMCR.CTLR value is in ICC_CTLR_EL1 layout.
-		 * Extract it directly using ICC_CTLR_EL1 reg definitions.
-		 */
-		val |= (vmcr.cbpr << ICC_CTLR_EL1_CBPR_SHIFT) & ICC_CTLR_EL1_CBPR_MASK;
-		val |= (vmcr.eoim << ICC_CTLR_EL1_EOImode_SHIFT) & ICC_CTLR_EL1_EOImode_MASK;
-
-		p->regval = val;
-	}
+	val = 0;
+	val |= FIELD_PREP(ICC_CTLR_EL1_PRI_BITS_MASK, vgic_v3_cpu->num_pri_bits - 1);
+	val |= FIELD_PREP(ICC_CTLR_EL1_ID_BITS_MASK, vgic_v3_cpu->num_id_bits);
+	val |= FIELD_PREP(ICC_CTLR_EL1_SEIS_MASK,
+			  FIELD_GET(ICH_VTR_SEIS_MASK,
+				    kvm_vgic_global_state.ich_vtr_el2));
+	val |= FIELD_PREP(ICC_CTLR_EL1_A3V_MASK,
+			  FIELD_GET(ICH_VTR_A3V_MASK, kvm_vgic_global_state.ich_vtr_el2));
+	/*
+	 * The VMCR.CTLR value is in ICC_CTLR_EL1 layout.
+	 * Extract it directly using ICC_CTLR_EL1 reg definitions.
+	 */
+	val |= FIELD_PREP(ICC_CTLR_EL1_CBPR_MASK, vmcr.cbpr);
+	val |= FIELD_PREP(ICC_CTLR_EL1_EOImode_MASK, vmcr.eoim);
+
+	*valp = val;
 
-	return true;
+	return 0;
 }
 
-static bool access_gic_pmr(struct kvm_vcpu *vcpu, struct sys_reg_params *p,
-			   const struct sys_reg_desc *r)
+static int set_gic_pmr(struct kvm_vcpu *vcpu, const struct sys_reg_desc *r,
+		       u64 val)
 {
 	struct vgic_vmcr vmcr;
 
 	vgic_get_vmcr(vcpu, &vmcr);
-	if (p->is_write) {
-		vmcr.pmr = (p->regval & ICC_PMR_EL1_MASK) >> ICC_PMR_EL1_SHIFT;
-		vgic_set_vmcr(vcpu, &vmcr);
-	} else {
-		p->regval = (vmcr.pmr << ICC_PMR_EL1_SHIFT) & ICC_PMR_EL1_MASK;
-	}
+	vmcr.pmr = FIELD_GET(ICC_PMR_EL1_MASK, val);
+	vgic_set_vmcr(vcpu, &vmcr);
 
-	return true;
+	return 0;
 }
 
-static bool access_gic_bpr0(struct kvm_vcpu *vcpu, struct sys_reg_params *p,
-			    const struct sys_reg_desc *r)
+static int get_gic_pmr(struct kvm_vcpu *vcpu, const struct sys_reg_desc *r,
+		       u64 *val)
 {
 	struct vgic_vmcr vmcr;
 
 	vgic_get_vmcr(vcpu, &vmcr);
-	if (p->is_write) {
-		vmcr.bpr = (p->regval & ICC_BPR0_EL1_MASK) >>
-			    ICC_BPR0_EL1_SHIFT;
-		vgic_set_vmcr(vcpu, &vmcr);
-	} else {
-		p->regval = (vmcr.bpr << ICC_BPR0_EL1_SHIFT) &
-			     ICC_BPR0_EL1_MASK;
-	}
+	*val = FIELD_PREP(ICC_PMR_EL1_MASK, vmcr.pmr);
 
-	return true;
+	return 0;
 }
 
-static bool access_gic_bpr1(struct kvm_vcpu *vcpu, struct sys_reg_params *p,
-			    const struct sys_reg_desc *r)
+static int set_gic_bpr0(struct kvm_vcpu *vcpu, const struct sys_reg_desc *r,
+			u64 val)
 {
 	struct vgic_vmcr vmcr;
 
-	if (!p->is_write)
-		p->regval = 0;
+	vgic_get_vmcr(vcpu, &vmcr);
+	vmcr.bpr = FIELD_GET(ICC_BPR0_EL1_MASK, val);
+	vgic_set_vmcr(vcpu, &vmcr);
+
+	return 0;
+}
+
+static int get_gic_bpr0(struct kvm_vcpu *vcpu, const struct sys_reg_desc *r,
+			u64 *val)
+{
+	struct vgic_vmcr vmcr;
 
 	vgic_get_vmcr(vcpu, &vmcr);
-	if (!vmcr.cbpr) {
-		if (p->is_write) {
-			vmcr.abpr = (p->regval & ICC_BPR1_EL1_MASK) >>
-				     ICC_BPR1_EL1_SHIFT;
-			vgic_set_vmcr(vcpu, &vmcr);
-		} else {
-			p->regval = (vmcr.abpr << ICC_BPR1_EL1_SHIFT) &
-				     ICC_BPR1_EL1_MASK;
-		}
-	} else {
-		if (!p->is_write)
-			p->regval = min((vmcr.bpr + 1), 7U);
-	}
+	*val = FIELD_PREP(ICC_BPR0_EL1_MASK, vmcr.bpr);
 
-	return true;
+	return 0;
 }
 
-static bool access_gic_grpen0(struct kvm_vcpu *vcpu, struct sys_reg_params *p,
-			      const struct sys_reg_desc *r)
+static int set_gic_bpr1(struct kvm_vcpu *vcpu, const struct sys_reg_desc *r,
+			u64 val)
 {
 	struct vgic_vmcr vmcr;
 
 	vgic_get_vmcr(vcpu, &vmcr);
-	if (p->is_write) {
-		vmcr.grpen0 = (p->regval & ICC_IGRPEN0_EL1_MASK) >>
-			       ICC_IGRPEN0_EL1_SHIFT;
+	if (!vmcr.cbpr) {
+		vmcr.abpr = FIELD_GET(ICC_BPR1_EL1_MASK, val);
 		vgic_set_vmcr(vcpu, &vmcr);
-	} else {
-		p->regval = (vmcr.grpen0 << ICC_IGRPEN0_EL1_SHIFT) &
-			     ICC_IGRPEN0_EL1_MASK;
 	}
 
-	return true;
+	return 0;
 }
 
-static bool access_gic_grpen1(struct kvm_vcpu *vcpu, struct sys_reg_params *p,
-			      const struct sys_reg_desc *r)
+static int get_gic_bpr1(struct kvm_vcpu *vcpu, const struct sys_reg_desc *r,
+			u64 *val)
 {
 	struct vgic_vmcr vmcr;
 
 	vgic_get_vmcr(vcpu, &vmcr);
-	if (p->is_write) {
-		vmcr.grpen1 = (p->regval & ICC_IGRPEN1_EL1_MASK) >>
-			       ICC_IGRPEN1_EL1_SHIFT;
-		vgic_set_vmcr(vcpu, &vmcr);
-	} else {
-		p->regval = (vmcr.grpen1 << ICC_IGRPEN1_EL1_SHIFT) &
-			     ICC_IGRPEN1_EL1_MASK;
-	}
+	if (!vmcr.cbpr)
+		*val = FIELD_PREP(ICC_BPR1_EL1_MASK, vmcr.abpr);
+	else
+		*val = min((vmcr.bpr + 1), 7U);
+
+
+	return 0;
+}
+
+static int set_gic_grpen0(struct kvm_vcpu *vcpu, const struct sys_reg_desc *r,
+			  u64 val)
+{
+	struct vgic_vmcr vmcr;
+
+	vgic_get_vmcr(vcpu, &vmcr);
+	vmcr.grpen0 = FIELD_GET(ICC_IGRPEN0_EL1_MASK, val);
+	vgic_set_vmcr(vcpu, &vmcr);
+
+	return 0;
+}
+
+static int get_gic_grpen0(struct kvm_vcpu *vcpu, const struct sys_reg_desc *r,
+			  u64 *val)
+{
+	struct vgic_vmcr vmcr;
+
+	vgic_get_vmcr(vcpu, &vmcr);
+	*val = FIELD_PREP(ICC_IGRPEN0_EL1_MASK, vmcr.grpen0);
 
-	return true;
+	return 0;
 }
 
-static void vgic_v3_access_apr_reg(struct kvm_vcpu *vcpu,
-				   struct sys_reg_params *p, u8 apr, u8 idx)
+static int set_gic_grpen1(struct kvm_vcpu *vcpu, const struct sys_reg_desc *r,
+			  u64 val)
+{
+	struct vgic_vmcr vmcr;
+
+	vgic_get_vmcr(vcpu, &vmcr);
+	vmcr.grpen1 = FIELD_GET(ICC_IGRPEN1_EL1_MASK, val);
+	vgic_set_vmcr(vcpu, &vmcr);
+
+	return 0;
+}
+
+static int get_gic_grpen1(struct kvm_vcpu *vcpu, const struct sys_reg_desc *r,
+			  u64 *val)
+{
+	struct vgic_vmcr vmcr;
+
+	vgic_get_vmcr(vcpu, &vmcr);
+	*val = FIELD_GET(ICC_IGRPEN1_EL1_MASK, vmcr.grpen1);
+
+	return 0;
+}
+
+static void set_apr_reg(struct kvm_vcpu *vcpu, u64 val, u8 apr, u8 idx)
 {
 	struct vgic_v3_cpu_if *vgicv3 = &vcpu->arch.vgic_cpu.vgic_v3;
-	uint32_t *ap_reg;
 
 	if (apr)
-		ap_reg = &vgicv3->vgic_ap1r[idx];
+		vgicv3->vgic_ap1r[idx] = val;
 	else
-		ap_reg = &vgicv3->vgic_ap0r[idx];
+		vgicv3->vgic_ap0r[idx] = val;
+}
+
+static u64 get_apr_reg(struct kvm_vcpu *vcpu, u8 apr, u8 idx)
+{
+	struct vgic_v3_cpu_if *vgicv3 = &vcpu->arch.vgic_cpu.vgic_v3;
 
-	if (p->is_write)
-		*ap_reg = p->regval;
+	if (apr)
+		return vgicv3->vgic_ap1r[idx];
 	else
-		p->regval = *ap_reg;
+		return vgicv3->vgic_ap0r[idx];
+}
+
+static int set_gic_ap0r(struct kvm_vcpu *vcpu, const struct sys_reg_desc *r,
+			u64 val)
+
+{
+	u8 idx = r->Op2 & 3;
+
+	if (idx > vgic_v3_max_apr_idx(vcpu))
+		return -EINVAL;
+
+	set_apr_reg(vcpu, val, 0, idx);
+	return 0;
 }
 
-static bool access_gic_aprn(struct kvm_vcpu *vcpu, struct sys_reg_params *p,
-			    const struct sys_reg_desc *r, u8 apr)
+static int get_gic_ap0r(struct kvm_vcpu *vcpu, const struct sys_reg_desc *r,
+			u64 *val)
 {
 	u8 idx = r->Op2 & 3;
 
 	if (idx > vgic_v3_max_apr_idx(vcpu))
-		goto err;
+		return -EINVAL;
 
-	vgic_v3_access_apr_reg(vcpu, p, apr, idx);
-	return true;
-err:
-	if (!p->is_write)
-		p->regval = 0;
+	*val = get_apr_reg(vcpu, 0, idx);
 
-	return false;
+	return 0;
 }
 
-static bool access_gic_ap0r(struct kvm_vcpu *vcpu, struct sys_reg_params *p,
-			    const struct sys_reg_desc *r)
+static int set_gic_ap1r(struct kvm_vcpu *vcpu, const struct sys_reg_desc *r,
+			u64 val)
+
+{
+	u8 idx = r->Op2 & 3;
+
+	if (idx > vgic_v3_max_apr_idx(vcpu))
+		return -EINVAL;
+
+	set_apr_reg(vcpu, val, 1, idx);
+	return 0;
+}
 
+static int get_gic_ap1r(struct kvm_vcpu *vcpu, const struct sys_reg_desc *r,
+			u64 *val)
 {
-	return access_gic_aprn(vcpu, p, r, 0);
+	u8 idx = r->Op2 & 3;
+
+	if (idx > vgic_v3_max_apr_idx(vcpu))
+		return -EINVAL;
+
+	*val = get_apr_reg(vcpu, 1, idx);
+
+	return 0;
 }
 
-static bool access_gic_ap1r(struct kvm_vcpu *vcpu, struct sys_reg_params *p,
-			    const struct sys_reg_desc *r)
+static int set_gic_sre(struct kvm_vcpu *vcpu, const struct sys_reg_desc *r,
+		       u64 val)
 {
-	return access_gic_aprn(vcpu, p, r, 1);
+	/* Validate SRE bit */
+	if (!(val & ICC_SRE_EL1_SRE))
+		return -EINVAL;
+
+	return 0;
 }
 
-static bool access_gic_sre(struct kvm_vcpu *vcpu, struct sys_reg_params *p,
-			   const struct sys_reg_desc *r)
+static int get_gic_sre(struct kvm_vcpu *vcpu, const struct sys_reg_desc *r,
+		       u64 *val)
 {
 	struct vgic_v3_cpu_if *vgicv3 = &vcpu->arch.vgic_cpu.vgic_v3;
 
-	/* Validate SRE bit */
-	if (p->is_write) {
-		if (!(p->regval & ICC_SRE_EL1_SRE))
-			return false;
-	} else {
-		p->regval = vgicv3->vgic_sre;
-	}
+	*val = vgicv3->vgic_sre;
 
-	return true;
+	return 0;
 }
+
 static const struct sys_reg_desc gic_v3_icc_reg_descs[] = {
-	{ SYS_DESC(SYS_ICC_PMR_EL1), access_gic_pmr },
-	{ SYS_DESC(SYS_ICC_BPR0_EL1), access_gic_bpr0 },
-	{ SYS_DESC(SYS_ICC_AP0R0_EL1), access_gic_ap0r },
-	{ SYS_DESC(SYS_ICC_AP0R1_EL1), access_gic_ap0r },
-	{ SYS_DESC(SYS_ICC_AP0R2_EL1), access_gic_ap0r },
-	{ SYS_DESC(SYS_ICC_AP0R3_EL1), access_gic_ap0r },
-	{ SYS_DESC(SYS_ICC_AP1R0_EL1), access_gic_ap1r },
-	{ SYS_DESC(SYS_ICC_AP1R1_EL1), access_gic_ap1r },
-	{ SYS_DESC(SYS_ICC_AP1R2_EL1), access_gic_ap1r },
-	{ SYS_DESC(SYS_ICC_AP1R3_EL1), access_gic_ap1r },
-	{ SYS_DESC(SYS_ICC_BPR1_EL1), access_gic_bpr1 },
-	{ SYS_DESC(SYS_ICC_CTLR_EL1), access_gic_ctlr },
-	{ SYS_DESC(SYS_ICC_SRE_EL1), access_gic_sre },
-	{ SYS_DESC(SYS_ICC_IGRPEN0_EL1), access_gic_grpen0 },
-	{ SYS_DESC(SYS_ICC_IGRPEN1_EL1), access_gic_grpen1 },
+	{ SYS_DESC(SYS_ICC_PMR_EL1),
+	  .set_user = set_gic_pmr, .get_user = get_gic_pmr, },
+	{ SYS_DESC(SYS_ICC_BPR0_EL1),
+	  .set_user = set_gic_bpr0, .get_user = get_gic_bpr0, },
+	{ SYS_DESC(SYS_ICC_AP0R0_EL1),
+	  .set_user = set_gic_ap0r, .get_user = get_gic_ap0r, },
+	{ SYS_DESC(SYS_ICC_AP0R1_EL1),
+	  .set_user = set_gic_ap0r, .get_user = get_gic_ap0r, },
+	{ SYS_DESC(SYS_ICC_AP0R2_EL1),
+	  .set_user = set_gic_ap0r, .get_user = get_gic_ap0r, },
+	{ SYS_DESC(SYS_ICC_AP0R3_EL1),
+	  .set_user = set_gic_ap0r, .get_user = get_gic_ap0r, },
+	{ SYS_DESC(SYS_ICC_AP1R0_EL1),
+	  .set_user = set_gic_ap1r, .get_user = get_gic_ap1r, },
+	{ SYS_DESC(SYS_ICC_AP1R1_EL1),
+	  .set_user = set_gic_ap1r, .get_user = get_gic_ap1r, },
+	{ SYS_DESC(SYS_ICC_AP1R2_EL1),
+	  .set_user = set_gic_ap1r, .get_user = get_gic_ap1r, },
+	{ SYS_DESC(SYS_ICC_AP1R3_EL1),
+	  .set_user = set_gic_ap1r, .get_user = get_gic_ap1r, },
+	{ SYS_DESC(SYS_ICC_BPR1_EL1),
+	  .set_user = set_gic_bpr1, .get_user = get_gic_bpr1, },
+	{ SYS_DESC(SYS_ICC_CTLR_EL1),
+	  .set_user = set_gic_ctlr, .get_user = get_gic_ctlr, },
+	{ SYS_DESC(SYS_ICC_SRE_EL1),
+	  .set_user = set_gic_sre, .get_user = get_gic_sre, },
+	{ SYS_DESC(SYS_ICC_IGRPEN0_EL1),
+	  .set_user = set_gic_grpen0, .get_user = get_gic_grpen0, },
+	{ SYS_DESC(SYS_ICC_IGRPEN1_EL1),
+	  .set_user = set_gic_grpen1, .get_user = get_gic_grpen1, },
 };
 
-int vgic_v3_has_cpu_sysregs_attr(struct kvm_vcpu *vcpu, bool is_write, u64 id,
-				u64 *reg)
+static u64 attr_to_id(u64 attr)
 {
-	struct sys_reg_params params;
-	u64 sysreg = (id & KVM_DEV_ARM_VGIC_SYSREG_MASK) | KVM_REG_SIZE_U64;
-
-	params.regval = *reg;
-	params.is_write = is_write;
+	return ARM64_SYS_REG(FIELD_GET(KVM_REG_ARM_VGIC_SYSREG_OP0_MASK, attr),
+			     FIELD_GET(KVM_REG_ARM_VGIC_SYSREG_OP1_MASK, attr),
+			     FIELD_GET(KVM_REG_ARM_VGIC_SYSREG_CRN_MASK, attr),
+			     FIELD_GET(KVM_REG_ARM_VGIC_SYSREG_CRM_MASK, attr),
+			     FIELD_GET(KVM_REG_ARM_VGIC_SYSREG_OP2_MASK, attr));
+}
 
-	if (find_reg_by_id(sysreg, &params, gic_v3_icc_reg_descs,
-			      ARRAY_SIZE(gic_v3_icc_reg_descs)))
+int vgic_v3_has_cpu_sysregs_attr(struct kvm_vcpu *vcpu, struct kvm_device_attr *attr)
+{
+	if (get_reg_by_id(attr_to_id(attr->attr), gic_v3_icc_reg_descs,
+			  ARRAY_SIZE(gic_v3_icc_reg_descs)))
 		return 0;
 
 	return -ENXIO;
 }
 
-int vgic_v3_cpu_sysregs_uaccess(struct kvm_vcpu *vcpu, bool is_write, u64 id,
-				u64 *reg)
+int vgic_v3_cpu_sysregs_uaccess(struct kvm_vcpu *vcpu,
+				struct kvm_device_attr *attr,
+				bool is_write)
 {
-	struct sys_reg_params params;
-	const struct sys_reg_desc *r;
-	u64 sysreg = (id & KVM_DEV_ARM_VGIC_SYSREG_MASK) | KVM_REG_SIZE_U64;
+	struct kvm_one_reg reg = {
+		.id	= attr_to_id(attr->attr),
+		.addr	= attr->addr,
+	};
 
 	if (is_write)
-		params.regval = *reg;
-	params.is_write = is_write;
-
-	r = find_reg_by_id(sysreg, &params, gic_v3_icc_reg_descs,
-			   ARRAY_SIZE(gic_v3_icc_reg_descs));
-	if (!r)
-		return -ENXIO;
-
-	if (!r->access(vcpu, &params, r))
-		return -EINVAL;
-
-	if (!is_write)
-		*reg = params.regval;
-
-	return 0;
+		return kvm_sys_reg_set_user(vcpu, &reg, gic_v3_icc_reg_descs,
+					    ARRAY_SIZE(gic_v3_icc_reg_descs));
+	else
+		return kvm_sys_reg_get_user(vcpu, &reg, gic_v3_icc_reg_descs,
+					    ARRAY_SIZE(gic_v3_icc_reg_descs));
 }
diff --git a/arch/arm64/kvm/vgic/vgic-debug.c b/arch/arm64/kvm/vgic/vgic-debug.c
index f38c40a76251..78cde687383c 100644
--- a/arch/arm64/kvm/vgic/vgic-debug.c
+++ b/arch/arm64/kvm/vgic/vgic-debug.c
@@ -82,7 +82,7 @@ static bool end_of_vgic(struct vgic_state_iter *iter)
 
 static void *vgic_debug_start(struct seq_file *s, loff_t *pos)
 {
-	struct kvm *kvm = (struct kvm *)s->private;
+	struct kvm *kvm = s->private;
 	struct vgic_state_iter *iter;
 
 	mutex_lock(&kvm->lock);
@@ -110,7 +110,7 @@ out:
 
 static void *vgic_debug_next(struct seq_file *s, void *v, loff_t *pos)
 {
-	struct kvm *kvm = (struct kvm *)s->private;
+	struct kvm *kvm = s->private;
 	struct vgic_state_iter *iter = kvm->arch.vgic.iter;
 
 	++*pos;
@@ -122,7 +122,7 @@ static void *vgic_debug_next(struct seq_file *s, void *v, loff_t *pos)
 
 static void vgic_debug_stop(struct seq_file *s, void *v)
 {
-	struct kvm *kvm = (struct kvm *)s->private;
+	struct kvm *kvm = s->private;
 	struct vgic_state_iter *iter;
 
 	/*
@@ -229,8 +229,8 @@ static void print_irq_state(struct seq_file *s, struct vgic_irq *irq,
 
 static int vgic_debug_show(struct seq_file *s, void *v)
 {
-	struct kvm *kvm = (struct kvm *)s->private;
-	struct vgic_state_iter *iter = (struct vgic_state_iter *)v;
+	struct kvm *kvm = s->private;
+	struct vgic_state_iter *iter = v;
 	struct vgic_irq *irq;
 	struct kvm_vcpu *vcpu = NULL;
 	unsigned long flags;
diff --git a/arch/arm64/kvm/vgic/vgic-init.c b/arch/arm64/kvm/vgic/vgic-init.c
index 0a06d0648970..f6d4f4052555 100644
--- a/arch/arm64/kvm/vgic/vgic-init.c
+++ b/arch/arm64/kvm/vgic/vgic-init.c
@@ -70,8 +70,9 @@ void kvm_vgic_early_init(struct kvm *kvm)
  */
 int kvm_vgic_create(struct kvm *kvm, u32 type)
 {
-	int i, ret;
 	struct kvm_vcpu *vcpu;
+	unsigned long i;
+	int ret;
 
 	if (irqchip_in_kernel(kvm))
 		return -EEXIST;
@@ -91,17 +92,17 @@ int kvm_vgic_create(struct kvm *kvm, u32 type)
 		return ret;
 
 	kvm_for_each_vcpu(i, vcpu, kvm) {
-		if (vcpu->arch.has_run_once)
+		if (vcpu_has_run_once(vcpu))
 			goto out_unlock;
 	}
 	ret = 0;
 
 	if (type == KVM_DEV_TYPE_ARM_VGIC_V2)
-		kvm->arch.max_vcpus = VGIC_V2_MAX_CPUS;
+		kvm->max_vcpus = VGIC_V2_MAX_CPUS;
 	else
-		kvm->arch.max_vcpus = VGIC_V3_MAX_CPUS;
+		kvm->max_vcpus = VGIC_V3_MAX_CPUS;
 
-	if (atomic_read(&kvm->online_vcpus) > kvm->arch.max_vcpus) {
+	if (atomic_read(&kvm->online_vcpus) > kvm->max_vcpus) {
 		ret = -E2BIG;
 		goto out_unlock;
 	}
@@ -255,7 +256,8 @@ int vgic_init(struct kvm *kvm)
 {
 	struct vgic_dist *dist = &kvm->arch.vgic;
 	struct kvm_vcpu *vcpu;
-	int ret = 0, i, idx;
+	int ret = 0, i;
+	unsigned long idx;
 
 	if (vgic_initialized(kvm))
 		return 0;
@@ -308,7 +310,7 @@ int vgic_init(struct kvm *kvm)
 			goto out;
 	}
 
-	kvm_for_each_vcpu(i, vcpu, kvm)
+	kvm_for_each_vcpu(idx, vcpu, kvm)
 		kvm_vgic_vcpu_enable(vcpu);
 
 	ret = kvm_vgic_setup_default_irq_routing(kvm);
@@ -317,7 +319,12 @@ int vgic_init(struct kvm *kvm)
 
 	vgic_debug_init(kvm);
 
-	dist->implementation_rev = 2;
+	/*
+	 * If userspace didn't set the GIC implementation revision,
+	 * default to the latest and greatest. You know want it.
+	 */
+	if (!dist->implementation_rev)
+		dist->implementation_rev = KVM_VGIC_IMP_REV_LATEST;
 	dist->initialized = true;
 
 out:
@@ -370,7 +377,7 @@ void kvm_vgic_vcpu_destroy(struct kvm_vcpu *vcpu)
 static void __kvm_vgic_destroy(struct kvm *kvm)
 {
 	struct kvm_vcpu *vcpu;
-	int i;
+	unsigned long i;
 
 	vgic_debug_destroy(kvm);
 
diff --git a/arch/arm64/kvm/vgic/vgic-its.c b/arch/arm64/kvm/vgic/vgic-its.c
index 089fc2ffcb43..733b53055f97 100644
--- a/arch/arm64/kvm/vgic/vgic-its.c
+++ b/arch/arm64/kvm/vgic/vgic-its.c
@@ -406,7 +406,7 @@ static void update_affinity_collection(struct kvm *kvm, struct vgic_its *its,
 	struct its_ite *ite;
 
 	for_each_lpi_its(device, ite, its) {
-		if (!ite->collection || coll != ite->collection)
+		if (ite->collection != coll)
 			continue;
 
 		update_affinity_ite(kvm, ite);
@@ -683,7 +683,7 @@ int vgic_its_resolve_lpi(struct kvm *kvm, struct vgic_its *its,
 	if (!vcpu)
 		return E_ITS_INT_UNMAPPED_INTERRUPT;
 
-	if (!vcpu->arch.vgic_cpu.lpis_enabled)
+	if (!vgic_lpis_enabled(vcpu))
 		return -EBUSY;
 
 	vgic_its_cache_translation(kvm, its, devid, eventid, ite->irq);
@@ -894,6 +894,18 @@ static int vgic_its_cmd_handle_movi(struct kvm *kvm, struct vgic_its *its,
 	return update_affinity(ite->irq, vcpu);
 }
 
+static bool __is_visible_gfn_locked(struct vgic_its *its, gpa_t gpa)
+{
+	gfn_t gfn = gpa >> PAGE_SHIFT;
+	int idx;
+	bool ret;
+
+	idx = srcu_read_lock(&its->dev->kvm->srcu);
+	ret = kvm_is_visible_gfn(its->dev->kvm, gfn);
+	srcu_read_unlock(&its->dev->kvm->srcu, idx);
+	return ret;
+}
+
 /*
  * Check whether an ID can be stored into the corresponding guest table.
  * For a direct table this is pretty easy, but gets a bit nasty for
@@ -908,9 +920,7 @@ static bool vgic_its_check_id(struct vgic_its *its, u64 baser, u32 id,
 	u64 indirect_ptr, type = GITS_BASER_TYPE(baser);
 	phys_addr_t base = GITS_BASER_ADDR_48_to_52(baser);
 	int esz = GITS_BASER_ENTRY_SIZE(baser);
-	int index, idx;
-	gfn_t gfn;
-	bool ret;
+	int index;
 
 	switch (type) {
 	case GITS_BASER_TYPE_DEVICE:
@@ -933,12 +943,11 @@ static bool vgic_its_check_id(struct vgic_its *its, u64 baser, u32 id,
 			return false;
 
 		addr = base + id * esz;
-		gfn = addr >> PAGE_SHIFT;
 
 		if (eaddr)
 			*eaddr = addr;
 
-		goto out;
+		return __is_visible_gfn_locked(its, addr);
 	}
 
 	/* calculate and check the index into the 1st level */
@@ -964,27 +973,42 @@ static bool vgic_its_check_id(struct vgic_its *its, u64 baser, u32 id,
 	/* Find the address of the actual entry */
 	index = id % (SZ_64K / esz);
 	indirect_ptr += index * esz;
-	gfn = indirect_ptr >> PAGE_SHIFT;
 
 	if (eaddr)
 		*eaddr = indirect_ptr;
 
-out:
-	idx = srcu_read_lock(&its->dev->kvm->srcu);
-	ret = kvm_is_visible_gfn(its->dev->kvm, gfn);
-	srcu_read_unlock(&its->dev->kvm->srcu, idx);
-	return ret;
+	return __is_visible_gfn_locked(its, indirect_ptr);
+}
+
+/*
+ * Check whether an event ID can be stored in the corresponding Interrupt
+ * Translation Table, which starts at device->itt_addr.
+ */
+static bool vgic_its_check_event_id(struct vgic_its *its, struct its_device *device,
+		u32 event_id)
+{
+	const struct vgic_its_abi *abi = vgic_its_get_abi(its);
+	int ite_esz = abi->ite_esz;
+	gpa_t gpa;
+
+	/* max table size is: BIT_ULL(device->num_eventid_bits) * ite_esz */
+	if (event_id >= BIT_ULL(device->num_eventid_bits))
+		return false;
+
+	gpa = device->itt_addr + event_id * ite_esz;
+	return __is_visible_gfn_locked(its, gpa);
 }
 
+/*
+ * Add a new collection into the ITS collection table.
+ * Returns 0 on success, and a negative error value for generic errors.
+ */
 static int vgic_its_alloc_collection(struct vgic_its *its,
 				     struct its_collection **colp,
 				     u32 coll_id)
 {
 	struct its_collection *collection;
 
-	if (!vgic_its_check_id(its, its->baser_coll_table, coll_id, NULL))
-		return E_ITS_MAPC_COLLECTION_OOR;
-
 	collection = kzalloc(sizeof(*collection), GFP_KERNEL_ACCOUNT);
 	if (!collection)
 		return -ENOMEM;
@@ -1061,7 +1085,7 @@ static int vgic_its_cmd_handle_mapi(struct kvm *kvm, struct vgic_its *its,
 	if (!device)
 		return E_ITS_MAPTI_UNMAPPED_DEVICE;
 
-	if (event_id >= BIT_ULL(device->num_eventid_bits))
+	if (!vgic_its_check_event_id(its, device, event_id))
 		return E_ITS_MAPTI_ID_OOR;
 
 	if (its_cmd_get_command(its_cmd) == GITS_CMD_MAPTI)
@@ -1078,7 +1102,12 @@ static int vgic_its_cmd_handle_mapi(struct kvm *kvm, struct vgic_its *its,
 
 	collection = find_collection(its, coll_id);
 	if (!collection) {
-		int ret = vgic_its_alloc_collection(its, &collection, coll_id);
+		int ret;
+
+		if (!vgic_its_check_id(its, its->baser_coll_table, coll_id, NULL))
+			return E_ITS_MAPC_COLLECTION_OOR;
+
+		ret = vgic_its_alloc_collection(its, &collection, coll_id);
 		if (ret)
 			return ret;
 		new_coll = collection;
@@ -1233,6 +1262,10 @@ static int vgic_its_cmd_handle_mapc(struct kvm *kvm, struct vgic_its *its,
 		if (!collection) {
 			int ret;
 
+			if (!vgic_its_check_id(its, its->baser_coll_table,
+						coll_id, NULL))
+				return E_ITS_MAPC_COLLECTION_OOR;
+
 			ret = vgic_its_alloc_collection(its, &collection,
 							coll_id);
 			if (ret)
@@ -1272,6 +1305,11 @@ static int vgic_its_cmd_handle_clear(struct kvm *kvm, struct vgic_its *its,
 	return 0;
 }
 
+int vgic_its_inv_lpi(struct kvm *kvm, struct vgic_irq *irq)
+{
+	return update_lpi_config(kvm, irq, NULL, true);
+}
+
 /*
  * The INV command syncs the configuration bits from the memory table.
  * Must be called with the its_lock mutex held.
@@ -1288,7 +1326,41 @@ static int vgic_its_cmd_handle_inv(struct kvm *kvm, struct vgic_its *its,
 	if (!ite)
 		return E_ITS_INV_UNMAPPED_INTERRUPT;
 
-	return update_lpi_config(kvm, ite->irq, NULL, true);
+	return vgic_its_inv_lpi(kvm, ite->irq);
+}
+
+/**
+ * vgic_its_invall - invalidate all LPIs targetting a given vcpu
+ * @vcpu: the vcpu for which the RD is targetted by an invalidation
+ *
+ * Contrary to the INVALL command, this targets a RD instead of a
+ * collection, and we don't need to hold the its_lock, since no ITS is
+ * involved here.
+ */
+int vgic_its_invall(struct kvm_vcpu *vcpu)
+{
+	struct kvm *kvm = vcpu->kvm;
+	int irq_count, i = 0;
+	u32 *intids;
+
+	irq_count = vgic_copy_lpi_list(kvm, vcpu, &intids);
+	if (irq_count < 0)
+		return irq_count;
+
+	for (i = 0; i < irq_count; i++) {
+		struct vgic_irq *irq = vgic_get_irq(kvm, NULL, intids[i]);
+		if (!irq)
+			continue;
+		update_lpi_config(kvm, irq, vcpu, false);
+		vgic_put_irq(kvm, irq);
+	}
+
+	kfree(intids);
+
+	if (vcpu->arch.vgic_cpu.vgic_v3.its_vpe.its_vm)
+		its_invall_vpe(&vcpu->arch.vgic_cpu.vgic_v3.its_vpe);
+
+	return 0;
 }
 
 /*
@@ -1305,32 +1377,13 @@ static int vgic_its_cmd_handle_invall(struct kvm *kvm, struct vgic_its *its,
 	u32 coll_id = its_cmd_get_collection(its_cmd);
 	struct its_collection *collection;
 	struct kvm_vcpu *vcpu;
-	struct vgic_irq *irq;
-	u32 *intids;
-	int irq_count, i;
 
 	collection = find_collection(its, coll_id);
 	if (!its_is_collection_mapped(collection))
 		return E_ITS_INVALL_UNMAPPED_COLLECTION;
 
 	vcpu = kvm_get_vcpu(kvm, collection->target_addr);
-
-	irq_count = vgic_copy_lpi_list(kvm, vcpu, &intids);
-	if (irq_count < 0)
-		return irq_count;
-
-	for (i = 0; i < irq_count; i++) {
-		irq = vgic_get_irq(kvm, NULL, intids[i]);
-		if (!irq)
-			continue;
-		update_lpi_config(kvm, irq, vcpu, false);
-		vgic_put_irq(kvm, irq);
-	}
-
-	kfree(intids);
-
-	if (vcpu->arch.vgic_cpu.vgic_v3.its_vpe.its_vm)
-		its_invall_vpe(&vcpu->arch.vgic_cpu.vgic_v3.its_vpe);
+	vgic_its_invall(vcpu);
 
 	return 0;
 }
@@ -2096,7 +2149,7 @@ static int scan_its_table(struct vgic_its *its, gpa_t base, int size, u32 esz,
 
 	memset(entry, 0, esz);
 
-	while (len > 0) {
+	while (true) {
 		int next_offset;
 		size_t byte_offset;
 
@@ -2109,6 +2162,9 @@ static int scan_its_table(struct vgic_its *its, gpa_t base, int size, u32 esz,
 			return next_offset;
 
 		byte_offset = next_offset * esz;
+		if (byte_offset >= len)
+			break;
+
 		id += next_offset;
 		gpa += byte_offset;
 		len -= byte_offset;
@@ -2143,7 +2199,7 @@ static int vgic_its_save_ite(struct vgic_its *its, struct its_device *dev,
 static int vgic_its_restore_ite(struct vgic_its *its, u32 event_id,
 				void *ptr, void *opaque)
 {
-	struct its_device *dev = (struct its_device *)opaque;
+	struct its_device *dev = opaque;
 	struct its_collection *collection;
 	struct kvm *kvm = its->dev->kvm;
 	struct kvm_vcpu *vcpu = NULL;
@@ -2175,6 +2231,9 @@ static int vgic_its_restore_ite(struct vgic_its *its, u32 event_id,
 	if (!collection)
 		return -EINVAL;
 
+	if (!vgic_its_check_event_id(its, dev, event_id))
+		return -EINVAL;
+
 	ite = vgic_its_alloc_ite(dev, collection, event_id);
 	if (IS_ERR(ite))
 		return PTR_ERR(ite);
@@ -2183,8 +2242,10 @@ static int vgic_its_restore_ite(struct vgic_its *its, u32 event_id,
 		vcpu = kvm_get_vcpu(kvm, collection->target_addr);
 
 	irq = vgic_add_lpi(kvm, lpi_id, vcpu);
-	if (IS_ERR(irq))
+	if (IS_ERR(irq)) {
+		its_free_ite(kvm, ite);
 		return PTR_ERR(irq);
+	}
 	ite->irq = irq;
 
 	return offset;
@@ -2296,6 +2357,7 @@ static int vgic_its_restore_dte(struct vgic_its *its, u32 id,
 				void *ptr, void *opaque)
 {
 	struct its_device *dev;
+	u64 baser = its->baser_device_table;
 	gpa_t itt_addr;
 	u8 num_eventid_bits;
 	u64 entry = *(u64 *)ptr;
@@ -2316,6 +2378,9 @@ static int vgic_its_restore_dte(struct vgic_its *its, u32 id,
 	/* dte entry is valid */
 	offset = (entry & KVM_ITS_DTE_NEXT_MASK) >> KVM_ITS_DTE_NEXT_SHIFT;
 
+	if (!vgic_its_check_id(its, baser, id, NULL))
+		return -EINVAL;
+
 	dev = vgic_its_alloc_device(its, id, itt_addr, num_eventid_bits);
 	if (IS_ERR(dev))
 		return PTR_ERR(dev);
@@ -2445,6 +2510,9 @@ static int vgic_its_restore_device_tables(struct vgic_its *its)
 	if (ret > 0)
 		ret = 0;
 
+	if (ret < 0)
+		vgic_its_free_device_list(its->dev->kvm, its);
+
 	return ret;
 }
 
@@ -2461,6 +2529,11 @@ static int vgic_its_save_cte(struct vgic_its *its,
 	return kvm_write_guest_lock(its->dev->kvm, gpa, &val, esz);
 }
 
+/*
+ * Restore a collection entry into the ITS collection table.
+ * Return +1 on success, 0 if the entry was invalid (which should be
+ * interpreted as end-of-table), and a negative error value for generic errors.
+ */
 static int vgic_its_restore_cte(struct vgic_its *its, gpa_t gpa, int esz)
 {
 	struct its_collection *collection;
@@ -2487,6 +2560,10 @@ static int vgic_its_restore_cte(struct vgic_its *its, gpa_t gpa, int esz)
 	collection = find_collection(its, coll_id);
 	if (collection)
 		return -EEXIST;
+
+	if (!vgic_its_check_id(its, its->baser_coll_table, coll_id, NULL))
+		return -EINVAL;
+
 	ret = vgic_its_alloc_collection(its, &collection, coll_id);
 	if (ret)
 		return ret;
@@ -2566,6 +2643,9 @@ static int vgic_its_restore_collection_table(struct vgic_its *its)
 	if (ret > 0)
 		return 0;
 
+	if (ret < 0)
+		vgic_its_free_collection_list(its->dev->kvm, its);
+
 	return ret;
 }
 
@@ -2597,7 +2677,10 @@ static int vgic_its_restore_tables_v0(struct vgic_its *its)
 	if (ret)
 		return ret;
 
-	return vgic_its_restore_device_tables(its);
+	ret = vgic_its_restore_device_tables(its);
+	if (ret)
+		vgic_its_free_collection_list(its->dev->kvm, its);
+	return ret;
 }
 
 static int vgic_its_commit_v0(struct vgic_its *its)
diff --git a/arch/arm64/kvm/vgic/vgic-kvm-device.c b/arch/arm64/kvm/vgic/vgic-kvm-device.c
index 0d000d2fe8d2..edeac2380591 100644
--- a/arch/arm64/kvm/vgic/vgic-kvm-device.c
+++ b/arch/arm64/kvm/vgic/vgic-kvm-device.c
@@ -41,11 +41,42 @@ static int vgic_check_type(struct kvm *kvm, int type_needed)
 		return 0;
 }
 
+int kvm_set_legacy_vgic_v2_addr(struct kvm *kvm, struct kvm_arm_device_addr *dev_addr)
+{
+	struct vgic_dist *vgic = &kvm->arch.vgic;
+	int r;
+
+	mutex_lock(&kvm->lock);
+	switch (FIELD_GET(KVM_ARM_DEVICE_TYPE_MASK, dev_addr->id)) {
+	case KVM_VGIC_V2_ADDR_TYPE_DIST:
+		r = vgic_check_type(kvm, KVM_DEV_TYPE_ARM_VGIC_V2);
+		if (!r)
+			r = vgic_check_iorange(kvm, vgic->vgic_dist_base, dev_addr->addr,
+					       SZ_4K, KVM_VGIC_V2_DIST_SIZE);
+		if (!r)
+			vgic->vgic_dist_base = dev_addr->addr;
+		break;
+	case KVM_VGIC_V2_ADDR_TYPE_CPU:
+		r = vgic_check_type(kvm, KVM_DEV_TYPE_ARM_VGIC_V2);
+		if (!r)
+			r = vgic_check_iorange(kvm, vgic->vgic_cpu_base, dev_addr->addr,
+					       SZ_4K, KVM_VGIC_V2_CPU_SIZE);
+		if (!r)
+			vgic->vgic_cpu_base = dev_addr->addr;
+		break;
+	default:
+		r = -ENODEV;
+	}
+
+	mutex_unlock(&kvm->lock);
+
+	return r;
+}
+
 /**
  * kvm_vgic_addr - set or get vgic VM base addresses
  * @kvm:   pointer to the vm struct
- * @type:  the VGIC addr type, one of KVM_VGIC_V[23]_ADDR_TYPE_XXX
- * @addr:  pointer to address value
+ * @attr:  pointer to the attribute being retrieved/updated
  * @write: if true set the address in the VM address space, if false read the
  *          address
  *
@@ -57,15 +88,22 @@ static int vgic_check_type(struct kvm *kvm, int type_needed)
  * overlapping regions in case of a virtual GICv3 here, since we don't know
  * the number of VCPUs yet, so we defer this check to map_resources().
  */
-int kvm_vgic_addr(struct kvm *kvm, unsigned long type, u64 *addr, bool write)
+static int kvm_vgic_addr(struct kvm *kvm, struct kvm_device_attr *attr, bool write)
 {
-	int r = 0;
+	u64 __user *uaddr = (u64 __user *)attr->addr;
 	struct vgic_dist *vgic = &kvm->arch.vgic;
 	phys_addr_t *addr_ptr, alignment, size;
 	u64 undef_value = VGIC_ADDR_UNDEF;
+	u64 addr;
+	int r;
+
+	/* Reading a redistributor region addr implies getting the index */
+	if (write || attr->attr == KVM_VGIC_V3_ADDR_TYPE_REDIST_REGION)
+		if (get_user(addr, uaddr))
+			return -EFAULT;
 
 	mutex_lock(&kvm->lock);
-	switch (type) {
+	switch (attr->attr) {
 	case KVM_VGIC_V2_ADDR_TYPE_DIST:
 		r = vgic_check_type(kvm, KVM_DEV_TYPE_ARM_VGIC_V2);
 		addr_ptr = &vgic->vgic_dist_base;
@@ -91,7 +129,7 @@ int kvm_vgic_addr(struct kvm *kvm, unsigned long type, u64 *addr, bool write)
 		if (r)
 			break;
 		if (write) {
-			r = vgic_v3_set_redist_base(kvm, 0, *addr, 0);
+			r = vgic_v3_set_redist_base(kvm, 0, addr, 0);
 			goto out;
 		}
 		rdreg = list_first_entry_or_null(&vgic->rd_regions,
@@ -111,14 +149,12 @@ int kvm_vgic_addr(struct kvm *kvm, unsigned long type, u64 *addr, bool write)
 		if (r)
 			break;
 
-		index = *addr & KVM_VGIC_V3_RDIST_INDEX_MASK;
+		index = addr & KVM_VGIC_V3_RDIST_INDEX_MASK;
 
 		if (write) {
-			gpa_t base = *addr & KVM_VGIC_V3_RDIST_BASE_MASK;
-			u32 count = (*addr & KVM_VGIC_V3_RDIST_COUNT_MASK)
-					>> KVM_VGIC_V3_RDIST_COUNT_SHIFT;
-			u8 flags = (*addr & KVM_VGIC_V3_RDIST_FLAGS_MASK)
-					>> KVM_VGIC_V3_RDIST_FLAGS_SHIFT;
+			gpa_t base = addr & KVM_VGIC_V3_RDIST_BASE_MASK;
+			u32 count = FIELD_GET(KVM_VGIC_V3_RDIST_COUNT_MASK, addr);
+			u8 flags = FIELD_GET(KVM_VGIC_V3_RDIST_FLAGS_MASK, addr);
 
 			if (!count || flags)
 				r = -EINVAL;
@@ -134,9 +170,9 @@ int kvm_vgic_addr(struct kvm *kvm, unsigned long type, u64 *addr, bool write)
 			goto out;
 		}
 
-		*addr = index;
-		*addr |= rdreg->base;
-		*addr |= (u64)rdreg->count << KVM_VGIC_V3_RDIST_COUNT_SHIFT;
+		addr = index;
+		addr |= rdreg->base;
+		addr |= (u64)rdreg->count << KVM_VGIC_V3_RDIST_COUNT_SHIFT;
 		goto out;
 	}
 	default:
@@ -147,15 +183,19 @@ int kvm_vgic_addr(struct kvm *kvm, unsigned long type, u64 *addr, bool write)
 		goto out;
 
 	if (write) {
-		r = vgic_check_iorange(kvm, *addr_ptr, *addr, alignment, size);
+		r = vgic_check_iorange(kvm, *addr_ptr, addr, alignment, size);
 		if (!r)
-			*addr_ptr = *addr;
+			*addr_ptr = addr;
 	} else {
-		*addr = *addr_ptr;
+		addr = *addr_ptr;
 	}
 
 out:
 	mutex_unlock(&kvm->lock);
+
+	if (!r && !write)
+		r =  put_user(addr, uaddr);
+
 	return r;
 }
 
@@ -165,17 +205,9 @@ static int vgic_set_common_attr(struct kvm_device *dev,
 	int r;
 
 	switch (attr->group) {
-	case KVM_DEV_ARM_VGIC_GRP_ADDR: {
-		u64 __user *uaddr = (u64 __user *)(long)attr->addr;
-		u64 addr;
-		unsigned long type = (unsigned long)attr->attr;
-
-		if (copy_from_user(&addr, uaddr, sizeof(addr)))
-			return -EFAULT;
-
-		r = kvm_vgic_addr(dev->kvm, type, &addr, true);
+	case KVM_DEV_ARM_VGIC_GRP_ADDR:
+		r = kvm_vgic_addr(dev->kvm, attr, true);
 		return (r == -ENODEV) ? -ENXIO : r;
-	}
 	case KVM_DEV_ARM_VGIC_GRP_NR_IRQS: {
 		u32 __user *uaddr = (u32 __user *)(long)attr->addr;
 		u32 val;
@@ -214,6 +246,24 @@ static int vgic_set_common_attr(struct kvm_device *dev,
 			r = vgic_init(dev->kvm);
 			mutex_unlock(&dev->kvm->lock);
 			return r;
+		case KVM_DEV_ARM_VGIC_SAVE_PENDING_TABLES:
+			/*
+			 * OK, this one isn't common at all, but we
+			 * want to handle all control group attributes
+			 * in a single place.
+			 */
+			if (vgic_check_type(dev->kvm, KVM_DEV_TYPE_ARM_VGIC_V3))
+				return -ENXIO;
+			mutex_lock(&dev->kvm->lock);
+
+			if (!lock_all_vcpus(dev->kvm)) {
+				mutex_unlock(&dev->kvm->lock);
+				return -EBUSY;
+			}
+			r = vgic_v3_save_pending_tables(dev->kvm);
+			unlock_all_vcpus(dev->kvm);
+			mutex_unlock(&dev->kvm->lock);
+			return r;
 		}
 		break;
 	}
@@ -228,22 +278,9 @@ static int vgic_get_common_attr(struct kvm_device *dev,
 	int r = -ENXIO;
 
 	switch (attr->group) {
-	case KVM_DEV_ARM_VGIC_GRP_ADDR: {
-		u64 __user *uaddr = (u64 __user *)(long)attr->addr;
-		u64 addr;
-		unsigned long type = (unsigned long)attr->attr;
-
-		if (copy_from_user(&addr, uaddr, sizeof(addr)))
-			return -EFAULT;
-
-		r = kvm_vgic_addr(dev->kvm, type, &addr, false);
-		if (r)
-			return (r == -ENODEV) ? -ENXIO : r;
-
-		if (copy_to_user(uaddr, &addr, sizeof(addr)))
-			return -EFAULT;
-		break;
-	}
+	case KVM_DEV_ARM_VGIC_GRP_ADDR:
+		r = kvm_vgic_addr(dev->kvm, attr, false);
+		return (r == -ENODEV) ? -ENXIO : r;
 	case KVM_DEV_ARM_VGIC_GRP_NR_IRQS: {
 		u32 __user *uaddr = (u32 __user *)(long)attr->addr;
 
@@ -325,7 +362,7 @@ void unlock_all_vcpus(struct kvm *kvm)
 bool lock_all_vcpus(struct kvm *kvm)
 {
 	struct kvm_vcpu *tmp_vcpu;
-	int c;
+	unsigned long c;
 
 	/*
 	 * Any time a vcpu is run, vcpu_load is called which tries to grab the
@@ -348,17 +385,18 @@ bool lock_all_vcpus(struct kvm *kvm)
  *
  * @dev:      kvm device handle
  * @attr:     kvm device attribute
- * @reg:      address the value is read or written
  * @is_write: true if userspace is writing a register
  */
 static int vgic_v2_attr_regs_access(struct kvm_device *dev,
 				    struct kvm_device_attr *attr,
-				    u32 *reg, bool is_write)
+				    bool is_write)
 {
+	u32 __user *uaddr = (u32 __user *)(unsigned long)attr->addr;
 	struct vgic_reg_attr reg_attr;
 	gpa_t addr;
 	struct kvm_vcpu *vcpu;
 	int ret;
+	u32 val;
 
 	ret = vgic_v2_parse_attr(dev, attr, &reg_attr);
 	if (ret)
@@ -367,6 +405,10 @@ static int vgic_v2_attr_regs_access(struct kvm_device *dev,
 	vcpu = reg_attr.vcpu;
 	addr = reg_attr.addr;
 
+	if (is_write)
+		if (get_user(val, uaddr))
+			return -EFAULT;
+
 	mutex_lock(&dev->kvm->lock);
 
 	ret = vgic_init(dev->kvm);
@@ -380,10 +422,10 @@ static int vgic_v2_attr_regs_access(struct kvm_device *dev,
 
 	switch (attr->group) {
 	case KVM_DEV_ARM_VGIC_GRP_CPU_REGS:
-		ret = vgic_v2_cpuif_uaccess(vcpu, is_write, addr, reg);
+		ret = vgic_v2_cpuif_uaccess(vcpu, is_write, addr, &val);
 		break;
 	case KVM_DEV_ARM_VGIC_GRP_DIST_REGS:
-		ret = vgic_v2_dist_uaccess(vcpu, is_write, addr, reg);
+		ret = vgic_v2_dist_uaccess(vcpu, is_write, addr, &val);
 		break;
 	default:
 		ret = -EINVAL;
@@ -393,57 +435,35 @@ static int vgic_v2_attr_regs_access(struct kvm_device *dev,
 	unlock_all_vcpus(dev->kvm);
 out:
 	mutex_unlock(&dev->kvm->lock);
+
+	if (!ret && !is_write)
+		ret = put_user(val, uaddr);
+
 	return ret;
 }
 
 static int vgic_v2_set_attr(struct kvm_device *dev,
 			    struct kvm_device_attr *attr)
 {
-	int ret;
-
-	ret = vgic_set_common_attr(dev, attr);
-	if (ret != -ENXIO)
-		return ret;
-
 	switch (attr->group) {
 	case KVM_DEV_ARM_VGIC_GRP_DIST_REGS:
-	case KVM_DEV_ARM_VGIC_GRP_CPU_REGS: {
-		u32 __user *uaddr = (u32 __user *)(long)attr->addr;
-		u32 reg;
-
-		if (get_user(reg, uaddr))
-			return -EFAULT;
-
-		return vgic_v2_attr_regs_access(dev, attr, &reg, true);
-	}
+	case KVM_DEV_ARM_VGIC_GRP_CPU_REGS:
+		return vgic_v2_attr_regs_access(dev, attr, true);
+	default:
+		return vgic_set_common_attr(dev, attr);
 	}
-
-	return -ENXIO;
 }
 
 static int vgic_v2_get_attr(struct kvm_device *dev,
 			    struct kvm_device_attr *attr)
 {
-	int ret;
-
-	ret = vgic_get_common_attr(dev, attr);
-	if (ret != -ENXIO)
-		return ret;
-
 	switch (attr->group) {
 	case KVM_DEV_ARM_VGIC_GRP_DIST_REGS:
-	case KVM_DEV_ARM_VGIC_GRP_CPU_REGS: {
-		u32 __user *uaddr = (u32 __user *)(long)attr->addr;
-		u32 reg = 0;
-
-		ret = vgic_v2_attr_regs_access(dev, attr, &reg, false);
-		if (ret)
-			return ret;
-		return put_user(reg, uaddr);
-	}
+	case KVM_DEV_ARM_VGIC_GRP_CPU_REGS:
+		return vgic_v2_attr_regs_access(dev, attr, false);
+	default:
+		return vgic_get_common_attr(dev, attr);
 	}
-
-	return -ENXIO;
 }
 
 static int vgic_v2_has_attr(struct kvm_device *dev,
@@ -512,18 +532,18 @@ int vgic_v3_parse_attr(struct kvm_device *dev, struct kvm_device_attr *attr,
  *
  * @dev:      kvm device handle
  * @attr:     kvm device attribute
- * @reg:      address the value is read or written
  * @is_write: true if userspace is writing a register
  */
 static int vgic_v3_attr_regs_access(struct kvm_device *dev,
 				    struct kvm_device_attr *attr,
-				    u64 *reg, bool is_write)
+				    bool is_write)
 {
 	struct vgic_reg_attr reg_attr;
 	gpa_t addr;
 	struct kvm_vcpu *vcpu;
+	bool uaccess;
+	u32 val;
 	int ret;
-	u32 tmp32;
 
 	ret = vgic_v3_parse_attr(dev, attr, &reg_attr);
 	if (ret)
@@ -532,6 +552,21 @@ static int vgic_v3_attr_regs_access(struct kvm_device *dev,
 	vcpu = reg_attr.vcpu;
 	addr = reg_attr.addr;
 
+	switch (attr->group) {
+	case KVM_DEV_ARM_VGIC_GRP_CPU_SYSREGS:
+		/* Sysregs uaccess is performed by the sysreg handling code */
+		uaccess = false;
+		break;
+	default:
+		uaccess = true;
+	}
+
+	if (uaccess && is_write) {
+		u32 __user *uaddr = (u32 __user *)(unsigned long)attr->addr;
+		if (get_user(val, uaddr))
+			return -EFAULT;
+	}
+
 	mutex_lock(&dev->kvm->lock);
 
 	if (unlikely(!vgic_initialized(dev->kvm))) {
@@ -546,29 +581,14 @@ static int vgic_v3_attr_regs_access(struct kvm_device *dev,
 
 	switch (attr->group) {
 	case KVM_DEV_ARM_VGIC_GRP_DIST_REGS:
-		if (is_write)
-			tmp32 = *reg;
-
-		ret = vgic_v3_dist_uaccess(vcpu, is_write, addr, &tmp32);
-		if (!is_write)
-			*reg = tmp32;
+		ret = vgic_v3_dist_uaccess(vcpu, is_write, addr, &val);
 		break;
 	case KVM_DEV_ARM_VGIC_GRP_REDIST_REGS:
-		if (is_write)
-			tmp32 = *reg;
-
-		ret = vgic_v3_redist_uaccess(vcpu, is_write, addr, &tmp32);
-		if (!is_write)
-			*reg = tmp32;
+		ret = vgic_v3_redist_uaccess(vcpu, is_write, addr, &val);
 		break;
-	case KVM_DEV_ARM_VGIC_GRP_CPU_SYSREGS: {
-		u64 regid;
-
-		regid = (attr->attr & KVM_DEV_ARM_VGIC_SYSREG_INSTR_MASK);
-		ret = vgic_v3_cpu_sysregs_uaccess(vcpu, is_write,
-						  regid, reg);
+	case KVM_DEV_ARM_VGIC_GRP_CPU_SYSREGS:
+		ret = vgic_v3_cpu_sysregs_uaccess(vcpu, attr, is_write);
 		break;
-	}
 	case KVM_DEV_ARM_VGIC_GRP_LEVEL_INFO: {
 		unsigned int info, intid;
 
@@ -578,7 +598,7 @@ static int vgic_v3_attr_regs_access(struct kvm_device *dev,
 			intid = attr->attr &
 				KVM_DEV_ARM_VGIC_LINE_LEVEL_INTID_MASK;
 			ret = vgic_v3_line_level_info_uaccess(vcpu, is_write,
-							      intid, reg);
+							      intid, &val);
 		} else {
 			ret = -EINVAL;
 		}
@@ -592,117 +612,41 @@ static int vgic_v3_attr_regs_access(struct kvm_device *dev,
 	unlock_all_vcpus(dev->kvm);
 out:
 	mutex_unlock(&dev->kvm->lock);
+
+	if (!ret && uaccess && !is_write) {
+		u32 __user *uaddr = (u32 __user *)(unsigned long)attr->addr;
+		ret = put_user(val, uaddr);
+	}
+
 	return ret;
 }
 
 static int vgic_v3_set_attr(struct kvm_device *dev,
 			    struct kvm_device_attr *attr)
 {
-	int ret;
-
-	ret = vgic_set_common_attr(dev, attr);
-	if (ret != -ENXIO)
-		return ret;
-
 	switch (attr->group) {
 	case KVM_DEV_ARM_VGIC_GRP_DIST_REGS:
-	case KVM_DEV_ARM_VGIC_GRP_REDIST_REGS: {
-		u32 __user *uaddr = (u32 __user *)(long)attr->addr;
-		u32 tmp32;
-		u64 reg;
-
-		if (get_user(tmp32, uaddr))
-			return -EFAULT;
-
-		reg = tmp32;
-		return vgic_v3_attr_regs_access(dev, attr, &reg, true);
-	}
-	case KVM_DEV_ARM_VGIC_GRP_CPU_SYSREGS: {
-		u64 __user *uaddr = (u64 __user *)(long)attr->addr;
-		u64 reg;
-
-		if (get_user(reg, uaddr))
-			return -EFAULT;
-
-		return vgic_v3_attr_regs_access(dev, attr, &reg, true);
-	}
-	case KVM_DEV_ARM_VGIC_GRP_LEVEL_INFO: {
-		u32 __user *uaddr = (u32 __user *)(long)attr->addr;
-		u64 reg;
-		u32 tmp32;
-
-		if (get_user(tmp32, uaddr))
-			return -EFAULT;
-
-		reg = tmp32;
-		return vgic_v3_attr_regs_access(dev, attr, &reg, true);
-	}
-	case KVM_DEV_ARM_VGIC_GRP_CTRL: {
-		int ret;
-
-		switch (attr->attr) {
-		case KVM_DEV_ARM_VGIC_SAVE_PENDING_TABLES:
-			mutex_lock(&dev->kvm->lock);
-
-			if (!lock_all_vcpus(dev->kvm)) {
-				mutex_unlock(&dev->kvm->lock);
-				return -EBUSY;
-			}
-			ret = vgic_v3_save_pending_tables(dev->kvm);
-			unlock_all_vcpus(dev->kvm);
-			mutex_unlock(&dev->kvm->lock);
-			return ret;
-		}
-		break;
-	}
+	case KVM_DEV_ARM_VGIC_GRP_REDIST_REGS:
+	case KVM_DEV_ARM_VGIC_GRP_CPU_SYSREGS:
+	case KVM_DEV_ARM_VGIC_GRP_LEVEL_INFO:
+		return vgic_v3_attr_regs_access(dev, attr, true);
+	default:
+		return vgic_set_common_attr(dev, attr);
 	}
-	return -ENXIO;
 }
 
 static int vgic_v3_get_attr(struct kvm_device *dev,
 			    struct kvm_device_attr *attr)
 {
-	int ret;
-
-	ret = vgic_get_common_attr(dev, attr);
-	if (ret != -ENXIO)
-		return ret;
-
 	switch (attr->group) {
 	case KVM_DEV_ARM_VGIC_GRP_DIST_REGS:
-	case KVM_DEV_ARM_VGIC_GRP_REDIST_REGS: {
-		u32 __user *uaddr = (u32 __user *)(long)attr->addr;
-		u64 reg;
-		u32 tmp32;
-
-		ret = vgic_v3_attr_regs_access(dev, attr, &reg, false);
-		if (ret)
-			return ret;
-		tmp32 = reg;
-		return put_user(tmp32, uaddr);
-	}
-	case KVM_DEV_ARM_VGIC_GRP_CPU_SYSREGS: {
-		u64 __user *uaddr = (u64 __user *)(long)attr->addr;
-		u64 reg;
-
-		ret = vgic_v3_attr_regs_access(dev, attr, &reg, false);
-		if (ret)
-			return ret;
-		return put_user(reg, uaddr);
-	}
-	case KVM_DEV_ARM_VGIC_GRP_LEVEL_INFO: {
-		u32 __user *uaddr = (u32 __user *)(long)attr->addr;
-		u64 reg;
-		u32 tmp32;
-
-		ret = vgic_v3_attr_regs_access(dev, attr, &reg, false);
-		if (ret)
-			return ret;
-		tmp32 = reg;
-		return put_user(tmp32, uaddr);
-	}
+	case KVM_DEV_ARM_VGIC_GRP_REDIST_REGS:
+	case KVM_DEV_ARM_VGIC_GRP_CPU_SYSREGS:
+	case KVM_DEV_ARM_VGIC_GRP_LEVEL_INFO:
+		return vgic_v3_attr_regs_access(dev, attr, false);
+	default:
+		return vgic_get_common_attr(dev, attr);
 	}
-	return -ENXIO;
 }
 
 static int vgic_v3_has_attr(struct kvm_device *dev,
diff --git a/arch/arm64/kvm/vgic/vgic-mmio-v2.c b/arch/arm64/kvm/vgic/vgic-mmio-v2.c
index 5f9014ae595b..e070cda86e12 100644
--- a/arch/arm64/kvm/vgic/vgic-mmio-v2.c
+++ b/arch/arm64/kvm/vgic/vgic-mmio-v2.c
@@ -73,9 +73,13 @@ static int vgic_mmio_uaccess_write_v2_misc(struct kvm_vcpu *vcpu,
 					   gpa_t addr, unsigned int len,
 					   unsigned long val)
 {
+	struct vgic_dist *dist = &vcpu->kvm->arch.vgic;
+	u32 reg;
+
 	switch (addr & 0x0c) {
 	case GIC_DIST_IIDR:
-		if (val != vgic_mmio_read_v2_misc(vcpu, addr, len))
+		reg = vgic_mmio_read_v2_misc(vcpu, addr, len);
+		if ((reg ^ val) & ~GICD_IIDR_REVISION_MASK)
 			return -EINVAL;
 
 		/*
@@ -87,8 +91,16 @@ static int vgic_mmio_uaccess_write_v2_misc(struct kvm_vcpu *vcpu,
 		 * migration from old kernels to new kernels with legacy
 		 * userspace.
 		 */
-		vcpu->kvm->arch.vgic.v2_groups_user_writable = true;
-		return 0;
+		reg = FIELD_GET(GICD_IIDR_REVISION_MASK, reg);
+		switch (reg) {
+		case KVM_VGIC_IMP_REV_2:
+		case KVM_VGIC_IMP_REV_3:
+			vcpu->kvm->arch.vgic.v2_groups_user_writable = true;
+			dist->implementation_rev = reg;
+			return 0;
+		default:
+			return -EINVAL;
+		}
 	}
 
 	vgic_mmio_write_v2_misc(vcpu, addr, len, val);
@@ -113,9 +125,8 @@ static void vgic_mmio_write_sgir(struct kvm_vcpu *source_vcpu,
 	int intid = val & 0xf;
 	int targets = (val >> 16) & 0xff;
 	int mode = (val >> 24) & 0x03;
-	int c;
 	struct kvm_vcpu *vcpu;
-	unsigned long flags;
+	unsigned long flags, c;
 
 	switch (mode) {
 	case 0x0:		/* as specified by targets */
@@ -418,11 +429,11 @@ static const struct vgic_register_region vgic_v2_dist_registers[] = {
 		VGIC_ACCESS_32bit),
 	REGISTER_DESC_WITH_BITS_PER_IRQ(GIC_DIST_PENDING_SET,
 		vgic_mmio_read_pending, vgic_mmio_write_spending,
-		NULL, vgic_uaccess_write_spending, 1,
+		vgic_uaccess_read_pending, vgic_uaccess_write_spending, 1,
 		VGIC_ACCESS_32bit),
 	REGISTER_DESC_WITH_BITS_PER_IRQ(GIC_DIST_PENDING_CLEAR,
 		vgic_mmio_read_pending, vgic_mmio_write_cpending,
-		NULL, vgic_uaccess_write_cpending, 1,
+		vgic_uaccess_read_pending, vgic_uaccess_write_cpending, 1,
 		VGIC_ACCESS_32bit),
 	REGISTER_DESC_WITH_BITS_PER_IRQ(GIC_DIST_ACTIVE_SET,
 		vgic_mmio_read_active, vgic_mmio_write_sactive,
diff --git a/arch/arm64/kvm/vgic/vgic-mmio-v3.c b/arch/arm64/kvm/vgic/vgic-mmio-v3.c
index bf7ec4a78497..91201f743033 100644
--- a/arch/arm64/kvm/vgic/vgic-mmio-v3.c
+++ b/arch/arm64/kvm/vgic/vgic-mmio-v3.c
@@ -155,13 +155,27 @@ static int vgic_mmio_uaccess_write_v3_misc(struct kvm_vcpu *vcpu,
 					   unsigned long val)
 {
 	struct vgic_dist *dist = &vcpu->kvm->arch.vgic;
+	u32 reg;
 
 	switch (addr & 0x0c) {
 	case GICD_TYPER2:
-	case GICD_IIDR:
 		if (val != vgic_mmio_read_v3_misc(vcpu, addr, len))
 			return -EINVAL;
 		return 0;
+	case GICD_IIDR:
+		reg = vgic_mmio_read_v3_misc(vcpu, addr, len);
+		if ((reg ^ val) & ~GICD_IIDR_REVISION_MASK)
+			return -EINVAL;
+
+		reg = FIELD_GET(GICD_IIDR_REVISION_MASK, reg);
+		switch (reg) {
+		case KVM_VGIC_IMP_REV_2:
+		case KVM_VGIC_IMP_REV_3:
+			dist->implementation_rev = reg;
+			return 0;
+		default:
+			return -EINVAL;
+		}
 	case GICD_CTLR:
 		/* Not a GICv4.1? No HW SGIs */
 		if (!kvm_vgic_global_state.has_gicv4_1)
@@ -221,34 +235,58 @@ static void vgic_mmio_write_irouter(struct kvm_vcpu *vcpu,
 	vgic_put_irq(vcpu->kvm, irq);
 }
 
+bool vgic_lpis_enabled(struct kvm_vcpu *vcpu)
+{
+	struct vgic_cpu *vgic_cpu = &vcpu->arch.vgic_cpu;
+
+	return atomic_read(&vgic_cpu->ctlr) == GICR_CTLR_ENABLE_LPIS;
+}
+
 static unsigned long vgic_mmio_read_v3r_ctlr(struct kvm_vcpu *vcpu,
 					     gpa_t addr, unsigned int len)
 {
 	struct vgic_cpu *vgic_cpu = &vcpu->arch.vgic_cpu;
+	unsigned long val;
 
-	return vgic_cpu->lpis_enabled ? GICR_CTLR_ENABLE_LPIS : 0;
-}
+	val = atomic_read(&vgic_cpu->ctlr);
+	if (vgic_get_implementation_rev(vcpu) >= KVM_VGIC_IMP_REV_3)
+		val |= GICR_CTLR_IR | GICR_CTLR_CES;
 
+	return val;
+}
 
 static void vgic_mmio_write_v3r_ctlr(struct kvm_vcpu *vcpu,
 				     gpa_t addr, unsigned int len,
 				     unsigned long val)
 {
 	struct vgic_cpu *vgic_cpu = &vcpu->arch.vgic_cpu;
-	bool was_enabled = vgic_cpu->lpis_enabled;
+	u32 ctlr;
 
 	if (!vgic_has_its(vcpu->kvm))
 		return;
 
-	vgic_cpu->lpis_enabled = val & GICR_CTLR_ENABLE_LPIS;
+	if (!(val & GICR_CTLR_ENABLE_LPIS)) {
+		/*
+		 * Don't disable if RWP is set, as there already an
+		 * ongoing disable. Funky guest...
+		 */
+		ctlr = atomic_cmpxchg_acquire(&vgic_cpu->ctlr,
+					      GICR_CTLR_ENABLE_LPIS,
+					      GICR_CTLR_RWP);
+		if (ctlr != GICR_CTLR_ENABLE_LPIS)
+			return;
 
-	if (was_enabled && !vgic_cpu->lpis_enabled) {
 		vgic_flush_pending_lpis(vcpu);
 		vgic_its_invalidate_cache(vcpu->kvm);
-	}
+		atomic_set_release(&vgic_cpu->ctlr, 0);
+	} else {
+		ctlr = atomic_cmpxchg_acquire(&vgic_cpu->ctlr, 0,
+					      GICR_CTLR_ENABLE_LPIS);
+		if (ctlr != 0)
+			return;
 
-	if (!was_enabled && vgic_cpu->lpis_enabled)
 		vgic_enable_lpis(vcpu);
+	}
 }
 
 static bool vgic_mmio_vcpu_rdist_is_last(struct kvm_vcpu *vcpu)
@@ -315,42 +353,6 @@ static unsigned long vgic_mmio_read_v3_idregs(struct kvm_vcpu *vcpu,
 	return 0;
 }
 
-static unsigned long vgic_v3_uaccess_read_pending(struct kvm_vcpu *vcpu,
-						  gpa_t addr, unsigned int len)
-{
-	u32 intid = VGIC_ADDR_TO_INTID(addr, 1);
-	u32 value = 0;
-	int i;
-
-	/*
-	 * pending state of interrupt is latched in pending_latch variable.
-	 * Userspace will save and restore pending state and line_level
-	 * separately.
-	 * Refer to Documentation/virt/kvm/devices/arm-vgic-v3.rst
-	 * for handling of ISPENDR and ICPENDR.
-	 */
-	for (i = 0; i < len * 8; i++) {
-		struct vgic_irq *irq = vgic_get_irq(vcpu->kvm, vcpu, intid + i);
-		bool state = irq->pending_latch;
-
-		if (irq->hw && vgic_irq_is_sgi(irq->intid)) {
-			int err;
-
-			err = irq_get_irqchip_state(irq->host_irq,
-						    IRQCHIP_STATE_PENDING,
-						    &state);
-			WARN_ON(err);
-		}
-
-		if (state)
-			value |= (1U << i);
-
-		vgic_put_irq(vcpu->kvm, irq);
-	}
-
-	return value;
-}
-
 static int vgic_v3_uaccess_write_pending(struct kvm_vcpu *vcpu,
 					 gpa_t addr, unsigned int len,
 					 unsigned long val)
@@ -478,11 +480,10 @@ static void vgic_mmio_write_propbase(struct kvm_vcpu *vcpu,
 				     unsigned long val)
 {
 	struct vgic_dist *dist = &vcpu->kvm->arch.vgic;
-	struct vgic_cpu *vgic_cpu = &vcpu->arch.vgic_cpu;
 	u64 old_propbaser, propbaser;
 
 	/* Storing a value with LPIs already enabled is undefined */
-	if (vgic_cpu->lpis_enabled)
+	if (vgic_lpis_enabled(vcpu))
 		return;
 
 	do {
@@ -513,7 +514,7 @@ static void vgic_mmio_write_pendbase(struct kvm_vcpu *vcpu,
 	u64 old_pendbaser, pendbaser;
 
 	/* Storing a value with LPIs already enabled is undefined */
-	if (vgic_cpu->lpis_enabled)
+	if (vgic_lpis_enabled(vcpu))
 		return;
 
 	do {
@@ -525,6 +526,63 @@ static void vgic_mmio_write_pendbase(struct kvm_vcpu *vcpu,
 			   pendbaser) != old_pendbaser);
 }
 
+static unsigned long vgic_mmio_read_sync(struct kvm_vcpu *vcpu,
+					 gpa_t addr, unsigned int len)
+{
+	return !!atomic_read(&vcpu->arch.vgic_cpu.syncr_busy);
+}
+
+static void vgic_set_rdist_busy(struct kvm_vcpu *vcpu, bool busy)
+{
+	if (busy) {
+		atomic_inc(&vcpu->arch.vgic_cpu.syncr_busy);
+		smp_mb__after_atomic();
+	} else {
+		smp_mb__before_atomic();
+		atomic_dec(&vcpu->arch.vgic_cpu.syncr_busy);
+	}
+}
+
+static void vgic_mmio_write_invlpi(struct kvm_vcpu *vcpu,
+				   gpa_t addr, unsigned int len,
+				   unsigned long val)
+{
+	struct vgic_irq *irq;
+
+	/*
+	 * If the guest wrote only to the upper 32bit part of the
+	 * register, drop the write on the floor, as it is only for
+	 * vPEs (which we don't support for obvious reasons).
+	 *
+	 * Also discard the access if LPIs are not enabled.
+	 */
+	if ((addr & 4) || !vgic_lpis_enabled(vcpu))
+		return;
+
+	vgic_set_rdist_busy(vcpu, true);
+
+	irq = vgic_get_irq(vcpu->kvm, NULL, lower_32_bits(val));
+	if (irq) {
+		vgic_its_inv_lpi(vcpu->kvm, irq);
+		vgic_put_irq(vcpu->kvm, irq);
+	}
+
+	vgic_set_rdist_busy(vcpu, false);
+}
+
+static void vgic_mmio_write_invall(struct kvm_vcpu *vcpu,
+				   gpa_t addr, unsigned int len,
+				   unsigned long val)
+{
+	/* See vgic_mmio_write_invlpi() for the early return rationale */
+	if ((addr & 4) || !vgic_lpis_enabled(vcpu))
+		return;
+
+	vgic_set_rdist_busy(vcpu, true);
+	vgic_its_invall(vcpu);
+	vgic_set_rdist_busy(vcpu, false);
+}
+
 /*
  * The GICv3 per-IRQ registers are split to control PPIs and SGIs in the
  * redistributors, while SPIs are covered by registers in the distributor
@@ -572,7 +630,7 @@ static const struct vgic_register_region vgic_v3_dist_registers[] = {
 		VGIC_ACCESS_32bit),
 	REGISTER_DESC_WITH_BITS_PER_IRQ_SHARED(GICD_ISPENDR,
 		vgic_mmio_read_pending, vgic_mmio_write_spending,
-		vgic_v3_uaccess_read_pending, vgic_v3_uaccess_write_pending, 1,
+		vgic_uaccess_read_pending, vgic_v3_uaccess_write_pending, 1,
 		VGIC_ACCESS_32bit),
 	REGISTER_DESC_WITH_BITS_PER_IRQ_SHARED(GICD_ICPENDR,
 		vgic_mmio_read_pending, vgic_mmio_write_cpending,
@@ -630,6 +688,15 @@ static const struct vgic_register_region vgic_v3_rd_registers[] = {
 	REGISTER_DESC_WITH_LENGTH(GICR_PENDBASER,
 		vgic_mmio_read_pendbase, vgic_mmio_write_pendbase, 8,
 		VGIC_ACCESS_64bit | VGIC_ACCESS_32bit),
+	REGISTER_DESC_WITH_LENGTH(GICR_INVLPIR,
+		vgic_mmio_read_raz, vgic_mmio_write_invlpi, 8,
+		VGIC_ACCESS_64bit | VGIC_ACCESS_32bit),
+	REGISTER_DESC_WITH_LENGTH(GICR_INVALLR,
+		vgic_mmio_read_raz, vgic_mmio_write_invall, 8,
+		VGIC_ACCESS_64bit | VGIC_ACCESS_32bit),
+	REGISTER_DESC_WITH_LENGTH(GICR_SYNCR,
+		vgic_mmio_read_sync, vgic_mmio_write_wi, 4,
+		VGIC_ACCESS_32bit),
 	REGISTER_DESC_WITH_LENGTH(GICR_IDREGS,
 		vgic_mmio_read_v3_idregs, vgic_mmio_write_wi, 48,
 		VGIC_ACCESS_32bit),
@@ -647,7 +714,7 @@ static const struct vgic_register_region vgic_v3_rd_registers[] = {
 		VGIC_ACCESS_32bit),
 	REGISTER_DESC_WITH_LENGTH_UACCESS(SZ_64K + GICR_ISPENDR0,
 		vgic_mmio_read_pending, vgic_mmio_write_spending,
-		vgic_v3_uaccess_read_pending, vgic_v3_uaccess_write_pending, 4,
+		vgic_uaccess_read_pending, vgic_v3_uaccess_write_pending, 4,
 		VGIC_ACCESS_32bit),
 	REGISTER_DESC_WITH_LENGTH_UACCESS(SZ_64K + GICR_ICPENDR0,
 		vgic_mmio_read_pending, vgic_mmio_write_cpending,
@@ -754,7 +821,8 @@ static void vgic_unregister_redist_iodev(struct kvm_vcpu *vcpu)
 static int vgic_register_all_redist_iodevs(struct kvm *kvm)
 {
 	struct kvm_vcpu *vcpu;
-	int c, ret = 0;
+	unsigned long c;
+	int ret = 0;
 
 	kvm_for_each_vcpu(c, vcpu, kvm) {
 		ret = vgic_register_redist_iodev(vcpu);
@@ -763,10 +831,12 @@ static int vgic_register_all_redist_iodevs(struct kvm *kvm)
 	}
 
 	if (ret) {
-		/* The current c failed, so we start with the previous one. */
+		/* The current c failed, so iterate over the previous ones. */
+		int i;
+
 		mutex_lock(&kvm->slots_lock);
-		for (c--; c >= 0; c--) {
-			vcpu = kvm_get_vcpu(kvm, c);
+		for (i = 0; i < c; i++) {
+			vcpu = kvm_get_vcpu(kvm, i);
 			vgic_unregister_redist_iodev(vcpu);
 		}
 		mutex_unlock(&kvm->slots_lock);
@@ -916,12 +986,8 @@ int vgic_v3_has_attr_regs(struct kvm_device *dev, struct kvm_device_attr *attr)
 		iodev.base_addr = 0;
 		break;
 	}
-	case KVM_DEV_ARM_VGIC_GRP_CPU_SYSREGS: {
-		u64 reg, id;
-
-		id = (attr->attr & KVM_DEV_ARM_VGIC_SYSREG_INSTR_MASK);
-		return vgic_v3_has_cpu_sysregs_attr(vcpu, 0, id, &reg);
-	}
+	case KVM_DEV_ARM_VGIC_GRP_CPU_SYSREGS:
+		return vgic_v3_has_cpu_sysregs_attr(vcpu, attr);
 	default:
 		return -ENXIO;
 	}
@@ -995,10 +1061,10 @@ void vgic_v3_dispatch_sgi(struct kvm_vcpu *vcpu, u64 reg, bool allow_group1)
 	struct kvm_vcpu *c_vcpu;
 	u16 target_cpus;
 	u64 mpidr;
-	int sgi, c;
+	int sgi;
 	int vcpu_id = vcpu->vcpu_id;
 	bool broadcast;
-	unsigned long flags;
+	unsigned long c, flags;
 
 	sgi = (reg & ICC_SGI1R_SGI_ID_MASK) >> ICC_SGI1R_SGI_ID_SHIFT;
 	broadcast = reg & BIT_ULL(ICC_SGI1R_IRQ_ROUTING_MODE_BIT);
@@ -1088,7 +1154,7 @@ int vgic_v3_redist_uaccess(struct kvm_vcpu *vcpu, bool is_write,
 }
 
 int vgic_v3_line_level_info_uaccess(struct kvm_vcpu *vcpu, bool is_write,
-				    u32 intid, u64 *val)
+				    u32 intid, u32 *val)
 {
 	if (intid % 32)
 		return -EINVAL;
diff --git a/arch/arm64/kvm/vgic/vgic-mmio.c b/arch/arm64/kvm/vgic/vgic-mmio.c
index 48c6067fc5ec..b32d434c1d4a 100644
--- a/arch/arm64/kvm/vgic/vgic-mmio.c
+++ b/arch/arm64/kvm/vgic/vgic-mmio.c
@@ -226,8 +226,9 @@ int vgic_uaccess_write_cenable(struct kvm_vcpu *vcpu,
 	return 0;
 }
 
-unsigned long vgic_mmio_read_pending(struct kvm_vcpu *vcpu,
-				     gpa_t addr, unsigned int len)
+static unsigned long __read_pending(struct kvm_vcpu *vcpu,
+				    gpa_t addr, unsigned int len,
+				    bool is_user)
 {
 	u32 intid = VGIC_ADDR_TO_INTID(addr, 1);
 	u32 value = 0;
@@ -239,6 +240,15 @@ unsigned long vgic_mmio_read_pending(struct kvm_vcpu *vcpu,
 		unsigned long flags;
 		bool val;
 
+		/*
+		 * When used from userspace with a GICv3 model:
+		 *
+		 * Pending state of interrupt is latched in pending_latch
+		 * variable.  Userspace will save and restore pending state
+		 * and line_level separately.
+		 * Refer to Documentation/virt/kvm/devices/arm-vgic-v3.rst
+		 * for handling of ISPENDR and ICPENDR.
+		 */
 		raw_spin_lock_irqsave(&irq->irq_lock, flags);
 		if (irq->hw && vgic_irq_is_sgi(irq->intid)) {
 			int err;
@@ -248,8 +258,20 @@ unsigned long vgic_mmio_read_pending(struct kvm_vcpu *vcpu,
 						    IRQCHIP_STATE_PENDING,
 						    &val);
 			WARN_RATELIMIT(err, "IRQ %d", irq->host_irq);
+		} else if (!is_user && vgic_irq_is_mapped_level(irq)) {
+			val = vgic_get_phys_line_level(irq);
 		} else {
-			val = irq_is_pending(irq);
+			switch (vcpu->kvm->arch.vgic.vgic_model) {
+			case KVM_DEV_TYPE_ARM_VGIC_V3:
+				if (is_user) {
+					val = irq->pending_latch;
+					break;
+				}
+				fallthrough;
+			default:
+				val = irq_is_pending(irq);
+				break;
+			}
 		}
 
 		value |= ((u32)val << i);
@@ -261,6 +283,18 @@ unsigned long vgic_mmio_read_pending(struct kvm_vcpu *vcpu,
 	return value;
 }
 
+unsigned long vgic_mmio_read_pending(struct kvm_vcpu *vcpu,
+				     gpa_t addr, unsigned int len)
+{
+	return __read_pending(vcpu, addr, len, false);
+}
+
+unsigned long vgic_uaccess_read_pending(struct kvm_vcpu *vcpu,
+					gpa_t addr, unsigned int len)
+{
+	return __read_pending(vcpu, addr, len, true);
+}
+
 static bool is_vgic_v2_sgi(struct kvm_vcpu *vcpu, struct vgic_irq *irq)
 {
 	return (vgic_irq_is_sgi(irq->intid) &&
@@ -741,10 +775,10 @@ void vgic_mmio_write_config(struct kvm_vcpu *vcpu,
 	}
 }
 
-u64 vgic_read_irq_line_level_info(struct kvm_vcpu *vcpu, u32 intid)
+u32 vgic_read_irq_line_level_info(struct kvm_vcpu *vcpu, u32 intid)
 {
 	int i;
-	u64 val = 0;
+	u32 val = 0;
 	int nr_irqs = vcpu->kvm->arch.vgic.nr_spis + VGIC_NR_PRIVATE_IRQS;
 
 	for (i = 0; i < 32; i++) {
@@ -764,7 +798,7 @@ u64 vgic_read_irq_line_level_info(struct kvm_vcpu *vcpu, u32 intid)
 }
 
 void vgic_write_irq_line_level_info(struct kvm_vcpu *vcpu, u32 intid,
-				    const u64 val)
+				    const u32 val)
 {
 	int i;
 	int nr_irqs = vcpu->kvm->arch.vgic.nr_spis + VGIC_NR_PRIVATE_IRQS;
@@ -1050,7 +1084,7 @@ static int dispatch_mmio_write(struct kvm_vcpu *vcpu, struct kvm_io_device *dev,
 	return 0;
 }
 
-struct kvm_io_device_ops kvm_io_gic_ops = {
+const struct kvm_io_device_ops kvm_io_gic_ops = {
 	.read = dispatch_mmio_read,
 	.write = dispatch_mmio_write,
 };
diff --git a/arch/arm64/kvm/vgic/vgic-mmio.h b/arch/arm64/kvm/vgic/vgic-mmio.h
index fefcca2b14dc..5b490a4dfa5e 100644
--- a/arch/arm64/kvm/vgic/vgic-mmio.h
+++ b/arch/arm64/kvm/vgic/vgic-mmio.h
@@ -34,7 +34,7 @@ struct vgic_register_region {
 	};
 };
 
-extern struct kvm_io_device_ops kvm_io_gic_ops;
+extern const struct kvm_io_device_ops kvm_io_gic_ops;
 
 #define VGIC_ACCESS_8bit	1
 #define VGIC_ACCESS_32bit	2
@@ -149,6 +149,9 @@ int vgic_uaccess_write_cenable(struct kvm_vcpu *vcpu,
 unsigned long vgic_mmio_read_pending(struct kvm_vcpu *vcpu,
 				     gpa_t addr, unsigned int len);
 
+unsigned long vgic_uaccess_read_pending(struct kvm_vcpu *vcpu,
+					gpa_t addr, unsigned int len);
+
 void vgic_mmio_write_spending(struct kvm_vcpu *vcpu,
 			      gpa_t addr, unsigned int len,
 			      unsigned long val);
@@ -204,10 +207,10 @@ void vgic_mmio_write_config(struct kvm_vcpu *vcpu,
 int vgic_uaccess(struct kvm_vcpu *vcpu, struct vgic_io_device *dev,
 		 bool is_write, int offset, u32 *val);
 
-u64 vgic_read_irq_line_level_info(struct kvm_vcpu *vcpu, u32 intid);
+u32 vgic_read_irq_line_level_info(struct kvm_vcpu *vcpu, u32 intid);
 
 void vgic_write_irq_line_level_info(struct kvm_vcpu *vcpu, u32 intid,
-				    const u64 val);
+				    const u32 val);
 
 unsigned int vgic_v2_init_dist_iodev(struct vgic_io_device *dev);
 
diff --git a/arch/arm64/kvm/vgic/vgic-v2.c b/arch/arm64/kvm/vgic/vgic-v2.c
index 95a18cec14a3..645648349c99 100644
--- a/arch/arm64/kvm/vgic/vgic-v2.c
+++ b/arch/arm64/kvm/vgic/vgic-v2.c
@@ -293,12 +293,12 @@ int vgic_v2_map_resources(struct kvm *kvm)
 
 	if (IS_VGIC_ADDR_UNDEF(dist->vgic_dist_base) ||
 	    IS_VGIC_ADDR_UNDEF(dist->vgic_cpu_base)) {
-		kvm_err("Need to set vgic cpu and dist addresses first\n");
+		kvm_debug("Need to set vgic cpu and dist addresses first\n");
 		return -ENXIO;
 	}
 
 	if (!vgic_v2_check_base(dist->vgic_dist_base, dist->vgic_cpu_base)) {
-		kvm_err("VGIC CPU and dist frames overlap\n");
+		kvm_debug("VGIC CPU and dist frames overlap\n");
 		return -EINVAL;
 	}
 
@@ -345,6 +345,11 @@ int vgic_v2_probe(const struct gic_kvm_info *info)
 	int ret;
 	u32 vtr;
 
+	if (is_protected_kvm_enabled()) {
+		kvm_err("GICv2 not supported in protected mode\n");
+		return -ENXIO;
+	}
+
 	if (!info->vctrl.start) {
 		kvm_err("GICH not present in the firmware table\n");
 		return -ENXIO;
diff --git a/arch/arm64/kvm/vgic/vgic-v3.c b/arch/arm64/kvm/vgic/vgic-v3.c
index 04f62c4b07fb..826ff6f2a4e7 100644
--- a/arch/arm64/kvm/vgic/vgic-v3.c
+++ b/arch/arm64/kvm/vgic/vgic-v3.c
@@ -542,24 +542,24 @@ int vgic_v3_map_resources(struct kvm *kvm)
 	struct vgic_dist *dist = &kvm->arch.vgic;
 	struct kvm_vcpu *vcpu;
 	int ret = 0;
-	int c;
+	unsigned long c;
 
 	kvm_for_each_vcpu(c, vcpu, kvm) {
 		struct vgic_cpu *vgic_cpu = &vcpu->arch.vgic_cpu;
 
 		if (IS_VGIC_ADDR_UNDEF(vgic_cpu->rd_iodev.base_addr)) {
-			kvm_debug("vcpu %d redistributor base not set\n", c);
+			kvm_debug("vcpu %ld redistributor base not set\n", c);
 			return -ENXIO;
 		}
 	}
 
 	if (IS_VGIC_ADDR_UNDEF(dist->vgic_dist_base)) {
-		kvm_err("Need to set vgic distributor addresses first\n");
+		kvm_debug("Need to set vgic distributor addresses first\n");
 		return -ENXIO;
 	}
 
 	if (!vgic_v3_check_base(kvm)) {
-		kvm_err("VGIC redist and dist frames overlap\n");
+		kvm_debug("VGIC redist and dist frames overlap\n");
 		return -EINVAL;
 	}
 
@@ -609,6 +609,22 @@ static int __init early_gicv4_enable(char *buf)
 }
 early_param("kvm-arm.vgic_v4_enable", early_gicv4_enable);
 
+static const struct midr_range broken_seis[] = {
+	MIDR_ALL_VERSIONS(MIDR_APPLE_M1_ICESTORM),
+	MIDR_ALL_VERSIONS(MIDR_APPLE_M1_FIRESTORM),
+	MIDR_ALL_VERSIONS(MIDR_APPLE_M1_ICESTORM_PRO),
+	MIDR_ALL_VERSIONS(MIDR_APPLE_M1_FIRESTORM_PRO),
+	MIDR_ALL_VERSIONS(MIDR_APPLE_M1_ICESTORM_MAX),
+	MIDR_ALL_VERSIONS(MIDR_APPLE_M1_FIRESTORM_MAX),
+	{},
+};
+
+static bool vgic_v3_broken_seis(void)
+{
+	return ((kvm_vgic_global_state.ich_vtr_el2 & ICH_VTR_SEIS_MASK) &&
+		is_midr_in_range_list(read_cpuid_id(), broken_seis));
+}
+
 /**
  * vgic_v3_probe - probe for a VGICv3 compatible interrupt controller
  * @info:	pointer to the GIC description
@@ -651,7 +667,7 @@ int vgic_v3_probe(const struct gic_kvm_info *info)
 	} else if (!PAGE_ALIGNED(info->vcpu.start)) {
 		pr_warn("GICV physical address 0x%llx not page aligned\n",
 			(unsigned long long)info->vcpu.start);
-	} else {
+	} else if (kvm_get_mode() != KVM_MODE_PROTECTED) {
 		kvm_vgic_global_state.vcpu_base = info->vcpu.start;
 		kvm_vgic_global_state.can_emulate_gicv2 = true;
 		ret = kvm_register_vgic_device(KVM_DEV_TYPE_ARM_VGIC_V2);
@@ -676,9 +692,10 @@ int vgic_v3_probe(const struct gic_kvm_info *info)
 		group1_trap = true;
 	}
 
-	if (kvm_vgic_global_state.ich_vtr_el2 & ICH_VTR_SEIS_MASK) {
-		kvm_info("GICv3 with locally generated SEI\n");
+	if (vgic_v3_broken_seis()) {
+		kvm_info("GICv3 with broken locally generated SEI\n");
 
+		kvm_vgic_global_state.ich_vtr_el2 &= ~ICH_VTR_SEIS_MASK;
 		group0_trap = true;
 		group1_trap = true;
 		if (ich_vtr_el2 & ICH_VTR_TDS_MASK)
diff --git a/arch/arm64/kvm/vgic/vgic-v4.c b/arch/arm64/kvm/vgic/vgic-v4.c
index 772dd15a22c7..ad06ba6c9b00 100644
--- a/arch/arm64/kvm/vgic/vgic-v4.c
+++ b/arch/arm64/kvm/vgic/vgic-v4.c
@@ -189,7 +189,7 @@ void vgic_v4_configure_vsgis(struct kvm *kvm)
 {
 	struct vgic_dist *dist = &kvm->arch.vgic;
 	struct kvm_vcpu *vcpu;
-	int i;
+	unsigned long i;
 
 	kvm_arm_halt_guest(kvm);
 
@@ -235,7 +235,8 @@ int vgic_v4_init(struct kvm *kvm)
 {
 	struct vgic_dist *dist = &kvm->arch.vgic;
 	struct kvm_vcpu *vcpu;
-	int i, nr_vcpus, ret;
+	int nr_vcpus, ret;
+	unsigned long i;
 
 	if (!kvm_vgic_global_state.has_gicv4)
 		return 0; /* Nothing to see here... move along. */
diff --git a/arch/arm64/kvm/vgic/vgic.c b/arch/arm64/kvm/vgic/vgic.c
index 5dad4996cfb2..d97e6080b421 100644
--- a/arch/arm64/kvm/vgic/vgic.c
+++ b/arch/arm64/kvm/vgic/vgic.c
@@ -37,7 +37,7 @@ struct vgic_global kvm_vgic_global_state __ro_after_init = {
  * If you need to take multiple locks, always take the upper lock first,
  * then the lower ones, e.g. first take the its_lock, then the irq_lock.
  * If you are already holding a lock and need to take a higher one, you
- * have to drop the lower ranking lock first and re-aquire it after having
+ * have to drop the lower ranking lock first and re-acquire it after having
  * taken the upper one.
  *
  * When taking more than one ap_list_lock at the same time, always take the
@@ -990,7 +990,7 @@ int kvm_vgic_vcpu_pending_irq(struct kvm_vcpu *vcpu)
 void vgic_kick_vcpus(struct kvm *kvm)
 {
 	struct kvm_vcpu *vcpu;
-	int c;
+	unsigned long c;
 
 	/*
 	 * We've injected an interrupt, time to find out who deserves
diff --git a/arch/arm64/kvm/vgic/vgic.h b/arch/arm64/kvm/vgic/vgic.h
index 3fd6c86a7ef3..0c8da72953f0 100644
--- a/arch/arm64/kvm/vgic/vgic.h
+++ b/arch/arm64/kvm/vgic/vgic.h
@@ -98,6 +98,11 @@
 #define DEBUG_SPINLOCK_BUG_ON(p)
 #endif
 
+static inline u32 vgic_get_implementation_rev(struct kvm_vcpu *vcpu)
+{
+	return vcpu->kvm->arch.vgic.implementation_rev;
+}
+
 /* Requires the irq_lock to be held by the caller. */
 static inline bool irq_is_pending(struct vgic_irq *irq)
 {
@@ -240,12 +245,11 @@ int vgic_v3_dist_uaccess(struct kvm_vcpu *vcpu, bool is_write,
 			 int offset, u32 *val);
 int vgic_v3_redist_uaccess(struct kvm_vcpu *vcpu, bool is_write,
 			 int offset, u32 *val);
-int vgic_v3_cpu_sysregs_uaccess(struct kvm_vcpu *vcpu, bool is_write,
-			 u64 id, u64 *val);
-int vgic_v3_has_cpu_sysregs_attr(struct kvm_vcpu *vcpu, bool is_write, u64 id,
-				u64 *reg);
+int vgic_v3_cpu_sysregs_uaccess(struct kvm_vcpu *vcpu,
+				struct kvm_device_attr *attr, bool is_write);
+int vgic_v3_has_cpu_sysregs_attr(struct kvm_vcpu *vcpu, struct kvm_device_attr *attr);
 int vgic_v3_line_level_info_uaccess(struct kvm_vcpu *vcpu, bool is_write,
-				    u32 intid, u64 *val);
+				    u32 intid, u32 *val);
 int kvm_register_vgic_device(unsigned long type);
 void vgic_set_vmcr(struct kvm_vcpu *vcpu, struct vgic_vmcr *vmcr);
 void vgic_get_vmcr(struct kvm_vcpu *vcpu, struct vgic_vmcr *vmcr);
@@ -308,6 +312,7 @@ static inline bool vgic_dist_overlap(struct kvm *kvm, gpa_t base, size_t size)
 		(base < d->vgic_dist_base + KVM_VGIC_V3_DIST_SIZE);
 }
 
+bool vgic_lpis_enabled(struct kvm_vcpu *vcpu);
 int vgic_copy_lpi_list(struct kvm *kvm, struct kvm_vcpu *vcpu, u32 **intid_ptr);
 int vgic_its_resolve_lpi(struct kvm *kvm, struct vgic_its *its,
 			 u32 devid, u32 eventid, struct vgic_irq **irq);
@@ -317,6 +322,10 @@ void vgic_lpi_translation_cache_init(struct kvm *kvm);
 void vgic_lpi_translation_cache_destroy(struct kvm *kvm);
 void vgic_its_invalidate_cache(struct kvm *kvm);
 
+/* GICv4.1 MMIO interface */
+int vgic_its_inv_lpi(struct kvm *kvm, struct vgic_irq *irq);
+int vgic_its_invall(struct kvm_vcpu *vcpu);
+
 bool vgic_supports_direct_msis(struct kvm *kvm);
 int vgic_v4_init(struct kvm *kvm);
 void vgic_v4_teardown(struct kvm *kvm);
diff --git a/arch/arm64/kvm/vmid.c b/arch/arm64/kvm/vmid.c
new file mode 100644
index 000000000000..d78ae63d7c15
--- /dev/null
+++ b/arch/arm64/kvm/vmid.c
@@ -0,0 +1,196 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * VMID allocator.
+ *
+ * Based on Arm64 ASID allocator algorithm.
+ * Please refer arch/arm64/mm/context.c for detailed
+ * comments on algorithm.
+ *
+ * Copyright (C) 2002-2003 Deep Blue Solutions Ltd, all rights reserved.
+ * Copyright (C) 2012 ARM Ltd.
+ */
+
+#include <linux/bitfield.h>
+#include <linux/bitops.h>
+
+#include <asm/kvm_asm.h>
+#include <asm/kvm_mmu.h>
+
+unsigned int kvm_arm_vmid_bits;
+static DEFINE_RAW_SPINLOCK(cpu_vmid_lock);
+
+static atomic64_t vmid_generation;
+static unsigned long *vmid_map;
+
+static DEFINE_PER_CPU(atomic64_t, active_vmids);
+static DEFINE_PER_CPU(u64, reserved_vmids);
+
+#define VMID_MASK		(~GENMASK(kvm_arm_vmid_bits - 1, 0))
+#define VMID_FIRST_VERSION	(1UL << kvm_arm_vmid_bits)
+
+#define NUM_USER_VMIDS		VMID_FIRST_VERSION
+#define vmid2idx(vmid)		((vmid) & ~VMID_MASK)
+#define idx2vmid(idx)		vmid2idx(idx)
+
+/*
+ * As vmid #0 is always reserved, we will never allocate one
+ * as below and can be treated as invalid. This is used to
+ * set the active_vmids on vCPU schedule out.
+ */
+#define VMID_ACTIVE_INVALID		VMID_FIRST_VERSION
+
+#define vmid_gen_match(vmid) \
+	(!(((vmid) ^ atomic64_read(&vmid_generation)) >> kvm_arm_vmid_bits))
+
+static void flush_context(void)
+{
+	int cpu;
+	u64 vmid;
+
+	bitmap_clear(vmid_map, 0, NUM_USER_VMIDS);
+
+	for_each_possible_cpu(cpu) {
+		vmid = atomic64_xchg_relaxed(&per_cpu(active_vmids, cpu), 0);
+
+		/* Preserve reserved VMID */
+		if (vmid == 0)
+			vmid = per_cpu(reserved_vmids, cpu);
+		__set_bit(vmid2idx(vmid), vmid_map);
+		per_cpu(reserved_vmids, cpu) = vmid;
+	}
+
+	/*
+	 * Unlike ASID allocator, we expect less frequent rollover in
+	 * case of VMIDs. Hence, instead of marking the CPU as
+	 * flush_pending and issuing a local context invalidation on
+	 * the next context-switch, we broadcast TLB flush + I-cache
+	 * invalidation over the inner shareable domain on rollover.
+	 */
+	kvm_call_hyp(__kvm_flush_vm_context);
+}
+
+static bool check_update_reserved_vmid(u64 vmid, u64 newvmid)
+{
+	int cpu;
+	bool hit = false;
+
+	/*
+	 * Iterate over the set of reserved VMIDs looking for a match
+	 * and update to use newvmid (i.e. the same VMID in the current
+	 * generation).
+	 */
+	for_each_possible_cpu(cpu) {
+		if (per_cpu(reserved_vmids, cpu) == vmid) {
+			hit = true;
+			per_cpu(reserved_vmids, cpu) = newvmid;
+		}
+	}
+
+	return hit;
+}
+
+static u64 new_vmid(struct kvm_vmid *kvm_vmid)
+{
+	static u32 cur_idx = 1;
+	u64 vmid = atomic64_read(&kvm_vmid->id);
+	u64 generation = atomic64_read(&vmid_generation);
+
+	if (vmid != 0) {
+		u64 newvmid = generation | (vmid & ~VMID_MASK);
+
+		if (check_update_reserved_vmid(vmid, newvmid)) {
+			atomic64_set(&kvm_vmid->id, newvmid);
+			return newvmid;
+		}
+
+		if (!__test_and_set_bit(vmid2idx(vmid), vmid_map)) {
+			atomic64_set(&kvm_vmid->id, newvmid);
+			return newvmid;
+		}
+	}
+
+	vmid = find_next_zero_bit(vmid_map, NUM_USER_VMIDS, cur_idx);
+	if (vmid != NUM_USER_VMIDS)
+		goto set_vmid;
+
+	/* We're out of VMIDs, so increment the global generation count */
+	generation = atomic64_add_return_relaxed(VMID_FIRST_VERSION,
+						 &vmid_generation);
+	flush_context();
+
+	/* We have more VMIDs than CPUs, so this will always succeed */
+	vmid = find_next_zero_bit(vmid_map, NUM_USER_VMIDS, 1);
+
+set_vmid:
+	__set_bit(vmid, vmid_map);
+	cur_idx = vmid;
+	vmid = idx2vmid(vmid) | generation;
+	atomic64_set(&kvm_vmid->id, vmid);
+	return vmid;
+}
+
+/* Called from vCPU sched out with preemption disabled */
+void kvm_arm_vmid_clear_active(void)
+{
+	atomic64_set(this_cpu_ptr(&active_vmids), VMID_ACTIVE_INVALID);
+}
+
+void kvm_arm_vmid_update(struct kvm_vmid *kvm_vmid)
+{
+	unsigned long flags;
+	u64 vmid, old_active_vmid;
+
+	vmid = atomic64_read(&kvm_vmid->id);
+
+	/*
+	 * Please refer comments in check_and_switch_context() in
+	 * arch/arm64/mm/context.c.
+	 *
+	 * Unlike ASID allocator, we set the active_vmids to
+	 * VMID_ACTIVE_INVALID on vCPU schedule out to avoid
+	 * reserving the VMID space needlessly on rollover.
+	 * Hence explicitly check here for a "!= 0" to
+	 * handle the sync with a concurrent rollover.
+	 */
+	old_active_vmid = atomic64_read(this_cpu_ptr(&active_vmids));
+	if (old_active_vmid != 0 && vmid_gen_match(vmid) &&
+	    0 != atomic64_cmpxchg_relaxed(this_cpu_ptr(&active_vmids),
+					  old_active_vmid, vmid))
+		return;
+
+	raw_spin_lock_irqsave(&cpu_vmid_lock, flags);
+
+	/* Check that our VMID belongs to the current generation. */
+	vmid = atomic64_read(&kvm_vmid->id);
+	if (!vmid_gen_match(vmid))
+		vmid = new_vmid(kvm_vmid);
+
+	atomic64_set(this_cpu_ptr(&active_vmids), vmid);
+	raw_spin_unlock_irqrestore(&cpu_vmid_lock, flags);
+}
+
+/*
+ * Initialize the VMID allocator
+ */
+int kvm_arm_vmid_alloc_init(void)
+{
+	kvm_arm_vmid_bits = kvm_get_vmid_bits();
+
+	/*
+	 * Expect allocation after rollover to fail if we don't have
+	 * at least one more VMID than CPUs. VMID #0 is always reserved.
+	 */
+	WARN_ON(NUM_USER_VMIDS - 1 <= num_possible_cpus());
+	atomic64_set(&vmid_generation, VMID_FIRST_VERSION);
+	vmid_map = kcalloc(BITS_TO_LONGS(NUM_USER_VMIDS),
+			   sizeof(*vmid_map), GFP_KERNEL);
+	if (!vmid_map)
+		return -ENOMEM;
+
+	return 0;
+}
+
+void kvm_arm_vmid_alloc_free(void)
+{
+	kfree(vmid_map);
+}
diff --git a/arch/arm64/lib/clear_page.S b/arch/arm64/lib/clear_page.S
index b84b179edba3..ebde40e7fa2b 100644
--- a/arch/arm64/lib/clear_page.S
+++ b/arch/arm64/lib/clear_page.S
@@ -14,8 +14,9 @@
  * Parameters:
  *	x0 - dest
  */
-SYM_FUNC_START_PI(clear_page)
+SYM_FUNC_START(__pi_clear_page)
 	mrs	x1, dczid_el0
+	tbnz	x1, #4, 2f	/* Branch if DC ZVA is prohibited */
 	and	w1, w1, #0xf
 	mov	x2, #4
 	lsl	x1, x2, x1
@@ -25,5 +26,15 @@ SYM_FUNC_START_PI(clear_page)
 	tst	x0, #(PAGE_SIZE - 1)
 	b.ne	1b
 	ret
-SYM_FUNC_END_PI(clear_page)
+
+2:	stnp	xzr, xzr, [x0]
+	stnp	xzr, xzr, [x0, #16]
+	stnp	xzr, xzr, [x0, #32]
+	stnp	xzr, xzr, [x0, #48]
+	add	x0, x0, #64
+	tst	x0, #(PAGE_SIZE - 1)
+	b.ne	2b
+	ret
+SYM_FUNC_END(__pi_clear_page)
+SYM_FUNC_ALIAS(clear_page, __pi_clear_page)
 EXPORT_SYMBOL(clear_page)
diff --git a/arch/arm64/lib/copy_page.S b/arch/arm64/lib/copy_page.S
index 29144f4cd449..c336d2ffdec5 100644
--- a/arch/arm64/lib/copy_page.S
+++ b/arch/arm64/lib/copy_page.S
@@ -17,7 +17,7 @@
  *	x0 - dest
  *	x1 - src
  */
-SYM_FUNC_START_PI(copy_page)
+SYM_FUNC_START(__pi_copy_page)
 alternative_if ARM64_HAS_NO_HW_PREFETCH
 	// Prefetch three cache lines ahead.
 	prfm	pldl1strm, [x1, #128]
@@ -75,5 +75,6 @@ alternative_else_nop_endif
 	stnp	x16, x17, [x0, #112 - 256]
 
 	ret
-SYM_FUNC_END_PI(copy_page)
+SYM_FUNC_END(__pi_copy_page)
+SYM_FUNC_ALIAS(copy_page, __pi_copy_page)
 EXPORT_SYMBOL(copy_page)
diff --git a/arch/arm64/lib/crc32.S b/arch/arm64/lib/crc32.S
index 0f9e10ecda23..8340dccff46f 100644
--- a/arch/arm64/lib/crc32.S
+++ b/arch/arm64/lib/crc32.S
@@ -11,7 +11,44 @@
 
 	.arch		armv8-a+crc
 
-	.macro		__crc32, c
+	.macro		byteorder, reg, be
+	.if		\be
+CPU_LE( rev		\reg, \reg	)
+	.else
+CPU_BE( rev		\reg, \reg	)
+	.endif
+	.endm
+
+	.macro		byteorder16, reg, be
+	.if		\be
+CPU_LE( rev16		\reg, \reg	)
+	.else
+CPU_BE( rev16		\reg, \reg	)
+	.endif
+	.endm
+
+	.macro		bitorder, reg, be
+	.if		\be
+	rbit		\reg, \reg
+	.endif
+	.endm
+
+	.macro		bitorder16, reg, be
+	.if		\be
+	rbit		\reg, \reg
+	lsr		\reg, \reg, #16
+	.endif
+	.endm
+
+	.macro		bitorder8, reg, be
+	.if		\be
+	rbit		\reg, \reg
+	lsr		\reg, \reg, #24
+	.endif
+	.endm
+
+	.macro		__crc32, c, be=0
+	bitorder	w0, \be
 	cmp		x2, #16
 	b.lt		8f			// less than 16 bytes
 
@@ -24,10 +61,14 @@
 	add		x8, x8, x1
 	add		x1, x1, x7
 	ldp		x5, x6, [x8]
-CPU_BE(	rev		x3, x3		)
-CPU_BE(	rev		x4, x4		)
-CPU_BE(	rev		x5, x5		)
-CPU_BE(	rev		x6, x6		)
+	byteorder	x3, \be
+	byteorder	x4, \be
+	byteorder	x5, \be
+	byteorder	x6, \be
+	bitorder	x3, \be
+	bitorder	x4, \be
+	bitorder	x5, \be
+	bitorder	x6, \be
 
 	tst		x7, #8
 	crc32\c\()x	w8, w0, x3
@@ -55,33 +96,43 @@ CPU_BE(	rev		x6, x6		)
 32:	ldp		x3, x4, [x1], #32
 	sub		x2, x2, #32
 	ldp		x5, x6, [x1, #-16]
-CPU_BE(	rev		x3, x3		)
-CPU_BE(	rev		x4, x4		)
-CPU_BE(	rev		x5, x5		)
-CPU_BE(	rev		x6, x6		)
+	byteorder	x3, \be
+	byteorder	x4, \be
+	byteorder	x5, \be
+	byteorder	x6, \be
+	bitorder	x3, \be
+	bitorder	x4, \be
+	bitorder	x5, \be
+	bitorder	x6, \be
 	crc32\c\()x	w0, w0, x3
 	crc32\c\()x	w0, w0, x4
 	crc32\c\()x	w0, w0, x5
 	crc32\c\()x	w0, w0, x6
 	cbnz		x2, 32b
-0:	ret
+0:	bitorder	w0, \be
+	ret
 
 8:	tbz		x2, #3, 4f
 	ldr		x3, [x1], #8
-CPU_BE(	rev		x3, x3		)
+	byteorder	x3, \be
+	bitorder	x3, \be
 	crc32\c\()x	w0, w0, x3
 4:	tbz		x2, #2, 2f
 	ldr		w3, [x1], #4
-CPU_BE(	rev		w3, w3		)
+	byteorder	w3, \be
+	bitorder	w3, \be
 	crc32\c\()w	w0, w0, w3
 2:	tbz		x2, #1, 1f
 	ldrh		w3, [x1], #2
-CPU_BE(	rev16		w3, w3		)
+	byteorder16	w3, \be
+	bitorder16	w3, \be
 	crc32\c\()h	w0, w0, w3
 1:	tbz		x2, #0, 0f
 	ldrb		w3, [x1]
+	bitorder8	w3, \be
 	crc32\c\()b	w0, w0, w3
-0:	ret
+0:	bitorder	w0, \be
+	ret
 	.endm
 
 	.align		5
@@ -99,3 +150,11 @@ alternative_if_not ARM64_HAS_CRC32
 alternative_else_nop_endif
 	__crc32		c
 SYM_FUNC_END(__crc32c_le)
+
+	.align		5
+SYM_FUNC_START(crc32_be)
+alternative_if_not ARM64_HAS_CRC32
+	b		crc32_be_base
+alternative_else_nop_endif
+	__crc32		be=1
+SYM_FUNC_END(crc32_be)
diff --git a/arch/arm64/lib/delay.c b/arch/arm64/lib/delay.c
index 1688af0a4c97..5b7890139bc2 100644
--- a/arch/arm64/lib/delay.c
+++ b/arch/arm64/lib/delay.c
@@ -27,7 +27,17 @@ void __delay(unsigned long cycles)
 {
 	cycles_t start = get_cycles();
 
-	if (arch_timer_evtstrm_available()) {
+	if (cpus_have_const_cap(ARM64_HAS_WFXT)) {
+		u64 end = start + cycles;
+
+		/*
+		 * Start with WFIT. If an interrupt makes us resume
+		 * early, use a WFET loop to complete the delay.
+		 */
+		wfit(end);
+		while ((get_cycles() - start) < cycles)
+			wfet(end);
+	} else 	if (arch_timer_evtstrm_available()) {
 		const cycles_t timer_evt_period =
 			USECS_TO_CYCLES(ARCH_TIMER_EVT_STREAM_PERIOD_US);
 
diff --git a/arch/arm64/lib/insn.c b/arch/arm64/lib/insn.c
index fccfe363e567..49e972beeac7 100644
--- a/arch/arm64/lib/insn.c
+++ b/arch/arm64/lib/insn.c
@@ -299,36 +299,31 @@ static u32 aarch64_insn_encode_register(enum aarch64_insn_register_type type,
 	return insn;
 }
 
+static const u32 aarch64_insn_ldst_size[] = {
+	[AARCH64_INSN_SIZE_8] = 0,
+	[AARCH64_INSN_SIZE_16] = 1,
+	[AARCH64_INSN_SIZE_32] = 2,
+	[AARCH64_INSN_SIZE_64] = 3,
+};
+
 static u32 aarch64_insn_encode_ldst_size(enum aarch64_insn_size_type type,
 					 u32 insn)
 {
 	u32 size;
 
-	switch (type) {
-	case AARCH64_INSN_SIZE_8:
-		size = 0;
-		break;
-	case AARCH64_INSN_SIZE_16:
-		size = 1;
-		break;
-	case AARCH64_INSN_SIZE_32:
-		size = 2;
-		break;
-	case AARCH64_INSN_SIZE_64:
-		size = 3;
-		break;
-	default:
+	if (type < AARCH64_INSN_SIZE_8 || type > AARCH64_INSN_SIZE_64) {
 		pr_err("%s: unknown size encoding %d\n", __func__, type);
 		return AARCH64_BREAK_FAULT;
 	}
 
+	size = aarch64_insn_ldst_size[type];
 	insn &= ~GENMASK(31, 30);
 	insn |= size << 30;
 
 	return insn;
 }
 
-static inline long branch_imm_common(unsigned long pc, unsigned long addr,
+static inline long label_imm_common(unsigned long pc, unsigned long addr,
 				     long range)
 {
 	long offset;
@@ -359,7 +354,7 @@ u32 __kprobes aarch64_insn_gen_branch_imm(unsigned long pc, unsigned long addr,
 	 * ARM64 virtual address arrangement guarantees all kernel and module
 	 * texts are within +/-128M.
 	 */
-	offset = branch_imm_common(pc, addr, SZ_128M);
+	offset = label_imm_common(pc, addr, SZ_128M);
 	if (offset >= SZ_128M)
 		return AARCH64_BREAK_FAULT;
 
@@ -387,7 +382,7 @@ u32 aarch64_insn_gen_comp_branch_imm(unsigned long pc, unsigned long addr,
 	u32 insn;
 	long offset;
 
-	offset = branch_imm_common(pc, addr, SZ_1M);
+	offset = label_imm_common(pc, addr, SZ_1M);
 	if (offset >= SZ_1M)
 		return AARCH64_BREAK_FAULT;
 
@@ -426,7 +421,7 @@ u32 aarch64_insn_gen_cond_branch_imm(unsigned long pc, unsigned long addr,
 	u32 insn;
 	long offset;
 
-	offset = branch_imm_common(pc, addr, SZ_1M);
+	offset = label_imm_common(pc, addr, SZ_1M);
 
 	insn = aarch64_insn_get_bcond_value();
 
@@ -504,6 +499,72 @@ u32 aarch64_insn_gen_load_store_reg(enum aarch64_insn_register reg,
 					    offset);
 }
 
+u32 aarch64_insn_gen_load_store_imm(enum aarch64_insn_register reg,
+				    enum aarch64_insn_register base,
+				    unsigned int imm,
+				    enum aarch64_insn_size_type size,
+				    enum aarch64_insn_ldst_type type)
+{
+	u32 insn;
+	u32 shift;
+
+	if (size < AARCH64_INSN_SIZE_8 || size > AARCH64_INSN_SIZE_64) {
+		pr_err("%s: unknown size encoding %d\n", __func__, type);
+		return AARCH64_BREAK_FAULT;
+	}
+
+	shift = aarch64_insn_ldst_size[size];
+	if (imm & ~(BIT(12 + shift) - BIT(shift))) {
+		pr_err("%s: invalid imm: %d\n", __func__, imm);
+		return AARCH64_BREAK_FAULT;
+	}
+
+	imm >>= shift;
+
+	switch (type) {
+	case AARCH64_INSN_LDST_LOAD_IMM_OFFSET:
+		insn = aarch64_insn_get_ldr_imm_value();
+		break;
+	case AARCH64_INSN_LDST_STORE_IMM_OFFSET:
+		insn = aarch64_insn_get_str_imm_value();
+		break;
+	default:
+		pr_err("%s: unknown load/store encoding %d\n", __func__, type);
+		return AARCH64_BREAK_FAULT;
+	}
+
+	insn = aarch64_insn_encode_ldst_size(size, insn);
+
+	insn = aarch64_insn_encode_register(AARCH64_INSN_REGTYPE_RT, insn, reg);
+
+	insn = aarch64_insn_encode_register(AARCH64_INSN_REGTYPE_RN, insn,
+					    base);
+
+	return aarch64_insn_encode_immediate(AARCH64_INSN_IMM_12, insn, imm);
+}
+
+u32 aarch64_insn_gen_load_literal(unsigned long pc, unsigned long addr,
+				  enum aarch64_insn_register reg,
+				  bool is64bit)
+{
+	u32 insn;
+	long offset;
+
+	offset = label_imm_common(pc, addr, SZ_1M);
+	if (offset >= SZ_1M)
+		return AARCH64_BREAK_FAULT;
+
+	insn = aarch64_insn_get_ldr_lit_value();
+
+	if (is64bit)
+		insn |= BIT(30);
+
+	insn = aarch64_insn_encode_register(AARCH64_INSN_REGTYPE_RT, insn, reg);
+
+	return aarch64_insn_encode_immediate(AARCH64_INSN_IMM_19, insn,
+					     offset >> 2);
+}
+
 u32 aarch64_insn_gen_load_store_pair(enum aarch64_insn_register reg1,
 				     enum aarch64_insn_register reg2,
 				     enum aarch64_insn_register base,
@@ -578,10 +639,16 @@ u32 aarch64_insn_gen_load_store_ex(enum aarch64_insn_register reg,
 
 	switch (type) {
 	case AARCH64_INSN_LDST_LOAD_EX:
+	case AARCH64_INSN_LDST_LOAD_ACQ_EX:
 		insn = aarch64_insn_get_load_ex_value();
+		if (type == AARCH64_INSN_LDST_LOAD_ACQ_EX)
+			insn |= BIT(15);
 		break;
 	case AARCH64_INSN_LDST_STORE_EX:
+	case AARCH64_INSN_LDST_STORE_REL_EX:
 		insn = aarch64_insn_get_store_ex_value();
+		if (type == AARCH64_INSN_LDST_STORE_REL_EX)
+			insn |= BIT(15);
 		break;
 	default:
 		pr_err("%s: unknown load/store exclusive encoding %d\n", __func__, type);
@@ -603,12 +670,65 @@ u32 aarch64_insn_gen_load_store_ex(enum aarch64_insn_register reg,
 					    state);
 }
 
-u32 aarch64_insn_gen_ldadd(enum aarch64_insn_register result,
-			   enum aarch64_insn_register address,
-			   enum aarch64_insn_register value,
-			   enum aarch64_insn_size_type size)
+#ifdef CONFIG_ARM64_LSE_ATOMICS
+static u32 aarch64_insn_encode_ldst_order(enum aarch64_insn_mem_order_type type,
+					  u32 insn)
+{
+	u32 order;
+
+	switch (type) {
+	case AARCH64_INSN_MEM_ORDER_NONE:
+		order = 0;
+		break;
+	case AARCH64_INSN_MEM_ORDER_ACQ:
+		order = 2;
+		break;
+	case AARCH64_INSN_MEM_ORDER_REL:
+		order = 1;
+		break;
+	case AARCH64_INSN_MEM_ORDER_ACQREL:
+		order = 3;
+		break;
+	default:
+		pr_err("%s: unknown mem order %d\n", __func__, type);
+		return AARCH64_BREAK_FAULT;
+	}
+
+	insn &= ~GENMASK(23, 22);
+	insn |= order << 22;
+
+	return insn;
+}
+
+u32 aarch64_insn_gen_atomic_ld_op(enum aarch64_insn_register result,
+				  enum aarch64_insn_register address,
+				  enum aarch64_insn_register value,
+				  enum aarch64_insn_size_type size,
+				  enum aarch64_insn_mem_atomic_op op,
+				  enum aarch64_insn_mem_order_type order)
 {
-	u32 insn = aarch64_insn_get_ldadd_value();
+	u32 insn;
+
+	switch (op) {
+	case AARCH64_INSN_MEM_ATOMIC_ADD:
+		insn = aarch64_insn_get_ldadd_value();
+		break;
+	case AARCH64_INSN_MEM_ATOMIC_CLR:
+		insn = aarch64_insn_get_ldclr_value();
+		break;
+	case AARCH64_INSN_MEM_ATOMIC_EOR:
+		insn = aarch64_insn_get_ldeor_value();
+		break;
+	case AARCH64_INSN_MEM_ATOMIC_SET:
+		insn = aarch64_insn_get_ldset_value();
+		break;
+	case AARCH64_INSN_MEM_ATOMIC_SWP:
+		insn = aarch64_insn_get_swp_value();
+		break;
+	default:
+		pr_err("%s: unimplemented mem atomic op %d\n", __func__, op);
+		return AARCH64_BREAK_FAULT;
+	}
 
 	switch (size) {
 	case AARCH64_INSN_SIZE_32:
@@ -621,6 +741,8 @@ u32 aarch64_insn_gen_ldadd(enum aarch64_insn_register result,
 
 	insn = aarch64_insn_encode_ldst_size(size, insn);
 
+	insn = aarch64_insn_encode_ldst_order(order, insn);
+
 	insn = aarch64_insn_encode_register(AARCH64_INSN_REGTYPE_RT, insn,
 					    result);
 
@@ -631,17 +753,68 @@ u32 aarch64_insn_gen_ldadd(enum aarch64_insn_register result,
 					    value);
 }
 
-u32 aarch64_insn_gen_stadd(enum aarch64_insn_register address,
-			   enum aarch64_insn_register value,
-			   enum aarch64_insn_size_type size)
+static u32 aarch64_insn_encode_cas_order(enum aarch64_insn_mem_order_type type,
+					 u32 insn)
 {
-	/*
-	 * STADD is simply encoded as an alias for LDADD with XZR as
-	 * the destination register.
-	 */
-	return aarch64_insn_gen_ldadd(AARCH64_INSN_REG_ZR, address,
-				      value, size);
+	u32 order;
+
+	switch (type) {
+	case AARCH64_INSN_MEM_ORDER_NONE:
+		order = 0;
+		break;
+	case AARCH64_INSN_MEM_ORDER_ACQ:
+		order = BIT(22);
+		break;
+	case AARCH64_INSN_MEM_ORDER_REL:
+		order = BIT(15);
+		break;
+	case AARCH64_INSN_MEM_ORDER_ACQREL:
+		order = BIT(15) | BIT(22);
+		break;
+	default:
+		pr_err("%s: unknown mem order %d\n", __func__, type);
+		return AARCH64_BREAK_FAULT;
+	}
+
+	insn &= ~(BIT(15) | BIT(22));
+	insn |= order;
+
+	return insn;
+}
+
+u32 aarch64_insn_gen_cas(enum aarch64_insn_register result,
+			 enum aarch64_insn_register address,
+			 enum aarch64_insn_register value,
+			 enum aarch64_insn_size_type size,
+			 enum aarch64_insn_mem_order_type order)
+{
+	u32 insn;
+
+	switch (size) {
+	case AARCH64_INSN_SIZE_32:
+	case AARCH64_INSN_SIZE_64:
+		break;
+	default:
+		pr_err("%s: unimplemented size encoding %d\n", __func__, size);
+		return AARCH64_BREAK_FAULT;
+	}
+
+	insn = aarch64_insn_get_cas_value();
+
+	insn = aarch64_insn_encode_ldst_size(size, insn);
+
+	insn = aarch64_insn_encode_cas_order(order, insn);
+
+	insn = aarch64_insn_encode_register(AARCH64_INSN_REGTYPE_RT, insn,
+					    result);
+
+	insn = aarch64_insn_encode_register(AARCH64_INSN_REGTYPE_RN, insn,
+					    address);
+
+	return aarch64_insn_encode_register(AARCH64_INSN_REGTYPE_RS, insn,
+					    value);
 }
+#endif
 
 static u32 aarch64_insn_encode_prfm_imm(enum aarch64_insn_prfm_type type,
 					enum aarch64_insn_prfm_target target,
@@ -1379,7 +1552,7 @@ static u32 aarch64_encode_immediate(u64 imm,
 		 * Compute the rotation to get a continuous set of
 		 * ones, with the first bit set at position 0
 		 */
-		ror = fls(~imm);
+		ror = fls64(~imm);
 	}
 
 	/*
@@ -1456,3 +1629,48 @@ u32 aarch64_insn_gen_extr(enum aarch64_insn_variant variant,
 	insn = aarch64_insn_encode_register(AARCH64_INSN_REGTYPE_RN, insn, Rn);
 	return aarch64_insn_encode_register(AARCH64_INSN_REGTYPE_RM, insn, Rm);
 }
+
+u32 aarch64_insn_gen_dmb(enum aarch64_insn_mb_type type)
+{
+	u32 opt;
+	u32 insn;
+
+	switch (type) {
+	case AARCH64_INSN_MB_SY:
+		opt = 0xf;
+		break;
+	case AARCH64_INSN_MB_ST:
+		opt = 0xe;
+		break;
+	case AARCH64_INSN_MB_LD:
+		opt = 0xd;
+		break;
+	case AARCH64_INSN_MB_ISH:
+		opt = 0xb;
+		break;
+	case AARCH64_INSN_MB_ISHST:
+		opt = 0xa;
+		break;
+	case AARCH64_INSN_MB_ISHLD:
+		opt = 0x9;
+		break;
+	case AARCH64_INSN_MB_NSH:
+		opt = 0x7;
+		break;
+	case AARCH64_INSN_MB_NSHST:
+		opt = 0x6;
+		break;
+	case AARCH64_INSN_MB_NSHLD:
+		opt = 0x5;
+		break;
+	default:
+		pr_err("%s: unknown dmb type %d\n", __func__, type);
+		return AARCH64_BREAK_FAULT;
+	}
+
+	insn = aarch64_insn_get_dmb_value();
+	insn &= ~GENMASK(11, 8);
+	insn |= (opt << 8);
+
+	return insn;
+}
diff --git a/arch/arm64/lib/kasan_sw_tags.S b/arch/arm64/lib/kasan_sw_tags.S
index 5b04464c045e..20784ce75def 100644
--- a/arch/arm64/lib/kasan_sw_tags.S
+++ b/arch/arm64/lib/kasan_sw_tags.S
@@ -38,9 +38,7 @@
  * incremented by 256 prior to return).
  */
 SYM_CODE_START(__hwasan_tag_mismatch)
-#ifdef BTI_C
-	BTI_C
-#endif
+	bti	c
 	add	x29, sp, #232
 	stp	x2, x3, [sp, #8 * 2]
 	stp	x4, x5, [sp, #8 * 4]
diff --git a/arch/arm64/lib/memchr.S b/arch/arm64/lib/memchr.S
index 7c2276fdab54..37a9f2a4f7f4 100644
--- a/arch/arm64/lib/memchr.S
+++ b/arch/arm64/lib/memchr.S
@@ -38,7 +38,7 @@
 
 	.p2align 4
 	nop
-SYM_FUNC_START_WEAK_PI(memchr)
+SYM_FUNC_START(__pi_memchr)
 	and	chrin, chrin, #0xff
 	lsr	wordcnt, cntin, #3
 	cbz	wordcnt, L(byte_loop)
@@ -71,5 +71,6 @@ CPU_LE(	rev	tmp, tmp)
 L(not_found):
 	mov	result, #0
 	ret
-SYM_FUNC_END_PI(memchr)
+SYM_FUNC_END(__pi_memchr)
+SYM_FUNC_ALIAS_WEAK(memchr, __pi_memchr)
 EXPORT_SYMBOL_NOKASAN(memchr)
diff --git a/arch/arm64/lib/memcmp.S b/arch/arm64/lib/memcmp.S
index 7d956384222f..a5ccf2c55f91 100644
--- a/arch/arm64/lib/memcmp.S
+++ b/arch/arm64/lib/memcmp.S
@@ -32,7 +32,7 @@
 #define tmp1		x7
 #define tmp2		x8
 
-SYM_FUNC_START_WEAK_PI(memcmp)
+SYM_FUNC_START(__pi_memcmp)
 	subs	limit, limit, 8
 	b.lo	L(less8)
 
@@ -134,6 +134,6 @@ L(byte_loop):
 	b.eq	L(byte_loop)
 	sub	result, data1w, data2w
 	ret
-
-SYM_FUNC_END_PI(memcmp)
+SYM_FUNC_END(__pi_memcmp)
+SYM_FUNC_ALIAS_WEAK(memcmp, __pi_memcmp)
 EXPORT_SYMBOL_NOKASAN(memcmp)
diff --git a/arch/arm64/lib/memcpy.S b/arch/arm64/lib/memcpy.S
index b82fd64ee1e1..4ab48d49c451 100644
--- a/arch/arm64/lib/memcpy.S
+++ b/arch/arm64/lib/memcpy.S
@@ -57,10 +57,7 @@
    The loop tail is handled by always copying 64 bytes from the end.
 */
 
-SYM_FUNC_START_ALIAS(__memmove)
-SYM_FUNC_START_WEAK_ALIAS_PI(memmove)
-SYM_FUNC_START_ALIAS(__memcpy)
-SYM_FUNC_START_WEAK_PI(memcpy)
+SYM_FUNC_START(__pi_memcpy)
 	add	srcend, src, count
 	add	dstend, dstin, count
 	cmp	count, 128
@@ -241,12 +238,16 @@ L(copy64_from_start):
 	stp	B_l, B_h, [dstin, 16]
 	stp	C_l, C_h, [dstin]
 	ret
+SYM_FUNC_END(__pi_memcpy)
 
-SYM_FUNC_END_PI(memcpy)
-EXPORT_SYMBOL(memcpy)
-SYM_FUNC_END_ALIAS(__memcpy)
+SYM_FUNC_ALIAS(__memcpy, __pi_memcpy)
 EXPORT_SYMBOL(__memcpy)
-SYM_FUNC_END_ALIAS_PI(memmove)
-EXPORT_SYMBOL(memmove)
-SYM_FUNC_END_ALIAS(__memmove)
+SYM_FUNC_ALIAS_WEAK(memcpy, __memcpy)
+EXPORT_SYMBOL(memcpy)
+
+SYM_FUNC_ALIAS(__pi_memmove, __pi_memcpy)
+
+SYM_FUNC_ALIAS(__memmove, __pi_memmove)
 EXPORT_SYMBOL(__memmove)
+SYM_FUNC_ALIAS_WEAK(memmove, __memmove)
+EXPORT_SYMBOL(memmove)
diff --git a/arch/arm64/lib/memset.S b/arch/arm64/lib/memset.S
index a9c1c9a01ea9..a5aebe82ad73 100644
--- a/arch/arm64/lib/memset.S
+++ b/arch/arm64/lib/memset.S
@@ -42,8 +42,7 @@ dst		.req	x8
 tmp3w		.req	w9
 tmp3		.req	x9
 
-SYM_FUNC_START_ALIAS(__memset)
-SYM_FUNC_START_WEAK_PI(memset)
+SYM_FUNC_START(__pi_memset)
 	mov	dst, dstin	/* Preserve return value.  */
 	and	A_lw, val, #255
 	orr	A_lw, A_lw, A_lw, lsl #8
@@ -202,7 +201,10 @@ SYM_FUNC_START_WEAK_PI(memset)
 	ands	count, count, zva_bits_x
 	b.ne	.Ltail_maybe_long
 	ret
-SYM_FUNC_END_PI(memset)
-EXPORT_SYMBOL(memset)
-SYM_FUNC_END_ALIAS(__memset)
+SYM_FUNC_END(__pi_memset)
+
+SYM_FUNC_ALIAS(__memset, __pi_memset)
 EXPORT_SYMBOL(__memset)
+
+SYM_FUNC_ALIAS_WEAK(memset, __pi_memset)
+EXPORT_SYMBOL(memset)
diff --git a/arch/arm64/lib/mte.S b/arch/arm64/lib/mte.S
index e83643b3995f..1b7c93ae7e63 100644
--- a/arch/arm64/lib/mte.S
+++ b/arch/arm64/lib/mte.S
@@ -18,7 +18,7 @@
  */
 	.macro	multitag_transfer_size, reg, tmp
 	mrs_s	\reg, SYS_GMID_EL1
-	ubfx	\reg, \reg, #SYS_GMID_EL1_BS_SHIFT, #SYS_GMID_EL1_BS_SIZE
+	ubfx	\reg, \reg, #GMID_EL1_BS_SHIFT, #GMID_EL1_BS_SIZE
 	mov	\tmp, #4
 	lsl	\reg, \tmp, \reg
 	.endm
@@ -43,17 +43,23 @@ SYM_FUNC_END(mte_clear_page_tags)
  *	x0 - address to the beginning of the page
  */
 SYM_FUNC_START(mte_zero_clear_page_tags)
+	and	x0, x0, #(1 << MTE_TAG_SHIFT) - 1	// clear the tag
 	mrs	x1, dczid_el0
+	tbnz	x1, #4, 2f	// Branch if DC GZVA is prohibited
 	and	w1, w1, #0xf
 	mov	x2, #4
 	lsl	x1, x2, x1
-	and	x0, x0, #(1 << MTE_TAG_SHIFT) - 1	// clear the tag
 
 1:	dc	gzva, x0
 	add	x0, x0, x1
 	tst	x0, #(PAGE_SIZE - 1)
 	b.ne	1b
 	ret
+
+2:	stz2g	x0, [x0], #(MTE_GRANULE_SIZE * 2)
+	tst	x0, #(PAGE_SIZE - 1)
+	b.ne	2b
+	ret
 SYM_FUNC_END(mte_zero_clear_page_tags)
 
 /*
@@ -87,7 +93,7 @@ SYM_FUNC_START(mte_copy_tags_from_user)
 	mov	x3, x1
 	cbz	x2, 2f
 1:
-	user_ldst 2f, ldtrb, w4, x1, 0
+USER(2f, ldtrb	w4, [x1])
 	lsl	x4, x4, #MTE_TAG_SHIFT
 	stg	x4, [x0], #MTE_GRANULE_SIZE
 	add	x1, x1, #1
@@ -114,7 +120,7 @@ SYM_FUNC_START(mte_copy_tags_to_user)
 1:
 	ldg	x4, [x1]
 	ubfx	x4, x4, #MTE_TAG_SHIFT, #MTE_TAG_SIZE
-	user_ldst 2f, sttrb, w4, x0, 0
+USER(2f, sttrb	w4, [x0])
 	add	x0, x0, #1
 	add	x1, x1, #MTE_GRANULE_SIZE
 	subs	x2, x2, #1
@@ -128,7 +134,7 @@ SYM_FUNC_END(mte_copy_tags_to_user)
 /*
  * Save the tags in a page
  *   x0 - page address
- *   x1 - tag storage
+ *   x1 - tag storage, MTE_PAGE_TAG_STORAGE bytes
  */
 SYM_FUNC_START(mte_save_page_tags)
 	multitag_transfer_size x7, x5
@@ -152,7 +158,7 @@ SYM_FUNC_END(mte_save_page_tags)
 /*
  * Restore the tags in a page
  *   x0 - page address
- *   x1 - tag storage
+ *   x1 - tag storage, MTE_PAGE_TAG_STORAGE bytes
  */
 SYM_FUNC_START(mte_restore_page_tags)
 	multitag_transfer_size x7, x5
diff --git a/arch/arm64/lib/strchr.S b/arch/arm64/lib/strchr.S
index 1f47eae3b0d6..94ee67a6b212 100644
--- a/arch/arm64/lib/strchr.S
+++ b/arch/arm64/lib/strchr.S
@@ -18,7 +18,7 @@
  * Returns:
  *	x0 - address of first occurrence of 'c' or 0
  */
-SYM_FUNC_START_WEAK(strchr)
+SYM_FUNC_START(__pi_strchr)
 	and	w1, w1, #0xff
 1:	ldrb	w2, [x0], #1
 	cmp	w2, w1
@@ -28,5 +28,7 @@ SYM_FUNC_START_WEAK(strchr)
 	cmp	w2, w1
 	csel	x0, x0, xzr, eq
 	ret
-SYM_FUNC_END(strchr)
+SYM_FUNC_END(__pi_strchr)
+
+SYM_FUNC_ALIAS_WEAK(strchr, __pi_strchr)
 EXPORT_SYMBOL_NOKASAN(strchr)
diff --git a/arch/arm64/lib/strcmp.S b/arch/arm64/lib/strcmp.S
index 83bcad72ec97..9b89b4533607 100644
--- a/arch/arm64/lib/strcmp.S
+++ b/arch/arm64/lib/strcmp.S
@@ -1,9 +1,9 @@
 /* SPDX-License-Identifier: GPL-2.0-only */
 /*
- * Copyright (c) 2012-2021, Arm Limited.
+ * Copyright (c) 2012-2022, Arm Limited.
  *
  * Adapted from the original at:
- * https://github.com/ARM-software/optimized-routines/blob/afd6244a1f8d9229/string/aarch64/strcmp.S
+ * https://github.com/ARM-software/optimized-routines/blob/189dfefe37d54c5b/string/aarch64/strcmp.S
  */
 
 #include <linux/linkage.h>
@@ -11,166 +11,180 @@
 
 /* Assumptions:
  *
- * ARMv8-a, AArch64
+ * ARMv8-a, AArch64.
+ * MTE compatible.
  */
 
 #define L(label) .L ## label
 
 #define REP8_01 0x0101010101010101
 #define REP8_7f 0x7f7f7f7f7f7f7f7f
-#define REP8_80 0x8080808080808080
 
-/* Parameters and result.  */
 #define src1		x0
 #define src2		x1
 #define result		x0
 
-/* Internal variables.  */
 #define data1		x2
 #define data1w		w2
 #define data2		x3
 #define data2w		w3
 #define has_nul		x4
 #define diff		x5
+#define off1		x5
 #define syndrome	x6
-#define tmp1		x7
-#define tmp2		x8
-#define tmp3		x9
-#define zeroones	x10
-#define pos		x11
-
-	/* Start of performance-critical section  -- one 64B cache line.  */
-	.align 6
-SYM_FUNC_START_WEAK_PI(strcmp)
-	eor	tmp1, src1, src2
-	mov	zeroones, #REP8_01
-	tst	tmp1, #7
+#define tmp		x6
+#define data3		x7
+#define zeroones	x8
+#define shift		x9
+#define off2		x10
+
+/* On big-endian early bytes are at MSB and on little-endian LSB.
+   LS_FW means shifting towards early bytes.  */
+#ifdef __AARCH64EB__
+# define LS_FW lsl
+#else
+# define LS_FW lsr
+#endif
+
+/* NUL detection works on the principle that (X - 1) & (~X) & 0x80
+   (=> (X - 1) & ~(X | 0x7f)) is non-zero iff a byte is zero, and
+   can be done in parallel across the entire word.
+   Since carry propagation makes 0x1 bytes before a NUL byte appear
+   NUL too in big-endian, byte-reverse the data before the NUL check.  */
+
+
+SYM_FUNC_START(__pi_strcmp)
+	sub	off2, src2, src1
+	mov	zeroones, REP8_01
+	and	tmp, src1, 7
+	tst	off2, 7
 	b.ne	L(misaligned8)
-	ands	tmp1, src1, #7
-	b.ne	L(mutual_align)
-	/* NUL detection works on the principle that (X - 1) & (~X) & 0x80
-	   (=> (X - 1) & ~(X | 0x7f)) is non-zero iff a byte is zero, and
-	   can be done in parallel across the entire word.  */
+	cbnz	tmp, L(mutual_align)
+
+	.p2align 4
+
 L(loop_aligned):
-	ldr	data1, [src1], #8
-	ldr	data2, [src2], #8
+	ldr	data2, [src1, off2]
+	ldr	data1, [src1], 8
 L(start_realigned):
-	sub	tmp1, data1, zeroones
-	orr	tmp2, data1, #REP8_7f
-	eor	diff, data1, data2	/* Non-zero if differences found.  */
-	bic	has_nul, tmp1, tmp2	/* Non-zero if NUL terminator.  */
+#ifdef __AARCH64EB__
+	rev	tmp, data1
+	sub	has_nul, tmp, zeroones
+	orr	tmp, tmp, REP8_7f
+#else
+	sub	has_nul, data1, zeroones
+	orr	tmp, data1, REP8_7f
+#endif
+	bics	has_nul, has_nul, tmp	/* Non-zero if NUL terminator.  */
+	ccmp	data1, data2, 0, eq
+	b.eq	L(loop_aligned)
+#ifdef __AARCH64EB__
+	rev	has_nul, has_nul
+#endif
+	eor	diff, data1, data2
 	orr	syndrome, diff, has_nul
-	cbz	syndrome, L(loop_aligned)
-	/* End of performance-critical section  -- one 64B cache line.  */
-
 L(end):
-#ifndef	__AARCH64EB__
+#ifndef __AARCH64EB__
 	rev	syndrome, syndrome
 	rev	data1, data1
-	/* The MS-non-zero bit of the syndrome marks either the first bit
-	   that is different, or the top bit of the first zero byte.
-	   Shifting left now will bring the critical information into the
-	   top bits.  */
-	clz	pos, syndrome
 	rev	data2, data2
-	lsl	data1, data1, pos
-	lsl	data2, data2, pos
-	/* But we need to zero-extend (char is unsigned) the value and then
-	   perform a signed 32-bit subtraction.  */
-	lsr	data1, data1, #56
-	sub	result, data1, data2, lsr #56
-	ret
-#else
-	/* For big-endian we cannot use the trick with the syndrome value
-	   as carry-propagation can corrupt the upper bits if the trailing
-	   bytes in the string contain 0x01.  */
-	/* However, if there is no NUL byte in the dword, we can generate
-	   the result directly.  We can't just subtract the bytes as the
-	   MSB might be significant.  */
-	cbnz	has_nul, 1f
-	cmp	data1, data2
-	cset	result, ne
-	cneg	result, result, lo
-	ret
-1:
-	/* Re-compute the NUL-byte detection, using a byte-reversed value.  */
-	rev	tmp3, data1
-	sub	tmp1, tmp3, zeroones
-	orr	tmp2, tmp3, #REP8_7f
-	bic	has_nul, tmp1, tmp2
-	rev	has_nul, has_nul
-	orr	syndrome, diff, has_nul
-	clz	pos, syndrome
-	/* The MS-non-zero bit of the syndrome marks either the first bit
-	   that is different, or the top bit of the first zero byte.
+#endif
+	clz	shift, syndrome
+	/* The most-significant-non-zero bit of the syndrome marks either the
+	   first bit that is different, or the top bit of the first zero byte.
 	   Shifting left now will bring the critical information into the
 	   top bits.  */
-	lsl	data1, data1, pos
-	lsl	data2, data2, pos
+	lsl	data1, data1, shift
+	lsl	data2, data2, shift
 	/* But we need to zero-extend (char is unsigned) the value and then
 	   perform a signed 32-bit subtraction.  */
-	lsr	data1, data1, #56
-	sub	result, data1, data2, lsr #56
+	lsr	data1, data1, 56
+	sub	result, data1, data2, lsr 56
 	ret
-#endif
+
+	.p2align 4
 
 L(mutual_align):
 	/* Sources are mutually aligned, but are not currently at an
 	   alignment boundary.  Round down the addresses and then mask off
-	   the bytes that preceed the start point.  */
-	bic	src1, src1, #7
-	bic	src2, src2, #7
-	lsl	tmp1, tmp1, #3		/* Bytes beyond alignment -> bits.  */
-	ldr	data1, [src1], #8
-	neg	tmp1, tmp1		/* Bits to alignment -64.  */
-	ldr	data2, [src2], #8
-	mov	tmp2, #~0
-#ifdef __AARCH64EB__
-	/* Big-endian.  Early bytes are at MSB.  */
-	lsl	tmp2, tmp2, tmp1	/* Shift (tmp1 & 63).  */
-#else
-	/* Little-endian.  Early bytes are at LSB.  */
-	lsr	tmp2, tmp2, tmp1	/* Shift (tmp1 & 63).  */
-#endif
-	orr	data1, data1, tmp2
-	orr	data2, data2, tmp2
+	   the bytes that precede the start point.  */
+	bic	src1, src1, 7
+	ldr	data2, [src1, off2]
+	ldr	data1, [src1], 8
+	neg	shift, src2, lsl 3	/* Bits to alignment -64.  */
+	mov	tmp, -1
+	LS_FW	tmp, tmp, shift
+	orr	data1, data1, tmp
+	orr	data2, data2, tmp
 	b	L(start_realigned)
 
 L(misaligned8):
 	/* Align SRC1 to 8 bytes and then compare 8 bytes at a time, always
-	   checking to make sure that we don't access beyond page boundary in
-	   SRC2.  */
-	tst	src1, #7
-	b.eq	L(loop_misaligned)
+	   checking to make sure that we don't access beyond the end of SRC2.  */
+	cbz	tmp, L(src1_aligned)
 L(do_misaligned):
-	ldrb	data1w, [src1], #1
-	ldrb	data2w, [src2], #1
-	cmp	data1w, #1
-	ccmp	data1w, data2w, #0, cs	/* NZCV = 0b0000.  */
+	ldrb	data1w, [src1], 1
+	ldrb	data2w, [src2], 1
+	cmp	data1w, 0
+	ccmp	data1w, data2w, 0, ne	/* NZCV = 0b0000.  */
 	b.ne	L(done)
-	tst	src1, #7
+	tst	src1, 7
 	b.ne	L(do_misaligned)
 
-L(loop_misaligned):
-	/* Test if we are within the last dword of the end of a 4K page.  If
-	   yes then jump back to the misaligned loop to copy a byte at a time.  */
-	and	tmp1, src2, #0xff8
-	eor	tmp1, tmp1, #0xff8
-	cbz	tmp1, L(do_misaligned)
-	ldr	data1, [src1], #8
-	ldr	data2, [src2], #8
-
-	sub	tmp1, data1, zeroones
-	orr	tmp2, data1, #REP8_7f
-	eor	diff, data1, data2	/* Non-zero if differences found.  */
-	bic	has_nul, tmp1, tmp2	/* Non-zero if NUL terminator.  */
+L(src1_aligned):
+	neg	shift, src2, lsl 3
+	bic	src2, src2, 7
+	ldr	data3, [src2], 8
+#ifdef __AARCH64EB__
+	rev	data3, data3
+#endif
+	lsr	tmp, zeroones, shift
+	orr	data3, data3, tmp
+	sub	has_nul, data3, zeroones
+	orr	tmp, data3, REP8_7f
+	bics	has_nul, has_nul, tmp
+	b.ne	L(tail)
+
+	sub	off1, src2, src1
+
+	.p2align 4
+
+L(loop_unaligned):
+	ldr	data3, [src1, off1]
+	ldr	data2, [src1, off2]
+#ifdef __AARCH64EB__
+	rev	data3, data3
+#endif
+	sub	has_nul, data3, zeroones
+	orr	tmp, data3, REP8_7f
+	ldr	data1, [src1], 8
+	bics	has_nul, has_nul, tmp
+	ccmp	data1, data2, 0, eq
+	b.eq	L(loop_unaligned)
+
+	lsl	tmp, has_nul, shift
+#ifdef __AARCH64EB__
+	rev	tmp, tmp
+#endif
+	eor	diff, data1, data2
+	orr	syndrome, diff, tmp
+	cbnz	syndrome, L(end)
+L(tail):
+	ldr	data1, [src1]
+	neg	shift, shift
+	lsr	data2, data3, shift
+	lsr	has_nul, has_nul, shift
+#ifdef __AARCH64EB__
+	rev     data2, data2
+	rev	has_nul, has_nul
+#endif
+	eor	diff, data1, data2
 	orr	syndrome, diff, has_nul
-	cbz	syndrome, L(loop_misaligned)
 	b	L(end)
 
 L(done):
 	sub	result, data1, data2
 	ret
-
-SYM_FUNC_END_PI(strcmp)
-EXPORT_SYMBOL_NOHWKASAN(strcmp)
+SYM_FUNC_END(__pi_strcmp)
+SYM_FUNC_ALIAS_WEAK(strcmp, __pi_strcmp)
+EXPORT_SYMBOL_NOKASAN(strcmp)
diff --git a/arch/arm64/lib/strlen.S b/arch/arm64/lib/strlen.S
index 1648790e91b3..4919fe81ae54 100644
--- a/arch/arm64/lib/strlen.S
+++ b/arch/arm64/lib/strlen.S
@@ -79,7 +79,7 @@
 	   whether the first fetch, which may be misaligned, crosses a page
 	   boundary.  */
 
-SYM_FUNC_START_WEAK_PI(strlen)
+SYM_FUNC_START(__pi_strlen)
 	and	tmp1, srcin, MIN_PAGE_SIZE - 1
 	mov	zeroones, REP8_01
 	cmp	tmp1, MIN_PAGE_SIZE - 16
@@ -208,6 +208,6 @@ L(page_cross):
 	csel	data1, data1, tmp4, eq
 	csel	data2, data2, tmp2, eq
 	b	L(page_cross_entry)
-
-SYM_FUNC_END_PI(strlen)
+SYM_FUNC_END(__pi_strlen)
+SYM_FUNC_ALIAS_WEAK(strlen, __pi_strlen)
 EXPORT_SYMBOL_NOKASAN(strlen)
diff --git a/arch/arm64/lib/strncmp.S b/arch/arm64/lib/strncmp.S
index e42bcfcd37e6..fe7bbc0b42a7 100644
--- a/arch/arm64/lib/strncmp.S
+++ b/arch/arm64/lib/strncmp.S
@@ -1,9 +1,9 @@
 /* SPDX-License-Identifier: GPL-2.0-only */
 /*
- * Copyright (c) 2013-2021, Arm Limited.
+ * Copyright (c) 2013-2022, Arm Limited.
  *
  * Adapted from the original at:
- * https://github.com/ARM-software/optimized-routines/blob/e823e3abf5f89ecb/string/aarch64/strncmp.S
+ * https://github.com/ARM-software/optimized-routines/blob/189dfefe37d54c5b/string/aarch64/strncmp.S
  */
 
 #include <linux/linkage.h>
@@ -11,14 +11,14 @@
 
 /* Assumptions:
  *
- * ARMv8-a, AArch64
+ * ARMv8-a, AArch64.
+ * MTE compatible.
  */
 
 #define L(label) .L ## label
 
 #define REP8_01 0x0101010101010101
 #define REP8_7f 0x7f7f7f7f7f7f7f7f
-#define REP8_80 0x8080808080808080
 
 /* Parameters and result.  */
 #define src1		x0
@@ -39,12 +39,26 @@
 #define tmp3		x10
 #define zeroones	x11
 #define pos		x12
-#define limit_wd	x13
-#define mask		x14
-#define endloop		x15
+#define mask		x13
+#define endloop		x14
 #define count		mask
+#define offset		pos
+#define neg_offset	x15
 
-SYM_FUNC_START_WEAK_PI(strncmp)
+/* Define endian dependent shift operations.
+   On big-endian early bytes are at MSB and on little-endian LSB.
+   LS_FW means shifting towards early bytes.
+   LS_BK means shifting towards later bytes.
+   */
+#ifdef __AARCH64EB__
+#define LS_FW lsl
+#define LS_BK lsr
+#else
+#define LS_FW lsr
+#define LS_BK lsl
+#endif
+
+SYM_FUNC_START(__pi_strncmp)
 	cbz	limit, L(ret0)
 	eor	tmp1, src1, src2
 	mov	zeroones, #REP8_01
@@ -52,9 +66,6 @@ SYM_FUNC_START_WEAK_PI(strncmp)
 	and	count, src1, #7
 	b.ne	L(misaligned8)
 	cbnz	count, L(mutual_align)
-	/* Calculate the number of full and partial words -1.  */
-	sub	limit_wd, limit, #1	/* limit != 0, so no underflow.  */
-	lsr	limit_wd, limit_wd, #3	/* Convert to Dwords.  */
 
 	/* NUL detection works on the principle that (X - 1) & (~X) & 0x80
 	   (=> (X - 1) & ~(X | 0x7f)) is non-zero iff a byte is zero, and
@@ -64,56 +75,52 @@ L(loop_aligned):
 	ldr	data1, [src1], #8
 	ldr	data2, [src2], #8
 L(start_realigned):
-	subs	limit_wd, limit_wd, #1
+	subs	limit, limit, #8
 	sub	tmp1, data1, zeroones
 	orr	tmp2, data1, #REP8_7f
 	eor	diff, data1, data2	/* Non-zero if differences found.  */
-	csinv	endloop, diff, xzr, pl	/* Last Dword or differences.  */
+	csinv	endloop, diff, xzr, hi	/* Last Dword or differences.  */
 	bics	has_nul, tmp1, tmp2	/* Non-zero if NUL terminator.  */
 	ccmp	endloop, #0, #0, eq
 	b.eq	L(loop_aligned)
 	/* End of main loop */
 
-	/* Not reached the limit, must have found the end or a diff.  */
-	tbz	limit_wd, #63, L(not_limit)
-
-	/* Limit % 8 == 0 => all bytes significant.  */
-	ands	limit, limit, #7
-	b.eq	L(not_limit)
-
-	lsl	limit, limit, #3	/* Bits -> bytes.  */
-	mov	mask, #~0
-#ifdef __AARCH64EB__
-	lsr	mask, mask, limit
-#else
-	lsl	mask, mask, limit
-#endif
-	bic	data1, data1, mask
-	bic	data2, data2, mask
-
-	/* Make sure that the NUL byte is marked in the syndrome.  */
-	orr	has_nul, has_nul, mask
-
-L(not_limit):
+L(full_check):
+#ifndef __AARCH64EB__
 	orr	syndrome, diff, has_nul
-
-#ifndef	__AARCH64EB__
+	add	limit, limit, 8	/* Rewind limit to before last subs. */
+L(syndrome_check):
+	/* Limit was reached. Check if the NUL byte or the difference
+	   is before the limit. */
 	rev	syndrome, syndrome
 	rev	data1, data1
-	/* The MS-non-zero bit of the syndrome marks either the first bit
-	   that is different, or the top bit of the first zero byte.
-	   Shifting left now will bring the critical information into the
-	   top bits.  */
 	clz	pos, syndrome
 	rev	data2, data2
 	lsl	data1, data1, pos
+	cmp	limit, pos, lsr #3
 	lsl	data2, data2, pos
 	/* But we need to zero-extend (char is unsigned) the value and then
 	   perform a signed 32-bit subtraction.  */
 	lsr	data1, data1, #56
 	sub	result, data1, data2, lsr #56
+	csel result, result, xzr, hi
 	ret
 #else
+	/* Not reached the limit, must have found the end or a diff.  */
+	tbz	limit, #63, L(not_limit)
+	add	tmp1, limit, 8
+	cbz	limit, L(not_limit)
+
+	lsl	limit, tmp1, #3	/* Bits -> bytes.  */
+	mov	mask, #~0
+	lsr	mask, mask, limit
+	bic	data1, data1, mask
+	bic	data2, data2, mask
+
+	/* Make sure that the NUL byte is marked in the syndrome.  */
+	orr	has_nul, has_nul, mask
+
+L(not_limit):
 	/* For big-endian we cannot use the trick with the syndrome value
 	   as carry-propagation can corrupt the upper bits if the trailing
 	   bytes in the string contain 0x01.  */
@@ -134,10 +141,11 @@ L(not_limit):
 	rev	has_nul, has_nul
 	orr	syndrome, diff, has_nul
 	clz	pos, syndrome
-	/* The MS-non-zero bit of the syndrome marks either the first bit
-	   that is different, or the top bit of the first zero byte.
+	/* The most-significant-non-zero bit of the syndrome marks either the
+	   first bit that is different, or the top bit of the first zero byte.
 	   Shifting left now will bring the critical information into the
 	   top bits.  */
+L(end_quick):
 	lsl	data1, data1, pos
 	lsl	data2, data2, pos
 	/* But we need to zero-extend (char is unsigned) the value and then
@@ -159,22 +167,12 @@ L(mutual_align):
 	neg	tmp3, count, lsl #3	/* 64 - bits(bytes beyond align). */
 	ldr	data2, [src2], #8
 	mov	tmp2, #~0
-	sub	limit_wd, limit, #1	/* limit != 0, so no underflow.  */
-#ifdef __AARCH64EB__
-	/* Big-endian.  Early bytes are at MSB.  */
-	lsl	tmp2, tmp2, tmp3	/* Shift (count & 63).  */
-#else
-	/* Little-endian.  Early bytes are at LSB.  */
-	lsr	tmp2, tmp2, tmp3	/* Shift (count & 63).  */
-#endif
-	and	tmp3, limit_wd, #7
-	lsr	limit_wd, limit_wd, #3
-	/* Adjust the limit. Only low 3 bits used, so overflow irrelevant.  */
-	add	limit, limit, count
-	add	tmp3, tmp3, count
+	LS_FW	tmp2, tmp2, tmp3	/* Shift (count & 63).  */
+	/* Adjust the limit and ensure it doesn't overflow.  */
+	adds	limit, limit, count
+	csinv	limit, limit, xzr, lo
 	orr	data1, data1, tmp2
 	orr	data2, data2, tmp2
-	add	limit_wd, limit_wd, tmp3, lsr #3
 	b	L(start_realigned)
 
 	.p2align 4
@@ -197,13 +195,11 @@ L(done):
 	/* Align the SRC1 to a dword by doing a bytewise compare and then do
 	   the dword loop.  */
 L(try_misaligned_words):
-	lsr	limit_wd, limit, #3
-	cbz	count, L(do_misaligned)
+	cbz	count, L(src1_aligned)
 
 	neg	count, count
 	and	count, count, #7
 	sub	limit, limit, count
-	lsr	limit_wd, limit, #3
 
 L(page_end_loop):
 	ldrb	data1w, [src1], #1
@@ -214,48 +210,101 @@ L(page_end_loop):
 	subs	count, count, #1
 	b.hi	L(page_end_loop)
 
-L(do_misaligned):
-	/* Prepare ourselves for the next page crossing.  Unlike the aligned
-	   loop, we fetch 1 less dword because we risk crossing bounds on
-	   SRC2.  */
-	mov	count, #8
-	subs	limit_wd, limit_wd, #1
-	b.lo	L(done_loop)
-L(loop_misaligned):
-	and	tmp2, src2, #0xff8
-	eor	tmp2, tmp2, #0xff8
-	cbz	tmp2, L(page_end_loop)
+	/* The following diagram explains the comparison of misaligned strings.
+	   The bytes are shown in natural order. For little-endian, it is
+	   reversed in the registers. The "x" bytes are before the string.
+	   The "|" separates data that is loaded at one time.
+	   src1     | a a a a a a a a | b b b c c c c c | . . .
+	   src2     | x x x x x a a a   a a a a a b b b | c c c c c . . .
+
+	   After shifting in each step, the data looks like this:
+	                STEP_A              STEP_B              STEP_C
+	   data1    a a a a a a a a     b b b c c c c c     b b b c c c c c
+	   data2    a a a a a a a a     b b b 0 0 0 0 0     0 0 0 c c c c c
 
+	   The bytes with "0" are eliminated from the syndrome via mask.
+
+	   Align SRC2 down to 16 bytes. This way we can read 16 bytes at a
+	   time from SRC2. The comparison happens in 3 steps. After each step
+	   the loop can exit, or read from SRC1 or SRC2. */
+L(src1_aligned):
+	/* Calculate offset from 8 byte alignment to string start in bits. No
+	   need to mask offset since shifts are ignoring upper bits. */
+	lsl	offset, src2, #3
+	bic	src2, src2, #0xf
+	mov	mask, -1
+	neg	neg_offset, offset
 	ldr	data1, [src1], #8
-	ldr	data2, [src2], #8
-	sub	tmp1, data1, zeroones
-	orr	tmp2, data1, #REP8_7f
-	eor	diff, data1, data2	/* Non-zero if differences found.  */
-	bics	has_nul, tmp1, tmp2	/* Non-zero if NUL terminator.  */
-	ccmp	diff, #0, #0, eq
-	b.ne	L(not_limit)
-	subs	limit_wd, limit_wd, #1
-	b.pl	L(loop_misaligned)
+	ldp	tmp1, tmp2, [src2], #16
+	LS_BK	mask, mask, neg_offset
+	and	neg_offset, neg_offset, #63	/* Need actual value for cmp later. */
+	/* Skip the first compare if data in tmp1 is irrelevant. */
+	tbnz	offset, 6, L(misaligned_mid_loop)
 
-L(done_loop):
-	/* We found a difference or a NULL before the limit was reached.  */
-	and	limit, limit, #7
-	cbz	limit, L(not_limit)
-	/* Read the last word.  */
-	sub	src1, src1, 8
-	sub	src2, src2, 8
-	ldr	data1, [src1, limit]
-	ldr	data2, [src2, limit]
-	sub	tmp1, data1, zeroones
-	orr	tmp2, data1, #REP8_7f
+L(loop_misaligned):
+	/* STEP_A: Compare full 8 bytes when there is enough data from SRC2.*/
+	LS_FW	data2, tmp1, offset
+	LS_BK	tmp1, tmp2, neg_offset
+	subs	limit, limit, #8
+	orr	data2, data2, tmp1	/* 8 bytes from SRC2 combined from two regs.*/
+	sub	has_nul, data1, zeroones
 	eor	diff, data1, data2	/* Non-zero if differences found.  */
-	bics	has_nul, tmp1, tmp2	/* Non-zero if NUL terminator.  */
-	ccmp	diff, #0, #0, eq
-	b.ne	L(not_limit)
+	orr	tmp3, data1, #REP8_7f
+	csinv	endloop, diff, xzr, hi	/* If limit, set to all ones. */
+	bic	has_nul, has_nul, tmp3	/* Non-zero if NUL byte found in SRC1. */
+	orr	tmp3, endloop, has_nul
+	cbnz	tmp3, L(full_check)
+
+	ldr	data1, [src1], #8
+L(misaligned_mid_loop):
+	/* STEP_B: Compare first part of data1 to second part of tmp2. */
+	LS_FW	data2, tmp2, offset
+#ifdef __AARCH64EB__
+	/* For big-endian we do a byte reverse to avoid carry-propagation
+	problem described above. This way we can reuse the has_nul in the
+	next step and also use syndrome value trick at the end. */
+	rev	tmp3, data1
+	#define data1_fixed tmp3
+#else
+	#define data1_fixed data1
+#endif
+	sub	has_nul, data1_fixed, zeroones
+	orr	tmp3, data1_fixed, #REP8_7f
+	eor	diff, data2, data1	/* Non-zero if differences found.  */
+	bic	has_nul, has_nul, tmp3	/* Non-zero if NUL terminator.  */
+#ifdef __AARCH64EB__
+	rev	has_nul, has_nul
+#endif
+	cmp	limit, neg_offset, lsr #3
+	orr	syndrome, diff, has_nul
+	bic	syndrome, syndrome, mask	/* Ignore later bytes. */
+	csinv	tmp3, syndrome, xzr, hi	/* If limit, set to all ones. */
+	cbnz	tmp3, L(syndrome_check)
+
+	/* STEP_C: Compare second part of data1 to first part of tmp1. */
+	ldp	tmp1, tmp2, [src2], #16
+	cmp	limit, #8
+	LS_BK	data2, tmp1, neg_offset
+	eor	diff, data2, data1	/* Non-zero if differences found.  */
+	orr	syndrome, diff, has_nul
+	and	syndrome, syndrome, mask	/* Ignore earlier bytes. */
+	csinv	tmp3, syndrome, xzr, hi	/* If limit, set to all ones. */
+	cbnz	tmp3, L(syndrome_check)
+
+	ldr	data1, [src1], #8
+	sub	limit, limit, #8
+	b	L(loop_misaligned)
+
+#ifdef	__AARCH64EB__
+L(syndrome_check):
+	clz	pos, syndrome
+	cmp	pos, limit, lsl #3
+	b.lo	L(end_quick)
+#endif
 
 L(ret0):
 	mov	result, #0
 	ret
-
-SYM_FUNC_END_PI(strncmp)
-EXPORT_SYMBOL_NOHWKASAN(strncmp)
+SYM_FUNC_END(__pi_strncmp)
+SYM_FUNC_ALIAS_WEAK(strncmp, __pi_strncmp)
+EXPORT_SYMBOL_NOKASAN(strncmp)
diff --git a/arch/arm64/lib/strnlen.S b/arch/arm64/lib/strnlen.S
index b72913a99038..d5ac0e10a01d 100644
--- a/arch/arm64/lib/strnlen.S
+++ b/arch/arm64/lib/strnlen.S
@@ -47,7 +47,7 @@ limit_wd	.req	x14
 #define REP8_7f 0x7f7f7f7f7f7f7f7f
 #define REP8_80 0x8080808080808080
 
-SYM_FUNC_START_WEAK_PI(strnlen)
+SYM_FUNC_START(__pi_strnlen)
 	cbz	limit, .Lhit_limit
 	mov	zeroones, #REP8_01
 	bic	src, srcin, #15
@@ -156,5 +156,7 @@ CPU_LE( lsr	tmp2, tmp2, tmp4 )	/* Shift (tmp1 & 63).  */
 .Lhit_limit:
 	mov	len, limit
 	ret
-SYM_FUNC_END_PI(strnlen)
+SYM_FUNC_END(__pi_strnlen)
+
+SYM_FUNC_ALIAS_WEAK(strnlen, __pi_strnlen)
 EXPORT_SYMBOL_NOKASAN(strnlen)
diff --git a/arch/arm64/lib/strrchr.S b/arch/arm64/lib/strrchr.S
index 13132d1ed6d1..a5123cf0ce12 100644
--- a/arch/arm64/lib/strrchr.S
+++ b/arch/arm64/lib/strrchr.S
@@ -18,7 +18,7 @@
  * Returns:
  *	x0 - address of last occurrence of 'c' or 0
  */
-SYM_FUNC_START_WEAK_PI(strrchr)
+SYM_FUNC_START(__pi_strrchr)
 	mov	x3, #0
 	and	w1, w1, #0xff
 1:	ldrb	w2, [x0], #1
@@ -29,5 +29,6 @@ SYM_FUNC_START_WEAK_PI(strrchr)
 	b	1b
 2:	mov	x0, x3
 	ret
-SYM_FUNC_END_PI(strrchr)
+SYM_FUNC_END(__pi_strrchr)
+SYM_FUNC_ALIAS_WEAK(strrchr, __pi_strrchr)
 EXPORT_SYMBOL_NOKASAN(strrchr)
diff --git a/arch/arm64/lib/xor-neon.c b/arch/arm64/lib/xor-neon.c
index 11bf4f8aca68..96b171995d19 100644
--- a/arch/arm64/lib/xor-neon.c
+++ b/arch/arm64/lib/xor-neon.c
@@ -10,8 +10,8 @@
 #include <linux/module.h>
 #include <asm/neon-intrinsics.h>
 
-void xor_arm64_neon_2(unsigned long bytes, unsigned long *p1,
-	unsigned long *p2)
+void xor_arm64_neon_2(unsigned long bytes, unsigned long * __restrict p1,
+	const unsigned long * __restrict p2)
 {
 	uint64_t *dp1 = (uint64_t *)p1;
 	uint64_t *dp2 = (uint64_t *)p2;
@@ -37,8 +37,9 @@ void xor_arm64_neon_2(unsigned long bytes, unsigned long *p1,
 	} while (--lines > 0);
 }
 
-void xor_arm64_neon_3(unsigned long bytes, unsigned long *p1,
-	unsigned long *p2, unsigned long *p3)
+void xor_arm64_neon_3(unsigned long bytes, unsigned long * __restrict p1,
+	const unsigned long * __restrict p2,
+	const unsigned long * __restrict p3)
 {
 	uint64_t *dp1 = (uint64_t *)p1;
 	uint64_t *dp2 = (uint64_t *)p2;
@@ -72,8 +73,10 @@ void xor_arm64_neon_3(unsigned long bytes, unsigned long *p1,
 	} while (--lines > 0);
 }
 
-void xor_arm64_neon_4(unsigned long bytes, unsigned long *p1,
-	unsigned long *p2, unsigned long *p3, unsigned long *p4)
+void xor_arm64_neon_4(unsigned long bytes, unsigned long * __restrict p1,
+	const unsigned long * __restrict p2,
+	const unsigned long * __restrict p3,
+	const unsigned long * __restrict p4)
 {
 	uint64_t *dp1 = (uint64_t *)p1;
 	uint64_t *dp2 = (uint64_t *)p2;
@@ -115,9 +118,11 @@ void xor_arm64_neon_4(unsigned long bytes, unsigned long *p1,
 	} while (--lines > 0);
 }
 
-void xor_arm64_neon_5(unsigned long bytes, unsigned long *p1,
-	unsigned long *p2, unsigned long *p3,
-	unsigned long *p4, unsigned long *p5)
+void xor_arm64_neon_5(unsigned long bytes, unsigned long * __restrict p1,
+	const unsigned long * __restrict p2,
+	const unsigned long * __restrict p3,
+	const unsigned long * __restrict p4,
+	const unsigned long * __restrict p5)
 {
 	uint64_t *dp1 = (uint64_t *)p1;
 	uint64_t *dp2 = (uint64_t *)p2;
@@ -167,7 +172,7 @@ void xor_arm64_neon_5(unsigned long bytes, unsigned long *p1,
 	} while (--lines > 0);
 }
 
-struct xor_block_template const xor_block_inner_neon = {
+struct xor_block_template xor_block_inner_neon __ro_after_init = {
 	.name	= "__inner_neon__",
 	.do_2	= xor_arm64_neon_2,
 	.do_3	= xor_arm64_neon_3,
@@ -176,6 +181,158 @@ struct xor_block_template const xor_block_inner_neon = {
 };
 EXPORT_SYMBOL(xor_block_inner_neon);
 
+static inline uint64x2_t eor3(uint64x2_t p, uint64x2_t q, uint64x2_t r)
+{
+	uint64x2_t res;
+
+	asm(ARM64_ASM_PREAMBLE ".arch_extension sha3\n"
+	    "eor3 %0.16b, %1.16b, %2.16b, %3.16b"
+	    : "=w"(res) : "w"(p), "w"(q), "w"(r));
+	return res;
+}
+
+static void xor_arm64_eor3_3(unsigned long bytes,
+	unsigned long * __restrict p1,
+	const unsigned long * __restrict p2,
+	const unsigned long * __restrict p3)
+{
+	uint64_t *dp1 = (uint64_t *)p1;
+	uint64_t *dp2 = (uint64_t *)p2;
+	uint64_t *dp3 = (uint64_t *)p3;
+
+	register uint64x2_t v0, v1, v2, v3;
+	long lines = bytes / (sizeof(uint64x2_t) * 4);
+
+	do {
+		/* p1 ^= p2 ^ p3 */
+		v0 = eor3(vld1q_u64(dp1 + 0), vld1q_u64(dp2 + 0),
+			  vld1q_u64(dp3 + 0));
+		v1 = eor3(vld1q_u64(dp1 + 2), vld1q_u64(dp2 + 2),
+			  vld1q_u64(dp3 + 2));
+		v2 = eor3(vld1q_u64(dp1 + 4), vld1q_u64(dp2 + 4),
+			  vld1q_u64(dp3 + 4));
+		v3 = eor3(vld1q_u64(dp1 + 6), vld1q_u64(dp2 + 6),
+			  vld1q_u64(dp3 + 6));
+
+		/* store */
+		vst1q_u64(dp1 + 0, v0);
+		vst1q_u64(dp1 + 2, v1);
+		vst1q_u64(dp1 + 4, v2);
+		vst1q_u64(dp1 + 6, v3);
+
+		dp1 += 8;
+		dp2 += 8;
+		dp3 += 8;
+	} while (--lines > 0);
+}
+
+static void xor_arm64_eor3_4(unsigned long bytes,
+	unsigned long * __restrict p1,
+	const unsigned long * __restrict p2,
+	const unsigned long * __restrict p3,
+	const unsigned long * __restrict p4)
+{
+	uint64_t *dp1 = (uint64_t *)p1;
+	uint64_t *dp2 = (uint64_t *)p2;
+	uint64_t *dp3 = (uint64_t *)p3;
+	uint64_t *dp4 = (uint64_t *)p4;
+
+	register uint64x2_t v0, v1, v2, v3;
+	long lines = bytes / (sizeof(uint64x2_t) * 4);
+
+	do {
+		/* p1 ^= p2 ^ p3 */
+		v0 = eor3(vld1q_u64(dp1 + 0), vld1q_u64(dp2 + 0),
+			  vld1q_u64(dp3 + 0));
+		v1 = eor3(vld1q_u64(dp1 + 2), vld1q_u64(dp2 + 2),
+			  vld1q_u64(dp3 + 2));
+		v2 = eor3(vld1q_u64(dp1 + 4), vld1q_u64(dp2 + 4),
+			  vld1q_u64(dp3 + 4));
+		v3 = eor3(vld1q_u64(dp1 + 6), vld1q_u64(dp2 + 6),
+			  vld1q_u64(dp3 + 6));
+
+		/* p1 ^= p4 */
+		v0 = veorq_u64(v0, vld1q_u64(dp4 + 0));
+		v1 = veorq_u64(v1, vld1q_u64(dp4 + 2));
+		v2 = veorq_u64(v2, vld1q_u64(dp4 + 4));
+		v3 = veorq_u64(v3, vld1q_u64(dp4 + 6));
+
+		/* store */
+		vst1q_u64(dp1 + 0, v0);
+		vst1q_u64(dp1 + 2, v1);
+		vst1q_u64(dp1 + 4, v2);
+		vst1q_u64(dp1 + 6, v3);
+
+		dp1 += 8;
+		dp2 += 8;
+		dp3 += 8;
+		dp4 += 8;
+	} while (--lines > 0);
+}
+
+static void xor_arm64_eor3_5(unsigned long bytes,
+	unsigned long * __restrict p1,
+	const unsigned long * __restrict p2,
+	const unsigned long * __restrict p3,
+	const unsigned long * __restrict p4,
+	const unsigned long * __restrict p5)
+{
+	uint64_t *dp1 = (uint64_t *)p1;
+	uint64_t *dp2 = (uint64_t *)p2;
+	uint64_t *dp3 = (uint64_t *)p3;
+	uint64_t *dp4 = (uint64_t *)p4;
+	uint64_t *dp5 = (uint64_t *)p5;
+
+	register uint64x2_t v0, v1, v2, v3;
+	long lines = bytes / (sizeof(uint64x2_t) * 4);
+
+	do {
+		/* p1 ^= p2 ^ p3 */
+		v0 = eor3(vld1q_u64(dp1 + 0), vld1q_u64(dp2 + 0),
+			  vld1q_u64(dp3 + 0));
+		v1 = eor3(vld1q_u64(dp1 + 2), vld1q_u64(dp2 + 2),
+			  vld1q_u64(dp3 + 2));
+		v2 = eor3(vld1q_u64(dp1 + 4), vld1q_u64(dp2 + 4),
+			  vld1q_u64(dp3 + 4));
+		v3 = eor3(vld1q_u64(dp1 + 6), vld1q_u64(dp2 + 6),
+			  vld1q_u64(dp3 + 6));
+
+		/* p1 ^= p4 ^ p5 */
+		v0 = eor3(v0, vld1q_u64(dp4 + 0), vld1q_u64(dp5 + 0));
+		v1 = eor3(v1, vld1q_u64(dp4 + 2), vld1q_u64(dp5 + 2));
+		v2 = eor3(v2, vld1q_u64(dp4 + 4), vld1q_u64(dp5 + 4));
+		v3 = eor3(v3, vld1q_u64(dp4 + 6), vld1q_u64(dp5 + 6));
+
+		/* store */
+		vst1q_u64(dp1 + 0, v0);
+		vst1q_u64(dp1 + 2, v1);
+		vst1q_u64(dp1 + 4, v2);
+		vst1q_u64(dp1 + 6, v3);
+
+		dp1 += 8;
+		dp2 += 8;
+		dp3 += 8;
+		dp4 += 8;
+		dp5 += 8;
+	} while (--lines > 0);
+}
+
+static int __init xor_neon_init(void)
+{
+	if (IS_ENABLED(CONFIG_AS_HAS_SHA3) && cpu_have_named_feature(SHA3)) {
+		xor_block_inner_neon.do_3 = xor_arm64_eor3_3;
+		xor_block_inner_neon.do_4 = xor_arm64_eor3_4;
+		xor_block_inner_neon.do_5 = xor_arm64_eor3_5;
+	}
+	return 0;
+}
+module_init(xor_neon_init);
+
+static void __exit xor_neon_exit(void)
+{
+}
+module_exit(xor_neon_exit);
+
 MODULE_AUTHOR("Jackie Liu <liuyun01@kylinos.cn>");
 MODULE_DESCRIPTION("ARMv8 XOR Extensions");
 MODULE_LICENSE("GPL");
diff --git a/arch/arm64/mm/cache.S b/arch/arm64/mm/cache.S
index 5051b3c1a4f1..081058d4e436 100644
--- a/arch/arm64/mm/cache.S
+++ b/arch/arm64/mm/cache.S
@@ -107,10 +107,11 @@ SYM_FUNC_END(icache_inval_pou)
  *	- start   - virtual start address of region
  *	- end     - virtual end address of region
  */
-SYM_FUNC_START_PI(dcache_clean_inval_poc)
+SYM_FUNC_START(__pi_dcache_clean_inval_poc)
 	dcache_by_line_op civac, sy, x0, x1, x2, x3
 	ret
-SYM_FUNC_END_PI(dcache_clean_inval_poc)
+SYM_FUNC_END(__pi_dcache_clean_inval_poc)
+SYM_FUNC_ALIAS(dcache_clean_inval_poc, __pi_dcache_clean_inval_poc)
 
 /*
  *	dcache_clean_pou(start, end)
@@ -140,15 +141,7 @@ SYM_FUNC_END(dcache_clean_pou)
  *	- start   - kernel start address of region
  *	- end     - kernel end address of region
  */
-SYM_FUNC_START_LOCAL(__dma_inv_area)
-SYM_FUNC_START_PI(dcache_inval_poc)
-	/* FALLTHROUGH */
-
-/*
- *	__dma_inv_area(start, end)
- *	- start   - virtual start address of region
- *	- end     - virtual end address of region
- */
+SYM_FUNC_START(__pi_dcache_inval_poc)
 	dcache_line_size x2, x3
 	sub	x3, x2, #1
 	tst	x1, x3				// end cache line aligned?
@@ -166,8 +159,8 @@ SYM_FUNC_START_PI(dcache_inval_poc)
 	b.lo	2b
 	dsb	sy
 	ret
-SYM_FUNC_END_PI(dcache_inval_poc)
-SYM_FUNC_END(__dma_inv_area)
+SYM_FUNC_END(__pi_dcache_inval_poc)
+SYM_FUNC_ALIAS(dcache_inval_poc, __pi_dcache_inval_poc)
 
 /*
  *	dcache_clean_poc(start, end)
@@ -178,19 +171,11 @@ SYM_FUNC_END(__dma_inv_area)
  *	- start   - virtual start address of region
  *	- end     - virtual end address of region
  */
-SYM_FUNC_START_LOCAL(__dma_clean_area)
-SYM_FUNC_START_PI(dcache_clean_poc)
-	/* FALLTHROUGH */
-
-/*
- *	__dma_clean_area(start, end)
- *	- start   - virtual start address of region
- *	- end     - virtual end address of region
- */
+SYM_FUNC_START(__pi_dcache_clean_poc)
 	dcache_by_line_op cvac, sy, x0, x1, x2, x3
 	ret
-SYM_FUNC_END_PI(dcache_clean_poc)
-SYM_FUNC_END(__dma_clean_area)
+SYM_FUNC_END(__pi_dcache_clean_poc)
+SYM_FUNC_ALIAS(dcache_clean_poc, __pi_dcache_clean_poc)
 
 /*
  *	dcache_clean_pop(start, end)
@@ -201,50 +186,11 @@ SYM_FUNC_END(__dma_clean_area)
  *	- start   - virtual start address of region
  *	- end     - virtual end address of region
  */
-SYM_FUNC_START_PI(dcache_clean_pop)
+SYM_FUNC_START(__pi_dcache_clean_pop)
 	alternative_if_not ARM64_HAS_DCPOP
 	b	dcache_clean_poc
 	alternative_else_nop_endif
 	dcache_by_line_op cvap, sy, x0, x1, x2, x3
 	ret
-SYM_FUNC_END_PI(dcache_clean_pop)
-
-/*
- *	__dma_flush_area(start, size)
- *
- *	clean & invalidate D / U line
- *
- *	- start   - virtual start address of region
- *	- size    - size in question
- */
-SYM_FUNC_START_PI(__dma_flush_area)
-	add	x1, x0, x1
-	dcache_by_line_op civac, sy, x0, x1, x2, x3
-	ret
-SYM_FUNC_END_PI(__dma_flush_area)
-
-/*
- *	__dma_map_area(start, size, dir)
- *	- start	- kernel virtual start address
- *	- size	- size of region
- *	- dir	- DMA direction
- */
-SYM_FUNC_START_PI(__dma_map_area)
-	add	x1, x0, x1
-	cmp	w2, #DMA_FROM_DEVICE
-	b.eq	__dma_inv_area
-	b	__dma_clean_area
-SYM_FUNC_END_PI(__dma_map_area)
-
-/*
- *	__dma_unmap_area(start, size, dir)
- *	- start	- kernel virtual start address
- *	- size	- size of region
- *	- dir	- DMA direction
- */
-SYM_FUNC_START_PI(__dma_unmap_area)
-	add	x1, x0, x1
-	cmp	w2, #DMA_TO_DEVICE
-	b.ne	__dma_inv_area
-	ret
-SYM_FUNC_END_PI(__dma_unmap_area)
+SYM_FUNC_END(__pi_dcache_clean_pop)
+SYM_FUNC_ALIAS(dcache_clean_pop, __pi_dcache_clean_pop)
diff --git a/arch/arm64/mm/context.c b/arch/arm64/mm/context.c
index cd72576ae2b7..e1e0dca01839 100644
--- a/arch/arm64/mm/context.c
+++ b/arch/arm64/mm/context.c
@@ -35,25 +35,25 @@ static unsigned long *pinned_asid_map;
 #define ASID_FIRST_VERSION	(1UL << asid_bits)
 
 #define NUM_USER_ASIDS		ASID_FIRST_VERSION
-#define asid2idx(asid)		((asid) & ~ASID_MASK)
-#define idx2asid(idx)		asid2idx(idx)
+#define ctxid2asid(asid)	((asid) & ~ASID_MASK)
+#define asid2ctxid(asid, genid)	((asid) | (genid))
 
 /* Get the ASIDBits supported by the current CPU */
 static u32 get_cpu_asid_bits(void)
 {
 	u32 asid;
 	int fld = cpuid_feature_extract_unsigned_field(read_cpuid(ID_AA64MMFR0_EL1),
-						ID_AA64MMFR0_ASID_SHIFT);
+						ID_AA64MMFR0_EL1_ASIDBITS_SHIFT);
 
 	switch (fld) {
 	default:
 		pr_warn("CPU%d: Unknown ASID size (%d); assuming 8-bit\n",
 					smp_processor_id(),  fld);
 		fallthrough;
-	case 0:
+	case ID_AA64MMFR0_EL1_ASIDBITS_8:
 		asid = 8;
 		break;
-	case 2:
+	case ID_AA64MMFR0_EL1_ASIDBITS_16:
 		asid = 16;
 	}
 
@@ -120,7 +120,7 @@ static void flush_context(void)
 		 */
 		if (asid == 0)
 			asid = per_cpu(reserved_asids, i);
-		__set_bit(asid2idx(asid), asid_map);
+		__set_bit(ctxid2asid(asid), asid_map);
 		per_cpu(reserved_asids, i) = asid;
 	}
 
@@ -162,7 +162,7 @@ static u64 new_context(struct mm_struct *mm)
 	u64 generation = atomic64_read(&asid_generation);
 
 	if (asid != 0) {
-		u64 newasid = generation | (asid & ~ASID_MASK);
+		u64 newasid = asid2ctxid(ctxid2asid(asid), generation);
 
 		/*
 		 * If our current ASID was active during a rollover, we
@@ -183,7 +183,7 @@ static u64 new_context(struct mm_struct *mm)
 		 * We had a valid ASID in a previous life, so try to re-use
 		 * it if possible.
 		 */
-		if (!__test_and_set_bit(asid2idx(asid), asid_map))
+		if (!__test_and_set_bit(ctxid2asid(asid), asid_map))
 			return newasid;
 	}
 
@@ -209,7 +209,7 @@ static u64 new_context(struct mm_struct *mm)
 set_asid:
 	__set_bit(asid, asid_map);
 	cur_idx = asid;
-	return idx2asid(asid) | generation;
+	return asid2ctxid(asid, generation);
 }
 
 void check_and_switch_context(struct mm_struct *mm)
@@ -300,13 +300,13 @@ unsigned long arm64_mm_context_get(struct mm_struct *mm)
 	}
 
 	nr_pinned_asids++;
-	__set_bit(asid2idx(asid), pinned_asid_map);
+	__set_bit(ctxid2asid(asid), pinned_asid_map);
 	refcount_set(&mm->context.pinned, 1);
 
 out_unlock:
 	raw_spin_unlock_irqrestore(&cpu_asid_lock, flags);
 
-	asid &= ~ASID_MASK;
+	asid = ctxid2asid(asid);
 
 	/* Set the equivalent of USER_ASID_BIT */
 	if (asid && arm64_kernel_unmapped_at_el0())
@@ -327,7 +327,7 @@ void arm64_mm_context_put(struct mm_struct *mm)
 	raw_spin_lock_irqsave(&cpu_asid_lock, flags);
 
 	if (refcount_dec_and_test(&mm->context.pinned)) {
-		__clear_bit(asid2idx(asid), pinned_asid_map);
+		__clear_bit(ctxid2asid(asid), pinned_asid_map);
 		nr_pinned_asids--;
 	}
 
diff --git a/arch/arm64/mm/copypage.c b/arch/arm64/mm/copypage.c
index b5447e53cd73..24913271e898 100644
--- a/arch/arm64/mm/copypage.c
+++ b/arch/arm64/mm/copypage.c
@@ -16,22 +16,13 @@
 
 void copy_highpage(struct page *to, struct page *from)
 {
-	struct page *kto = page_address(to);
-	struct page *kfrom = page_address(from);
+	void *kto = page_address(to);
+	void *kfrom = page_address(from);
 
 	copy_page(kto, kfrom);
 
 	if (system_supports_mte() && test_bit(PG_mte_tagged, &from->flags)) {
 		set_bit(PG_mte_tagged, &to->flags);
-		page_kasan_tag_reset(to);
-		/*
-		 * We need smp_wmb() in between setting the flags and clearing the
-		 * tags because if another thread reads page->flags and builds a
-		 * tagged address out of it, there is an actual dependency to the
-		 * memory access, but on the current thread we do not guarantee that
-		 * the new page->flags are visible before the tags were updated.
-		 */
-		smp_wmb();
 		mte_copy_page_tags(kto, kfrom);
 	}
 }
diff --git a/arch/arm64/mm/dma-mapping.c b/arch/arm64/mm/dma-mapping.c
index 6719f9efea09..3cb101e8cb29 100644
--- a/arch/arm64/mm/dma-mapping.c
+++ b/arch/arm64/mm/dma-mapping.c
@@ -7,27 +7,36 @@
 #include <linux/gfp.h>
 #include <linux/cache.h>
 #include <linux/dma-map-ops.h>
-#include <linux/dma-iommu.h>
+#include <linux/iommu.h>
 #include <xen/xen.h>
-#include <xen/swiotlb-xen.h>
 
 #include <asm/cacheflush.h>
+#include <asm/xen/xen-ops.h>
 
 void arch_sync_dma_for_device(phys_addr_t paddr, size_t size,
-		enum dma_data_direction dir)
+			      enum dma_data_direction dir)
 {
-	__dma_map_area(phys_to_virt(paddr), size, dir);
+	unsigned long start = (unsigned long)phys_to_virt(paddr);
+
+	dcache_clean_poc(start, start + size);
 }
 
 void arch_sync_dma_for_cpu(phys_addr_t paddr, size_t size,
-		enum dma_data_direction dir)
+			   enum dma_data_direction dir)
 {
-	__dma_unmap_area(phys_to_virt(paddr), size, dir);
+	unsigned long start = (unsigned long)phys_to_virt(paddr);
+
+	if (dir == DMA_TO_DEVICE)
+		return;
+
+	dcache_inval_poc(start, start + size);
 }
 
 void arch_dma_prep_coherent(struct page *page, size_t size)
 {
-	__dma_flush_area(page_address(page), size);
+	unsigned long start = (unsigned long)page_address(page);
+
+	dcache_clean_poc(start, start + size);
 }
 
 #ifdef CONFIG_IOMMU_DMA
@@ -52,8 +61,5 @@ void arch_setup_dma_ops(struct device *dev, u64 dma_base, u64 size,
 	if (iommu)
 		iommu_setup_dma_ops(dev, dma_base, dma_base + size - 1);
 
-#ifdef CONFIG_XEN
-	if (xen_swiotlb_detect())
-		dev->dma_ops = &xen_swiotlb_dma_ops;
-#endif
+	xen_setup_dma_ops(dev);
 }
diff --git a/arch/arm64/mm/extable.c b/arch/arm64/mm/extable.c
index c3d53811a15e..228d681a8715 100644
--- a/arch/arm64/mm/extable.c
+++ b/arch/arm64/mm/extable.c
@@ -10,22 +10,12 @@
 #include <asm/asm-extable.h>
 #include <asm/ptrace.h>
 
-typedef bool (*ex_handler_t)(const struct exception_table_entry *,
-			     struct pt_regs *);
-
 static inline unsigned long
 get_ex_fixup(const struct exception_table_entry *ex)
 {
 	return ((unsigned long)&ex->fixup + ex->fixup);
 }
 
-static bool ex_handler_fixup(const struct exception_table_entry *ex,
-			     struct pt_regs *regs)
-{
-	regs->pc = get_ex_fixup(ex);
-	return true;
-}
-
 static bool ex_handler_uaccess_err_zero(const struct exception_table_entry *ex,
 					struct pt_regs *regs)
 {
@@ -43,8 +33,8 @@ static bool
 ex_handler_load_unaligned_zeropad(const struct exception_table_entry *ex,
 				  struct pt_regs *regs)
 {
-	int reg_data = FIELD_GET(EX_DATA_REG_DATA, ex->type);
-	int reg_addr = FIELD_GET(EX_DATA_REG_ADDR, ex->type);
+	int reg_data = FIELD_GET(EX_DATA_REG_DATA, ex->data);
+	int reg_addr = FIELD_GET(EX_DATA_REG_ADDR, ex->data);
 	unsigned long data, addr, offset;
 
 	addr = pt_regs_read_reg(regs, reg_addr);
@@ -75,11 +65,10 @@ bool fixup_exception(struct pt_regs *regs)
 		return false;
 
 	switch (ex->type) {
-	case EX_TYPE_FIXUP:
-		return ex_handler_fixup(ex, regs);
 	case EX_TYPE_BPF:
 		return ex_handler_bpf(ex, regs);
 	case EX_TYPE_UACCESS_ERR_ZERO:
+	case EX_TYPE_KACCESS_ERR_ZERO:
 		return ex_handler_uaccess_err_zero(ex, regs);
 	case EX_TYPE_LOAD_UNALIGNED_ZEROPAD:
 		return ex_handler_load_unaligned_zeropad(ex, regs);
diff --git a/arch/arm64/mm/fault.c b/arch/arm64/mm/fault.c
index 9ae24e3b72be..3e9cf9826417 100644
--- a/arch/arm64/mm/fault.c
+++ b/arch/arm64/mm/fault.c
@@ -30,6 +30,7 @@
 #include <asm/bug.h>
 #include <asm/cmpxchg.h>
 #include <asm/cpufeature.h>
+#include <asm/efi.h>
 #include <asm/exception.h>
 #include <asm/daifflags.h>
 #include <asm/debug-monitors.h>
@@ -43,7 +44,7 @@
 #include <asm/traps.h>
 
 struct fault_info {
-	int	(*fn)(unsigned long far, unsigned int esr,
+	int	(*fn)(unsigned long far, unsigned long esr,
 		      struct pt_regs *regs);
 	int	sig;
 	int	code;
@@ -53,17 +54,17 @@ struct fault_info {
 static const struct fault_info fault_info[];
 static struct fault_info debug_fault_info[];
 
-static inline const struct fault_info *esr_to_fault_info(unsigned int esr)
+static inline const struct fault_info *esr_to_fault_info(unsigned long esr)
 {
 	return fault_info + (esr & ESR_ELx_FSC);
 }
 
-static inline const struct fault_info *esr_to_debug_fault_info(unsigned int esr)
+static inline const struct fault_info *esr_to_debug_fault_info(unsigned long esr)
 {
 	return debug_fault_info + DBG_ESR_EVT(esr);
 }
 
-static void data_abort_decode(unsigned int esr)
+static void data_abort_decode(unsigned long esr)
 {
 	pr_alert("Data abort info:\n");
 
@@ -85,11 +86,11 @@ static void data_abort_decode(unsigned int esr)
 		 (esr & ESR_ELx_WNR) >> ESR_ELx_WNR_SHIFT);
 }
 
-static void mem_abort_decode(unsigned int esr)
+static void mem_abort_decode(unsigned long esr)
 {
 	pr_alert("Mem abort info:\n");
 
-	pr_alert("  ESR = 0x%08x\n", esr);
+	pr_alert("  ESR = 0x%016lx\n", esr);
 	pr_alert("  EC = 0x%02lx: %s, IL = %u bits\n",
 		 ESR_ELx_EC(esr), esr_get_class_string(esr),
 		 (esr & ESR_ELx_IL) ? 32 : 16);
@@ -99,7 +100,7 @@ static void mem_abort_decode(unsigned int esr)
 	pr_alert("  EA = %lu, S1PTW = %lu\n",
 		 (esr & ESR_ELx_EA) >> ESR_ELx_EA_SHIFT,
 		 (esr & ESR_ELx_S1PTW) >> ESR_ELx_S1PTW_SHIFT);
-	pr_alert("  FSC = 0x%02x: %s\n", (esr & ESR_ELx_FSC),
+	pr_alert("  FSC = 0x%02lx: %s\n", (esr & ESR_ELx_FSC),
 		 esr_to_fault_info(esr)->name);
 
 	if (esr_is_data_abort(esr))
@@ -229,20 +230,20 @@ int ptep_set_access_flags(struct vm_area_struct *vma,
 	return 1;
 }
 
-static bool is_el1_instruction_abort(unsigned int esr)
+static bool is_el1_instruction_abort(unsigned long esr)
 {
 	return ESR_ELx_EC(esr) == ESR_ELx_EC_IABT_CUR;
 }
 
-static bool is_el1_data_abort(unsigned int esr)
+static bool is_el1_data_abort(unsigned long esr)
 {
 	return ESR_ELx_EC(esr) == ESR_ELx_EC_DABT_CUR;
 }
 
-static inline bool is_el1_permission_fault(unsigned long addr, unsigned int esr,
+static inline bool is_el1_permission_fault(unsigned long addr, unsigned long esr,
 					   struct pt_regs *regs)
 {
-	unsigned int fsc_type = esr & ESR_ELx_FSC_TYPE;
+	unsigned long fsc_type = esr & ESR_ELx_FSC_TYPE;
 
 	if (!is_el1_data_abort(esr) && !is_el1_instruction_abort(esr))
 		return false;
@@ -258,7 +259,7 @@ static inline bool is_el1_permission_fault(unsigned long addr, unsigned int esr,
 }
 
 static bool __kprobes is_spurious_el1_translation_fault(unsigned long addr,
-							unsigned int esr,
+							unsigned long esr,
 							struct pt_regs *regs)
 {
 	unsigned long flags;
@@ -290,23 +291,25 @@ static bool __kprobes is_spurious_el1_translation_fault(unsigned long addr,
 }
 
 static void die_kernel_fault(const char *msg, unsigned long addr,
-			     unsigned int esr, struct pt_regs *regs)
+			     unsigned long esr, struct pt_regs *regs)
 {
 	bust_spinlocks(1);
 
 	pr_alert("Unable to handle kernel %s at virtual address %016lx\n", msg,
 		 addr);
 
+	kasan_non_canonical_hook(addr);
+
 	mem_abort_decode(esr);
 
 	show_pte(addr);
 	die("Oops", regs, esr);
 	bust_spinlocks(0);
-	do_exit(SIGKILL);
+	make_task_dead(SIGKILL);
 }
 
 #ifdef CONFIG_KASAN_HW_TAGS
-static void report_tag_fault(unsigned long addr, unsigned int esr,
+static void report_tag_fault(unsigned long addr, unsigned long esr,
 			     struct pt_regs *regs)
 {
 	/*
@@ -318,11 +321,11 @@ static void report_tag_fault(unsigned long addr, unsigned int esr,
 }
 #else
 /* Tag faults aren't enabled without CONFIG_KASAN_HW_TAGS. */
-static inline void report_tag_fault(unsigned long addr, unsigned int esr,
+static inline void report_tag_fault(unsigned long addr, unsigned long esr,
 				    struct pt_regs *regs) { }
 #endif
 
-static void do_tag_recovery(unsigned long addr, unsigned int esr,
+static void do_tag_recovery(unsigned long addr, unsigned long esr,
 			   struct pt_regs *regs)
 {
 
@@ -333,13 +336,14 @@ static void do_tag_recovery(unsigned long addr, unsigned int esr,
 	 * It will be done lazily on the other CPUs when they will hit a
 	 * tag fault.
 	 */
-	sysreg_clear_set(sctlr_el1, SCTLR_ELx_TCF_MASK, SCTLR_ELx_TCF_NONE);
+	sysreg_clear_set(sctlr_el1, SCTLR_EL1_TCF_MASK,
+			 SYS_FIELD_PREP_ENUM(SCTLR_EL1, TCF, NONE));
 	isb();
 }
 
-static bool is_el1_mte_sync_tag_check_fault(unsigned int esr)
+static bool is_el1_mte_sync_tag_check_fault(unsigned long esr)
 {
-	unsigned int fsc = esr & ESR_ELx_FSC;
+	unsigned long fsc = esr & ESR_ELx_FSC;
 
 	if (!is_el1_data_abort(esr))
 		return false;
@@ -350,7 +354,7 @@ static bool is_el1_mte_sync_tag_check_fault(unsigned int esr)
 	return false;
 }
 
-static void __do_kernel_fault(unsigned long addr, unsigned int esr,
+static void __do_kernel_fault(unsigned long addr, unsigned long esr,
 			      struct pt_regs *regs)
 {
 	const char *msg;
@@ -388,10 +392,13 @@ static void __do_kernel_fault(unsigned long addr, unsigned int esr,
 		msg = "paging request";
 	}
 
+	if (efi_runtime_fixup_exception(regs, msg))
+		return;
+
 	die_kernel_fault(msg, addr, esr, regs);
 }
 
-static void set_thread_esr(unsigned long address, unsigned int esr)
+static void set_thread_esr(unsigned long address, unsigned long esr)
 {
 	current->thread.fault_address = address;
 
@@ -439,7 +446,7 @@ static void set_thread_esr(unsigned long address, unsigned int esr)
 			 * exception level). Fail safe by not providing an ESR
 			 * context record at all.
 			 */
-			WARN(1, "ESR 0x%x is not DABT or IABT from EL0\n", esr);
+			WARN(1, "ESR 0x%lx is not DABT or IABT from EL0\n", esr);
 			esr = 0;
 			break;
 		}
@@ -448,7 +455,7 @@ static void set_thread_esr(unsigned long address, unsigned int esr)
 	current->thread.fault_code = esr;
 }
 
-static void do_bad_area(unsigned long far, unsigned int esr,
+static void do_bad_area(unsigned long far, unsigned long esr,
 			struct pt_regs *regs)
 {
 	unsigned long addr = untagged_addr(far);
@@ -499,7 +506,7 @@ static vm_fault_t __do_page_fault(struct mm_struct *mm, unsigned long addr,
 	return handle_mm_fault(vma, addr, mm_flags, regs);
 }
 
-static bool is_el0_instruction_abort(unsigned int esr)
+static bool is_el0_instruction_abort(unsigned long esr)
 {
 	return ESR_ELx_EC(esr) == ESR_ELx_EC_IABT_LOW;
 }
@@ -508,12 +515,12 @@ static bool is_el0_instruction_abort(unsigned int esr)
  * Note: not valid for EL1 DC IVAC, but we never use that such that it
  * should fault. EL0 cannot issue DC IVAC (undef).
  */
-static bool is_write_abort(unsigned int esr)
+static bool is_write_abort(unsigned long esr)
 {
 	return (esr & ESR_ELx_WNR) && !(esr & ESR_ELx_CM);
 }
 
-static int __kprobes do_page_fault(unsigned long far, unsigned int esr,
+static int __kprobes do_page_fault(unsigned long far, unsigned long esr,
 				   struct pt_regs *regs)
 {
 	const struct fault_info *inf;
@@ -605,11 +612,13 @@ retry:
 		return 0;
 	}
 
+	/* The fault is fully completed (including releasing mmap lock) */
+	if (fault & VM_FAULT_COMPLETED)
+		return 0;
+
 	if (fault & VM_FAULT_RETRY) {
-		if (mm_flags & FAULT_FLAG_ALLOW_RETRY) {
-			mm_flags |= FAULT_FLAG_TRIED;
-			goto retry;
-		}
+		mm_flags |= FAULT_FLAG_TRIED;
+		goto retry;
 	}
 	mmap_read_unlock(mm);
 
@@ -671,7 +680,7 @@ no_context:
 }
 
 static int __kprobes do_translation_fault(unsigned long far,
-					  unsigned int esr,
+					  unsigned long esr,
 					  struct pt_regs *regs)
 {
 	unsigned long addr = untagged_addr(far);
@@ -683,19 +692,22 @@ static int __kprobes do_translation_fault(unsigned long far,
 	return 0;
 }
 
-static int do_alignment_fault(unsigned long far, unsigned int esr,
+static int do_alignment_fault(unsigned long far, unsigned long esr,
 			      struct pt_regs *regs)
 {
+	if (IS_ENABLED(CONFIG_COMPAT_ALIGNMENT_FIXUPS) &&
+	    compat_user_mode(regs))
+		return do_compat_alignment_fixup(far, regs);
 	do_bad_area(far, esr, regs);
 	return 0;
 }
 
-static int do_bad(unsigned long far, unsigned int esr, struct pt_regs *regs)
+static int do_bad(unsigned long far, unsigned long esr, struct pt_regs *regs)
 {
 	return 1; /* "fault" */
 }
 
-static int do_sea(unsigned long far, unsigned int esr, struct pt_regs *regs)
+static int do_sea(unsigned long far, unsigned long esr, struct pt_regs *regs)
 {
 	const struct fault_info *inf;
 	unsigned long siaddr;
@@ -725,7 +737,7 @@ static int do_sea(unsigned long far, unsigned int esr, struct pt_regs *regs)
 	return 0;
 }
 
-static int do_tag_check_fault(unsigned long far, unsigned int esr,
+static int do_tag_check_fault(unsigned long far, unsigned long esr,
 			      struct pt_regs *regs)
 {
 	/*
@@ -805,7 +817,7 @@ static const struct fault_info fault_info[] = {
 	{ do_bad,		SIGKILL, SI_KERNEL,	"unknown 63"			},
 };
 
-void do_mem_abort(unsigned long far, unsigned int esr, struct pt_regs *regs)
+void do_mem_abort(unsigned long far, unsigned long esr, struct pt_regs *regs)
 {
 	const struct fault_info *inf = esr_to_fault_info(esr);
 	unsigned long addr = untagged_addr(far);
@@ -813,11 +825,8 @@ void do_mem_abort(unsigned long far, unsigned int esr, struct pt_regs *regs)
 	if (!inf->fn(far, esr, regs))
 		return;
 
-	if (!user_mode(regs)) {
-		pr_alert("Unhandled fault at 0x%016lx\n", addr);
-		mem_abort_decode(esr);
-		show_pte(addr);
-	}
+	if (!user_mode(regs))
+		die_kernel_fault(inf->name, addr, esr, regs);
 
 	/*
 	 * At this point we have an unrecognized fault type whose tag bits may
@@ -828,14 +837,14 @@ void do_mem_abort(unsigned long far, unsigned int esr, struct pt_regs *regs)
 }
 NOKPROBE_SYMBOL(do_mem_abort);
 
-void do_sp_pc_abort(unsigned long addr, unsigned int esr, struct pt_regs *regs)
+void do_sp_pc_abort(unsigned long addr, unsigned long esr, struct pt_regs *regs)
 {
 	arm64_notify_die("SP/PC alignment exception", regs, SIGBUS, BUS_ADRALN,
 			 addr, esr);
 }
 NOKPROBE_SYMBOL(do_sp_pc_abort);
 
-int __init early_brk64(unsigned long addr, unsigned int esr,
+int __init early_brk64(unsigned long addr, unsigned long esr,
 		       struct pt_regs *regs);
 
 /*
@@ -855,7 +864,7 @@ static struct fault_info __refdata debug_fault_info[] = {
 };
 
 void __init hook_debug_fault_code(int nr,
-				  int (*fn)(unsigned long, unsigned int, struct pt_regs *),
+				  int (*fn)(unsigned long, unsigned long, struct pt_regs *),
 				  int sig, int code, const char *name)
 {
 	BUG_ON(nr < 0 || nr >= ARRAY_SIZE(debug_fault_info));
@@ -888,7 +897,7 @@ static void debug_exception_exit(struct pt_regs *regs)
 }
 NOKPROBE_SYMBOL(debug_exception_exit);
 
-void do_debug_exception(unsigned long addr_if_watchpoint, unsigned int esr,
+void do_debug_exception(unsigned long addr_if_watchpoint, unsigned long esr,
 			struct pt_regs *regs)
 {
 	const struct fault_info *inf = esr_to_debug_fault_info(esr);
@@ -929,6 +938,5 @@ struct page *alloc_zeroed_user_highpage_movable(struct vm_area_struct *vma,
 void tag_clear_highpage(struct page *page)
 {
 	mte_zero_clear_page_tags(page_address(page));
-	page_kasan_tag_reset(page);
 	set_bit(PG_mte_tagged, &page->flags);
 }
diff --git a/arch/arm64/mm/flush.c b/arch/arm64/mm/flush.c
index 2aaf950b906c..5f9379b3c8c8 100644
--- a/arch/arm64/mm/flush.c
+++ b/arch/arm64/mm/flush.c
@@ -52,6 +52,13 @@ void __sync_icache_dcache(pte_t pte)
 {
 	struct page *page = pte_page(pte);
 
+	/*
+	 * HugeTLB pages are always fully mapped, so only setting head page's
+	 * PG_dcache_clean flag is enough.
+	 */
+	if (PageHuge(page))
+		page = compound_head(page);
+
 	if (!test_bit(PG_dcache_clean, &page->flags)) {
 		sync_icache_aliases((unsigned long)page_address(page),
 				    (unsigned long)page_address(page) +
@@ -68,6 +75,13 @@ EXPORT_SYMBOL_GPL(__sync_icache_dcache);
  */
 void flush_dcache_page(struct page *page)
 {
+	/*
+	 * HugeTLB pages are always fully mapped and only head page will be
+	 * set PG_dcache_clean (see comments in __sync_icache_dcache()).
+	 */
+	if (PageHuge(page))
+		page = compound_head(page);
+
 	if (test_bit(PG_dcache_clean, &page->flags))
 		clear_bit(PG_dcache_clean, &page->flags);
 }
diff --git a/arch/arm64/mm/hugetlbpage.c b/arch/arm64/mm/hugetlbpage.c
index ffb9c229610a..35e9a468d13e 100644
--- a/arch/arm64/mm/hugetlbpage.c
+++ b/arch/arm64/mm/hugetlbpage.c
@@ -56,25 +56,34 @@ void __init arm64_hugetlb_cma_reserve(void)
 }
 #endif /* CONFIG_CMA */
 
-#ifdef CONFIG_ARCH_ENABLE_HUGEPAGE_MIGRATION
-bool arch_hugetlb_migration_supported(struct hstate *h)
+static bool __hugetlb_valid_size(unsigned long size)
 {
-	size_t pagesize = huge_page_size(h);
-
-	switch (pagesize) {
+	switch (size) {
 #ifndef __PAGETABLE_PMD_FOLDED
 	case PUD_SIZE:
 		return pud_sect_supported();
 #endif
-	case PMD_SIZE:
 	case CONT_PMD_SIZE:
+	case PMD_SIZE:
 	case CONT_PTE_SIZE:
 		return true;
 	}
-	pr_warn("%s: unrecognized huge page size 0x%lx\n",
-			__func__, pagesize);
+
 	return false;
 }
+
+#ifdef CONFIG_ARCH_ENABLE_HUGEPAGE_MIGRATION
+bool arch_hugetlb_migration_supported(struct hstate *h)
+{
+	size_t pagesize = huge_page_size(h);
+
+	if (!__hugetlb_valid_size(pagesize)) {
+		pr_warn("%s: unrecognized huge page size 0x%lx\n",
+			__func__, pagesize);
+		return false;
+	}
+	return true;
+}
 #endif
 
 int pmd_huge(pmd_t pmd)
@@ -91,16 +100,6 @@ int pud_huge(pud_t pud)
 #endif
 }
 
-/*
- * Select all bits except the pfn
- */
-static inline pgprot_t pte_pgprot(pte_t pte)
-{
-	unsigned long pfn = pte_pfn(pte);
-
-	return __pgprot(pte_val(pfn_pte(pfn, __pgprot(0))) ^ pte_val(pte));
-}
-
 static int find_num_contig(struct mm_struct *mm, unsigned long addr,
 			   pte_t *ptep, size_t *pgsize)
 {
@@ -149,6 +148,28 @@ static inline int num_contig_ptes(unsigned long size, size_t *pgsize)
 	return contig_ptes;
 }
 
+pte_t huge_ptep_get(pte_t *ptep)
+{
+	int ncontig, i;
+	size_t pgsize;
+	pte_t orig_pte = ptep_get(ptep);
+
+	if (!pte_present(orig_pte) || !pte_cont(orig_pte))
+		return orig_pte;
+
+	ncontig = num_contig_ptes(page_size(pte_page(orig_pte)), &pgsize);
+	for (i = 0; i < ncontig; i++, ptep++) {
+		pte_t pte = ptep_get(ptep);
+
+		if (pte_dirty(pte))
+			orig_pte = pte_mkdirty(orig_pte);
+
+		if (pte_young(pte))
+			orig_pte = pte_mkyoung(orig_pte);
+	}
+	return orig_pte;
+}
+
 /*
  * Changing some bits of contiguous entries requires us to follow a
  * Break-Before-Make approach, breaking the whole contiguous set
@@ -157,15 +178,14 @@ static inline int num_contig_ptes(unsigned long size, size_t *pgsize)
  *
  * This helper performs the break step.
  */
-static pte_t get_clear_flush(struct mm_struct *mm,
+static pte_t get_clear_contig(struct mm_struct *mm,
 			     unsigned long addr,
 			     pte_t *ptep,
 			     unsigned long pgsize,
 			     unsigned long ncontig)
 {
-	pte_t orig_pte = huge_ptep_get(ptep);
-	bool valid = pte_valid(orig_pte);
-	unsigned long i, saddr = addr;
+	pte_t orig_pte = ptep_get(ptep);
+	unsigned long i;
 
 	for (i = 0; i < ncontig; i++, addr += pgsize, ptep++) {
 		pte_t pte = ptep_get_and_clear(mm, addr, ptep);
@@ -181,11 +201,19 @@ static pte_t get_clear_flush(struct mm_struct *mm,
 		if (pte_young(pte))
 			orig_pte = pte_mkyoung(orig_pte);
 	}
+	return orig_pte;
+}
 
-	if (valid) {
-		struct vm_area_struct vma = TLB_FLUSH_VMA(mm, 0);
-		flush_tlb_range(&vma, saddr, addr);
-	}
+static pte_t get_clear_contig_flush(struct mm_struct *mm,
+				    unsigned long addr,
+				    pte_t *ptep,
+				    unsigned long pgsize,
+				    unsigned long ncontig)
+{
+	pte_t orig_pte = get_clear_contig(mm, addr, ptep, pgsize, ncontig);
+	struct vm_area_struct vma = TLB_FLUSH_VMA(mm, 0);
+
+	flush_tlb_range(&vma, addr, addr + (pgsize * ncontig));
 	return orig_pte;
 }
 
@@ -213,6 +241,13 @@ static void clear_flush(struct mm_struct *mm,
 	flush_tlb_range(&vma, saddr, addr);
 }
 
+static inline struct folio *hugetlb_swap_entry_to_folio(swp_entry_t entry)
+{
+	VM_BUG_ON(!is_migration_entry(entry) && !is_hwpoison_entry(entry));
+
+	return page_folio(pfn_to_page(swp_offset_pfn(entry)));
+}
+
 void set_huge_pte_at(struct mm_struct *mm, unsigned long addr,
 			    pte_t *ptep, pte_t pte)
 {
@@ -222,11 +257,16 @@ void set_huge_pte_at(struct mm_struct *mm, unsigned long addr,
 	unsigned long pfn, dpfn;
 	pgprot_t hugeprot;
 
-	/*
-	 * Code needs to be expanded to handle huge swap and migration
-	 * entries. Needed for HUGETLB and MEMORY_FAILURE.
-	 */
-	WARN_ON(!pte_present(pte));
+	if (!pte_present(pte)) {
+		struct folio *folio;
+
+		folio = hugetlb_swap_entry_to_folio(pte_to_swp_entry(pte));
+		ncontig = num_contig_ptes(folio_size(folio), &pgsize);
+
+		for (i = 0; i < ncontig; i++, ptep++)
+			set_pte_at(mm, addr, ptep, pte);
+		return;
+	}
 
 	if (!pte_cont(pte)) {
 		set_pte_at(mm, addr, ptep, pte);
@@ -244,18 +284,6 @@ void set_huge_pte_at(struct mm_struct *mm, unsigned long addr,
 		set_pte_at(mm, addr, ptep, pfn_pte(pfn, hugeprot));
 }
 
-void set_huge_swap_pte_at(struct mm_struct *mm, unsigned long addr,
-			  pte_t *ptep, pte_t pte, unsigned long sz)
-{
-	int i, ncontig;
-	size_t pgsize;
-
-	ncontig = num_contig_ptes(sz, &pgsize);
-
-	for (i = 0; i < ncontig; i++, ptep++)
-		set_pte(ptep, pte);
-}
-
 pte_t *huge_pte_alloc(struct mm_struct *mm, struct vm_area_struct *vma,
 		      unsigned long addr, unsigned long sz)
 {
@@ -343,10 +371,33 @@ pte_t *huge_pte_offset(struct mm_struct *mm,
 	return NULL;
 }
 
+unsigned long hugetlb_mask_last_page(struct hstate *h)
+{
+	unsigned long hp_size = huge_page_size(h);
+
+	switch (hp_size) {
+#ifndef __PAGETABLE_PMD_FOLDED
+	case PUD_SIZE:
+		return PGDIR_SIZE - PUD_SIZE;
+#endif
+	case CONT_PMD_SIZE:
+		return PUD_SIZE - CONT_PMD_SIZE;
+	case PMD_SIZE:
+		return PUD_SIZE - PMD_SIZE;
+	case CONT_PTE_SIZE:
+		return PMD_SIZE - CONT_PTE_SIZE;
+	default:
+		break;
+	}
+
+	return 0UL;
+}
+
 pte_t arch_make_huge_pte(pte_t entry, unsigned int shift, vm_flags_t flags)
 {
 	size_t pagesize = 1UL << shift;
 
+	entry = pte_mkhuge(entry);
 	if (pagesize == CONT_PTE_SIZE) {
 		entry = pte_mkcont(entry);
 	} else if (pagesize == CONT_PMD_SIZE) {
@@ -375,14 +426,14 @@ pte_t huge_ptep_get_and_clear(struct mm_struct *mm,
 {
 	int ncontig;
 	size_t pgsize;
-	pte_t orig_pte = huge_ptep_get(ptep);
+	pte_t orig_pte = ptep_get(ptep);
 
 	if (!pte_cont(orig_pte))
 		return ptep_get_and_clear(mm, addr, ptep);
 
 	ncontig = find_num_contig(mm, addr, ptep, &pgsize);
 
-	return get_clear_flush(mm, addr, ptep, pgsize, ncontig);
+	return get_clear_contig(mm, addr, ptep, pgsize, ncontig);
 }
 
 /*
@@ -398,11 +449,11 @@ static int __cont_access_flags_changed(pte_t *ptep, pte_t pte, int ncontig)
 {
 	int i;
 
-	if (pte_write(pte) != pte_write(huge_ptep_get(ptep)))
+	if (pte_write(pte) != pte_write(ptep_get(ptep)))
 		return 1;
 
 	for (i = 0; i < ncontig; i++) {
-		pte_t orig_pte = huge_ptep_get(ptep + i);
+		pte_t orig_pte = ptep_get(ptep + i);
 
 		if (pte_dirty(pte) != pte_dirty(orig_pte))
 			return 1;
@@ -421,19 +472,20 @@ int huge_ptep_set_access_flags(struct vm_area_struct *vma,
 	int ncontig, i;
 	size_t pgsize = 0;
 	unsigned long pfn = pte_pfn(pte), dpfn;
+	struct mm_struct *mm = vma->vm_mm;
 	pgprot_t hugeprot;
 	pte_t orig_pte;
 
 	if (!pte_cont(pte))
 		return ptep_set_access_flags(vma, addr, ptep, pte, dirty);
 
-	ncontig = find_num_contig(vma->vm_mm, addr, ptep, &pgsize);
+	ncontig = find_num_contig(mm, addr, ptep, &pgsize);
 	dpfn = pgsize >> PAGE_SHIFT;
 
 	if (!__cont_access_flags_changed(ptep, pte, ncontig))
 		return 0;
 
-	orig_pte = get_clear_flush(vma->vm_mm, addr, ptep, pgsize, ncontig);
+	orig_pte = get_clear_contig_flush(mm, addr, ptep, pgsize, ncontig);
 
 	/* Make sure we don't lose the dirty or young state */
 	if (pte_dirty(orig_pte))
@@ -444,7 +496,7 @@ int huge_ptep_set_access_flags(struct vm_area_struct *vma,
 
 	hugeprot = pte_pgprot(pte);
 	for (i = 0; i < ncontig; i++, ptep++, addr += pgsize, pfn += dpfn)
-		set_pte_at(vma->vm_mm, addr, ptep, pfn_pte(pfn, hugeprot));
+		set_pte_at(mm, addr, ptep, pfn_pte(pfn, hugeprot));
 
 	return 1;
 }
@@ -466,7 +518,7 @@ void huge_ptep_set_wrprotect(struct mm_struct *mm,
 	ncontig = find_num_contig(mm, addr, ptep, &pgsize);
 	dpfn = pgsize >> PAGE_SHIFT;
 
-	pte = get_clear_flush(mm, addr, ptep, pgsize, ncontig);
+	pte = get_clear_contig_flush(mm, addr, ptep, pgsize, ncontig);
 	pte = pte_wrprotect(pte);
 
 	hugeprot = pte_pgprot(pte);
@@ -476,19 +528,18 @@ void huge_ptep_set_wrprotect(struct mm_struct *mm,
 		set_pte_at(mm, addr, ptep, pfn_pte(pfn, hugeprot));
 }
 
-void huge_ptep_clear_flush(struct vm_area_struct *vma,
-			   unsigned long addr, pte_t *ptep)
+pte_t huge_ptep_clear_flush(struct vm_area_struct *vma,
+			    unsigned long addr, pte_t *ptep)
 {
+	struct mm_struct *mm = vma->vm_mm;
 	size_t pgsize;
 	int ncontig;
 
-	if (!pte_cont(READ_ONCE(*ptep))) {
-		ptep_clear_flush(vma, addr, ptep);
-		return;
-	}
+	if (!pte_cont(READ_ONCE(*ptep)))
+		return ptep_clear_flush(vma, addr, ptep);
 
-	ncontig = find_num_contig(vma->vm_mm, addr, ptep, &pgsize);
-	clear_flush(vma->vm_mm, addr, ptep, pgsize, ncontig);
+	ncontig = find_num_contig(mm, addr, ptep, &pgsize);
+	return get_clear_contig_flush(mm, addr, ptep, pgsize, ncontig);
 }
 
 static int __init hugetlbpage_init(void)
@@ -506,16 +557,5 @@ arch_initcall(hugetlbpage_init);
 
 bool __init arch_hugetlb_valid_size(unsigned long size)
 {
-	switch (size) {
-#ifndef __PAGETABLE_PMD_FOLDED
-	case PUD_SIZE:
-		return pud_sect_supported();
-#endif
-	case CONT_PMD_SIZE:
-	case PMD_SIZE:
-	case CONT_PTE_SIZE:
-		return true;
-	}
-
-	return false;
+	return __hugetlb_valid_size(size);
 }
diff --git a/arch/arm64/mm/init.c b/arch/arm64/mm/init.c
index a8834434af99..4b4651ee47f2 100644
--- a/arch/arm64/mm/init.c
+++ b/arch/arm64/mm/init.c
@@ -61,10 +61,61 @@ EXPORT_SYMBOL(memstart_addr);
  * unless restricted on specific platforms (e.g. 30-bit on Raspberry Pi 4).
  * In such case, ZONE_DMA32 covers the rest of the 32-bit addressable memory,
  * otherwise it is empty.
+ *
+ * Memory reservation for crash kernel either done early or deferred
+ * depending on DMA memory zones configs (ZONE_DMA) --
+ *
+ * In absence of ZONE_DMA configs arm64_dma_phys_limit initialized
+ * here instead of max_zone_phys().  This lets early reservation of
+ * crash kernel memory which has a dependency on arm64_dma_phys_limit.
+ * Reserving memory early for crash kernel allows linear creation of block
+ * mappings (greater than page-granularity) for all the memory bank rangs.
+ * In this scheme a comparatively quicker boot is observed.
+ *
+ * If ZONE_DMA configs are defined, crash kernel memory reservation
+ * is delayed until DMA zone memory range size initialization performed in
+ * zone_sizes_init().  The defer is necessary to steer clear of DMA zone
+ * memory range to avoid overlap allocation.  So crash kernel memory boundaries
+ * are not known when mapping all bank memory ranges, which otherwise means
+ * not possible to exclude crash kernel range from creating block mappings
+ * so page-granularity mappings are created for the entire memory range.
+ * Hence a slightly slower boot is observed.
+ *
+ * Note: Page-granularity mappings are necessary for crash kernel memory
+ * range for shrinking its size via /sys/kernel/kexec_crash_size interface.
  */
-phys_addr_t arm64_dma_phys_limit __ro_after_init;
+#if IS_ENABLED(CONFIG_ZONE_DMA) || IS_ENABLED(CONFIG_ZONE_DMA32)
+phys_addr_t __ro_after_init arm64_dma_phys_limit;
+#else
+phys_addr_t __ro_after_init arm64_dma_phys_limit = PHYS_MASK + 1;
+#endif
+
+/* Current arm64 boot protocol requires 2MB alignment */
+#define CRASH_ALIGN			SZ_2M
+
+#define CRASH_ADDR_LOW_MAX		arm64_dma_phys_limit
+#define CRASH_ADDR_HIGH_MAX		(PHYS_MASK + 1)
+
+static int __init reserve_crashkernel_low(unsigned long long low_size)
+{
+	unsigned long long low_base;
+
+	low_base = memblock_phys_alloc_range(low_size, CRASH_ALIGN, 0, CRASH_ADDR_LOW_MAX);
+	if (!low_base) {
+		pr_err("cannot allocate crashkernel low memory (size:0x%llx).\n", low_size);
+		return -ENOMEM;
+	}
+
+	pr_info("crashkernel low memory reserved: 0x%08llx - 0x%08llx (%lld MB)\n",
+		low_base, low_base + low_size, low_size >> 20);
+
+	crashk_low_res.start = low_base;
+	crashk_low_res.end   = low_base + low_size - 1;
+	insert_resource(&iomem_resource, &crashk_low_res);
+
+	return 0;
+}
 
-#ifdef CONFIG_KEXEC_CORE
 /*
  * reserve_crashkernel() - reserves memory for crash kernel
  *
@@ -75,14 +126,35 @@ phys_addr_t arm64_dma_phys_limit __ro_after_init;
 static void __init reserve_crashkernel(void)
 {
 	unsigned long long crash_base, crash_size;
-	unsigned long long crash_max = arm64_dma_phys_limit;
+	unsigned long long crash_low_size = 0;
+	unsigned long long crash_max = CRASH_ADDR_LOW_MAX;
+	char *cmdline = boot_command_line;
 	int ret;
 
-	ret = parse_crashkernel(boot_command_line, memblock_phys_mem_size(),
+	if (!IS_ENABLED(CONFIG_KEXEC_CORE))
+		return;
+
+	/* crashkernel=X[@offset] */
+	ret = parse_crashkernel(cmdline, memblock_phys_mem_size(),
 				&crash_size, &crash_base);
-	/* no crashkernel= or invalid value specified */
-	if (ret || !crash_size)
+	if (ret == -ENOENT) {
+		ret = parse_crashkernel_high(cmdline, 0, &crash_size, &crash_base);
+		if (ret || !crash_size)
+			return;
+
+		/*
+		 * crashkernel=Y,low can be specified or not, but invalid value
+		 * is not allowed.
+		 */
+		ret = parse_crashkernel_low(cmdline, 0, &crash_low_size, &crash_base);
+		if (ret && (ret != -ENOENT))
+			return;
+
+		crash_max = CRASH_ADDR_HIGH_MAX;
+	} else if (ret || !crash_size) {
+		/* The specified value is invalid */
 		return;
+	}
 
 	crash_size = PAGE_ALIGN(crash_size);
 
@@ -90,8 +162,7 @@ static void __init reserve_crashkernel(void)
 	if (crash_base)
 		crash_max = crash_base + crash_size;
 
-	/* Current arm64 boot protocol requires 2MB alignment */
-	crash_base = memblock_phys_alloc_range(crash_size, SZ_2M,
+	crash_base = memblock_phys_alloc_range(crash_size, CRASH_ALIGN,
 					       crash_base, crash_max);
 	if (!crash_base) {
 		pr_warn("cannot allocate crashkernel (size:0x%llx)\n",
@@ -99,6 +170,12 @@ static void __init reserve_crashkernel(void)
 		return;
 	}
 
+	if ((crash_base >= CRASH_ADDR_LOW_MAX) &&
+	     crash_low_size && reserve_crashkernel_low(crash_low_size)) {
+		memblock_phys_free(crash_base, crash_size);
+		return;
+	}
+
 	pr_info("crashkernel reserved: 0x%016llx - 0x%016llx (%lld MB)\n",
 		crash_base, crash_base + crash_size, crash_size >> 20);
 
@@ -107,14 +184,13 @@ static void __init reserve_crashkernel(void)
 	 * map. Inform kmemleak so that it won't try to access it.
 	 */
 	kmemleak_ignore_phys(crash_base);
+	if (crashk_low_res.end)
+		kmemleak_ignore_phys(crashk_low_res.start);
+
 	crashk_res.start = crash_base;
 	crashk_res.end = crash_base + crash_size - 1;
+	insert_resource(&iomem_resource, &crashk_res);
 }
-#else
-static void __init reserve_crashkernel(void)
-{
-}
-#endif /* CONFIG_KEXEC_CORE */
 
 /*
  * Return the maximum physical address for a zone accessible by the given bits
@@ -134,7 +210,7 @@ static phys_addr_t __init max_zone_phys(unsigned int zone_bits)
 	return min(zone_mask, memblock_end_of_DRAM() - 1) + 1;
 }
 
-static void __init zone_sizes_init(unsigned long min, unsigned long max)
+static void __init zone_sizes_init(void)
 {
 	unsigned long max_zone_pfns[MAX_NR_ZONES]  = {0};
 	unsigned int __maybe_unused acpi_zone_dma_bits;
@@ -153,9 +229,7 @@ static void __init zone_sizes_init(unsigned long min, unsigned long max)
 	if (!arm64_dma_phys_limit)
 		arm64_dma_phys_limit = dma32_phys_limit;
 #endif
-	if (!arm64_dma_phys_limit)
-		arm64_dma_phys_limit = PHYS_MASK + 1;
-	max_zone_pfns[ZONE_NORMAL] = max;
+	max_zone_pfns[ZONE_NORMAL] = max_pfn;
 
 	free_area_init(max_zone_pfns);
 }
@@ -172,7 +246,7 @@ int pfn_is_map_memory(unsigned long pfn)
 }
 EXPORT_SYMBOL(pfn_is_map_memory);
 
-static phys_addr_t memory_limit = PHYS_ADDR_MAX;
+static phys_addr_t memory_limit __ro_after_init = PHYS_ADDR_MAX;
 
 /*
  * Limit the memory size that was specified via FDT.
@@ -276,8 +350,8 @@ void __init arm64_memblock_init(void)
 			"initrd not fully accessible via the linear mapping -- please check your bootloader ...\n")) {
 			phys_initrd_size = 0;
 		} else {
-			memblock_remove(base, size); /* clear MEMBLOCK_ flags */
 			memblock_add(base, size);
+			memblock_clear_nomap(base, size);
 			memblock_reserve(base, size);
 		}
 	}
@@ -286,7 +360,7 @@ void __init arm64_memblock_init(void)
 		extern u16 memstart_offset_seed;
 		u64 mmfr0 = read_cpuid(ID_AA64MMFR0_EL1);
 		int parange = cpuid_feature_extract_unsigned_field(
-					mmfr0, ID_AA64MMFR0_PARANGE_SHIFT);
+					mmfr0, ID_AA64MMFR0_EL1_PARANGE_SHIFT);
 		s64 range = linear_region_size -
 			    BIT(id_aa64mmfr0_parange_to_phys_shift(parange));
 
@@ -315,6 +389,9 @@ void __init arm64_memblock_init(void)
 
 	early_init_fdt_scan_reserved_mem();
 
+	if (!defer_reserve_crashkernel())
+		reserve_crashkernel();
+
 	high_memory = __va(memblock_end_of_DRAM() - 1) + 1;
 }
 
@@ -350,7 +427,7 @@ void __init bootmem_init(void)
 	 * done after the fixed reservations
 	 */
 	sparse_init();
-	zone_sizes_init(min, max);
+	zone_sizes_init();
 
 	/*
 	 * Reserve the CMA area after arm64_dma_phys_limit was initialised.
@@ -361,7 +438,8 @@ void __init bootmem_init(void)
 	 * request_standard_resources() depends on crashkernel's memory being
 	 * reserved, so do it here.
 	 */
-	reserve_crashkernel();
+	if (defer_reserve_crashkernel())
+		reserve_crashkernel();
 
 	memblock_dump_all();
 }
@@ -373,11 +451,7 @@ void __init bootmem_init(void)
  */
 void __init mem_init(void)
 {
-	if (swiotlb_force == SWIOTLB_FORCE ||
-	    max_pfn > PFN_DOWN(arm64_dma_phys_limit))
-		swiotlb_init(1);
-	else if (!xen_swiotlb_detect())
-		swiotlb_force = SWIOTLB_NO_FORCE;
+	swiotlb_init(max_pfn > PFN_DOWN(arm64_dma_phys_limit), SWIOTLB_VERBOSE);
 
 	/* this will put all unused low memory onto the freelists */
 	memblock_free_all();
diff --git a/arch/arm64/mm/ioremap.c b/arch/arm64/mm/ioremap.c
index b7c81dacabf0..c5af103d4ad4 100644
--- a/arch/arm64/mm/ioremap.c
+++ b/arch/arm64/mm/ioremap.c
@@ -1,97 +1,23 @@
 // SPDX-License-Identifier: GPL-2.0-only
-/*
- * Based on arch/arm/mm/ioremap.c
- *
- * (C) Copyright 1995 1996 Linus Torvalds
- * Hacked for ARM by Phil Blundell <philb@gnu.org>
- * Hacked to allow all architectures to build, and various cleanups
- * by Russell King
- * Copyright (C) 2012 ARM Ltd.
- */
 
-#include <linux/export.h>
 #include <linux/mm.h>
-#include <linux/vmalloc.h>
 #include <linux/io.h>
 
-#include <asm/fixmap.h>
-#include <asm/tlbflush.h>
-
-static void __iomem *__ioremap_caller(phys_addr_t phys_addr, size_t size,
-				      pgprot_t prot, void *caller)
+bool ioremap_allowed(phys_addr_t phys_addr, size_t size, unsigned long prot)
 {
-	unsigned long last_addr;
-	unsigned long offset = phys_addr & ~PAGE_MASK;
-	int err;
-	unsigned long addr;
-	struct vm_struct *area;
+	unsigned long last_addr = phys_addr + size - 1;
 
-	/*
-	 * Page align the mapping address and size, taking account of any
-	 * offset.
-	 */
-	phys_addr &= PAGE_MASK;
-	size = PAGE_ALIGN(size + offset);
+	/* Don't allow outside PHYS_MASK */
+	if (last_addr & ~PHYS_MASK)
+		return false;
 
-	/*
-	 * Don't allow wraparound, zero size or outside PHYS_MASK.
-	 */
-	last_addr = phys_addr + size - 1;
-	if (!size || last_addr < phys_addr || (last_addr & ~PHYS_MASK))
-		return NULL;
-
-	/*
-	 * Don't allow RAM to be mapped.
-	 */
+	/* Don't allow RAM to be mapped. */
 	if (WARN_ON(pfn_is_map_memory(__phys_to_pfn(phys_addr))))
-		return NULL;
-
-	area = get_vm_area_caller(size, VM_IOREMAP, caller);
-	if (!area)
-		return NULL;
-	addr = (unsigned long)area->addr;
-	area->phys_addr = phys_addr;
-
-	err = ioremap_page_range(addr, addr + size, phys_addr, prot);
-	if (err) {
-		vunmap((void *)addr);
-		return NULL;
-	}
+		return false;
 
-	return (void __iomem *)(offset + addr);
+	return true;
 }
 
-void __iomem *__ioremap(phys_addr_t phys_addr, size_t size, pgprot_t prot)
-{
-	return __ioremap_caller(phys_addr, size, prot,
-				__builtin_return_address(0));
-}
-EXPORT_SYMBOL(__ioremap);
-
-void iounmap(volatile void __iomem *io_addr)
-{
-	unsigned long addr = (unsigned long)io_addr & PAGE_MASK;
-
-	/*
-	 * We could get an address outside vmalloc range in case
-	 * of ioremap_cache() reusing a RAM mapping.
-	 */
-	if (is_vmalloc_addr((void *)addr))
-		vunmap((void *)addr);
-}
-EXPORT_SYMBOL(iounmap);
-
-void __iomem *ioremap_cache(phys_addr_t phys_addr, size_t size)
-{
-	/* For normal memory we already have a cacheable mapping. */
-	if (pfn_is_map_memory(__phys_to_pfn(phys_addr)))
-		return (void __iomem *)__phys_to_virt(phys_addr);
-
-	return __ioremap_caller(phys_addr, size, __pgprot(PROT_NORMAL),
-				__builtin_return_address(0));
-}
-EXPORT_SYMBOL(ioremap_cache);
-
 /*
  * Must be called after early_fixmap_init
  */
@@ -99,3 +25,11 @@ void __init early_ioremap_init(void)
 {
 	early_ioremap_setup();
 }
+
+bool arch_memremap_can_ram_remap(resource_size_t offset, size_t size,
+				 unsigned long flags)
+{
+	unsigned long pfn = PHYS_PFN(offset);
+
+	return pfn_is_map_memory(pfn);
+}
diff --git a/arch/arm64/mm/kasan_init.c b/arch/arm64/mm/kasan_init.c
index c12cd700598f..e969e68de005 100644
--- a/arch/arm64/mm/kasan_init.c
+++ b/arch/arm64/mm/kasan_init.c
@@ -236,7 +236,7 @@ static void __init kasan_init_shadow(void)
 	 */
 	memcpy(tmp_pg_dir, swapper_pg_dir, sizeof(tmp_pg_dir));
 	dsb(ishst);
-	cpu_replace_ttbr1(lm_alias(tmp_pg_dir));
+	cpu_replace_ttbr1(lm_alias(tmp_pg_dir), idmap_pg_dir);
 
 	clear_pgds(KASAN_SHADOW_START, KASAN_SHADOW_END);
 
@@ -280,7 +280,7 @@ static void __init kasan_init_shadow(void)
 				PAGE_KERNEL_RO));
 
 	memset(kasan_early_shadow_page, KASAN_SHADOW_INIT, PAGE_SIZE);
-	cpu_replace_ttbr1(lm_alias(swapper_pg_dir));
+	cpu_replace_ttbr1(lm_alias(swapper_pg_dir), idmap_pg_dir);
 }
 
 static void __init kasan_init_depth(void)
diff --git a/arch/arm64/mm/mmap.c b/arch/arm64/mm/mmap.c
index a38f54cd638c..8f5b7ce857ed 100644
--- a/arch/arm64/mm/mmap.c
+++ b/arch/arm64/mm/mmap.c
@@ -7,10 +7,33 @@
 
 #include <linux/io.h>
 #include <linux/memblock.h>
+#include <linux/mm.h>
 #include <linux/types.h>
 
+#include <asm/cpufeature.h>
 #include <asm/page.h>
 
+static pgprot_t protection_map[16] __ro_after_init = {
+	[VM_NONE]					= PAGE_NONE,
+	[VM_READ]					= PAGE_READONLY,
+	[VM_WRITE]					= PAGE_READONLY,
+	[VM_WRITE | VM_READ]				= PAGE_READONLY,
+	/* PAGE_EXECONLY if Enhanced PAN */
+	[VM_EXEC]					= PAGE_READONLY_EXEC,
+	[VM_EXEC | VM_READ]				= PAGE_READONLY_EXEC,
+	[VM_EXEC | VM_WRITE]				= PAGE_READONLY_EXEC,
+	[VM_EXEC | VM_WRITE | VM_READ]			= PAGE_READONLY_EXEC,
+	[VM_SHARED]					= PAGE_NONE,
+	[VM_SHARED | VM_READ]				= PAGE_READONLY,
+	[VM_SHARED | VM_WRITE]				= PAGE_SHARED,
+	[VM_SHARED | VM_WRITE | VM_READ]		= PAGE_SHARED,
+	/* PAGE_EXECONLY if Enhanced PAN */
+	[VM_SHARED | VM_EXEC]				= PAGE_READONLY_EXEC,
+	[VM_SHARED | VM_EXEC | VM_READ]			= PAGE_READONLY_EXEC,
+	[VM_SHARED | VM_EXEC | VM_WRITE]		= PAGE_SHARED_EXEC,
+	[VM_SHARED | VM_EXEC | VM_WRITE | VM_READ]	= PAGE_SHARED_EXEC
+};
+
 /*
  * You really shouldn't be using read() or write() on /dev/mem.  This might go
  * away in the future.
@@ -38,3 +61,43 @@ int valid_mmap_phys_addr_range(unsigned long pfn, size_t size)
 {
 	return !(((pfn << PAGE_SHIFT) + size) & ~PHYS_MASK);
 }
+
+static int __init adjust_protection_map(void)
+{
+	/*
+	 * With Enhanced PAN we can honour the execute-only permissions as
+	 * there is no PAN override with such mappings.
+	 */
+	if (cpus_have_const_cap(ARM64_HAS_EPAN)) {
+		protection_map[VM_EXEC] = PAGE_EXECONLY;
+		protection_map[VM_EXEC | VM_SHARED] = PAGE_EXECONLY;
+	}
+
+	return 0;
+}
+arch_initcall(adjust_protection_map);
+
+pgprot_t vm_get_page_prot(unsigned long vm_flags)
+{
+	pteval_t prot = pgprot_val(protection_map[vm_flags &
+				   (VM_READ|VM_WRITE|VM_EXEC|VM_SHARED)]);
+
+	if (vm_flags & VM_ARM64_BTI)
+		prot |= PTE_GP;
+
+	/*
+	 * There are two conditions required for returning a Normal Tagged
+	 * memory type: (1) the user requested it via PROT_MTE passed to
+	 * mmap() or mprotect() and (2) the corresponding vma supports MTE. We
+	 * register (1) as VM_MTE in the vma->vm_flags and (2) as
+	 * VM_MTE_ALLOWED. Note that the latter can only be set during the
+	 * mmap() call since mprotect() does not accept MAP_* flags.
+	 * Checking for VM_MTE only is sufficient since arch_validate_flags()
+	 * does not permit (VM_MTE & !VM_MTE_ALLOWED).
+	 */
+	if (vm_flags & VM_MTE)
+		prot |= PTE_ATTRINDX(MT_NORMAL_TAGGED);
+
+	return __pgprot(prot);
+}
+EXPORT_SYMBOL(vm_get_page_prot);
diff --git a/arch/arm64/mm/mmu.c b/arch/arm64/mm/mmu.c
index acfae9b41cc8..9a7c38965154 100644
--- a/arch/arm64/mm/mmu.c
+++ b/arch/arm64/mm/mmu.c
@@ -17,6 +17,7 @@
 #include <linux/mman.h>
 #include <linux/nodemask.h>
 #include <linux/memblock.h>
+#include <linux/memremap.h>
 #include <linux/memory.h>
 #include <linux/fs.h>
 #include <linux/io.h>
@@ -42,15 +43,27 @@
 #define NO_CONT_MAPPINGS	BIT(1)
 #define NO_EXEC_MAPPINGS	BIT(2)	/* assumes FEAT_HPDS is not used */
 
-u64 idmap_t0sz = TCR_T0SZ(VA_BITS_MIN);
-u64 idmap_ptrs_per_pgd = PTRS_PER_PGD;
+int idmap_t0sz __ro_after_init;
 
-u64 __section(".mmuoff.data.write") vabits_actual;
+#if VA_BITS > 48
+u64 vabits_actual __ro_after_init = VA_BITS_MIN;
 EXPORT_SYMBOL(vabits_actual);
+#endif
+
+u64 kimage_vaddr __ro_after_init = (u64)&_text;
+EXPORT_SYMBOL(kimage_vaddr);
 
 u64 kimage_voffset __ro_after_init;
 EXPORT_SYMBOL(kimage_voffset);
 
+u32 __boot_cpu_mode[] = { BOOT_CPU_MODE_EL2, BOOT_CPU_MODE_EL1 };
+
+/*
+ * The booting CPU updates the failed status @__early_cpu_boot_status,
+ * with MMU turned off.
+ */
+long __section(".mmuoff.data.write") __early_cpu_boot_status;
+
 /*
  * Empty_zero_page is a special page that is used for zero-initialized data
  * and COW.
@@ -63,6 +76,7 @@ static pmd_t bm_pmd[PTRS_PER_PMD] __page_aligned_bss __maybe_unused;
 static pud_t bm_pud[PTRS_PER_PUD] __page_aligned_bss __maybe_unused;
 
 static DEFINE_SPINLOCK(swapper_pgdir_lock);
+static DEFINE_MUTEX(fixmap_lock);
 
 void set_swapper_pgd(pgd_t *pgdp, pgd_t pgd)
 {
@@ -294,18 +308,6 @@ static void alloc_init_cont_pmd(pud_t *pudp, unsigned long addr,
 	} while (addr = next, addr != end);
 }
 
-static inline bool use_1G_block(unsigned long addr, unsigned long next,
-			unsigned long phys)
-{
-	if (PAGE_SHIFT != 12)
-		return false;
-
-	if (((addr | next | phys) & ~PUD_MASK) != 0)
-		return false;
-
-	return true;
-}
-
 static void alloc_init_pud(pgd_t *pgdp, unsigned long addr, unsigned long end,
 			   phys_addr_t phys, pgprot_t prot,
 			   phys_addr_t (*pgtable_alloc)(int),
@@ -338,7 +340,8 @@ static void alloc_init_pud(pgd_t *pgdp, unsigned long addr, unsigned long end,
 		/*
 		 * For 4K granule only, attempt to put down a 1GB block
 		 */
-		if (use_1G_block(addr, next, phys) &&
+		if (pud_sect_supported() &&
+		   ((addr | next | phys) & ~PUD_MASK) == 0 &&
 		    (flags & NO_BLOCK_MAPPINGS) == 0) {
 			pud_set_huge(pudp, phys, prot);
 
@@ -361,11 +364,11 @@ static void alloc_init_pud(pgd_t *pgdp, unsigned long addr, unsigned long end,
 	pud_clear_fixmap();
 }
 
-static void __create_pgd_mapping(pgd_t *pgdir, phys_addr_t phys,
-				 unsigned long virt, phys_addr_t size,
-				 pgprot_t prot,
-				 phys_addr_t (*pgtable_alloc)(int),
-				 int flags)
+static void __create_pgd_mapping_locked(pgd_t *pgdir, phys_addr_t phys,
+					unsigned long virt, phys_addr_t size,
+					pgprot_t prot,
+					phys_addr_t (*pgtable_alloc)(int),
+					int flags)
 {
 	unsigned long addr, end, next;
 	pgd_t *pgdp = pgd_offset_pgd(pgdir, virt);
@@ -389,6 +392,25 @@ static void __create_pgd_mapping(pgd_t *pgdir, phys_addr_t phys,
 	} while (pgdp++, addr = next, addr != end);
 }
 
+static void __create_pgd_mapping(pgd_t *pgdir, phys_addr_t phys,
+				 unsigned long virt, phys_addr_t size,
+				 pgprot_t prot,
+				 phys_addr_t (*pgtable_alloc)(int),
+				 int flags)
+{
+	mutex_lock(&fixmap_lock);
+	__create_pgd_mapping_locked(pgdir, phys, virt, size, prot,
+				    pgtable_alloc, flags);
+	mutex_unlock(&fixmap_lock);
+}
+
+#ifdef CONFIG_UNMAP_KERNEL_AT_EL0
+extern __alias(__create_pgd_mapping_locked)
+void create_kpti_ng_temp_pgd(pgd_t *pgdir, phys_addr_t phys, unsigned long virt,
+			     phys_addr_t size, pgprot_t prot,
+			     phys_addr_t (*pgtable_alloc)(int), int flags);
+#endif
+
 static phys_addr_t __pgd_pgtable_alloc(int shift)
 {
 	void *ptr = (void *)__get_free_page(GFP_PGTABLE_KERNEL);
@@ -517,7 +539,7 @@ static void __init map_mem(pgd_t *pgdp)
 	 */
 	BUILD_BUG_ON(pgd_index(direct_map_end - 1) == pgd_index(direct_map_end));
 
-	if (can_set_direct_map() || crash_mem_map || IS_ENABLED(CONFIG_KFENCE))
+	if (can_set_direct_map())
 		flags |= NO_BLOCK_MAPPINGS | NO_CONT_MAPPINGS;
 
 	/*
@@ -528,6 +550,16 @@ static void __init map_mem(pgd_t *pgdp)
 	 */
 	memblock_mark_nomap(kernel_start, kernel_end - kernel_start);
 
+#ifdef CONFIG_KEXEC_CORE
+	if (crash_mem_map) {
+		if (defer_reserve_crashkernel())
+			flags |= NO_BLOCK_MAPPINGS | NO_CONT_MAPPINGS;
+		else if (crashk_res.end)
+			memblock_mark_nomap(crashk_res.start,
+			    resource_size(&crashk_res));
+	}
+#endif
+
 	/* map all the memory banks */
 	for_each_mem_range(i, &start, &end) {
 		if (start >= end)
@@ -554,6 +586,24 @@ static void __init map_mem(pgd_t *pgdp)
 	__map_memblock(pgdp, kernel_start, kernel_end,
 		       PAGE_KERNEL, NO_CONT_MAPPINGS);
 	memblock_clear_nomap(kernel_start, kernel_end - kernel_start);
+
+	/*
+	 * Use page-level mappings here so that we can shrink the region
+	 * in page granularity and put back unused memory to buddy system
+	 * through /sys/kernel/kexec_crash_size interface.
+	 */
+#ifdef CONFIG_KEXEC_CORE
+	if (crash_mem_map && !defer_reserve_crashkernel()) {
+		if (crashk_res.end) {
+			__map_memblock(pgdp, crashk_res.start,
+				       crashk_res.end + 1,
+				       PAGE_KERNEL,
+				       NO_BLOCK_MAPPINGS | NO_CONT_MAPPINGS);
+			memblock_clear_nomap(crashk_res.start,
+					     resource_size(&crashk_res));
+		}
+	}
+#endif
 }
 
 void mark_rodata_ro(void)
@@ -596,27 +646,11 @@ static void __init map_kernel_segment(pgd_t *pgdp, void *va_start, void *va_end,
 	vm_area_add_early(vma);
 }
 
-static int __init parse_rodata(char *arg)
-{
-	int ret = strtobool(arg, &rodata_enabled);
-	if (!ret) {
-		rodata_full = false;
-		return 0;
-	}
-
-	/* permit 'full' in addition to boolean options */
-	if (strcmp(arg, "full"))
-		return -EINVAL;
-
-	rodata_enabled = true;
-	rodata_full = true;
-	return 0;
-}
-early_param("rodata", parse_rodata);
-
 #ifdef CONFIG_UNMAP_KERNEL_AT_EL0
 static int __init map_entry_trampoline(void)
 {
+	int i;
+
 	pgprot_t prot = rodata_enabled ? PAGE_KERNEL_ROX : PAGE_KERNEL_EXEC;
 	phys_addr_t pa_start = __pa_symbol(__entry_tramp_text_start);
 
@@ -625,18 +659,18 @@ static int __init map_entry_trampoline(void)
 
 	/* Map only the text into the trampoline page table */
 	memset(tramp_pg_dir, 0, PGD_SIZE);
-	__create_pgd_mapping(tramp_pg_dir, pa_start, TRAMP_VALIAS, PAGE_SIZE,
-			     prot, __pgd_pgtable_alloc, 0);
+	__create_pgd_mapping(tramp_pg_dir, pa_start, TRAMP_VALIAS,
+			     entry_tramp_text_size(), prot,
+			     __pgd_pgtable_alloc, NO_BLOCK_MAPPINGS);
 
 	/* Map both the text and data into the kernel page table */
-	__set_fixmap(FIX_ENTRY_TRAMP_TEXT, pa_start, prot);
-	if (IS_ENABLED(CONFIG_RANDOMIZE_BASE)) {
-		extern char __entry_tramp_data_start[];
+	for (i = 0; i < DIV_ROUND_UP(entry_tramp_text_size(), PAGE_SIZE); i++)
+		__set_fixmap(FIX_ENTRY_TRAMP_TEXT1 - i,
+			     pa_start + i * PAGE_SIZE, prot);
 
-		__set_fixmap(FIX_ENTRY_TRAMP_DATA,
-			     __pa_symbol(__entry_tramp_data_start),
-			     PAGE_KERNEL_RO);
-	}
+	if (IS_ENABLED(CONFIG_RELOCATABLE))
+		__set_fixmap(FIX_ENTRY_TRAMP_TEXT1 - i,
+			     pa_start + i * PAGE_SIZE, PAGE_KERNEL_RO);
 
 	return 0;
 }
@@ -656,7 +690,7 @@ static bool arm64_early_this_cpu_has_bti(void)
 
 	pfr1 = __read_sysreg_by_encoding(SYS_ID_AA64PFR1_EL1);
 	return cpuid_feature_extract_unsigned_field(pfr1,
-						    ID_AA64PFR1_BT_SHIFT);
+						    ID_AA64PFR1_EL1_BT_SHIFT);
 }
 
 /*
@@ -727,22 +761,57 @@ static void __init map_kernel(pgd_t *pgdp)
 	kasan_copy_shadow(pgdp);
 }
 
+static void __init create_idmap(void)
+{
+	u64 start = __pa_symbol(__idmap_text_start);
+	u64 size = __pa_symbol(__idmap_text_end) - start;
+	pgd_t *pgd = idmap_pg_dir;
+	u64 pgd_phys;
+
+	/* check if we need an additional level of translation */
+	if (VA_BITS < 48 && idmap_t0sz < (64 - VA_BITS_MIN)) {
+		pgd_phys = early_pgtable_alloc(PAGE_SHIFT);
+		set_pgd(&idmap_pg_dir[start >> VA_BITS],
+			__pgd(pgd_phys | P4D_TYPE_TABLE));
+		pgd = __va(pgd_phys);
+	}
+	__create_pgd_mapping(pgd, start, start, size, PAGE_KERNEL_ROX,
+			     early_pgtable_alloc, 0);
+
+	if (IS_ENABLED(CONFIG_UNMAP_KERNEL_AT_EL0)) {
+		extern u32 __idmap_kpti_flag;
+		u64 pa = __pa_symbol(&__idmap_kpti_flag);
+
+		/*
+		 * The KPTI G-to-nG conversion code needs a read-write mapping
+		 * of its synchronization flag in the ID map.
+		 */
+		__create_pgd_mapping(pgd, pa, pa, sizeof(u32), PAGE_KERNEL,
+				     early_pgtable_alloc, 0);
+	}
+}
+
 void __init paging_init(void)
 {
 	pgd_t *pgdp = pgd_set_fixmap(__pa_symbol(swapper_pg_dir));
+	extern pgd_t init_idmap_pg_dir[];
+
+	idmap_t0sz = 63UL - __fls(__pa_symbol(_end) | GENMASK(VA_BITS_MIN - 1, 0));
 
 	map_kernel(pgdp);
 	map_mem(pgdp);
 
 	pgd_clear_fixmap();
 
-	cpu_replace_ttbr1(lm_alias(swapper_pg_dir));
+	cpu_replace_ttbr1(lm_alias(swapper_pg_dir), init_idmap_pg_dir);
 	init_mm.pgd = swapper_pg_dir;
 
 	memblock_phys_free(__pa_symbol(init_pg_dir),
 			   __pa_symbol(init_pg_end) - __pa_symbol(init_pg_dir));
 
 	memblock_allow_resize();
+
+	create_idmap();
 }
 
 /*
@@ -1115,14 +1184,6 @@ static void free_empty_tables(unsigned long addr, unsigned long end,
 }
 #endif
 
-#if !ARM64_KERNEL_USES_PMD_MAPS
-int __meminit vmemmap_populate(unsigned long start, unsigned long end, int node,
-		struct vmem_altmap *altmap)
-{
-	WARN_ON((start < VMEMMAP_START) || (end > VMEMMAP_END));
-	return vmemmap_populate_basepages(start, end, node, altmap);
-}
-#else	/* !ARM64_KERNEL_USES_PMD_MAPS */
 int __meminit vmemmap_populate(unsigned long start, unsigned long end, int node,
 		struct vmem_altmap *altmap)
 {
@@ -1134,6 +1195,10 @@ int __meminit vmemmap_populate(unsigned long start, unsigned long end, int node,
 	pmd_t *pmdp;
 
 	WARN_ON((start < VMEMMAP_START) || (end > VMEMMAP_END));
+
+	if (!ARM64_KERNEL_USES_PMD_MAPS)
+		return vmemmap_populate_basepages(start, end, node, altmap);
+
 	do {
 		next = pmd_addr_end(addr, end);
 
@@ -1167,7 +1232,6 @@ int __meminit vmemmap_populate(unsigned long start, unsigned long end, int node,
 
 	return 0;
 }
-#endif	/* !ARM64_KERNEL_USES_PMD_MAPS */
 
 #ifdef CONFIG_MEMORY_HOTPLUG
 void vmemmap_free(unsigned long start, unsigned long end,
@@ -1482,11 +1546,7 @@ int arch_add_memory(int nid, u64 start, u64 size,
 
 	VM_BUG_ON(!mhp_range_allowed(start, size, true));
 
-	/*
-	 * KFENCE requires linear map to be mapped at page granularity, so that
-	 * it is possible to protect/unprotect single pages in the KFENCE pool.
-	 */
-	if (can_set_direct_map() || IS_ENABLED(CONFIG_KFENCE))
+	if (can_set_direct_map())
 		flags |= NO_BLOCK_MAPPINGS | NO_CONT_MAPPINGS;
 
 	__create_pgd_mapping(swapper_pg_dir, start, __phys_to_virt(start),
diff --git a/arch/arm64/mm/mteswap.c b/arch/arm64/mm/mteswap.c
index 7c4ef56265ee..bed803d8e158 100644
--- a/arch/arm64/mm/mteswap.c
+++ b/arch/arm64/mm/mteswap.c
@@ -12,7 +12,7 @@ static DEFINE_XARRAY(mte_pages);
 void *mte_allocate_tag_storage(void)
 {
 	/* tags granule is 16 bytes, 2 tags stored per byte */
-	return kmalloc(PAGE_SIZE / 16 / 2, GFP_KERNEL);
+	return kmalloc(MTE_PAGE_TAG_STORAGE, GFP_KERNEL);
 }
 
 void mte_free_tag_storage(char *storage)
@@ -53,16 +53,12 @@ bool mte_restore_tags(swp_entry_t entry, struct page *page)
 	if (!tags)
 		return false;
 
-	page_kasan_tag_reset(page);
 	/*
-	 * We need smp_wmb() in between setting the flags and clearing the
-	 * tags because if another thread reads page->flags and builds a
-	 * tagged address out of it, there is an actual dependency to the
-	 * memory access, but on the current thread we do not guarantee that
-	 * the new page->flags are visible before the tags were updated.
+	 * Test PG_mte_tagged again in case it was racing with another
+	 * set_pte_at().
 	 */
-	smp_wmb();
-	mte_restore_page_tags(page_address(page), tags);
+	if (!test_and_set_bit(PG_mte_tagged, &page->flags))
+		mte_restore_page_tags(page_address(page), tags);
 
 	return true;
 }
diff --git a/arch/arm64/mm/pageattr.c b/arch/arm64/mm/pageattr.c
index a3bacd79507a..5922178d7a06 100644
--- a/arch/arm64/mm/pageattr.c
+++ b/arch/arm64/mm/pageattr.c
@@ -21,7 +21,13 @@ bool rodata_full __ro_after_init = IS_ENABLED(CONFIG_RODATA_FULL_DEFAULT_ENABLED
 
 bool can_set_direct_map(void)
 {
-	return rodata_full || debug_pagealloc_enabled();
+	/*
+	 * rodata_full, DEBUG_PAGEALLOC and KFENCE require linear map to be
+	 * mapped at page granularity, so that it is possible to
+	 * protect/unprotect single pages.
+	 */
+	return (rodata_enabled && rodata_full) || debug_pagealloc_enabled() ||
+		IS_ENABLED(CONFIG_KFENCE);
 }
 
 static int change_page_range(pte_t *ptep, unsigned long addr, void *data)
@@ -85,7 +91,7 @@ static int change_memory_common(unsigned long addr, int numpages,
 	 */
 	area = find_vm_area((void *)addr);
 	if (!area ||
-	    end > (unsigned long)area->addr + area->size ||
+	    end > (unsigned long)kasan_reset_tag(area->addr) + area->size ||
 	    !(area->flags & VM_ALLOC))
 		return -EINVAL;
 
@@ -96,7 +102,8 @@ static int change_memory_common(unsigned long addr, int numpages,
 	 * If we are manipulating read-only permissions, apply the same
 	 * change to the linear mapping of the pages that back this VM area.
 	 */
-	if (rodata_full && (pgprot_val(set_mask) == PTE_RDONLY ||
+	if (rodata_enabled &&
+	    rodata_full && (pgprot_val(set_mask) == PTE_RDONLY ||
 			    pgprot_val(clear_mask) == PTE_RDONLY)) {
 		for (i = 0; i < area->nr_pages; i++) {
 			__change_memory_common((u64)page_address(area->pages[i]),
diff --git a/arch/arm64/mm/proc.S b/arch/arm64/mm/proc.S
index d35c90d2e47a..b9ecbbae1e1a 100644
--- a/arch/arm64/mm/proc.S
+++ b/arch/arm64/mm/proc.S
@@ -10,10 +10,12 @@
 #include <linux/init.h>
 #include <linux/linkage.h>
 #include <linux/pgtable.h>
+#include <linux/cfi_types.h>
 #include <asm/assembler.h>
 #include <asm/asm-offsets.h>
 #include <asm/asm_pointer_auth.h>
 #include <asm/hwcap.h>
+#include <asm/kernel-pgtable.h>
 #include <asm/pgtable-hwdef.h>
 #include <asm/cpufeature.h>
 #include <asm/alternative.h>
@@ -46,18 +48,20 @@
 #endif
 
 #ifdef CONFIG_KASAN_HW_TAGS
-#define TCR_MTE_FLAGS SYS_TCR_EL1_TCMA1 | TCR_TBI1 | TCR_TBID1
-#else
+#define TCR_MTE_FLAGS TCR_TCMA1 | TCR_TBI1 | TCR_TBID1
+#elif defined(CONFIG_ARM64_MTE)
 /*
  * The mte_zero_clear_page_tags() implementation uses DC GZVA, which relies on
  * TBI being enabled at EL1.
  */
 #define TCR_MTE_FLAGS TCR_TBI1 | TCR_TBID1
+#else
+#define TCR_MTE_FLAGS 0
 #endif
 
 /*
  * Default MAIR_EL1. MT_NORMAL_TAGGED is initially mapped as Normal memory and
- * changed during __cpu_setup to Normal Tagged if the system supports MTE.
+ * changed during mte_cpu_setup to Normal Tagged if the system supports MTE.
  */
 #define MAIR_EL1_SET							\
 	(MAIR_ATTRIDX(MAIR_ATTR_DEVICE_nGnRnE, MT_DEVICE_nGnRnE) |	\
@@ -184,7 +188,7 @@ SYM_FUNC_END(cpu_do_resume)
  * This is the low-level counterpart to cpu_replace_ttbr1, and should not be
  * called by anything else. It can only be executed from a TTBR0 mapping.
  */
-SYM_FUNC_START(idmap_cpu_replace_ttbr1)
+SYM_TYPED_FUNC_START(idmap_cpu_replace_ttbr1)
 	save_and_disable_daif flags=x2
 
 	__idmap_cpu_set_reserved_ttbr1 x1, x3
@@ -200,34 +204,64 @@ SYM_FUNC_END(idmap_cpu_replace_ttbr1)
 	.popsection
 
 #ifdef CONFIG_UNMAP_KERNEL_AT_EL0
+
+#define KPTI_NG_PTE_FLAGS	(PTE_ATTRINDX(MT_NORMAL) | SWAPPER_PTE_FLAGS)
+
 	.pushsection ".idmap.text", "awx"
 
-	.macro	__idmap_kpti_get_pgtable_ent, type
-	dc	cvac, cur_\()\type\()p		// Ensure any existing dirty
-	dmb	sy				// lines are written back before
-	ldr	\type, [cur_\()\type\()p]	// loading the entry
-	tbz	\type, #0, skip_\()\type	// Skip invalid and
-	tbnz	\type, #11, skip_\()\type	// non-global entries
+	.macro	kpti_mk_tbl_ng, type, num_entries
+	add	end_\type\()p, cur_\type\()p, #\num_entries * 8
+.Ldo_\type:
+	ldr	\type, [cur_\type\()p]		// Load the entry
+	tbz	\type, #0, .Lnext_\type		// Skip invalid and
+	tbnz	\type, #11, .Lnext_\type	// non-global entries
+	orr	\type, \type, #PTE_NG		// Same bit for blocks and pages
+	str	\type, [cur_\type\()p]		// Update the entry
+	.ifnc	\type, pte
+	tbnz	\type, #1, .Lderef_\type
+	.endif
+.Lnext_\type:
+	add	cur_\type\()p, cur_\type\()p, #8
+	cmp	cur_\type\()p, end_\type\()p
+	b.ne	.Ldo_\type
 	.endm
 
-	.macro __idmap_kpti_put_pgtable_ent_ng, type
-	orr	\type, \type, #PTE_NG		// Same bit for blocks and pages
-	str	\type, [cur_\()\type\()p]	// Update the entry and ensure
-	dmb	sy				// that it is visible to all
-	dc	civac, cur_\()\type\()p		// CPUs.
+	/*
+	 * Dereference the current table entry and map it into the temporary
+	 * fixmap slot associated with the current level.
+	 */
+	.macro	kpti_map_pgtbl, type, level
+	str	xzr, [temp_pte, #8 * (\level + 1)]	// break before make
+	dsb	nshst
+	add	pte, temp_pte, #PAGE_SIZE * (\level + 1)
+	lsr	pte, pte, #12
+	tlbi	vaae1, pte
+	dsb	nsh
+	isb
+
+	phys_to_pte pte, cur_\type\()p
+	add	cur_\type\()p, temp_pte, #PAGE_SIZE * (\level + 1)
+	orr	pte, pte, pte_flags
+	str	pte, [temp_pte, #8 * (\level + 1)]
+	dsb	nshst
 	.endm
 
 /*
- * void __kpti_install_ng_mappings(int cpu, int num_cpus, phys_addr_t swapper)
+ * void __kpti_install_ng_mappings(int cpu, int num_secondaries, phys_addr_t temp_pgd,
+ *				   unsigned long temp_pte_va)
  *
  * Called exactly once from stop_machine context by each CPU found during boot.
  */
-__idmap_kpti_flag:
-	.long	1
-SYM_FUNC_START(idmap_kpti_install_ng_mappings)
+	.pushsection	".data", "aw", %progbits
+SYM_DATA(__idmap_kpti_flag, .long 1)
+	.popsection
+
+SYM_TYPED_FUNC_START(idmap_kpti_install_ng_mappings)
 	cpu		.req	w0
+	temp_pte	.req	x0
 	num_cpus	.req	w1
-	swapper_pa	.req	x2
+	pte_flags	.req	x1
+	temp_pgd_phys	.req	x2
 	swapper_ttb	.req	x3
 	flag_ptr	.req	x4
 	cur_pgdp	.req	x5
@@ -235,17 +269,16 @@ SYM_FUNC_START(idmap_kpti_install_ng_mappings)
 	pgd		.req	x7
 	cur_pudp	.req	x8
 	end_pudp	.req	x9
-	pud		.req	x10
 	cur_pmdp	.req	x11
 	end_pmdp	.req	x12
-	pmd		.req	x13
 	cur_ptep	.req	x14
 	end_ptep	.req	x15
 	pte		.req	x16
+	valid		.req	x17
 
+	mov	x5, x3				// preserve temp_pte arg
 	mrs	swapper_ttb, ttbr1_el1
-	restore_ttbr1	swapper_ttb
-	adr	flag_ptr, __idmap_kpti_flag
+	adr_l	flag_ptr, __idmap_kpti_flag
 
 	cbnz	cpu, __idmap_kpti_secondary
 
@@ -256,98 +289,71 @@ SYM_FUNC_START(idmap_kpti_install_ng_mappings)
 	eor	w17, w17, num_cpus
 	cbnz	w17, 1b
 
-	/* We need to walk swapper, so turn off the MMU. */
-	pre_disable_mmu_workaround
-	mrs	x17, sctlr_el1
-	bic	x17, x17, #SCTLR_ELx_M
-	msr	sctlr_el1, x17
+	/* Switch to the temporary page tables on this CPU only */
+	__idmap_cpu_set_reserved_ttbr1 x8, x9
+	offset_ttbr1 temp_pgd_phys, x8
+	msr	ttbr1_el1, temp_pgd_phys
 	isb
 
+	mov	temp_pte, x5
+	mov	pte_flags, #KPTI_NG_PTE_FLAGS
+
 	/* Everybody is enjoying the idmap, so we can rewrite swapper. */
 	/* PGD */
-	mov	cur_pgdp, swapper_pa
-	add	end_pgdp, cur_pgdp, #(PTRS_PER_PGD * 8)
-do_pgd:	__idmap_kpti_get_pgtable_ent	pgd
-	tbnz	pgd, #1, walk_puds
-next_pgd:
-	__idmap_kpti_put_pgtable_ent_ng	pgd
-skip_pgd:
-	add	cur_pgdp, cur_pgdp, #8
-	cmp	cur_pgdp, end_pgdp
-	b.ne	do_pgd
-
-	/* Publish the updated tables and nuke all the TLBs */
-	dsb	sy
-	tlbi	vmalle1is
-	dsb	ish
-	isb
+	adrp		cur_pgdp, swapper_pg_dir
+	kpti_map_pgtbl	pgd, 0
+	kpti_mk_tbl_ng	pgd, PTRS_PER_PGD
 
-	/* We're done: fire up the MMU again */
-	mrs	x17, sctlr_el1
-	orr	x17, x17, #SCTLR_ELx_M
-	set_sctlr_el1	x17
+	/* Ensure all the updated entries are visible to secondary CPUs */
+	dsb	ishst
+
+	/* We're done: fire up swapper_pg_dir again */
+	__idmap_cpu_set_reserved_ttbr1 x8, x9
+	msr	ttbr1_el1, swapper_ttb
+	isb
 
 	/* Set the flag to zero to indicate that we're all done */
 	str	wzr, [flag_ptr]
 	ret
 
+.Lderef_pgd:
 	/* PUD */
-walk_puds:
-	.if CONFIG_PGTABLE_LEVELS > 3
+	.if		CONFIG_PGTABLE_LEVELS > 3
+	pud		.req	x10
 	pte_to_phys	cur_pudp, pgd
-	add	end_pudp, cur_pudp, #(PTRS_PER_PUD * 8)
-do_pud:	__idmap_kpti_get_pgtable_ent	pud
-	tbnz	pud, #1, walk_pmds
-next_pud:
-	__idmap_kpti_put_pgtable_ent_ng	pud
-skip_pud:
-	add	cur_pudp, cur_pudp, 8
-	cmp	cur_pudp, end_pudp
-	b.ne	do_pud
-	b	next_pgd
-	.else /* CONFIG_PGTABLE_LEVELS <= 3 */
-	mov	pud, pgd
-	b	walk_pmds
-next_pud:
-	b	next_pgd
+	kpti_map_pgtbl	pud, 1
+	kpti_mk_tbl_ng	pud, PTRS_PER_PUD
+	b		.Lnext_pgd
+	.else		/* CONFIG_PGTABLE_LEVELS <= 3 */
+	pud		.req	pgd
+	.set		.Lnext_pud, .Lnext_pgd
 	.endif
 
+.Lderef_pud:
 	/* PMD */
-walk_pmds:
-	.if CONFIG_PGTABLE_LEVELS > 2
+	.if		CONFIG_PGTABLE_LEVELS > 2
+	pmd		.req	x13
 	pte_to_phys	cur_pmdp, pud
-	add	end_pmdp, cur_pmdp, #(PTRS_PER_PMD * 8)
-do_pmd:	__idmap_kpti_get_pgtable_ent	pmd
-	tbnz	pmd, #1, walk_ptes
-next_pmd:
-	__idmap_kpti_put_pgtable_ent_ng	pmd
-skip_pmd:
-	add	cur_pmdp, cur_pmdp, #8
-	cmp	cur_pmdp, end_pmdp
-	b.ne	do_pmd
-	b	next_pud
-	.else /* CONFIG_PGTABLE_LEVELS <= 2 */
-	mov	pmd, pud
-	b	walk_ptes
-next_pmd:
-	b	next_pud
+	kpti_map_pgtbl	pmd, 2
+	kpti_mk_tbl_ng	pmd, PTRS_PER_PMD
+	b		.Lnext_pud
+	.else		/* CONFIG_PGTABLE_LEVELS <= 2 */
+	pmd		.req	pgd
+	.set		.Lnext_pmd, .Lnext_pgd
 	.endif
 
+.Lderef_pmd:
 	/* PTE */
-walk_ptes:
 	pte_to_phys	cur_ptep, pmd
-	add	end_ptep, cur_ptep, #(PTRS_PER_PTE * 8)
-do_pte:	__idmap_kpti_get_pgtable_ent	pte
-	__idmap_kpti_put_pgtable_ent_ng	pte
-skip_pte:
-	add	cur_ptep, cur_ptep, #8
-	cmp	cur_ptep, end_ptep
-	b.ne	do_pte
-	b	next_pmd
+	kpti_map_pgtbl	pte, 3
+	kpti_mk_tbl_ng	pte, PTRS_PER_PTE
+	b		.Lnext_pmd
 
 	.unreq	cpu
+	.unreq	temp_pte
 	.unreq	num_cpus
-	.unreq	swapper_pa
+	.unreq	pte_flags
+	.unreq	temp_pgd_phys
 	.unreq	cur_pgdp
 	.unreq	end_pgdp
 	.unreq	pgd
@@ -360,6 +366,7 @@ skip_pte:
 	.unreq	cur_ptep
 	.unreq	end_ptep
 	.unreq	pte
+	.unreq	valid
 
 	/* Secondary CPUs end up here */
 __idmap_kpti_secondary:
@@ -379,7 +386,6 @@ __idmap_kpti_secondary:
 	cbnz	w16, 1b
 
 	/* All done, act like nothing happened */
-	offset_ttbr1 swapper_ttb, x16
 	msr	ttbr1_el1, swapper_ttb
 	isb
 	ret
@@ -395,6 +401,8 @@ SYM_FUNC_END(idmap_kpti_install_ng_mappings)
  *
  *	Initialise the processor for turning the MMU on.
  *
+ * Input:
+ *	x0 - actual number of VA bits (ignored unless VA_BITS > 48)
  * Output:
  *	Return in x0 the value of the SCTLR_EL1 register.
  */
@@ -421,55 +429,16 @@ SYM_FUNC_START(__cpu_setup)
 	mov_q	mair, MAIR_EL1_SET
 	mov_q	tcr, TCR_TxSZ(VA_BITS) | TCR_CACHE_FLAGS | TCR_SMP_FLAGS | \
 			TCR_TG_FLAGS | TCR_KASLR_FLAGS | TCR_ASID16 | \
-			TCR_TBI0 | TCR_A1 | TCR_KASAN_SW_FLAGS
-
-#ifdef CONFIG_ARM64_MTE
-	/*
-	 * Update MAIR_EL1, GCR_EL1 and TFSR*_EL1 if MTE is supported
-	 * (ID_AA64PFR1_EL1[11:8] > 1).
-	 */
-	mrs	x10, ID_AA64PFR1_EL1
-	ubfx	x10, x10, #ID_AA64PFR1_MTE_SHIFT, #4
-	cmp	x10, #ID_AA64PFR1_MTE
-	b.lt	1f
-
-	/* Normal Tagged memory type at the corresponding MAIR index */
-	mov	x10, #MAIR_ATTR_NORMAL_TAGGED
-	bfi	mair, x10, #(8 *  MT_NORMAL_TAGGED), #8
-
-	mov	x10, #KERNEL_GCR_EL1
-	msr_s	SYS_GCR_EL1, x10
+			TCR_TBI0 | TCR_A1 | TCR_KASAN_SW_FLAGS | TCR_MTE_FLAGS
 
-	/*
-	 * If GCR_EL1.RRND=1 is implemented the same way as RRND=0, then
-	 * RGSR_EL1.SEED must be non-zero for IRG to produce
-	 * pseudorandom numbers. As RGSR_EL1 is UNKNOWN out of reset, we
-	 * must initialize it.
-	 */
-	mrs	x10, CNTVCT_EL0
-	ands	x10, x10, #SYS_RGSR_EL1_SEED_MASK
-	csinc	x10, x10, xzr, ne
-	lsl	x10, x10, #SYS_RGSR_EL1_SEED_SHIFT
-	msr_s	SYS_RGSR_EL1, x10
-
-	/* clear any pending tag check faults in TFSR*_EL1 */
-	msr_s	SYS_TFSR_EL1, xzr
-	msr_s	SYS_TFSRE0_EL1, xzr
-
-	/* set the TCR_EL1 bits */
-	mov_q	x10, TCR_MTE_FLAGS
-	orr	tcr, tcr, x10
-1:
-#endif
 	tcr_clear_errata_bits tcr, x9, x5
 
 #ifdef CONFIG_ARM64_VA_BITS_52
-	ldr_l		x9, vabits_actual
-	sub		x9, xzr, x9
+	sub		x9, xzr, x0
 	add		x9, x9, #64
 	tcr_set_t1sz	tcr, x9
 #else
-	ldr_l		x9, idmap_t0sz
+	idmap_get_t0sz	x9
 #endif
 	tcr_set_t0sz	tcr, x9
 
diff --git a/arch/arm64/mm/ptdump.c b/arch/arm64/mm/ptdump.c
index 1c403536c9bb..9bc4066c5bf3 100644
--- a/arch/arm64/mm/ptdump.c
+++ b/arch/arm64/mm/ptdump.c
@@ -41,8 +41,6 @@ static struct addr_marker address_markers[] = {
 	{ 0 /* KASAN_SHADOW_START */,	"Kasan shadow start" },
 	{ KASAN_SHADOW_END,		"Kasan shadow end" },
 #endif
-	{ BPF_JIT_REGION_START,		"BPF start" },
-	{ BPF_JIT_REGION_END,		"BPF end" },
 	{ MODULES_VADDR,		"Modules start" },
 	{ MODULES_END,			"Modules end" },
 	{ VMALLOC_START,		"vmalloc() area" },
diff --git a/arch/arm64/mm/trans_pgd.c b/arch/arm64/mm/trans_pgd.c
index d7da8ca40d2e..4ea2eefbc053 100644
--- a/arch/arm64/mm/trans_pgd.c
+++ b/arch/arm64/mm/trans_pgd.c
@@ -238,7 +238,7 @@ int trans_pgd_idmap_page(struct trans_pgd_info *info, phys_addr_t *trans_ttbr0,
 	int this_level, index, level_lsb, level_msb;
 
 	dst_addr &= PAGE_MASK;
-	prev_level_entry = pte_val(pfn_pte(pfn, PAGE_KERNEL_EXEC));
+	prev_level_entry = pte_val(pfn_pte(pfn, PAGE_KERNEL_ROX));
 
 	for (this_level = 3; this_level >= 0; this_level--) {
 		levels[this_level] = trans_alloc(info);
diff --git a/arch/arm64/net/bpf_jit.h b/arch/arm64/net/bpf_jit.h
index cc0cf0f5c7c3..a6acb94ea3d6 100644
--- a/arch/arm64/net/bpf_jit.h
+++ b/arch/arm64/net/bpf_jit.h
@@ -66,6 +66,26 @@
 #define A64_STR64(Xt, Xn, Xm) A64_LS_REG(Xt, Xn, Xm, 64, STORE)
 #define A64_LDR64(Xt, Xn, Xm) A64_LS_REG(Xt, Xn, Xm, 64, LOAD)
 
+/* Load/store register (immediate offset) */
+#define A64_LS_IMM(Rt, Rn, imm, size, type) \
+	aarch64_insn_gen_load_store_imm(Rt, Rn, imm, \
+		AARCH64_INSN_SIZE_##size, \
+		AARCH64_INSN_LDST_##type##_IMM_OFFSET)
+#define A64_STRBI(Wt, Xn, imm)  A64_LS_IMM(Wt, Xn, imm, 8, STORE)
+#define A64_LDRBI(Wt, Xn, imm)  A64_LS_IMM(Wt, Xn, imm, 8, LOAD)
+#define A64_STRHI(Wt, Xn, imm)  A64_LS_IMM(Wt, Xn, imm, 16, STORE)
+#define A64_LDRHI(Wt, Xn, imm)  A64_LS_IMM(Wt, Xn, imm, 16, LOAD)
+#define A64_STR32I(Wt, Xn, imm) A64_LS_IMM(Wt, Xn, imm, 32, STORE)
+#define A64_LDR32I(Wt, Xn, imm) A64_LS_IMM(Wt, Xn, imm, 32, LOAD)
+#define A64_STR64I(Xt, Xn, imm) A64_LS_IMM(Xt, Xn, imm, 64, STORE)
+#define A64_LDR64I(Xt, Xn, imm) A64_LS_IMM(Xt, Xn, imm, 64, LOAD)
+
+/* LDR (literal) */
+#define A64_LDR32LIT(Wt, offset) \
+	aarch64_insn_gen_load_literal(0, offset, Wt, false)
+#define A64_LDR64LIT(Xt, offset) \
+	aarch64_insn_gen_load_literal(0, offset, Xt, true)
+
 /* Load/store register pair */
 #define A64_LS_PAIR(Rt, Rt2, Rn, offset, ls, type) \
 	aarch64_insn_gen_load_store_pair(Rt, Rt2, Rn, offset, \
@@ -88,10 +108,42 @@
 /* [Rn] = Rt; (atomic) Rs = [state] */
 #define A64_STXR(sf, Rt, Rn, Rs) \
 	A64_LSX(sf, Rt, Rn, Rs, STORE_EX)
+/* [Rn] = Rt (store release); (atomic) Rs = [state] */
+#define A64_STLXR(sf, Rt, Rn, Rs) \
+	aarch64_insn_gen_load_store_ex(Rt, Rn, Rs, A64_SIZE(sf), \
+				       AARCH64_INSN_LDST_STORE_REL_EX)
+
+/*
+ * LSE atomics
+ *
+ * ST{ADD,CLR,SET,EOR} is simply encoded as an alias for
+ * LDD{ADD,CLR,SET,EOR} with XZR as the destination register.
+ */
+#define A64_ST_OP(sf, Rn, Rs, op) \
+	aarch64_insn_gen_atomic_ld_op(A64_ZR, Rn, Rs, \
+		A64_SIZE(sf), AARCH64_INSN_MEM_ATOMIC_##op, \
+		AARCH64_INSN_MEM_ORDER_NONE)
+/* [Rn] <op>= Rs */
+#define A64_STADD(sf, Rn, Rs) A64_ST_OP(sf, Rn, Rs, ADD)
+#define A64_STCLR(sf, Rn, Rs) A64_ST_OP(sf, Rn, Rs, CLR)
+#define A64_STEOR(sf, Rn, Rs) A64_ST_OP(sf, Rn, Rs, EOR)
+#define A64_STSET(sf, Rn, Rs) A64_ST_OP(sf, Rn, Rs, SET)
 
-/* LSE atomics */
-#define A64_STADD(sf, Rn, Rs) \
-	aarch64_insn_gen_stadd(Rn, Rs, A64_SIZE(sf))
+#define A64_LD_OP_AL(sf, Rt, Rn, Rs, op) \
+	aarch64_insn_gen_atomic_ld_op(Rt, Rn, Rs, \
+		A64_SIZE(sf), AARCH64_INSN_MEM_ATOMIC_##op, \
+		AARCH64_INSN_MEM_ORDER_ACQREL)
+/* Rt = [Rn] (load acquire); [Rn] <op>= Rs (store release) */
+#define A64_LDADDAL(sf, Rt, Rn, Rs) A64_LD_OP_AL(sf, Rt, Rn, Rs, ADD)
+#define A64_LDCLRAL(sf, Rt, Rn, Rs) A64_LD_OP_AL(sf, Rt, Rn, Rs, CLR)
+#define A64_LDEORAL(sf, Rt, Rn, Rs) A64_LD_OP_AL(sf, Rt, Rn, Rs, EOR)
+#define A64_LDSETAL(sf, Rt, Rn, Rs) A64_LD_OP_AL(sf, Rt, Rn, Rs, SET)
+/* Rt = [Rn] (load acquire); [Rn] = Rs (store release) */
+#define A64_SWPAL(sf, Rt, Rn, Rs) A64_LD_OP_AL(sf, Rt, Rn, Rs, SWP)
+/* Rs = CAS(Rn, Rs, Rt) (load acquire & store release) */
+#define A64_CASAL(sf, Rt, Rn, Rs) \
+	aarch64_insn_gen_cas(Rt, Rn, Rs, A64_SIZE(sf), \
+		AARCH64_INSN_MEM_ORDER_ACQREL)
 
 /* Add/subtract (immediate) */
 #define A64_ADDSUB_IMM(sf, Rd, Rn, imm12, type) \
@@ -196,6 +248,9 @@
 #define A64_ANDS(sf, Rd, Rn, Rm) A64_LOGIC_SREG(sf, Rd, Rn, Rm, AND_SETFLAGS)
 /* Rn & Rm; set condition flags */
 #define A64_TST(sf, Rn, Rm) A64_ANDS(sf, A64_ZR, Rn, Rm)
+/* Rd = ~Rm (alias of ORN with A64_ZR as Rn) */
+#define A64_MVN(sf, Rd, Rm)  \
+	A64_LOGIC_SREG(sf, Rd, A64_ZR, Rm, ORN)
 
 /* Logical (immediate) */
 #define A64_LOGIC_IMM(sf, Rd, Rn, imm, type) ({ \
@@ -214,9 +269,16 @@
 /* HINTs */
 #define A64_HINT(x) aarch64_insn_gen_hint(x)
 
+#define A64_PACIASP A64_HINT(AARCH64_INSN_HINT_PACIASP)
+#define A64_AUTIASP A64_HINT(AARCH64_INSN_HINT_AUTIASP)
+
 /* BTI */
 #define A64_BTI_C  A64_HINT(AARCH64_INSN_HINT_BTIC)
 #define A64_BTI_J  A64_HINT(AARCH64_INSN_HINT_BTIJ)
 #define A64_BTI_JC A64_HINT(AARCH64_INSN_HINT_BTIJC)
+#define A64_NOP    A64_HINT(AARCH64_INSN_HINT_NOP)
+
+/* DMB */
+#define A64_DMB_ISH aarch64_insn_gen_dmb(AARCH64_INSN_MB_ISH)
 
 #endif /* _BPF_JIT_H */
diff --git a/arch/arm64/net/bpf_jit_comp.c b/arch/arm64/net/bpf_jit_comp.c
index 3a8a7140a9bf..30f76178608b 100644
--- a/arch/arm64/net/bpf_jit_comp.c
+++ b/arch/arm64/net/bpf_jit_comp.c
@@ -10,6 +10,7 @@
 #include <linux/bitfield.h>
 #include <linux/bpf.h>
 #include <linux/filter.h>
+#include <linux/memory.h>
 #include <linux/printk.h>
 #include <linux/slab.h>
 
@@ -18,6 +19,7 @@
 #include <asm/cacheflush.h>
 #include <asm/debug-monitors.h>
 #include <asm/insn.h>
+#include <asm/patching.h>
 #include <asm/set_memory.h>
 
 #include "bpf_jit.h"
@@ -26,6 +28,18 @@
 #define TMP_REG_2 (MAX_BPF_JIT_REG + 1)
 #define TCALL_CNT (MAX_BPF_JIT_REG + 2)
 #define TMP_REG_3 (MAX_BPF_JIT_REG + 3)
+#define FP_BOTTOM (MAX_BPF_JIT_REG + 4)
+
+#define check_imm(bits, imm) do {				\
+	if ((((imm) > 0) && ((imm) >> (bits))) ||		\
+	    (((imm) < 0) && (~(imm) >> (bits)))) {		\
+		pr_info("[%2d] imm=%d(0x%x) out of range\n",	\
+			i, imm, imm);				\
+		return -EINVAL;					\
+	}							\
+} while (0)
+#define check_imm19(imm) check_imm(19, imm)
+#define check_imm26(imm) check_imm(26, imm)
 
 /* Map BPF registers to A64 registers */
 static const int bpf2a64[] = {
@@ -44,7 +58,7 @@ static const int bpf2a64[] = {
 	[BPF_REG_9] = A64_R(22),
 	/* read-only frame pointer to access stack */
 	[BPF_REG_FP] = A64_R(25),
-	/* temporary registers for internal BPF JIT */
+	/* temporary registers for BPF JIT */
 	[TMP_REG_1] = A64_R(10),
 	[TMP_REG_2] = A64_R(11),
 	[TMP_REG_3] = A64_R(12),
@@ -52,6 +66,7 @@ static const int bpf2a64[] = {
 	[TCALL_CNT] = A64_R(26),
 	/* temporary register for blinding constants */
 	[BPF_REG_AX] = A64_R(9),
+	[FP_BOTTOM] = A64_R(27),
 };
 
 struct jit_ctx {
@@ -62,8 +77,18 @@ struct jit_ctx {
 	int exentry_idx;
 	__le32 *image;
 	u32 stack_size;
+	int fpb_offset;
+};
+
+struct bpf_plt {
+	u32 insn_ldr; /* load target */
+	u32 insn_br;  /* branch to target */
+	u64 target;   /* target value */
 };
 
+#define PLT_TARGET_SIZE   sizeof_field(struct bpf_plt, target)
+#define PLT_TARGET_OFFSET offsetof(struct bpf_plt, target)
+
 static inline void emit(const u32 insn, struct jit_ctx *ctx)
 {
 	if (ctx->image != NULL)
@@ -126,6 +151,12 @@ static inline void emit_a64_mov_i64(const int reg, const u64 val,
 	}
 }
 
+static inline void emit_bti(u32 insn, struct jit_ctx *ctx)
+{
+	if (IS_ENABLED(CONFIG_ARM64_BTI_KERNEL))
+		emit(insn, ctx);
+}
+
 /*
  * Kernel addresses in the vmalloc space use at most 48 bits, and the
  * remaining bits are guaranteed to be 0x1. So we can compose the address
@@ -145,6 +176,14 @@ static inline void emit_addr_mov_i64(const int reg, const u64 val,
 	}
 }
 
+static inline void emit_call(u64 target, struct jit_ctx *ctx)
+{
+	u8 tmp = bpf2a64[TMP_REG_1];
+
+	emit_addr_mov_i64(tmp, target, ctx);
+	emit(A64_BLR(tmp), ctx);
+}
+
 static inline int bpf2a64_offset(int bpf_insn, int off,
 				 const struct jit_ctx *ctx)
 {
@@ -180,22 +219,83 @@ static bool is_addsub_imm(u32 imm)
 	return !(imm & ~0xfff) || !(imm & ~0xfff000);
 }
 
+/*
+ * There are 3 types of AArch64 LDR/STR (immediate) instruction:
+ * Post-index, Pre-index, Unsigned offset.
+ *
+ * For BPF ldr/str, the "unsigned offset" type is sufficient.
+ *
+ * "Unsigned offset" type LDR(immediate) format:
+ *
+ *    3                   2                   1                   0
+ *  1 0 9 8 7 6 5 4 3 2 1 0 9 8 7 6 5 4 3 2 1 0 9 8 7 6 5 4 3 2 1 0
+ * +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
+ * |x x|1 1 1 0 0 1 0 1|         imm12         |    Rn   |    Rt   |
+ * +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
+ * scale
+ *
+ * "Unsigned offset" type STR(immediate) format:
+ *    3                   2                   1                   0
+ *  1 0 9 8 7 6 5 4 3 2 1 0 9 8 7 6 5 4 3 2 1 0 9 8 7 6 5 4 3 2 1 0
+ * +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
+ * |x x|1 1 1 0 0 1 0 0|         imm12         |    Rn   |    Rt   |
+ * +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
+ * scale
+ *
+ * The offset is calculated from imm12 and scale in the following way:
+ *
+ * offset = (u64)imm12 << scale
+ */
+static bool is_lsi_offset(int offset, int scale)
+{
+	if (offset < 0)
+		return false;
+
+	if (offset > (0xFFF << scale))
+		return false;
+
+	if (offset & ((1 << scale) - 1))
+		return false;
+
+	return true;
+}
+
+/* generated prologue:
+ *      bti c // if CONFIG_ARM64_BTI_KERNEL
+ *      mov x9, lr
+ *      nop  // POKE_OFFSET
+ *      paciasp // if CONFIG_ARM64_PTR_AUTH_KERNEL
+ *      stp x29, lr, [sp, #-16]!
+ *      mov x29, sp
+ *      stp x19, x20, [sp, #-16]!
+ *      stp x21, x22, [sp, #-16]!
+ *      stp x25, x26, [sp, #-16]!
+ *      stp x27, x28, [sp, #-16]!
+ *      mov x25, sp
+ *      mov tcc, #0
+ *      // PROLOGUE_OFFSET
+ */
+
+#define BTI_INSNS (IS_ENABLED(CONFIG_ARM64_BTI_KERNEL) ? 1 : 0)
+#define PAC_INSNS (IS_ENABLED(CONFIG_ARM64_PTR_AUTH_KERNEL) ? 1 : 0)
+
+/* Offset of nop instruction in bpf prog entry to be poked */
+#define POKE_OFFSET (BTI_INSNS + 1)
+
 /* Tail call offset to jump into */
-#if IS_ENABLED(CONFIG_ARM64_BTI_KERNEL)
-#define PROLOGUE_OFFSET 8
-#else
-#define PROLOGUE_OFFSET 7
-#endif
+#define PROLOGUE_OFFSET (BTI_INSNS + 2 + PAC_INSNS + 8)
 
 static int build_prologue(struct jit_ctx *ctx, bool ebpf_from_cbpf)
 {
 	const struct bpf_prog *prog = ctx->prog;
+	const bool is_main_prog = prog->aux->func_idx == 0;
 	const u8 r6 = bpf2a64[BPF_REG_6];
 	const u8 r7 = bpf2a64[BPF_REG_7];
 	const u8 r8 = bpf2a64[BPF_REG_8];
 	const u8 r9 = bpf2a64[BPF_REG_9];
 	const u8 fp = bpf2a64[BPF_REG_FP];
 	const u8 tcc = bpf2a64[TCALL_CNT];
+	const u8 fpb = bpf2a64[FP_BOTTOM];
 	const int idx0 = ctx->idx;
 	int cur_offset;
 
@@ -222,9 +322,14 @@ static int build_prologue(struct jit_ctx *ctx, bool ebpf_from_cbpf)
 	 *
 	 */
 
-	/* BTI landing pad */
-	if (IS_ENABLED(CONFIG_ARM64_BTI_KERNEL))
-		emit(A64_BTI_C, ctx);
+	emit_bti(A64_BTI_C, ctx);
+
+	emit(A64_MOV(1, A64_R(9), A64_LR), ctx);
+	emit(A64_NOP, ctx);
+
+	/* Sign lr */
+	if (IS_ENABLED(CONFIG_ARM64_PTR_AUTH_KERNEL))
+		emit(A64_PACIASP, ctx);
 
 	/* Save FP and LR registers to stay align with ARM64 AAPCS */
 	emit(A64_PUSH(A64_FP, A64_LR, A64_SP), ctx);
@@ -234,11 +339,12 @@ static int build_prologue(struct jit_ctx *ctx, bool ebpf_from_cbpf)
 	emit(A64_PUSH(r6, r7, A64_SP), ctx);
 	emit(A64_PUSH(r8, r9, A64_SP), ctx);
 	emit(A64_PUSH(fp, tcc, A64_SP), ctx);
+	emit(A64_PUSH(fpb, A64_R(28), A64_SP), ctx);
 
 	/* Set up BPF prog stack base register */
 	emit(A64_MOV(1, fp, A64_SP), ctx);
 
-	if (!ebpf_from_cbpf) {
+	if (!ebpf_from_cbpf && is_main_prog) {
 		/* Initialize tail_call_cnt */
 		emit(A64_MOVZ(1, tcc, 0, 0), ctx);
 
@@ -250,10 +356,11 @@ static int build_prologue(struct jit_ctx *ctx, bool ebpf_from_cbpf)
 		}
 
 		/* BTI landing pad for the tail call, done with a BR */
-		if (IS_ENABLED(CONFIG_ARM64_BTI_KERNEL))
-			emit(A64_BTI_J, ctx);
+		emit_bti(A64_BTI_J, ctx);
 	}
 
+	emit(A64_SUB_I(1, fpb, fp, ctx->fpb_offset), ctx);
+
 	/* Stack must be multiples of 16B */
 	ctx->stack_size = round_up(prog->aux->stack_depth, 16);
 
@@ -287,13 +394,14 @@ static int emit_bpf_tail_call(struct jit_ctx *ctx)
 	emit(A64_CMP(0, r3, tmp), ctx);
 	emit(A64_B_(A64_COND_CS, jmp_offset), ctx);
 
-	/* if (tail_call_cnt > MAX_TAIL_CALL_CNT)
+	/*
+	 * if (tail_call_cnt >= MAX_TAIL_CALL_CNT)
 	 *     goto out;
 	 * tail_call_cnt++;
 	 */
 	emit_a64_mov_i64(tmp, MAX_TAIL_CALL_CNT, ctx);
 	emit(A64_CMP(1, tcc, tmp), ctx);
-	emit(A64_B_(A64_COND_HI, jmp_offset), ctx);
+	emit(A64_B_(A64_COND_CS, jmp_offset), ctx);
 	emit(A64_ADD_I(1, tcc, tcc, 1), ctx);
 
 	/* prog = array->ptrs[index];
@@ -328,6 +436,217 @@ static int emit_bpf_tail_call(struct jit_ctx *ctx)
 #undef jmp_offset
 }
 
+#ifdef CONFIG_ARM64_LSE_ATOMICS
+static int emit_lse_atomic(const struct bpf_insn *insn, struct jit_ctx *ctx)
+{
+	const u8 code = insn->code;
+	const u8 dst = bpf2a64[insn->dst_reg];
+	const u8 src = bpf2a64[insn->src_reg];
+	const u8 tmp = bpf2a64[TMP_REG_1];
+	const u8 tmp2 = bpf2a64[TMP_REG_2];
+	const bool isdw = BPF_SIZE(code) == BPF_DW;
+	const s16 off = insn->off;
+	u8 reg;
+
+	if (!off) {
+		reg = dst;
+	} else {
+		emit_a64_mov_i(1, tmp, off, ctx);
+		emit(A64_ADD(1, tmp, tmp, dst), ctx);
+		reg = tmp;
+	}
+
+	switch (insn->imm) {
+	/* lock *(u32/u64 *)(dst_reg + off) <op>= src_reg */
+	case BPF_ADD:
+		emit(A64_STADD(isdw, reg, src), ctx);
+		break;
+	case BPF_AND:
+		emit(A64_MVN(isdw, tmp2, src), ctx);
+		emit(A64_STCLR(isdw, reg, tmp2), ctx);
+		break;
+	case BPF_OR:
+		emit(A64_STSET(isdw, reg, src), ctx);
+		break;
+	case BPF_XOR:
+		emit(A64_STEOR(isdw, reg, src), ctx);
+		break;
+	/* src_reg = atomic_fetch_<op>(dst_reg + off, src_reg) */
+	case BPF_ADD | BPF_FETCH:
+		emit(A64_LDADDAL(isdw, src, reg, src), ctx);
+		break;
+	case BPF_AND | BPF_FETCH:
+		emit(A64_MVN(isdw, tmp2, src), ctx);
+		emit(A64_LDCLRAL(isdw, src, reg, tmp2), ctx);
+		break;
+	case BPF_OR | BPF_FETCH:
+		emit(A64_LDSETAL(isdw, src, reg, src), ctx);
+		break;
+	case BPF_XOR | BPF_FETCH:
+		emit(A64_LDEORAL(isdw, src, reg, src), ctx);
+		break;
+	/* src_reg = atomic_xchg(dst_reg + off, src_reg); */
+	case BPF_XCHG:
+		emit(A64_SWPAL(isdw, src, reg, src), ctx);
+		break;
+	/* r0 = atomic_cmpxchg(dst_reg + off, r0, src_reg); */
+	case BPF_CMPXCHG:
+		emit(A64_CASAL(isdw, src, reg, bpf2a64[BPF_REG_0]), ctx);
+		break;
+	default:
+		pr_err_once("unknown atomic op code %02x\n", insn->imm);
+		return -EINVAL;
+	}
+
+	return 0;
+}
+#else
+static inline int emit_lse_atomic(const struct bpf_insn *insn, struct jit_ctx *ctx)
+{
+	return -EINVAL;
+}
+#endif
+
+static int emit_ll_sc_atomic(const struct bpf_insn *insn, struct jit_ctx *ctx)
+{
+	const u8 code = insn->code;
+	const u8 dst = bpf2a64[insn->dst_reg];
+	const u8 src = bpf2a64[insn->src_reg];
+	const u8 tmp = bpf2a64[TMP_REG_1];
+	const u8 tmp2 = bpf2a64[TMP_REG_2];
+	const u8 tmp3 = bpf2a64[TMP_REG_3];
+	const int i = insn - ctx->prog->insnsi;
+	const s32 imm = insn->imm;
+	const s16 off = insn->off;
+	const bool isdw = BPF_SIZE(code) == BPF_DW;
+	u8 reg;
+	s32 jmp_offset;
+
+	if (!off) {
+		reg = dst;
+	} else {
+		emit_a64_mov_i(1, tmp, off, ctx);
+		emit(A64_ADD(1, tmp, tmp, dst), ctx);
+		reg = tmp;
+	}
+
+	if (imm == BPF_ADD || imm == BPF_AND ||
+	    imm == BPF_OR || imm == BPF_XOR) {
+		/* lock *(u32/u64 *)(dst_reg + off) <op>= src_reg */
+		emit(A64_LDXR(isdw, tmp2, reg), ctx);
+		if (imm == BPF_ADD)
+			emit(A64_ADD(isdw, tmp2, tmp2, src), ctx);
+		else if (imm == BPF_AND)
+			emit(A64_AND(isdw, tmp2, tmp2, src), ctx);
+		else if (imm == BPF_OR)
+			emit(A64_ORR(isdw, tmp2, tmp2, src), ctx);
+		else
+			emit(A64_EOR(isdw, tmp2, tmp2, src), ctx);
+		emit(A64_STXR(isdw, tmp2, reg, tmp3), ctx);
+		jmp_offset = -3;
+		check_imm19(jmp_offset);
+		emit(A64_CBNZ(0, tmp3, jmp_offset), ctx);
+	} else if (imm == (BPF_ADD | BPF_FETCH) ||
+		   imm == (BPF_AND | BPF_FETCH) ||
+		   imm == (BPF_OR | BPF_FETCH) ||
+		   imm == (BPF_XOR | BPF_FETCH)) {
+		/* src_reg = atomic_fetch_<op>(dst_reg + off, src_reg) */
+		const u8 ax = bpf2a64[BPF_REG_AX];
+
+		emit(A64_MOV(isdw, ax, src), ctx);
+		emit(A64_LDXR(isdw, src, reg), ctx);
+		if (imm == (BPF_ADD | BPF_FETCH))
+			emit(A64_ADD(isdw, tmp2, src, ax), ctx);
+		else if (imm == (BPF_AND | BPF_FETCH))
+			emit(A64_AND(isdw, tmp2, src, ax), ctx);
+		else if (imm == (BPF_OR | BPF_FETCH))
+			emit(A64_ORR(isdw, tmp2, src, ax), ctx);
+		else
+			emit(A64_EOR(isdw, tmp2, src, ax), ctx);
+		emit(A64_STLXR(isdw, tmp2, reg, tmp3), ctx);
+		jmp_offset = -3;
+		check_imm19(jmp_offset);
+		emit(A64_CBNZ(0, tmp3, jmp_offset), ctx);
+		emit(A64_DMB_ISH, ctx);
+	} else if (imm == BPF_XCHG) {
+		/* src_reg = atomic_xchg(dst_reg + off, src_reg); */
+		emit(A64_MOV(isdw, tmp2, src), ctx);
+		emit(A64_LDXR(isdw, src, reg), ctx);
+		emit(A64_STLXR(isdw, tmp2, reg, tmp3), ctx);
+		jmp_offset = -2;
+		check_imm19(jmp_offset);
+		emit(A64_CBNZ(0, tmp3, jmp_offset), ctx);
+		emit(A64_DMB_ISH, ctx);
+	} else if (imm == BPF_CMPXCHG) {
+		/* r0 = atomic_cmpxchg(dst_reg + off, r0, src_reg); */
+		const u8 r0 = bpf2a64[BPF_REG_0];
+
+		emit(A64_MOV(isdw, tmp2, r0), ctx);
+		emit(A64_LDXR(isdw, r0, reg), ctx);
+		emit(A64_EOR(isdw, tmp3, r0, tmp2), ctx);
+		jmp_offset = 4;
+		check_imm19(jmp_offset);
+		emit(A64_CBNZ(isdw, tmp3, jmp_offset), ctx);
+		emit(A64_STLXR(isdw, src, reg, tmp3), ctx);
+		jmp_offset = -4;
+		check_imm19(jmp_offset);
+		emit(A64_CBNZ(0, tmp3, jmp_offset), ctx);
+		emit(A64_DMB_ISH, ctx);
+	} else {
+		pr_err_once("unknown atomic op code %02x\n", imm);
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+void dummy_tramp(void);
+
+asm (
+"	.pushsection .text, \"ax\", @progbits\n"
+"	.global dummy_tramp\n"
+"	.type dummy_tramp, %function\n"
+"dummy_tramp:"
+#if IS_ENABLED(CONFIG_ARM64_BTI_KERNEL)
+"	bti j\n" /* dummy_tramp is called via "br x10" */
+#endif
+"	mov x10, x30\n"
+"	mov x30, x9\n"
+"	ret x10\n"
+"	.size dummy_tramp, .-dummy_tramp\n"
+"	.popsection\n"
+);
+
+/* build a plt initialized like this:
+ *
+ * plt:
+ *      ldr tmp, target
+ *      br tmp
+ * target:
+ *      .quad dummy_tramp
+ *
+ * when a long jump trampoline is attached, target is filled with the
+ * trampoline address, and when the trampoline is removed, target is
+ * restored to dummy_tramp address.
+ */
+static void build_plt(struct jit_ctx *ctx)
+{
+	const u8 tmp = bpf2a64[TMP_REG_1];
+	struct bpf_plt *plt = NULL;
+
+	/* make sure target is 64-bit aligned */
+	if ((ctx->idx + PLT_TARGET_OFFSET / AARCH64_INSN_SIZE) % 2)
+		emit(A64_NOP, ctx);
+
+	plt = (struct bpf_plt *)(ctx->image + ctx->idx);
+	/* plt is called via bl, no BTI needed here */
+	emit(A64_LDR64LIT(tmp, 2 * AARCH64_INSN_SIZE), ctx);
+	emit(A64_BR(tmp), ctx);
+
+	if (ctx->image)
+		plt->target = (u64)&dummy_tramp;
+}
+
 static void build_epilogue(struct jit_ctx *ctx)
 {
 	const u8 r0 = bpf2a64[BPF_REG_0];
@@ -336,10 +655,13 @@ static void build_epilogue(struct jit_ctx *ctx)
 	const u8 r8 = bpf2a64[BPF_REG_8];
 	const u8 r9 = bpf2a64[BPF_REG_9];
 	const u8 fp = bpf2a64[BPF_REG_FP];
+	const u8 fpb = bpf2a64[FP_BOTTOM];
 
 	/* We're done with BPF stack */
 	emit(A64_ADD_I(1, A64_SP, A64_SP, ctx->stack_size), ctx);
 
+	/* Restore x27 and x28 */
+	emit(A64_POP(fpb, A64_R(28), A64_SP), ctx);
 	/* Restore fs (x25) and x26 */
 	emit(A64_POP(fp, A64_R(26), A64_SP), ctx);
 
@@ -353,6 +675,10 @@ static void build_epilogue(struct jit_ctx *ctx)
 	/* Set return value */
 	emit(A64_MOV(1, A64_R(0), r0), ctx);
 
+	/* Authenticate lr */
+	if (IS_ENABLED(CONFIG_ARM64_PTR_AUTH_KERNEL))
+		emit(A64_AUTIASP, ctx);
+
 	emit(A64_RET(A64_LR), ctx);
 }
 
@@ -433,29 +759,21 @@ static int build_insn(const struct bpf_insn *insn, struct jit_ctx *ctx,
 	const u8 src = bpf2a64[insn->src_reg];
 	const u8 tmp = bpf2a64[TMP_REG_1];
 	const u8 tmp2 = bpf2a64[TMP_REG_2];
-	const u8 tmp3 = bpf2a64[TMP_REG_3];
+	const u8 fp = bpf2a64[BPF_REG_FP];
+	const u8 fpb = bpf2a64[FP_BOTTOM];
 	const s16 off = insn->off;
 	const s32 imm = insn->imm;
 	const int i = insn - ctx->prog->insnsi;
 	const bool is64 = BPF_CLASS(code) == BPF_ALU64 ||
 			  BPF_CLASS(code) == BPF_JMP;
-	const bool isdw = BPF_SIZE(code) == BPF_DW;
-	u8 jmp_cond, reg;
+	u8 jmp_cond;
 	s32 jmp_offset;
 	u32 a64_insn;
+	u8 src_adj;
+	u8 dst_adj;
+	int off_adj;
 	int ret;
 
-#define check_imm(bits, imm) do {				\
-	if ((((imm) > 0) && ((imm) >> (bits))) ||		\
-	    (((imm) < 0) && (~(imm) >> (bits)))) {		\
-		pr_info("[%2d] imm=%d(0x%x) out of range\n",	\
-			i, imm, imm);				\
-		return -EINVAL;					\
-	}							\
-} while (0)
-#define check_imm19(imm) check_imm(19, imm)
-#define check_imm26(imm) check_imm(26, imm)
-
 	switch (code) {
 	/* dst = src */
 	case BPF_ALU | BPF_MOV | BPF_X:
@@ -763,8 +1081,7 @@ emit_cond_jmp:
 					    &func_addr, &func_addr_fixed);
 		if (ret < 0)
 			return ret;
-		emit_addr_mov_i64(tmp, func_addr, ctx);
-		emit(A64_BLR(tmp), ctx);
+		emit_call(func_addr, ctx);
 		emit(A64_MOV(1, r0, A64_R(0)), ctx);
 		break;
 	}
@@ -791,7 +1108,10 @@ emit_cond_jmp:
 		u64 imm64;
 
 		imm64 = (u64)insn1.imm << 32 | (u32)imm;
-		emit_a64_mov_i64(dst, imm64, ctx);
+		if (bpf_pseudo_func(insn))
+			emit_addr_mov_i64(dst, imm64, ctx);
+		else
+			emit_a64_mov_i64(dst, imm64, ctx);
 
 		return 1;
 	}
@@ -805,19 +1125,45 @@ emit_cond_jmp:
 	case BPF_LDX | BPF_PROBE_MEM | BPF_W:
 	case BPF_LDX | BPF_PROBE_MEM | BPF_H:
 	case BPF_LDX | BPF_PROBE_MEM | BPF_B:
-		emit_a64_mov_i(1, tmp, off, ctx);
+		if (ctx->fpb_offset > 0 && src == fp) {
+			src_adj = fpb;
+			off_adj = off + ctx->fpb_offset;
+		} else {
+			src_adj = src;
+			off_adj = off;
+		}
 		switch (BPF_SIZE(code)) {
 		case BPF_W:
-			emit(A64_LDR32(dst, src, tmp), ctx);
+			if (is_lsi_offset(off_adj, 2)) {
+				emit(A64_LDR32I(dst, src_adj, off_adj), ctx);
+			} else {
+				emit_a64_mov_i(1, tmp, off, ctx);
+				emit(A64_LDR32(dst, src, tmp), ctx);
+			}
 			break;
 		case BPF_H:
-			emit(A64_LDRH(dst, src, tmp), ctx);
+			if (is_lsi_offset(off_adj, 1)) {
+				emit(A64_LDRHI(dst, src_adj, off_adj), ctx);
+			} else {
+				emit_a64_mov_i(1, tmp, off, ctx);
+				emit(A64_LDRH(dst, src, tmp), ctx);
+			}
 			break;
 		case BPF_B:
-			emit(A64_LDRB(dst, src, tmp), ctx);
+			if (is_lsi_offset(off_adj, 0)) {
+				emit(A64_LDRBI(dst, src_adj, off_adj), ctx);
+			} else {
+				emit_a64_mov_i(1, tmp, off, ctx);
+				emit(A64_LDRB(dst, src, tmp), ctx);
+			}
 			break;
 		case BPF_DW:
-			emit(A64_LDR64(dst, src, tmp), ctx);
+			if (is_lsi_offset(off_adj, 3)) {
+				emit(A64_LDR64I(dst, src_adj, off_adj), ctx);
+			} else {
+				emit_a64_mov_i(1, tmp, off, ctx);
+				emit(A64_LDR64(dst, src, tmp), ctx);
+			}
 			break;
 		}
 
@@ -844,21 +1190,47 @@ emit_cond_jmp:
 	case BPF_ST | BPF_MEM | BPF_H:
 	case BPF_ST | BPF_MEM | BPF_B:
 	case BPF_ST | BPF_MEM | BPF_DW:
+		if (ctx->fpb_offset > 0 && dst == fp) {
+			dst_adj = fpb;
+			off_adj = off + ctx->fpb_offset;
+		} else {
+			dst_adj = dst;
+			off_adj = off;
+		}
 		/* Load imm to a register then store it */
-		emit_a64_mov_i(1, tmp2, off, ctx);
 		emit_a64_mov_i(1, tmp, imm, ctx);
 		switch (BPF_SIZE(code)) {
 		case BPF_W:
-			emit(A64_STR32(tmp, dst, tmp2), ctx);
+			if (is_lsi_offset(off_adj, 2)) {
+				emit(A64_STR32I(tmp, dst_adj, off_adj), ctx);
+			} else {
+				emit_a64_mov_i(1, tmp2, off, ctx);
+				emit(A64_STR32(tmp, dst, tmp2), ctx);
+			}
 			break;
 		case BPF_H:
-			emit(A64_STRH(tmp, dst, tmp2), ctx);
+			if (is_lsi_offset(off_adj, 1)) {
+				emit(A64_STRHI(tmp, dst_adj, off_adj), ctx);
+			} else {
+				emit_a64_mov_i(1, tmp2, off, ctx);
+				emit(A64_STRH(tmp, dst, tmp2), ctx);
+			}
 			break;
 		case BPF_B:
-			emit(A64_STRB(tmp, dst, tmp2), ctx);
+			if (is_lsi_offset(off_adj, 0)) {
+				emit(A64_STRBI(tmp, dst_adj, off_adj), ctx);
+			} else {
+				emit_a64_mov_i(1, tmp2, off, ctx);
+				emit(A64_STRB(tmp, dst, tmp2), ctx);
+			}
 			break;
 		case BPF_DW:
-			emit(A64_STR64(tmp, dst, tmp2), ctx);
+			if (is_lsi_offset(off_adj, 3)) {
+				emit(A64_STR64I(tmp, dst_adj, off_adj), ctx);
+			} else {
+				emit_a64_mov_i(1, tmp2, off, ctx);
+				emit(A64_STR64(tmp, dst, tmp2), ctx);
+			}
 			break;
 		}
 		break;
@@ -868,52 +1240,57 @@ emit_cond_jmp:
 	case BPF_STX | BPF_MEM | BPF_H:
 	case BPF_STX | BPF_MEM | BPF_B:
 	case BPF_STX | BPF_MEM | BPF_DW:
-		emit_a64_mov_i(1, tmp, off, ctx);
+		if (ctx->fpb_offset > 0 && dst == fp) {
+			dst_adj = fpb;
+			off_adj = off + ctx->fpb_offset;
+		} else {
+			dst_adj = dst;
+			off_adj = off;
+		}
 		switch (BPF_SIZE(code)) {
 		case BPF_W:
-			emit(A64_STR32(src, dst, tmp), ctx);
+			if (is_lsi_offset(off_adj, 2)) {
+				emit(A64_STR32I(src, dst_adj, off_adj), ctx);
+			} else {
+				emit_a64_mov_i(1, tmp, off, ctx);
+				emit(A64_STR32(src, dst, tmp), ctx);
+			}
 			break;
 		case BPF_H:
-			emit(A64_STRH(src, dst, tmp), ctx);
+			if (is_lsi_offset(off_adj, 1)) {
+				emit(A64_STRHI(src, dst_adj, off_adj), ctx);
+			} else {
+				emit_a64_mov_i(1, tmp, off, ctx);
+				emit(A64_STRH(src, dst, tmp), ctx);
+			}
 			break;
 		case BPF_B:
-			emit(A64_STRB(src, dst, tmp), ctx);
+			if (is_lsi_offset(off_adj, 0)) {
+				emit(A64_STRBI(src, dst_adj, off_adj), ctx);
+			} else {
+				emit_a64_mov_i(1, tmp, off, ctx);
+				emit(A64_STRB(src, dst, tmp), ctx);
+			}
 			break;
 		case BPF_DW:
-			emit(A64_STR64(src, dst, tmp), ctx);
+			if (is_lsi_offset(off_adj, 3)) {
+				emit(A64_STR64I(src, dst_adj, off_adj), ctx);
+			} else {
+				emit_a64_mov_i(1, tmp, off, ctx);
+				emit(A64_STR64(src, dst, tmp), ctx);
+			}
 			break;
 		}
 		break;
 
 	case BPF_STX | BPF_ATOMIC | BPF_W:
 	case BPF_STX | BPF_ATOMIC | BPF_DW:
-		if (insn->imm != BPF_ADD) {
-			pr_err_once("unknown atomic op code %02x\n", insn->imm);
-			return -EINVAL;
-		}
-
-		/* STX XADD: lock *(u32 *)(dst + off) += src
-		 * and
-		 * STX XADD: lock *(u64 *)(dst + off) += src
-		 */
-
-		if (!off) {
-			reg = dst;
-		} else {
-			emit_a64_mov_i(1, tmp, off, ctx);
-			emit(A64_ADD(1, tmp, tmp, dst), ctx);
-			reg = tmp;
-		}
-		if (cpus_have_cap(ARM64_HAS_LSE_ATOMICS)) {
-			emit(A64_STADD(isdw, reg, src), ctx);
-		} else {
-			emit(A64_LDXR(isdw, tmp2, reg), ctx);
-			emit(A64_ADD(isdw, tmp2, tmp2, src), ctx);
-			emit(A64_STXR(isdw, tmp2, reg, tmp3), ctx);
-			jmp_offset = -3;
-			check_imm19(jmp_offset);
-			emit(A64_CBNZ(0, tmp3, jmp_offset), ctx);
-		}
+		if (cpus_have_cap(ARM64_HAS_LSE_ATOMICS))
+			ret = emit_lse_atomic(insn, ctx);
+		else
+			ret = emit_ll_sc_atomic(insn, ctx);
+		if (ret)
+			return ret;
 		break;
 
 	default:
@@ -924,6 +1301,79 @@ emit_cond_jmp:
 	return 0;
 }
 
+/*
+ * Return 0 if FP may change at runtime, otherwise find the minimum negative
+ * offset to FP, converts it to positive number, and align down to 8 bytes.
+ */
+static int find_fpb_offset(struct bpf_prog *prog)
+{
+	int i;
+	int offset = 0;
+
+	for (i = 0; i < prog->len; i++) {
+		const struct bpf_insn *insn = &prog->insnsi[i];
+		const u8 class = BPF_CLASS(insn->code);
+		const u8 mode = BPF_MODE(insn->code);
+		const u8 src = insn->src_reg;
+		const u8 dst = insn->dst_reg;
+		const s32 imm = insn->imm;
+		const s16 off = insn->off;
+
+		switch (class) {
+		case BPF_STX:
+		case BPF_ST:
+			/* fp holds atomic operation result */
+			if (class == BPF_STX && mode == BPF_ATOMIC &&
+			    ((imm == BPF_XCHG ||
+			      imm == (BPF_FETCH | BPF_ADD) ||
+			      imm == (BPF_FETCH | BPF_AND) ||
+			      imm == (BPF_FETCH | BPF_XOR) ||
+			      imm == (BPF_FETCH | BPF_OR)) &&
+			     src == BPF_REG_FP))
+				return 0;
+
+			if (mode == BPF_MEM && dst == BPF_REG_FP &&
+			    off < offset)
+				offset = insn->off;
+			break;
+
+		case BPF_JMP32:
+		case BPF_JMP:
+			break;
+
+		case BPF_LDX:
+		case BPF_LD:
+			/* fp holds load result */
+			if (dst == BPF_REG_FP)
+				return 0;
+
+			if (class == BPF_LDX && mode == BPF_MEM &&
+			    src == BPF_REG_FP && off < offset)
+				offset = off;
+			break;
+
+		case BPF_ALU:
+		case BPF_ALU64:
+		default:
+			/* fp holds ALU result */
+			if (dst == BPF_REG_FP)
+				return 0;
+		}
+	}
+
+	if (offset < 0) {
+		/*
+		 * safely be converted to a positive 'int', since insn->off
+		 * is 's16'
+		 */
+		offset = -offset;
+		/* align down to 8 bytes */
+		offset = ALIGN_DOWN(offset, 8);
+	}
+
+	return offset;
+}
+
 static int build_body(struct jit_ctx *ctx, bool extra_pass)
 {
 	const struct bpf_prog *prog = ctx->prog;
@@ -975,6 +1425,13 @@ static int validate_code(struct jit_ctx *ctx)
 		if (a64_insn == AARCH64_BREAK_FAULT)
 			return -1;
 	}
+	return 0;
+}
+
+static int validate_ctx(struct jit_ctx *ctx)
+{
+	if (validate_code(ctx))
+		return -1;
 
 	if (WARN_ON_ONCE(ctx->exentry_idx != ctx->prog->aux->num_exentries))
 		return -1;
@@ -995,7 +1452,7 @@ struct arm64_jit_data {
 
 struct bpf_prog *bpf_int_jit_compile(struct bpf_prog *prog)
 {
-	int image_size, prog_size, extable_size;
+	int image_size, prog_size, extable_size, extable_align, extable_offset;
 	struct bpf_prog *tmp, *orig_prog = prog;
 	struct bpf_binary_header *header;
 	struct arm64_jit_data *jit_data;
@@ -1039,34 +1496,43 @@ struct bpf_prog *bpf_int_jit_compile(struct bpf_prog *prog)
 	memset(&ctx, 0, sizeof(ctx));
 	ctx.prog = prog;
 
-	ctx.offset = kcalloc(prog->len + 1, sizeof(int), GFP_KERNEL);
+	ctx.offset = kvcalloc(prog->len + 1, sizeof(int), GFP_KERNEL);
 	if (ctx.offset == NULL) {
 		prog = orig_prog;
 		goto out_off;
 	}
 
-	/* 1. Initial fake pass to compute ctx->idx. */
+	ctx.fpb_offset = find_fpb_offset(prog);
 
-	/* Fake pass to fill in ctx->offset. */
-	if (build_body(&ctx, extra_pass)) {
+	/*
+	 * 1. Initial fake pass to compute ctx->idx and ctx->offset.
+	 *
+	 * BPF line info needs ctx->offset[i] to be the offset of
+	 * instruction[i] in jited image, so build prologue first.
+	 */
+	if (build_prologue(&ctx, was_classic)) {
 		prog = orig_prog;
 		goto out_off;
 	}
 
-	if (build_prologue(&ctx, was_classic)) {
+	if (build_body(&ctx, extra_pass)) {
 		prog = orig_prog;
 		goto out_off;
 	}
 
 	ctx.epilogue_offset = ctx.idx;
 	build_epilogue(&ctx);
+	build_plt(&ctx);
 
+	extable_align = __alignof__(struct exception_table_entry);
 	extable_size = prog->aux->num_exentries *
 		sizeof(struct exception_table_entry);
 
 	/* Now we know the actual image size. */
 	prog_size = sizeof(u32) * ctx.idx;
-	image_size = prog_size + extable_size;
+	/* also allocate space for plt target */
+	extable_offset = round_up(prog_size + PLT_TARGET_SIZE, extable_align);
+	image_size = extable_offset + extable_size;
 	header = bpf_jit_binary_alloc(image_size, &image_ptr,
 				      sizeof(u32), jit_fill_hole);
 	if (header == NULL) {
@@ -1078,7 +1544,7 @@ struct bpf_prog *bpf_int_jit_compile(struct bpf_prog *prog)
 
 	ctx.image = (__le32 *)image_ptr;
 	if (extable_size)
-		prog->aux->extable = (void *)image_ptr + prog_size;
+		prog->aux->extable = (void *)image_ptr + extable_offset;
 skip_init_ctx:
 	ctx.idx = 0;
 	ctx.exentry_idx = 0;
@@ -1092,9 +1558,10 @@ skip_init_ctx:
 	}
 
 	build_epilogue(&ctx);
+	build_plt(&ctx);
 
 	/* 3. Extra pass to validate JITed code. */
-	if (validate_code(&ctx)) {
+	if (validate_ctx(&ctx)) {
 		bpf_jit_binary_free(header);
 		prog = orig_prog;
 		goto out_off;
@@ -1113,6 +1580,7 @@ skip_init_ctx:
 			bpf_jit_binary_free(header);
 			prog->bpf_func = NULL;
 			prog->jited = 0;
+			prog->jited_len = 0;
 			goto out_off;
 		}
 		bpf_jit_binary_lock_ro(header);
@@ -1126,9 +1594,14 @@ skip_init_ctx:
 	prog->jited_len = prog_size;
 
 	if (!prog->is_func || extra_pass) {
+		int i;
+
+		/* offset[prog->len] is the size of program */
+		for (i = 0; i <= prog->len; i++)
+			ctx.offset[i] *= AARCH64_INSN_SIZE;
 		bpf_prog_fill_jited_linfo(prog, ctx.offset + 1);
 out_off:
-		kfree(ctx.offset);
+		kvfree(ctx.offset);
 		kfree(jit_data);
 		prog->aux->jit_data = NULL;
 	}
@@ -1139,20 +1612,615 @@ out:
 	return prog;
 }
 
+bool bpf_jit_supports_kfunc_call(void)
+{
+	return true;
+}
+
 u64 bpf_jit_alloc_exec_limit(void)
 {
-	return BPF_JIT_REGION_SIZE;
+	return VMALLOC_END - VMALLOC_START;
 }
 
 void *bpf_jit_alloc_exec(unsigned long size)
 {
-	return __vmalloc_node_range(size, PAGE_SIZE, BPF_JIT_REGION_START,
-				    BPF_JIT_REGION_END, GFP_KERNEL,
-				    PAGE_KERNEL, 0, NUMA_NO_NODE,
-				    __builtin_return_address(0));
+	/* Memory is intended to be executable, reset the pointer tag. */
+	return kasan_reset_tag(vmalloc(size));
 }
 
 void bpf_jit_free_exec(void *addr)
 {
 	return vfree(addr);
 }
+
+/* Indicate the JIT backend supports mixing bpf2bpf and tailcalls. */
+bool bpf_jit_supports_subprog_tailcalls(void)
+{
+	return true;
+}
+
+static void invoke_bpf_prog(struct jit_ctx *ctx, struct bpf_tramp_link *l,
+			    int args_off, int retval_off, int run_ctx_off,
+			    bool save_ret)
+{
+	__le32 *branch;
+	u64 enter_prog;
+	u64 exit_prog;
+	struct bpf_prog *p = l->link.prog;
+	int cookie_off = offsetof(struct bpf_tramp_run_ctx, bpf_cookie);
+
+	if (p->aux->sleepable) {
+		enter_prog = (u64)__bpf_prog_enter_sleepable;
+		exit_prog = (u64)__bpf_prog_exit_sleepable;
+	} else {
+		enter_prog = (u64)__bpf_prog_enter;
+		exit_prog = (u64)__bpf_prog_exit;
+	}
+
+	if (l->cookie == 0) {
+		/* if cookie is zero, one instruction is enough to store it */
+		emit(A64_STR64I(A64_ZR, A64_SP, run_ctx_off + cookie_off), ctx);
+	} else {
+		emit_a64_mov_i64(A64_R(10), l->cookie, ctx);
+		emit(A64_STR64I(A64_R(10), A64_SP, run_ctx_off + cookie_off),
+		     ctx);
+	}
+
+	/* save p to callee saved register x19 to avoid loading p with mov_i64
+	 * each time.
+	 */
+	emit_addr_mov_i64(A64_R(19), (const u64)p, ctx);
+
+	/* arg1: prog */
+	emit(A64_MOV(1, A64_R(0), A64_R(19)), ctx);
+	/* arg2: &run_ctx */
+	emit(A64_ADD_I(1, A64_R(1), A64_SP, run_ctx_off), ctx);
+
+	emit_call(enter_prog, ctx);
+
+	/* if (__bpf_prog_enter(prog) == 0)
+	 *         goto skip_exec_of_prog;
+	 */
+	branch = ctx->image + ctx->idx;
+	emit(A64_NOP, ctx);
+
+	/* save return value to callee saved register x20 */
+	emit(A64_MOV(1, A64_R(20), A64_R(0)), ctx);
+
+	emit(A64_ADD_I(1, A64_R(0), A64_SP, args_off), ctx);
+	if (!p->jited)
+		emit_addr_mov_i64(A64_R(1), (const u64)p->insnsi, ctx);
+
+	emit_call((const u64)p->bpf_func, ctx);
+
+	if (save_ret)
+		emit(A64_STR64I(A64_R(0), A64_SP, retval_off), ctx);
+
+	if (ctx->image) {
+		int offset = &ctx->image[ctx->idx] - branch;
+		*branch = cpu_to_le32(A64_CBZ(1, A64_R(0), offset));
+	}
+
+	/* arg1: prog */
+	emit(A64_MOV(1, A64_R(0), A64_R(19)), ctx);
+	/* arg2: start time */
+	emit(A64_MOV(1, A64_R(1), A64_R(20)), ctx);
+	/* arg3: &run_ctx */
+	emit(A64_ADD_I(1, A64_R(2), A64_SP, run_ctx_off), ctx);
+
+	emit_call(exit_prog, ctx);
+}
+
+static void invoke_bpf_mod_ret(struct jit_ctx *ctx, struct bpf_tramp_links *tl,
+			       int args_off, int retval_off, int run_ctx_off,
+			       __le32 **branches)
+{
+	int i;
+
+	/* The first fmod_ret program will receive a garbage return value.
+	 * Set this to 0 to avoid confusing the program.
+	 */
+	emit(A64_STR64I(A64_ZR, A64_SP, retval_off), ctx);
+	for (i = 0; i < tl->nr_links; i++) {
+		invoke_bpf_prog(ctx, tl->links[i], args_off, retval_off,
+				run_ctx_off, true);
+		/* if (*(u64 *)(sp + retval_off) !=  0)
+		 *	goto do_fexit;
+		 */
+		emit(A64_LDR64I(A64_R(10), A64_SP, retval_off), ctx);
+		/* Save the location of branch, and generate a nop.
+		 * This nop will be replaced with a cbnz later.
+		 */
+		branches[i] = ctx->image + ctx->idx;
+		emit(A64_NOP, ctx);
+	}
+}
+
+static void save_args(struct jit_ctx *ctx, int args_off, int nargs)
+{
+	int i;
+
+	for (i = 0; i < nargs; i++) {
+		emit(A64_STR64I(i, A64_SP, args_off), ctx);
+		args_off += 8;
+	}
+}
+
+static void restore_args(struct jit_ctx *ctx, int args_off, int nargs)
+{
+	int i;
+
+	for (i = 0; i < nargs; i++) {
+		emit(A64_LDR64I(i, A64_SP, args_off), ctx);
+		args_off += 8;
+	}
+}
+
+/* Based on the x86's implementation of arch_prepare_bpf_trampoline().
+ *
+ * bpf prog and function entry before bpf trampoline hooked:
+ *   mov x9, lr
+ *   nop
+ *
+ * bpf prog and function entry after bpf trampoline hooked:
+ *   mov x9, lr
+ *   bl  <bpf_trampoline or plt>
+ *
+ */
+static int prepare_trampoline(struct jit_ctx *ctx, struct bpf_tramp_image *im,
+			      struct bpf_tramp_links *tlinks, void *orig_call,
+			      int nargs, u32 flags)
+{
+	int i;
+	int stack_size;
+	int retaddr_off;
+	int regs_off;
+	int retval_off;
+	int args_off;
+	int nargs_off;
+	int ip_off;
+	int run_ctx_off;
+	struct bpf_tramp_links *fentry = &tlinks[BPF_TRAMP_FENTRY];
+	struct bpf_tramp_links *fexit = &tlinks[BPF_TRAMP_FEXIT];
+	struct bpf_tramp_links *fmod_ret = &tlinks[BPF_TRAMP_MODIFY_RETURN];
+	bool save_ret;
+	__le32 **branches = NULL;
+
+	/* trampoline stack layout:
+	 *                  [ parent ip         ]
+	 *                  [ FP                ]
+	 * SP + retaddr_off [ self ip           ]
+	 *                  [ FP                ]
+	 *
+	 *                  [ padding           ] align SP to multiples of 16
+	 *
+	 *                  [ x20               ] callee saved reg x20
+	 * SP + regs_off    [ x19               ] callee saved reg x19
+	 *
+	 * SP + retval_off  [ return value      ] BPF_TRAMP_F_CALL_ORIG or
+	 *                                        BPF_TRAMP_F_RET_FENTRY_RET
+	 *
+	 *                  [ argN              ]
+	 *                  [ ...               ]
+	 * SP + args_off    [ arg1              ]
+	 *
+	 * SP + nargs_off   [ args count        ]
+	 *
+	 * SP + ip_off      [ traced function   ] BPF_TRAMP_F_IP_ARG flag
+	 *
+	 * SP + run_ctx_off [ bpf_tramp_run_ctx ]
+	 */
+
+	stack_size = 0;
+	run_ctx_off = stack_size;
+	/* room for bpf_tramp_run_ctx */
+	stack_size += round_up(sizeof(struct bpf_tramp_run_ctx), 8);
+
+	ip_off = stack_size;
+	/* room for IP address argument */
+	if (flags & BPF_TRAMP_F_IP_ARG)
+		stack_size += 8;
+
+	nargs_off = stack_size;
+	/* room for args count */
+	stack_size += 8;
+
+	args_off = stack_size;
+	/* room for args */
+	stack_size += nargs * 8;
+
+	/* room for return value */
+	retval_off = stack_size;
+	save_ret = flags & (BPF_TRAMP_F_CALL_ORIG | BPF_TRAMP_F_RET_FENTRY_RET);
+	if (save_ret)
+		stack_size += 8;
+
+	/* room for callee saved registers, currently x19 and x20 are used */
+	regs_off = stack_size;
+	stack_size += 16;
+
+	/* round up to multiples of 16 to avoid SPAlignmentFault */
+	stack_size = round_up(stack_size, 16);
+
+	/* return address locates above FP */
+	retaddr_off = stack_size + 8;
+
+	/* bpf trampoline may be invoked by 3 instruction types:
+	 * 1. bl, attached to bpf prog or kernel function via short jump
+	 * 2. br, attached to bpf prog or kernel function via long jump
+	 * 3. blr, working as a function pointer, used by struct_ops.
+	 * So BTI_JC should used here to support both br and blr.
+	 */
+	emit_bti(A64_BTI_JC, ctx);
+
+	/* frame for parent function */
+	emit(A64_PUSH(A64_FP, A64_R(9), A64_SP), ctx);
+	emit(A64_MOV(1, A64_FP, A64_SP), ctx);
+
+	/* frame for patched function */
+	emit(A64_PUSH(A64_FP, A64_LR, A64_SP), ctx);
+	emit(A64_MOV(1, A64_FP, A64_SP), ctx);
+
+	/* allocate stack space */
+	emit(A64_SUB_I(1, A64_SP, A64_SP, stack_size), ctx);
+
+	if (flags & BPF_TRAMP_F_IP_ARG) {
+		/* save ip address of the traced function */
+		emit_addr_mov_i64(A64_R(10), (const u64)orig_call, ctx);
+		emit(A64_STR64I(A64_R(10), A64_SP, ip_off), ctx);
+	}
+
+	/* save args count*/
+	emit(A64_MOVZ(1, A64_R(10), nargs, 0), ctx);
+	emit(A64_STR64I(A64_R(10), A64_SP, nargs_off), ctx);
+
+	/* save args */
+	save_args(ctx, args_off, nargs);
+
+	/* save callee saved registers */
+	emit(A64_STR64I(A64_R(19), A64_SP, regs_off), ctx);
+	emit(A64_STR64I(A64_R(20), A64_SP, regs_off + 8), ctx);
+
+	if (flags & BPF_TRAMP_F_CALL_ORIG) {
+		emit_addr_mov_i64(A64_R(0), (const u64)im, ctx);
+		emit_call((const u64)__bpf_tramp_enter, ctx);
+	}
+
+	for (i = 0; i < fentry->nr_links; i++)
+		invoke_bpf_prog(ctx, fentry->links[i], args_off,
+				retval_off, run_ctx_off,
+				flags & BPF_TRAMP_F_RET_FENTRY_RET);
+
+	if (fmod_ret->nr_links) {
+		branches = kcalloc(fmod_ret->nr_links, sizeof(__le32 *),
+				   GFP_KERNEL);
+		if (!branches)
+			return -ENOMEM;
+
+		invoke_bpf_mod_ret(ctx, fmod_ret, args_off, retval_off,
+				   run_ctx_off, branches);
+	}
+
+	if (flags & BPF_TRAMP_F_CALL_ORIG) {
+		restore_args(ctx, args_off, nargs);
+		/* call original func */
+		emit(A64_LDR64I(A64_R(10), A64_SP, retaddr_off), ctx);
+		emit(A64_BLR(A64_R(10)), ctx);
+		/* store return value */
+		emit(A64_STR64I(A64_R(0), A64_SP, retval_off), ctx);
+		/* reserve a nop for bpf_tramp_image_put */
+		im->ip_after_call = ctx->image + ctx->idx;
+		emit(A64_NOP, ctx);
+	}
+
+	/* update the branches saved in invoke_bpf_mod_ret with cbnz */
+	for (i = 0; i < fmod_ret->nr_links && ctx->image != NULL; i++) {
+		int offset = &ctx->image[ctx->idx] - branches[i];
+		*branches[i] = cpu_to_le32(A64_CBNZ(1, A64_R(10), offset));
+	}
+
+	for (i = 0; i < fexit->nr_links; i++)
+		invoke_bpf_prog(ctx, fexit->links[i], args_off, retval_off,
+				run_ctx_off, false);
+
+	if (flags & BPF_TRAMP_F_CALL_ORIG) {
+		im->ip_epilogue = ctx->image + ctx->idx;
+		emit_addr_mov_i64(A64_R(0), (const u64)im, ctx);
+		emit_call((const u64)__bpf_tramp_exit, ctx);
+	}
+
+	if (flags & BPF_TRAMP_F_RESTORE_REGS)
+		restore_args(ctx, args_off, nargs);
+
+	/* restore callee saved register x19 and x20 */
+	emit(A64_LDR64I(A64_R(19), A64_SP, regs_off), ctx);
+	emit(A64_LDR64I(A64_R(20), A64_SP, regs_off + 8), ctx);
+
+	if (save_ret)
+		emit(A64_LDR64I(A64_R(0), A64_SP, retval_off), ctx);
+
+	/* reset SP  */
+	emit(A64_MOV(1, A64_SP, A64_FP), ctx);
+
+	/* pop frames  */
+	emit(A64_POP(A64_FP, A64_LR, A64_SP), ctx);
+	emit(A64_POP(A64_FP, A64_R(9), A64_SP), ctx);
+
+	if (flags & BPF_TRAMP_F_SKIP_FRAME) {
+		/* skip patched function, return to parent */
+		emit(A64_MOV(1, A64_LR, A64_R(9)), ctx);
+		emit(A64_RET(A64_R(9)), ctx);
+	} else {
+		/* return to patched function */
+		emit(A64_MOV(1, A64_R(10), A64_LR), ctx);
+		emit(A64_MOV(1, A64_LR, A64_R(9)), ctx);
+		emit(A64_RET(A64_R(10)), ctx);
+	}
+
+	if (ctx->image)
+		bpf_flush_icache(ctx->image, ctx->image + ctx->idx);
+
+	kfree(branches);
+
+	return ctx->idx;
+}
+
+int arch_prepare_bpf_trampoline(struct bpf_tramp_image *im, void *image,
+				void *image_end, const struct btf_func_model *m,
+				u32 flags, struct bpf_tramp_links *tlinks,
+				void *orig_call)
+{
+	int i, ret;
+	int nargs = m->nr_args;
+	int max_insns = ((long)image_end - (long)image) / AARCH64_INSN_SIZE;
+	struct jit_ctx ctx = {
+		.image = NULL,
+		.idx = 0,
+	};
+
+	/* the first 8 arguments are passed by registers */
+	if (nargs > 8)
+		return -ENOTSUPP;
+
+	/* don't support struct argument */
+	for (i = 0; i < MAX_BPF_FUNC_ARGS; i++) {
+		if (m->arg_flags[i] & BTF_FMODEL_STRUCT_ARG)
+			return -ENOTSUPP;
+	}
+
+	ret = prepare_trampoline(&ctx, im, tlinks, orig_call, nargs, flags);
+	if (ret < 0)
+		return ret;
+
+	if (ret > max_insns)
+		return -EFBIG;
+
+	ctx.image = image;
+	ctx.idx = 0;
+
+	jit_fill_hole(image, (unsigned int)(image_end - image));
+	ret = prepare_trampoline(&ctx, im, tlinks, orig_call, nargs, flags);
+
+	if (ret > 0 && validate_code(&ctx) < 0)
+		ret = -EINVAL;
+
+	if (ret > 0)
+		ret *= AARCH64_INSN_SIZE;
+
+	return ret;
+}
+
+static bool is_long_jump(void *ip, void *target)
+{
+	long offset;
+
+	/* NULL target means this is a NOP */
+	if (!target)
+		return false;
+
+	offset = (long)target - (long)ip;
+	return offset < -SZ_128M || offset >= SZ_128M;
+}
+
+static int gen_branch_or_nop(enum aarch64_insn_branch_type type, void *ip,
+			     void *addr, void *plt, u32 *insn)
+{
+	void *target;
+
+	if (!addr) {
+		*insn = aarch64_insn_gen_nop();
+		return 0;
+	}
+
+	if (is_long_jump(ip, addr))
+		target = plt;
+	else
+		target = addr;
+
+	*insn = aarch64_insn_gen_branch_imm((unsigned long)ip,
+					    (unsigned long)target,
+					    type);
+
+	return *insn != AARCH64_BREAK_FAULT ? 0 : -EFAULT;
+}
+
+/* Replace the branch instruction from @ip to @old_addr in a bpf prog or a bpf
+ * trampoline with the branch instruction from @ip to @new_addr. If @old_addr
+ * or @new_addr is NULL, the old or new instruction is NOP.
+ *
+ * When @ip is the bpf prog entry, a bpf trampoline is being attached or
+ * detached. Since bpf trampoline and bpf prog are allocated separately with
+ * vmalloc, the address distance may exceed 128MB, the maximum branch range.
+ * So long jump should be handled.
+ *
+ * When a bpf prog is constructed, a plt pointing to empty trampoline
+ * dummy_tramp is placed at the end:
+ *
+ *      bpf_prog:
+ *              mov x9, lr
+ *              nop // patchsite
+ *              ...
+ *              ret
+ *
+ *      plt:
+ *              ldr x10, target
+ *              br x10
+ *      target:
+ *              .quad dummy_tramp // plt target
+ *
+ * This is also the state when no trampoline is attached.
+ *
+ * When a short-jump bpf trampoline is attached, the patchsite is patched
+ * to a bl instruction to the trampoline directly:
+ *
+ *      bpf_prog:
+ *              mov x9, lr
+ *              bl <short-jump bpf trampoline address> // patchsite
+ *              ...
+ *              ret
+ *
+ *      plt:
+ *              ldr x10, target
+ *              br x10
+ *      target:
+ *              .quad dummy_tramp // plt target
+ *
+ * When a long-jump bpf trampoline is attached, the plt target is filled with
+ * the trampoline address and the patchsite is patched to a bl instruction to
+ * the plt:
+ *
+ *      bpf_prog:
+ *              mov x9, lr
+ *              bl plt // patchsite
+ *              ...
+ *              ret
+ *
+ *      plt:
+ *              ldr x10, target
+ *              br x10
+ *      target:
+ *              .quad <long-jump bpf trampoline address> // plt target
+ *
+ * The dummy_tramp is used to prevent another CPU from jumping to unknown
+ * locations during the patching process, making the patching process easier.
+ */
+int bpf_arch_text_poke(void *ip, enum bpf_text_poke_type poke_type,
+		       void *old_addr, void *new_addr)
+{
+	int ret;
+	u32 old_insn;
+	u32 new_insn;
+	u32 replaced;
+	struct bpf_plt *plt = NULL;
+	unsigned long size = 0UL;
+	unsigned long offset = ~0UL;
+	enum aarch64_insn_branch_type branch_type;
+	char namebuf[KSYM_NAME_LEN];
+	void *image = NULL;
+	u64 plt_target = 0ULL;
+	bool poking_bpf_entry;
+
+	if (!__bpf_address_lookup((unsigned long)ip, &size, &offset, namebuf))
+		/* Only poking bpf text is supported. Since kernel function
+		 * entry is set up by ftrace, we reply on ftrace to poke kernel
+		 * functions.
+		 */
+		return -ENOTSUPP;
+
+	image = ip - offset;
+	/* zero offset means we're poking bpf prog entry */
+	poking_bpf_entry = (offset == 0UL);
+
+	/* bpf prog entry, find plt and the real patchsite */
+	if (poking_bpf_entry) {
+		/* plt locates at the end of bpf prog */
+		plt = image + size - PLT_TARGET_OFFSET;
+
+		/* skip to the nop instruction in bpf prog entry:
+		 * bti c // if BTI enabled
+		 * mov x9, x30
+		 * nop
+		 */
+		ip = image + POKE_OFFSET * AARCH64_INSN_SIZE;
+	}
+
+	/* long jump is only possible at bpf prog entry */
+	if (WARN_ON((is_long_jump(ip, new_addr) || is_long_jump(ip, old_addr)) &&
+		    !poking_bpf_entry))
+		return -EINVAL;
+
+	if (poke_type == BPF_MOD_CALL)
+		branch_type = AARCH64_INSN_BRANCH_LINK;
+	else
+		branch_type = AARCH64_INSN_BRANCH_NOLINK;
+
+	if (gen_branch_or_nop(branch_type, ip, old_addr, plt, &old_insn) < 0)
+		return -EFAULT;
+
+	if (gen_branch_or_nop(branch_type, ip, new_addr, plt, &new_insn) < 0)
+		return -EFAULT;
+
+	if (is_long_jump(ip, new_addr))
+		plt_target = (u64)new_addr;
+	else if (is_long_jump(ip, old_addr))
+		/* if the old target is a long jump and the new target is not,
+		 * restore the plt target to dummy_tramp, so there is always a
+		 * legal and harmless address stored in plt target, and we'll
+		 * never jump from plt to an unknown place.
+		 */
+		plt_target = (u64)&dummy_tramp;
+
+	if (plt_target) {
+		/* non-zero plt_target indicates we're patching a bpf prog,
+		 * which is read only.
+		 */
+		if (set_memory_rw(PAGE_MASK & ((uintptr_t)&plt->target), 1))
+			return -EFAULT;
+		WRITE_ONCE(plt->target, plt_target);
+		set_memory_ro(PAGE_MASK & ((uintptr_t)&plt->target), 1);
+		/* since plt target points to either the new trampoline
+		 * or dummy_tramp, even if another CPU reads the old plt
+		 * target value before fetching the bl instruction to plt,
+		 * it will be brought back by dummy_tramp, so no barrier is
+		 * required here.
+		 */
+	}
+
+	/* if the old target and the new target are both long jumps, no
+	 * patching is required
+	 */
+	if (old_insn == new_insn)
+		return 0;
+
+	mutex_lock(&text_mutex);
+	if (aarch64_insn_read(ip, &replaced)) {
+		ret = -EFAULT;
+		goto out;
+	}
+
+	if (replaced != old_insn) {
+		ret = -EFAULT;
+		goto out;
+	}
+
+	/* We call aarch64_insn_patch_text_nosync() to replace instruction
+	 * atomically, so no other CPUs will fetch a half-new and half-old
+	 * instruction. But there is chance that another CPU executes the
+	 * old instruction after the patching operation finishes (e.g.,
+	 * pipeline not flushed, or icache not synchronized yet).
+	 *
+	 * 1. when a new trampoline is attached, it is not a problem for
+	 *    different CPUs to jump to different trampolines temporarily.
+	 *
+	 * 2. when an old trampoline is freed, we should wait for all other
+	 *    CPUs to exit the trampoline and make sure the trampoline is no
+	 *    longer reachable, since bpf_tramp_image_put() function already
+	 *    uses percpu_ref and task-based rcu to do the sync, no need to call
+	 *    the sync version here, see bpf_tramp_image_put() for details.
+	 */
+	ret = aarch64_insn_patch_text_nosync(ip, new_insn);
+out:
+	mutex_unlock(&text_mutex);
+
+	return ret;
+}
diff --git a/arch/arm64/tools/Makefile b/arch/arm64/tools/Makefile
index 932b4fe5c768..07a93ab21a62 100644
--- a/arch/arm64/tools/Makefile
+++ b/arch/arm64/tools/Makefile
@@ -3,20 +3,22 @@
 gen := arch/$(ARCH)/include/generated
 kapi := $(gen)/asm
 
-kapi-hdrs-y := $(kapi)/cpucaps.h
+kapi-hdrs-y := $(kapi)/cpucaps.h $(kapi)/sysreg-defs.h
 
-targets += $(addprefix ../../../,$(gen-y) $(kapi-hdrs-y))
+targets += $(addprefix ../../../, $(kapi-hdrs-y))
 
 PHONY += kapi
 
-kapi:   $(kapi-hdrs-y) $(gen-y)
-
-# Create output directory if not already present
-_dummy := $(shell [ -d '$(kapi)' ] || mkdir -p '$(kapi)')
+kapi:   $(kapi-hdrs-y)
 
 quiet_cmd_gen_cpucaps = GEN     $@
-      cmd_gen_cpucaps = mkdir -p $(dir $@) && \
-                     $(AWK) -f $(filter-out $(PHONY),$^) > $@
+      cmd_gen_cpucaps = mkdir -p $(dir $@); $(AWK) -f $(real-prereqs) > $@
+
+quiet_cmd_gen_sysreg = GEN     $@
+      cmd_gen_sysreg = mkdir -p $(dir $@); $(AWK) -f $(real-prereqs) > $@
 
 $(kapi)/cpucaps.h: $(src)/gen-cpucaps.awk $(src)/cpucaps FORCE
 	$(call if_changed,gen_cpucaps)
+
+$(kapi)/sysreg-defs.h: $(src)/gen-sysreg.awk $(src)/sysreg FORCE
+	$(call if_changed,gen_sysreg)
diff --git a/arch/arm64/tools/cpucaps b/arch/arm64/tools/cpucaps
index 870c39537dd0..f1c0347ec31a 100644
--- a/arch/arm64/tools/cpucaps
+++ b/arch/arm64/tools/cpucaps
@@ -2,12 +2,15 @@
 #
 # Internal CPU capabilities constants, keep this list sorted
 
+ALWAYS_BOOT
+ALWAYS_SYSTEM
 BTI
 # Unreliable: use system_supports_32bit_el0() instead.
 HAS_32BIT_EL0_DO_NOT_USE
 HAS_32BIT_EL1
 HAS_ADDRESS_AUTH
-HAS_ADDRESS_AUTH_ARCH
+HAS_ADDRESS_AUTH_ARCH_QARMA3
+HAS_ADDRESS_AUTH_ARCH_QARMA5
 HAS_ADDRESS_AUTH_IMP_DEF
 HAS_AMU_EXTN
 HAS_ARMv8_4_TTL
@@ -21,7 +24,8 @@ HAS_E0PD
 HAS_ECV
 HAS_EPAN
 HAS_GENERIC_AUTH
-HAS_GENERIC_AUTH_ARCH
+HAS_GENERIC_AUTH_ARCH_QARMA3
+HAS_GENERIC_AUTH_ARCH_QARMA5
 HAS_GENERIC_AUTH_IMP_DEF
 HAS_IRQ_PRIO_MASKING
 HAS_LDAPR
@@ -34,16 +38,21 @@ HAS_RNG
 HAS_SB
 HAS_STAGE2_FWB
 HAS_SYSREG_GIC_CPUIF
+HAS_TIDCP1
 HAS_TLB_RANGE
 HAS_VIRT_HOST_EXTN
+HAS_WFXT
 HW_DBM
 KVM_PROTECTED_MODE
 MISMATCHED_CACHE_TYPE
 MTE
 MTE_ASYMM
+SME
+SME_FA64
 SPECTRE_V2
 SPECTRE_V3A
 SPECTRE_V4
+SPECTRE_BHB
 SSBS
 SVE
 UNMAP_KERNEL_AT_EL0
@@ -55,6 +64,13 @@ WORKAROUND_1418040
 WORKAROUND_1463225
 WORKAROUND_1508412
 WORKAROUND_1542419
+WORKAROUND_1742098
+WORKAROUND_1902691
+WORKAROUND_2038923
+WORKAROUND_2064142
+WORKAROUND_2077057
+WORKAROUND_2457168
+WORKAROUND_2658417
 WORKAROUND_TRBE_OVERWRITE_FILL_MODE
 WORKAROUND_TSB_FLUSH_FAILURE
 WORKAROUND_TRBE_WRITE_OUT_OF_RANGE
diff --git a/arch/arm64/tools/gen-sysreg.awk b/arch/arm64/tools/gen-sysreg.awk
new file mode 100755
index 000000000000..db461921d256
--- /dev/null
+++ b/arch/arm64/tools/gen-sysreg.awk
@@ -0,0 +1,268 @@
+#!/bin/awk -f
+# SPDX-License-Identifier: GPL-2.0
+# gen-sysreg.awk: arm64 sysreg header generator
+#
+# Usage: awk -f gen-sysreg.awk sysregs.txt
+
+# Log an error and terminate
+function fatal(msg) {
+	print "Error at " NR ": " msg > "/dev/stderr"
+	exit 1
+}
+
+# Sanity check that the start or end of a block makes sense at this point in
+# the file. If not, produce an error and terminate.
+#
+# @this - the $Block or $EndBlock
+# @prev - the only valid block to already be in (value of @block)
+# @new - the new value of @block
+function change_block(this, prev, new) {
+	if (block != prev)
+		fatal("unexpected " this " (inside " block ")")
+
+	block = new
+}
+
+# Sanity check the number of records for a field makes sense. If not, produce
+# an error and terminate.
+function expect_fields(nf) {
+	if (NF != nf)
+		fatal(NF " fields found where " nf " expected")
+}
+
+# Print a CPP macro definition, padded with spaces so that the macro bodies
+# line up in a column
+function define(name, val) {
+	printf "%-48s%s\n", "#define " name, val
+}
+
+# Print standard BITMASK/SHIFT/WIDTH CPP definitions for a field
+function define_field(reg, field, msb, lsb) {
+	define(reg "_" field, "GENMASK(" msb ", " lsb ")")
+	define(reg "_" field "_MASK", "GENMASK(" msb ", " lsb ")")
+	define(reg "_" field "_SHIFT", lsb)
+	define(reg "_" field "_WIDTH", msb - lsb + 1)
+}
+
+# Parse a "<msb>[:<lsb>]" string into the global variables @msb and @lsb
+function parse_bitdef(reg, field, bitdef, _bits)
+{
+	if (bitdef ~ /^[0-9]+$/) {
+		msb = bitdef
+		lsb = bitdef
+	} else if (split(bitdef, _bits, ":") == 2) {
+		msb = _bits[1]
+		lsb = _bits[2]
+	} else {
+		fatal("invalid bit-range definition '" bitdef "'")
+	}
+
+
+	if (msb != next_bit)
+		fatal(reg "." field " starts at " msb " not " next_bit)
+	if (63 < msb || msb < 0)
+		fatal(reg "." field " invalid high bit in '" bitdef "'")
+	if (63 < lsb || lsb < 0)
+		fatal(reg "." field " invalid low bit in '" bitdef "'")
+	if (msb < lsb)
+		fatal(reg "." field " invalid bit-range '" bitdef "'")
+	if (low > high)
+		fatal(reg "." field " has invalid range " high "-" low)
+
+	next_bit = lsb - 1
+}
+
+BEGIN {
+	print "#ifndef __ASM_SYSREG_DEFS_H"
+	print "#define __ASM_SYSREG_DEFS_H"
+	print ""
+	print "/* Generated file - do not edit */"
+	print ""
+
+	block = "None"
+}
+
+END {
+	print "#endif /* __ASM_SYSREG_DEFS_H */"
+}
+
+# skip blank lines and comment lines
+/^$/ { next }
+/^[\t ]*#/ { next }
+
+/^SysregFields/ {
+	change_block("SysregFields", "None", "SysregFields")
+	expect_fields(2)
+
+	reg = $2
+
+	res0 = "UL(0)"
+	res1 = "UL(0)"
+
+	next_bit = 63
+
+	next
+}
+
+/^EndSysregFields/ {
+	if (next_bit > 0)
+		fatal("Unspecified bits in " reg)
+
+	change_block("EndSysregFields", "SysregFields", "None")
+
+	define(reg "_RES0", "(" res0 ")")
+	define(reg "_RES1", "(" res1 ")")
+	print ""
+
+	reg = null
+	res0 = null
+	res1 = null
+
+	next
+}
+
+/^Sysreg/ {
+	change_block("Sysreg", "None", "Sysreg")
+	expect_fields(7)
+
+	reg = $2
+	op0 = $3
+	op1 = $4
+	crn = $5
+	crm = $6
+	op2 = $7
+
+	res0 = "UL(0)"
+	res1 = "UL(0)"
+
+	define("REG_" reg, "S" op0 "_" op1 "_C" crn "_C" crm "_" op2)
+	define("SYS_" reg, "sys_reg(" op0 ", " op1 ", " crn ", " crm ", " op2 ")")
+
+	define("SYS_" reg "_Op0", op0)
+	define("SYS_" reg "_Op1", op1)
+	define("SYS_" reg "_CRn", crn)
+	define("SYS_" reg "_CRm", crm)
+	define("SYS_" reg "_Op2", op2)
+
+	print ""
+
+	next_bit = 63
+
+	next
+}
+
+/^EndSysreg/ {
+	if (next_bit > 0)
+		fatal("Unspecified bits in " reg)
+
+	change_block("EndSysreg", "Sysreg", "None")
+
+	if (res0 != null)
+		define(reg "_RES0", "(" res0 ")")
+	if (res1 != null)
+		define(reg "_RES1", "(" res1 ")")
+	if (res0 != null || res1 != null)
+		print ""
+
+	reg = null
+	op0 = null
+	op1 = null
+	crn = null
+	crm = null
+	op2 = null
+	res0 = null
+	res1 = null
+
+	next
+}
+
+# Currently this is effectivey a comment, in future we may want to emit
+# defines for the fields.
+/^Fields/ && (block == "Sysreg") {
+	expect_fields(2)
+
+	if (next_bit != 63)
+		fatal("Some fields already defined for " reg)
+
+	print "/* For " reg " fields see " $2 " */"
+	print ""
+
+        next_bit = 0
+	res0 = null
+	res1 = null
+
+	next
+}
+
+
+/^Res0/ && (block == "Sysreg" || block == "SysregFields") {
+	expect_fields(2)
+	parse_bitdef(reg, "RES0", $2)
+	field = "RES0_" msb "_" lsb
+
+	res0 = res0 " | GENMASK_ULL(" msb ", " lsb ")"
+
+	next
+}
+
+/^Res1/ && (block == "Sysreg" || block == "SysregFields") {
+	expect_fields(2)
+	parse_bitdef(reg, "RES1", $2)
+	field = "RES1_" msb "_" lsb
+
+	res1 = res1 " | GENMASK_ULL(" msb ", " lsb ")"
+
+	next
+}
+
+/^Field/ && (block == "Sysreg" || block == "SysregFields") {
+	expect_fields(3)
+	field = $3
+	parse_bitdef(reg, field, $2)
+
+	define_field(reg, field, msb, lsb)
+	print ""
+
+	next
+}
+
+/^Raz/ && (block == "Sysreg" || block == "SysregFields") {
+	expect_fields(2)
+	parse_bitdef(reg, field, $2)
+
+	next
+}
+
+/^Enum/ {
+	change_block("Enum", "Sysreg", "Enum")
+	expect_fields(3)
+	field = $3
+	parse_bitdef(reg, field, $2)
+
+	define_field(reg, field, msb, lsb)
+
+	next
+}
+
+/^EndEnum/ {
+	change_block("EndEnum", "Enum", "Sysreg")
+	field = null
+	msb = null
+	lsb = null
+	print ""
+	next
+}
+
+/0b[01]+/ && block == "Enum" {
+	expect_fields(2)
+	val = $1
+	name = $2
+
+	define(reg "_" field "_" name, "UL(" val ")")
+	next
+}
+
+# Any lines not handled by previous rules are unexpected
+{
+	fatal("unhandled statement")
+}
diff --git a/arch/arm64/tools/sysreg b/arch/arm64/tools/sysreg
new file mode 100644
index 000000000000..384757a7eda9
--- /dev/null
+++ b/arch/arm64/tools/sysreg
@@ -0,0 +1,1080 @@
+# SPDX-License-Identifier: GPL-2.0-only
+#
+# System register metadata
+
+# Each System register is described by a Sysreg block:
+
+# Sysreg 	<name>	<op0> 	<op1>	<crn>	<crm>	<op2>
+# <field>
+# ...
+# EndSysreg
+
+# Within a Sysreg block, each field can be described as one of:
+
+# Res0	<msb>[:<lsb>]
+
+# Res1	<msb>[:<lsb>]
+
+# Field	<msb>[:<lsb>]	<name>
+
+# Enum	<msb>[:<lsb>]	<name>
+#	<enumval>	<enumname>
+#	...
+# EndEnum
+
+# Alternatively if multiple registers share the same layout then
+# a SysregFields block can be used to describe the shared layout
+
+# SysregFields	<fieldsname>
+# <field>
+# ...
+# EndSysregFields
+
+# and referenced from within the Sysreg:
+
+# Sysreg 	<name>	<op0> 	<op1>	<crn>	<crm>	<op2>
+# Fields	<fieldsname>
+# EndSysreg
+
+# For ID registers we adopt a few conventions for translating the
+# language in the ARM into defines:
+#
+# NI  - Not implemented
+# IMP - Implemented
+#
+# In general it is recommended that new enumeration items be named for the
+# feature that introduces them (eg, FEAT_LS64_ACCDATA introduces enumeration
+# item ACCDATA) though it may be more taseful to do something else.
+
+Sysreg	ID_AA64PFR0_EL1	3	0	0	4	0
+Enum	63:60	CSV3
+	0b0000	NI
+	0b0001	IMP
+EndEnum
+Enum	59:56	CSV2
+	0b0000	NI
+	0b0001	IMP
+	0b0010	CSV2_2
+	0b0011	CSV2_3
+EndEnum
+Enum	55:52	RME
+	0b0000	NI
+	0b0001	IMP
+EndEnum
+Enum	51:48	DIT
+	0b0000	NI
+	0b0001	IMP
+EndEnum
+Enum	47:44	AMU
+	0b0000	NI
+	0b0001	IMP
+	0b0010	V1P1
+EndEnum
+Enum	43:40	MPAM
+	0b0000	0
+	0b0001	1
+EndEnum
+Enum	39:36	SEL2
+	0b0000	NI
+	0b0001	IMP
+EndEnum
+Enum	35:32	SVE
+	0b0000	NI
+	0b0001	IMP
+EndEnum
+Enum	31:28	RAS
+	0b0000	NI
+	0b0001	IMP
+	0b0010	V1P1
+EndEnum
+Enum	27:24	GIC
+	0b0000	NI
+	0b0001	IMP
+	0b0010	V4P1
+EndEnum
+Enum	23:20	AdvSIMD
+	0b0000	IMP
+	0b0001	FP16
+	0b1111	NI
+EndEnum
+Enum	19:16	FP
+	0b0000	IMP
+	0b0001	FP16
+	0b1111	NI
+EndEnum
+Enum	15:12	EL3
+	0b0000	NI
+	0b0001	IMP
+	0b0010	AARCH32
+EndEnum
+Enum	11:8	EL2
+	0b0000	NI
+	0b0001	IMP
+	0b0010	AARCH32
+EndEnum
+Enum	7:4	EL1
+	0b0001	IMP
+	0b0010	AARCH32
+EndEnum
+Enum	3:0	EL0
+	0b0001	IMP
+	0b0010	AARCH32
+EndEnum
+EndSysreg
+
+Sysreg	ID_AA64PFR1_EL1	3	0	0	4	1
+Res0	63:40
+Enum	39:36	NMI
+	0b0000	NI
+	0b0001	IMP
+EndEnum
+Enum	35:32	CSV2_frac
+	0b0000	NI
+	0b0001	CSV2_1p1
+	0b0010	CSV2_1p2
+EndEnum
+Enum	31:28	RNDR_trap
+	0b0000	NI
+	0b0001	IMP
+EndEnum
+Enum	27:24	SME
+	0b0000	NI
+	0b0001	IMP
+EndEnum
+Res0	23:20
+Enum	19:16	MPAM_frac
+	0b0000	MINOR_0
+	0b0001	MINOR_1
+EndEnum
+Enum	15:12	RAS_frac
+	0b0000	NI
+	0b0001	RASv1p1
+EndEnum
+Enum	11:8	MTE
+	0b0000	NI
+	0b0001	IMP
+	0b0010	MTE2
+	0b0011	MTE3
+EndEnum
+Enum	7:4	SSBS
+	0b0000	NI
+	0b0001	IMP
+	0b0010	SSBS2
+EndEnum
+Enum	3:0	BT
+	0b0000	NI
+	0b0001	IMP
+EndEnum
+EndSysreg
+
+Sysreg	ID_AA64ZFR0_EL1	3	0	0	4	4
+Res0	63:60
+Enum	59:56	F64MM
+	0b0000	NI
+	0b0001	IMP
+EndEnum
+Enum	55:52	F32MM
+	0b0000	NI
+	0b0001	IMP
+EndEnum
+Res0	51:48
+Enum	47:44	I8MM
+	0b0000	NI
+	0b0001	IMP
+EndEnum
+Enum	43:40	SM4
+	0b0000	NI
+	0b0001	IMP
+EndEnum
+Res0	39:36
+Enum	35:32	SHA3
+	0b0000	NI
+	0b0001	IMP
+EndEnum
+Res0	31:24
+Enum	23:20	BF16
+	0b0000	NI
+	0b0001	IMP
+	0b0010	EBF16
+EndEnum
+Enum	19:16	BitPerm
+	0b0000	NI
+	0b0001	IMP
+EndEnum
+Res0	15:8
+Enum	7:4	AES
+	0b0000	NI
+	0b0001	IMP
+	0b0010	PMULL128
+EndEnum
+Enum	3:0	SVEver
+	0b0000	IMP
+	0b0001	SVE2
+EndEnum
+EndSysreg
+
+Sysreg	ID_AA64SMFR0_EL1	3	0	0	4	5
+Enum	63	FA64
+	0b0	NI
+	0b1	IMP
+EndEnum
+Res0	62:60
+Enum	59:56	SMEver
+	0b0000	IMP
+EndEnum
+Enum	55:52	I16I64
+	0b0000	NI
+	0b1111	IMP
+EndEnum
+Res0	51:49
+Enum	48	F64F64
+	0b0	NI
+	0b1	IMP
+EndEnum
+Res0	47:40
+Enum	39:36	I8I32
+	0b0000	NI
+	0b1111	IMP
+EndEnum
+Enum	35	F16F32
+	0b0	NI
+	0b1	IMP
+EndEnum
+Enum	34	B16F32
+	0b0	NI
+	0b1	IMP
+EndEnum
+Res0	33
+Enum	32	F32F32
+	0b0	NI
+	0b1	IMP
+EndEnum
+Res0	31:0
+EndSysreg
+
+Sysreg	ID_AA64DFR0_EL1	3	0	0	5	0
+Enum	63:60	HPMN0
+	0b0000	UNPREDICTABLE
+	0b0001	DEF
+EndEnum
+Res0	59:56
+Enum	55:52	BRBE
+	0b0000	NI
+	0b0001	IMP
+	0b0010	BRBE_V1P1
+EndEnum
+Enum	51:48	MTPMU
+	0b0000	NI_IMPDEF
+	0b0001	IMP
+	0b1111	NI
+EndEnum
+Enum	47:44	TraceBuffer
+	0b0000	NI
+	0b0001	IMP
+EndEnum
+Enum	43:40	TraceFilt
+	0b0000	NI
+	0b0001	IMP
+EndEnum
+Enum	39:36	DoubleLock
+	0b0000	IMP
+	0b1111	NI
+EndEnum
+Enum	35:32	PMSVer
+	0b0000	NI
+	0b0001	IMP
+	0b0010	V1P1
+	0b0011	V1P2
+	0b0100	V1P3
+EndEnum
+Field	31:28	CTX_CMPs
+Res0	27:24
+Field	23:20	WRPs
+Res0	19:16
+Field	15:12	BRPs
+Enum	11:8	PMUVer
+	0b0000	NI
+	0b0001	IMP
+	0b0100	V3P1
+	0b0101	V3P4
+	0b0110	V3P5
+	0b0111	V3P7
+	0b1000	V3P8
+	0b1111	IMP_DEF
+EndEnum
+Enum	7:4	TraceVer
+	0b0000	NI
+	0b0001	IMP
+EndEnum
+Enum	3:0	DebugVer
+	0b0110	IMP
+	0b0111	VHE
+	0b1000	V8P2
+	0b1001	V8P4
+	0b1010	V8P8
+EndEnum
+EndSysreg
+
+Sysreg	ID_AA64DFR1_EL1	3	0	0	5	1
+Res0	63:0
+EndSysreg
+
+Sysreg	ID_AA64AFR0_EL1	3	0	0	5	4
+Res0	63:32
+Field	31:28	IMPDEF7
+Field	27:24	IMPDEF6
+Field	23:20	IMPDEF5
+Field	19:16	IMPDEF4
+Field	15:12	IMPDEF3
+Field	11:8	IMPDEF2
+Field	7:4	IMPDEF1
+Field	3:0	IMPDEF0
+EndSysreg
+
+Sysreg	ID_AA64AFR1_EL1	3	0	0	5	5
+Res0	63:0
+EndSysreg
+
+Sysreg	ID_AA64ISAR0_EL1	3	0	0	6	0
+Enum	63:60	RNDR
+	0b0000	NI
+	0b0001	IMP
+EndEnum
+Enum	59:56	TLB
+	0b0000	NI
+	0b0001	OS
+	0b0010	RANGE
+EndEnum
+Enum	55:52	TS
+	0b0000	NI
+	0b0001	FLAGM
+	0b0010	FLAGM2
+EndEnum
+Enum	51:48	FHM
+	0b0000	NI
+	0b0001	IMP
+EndEnum
+Enum	47:44	DP
+	0b0000	NI
+	0b0001	IMP
+EndEnum
+Enum	43:40	SM4
+	0b0000	NI
+	0b0001	IMP
+EndEnum
+Enum	39:36	SM3
+	0b0000	NI
+	0b0001	IMP
+EndEnum
+Enum	35:32	SHA3
+	0b0000	NI
+	0b0001	IMP
+EndEnum
+Enum	31:28	RDM
+	0b0000	NI
+	0b0001	IMP
+EndEnum
+Enum	27:24	TME
+	0b0000	NI
+	0b0001	IMP
+EndEnum
+Enum	23:20	ATOMIC
+	0b0000	NI
+	0b0010	IMP
+EndEnum
+Enum	19:16	CRC32
+	0b0000	NI
+	0b0001	IMP
+EndEnum
+Enum	15:12	SHA2
+	0b0000	NI
+	0b0001	SHA256
+	0b0010	SHA512
+EndEnum
+Enum	11:8	SHA1
+	0b0000	NI
+	0b0001	IMP
+EndEnum
+Enum	7:4	AES
+	0b0000	NI
+	0b0001	AES
+	0b0010	PMULL
+EndEnum
+Res0	3:0
+EndSysreg
+
+Sysreg	ID_AA64ISAR1_EL1	3	0	0	6	1
+Enum	63:60	LS64
+	0b0000	NI
+	0b0001	LS64
+	0b0010	LS64_V
+	0b0011	LS64_ACCDATA
+EndEnum
+Enum	59:56	XS
+	0b0000	NI
+	0b0001	IMP
+EndEnum
+Enum	55:52	I8MM
+	0b0000	NI
+	0b0001	IMP
+EndEnum
+Enum	51:48	DGH
+	0b0000	NI
+	0b0001	IMP
+EndEnum
+Enum	47:44	BF16
+	0b0000	NI
+	0b0001	IMP
+	0b0010	EBF16
+EndEnum
+Enum	43:40	SPECRES
+	0b0000	NI
+	0b0001	IMP
+EndEnum
+Enum	39:36	SB
+	0b0000	NI
+	0b0001	IMP
+EndEnum
+Enum	35:32	FRINTTS
+	0b0000	NI
+	0b0001	IMP
+EndEnum
+Enum	31:28	GPI
+	0b0000	NI
+	0b0001	IMP
+EndEnum
+Enum	27:24	GPA
+	0b0000	NI
+	0b0001	IMP
+EndEnum
+Enum	23:20	LRCPC
+	0b0000	NI
+	0b0001	IMP
+	0b0010	LRCPC2
+EndEnum
+Enum	19:16	FCMA
+	0b0000	NI
+	0b0001	IMP
+EndEnum
+Enum	15:12	JSCVT
+	0b0000	NI
+	0b0001	IMP
+EndEnum
+Enum	11:8	API
+	0b0000	NI
+	0b0001	PAuth
+	0b0010	EPAC
+	0b0011	PAuth2
+	0b0100	FPAC
+	0b0101	FPACCOMBINE
+EndEnum
+Enum	7:4	APA
+	0b0000	NI
+	0b0001	PAuth
+	0b0010	EPAC
+	0b0011	PAuth2
+	0b0100	FPAC
+	0b0101	FPACCOMBINE
+EndEnum
+Enum	3:0	DPB
+	0b0000	NI
+	0b0001	IMP
+	0b0010	DPB2
+EndEnum
+EndSysreg
+
+Sysreg	ID_AA64ISAR2_EL1	3	0	0	6	2
+Res0	63:28
+Enum	27:24	PAC_frac
+	0b0000	NI
+	0b0001	IMP
+EndEnum
+Enum	23:20	BC
+	0b0000	NI
+	0b0001	IMP
+EndEnum
+Enum	19:16	MOPS
+	0b0000	NI
+	0b0001	IMP
+EndEnum
+Enum	15:12	APA3
+	0b0000	NI
+	0b0001	PAuth
+	0b0010	EPAC
+	0b0011	PAuth2
+	0b0100	FPAC
+	0b0101	FPACCOMBINE
+EndEnum
+Enum	11:8	GPA3
+	0b0000	NI
+	0b0001	IMP
+EndEnum
+Enum	7:4	RPRES
+	0b0000	NI
+	0b0001	IMP
+EndEnum
+Enum	3:0	WFxT
+	0b0000	NI
+	0b0010	IMP
+EndEnum
+EndSysreg
+
+Sysreg	ID_AA64MMFR0_EL1	3	0	0	7	0
+Enum	63:60	ECV
+	0b0000	NI
+	0b0001	IMP
+	0b0010	CNTPOFF
+EndEnum
+Enum	59:56	FGT
+	0b0000	NI
+	0b0001	IMP
+EndEnum
+Res0	55:48
+Enum	47:44	EXS
+	0b0000	NI
+	0b0001	IMP
+EndEnum
+Enum	43:40	TGRAN4_2
+	0b0000	TGRAN4
+	0b0001	NI
+	0b0010	IMP
+	0b0011	52_BIT
+EndEnum
+Enum	39:36	TGRAN64_2
+	0b0000	TGRAN64
+	0b0001	NI
+	0b0010	IMP
+EndEnum
+Enum	35:32	TGRAN16_2
+	0b0000	TGRAN16
+	0b0001	NI
+	0b0010	IMP
+	0b0011	52_BIT
+EndEnum
+Enum	31:28	TGRAN4
+	0b0000	IMP
+	0b0001	52_BIT
+	0b1111	NI
+EndEnum
+Enum	27:24	TGRAN64
+	0b0000	IMP
+	0b1111	NI
+EndEnum
+Enum	23:20	TGRAN16
+	0b0000	NI
+	0b0001	IMP
+	0b0010	52_BIT
+EndEnum
+Enum	19:16	BIGENDEL0
+	0b0000	NI
+	0b0001	IMP
+EndEnum
+Enum	15:12	SNSMEM
+	0b0000	NI
+	0b0001	IMP
+EndEnum
+Enum	11:8	BIGEND
+	0b0000	NI
+	0b0001	IMP
+EndEnum
+Enum	7:4	ASIDBITS
+	0b0000	8
+	0b0010	16
+EndEnum
+Enum	3:0	PARANGE
+	0b0000	32
+	0b0001	36
+	0b0010	40
+	0b0011	42
+	0b0100	44
+	0b0101	48
+	0b0110	52
+EndEnum
+EndSysreg
+
+Sysreg	ID_AA64MMFR1_EL1	3	0	0	7	1
+Enum	63:60	ECBHB
+	0b0000	NI
+	0b0001	IMP
+EndEnum
+Enum	59:56	CMOW
+	0b0000	NI
+	0b0001	IMP
+EndEnum
+Enum	55:52	TIDCP1
+	0b0000	NI
+	0b0001	IMP
+EndEnum
+Enum	51:48	nTLBPA
+	0b0000	NI
+	0b0001	IMP
+EndEnum
+Enum	47:44	AFP
+	0b0000	NI
+	0b0001	IMP
+EndEnum
+Enum	43:40	HCX
+	0b0000	NI
+	0b0001	IMP
+EndEnum
+Enum	39:36	ETS
+	0b0000	NI
+	0b0001	IMP
+EndEnum
+Enum	35:32	TWED
+	0b0000	NI
+	0b0001	IMP
+EndEnum
+Enum	31:28	XNX
+	0b0000	NI
+	0b0001	IMP
+EndEnum
+Enum	27:24	SpecSEI
+	0b0000	NI
+	0b0001	IMP
+EndEnum
+Enum	23:20	PAN
+	0b0000	NI
+	0b0001	IMP
+	0b0010	PAN2
+	0b0011	PAN3
+EndEnum
+Enum	19:16	LO
+	0b0000	NI
+	0b0001	IMP
+EndEnum
+Enum	15:12	HPDS
+	0b0000	NI
+	0b0001	IMP
+	0b0010	HPDS2
+EndEnum
+Enum	11:8	VH
+	0b0000	NI
+	0b0001	IMP
+EndEnum
+Enum	7:4	VMIDBits
+	0b0000	8
+	0b0010	16
+EndEnum
+Enum	3:0	HAFDBS
+	0b0000	NI
+	0b0001	AF
+	0b0010	DBM
+EndEnum
+EndSysreg
+
+Sysreg	ID_AA64MMFR2_EL1	3	0	0	7	2
+Enum	63:60	E0PD
+	0b0000	NI
+	0b0001	IMP
+EndEnum
+Enum	59:56	EVT
+	0b0000	NI
+	0b0001	IMP
+	0b0010	TTLBxS
+EndEnum
+Enum	55:52	BBM
+	0b0000	0
+	0b0001	1
+	0b0010	2
+EndEnum
+Enum	51:48	TTL
+	0b0000	NI
+	0b0001	IMP
+EndEnum
+Res0	47:44
+Enum	43:40	FWB
+	0b0000	NI
+	0b0001	IMP
+EndEnum
+Enum	39:36	IDS
+	0b0000	0x0
+	0b0001	0x18
+EndEnum
+Enum	35:32	AT
+	0b0000	NI
+	0b0001	IMP
+EndEnum
+Enum	31:28	ST
+	0b0000	39
+	0b0001	48_47
+EndEnum
+Enum	27:24	NV
+	0b0000	NI
+	0b0001	IMP
+	0b0010	NV2
+EndEnum
+Enum	23:20	CCIDX
+	0b0000	32
+	0b0001	64
+EndEnum
+Enum	19:16	VARange
+	0b0000	48
+	0b0001	52
+EndEnum
+Enum	15:12	IESB
+	0b0000	NI
+	0b0001	IMP
+EndEnum
+Enum	11:8	LSM
+	0b0000	NI
+	0b0001	IMP
+EndEnum
+Enum	7:4	UAO
+	0b0000	NI
+	0b0001	IMP
+EndEnum
+Enum	3:0	CnP
+	0b0000	NI
+	0b0001	IMP
+EndEnum
+EndSysreg
+
+Sysreg	SCTLR_EL1	3	0	1	0	0
+Field	63	TIDCP
+Field	62	SPINTMASK
+Field	61	NMI
+Field	60	EnTP2
+Res0	59:58
+Field	57	EPAN
+Field	56	EnALS
+Field	55	EnAS0
+Field	54	EnASR
+Field	53	TME
+Field	52	TME0
+Field	51	TMT
+Field	50	TMT0
+Field	49:46	TWEDEL
+Field	45	TWEDEn
+Field	44	DSSBS
+Field	43	ATA
+Field	42	ATA0
+Enum	41:40	TCF
+	0b00	NONE
+	0b01	SYNC
+	0b10	ASYNC
+	0b11	ASYMM
+EndEnum
+Enum	39:38	TCF0
+	0b00	NONE
+	0b01	SYNC
+	0b10	ASYNC
+	0b11	ASYMM
+EndEnum
+Field	37	ITFSB
+Field	36	BT1
+Field	35	BT0
+Res0	34
+Field	33	MSCEn
+Field	32	CMOW
+Field	31	EnIA
+Field	30	EnIB
+Field	29	LSMAOE
+Field	28	nTLSMD
+Field	27	EnDA
+Field	26	UCI
+Field	25	EE
+Field	24	E0E
+Field	23	SPAN
+Field	22	EIS
+Field	21	IESB
+Field	20	TSCXT
+Field	19	WXN
+Field	18	nTWE
+Res0	17
+Field	16	nTWI
+Field	15	UCT
+Field	14	DZE
+Field	13	EnDB
+Field	12	I
+Field	11	EOS
+Field	10	EnRCTX
+Field	9	UMA
+Field	8	SED
+Field	7	ITD
+Field	6	nAA
+Field	5	CP15BEN
+Field	4	SA0
+Field	3	SA
+Field	2	C
+Field	1	A
+Field	0	M
+EndSysreg
+
+SysregFields	CPACR_ELx
+Res0	63:29
+Field	28	TTA
+Res0	27:26
+Field	25:24	SMEN
+Res0	23:22
+Field	21:20	FPEN
+Res0	19:18
+Field	17:16	ZEN
+Res0	15:0
+EndSysregFields
+
+Sysreg	CPACR_EL1	3	0	1	0	2
+Fields	CPACR_ELx
+EndSysreg
+
+Sysreg	SMPRI_EL1	3	0	1	2	4
+Res0	63:4
+Field	3:0	PRIORITY
+EndSysreg
+
+SysregFields	ZCR_ELx
+Res0	63:9
+Raz	8:4
+Field	3:0	LEN
+EndSysregFields
+
+Sysreg ZCR_EL1	3	0	1	2	0
+Fields ZCR_ELx
+EndSysreg
+
+SysregFields	SMCR_ELx
+Res0	63:32
+Field	31	FA64
+Res0	30:9
+Raz	8:4
+Field	3:0	LEN
+EndSysregFields
+
+Sysreg	SMCR_EL1	3	0	1	2	6
+Fields	SMCR_ELx
+EndSysreg
+
+Sysreg	ALLINT	3	0	4	3	0
+Res0	63:14
+Field	13	ALLINT
+Res0	12:0
+EndSysreg
+
+Sysreg	FAR_EL1	3	0	6	0	0
+Field	63:0	ADDR
+EndSysreg
+
+SysregFields	CONTEXTIDR_ELx
+Res0	63:32
+Field	31:0	PROCID
+EndSysregFields
+
+Sysreg	CONTEXTIDR_EL1	3	0	13	0	1
+Fields	CONTEXTIDR_ELx
+EndSysreg
+
+Sysreg	TPIDR_EL1	3	0	13	0	4
+Field	63:0	ThreadID
+EndSysreg
+
+Sysreg	SCXTNUM_EL1	3	0	13	0	7
+Field	63:0	SoftwareContextNumber
+EndSysreg
+
+Sysreg	CLIDR_EL1	3	1	0	0	1
+Res0	63:47
+Field	46:33	Ttypen
+Field	32:30	ICB
+Field	29:27	LoUU
+Field	26:24	LoC
+Field	23:21	LoUIS
+Field	20:18	Ctype7
+Field	17:15	Ctype6
+Field	14:12	Ctype5
+Field	11:9	Ctype4
+Field	8:6	Ctype3
+Field	5:3	Ctype2
+Field	2:0	Ctype1
+EndSysreg
+
+Sysreg	GMID_EL1	3	1	0	0	4
+Res0	63:4
+Field	3:0	BS
+EndSysreg
+
+Sysreg	SMIDR_EL1	3	1	0	0	6
+Res0	63:32
+Field	31:24	IMPLEMENTER
+Field	23:16	REVISION
+Field	15	SMPS
+Res0	14:12
+Field	11:0	AFFINITY
+EndSysreg
+
+Sysreg	CSSELR_EL1	3	2	0	0	0
+Res0	63:5
+Field	4	TnD
+Field	3:1	Level
+Field	0	InD
+EndSysreg
+
+Sysreg	CTR_EL0	3	3	0	0	1
+Res0	63:38
+Field	37:32	TminLine
+Res1	31
+Res0	30
+Field	29	DIC
+Field	28	IDC
+Field	27:24	CWG
+Field	23:20	ERG
+Field	19:16	DminLine
+Enum	15:14	L1Ip
+	0b00	VPIPT
+	# This is named as AIVIVT in the ARM but documented as reserved
+	0b01	RESERVED
+	0b10	VIPT
+	0b11	PIPT
+EndEnum
+Res0	13:4
+Field	3:0	IminLine
+EndSysreg
+
+Sysreg	DCZID_EL0	3	3	0	0	7
+Res0	63:5
+Field	4	DZP
+Field	3:0	BS
+EndSysreg
+
+Sysreg	SVCR	3	3	4	2	2
+Res0	63:2
+Field	1	ZA
+Field	0	SM
+EndSysreg
+
+Sysreg	ZCR_EL2	3	4	1	2	0
+Fields	ZCR_ELx
+EndSysreg
+
+Sysreg	HCRX_EL2	3	4	1	2	2
+Res0	63:12
+Field	11	MSCEn
+Field	10	MCE2
+Field	9	CMOW
+Field	8	VFNMI
+Field	7	VINMI
+Field	6	TALLINT
+Field	5	SMPME
+Field	4	FGTnXS
+Field	3	FnXS
+Field	2	EnASR
+Field	1	EnALS
+Field	0	EnAS0
+EndSysreg
+
+Sysreg	SMPRIMAP_EL2	3	4	1	2	5
+Field	63:60	P15
+Field	59:56	P14
+Field	55:52	P13
+Field	51:48	P12
+Field	47:44	P11
+Field	43:40	P10
+Field	39:36	F9
+Field	35:32	P8
+Field	31:28	P7
+Field	27:24	P6
+Field	23:20	P5
+Field	19:16	P4
+Field	15:12	P3
+Field	11:8	P2
+Field	7:4	P1
+Field	3:0	P0
+EndSysreg
+
+Sysreg	SMCR_EL2	3	4	1	2	6
+Fields	SMCR_ELx
+EndSysreg
+
+Sysreg	DACR32_EL2	3	4	3	0	0
+Res0	63:32
+Field	31:30	D15
+Field	29:28	D14
+Field	27:26	D13
+Field	25:24	D12
+Field	23:22	D11
+Field	21:20	D10
+Field	19:18	D9
+Field	17:16	D8
+Field	15:14	D7
+Field	13:12	D6
+Field	11:10	D5
+Field	9:8	D4
+Field	7:6	D3
+Field	5:4	D2
+Field	3:2	D1
+Field	1:0	D0
+EndSysreg
+
+Sysreg	FAR_EL2	3	4	6	0	0
+Field	63:0	ADDR
+EndSysreg
+
+Sysreg	CONTEXTIDR_EL2	3	4	13	0	1
+Fields	CONTEXTIDR_ELx
+EndSysreg
+
+Sysreg	CPACR_EL12	3	5	1	0	2
+Fields	CPACR_ELx
+EndSysreg
+
+Sysreg	ZCR_EL12	3	5	1	2	0
+Fields	ZCR_ELx
+EndSysreg
+
+Sysreg	SMCR_EL12	3	5	1	2	6
+Fields	SMCR_ELx
+EndSysreg
+
+Sysreg	FAR_EL12	3	5	6	0	0
+Field	63:0	ADDR
+EndSysreg
+
+Sysreg	CONTEXTIDR_EL12	3	5	13	0	1
+Fields	CONTEXTIDR_ELx
+EndSysreg
+
+SysregFields TTBRx_EL1
+Field	63:48	ASID
+Field	47:1	BADDR
+Field	0	CnP
+EndSysregFields
+
+Sysreg	TTBR0_EL1	3	0	2	0	0
+Fields	TTBRx_EL1
+EndSysreg
+
+Sysreg	TTBR1_EL1	3	0	2	0	1
+Fields	TTBRx_EL1
+EndSysreg
+
+Sysreg	LORSA_EL1	3	0	10	4	0
+Res0	63:52
+Field	51:16	SA
+Res0	15:1
+Field	0	Valid
+EndSysreg
+
+Sysreg	LOREA_EL1	3	0	10	4	1
+Res0	63:52
+Field	51:48	EA_51_48
+Field	47:16	EA_47_16
+Res0	15:0
+EndSysreg
+
+Sysreg	LORN_EL1	3	0	10	4	2
+Res0	63:8
+Field	7:0	Num
+EndSysreg
+
+Sysreg	LORC_EL1	3	0	10	4	3
+Res0	63:10
+Field	9:2	DS
+Res0	1
+Field	0	EN
+EndSysreg
+
+Sysreg	LORID_EL1	3	0	10	4	7
+Res0	63:24
+Field	23:16	LD
+Res0	15:8
+Field	7:0	LR
+EndSysreg
diff --git a/arch/arm/plat-pxa/mfp.c b/drivers/soc/pxa/mfp.c
index 17fc4f33f35b..6220ba321cfc 100644
--- a/arch/arm/plat-pxa/mfp.c
+++ b/drivers/soc/pxa/mfp.c
@@ -15,7 +15,7 @@
 #include <linux/init.h>
 #include <linux/io.h>
 
-#include <plat/mfp.h>
+#include <linux/soc/pxa/mfp.h>
 
 #define MFPR_SIZE	(PAGE_SIZE)
 
diff --git a/arch/arm/plat-pxa/ssp.c b/drivers/soc/pxa/ssp.c
index 563440315acd..93449fb3519e 100644
--- a/arch/arm/plat-pxa/ssp.c
+++ b/drivers/soc/pxa/ssp.c
@@ -180,11 +180,7 @@ static int pxa_ssp_probe(struct platform_device *pdev)
 
 static int pxa_ssp_remove(struct platform_device *pdev)
 {
-	struct ssp_device *ssp;
-
-	ssp = platform_get_drvdata(pdev);
-	if (ssp == NULL)
-		return -ENODEV;
+	struct ssp_device *ssp = platform_get_drvdata(pdev);
 
 	mutex_lock(&ssp_lock);
 	list_del(&ssp->node);
diff --git a/arch/arm/mach-omap1/lcd_dma.c b/drivers/video/fbdev/omap/lcd_dma.c
index a72ac0c02b4f..f85817635a8c 100644
--- a/arch/arm/mach-omap1/lcd_dma.c
+++ b/drivers/video/fbdev/omap/lcd_dma.c
@@ -25,8 +25,11 @@
 
 #include <linux/omap-dma.h>
 
-#include <mach/hardware.h>
-#include <mach/lcdc.h>
+#include <linux/soc/ti/omap1-soc.h>
+#include <linux/soc/ti/omap1-io.h>
+
+#include "lcdc.h"
+#include "lcd_dma.h"
 
 int omap_lcd_dma_running(void)
 {
diff --git a/arch/arm/mach-omap1/include/mach/lcd_dma.h b/drivers/video/fbdev/omap/lcd_dma.h
index 1a3c0cf17899..1b4780197381 100644
--- a/arch/arm/mach-omap1/include/mach/lcd_dma.h
+++ b/drivers/video/fbdev/omap/lcd_dma.h
@@ -60,6 +60,4 @@ extern void omap_set_lcd_dma_b1_vxres(unsigned long vxres);
 extern void omap_set_lcd_dma_b1_mirror(int mirror);
 extern void omap_set_lcd_dma_b1_scale(unsigned int xscale, unsigned int yscale);
 
-extern int omap_lcd_dma_running(void);
-
 #endif /* __MACH_OMAP1_LCD_DMA_H__ */
diff --git a/arch/arm/mach-imx/Makefile.boot b/scripts/dummy-tools/dummy-plugin-dir/include/plugin-version.h
index e69de29bb2d1..e69de29bb2d1 100644
--- a/arch/arm/mach-imx/Makefile.boot
+++ b/scripts/dummy-tools/dummy-plugin-dir/include/plugin-version.h